WorldWideScience

Sample records for cement plant estonia

  1. Carbonate cementation in the late glacial outwash and beach deposits in northern Estonia

    Directory of Open Access Journals (Sweden)

    Maris Rattas

    2014-02-01

    Full Text Available The sedimentary environments, morphology and formation of carbonate cement in the late glacial glaciofluvial outwash and beach deposits in northern Estonia are discussed. Cementation is observed in well-drained, highly porous carbonaceous debris-rich gravel and sand-forming, resistant ledges in otherwise unconsolidated sediments. The cemented units occur as laterally continuous layers or as isolated lenticular patches with thicknesses from a few centimetres to 3 m. The cement is found in two main morphologies: (1 cement crusts or coatings around detrital grains and (2 massive cement almost entirely filling interparticle pores and intraparticle voids. It is exclusively composed of low-Mg calcite with angular equant to slightly elongated rhombohedral and scalenohedral or prismatic crystals, which indicate precipitation from meteoric or connate fresh surface (glacial lake water and/or near-surface groundwater under low to moderate supersaturation and flow conditions. The absence of organic structures within the cement suggests that cementation is essentially inorganic. The cement exhibits both meteoric vadose and phreatic features and most probably occurred close to the vadose–phreatic interface, where the conditions were transitional and/or fluctuating. Cementation has mainly taken place by CO2-degassing in response to fluctuations in groundwater level and flow conditions, controlled by the Baltic Ice Lake water level, and seasonal cold and/or dry climate conditions.

  2. Estonia

    Energy Technology Data Exchange (ETDEWEB)

    1999-09-01

    The Estonian Country Case Study concentrated on the energy sector. Estonia is in the process of intensive transition from a centrally planned to a market economy. The reforming of the whole economy, included the energy sector, is underway at present in Estonia, therefore the current situation is permanently changing. This in its turn complicates the overall characterisation of the situation and makes it difficult to have well founded basis for furhter forecasts and projections. However, the main lines of further development have been worked out in the governmental document `Long Term Development Plan for the Estonian Fuel and Energy Sector`, which was adopted by the Parliament (Riigikogu) in February 1998. The Estonian Country Case Study team has managed with the complicated task to analyse the most probable GHG mitigation options to be used for the period up till 2035. MARKAL and MARKAL-MACRO models were used to build up the energy system development scenarios and to analyse various GHG mitigation options. Two main scenarios, respectively with low and high GDP growth rates, were assumed for the present analysis. Also the impact of carbon tax on the choice of possible energy generation scenarios was studied with the help of the model. The results have been discussed in the context of future socio-economic and political restrictions. Special attention was paid to the problems and prospects of using Estonian main energy resource - oil shale - for the production of electricity. New combustion technologies developed in Estonia allow reducing CO{sub 2}, SO{sub 2} and NO{sub x} emissions, which makes them highly important in the process of following the binding agreements of international treaties on pollution abatement. The technological mitigation options of GHG emissions have been handled thoroughly, as they are of great interest for Estonia following the requirements of the Kyoto conference. Additionally, renewable energy sources were discussed more thoroughly

  3. Production of portland cement using Moroccan oil shale and comparative study between conventional cement plant and cement plant using oil shale

    International Nuclear Information System (INIS)

    Doumbouya, M.; Kacemi, K.E.; Kitane, S.

    2012-01-01

    Like the use of coal ash from power plants as an addition to cement, oil shale are used for cement production on an industrial scale in Estonia, China, USA and Germany. Oil shale can be utilized in manufacturing the cement. In addition to the utilization of these by-products after combustion, it can also reduce the required temperature for the clinkering reactions during the production of Portland clinker. We performed a study on the Moroccan oil shale to maximize the use of oil shale ash in the manufacturing of Portland cement. We found that Moroccan oil shale ash can be used up to 30% with 70% Portland clinker without altering its principle properties. The corresponding temperature required to generate the required liquid for the clinkering reactions as well as the essential ingredients for clinker was found to be around 850 to 1000 deg. C. The operating temperatures for this optimized blend ratio were found to 1000 deg. C. The resulting Portland clinker from this ratio will need further testing in accordance with international standards for Portland cement to examine properties like strength and setting time. (author)

  4. Modernization of Byuzmeyinsky Cement Plant

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, investigations and discussions were given on a modernization project for Byuzmeyinsky Cement Factory, the only cement factory in Turkmenistan. Byuzmeyinsky Cement Factory uses the wet process which consumes a large amount of energy, is inferior in production efficiency and quality, and discharging a great amount of greenhouse effect gas. The present project will execute change of the raw material crusher into a vertical roll mill for one of the four wet kilns, and change of the facilities for raw material powder mixing and storing and clinker manufacturing into dry-type facilities using the NSP system. As a result of the discussions, the energy saving effect would be 86,321 tons of crude oil equivalent annually, and the greenhouse gas emission reducing effect would be 224,467 t-CO2 annually. The total fund amount required for the project is estimated to be 90,211,000 dollars. With regard to the profitability, the internal financial profit rate would be 9.71% after tax, and the ROE would be 18.62%, whereas the project is considered feasible. (NEDO)

  5. Commented list of rare and protected vascular plants of inland water bodies of Estonia

    Directory of Open Access Journals (Sweden)

    Helle Mäemets

    2016-10-01

    Full Text Available This presented overview of rare and protected hydrophytes, emergent plants and hygrophytes of inland water bodies of Estonia includes 60 species. In the commented list are indicated their position in the state protection categories I–III (last version in 2014, and under the Red List of Estonia (last version in 2008; marked are Natura 2000 species of the European Union. Most typical habitats for these rare species are: I. soft-water oligotrophic and semidystrophic lakes; II. mesotrophic lakes with Najas (Caulinia flexilis and Potamogeton rutilus; III. alkaline fens and wet meadows; IV. brackish or freshwater coastal lagoons; V. undamaged river stretches; VI. open shallow littoral of the largest lakes of Peipsi (Pskovsko-Chudskoe and of Võrtsjärv. Main threats of these habitats are briefly concerned, as well as the problem of conservation value of hybrids, based on the example of Sparganium species.

  6. Data acquisition and monitoring of radwaste cementation plants

    International Nuclear Information System (INIS)

    Cable, A.S.; Lee, D.J.; Samways, J.; Weller, F.C.; Williams, J.R.A.

    1988-03-01

    This paper summarises the progress made in the two years to June 1987 on the DOE funded programme for Data acquisition and monitoring of Radwaste Cementation Plants. The results of the computer based data logging and processing system fitted to an in-drum mixing station, cement powder plant and sludge handling plant are reported. (author)

  7. Yemen watched from cement plant construction work. Cement plant koji wo toshite mita Yemen

    Energy Technology Data Exchange (ETDEWEB)

    Furuta, M [Kajima Corp., Tokyo (Japan)

    1993-06-25

    Construction of a cement plant was planned at southern part of Yemen. This is a cement plant with annual production 500,000 tons. The term of work was from January, 1990 to February, 1993. The present paper describes an outline the construction of this Cement Plant, the nationality and living environment in Yemen, and construction equipment which was used. The construction work consisted of 113,000m[sup 3] of digging, 82,000m[sup 3] of backfilling, 66,100m[sup 3] of concreting, and 29,285m[sup 3] of asphalt pavement. Reinforcing steel weighing 6,400 tons and steel frame weighing 3,600 tons were totally used. Equipment weighing 7,912 tons and electric devices weighing 1,299 tons were totally installed. For this construction work, two crawler cranes, six hydraulic cranes, aggregate plant, concrete mixers, and construction equipment, such as bulldozers, shovels, and dumpers, were brought from Japan. 5 figs.

  8. Petroleum Sludge as gypsum replacement in cement plants: Its Impact on Cement Strength

    Science.gov (United States)

    Benlamoudi, Ali; Kadir, Aeslina Abdul; Khodja, Mohamed

    2017-08-01

    Due to high cost of cement manufacturing and the huge amount of resources exhaustion, companies are trying to incorporate alternative raw materials or by-products into cement production so as to produce alternative sustainable cement. Petroleum sludge is a dangerous waste that poses serious imparts on soil and groundwater. Given that this sludge contains a high percentage of anhydrite (CaSO4), which is the main component of gypsum (CaSO4.2H2O), it may play the same gypsum role in strength development. In this research, a total replacement of gypsum (100%) has been substituted by petroleum sludge in cement production and has led to an increase of 28.8% in UCS values after 28 curing days. Nevertheless, the burning of this waste has emitted a considerable amount of carbon monoxide (CO) gas that needs to be carefully considered prior to use petroleum sludge within cement plants.

  9. Assessing the value of retrofitting cement plants for carbon capture: A case study of a cement plant in Guangdong, China

    International Nuclear Information System (INIS)

    Liang Xi; Li Jia

    2012-01-01

    Highlights: ► A techno-economic analysis on retrofitting cement plants to CO 2 capture is conducted. ► A list of criteria is suggested to investigate the CO 2 capture retrofit potential in cement plants. ► The baseline estimated cost of CO 2 avoidance for retrofitting a cement plant is US$70/tCO 2 e. ► The value of retrofit option is US$1.2 million with a 7.3% probability of economic viability. ► The retrofit option value reaches US$20 m with 67% probability under a high carbon price growth. - Abstract: The cement manufacturing sector is the second largest source of anthropogenic greenhouse gas emissions in the world. Carbon Capture and Storage (CCS) is one of the most important technologies to decarbonise the cement manufacturing process. China has accounted for more than half of global cement production since 2008. This study suggests criteria to assess the potential to retrofit cement plants and analyses the economics of retrofitting cement plants for CCS with a case study of a modern dry process cement plant locating in Guangdong province, China. The study assumes the extra heat and power for CO 2 capture and compression is provided by a new 200 MW combined heat and power unit (CHP) (US$17.5/MW h thermal for the cost of coal). The estimated cost of CO 2 avoidance by retrofitting a cement plant for carbon capture in 2012 is US$70/tonne at a 14% discount rate with 25 years remaining lifetime. Through a stochastic cash flow analysis with a real option model and Monte Carlo simulation, the study found the value of an option to retrofit to be US$1.2 million with a 7.3% probability of economic viability. The estimate is very sensitive to the assumptions in the carbon price model (i.e. base carbon price is US$12.00/tCO 2 e in 2012 and the mean growth rate is 8%). The option value and the probability can reach US$20 million and 67% respectively, if a 10% mean carbon price growth is assumed. Compared with post-combustion carbon capture retrofitting prospect in

  10. Iron in the Middle Devonian aquifer system and its removal at Võru County water treatment plants, Estonia

    OpenAIRE

    Mariina Hiiob; Enn Karro

    2012-01-01

    Groundwater abstracted from the Middle Devonian aquifer system is the main source of drinking water in South Estonia. High iron and manganese concentrations in groundwater are the greatest problems in this region. The total iron concentrations up to 16 mg L–1 are mainly caused by a high Fe2+ content in water, pointing to the dominance of reducing conditions in the aquifer system. A pilot study was carried out to estimate the effectiveness of 20 groundwater purification plants with eight diffe...

  11. Preterm delivery among people living around Portland cement plants

    International Nuclear Information System (INIS)

    Yang, C.-Y.; Chang, C.-C.; Tsai, S.-S.; Huang, H.-Y.; Ho, C.-K.; Wu, T.-N.; Sung, F.-C.

    2003-01-01

    The Portland cement industry is the main source of particulate air pollution in Kaohsiung city. Data in this study concern outdoor air pollution and the health of individuals living in communities in close proximity to Portland cement plants. The prevalence of delivery of preterm birth infants as significantly higher in mothers living within 0-2 km of a Portland cement plant than in mothers living within 2-4 km. After controlling for several possible confounders (including maternal age, season, marital status, maternal education, and infant sex), the adjusted odds ratio was 1.30 (95% I=1.09-1.54) for the delivery of preterm infants for mothers living close to he Portland cement plants, chosen at the start to be from 0 to 2 km. These data provide further support for the hypothesis that air pollution can affect he outcome of pregnancy

  12. Encapsulation of ILW raffinate in the Dounreay cementation plant

    International Nuclear Information System (INIS)

    Sinclair, G.F.

    1998-01-01

    The Dounreay Cementation Plant has been designed and constructed to encapsulate the first cycle liquid raffinate arising from the reprocessing of irradiated Research Reactor fuel into a cementitious matrix. The acidic liquid waste is conditioned with sodium hydroxide prior to mixing with the cement powders (a 9:1 ratio of Blast Furnace Slag / Ordinary Portland Cement with 5% Lime). The complete cement mixing process is performed within the 500-liter drum, which provides the waste package primary containment. The plant has recently been commissioned and has commenced routine operation, processing stocks of existing raffinate that has been stored at Dounreay for up to 30 years. The waste loading per drum has been optimised within the constraints of the chemical composition of the raffinate, with an expected plant throughput of 2.5 m 3 /week. (author)

  13. Carbonate Looping for De-Carbonization of Cement Plants

    DEFF Research Database (Denmark)

    Pathi, Sharat Kumar; Andersen, Maria Friberg; Lin, Weigang

    2011-01-01

    Cement industry is one of the largest emitter of CO2 other than power generation plants, which includes the emissions from combustion of fuel and also from calcination of limestone for clinker production. In order to reduce CO2 emissions from the cement industry an effective an economically...... feasible technology is to be developed. The carbonate looping process is a promising technology, which is particularly suitable for the cement industry as limestone could be used for capture and release of CO2. Integration of carbonate looping process into cement pyroprocess has two advantages: 1...... integrated into cement pyro-process. The energy required for regeneration in the calciner increases with increase in average conversion of calcined limestone and energy that can be extracted from carbonator decreases with increasing average conversion. Further the influence of type of limestone...

  14. Integration of oxygen membranes for oxygen production in cement plants

    DEFF Research Database (Denmark)

    Puig Arnavat, Maria; Søgaard, Martin; Hjuler, Klaus

    2015-01-01

    The present paper describes the integration of oxygen membranes in cement plants both from an energy, exergy and economic point of view. Different configurations for oxygen enrichment of the tertiary air for combustion in the pre-calciner and full oxy-fuel combustion in both pre-calciner and kiln...

  15. Trait-based analysis of decline in plant species ranges during the 20th century: a regional comparison between the UK and Estonia.

    Science.gov (United States)

    Laanisto, Lauri; Sammul, Marek; Kull, Tiiu; Macek, Petr; Hutchings, Michael J

    2015-02-02

    Although the distribution ranges and abundance of many plant species have declined dramatically in recent decades, detailed analysis of these changes and their cause have only become possible following the publication of second- and third-generation national distribution atlases. Decline can now be compared both between species and in different parts of species' ranges. We extracted data from distribution atlases to compare range persistence of 736 plant species common to both the UK and Estonia between survey periods encompassing almost the same years (1969 and 1999 in the UK and 1970 and 2004 in Estonia). We determined which traits were most closely associated with variation in species persistence, whether these were the same in each country, and the extent to which they explained differences in persistence between the countries. Mean range size declined less in Estonia than in the UK (24.3% vs. 30.3%). One-third of species in Estonia (239) maintained >90% of their distribution range compared with one-fifth (141) in the UK. In Estonia, 99 species lost >50% of their range compared with 127 species in the UK. Persistence was very positively related to original range in both countries. Major differences in species persistence between the studied countries were primarily determined by biogeographic (affiliation to floristic element) and ecoevolutionary (plant strategy) factors. In contrast, within-country persistence was most strongly determined by tolerance of anthropogenic activities. Decline of species in the families Orchidaceae and Potamogetonaceae was significantly greater in the UK than in Estonia. Almost all of the 736 common and native European plant species in our study are currently declining in their range due to pressure from anthropogenic activities. Those species with low tolerance of human activity, with biotic pollination vectors and in the families referred to above are the most vulnerable, especially where human population density is high. © 2015

  16. NEURO-FUZZY MODELLING OF BLENDING PROCESS IN CEMENT PLANT

    Directory of Open Access Journals (Sweden)

    Dauda Olarotimi Araromi

    2015-11-01

    Full Text Available The profitability of a cement plant depends largely on the efficient operation of the blending stage, therefore, there is a need to control the process at the blending stage in order to maintain the chemical composition of the raw mix near or at the desired value with minimum variance despite variation in the raw material composition. In this work, neuro-fuzzy model is developed for a dynamic behaviour of the system to predict the total carbonate content in the raw mix at different clay feed rates. The data used for parameter estimation and model validation was obtained from one of the cement plants in Nigeria. The data was pre-processed to remove outliers and filtered using smoothening technique in order to reveal its dynamic nature. Autoregressive exogenous (ARX model was developed for comparison purpose. ARX model gave high root mean square error (RMSE of 5.408 and 4.0199 for training and validation respectively. Poor fit resulting from ARX model is an indication of nonlinear nature of the process. However, both visual and statistical analyses on neuro-fuzzy (ANFIS model gave a far better result. RMSE of training and validation are 0.28167 and 0.7436 respectively, and the sum of square error (SSE and R-square are 39.6692 and 0.9969 respectively. All these are an indication of good performance of ANFIS model. This model can be used for control design of the process.

  17. Iron in the Middle Devonian aquifer system and its removal at Võru County water treatment plants, Estonia

    Directory of Open Access Journals (Sweden)

    Mariina Hiiob

    2012-08-01

    Full Text Available Groundwater abstracted from the Middle Devonian aquifer system is the main source of drinking water in South Estonia. High iron and manganese concentrations in groundwater are the greatest problems in this region. The total iron concentrations up to 16 mg L–1 are mainly caused by a high Fe2+ content in water, pointing to the dominance of reducing conditions in the aquifer system. A pilot study was carried out to estimate the effectiveness of 20 groundwater purification plants with eight different water treatment systems (aeration combined with Manganese Greensand, Birm, Nevtraco, Hydrolit-Mn, Magno-Dol and quartz sand filters in Võru County. The results demonstrate that in most cases the systems with pre-aeration effectively purify groundwater from iron, but only 13 out of 20 water treatment plants achieved a reduction of iron concentration to the level fixed in drinking water requirements (0.2 mg L–1. Manganese content decreased below the maximum allowed concentration in only 25% of systems and in cases where the filter media was Birm or quartz sand and pre-oxidation was applied. The study showed that the high level of iron purification does not guarantee effective removal of manganese.

  18. Complementary treatment of the common cold and flu with medicinal plants--results from two samples of pharmacy customers in Estonia.

    Science.gov (United States)

    Raal, Ain; Volmer, Daisy; Sõukand, Renata; Hratkevitš, Sofia; Kalle, Raivo

    2013-01-01

    The aim of the current survey was to investigate the complementary self-treatment of the common cold and flu with medicinal plants among pharmacy customers in Estonia. A multiple-choice questionnaire listing 10 plants and posing questions on the perceived characteristics of cold and flu, the effectiveness of plants, help-seeking behaviour, self-treatment and sources of information, was distributed to a sample of participants in two medium size pharmacies. The participants were pharmacy customers: 150 in Tallinn (mostly Russian speaking) and 150 in Kuressaare (mostly Estonian speaking). The mean number of plants used by participants was 4.1. Of the respondents, 69% self-treated the common cold and flu and 28% consulted with a general practitioner. In general, medicinal plants were considered effective in the treatment of the above-mentioned illnesses and 56% of the respondents had used exclusively medicinal plants or their combination with OTC medicines and other means of folk medicine for treatment. The use of medicinal plants increased with age and was more frequent among female than male respondents. Among Estonian-speaking customers lime flowers, blackcurrant and camomile were more frequently used, and among Russian speaking customers raspberry and lemon fruits. Regardless of some statistically significant differences in preferred species among different age, education, sex and nationality groups, the general attitude towards medicinal plants for self-treatment of the common cold and flu in Estonia was very favourable.

  19. Cementation and solidification of Rocky Flats Plant incinerator ash

    International Nuclear Information System (INIS)

    Phillips, J.A.; Semones, G.B.

    1994-01-01

    Cementation studies on various aqueous waste streams at Rocky Flats have shown this technology to be effective for immobilizing the RCRA constituents in the waste. Cementation is also being evaluated for encapsulation of incinerator ash. Experiments will initially evaluate a surrogate ash waste using a Taguchi experimental design to optimize the cement formulation and waste loading levels for this application. Variables of waste loading, fly ash additions, water/cement ratio, and cement type will be tested at three levels each during the course of this work. Tests will finally be conducted on actual waste using the optimized cement formulation developed from this testing. This progression of tests will evaluate the effectiveness of cement encapsulation for this waste stream without generating any additional wastes

  20. Plant-Wide Energy Efficiency Assessment at the Arizona Portland Cement Plant in Rillito, Arizona

    Energy Technology Data Exchange (ETDEWEB)

    Stephen J. Coppinger, P.E.; Bruce Colburn, Ph.D., P.E., CEM

    2007-05-17

    A Department of Energy Plant-wide Assessment was undertaken by Arizona Portland Cement (APC) beginning in May 2005. The assessment was performed at APC’s cement production facility in Rillito, Arizona. The assessment included a compressed air evaluation along with a detailed process audit of plant operations and equipment. The purpose of this Energy Survey was to identify a series of energy cost savings opportunities at the Plant, and provide preliminary cost and savings estimates for the work. The assessment was successful in identifying projects that could provide annual savings of over $2.7 million at an estimated capital cost of $4.3 million. If implemented, these projects could amount to a savings of over 4.9 million kWh/yr and 384,420 MMBtu/year.

  1. Thermodynamic and exergoeconomic analysis of a cement plant: Part I – Methodology

    International Nuclear Information System (INIS)

    Atmaca, Adem; Yumrutaş, Recep

    2014-01-01

    Highlights: • Energy, exergy and exergoeconomic analysis of a complete cement plant have been investigated. • The first and second law efficiencies based on the energy and exergy analysis are defined for the entire cement plant. • The specific energy consumption of the whole sections of the cement plant have been analyzed. • The specific manufacturing costs of farine, clinker and cement have been determined by the cost analysis. - Abstract: The energy, exergy and exergoeconomic analysis of a cement factory has been studied within two parts. This paper is the first part of the study which includes the thermodynamic and exergoeconomic methodology and formulations developed for such a comprehensive and detailed analysis. The second part of this study is about the application of the developed formulation which considers an actual cement plant located in Gaziantep, Turkey. The energy consumption by the cement industry is about 5% of the total global industrial energy consumption. It is also one of the world’s largest industrial sources of CO 2 emissions. In this paper, a cement plant is considered with all main manufacturing units. Mass, energy, and exergy balances are applied to each system. The first and second law efficiencies based on the energy and exergy analysis and performance assessment parameters are defined for the entire cement plant. The formulations for the cost of products, and cost formation and allocation within the system are developed based on exergoeconomic analysis. In order to obtain the optimal marketing price of cement and to decrease specific energy consumption of the whole plant, the cost analysis formulated here have substantial importance

  2. Thermodynamic and exergoeconomic analysis of a cement plant: Part II – Application

    International Nuclear Information System (INIS)

    Atmaca, Adem; Yumrutaş, Recep

    2014-01-01

    Highlights: • The overall energy and exergy efficiencies of the plant is found to be 59.37% and 38.99% respectively. • Performance assessment of a cement plant indicates that the calcination process involves the highest portion of energy losses. • The specific exergetic cost cement produced by the cement plant is calculated to be 180.5 USD/GJ. • The specific cement manufacturing cost is found to be 41.84 USD/ton. - Abstract: This paper is Part 2 of the study on the thermodynamic and exergoeconomic analysis of a cement plant. In Part 1, thermodynamic and exergoeconomic formulations and procedure for such a comprehensive analysis are provided while this paper provides an application of the developed formulation that considers an actual cement plant located in Gaziantep, Turkey. The overall energy and exergy efficiencies of the plant is found to be 59.37% and 38.99% respectively. The exergy destructions, exergetic cost allocations, and various exergoeconomic performance parameters are determined by using the exergoeconomic analysis based on specific exergy costing method (SPECO) for the entire plant and its components. The specific unit exergetic cost of the farine, clinker and cement produced by the cement plant are calculated to be 43.77 USD/GJ, 133.72 USD/GJ and 180.5 USD/GJ respectively. The specific manufacturing costs of farine, clinker and cement are found to be 3.8 USD/ton, 33.11 USD/ton and 41.84 USD/ton respectively

  3. Research of fluidized bed cement clinker sintering system by pilot plant; Ryudosho cement shosei gijutsu no kaihatsu. 7

    Energy Technology Data Exchange (ETDEWEB)

    Sugiyama, T [Center for Coal Utilization, Japan, Tokyo (Japan); Sato, N; Hashimoto, I; Nakatsuka, M [The Cement Association of Japan, Tokyo (Japan)

    1996-09-01

    While a cement manufacturing process generally performs sintering by using a rotary kiln, a development work has been carried out as a subsidy operation of the Agency of Natural Resources and Energy on a cement sintering technology using a fluidized bed consisted of two furnaces: a jet flow bed granulating furnace and a fluidized bed sintering furnace. This paper reports the results of tests and researches performed during fiscal 1995. A plant with a scale of 20 ton-a-day production started in 1993 after having gone through bench scale tests. The year 1995 conducted by August its performance evaluation, review of the operation method and the safety criteria, and generalization of the tests. A multi-stage cyclone system has been employed in the preheating equipment for cement material powder. A number of improvements have been realized in the aspects of construction and operation, such as stabilization of dust collecting efficiency by employing a high-efficiency type cyclone, and operation with reduced pressure variation. Based on these results, a construction had been progressed in parallel on a new plant upscaled to 200 ton-a-day production. The new plant was completed in December, 1995. 9 figs., 8 tabs.

  4. Mercury enrichment and its effects on atmospheric emissions in cement plants of China

    Science.gov (United States)

    Wang, Fengyang; Wang, Shuxiao; Zhang, Lei; Yang, Hai; Wu, Qingru; Hao, Jiming

    2014-08-01

    The cement industry is one of the most significant anthropogenic sources of atmospheric mercury emissions worldwide. In this study of three typical Chinese cement plants, mercury in kiln flue gas was sampled using the Ontario Hydro Method (OHM), and solid samples were analyzed. Particulate matter recycling, preheating of raw materials, and the use of coal and flue gas desulfurization derived gypsum contributed to emissions of Hg in the air and to accumulation in cement. Over 90% of the mercury input was emitted into the atmosphere. Mercury emission factors were 0.044-0.072 g/t clinker for the test plants. The major species emitted into the atmosphere from cement plants is oxidized mercury, accounting for 61%-91% of the total mercury in flue gas. The results of this study help improve the accuracy of the mercury emission inventory in China and provide useful information for developing mercury controls.

  5. Indoor occupational exposure to radiation at the Silmet plant in Estonia

    International Nuclear Information System (INIS)

    Mustonen, R.; Markkanen, M; Oksanen, E.; Rajamaee, R.

    2000-01-01

    The main pathways of indoor occupational exposure to radiation at Silmet plant are inhaled thoron daughters, external radiation, and inhaled particulate radioactivity. The exposure time to receive 1 mSv effective dose from inhaled long-lived particulate radioactivity and from external gamma radiation is estimated at about 700 hours at Workplace 1 and about 160 hours at Workplace 2. The results for Workplace 2 represent radiologically the most extreme conditions found in the workplaces. The results show that the exposure of workers due inhalation of long-lived radionuclides and to external gamma radiation may well exceed 1 mSv per year and, therefore, continuous monitoring of doses of workers seems to be justified

  6. Evaluation of energy efficiency opportunities of a typical Moroccan cement plant: Part I. Energy analysis

    International Nuclear Information System (INIS)

    Fellaou, S.; Bounahmidi, T.

    2017-01-01

    Highlights: • We have analyzed the degree of freedom of the overall system. • We validated the redundant measurements by the Lagrange multipliers technique. • We have analyzed the mass and the energy balances by two approaches. • We identified the factors that penalize the energetic performance of the whole plant. • We assessed options to improve energy efficiency of the entire cement plant. - Abstract: The cement industry is one of Morocco’s most highly energy intensive economic sectors. It suffers from abnormally high cost of energy supplies, representing more than two thirds of the cost of cement; the first item of expenditure is electricity and fuel with 40% and 30% respectively. Herefor, much more effort is needed to make the cement sector reach energy saving targets set by the Moroccan energy efficiency strategy. The present work aims to evaluate energy performance of an existing Moroccan cement plant based on a detailed mass and energy balances analysis. Redundant measurements were validated by the Lagrange multipliers technique before being used for the calculation of unmeasured variables. The values for energy consumption and related losses through the whole production line are reported, and the results obtained have been used to assess the energy performance of the process. The evaluation was completed by both an analysis of possible energy loss sources and important solutions described in the international literature to improve the energy efficiency of the entire cement plant.

  7. Pollutants emitted by a cement plant: health risks for the population living in the neighborhood

    International Nuclear Information System (INIS)

    Schuhmacher, Marta; Domingo, J.L.; Garreta, Josepa

    2004-01-01

    The aim of this study was to investigate the health risks due to combustor emissions in the manufacturing of Portland cement for the population living in the neighborhood of a cement kiln in Catalonia, Spain. Pollutants emitted to the atmosphere in the course of cement production were modeled. The ISC3-ST model was applied to estimate air dispersion of the contaminants emitted by the cement plant. Air concentrations of NO 2 , SO 2 , PM 10 , metals, and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), as well as the potential exposure in the vicinity of the facility, were assessed via models based on US EPA guidance documents. PCDD/F and metal concentrations were also modeled for soil and vegetation. Based on these concentrations, the levels of human exposure were calculated. Individual cancer and noncancer risks for the emissions of the cement kiln were assessed. Health effects due to NO 2 , SO 2 , and PM 10 emissions were also evaluated. Risk assessment was performed as a deterministic analysis. The main individual risk in the population was evaluated in a central-tendency and a high-end approach. The results show that the incremental individual risk due to emissions of the cement plant is very low not only with regard to health effects, but also in relation to toxicological and cancer risks produced by pollutants such as metals and PCDD/Fs emitted by the cement kiln

  8. Biomonitoring of airborne particulate matter emitted from a cement plant and comparison with dispersion modelling results

    Science.gov (United States)

    Abril, Gabriela A.; Wannaz, Eduardo D.; Mateos, Ana C.; Pignata, María L.

    2014-01-01

    The influence of a cement plant that incinerates industrial waste on the air quality of a region in the province of Córdoba, Argentina, was assessed by means of biomonitoring studies (effects of immission) and atmospheric dispersion (effects of emission) of PM10 with the application of the ISC3 model (Industrial Source Complex) developed by the USEPA (Environmental Protection Agency). For the biomonitoring studies, samples from the epiphyte plant Tillandsia capillaris Ruíz & Pav. f. capillaris were transplanted to the vicinities of the cement plant in order to determine the physiological damage and heavy metal accumulation (Ca, Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb). For the application of the ISC3 model, point and area sources from the cement plant were considered to obtain average PM10 concentration results from the biomonitoring exposure period. This model permitted it to be determined that the emissions from the cement plant (point and area sources) were confined to the vicinities, without significant dispersion in the study area. This was also observed in the biomonitoring study, which identified Ca, Cd and Pb, pH and electric conductivity (EC) as biomarkers of this cement plant. Vehicular traffic emissions and soil re-suspension could be observed in the biomonitors, giving a more complete scenario. In this study, biomonitoring studies along with the application of atmospheric dispersion models, allowed the atmospheric pollution to be assessed in more detail.

  9. Assessing Metal Exposures in a Community near a Cement Plant in the Northeast U.S.

    OpenAIRE

    Zhao Dong; Michael S. Bank; John D. Spengler

    2015-01-01

    Cement production is a major source of metals and metalloids in the environment, while exposures to metals and metalloids may impact human health in the surrounding communities. We recruited 185 participants living in the vicinity of a cement plant in the northeast U.S., and measured the levels of aluminum (Al), arsenic (As), cadmium (Cd), lead (Pb), mercury (Hg), and selenium (Se) in blood and Hg in hair samples from them. A questionnaire was used to assess potential sources of Hg exposure...

  10. Analysis of energy-efficiency opportunities for the cement industry in Shandong Province, China: A case study of 16 cement plants

    Energy Technology Data Exchange (ETDEWEB)

    Hasanbeigi, Ali; Price, Lynn; Lu, Hongyou [China Energy Group, Energy Analysis Department, Environmental Energy Technologies Division, Ernest Orlando Lawrence Berkeley National Laboratory, 1 Cyclotron Road, MS 90R4000, Berkeley, CA 94720 (United States); Lan, Wang [China Building Materials Academy, Guanzhuang, Chaoyang District, Beijing, Post code 100024 (China)

    2010-08-15

    In this study, 16 cement plants with New Suspension Preheater and pre-calciner (NSP) kiln were surveyed. Plant energy use was compared to both domestic (Chinese) and international best practice using the Benchmarking and Energy Saving Tool for Cement (BEST-Cement). This benchmarking exercise indicated an average technical potential primary energy savings of 12% would be possible if the surveyed plants operated at domestic best practice levels in terms of energy use per ton of cement produced. Average technical potential primary energy savings of 23% would be realized if the plants operated at international best practice levels. Then, using the bottom-up Electricity Conservation Supply Curve (ECSC) model, the cost-effective electricity efficiency potential for the 16 studied cement plants in 2008 is estimated to be 373 gigawatt-hours (GWh), and total technical electricity-saving potential is 915 GWh, which accounts for 16 and 40% of total electricity use in the studied plants in 2008, respectively. The Fuel Conservation Supply Curve (FCSC) model shows the total technical fuel efficiency potential equal to 7949 terajoules (TJ), accounting for 8% of total fuel used in the studied cement plants in 2008. All the fuel efficiency potential is shown to be cost effective. (author)

  11. Review: Circulation of Inorganic Elements in Combustion of Alternative Fuels in Cement Plants

    DEFF Research Database (Denmark)

    Cortada Mut, Maria del Mar; Nørskov, Linda Kaare; Jappe Frandsen, Flemming

    2015-01-01

    Cement production is an energy-intensive process, which traditionally has been dependent on fossil fuels. However, the use of alternative fuels, i.e., selected waste, biomass, and byproducts with recoverable calorific value, is constantly increasing. Combustion of these fuels is more challenging...... the internal circulation of S, Cl, Na, and K. Compounds containing these elements, such as alkali salts, evaporate when exposed to high temperatures and subsequently condense in colder parts of the plant. The transformation of the volatile inorganic species at different locations in the cement plant...... cycles of inorganic elements that are established within the cement plant and their dependence on process parameters. Special focus is given to the sulfur cycle. This cycle is intensified by CaSO4 decomposition, making it sensitive to local reducing conditions....

  12. Enrichment of {sup 210}Po and {sup 210}Pb in ash samples from oil shale-fired power plants in Estonia

    Energy Technology Data Exchange (ETDEWEB)

    Ozden, B. [University of Tartu, Institute of Physics/Ege University, Institute of Nuclear Sciences (Estonia); Vaasma, T.; Kiisk, M.; Suursoo, S.; Tkaczyk, A.H. [University of Tartu,Institute of Physics (Estonia)

    2014-07-01

    Energy production in Estonia is largely dependent on the oil shale industry. Oil shale is a fossil fuel typically characterized by relatively high mineral composition, modest organic fraction (varying between 10 and 65%), high ash content (usually 45% to 50%), and average lower heating value of 8.4 MJ/kg{sup -1}. Oil shale-fired power plants account for 85% of Estonian electricity production and produce up to 6 million tons of oil shale ash annually. This ash contains elevated amounts of natural radionuclides (from the {sup 238}U and {sup 232}Th series and {sup 40}K), which were bound to oil shale during its formation. These radionuclides become enriched in ash fractions during the combustion process and are partially emitted to the atmosphere via fly ash and flue gases. Oil shale-fired electricity production is foreseen to remain a dominant trend in Estonia, suggesting that the radionuclide emissions to the atmosphere will continue in the future. The natural radionuclides {sup 210}Po and {sup 210}Pb, with half-lives of 138 days and 22.3 years respectively, originate from the radioactive decay of radionuclides of {sup 238}U series present in the earth's crust. These radionuclides are also built up artificially in the environment due to waste discharge from phosphate, oil, and gas industries, combustion of fossil fuels and other energy production as technically enhanced natural radionuclides. There are few studies on oil shale power plants influence on the levels of natural radioactivity in the surrounding areas. Realo, et al. reported that the annual doses from fly ash depositions over a 30 year period are in the range 90 - 200 μSv a{sup -1}. A study previously initiated by the University of Tartu, Institute of Physics (IPh) evaluated enrichment in the activity concentrations of {sup 238}U, {sup 226}Ra, {sup 210}Pb, {sup 232}Th, {sup 228}Ra and {sup 40}K in ash samples collected from Eesti Power Plant's circulating fluidized bed (CFB) boiler. According

  13. Heat recovery from a cement plant with a Marnoch Heat Engine

    International Nuclear Information System (INIS)

    Saneipoor, P.; Naterer, G.F.; Dincer, I.

    2011-01-01

    This paper examines the performance of a new Marnoch Heat Engine (MHE) that recovers waste heat from within a typical cement plant. Two MHE units with compressed air as the working fluid are installed to recover the waste heat. The first unit on the main stack has four pairs of shell and tube heat exchangers. The second heat recovery unit is installed on a clinker quenching system. This unit operates with three pairs of shell and tube heat exchangers. The recovered heat is converted to electricity through the MHE system and used internally within the cement plant. A predictive model and results are presented and discussed. The results show the promising performance of the MHE's capabilities for efficient generation of electricity from waste heat sources in a cement plant. The new heat recovery system increases the efficiency of the cement plant and lowers the CO 2 emissions from the clinker production process. Moreover, it reduces the amount of waste heat to the environment and lowers the temperature of the exhaust gases. - Highlights: → This paper examines the thermodynamic performance of a new Marnoch Heat Engine (MHE) that recovers waste heat to produce electricity and improve the operating efficiency of a typical cement plant. → The first unit of the MHE on the main stack has four pairs of shell and tube heat exchangers and the second heat recovery unit is installed on a clinker quenching system. → Both predicted and experimental results demonstrate the promising performance of the MHE's capabilities for efficient generation of electricity from waste heat sources in a cement plant.

  14. Economy Profile of Estonia

    OpenAIRE

    World Bank Group

    2017-01-01

    Doing Business 2018 is the 15th in a series of annual reports investigating the regulations that enhance business activity and those that constrain it. This economy profile presents the Doing Business indicators for Estonia. Doing Business presents quantitative indicators on business regulation and the protection of property rights that can be compared across 190 economies; for 2018 Estonia ...

  15. Towards sustainable Estonia

    International Nuclear Information System (INIS)

    Lahtvee, Valdur

    1997-01-01

    Since 1989 the Estonian Green Movement has had a working group on energy issues. This group has tried to influence the energy policy in Estonia towards sustainable development. But the process has been hard. Five years have passed since Estonia has started with taking on its shoulders international environmental obligations. Unfortunately, Estonia is one of the last countries in Europe still to join the obligation on transboundary pollution. A master plan on energy is now prepared in Estonia within the framework of PHARE programme, involving quite a few high level specialists from various institutions in Estonia and assisted by foreign specialists. But the energy sector has not been open to public discussion in Estonia up to now. It's very important not to lose from sight the environmental problems in connection with energy sector development plans. The Estonian Green Movement together with its umbrella organization, the Friends of the Earth Europe, have worked out a new energy strategy for Estonia, based on the concept of environmental space. This concept has been used by some countries already on working out the strategy for their economic progress. The limit values for a set of basic mineral resources and local fuels of Estonia have been calculated on the basis of environmental space and economic targets set for the year 2010

  16. Methods and Production of Cementation Materials for Immobilisation into Waste Form. Research of Cementation Processes for Specific Liquid Radioactive Waste Streams of Radiochemical Plants

    International Nuclear Information System (INIS)

    Sukhanov, L.P.

    2013-01-01

    In the near future Russian Federation is planning to use industrial cementation facilities at two radiochemical combines - PA 'Mayak' and Mountain Chemical Combine. Scope of the research within the IAEA CRP contact No. 14176 included the development of cementation processes for specfic liquid radioactive waste streams that are present in these enterprisers. The research on cementation of liquid waste from spent nuclear fuel reprocessing at PA 'Mayak' allowed obtaining experimental data characterizing the technological process and basic characteristics of the produced cement compounds (e.g. mechanical strength, water resistance, frost resistance, flowability, etc.) immobilizing different streams of waste (e.g. hydrated-salt sludges, filter material pulps, mixture of hydrated salt slurries and filter material pulps, tritium liquid waste). Determined optimum technological parameters will allow industrial scale production of cement compound with required quality and higher flowability that is necessary for providing uniform filling of compartments of storage facilities at these sites. The research has been also carried out for the development of cementation technology for immobilization of pulps from storage tanks of Mountain Chemical Combine radiochemical plant. Cementation of such pulps is a difficult technological task because pulps are of complex chemical composition (e.g. hydroxides of manganese, iron, nickel, etc., as well as silicon oxide) and a relatively high activity. The research of cementation process selection for these pulps included studies of the impact of sorbing additive type and content on cement compounds leachability, flowability, impact of cement compound age to its mechanical strength, heat generation of cement compounds and others. The research results obtained allowed testing of cementation facility with a pulse type mixer on the full-scale. Use of such mixer for pulp cementation makes possible to prepare a homogeneous cement compound with the

  17. The thermoelectric generators use for waste heat utilization from cement plant

    Directory of Open Access Journals (Sweden)

    Sztekler Karol

    2017-01-01

    Production often entails the formation of by-product which is waste heat. One of the equipment processing heat into electricity is a thermoelectric generator. Its operation is based on the principle of thermoelectric phenomenon, which is known as a Seebeck phenomenon. The simplicity of thermoelectric phenomena allows its use in various industries, in which the main waste product is in the form of heat with the temperature of several hundred degrees. The study analyses the possibility of the thermoelectric systems use for the waste heat utilization resulting in the cement production at the cement plant. The location and design of the thermoelectric system that could be implemented in cement plant is chosen. The analysis has been prepared in the IPSEpro software.

  18. Studies on cement matrix materials used at the Radioactive Waste Treatment Plant for radwaste conditioning

    International Nuclear Information System (INIS)

    Dragolici, Felicia; Lungu, Laura; Nicu, Mihaela; Rotarescu, Gheorghe; Turcanu, Corneliu

    2003-01-01

    The research activities performed by Department of Radioactive Waste Management is focused on the treatment of LLAW products obtained by chemical precipitation and on the conditioning of these products by cementation. The individual mechanisms implied in the chemical precipitation processes are directly dependent on the precipitate properties and structure, which in turn are connected with the initial system composition and the precipitation procedure, i.e. reagent concentration, rate and orders of chemical addition, mixing rate and time and ageing conditions. In case of conditioning by cementation, the chemical nature and proportion of the sludges or concentrates affect both the hydrolysis of the initial cement components and the reactions of metastable hydration constituents, as well as the mechanical strength and chemical resistance of the hardened cemented matrix.Generally, the study of the precipitation products and their behaviour during cementation and the long-term disposal is extremely difficult because of the system complexity (phase composition and structure) and the lack of the non-destructive analytical methods. The experience accumulated by the countries who advanced nuclear programmes in military and socio-economic fields and which produced important volumes of radioactive wastes, leads us to study some of mineral additives to be used in the conditioning and disposal technology. Is well known that some mineral additives can diminish the leaching rate of the radionuclides in the disposal environment.The studies have the purpose to obtain the most propitious mixture of cement-bentonite and cement-volcanic tuff, which have the mechanical properties similar to the cement paste used for the conditioning of radioactive waste.Taking into account the characteristics of these mineral binders, namely a very good plasticity and capacity of adsorption, which lead at the decrease of porosity, the mixture is planned to be used in the future, at the Radioactive

  19. Where does the border lie: locally grown plants used for making tea for recreation and/or healing, 1970s-1990s Estonia.

    Science.gov (United States)

    Sõukand, Renata; Kalle, Raivo

    2013-10-28

    Traditional use of local wild and cultivated plants for making recreational tea in Estonia often borders with the medicinal use of the same plants. The aim of this paper is to map the perceptions of plants used for making tea and to define the domains of recreational and medicinal teas in specific cultural settings. Between November 2011 and March 2012 the authors distributed electronic questionnaires on the use of wild food plants in childhood. The questionnaire was answered by 250 respondents. 178 of them reported the use of plants for making recreational teas. The responses were analysed according to the taxonomy of the used plants, the most frequently used taxa and families were detected, the influence of respondents' demographic data on the number of use reports was assessed and the overlapping of medicinal and recreational uses was discussed. The study detected 69 vascular plant species, ten vascular taxa identified on the genera level only, and one lichen. The most popular families were Rosaceae, Asteraceae and Lamiacea, and 12 taxa were used by at least 10% of the respondents, while only one of them (Tilia) was used by more than 50% and one (Rubus idaeus) by over 33% of the respondents. The next ten most used taxa were: Rosa, Mentha, Primula veris, Matricaria, Achillea millefolium, Hypericum, Carum carvi, Urtica dioica, Thymus serpyllum and Fragaria. Of the 30 most used consolidated taxa mentioned in five or more use records, only four were used exclusively in one domain. The majority of the used plants were situated on the recreational-medicinal continuum, which could be divided into two domains: recreational, medicinal and the "grey" area that lies around the borderline. The predominance of the cold and cold-related diseases on the spectrum treated by plants used for making recreational tea reflects the climatic conditions of the region and suggests that they are the most commonly self-treated diseases in the region, seen from the child's perspective.

  20. Neutron activation as an online procedure in cement plants; Neutronenaktivierung als Online-Verfahren in Zementwerken

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2012-07-01

    The use of PGNAA (Prompt Gamma Neutron Activation Analysis) makes it possible to determine the content of the components in bulk flows in cement plants directly online on the conveyor belt. The nature of the excitation and radiation means that the material can be penetrated even with large layer thicknesses on the belt. (orig.)

  1. Recovery Act Production of Algal BioCrude Oil from Cement Plant Carbon Dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Robert Weber; Norman Whitton

    2010-09-30

    The consortium, led by Sunrise Ridge Algae Inc, completed financial, legal, siting, engineering and environmental permitting preparations for a proposed demonstration project that would capture stack gas from an operating cement plant and convert the carbon dioxide to beneficial use as a liquid crude petroleum substitute and a coal substitute, using algae grown in a closed system, then harvested and converted using catalyzed pyrolysis.

  2. [Influencing factors for hearing loss in workers exposed to noise in a cement plant].

    Science.gov (United States)

    Wang, X M; Wu, H; Jiao, J; Li, Y H; Zhang, Z R; Zhou, W H; Yu, S F

    2016-12-20

    Objective: To investigate the incidence of noise-induced hearing loss (NIHL) and related influencing factors in workers exposed to noise in a cement plant. Methods: In October 2015, cluster sampling was used for questionnaire investigation and health examination of workers exposed to noise in a cement plant in Henan Province, China. The association of demographic features, living habits, cumulative noise exposure (CNE) , hypertension, and hyperlipidemia with NIHL was analyzed. Results: There was mainly medium-or high-frequency noise in the working place of this cement plant. The prevalence rate of NIHL was 18.4%, and male workers had a significantly higher prevalence rate than female workers (χ(2)=28.09, P workers who smoked had a significantly higher prevalence rate of NIHL than those who did not smoke (χ(2)=14.15, P workers with a drinking habit had a significantly higher prevalence rate of NIHL than those without such habit (χ(2)=7.95, P workers who did not wear earplugs had a significantly higher prevalence rate of NIHL than those who wore earplugs (χ(2)=19.93, P workers with hyperlipidemiahad a significantly higher prevalence rate of NIHL than those without hyperlipidemia (χ(2)=12.43, P workers in a cement plant have a high prevalence rate of NIHL, and CNE, sex, age, degree of education, use of earplugs, and hyperlipidemia may be influencing factors for NIHL.

  3. A Hybrid Multidimensional Approach to Select a Country for Global Cement Plant Location

    Directory of Open Access Journals (Sweden)

    Muhammad Khurram Ali

    2015-04-01

    Full Text Available The globalization and saturated domestic markets force international firms to gradually expand their businesses across the borders to capture potential emerging markets. The decision to select a country for a new cement plant location demands analysis of a large number of factors. It is a multifaceted problem which requires investigation and prioritization of factors in a hierarchical way.This paper uses an FAHP (Fuzzy Analytic Hierarchy Process based procedure proposing a practical framework for solution of the GCPLP (Global Cement Plant Location Problem. It deals with real world ambiguities and handles a broader spectrum of influencing factors. The criteria for selection of a country for a new cement plant installation are prioritized from the FAHP based evaluation made by experts. Different global databases including the World Bank are used for the fuzzy ratings of the alternatives. It has been learnt in this particular problem that cement specific and cost related factors are the most sensitive while legal regulations and economic conditions are relatively less sensitive for the decision makers. Therefore, the countries having strong lime stone reserves, cheaper fuel costs and good internal marketing positions are higher in ranking. The paper concludes with different rankings of the four countries analyzed which assist the strategic managers in making decisions on the basis of mathematically computed results.

  4. A hybrid multidimensional approach to select a country for global cement plant location

    International Nuclear Information System (INIS)

    Ali, M.K.

    2015-01-01

    The globalization and saturated domestic markets force international firms to gradually expand their businesses across the borders to capture potential emerging markets. The decision to select a country for a new cement plant location demands analysis of a large number of factors. It is a multifaceted problem which requires investigation and prioritization of factors in a hierarchical way. This paper uses an FAHP (Fuzzy Analytic Hierarchy Process) based procedure proposing a practical framework for solution of the GCPLP (Global Cement Plant Location Problem). It deals with real world ambiguities and handles a broader spectrum of influencing factors. The criteria for selection of a country for a new cement plant installation are prioritized from the FAHP based evaluation made by experts. Different global databases including the World Bank are used for the fuzzy ratings of the alternatives. It has been learnt in this particular problem that cement specific and cost related factors are the most sensitive while legal regulations and economic conditions are relatively less sensitive for the decision makers. Therefore, the countries having strong lime stone reserves, cheaper fuel costs and good internal marketing positions are higher in ranking. The paper concludes with different rankings of the four countries analyzed which assist the strategic managers in making decisions on the basis of mathematically computed results. (author)

  5. Assessing Metal Exposures in a Community near a Cement Plant in the Northeast U.S.

    Directory of Open Access Journals (Sweden)

    Zhao Dong

    2015-01-01

    Full Text Available Cement production is a major source of metals and metalloids in the environment, while exposures to metals and metalloids may impact human health in the surrounding communities. We recruited 185 participants living in the vicinity of a cement plant in the northeast U.S., and measured the levels of aluminum (Al, arsenic (As, cadmium (Cd, lead (Pb, mercury (Hg, and selenium (Se in blood and Hg in hair samples from them. A questionnaire was used to assess potential sources of Hg exposure. Multivariate regressions and spatial analyses were performed to evaluate the relative importance of different routes of exposures. The metal concentrations in blood or hair samples of our study participants were comparable to the U.S. general or regional population. Smoking contributed significantly to Cd and Pb exposures, and seafood consumption contributed significantly to Hg and As exposures, while variables related to the cement plant were not significantly associated with metal concentrations. Our results suggest that our study population was not at elevated health risk due to metal exposures, and that the contribution of the cement plant to metal exposures in the surrounding community was minimal.

  6. Corrosivity of cement pastes with addition of sludge generated in water treatment plant

    International Nuclear Information System (INIS)

    Rodrigues, R.A.; Martins, B.E.D.B.S.; Couto, V.M.P.; Carvalho, L.J.; Almeida, V.C.

    2011-01-01

    The amount of sludge produced in a water treatment plant (WTP) is an important economic factor in the context of waste treatment. The present article has the objective of study the corrosion of cement pastes produced with blended sludge. Aqueous extracts were produced from the milling of masses containing 5%, 10% and 30% of sludge in relation to cement after 28 days of healing. These extracts were used for polarization assays in order to determine the corrosiveness of the folders when in contact with the used fittings. Moreover, other chemical analysis tests were carried out for sludge characterization: X-ray fluorescence and X-ray diffraction. The obtained results point to the possibility of use of the studied cement masses in the development of construction materials promoting the economic reuse of WTP sludge before discarded in landfills. (author)

  7. Energetic and exergetic assessment of a trass mill process in a cement plant

    International Nuclear Information System (INIS)

    Sogut, M.Z.; Oktay, Z.; Hepbasli, A.

    2009-01-01

    Cement production has become one of the most intensive energy industries in the world. For producing it, addition materials have been widely used in cement factories. The main objective of this study is to assess the performance of a trass mill in a cement plant based on the actual operational data using energy and exergy analysis method. In this regard, the values for energy consumption and losses throughout the production process are described. In the process, the overall exergy efficiencies are found to be slightly less than the corresponding energy efficiencies; e.g. 74% and 10.68% for energy and exergy efficiency, respectively. Using energy recovery systems, waste heat energy may be captured, while energy and exergy efficiency values can be improved to 84% and 48%, respectively. It may also be concluded that the analyses reported here will provide the investigators with knowledge about how effectively and efficiently a sector uses its energy resources.

  8. Energy audit and conservation opportunities for pyroprocessing unit of a typical dry process cement plant

    International Nuclear Information System (INIS)

    Kabir, G.; Abubakar, A.I.; El-Nafaty, U.A.

    2010-01-01

    Cement production process has been highly energy and cost intensive. The cement plant requires 8784 h per year of the total operating hours to produce 640,809 tonnes of clinker. To achieve effective and efficient energy management scheme, thermal energy audit analysis was employed on the pyroprocessing unit of the cement plant. Fuel combustion generates the bulk of the thermal energy for the process, amounting to 95.48% (4164.02 kJ/kg cl ) of the total thermal energy input. Thermal efficiency of the unit stands at 41%, below 50-54% achieved in modern plants. The exhaust gases and kiln shell heat energy losses are in significant quantity, amounting to 27.9% and 11.97% of the total heat input respectively. To enhance the energy performance of the unit, heat losses conservation systems are considered. Waste heat recovery steam generator (WHRSG) and Secondary kiln shell were studied. Power and thermal energy savings of 42.88 MWh/year and 5.30 MW can be achieved respectively. Financial benefits for use of the conservation methods are substantial. Environmental benefit of 14.10% reduction in Greenhouse gases (GHG) emissions could be achieved.

  9. Energy audit and conservation opportunities for pyroprocessing unit of a typical dry process cement plant

    Energy Technology Data Exchange (ETDEWEB)

    Kabir, G.; Abubakar, A.I.; El-Nafaty, U.A. [Chemical Engineering Programme, Abubakar Tafawa Balewa University, P. M. B. 0248, Bauchi (Nigeria)

    2010-03-15

    Cement production process has been highly energy and cost intensive. The cement plant requires 8784 h per year of the total operating hours to produce 640,809 tonnes of clinker. To achieve effective and efficient energy management scheme, thermal energy audit analysis was employed on the pyroprocessing unit of the cement plant. Fuel combustion generates the bulk of the thermal energy for the process, amounting to 95.48% (4164.02 kJ/kg{sub cl}) of the total thermal energy input. Thermal efficiency of the unit stands at 41%, below 50-54% achieved in modern plants. The exhaust gases and kiln shell heat energy losses are in significant quantity, amounting to 27.9% and 11.97% of the total heat input respectively. To enhance the energy performance of the unit, heat losses conservation systems are considered. Waste heat recovery steam generator (WHRSG) and Secondary kiln shell were studied. Power and thermal energy savings of 42.88 MWh/year and 5.30 MW can be achieved respectively. Financial benefits for use of the conservation methods are substantial. Environmental benefit of 14.10% reduction in Greenhouse gases (GHG) emissions could be achieved. (author)

  10. Estonia 2013: Energy Policies Beyond IEA Countries

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-01

    One of the fastest-growing economies in the OECD, Estonia is actively seeking to reduce the intensity of its energy system. Many of these efforts are focused on oil shale, which the country has been using for almost a century and which meets 70% of its energy demand. While it provides a large degree of energy security, oil shale is highly carbon-intensive. The government is seeking to lessen the negative environmental impact by phasing out old power plants and developing new technologies to reduce significantly CO2 emissions. The efforts on oil shale complement Estonia’s solid track record of modernising its overall energy system. Since restoring its independence in 1991, Estonia has fully liberalised its electricity and gas markets and attained most national energy policy targets and commitments for 2020. It has also started preparing its energy strategy to 2030, with an outlook to 2050. Estonia is also promoting energy market integration with neighbouring EU member states. The strengthening of the Baltic electricity market and its timely integration with the Nordic market, as well as the establishment of a regional gas market, are therefore key priorities for Estonia. Following its accession to the Organisation for Economic Co-operation and Development (OECD) in 2010, Estonia applied for International Energy Agency (IEA) membership in 2011. This review of Estonia’s energy policies is part of the IEA accession process. It analyses the energy policy challenges and opportunities facing Estonia, and provides critiques and recommendations for future policy improvements. It is intended to guide the country towards a more secure and sustainable energy future.

  11. Environmental performance reviews. Estonia

    International Nuclear Information System (INIS)

    1996-01-01

    This review of Estonia is the first environmental performance review (EPR) carried out under the auspices of the ECE Committee on Environmental Policy. This pilot ECE study builds, inter alia, on the experience gained in the preparation of pilot environmental performance reviews of Poland and Bulgaria, which were carried out in 1994-1995 by OECD in cooperation with ECE. The report focuses on capacity building; air, water, waste, and nature management; the integration of environmental and economic policies both generally and more specifically within the energy sector; and cooperation of Estonia with the international community. The review examines the current situation, recent and likely future trends, pressures, policy responses and their effectiveness. The principal conclusions and recommendations for improving Estonia's environmental performance are brought together in the concluding chapter.

  12. Phytoremediation of Cadmium and Chromium by Plants around Ardabil Cement Factory

    OpenAIRE

    Samira Hosseini; Marziyeh Mosayebi

    2016-01-01

    Heavy metals are the most important sources of non-point pollution of natural resources. Every year, thousands of these elements on a global scale enter to the soil system. The aim of this study was to investigate the phytoremediation of cadmium and chromium by plants around Ardabil Cement Factory. With field work and presence in the field of soil and plant samples need to be prepared. Statistical analysis is performed using the SPSS software. For this purpose, analysis of variance was used t...

  13. Detergent zeolite complex "Ceosil", Tallinn, Estonia

    OpenAIRE

    Stanković Mirjana S.; Pezo Lato L.

    2003-01-01

    The IGPC Engineering Department, together with the "Birac", Zvornik Engineering Department designed basic projects for detergent zeolite production, using waste flotation sand and hydrates. Several projects were completed: technological, machine, electrical, automation. On the basis of these projects, production plant in Tallinn, Estonia was constructed, with a capacity of 100,000 t/y from 1989. to 1993. This plant became the biggest producer of detergent zeolite in the world.Several goals we...

  14. Effects of pollution from oil shale mining in Estonia

    International Nuclear Information System (INIS)

    Vallner, L.; Sepp, K.

    1993-01-01

    The largest commercially exploited oil shale deposit in the world is in northeast Estonia. The accumulation of solid residues by oil shale mines and processing plants has resulted in numerous dumps and ash hills, which are polluting the environment. The groundwater and streams are highly polluted by sulphates, phenols and oil products. A dump hill of radioactive wastes poses a serious threat to the Baltic Sea. Local people suffer from diseases more often than in other regions of Estonia. (author)

  15. Improvement of cement plant dust emission by bag filter system

    Science.gov (United States)

    Wahyu Purnomo, Chandra; Budhijanto, Wiratni; Alfisyah, Muziibu; Triyono

    2018-03-01

    The limestone quarry in PT Indocement Tunggal Prakarsa (ITP) in Cirebon is considered as a complex quarry in terms of chemical composition and material hardness. From the beginning of the plant operation up to the end of 2015, the dust removal was rely on electrostatic precipitator (EP) system. Whenever limestone from specific quarry zones were incorporated into Raw Mill (RM) feed or there was an upset condition, the dust emission increased significantly. Beside higher demand of electricity, an EP system requires lower gas inlet temperature in order to remove the dust effectively which requires larger cooling water in the previous gas conditioning tower to cool down gas from 400 °C to about 100 °C. By considering the drawbacks, the EP system was replaced by a bag filter (BF) system. The BF allows higher temperature of gas inlet and it has higher dust removal efficiency. In this study, the efficiency of the two different dust removal systems is compared. The effect of process variables i.e. RM feed, kiln feed, inlet temperature and pressure, and small size particle fraction to the dust emission are studied by multivariate linier regression analysis. It is observed that the BF system can reduce significantly the dust emission from 30 to 6 mg/m3 and in the same time reducing CO2 emission by 0.24 ton/year from the electricity consumption saving.

