Adaptive digital beamforming for a CDMA mobile communications payload

Science.gov (United States)

Munoz-Garcia, Samuel G.; Ruiz, Javier Benedicto

1993-01-01

In recent years, Spread-Spectrum Code Division Multiple Access (CDMA) has become a very popular access scheme for mobile communications due to a variety of reasons: excellent performance in multipath environments, high scope for frequency reuse, graceful degradation near saturation, etc. In this way, a CDMA system can support simultaneous digital communication among a large community of relatively uncoordinated users sharing a given frequency band. Nevertheless, there are also important problems associated with the use of CDMA. First, in a conventional CDMA scheme, the signature sequences of asynchronous users are not orthogonal and, as the number of active users increases, the self-noise generated by the mutual interference between users considerably degrades the performance, particularly in the return link. Furthermore, when there is a large disparity in received powers - due to differences in slant range or atmospheric attenuation - the non-zero cross-correlation between the signals gives rise to the so-called near-far problem. This leads to an inefficient utilization of the satellite resources and, consequently, to a drastic reduction in capacity. Several techniques were proposed to overcome this problem, such as Synchronized CDMA - in which the signature sequences of the different users are quasi-orthogonal - and power control. At the expense of increased network complexity and user coordination, these techniques enable the system capacity to be restored by equitably sharing the satellite resources among the users. An alternative solution is presented based upon the use of time-reference adaptive digital beamforming on board the satellite. This technique enables a high number of independently steered beams to be generated from a single phased array antenna, which automatically track the desired user signal and null the unwanted interference source. In order to use a time-reference adaptive antenna in a communications system, the main challenge is to obtain a

Physical Layer Built-In Security Analysis and Enhancement Algorithms for CDMA Systems

Directory of Open Access Journals (Sweden)

Li Tongtong

2007-01-01

Full Text Available Historically developed for secure communication and military use, CDMA has been identified as a major modulation and multiple-access technique for 3G systems and beyond. In addition to the wide bandwidth and low power-spectrum density which make CDMA signals robust to narrowband jamming and easy to be concealed within the noise floor, the physical layer built-in information privacy of CDMA system is provided by pseudorandom scrambling. In this paper, first, security weakness of the operational and proposed CDMA airlink interfaces is analyzed. Second, based on the advanced encryption standard (AES, we propose to enhance the physical layer built-in security of CDMA systems through secure scrambling. Performance analysis demonstrates that while providing significantly improved information privacy, CDMA systems with secure scrambling have comparable computational complexity and overall system performance with that of conventionally scrambled systems. Moreover, it is shown that by scrambling the training sequence and the message sequence separately with two independent scrambling sequences, both information privacy and system performance can be further improved. The proposed scheme can readily be applied to 3G systems and beyond.

A CDMA system implementation with dimming control for visible light communication

Science.gov (United States)

Chen, Danyang; Wang, Jianping; Jin, Jianli; Lu, Huimin; Feng, Lifang

2018-04-01

Visible light communication (VLC), using solid-state lightings to transmit information, has become a complement technology to wireless radio communication. As a realistic multiple access scheme for VLC system, code division multiple access (CDMA) has attracted more and more attentions in recent years. In this paper, we address and implement an improved CDMA scheme for VLC system. The simulation results reveal that the improved CDMA scheme not only supports multi-users' transmission but also maintains dimming value at about 50% and enhances the system efficiency. It can also realize the flexible dimming control by adjusting some parameters of system structure, which rarely affects the system BER performance. A real-time experimental VLC system with improved CDMA scheme is performed based on field programmable gate array (FPGA), reaching a good BER performance.

A Charrelation Matrix-Based Blind Adaptive Detector for DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Zhongqiang Luo

2015-08-01

Full Text Available In this paper, a blind adaptive detector is proposed for blind separation of user signals and blind estimation of spreading sequences in DS-CDMA systems. The blind separation scheme exploits a charrelation matrix for simple computation and effective extraction of information from observation signal samples. The system model of DS-CDMA signals is modeled as a blind separation framework. The unknown user information and spreading sequence of DS-CDMA systems can be estimated only from the sampled observation signals. Theoretical analysis and simulation results show that the improved performance of the proposed algorithm in comparison with the existing conventional algorithms used in DS-CDMA systems. Especially, the proposed scheme is suitable for when the number of observation samples is less and the signal to noise ratio (SNR is low.

A Charrelation Matrix-Based Blind Adaptive Detector for DS-CDMA Systems.

Science.gov (United States)

Luo, Zhongqiang; Zhu, Lidong

2015-08-14

In this paper, a blind adaptive detector is proposed for blind separation of user signals and blind estimation of spreading sequences in DS-CDMA systems. The blind separation scheme exploits a charrelation matrix for simple computation and effective extraction of information from observation signal samples. The system model of DS-CDMA signals is modeled as a blind separation framework. The unknown user information and spreading sequence of DS-CDMA systems can be estimated only from the sampled observation signals. Theoretical analysis and simulation results show that the improved performance of the proposed algorithm in comparison with the existing conventional algorithms used in DS-CDMA systems. Especially, the proposed scheme is suitable for when the number of observation samples is less and the signal to noise ratio (SNR) is low.

On Analyzing LDPC Codes over Multiantenna MC-CDMA System

Directory of Open Access Journals (Sweden)

S. Suresh Kumar

2014-01-01

Full Text Available Multiantenna multicarrier code-division multiple access (MC-CDMA technique has been attracting much attention for designing future broadband wireless systems. In addition, low-density parity-check (LDPC code, a promising near-optimal error correction code, is also being widely considered in next generation communication systems. In this paper, we propose a simple method to construct a regular quasicyclic low-density parity-check (QC-LDPC code to improve the transmission performance over the precoded MC-CDMA system with limited feedback. Simulation results show that the coding gain of the proposed QC-LDPC codes is larger than that of the Reed-Solomon codes, and the performance of the multiantenna MC-CDMA system can be greatly improved by these QC-LDPC codes when the data rate is high.

Performance of an Orthogonal Multicarrier CDMA System in a Multicell/Multipath Environment

Energy Technology Data Exchange (ETDEWEB)

Yoon, W.S. [Ajou University, Suwon (Korea)

1999-08-01

We have considered an improved orthogonal multicarrier (MC) CDMA system. This system combines the advantages of both DS-CDMA with a concatenated spreading scheme and an MC modulation technique to combat the effects of a multipath fading channel and intersymbol interference (IS). The performance of the system is analyzed under a multicell, multiuser, and multipath Rician fading channel. The system is shown to outperform the orthogonal MC-CDMA system with a conventional PN sequence. (author). 4 refs., 3 figs.

Performance of Reverse-Link Synchronous DS-CDMA System on a Frequency-Selective Multipath Fading Channel with Imperfect Power Control

Directory of Open Access Journals (Sweden)

Duk Kyung Kim

2002-08-01

Full Text Available We analyze the performance for reverse-link synchronous DS-CDMA system in a frequency-selective Rayleigh fading channel with an imperfect power control scheme. The performance degradation due to power control error (PCE, which is approximated by a log-normally distributed random variable, is estimated as a function of the standard deviation of the PCE. In addition, we investigate the impacts of the multipath intensity profile (MIP shape and the number of resolvable paths on the performance. Finally, the coded bit error performance is evaluated in order to estimate the system capacity. Comparing with the conventional CDMA system, we show an achievable gain of from 59% to 23% for reverse-link synchronous transmission technique (RLSTT in the presence of imperfect power control over asynchronous transmission for BER=10−6. As well, the effect of tradeoff between orthogonality and diversity can be seen according to the number of multipaths, and the tendency is kept even in the presence of PCE. We conclude that the capacity can be further improved via the RLSTT, because the DS-CDMA system is very sensitive to power control imperfections.

HOT SPOT RELIEF WITH EMBEDDED BEAM FOR CDMA SYSTEMS IN HAPS

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

This paper proposes a novel micro/macro beam coverage scheme used in High Altitude Platform System (HAPS) Code Division Multiple Access (CDMA) systems. A relief of traffic burden in hot spot areas is achieved by embedding micro-beams into the macro-beams at the hot spot locations, together with appropriate power ratio control and user ratio control. The simulation results show that the hot spot problem can be relieved efficiently with the presented configuration, and a higher and more stable system capacity is expectable despite the variation of user distribution.

Differential Space-Time Block Code Modulation for DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Liu Jianhua

2002-01-01

Full Text Available A differential space-time block code (DSTBC modulation scheme is used to improve the performance of DS-CDMA systems in fast time-dispersive fading channels. The resulting scheme is referred to as the differential space-time block code modulation for DS-CDMA (DSTBC-CDMA systems. The new modulation and demodulation schemes are especially studied for the down-link transmission of DS-CDMA systems. We present three demodulation schemes, referred to as the differential space-time block code Rake (D-Rake receiver, differential space-time block code deterministic (D-Det receiver, and differential space-time block code deterministic de-prefix (D-Det-DP receiver, respectively. The D-Det receiver exploits the known information of the spreading sequences and their delayed paths deterministically besides the Rake type combination; consequently, it can outperform the D-Rake receiver, which employs the Rake type combination only. The D-Det-DP receiver avoids the effect of intersymbol interference and hence can offer better performance than the D-Det receiver.

Nonlinear Multiuser Receiver for Optimized Chaos-Based DS-CDMA Systems

Directory of Open Access Journals (Sweden)

S. Shaerbaf

2011-09-01

Full Text Available Chaos based communications have drawn increasing attention over the past years. Chaotic signals are derived from non-linear dynamic systems. They are aperiodic, broadband and deterministic signals that appear random in the time domain. Because of these properties, chaotic signals have been proposed to generate spreading sequences for wide-band secure communication recently. Like conventional DS-CDMA systems, chaos-based CDMA systems suffer from multi-user interference (MUI due to other users transmitting in the cell. In this paper, we propose a novel method based on radial basis function (RBF for both blind and non-blind multiuser detection in chaos-based DS-CDMA systems. We also propose a new method for optimizing generation of binary chaotic sequences using Genetic Algorithm. Simulation results show that our proposed nonlinear receiver with optimized chaotic sequences outperforms in comparison to other conventional detectors such as a single-user detector, decorrelating detector and minimum mean square error detector, particularly for under-loaded CDMA condition, which the number of active users is less than processing gain.

Variable-length code construction for incoherent optical CDMA systems

Science.gov (United States)

Lin, Jen-Yung; Jhou, Jhih-Syue; Wen, Jyh-Horng

2007-04-01

The purpose of this study is to investigate the multirate transmission in fiber-optic code-division multiple-access (CDMA) networks. In this article, we propose a variable-length code construction for any existing optical orthogonal code to implement a multirate optical CDMA system (called as the multirate code system). For comparison, a multirate system where the lower-rate user sends each symbol twice is implemented and is called as the repeat code system. The repetition as an error-detection code in an ARQ scheme in the repeat code system is also investigated. Moreover, a parallel approach for the optical CDMA systems, which is proposed by Marić et al., is also compared with other systems proposed in this study. Theoretical analysis shows that the bit error probability of the proposed multirate code system is smaller than other systems, especially when the number of lower-rate users is large. Moreover, if there is at least one lower-rate user in the system, the multirate code system accommodates more users than other systems when the error probability of system is set below 10 -9.

The research of atmospheric 2D optical PPM CDMA system with turbo coding

Science.gov (United States)

Zhou, Xiuli; Li, Zaoxia

2007-11-01

The atmospheric two-dimensional optical code-division multiple-access (CDMA) systems using pulse-position modulation (PPM) and Turbo-coded were presented. We analyzed the bit-error rate (BER) of the proposed system using pulse-position modulation (PPM) with considering the effects of the scintillation, avalanche photodiode noise, thermal noise, and multi-user interference. We showed that the atmospheric two dimensional (2D) optical PPM CDMA systems can realize high-speed communications when the logarithm variance of the scintillation is less than 0.1, and the turbo-coded atmospheric optical CDMA system has better bit error rate(BER) performance than the atmospheric optical PPM CDMA systems without turbo-coded. We also showed that the turbo-coded system has better performance than the multi-user detection system.

Blind information-theoretic multiuser detection algorithms for DS-CDMA and WCDMA downlink systems.

Science.gov (United States)

Waheed, Khuram; Salem, Fathi M

2005-07-01

Code division multiple access (CDMA) is based on the spread-spectrum technology and is a dominant air interface for 2.5G, 3G, and future wireless networks. For the CDMA downlink, the transmitted CDMA signals from the base station (BS) propagate through a noisy multipath fading communication channel before arriving at the receiver of the user equipment/mobile station (UE/MS). Classical CDMA single-user detection (SUD) algorithms implemented in the UE/MS receiver do not provide the required performance for modern high data-rate applications. In contrast, multi-user detection (MUD) approaches require a lot of a priori information not available to the UE/MS. In this paper, three promising adaptive Riemannian contra-variant (or natural) gradient based user detection approaches, capable of handling the highly dynamic wireless environments, are proposed. The first approach, blind multiuser detection (BMUD), is the process of simultaneously estimating multiple symbol sequences associated with all the users in the downlink of a CDMA communication system using only the received wireless data and without any knowledge of the user spreading codes. This approach is applicable to CDMA systems with relatively short spreading codes but becomes impractical for systems using long spreading codes. We also propose two other adaptive approaches, namely, RAKE -blind source recovery (RAKE-BSR) and RAKE-principal component analysis (RAKE-PCA) that fuse an adaptive stage into a standard RAKE receiver. This adaptation results in robust user detection algorithms with performance exceeding the linear minimum mean squared error (LMMSE) detectors for both Direct Sequence CDMA (DS-CDMA) and wide-band CDMA (WCDMA) systems under conditions of congestion, imprecise channel estimation and unmodeled multiple access interference (MAI).

Super-Orthogonal Space-Time Turbo Transmit Diversity for CDMA

Directory of Open Access Journals (Sweden)

Pieter G. W. van Rooyen

2005-05-01

Full Text Available Studies have shown that transmit and receive diversity employing a combination of multiple transmit-receive antennas (given ideal channel state information (CSI and independent fading between antenna pairs will potentially yield maximum achievable system capacity. In this paper, the concept of a layered super-orthogonal turbo transmit diversity (SOTTD for downlink direct-sequence code-division multiple-access (CDMA systems is explored. This open-loop transmit diversity technique improves the downlink performance by using a small number of antenna elements at the base station and a single antenna at the handset. In the proposed technique, low-rate super-orthogonal code-spread CDMA is married with code-division transmit diversity (CDTD. At the mobile receiver, space-time (ST RAKE CDTD processing is combined with iterative turbo code-spread decoding to yield large ST gains. The performance of the SOTTD system is compared with single- and multiantenna turbo-coded (TC CDTD systems evaluated over a frequency-selective Rayleigh fading channel. The evaluation is done both by means of analysis and computer simulations. The performance results illustrate the superior performance of SOTTD compared to TC CDTD systems over practically the complete useful capacity range of CDMA. It is shown that the performance degradation characteristic of TC CDTD at low system loads (due to the inherent TC error floor is alleviated by the SOTTD system.

Optical CDMA components requirements

Science.gov (United States)

Chan, James K.

1998-08-01

Optical CDMA is a complementary multiple access technology to WDMA. Optical CDMA potentially provides a large number of virtual optical channels for IXC, LEC and CLEC or supports a large number of high-speed users in LAN. In a network, it provides asynchronous, multi-rate, multi-user communication with network scalability, re-configurability (bandwidth on demand), and network security (provided by inherent CDMA coding). However, optical CDMA technology is less mature in comparison to WDMA. The components requirements are also different from WDMA. We have demonstrated a video transport/switching system over a distance of 40 Km using discrete optical components in our laboratory. We are currently pursuing PIC implementation. In this paper, we will describe the optical CDMA concept/features, the demonstration system, and the requirements of some critical optical components such as broadband optical source, broadband optical amplifier, spectral spreading/de- spreading, and fixed/programmable mask.

An efficient digital signal processing method for RRNS-based DS-CDMA systems

Directory of Open Access Journals (Sweden)

Peter Olsovsky

2017-09-01

Full Text Available This paper deals with an efficient method for achieving low power and high speed in advanced Direct-Sequence Code Division Multiple-Access (DS-CDMA wireless communication systems based on the Residue Number System (RNS. A modified algorithm for multiuser DS-CDMA signal generation in MATLAB is proposed and investigated. The most important characteristics of the generated PN code are also presented. Subsequently, a DS-CDMA system based on the combination of the RNS or the so-called Redundant Residue Number System (RRNS is proposed. The enhanced method using a spectrally efficient 8-PSK data modulation scheme to improve the bandwidth efficiency for RRNS-based DS-CDMA systems is presented. By using the C-measure (complexity measure of the error detection function, it is possible to estimate the size of the circuit. Error detection function in RRNSs can be efficiently implemented by LookUp Table (LUT cascades.

A Novel Method of SIR Measurement for Power Control in CDMA Systems

International Nuclear Information System (INIS)

Yu, J; Wu, S B; He, J Z

2006-01-01

CDMA is interference limited multiple access system. Power control is an effective way to reduce co-channel interference and solve the near-far problem. Consequently, it can improve the system capacity, and make higher data rate possible. CDMA2000 employs fast closed-loop power control in reverse link to combat channel fading, and the estimation of signal to interference ratio (SIR) is required for closed-loop power control. Transmitting power is adjusted by comparing the SIR estimation with SIR target. So, it is crucial to measure the SIR of received signal accurately. Traditional measurement methods mostly depend on pilot signal strongly, when the pilots are few, there is a greater error brought to the measurement of SIR. In this paper, we discuss the SIR measurement of the received signal under the fewer pilots condition (especially only one pilot symbol) and present a novel SIR measurement method. According to the simulation, the numerical results indicate that the SIR measured by the proposed method is more accurate than the SIR measured by conventional method under fewer pilots condition

Quadriphase DS-CDMA wireless communication systems employing the generalized detector

Science.gov (United States)

Tuzlukov, Vyacheslav

2012-05-01

Probability of bit-error Per performance of asynchronous direct-sequence code-division multiple-access (DS-CDMA) wireless communication systems employing the generalized detector (GD) constructed based on the generalized approach to signal processing in noise is analyzed. The effects of pulse shaping, quadriphase or direct sequence quadriphase shift keying (DS-QPSK) spreading, aperiodic spreading sequences are considered in DS-CDMA based on GD and compared with the coherent Neyman-Pearson receiver. An exact Per expression and several approximations: one using the characterristic function method, a simplified expression for the improved Gaussian approximation (IGA) and the simplified improved Gaussian approximation are derived. Under conditions typically satisfied in practice and even with a small number of interferers, the standard Gaussian approximation (SGA) for the multiple-access interference component of the GD statistic and Per performance is shown to be accurate. Moreover, the IGA is shown to reduce to the SGA for pulses with zero excess bandwidth. Second, the GD Per performance of quadriphase DS-CDMA is shown to be superior to that of bi-phase DS-CDMA. Numerical examples by Monte Carlo simulation are presented to illustrate the GD Per performance for square-root raised-cosine pulses and spreading factors of moderate to large values. Also, a superiority of GD employment in CDMA systems over the Neyman-Pearson receiver is demonstrated

A novel adaptive joint power control algorithm with channel estimation in a CDMA cellular system

Institute of Scientific and Technical Information of China (English)

无

2005-01-01

Joint power control has advantages of multi-user detection and power control; and it can combat the multi-access interference and the near-far problem. A novel adaptive joint power control algorithm with channel estimation in a CDMA cellular system was designed. Simulation results show that the algorithm can control the power not only quickly but also precisely with a time change. The method is useful for increasing system capacity.

Monte-Carlo Simulation for PDC-Based Optical CDMA System

Directory of Open Access Journals (Sweden)

FAHIM AZIZ UMRANI

2010-10-01

Full Text Available This paper presents the Monte-Carlo simulation of Optical CDMA (Code Division Multiple Access systems, and analyse its performance in terms of the BER (Bit Error Rate. The spreading sequence chosen for CDMA is Perfect Difference Codes. Furthermore, this paper derives the expressions of noise variances from first principles to calibrate the noise for both bipolar (electrical domain and unipolar (optical domain signalling required for Monte-Carlo simulation. The simulated results conform to the theory and show that the receiver gain mismatch and splitter loss at the transceiver degrades the system performance.

Iterative Decoding for an Optical CDMA based Laser communication System

International Nuclear Information System (INIS)

Kim, Jin Young; Kim, Eun Cheol; Cha, Jae Sang

2008-01-01

An optical CDMA(code division multiple access)based Laser communication system has attracted much attention since it requires minimal optical Laser signal processing and it is virtually delay free, while from the theoretical point of view, its performance depends on the auto and cross correlation properties of employed sequences. Various kinds of channel coding schemes for optical CDMA based Laser communication systems have been proposed and analyzed to compensate nonideal channel and receiver conditions in impaired photon channels. In this paper, we propose and analyze an iterative decoding of optical CDMA based Laser communication signals for both shot noise limited and thermal noise limited systems. It is assumed that optical channel is an intensity modulated (IM)channel and direct detection scheme is employed to detect the received optical signal. The performance is evaluated in terms of bit error probability and throughput. It is demonstrated that the BER and throughput performance is substantially improved with interleaver length for a fixed code rate and with alphabet size of PPM (pulse position modulation). Also, the BER and throughput performance is significantly enhanced with the number of iterations for decoding process. The results in this paper can be applied to the optical CDMA based Laser communication network with multiple access applications

Iterative Decoding for an Optical CDMA based Laser communication System

Energy Technology Data Exchange (ETDEWEB)

Kim, Jin Young; Kim, Eun Cheol [Kwangwoon Univ., Seoul (Korea, Republic of); Cha, Jae Sang [Seoul National Univ. of Technology, Seoul (Korea, Republic of)

2008-11-15

An optical CDMA(code division multiple access)based Laser communication system has attracted much attention since it requires minimal optical Laser signal processing and it is virtually delay free, while from the theoretical point of view, its performance depends on the auto and cross correlation properties of employed sequences. Various kinds of channel coding schemes for optical CDMA based Laser communication systems have been proposed and analyzed to compensate nonideal channel and receiver conditions in impaired photon channels. In this paper, we propose and analyze an iterative decoding of optical CDMA based Laser communication signals for both shot noise limited and thermal noise limited systems. It is assumed that optical channel is an intensity modulated (IM)channel and direct detection scheme is employed to detect the received optical signal. The performance is evaluated in terms of bit error probability and throughput. It is demonstrated that the BER and throughput performance is substantially improved with interleaver length for a fixed code rate and with alphabet size of PPM (pulse position modulation). Also, the BER and throughput performance is significantly enhanced with the number of iterations for decoding process. The results in this paper can be applied to the optical CDMA based Laser communication network with multiple access applications.

Design and performance analysis for several new classes of codes for optical synchronous CDMA and for arbitrary-medium time-hopping synchronous CDMA communication systems

Science.gov (United States)

Kostic, Zoran; Titlebaum, Edward L.

1994-08-01

New families of spread-spectrum codes are constructed, that are applicable to optical synchronous code-division multiple-access (CDMA) communications as well as to arbitrary-medium time-hopping synchronous CDMA communications. Proposed constructions are based on the mappings from integer sequences into binary sequences. We use the concept of number theoretic quadratic congruences and a subset of Reed-Solomon codes similar to the one utilized in the Welch-Costas frequency-hop (FH) patterns. The properties of the codes are as good as or better than the properties of existing codes for synchronous CDMA communications: Both the number of code-sequences within a single code family and the number of code families with good properties are significantly increased when compared to the known code designs. Possible applications are presented. To evaluate the performance of the proposed codes, a new class of hit arrays called cyclical hit arrays is recalled, which give insight into the previously unknown properties of the few classes of number theoretic FH patterns. Cyclical hit arrays and the proposed mappings are used to determine the exact probability distribution functions of random variables that represent interference between users of a time-hopping or optical CDMA system. Expressions for the bit error probability in multi-user CDMA systems are derived as a function of the number of simultaneous CDMA system users, the length of signature sequences and the threshold of a matched filter detector. The performance results are compared with the results for some previously known codes.

Generalized Multicarrier CDMA: Unification and Linear Equalization

Directory of Open Access Journals (Sweden)

Wang Zhengdao

2005-01-01

Full Text Available Relying on block-symbol spreading and judicious design of user codes, this paper builds on the generalized multicarrier (GMC quasisynchronous CDMA system that is capable of multiuser interference (MUI elimination and intersymbol interference (ISI suppression with guaranteed symbol recovery, regardless of the wireless frequency-selective channels. GMC-CDMA affords an all-digital unifying framework, which encompasses single-carrier and several multicarrier (MC CDMA systems. Besides the unifying framework, it is shown that GMC-CDMA offers flexibility both in full load (maximum number of users allowed by the available bandwidth and in reduced load settings. A novel blind channel estimation algorithm is also derived. Analytical evaluation and simulations illustrate the superior error performance and flexibility of uncoded GMC-CDMA over competing MC-CDMA alternatives especially in the presence of uplink multipath channels.

Time of Arrival Estimation in Probability-Controlled Generalized CDMA Systems

Directory of Open Access Journals (Sweden)

Hagit Messer

2007-11-01

Full Text Available In recent years, more and more wireless communications systems are required to provide also a positioning measurement. In code division multiple access (CDMA communication systems, the positioning accuracy is significantly degraded by the multiple access interference (MAI caused by other users in the system. This MAI is commonly managed by a power control mechanism, and yet, MAI has a major effect on positioning accuracy. Probability control is a recently introduced interference management mechanism. In this mechanism, a user with excess power chooses not to transmit some of its symbols. The information in the nontransmitted symbols is recovered by an error-correcting code (ECC, while all other users receive a more reliable data during these quiet periods. Previous research had shown that the implementation of a probability control mechanism can significantly reduce the MAI. In this paper, we show that probability control also improves the positioning accuracy. We focus on time-of-arrival (TOA based positioning systems. We analyze the TOA estimation performance in a generalized CDMA system, in which the probability control mechanism is employed, where the transmitted signal is noncontinuous with a symbol transmission probability smaller than 1. The accuracy of the TOA estimation is determined using appropriate modifications of the Cramer-Rao bound on the delay estimation. Keeping the average transmission power constant, we show that the TOA accuracy of each user does not depend on its transmission probability, while being a nondecreasing function of the transmission probability of any other user. Therefore, a generalized, noncontinuous CDMA system with a probability control mechanism can always achieve better positioning performance, for all users in the network, than a conventional, continuous, CDMA system.

CDMA

International Nuclear Information System (INIS)

Ock, Yun Cheol

2003-07-01

This book is comprised of summary of mobile communication : CT, TRS, Cellular mobile communication, digital communication, Is-95 and Friedns and PCS system, Basic concept : tools of mathematics, system, signal analysis of Fourier, Sampling, DB and Bandwidth, noise and OSI 7 Layer, DSSS and Code theory : spread spectrum, CDM/CDMA communication mode, code theory and PN code, CDMA Demodulator : Searcher engine, function by searcher engine, Finger demodulator and searcher task, control power : the reason for forward control power and reverse control power, open loop power control, closed loop power control and outer loop power control, Hand off : Parameter for hand off MASHO, new soft hand off, hard hand off, MAHHO and Access hand off, Radio transmission technique : interleaving and Modulation, Is-95, COMA 2000 : COMA 2000 System, Idle state and registration, vocoder : voice source coding and QCELP

MC-DS-CDMA System based on DWT and STBC in ITU Multipath Fading Channels Model

Directory of Open Access Journals (Sweden)

Nader Abdullah Khadam

2018-03-01

Full Text Available In this paper, the performance of multicarrier direct sequence code division multiple access (MC-DS-CDMA in fixed MC-DS-CDMA and Mobile MC-DS-CDMA applications have been improved by using the compensations of space time block coding and Discrete Fast Fourier transforms (FFT or Discrete Wavelets transform DWT. These MC-DS-CDMA systems had been simulated using MATLAB 2015a. Through simulation of the proposed system, various parameters can be changed and tested. The Bit Error Rate (BERs of these systems are obtained over wide range of signal to noise ratio. All simulation results had been compared with each other using different subcarrier size of FFT or DWT with STBC for 1,2,3 and 4 antennas in transmitter and under different ITU multipath fading channels and different Doppler frequencies (fd. The proposed structures of STBC-MC-DS-CDMA system based on (DWT batter than based on (FFT in varies Doppler frequencies and subcarrier size. Also, proposed system with STBC based on 4 transmitters better than other systems based on 1 or 2 or 3 transmitters in all Doppler frequencies and subcarrier size in all simulation results.

Channel coding for underwater acoustic single-carrier CDMA communication system

Science.gov (United States)

Liu, Lanjun; Zhang, Yonglei; Zhang, Pengcheng; Zhou, Lin; Niu, Jiong

2017-01-01

CDMA is an effective multiple access protocol for underwater acoustic networks, and channel coding can effectively reduce the bit error rate (BER) of the underwater acoustic communication system. For the requirements of underwater acoustic mobile networks based on CDMA, an underwater acoustic single-carrier CDMA communication system (UWA/SCCDMA) based on the direct-sequence spread spectrum is proposed, and its channel coding scheme is studied based on convolution, RA, Turbo and LDPC coding respectively. The implementation steps of the Viterbi algorithm of convolutional coding, BP and minimum sum algorithms of RA coding, Log-MAP and SOVA algorithms of Turbo coding, and sum-product algorithm of LDPC coding are given. An UWA/SCCDMA simulation system based on Matlab is designed. Simulation results show that the UWA/SCCDMA based on RA, Turbo and LDPC coding have good performance such that the communication BER is all less than 10-6 in the underwater acoustic channel with low signal to noise ratio (SNR) from -12 dB to -10dB, which is about 2 orders of magnitude lower than that of the convolutional coding. The system based on Turbo coding with Log-MAP algorithm has the best performance.

A unifying paradigm for IS-95 CDMA system

Energy Technology Data Exchange (ETDEWEB)

Lee, K.R.; Kim, H.J.; Kim, W.K. [Korea University, Seoul (Korea, Republic of)

1997-05-01

An important method of generating binary sequences is by means of a shift register (SR) configuration such as Linear Feedback Shift Register (LFSR). The SR configuration is used for CRC, interleaver, convolutional encoder and PN generators in IS-95 CDMA system. In this regard, CRC, interleaver, convolutional encoder can be seen as input-driven configurations, and PN generator can be seen as an autonomous configuration. In this paper we propose some alternative schemes of PN code generator which has the different structure from conventional one. The implementations can be used toward building a single chip that handles most of the signal processing that occur at the front-end of IS-95 CDMA transmission. (author). 5 refs., 5 figs.

Adaptive Space-Time-Spreading-Assisted Wideband CDMA Systems Communicating over Dispersive Nakagami- Fading Channels

Directory of Open Access Journals (Sweden)

Yang Lie-Liang

2005-01-01

Full Text Available In this contribution, the performance of wideband code-division multiple-access (W-CDMA systems using space-time-spreading- (STS- based transmit diversity is investigated, when frequency-selective Nakagami- fading channels, multiuser interference, and background noise are considered. The analysis and numerical results suggest that the achievable diversity order is the product of the frequency-selective diversity order and the transmit diversity order. Furthermore, both the transmit diversity and the frequency-selective diversity have the same order of importance. Since W-CDMA signals are subjected to frequency-selective fading, the number of resolvable paths at the receiver may vary over a wide range depending on the transmission environment encountered. It can be shown that, for wireless channels where the frequency selectivity is sufficiently high, transmit diversity may be not necessitated. Under this case, multiple transmission antennas can be leveraged into an increased bitrate. Therefore, an adaptive STS-based transmission scheme is then proposed for improving the throughput of W-CDMA systems. Our numerical results demonstrate that this adaptive STS-based transmission scheme is capable of significantly improving the effective throughput of W-CDMA systems. Specifically, the studied W-CDMA system's bitrate can be increased by a factor of three at the modest cost of requiring an extra 0.4 dB or 1.2 dB transmitted power in the context of the investigated urban or suburban areas, respectively.

Rotated Walsh-Hadamard Spreading with Robust Channel Estimation for a Coded MC-CDMA System

Directory of Open Access Journals (Sweden)

Raulefs Ronald

2004-01-01

Full Text Available We investigate rotated Walsh-Hadamard spreading matrices for a broadband MC-CDMA system with robust channel estimation in the synchronous downlink. The similarities between rotated spreading and signal space diversity are outlined. In a multiuser MC-CDMA system, possible performance improvements are based on the chosen detector, the channel code, and its Hamming distance. By applying rotated spreading in comparison to a standard Walsh-Hadamard spreading code, a higher throughput can be achieved. As combining the channel code and the spreading code forms a concatenated code, the overall minimum Hamming distance of the concatenated code increases. This asymptotically results in an improvement of the bit error rate for high signal-to-noise ratio. Higher convolutional channel code rates are mostly generated by puncturing good low-rate channel codes. The overall Hamming distance decreases significantly for the punctured channel codes. Higher channel code rates are favorable for MC-CDMA, as MC-CDMA utilizes diversity more efficiently compared to pure OFDMA. The application of rotated spreading in an MC-CDMA system allows exploiting diversity even further. We demonstrate that the rotated spreading gain is still present for a robust pilot-aided channel estimator. In a well-designed system, rotated spreading extends the performance by using a maximum likelihood detector with robust channel estimation at the receiver by about 1 dB.

Bit Error Rate Analysis for MC-CDMA Systems in Nakagami- Fading Channels

Directory of Open Access Journals (Sweden)

Li Zexian

2004-01-01

Full Text Available Multicarrier code division multiple access (MC-CDMA is a promising technique that combines orthogonal frequency division multiplexing (OFDM with CDMA. In this paper, based on an alternative expression for the -function, characteristic function and Gaussian approximation, we present a new practical technique for determining the bit error rate (BER of multiuser MC-CDMA systems in frequency-selective Nakagami- fading channels. The results are applicable to systems employing coherent demodulation with maximal ratio combining (MRC or equal gain combining (EGC. The analysis assumes that different subcarriers experience independent fading channels, which are not necessarily identically distributed. The final average BER is expressed in the form of a single finite range integral and an integrand composed of tabulated functions which can be easily computed numerically. The accuracy of the proposed approach is demonstrated with computer simulations.

BER Performance Simulation of Generalized MC DS-CDMA System with Time-Limited Blackman Chip Waveform

Directory of Open Access Journals (Sweden)

I. Develi

2010-09-01

Full Text Available Multiple access interference encountered in multicarrier direct sequence-code division multiple access (MC DS-CDMA is the most important difficulty that depends mainly on the correlation properties of the spreading sequences as well as the shape of the chip waveforms employed. In this paper, bit error rate (BER performance of the generalized MC DS-CDMA system that employs time-limited Blackman chip waveform is presented for Nakagami-m fading channels. Simulation results show that the use of Blackman chip waveform can improve the BER performance of the generalized MC DS-CDMA system, as compared to the performances achieved by using timelimited chip waveforms in the literature.

Particle Filtering for Multiple Access DS/CDMA Systems DS/CDMA Channel Estimation

Directory of Open Access Journals (Sweden)

Rafael Oliveira Ribeiro

2013-09-01

Full Text Available This article discusses computational implementation aspects and performance of a Bayesian methodology, namely particle filter (PF. The PF channel estimation technique is directly applied to the channel coefficients estimation of DS/CDMA systems. Simulation results for non-line-of-sight (NLOS Rayleigh fading channel propagation have indicated that the bootstrap PF estimator is capable to provide RMSE in the range of [10-3 ; 10-2] for a wide range of multiple access interference (MAI levels and signal-noise ratio (SNR, and still be able to offer robustness to near-far ratio (NFR effect.

Comparison and classification of all-optical CDMA systems for future telecommunication networks

Science.gov (United States)

Iversen, Kay; Hampicke, Dirk

1995-12-01

This paper shows the state of the art in fiber optical code-division multiple-access (CDMA). Recent work in this area for both, systems and sequences is reviewed and analyzed. For that purpose a classification of systems, corresponding to the manner of signal processing and a classification of known (0,1)-sequences are presented. It is shown that due to the limits by currently available device technology especially two techniques are promising for implementation in broadband telecommunication networks: spectral encoding with integrated optical filters and CDMA in combination with wavelength multiple access schemes. Further an overview about some important experiments in this field is given.

W-CDMA Uplink Capacity and Interference Statistics of a LongGroove-Shaped Road Microcells Using A Hybrid Propagation Model

Directory of Open Access Journals (Sweden)

L. de Haro-Ariet

2003-09-01

Full Text Available The uplink capacity and the interference statistics of the sectorsof a long groove-shaped road W-CDMA microcell are studied. A model of 9microcells in a groove-shaped road is used to analyze the uplink. Ahybrid model for the propagation is used in the analysis. The capacityand the interference statistics of the cell are studied for differentsector ranges, different specific attenuation factors, differentantenna side lobe levels and different bend losses.

Performance of Generalized Multicarrier DS-CDMA over Nakagami-$m$ Fading Channels

OpenAIRE

Yang, L-L.; Hanzo, L.

2002-01-01

A class of generalized multicarrier direct sequence code-division multiple-access (MC DS-CDMA) schemes is defined and its performance is considered over multipath Nakagamifading channels. The spacing between two adjacent subcarriers of the generalized MC DS-CDMA is a variable, allowing us to gain insight into the effects of the spacing on the bit error rate (BER) performance of MC DS-CDMA systems. This generalized MC DS-CDMA scheme includes the subclasses of multitone DS-CDMA and orthogonal M...

Optical CDMA and WDMA in the access network

Science.gov (United States)

Sargent, Edward H.; Stok, Andrew

2003-08-01

Optical CDMA provides one avenue to sharing the vast bandwidth of optical fiber among a number of active users in a network. In this work we address two questions central to considering the areas of applicability of CDMA in optics: (1) How do we compare fairly optical CDMA codes of different families, and what do we conclude? (2) How do we compare optical CDMA performance with that of conventional optical WDMA? To answer the first question, we present a method of comparing optical CDMA codes of different families, sizes and weights. We outline why the traditional performance metric of bit-error rate versus number of simultaneous users is lacking and propose a different performance measure -- the peak throughput normalized with respect to the size of the code. This metric is used to show that optical-orthogonal codes (OOCs) with a weight of 4 perform best at low offered loads while OOCs with weight 5 should be used at higher offered loads. By applying the technique across different families of codes, we demonstrate that multi-wavelength OOCs (MWOOCs) perform better than both OOCs (by a factor of approximately 1.25) and asymmetric prime-hop codes (by a factor of approximately 3.5), over a wide range of offered loads. In answer to the second question, we present a comparison of the performance of optical code-division multiple-access (CDMA) systems with that of a wavelength-division multiple-access (WDMA) system. The multiple-access techniques are applied in a time-slotted broadcast local-area network. The utilization, defined as the throughput per unit of time-domain bandwidth expansion, and packet delay are used as metrics of performance. When more than seven wavelengths are available, optical CDMA systems using asymmetric prime-hop codes and all-optical signal processing are shown to have higher peak utilization and lower corresponding delay than a WDMA system with the same number of wavelengths. When the encoders/decoders operate at the chip rate, the utilization

Multiple Access Interference Reduction Using Received Response Code Sequence for DS-CDMA UWB System

Science.gov (United States)

Toh, Keat Beng; Tachikawa, Shin'ichi

This paper proposes a combination of novel Received Response (RR) sequence at the transmitter and a Matched Filter-RAKE (MF-RAKE) combining scheme receiver system for the Direct Sequence-Code Division Multiple Access Ultra Wideband (DS-CDMA UWB) multipath channel model. This paper also demonstrates the effectiveness of the RR sequence in Multiple Access Interference (MAI) reduction for the DS-CDMA UWB system. It suggests that by using conventional binary code sequence such as the M sequence or the Gold sequence, there is a possibility of generating extra MAI in the UWB system. Therefore, it is quite difficult to collect the energy efficiently although the RAKE reception method is applied at the receiver. The main purpose of the proposed system is to overcome the performance degradation for UWB transmission due to the occurrence of MAI during multiple accessing in the DS-CDMA UWB system. The proposed system improves the system performance by improving the RAKE reception performance using the RR sequence which can reduce the MAI effect significantly. Simulation results verify that significant improvement can be obtained by the proposed system in the UWB multipath channel models.

DS-CDMA system outer loop power control and improvement for multi-service

Institute of Scientific and Technical Information of China (English)

Guan Mingxiang; Guo Qing; Li Xing

2008-01-01

When a new user accesses the CDMA system, the load will change drastically, and therefore, the advanced outer loop power control (OLPC) technology has to be adopted to enrich the target signal interference ratio (SIR) and improve the system performance. The existing problems about DS-CDMA outer loop power control for multi-service are introduced and the power control theoretical model is analyzed. System simulation is adopted on how to obtain the theoretical performance and parameter optimization of the power control algorithm. The OLPC algorithm is improved and the performance comparisons between the old algorithm and the improved algorithm are given. The results show good performance of the improved OLPC algorithm and prove the validity of the improved method for multi-service.

Uplink Packet-Data Scheduling in DS-CDMA Systems

Science.gov (United States)

Choi, Young Woo; Kim, Seong-Lyun

In this letter, we consider the uplink packet scheduling for non-real-time data users in a DS-CDMA system. As an effort to jointly optimize throughput and fairness, we formulate a time-span minimization problem incorporating the time-multiplexing of different simultaneous transmission schemes. Based on simple rules, we propose efficient scheduling algorithms and compare them with the optimal solution obtained by linear programming.

An Efficient Code-Timing Estimator for DS-CDMA Systems over Resolvable Multipath Channels

Directory of Open Access Journals (Sweden)

Jian Li

2005-04-01

Full Text Available We consider the problem of training-based code-timing estimation for the asynchronous direct-sequence code-division multiple-access (DS-CDMA system. We propose a modified large-sample maximum-likelihood (MLSML estimator that can be used for the code-timing estimation for the DS-CDMA systems over the resolvable multipath channels in closed form. Simulation results show that MLSML can be used to provide a high correct acquisition probability and a high estimation accuracy. Simulation results also show that MLSML can have very good near-far resistant capability due to employing a data model similar to that for adaptive array processing where strong interferences can be suppressed.

High-Performance Wireless via the Merger of CI Chip-Shaped DS-CDMA and Oscillating-Beam Smart Antenna Arrays

Directory of Open Access Journals (Sweden)

Nassar Carl R

2004-01-01

Full Text Available We introduce a novel merger of direct sequence code division multiple access (DS-CDMA and smart antenna arrays. With regard to the DS-CDMA scheme, we employ carrier interferometry DS-CDMA (CI/DS-CDMA, a novel implementation of DS-CDMA where chips are decomposable into narrowband frequency components. With regard to the antenna array, we deploy the oscillating-beam smart array. Here, applying proper time-varying phases to the array elements, we create small movement (oscillation in the antenna array's pattern, while steering the antenna pattern main lobe to the position of the intended user. The oscillating antenna pattern creates a time-varying channel with a controllable coherence time. This, in turn, provides transmit diversity in the form of a time diversity gain at the mobile receiver side. At the receiver, three stages of combining are available: combining time components of the received signal within symbol duration (each experiencing a different fade to enhance performance via time diversity; combining frequency components which make up the CI/DS-CDMA chip to enhance the performance via frequency diversity; and combining across chips to eliminate the interfering users on the system. Merging CI/DS-CDMA with the oscillating-beam smart antenna at the base station, we achieve very high capacity via the merger of SDMA (available through directionality of the antenna array and code division multiple access (inherent in CI/DS-CDMA, and very high performance via the construction of receivers that exploit both transmit diversity and frequency diversity. We present the performance gains of the proposed merger.

Performance of DS-CDMA systems with optimal hard-decision parallel interference cancellation

NARCIS (Netherlands)

Hofstad, van der R.W.; Klok, M.J.

2003-01-01

We study a multiuser detection system for code-division multiple access (CDMA). We show that applying multistage hard-decision parallel interference cancellation (HD-PIC) significantly improves performance compared to the matched filter system. In (multistage) HD-PIC, estimates of the interfering

Multimedia transmission in MC-CDMA using adaptive subcarrier power allocation and CFO compensation

Science.gov (United States)

Chitra, S.; Kumaratharan, N.

2018-02-01

Multicarrier code division multiple access (MC-CDMA) system is one of the most effective techniques in fourth-generation (4G) wireless technology, due to its high data rate, high spectral efficiency and resistance to multipath fading. However, MC-CDMA systems are greatly deteriorated by carrier frequency offset (CFO) which is due to Doppler shift and oscillator instabilities. It leads to loss of orthogonality among the subcarriers and causes intercarrier interference (ICI). Water filling algorithm (WFA) is an efficient resource allocation algorithm to solve the power utilisation problems among the subcarriers in time-dispersive channels. The conventional WFA fails to consider the effect of CFO. To perform subcarrier power allocation with reduced CFO and to improve the capacity of MC-CDMA system, residual CFO compensated adaptive subcarrier power allocation algorithm is proposed in this paper. The proposed technique allocates power only to subcarriers with high channel to noise power ratio. The performance of the proposed method is evaluated using random binary data and image as source inputs. Simulation results depict that the bit error rate performance and ICI reduction capability of the proposed modified WFA offered superior performance in both power allocation and image compression for high-quality multimedia transmission in the presence of CFO and imperfect channel state information conditions.

Optimal resource allocation in downlink CDMA wireless networks

NARCIS (Netherlands)

Endrayanto, A.I.

2013-01-01

This thesis presents a full analytical characterization of the optimal joint downlink rate and power assignment for maximal total system throughput in a multi cell CDMA network. In Chapter 2, we analyze the feasibility of downlink power assignment in a linear model of two CDMA cell, under the

Adaptive Multiuser Detectors for DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Paul Jean Etienne Jeszensky

2006-02-01

Full Text Available This work makes a review of the main Adaptives Multi-user Detectors (MuD-Adpt for Direct Sequence - Code Division Multiple Access (DS-CDMA systems. The MuD-Adpt based on Minimum Mean Square Error (MMSE and Decorrelator (MuD-Dec are focused. Multi-user detectors show great resistance to the near-far effect and combat effectively the Multiple Access Interference (MAI. Comparative numeric results characterize the substantial performance improvement of those detectors in relation to the matched filter conventional receiver (Conv.

An Iterative Multiuser Detector for Turbo-Coded DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Takawira Fambirai

2005-01-01

Full Text Available We propose an iterative multiuser detector for turbo-coded synchronous and asynchronous direct-sequence CDMA (DS-CDMA systems. The receiver is derived from the maximum a posteriori (MAP estimation of the single user's transmitted data, conditioned on information about the estimate of the multiple-access interference (MAI and the received signal from the channel. This multiple-access interference is reconstructed by making hard decisions on the users' detected bits at the preceding iteration. The complexity of the proposed receiver increases linearly with the number of users. The proposed detection scheme is compared with a previously developed one. The multiuser detector proposed in this paper has a better performance when the transmitted powers of all active users are equal in the additive white Gaussian noise (AWGN channel. Also, the detector is found to be resilient against the near-far effect.

A CDMA Spotbeam Architecture for the Next Generation Satellite System (NGSS) for the Aeronautical Telecommunications Network (ATN)

Science.gov (United States)

Raghavan, Rajesh S.; Shamma, Mohammed A.

2003-01-01

This paper will present work being done to model and simulate a CDMA based Mobile Satellite System architecture for providing all or part of the future Air Traffic Management (ATM) services. Such a system, will help in relieving the dependence on ground based networks, if not eliminate it. Additionally such an architecture can be used in parallel or as a supplementary service along with ground based links to help alleviate any capacity bottlenecks, or in areas where such services are difficult to make available such as in oceanic, remote areas outside the jet highways, or in developing countries where ground services are less available.

Space-Time Coded MC-CDMA: Blind Channel Estimation, Identifiability, and Receiver Design

Directory of Open Access Journals (Sweden)

Li Hongbin

2002-01-01

Full Text Available Integrating the strengths of multicarrier (MC modulation and code division multiple access (CDMA, MC-CDMA systems are of great interest for future broadband transmissions. This paper considers the problem of channel identification and signal combining/detection schemes for MC-CDMA systems equipped with multiple transmit antennas and space-time (ST coding. In particular, a subspace based blind channel identification algorithm is presented. Identifiability conditions are examined and specified which guarantee unique and perfect (up to a scalar channel estimation when knowledge of the noise subspace is available. Several popular single-user based signal combining schemes, namely the maximum ratio combining (MRC and the equal gain combining (EGC, which are often utilized in conventional single-transmit-antenna based MC-CDMA systems, are extended to the current ST-coded MC-CDMA (STC-MC-CDMA system to perform joint combining and decoding. In addition, a linear multiuser minimum mean-squared error (MMSE detection scheme is also presented, which is shown to outperform the MRC and EGC at some increased computational complexity. Numerical examples are presented to evaluate and compare the proposed channel identification and signal detection/combining techniques.

Coding Across Multicodes and Time in CDMA Systems Employing MMSE Multiuser Detector

Directory of Open Access Journals (Sweden)

Park Jeongsoon

2004-01-01

Full Text Available When combining a multicode CDMA system with convolutional coding, two methods have been considered in the literature. In one method, coding is across time in each multicode channel while in the other the coding is across both multicodes and time. In this paper, a performance/complexity analysis of decoding metrics and trellis structures for the two schemes is carried out. It is shown that the latter scheme can exploit the multicode diversity inherent in convolutionally coded direct sequence code division multiple access (DS-CDMA systems which employ minimum mean squared error (MMSE multiuser detectors. In particular, when the MMSE detector provides sufficiently different signal-to-interference ratios (SIRs for the multicode channels, coding across multicodes and time can obtain significant performance gain over coding across time, with nearly the same decoding complexity.

