WorldWideScience

Sample records for cavity ring-down spectroscopy

  1. Sensitivity limits of continuous wave cavity ring-down spectroscopy.

    Science.gov (United States)

    Huang, Haifeng; Lehmann, Kevin K

    2013-12-19

    An optimized nonlinear least-squares fit algorithm for data processing in cavity ring-down spectroscopy (CRDS) is discussed, which improves the calculation efficiency substantially over using a general purpose fitting package. Theoretical absorption sensitivity limits for both the detector noise and the shot noise limited situations are derived and compared with experimental results. The effect of limiting the bandwidth of detection system on ring-down signal is discussed and compared with real ring-down data. The optimal trigger level and fitting interval are obtained for continuous wave cavity ring-down spectroscopy (cw-CRDS) in both the detector noise and shot noise limits, with the resulting sensitivity in units of cm(-1) per (Hz(1/2)) derived. Interestingly, it is found that the optimized shot noise limited sensitivity in cw-CRDS method is, in principle, comparable with the ultimate sensitivity of noise-immune cavity-enhanced optical heterodyne molecular spectroscopy (NICE-OHMS). PMID:23978273

  2. Chemical Sensing Using Fiber Cavity Ring-Down Spectroscopy

    Directory of Open Access Journals (Sweden)

    Hans-Peter Loock

    2010-03-01

    Full Text Available Waveguide-based cavity ring-down spectroscopy (CRD can be used for quantitative measurements of chemical concentrations in small amounts of liquid, in gases or in films. The change in ring-down time can be correlated to analyte concentration when using fiber optic sensing elements that change their attenuation in dependence of either sample absorption or refractive index. Two types of fiber cavities, i.e., fiber loops and fiber strands containing reflective elements, are distinguished. Both types of cavities were coupled to a variety of chemical sensor elements, which are discussed and compared.

  3. Pulsed cavity ring-down spectroscopy in combustion environments

    OpenAIRE

    Evertsen, Rogier

    2002-01-01

    This thesis gives an introduction to pulsed cavity ring-down absorption spectroscopy (CRDS) and its application in combustion research. Experimental results have been compared to numerical simulations, providing a means to validate reaction mechanisms and numerical approaches. Up to now, the application of CRDS in the field of combustion research has mainly been focused on sub-atmospheric flames and quantitative investigations of atmospheric flames have been very limited. Here, it has been ap...

  4. Frequency-Agile Differential Cavity Ring-Down Spectroscopy

    Science.gov (United States)

    Reed, Zachary; Hodges, Joseph

    2015-06-01

    The ultimate precision of highly sensitive cavity-enhanced spectroscopic measurements is often limited by interferences (etalons) caused by weak coupled-cavity effects. Differential measurements of ring-down decay constants have previously been demonstrated to largely cancel these effects, but the measurement acquisition rates were relatively low [1,2]. We have previously demonstrated the use of frequency agile rapid scanning cavity ring-down spectroscopy (FARS-CRDS) for acquisition of absorption spectra [3]. Here, the method of rapidly scanned, frequency-agile differential cavity ring-down spectroscopy (FADS-CRDS) is presented for reducing the effect of these interferences and other shot-to-shot statistical variations in measured decay times. To this end, an electro-optic phase modulator (EOM) with a bandwidth of 20 GHz is driven by a microwave source, generating pairs of sidebands on the probe laser. The optical resonator acts as a highly selective optical filter to all laser frequencies except for one tunable sideband. This sideband may be stepped arbitrarily from mode-to-mode of the ring-down cavity, at a rate limited only by the cavity buildup/decay time. The ability to probe any cavity mode across the EOM bandwidth enables a variety of methods for generating differential spectra. The differential mode spacing may be changed, and the effect of this method on suppressing the various coupled-cavity interactions present in the system is discussed. Alternatively, each mode may also be differentially referenced to a single point, providing immunity to temporal variations in the base losses of the cavity while allowing for conventional spectral fitting approaches. Differential measurements of absorption are acquired at 3.3 kHz and a minimum detectable absorption coefficient of 5 x10-12 cm-1 in 1 s averaging time is achieved. 1. J. Courtois, K. Bielska, and J.T Hodges J. Opt. Soc. Am. B, 30, 1486-1495, 2013 2. H.F. Huang and K.K. Lehmann App. Optics 49, 1378

  5. Measurement of atmospheric ozone by cavity ring-down spectroscopy.

    Science.gov (United States)

    Washenfelder, R A; Wagner, N L; Dube, W P; Brown, S S

    2011-04-01

    Ozone plays a key role in both the Earth's radiative budget and photochemistry. Accurate, robust analytical techniques for measuring its atmospheric abundance are of critical importance. Cavity ring-down spectroscopy has been successfully used for sensitive and accurate measurements of many atmospheric species. However, this technique has not been used for atmospheric measurements of ozone, because the strongest ozone absorption bands occur in the ultraviolet spectral region, where Rayleigh and Mie scattering cause significant cavity losses and dielectric mirror reflectivities are limited. Here, we describe a compact instrument that measures O3 by chemical conversion to NO2 in excess NO, with subsequent detection by cavity ring-down spectroscopy. This method provides a simple, accurate, and high-precision measurement of atmospheric ozone. The instrument consists of two channels. The sum of NO2 and converted O3 (defined as Ox) is measured in the first channel, while NO2 alone is measured in the second channel. NO2 is directly detected in each channel by cavity ring-down spectroscopy with a laser diode light source at 404 nm. The limit of detection for O3 is 26 pptv (2 sigma precision) at 1 s time resolution. The accuracy of the measurement is ±2.2%, with the largest uncertainty being the effective NO2 absorption cross-section. The linear dynamic range of the instrument has been verified from the detection limit to above 200 ppbv (r2>99.99%). The observed precision on signal (2 sigma) with 41 ppbv O3 is 130 pptv in 1 s. Comparison of this instrument to UV absorbance instruments for ambient O3 concentrations shows linear agreement (r2=99.1%) with slope of 1.012±0.002. PMID:21366216

  6. Cavity Ring-Down Spectroscopy for Trace Gas Analysis

    International Nuclear Information System (INIS)

    Cavity Ring-Down Spectroscopy (CRDS) is a novel technique of measurement of the absorption coefficient based on determination of the Q-factor of an optical resonator which contains the investigated absorber. We present a modified CRDS method (so called CRD-Spectrography) in which the signal is simultaneously analysed within a broad spectral range. This technique was used for monitoring of trace gases (nitrogen oxides) in the atmosphere. Another modification of CRDS technique allows to determine the transient absorption coefficient. This method was applied for studies of kinetics of CH radical produced by pulsed electric discharge in methane. (author)

  7. Use of laser diodes in cavity ring-down spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Zare, R.N.; Paldus, B.A.; Ma, Y.; Xie, J. [Stanford Univ., CA (United States)

    1997-12-31

    We have demonstrated that cavity ring-down spectroscopy (CRDS), a highly sensitive absorption technique, is versatile enough to serve as a complete diagnostic for materials process control. In particular, we have used CRDS in the ultraviolet to determine the concentration profile of methyl radicals in a hot-filament diamond reactor; we have applied CRDS in the mid-infrared to detect 50 ppb of methane in a N{sub 2} environment; and, we have extended CRDS so that we can use continuous-wave diode laser sources. Using a laser diode at 810 nm, we were able to achieve a sensitivity of 2 x 10{sup -8} cm{sup -1}. Thus, CRDS can be used not only as an in situ diagnostic for investigating the chemistry of diamond film deposition, but it can also be used as a gas purity diagnostic for any chemical vapor deposition system.

  8. Measurements of carbon-14 with cavity ring-down spectroscopy

    Science.gov (United States)

    McCartt, A. D.; Ognibene, T.; Bench, G.; Turteltaub, K.

    2015-10-01

    Accelerator Mass Spectrometry (AMS) is the most sensitive method for quantitation of 14C in biological samples. This technology has been used in a variety of low dose, human health related studies over the last 20 years when very high sensitivity was needed. AMS helped pioneer these scientific methods, but its expensive facilities and requirements for highly trained technical staff have limited their proliferation. Quantification of 14C by cavity ring-down spectroscopy (CRDS) offers an approach that eliminates many of the shortcomings of an accelerator-based system and would supplement the use of AMS in biomedical research. Our initial prototype, using a non-ideal wavelength laser and under suboptimal experimental conditions, has a 3.5-modern, 1- σ precision for detection of milligram-sized, carbon-14-elevated samples. These results demonstrate proof of principle and provided a starting point for the development of a spectrometer capable of biologically relevant sensitivities.

  9. A Cavity Ring-Down Spectroscopy Mercury Continuous Emission Monitor

    Energy Technology Data Exchange (ETDEWEB)

    Christopher C. Carter

    2004-12-15

    The Sensor Research & Development Corporation (SRD) has undertaken the development of a Continuous Emissions Monitor (CEM) for mercury based on the technique of Cavity Ring-Down Spectroscopy (CRD). The project involved building an instrument for the detection of trace levels of mercury in the flue gas emissions from coal-fired power plants. The project has occurred over two phases. The first phase concentrated on the development of the ringdown cavity and the actual detection of mercury. The second phase dealt with the construction and integration of the sampling system, used to carry the sample from the flue stack to the CRD cavity, into the overall CRD instrument. The project incorporated a Pulsed Alexandrite Laser (PAL) system from Light Age Incorporated as the source to produce the desired narrow band 254 nm ultra-violet (UV) radiation. This laser system was seeded with a diode laser to bring the linewidth of the output beam from about 150 GHz to less than 60 MHz for the fundamental beam. Through a variety of non-linear optics the 761 nm fundamental beam is converted into the 254 nm beam needed for mercury detection. Detection of the mercury transition was verified by the identification of the characteristic natural isotopic structure observed at lower cavity pressures. The five characteristic peaks, due to both natural isotopic abundance and hyperfine splitting, provided a unique identifier for mercury. SRD scientists were able to detect mercury in air down below 10 parts-per-trillion by volume (pptr). This value is dependent on the pressure and temperature within the CRD cavity at the time of detection. Sulfur dioxide (SO{sub 2}) absorbs UV radiation in the same spectral region as mercury, which is a significant problem for most mercury detection equipment. However, SRD has not only been able to determine accurate mercury concentrations in the presence of SO{sub 2}, but the CRD instrument can in fact determine the SO{sub 2} concentration as well. Detection of

  10. A CAVITY RING-DOWN SPECTROSCOPY MERCURY CONTINUOUS EMISSION MONITOR

    Energy Technology Data Exchange (ETDEWEB)

    Christopher C. Carter, Ph.D.

    2003-06-30

    Previous work on the detection of mercury using the cavity ring-down (CRD) technique has concentrated on the detection and characterization of the desired mercury transition. Interferent species present in flue gas emissions have been tested as well as a simulated flue gas stream. Additionally, work has been done on different mercury species such as the elemental and oxidized forms. The next phase of the effort deals with the actual sampling system. This sampling system will be responsible for acquiring a sample stream from the flue gas stack, taking it to the CRD cavity where it will be analyzed and returning the gas stream to the stack. In the process of transporting the sample gas stream every effort must be taken to minimize any losses of mercury to the walls of the sampling system as well as maintaining the mercury in its specific state (i.e. elemental, oxidized, or other mercury compounds). SRD first evaluated a number of commercially available sampling systems. These systems ranged from a complete sampling system to a number of individual components for specific tasks. SRD engineers used some commercially available components and designed a sampling system suited to the needs of the CRD instrument. This included components such as a pyrolysis oven to convert all forms of mercury to elemental mercury, a calibration air source to ensure mirror alignment and quality of the mirror surfaces, and a pumping system to maintain the CRD cavity pressure from atmospheric pressure (760 torr) down to about 50 torr. SRD also began evaluating methods for the CRD instrument to automatically find the center of a mercury transition. This procedure is necessary as the instrument must periodically measure the baseline losses of the cavity off of the mercury resonance and then return to the center of the transition to accurately measure the mercury concentration. This procedure is somewhat complicated due to the isotopic structure of the 254 nm mercury transition. As a result of

  11. Dual-etalon, cavity-ring-down, frequency comb spectroscopy.

    Energy Technology Data Exchange (ETDEWEB)

    Strecker, Kevin E.; Chandler, David W.

    2010-10-01

    The 'dual etalon frequency comb spectrometer' is a novel low cost spectometer with limited moving parts. A broad band light source (pulsed laser, LED, lamp ...) is split into two beam paths. One travels through an etalon and a sample gas, while the second arm is just an etalon cavity, and the two beams are recombined onto a single detector. If the free spectral ranges (FSR) of the two cavities are not identical, the intensity pattern at the detector with consist of a series of heterodyne frequencies. Each mode out of the sample arm etalon with have a unique frequency in RF (radio-frequency) range, where modern electronics can easily record the signals. By monitoring these RF beat frequencies we can then determine when an optical frequencies is absorbed. The resolution is set by the FSR of the cavity, typically 10 MHz, with a bandwidth up to 100s of cm{sup -1}. In this report, the new spectrometer is described in detail and demonstration experiments on Iodine absorption are carried out. Further we discuss powerful potential next generation steps to developing this into a point sensor for monitoring combustion by-products, environmental pollutants, and warfare agents.

  12. Radiocarbon Dioxide detection based on Cavity Ring-Down Spectroscopy and a Quantum Cascade Laser

    OpenAIRE

    Genoud, Guillaume; Vainio, Markku; Phillips, Hilary; Dean, Julian; Merimaa, Mikko

    2015-01-01

    Monitoring of radiocarbon ($^{14}$C) in carbon dioxide is demonstrated using mid-infrared spectroscopy and a quantum cascade laser. The measurement is based on cavity ring-down spectroscopy, and a high sensitivity is achieved with a simple setup. The instrument was tested using a standardised sample containing elevated levels of radiocarbon. Radiocarbon dioxide could be detected from samples with an isotopic ratio $^{14}$C/C as low as 50 parts-per-trillion, corresponding to an activity of 5 k...

  13. Integrating cavity ring-down spectroscopy (ICRDS) and the direct measurement of absorption coefficients

    Science.gov (United States)

    Fry, Edward S.; Mason, John D.

    2016-04-01

    Absorption of light at various wavelengths (i.e. absorption spectroscopy) is a powerful tool for identifying the presence of chemical compounds or specific substances in a sample. Cavity ring down spectroscopy (CRDS) is a well-known technique for very high sensitivity absorption spectroscopy. Another technique, integrating cavity spectroscopy has the additional unique feature of providing accurate absorption data even in the presence of severe scattering. This paper describes a combination of these two techniques that has led to an extremely powerful and useful new technology—integrating CRDS.

  14. Rapid-swept CW cavity ring-down laser spectroscopy for carbon isotope analysis

    International Nuclear Information System (INIS)

    With the aim of developing a portable system for an in field isotope analysis, we investigate an isotope analysis based on rapid-swept CW cavity ring-down laser spectroscopy, in which the concentration of a chemical species is derived from its photo absorbance. Such a system can identify the isotopomer and still be constructed as a quite compact system. We have made some basic experimental measurements of the overtone absorption lines of carbon dioxide (12C16O2, 13C16O2) by rapid-swept cavity ring-down spectroscopy with a CW infrared diode laser at 6,200 cm-1 (1.6 μm). The isotopic ratio has been obtained as (1.07±0.13)x10-2, in good agreement with the natural abundance within experimental uncertainty. The detection sensitivity in absorbance has been estimated to be 3x10-8 cm-1. (author)

  15. Measurement of OH Radicals in Dielectric Barrier Discharge Plasmas by Cavity Ring-Down Spectroscopy

    International Nuclear Information System (INIS)

    Near-infrared continuous wave cavity ring-down spectroscopy was applied to measure the OH radicals in dielectric barrier discharge plasmas, which play an important role in combustion systems, atmospheric chemistry and the removal of air pollutants by non-thermal plasmas. The P-branches of OH X2Πi ν = 2 <- ν = 0) bands were used for number density measurements. The OH number density and plasma temperature were determined for different applied voltages, gas pressures and concentrations of both oxygen and water. The temporal evolution of the OH number density was obtained by using the 'time window' method, which was used to extract individual ring-down times at different times in a half period of the sine wave applied voltage in dielectric barrier discharge plasmas.