  16. Gas development plan - Estonia

    International Nuclear Information System (INIS)

    1994-06-01

    The total supply of natural gas to Estonia is provided by the Russian company ''Lentransgas'', a 10 year contract is under negotiation. The gas transmission system is physically a part of the transmission network in the Baltic region which previously operated as an integral part of the USSR gas transmission system. The potential market is too small to justify investment in an alternative pipeline from the North Sea. The general reduction in purchasing power in the former COMECON countries has resulted in a decreased industrial production in Estonia and lead to a steep decline in natural gas consumption in all sectors except households. The Danish firm ''Dansk Olie og Naturgas A/S'' has been requested to assist the Estonian company ''AS Eesti Gaas J.S.C.'' in preparing a gas development plan for Estonia. Phase 1 of this plan aims to provide a detailed description of the status of the existing situation under the headings of gas supply and demand, transmission and distribution, economy and organization. The most important problems related to the current transition of the Estonian gas sector towards operation under market conditions are addressed, focussing on gas supply and market conditions, flow control and metering. The general organization of the gas sector in Estonia is described and possible models for future organization are discussed. Some recommendations are given and areas in need of further investigation are identified. (AB)

  17. Eliminating Rabies in Estonia

    Science.gov (United States)

    Cliquet, Florence; Robardet, Emmanuelle; Must, Kylli; Laine, Marjana; Peik, Katrin; Picard-Meyer, Evelyne; Guiot, Anne-Laure; Niin, Enel

    2012-01-01

    The compulsory vaccination of pets, the recommended vaccination of farm animals in grazing areas and the extermination of stray animals did not succeed in eliminating rabies in Estonia because the virus was maintained in two main wildlife reservoirs, foxes and raccoon dogs. These two species became a priority target therefore in order to control rabies. Supported by the European Community, successive oral vaccination (OV) campaigns were conducted twice a year using Rabigen® SAG2 baits, beginning in autumn 2005 in North Estonia. They were then extended to the whole territory from spring 2006. Following the vaccination campaigns, the incidence of rabies cases dramatically decreased, with 266 cases in 2005, 114 in 2006, four in 2007 and three in 2008. Since March 2008, no rabies cases have been detected in Estonia other than three cases reported in summer 2009 and one case in January 2011, all in areas close to the South-Eastern border with Russia. The bait uptake was satisfactory, with tetracycline positivity rates ranging from 85% to 93% in foxes and from 82% to 88% in raccoon dogs. Immunisation rates evaluated by ELISA ranged from 34% to 55% in foxes and from 38% to 55% in raccoon dogs. The rabies situation in Estonia was compared to that of the other two Baltic States, Latvia and Lithuania. Despite regular OV campaigns conducted throughout their territory since 2006, and an improvement in the epidemiological situation, rabies has still not been eradicated in these countries. An analysis of the number of baits distributed and the funding allocated by the European Commission showed that the strategy for rabies control is more cost-effective in Estonia than in Latvia and Lithuania. PMID:22393461

  18. Increase in the amount of evaporator concentrate from nuclear power plants in cemented products

    International Nuclear Information System (INIS)

    Costa, Bruna S.; Tello, Clédola C.O.

    2017-01-01

    Nuclear power plants, research centers and other nuclear facilities are sources of radioactive liquid waste generation. These wastes can come from cooling of the primary reactor system, cleaning spent pool of fuel, washing contaminated clothing, among others. One of the most used methods for the treatment of these aqueous flows is the evaporation, which generates the concentrate of the evaporator, waste classified as low and medium level of radiation. Norms determine that radioactive waste must be minimized, and that to be accepted in repositories, they must be solidified. The work sought to reduce the volume of the evaporated concentrate waste and its subsequent solidification in cement. In order to carry out the tests, the evaporator concentrate (CE) simulation solution was prepared and then dried in an oven. Subsequently, cementation of the dry material was made using cement, fluidizer, NaOH and water. After a curing time of 28 days, the compressive strength tests were made for all specimens obtained, and for the samples that obtained resistance above that required by the norm, which is 10MPa, the percentages of reject incorporated and volume reduction. The results showed that, by drying the evaporator concentrate, it was possible to reduce the volume of the waste generated by up to 27% in relation to the waste without drying, which shows that drying is an effective way to increase the incorporation of the evaporator concentrate in packaged waste

  19. Internet and Fuzzy Based Control System for Rotary Kiln in Cement Manufacturing Plant

    Directory of Open Access Journals (Sweden)

    Hanane Zermane

    2017-01-01

    Full Text Available This paper develops an Internet-based fuzzy control system for an industrial process plant to ensure the remote and fuzzy control in cement factories in Algeria. The remote process consists of control, diagnosing alarms occurs, maintaining and synchronizing different regulation loops. Fuzzy control of the kiln ensures that the system be operational at all times, with minimal downtime. Internet technology ensures remote control. The system reduces downtimes and can guided by operators in the main control room or via Internet.

  20. The enrichment of natural radionuclides in oil shale-fired power plants in Estonia – The impact of new circulating fluidized bed technology

    International Nuclear Information System (INIS)

    Vaasma, Taavi; Kiisk, Madis; Meriste, Tõnis; Tkaczyk, Alan Henry

    2014-01-01

    Burning oil shale to produce electricity has a dominant position in Estonia's energy sector. Around 90% of the overall electric energy production originates from the Narva Power Plants. The technology in use has been significantly renovated – two older types of pulverized fuel burning (PF) energy production units were replaced with new circulating fluidized bed (CFB) technology. Additional filter systems have been added to PF boilers to reduce emissions. Oil shale contains various amounts of natural radionuclides. These radionuclides concentrate and become enriched in different boiler ash fractions. More volatile isotopes will be partially emitted to the atmosphere via flue gases and fly ash. To our knowledge, there has been no previous study for CFB boiler systems on natural radionuclide enrichment and their atmospheric emissions. Ash samples were collected from Eesti Power Plant's CFB boiler. These samples were processed and analyzed with gamma spectrometry. Activity concentrations (Bq/kg) and enrichment factors were calculated for the 238 U ( 238 U, 226 Ra, 210 Pb) and 232 Th ( 232 Th, 228 Ra) family radionuclides and for 40 K in different CFB boiler ash fractions. Results from the CFB boiler ash sample analysis showed an increase in the activity concentrations and enrichment factors (up to 4.5) from the furnace toward the electrostatic precipitator block. The volatile radionuclide ( 210 Pb and 40 K) activity concentrations in CFB boilers were evenly distributed in finer ash fractions. Activity balance calculations showed discrepancies between input (via oil shale) and output (via ash fractions) activities for some radionuclides ( 238 U, 226 Ra, 210 Pb). This refers to a situation where the missing part of the activity (around 20% for these radionuclides) is emitted to the atmosphere. Also different behavior patterns were detected for the two Ra isotopes, 226 Ra and 228 Ra. A part of 226 Ra input activity, unlike 228 Ra, was undetectable in the solid

  1. Economically viable and environment-friendly hydro energy in Estonia

    International Nuclear Information System (INIS)

    Saks, Ants; Velner, Harald

    2001-01-01

    Hydro energy has been in oblivion in Estonia for about 30 years now. During the 1960s, most of Estonia's small hydropower plants were closed down, just as it was done in the whole Soviet Union. As the only larger hydro plant, the 125 MW plant in Narva, was situated on the Russian side of the Narva River, there were only two or three small hydro plants left. Even those were exploited at low capacity and mainly for heating the buildings. It was not until the 1990s that a number of enthusiasts started to re-establish the hydro plants by reconstructing old installations. The pre-feasibility study 'Hydropower in Estonia' proposed by Estonian and Swedish experts, showed that the restoration of the hydropower plants and watermills is economically feasible and technically possible if advanced technology is used. Hydropower as an alternative ('green') energy source should be used in the best technical-economical way. The first pilot plant in Estonia, the 200 kW Kamari plant was constructed in 1998 with compact-propeller units, in co-operation with Waterpumps WP Oy and ABB. Today, ten new plants have been constructed or are under construction. Hydropower plants/watermills should be reconstructed in accordance with the legislative acts on environment protection

  2. Feasibility study on energy conservation through modernization of cement plant (Sichuan Double Horse Cement Group Co. Ltd.)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigational study was conducted of possibilities of energy conservation and greenhouse effect gas emission reduction in the cement production process of Double Horse Cement Co., Mianyang City, Sichuan Province, China. Double Horse Cement adopts the wet type long kiln production system and has a production ability of approximately 1.5 million t/y. In the project, as to three production lines out of the six production lines, improvement was planned to be made of the technologies on the following: mixing of raw materials, grinding of raw materials, NSP, clinker cooler, clinker pre-grinder, high-efficiency separator, waste heat use power generation, etc. As a result of the study, it was found that the energy conservation amount obtained was 54,646 toe/y. And, the amount of greenhouse effect gas reduction was 169,086 t-CO2/y. The total fund required for this project was approximately 5.553 billion yen and the internal earning rate was 7.36% after tax. When the project is carried out, expenses vs. effects are 9.8 toe/million yen in energy conservation amount and 30.4 t-CO2/million yen in greenhouse effect gas reduction. (NEDO)

  3. Energy Efficiency Improvement and Cost Saving Opportunities for Cement Making. An ENERGY STAR Guide for Energy and Plant Managers

    Energy Technology Data Exchange (ETDEWEB)

    Galitsky, Christina; Worrell, Ernst; Galitsky, Christina

    2008-01-01

    The cost of energy as part of the total production costs in the cement industry is significant, warranting attention for energy efficiency to improve the bottom line. Historically, energy intensity has declined, although more recently energy intensity seems to have stabilized with the gains. Coal and coke are currently the primary fuels for the sector, supplanting the dominance of natural gas in the 1970s. Most recently, there is a slight increase in the use of waste fuels, including tires. Between 1970 and 1999, primary physical energy intensity for cement production dropped 1 percent/year from 7.3 MBtu/short ton to 5.3 MBtu/short ton. Carbon dioxide intensity due to fuel consumption and raw material calcination dropped 16 percent, from 609 lb. C/ton of cement (0.31 tC/tonne) to 510 lb. C/ton cement (0.26 tC/tonne). Despite the historic progress, there is ample room for energy efficiency improvement. The relatively high share of wet-process plants (25 percent of clinker production in 1999 in the U.S.) suggests the existence of a considerable potential, when compared to other industrialized countries. We examined over 40 energy efficient technologies and measures and estimated energy savings, carbon dioxide savings, investment costs, and operation and maintenance costs for each of the measures. The report describes the measures and experiences of cement plants around the wold with these practices and technologies. Substantial potential for energy efficiency improvement exists in the cement industry and in individual plants. A portion of this potential will be achieved as part of (natural) modernization and expansion of existing facilities, as well as construction of new plants in particular regions. Still, a relatively large potential for improved energy management practices exists.

  4. FUZZY LOGIC CONTROLLER AS MODELING TOOL FOR THE BURNING PROCESS OF A CEMENT PRODUCTION PLANT

    Directory of Open Access Journals (Sweden)

    P.B. Osofisan

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: A comprehensive optimisation of the cement production process presents a problem since the input variables as well as the output variables are non-linear, interdependent and contain uncertainties. To arrive at a solution, a Fuzzy Logic controller has been designed to achieve a well-defined relationship between the main and vital variables through the instrumentality of a Fuzzy Model. The Fuzzy Logic controller has been simulated on a digital computer using MATLAB 5.0 Fuzzy Logic Tool Box, using data from a local cement production plant.

    AFRIKAANSE OPSOMMING: Die omvattende optimisering van 'n proses wat sement vervaardig, word beskryf deur nie-linieêre inset- en uitsetveranderlikes wat onderling afhanklik is, en ook van onsekere aard is. Om 'n optimum oplossing te verkry, word 'n Wasigheidsmodel gebruik. Die model word getoets deur gebruik te maak van die MATLAB 5.0 Fuzzy Logic Tool Box en data vanaf 'n lokale sementvervaardigingsaanleg.

  5. Techno-economic study of CO2 capture process for cement plants. Paper no. IGEC-1-107

    International Nuclear Information System (INIS)

    Nazmul Hassan, S.M.; Douglas, P.L.; Croiset, E.

    2005-01-01

    Carbon dioxide is considered to be the major source of GHG responsible for global warming; man-made CO 2 contributes approximately 63.5% to all greenhouse gases. The cement industry is responsible for approximately 5% of global anthropogenic carbon dioxide emissions emitting nearly 900 kg of CO 2 for every 1000 kg of cement produced. Amine absorption processes, in particular the monoethanolamine (MEA) based process, is considered to be a viable technology for capturing CO 2 from low-pressure flue gas streams because of its fast reaction rate with CO 2 and low cost of raw materials compared to other amines. However, the MEA absorption process is associated with high capital and operating costs because a significant amount of energy is required for solvent regeneration and because of severe operating problems such as corrosion, solvent loss and solvent degradation. This research was motivated by the need to design, size and cost a CO 2 capture process from the cement industry. The MEA based absorption process was used as a potential technique to model CO 2 capture from cement plants. In this research four cases were considered all to reach a CO 2 purity of 98%: i) the plant operates at the highest capacity; ii) the plant operates at average load; iii) the plant operates at minimum operating capacity; and iv) switching to a lower carbon content fuel at average plant load. A comparison among the four cases were performed to determine the best operating conditions for capturing CO 2 from cement plants. A sensitivity analysis of the economics to the lean loading and percent recovery were carried out as well as the different absorber and striper tray combinations. (author)

  6. Country report: Estonia

    Science.gov (United States)

    Kaasik, Helle

    2015-12-01

    The situation of women in education, work, and research in Estonia is relatively good. Nevertheless, science (especially engineering) remains a male-dominated field. The total number of female scientists and engineers in the workforce is about two-thirds that of males. Moreover, the gender imbalance in the researcher population increases with age. Significant pay-gap and power imbalances between the genders remain both in Estonian society in general and in the fields of science and technology. In many practical situations, behavior of both men and women is still guided by gender stereotypes.

  7. Hydropower in Estonia

    International Nuclear Information System (INIS)

    Raesaar, Peeter

    1997-01-01

    Long life practice has proved that small hydropower is not a beaten track in the global energy field. Before the Second World War small hydropower was rather well developed in Estonia as well. Being neglected during the years of Soviet occupation, it is rather important to help it to regain its position in the Estonian energy system once again. Our hydropower potential is not big, but it has got a good established position as an energy saving measure. By now we have some good examples of restored hydropower stations on commercial basis to be optimistic about the future

  8. The effect of sintering time on recycled magnesia brick from kiln of the cement plant

    Science.gov (United States)

    Aji, B. B.; Rosalina, D.; Azhar; Amin, M.

    2018-01-01

    This research aim was to investigate the effect of sintering time on reuse waste of magnesia brick from the rotary kiln of the cement plant. Reuse of the magnesia brick was carried out by mixed the kaolin as the binder. Spent refractory was used as aggregate with the composition of 85% spent refractory and 15% kaolin clay, respectively. The reuse brick then was molded with the size of 5x5x5 cm using hydraulic press under a load of 10 tons in order to forms green body. Green body then dried and sintered at 1200 °C with time variation of 2 hours, 4 hours, 6 hours, 8 hours and 10 hours, respectively. Thus, for comparison reuse brick was tested to its apparent porosity, the bulk density, and Cold Crushing Strength (CCS). The effect of kaolin addition as binder was also discussed.

  9. Physical, chemical and mineralogical characterization of water treatment plant waste for use in soil-cement brick

    International Nuclear Information System (INIS)

    Pessin, L.R.; Destefani, A.Z.; Holanda, J.N.F.

    2011-01-01

    The water treatment plants (WTP) for human consumption generate huge amounts of waste in the form of sludge (sludge) that have been over the years mostly inadequately prepared in water resources and the environment. Moreover, traditional methods of disposal of waste water treatment plants commonly used are generally costly activities. An alternative method for disposal of this waste abundant is its incorporation in ceramic products. This work is focused on the physical-chemical and mineralogical composition of a sample of waste water treatment plants from the region of Campos dos Goytacazes-RJ to their use in the manufacture of soil-cement brick. Several characterization techniques were used including X-ray diffraction, X-ray fluorescence, scanning electron microscopy, picnometry, particle size analysis and plasticity. The experimental results indicate that the waste water treatment plants have the potential to be used in the manufacture of ecologic soil-cement bricks. (author)

  10. Lithological and land-use based assessment of heavy metal pollution in soils surrounding a cement plant in SW Europe.

    Science.gov (United States)

    Cutillas-Barreiro, Laura; Pérez-Rodríguez, Paula; Gómez-Armesto, Antía; Fernández-Sanjurjo, María José; Álvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino; Arias-Estévez, Manuel; Nóvoa-Muñoz, Juan Carlos

    2016-08-15

    We study the influence of phasing out a cement plant on the heavy metal (Hg, Pb and Cr) content in the surrounding soils, taking into account factors often neglected, such as contributions due to local lithology or land use. The range of total Hg was 10-144µg kg(-1), reaching up to 41 and 145mgkg(-1) for total contents of Pb and Cr, respectively. Forest soils showed higher concentration of Hg than prairie soils, indicating the importance of land use on the accumulation of volatile heavy metals in soils. In forest soils, total Hg showed a trend to decrease with soil depth, whereas in prairie soils the vertical pattern of heavy metal concentrations was quite homogeneous. In most cases, the distance to the cement plant was not a factor of influence in the soils content of the analyzed heavy metals. Total Pb and Cr contents in soils nearby the cement plant were quite similar to those found in the local lithology, resulting in enrichment factor values (EF's) below 2. This suggests that soil parent material is the main source of these heavy metals in the studied soils, while the contribution of the cement plant to Pb and Cr soil pollution was almost negligible. On the contrary, the soils surrounding the cement plant accumulate a significant amount of Hg, compared to the underlying lithology. This was especially noticeable in forest soils, where Hg EF achieved values up to 36. These results are of relevance, bearing in mind that Hg accumulation in soils may be an issue of environmental concern, particularly in prairie soils, where temporal flooding can favor Hg transformation to highly toxic methyl-Hg. In addition, the concurrence of acid soils and total-Cr concentrations in the range of those considered phytotoxic should be also stressed. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. Ways to achieve optimum utilization of waste gas heat in cement kiln plants with cyclone preheaters

    Energy Technology Data Exchange (ETDEWEB)

    Steinbiss, E

    1986-02-01

    Kiln exit gases and the exhaust gases from clinker coolers often cannot be fully utilized in drying plants. In such cases a part of the heat content of the gases should be utilized for water heating. In addition, it is possible to utilize the waste gas heat in conventional steam boilers, with which, depending on design, it is possible to generate electricity at a rate of between 10-30 kWh/t (net output). A new and promising method of utilization of waste gas heat is provided by precalcining systems with bypass, in which up to 100% of the kiln exit gases can be economically bypassed and be utilized in a steam boiler, without requiring any cooling. A development project, already started, gives information on the operational behaviour of such a plant and on the maximum energy recoverable. Alternatively, the bypass gases may, after partial cooling with air or preheater exit gas, be dedusted and then utilized in a grinding/drying plant. Furthermore, they can be used in the cement grinding process for the drying of wet granulated blastfurnace slag or other materials. For this it is not necessary to dedust the bypass gases.

  12. Leachability of radionuclides from cement solidified waste forms produced at operating nuclear power plants

    International Nuclear Information System (INIS)

    Croney, S.T.

    1985-03-01

    This study determined the leachability indexes of radionuclides contained in solidified liquid wastes from operating nuclear power plants. Different sizes of samples of cement-solidified liquid wastes were collected from two nuclear power plants - a pressurized water reactor and a boiling water reactor - to correlate radionuclide leaching from small- and full-sized (55-gallon) waste forms. Diffusion-based model analysis (ANS 16.1) of measured radionuclide leach data from both small- and full-sized samples was performed and indicate that leach data from small samples can be used to determine leachability indexes for full-sizes waste forms. The leachability indexes for cesium, strontium, and cobalt isotopes were determined for waste samples from both plants according to the models used for ANS 16.1. The leachability indexes for the pressurized water reactor samples were 6.4 for cesium, 7.1 for strontium, and 10.4 for cobalt. Leachability indexes for the boiling water reactor samples were 6.5 for cesium, 8.6 for strontium, and 11.1 for cobalt

  13. Ethnic Russian Minority in Estonia

    Directory of Open Access Journals (Sweden)

    Włodarska-Frykowska Agata

    2016-12-01

    Full Text Available The article examines the position of Russians in Estonia and their relation with ethnic Estonians. The author analyzes models of the society integration introduced by Tallinn after 1991. The results raise questions regarding language education in Estonia, the proficiency level of Estonian is getting widely known by Russians, but on the other hand, there is still a significant part of the population that cannot communicate in Estonian. Those who have a good command of Estonian tend to be better integrated and to coexist with both Estonians and Russians. Russians living in Estonia are supposed to be equally involved in social and political life of the state. The potential of all residents has to be effectively and considerably used, especially when the number of population is decreasing. The position of Russians in Estonia is a major domestic and bilateral issue in the relations with the Russian Federation.

  14. Rahvusooper taastas Estonia balli traditsiooni

    Index Scriptorium Estoniae

    2003-01-01

    Aastavahetusballi operetikavast "Suudluste valss", USA koreograaf-lavastaja Russell Adamsoni dzhässikavast "Black and White" Rahvusooperis Estonia. Kontserdisaalis mängivad tantsuks Rahvusooperi sümfooniaorkester Andres Mustoneni juhatusel ja ansambel Modern Fox

  15. Rabarocki eelsoojendus. Meeleolukas kevadkontsert Estonias

    Index Scriptorium Estoniae

    2008-01-01

    13. ja 14. juunil Järvakandis toimuva Rabarocki warm-up peost klubis Rockstars ja esimesest ETV saatest Rabarocki triloogiast 24. mail. Kevadkontserdist "Feeling Good" 26. mail Estonia kontserdisaalis

  16. Cement waste form development for ion-exchange resins and fine particles ILW of AREVA La Hague Reprocessing Plant

    International Nuclear Information System (INIS)

    Chartier, D.; Sanchez-Canet, J.; Avril, D.; Roussel, C.; Pineau, J.N.

    2015-01-01

    Wastes have been temporarily stored in dedicated silos in La Hague reprocessing plant. These wastes are to be retrieved in the near future and to be conditioned for final disposal. Some of these wastes are supposed to be encapsulated in cement matrix and, depending on the chemical composition of the waste streams, several projects are presently ongoing. The present article aims to focus on one amongst these cement encapsulation relevant projects, namely the conditioning of a mix of spent ion-exchange resins (from filtration of pool) and fine particles (insoluble fission products from spent fuel dissolution and Zircaloy and stainless steel fines from cladding shearing). The project, aims to retrieve these wastes from a silo, separate the resins and fine particles from the other waste (hulls and end pieces), in order to encapsulate the intermediate-level fines and resins in a cement matrix. The waste forms will be produced in AREVA's La Hague reprocessing plant, prior to being sent as intermediate-level waste to a long-term repository. The cement formulation developments were initially carried out at a small scale at C.E.A. Marcoule on surrogate wastes. One of the main issues that were considered was the chemical compatibility between waste and cement matrix. Indeed, swelling phenomena are sometimes reported when ion exchange resins are embedded in cement matrixes such as Portland cement. This kind of destructive phenomenon has been prevented by the use of cement containing a high amount of ground granulated blast furnace slag. The impact of the variability of ionic charge of the resins on the waste form's properties has also been addressed in order to comfort the results obtained on the reference ionic charge of resins NaNO 3 . Once the results obtained were satisfactory, intermediate scale and full scale tests were performed by AREVA. These tests have focused on adjusting the mixing process and controlling the thermal properties of the mix during setting

  17. Domestic fuel consumption in Estonia (The first half of 1993)

    International Nuclear Information System (INIS)

    Veski, Rein

    1993-01-01

    According to the data of the Estonian Statistics Department the consumption of fuels in Estonia over the period of January-June 1993 was a follows: coal 77,053 t, oil shale 7,981,840 t, fuel peat 127,376 t, peat briquette 42,041 t, firewood 154,511 solid metres, wood chip 55,648 solid metres. The consumption of fuel peat (chiefly for producing briquette) was more considerable in the town of Kohtla-Jaerve and in the districts of Paernu and Tartu where Estonia's major peat-briquette plants are located. The share of peat in the other industries has been less significant. (author)

  18. Country policy profile - Estonia. August 2015

    International Nuclear Information System (INIS)

    2015-08-01

    In Estonia, electricity from renewable sources is mainly promoted through a feed-in premium tariff. In addition, investment supports are available for specific types of renewable energy production technologies. To encourage the use of renewable energy sources for heating, investment supports are made available for the construction of CHP plants, as well as for private consumers. In transport, the use of renewable energies is currently mainly encouraged through a support scheme to promote the purchasing of electric cars that use power produced from renewable energy sources (RES Legal Europe, 2014)

  19. Country policy profile - Estonia. December 2015

    International Nuclear Information System (INIS)

    2015-12-01

    In Estonia, electricity from renewable sources is mainly promoted through a feed-in premium tariff. In addition, investment supports are available for specific types of renewable energy production technologies. To encourage the use of renewable energy sources for heating, investment supports are made available for the construction of CHP plants, as well as for private consumers. In transport, the use of renewable energies is currently mainly encouraged through a support scheme to promote the purchasing of electric cars that use power produced from renewable energy sources (RES Legal Europe, 2014)

  20. Portland cement for SO.sub.2 control in coal-fired power plants

    Science.gov (United States)

    Steinberg, Meyer

    1985-01-01

    There is described a method of removing oxides of sulfur from the emissions of fossil fuel combustion by injecting portland cement into the boiler with the fuel, the combustion air, or downstream with the combustion gases. There is also described the cement products that result from this method.

  1. Portland cement for SO/sub 2/ control in coal-fired power plants

    Science.gov (United States)

    Steinberg, M.

    1984-10-17

    A method is described for removing oxides of sulfur from the emissions of fossil fuel combustion by injecting portland cement into the boiler with the fuel, the combustion air, or downstream with the combustion gases. The cement products that result from this method is also described. 1 tab.

  2. The Constitution of the Republic of Estonia

    Index Scriptorium Estoniae

    2009-01-01

    Sisaldab ka: The Constitution of the Republic of Estonia Amendment Act. The Constitution of the Republic of Estonia Implementation Act. Act to Amend the Constitution of the Republic of Estonia for Election of Local Government Councils for Term of Four Years

  3. The Constitution of the Republic of Estonia

    Index Scriptorium Estoniae

    2005-01-01

    Raamat sisaldab ka: The Constitution of the Republic of Estonia amendment act ; The Constitution of the Republic of Estonia implementation act ; Act to amend the Constitution of the Republic of Estonia for election of local government councils for term of four years

  4. Reuse of By-Products from Ready-Mixed Concrete Plants for the Production of Cement Mortars

    Directory of Open Access Journals (Sweden)

    Monika Zervaki

    2013-06-01

    Full Text Available This study was motivated by the necessity to recycle sludge water resulting from washing out concrete mixing trucks - a problem of both environmental and economic importance for the ready-mixed concrete industry. Sludge water from ready-mixed concrete plants as well as dry sludge, which is derived from the settling of the water, are hazardous for disposal due to their high pH value (pH>11.5. In this work, cement mortars were composed using either sludge water after various treatment, or dry sludge in several ratios. The cement mortars were tested for their workability and strength development. The purpose of this experimental design was to prove that sludge water, as well as sludge in a wet or dry form, can be used in the production of mortars without degrading any of their properties.

  5. Estonia: health system review.

    Science.gov (United States)

    Lai, Taavi; Habicht, Triin; Kahur, Kristiina; Reinap, Marge; Kiivet, Raul; van Ginneken, Ewout

    2013-01-01

    This analysis of the Estonian health system reviews recent developments in organization and governance, health financing, health-care provision, health reforms and health system performance. Without doubt, the main issue has been the 2008 financial crisis. Although Estonia has managed the downturn quite successfully and overall satisfaction with the system remains high, it is hard to predict the longer-term effects of the austerity package. The latter included some cuts in benefits and prices, increased cost sharing for certain services, extended waiting times, and a reduction in specialized care. In terms of health outcomes, important progress was made in life expectancy, which is nearing the European Union (EU) average, and infant mortality. Improvements are necessary in smoking and alcohol consumption, which are linked to the majority of avoidable diseases. Although the health behaviour of the population is improving, large disparities between groups exist and obesity rates, particularly among young people, are increasing. In health care, the burden of out-of-pocket payments is still distributed towards vulnerable groups. Furthermore, the number of hospitals, hospital beds and average length of stay has decreased to the EU average level, yet bed occupancy rates are still below EU averages and efficiency advances could be made. Going forwards, a number of pre-crisis challenges remain. These include ensuring sustainability of health care financing, guaranteeing a sufficient level of human resources, prioritizing patient-centred health care, integrating health and social care services, implementing intersectoral action to promote healthy behaviour, safeguarding access to health care for lower socioeconomic groups, and, lastly, improving evaluation and monitoring tools across the health system. World Health Organization 2013 (acting as the host organization for, and secretariat of, the European Observatory on Health Systems and Policies).

  6. Model project for reduction of electric power consumption in cement plant. Report for fiscal 1999 on achievements of commissioned operation; Cement shosei plant denryoku shohi sakugen model jigyo 1999 nendo itaku gyomu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With objectives of utilizing energies efficiently and serving for environmental improvements, a model project was implemented for reduction of electric power consumption in cement plant in Vietnam. This paper reports the achievements in fiscal 1999. This project is intended to install waste heat boilers in waste gas lines in the preheating process in the cement plant, whose waste heat is recovered by steam to generate electric power by using steam turbines. The current fiscal year has executed the following activities: design of turbines, condensers, and oil units; discussions on the arrangement drawings thereof obtained from the Vietnam side; design of piping and provision of the detailed drawings thereof to the Vietnam side; planning of the electric cable routes; planning of instrumentation wiring routes; and grounding and interlocks. Results of the discussions on the proposed plant operation methods were reflected to the system design of the monitoring devices. Furthermore, the turbines were fabricated, and the associated facilities, valves, and piping materials were procured based on the detailed design. The piping materials were given pre-shipment inspections before having been transported to the site. (NEDO)

  7. Compatibility of cement with low and medium level wastes generated at nuclear power plants

    International Nuclear Information System (INIS)

    De Angelis, G.

    1987-01-01

    The incorporation of low- and medium level wastes in cement can give rise to serious problems due to the interaction between radwastes and cement components. Some troubles can occur during the first stages of the cementation process while deleterious phenomena come into evidence in the medium and long term. With the aim to improve the quality of the final waste forms a pretreatment of the waste streams is often necessary, as well as the addition of special agents to the cement matrix. The prediction of the long-term behaviour of the final products is of main importance in this research field. To this purpose some accelerated tests have been proposed, but much effort should be further devoted to the comprehension of the waste/matrix interaction. In this paper the principal waste streams are reviewed together with the possible remedies which seem to be more suitable for their cementation. Thus the qpportunity of separatly handling and solidifying different types of waste is once more supported

  8. Quality evaluation of soil-cement-plant residue bricks by the combination of destructive and non-destructive tests

    Directory of Open Access Journals (Sweden)

    Regis de C. Ferreira

    Full Text Available ABSTRACT Residues from agricultural activity can be used to improve the quality of soil-based bricks, constituting an interesting alternative for their destination. The technical quality of soil-cement-plant residue bricks was evaluated by the combination of non-destructive and destructive methods. A predominant clayey soil, Portland cement and residues of husks of both rice and Brachiaria brizantha cv. Marandu (0, 10, 20, 30 and 40%, in mass, in substitution to the 10% cement content were used. The bricks were submitted to destructive (water absorption and compressive strength and nondestructive (ultrasound tests for their physical and mechanical characterization. Results from both destructive and non-destructive tests were combined to determine the quantitative parameter named “anisotropic resistance” in order to evaluate the quality of the bricks. The addition that promoted best technical quality was 10% residue content, regardless of the residue type. The anisotropic resistance proved to be adequate for the technical quality evaluation of the bricks.

  9. Evaluation of physical stability and leachability of Portland Pozzolona Cement (PPC) solidified chemical sludge generated from textile wastewater treatment plants

    International Nuclear Information System (INIS)

    Patel, Hema; Pandey, Suneel

    2012-01-01

    Highlights: ► Stabilization/solidification of chemical sludge from textile wastewater treatment plants using Portland Pozzolona Cement (PPC) containing fly ash. ► Physical engineering (compressive strength and block density) indicates that sludge has potential to be reused for construction purpose after stabilization/solidification. ► Leaching of heavy metals from stabilized/solidified materials were within stipulated limits. ► There is a modification of microstructural properties of PPC with sludge addition as indicated by XRD and SEM patterns. - Abstract: The chemical sludge generated from the treatment of textile dyeing wastewater is a hazardous waste as per Indian Hazardous Waste Management rules. In this paper, stabilization/solidification of chemical sludge was carried out to explore its reuse potential in the construction materials. Portland Pozzolona Cement (PPC) was selected as the binder system which is commercially available cement with 10–25% fly ash interground in it. The stabilized/solidified blocks were evaluated in terms of unconfined compressive strength, block density and leaching of heavy metals. The compressive strength (3.62–33.62 MPa) and block density (1222.17–1688.72 kg/m 3 ) values as well as the negligible leaching of heavy metals from the stabilized/solidified blocks indicate that there is a potential of its use for structural and non-structural applications.

  10. Natural radioactivity of raw materials and products of cement manufacturing and of power plant fly ashes

    International Nuclear Information System (INIS)

    Gallyas, Miklos

    1984-01-01

    The natural radioactivity was investigated for several building materials used in Hungary, including cement, concrete, glasses, fine ceramic products, insulation materials, and also for some industrial wastes utilized as building material aggregates like slags, fly ashes etc., from their radiation health aspect. The dose commitments of the population from building materials standardized in several countries are presented. The 232 Th, 226 Ra, and 40 K contents of building materials were measured by gamma spectrometry, using NaI/Tl/scintillation detectors. The results were used to qualify cement materials and fly ash aggregates according to their origin in Hungary, from the point of view of their natural radioactivity. It was concluded that the radioactivity level of the majority of Hungarian cements are below the adopted international standards. (R.P.)

  11. Main components of PM10 in an area influenced by a cement plant in Catalonia, Spain: Seasonal and daily variations.

    Science.gov (United States)

    Rovira, Joaquim; Sierra, Jordi; Nadal, Martí; Schuhmacher, Marta; Domingo, José L

    2018-05-01

    Particulate matter (PM) composition has a key role in a wide range of health outcomes, such as asthma, chronic obstructive pulmonary disease, lung cancer, cardiovascular disease, and death, among others. Montcada i Reixac, a municipality located in the Barcelona metropolitan area (Catalonia, Spain), for its location and orography, is an interesting case- study to investigate air pollution. The area is also characterized by the presence of different industrial emission sources, including a cement factory and a large waste management plant, as well as an intense traffic. In this study, PM 10 levels, trace elements, ions, and carbonaceous particles were determined for a long time period (2013-2016) in this highly polluted area. PM 10 samples were collected during six consecutive days in two campaigns (cold and warm) per year. A number of elements (As, Ba, Be, Bi, Ca, Cd, Ce, Co, Cr, Cs, Cu, Dy, Er, Eu, Fe, Ga, Gd, Ge, Hf, Hg, Ho, K, La, Li, Hg, Mg, Mn, Mo, Nb, Nd, Ni, Pb, Pr, Rb, Sb, Sc, Se, Sm, Sn, Sr, Tb, Th, Ti, Tl, U, V, W, Y, Yb, and Zr), ions (Cl - , SO 4 2- , NO 3 - , and NH 4 + ), and carbonaceous content (total carbon, organic plus elemental carbon, and CO 3 2- ), were analysed. These data were used to identify the PM 10 main components: mineral matter, sea spray, secondary inorganic aerosols, organic matter plus elemental carbon, trace elements or indeterminate fraction. Although a clear seasonality (cold vs. warm periods) was found, there were no differences between working days and weekends. Obviously, the cement plant influences the surrounding environment. However, no differences in trace elements related with the cement plant activity (Al, Ca, Ni and V) between weekdays and weekends were noted. However, some traffic-related elements (i.e., Co, Cr, Mn, and Sb) showed significantly higher concentrations in weekdays. Copyright © 2018 Elsevier Inc. All rights reserved.

  12. Captive power plant selection for pakistan cement industry in perspective of current energy crises: a fuzzy-ahp approach

    International Nuclear Information System (INIS)

    Ali, H.M.; Sultan, A.; Rana, B.B.

    2017-01-01

    Based on the prevailing energy crisis, it is reasonable for the Cement industry of Pakistan to look for alternate sources of electricity generation. The decision of selecting a CPP (Captive Power Plant) depends on a broad variety of parameters which may be conflicting to each other. A comparative evaluation of these CPP's should be helpful for industry, particularly if the applied methodology can handle with the real world ambiguities and imprecisions associated with the data pools and expert opinions. This paper utilizes an F-AHP (Fuzzy Analytical Hierarchy Process) based multi-attribute framework to prioritize the affecting parameters and assign rankings to the CPP alternatives. The CPP's recommended by experts for this study are RDF-CPP (Refused Derived Fuel CPP), CF-CPP (Coal Fired CPP) and WHR-CPP (Waste Heat Recovery CPP). The factors affecting the decision of selecting the optimum CPP are prioritized by the experts using our F-AHP approach. Real world quantitative data is extracted from different online resources and financial reports of cement companies in Pakistan. The F-AHP model is flexible enough to deal with a variety of inputs including qualitative scales, crisp values and standard fuzzy numbers. The model is solved and a sensitivity analysis is performed in respective software. This study shows that non-conventional CPPs are highly demanded for cement industry in Pakistan and while selecting these CPPs, management gives high priority to factors like 'automation' and 'environment' whereas associated "initial cost"is not given much weight in decision making. In concluding ranking list, WHR-CPP is at the top and CF-CPP is at the bottom. This study may facilitate decision makers of cement industry in Pakistan and international CPP manufacturers alike in their forthcoming strategic decisions. (author)

  13. Use of wood as an alternative fuel to coal and natural gas at the Holnam Cement Plant, north of LaPorte, Colorado

    Science.gov (United States)

    Kurt H. Mackes

    2001-01-01

    The Holnam Company currently operates a cement plant north of Laporte, CO. The plant is attempting to use wood as an alternate fuel to coal and natural gas. The principal objective of this project is to investigate the extended use of wood as an alternate fuel at the plant. Tests conducted at Holnam indicate that wood is suitable for use at the plant and Holnam could...

  14. Cementation process study

    International Nuclear Information System (INIS)

    Park, H.H.; Han, K.W.; Ahn, S.J.; Choi, K.S.; Lee, M.W.; Ryu, Y.K.

    1985-01-01

    In the cementation process study, in 1984, design of the waste treatment simulator was finished for the first step. We can experience not only the operation of solidification system but the design and construction of comming large scale plant through the design of cementation process. (Author)

  15. Basic survey project for Joint Implementation, etc. Feasibility study on the modernization of cement plant in Republic of Kazakhstan

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing greenhouse effect gas emissions, a project was studied for the modernization of a cement plant in the Republic of Kazakhstan. In the Semipalatinsk cement plant, an old wet type kiln is being used which is much consuming in energy and low in productivity. By replacing this kiln with the NSP dry type kiln, expected were the enhancement of efficiency, energy conservation, and reduction in greenhouse effect gas emissions. Further, it was planned that four lines for raw material production and four lines for clinker combustion are tied together to make it one, and the ball mill is replaced with the low power-consuming type roller mill. By this project, the energy consumption will decrease by 96,000 t/y in coal and 2,095,500 kWh/y in electric power, which is a decrease of approximately 39% from the energy consumption before the project being worked out. Moreover, as to greenhouse effect gases, there are no changes in CO2 gas emissions from limestone, but CO2 gas emissions from coal decrease by 216.960 t/y, which is a decrease of 28.5% from that before the project being worked out. (NEDO)

  16. Technical assistance for EBRD-PMU, Estonia

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    The EBRD Energy Sector Emergency Loan to Estonia has resulted in numerous benefits for the Estonian Energy Sector and the Estonian Society and the locals as well as the end users have developed themselves tremendously during the project. The substantial economic, environmental and energy saving effects of the loan project have been: Energy savings and improved energy efficiency in the electricity grid, the district heating networks, the district heating consumer installations, the energy production plants in terms of rehabilitated or converted boilers and burners, industrial consumer installations. The energy efficiency improvements have resulted in energy savings between 5% and 30%; Conversion of boilers from expensive imported heavy fuel oil to indigenous fuels such as peat and wood. The results are higher supply security, improved boiler efficiency, reduced emissions and reduced operation and maintenance costs; Rehabilitated district heating networks resulted in reduced heat and water losses, improved operation of installations and reduced maintenance costs; Rehabilitated electricity grids with fewer break-downs, reduced maintenance costs and improved energy efficiency as results; Improved operation of the larger energy utilities resulting in lower operational costs, improved dispatch of the energy systems and speedier actions in case of break-downs. The economic indicators, pay-back time and Internal Rate of Return show that a large number of the projects have had a substantial impact on the Estonian economy and that the projects have been sound investments. The recommendations for the local completion of the work in Estonia are: The Juri boiler plant should be carefully attended to by the PMU and the Estonian authorities. (Abstract Truncated)

  17. First PET scans in Estonia

    International Nuclear Information System (INIS)

    Nazarenko, Sergei

    2003-01-01

    First PET scans in Estonia were performed on 25th November 2002 in North Estonia Regional Hospital, Tallinn. Six patients with melanoma underwent scanning with FDG. This event was a result of thorough extensive preparations first started in 2000 during the European Association of Nuclear Medicine congress in Paris. During the congress first contacts were made with providers of mobile PET units. At the same time negotiations were begun with potential FDG suppliers. For the introduction of PET in Estonia mobile truckmounted scanning technology was chosen due to low level of initial investments. Of particular importance was also availability of maintenance personnel from the device providers. A significant prerequisite was potential availability of FDG from the neighbourhood - Finland and Sweden. The latter avoided the necessity for investments into local cyclotrons and local FDG production. For the first scanning experience the dedicated truckmounted PET-camera Accel, Siemens was brought by the International Hospital Group (IHG, Amersfoort, Netherlands). The device arrived by ferry from Stockholm to Tallinn harbour at 10 o'clock in the morning and left by ferry for Helsinki at 23 o'clock. The team-on-truck consisted of one technician for device operation, two drivers and two company representatives. North Estonia Regional Hospital provided three additional technicians for patient preparation and FDG injection, one nuclear medicine doctor and one specialist of biomedical engineering and medical physics. The FDG was provided by MAP Medical Technologies, Schering, Helsinki, Finland. The shipments were made by air. This was possible due to small distance between Tallinn and Helsinki of approximately 80 km due to the regular flight connections between the two cities. The FDG was shipped in two lots with a time interval of 4 hours. The patient selection was based on clinical and histopathology data. In all six patients the exam was justified for detailied staging and

  18. Cement matrix for immobilisation of spent anionic resins in borate form arising from nuclear power plants

    International Nuclear Information System (INIS)

    Sathi Sasidharan, N.; Deshingkar, D.S.; Wattal, P.K.

    2005-11-01

    In water cooled reactors boron is added as boric acid to control nuclear reactor power levels. The boric acid concentration in coolant/moderator water, is controlled by using strongly basic anionic resins in borate (H 2 BO 3 - ) form. The spent anionic resins in borate form contain 131 Iodine, 99 Technitium and 137 Cesium activities. Direct immobilisation of anionic resins in borate form in Ordinary Portland Cement (OPC) and Slag Cement was investigated using vermiculite, bentonite, calcium oxide and silica as admixtures. The cumulative fraction of 137 Cesium leached and 137 Cesium leach rate for slag cement matrix were 0.029 and 0.00064 g.cm 2 .d -1 respectively for 95 days of leaching. The volume reduction factor achieved by direct immobilisation of anionic resins in borate form was 0.48. Immobilisation of pyrolysis residues from these resins in OPC matrix was also studied. Leaching of matrix blocks was carried out for 180 days in DM water to optimise the matrix formulation. The cumulative fraction of 137 Cesium leached and 137 Cesium leach rate were 0.076 and 0.00054 respectively for 180 days leaching. The volume reduction factor achieved by immobilisation of pyrolysis residues was 2.4. OPC is non compatible to cationic resins loaded with alkali in absence of specific admixtures. Hence cationic resins loaded with alkali and anionic resins in borate form can not be immobilised together. (author)

  19. The development of plant for reprocessing of radioactive waste from atomic power plant decommissioning with cementation method

    International Nuclear Information System (INIS)

    Barinov, A.S.; Volkov, A.S.; Dmitriev, S.A.; Flit, V.U.; Chebishev, V.M.

    1993-01-01

    The primary purpose for developing this facility is to design a universal mixer, which carries out the process of cementation either in continuous or in batch mode under close control. The second aim for development is to simplify, as much as possible, the process of decontamination of the mixer. The mixer is developed on the base of the apparatus and consists of the inductor of the apparatus with the vorticity layer, where magnet windings which produce a rotating magnetic field are placed

  20. Energy from Waste and Biomass - ALTENER Conference held in Estonia

    International Nuclear Information System (INIS)

    Roos, Inge

    1999-01-01

    On November 9-10, 1998 ALTENER Conference Energy from Waste and Biomass took place in the hotel Pirita, Tallinn, Estonia. The Conference was organized by the Swedish National Energy Administration in co-operation with the FEMOPET Estonia and the South Jutland University Centre, Biomass Institute (Denmark). The main topics of the Conference were: collecting biogas from landfall, biogas from municipal sewage treatment, biogas from animal manure, waste heat, biomass from the pulp industry and the sawmill, biomass from forestry, biomass for local and district heating. More than 200 delegates from 14 countries participated in this event. A poster exhibition and two study tours to Paeaeskuela Landfill Plant and Jueri Boiler House were organised too. (author)

  1. Assessment of operators' mental workload using physiological and subjective measures in cement, city traffic and power plant control centers.

    Science.gov (United States)

    Fallahi, Majid; Motamedzade, Majid; Heidarimoghadam, Rashid; Soltanian, Ali Reza; Miyake, Shinji

    2016-01-01

    The present study aimed to evaluate the operators' mental workload (MW) of cement, city traffic control and power plant control centers using subjective and objective measures during system vital parameters monitoring. This cross-sectional study was conducted from June 2014 to February 2015 at the cement, city traffic control and power plant control centers. Electrocardiography and electroencephalography data were recorded from forty males during performing their daily working in resting, low mental workload (LMW), high mental workload (HMW) and recovery conditions (each block 5 minutes). The NASA-Task Load Index (TLX) was used to evaluate the subjective workload of the operators. The results showed that increasing MW had a significant effect on the operators subjective responses in two conditions ([1,53] = 216.303, P < 0.001, η2 = 0.803). Also,the Task-MW interaction effect on operators subjective responses was significant (F [3, 53] = 12.628,P < 0.001, η2 = 0.417). Analysis of repeated measures analysis of variance (ANOVA) indicated that increasing mental demands had a significant effect on heart rate, low frequency/high frequency ratio, theta and alpha band activity. The results suggested that when operators' mental demands especially in traffic control and power plant tasks increased, their mental fatigue and stress level increased and their mental health deteriorated. Therefore, it may be necessary to implement an ergonomic program or administrative control to manage mental probably health in these control centers. Furthermore, by evaluating MW, the control center director can organize the human resources for each MW condition to sustain the appropriate performance as well as improve system functions.

  2. Assessment of operators’ mental workload using physiological and subjective measures in cement, city traffic and power plant control centers

    Science.gov (United States)

    Fallahi, Majid; Motamedzade, Majid; Heidarimoghadam, Rashid; Soltanian, Ali Reza; Miyake, Shinji

    2016-01-01

    Background: The present study aimed to evaluate the operators’ mental workload (MW) of cement, city traffic control and power plant control centers using subjective and objective measures during system vital parameters monitoring. Methods: This cross-sectional study was conducted from June 2014 to February 2015 at the cement, city traffic control and power plant control centers. Electrocardiography and electroencephalography data were recorded from forty males during performing their daily working in resting, low mental workload (LMW), high mental workload (HMW) and recovery conditions (each block 5 minutes). The NASA-Task Load Index (TLX) was used to evaluate the subjective workload of the operators. Results: The results showed that increasing MW had a significant effect on the operators subjective responses in two conditions ([1,53] = 216.303, P < 0.001, η2 = 0.803). Also,the Task-MW interaction effect on operators subjective responses was significant (F [3, 53] = 12.628,P < 0.001, η2 = 0.417). Analysis of repeated measures analysis of variance (ANOVA) indicated that increasing mental demands had a significant effect on heart rate, low frequency/high frequency ratio, theta and alpha band activity. Conclusion: The results suggested that when operators’ mental demands especially in traffic control and power plant tasks increased, their mental fatigue and stress level increased and their mental health deteriorated. Therefore, it may be necessary to implement an ergonomic program or administrative control to manage mental probably health in these control centers. Furthermore, by evaluating MW, the control center director can organize the human resources for each MW condition to sustain the appropriate performance as well as improve system functions. PMID:27386425

  3. Financial Participation of Employees in Estonia

    DEFF Research Database (Denmark)

    Eamets, Raul; Mygind, Niels; Spitsa, Natalia

    2006-01-01

    Presently, legal regulation of participation of employees - financial participation as well as participation in decision-making - is not well developed in Estonia. On the one hand, it is due to the fact that no tradition of employee participation could have been formed after Estonia became...

  4. Cermet cements.

    Science.gov (United States)

    McLean, J W

    1990-01-01

    Cermet ionomer cements are sintered metal/glass powders, which can be made to react with poly(acids). These new cements are significantly more resistant to abrasion than regular glass ionomer cements and are widely accepted as core build-up materials and lining cements. They can strengthen teeth and provide the clinician with an opportunity to treat early dental caries.

  5. Feasibility Assessment of CO2 Capture Retrofitted to an Existing Cement Plant : Post-combustion vs. Oxy-fuel Combustion Technology

    NARCIS (Netherlands)

    Gerbelová, Hana; Van Der Spek, Mijndert; Schakel, Wouter

    2017-01-01

    This research presents a preliminary techno-economic evaluation of CO2 capture integrated with a cement plant. Two capture technologies are evaluated, monoethanolamine (MEA) post-combustion CO2 capture and oxy-fuel combustion. Both are considered potential technologies that could contribute to

  6. Cost-benefit analysis of using sewage sludge as alternative fuel in a cement plant: a case study.

    Science.gov (United States)

    Nadal, Martí; Schuhmacher, Marta; Domingo, José L

    2009-05-01

    To enforce the implementation of the Kyoto Protocol targets, a number of governmental/international institutions have launched emission trade schemes as an approach to specify CO(2) caps and to regulate the emission trade in recent years. These schemes have been basically applied for large industrial sectors, including energy producers and energy-intensive users. Among them, cement plants are included among the big greenhouse gas (GHG) emitters. The use of waste as secondary fuel in clinker kilns is currently an intensive practice worldwide. However, people living in the vicinity of cement plants, where alternative fuels are being used, are frequently concerned about the potential increase in health risks. In the present study, a cost-benefit analysis was applied after substituting classical fuel for sewage sludge as an alternative fuel in a clinker kiln in Catalonia, Spain. The economical benefits resulting in the reduction of CO(2) emissions were compared with the changes in human health risks due to exposure to polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and carcinogenic metals (As, Cd, Co, and Cr) before and after using sewage sludge to generate 20% of the thermal energy needed for pyro-processing. The exposure to PCDD/Fs and metals through air inhalation, soil ingestion and dermal absorption was calculated according to the environmental levels in soil. The carcinogenic risks were assessed, and the associated cost for the population was estimated by considering the DG Environment's recommended value for preventing a statistical fatality (VPF). In turn, the amount of CO(2) emitted was calculated, and the economical saving, according to the market prices, was evaluated. The use of sewage sludge as a substitute of conventional energy meant a probability cancer decrease of 4.60 for metals and a cancer risk increase of 0.04 for PCDD/Fs. Overall, a net reduction of 4.56 cancers for one million people can be estimated. The associated economical

  7. Mesothelioma incidence in the neighbourhood of an asbestos-cement plant located in a national priority contaminated site

    Directory of Open Access Journals (Sweden)

    Lucia Fazzo

    2014-12-01

    Full Text Available BACKGROUND: An epidemic of asbestos-related disease is ongoing in most industrialized countries, mainly attributable to past occupational exposure but partly due to environmental exposure. In this perspective, the incidence of pleural mesothelioma close to a former asbestos-cement plant in a national contaminated site was estimated. METHODS: The census-tracts interested by atmospheric dispersion of facilities in the contaminated site were identified. Two subareas with different estimated environmental asbestos impact were distinguished. An ecological study at micro-geographic level was performed. The standardized incidence ratios (SIR for study area and the two subareas, in comparison with region and municipality were computed. The standardized incidence rate ratio (IRR between the two subareas was computed. RESULTS: Mesothelioma incidence in the study area was increased: 46 cases were observed with respect to 22.23 expected (SIR: 2.02. The increase was confirmed in analysis considering only the subjects without an occupationally exposure to asbestos: 19 cases among men (SIR = 2.48; 95% CI: 1.49-3.88; 11 case among women (SIR = 1.34; 95% CI: 0.67-2.40. The IRR between the two subareas is less than one in overall population considering all age-classes and of 3 fold (IRR = 3.14, 95% CI: 0.65-9.17 in the age-classes below 55 years. CONCLUSIONS: The findings indicate an increased incidence of pleural mesothelioma in the neighbourhood of asbestos-cement plant, and a possible etiological contribution of asbestos environmental exposure in detected risks.

  8. Saltstone: cement-based waste form for disposal of Savannah River Plant low-level radioactive salt waste

    International Nuclear Information System (INIS)

    Langton, C.A.

    1984-01-01

    Defense waste processing at the Savannah River Plant will include decontamination and disposal of approximately 400 million liters of waste containing NaNO 3 , NaOH, Na 2 SO 4 , and NaNO 2 . After decontamination, the salt solution is classified as low-level waste. A cement-based waste form, saltstone, has been designed for disposal of Savannah River Plant low-level radioactive salt waste. Bulk properties of this material have been tailored with respect to salt leach rate, permeability, and compressive strength. Microstructure and mineralogy of leached and unleached specimens were characterized by SEM and x-ray diffraction analyses. The disposal system for the DWPF salt waste includes reconstitution of the crystallized salt as a solution containing 32 wt % solids. This solution will be decontaminated to remove 137 Cs and 90 Sr and then stabilized in a cement-based waste form. Laboratory and field tests indicate that this stabilization process greatly reduces the mobility of all of the waste constitutents in the surface and near-surface environment. Engineered trenches for subsurface burial of the saltstone have been designed to ensure compatibility between the waste form and the environment. The total disposal sytem, saltstone-trench-surrounding soil, has been designed to contain radionuclides, Cr, and Hg by both physical encapsulation and chemical fixation mechanisms. Physical encapsulation of the salts is the mechanism employed for controlling N and OH releases. In this way, final disposal of the SRP low-level waste can be achieved and the quality of the groundwater at the perimeter of the disposal site meets EPA drinking water standards

  9. Study of air pollution with cement dust and its effect on plants cover in the surrounding area of Tartous cement factory

    International Nuclear Information System (INIS)

    Meslmani, Y.; Al-Oudat, M.; Al-Kharfan, K.

    2000-06-01

    Cement dust fall, concentration of total suspended particulate (TSP) and particulate less than 10 micron (PM10), were measured in different sites in the surrounding area of Tartus cement factory. The effects of cement dust emission on the growth of olive trees have been investigated. The results show that the dust fall, TSP and PM10 concentration were higher than The World Health Organization (WHO) standard at the factory site as well as in the surrounding area within 3 to 4 km in the diameter.The study shows that, the cement dust fall decreases the growth of olive trees by 34.5, 33 and 21% regarding the I, II, III sites respectively in comparison with the reference site. The branch length, branch weight, amount of chlorophyll and leaves quantity were decreased significantly. The mean weight of dust fall were 34.5, 26.4 and 10.9 g/m 2 on the leaves area at the site I, II, III respectively while the reference site has a value of 1.9 g/m 2 .(Author)

  10. Study of air pollution with cement dust and its effect on plants cover in the surrounding area of Tartous cement factory

    Energy Technology Data Exchange (ETDEWEB)

    Meslmani, Y; Al-Oudat, M; Al-Kharfan, K [Atomic Energy Commission, Damascus (Syrian Arab Republic). Dept. of Protection and Safety

    2000-06-01

    Cement dust fall, concentration of total suspended particulate (TSP) and particulate less than 10 micron (PM10), were measured in different sites in the surrounding area of Tartus cement factory. The effects of cement dust emission on the growth of olive trees have been investigated. The results show that the dust fall, TSP and PM10 concentration were higher than The World Health Organization (WHO) standard at the factory site as well as in the surrounding area within 3 to 4 km in the diameter.The study shows that, the cement dust fall decreases the growth of olive trees by 34.5, 33 and 21% regarding the I, II, III sites respectively in comparison with the reference site. The branch length, branch weight, amount of chlorophyll and leaves quantity were decreased significantly. The mean weight of dust fall were 34.5, 26.4 and 10.9 g/m{sup 2} on the leaves area at the site I, II, III respectively while the reference site has a value of 1.9 g/m{sup 2}.(Author)

  11. ALARA Design Review for the Resumption of the Plutonium Finishing Plant (PFP) Cementation Process Project Activities

    CERN Document Server

    Dayley, L

    2000-01-01

    The requirements for the performance of radiological design reviews are codified in 10CFR835, Occupational Radiation Protection. The basic requirements for the performance of ALARA design reviews are presented in the Hanford Site Radiological Control Manual (HSRCM). The HSRCM has established trigger levels requiring radiological reviews of non-routine or complex work activities. These requirements are implemented in site procedures HNF-PRO-1622 and 1623. HNF-PRO-1622 Radiological Design Review Process requires that ''radiological design reviews [be performed] of new facilities and equipment and modifications of existing facilities and equipment''. In addition, HNF-PRO-1623 Radiological Work Planning Process requires a formal ALARA Review for planned activities that are estimated to exceed 1 person-rem total Dose Equivalent (DE). The purpose of this review is to validate that the original design for the PFP Cementation Process ensures that the principles of ALARA (As Low As Reasonably Achievable) were included...