A Unified Approach to the Analysis of Multicarrier DS-CDMA over Nakagami-$M$ Fading Channels

OpenAIRE

Yang, L-L.; Hanzo, L.

2001-01-01

A class of unified multicarrier DS-CDMA (MC DS-CDMA) schemes is defined and its performance is considered over multipath Nakagami-$M$ fading channels. The spacing between two adjacent subcarriers of the unified MC DS-CDMA scheme is a variable, allowing us to gain insight into the effects of the spacing on the bit error rate (BER) performance of MC DS-CDMA systems. This unified MC DS-CDMA scheme includes the subclasses of multitone DS-CDMA and orthogonal MC DS-CDMA as special cases. The optimu...

Robust MOE Detector for DS-CDMA Systems with Signature Waveform Mismatch

Science.gov (United States)

Lin, Tsui-Tsai

In this letter, a decision-directed MOE detector with excellent robustness against signature waveform mismatch is proposed for DS-CDMA systems. Both the theoretic analysis and computer simulation results demonstrate that the proposed detector can provide better SINR performance than that of conventional detectors.

High performance mixed optical CDMA system using ZCC code and multiband OFDM

Directory of Open Access Journals (Sweden)

Nawawi N. M.

2017-01-01

Full Text Available In this paper, we have proposed a high performance network design, which is based on mixed optical Code Division Multiple Access (CDMA system using Zero Cross Correlation (ZCC code and multiband Orthogonal Frequency Division Multiplexing (OFDM called catenated OFDM. In addition, we also investigate the related changing parameters such as; effective power, number of user, number of band, code length and code weight. Then we theoretically analyzed the system performance comprehensively while considering up to five OFDM bands. The feasibility of the proposed system architecture is verified via the numerical analysis. The research results demonstrated that our developed modulation solution can significantly enhanced the total number of user; improving up to 80% for five catenated bands compared to traditional optical CDMA system, with the code length equals to 80, transmitted at 622 Mbps. It is also demonstrated that the BER performance strongly depends on number of weight, especially with less number of users. As the number of weight increases, the BER performance is better.

High performance mixed optical CDMA system using ZCC code and multiband OFDM

Science.gov (United States)

Nawawi, N. M.; Anuar, M. S.; Junita, M. N.; Rashidi, C. B. M.

2017-11-01

In this paper, we have proposed a high performance network design, which is based on mixed optical Code Division Multiple Access (CDMA) system using Zero Cross Correlation (ZCC) code and multiband Orthogonal Frequency Division Multiplexing (OFDM) called catenated OFDM. In addition, we also investigate the related changing parameters such as; effective power, number of user, number of band, code length and code weight. Then we theoretically analyzed the system performance comprehensively while considering up to five OFDM bands. The feasibility of the proposed system architecture is verified via the numerical analysis. The research results demonstrated that our developed modulation solution can significantly enhanced the total number of user; improving up to 80% for five catenated bands compared to traditional optical CDMA system, with the code length equals to 80, transmitted at 622 Mbps. It is also demonstrated that the BER performance strongly depends on number of weight, especially with less number of users. As the number of weight increases, the BER performance is better.

Cross-Layer Design and Analysis of Downlink Communications in Cellular CDMA Systems

Directory of Open Access Journals (Sweden)

Sun Jin Yuan

2006-01-01

Full Text Available A cellular CDMA network with voice and data communications is considered. Focusing on the downlink direction, we seek for the overall performance improvement which can be achieved by cross-layer analysis and design, taking physical layer, link layer, network layer, and transport layer into account. We are concerned with the role of each single layer as well as the interaction among layers, and propose algorithms/schemes accordingly to improve the system performance. These proposals include adaptive scheduling for link layer, priority-based handoff strategy for network admission control, and an algorithm for the avoidance of TCP spurious timeouts at the transport layer. Numerical results show the performance gain of each proposed scheme over independent performance of an individual layer in the wireless mobile network. We conclude that the system performance in terms of capacity, throughput, dropping probability, outage, power efficiency, delay, and fairness can be enhanced by jointly considering the interactions across layers.

Bit Error Rate Performance of a MIMO-CDMA System Employing Parity-Bit-Selected Spreading in Frequency Nonselective Rayleigh Fading

Directory of Open Access Journals (Sweden)

Claude D'Amours

2011-01-01

Full Text Available We analytically derive the upper bound for the bit error rate (BER performance of a single user multiple input multiple output code division multiple access (MIMO-CDMA system employing parity-bit-selected spreading in slowly varying, flat Rayleigh fading. The analysis is done for spatially uncorrelated links. The analysis presented demonstrates that parity-bit-selected spreading provides an asymptotic gain of 10log(Nt dB over conventional MIMO-CDMA when the receiver has perfect channel estimates. This analytical result concurs with previous works where the (BER is determined by simulation methods and provides insight into why the different techniques provide improvement over conventional MIMO-CDMA systems.

DS-CDMA satellite diversity reception for personal satellite communication: Downlink performance analysis

Science.gov (United States)

DeGaudenzi, Riccardo; Giannetti, Filippo

1995-01-01

The downlink of a satellite-mobile personal communication system employing power-controlled Direct Sequence Code Division Multiple Access (DS-CDMA) and exploiting satellite-diversity is analyzed and its performance compared with a more traditional communication system utilizing single satellite reception. The analytical model developed has been thoroughly validated by means of extensive Monte Carlo computer simulations. It is shown how the capacity gain provided by diversity reception shrinks considerably in the presence of increasing traffic or in the case of light shadowing conditions. Moreover, the quantitative results tend to indicate that to combat system capacity reduction due to intra-system interference, no more than two satellites shall be active over the same region. To achieve higher system capacity, differently from terrestrial cellular systems, Multi-User Detection (MUD) techniques are likely to be required in the mobile user terminal, thus considerably increasing its complexity.

The Effects of Spatial Diversity and Imperfect Channel Estimation on Wideband MC-DS-CDMA and MC-CDMA

Science.gov (United States)

2009-10-01

In our previous work, we compared the theoretical bit error rates of multi-carrier direct sequence code division multiple access (MC- DS - CDMA ) and...consider only those cases where MC- CDMA has higher frequency diversity than MC- DS - CDMA . Since increases in diversity yield diminishing gains, we conclude

Interference Cancellation Technique Based on Discovery of Spreading Codes of Interference Signals and Maximum Correlation Detection for DS-CDMA System

Science.gov (United States)

Hettiarachchi, Ranga; Yokoyama, Mitsuo; Uehara, Hideyuki

This paper presents a novel interference cancellation (IC) scheme for both synchronous and asynchronous direct-sequence code-division multiple-access (DS-CDMA) wireless channels. In the DS-CDMA system, the multiple access interference (MAI) and the near-far problem (NFP) are the two factors which reduce the capacity of the system. In this paper, we propose a new algorithm that is able to detect all interference signals as an individual MAI signal by maximum correlation detection. It is based on the discovery of all the unknowing spreading codes of the interference signals. Then, all possible MAI patterns so called replicas are generated as a summation of interference signals. And the true MAI pattern is found by taking correlation between the received signal and the replicas. Moreover, the receiver executes MAI cancellation in a successive manner, removing all interference signals by single-stage. Numerical results will show that the proposed IC strategy, which alleviates the detrimental effect of the MAI and the near-far problem, can significantly improve the system performance. Especially, we can obtain almost the same receiving characteristics as in the absense of interference for asynchrnous system when received powers are equal. Also, the same performances can be seen under any received power state for synchronous system.

Multichannel Baseband Processor for Wideband CDMA

Science.gov (United States)

Jalloul, Louay M. A.; Lin, Jim

2005-12-01

The system architecture of the cellular base station modem engine (CBME) is described. The CBME is a single-chip multichannel transceiver capable of processing and demodulating signals from multiple users simultaneously. It is optimized to process different classes of code-division multiple-access (CDMA) signals. The paper will show that through key functional system partitioning, tightly coupled small digital signal processing cores, and time-sliced reuse architecture, CBME is able to achieve a high degree of algorithmic flexibility while maintaining efficiency. The paper will also highlight the implementation and verification aspects of the CBME chip design. In this paper, wideband CDMA is used as an example to demonstrate the architecture concept.

A General Model for Performance Evaluation in DS-CDMA Systems with Variable Spreading Factors

Science.gov (United States)

Chiaraluce, Franco; Gambi, Ennio; Righi, Giorgia

This paper extends previous analytical approaches for the study of CDMA systems to the relevant case of multipath environments where users can operate at different bit rates. This scenario is of interest for the Wideband CDMA strategy employed in UMTS, and the model permits the performance comparison of classic and more innovative spreading signals. The method is based on the characteristic function approach, that allows to model accurately the various kinds of interferences. Some numerical examples are given with reference to the ITU-R M. 1225 Recommendations, but the analysis could be extended to different channel descriptions.

Theoretical analysis and simulation of a code division multiple access system (cdma for secure signal transmission in wideband channels

Directory of Open Access Journals (Sweden)

Stevan M. Berber

2014-06-01

Full Text Available Chaotic spreading sequences can increase secrecy and resistance to interception in signal transmission. Chaos-based CDMA systems have been well investigated in the case of flat fading and noise presence in the channel. However, these systems operating in wideband channels, characterized by the frequency selective fading and white Gaussian noise, have not been investigated to the level of understanding their practical applications. This paper presents a detailed mathematical model of a CDMA system based on chaotic spreading sequences. In a theoretical analysis, all signals are represented in the discrete time domain. Using the theory of discrete time stochastic processes, the probability of error expressions are derived in a closed form for a multi-user chaos based CDMA system. For the sake of comparison, the expressions for the probability of error are derived separately for narrowband and wideband channels. The application of the system interleaving technique is investigated in particular, which showed that this technique can substantially improve probability of error in the system.  The system is simulated and the findings of the simulation confirmed theoretically expected results. Possible improvements in the probability of bit error due to multipath channel nature, with and without interleavers, are quantified depending on the random delay and the number of users in the system. In the analyzed system, a simplified version of the wideband channel model, proposed for modern wideband wireless networks, is used. Introduction Over the past years, the demand for wireless communications has increased substantially due to advancements in mobile communication systems and networks. Following these increasing demands, modern communication systems require the ability to handle a large number of users to process and transmit wideband signals through complex frequency selective channels. One of the techniques for transmission of multi-user signals is the

Load control strategies in 2G mobile network for W-CDMA radio ...

African Journals Online (AJOL)

Network planning requires a faithful analysis of each individual cell's capacity. In this paper, we examine load control equations as a resource allocation tool to analyse cell capacity for the uplink and downlink of Wideband Code Division Multiple Access (W-CDMA) networks. In the uplink, the noise rise is a parameter of ...

Delay Estimation in Long-Code Asynchronous DS/CDMA Systems Using Multiple Antennas

Directory of Open Access Journals (Sweden)

Sirbu Marius

2004-01-01

Full Text Available The problem of propagation delay estimation in asynchronous long-code DS-CDMA multiuser systems is addressed. Almost all the methods proposed so far in the literature for propagation delay estimation are derived for short codes and the knowledge of the codes is exploited by the estimators. In long-code CDMA, the spreading code is aperiodic and the methods developed for short codes may not be used or may increase the complexity significantly. For example, in the subspace-based estimators, the aperiodic nature of the code may require subspace tracking. In this paper we propose a novel method for simultaneous estimation of the propagation delays of several active users. A specific multiple-input multiple-output (MIMO system model is constructed in a multiuser scenario. In such model the channel matrix contains information about both the users propagation delays and channel impulse responses. Consequently, estimates of the delays are obtained as a by-product of the channel estimation task. The channel matrix has a special structure that is exploited in estimating the delays. The proposed delay estimation method lends itself to an adaptive implementation. Thus, it may be applied to joint channel and delay estimation in uplink DS-CDMA analogously to the method presented by the authors in 2003. The performance of the proposed method is studied in simulation using realistic time-varying channel model and different SNR levels in the face of near-far effects, and using low spreading factor (high data rates.

Successive Interference Cancellation for DS-CDMA Systems with Transmit Diversity

Directory of Open Access Journals (Sweden)

Li Wei

2004-01-01

Full Text Available We introduce a new successive interference cancellation (SIC technique for direct sequence code division multiple access (DS-CDMA systems with transmit diversity. The transmit diversity is achieved with a space-time block code (STBC. In our work we first consider hard decision SIC with an STBC, and then investigate the performance of soft decision SIC with an STBC. System performance over a Rayleigh fading channel is investigated and the analysis is confirmed by simulation.

Multichannel Baseband Processor for Wideband CDMA

Directory of Open Access Journals (Sweden)

Jim Lin

2005-07-01

Full Text Available The system architecture of the cellular base station modem engine (CBME is described. The CBME is a single-chip multichannel transceiver capable of processing and demodulating signals from multiple users simultaneously. It is optimized to process different classes of code-division multiple-access (CDMA signals. The paper will show that through key functional system partitioning, tightly coupled small digital signal processing cores, and time-sliced reuse architecture, CBME is able to achieve a high degree of algorithmic flexibility while maintaining efficiency. The paper will also highlight the implementation and verification aspects of the CBME chip design. In this paper, wideband CDMA is used as an example to demonstrate the architecture concept.

Intersystem Interference Reduction for Overlaid HAPS-Terrestrial CDMA System

Science.gov (United States)

Huang, Jeng-Ji; Wang, Wei-Ting; Li, Mingfu; Shiung, David; Ferng, Huei-Wen

In this letter, we propose that directional antennas, combined with power management, be incorporated to reduce intersystem interference in a shared band overlaid high altitude platform station (HAPS)-terrestrial code division multiple access (CDMA) system. To eliminate the HAPS to terrestrial interference, the HAPS is accessed only via directional antennas under the proposed scheme. By doing so, the uplink power to the HAPS can accordingly be increased, so that the terrestrial to HAPS interference is also effectively suppressed.

Multicarrier Block-Spread CDMA for Broadband Cellular Downlink

Directory of Open Access Journals (Sweden)

Leus Geert

2004-01-01

Full Text Available Effective suppression of multiuser interference (MUI and mitigation of frequency-selective fading effects within the complexity constraints of the mobile constitute major challenges for broadband cellular downlink transceiver design. Existing wideband direct-sequence (DS code division multiple access (CDMA transceivers suppress MUI statistically by restoring the orthogonality among users at the receiver. However, they call for receive diversity and multichannel equalization to improve the fading effects caused by deep channel fades. Relying on redundant block spreading and linear precoding, we design a so-called multicarrier block-spread- (MCBS-CDMA transceiver that preserves the orthogonality among users and guarantees symbol detection, regardless of the underlying frequency-selective fading channels. These properties allow for deterministic MUI elimination through low-complexity block despreading and enable full diversity gains, irrespective of the system load. Different options to perform equalization and decoding, either jointly or separately, strike the trade-off between performance and complexity. To improve the performance over multi-input multi-output (MIMO multipath fading channels, our MCBS-CDMA transceiver combines well with space-time block-coding (STBC techniques, to exploit both multiantenna and multipath diversity gains, irrespective of the system load. Simulation results demonstrate the superior performance of MCBS-CDMA compared to competing alternatives.

Maximal Ratio Combining Using Channel Estimation in Chaos Based Pilot-Added DS-CDMA System with Antenna Diversity

Directory of Open Access Journals (Sweden)

Meher Krishna Patel

2017-01-01

Full Text Available This paper presents an adaptive multiuser transceiver scheme for DS-CDMA systems in which pilot symbols are added to users’ data to estimate complex channel fading coefficients. The performance of receiver antenna diversity with maximal ratio combining (MRC technique is analyzed for imperfect channel estimation in flat fading environments. The complex fading coefficients are estimated using least mean square (LMS algorithm and these coefficients are utilized by the maximal ratio combiner for generating the decision variable. Probability of error in closed form is derived. Further, the effect of pilot signal power on bit error rate (BER and BER performance of multiplexed pilot and data signal transmission scenario are investigated. We have compared the performance of added and multiplexed pilot-data systems and concluded the advantages of both systems. The proposed CDMA technique uses the chaotic sequence as spreading sequence. Assuming proper synchronization, the computer simulation results demonstrate the better bit error rate performance in the presence of channel estimator in the chaotic based CDMA system and the receiver antenna diversity technique further improves the performance of the proposed system. Also, no channel estimator is required if there is no phase distortion to the transmitted signal.

Crest Factor Reduction in MC-CDMA Employing Carrier Interferometry Codes

Directory of Open Access Journals (Sweden)

Natarajan Balasubramaniam

2004-01-01

Full Text Available This paper addresses signal compactness issues in MC-CDMA employing carrier interferometry codes using the measure of crest factor (CF. Carrier interferometry codes, applied to N -carrier MC-CDMA systems, enable 2N users to simultaneously share the system bandwidth with minimal degradation in performance (relative to the N -orthogonal-user case. First, for a fully loaded ( K=N and K=2N users MC-CDMA system with practical values of N , it is shown that the CF in downlink transmission demonstrates desirable properties of low mean and low variance. The downlink CF degrades when the number of users in the system decreases. Next, the high CF observed in the uplink is characterized and the poor CF in a partially loaded downlink as well as uplink is effectively combated using Schroeder's analytical CF reduction techniques.

An accurate evaluation of the performance of asynchronous DS-CDMA systems with zero-correlation-zone coding in Rayleigh fading

Science.gov (United States)

Walker, Ernest; Chen, Xinjia; Cooper, Reginald L.

2010-04-01

An arbitrarily accurate approach is used to determine the bit-error rate (BER) performance for generalized asynchronous DS-CDMA systems, in Gaussian noise with Raleigh fading. In this paper, and the sequel, new theoretical work has been contributed which substantially enhances existing performance analysis formulations. Major contributions include: substantial computational complexity reduction, including a priori BER accuracy bounding; an analytical approach that facilitates performance evaluation for systems with arbitrary spectral spreading distributions, with non-uniform transmission delay distributions. Using prior results, augmented by these enhancements, a generalized DS-CDMA system model is constructed and used to evaluated the BER performance, in a variety of scenarios. In this paper, the generalized system modeling was used to evaluate the performance of both Walsh- Hadamard (WH) and Walsh-Hadamard-seeded zero-correlation-zone (WH-ZCZ) coding. The selection of these codes was informed by the observation that WH codes contain N spectral spreading values (0 to N - 1), one for each code sequence; while WH-ZCZ codes contain only two spectral spreading values (N/2 - 1,N/2); where N is the sequence length in chips. Since these codes span the spectral spreading range for DS-CDMA coding, by invoking an induction argument, the generalization of the system model is sufficiently supported. The results in this paper, and the sequel, support the claim that an arbitrary accurate performance analysis for DS-CDMA systems can be evaluated over the full range of binary coding, with minimal computational complexity.

Overloaded CDMA Systems with Displaced Binary Signatures

Directory of Open Access Journals (Sweden)

Vanhaverbeke Frederik

2004-01-01

Full Text Available We extend three types of overloaded CDMA systems, by displacing in time the binary signature sequences of these systems: (1 random spreading (PN, (2 multiple-OCDMA (MO, and (3 PN/OCDMA (PN/O. For each of these systems, we determine the time shifts that minimize the overall multiuser interference power. The achievable channel load with coded and uncoded data is evaluated for the conventional (without displacement and improved (with displacement systems, as well as for systems based on quasi-Welch-bound-equality (QWBE sequences, by means of several types of turbo detectors. For each system, the best performing turbo detector is selected in order to compare the performance of these systems. It is found that the improved systems substantially outperform their original counterparts. With uncoded data, (improved PN/O yields the highest acceptable channel load. For coded data, MO allows for the highest acceptable channel load over all considered systems, both for the conventional and the improved systems. In the latter case, channel loads of about 280% are achievable with a low degradation as compared to a single user system.

Space-Time Chip Equalization for Maximum Diversity Space-Time Block Coded DS-CDMA Downlink Transmission

Directory of Open Access Journals (Sweden)

Petré Frederik

2004-01-01

Full Text Available In the downlink of DS-CDMA, frequency-selectivity destroys the orthogonality of the user signals and introduces multiuser interference (MUI. Space-time chip equalization is an efficient tool to restore the orthogonality of the user signals and suppress the MUI. Furthermore, multiple-input multiple-output (MIMO communication techniques can result in a significant increase in capacity. This paper focuses on space-time block coding (STBC techniques, and aims at combining STBC techniques with the original single-antenna DS-CDMA downlink scheme. This results into the so-called space-time block coded DS-CDMA downlink schemes, many of which have been presented in the past. We focus on a new scheme that enables both the maximum multiantenna diversity and the maximum multipath diversity. Although this maximum diversity can only be collected by maximum likelihood (ML detection, we pursue suboptimal detection by means of space-time chip equalization, which lowers the computational complexity significantly. To design the space-time chip equalizers, we also propose efficient pilot-based methods. Simulation results show improved performance over the space-time RAKE receiver for the space-time block coded DS-CDMA downlink schemes that have been proposed for the UMTS and IS-2000 W-CDMA standards.

Contribution to Synchronization and Tracking Modelisation in a CDMA Receiver

Directory of Open Access Journals (Sweden)

Aicha Alami Hassani

2013-01-01

Full Text Available We propose and analyze a noncoherent receiver with PN code tracking for direct sequence code division multiple access (DS-CDMA communication systems. We employ the delay-lock loop (DLL architectures for the tracking stage. The choice of DLL parameters is studied with special focus on DS-CDMA communication systems and orthogonality conditions. We described the modeling and simulation of the NCO using hardware description language VHDL. Details of the VHDL implementation are shown.

Downlink Multihop Transmission Technique for Asymmetric Traffic Accommodation in DS-CDMA/FDD Cellular Communications

Science.gov (United States)

Mori, Kazuo; Naito, Katsuhiro; Kobayashi, Hideo

This paper proposes an asymmetric traffic accommodation scheme using a multihop transmission technique for CDMA/FDD cellular communication systems. The proposed scheme exploits the multihop transmission to downlink packet transmissions, which require the large transmission power at their single-hop transmissions, in order to increase the downlink capacity. In these multihop transmissions, vacant uplink band is used for the transmissions from relay stations to destination mobile stations, and this leads more capacity enhancement in the downlink communications. The relay route selection method and power control method for the multihop transmissions are also investigated in the proposed scheme. The proposed scheme is evaluated by computer simulation and the results show that the proposed scheme can achieve better system performance.

Computationally Efficient Blind Code Synchronization for Asynchronous DS-CDMA Systems with Adaptive Antenna Arrays

Directory of Open Access Journals (Sweden)

Chia-Chang Hu

2005-04-01

Full Text Available A novel space-time adaptive near-far robust code-synchronization array detector for asynchronous DS-CDMA systems is developed in this paper. There are the same basic requirements that are needed by the conventional matched filter of an asynchronous DS-CDMA system. For the real-time applicability, a computationally efficient architecture of the proposed detector is developed that is based on the concept of the multistage Wiener filter (MWF of Goldstein and Reed. This multistage technique results in a self-synchronizing detection criterion that requires no inversion or eigendecomposition of a covariance matrix. As a consequence, this detector achieves a complexity that is only a linear function of the size of antenna array (J, the rank of the MWF (M, the system processing gain (N, and the number of samples in a chip interval (S, that is, 𝒪(JMNS. The complexity of the equivalent detector based on the minimum mean-squared error (MMSE or the subspace-based eigenstructure analysis is a function of 𝒪((JNS3. Moreover, this multistage scheme provides a rapid adaptive convergence under limited observation-data support. Simulations are conducted to evaluate the performance and convergence behavior of the proposed detector with the size of the J-element antenna array, the amount of the L-sample support, and the rank of the M-stage MWF. The performance advantage of the proposed detector over other DS-CDMA detectors is investigated as well.

Performance of Turbo Interference Cancellation Receivers in Space-Time Block Coded DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Emmanuel Oluremi Bejide

2008-07-01

Full Text Available We investigate the performance of turbo interference cancellation receivers in the space time block coded (STBC direct-sequence code division multiple access (DS-CDMA system. Depending on the concatenation scheme used, we divide these receivers into the partitioned approach (PA and the iterative approach (IA receivers. The performance of both the PA and IA receivers is evaluated in Rayleigh fading channels for the uplink scenario. Numerical results show that the MMSE front-end turbo space-time iterative approach receiver (IA effectively combats the mixture of MAI and intersymbol interference (ISI. To further investigate the possible achievable data rates in the turbo interference cancellation receivers, we introduce the puncturing of the turbo code through the use of rate compatible punctured turbo codes (RCPTCs. Simulation results suggest that combining interference cancellation, turbo decoding, STBC, and RCPTC can significantly improve the achievable data rates for a synchronous DS-CDMA system for the uplink in Rayleigh flat fading channels.

Compensating for Channel Fading in DS-CDMA Communication Systems Employing ICA Neural Network Detectors

Directory of Open Access Journals (Sweden)

David Overbye

2005-06-01

Full Text Available In this paper we examine the impact of channel fading on the bit error rate of a DS-CDMA communication system. The system employs detectors that incorporate neural networks effecting methods of independent component analysis (ICA, subspace estimation of channel noise, and Hopfield type neural networks. The Rayleigh fading channel model is used. When employed in a Rayleigh fading environment, the ICA neural network detectors that give superior performance in a flat fading channel did not retain this superior performance. We then present a new method of compensating for channel fading based on the incorporation of priors in the ICA neural network learning algorithms. When the ICA neural network detectors were compensated using the incorporation of priors, they give significantly better performance than the traditional detectors and the uncompensated ICA detectors. Keywords: CDMA, Multi-user Detection, Rayleigh Fading, Multipath Detection, Independent Component Analysis, Prior Probability Hebbian Learning, Natural Gradient

Blind Multiuser Detection by Kurtosis Maximization for Asynchronous Multirate DS/CDMA Systems

Directory of Open Access Journals (Sweden)

Peng Chun-Hsien

2006-01-01

Full Text Available Chi et al. proposed a fast kurtosis maximization algorithm (FKMA for blind equalization/deconvolution of multiple-input multiple-output (MIMO linear time-invariant systems. This algorithm has been applied to blind multiuser detection of single-rate direct-sequence/code-division multiple-access (DS/CDMA systems and blind source separation (or independent component analysis. In this paper, the FKMA is further applied to blind multiuser detection for multirate DS/CDMA systems. The ideas are to properly formulate discrete-time MIMO signal models by converting real multirate users into single-rate virtual users, followed by the use of FKMA for extraction of virtual users' data sequences associated with the desired user, and recovery of the data sequence of the desired user from estimated virtual users' data sequences. Assuming that all the users' spreading sequences are given a priori, two multirate blind multiuser detection algorithms (with either a single receive antenna or multiple antennas, which also enjoy the merits of superexponential convergence rate and guaranteed convergence of the FKMA, are proposed in the paper, one based on a convolutional MIMO signal model and the other based on an instantaneous MIMO signal model. Some simulation results are then presented to demonstrate their effectiveness and to provide a performance comparison with some existing algorithms.

Orthogonal Multi-Carrier DS-CDMA with Frequency-Domain Equalization

Science.gov (United States)

Tanaka, Ken; Tomeba, Hiromichi; Adachi, Fumiyuki

Orthogonal multi-carrier direct sequence code division multiple access (orthogonal MC DS-CDMA) is a combination of orthogonal frequency division multiplexing (OFDM) and time-domain spreading, while multi-carrier code division multiple access (MC-CDMA) is a combination of OFDM and frequency-domain spreading. In MC-CDMA, a good bit error rate (BER) performance can be achieved by using frequency-domain equalization (FDE), since the frequency diversity gain is obtained. On the other hand, the conventional orthogonal MC DS-CDMA fails to achieve any frequency diversity gain. In this paper, we propose a new orthogonal MC DS-CDMA that can obtain the frequency diversity gain by applying FDE. The conditional BER analysis is presented. The theoretical average BER performance in a frequency-selective Rayleigh fading channel is evaluated by the Monte-Carlo numerical computation method using the derived conditional BER and is confirmed by computer simulation of the orthogonal MC DS-CDMA signal transmission.

DPLL implementation in carrier acquisition and tracking for burst DS-CDMA receivers.

Science.gov (United States)

Guan, Yun-feng; Zhang, Zhao-yang; Lai, Li-feng

2003-01-01

This paper presents the architectures, algorithms, and implementation considerations of the digital phase locked loop (DPLL) used for burst-mode packet DS-CDMA receivers. As we know, carrier offset is a rather challenging problem in CDMA system. According to different applications, different DPLL forms should be adopted to correct different maximum carrier offset in CDMA systems. One classical DPLL and two novel DPLL forms are discussed in the paper. The acquisition range of carrier offset can be widened by using the two novel DPLL forms without any performance degradation such as longer acquisition time or larger variance of the phase error. The maximum acquisition range is 1/(4T), where T is the symbol period. The design can be implemented by FPGA directly.

Performance comparison between S-ALOHA and R3T protocols for multirate OFFH-CDMA systems in optical packet networks

Science.gov (United States)

Inaty, Elie; Raad, Robert; Fortier, Paul; Shalaby, Hossam M.

2006-12-01

We discuss two newly proposed multiple-access control (MAC) protocols for multirate optical code-division multiple access (OCDMA) networks. The first protocol is slotted ALOHA/optical fast-frequency-hopping code-division multiple access (S-ALOHA/OFFH-CDMA), and the second is round-robin receiver-transmitter/optical fast-frequency-hopping code-division multiple access (R3/OFFH-CDMA). Our main subject is to exploit the potential of the optical fast-frequency-hopping CDMA using a fiber Bragg grating when jointly used with two different MAC protocols in a link layer as an effective way of integrating multirate traffic. The system throughput and the average packet delay are compared for both systems. It is shown that S-ALOHA is better than R3T when the user's activity and the offered load are high, whereas R3T is better for smaller values. Both protocols can be competitive in terms of the system throughput, with the advantage going to the R3T protocol at a moderate offered load. However, the R3T protocol suffers a higher delay mainly because of the presence of additional modes. Finally, the overlapped OCDMA system always outperforms the variable processing gain (VPG) OCDMA system regardless of the protocol used.

Nonlinearity effect of electro-optical modulator response in double spread CDMA radio-over-fiber transmissions

Science.gov (United States)

Huang, Jen-Fa; Yen, Chih-Ta; Li, Tzung-Yen

2008-07-01

This study presents a double-spread code-division multiple-access (CDMA) scheme for radio-over-fiber (RoF) transmissions. The network coder/decoders (codecs) are implemented using arrayed-waveguide grating (AWG) routers coded with maximal-length sequence ( M-sequence) codes. The effects of phase-induced intensity noise (PIIN) and multiple-access interference (MAI) on the system performance are evaluated numerically for different values of the optical modulation index (OMI) during the nonlinear electro-optical modulator (EOM) response. At low OMI optical device noise is dominant, but at high OMI nonlinear effect becomes significant. Numerical result shows that the system performance is highly sensitive to the OMI. Therefore, specifying an appropriate value of the OMI is essential in optimizing the system performance. The influence of the degree of polarization (DOP) in the system is also discussed. By employing the scrambler in front of the balanced photo-detector, the system performance can be enhanced. The high-performance, low-cost characteristics of the double-spread CDMA render the scheme an ideal solution for radio-CDMA wireless system cascaded with optical CDMA network.

A performance analysis of DS-CDMA and SCPC VSAT networks

Science.gov (United States)

Hayes, David P.; Ha, Tri T.

1990-01-01

Spread-spectrum and single-channel-per-carrier (SCPC) transmission techniques work well in very small aperture terminal (VSAT) networks for multiple-access purposes while allowing the earth station antennas to remain small. Direct-sequence code-division multiple-access (DS-CDMA) is the simplest spread-spectrum technique to use in a VSAT network since a frequency synthesizer is not required for each terminal. An examination is made of the DS-CDMA and SCPC Ku-band VSAT satellite systems for low-density (64-kb/s or less) communications. A method for improving the standardf link analysis of DS-CDMA satellite-switched networks by including certain losses is developed. The performance of 50-channel full mesh and star network architectures is analyzed. The selection of operating conditions producing optimum performance is demonstrated.

Fast frequency hopping codes applied to SAC optical CDMA network

Science.gov (United States)

Tseng, Shin-Pin

2015-06-01

This study designed a fast frequency hopping (FFH) code family suitable for application in spectral-amplitude-coding (SAC) optical code-division multiple-access (CDMA) networks. The FFH code family can effectively suppress the effects of multiuser interference and had its origin in the frequency hopping code family. Additional codes were developed as secure codewords for enhancing the security of the network. In considering the system cost and flexibility, simple optical encoders/decoders using fiber Bragg gratings (FBGs) and a set of optical securers using two arrayed-waveguide grating (AWG) demultiplexers (DeMUXs) were also constructed. Based on a Gaussian approximation, expressions for evaluating the bit error rate (BER) and spectral efficiency (SE) of SAC optical CDMA networks are presented. The results indicated that the proposed SAC optical CDMA network exhibited favorable performance.

Improving performance of DS-CDMA systems using chaotic complex Bernoulli spreading codes

Science.gov (United States)

Farzan Sabahi, Mohammad; Dehghanfard, Ali

2014-12-01

The most important goal of spreading spectrum communication system is to protect communication signals against interference and exploitation of information by unintended listeners. In fact, low probability of detection and low probability of intercept are two important parameters to increase the performance of the system. In Direct Sequence Code Division Multiple Access (DS-CDMA) systems, these properties are achieved by multiplying the data information in spreading sequences. Chaotic sequences, with their particular properties, have numerous applications in constructing spreading codes. Using one-dimensional Bernoulli chaotic sequence as spreading code is proposed in literature previously. The main feature of this sequence is its negative auto-correlation at lag of 1, which with proper design, leads to increase in efficiency of the communication system based on these codes. On the other hand, employing the complex chaotic sequences as spreading sequence also has been discussed in several papers. In this paper, use of two-dimensional Bernoulli chaotic sequences is proposed as spreading codes. The performance of a multi-user synchronous and asynchronous DS-CDMA system will be evaluated by applying these sequences under Additive White Gaussian Noise (AWGN) and fading channel. Simulation results indicate improvement of the performance in comparison with conventional spreading codes like Gold codes as well as similar complex chaotic spreading sequences. Similar to one-dimensional Bernoulli chaotic sequences, the proposed sequences also have negative auto-correlation. Besides, construction of complex sequences with lower average cross-correlation is possible with the proposed method.

Joint Impact of Frequency Synchronization Errors and Intermodulation Distortion on the Performance of Multicarrier DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Rugini Luca

2005-01-01

Full Text Available The performance of multicarrier systems is highly impaired by intercarrier interference (ICI due to frequency synchronization errors at the receiver and by intermodulation distortion (IMD introduced by a nonlinear amplifier (NLA at the transmitter. In this paper, we evaluate the bit-error rate (BER of multicarrier direct-sequence code-division multiple-access (MC-DS-CDMA downlink systems subject to these impairments in frequency-selective Rayleigh fading channels, assuming quadrature amplitude modulation (QAM. The analytical findings allow to establish the sensitivity of MC-DS-CDMA systems to carrier frequency offset (CFO and NLA distortions, to identify the maximum CFO that is tolerable at the receiver side in different scenarios, and to find out the optimum value of the NLA output power backoff for a given CFO. Simulation results show that the approximated analysis is quite accurate in several conditions.

Modeling and Analysis of Cellular CDMA Forward Channel

National Research Council Canada - National Science Library

Tighe, Jan

2001-01-01

In this thesis, we develop the forward channel model for a DS-CDMA cellular system operating in a slow-flat Rayleigh fading and log normal shadowing environment, which incorporates the extended Hata...

Development of a mobile emergency patient information and imaging communication system based on CDMA-1X EVDO

Science.gov (United States)

Yang, Keon Ho; Jung, Haijo; Kang, Won-Suk; Jang, Bong Mun; Kim, Joong Il; Han, Dong Hoon; Yoo, Sun-Kook; Yoo, Hyung-Sik; Kim, Hee-Joung

2006-03-01

The wireless mobile service with a high bit rate using CDMA-1X EVDO is now widely used in Korea. Mobile devices are also increasingly being used as the conventional communication mechanism. We have developed a web-based mobile system that communicates patient information and images, using CDMA-1X EVDO for emergency diagnosis. It is composed of a Mobile web application system using the Microsoft Windows 2003 server and an internet information service. Also, a mobile web PACS used for a database managing patient information and images was developed by using Microsoft access 2003. A wireless mobile emergency patient information and imaging communication system is developed by using Microsoft Visual Studio.NET, and JPEG 2000 ActiveX control for PDA phone was developed by using the Microsoft Embedded Visual C++. Also, the CDMA-1X EVDO is used for connections between mobile web servers and the PDA phone. This system allows fast access to the patient information database, storing both medical images and patient information anytime and anywhere. Especially, images were compressed into a JPEG2000 format and transmitted from a mobile web PACS inside the hospital to the radiologist using a PDA phone located outside the hospital. Also, this system shows radiological images as well as physiological signal data, including blood pressure, vital signs and so on, in the web browser of the PDA phone so radiologists can diagnose more effectively. Also, we acquired good results using an RW-6100 PDA phone used in the university hospital system of the Sinchon Severance Hospital in Korea.

Methodology and Implementation on DSP of Heuristic Multiuser DS/CDMA Detectors

Directory of Open Access Journals (Sweden)

Alex Miyamoto Mussi

2010-12-01

Full Text Available The growing number of users of mobile communications networks and the scarcity of the electromagnetic spectrum make the use of diversity techniques and detection/decoding efficient, such as the use of multiple antennas at the transmitter and/or receiver, multiuser detection (MuD – Multiuser Detection, among others, have an increasingly prominent role in the telecommunications landscape. This paper presents a design methodology based on digital signal processors (DSP – Digital Signal Processor with a view to the implementation of multiuser heuristics detectors in systems DS/CDMA (Direct Sequence Code Division Multiple Access. Heuristics detection techniques result in near-optimal performance in order to approach the performance of maximum-likelihood (ML. In this work, was employed the DSP development platform called the C6713 DSK, which is based in Texas TMS320C6713 processor. The heuristics techniques proposed are based on well established algorithms in the literature. The efficiency of the algorithms implemented in DSP has been evaluated numerically by computing the measure of bit error rate (BER. Finally, the feasibility of implementation in DSP could then be verified by comparing results from multiple Monte-Carlo simulation in Matlab, with those obtained from implementation on DSP. It also demonstrates the effective increase in performance and system capacity of DS/CDMA with the use of heuristic multiuser detection techniques, implemented directly in the DSP.

Impact of Different Spreading Codes Using FEC on DWT Based MC-CDMA System

OpenAIRE

Masum, Saleh; Kabir, M. Hasnat; Islam, Md. Matiqul; Shams, Rifat Ara; Ullah, Shaikh Enayet

2012-01-01

The effect of different spreading codes in DWT based MC-CDMA wireless communication system is investigated. In this paper, we present the Bit Error Rate (BER) performance of different spreading codes (Walsh-Hadamard code, Orthogonal gold code and Golay complementary sequences) using Forward Error Correction (FEC) of the proposed system. The data is analyzed and is compared among different spreading codes in both coded and uncoded cases. It is found via computer simulation that the performance...

Forward Link Power Control Strategy and its Optimum Issue in CDMA Cellular Networks

Institute of Scientific and Technical Information of China (English)

无

2000-01-01

In this paper, we propose a theoretical method in order to estimate the forward link outage probability and user capacity of a cellular system which are based on IS-95 CDMA standard, especialy impact of power control strategy and voice activity monitoring in the system under long-term fading effects, in which the light and heavy fadings are considered. According to the numerical results obtained in this paper, the power control strategy leads to approximately the threefold user capacity in contrast to the situation without power control strategy. The reults are compared with Interference-to-Signal Ratio (ISR) driven power control scheme[6][9] which can be used only for simulation of the system. The power control strategy not only improves the desired signal to the interference ratio in the reference user's receiver, but also offers uniform service to the user wherever it is located in the cell.

Characterizing CDMA downlink feasibility via effective interference

NARCIS (Netherlands)

Endrayanto, A.I.; van den Berg, Hans Leo; Boucherie, Richardus J.

2003-01-01

This paper models and analyses downlink power assignment feasibility in Code Division Multiple Access (CDMA) mobile networks. By discretizing the area into small segments, the power requirements are characterized via a matrix representation that separates user and system characteristics. We obtain a

Asynchronous, Decentralized DS-CDMA Using Feedback-Controlled Spreading Sequences for Time-Dispersive Channels

Science.gov (United States)

Miyatake, Teruhiko; Chiba, Kazuki; Hamamura, Masanori; Tachikawa, Shin'ichi

We propose a novel asynchronous direct-sequence codedivision multiple access (DS-CDMA) using feedback-controlled spreading sequences (FCSSs) (FCSS/DS-CDMA). At the receiver of FCSS/DS-CDMA, the code-orthogonalizing filter (COF) produces a spreading sequence, and the receiver returns the spreading sequence to the transmitter. Then the transmitter uses the spreading sequence as its updated version. The performance of FCSS/DS-CDMA is evaluated over time-dispersive channels. The results indicate that FCSS/DS-CDMA greatly suppresses both the intersymbol interference (ISI) and multiple access interference (MAI) over time-invariant channels. FCSS/DS-CDMA is applicable to the decentralized multiple access.

SOFT AND SOFTER HANDOVER PERFORMANCE OF CDMA

Directory of Open Access Journals (Sweden)

Lina wati

2010-12-01

Full Text Available One of telecommunication providers in Indonesia applies CDMA2000 1x technology. The technology hasmany advantages such as larger channel capacity of BTS (Base Transceiver Station. On the other hand, thecapacity depends on user’s density. Therefore to guarantee voice connection when user or mobile station (MS isalways moving from one cell to others, handover technique is needed. However the technique can be failed for manyreasons. Therefore impact of call attempt on softer and soft handover performance is investigated. Hence the paperexamined soft – softer handover performance of CDMA in BTS (Base Transceiver Station, BSC, and Sectors inboth sub-urban and rural areas in Denpasar, Bali with area code of 0361.The research has been done in rural and suburban area with call area code ‘0361’. The analyses includedregression and simple linear correlation applications. The results showed that number of call attempts affected thefailure of soft and softer handover technique dominantly. Generally, average level of success both handover in bothrural and suburban area were about 99% which are above KPI (Key Performance Indicator reference at 98.50%.However in rural area, other factors such as blocking called attempt and error called number have caused the softerhandover failure.

Design of power controller in CDMA system with power and SIR error minimization

Institute of Scientific and Technical Information of China (English)

Shulan KONG; Huanshui ZHANG; Zhaosheng ZHANG; Hongxia WANG

2007-01-01

In this paper, an uplink power control problem is considered for code division multiple access (CDMA) systems. A distributed algorithm is proposed based on linear quadratic optimal control theory. The proposed scheme minimizes the sum of the power and the error of signal-to-interference ratio (SIR). A power controller is designed by constructing an optimization problem of a stochastic linear quadratic type in Krein space and solving a Kalman filter problem.

Cross-Layer Admission Control Policy for CDMA Beamforming Systems

Directory of Open Access Journals (Sweden)

Sheng Wei

2007-01-01

Full Text Available A novel admission control (AC policy is proposed for the uplink of a cellular CDMA beamforming system. An approximated power control feasibility condition (PCFC, required by a cross-layer AC policy, is derived. This approximation, however, increases outage probability in the physical layer. A truncated automatic retransmission request (ARQ scheme is then employed to mitigate the outage problem. In this paper, we investigate the joint design of an AC policy and an ARQ-based outage mitigation algorithm in a cross-layer context. This paper provides a framework for joint AC design among physical, data-link, and network layers. This enables multiple quality-of-service (QoS requirements to be more flexibly used to optimize system performance. Numerical examples show that by appropriately choosing ARQ parameters, the proposed AC policy can achieve a significant performance gain in terms of reduced outage probability and increased system throughput, while simultaneously guaranteeing all the QoS requirements.

Subcarrier Group Assignment for MC-CDMA Wireless Networks

Directory of Open Access Journals (Sweden)

Le-Ngoc Tho

2007-01-01

Full Text Available Two interference-based subcarrier group assignment strategies in dynamic resource allocation are proposed for MC-CDMA wireless systems to achieve high throughput in a multicell environment. Least interfered group assignment (LIGA selects for each session the subcarrier group on which the user receives the minimum interference, while best channel ratio group assignment (BCRGA chooses the subcarrier group with the largest channel response-to-interference ratio. Both analytical framework and simulation model are developed for evaluation of throughput distribution of the proposed schemes. An iterative approach is devised to handle the complex interdependency between multicell interference profiles in the throughput analysis. Illustrative results show significant throughput improvement offered by the interference-based assignment schemes for MC-CDMA multicell wireless systems. In particular, under low loading conditions, LIGA renders the best performance. However, as the load increases BCRGA tends to offer superior performance.

Subcarrier Group Assignment for MC-CDMA Wireless Networks

Directory of Open Access Journals (Sweden)

Tho Le-Ngoc

2007-12-01

Full Text Available Two interference-based subcarrier group assignment strategies in dynamic resource allocation are proposed for MC-CDMA wireless systems to achieve high throughput in a multicell environment. Least interfered group assignment (LIGA selects for each session the subcarrier group on which the user receives the minimum interference, while best channel ratio group assignment (BCRGA chooses the subcarrier group with the largest channel response-to-interference ratio. Both analytical framework and simulation model are developed for evaluation of throughput distribution of the proposed schemes. An iterative approach is devised to handle the complex interdependency between multicell interference profiles in the throughput analysis. Illustrative results show significant throughput improvement offered by the interference-based assignment schemes for MC-CDMA multicell wireless systems. In particular, under low loading conditions, LIGA renders the best performance. However, as the load increases BCRGA tends to offer superior performance.

Performance Analysis of Wavelet Based MC-CDMA System with Implementation of Various Antenna Diversity Schemes

OpenAIRE

Islam, Md. Matiqul; Kabir, M. Hasnat; Ullah, Sk. Enayet

2012-01-01

The impact of using wavelet based technique on the performance of a MC-CDMA wireless communication system has been investigated. The system under proposed study incorporates Walsh Hadamard codes to discriminate the message signal for individual user. A computer program written in Mathlab source code is developed and this simulation study is made with implementation of various antenna diversity schemes and fading (Rayleigh and Rician) channel. Computer simulation results demonstrate that the p...

Uniform Circular Antenna Array Applications in Coded DS-CDMA Mobile Communication Systems

National Research Council Canada - National Science Library

Seow, Tian

2003-01-01

...) has greatly increased. This thesis examines the use of an equally spaced circular adaptive antenna array at the mobile station for a typical coded direct sequence code division multiple access (DS-CDMA...

Coherent Code Tracking for Spatial Transmit Diversity DS-CDMA Systems

Directory of Open Access Journals (Sweden)

R. W. Stewart

2005-09-01

Full Text Available Spatial transmit diversity schemes are now well integrated into third-generation cellular mobile communication system specifications. When DS-CDMA-based technology is deployed in typical macro- and microcell environments, multipath diversity and spatial diversity may be exploited simultaneously by a 2D RAKE receiver. The work presented in this paper focuses on taking advantage of spatial transmit diversity in synchronising the 2D RAKE structure. We investigate the use of coherent and noncoherent techniques for tracking the timing parameters of each multipath component. It is shown that both noncoherent and coherent techniques benefit from transmit diversity. Additionally the performance gap between these two techniques increases with the number of antennas.

Demonstration of the CDMA-mode CAOS smart camera.

Science.gov (United States)

Riza, Nabeel A; Mazhar, Mohsin A

2017-12-11

Demonstrated is the code division multiple access (CDMA)-mode coded access optical sensor (CAOS) smart camera suited for bright target scenarios. Deploying a silicon CMOS sensor and a silicon point detector within a digital micro-mirror device (DMD)-based spatially isolating hybrid camera design, this smart imager first engages the DMD starring mode with a controlled factor of 200 high optical attenuation of the scene irradiance to provide a classic unsaturated CMOS sensor-based image for target intelligence gathering. Next, this CMOS sensor provided image data is used to acquire a focused zone more robust un-attenuated true target image using the time-modulated CDMA-mode of the CAOS camera. Using four different bright light test target scenes, successfully demonstrated is a proof-of-concept visible band CAOS smart camera operating in the CDMA-mode using up-to 4096 bits length Walsh design CAOS pixel codes with a maximum 10 KHz code bit rate giving a 0.4096 seconds CAOS frame acquisition time. A 16-bit analog-to-digital converter (ADC) with time domain correlation digital signal processing (DSP) generates the CDMA-mode images with a 3600 CAOS pixel count and a best spatial resolution of one micro-mirror square pixel size of 13.68 μm side. The CDMA-mode of the CAOS smart camera is suited for applications where robust high dynamic range (DR) imaging is needed for un-attenuated un-spoiled bright light spectrally diverse targets.

Zero-Forcing and Minimum Mean-Square Error Multiuser Detection in Generalized Multicarrier DS-CDMA Systems for Cognitive Radio

Directory of Open Access Journals (Sweden)

Lie-Liang Yang

2008-01-01

Full Text Available In wireless communications, multicarrier direct-sequence code-division multiple access (MC DS-CDMA constitutes one of the highly flexible multiple access schemes. MC DS-CDMA employs a high number of degrees-of-freedom, which are beneficial to design and reconfiguration for communications in dynamic communications environments, such as in the cognitive radios. In this contribution, we consider the multiuser detection (MUD in MC DS-CDMA, which motivates lowcomplexity, high flexibility, and robustness so that the MUD schemes are suitable for deployment in dynamic communications environments. Specifically, a range of low-complexity MUDs are derived based on the zero-forcing (ZF, minimum mean-square error (MMSE, and interference cancellation (IC principles. The bit-error rate (BER performance of the MC DS-CDMA aided by the proposed MUDs is investigated by simulation approaches. Our study shows that, in addition to the advantages provided by a general ZF, MMSE, or IC-assisted MUD, the proposed MUD schemes can be implemented using modular structures, where most modules are independent of each other. Due to the independent modular structure, in the proposed MUDs one module may be reconfigured without yielding impact on the others. Therefore, the MC DS-CDMA, in conjunction with the proposed MUDs, constitutes one of the promising multiple access schemes for communications in the dynamic communications environments such as in the cognitive radios.