  16. Time resolved super continuum Cavity Ring-Down Spectroscopy for multicomponent gas detection

    International Nuclear Information System (INIS)

    In this work, we present a variation of the technique CRDS (Cavity Ring-Down Spectroscopy) to obtain simultaneously a multicomponent absorption spectrum in a broad visible range. This new approach uses the Supercontinuum (SC) spectrum (resulting from irradiation of nonlinear media by femtosecond lasers, or simply generated by compact sources) as a light source to illuminate the cavity. In this context it is described the features of the modules assembling a MC-SC-CRDS (Multicomponent Supercontinuum Cavity Ring-Down Spectroscopy): a set of high reflectivity mirrors, the resonant cavity and the detection system. Some problems related to the multimode excitation, stray light, effective use of the dynamic range of the detector, the poor resolution of the instrument to resolve narrow absorption lines are issued. We present the absorption spectra of H2O (polyads 4υ, 4υ + δ) and O2 (spin-forbidden b-X branch) measured simultaneously by this technique in the visible range and a comparison with the absorption lines based on HITRAN database is made to demonstrate the functionality of this method. (author)

  17. Comparison of water isotope analysis between cavity ring-down spectroscopy and isotope ratio mass spectrometry

    International Nuclear Information System (INIS)

    δD and δ18O of natural waters with δ18O ranging from -24 to -6‰ were measured using a cavity ring-down spectroscopy (CRDS) in order to confirm that the CRDS method can be an alternative to conventional isotope ratio mass spectrometry (IRMS). The deviations of δD and δ18O values obtained using the CRDS and IRMS methods are less than 0.8‰ and 0.3‰, respectively, which are practically sufficient for geochemical/environmental researches of natural waters, indicating that the CRDS method can be an alternative to the IRMS methods for environmental liquid water samples. (author)

  18. Hollow-core fiber based linear cavity ring-down spectroscopy for gaseous oxygen detection

    Science.gov (United States)

    Munzke, Dorit; Böhm, Michael; Reich, Oliver

    2014-05-01

    We present a spectroscopic technique that combines the benefits of cavity ring-down spectroscopy and a hollowcore photonic crystal fiber. The 10m fiber is placed inside an optical cavity and acts both as the sample cell (volume = 442 nL) and as a waveguide. Due to the high reflectivity of the cavity mirrors and rather small coupling losses, the effective optical path length can be increased up to 70m. Therefore, as a figure of merit the volume per optical interaction path length is calculated to 6.3 nL m-1. Oxygen detection is performed at 760 nm while scanning across an absorption line. The optical loss due to sample absorption is determined by measuring the ring-down time of light traveling inside the cavity. Results are compared to HITRAN database showing a discrepancy of only 2.5% of the absorption coefficient. This method is of interest for applications that require sensitive measurements on sample volumes of few nanoliters to microliters without the need of calibration.

  19. Miniature chemical sensor combining molecular recognition with evanescent wave cavity ring-down spectroscopy

    International Nuclear Information System (INIS)

    A new chemical detection technology has been realized that addresses DOE environmental management needs. The new technology is based on a variant of the sensitive optical absorption technique, cavity ring-down spectroscopy (CRDS). Termed evanescent-wave cavity ring-down spectroscopy (EW-CRDS), the technology employs a miniature solid-state optical resonator having an extremely high Q-factor as the sensing element, where the high-Q is achieved by using ultra-low-attenuation optical materials, ultra-smooth surfaces, and ultra-high reflectivity coatings, as well as low-diffraction-loss designs. At least one total-internal reflection (TIR) mirror is integral to the resonator permitting the concomitant evanescent wave to probe the ambient environment. Several prototypes have been designed, fabricated, characterized, and applied to chemical detection. Moreover, extensions of the sensing concept have been explored to enhance selectivity, sensitivity, and range of application. Operating primarily in the visible and near IR regions, the technology inherently enables remote detection by optical fiber. Producing 11 archival publications, 5 patents, 19 invited talks, 4 conference proceedings, a CRADA, and a patent-license agreement, the project has realized a new chemical detection technology providing >100 times more sensitivity than comparable technologies, while also providing practical advantages

  20. Design of fiber magnetic field sensor based on fiber Bragg grating Fabry-Perot cavity ring-down spectroscopy

    Science.gov (United States)

    Li, Qi; Chen, Haiyan

    2015-06-01

    A novel fiber magnetic sensor based on the fiber Bragg grating Fabry-Perot (FBG-FP) cavity ring-down technique with pulse laser injection is proposed and demonstrated theoretically. A general expression of the intensity of the output electric field is derived, and the effect of the external magnetic field on the ring-down time is discussed. The results show that the output light intensity and the ring-down time of the FBG-FP cavity are in the inverse proportion to the magnitude of the external magnetic field. Our results demonstrate the new concept of the fiber magnetic sensor with the FBG-FP cavity ring-down spectroscopy and the technical feasibility.

  1. Miniature Chemical Sensor combining Molecular Recognition with Evanescent Wave Cavity Ring-Down Spectroscopy

    International Nuclear Information System (INIS)

    To address the chemical sensing needs of DOE, a new class of chemical sensors is being developed that enables qualitative and quantitative, remote, real-time, optical diagnostics of chemical species in hazardous gas, liquid, and semi-solid phases by employing evanescent wave cavity ring-down spectroscopy (EW-CRDS). The feasibility and sensitivity of EW-CRDS was demonstrated previously under Project No.60231. The objective of this project is to enhance the selectivity and domain of application of EW-CRDS. Selectivity is enhanced by using molecular recognition (MR) chemistry and polarized ''fingerprint'' near-IR spectroscopy, while the domain of application is expanded by combining EW-CRDS with the unique optical properties of nanoparticles and by extending the technique to liquids

  2. Toward a real-time measurement of atmospheric mercury concentrations using cavity ring-down spectroscopy

    Directory of Open Access Journals (Sweden)

    X. Faïn

    2009-10-01

    Full Text Available A new sensor based on cavity ring-down spectroscopy (CRDS has been developed for the measurement of gaseous elemental mercury (Hg0 mass concentration with sub-ng m−3 detection limit and high temporal resolution. Cavity ring-down spectroscopy is a direct absorption technique that utilizes path lengths of up to multiple kilometers in a compact absorption cell and has a significantly higher sensitivity than conventional absorption spectroscopy. Our prototype uses a frequency-doubled, tuneable dye laser emitting pulses at ~253.65 nm with a pulse repetition frequency of 50 Hz. The dye laser incorporates a unique piezo element attached to its tuning grating allowing it to tune the laser on and off the Hg0 absorption line on a pulse to pulse basis to facilitate differential absorption measurements. Hg0 absorption measurements with this CRDS laboratory prototype are highly linearly related to Hg0 concentrations determined by a Tekran 2537B analyzer over a Hg0 concentration range of four orders of magnitude, from 0.2 ng m−3 to 573 ng m−3 implying excellent linearity of both instruments. The current CRDS instrument has a~sensitivity of 0.10 ng m−3 at 10 s time resolution. This tool opens new prospects for the study of Hg0 because of its high temporal resolution and reduced limited sample volume requirements (<0.5 l of sample air. Future applications may include ambient Hg0 flux measurements with eddy covariance techniques, which require measurements of Hg0 concentrations with sub-ng m−3 sensitivity and sub-second time resolution.

  3. Double resonant absorption measurement of acetylene symmetric vibrational states probed with cavity ring down spectroscopy

    CERN Document Server

    Karhu, J; Vainio, M; Metsälä, M; Hoekstra, S; Halonen, L

    2016-01-01

    A novel mid-infrared/near-infrared double resonant absorption setup for studying infrared-inactive vibrational states is presented. A strong vibrational transition in the mid-infrared region is excited using an idler beam from a singly resonant continuous-wave optical parametric oscillator, to populate an intermediate vibrational state. High output power of the optical parametric oscillator and the strength of the mid-infrared transition result in efficient population transfer to the intermediate state, which allows measuring secondary transitions from this state with a high signal-to-noise ratio. A secondary, near-infrared transition from the intermediate state is probed using cavity ring down spectroscopy, which provides high sensitivity in this wavelength region. Due to the narrow linewidths of the excitation sources, the rovibrational lines of the secondary transition are measured with sub-Doppler resolution. The setup is used to access a previously unreported symmetric vibrational state of acetylene, $\

  4. Metrological problems of gas analyzers based on wavelength-scanned cavity ring-down spectroscopy

    Science.gov (United States)

    Konopel'ko, L. A.; Beloborodov, V. V.; Rumyantsev, D. V.; Chubchenko, Ya. K.; Elizarov, V. V.

    2015-06-01

    Wavelength-scanned cavity ring-down spectroscopy (WS CRDS) is used in gas analysis. Calibration gas mixtures containing carbon monoxide, carbon-12 dioxide, carbon-13 dioxide, methane, and formaldehyde are used to determine the metrological characteristics of WS CRDS gas analyzers. Most experimental results are in agreement with the declared data. For gas mixtures in which the gas matrix differs from air, the broadening of spectral lines related to the interaction of particles causes significant errors in the concentration measurements. Such effects that neutralize the advantages of the WS CRDS method are studied in this work. The coefficients that can be used to correct the results of the WS CRDS gas analyzers and compensate for errors related to different gas matrices are presented.

  5. Design of a cavity ring-down spectroscopy diagnostic for negative ion rf source SPIDER

    Energy Technology Data Exchange (ETDEWEB)

    Pasqualotto, R.; Alfier, A.; Lotto, L. [Consorzio RFX-Associazione Euratom-Enea sulla Fusione, corso Stati Uniti 4, I-35127 Padova (Italy)

    2010-10-15

    The rf source test facility SPIDER will test and optimize the source of the 1 MV neutral beam injection systems for ITER. Cavity ring-down spectroscopy (CRDS) will measure the absolute line-of-sight integrated density of negative (H{sup -} and D{sup -}) ions, produced in the extraction region of the source. CRDS takes advantage of the photodetachment process: negative ions are converted to neutral hydrogen atoms by electron stripping through absorption of a photon from a laser. The design of this diagnostic is presented with the corresponding simulation of the expected performance. A prototype operated without plasma has provided CRDS reference signals, design validation, and results concerning the signal-to-noise ratio.

  6. Birefringence-induced frequency beating in high-finesse cavities by continuous-wave cavity ring-down spectroscopy

    Science.gov (United States)

    Dupré, Patrick

    2015-11-01

    By analyzing the decaying intensity, leaking out a high-finesse cavity previously "filled" by a cw laser source (using the cavity ring-down spectroscopy technique), we observed frequency beating between what we think are two orthogonal eigenpolarization states of the intracavity electromagnetic field. The time decay (ring down) is analyzed by varying the angle of the polarization analyzer located in front of the detector. A full modeling of the observed signal is proposed. It is based on the Jones matrix formalism required for modeling the cavity behavior following a rotated phase shifter. The full transfer function is first established in the frequency domain, and then Fourier transformed to recover the temporal response. The same optical cavity, i.e., constituted of the same set of mirrors, is used at two different wavelengths (˜800 and ˜880 nm). It demonstrates the differences in behavior between a high-finesse cavity (˜400 000 ) and a lower finesse cavity (˜50 000 ). Beating frequency, characteristics time, and beat amplitude are mainly discussed versus the analyzer angle. A cavity birefringence of ˜1.6 ×10-5 rad, resulting from the mirror birefringence is suggested. If the current analysis is in agreement with pulsed CRDS experiments (polarimetry) obtained in an isotropic moderate-finesse cavity, it differs from a recent work report on a high-finesse cavity associated with a source mode locking [Phys. Rev. A 85, 013837 (2012), 10.1103/PhysRevA.85.013837].

  7. Determination of dissolved methane in natural waters using headspace analysis with cavity ring-down spectroscopy

    International Nuclear Information System (INIS)

    Highlights: • A method for determining low nanomolar dissolved CH4 was developed. • The methane detection utilizes cavity ring-down spectroscopy (CRDS). • Use of CRDS requires less time, materials and labor than typical of GC analysis. • Relative standard deviations of ∼4% were achieved at low nM CH4. • Applications to seawater and river water are presented. - Abstract: Methane (CH4) is the third most abundant greenhouse gas (GHG) but is vastly understudied in comparison to carbon dioxide. Sources and sinks to the atmosphere vary considerably in estimation, including sources such as fresh and marine water systems. A new method to determine dissolved methane concentrations in discrete water samples has been evaluated. By analyzing an equilibrated headspace using laser cavity ring-down spectroscopy (CRDS), low nanomolar dissolved methane concentrations can be determined with high reproducibility (i.e., 0.13 nM detection limit and typical 4% RSD). While CRDS instruments cost roughly twice that of gas chromatographs (GC) usually used for methane determination, the process presented herein is substantially simpler, faster, and requires fewer materials than GC methods. Typically, 70-mL water samples are equilibrated with an equivalent amount of zero air in plastic syringes. The equilibrated headspace is transferred to a clean, dry syringe and then drawn into a Picarro G2301 CRDS analyzer via the instrument’s pump. We demonstrate that this instrument holds a linear calibration into the sub-ppmv methane concentration range and holds a stable calibration for at least two years. Application of the method to shipboard dissolved methane determination in the northern Gulf of Mexico as well as river water is shown. Concentrations spanning nearly six orders of magnitude have been determined with this method

  8. Development of a pulsed laser with emission at 1053 nm for Cavity Ring-Down Spectroscopy

    International Nuclear Information System (INIS)

    In this work, a pulsed and Q-switched laser resonator was developed using the double-beam mode-controlling technique. A Nd:LiYF4 crystal with 0,8mol% of doping concentration was used to generate a giant pulse with duration of 5,5 ns (FWHM), 1,2 mJ of energy and 220 kW peak power for the Cavity Ring-Down Spectroscopy (CRDS) technique. The CRDS technique is used to measure absorption spectra for gases, liquids and solids. With the CRDS technique it is possible to measure losses with high degree of accuracy, underscoring the sensitivity that is confirmed by the use of mirrors with high reflectivity. With this technique, the losses by reflection and scattering of transparent materials were evaluated. By calibrating the resonant cavity, it was possible to measure the losses in the samples with resolution of 0,045%, the maximum being reached by 0,18%. The calibration was possible because there was obtained to measure a decay time of approximately 20 μs with the empty cavity. Besides was obtained a method for determining the refractive index of transparent materials with accuracy of five decimals. (author)

  9. Precise and accurate d13C analysis of rock samples using Flash Combustion–Cavity Ring Down Laser Spectroscopy

    DEFF Research Database (Denmark)

    Balslev-Clausen, David Morten; Dahl, Tais Wittchen; Saad, Nabil; Rosing, Minik Thorleif

    2013-01-01

    expert know-how. Here, we measure 13C/12C in natural sedimentary samples using Combustion Module - Cavity Ring Down Spectroscopy (CM-CRDS) with average precision and standard reproducibility of 0.05‰ and 0.2‰ (1 s.d., n = 17), respectively. The accuracy of the technique was determined from certified...

  10. Novel use of cavity ring-down spectroscopy to investigate aquatic carbon cycling from microbial to ecosystem scales

    NARCIS (Netherlands)

    Maher, D.T.; Santos, I.S.; Leuven, J.R.F.W.; Oakes, J.M.; Erler, D.V.; Carvalho, M.C.; Eyre, B.D.

    2013-01-01

    Development of cavity ring-down spectroscopy (CRDS) has enabled real-time monitoring of carbon stable isotope ratios of carbon dioxide and methane in air. Here we demonstrate that CRDS can be adapted to assess aquatic carbon cycling processes from microbial to ecosystem scales. We first measured in

  11. Cavity ring-down spectroscopy sensor for detection of hydrogen chloride

    Directory of Open Access Journals (Sweden)

    C. L. Hagen

    2013-08-01

    Full Text Available A laser-based cavity ring-down spectroscopy (CRDS sensor for measurement of hydrogen chloride (HCl has been developed and characterized. The instrument uses light from a distributed-feedback diode laser at 1742 nm coupled to a high finesse optical cavity to make sensitive and quantifiable concentration measurements of HCl based on optical absorption. The instrument has a (1σ limit of detection of < 20 pptv in 1 min and has high specificity to HCl. The measurement response time to changes in input HCl concentration is < 15 s. Validation studies with a previously calibrated permeation tube setup show an accuracy of better than 10%. The CRDS sensor was preliminarily tested in the field with two other HCl instruments (mist chamber and chemical ionization mass spectrometry, all of which were in broad agreement. The mist chamber and CRDS sensors both showed a 400 pptv plume within 50 pptv agreement. The sensor also allows simultaneous sensitive measurements of water and methane, and minimal hardware modification would allow detection of other near-infrared absorbers.

  12. Open-path cavity ring-down spectroscopy sensor for atmospheric ammonia

    Science.gov (United States)

    Shadman, Soran; Rose, Charles; Yalin, Azer P.

    2016-07-01

    An open-path cavity ring-down spectroscopy (CRDS) sensor has been developed for measurement of atmospheric ammonia (NH3) and represents the first use of open-path CRDS in the mid-infrared region. The sensor uses a continuous-wave distributed feedback quantum cascade laser at 10.33 μm to target strong absorption features. The optical cavity is constructed with two high-reflectivity mirrors ( R = 0.9995). The open-path configuration removes inlet effects, which are very challenging for closed-path instruments, and can be enabling for compact, low-power designs. Sensor performance was validated in the laboratory by measuring known concentrations in a closed-path configuration. The open-path configuration was validated by comparison against a commercial closed-path CRDS instrument for outdoor measurements at a small feed lot. Ammonia concentrations from the two instruments showed good agreement with slope of 0.990 ( R 2 = 0.92), for 5-min averages. The precision of the open-path instrument was found from Allan variance studies as 1.2 ppb (2-σ) for 3-s measurement durations.