  12. Association between PM10 concentrations and school absences in proximity of a cement plant in northern Italy.

    Science.gov (United States)

    Marcon, Alessandro; Pesce, Giancarlo; Girardi, Paolo; Marchetti, Pierpaolo; Blengio, Gianstefano; de Zolt Sappadina, Simona; Falcone, Salvatore; Frapporti, Guglielmo; Predicatori, Francesca; de Marco, Roberto

    2014-03-01

    Dusts are one of the main air pollutants emitted during cement manufacturing. A substantial part of these are breathable particles that are less than 10 μm in diameter (PM10), which represent a potential threat for the health of the exposed population. This study aimed at evaluating the short-term effects of PM10 concentrations on the health of children, aged 6-14 years, who attended the schools in Fumane (Italy), in proximity (1.2 km) to a large cement plant. School absenteeism was used as a proxy indicator of child morbidity. Time series of daily school absences and PM10 concentrations were collected for 3 school-years from 2007 to 2010 (541 school-days, 462 children on average). The associations between PM10 concentrations and school absence rates in the same day (lag0) and in the following 4 days (lag1 to lag4) were evaluated using generalised additive models, smoothed for medium/long term trends and adjusted for day of the week, influenza outbreaks, daily temperature and rain precipitations. The average concentration of PM10 in the period was 34 (range: 4-183) μg/m(3). An average 10 μg/m(3) increase of PM10 concentration in the previous days (lag0-4) was associated with a statistically significant 2.5% (95%CI: 1.1-4.0%) increase in the rate of school absences. The highest increase in the absence rates (2.4%; 95%CI: 1.2-3.5%) was found 2 days after exposure (lag2). These findings provide epidemiological evidence of the acute health effects of PM10 in areas with annual concentrations that are lower than the legal European Union limit of 40 μg/m(3), and support the need to establish more restrictive legislative standards. Copyright © 2013 Elsevier GmbH. All rights reserved.

  13. Sakslased kiidavad Estonia huku filmi / Tuuli Koch

    Index Scriptorium Estoniae

    Koch, Tuuli

    2003-01-01

    Saksamaal Berliinis esilinastus 13. oktoobril poliitiline põnevusfilm "Balti torm" ("Baltic Storm"), mis kujutab parvlaev "Estonia" hukku. Eestisse filmi toomisega tegelev produtsent Mati Sepping peab sakslaste kommentaare filmile headeks

  14. Jutta Rabe teeb Estonia hukust uue filmi

    Index Scriptorium Estoniae

    2002-01-01

    Eile alustas Saksa ajakirjanik Jutta Rabe oma filmi "Baltic Storm" võtetega, mis kujutab parvlaev "Estonia" hukku venelaste vandenõu tulemusena. Peale Rabe on stsenaristid veel saksa advokaat Henning Witte ja rootslane Kaj Holmberg

  15. Erastaja varjas osalusi Rail Estonias / Anneli Ammas

    Index Scriptorium Estoniae

    Ammas, Anneli, 1962-

    2001-01-01

    Eesti Päevalehe andmeil on Eesti Raudtee erastamiskonkursi võitnud Rail Estonia suurim aktsionär John Orrison. Vt. samas "Töötasid koos Bushi kabinetis". Väidetavalt salgab J. Orrison Tony Massei tundmise maha

  16. Climate change studies in Estonia

    International Nuclear Information System (INIS)

    Kallaste, Tiit; Kuldna, Piret

    1998-01-01

    The present collection of papers was compiled on the basis of research papers written by Estonian scientists during the United Nations Environment Programme and Global Environment Facility initiated climate change programme Country Case Study on Climate Change Impacts and Adaptations Assessments. The Estonian country case study was finally approved by UNEP/GEF in February 1996, practical work started in September. The priorities for Estonia in the study of global climate change impacts and adaptation have been in the following areas of interest: agriculture, water resources, forestry, the Baltic Sea and Estonian coast, also historical climate and socioeconomic background together with the biggest producer of greenhouse gases, the energy sector. Those areas have been studied more carefully during the one and half year period of the project

  17. Estonia

    Index Scriptorium Estoniae

    2000-01-01

    Järg 2001 nr. 1 lk. 25-31, nr. 2 lk. 41-47, nr. 3 lk. 29-37, 2002 nr. 1 lk. 16-23, nr. 2 lk. 39-47, nr. 3 lk. 25-33, 2003 nr. 1 lk. 23-31, nr. 2 lk. 33-41, nr. 3 lk. 31-39, 2004 nr. 1 lk. 31-39, nr. 2 lk. 35-41; 2005 nr. 1 lk. 37-44, nr. 2 lk. 43-51, nr. 3 lk. 23-27. Ülevaade Eesti peamistest majandusnäitajatest. Lisa: Tabel majandusnäitajatega

  18. Study of Compressive Strength of Concrete with Coal Power Plant Fly Ash as Partial Replacement of Cement and Fine Aggregate

    Directory of Open Access Journals (Sweden)

    FAREED AHMED MEMON

    2010-10-01

    Full Text Available This research study comprises of concrete cubes made with Ordinary Portland Cement and with different configurations of fly ash by replacing cement and fine aggregate. To achieve the aim of this study, total 81 concrete cubes were cast. Among 81 cubes, 9 cubes were made with normal concrete, 36 cubes were made by replacing 25%, 50%, 75% and 100% of fine aggregate with fly ash and 36 cubes were made by replacing 10%, 25%, 50%, and 75% of cement with fly ash. The cubes were 6\\" x 6\\" in cross-section, and the mix design was aimed for 5000 psi. After proper curing of all 81 cubes, they were tested at 3, 7 and 28 days curing age. The cubes were tested in Forney Universal Testing Machine. By analyzing the test results of all the concrete cubes, the following main findings have been drawn. The compressive strength of concrete cubes made by replacing 100 % fine aggregate by fly ash was higher than the concrete cubes made with Ordinary Portland Cement at all 3, 7 and 28 days curing ages. On the other hand, the compressive strength of concrete cubes made by replacing 10 % and 25 % cement by fly ash was slightly lower than the concrete cubes made with Ordinary Portland Cement at all curing ages, whereas, the compressive strength of concrete cubes made by replacing 50 % and 75 % of cement by fly ash were quite lower than the concrete cubes made with Ordinary Portland Cement at all curing ages.

  19. Impact of fuel selection on the environmental performance of post-combustion calcium looping applied to a cement plant

    NARCIS (Netherlands)

    Schakel, Wouter; Hung, Christine Roxanne; Tokheim, Lars Andre; Strømman, Anders Hammer; Worrell, Ernst; Ramírez, Andrea

    2018-01-01

    Calcium looping CO2 capture is a promising technology to reduce CO2 emissions from cement production. Coal has been seen as a logical choice of fuel to drive the calcium looping process as coal is already the primary fuel used to produce cement. This study assesses the impact of using different

  20. Feasibility study on energy conservation and reduction of CO2 emissions using RDF (refused derived fuel) at a Chinese cement plant

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The feasibility study was conducted on a project in China for energy saving and greenhouse gas emission reduction by introducing the energy-saving and alternative energy technologies in cement plants. The cement plant selected for the feasibility study is Shanghai Plant of Shanghai Allied Cement Co., Ltd. (SAC), for RDF receive and supply facility, chlorine bypass facility, exhaust heat power generation facility and RDF production facility. The study results indicate that the exhaust power generation can save energy of 4,700 tons/y as crude, or energy saving rate of 25.5%, and that replacing part of coal by RDF and exhaust power generation can reduce CO2 emissions by 25,500 and 18,500 tons/y, respectively. For the investment recovery, it is estimated that the investment can be recovered in 9 years, and the project value is 81.399 million Yuan with the initial investment and project profit in each year discounted to the present value. These results fail to satisfy the SAC's investment standards. (NEDO)

  1. Feasibility study on energy conservation and reduction of CO2 emissions using RDF (refused derived fuel) at a Chinese cement plant

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The feasibility study was conducted on a project in China for energy saving and greenhouse gas emission reduction by introducing the energy-saving and alternative energy technologies in cement plants. The cement plant selected for the feasibility study is Shanghai Plant of Shanghai Allied Cement Co., Ltd. (SAC), for RDF receive and supply facility, chlorine bypass facility, exhaust heat power generation facility and RDF production facility. The study results indicate that the exhaust power generation can save energy of 4,700 tons/y as crude, or energy saving rate of 25.5%, and that replacing part of coal by RDF and exhaust power generation can reduce CO2 emissions by 25,500 and 18,500 tons/y, respectively. For the investment recovery, it is estimated that the investment can be recovered in 9 years, and the project value is 81.399 million Yuan with the initial investment and project profit in each year discounted to the present value. These results fail to satisfy the SAC's investment standards. (NEDO)

  2. Application of a Chilled Ammonia-based Process for CO2 Capture to Cement Plants

    NARCIS (Netherlands)

    Pérez-Calvo, José Francisco; Sutter, Daniel; Gazzani, Matteo; Mazzotti, Marco

    2017-01-01

    The chilled ammonia process (CAP) is considered one of the most promising alternatives to amine-based absorption processes for post-combustion carbon capture applied to power plants. This work provides an insight on the CAP adaptations required to meet the conditions found in the flue gas emitted in

  3. Thermal properties of fly ash substituted slag cement waste forms for disposal of Savannah River Plant salt waste

    International Nuclear Information System (INIS)

    Roy, D.M.; Kaushal, S.; Licastro, P.H.; Langton, C.A.

    1985-01-01

    Waste processing at the Savannah River Plant will involve reconstitution of the salts (NaNO 3 , NaNO 2 , NaOH, etc.) into a concentrated solution (32 weight percent salts) followed by solidification in a cement-based waste form for burial. The stability and mechanical durability of such a 'saltstone monolith' will depend largely on the temperature reached due to heat of hydration and the thermal properties of the waste form. Fly ash has been used as an inexpensive constituent and to moderate the hydration and setting processes so as to avoid reaching prohibitively high temperatures which could cause thermal stresses. Both high-calcium and low-calcium fly ashes have been studied for this purpose. Other constituents of these mixes include granulated blast furnace slag and finely crushed limestone. Adiabatic temperature increase and thermal conductivity of these mixes have been studied and related x-ray diffraction and scanning electron microscopy studies carried out to understand the hydration process

  4. Report of year 2000 version on basic survey for promotion of joint execution. Modernization of Bekabad Cement Plant

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the result of applying the COP3 clean development mechanism to Bekabad Cement Plant in Uzbekistan. One of the three existing outdated wet process kilns will be converted into a new NSP kiln (having the same production capacity as now of 726,000 tons/year). Upstream and downstream facilities will be renewed, and environmental devices such as electric dust collectors and bag filters will be installed to enhance the productivity, conserve the energies, and reduce production of greenhouse effect gases and different pollutants. The total construction cost will be US$84,432,000. Reducible energy consumption and reduction in the greenhouse effect gases will be 73,232 toe/year and 176,528 toe/year respectively in a single fiscal year of 2006, and cumulative total amount in 20 years until 2025 will be 1,464,640 toe and 3,530,560 t. The energy saving effect per US$1,000 will be 17.87 toe, and the greenhouse gas reduction effect will be 43.08 t. In case of using such a soft loan as the special Yen loan for environment, the internal profit rate after tax will be 7.63%, which is not necessarily high as the business profitability. However, the profit and loss calculation sheet indicates that profit will be produced in two years after the inauguration of the operation, which is promised as relatively high possibility of realization. (NEDO)

  5. The effect of statistical analytical measurement variations on the plant control parameters and production costs in cement manufacturing – a case study

    Directory of Open Access Journals (Sweden)

    A. D. Love

    2010-01-01

    Full Text Available Raw materials used in cement manufacturing normally have varying chemical compositions and require regular analyses for plant control purposes. This is achieved by using several analytical instruments, such as XRF and ICP. The values obtained for the major elements Ca, Si, Fe and Al, are used to calculate the plant control parameters Lime Saturation Factor (LSF, Silica Ratio (SR and Alumina Modulus (AM. These plant control parameters are used to regulate the mixing and blending of various raw meal components and to operate the plant optimally. Any errors and large fluctuations in these plant parameters not only influence the quality of the cement produced, but also have a major effect on the cost of production of cement clinker through their influence on the energy consumption and residence time in the kiln. This paper looks at the role that statistical variances in the analytical measurements of the major elements Ca, Si, Fe and Al can have on the ultimate LSF, SR and AM values calculated from these measurements. The influence of too high and too low values of the LSF, SR and AM on clinker quality and energy consumption is discussed, and acceptable variances in these three parameters, based on plant experiences, are established. The effect of variances in the LSF, SR and AM parameters on the production costs is then analysed, and it is shown that variations of as large as 30% and as little as 5% can potentially occur. The LSF calculation incorporates most chemical elements and therefore is prone to the largest number of variations due to statistical variances in the analytical determinations of the chemical elements. Despite all these variations in LSF values they actually produced the smallest influence on the production cost of the clinker. It is therefore concluded that the LSF value is the most practical parameter for plant control purposes.

  6. Paul Pinna avab Estonia Talveaias omanimelise baari / Christel Karits

    Index Scriptorium Estoniae

    Karits, Christel, 1966-

    2006-01-01

    Rahvusooper Estonia sajanda sünnipäeva puhul etendub 12. ja 13. septembril Estonia Talveaias lavastus "Paul Pinnat otsimas". Tekst on 95% osas Paul Pinna ja Karl August Hindrey sulest, dramatiseeris ja lavastas Heidi Sarapuu

  7. Estonia--Going Home Again: Returning to the Roots.

    Science.gov (United States)

    Pedak-Kari, Maria

    This paper provides background on The National Library of Estonia (NLE), discusses a fellowship project for developing the National Library, and presents the impressions of the author, an Estonian American, who traveled to Estonia. The NLE looks to the West for automation, information, and institutional modeling. The NLE is Estonia's equivalent of…

  8. Estonia mulls own nuclear power plant

    Index Scriptorium Estoniae

    2008-01-01

    Andrus Ansip ja Matti Vanhanen kirjutasid alla strateegilise koostöö leppele. Võimalik ka ühise tuumaelektrijaama ehitus. Prantsuse energia- ja arenguminister Jean-Louis Borloo kohtus majandusminister Juhan Partsiga

  9. Cementation of secondary wastes generated from carbonisation of spent organic ion exchange resins from nuclear power plants

    International Nuclear Information System (INIS)

    Sathi Sasidharan, N.; Deshingkar, D.S.; Wattal, P.K.

    2004-07-01

    The spent IX resins containing radioactive fission and activation products from power reactors are highly active solid wastes generated during operations of nuclear reactors. Process for carbonization of IX resins to achieve weight and volume reduction has been optimized on 50 dm 3 /batch pilot test rig. The process generates carbonaceous residue, organic liquid condensates (predominantly styrene) and aqueous alkaline scrubber solutions as secondary wastes. The report discusses laboratory tests on leaching of 137 Cs from cement matrix incorporating carbonaceous residues and extrapolation of results to 200 liter matrix block. The cumulative fraction of 137 Cs leached from 200 liter cement matrix was estimated to be 0.0021 in 200 days and 0.0418 over a period of 30 years. Incorporation of organic liquid condensates into cement matrix has been tried out successfully. Thus two types of secondary wastes generated during carbonization of spent IX resins can be immobilized in cement matrix. (author)

  10. 76 FR 28318 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

    Science.gov (United States)

    2011-05-17

    ... Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants AGENCY... Emission Standards for Hazardous Air Pollutants from the Portland Cement Manufacturing Industry Response to... by the Portland Cement Industry and the New Source Performance Standards for Portland Cement Plants...

  11. Cement Formation

    DEFF Research Database (Denmark)

    Telschow, Samira; Jappe Frandsen, Flemming; Theisen, Kirsten

    2012-01-01

    Cement production has been subject to several technological changes, each of which requires detailed knowledge about the high multiplicity of processes, especially the high temperature process involved in the rotary kiln. This article gives an introduction to the topic of cement, including...... an overview of cement production, selected cement properties, and clinker phase relations. An extended summary of laboratory-scale investigations on clinkerization reactions, the most important reactions in cement production, is provided. Clinker formations by solid state reactions, solid−liquid and liquid......−liquid reactions are discussed, as are the influences of particles sizes on clinker phase formation. Furthermore, a mechanism for clinker phase formation in an industrial rotary kiln reactor is outlined....

  12. Ordovician timescale in Estonia: recent developments

    Directory of Open Access Journals (Sweden)

    Hints, Olle

    2006-06-01

    Full Text Available Over 150 years of progress in the Ordovician geology and stratigraphy of Estonia has resulted in one of the most precise Ordovician timescales in the world. In this paper, an up-to-date version of the Ordovician timescale of Estonia is provided. Recent developments in graptolite, chitinozoan, and conodont biostratigraphy, and the correlation with the global standard are briefly commented upon. Application of the regional subseries rank is discussed and two new names are proposed: “Vinni” for the upper subseries of the Viru Series, and “Atla” for the upper subseries of the Harju Series.

  13. Estonia: In and Out of Crisis

    Directory of Open Access Journals (Sweden)

    Viktor Trasberg

    2012-12-01

    Full Text Available The paper analyses Estonian economic developments during the first decade of 21st century. Estonia provided in that period a clear-cut example of the classical business cycle with an extreme bubble-burst sequence of economic activities. The author analyses the reasons on such a volatile economic growth pattern and explains economic cycle management particularities in Estonia. In the frames of macroeconomic developments will be analyzed monetary and fiscal policies. The author argues, that Estonia’s fiscal policy has been always pro-cyclical, what has deepened country’s macroeconomic volatility. The paper also analyses critically the government activities and policies during the recent crisis

  14. Rahvusooper Estonia interjööride renoveerimine = Renovation of the Estonia National Opera House interiors

    Index Scriptorium Estoniae

    2007-01-01

    2006. a. lõpetati Rahvusooperi Estonia publikuruumide renoveerimine. Sisearhitektid Juta Lember ja Aulo Padar. Siseviimistluse ja laemaali (E. Okas, E. Kits, R. Sagrits) restaureerimine ja konserveerimine: KAR Grupp. Akustik Linda Madalik. 8 värv. vaadet

  15. Increase in the amount of evaporator concentrate from nuclear power plants in cemented products; Aumento da quantidade de concentrado de evaporador proveniente de usinas nucleares em produtos cimentados

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Bruna S., E-mail: brusilveirac@gmail.com [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil); Tello, Clédola C.O., E-mail: tellocc@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2017-07-01

    Nuclear power plants, research centers and other nuclear facilities are sources of radioactive liquid waste generation. These wastes can come from cooling of the primary reactor system, cleaning spent pool of fuel, washing contaminated clothing, among others. One of the most used methods for the treatment of these aqueous flows is the evaporation, which generates the concentrate of the evaporator, waste classified as low and medium level of radiation. Norms determine that radioactive waste must be minimized, and that to be accepted in repositories, they must be solidified. The work sought to reduce the volume of the evaporated concentrate waste and its subsequent solidification in cement. In order to carry out the tests, the evaporator concentrate (CE) simulation solution was prepared and then dried in an oven. Subsequently, cementation of the dry material was made using cement, fluidizer, NaOH and water. After a curing time of 28 days, the compressive strength tests were made for all specimens obtained, and for the samples that obtained resistance above that required by the norm, which is 10MPa, the percentages of reject incorporated and volume reduction. The results showed that, by drying the evaporator concentrate, it was possible to reduce the volume of the waste generated by up to 27% in relation to the waste without drying, which shows that drying is an effective way to increase the incorporation of the evaporator concentrate in packaged waste.

  16. Case study of an MBT plant producing SRF for cement kiln co-combustion, coupled with a bioreactor landfill for process residues.

    Science.gov (United States)

    Grosso, Mario; Dellavedova, Stefano; Rigamonti, Lucia; Scotti, Sergio

    2016-01-01

    The paper describes the performances of the energy recovery pathway from the residual waste based on the production of a Solid Recovered Fuel (SRF) to be exploited via co-combustion in a cement kiln. The SRF is produced in a single stream Mechanical-Biological Treatment plant, where bio-drying of the waste is followed by mechanical refining in order to fulfil the quality requirements by the cement kilns. Peculiar of this MBT is the fact that sorting residues are disposed in a nearby landfill, managed according to a bioreactor approach, where landfill gas is collected for electric energy recovery. A detailed mass and energy balance of the system is presented based on one year operational data, followed by its Life Cycle Assessment. Results show that the system is energetically and environmentally effective, with most of the impacts being more than compensated by the savings of materials and energy. Major role in determining such outcome is the displacement of petcoke in the cement kiln, both in terms of its fossil CO2 emissions and of its life cycle impacts, including the trans-oceanic transport. To check the robustness of the results, two sensitivity analyses are performed on the landfill gas collection efficiency and on the avoided electric energy mix. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Concrete = aggregate, cement, water?

    International Nuclear Information System (INIS)

    Jelinek, J.

    1990-01-01

    Concrete for the Temelin nuclear power plant is produced to about 70 different formulae. For quality production, homogeneous properties of aggregates, accurate proportioning devices, technological discipline and systematic inspections and tests should be assured. The results are reported of measuring compression strength after 28 days for different concrete samples. The results of such tests allow reducing the proportion of cement, which brings about considerable savings. Reduction in cement quantities can also be achieved by adding ash to the concrete mixes. Ligoplast, a plasticizer addition is used for improving workability. (M.D). 8 figs

  18. A feasibility study of municipal solid waste incineration fly ash utilisation in Estonia.

    Science.gov (United States)

    Berber, Hakan; Frey, Ruedi; Voronova, Viktoria; Koroljova, Arina

    2017-09-01

    The purpose of this paper is to discuss the alternative environmental management options for the utilisation of municipal solid waste (MSW) incineration fly ash (FA), which is generated at Iru Power Plant where MSW is incinerated in Estonia. To determine sustainable and economically feasible environmental management options for MSW incineration FA in Estonia, CO 2 sequestration with a further carbonation process was examined. A partial Cost & Benefit Analysis has been conducted to compare the carbonation process to the current situation. Two carbonation options were developed. Option 1 is to use carbonated FA in any other processes based on the waste-to-product principle. Option 2 is to send carbonated FA to the non-hazardous landfill in Tallinn, Estonia. Important parameters, such as Net Present Value (NPV), Internal Rate of Return (IRR), Benefit-Cost Ratio (BCR) and Break Even Point (BEP), have been calculated for carbonation options and the current case. In addition, a sensitivity analysis has been conducted to examine its robustness. The results showed that the best option is carbonation Option 1 with NPV of 9,209,662 EUR, IRR of 43%, BCR of 2.63 and BEP between 2018 and 2019. Both Options 1 and 2 constitute more sustainable and environmentally friendly management options compared to the current situation. It can be concluded that this preliminary feasibility study showed that running a carbonation plant may be profitable and sustainable for Estonia. Currently, there is no treatment technology for MSW incineration FA in Estonia and FA is sent to a neighbouring country for further utilisation. This is the first study to demonstrate FA management options with economic and environmental benefits.

  19. SMEs in Estonia : Achievements and Worries

    Index Scriptorium Estoniae

    1999-01-01

    Phare toetusel ja Eesti Väikeettevõtete Assotsiatsiooni abil läbi viidud uurimusest "The State of Small Business in Estonia" (väikeettevõtted Eestis). Tabelid ja diagrammid. Eesti väikeettevõtete probleemid, osalemine eksport/import tegevuses, peamised probleemid pangalaenude taotlemisel

  20. Rural renewable energy (prospects) in Estonia

    Energy Technology Data Exchange (ETDEWEB)

    Tomson, T. [Estonian Energy Research Institute, Tallinn (Estonia); Kaeaermann, L. [Estonian National Maritime Board, Tallinn (Estonia); Raesaar, P. [Tallinn Technological University, Tallinn (Estonia)

    1997-12-31

    Total potential share of renewables (biomass, wind, hydropower and solar) in Estonia is 35 %. Total real share (wood, wood chips) of renewables is only about 4.5 % (1995). The constrains and prospects of the development are discussed. The attention is focused on rural conditions

  1. Estonia purjetab filmiturule / Jüri Laulik

    Index Scriptorium Estoniae

    Laulik, Jüri, 1959-

    2003-01-01

    Saksamaal Berliinis esilinastub pidulikult 13. oktoobril poliitiline põnevusfilm "Balti torm" ("Baltic Storm"), mis kujutab parvlaev "Estonia" hukku. Režissöör ja üks stsenariste on Reuben Leder, peaosades Greta Scacchi ja Jürgen Prochnow. Kaasa teeb ka Donald Sutherland USA kindrali rollis. Eesti näitlejaist teeb kaasa Rein Oja

  2. Friends of Estonia discuss next move

    Index Scriptorium Estoniae

    2011-01-01

    1. juulil 2011 avas Eesti president Toomas Hendrik Ilves Riigikogu konverentsikeskuses Eesti sõprade kokkutuleku raames korraldatava sümpoosioni “Quo vadis, Estonia?”, kus ütles, et Eesti järgmine eesmärk on riiklike ja ühiskondlike struktuuride tugevdamisele keskendumine

  3. Rural renewable energy (prospects) in Estonia

    Energy Technology Data Exchange (ETDEWEB)

    Tomson, T [Estonian Energy Research Institute, Tallinn (Estonia); Kaeaermann, L [Estonian National Maritime Board, Tallinn (Estonia); Raesaar, P [Tallinn Technological University, Tallinn (Estonia)

    1998-12-31

    Total potential share of renewables (biomass, wind, hydropower and solar) in Estonia is 35 %. Total real share (wood, wood chips) of renewables is only about 4.5 % (1995). The constrains and prospects of the development are discussed. The attention is focused on rural conditions

  4. The cement recycling of the earthquake disaster debris by Hachinohe Cement Co., Ltd

    International Nuclear Information System (INIS)

    Kataoka, Masayuki

    2015-01-01

    A tremendous quantity of earthquake disaster debris and tsunami sediment was resulted by the Great East Japan Earthquake on March 11, 2011. Hachinohe Cement Co., Ltd., a Sumitomo Osaka Cement subsidiary, was the first cement industry company to receive and process such waste materials outside of their usual prefecture area, while the company is performing their treatment and recycling services locally in Hachinohe City and Aomori Prefecture. This report provides an explanation about the recycling mechanism of waste materials and by-products in cement manufacturing process, and introduces an example of actual achievements for the disaster debris treatment by utilizing the cement recycling technologies at the Hachinohe Cement Plant. (author)

  5. Energy Efficiency Improvement and Cost Saving Opportunities for Cement Making An ENERGY STAR® Guide for Energy and Plant Managers

    NARCIS (Netherlands)

    Worrell, E.; Kermeli, Katerina; Galitsky, Christina

    The cost of energy as part of the total production costs in the cement industry is significant, typically at 20 to 40% of operational costs, warranting attention for energy efficiency to improve the bottom line. Historically, energy intensity has declined, although more recently energy intensity

  6. "Gerontiuse unenägu" Estonias / Igor Garšnek

    Index Scriptorium Estoniae

    Garšnek, Igor, 1958-

    2010-01-01

    2. aprillil Estonia kontserdisaalis toimunud Edward Elgari oratooriumi "Gerontiuse unenägu" ettekandest, esitasid: ERSO, Estonia ooperikoor, Estonia poistekoor, kammerkoor Voces Musicales, Helen Lokuta, Bernhard Gärtner, Priit Volmer, dirigent Carlos Spiereri

  7. Environmental levels of PCDD/Fs and metals around a cement plant in Catalonia, Spain, before and after alternative fuel implementation. Assessment of human health risks

    Energy Technology Data Exchange (ETDEWEB)

    Rovira, Joaquim [Laboratory of Toxicology and Environmental Health, School of Medicine, Universitat Rovira i Virgili, Sant Llorenç 21, 43201 Reus, Catalonia (Spain); Environmental Engineering Laboratory, Departament d' Enginyeria Quimica, Universitat Rovira i Virgili, Av. Països Catalans 26, 43007 Tarragona, Catalonia (Spain); Nadal, Martí, E-mail: marti.nadal@urv.cat [Laboratory of Toxicology and Environmental Health, School of Medicine, Universitat Rovira i Virgili, Sant Llorenç 21, 43201 Reus, Catalonia (Spain); Schuhmacher, Marta [Laboratory of Toxicology and Environmental Health, School of Medicine, Universitat Rovira i Virgili, Sant Llorenç 21, 43201 Reus, Catalonia (Spain); Environmental Engineering Laboratory, Departament d' Enginyeria Quimica, Universitat Rovira i Virgili, Av. Països Catalans 26, 43007 Tarragona, Catalonia (Spain); Domingo, José L. [Laboratory of Toxicology and Environmental Health, School of Medicine, Universitat Rovira i Virgili, Sant Llorenç 21, 43201 Reus, Catalonia (Spain)

    2014-07-01

    The concentrations of As, Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, Sb, Sn, Tl, V, and Zn, and the levels of polychlorinated dibenzo-p-dioxins and dibenzofurans were determined in samples of soil, vegetation, and air, collected in the vicinity of a cement plant (Catalonia, Spain), before (January 2011 and July 2011) and after (January 2012 and June 2013) alternative fuel partial substitution (fossil fuels by sewage sludge). Seven sampling points were selected at different directions and distances to the facility including two background sampling points. The results were used to assess the health risk assessment for the population living near the facility. Only few significant differences were found before and after alternative fuel partial substitution (Mn in soils and Cd in vegetation). Non-carcinogenic risks were below the safety threshold (HQ < 1), while carcinogenic risks were below 10{sup −5}, or exceeding slightly that value, always in the range considered as assumable (10{sup −6}–10{sup −4}). - Highlights: • The environmental impact of a cement plant using alternative fuel was monitored. • No significant differences in most pollutants were noted after the fuel change. • Traffic has a notable influence on the environmental levels of PCDD/Fs and metals. • Human health risks were below safety thresholds regardless of the used fuel.

  8. Metals and dioxins on the air in a cement plant; Niveles ambientales de metales y dioxinas en las proximidades de una planta cementera

    Energy Technology Data Exchange (ETDEWEB)

    Domingo, J. L.

    2001-07-01

    In May 2000, the levels of a number of metals (As, Cd, Pb, Hg, Zn, Co, Cu, Mn, Sn, Tl, Cr, Ni, and V) were determined in soil and herbage samples taken from 16 sites in the vicinity of a cement plant (Sta. Margarita i els Monjos, Barcelona). During 2000, metal concentrations were also analyzed quarterly in filters from three stations placed near the facility. In soil and herbage samples, Mn and Zn showed the highest levels. However, most metal concentrations were similar or even lower than previously reported values for other areas in Catalonia. On the other hand, the levels of polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) were also determined in 4 soil and 16 herbage samples. In comparison with the concentrations found in other places, the present levels are rather low. The current results show that the cement plant has a low impact on the metal and PCDD/PCDF levels in the environment under influence of the facility. (Author) 19 refs.

  9. Application of spherical fly-ash particles to study spatial deposition of atmospheric pollutants in northen-eastern Estonia

    International Nuclear Information System (INIS)

    Alliksaar, T.

    2000-01-01

    Spherical fly-ash particles, emitted to the atmosphere in the high-temperature combustion process of fossil fuels, were found in considerable amounts in analysed snow samples of north-eastern Estonia. Spatial deposition of particles in snow cover is compared with the results of surface sediment samples of lakes. The results from snow characterise well the distribution of pollution sources and the distance from the main power plants in north eastern Estonia. Variations in particle deposition of closely situated snow samples were found to be negligible. Fly-ash particle influxes in snow samples correlate well with modelled maximum concentration fields of flyash in the near-surface air layer. (author)

  10. 76 FR 2832 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

    Science.gov (United States)

    2011-01-18

    ... Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants AGENCY...) from the Portland Cement Manufacturing Industry and Standards of Performance (NSPS) for Portland Cement... Standards for Hazardous Air Pollutant From the Portland Cement Manufacturing Industry Docket, Docket ID No...

  11. Childhood deaths from external causes in Estonia, 2001–2005

    Directory of Open Access Journals (Sweden)

    Soonets Ruth

    2007-07-01

    Full Text Available Abstract Background In 2000, the overall rate of injury deaths in children aged 0–14 was 28.7 per 100000 in Estonia, which is more than 5 times higher than the corresponding rate in neighbouring Finland. This paper describes childhood injury mortality in Estonia by cause and age groups, and validates registration of these deaths in the Statistical Office of Estonia against the autopsy data. Methods The data on causes of all child deaths in Estonia in 2001–2005 were abstracted from the autopsy protocols at the Estonian Bureau of Forensic Medicine. Average annual mortality rates per 100,000 were calculated. Coverage (proportion of the reported injury deaths from the total number of injury deaths and accuracy (proportion of correctly classified injury deaths of the registration of causes of death in Statistical Office of Estonia were assessed by comparing the Statistical Office of Estonia data with the data from Estonian Bureau of Forensic Medicine. Results Average annual mortality from external causes in 0–14 years-old children in Estonia was 19.1 per 100,000. Asphyxia and transport accidents were the major killers followed by poisoning and suicides. Relative contribution of these causes varied greatly between age groups. Intent of death was unknown for more than 10% of injury deaths. Coverage and accuracy of registration of injury deaths by Statistical Office of Estonia were 91.5% and 95.3%, respectively. Conclusion Childhood mortality from injuries in Estonia is among the highest in the EU. The number of injury deaths in Statistical Office of Estonia is slightly underestimated mostly due to misclassification for deaths from diseases. Accuracy of the Statistical Office of Estonia data was high with some underestimation of intentional deaths. Moreover, high proportion of death with unknown intent suggests underestimation of intentional deaths. Reduction of injury deaths should be given a high priority in Estonia. More information on

  12. Childhood deaths from external causes in Estonia, 2001-2005.

    Science.gov (United States)

    Väli, Marika; Lang, Katrin; Soonets, Ruth; Talumäe, Marika; Grjibovski, Andrej M

    2007-07-17

    In 2000, the overall rate of injury deaths in children aged 0-14 was 28.7 per 100000 in Estonia, which is more than 5 times higher than the corresponding rate in neighbouring Finland. This paper describes childhood injury mortality in Estonia by cause and age groups, and validates registration of these deaths in the Statistical Office of Estonia against the autopsy data. The data on causes of all child deaths in Estonia in 2001-2005 were abstracted from the autopsy protocols at the Estonian Bureau of Forensic Medicine. Average annual mortality rates per 100,000 were calculated. Coverage (proportion of the reported injury deaths from the total number of injury deaths) and accuracy (proportion of correctly classified injury deaths) of the registration of causes of death in Statistical Office of Estonia were assessed by comparing the Statistical Office of Estonia data with the data from Estonian Bureau of Forensic Medicine. Average annual mortality from external causes in 0-14 years-old children in Estonia was 19.1 per 100,000. Asphyxia and transport accidents were the major killers followed by poisoning and suicides. Relative contribution of these causes varied greatly between age groups. Intent of death was unknown for more than 10% of injury deaths. Coverage and accuracy of registration of injury deaths by Statistical Office of Estonia were 91.5% and 95.3%, respectively. Childhood mortality from injuries in Estonia is among the highest in the EU. The number of injury deaths in Statistical Office of Estonia is slightly underestimated mostly due to misclassification for deaths from diseases. Accuracy of the Statistical Office of Estonia data was high with some underestimation of intentional deaths. Moreover, high proportion of death with unknown intent suggests underestimation of intentional deaths. Reduction of injury deaths should be given a high priority in Estonia. More information on circumstances around death is needed to enable establishing the intent of death.

  13. Childhood deaths from external causes in Estonia, 2001–2005

    Science.gov (United States)

    Väli, Marika; Lang, Katrin; Soonets, Ruth; Talumäe, Marika; Grjibovski, Andrej M

    2007-01-01

    Background In 2000, the overall rate of injury deaths in children aged 0–14 was 28.7 per 100000 in Estonia, which is more than 5 times higher than the corresponding rate in neighbouring Finland. This paper describes childhood injury mortality in Estonia by cause and age groups, and validates registration of these deaths in the Statistical Office of Estonia against the autopsy data. Methods The data on causes of all child deaths in Estonia in 2001–2005 were abstracted from the autopsy protocols at the Estonian Bureau of Forensic Medicine. Average annual mortality rates per 100,000 were calculated. Coverage (proportion of the reported injury deaths from the total number of injury deaths) and accuracy (proportion of correctly classified injury deaths) of the registration of causes of death in Statistical Office of Estonia were assessed by comparing the Statistical Office of Estonia data with the data from Estonian Bureau of Forensic Medicine. Results Average annual mortality from external causes in 0–14 years-old children in Estonia was 19.1 per 100,000. Asphyxia and transport accidents were the major killers followed by poisoning and suicides. Relative contribution of these causes varied greatly between age groups. Intent of death was unknown for more than 10% of injury deaths. Coverage and accuracy of registration of injury deaths by Statistical Office of Estonia were 91.5% and 95.3%, respectively. Conclusion Childhood mortality from injuries in Estonia is among the highest in the EU. The number of injury deaths in Statistical Office of Estonia is slightly underestimated mostly due to misclassification for deaths from diseases. Accuracy of the Statistical Office of Estonia data was high with some underestimation of intentional deaths. Moreover, high proportion of death with unknown intent suggests underestimation of intentional deaths. Reduction of injury deaths should be given a high priority in Estonia. More information on circumstances around death is

  14. New data about the climate of Estonia

    International Nuclear Information System (INIS)

    Jaagus, Jaak

    1999-01-01

    During last 100-150 years global climate has changed significantly. Climate warming has also observed in Estonia. The aim of this paper is to analyse how different are old climate normals calculated for 1881-1880 from present-day normals (1966-1998). The new normals are calculated for monthly and annual mean air temperature at 22 stations in Estonia. Mean monthly and annual precipitation totals and snow cover duration are found at 69 stations and observation sites. Significant differences were determined between the old and new averages. As a rule, air temperature has increased while 0.4 deg C in case of annual values. Snow cover duration has decreased during this century. Its new normals are lower by 5-10 days, what is a direct consequence of climate warming

  15. Kunstiakadeemia kolib ajutiselt Estonia puiesteele / Mari Kodres

    Index Scriptorium Estoniae

    Kodres, Mari

    2009-01-01

    Eesti Kunstiakadeemia on 2010. a. alguseks vanadest ruumidest kolinud hoonesse aadressil Estonia pst. 7. Rüütelkonna hoones leidis endale ajutise kodu vabade kunstide teaduskonna enamik erialasid. Veebruari algul toimuvast tühjendamispeost. EKA uue maja arhitektuurikonkursi võitis Taani arhitektuuribüroodes Sea ja Effekt valminud töö "Art Plaza". Uue hoone ehitus algab aprillis, valmimistähtajaks on 2012. a. kevad

  16. Thunderstorms caused by southern cyclones in Estonia

    OpenAIRE

    Kaupo Mändla; Sven-Erik Enno; Mait Sepp

    2014-01-01

    The relationships between the frequency and duration of thunderstorms, lightning and southern cyclones over Estonia are presented for the period 1950–2010. A total of 545 southern cyclones and 2106 thunderstorm days were detected, whereas 11.3% of the observed thunder days were associated with southern cyclones. At the same time, 29.2% of all southern cyclones were accompanied by thunderstorms. In the thunder season, however, this percentage was much higher, reaching up to 80% in summer month...

  17. Valmis film parvlaev Estonia katastroofist / Imre Kaas

    Index Scriptorium Estoniae

    Kaas, Imre

    2003-01-01

    Saksamaal on valminud poliitiline põnevusfilm "Balti torm" ("Baltic Storm"), mis kujutab parvlaev "Estonia" hukku venelaste vandenõu tulemusena. Film jõuab Eestis linale novembri alul. Produtsent ja esialgse stsenaariumi autor koosHenning Wittega on Jutta Rabe, režissöör ja üks stsenariste Reuben Leder. Kaasa teeb ka Donald Sutherland USA kindrali rollis. Eesti näitlejaist teeb kaasa Rein Oja

  18. Studies on the incorporation of spent ion exchange resins from nuclear power plants into bitumen and cement

    International Nuclear Information System (INIS)

    Bonnevie-Svendsen, M.; Tallberg, K.; Aittola, P.; Tollbaeck, H.

    1976-01-01

    The joint Nordic incorporation experiments should provide technical data needed for the assessment of solidification techniques for wastes from nuclear reactors in the Nordic countries. Spent ion exchange resins are a main fraction of such wastes, and more knowledge about their incorporation is wanted. The effects of simulated and real ion exchange wastes on the quality of bitumen and cement incorporation products were studied. Blown and distilled bitumen and three Portland cement qualities were used. Product characterizations were based on properties relevant for safe waste management, storage, transport and disposal. The applicability and relevance of established and suggested tests is discussed. Up to 40-60% dry resin could be incorporated into bitumen without impairing product qualities. Products with higher resin contents were found to swell in contact with water. The products had a high leach resistance. Their form stability was improved by incorporated resins. Product qualities appeared to be less affected by physico-chemical variables than by mechanical process parameters. Pure resin-cement products tend to decompose in water. Product qualities were strongly affected by a variety of physico-chemical process parameters, and integer products were only obtained within narrow tolerance limits. Caesium was rapidly leached out. To attain integer products and improved leach resistance within technically acceptable tolerance limits it was necessary to utilize stabilizing and caesium-retaining additives such as Silix and vermiculite. Under the present conditions the water content of the resins limited the amounts that could be incorporated in 40-50wt% or about 70vol.% water-saturated (containing 20-40% dry) resin. (author)

  19. A new step in cement plant bypass technology; Une nouvelle avancee pour les by-pass en cimenterie

    Energy Technology Data Exchange (ETDEWEB)

    Civiel, G. [Technip, 92 - Rueil-Malmaison (France)

    2001-12-01

    The demand of valorizing more and more waste fuel in cement industry results in an increase of volatile element quantities in kiln system, particularly chlorine. In 'Ciment, Betons, Platres, Chaux' no 849 May-June 2001, we made reference to the two new approaches developed by TECHNIP CL to solve the problem of the volatile elements in clinker burning lines: the raw meal curtain and the Taiheyo by-pass. The following article is focused on the second system. (author)

  20. 77 FR 46371 - National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing...

    Science.gov (United States)

    2012-08-03

    ...-AQ93 National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing... Portland Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants,'' which was... Manufacturing Industry and Standards of Performance for Portland Cement Plants'' under Docket ID No. EPA-HQ-OAR...

  1. Youth negotiation and performance of masculine identities in rural Estonia

    NARCIS (Netherlands)

    Trell, Elen; van Hoven, Bettina; Huigen, Paulus

    2014-01-01

    This paper explores key shared places and practices through which young men in rural Estonia perform and construct masculine identities. Whereas powerful images of rural places and rural masculinity exist and are reproduced in public discourse in Estonia, not much is known about how masculinities

  2. Ekspert välistab Estonia lepingust taganemise / Aivar Pau

    Index Scriptorium Estoniae

    Pau, Aivar

    2006-01-01

    Tartu Ülikooli rahvusvahelise õiguse õppetooli hoidja Lauri Mälksoo peab mõeldamatuks Eesti ühepoolset otsust loobuda riikidevahelisest hauarahulepingust ja tõsta Estonia vrakk merepõhjast üles. Riigikogu erikomisjoni esimees Margus Leivo on algatanud Estonia vraki ülestõstmiseks internetis allkirjade kogumise kampaania

  3. CEMENT SLURRIES FOR GEOTHERMAL WELLS CEMENTING

    Directory of Open Access Journals (Sweden)

    Nediljka Gaurina-Međimurec

    1994-12-01

    Full Text Available During a well cementing special place belongs to the cement slurry design. To ensure the best quality of cementing, a thorough understanding of well parameters is essential, as well as behaviour of cement slurry (especially at high temperatures and application of proven cementing techniques. Many cement jobs fail because of bad job planning. Well cementing without regarding what should be accomplished, can lead to well problems (channels in the cement, unwanted water, gas or fluid production, pipe corrosion and expensive well repairs. Cementing temperature conditions are important because bot-tomhole circulating temperatures affect slurry thickening time, arheology, set time and compressive strength development. Knowing the actual temperature which cement encounters during placement allows the selection of proper cementing materials for a specific application. Slurry design is affected by well depth, bottom hole circulating temperature and static temperature, type or drilling fluid, slurry density, pumping time, quality of mix water, fluid loss control, flow regime, settling and free water, quality of cement, dry or liquid additives, strength development, and quality of the lab cement testing and equipment. Most Portland cements and Class J cement have shown suitable performances in geot-hermal wells. Cement system designs for geothermal wells differ from those for conventional high temperature oil and gas wells in the exclusive use of silica flour instead of silica sand, and the avoidance of fly ash as an extender. In this paper, Portland cement behaviour at high temperatures is described. Cement slurry and set cement properties are also described. Published in literature, the composition of cement slurries which were tested in geothermal conditions and which obtained required compressive strength and water permeability are listed. As a case of our practice geothermal wells Velika Ciglena-1 and Velika Ciglena-la are described.

  4. Physical, chemical and mineralogical characterization of water treatment plant waste for use in soil-cement brick; Caracterizacao fisica, quimica e mineralogica de residuo de estacao de tratamento de aguas para aproveitamento em tijolo solo-cimento

    Energy Technology Data Exchange (ETDEWEB)

    Pessin, L.R.; Destefani, A.Z.; Holanda, J.N.F., E-mail: larapessin@hotmail.com [Universidade Estadual do Norte Fluminense Darcy Ribeiro (CCT/PPGECM/UENF), Campos dos Goytacazes, RJ (Brazil)

    2011-07-01

    The water treatment plants (WTP) for human consumption generate huge amounts of waste in the form of sludge (sludge) that have been over the years mostly inadequately prepared in water resources and the environment. Moreover, traditional methods of disposal of waste water treatment plants commonly used are generally costly activities. An alternative method for disposal of this waste abundant is its incorporation in ceramic products. This work is focused on the physical-chemical and mineralogical composition of a sample of waste water treatment plants from the region of Campos dos Goytacazes-RJ to their use in the manufacture of soil-cement brick. Several characterization techniques were used including X-ray diffraction, X-ray fluorescence, scanning electron microscopy, picnometry, particle size analysis and plasticity. The experimental results indicate that the waste water treatment plants have the potential to be used in the manufacture of ecologic soil-cement bricks. (author)

  5. Lunar cement

    Science.gov (United States)

    Agosto, William N.

    1992-01-01

    With the exception of water, the major oxide constituents of terrestrial cements are present at all nine lunar sites from which samples have been returned. However, with the exception of relatively rare cristobalite, the lunar oxides are not present as individual phases but are combined in silicates and in mixed oxides. Lime (CaO) is most abundant on the Moon in the plagioclase (CaAl2Si2O8) of highland anorthosites. It may be possible to enrich the lime content of anorthite to levels like those of Portland cement by pyrolyzing it with lunar-derived phosphate. The phosphate consumed in such a reaction can be regenerated by reacting the phosphorus product with lunar augite pyroxenes at elevated temperatures. Other possible sources of lunar phosphate and other oxides are discussed.

  6. 137Cs in forest ecosystems in Estonia

    International Nuclear Information System (INIS)

    Martin, Jueri; Martin, Ljudmilla; Paern, Henn; Vilde, Raimolt

    1996-01-01

    Full text: In the recently published 'Europe's Environment' (1995) one can find the map on 1 37C s cumulative deposition in Europe after the Chernobyl accident (source: De Corte et al., 1990). On this map most of the Eastern Europe including Baltic Sea region is practically uncovered. In this reason we decided to present data on accumulation of 1 37C s in the forest ecosystems in Estonia. Field sampling for current study has been conducted in 1986 - 1994. 1 37C s concentrations were measured in different compartments of model trees, ground vegetation layers, debris and topsoil. The amount of 1 37C s varied from 1.9 kBq/m 2 in continental Estonia to 28.8 kBq/m 2 in north-eastern Ne part of Estonia. The results obtained correspond to data presented in Wahlstroem et al., (1992) for Finland. According to the 'Europe's Environment' criteria northeastern Estonia belongs to the third cumulative deposition zone (10 to 32 kBq/m 2 ). In Estonia the total deposition of 1 37C s varies in the range from practically zero to 3.9 kBq/m 2 . The calculations of Realo et al. (1994) back to May 1, 1986 gave figures from 0 to 21 kBq/m 2 . In macro lichens Cetraria, Cladina, Cladonia the rapid changes in 1 37C s concentrations were observed: 0.06 - 0.18 kBq/kg in 1982-85, 0.93 - 6.23 kBq/kg in 1986-87, 0.27 -4.26 kBq/kg in 1988-89, 0.05 - 1.46 kBq/kg in 1990-91 and, finally, 0.03 - 0.46 kBq/kg in 1993-94. At the end of the observation period average value of the 1 37C s concentrations was the same as maximum before the CRA and decline of the concentrations was 4 times during six years. Average concentrations of 1 3 7 C s in two common forest mosses Pleurozium shreberi and Hylocomium splendens was 0.43 kBq/kg of dry matter and in forest debris 0.38 kBq/kg. In 1986 the highest concentration in mushrooms - 16.6 kBq/kg was found in Lactarius sp. (Martin, L., et al., 1991). In 1991 samples of 41 different mushroom species from 63 sample sites mostly in Scots pine stands were analyzed. The

  7. Long-term deposition patterns of airborne wastes in the North-East of Estonia

    International Nuclear Information System (INIS)

    Kaasik, M.; Kaasik, H.

    1999-01-01

    The deposition loads of fly ash and sulfur have been high in the North-East Estonia since the late fifties, when the oil shale energetics, chemical and cement industry achieved the remarkable extent. The combined effects of both pollutants have seriously damaged sensitive ecosystems (forest on podsolic soils and bog). Most of sulphur deposition is closely related to the oil shale fly ash deposition. The main effects are related with alkalisation due to accumulation of fly ash components and the Sphagnum growth inhibition due to sulfur load. These effects have the time scale of several years or even more. The pollution loads have been changed during recent 40 years due to launching and reconstruction of enterprises (incl. purification systems) and variations of production capacity. First representative data on air pollution deposition originate from the middle of eighties. Only model estimations could be used to quantify the deposition fluxes before that time, as well as for assessing the future scenarios

  8. TECHNOLOGICAL CHANGES IN THE CEMENT MANUFACTURING INDUSTRY.

    Science.gov (United States)

    WESSON, CARL E.

    THE PURPOSE OF THIS STUDY IS TO PRESENT A PRELIMINARY PICTURE OF OCCUPATIONAL CHANGES BROUGHT ABOUT IN THE MANUFACTURE OF CEMENT AS A RESULT OF INTRODUCING AUTOMATED EQUIPMENT. ONE AUTOMATED AND SEVERAL CONVENTIONAL TYPE CEMENT PLANTS WERE STUDIED. ANALYSIS OF DATA OBTAINED THROUGH RESEARCH AND DATA COLLECTED DURING THE STUDY REVEALED THAT…

  9. Corrosivity of cement pastes with addition of sludge generated in water treatment plant; Estudo da corrosividade de pastas de cimento com adicao de lodo gerado em estacao de tratamento de agua

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, R.A.; Martins, B.E.D.B.S.; Couto, V.M.P.; Carvalho, L.J.; Almeida, V.C., E-mail: valeria@eq.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Centro de Tecnologia. Escola de Quimica

    2011-07-01

    The amount of sludge produced in a water treatment plant (WTP) is an important economic factor in the context of waste treatment. The present article has the objective of study the corrosion of cement pastes produced with blended sludge. Aqueous extracts were produced from the milling of masses containing 5%, 10% and 30% of sludge in relation to cement after 28 days of healing. These extracts were used for polarization assays in order to determine the corrosiveness of the folders when in contact with the used fittings. Moreover, other chemical analysis tests were carried out for sludge characterization: X-ray fluorescence and X-ray diffraction. The obtained results point to the possibility of use of the studied cement masses in the development of construction materials promoting the economic reuse of WTP sludge before discarded in landfills. (author)

  10. FY 2000 report on the basic survey to promote Joint Implementation, etc. Energy conservation by modernization of a cement plant (Double Horse Cement Co.) in China; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Chugoku cement kojo (Double Horse Cement) kindaika ni yoru sho energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigational study was conducted of possibilities of energy conservation and greenhouse effect gas emission reduction in the cement production process of Double Horse Cement Co., Mianyang City, Sichuan Province, China. Double Horse Cement adopts the wet type long kiln production system and has a production ability of approximately 1.5 million t/y. In the project, as to three production lines out of the six production lines, improvement was planned to be made of the technologies on the following: mixing of raw materials, grinding of raw materials, NSP, clinker cooler, clinker pre-grinder, high-efficiency separator, waste heat use power generation, etc. As a result of the study, it was found that the energy conservation amount obtained was 54,646 toe/y. And, the amount of greenhouse effect gas reduction was 169,086 t-CO2/y. The total fund required for this project was approximately 5.553 billion yen and the internal earning rate was 7.36% after tax. When the project is carried out, expenses vs. effects are 9.8 toe/million yen in energy conservation amount and 30.4 t-CO2/million yen in greenhouse effect gas reduction. (NEDO)

  11. Re-use of drinking water treatment plant (DWTP) sludge: Characterization and technological behaviour of cement mortars with atomized sludge additions

    International Nuclear Information System (INIS)

    Husillos Rodriguez, N.; Martinez Ramirez, S.; Blanco Varela, M.T.; Guillem, M.; Puig, J.; Larrotcha, E.; Flores, J.

    2010-01-01

    This paper aims to characterize spray-dried DWTP sludge and evaluate its possible use as an addition for the cement industry. It describes the physical, chemical and micro-structural characterization of the sludge as well as the effect of its addition to Portland cements on the hydration, water demand, setting and mechanical strength of standardized mortars. Spray drying DWTP sludge generates a readily handled powdery material whose particle size is similar to those of Portland cement. The atomized sludge contains 12-14% organic matter (mainly fatty acids), while its main mineral constituents are muscovite, quartz, calcite, dolomite and seraphinite (or clinoclor). Its amorphous material content is 35%. The mortars were made with type CEM I Portland cement mixed with 10 to 30% atomized sludge exhibited lower mechanical strength than the control cement and a decline in slump. Setting was also altered in the blended cements with respect to the control.

  12. Pilot projects for the remediation of Sillamaee uranium tailings in Estonia

    International Nuclear Information System (INIS)

    Kaasik, T.; Siinmaa, A.

    2001-01-01

    First Estonian uranium, produced in a pilot plant at Narva, was presented to Soviet military administration in 1945 and just a year later - 1946 - installation of an uranium production plant was started at Sillamaee, Estonia. Estonian local ore - alum shale - containing only 0,026% of uranium was used for uranium production for nearly five years, after the plant was launched in 1948. The uranium mine, having been activated from 1947 to 1952, was left in status of 'active conservation' for 17 years, until finally closed in 1969. Potential threats of this hidden legacy have never been revealed. After close-down of local uranium mine, more than 4 million tons of ore, imported mostly from Central and East European countries: Czechoslovakia, Hungary and Eastern Germany were processed at Sillamaee. These activities have left a large tailings impoundment with the total volume of ca. 8 million cubic meters in the immediate vicinity of the Baltic Sea. Today the plant is privatized, converted to civil purposes and provides together its power generating facilities ca. 1200 jobs in the socially sensitive area of North-East Estonia, while environmental hazards of the history, however, remain: - Continuous seepage of tailing waters into the sea contributes and would contribute over long term to the pollution of the Baltic Sea; - stability of the tailings dam seaside under present conditions can not be guaranteed thus risking a sudden release of partly liquid tailings due to potential dam failure; - uncovered surface of the tailings presents a health hazard due to dusting and radon release and hinders the revitalization of the area. The conceptual design of the Estonia's largest environmental remediation project, done by Wismut, is now complete and first implementation steps are underway. The project for mine area restoration is in initiation phase; it shall reveal the current and potential environmental hazards of the facility and create the concept for necessary rehabilitation

  13. FY 2000 Fundamental study for promotion of jointed implementations. Feasibility study on energy saving effect and reducing CO2 emissions by use of RDF in cement plants in China; 2000 nendo Chugoku cement kojo ni okeru RDF katsuyo ni yoru shoene koka oyobi nisanka tanso haishutsu sakugen ni kansuru feasibility study chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The feasibility study was conducted on a project in China for energy saving and greenhouse gas emission reduction by introducing the energy-saving and alternative energy technologies in cement plants. The cement plant selected for the feasibility study is Shanghai Plant of Shanghai Allied Cement Co., Ltd. (SAC), for RDF receive and supply facility, chlorine bypass facility, exhaust heat power generation facility and RDF production facility. The study results indicate that the exhaust power generation can save energy of 4,700 tons/y as crude, or energy saving rate of 25.5%, and that replacing part of coal by RDF and exhaust power generation can reduce CO2 emissions by 25,500 and 18,500 tons/y, respectively. For the investment recovery, it is estimated that the investment can be recovered in 9 years, and the project value is 81.399 million Yuan with the initial investment and project profit in each year discounted to the present value. These results fail to satisfy the SAC's investment standards. (NEDO)

  14. The measurement of 129I for the cement and the paraffin solidified low and intermediate level wastes (LILWs), spent resin or evaporated bottom from the pressurized water reactor (PWR) nuclear power plants.

    Science.gov (United States)

    Park, S D; Kim, J S; Han, S H; Ha, Y K; Song, K S; Jee, K Y

    2009-09-01

    In this paper a relatively simple and low cost analysis procedure to apply to a routine analysis of (129)I in low and intermediate level radioactive wastes (LILWs), cement and paraffin solidified evaporated bottom and spent resin, which are produced from nuclear power plants (NPPs), pressurized water reactors (PWR), is presented. The (129)I is separated from other nuclides in LILWs using an anion exchange adsorption and solvent extraction by controlling the oxidation and reduction state and is then precipitated as silver iodide for counting the beta activity with a low background gas proportional counter (GPC). The counting efficiency of GPC was varied from 4% to 8% and it was reversely proportional to the weight of AgI by a self absorption of the beta activity. Compared to a higher pH, the chemical recovery of iodide as AgI was lowered at pH 4. It was found that the chemical recovery of iodide for the cement powder showed a lower trend by increasing the cement powder weight, but it was not affected for the paraffin sample. In this experiment, the overall chemical recovery yield of the cement and paraffin solidified LILW samples and the average weight of them were 67+/-3% and 5.43+/-0.53 g, 70+/-7% and 10.40+/-1.60 g, respectively. And the minimum detectable activity (MDA) of (129)I for the cement and paraffin solidified LILW samples was calculated as 0.070 and 0.036 Bq/g, respectively. Among the analyzed cement solidified LILW samples, (129)I activity concentration of four samples was slightly higher than the MDA and their ranges were 0.076-0.114 Bq/g. Also of the analyzed paraffin solidified LILW samples, five samples contained a little higher (129)I activity concentration than the MDA and their ranges were 0.036-0.107 Bq/g.

  15. The measurement of 129I for the cement and the paraffin solidified low and intermediate level wastes (LILWs), spent resin or evaporated bottom from the pressurized water reactor (PWR) nuclear power plants

    International Nuclear Information System (INIS)

    Park, S.D.; Kim, J.S.; Han, S.H.; Ha, Y.K.; Song, K.S.; Jee, K.Y.

    2009-01-01

    In this paper a relatively simple and low cost analysis procedure to apply to a routine analysis of 129 I in low and intermediate level radioactive wastes (LILWs), cement and paraffin solidified evaporated bottom and spent resin, which are produced from nuclear power plants (NPPs), pressurized water reactors (PWR), is presented. The 129 I is separated from other nuclides in LILWs using an anion exchange adsorption and solvent extraction by controlling the oxidation and reduction state and is then precipitated as silver iodide for counting the beta activity with a low background gas proportional counter (GPC). The counting efficiency of GPC was varied from 4% to 8% and it was reversely proportional to the weight of AgI by a self absorption of the beta activity. Compared to a higher pH, the chemical recovery of iodide as AgI was lowered at pH 4. It was found that the chemical recovery of iodide for the cement powder showed a lower trend by increasing the cement powder weight, but it was not affected for the paraffin sample. In this experiment, the overall chemical recovery yield of the cement and paraffin solidified LILW samples and the average weight of them were 67±3% and 5.43±0.53 g, 70±7% and 10.40±1.60 g, respectively. And the minimum detectable activity (MDA) of 129 I for the cement and paraffin solidified LILW samples was calculated as 0.070 and 0.036 Bq/g, respectively. Among the analyzed cement solidified LILW samples, 129 I activity concentration of four samples was slightly higher than the MDA and their ranges were 0.076-0.114 Bq/g. Also of the analyzed paraffin solidified LILW samples, five samples contained a little higher 129 I activity concentration than the MDA and their ranges were 0.036-0.107 Bq/g.