Zero-Forcing and Minimum Mean-Square Error Multiuser Detection in Generalized Multicarrier DS-CDMA Systems for Cognitive Radio

Directory of Open Access Journals (Sweden)

Wang Li-Chun

2008-01-01

Full Text Available Abstract In wireless communications, multicarrier direct-sequence code-division multiple access (MC DS-CDMA constitutes one of the highly flexible multiple access schemes. MC DS-CDMA employs a high number of degrees-of-freedom, which are beneficial to design and reconfiguration for communications in dynamic communications environments, such as in the cognitive radios. In this contribution, we consider the multiuser detection (MUD in MC DS-CDMA, which motivates lowcomplexity, high flexibility, and robustness so that the MUD schemes are suitable for deployment in dynamic communications environments. Specifically, a range of low-complexity MUDs are derived based on the zero-forcing (ZF, minimum mean-square error (MMSE, and interference cancellation (IC principles. The bit-error rate (BER performance of the MC DS-CDMA aided by the proposed MUDs is investigated by simulation approaches. Our study shows that, in addition to the advantages provided by a general ZF, MMSE, or IC-assisted MUD, the proposed MUD schemes can be implemented using modular structures, where most modules are independent of each other. Due to the independent modular structure, in the proposed MUDs one module may be reconfigured without yielding impact on the others. Therefore, the MC DS-CDMA, in conjunction with the proposed MUDs, constitutes one of the promising multiple access schemes for communications in the dynamic communications environments such as in the cognitive radios.

A combinatorial approximation algorithm for CDMA downlink rate allocation

NARCIS (Netherlands)

Boucherie, Richardus J.; Bumb, A.F.; Endrayanto, A.I.; Woeginger, Gerhard; Raghavan, S.; Anandalingam, G.

2006-01-01

This paper presents a combinatorial algorithm for downlink rate allocation in Code Division Multiple Access (CDMA) mobile networks. By discretizing the coverage area into small segments, the transmit power requirements are characterized via a matrix representation that separates user and system

A combinatorial approximation algorithm for CDMA downlink rate allocation

NARCIS (Netherlands)

Boucherie, Richardus J.; Bumb, A.F.; Endrayanto, A.I.; Woeginger, Gerhard

2004-01-01

This paper presents a combinatorial algorithm for downlink rate allocation in Code Division Multiple Access (CDMA) mobile networks. By discretizing the coverage area into small segments, the transmit power requirements are characterized via a matrix representation that separates user and system

Statistical Analysis of Coherent Ultrashort Light Pulse CDMA With Multiple Optical Amplifiers Using Additive Noise Model

Science.gov (United States)

Jamshidi, Kambiz; Salehi, Jawad A.

2005-05-01

This paper describes a study of the performance of various configurations for placing multiple optical amplifiers in a typical coherent ultrashort light pulse code-division multiple access (CULP-CDMA) communication system using the additive noise model. For this study, a comprehensive performance analysis was developed that takes into account multiple-access noise, noise due to optical amplifiers, and thermal noise using the saddle-point approximation technique. Prior to obtaining the overall system performance, the input/output statistical models for different elements of the system such as encoders/decoders,star coupler, and optical amplifiers were obtained. Performance comparisons between an ideal and lossless quantum-limited case and a typical CULP-CDMA with various losses exhibit more than 30 dB more power requirement to obtain the same bit-error rate (BER). Considering the saturation effect of optical amplifiers, this paper discusses an algorithm for amplifiers' gain setting in various stages of the network in order to overcome the nonlinear effects on signal modulation in optical amplifiers. Finally, using this algorithm,various configurations of multiple optical amplifiers in CULP-CDMA are discussed and the rules for the required optimum number of amplifiers are shown with their corresponding optimum locations to be implemented along the CULP-CDMA system.

The analysis of MAI in large scale MIMO-CDMA system

Science.gov (United States)

Berceanu, Madalina-Georgiana; Voicu, Carmen; Halunga, Simona

2016-12-01

Recently, technological development imposed a rapid growth in the use of data carried by cellular services, which also implies the necessity of higher data rates and lower latency. To meet the users' demands, it was brought into discussion a series of new data processing techniques. In this paper, we approached the MIMO technology that uses multiple antennas at the receiver and transmitter ends. To study the performances obtained by this technology, we proposed a MIMO-CDMA system, where image transmission has been used instead of random data transmission to take benefit of a larger range of quality indicators. In the simulations we increased the number of antennas, we observed how the performances of the system are modified and, based on that, we were able to make a comparison between a conventional MIMO and a Large Scale MIMO system, in terms of BER and MSSIM index, which is a metric that compares the quality of the image before transmission with the received one.

A Review on Successive Interference Cancellation Scheme Based on Optical CDMA Network

Science.gov (United States)

Alsowaidi, N.; Eltaif, T.; Mokhtar, M. R.

2014-12-01

Due to various desirable features of optical code division multiple access (OCDMA), it is believed this technique once developed and commercially available will be an integral part of optical access networks. Optical CDMA system suffers from a problem called multiple access interference (MAI) which limits the number of active users, it occurs when number of active users share the same carriers. The aim of this paper is to review successive interference cancellation (SIC) scheme based on optical CDMA system. The paper also reviews the system performance in presence of shot noise, thermal noise, and phase-induced intensity noise (PIIN). A comprehensive review on the mathematical model of SIC scheme using direct detection (DS) and spectral amplitude coding (SAC) were presented in this article.

Multipass Channel Estimation and Joint Multiuser Detection and Equalization for MIMO Long-Code DS/CDMA Systems

Directory of Open Access Journals (Sweden)

Buzzi Stefano

2006-01-01

Full Text Available The problem of joint channel estimation, equalization, and multiuser detection for a multiantenna DS/CDMA system operating over a frequency-selective fading channel and adopting long aperiodic spreading codes is considered in this paper. First of all, we present several channel estimation and multiuser data detection schemes suited for multiantenna long-code DS/CDMA systems. Then, a multipass strategy, wherein the data detection and the channel estimation procedures exchange information in a recursive fashion, is introduced and analyzed for the proposed scenario. Remarkably, this strategy provides, at the price of some attendant computational complexity increase, excellent performance even when very short training sequences are transmitted, and thus couples together the conflicting advantages of both trained and blind systems, that is, good performance and no wasted bandwidth, respectively. Space-time coded systems are also considered, and it is shown that the multipass strategy provides excellent results for such systems also. Likewise, it is also shown that excellent performance is achieved also when each user adopts the same spreading code for all of its transmit antennas. The validity of the proposed procedure is corroborated by both simulation results and analytical findings. In particular, it is shown that adopting the multipass strategy results in a remarkable reduction of the channel estimation mean-square error and of the optimal length of the training sequence.

Effects of optical layer impairments on 2.5 Gb/s optical CDMA transmission.

Science.gov (United States)

Feng, H; Mendez, A; Heritage, J; Lennon, W

2000-07-03

We conducted a computer simulation study to assess the effects of optical layer impairments on optical CDMA (O-CDMA) transmission of 8 asynchronous users at 2.5 Gb/s each user over a 214-km link. It was found that with group velocity dispersion compensation, two other residual effects, namely, the nonzero chromatic dispersion slope of the single mode fiber (which causes skew) and the non-uniform EDFA gain (which causes interference power level to exceed signal power level of some codes) degrade the signal to multi-access interference (MAI) ratio. In contrast, four wave mixing and modulation due to the Kerr and Raman contributions to the fiber nonlinear refractive index are less important. Current wavelength-division multiplexing (WDM) technologies, including dispersion management, EDFA gain flattening, and 3 rd order dispersion compensation, are sufficient to overcome the impairments to the O-CDMA transmission system that we considered.

Genetic Local Search for Optimum Multiuser Detection Problem in DS-CDMA Systems

Science.gov (United States)

Wang, Shaowei; Ji, Xiaoyong

Optimum multiuser detection (OMD) in direct-sequence code-division multiple access (DS-CDMA) systems is an NP-complete problem. In this paper, we present a genetic local search algorithm, which consists of an evolution strategy framework and a local improvement procedure. The evolution strategy searches the space of feasible, locally optimal solutions only. A fast iterated local search algorithm, which employs the proprietary characteristics of the OMD problem, produces local optima with great efficiency. Computer simulations show the bit error rate (BER) performance of the GLS outperforms other multiuser detectors in all cases discussed. The computation time is polynomial complexity in the number of users.

OFDM and MC-CDMA for broadband multi-user communications WLANs and broadcasting

CERN Document Server

2003-01-01

"OFDM systems have experienced increased attention in recent years and have found applications in a number of diverse areas including telephone-line based ADSL links, digital audio and video broadcasting systems, and wireless local area networks. OFDM is being considered for the next-generation of wireless systems both with and without direct sequence spreading and the resultant spreading-based multi-carrier CDMA systems have numerous attractive properties. This volume provides the reader with a broad overview of the research on OFDM systems during their 40-year history. Part I commences with an easy to read conceptual, rather than mathematical, treatment of the basic design issues of OFDM systems. The discussions gradually deepen to include adaptive single and multi-user OFDM systems invoking adaptive turbo coding. Part II introduces the taxonomy of multi-carrier CDMA systems and deals with the design of their spreading codes and the objective of minimising their crest factors. This part also compares the be...

Multi-Hop Link Capacity of Multi-Route Multi-Hop MRC Diversity for a Virtual Cellular Network

Science.gov (United States)

Daou, Imane; Kudoh, Eisuke; Adachi, Fumiyuki

In virtual cellular network (VCN), proposed for high-speed mobile communications, the signal transmitted from a mobile terminal is received by some wireless ports distributed in each virtual cell and relayed to the central port that acts as a gateway to the core network. In this paper, we apply the multi-route MHMRC diversity in order to decrease the transmit power and increase the multi-hop link capacity. The transmit power, the interference power and the link capacity are evaluated for DS-CDMA multi-hop VCN by computer simulation. The multi-route MHMRC diversity can be applied to not only DS-CDMA but also other access schemes (i. e. MC-CDMA, OFDM, etc.).

Performance Evaluation of a Novel CDMA Detection Technique: The Two-State Approach

Directory of Open Access Journals (Sweden)

Luca Simone Ronga

2005-04-01

Full Text Available The use of code division multiple access (CDMA makes third-generation wireless systems interference limited rather than noise limited. The research for new methods to reduce interference and increase efficiency lead us to formulate a signaling method where fast impulsive silence states are mapped on zero-energy symbols. The theoretical formulation of the optimum receiver is reported and the asymptotic multiuser efficiency (AME as well as an upper bound of the probability of error have been derived and applied to the conventional receiver and the decorrelating detector. Moreover, computer simulations have been performed to show the advantages of the proposed two-state scheme over the traditional single-state receiver in a multiuser CDMA system operating in a multipath fading channel.

A Combined Antenna Arrays and Reverse-Link Synchronous DS-CDMA System over Frequency-Selective Fading Channels with Power Control Error

Directory of Open Access Journals (Sweden)

Yong-Seok Kim

2004-08-01

Full Text Available An improved antenna array (AA has been introduced, in which reverse-link synchronous transmission technique (RLSTT is incorporated to effectively make better an estimation of covariance matrices at a beamformer-RAKE receiver. While RLSTT is effective in the first finger at the RAKE receiver in order to reject multiple-access interference (MAI, the beamformer estimates the desired user's complex weights, enhancing its signal and reducing cochannel interference (CCI from the other directions. In this work, it is attempted to provide a comprehensive analysis of user capacity which reflects several important factors such as the shape of multipath intensity profile (MIP, the number of antennas, and power control error (PCE. Theoretical analysis, confirmed by the simulations, demonstrates that the orthogonality provided by employing RLSTT along with AA may make the DS-CDMA system insensitive to the PCE even with fewer numbers of antennas.

Capacity of multiservice WCDMA networks with variable GoS

NARCIS (Netherlands)

Hegde, N.; Altman, E.

2006-01-01

Traditional definitions of capacity of CDMA networks are either related to the number of calls they can handle (pole capacity) or to the arrival rate that guarantees that the rejection rate (or outage) is below a given fraction (Erlang capacity). We extend the latter definition to other quality of

Performance Comparison of Orthogonal and Quasi-orthogonal Codes in Quasi-Synchronous Cellular CDMA Communication

Science.gov (United States)

Jos, Sujit; Kumar, Preetam; Chakrabarti, Saswat

Orthogonal and quasi-orthogonal codes are integral part of any DS-CDMA based cellular systems. Orthogonal codes are ideal for use in perfectly synchronous scenario like downlink cellular communication. Quasi-orthogonal codes are preferred over orthogonal codes in the uplink communication where perfect synchronization cannot be achieved. In this paper, we attempt to compare orthogonal and quasi-orthogonal codes in presence of timing synchronization error. This will give insight into the synchronization demands in DS-CDMA systems employing the two classes of sequences. The synchronization error considered is smaller than chip duration. Monte-Carlo simulations have been carried out to verify the analytical and numerical results.

Average Likelihood Methods of Classification of Code Division Multiple Access (CDMA)

Science.gov (United States)

2016-05-01

subject to code matrices that follows the structure given by (113). [⃗ yR y⃗I ] = √ Es 2L [ GR1 −GI1 GI2 GR2 ] [ QR −QI QI QR ] [⃗ bR b⃗I ] + [⃗ nR n⃗I... QR ] [⃗ b+ b⃗− ] + [⃗ n+ n⃗− ] (115) The average likelihood for type 4 CDMA (116) is a special case of type 1 CDMA with twice the code length and...AVERAGE LIKELIHOOD METHODS OF CLASSIFICATION OF CODE DIVISION MULTIPLE ACCESS (CDMA) MAY 2016 FINAL TECHNICAL REPORT APPROVED FOR PUBLIC RELEASE

A hybrid path-oriented code assignment CDMA-based MAC protocol for underwater acoustic sensor networks.

Science.gov (United States)

Chen, Huifang; Fan, Guangyu; Xie, Lei; Cui, Jun-Hong

2013-11-04

Due to the characteristics of underwater acoustic channel, media access control (MAC) protocols designed for underwater acoustic sensor networks (UWASNs) are quite different from those for terrestrial wireless sensor networks. Moreover, in a sink-oriented network with event information generation in a sensor field and message forwarding to the sink hop-by-hop, the sensors near the sink have to transmit more packets than those far from the sink, and then a funneling effect occurs, which leads to packet congestion, collisions and losses, especially in UWASNs with long propagation delays. An improved CDMA-based MAC protocol, named path-oriented code assignment (POCA) CDMA MAC (POCA-CDMA-MAC), is proposed for UWASNs in this paper. In the proposed MAC protocol, both the round-robin method and CDMA technology are adopted to make the sink receive packets from multiple paths simultaneously. Since the number of paths for information gathering is much less than that of nodes, the length of the spreading code used in the POCA-CDMA-MAC protocol is shorter greatly than that used in the CDMA-based protocols with transmitter-oriented code assignment (TOCA) or receiver-oriented code assignment (ROCA). Simulation results show that the proposed POCA-CDMA-MAC protocol achieves a higher network throughput and a lower end-to-end delay compared to other CDMA-based MAC protocols.

A Hybrid Path-Oriented Code Assignment CDMA-Based MAC Protocol for Underwater Acoustic Sensor Networks

Directory of Open Access Journals (Sweden)

Huifang Chen

2013-11-01

Full Text Available Due to the characteristics of underwater acoustic channel, media access control (MAC protocols designed for underwater acoustic sensor networks (UWASNs are quite different from those for terrestrial wireless sensor networks. Moreover, in a sink-oriented network with event information generation in a sensor field and message forwarding to the sink hop-by-hop, the sensors near the sink have to transmit more packets than those far from the sink, and then a funneling effect occurs, which leads to packet congestion, collisions and losses, especially in UWASNs with long propagation delays. An improved CDMA-based MAC protocol, named path-oriented code assignment (POCA CDMA MAC (POCA-CDMA-MAC, is proposed for UWASNs in this paper. In the proposed MAC protocol, both the round-robin method and CDMA technology are adopted to make the sink receive packets from multiple paths simultaneously. Since the number of paths for information gathering is much less than that of nodes, the length of the spreading code used in the POCA-CDMA-MAC protocol is shorter greatly than that used in the CDMA-based protocols with transmitter-oriented code assignment (TOCA or receiver-oriented code assignment (ROCA. Simulation results show that the proposed POCA-CDMA-MAC protocol achieves a higher network throughput and a lower end-to-end delay compared to other CDMA-based MAC protocols.

CDMA2000 Y WCDMA

Directory of Open Access Journals (Sweden)

Jaime Sánchez García

2005-01-01

Full Text Available Este artículo ofrece un panorama general de los sistemas de comunicaciones móviles celulares de tercera generación (3G que han tenido una mayor aceptación (CDMA2000 y WCDMA en el mercado, y una comparación basada en los puntos principales donde los sistemas difieren que indica las ventajas y desventajas de cada uno. Los sistemas de comunicaciones móviles celulares 3G ofrecen mayores capacidades de transmisión a los de segunda generación (2G, y permiten brindar, además de los tradicionales servicios de telefonía celular, servicios de comunicación de datos a velocidades más altas que los de 2G. Las redes CDMA2000 y WCDMA forman parte del estándar IMT-2000 definido por la Unión Internacional de Telecomunicaciones (ITU para sistemas de comunicaciones inalámbricas de tercera generación; éstas son redes de banda ancha que ofrecen mayores velocidades de transmisión de datos, servicios de internet y aplicaciones multimedia

An FPGA-based DS-CDMA multiuser demodulator employing adaptive multistage parallel interference cancellation

Science.gov (United States)

Li, Xinhua; Song, Zhenyu; Zhan, Yongjie; Wu, Qiongzhi

2009-12-01

Since the system capacity is severely limited, reducing the multiple access interfere (MAI) is necessary in the multiuser direct-sequence code division multiple access (DS-CDMA) system which is used in the telecommunication terminals data-transferred link system. In this paper, we adopt an adaptive multistage parallel interference cancellation structure in the demodulator based on the least mean square (LMS) algorithm to eliminate the MAI on the basis of overviewing various of multiuser dectection schemes. Neither a training sequence nor a pilot signal is needed in the proposed scheme, and its implementation complexity can be greatly reduced by a LMS approximate algorithm. The algorithm and its FPGA implementation is then derived. Simulation results of the proposed adaptive PIC can outperform some of the existing interference cancellation methods in AWGN channels. The hardware setup of mutiuser demodulator is described, and the experimental results based on it demonstrate that the simulation results shows large performance gains over the conventional single-user demodulator.

Comparison of equalisation strategies for multi-carrier CDMA

OpenAIRE

Cooper, MA; Armour, SMD; Bian, YQ; McGeehan, JP

2003-01-01

This paper focuses on the bit error rate (BER) performance of equalisation strategies for a downlink MC-CDMA based system. Simulation results utilising maximal ratio combining (MRC), orthogonal restoring combining (ORC), equal gain combining (EGC) and minimum mean square error combining (MMSEC) for a multiuser scenario are presented. In addition, we analyse the relative complexities of each scheme and discuss their suitability for implementation in future consumer products

Improved Iterative Parallel Interference Cancellation Receiver for Future Wireless DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Andrea Bernacchioni

2005-04-01

Full Text Available We present a new turbo multiuser detector for turbo-coded direct sequence code division multiple access (DS-CDMA systems. The proposed detector is based on the utilization of a parallel interference cancellation (PIC and a bank of turbo decoders. The PIC is broken up in order to perform interference cancellation after each constituent decoder of the turbo decoding scheme. Moreover, in the paper we propose a new enhanced algorithm that provides a more accurate estimation of the signal-to-noise-plus-interference-ratio used in the tentative decision device and in the MAP decoding algorithm. The performance of the proposed receiver is evaluated by means of computer simulations for medium to very high system loads, in AWGN and multipath fading channel, and compared to recently proposed interference cancellation-based iterative MUD, by taking into account the number of iterations and the complexity involved. We will see that the proposed receiver outperforms the others especially for highly loaded systems.

Spreading Sequence Design for Multiple Cell Synchronous DS-CDMA Systems under Total Weighted Squared Correlation Criterion

Directory of Open Access Journals (Sweden)

Cotae Paul

2004-01-01

Full Text Available An algorithm for designing spreading sequences for an overloaded multicellular synchronous DS-CDMA system on uplink is introduced. The criterion used to measure the optimality of the design is the total weighted square correlation (TWSC assuming the channel state information known perfectly at both transmitter and receiver. By using this algorithm it is possible to obtain orthogonal generalized WBE sequences sets for any processing gain. The bandwidth of initial generalized WBE signals of each cell is preserved in the extended signal space associated to multicellular system. Mathematical formalism is illustrated by selected numerical examples.

Effect of Interleaved FEC Code on Wavelet Based MC-CDMA System with Alamouti STBC in Different Modulation Schemes

OpenAIRE

Shams, Rifat Ara; Kabir, M. Hasnat; Ullah, Sheikh Enayet

2012-01-01

In this paper, the impact of Forward Error Correction (FEC) code namely Trellis code with interleaver on the performance of wavelet based MC-CDMA wireless communication system with the implementation of Alamouti antenna diversity scheme has been investigated in terms of Bit Error Rate (BER) as a function of Signal-to-Noise Ratio (SNR) per bit. Simulation of the system under proposed study has been done in M-ary modulation schemes (MPSK, MQAM and DPSK) over AWGN and Rayleigh fading channel inc...

Secure Communications in High Speed Fiber Optical Networks Using Code Division Multiple Access (CDMA) Transmission

Energy Technology Data Exchange (ETDEWEB)

Han, I; Bond, S; Welty, R; Du, Y; Yoo, S; Reinhardt, C; Behymer, E; Sperry, V; Kobayashi, N

2004-02-12

This project is focused on the development of advanced components and system technologies for secure data transmission on high-speed fiber optic data systems. This work capitalizes on (1) a strong relationship with outstanding faculty at the University of California-Davis who are experts in high speed fiber-optic networks, (2) the realization that code division multiple access (CDMA) is emerging as a bandwidth enhancing technique for fiber optic networks, (3) the realization that CDMA of sufficient complexity forms the basis for almost unbreakable one-time key transmissions, (4) our concepts for superior components for implementing CDMA, (5) our expertise in semiconductor device processing and (6) our Center for Nano and Microtechnology, which is where the majority of the experimental work was done. Here we present a novel device concept, which will push the limits of current technology, and will simultaneously solve system implementation issues by investigating new state-of-the-art fiber technologies. This will enable the development of secure communication systems for the transmission and reception of messages on deployed commercial fiber optic networks, through the CDMA phase encoding of broad bandwidth pulses. CDMA technology has been developed as a multiplexing technology, much like wavelength division multiplexing (WDM) or time division multiplexing (TDM), to increase the potential number of users on a given communication link. A novel application of the techniques created for CDMA is to generate secure communication through physical layer encoding. Physical layer encoding devices are developed which utilize semiconductor waveguides with fast carrier response times to phase encode spectral components of a secure signal. Current commercial technology, most commonly a spatial light modulator, allows phase codes to be changed at rates of only 10's of Hertz ({approx}25ms response). The use of fast (picosecond to nanosecond) carrier dynamics of semiconductors

H∞ Channel Estimation for DS-CDMA Systems: A Partial Difference Equation Approach

Directory of Open Access Journals (Sweden)

Wei Wang

2013-01-01

Full Text Available In the communications literature, a number of different algorithms have been proposed for channel estimation problems with the statistics of the channel noise and observation noise exactly known. In practical systems, however, the channel parameters are often estimated using training sequences which lead to the statistics of the channel noise difficult to obtain. Moreover, the received signals are corrupted not only by the ambient noises but also by multiple-access interferences, so the statistics of observation noises is also difficult to obtain. In this paper, we will investigate the H∞ channel estimation problem for direct-sequence code-division multiple-access (DS-CDMA communication systems with time-varying multipath fading channels. The channel estimator is designed by applying a partial difference equation approach together with the innovation analysis theory. This method can give a sufficient and necessary condition for the existence of an H∞ channel estimator.

Iterative Overlap FDE for Multicode DS-CDMA

Science.gov (United States)

Takeda, Kazuaki; Tomeba, Hiromichi; Adachi, Fumiyuki

Recently, a new frequency-domain equalization (FDE) technique, called overlap FDE, that requires no GI insertion was proposed. However, the residual inter/intra-block interference (IBI) cannot completely be removed. In addition to this, for multicode direct sequence code division multiple access (DS-CDMA), the presence of residual interchip interference (ICI) after FDE distorts orthogonality among the spreading codes. In this paper, we propose an iterative overlap FDE for multicode DS-CDMA to suppress both the residual IBI and the residual ICI. In the iterative overlap FDE, joint minimum mean square error (MMSE)-FDE and ICI cancellation is repeated a sufficient number of times. The bit error rate (BER) performance with the iterative overlap FDE is evaluated by computer simulation.

Effects of simultaneous combined exposure to CDMA and WCDMA electromagnetic fields on serum hormone levels in rats

International Nuclear Information System (INIS)

Jin, Yeung Bae; Choi, Hyung-Do; Kim, Byung Chan; Pack, Jeong-Ki; Kim, Nam; Lee, Yun-Sil

2013-01-01

Despite more than a decade of research on the endocrine system, there have been no published studies about the effects of concurrent exposure of radiofrequency electromagnetic fields (RF-EMF) on this system. The present study investigated the several parameters of the endocrine system including melatonin, thyroid stimulating hormone, stress hormone and sex hormone after code division multiple access (CDMA, 849 MHz) and wideband code division multiple access (WCDMA, 1.95 GHz) signals for simultaneous exposure in rats. Sprague-Dawley rats were exposed to RF-EMF signals for 45 min/day, 5 days/week for up to 8 weeks. The whole-body average specific absorption rate (SAR) of CDMA or WCDMA was 2.0 W/kg (total 4.0 W/kg). At 4 and 8 weeks after the experiment began, each experimental group's 40 rats (male 20, female 20) were autopsied. Exposure for 8 weeks to simultaneous CDMA and WCDMA RF did not affect serum levels in rats of melatonin, thyroid stimulating hormone (TSH), triiodothyronine (T3) and thyroxin (T4), adrenocorticotropic hormone (ACTH) and sex hormones (testosterone and estrogen) as assessed by the ELISA method

Handover aspects for a Low Earth Orbit (LEO) CDMA Land Mobile Satellite (LMS) system

Science.gov (United States)

Carter, P.; Beach, M. A.

1993-01-01

This paper addresses the problem of handoff in a land mobile satellite (LMS) system between adjacent satellites in a low earth orbit (LEO) constellation. In particular, emphasis is placed on the application of soft handoff in a direct sequence code division multiple access (DS-CDMA) LMS system. Soft handoff is explained in terms of terrestrial macroscopic diversity, in which signals transmitted via several independent fading paths are combined to enhance the link quality. This concept is then reconsidered in the context of a LEO LMS system. A two-state Markov channel model is used to simulate the effects of shadowing on the communications path from the mobile to each satellite during handoff. The results of the channel simulation form a platform for discussion regarding soft handoff, highlighting the potential merits of the scheme when applied in a LEO LMS environment.

Iterative MMSE Detection for MIMO/BLAST DS-CDMA Systems in Frequency Selective Fading Channels - Achieving High Performance in Fully Loaded Systems

Science.gov (United States)

Silva, João Carlos; Souto, Nuno; Cercas, Francisco; Dinis, Rui

A MMSE (Minimum Mean Square Error) DS-CDMA (Direct Sequence-Code Division Multiple Access) receiver coupled with a low-complexity iterative interference suppression algorithm was devised for a MIMO/BLAST (Multiple Input, Multiple Output / Bell Laboratories Layered Space Time) system in order to improve system performance, considering frequency selective fading channels. The scheme is compared against the simple MMSE receiver, for both QPSK and 16QAM modulations, under SISO (Single Input, Single Output) and MIMO systems, the latter with 2Tx by 2Rx and 4Tx by 4Rx (MIMO order 2 and 4 respectively) antennas. To assess its performance in an existing system, the uncoded UMTS HSDPA (High Speed Downlink Packet Access) standard was considered.

A Geometrical-Based Model for Cochannel Interference Analysis and Capacity Estimation of CDMA Cellular Systems

Directory of Open Access Journals (Sweden)

Konstantinos B. Baltzis

2008-10-01

Full Text Available A common assumption in cellular communications is the circular-cell approximation. In this paper, an alternative analysis based on the hexagonal shape of the cells is presented. A geometrical-based stochastic model is proposed to describe the angle of arrival of the interfering signals in the reverse link of a cellular system. Explicit closed form expressions are derived, and simulations performed exhibit the characteristics and validate the accuracy of the proposed model. Applications in the capacity estimation of WCDMA cellular networks are presented. Dependence of system capacity of the sectorization of the cells and the base station antenna radiation pattern is explored. Comparisons with data in literature validate the accuracy of the proposed model. The degree of error of the hexagonal and the circular-cell approaches has been investigated indicating the validity of the proposed model. Results have also shown that, in many cases, the two approaches give similar results when the radius of the circle equals to the hexagon inradius. A brief discussion on how the proposed technique may be applied to broadband access networks is finally made.

Experimental Verification and Capacity Prediction of FE-OCDMA Using Superimposed FBG

Science.gov (United States)

Ayotte, Simon; Rochette, Martin; Magné, Julien; Rusch, Leslie A.; Larochelle, Sophie

2005-02-01

This paper presents the experimental demonstration and simulation results of a frequency-encoded optical code-division multiple-access (FE-OCDMA) system using broad-band incoherent source, superimposed fiber Bragg gratings for encoding/decoding of unipolar m -sequence codes, and balanced detection. The bit-error rate is measured for up to four simultaneous users at 155 and 622 Mb/s. Exploiting the excellent match between simulation and experiment, the paper concludes with a prediction of the potential capacity of an optimized FE-CDMA system.

Performance Analysis of Spectral-Phase-Encoded Optical CDMA System Using Two-Photon-Absorption Receiver Structure for Asynchronous and Slot-Level Synchronous Transmitters

Science.gov (United States)

Jamshidi, Kambiz; Salehi, Jawad A.

2007-06-01

In this paper, we analyze the performance of a nonlinear two-photon-absorption (TPA) receiver and compare its performance with that of a single-photon-absorption (SPA) receiver in the context of spectral-phase-encoded optical code-division multiple access (CDMA) technique. The performances for the above systems are evaluated for two different transmission scenarios, namely, asynchronous and slot-level synchronous transmitters. Performance evaluation includes different sources of degradation such as multiple-access interference, noise due to optical amplification, shot noise, and thermal noise. In obtaining the performance, the mean and variance of the received signal in each of the above techniques are derived, and bit error rate is obtained using Gaussian approximation. In general, it is shown that TPA receivers are superior in performance with respect to SPA receivers when the receiver employs a much slower photodetector in comparison with the laser's transmitted pulse duration. This, indeed, is the reason behind the choice of nonlinear receivers, such as TPA, in most spectral-phase-encoded optical CDMA systems.

A Mitigation Technique of High-Power MAI in the Multimedia Optical CDMA System with the Optical Power Selector

Science.gov (United States)

Ohba, Kohki; Miyazawa, Takaya; Sasase, Iwao

In this paper, we propose a mitigation system of high-level multiple access interference (MAI) for multimedia optical Code-Division Multiple-Access (CDMA) systems using the optical power selector (OPS). The proposed system can eliminate high-intensity MAI at the receiver for low-priority users. Moreover, the proposed system can reduce by half the required number of code sequences compared to the conventional scheme. As a result, the proposed system can increase the number of weights at the same code-length and, thus, obtain higher code spreading gain. We analyze performances of the proposed system and show that both high-priority users and low-priority users achieve lower bit error rates in comparison to the conventional scheme.

CP decomposition approach to blind separation for DS-CDMA system using a new performance index

Science.gov (United States)

Rouijel, Awatif; Minaoui, Khalid; Comon, Pierre; Aboutajdine, Driss

2014-12-01

In this paper, we present a canonical polyadic (CP) tensor decomposition isolating the scaling matrix. This has two major implications: (i) the problem conditioning shows up explicitly and could be controlled through a constraint on the so-called coherences and (ii) a performance criterion concerning the factor matrices can be exactly calculated and is more realistic than performance metrics used in the literature. Two new algorithms optimizing the CP decomposition based on gradient descent are proposed. This decomposition is illustrated by an application to direct-sequence code division multiplexing access (DS-CDMA) systems; computer simulations are provided and demonstrate the good behavior of these algorithms, compared to others in the literature.

Selective Adaptive Parallel Interference Cancellation for Multicarrier DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Ahmed El-Sayed El-Mahdy

2013-07-01

Full Text Available In this paper, Selective Adaptive Parallel Interference Cancellation (SA-PIC technique is presented for Multicarrier Direct Sequence Code Division Multiple Access (MC DS-CDMA scheme. The motivation of using SA-PIC is that it gives high performance and at the same time, reduces the computational complexity required to perform interference cancellation. An upper bound expression of the bit error rate (BER for the SA-PIC under Rayleigh fading channel condition is derived. Moreover, the implementation complexities for SA-PIC and Adaptive Parallel Interference Cancellation (APIC are discussed and compared. The performance of SA-PIC is investigated analytically and validated via computer simulations.

Symbol and Bit Error Rates Analysis of Hybrid PIM-CDMA

Directory of Open Access Journals (Sweden)

Ghassemlooy Z

2005-01-01

Full Text Available A hybrid pulse interval modulation code-division multiple-access (hPIM-CDMA scheme employing the strict optical orthogonal code (SOCC with unity and auto- and cross-correlation constraints for indoor optical wireless communications is proposed. In this paper, we analyse the symbol error rate (SER and bit error rate (BER of hPIM-CDMA. In the analysis, we consider multiple access interference (MAI, self-interference, and the hybrid nature of the hPIM-CDMA signal detection, which is based on the matched filter (MF. It is shown that the BER/SER performance can only be evaluated if the bit resolution conforms to the condition set by the number of consecutive false alarm pulses that might occur and be detected, so that one symbol being divided into two is unlikely to occur. Otherwise, the probability of SER and BER becomes extremely high and indeterminable. We show that for a large number of users, the BER improves when increasing the code weight . The results presented are compared with other modulation schemes.

An analytical model for CDMA downlink rate optimization taking into account uplink coverage restriction

NARCIS (Netherlands)

Endrayanto, A.I.; van den Berg, Hans Leo; Boucherie, Richardus J.

2003-01-01

This paper models and analyzes downlink and uplink power assignment in Code Division Multiple Access (CDMA) mobile networks. By discretizing the area into small segments, the power requirements are characterized via a matrix representation that separates user and system characteristics. We obtain a

An analytical model for CDMA downlink rate optimization taking into account uplink coverage restrictions

NARCIS (Netherlands)

Endrayanto, A.I.; van den Berg, Hans Leo; Boucherie, Richardus J.

2005-01-01

This paper models and analyzes downlink and uplink power assignment in code division multiple access (CDMA) mobile networks. By discretizing the area into small segments, the power requirements are characterized via a matrix representation that separates user and system characteristics. We obtain a

Quadrature amplitude modulation from basics to adaptive trellis-coded turbo-equalised and space-time coded OFDM CDMA and MC-CDMA systems

CERN Document Server

Hanzo, Lajos

2004-01-01

"Now fully revised and updated, with more than 300 pages of new material, this new edition presents the wide range of recent developments in the field and places particular emphasis on the family of coded modulation aided OFDM and CDMA schemes. In addition, it also includes a fully revised chapter on adaptive modulation and a new chapter characterizing the design trade-offs of adaptive modulation and space-time coding." "In summary, this volume amalgamates a comprehensive textbook with a deep research monograph on the topic of QAM, ensuring it has a wide-ranging appeal for both senior undergraduate and postgraduate students as well as practicing engineers and researchers."--Jacket.

Dispersion Compensation Requirements for Optical CDMA Using WDM Lasers

International Nuclear Information System (INIS)

Mendez, A J; Hendandez, V J; Feng, H X C; Heritage, J P; Lennon, W J

2001-01-01

Optical code division multiple access (O-CDMA) uses very narrow transmission pulses and is thus susceptible to fiber optic link impairments. When the O-CDMA is implemented as wavelength/time (W/T) matrices which use wavelength division multiplexing (WDM) sources such as multi-frequency laser transmitters, the susceptibility may be higher due to: (a) the large bandwidth utilized and (b) the requirement that the various wavelength components of the codes be synchronized at the point of modulation and encoding as well as after (optical) correlation. A computer simulation based on the nonlinear Schroedinger equation, developed to study optical networking on the National Transparent Optical Network (NTON), was modified to characterize the impairments on the propagation and decoding of W/T matrix codes over a link of the NTON. Three critical link impairments were identified by the simulation: group velocity dispersion (GVD); the flatness of the optical amplifier gain; and the slope of the GVD. Subsequently, experiments were carried out on the NTON link to verify and refine the simulations as well as to suggest improvements in the W/T matrix signal processing design. The NTON link measurements quantified the O-CDMA dispersion compensation requirements. Dispersion compensation management is essential to assure the performance of W/T matrix codes

A multiple-choice knapsack based algorithm for CDMA downlink rate differentiation under uplink coverage restrictions

NARCIS (Netherlands)

Endrayanto, A.I.; Bumb, A.F.; Boucherie, Richardus J.

2004-01-01

This paper presents an analytical model for downlink rate allocation in Code Division Multiple Access (CDMA) mobile networks. By discretizing the coverage area into small segments, the transmit power requirements are characterized via a matrix representation that separates user and system

An Improved Overloading Scheme for Downlink CDMA

Directory of Open Access Journals (Sweden)

Marc Moeneclaey

2005-04-01

Full Text Available An improved overloading scheme is presented for single-user detection in the downlink of multiple-access systems based on OCDMA/OCDMA (O/O. By displacing in time the orthogonal signatures of the two user sets that make up the overloaded system, the cross-correlation between the users of the two sets is reduced. For random O/O with square-root cosine rolloff chip pulses, the multiuser interference can be decreased by up to 50% (depending on the chip pulse bandwidth as compared to quasiorthogonal sequences (QOS that are presently part of the downlink standard of Cdma2000. This reduction of the multiuser interference gives rise to an increase of the achievable signal-to-interference-plus-noise ratio for a particular channel load.

A satellite mobile communication system based on Band-Limited Quasi-Synchronous Code Division Multiple Access (BLQS-CDMA)

Science.gov (United States)

Degaudenzi, R.; Elia, C.; Viola, R.

1990-01-01

Discussed here is a new approach to code division multiple access applied to a mobile system for voice (and data) services based on Band Limited Quasi Synchronous Code Division Multiple Access (BLQS-CDMA). The system requires users to be chip synchronized to reduce the contribution of self-interference and to make use of voice activation in order to increase the satellite power efficiency. In order to achieve spectral efficiency, Nyquist chip pulse shaping is used with no detection performance impairment. The synchronization problems are solved in the forward link by distributing a master code, whereas carrier forced activation and closed loop control techniques have been adopted in the return link. System performance sensitivity to nonlinear amplification and timing/frequency synchronization errors are analyzed.

Combined Effect of Random Transmit Power Control and Inter-Path Interference Cancellation on DS-CDMA Packet Mobile Communications

Science.gov (United States)

Kudoh, Eisuke; Ito, Haruki; Wang, Zhisen; Adachi, Fumiyuki

In mobile communication systems, high speed packet data services are demanded. In the high speed data transmission, throughput degrades severely due to severe inter-path interference (IPI). Recently, we proposed a random transmit power control (TPC) to increase the uplink throughput of DS-CDMA packet mobile communications. In this paper, we apply IPI cancellation in addition to the random TPC. We derive the numerical expression of the received signal-to-interference plus noise power ratio (SINR) and introduce IPI cancellation factor. We also derive the numerical expression of system throughput when IPI is cancelled ideally to compare with the Monte Carlo numerically evaluated system throughput. Then we evaluate, by Monte-Carlo numerical computation method, the combined effect of random TPC and IPI cancellation on the uplink throughput of DS-CDMA packet mobile communications.

Experimental demonstration of all-optical CDMA using bipolar codes

Science.gov (United States)

Dennis, Tasshi

1999-10-01

Fiber optic networks capable of supporting a large pool of subscribers, many simultaneous users, and high data rates are receiving heightened interest as solutions to a growing communications need. The experiments reported in this study constitute the first experimental demonstration of a novel bipolar equivalent code-division multiple-access (CDMA) scheme. The sophisticated encoding increases noise tolerance, provides user security, and enables network flexibility. The scheme is based on an established bipolar radio frequency (RF) technique adapted to the unipolar optical domain. Whereas the phase of an RF signal can be readily detected, the high carrier frequency ( ~ 200 THz at 1.5 μm) of an optical wave necessitates that optical signals be detected and processed solely by intensity. Asynchronous operation makes the CDMA scheme data rate independent, while all-optical implementation avoids the bandwidth limitations imposed by electrical processing. A proof-of-principle experiment was conducted by spectrally encoding an erbium-doped superfluorescent fiber source (SFS) using a diffraction grating and an amplitude mask. The optical properties of the system were measured and the bipolar correlation of codes was verified. The practical implementation of the scheme was investigated by the design, construction, and operation of a fiber-based testbed. Correlation measurements performed with modulated signals confirmed that the scheme can recover a binary information symbol while rejecting multiple access interference. A theoretical analysis of the optical correlation process was conducted, which identified key optical parameters important to future implementations. The theory of excess noise associated with the photodetection of a thermal source was considered, followed by noise measurements of a light bulb and the erbium-doped SFS used for spectral encoding. Finally, the ability of the proposed scheme to effectively transmit data was investigated. Signal-to- noise

First satellite mobile communication trials using BLQS-CDMA

Science.gov (United States)

Luzdemateo, Maria; Johns, Simon; Dothey, Michel; Vanhimbeeck, Carl; Deman, Ivan; Wery, Bruno

1993-01-01

In this paper, technical results obtained in the first MSBN Land mobile technical trial are reported. MSBN (Mobile Satellite Business Network) is a new program undertaken by the European Space Agency (ESA) to promote mobile satellite communication in Europe, in particular voice capability. The first phase of the MSBN system implementation plan is an experimental phase. Its purpose is to evaluate through field experiments the performance of the MSBN system prior to finalization of its specifications. Particularly, the objective is to verify in the field and possibly improve the performance of the novel satellite access technique BLQS-CDMA (Band Limited Quasi-Synchronous-Code Division Multiple Access), which is proposed as baseline for the MSBN.

The Study of MSADQ/CDMA Protocol in Voice/Data Integration Packet Networks

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

A new packet medium access protocol, namely, minislot signalingaccess based on distributed queues(MSADQ/CDMA), is proposed in voice and data intergration CDMA networks. The MSADQ protocol is based on distributed queues and collision resolution algorithm. Through proper management of the PN codes, the number of random competition collision reduces greatly, the multiple access interference (MAI) decreases. It has several special access signaling channels to carry the voice and data access request. Each slot is devided into several control minislots (CMSs), in which the Data Terminals (DT) or Voice Terminals (VT) transmit their request. According to the voice and data traffic character, the signaling access structure is proposed. The code assign rules and queue managing rules are also proposed to ensure the QoS requirement of each traffic. Comparisions with other three protocol are developed by simulation, which shows that MSADQ/CDMA protocol occupies less PN codes, but still has very good performance.

On Intercell Interference and Its Cancellation in Cellular Multicarrier CDMA Systems

Directory of Open Access Journals (Sweden)

Plass Simon

2008-01-01

Full Text Available Abstract The handling of intercell interference at the cell border area is a strong demand in future communication systems to guarantee efficient use of the available bandwidth. Therefore, this paper focuses on the application of iterative intercell interference cancellation schemes in cellular multicarrier code division multiple access (MC-CDMA systems at the receiver side for the downlink. First, the influence of the interfering base stations to the total intercell interference is investigated. Then, different concepts for intercell interference cancellation are described and investigated for scenarios with several interfering cells. The first approach is based on the use of the hard decision of the demodulator to reconstruct the received signals. This does not require the higher amount of complexity compared to the second approach which is based on the use of the more reliable soft values from the decoding process. Furthermore, the extrinsic information as a reliability measure of this soft iterative cancellation process is investigated in more detail based on the geographical position of the mobile terminal. Both approaches show significant performance gains in the severe cell border area. With the soft intercell interference cancellation scheme, it is possible to reach the single-user bound. Therefore, the intercell interference can be almost eliminated.

Throughput performance analysis of multirate, multiclass S-ALOHA OFFH-CDMA packet networks

DEFF Research Database (Denmark)

Raddo, Thiago R.; Sanches, Anderson L.; Borges, Ben Hur V

2015-01-01

In this paper, we propose a new throughput expression for multirate, multiclass slotted-ALOHA optical fast frequency hopping code-division multiple-access (OFFH-CDMA) packet networks considering a Poisson distribution for packet composite arrivals. We analyze the packet throughput performance...... of a three-class OFFH-CDMA network, where multirate transmissions are achieved via manipulation of the user's code parameters. It is shown that users transmitting at low rates interfere considerably in the performance of high rate users. Finally, we perform a validation procedure to demonstrate...

Pilot-Assisted Channel Estimation for Orthogonal Multi-Carrier DS-CDMA with Frequency-Domain Equalization

Science.gov (United States)

Shima, Tomoyuki; Tomeba, Hiromichi; Adachi, Fumiyuki

Orthogonal multi-carrier direct sequence code division multiple access (orthogonal MC DS-CDMA) is a combination of time-domain spreading and orthogonal frequency division multiplexing (OFDM). In orthogonal MC DS-CDMA, the frequency diversity gain can be obtained by applying frequency-domain equalization (FDE) based on minimum mean square error (MMSE) criterion to a block of OFDM symbols and can improve the bit error rate (BER) performance in a severe frequency-selective fading channel. FDE requires an accurate estimate of the channel gain. The channel gain can be estimated by removing the pilot modulation in the frequency domain. In this paper, we propose a pilot-assisted channel estimation suitable for orthogonal MC DS-CDMA with FDE and evaluate, by computer simulation, the BER performance in a frequency-selective Rayleigh fading channel.

GLONASS CDMA L3 ambiguity resolution and positioning

NARCIS (Netherlands)

Zaminpardaz, Safoora; Teunissen, P.J.G.; Nadarajah, Nandakumaran

2016-01-01

A first assessment of GLONASS CDMA L3 ambiguity resolution and positioning performance is provided. Our analyses are based on GLONASS L3 data from the satellite pair SVNs 755-801, received by two JAVAD receivers at Curtin University, Perth, Australia. In our analyses, four different versions of

Performance Analysis of Blind Subspace-Based Signature Estimation Algorithms for DS-CDMA Systems with Unknown Correlated Noise

Science.gov (United States)

Zarifi, Keyvan; Gershman, Alex B.

2006-12-01

We analyze the performance of two popular blind subspace-based signature waveform estimation techniques proposed by Wang and Poor and Buzzi and Poor for direct-sequence code division multiple-access (DS-CDMA) systems with unknown correlated noise. Using the first-order perturbation theory, analytical expressions for the mean-square error (MSE) of these algorithms are derived. We also obtain simple high SNR approximations of the MSE expressions which explicitly clarify how the performance of these techniques depends on the environmental parameters and how it is related to that of the conventional techniques that are based on the standard white noise assumption. Numerical examples further verify the consistency of the obtained analytical results with simulation results.

Blind Reduced-Rank MMSE Detector for DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Xiaodong Cai

2003-01-01

Full Text Available We first develop a reduced-rank minimum mean squared error (MMSE detector for direct-sequence (DS code division multiple access (CDMA by forcing the linear MMSE detector to lie in a signal subspace of a reduced dimension. While a reduced-rank MMSE detector has lower complexity, it cannot outperform the full-rank MMSE detector. We then concentrate on the blind reduced-rank MMSE detector which is obtained from an estimated covariance matrix. Our analysis and simulation results show that when the desired user′s signal is in a low-dimensional subspace, there exists an optimal subspace so that the blind reduced-rank MMSE detector lying in this subspace has the best performance. By properly choosing a subsspace, we guarantee that the optimal blind reduced-rank MMSE detector is obtained. An adaptive blind reduced-rank MMSE detector, based on a subspace tracking algorithm, is developed. The adaptive blind reduced-rank MMSE detector exhibits superior steady-state performance and fast convergence speed.