  13. Radiocarbon dioxide detection based on cavity ring-down spectroscopy and a quantum cascade laser.

    Science.gov (United States)

    Genoud, G; Vainio, M; Phillips, H; Dean, J; Merimaa, M

    2015-04-01

    Monitoring of radiocarbon (C14) in carbon dioxide is demonstrated using mid-infrared spectroscopy and a quantum cascade laser. The measurement is based on cavity ring-down spectroscopy, and a high sensitivity is achieved with a simple setup. The instrument was tested using a standardized sample containing elevated levels of radiocarbon. Radiocarbon dioxide could be detected from samples with an isotopic ratio C14/C as low as 50 parts-per-trillion, corresponding to an activity of 5  kBq/m(3) in pure CO(2), or 2  Bq/m(3) in air after extraction of the CO(2) from an air sample. The instrument is simple, compact, and robust, making it the ideal tool for on-site measurements. It is aimed for monitoring radioactive gaseous emissions in a nuclear power environment, during the operation and decommissioning of nuclear power plants. Its high sensitivity also makes it the ideal tool for the detection of leaks in radioactive waste repositories. PMID:25831328

  14. Radiocarbon Dioxide detection based on Cavity Ring-Down Spectroscopy and a Quantum Cascade Laser

    CERN Document Server

    Genoud, Guillaume; Phillips, Hilary; Dean, Julian; Merimaa, Mikko

    2015-01-01

    Monitoring of radiocarbon ($^{14}$C) in carbon dioxide is demonstrated using mid-infrared spectroscopy and a quantum cascade laser. The measurement is based on cavity ring-down spectroscopy, and a high sensitivity is achieved with a simple setup. The instrument was tested using a standardised sample containing elevated levels of radiocarbon. Radiocarbon dioxide could be detected from samples with an isotopic ratio $^{14}$C/C as low as 50 parts-per-trillion, corresponding to an activity of 5 kBq/m$^3$ in pure CO$_2$, or 2 Bq/m$^3$ in air after extraction of the CO$_2$ from an air sample. The instrument is simple, compact and robust, making it the ideal tool for on-site measurements. It is aimed for monitoring of radioactive gaseous emissions in nuclear power environment, during the operation and decommissioning of nuclear power plants. Its high sensitivity also makes it the ideal tool for the detection of leaks in radioactive waste repositories.

  15. Compact near-IR and mid-IR cavity ring down spectroscopy device

    Science.gov (United States)

    Miller, J. Houston (Inventor)

    2011-01-01

    This invention relates to a compact cavity ring down spectrometer for detection and measurement of trace species in a sample gas using a tunable solid-state continuous-wave mid-infrared PPLN OPO laser or a tunable low-power solid-state continuous wave near-infrared diode laser with an algorithm for reducing the periodic noise in the voltage decay signal which subjects the data to cluster analysis or by averaging of the interquartile range of the data.

  16. Modification of a commercial cavity ring-down spectroscopy NO2 detector for enhanced sensitivity

    International Nuclear Information System (INIS)

    Nitrogen dioxide (NO2) plays a central role in atmospheric chemistry, air pollution, and biogeochemical cycles. Many analytical techniques have been developed to detect NO2, but only chemiluminescence-based instruments are commonly, commercially available. There remains a need for a fast, light, and simple method to directly measure NO2. In this work we describe the modification and characterization of a small, commercially available cavity ring-down spectroscopy (CRDS) NO2 detector suitable for surface and aircraft monitoring. A metal oxide scrubber was added to remove NO2, and provide a chemical zero, improving the detection limit (3σ of the background noise) from several parts per billion by volume (ppbv) to 0.06 ppbv, integrated over 60 s. Known interferences by water and particles were removed using Nafion tubing and a 1 μm Teflon filter, respectively. A 95% response time of 18±1 s was observed for a step change in concentration. The CRDS detector was run in parallel to an ozone chemiluminescence device with photolytic conversion of NO2 to NO. The two instruments measured ambient air in suburban Maryland. A least-squares fit to the comparison data resulted a slope of 0.960±0.002 and R of 0.995, showing agreement within experimental uncertainty.

  17. Determination of dissolved methane in natural waters using headspace analysis with cavity ring-down spectroscopy.

    Science.gov (United States)

    Roberts, Hannah M; Shiller, Alan M

    2015-01-26

    Methane (CH4) is the third most abundant greenhouse gas (GHG) but is vastly understudied in comparison to carbon dioxide. Sources and sinks to the atmosphere vary considerably in estimation, including sources such as fresh and marine water systems. A new method to determine dissolved methane concentrations in discrete water samples has been evaluated. By analyzing an equilibrated headspace using laser cavity ring-down spectroscopy (CRDS), low nanomolar dissolved methane concentrations can be determined with high reproducibility (i.e., 0.13 nM detection limit and typical 4% RSD). While CRDS instruments cost roughly twice that of gas chromatographs (GC) usually used for methane determination, the process presented herein is substantially simpler, faster, and requires fewer materials than GC methods. Typically, 70-mL water samples are equilibrated with an equivalent amount of zero air in plastic syringes. The equilibrated headspace is transferred to a clean, dry syringe and then drawn into a Picarro G2301 CRDS analyzer via the instrument's pump. We demonstrate that this instrument holds a linear calibration into the sub-ppmv methane concentration range and holds a stable calibration for at least two years. Application of the method to shipboard dissolved methane determination in the northern Gulf of Mexico as well as river water is shown. Concentrations spanning nearly six orders of magnitude have been determined with this method. PMID:25542359

  18. Liquid-phase and evanescent-wave cavity ring-down spectroscopy in analytical chemistry.

    Science.gov (United States)

    van der Sneppen, L; Ariese, F; Gooijer, C; Ubachs, W

    2009-01-01

    Due to its simplicity, versatility, and straightforward interpretation into absolute concentrations, molecular absorbance detection is widely used in liquid-phase analytical chemistry. Because this method is inherently less sensitive than zero-background techniques such as fluorescence detection, alternative, more sensitive measurement principles are being explored. This review discusses one of these: cavity ring-down spectroscopy (CRDS). Advantages of this technique include its long measurement pathlength and its insensitivity to light-source-intensity fluctuations. CRDS is already a well-established technique in the gas phase, so we focus on two new modes: liquid-phase CRDS and evanescent-wave (EW)-CRDS. Applications of liquid-phase CRDS in analytical chemistry focus on improving the sensitivity of absorbance detection in liquid chromatography. Currently, EW-CRDS is still in early stages: It is used to study basic interactions between molecules and silica surfaces. However, in the future this method may be used to develop, for instance, biosensors with high specificity. PMID:20636052

  19. Characterisation and cleaning of oxide support materials for cavity ring-down spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Kartouzian, Aras; Thaemer, Martin; Heiz, Ulrich [Lehrstuhl fuer Physikalische Chemie, Technische Universitaet Muenchen, Garching (Germany)

    2010-05-15

    Cavity ring-down spectroscopy (CRDS) has been applied to characterise different oxide materials (amorphous silica, borosilicate and yttria stabilised zirconia YSZ) which are suitable to be used as support material for size-selected metal clusters. The sensitivity of the spectroscopic method was improved by means of transversal mode matching and spatial filtering of the laser beam profile, reducing the relative error by 50%. The high sensitivity of CRDS allows the detection of trace amounts of impurities and defect sites in the samples, based on their absorption properties. In YSZ, traces of Nd have been detected. The optical quality of the substrates was determined qualitatively according to the measured optical losses. CRDS surface maps have been used to monitor the homogeneity of the support materials, and the influence of ion bombardment on the surface has been studied. It is shown that in the case of BK7 {sup registered} substrates, sputtering with low energy Ar{sup +} ions could remove deposited gold clusters almost completely causing very low damage to the surface. These results were confirmed analytically. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  20. Cavity Ring-Down Spectroscopy for Gaseous Fission Products Trace Measurements in Sodium Fast Reactors

    International Nuclear Information System (INIS)

    Safety and availability are key issues of the generation IV reactors. Hence, the three radionuclide confinement barriers, including fuel cladding, must stay tight during the reactor operation. During the primary gaseous failure, fission products xenon and krypton are released. Their fast and sensitive detection guarantees the first confinement barrier tightness. In the frame of the French ASTRID project, an optical spectroscopy technique - Cavity Ring Down Spectroscopy (CRDS) - is investigated for the gaseous fission products measurement. A dedicated CRDS set-up is needed to detect the rare gases with a commercial laser. Indeed, the CRDS is coupled to a glow discharge plasma, which generates a population of metastable atoms. The xenon plasma conditions are optimized to 110 Pa and 1.3 W (3 mA). The production efficiency of metastable Xe is then 0.8 %, stable within 0.5% during hours. The metastable number density is proportional to the xenon over argon molar fraction. The spectroscopic parameters of the strong 823.16 nm xenon transition are calculated and/or measured in order to optimize the fit of the experimental spectra and make a quantitative measurement of the metastable xenon. The CRDS is coupled to the discharge cell. The laser intensity inside the cavity is limited by the optical saturation process, resulting from the strong optical pumping of the metastable state. The resulting weak CRDS signal requires a fast and very sensitive photodetector. A 600 ppt xenon molar fraction was measured by CRDS. With the present set-up, the detection limits are estimated from the baseline noise to approximately 20 ppt for each even isotope, 60 ppt for the 131Xe and 55 ppt for the 129Xe. This sensitivity matches the specifications required for gaseous leak measurement; approximately 100 ppt for 133Xe (4 GBq/m3) and 10 ppb for stable isotopes. The odd isotopes are selectively measured, whereas the even isotopes overlap, a spectroscopic feature that applies for stable or

  1. Absolute measurements of total peroxy nitrate mixing ratios by thermal dissociation blue diode laser cavity ring-down spectroscopy.

    Science.gov (United States)

    Paul, Dipayan; Osthoff, Hans D

    2010-08-01

    Peroxycarboxylic nitric anhydrides (PANs) have long been recognized as important trace gas constituents of the troposphere. Here, we describe a blue diode laser thermal dissociation cavity ring-down spectrometer for rapid and absolute measurements of total peroxyacyl nitrate (SigmaPAN) abundances at ambient concentration levels. The PANs are thermally dissociated and detected as NO2, whose mixing ratios are quantified by optical absorption at 405 nm relative to a reference channel kept at ambient temperature. The effective NO2 absorption cross-section at the diode laser emission wavelength was measured to be 6.1 x 10(-19) cm2 molecule(-1), in excellent agreement with a prediction based on a projection of a high-resolution literature absorption spectrum onto the laser line width. The performance, i.e., accuracy and precision of measurement and matrix effects, of the new 405 nm thermal dissociation cavity ring-down spectrometer was evaluated and compared to that of a 532 nm thermal dissociation cavity ring-down spectrometer using laboratory-generated air samples. The new 405 nm spectrometer was considerably more sensitive and compact than the previously constructed version. The key advantage of laser thermal dissociation cavity ring-down spectroscopy is that the measurement can be considered absolute and does not need to rely on external calibration. PMID:20698583

  2. Chemical Sensing Using Infrared Cavity Enhanced Spectroscopy: Short Wave Infrared Cavity Ring Down Spectroscopy (SWIR CRDS) Sensor

    Energy Technology Data Exchange (ETDEWEB)

    Williams, Richard M.; Harper, Warren W.; Aker, Pam M.; Thompson, Jason S.; Stewart, Timothy L.

    2003-10-01

    The principal goal of Pacific Northwest National Laboratory's (PNNL's) Remote Spectroscopy Project is to explore and develop the science and technology behind point and stand off infrared (IR) spectroscopic chemical sensors that are needed for detecting weapons proliferation activity and countering terrorism. Missions addressed include detecting chemical, biological, and nuclear weapons and their production; counter terrorism measures that involve screening luggage, personnel, and shipping containers for explosives, firearms, narcotics, chemical weapons and/or their residues; and mapping of contaminated areas. The science and technology developed in this program is dual use in that it additionally supports progress in a diverse set of agendas that include chemical weapons defense programs, air operations activities, emissions monitoring, law enforcement, and medical diagnostics. Sensors for these missions require extremely low limits of detection because many of the targeted signature species are either present in low concentrations or have extremely low vapor pressures. The sensors also need to be highly selective as the environments that they will be operated in will contain a variety of interferent species and false positive detection is not an option. PNNL has been working on developing a class of sensors that draw vapor into optical cavities and use laser-based spectroscopy to identify and quantify the vapor chemical content. The cavity enhanced spectroscopies (CES) afford extreme sensitivity, excellent selectivity, noise immunity, and rapid, real-time, in-situ chemical characterization. PNNL's CES program is currently focused on developing two types of sensors. The first one, which is based on cavity ring down spectroscopy (CRDS), uses short wave infrared (SWIR) lasers to interrogate species. The second sensor, which is based on noise immune cavity-enhanced optical heterodyne molecular spectroscopy (NICE OHMS), uses long wave infrared (LWIR

  3. Dual-etalon cavity ring-down frequency-comb spectroscopy with broad band light source

    Energy Technology Data Exchange (ETDEWEB)

    Chandler, David W; Strecker, Kevin E

    2014-04-01

    In an embodiment, a dual-etalon cavity-ring-down frequency-comb spectrometer system is described. A broad band light source is split into two beams. One beam travels through a first etalon and a sample under test, while the other beam travels through a second etalon, and the two beams are recombined onto a single detector. If the free spectral ranges ("FSR") of the two etalons are not identical, the interference pattern at the detector will consist of a series of beat frequencies. By monitoring these beat frequencies, optical frequencies where light is absorbed may be determined.

  4. Cavity ring-down spectroscopy of CO2 overtone bands near 830 nm

    International Nuclear Information System (INIS)

    Three bands 4003i–00001 (i=2, 3, 4) of the Fermi pentad of 12C16O2 near 830 nm have been recorded with a continuous-wave cavity ring down spectrometer. A sensitivity at the 5×10–11 cm−1 level allowed us to obtain line positions and intensities of these very weak bands. The measured line intensities of these three bands together with those published for the 10051–00001 and 10052–00001 bands were used to obtain the effective dipole moment parameters of 12C16O2 for the ΔP=17 series of transitions, where P=2V1+V2+3V3 is a polyad number (Vi (i=1, 2, 3) are vibrational quantum numbers). Comparisons of the measured line positions and intensities of the 4003i–00001 (i=2, 3, 4) bands to those from the AMES and GEISA line lists are given. - Highlights: • Cavity ring-down spectra of 12C16O2 around 830 nm were measured. • Line positions and intensities of transitions were obtained for three bands. • The line positions predicted by the effective Hamiltonian model agree well with the measured values

  5. Toward real-time measurement of atmospheric mercury concentrations using cavity ring-down spectroscopy

    Directory of Open Access Journals (Sweden)

    X. Faïn

    2010-03-01

    Full Text Available Cavity ring-down spectroscopy (CRDS is a direct absorption technique that utilizes path lengths up to multiple kilometers in a compact absorption cell and has a significantly higher sensitivity than conventional absorption spectroscopy. This tool opens new prospects for study of gaseous elemental mercury (Hg0 because of its high temporal resolution and reduced sample volume requirements (<0.5 l of sample air. We developed a new sensor based on CRDS for measurement of (Hg0 mass concentration. Sensor characteristics include sub-ng m−3 detection limit and high temporal resolution using a frequency-doubled, tuneable dye laser emitting pulses at ~253.65 nm with a pulse repetition frequency of 50 Hz. The dye laser incorporates a unique piezo element attached to its tuning grating allowing it to tune the laser on and off the Hg0 absorption line on a pulse-to-pulse basis to facilitate differential absorption measurements. Hg0 absorption measurements with this CRDS laboratory prototype are highly linearly related to Hg0 concentrations determined by a Tekran 2537B analyzer over an Hg0 concentration range from 0.2 ng m−3 to 573 ng m−3, implying excellent linearity of both instruments. The current CRDS instrument has a sensitivity of 0.10 ng Hg0 m−3 at 10-s time resolution. Ambient-air tests showed that background Hg0 levels can be detected at low temporal resolution (i.e., 1 s, but also highlight a need for high-frequency (i.e., pulse-to-pulse differential on/off-line tuning of the laser wavelength to account for instabilities of the CRDS system and variable background absorption interferences. Future applications may include ambient Hg0 flux measurements with eddy covariance techniques, which require measurements of Hg0 concentrations with sub-ng m−3 sensitivity and sub-second time

  6. Eddy covariance flux measurements of gaseous elemental mercury using cavity ring-down spectroscopy.

    Science.gov (United States)

    Pierce, Ashley M; Moore, Christopher W; Wohlfahrt, Georg; Hörtnagl, Lukas; Kljun, Natascha; Obrist, Daniel

    2015-02-01

    A newly developed pulsed cavity ring-down spectroscopy (CRDS) system for measuring atmospheric gaseous elemental mercury (GEM) concentrations at high temporal resolution (25 Hz) was used to successfully conduct the first eddy covariance (EC) flux measurements of GEM. GEM is the main gaseous atmospheric form, and quantification of bidirectional exchange between the Earth's surface and the atmosphere is important because gas exchange is important on a global scale. For example, surface GEM emissions from natural sources, legacy emissions, and re-emission of previously deposited anthropogenic pollution may exceed direct primary anthropogenic emissions. Using the EC technique for flux measurements requires subsecond measurements, which so far has not been feasible because of the slow time response of available instrumentation. The CRDS system measured GEM fluxes, which were compared to fluxes measured with the modified Bowen ratio (MBR) and a dynamic flux chamber (DFC). Measurements took place near Reno, NV, in September and October 2012 encompassing natural, low-mercury (Hg) background soils and Hg-enriched soils. During nine days of measurements with deployment of Hg-enriched soil in boxes within 60 m upwind of the EC tower, the covariance of GEM concentration and vertical wind speed was measured, showing that EC fluxes over an Hg-enriched area were detectable. During three separate days of flux measurements over background soils (without Hg-enriched soils), no covariance was detected, indicating fluxes below the detection limit. When fluxes were measurable, they strongly correlated with wind direction; the highest fluxes occurred when winds originated from the Hg-enriched area. Comparisons among the three methods showed good agreement in direction (e.g., emission or deposition) and magnitude, especially when measured fluxes originated within the Hg-enriched soil area. EC fluxes averaged 849 ng m(-2) h(-1), compared to DFC fluxes of 1105 ng m(-2) h(-1) and MBR fluxes

  7. Cavity Ring-down Spectroscopic System And Method

    KAUST Repository

    Alquaity, Awad Bin Saud

    2015-05-14

    A system and method for cavity ring-down spectroscopy can include a pulsed quantum cascade laser, an optical ring-down cavity, a photodetector, and an oscilloscope. The system and method can produce pulse widths of less than 200 ns with bandwidths greater than 300 pm, as well as provide temporal resolution of greater than 10 .mu.s.