  16. 76 FR 2860 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

    Science.gov (United States)

    2011-01-18

    ... Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants AGENCY... Portland Cement Manufacturing Industry Docket, Docket ID No. EPA-HQ-OAR-2002-0051, 1200 Pennsylvania Ave... Portland Cement Manufacturing Industry Docket, EPA West, Room 3334, 1301 Constitution Ave., NW., Washington...

  17. Mõnitav kõverpeegel Estonia hukust / Heino Levald

    Index Scriptorium Estoniae

    Levald, Heino, 1930-

    2003-01-01

    Saksa poliitiline põnevusfilm "Balti torm" ("Baltic Storm"), mis kujutab parvlaev "Estonia" hukku : stsenarist, produtsent Jutta Rabe : režissöör Reuben Leder. Mereakadeemia professori hinnang filmi sõnumile

  18. Uudised : Rossini "Wilhelm Tell" Estonias. Cavalli ooper Amsterdamis

    Index Scriptorium Estoniae

    2008-01-01

    Gioachino Rossini ooperi "Wilhelm Tell" kontsertettekandest 18. ja 20. dets. Rahvusooper Estonias (peaosas Rauno Elp, külalisesinejaks Mario Zeffiri). Itaalia barokihelilooja Francesco Cavalli ooperi "Ercole amante" lavastamisest Madalmaade Ooperis Amsterdamis (lavastaja David Alden, esietendus 11. jaanuaril)

  19. Estonia film venitab saladuste loori / Heiki Suurkask, Andres Laasik

    Index Scriptorium Estoniae

    Suurkask, Heiki, 1972-

    2003-01-01

    Saksamaal Berliinis esilinastus poliitiline põnevusfilm "Balti torm" ("Baltic Storm"), mis kujutab parvlaev "Estonia" hukku. Esilinastuse ja filmi ümber toimuvast. Lisatud lühiintervjuu Riina Kionkaga, Eesti suursaadikuga Saksamaal

  20. Kuulus Ralf Langbacka lavastab Estonias Verdi "Othello" / Andres Laasik

    Index Scriptorium Estoniae

    Laasik, Andres, 1960-2016

    2005-01-01

    Rahvusooper Estonia 8. septembril 2005 Rocca al Mares asuvas Coral Clubi spordikeskuses esietenduvast ooperist "Othello", etendus valmib koostöös Tampere Ooperiga. 7. aprillil Tampere Talos toimuvast esietendusest

  1. Henning Witte : Estonia-film tuleb / Villem Valme

    Index Scriptorium Estoniae

    Valme, Villem, 1977-

    2000-01-01

    Kavandatavast katastrooffilmist "Baltic Storm", mis on ajendatud väidetest, et "Estonia" uppus maffiavandenõu tõttu. Stsenaristideks on Juta Rabe, Henning Witte ja Kaj Holmberg. Ka : Nädal nr. 47, lk. 5

  2. Impact of Fuel Selection on Techno-environmental Performance of Post-combustion Calcium Looping Process Applied to a Cement Plant

    NARCIS (Netherlands)

    Schakel, Wouter; Orregioni, Gabriel; Strømman, Anders; Ramirez, Andrea

    Calcium looping CO2 capture is a promising technology to reduce CO2 emissions from cement production. Coal is generally considered the fuel used to drive the calcium looping process as coal is already used as feedstock for cement production. This study assesses the impact of different fuels (coal,

  3. Environmental remediation of the former Soviet military uranium milling site at Sillamae, Estonia: Features of approach

    International Nuclear Information System (INIS)

    Kassik, T.; Siinmaa, A.

    1999-01-01

    Quick launch of the nuclear program was a high priority for the Soviet military, as a uranium production plant installation was started at Sillamae, Estonia, in 1946. Estonian local ore - alum shale - containing only 0.03% of uranium was used for uranium production for nearly five years, after the plant was launched in 1948. Altogether more than 4 million tons of ore, imported mostly from Central and East European countries (Czechoslovakia, Hungary and Eastern Germany) were processed at Sillamae. These activities have left a large tailings impoundment with the total volume of ca 8 million cubic meters in the immediate vicinity of the Baltic Sea. Today the plant is privatized, converted to civil purposes and provides ca. 1200 jobs in the socially sensitive area of North-East Estonia, while environmental hazards from the past; however, remain: Continuous seepage of tailing waters into the sea contributes and would contribute over long term to the pollution of the Baltic Sea; stability of the tailings dam seaside under present conditions can not be guaranteed thus risking a sudden release of partly liquid tailings due to potential dam failure; and uncovered surface of the tailings presents a health hazard due to dusting and radon release and hinders the revitalization of the area. The conceptual design of the Estonia's largest environmental project is now complete, the completion of practical remedial works by the end of 2005 will render Sillamae project a pioneer among Central and East European restoration projects of this character. This paper presents characteristic features of Sillamae remediation project, planning the use of best technical solutions, especially considering the vulnerability of geotechnical stability. (author)

  4. Ceramic residue for producing cements, method for the production thereof, and cements containing same

    OpenAIRE

    Sánchez de Rojas, María Isabel; Frías, Moisés; Asensio, Eloy; Medina Martínez, César

    2014-01-01

    [EN] The invention relates to a ceramic residue produced from construction and demolition residues, as a puzzolanic component of cements. The invention also relates to a method for producing said ceramic residues and to another method of producing cements using said residues. This type of residue is collected in recycling plants, where it is managed. This invention facilitates a potential commercial launch.

  5. Polymer-cement interactions towards improved wellbore cement fracture sealants

    Science.gov (United States)

    Beckingham, B. S.; Iloejesi, C.; Minkler, M. J.; Schindler, A. K.; Beckingham, L. E.

    2017-12-01

    Carbon capture, utilization, and storage (CCUS) in deep geologic formations is a promising means of reducing point source emissions of CO2. In these systems, CO2 is captured at the source and then injected to be utilized (eg. in enhanced oil recovery or as a working fluid in enhanced geothermal energy plants) or stored in geologic formations such as depleted oil and gas reservoirs or saline aquifers. While CCUS in subsurface systems could aid in reducing atmospheric CO2 emissions, the potential for CO2 leakage from these systems to overlying formations remains a major limitation and poses a significant risk to the security of injected CO2. Thus, improved materials for both initial wellbore isolation and repairing leakage pathways that develop over time are sought. One approach for the repair of cement fractures in wellbore (and other) systems is the injection of polymer materials into the fracture with a subsequent environmentally dependent (temperature, pressure, pH, etc.) densification or solidification. Here, we aim to investigate novel polymer materials for use to repair leaking wellbores in the context of CCUS. We synthesize and fully characterize a series of novel polymer materials and utilize a suite of analysis techniques to examine polymer-cement interactions at a range of conditions (namely temperature, pressure and pH). Initial findings will be leveraged to design novel polymer materials for further evaluation in polymer-cement composite cores, cement fracture healing, and the aging behavior of healed cements.

  6. District heating rehabilitation project. Viljandi - Estonia. Final report

    International Nuclear Information System (INIS)

    1998-04-01

    The main objective of the project has been to assist Viljandi Municipality with the rehabilitation of their district heating system, and thereby to support the positive development of the district heating system in Viljandi to a more energy efficient and rational system and to achieve a significantly decrease in the pollution from the production of heat energy in Viljandi. The project has also included technical assistance to Viljandi DH company, in order to make them capable of operation and maintaining of the new substations, and also training of the local operational staff for operation of the complete district heating system. Viljandi is a county and is centrally located in Estonia, which makes Viljandi very suitable as recipient for a demonstration project. One important objective was the projects significantly positive environmental impact in reduction of the generated emissions of CO 2 , NO x and SO 2 , as the project includes installation of more efficient energy systems and supply of heat from the 2 existing district heating plants (both are partly fired with wood chips) instead of heating by very old and worn-out coal fired boilers and inexpedient designed substations with the present operational conditions. (EG)

  7. District heating rehabilitation project. Viljandi - Estonia. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-04-01

    The main objective of the project has been to assist Viljandi Municipality with the rehabilitation of their district heating system, and thereby to support the positive development of the district heating system in Viljandi to a more energy efficient and rational system and to achieve a significantly decrease in the pollution from the production of heat energy in Viljandi. The project has also included technical assistance to Viljandi DH company, in order to make them capable of operation and maintaining of the new substations, and also training of the local operational staff for operation of the complete district heating system. Viljandi is a county and is centrally located in Estonia, which makes Viljandi very suitable as recipient for a demonstration project. One important objective was the projects significantly positive environmental impact in reduction of the generated emissions of CO{sub 2}, NO{sub x} and SO{sub 2}, as the project includes installation of more efficient energy systems and supply of heat from the 2 existing district heating plants (both are partly fired with wood chips) instead of heating by very old and worn-out coal fired boilers and inexpedient designed substations with the present operational conditions. (EG)

  8. Assessment of operators’ mental workload using physiological and subjective measures in cement, city traffic and power plant controlcenters

    Directory of Open Access Journals (Sweden)

    Majid Fallahi

    2016-06-01

    Conclusion: The results suggested that when operators’ mental demands especially in traffic control and power plant tasks increased, their mental fatigue and stress level increased and their mental health deteriorated. Therefore, it may be necessary to implement an ergonomic program or administrative control to manage mental probably health in these control centers.Furthermore, by evaluating MW, the control center director can organize the human resources for each MW condition to sustain the appropriate performance as well as improve system functions.

  9. Remediation and decommissioning of radioactive waste facilities in Estonia

    International Nuclear Information System (INIS)

    Putnik, H.; Realo, E.

    2001-01-01

    Full text: The nuclear training facility at Paldiski was constructed in the early 1960's by the former USSR Navy. The hull sections of Delta and Echo class submarines each housing a full-sized ship reactor were installed in the main building of the site for training of navy personnel in safe operation of the submarine nuclear reactor systems. The first reactor was commissioned in 1968 and the second in 1982, while both was shut down in 1989. After Estonia's reproclamation of independence in 1991 the responsibility for the clean up and decommissioning of the Paldiski site became a subject of negotiations between Russia and Estonia. As the result Estonia took the ownership and control of the site in September 1995. Before the take over the Russian authorities defuelled the reactors and transported the spent fuel to Russia, dismantled the hull sections not related with reactor systems, seal-welded the hull sections housing the reactor vessels with their primary circuitry and enclosed those in reinforced concrete sarcophagi. The auxiliary facilities and radioactive waste were left intact. Main goals of the Conceptual Decommissioning Plan for the Paldiski facilities, developed under the auspices of the Paldiski International Expert Reference Group (Pier, a group established at the request of the Estonian government to advise local authorities to maintain the decommissioning and waste management at Paldiski) were defined as following: Establishing the waste management system and a long term monitored interim storage, corresponding to internationally accepted safety standards and capable to condition, receive and store all the waste generated during decommissioning of the facility; Reductions of the extent of radiologically controlled areas as much as possible, in order to minimise maintenance requirements. To achieve these goals the following main tasks were addressed in the short and medium term site management action plans: Rearrangement of site for the needs of

  10. Producing cement

    Energy Technology Data Exchange (ETDEWEB)

    Stone, E G

    1923-09-12

    A process and apparatus are described for producing Portland cement in which pulverized shale is successively heated in a series of inclined rotary retorts having internal stirrers and oil gas outlets, which are connected to condensers. The partially treated shale is removed from the lowermost retort by a conveyor, then fed separately or conjointly into pipes and thence into a number of vertically disposed retorts. Each of these retorts may be fitted interiorly with vertical arranged conveyors which elevate the shale and discharge it over a lip, from whence it falls to the bottom of the retorts. The lower end of each casing is furnished with an adjustable discharge door through which the spent shale is fed to a hopper, thence into separate trucks. The oil gases generated in the retorts are exhausted through pipes to condensers. The spent shale is conveyed to a bin and mixed while hot with ground limestone. The admixed materials are then ground and fed to a rotary kiln which is fired by the incondensible gases derived from the oil gases obtained in the previous retorting of the shale. The calcined materials are then delivered from the rotary kiln to rotary coolers. The waste gases from the kiln are utilized for heating the retorts in which the ground shale is heated for the purpose of extracting therefrom the contained hydrocarbon oils and gases.

  11. CO2 Capture for Cement Technology

    DEFF Research Database (Denmark)

    Pathi, Sharat Kumar

    , whereas in a normal cement plant, it is 0.9 kg/ kg cl. However the thermal energy demand in the integrated plant increases from 3.9 MJ/ kg cl to 5.6 MJ/ kg cl. But on the other side this additional energy spent can be recovered as a high quality heat to generate electricity. The potential to generate...... electricity depends on the scale of the plant, the bigger the production capacity of cement plant the better, with capacity higher than 3400 tons of clinker/day is required to produce captive electricity to meet the demand both from the cement plant operations and from the CO2 capture system operations....

  12. The importance of chemical analysis and quality-assurance for environmental mediation and acceptance in the use of secondary fuels in the cement plant Leube as an essential part of the ecological business strategy

    International Nuclear Information System (INIS)

    Mlekusch, T.

    2000-11-01

    In this paper I tried to combine the fields of environmental technology, environmental analysis, quality-management, environmental mediation and limiting values an the example of the use of secondary-fuels in the cement plant Leube in Gartenau (Austria). This project has proved to be very satisfying for the company and the adjoining owners. The first chapter deals with relations between environment and technology. A chronological description of the use of secondary fuels shows the development in this technology. The reactions of trace-elements in the burning process of cement clinker are described in the second chapter. Limiting values and the protection of human beings by the use of them are explained in the third chapter. The environmental mediation project of the use of secondary fuels in Gartenau is object of the fourth chapter. An essential part to acceptance is contributed by a good working quality-management and laboratory. (author)

  13. Operating experience with KRAFTWERK UNION cementation line

    International Nuclear Information System (INIS)

    Podmaka, L.; Tomik, L.

    1988-01-01

    A facility is described designed for fixation in a cement matrix of the radioactive concentrate produced by thickening waste water from the Bohunice nuclear power plant. The cementation line output is 0.6 m 3 concentrate/h. The concentrate is put in 200 l drums. The individual operating units, cement management, air conditioning, dosimetric monitoring and the building part are described. The requirements for the operators and the assessment of the quality of raw materials and the product are discussed. (M.D.). 3 figs., 4 refs

  14. Talks on nuclear plant break down

    Index Scriptorium Estoniae

    2007-01-01

    Kasvavad probleemid Leedu tuumaelektrijaama projektiga. Läbirääkimistest Leedu valitsuse ja NDX Energija vahel. DnB Nord Bankas nimetas projekti liiga riskantseks ja kulukaks. Lisa: Eesti Energia board member suggests plant for Estonia

  15. An approach to assess the Particulate Matter exposure for the population living around a cement plant: modelling indoor air and particle deposition in the respiratory tract

    Energy Technology Data Exchange (ETDEWEB)

    Sánchez-Soberón, Francisco; Mari, Montse; Kumar, Vikas [Environmental Engineering Laboratory, Departament d' Enginyeria Quimica, Universitat Rovira i Virgili, Av. Països Catalans 26, 43007 Tarragona, Catalonia (Spain); Rovira, Joaquim [Environmental Engineering Laboratory, Departament d' Enginyeria Quimica, Universitat Rovira i Virgili, Av. Països Catalans 26, 43007 Tarragona, Catalonia (Spain); Laboratory of Toxicology and Environmental Health, School of Medicine, IISPV, Universitat Rovira i Virgili, Sant Llorenç 21, 43201 Reus, Catalonia (Spain); Nadal, Martí [Laboratory of Toxicology and Environmental Health, School of Medicine, IISPV, Universitat Rovira i Virgili, Sant Llorenç 21, 43201 Reus, Catalonia (Spain); Schuhmacher, Marta, E-mail: marta.schuhmacher@urv.cat [Environmental Engineering Laboratory, Departament d' Enginyeria Quimica, Universitat Rovira i Virgili, Av. Països Catalans 26, 43007 Tarragona, Catalonia (Spain); Laboratory of Toxicology and Environmental Health, School of Medicine, IISPV, Universitat Rovira i Virgili, Sant Llorenç 21, 43201 Reus, Catalonia (Spain)

    2015-11-15

    In this paper we studied the exposure to three size fractions of outdoor particulate matter (PM{sub 10}, PM{sub 2.5}, and PM{sub 1}) collected in an area influenced by a cement plant. For that purpose, three groups of population were evaluated (children, adults and retired) in two seasons (summer and winter). Outdoor measured PM concentrations, as well as physiological parameters and activity patterns of the three groups of population were used as input data in two different models. The first one was an indoor air quality model, used to elucidate indoor PM concentrations in different microenvironments. The second one was a dosimetry model, used to evaluate the internal exposure and the distribution of the different PM fractions in the respiratory tract. Results from the indoor air quality model showed that special attention must be paid to the finest particles, since they penetrate indoors in a greater degree. Highest pulmonary doses for the three PM sizes were reported for retired people, being this a result of the high amount of time in outdoor environments exercising lightly. For children, the exposure was mainly influenced by the time they also spend outdoors, but in this case due to heavy intensity activities. It was noticed that deposition of fine particles was more significant in the pulmonary regions of children and retired people in comparison with adults, which has implications in the expected adverse health effects for those vulnerable groups of population. - Highlights: • PM deposition in the respiratory tract was evaluated for three population groups. • Activity patterns and different microenvironments were used in our calculation. • Outdoor activities are the main contributors to PM deposited mass. • Children experienced the highest deposition dose in the pulmonary region. • Retired registered the highest deposited mass in the respiratory tract as a whole.

  16. KHD combustion chamber. Flexible use of alternative fuels in the cement plant; KHD Brennkammer. Flexibler Einsatz von alternativen Brennstoffen im Zementwerk

    Energy Technology Data Exchange (ETDEWEB)

    Schuermann, Heiko [Humboldt Wedag GmbH, Koeln (Germany)

    2012-07-01

    In many parts of the world, the use of alternative fuels is a recognized measure for reducing the CO{sub 2} emissions that result from burning primary fuels such as coal, oil and natural gas. Alternative or secondary fuels are the terms used for combustible residues from industrial and commercial manufacturing processes, agricultural production, and sorted municipal refuse. Due to the wide range of possible sources of alternative fuels, there is very great variation in their energy content, ash, moisture content, particle size, form, density etc., so there is no patent solution for their use in a cement plant. For proper operation of the rotary kiln, it is particularly important to use alternative fuel qualities that have good heat value and reactivity in order to achieve a stable, hot sintering zone and to completely burnout the highest possible amount of the fuel while it is suspended in the air stream. Combustion in the calciner places fewer demands on the properties of the alternative fuels than combustion in the rotary kiln burner does. This means that the calciner is the ideal combustion point for the usage of alternative fuels. To enable maximum possible flexibility for the combustion of widely differing alternative fuels in the calciner, KHD Humboldt Wedag offers the option of installing a combustion chamber in the modular PYROCLON calciner system. Due to the operating characteristics of this combustion chamber, which are described in the following sections of this article, even alternative fuels with low heat values and a low degree of preparation can be safely and completely burnt. (orig.)

  17. An approach to assess the Particulate Matter exposure for the population living around a cement plant: modelling indoor air and particle deposition in the respiratory tract

    International Nuclear Information System (INIS)

    Sánchez-Soberón, Francisco; Mari, Montse; Kumar, Vikas; Rovira, Joaquim; Nadal, Martí; Schuhmacher, Marta

    2015-01-01

    In this paper we studied the exposure to three size fractions of outdoor particulate matter (PM 10 , PM 2.5 , and PM 1 ) collected in an area influenced by a cement plant. For that purpose, three groups of population were evaluated (children, adults and retired) in two seasons (summer and winter). Outdoor measured PM concentrations, as well as physiological parameters and activity patterns of the three groups of population were used as input data in two different models. The first one was an indoor air quality model, used to elucidate indoor PM concentrations in different microenvironments. The second one was a dosimetry model, used to evaluate the internal exposure and the distribution of the different PM fractions in the respiratory tract. Results from the indoor air quality model showed that special attention must be paid to the finest particles, since they penetrate indoors in a greater degree. Highest pulmonary doses for the three PM sizes were reported for retired people, being this a result of the high amount of time in outdoor environments exercising lightly. For children, the exposure was mainly influenced by the time they also spend outdoors, but in this case due to heavy intensity activities. It was noticed that deposition of fine particles was more significant in the pulmonary regions of children and retired people in comparison with adults, which has implications in the expected adverse health effects for those vulnerable groups of population. - Highlights: • PM deposition in the respiratory tract was evaluated for three population groups. • Activity patterns and different microenvironments were used in our calculation. • Outdoor activities are the main contributors to PM deposited mass. • Children experienced the highest deposition dose in the pulmonary region. • Retired registered the highest deposited mass in the respiratory tract as a whole.

  18. Thunderstorms caused by southern cyclones in Estonia

    Directory of Open Access Journals (Sweden)

    Kaupo Mändla

    2014-05-01

    Full Text Available The relationships between the frequency and duration of thunderstorms, lightning and southern cyclones over Estonia are presented for the period 1950–2010. A total of 545 southern cyclones and 2106 thunderstorm days were detected, whereas 11.3% of the observed thunder days were associated with southern cyclones. At the same time, 29.2% of all southern cyclones were accompanied by thunderstorms. In the thunder season, however, this percentage was much higher, reaching up to 80% in summer months. The number of thunder days was largest when the centres of southern cyclones passed a measuring station at a distance less than 500 km. The number of cloud-to-ground lightning strikes related to southern cyclones was larger than that of any other thunder events. The results of our study demonstrate that the intensity of thunderstorms related to southern cyclones is higher than that of other thunderstorms. Correlation analysis revealed statistically significant relationships between the frequency of thunder days related to southern cyclones and the frequency of southern cyclones, also between the frequency of thunder days related to southern cyclones and days of other thunder events.

  19. University courses on radiation protection in Estonia

    International Nuclear Information System (INIS)

    Realo, Enn

    1999-01-01

    A brief overview is given on the educational courses containing topics in the field of radiation protection in the Tallinn Technical University and in the University of Tartu, Estonia. It follows from the analysis that at present there is no complete system for education or training of experts in the field. At the same time a significant deficit in specialists and experts is one of the major barriers in the development of an efficient radiation protection infrastructure in this country. A comparison of the course topics to the syllabus for the training of qualified experts recommended by EC and by IAEA demonstrates the items, which need a further development and an expanded coverage in the existing or in future courses. These items involve, e.g., operational radiation protection and its organisation, waste management, transport, quality assurance, etc. Upgrading of courses for the missing theoretical items is not difficult, but it is not sufficient. The largest void lies in the weakness / absence of an adequate basis for practical work or exercises for students. The examples of co-operation and help provided for the existing courses, especially by the Nordic countries, are encouraging. (au)

  20. Asphalt cement poisoning

    Science.gov (United States)

    ... petroleum material that hardens when it cools. Asphalt cement poisoning occurs when someone swallows asphalt. If hot ... found in: Road paving materials Roofing materials Tile cements Asphalt may also be used for other purposes.

  1. Radioactivity of bone cement

    International Nuclear Information System (INIS)

    Scherer, M.A.; Winkler, R.; Ascherl, R.; Lenz, E.

    1993-01-01

    A total of 14 samples of different types of bone cement from five different manufacturers were examined for their radioactivity. Each of the investigated bone cements showed a low radioactivity level, i.e. between [de

  2. Ultrafine portland cement performance

    Directory of Open Access Journals (Sweden)

    C. Argiz

    2018-04-01

    Full Text Available By mixing several binder materials and additions with different degrees of fineness, the packing density of the final product may be improved. In this work, ultrafine cement and silica fume mixes were studied to optimize the properties of cement-based materials. This research was performed in mortars made of two types of cement (ultrafine Portland cement and common Portland cement and two types of silica fume with different particle-size distributions. Two Portland cement replacement ratios of 4% and 10% of silica fume were selected and added by means of a mechanical blending method. The results revealed that the effect of the finer silica fume mixed with the coarse cement enhances the mechanical properties and pore structure refinement at a later age. This improvement is somewhat lower in the case of ultrafine cement with silica fume.

  3. Sulfur polymer cement concrete

    International Nuclear Information System (INIS)

    Weber, H.H.; McBee, W.C.

    1990-01-01

    Sulfur-based composite materials formulated using sulfur polymer cement (SPC) and mineral aggregates are described and compared with conventional portland cement based materials. Materials characteristics presented include mechanical strength, chemical resistance, impact resistance, moisture permeation, and linear shrinkage during placement and curing. Examples of preparation and placement of sulfur polymer cement concrete (SC) are described using commercial scale equipment. SC applications presented are focused into hostile chemical environments where severe portland cement concrete (PCC) failure has occurred

  4. Tax wedge in Croatia, Belgium, Estonia, Germany and Slovakia

    Directory of Open Access Journals (Sweden)

    Ana Gabrilo

    2016-06-01

    Full Text Available The aim of this paper is to analyse the taxation of labour income in Croatia, Belgium,Estonia, Germany and Slovakia. Having presented an outline of tax system rules, the paper shows the decomposition of the net average tax wedge for different family types and different income levels based on the OECD methodology. The results show that all observed countries apply a progressive tax schedule, apart from Germany where taxation for higher gross wages is not progressive due to a  cap on the SIC base. When it comes to a taxpayer earning an average gross wage, a Croatian single worker without children has the lowest tax burden, followed by Estonia, Slovakia, Germany and Belgium. However, as regards taxpayers earning 400% of AGW, Estonia has the smallest tax wedge, followed by Slovakia, Germany, Croatia and Belgium. Similar results are obtained by analyzing the tax wedge for couples with two children where one spouse is out of work.

  5. Should Estonia have a nuclear power station?(Part 1)

    International Nuclear Information System (INIS)

    Frey, T.

    1992-01-01

    In developing countries the problem of energy supply can be of paramount importance. Estonia, however, being the small country of a small nation, has to take into account special considerations before deciding on the possible introduction of nuclear electricity. Should another disaster like that of Chernobyl take place on Estonian territory, the whole nation might perish. Therefore, those scientists who place national interests above all have been active looking for alternative sources of energy. The present paper discusses the situation in Northern Europe and draws the readers' attention to the still unsolved problem of nuclear waste disposal. The paper emphasises the fact that the Fifth Estonian Conference on Ecology regarded nuclear energy as entirely unacceptable for Estonia and declared its full support for the decision taken by the Estonian Government not to consider the application of nuclear power in Estonia before the year 2000. (author). 8 figs

  6. Properties of backfilling material for solidifying miscellaneous waste using recycled cement from waste concrete

    International Nuclear Information System (INIS)

    Matsuda, Atsuo; Yamamoto, Kazuo; Konishi, Masao; Iwamoto, Yoshiaki; Yoshikane, Toru; Koie, Toshio; Nakashima, Yoshio.

    1997-01-01

    A large reduction of total radioactive waste is expected, if recycled cement from the waste concrete of decommissioned nuclear power plants would be able to be used the material for backfilling mortar among the miscellaneous waste. In this paper, we discuss the hydration, strength and consistency of recycled cement compared with normal portland cement. The strength of recycled cement mortar is lower than that of normal portland cement mortar on the same water to cement ratio. It is possible to obtain the required strength to reduce the water to cement ratio by using of high range water-reducing AE agent. According to reducing of water to cement ratio, the P-type funnel time of mortar increase with the increase of its viscosity. However, in new method of self-compactability for backfilling mortar, it became evident that there was no difference between the recycled cement and normal portland cement on the self-compactability. (author)

  7. Master plan study - District heating Sillamaee municipality. Estonia. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The main deficiencies of the district heating system in Sillamae (Estonia) were identified as being inefficiency of the heat and power production plant, which has a very low capacity, lack of means for consumers to control their energy consumption due to the existing constant flow system, pollution from heat and power production based on oil shale, water and heat losses from the network and unclear agreements between the Silmet factory and Sillamae municipality. The available capital for funding is limited. It was investigated where in the system investments would have the greatest effect. A scenario where heat is supplied from individual gas-fired boilers was calculated. A financially viable scenario would be to change from cogeneration of heat and power (CHP) based on oil shale to either individual natural gas supply or peat-fueled heat production. The Sillamae municipality and the Estonian government should agree on a solution for Sillamae. There will be a cash flow problem if the project is implemented. This can be partly solved by introducing a longer loan period. it is expected that there will be no substantial changes in the consumers` heat demand in the `do nothing`scenario, and in other scenarios ca. 520 Tj/p.a. from the Solmet factory, 530 Tj/p.a. from the town and 260 Tj/p.a. as heat losses, totaling 1310 Tj/p.a.. In another scenario - the introduction of natural gas - the town`s heat demand will be 530 Tj/p.a. and there will be no heat losses. More detailed studies of environmental impacts should be undertaken. (ARW)

  8. Master plan study - District heating Sillamaee municipality. Estonia. Final report

    International Nuclear Information System (INIS)

    1997-03-01

    The main deficiencies of the district heating system in Sillamae (Estonia) were identified as being inefficiency of the heat and power production plant, which has a very low capacity, lack of means for consumers to control their energy consumption due to the existing constant flow system, pollution from heat and power production based on oil shale, water and heat losses from the network and unclear agreements between the Silmet factory and Sillamae municipality. The available capital for funding is limited. It was investigated where in the system investments would have the greatest effect. A scenario where heat is supplied from individual gas-fired boilers was calculated. A financially viable scenario would be to change from cogeneration of heat and power (CHP) based on oil shale to either individual natural gas supply or peat-fueled heat production. The Sillamae municipality and the Estonian government should agree on a solution for Sillamae. There will be a cash flow problem if the project is implemented. This can be partly solved by introducing a longer loan period. it is expected that there will be no substantial changes in the consumers' heat demand in the 'do nothing'scenario, and in other scenarios ca. 520 Tj/p.a. from the Solmet factory, 530 Tj/p.a. from the town and 260 Tj/p.a. as heat losses, totaling 1310 Tj/p.a.. In another scenario - the introduction of natural gas - the town's heat demand will be 530 Tj/p.a. and there will be no heat losses. More detailed studies of environmental impacts should be undertaken

  9. Towards unification of terrestrial gravity data sets in Estonia

    Directory of Open Access Journals (Sweden)

    Ellmann, Artu

    2009-12-01

    Full Text Available Gravity data in Estonia have been collected by different institutions over many decades. This study assesses the suitability of available gravity data for ensuring a 1 cm geoid modelling accuracy over Estonia and in the Baltic Sea region in general. The main focus of this study is on the determination and elimination of discrepancies between three nationwide datasets. It was detected that one tested historic gravity dataset contained inadmissible systematic biases with respect to other tested datasets. Possible ways of gravity data improvement are discussed. More specifically, new field observation campaigns and aspects of using their outcomes in subsequent regional geoid modelling are suggested.

  10. Radio synovectomy: First results in Estonia

    International Nuclear Information System (INIS)

    Nazarenko, S.; Samarina, G.; Poksi, A.

    2005-01-01

    Full text: In Estonia first radiosynovectomy (RSE) was carried out in 2001 at Tallinn Central Hospital, which has remained the only institution in North Estonia performing these procedures. Purpose of this study was to analyze the results and the clinical experience gained during the period of September 2001 January 2005. We performed RSE in 10 knee joints of 7 patients. Our patient population consisted of 3 males and 4 females (mean age 34, range 16-48). There were 6 patients with rheumatoid arthritis (RA) and chronic synovitis and 1 patient with haemophilia (HE) who had one episode of haemarthrosis eight month prior to RSE. In RA the duration of the disease was ranging from 2 month to 20 years. All RA patients were resistant to anti-inflammatory drugs, immunosuppressants and intraarticular steroid therapy. Prior to RSE, conventional rheumatologic evaluation and MRI scan were carried out, revealing the thickness of synovia of 2-5 mm, and minimal or no cartilage damage. In our HE patient chronic hypertrophic synovitis associated with haemarthrosis did not respond to haematological treatment: replacement of the missing clotting factor, intermittent steroids, immobilization, physical therapy. According to MRI, the thickness of synovia was patchy, 5-26 mm, the cartilage damage was absent. For RSE, intraarticular injection of radiocolloid was carried out in aseptic conditions and under local anesthesia. Treated joints were immobilized for 2 days. In 5 out of 6 RA patients the injection was performed once, in one RA patient four times. In order to minimize local inflammation and lymphatic clearance glucocorticoids were administered together with radioisotope agents. In three patients (2 with RA and 1 with HE) 27 mCi of 166-Ho-FHMA was injected, and in remaining four patients with RA - 4-6 mCi of 90-Y radiocolloid was used. All joints with Ho-FHMA were checked for radiocolloid leakage by subsequent gamma camera imaging. Treatment response was evaluated from 2 to 6 month

  11. Family doctors' involvement with families in Estonia

    Directory of Open Access Journals (Sweden)

    Lember Margus

    2004-10-01

    Full Text Available Abstract Background Family doctors should care for individuals in the context of their family. Family has a powerful influence on health and illness and family interventions have been shown to improve health outcomes for a variety of health problems. The aim of the study was to investigate the Estonian family doctors' (FD attitudes to the patients' family-related issues in their work: to explore the degree of FDs involvement in family matters, their preparedness for management of family-related issues and their self-assessment of the ability to manage different family-related problems. Methods A random sample (n = 236 of all FDs in Estonia was investigated using a postal questionnaire. Altogether 151 FDs responded to the questionnaire (response rate 64%, while five of them were excluded as they did not actually work as FDs. Results Of the respondents, 90% thought that in managing the health problems of patients FDs should communicate and cooperate with family members. Although most of the family doctors agreed that modifying of the health damaging risk factors (smoking, alcohol and drug abuse of their patients and families is their task, one third of them felt that dealing with these problems is ineffective, or perceived themselves as poorly prepared or having too little time for such activities. Of the respondents, 58% (n = 83 were of the opinion that they could modify also relationship problems. Conclusions Estonian family doctors are favourably disposed to involvement in family-related problems, however, they need some additional training, especially in the field of relationship management.

  12. Expert views from Poland and Estonia

    Directory of Open Access Journals (Sweden)

    Kaja Põlluste

    2016-12-01

    Full Text Available Background . Home care (HC is placed between the health and social welfare systems, and the clients of HC mostly need health services. Along with other providers, family doctors (FDs are usually involved in the provision of care. Objectives. This paper aims to describe and compare the involvement of HC providers to elderly and disabled persons in Poland and Estonia. Material and methods . This study is part of the international project EURHOMA P (Mapping Professional Home Care in Europe. Data was collected in 2008–2010. Experts from different areas of health and social care were queried by using a questionnaire containing structured case narratives, which were hypothetical descriptions of the situations of elderly or disabled persons living at home and in need of care. Results. There are a number of HC services, e.g. nursing, medical and social, available in both countries. The application for HC is mostly made by the patient or a close family member; the point of entry to HC can differ and depends on the client’s primary problem. FDs, together with social workers, play an important role in the provision of HC services in both countries. However, due to a shortage of round-the-clock professional services at a client’s home, families are also expected to play a large role in providing HC . Conclusions . Health care professionals, mainly those working in primary health care, play a remarkable role in access to and provision of HC services. Nevertheless, responsibility for 24-hour care lies, to a large extent, with the client’s immediate family. This situation seems to be typical in Eastern European countries.

  13. Environmental Assessment of Different Cement Manufacturing ...

    Science.gov (United States)

    Due to its high environmental impact and energy intensive production, the cement industry needs to adopt more energy efficient technologies to reduce its demand for fossil fuels and impact on the environment. Bearing in mind that cement is the most widely used material for housing and modern infrastructure, the aim of this paper is to analyse the Emergy and Ecological Footprint of different cement manufacturing processes for a particular cement plant. There are several mitigation measures that can be incorporated in the cement manufacturing process to reduce the demand for fossil fuels and consequently reduce the CO2 emissions. The mitigation measures considered in this paper were the use of alternative fuels and a more energy efficient kiln process. In order to estimate the sustainability effect of the aforementioned measures, Emergy and Ecological Footprint were calculated for four different scenarios. The results show that Emergy, due to the high input mass of raw material needed for clinker production, stays at about the same level. However, for the Ecological Footprint, the results show that by combining the use of alternative fuels together with a more energy efficient kiln process, the environmental impact of the cement manufacturing process can be lowered. The research paper presents an analysis of the sustainability of cement production , a major contributor to carbon emissions, with respect to using alternative fuels and a more efficient kiln. It show

  14. Estonia taastusravikeskuse termid : Sääse 7, Pärnu = Baths at SPA Estonia : Sääse 7, Pärnu / Margit Mutso

    Index Scriptorium Estoniae

    Mutso, Margit, 1966-

    2009-01-01

    Estonia taastusravikeskuse basseini- ja vesiravikompleksist, mille arhitektid ning sisearhitektid on Edda Soolep ja Jüri Soolep (Archimedium OÜ). Žürii hinnang kultuurkapitali aastapreemiale esitatud hoonele

  15. ULTRA-LIGHTWEIGHT CEMENT

    International Nuclear Information System (INIS)

    Fred Sabins

    2001-01-01

    The objective of this project is to develop an improved ultra-lightweight cement using ultralight hollow glass spheres (ULHS). Work reported herein addresses Task 1: Assess Ultra-Lightweight Cementing Problems and Task 3: Test Ultra-Lightweight Cements. Results reported this quarter include a review and summary of Halliburton Energy Services (HES) and BJ Services historical performance data for lightweight cement applications. These data are analyzed and compared to ULHS cement and foamed cement performances. Similar data is expected from Schlumberger, and an analysis of this data will be completed in the following phases of the project. Quality control testing of materials used to formulate ULHS cements in the laboratory was completed to establish baseline material performance standards. A testing protocol was developed employing standard procedures as well as procedures tailored to evaluate ULHS and foamed cement. This protocol is presented and discussed. Results of further testing of ULHS cements are presented along with an analysis to establish cement performance design criteria to be used during the remainder of the project. Finally, a list of relevant literature on lightweight cement performance is compiled for review during the next quarter

  16. ULTRA-LIGHTWEIGHT CEMENT

    International Nuclear Information System (INIS)

    Fred Sabins

    2001-01-01

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). Work reported herein addresses Task 1: Assess Ultra-Lightweight Cementing Issues, Task 2: Review Russian Ultra-Lightweight Cement Literature, Task 3: Test Ultra-Lightweight Cements, and Task 8: Develop Field ULHS Cement Blending and Mixing Techniques. Results reported this quarter include: preliminary findings from a literature review focusing on problems associated with ultra-lightweight cements; summary of pertinent information from Russian ultra-lightweight cement literature review; laboratory tests comparing ULHS slurries to foamed slurries and sodium silicate slurries for two different applications; and initial laboratory studies with ULHS in preparation for a field job

  17. Personal exposure to inhalable cement dust among construction workers

    International Nuclear Information System (INIS)

    Peters, Susan; Kromhout, Hans; Thomassen, Yngvar; Fechter-Rink, Edeltraud

    2009-01-01

    A case study was carried out in 2006-2007 to assess the actual cement dust exposure among construction workers involved in a full-scale construction project and as a comparison among workers involved in various stages of cement and concrete production. Full-shift personal exposure measurements were performed for several job types. Inhalable dust and cement dust (based on analysis of elemental calcium) concentrations were determined. Inhalable dust exposures at the construction site ranged from 0.05 to 34 mg/m3, with a mean concentration of 1.0 mg/m3. For inhalable cement dust mean exposure was 0.3 mg/m3 (range 0.02-17 mg/m3). Reinforcement and pouring workers had the lowest average concentrations. Inhalable dust levels in the ready-mix and pre-cast concrete plants were, on average, below 0.5 mg/m3 for inhalable dust and below 0.2 mg/m3 for inhalable cement dust. Highest dust concentrations were measured in cement production, particularly during cleaning tasks (inhalable dust GM=55 mg/m3; inhalable cement dust GM=33 mg/m3) at which point the workers wore personal protective equipment. Elemental measurements showed highest but very variable cement percentages in the cement plant and very low percentages of cement during reinforcement work and pouring.

  18. Timing of the deglaciation and the late-glacial vegetation development on the Pandivere Upland, North Estonia

    Directory of Open Access Journals (Sweden)

    L. Amon

    2016-12-01

    Full Text Available In this study, the deglaciation chronology of the Pandivere Upland is defined, and the late-glacial vegetation trends of north-eastern Estonia are summarised. The multi-proxy study includes accelerated mass spectrometry 14 C dating, plant macrofossil, magnetic susceptibility, loss-on-ignition and grain-size distribution data of the lacustrine sediment record from one previously unpublished study site (Kursi, and the study discusses the results in combination with five previously published study locations from the area. The results indicate that the deglaciation of the Pandivere Upland started at approximately 14 200 cal. yr BP and was completed by 13 800 cal. yr BP. The ice recession rate was approximately 180 m yr -1 . Based on these new radiocarbon dates, the Baltic Ice Lake stage A 1 submerged the northern and western ice-free areas of Estonia by ca. 13 800 cal. yr BP. The prevalent vegetation type in north-eastern Estonia during the late-glacial period was tundra with local variations in the dominant shrub species. The region remained treeless until the Holocene.

  19. Colorectal cancer and non-malignant respiratory disease in asbestos cement and cement workers

    International Nuclear Information System (INIS)

    Jacobsson, K.

    1993-09-01

    Radiologically visible parenchymal changes (small opacities >= 1/0;ILO 1980 classification) were present in 20% of a sample of workers (N=174), employed for 20 years (median) in an asbestos cement plant. Exposure-response relationships were found, after controlling for age and smoking habits. In a sample of asbestos cement workers with symptoms and signs suggestive of pulmonary disease (N=33), increased lung density measured by x-ray computed tomography, and reduced static lung volumes and lung compliance was found. In a cohort of asbestos cement workers (N=1.929) with an estimated median exposure of 1.2 fibres/ml, the mortality from non-malignant respiratory disease was increased in comparison to a regional reference cohort (N=1.233). A two-to three-fold increase of non-malignant respiratory mortality was noted among workers employed for more than a decade in the asbestos cement plant, compared to cement workers (N=1.526), who in their turn did not experience and increased risk compared to the general population. In the cohorts of asbestos cement and cement workers, there was a tow-to three-fold increased incidence of cancer in the right part of the colon, compared to the general population as well as to external reference cohorts of other industrial workers (N=3.965) and fishermen (N=8.092). A causal relation with the exposure to mineral dust and fibres was supported by the findings of higher risk estimated in subgroups with high cumulated asbestos doses or longer duration of cement work. The incidence of cancer in the left part of the colon was not increased. Morbidity data, but not mortality data, disclosed the subsite-specific risk pattern. Both asbestos cement workers and cement workers has an increased incidence of rectal cancer, compared with the general population, and with the fishermen. The risk was, however, of the same magnitude among the other industrial workers. 181 refs

  20. Efficiency Assessment of Support Mechanisms for Wood-Fired Cogeneration Development in Estonia

    Science.gov (United States)

    Volkova, Anna; Siirde, Andres

    2010-01-01

    There are various support mechanisms for wood-fired cogeneration plants, which include both support for cogeneration development and stimulation for increasing consumption of renewable energy sources. The efficiency of these mechanisms is analysed in the paper. Overview of cogeneration development in Estonia is given with the focus on wood-fired cogeneration. Legislation acts and amendments, related to cogeneration support schemes, were described. For evaluating the efficiency of support mechanisms an indicator - fuel cost factor was defined. This indicator includes the costs related to the chosen fuel influence on the final electricity generation costs without any support mechanisms. The wood fuel cost factors were compared with the fuel cost factors for peat and oil shale. For calculating the fuel cost factors, various data sources were used. The fuel prices data were based on the average cost of fuels in Estonia for the period from 2000 till 2008. The data about operating and maintenance costs, related to the fuel type in the case of comparing wood fuel and oil shale fuel were taken from the CHP Balti and Eesti reports. The data about operating and maintenance costs used for peat and wood fuel comparison were taken from the Tallinn Elektrijaam reports. As a result, the diagrams were built for comparing wood and its competitive fuels. The decision boundary lines were constructed on the diagram for the situation, when no support was provided for wood fuels and for the situations, when various support mechanisms were provided during the last 12 years.

  1. Insect pests and their natural enemies on spring oilseed rape in Estonia : impact of cropping systems

    Directory of Open Access Journals (Sweden)

    E. VEROMANN

    2008-12-01

    Full Text Available To investigate the impact of different cropping systems, the pests, their hymenopteran parasitoids and predatory ground beetles present in two spring rape crops in Estonia, in 2003, were compared. One crop was grown under a standard (STN cropping system and the other under a minimised (MIN system. The STN system plants had more flowers than those in the MIN system, and these attracted significantly more Meligethes aeneus, the only abundant and real pest in Estonia. Meligethes aeneus had two population peaks: the first during opening of the first flowers and the second, the new generation, during ripening of the pods. The number of new generation M. aeneus was almost four times greater in the STN than in the MIN crop. More carabids were caught in the MIN than in STN crop. The maximum abundance of carabids occurred two weeks before that of the new generation of M. aeneus, at the time when M. aeneus larvae were dropping to the soil for pupation and hence were vulnerable to predation by carabids.

  2. The need and possible options for the use of renewable energy in Estonia

    International Nuclear Information System (INIS)

    Merdikes, M.; Kivistik, J.

    2002-01-01

    The decrease in fossil fuel and the environmental problems arising from their burning force the mankind to change the structure of energy production. In the Estonian primary energy balance of renewable natural resources wood and peat are on the first place with the percentage of ca 11%. Wind, water and solar energy have not up till now been widely used in Estonia. The foundation of a wind plant and the construction of bioenergy boiler plants are promising from the financial point of view. For the feedstock of bioenergy production, waste from logging and timber industry, energy fast-growing trees and grasses, bulrush and biogas produced by fermentation of organic matter, could be used. One of the options is to produce energy field crops - rape and turnip rape. The authors hope that this paper will emphasise the importance of conducting more extensive research of renewable energy resources and the introduction of such projects. (author)

  3. Review of technologies for mercury removal from flue gas from cement production processes

    DEFF Research Database (Denmark)

    Zheng, Yuanjing; Jensen, Anker Degn; Windelin, Christian

    2012-01-01

    sources of mercury in the cement kiln flue gas. Cement plants are quite different from power plants and waste incinerators regarding the flue gas composition, temperature, residence time, and material circulation. Cement kiln systems have some inherent ability to retain mercury in the solid materials due...... to the adsorption of mercury on the solids in the cold zone. However, recirculation of the kiln dust to the kiln will cause release of the captured mercury. The mercury chemistry in cement kiln systems is complicated and knowledge obtained from power plants and incinerators cannot be directly applied in cement...

  4. The use of mosses in air pollution monitoring in Estonia

    Energy Technology Data Exchange (ETDEWEB)

    Liiv, S.; Eensaar, A. [Academy of Sciences of Estonia, Tallinn (Estonia). Tallinn Botanic Garden

    1995-12-31

    Mosses Pleurozium schreberi and Hylocomium splendens have been proposed as biomonitors of atmospheric heavy metals. These mosses are wide-used in biomonitoring studies in Scandinavia as well as in other Nordic countries. Some methodical problems of bryoindication, e.g. other factors than the adsorption of precipitation which influence element concentrations in mosses have been studied in Scandinavia as well. Methodical study for determining the intrasite, local variability in Estonia was started in 1991. Despite of the used uniform methodics in sampling, cleaning, digesting and chemical analysing of moss samples in the same laboratory there is high variability of the content of elements at the reference area. There are many reasons for this variability - errors from instrumental procedures (analytical steps in chemical analysing), biological deviation, etc. In this article the results of the methodical study of intrasite variability of As, Cd, Cr, Cu, Fe, Ni, Pb, Zn and V in mosses at reference areas of different deposition level in Estonia are presented. The intrasite variability of elemental content in mosses at the reference areas is taken into account in mapping the territorial distribution of the content of elements in mosses, samples of which were collected during the joint Finnish-Estonian-Russian biomonitoring project in 1992 in a more dense network compared with the 1989 and 1990 national moss surveys in Estonia in order to describe more accurately the pollution situation in highly polluted north-eastern Estonia

  5. Why Do People Engage in Corruption? The Case of Estonia

    Science.gov (United States)

    Tavits, Margit

    2010-01-01

    This study uses survey data for 2004 on the general public (N = 788) and public officials (N = 791) in the young post-communist democracy of Estonia to examine individual-level determinants of corruption. The results indicate that both public officials and citizens are more likely to engage in corruption when they do not define corruption as…

  6. Saksa press käsitleb Estonia huku filmi blufina

    Index Scriptorium Estoniae

    2003-01-01

    Saksamaal esilinastus poliitiline põnevusfilm "Balti torm" ("Baltic Storm"), mis kujutab parvlaev "Estonia" hukku venelaste vandenõu tulemusena. Produtsendid on Jutta Rabe, Kaj Holmberg ja Birgit Stein, režissöör ja üks stsenariste Reuben Leder. Filmi vaieldavast konteptsioonist ja vastukajadest Saksa ajakirjanduses. Ka Eesti suursaadiku Riina Kionka arvamus

  7. Estonia hukk jõuab suvel kinodesse / Tarmo Michelson

    Index Scriptorium Estoniae

    Michelson, Tarmo, 1975-

    2002-01-01

    Nädal tagasi alustati Berliinis poliitilise põnevusfilmi "Baltic Storm" võtetega, mis kujutab parvlaev "Estonia" hukku venelaste vandenõu tulemusena. Produtsendid on Jutta Rabe ja Kaj Holmberg, režissöör Reuben Leder, peaosades Greta Scacchi ja Jürgen Prochnow

  8. A 13th-century kettlehat from Kodasoo, Estonia

    Directory of Open Access Journals (Sweden)

    Mäll, Jaak

    2011-12-01

    Full Text Available The oldest surviving helmet from Estonia is a 13th-century kettlehat found near village of Kodasoo in northern Estonia. Three samples from different parts of the kettlehat were investigated in a metallographic study. The raw material of the Kodasoo kettlehat was a slag-rich iron of heterogeneous carbon content. It was improved by folding and forge-welding it at least three times, resulting in layered structure with more uniformly distributed carbon content.

    El casco más antiguo encontrado en Estonia es un «chapel de fer» del siglo XIII que proviene de cerca de la aldea de Kodasoo, en el Norte de Estonia. Tres muestras de diversas partes del casco fueron investigadas mediante un estudio metalográfico. El material original del casco de Kodasoo era un hierro de contenido de carbono heterogéneo y con abundantes inclusiones de escoria. Se intentó mejorar su calidad mediante forja, doblándolo y soldándolo a la calda por lo menos tres veces, dando como resultado una estructura estratificada, con el contenido de carbono distribuido más uniformemente.

  9. Elegantne ja värske Rahvusooper Estonia / Maris Takk

    Index Scriptorium Estoniae

    Takk, Maris

    2006-01-01

    Rahvusooper Estonia publikuruumide renoveerimine. Sisearhitektid Juta Lember ja Aulo Padar, SAB Lember & Padar. Arhitektuurse projekti autor Indrek Suigusaar (AB Pluss). Eesti Sisearhitektide Liidu 2005. a. ajaloolise interjööri preemia. J. Lemberist ja A. Padarist, nende tähtsamad tööd, autasud. Ill.: plaan, 16 värv. vaadet, fotod sisearhitektidest

  10. Cryptosporidiosis - an occupational risk and a disregarded zoonosis in Estonia

    DEFF Research Database (Denmark)

    Enemark, Heidi; Ståhl, Marie; Lassen, Brian

    2014-01-01

    Background Cases of cryptosporidiosis have not been officially reported in Estonia after the year 2000, and the disease appears to be either under-diagnosed or under-reported. Findings Based on a human case of cryptosporidiosis contracted during faecal sampling in dairy farms, cattle considered t...

  11. The use of mosses in air pollution monitoring in Estonia

    Energy Technology Data Exchange (ETDEWEB)

    Liiv, S; Eensaar, A [Academy of Sciences of Estonia, Tallinn (Estonia). Tallinn Botanic Garden

    1996-12-31

    Mosses Pleurozium schreberi and Hylocomium splendens have been proposed as biomonitors of atmospheric heavy metals. These mosses are wide-used in biomonitoring studies in Scandinavia as well as in other Nordic countries. Some methodical problems of bryoindication, e.g. other factors than the adsorption of precipitation which influence element concentrations in mosses have been studied in Scandinavia as well. Methodical study for determining the intrasite, local variability in Estonia was started in 1991. Despite of the used uniform methodics in sampling, cleaning, digesting and chemical analysing of moss samples in the same laboratory there is high variability of the content of elements at the reference area. There are many reasons for this variability - errors from instrumental procedures (analytical steps in chemical analysing), biological deviation, etc. In this article the results of the methodical study of intrasite variability of As, Cd, Cr, Cu, Fe, Ni, Pb, Zn and V in mosses at reference areas of different deposition level in Estonia are presented. The intrasite variability of elemental content in mosses at the reference areas is taken into account in mapping the territorial distribution of the content of elements in mosses, samples of which were collected during the joint Finnish-Estonian-Russian biomonitoring project in 1992 in a more dense network compared with the 1989 and 1990 national moss surveys in Estonia in order to describe more accurately the pollution situation in highly polluted north-eastern Estonia

  12. The composition of surrogate and illegal alcohol products in Estonia.

    Science.gov (United States)

    Lang, Katrin; Väli, Marika; Szucs, Sándor; Adány, Róza; McKee, Martin

    2006-01-01

    To identify the composition of illegal and surrogate alcohol products consumed in Estonia. The initial source of information was a series of visits made in August 2005 to a soup kitchen in central Tartu, Estonia. Individuals were asked for brief details of their personal circumstances, what they normally drank, and in addition they were asked to bring samples of the substances they usually consumed. In other cases, the substances identified were purchased by the investigators or from informal contacts in north-eastern part of Estonia, an area that is well known for illegal alcohol consumption. Samples were tested for chemical contents. We identified a range of alcohol-containing substances that are consumed, although, not intended for consumption. These comprised medicinal products, aftershaves, illegally produced spirits, and fire-lighting fuel. The medicinal compounds contained, on average, 67% ethanol by volume; the aftershaves contained slightly less. Both were typically pure, with a few containing detectable quantities of isoamyl alcohol. The illegally produced alcohol contained, on average, 43% ethanol by volume, ranging from 32 to 53%. However, many also contained detectable quantities of long chain alcohols. These substances are half the price or less of commercial vodka, with fire lighting fuels especially inexpensive. There is in Estonia a range of alcohol-containing substances easily available at low cost. Some contain substantially higher concentrations of ethanol than commercial spirits and others also contain toxic long chain alcohols.

  13. Estonia juubelihooaeg tuleb tavalisest sisukam / Hille Tänavsuu

    Index Scriptorium Estoniae

    Tänavsuu, Hille, 1941-2014

    2005-01-01

    Rahvusooperi Estonia 100. hooaja etendustest: G. Verdi "Othello", G. Puccini ooper "Tosca", Rene Eespere ooper "Gurmaanid-2", P. Mascagni "Talupoja au", R. Leoncavallo "Pajatsid", W. A. Mozarti ooper "Don Giovanni" ja ooperi "La clemenza di Tito" kontsertettekanne, Tiit Härmi ballett "Kameeliadaam", Ludvig Minkuse ballett "Don Quijote". Osavõtust Dalhalla ooperifestivalist Rootsis Puccini ooperiga "Tosca" ja Cannito/Schiavoni balletiga "Cassandra"

  14. Estonia näitas uut logo / Andres Keil

    Index Scriptorium Estoniae

    Keil, Andres, 1974-

    2004-01-01

    Ooperiteatri uue logo autor on Kristjan Kirsfeldt. Liis Kolle lavastab G. Rossini ooperi "Sinjoor Bruschino ehk Poeg juhuse tahtel", kunstnikud Liina Keevallik ja Reili Evart. 2. juunil Rahvusooperis etendunud rahvusooperi näiteringi "Welcome to Estonia" Neeme Kuninga kirjutatud ja lavastatud muusikalist "Minu veetlev Eedi".

  15. PSD Determination, Portland Cement Plant

    Science.gov (United States)

    This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

  16. VUJE experience with cementation of liquid and wet radioactive waste

    International Nuclear Information System (INIS)

    Kravarik, Kamil; Holicka, Zuzana; Pekar, Anton; Zatkulak, Milan

    2011-01-01

    Liquid and wet LLW generated during operation as well as decommissioning of NPPs is treated with different methods and fixed in a suitable fixation matrix so that a final product meets required criteria for its disposal in a final repository. Cementation is an important process used for fixation of liquid and wet radioactive waste such as concentrate, spent resins and sludge. Active cement grout is also used for fixation of low level solid radioactive waste loaded in final packing containers. VUJE Inc. has been engaged in research of cementation for long. The laboratory for analyzing radioactive waste properties, prescription of cementation formulation and estimation of final cement product properties has been established. Experimental, semi-production cementation plant has been built to optimize operation parameters of cementation. VUJE experience with cementation of liquid and wet LLW is described in the presented paper. VUJE has assisted in commissioning of Jaslovske Bohunice Treatment Centre. Cement formulations for treatment of concentrate, spent resins and sludge have been developed. Research studies on the stability of a final concrete packaging container for disposal in repository have been performed. Gained experience has been further utilized for design and manufacture of several cementation plants for treatment of various liquid and wet LLW. Their main technological and technical parameters as well as characterization of treated waste are described in the paper. Applications include the Mochovce Final Treatment Centre, Movable Cementation Facility utilizing in-drum mixing for treatment of sludge, Cementation Facility for treatment of tritiated water in Latvia and Cementation Facility for fixation of liquid and solid institutional radioactive waste in Bulgaria, which utilizes lost stirrer mixer. (author)

  17. Personal exposure to inhalable cement dust among construction workers.

    Science.gov (United States)

    Peters, Susan; Thomassen, Yngvar; Fechter-Rink, Edeltraud; Kromhout, Hans

    2009-01-01

    Objective- A case study was carried out to assess cement dust exposure and its determinants among construction workers and for comparison among workers in cement and concrete production.Methods- Full-shift personal exposure measurements were performed and samples were analysed for inhalable dust and its cement content. Exposure variability was modelled with linear mixed models.Results- Inhalable dust concentrations at the construction site ranged from 0.05 to 34 mg/m(3), with a mean of 1.0 mg/m(3). Average concentration for inhalable cement dust was 0.3 mg/m(3) (GM; range 0.02-17 mg/m(3)). Levels in the ready-mix and pre-cast concrete plants were on average 0.5 mg/m(3) (GM) for inhalable dust and 0.2 mg/m(3) (GM) for inhalable cement dust. Highest concentrations were measured in cement production, particularly during cleaning tasks (inhalable dust GM = 55 mg/m(3); inhalable cement dust GM = 33 mg/m(3)) at which point the workers wore personal protective equipment. Elemental measurements showed highest but very variable cement percentages in the cement plant and very low percentages during reinforcement work and pouring. Most likely other sources were contributing to dust concentrations, particularly at the construction site. Within job groups, temporal variability in exposure concentrations generally outweighed differences in average concentrations between workers. 'Using a broom', 'outdoor wind speed' and 'presence of rain' were overall the most influential factors affecting inhalable (cement) dust exposure.Conclusion- Job type appeared to be the main predictor of exposure to inhalable (cement) dust at the construction site. Inhalable dust concentrations in cement production plants, especially during cleaning tasks, are usually considerably higher than at the construction site.

  18. Centralized cement solidification technique for low-level radioactive wastes

    International Nuclear Information System (INIS)

    Matsuda, Masami; Nishi, Takashi; Izumida, Tatsuo; Tsuchiya, Hiroyuki.

    1996-01-01

    A centralized cement solidification system has been developed to enable a single facility to solidify such low-level radioactive wastes as liquid waste, spent ion exchange resin, incineration ash, and miscellaneous solid wastes. Since the system uses newly developed high-performance cement, waste loading is raised and deterioration of waste forms after land burial prevented. This paper describes the centralized cement solidification system and the features of the high-performance cement. Results of full-scale pilot plant tests are also shown from the viewpoint of industrial applicability. (author)

  19. Communication of 20 October 2003 from the Permanent Mission of the Republic of Estonia to the International Atomic Energy Agency regarding Estonia's nuclear policies and practices

    International Nuclear Information System (INIS)

    2004-01-01

    The Director General has received a Note Verbale of 20 October 2003 from the Permanent Mission of the Republic of Estonia providing information about the nuclear policies and practices of the Republic of Estonia. In light of the wish expressed in the Note Verbale, its text is attached hereto

  20. 77 FR 42367 - National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing...