Cellular responses to 836 MHz and 1,765 GHz CDMA radiations

International Nuclear Information System (INIS)

Park, Woong Yang; Seo, Jeong Sun; Paik, Jung Ki; Lim, Kye Jae; Yoon, Hyun Bo

2002-01-01

The effect of radiofrequency (RF) radiation in the cellular phone communication range (836.5 MHz and 1.765 GHz code division multiple access, CDMA) on tumorigenesis and other health effect was measured using the in vitro cell culture system. To determine whether 836.5 MHz or 1.765 GHz CDMA radiations have any genotoxic effects to induce neoplastic transformation, C3H 10T1/2 cells were exposed to either of the above radiations at a specific absorption rate (SAR) of 35.6W/Kg (836.5 MHz) and 38.2 W/kg(1.765 GHz) or sham- exposed at the same time for 7 days. Cells were maintained in incubators and refed with fresh growth medium every 3 days. At this SAR, radiofrequency radiation did not induce neoplastic transformation in vitro. The extent of alteration in the kinetics of cell proliferation indicated no significant differences between RF-radiation- and sham-exposed cells with respect to MTS assay and 8-OHdG. Under this experimental conditions tested, there is no evidence for the induction of genotoxic indices in human and mouse cells exposed in vitro for 7 days to 836.5 MHz or 1.765 GHz RF radiation at SARs of up to 35.6 or 38.2 W/kg

Performance Analysis of Iterative Channel Estimation and Multiuser Detection in Multipath DS-CDMA Channels

Science.gov (United States)

Li, Husheng; Betz, Sharon M.; Poor, H. Vincent

2007-05-01

This paper examines the performance of decision feedback based iterative channel estimation and multiuser detection in channel coded aperiodic DS-CDMA systems operating over multipath fading channels. First, explicit expressions describing the performance of channel estimation and parallel interference cancellation based multiuser detection are developed. These results are then combined to characterize the evolution of the performance of a system that iterates among channel estimation, multiuser detection and channel decoding. Sufficient conditions for convergence of this system to a unique fixed point are developed.

Timing-Free Blind Multiuser Detection for Multicarrier DS/CDMA Systems with Multiple Antennae

Directory of Open Access Journals (Sweden)

Stefano Buzzi

2004-05-01

Full Text Available The problem of blind multiuser detection for an asynchronous multicarrier DS-CDMA system employing multiple transmit and receive antennae over a Rayleigh fading channel is considered in this paper. The solutions that we develop require prior knowledge of the spreading code of the user to be decoded only, while no further information either on the user to be decoded or on the other active users is required. Several combining rules for the observables at the output of each receive antenna are proposed and assessed, and the implications of the different options are studied in depth in terms of both detection performance and computational complexity. A closed form expression is also derived for the conditional error probability and a lower bound for the near-far resistance is provided. Results confirm that the proposed blind receivers can cope with both multiple access interference suppression and channel estimation at the price of a limited performance loss as compared to the ideal linear receivers which assume perfect channel state information.

Adaptive Iterative Soft-Input Soft-Output Parallel Decision-Feedback Detectors for Asynchronous Coded DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Zhang Wei

2005-01-01

Full Text Available The optimum and many suboptimum iterative soft-input soft-output (SISO multiuser detectors require a priori information about the multiuser system, such as the users' transmitted signature waveforms, relative delays, as well as the channel impulse response. In this paper, we employ adaptive algorithms in the SISO multiuser detector in order to avoid the need for this a priori information. First, we derive the optimum SISO parallel decision-feedback detector for asynchronous coded DS-CDMA systems. Then, we propose two adaptive versions of this SISO detector, which are based on the normalized least mean square (NLMS and recursive least squares (RLS algorithms. Our SISO adaptive detectors effectively exploit the a priori information of coded symbols, whose soft inputs are obtained from a bank of single-user decoders. Furthermore, we consider how to select practical finite feedforward and feedback filter lengths to obtain a good tradeoff between the performance and computational complexity of the receiver.

Code-division multiple-access protocol for active RFID systems

Science.gov (United States)

Mazurek, Gustaw; Szabatin, Jerzy

2008-01-01

Most of the Radio Frequency Identification (RFID) systems operating in HF and UHF bands employ narrowband modulations (FSK or ASK) with Manchester coding. However, these simple transmission schemes are vulnerable to narrowband interference (NBI) generated by other radio systems working in the same frequency band, and also suffer from collision problem and need special anti-collision procedures. This becomes especially important when operating in a noisy, crowded industrial environment. In this paper we show the performance of RFID system with DS-CDMA transmission in comparison to a standard system with FSK modulation defined in ISO 18000-7. Our simulation results show that without any bandwidth expansion the immunity against NBI can be improved by 8 dB and the system capacity can be 7 times higher when using DS-CDMA transmission instead of FSK modulation with Manchester coding.

A CDMA multiuser detection algorithm on the basis of belief propagation

International Nuclear Information System (INIS)

Kabashima, Yoshiyuki

2003-01-01

An iterative algorithm for the multiuser detection problem that arises in code division multiple access (CDMA) systems is developed on the basis of Pearl's belief propagation (BP). We show that the BP-based algorithm exhibits nearly optimal performance in a practical time scale by utilizing the central limit theorem and self-averaging property appropriately, whereas direct application of BP to the detection problem is computationally difficult and far from practical. We further present close relationships of the proposed algorithm to the Thouless-Anderson-Palmer approach and replica analysis known in spin-glass research

SIMULASI TEKNIK POWER CONTROL DAN MULTI USER DETECTION PADA SISTEM KOMUNIKASI DS-CDMA

Directory of Open Access Journals (Sweden)

Yuli Christyono

2012-02-01

Full Text Available CDMA is interference limited multiple access system. Because all users transmit on the same frequency,internal interference generated by the system is the most significant factor in determining system capacity andcall quality. The transmit power for each user must be reduced to limit interference, however, the power shouldbe enough to maintain the required Eb/No (signal to noise ratio for a satisfactory call quality. Maximumcapacity is achieved when Eb/No of every user is at the minimum level needed for the acceptable channelperformance. As the MS moves around, the RF environment continuously changes due to fast and slow fading,external interference, shadowing , and other factors. The aim of the dynamic power control is to limittransmitted power on both the links while maintaining link quality under all conditions. Additional advantagesare longer mobile battery life and longer life span of BTS power amplifiers.In this research will be made a sumulation of power control and multi user detection to avoid the interferencebetween MS.Observations show that the increasing number of users will decrease the value of Signal to Interfrence Ratio(SIR / SIR below the target. To cope the growing number of users increases can be done by iteration / updatingpower transmit so the convergence computation can be reached and target value SIR can be achieved. Inaddition, to reduce interference can also be done by extending the number of chips.

Improved Fiber Bragg Grating Array OFFH-CDMA System Using a Novel Frequency-Overlapping Multigroup Method

Science.gov (United States)

Peng, Wei-Ren; Lin, Wen-Piao; Chi, Sien

2006-03-01

The authors propose a novel frequency-overlapping multigroup scheme for a passive all-optical fast-frequency hopped code-division multiple-access (OFFH-CDMA) system based on fiber Bragg grating array (FBGA). In the conventional scheme, the users are assigned those codes constructed on the nonoverlapping frequency slots, and therefore the bandgaps between the adjacent gratings are wasted. To make a more efficient use of the optical spectrum, the proposed scheme divided the users into several groups, and assigned the codes, which interleaved to each other to the different groups. In addition to the higher utilization of the spectrum, the interleaved nature of the frequency allocations of different groups will make the groups less correlated and, hence, lower the multiple-access interference (MAI). The corresponding codeset and its constraints for this new scheme are also developed and analyzed. The performance of the system in terms of the correlation functions and bit error rate (BER) are given in both the conventional and the proposed schemes. The numerical results show that, with the multigroup scheme, performance is much improved compared to the conventional scheme.

Cross-Layer Resource Allocation for Variable Bit Rate Multiclass Services in a Multirate Multicarrier DS-CDMA Network

Directory of Open Access Journals (Sweden)

Kee-Chaing Chua

2005-02-01

Full Text Available An approximate analytical formulation of the resource allocation problem for handling variable bit rate multiclass services in a cellular round-robin carrier-hopping multirate multicarrier direct-sequence code-division multiple-access (MC-DS-CDMA system is presented. In this paper, all grade-of-service (GoS or quality-of-service (QoS requirements at the connection level, packet level, and link layer are satisfied simultaneously in the system, instead of being satisfied at the connection level or at the link layer only. The analytical formulation shows how the GoS/QoS in the different layers are intertwined across the layers. A novelty of this paper is that the outages in the subcarriers are minimized by spreading the subcarriers' signal-to-interference ratio evenly among all the subcarriers by using a dynamic round-robin carrier-hopping allocation scheme. A complete sharing (CS scheme with guard capacity is used for the resource sharing policy at the connection level based on the mean rates of the connections. Numerical results illustrate that significant gain in the system utilization is achieved through the joint coupling of connection/packet levels and link layer.

FPGA Implementation of Block Parallel DF-MPIC Detectors for DS-CDMA Systems in Frequency-Nonselective Channels

Directory of Open Access Journals (Sweden)

Adel Omar Dahmane

2008-01-01

Full Text Available Multistage parallel interference cancellation- (MPIC- based detectors allow to mitigate multiple-access interference in direct-sequence code-division multiple-access (DS-CDMA systems. They are considered serious candidates for practical implementation showing a good tradeoff between performance and complexity. Better performance is obtained when decision feedback (DF is employed. Although MPIC and DF-MPIC have the same arithmetic complexity, DF-MPIC needs much more FPGA resources when compared to MPIC without decision feedback. In this letter, FPGA implementation of block parallel DF-MPIC (BP-DF-MPIC is proposed allowing better tradeoff between performance and FPGA area occupancy. To reach an uncoded bit-error rate of 10−3, BP-DF-MPIC shows a 1.5 dB improvement over the MPIC without decision feedback with only 8% increase in FPGA resources compared to 69% for DF-MPIC.

Reduction of the near-far effect in mobile communication systems with Code-Division Multiple-Access

Science.gov (United States)

Purchla, Magdalena

2006-02-01

In this paper the basic methods for reducing Multiple Access Interference (MAI) and combating the near-far effect in Direct-Sequence Code-Division Multiple-Access (DS-CDMA) mobile communication systems are presented. MAI and the near-far effect are inevitable in DS-CDMA systems with quasi-orthogonal spreading sequences. An effective method of reducing MAI can increase the capacity of the system that is why so many researchers are working in this field. In this article three most important techniques of decreasing MAI are presented: power control, multiuser detection and space-time processing. There is a short introduction to each topic and one or more examples found in literature of algorithms suitable for practical applications (although not all algorithms are yet used in existing systems).

On the Capacity of a Cellular CDMA System Reverse Channel

National Research Council Canada - National Science Library

Klitorakis, Petros

2002-01-01

.... The performance of the system is examined under several values of the standard deviation of lognormal shadowing and the power control error for various numbers of users and values of the Nakagami-m variable by using simulations. Finally, a barrage noise jammer will be introduced and its effect seen in the performance of the cellular communication system for a specific value of E(sub b)/N(sub o).

Equalization of Multiuser Wireless CDMA Downlink Considering Transmitter Nonlinearity Using Walsh Codes

Directory of Open Access Journals (Sweden)

Pinter Stephen Z

2007-01-01

Full Text Available Transmitter nonlinearity has been a major issue in many scenarios: cellular wireless systems have high power RF amplifier (HPA nonlinearity at the base station; satellite downlinks have nonlinear TWT amplifiers in the satellite transponder and multipath conditions in the ground station; and radio-over-fiber (ROF systems consist of a nonlinear optical link followed by a wireless channel. In many cases, the nonlinearity is simply ignored if there is no out-of-band emission. This results in poor BER performance. In this paper we propose a new technique to estimate the linear part of the wireless downlink in the presence of a nonlinearity using Walsh codes; Walsh codes are commonly used in CDMA downlinks. Furthermore, we show that equalizer performance is significantly improved by taking into account the presence of the nonlinearity during channel estimation. This is shown by using a regular decision feedback equalizer (DFE with both wireless and RF amplifier noise. We perform estimation in a multiuser CDMA communication system where all users transmit their signal simultaneously. Correlation analysis is applied to identify the channel impulse response (CIR and the derivation of key correlation relationships is shown. A difficulty with using Walsh codes in terms of their correlations (compared to PN sequences is then presented, as well as a discussion on how to overcome it. Numerical evaluations show a good estimation of the linear system with 54 users in the downlink and a signal-to-noise ratio (SNR of 25 dB. Bit error rate (BER simulations of the proposed identification and equalization algorithms show a BER of achieved at an SNR of dB.

Performance Analysis for Bit Error Rate of DS- CDMA Sensor Network Systems with Source Coding

Directory of Open Access Journals (Sweden)

Haider M. AlSabbagh

2012-03-01

Full Text Available The minimum energy (ME coding combined with DS-CDMA wireless sensor network is analyzed in order to reduce energy consumed and multiple access interference (MAI with related to number of user(receiver. Also, the minimum energy coding which exploits redundant bits for saving power with utilizing RF link and On-Off-Keying modulation. The relations are presented and discussed for several levels of errors expected in the employed channel via amount of bit error rates and amount of the SNR for number of users (receivers.

Mobile Position Estimation using Artificial Neural Network in CDMA Cellular Systems

Directory of Open Access Journals (Sweden)

Omar Waleed Abdulwahhab

2017-01-01

Full Text Available Using the Neural network as a type of associative memory will be introduced in this paper through the problem of mobile position estimation where mobile estimate its location depending on the signal strength reach to it from several around base stations where the neural network can be implemented inside the mobile. Traditional methods of time of arrival (TOA and received signal strength (RSS are used and compared with two analytical methods, optimal positioning method and average positioning method. The data that are used for training are ideal since they can be obtained based on geometry of CDMA cell topology. The test of the two methods TOA and RSS take many cases through a nonlinear path that MS can move through that region. The results show that the neural network has good performance compared with two other analytical methods which are average positioning method and optimal positioning method.

Electromagnetic Interference Assessment of CDMA and GSM Wireless Phones to Aircraft Navigation Radios

Science.gov (United States)

Ely, Jay J.; Nguyen, Truong X.; Koppen, Sandra V.; Salud, M. Theresa

2002-01-01

To address the concern for cellular phone electromagnetic interference (EMI) to aircraft radios, a radiated emission measurement process for CDMA (IS-95) and GSM (ETSI GSM 11.22) wireless handsets was developed. Spurious radiated emissions were efficiently characterized from devices tested in either a semi-anechoic or reverberation chamber, in terms of effective isotropic radiated power. Eight representative handsets (4 GSM, 4 CDMA) were commanded to operate while varying their radio transmitter parameters (power, modulation, etc.). This report provides a detailed description of the measurement process and resulting data, which may subsequently be used by others as a basis of consistent evaluation for cellular/PCS phones, Bluetooth, IEEE802.11b, IEEE802.11a, FRS/GMRS radios, and other portable transmitters. Aircraft interference path loss (IPL) and navigation radio interference threshold data from numerous reference documents, standards, and NASA partnerships were compiled. Using this data, a preliminary risk assessment is provided for CDMA and GSM wireless phone interference to aircraft localizer, Glideslope, VOR, and GPS radio receivers on typical transport airplanes. The report identifies where existing data for device emissions, IPL, and navigation radio interference thresholds needs to be extended for an accurate risk assessment for wireless transmitters in aircraft.

A Chip-Level BSOR-Based Linear GSIC Multiuser Detector for Long-Code CDMA Systems

Directory of Open Access Journals (Sweden)

Benyoucef M

2007-01-01

Full Text Available We introduce a chip-level linear group-wise successive interference cancellation (GSIC multiuser structure that is asymptotically equivalent to block successive over-relaxation (BSOR iteration, which is known to outperform the conventional block Gauss-Seidel iteration by an order of magnitude in terms of convergence speed. The main advantage of the proposed scheme is that it uses directly the spreading codes instead of the cross-correlation matrix and thus does not require the calculation of the cross-correlation matrix (requires floating point operations (flops, where is the processing gain and is the number of users which reduces significantly the overall computational complexity. Thus it is suitable for long-code CDMA systems such as IS-95 and UMTS where the cross-correlation matrix is changing every symbol. We study the convergence behavior of the proposed scheme using two approaches and prove that it converges to the decorrelator detector if the over-relaxation factor is in the interval ]0, 2[. Simulation results are in excellent agreement with theory.

A Chip-Level BSOR-Based Linear GSIC Multiuser Detector for Long-Code CDMA Systems

Directory of Open Access Journals (Sweden)

M. Benyoucef

2008-01-01

Full Text Available We introduce a chip-level linear group-wise successive interference cancellation (GSIC multiuser structure that is asymptotically equivalent to block successive over-relaxation (BSOR iteration, which is known to outperform the conventional block Gauss-Seidel iteration by an order of magnitude in terms of convergence speed. The main advantage of the proposed scheme is that it uses directly the spreading codes instead of the cross-correlation matrix and thus does not require the calculation of the cross-correlation matrix (requires 2NK2 floating point operations (flops, where N is the processing gain and K is the number of users which reduces significantly the overall computational complexity. Thus it is suitable for long-code CDMA systems such as IS-95 and UMTS where the cross-correlation matrix is changing every symbol. We study the convergence behavior of the proposed scheme using two approaches and prove that it converges to the decorrelator detector if the over-relaxation factor is in the interval ]0, 2[. Simulation results are in excellent agreement with theory.

A Robust Parametric Technique for Multipath Channel Estimation in the Uplink of a DS-CDMA System

Directory of Open Access Journals (Sweden)

2006-01-01

Full Text Available The problem of estimating the multipath channel parameters of a new user entering the uplink of an asynchronous direct sequence-code division multiple access (DS-CDMA system is addressed. The problem is described via a least squares (LS cost function with a rich structure. This cost function, which is nonlinear with respect to the time delays and linear with respect to the gains of the multipath channel, is proved to be approximately decoupled in terms of the path delays. Due to this structure, an iterative procedure of 1D searches is adequate for time delays estimation. The resulting method is computationally efficient, does not require any specific pilot signal, and performs well for a small number of training symbols. Simulation results show that the proposed technique offers a better estimation accuracy compared to existing related methods, and is robust to multiple access interference.

A Joint Optimization Criterion for Blind DS-CDMA Detection

Directory of Open Access Journals (Sweden)

Sergio A. Cruces-Alvarez

2007-01-01

Full Text Available This paper addresses the problem of the blind detection of a desired user in an asynchronous DS-CDMA communications system with multipath propagation channels. Starting from the inverse filter criterion introduced by Tugnait and Li in 2001, we propose to tackle the problem in the context of the blind signal extraction methods for ICA. In order to improve the performance of the detector, we present a criterion based on the joint optimization of several higher-order statistics of the outputs. An algorithm that optimizes the proposed criterion is described, and its improved performance and robustness with respect to the near-far problem are corroborated through simulations. Additionally, a simulation using measurements on a real software-radio platform at 5 GHz has also been performed.

A Joint Optimization Criterion for Blind DS-CDMA Detection

Science.gov (United States)

Durán-Díaz, Iván; Cruces-Alvarez, Sergio A.

2006-12-01

This paper addresses the problem of the blind detection of a desired user in an asynchronous DS-CDMA communications system with multipath propagation channels. Starting from the inverse filter criterion introduced by Tugnait and Li in 2001, we propose to tackle the problem in the context of the blind signal extraction methods for ICA. In order to improve the performance of the detector, we present a criterion based on the joint optimization of several higher-order statistics of the outputs. An algorithm that optimizes the proposed criterion is described, and its improved performance and robustness with respect to the near-far problem are corroborated through simulations. Additionally, a simulation using measurements on a real software-radio platform at 5 GHz has also been performed.

Performance of a Two-Level Call Admission Control Scheme for DS-CDMA Wireless Networks

Directory of Open Access Journals (Sweden)

Fapojuwo Abraham O

2007-01-01

Full Text Available We propose a two-level call admission control (CAC scheme for direct sequence code division multiple access (DS-CDMA wireless networks supporting multimedia traffic and evaluate its performance. The first-level admission control assigns higher priority to real-time calls (also referred to as class 0 calls in gaining access to the system resources. The second level admits nonreal-time calls (or class 1 calls based on the resources remaining after meeting the resource needs for real-time calls. However, to ensure some minimum level of performance for nonreal-time calls, the scheme reserves some resources for such calls. The proposed two-level CAC scheme utilizes the delay-tolerant characteristic of non-real-time calls by incorporating a queue to temporarily store those that cannot be assigned resources at the time of initial access. We analyze and evaluate the call blocking, outage probability, throughput, and average queuing delay performance of the proposed two-level CAC scheme using Markov chain theory. The analytic results are validated by simulation results. The numerical results show that the proposed two-level CAC scheme provides better performance than the single-level CAC scheme. Based on these results, it is concluded that the proposed two-level CAC scheme serves as a good solution for supporting multimedia applications in DS-CDMA wireless communication systems.

Performance of a Two-Level Call Admission Control Scheme for DS-CDMA Wireless Networks

Directory of Open Access Journals (Sweden)

Abraham O. Fapojuwo

2007-11-01

Full Text Available We propose a two-level call admission control (CAC scheme for direct sequence code division multiple access (DS-CDMA wireless networks supporting multimedia traffic and evaluate its performance. The first-level admission control assigns higher priority to real-time calls (also referred to as class 0 calls in gaining access to the system resources. The second level admits nonreal-time calls (or class 1 calls based on the resources remaining after meeting the resource needs for real-time calls. However, to ensure some minimum level of performance for nonreal-time calls, the scheme reserves some resources for such calls. The proposed two-level CAC scheme utilizes the delay-tolerant characteristic of non-real-time calls by incorporating a queue to temporarily store those that cannot be assigned resources at the time of initial access. We analyze and evaluate the call blocking, outage probability, throughput, and average queuing delay performance of the proposed two-level CAC scheme using Markov chain theory. The analytic results are validated by simulation results. The numerical results show that the proposed two-level CAC scheme provides better performance than the single-level CAC scheme. Based on these results, it is concluded that the proposed two-level CAC scheme serves as a good solution for supporting multimedia applications in DS-CDMA wireless communication systems.

Space-time adaptive decision feedback neural receivers with data selection for high-data-rate users in DS-CDMA systems.

Science.gov (United States)

de Lamare, Rodrigo C; Sampaio-Neto, Raimundo

2008-11-01

A space-time adaptive decision feedback (DF) receiver using recurrent neural networks (RNNs) is proposed for joint equalization and interference suppression in direct-sequence code-division multiple-access (DS-CDMA) systems equipped with antenna arrays. The proposed receiver structure employs dynamically driven RNNs in the feedforward section for equalization and multiaccess interference (MAI) suppression and a finite impulse response (FIR) linear filter in the feedback section for performing interference cancellation. A data selective gradient algorithm, based upon the set-membership (SM) design framework, is proposed for the estimation of the coefficients of RNN structures and is applied to the estimation of the parameters of the proposed neural receiver structure. Simulation results show that the proposed techniques achieve significant performance gains over existing schemes.

FIR Filter of DS-CDMA UWB Modem Transmitter

Science.gov (United States)

Kang, Kyu-Min; Cho, Sang-In; Won, Hui-Chul; Choi, Sang-Sung

This letter presents low-complexity digital pulse shaping filter structures of a direct sequence code division multiple access (DS-CDMA) ultra wide-band (UWB) modem transmitter with a ternary spreading code. The proposed finite impulse response (FIR) filter structures using a look-up table (LUT) have the effect of saving the amount of memory by about 50% to 80% in comparison to the conventional FIR filter structures, and consequently are suitable for a high-speed parallel data process.

Pilot power based rate control in CDMA 2000 1x EV-DO Rev-A

Institute of Scientific and Technical Information of China (English)

LIU Xiao-feng; GU Jian; YANG Hong-wen

2008-01-01

This article proposes a new algorithm to improvethe rate control efficiency of enhanced reverse link mediumaccess control (RLMAC) in the code division multiple access(CDMA) lx EV-DO release A(Rev. A) system. The newalgorithm brings reverse access terminal (AT) pilot power tothe RLMAC rate control procedure and makes it easier for alow pilot power user to increase its data rate when the systemis slightly loaded and harder to decrease its date rate when thesystem is heavily loaded. Numerical results of system levelsimulations show that the new algorithm can bring highersystem throughput, lower AT transmission power, and lowersystem load.

Minimum BER Receiver Filters with Block Memory for Uplink DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Debbah Mérouane

2008-01-01

Full Text Available Abstract The problem of synchronous multiuser receiver design in the case of direct-sequence single-antenna code division multiple access (DS-CDMA uplink networks is studied over frequency selective fading channels. An exact expression for the bit error rate (BER is derived in the case of BPSK signaling. Moreover, an algorithm is proposed for finding the finite impulse response (FIR receiver filters with block memory such that the exact BER of the active users is minimized. Several properties of the minimum BER FIR filters with block memory are identified. The algorithm performance is found for scenarios with different channel qualities, spreading code lengths, receiver block memory size, near-far effects, and channel mismatch. For the BPSK constellation, the proposed FIR receiver structure with block memory has significant better BER with respect to and near-far resistance than the corresponding minimum mean square error (MMSE filters with block memory.

2-Step Maximum Likelihood Channel Estimation for Multicode DS-CDMA with Frequency-Domain Equalization

Science.gov (United States)

Kojima, Yohei; Takeda, Kazuaki; Adachi, Fumiyuki

Frequency-domain equalization (FDE) based on the minimum mean square error (MMSE) criterion can provide better downlink bit error rate (BER) performance of direct sequence code division multiple access (DS-CDMA) than the conventional rake combining in a frequency-selective fading channel. FDE requires accurate channel estimation. In this paper, we propose a new 2-step maximum likelihood channel estimation (MLCE) for DS-CDMA with FDE in a very slow frequency-selective fading environment. The 1st step uses the conventional pilot-assisted MMSE-CE and the 2nd step carries out the MLCE using decision feedback from the 1st step. The BER performance improvement achieved by 2-step MLCE over pilot assisted MMSE-CE is confirmed by computer simulation.

Low Complexity Iterative Joint Channel Estimation and Multiuser Detection for DS-CDMA

DEFF Research Database (Denmark)

Christensen, Søren Skovgård; Kocian, Alexander; Fleury, Bernard Henri

2004-01-01

Previously the SAGE algorithm was applied to sub-optimal yet efficient Joint data Detection and channel Estimation (JDE) for DS-CDMA of moderate time complexity. Modifying the expectation and maximization steps of the SAGE-JDE scheme, it is possible to obtain an efficient receiver architecture...

Computationally Efficient Chaotic Spreading Sequence Selection for Asynchronous DS-CDMA

Directory of Open Access Journals (Sweden)

Litviņenko Anna

2017-12-01

Full Text Available The choice of the spreading sequence for asynchronous direct-sequence code-division multiple-access (DS-CDMA systems plays a crucial role for the mitigation of multiple-access interference. Considering the rich dynamics of chaotic sequences, their use for spreading allows overcoming the limitations of the classical spreading sequences. However, to ensure low cross-correlation between the sequences, careful selection must be performed. This paper presents a novel exhaustive search algorithm, which allows finding sets of chaotic spreading sequences of required length with a particularly low mutual cross-correlation. The efficiency of the search is verified by simulations, which show a significant advantage compared to non-selected chaotic sequences. Moreover, the impact of sequence length on the efficiency of the selection is studied.

RLS Channel Estimation with Adaptive Forgetting Factor for DS-CDMA Frequency-Domain Equalization

Science.gov (United States)

Kojima, Yohei; Tomeba, Hiromichi; Takeda, Kazuaki; Adachi, Fumiyuki

Frequency-domain equalization (FDE) based on the minimum mean square error (MMSE) criterion can increase the downlink bit error rate (BER) performance of DS-CDMA beyond that possible with conventional rake combining in a frequency-selective fading channel. FDE requires accurate channel estimation. Recently, we proposed a pilot-assisted channel estimation (CE) based on the MMSE criterion. Using MMSE-CE, the channel estimation accuracy is almost insensitive to the pilot chip sequence, and a good BER performance is achieved. In this paper, we propose a channel estimation scheme using one-tap recursive least square (RLS) algorithm, where the forgetting factor is adapted to the changing channel condition by the least mean square (LMS)algorithm, for DS-CDMA with FDE. We evaluate the BER performance using RLS-CE with adaptive forgetting factor in a frequency-selective fast Rayleigh fading channel by computer simulation.

Secure DS-CDMA spreading codes using fully digital multidimensional multiscroll chaos

KAUST Repository

Mansingka, Abhinav S.

2014-06-18

This paper introduces a generalized fully digital hardware implementation of 1-D, 2-D and 3-D multiscroll chaos through sawtooth nonlinearities in a 3rd order ODE with the Euler approximation, wherein low-significance bits pass all NIST SP. 800-22 tests. The low-significance bits show good performance as spreading code for multiple-access DS-CDMA in AWGN and multipath environments, equivalent to Gold codes. This system capitalizes on complex nonlinear dynamics afforded by multiscroll chaos to provide higher security than conventional codes with the same BER performance demonstrated experimentally on a Xilinx Virtex 4 FPGA with logic utilization less than 1.25% and throughput up to 10.92 Gbits/s.

Fresh Prime Codes Evaluation for Synchronous PPM and OPPM Signaling for Optical CDMA Networks

Science.gov (United States)

Karbassian, M. Massoud; Ghafouri-Shiraz, H.

2007-06-01

In this paper, we have proposed a novel prime spreading sequence family hereby referred to as “Double-Padded Modified Prime Code (DPMPC)” for direct-detection synchronous optical code-division multiple-access (OCDMA) networks. The new code is applied to both pulse-position and overlapping pulse-position modulation CDMA networks, and their performances were evaluated and compared with existing prime codes family. In addition, we have analyzed the system throughput and also introduced a new interference cancellation technique which significantly improves the bit error probability of OCDMA networks.

Minimum BER Receiver Filters with Block Memory for Uplink DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Mérouane Debbah

2008-05-01

Full Text Available The problem of synchronous multiuser receiver design in the case of direct-sequence single-antenna code division multiple access (DS-CDMA uplink networks is studied over frequency selective fading channels. An exact expression for the bit error rate (BER is derived in the case of BPSK signaling. Moreover, an algorithm is proposed for finding the finite impulse response (FIR receiver filters with block memory such that the exact BER of the active users is minimized. Several properties of the minimum BER FIR filters with block memory are identified. The algorithm performance is found for scenarios with different channel qualities, spreading code lengths, receiver block memory size, near-far effects, and channel mismatch. For the BPSK constellation, the proposed FIR receiver structure with block memory has significant better BER with respect to Eb/N0 and near-far resistance than the corresponding minimum mean square error (MMSE filters with block memory.

Two-Stage Maximum Likelihood Estimation (TSMLE for MT-CDMA Signals in the Indoor Environment

Directory of Open Access Journals (Sweden)

Sesay Abu B

2004-01-01

Full Text Available This paper proposes a two-stage maximum likelihood estimation (TSMLE technique suited for multitone code division multiple access (MT-CDMA system. Here, an analytical framework is presented in the indoor environment for determining the average bit error rate (BER of the system, over Rayleigh and Ricean fading channels. The analytical model is derived for quadrature phase shift keying (QPSK modulation technique by taking into account the number of tones, signal bandwidth (BW, bit rate, and transmission power. Numerical results are presented to validate the analysis, and to justify the approximations made therein. Moreover, these results are shown to agree completely with those obtained by simulation.

Multirate IP traffic transmission in flexible access networks based on optical FFH-CDMA

DEFF Research Database (Denmark)

Raddo, Thiago R.; Sanches, Anderson L.; Tafur Monroy, Idelfonso

2016-01-01

In this paper, we propose a new IP transmission architecture over optical fast frequency hopping code-division multiple-access (OFFH-CDMA) network capable of supporting multirate transmissions for applications in flexible optical access networks. The proposed network architecture is independent...

ANALISIS PERILAKU KONSUMEN DALAM MEMILIH JASA LAYANAN OPERATOR MOBILE PHONE YANG BERBASIS CDMA DAN GSM

Directory of Open Access Journals (Sweden)

Demitri Marvin Kadhaffi

2012-05-01

Full Text Available ABSTRAKS Tujuan penelitian ini adalah (1 menganalisis faktor-faktor yang dipertimbangkan konsumen dalam memilih suatu jasa layanan operator mobile phone (baik CDMA maupun GSM, (2 menganalsis variabel dominan yang mempengaruhi perilaku konsumen dalam memilih jasa layanan operator Jenis penelitian ini adalah applied research dengan metode penelitian studi kausal. Penelitian ini ditujukan pada segmen pelajar dan mahasiswa di Kota Malang yang termasuk kelompok Net Generations (yang lahir antara tahun 1977-1997 dengan batas minimal umur untuk responden adalah 17 tahun.  Kerangka Sampel untuk penelitian ini adalah pengguna kartu CDMA dan GSM sebanyak 175 responden. Tehnik Sampling yang digunakan adalah desain sampel non probability dengan metode purposive sample yang kedua yaitu quota sampling. Metode analisa data yang digunakan adalah analisa faktor dan analisa diskriminan Hasil analisa faktor terhadap 34 variabel diperoleh  7 faktor baru, yang diberi label sebagai berikut : (1 faktor citra produk (2 faktor pelayanan, (3 faktor pengaruh lingkungan, (4 faktor promosi,(5 faktor individual, (6 faktor harga, dan (7 faktor proses. Dari analisa diskriminan diperoleh hasil yang bertentangan dengan hipotesis yaitu ternyata variabel harga bukan merupakan variabel yang dominan dalam membedakan perilaku pelanggan operator CDMA dengan GSM. Mereka lebih sensitif terhadap proses produk. Hal ini mengarahkan pelanggan untuk kalangan pelajar dan mahasiswa sebagai kelompok smart. Hasil penelitian menyimpulkan bahwa untuk membangun keunggulan bersaing operator harus meraih keunggulan posisional melalui diferensiasi “content” jasa yang dihasilkan yaitu berupa proses, sebagai hasil dari aplikasi  positioning produk.   Kata kunci: perilaku konsumen, jasa layanan, mobile phone   ABSTRACT Objective of this research are (1 to identify factors that customer consider in choosing mobile phone operator service (whether CDMA and GSM, (2 to identify dominant variable that

Free-space optical code-division multiple-access system design

Science.gov (United States)

Jeromin, Lori L.; Kaufmann, John E.; Bucher, Edward A.

1993-08-01

This paper describes an optical direct-detection multiple access communications system for free-space satellite networks utilizing code-division multiple-access (CDMA) and forward error correction (FEC) coding. System performance is characterized by how many simultaneous users operating at data rate R can be accommodated in a signaling bandwidth W. The performance of two CDMA schemes, optical orthogonal codes (OOC) with FEC and orthogonal convolutional codes (OCC), is calculated and compared to information-theoretic capacity bounds. The calculations include the effects of background and detector noise as well as nonzero transmitter extinction ratio and power imbalance among users. A system design for 10 kbps multiple-access communications between low-earth orbit satellites is given. With near- term receiver technology and representative system losses, a 15 W peak-power transmitter provides 10-6 BER performance with seven interfering users and full moon background in the receiver FOV. The receiver employs an array of discrete wide-area avalanche photodiodes (APD) for wide field of view coverage. Issues of user acquisition and synchronization, implementation technology, and system scalability are also discussed.

Reduced-Rank Chip-Level MMSE Equalization for the 3G CDMA Forward Link with Code-Multiplexed Pilot

Directory of Open Access Journals (Sweden)

Goldstein J Scott

2002-01-01

Full Text Available This paper deals with synchronous direct-sequence code-division multiple access (CDMA transmission using orthogonal channel codes in frequency selective multipath, motivated by the forward link in 3G CDMA systems. The chip-level minimum mean square error (MMSE estimate of the (multiuser synchronous sum signal transmitted by the base, followed by a correlate and sum, has been shown to perform very well in saturated systems compared to a Rake receiver. In this paper, we present the reduced-rank, chip-level MMSE estimation based on the multistage nested Wiener filter (MSNWF. We show that, for the case of a known channel, only a small number of stages of the MSNWF is needed to achieve near full-rank MSE performance over a practical single-to-noise ratio (SNR range. This holds true even for an edge-of-cell scenario, where two base stations are contributing near equal-power signals, as well as for the single base station case. We then utilize the code-multiplexed pilot channel to train the MSNWF coefficients and show that adaptive MSNWF operating in a very low rank subspace performs slightly better than full-rank recursive least square (RLS and significantly better than least mean square (LMS. An important advantage of the MSNWF is that it can be implemented in a lattice structure, which involves significantly less computation than RLS. We also present structured MMSE equalizers that exploit the estimate of the multipath arrival times and the underlying channel structure to project the data vector onto a much lower dimensional subspace. Specifically, due to the sparseness of high-speed CDMA multipath channels, the channel vector lies in the subspace spanned by a small number of columns of the pulse shaping filter convolution matrix. We demonstrate that the performance of these structured low-rank equalizers is much superior to unstructured equalizers in terms of convergence speed and error rates.

Handoff Triggering and Network Selection Algorithms for Load-Balancing Handoff in CDMA-WLAN Integrated Networks

Directory of Open Access Journals (Sweden)

Khalid Qaraqe

2008-10-01

Full Text Available This paper proposes a novel vertical handoff algorithm between WLAN and CDMA networks to enable the integration of these networks. The proposed vertical handoff algorithm assumes a handoff decision process (handoff triggering and network selection. The handoff trigger is decided based on the received signal strength (RSS. To reduce the likelihood of unnecessary false handoffs, the distance criterion is also considered. As a network selection mechanism, based on the wireless channel assignment algorithm, this paper proposes a context-based network selection algorithm and the corresponding communication algorithms between WLAN and CDMA networks. This paper focuses on a handoff triggering criterion which uses both the RSS and distance information, and a network selection method which uses context information such as the dropping probability, blocking probability, GoS (grade of service, and number of handoff attempts. As a decision making criterion, the velocity threshold is determined to optimize the system performance. The optimal velocity threshold is adjusted to assign the available channels to the mobile stations. The optimal velocity threshold is adjusted to assign the available channels to the mobile stations using four handoff strategies. The four handoff strategies are evaluated and compared with each other in terms of GOS. Finally, the proposed scheme is validated by computer simulations.

Handoff Triggering and Network Selection Algorithms for Load-Balancing Handoff in CDMA-WLAN Integrated Networks

Directory of Open Access Journals (Sweden)

Kim Jang-Sub

2008-01-01

Full Text Available This paper proposes a novel vertical handoff algorithm between WLAN and CDMA networks to enable the integration of these networks. The proposed vertical handoff algorithm assumes a handoff decision process (handoff triggering and network selection. The handoff trigger is decided based on the received signal strength (RSS. To reduce the likelihood of unnecessary false handoffs, the distance criterion is also considered. As a network selection mechanism, based on the wireless channel assignment algorithm, this paper proposes a context-based network selection algorithm and the corresponding communication algorithms between WLAN and CDMA networks. This paper focuses on a handoff triggering criterion which uses both the RSS and distance information, and a network selection method which uses context information such as the dropping probability, blocking probability, GoS (grade of service, and number of handoff attempts. As a decision making criterion, the velocity threshold is determined to optimize the system performance. The optimal velocity threshold is adjusted to assign the available channels to the mobile stations. The optimal velocity threshold is adjusted to assign the available channels to the mobile stations using four handoff strategies. The four handoff strategies are evaluated and compared with each other in terms of GOS. Finally, the proposed scheme is validated by computer simulations.

Design and Performance Analysis of an Adaptive Receiver for Multicarrier DS-CDMA

Directory of Open Access Journals (Sweden)

Wang Huahui

2007-01-01

Full Text Available An adaptive parallel interference cancelation (APIC scheme is proposed for the multicarrier direct sequence code division multiple access (MC-DS-CDMA system. Frequency diversity inherent in the MC system is exploited through maximal ratio combining, and an adaptive least mean square algorithm is used to estimate the multiple access interference. Theoretical analysis on the bit-error rate (BER of the APIC receiver is presented. Under a unified signal model, the conventional PIC (CPIC is shown to be a special case of the APIC. Hence the BER derivation for the APIC is also applicable to the CPIC. The performance and the accuracy of the theoretical results are examined via simulations under different design parameters, which show that the APIC outperforms the CPIC receiver provided that the adaptive parameters are properly selected.

Iterative Soft Decision Interference Cancellation for DS-CDMA Employing the Distribution of Interference

Directory of Open Access Journals (Sweden)

Gerstacker WolfgangH

2010-01-01

Full Text Available A well-known receiver strategy for direct-sequence code-division multiple-access (DS-CDMA transmission is iterative soft decision interference cancellation. For calculation of soft estimates used for cancellation, the distribution of residual interference is commonly assumed to be Gaussian. In this paper, we analyze matched filter-based iterative soft decision interference cancellation (MF ISDIC when utilizing an approximation of the actual probability density function (pdf of residual interference. In addition, a hybrid scheme is proposed, which reduces computational complexity by considering the strongest residual interferers according to their pdf while the Gaussian assumption is applied to the weak residual interferers. It turns out that the bit error ratio decreases already noticeably when only a small number of residual interferers is regarded according to their pdf. For the considered DS-CDMA transmission the bit error ratio decreases by 80% for high signal-to-noise ratios when modeling all residual interferers but the strongest three to be Gaussian distributed.

Improving Multi Access Interference Suppression in Optical CDMA by using all-Optical Signal Processing

Directory of Open Access Journals (Sweden)

T. B. Osadola

2013-06-01

Full Text Available This paper presents the study of a novel all-optical method for processing optical CDMA signals towards improving suppression of multi access interference. The main focus is on incoherent OCDMA systems using multiwavelength 2D-WH/TS codes generated using FBG based encoders and decoders. The MAI suppression capabilities based on its ability to eliminate selective wavelength pulse processing have been shown. A novel transmitter architecture that achieves up to 3dB power saving was also presented. As a result of hardware savings, processing cost will be significantly reduced and power budget improvement resulted in improved performance.

Performance Analysis of Polarization Modulated DirectDetection Optical CDMA Systems over Turbulent FSO LinksModeled by the Gamma-Gamma Distribution

Directory of Open Access Journals (Sweden)

Fan Bai

2015-01-01

Full Text Available This paper proposes a theoretical study to characterize the transmission of optical code division multiple access (CDMA systems deploying polarization shift keying (PolSK over a free space optical (FSO link under the impact of atmospheric turbulence. In our analysis, a novel transceiver architecture for atmospheric OCDMA FSO systems based on polarization modulation with direct detection is proposed and discussed. A detailed analytical model for PolSK-OCDMA systems over a turbulent FSO link is provided. Further, we derive a closed-form bit error ratio (BER and outage probability expressions, taking into account the multiple-access interference (MAI, optical noise and the atmospheric turbulence effect on the FSO link modeled by the Gamma-Gamma distribution. Finally, the results of this study show the most significant parameters that degrade the transmission performance of the PolSK-OCDMA signal over FSO links and indicate that the proposed approach offers improved bit error ratio (BER performances compared to the on-off-keying (OOK modulation scheme in the presence of turbulence.

An efficient CDMA decoder for correlated information sources

International Nuclear Information System (INIS)

Efraim, Hadar; Yacov, Nadav; Kanter, Ido; Shental, Ori

2009-01-01

We consider the detection of correlated information sources in the ubiquitous code-division multiple-access (CDMA) scheme. We propose a message-passing based scheme for detecting correlated sources directly, with no need for source coding. The detection is done simultaneously over a block of transmitted binary symbols (word). Simulation results are provided, demonstrating a substantial improvement in bit error rate in comparison with the unmodified detector and the alternative of source compression. The robustness of the error-performance improvement is shown under practical model settings, including wrong estimation of the generating Markov transition matrix and finite-length spreading codes

Neurological abnormalities associated with CDMA exposure.

Science.gov (United States)

Hocking, B; Westerman, R

2001-09-01

Dysaesthesiae of the scalp and neurological abnormality after mobile phone use have been reported previously, but the roles of the phone per se or the radiations in causing these findings have been questioned. We report finding a neurological abnormality in a patient after accidental exposure of the left side of the face to mobile phone radiation [code division multiple access (CDMA)] from a down-powered mobile phone base station antenna. He had headaches, unilateral left blurred vision and pupil constriction, unilateral altered sensation on the forehead, and abnormalities of current perception thresholds on testing the left trigeminal ophthalmic nerve. His nerve function recovered during 6 months follow-up. His exposure was 0.015-0.06 mW/cm(2) over 1-2 h. The implications regarding health effects of radiofrequency radiation are discussed.

DESIGN AND IMPLEMENTATION OF IMPROVED SUPERIMPOSED CYCLIC OPTICAL ORTHOGONAL CODES (SCOOC BASED OPTICAL ENCODER/DECODER STRUCTURE FOR 1GBPS OPTICAL CDMA SYSTEM

Directory of Open Access Journals (Sweden)

GURJIT KAUR

2010-12-01

Full Text Available In this paper, an improved form of two dimensional optical orthogonal codes is introduced for optical CDMA system by using just six lasers. This new technique not only reduces the length of the code but also improves the bit error rate (BER performance of the system. The uniqueness of this coding architecture is that the two adjacent codes are not only different by their time slots but have different wavelength combination as well. The encoder and decoder structure has been designed with the help of filters and optical delay lines. An OCDMA system at 1 Gbps bit rate is designed for above codes and performance is evaluated and compared for various parameters i.e. number of simultaneous users, bit error rate, quality factor. The OCDMA system can accommodate 25 users for permissible BER of 10-9, with -15db received power at 1 Gbps bit rate respectively. If received power is kept low i.e. -22db, the OCDMA system can support 16 users with extremely low BER of 1.58e-41 for 1G bps bit rate.

Accurate Bit Error Rate Calculation for Asynchronous Chaos-Based DS-CDMA over Multipath Channel

Science.gov (United States)

Kaddoum, Georges; Roviras, Daniel; Chargé, Pascal; Fournier-Prunaret, Daniele

2009-12-01

An accurate approach to compute the bit error rate expression for multiuser chaosbased DS-CDMA system is presented in this paper. For more realistic communication system a slow fading multipath channel is considered. A simple RAKE receiver structure is considered. Based on the bit energy distribution, this approach compared to others computation methods existing in literature gives accurate results with low computation charge. Perfect estimation of the channel coefficients with the associated delays and chaos synchronization is assumed. The bit error rate is derived in terms of the bit energy distribution, the number of paths, the noise variance, and the number of users. Results are illustrated by theoretical calculations and numerical simulations which point out the accuracy of our approach.

Performance Analysis of New Binary User Codes for DS-CDMA Communication

Science.gov (United States)

Usha, Kamle; Jaya Sankar, Kottareddygari

2016-03-01

This paper analyzes new binary spreading codes through correlation properties and also presents their performance over additive white Gaussian noise (AWGN) channel. The proposed codes are constructed using gray and inverse gray codes. In this paper, a n-bit gray code appended by its n-bit inverse gray code to construct the 2n-length binary user codes are discussed. Like Walsh codes, these binary user codes are available in sizes of power of two and additionally code sets of length 6 and their even multiples are also available. The simple construction technique and generation of code sets of different sizes are the salient features of the proposed codes. Walsh codes and gold codes are considered for comparison in this paper as these are popularly used for synchronous and asynchronous multi user communications respectively. In the current work the auto and cross correlation properties of the proposed codes are compared with those of Walsh codes and gold codes. Performance of the proposed binary user codes for both synchronous and asynchronous direct sequence CDMA communication over AWGN channel is also discussed in this paper. The proposed binary user codes are found to be suitable for both synchronous and asynchronous DS-CDMA communication.

A Low-Complexity Joint Synchronization and Detection Algorithm for Single-Band DS-CDMA UWB Communications

DEFF Research Database (Denmark)

Christensen, Lars P.B.

2005-01-01

The problem of asynchronous direct-sequence code division multiple access (DS-CDMA) detection over the ultra-wideband (UWB) multipath channel is considered. A joint synchronization, channel-estimation and multi-user detection scheme based on the adaptive linear minimum mean-square error (LMMSE...

Space-Time Chip Equalization for Maximum Diversity Space-Time Block Coded DS-CDMA Downlink Transmission

NARCIS (Netherlands)

Leus, G.; Petré, F.; Moonen, M.

2004-01-01

In the downlink of DS-CDMA, frequency-selectivity destroys the orthogonality of the user signals and introduces multiuser interference (MUI). Space-time chip equalization is an efficient tool to restore the orthogonality of the user signals and suppress the MUI. Furthermore, multiple-input

Performance analysis of a handoff scheme for two-tier cellular CDMA networks

Directory of Open Access Journals (Sweden)

Ahmed Hamad

2011-07-01

Full Text Available A two-tier model is used in cellular networks to improve the Quality of Service (QoS, namely to reduce the blocking probability of new calls and the forced termination probability of ongoing calls. One tier, the microcells, is used for slow or stationary users, and the other, the macrocell, is used for high speed users. In Code-Division Multiple-Access (CDMA cellular systems, soft handoffs are supported, which provides ways for further QoS improvement. In this paper, we introduce such a way; namely, a channel borrowing scheme used in conjunction with a First-In-First-Out (FIFO queue in the macrocell tier. A multidimensional Markov chain to model the resulting system is established, and an iterative technique to find the steady-state probability distribution is utilized. This distribution is then used to find the performance measures of interest: new call blocking probability, and forced termination probability.

Joint power control based on service factor for code division multiple access system%TDD-CDMA系统中基于业务统计的联合功率控制算法

Institute of Scientific and Technical Information of China (English)

陈波; 戎蒙恬; 胡威

2008-01-01

An important feature of the traffic in mobile networks is burstiness. Drawbacks of conventional power control algorithms for time division duplex (TDD)-code division multiple access (CDMA) systems are analyzed. A joint power control algorithm based on service factor is presented to address the TDD-CDMA mobile services in the burst mode according to the Markov modulated Bernoulli process. The joint power control equation is derived. A function model is developed to verify the new algorithm and evaluate its performance. Simulation results show that the new power control algorithm can estimate interference strength more precisely, speed up convergence of power control, and enhance power efficiency and system capacity. It is shown that the proposed algorithm is more robust against rink gain changes, and outperforms the reference algorithms.

Single integrated device for optical CDMA code processing in dual-code environment.