  8. Spectral line-shapes investigation with Pound-Drever-Hall-locked frequency-stabilized cavity ring-down spectroscopy

    Science.gov (United States)

    Cygan, A.; Wójtewicz, S.; Domysławska, J.; Masłowski, P.; Bielska, K.; Piwiński, M.; Stec, K.; Trawiński, R. S.; Ozimek, F.; Radzewicz, C.; Abe, H.; Ido, T.; Hodges, J. T.; Lisak, D.; Ciuryło, R.

    2013-10-01

    A review of recent experiments involving a newly developed Pound-Drever-Hall-locked frequency-stabilized cavity ring-down spectroscopy (PDH-locked FS-CRDS) system is presented. By comparison to standard FS-CRDS, the PDH lock of the probe laser to the ring-down cavity optimized coupling into the cavity, thus increasing the ring-down signal acquisition rate nearly 300-fold to 14 kHz and reducing the noise-equivalent absorption coefficient by more than an order of magnitude to 7 × 10-11 cm-1. We discuss how averaging approximately 1000 spectra yielded a signal-to-noise ratio of 220000. We also discuss how the spectrum frequency axis was linked to an optical frequency comb, thus enabling absolute frequency measurements of molecular optical transitions at sub-MHz levels. Applications of the spectrometer to molecular line-shape studies are also presented. For these investigations, we use semi-classical line-shape models that consider the influence of Dicke narrowing as well as the speed dependence of the pressure broadening and shifting to fit spectra. We show that the improved precision and spectrum fidelity of the spectrometer enable precise determinations of line-shape parameters. We also discuss the importance of line-shape analysis with regard to the development of new spectroscopic databases as well as in the optical determination of the Boltzmann constant.

  9. Noise caused by a finite extinction ratio of the light modulator in CW cavity ring-down spectroscopy

    Science.gov (United States)

    Huang, H.; Lehmann, K. K.

    2009-02-01

    A model is presented for the effect of a finite extinction ratio of the light modulator used in continuous wave cavity ring-down spectroscopy (CW-CRDS) experiments. We present a simple analytical expression for the minimum isolation required to prevent a significant increase in the fluctuations of the cavity decay rate, which determine the sensitivity of the method. We also present systematic measurements of the signal to noise in CW-CRDS as a function of the effective isolation of the light modulator, and excellent agreement with the model is found.

  10. In situ measurements of OH radicals in dielectric barrier discharge plasmas with cw-cavity ring-down spectroscopy

    International Nuclear Information System (INIS)

    An apparatus of continuous wave cavity ring-down spectroscopy (cw-CRDS) has been constructed with the noise (RMS) equivalent absorption 3 x 10-9 cm-1. In situ quantitative measurements of OH radicals in dielectric barrier discharge (DBD) plasmas at low pressure using cw-CRDS are described. The influence of discharge voltage and pressure on number density of OH has been investigated. Results show that the OH production increases at low pressure with increasing discharge pressure; however, the number density of OH decreases due to electron attachment of H2O at higher pressure. The number density of OH radical increases with increasing discharge voltage and discharge frequency because of the increase of electron density and electron energy. (authors)

  11. Real-Tme Boron Nitride Erosion Measurements of the HiVHAc Thruster via Cavity Ring-Down Spectroscopy

    Science.gov (United States)

    Lee, Brian C.; Yalin, Azer P.; Gallimore, Alec; Huang, Wensheng; Kamhawi, Hani

    2013-01-01

    Cavity ring-down spectroscopy was used to make real-time erosion measurements from the NASA High Voltage Hall Accelerator thruster. The optical sensor uses 250 nm light to measure absorption of atomic boron in the plume of an operating Hall thruster. Theerosion rate of the High Voltage Hall Accelerator thruster was measured for discharge voltages ranging from 330 to 600 V and discharge powers ranging from 1 to 3 kW. Boron densities as high as 6.5 x 10(exp 15) per cubic meter were found within the channel. Using a very simple boronvelocity model, approximate volumetric erosion rates between 5.0 x 10(exp -12) and 8.2 x 10(exp -12) cubic meter per second were found.

  12. Nuclear spin state-resolved cavity ring-down spectroscopy diagnostics of a low-temperature H3+ -dominated plasma

    International Nuclear Information System (INIS)

    We have applied a continuous-wave near-infrared cavity ring-down spectroscopy method to study the parameters of a H3+ -dominated plasma at temperatures in the range 77–200 K. We monitor populations of three rotational states of the ground vibrational state corresponding to para and ortho nuclear spin states in the discharge and the afterglow plasma in time and conclude that abundances of para and ortho states and rotational temperatures are well defined and stable. The non-trivial dependence of a relative population of para- H3+ on a relative population of para-H2 in a source H2 gas is described. The results described in this paper are valuable for studies of state-selective dissociative recombination of H3+ ions with electrons in the afterglow plasma and for the design of sources of H3+ ions in a specific nuclear spin state. (paper)

  13. Evanescent-wave cavity ring-down spectroscopy for enhanced detection of surface binding under flow injection analysis conditions.

    Science.gov (United States)

    van der Sneppen, L; Buijs, J B; Gooijer, C; Ubachs, W; Ariese, F

    2008-06-01

    The feasibility of liquid-phase evanescent-wave cavity ring-down spectroscopy (EW-CRDS) for surface-binding studies under flow-injection analysis (FIA) conditions is demonstrated. The EW-CRDS setup consists of an anti-reflection coated Dove prism inside a linear cavity (with standard or super-polishing of the total internal reflective (TIR) surface). A teflon spacer with an elliptical hole clamped on this surface acts as a 20 muL sized flow cell. The baseline noise of this system is of the order of 10(-4) absorbance units; the baseline remains stable over a prolonged time and the prism surface does not become contaminated during repeated injections of the reversibly adsorbing test dyes Crystal Violet (CV) and Direct Red 10 (DR10). At typical FIA or liquid chromatography (LC) flow rates, the system has sufficient specificity to discriminate between species with different surface affinities. For CV a much stronger decrease in ring-down time is observed than calculated based on its bulk concentration and the effective depth probed by the evanescent wave, indicating binding of this positively charged dye to the negatively charged prism surface. The amount of adsorption can be influenced by adjusting the flow rate or the eluent composition. At a flow rate of 0.5 mL/min, an enrichment factor of 60 was calculated for CV; for the poorly adsorbing dye DR10 it is 5. Super-polishing of the already polished TIR surface works counter-productively. The adsorbing dye Crystal Violet has a detection limit of 3 muM for the standard polished surface; less binding occurs on the super-polished surface and the detection limit is 5 muM. Possible applications of EW-CRDS for studying surface binding or the development of bio-assays are discussed. PMID:18559152

  14. High-accuracy continuous airborne measurements of greenhouse gases (CO2 and CH4) using the cavity ring-down spectroscopy (CRDS) technique

    NARCIS (Netherlands)

    Chen, H.; Winderlich, J.; Gerbig, C.; Hoefer, A.; Rella, C. W.; Crosson, E. R.; Van Pelt, A. D.; Steinbach, J.; Kolle, O.; Beck, V.; Daube, B. C.; Gottlieb, E. W.; Chow, V. Y.; Santoni, G. W.; Wofsy, S. C.

    2010-01-01

    High-accuracy continuous measurements of greenhouse gases (CO2 and CH4) during the BARCA (Balancao Atmosferico Regional de Carbono na Amazonia) phase B campaign in Brazil in May 2009 were accomplished using a newly available analyzer based on the cavity ring-down spectroscopy (CRDS) technique. This

  15. Novel use of cavity ring-down spectroscopy to investigate aquatic carbon cycling from microbial to ecosystem scales.

    Science.gov (United States)

    Maher, Damien T; Santos, Isaac R; Leuven, Jasper R F W; Oakes, Joanne M; Erler, Dirk V; Carvalho, Matheus C; Eyre, Bradley D

    2013-11-19

    Development of cavity ring-down spectroscopy (CRDS) has enabled real-time monitoring of carbon stable isotope ratios of carbon dioxide and methane in air. Here we demonstrate that CRDS can be adapted to assess aquatic carbon cycling processes from microbial to ecosystem scales. We first measured in situ isotopologue concentrations of dissolved CO2 ((12)CO2 and (13)CO2) and CH4 ((12)CH4 and (13)CH4) with CRDS via a closed loop gas equilibration device during a survey along an estuary and during a 40 h time series in a mangrove creek (ecosystem scale). A similar system was also connected to an in situ benthic chamber in a seagrass bed (community scale). Finally, a pulse-chase isotope enrichment experiment was conducted by measuring real-time release of (13)CO2 after addition of (13)C enriched phytoplankton to exposed intertidal sediments (microbial scale). Miller-Tans plots revealed complex transformation pathways and distinct isotopic source values of CO2 and CH4. Calculations of δ(13)C-DIC based on CRDS measured δ(13)C-CO2 and published fractionation factors were in excellent agreement with measured δ(13)C-DIC using isotope ratio mass spectroscopy (IRMS). The portable CRDS instrumentation used here can obtain real-time, high precision, continuous greenhouse gas data in lakes, rivers, estuaries and marine waters with less effort than conventional laboratory-based techniques. PMID:24131451

  16. Time resolved super continuum Cavity Ring-Down Spectroscopy for multicomponent gas detection; Espectroscopia de cavidade ressonante tipo Ring-Down Supercontinuum resolvida no tempo para detecao de multicomponentes gasosos

    Energy Technology Data Exchange (ETDEWEB)

    Nakaema, Walter Morinobu

    2010-07-01

    In this work, we present a variation of the technique CRDS (Cavity Ring-Down Spectroscopy) to obtain simultaneously a multicomponent absorption spectrum in a broad visible range. This new approach uses the Supercontinuum (SC) spectrum (resulting from irradiation of nonlinear media by femtosecond lasers, or simply generated by compact sources) as a light source to illuminate the cavity. In this context it is described the features of the modules assembling a MC-SC-CRDS (Multicomponent Supercontinuum Cavity Ring-Down Spectroscopy): a set of high reflectivity mirrors, the resonant cavity and the detection system. Some problems related to the multimode excitation, stray light, effective use of the dynamic range of the detector, the poor resolution of the instrument to resolve narrow absorption lines are issued. We present the absorption spectra of H{sub 2}O (polyads 4{upsilon}, 4{upsilon} + {delta}) and O{sub 2} (spin-forbidden b-X branch) measured simultaneously by this technique in the visible range and a comparison with the absorption lines based on HITRAN database is made to demonstrate the functionality of this method. (author)

  17. Detection of hydrogen cyanide from oral anaerobes by cavity ring down spectroscopy

    Science.gov (United States)

    Chen, Wen; Roslund, Kajsa; Fogarty, Christopher L.; Pussinen, Pirkko J.; Halonen, Lauri; Groop, Per-Henrik; Metsälä, Markus; Lehto, Markku

    2016-03-01

    Hydrogen cyanide (HCN) has been recognized as a potential biomarker for non-invasive diagnosis of Pseudomonas aeruginosa infection in the lung. However, the oral cavity is a dominant production site for exhaled HCN and this contribution can mask the HCN generated in the lung. It is thus important to understand the sources of HCN production in the oral cavity. By screening of oral anaerobes for HCN production, we observed that the genus of Porphyromonas, Prevotella and Fusobacterium generated low levels of HCN in vitro. This is the first study to show that oral anaerobes are capable of producing HCN in vitro. Further investigations were conducted on the species of P. gingivalis and we successfully detected HCN production (0.9–10.9 ppb) in the headspace of three P. gingivalis reference strains (ATCC 33277, W50 and OMG 434) and one clinical isolate. From P. gingivalis ATCC 33277 and W50, a strong correlation between HCN and CO2 concentrations (rs = 0.89, p < 0.001) was observed, indicating that the HCN production of P. gingivalis might be connected with the bacterial metabolic activity. These results indicate that our setup could be widely applied to the screening of in vitro HCN production by both aerobic and anaerobic bacteria.

  18. Determination of the HO2 radical in dielectric barrier discharge plasmas using near-infrared cavity ring-down spectroscopy

    International Nuclear Information System (INIS)

    The hydroperoxyl radical (HO2) plays an important role in combustion systems, atmospheric chemistry and the removal of air pollutants by non-thermal plasmas. This work reports the determination of the hydroperoxyl radical in dielectric barrier discharge plasmas via near-infrared continuous wave cavity ring-down spectroscopy. HO2 radicals were observed in discharges of HCHO/O2/H2O/N2 mixtures around 6625.7 cm-1 in the first H-OO stretching overtone, (2, 0, 0)-(0, 0, 0), of its ground electronic state X-tilde2A''. At certain discharge conditions (ac frequency of 5 kHz, peak-to-peak voltage of 6.5 kV, 1900 ppm HCHO, 20% O2, 3.5% H2O in N2, Ptotal = 30 Torr), HO2 radical concentration was determined to be 1.0 x 1013 molecules cm-3. The temporary evolution of HO2 concentration was obtained using the 'time window' method. The effects of oxygen concentration, water concentration, the discharge voltage and discharge gas pressure on the concentration of HO2 radicals have been investigated. The detection limit of our setup for the HO2 radical is ∼1 x 1011 molecules cm-3

  19. Detection of no and S-Nitrosocompounds Using Mid-Ir Cavity Ring-Down Spectroscopy

    Science.gov (United States)

    Stsiapura, Vitali; Shuali, Vincent K.; Ziegler, Angela; Lehmann, Kevin K.; Gaston, Benjamin M.

    2013-06-01

    Metabolic reactions of S-nitrosothiols have received much attention in biochemistry and medicine since S-nitrosocompounds can act not only as donors of nitric oxide (NO) in an organism but can themselves be involved in signal transduction. In the past few decades, the primary means of detecting S-nitrosocompounds in biological media has been through chemiluminescence detection of NO, a technique that limits the sensitivity to ppb levels and is not able to trace isotopologues of NO. Here we present a cw-CRD instrument for detection of NO isotopologues released from S-nitrosocompounds with a sensitivity of 27 pptv of NO in 100 torr He (after averaging of ˜400 ringdowns). A mid-IR ec-QCL laser (Daylight Solutions) is used to excite the ringdown cavity of finesse ˜10000 and probe the NO fundamental ro-vibrational band in the 5.2 - 5.3 μm range.

  20. Tritiated water detection in the 2.17 µM spectral region by cavity ring down spectroscopy

    International Nuclear Information System (INIS)

    Nuclear waste containers are intended to be stored in dedicated disposal sites. For the inside and environmental safety of the disposal sites, the tiny outgassing rates leaking out the containers are measured. Presently, the radioactive HT gas is measured by liquid scintillation. However an alternative method—cavity ring down spectroscopy, an isotopically selective laser technique based on molecular spectroscopy—is currently developed and evaluated for tritium measurement in its oxidized form, HTO. Applying this method, the number density of the gaseous HTO sample hold in the optical cavity cell, is derived from the laser beam absorption by vibrational symmetric stretching 2ν1 (R) HTO lines in the 4590 and 4600 cm−1 spectral range. To ensure a future accurate HTO measurement, the theoretical line intensities are confronted to the experiment: two tritiated water standards are measured with a dedicated CRDS set-up. Compared to the theoretical database, the line positions are correct (−0.067 to −0.128 cm−1), their relative intensities are in agreement with the database, but their absolute intensities are 20% weaker. Among the seven intense lines, the 4596.485 cm−1 line (intensity 8.22 10−22 cm/molecule) and the 4592.407 cm−1 line (intensity 9.83 10−22 cm/molecule) are isolated and intense for a sensitive detection. The HTO detection limit with the present set-up is 3 kBq (10 min), equivalent to 1.8 1012 molecules in the 111 cm3 CRDS cell. This detection limit could be improved by a factor 3 by reducing the detection noise

  1. Simultaneous and continuous multiple wavelength absorption spectroscopy on nanoliter volumes based on frequency-division multiplexing fiber-loop cavity ring-down spectroscopy.

    Science.gov (United States)

    Waechter, Helen; Munzke, Dorit; Jang, Angela; Loock, Hans-Peter

    2011-04-01

    We demonstrate a method for measuring optical loss simultaneously at multiple wavelengths with cavity ring-down spectroscopy (CRD). Phase-shift CRD spectroscopy is used to obtain the absorption of a sample from the phase lag of intensity modulated light that is entering and exiting an optical cavity. We performed dual-wavelength detection by using two different laser light sources and frequency-division multiplexing. Each wavelength is modulated at a separate frequency, and a broadband detector records the total signal. This signal is then demodulated by lock-in amplifiers at the corresponding two frequencies allowing us to obtain the phase-shift and therefore the optical loss at several wavelengths simultaneously without the use of a dispersive element. In applying this method to fiber-loop cavity ring-down spectroscopy, we achieve detection at low micromolar concentrations in a 100 nL liquid volume. Measurements at two wavelengths (405 and 810 nm) were performed simultaneously on two dyes each absorbing at mainly one of the wavelengths. The respective concentrations could be quantified independently in pure samples as well as in mixtures. No crosstalk between the two channels was observed, and a minimal detectable absorbance of 0.02 cm(-1) was achieved at 405 nm. PMID:21355542

  2. Quantification of Alkyl Nitrates in Ambient Air by Thermal Dissociation Cavity Ring-Down Spectroscopy with Preconcentration

    Science.gov (United States)

    Ye, C. Z.; Osthoff, H. D.; Taha, Y. M.; Pak, J. K.; Saowapon, M. T.