    Science.gov (United States)

    2012-07-18

    ... and 63 National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing... Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing Industry and Standards of... manufacturing plants. Federal government Not affected. State/local/tribal government.... Portland cement...

  1. Solidification of liquid radioactive concentrates by fixation with cement

    International Nuclear Information System (INIS)

    Pekar, A.; Breza, M.; Timulak, J.; Krajc, T.

    1985-01-01

    In testing the technology of liquid radioactive wastes cementation, the effect was mainly studied of the content of boric acid and its salts on cement solidification, the effect of additives on radionuclide leachability and the effect of the salt content on the cementation product. On the basis of experimental work carried out on laboratory scale with model samples and samples of radioactive concentrate from the V-1 nuclear power plant, the following suitable composition of the cementation mixture was determined: 40% Portland cement, 40% zeolite containing material and 20% power plant ash. The most suitable ratio of liquid radioactive wastes and the cementation mixture is 0.5. As long as in such case the salt content of the concentrate ranges between 20 and 25%, the cementation product will have a maximum salt content of 10% and a leachability of the order of 10 -3 to 10 -4 g/cm 2 per day with a mechanical strength allowing safe handling. It was also found that the quality processing of the cement paste with degassing, e.g., by vibration, is more effective for the production of a pore-free cementation product than the application of various additives which are supposed to eliminate pore formation. (Z.M.)

  2. Estonia plans to build nuclear power plant / Jana Belugina

    Index Scriptorium Estoniae

    Belugina, Jana

    2009-01-01

    Eesti Energia on tuumaelektrijaama ehitamiseks välja valinud kuus asukohta. Seadusandlikke otsuseid tuumaelektrijaama ehitamise kohta saab vastu võtta alates 2014. aastast ning tuumareaktori valmimise aeg on 2025. aasta

  3. Alternative Fuel for Portland Cement Processing

    Energy Technology Data Exchange (ETDEWEB)

    Schindler, Anton K; Duke, Steve R; Burch, Thomas E; Davis, Edward W; Zee, Ralph H; Bransby, David I; Hopkins, Carla; Thompson, Rutherford L; Duan, Jingran; ; Venkatasubramanian, Vignesh; Stephen, Giles

    2012-06-30

    The production of cement involves a combination of numerous raw materials, strictly monitored system processes, and temperatures on the order of 1500 °C. Immense quantities of fuel are required for the production of cement. Traditionally, energy from fossil fuels was solely relied upon for the production of cement. The overarching project objective is to evaluate the use of alternative fuels to lessen the dependence on non-renewable resources to produce portland cement. The key objective of using alternative fuels is to continue to produce high-quality cement while decreasing the use of non-renewable fuels and minimizing the impact on the environment. Burn characteristics and thermodynamic parameters were evaluated with a laboratory burn simulator under conditions that mimic those in the preheater where the fuels are brought into a cement plant. A drop-tube furnace and visualization method were developed that show potential for evaluating time- and space-resolved temperature distributions for fuel solid particles and liquid droplets undergoing combustion in various combustion atmospheres. Downdraft gasification has been explored as a means to extract chemical energy from poultry litter while limiting the throughput of potentially deleterious components with regards to use in firing a cement kiln. Results have shown that the clinkering is temperature independent, at least within the controllable temperature range. Limestone also had only a slight effect on the fusion when used to coat the pellets. However, limestone addition did display some promise in regards to chlorine capture, as ash analyses showed chlorine concentrations of more than four times greater in the limestone infused ash as compared to raw poultry litter. A reliable and convenient sampling procedure was developed to estimate the combustion quality of broiler litter that is the best compromise between convenience and reliability by means of statistical analysis. Multi-day trial burns were conducted

  4. Estonia katastroofis hukkunute omaste seisukohad ja palve seoses USA presidendi George W. Bushi visiidiga

    Index Scriptorium Estoniae

    2006-01-01

    Estonia protsessiühingu esimehe Helje Kaskeli ja Estonia Hukupõhjuste Väljaselgitamise Mittetulundusühingu esimehe Ülo Veide pöördumises president Toomas Hendrik Ilvese poole tuuakse esile katastroofis hukkunute omaste seisukohad. Ilmunud ka: Kesknädal 29. nov. 2006, lk. 4-5, pealk.: Ilves, avita! Estonia katastroofis hukkunute omaste palvekiri Toomas Hendrik Ilvesele; Vaba Eesti Sõna 30. nov. 2006, lk. 3, 10, pealk.: Avalik kiri Eesti Vabariigi presidendile Toomas H. Ilvesele

  5. Kohtumisel Bushiga tuleks tõstatada ka Estonia huku teema / Allar Viivik

    Index Scriptorium Estoniae

    Viivik, Allar

    2006-01-01

    Parvlaeval Estonia hukkunute omaste ühendused avaldasid oma pöördumises Toomas Hendrik Ilvesele soovi, et president arutaks kohtumisel USA presidendi George W. Bushiga USA julgeolekuagentuuri NSA käsutuses olevate laevahukku puudutavate salastatud dokumentide üleandmist Eestile. Pöördumisele on alla kirjutanud Estonia Litigation Associationi esimees Helje Kaskel ja Estonia Hukupõhjuste Väljaselgitamise Mittetulundusühingu (EHVM) juht Ülo Veide

  6. Air quality management on the areas of North-East Estonia

    Energy Technology Data Exchange (ETDEWEB)

    Liblik, V.; Kundel, H.; Raetsep, A. [Estonian Academy of Sciences, Tallinn (Estonia). North-East Estonian Dept.

    1995-12-31

    Most biggest polluters of atmospheric air among Estonian enterprises are located in the north-eastern part of republic. Volatile gases, vapours and fly ash from thermal power plants, chemical and other industries form a considerable aerotechnogenic load upon landscapes and dwelling regions, reaching also the areas of Gulf of Finland, and even the neighbouring states. Complicated pollution situation needs serious attention and systematic air quality control, assessing, forecasting and management, which is now organized on local, regional and state levels. It is well-known that for studies of various pollution situations the atmospheric dispersion models will be used. This present article deals with the special imitation system for maintenance of information about polluters and air contamination state in North-East (NE) Estonia, also for estimation of pollutants spreading and overground concentration fields by computer-based modelling. The system consists of regional Data Banks, imitation model for calculation of pollutants dispersion, common and application programs. (author)

  7. Air quality management on the areas of North-East Estonia

    International Nuclear Information System (INIS)

    Liblik, V.; Kundel, H.; Raetsep, A.

    1995-01-01

    Most biggest polluters of atmospheric air among Estonian enterprises are located in the north-eastern part of republic. Volatile gases, vapours and fly ash from thermal power plants, chemical and other industries form a considerable aerotechnogenic load upon landscapes and dwelling regions, reaching also the areas of Gulf of Finland, and even the neighbouring states. Complicated pollution situation needs serious attention and systematic air quality control, assessing, forecasting and management, which is now organized on local, regional and state levels. It is well-known that for studies of various pollution situations the atmospheric dispersion models will be used. This present article deals with the special imitation system for maintenance of information about polluters and air contamination state in North-East (NE) Estonia, also for estimation of pollutants spreading and overground concentration fields by computer-based modelling. The system consists of regional Data Banks, imitation model for calculation of pollutants dispersion, common and application programs. (author)

  8. Oil shale mining and processing impact on landscapes in north-east Estonia

    International Nuclear Information System (INIS)

    Toomik, Arvi; Liblik, Valdo

    1998-01-01

    As the world's largest commercial oil shale reserve, the Estonian Oil Shale Deposit has been exploited since 1916. As a result of mining, storing of solid wastes from the oil shale separation, combustion in the power plants and its thermal processing, the landscape in northeastern Estonia has been essentially changed and the man-made landforms have developed: the new microreliefs of natural and artificial structure are formed, as well as 'mountainous' and hilly reliefs in the form of waste heaps, ash plateaus, coke-ash dumps etc. Deformed (stable) and undeformed (unstable) areas from underground mining currently cover about 220km 2 . About 90km 2 (80%) of the area damaged by open pits are recultivated and reformed as forested and agricultural (grassland) areas. The total area occupied by solid waste has reached up to 26km 2 . New technogenic landscape units, i.e. made by technical means, will essentially influence the environment

  9. Air quality management on the areas of North-East Estonia

    Energy Technology Data Exchange (ETDEWEB)

    Liblik, V; Kundel, H; Raetsep, A [Estonian Academy of Sciences, Tallinn (Estonia). North-East Estonian Dept.

    1996-12-31

    Most biggest polluters of atmospheric air among Estonian enterprises are located in the north-eastern part of republic. Volatile gases, vapours and fly ash from thermal power plants, chemical and other industries form a considerable aerotechnogenic load upon landscapes and dwelling regions, reaching also the areas of Gulf of Finland, and even the neighbouring states. Complicated pollution situation needs serious attention and systematic air quality control, assessing, forecasting and management, which is now organized on local, regional and state levels. It is well-known that for studies of various pollution situations the atmospheric dispersion models will be used. This present article deals with the special imitation system for maintenance of information about polluters and air contamination state in North-East (NE) Estonia, also for estimation of pollutants spreading and overground concentration fields by computer-based modelling. The system consists of regional Data Banks, imitation model for calculation of pollutants dispersion, common and application programs. (author)

  10. Advanced cementation concepts

    International Nuclear Information System (INIS)

    Howard, C.G.

    1989-10-01

    The purpose of this programme of work was to investigate whether improvements could be made to existing formulations for cement suitable for the immobilization of intermediate level radioactive waste. Two additives were selected, microsilica and limestone flour. Improvements to the cement were only slight. (author)

  11. Preparation of hydraulic cement

    Energy Technology Data Exchange (ETDEWEB)

    1921-08-28

    A process for the preparation of hydraulic cement by the use of oil-shale residues is characterized in that the oil-shale refuse is mixed with granular basic blast-furnace slag and a small amount of portland cement and ground together.

  12. Low force cementation.

    Science.gov (United States)

    Wilson, P R

    1996-07-01

    The marginal adaptation of full coverage restorations is adversely affected by the introduction of luting agents of various minimum film thicknesses during the cementation process. The increase in the marginal opening may have long-term detrimental effects on the health of both pulpal and periodontal tissues. The purpose of this study was to determine the effects of varying seating forces (2.5, 12.5, 25 N), venting, and cement types on post-cementation marginal elevation in cast crowns. A standardized cement space of 40 microns was provided between a machined gold crown and a stainless steel die. An occlusal vent was placed that could be opened or closed. The post-cementation crown elevation was measured, following the use of two commercially available capsulated dental cements (Phosphacap, and Ketac-cem Applicap). The results indicate that only the combination of Ketac-Cem Applicap and crown venting produced post-cementation crown elevation of less than 20 microns when 12.5 N seating force was used. Higher forces (25 N) and venting were required for comparable seating when using Phosphacap (19 microns). The amount of force required to allow maximum seating of cast crowns appears to be cement specific, and is reduced by effective venting procedures.

  13. Rahmaninov ja Saint-Saens Estonia kontserdisaalis / Tiina Õun

    Index Scriptorium Estoniae

    Õun, Tiina, 1954-

    2005-01-01

    18. novembril Estonia kontserdisaalis toimuvast Sergei Rahmaninovi Klaverikontsert nr 2 ja "Kellad" ettekandest ja 29. novembril Toimuvast Camille Saint-Saensi ooperi "Simson ja Delila" kontsertettekandest

  14. Sajandi sündmus : Estonia teater jõudis Financial Timesi / Krister Kivi

    Index Scriptorium Estoniae

    Kivi, Krister, 1975-

    2002-01-01

    Maailmakuulus majandusleht Financial Times avaldas 4. jaanuaril ajakirjanik George Loomis'e artikli, mis kajastab Rahvusooperis Estonia 14. detsembril 2001 esietendunud Carl Orffi ooperit "Tark naine"

  15. Berliner Zeitung annab Estonia-filmile hävitava hinnangu

    Index Scriptorium Estoniae

    2003-01-01

    Saksamaal esilinastus poliitiline põnevusfilm "Balti torm" ("Baltic Storm"), mis kujutab parvlaev "Estonia" hukku venelaste vandenõu tulemusena. Filmi vaieldavast konteptsioonist ja vastukaja Saksa ajakirjanduses

  16. Building up the radiation protection infrastructure in Estonia

    International Nuclear Information System (INIS)

    Lust, Merle; Muru, Karin

    2008-01-01

    This paper will provide a timeline overview of the of radiation protection infrastructure following the 1999 declaration of independence. In Estonia, an independent competent authority was inaugurated in 1996 and the first Radiation Act was approved by Parliament the following year, in 1997. This paper will address several important factors and the means which promoted development. International cooperation was and remains an essential factor worthy of discussion. For example participation in International Atomic Energy Agency technical co-operation programme and co-operation with neighbouring countries greatly facilitated greatly the development. Political choices and the long term goal of accession to the European Union had great importance to the process also. Today, the Republic of Estonia is member of European Union and has built up a well functioning radiation protection system according the international standards and requirements. This paper is intended to share the experience and to facilitate the learning process. (author)

  17. The tourism image of Estonia in Spain: a formulative approach

    Directory of Open Access Journals (Sweden)

    Katlin Savva

    2015-01-01

    Full Text Available We are living in an environment, where information flow is freer than ever. Nowadays everyone has access to global news and can make their own conclu-sions based on the perceived image. Therefore, the role of perception and image is becoming more important for different countries to attract visitors and in-vestors. Tourism is a way of selling the image of a country and the reputation and word of mouth generated from tourism activities are priceless to the image of a destination. This paper analyzes the case of Estonia, which is an emerging tourism market and quite new and unknown for Spain. The authors try to accent the importance of direct promotion, through a survey carried out to 341 Spanish people in Madrid. The result from this quantitative and formulative research method is that Estonia has to promote its tourism image better if the country wants to attract the Spanish tourist.

  18. The preventing of illicit trafficking of radioactive materials in Estonia

    International Nuclear Information System (INIS)

    Velbri, T.; Aasmann, L.

    1998-01-01

    This paper explains the situation of legislation, practical border-control and equipment of different relevant authorities dealing with the control of radioactive materials in Estonia. The overview of legislation concerning radiation and radiation protection is given. The roles of Estonian Customs Authority, Estonian border Guard, National Rescue Board and Police Authority in the preventing of illicit trafficking of radioactive materials are shown. The incidents of illicit trafficking of radioactive materials are listed. Also the most important border-crossing points and the types of equipment used there are shown. Finally the problems of controlling the borders in Estonia and the future plans in order to make the controlling system more efficient are discussed. (author)

  19. PRODUCTIVITY PERFORMANCE OF ESTONIA IN A GROWTH ACCOUNTING APPROACH

    Directory of Open Access Journals (Sweden)

    Vivien MOLNAR

    2016-12-01

    Full Text Available This paper aims to contribute to a better understanding of the economic growth tendencies in Estonia and other formal post-socialist countries and the interaction between productivity growth and their determinants after the transition decades. So this paper is structured as follows. Firstly we will introduce an alternative growth accounting method to determine the components of productivity growth based on this concept. In Section we will also provide our empirical results in Estonia, Latvia, Lithuania and Hungary compared to the EU-15 countries between 1990 and 2011 how TFP (Total Factor Productivity, Physical and Labour Capital Accumulation can contribute to (increase or decrease economic performance of each country. Finally, we can conclude that the relationship between labour and output growth per capita has obviously and temporarily changed after the mid-1990s, which could be determined by the increasing role of such socio-economic factors as technological changes, capital accumulation and demographical fluctuations etc.

  20. Some problems of oil shale retorting in Estonia

    International Nuclear Information System (INIS)

    Oepik, I.

    1994-01-01

    Oil shale in Estonia will be competitive in the long term as a primary resource for power generating. The price of energy of Estonian oil shale is at present approximately 4 times lower than of coal. The price of electricity is anticipated to grow up to EEK 1.0/kWh in year 2020. The electricity price EEK 0.2/kWh at present in Estonia does not include capital costs needed for refurbishing of Estonian oil-shale-consuming power stations between the years 2000-2010. While all the prices and calculations of the enterprise are presented with no inflation adjustment, the other operation costs of oil shale retorting are anticipated for the prognosed period to remain at the present level: power consumption kWh 280/t crude oils and other operation costs (excluding labour, raw material and power consumption) EEK 100/t of oil

  1. Analysis of Energy-Efficiency Opportunities for the Cement Industry in Shandong Province, China

    Energy Technology Data Exchange (ETDEWEB)

    Price, Lynn; Hasanbeigi, Ali; Lu, Hongyou; Wang, Lan

    2009-10-01

    China's cement industry, which produced 1,388 million metric tons (Mt) of cement in 2008, accounts for almost half of the world's total cement production. Nearly 40% of China's cement production is from relatively obsolete vertical shaft kiln (VSK) cement plants, with the remainder from more modern rotary kiln cement plants, including plants equipped with new suspension pre-heater and pre-calciner (NSP) kilns. Shandong Province is the largest cement-producing Province in China, producing 10% of China's total cement output in 2008. This report documents an analysis of the potential to improve the energy efficiency of NSP kiln cement plants in Shandong Province. Sixteen NSP kiln cement plants were surveyed regarding their cement production, energy consumption, and current adoption of 34 energy-efficient technologies and measures. Plant energy use was compared to both domestic (Chinese) and international best practice using the Benchmarking and Energy Saving Tool for Cement (BEST-Cement). This benchmarking exercise indicated an average technical potential primary energy savings of 12% would be possible if the surveyed plants operated at domestic best practice levels in terms of energy use per ton of cement produced. Average technical potential primary energy savings of 23% would be realized if the plants operated at international best practice levels. Energy conservation supply curves for both fuel and electricity savings were then constructed for the 16 surveyed plants. Using the bottom-up electricity conservation supply curve model, the cost-effective electricity efficiency potential for the studied cement plants in 2008 is estimated to be 373 gigawatt hours (GWh), which accounts for 16% of total electricity use in the 16 surveyed cement plants in 2008. Total technical electricity-saving potential is 915 GWh, which accounts for 40% of total electricity use in the studied plants in 2008. The fuel conservation supply curve model shows the total

  2. Radiological Cs-137 accidents/incidents in Estonia

    International Nuclear Information System (INIS)

    Sinisso, Mark

    1997-01-01

    Two radiological accidents/incidents in Estonia are reported. The first -21 October 1994, three brothers entered the Tammiku repository and stole a radioactive Cs-137 source and received dangerous doses of radiation. The other incident (early 1995) involved an abandoned source - a discarded metal cylinder containing Cs-137. Chronologies and factual data are considered for both events. Concise descriptions of the incidents, a medical overview of the fate of injured people and lessons learned are presented

  3. Radiological Cs-137 accidents/incidents in Estonia

    Energy Technology Data Exchange (ETDEWEB)

    Sinisso, Mark [Ministry of Foreign Affairs, Tallin (Estonia)

    1997-12-31

    Two radiological accidents/incidents in Estonia are reported. The first -21 October 1994, three brothers entered the Tammiku repository and stole a radioactive Cs-137 source and received dangerous doses of radiation. The other incident (early 1995) involved an abandoned source - a discarded metal cylinder containing Cs-137. Chronologies and factual data are considered for both events. Concise descriptions of the incidents, a medical overview of the fate of injured people and lessons learned are presented

  4. Estonia ujub Saksamaa kinodesse / Andres Laasik, Heiki Suurkask

    Index Scriptorium Estoniae

    Laasik, Andres, 1960-2016

    2003-01-01

    Saksamaal Berliinis esilinastub pidulikult 13. oktoobril poliitiline põnevusfilm "Balti torm" ("Baltic Storm"), mis kujutab parvlaev "Estonia" hukku. Režissöör ja üks stsenariste on Reuben Leder, peaosades Greta Scacchi ja Jürgen Prochnow. Kaasa teeb ka Donald Sutherland USA kindrali rollis. Eesti näitlejaist teeb kaasa Rein Oja. Põhjamaades on filmi linastamine kahtluse all

  5. Emissions of metals and polychlorinated dibenzo(p)dioxins and furans (PCDD/Fs) from Portland cement manufacturing plants: inter-kiln variability and dependence on fuel-types.

    Science.gov (United States)

    Zemba, Stephen; Ames, Michael; Green, Laura; Botelho, Maria João; Gossman, David; Linkov, Igor; Palma-Oliveira, José

    2011-09-15

    Emissions from Portland cement manufacturing facilities may increase health risks in nearby populations and are thus subject to stringent regulations. Direct testing of pollutant concentrations in exhaust gases provides the best basis for assessing the extent of these risks. However, these tests (i) are often conducted under stressed, rather than typical, operating conditions, (ii) may be limited in number and duration, and (iii) may be influenced by specific fuel-types and attributes of individual kilns. We report here on the results of more than 150 emissions-tests conducted of two kilns at a Portland cement manufacturing plant in Portugal. The tests measured various regulated metals and polychlorinated dibenzo(p)dioxins and furans (PCDD/Fs). Stack-gas concentrations of pollutants were found to be highly variable, with standard deviations on the order of mean values. Emission rates of many pollutants were higher when coal was used as the main kiln fuel (instead of petroleum coke). Use of various supplemental fuels, however, had little effect on stack emissions, and few statistically significant differences were observed when hazardous waste was included in the fuel mix. Significant differences in emissions for some pollutants were observed between the two kilns despite their similar designs and uses of similar fuels. All measured values were found to be within applicable regulatory limits. Published by Elsevier B.V.

  6. How important is business ethics: evidence from Estonia

    Directory of Open Access Journals (Sweden)

    Natalja Gurvitsh

    2017-09-01

    Full Text Available How important is business ethics: evidence from Estonia During recent decades, more and more attention has been paid to business ethics. There seems to be an increasing interest in the non-financial aspects of business. Stakeholders all over the world express their concern about embedding the principles of professional and business ethics into companies’ everyday activities. The main subject of this research is business ethics and the purpose is to find out the im-portance of professional and business ethics and determine its place in the modern business world as seen by Estonian business students and practitioners. To achieve the goals, the authors conducted a survey among Estonian graduate and undergraduate accounting and business students at Tallinn University of Technology and Estonian business practitioners. 587 responses were collected in the process. This infor-mation was compiled and analyzed based on status, gender, age, and specialization. The survey revealed that in Estonia people are familiar with business ethics; however, it is not of great interest to them. The results also indicate that professional and business ethics merit more attention and should be included as a required course in the curriculum of Higher Education Institutions (HEIs. In general, business ethics in Estonia was not ranked as “high”, which was also the case for both professional ethics at the work-place/university and also the importance and necessity of ethics in the modern business world.

  7. Modified pavement cement concrete

    Science.gov (United States)

    Botsman, L. N.; Ageeva, M. S.; Botsman, A. N.; Shapovalov, S. M.

    2018-03-01

    The paper suggests design principles of pavement cement concrete, which covers optimization of compositions and structures at the stage of mixture components selection due to the use of plasticizing agents and air-retaining substances that increase the viability of a concrete mixture. It also demonstrates advisability of using plasticizing agents together with air-retaining substances when developing pavement concrete compositions, which provides for the improvement of physical and mechanical properties of concrete and the reduction of cement binding agent consumption thus preserving strength indicators. The paper shows dependences of the main physical-mechanical parameters of concrete on cement consumption, a type and amount of additives.

  8. Radioactive waste cementation

    International Nuclear Information System (INIS)

    Soriano B, A.

    1996-01-01

    This research was carried out to develop the most adequate technique to immobilize low and medium-activity radioactive waste. different brands of national cement were used, portland and pozzolanic cement. Prismatic and cylindrical test tubes were prepared with different water/cement (W/C) relationship. Additives such a as clay and bentonite were added in some other cases. Later, the properties of these test tubes were evaluated. Properties such as: mechanical resistance, immersion resistance, lixiviation and porosity resistance. Cement with the highest mechanical resistance values, 62,29 MPa was pozzolanic cement for a W/C relationship of 0,35. It must be mentioned that the other types of cements reached a mechanical resistance over 10 MPa, a value indicated by the international standards for transportation and storage of low and medium-activity radioactive waste at a superficial level. However, in the case of immersion resistance, Sol cement (portland type I) with a W/C relationship of 0,35 reached a compression resistance over 61,92 MPa; as in the previous cases, the other cements reached a mechanical resistance > 10 MPa. Regarding porosity, working with W/C relationships = 0,35 0,40 and 0,45, without additives and with additives, the percentage of porosity found for all cements is lower than 40% percentage indicated by international standards. With regard to the lixiviation test, pozzolanic cement best retained Cesium-137 and Cobalt-60, and increased its advantages when bentonite was added, obtaining a lixiviation rate of 2,02 x E-6 cm/day. Sol cement also improved its properties when bentonite was added and obtained a lixiviation rate of 2,84 x E-6 cm/day for Cesium-137. However, Cobalt-60 is almost completely retained with the 3 types of cement with or without additives, reaching the limits indicated by the international standards for the lixiviation rate of beta-gamma emitter < 5,00E-4 cm/day. Characterizing the final product involves the knowledge of its

  9. Tympanoplasty with ionomeric cement

    DEFF Research Database (Denmark)

    Kjeldsen, A D; Grøntved, A M

    2000-01-01

    with isolated erosion of the long incus process have been treated with a new surgical technique in which the ossicular chain was rebuilt with ionomeric cement. The results in hearing performance (mean pure-tone average (PTA) 0.5, 1 and 2 kHz) were evaluated pre- and post-surgery, and compared to those...... of > 10 dB, in 4 there was a slight improvement and in 2 a decline. The difference was not statistically significant. Hearing improvement using ionomeric cement in type II tympanoplasty was satisfactory. Reconstruction of the ossicular chain with ionomeric cement is recommended, as the procedure is easy...

  10. Opportunities for Energy Efficiency and Demand Response in the California Cement Industry

    Energy Technology Data Exchange (ETDEWEB)

    Olsen, Daniel; Goli, Sasank; Faulkner, David; McKane, Aimee

    2010-12-22

    This study examines the characteristics of cement plants and their ability to shed or shift load to participate in demand response (DR). Relevant factors investigated include the various equipment and processes used to make cement, the operational limitations cement plants are subject to, and the quantities and sources of energy used in the cement-making process. Opportunities for energy efficiency improvements are also reviewed. The results suggest that cement plants are good candidates for DR participation. The cement industry consumes over 400 trillion Btu of energy annually in the United States, and consumes over 150 MW of electricity in California alone. The chemical reactions required to make cement occur only in the cement kiln, and intermediate products are routinely stored between processing stages without negative effects. Cement plants also operate continuously for months at a time between shutdowns, allowing flexibility in operational scheduling. In addition, several examples of cement plants altering their electricity consumption based on utility incentives are discussed. Further study is needed to determine the practical potential for automated demand response (Auto-DR) and to investigate the magnitude and shape of achievable sheds and shifts.

  11. Factors affecting re-vegetation dynamics of experimentally restored extracted peatland in Estonia.

    Science.gov (United States)

    Karofeld, Edgar; Müür, Mari; Vellak, Kai

    2016-07-01

    Increasing human activity continues to threaten peatlands, and as the area of natural mires declines, our obligation is to restore their ecosystem functions. Several restoration strategies have been developed for restoration of extracted peatlands, including "The moss layer transfer method", which was initiated on the Tässi extracted peatland in central Estonia in May 2012. Three-year study shows that despite the fluctuating water table, rainfall events can compensate for the insufficient moisture for mosses. Total plant cover on the restoration area attained 70 %, of which ~60 % is comprised of target species-Sphagnum mosses. From restoration treatments, spreading of plant fragments had a significant positive effect on the cover of bryophyte and vascular plants. Higher water table combined with higher plant fragments spreading density and stripping of oxidised peat layer affected positively the cover of targeted Sphagnum species. The species composition in the restoration area became similar to that in the donor site in a natural bog. Based on results, it was concluded that the method approved for restoration in North America gives good results also in the restoration of extracted peatland towards re-establishment of bog vegetation under northern European conditions.

  12. Cementation of wastes with boric acid

    International Nuclear Information System (INIS)

    Tello, Cledola C.O.; Haucz, Maria Judite A.; Alves, Lilian J.L.; Oliveira, Arno H.

    2000-01-01

    In nuclear power plants (PWR) are generated wastes, such as concentrate, which comes from the evaporation of liquid radioactive wastes, and spent resins. Both have boron in their composition. The cementation process is one of the options to solidify these wastes, but the boron has a negative effect on the setting of the cement mixture. In this paper are presented the experiments that are being carried out in order to overcome this problem and also to improve the efficiency of the process. Simulated wastes were cemented using additives (clays, admixtures etc.). In the process and product is being evaluated the effect of the amount, type and addition order of the materials. The mixtures were selected in accordance with their workability and incorporated waste. The solidified products are monolithic without free water with a good mechanical resistance. (author)

  13. Late glacial multiproxy evidence of vegetation development and environmental change at Solova, southeastern Estonia

    Directory of Open Access Journals (Sweden)

    Amon, Leeli

    2010-06-01

    Full Text Available Reinvestigation of the late glacial Solova (Remmeski basin, based on plant macro­fossil and diatom record, AMS 14C chronology and sediment composition (loss-on-ignition and magnetic susceptibility data, provided information on vegetation history and palaeoenvironmental and palaeoclimatic changes since the time of the deglaciation of the area around 14 000 cal yr BP. The chronology of the sequence is based on seven AMS dates on terrestrial macrofossils, providing evidence of rapid sedimentation in between 14 000 and 13 500 cal yr BP. Loss-on-ignition data show a clear short-lived warming episode centred to 13 800 cal yr BP, tentatively correlated with the GI-1c warming of the event stratigraphy of the Last Termination in the North Atlantic region, which suggests that at least parts of the Haanja Heights were ice-free by 14 000 cal yr BP. Macrofossil evidence indicates Betula nana–Dryas octopetala-dominated open tundra communities with Saxifraga on dry ground, and Carex sp. and Juncus on wet ground at that time. The first evidence of the postglacial presence of tree birch (Betula pendula in Estonia is dated back to 13 500 cal yr BP. However, conifer remains were not found in the late glacial sediment sequence of Solova Bog. The late-Allerød (GI-1a organic deposits, which are quite typical of other parts of Estonia and indicate general warming, are missing at Solova, most probably due to a hiatus in sedimentation in this very small and shallow upland basin.

  14. Uudised : Estonia maja renoveerimisest. EMNi juhatuse tegevusest. Meredith Monki kontsert Tallinnas

    Index Scriptorium Estoniae

    2001-01-01

    7. märtsil kiitis rahvusooperi Estonia nõukogu heaks Estonia teatri- ja kontserdimaja renoveerimistööde tehnilise projekti. EMNi juhatuse koosolekul 27. veebr. arutati E. Teatri- ja Muusikamuuseumi perspektiive, muusikahariduse probleeme ja EMNi töösuundi. 20. märtsil esineb Tallinnas Sakala keskuses M. Monk

  15. Rahvusooperi Estonia 99. hooaeg algab nädala pärast / Christel Karits

    Index Scriptorium Estoniae

    Karits, Christel, 1966-

    2004-01-01

    Muusikaturu korraldamisest 18. sept. Estonia teatrihoone taga ajaloolisel turuplatsil. Katri Kaasik-Aaslavi ja Vaino Vahingu näidendi "Teatriromanss" (muusika arranzheerija ja pianist Olav Ehala) esietendusest Estonia kammersaalis 22. oktoobril. Giuseppe Verdi ooperi "Aida" etendamisest Rocca al Mare Onistar Tennisekeskuses 8.-10., 12.-17. oktoobril

  16. The Affective Dimension of Religion and Personal Happiness among Students in Estonia

    Science.gov (United States)

    Francis, Leslie J.; Elken, Ahto; Robbins, Mandy

    2012-01-01

    A sample of 150 students in Estonia (119 from a secular university and 31 from a Lutheran theological institute) completed the Oxford Happiness Measure and the Francis Scale of Attitude toward Christianity. The data show no significant correlation between these two variables; thus the findings challenge the generalizability to Estonia of the…

  17. Tosca Mikiveri mälestuseks. Estonia Turupäev 2007

    Index Scriptorium Estoniae

    2007-01-01

    Lavastaja Mikk Mikiveri 70. sünniaastapäeva tähistamisest Giacomo Puccini ooperi "Tosca" esietendusega 4. sept. Tartus Vanemuise väikeses majas. Rahvusooper Estonia 102. hooaja uuslavastuste tutvustamisest 9. sept. Tallinnas Estonia maja taga ajaloolisel turuplatsil

  18. Europeanization in the "Other" Europe: Writing the Nation into "Europe" Education in Slovakia and Estonia

    Science.gov (United States)

    Michaels, Deborah L.; Stevick, E. Doyle

    2009-01-01

    How is the tension between renewed nationalist and European narratives of belonging being unfolded in the curricula, discourse, and practice of civic education in Slovakia and Estonia. As two post-socialist territories that were "reborn" as independent nation-states in the 1990s, Slovakia and Estonia were confronted with pressure to…

  19. the Danish cement industry

    OpenAIRE

    la Cour, Lisbeth Funding; Møllgård, Peter

    2001-01-01

    We test econometrically whether the sole Danish producer of cement holds a dominant position in the Danish market for (grey) cement. In import penetration tests, we find that its pricing and quantity decisions are independent of import price and quantity, implying that it can act to a considerable extent independently of its competitors. We also test whether it can act independently of its customers and find that its demand is inelastic with respect to its price. It thus holds a dominant posi...

  20. Valge Laeva hukk : Estonia katastroof meie peas = The wreck of the White ship : on the catastrophe of the Estonia / Anders Härm

    Index Scriptorium Estoniae

    Härm, Anders, 1977-

    2009-01-01

    "Estonia" katasroofist ja meedia osast selle kajastamisel, Juhan Leinbergist ja maltsvetlusest ning "valge laeva" kui priiuse laeva ja lootuse kujundist Eesti kultuuris ning selle tähendusest eestlaste teadvuses

  1. Vessel-Source Pollution and Coastal State Jurisdiction in the South-Eastern Baltic Sea : National Report of Estonia / Hannes Veinla

    Index Scriptorium Estoniae

    Veinla, Hannes, 1957-

    2006-01-01

    Laevadelt lähtuv merereostus ja kaldariigi jurisdiktsioon Balti mere kaguosas : Eesti. - Lisatud: Estonia : Economic Zone Act of Estonia : 28 January 1993 : Annex I, lk. 121-124 ; Estonia : State Borders Act of Estonia : 30 June 1994 : Annex II, lk. 125-138

  2. Master plan study - District heating Kohtla-Jaerve and Johvi municipalities. Estonia. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The main deficiencies of the district heating system in Kohtla-Jaerve, Ahtme and Johvi (Estonia) were identified as being: Inefficiency of the heat and power production plants; Lack of means for the consumers to control their consumption of energy due to the existing constant flow system; The environmental impact from heat and power production based on oil shale; Water and heat losses from the network; Low heat intensity in the Johvi area. Investigations indicate that improvement should have first priority at the Kohtla-Jaerve power plant, total investment is estimated at US D 60,3 million, of which US D 48 million are foreign costs. The cash flow will be negative in the first half of the projects lifetime. Estii Energia should be involved in the financing of the project. At the present price level, introduction of variable flow does not significantly improve the financial viability of the project, and the improvement of the district heating system might be carried out at a later stage, when the tariff has found a more stable level and the financial viability will be more significant. Implementation of new boilers in the Kohtla-Jaerve power plant. Circulating Fluidized Bed boilers, as well as electrostatic filters and estimated to reduce the environmental impact considerably. A more in depth study of the environmental impact from utilisation of oil shale should be carried out, also in order to inform possible investors of risk of investing in the oil shale industry. It will be more expensive to supply Johvi as an independent district heating system than if Johvi is supplied from Ahtme. The results arrived at are based on a range of the crucial assumptions that: the price of oil shale is expected to reach 75% of the price of coal, the sales price of electricity from plants is 62% of the consumer price, the exchange rate of the Estonian currency is kept constant to the DEM and that the inflation is Estonia will decline from 21% to 2,3% in 2005. (ARW)

  3. Eesti Gas, Estonia. Sales and marketing course

    International Nuclear Information System (INIS)

    1994-01-01

    A weekly sales and marketing course was organized by the Dansk Olie and Naturgas (the National Oil and Gas Company of Denmark) in Denmark for the Eesti Gas representatives. The program encompassed a survey of the Danish natural gas marketing, sales to the gas utilities and to industry, use of the natural gas in cogeneration plants and the gas pricing as an instrument of economic and environmental policy. Examples of negotiations with Danish industrial and municipal consumers were presented. Competitiveness of natural gas compared to other energy sources was discussed, taxation principles considered. (EG)

  4. Effects of land use on arbuscular mycorrhizal fungal communities in Estonia.

    Science.gov (United States)

    Sepp, Siim-Kaarel; Jairus, Teele; Vasar, Martti; Zobel, Martin; Öpik, Maarja

    2018-04-01

    Arbuscular mycorrhizal (AM) fungal communities vary across habitat types, as well as across different land use types. Most relevant research, however, has focused on agricultural or other severely human-impacted ecosystems. Here, we compared AM fungal communities across six habitat types: calcareous grassland, overgrown ungrazed calcareous grassland, wooded meadow, farmyard lawn, boreonemoral forest, and boreonemoral forest clear-cut, exhibiting contrasting modes of land use. AM fungi in the roots of a single host plant species, Prunella vulgaris, and in its rhizosphere soil were identified using 454-sequencing from a total of 103 samples from 12 sites in Estonia. Mean AM fungal taxon richness per sample did not differ among habitats. AM fungal community composition, however, was significantly different among habitat types. Both abandonment and land use intensification (clearcutting; trampling combined with frequent mowing) changed AM fungal community composition. The AM fungal communities in different habitat types were most similar in the roots of the single host plant species and most distinct in soil samples, suggesting a non-random pattern in host-fungal taxon interactions. The results show that AM fungal taxon composition is driven by habitat type and land use intensity, while the plant host may act as an additional filter between the available and realized AM fungal species pool.

  5. Underdog or bulldog: introducing biogas technologies in Estonia

    Energy Technology Data Exchange (ETDEWEB)

    Roose, Antti; Reinsoo, Kadri [University of Tartu, Department of Geography, Tartu (Estonia); Oja, Ahto [Monus Minek Ltd, Aeaesmaee (Estonia); Varzinskas, Visvaldas [Kaunas University of Technology, Institute of Environmental Engineering, Kaunas (Lithuania)

    2012-12-15

    The production and use of biogas, along with corresponding sector-specific activities and technologies, is a relatively new subject in Estonia. This paper gives an instructive overview of main barriers behind the development incentives, policy support and technological innovation in terms of emerging market for biogas. The article examines the complexity of market-related, political, technological and social obstacles for introduction biogas technologies. There is a major gap between resource potential, technological capacity and practice in Estonia. About 2 % of the theoretical potential of biogas is being used, totalling around 11 million Nm{sup 3}, based primarily on landfill biogas. First, political setting for biogas innovation is still vague, however, consolidated and enhanced since 2010 to compete with other renewables and mainstream energy technologies. The article underlines the statement that the reason why Estonian biogas production has not followed the path of growth and technology transfer is the low renewable electricity feed-in tariff. However, there are many other legal and engineering factors that have held back biogas applications and sector development in general. Stakeholders have established the Estonian Biogas Association, increasing sector's visibility, targeted lobby to support policy-making, technological and social innovation and professional networking. Though getting the biogas sector to succeed demands a comprehensive approach and involvement of more actors in demand side including local leaders and consumers, both enthusiasm and scepticism should be informed by a sound understanding of framework conditions and complexities for path-breaking transformations in energy systems. To promote biogas production, profitable and technologically feasible showcases should demonstrate benefits and issues to the target group and stakeholders. Instead agricultural and CHP development mode, the priority of using biogas in Estonia could be seen as

  6. Seasonality of alcohol-related phenomena in Estonia

    Science.gov (United States)

    Silm, Siiri; Ahas, Rein

    2005-03-01

    We studied alcohol consumption and its consequences as a seasonal phenomenon in Estonia and analysed the social and environmental factors that may cause its seasonal rhythm. There are two important questions when researching the seasonality of human activities: (1) whether it is caused by natural or social factors, and (2) whether the impact of the factors is direct or indirect. Often the seasonality of social phenomena is caused by social factors, but the triggering mechanisms are related to environmental factors like temperature, precipitation, and radiation via the circannual calendar. The indicators of alcohol consumption in the current paper are grouped as: (1) pre-consumption phenomena, i.e. production, tax and excise, sales (beer, wine and vodka are analysed separately), and (2) post-consumption phenomena, i.e. alcohol-related crime and traffic accidents and the number of people detained in lockups and admitted to alcohol treatment clinics. In addition, seasonal variability in the amount of alcohol advertising has been studied, and a survey has been carried out among 87 students of Tartu University. The analysis shows that different phenomena related to alcohol have a clear seasonal rhythm in Estonia. The peak period of phenomena related to beer is in the summer, from June to August and the low point is during the first months of the year. Beer consumption correlates well with air temperature. The consumption of vodka increases sharply at the end of the year and in June; the production of vodka does not have a significant correlation with negative temperatures. The consumption of wine increases during summer and in December. The consequences of alcohol consumption, expressed as the rate of traffic accidents or the frequency of medical treatment, also show seasonal variability. Seasonal variability of alcohol consumption in Estonia is influenced by natural factors (temperature, humidity, etc.) and by social factors (celebrations, vacations, etc.). However

  7. Effect of thallium in cement oven dusts on the growth and thallium uptake of several culture plants for the determination of thallium thresholds in plants and soils. Wirkung des Thallium in Zementofenstaeuben auf Wachstum und Thallium-Aufnahme mehrerer Kulturpflanzen zur Ermittlung von Thallium-Grenzwerten in Pflanzen und Boeden

    Energy Technology Data Exchange (ETDEWEB)

    Makridis, H

    1987-02-27

    After preliminary experiments in the methodology of Tl-analysis in plants and soils, phytotoxic Tl-concentrations and specific toxicity symptoms of different crops (beans, rape) have been determined in hydroponic culture with TlCl/sub 3/.H/sub 2/O. In pot experiments, critical Tl-levels were evaluated with regard to yield and Tl-uptake of plants on different soils, as a basis for the classification of soilcontamination by Tl originating form cement klink dust. The latter is a main source of Tl-emissions. Thus, several dusts with differing Tl-concentrations were tested in extensive two-year pot-experiments with different plants, and critical levels for lime- and potash- containing dusts have been elaborated. (orig./MG)

  8. Development and problems of radioactive waste management infrastructure in Estonia

    International Nuclear Information System (INIS)

    Putnik, H.; Realo, E.

    2001-01-01

    Estonia is one of a few countries where the establishment of radiation protection and radioactive waste management infrastructure started only recently, soon after regaining independence in the beginning of 1990's. Both legislative and regulatory infrastructure had to be built from scratch, in parallel with the beginning of urgent activities and practices to manage waste streams inherited from the past. Despite significant deficiency of local expertise and specialists in the field, the main objectives of the establishment were set up: to enforce national legislation basing on contemporary international principles, criteria, requirements and to implement structures and procedures for an efficient regulation of radiation safety issues, including practices involving radioactive waste management and decommissioning

  9. Historical survey of nuclear non-proliferation in Estonia

    International Nuclear Information System (INIS)

    Maalmann, I.

    2004-01-01

    The presentation gives an overview about the project initiated in co-operation between the Swedish Nuclear Power Inspectorate (SKI) and the Estonian Radiation Protection Centre (ERPC) to carry out a historical survey of the nuclear activities taken place in the territory of Estonia after the World War II. The main purpose of the project was to create transparency in the State's nuclear related past and to submit the results of the conducted historical survey as a volunteer supplement to the Additional Protocol declaration. (author)

  10. Closed nuclear facilities in Estonia: developments and problems

    International Nuclear Information System (INIS)

    Realo, E.; Realo, K.

    2000-01-01

    At present Estonia has no operating nuclear or a radioactive material production facility. As a legacy of the past the country has become responsible for the decommissioning of two large nuclear cycle facilities of the former USSR. Besides limited funding, major problems arise from deficiencies in legislation, expertise, training and research. International co-operation has been of immense importance to overcome the problems, to establish the national radiation protection and radioactive waste management infrastructure and to launch decommissioning and remediation activities. An overview is given on the status and problems. Copyright (2000) Australasian Radiation Protection Society Inc

  11. Estonia hukk jõuab kinolinale / Anari Koppel

    Index Scriptorium Estoniae

    Koppel, Anari

    2003-01-01

    Saksamaal esilinastub 2. oktoobril poliitiline põnevusfilm "Balti torm" ("Baltic Storm"), mis kujutab parvlaev "Estonia" hukku venelaste vandenõu tulemusena. Film jõuab Eestis linale novembri alul. Produtsendid on Jutta Rabe ja Kaj Holmberg, režissöör ja üks stsenariste Reuben Leder, peaosades Greta Scacchi ja Jürgen Prochnow. Kaasa teeb ka Donald Sutherland USA kindrali rollis. Eesti näitlejaist teevad kaasa Rein Oja ja väikeses rollis Urmas Alenderi lesk Helje Kaskel. Kõlab ka U. Alenderi laul

  12. Energy Efficiency Improvement Opportunities for the Cement Industry

    Energy Technology Data Exchange (ETDEWEB)

    Price, Lynn; Worrell, Ernst; Galitsky, Christina; Price, Lynn

    2008-01-31

    This report provides information on the energy savings, costs, and carbon dioxide emissions reductions associated with implementation of a number of technologies and measures applicable to the cement industry. The technologies and measures include both state-of-the-art measures that are currently in use in cement enterprises worldwide as well as advanced measures that are either only in limited use or are near commercialization. This report focuses mainly on retrofit measures using commercially available technologies, but many of these technologies are applicable for new plants as well. Where possible, for each technology or measure, costs and energy savings per tonne of cement produced are estimated and then carbon dioxide emissions reductions are calculated based on the fuels used at the process step to which the technology or measure is applied. The analysis of cement kiln energy-efficiency opportunities is divided into technologies and measures that are applicable to the different stages of production and various kiln types used in China: raw materials (and fuel) preparation; clinker making (applicable to all kilns, rotary kilns only, vertical shaft kilns only); and finish grinding; as well as plant wide measures and product and feedstock changes that will reduce energy consumption for clinker making. Table 1 lists all measures in this report by process to which they apply, including plant wide measures and product or feedstock changes. Tables 2 through 8 provide the following information for each technology: fuel and electricity savings per tonne of cement; annual operating and capital costs per tonne of cement or estimated payback period; and, carbon dioxide emissions reductions for each measure applied to the production of cement. This information was originally collected for a report on the U.S. cement industry (Worrell and Galitsky, 2004) and a report on opportunities for China's cement kilns (Price and Galitsky, in press). The information provided in

  13. CEMENT. "A Concrete Experience." A Curriculum Developed for the Cement Industry.

    Science.gov (United States)

    Taylor, Mary Lou

    This instructor's guide contains 11 lesson plans for inplant classes on workplace skills for employees in a cement plant. The 11 units cover the following topics: goals; interpreting memoranda; applying a standard set of work procedures; qualities of a safe worker; accident prevention; insurance forms; vocabulary development; inventory control…

  14. Effect of cement dust pollution on certain physical parameters of maize crop and soils

    Energy Technology Data Exchange (ETDEWEB)

    Parthasarathy, S; Arunachalam, N; Natarajan, K; Oblisami, G; Rangaswami, G

    1975-04-01

    A study was undertaken in the fields near a cement factory where the cement dust is the prime pollutant to the field crops and soils. Cement dust deposit varied with the distance from the kiln and fourth and fifth leaves of maize had comparatively more dust than the first three leaves from the top. The cement dust deposited plants showed a suppression in most of the characters like leaf size, number and size of cobs and plant height when compared to plants in non-polluted fields. On comparison with the physical characters of the soils from the control field the soil from cement dust polluted field showed a decrease in water holding capacity and pore space while thermal conductivity and specific heat were more. Artificial mixtures of red and black soils with cement dust showed similar trend as those of the field sample, the black soil being affected more seriously than the red soil.

  15. Cement for Oil Well Cementing Operations in Ghana

    African Journals Online (AJOL)

    Michael

    For Portland cement to qualify as oil well cement, the chemical and physical properties must meet ..... Reservoir Engineering, Stanford University,. Stanford, California, pp. ... Construction”, PhD Thesis, Kwame Nkrumah. University of Science ...

  16. Measurement and control of cement set times in waste solidification

    International Nuclear Information System (INIS)

    Stone, J.A.; d'Entremont, P.D.

    1976-09-01

    Fixation of radioactive waste in concrete was investigated on laboratory scale. Some cement formulations containing simulated or actual sludges from the Savannah River Plant had set times that would be too short for reliable handling in plant equipment. Set times could be controlled by use of excess water, but the concrete forms produced had inferior strength. A commercial organic retarder was found to be effective for increasing set times of cement-sludge formulations. However, the dosage of retarder required to control set times of high-alumina cement formulations was 1.0 to 1.5 wt percent of dry solids, which is 5 to 10 times the normal dosage for Portland cements. Data were obtained to predict the optimum content of retarder and water

  17. Dust extraction from gas in cement kilns, using bag filters; Depoussierage des gaz de four cimentier par les filtres a manches

    Energy Technology Data Exchange (ETDEWEB)

    Harmegnies, M. [CALCIA, 78 - Guerville (France). Direction Technique

    1996-12-31

    After a review of regulations concerning cement plant emissions, the two main cement production techniques (dry and semi-dry processes) are described and the electrostatic and bag filter de-dusting techniques are compared. Examples of pilot applications of these techniques in two French cement plants are presented and operating results (performances, transient procedures, costs) are discussed

  18. ULTRA-LIGHTWEIGHT CEMENT

    Energy Technology Data Exchange (ETDEWEB)

    Fred Sabins

    2001-10-23

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). Work reported herein addresses tasks performed in the fourth quarter as well as the other three quarters of the past year. The subjects that were covered in previous reports and that are also discussed in this report include: Analysis of field laboratory data of active cement applications from three oil-well service companies; Preliminary findings from a literature review focusing on problems associated with ultra-lightweight cements; Summary of pertinent information from Russian ultra-lightweight cement literature review; and Comparison of compressive strengths of ULHS systems using ultrasonic and crush methods Results reported from the fourth quarter include laboratory testing of ULHS systems along with other lightweight cement systems--foamed and sodium silicate slurries. These comparison studies were completed for two different densities (10.0 and 11.5 lb/gal) and three different field application scenarios. Additional testing included the mechanical properties of ULHS systems and other lightweight systems. Studies were also performed to examine the effect that circulation by centrifugal pump during mixing has on breakage of ULHS.

  19. Renewable Energy Policy Fact sheet - Estonia

    International Nuclear Information System (INIS)

    2017-09-01

    The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. Electricity from renewable sources is mainly promoted through feed-in premiums (FiP). In addition, investment subsidies are available for biogas/biomass-based RES-E and wind power installations. Renewable heat is stimulated through investment subsidies to CHP plants generating renewable heat and electricity, as well as subsidies for private heat consumers. Renewable transport fuels are currently mainly incentivised by way of a support scheme to promote the purchase of electric cars that use power produced from renewable energy sources. Recently, a measure for supporting bio-methane in the transport sector has been adopted. Generally, a number of investment subsidy schemes are in place to promote the development, installation and use of renewable energy production installations. However, certain subsidy conditions still have to be announced and implemented. The total amount of financial support to be allocated to renewable energy and energy efficiency related projects during period 2014-2020 will be over euro 490 million. The current administratively determined FiP scheme is set to be replaced by an auction-based scheme within short

  20. Do alcohol excise taxes affect traffic accidents? Evidence from Estonia.

    Science.gov (United States)

    Saar, Indrek

    2015-01-01

    This article examines the association between alcohol excise tax rates and alcohol-related traffic accidents in Estonia. Monthly time series of traffic accidents involving drunken motor vehicle drivers from 1998 through 2013 were regressed on real average alcohol excise tax rates while controlling for changes in economic conditions and the traffic environment. Specifically, regression models with autoregressive integrated moving average (ARIMA) errors were estimated in order to deal with serial correlation in residuals. Counterfactual models were also estimated in order to check the robustness of the results, using the level of non-alcohol-related traffic accidents as a dependent variable. A statistically significant (P traffic accidents was disclosed under alternative model specifications. For instance, the regression model with ARIMA (0, 1, 1)(0, 1, 1) errors revealed that a 1-unit increase in the tax rate is associated with a 1.6% decrease in the level of accidents per 100,000 population involving drunk motor vehicle drivers. No similar association was found in the cases of counterfactual models for non-alcohol-related traffic accidents. This article indicates that the level of alcohol-related traffic accidents in Estonia has been affected by changes in real average alcohol excise taxes during the period 1998-2013. Therefore, in addition to other measures, the use of alcohol taxation is warranted as a policy instrument in tackling alcohol-related traffic accidents.

  1. The social costs of alcohol misuse in Estonia.

    Science.gov (United States)

    Saar, Indrek

    2009-01-01

    The aim of this study was to estimate the social costs of alcohol misuse in Estonia in 2006. Using a prevalence-based cost-of-illness approach, both direct and indirect costs were considered, including tangible costs associated with health care, criminal justice, rescue services, damage to property, premature mortality, incarceration, incapability of working due to illnesses, and lower labor productivity. The results show that alcohol misuse cost Estonia more than EUR 200 million in 2006. The costs involved are estimated to represent 1.6% of the gross domestic product (GDP), which is relatively high in comparison with many other countries. In addition, the state receives less receipts from the alcohol excise tax than the costs that it incurs as a consequence of alcohol misuse, which points to the existence of economic inefficiency with respect to the alcohol market. The results of this study suggest that there is definitely a need for further cost-benefit analysis to reach a conclusion regarding the possible utility of government intervention. Copyright 2008 S. Karger AG, Basel.

  2. 137Cs in soil profiles in NE Estonia

    International Nuclear Information System (INIS)

    Lust, M.; Realo, K.; Realo, E.

    2002-01-01

    Radiocaesium contamination in soil was produced by two fallout's: a global fallout caused by nuclear weapons testing in the atmosphere (1950s to 1970s) and a regional one - during/after the Chernobyl accident (1986). The area] distribution of the 137 CS fallout after the 1986 accident was extremely uneven in Estonia. Our previous studies showed that about 60% of its total deposition with the countrywide mean of 2 kBq m -2 occurred predominantly in the north-eastern part of Estonia. In this region the maximum deposition approached the values of 40 kBq m -2 . This is the reason why soil profiles in this region have been of interest. We have also determined the 137 Cs activity concentrations as a function of soil depth during 1991-2000. Attempts have been made to model the found depth-distributions of radiocaesium concentration and to find the possible time-dependent behaviour of these distributions in soil. The migration of radiocaesium into soil is dependent on several factors: soil properties, vegetation, mode of deposition, etc. For this reason, averaged distribution parameters for both total and Chernobyl 137 Cs have been used for deriving general trends of the migration processes. (au)

  3. Design of accounting curriculum: The case of Estonia

    Directory of Open Access Journals (Sweden)

    Alver Lehte

    2014-01-01

    Full Text Available The process of globalization sets new requirements for the professional qualification of accountants and auditors. In the business world globalized investment market demands consistent high quality financial information across borders; investors are looking for a global accounting profession to provide it. There is more pressure on accounting professionals to expand and enhance their knowledge, skills, and abilities beyond what they are currently likely to possess. Providers of accounting education must take into account the changed world and create contemporary curricula. In Estonia the change from a command to a market economy has inevitably influenced not only the accounting framework but also the entire system of accounting education. It is clear that without a design of accounting curricula it is practically impossible to fulfill requirements of nowadays high quality financial information. Tallinn University of Technology (TUT holds on the advanced level of accounting education the leading position in Estonia. The accounting curriculum (on the graduate level as well as undergraduate level is the most popular among all curricula at the Tallinn School of Economics and Business Administration of TUT. It is a joint system, which consists of undergraduate and graduate degree programs. Small sub specializations: for example in financial accounting, managerial cost accounting, taxation and auditing become evident while interpreting the graduate and undergraduate programs as one united system. The paper explains a new model of accounting curriculum developed at TUT as well as its educational philosophy and principles of designing. It also describes conditions required for development and continuous improvement of competitive curriculum.

  4. Technology Roadmaps: Cement

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-07-01

    To support its roadmap work focusing on key technologies for emissions reductions, the International Energy Agency (IEA) also investigated one particular industry: cement. Cement production includes technologies that are both specific to this industry and those that are shared with other industries (e.g., grinding, fuel preparation, combustion, crushing, transport). An industry specific roadmap provides an effective mechanism to bring together several technology options. It outlines the potential for technological advancement for emissions reductions in one industry, as well as potential cross-industry collaboration.

  5. Reducing cement's CO2 footprint

    Science.gov (United States)

    van Oss, Hendrik G.

    2011-01-01

    The manufacturing process for Portland cement causes high levels of greenhouse gas emissions. However, environmental impacts can be reduced by using more energy-efficient kilns and replacing fossil energy with alternative fuels. Although carbon capture and new cements with less CO2 emission are still in the experimental phase, all these innovations can help develop a cleaner cement industry.

  6. Cement Mason's Curriculum. Instructional Units.

    Science.gov (United States)

    Hendirx, Laborn J.; Patton, Bob

    To assist cement mason instructors in providing comprehensive instruction to their students, this curriculum guide treats both the skills and information necessary for cement masons in commercial and industrial construction. Ten sections are included, as follow: related information, covering orientation, safety, the history of cement, and applying…

  7. Cementation of liquid radioactive waste

    International Nuclear Information System (INIS)

    Efremenkov, V.

    2004-01-01

    The cementation methods for immobilisation of radioactive wastes are discussed in terms of methodology, chemistry and properties of the different types of cements as well as the worldwide experience in this field. Two facilities for cementation - DEWA and MOWA - are described in details

  8. Cementing a wellbore using cementing material encapsulated in a shell

    Energy Technology Data Exchange (ETDEWEB)

    Aines, Roger D.; Bourcier, William L.; Duoss, Eric B.; Spadaccini, Christopher M.; Cowan, Kenneth Michael

    2016-08-16

    A system for cementing a wellbore penetrating an earth formation into which a pipe extends. A cement material is positioned in the space between the wellbore and the pipe by circulated capsules containing the cement material through the pipe into the space between the wellbore and the pipe. The capsules contain the cementing material encapsulated in a shell. The capsules are added to a fluid and the fluid with capsules is circulated through the pipe into the space between the wellbore and the pipe. The shell is breached once the capsules contain the cementing material are in position in the space between the wellbore and the pipe.

  9. Cementing a wellbore using cementing material encapsulated in a shell

    Energy Technology Data Exchange (ETDEWEB)

    Aines, Roger D.; Bourcier, William L.; Duoss, Eric B.; Floyd, III, William C.; Spadaccini, Christopher M.; Vericella, John J.; Cowan, Kenneth Michael

    2017-03-14

    A system for cementing a wellbore penetrating an earth formation into which a pipe extends. A cement material is positioned in the space between the wellbore and the pipe by circulated capsules containing the cement material through the pipe into the space between the wellbore and the pipe. The capsules contain the cementing material encapsulated in a shell. The capsules are added to a fluid and the fluid with capsules is circulated through the pipe into the space between the wellbore and the pipe. The shell is breached once the capsules contain the cementing material are in position in the space between the wellbore and the pipe.