Science.gov (United States)

Huang, Yue-Kai; Glesk, Ivan; Greiner, Christoph M; Iazkov, Dmitri; Mossberg, Thomas W; Wang, Ting; Prucnal, Paul R

2007-06-11

We report on the design, fabrication and performance of a matching integrated optical CDMA encoder-decoder pair based on holographic Bragg reflector technology. Simultaneous encoding/decoding operation of two multiple wavelength-hopping time-spreading codes was successfully demonstrated and shown to support two error-free OCDMA links at OC-24. A double-pass scheme was employed in the devices to enable the use of longer code length.

Performance Analysis of a New Coded TH-CDMA Scheme in Dispersive Infrared Channel with Additive Gaussian Noise

Science.gov (United States)

Hamdi, Mazda; Kenari, Masoumeh Nasiri

2013-06-01

We consider a time-hopping based multiple access scheme introduced in [1] for communication over dispersive infrared links, and evaluate its performance for correlator and matched filter receivers. In the investigated time-hopping code division multiple access (TH-CDMA) method, the transmitter benefits a low rate convolutional encoder. In this method, the bit interval is divided into Nc chips and the output of the encoder along with a PN sequence assigned to the user determines the position of the chip in which the optical pulse is transmitted. We evaluate the multiple access performance of the system for correlation receiver considering background noise which is modeled as White Gaussian noise due to its large intensity. For the correlation receiver, the results show that for a fixed processing gain, at high transmit power, where the multiple access interference has the dominant effect, the performance improves by the coding gain. But at low transmit power, in which the increase of coding gain leads to the decrease of the chip time, and consequently, to more corruption due to the channel dispersion, there exists an optimum value for the coding gain. However, for the matched filter, the performance always improves by the coding gain. The results show that the matched filter receiver outperforms the correlation receiver in the considered cases. Our results show that, for the same bandwidth and bit rate, the proposed system excels other multiple access techniques, like conventional CDMA and time hopping scheme.

Automatic Loss Adjustment for CDMA2000 and 1xEV-DO Standard for Downlink and Uplink

Directory of Open Access Journals (Sweden)

Jiri Kominek

2014-01-01

Full Text Available The functional and thermal testing of the mobile phone is always performed under various conditions that vary in terms of the connection between the DUT (Device Under Test and the measuring instrument. To achieve repeatable measurements under such conditions, it is necessary to adjust uplink and downlink loss using the instrument's external attenuation. While for GSM, WCDMA and LTE this is a relatively easy task, CDMA2000 and 1xEV-DO make automation of the adjustment process somewhat challenging due to the nature of the CDMA standard. An especially forward link is more complicated as those tests are run in signaling mode and not all instruments provide an FER value measured by an MS. This paper describes the algorithm for forward link loss adjustment and its implementation using Rohde & Schwarz CMW500.

Approximate equiangular tight frames for compressed sensing and CDMA applications

Science.gov (United States)

Tsiligianni, Evaggelia; Kondi, Lisimachos P.; Katsaggelos, Aggelos K.

2017-12-01

Performance guarantees for recovery algorithms employed in sparse representations, and compressed sensing highlights the importance of incoherence. Optimal bounds of incoherence are attained by equiangular unit norm tight frames (ETFs). Although ETFs are important in many applications, they do not exist for all dimensions, while their construction has been proven extremely difficult. In this paper, we construct frames that are close to ETFs. According to results from frame and graph theory, the existence of an ETF depends on the existence of its signature matrix, that is, a symmetric matrix with certain structure and spectrum consisting of two distinct eigenvalues. We view the construction of a signature matrix as an inverse eigenvalue problem and propose a method that produces frames of any dimensions that are close to ETFs. Due to the achieved equiangularity property, the so obtained frames can be employed as spreading sequences in synchronous code-division multiple access (s-CDMA) systems, besides compressed sensing.

Power-Controlled CDMA Cell Sectorization with Multiuser Detection: A Comprehensive Analysis on Uplink and Downlink

Directory of Open Access Journals (Sweden)

Aylin Yener

2007-12-01

Full Text Available We consider the joint optimization problem of cell sectorization, transmit power control and multiuser detection for a CDMA cell. Given the number of sectors and user locations, the cell is appropriately sectorized such that the total transmit power, as well as the receiver filters, is optimized. We formulate the corresponding joint optimization problems for both the uplink and the downlink and observe that in general, the resulting optimum transmit and receive beamwidth values for the directional antennas at the base station are different. We present the optimum solution under a general setting with arbitrary signature sets, multipath channels, realistic directional antenna responses and identify its complexity. We propose a low-complexity sectorization algorithm that performs near optimum and compare its performance with that of optimum solution. The results suggest that by intelligently combining adaptive cell sectorization, power control, and linear multiuser detection, we are able to increase the user capacity of the cell. Numerical results also indicate robustness of optimum sectorization against Gaussian channel estimation error.

Power-Controlled CDMA Cell Sectorization with Multiuser Detection: A Comprehensive Analysis on Uplink and Downlink

Directory of Open Access Journals (Sweden)

Oh Changyoon

2007-01-01

Full Text Available We consider the joint optimization problem of cell sectorization, transmit power control and multiuser detection for a CDMA cell. Given the number of sectors and user locations, the cell is appropriately sectorized such that the total transmit power, as well as the receiver filters, is optimized. We formulate the corresponding joint optimization problems for both the uplink and the downlink and observe that in general, the resulting optimum transmit and receive beamwidth values for the directional antennas at the base station are different. We present the optimum solution under a general setting with arbitrary signature sets, multipath channels, realistic directional antenna responses and identify its complexity. We propose a low-complexity sectorization algorithm that performs near optimum and compare its performance with that of optimum solution. The results suggest that by intelligently combining adaptive cell sectorization, power control, and linear multiuser detection, we are able to increase the user capacity of the cell. Numerical results also indicate robustness of optimum sectorization against Gaussian channel estimation error.

DEPLOYMENT OF ANTENNA ARRAY FOR DATA RETRIEVAL IN CDMA ENVIROMENT

OpenAIRE

RICARDO ZELENOVSKY

2001-01-01

Este trabalho de tese trata do emprego de arranjos de antenas em ambientes de comunicação móvel,dando-se ênfase ao canal de dados reverso do Sistema IS-95. Propõe-se dois estimadores: um para a direção de chegada dos sinais e outro para outros dados. Inicialmente é apresentado um estudo sobre arranjos de antenas e dos principais detalhes do sistema IS-95,especialmente a multiplicidade de acesso via divisão por códigos (CDMA).Aborda-se em seguida o problema d...

Joint Frequency-Domain Equalization and Despreading for Multi-Code DS-CDMA Using Cyclic Delay Transmit Diversity

Science.gov (United States)

Yamamoto, Tetsuya; Takeda, Kazuki; Adachi, Fumiyuki

Frequency-domain equalization (FDE) based on the minimum mean square error (MMSE) criterion can provide a better bit error rate (BER) performance than rake combining. To further improve the BER performance, cyclic delay transmit diversity (CDTD) can be used. CDTD simultaneously transmits the same signal from different antennas after adding different cyclic delays to increase the number of equivalent propagation paths. Although a joint use of CDTD and MMSE-FDE for direct sequence code division multiple access (DS-CDMA) achieves larger frequency diversity gain, the BER performance improvement is limited by the residual inter-chip interference (ICI) after FDE. In this paper, we propose joint FDE and despreading for DS-CDMA using CDTD. Equalization and despreading are simultaneously performed in the frequency-domain to suppress the residual ICI after FDE. A theoretical conditional BER analysis is presented for the given channel condition. The BER analysis is confirmed by computer simulation.

Spectral Subtraction Approach for Interference Reduction of MIMO Channel Wireless Systems

Directory of Open Access Journals (Sweden)

Tomohiro Ono

2005-08-01

Full Text Available In this paper, a generalized spectral subtraction approach for reducing additive impulsive noise, narrowband signals, white Gaussian noise and DS-CDMA interferences in MIMO channel DS-CDMA wireless communication systems is investigated. The interference noise reduction or suppression is essential problem in wireless mobile communication systems to improve the quality of communication. The spectrum subtraction scheme is applied to the interference noise reduction problems for noisy MIMO channel systems. The interferences in space and time domain signals can effectively be suppressed by selecting threshold values, and the computational load with the FFT is not large. Further, the fading effects of channel are compensated by spectral modification with the spectral subtraction process. In the simulations, the effectiveness of the proposed methods for the MIMO channel DS-CDMA is shown to compare with the conventional MIMO channel DS-CDMA.

Successive Interference Cancellation for DS-Optical PPM-CDMA Systems

Science.gov (United States)

Alsowaidi, N.; Eltaif, Tawfig; Mokhtar, M. R.

2016-06-01

In this paper we introduce a successive interference cancellation (SIC) scheme for direct sequence optical code division multiple access (DS-OCDMA) systems using pulse position modulation (PPM). Considering double-padded modified prime code (DPMPC) as a signature sequence code, results show that the system has better performance in terms of both capacity and bit error rate (BER) as compared to the one without cancellation scheme, where the system with SIC scheme can support up to 88 users while the system without SIC scheme can support only 38 users at similar BER=10-9. Although the receiver sensitivity is affected by the overlapping between users, which limits the system performance, the theoretical analysis of this issue indicates the influence of the size of M-ary PPM on OCDMA system. Hence, the BER value is still sufficient for good system performance.

A MUSIC-Based Algorithm for Blind User Identification in Multiuser DS-CDMA

Directory of Open Access Journals (Sweden)

M. Reza Soleymani

2005-04-01

Full Text Available A blind scheme based on multiple-signal classification (MUSIC algorithm for user identification in a synchronous multiuser code-division multiple-access (CDMA system is suggested. The scheme is blind in the sense that it does not require prior knowledge of the spreading codes. Spreading codes and users' power are acquired by the scheme. Eigenvalue decomposition (EVD is performed on the received signal, and then all the valid possible signature sequences are projected onto the subspaces. However, as a result of this process, some false solutions are also produced and the ambiguity seems unresolvable. Our approach is to apply a transformation derived from the results of the subspace decomposition on the received signal and then to inspect their statistics. It is shown that the second-order statistics of the transformed signal provides a reliable means for removing the false solutions.

Simulations of floor cooling system capacity

International Nuclear Information System (INIS)

Odyjas, Andrzej; Górka, Andrzej

2013-01-01

Floor cooling system capacity depends on its physical and operative parameters. Using numerical simulations, it appears that cooling capacity of the system largely depends on the type of cooling loads occurring in the room. In the case of convective cooling loads capacity of the system is small. However, when radiation flux falls directly on the floor the system significantly increases productivity. The article describes the results of numerical simulations which allow to determine system capacity in steady thermal conditions, depending on the type of physical parameters of the system and the type of cooling load occurring in the room. Moreover, the paper sets out the limits of system capacity while maintaining a minimum temperature of the floor surface equal to 20 °C. The results are helpful for designing system capacity in different type of cooling loads and show maximum system capacity in acceptable thermal comfort condition. -- Highlights: ► We have developed numerical model for simulation of floor cooling system. ► We have described floor system capacity depending on its physical parameters. ► We have described floor system capacity depending on type of cooling loads. ► The most important in the obtained cooling capacities is the type of cooling loads. ► The paper sets out the possible maximum cooling floor system capacity

BAMUD Features Demonstration by System View

Directory of Open Access Journals (Sweden)

D. Kocur

2004-09-01

Full Text Available Direct-sequence code-division multiple access (DS-CDMA is afrequently used wireless technology in DS-CDMA communications. Theconventional DS-CDMA detector follows a single-user detection strategyin which each user is detected separately without regard for the otherusers. The better strategy is multi-user detection (MUD, whereinformation about multiple users is used to improve detection of eachindividual user. This paper presents an adaptive multi-user detectorconverging (for any initialization to the minimum mean square error(MMSE detector without requiring training sequences. This blindmulti-user detector (BAMUD requires no more knowledge than does theconventional single-user detector. The structure of adaptive blinddetector is simulated by the system design tool SystemView. The aimfocus is to verify theoretical knowledge of BAMUD structure usinghardware-oriented PC-based model in SystemView.

Design and simulations of a spectral efficient optical code division multiple access scheme using alternated energy differentiation and single-user soft-decision demodulation

Science.gov (United States)

A. Garba, Aminata

2017-01-01

This paper presents a new approach to optical Code Division Multiple Access (CDMA) network transmission scheme using alternated amplitude sequences and energy differentiation at the transmitters to allow concurrent and secure transmission of several signals. The proposed system uses error control encoding and soft-decision demodulation to reduce the multi-user interference at the receivers. The design of the proposed alternated amplitude sequences, the OCDMA energy modulators and the soft decision, single-user demodulators are also presented. Simulation results show that the proposed scheme allows achieving spectral efficiencies higher than several reported results for optical CDMA and much higher than the Gaussian CDMA capacity limit.

Multicarrier Spread Spectrum Modulation Schemes and Efficient FFT Algorithms for Cognitive Radio Systems

Directory of Open Access Journals (Sweden)

Mohandass Sundararajan

2014-07-01

Full Text Available Spread spectrum (SS and multicarrier modulation (MCM techniques are recognized as potential candidates for the design of underlay and interweave cognitive radio (CR systems, respectively. Direct Sequence Code Division Multiple Access (DS-CDMA is a spread spectrum technique generally used in underlay CR systems. Orthogonal Frequency Division Multiplexing (OFDM is the basic MCM technique, primarily used in interweave CR systems. There are other MCM schemes derived from OFDM technique, like Non-Contiguous OFDM, Spread OFDM, and OFDM-OQAM, which are more suitable for CR systems. Multicarrier Spread Spectrum Modulation (MCSSM schemes like MC-CDMA, MC-DS-CDMA and SS-MC-CDMA, combine DS-CDMA and OFDM techniques in order to improve the CR system performance and adaptability. This article gives a detailed survey of the various spread spectrum and multicarrier modulation schemes proposed in the literature. Fast Fourier Transform (FFT plays a vital role in all the multicarrier modulation techniques. The FFT part of the modem can be used for spectrum sensing. The performance of the FFT operator plays a crucial role in the overall performance of the system. Since the cognitive radio is an adaptive system, the FFT operator must also be adaptive for various input/output values, in order to save energy and time taken for execution. This article also includes the various efficient FFT algorithms proposed in the literature, which are suitable for CR systems.

Verhulst populational model applied to distributed power control in DS/CDMA

Directory of Open Access Journals (Sweden)

Paul Jean Etienne Jeszensky

2005-02-01

Full Text Available In this paper the continuous dynamic model of Verhulst is used. It had been initially elaborated to describe the population growth of biological species with food restriction and physical space, in order to synthesize a new distributed power control algorithm (DPCA, applicable in direct sequence code division multiple access (DS-CDMA systems. The discretization of the corresponding differential equation is accomplished via numeric integration Euler method (NIE. The properties of the proposed recursive algorithm, as Euclidian distance from optimum vector after convergence, convergence speed, normalized mean squared error (NSE, average power consumption per user and implementation complexity, are investigated through simulations. The simulation results are confronted with the other DPCAs: the classic algorithm derived by Foschini and Miljanic and the sigmoidal by Uykan and Koivo. With estimate errors, the proposed DPCA showed smaller discrepancy from the optimum power vector allocation after convergence and better convergence. Additionally, the Gerchgorin Circles theory (GC is applied for the feasibility of the power allocation problem.

A Review on Successive Interference Cancellation-Based Optical PPM-CDMA Signaling

Science.gov (United States)

Alsowaidi, Naif; Eltaif, Tawfig; Mokhtar, Mohd Ridzuan

2017-06-01

This paper presents a comprehensive review of successive interference cancellation (SIC) scheme using pulse position modulation (PPM) for optical code division multiple access (OCDMA) systems. SIC scheme focuses on high-intensity signal, which will be selected after all users were detected, and then it will be subtracted from the overall received signal, hence, generating a new received signal. This process continues till all users eliminated one by one have been detected. It is shown that the random location of the sequences due to PPM encoding can reduce the probability of concentrated buildup of the pulse overlap in any one-slot time, and support SIC to easily remove the effect of the strongest signal at each stage of the cancellation process. The system bit error rate (BER) performance with modified quadratic congruence (MQC) codes used as signature sequence has been investigated. A detailed theoretical analysis of proposed system taking into account the impact of imperfect interference cancellation, the loss produced from the splitting during encoding and decoding, the channel loss and multiple access interference is presented. Results show that under average effective power constraint optical CDMA system using SIC scheme with M-ary PPM modulation outperforms conventional correlator detector and SIC scheme with on-off keying (OOK) modulation.

High spectral efficiency optical CDMA system based on guard-time and optical hard-limiting (OHL)

Energy Technology Data Exchange (ETDEWEB)

Gagliardi, R M; Bennett, C V; Mendez, A J; Hernandez, V J; Lennon, W J

2003-12-02

Optical code-division multiple access (OCDMA) is an interesting subject of research because of its potential to support asynchronous, bursty communications. OCDMA has been investigated for local area networks, access networks, and, more recently, as a packet label for emerging networks. Two-dimensional (2-D) OCDMA codes are preferred in current research because of the flexibility of designing the codes and their higher cardinality and spectral efficiency (SE) compared with direct sequence codes based on on-off keying and intensity modulation/direct detection, and because they lend themselves to being implemented with devices developed for wavelength-division-multiplexed (WDM) transmission (the 2-D codes typically combine wavelength and time as the two dimensions of the codes). This paper shows rigorously that 2-D wavelength/time codes have better SE than one-dimensional (1-D) CDMA/WDM combinations (of the same cardinality). Then, the paper describes a specific set of wavelength/time (W/T) codes and their implementation. These 2-D codes are high performance because they simultaneously have high cardinality (/spl Gt/10), per-user high bandwidth (>1 Gb/s), and high SE (>0.10 b/s/Hz). The physical implementation of these W/T codes is described and their performance evaluated by system simulations and measurements on an OCDMA technology demonstrator. This research shows that OCDMA implementation complexity (e.g., incorporating double hard-limiting and interference estimation) can be avoided by using a guard time in the codes and an optical hard limiter in the receiver.

Redes celulares de tercera generación: CDMA2000 Y WCDMA

OpenAIRE

Jaime Sánchez García; Myriam Meza Múgica

2005-01-01

Este artículo ofrece un panorama general de los sistemas de comunicaciones móviles celulares de tercera generación (3G) que han tenido una mayor aceptación (CDMA2000 y WCDMA) en el mercado, y una comparación basada en los puntos principales donde los sistemas difieren que indica las ventajas y desventajas de cada uno. Los sistemas de comunicaciones móviles celulares 3G ofrecen mayores capacidades de transmisión a los de segunda generación (2G), y permiten brindar, además de los tr...

Performance Analysis of a De-correlated Modified Code Tracking Loop for Synchronous DS-CDMA System under Multiuser Environment

Science.gov (United States)

Wu, Ya-Ting; Wong, Wai-Ki; Leung, Shu-Hung; Zhu, Yue-Sheng

This paper presents the performance analysis of a De-correlated Modified Code Tracking Loop (D-MCTL) for synchronous direct-sequence code-division multiple-access (DS-CDMA) systems under multiuser environment. Previous studies have shown that the imbalance of multiple access interference (MAI) in the time lead and time lag portions of the signal causes tracking bias or instability problem in the traditional correlating tracking loop like delay lock loop (DLL) or modified code tracking loop (MCTL). In this paper, we exploit the de-correlating technique to combat the MAI at the on-time code position of the MCTL. Unlike applying the same technique to DLL which requires an extensive search algorithm to compensate the noise imbalance which may introduce small tracking bias under low signal-to-noise ratio (SNR), the proposed D-MCTL has much lower computational complexity and exhibits zero tracking bias for the whole range of SNR, regardless of the number of interfering users. Furthermore, performance analysis and simulations based on Gold codes show that the proposed scheme has better mean square tracking error, mean-time-to-lose-lock and near-far resistance than the other tracking schemes, including traditional DLL (T-DLL), traditional MCTL (T-MCTL) and modified de-correlated DLL (MD-DLL).

An information theory criteria based blind method for enumerating active users in DS-CDMA system

Science.gov (United States)

Samsami Khodadad, Farid; Abed Hodtani, Ghosheh

2014-11-01

In this paper, a new and blind algorithm for active user enumeration in asynchronous direct sequence code division multiple access (DS-CDMA) in multipath channel scenario is proposed. The proposed method is based on information theory criteria. There are two main categories of information criteria which are widely used in active user enumeration, Akaike Information Criterion (AIC) and Minimum Description Length (MDL) information theory criteria. The main difference between these two criteria is their penalty functions. Due to this difference, MDL is a consistent enumerator which has better performance in higher signal-to-noise ratios (SNR) but AIC is preferred in lower SNRs. In sequel, we propose a SNR compliance method based on subspace and training genetic algorithm to have the performance of both of them. Moreover, our method uses only a single antenna, in difference to the previous methods which decrease hardware complexity. Simulation results show that the proposed method is capable of estimating the number of active users without any prior knowledge and the efficiency of the method.

Subband Adaptive Array for DS-CDMA Mobile Radio

Directory of Open Access Journals (Sweden)

Tran Xuan Nam

2004-01-01

Full Text Available We propose a novel scheme of subband adaptive array (SBAA for direct-sequence code division multiple access (DS-CDMA. The scheme exploits the spreading code and pilot signal as the reference signal to estimate the propagation channel. Moreover, instead of combining the array outputs at each output tap using a synthesis filter and then despreading them, we despread directly the array outputs at each output tap by the desired user's code to save the synthesis filter. Although its configuration is far different from that of 2D RAKEs, the proposed scheme exhibits relatively equivalent performance of 2D RAKEs while having less computation load due to utilising adaptive signal processing in subbands. Simulation programs are carried out to explore the performance of the scheme and compare its performance with that of the standard 2D RAKE.

Interference Canceller Based on Cycle-and-Add Property for Single User Detection in DS-CDMA

Science.gov (United States)

Hettiarachchi, Ranga; Yokoyama, Mitsuo; Uehara, Hideyuki; Ohira, Takashi

In this paper, performance of a novel interference cancellation technique for the single user detection in a direct-sequence code-division multiple access (DS-CDMA) system has been investigated. This new algorithm is based on the Cycle-and-Add property of PN (Pseudorandom Noise) sequences and can be applied for both synchronous and asynchronous systems. The proposed strategy provides a simple method that can delete interference signals one by one in spite of the power levels of interferences. Therefore, it is possible to overcome the near-far problem (NFP) in a successive manner without using transmit power control (TPC) techniques. The validity of the proposed procedure is corroborated by computer simulations in additive white Gaussian noise (AWGN) and frequency-nonselective fading channels. Performance results indicate that the proposed receiver outperforms the conventional receiver and, in many cases, it does so with a considerable gain.

Support vector machine multiuser receiver for DS-CDMA signals in multipath channels.

Science.gov (United States)

Chen, S; Samingan, A K; Hanzo, L

2001-01-01

The problem of constructing an adaptive multiuser detector (MUD) is considered for direct sequence code division multiple access (DS-CDMA) signals transmitted through multipath channels. The emerging learning technique, called support vector machines (SVM), is proposed as a method of obtaining a nonlinear MUD from a relatively small training data block. Computer simulation is used to study this SVM MUD, and the results show that it can closely match the performance of the optimal Bayesian one-shot detector. Comparisons with an adaptive radial basis function (RBF) MUD trained by an unsupervised clustering algorithm are discussed.

Performance evaluation of an IMDD optical OFDM-CDMA system.

Science.gov (United States)

Mhatli, Sofien; Mrabet, Hichem; Giacoumidis, Elias; Dayoub, Iyad

2018-03-01

In this paper, we propose a modulation technique for passive optical networks that harnesses two-dimensional prime hop system optical code division multiplexing access (OCDMA) and optical orthogonal frequency-division multiplexing (OFDM) for intensity modulation with direct-detection (IMDD) to enhance users' signal capacity in a cost-effective manner. The theoretical analysis is built from an analytical formula that takes into account both multiple-access interference and photodetector noise. Results show that OFDM-OCDMA with multiple users has similar performance to single-user conventional OOFDM for low transmitted powers.

Multi-Sensor Detection with Particle Swarm Optimization for Time-Frequency Coded Cooperative WSNs Based on MC-CDMA for Underground Coal Mines

Directory of Open Access Journals (Sweden)

Jingjing Xu

2015-08-01

Full Text Available In this paper, a wireless sensor network (WSN technology adapted to underground channel conditions is developed, which has important theoretical and practical value for safety monitoring in underground coal mines. According to the characteristics that the space, time and frequency resources of underground tunnel are open, it is proposed to constitute wireless sensor nodes based on multicarrier code division multiple access (MC-CDMA to make full use of these resources. To improve the wireless transmission performance of source sensor nodes, it is also proposed to utilize cooperative sensors with good channel conditions from the sink node to assist source sensors with poor channel conditions. Moreover, the total power of the source sensor and its cooperative sensors is allocated on the basis of their channel conditions to increase the energy efficiency of the WSN. To solve the problem that multiple access interference (MAI arises when multiple source sensors transmit monitoring information simultaneously, a kind of multi-sensor detection (MSD algorithm with particle swarm optimization (PSO, namely D-PSO, is proposed for the time-frequency coded cooperative MC-CDMA WSN. Simulation results show that the average bit error rate (BER performance of the proposed WSN in an underground coal mine is improved significantly by using wireless sensor nodes based on MC-CDMA, adopting time-frequency coded cooperative transmission and D-PSO algorithm with particle swarm optimization.

Multi-Sensor Detection with Particle Swarm Optimization for Time-Frequency Coded Cooperative WSNs Based on MC-CDMA for Underground Coal Mines.

Science.gov (United States)

Xu, Jingjing; Yang, Wei; Zhang, Linyuan; Han, Ruisong; Shao, Xiaotao

2015-08-27

In this paper, a wireless sensor network (WSN) technology adapted to underground channel conditions is developed, which has important theoretical and practical value for safety monitoring in underground coal mines. According to the characteristics that the space, time and frequency resources of underground tunnel are open, it is proposed to constitute wireless sensor nodes based on multicarrier code division multiple access (MC-CDMA) to make full use of these resources. To improve the wireless transmission performance of source sensor nodes, it is also proposed to utilize cooperative sensors with good channel conditions from the sink node to assist source sensors with poor channel conditions. Moreover, the total power of the source sensor and its cooperative sensors is allocated on the basis of their channel conditions to increase the energy efficiency of the WSN. To solve the problem that multiple access interference (MAI) arises when multiple source sensors transmit monitoring information simultaneously, a kind of multi-sensor detection (MSD) algorithm with particle swarm optimization (PSO), namely D-PSO, is proposed for the time-frequency coded cooperative MC-CDMA WSN. Simulation results show that the average bit error rate (BER) performance of the proposed WSN in an underground coal mine is improved significantly by using wireless sensor nodes based on MC-CDMA, adopting time-frequency coded cooperative transmission and D-PSO algorithm with particle swarm optimization.

Joint Throughput Maximization and Fair Uplink Transmission Scheduling in CDMA Systems

Directory of Open Access Journals (Sweden)

Symeon Papavassiliou

2009-01-01

Full Text Available We study the fundamental problem of optimal transmission scheduling in a code-division multiple-access wireless system in order to maximize the uplink system throughput, while satisfying the users quality-of-service (QoS requirements and maintaining fairness among them. The corresponding problem is expressed as a weighted throughput maximization problem, under certain power and QoS constraints, where the weights are the control parameters reflecting the fairness constraints. With the introduction of the power index capacity, it is shown that this optimization problem can be converted into a binary knapsack problem, where all the corresponding constraints are replaced by the power index capacities at some certain system power index. A two-step approach is followed to obtain the optimal solution. First, a simple method is proposed to find the optimal set of users to receive service for a given fixed target system load, and then the optimal solution is obtained as a global search within a certain range. Furthermore, a stochastic approximation method is presented to effectively identify the required control parameters. The performance evaluation reveals the advantages of our proposed policy over other existing ones and confirms that it achieves very high throughput while maintains fairness among the users, under different channel conditions and requirements.

Code division multiple-access techniques in optical fiber networks. II - Systems performance analysis

Science.gov (United States)

Salehi, Jawad A.; Brackett, Charles A.

1989-08-01

A technique based on optical orthogonal codes was presented by Salehi (1989) to establish a fiber-optic code-division multiple-access (FO-CDMA) communications system. The results are used to derive the bit error rate of the proposed FO-CDMA system as a function of data rate, code length, code weight, number of users, and receiver threshold. The performance characteristics for a variety of system parameters are discussed. A means of reducing the effective multiple-access interference signal by placing an optical hard-limiter at the front end of the desired optical correlator is presented. Performance calculations are shown for the FO-CDMA with an ideal optical hard-limiter, and it is shown that using a optical hard-limiter would, in general, improve system performance.

Dynamic Resource Management in MC-CDMA Based Cellular Wireless Networks

Directory of Open Access Journals (Sweden)

Bala Jeevitha Vani

2009-10-01

Full Text Available Most of the multimedia and Internet services today are asymmetric in nature, and require high data rate support. Allocating equal band width in both uplink and downlink is not prudent solution, as most of the time user requirement is more either in uplink or downlink. The Multi Carrier Code Division Multiple Access (MC-CDMA system with time division duplex mode can easily met this requirement by dynamically declaring traffic direction in TDD slot, and adaptively allocating the sub channels. In this paper, we propose a adaptive slot and sub carrier allocation algorithm, that can be independently implemented in each cell of mobile communication network. Our analytical model is generalization of two cell concept to represent a multi cell model. Based on two cell concept four cases of interference pattern has been considered and simulated separately in presence of Additive White Gaussian Noise (AWGN and Rayleigh Channel. The simulated result suggests the requirement of approximately 9dB of Signal to Noise Ratio (SNR to maintain Bit Error Rate below 10-3. We also analyze the average delay incurred by the proposed algorithm in allocating resources.

Multiuser receiver for DS-CDMA signals in multipath channels: an enhanced multisurface method.

Science.gov (United States)

Mahendra, Chetan; Puthusserypady, Sadasivan

2006-11-01

This paper deals with the problem of multiuser detection in direct-sequence code-division multiple-access (DS-CDMA) systems in multipath environments. The existing multiuser detectors can be divided into two categories: (1) low-complexity poor-performance linear detectors and (2) high-complexity good-performance nonlinear detectors. In particular, in channels where the orthogonality of the code sequences is destroyed by multipath, detectors with linear complexity perform much worse than the nonlinear detectors. In this paper, we propose an enhanced multisurface method (EMSM) for multiuser detection in multipath channels. EMSM is an intermediate piecewise linear detection scheme with a run-time complexity linear in the number of users. Its bit error rate performance is compared with existing linear detectors, a nonlinear radial basis function detector trained by the new support vector learning algorithm, and Verdu's optimal detector. Simulations in multipath channels, for both synchronous and asynchronous cases, indicate that it always outperforms all other linear detectors, performing nearly as well as nonlinear detectors.

A DUAL RESERVATION CDMA-BASED MAC PROTOCOL WITH POWER CONTROL FOR AD HOC NETWORKS

Institute of Scientific and Technical Information of China (English)

Jia Min; Chen Huimin; Yuan Yuhua

2007-01-01

This paper proposes a new multi-channel Medium Access Control (MAC) protocol named as Dual Reservation Code Division Multiple Access (CDMA) based MAC protocol with Power Control (DRCPC). The code channel is divided into common channel, broadcast channel and several data channels. And dynamic power control mechanism is implemented to reduce near-far interference. Compared with IEEE 802.11 Distributed Coordination Function (DCF) protocol, the results show that the proposed mechanism improves the average throughput and limits the transmission delay efficiently.

Principles of spread-spectrum communication systems

CERN Document Server

Torrieri, Don

2015-01-01

This book provides a concise but lucid explanation of the fundamentals of spread-spectrum systems with an emphasis on theoretical principles. The choice of specific topics is tempered by the author’s judgment of their practical significance and interest to both researchers and system designers. The book contains many improved derivations of the classical theory and presents the latest research results that bring the reader to the frontier of the field. This third edition includes new coverage of topics such as CDMA networks, acquisition and synchronization in DS-CDMA cellular networks, hopsets for FH-CDMA ad hoc networks, implications of information theory, the central limit theorem, the power spectral density of FH/CPM complex envelopes, adaptive filters, and adaptive arrays.   ·         Focuses on the fundamentals of spread-spectrum communication systems and provides current examples of their applications ·         Includes problem sets at the end of each chapter to assist readers in co...

A Low-Complexity Joint Synchronization and Detection Algorithm for Single-Band DS-CDMA UWB Communications

Directory of Open Access Journals (Sweden)

Christensen Lars PB

2005-01-01

Full Text Available The problem of asynchronous direct-sequence code-division multiple-access (DS-CDMA detection over the ultra-wideband (UWB multipath channel is considered. A joint synchronization, channel-estimation, and multiuser detection scheme based on the adaptive linear minimum mean square error (LMMSE receiver is presented and evaluated. Further, a novel nonrecursive least-squares algorithm capable of reducing the complexity of the adaptation in the receiver while preserving the advantages of the recursive least-squares (RLS algorithm is presented.

The system capacity view of aging and longevity

Institute of Scientific and Technical Information of China (English)

Jing-Dong J.Han; Lei Hou; Na Sun; Chi Xu; Joseph McDermott; Dan Wang

2017-01-01

Background:Aging is a complex systems level problem that needs a systems level solution.However,system models of aging and longevity,although urgently needed,are still lacking,largely due to the paucity of conceptual frameworks for modeling such a complex process.Results:We propose that aging can be viewed as a decline in system capacity,defined as the maximum level of output that a system produces to fulfill demands.Classical aging hallmarks and anti-aging strategies can be well-aligned to system capacity.Genetic variants responsible for lifespan variation across individuals or species can also be explained by their roles in system capacity.We further propose promising directions to develop systems approaches to modulate system capacity and thus extend both healthspan and lifespan.Conclusions:The system capacity model of aging provides an opportunity to examine aging at the systems level.This model predicts that the extent to which aging can be modulated is normally limited by the upper bound of the system capacity of a species.Within such a boundary,aging can be delayed by moderately increasing an individual's system capacity.Beyond such a boundary,increasing the upper bound is required,which is not unrealistic given the unlimited potential of regenerative medicine in the future,but it requires increasing the capacity of the whole system instead of only part of it.

Modeling the Effect of Bandwidth Allocation on Network Performance

African Journals Online (AJOL)

... The proposed model showed improved performance for CDMA networks, but further increase in the bandwidth did not benefit the network; (iii) A reliability measure such as the spectral efficiency is therefore useful to redeem the limitation in (ii). Keywords: Coverage Capacity, CDMA, Mobile Network, Network Throughput ...

Exploiting Phase Diversity for CDMA2000 1X Smart Antenna Base Stations

Science.gov (United States)

Kim, Seongdo; Hyeon, Seungheon; Choi, Seungwon

2004-12-01

A performance analysis of an access channel decoder is presented which exploits a diversity gain due to the independent magnitude of received signals energy at each of the antenna elements of a smart-antenna base-station transceiver subsystem (BTS) operating in CDMA2000 1X signal environment. The objective is to enhance the data retrieval at cellsite during the access period, for which the optimal weight vector of the smart antenna BTS is not available. It is shown in this paper that the access channel decoder proposed in this paper outperforms the conventional one, which is based on a single antenna channel in terms of detection probability of access probe, access channel failure probability, and Walsh-code demodulation performance.

A Space-Time Signal Decomposition Algorithm for Downlink MIMO DS-CDMA Receivers

Science.gov (United States)

Wang, Yung-Yi; Fang, Wen-Hsien; Chen, Jiunn-Tsair

We propose a dimension reduction algorithm for the receiver of the downlink of direct-sequence code-division multiple access (DS-CDMA) systems in which both the transmitters and the receivers employ antenna arrays of multiple elements. To estimate the high order channel parameters, we develop a layered architecture using dimension-reduced parameter estimation algorithms to estimate the frequency-selective multipath channels. In the proposed architecture, to exploit the space-time geometric characteristics of multipath channels, spatial beamformers and constrained (or unconstrained) temporal filters are adopted for clustered-multipath grouping and path isolation. In conjunction with the multiple access interference (MAI) suppression techniques, the proposed architecture jointly estimates the direction of arrivals, propagation delays, and fading amplitudes of the downlink fading multipaths. With the outputs of the proposed architecture, the signals of interest can then be naturally detected by using path-wise maximum ratio combining. Compared to the traditional techniques, such as the Joint-Angle-and-Delay-Estimation (JADE) algorithm for DOA-delay joint estimation and the space-time minimum mean square error (ST-MMSE) algorithm for signal detection, computer simulations show that the proposed algorithm substantially mitigate the computational complexity at the expense of only slight performance degradation.

Reconfigurable Signal Processing and Hardware Architecture for Broadband Wireless Communications

Directory of Open Access Journals (Sweden)

Liang Ying-Chang

2005-01-01

Full Text Available This paper proposes a broadband wireless transceiver which can be reconfigured to any type of cyclic-prefix (CP -based communication systems, including orthogonal frequency-division multiplexing (OFDM, single-carrier cyclic-prefix (SCCP system, multicarrier (MC code-division multiple access (MC-CDMA, MC direct-sequence CDMA (MC-DS-CDMA, CP-based CDMA (CP-CDMA, and CP-based direct-sequence CDMA (CP-DS-CDMA. A hardware platform is proposed and the reusable common blocks in such a transceiver are identified. The emphasis is on the equalizer design for mobile receivers. It is found that after block despreading operation, MC-DS-CDMA and CP-DS-CDMA have the same equalization blocks as OFDM and SCCP systems, respectively, therefore hardware and software sharing is possible for these systems. An attempt has also been made to map the functional reconfigurable transceiver onto the proposed hardware platform. The different functional entities which will be required to perform the reconfiguration and realize the transceiver are explained.

Exploiting Phase Diversity for CDMA2000 1X Smart Antenna Base Stations

Directory of Open Access Journals (Sweden)

Hyeon Seungheon

2004-01-01

Full Text Available A performance analysis of an access channel decoder is presented which exploits a diversity gain due to the independent magnitude of received signals energy at each of the antenna elements of a smart-antenna base-station transceiver subsystem (BTS operating in CDMA2000 1X signal environment. The objective is to enhance the data retrieval at cellsite during the access period, for which the optimal weight vector of the smart antenna BTS is not available. It is shown in this paper that the access channel decoder proposed in this paper outperforms the conventional one, which is based on a single antenna channel in terms of detection probability of access probe, access channel failure probability, and Walsh-code demodulation performance.

PERILAKU KONSUMEN DALAM MEMILIH JASA LAYANAN OPERATOR MOBILE PHONE YANG BERBASIS CDMA DAN GSM (Studi pada Pelajar dan Mahasiswa Kelompok N-Gens di Kota Malang dari Perpektif Stratejik

Directory of Open Access Journals (Sweden)

Demitri Marvin Kadhaffi

2012-05-01

Full Text Available ABSTRAKS Tujuan penelitian ini adalah (1 menganalisis faktor-faktor yang dipertimbangkan konsumen dalam memilih suatu jasa layanan operator mobile phone (baik CDMA maupun GSM, (2 menganalsis variabel dominan yang mempengaruhi perilaku konsumen dalam memilih jasa layanan operator Jenis penelitian ini adalah applied research dengan metode penelitian studi kausal. Penelitian ini ditujukan pada segmen pelajar dan mahasiswa di Kota Malang yang termasuk kelompok Net Generations (yang lahir antara tahun 1977-1997 dengan batas minimal umur untuk responden adalah 17 tahun.  Kerangka Sampel untuk penelitian ini adalah pengguna kartu CDMA dan GSM sebanyak 175 responden. Tehnik Sampling yang digunakan adalah desain sampel non probability dengan metode purposive sample yang kedua yaitu quota sampling. Metode analisa data yang digunakan adalah analisa faktor dan analisa diskriminan Hasil analisa faktor terhadap 34 variabel diperoleh  7 faktor baru, yang diberi label sebagai berikut : (1 faktor citra produk (2 faktor pelayanan, (3 faktor pengaruh lingkungan, (4 faktor promosi,(5 faktor individual, (6 faktor harga, dan (7 faktor proses. Dari analisa diskriminan diperoleh hasil yang bertentangan dengan hipotesis yaitu ternyata variabel harga bukan merupakan variabel yang dominan dalam membedakan perilaku pelanggan operator CDMA dengan GSM. Mereka lebih sensitif terhadap proses produk. Hal ini mengarahkan pelanggan untuk kalangan pelajar dan mahasiswa sebagai kelompok smart. Hasil penelitian menyimpulkan bahwa untuk membangun keunggulan bersaing operator harus meraih keunggulan posisional melalui diferensiasi “content” jasa yang dihasilkan yaitu berupa proses, sebagai hasil dari aplikasi  positioning produk.   Kata kunci: perilaku konsumen, jasa layanan, mobile phone       ABSTRACT An objective of this research is to (1 identify factors that customer consider in choosing mobile phone operator service (whether CDMA and GSM, (2 identify dominant variable

Kalai-Smorodinsky bargaining solution for optimal resource allocation over wireless DS-CDMA visual sensor networks

Science.gov (United States)

Pandremmenou, Katerina; Kondi, Lisimachos P.; Parsopoulos, Konstantinos E.

2012-01-01

Surveillance applications usually require high levels of video quality, resulting in high power consumption. The existence of a well-behaved scheme to balance video quality and power consumption is crucial for the system's performance. In the present work, we adopt the game-theoretic approach of Kalai-Smorodinsky Bargaining Solution (KSBS) to deal with the problem of optimal resource allocation in a multi-node wireless visual sensor network (VSN). In our setting, the Direct Sequence Code Division Multiple Access (DS-CDMA) method is used for channel access, while a cross-layer optimization design, which employs a central processing server, accounts for the overall system efficacy through all network layers. The task assigned to the central server is the communication with the nodes and the joint determination of their transmission parameters. The KSBS is applied to non-convex utility spaces, efficiently distributing the source coding rate, channel coding rate and transmission powers among the nodes. In the underlying model, the transmission powers assume continuous values, whereas the source and channel coding rates can take only discrete values. Experimental results are reported and discussed to demonstrate the merits of KSBS over competing policies.

Mobile satellite business networks: A part of the European mobile system

Science.gov (United States)

deMateo, M. L.; Jongejans, A.; Loisy, C.; VanHimbeeck, C.; Marchal, J. P.; Borella, A.; Sartori, M.

1995-01-01

The European Space Agency (ESA) is presently procuring an L-band payload EMS, to be embarked on the ITALSAT-2 satellite due for launch in early 1996, in order to promote a regional European mobile system. One of the Land Mobile Communication systems supported by EMS is the MSBN (Mobile Satellite Business Network) voice and data system which will offer the services of a business network on a seamless European coverage. This paper will first recall the characteristics of the MSBN system, which is based on quasi-synchronized CDMA (Code Division Multiple Access) techniques in both directions, and then describe the CDMA receivers implementation. Main validation test results will also be reported confirming predicted performances.

Indoor high precision three-dimensional positioning system based on visible light communication using modified genetic algorithm

Science.gov (United States)

Chen, Hao; Guan, Weipeng; Li, Simin; Wu, Yuxiang

2018-04-01

To improve the precision of indoor positioning and actualize three-dimensional positioning, a reversed indoor positioning system based on visible light communication (VLC) using genetic algorithm (GA) is proposed. In order to solve the problem of interference between signal sources, CDMA modulation is used. Each light-emitting diode (LED) in the system broadcasts a unique identity (ID) code using CDMA modulation. Receiver receives mixed signal from every LED reference point, by the orthogonality of spreading code in CDMA modulation, ID information and intensity attenuation information from every LED can be obtained. According to positioning principle of received signal strength (RSS), the coordinate of the receiver can be determined. Due to system noise and imperfection of device utilized in the system, distance between receiver and transmitters will deviate from the real value resulting in positioning error. By introducing error correction factors to global parallel search of genetic algorithm, coordinates of the receiver in three-dimensional space can be determined precisely. Both simulation results and experimental results show that in practical application scenarios, the proposed positioning system can realize high precision positioning service.

Design, comparative study and analysis of CDMA for different modulation techni

Directory of Open Access Journals (Sweden)

Arun Kumar

2015-11-01

Full Text Available In this work, we have design a MIMO–CDMA using 4 ∗ 8 antennas with the combination of MMSE (Minimum Mean square Error Equalizer for BPSK (Binary Phase shift Keying, QPSK (Quadrature Phase Shift Keying, 16-QAM, 64-QAM and 256-QAM (Quadrature Amplitude Modulation modulation schemes. The analysis is built on the basis of transmit–received signal, constellation and MMSE plot simulated on a MatLab/Simulink. On the basis of BER (Bit-Error-Rate, it is also concluded that this work is mostly suitable for high order modulation schemes as the BER of 16-qam, 64-QAM and 256-QAM is zero. The proposed study has increased the quality of the wireless link and Inter-Symbol-Interference (ISI is likewise cut by applying a combination of MMSE and MIMO (Multiple In and Multiple Out with OSTBC (Orthogonal space Time Block Code encoder and combiner.

Fast converging minimum probability of error neural network receivers for DS-CDMA communications.

Science.gov (United States)

Matyjas, John D; Psaromiligkos, Ioannis N; Batalama, Stella N; Medley, Michael J

2004-03-01

We consider a multilayer perceptron neural network (NN) receiver architecture for the recovery of the information bits of a direct-sequence code-division-multiple-access (DS-CDMA) user. We develop a fast converging adaptive training algorithm that minimizes the bit-error rate (BER) at the output of the receiver. The adaptive algorithm has three key features: i) it incorporates the BER, i.e., the ultimate performance evaluation measure, directly into the learning process, ii) it utilizes constraints that are derived from the properties of the optimum single-user decision boundary for additive white Gaussian noise (AWGN) multiple-access channels, and iii) it embeds importance sampling (IS) principles directly into the receiver optimization process. Simulation studies illustrate the BER performance of the proposed scheme.

Performance of Uplink Fractional Power Control in UTRAN LTE

DEFF Research Database (Denmark)

Úbeda Castellanos, Carlos; López Villa, Dimas; Rosa, Claudio

2008-01-01

UTRAN Long Term Evolution is currently being standardized in 3GPP with the aim of more than double capacity over High-Speed Packet Access. The chosen multiple access for uplink is Single Carrier FDMA, which avoids the intra-cell interference typical for CDMA systems, but it is still sensitive to ...

Estimating cell capacity for multi-cell electrical energy system

Science.gov (United States)

Hashemi, Iman Ahari

A Multi-Cell Electrical Energy System is a set of batteries that are connected in series. The series batteries provide the required voltage necessary for the contraption. After using the energy that is provided by the batteries, some cells within the system tend to have a lower voltage than the other cells. Also, other factors, such as the number of times a battery has been charged or discharged, how long it has been within the system and many other factors, result in some cells having a lesser capacity compared to the other cells within the system. The outcome is that it lowers the required capacity that the electrical energy system is required to provide. By having an unknown cell capacity within the system, it is unknown how much of a charge can be provided to the system so that the cells are not overcharged or undercharged. Therefore, it is necessary to know the cells capacity within the system. Hence, if we were dealing with a single cell, the capacity could be obtained by a full charge and discharge of the cell. In a series system that contains multiple cells a full charging or discharging cannot happen as it might result in deteriorating the structure of some cells within the system. Hence, to find the capacity of a single cell within an electrical energy system it is required to obtain a method that can estimate the value of each cell within the electrical energy system. To approach this method an electrical energy system is required. The electrical energy system consists of rechargeable non-equal capacity batteries to provide the required energy to the system, a battery management system (BMS) board to monitor the cells voltages, an Arduino board that provides the required communication to BMS board, and the PC, and a software that is able to deliver the required data obtained from the Arduino board to the PC. The outcome, estimating the capacity of a cell within a multi-cell system, can be used in many battery related technologies to obtain unknown

Optical code-division multiple-access networks

Science.gov (United States)

Andonovic, Ivan; Huang, Wei

1999-04-01

This review details the approaches adopted to implement classical code division multiple access (CDMA) principles directly in the optical domain, resulting in all optical derivatives of electronic systems. There are a number of ways of realizing all-optical CDMA systems, classified as incoherent and coherent based on spreading in the time and frequency dimensions. The review covers the basic principles of optical CDMA (OCDMA), the nature of the codes used in these approaches and the resultant limitations on system performance with respect to the number of stations (code cardinality), the number of simultaneous users (correlation characteristics of the families of codes), concluding with consideration of network implementation issues. The latest developments will be presented with respect to the integration of conventional time spread codes, used in the bulk of the demonstrations of these networks to date, with wavelength division concepts, commonplace in optical networking. Similarly, implementations based on coherent correlation with the aid of a local oscillator will be detailed and comparisons between approaches will be drawn. Conclusions regarding the viability of these approaches allowing the goal of a large, asynchronous high capacity optical network to be realized will be made.

Promoting evaluation capacity building in a complex adaptive system.

Science.gov (United States)

Lawrenz, Frances; Kollmann, Elizabeth Kunz; King, Jean A; Bequette, Marjorie; Pattison, Scott; Nelson, Amy Grack; Cohn, Sarah; Cardiel, Christopher L B; Iacovelli, Stephanie; Eliou, Gayra Ostgaard; Goss, Juli; Causey, Lauren; Sinkey, Anne; Beyer, Marta; Francisco, Melanie

2018-04-10

This study provides results from an NSF funded, four year, case study about evaluation capacity building in a complex adaptive system, the Nanoscale Informal Science Education Network (NISE Net). The results of the Complex Adaptive Systems as a Model for Network Evaluations (CASNET) project indicate that complex adaptive system concepts help to explain evaluation capacity building in a network. The NISE Network was found to be a complex learning system that was supportive of evaluation capacity building through feedback loops that provided for information sharing and interaction. Participants in the system had different levels of and sources of evaluation knowledge. To be successful at building capacity, the system needed to have a balance between both centralized and decentralized control, coherence, redundancy, and diversity. Embeddedness of individuals within the system also provided support and moved the capacity of the system forward. Finally, success depended on attention being paid to the control of resources. Implications of these findings are discussed. Copyright © 2018 Elsevier Ltd. All rights reserved.