    2015-12-01

    Alkyl nitrates (AN, molecular formula RONO2) play a crucial role in the troposphere as temporary reservoirs of nitrogen oxides (NOx =NO +NO2) and by acting as chain terminators in the photochemical production of ozone. Mixing ratios of AN in ambient air are commonly quantified by gas chromatography with electron capture or mass spectrometric detection (GC-ECD or GC-MS) coupled to purge-and-trap preconcentration, usually on Tenax sorbent, to improve the detection limits. The analysis, however, is quite laborious as there are many alkyl nitrates that are low in individual abundance (often less than 1 parts-per-trillion by volume, pptv) and that exhibit different instrumental response factors. An alternative method is to determine alkyl nitrates as a sum (ΣAN) by thermal dissociation (TD) to a common fragment (NO2), which can then be quantified with a uniform response factor by optical absorption, for example by cavity ring-down spectroscopy (CRDS). However, the determination of ΣAN by TD-CRDS is hampered by its relatively high detection limits (several 100 pptv) and secondary chemistry following TD that results in both negative and positive interferences and depends on the composition of the ambient air sampled. In this work, a TD-CRDS equipped with a Tenax preconcentration unit is described. Matrix effects are minimized by desorbing the samples from the Tenax in a background of nitrogen. The performance of the instrument, in particular the recovery from the Tenax sorbent, was evaluated by sampling laboratory-generated mixtures of alkyl and peroxyacyl nitrates. Field data from a coastal site collected during the Ozone-depleting reactions in a coastal atmosphere (ORCA) campaign, which took place at the Amphitrite Point Observatory in Ucluelet, BC, from July 6 - 31, 2015, are presented. Advantages and disadvantages of the new method are discussed.

  3. Accurate measurements of carbon monoxide in humid air using the cavity ring-down spectroscopy (CRDS technique

    Directory of Open Access Journals (Sweden)

    H. Chen

    2012-09-01

    Full Text Available Accurate measurements of carbon monoxide (CO in humid air have been made using the cavity ring-down spectroscopy (CRDS technique. The measurements of CO mole fractions are determined from the strength of its spectral absorption in the near infrared region (∼1.57 μm after removing interferences from adjacent carbon dioxide (CO2 and water vapor (H2O absorption lines. Water correction functions that account for the dilution and pressure-broadening effects as well as absorption line interferences from adjacent CO2 and H2O lines have been derived for CO2 mole fractions between 360–390 ppm. The line interference corrections are independent of CO mole fractions. The dependence of the line interference correction on CO2 abundance is estimated to be approximately −0.3 ppb/100 ppm CO2 for dry mole fractions of CO. Comparisons of water correction functions from different analyzers of the same type show significant differences, making it necessary to perform instrument-specific water tests for each individual analyzer. The CRDS analyzer was flown on an aircraft in Alaska from April to November in 2011, and the accuracy of the CO measurements by the CRDS analyzer has been validated against discrete NOAA/ESRL flask sample measurements made on board the same aircraft, with a mean difference between integrated in situ and flask measurements of −0.6 ppb and a standard deviation of 2.8 ppb. Preliminary testing of CRDS instrumentation that employs new spectroscopic analysis (available since the beginning of 2012 indicates a smaller water vapor dependence than the models discussed here, but more work is necessary to fully validate the performance. The CRDS technique provides an accurate and low-maintenance method of monitoring the atmospheric dry mole fractions of CO in humid air streams.

  4. Near Infrared Cavity Ring-Down Spectroscopy for Isotopic Analyses of CH4 on Future Martian Surface Missions

    Science.gov (United States)

    Chen, Y.; Mahaffy P.; Holmes, V.; Burris, J.; Morey, P.; Lehmann, K.K.; Lollar, B. Sherwood; Lacrampe-Couloume, G.; Onstott, T.C.

    2014-01-01

    A compact Near Infrared Continuous Wave Cavity Ring-Down Spectrometer (near-IR-cw-CRDS) was developed as a candidate for future planetary surface missions. The optical cavity was made of titanium with rugged quartz windows to protect the delicate super cavity from the harsh environmental changes that it would experience during space flight and a Martian surface mission. This design assured the long-term stability of the system. The system applied three distributed feedback laser diodes (DFB-LD), two of which were tuned to the absorption line peaks of (sup 12)CH4 and (sup 13)CH4 at 6046.954 inverse centimeters and 6049.121 inverse centimeters, respectively. The third laser was tuned to a spectral-lines-free region for measuring the baseline cavity loss. The multiple laser design compensated for typical baseline drift of a CRDS system and, thus, improved the overall precision. A semiconductor optical amplifier (SOA) was used instead of an Acousto-Optic Module (AOM) to initiate the cavity ring-down events. It maintained high acquisition rates such as AOM, but consumed less power. High data acquisition rates combined with improved long-term stability yielded precise isotopic measurements in this near-IR region even though the strongest CH4 absorption line in this region is 140 times weaker than that of the strongest mid-IR absorption band. The current system has a detection limit of 1.4 times 10( sup –12) inverse centimeters for (sup 13)CH4. This limit corresponds to approximately 7 parts per trillion volume of CH4 at 100 Torrs. With no further improvements the detection limit of our current near IR-cw-CRDS at an ambient Martian pressure of approximately 6 Torrs (8 millibars) would be 0.25 parts per billion volume for one 3.3 minute long analysis.

  5. FIBER LOOP RING DOWN SPECTROSCOPY FOR TRACE CHEMICAL DETECTION

    OpenAIRE

    Danışman, M. Fatih; Esentürk, Okan; Abu Sayed, Md.; Yolalmaz, Alim

    2015-01-01

    Fiber loop ring down (FLRD) spectroscopy is a technique that combines high sensitivity of cavity ring down spectroscopy and elasticity of fiber optic cables. FLRD is a time domain technique that measures optical losses of a light pulse in a fiber loop. In FLRD spectroscopy, detection of a sample is performed by measurement of leaking light at each round trip within an optical cavity. Intensity of leaking light has an exponential decay where it is reduced by absorption of sample and scattering...

  6. Continuous Flow - Cavity RingDown Spectroscopy Using a Novel Universal Interface for High-Precision Bulk 13C Analysis

    Science.gov (United States)

    Saad, Nabil; Richman, Bruce

    2010-05-01

    We have developed the world's first optical spectroscopy-based system for bulk stable isotope analysis of 13C. The system is based on a novel universal interface, named LIAISON, capable of coupling to almost any CO2-generating sample preparation front-end ranging from an elemental analyzer to any dissolved carbon analysis module, which are of significant use in geochemical, ecological and food authentication studies. In one specific application, we have coupled LIAISON to an elemental analyzer (EA) and to a cavity ring-down spectrometer (CRDS) for 13C isotopic analysis of adulterated honey samples. Another application was developed to analyze dissolved inorganic carbon in water samples. LIAISON is suited for handling a high-throughput sample analysis process by running three different gas handling operations in parallel: Admitting combustion gas from the EA into a first gas bellows, analyzing the previous sample collected into a second gas bellows with CRDS, and flushing and purging a third gas bellows in preparation for the upcoming sample collection operation. The sample-to-sample analysis time is 10 minutes and the operation is completely automated for the whole front-end auto-sampler tray capacity, requiring no operator intervention. The CRDS data are collected, tabulated and saved into an output text file. The memory effect between the USGS L-Glutamic acid standard at natural abundance and the moderately enriched USGS L-Glutamic acid standard is excluded by the selection of the adequate number and duration of flush and purge cycles of the gas sample bags. The system's proven accuracy was cross-checked with EA-IRMS and its achieved precision was typically less than 0.2 permil, including the 13C-enriched tested samples. The LIAISON-CRDS system presented here provides a fully automated solution for 13C bulk stable isotope analysis with unprecedented ease-of-use and possible field portability and application with the availability of a compact front-end. In

  7. The 4-0 band of carbon monoxide by high sensitivity Cavity Ring Down spectroscopy near 8200 cm−1

    International Nuclear Information System (INIS)

    The room temperature spectrum of carbon monoxide in natural isotopic abundance is recorded by Cavity Ring Down Spectroscopy between 8094 and 8317 cm−1. The investigated range covers the low frequency region of the third overtone band centered at 8414 cm−1. The achieved sensitivity of the recordings corresponds to a noise equivalent absorption, αmin~5×10–12 cm−1. 94 transitions are measured with intensity ranging between 3×10–27 and 1×10–30 cm/molecule. They include the first observation of (i) high J lines of the P branch of the 4-0 band of 12C16O, (ii) the 4-0 band of 13C16O and 12C18O present in natural abundance in the sample (35 and 38 transitions, respectively), (iii) a few lines of the 4-0 band of 12C17O and of the 5-1 hot band of 12C16O. The spectroscopic parameters of the v=4 upper level of 13C16O and 12C18O are obtained from a fit of the measured line positions. The line positions reported with an accuracy of 5×10−4 cm−1 and the derived line intensities are used for comparison to various theoretical line lists of carbon monoxide available in the literature. The agreement between the obtained experimental data and the most recent theoretical line lists available in the literature is discussed. - Highlights: • Detection of 94 transitions of the 4-0 band of CO between 8094 and 8317 cm−1. • CRDS spectra recorded at room temperature and low pressure (5 and 10 Torr). • The noise equivalent absorption of the spectra is αmin≈5×10−12 cm−1. • First observation of the 4-0 band of 13C16O, 12C18O and 12C17O. • Critical comparison to the available calculated line lists of carbon monoxide

  8. CW-Cavity Ring Down Spectroscopy of deuterated water in the 1.58 μm atmospheric transparency window

    International Nuclear Information System (INIS)

    The spectrum of water vapour enriched in deuterium has been recorded by highly sensitive CW-Cavity Ring Down Spectroscopy in the 5855–6802 cm−1 spectral region. The studied region includes the 1.58 µm atmospheric transparency window of particular interest for remote sensing. More than 8000 absorption lines belonging to eight water isotopologues – H216O, H218O HD16O, D216O, HD18O, D218O, HD17O and D217O – were identified. The spectrum was assigned using both the IUPAC database of experimental transitions and energy levels, and accurate variational calculations. Overall, 1396 and 1277 experimental energy levels belonging to 18 and 16 upper vibrational states were retrieved for the HD16O and D216O species, respectively. 773 energy levels are newly derived. New experimental information concerns the high J (up to 20) and high Ka (up to 12) energy levels of the (101), (021), (040), (210), (120) states of HD16O and of the (111), (031), (210), (012), (130) states of D216O. While only a few energy levels were available, the rotational structure of the (130) and (220) states of HD16O could be analysed in detail. Rotational sublevels of the (140) state of D216O are reported for the first time. A detailed comparison of the derived energy levels with the values recommended by an IUPAC task group is presented. In particular, a significant improvement is evidenced for a number of quasi degenerate energy levels of HD16O. The obtained results are also discussed in relation with several recent studies. - Highlights: • The CRDS spectrum of deuterated water is recorded between 5855 and 6802 cm−1. • In the studied region, HDO contributes importantly to the spectrum of natural water. • More than 8000 lines were assigned to eight water isotopologues. • 773 energy levels are newly derived for HD16O and D216O. • The results are compared to the energy levels recommended by the IUPAC task group

  9. Accurate measurements of carbon monoxide in humid air using the cavity ring-down spectroscopy (CRDS technique

    Directory of Open Access Journals (Sweden)

    H. Chen

    2013-04-01

    Full Text Available Accurate measurements of carbon monoxide (CO in humid air have been made using the cavity ring-down spectroscopy (CRDS technique. The measurements of CO mole fractions are determined from the strength of its spectral absorption in the near-infrared region (~1.57 μm after removing interferences from adjacent carbon dioxide (CO2 and water vapor (H2O absorption lines. Water correction functions that account for the dilution and pressure-broadening effects as well as absorption line interferences from adjacent CO2 and H2O lines have been derived for CO2 mole fractions between 360–390 ppm and for reported H2O mole fractions between 0–4%. The line interference corrections are independent of CO mole fractions. The dependence of the line interference correction on CO2 abundance is estimated to be approximately −0.3 ppb/100 ppm CO2 for dry mole fractions of CO. Comparisons of water correction functions from different analyzers of the same type show significant differences, making it necessary to perform instrument-specific water tests for each individual analyzer. The CRDS analyzer was flown on an aircraft in Alaska from April to November in 2011, and the accuracy of the CO measurements by the CRDS analyzer has been validated against discrete NOAA/ESRL flask sample measurements made on board the same aircraft, with a mean difference between integrated in situ and flask measurements of −0.6 ppb and a standard deviation of 2.8 ppb. Preliminary testing of CRDS instrumentation that employs improved spectroscopic model functions for CO2, H2O, and CO to fit the raw spectral data (available since the beginning of 2012 indicates a smaller water vapor dependence than the models discussed here, but more work is necessary to fully validate the performance. The CRDS technique provides an accurate and low-maintenance method of monitoring the atmospheric dry mole fractions of CO in humid air streams.

  10. Spectral line-shapes of oxygen B-band transitions measured with cavity ring-down spectroscopy

    International Nuclear Information System (INIS)

    Results of line-shape measurements of self- and N2-broadened P9 P9 transition of the oxygen B band are presented. Spectra were acquired using the optical frequency comb- assisted Pound-Drever-Hall-locked frequency-stabilized cavity ring-down spectrometer (PDH- locked FS-CRDS). In the line-shape analysis the line narrowing described by Dicke narrowing or/and the speed dependence of collisional broadening were taken into account. The multispectrum fitting technique was used to minimize numerical correlations between line-shape parameters. Collisional broadening and shifting coefficients are reported with sub-percent uncertainties. Influence of the spectral line-shape model used in data analysis on determined line intensities and collisional broadening is discussed

  11. Cavity ring-down spectroscopy of the 6ν3 bands of 15N substituted N2O

    International Nuclear Information System (INIS)

    The 6ν3 and ν2+6ν3-ν2 bands of 15N substituted nitrous oxide isotopologues have been recorded by a continuous-wave cavity ring-down spectrometer (CW-CRDS) operated near 0.8μm. The sensitivity limit was at the level of 1x10-10/cm. In total, 213, 86 and 191 transitions were observed for the 14N15N16O, 15N14N16O and 15N216O isotopologues, respectively. The ro-vibrational spectroscopic parameters of the upper states are determined from least square fitting of the transitions. The absolute line intensities of the 6ν3 cold bands have been retrieved by a multi-line fitting procedure from the spectra with an estimated accuracy of 4% for majority of the unblended lines. The vibrational transition dipole moment squared values and the empirical Herman-Wallis coefficients are also presented.

  12. Line-shape study of self-broadened O2 transitions measured by Pound-Drever-Hall-locked frequency-stabilized cavity ring-down spectroscopy

    International Nuclear Information System (INIS)

    We present high-sensitivity and high-spectral-resolution line-shape and line-intensity measurements of self-broadened O2 b 1Σg+(v=1)(leftarrow)X 3Σg-(v=0) band transitions measured using the Pound-Drever-Hall-locked frequency-stabilized cavity ring-down spectroscopy technique. We give collisional broadening parameters and take into account the line-narrowing effects described by Dicke narrowing or the speed dependence of collisional broadening. We compare line intensities measured with relative uncertainties below 0.4% to data available in the HITRAN spectroscopic database.

  13. Miniaturized cavity ring-down detection in a liquid flow cell

    NARCIS (Netherlands)

    Bahnev, B.; Sneppen, van der L.; Wiskerke, A.E.; Ariese, F.; Gooijer, C.; Ubachs, W.M.G.

    2005-01-01

    A novel method for applying cavity ring-down spectroscopy in the liquid phase, compatible with LC analyses, is presented. The core of the setup is a home-built cavity ring-down flow cell (cell volume 12 muL) that is constructed using a silicon rubber spacer, which is clamped leak-tight between two h

  14. Applications of cavity ring-down spectroscopy to high precision isotope ratio measurement of 13C/12C in carbon dioxide.

    Science.gov (United States)

    Wahl, Ed H; Fidric, Bernard; Rella, Chris W; Koulikov, Sergei; Kharlamov, Boris; Tan, Sze; Kachanov, Alexander A; Richman, Bruce A; Crosson, Eric R; Paldus, Barbara A; Kalaskar, Shashi; Bowling, David R

    2006-03-01

    Recent measurements of carbon isotopes in carbon dioxide using near-infrared, diode-laser-based cavity ring-down spectroscopy (CRDS) are presented. The CRDS system achieved good precision, often better than 0.2 per thousand, for 4% CO2 concentrations, and also achieved 0.15-0.25 per thousand precision in a 78 min measurement time with cryotrap-based pre-concentration of ambient CO2 concentrations (360 ppmv). These results were obtained with a CRDS system possessing a data rate of 40 ring-downs per second and a loss measurement of 4.0 x 10(-11) cm(-1) Hz(-1/2). Subsequently, the measurement time has been reduced to under 10 min. This standard of performance would enable a variety of high concentration (3-10%) isotopic measurements, such as medical human breath analysis or animal breath experiments. The extension of this ring-down to the 2 microm region would enable isotopic analysis at ambient concentrations, which, combined with the small size, robust design, and potential for frequent measurements at a remote site, make CRDS technology attractive for remote atmospheric measurement applications. PMID:16500752

  15. [INVITED] New advances in fiber cavity ring-down technology

    Science.gov (United States)

    Silva, S. O.; Magalhães, R.; Marques, M. B.; Frazão, O.