  10. The mechanical effect of the existing cement mantle on the in-cement femoral revision.

    LENUS (Irish Health Repository)

    Keeling, Parnell

    2012-08-01

    Cement-in-cement revision hip arthroplasty is an increasingly popular technique to replace a loose femoral stem which retains much of the original cement mantle. However, some concern exists regarding the retention of the existing fatigued and aged cement in such cement-in-cement revisions. This study investigates whether leaving an existing fatigued and aged cement mantle degrades the mechanical performance of a cement-in-cement revision construct.

  11. Saaremaa lad brings FBI conference to Estonia / Kalle Laanet ; interv. Rein Sikk

    Index Scriptorium Estoniae

    Laanet, Kalle, 1965-

    2007-01-01

    Riigikogu liige vastab küsimustele, mis puudutavad tema õpinguid FBI akadeemias, Tallinnas toimuvat FBI konverentsi ning Eesti sisejulgeolekut. Lisa: Estonian Police statistics; Registered crimes in Estonia; From police officer to minister; What happened in April?

  12. Estonia - üks tõeline eestimaine spaa / Dagmar Reinolt

    Index Scriptorium Estoniae

    Reinolt, Dagmar

    2015-01-01

    Heaoluspaa võtmes renoveeritud Estonia Spa Hotelsi ühest kompleksist. Rekonstrueerimisprojekti arhitektid: Raivo Kotov, Indrek Mikk. Rekonstrueerimisprojekti sisearhitektid: Raili Paling, Liis Lindvere, Kadri Kaldam, Kärt Loopalu. Valmimisaasta: 2015

  13. Reasons for internal migration in Estonia 1989-2000 / Mare Ainsaar

    Index Scriptorium Estoniae

    Ainsaar, Mare

    2004-01-01

    Autor tutvustab oma uurimust "Reasons for move: a study on trends and reasons of internal migration with particular interest in Estonia 1989-2000" (Turku University, 2004) Eesti elanikkonna migratsioonist ja selle põhjustest. Skeemid

  14. Estonia juhti kahtlustatakse ettevõtte varade omastamises / Ester Vilgats, Eno-Gerrit Link, Teet Roosaar

    Index Scriptorium Estoniae

    Vilgats, Ester

    2008-01-01

    Endine Pärnu linnapea, taastusravikeskuse Estonia pikaaegne juht Vello Järvesalu peeti kinni kahtlustatuna ettevõtte varade omastamises suures ulatuses. Kommenteerivad: Mart Viisitamm, Jane Mets ja Ahti Kõo

  15. Master plan study - District heating Sillamaee municipality. Estonia. Final report. Appendices for chapter 9

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The appendices to the final report on the master plan study on district heating in the municipality in Estonia, chapter nine, gives data related to general economic assumptions for financial and economic calculations, fuel consumption, financing, prices, fuel consumption. (ARW)

  16. Hip-hop ja ooper kohtuvad Estonias / Marko Lillemägi

    Index Scriptorium Estoniae

    Lillemägi, Marko

    2006-01-01

    10. juunil Rahvusooperis Estonia etenduvast Mozarti ooperi "Cosi fan tutte" tänapäevasest versioonist, mis valmis Inglismaa Glyndebounre'i festivali, Saksamaa komische operi ja Soome Rahvusooperi koostöös, lavastaja Clare Whistler

  17. Cement encapsulation of low-level radioactive slurries of complex chemistry

    International Nuclear Information System (INIS)

    Cau Dit Coumes, C.

    2000-01-01

    Investigations have been carried out to solidify in cement a low-level radioactive waste of complex chemistry which should be produced in a new plant designed to process radioactive effluents from CEA Cadarache Research Center. Direct cementation comes up against a major problem: a very long setting time of cement due to strong inhibition by borates from the waste. A two-stage process, including a chemical treatment prior to immobilization, has been elaborated and the resulted material characterized. (authors)

  18. Study of mechanical and physicochemical properties of cementated spent ion-exchange-resins

    International Nuclear Information System (INIS)

    Patek, P.

    1981-09-01

    As first part of a study on the possibilities, to immobilize spent ion exchange resins, for final disposal, the dependence of compressive strength from the composition of cement - resin mixtures was detected. Powdered resins, bead resins and ashes from the incinerator plant and several cement brands were examinated. As result an area was defined in the three-phase diagram of cement, resins and water, in which the following leach tests will be performed. (author)

  19. Cement-based processes for the immobilization of intermediate level radioactive waste

    International Nuclear Information System (INIS)

    Brown, D.J.; Lee, D.J.; Price, M.S.T.; Smith, D.L.G.

    1985-01-01

    Increasing attention is being paid to the use of cement-based materials for the immobilisation of intermediate level wastes. Various cementitious materials are surveyed and the use of blast furnace slag is shown to be advantageous. The properties of cemented wastes are surveyed both during processing and as solid products. The application of Winfrith Cementation Laboratory technology to plant and flowsheet development for Winfrith Reactor sludge immobilisation is described. (author)

  20. Residual Cadmium and Lead Pollution at a Former Soviet Military Airfield in Tartu, Estonia

    International Nuclear Information System (INIS)

    Mander, Ulo; Kull, Ain; Frey, Jane

    2004-01-01

    This paper presents data on the levels and dynamics of cadmium (Cd) and lead (Pb) concentration in the plants, soil, and groundwater of the landing corridor and airfield of a former Soviet military air base in Estonia, immediately at the end of its 40-year service in 1992 and over the following 8 yr. In 1991-92 we found high Cd concentrations in the meadow plants Trifolium pratense and Dactylis glomerata (up to 56 mg kg -1 ). In 1993, the Cd concentration had dropped to 0.12-0.19 mg kg -1 , and stabilized in 1997-2000 at 0.04 mg kg -1 . Cd concentration in plants decreased significantly with increasing distance from the landing strip. Elevated Cd concentration (0.012 mg L -1 ) was found in the fuel of the TU-22M (Backfire) strategic bombers. In 1991 and 1993, leaded fuel influenced the mean Pb concentration in plants (1.8-4.2 mg kg -1 ). Average Pb concentration in both topsoil and the 30-40 cm soil horizon decreased between 1991 and 2000 from 28 to 6.5 and from 13.5 to 4.3 mg kg -1 , respectively. Cd concentration in the topsoil of the landing corridor showed a significant increase between 1991 and 1993 (0.07-0.3 and 0.3-1.2 mg kg -1 , respectively), but stabilized later on the level of 0.04 mg kg -1 . The concentrations of both Pb and Cd in the soil were higher closer to the fuel bunkers. Current assessment of the movement of these metals from the vegetation to the soil and to groundwater is linked to potential leaching to the surrounding environment

  1. Estonia ballett üle seitsme aasta taas Pärnus / Silja Joon

    Index Scriptorium Estoniae

    Joon, Silja, 1966-

    2010-01-01

    Rahvusooperi Estonia balleti kunstiline juht Toomas Edur Estonia balletitrupist ja 20. veebruaril toimuvast kolmest lühiballetist koosnevast balletiõhtust Pärnu kontserdimajas. Esitatakse Bohuslav Martinu "Enne öö saabumist" (koreograaf Nils Christe), Arnold Schönbergi "Pelléas ja Mélisande" (koreograaf Tiit Härm), Robert Schumanni "Teine sümfoonia" (koreograaf Uwe Scholz)

  2. Japanese tourists in Finland, Estonia and Latvia – a literature review

    OpenAIRE

    Suvanto, Hannele; Sudakova, Lea; Kattai, Kaili; Grīnberga-Zālīte, Gunta; Bulderberga, Zane

    2017-01-01

    Based on the results of this literature survey, it can be concluded that the following points are especially interesting from the perspective of rural tourism in Finland, Estonia and Latvia. Characteristics of Japanese tourists Most spend a lot of money but have a short time to spend it. Men have especially short holidays, staying around three nights. The location of Finland is crucial (airport in Helsinki and stopovers) and proximity to Estonia and Latvia convenient. Travel is mainly...

  3. Attitudes of Major Soviet Nationalities. Volume II. The Baltics. Estonia, Latvia, Lithuania.

    Science.gov (United States)

    1973-06-01

    acquired wide popularity (and probably snob appeal ). Kafka, Ionesco and Dostoyevsky were available to Soviet Estonians earlier than to the Russian reading...Estonia . chided as snob appeal ). Of Estonia’s 757 general schools, 556 (i.e. 71) use Estonian, 90 use Russian and 60 are mixed. 2 The same applies to...novels whicr combine literary quality with national appeal ro 2 ’), collective farm realism at its best (M. Traatl), realisti> lezcription of city life

  4. Uninvited guests: traditional insect repellents in Estonia used against the clothes moth Tineola bisselliella, human flea Pulex irritons and bedbug Cimex lectularius.

    Science.gov (United States)

    Sõukand, Renata; Kalle, Raivo; Svanberg, Ingvar

    2010-01-01

    Extensive folklore records from pre-modern Estonia give us an excellent opportunity to study a variety of local plant knowledge and plant use among the peasantry in various parts of the country. One important biocultural domain where plant knowledge has been crucial was in the various methods of combating different ectoparasites that cohabited and coexisted with humans and their domestic animals. Some of these methods were widely known (world-wide, Eurasia, Europe, Baltic Rim), while others were more local. Here we discuss ways of reducing clothes moths Tineola bisselliella (Hummel) (Lepidoptera: Tineidae), human fleas Pulex irritons L. (Siphonaptera: Pulicidae) and bedbugs Cimex lectularius L. (Hemiptera: Cimicidae) with the help of plants. Various taxa used as traditional repellents have been identified. The use of plants as repellents and their toxic principles are also discussed from a comparative perspective.

  5. The status of energy conservation in Taiwan's cement industry

    International Nuclear Information System (INIS)

    Su, Te-Li; Chan, David Yih-Liang; Hung, Ching-Yuan; Hong, Gui-Bing

    2013-01-01

    The cement industry represents one of the most energy intensive sectors in Taiwan. Energy audits are the direct tools which are employed to help reduce energy consumption. The objectives of energy audits are to establish energy audit systems, provide on-site energy audit service and reduce production cost. This study summarized the energy savings implemented in Taiwan's cement industry; the data were obtained from the on-line Energy Declaration System in 2010. The total implemented energy savings amounted to 68,512 kilo liter of crude oil equivalent (KLOE). The energy audit group audited seven Taiwanese cement plants in 2011 and revealed an energy saving potential of 2571.6 MWh of electricity and 1002.8 KLOE of thermal energy. The total potential energy saving was 1708.5 KL of crude oil equivalent (KLOE), equivalent to a 4560 t reduction in CO 2 emissions, representing the annual CO 2 absorption capacity of a 122 ha forest plantation. - Highlights: • This study summarizes the energy savings implemented in Taiwan's cement industry from the on-line Energy Declaration System. • The energy audit group audited seven Taiwanese cement plants in 2011 and revealed energy saving potential was 1708.5 KLOE. • This work aims to examine what Taiwan has done and also describes the current status in cement industry. • In addition, some potential energy conservation opportunities or measures are revealed in this paper

  6. Radiological accidents/incidents with caesium-137 in Estonia

    International Nuclear Information System (INIS)

    Sinisoo, M.

    1998-01-01

    A report is provided of an accident and an incident involving radioactive sources in Estonia. In the 1994 occurrence, looters of a depository of radioactive waste manipulated a source containing 137 Cs and received dangerous doses of radiation. One of the persons involved died, others suffered minor burns. Another event, which occurred in early 1995, did not have a tragic outcome: an abandoned 137 Cs source was found in the vicinity of the highway linking Tallinn and Narva and was disposed of safely. Both these accidents draw attention to the potential dangers caused by the insufficient survey of the territory, radiation protection structures not yet fully operable, and the lack of equipment and know-how. The lessons to be drawn from these events are considered on the basis of the chronologies and factual data. The report contains concise descriptions of the accidents, a medical overview of the fate of the injured persons and the lessons learned from these accidents. (author)

  7. "Estonia" müsteerium / Jüri Liim

    Index Scriptorium Estoniae

    Liim, Jüri

    2001-01-01

    Järgneb 26. okt., 2.,9.,16.,23.,30. nov., 7.,14. dets. ; 2002, 4.,11.,18.,25. jaan., 1.,8.,15.,22. veebr., 1.,8.,15.,22. märts, 5.,12.,26. aprill, 3.,10.,17.,24.,31. mai, 7.,14.,28. juuni, 5.,12.,19.,26. juuli, 2.,9.,16.,23. aug., 6.,13.,20.,27. sept., 4.,11.,25. okt., 1.,8.,15.,22.,29. nov., 13.,20. dets. ; 10.,17.,24., 31. jaan., 2003, 14. veebr., 7.,28. märts, 4.,11.,25. apr., 16.,23. mai, 6.,27. juuni, 11.,18. juuli. Reisilaev "Estonia" mõistatuslikust hukust

  8. On eco-efficiency and sustainable development in Estonia

    International Nuclear Information System (INIS)

    Randla, T.; Kurissoo, T.; Vilu, R.

    2002-01-01

    The basic idea of sustainable development is a firm understanding that all resources, renewable as well as non-renewable, are limited. Human activities should not exceed the buffering capacity of the earth's ecosystems and the replenishment potential of material cycles. Use of non-renewable, mainly mineral, resources should be kept at the minimum possible level, postponing the depletion of resources as far as possible. Concepts of environmental space and dematerialisation lie at the foundation of the practical launching of sustainable development. Analysis of regional sustainability and ecological efficiency of energy production, the balance of CO 2 , water, etc. were analysed for Estonia and Ida-Virumaa, north-eastern region of the country. The analysis carried out should be considered as a first step in the development and implementation of a national 'green' accounting system and environmental tax system based on the concept of environmental space. (author)

  9. HUMAN RESOURCE MANAGEMENT AND KNOWLEDGE ORGANIZATION IN ESTONIA AND SLOVENIA

    Directory of Open Access Journals (Sweden)

    Dana Mesner Andolšek

    2015-01-01

    Full Text Available The purpose of the analysis is to make a comparison of HRM practices among New Member States (especially Estonia and Slovenia and how these practices help to create the conditions to develop a knowledge organization. In the paper, the systemic and logical analysis of knowledge management concept and its relations with HRM was used. For empirical research a simple exploratory analysis statistical technique was used on Cranet (the Cranfield Network on Comparative Human Resource Management data on HRM practices across countries was used. Major findings allow stating that two important prerequisites for knowledge organization are met and they are successfully implemented through HRM practices especially in organizations in one country. The empirical research findings showed the trends in global economy and the ability of organizations in the New Member States to adapt through institutionally developed HRM practices.

  10. Acoustic monitoring techniques for corrosion degradation in cemented waste canisters

    International Nuclear Information System (INIS)

    Naish, C.C.; Buttle, D.; Wallace-Sims, R.; O'Brien, T.M.

    1991-01-01

    This report describes work carried out to investigate acoustic emission as a monitor of corrosion and degradation of wasteforms where the waste is potentially reactive metal. Electronic monitoring equipment has been designed, built and tested to allow long-term monitoring of a number of waste packages simultaneously. Acoustic monitoring experiments were made on a range of 1 litre cemented Magnox and aluminium samples cast into canisters comparing the acoustic events with hydrogen gas evolution rates and electrochemical corrosion rates. The attenuation of the acoustic signals by the cement grout under a range of conditions has been studied to determine the volume of wasteform that can be satisfactorily monitored by one transducer. The final phase of the programme monitored the acoustic events from full size (200 litre) cemented, inactive, simulated aluminium swarf wastepackages prepared at the AEA waste cementation plant at Winfrith. (Author)

  11. Damage identification in cement paste amended with carbon nanotubes

    Science.gov (United States)

    Soltangharaei, Vafa; Anay, Rafal; Assi, Lateef; Ziehl, Paul; Matta, Fabio

    2018-04-01

    Cement-based composites have been used as reliable materials in building and civil engineering infrastructure for many decades. Although there are several advantages, some drawbacks such as premature cracking may be problematic for sensitive applications such as those found in nuclear power plants or associated waste storage facilities. In this study, acoustic emission monitoring was employed to detect stress waves associated with damage progression during uniaxial compressive loading. Acoustic emission data resulting from loading of plain cement paste prisms and cement paste prisms amended with carbon nanotubes are compared. Unsupervised pattern recognition is employed to categorize the data. Results indicate that increased acoustic emission activity was recorded for the plain cement paste prisms when compared to prisms amended with carbon nanotubes.

  12. Evaluation of brazilian bentonites as additive in the radwaste cementation

    International Nuclear Information System (INIS)

    Tello, C.C.O. de.

    1988-01-01

    The behavior of some Brazilian bentonites has been evaluated, concerning to their use as additive in the radwaste cementation. The purpose of the bentonite is to retain the radioelements in the final product in leaching process. Experiments to determine properties such as compressive strenght, viscosity, set time leaching and cesium sorption have been carried out to this evaluation. After one-year test, the results show that the bentonites greatly reduce the cesium release. A literature survey about cementation process and plants and about the cement product characteristics has been made in order to obtain a reliable final product, able to be transported and storaged. Some leaching test methods and mathematical models, that could be applied in the evaluation of cement products with bentonite have been evaluated. (author) [pt

  13. Retrospective Analysis of Lophodermium seditiosum Epidemics in Estonia

    Directory of Open Access Journals (Sweden)

    HANSO, MÄRT

    2007-01-01

    Full Text Available The needle trace method (NTM, created and developed by the Finnish forest pathologists prof. T. Kurkela, dr. R. Jalkanen and T. Aalto during the last decade of the XX century, has been already used by several researchers of different countries for retrospective analysis of needle diseases (Hypodermella sulcigena, by R. Jalkanen et al. in Finland or herbivorous insect pests of Scots pine (Diprion pini, by T. Kurkela et al. in Finland; Bupalus piniaria, by H. Armour et al. in Scotland, but as well of pests of Sitka spruce (Gilpinia hercyniae, by D.T. Williams et al. in England. Scots pine in forest nurseries and young plantations of Estonia is often but irregularly suffering from the epidemics of the needle cast fungus Lophodermium seditiosum. Current environmental regulations exclude from the regulatory (control measures all the others except of well-argued prophylactic systems, built up on reliable prognoses. The last is inconceivable without the availability of a reliable, as well, and long-lasting retrospective time-series of L. seditiosum epidemics, which, as it is known from the last half of the XX century, are occupying large forest areas, usually not least than a half of (the small Estonia. An appropriate time-series would be useful, as well, for the more basic understanding of the accelerated mortality processes during the stand formation in early pole-age Scots pine plantations. Methodological principles of the use of NTM in an appropriate investigation together with the preliminary results of our research work, looking back for more than a century, are introduced and discussed in this investigation.

  14. Technological, economic and financial prospects of carbon dioxide capture in the cement industry

    International Nuclear Information System (INIS)

    Li, Jia; Tharakan, Pradeep; Macdonald, Douglas; Liang, Xi

    2013-01-01

    Cement is the second largest anthropogenic emission source, contributing approximately 7% of global CO 2 emissions. Carbon dioxide capture and storage (CCS) technology is considered by the International Energy Agency (IEA) as an essential technology capable of reducing CO 2 emissions in the cement sector by 56% by 2050. The study compares CO 2 capture technologies for the cement manufacturing process and analyses the economic and financial issues in deploying CO 2 capture in the cement industry. Post-combustion capture with chemical absorption is regarded as a proven technology to capture CO 2 from the calcination process. Oxyfuel is less mature but Oxyfuel partial capture—which only recycles O 2 /CO 2 gas in the precalciner—is estimated to be more economic than post-combustion capture. Carbonate looping technologies are not yet commercial, but they have theoretical advantages in terms of energy consumption. In contrast with coal-fired power plants, CO 2 capture in the cement industry benefits from a higher concentration of CO 2 in the flue gas, but the benefit is offset by higher SO x and NO x levels and the smaller scale of emissions from each plant. Concerning the prospects for financing cement plant CO 2 capture, large cement manufacturers on average have a higher ROE (return on equity) and lower debt ratio, thus a higher discount rate should be considered for the cost analysis than in power plants. IEA estimates that the incremental cost for deploying CCS to decarbonise the global cement sector is in the range US$350–840 billion. The cost estimates for deploying state-of-the art post-combustion CO 2 capture technologies in cement plants are above $60 to avoid each tonne of CO 2 emissions. However, the expectation is that the current market can only provide a minority of financial support for CO 2 capture in cement plants. Public financial support and/or CO 2 utilisation will be essential to trigger large-scale CCS demonstration projects in the cement

  15. Mineral resource of the month: hydraulic cement

    Science.gov (United States)

    van Oss, Hendrik G.

    2012-01-01

    Hydraulic cements are the binders in concrete and most mortars and stuccos. Concrete, particularly the reinforced variety, is the most versatile of all construction materials, and most of the hydraulic cement produced worldwide is portland cement or similar cements that have portland cement as a basis, such as blended cements and masonry cements. Cement typically makes up less than 15 percent of the concrete mix; most of the rest is aggregates. Not counting the weight of reinforcing media, 1 ton of cement will typically yield about 8 tons of concrete.

  16. Long-term studies on the leachability of cemented and non-cemented iodine-129 loaded sorption material

    International Nuclear Information System (INIS)

    Kaempffer, R.; Furrer, J.

    1989-01-01

    Leaching tests on the load AC 6120 iodine sorption material (12 wt.% Ag) in water and salt brines were performed over a rather long period of time to allow better judgement of the behavior of radioactive waste disposed of in a salt dome. The utilization of capacity of the loaded iodine sorption material from the Karlsruhe reprocessing plant (WAK) was 95% related to the amount of silver added. The result of the stationary leaching tests has been a leaching rate of the material not embedded in cement of < 0.1%, whereas the leaching rate of the iodine sorption material embedded in cement has been < 0.01% of the total iodine-129 inventory. After addition of carbon steel to the sorption material embedded in cement the same leaching rates were measured as for material not embedded in cement. The addition of stainless steel exerted but little influence on the leaching rate. (orig.)

  17. Cement-latex grouting mortar for cementing boreholes

    Energy Technology Data Exchange (ETDEWEB)

    Kateev, I S; Golyshkina, L A; Gorbunova, I V; Kurochkin, B M; Vakula, Ya V

    1980-01-01

    The need for the development of cement-latex grouting mortar for the purpose of separating strata when reinforcing boreholes at deposits in the Tatar Associated SSR is evaluated. Results of studies of the physical and mechanical properties of cement-latex grouting mortar systems (mortar plus brick) are presented. Formulas for preparing cement-latex grouting mortor are evaluated and results of industrial tests of such mortars shown.

  18. US cement industry

    Energy Technology Data Exchange (ETDEWEB)

    Nisbet, M.A.

    1997-12-31

    This paper describes the cement and concrete industry, and provides data on energy use and carbon dioxide emissions. The potential impact of an energy tax on the industry is briefly assessed. Opportunities identified for reducing carbon dioxide emissions include improved energy efficiency, alternative fuels, and alternative materials. The key factor in determining CO{sub 2} emissions is the level of domestic production. The projected improvement in energy efficiency and the relatively slow growth in domestic shipments indicate that CO{sub 2} emissions in 2000 should be about 5% above the 1990 target. However, due to the cyclical nature of cement demand, emissions will probably be above target levels during peak demand and below target levels during demand troughs. 7 figs., 2 tabs.

  19. Chemical environment in cements

    International Nuclear Information System (INIS)

    Glasser, F.B.; Angus, M.J.; McCulloch, C.E.; Macphee, D.; Rahman, A.A.

    1984-01-01

    The alkalinity of Portland cements is responsible for precipitation and low solubility of many radwastes species. The sources of alkalinity are evaluated and two chemical models, based on experimental and theoretical data presented enabling the effect of blending agents (PFA, silica fume, etc.) to be evaluated and the alkalinity of the system at longer ages predicted. The data take the form of a solubility model which is applicable to non-heat generating wastes. 7 refs., 10 figs

  20. Performance of Cement Containing Laterite as Supplementary Cementing Material

    Directory of Open Access Journals (Sweden)

    Abbas Bukhari, Z. S.

    2013-03-01

    Full Text Available The utilization of different industrial waste, by-products or other materials such as ground granulated blast furnace slag, silica fume, fly ash, limestone, and kiln dust, etc. as supplemen- tary cementing materials has received considerable attention in recent years. A study has been conducted to look into the performance of laterite as Supplementary Cementing Materials (SCM. The study focuses on compressive strength performance of blended cement containing different percentage of laterite. The cement is replaced accordingly with percentage of 2 %, 5 %, 7 % and 10 % by weight. In addition, the effect of use of three chemically different laterites have been studied on physical performance of cement as in setting time, Le-Chatlier expansion, loss on ignition, insoluble residue, free lime and specifically compressive strength of cement cubes tested at the age of 3, 7, and 28 days. The results show that the strength of cement blended with laterite as SCM is enhanced. Key words: Portland cement, supplementary cementing materials (SCM, laterite, compressive strength KUI – 6/2013 Received January 4, 2012 Accepted February 11, 2013

  1. Barium aluminate cement: its application

    International Nuclear Information System (INIS)

    Drozdz, M.; Wolek, W.

    1975-01-01

    The technology of manufacturing barium aluminate cement from barium sulfate and alumina, using a rotary kiln for firing the clinker is described. The method of granulation of the homogenized charge was used. Conditions of using the ''to mud'' method in industry were indicated. The physical and chemical properties of barium aluminate cement are determined and the quality of several batches of cement prepared on a semi-industrial scale and their suitability for making highly refractory concretes are tested. The optimal composition of the concretes is determined as a function of the mixing water and barium aluminate cement contents. Several experimental batches of concretes were used in the linings of furnaces in the steel industry. The suitability of these cements for use in fields other than steelmaking is examined. It is established that calcium aluminate cement has certain limited applications [fr

  2. Analysis of the cement clinker produced with incorporation of petroleum sludge

    Science.gov (United States)

    Benlamoudi, A.; Kadir, A. Abdul; Khodja, M.; Nuruddin, M. F.

    2018-04-01

    Very limited researches have been conducted on the incorporation of petroleum sludge waste into cement clinker production even though this waste may contain similar components to those of clinker raw materials. In this research, petroleum sludge was integrated into cement plant as raw material to produce the cement clinker. As results, incorporation of 5% of this waste was able to produce an acceptable quality of cement. Despite the use of petroleum sludge has decreased the properties of the produced clinker, but it still fit the requirements.

  3. Stability of reinforced cemented backfills

    International Nuclear Information System (INIS)

    Mitchell, R.J.; Stone, D.M.

    1987-01-01

    Mining with backfill has been the subject of several international meetings in recent years and a considerable research effort is being applied to improve both mining economics and ore recovery by using backfill for ground support. Classified mill tailings sands are the most commonly used backfill material but these fine sands must be stabilized before full ore pillar recovery can be achieved. Normal portland cement is generally used for stabilization but the high cost of cement prohibits high cement usage. This paper considers the use of reinforcements in cemented fill to reduce the cement usage. It is concluded that strong cemented layers at typical spacings of about 3 meters in a low cement content bulk fill can reinforce the fill and reduce the overall cement usage. Fibre reinforcements introduced into strong layers or into bulk fills are also known to be effective in reducing cement usage. Some development work is needed to produce the ideal type of anchored fibre in order to realize economic gains from fibre-reinforced fills

  4. Exergy-economic analysis of the baking workshop of the 'Sotacib' cement plant; Analyse exergeco-economique de l'atelier de cuisson de la cimenterie ''SOTACIB''

    Energy Technology Data Exchange (ETDEWEB)

    Gharsalli, A.; Hajji, N.; Gaabab, A.; Jeday, M.R. [ENIG, Gabes (Tunisia); Barkati, M. [SOTACIB, (Tunisia)

    2001-07-01

    The aim of this work is the elaboration of a calculation tool for the exergy analysis of a baking workshop belonging to the Tunisian-Algerian company of white cement (Sotacib). This workshop represents 30 to 60% of the cement production costs. The tool aims at calculating the exchanges of mass and energy and at evaluating the exergy losses and efficiencies of the main operations of transformation. (J.S.)

  5. Challenges of the growing African cement market – environmental issues, regulative framework, and quality infrastructure requirements

    Directory of Open Access Journals (Sweden)

    Schmidt Wolfram

    2018-01-01

    Full Text Available The African cement, concrete and construction business is growing at rapid pace. The cement sales are expected to grow rapidly until 2050. The number of newly built cement plants increases dramatically and in addition more cements are being imported from outside the continent, e.g. from Turkey, Pakistan, Indonesia, and China, driven by overcapacities in the countries of origin. This causes a high number of potentials and challenges at the same time. Newly built cement plants can operate directly at best technological state of the art and thus incorporate more sustainable technologies as well as produce new and more sustainable products such as cements blended with sustainable supplementary cementitious materials such as calcined clays, and industrial or agricultural by products. At the same time the new variety of binding agent as well as the international imports, which are driven by price considerations, make the cement market prone to quality scatter. This puts pressure on the quality control regulations and institutions to ensure safety of construction, healthy application, and environmental safety for the population. The paper presents possible solutions to build up the rapidly increasing African cement production more sustainably than in the rest of the world as well as the related challenges and obstacles that need to be overcome. Based on experiences with a series of pan-African cement testing laboratory proficiency schemes conclusions are made on technical, regulative and political level.

  6. Parteilisest tsensuurist Nõukogude Eestis. Party Censorship in Soviet Estonia

    Directory of Open Access Journals (Sweden)

    Tiiu Kreegipuu

    2012-04-01

    Full Text Available During the years of imposed Soviet rule in Estonia from 1940 to its collapse in 1991, Estonian culture and the written word were subject to Soviet censorship which due to its perseverance, extent and rigidity constrained creativity and self-expression. At the same time, archival documents and memories testify that considerable shifting could take place within this censorship which on the surface appeared strict and regulated, depending on the general ideological stance and the officials and party functionaries in place at the time. Soviet censorship is usually studied and described with the activities of the censorship office Glavlit as the focal point. However, for a more complete overview, it would be wise to keep in mind that a whole row of other institutions and authorities with the Communist Party in front also were involved in censorship matters. When it came to censorship, it was the party that had the final word – as it did with everything else – and if needed, it also acted as punisher. Apart from the role of censor, the Communist Party, its departments (with the Department for Propaganda and Agitation or Ideology in front and its officials also took part in hands-on censorship work, both in terms of decision-making and in dealing with concrete incidents (breach of censorship rules and censor mistakes but also in the search for and pointing out of ideological flaws. One area in which the party’s censorship activities manifested itself in a rather vivid manner was the leadership and control of the Soviet press. When analysing materials from the bureau of the Communist Party of Estonia’s Central Committee, it becomes clear that the party’s governing organs were constantly active in this area. The manifestation of problems and discussion of flaws here point to the circumstance that journalists and editors did not accept the censorship rules, but rather tried to find possibilities and means through which to modify or ignore them

  7. Guidebook for Using the Tool BEST Cement: Benchmarking and Energy Savings Tool for the Cement Industry

    Energy Technology Data Exchange (ETDEWEB)

    Galitsky, Christina; Price, Lynn; Zhou, Nan; Fuqiu , Zhou; Huawen, Xiong; Xuemin, Zeng; Lan, Wang

    2008-07-30

    The Benchmarking and Energy Savings Tool (BEST) Cement is a process-based tool based on commercially available efficiency technologies used anywhere in the world applicable to the cement industry. This version has been designed for use in China. No actual cement facility with every single efficiency measure included in the benchmark will likely exist; however, the benchmark sets a reasonable standard by which to compare for plants striving to be the best. The energy consumption of the benchmark facility differs due to differences in processing at a given cement facility. The tool accounts for most of these variables and allows the user to adapt the model to operational variables specific for his/her cement facility. Figure 1 shows the boundaries included in a plant modeled by BEST Cement. In order to model the benchmark, i.e., the most energy efficient cement facility, so that it represents a facility similar to the user's cement facility, the user is first required to input production variables in the input sheet (see Section 6 for more information on how to input variables). These variables allow the tool to estimate a benchmark facility that is similar to the user's cement plant, giving a better picture of the potential for that particular facility, rather than benchmarking against a generic one. The input variables required include the following: (1) the amount of raw materials used in tonnes per year (limestone, gypsum, clay minerals, iron ore, blast furnace slag, fly ash, slag from other industries, natural pozzolans, limestone powder (used post-clinker stage), municipal wastes and others); the amount of raw materials that are preblended (prehomogenized and proportioned) and crushed (in tonnes per year); (2) the amount of additives that are dried and ground (in tonnes per year); (3) the production of clinker (in tonnes per year) from each kiln by kiln type; (4) the amount of raw materials, coal and clinker that is ground by mill type (in tonnes per

  8. Impacts of cement industries on environment and control measure

    International Nuclear Information System (INIS)

    Hashmi, H.N.; Malik, H.N.; Naushad, Z.

    2005-01-01

    Utilization of cement as building material is gaining more importance. Cement industries around the world are contributing in global and as well as local pollution. In Pakistan most of the cement industries are constructed in remote areas without any proper environmental impact assessment. Unawareness of peoples toward sustainable environment and due to lack of job opportunities, dwellers are demanding employment rather than clean environment from title-holder of the industry. Air pollution caused by cement industries is harmful to the human's health, spoils and erodes building surface, corrodes metals, weakens textiles, deteriorates atmospheric visibility, affects plant life and leads to ecological imbalances. To investigate environmental impact of cement industries in Pakistan, environmental conditions around and inside the five cement industries in the vicinity of Taxila city are studied. To inspect the whole scenario, air pollution control devices in these industries were also examined in detail. These industries are using Electrostatic Precipitators and Baghouses to control air pollution (dust particulates). Proper caring of these equipment is necessary for better results. Detailed study shows that emissions from their stacks and dust particulates are causing problems. Health consultants in study area are much worry about the health of workers and environmental degradation in the vicinity of these industries. The comparison of air pollution control devices shows that Baghouses are environmental friendly. Considering the field conditions it is also concluded that involvement of government and environmental pollution control agencies is much more necessary. (author)

  9. Using dehydrated cement paste as new type of cement additive

    NARCIS (Netherlands)

    Yu, R.; Shui, Z.H.; Dong, J

    2013-01-01

    This paper presents an experimental study, including evaluation and modification, on using dehydrated cement paste (DCP) as a new type of cement additive. After a series of processes, normal DCP (N-DCP) was produced as before and a modified form of DCP (M-DCP) was produced as well. The cementitious

  10. The Fogging Method with Variable of Nozle Diameter as the Mitigation Alternative for Spreading the Dust of Cement

    Science.gov (United States)

    Purwanta, J.; Marnoto, T.; Setyono, P.; Ramelan, A. H.

    2018-03-01

    The cement plant impacts on the lives of people around the factory site, one of them on the air quality, especially dust. Cement plant has made various efforts to mitigate dust generated, but the reality on the ground is still a lot of dust flying around either of the cement factory chimneys and transportation. The purpose of this study was to find the optimum condition of nozle diameter from the cement dust catcher, for mitigation the dust spread to around the cement plant. This study uses research methods such as collecting secondary data which includes data intensity rainfall, the average long rains, wind speed and direction as well as data quality monitoring dust around PT. Semen Gresik (Persero) Tbk. Tuban plant. To determine the wind direction propensity models, use a soft Windrose file. To determine the impact on the spread of dust into the environment using secondary data monitoring air quality. Results of the study is that the mitigation of dust around the cement plant is influenced by natural factors, namely the tendency of wind direction, rainfall and rainy days, and the rate of dust emission from the chimney. I try for operate the cement dust catcher with variable of nozle diameter. Finally, I find the optimum condition of nozle diameter for cement dust catcher is 1.40 mm, with line equation is y = 149.09.e 1.6237.x and error 5%. In that condition, nozle can make the fog with a good quality and it can catch the cement dust well.

  11. Cement manufacture and the environment - Part I: Chemistry and technology

    Science.gov (United States)

    Van Oss, H. G.; Padovani, A.C.

    2002-01-01

    Hydraulic (chiefly portland) cement is the binding agent in concrete and mortar and thus a key component of a country's construction sector. Concrete is arguably the most abundant of all manufactured solid materials. Portland cement is made primarily from finely ground clinker, which itself is composed dominantly of hydraulically active calcium silicate minerals formed through high-temperature burning of limestone and other materials in a kiln. This process requires approximately 1.7 tons of raw materials perton of clinker produced and yields about 1 ton of carbon dioxide (CO2) emissions, of which calcination of limestone and the combustion of fuels each contribute about half. The overall level of CO2 output makes the cement industry one of the top two manufacturing industry sources of greenhouse gases; however, in many countries, the cement industry's contribution is a small fraction of that from fossil fuel combustion by power plants and motor vehicles. The nature of clinker and the enormous heat requirements of its manufacture allow the cement industry to consume a wide variety of waste raw materials and fuels, thus providing the opportunity to apply key concepts of industrial ecology, most notably the closing of loops through the use of by-products of other industries (industrial symbiosis). In this article, the chemistry and technology of cement manufacture are summarized. In a forthcoming companion article (part II), some of the environmental challenges and opportunities facing the cement industry are described. Because of the size and scope of the U.S. cement industry, the analysis relies primarily on data and practices from the United States.

  12. Accurate quantitative XRD phase analysis of cement clinkers

    International Nuclear Information System (INIS)

    Kern, A.

    2002-01-01

    Full text: Knowledge about the absolute phase abundance in cement clinkers is a requirement for both, research and quality control. Traditionally, quantitative analysis of cement clinkers has been carried out by theoretical normative calculation from chemical analysis using the so-called Bogue method or by optical microscopy. Therefore chemical analysis, mostly performed by X-ray fluorescence (XRF), forms the basis of cement plan control by providing information for proportioning raw materials, adjusting kiln and burning conditions, as well as cement mill feed proportioning. In addition, XRF is of highest importance with respect to the environmentally relevant control of waste recovery raw materials and alternative fuels, as well as filters, plants and sewage. However, the performance of clinkers and cements is governed by the mineralogy and not the elemental composition, and the deficiencies and inherent errors of Bogue as well as microscopic point counting are well known. With XRD and Rietveld analysis a full quantitative analysis of cement clinkers can be performed providing detailed mineralogical information about the product. Until recently several disadvantages prevented the frequent application of the Rietveld method in the cement industry. As the measurement of a full pattern is required, extended measurement times made an integration of this method into existing automation environments difficult. In addition, several drawbacks of existing Rietveld software such as complexity, low performance and severe numerical instability were prohibitive for automated use. The latest developments of on-line instrumentation, as well as dedicated Rietveld software for quantitative phase analysis (TOPAS), now make a decisive breakthrough possible. TOPAS not only allows the analysis of extremely complex phase mixtures in the shortest time possible, but also a fully automated online phase analysis for production control and quality management, free of any human interaction

  13. Biomass for green cement

    Energy Technology Data Exchange (ETDEWEB)

    Cumming, R. [Lafarge Canada Inc., Calgary, AB (Canada)

    2006-07-01

    Lafarge examined the use of waste biomass products in its building materials and provided background information on its operations. Cement kiln infrastructure was described in terms of providing access to shipping, rail and highways; conveying and off-loading equipment; having large storage facilities; and, offering continuous monitoring and stack testing. The presentation identified the advantages and disadvantages of a few different biomass cases such as coal; scrap tires; non-recyclable household waste; and processed biomass. A chart representing landfill diversion rates was presented and the presentation concluded with a discussion of energy recovery and recycling. 1 tab., figs.

  14. Container transport direct call – logistic solution to container transport via Estonia

    Directory of Open Access Journals (Sweden)

    A. Tolli

    2007-12-01

    Full Text Available Container transport in the world grows up to 12 % every year. Chinese container transport contributes majority of container flows in international container transport. Many world seaports compete for Chinese container flows and make eff orts to get investments and direct calls from China to their ports. Estonia has a possibility to decrease its large dependence and risks due to the transit of oil and oil products and coal with the help of container flows from China. In addition to a favorable geographical location Estonia has several other important arguments, like suffi cient land in the harbours for developing a container terminal to launch extensive container transport transit from China. Port of St. Petersburg, container transport port closest to Estonia by the Baltic Sea, is overloaded. Estonia can compete for container flows directed to Moscow, Nizhniy Novgorod, Kazan and Kaluga. Construction of an international high-tech container terminal in Port of Tallinn serves as one important precondition for directing Russian transit container flows through Estonia. Such a container terminal could service also larger vessels and container flows from China. Container lines and container terminals operating as alliances are jointly able to substantially increase container flows through countries.

  15. Process of preparing hydraulic cement

    Energy Technology Data Exchange (ETDEWEB)

    1919-12-11

    A process of preparing hydraulic cement from oil shale or shale coke is characterized in that the oil shale or shale coke after the distillation is burned long and hot to liberate the usual amount of carbonic acid and then is fine ground to obtain a slow hardening hydraulic cement.

  16. Health hazards of cement dust

    International Nuclear Information System (INIS)

    Meo, Sultan A.

    2004-01-01

    ven in the 21st century, millions of people are working daily in a dusty environment. They are exposed to different types of health hazards such as fume, gases and dust, which are risk factors in developing occupational disease. Cement industry is involved in the development of structure of this advanced and modern world but generates dust during its production. Cement dust causes lung function impairment, chronic obstructive lung disease, restrictive lung disease, pneumoconiosis and carcinoma of the lungs, stomach and colon. Other studies have shown that cement dust may enter into the systemic circulation and thereby reach the essentially all the organs of body and affects the different tissues including heart, liver, spleen, bone, muscles and hairs and ultimately affecting their micro-structure and physiological performance. Most of the studies have been previously attempted to evaluate the effects of cement dust exposure on the basis of spirometry or radiology, or both. However, collective effort describing the general effects of cement dust on different organ and systems in humans or animals, or both has not been published. Therefore, the aim of this review is to gather the potential toxic effects of cement dust and to minimize the health risks in cement mill workers by providing them with information regarding the hazards of cement dust. (author)

  17. Ceramic microspheres for cementing applications

    NARCIS (Netherlands)

    2011-01-01

    A method and apparatus for manufacturing ceramic microspheres from industrial slag. The microspheres have a particle size of about 38 microns to about 150 microns. The microspheres are used to create a cement slurry having a density of at least about 11 lbs/g. The resultant cement slurry may then be

  18. Ceramic microspheres for cementing applications

    NARCIS (Netherlands)

    2010-01-01

    A method and apparatus for manufacturing ceramic microspheres from industrial slag. The microspheres have a particle size of about 38 microns to about 150 microns. The microspheres are used to create a cement slurry having a density of at least about 11 lbs/g. The resultant cement slurry may then be

  19. Ceramic microspheres for cementing applications

    NARCIS (Netherlands)

    2012-01-01

    A method and apparatus for manufacturing ceramic microspheres from industrial slag. The microspheres have a particle size of about 38 microns to about 150 microns. The microspheres are used to create a cement slurry having a density of at least about 11 lbs/g. The resultant cement slurry may then be

  20. Moving the Field Forward: A Micro-Meso-Macro Model for Critical Language Planning. The Case of Estonia

    Science.gov (United States)

    Skerrett, Delaney Michael

    2016-01-01

    This study investigates "de facto" language policy in Estonia. It investigates how language choices at the micro (or individual) level are negotiated within the macro (or social and historical) context: how official language policy and other features of the discursive environment surrounding language and its use in Estonia translate into…

  1. Radiocarbon dating in the quarternary geology and archaeology of Estonia

    International Nuclear Information System (INIS)

    Ilves, Eh.; Liiva, A.; Punning, Ya.M.

    1974-01-01

    Work of the Tartusk radiocarbon laboratory for the last 15 years is presented. Methodological problems of the radiocarbon method are discussed. The geochemistry of carbon isotopes, principles of radiocarbon dating, and areas of its application are considered. Methods of recording natural radiocarbon and materials used for radiocarbon dating are discussed. Preliminary treatment of the samples and synthesis of the radioactive carbon carrier are presented. The preparation of the counter compound in the form of a liquid scintillator from the synthesized natural radiocarbon carrier is described. The scintillator efficiencies of different scintillators are compared. Data are given on the development of criteria for selecting the photoelectron multiplier. Construction of alumina cuvettes used for scintillation counting is described. It is noted that, in the counter apparatus system, amplitude analyzers with two differential discriminators are used, which allows directing the recording of activity to two 14 C regions. The results of using the radiocarbon method for different aspects of natural science and archeology are considered. Problems of geology of the late Pleistocene and the Pre-Baltic Holocene are considered: base of the mid-Valdaisk Karukyulask interglacier, history of deterioration of the final glacial mantle, development of a drainage system and late glacier, development and paleography of the Holocene, and others. New material on the chronology of primeval cultures in the Estonia region and on growth of meteoric craters are presented

  2. Women in Physics in Estonia: Many Duties, One Life

    Science.gov (United States)

    Kaasik, Helle

    2009-04-01

    In Estonia, women and men have equal legal rights. Women are expected to earn their living like men—and unlike men, to be the main (often the only) caregiver for the children. In the family women do most of the unpaid work, spending twice the amount of time on household duties as men. Laws about public preschool child care and child support obligations for noncustodial parents exist, but these laws are not always realized in practice. A generous policy of benefits for children under 1.5 years provides some relief for mothers. It is a challenge to balance a woman's traditional load of unpaid duties with the high demands of a science career. As in many other countries, with every step up the academic ladder the underrepresentation of women in science becomes more evident. Physics and engineering are perceived as male areas and women active in these areas are often treated as exceptions. Most obstacles met by women in science are difficult to recognize and neutralize because they are deeply informal. Activities for "gender and science" that exceed the limits of sociological study have no long tradition here and are yet finding their place in Estonian society.

  3. Partnership dynamics among migrants and their descendants in Estonia

    Directory of Open Access Journals (Sweden)

    Leen Rahnu

    2015-06-01

    Full Text Available Background: Extensive scholarly literature documents the decline in marriage and increase in non-marital cohabitation and divorce across regions and countries of Europe, but we know less about the extent to which these new family behaviours that have emerged in host societies are adopted by migrants. Objective: The aim of this study is to examine partnership transitions among the migrants and their descendants in Estonia, who mainly originate from the European part of Russia. By investigating an East European context, the study contributes to a more comprehensive account of migrant populations in different socio-economic and cultural settings. Methods: The study is based on the Estonian Generations and Gender Survey (2004/2005 and the Estonian Family and Fertility Survey (1994/1997, and employs proportional hazards models. Results: The results show that new family formation patterns, associated with the Second Demographic Transition, are less prevalent among migrants. The difference between migrants and native Estonians is most pronounced in the mode of partnership formation and outcomes of cohabiting unions, whereas the results pertaining to union dissolution reveal a less systematic difference between population groups. Reflecting the relatively slow integration, the second-generation migrants exhibit partnership behaviour that differs from that of the native population. The observed differences between migrants and the native population appear largely similar for both men and women. Conclusions: The results lend support to socialisation, cultural maintenance, and adaptation hypotheses, and underscore the importance of contextual factors. The analysis reveals disruption effects of migration on partnership processes.

  4. Remediation of an oily leachate pond in Estonia.

    Science.gov (United States)

    Kriipsalu, Mait; Marques, Marcia; Hogland, William

    2005-12-01

    Until recent years, waste oil and oil-contaminated waters commonly ended up in landfills. At some dump sites, ponds of oily liquids and leachate were formed. To remediate such ponds, an interdisciplinary approach is now required, keeping costs at an affordable level, particularly in countries with changing economies. From 1974 to 1993, liquid oily wastes taken to the Laguja landfill, in Estonia, were disposed of in a pond with a surface area of 9800 m2. It was estimated that the pond contained 4500-6000 m3 of oily water and 3500 m3 of oil-containing bottom sediments. This study aimed at developing an environmentally sound and cost-effective method for remediation of the oily liquids, leachate and contaminated underlying sediment material, to meet the existing legal demands. It was concluded that treatment of contaminated water is well established and the procedures carried out to meet the regulatory demands achieved satisfactory results. However, regarding treatment of sediments it was concluded that legal and technological aspects, as well as monitoring procedures are not fully established and are usually underestimated. Laboratory investigations can provide valuable information in decision-making, and contribute to effective full-scale remediation planning.

  5. On the lower boundary of the Floian Stage in Estonia

    Directory of Open Access Journals (Sweden)

    Helje Pärnaste

    2012-11-01

    Full Text Available The lower boundary of the Second Stage of the Lower Ordovician Series, the Floian Stage, is defined by the first appearance of the graptolite Tetragraptus approximatus. In the stratotype section of Diabasbrottet at Hunneberg, southern Sweden, the boundary falls within the Megistaspis planilimbata trilobite Zone and within the Oelandodus elongatus–Acodus deltatus deltatus conodont Subzone of the Paroistodus proteus Zone, and within the Hunneberg Regional Stage. Graptolites, including the index species T. approximatus, are missing in the terrigenous sediment of Estonia. The earliest trilobites are poorly preserved in this terrigenous succession. They represent an interval older than the Megalaspides dalecarlicus Zone but probably younger than the M. planilimbata Zone, and are correlative to the Prioniodus elegans conodont Zone. Thus the lower boundary of the Second Stage can be detected using mainly conodonts. In accordance with conodont occurrence, the base of the Floian (i.e. somewhat higher than the base of the O. elongatus–A. d. deltatus Subzone falls within the Joa Member of the Leetse Formation. Probable levels have been suggested in some localities. Thus the lower part of the Leetse Formation belongs to the Tremadoc Stage, and to the Hunneberg Regional Stage.

  6. Hazardous substances in the aquatic environment of Estonia.

    Science.gov (United States)

    Roots, Ott; Roose, Antti

    2013-09-01

    The Water Framework Directive (WFD) aims to regulate the management of European surface water bodies. Directive 2008/105/EC, which establishes the environmental quality standards of priority substances and certain other pollutants, the content of which in the surface water should be monitored, has been transposed by the Estonian Ministry of Environment 9 September 2010 Regulation No. 49. Sampled hazardous substances were selected primarily based on their toxicity, as well as their lifetime in environment and ability to accumulate in living organisms (bioaccumulation). The contents of hazardous substances and their groups determined from Estonian surface waters remained below the limits of quantifications of used analysis methods in most cases. However, the content of some heavy metals, mono- and dibasic phenols in the surface water/waste water and sewage sludge/bottom sediments can still reach the delicate levels in the Estonian oil shale region in particular. Among new substances analysed in Estonia historically first time in 2010, amounts of organotin compounds in sediments and some alkylphenols, their ethoxylates and phthalates were found in various sample matrices. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Effectiveness of Environmental Impact Assessment system in Estonia

    International Nuclear Information System (INIS)

    Heinma, Kaupo; Poder, Tonis

    2010-01-01

    To be effective, an Environmental Impact Assessment (EIA) system, first, has to minimize the probability that projects with significant environmental effects are implemented without EIA, and second, minimize the number of EIAs, which do not provide decision makers with essential information, so that the decision is improved as a result of EIA. The objective of this study was to find out how frequently in Estonia the projects implemented without EIA have caused significant environmental effects, and to measure the relative frequency of EIAs that have no influence on decision. An extensive survey with e-mail distributed questionnaires was carried out to reveal information from governmental agencies, local self-governments, and developers. There was no evidence that projects authorized without EIA have had environmental impacts, which could have been mitigated as a result of EIA. In contrast, about half of EIAs did not alter the decision of relevant authorities. This proportion was valid to both mandatory EIAs and those initiated on judgement basis. In our view, the proportion of no-influence EIAs was excessive and indicated the need to reconsider the provisions applying to the projects with a mandatory EIA requirement as well as judgements practice.

  8. Conodont dating of some Telychian (Silurian sections in Estonia

    Directory of Open Access Journals (Sweden)

    Männik, Peep

    2008-09-01

    Full Text Available Several Telychian–Sheinwoodian strata exposed in Estonia are precisely dated using conodont biostratigraphy. The beds in the Valgu-1 section correspond to the uppermost Distomodus staurognathoides and Pterospathodus eopennatus ssp. n. 1 zones. In the Valgu-2 and Valgu-3 sections only the P. eopennatus ssp. n. 1 Zone is exposed. The strata in the Velise-Kõrgekalda section correspond to the Lower subzone of the P. amorphognathoides angulatus Zone. Marlstones in the Jädivere section are assigned to the P. a. lennarti Zone. In the Avaste section part of the P. a. lithuanicus Zone is exposed. On the Saastna Peninsula two stratigraphical intervals, the lower corresponding to the Upper subzone of the P. a. amorphognathoides Zone and the upper to the Upper Kockelella ranuliformis Zone, crop out along the shoreline. In Saastna the exposed strata are separated by a covered interval corresponding to five conodont zones, from the Lower Pseudooneotodus bicornis Zone to the Lower K. ranuliformis Zone.

  9. Corrosion resistant cemented carbide

    International Nuclear Information System (INIS)

    Hong, J.

    1990-01-01

    This paper describes a corrosion resistant cemented carbide composite. It comprises: a granular tungsten carbide phase, a semi-continuous solid solution carbide phase extending closely adjacent at least a portion of the grains of tungsten carbide for enhancing corrosion resistance, and a substantially continuous metal binder phase. The cemented carbide composite consisting essentially of an effective amount of an anti-corrosion additive, from about 4 to about 16 percent by weight metal binder phase, and with the remaining portion being from about 84 to about 96 percent by weight metal carbide wherein the metal carbide consists essentially of from about 4 to about 30 percent by weight of a transition metal carbide or mixtures thereof selected from Group IVB and of the Periodic Table of Elements and from about 70 to about 96 percent tungsten carbide. The metal binder phase consists essentially of nickel and from about 10 to about 25 percent by weight chromium, the effective amount of an anti-corrosion additive being selected from the group consisting essentially of copper, silver, tine and combinations thereof

  10. Alternative fuels in cement industry; Alternativa braenslen i cementindustrin

    Energy Technology Data Exchange (ETDEWEB)

    Nyman, K.E.; Ek, R. [Finnsementti Oy, Parainen (Finland); Maekelae, K. [Finreci Oy (Finland)

    1997-10-01

    In this project the cement industry`s possibilities to replace half of the fossil fuels with waste derived fuels are investigated. Bench-scale experiments, pilot plant tests and full scale tests have been done with used tires and plastics wastes

  11. Scenarios for shale oil, syncrude and electricity production in Estonia in the interim 1995-2025

    International Nuclear Information System (INIS)

    Oepik, I.

    1992-01-01

    This paper is based on the author's pre-feasibility studies of oil shale utilization in oil production, electricity generation and cement industry. The electricity generation has been calculated on the basis of 1.4 and 1.6 GW oil shale power plants with pulverized fuel combustion today. The three scenarios OILMIN, OILMED and OILMAX differ by annual oil production and different investment costs. The investments in the oil shale processing industry seem to be more profitable than those in electricity generation. It is also important to take into account that the very high sensitivity of oil market to geopolitical aspects of resources and to sudden crises, makes the crude price a stochastic parameter, which loses its indicative character for long term economic choice. Therefore it will be very important to have the electric power plants with flexible combined oil shale and coal combustion. 4 figs., 4 tabs., 6 refs

  12. An inplementation strategy for the utilization of wind energy in Estonia. Phase 1: Pre-feasibility study and project identification. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    This report presents the results of a pre-feasibility and project identification study with the purpose of investigating the possibilities for wind energy in Estonia and to recommend on possible actions, as outlined in Letters of Interest from the Estonian Ministries of Economy and Environment in 1995. Wind as source of energy in Estonia appears not yet to have been analyzed in detail. Available data indicates that wind can constitute a viable domestic source of energy, as average wind speeds of about 6 m/s (at 10 m) are reported at many coastal regions of Estonia. With state-of-the-art wind energy technology this means cost of wind produced electricity about 0.7-0.8 EEK/kWh - comparable to the cost of electricity from a modern coal-fired power plant. Two types of grids exist in these regions: On the mainland and on islands with sea cable grid connected wind turbines can be implemented. On islands without sea cable wind turbines can be connected to the diesel powered local grids. As a first step it is proposed to undertake the detailed planning and feasibility study of grid connected wind energy demonstrations in the framework of the Danish-Estonian country collaboration agreement. If the decision is made to implement this wind energy demonstration project, a certain proportion of grant money should be allocated for the demonstration. Subsequent steps in the Danish-Estonian country collaboration agreement should include the detailed planning and feasibility studies of autonomous wind energy demonstration and the associated capacity building. (EG)

  13. Predictors and consequences of job insecurity: Comparison of Slovakia and Estonia

    Directory of Open Access Journals (Sweden)

    Lucia Ištoňová

    2016-03-01

    Full Text Available Job insecurity is a significant current social issue in many European countries. Slovakia and Estonia significantly differ in the prevalence of job insecurity. The main aim of the present study was to compare Slovakia and Estonia in regard to job insecurity by looking at socio-demographic, job and organisational predictors and individual and social consequences based on ESS round five data. The secondary aim was to examine relationships between job insecurity and its predictors as well as job insecurity and its consequences. The analysis covered employed people with unlimited or limited contracts, working 40-50 hours per week, within the age range of 20-60. The results suggested significant differences in the predictors of job insecurity for Slovakia and Estonia. However, the individual, social and economic consequences of job insecurity were similar for both countries. This study contributes to an enhanced understanding of job insecurity predictors and consequences in the European region.

  14. The incorporation of low and medium level radioactive wastes (solids and liquids) in cement

    International Nuclear Information System (INIS)

    Brown, D.J.; Capp, P.D.; Smith, D.L.

    1982-08-01

    Laboratory studies and mixing plant trials on simulated radioactive waste formulations are reported. Long term stability testing of various formulations including those containing blast furnace slag-ordinary Portland cement, sodium nitrate, ion exchange resins, and sodium nitrate-tributyl phosphate, are reported and some results are given. Mixing plant trials with a high shear cement mixer are reported. An outline of future work is presented. (U.K.)

  15. Radon exhalation study from cement, cement slabs and concrete slabs with variation in fly ash

    International Nuclear Information System (INIS)

    Sharma, Nisha; Singh, Jaspal

    2012-01-01

    Fly ash is a waste product from coal-fired power plants. Fly ash has become a subject of world-wide interest in recent years because of its diverse uses, e.g. in the manufacture of concrete for building purposes, for the filling of underground cavities, or as a component of building material. The fly ash may contain enhanced levels of the natural radionuclides in the uranium and thorium series and by using the fly ash in building materials, the radiation levels in houses may thus be technologically enhanced. Because of its relatively high radionuclide contents (including 226 Ra), fly ash may, however, present a potential hazard to the population through its radon emanation, which would be highly undesirable. Since fly ash is frequently used as a building material, the idea of the experiment was to mix fly ash in different proportions in the cement in the powder form, cemented slabs and concrete slabs to study the combined behaviors. Alpha sensitive LR-115 type II plastic track detector, commonly known as Solid State Nuclear Track Detectors (SSNTDs), were used to measure the radon concentration. The alpha particles emitted from the radon causes the radiation damaged tracks. The chemical etching in NaOH at 60°C for about 90 minutes was done to reveal these latent tracks, which were then scanned and counted by an optical microscope of suitable magnification. By calculating the track density of registered tracks, the radon concentrations were determined. In case of cement in the powder form and in cemented slab, starting from the pure cement, fly ash was added up to 70% by weight. In this case the radon exhalation rate has increased by addition of fly ash in the cement and in case of concrete slabs by the addition of fly ash in the cement the radon exhalation increases up to 60% and then decreases. Therefore, on the basis of our investigations we concluded that in general radon exhalation rate increases with the addition of fly ash. (author)

  16. Different Labelling of Obstructive Airway Diseases in Estonia, Finland, and Sweden

    International Nuclear Information System (INIS)

    Pallasaho, Paula; Meren, Mari; Raukas-Kivioja, Aet; Roenmark, Eva

    2005-01-01

    Large differences in prevalence of asthma have been reported between westernised countries and the former Eastern European countries, and still no consensus about the reasons for the differences exists. The aim of this study was to assess diagnostic labelling of obstructive airway diseases, comparing subjects with respiratory symptoms and the diagnoses obtained in Estonia, Finland, and Sweden. A postal questionnaire was sent to population-based random samples, and 44,483 (76%) answers were obtained from the 58,661 invited in 1996. Among men, current smoking was most common in Estonia, 60%, followed by Finland, 39%, and Sweden, 28%. In all three countries, 30% of women were current smokers. Most respiratory symptoms including wheezing were most common in Estonia, also among non-smokers. The prevalence of asthma was 2.0% and chronic bronchitis 10.7% in Estonia, while the opposite was found in Sweden with an asthma prevalence of 7.8% and a chronic bronchitis prevalence of 3.1%. The pattern in Finland was similar to that of Sweden. The same differences between the three countries were found also among young subjects. The total proportion of diagnosed obstructive lung diseases in subjects with respiratory symptoms was similar, but the diagnosis of asthma was considerably more common in Finland and Sweden. Chronic bronchitis was favoured in Estonia, also among young adults irrespectively of what symptoms were present. In a multivariate model with correction for confounders, the risk (OR) for having a diagnosis of asthma was 5.65 (95% CI: 4.86-6.56) when living in Sweden, and 3.51 (95% CI: 3.00-4.12) in Finland, whereas risk for chronic bronchitis was 0.28 (0.25-0.31) and 0.22 (0.19-0.25), respectively, compared to Estonia. The study indicates differences in diagnostic practices of obstructive lung diseases between the three countries

  17. Immobilization in cement of ion exchange resins from Spanish nuclear reactors

    International Nuclear Information System (INIS)

    Huebra, A.G. de la; Murillo, R.; Ortiz, S.J.