Impact of optical hard limiter on the performance of an optical overlapped-code division multiple access system

Science.gov (United States)

Inaty, Elie; Raad, Robert; Tablieh, Nicole

2011-08-01

Throughout this paper, a closed form expression of the multiple access interference (MAI) limited bit error rate (BER) is provided for the multiwavelength optical code-division multiple-access system when the system is working above the nominal transmission rate limit imposed by the passive encoding-decoding operation. This system is known in literature as the optical overlapped code division multiple access (OV-CDMA) system. A unified analytical framework is presented emphasizing the impact of optical hard limiter (OHL) on the BER performance of such a system. Results show that the performance of the OV-CDMA system may be highly improved when using OHL preprocessing at the receiver side.

CDMA à séquence directe appliqué aux systèmes de communications optiques

OpenAIRE

Lourdiane , Mounia

2005-01-01

Depuis quelques années, le besoin de systèmes de communications plus rapides et plus sures se fait sentir. Le partage entre utilisateurs de la très grande bande passante des fibres optiques nécessite des techniques d'accès adaptées. Afin de répondre à ces besoins, un certain nombre de techniques de multiplexage, dont le CDMA, ont été développées. Cette technique d'accès multiple est déjà largement utilisée dans les systèmes de communications radio-mobiles, que ce soit dans les normes américai...

Quantitative safety assessment of air traffic control systems through system control capacity

Science.gov (United States)

Guo, Jingjing

Quantitative Safety Assessments (QSA) are essential to safety benefit verification and regulations of developmental changes in safety critical systems like the Air Traffic Control (ATC) systems. Effectiveness of the assessments is particularly desirable today in the safe implementations of revolutionary ATC overhauls like NextGen and SESAR. QSA of ATC systems are however challenged by system complexity and lack of accident data. Extending from the idea "safety is a control problem" in the literature, this research proposes to assess system safety from the control perspective, through quantifying a system's "control capacity". A system's safety performance correlates to this "control capacity" in the control of "safety critical processes". To examine this idea in QSA of the ATC systems, a Control-capacity Based Safety Assessment Framework (CBSAF) is developed which includes two control capacity metrics and a procedural method. The two metrics are Probabilistic System Control-capacity (PSC) and Temporal System Control-capacity (TSC); each addresses an aspect of a system's control capacity. And the procedural method consists three general stages: I) identification of safety critical processes, II) development of system control models and III) evaluation of system control capacity. The CBSAF was tested in two case studies. The first one assesses an en-route collision avoidance scenario and compares three hypothetical configurations. The CBSAF was able to capture the uncoordinated behavior between two means of control, as was observed in a historic midair collision accident. The second case study compares CBSAF with an existing risk based QSA method in assessing the safety benefits of introducing a runway incursion alert system. Similar conclusions are reached between the two methods, while the CBSAF has the advantage of simplicity and provides a new control-based perspective and interpretation to the assessments. The case studies are intended to investigate the

A STUDY ON DETERMINING THE REFERENCE SPREADING SEQUENCES FOR A DS/CDMACOMMUNICATION SYSTEM

Directory of Open Access Journals (Sweden)

Cebrail ÇİFTLİKLİ

2002-02-01

Full Text Available In a direct sequence/code division multiple access (DS/CDMA system, the role of the spreading sequences (codes is crucial since the multiple access interference (MAI is the main performance limitation. In this study, we propose an accurate criterion which enables the determination of the reference spreading codes which yield lower bit error rates (BER's in a given code set for a DS/CDMA system using despreading sequences weighted by stepping chip waveforms. The numerical results show that the spreading codes determined by the proposed criterion are the most suitable codes for using as references.

Cross-Layer Resource Allocation for Wireless Visual Sensor Networks and Mobile Ad Hoc Networks

Science.gov (United States)

2014-10-01

are applied to video sequences in order to reduce the bit rate required for storage and/or transmission, while network congestion may result in packet...Wheatley, “On the capacity of a cellular CDMA system,” IEEE Transactions on Vehicular Technology, vol. 40, pp. 303–312, May 1991. [41] K. Pandremmenou

Capacity analysis of spectrum sharing spatial multiplexing MIMO systems

KAUST Repository

Yang, Liang

2014-12-01

This paper considers a spectrum sharing (SS) multiple-input multiple-output (MIMO) system operating in a Rayleigh fading environment. First the capacity of a single-user SS spatial multiplexing system is investigated in two scenarios that assume different receivers. To explicitly show the capacity scaling law of SS MIMO systems, some approximate capacity expressions for the two scenarios are derived. Next, we extend our analysis to a multiple user system with zero-forcing receivers (ZF) under spatially-independent scheduling and analyze the sum-rate. Furthermore, we provide an asymptotic sum-rate analysis to investigate the effects of different parameters on the multiuser diversity gain. Our results show that the secondary system with a smaller number of transmit antennas Nt and a larger number of receive antennas Nr can achieve higher capacity at lower interference temperature Q, but at high Q the capacity follows the scaling law of the conventional MIMO systems. However, for a ZF SS spatial multiplexing system, the secondary system with small Nt and large Nr can achieve the highest capacity throughout the entire region of Q. For a ZF SS spatial multiplexing system with scheduling, the asymptotic sum-rate scales like Ntlog2(Q(KNtNp-1)/Nt), where Np denotes the number of antennas of the primary receiver and K represents the number of secondary transmitters.

Phosphorylation and gene expression of p53 are not affected in human cells exposed to 2.1425 GHz band CW or W-CDMA modulated radiation allocated to mobile radio base stations.

Science.gov (United States)

Hirose, H; Sakuma, N; Kaji, N; Suhara, T; Sekijima, M; Nojima, T; Miyakoshi, J

2006-09-01

A large-scale in vitro study focusing on low-level radiofrequency (RF) fields from mobile radio base stations employing the International Mobile Telecommunication 2000 (IMT-2000) cellular system was conducted to test the hypothesis that modulated RF fields induce apoptosis or other cellular stress response that activate p53 or the p53-signaling pathway. First, we evaluated the response of human cells to microwave exposure at a specific absorption rate (SAR) of 80 mW/kg, which corresponds to the limit of the average whole-body SAR for general public exposure defined as a basic restriction by the International Commission on Non-Ionizing Radiation Protection (ICNIRP) guidelines. Second, we investigated whether continuous wave (CW) and wideband code division multiple access (W-CDMA) modulated signal RF fields at 2.1425 GHz induced apoptosis or any signs of stress. Human glioblastoma A172 cells were exposed to W-CDMA radiation at SARs of 80, 250, and 800 mW/kg, and CW radiation at 80 mW/kg for 24 or 48 h. Human IMR-90 fibroblasts from fetal lungs were exposed to both W-CDMA and CW radiation at a SAR of 80 mW/kg for 28 h. Under the RF field exposure conditions described above, no significant differences in the percentage of apoptotic cells were observed between the test groups exposed to RF signals and the sham-exposed negative controls, as evaluated by the Annexin V affinity assay. No significant differences in expression levels of phosphorylated p53 at serine 15 or total p53 were observed between the test groups and the negative controls by the bead-based multiplex assay. Moreover, microarray hybridization and real-time RT-PCR analysis showed no noticeable differences in gene expression of the subsequent downstream targets of p53 signaling involved in apoptosis between the test groups and the negative controls. Our results confirm that exposure to low-level RF signals up to 800 mW/kg does not induce p53-dependent apoptosis, DNA damage, or other stress response in human

Heat capacity for systems with excited-state quantum phase transitions

Energy Technology Data Exchange (ETDEWEB)

Cejnar, Pavel; Stránský, Pavel, E-mail: stransky@ipnp.troja.mff.cuni.cz

2017-03-18

Heat capacities of model systems with finite numbers of effective degrees of freedom are evaluated using canonical and microcanonical thermodynamics. Discrepancies between both approaches, which are observed even in the infinite-size limit, are particularly large in systems that exhibit an excited-state quantum phase transition. The corresponding irregularity of the spectrum generates a singularity in the microcanonical heat capacity and affects smoothly the canonical heat capacity. - Highlights: • Thermodynamics of systems with excited-state quantum phase transitions • ESQPT-generated singularities of the microcanonical heat capacity • Non-monotonous dependences of the canonical heat capacity • Discord between canonical and microcanonical pictures in the infinite-size limit.

Dynamic quality of service differentiation using fixed code weight in optical CDMA networks

Science.gov (United States)

Kakaee, Majid H.; Essa, Shawnim I.; Abd, Thanaa H.; Seyedzadeh, Saleh

2015-11-01

The emergence of network-driven applications, such as internet, video conferencing, and online gaming, brings in the need for a network the environments with capability of providing diverse Quality of Services (QoS). In this paper, a new code family of novel spreading sequences, called a Multi-Service (MS) code, has been constructed to support multiple services in Optical- Code Division Multiple Access (CDMA) system. The proposed method uses fixed weight for all services, however reducing the interfering codewords for the users requiring higher QoS. The performance of the proposed code is demonstrated using mathematical analysis. It shown that the total number of served users with satisfactory BER of 10-9 using NB=2 is 82, while they are only 36 and 10 when NB=3 and 4 respectively. The developed MS code is compared with variable-weight codes such as Variable Weight-Khazani Syed (VW-KS) and Multi-Weight-Random Diagonal (MW-RD). Different numbers of basic users (NB) are used to support triple-play services (audio, data and video) with different QoS requirements. Furthermore, reference to the BER of 10-12, 10-9, and 10-3 for video, data and audio, respectively, the system can support up to 45 total users. Hence, results show that the technique can clearly provide a relative QoS differentiation with lower value of basic users can support larger number of subscribers as well as better performance in terms of acceptable BER of 10-9 at fixed code weight.

A 10 Gbit/s OCDMA system based on electric encoding and optical transmission

Science.gov (United States)

Li, Chuan-qi; Hu, Jin-lin; He, Dong-dong; Chen, Mei-juan; Wang, Da-chi; Chen, Yan

2013-11-01

An electric encoded/optical transmission system of code division multiple access (CDMA) is proposed. It encodes the user signal in electric domain, and transfers the different code slice signals via the different wavelengths of light. This electric domain encoder/decoder is compared with current traditional encoder/decoder. Four-user modulation/demodulation optical CDMA (OCDMA) system with rate of 2.5 Gbit/s is simulated, which is based on the optical orthogonal code (OCC) designed in our laboratory. The results show that the structure of electric encoding/optical transmission can encode/decode signal correctly, and can achieve the chip rate equal to the user data rate. It can overcome the rate limitation of electronic bottleneck, and bring some potential applications in the electro-optical OCDMA system.

Activation of zero-error classical capacity in low-dimensional quantum systems

Science.gov (United States)

Park, Jeonghoon; Heo, Jun

2018-06-01

Channel capacities of quantum channels can be nonadditive even if one of two quantum channels has no channel capacity. We call this phenomenon activation of the channel capacity. In this paper, we show that when we use a quantum channel on a qubit system, only a noiseless qubit channel can generate the activation of the zero-error classical capacity. In particular, we show that the zero-error classical capacity of two quantum channels on qubit systems cannot be activated. Furthermore, we present a class of examples showing the activation of the zero-error classical capacity in low-dimensional systems.

Étude par co-simulation du principe d'une Interconnexion RF associée à un multiplexage CDMA

OpenAIRE

Mombo Boussougou, Yves Constant; Le Gouguec, Thierry; Quéré, Yves; Huret, Fabrice

2009-01-01

National audience; Dans ce papier nous développons de nouvelles interconnexions, de type radiofréquences, pour remplacer les interconnexions classiques de circuits numériques. A l'aide d'outils de co simulation, nous avons modélisé ce principe d'interconnexion associé à un multiplexage numérique de type CDMA et une modulation d'amplitude. A titre d'exemple, nous présentons la réponse fréquentielle d'un canal radiofréquence ainsi que les différents signaux observables le long de la chaine. Cet...

Transmitter Layering for Multiuser MIMO Systems

Directory of Open Access Journals (Sweden)

Schlegel Christian

2008-01-01

Full Text Available Abstract A novel structure for multiple antenna transmissions utilizing space-time dispersion is proposed, where the original data stream is divided into substreams which are modulated onto all available transmit antennas using stream-specific transmit signature sequences. In order to achieve this, the transmit antennas are partitioned into groups of antennas, called partitions. The signals from the data streams are independently interleaved by partition over the entire transmission frame. The interleaved partitions are then added over all substreams prior to transmission over the MIMO channel. At the receiver, a low-complexity iterative detector adapted from recent CDMA multiuser detection research is used. It is shown that with careful substream power assignments this transmission methodology can efficiently utilize the capacity of rank-deficient channels as it can approach the capacity limits of the multiple antenna channel closely over the entire range of available signal-to-noise ratios and system sizes. This transmission methodology and receiver structure are then applied to multiuser MIMO systems where several multiple antenna terminals communicate concurrently to a joint receiver. It is shown that different received power levels from the different MIMO terminals can be beneficial and that higher spectral efficiencies can be achieved than in the single-terminal case.

Transmitter Layering for Multiuser MIMO Systems

Directory of Open Access Journals (Sweden)

Zachary Bagley

2008-03-01

Full Text Available A novel structure for multiple antenna transmissions utilizing space-time dispersion is proposed, where the original data stream is divided into K substreams which are modulated onto all available transmit antennas using stream-specific transmit signature sequences. In order to achieve this, the transmit antennas are partitioned into M groups of antennas, called partitions. The signals from the K data streams are independently interleaved by partition over the entire transmission frame. The interleaved partitions are then added over all K substreams prior to transmission over the MIMO channel. At the receiver, a low-complexity iterative detector adapted from recent CDMA multiuser detection research is used. It is shown that with careful substream power assignments this transmission methodology can efficiently utilize the capacity of rank-deficient channels as it can approach the capacity limits of the multiple antenna channel closely over the entire range of available signal-to-noise ratios and system sizes. This transmission methodology and receiver structure are then applied to multiuser MIMO systems where several multiple antenna terminals communicate concurrently to a joint receiver. It is shown that different received power levels from the different MIMO terminals can be beneficial and that higher spectral efficiencies can be achieved than in the single-terminal case.

Development of Nuclide Recognizing Prompt Radiation Distribution Monitoring System

Energy Technology Data Exchange (ETDEWEB)

Lee, Uk Jae; Yoo, Dong Han; Kim, Hee Reyoung [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of)

2014-05-15

The geographic data such as latitude, longitude and map image can be obtained by using GPS and digital map. Radiation data can be acquired by detector. Finally simultaneous visibility system can be operated by using CDMA. Existing radiation distribution monitoring system is based on random generated data. However the radiation distribution monitoring system is developed. It is based on real detected data. Connection between the detector and laptop which are located at a site place is operated by using Bluetooth. CDMA is used to simulate visibility system between laptop in a site place and server PC in the control office. Real map image is taken from digital map. Finally radiation distribution contour map on the real map image can be shown by using MATLAB. 5 figures appear which shows natural, {sup 137}Cs, {sup 131}I, artificial and total radiation dose rate. So this system can be used in everywhere to check the distribution of radiation with geographic information.

Network Capacity Assessment and Increase in Systems with Intermittent Water Supply

Directory of Open Access Journals (Sweden)

Amilkar E. Ilaya-Ayza

2016-03-01

Full Text Available Water supply systems have been facing many challenges in recent decades due to the potential effects of climate change and rapid population growth. Water systems need to expand because of demographic growth. Therefore, evaluating and increasing system capacity is crucial. Specifically, we analyze network capacity as one of the main features of a system. When the network capacity starts to decrease, there is a risk that continuous supply will become intermittent. This paper discusses how network expansion carried out throughout the network life span typically reduces network capacity, thus transforming a system originally designed to work with continuous supply into a system with intermittent supply. A method is proposed to expand the network capacity in an environment of economic scarcity through a greedy algorithm that enables the definition of a schedule for pipe modification stages, and thus efficiently expands the network capacity. This method is, at the same time, an important step in the process of changing a water system from intermittent back to continuous supply—an achievement that remains one of the main challenges related to water and health in developing countries.

A Simple Exact Error Rate Analysis for DS-CDMA with Arbitrary Pulse Shape in Flat Nakagami Fading

Science.gov (United States)

Rahman, Mohammad Azizur; Sasaki, Shigenobu; Kikuchi, Hisakazu; Harada, Hiroshi; Kato, Shuzo

A simple exact error rate analysis is presented for random binary direct sequence code division multiple access (DS-CDMA) considering a general pulse shape and flat Nakagami fading channel. First of all, a simple model is developed for the multiple access interference (MAI). Based on this, a simple exact expression of the characteristic function (CF) of MAI is developed in a straight forward manner. Finally, an exact expression of error rate is obtained following the CF method of error rate analysis. The exact error rate so obtained can be much easily evaluated as compared to the only reliable approximate error rate expression currently available, which is based on the Improved Gaussian Approximation (IGA).

A simulation study of capacity utilization to predict future capacity for manufacturing system sustainability

Science.gov (United States)

Rimo, Tan Hauw Sen; Chai Tin, Ong

2017-12-01

Capacity utilization (CU) measurement is an important task in a manufacturing system, especially in make-to-order (MTO) type manufacturing system with product customization, in predicting capacity to meet future demand. A stochastic discrete-event simulation is developed using ARENA software to determine CU and capacity gap (CG) in short run production function. This study focused on machinery breakdown and product defective rate as random variables in the simulation. The study found that the manufacturing system run in 68.01% CU and 31.99% CG. It is revealed that machinery breakdown and product defective rate have a direct relationship with CU. By improving product defective rate into zero defect, manufacturing system can improve CU up to 73.56% and CG decrease to 26.44%. While improving machinery breakdown into zero breakdowns will improve CU up to 93.99% and the CG decrease to 6.01%. This study helps operation level to study CU using “what-if” analysis in order to meet future demand in more practical and easier method by using simulation approach. Further study is recommended by including other random variables that affect CU to make the simulation closer with the real-life situation for a better decision.

Network Capacity Assessment and Increase in Systems with Intermittent Water Supply

OpenAIRE

Ilaya-Ayza, Amilkar Ernesto; Campbell-Gonzalez, Enrique; Pérez García, Rafael; Izquierdo Sebastián, Joaquín

2016-01-01

[EN] Water supply systems have been facing many challenges in recent decades due to the potential effects of climate change and rapid population growth. Water systems need to expand because of demographic growth. Therefore, evaluating and increasing system capacity is crucial. Specifically, we analyze network capacity as one of the main features of a system. When the network capacity starts to decrease, there is a risk that continuous supply will become intermittent. This paper discusses how...

Eliminating four-wave-mixing crosstalk in wavelength-division-multiplexing systems

Science.gov (United States)

Kwong, Wing C.; Yang, Guu-Chang

1996-11-01

To reduce four-wave-mixing crosstalk in long-haul wavelength-division multiplexing (WDM) lightwave systems, the use of unequally spaced channels has recently been proposed. Instead of being solved y integer linear programming, the unequal-spaced channel-allocation problem is here treated as constructing suitable optical orthogonal codes in optical code-division multiple-access (CDMA). Three 'algebraic' algorithms on finding the frequency locations of unequally spaced WDM channels are reported. The constructions are based on generating optical CDMA codewords with a predetermined pulse separation and 'aperiodic' autocorrelation sidelobes no greater than one. The algorithms potentially provide a fast and simple alternative to solve the problem, besides the recently reported computer-search method.

BUFFER CAPACITY IN HETEROGENEOUS MULTICOMPONENT SYSTEMS. REVIEW

Directory of Open Access Journals (Sweden)

Oxana Spinu

2015-12-01

Full Text Available The quantitative basis of the theory of buffer properties for two-phase acid-base buffer systems and for multicomponent heterogeneous systems has been derived. The analytical equations with respect to all components for diverse multicomponent systems were deduced. It has been established, that the buffer capacities of components are mutually proportional.

Impact of dynamic rate coding aspects of mobile phone networks on forensic voice comparison.

Science.gov (United States)

Alzqhoul, Esam A S; Nair, Balamurali B T; Guillemin, Bernard J

2015-09-01

Previous studies have shown that landline and mobile phone networks are different in their ways of handling the speech signal, and therefore in their impact on it. But the same is also true of the different networks within the mobile phone arena. There are two major mobile phone technologies currently in use today, namely the global system for mobile communications (GSM) and code division multiple access (CDMA) and these are fundamentally different in their design. For example, the quality of the coded speech in the GSM network is a function of channel quality, whereas in the CDMA network it is determined by channel capacity (i.e., the number of users sharing a cell site). This paper examines the impact on the speech signal of a key feature of these networks, namely dynamic rate coding, and its subsequent impact on the task of likelihood-ratio-based forensic voice comparison (FVC). Surprisingly, both FVC accuracy and precision are found to be better for both GSM- and CDMA-coded speech than for uncoded. Intuitively one expects FVC accuracy to increase with increasing coded speech quality. This trend is shown to occur for the CDMA network, but, surprisingly, not for the GSM network. Further, in respect to comparisons between these two networks, FVC accuracy for CDMA-coded speech is shown to be slightly better than for GSM-coded speech, particularly when the coded-speech quality is high, but in terms of FVC precision the two networks are shown to be very similar. Copyright © 2015 The Chartered Society of Forensic Sciences. Published by Elsevier Ireland Ltd. All rights reserved.

Jamming protection of spread spectrum RFID system

Science.gov (United States)

Mazurek, Gustaw

2006-10-01

This paper presents a new transform-domain processing algorithm for rejection of narrowband interferences in RFID/DS-CDMA systems. The performance of the proposed algorithm has been verified via computer simulations. Implementation issues have been discussed. The algorithm can be implemented in the FPGA or DSP technology.

Design of a search and rescue terminal based on the dual-mode satellite and CDMA network

Science.gov (United States)

Zhao, Junping; Zhang, Xuan; Zheng, Bing; Zhou, Yubin; Song, Hao; Song, Wei; Zhang, Meikui; Liu, Tongze; Zhou, Li

2010-12-01

The current goal is to create a set of portable terminals with GPS/BD2 dual-mode satellite positioning, vital signs monitoring and wireless transmission functions. The terminal depends on an ARM processor to collect and combine data related to vital signs and GPS/BD2 location information, and sends the message to headquarters through the military CDMA network. It integrates multiple functions as a whole. The satellite positioning and wireless transmission capabilities are integrated into the motherboard, and the vital signs sensors used in the form of belts communicate with the board through Bluetooth. It can be adjusted according to the headquarters' instructions. This kind of device is of great practical significance for operations during disaster relief, search and rescue of the wounded in wartime, non-war military operations and other special circumstances.

Managing the Newsvendor Modeled Product System with Random Capacity and Capacity-Dependent Price

Directory of Open Access Journals (Sweden)

Qingying Li

2015-01-01

Full Text Available We consider a newsvendor modeled product system, where the firm provides products to the market. The supply capacity of the product is random, so the firm receives either the amount of order quantity or the realized capacity, whichever is smaller. The market price is capacity dependent. We consider two types of production cost structures: the procurement case and the in-house production case. The firm pays for the received quantity in the former case and for the ordered quantity in the latter case. We obtain the optimal order quantities for both cases. Comparing with the traditional newsvendor model, we find that the optimal order quantity in both the procurement case and the in-house production case are no greater than that in the traditional newsvendor model with a fixed selling price. We also find that the optimal order quantity for the procurement case is greater than that for the in-house production case. Numerical study is conducted to investigate the sensitivity of the optimal solution versus the distribution of the random capacity/demand.

Determination of SMES capacity to enhance the dynamic stability of power system

International Nuclear Information System (INIS)

Shi, J.; Tang, Y.; Dai, T.; Ren, L.; Li, J.; Cheng, S.

2010-01-01

This paper proposes the principle of SMES capacity determination for power system stable operation. Adopting the energy function method, the mechanism of SMES damping power oscillation in the classical single-machine infinite-bus (SMIB) system is analyzed. The released kinetic energy during disturbance is the original of power system oscillation, which is taken as the principle of SMES capacity determination. Then, the influence of fault type, fault position, and fault clearing time on the SMES capacity determination are discussed. Using MATLAB simulation, the principle of SMES capacity determination is evaluated.

A Utility-Based Downlink Radio Resource Allocation for Multiservice Cellular DS-CDMA Networks

Directory of Open Access Journals (Sweden)

Mahdi Shabany

2007-03-01

Full Text Available A novel framework is proposed to model downlink resource allocation problem in multiservice direct-sequence code division multiple-access (DS-CDMA cellular networks. This framework is based on a defined utility function, which leads to utilizing the network resources in a more efficient way. This utility function quantifies the degree of utilization of resources. As a matter of fact, using the defined utility function, users' channel fluctuations and their delay constraints along with the load conditions of all BSs are all taken into consideration. Unlike previous works, we solve the problem with the general objective of maximizing the total network utility instead of maximizing the achieved utility of each base station (BS. It is shown that this problem is equivalent to finding the optimum BS assignment throughout the network, which is mapped to a multidimensional multiple-choice knapsack problem (MMKP. Since MMKP is NP-hard, a polynomial-time suboptimal algorithm is then proposed to develop an efficient base-station assignment. Simulation results indicate a significant performance improvement in terms of achieved utility and packet drop ratio.

Multilevel LDPC Codes Design for Multimedia Communication CDMA System

Directory of Open Access Journals (Sweden)

Hou Jia

2004-01-01

Full Text Available We design multilevel coding (MLC with a semi-bit interleaved coded modulation (BICM scheme based on low density parity check (LDPC codes. Different from the traditional designs, we joined the MLC and BICM together by using the Gray mapping, which is suitable to transmit the data over several equivalent channels with different code rates. To perform well at signal-to-noise ratio (SNR to be very close to the capacity of the additive white Gaussian noise (AWGN channel, random regular LDPC code and a simple semialgebra LDPC (SA-LDPC code are discussed in MLC with parallel independent decoding (PID. The numerical results demonstrate that the proposed scheme could achieve both power and bandwidth efficiency.

Thermal performance analysis of reciprocating compressor with stepless capacity control system

International Nuclear Information System (INIS)

Bin, Tang; Yuanyang, Zhao; Liansheng, Li; Guangbin, Liu; Le, Wang; Qichao, Yang; Haiping, Xu; Feng, Zhu; Wenhui, Meng

2013-01-01

On the basic principle of stepless capacity control system for large reciprocating compressor, the thermal cycle was analyzed. The equations for the process of suction, reverse flow, compression, discharge and expansion of clearance gas were established. According to these equations, p–V diagrams at various situations were simulated. An experimental platform was setup and the compressor with designed stepless capacity control system run well. The experimental results show that the capacity of compressor can be regulated steplessly, and the motor power is reduced proportionally with respect to the reduction of capacity. During the suction process, both the flow resistance of valve and the pressure fluctuation in cylinder can be reduced by opening the suction valves with the actuators. The simulated and experimental results showed good coincidence. The clearance volume and valve clearance Mach number had a negative influence on the thermal performance of compressor with stepless capacity control system. -- Highlights: ► Flow resistance of valve can be reduced and pressure fluctuation can be reduced. ► Equivalent Mach number of reverse flow is much higher than that of suction process. ► Response of stepless capacity control system is important for regulation accuracy. ► Clearance and valve clearance Mach number have influence on thermal performance

DS-CDMA Receiver Based on a Five-Port Technology

Directory of Open Access Journals (Sweden)

Elvino S. Sousa

2005-07-01

Full Text Available High data rates, low-power consumption, and low complexity will be the most important parameters in the design of the next-generation mobile terminals. In this paper we are introducing a new paradigm in the design of direct sequence spread spectrum receiver by combining analog and digital signal processing. The main difference with respect to the conventional all-digital receiver design approach is that the proposed mixed analog/digital processing results in a symbol rate sampling rather than the high-rate subchip sampling. Analog signal despreading is the key part of the proposed receiver solution, which is based on a five-port device, a passive RF square-law-type device. It is used to perform two important tasks at the same time, namely, the direct conversion and analog despreading. To achieve lower complexity, the proposed receiver uses rectangular instead of pulse-matched despreading at the cost of only a small performance degradation. Also, we propose a new noncoherent pseudonoise (PN code tracking scheme based on error signal generated through the L1 norm. This results in comparable or even better PN code tracking performance than L2 norm circuitry, using less complex hardware. Further, we explore how this technology can be applied in the design of DS-CDMA RAKE receiver for mobile terminals. Depending on how the pilot signal is multiplexed, we propose two types of RAKE receivers. It is shown that under Rayleigh fading channel such receiver structures offer robustness and high performance, while maintaining the low complexity achievable through the five-port device.

The ELLIPSO (tm) system: Elliptical low orbits for mobile communications and other optimum system elements

Science.gov (United States)

Castiel, David

1991-09-01

On 5 Nov. 1990, Ellipsat filed with the FCC the first application to provide voice communication services via low earth orbiting (LEO) satellites. The proposed system, ELLIPSO, aims at achieving end-user costs comparable to those in the cellular industry. On 3 Jun. 1991 Ellipsat filed for the second complement of its system. Ellipsat was also the first company to propose combined position determination and mobile voice services via low-earth orbiting satellites. Ellipsat is still the only proponent of elliptical orbits for any commercial system in the United States. ELLIPSO uses a spectrum efficient combination of FDMA and CDMA techniques. Ellipsat's strategy is to tailor required capacity to user demand, reduce initial system costs and investment risks, and allow the provision of services at affordable end-user prices. ELLIPSO offers optimum features in all the components of its system, elliptical orbits, small satellites, integrated protocol and signalling system, integrated end-user electronics, novel marketing approach based on the cooperation with the tenets of mobile communications, end-user costs that are affordable, and a low risk approach as deployment is tailored to the growth of its customer base. The efficient design of the ELLIPSO constellation and system allows estimated end-user costs in the $.50 per minute range, five to six times less than any other system of comparable capability.

The ELLIPSO (tm) system: Elliptical low orbits for mobile communications and other optimum system elements

Science.gov (United States)

Castiel, David

1991-01-01

On 5 Nov. 1990, Ellipsat filed with the FCC the first application to provide voice communication services via low earth orbiting (LEO) satellites. The proposed system, ELLIPSO, aims at achieving end-user costs comparable to those in the cellular industry. On 3 Jun. 1991 Ellipsat filed for the second complement of its system. Ellipsat was also the first company to propose combined position determination and mobile voice services via low-earth orbiting satellites. Ellipsat is still the only proponent of elliptical orbits for any commercial system in the United States. ELLIPSO uses a spectrum efficient combination of FDMA and CDMA techniques. Ellipsat's strategy is to tailor required capacity to user demand, reduce initial system costs and investment risks, and allow the provision of services at affordable end-user prices. ELLIPSO offers optimum features in all the components of its system, elliptical orbits, small satellites, integrated protocol and signalling system, integrated end-user electronics, novel marketing approach based on the cooperation with the tenets of mobile communications, end-user costs that are affordable, and a low risk approach as deployment is tailored to the growth of its customer base. The efficient design of the ELLIPSO constellation and system allows estimated end-user costs in the $.50 per minute range, five to six times less than any other system of comparable capability.

Optimum capacity determination of stand-alone hybrid generation system considering cost and reliability

International Nuclear Information System (INIS)

Chen, Hung-Cheng

2013-01-01

Highlights: ► This paper presents a methodology for the installation capacity optimization. ► Hybrid generation system is optimized by application of adaptive genetic algorithm. ► A cost investigation is made under various conditions and component characteristics. ► The optimization scheme is validated to meet the annual power load demand. -- Abstract: The aim of this work is to present an optimization methodology for the installation capacity of a stand-alone hybrid generation system, taking into consideration the cost and reliability. Firstly, on the basis of derived steady state models of a wind generator (WG), a photovoltaic array (PV), a battery and an inverter, the hybrid generation system is modeled for the purpose of capacity optimization. Secondly, the power system is analyzed for determining both the system structure and the operation control strategy. Thirdly, according to hourly weather database of wind speed, temperature and solar irradiation, annual power generation capacity is estimated for the system match design in order that an annual power load demand can be met. The capacity determination of a hybrid generation system becomes complicated as a result of the uncertainty in the renewable energy together with load demand and the nonlinearity of system components. Aimed at the power system reliability and the cost minimization, the capacity of a hybrid generation system is optimized by application of an adaptive genetic algorithm (AGA) to individual power generation units. A total cost investigation is made under various conditions, such as wind generator power curves, battery discharge depth and the loss of load probability (LOLP). At the end of this work, the capacity of a hybrid generation system is optimized at two installation sites, namely the offshore Orchid Island and Wuchi in Taiwan. The optimization scheme is validated to optimize power capacities of a photovoltaic array, a battery and a wind turbine generator with a relative

Inactivation of transferrin iron binding capacity by the neutrophil myeloperoxidase system

International Nuclear Information System (INIS)

Clark, R.A.; Pearson, D.W.

1989-01-01

Human serum apotransferrin was exposed to the isolated myeloperoxidase-H2O2-halide system or to phorbol ester-activated human neutrophils. Such treatment resulted in a marked loss in transferrin iron binding capacity as well as concomitant iodination of transferrin. Each component of the cell-free system (myeloperoxidase, H2O2, iodide) or neutrophil system (neutrophils, phorbol ester, iodide) was required in order to observe these changes. In the cell-free system, the H2O2 requirement was fulfilled by either reagent H2O2 or the peroxide-generating system glucose oxidase plus glucose. Both loss of iron binding capacity and transferrin iodination by either the myeloperoxidase system or activated neutrophils were blocked by azide or catalase. The isolated peroxidase system had an acidic pH optimum, whereas the intact cell system was more efficient at neutral pH. The kinetics of changes in iron binding capacity and iodination closely paralleled one another, exhibiting t1/2 values of less than 1 min for the myeloperoxidase-H2O2 system, 3-4 min for the myeloperoxidase-glucose oxidase system, and 8 min for the neutrophil system. That the occupied binding site is protected from the myeloperoxidase system was suggested by (1) a failure to mobilize iron from iron-loaded transferrin, (2) an inverse correlation between initial iron saturation and myeloperoxidase-mediated loss of iron binding capacity, and (3) decreased myeloperoxidase-mediated iodination of iron-loaded versus apotransferrin. Since as little as 1 atom of iodide bound per molecule of transferrin was associated with substantial losses in iron binding capacity, there appears to be a high specificity of myeloperoxidase-catalyzed iodination for residues at or near the iron binding sites. Amino acid analysis of iodinated transferrin (approximately 2 atoms/molecule) demonstrated that iodotyrosine was the predominant iodinated species

The Aviation System Analysis Capability Airport Capacity and Delay Models

Science.gov (United States)

Lee, David A.; Nelson, Caroline; Shapiro, Gerald

1998-01-01

The ASAC Airport Capacity Model and the ASAC Airport Delay Model support analyses of technologies addressing airport capacity. NASA's Aviation System Analysis Capability (ASAC) Airport Capacity Model estimates the capacity of an airport as a function of weather, Federal Aviation Administration (FAA) procedures, traffic characteristics, and the level of technology available. Airport capacity is presented as a Pareto frontier of arrivals per hour versus departures per hour. The ASAC Airport Delay Model allows the user to estimate the minutes of arrival delay for an airport, given its (weather dependent) capacity. Historical weather observations and demand patterns are provided by ASAC as inputs to the delay model. The ASAC economic models can translate a reduction in delay minutes into benefit dollars.

The creation in the French power system of a capacity mechanism and of a capacity market

International Nuclear Information System (INIS)

Meda, Maurice

2014-01-01

The key objective of the French capacity remuneration mechanism is to ensure long term security of supply and to promote peak load containment. The mechanism was set up by the NOME law of December 7, 2010 ('new organisation of the electricity market'), which has changed the organisation of the electricity market and explicitly requires a capacity obligation from suppliers, and by a decree published on December 14, 2012 'concerning the contribution of suppliers to the security of electricity supply and establishing a capacity obligation mechanism in the electricity sector'; further regulation will set up the rules for the capacity mechanism, probably during 2014. The mechanism is decentralized: every supplier has to contribute to supply security and to prove its ability to provide its clients with the capacity they need; all capacity owners in metropolitan France must have their production tools certified. Certificates can be sold and suppliers can buy them to adjust their positions. The transport System operator (TSO) calculates suppliers' obligation, checks if capacity owners fulfil their availability commitment and if suppliers have bought enough certificates. The contribution of interconnections to France's SOS is taken into account implicitly. The decree provides an additional safeguard mechanism, which is centralized: in case a critical situation is observed regarding the electricity supply and demand, the government can organize a call for tender to secure the necessary capacities; the conditions to trigger the call for tender are very restrictive, to ensure the capacity market remains the main investment provider. (author)

Capacity analysis of an automated kit transportation system

NARCIS (Netherlands)

Zijm, W.H.M.; Adan, I.J.B.F.; Buitenhek, R.; Houtum, van G.J.J.A.N.

2000-01-01

In this paper, we present a capacity analysis of an automated transportation system in a flexible assembly factory. The transportation system, together with the workstations, is modeled as a network of queues with multiple job classes. Due to its complex nature, the steadystate behavior of this

Information Processing Capacity of Dynamical Systems

Science.gov (United States)

Dambre, Joni; Verstraeten, David; Schrauwen, Benjamin; Massar, Serge

2012-07-01

Many dynamical systems, both natural and artificial, are stimulated by time dependent external signals, somehow processing the information contained therein. We demonstrate how to quantify the different modes in which information can be processed by such systems and combine them to define the computational capacity of a dynamical system. This is bounded by the number of linearly independent state variables of the dynamical system, equaling it if the system obeys the fading memory condition. It can be interpreted as the total number of linearly independent functions of its stimuli the system can compute. Our theory combines concepts from machine learning (reservoir computing), system modeling, stochastic processes, and functional analysis. We illustrate our theory by numerical simulations for the logistic map, a recurrent neural network, and a two-dimensional reaction diffusion system, uncovering universal trade-offs between the non-linearity of the computation and the system's short-term memory.

Information Processing Capacity of Dynamical Systems

Science.gov (United States)

Dambre, Joni; Verstraeten, David; Schrauwen, Benjamin; Massar, Serge

2012-01-01

Many dynamical systems, both natural and artificial, are stimulated by time dependent external signals, somehow processing the information contained therein. We demonstrate how to quantify the different modes in which information can be processed by such systems and combine them to define the computational capacity of a dynamical system. This is bounded by the number of linearly independent state variables of the dynamical system, equaling it if the system obeys the fading memory condition. It can be interpreted as the total number of linearly independent functions of its stimuli the system can compute. Our theory combines concepts from machine learning (reservoir computing), system modeling, stochastic processes, and functional analysis. We illustrate our theory by numerical simulations for the logistic map, a recurrent neural network, and a two-dimensional reaction diffusion system, uncovering universal trade-offs between the non-linearity of the computation and the system's short-term memory. PMID:22816038

The COMPOSE Project

Science.gov (United States)

Balletta, P.; Biagini, M.; Gallinaro, G.; Vernucci, A.

2003-07-01

This paper provides an overview of the on-going project COMPOSE, an EC co-funded project aiming to define, specify and validate an innovative mobile-services scenario in support of travellers, and to demonstrate the effectiveness of the new proposed location-based value-added services. COMPOSE is supported by organisations belonging to numerous categories covering, as a whole, the entire value-chain of infomobility services provision to the final user. The project team comprises, in addition to the affiliations of the authors, also Teleatlas (NL), ARS T&TT (NL), Alcatel-Bell Space (B), Skysoft (P), Hitech Marketing (A) and MobileGis (IR). The paper describes the services that will be offered to users, encompassing both the pre-trip and the on-trip framework, presents the overall hybrid system architecture also including a via-satellite component based upon the Wideband-CDMA (W-CDMA) technique adopted in UMTS, discusses the access solutions envisaged for that component permitting multiple feeder-link stations to share the CDMA multiplex capacity by directly transmitting their codes to the satellite, and illustrates the results of some computer simulations intended to assess the performance of said access solutions, with regard to the effects of the inevitable up- link frequency errors and transponder non-linearity.

Perbandingan Perhitungan Trafik Jam Sibuk CDMA 2000 1x pada BTS Inner City dan BTS Outer City dengan Mempergunakan Metode ADPH, TCBH, FDMH dan FDMP

Directory of Open Access Journals (Sweden)

Eka Wahyudi

2013-11-01

Full Text Available Cellular communication system is a wireless communication system where the subscriber can move within a wide network coverage. Code Division Multiple Access (CDMA is a multiuser access technology that is each user uses a unique code contained in the access channel in the system. Calculation and determination of peak hours can be done by several methods such as: Average Daily Peak Hour (ADPH, Time Consistent Busy Hour (TCBH, Fixed Daily Measurement Hour (FDMH, Fixed Daily Measurement Period (FDMP. The effectiveness of the channel should be determined by occupancy both at inner city territory and outer city  territory location. Using design Erlang (Erl for supply channel at Base Transceiver Station (BTS that provided, BTS has a design Erlang of 369,83 Erl at inner city and it has a design Erlang of 241,8 Erl at outer city. Peak hour on the inner city occurred at 12:00 to 15:00, whereas the outer city of peak hour occurred at 18:00 to 21:00. Effectiveness value that determined by operator are : 70% = high occupancy (very effective. In this case occupancy values obtained in each method is between 21% to 69% which means effective

Dynamic Buffer Capacity in Acid-Base Systems.

Science.gov (United States)

Michałowska-Kaczmarczyk, Anna M; Michałowski, Tadeusz

The generalized concept of 'dynamic' buffer capacity β V is related to electrolytic systems of different complexity where acid-base equilibria are involved. The resulting formulas are presented in a uniform and consistent form. The detailed calculations are related to two Britton-Robinson buffers, taken as examples.

Dynamic Buffer Capacity in Acid?Base Systems

OpenAIRE

Micha?owska-Kaczmarczyk, Anna M.; Micha?owski, Tadeusz

2015-01-01

The generalized concept of ?dynamic? buffer capacity ? V is related to electrolytic systems of different complexity where acid?base equilibria are involved. The resulting formulas are presented in a uniform and consistent form. The detailed calculations are related to two Britton?Robinson buffers, taken as examples.

Liquid heat capacity of the solvent system (piperazine + n-methyldiethanolamine + water)

International Nuclear Information System (INIS)

Chen, Y.-R.; Caparanga, Alvin R.; Soriano, Allan N.; Li, M.-H.

2010-01-01

A new set of values for the heat capacity of aqueous mixtures of piperazine (PZ) and n-methyldiethanolamine (MDEA) at different concentrations and temperatures are reported in this paper. The differential scanning calorimetry technique was used to measure the property over the range T = 303.2 K to T = 353.2 K for mixtures containing 0.60 to 0.90 mole fraction water with 15 different concentrations of the system (PZ + MDEA + H 2 O). Heat capacity for four concentrations of the binary system (PZ + MDEA) was also measured. A Redlich-Kister-type equation was adopted to estimate the excess molar heat capacity, which was used to predict the value of the molar heat capacity at a particular concentration and temperature, which would then be compared against the measured value. A total of 165 data points fit into the model resulted in a low overall average absolute deviation of 4.6% and 0.3% for the excess molar heat capacity and molar heat capacity, respectively. Thus, the results presented here are of acceptable accuracy for use in engineering process design.

Capacity analysis of spectrum sharing spatial multiplexing MIMO systems

KAUST Repository

Yang, Liang; Qaraqe, Khalid A.; Serpedin, Erchin; Alouini, Mohamed-Slim

2014-01-01

This paper considers a spectrum sharing (SS) multiple-input multiple-output (MIMO) system operating in a Rayleigh fading environment. First the capacity of a single-user SS spatial multiplexing system is investigated in two scenarios that assume

Radioactive waste integrated management system

International Nuclear Information System (INIS)

Song, D. Y.; Choi, S. S.; Han, B. S.

2003-01-01

In this paper, we present an integrated management system for radioactive waste, which can keep watch on the whole transporting process of each drum from nuclear power plant temporary storage house to radioactive waste storage house remotely. Our approach use RFID(Radio Frequency Identification) system, which can recognize the data information without touch, GSP system, which can calculate the current position precisely using the accurate time and distance measured from satellites, and the spread spectrum technology CDMA, which is widely used in the area of mobile communication

Radioactive waste integrated management system

Energy Technology Data Exchange (ETDEWEB)

Song, D Y; Choi, S S; Han, B S [Atomic Creative Technology, Taejon (Korea, Republic of)

2003-10-01

In this paper, we present an integrated management system for radioactive waste, which can keep watch on the whole transporting process of each drum from nuclear power plant temporary storage house to radioactive waste storage house remotely. Our approach use RFID(Radio Frequency Identification) system, which can recognize the data information without touch, GSP system, which can calculate the current position precisely using the accurate time and distance measured from satellites, and the spread spectrum technology CDMA, which is widely used in the area of mobile communication.

Capacity on wireless quantum cellular communication system

Science.gov (United States)

Zhou, Xiang-Zhen; Yu, Xu-Tao; Zhang, Zai-Chen

2018-03-01

Quantum technology is making excellent prospects in future communication networks. Entanglement generation and purification are two major components in quantum networks. Combining these two techniques with classical cellular mobile communication, we proposed a novel wireless quantum cellular(WQC) communication system which is possible to realize commercial mobile quantum communication. In this paper, the architecture and network topology of WQC communication system are discussed, the mathematical model of WQC system is extracted and the serving capacity, indicating the ability to serve customers, is defined and calculated under certain circumstances.

Capacity limits of spectrum-sharing systems over hyper-fading channels

KAUST Repository

Ekin, Sabit

2011-01-20

Cognitive radio (CR) with spectrum-sharing feature is a promising technique to address the spectrum under-utilization problem in dynamically changing environments. In this paper, the achievable capacity gain of spectrum-sharing systems over dynamic fading environments is studied. To perform a general analysis, a theoretical fading model called hyper-fading model that is suitable to the dynamic nature of CR channel is proposed. Closed-form expressions of probability density function (PDF) and cumulative density function (CDF) of the signal-to-noise ratio (SNR) for secondary users (SUs) in spectrum-sharing systems are derived. In addition, the capacity gains achievable with spectrum-sharing systems in high and low power regions are obtained. The effects of different fading figures, average fading powers, interference temperatures, peak powers of secondary transmitters, and numbers of SUs on the achievable capacity are investigated. The analytical and simulation results show that the fading figure of the channel between SUs and primary base-station (PBS), which describes the diversity of the channel, does not contribute significantly to the system performance gain. © 2011 John Wiley & Sons, Ltd.

Capacity limits of spectrum-sharing systems over hyper-fading channels

KAUST Repository

Ekin, Sabit; Yilmaz, Ferkan; Ç elebi, Hasari Burak; Qaraqe, Khalid A.; Alouini, Mohamed-Slim; Serpedin, Erchin

2011-01-01

Cognitive radio (CR) with spectrum-sharing feature is a promising technique to address the spectrum under-utilization problem in dynamically changing environments. In this paper, the achievable capacity gain of spectrum-sharing systems over dynamic fading environments is studied. To perform a general analysis, a theoretical fading model called hyper-fading model that is suitable to the dynamic nature of CR channel is proposed. Closed-form expressions of probability density function (PDF) and cumulative density function (CDF) of the signal-to-noise ratio (SNR) for secondary users (SUs) in spectrum-sharing systems are derived. In addition, the capacity gains achievable with spectrum-sharing systems in high and low power regions are obtained. The effects of different fading figures, average fading powers, interference temperatures, peak powers of secondary transmitters, and numbers of SUs on the achievable capacity are investigated. The analytical and simulation results show that the fading figure of the channel between SUs and primary base-station (PBS), which describes the diversity of the channel, does not contribute significantly to the system performance gain. © 2011 John Wiley & Sons, Ltd.

Should fully autonomous artificial intelligence systems be granted legal capacity?

OpenAIRE

Naučius, Mindaugas

2018-01-01

The aim of this article is to address the issue of granting legal capacity to artificial inteligence systems. In order to approach the solution to the problem addressed, the article includes several aspects, relevant in order to achieve it. To begin with, the general concept of legal capacity is introduced. Following this aspect, the main features of both natural and juridical persons are addressed, in order to become familiar with the content of legal capacity, or in other words, to be aware...

Analysis of a Combined Antenna Arrays and Reverse-Link Synchronous DS-CDMA System over Multipath Rician Fading Channels

Directory of Open Access Journals (Sweden)

Kim Yong-Seok

2005-01-01

Full Text Available We present the BER analysis of antenna array (AA receiver in reverse-link asynchronous multipath Rician channels and analyze the performance of an improved AA system which applies a reverse-link synchronous transmission technique (RLSTT in order to effectively make a better estimation of covariance matrices at a beamformer-RAKE receiver. In this work, we provide a comprehensive analysis of user capacity which reflects several important factors such as the ratio of the specular component power to the Rayleigh fading power, the shape of multipath intensity profile, and the number of antennas. Theoretical analysis demonstrates that for the case of a strong specular path's power or for a high decay factor, the employment of RLSTT along with AA has the potential of improving the achievable capacity by an order of magnitude.