    2016-04-01

    A brief review in the cavity ring-down technique (CRD) is presented. In this review, there will only be considered the conventional fiber CRD configuration, i.e., there will only be presented researches involving cavities with two couplers with 99:1 ratios, due to the large amount of publications involving this spectroscopy method. The presented survey is divided in different topics related to the measurement of physical parameters, such as strain and temperature, curvature, pressure, refractive index, gas and biochemical sensing.

  16. Cavity ring-down spectroscopy for detection in liquid chromatography at UV wavelengths using standard cuvettes in a normal incidence geometry.

    Science.gov (United States)

    van der Sneppen, L; Ariese, F; Gooijer, C; Ubachs, W

    2007-05-01

    Liquid chromatography (LC) with cavity ring-down spectroscopy (CRDS) detection, using flow cuvettes (put under normal incidence inside the ring-down cavity), is demonstrated. Fresnel reflections are maintained within the capture range of a stable cavity of 4 cm length. This method circumvents the need for specific Brewster's angles and possible mirror degradation is avoided. The flow cuvettes are commercially available at low cost. At 355 nm (the frequency-tripled output of a Nd:YAG laser), the system surpasses the performance of conventional absorbance detectors; the baseline noise was 1.3 x 10(-5)AU and detection limits (injected concentrations) were between 40 and 80 nM for nitro-polyaromatic hydrocarbons with an extinction coefficient epsilon of 7.3-10.2 x 10(3)M(-1)cm(-1). The system was also tested at 273 nm, but in the deep UV the reflectivity of the currently best available mirrors (R>or=99.91%) is still too low to show a significant improvement as compared to conventional UV-vis detection. PMID:17383664

  17. High sensitivity Cavity Ring Down spectroscopy of carbon dioxide in the 1.19–1.26 µm region

    International Nuclear Information System (INIS)

    A Cavity Ring Down spectrometer using a fiber-connected External Cavity Diode Laser (ECDL) as light source has been developed to access the 1.26–1.19 μm region. We present here the first application of this newly developed CW-CRDS spectrometer to the study of the highly sensitive spectrum of natural carbon dioxide between 7909 and 8370 cm−1. The spectrum is dominated by the ν1+3ν3 dyad at 8192.55 and 8293.95 cm−1 which forms the low energy border of the 1.2 µm transparency window of importance for planetary applications. The achieved sensitivity (noise equivalent absorption, αmin, in the 10−10–10−11 cm−1 range) allowed detection of numerous new transitions with intensity values down to 10−30 cm/molecule, in particular hot bands reaching upper states with energy up to about 10,600 cm−1. More than 3400 transitions belonging to the six major isotopologues of ‘natural’ carbon dioxide were assigned using the predictions of effective Hamiltonian (EH) models. A total of 2027, 442, 548, 303, 92 and 13 transitions belonging to 37, 9, 8, 4, 2 and 1 bands were rovibrationnally assigned for 12C16O2, 13C16O2, 16O12C18O, 16O12C17O, 16O13C18O and 16O13C17O, respectively. For comparison, only 14 12C16O2 absorption bands were previously known in the region (mostly from Venus spectra). Intensity values range between 2.1×10−30 and 2.4×10−24 cm/molecule. All the identified bands correspond to the ΔP=11 series of transitions, where P=2V1+V2+3V3 is the polyad number (Vi are vibrational quantum numbers). The overall agreement of the EH predicted and measured line positions is very good (for instance, average and rms deviations of 0.64×10−3 and 3.8×10−3 cm−1 for 12C16O2, respectively). The band-by-band analysis provided accurate spectroscopic parameters of 57 bands from a fit of the measured line positions. The global fits of the obtained intensity values of the ΔP=11 series of transitions were used to refine the corresponding set of effective

  18. I2 molecular elimination in single-photon dissociation of CH2I2 at 248 nm by using cavity ring-down absorption spectroscopy

    International Nuclear Information System (INIS)

    Following single-photon dissociation of CH2I2 at 248 nm, I2 molecular elimination is detected by using cavity ring-down absorption spectroscopy. The technique comprises two laser beams propagating in a perpendicular configuration, in which a tunable laser beam along the axis of the ring-down cell probes the I2 fragment in the B 3Πou+- X 1Σg+ transition. The nascent vibrational populations for v = 0, 1, and 2 levels are obtained with a population ratio of 1:(0.65 ± 0.10):(0.30 ± 0.05), corresponding to a Boltzmann-like vibrational temperature of 544 ± 73 K. The quantum yield of the ground state I2 elimination reaction is determined to be 0.0040 ± 0.0025. With the aid of ab initio potential energy calculations, the pathway of molecular elimination is proposed on the energetic ground state CH2I2 via internal conversion, followed by asynchronous three-center dissociation. A positive temperature effect supports the proposed mechanism.

  19. Br2 molecular elimination in photolysis of (COBr)2 at 248 nm by using cavity ring-down absorption spectroscopy: A photodissociation channel being ignored

    International Nuclear Information System (INIS)

    A primary dissociation channel of Br2 elimination is detected following a single-photon absorption of (COBr)2 at 248 nm by using cavity ring-down absorption spectroscopy. The technique contains two laser beams propagating in a perpendicular configuration. The tunable laser beam along the axis of the ring-down cell probes the Br2 fragment in the B3Πou+-X1Σg+ transition. The measurements of laser energy- and pressure-dependence and addition of a Br scavenger are further carried out to rule out the probability of Br2 contribution from a secondary reaction. By means of spectral simulation, the ratio of nascent vibrational population for v = 0, 1, and 2 levels is evaluated to be 1:(0.65 ± 0.09):(0.34 ± 0.07), corresponding to a Boltzmann vibrational temperature of 893 ± 31 K. The quantum yield of the ground state Br2 elimination reaction is determined to be 0.11 ± 0.06. With the aid of ab initio potential energy calculations, the pathway of molecular elimination is proposed on the energetic ground state (COBr)2 via internal conversion. A four-center dissociation mechanism is followed synchronously or sequentially yielding three fragments of Br2+ 2CO. The resulting Br2 is anticipated to be vibrationally hot. The measurement of a positive temperature effect supports the proposed mechanism.

  20. Comprehensive laboratory and field testing of cavity ring-down spectroscopy analyzers measuring H2O, CO2, CH4 and CO

    Science.gov (United States)

    Yver Kwok, C.; Laurent, O.; Guemri, A.; Philippon, C.; Wastine, B.; Rella, C. W.; Vuillemin, C.; Truong, F.; Delmotte, M.; Kazan, V.; Darding, M.; Lebègue, B.; Kaiser, C.; Xueref-Rémy, I.; Ramonet, M.

    2015-09-01

    To develop an accurate measurement network of greenhouse gases, instruments in the field need to be stable and precise and thus require infrequent calibrations and a low consumption of consumables. For about 10 years, cavity ring-down spectroscopy (CRDS) analyzers have been available that meet these stringent requirements for precision and stability. Here, we present the results of tests of CRDS instruments in the laboratory (47 instruments) and in the field (15 instruments). The precision and stability of the measurements are studied. We demonstrate that, thanks to rigorous testing, newer models generally perform better than older models, especially in terms of reproducibility between instruments. In the field, we see the importance of individual diagnostics during the installation phase, and we show the value of calibration and target gases that assess the quality of the data. Finally, we formulate recommendations for use of these analyzers in the field.

  1. Active control of the Pound–Drever–Hall error signal offset in high-repetition-rate cavity ring-down spectroscopy

    International Nuclear Information System (INIS)

    A new approach to realizing the Pound–Drever–Hall (PDH) error signal offset correction is presented. The proposed setup and correction procedure allow one to control not only the effect of amplitude modulation of the error signal, but also other sources of offsets that are present in the PDH feedback loop. This technique significantly improves laser frequency locking in high-repetition-rate cavity ring-down spectroscopy (CRDS) by allowing one to recover a tight PDH lock within 1 ms after switching off the probe laser beam. We apply the PDH error signal offset correction to CRDS measurements of the weak 16O2 B-band R7 Q8 line. The resulting spectra taken at a pressure of 1.2 kPa had a signal-to-noise ratio of ∼8000:1

  2. Note: Reliable, robust measurement system for trace moisture in gas at parts-per-trillion levels using cavity ring-down spectroscopy

    Science.gov (United States)

    Abe, Hisashi; Lisak, Daniel; Cygan, Agata; Ciuryło, Roman

    2015-10-01

    We report a simple, robust cavity ring-down spectroscopy system to reliably measure trace moisture in gases at parts-per-trillion (ppt) levels. The performance of the system was evaluated on the basis of experiments performed in a manner traceable to the International System of Units. The obtained result was in good agreement with the primary trace-moisture standard at 12 nmol/mol (12 ppb) in N2 in amount-of-substance fraction. Measurement capability of residual moisture in high-purity dry N2 at ˜130 pmol/mol (130 ppt) was demonstrated, and background noise of 5.3 × 10-12 cm-1 was attained, corresponding to a minimum detectable H2O of 5 pmol/mol (5 ppt).

  3. Analysis of δ18O and δ2H of fluid inclusion water in speleothems using cavity ring-down spectroscopy

    Science.gov (United States)

    Arienzo, M. M.; Swart, P. K.; Schroeder, C.; Hsiao, G.; Vonhof, H. B.

    2012-12-01

    Fluid inclusion isotope analysis is the analysis of microscopic, water filled cavities in speleothems. These cavities preserve drip water at the time of formation and fluid inclusions isotopic analysis provides information on the formation water (δ18Ow) and temperature can be calculated. The determination of δ18Ow and temperature is valuable for paleoclimate reconstructions. Recent work on speleothem fluid inclusions has utilized continuous-flow isotopic ratio mass spectrometry (IRMS) methods for determination of δ18Ow and δ2H of fluid inclusion water (Vonhof et al., Rapid. Comm. Mass Spec., 20:2553-2558, 2006; Dublyansky, and Spotl, Rapid. Comm. Mass Spec., 23: 2605-2613, 2009). Here we present a new technique utilizing cavity-ring down spectroscopy (CRDS) for δ18O and δ2H analysis of fluid inclusions and compare the data obtained to that measured on the Amsterdam Device which is a crusher system linked with an IRMS developed at the VU University Amsterdam. The extraction line at the University of Miami is an in-line system directly interfaced with the Picarro CRDS isotopic water analyzer and the design of the line is similar to the Amsterdam Device. The extraction line consists of a crusher device which is a modified valve unit, a septum port for the direct injection of water and a water trap. The CRDS technique is based on using a near infrared laser which is scanned over the H2O spectral range and by measuring the absorption spectra by ring-down, isotopic abundances are determined. This system has the potential for greater precision measurements than traditional IRMS systems. Therefore for fluid inclusion analysis, CRDS may prove to be an alternative to IRMS.

  4. Miniaturized cavity ring-down detection in a liquid flow cell

    OpenAIRE

    Bahnev, B.; Sneppen, van der, L.; Wiskerke, A.E.; Ariese, F.; Gooijer, C; Ubachs, W.M.G.

    2005-01-01

    A novel method for applying cavity ring-down spectroscopy in the liquid phase, compatible with LC analyses, is presented. The core of the setup is a home-built cavity ring-down flow cell (cell volume 12 muL) that is constructed using a silicon rubber spacer, which is clamped leak-tight between two high-reflectivity mirrors. The mirrors are in direct contact with the liquid flow, which provides for a small path length and short ring-down times. Inside the cavity there are no windows, reflectio...

  5. A sensitive and versatile detector for atmospheric NO2 and NOx based on blue diode laser cavity ring-down spectroscopy.

    Science.gov (United States)

    Fuchs, Hendrik; Dubé, William P; Lerner, Brian M; Wagner, Nicholas L; Williams, Eric J; Brown, Steven S

    2009-10-15

    A sensitive, small detector was developed for atmospheric NO2 and NOx concentration measurements. NO2 is directly detected by laser diode based cavity ring-down spectroscopy (CRDS) at 404 nm. The sum of NO and NO2 (=NOx) is simultaneously measured in a second cavity by quantitative conversion of ambient NO to NO2 in excess ozone. Interferences due to absorption by other trace gases at 404 nm, such as ozone and water vapor, are either negligible or small and are easily quantified. The limit of detection is 22 pptv (2sigma precision) for NO2 at 1 s time resolution. The conversion efficiency of NO to NO2 is 99% in excess O3. The accuracy of the NO2 measurement is mainly limited by the NO2 absorption cross section to +/-3%. Because of the formation of undetectable higher nitrogen oxides in subsequent reactions of NO2 with ozone in the NOx channel, the (1sigma) accuracy of the NOx measurement is increased to approximately +/-5% depending on the level of NOx. The new instrument was designed to be easily deployed in the field with respect to size, weight and consumables. Measurements were validated against a photolysis/chemiluminescence detector during six days of sampling ambient air with colocated inlets. The data sets for NO2, NO and NOx exhibit high correlation and good agreement within the combined accuracies of both methods. Linear fits for all three species give similar slopes of 0.99 in ambient air. PMID:19921901

  6. High-Sensitivity In-Situ Diagnosis of NO2 Production and Removal in DBD Using Cavity Ring-Down Spectroscopy

    International Nuclear Information System (INIS)

    A highly-sensitive in-situ diagnosis approach for nitrogen dioxide (NO2) has been developed in dielectric barrier discharge (DBD) based on pulsed cavity ring-down spectroscopy (CRDS). Absorption bands of NO2 in a spectral region from 508 nm to 509 nm were used, and a detection limit of 17.5 ppb was achieved. At this level of sensitivity, the quantitative and real-time monitoring of the production and removal of NO2 are accomplished for the first time in the discharge region. By measuring the removal amount and rate at different NO2 initial number densities from 1.54 × 1013 cm−3 to 2.79 × 1014 cm−3, we determined the relationship between them and NO2 initial number densities. The removal amount linearly increases with the initial number density, while the removal rate increases logarithmically. At a lower initial number density, the removal rate is limited. By considering the chemical kinetic mechanism in plasma, a qualitative explanation for the above phenomena is proposed: the additional NO2 produced by discharge limits the removal rate, since the NO2 concentration is dominated by the competition between the forward reactions (production) and the reverse reactions (removal). (plasma technology)

  7. High sensitivity cavity ring down spectroscopy of the 3ν1+3ν2+ν3 band of NO2 near 7587 cm-1

    Science.gov (United States)

    Lukashevskaya, A. A.; Naumenko, O. V.; Mondelain, D.; Kassi, S.; Campargue, A.

    2016-07-01

    The very weak 3ν1+3ν2+ν3 absorption band of the main isotopologue of nitrogen dioxide, 14N16O2, is investigated for the first time near 7587 cm-1. The absorption spectrum was recorded by high sensitivity Continuous Wave-Cavity Ring Down Spectroscopy with a noise equivalent absorption of αmin≈1×10-10 cm-1. 414 lines of the 3ν1+3ν2+ν3 band were assigned with rotational quantum numbers N and Ka as high as 32 and 6, respectively, what corresponds to 518 rotation-vibration transitions. The overall set of spin-rotation energy levels was modeled in the frame of the effective Hamiltonian approach and reproduced with an RMS of 6×10-3 cm-1 for the (obs.-calc.) deviations. The effective Hamiltonian includes interactions with three nearby dark states - (350), (062) and (312) - in Coriolis interaction with the (331) bright state. Using a selected set of experimental line intensities and the fitted values of the vibration-rotation Hamiltonian parameters, the principal parameter in the dipole moment operator expansion is determined for the 3ν1+3ν2+ν3 band. With maximum line intensity on the order of 2.5×10-27 cm/molecule at 296 K, the 3ν1+3ν2+ν3 band is the weakest band of the NO2 molecule rovibrationnally assigned so far.

  8. Molecular elimination of Br2 in photodissociation of CH2BrC(O)Br at 248 nm using cavity ring-down absorption spectroscopy

    International Nuclear Information System (INIS)

    The primary elimination channel of bromine molecule in one-photon dissociation of CH2BrC(O)Br at 248 nm is investigated using cavity ring-down absorption spectroscopy. By means of spectral simulation, the ratio of nascent vibrational population in v = 0, 1, and 2 levels is evaluated to be 1:(0.5 ± 0.1):(0.2 ± 0.1), corresponding to a Boltzmann vibrational temperature of 581 ± 45 K. The quantum yield of the ground state Br2 elimination reaction is determined to be 0.24 ± 0.08. With the aid of ab initio potential energy calculations, the obtained Br2 fragments are anticipated to dissociate on the electronic ground state, yielding vibrationally hot Br2 products. The temperature-dependence measurements support the proposed pathway via internal conversion. For comparison, the Br2 yields are obtained analogously from CH3CHBrC(O)Br and (CH3)2CBrC(O)Br to be 0.03 and 0.06, respectively. The trend of Br2 yields among the three compounds is consistent with the branching ratio evaluation by Rice-Ramsperger-Kassel-Marcus method. However, the latter result for each molecule is smaller by an order of magnitude than the yield findings. A non-statistical pathway so-called roaming process might be an alternative to the Br2 production, and its contribution might account for the underestimate of the branching ratio calculations.