    1990-01-01

    Ion exchange materials used at nuclear power plants can be immobilized in cements less expensive than polymer matrices. Cement solidification of spent ion exchange resins shows swelling and cracking troubles (during setting time, or of storage). The objective of this study was to select the types of cement that produce the best quality on immobilization of three kinds of resins and to set up cement formulations containing the maximum possible loading of resin. Four cements were selected to carried out the study. After a study of hydration-dehydration phenomena of ion exchange resins, a systematic work has been carried out on immobilization. Tests were performed to study compressive strength and underwater stability by changing water/cement ratio and resin/cement ratio. Mixtures made with water, cement and resin only were loaded with 10% by weight dry resin. Mixtures with higher loadings show poor workability. Tests were carried out by adding organic plasticizers and silica products to improve waste loading. Plasticizers reduced water demand and silica products permit the use of more water. Leaching tests have been performed at 40 O C. In conclusion Blast Furnace Slag is the best cement for immobilization of ion exchange resin both bead and powdered form for mechanical strength, stability and leaching

  18. 21 CFR 888.4200 - Cement dispenser.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cement dispenser. 888.4200 Section 888.4200 Food... DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.4200 Cement dispenser. (a) Identification. A cement dispenser is a nonpowered syringe-like device intended for use in placing bone cement (§ 888.3027) into...

  19. Energy conservation and dust production in wet rotary cement kilns

    Energy Technology Data Exchange (ETDEWEB)

    Sell, N J; Fischbach, F A

    1976-12-01

    Energy conservation is currently a major concern of the cement industry. A comparison of data supplied by the U.S. Federal Energy Administration with that gathered in an extensive private study incorporating 29 wet cement plants indicates that a significant reduction of the energy consumed can be accomplished by decreasing the amount of dust generated in the process. Energy saving of 8 percent through dust suppression appears possible by increasing the slurry moisture and by using hammermills rather than impactors as the crushing technique.

  20. Overview of the electricity market of Estonia and the plausibility of nuclear energy production

    International Nuclear Information System (INIS)

    Lehtveer, M.; Tkaczyk, A.

    2010-01-01

    The Republic of Estonia is a small country in Northern Europe, with electrical energy production dependent mostly on oil shale. The local supply of oil shale has given Estonia its energetic independence but it also presents great challenges: it is waste-intensive and causes massive emission of greenhouse gases into the atmosphere. It also causes damage to the landscape and to the health of the population living near the mining and energy producing area. Due to the above mentioned problems the use of nuclear power has been taken into consideration, but the debate is at its beginning and the need for further analyses is great

  1. Estonia in the system of global climate change. Publication 4/1996

    International Nuclear Information System (INIS)

    Punning, J.M.

    1996-01-01

    Estonia is among the countries who signed the Framework Convention on Climate Change (FCCC) at the UN Conference in Rio de Janeiro in June 1992. The FCCC calls on its parties to inventory national sources, to reduction in greenhouse gases and to development of projects responding to climate change. In 1994, an Estonian Country Study Project was initiated within the U.S. Country Studies Program. The Estonian Country Study Project is comprehensive, covering all sectors and directions of activity in Estonia that might impact climate change or be influenced by Global Climate Change. This book contains a collection of papers, covering the aims of the Estonian Country Study Project

  2. A cement based syntactic foam

    International Nuclear Information System (INIS)

    Li Guoqiang; Muthyala, Venkata D.

    2008-01-01

    In this study, a cement based syntactic foam core was proposed and experimentally investigated for composite sandwich structures. This was a multi-phase composite material with microballoon dispersed in a rubber latex toughened cement paste matrix. A trace amount of microfiber was also incorporated to increase the number of mechanisms for energy absorption and a small amount of nanoclay was added to improve the crystal structure of the hydrates. Three groups of cement based syntactic foams with varying cement content were investigated. A fourth group of specimens containing pure cement paste were also prepared as control. Each group contained 24 beam specimens. The total number of beam specimens was 96. The dimension of each beam was 30.5 cm x 5.1 cm x 1.5 cm. Twelve foam specimens from each group were wrapped with plain woven 7715 style glass fabric reinforced epoxy to prepare sandwich beams. Twelve cubic foam specimens, three from each group, with a side length of 5.1 cm, were also prepared. Three types of testing, low velocity impact test and four-point bending test on the beam specimens and compression test on the cubic specimens, were conducted to evaluate the impact energy dissipation, stress-strain behavior, and residual strength. Scanning electron microscope (SEM) was also used to examine the energy dissipation mechanisms in the micro-length scale. It was found that the cement based syntactic foam has a higher capacity for dissipating impact energy with an insignificant reduction in strength as compared to the control cement paste core. When compared to a polymer based foam core having similar compositions, it was found that the cement based foam has a comparable energy dissipation capacity. The developed cement based syntactic foam would be a viable alternative for core materials in impact-tolerant composite sandwich structures

  3. Crown and bridge cements: clinical applications.

    Science.gov (United States)

    Bunek, Sabiha S; Powers, John M

    2012-12-01

    Cement selection can be confusing because factors such as substrate, the type of restoration, and patient needs must be considered. Some substrates require additional treatment before cementation. This article describes the most commonly used traditional crown and bridge cements (GI and RMGI) used for metal and metal-ceramic restorations, and resin cements used for all-ceramic restorations. Advantages, disadvantages, indications, and contraindications of cements have been reviewed. Recommended uses of cements for metal, ceramic, and laboratory composite restorations have been presented. General guidelines for surface treatment ot silica- and zirconia-based restorations when using resin cements have been discussed.

  4. Cement/slag chemistry studies

    International Nuclear Information System (INIS)

    Glasser, F.P.; Macphee, D.; Atkins, M.; Beckley, N.; Carson, S.O.; Wilding, C.R.; McHugh, G.

    1988-01-01

    The performance of cement-based matrices intended for radwaste immobilization is assessed. The long-term performance of the matrix is characterized by thermodynamic evaluation of experimental data. The results are presented in a general form, amenable to a range of specific formulations. The interaction of specific radwaste components with cements has been studied, using Iodine as an example. It occurs as both I - and IO 3 - species, but these differ sharply in sorption characteristics. The effect of ionizing radiation of the pH and E h of cement matrices is reported. (author)

  5. Cements in Radioactive Waste Disposal

    International Nuclear Information System (INIS)

    Glasser, F.P.

    2013-01-01

    The use of cement and concrete to immobilise radioactive waste is complicated by the wide- ranging nature of inorganic cementing agents available as well as the range of service environments in which cement is used and the different functions expected of cement. For example, Portland cement based concretes are widely used as structural materials for construction of vaults and tunnels. These constructions may experience a long pre-closure performance lifetime during which they are required to protect against collapse and ingress of water: strength and impermeability are key desirable characteristics. On the other hand, cement and concrete may be used to form backfills, ranging in permeability. Permeable formulations allow gas readily to escape, while impermeable barriers retard radionuclide transport and reduce access of ground water to the waste. A key feature of cements is that, while fresh, they pass through a fluid phase and can be formed into any shape desired or used to infiltrate other materials thereby enclosing them into a sealed matrix. Thereafter, setting and hardening is automatic and irreversible. Where concrete is used to form structural elements, it is also natural to use cement in other applications as it minimises potential for materials incompatibility. Thus cement- mainly Portland cement- has been widely used as an encapsulant for storage, transport and as a radiation shield for active wastes. Also, to form and stabilise structures such as vaults and silos. Relative to other potential matrices, cement also has a chemical immobilisation potential, reacting with and binding with many radionuclides. The chemical potential of cements is essentially sacrificial, thus limiting their performance lifetime. However performance may also be required in the civil engineering sense, where strength is important, so many factors, including a geochemical description of service conditions, may require to be assessed in order to predict performance lifetime. The

  6. Cements in Radioactive Waste Disposal

    Energy Technology Data Exchange (ETDEWEB)

    Glasser, F. P. [University of Aberdeen, Scotland (United Kingdom)

    2013-09-15

    The use of cement and concrete to immobilise radioactive waste is complicated by the wide- ranging nature of inorganic cementing agents available as well as the range of service environments in which cement is used and the different functions expected of cement. For example, Portland cement based concretes are widely used as structural materials for construction of vaults and tunnels. These constructions may experience a long pre-closure performance lifetime during which they are required to protect against collapse and ingress of water: strength and impermeability are key desirable characteristics. On the other hand, cement and concrete may be used to form backfills, ranging in permeability. Permeable formulations allow gas readily to escape, while impermeable barriers retard radionuclide transport and reduce access of ground water to the waste. A key feature of cements is that, while fresh, they pass through a fluid phase and can be formed into any shape desired or used to infiltrate other materials thereby enclosing them into a sealed matrix. Thereafter, setting and hardening is automatic and irreversible. Where concrete is used to form structural elements, it is also natural to use cement in other applications as it minimises potential for materials incompatibility. Thus cement- mainly Portland cement- has been widely used as an encapsulant for storage, transport and as a radiation shield for active wastes. Also, to form and stabilise structures such as vaults and silos. Relative to other potential matrices, cement also has a chemical immobilisation potential, reacting with and binding with many radionuclides. The chemical potential of cements is essentially sacrificial, thus limiting their performance lifetime. However performance may also be required in the civil engineering sense, where strength is important, so many factors, including a geochemical description of service conditions, may require to be assessed in order to predict performance lifetime. The

  7. Status and management of noble crayfish Astacus astacus in Estonia

    Directory of Open Access Journals (Sweden)

    T. Paaver

    2009-01-01

    Full Text Available Noble crayfish Astacus astacus (L. is an indigenous and the only crayfish species in Estonia. It is potentially endangered by invasion of alien species, diseases and habitat deterioration but does not have legal protected status and is fished only for recreational purpose. Crayfish Working Group of Ministry of Environment and Department of Aquaculture of the Estonian University of Life Sciences have developed crayfish conservation and management plan. Since 1994 standardized test fishing with traps (which catch only crayfish over 7 cm TL has been carried out and database of these fishings shows, that crayfish is dwelling in more than 255 sites in the lakes, rivers, streams, artificial reservoirs. In 52% of monitored sites populations are weak, catch per trap night is below 1 specimen. Exceptionally rich is the stock on the island Saaremaa, where in 59% of populations catch per trap night is over 4 and can reach 50. Licensed recreational catch is allowed in regions, where monitoring data show good status of crayfish stock. It is not allowed to sell the crayfish caught on recreational license. Crayfishing season is limited with August, size limit in recreational fishery is 11 cm TL. There are 10 operating crayfish farms and 15 are under construction. The farms produce yearly around 1000 kg of commercial size crayfish for export to Finland. Over 200000 juveniles are produced for restocking yearly. Restocking projects e.g. restoration of populations, which have been lost because of plague have been successful. The main threat factor is crayfish plague. In 2006–2007 it destroyed the stock of crayfish farms of companies Veteko, Pähkla, Astacus and wild population of Põduste river on the island Saaremaa.

  8. Does cement mantle thickness really matter?

    OpenAIRE

    Caruana, J.

    2008-01-01

    The thickness of the cement mantle around the femoral component of total hip replacements is a contributing factor to aseptic loosening and revision. Nevertheless, various designs of stems and surgical tooling lead to cement mantles of differing thicknesses. This thesis is concerned with variability in cement thickness around the Stanmore Hip, due to surgical approach, broach size and stem orientation, and its effects on stress and cracking in the cement. The extent to which cement mantle thi...

  9. Fiscal 1999 technical survey report. Model project implementation feasibility study in India on cement calcination facilities waste heat recovery; 1999 nendo Indo ni okeru cement shosei setsubi hainetsu kaishu model jigyo jisshi kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    India produces 96-million tons/year of cement, ranking fourth in the world, and 55% of the yield comes from 1-million tons/year plants. Some of the waste heat from the manufacturing process is used to dry materials, etc., but much is discharged into the atmosphere. Estimation is made of the energy conservation effect expected to be brought about in case the waste heat power generation technology which is in use to good effect in Japan is introduced into Indian cement plants whose clinker production exceeds 3,000 tons/day. As the result, it is concluded that the model project may be implemented at any of the four plants for which power generation capability and CO2 reduction effect are tentatively calculated below. There will be power generation of 7,300kW and CO2 reduction of 43,125 tons for the Guijarat Ambuja Cement Ltd./Ambuja Cement Eastern plant; power generation of 7,700kW and CO2 reduction of 901,960 tons for the India Cement Ltd./Rassi Cement plant; power generation of 45,098kW and CO2 reduction of 1,140,220 tons for the Larsen and Toubro Ltd./Hirmi plant; and power generation of 5,450kW and CO2 reduction of 32,230 tons for the J. K. Corp Ltd./Lakshmi Cement Sirohi plant. (NEDO)

  10. Immobilisation of alpha contaminated lubricating oils in cement matrix

    International Nuclear Information System (INIS)

    Manohar, Smitha; Sathi Sasidharan, N.; Wattal, P.K.; Shah, N.J.; Chander, Mahesh; Bansal, N.K.

    2000-10-01

    Alpha contaminated lubricating oil wastes are generated from the reprocessing plants and other alpha handling facilities. Incineration of these spent lubricating oils requires specially designed facility to handle the aerosols of actinide oxides released to the off-gases. Hence immobilisation of these wastes into cement matrix could be a viable alternative. Work was therefore initiated to examine the possibility of immobilising such waste in cement matrix with the help of suitable additives. This work led to the selection of sodium hydroxide and silica fumes as additives for their distinct role in immobilization of such waste in cement. The selected formulation was tested extensively both on laboratory scale and full scale for acceptable waste form. The leach test on laboratory scale indicated negligible release of alpha and beta gamma activity after 180 days. This report gives a brief on the formulation of the admixture and its effect on the immobilization of waste. (author)

  11. Combustion of solid alternative fuels in the cement kiln burner

    DEFF Research Database (Denmark)

    Nørskov, Linda Kaare

    In the cement industry there is an increasing environmental and financial motivation for substituting conventional fossil fuels with alternative fuels, being biomass or waste derived fuels. However, the introduction of alternative fuels may influence emissions, cement product quality, process...... stability, and process efficiency. Alternative fuel substitution in the calciner unit has reached close to 100% at many cement plants and to further increase the use of alternative fuels rotary kiln substitution must be enhanced. At present, limited systematic knowledge of the alternative fuel combustion...... properties and the influence on the flame formation is available. In this project a scientific approach to increase the fundamental understanding of alternative fuel conversion in the rotary kiln burner is employed through literature studies, experimental combustion characterisation studies, combustion...

  12. The computer and the cement plant

    Directory of Open Access Journals (Sweden)

    Peirce, S. W.

    1966-06-01

    Full Text Available Not available¿Cuál es la razón para que la dirección de la fábrica de cemento ponga sus miras en el computador digital? No cabe la menor duda que esta razón radica en la eficacia y en la obtención de un producto de calidad. En los últimos años el interés se está centrando en la producción de cemento de mejor calidad, haciéndolo tan eficiente y económicamente como ello sea posible. La competencia así lo ha determinado. Cada proceso de la fabricación fue consecuentemente examinado, aplicándose mejoras técnicas en una rápida sucesión. Uno de los principales resultados fue la tendencia hacia fábricas de mayor envergadura, con hornos más grandes y con procesos de funcionamiento que son cada vez más automatizados. El gabinete de control centralizado constituye hoy día una instalación, en lugar de una curiosidad. En compañía de él viene un nuevo paso de instrumentación digital y analógica y, más recientemente, el sistema de computador digital totalmente normalizado para mejorar la eficacia operacional.

  13. Leaf structural traits of tropical woody species resistant to cement dust.

    Science.gov (United States)

    Siqueira-Silva, Advanio Inácio; Pereira, Eduardo Gusmão; Modolo, Luzia Valentina; Paiva, Elder Antonio Sousa

    2016-08-01

    Cement industries located nearby limestone outcrops in Brazil have contributed to the coating of cement dust over native plant species. However, little is known about the extent of the response of tropical woody plants to such environmental pollutant particularly during the first stages of plant development and establishment. This work focused on the investigation of possible alterations in leaf structural and ultrastructural traits of 5-month-old Guazuma ulmifolia Lam. (Malvaceae), 6-month-old Myracrodruon urundeuva Allemão (Anacardiaceae), and 9-month-old Trichilia hirta L. (Meliaceae) challenged superficially with cement dust during new leaf development. Leaf surface of plants, the soil or both (leaf plus soil), were treated (or not) for 60 days, under controlled conditions, with cement dust at 2.5 or 5.0 mg cm(-2). After exposure, no significant structural changes were observed in plant leaves. Also, no plant death was recorded by the end of the experiment. There was also some evidence of localized leaf necrosis in G. ulmifolia and T. hirta, leaf curling in M. urundeuva and T. hirta, and bulges formation on epidermal surface of T. hirta, after cement dust contact with plant shoots. All species studied exhibited stomata obliteration while T. hirta, in particular, presented early leaf abscission, changes in cellular relief, and organization and content of midrib cells. No significant ultrastructural alterations were detected under the experimental conditions studied. Indeed, mesophyll cells presented plastids with intact membrane systems. The high plant survival rates, together with mild morphoanatomic traits alterations in leaves, indicate that G. ulmifolia is more resistant to cement dust pollutant, followed by M. urundeuva and T. hirta. Thus, the three plant species are promising for being used to revegetate areas impacted by cement industries activities.

  14. Alternative Fuels in Cement Production

    DEFF Research Database (Denmark)

    Larsen, Morten Boberg

    The substitution of alternative for fossil fuels in cement production has increased significantly in the last decade. Of these new alternative fuels, solid state fuels presently account for the largest part, and in particular, meat and bone meal, plastics and tyre derived fuels (TDF) accounted...... for the most significant alternative fuel energy contributors in the German cement industry. Solid alternative fuels are typically high in volatile content and they may differ significantly in physical and chemical properties compared to traditional solid fossil fuels. From the process point of view......, considering a modern kiln system for cement production, the use of alternative fuels mainly influences 1) kiln process stability (may accelerate build up of blockages preventing gas and/or solids flow), 2) cement clinker quality, 3) emissions, and 4) decreased production capacity. Kiln process stability...

  15. Corrosion of metal containers containing cemented radioactive wastes

    International Nuclear Information System (INIS)

    Duffo, G.S.; Farina, S.B.; Schulz, F.M.; Marotta, F

    2010-01-01

    Nuclear activities generate different kinds of radioactive wastes. In the case of Argentina, wastes classified as low and medium level are conditioned in metal drums for final disposal in a repository whose design is based on the use of multiple and independent barriers. Nuclear energy plants generate a large volume of mid-level radioactive wastes, consisting mainly of ion-exchange resins contaminated by fission products. Other contaminated products such as gloves, papers, clothing, rubber and plastic tubing, can be incinerated and the ashes from the combustion also constitute wastes that must be disposed of. These wastes (resins and ashes) must be immobilized in order to avoid the release of radionuclides into the environment. The wastes usually undergo a process of cementing to immobilize them. This work aims to systematically study the process of degradation by corrosion of the steel drums in contact with the cemented resins and with the ashes cemented with the addition of different types and concentrations of aggressive compounds (chloride and sulfate). The specimens are configured so that the parameters of interest for the steel in contact with the cemented materials can be measured. The variables of corrosion potential, electric resistivity of the matrix and polarization resistance (PR) were monitored and show that the presence of chloride increases the susceptibility to corrosion of the drum steel that is in contact with the cement resin matrix

  16. Limestone calcined clay cement as a low-carbon solution to meet expanding cement demand in emerging economies

    Directory of Open Access Journals (Sweden)

    Yudiesky Cancio Díaz

    Full Text Available This paper aims at assessing the return on investment and carbon mitigation potentials of five investment alternatives for the Cuban cement industry in a long-term horizon appraisal (15 years. Anticipated growing demand for cement, constrained supply and an urgent need for optimisation of limited capital while preserving the environment, are background facts leading to the present study. This research explores the beneficial contribution of a new available technology, LC3 cement, resulting from the combination of clinker, calcined clay and limestone, with a capacity of replacing up to 50% of clinker in cement. Global Warming Potential (GWP is calculated with Life Cycle Assessment method and the economic investment's payback is assessed through Return on Capital Employed (ROCE approach. Main outcomes show that projected demand could be satisfied either by adding new cement plants—at a high environmental impact and unprofitable performance— or by introducing LC3 strategy. The latter choice allows boosting both the return on investment and the production capacity while reducing greenhouse gas (GHG emissions up to 20–23% compared to business-as-usual practice. Overall profitability for the industry is estimated to overcome BAU scenario by 8–10% points by 2025, if LC3 were adopted. Increasing the production of conventional blended cements instead brings only marginal economic benefits without supporting the needed increase in production capacity. The conducted study also shows that, in spite of the extra capital cost required for the calcination of kaolinite clay, LC3 drops production costs in the range of 15–25% compared to conventional solutions. Keywords: Cement, Alternative, ROCE, CO2, LCA, Investment

  17. Calcium Aluminate Cement Hydration Model

    Directory of Open Access Journals (Sweden)

    Matusinović, T.

    2011-01-01

    Full Text Available Calcium aluminate cement (AC is a very versatile special cement used for specific applications. As the hydration of AC is highly temperature dependent, yielding structurally different hydration products that continuously alter material properties, a good knowledge of thermal properties at early stages of hydration is essential. The kinetics of AC hydration is a complex process and the use of single mechanisms models cannot describe the rate of hydration during the whole stage.This paper examines the influence of temperature (ϑ=5–20 °C and water-to-cement mass ratio (mH /mAC = 0.4; 0.5 and 1.0 on hydration of commercial iron-rich AC ISTRA 40 (producer: Istra Cement, Pula, Croatia, which is a part of CALUCEM group, Figs 1–3. The flow rate of heat generation of cement pastes as a result of the hydration reactions was measured with differential microcalorimeter. Chemically bonded water in the hydrated cement samples was determined by thermo-gravimetry.Far less heat is liberated when cement and water come in contact for the first time, Fig. 1, than in the case for portland cement (PC. Higher water-to-cement ratio increases the heat evolved at later ages (Fig. 3 due to higher quantity of water available for hydration. A significant effect of the water-to-cement ratio on the hydration rate and hydration degree showed the importance of water as being the limiting reactant that slows down the reaction early. A simplified stoichiometric model of early age AC hydration (eq. (8 based on reaction schemes of principal minerals, nominally CA, C12A7 and C4AF (Table 1, was employed. Hydration kinetics after the induction period (ϑ < 20 °C had been successfully described (Fig. 4 and Table 2 by a proposed model (eq. (23 which simultaneously comprised three main mechanisms: nucleation and growth, interaction at phase boundary, and mass transfer. In the proposed kinetic model the nucleation and growth is proportional to the amount of reacted minerals (eq

  18. Rheological measurements on cement grouts

    International Nuclear Information System (INIS)

    Dalton, M.J.

    1986-06-01

    This report describes the techniques which have been developed at Winfrith for assessing the rheological properties of cement grouts. A discussion of the theory of rheology and its application to cement is given and the methodology for calibrating a special paddle measuring system for a commercial viscometer is described. The use of the system for determining flow curves, equilibrium viscosity, viscosity as a function of shearing time and structure changes is also discussed. (author)

  19. Cement pulmonary embolism after vertebroplasty.

    Science.gov (United States)

    Sifuentes Giraldo, Walter Alberto; Lamúa Riazuelo, José Ramón; Gallego Rivera, José Ignacio; Vázquez Díaz, Mónica

    2013-01-01

    In recent years, the use of vertebral cementing techniques for vertebroplasty and kyphoplasty has spread for the treatment of pain associated with osteoporotic vertebral compression fractures. This is also associated with the increased incidence of complications related with these procedures, the most frequent being originated by leakage of cementation material. Cement can escape into the vertebral venous system and reach the pulmonary circulation through the azygous system and cava vein, producing a cement embolism. This is a frequent complication, occurring in up to 26% of patients undergoing vertebroplasty but, since most patients have no clinical or hemodynamical repercussion, this event usually goes unnoticed. However, some serious, and even fatal cases, have been reported. We report the case of a 74-year-old male patient who underwent vertebroplasty for persistent pain associated with osteoporotic L3 vertebral fracture and who developed a cement leak into the cava vein and right pulmonary artery during the procedure. Although he developed a pulmonary cement embolism, the patient remained asymptomatic and did not present complications during follow-up. Copyright © 2012 Elsevier España, S.L. All rights reserved.

  20. Calcium Orthophosphate Cements and Concretes

    Directory of Open Access Journals (Sweden)

    Sergey V. Dorozhkin

    2009-03-01

    Full Text Available In early 1980s, researchers discovered self-setting calcium orthophosphate cements, which are a bioactive and biodegradable grafting material in the form of a powder and a liquid. Both phases form after mixing a viscous paste that after being implanted, sets and hardens within the body as either a non-stoichiometric calcium deficient hydroxyapatite (CDHA or brushite, sometimes blended with unreacted particles and other phases. As both CDHA and brushite are remarkably biocompartible and bioresorbable (therefore, in vivo they can be replaced with newly forming bone, calcium orthophosphate cements represent a good correction technique for non-weight-bearing bone fractures or defects and appear to be very promising materials for bone grafting applications. Besides, these cements possess an excellent osteoconductivity, molding capabilities and easy manipulation. Furthermore, reinforced cement formulations are available, which in a certain sense might be described as calcium orthophosphate concretes. The concepts established by calcium orthophosphate cement pioneers in the early 1980s were used as a platform to initiate a new generation of bone substitute materials for commercialization. Since then, advances have been made in the composition, performance and manufacturing; several beneficial formulations have already been introduced as a result. Many other compositions are in experimental stages. In this review, an insight into calcium orthophosphate cements and concretes, as excellent biomaterials suitable for both dental and bone grafting application, has been provided.

  1. Imaging of Flames in Cement Kilns To Study the Influence of Different Fuel Types

    DEFF Research Database (Denmark)

    Pedersen, Morten Nedergaard; Nielsen, Mads; Clausen, Sønnik

    2017-01-01

    The cement industry aims to use an increased amount of alternative fuels to reduce production costs and CO2 emissions. In this study three cement plants firing different kinds and percentages of alternative fuel were studied. A specially developed camera setup was used to monitor the flames...... in the three cement kilns and assess the effect of alternative fuels on the flame. It was found that cofiring with solid recovered fuel (SRF) would delay the ignition point by about 2 m and lower the intensity and temperature of the kiln flame compared to a fossil fuel flame. This is related to a larger...... particle size and moisture content of the alternative fuels, which lowers the conversion rate compared to fossil fuels. The consequences can be a lower kiln temperature and cement quality. The longer conversion time may also lead to the possibility of localized reducing conditions in the cement kiln, which...

  2. Estonia teater - helikindel ja sinine = Estonian National Opera - soundproof and blue / Urmas Oja

    Index Scriptorium Estoniae

    Oja, Urmas, 1981-2012

    2006-01-01

    Rahvusooperi Estonia maja teatritiiva interjööri renoveerimine. Sisekujundus: Juta Lember (kavandas ka uued valgustid), Aulo Padar (SAB Lember & Padar). Arhitekt Indrek Suigusaar (AB Pluss OÜ). Restaureerimistööd: KAR-Grupp. Projekt ja valmis 2005. Ill.: 8 värv. sisevaadet

  3. Increasing ethnic differences in mortality in Estonia after the collapse of the Soviet Union

    NARCIS (Netherlands)

    Leinsalu, Mall; Vågerö, Denny; Kunst, Anton E.

    2004-01-01

    STUDY OBJECTIVE: This study examined the change in ethnic differences in mortality in Estonia 1989-2000. DESIGN: Two unlinked cross sectional census based analyses were compared. Total and cause specific mortality was analysed for ethnic Estonians and Russians. The absolute differences in mortality

  4. Between Consumerism and Protectionism: Attitudes towards Children, Consumption and the Media in Estonia

    Science.gov (United States)

    Keller, Margit; Kalmus, Veronika

    2009-01-01

    This study measures attitudes towards children's vulnerability or empowerment within consumer culture, based on data from a representative population survey (N = 1475) conducted in Estonia in 2005. The study use indices comprised of assessments of consumption practices and assertions pertaining to the "endangered vs empowered child"…

  5. Film Estonia katastroofist jääb tegelikkusest kaugele / Kristjan Jaak Kangur

    Index Scriptorium Estoniae

    Kangur, Kristjan Jaak

    2001-01-01

    Kavandatavast katastroofifilmist "Baltic Storm", mis on ajendatud väidetest, et parvlaev "Estonia" uputati. Stsenaristiks on saksa teleajakirjanik Jutta Rabe, kes koos advokaat Kaj Holmbergiga lõi selleks puhuks stuudio Top Story. Peaosalisi mängivad Greta Scacchi (41) ja Jürgen Prochnow (60)

  6. Estonia huku filmi eesmärk : alustada tuleb uut uurimist / Tarmo Michelson

    Index Scriptorium Estoniae

    Michelson, Tarmo, 1975-

    2002-01-01

    Saksamaa toimuvad poliitilise põnevusfilmi "Baltic Storm" võtted. Film mis kujutab parvlaev "Estonia" hukku venelaste vandenõu tulemusena. Produtsendid on Jutta Rabe ja Kaj Holmberg, režissöör Reuben Leder, peaosades Greta Scacchi ja Jürgen Prochnow. Filmivõtetest räägib assistent Helje Kaskel

  7. Galeriiühendus Eesti Panga kvartalisse = Connecting Gallery to the Bank of Estonia Block

    Index Scriptorium Estoniae

    2003-01-01

    2003. a. veebruaris toimunud kutsutud arhitektuurikonkursi, mille eesmärgiks oli parandada Eesti Panga kvartali funktsionaalsust Estonia puiestee ja Sakala tänava poolsete osade vahel, töö. Projekterija: AB Urban Mark OÜ. Autorid: Ülar Mark, Kaja Pae. Konstruktsioonid: Inseneribüroo Peipman OÜ

  8. When Public Acts Like Private: The Failure of Estonia's School Choice Mechanism

    Science.gov (United States)

    Poder, Kaire; Lauri, Triin

    2014-01-01

    This article aims to show the segregating effect of the market-like matching of students and schools at the basic school level. The natural experiment case is Tallinn, the capital of Estonia. The current school choice mechanism applied in this case is based on entrance tests. There are increasingly over-subscribed intra-catchment area public…

  9. When Language becomes Power: Russian-Speaking Teachers in the Bilingual General Education System in Estonia

    Science.gov (United States)

    Kiilo, Tatjana; Kutsar, Dagmar

    2012-01-01

    After the re-establishment of independent Estonian statehood in 1991, Russian lost its privileges as the dominant and official language in Estonia, and Estonian continued as the only official language. This paper attempts to map the position of a Russian-speaking teacher within the sociological categories of power and language, based on the…

  10. Welcome to Estonia märk on kaotanud oma sära / Kadi Heinsalu

    Index Scriptorium Estoniae

    Heinsalu, Kadi, 1966-

    2004-01-01

    Ettevõtluse Arendamise Sihtasutus loodab parandada Welcome to Estonia märgi mainet. Märki kasutavad ettevõtjad ei näe märgist olulist kasu toodete müügil. Kommenteerivad Evelin Int-Lambot, Leena Murd ja Olaf Merisalu

  11. Climatic trends in Estonia during the period of instrumental observations and climate scenarios

    International Nuclear Information System (INIS)

    Jaagus, J.

    1996-01-01

    Weather conditions in Estonia are quite variable. Long-term periodical fluctuations have been observed in meteorological values. At the same time, the climate change during the last 100-150 years is marked. As a general tendency, the climate has become more maritime. Air pressure is characterized by an increasing trend in spring and summer, and by a decreasing trend in autumn and winter. Mean air temperature has increased, particularly over the colder half of the year. Precipitation area totals have risen, most of all in autumn and winter. Snow cover duration has decreased significantly. General circulation model-based climate change scenarios expect a general increase in air temperature in Estonia with warming in winter more significant than that in summer. Moreover, they indicate an increase in precipitation, but the results of the individual models are quite variable. The transient scenario shows that the main increase in precipitation will not occur during next decades, but only at the end of the transient period, around 2070. It can be stated that observed tendencies of climate change in Estonia concur with expected changes caused by global warming. According to the long-term fluctuations of meteorological values in Estonia, changes different from general trends can take place during the next decade. An increase in mean air pressure, sunshine duration and snow cover duration, as well as a decrease in mean air temperature and precipitation is expected in the following years

  12. University Studies as a Side Job: Causes and Consequences of Massive Student Employment in Estonia

    Science.gov (United States)

    Beerkens, Maarja; Magi, Eve; Lill, Liis

    2011-01-01

    Student employment is increasingly common in many countries. Compared to earlier decades, not only more students work but they also work longer hours. Among European countries Estonia is one of the clear "leaders" in student employment. This study uses survey data from 2,496 students in Estonian public and private universities to examine…

  13. Restrictions to Pharmacy Ownership and Vertical Integration in Estonia-Perception of Different Stakeholders.

    Science.gov (United States)

    Gross, Marit; Volmer, Daisy

    2016-04-19

    From 2020, the ownership of community pharmacies in Estonia will be limited to the pharmacy profession, and the vertical integration of wholesale companies and community pharmacies will not be allowed. The aim of this study was to evaluate the perception of different stakeholders in primary healthcare toward the new regulations of the community pharmacy sector in Estonia. A qualitative electronic survey was distributed to the main stakeholders in primary healthcare and higher education institutions providing pharmacy education ( n = 40) in May 2015. For data analysis, the systematic text condensation method was used. The study participants described two opposing positions regarding the development of community pharmacies in the future. Reform supporters emphasized increased professional independence and more healthcare-oriented operation of community pharmacies. Reform opponents argued against these ideas as community pharmacists do not have sufficient practical experience and finances to ensure sustainable development of the community pharmacy sector in Estonia. Based on the current perception of all respondents, the future operation of the community pharmacy sector in Estonia is unclear and there is urgent need for implementation criteria for the new regulations.

  14. The recertification of the professional accounting qualification in Estonia: the requirements and quality of CPD

    Directory of Open Access Journals (Sweden)

    Kaidi Kallaste

    2017-09-01

    Full Text Available The recertification of the professional accounting qualification in Estonia: the requirements and quality of CPD As the purpose of a professional qualification should be to ensure quality to employers/customers, appro-priate requirements for professional training should not be too low. On the other hand, too high require-ments for the amount of training would lead to the situation where maintaining the level is expensive and if the labour market does not consider having a professional certificate necessary, recertification will be discarded. The purpose of the research was to identify the factors that influence an accountant’s decision whether to recertify his/her professional qualification or not. The conditions of recertification were ana-lysed and compared to other countries as were the requirements set up for auditors. The results of the survey revealed that in Estonia the decision not to recertify one’s professional qualification was mainly due to not having fulfilled the required number of qualification hours or not having certificates proving one’s participation in qualification training sessions. At the same time, compared to other countries, the requirements in Estonia are very low. So that the increase in the amount of training would not hinder recertification, alternative solutions for Estonia are proposed in the article.

  15. Toxoplasma gondii seroprevalence in free-ranging moose (Alces alces) hunted for human consumption in Estonia

    DEFF Research Database (Denmark)

    Remes, Noora; Kärssin, Age; Must, Kärt

    2018-01-01

    In Estonia, northeastern Europe, antibodies against Toxoplasma gondii are common in many host species, including wildlife, domestic animals, and humans. Our nationwide study aimed to estimate T. gondii seroprevalence and its geographical distribution, and to evaluate plausible risk factors for se...

  16. Estonia vormelitel täitus juba pool sajandit / Tõnu Ojala

    Index Scriptorium Estoniae

    Ojala, Tõnu, 1969-

    2008-01-01

    November tehnika ajaloos: 50 aastat möödus Estonia-1 esimesest võistlusstardist Leningradis Nevski ringrajal. 85 aastat tagasi sai Jacob Schick patendi elektrilisele habemeajamismasinale. 60 aastat tagasi konstrueeris Auguste Piccard batüskaafi. 10 aastat tagasi sai 77aastasest USA senaatorist John Glennist maailma vanim astronaut

  17. Education Policy as Normative Discourse and Negotiated Meanings: Engaging the Holocaust in Estonia

    Science.gov (United States)

    Stevick, E. Doyle

    2010-01-01

    This article uses a socio-cultural approach to analyze the formation and implementation of Estonia's Holocaust Day Policy, a day of both commemoration for victims of the Holocaust and other crimes against humanity, and education about the Holocaust. It investigates both the multi-level development of the policy in light of external pressure (from…

  18. Learning and Developing as a University Teacher: Narratives of Early Career Academics in Estonia

    Science.gov (United States)

    Remmik, Marvi; Karm, Mari; Lepp, Liina

    2013-01-01

    In recent years the higher education context in Estonia, as in most European countries, has changed a lot. All changes have an impact on university teachers' practice and their work organisation, and are presenting new challenges. The current research aims at developing an understanding of Estonian early career academics' professional identity by…

  19. Digoxin: use pattern in Estonia and bioavailability of the local market leader.

    Science.gov (United States)

    Pähkla, R; Irs, A; Oselin, K; Rootslane, L

    1999-10-01

    In comparison with neighbouring Scandinavian countries, the use of digoxin in Estonia is high. The present study was carried out to determine the use pattern of digoxin in Estonia and bioavailability of the local market leader preparation in comparison with Lanoxin. Drug use data were evaluated from the annual reports of wholesale companies. For the bioequivalence study, a single-blind cross-over randomised two-way single-dose comparative bioavailability study was performed using 14 healthy volunteers. Digoxin concentrations in serum samples and urine were measured by chemiluminescent competitive immunoassay. The use of digoxin in Estonia has increased by 35% during the period 1994-97. The steady market leader was the local generic drug. No statistically significant differences were found in any pharmacokinetic parameter between the generic preparation and Lanoxin. All parameters showed considerable variability. The total amount of drug excreted was the parameter with lowest inter- individual variation. The present study indicates that the generic digoxin preparation studied is bioequivalent to Lanoxin. The increasing use of digoxin in Estonia is not caused by low bioavailability of the local market leader but by therapeutic traditions.

  20. Prevalence of Long-Chain 3-Hydroxyacyl-CoA Dehydrogenase Deficiency in Estonia

    DEFF Research Database (Denmark)

    Joost, K; Ounap, K; Zordania, R

    2012-01-01

    The aim of our study was to evaluate the prevalence of long chain 3-hydroxyacyl-CoA dehydrogenase deficiency (LCHADD) in the general Estonian population and among patients with symptoms suggestive of fatty acid oxidation (FAO) defects. We collected DNA from a cohort of 1,040 anonymous newborn blo...... prevalence of LCHADD in Estonia would be 1: 91,700....

  1. [Johan Eellend. Cultivating the Rural Citizen : Modernity, Agrarianism and Citizenship in Late Tsarist Estonia] / Kersti Lust

    Index Scriptorium Estoniae

    Lust, Kersti, 1976-

    2008-01-01

    Arvustus: Eellend, Johan. Cultivating the Rural Citizien : Modernity, Agrarianism and Citizenship in Late Tsarist Estonia. Stockholm : Stockholm Universty, 2007. Eesti agraarideoloogia kujunemist ja olemust käsitlevast dissertatsioonist. Tegemist on Eesti ühiskondliku mõtte voolude ja nende mõjuulatuse tavapärasest erineva nägemusega

  2. Costs, health effects and cost-effectiveness of alcohol and tobacco control strategies in Estonia.

    NARCIS (Netherlands)

    Lai, T.; Habicht, J.; Reinap, M.; Chisholm, D.; Baltussen, R.M.P.M.

    2007-01-01

    OBJECTIVE: To assess the population-level costs, effects and cost-effectiveness of different alcohol and tobacco control strategies in Estonia. DESIGN: A WHO cost-effectiveness modelling framework was used to estimate the total costs and effects of interventions. Costs were assessed in Estonian

  3. Low pH Cements

    International Nuclear Information System (INIS)

    Savage, David; Benbow, Steven

    2007-05-01

    The development of low-pH cements for use in geological repositories for radioactive waste stems from concerns over the potential for deleterious effects upon the host rock and other EBS materials (notably bentonite) under the hyperalkaline conditions (pH > 12) of cement pore fluids. Low pH cement (also known as low heat cement) was developed by the cement industry for use where large masses of cement (e.g. dams) could cause problems regarding heat generated during curing. In low pH cements, the amount of cement is reduced by substitution of materials such as fly ash, blast furnace slag, silica fume, and/or non-pozzolanic silica flour. SKB and Posiva have ruled out the use of blast furnace slag and fly-ash and are focusing on silica fume as a blending agent. Currently, no preferred composition has been identified by these agencies. SKB and Posiva have defined a pH limit ≤ 11 for cement grout leachates. To attain this pH, blending agents must comprise at least 50 wt % of dry materials. Because low pH cement has little, or no free portlandite, the cement consists predominantly of calcium silicate hydrate (CSH) gel with a Ca/Si ratio ≤ 0.8. Although there are potential implications for the performance of the spent fuel and cladding due to the presence of hyperalkaline fluids from cement, the principal focus for safety assessment lies with the behaviour of bentonite. There are a number of potential constraints on the interaction of hyperalkaline cement pore fluids with bentonite, including mass balance, thermodynamic issues, mass transport, and kinetics, but none of these is likely to be limiting if conventional OPC cements are employed in repository construction. Nevertheless: Low-pH cements may supply approximately 50 % less hydroxyl ions than conventional OPC for a given volume of cement, but mass balance constraints are complicated by the uncertainty concerning the type of secondary minerals produced during cement-bentonite interaction. The change of aqueous

  4. Low pH Cements

    Energy Technology Data Exchange (ETDEWEB)

    Savage, David; Benbow, Steven [Quintessa Ltd., Henley-on-Thames (United Kingdom)

    2007-05-15

    The development of low-pH cements for use in geological repositories for radioactive waste stems from concerns over the potential for deleterious effects upon the host rock and other EBS materials (notably bentonite) under the hyperalkaline conditions (pH > 12) of cement pore fluids. Low pH cement (also known as low heat cement) was developed by the cement industry for use where large masses of cement (e.g. dams) could cause problems regarding heat generated during curing. In low pH cements, the amount of cement is reduced by substitution of materials such as fly ash, blast furnace slag, silica fume, and/or non-pozzolanic silica flour. SKB and Posiva have ruled out the use of blast furnace slag and fly-ash and are focusing on silica fume as a blending agent. Currently, no preferred composition has been identified by these agencies. SKB and Posiva have defined a pH limit {<=} 11 for cement grout leachates. To attain this pH, blending agents must comprise at least 50 wt % of dry materials. Because low pH cement has little, or no free portlandite, the cement consists predominantly of calcium silicate hydrate (CSH) gel with a Ca/Si ratio {<=} 0.8. Although there are potential implications for the performance of the spent fuel and cladding due to the presence of hyperalkaline fluids from cement, the principal focus for safety assessment lies with the behaviour of bentonite. There are a number of potential constraints on the interaction of hyperalkaline cement pore fluids with bentonite, including mass balance, thermodynamic issues, mass transport, and kinetics, but none of these is likely to be limiting if conventional OPC cements are employed in repository construction. Nevertheless: Low-pH cements may supply approximately 50 % less hydroxyl ions than conventional OPC for a given volume of cement, but mass balance constraints are complicated by the uncertainty concerning the type of secondary minerals produced during cement-bentonite interaction. The change of aqueous

  5. Development of cement material using inorganic additives

    International Nuclear Information System (INIS)

    Toyohara, Masumitsu; Satou, Tatsuaki; Wada, Mikio; Ishii, Tomoharu; Matsuo, Kazuaki.

    1997-01-01

    Inorganic admixtures to enhance the fluidity of cement material was developed. These admixtures turned into easy to immobilize the miscellaneous radioactive waste using cement material. It was found that the ζ potential of cement particles was directly proportional to the content of the inorganic admixtures in cement paste and the particles of cement were dispersed at the high ζ potential. The condensed sodium phosphate, which was the main component of the inorganic admixtures, retarded the dissolution of Ca 2+ ion from the cement, and generated the colloids by incorporating dissolved Ca 2+ ion. The cement material containing the inorganic admixtures was found to have the same mechanical strength and adsorption potential of radionuclides in comparison to normal cement materials. It was confirmed that the cement material containing the inorganic admixture was effectively filled gaps of miscellaneous radioactive waste. (author)

  6. Development of high-performance blended cements

    Science.gov (United States)

    Wu, Zichao

    2000-10-01

    This thesis presents the development of high-performance blended cements from industrial by-products. To overcome the low-early strength of blended cements, several chemicals were studied as the activators for cement hydration. Sodium sulfate was discovered as the best activator. The blending proportions were optimized by Taguchi experimental design. The optimized blended cements containing up to 80% fly ash performed better than Type I cement in strength development and durability. Maintaining a constant cement content, concrete produced from the optimized blended cements had equal or higher strength and higher durability than that produced from Type I cement alone. The key for the activation mechanism was the reaction between added SO4 2- and Ca2+ dissolved from cement hydration products.

  7. Energy efficiency improvement potentials for the cement industry in Ethiopia

    International Nuclear Information System (INIS)

    Tesema, Gudise; Worrell, Ernst

    2015-01-01

    The cement sector is one of the fast growing economic sectors in Ethiopia. In 2010, it consumed 7 PJ of primary energy. We evaluate the potential for energy savings and CO_2 emission reductions. We start by benchmarking the energy performance of 8 operating plants in 2010, and 12 plants under construction. The benchmarking shows that the energy intensity of local cement facilities is high, when compared to the international best practice, indicating a significant potential for energy efficiency improvement. The average electricity intensity and fuel intensity of the operating plants is 34% and 36% higher. For plants under construction, electricity use is 36% and fuel use 27% higher. We identified 26 energy efficiency measures. By constructing energy conservation supply curves, the energy-efficiency improvement potential is assessed. For the 8 operating plants in 2010, the cost-effective energy savings equal 11 GWh electricity and 1.2 PJ fuel, resulting in 0.1 Mt CO_2 emissions reduction. For the 20 cement plants expected to be in operation by 2020, the cost-effective energy saving potentials is 159 GWh for electricity and 7.2 PJ for fuel, reducing CO_2 emissions by about 0.6 Mt. We discuss key barriers and recommendations to realize energy savings. - Highlights: • The cement sector in Ethiopia is growing rapidly, using mainly imported fuels. • Benchmarking demonstrates a significant potential for energy efficiency improvement. • A large part of the energy efficiency potential can be achieved cost-effectively. • Ethiopia should ban the construction of obsolete vertical shaft kilns.

  8. Utilization of small-angle neutron scattering to decide the maximum loading of nuclear waste in cement matrix

    International Nuclear Information System (INIS)

    Das, Avik; Mazumder, S.; Sen, D.; Yalmali, V.; Shah, J.G.

    2014-01-01

    Nuclear power plants generate many kinds of hazardous nuclear waste which are needed to be disposed in an eco-friendly manner. Many different waste incarceration techniques have been adapted for managing the nuclear waste of different category of radioactivity. Immobilisation of low and intermediate level radioactive wastes in cement matrix is one of the widely used and cost-effective techniques in waste management. However, loading of nuclear waste in cement matrix can alter the mesoscopic structure of the hydrated cement and hence, it is very important to set the maximum limit of waste loading in cement for providing proper physical isolation to the nuclear waste

  9. Technical-economic parameters of the new oil shale mining-chemical complex in Northeast Estonia

    International Nuclear Information System (INIS)

    Kuzmiv, I.; Fraiman, J.

    2006-01-01

    The history of oil shale mining in Estonia has reached its century mark. Three oil shale branches have been formed and have been working on the basis of Estonian oil shale deposits: the mining industry (underground and surface extraction), the power industry (heat and electric energy generation), and the chemical industry (gas and synthetic oils). The authors attempted to summarize the experience of the activities of these branches and to make into a whole the results of their research developments in the past years, as well as to form a notion about perspectives of oil shale in Estonia. Variants of the mining-chemical oil shale complex production and trade patterns differed from used ones. Mining methods, thermal processing of oil shale, and solid, liquid, and gas waste recovery have been studied, analyzed, and worked out up to the present. Setting up a flexible trade structure within the framework of that complex is considered the main economic mechanism capable of balancing production costs of such a complex with its earnings, which could respond properly to any, even peak, fluctuations of the market for final products processed from oil shale. Data of the working 'Estonia' oil shale mine were used as the basis of the analysis and practical conclusions. Information on the mine being projected in the region of Ojamaa in the northeast of Estonia was taken as the data of the worthwhile supplier. Oil shale processing chemical complex is considered in two structural alternatives: in technological chain with the 'Estonia' mine (the first variant), and the projected mine of a new technical level (the second variant). (author)

  10. Use of a generic protocol in documentation of prescription errors in Estonia, Norway and Sweden

    Directory of Open Access Journals (Sweden)

    Haavik S

    2012-06-01

    Full Text Available Pharmacists have an important role in detecting, preventing, and solving prescription problems, which if left unresolved, may pose a risk of harming the patient.Objective: The objectives of this study were to evaluate the feasibility of a generic study instrument for documentation of prescription problems requiring contact with prescriber before dispensing. The study was organized: 1 by countries: Estonia, Norway and Sweden; 2 by type of prescriptions: handwritten prescriptions, printouts of prescriptions in the electronic medical record and electronically transmitted prescriptions to pharmacies; and 3 by recording method - self-completion by pharmacists and independent observers.Methods: Observational study with independent observers at community pharmacies in Estonia (n=4 and Sweden (n=7 and self-completed protocols in Norway (n=9.Results: Pharmacists’ in Estonia contacted the prescriber for 1.47% of the prescriptions, about 3 times as often as in Norway (0.45% and Sweden (0.38%. Handwritten prescriptions dominated among the problem prescriptions in Estonia (73.2%, printouts of prescriptions in the electronic medical record (89.1% in Norway and electronically transmitted prescriptions to pharmacies (55.9% in Sweden.More administrative errors were identified on handwritten prescriptions and printouts of prescriptions in the electronic medical record in Estonia and in Norway compared with electronically transmitted prescriptions to pharmacies in Sweden (p<0.05 for prescription types and p<0.01 for countries. However, clinically important errors and delivery problems appeared equally often on the different types of prescriptions. In all three countries, only few cases of drug interactions and adverse drug reactions were identified.Conclusion: Despite the different patterns of prescription problems in three countries, the instrument was feasible and can be regarded appropriate to document and classify prescription problems necessitating contact

  11. Influence of Blended Cements with Calcareous Fly Ash on Chloride Ion Migration and Carbonation Resistance of Concrete for Durable Structures.

    Science.gov (United States)

    Glinicki, Michał A; Jóźwiak-Niedźwiedzka, Daria; Gibas, Karolina; Dąbrowski, Mariusz

    2016-01-02

    The objective of this paper is to examine the possible use of new blended cements containing calcareous fly ash in structural concrete, potentially adequate for structural elements of nuclear power plants. The investigation included five new cements made with different contents of non-clinker constituents: calcareous fly ash, siliceous fly ash, ground granulated blastfurnace slag, and a reference cement-ordinary Portland cement. The influence of innovative cements on the resistance of concrete to chloride and carbonation exposure was studied. Additionally, an evaluation of the microstructure was performed using optical microscopy on concrete thin sections. Test results revealed a substantial improvement of the resistance to chloride ion penetration into concrete containing blended cements. The resistance was higher for increased clinker replacement levels and increased with curing time. However, concrete made with blended cements exhibited higher depth of carbonation than the Portland cement concrete, except the Portland-fly ash cement with 14.3% of calcareous fly ash. The thin sections analysis confirmed the values of the carbonation depth obtained from the phenolphthalein test. Test results indicate the possible range of application for new cements containing calcareous fly ash.

  12. Development of low-activation design method for reduction of radioactive waste (4). Development of low-activation cement

    International Nuclear Information System (INIS)

    Ichitsubo, Koki; Tanosaki, Takao; Miura, Keiichi; Tomotake, Hiroichi; Yamada, Kazunori; Fujita, Hideki; Kinno, Masaharu; Hasegawa, Akira

    2008-01-01

    When nuclear plants will reach to decommission stage, a huge amount of concrete should be disposed as radioactive waste. To reduce the amount of radioactive concrete, the most effective methodology is not to use the materials of high radionuclide content such as coal ash and blast furnace slag, and to use limestone as additives or aggregate. However, concrete uses Portland cement for hardening, therefore, it is difficult to reduce the amount of radioactive concrete unless radionuclide content in cement is reduced. So in this study, we tried to develop the new type of Low-activation cement by reducing of radionuclide as europium and cobalt. As a result, we could reduce the amount of europium and cobalt in cement significantly, and obtained the result that the new cements can reduce radioactivity to one-third or less against commercially Portland cement in Japan. (author)

  13. Evaluation of ternary blended cements for use in transportation concrete structures

    Science.gov (United States)

    Gilliland, Amanda Louise

    This thesis investigates the use of ternary blended cement concrete mixtures for transportation structures. The study documents technical properties of three concrete mixtures used in federally funded transportation projects in Utah, Kansas, and Michigan that used ternary blended cement concrete mixtures. Data were also collected from laboratory trial batches of ternary blended cement concrete mixtures with mixture designs similar to those of the field projects. The study presents the technical, economic, and environmental advantages of ternary blended cement mixtures. Different barriers of implementation for using ternary blended cement concrete mixtures in transportation projects are addressed. It was concluded that there are no technical, economic, or environmental barriers that exist when using most ternary blended cement concrete mixtures. The technical performance of the ternary blended concrete mixtures that were studied was always better than ordinary portland cement concrete mixtures. The ternary blended cements showed increased durability against chloride ion penetration, alkali silica reaction, and reaction to sulfates. These blends also had less linear shrinkage than ordinary portland cement concrete and met all strength requirements. The increased durability would likely reduce life cycle costs associated with concrete pavement and concrete bridge decks. The initial cost of ternary mixtures can be higher or lower than ordinary portland cement, depending on the supplementary cementitious materials used. Ternary blended cement concrete mixtures produce less carbon dioxide emissions than ordinary portland cement mixtures. This reduces the carbon footprint of construction projects. The barriers associated with implementing ternary blended cement concrete for transportation projects are not significant. Supplying fly ash returns any investment costs for the ready mix plant, including silos and other associated equipment. State specifications can make

  14. Armastus kui vale(m) : Mari Vihmandi ooperi "Armastuse valem" lavastusest Estonias / Ester Võsu ja Kristel Pappel

    Index Scriptorium Estoniae

    Võsu, Ester, 1975-

    2009-01-01

    Argentiina kirjaniku Esther Vilari romaani "Nina Glucksteini matemaatika" ainetel valminud Mari Vihmandi ooperist "Armastuse valem", libreto Maimu Berg, lavastaja Liis Kolle, tantsu- ja liikumisseaded Ana Mondini. Esietendus 17. oktoobril 2008 Rahvusooperis Estonia

  15. [Anu Mai Kõll. The village and the class war : anti-kulak campaign in Estonia] / Karsten Brüggemann

    Index Scriptorium Estoniae

    Brüggemann, Karsten, 1965-

    2015-01-01

    Arvustus: Kõll, Anu Mai. The village and the class war : anti-kulak campaign in Estonia (Historical studies in Eastern Europe and Eurasia, 2). Central European University Press. Budapest and New York 2013

  16. Master plan study - District heating Kohtla-Jaerve and Johvi municipalities. Estonia. Final report. Appendices for chapter 7

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The appendices to chapter 7 of the master plan study on district heating in the municipalities of Kohtla-Jarve and Johvi (Estonia) present technical data on production units, also with regard to new facilities. (ARW)

  17. [Sebastian Rimestad. The Challenges of Modernity to the Orthodox Church in Estonia and Latvia (1917-1940)]/ Svetlana Bogojavlenska

    Index Scriptorium Estoniae

    Bogojavlenska, Svetlana

    2014-01-01

    Arvustus: Sebastian Rimestad. The Challenges of Modernity to the Orthodox Church in Estonia and Latvia (1917-1940). (Erfurter Studien zur Kulturgeschichte des orthdoxen Christentums, Bd. 6). Lang, Frankfurt am Main u. a. 2012

  18. Seepage/Cement Interactions

    International Nuclear Information System (INIS)

    Carpenter, D.

    2000-01-01

    The Development Plan (CRWMS M andO 1999a) pertaining to this task defines the work scopes and objectives for development of various submodels for the Physical and Chemical Environment Abstraction Model for TSPA-LA. The Development Plan (CRWMS M andO 1999a) for this specific task establishes that an evaluation be performed of the chemical reactions between seepage that has entered the drift and concrete which might be used in the repository emplacement drifts. The Development Plan (CRWMS M andO 1999a) then states that the potential effects of these water/grout reactions on chemical conditions in the drift be assessed factoring in the influence of carbonation and the relatively small amount of grout. This task is also directed at: (1) developing a conceptualization of important cement/seepage interactions and potential impacts on EBS performance, (2) performing a screening analysis to assess the importance of cement/seepage interactions. As the work progresses and evolves on other studies, specifically the Engineered Barrier System: Physical and Chemical Environment (P andCE) Model (in progress), many of the issues associated with items 1 and 2, above, will be assessed. Such issues include: (1) Describing the mineralogy of the specified cementitious grout and its evolution over time. (2) Describing the composition of the water before contacting the grout. (3) Developing reasonable upper-bound estimates for the composition of water contacting grout, emphasizing pH and concentrations for anions such as sulfate. (4) Evaluating the equilibration of cement-influenced water with backfill and gas-phase CO 2 . (5) Developing reasonable-bound estimates for flow rate of affected water into the drift. The concept of estimating an ''upper-bound'' range for reaction between the grout and the seepage, particularly in terms of pH is based on equilibrium being established between the seepage and the grout. For example, this analysis can be based on equilibrium being established as

  19. Ühe (suure kultuurinarratiivi saatus: Noor-Eesti. The Fate of a (Great Cultural Narrative: Young-Estonia

    Directory of Open Access Journals (Sweden)

    Rein Veidemann

    2012-04-01

    Full Text Available This focus of this article is the fate of the cultural narrative that has most influenced Estonian culture of the 20th century – Young Estonia. The point of departure for the analysis is Tiit Hennoste’s 2005 essay ”Young Estonia – An Unfinished Project for Self-Colonization”, which I interpret as the interruption of Young Estonia’s ”great narrative”. Hennoste’s demythologizing approach should be regarded in the context of postmodernism (or of postcolonial treatments of literature and art. I argue that the fact that Young Estonia’s models for cultural movements were located in Europe did not automatically lead to the assimilation of 20th century Estonia (literary culture. Neither did they engage in an automatic copying of European culture; their activities might better be regarded as a process of intertexual enrichment. In what follows, the fate of the narrative of Young Estonia will be traced both in terms of the literary field of Soviet Estonia in the 1950s and 1960s, and in exile. I claim that renewed awareness of the narrative of Young Estonia can be traced to the publication of a collection of Gustav Suits’ Poems in 1959, edited and with an afterword by Endel Sõgel. If one lowers the volume on the vulgar Soviet ideologization in Sõgel’s text, key words that characterize the Young Estonia canon remain in place undisturbed: innovativeness, intellectual greatness, turning point, the social nature of art and literature, consonance of the aesthetic and the ethical. Sõgel’s framing of Young Estonia stands in contrast to its apologetic treatment in the postwar Estonian diaspora. On the one hand, this line of interpretation follows the basic outlines of a critical narrative that developed in the 1920s; on the other, since most of Young Estonia’s authors and followers among the Estonian literary elite had gone into exile in 1944, diaspora interpretations represent a definite literary-political position. In the 1960s a

  20. Effect of wastewater on properties of Portland pozzolana cement

    Science.gov (United States)

    Babu, G. Reddy

    2017-07-01

    This paper presents the effect of wastewaters on properties of Portland pozzolana cement (PPC). Fourteen water treatment plants were found out in the Narasaraopet municipality region in Guntur district, Andhra Pradesh, India. Approximately, from each plant, between 3500 and 4000 L/day of potable water is selling to consumers. All plants are extracting ground water and treating through Reverse Osmosis (RO) process. During water treatment, plants are discharging approximately 1,00,000 L/day as wastewater in side drains in Narasaraopet municipality. Physical and chemical analysis was carried out on fourteen plants wastewater and distilled water as per producer described in APHA. In the present work, based on the concentrations of constituent's in wastewater, four typical plants i.e., Narasaraopeta Engineering College (NECWW), Patan Khasim Charitable Trust (PKTWW), Mahmadh Khasim Charitable Trust (MKTWW) and Amara (ARWW) were considered. The performance of four plants wastewater on physical properties i.e., setting times, compressive strength, and flexural strength of Portland pozzolana Cement (PPC) were performed in laboratories and compared same with reference specimens i.e., made with Distilled Water (DW) as mixing water. No significant change was observed in initial and finial setting time but setting times of selected wastewaters were retarded as compared to that of reference water. Almost, no change was observed in 90 days compressive and flexural strengths in four plants wastewaters specimens compared to that of reference water specimens. XRD technique was employed to find out main hydration compounds formed in the process.