Farming System Evolution and Adaptive Capacity: Insights for Adaptation Support

Directory of Open Access Journals (Sweden)

Jami L. Dixon

2014-02-01

Full Text Available Studies of climate impacts on agriculture and adaptation often provide current or future assessments, ignoring the historical contexts farming systems are situated within. We investigate how historical trends have influenced farming system adaptive capacity in Uganda using data from household surveys, semi-structured interviews, focus-group discussions and observations. By comparing two farming systems, we note three major findings: (1 similar trends in farming system evolution have had differential impacts on the diversity of farming systems; (2 trends have contributed to the erosion of informal social and cultural institutions and an increasing dependence on formal institutions; and (3 trade-offs between components of adaptive capacity are made at the farm-scale, thus influencing farming system adaptive capacity. To identify the actual impacts of future climate change and variability, it is important to recognize the dynamic nature of adaptation. In practice, areas identified for further adaptation support include: shift away from one-size-fits-all approach the identification and integration of appropriate modern farming method; a greater focus on building inclusive formal and informal institutions; and a more nuanced understanding regarding the roles and decision-making processes of influential, but external, actors. More research is needed to understand farm-scale trade-offs and the resulting impacts across spatial and temporal scales.

A Brief Survey of Media Access Control, Data Link Layer, and Protocol Technologies for Lunar Surface Communications

Science.gov (United States)

Wallett, Thomas M.

2009-01-01

This paper surveys and describes some of the existing media access control and data link layer technologies for possible application in lunar surface communications and the advanced wideband Direct Sequence Code Division Multiple Access (DSCDMA) conceptual systems utilizing phased-array technology that will evolve in the next decade. Time Domain Multiple Access (TDMA) and Code Division Multiple Access (CDMA) are standard Media Access Control (MAC) techniques that can be incorporated into lunar surface communications architectures. Another novel hybrid technique that is recently being developed for use with smart antenna technology combines the advantages of CDMA with those of TDMA. The relatively new and sundry wireless LAN data link layer protocols that are continually under development offer distinct advantages for lunar surface applications over the legacy protocols which are not wireless. Also several communication transport and routing protocols can be chosen with characteristics commensurate with smart antenna systems to provide spacecraft communications for links exhibiting high capacity on the surface of the Moon. The proper choices depend on the specific communication requirements.

Achievable capacity of a spectrum sharing system over hyper fading channels

KAUST Repository

Ekin, Sabit

2009-11-01

Cognitive radio with spectrum sharing feature is a promising technique to address the spectrum under-utilization problem in dynamically changing environments. In this paper, achievable capacity gain of spectrum sharing systems over dynamic fading environments is studied. For the analysis, a theoretical fading model called hyper fading model that is suitable to the dynamic nature of cognitive radio channel is proposed. Closed-form expression of probability density function (PDF) and cumulative density function (CDF) of the signal-to-noise ratio (SNR) for secondary users in spectrum sharing systems are derived. In addition, the capacity gains achievable with spectrum sharing systems in high and low power regions are obtained. Numerical simulations are performed to study the effects of different fading figures, average powers, interference temperature, and number of secondary users on the achievable capacity.

Capacity Estimation and Near-Capacity Achieving Techniques for Digitally Modulated Communication Systems

DEFF Research Database (Denmark)

Yankov, Metodi Plamenov

investigation will include linear interference channels of high dimensionality (such as multiple-input multiple-output), and the non-linear optical fiber channel, which has been gathering more and more attention from the information theory community in recent years. In both cases novel CCC estimates and lower......This thesis studies potential improvements that can be made to the current data rates of digital communication systems. The physical layer of the system will be investigated in band-limited scenarios, where high spectral efficiency is necessary in order to meet the ever-growing data rate demand....... Several issues are tackled, both with theoretical and more practical aspects. The theoretical part is mainly concerned with estimating the constellation constrained capacity (CCC) of channels with discrete input, which is an inherent property of digital communication systems. The channels under...

Growing organizational capacity through a systems approach: one health network's experience.

Science.gov (United States)

MacKenzie, Richard; Capuano, Terry; Durishin, Linda Drexinger; Stern, Glen; Burke, James B

2008-02-01

Hospitals are reporting unexpected surges in demand for services. Lehigh Valley Hospital challenged its clinical and administrative staff to increase capacity by at least 4% per year using an interdepartmental, systemwide initiative, Growing Organizational Capacity (GOC). Following a systemwide leadership retreat that yielded more than 1,000 ideas, the initiative's principal sponsor convened a cross-functional improvement team. During a two-year period, 17 projects were implemented. Using a complex systems approach, improvement ideas "emerged" from microsystems at the points of care. Through rigorous reporting and testing of process adaptations, need, data, and people drove innovation. Hundreds of multilevel clinical and administrative staff redesigned processes and roles to increase organizational capacity. Admissions rose by 6.1%, 5.5 %, 8.7%, 5.0%, and 3.8% in fiscal years 2003 through 2007, respectively. Process enhancements cost approximately $1 million, while increased revenues attributable to increased capacity totaled $2.5 million. Multiple, coordinated, and concurrent projects created a greater impact than that possible with a single project. GOC and its success, best explained in the context of complex adaptive systems and microsystem theories, are transferrable to throughput issues that challenge efficiency and effectiveness in other health care systems.

High security chaotic multiple access scheme for visible light communication systems with advanced encryption standard interleaving

Science.gov (United States)

Qiu, Junchao; Zhang, Lin; Li, Diyang; Liu, Xingcheng

2016-06-01

Chaotic sequences can be applied to realize multiple user access and improve the system security for a visible light communication (VLC) system. However, since the map patterns of chaotic sequences are usually well known, eavesdroppers can possibly derive the key parameters of chaotic sequences and subsequently retrieve the information. We design an advanced encryption standard (AES) interleaving aided multiple user access scheme to enhance the security of a chaotic code division multiple access-based visible light communication (C-CDMA-VLC) system. We propose to spread the information with chaotic sequences, and then the spread information is interleaved by an AES algorithm and transmitted over VLC channels. Since the computation complexity of performing inverse operations to deinterleave the information is high, the eavesdroppers in a high speed VLC system cannot retrieve the information in real time; thus, the system security will be enhanced. Moreover, we build a mathematical model for the AES-aided VLC system and derive the theoretical information leakage to analyze the system security. The simulations are performed over VLC channels, and the results demonstrate the effectiveness and high security of our presented AES interleaving aided chaotic CDMA-VLC system.

Improving Power System Modeling. A Tool to Link Capacity Expansion and Production Cost Models

Energy Technology Data Exchange (ETDEWEB)

Diakov, Victor [National Renewable Energy Lab. (NREL), Golden, CO (United States); Cole, Wesley [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sullivan, Patrick [National Renewable Energy Lab. (NREL), Golden, CO (United States); Brinkman, Gregory [National Renewable Energy Lab. (NREL), Golden, CO (United States); Margolis, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2015-11-01

Capacity expansion models (CEM) provide a high-level long-term view at the prospects of the evolving power system. In simulating the possibilities of long-term capacity expansion, it is important to maintain the viability of power system operation in the short-term (daily, hourly and sub-hourly) scales. Production-cost models (PCM) simulate routine power system operation on these shorter time scales using detailed load, transmission and generation fleet data by minimizing production costs and following reliability requirements. When based on CEM 'predictions' about generating unit retirements and buildup, PCM provide more detailed simulation for the short-term system operation and, consequently, may confirm the validity of capacity expansion predictions. Further, production cost model simulations of a system that is based on capacity expansion model solution are 'evolutionary' sound: the generator mix is the result of logical sequence of unit retirement and buildup resulting from policy and incentives. The above has motivated us to bridge CEM with PCM by building a capacity expansion - to - production cost model Linking Tool (CEPCoLT). The Linking Tool is built to onset capacity expansion model prescriptions onto production cost model inputs. NREL's ReEDS and Energy Examplar's PLEXOS are the capacity expansion and the production cost models, respectively. Via the Linking Tool, PLEXOS provides details of operation for the regionally-defined ReEDS scenarios.

Harnessing the sun: Developing capacity to sustain local solar energy systems

Science.gov (United States)

Olarewaju, Olufemi

2011-12-01

Use of solar photovoltaic (PV) and other renewable sources to meet rising electricity demand by a growing world population has gained traction in many countries in recent years. In rural Sub-Saharan Africa, where 86 percent of the populace has no access to electricity, solar energy systems represent partial solutions to demand, especially in support of rural development initiatives to supply potable water, health care services and education. Unfortunately, development of human and organizational capacity to maintain solar technology has not kept pace with the rate of installation, causing many to fall into disrepair and disuse. This has stimulated interest in capacity development processes required to make solar systems sustainable. To cast light on the practical meanings and challenges of capacity development for solar energy, this study compares the experiences of two rural projects, one in Lagos State (Nigeria) that disregarded the importance of capacity development, and the other in Texas (United States) that, in contrast, made such development the centerpiece of its operations. Based largely on interviews with 60 key actors, findings underscore the crucial importance of sustained investment in capacity development to assurance of durable power supply from renewable sources.

Hydrophobic interaction chromatography in dual salt system increases protein binding capacity.

Science.gov (United States)

Senczuk, Anna M; Klinke, Ralph; Arakawa, Tsutomu; Vedantham, Ganesh; Yigzaw, Yinges

2009-08-01

Hydrophobic interaction chromatography (HIC) uses weakly hydrophobic resins and requires a salting-out salt to promote protein-resin interaction. The salting-out effects increase with protein and salt concentration. Dynamic binding capacity (DBC) is dependent on the binding constant, as well as on the flow characteristics during sample loading. DBC increases with the salt concentration but decreases with increasing flow rate. Dynamic and operational binding capacity have a major raw material cost/processing time impact on commercial scale production of monoclonal antibodies. In order to maximize DBC the highest salt concentration without causing precipitation is used. We report here a novel method to maintain protein solubility while increasing the DBC by using a combination of two salting-out salts (referred to as dual salt). In a series of experiments, we explored the dynamic capacity of a HIC resin (TosoBioscience Butyl 650M) with combinations of salts. Using a model antibody, we developed a system allowing us to increase the dynamic capacity up to twofold using the dual salt system over traditional, single salt system. We also investigated the application of this novel approach to several other proteins and salt combinations, and noted a similar protein solubility and DBC increase. The observed increase in DBC in the dual salt system was maintained at different linear flow rates and did not impact selectivity.

Classification of reserve capacity in future power systems

NARCIS (Netherlands)

Frunt, J.; Kling, W.L.; Myrzik, J.M.A.

2009-01-01

In electrical power systems must always be a balance between supply and demand. Any imbalance will result in a frequency deviation. To reduce the imbalance to zero, ancillary services for balancing are in use. Ancillary services are characterised by their deployment time and their capacity. By using

An optical CDMA system based on chaotic sequences

Science.gov (United States)

Liu, Xiao-lei; En, De; Wang, Li-guo

2014-03-01

In this paper, a coherent asynchronous optical code division multiple access (OCDMA) system is proposed, whose encoder/decoder is an all-optical generator. This all-optical generator can generate analog and bipolar chaotic sequences satisfying the logistic maps. The formula of bit error rate (BER) is derived, and the relationship of BER and the number of simultaneous transmissions is analyzed. Due to the good property of correlation, this coherent OCDMA system based on these bipolar chaotic sequences can support a large number of simultaneous users, which shows that these chaotic sequences are suitable for asynchronous OCDMA system.

Dynamic simulation of variable capacity refrigeration systems under abnormal conditions

International Nuclear Information System (INIS)

Liang Nan; Shao Shuangquan; Tian Changqing; Yan Yuying

2010-01-01

There are often abnormal working conditions at evaporator outlet of a refrigeration system, such as two-phase state in transient process, and it is essential to investigate such transient behaviours for system design and control strategy. In this paper, a dynamic lumped parameter model is developed to simulate the transient behaviours of refrigeration system with variable capacity in both normal and abnormal working conditions. The appropriate discriminant method is adopted to switch the normal and abnormal conditions smoothly and to eliminate the simulated data oscillation. In order to verify the dynamic model, we built a test system with variable frequency compressor, water-cooling condenser, evaporator and electronic expansion valve. Calculated values from the mathematical model show reasonable agreement with the experimental data. The simulation results show that the transient behaviours of the variable capacity refrigeration system in the abnormal working conditions can be calculated reliably with the dynamic model when the compressor rotary speed or the opening of electronic expansion valve changes abruptly.

Capacity Building in Open Medical Record System (OpenMRS) in ...

International Development Research Centre (IDRC) Digital Library (Canada)

Capacity Building in Open Medical Record System (OpenMRS) in Rwanda ... Partners in Health (PIH), an international nongovernmental organization, has demonstrated the usefulness of ... Journal articles ... will fund social science, population and public health, and health systems research relevant to the emerging crisis.

Impact of Operating Rules on Planning Capacity Expansion of Urban Water Supply Systems

Science.gov (United States)

de Neufville, R.; Galelli, S.; Tian, X.

2017-12-01

This study addresses the impact of operating rules on capacity planning of urban water supply systems. The continuous growth of metropolitan areas represents a major challenge for water utilities, which often rely on industrial water supply (e.g., desalination, reclaimed water) to complement natural resources (e.g., reservoirs). These additional sources increase the reliability of supply, equipping operators with additional means to hedge against droughts. How do their rules for using industrial water supply impact the performance of water supply system? How might it affect long-term plans for capacity expansion? Possibly significantly, as demonstrated by the analysis of the operations and planning of a water supply system inspired by Singapore. Our analysis explores the system dynamics under multiple inflow and management scenarios to understand the extent to which alternative operating rules for the use of industrial water supply affect system performance. Results first show that these operating rules can have significant impact on the variability in system performance (e.g., reliability, energy use) comparable to that of hydro-climatological conditions. Further analyses of several capacity expansion exercises—based on our original hydrological and management scenarios—show that operating rules significantly affect the timing and magnitude of critical decisions, such as the construction of new desalination plants. These results have two implications: Capacity expansion analysis should consider the effect of a priori uncertainty about operating rules; and operators should consider how their flexibility in operating rules can affect their perceived need for capacity.

Air conditioning system with supplemental ice storing and cooling capacity

Science.gov (United States)

Weng, Kuo-Lianq; Weng, Kuo-Liang

1998-01-01

The present air conditioning system with ice storing and cooling capacity can generate and store ice in its pipe assembly or in an ice storage tank particularly equipped for the system, depending on the type of the air conditioning system. The system is characterized in particular in that ice can be produced and stored in the air conditioning system whereby the time of supplying cooled air can be effectively extended with the merit that the operation cycle of the on and off of the compressor can be prolonged, extending the operation lifespan of the compressor in one aspect. In another aspect, ice production and storage in great amount can be performed in an off-peak period of the electrical power consumption and the stored ice can be utilized in the peak period of the power consumption so as to provide supplemental cooling capacity for the compressor of the air conditioning system whereby the shift of peak and off-peak power consumption can be effected with ease. The present air conditioning system can lower the installation expense for an ice-storing air conditioning system and can also be applied to an old conventional air conditioning system.

Entanglement Capacity of Two-Qubit Unitary Operator with the Help of Auxiliary System

International Nuclear Information System (INIS)

Hu Baolin; Di Yaomin

2007-01-01

The entanglement capacity of general two-qubit unitary operators is studied when auxiliary systems are allowed, and the analytical results based on linear entropy when input states are disentangled are given. From the results the condition for perfect entangler, α 1 = α 2 = π/4, is obtained. Contrary to the case without auxiliary system, the parameter α 3 may play active role to the entanglement capacity when auxiliary systems are allowed.

The Analysis and the Performance Simulation of the Capacity of Bit-interleaved Coded Modulation System

Directory of Open Access Journals (Sweden)

Hongwei ZHAO

2014-09-01

Full Text Available In this paper, the capacity of the BICM system over AWGN channels is first analyzed; the curves of BICM capacity versus SNR are also got by the Monte-Carlo simulations===?=== and compared with the curves of the CM capacity. Based on the analysis results, we simulate the error performances of BICM system with LDPC codes. Simulation results show that the capacity of BICM system with LDPC codes is enormously influenced by the mapping methods. Given a certain modulation method, the BICM system can obtain about 2-3 dB gain with Gray mapping compared with Non-Gray mapping. Meanwhile, the simulation results also demonstrate the correctness of the theory analysis.

SE Capstone Project: Building Systems Engineering Education and Workforce Capacity

Science.gov (United States)

2012-04-01

This project developed a system to improve fuel efficiency by means of regenerative braking . The team designed a simple system that allows "bolt-on...air traffic control, social networking, credit/debit cards, and anti-lock brakes are only a few functions enabled by complex systems of systems . We...Building Systems Engineering Education and Workforce Capacity SE Capstone Project APRIL 2012 Report Documentation Page Form ApprovedOMB No. 0704

Capacity analysis of automatic transport systems in an assembly factory

NARCIS (Netherlands)

Zijm, W.H.M.; Lenstra, J.K.; Tijms, H.C.; Volgenant, A.

1989-01-01

We describe a case study concerning the capacity analysis of a completely automated transport system in a flexible assembly environment. Basically, the system is modelled as a network of queues, however, due to its complex nature, product-form network theory is not applicable. Instead, we present an

Higher order capacity statistics of multi-hop transmission systems over Rayleigh fading channels

KAUST Repository

Yilmaz, Ferkan

2012-03-01

In this paper, we present an exact analytical expression to evaluate the higher order statistics of the channel capacity for amplify and forward (AF) multihop transmission systems operating over Rayleigh fading channels. Furthermore, we present simple and efficient closed-form expression to the higher order moments of the channel capacity of dual hop transmission system with Rayleigh fading channels. In order to analyze the behavior of the higher order capacity statistics and investigate the usefulness of the mathematical analysis, some selected numerical and simulation results are presented. Our results are found to be in perfect agreement. © 2012 IEEE.

MIMO channel capacity versus mutual coupling in multi antenna element system

DEFF Research Database (Denmark)

Thaysen, Jesper; Jakobsen, Kaj Bjarne

2004-01-01

In this paper the influence of mutual coupling on the capacity of a multiple-input multiple-output (MIMO) antenna system is demonstrated. No direct relation between the envelope correlation and the actual location and orientation of the antennas is found. Even though being essential for high MIMO...... capacity, configurations with the lowest envelope correlations are not necessarily the most suitable for a MIMO system. A certain bandwidth is required as well. Three planar inverted F-antennas (PIFA) located on the same 40 mm x 100 mm ground plane. The antennas that haves a resonant frequency of 1.8 GHz...

Bridging complexity theory and resilience to develop surge capacity in health systems.

Science.gov (United States)

Therrien, Marie-Christine; Normandin, Julie-Maude; Denis, Jean-Louis

2017-03-20

Purpose Health systems are periodically confronted by crises - think of Severe Acute Respiratory Syndrome, H1N1, and Ebola - during which they are called upon to manage exceptional situations without interrupting essential services to the population. The ability to accomplish this dual mandate is at the heart of resilience strategies, which in healthcare systems involve developing surge capacity to manage a sudden influx of patients. The paper aims to discuss these issues. Design/methodology/approach This paper relates insights from resilience research to the four "S" of surge capacity (staff, stuff, structures and systems) and proposes a framework based on complexity theory to better understand and assess resilience factors that enable the development of surge capacity in complex health systems. Findings Detailed and dynamic complexities manifest in different challenges during a crisis. Resilience factors are classified according to these types of complexity and along their temporal dimensions: proactive factors that improve preparedness to confront both usual and exceptional requirements, and passive factors that enable response to unexpected demands as they arise during a crisis. The framework is completed by further categorizing resilience factors according to their stabilizing or destabilizing impact, drawing on feedback processes described in complexity theory. Favorable order resilience factors create consistency and act as stabilizing forces in systems, while favorable disorder factors such as diversity and complementarity act as destabilizing forces. Originality/value The framework suggests a balanced and innovative process to integrate these factors in a pragmatic approach built around the fours "S" of surge capacity to increase health system resilience.

Representation of Solar Capacity Value in the ReEDS Capacity Expansion Model

Energy Technology Data Exchange (ETDEWEB)

Sigrin, B. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sullivan, P. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ibanez, E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Margolis, R. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-03-01

An important issue for electricity system operators is the estimation of renewables' capacity contributions to reliably meeting system demand, or their capacity value. While the capacity value of thermal generation can be estimated easily, assessment of wind and solar requires a more nuanced approach due to the resource variability. Reliability-based methods, particularly assessment of the Effective Load-Carrying Capacity, are considered to be the most robust and widely-accepted techniques for addressing this resource variability. This report compares estimates of solar PV capacity value by the Regional Energy Deployment System (ReEDS) capacity expansion model against two sources. The first comparison is against values published by utilities or other entities for known electrical systems at existing solar penetration levels. The second comparison is against a time-series ELCC simulation tool for high renewable penetration scenarios in the Western Interconnection. Results from the ReEDS model are found to compare well with both comparisons, despite being resolved at a super-hourly temporal resolution. Two results are relevant for other capacity-based models that use a super-hourly resolution to model solar capacity value. First, solar capacity value should not be parameterized as a static value, but must decay with increasing penetration. This is because -- for an afternoon-peaking system -- as solar penetration increases, the system's peak net load shifts to later in the day -- when solar output is lower. Second, long-term planning models should determine system adequacy requirements in each time period in order to approximate LOLP calculations. Within the ReEDS model we resolve these issues by using a capacity value estimate that varies by time-slice. Within each time period the net load and shadow price on ReEDS's planning reserve constraint signals the relative importance of additional firm capacity.

Efcient Computation of Buffer Capacities for Cyclo-Static Real-Time Systems with Back-Pressure

NARCIS (Netherlands)

Wiggers, M.H.; Bekooij, Marco; Bekooij, Marco Jan Gerrit; Jansen, P.G.; Smit, Gerardus Johannes Maria

2006-01-01

A key step in the design of cyclo-static real-time systems is the determination of buffer capacities. In our multiprocessor system, we apply back-pressure, which means that tasks wait for space in output buffers. Consequently buffer capacities affect the throughput. This requires the derivation of

Sensitivity of Multicarrier Two-Dimensional Spreading Schemes to Synchronization Errors

Directory of Open Access Journals (Sweden)

Geneviève Jourdain

2008-06-01

Full Text Available This paper presents the impact of synchronization errors on the performance of a downlink multicarrier two-dimensional spreading OFDM-CDMA system. This impact is measured by the degradation of the signal to interference and noise ratio (SINR obtained after despreading and equalization. The contribution of this paper is twofold. First, we use some properties of random matrix and free probability theories to derive a new expression of the SINR. This expression is then independent of the actual value of the spreading codes while still accounting for the orthogonality between codes. This model is validated by means of Monte Carlo simulations. Secondly, the model is exploited to derive the SINR degradation of OFDM-CDMA systems due to synchronization errors which include a timing error, a carrier frequency offset, and a sampling frequency offset. It is also exploited to compare the sensitivities of MC-CDMA and MC-DS-CDMA systems to these errors in a frequency selective channel. This work is carried out for zero-forcing and minimum mean square error equalizers.

Curtailment in a Highly Renewable Power System and Its Effect on Capacity Factors

Directory of Open Access Journals (Sweden)

Alexander Kies

2016-06-01

Full Text Available The capacity factor of a power plant is the ratio of generation over its potential generation. It is an important measure to describe wind and solar resources. However, the fluctuating nature of renewable power generation makes it difficult to integrate all generation at times. Whenever generation exceeds the load, curtailment or storage of energy is required. With increasing renewable shares in the power system, the level of curtailment will further increase. In this work, the influence of the curtailment on the capacity factors for a highly renewable German power system is studied. An effective capacity factor is introduced, and the implications for the distribution of renewable power plants are discussed. Three years of highly-resolved weather data were used to model wind and solar power generation. Together with historical load data and a transmission model, a possible future German power system was simulated. It is shown that effective capacity factors for unlimited transmission are strongly reduced by up to 60% (wind and 70% (photovoltaics and therefore of limited value in a highly renewable power system. Furthermore, the results demonstrate that wind power benefits more strongly from a reinforced transmission grid than photovoltaics (PV does.

Integration between terrestrial-based and satellite-based land mobile communications systems

Science.gov (United States)

Arcidiancono, Antonio

1990-01-01

A survey is given of several approaches to improving the performance and marketability of mobile satellite systems (MSS). The provision of voice/data services in the future regional European Land Mobile Satellite System (LMSS), network integration between the Digital Cellular Mobile System (GSM) and LMSS, the identification of critical areas for the implementation of integrated GSM/LMSS areas, space segment scenarios, LMSS for digital trunked private mobile radio (PMR) services, and code division multiple access (CDMA) techniques for a terrestrial/satellite system are covered.

Capacity of a dual enrollment system with two keys based on an SRAM-PUF

NARCIS (Netherlands)

Kusters, L.; Willems, F.M.J.

2018-01-01

We investigate the capacity of an SRAM-PUF based secrecy system that produces two secret keys during two consecutive enrollments. We determined the region of secret-key rates that are achievable and show that the total secret-key capacity is larger than for a single enrollment system. In our

On the Capacity of Underlay Cognitive Radio Systems

KAUST Repository

Sboui, Lokman

2013-05-05

Due to the scarcity of frequency spectrum in view of the evolution of wireless communication technologies, the cognitive radio (CR) concept has been introduced to efficiently exploit the available spectrum. This concept consists in introducing unlicensed/secondary users (SU’s) in existing networks to share the spectrum of licensed/primary users (PU’s) without harming primary communications hence the name of “spectrum sharing” technique. We study in this dissertation, the capacity and the achievable rate of the secondary user within various communication settings. We, firstly, investigate the capacity of the (SU’s) at low power regime for Nakagami fading channels and present closed form of the capacity under various types of interference and/or power constraints. We explicitly characterize two regimes where either the interference constraint or the power constraint dictates the optimal power profile. Our framework also highlights the effects of different fading parameters on the secondary link ergodic capacity. Interestingly, we show that the low power regime analysis provides a specific insight on the capacity behavior of CR that has not been reported by previous studies. Next, we determine the spectral efficiency gain of an uplink CR Multi-Input Multi- Output (MIMO) system in which the SU is allowed to share the spectrum with the PU using a specific precoding scheme to communicate with a common receiver. Applied to Rayleigh fading channels, we show, through numerical results, that our proposed scheme enhances considerably the cognitive achievable rate. For instance, in case of a perfect detection of the PU signal, after applying Successive Interference Cancellation (SIC), the CR rate remains non-zero for high Signal to Noise Ratio (SNR) which is usually impossible when we only use space alignment technique. In addition, we show that the rate gain is proportional to the allowed interference threshold by providing a fixed rate even in the high SNR range

Comparison of TCeMA and TDMA for Inter-Satellite Communications using OPNET Simulation

Science.gov (United States)

Hain, Regina Rosales; Ramanathan, Ram; Bergamo, Marcos; Wallett, Thomas M.

2003-01-01

A robust data link protocol, enabling unique physical and MAC layer technologies and sub-network level protocols, is needed in order to take advantage of the full potential of using both TDMA and CDMA in a satellite communication network. A novel MAC layer protocol, TDMA with CDMA-encoding multiple access (TCeMA) integrated with null-steered digital beam-forming spatial multiplexing, is investigated to support flexible spacecraft communications. Abstract models of the TCeMA and TDMA processes are developed in OPNFiT and a comparison of the performances of TCeMA and TDMA in a satellite network simulation are made. TCeMA provides the better connectivity and capacity with respect to TDMA for satellite communication traffic.

The Experimental Research on Seismic Capacity of the Envelope Systems with Steel Frame

Science.gov (United States)

Li, Jiuyang; Wang, Bingbing; Li, Hengxu

2017-09-01

In this paper, according to the present application situation of the external envelope systems steel frame in the severe cold region, the stuffed composite wall panels are improved, the flexible connection with the steel frame is designed, the reduced scale specimens are made, the seismic capacity test is made and some indexes of the envelope systems such as bearing capacity, energy consumption and ductility, etc. are compared, which provide reference for the development and application of the steel frame envelope systems.

A Decision Support System for Ship Maintenance Capacity Planning

NARCIS (Netherlands)

de Boer, R.; Schutten, Johannes M.J.; Zijm, Willem H.M.

1997-01-01

In this paper, the basic framework and algorithms of a decision support system are discussed, which enhance process and capacity planning at a large repair shop. The research is strongly motivated by experiences in a project carried out at a dockyard, which performs repair, overhaul and modification

Experimental study of a novel capacity control algorithm for a multi-evaporator air conditioning system

International Nuclear Information System (INIS)

Xu Xiangguo; Pan Yan; Deng Shiming; Xia Liang; Chan Mingyin

2013-01-01

The use of a multi-evaporator air conditioning (MEAC) system is advantageous in terms of installation convenience, high design flexibility, being easy to maintain and commission, better indoor thermal comfort control and higher energy efficiency. While MEAC units worth billions of dollars are sold worldwide, the detailed accounts on compressor capacity control and refrigeration flow distribution amongst evaporators remain unavailable in public domain, mainly due to commercial confidentiality. Limited control algorithms for MEAC systems have been developed based on system simulation, and no experimental-based capacity controller developments and their controllability tests may be identified in open literature. In the study reported in this paper, a novel capacity control algorithm, which imitated On–Off control of a single evaporator air conditioning (A/C) system in each indoor unit of a MEAC system by using variable speed compressor and electronic expansion valves (EEVs), was developed. Controllability tests under various settings for experimentally validating the novel capacity control algorithm were carried out and the control algorithm was further improved based on the experimental results. - Highlights: ► A capacity control algorithm for a multi-evaporator air conditioning system was developed. ► Experimental controllability tests under various settings were carried out. ► The control algorithm was further improved based on the experimental results.

Negative heat capacity at phase-separation in macroscopic systems

OpenAIRE

Gross, D. H. E.

2005-01-01

Systems with long-range as well with short-range interactions should necessarily have a convex entropy S(E) at proper phase transitions of first order, i.e. when a separation of phases occurs. Here the microcanonical heat capacity c(E)= -\\frac{(\\partial S/\\partial E)^2}{\\partial^2S/\\partial E^2} is negative. This should be observable even in macroscopic systems when energy fluctuations with the surrounding world can be sufficiently suppressed.

Optimal Capacity Proportion and Distribution Planning of Wind, Photovoltaic and Hydro Power in Bundled Transmission System

Science.gov (United States)

Ye, X.; Tang, Q.; Li, T.; Wang, Y. L.; Zhang, X.; Ye, S. Y.

2017-05-01

The wind, photovoltaic and hydro power bundled transmission system attends to become common in Northwest and Southwest of China. To make better use of the power complementary characteristic of different power sources, the installed capacity proportion of wind, photovoltaic and hydro power, and their capacity distribution for each integration node is a significant issue to be solved in power system planning stage. An optimal capacity proportion and capacity distribution model for wind, photovoltaic and hydro power bundled transmission system is proposed here, which considers the power out characteristic of power resources with different type and in different area based on real operation data. The transmission capacity limit of power grid is also considered in this paper. Simulation cases are tested referring to one real regional system in Southwest China for planning level year 2020. The results verify the effectiveness of the model in this paper.

On Performance of Linear Multiuser Detectors for Wireless Multimedia Applications

Science.gov (United States)

Agarwal, Rekha; Reddy, B. V. R.; Bindu, E.; Nayak, Pinki

In this paper, performance of different multi-rate schemes in DS-CDMA system is evaluated. The analysis of multirate linear multiuser detectors with multiprocessing gain is analyzed for synchronous Code Division Multiple Access (CDMA) systems. Variable data rate is achieved by varying the processing gain. Our conclusion is that bit error rate for multirate and single rate systems can be made same with a tradeoff with number of users in linear multiuser detectors.

Polarized Uniform Linear Array System: Beam Radiation Pattern, Beamforming Diversity Order, and Channel Capacity

Directory of Open Access Journals (Sweden)

Xin Su

2015-01-01

Full Text Available There have been many studies regarding antenna polarization; however, there have been few publications on the analysis of the channel capacity for polarized antenna systems using the beamforming technique. According to Chung et al., the channel capacity is determined by the density of scatterers and the transmission power, which is obtained based on the assumption that scatterers are uniformly distributed on a 3D spherical scattering model. However, it contradicts the practical scenario, where scatterers may not be uniformly distributed under outdoor environment, and lacks the consideration of fading channel gain. In this study, we derive the channel capacity of polarized uniform linear array (PULA systems using the beamforming technique in a practical scattering environment. The results show that, for PULA systems, the channel capacity, which is boosted by beamforming diversity, can be determined using the channel gain, beam radiation pattern, and beamforming diversity order (BDO, where the BDO is dependent on the antenna characteristics and array configurations.

Capacity of fully correlated MIMO system using character expansion of groups

Directory of Open Access Journals (Sweden)

Ejaz Khan

2005-09-01

Full Text Available It is well known that the use of antenna arrays at both sides of communication link can result in high channel capacities provided that the propagation medium is rich scattering. In most previous works presented on MIMO wireless structures, Rayleigh fading conditions were considered. In this work, the capacity of MIMO systems under fully correlated (i.e., correlations between rows and columns of channel matrix fading is considered. We use replica method and character expansions to calculate the capacity of correlated MIMO channel in closed form. In our calculations, it is assumed that the receiver has perfect channel state information (CSI but no such information is available at the transmitter.

It Systems Supporting the Management of Production Capacity

Science.gov (United States)

Milewska, Elżbieta

2017-03-01

The paper presents the problem of manufacturing process flexibility in view of a company's material and information flow stream management. The author of the article has described the functions of a production process control system and presented the characteristics of production capacity intensive and extensive reserves. The MRP II/ERP, MES and APS class IT tools supporting the process of production planning, organization and control have also been discussed.

IT SYSTEMS SUPPORTING THE MANAGEMENT OF PRODUCTION CAPACITY

OpenAIRE

Elżbieta MILEWSKA

2017-01-01

The paper presents the problem of manufacturing process flexibility in view of a company’s material and information flow stream management. The author of the article has described the functions of a production process control system and presented the characteristics of production capacity intensive and extensive reserves. The MRP II/ERP, MES and APS class IT tools supporting the process of production planning, organization and control have also been discussed.

Separate Poles Mode for Large-Capacity HVDC System

Science.gov (United States)

Zhu, Lin; Gao, Qin

2017-05-01

This paper proposes a novel connection mode, separate poles mode (SPM), for large-capacity HVDC systems. The proposed mode focuses on the core issues of HVDC connection in interconnected power grids and principally aims at increasing effective electric distance between poles, which helps to mitigate the interaction problems between AC system and DC system. Receiving end of bipolar HVDC has been divided into different inverter stations under the mode, and thus significantly alleviates difficulties in power transmission and consumption of receiving-end AC grids. By investigating the changes of multi-feed short-circuit ratio (MISCR), finding that HVDC with SPM shows critical impacts upon itself and other HVDC systems with conventional connection mode, which demonstrates that SPM can make balance between MISCR increase and short-circuit current limit.

Performance and capacity analysis of Poisson photon-counting based Iter-PIC OCDMA systems.

Science.gov (United States)

Li, Lingbin; Zhou, Xiaolin; Zhang, Rong; Zhang, Dingchen; Hanzo, Lajos

2013-11-04

In this paper, an iterative parallel interference cancellation (Iter-PIC) technique is developed for optical code-division multiple-access (OCDMA) systems relying on shot-noise limited Poisson photon-counting reception. The novel semi-analytical tool of extrinsic information transfer (EXIT) charts is used for analysing both the bit error rate (BER) performance as well as the channel capacity of these systems and the results are verified by Monte Carlo simulations. The proposed Iter-PIC OCDMA system is capable of achieving two orders of magnitude BER improvements and a 0.1 nats of capacity improvement over the conventional chip-level OCDMA systems at a coding rate of 1/10.

Impact of Cyclic Prefix length on OFDM system Capacity

DEFF Research Database (Denmark)

Rom, Christian; Sørensen, Troels Bundgaard; Mogensen, Preben Elgaard

2005-01-01

This paper is a study on the impact of the Cyclic Prefix (CP) length on the downlink Capacity in a base-band synchronized SISO-OFDM context. To measure this impact, the capacity, measured in bits per second per hertz, is chosen as quality parameter. The study shows how the lengthening of the CP......) the useful OFDM symbol duration, 2) the Signal to Noise Ratio (SNR) at the receiver and 3) the channel Power Delay Profile (PDP). Depending on the values of these parameters different optimum CP lengths are obtained. For a system using only one value of CP length we suggest an optimum value to be 4us...... for an OFDM symbol length of 40us and 6us for an OFDM symbol length of 80us....

Analisis Permasalahan Optimalisasi Voice CDMA 2000 1x Untuk Mengurangi Kegagalan Koneksi Studi Kasus Divisi Telkom Flexi Semarang

Directory of Open Access Journals (Sweden)

Alfin Hikmaturokhman

2011-11-01

Full Text Available Rapidly growing number of network providers in Code Division Multiple Access (CDMA, make service providers to further strength its network and optimization customer service and quality that will be given. In order to better serve our customer with the required network that has good performance. For that we need to be optimization in network, which can reduce the drop call and resource blocking and increasing call success. Network optimization is based on data drive test as for data analysis, including Call Setup Success Rate, Drop call Rate, Resource Blocking, Rx Power, Tx Power, Ec/Io, Forward FER, and Call Setup Time. In the measurement that have been done to the avarage value in accordance with Key Performance Indicator (KPI obtained Call Setup Success Rate (> 99%, Drop call Rate ( 99%, Drop call Rate (< 1%, Resource Blocking (< 1%, Rx Power (-99.9 dBm, Tx Power (-27.8 dBm, Ec/Io (-5.45 dB, Forward FER (2.45%, and Call Setup Time (4.902 seconds.

Wireless Emergency Alerts Commercial Mobile Service Provider (CMSP) Cybersecurity Guidelines

Science.gov (United States)

2016-06-16

Switching Centers (MSCs) in CDMA networks . The interface standard be- tween the MC and CDMA networks is the IS-824, IS-637 SMDPP.  Global System for... networks is 3GPP 23.041 CBS-BSC.  Universal Mobile Telecommunications System (UMTS) networks : A CBC function is collocated with a CMSP Gateway for message...agement 16. Does the carrier patch all systems and network devices as appropriate?    CMU/SEI-2016-SR-009 | SOFTWARE ENGINEERING INSTITUTE

IT SYSTEMS SUPPORTING THE MANAGEMENT OF PRODUCTION CAPACITY

Directory of Open Access Journals (Sweden)

Elżbieta MILEWSKA

2017-01-01

Full Text Available The paper presents the problem of manufacturing process flexibility in view of a company’s material and information flow stream management. The author of the article has described the functions of a production process control system and presented the characteristics of production capacity intensive and extensive reserves. The MRP II/ERP, MES and APS class IT tools supporting the process of production planning, organization and control have also been discussed.

Capacity Expansion and Reliability Evaluation on the Networks Flows with Continuous Stochastic Functional Capacity

Directory of Open Access Journals (Sweden)

F. Hamzezadeh

2014-01-01

Full Text Available In many systems such as computer network, fuel distribution, and transportation system, it is necessary to change the capacity of some arcs in order to increase maximum flow value from source s to sink t, while the capacity change incurs minimum cost. In real-time networks, some factors cause loss of arc’s flow. For example, in some flow distribution systems, evaporation, erosion or sediment in pipes waste the flow. Here we define a real capacity, or the so-called functional capacity, which is the operational capacity of an arc. In other words, the functional capacity of an arc equals the possible maximum flow that may pass through the arc. Increasing the functional arcs capacities incurs some cost. There is a certain resource available to cover the costs. First, we construct a mathematical model to minimize the total cost of expanding the functional capacities to the required levels. Then, we consider the loss of flow on each arc as a stochastic variable and compute the system reliability.

Research on the coding and decoding technology of the OCDMA system

Science.gov (United States)

Li, Ping; Wang, Yuru; Lan, Zhenping; Wang, Jinpeng; Zou, Nianyu

2015-12-01

Optical Code Division Multiplex Access, OCDMA, is a kind of new technology which is combined the wireless CDMA technology and the optical fiber communication technology together. The address coding technology in OCDMA system has been researched. Besides, the principle of the codec based on optical fiber delay line and non-coherent spectral domain encoding and decoding has been introduced and analysed, and the results was verified by experiment.

A Unified Framework of the Performance Evaluation of Optical Time-Wavelength Code-Division Multiple-Access Systems

Science.gov (United States)

Inaty, Elie

In this paper, we provide an analysis to the performance of optical time-wavelength code-division multiple-access (OTW-CDMA) network when the system is working above the nominal transmission rate limit imposed by the passive encoding-decoding operation. We address the problem of overlapping in such a system and how it can directly affect the bit error rate (BER). A unified mathematical framework is presented under the assumption of one coincidence sequences with non-repeating wavelengths. A closed form expression of the multiple access interference limited BER is provided as a function of different system parameters. Results show that the performance of OTW-CDMA system may be critically affected when working above the nominal limit; an event that may happen when the network operates at high transmission rate. In addition, the impact of the derived error probability on the performance of two newly proposed MAC protocols, the S-ALOHA and the R3T, is also investigated. It is shown that for low transmission rates, the S-ALOHA is better than the R3T; while the R3T is better at very high transmission rates. However, in general it is postulated that the R3T protocol suffers a higher delay mainly because of the presence of additional modes.

Electric distribution systems and embedded generation capacity

International Nuclear Information System (INIS)

Calderaro, V.; Galdi, V.; Piccolo, A.; Siano, P.

2006-01-01

The main policy issues of European States are sustainable energy supply promotion and liberalization of energy markets, which introduced market competition in electricity production and created support mechanisms to encourage renewable electricity production and consumption. As a result of liberalization, any generator, including small-scale and renewable energy based units, can sell electricity on the free market. In order to meet future sustainability targets, connection of a higher number of Distributed Generation (DG) units to the electrical power system is expected, requiring changes in the design and operation of distribution electricity systems, as well as changes in electricity network regulation. In order to assist distribution system operators in planning and managing DG connections and in maximizing DG penetration and renewable sources exploitation, this paper proposed a reconfiguration methodology based on a Genetic Algorithm (GA), that was tested on a 70-bus system with DG units. The simulation results confirmed that the methodology represents a suitable tool for distribution system operators when dealing with DG capacity expansion and power loss issues, providing information regarding the potential penetration network-wide and allowing maximum exploitation of renewable generation. 35 refs., 4 tabs., 6 figs

Review on the Evaluation System of Public Safety Carrying Capacity about Small Town Community

Institute of Scientific and Technical Information of China (English)

Ming; SUN; Tianyu; ZHU

2014-01-01

Recently,small town community public safety problem has been increasingly highlighted,but its research is short on public safety carrying capacity. Through the investigation and study of community public safety carrying capacity,this paper analyzes the problem of community public safety in our country,to construct index evaluation system of public safety carrying capacity in small town community. DEA method is used to evaluate public safety carrying capacity in small town community,to provide scientific basis for the design of support and standardization theory about small town community in public safety planning.

Absorptive capacity, technological innovation, and product life cycle: a system dynamics model.

Science.gov (United States)

Zou, Bo; Guo, Feng; Guo, Jinyu

2016-01-01

While past research has recognized the importance of the dynamic nature of absorptive capacity, there is limited knowledge on how to generate a fair and comprehensive analytical framework. Based on interviews with 24 Chinese firms, this study develops a system-dynamics model that incorporates an important feedback loop among absorptive capacity, technological innovation, and product life cycle (PLC). The simulation results reveal that (1) PLC affects the dynamic process of absorptive capacity; (2) the absorptive capacity of a firm peaks in the growth stage of PLC, and (3) the market demand at different PLC stages is the main driving force in firms' technological innovations. This study also explores a sensitivity simulation using the variables of (1) time spent in founding an external knowledge network, (2) research and development period, and (3) knowledge diversity. The sensitivity simulation results show that the changes of these three variables have a greater impact on absorptive capacity and technological innovation during growth and maturity stages than in the introduction and declining stages of PLC. We provide suggestions on how firms can adjust management policies to improve their absorptive capacity and technological innovation performance during different PLC stages.

Research on a novel DDC-based capacity controller for the direct-expansion variable-air-volume A/C system

Energy Technology Data Exchange (ETDEWEB)

Chen Wu, E-mail: chenwu73@263.ne [School of Marine Engineering, Jimei University, Xiamen, Fujian Province 361021 (China); Deng Shiming [Department of Building Services Engineering, The Hong Kong Polytechnic University, Kowloon (Hong Kong)

2010-01-15

A direct-expansion (DX) variable-air-volume (VAV) air-conditioning (A/C) system consists of a VAV air-distribution sub-system and a DX refrigeration plant. This paper reports in detail on a novel capacity controller developed for the DX VAV A/C system to regulate its compressor speed and hence its cooling capacity. The capacity controller consisted of both a numerical calculation algorithm (NCA), which was fundamentally based on the principle of energy balance using a number of real-time measured system's operating parameters, and a dead-band for decoupling the control actions from both the capacity controller and a conventional PI feedback controller for regulating the opening of an electronic expansion valve (EEV) in the refrigeration plant. To study the feasibility of the capacity controller, an experimental rig for the DX VAV A/C system having two conditioned spaces was built and experimental tests were carried out. The test results showed that using the capacity controller, the cooling capacity of the system's refrigeration plant can be accurately and continuously regulated and the supply air temperature well maintained at its desired value. The desirable independent zoning-control for space air temperatures can be successfully achieved by the DX VAV A/C system and the control performance for air temperatures in the conditioned space was highly satisfactory.

Research on a novel DDC-based capacity controller for the direct-expansion variable-air-volume A/C system

Energy Technology Data Exchange (ETDEWEB)

Chen, Wu [School of Marine Engineering, Jimei University, Xiamen, Fujian Province 361021 (China); Deng, Shiming [Department of Building Services Engineering, The Hong Kong Polytechnic University, Kowloon (China)

2010-01-15

A direct-expansion (DX) variable-air-volume (VAV) air-conditioning (A/C) system consists of a VAV air-distribution sub-system and a DX refrigeration plant. This paper reports in detail on a novel capacity controller developed for the DX VAV A/C system to regulate its compressor speed and hence its cooling capacity. The capacity controller consisted of both a numerical calculation algorithm (NCA), which was fundamentally based on the principle of energy balance using a number of real-time measured system's operating parameters, and a dead-band for decoupling the control actions from both the capacity controller and a conventional PI feedback controller for regulating the opening of an electronic expansion valve (EEV) in the refrigeration plant. To study the feasibility of the capacity controller, an experimental rig for the DX VAV A/C system having two conditioned spaces was built and experimental tests were carried out. The test results showed that using the capacity controller, the cooling capacity of the system's refrigeration plant can be accurately and continuously regulated and the supply air temperature well maintained at its desired value. The desirable independent zoning-control for space air temperatures can be successfully achieved by the DX VAV A/C system and the control performance for air temperatures in the conditioned space was highly satisfactory. (author)

Research on a novel DDC-based capacity controller for the direct-expansion variable-air-volume A/C system

International Nuclear Information System (INIS)

Chen Wu; Deng Shiming

2010-01-01

A direct-expansion (DX) variable-air-volume (VAV) air-conditioning (A/C) system consists of a VAV air-distribution sub-system and a DX refrigeration plant. This paper reports in detail on a novel capacity controller developed for the DX VAV A/C system to regulate its compressor speed and hence its cooling capacity. The capacity controller consisted of both a numerical calculation algorithm (NCA), which was fundamentally based on the principle of energy balance using a number of real-time measured system's operating parameters, and a dead-band for decoupling the control actions from both the capacity controller and a conventional PI feedback controller for regulating the opening of an electronic expansion valve (EEV) in the refrigeration plant. To study the feasibility of the capacity controller, an experimental rig for the DX VAV A/C system having two conditioned spaces was built and experimental tests were carried out. The test results showed that using the capacity controller, the cooling capacity of the system's refrigeration plant can be accurately and continuously regulated and the supply air temperature well maintained at its desired value. The desirable independent zoning-control for space air temperatures can be successfully achieved by the DX VAV A/C system and the control performance for air temperatures in the conditioned space was highly satisfactory.

Achievable capacity of a spectrum sharing system over hyper fading channels

KAUST Repository

Ekin, Sabit; Yilmaz, Ferkan; Ç elebi, Hasari Burak; Qaraqe, Khalid A.; Alouini, Mohamed-Slim; Serpedin, Erchin

2009-01-01

Cognitive radio with spectrum sharing feature is a promising technique to address the spectrum under-utilization problem in dynamically changing environments. In this paper, achievable capacity gain of spectrum sharing systems over dynamic fading

On the BER and capacity analysis of MIMO MRC systems with channel estimation error

KAUST Repository

Yang, Liang

2011-10-01

In this paper, we investigate the effect of channel estimation error on the capacity and bit-error rate (BER) of a multiple-input multiple-output (MIMO) transmit maximal ratio transmission (MRT) and receive maximal ratio combining (MRC) systems over uncorrelated Rayleigh fading channels. We first derive the ergodic (average) capacity expressions for such systems when power adaptation is applied at the transmitter. The exact capacity expression for the uniform power allocation case is also presented. Furthermore, to investigate the diversity order of MIMO MRT-MRC scheme, we derive the BER performance under a uniform power allocation policy. We also present an asymptotic BER performance analysis for the MIMO MRT-MRC system with multiuser diversity. The numerical results are given to illustrate the sensitivity of the main performance to the channel estimation error and the tightness of the approximate cutoff value. © 2011 IEEE.