  9. High-accuracy measurements of N2O concentration and isotopic composition of low and high concentration samples with small volume injections using Cavity Ring-Down Spectroscopy

    Science.gov (United States)

    Saad, Nabil; Palmer, Melissa; Huang, Kuan

    2015-04-01

    Nitrous oxide (N2O) gas is among the major contributors to global warming and ozone depletion in stratosphere. Quantitative estimate of N2O production in various pathways and N2O fluxes across different reservoirs is the key to understanding the role of N2O in the global change. To achieve this goal, accurate and concurrent measurement of both N2O concentration ([N2O]) and its associated isotopic ratios (δ 15Nα , δ 15{N}β & δ 18O) is desired. Recent developments in Cavity Ring-Down Spectroscopy (CRDS) have enabled high-precision measurements of [N2O] and Site-Preference-δ 15N (SP-δ 15N) and δ 18O of a continuous gas flow. However, many N2O samples are discrete with limited volume ( 2 ppm), and are not suitable for direct continuous measurements by CRDS. Here we present results of a small sample introduction and handling device, labelled as Small Sample Isotope Module (SSIM), coupled to and automatically coordinated with a Picarro isotopic N2O CRDS analyzer to handle and measure high concentration and/or small volume samples. The SSIM requires 20 ml of sample volume per analysis at STP, and transfers the sample to the CRDS for high-precision concentration and isotope ratio measurements. When the injected sample is

  10. Effectiveness of charged noncovalent polymer coatings against protein adsorption to silica surfaces studied by evanescent-wave cavity ring-down spectroscopy and capillary electrophoresis.

    Science.gov (United States)

    Haselberg, Rob; van der Sneppen, Lineke; Ariese, Freek; Ubachs, Wim; Gooijer, Cees; de Jong, Gerhardus J; Somsen, Govert W

    2009-12-15

    Protein adsorption to silica surfaces is a notorious problem in analytical separations. Evanescent-wave cavity ring-down spectroscopy (EW-CRDS) and capillary electrophoresis (CE) were employed to investigate the capability of positively charged polymer coatings to minimize the adsorption of basic proteins. Adsorption of cytochrome c (cyt c) to silica coated with a single layer of polybrene (PB), or a triple layer of PB, dextran sulfate (DS), and PB, was studied and compared to bare silica. Direct analysis of silica surfaces by EW-CRDS revealed that both coatings effectively reduce irreversible protein adsorption. Significant adsorption was observed only for protein concentrations above 400 microM, whereas the PB-DS-PB coating was shown to be most effective and stable. CE analyses of cyt c were performed with and without the respective coatings applied to the fused-silica capillary wall. Monitoring of the electroosmotic flow and protein peak areas indicated a strong reduction of irreversible protein adsorption by the positively charged coatings. Determination of the electrophoretic mobility and peak width of cyt c revealed reversible protein adsorption to the PB coating. It is concluded that the combination of results from EW-CRDS and CE provides highly useful information on the adsorptive characteristics of bare and coated silica surfaces toward basic proteins. PMID:19921852

  11. An Ultrahigh Precision, High-Frequency Dissolved Inorganic Carbon Analyzer Based on Dual Isotope Dilution and Cavity Ring-Down Spectroscopy.

    Science.gov (United States)

    Huang, Kuan; Cassar, Nicolas; Jonsson, Bror; Cai, Wei-jun; Bender, Michael L

    2015-07-21

    We present a novel method for continuous and automated shipboard measurements of dissolved inorganic carbon concentration ([DIC]) in surface water. The method is based on dual isotope dilution and cavity ring-down spectroscopy (DID-CRDS). In this method, seawater is continuously sampled and mixed with a flow of NaH(13)CO3 solution that is also enriched in deuterated water (the spike). The isotopic composition of CO2 (δ(13)C(spiked_sample)) derived from the DIC in the mixture, and the D/H ratio of the mixed water (δD(spiked_sample)), are measured by CRDS analyzers. The D/H of the water in the mixture allows accurate estimates of the mixing ratio of the sample and the spike. [DIC] of the sample is then calculated from the mixing ratio, [DI(13)C] of the spike, and δ(13)C(spiked_sample). In the laboratory, the precision of the method is infrared(NDIR)-based methods (mean difference = -0.9 ± 4.73 μmol kg(-1)). PMID:26119512

  12. A kinetic study of the CH2OO Criegee intermediate self-reaction, reaction with SO2 and unimolecular reaction using cavity ring-down spectroscopy.

    Science.gov (United States)

    Chhantyal-Pun, Rabi; Davey, Anthony; Shallcross, Dudley E; Percival, Carl J; Orr-Ewing, Andrew J

    2015-02-01

    Criegee intermediates are important species formed during the ozonolysis of alkenes. Reaction of stabilized Criegee intermediates with various species like SO2 and NO2 may contribute significantly to tropospheric chemistry. In the laboratory, self-reaction can be an important loss pathway for Criegee intermediates and thus needs to be characterized to obtain accurate bimolecular reaction rate coefficients. Cavity ring-down spectroscopy was used to perform kinetic measurements for various reactions of CH2OO at 293 K and under low pressure (7 to 30 Torr) conditions. For the reaction CH2OO + CH2OO (8), a rate coefficient k8 = (7.35 ± 0.63) × 10(-11) cm(3) molecule(-1) s(-1) was derived from the measured CH2OO decay rates, using an absorption cross section value reported previously. A rate coefficient of k4 = (3.80 ± 0.04) × 10(-11) cm(3) molecule(-1) s(-1) was obtained for the CH2OO + SO2 (4) reaction. An upper limit for the unimolecular CH2OO loss rate coefficient of 11.6 ± 8.0 s(-1) was deduced from studies of reaction (4). SO2 catalysed CH2OO isomerization or intersystem crossing is proposed to occur with a rate coefficient of (3.53 ± 0.32) × 10(-11) cm(3) molecule(-1) s(-1). PMID:25553776

  13. Self- and air-broadened cross sections of ethane (C2H6) determined by frequency-stabilized cavity ring-down spectroscopy near 1.68 µm

    International Nuclear Information System (INIS)

    The absorption spectrum of ethane was measured by frequency-stabilized cavity ring-down spectroscopy over the wave number range 5950–5967 cm−1. Spectra are reported for both pure ethane acquired at pressures near 3 Pa and mixtures of ethane in air at pressures ranging from 666 Pa to 101.3 kPa. Absorption cross sections are reported with a spectrum sampling period of 109 MHz and frequency resolution of 200 kHz. Atmospheric pressure cross sections agree fairly well with existing cross sections determined by FTS in nitrogen, but there are significant variations in cross sections at lower pressures. Source identification of fugitive methane emissions using spectroscopic measurements of the atmospheric ethane-to-methane ratio is also discussed. - Highlights: • We measured spectra of pure and air-broadened ethane in the 1.7 μm region. • Measured cross sections were substantially different than literature values. • Relative uncertainties of measured cross sections were less than 1 %. • These results can be used to quantify ethane/methane ratios for source apportionment

  14. Cavity ring down spectroscopy for the isotope composition measurement of water from fluid inclusion in stalagmites using heating and crushing techniques

    Science.gov (United States)

    Nakamoto, M.; Uemura, R.; Gibo, M.; Mishima, S.; Asami, R.

    2013-12-01

    Oxygen isotope record in stalagmites is useful to reconstruct past environmental changes. However, the interpretation of calcite isotope record is not straightforward because it is affected by various factors such as amount of precipitation and temperature. Water isotope composition of fluid inclusions, and oxygen isotope difference between water and host calcite, from stalagmite are potentially important proxies to estimate the paleo-temperature. Recently, infrared spectroscopy (IRIS) has been widely used for stable isotope ratio measurement of water. Unlike traditional isotope mass spectrometer (IRMS), the IRIS does not require pre-treatment processes (e.g., high-temperature furnace or equilibration device). A limitation of IRIS is that commercially available IRIS systems need large sample volume (1 - 2 micro litres) for liquid water measurement. In this study, we first developed a device suitable for measurement of smaller volume of water, and tested two extraction methods (thermal extraction and mechanical crushing). Oxygen and hydrogen isotope ratios of water were measured using cavity ring down spectroscopy (IRIS: WS-CRDS Picarro L2120-i, L2130-i). Stalagmite samples, which appear to be still growing, were collected in several caves in Okinawa, Japan. Reproducibility of a reference water (0.1 micro litres) was within 0.2 permil for δ18O and 1 permil for δD. The results showed that the IRIS is useful for small amount discrete sample. Although the δ18O value of inclusion water generally showed values resembling those of cave dripwaters, the δD value showed large depletion against that of dripwaters. The δD deviation was reduced at lower temperature extraction, suggesting that the erroneous δD values would be caused by spectral interference from organic contaminants produced by thermal decomposition.

  15. Determination of the HO{sub 2} radical in dielectric barrier discharge plasmas using near-infrared cavity ring-down spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Liu Zhongwei; Xu Yong; Yang Xuefeng; Zhu Aimin; Zhao Guoli; Wang Weiguo [Laboratory of Plasma Physical Chemistry, PO Box 288, Dalian University of Technology, Dalian 116024 (China)], E-mail: yongxu@dlut.edu.cn

    2008-02-21

    The hydroperoxyl radical (HO{sub 2}) plays an important role in combustion systems, atmospheric chemistry and the removal of air pollutants by non-thermal plasmas. This work reports the determination of the hydroperoxyl radical in dielectric barrier discharge plasmas via near-infrared continuous wave cavity ring-down spectroscopy. HO{sub 2} radicals were observed in discharges of HCHO/O{sub 2}/H{sub 2}O/N{sub 2} mixtures around 6625.7 cm{sup -1} in the first H-OO stretching overtone, (2, 0, 0)-(0, 0, 0), of its ground electronic state X-tilde{sup 2}A''. At certain discharge conditions (ac frequency of 5 kHz, peak-to-peak voltage of 6.5 kV, 1900 ppm HCHO, 20% O{sub 2}, 3.5% H{sub 2}O in N{sub 2}, P{sub total} = 30 Torr), HO{sub 2} radical concentration was determined to be 1.0 x 10{sup 13} molecules cm{sup -3}. The temporary evolution of HO{sub 2} concentration was obtained using the 'time window' method. The effects of oxygen concentration, water concentration, the discharge voltage and discharge gas pressure on the concentration of HO{sub 2} radicals have been investigated. The detection limit of our setup for the HO{sub 2} radical is {approx}1 x 10{sup 11} molecules cm{sup -3}.

  16. Measurement of Stable Isotope Ratio by Cavity Ring-Down Spectroscopy (CRDS) and the Application on Hydrology and Groundwater Geochemistry in Thailand

    International Nuclear Information System (INIS)

    The Isotope Ratio Mass Spectrometer (IRMS) is generally used in measuring the light stable isotopes. However, high investing cost and a requirement of a chemistry specialist for handling the delicate high vacuum system and complex gas equilibration methods limited its capabilities to only advanced nuclear institutions. The new approach based on near-IR laser non-dispersive Infrared absorption ''Cavity Ring-Down'' Spectroscopy (CRDS) technique introduces the advantages of stable isotope ''fingerprinting'' applications and their environmental isotopic fractionation studies. The CRDS analyzer can be operated at very high throughput with low maintenance by a non-chemist with low-cost consumable appliances. In this study, the CRDS based Isotopic Water analyzer (Picarro L2130-i) was used for δ2H and δ18O measurements of rainwater and river water samples collected from many regions in Thailand, help improving our database on stable isotopes in the local hydrological processes and providing new vision for the Local Meteoric Water Line (LMWL). The database was applied on the groundwater dynamic study and meteorological research. Furthermore, the CRDS Isotopic CO analyzer (Picarro G2101-i) was used in δ13C measurement of the Dissolved Inorganic Carbon (DIC) in groundwater in different hydrogeological setting. The limestone aquifer and Karstic groundwater system show enrich δ13C range comparing to the fractured clastic rock and the unconsolidated alluvial deposit groundwater systems. The δ13C data can be used to observe water-rock interaction and be applied in geochemical mixing model DIC for the correction of radiocarbon (14C) dating in groundwater.

  17. High-accuracy continuous airborne measurements of greenhouse gases (CO2 and CH4 using the cavity ring-down spectroscopy (CRDS technique

    Directory of Open Access Journals (Sweden)

    V. Y. Chow

    2010-03-01

    Full Text Available High-accuracy continuous measurements of greenhouse gases (CO2 and CH4 during the BARCA (Balanço Atmosférico Regional de Carbono na Amazônia phase B campaign in Brazil in May 2009 were accomplished using a newly available analyzer based on the cavity ring-down spectroscopy (CRDS technique. This analyzer was flown without a drying system or any in-flight calibration gases. Water vapor corrections associated with dilution and pressure-broadening effects for CO2 and CH4 were derived from laboratory experiments employing measurements of water vapor by the CRDS analyzer. Before the campaign, the stability of the analyzer was assessed by laboratory tests under simulated flight conditions. During the campaign, a comparison of CO2 measurements between the CRDS analyzer and a nondispersive infrared (NDIR analyzer on board the same aircraft showed a mean difference of 0.22±0.09 ppm for all flights over the Amazon rain forest. At the end of the campaign, CO2 concentrations of the synthetic calibration gases used by the NDIR analyzer were determined by the CRDS analyzer. After correcting for the isotope and the pressure-broadening effects that resulted from changes of the composition of synthetic vs. ambient air, and applying those concentrations as calibrated values of the calibration gases to reprocess the CO2 measurements made by the NDIR, the mean difference between the CRDS and the NDIR during BARCA was reduced to 0.05±0.09 ppm, with the mean standard deviation of 0.23±0.05 ppm. The results clearly show that the CRDS is sufficiently stable to be used in flight without drying the air or calibrating in flight and the water corrections are fully adequate for high-accuracy continuous airborne measurements of CO2 and CH4.

  18. Carbon isotope analysis of dissolved organic carbon in fresh and saline (NaCl) water via continuous flow cavity ring-down spectroscopy following wet chemical oxidation

    Science.gov (United States)

    Conaway, Christopher; Thomas, Randal B.; Saad, Nabil; Thordsen, James J.; Kharaka, Yousif K.

    2015-01-01

    This work examines the performance and limitations of a wet chemical oxidation carbon analyser interfaced with a cavity ring-down spectrometer (WCO-CRDS) in a continuous flow (CF) configuration for measuring δ13C of dissolved organic carbon (δ13C-DOC) in natural water samples. Low-chloride matrix (22.5 µg C/aliquot) may be analysed. The WCO-CRDS approach requires more total carbon (µg C/aliquot) than conventional CF-isotope ratio mass spectrometer, but is nonetheless applicable to a wide range of DOC concentration and water types, including brackish water, produced water, and basinal brines.

  19. Evanescent-wave cavity ring-down detection of cytochrome c on surface-modified prisms

    NARCIS (Netherlands)

    Sneppen, van der L.; Gooijer, C.; Ubachs, W.M.G.; Ariese, F.

    2009-01-01

    Adsorption kinetics and molecular interactions on different Surface interfaces are studied by means of evanescent-wave cavity ring-down spectroscopy, using total internal reflection surfaces Onto Which different self-assembled monolayers are covalently attached. The adsorption of cytochrome c (a pos

  20. Frequency-agile, rapid scanning cavity ring-down spectroscopy (FARS-CRDS) measurements of the (30012)←(00001) near-infrared carbon dioxide band

    Science.gov (United States)

    Long, D. A.; Wójtewicz, S.; Miller, C. E.; Hodges, J. T.

    2015-08-01

    We present new high accuracy measurements of the (30012)←(00001) CO2 band near 1575 nm recorded with a frequency-agile, rapid scanning cavity ring-down spectrometer. The resulting spectra were fit with the partially correlated, quadratic-speed-dependent Nelkin-Ghatak profile with line mixing. Significant differences were observed between the fitted line shape parameters and those found in existing databases, which are based upon more simplistic line profiles. Absolute transition frequencies, which were referenced to an optical frequency comb, are given, as well as the other line shape parameters needed to model this line profile. These high accuracy measurements should allow for improved atmospheric retrievals of greenhouse gas concentrations by current and future remote sensing missions.

  1. Sub-MHz accuracy measurement of the S(2) 2-0 transition frequency of D2 by Comb-Assisted Cavity Ring Down spectroscopy

    Science.gov (United States)

    Mondelain, D.; Kassi, S.; Sala, T.; Romanini, D.; Gatti, D.; Campargue, A.

    2016-08-01

    The line position of the very weak S(2) transition of deuterium in the 2-0 band has been measured with a Comb-Assisted Cavity Ring Down spectrometer. The high sensitivity spectra were recorded at 5 and 10 mbar with a Noise Equivalent Absorption, αmin, of 8 × 10-11 cm-1. The line positions at 5 and 10 mbar were measured with sub-MHz accuracy (460 and 260 kHz, respectively). After correction of the line pressure-shift, the frequency at zero pressure of the S(2) transition of the first overtone band was determined to be 187 104 299.51 ± 0.50 MHz. This value agrees within 1.7 MHz with the frequency obtained from the best available ab initio calculations and corresponds to only 15% of the claimed theoretical uncertainty.

  2. High-accuracy continuous airborne measurements of greenhouse gases (CO2 and CH4) using the cavity ring-down spectroscopy (CRDS) technique

    OpenAIRE

    H Chen; J. Winderlich; C. Gerbig; Hoefer, A.; Rella, C. W.; E. R. Crosson; Pelt, A. D.; Steinbach, J.; O. Kolle; Beck, V.; Daube, B. C.; Gottlieb, E. W.; V. Y. Chow; G. W. Santoni; Wofsy, S. C.