  1. A modified PMMA cement (Sub-cement) for accelerated fatigue testing of cemented implant constructs using cadaveric bone.

    Science.gov (United States)

    Race, Amos; Miller, Mark A; Mann, Kenneth A

    2008-10-20

    Pre-clinical screening of cemented implant systems could be improved by modeling the longer-term response of the implant/cement/bone construct to cyclic loading. We formulated bone cement with degraded fatigue fracture properties (Sub-cement) such that long-term fatigue could be simulated in short-term cadaver tests. Sub-cement was made by adding a chain-transfer agent to standard polymethylmethacrylate (PMMA) cement. This reduced the molecular weight of the inter-bead matrix without changing reaction-rate or handling characteristics. Static mechanical properties were approximately equivalent to normal cement. Over a physiologically reasonable range of stress-intensity factor, fatigue crack propagation rates for Sub-cement were higher by a factor of 25+/-19. When tested in a simplified 2 1/2-D physical model of a stem-cement-bone system, crack growth from the stem was accelerated by a factor of 100. Sub-cement accelerated both crack initiation and growth rate. Sub-cement is now being evaluated in full stem/cement/femur models.

  2. 76 FR 76760 - Gray Portland Cement and Cement Clinker From Japan

    Science.gov (United States)

    2011-12-08

    ... and Cement Clinker From Japan Determination On the basis of the record \\1\\ developed in the subject... duty order on gray Portland cement and cement clinker from Japan would be likely to lead to... and Cement Clinker from Japan: Investigation No. 731- TA-461 (Third Review). By order of the...

  3. Seating load parameters impact on dental ceramic reinforcement conferred by cementation with resin-cements.

    LENUS (Irish Health Repository)

    Addison, Owen

    2010-09-01

    Cementation of all-ceramic restorations with resin-cements has been demonstrated to reduce the incidence of fracture in service. The aim was to investigate the influence of loading force and loading duration applied during cementation on the reinforcement conferred by a resin-cement on a leucite reinforced glass-ceramic.

  4. The use of cement grouts for the immobilisation of solid radioactive waste

    International Nuclear Information System (INIS)

    Brown, D.J.; Smith, D.L.

    1982-06-01

    The use of cement grouts is being considered for the immobilisation of solid items of radioactive waste. In this report the factors which influence the selection of a grout for use in an active plant are identified. The properties and limitations of standard cement grouts are summarised. Inactive grouting trials carried out in the period September 1981 to June 1982 on the 220 dm 3 scale are described. (author)

  5. The use of teetaimed in Estonia, 1880s-1990s.

    Science.gov (United States)

    Sõukand, Renata; Kalle, Raivo

    2012-10-01

    This research contributes to a better understanding of the criteria used for the selection of plants for making beverages. Worldwide, not only the leaves of Camellia sinensis, but also various other plants are used for making tea. We argue that the selection of plants for making tea (in Estonian teetaimed) depends on specific features possessed by or attributed to the plants. 54 plant taxa and one lichen were identified as being used for making tea, based on the analysis of Estonian historical handwritten archival records on plant use for the period from 1887 to 1994. The influence of popular literature on the use of plants for making tea was also assessed. The suitability of a plant for making tea depends on a combination of factors like multifunctional use, mild taste and attributed medicinal properties. The variety of medicinal properties attributed to teetaimed in folk medicine allowed herbal tea drinking to be considered as mild disease prevention. Hence, the roots of the Estonian tea tradition lie in the medicinal use of the plants, not oriental ceremonial tea drinking. Copyright © 2012 Elsevier Ltd. All rights reserved.

  6. The effects of political and economic transitions on health and safety in Estonia: an Estonian-Swedish comparative study.

    Science.gov (United States)

    Kaasik, T; Andersson, R; Hörte, L G

    1998-11-01

    A general and dramatic deterioration of health in Estonia during the transition period 1990-1994 was analysed using Sweden as a comparative example. Though there were diverging trends between Estonia and Sweden in the leading cause of death, cardiovascular diseases, the gap in mortality from injury had increased most rapidly. While the injury mortality rate slightly decreased in Sweden from 1990 to 1994, it almost doubled in Estonia. In 1994, the total injury death rate for men was about 6 times higher in Estonia than in Sweden. The death rates for some types of injuries, such as alcohol intoxication and homicide, were many tenfolds higher in Estonia than in Sweden. Injury contributed the most to the widening health gap between the countries, especially in males. The mechanisms of this sudden health deterioration remain to be fully explained. It could be hypothesised that behind the traditional behavioural risk factors, the influence of socio-political factors related to economic and political reconstruction is present. A widespread risk-taking and unhealthy behaviour among Estonians can likely be partly explained as a way of coping with the distress created by the new demands of transition society. An important challenge on the way to improvement is creating the political will among policy-makers to confront the tremendous problems of controlling the factors in society that affect the population's health in Estonia.

  7. Cement radwaste solidification studies third annual report

    International Nuclear Information System (INIS)

    Brown, D.J.; James, J.M.; Lee, D.J.; Smith, D.L.; Walker, A.T.

    1982-03-01

    This report summarises cement radwaste studies carried out at AEE Winfrith during 1981 on the encapsulation of medium and low active waste in cement. During the year more emphasis has been placed on the work which is directly related to the solidification of SGHWR active sludge. Information has been obtained on the properties of 220 dm 3 drums of cemented waste. The use of cement grouts for the encapsulation of solid items has also been investigated during 1981. (U.K.)

  8. Characterization of cement-stabilized Cd wastes

    International Nuclear Information System (INIS)

    Maria Diez, J.; Madrid, J.; Macias, A.

    1996-01-01

    Portland cement affords both physical and chemical immobilization of cadmium. The immobilization has been studied analyzing the pore fluid of cement samples and characterizing the solid pastes by X-ray diffraction. The influence of cadmium on the cement hydration and on its mechanical properties has been also studied by isothermal conduction calorimetry and by the measure of strength and setting development. Finally, the effect of cement carbonation on the immobilization of cadmium has been analyzed

  9. Substantial global carbon uptake by cement carbonation

    OpenAIRE

    Xi, Fengming; Davis, Steven J.; Ciais, Philippe; Crawford-Brown, Douglas; Guan, Dabo; Pade, Claus; Shi, Tiemao; Syddall, Mark; Lv, Jie; Ji, Lanzhu; Bing, Longfei; Wang, Jiaoyue; Wei, Wei; Yang, Keun-Hyeok; Lagerblad, Björn

    2016-01-01

    Calcination of carbonate rocks during the manufacture of cement produced 5% of global CO2 emissions from all industrial process and fossil-fuel combustion in 20131, 2. Considerable attention has been paid to quantifying these industrial process emissions from cement production2, 3, but the natural reversal of the process—carbonation—has received little attention in carbon cycle studies. Here, we use new and existing data on cement materials during cement service life, demolition, and secondar...

  10. Situation analysis in relation to district heating and CHP in the Baltic Sea Region: Estonia, Latvia, Lithuania, Poland, Russia, Kaliningrad

    International Nuclear Information System (INIS)

    2000-11-01

    The situation analysis embraces chapters on: Estonia, Kaliningrad, Latvia, Lithuania, Poland and Russia, which experience varying degrees of difficulties with the transition to a market economy, and with integrating into the world market. In the following, the focus is on Lithuania, which has been visited during the project period. Lithuania has specific problems due to the existence of the Ignalina power plant, but has nevertheless characteristics, which apply to Estonia and Latvia as well. The problem with the quality of heat supply is rampant in all the countries, as is legal framework for the sector, except in Poland, which has generally attracted much attention from investors over the last ten years and has experienced a relatively sound political development in the energy sector. The main problem in all countries seem to relate to the policy development. The case of Lithuania confirms this. Following the observations on Lithuania, it is attempted to establish some points of concern, which are relevant to a greater or lesser extent in all countries, as well as some suggestions on how to move towards a solution of those problems. As mentioned Poland is generally in a better position, technically and politically than the three Baltic states, whereas Russia still needs to progress much on those issues. The general recommendations for initiatives in the Baltic countries in question are in brief: Establishing a clear view at governmental level of what the EU and liberalisation will bring, and what needs to be done additionally to secure main energy political objectives. Issues such as security of supply, environmental protection, low cost energy supplies and security of investments need to be thoroughly discussed at national level. It is important to understand that EU Directives provide a framework, not an answer to the future of the energy sector. Reinforcement of governmental bodies that deal with the practical problems of the energy sector. The main task of

  11. Cementation unit for radioactive wastes

    International Nuclear Information System (INIS)

    Dellamano, Jose Claudio; Vicente, Roberto; Lima, Jose Rodrigues de

    2001-01-01

    This communication describes the waste cementation process and facility developed at Instituto de Pesquisas Energeticas e Nucleares - IPEN. The process is based on 200 litres batch operation, in drum mixing, with continuous cement feeding. The equipment is a single recoverable helicoidal mixer and a turning table that allows the drum to rotate during the mixing operation, simulating a planetary mixer. The facility was designed to treat contact handled liquids and wet solid wastes, but can be adapted for shielded equipment and remote operation. (author)

  12. 21 CFR 872.3275 - Dental cement.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dental cement. 872.3275 Section 872.3275 Food and... DENTAL DEVICES Prosthetic Devices § 872.3275 Dental cement. (a) Zinc oxide-eugenol—(1) Identification... filling or as a base cement to affix a temporary tooth filling, to affix dental devices such as crowns or...

  13. Cement production from coal conversion residues

    International Nuclear Information System (INIS)

    Brown, L.D.; Clavenna, L.R.; Eakman, J.M.; Nahas, N.C.

    1981-01-01

    Cement is produced by feeding residue solids containing carbonaceous material and ash constituents obtained from converting a carbonaceous feed material into liquids and/or gases into a cement-making zone and burning the carbon in the residue solids to supply at least a portion of the energy required to convert the solids into cement

  14. Multicomponent modelling of Portland cement hydration reactions

    NARCIS (Netherlands)

    Ukrainczyk, N.; Koenders, E.A.B.; Van Breugel, K.

    2012-01-01

    The prospect of cement and concrete technologies depends on more in depth understanding of cement hydration reactions. Hydration reaction models simulate the development of the microstructures that can finally be used to estimate the cement based material properties that influence performance and

  15. THE USE OF PANAX GINSENG AND ITS ANALOGUES AMONG PHARMACY CUSTOMERS IN ESTONIA: A CROSS-SECTIONAL STUDY.

    Science.gov (United States)

    Volmer, Dasy; Raal, Ain; Kalle, Raivo; Sõukand, Renata

    2016-01-01

    The aim of the cross-sectional study was to evaluate the pattern of complementary self-treatment with P. ginseng and its analogues amongst pharmacy customers in Estonia. The study instrument consisted of multiple-choice items related to personal knowledge about and experience with the use of P. ginseng and its analogues. In total, 1233 customers participated in the study. Of study participants, 18.1% reported the use of P. ginseng and its analogues in their lives. P. ginseng preparations were used mostly according to the well- known indications (tiredness, weakness and decreased mental and physical capacity). Of P. ginseng users 44.3% reported positive treatment effects and 12.0% had experienced different side effects. With increase of age (p < 0.01) and at lower levels of education (p = 0.04), the use of ginseng or its analogues decreased. The better the users evaluated their health, the better they perceived the effect of P. ginseng preparations (p < 0.01). This study reported rather frequent use of P. ginseng and its analogues. P. ginseng could be seen in the treatment of conditions, where the use of local medicinal plants has not been established. Further research is needed to learn more about public knowledge and experiences about efficacy and safety of P. ginseng and its analogues.

  16. National Emission Standards for Hazardous Air Pollutants (NESHAP) for the Portland Cement Manufacturing Industry Subpart LLL Rule Guidance

    Science.gov (United States)

    This Spring 2016 document is intended for the use of EPA staff, State and Local regulatory agencies and their staff, and industry plant managers for the NESHAP for the Portland Cement Manufacturing Industry.

  17. Energy consumption and CO2 emissions in China's cement industry: A perspective from LMDI decomposition analysis

    International Nuclear Information System (INIS)

    Xu Jinhua; Fleiter, Tobias; Eichhammer, Wolfgang; Fan Ying

    2012-01-01

    We analyze the change of energy consumption and CO 2 emissions in China's cement industry and its driving factors over the period 1990–2009 by applying a log-mean Divisia index (LMDI) method. It is based on the typical production process for clinker manufacturing and differentiates among four determining factors: cement output, clinker share, process structure and specific energy consumption per kiln type. The results show that the growth of cement output is the most important factor driving energy consumption up, while clinker share decline, structural shifts mainly drive energy consumption down (similar for CO 2 emissions). These efficiency improvements result from a number of policies which are transforming the entire cement industry towards international best practice including shutting down many older plants and raising the efficiency standards of cement plants. Still, the efficiency gains cannot compensate for the huge increase in cement production resulting from economic growth particularly in the infrastructure and construction sectors. Finally, scenario analysis shows that applying best available technology would result in an additional energy saving potential of 26% and a CO 2 mitigation potential of 33% compared to 2009. - Highlights: ► We analyze the energy consumption and CO 2 emissions in China's cement industry. ► The growth of cement output is the most important driving factor. ► The efficiency policies and industrial standards significantly narrowed the gap. ► Efficiency gains cannot compensate for the huge increase in cement production. ► The potentials of energy-saving of 26% and CO 2 mitigation of 33% exist based on BAT.

  18. Industrial trial to produce a low clinker, low carbon cement

    Directory of Open Access Journals (Sweden)

    Vizcaíno-Andrés, L. M.

    2015-03-01

    Full Text Available A preliminary assessment of conditions for the industrial manufacture of a new cementitious system based on clinker-calcined clay and limestone, developed by the authors, referred as “low carbon cement” is presented. The new cement enables the substitution of more than 50% of the mass of clinker without compromising performance. The paper presents the follow-up of an industrial trial carried out in Cuba to produce 130 tonnes of the new cement at a cement plant. The new material proved to fulfill national standards in applications such as the manufacture of hollow concrete blocks and precast concrete. No major differences either in the rheological or mechanical properties were found when compared with Portland cement. Environmental assessment of the ternary cement was made, which included comparison with other blended cements produced industrially in Cuba. The new cement has proven to contribute to the reduction of above 30% of carbon emissions on cement manufacture.Se presenta la evaluación preliminar de las condiciones de fabricación industrial de un nuevo sistema cementicio a partir del empleo de clínquer; arcillas calcinadas y piedra caliza; desarrollado por los autores; denominado “cemento de bajo carbono”. El nuevo cemento posibilita la reducción de más de un 50% de la masa de clínquer; sin comprometer el comportamiento del material. El presente trabajo presenta el monitoreo de la producción industrial en una planta en Cuba; de 130 t del nuevo cemento. El cemento obtenido cumple con las regulaciones nacionales de calidad y su empleo tiene similar rendimiento que el cemento Pórtland para la producción de bloques y hormigón de 25 MPa. Se realiza el análisis de impacto ambiental del cemento ternario mediante la comparación con otros cementos producidos industrialmente. El nuevo cemento puede contribuir a la reducción de más del 30% de las emisiones de CO2 asociadas a la manufactura de cemento.

  19. Device for cementing radioactive of toxic waste into barrels

    International Nuclear Information System (INIS)

    Hempelmann, W.; Waldenmeier, G.; Mathis, P.; Mathis, B.; Mathis, F.

    1987-01-01

    The plant consists of conventional means, such as through mixers and dosing and transport spirals, which are accommodated in a glovebox. The inactive additives cement and sand and the active materials evaporation concentrates and sludges are mixed by them, and are then filled into a waste barrel which is empty or already filled with solid waste. Liquid radioactive wastes are used to concrete over the solid waste. (DG) [de

  20. Study on the alternative mitigation of cement dust spread by capturing the dust with fogging method

    Science.gov (United States)

    Purwanta, Jaka; Marnoto, Tjukup; Setyono, Prabang; Handono Ramelan, Ari

    2017-12-01

    The existence of a cement plant impact the lives of people around the factory site. For example the air quality, which is polluted by dust. Cement plant has made various efforts to mitigate the generated dust, but there are still alot of dust fly inground either from the cement factory chimneys or transportation. The purpose of this study was to conduct a review of alternative mitigation of the spread of dust around the cement plant. This study uses research methods such as collecting secondary data which includes data of rain density, the average rains duration, wind speed and direction as well as data of dust intensity quality around PT. Semen Gresik (Persero) Tbk.Tuban plant. A soft Wind rose file is used To determine the wind direction propensity models. The impact on the spread of dust into the environment is determined using secondary data monitoring air quality. Results of the study is that the mitigation of dust around the cement plant is influenced by natural factors, such as the tendency of wind direction, rain fall and rainy days, and the rate of dust emission from the chimney. The alternative means proposed is an environmental friendly fogging dust catcher.

  1. Environmental health survey in asbestos cement sheets manufacturing industry.

    Science.gov (United States)

    Ansari, F A; Bihari, V; Rastogi, S K; Ashquin, M; Ahmad, I

    2007-01-01

    About 673 small-scale asbestos mining and milling facilities and 33 large - scale asbestos manufacturing plants, (17 asbestos-cement product manufacturing plants and 16 other than asbestos-cement product plants) are situated in India. The present study reveals the exposure of commercial asbestos (chrysotile) in the occupational as well as ambient air environment of the asbestos-cement (AC) sheets industry using membrane filter method of Bureau of Indian Standards (BIS). The fibre concentrations in 15 samples collected in the occupational environment at ingredient feeding site, sheet-producing site, fibre godown were 0.079, 0.057 and 0.078 f/cc, respectively and in five samples from surrounding ambient air at factory gate resulted fibre concentration of 0.071 f/cc. All the samples have shown fibre concentration lower than the threshold limit values (TLVs) prescribed by BIS. Morphological analysis of samples, further under phase contrast and polarized microscopy indicates the presence of chrysotile asbestos, which acts as carcinogen as well as co-carcinogen. A clinical examination of exposed subjects reveals that there was no case of clubbing, crepitation, ronchi and dyspnea on exertion; however, obstruction and restriction were 10.9 per cent and 25 per cent in exposed subjects, respectively while in control there were 12 per cent and 28 per cent, respectively. The study revealed that chrysotile asbestos is emitted in the occupational as well as ambient environment that may cause adverse health impact.

  2. Peach leaf responses to soil and cement dust pollution.

    Science.gov (United States)

    Maletsika, Persefoni A; Nanos, George D; Stavroulakis, George G

    2015-10-01

    Dust pollution can negatively affect plant productivity in hot, dry and with high irradiance areas during summer. Soil or cement dust were applied on peach trees growing in a Mediterranean area with the above climatic characteristics. Soil and cement dust accumulation onto the leaves decreased the photosynthetically active radiation (PAR) available to the leaves without causing any shade effect. Soil and mainly cement dust deposition onto the leaves decreased stomatal conductance, photosynthetic and transpiration rates, and water use efficiency due possibly to stomatal blockage and other leaf cellular effects. In early autumn, rain events removed soil dust and leaf functions partly recovered, while cement dust created a crust partially remaining onto the leaves and causing more permanent stress. Leaf characteristics were differentially affected by the two dusts studied due to their different hydraulic properties. Leaf total chlorophyll decreased and total phenol content increased with dust accumulation late in the summer compared to control leaves due to intense oxidative stress. The two dusts did not cause serious metal imbalances to the leaves, except of lower leaf K content.

  3. Joint implementation demo project between Denmark and Estonia - Phase 1. Final report

    International Nuclear Information System (INIS)

    2003-09-01

    This project is meant to contribute to form the basis of co-operation between Denmark and Estonia as regards Joint Implementation (JI) and thus gather experience in preparation for practical use of JI. A number of questions can be raised for discussion within this project: What is the scope for JI? What is the role of the host country government? Will JI survive the emerging Emission Trading? The project report gives a status of the present situation within the area of JI both internationally and in Estonia, including a resume of the Estonian National Climate Programme. Furthermore, a stakeholder analysis is presented, along with an illustration of the effect of Joint Implementation in the various energy sectors. (BA)

  4. The Path to and Lessons from the Economic Crisis in Estonia: Employee Compensation Development

    Directory of Open Access Journals (Sweden)

    Janno Reiljan

    2013-01-01

    Full Text Available The aim of this article is to describe Estonia’s economic development strategy in the Baltic Sea region primarily from the perspective of labour costs as a factor in international competitiveness. Estonia’s position in the international division of economic activities will be explored based on expert assessments in the context of a study of theoretical literature about labour compensation as a factor in international competitiveness. The differences between the impact of the economic boom and crisis periods on the level and dynamics of employee compensation (labour related expenditures, and gross and net salary in Estonia at the national level will be empirically analysed. An empirical analysis will also be performed to describe the changes in the structure of economic activities (NACE-classification in Estonia

  5. Cost of Capital in Price-regulated Companies: the Case of Estonia

    Directory of Open Access Journals (Sweden)

    Priit Sander

    2013-01-01

    Full Text Available In case of price-regulated companies it is the role of appropriate government agencies to introduce clear, internally consistent, theoretically sound, and unambiguous methodology for finding the regulative cost of capital. The aim of the paper is to describe and analyze the cost of capital estimation methodology for regulated companies in Estonia and discuss some issues arising in applying this methodology. The current paper focuses on two topical issues associated with the estimation of regulative cost of capital in Estonia: estimation of market risk premium and inclusion of currency risk premium into the cost of capital. Current turmoil in financial markets has increased investors’ risk aversion as well as level of risks.

  6. Labour market adjustments in Estonia during the 2008/2011 crisis

    Directory of Open Access Journals (Sweden)

    Sandrine LEVASSEUR

    2012-06-01

    Full Text Available his article provides an assessment of labour market adjustments occurring in Estonia during the 2008/2011 crisis. The strategy of internal devaluation succeeded in shrinking the real (hourly unit labour costs by 25 % per year in 2010 and 2011, thus helping Estonian enterprises gain international competitiveness. The whole gamut of tools available in terms of flexibility was used, at least in the worst time of the financial crisis: massive lay-offs, reduced working time and wage cuts. In 2011, Estonia stood as one of the most dynamic EU countries to recover with exports growth. On the social side, however, the track record is not positive: the purchasing power of workers has been reduced and unemployment still remains strong and persistent despite economic recovery.

  7. Research Policies Rewarding Quantity: Estonia and Ukraine. Kvantiteeti tasustav teaduspoliitika: Eesti ja Ukraina

    Directory of Open Access Journals (Sweden)

    Kadri Ukrainski

    2016-10-01

    Full Text Available This article is resting on the theoretical model of Braun (2003 describing the delegation modes for public funding of research in the principal-agent framework. It aims to show by using the conceptualisation of utility functions of principal and agents on the various levels, how different motivations for producing different kinds of research outputs emerge for researchers and universities or public research organisations in Estonia and Ukraine. The article attempts to offer one explanation to why in some quantitative research output indicators both countries perform very well compared to much lower levels of innovation system indicators otherwise. Estonia is rewarding publications and Ukraine is rewarding utility model applications throughout different levels of the system.

  8. The origin of barium in the Cambrian–Vendian aquifer system, North Estonia

    Directory of Open Access Journals (Sweden)

    Mokrik, Robert

    2009-09-01

    Full Text Available Identification of the barium occurrence and its origin is made on the basis of the groundwater chemistry study. High Ba content has been detected in the Cambrian–Vendian aquifer system in the coastal vicinity of the Gulf of Finland in Estonia and St Petersburg. The dissolution of Ba from witherite as the primary source was derived from the analysis of the aqueous solution equilibrium with Ba-related minerals. It is reflected in the chemical composition of groundwater and influenced by the galenite–calcite–fluorite polymetallic mineralization in Vendian sandstones. The dissolution and re-deposition of carbonates and baryte are confirmed by mineral saturation states for an aqueous solution and distribution of other species in the groundwater of the Cambrian–Vendian aquifer system in North Estonia.

  9. E-Participation in the Legislative Process Lessons from Estonia for Enhancing Democratic Empowerment

    Directory of Open Access Journals (Sweden)

    Andrew Glencross

    2009-09-01

    Full Text Available This paper assesses the success of an innovative national e-participation project in Estonia. To carry out this task, the paper combines quantitative (aggregate user data, content analysis via tagging and qualitative (individual user survey and interviews with public officials data analysis. The analysis is conducted with two principal research objectives in mind. Firstly, to explain how e-participation has fared in Estonia, both in terms of citizen mobilization and government responses. The second goal is to evaluate a series of procedural and technological changes for enhancing e-participation. The Estonian case provides ample lessons for ensuring that e-participation in practice can better meet the expectations of users and government officials alike.

  10. Historical Survey of Nuclear Non-Proliferation in Estonia, 1946-1995

    International Nuclear Information System (INIS)

    Maremaee, Ello; Tankler, Hain; Putnik, Henno; Maalmann, Iige

    2003-12-01

    The report presents a historical survey on two of the nuclear facilities under the IAEA safeguards in Estonia - Sillamaee Uranium Extraction Factory and the Paldiski Submarine Training Centre. These facilities were a Soviet legacy and shall be decommissioned and it is only through a close international co-operation and technical assistance that it would be possible to solve all the problems arising at these facilities. The historical survey represents the best available information the authors were able to give on the nuclear facilities, which have functioned on the territory of Estonia. The historical survey was a joint co-operation initiative by the Estonian Radiation Protection Centre and the Swedish Nuclear Power Inspectorate. The historical survey will be presented to the IAEA as a volunteer supplement to the State Declaration according to the Additional Protocol (author)

  11. Spatial Planning in Estonia – From A Socialist to Inclusive Perspective

    Directory of Open Access Journals (Sweden)

    Mart HIOB

    2016-02-01

    Full Text Available Spatial planning in Eastern Europe has gone through major changes during the years after the Soviet occupation ended around 1990. New planning standards were eagerly accepted but the practice was often carried out in a socialist manner. This article gives an overview of planning law and practice in Estonia during the transition period. The example presented is a district in Tartu, the second largest city of 100,000 inhabitants. The article analyses different master planning documents covering the whole district and compares both their process of compilation and their content to former Soviet era plans. The conclusion is that the transition from socialist to inclusive planning in Estonia has taken at least two decades, and the process is still not fi nished. This shows that the legal framework alone is not suffi cient to transform planning practice – a new ideology has to be accepted by the specialist as well as the politicians and the general public.

  12. Helminthologic survey of the wolf (Canis lupus) in Estonia, with an emphasis on Echinococcus granulosus.

    Science.gov (United States)

    Moks, E; Jõgisalu, I; Saarma, U; Talvik, H; Järvis, T; Valdmann, H

    2006-04-01

    Carcasses of 26 wolves were collected during the 2000/2001 and 2003/2004 hunting seasons and examined for helminths. Thirteen helminth species were recorded: one trematode (Alaria alata), seven cestodes (Diphyllobothrium latum, Mesocestoides lineatus, Taenia hydatigena, Taenia multiceps, Taenia ovis, Taenia pisiformis, and Echinococcus granulosus), and five nematode species (Uncinaria stenocephala, Toxascaris leonina, Toxocara canis, Trichinella nativa, and Trichinella britovi). The most common species were A. alata and U. stenocephala. Mature Echinococcus granulosus was found and described for the first time in Estonia, and its identity verified using PCR-RFLP analysis. Sequencing a fragment of the mitochondrial DNA NADH dehydrogenase 1 (mtND1) gene showed that the E. granulosus strain from Estonia was identical to strain G10, recently characterized in reindeer and moose in Finland.

  13. Business environments versus corporate survival in Estonia and Poland in 2001–2009

    Directory of Open Access Journals (Sweden)

    Grzegorz Gołębiowski

    2010-03-01

    Full Text Available Corporate longevity is - in essence - determined by a company's intrinsic competitive advantage (sometimes dubbed a "moat" as well as exogenous factors: from business doing ease - to broader, macroeconomic and strategic factors. In this study, we have endeavoured to compare the business environments and corporate sectors of two recent entrants into the European Union: Estonia and Poland. Overall, Estonia, thanks to greater resolve in post-communist liberal transition, has consistently ensured a superior corporate governance framework. Surprisingly, it is the macroeconomic and strategic steadiness that led to higher corporate survival in Poland. The global economic crisis of 2007-2009 is expected to further back this claim, as the patterns of macroeconomic growth for both countries are set to widen.

  14. Use of waste fuels in cement works. Application of the 17th Ordinance for the Protection against Nuisances (BImSchV) to plants for baking cement clinkers; Einsatz von Sonderbrennstoffen in Zementwerken. Anwendung der 17. BlmSchV auf Anlagen zum Brennen von Zementklinker

    Energy Technology Data Exchange (ETDEWEB)

    Mair, K. [Bayerisches Landesamt fuer Umweltschutz, Muenchen (Germany)

    1995-06-01

    In cement works, other fuels besides the regular ones - coal, heavy fuel and natural gas - are used. Burning these materials requires proper handling and must correspond to state-of-the-art practices, especially as regards clean air measures. The ordinance on fire-places for wastes and other fuel materials (17th ordinance for the protection against nuisances) contains not only relevant emission limits but makes also stipulations as to the design of fire-places, emission monitoring, and general rules. (orig.) [Deutsch] In der Zementindustrie werden neben den sogenannten Regelbrennstoffen wie Kohle, Heizoel S und Erdgas auch Sonderbrennstoffe eingesetzt. Der Einsatz dieser Stoffe setzt jedoch eine ordnungsgemaesse Handhabung bei gleichzeitiger Einhaltung der dem Stand der Technik entsprechenden Massnahmen, besonders zur Luftreinhaltung, voraus. In der Verordnung ueber Verbrennungsanlagen fuer Abfaelle und aehnliche brennbare Stoffe (17. BlmSchV) werden hierzu neben den Emissionsbegrenzungen auch Anforderungen an die Beschaffenheit der Feuerungen, die Emissionsueberwachung sowie allgemeine Regelungen vorgegeben. (orig.)

  15. Electrically conductive Portland cement concrete.

    Science.gov (United States)

    1986-01-01

    There is a need for an effective, simple-to-install secondary anode system for use in the cathodic protection of reinforced concrete bridge decks. In pursuit of such a system, carbon fibers and carbon black were incorporated in portland cement concre...

  16. Polymer reinforcement of cement systems

    International Nuclear Information System (INIS)

    Swamy, R.N.

    1979-01-01

    In the last couple of decades several cement- and concrete-based composites have come into prominence. Of these, cement-polymer composites, like cement-fibre composites, have been recognised as very promising, and considerable research and development on their properties, fabrication methods and application are in progress. Of the three types of concrete materials which incorporate polymers to form composites, polymer impregnated concrete forms a major development in which hardened concrete is impregnated with a liquid monomer which is subsequently polymerized to form a rigid polymer network in the pores of the parent material. In this first part of the extensive review of the polymer reinforcement of cement systems, the process technology of the various monomer impregnation techniques and the properties of the impregnated composite are assessed critically. It is shown that the high durability and superior performance of polymer impregnated concrete can provide an economic and competitive alternative in in situ strengthening, and in other areas where conventional concrete can only at best provide adequate performance. The review includes a section on radiation-induced polymerization. (author)

  17. Influence of Blended Cements with Calcareous Fly Ash on Chloride Ion Migration and Carbonation Resistance of Concrete for Durable Structures

    Directory of Open Access Journals (Sweden)

    Michał A. Glinicki

    2016-01-01

    Full Text Available The objective of this paper is to examine the possible use of new blended cements containing calcareous fly ash in structural concrete, potentially adequate for structural elements of nuclear power plants. The investigation included five new cements made with different contents of non-clinker constituents: calcareous fly ash, siliceous fly ash, ground granulated blastfurnace slag, and a reference cement—ordinary Portland cement. The influence of innovative cements on the resistance of concrete to chloride and carbonation exposure was studied. Additionally, an evaluation of the microstructure was performed using optical microscopy on concrete thin sections. Test results revealed a substantial improvement of the resistance to chloride ion penetration into concrete containing blended cements. The resistance was higher for increased clinker replacement levels and increased with curing time. However, concrete made with blended cements exhibited higher depth of carbonation than the Portland cement concrete, except the Portland-fly ash cement with 14.3% of calcareous fly ash. The thin sections analysis confirmed the values of the carbonation depth obtained from the phenolphthalein test. Test results indicate the possible range of application for new cements containing calcareous fly ash.

  18. Environmental priority action programme for Leningrad, Leningrad Region, Karelia and Estonia

    International Nuclear Information System (INIS)

    1991-01-01

    The Finnish Government has drawn up a plan of action concerning co-operation in the near future with Eastern European countries. Go-operation in the field of environmental protection occupies a central position in the plan. In connection with the plan, an Environmental Review and Priority Action Programme for Leningrad, Leningrad region, Karelia and Estonia has been made to determine the main environmental problems and the main measures to reduce them

  19. Uudised : "Eesti väärtorelid" 3. Verdi festival Estonias. Leedu ooper 80 / Tiina Mattisen

    Index Scriptorium Estoniae

    Mattisen, Tiina

    2001-01-01

    6. jaan. esitleti Jaani kirikus sarja "Eesti väärtorelid" kolmandat CDd, mis jäädvustab A. Terkmanni 1913.a valminud oreli kõla. G. Verdi 100. surma-aastapäevale pühendatud Verdi festivalist Rahvusooperis Estonia 19.-27. jaan. Leedu Rahvuslik Ooperi- ja Balletiteater tähistas leedu ooperikunsti 80. sünnipäeva 30. dets. galakontserdiga, Estoniat esindas M. Palm

  20. Decline in alcohol consumption in Estonia: combined effects of strengthened alcohol policy and economic downturn.

    Science.gov (United States)

    Lai, Taavi; Habicht, Jarno

    2011-01-01

    To describe alcohol policy changes in parallel to consumption changes in 2005-2010 in Estonia, where alcohol consumption is among the highest in Europe. Review of pertinent legislation and literature. Alcohol consumption decreased since 2008, while alcohol excise tax, sales time restrictions and ad bans have increased since 2005. An economic downturn started in 2008. The precise roles of policy changes and the economic downturn in the decline of alcohol consumption, and whether the decrease will be sustained, are still unclear.

  1. Cruziana traces from the Late Silurian (Pridoli carbonate shelf of Saaremaa, Estonia

    Directory of Open Access Journals (Sweden)

    Olev Vinn

    2014-05-01

    Full Text Available Late Pridoli Cruziana traces have recently been found in carbonate shelf sediments of the Ohesaare Formation on Saaremaa Island, Estonia. Cruziana isp. is interpreted here as a locomotory trace (repichnia of an arthropod, possibly a trilobite. Cruziana traces previously known from the Silurian of Baltica differ from Cruziana isp., indicating that the diversity of Cruziana traces in the late Silurian of Baltica was higher than previously thought.

  2. Estonia hukk jõuab Eesti kinodesse sügisel / Tiit Tuumalu

    Index Scriptorium Estoniae

    Tuumalu, Tiit, 1971-

    2003-01-01

    Saksamaal peatselt esilinastuv poliitiline põnevusfilm "Balti torm" ("Baltic Storm"), mis kujutab parvlaev "Estonia" hukku venelaste vandenõu tulemusena, jõuab Eestis siinse levitaja Mati Seppingu sõnul linale novembri alul. Produtsendid on Jutta Rabe ja Kaj Holmberg, peaosades Greta Scacchi ja Jürgen Prochnow. Kaasa teeb ka Donald Sutherland USA kindrali rollis. Eesti näitlejaist on kapten Arvo Kallase rollis Rein Oja

  3. [Cement augmentation on the spine : Biomechanical considerations].

    Science.gov (United States)

    Kolb, J P; Weiser, L; Kueny, R A; Huber, G; Rueger, J M; Lehmann, W

    2015-09-01

    Vertebral compression fractures are the most common osteoporotic fractures. Since the introduction of vertebroplasty and screw augmentation, the management of osteoporotic fractures has changed significantly. The biomechanical characteristics of the risk of adjacent fractures and novel treatment modalities for osteoporotic vertebral fractures, including pure cement augmentation by vertebroplasty, and cement augmentation of screws for posterior instrumentation, are explored. Eighteen human osteoporotic lumbar spines (L1-5) adjacent to vertebral bodies after vertebroplasty were tested in a servo-hydraulic machine. As augmentation compounds we used standard cement and a modified low-strength cement. Different anchoring pedicle screws were tested with and without cement augmentation in another cohort of human specimens with a simple pull-out test and a fatigue test that better reflects physiological conditions. Cement augmentation in the osteoporotic spine leads to greater biomechanical stability. However, change in vertebral stiffness resulted in alterations with the risk of adjacent fractures. By using a less firm cement compound, the risk of adjacent fractures is significantly reduced. Both screw augmentation techniques resulted in a significant increase in the withdrawal force compared with the group without cement. Augmentation using perforated screws showed the highest stability in the fatigue test. The augmentation of cement leads to a significant change in the biomechanical properties. Differences in the stability of adjacent vertebral bodies increase the risk of adjacent fractures, which could be mitigated by a modified cement compound with reduced strength. Screws that were specifically designed for cement application displayed greatest stability in the fatigue test.

  4. Three Thousand Years of Continuity in the Maternal Lineages of Ancient Sheep (Ovis aries) in Estonia

    Science.gov (United States)

    Rannamäe, Eve; Lõugas, Lembi; Speller, Camilla F.; Valk, Heiki; Maldre, Liina; Wilczyński, Jarosław; Mikhailov, Aleksandr; Saarma, Urmas

    2016-01-01

    Although sheep (Ovis aries) have been one of the most exploited domestic animals in Estonia since the Late Bronze Age, relatively little is known about their genetic history. Here, we explore temporal changes in Estonian sheep populations and their mitochondrial genetic diversity over the last 3000 years. We target a 558 base pair fragment of the mitochondrial hypervariable region in 115 ancient sheep from 71 sites in Estonia (c. 1200 BC–AD 1900s), 19 ancient samples from Latvia, Russia, Poland and Greece (6800 BC–AD 1700), as well as 44 samples of modern Kihnu native sheep breed. Our analyses revealed: (1) 49 mitochondrial haplotypes, associated with sheep haplogroups A and B; (2) high haplotype diversity in Estonian ancient sheep; (3) continuity in mtDNA haplotypes through time; (4) possible population expansion during the first centuries of the Middle Ages (associated with the establishment of the new power regime related to 13th century crusades); (5) significant difference in genetic diversity between ancient populations and modern native sheep, in agreement with the beginning of large-scale breeding in the 19th century and population decline in local sheep. Overall, our results suggest that in spite of the observed fluctuations in ancient sheep populations, and changes in the natural and historical conditions, the utilisation of local sheep has been constant in the territory of Estonia, displaying matrilineal continuity from the Middle Bronze Age through the Modern Period, and into modern native sheep. PMID:27732668

  5. Exposure to High Fluoride Drinking Water and Risk of Dental Fluorosis in Estonia

    Directory of Open Access Journals (Sweden)

    Ene Indermitte

    2009-02-01

    Full Text Available The purpose of this study was to assess exposure to drinking water fluoride and evaluate the risk of dental fluorosis among the Estonian population. The study covered all 15 counties in Estonia and 93.7% of population that has access to public water supplies. In Estonia groundwater is the main source for public water supply systems in most towns and rural settlements. The content of natural fluoride in water ranges from 0.01 to 7.20 mg/L. The exposure to different fluoride levels was assessed by linking data from previous studies on drinking water quality with databases of the Health Protection Inspectorate on water suppliers and the number of water consumers in water supply systems. Exposure assessment showed that 4% of the study population had excessive exposure to fluoride, mainly in small public water supplies in western and central Estonia, where the Silurian-Ordovician aquifer system is the only source of drinking water. There is a strong correlation between natural fluoride levels and the prevalence of dental fluorosis. Risk of dental fluorosis was calculated to different fluoride exposure levels over 1.5 mg/L.

  6. The Phenomenon of Trust in Flat Owners’ Collective Renovation Strategies in Estonia

    Directory of Open Access Journals (Sweden)

    Liis Ojamäe

    2015-12-01

    Full Text Available Mobilising fl at owners into renovating residential blocks in post-socialist countries has been a complicated process. Evidence from Estonia shows that the success of collective renewal strategies depends not only on economic issues but also on ways investments are organised and, signifi cantly, the relationship of trust between diff erent actors. The paper aims at conceptualising the issue of institutional trust upon the experience of urban housing renewal in Estonia. It is contended that trust is crucial for the joint decision-making in a block as well as for facilitating negotiations between fl at owners’ associations, local municipalities and market actors. The paper draws on three qualitative studies conducted in Estonia during the 2000s, which allow asserting that trust towards new strategies of housing renewal can be achieved and maintained by ‘best practices’, which by concentrating expert knowledge also denote direct communication between experts and fl at owners. While it is important to raise the residents’ technical knowledgeability, it is indispensable to develop abilities to manage and communicate the renovation process between diff erent parties. The public sector is conceived to be a central actor in sustaining trust between actors who have no previous positive experience from collective residential strategies

  7. 25 Years of Change in Management Control Systems and Business Education in Estonia

    Directory of Open Access Journals (Sweden)

    Ülle Pärl

    2017-06-01

    Full Text Available During the last 25 years, the Estonian economy has transitioned from a centrally planned economy to a market-oriented, globally open, highly competitive economy. Although during these years there has been fast growth and Estonians could tell a lot of success stories, research shows that management practices are still less advanced compared to those in enterprises from developed countries. Increased competition, openness and innovation increased the significance of more sophisticated management control systems (MCS. Researchers accentuate the role of managers and their education and training in using and developing more sophisticated MCS in companies. The objective of the current paper is to better understand how changes in the business environment, managerial training and education are connected to developments in MCS in Estonia. This article provides an overview of the statistics and studies completed in Estonia over the last 25 years. As this study shows, the last decade has brought a different level of internationalization and development in the business environment and business education. The problems associated with developments in MCS , using cloud technology, business education and managerial training are the same in Estonia as in developed countries. To develop the business and economic environment in the country, Estonian entrepreneurs need high-level data processing, analytical and financial education, and practical training courses.

  8. CO2 Capture by Cement Raw Meal

    DEFF Research Database (Denmark)

    Pathi, Sharat Kumar; Lin, Weigang; Illerup, Jytte Boll

    2013-01-01

    The cement industry is one of the major sources of CO2 emissions and is likely to contribute to further increases in the near future. The carbonate looping process has the potential to capture CO2 emissions from the cement industry, in which raw meal for cement production could be used...... as the sorbent. Cyclic experiments were carried out in a TGA apparatus using industrial cement raw meal and synthetic raw meal as sorbents, with limestone as the reference. The results show that the CO2 capture capacities of the cement raw meal and the synthetic raw meal are comparable to those of pure limestone...... that raw meal could be used as a sorbent for the easy integration of the carbonate looping process into the cement pyro process for reducing CO2 emissions from the cement production process....

  9. Leaching of tritium from a cement composite

    International Nuclear Information System (INIS)

    Matsuzuru, Hideo; Ito, Akihiko

    1978-10-01

    Leaching of tritium from cement composites into an aqueous phase has been studied to evaluate the safety of incorporation of the tritiated liquid waste into cement. Leaching tests were performed by the method recommended by the International Atomic Energy Agency. The Leaching fraction was measured as functions of waste-cement ratio (Wa/C), temperature of leachant and curing time. The tritium leachability of cement in the long term test follows the order: alumina cement portland cement slag cement. The fraction of tritium leached increases with increasing Wa/C and temperature and decreasing curing period. A deionized water as a leachant gives a slightly higher leachability than synthetic sea water. The amount leached of tritium from a 200 l drum size specimen was estimated on the basis of the above results. (author)

  10. Through BHA (Bottom Hole Assembly) cementing with proprietary cementing technology

    Energy Technology Data Exchange (ETDEWEB)

    Fanguy, Charles ' Joey' ; Mueller, Dan T. [BJ Services Company, Houston, TX (United States); Garrett, J.C. [Palm Energy Partners, LLC, Metairie, LA (United States)

    2004-07-01

    There are many problems that can arise when drilling into sub-normally pressured or naturally fractured zones. Lost circulation is one problem that is commonly encountered while drilling oil and gas wells. Lost circulation can lead to increased costs associated with drilling due to rig time, spreadsheet costs, and expensive mud system losses. Cement is one of the most effective treatment options, although it is not normally considered the first option because most operators are forced to trip out of the wellbore and utilize a squeeze packer. This is not always a viable option because of potential well control issues associated with the hydrostatic pressure reduction due to the losses of the whole mud. One treatment option that is commonly overlooked is pumping cement slurries through the bottom hole assembly and drill bit. This is generally not attempted for a variety of reasons. These reasons include: I Concern about 'squeezing off' of the cement in the bit II Lack of potential quality control associated with mixing 'on the fly' III Lack of the ability to test the actual mixed slurry samples The use of a pre-mixed, storable cement slurry has eliminated the concerns associated with pumping cement slurries through mud motors, MWD tools, BHA's, and drill bits. This advanced cement technology has been successfully utilized while reducing the risks associated with these lost circulation treatments. In addition, this technology has eliminated the costs associated with using a squeeze packer and the rig time required for several trips out of the wellbore. The paper will describe the premixed slurry properties and QA/QC procedures that are required for successful through the bit operations. This paper will also provide case histories of successful through the bit operation, as well as background information leading to the treatments. The case histories include successful through the bit remediation of severe lost circulation zones and as well the

  11. Chemical recycling of carbon dioxide emissions from a cement plant into dimethyl ether, a case study of an integrated process in France using a Reverse Water Gas Shift (RWGS) step

    International Nuclear Information System (INIS)

    Vibhatavata, Phuangphet; Borgard, Jean-Marc; Tabarant, Michel; Bianchi, Daniel; Mansilla, Christine

    2013-01-01

    Recycling of carbon dioxide (CO 2 ) and hydrogen (H 2 ) into liquid fuel technology has recently gained wide public interest since it is a potential pathway to increase the liquid fuel supply and to mitigate CO 2 emissions simultaneously. In France, the majority of the electricity production is derived from nuclear and renewable energy which have a low CO 2 footprint. This electricity power enables a potential for massive hydrogen production with low carbon emissions. We studied the possibility to develop this technology at an industrial scale in the French context on a typical industrial example of a cement manufacture in the south of France. An integrated process is proposed, which enables the use of the heat released by the CO 2 to fuel process to help to capture the CO 2 released by the cement manufacture. Some technological issues are discussed, and a potential solution is proposed for the catalyst used in the critical step of the Reverse Water Gas-Shift reaction (RWGS) of the process. (authors)

  12. Analysis of cement-treated clay behavior by micromechanical approach

    OpenAIRE

    Zhang , Dong-Mei; Yin , Zhenyu; Hicher , Pierre Yves; Huang , Hong-Wei

    2013-01-01

    International audience; Experimental results show the significant influence of cement content on the mechanical properties of cement-treated clays. Cementation is produced by mixing a certain amount of cement with the saturated clay. The purpose of this paper is to model the cementation effect on the mechanical behavior of cement-treated clay. A micromechanical stress-strain model is developed considering explicitly the cementation at inter-cluster contacts. The inter-cluster bonding and debo...

  13. Sustainability of cement kiln co-processing of wastes in India: a pilot study.

    Science.gov (United States)

    Baidya, Rahul; Ghosh, Sadhan Kumar; Parlikar, Ulhas V

    2017-07-01

    Co-processing in cement kiln achieves effective utilization of the material and energy value present in the wastes, thereby conserving the natural resources by reducing the use of virgin material. In India, a number of multifolded initiatives have been taken that take into account the potential and volume of waste generation. This paper studies the factors which might influence the sustainability of co-processing of waste in cement kilns as a business model, considering the issues and challenges in the supply chain framework in India in view of the four canonical pillars of sustainability. A pilot study on co-processing was carried out in one of the cement plant in India to evaluate the environmental performance, economical performance, operational performance and social performance. The findings will help India and other developing countries to introduce effective supply chain management for co-processing while addressing the issues and challenges during co-processing of different waste streams in the cement kilns.

  14. Cement solidification of spent ion exchange resins produced by the nuclear industry

    International Nuclear Information System (INIS)

    Jaouen, C.; Vigreux, B.

    1988-01-01

    Cement solidification technology has been applied to spent ion exchange resins for many years in countries throughout the world (at reactors, research centers and spent fuel reprocessing plants). Changing specifications for storage of radioactive waste have, however, confronted the operators of such facilities with a number of problems. Problems related both to the cement solidification process (water/cement/resin interactions and chemical interactions) and to its utilization (mixing, process control, variable feed composition, etc.) have often led waste producers to prefer other, polymer-based processes, which are very expensive and virtually incompatible with water. This paper discusses research on cement solidification of ion exchange resins since 1983 and the development of application technologies adapted to nuclear service conditions and stringent finished product quality requirements

  15. Synthesis of Portland cement and calcium sulfoaluminate-belite cement for sustainable development and performance

    Science.gov (United States)

    Chen, Irvin Allen

    Portland cement concrete, the most widely used manufactured material in the world, is made primarily from water, mineral aggregates, and portland cement. The production of portland cement is energy intensive, accounting for 2% of primary energy consumption and 5% of industrial energy consumption globally. Moreover, portland cement manufacturing contributes significantly to greenhouse gases and accounts for 5% of the global CO2 emissions resulting from human activity. The primary objective of this research was to explore methods of reducing the environmental impact of cement production while maintaining or improving current performance standards. Two approaches were taken, (1) incorporation of waste materials in portland cement synthesis, and (2) optimization of an alternative environmental friendly binder, calcium sulfoaluminate-belite cement. These approaches can lead to less energy consumption, less emission of CO2, and more reuse of industrial waste materials for cement manufacturing. In the portland cement part of the research, portland cement clinkers conforming to the compositional specifications in ASTM C 150 for Type I cement were successfully synthesized from reagent-grade chemicals with 0% to 40% fly ash and 0% to 60% slag incorporation (with 10% intervals), 72.5% limestone with 27.5% fly ash, and 65% limestone with 35% slag. The synthesized portland cements had similar early-age hydration behavior to commercial portland cement. However, waste materials significantly affected cement phase formation. The C3S--C2S ratio decreased with increasing amounts of waste materials incorporated. These differences could have implications on proportioning of raw materials for cement production when using waste materials. In the calcium sulfoaluminate-belite cement part of the research, three calcium sulfoaluminate-belite cement clinkers with a range of phase compositions were successfully synthesized from reagent-grade chemicals. The synthesized calcium sulfoaluminate

  16. Fiscal 1999 technical survey report. Model project implementation feasibility study in China on effective utilization of cement waste heat; 1999 nendo Chugoku ni okeru cement hainetsu yuko riyo model jigyo jisshi kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Although China ranks first in the world in the manufacture of cement, yet the energy consumption rate is high and there remains room for improvement. Effective utilization of energy at cement making plants will not only profit the industry but also contribute to the stabilization of energy supply for China. The model project on power generation using cement waste heat implemented at Ningguo Cement Plant was concluded successfully. For the purpose of enabling China to domestically manufacture the equipment, the installation of such equipment at Zhujiang Cement Plant and Liuzhou Cement Plant in Guangxi Zhuangzu Zizhiqu was assumed, and their locations and plant operating conditions were studied. In addition, surveys were conducted of manufacturers of important components of the power generation equipment such as boilers, steam turbines, generators, and breaker boards. Two manufacturers were visited for each of the components, and they were checked for records of manufacturing similar equipment, quality assurance and process management capabilities, and for ability to satisfy required specifications. Among the visited manufacturers were Nanjing Turbine and Electric Machinery Co., Jinan Power Equipment Factory, and Hangzhou Boiler Works. Based on the results of the surveys, it was concluded that the model project may be implemented. (NEDO)

  17. Fixation of calcined waste by bituminization or cementation

    International Nuclear Information System (INIS)

    Napravnik, J.; Kyrs, M.; Ditl, P.

    1983-01-01

    The overall concept is given of the combination of calcination with fixation into bitumen, cement etc. The design is shown of a calciner with the capacity of 10 L/h which was tested on real radioactive wastes for 2000 h. The geometrical and operating parameters of the apparatus have been optimized based on a statistical evaluation of the experiments. Wastes containing nitrates are calcined at 300-550 deg. C, yielding oxides. Wastes containing sulphates, carbonates, KMnO 4 , or borates are calcined at 150-330 deg. C, yielding soluble salts. The content of H 3 BO 4 and Na 2 B 4 O 7 and in some cases of sulphates in the calcinate retards hardening of the mixture with cement. Nitrates and detergents also interfere. The effect of the above components on the products mixed with bitumen is much less. Detergents can be decomposed at 200-300 deg. C; organic acids can be reacted with A1 salts to form insoluble substances lowering the leaching rate of Sr and Cs; small amounts of SiO 2 eliminate the effect of borates on cement hardening. The drawbacks of bituminization with bitumen emulsions are the complicated preparation of the emulsion, higher leaching rate of the product and low stability of the emulsion against breaking. The leachability was determined (1-50 days) of different products containing LWR wastes: 33% of concentrated waste in cement of calcination product stabilized with PVA exhibit approx. 8x10 - 3 g/cm 2 per day, 33% of calcine in cement approx. 3x10 - 3 ; 40% concentrate fixed with bitumen emulsion approx. 9x10 - 4 ; 50% calcine stabilized with PVA in bitumen, pilot-plant scale approx. 2x10 - 5 ; the same but on a laboratory scale approx. 1.10 - 5 . (author)

  18. Saksa kirjandus Noor-Eesti ajal. Young Estonia and German Literature

    Directory of Open Access Journals (Sweden)

    Liina Lukas

    2012-04-01

    Full Text Available Impelled by a desire to free themselves from the German influence that had dominated the development of Estonian literature, and from the one-sided relation of cultural dependence that had lasted several hundred years, the Young Estonia movement sought to modernize Estonian literature through borrowing from other European literatures, in particular from French, Scandinavian, and Finnish. This article seeks to clarify the relative importance and selection criteria of translations from German literature for the literary field of the Young Estonia era. Further, I seek to elucidate Young Estonia’s contribution to the renewal of these selection criteria in the first, but more importantly the second decade of the 20th century. The long list of translations from German to Estonian at the beginning of the century speaks of the ”light Muse” of German family newspapers, with an admixture of the following: naturalist light fiction with a social theme and social drama; the historical novel (great favourite of the era of historicism, trendy fiction for both feminine and masculine audiences, and an overwhelming proportion of ”Heimatskunst” (literature of local colour. In the first and second decade of the new century, new names appear on the Estonian literary scene that signal a change in taste. For example, naturalist authors (Kretzer, Hauptmann, Halbe, Dehmel crop up sporadically amidst texts meant for leisure reading. Although the first translations of Nietzsche only appeared in 1901, already in 1902 critics had reason to speak of ”Nietzsche in Estonian literature”. 1910 marked the breakthrough of Viennese modernism in the Estonian literary field (Schnitzler, Altenberg, Bahr. Under the influential protection of the Young Estonians (Suits, Kallas, and published by the Young Estonia Publishing House, Baltic German novellawriter Eduard Keyserling enters the Estonian literary scene. Though ”mass consumption” literature from Germany continued

  19. The state-church relations in Estonia during the years 1944 - 1953

    Directory of Open Access Journals (Sweden)

    Nepochatova Marina

    2014-10-01

    Full Text Available The article features an analysis of the nature and dynamic of church-state relations in Estonia during the first years following its integration into the USSR. In 1944 the religious situation in the republic was characterized by a number of distinctive attributes. The local population, which had lived prior to the accession of the Baltics to the USSR in 1944 in an atmosphere of relative religious freedom, presented the Soviet authorities with a new phenomenon that would have to be reckoned with. The Plenipotentiaries for Estonia appointed by the Council on ROC Affairs at the USSR Council of Ministers were able to convince their superiors of the need to tread carefully in light of the local specifics. The article deals with an analysis of the distinctive features of the Estonian Orthodox Church. As a secondary denomination in the region, it felt the powerful influence of Lutheran customs and rites. The ethnic heterogeneity of the fold and pronounced language barrier determined the choice of candidacy for the ruling eparchy. The Estonian diocese was rather well endowed with cathedrals, meaning that the main problem of church life in the USSR since the easing of persecution in 1944-1947 - the opening of new parishes - was not an issue in Estonia. On the whole, the church-state relations that dominated the republic in 1944-1947 were quite stable, just as they were around the country; moreover, they were typified by a cautious policy on the part of the Soviet authorities. In 1948-1949 the situation began to deteriorate across the country and Estonia was no exception. The difference was in the methods used: in Estonia, the decision was made to fight the Church and its clergy primarily through collectivization, which was actively pursued in the Baltics beginning in the early 1950s. Collectivization left rural parishes and their clergy in dire straits, and religious life in the countryside began to wane. Yet, the arrival from the central regions

  20. Utilization coke dust as fuel in the cement industry

    International Nuclear Information System (INIS)

    Nawaz, S.

    2006-01-01

    Utilization of coke dust available from coal carbonization plants, as a fuel in the cement industry has been undertaken and discussed in this research paper. The parameters studied include physical and chemical evaluation of the coke dust and its economic feasibility/ suitability as fuel for the cement plants. Detailed studies have been carried out on the above referred parameters. In addition a comparative study has been done to access its suitability in comparison to other fuels especially imported coal. It has been found that the coke dust contained about 66% fixed carbon, 29% ash, 4% volatile matter, 1% moisture and 0.48% sulphur. It gross calorific value was found to be 5292 Kcal/kg. The detailed analysis of coke dust ash was also performed to determine as to how its constituents will compare with the cement constituents. Keeping in view the experimental results/ data generated on the coke dust, it has been concluded that it can be quite a good substitute for imported coal. In doing so a substantial financial saving can be achieved which ranges 40-45%. (author)