Estimation of Parameters Obtained by Electrochemical Impedance Spectroscopy on Systems Containing High Capacities

Directory of Open Access Journals (Sweden)

Mirjana Rajčić Vujasinović

2009-09-01

Full Text Available Electrochemical systems with high capacities demand devices for electrochemical impedance spectroscopy (EIS with ultra-low frequencies (in order of mHz, that are almost impossible to accomplish with analogue techniques, but this becomes possible by using a computer technique and accompanying digital equipment. Recently, an original software and hardware for electrochemical measurements, intended for electrochemical systems exhibiting high capacities, such as supercapacitors, has been developed. One of the included methods is EIS. In this paper, the method of calculation of circuit parameters from an EIS curve is described. The results of testing on a physical model of an electrochemical system, constructed of known elements (including a 1.6 F capacitor in a defined arrangement, proved the validity of the system and the method.

Bulk power system performance issues affecting utility peaking capacity additions

Energy Technology Data Exchange (ETDEWEB)

Garrity, T.F. [GE Power Sytems, Schenectady, NY (United States)

1994-12-31

This paper presents a discussion of transmission system constraints and problems that affect the siting and rating of peaking capacity additions. Techniques for addressing and modifying these concerns are presented. Particular attention is paid to techniques that have been successfully used by utilities to improve power transfer and system loadability, while avoiding the construction of additional transmission lines. Proven techniques for dealing with thermal, short-circuit level and stability issues are presented.

Enhancing Adaptive Capacity in Food Systems: Learning at Farmers' Markets in Sweden

Directory of Open Access Journals (Sweden)

Rebecka Milestad

2010-09-01

Full Text Available This article examines how local food systems in the form of farmers' markets can enhance adaptive capacity and build social-ecological resilience. It does this by exploring the learning potential among farmers and customers. Learning can enable actors to adapt successfully and thus build adaptive capacity. Three forms of learning are investigated: instrumental, communicative, and emancipatory. These forms of learning constitute the foundation for lasting changes of behaviors. Local food systems are characterized by close links and opportunities for face-to-face interactions between consumers and producers of food, and are also institutions where farmers and customers can express and act upon their ethical values concerning food. However, local food systems are still a marginal phenomenon and cannot be accessed by all consumers. Interviews were held with customers and farmers, and the interactions between farmers and customers were observed at two farmers' markets in Sweden. Customers and farmers were found to learn and adapt to each other due to the opportunities offered by the farmers' markets. We found that farmers and customers learned in the instrumental and communicative domains, but could not confirm emancipatory learning. We concluded that the feedback between customers and farmers offers the potential for learning, which in turn contributes to adaptive capacity. This can be a driving force for building resilience in the food system.

Institutional capacity for health systems research in East and Central African schools of public health: experiences with a capacity assessment tool.

Science.gov (United States)

Jessani, Nasreen; Lewy, Daniela; Ekirapa-Kiracho, Elizabeth; Bennett, Sara

2014-06-02

Despite significant investments in health systems research (HSR) capacity development, there is a dearth of information regarding how to assess HSR capacity. An alliance of schools of public health (SPHs) in East and Central Africa developed a tool for the self-assessment of HSR capacity with the aim of producing institutional capacity development plans. Between June and November 2011, seven SPHs across the Democratic Republic of Congo, Ethiopia, Kenya, Rwanda, Tanzania, and Uganda implemented this co-created tool. The objectives of the institutional assessments were to assess existing capacities for HSR and to develop capacity development plans to address prioritized gaps. A mixed-method approach was employed consisting of document analysis, self-assessment questionnaires, in-depth interviews, and institutional dialogues aimed at capturing individual perceptions of institutional leadership, collective HSR skills, knowledge translation, and faculty incentives to engage in HSR. Implementation strategies for the capacity assessment varied across the SPHs. This paper reports findings from semi-structured interviews with focal persons from each SPH, to reflect on the process used at each SPH to execute the institutional assessments as well as the perceived strengths and weaknesses of the assessment process. The assessment tool was robust enough to be utilized in its entirety across all seven SPHs resulting in a thorough HSR capacity assessment and a capacity development plan for each SPH. Successful implementation of the capacity assessment exercises depended on four factors: (i) support from senior leadership and collaborators, (ii) a common understanding of HSR, (iii) adequate human and financial resources for the exercise, and (iv) availability of data. Methods of extracting information from the results of the assessments, however, were tailored to the unique objectives of each SPH. This institutional HSR capacity assessment tool and the process for its utilization

Near-Capacity Coding for Discrete Multitone Systems with Impulse Noise

Directory of Open Access Journals (Sweden)

Kschischang Frank R

2006-01-01

Full Text Available We consider the design of near-capacity-achieving error-correcting codes for a discrete multitone (DMT system in the presence of both additive white Gaussian noise and impulse noise. Impulse noise is one of the main channel impairments for digital subscriber lines (DSL. One way to combat impulse noise is to detect the presence of the impulses and to declare an erasure when an impulse occurs. In this paper, we propose a coding system based on low-density parity-check (LDPC codes and bit-interleaved coded modulation that is capable of taking advantage of the knowledge of erasures. We show that by carefully choosing the degree distribution of an irregular LDPC code, both the additive noise and the erasures can be handled by a single code, thus eliminating the need for an outer code. Such a system can perform close to the capacity of the channel and for the same redundancy is significantly more immune to the impulse noise than existing methods based on an outer Reed-Solomon (RS code. The proposed method has a lower implementation complexity than the concatenated coding approach.

Microwave photonics technologies supporting high capacity and flexible wireless communications systems

DEFF Research Database (Denmark)

Lu, Xiaofeng; Tatarczak, Anna; Rommel, Simon

2015-01-01

Emerging 5G wireless systems require technologies for increased capacity, guarantee robustness, low latency and flexibility. We review a number of approaches to provide the above based on microwave photonics and hybrid optical fiber-wireless communication techniques....

Building Capacity in Health Systems and Policy Analysis in sub ...

International Development Research Centre (IDRC) Digital Library (Canada)

Building Capacity in Health Systems and Policy Analysis in sub-Saharan Africa. Since 2005, the Bill and Melinda Gates Foundation has been financing the master's program in health and population at the Institut supérieure des sciences de la population (ISSP), Université de Ouagadougou, Burkina Faso. However, after ...

Research on Overconfidence in Decision-Making for the Capacity Recovery of Damaged Power Systems

Directory of Open Access Journals (Sweden)

Xing Bao

2014-01-01

Full Text Available This paper studies the influence of two types of overconfident behavior, overestimation and overprecision, on decision of capacity recovery when power system’s critical capacity is seriously damaged. A newsvendor model is used to prove that increasing regulatory punishment for electricity shortage and providing subsidy for capacity recovery are conducive measures to calibrate insufficient service level caused by an overconfident manager. The research also finds that the manager’s overprecision behavior both negatively and positively influences the decision of capacity recovery, and a calibration method could motivate manager to recover more capacity by tuning up the ratio of punishment and subsidy. However, the effectiveness of the calibration mentioned above is inevitably weakened due to the less capacity recovery given by an overestimated manager. This research also indicates that the manager should pay close attention to the random disturbance whose distribution peak is left skewed, and correspondingly more capacity recovery should be given to improve the service level of power system during the disruption.

Understanding Absorptive Capacities is an "Innovation Systems" Context

DEFF Research Database (Denmark)

Narula, Rajneesh

2004-01-01

This paper seeks to broaden our understanding of the concept underlying absorptive capacity atthe macro -level, paying particular attention to the growth and development perspectives. Weprovide definitions of absorptive and technological capacity, external technology flows,productivity growth....... We also undertake to explain how the nature ofabsorptive capacity changes with stages of economic development, and the importance of thedifferent aspects of absorptive capability at different stages. The relationship is not a linear one:the benefits that accrue from marginal increases in absorptive...... capability change over time.Finally, we provide a tentative and preliminary conceptual argument of how the different stagesof absorptive capacity are related to productivity growth, economic growth and employmentcreation.Key words: New economy, absorptive capacity, knowledge...

Preliminary Findings of the South Africa Power System Capacity Expansion and Operational Modelling Study: Preprint

Energy Technology Data Exchange (ETDEWEB)

Reber, Timothy J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Chartan, Erol Kevin [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Brinkman, Gregory L [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2018-01-01

Wind and solar power contract prices have recently become cheaper than many conventional new-build alternatives in South Africa and trends suggest a continued increase in the share of variable renewable energy (vRE) on South Africa's power system with coal technology seeing the greatest reduction in capacity, see 'Figure 6: Percentage share by Installed Capacity (MW)' in [1]. Hence it is essential to perform a state-of-the-art grid integration study examining the effects of these high penetrations of vRE on South Africa's power system. Under the 21st Century Power Partnership (21CPP), funded by the U.S. Department of Energy, the National Renewable Energy Laboratory (NREL) has significantly augmented existing models of the South African power system to investigate future vRE scenarios. NREL, in collaboration with Eskom's Planning Department, further developed, tested and ran a combined capacity expansion and operational model of the South African power system including spatially disaggregated detail and geographical representation of system resources. New software to visualize and interpret modelling outputs has been developed, and scenario analysis of stepwise vRE build targets reveals new insight into associated planning and operational impacts and costs. The model, built using PLEXOS, is split into two components, firstly a capacity expansion model and secondly a unit commitment and economic dispatch model. The capacity expansion model optimizes new generation decisions to achieve the lowest cost, with a full understanding of capital cost and an approximated understanding of operational costs. The operational model has a greater set of detailed operational constraints and is run at daily resolutions. Both are run from 2017 through 2050. This investigation suggests that running both models in tandem may be the most effective means to plan the least cost South African power system as build plans seen to be more expensive than optimal by the

Developing nursing capacity for health systems and services research in Cuba, 2008-2011.

Science.gov (United States)

Martínez, Nelcy

2012-07-01

Health systems and services research by nursing personnel could inform decision-making and nursing care, providing evidence concerning quality of and patient satisfaction. Such studies are rather uncommon in Cuban research institutes, where clinical research predominates. Assess the results of a strategy implemented between 2008 and 2011 to develop nursing capacity for health systems and services research in 14 national research institutes based in Havana. The study comprised four stages: description of approaches to health systems and services research by nurses worldwide and in Cuba; analysis of current capacities for such research in Cuba; intervention design and implementation; and evaluation. Various techniques were used including: literature review, bibliometric analysis, questionnaire survey, consultation with experts, focus groups, and workshops for participant orientation and design and followup of research projects. Qualitative information reduction and quantitative information summary methods were used. Initially, 32 nursing managers participated; a further 105 nurses from the institutes were involved in research teams formed during intervention implementation. Of all published nursing research articles retrieved, 8.9% (185 of 2081) concerned health systems and services research, of which 26.5% (49 of 185) dealt with quality assessment. At baseline, 75% of Cuban nurses surveyed had poor knowledge of health systems and services research. Orientation, design and followup workshops for all institute teams developed individual and institutional capacity for health systems and services research. Post-intervention, 84.7% (27) of nurses reached good knowledge and 14.3% (5) fair; institutional research teams were formed and maintained in 9 institutes, and 13 projects designed and implemented (11 institutional, 2 addressing ministerial-level priorities) to research nursing issues at selected centers. A systematic strategy to build nursing capacity for health

On finite capacity queueing systems with a general vacation policy

Directory of Open Access Journals (Sweden)

Jacqueline Loris-Teghem

2000-01-01

Full Text Available We consider a Poisson arrival queueing system with finite capacity and a general vacation policy as described in Loris-Teghem [Queueing Systems 3 (1988, 41-52]. From our previous results regarding the stationary queue length distributions immediately after a departure and at an arbitrary epoch, we derive a relation between both distributions which extends a result given in Frey and Takahashi [Operations Research Letters 21 (1997, 95-100] for the particular case of an exhaustive service multiple vacation policy.

Lithographically-Scribed Planar Holographic Optical CDMA Devices and Systems

National Research Council Canada - National Science Library

Mossberg, Thomas

2007-01-01

.... The present Phase II effort has harnessed new fabrication tools to perfect disruptive HBR-based multiplexer products for DoD avionics, optical communications systems computer data communications and local area networks...

Effect of cell phone radiofrequency radiation on body temperature in rodents: Pilot studies of the National Toxicology Program's reverberation chamber exposure system.

Science.gov (United States)

Wyde, Michael E; Horn, Thomas L; Capstick, Myles H; Ladbury, John M; Koepke, Galen; Wilson, Perry F; Kissling, Grace E; Stout, Matthew D; Kuster, Niels; Melnick, Ronald L; Gauger, James; Bucher, John R; McCormick, David L

2018-04-01

Radiofrequency radiation (RFR) causes heating, which can lead to detrimental biological effects. To characterize the effects of RFR exposure on body temperature in relation to animal size and pregnancy, a series of short-term toxicity studies was conducted in a unique RFR exposure system. Young and old B6C3F1 mice and young, old, and pregnant Harlan Sprague-Dawley rats were exposed to Global System for Mobile Communication (GSM) or Code Division Multiple Access (CDMA) RFR (rats = 900 MHz, mice = 1,900 MHz) at specific absorption rates (SARs) up to 12 W/kg for approximately 9 h a day for 5 days. In general, fewer and less severe increases in body temperature were observed in young than in older rats. SAR-dependent increases in subcutaneous body temperatures were observed at exposures ≥6 W/kg in both modulations. Exposures of  ≥10 W/kg GSM or CDMA RFR induced excessive increases in body temperature, leading to mortality. There was also a significant increase in the number of resorptions in pregnant rats at 12 W/kg GSM RFR. In mice, only sporadic increases in body temperature were observed regardless of sex or age when exposed to GSM or CDMA RFR up to 12 W/kg. These results identified SARs at which measurable RFR-mediated thermal effects occur, and were used in the selection of exposures for subsequent toxicology and carcinogenicity studies. Bioelectromagnetics. 39:190-199, 2018. © 2018 The Authors. Bioelectromagnetics Published by Wiley Periodicals, Inc. © 2018 The Authors. Bioelectromagnetics Published by Wiley Periodicals, Inc.

Model predictive control-based scheduler for repetitive discrete event systems with capacity constraints

Directory of Open Access Journals (Sweden)

Hiroyuki Goto

2013-07-01

Full Text Available A model predictive control-based scheduler for a class of discrete event systems is designed and developed. We focus on repetitive, multiple-input, multiple-output, and directed acyclic graph structured systems on which capacity constraints can be imposed. The target system’s behaviour is described by linear equations in max-plus algebra, referred to as state-space representation. Assuming that the system’s performance can be improved by paying additional cost, we adjust the system parameters and determine control inputs for which the reference output signals can be observed. The main contribution of this research is twofold, 1: For systems with capacity constraints, we derived an output prediction equation as functions of adjustable variables in a recursive form, 2: Regarding the construct for the system’s representation, we improved the structure to accomplish general operations which are essential for adjusting the system parameters. The result of numerical simulation in a later section demonstrates the effectiveness of the developed controller.

Performance Analysis of Capacity of MIMO Systems under Multiuser Interference Based on Worst-Case Noise Behavior

Directory of Open Access Journals (Sweden)

Jorswieck E. A.

2004-01-01

Full Text Available The capacity of a cellular multiuser MIMO system depends on various parameters, for example, the system structure, the transmit and receive strategies, the channel state information at the transmitter and the receiver, and the channel properties. Recently, the main focus of research was on single-user MIMO systems, their channel capacity, and their error performance with space-time coding. In general, the capacity of a cellular multiuser MIMO system is limited by additive white Gaussian noise, intracell interference from other users within the cell, and intercell interference from users outside the considered cell. We study one point-to-point link, on which interference acts. The interference models the different system scenarios and various parameters. Therefore, we consider three scenarios in which the noise is subject to different constraints. A general trace constraint is used in the first scenario. The noise covariance matrix eigenvalues are kept fixed in the second scenario, and in the third scenario the entries on the diagonal of the noise covariance matrix are kept fixed. We assume that the receiver as well as the transmitter have perfect channel state information. We solve the corresponding minimax programming problems and characterize the worst-case noise and the optimal transmit strategy. In all scenarios, the achievable capacity of the MIMO system with worst-case noise is equal to the capacity of some MIMO system in which either the channels are orthogonal or the transmit antennas are not allowed to cooperate or in which no channel state information is available at the transmitter. Furthermore, the minimax expressions fulfill a saddle point property. All theoretical results are illustrated by examples and numerical simulations.

Considerations for transient stability, fault capacity and power flow study of offsite power system

Energy Technology Data Exchange (ETDEWEB)

Shin, M C; Kim, C W; Gwon, M H; Park, C W; Lee, K W; Kim, H M; Lee, G Y; Joe, P H [Sungkyunkwan Univ., Seoul (Korea, Republic of)

1994-04-15

By study of power flow calculation, fault capacity calculation and stability analysis according to connection of two units YGN 3 and 4 to KEPCO power system, we have conclusions as follows. As the result of power flow calculation, at peak load, the voltage change of each bus is very small when YGN 3 and 4 is connected with KEPCO power system. At base load, installation of phase modifing equipment is necessary in Seoul, Kyungki province where load is concentrated because bus voltage rises by increasing of charge capacity caused installation of underground cables. As the result of fault capacity calculation, fault capacity is increased because fault current increases when two units YGN 3 and 4 is connected with KEPCO power system. But it is enough to operate with presenting circuits breaker rated capacity. Transient stability studies have been conducted on the YK N/P generators 3 and 4 using a digital computer program. Three phase short faults have been simulated at the YK N/P 345[KV] bus with the resulting outage of transmission circuits. Several fault clearing times are applied: 6 cycles, 12 cycles, 15 cycles. The study results demonstrate that the transient stability of YK N/P is adequate to maintain stable for three phase short faults cleared within 12 cycles. The study results also demonstrate that the transient stability of YK N/P is stable for machine removals except 4-machine removal. In addition, the study shows that the transient stability analysis is implemented for the case of load.

On the average capacity and bit error probability of wireless communication systems

KAUST Repository

Yilmaz, Ferkan; Alouini, Mohamed-Slim

2011-01-01

Analysis of the average binary error probabilities and average capacity of wireless communications systems over generalized fading channels have been considered separately in the past. This paper introduces a novel moment generating function

Simplified inelastic seismic response analysis of piping system using improved capacity spectrum method

International Nuclear Information System (INIS)

Iijima, Tadashi

2005-01-01

We applied improved capacity spectrum method (ICSM) to a piping system with an asymmetric load-deformation relationship in a piping elbow. The capacity spectrum method can predict an inelastic response by balancing the structural capacity obtained from the load-deformation relationship with the seismic demand defined by an acceleration-displacement response spectrum. The ICSM employs (1) effective damping ratio and period that are based on a statistical methodology, (2) practical procedures necessary to obtain a balance between the structural capacity and the seismic demand. The effective damping ratio and period are defined so as to maximize the probability that predicted response errors lie inside the -10 to 20% range. However, without taking asymmetry into consideration the displacement calculated by using the load-deformation relationship on the stiffer side was 39% larger than that of a time history analysis by a direct integral method. On the other hand, when asymmetry was taken into account, the calculated displacement was only 14% larger than that of a time history analysis. Thus, we verified that the ICSM could predict the inelastic response with errors lying within the -10 to 20% range, by taking into account the asymmetric load-deformation relationship of the piping system. (author)

Measuring the Capacity and Transaction Time of Cash and Electronic Toll Collection Systems

Directory of Open Access Journals (Sweden)

Rudy Hermawan Karsaman

2014-07-01

Full Text Available A long queue can occur at tollgates due to the amount of transaction time required to perform ticket payment and toll fee collection. This problem can be addressed by the use of an electronic toll collection (ETC system. A case study conducted on the Jakarta Intra Urban, Cikupa-Merak, and Cawang Pluit Toll Roads suggests that the queueing at the tollgates when modelled followed a Poisson distribution. The average cash transaction time was approximately 5 to 6 seconds, while the ETC transaction time was only 4 seconds. Furthermore, the capacity of the cash system gate was 550 to 620 vehicles/hour (which is above the minimum service standard of 450 vehicles/hour,whereas the electronic gate capacity was 770 to 870 vehicles/hour. This study demonstrates that the ETC system is more effective than the cash system in terms of reducing the number of queueing vehicles.

Integrated capacity and inventory management with capacity acquisition lead times

NARCIS (Netherlands)

Mincsovics, G.Z.; Tan, T.; Alp, O.

2009-01-01

We model a make-to-stock production system that utilizes permanent and contingent capacity to meet non-stationary stochastic demand, where a constant lead time is associated with the acquisition of contingent capacity. We determine the structure of the optimal solution concerning both the

On the Asymptotic Capacity of Dual-Aperture FSO Systems with a Generalized Pointing Error Model

KAUST Repository

Al-Quwaiee, Hessa

2016-06-28

Free-space optical (FSO) communication systems are negatively affected by two physical phenomenon, namely, scintillation due to atmospheric turbulence and pointing errors. To quantify the effect of these two factors on FSO system performance, we need an effective mathematical model for them. In this paper, we propose and study a generalized pointing error model based on the Beckmann distribution. We then derive a generic expression of the asymptotic capacity of FSO systems under the joint impact of turbulence and generalized pointing error impairments. Finally, the asymptotic channel capacity formula are extended to quantify the FSO systems performance with selection and switched-and-stay diversity.

Perbandingan Kinerja Deteksi Multiuser Linier Dan Deteksi Multiuser Dengan Jaringan Syaraf Tiruan Pada Sistem DS-CDMA

Directory of Open Access Journals (Sweden)

Popy Maria

2016-03-01

Full Text Available Beberapa hal yang dapat menurunkan kapasitas dan kualitas sinyal informasi yang diterima pada sistem DS-CDMA (Direct Sequence Code Division Multiple Access adalah interferensi, noise dan efek near-far. Pada umumnya efek near-far diatasi dengan menggunakan power control. Namun demikian power control tidak dapat mengatasi interferensi yang disebabkan oleh user lain pada kanal yang sama atau yang lebih dikenal dengan MAI (Multiple Access Interference. Pendekatan lain yang digunakan untuk mengatasi hal ini adalah dengan deteksi multiuser (MUD. Pada tugas akhir ini akan dibandingkan kinerja dari MUD linier yang terdiri dari decorrelating dan MMSE dengan MUD yang menggunakan jaringan syaraf tiruan (JST dan mengacu pada deteksi konvensional. Jaringan syaraf tiruan ini menggunakan algoritma propagasi balik. Deteksi multiuser ini diaplikasikan pada  output deteksi konvensional. Kinerja dari masing-masing detektor dilihat dari BER sebagai fungsi nilai SNR  atau jumlah user pada kanal AWGN dan Rayleigh fading. Hasil simulasi pada  kanal AWGN, menunjukkan bahwa MUD dengan JST mempunyai kinerja yang lebih baik. Untuk target BER 10-3 pada kanal  AWGN, MUD decorrelating mencapainya pada SNR 6.3 dB, MUD MMSE pada SNR 5.97 dB, dan MUD dengan JST pada SNR 5.89 dB sedangkan pada kanal Rayleigh, MUD decorrelating mencapainya pada SNR 11.74 dB, MUD MMSE pada SNR 10.91 dB, dan MUD dengan JST pada SNR 10.31 dB

Performance Analysis of Spectral Amplitude Coding Based OCDMA System with Gain and Splitter Mismatch

Science.gov (United States)

Umrani, Fahim A.; Umrani, A. Waheed; Umrani, Naveed A.; Memon, Kehkashan A.; Kalwar, Imtiaz Hussain

2013-09-01

This paper presents the practical analysis of the optical code-division multiple-access (O-CDMA) systems based on perfect difference codes. The work carried out use SNR criterion to select the optimal value of avalanche photodiodes (APD) gain and shows how the mismatch in the splitters and gains of the APD used in the transmitters and receivers of network can degrade the BER performance of the system. The investigations also reveal that higher APD gains are not suitable for such systems even at higher powers. The system performance, with consideration of shot noise, thermal noise, bulk and surface leakage currents is also investigated.

Research on Improved VSG Control Algorithm Based on Capacity-Limited Energy Storage System

Directory of Open Access Journals (Sweden)

Yanfeng Ma

2018-03-01

Full Text Available A large scale of renewable energy employing grid connected electronic inverters fail to contribute inertia or damping to power systems, and, therefore, may bring negative effects to the stability of power system. As a solution, an advanced Virtual Synchronous Generator (VSG control technology based on Hamilton approach is introduced in this paper firstly to support the frequency and enhance the suitability and robustness of the system. The charge and discharge process of power storage devices forms the virtual inertia and damping of VSG, and, therefore, limits on storage capacity may change the coefficients of VSG. To provide a method in keeping system output in an acceptable level with the capacity restriction in a transient period, an energy control algorithm is designed for VSG adaptive control. Finally, simulations are conducted in DIgSILENT to demonstrate the correctness of the algorithm. The demonstration shows: (1 the proposed control model aims at better system robustness and stability; and (2 the model performs in the environment closer to practical engineering by fitting the operation state of storage system.

Optimal power allocation and joint source-channel coding for wireless DS-CDMA visual sensor networks

Science.gov (United States)

Pandremmenou, Katerina; Kondi, Lisimachos P.; Parsopoulos, Konstantinos E.

2011-01-01

In this paper, we propose a scheme for the optimal allocation of power, source coding rate, and channel coding rate for each of the nodes of a wireless Direct Sequence Code Division Multiple Access (DS-CDMA) visual sensor network. The optimization is quality-driven, i.e. the received quality of the video that is transmitted by the nodes is optimized. The scheme takes into account the fact that the sensor nodes may be imaging scenes with varying levels of motion. Nodes that image low-motion scenes will require a lower source coding rate, so they will be able to allocate a greater portion of the total available bit rate to channel coding. Stronger channel coding will mean that such nodes will be able to transmit at lower power. This will both increase battery life and reduce interference to other nodes. Two optimization criteria are considered. One that minimizes the average video distortion of the nodes and one that minimizes the maximum distortion among the nodes. The transmission powers are allowed to take continuous values, whereas the source and channel coding rates can assume only discrete values. Thus, the resulting optimization problem lies in the field of mixed-integer optimization tasks and is solved using Particle Swarm Optimization. Our experimental results show the importance of considering the characteristics of the video sequences when determining the transmission power, source coding rate and channel coding rate for the nodes of the visual sensor network.

Concise Approach for Determining the Optimal Annual Capacity Shortage Percentage using Techno-Economic Feasibility Parameters of PV Power System

Science.gov (United States)

Alghoul, M. A.; Ali, Amer; Kannanaikal, F. V.; Amin, N.; Sopian, K.

2017-11-01

PV power systems have been commercially available and widely used for decades. The performance of a reliable PV system that fulfils the expectations requires correct input data and careful design. Inaccurate input data of the techno-economic feasibility would affect the size, cost aspects, stability and performance of PV power system on the long run. The annual capacity shortage is one of the main input data that should be selected with careful attention. The aim of this study is to reveal the effect of different annual capacity shortages on the techno-economic feasibility parameters and determining the optimal value for Baghdad city location using HOMER simulation tool. Six values of annual capacity shortage percentages (0%, 1%, 2%, 3%, 4%, and 5%), and wide daily load profile range (10 kWh - 100 kWh) are implemented. The optimal annual capacity shortage is the value that always "wins" when each techno-economic feasibility parameter is at its optimal/ reasonable criteria. The results showed that the optimal annual capacity shortage that reduces significantly the cost of PV power system while keeping the PV system with reasonable technical feasibility is 3%. This capacity shortage value can be carried as a reference value in future works for Baghdad city location. Using this approach of analysis at other locations, annual capacity shortage can be always offered as a reference value for those locations.

The Use of National Systems of Innovation Models to Develop Indicators of Innovation and Technological Capacity

OpenAIRE

Holbrook, J. A.

1997-01-01

This paper addresses various models that can be used to assess indicators of innovation and technical capacity. It stresses the importance of looking at the national system of innovation (NSI) to gain a complete understanding of industry capacity.

On the ergodic capacity of legacy systems in the presence of next generation interference

KAUST Repository

Mahmood, Nurul Huda

2011-11-01

Next generation wireless systems facilitating better utilization of the scarce radio spectrum have emerged as a response to inefficient rigid spectrum assignment policies. These are comprised of intelligent radio nodes that opportunistically operate in the radio spectrum of existing legacy systems; yet unwanted interference at the legacy receivers is unavoidable. In order to design efficient next generation systems and to minimize their harmful consequences, it is necessary to realize their impact on the performance of legacy systems. In this work, a generalized framework for the ergodic capacity analysis of such legacy systems in the presence of interference from next generation systems is presented. The analysis is built around a model developed for the statistical representation of the interference at the legacy receivers, which is then used to evaluate the ergodic capacity of the legacy system. Moreover, this analysis is not limited to the context of legacy systems, and is in fact applicaple to any interference limited system. Findings of analytical performance analyses are confirmed through selected computer-based Monte-Carlo simulations. © 2011 IEEE.

SOLUTION OF THE PROBLEM OF INCREASING THE CAPACITY OF POWER SYSTEM BY USING THE MATLAB MODELING

International Nuclear Information System (INIS)

Mshvidobadze, T.

2008-01-01

A mathematical model of power system was constructed. It included eight types of electric power plants essential for covering a deficit and bringing the generating capacities of the power system to the level which would provide its normal operation. The restrictions were stated in terms of inequalities, the efficiency function was chosen and the corresponding problem was solved by using the Matlab system. The obtained values of variables represented the values of generated capacities of appropriate power plants providing the minimum value of the efficiency function. (author)

Phosphorus Sorption Capacity of Gray Forest Soil as Dependent on Fertilization System

Science.gov (United States)

Rogova, O. B.; Kolobova, N. A.; Ivanov, A. L.

2018-05-01

In this paper, the results of the study of changes in the phosphorus sorption capacity of gray forest soils of Vladimir opolie under the impact of different fertilization systems are discussed. The quantitative parameters of the potential buffer capacity of soils for phosphorus (PBCP) and Langmuir sorption isotherms have been calculated. It is shown that the application of organic fertilizers results in a stronger decrease in PBCP than the application of mineral fertilizers. The portion of phosphorus of mineral compounds considerably increases, and the high content of available phosphates is maintained. In the variants with application of mineral phosphorus in combination with manure, the portions of organic and mineral phosphorus are at the level typical of unfertilized soils. The energy of phosphate bonds with the soil is minimal upon the application of a double rate of mineral phosphorus at the maximum capacity in relation to phosphate ions.

A Novel Method for Fast Configuration of Energy Storage Capacity in Stand-Alone and Grid-Connected Wind Energy Systems

Directory of Open Access Journals (Sweden)

Haixiang Zang

2016-12-01

Full Text Available In this paper, a novel method is proposed and applied to quickly calculate the capacity of energy storage for stand-alone and grid-connected wind energy systems, according to the discrete Fourier transform theory. Based on practical wind resource data and power data, which are derived from the American Wind Energy Technology Center and HOMER software separately, the energy storage capacity of a stand-alone wind energy system is investigated and calculated. Moreover, by applying the practical wind power data from a wind farm in Fujian Province, the energy storage capacity for a grid-connected wind system is discussed in this paper. This method can also be applied to determine the storage capacity of a stand-alone solar energy system with practical photovoltaic power data.

BER performance comparison of optical CDMA systems with/without turbo codes

Science.gov (United States)

Kulkarni, Muralidhar; Chauhan, Vijender S.; Dutta, Yashpal; Sinha, Ravindra K.

2002-08-01

In this paper, we have analyzed and simulated the BER performance of a turbo coded optical code-division multiple-access (TC-OCDMA) system. A performance comparison has been made between uncoded OCDMA and TC-OCDMA systems employing various OCDMA address codes (optical orthogonal codes (OOCs), Generalized Multiwavelength Prime codes (GMWPC's), and Generalized Multiwavelength Reed Solomon code (GMWRSC's)). The BER performance of TC-OCDMA systems has been analyzed and simulated by varying the code weight of address code employed by the system. From the simulation results, it is observed that lower weight address codes can be employed for TC-OCDMA systems that can have the equivalent BER performance of uncoded systems employing higher weight address codes for a fixed number of active users.

Capacity of spectrum sharing Cognitive Radio systems over Nakagami fading channels at low SNR

KAUST Repository

Sboui, Lokman

2013-06-01

In this paper, we study the ergodic capacity of Cognitive Radio (CR) spectrum sharing systems at low power regime. We focus on Nakagami fading channels. We formally define the low power regime and present closed form expressions of the capacity in the low power regime under various types of interference and/or power constraints, depending on the available channel state information (CSI) of the cross link (CL) between the secondary user transmitter and the primary user receiver. We explicitly characterize two regimes where either the interference constraint or the power constraint dictates the optimal power profile. Our framework also highlights the effects of different fading parameters on the secondary link ergodic capacity. Interestingly, we show that the low power regime analysis provides a specific insight on the capacity behavior of CR that has not been reported by previous studies. © 2013 IEEE.

Strict optical orthogonal codes for purely asynchronous code-division multiple-access applications

Science.gov (United States)

Zhang, Jian-Guo

1996-12-01

Strict optical orthogonal codes are presented for purely asynchronous optical code-division multiple-access (CDMA) applications. The proposed code can strictly guarantee the peaks of its cross-correlation functions and the sidelobes of any of its autocorrelation functions to have a value of 1 in purely asynchronous data communications. The basic theory of the proposed codes is given. An experiment on optical CDMA systems is also demonstrated to verify the characteristics of the proposed code.

The hydraulic capacity of deteriorating sewer systems.

Science.gov (United States)

Pollert, J; Ugarelli, R; Saegrov, S; Schilling, W; Di Federico, V

2005-01-01

Sewer and wastewater systems suffer from insufficient capacity, construction flaws and pipe deterioration. Consequences are structural failures, local floods, surface erosion and pollution of receiving waters bodies. European cities spend in the order of five billion Euro per year for wastewater network rehabilitation. This amount is estimated to increase due to network ageing. The project CARE-S (Computer Aided RE-habilitation of Sewer Networks) deals with sewer and storm water networks. The final project goal is to develop integrated software, which provides the most cost-efficient system of maintenance, repair and rehabilitation of sewer networks. Decisions on investments in rehabilitation often have to be made with uncertain information about the structural condition and the hydraulic performance of a sewer system. Because of this, decision-making involves considerable risks. This paper presents the results of research focused on the study of hydraulic effects caused by failures due to temporal decline of sewer systems. Hydraulic simulations are usually carried out by running commercial models that apply, as input, default values of parameters that strongly influence results. Using CCTV inspections information as dataset to catalogue principal types of failures affecting pipes, a 3D model was used to evaluate their hydraulic consequences. The translation of failures effects in parameters values producing the same hydraulic conditions caused by failures was carried out through the comparison of laboratory experiences and 3D simulations results. Those parameters could be the input of 1D commercial models instead of the default values commonly inserted.

On the average capacity and bit error probability of wireless communication systems

KAUST Repository

Yilmaz, Ferkan

2011-12-01

Analysis of the average binary error probabilities and average capacity of wireless communications systems over generalized fading channels have been considered separately in the past. This paper introduces a novel moment generating function-based unified expression for both average binary error probabilities and average capacity of single and multiple link communication with maximal ratio combining. It is a matter to note that the generic unified expression offered in this paper can be easily calculated and that is applicable to a wide variety of fading scenarios, and the mathematical formalism is illustrated with the generalized Gamma fading distribution in order to validate the correctness of our newly derived results. © 2011 IEEE.

The effects of changes to estuarine hydrology on system phosphorous retention capacity: The Mondego estuary, Portugal

DEFF Research Database (Denmark)

Lillebo, A. I.; Otero, M.; Coelho, J. P.

2012-01-01

with the highest PO4-P adsorption capacity (Q* = 657 mu g P g(-1) wwt), thus the PO4-P availability in the water column was mostly dependent on the mineralization processes, which is in agreement with previous findings; ii) After 1998, the water residence time diminished from moderate (weeks) to short (days......). This change coincided with a diversion of the water to an area with a much lower PO4-P adsorption capacity (Q* = 410 mu g P g(-1) wwt), which represented a decrease in 7.3% of the system adsorption capacity. This means that sediments were not able to adsorb much of the PO4-P and a higher equilibrium...... in the estuary, we framed the hypothesis that the significant increase of DIP could be related to different sorption capacities of the sediments. The results highlighted two scenarios: i) Before 1998 the nutrient-rich freshwater input from the upstream cultivated lands entered the system through the area...

Measurement-Based Spatial Correlation and Capacity of Indoor Distributed MIMO System

Directory of Open Access Journals (Sweden)

Yan Zhang

2013-01-01

Full Text Available Distributed MIMO (D-MIMO system is one of the candidates for future wireless access networks. In this study, the spatial correlation and capacity in indoor D-MIMO system are presented. All results are from the actual channel measurements in typical indoor scenarios, including office and corridor. Based on measured data, spatial correlation coefficients between distributed transmitting antennas are analyzed. Although the literature about D-MIMO system assumes the small scale fading between distributed antennas is independent, we find that spatial correlation may still exist in specific propagation scenario. This correlation can also degrade the performance of D-MIMO system. To mitigate the impact of spatial correlation, one efficient method is to use transmitting antenna selection technique.

Higher order capacity statistics of multi-hop transmission systems over Rayleigh fading channels

KAUST Repository

Yilmaz, Ferkan; Tabassum, Hina; Alouini, Mohamed-Slim

2012-01-01

In this paper, we present an exact analytical expression to evaluate the higher order statistics of the channel capacity for amplify and forward (AF) multihop transmission systems operating over Rayleigh fading channels. Furthermore, we present

A stochastic dynamic model for optimal timing of investments in new generation capacity in restructured power systems

International Nuclear Information System (INIS)

Botterud, Audun; Korpaas, Magnus

2007-01-01

In this paper we formulate the power generation investment problem for a decentralised and profit-maximising investor operating in a restructured and competitive power system. In particular, we look at how uncertainty influences the optimal timing of investments in new power generation capacity. A real options approach is used to take long-term uncertainty in load growth, and its influence on future electricity prices, into account in the investment optimisation. In order to value the operational flexibility of a new power plant we use an electricity price model, where the spot price is a function of load level and installed generation capacity, in addition to short-term uncertainties and temporal fluctuations in the market. The investor's income from a capacity payment, which also can depend on the system's total capacity balance, can also be represented. Hence, with the optimisation model we can analyse power plant profitability and optimal timing of new investments under different market designs. In a case study from the Nordic electricity market we analyse the effect of uncertainty on optimal investment timing. We also examine how a fixed or variable capacity payment would influence the investment decision, and discuss the system consequences of the resulting investment strategies. (author)

Energy system, electricity market and economic studies on increasing nuclear power capacity

International Nuclear Information System (INIS)

Forsstrom, J.; Pursiheimo, E.; Kekkonen, V.; Honkatukia, J.

2010-04-01

Objective of this research project is to examine effects of addition of nuclear capacity from three different angles by using energy system, electricity market and economic analysis. In each area the analysis is based on computational methods. Finland is a member of Nordic electricity market which is further connected to networks of Continental Europe and Russia. Due to the foreign connections Finland has been able to import inexpensive electricity from its neighboring countries and this state is expected to continue. Addition of nuclear capacity lowers electricity import demand, affects level of electricity price decreasingly and decreases shortfall of installed production capacity. Substantial additions of nuclear power capacity and generous import supply have disadvantageous effect on profitability of combined heat and power production. The development of import possibilities depends on progression of difficult-to-estimate balance between electricity consumption and production in the neighboring countries. Investments on nuclear power increase national product during the construction phase. Growth of employment is also rather significant, especially during the construction phase. In the long term permanent jobs will be created too. Increase of employment is held back by increasing real wages, but it is though evident that consumer purchasing power is improved due to these nuclear power developments. (orig.)

Influence of capacity- and time-constrained intermediate storage in two-stage food production systems

DEFF Research Database (Denmark)

Akkerman, Renzo; van Donk, Dirk Pieter; Gaalman, Gerard

2007-01-01

In food processing, two-stage production systems with a batch processor in the first stage and packaging lines in the second stage are common and mostly separated by capacity- and time-constrained intermediate storage. This combination of constraints is common in practice, but the literature hardly...... of systems like this. Contrary to the common sense in operations management, the LPT rule is able to maximize the total production volume per day. Furthermore, we show that adding one tank has considerable effects. Finally, we conclude that the optimal setup frequency for batches in the first stage...... pays any attention to this. In this paper, we show how various capacity and time constraints influence the performance of a specific two-stage system. We study the effects of several basic scheduling and sequencing rules in the presence of these constraints in order to learn the characteristics...

Conceptual design of hydrogen isotopes chromatographic separation system with super large capacity

International Nuclear Information System (INIS)

Xie Bo; Weng Kuiping; Liu Yunnu; Hou Jianping

2012-01-01

A super large capacity hydrogen isotopes separation system, including total plan, unit (including making and purification of gas, three-grade chromatographic columns, gas loop and auto-control, and carrier recovery) and experimental scheme, had been designed on the basis of a series of hydrogen-deuterium experiments by temperature programmed de- sorption. The characteristic of the system was that desorption kinetic parameters could be directly calculated from the hydrogen isotope separation desorption spectra information. In other words, the complicated dynamic process of separation could be described by the desorption rate equation, shape parameter and desorption activation energy calculation on the condition of the experimental data and appropriate assumptions (equilibrium and adsorption, uniform surface). In previous work, an experimental series of operation to verify the successive enrichment of D 2 from a H 2 -D 2 mixture, the production of the deuterium from natural hydrogen and the recovery of tritium such as from the nuclear heavy-water were carried out using MS5A at 77 K. This work was only conceptual design, so it was necessary to identify the availability of super large capacity system by experiment. (authors)

Outage capacity of multicarrier systems

KAUST Repository

Yilmaz, Ferkan; Alouini, Mohamed-Slim

2010-01-01

The probability density function and the cumulative distribution function of the product of shifted Gamma variates are obtained in terms of the generalized Fox's H function. Using these new results, the exact outage capacity of multi carrier transmission through a slow Nakagami-m fading channel is presented. Moreover, it is shown that analytical and simulation results are in perfect agreement. © 2009 IEEE.

Models for estimating runway landing capacity with Microwave Landing System (MLS)

Science.gov (United States)

Tosic, V.; Horonjeff, R.

1975-01-01

A model is developed which is capable of computing the ultimate landing runway capacity, under ILS and MLS conditions, when aircraft population characteristics and air traffic control separation rules are given. This model can be applied in situations when only a horizontal separation between aircraft approaching a runway is allowed, as well as when both vertical and horizontal separations are possible. It is assumed that the system is free of errors, that is that aircraft arrive at specified points along the prescribed flight path precisely when the controllers intend for them to arrive at these points. Although in the real world there is no such thing as an error-free system, the assumption is adequate for a qualitative comparison of MLS with ILS. Results suggest that an increase in runway landing capacity, caused by introducing the MLS multiple approach paths, is to be expected only when an aircraft population consists of aircraft with significantly differing approach speeds and particularly in situations when vertical separation can be applied. Vertical separation can only be applied if one of the types of aircraft in the mix has a very steep descent angle.

Outage capacity of multicarrier systems

KAUST Repository

Yilmaz, Ferkan

2010-01-01

The probability density function and the cumulative distribution function of the product of shifted Gamma variates are obtained in terms of the generalized Fox\\'s H function. Using these new results, the exact outage capacity of multi carrier transmission through a slow Nakagami-m fading channel is presented. Moreover, it is shown that analytical and simulation results are in perfect agreement. © 2009 IEEE.

Radiologic total lung capacity measurement. Development and evaluation of a computer-based system

Energy Technology Data Exchange (ETDEWEB)

Seeley, G.W.; Mazzeo, J.; Borgstrom, M.; Hunter, T.B.; Newell, J.D.; Bjelland, J.C.

1986-11-01

The development of a computer-based radiologic total lung capacity (TLC) measurement system designed to be used by non-physician personnel is detailed. Four operators tested the reliability and validity of the system by measuring inspiratory PA and lateral pediatric chest radiographs with a Graf spark pen interfaced to a DEC VAX 11/780 computer. First results suggest that the ultimate goal of developing an accurate and easy to use TLC measurement system for non-physician personnel is attainable.

Disease burden and mental health system capacity: WHO Atlas study of 117 low- and middle-income countries.

Science.gov (United States)

McBain, Ryan; Salhi, Carmel; Morris, Jodi E; Salomon, Joshua A; Betancourt, Theresa S

2012-12-01

Treatment coverage for mental disorders ranges from less than 10% to more than 90% across low- and middle-income (LAMI) countries. Studies have yet to examine whether the capacity of mental health systems might be adversely affected by the burdens of unrelated conditions such as HIV/AIDS. To examine whether the magnitude of disease burden from communicable, perinatal, maternal and nutritional conditions - commonly referred to as Group 1 diseases - is inversely associated with mental health system capacity in LAMI countries. Multiple regression analyses were undertaken using data from 117 LAMI countries included in the 2011 World Health Organization (WHO) Mental Health Atlas. Capacity was defined in terms of human resources and infrastructure. Regressions controlled for effects of political stability, government health expenditures, income inequality and neuropsychiatric disease burden. Higher Group 1 disease burden was associated with fewer psychiatrists, psychologists and nurses in the mental health sector, as well as reduced numbers of out-patient facilities and psychiatric beds in mental hospitals and general hospitals (t = -2.06 to -7.68, Pmental health system capacity in LAMI countries may be adversely affected by the magnitude of their Group 1 disease burden.

Femtosecond Laser System for Research on High-Speed Optical Transmultiplexing and Coding

National Research Council Canada - National Science Library

Weiner, Andrew

1997-01-01

.... This would fill an important need in both TDM packet networks and bit-parallel WDM linds. The research also aims at experimental tests of an ultrashort pulse code-division, multiple-access (CDMA...

Installed capacity in New York

International Nuclear Information System (INIS)

Charlton, J.

2006-01-01

This presentation discussed capacity issues related to the New York Independent System Operator (NYISO). The NYISO's market volume was approximately $11 billion in 2005, and it was responsible for providing 32,075 MW of electricity at peak load to its users. Regulatory uncertainty is currently discouraging investment in new generating resources. All load serving entities are required to contract for sufficient capacity in order to meet their capacity obligations. Market participants currently determine capacity and energy revenues. The NYISO market allows suppliers to recover variable costs for providing ancillary services, and the economic value of the revenue source governs decisions made in the wholesale electricity market. The installed capacity market was designed as a spot auction deficiency auction. Phased-in demand curves are used to modify the installed capacity market's design. A sloped demand curve mechanism is used to value capacity above the minimum requirement for both reliability and competition. Participation in the day-ahead market enhances competition and exerts downward pressure on energy and ancillary service market prices. It was concluded that the market structures and design features of the installed capacity markets recognize the need for system reliability in addition to encouraging robust competition and recognizing energy price caps and regulatory oversights. tabs., figs

System capacity and economic modeling computer tool for satellite mobile communications systems

Science.gov (United States)

Wiedeman, Robert A.; Wen, Doong; Mccracken, Albert G.

1988-01-01

A unique computer modeling tool that combines an engineering tool with a financial analysis program is described. The resulting combination yields a flexible economic model that can predict the cost effectiveness of various mobile systems. Cost modeling is necessary in order to ascertain if a given system with a finite satellite resource is capable of supporting itself financially and to determine what services can be supported. Personal computer techniques using Lotus 123 are used for the model in order to provide as universal an application as possible such that the model can be used and modified to fit many situations and conditions. The output of the engineering portion of the model consists of a channel capacity analysis and link calculations for several qualities of service using up to 16 types of earth terminal configurations. The outputs of the financial model are a revenue analysis, an income statement, and a cost model validation section.

Investigating the sealing capacity of a seal system in rock salt (DOPAS project)

Energy Technology Data Exchange (ETDEWEB)

Jantschik, Kyra; Moog, Helge C.; Czaikowski, Oliver; Wieczorek, Klaus [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Braunschweig (Germany)

2016-11-15

This paper describes research and development work on plugging and sealing repositories, an issue of fundamental importance for the rock salt option which represents one of the three European repository options, besides the clay rock and the crystalline rock options. The programme aims at providing experimental data needed for the theoretical analysis of the long-term sealing capacity of concrete- based sealing materials. In order to demonstrate hydro-mechanical material stability under representative load scenarios, a comprehensive laboratory testing programme is carried out. This comprises investigation of the sealing capacity of the combined seal system and impact of the so-called excavation-damaged zones (EDZ) as well as investigation of the hydro-chemical long-term stability of the seal in contact with different brines under diffusive and advective conditions. This paper presents experimental approaches and preliminary results from laboratory investigations on salt concrete and combined systems as obtained to date.

Simulation of PV/FC power hybrid system. Change of system capacity with load form factor; Taiyoko hatsuden nenryo denchi hybrid system no simulation. Fuka keijoritsu ni yoru system yoryo no henka

Energy Technology Data Exchange (ETDEWEB)

Sekiguchi, N.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

1997-11-25

Study is conducted of a photovoltaic/fuel-cell hybrid system whose power storage is a hydrogen storage that uses a hydrogen absorbing alloy. In a simulation in this research, the solar cell conversion efficiency is changed from 15.0% to 21.0% and the fuel cell power conversion efficiency from 40.0% to 50.0%, and the resultant changes in the capacity and operation rate are investigated for each of the devices in the system. The findings follow. A 1.0% change in the solar cell conversion efficiency results in a 4.8kW change in the solar cell capacity and a 1.6-ton change in the hydrogen storage capacity. With a 1.0% change in the fuel cell power conversion efficiency, there is a 14.7kW change in the solar cell capacity and a 5.3-ton change in the hydrogen storage capacity. The fuel cell capacity is not dependent on the solar cell conversion efficiency or fuel cell power conversion efficiency but on the maximum load in each of the load form factors. The rate of occurrence of an operation rate of less than 30% is 54.7% both in DC/DC converter and hydrogen generator, 24.6% in fuel cells, and 16.7% in the DC/DC inverter. 7 refs., 7 figs., 1 tab.