    2010-01-01

    High-accuracy continuous measurements of greenhouse gases (CO2 and CH4) during the BARCA (Balanço Atmosférico Regional de Carbono na Amazônia) phase B campaign in Brazil in May 2009 were accomplished using a newly available analyzer based on the cavity ring-down spectroscopy (CRDS) technique. This analyzer was flown without a drying system or any in-flight calibration gases. Water vapor corrections associated with dilution and pressure-broadening effects for CO2 and CH4 were derived from labo...

  3. Frequency-agile, rapid scanning cavity ring-down spectroscopy (FARS-CRDS) measurements of the (30012)←(00001) near-infrared carbon dioxide band

    International Nuclear Information System (INIS)

    We present new high accuracy measurements of the (30012)←(00001) CO2 band near 1575 nm recorded with a frequency-agile, rapid scanning cavity ring-down spectrometer. The resulting spectra were fit with the partially correlated, quadratic-speed-dependent Nelkin-Ghatak profile with line mixing. Significant differences were observed between the fitted line shape parameters and those found in existing databases, which are based upon more simplistic line profiles. Absolute transition frequencies, which were referenced to an optical frequency comb, are given, as well as the other line shape parameters needed to model this line profile. These high accuracy measurements should allow for improved atmospheric retrievals of greenhouse gas concentrations by current and future remote sensing missions. - Highlights: • A frequency-agile rapid scanning spectrometer was used to measure CO2. • The near-infrared (30012)←(00001) CO2 was measured. • The frequency axis was directly linked to an atomic clock. • The spectra were fit with the Hartmann-Tran profile (pCqSDNGP)

  4. Modification of Carrier Gas Stream to Improve 13C/12C Isotopic Accuracy in Cavity Ring-Down Spectroscopy-Based Measurements of Low-Concentration Dissolved Carbon Samples

    Science.gov (United States)

    Conaway, C. H.; Morkner, P.; Thomas, B.; Saad, N.

    2013-12-01

    Determining isotopic composition of dissolved organic and inorganic carbon in natural waters is of critical importance to a broad set of scientific objectives. The routine analysis of these sample types can be expensive and in the past has been limited predominantly to laboratories capable of high-precision isotope ratio mass spectrometric analysis. More recently, cavity ring-down spectroscopy (CRDS) has provided an alternative instrumental means for characterizing these samples. One challenge with these types of is that the CRDS can show a non-linear response in d13C at low carbon concentrations (<0.5 mM). Here we present a new approach using a modification of a total organic carbon-cavity ring-down spectroscopy (TOC-CRDS) continuous flow system by adding a background stream of carbon dioxide of known isotopic composition to the CRDS analytical train. The isotopic carbon values generated by the CRDS are then corrected using a two-component isotopic mixing model. This modification is useful in reducing bias towards lighter carbon isotopic values when measuring samples with low carbon concentration, such as natural waters with either dissolved organic or inorganic carbon concentrations of less than 0.5 mM, and does not introduce substantial bias for higher concentration samples.

  5. Simultaneous measurement of quality factor and wavelength shift by phase shift microcavity ring down spectroscopy

    CERN Document Server

    Cheema, M Imran; Hayat, Ahmad A; Peter, Yves-Alain; Armani, Andrea M; Kirk, Andrew G

    2012-01-01

    Optical resonant microcavities with ultra high quality factors are widely used for biosensing. Until now, the primary method of detection has been based upon tracking the resonant wavelength shift as a function of biological events. One of the sources of noise in all resonant-wavelength shift measurements is the noise due to intensity fluctuations of the laser source. An alternative approach is to track the change in the quality factor of the optical cavity by using phase shift cavity ring down spectroscopy, a technique which is insensitive to the intensity fluctuations of the laser source. Here, using biotinylated microtoroid resonant cavities, we show simultaneous measurement of the quality factor and the wavelength shift by using phase shift cavity ring down spectroscopy. These measurements were performed for disassociation phase of biotin-streptavidin reaction. We found that the disassociation curves are in good agreement with the previously published results. Hence, we demonstrate not only the applicatio...

  6. High sensitivity CW-Cavity Ring Down Spectroscopy of N2O between 6950 and 7653 cm-1 (1.44-1.31 μm): I. Line positions

    International Nuclear Information System (INIS)

    The absorption spectrum of nitrous oxide, N2O, has been recorded by CW-Cavity Ring Down Spectroscopy between 6950 and 7653 cm-1. The spectra were obtained at Doppler limited resolution using a CW-CRDS spectrometer based on a series of fibered DFB laser diodes. The typical noise equivalent absorption, in the order of αmin≈1×10-10 cm-1, allowed for the detection of lines with intensity as small as 1×10-29 cm/molecule. The positions of 7203 lines of four isotopologues (14N216O, 14N15N16O, 15N14N16O and 14N218O) were measured with a typical accuracy of 1.0×10-3 cm-1. The transitions were rovibrationally assigned on the basis of the global effective Hamiltonian models developed for each isotopologue. The band by band analysis allowed for the determination of the rovibrational parameters of more than 95 bands, most of them being newly reported while new rotational transitions are measured for the others. The measured line positions of the main isotopologue are found to be in good agreement with the predictions of the effective Hamiltonian model but a few deviations up to 0.20 cm-1 are observed. Local rovibrational perturbations were evidenced for several bands. The interaction mechanisms and the perturbers were univocally assigned on the basis of the effective Hamiltonian models.

  7. Determination of inlet transmission and conversion efficiencies for in situ measurements of the nocturnal nitrogen oxides, NO3, N2O5 and NO2, via pulsed cavity ring-down spectroscopy.

    Science.gov (United States)

    Fuchs, Hendrik; Dubé, William P; Ciciora, Steven J; Brown, Steven S

    2008-08-01

    Pulsed cavity ring-down spectroscopy is a highly sensitive method for direct absorption spectroscopy that has been applied to in situ detection of NO3, N2O5 and NO2 in the atmosphere from a variety of platforms, including ships, aircraft, and towers. In this paper, we report the development of schemes to significantly improve the accuracy of these measurements. This includes the following: (1) an overall improvement in the inlet transmission efficiencies (92 +/- 2% for NO3 and 97 +/- 1% for N2O5) achieved primarily through a reduction in the inlet residence time; and (2) the development of a calibration procedure that allows regular determination of these efficiencies in the field by addition of NO3 or N2O5 to the inlet from a portable source followed by conversion of NO3 to NO2. In addition, the dependence of the instrument's sensitivity and accuracy to a variety of conditions encountered in the field, including variations in relative humidity, aerosol loading, and VOC levels, was systematically investigated. The rate of degradation of N2O5 transmission efficiency on the inlet and filter system due to the accumulation of inorganic aerosol was determined, such that the frequency of filter changes required for accurate measurements could be defined. In the absence of aerosol, the presence of varying levels of relative humidity and reactive VOC were found to be unimportant factors in the instrument's performance. The 1 sigma accuracy of the NO3, N2O5, and NO2 measured with this instrument are -9/+12, -8/+11, +/- 6%, respectively, where the -/+ signs indicate that the actual value is low/high relative to the measurement. The largest contribution to the overall uncertainty is now due to the NO3 absorption cross section rather than the inlet transmission efficiency. PMID:18588318

  8. Molecular elimination of Br{sub 2} in photodissociation of CH{sub 2}BrC(O)Br at 248 nm using cavity ring-down absorption spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Fan He; Tsai, Po-Yu; Lin, King-Chuen [Department of Chemistry, National Taiwan University, Taipei 106, Taiwan and Institute of Atomic and Molecular Sciences, Academia Sinica, Taipei 106, Taiwan (China); Lin, Cheng-Wei; Yan, Chi-Yu; Yang, Shu-Wei; Chang, A. H. H. [Department of Chemistry, National Dong Hwa University, Shoufeng, Hualien 974, Taiwan (China)

    2012-12-07

    The primary elimination channel of bromine molecule in one-photon dissociation of CH{sub 2}BrC(O)Br at 248 nm is investigated using cavity ring-down absorption spectroscopy. By means of spectral simulation, the ratio of nascent vibrational population in v = 0, 1, and 2 levels is evaluated to be 1:(0.5 {+-} 0.1):(0.2 {+-} 0.1), corresponding to a Boltzmann vibrational temperature of 581 {+-} 45 K. The quantum yield of the ground state Br{sub 2} elimination reaction is determined to be 0.24 {+-} 0.08. With the aid of ab initio potential energy calculations, the obtained Br{sub 2} fragments are anticipated to dissociate on the electronic ground state, yielding vibrationally hot Br{sub 2} products. The temperature-dependence measurements support the proposed pathway via internal conversion. For comparison, the Br{sub 2} yields are obtained analogously from CH{sub 3}CHBrC(O)Br and (CH{sub 3}){sub 2}CBrC(O)Br to be 0.03 and 0.06, respectively. The trend of Br{sub 2} yields among the three compounds is consistent with the branching ratio evaluation by Rice-Ramsperger-Kassel-Marcus method. However, the latter result for each molecule is smaller by an order of magnitude than the yield findings. A non-statistical pathway so-called roaming process might be an alternative to the Br{sub 2} production, and its contribution might account for the underestimate of the branching ratio calculations.

  9. Measurements of water vapor isotope ratios with wavelength-scanned cavity ring-down spectroscopy technology: new insights and important caveats for deuterium excess measurements in tropical areas in comparison with isotope-ratio mass spectrometry.

    Science.gov (United States)

    Tremoy, Guillaume; Vimeux, Françoise; Cattani, Olivier; Mayaki, Salla; Souley, Ide; Favreau, Guillaume

    2011-12-15

    The new infrared laser spectroscopic techniques enable us to measure the isotopic composition (δ(18)O and δ(2)H) of atmospheric water vapor. With the objective of monitoring the isotopic composition of tropical water vapor (West Africa, South America), and to discuss deuterium excess variability (d=δ(2)H - 8δ(18)O) with an accuracy similar to measurements arising from isotope-ratio mass spectrometry (IRMS), we have conducted a number of tests and calibrations using a wavelength-scanned cavity ring-down spectroscopy (WS-CRDS) technique. We focus in this paper on four main aspects regarding (1) the tubing material, (2) the humidity calibration of the instrument, (3) the water vapor concentration effects on δ, and (4) the isotopic calibration of the instrument. First, we show that Synflex tubing strongly affects δ(2)H measurements and thus leads to unusable d values. Second, we show that the mixing ratio as measured by WS-CRDS has to be calibrated versus atmospheric mixing ratio measurements and we also suggest possible non-linear effects over the whole mixing ratio range (~2 to 20 g/kg). Third, we show that significant non-linear effects are induced by water vapor concentration variations on δ measurements, especially for mixing ratios lower than ~5 g/kg. This effect induces a 5 to 10‰ error in deuterium excess and is instrument-dependent. Finally, we show that an isotopic calibration (comparison between measured and true values of isotopic water standards) is needed to avoid errors on deuterium excess that can attain ~10‰. PMID:22095494

  10. High sensitivity CW-Cavity Ring Down Spectroscopy of five 13CO2 isotopologues of carbon dioxide in the 1.26-1.44 μm region (I): Line positions

    International Nuclear Information System (INIS)

    The absorption spectrum of highly enriched 13C carbon dioxide has been investigated by CW-Cavity Ring Down Spectroscopy with a setup based on fibered distributed feedback (DFB) laser diodes. By using a series of 30 DFB lasers, the CO2 spectrum was recorded in the 7029-7917 cm-1 region with a typical sensitivity of 3x10-10 cm-1. The uncertainty on the determined line positions is on the order of 8x10-4 cm-1. More than 3800 transitions with intensities as low as 1x10-29 cm/molecule were detected and assigned to the 13C16O2, 16O13C17O, 16O13C18O, 17O13C18O and 13C18O2 isotopologues. For comparison, only 104 line positions of 13C16O2 were previously reported in the literature in the considered region. The band-by-band analysis has led to the determination of the rovibrational parameters of a total of 83 bands including 56 bands of the 13C16O2 species. The measured line positions of 13C16O2 and 16O13C18O were found in good agreement with the predictions of the respective effective Hamiltonian (EH) models but the agreement degrades for the minor isotopologues. Several cases of resonance interactions were found and discussed. In the 20033-10002 band of 13C16O2, an anharmonic resonance interaction leads to deviations on the order of 0.05 cm-1 compared to the EH predictions. The existence of interpolyad interactions affecting the non-symmetric isotopologues of carbon dioxide is confirmed by the observation of two occurrences in 16O13C17O and 16O13C18O. The obtained results improve significantly the knowledge of the spectroscopy of the 13C isotopologues of carbon dioxide. They will be valuable to refine the sets of effective Hamiltonian parameters used to generate the CDSD database.

  11. Cavity ring-down technique for measurement of reflectivity of high reflectivity mirrors with high accuracy

    Indian Academy of Sciences (India)

    G Sridhar; Sandeep K Agarwalla; Sunita Singh; L M Gantayet

    2010-12-01

    A simple, accurate and reliable method for measuring the reflectivity of laser-grade mirrors ( > 99.5 %) based on cavity ring-down (CRD) technique has been success-fully demonstrated in our laboratory using a pulsed Nd:YAG laser. A fast photomultiplier tube with an oscilloscope was used to detect and analyse the CRD signal. The cavity decay times were measured for three cavities formed by a combination of three mirror pairs. The absolute reflectivities 1, 2, 3 were determined to be 99.94%, 99.63%, 99.52% at normal incidence. The reflectivity of mirrors is measured to an accuracy of 0.01%.

  12. Chiral cavity ring down polarimetry: Chirality and magnetometry measurements using signal reversals

    Energy Technology Data Exchange (ETDEWEB)

    Bougas, Lykourgos; Sofikitis, Dimitris; Katsoprinakis, Georgios E.; Spiliotis, Alexandros K.; Rakitzis, T. Peter, E-mail: ptr@iesl.forth.gr [Institute of Electronic Structure and Laser, Foundation for Research and Technology-Hellas, 71110 Heraklion, Crete (Greece); Department of Physics, University of Crete, 71003 Heraklion, Crete (Greece); Tzallas, Paraskevas; Loppinet, Benoit [Institute of Electronic Structure and Laser, Foundation for Research and Technology-Hellas, 71110 Heraklion, Crete (Greece)

    2015-09-14

    We present the theory and experimental details for chiral-cavity-ring-down polarimetry and magnetometry, based on ring cavities supporting counterpropagating laser beams. The optical-rotation symmetry is broken by the presence of both chiral and Faraday birefringence, giving rise to signal reversals which allow rapid background subtractions. We present the measurement of the specific rotation at 800 nm of vapors of α-pinene, 2-butanol, and α-phellandrene, the measurement of optical rotation of sucrose solutions in a flow cell, the measurement of the Verdet constant of fused silica, and measurements and theoretical treatment of evanescent-wave optical rotation at a prism surface. Therefore, these signal-enhancing and signal-reversing methods open the way for ultrasensitive polarimetry measurements in gases, liquids and solids, and at surfaces.

  13. Chiral cavity ring down polarimetry: Chirality and magnetometry measurements using signal reversals

    International Nuclear Information System (INIS)

    We present the theory and experimental details for chiral-cavity-ring-down polarimetry and magnetometry, based on ring cavities supporting counterpropagating laser beams. The optical-rotation symmetry is broken by the presence of both chiral and Faraday birefringence, giving rise to signal reversals which allow rapid background subtractions. We present the measurement of the specific rotation at 800 nm of vapors of α-pinene, 2-butanol, and α-phellandrene, the measurement of optical rotation of sucrose solutions in a flow cell, the measurement of the Verdet constant of fused silica, and measurements and theoretical treatment of evanescent-wave optical rotation at a prism surface. Therefore, these signal-enhancing and signal-reversing methods open the way for ultrasensitive polarimetry measurements in gases, liquids and solids, and at surfaces

  14. Note: An analyzer for field detection of H2S by using cavity ring-down at 1.57 μm

    Science.gov (United States)

    Siciliani de Cumis, M.; Viciani, S.; Galli, I.; Mazzotti, D.; Sorci, F.; Severi, M.; D'Amato, F.

    2015-05-01

    A prototype analyzer for the detection of hydrogen sulfide (H2S), based on cavity ring-down spectroscopy, is described. The device exploits, whenever possible, optical fibers, in order to simplify the alignment and to improve the stability. A trade-off between low detection level and simplicity has been pursued. The experimental results obtained during tests on different kinds of H2S samples are shown.

  15. Cavity-enhanced spectroscopies

    CERN Document Server

    van Zee, Roger

    2003-01-01

    ""Cavity-Enhanced Spectroscopy"" discusses the use of optical resonators and lasers to make sensitive spectroscopic measurements. This volume is written by the researcchers who pioneered these methods. The book reviews both the theory and practice behind these spectroscopic tools and discusses the scientific discoveries uncovered by these techniques. It begins with a chapter on the use of optical resonators for frequency stabilization of lasers, which is followed by in-depth chapters discussing cavity ring-down spectroscopy, frequency-modulated, cavity-enhanced spectroscopy, intracavity spectr

  16. Cavity ring-down spectrometer for high-fidelity molecular absorption measurements

    Science.gov (United States)

    Lin, H.; Reed, Z. D.; Sironneau, V. T.; Hodges, J. T.

    2015-08-01

    We present a cavity ring-down spectrometer which was developed for near-infrared measurements of laser absorption by atmospheric greenhouse gases. This system has several important attributes that make it possible to conduct broad spectral surveys and to determine line-by-line parameters with wide dynamic range, and high spectral resolution, sensitivity and accuracy. We demonstrate a noise-equivalent absorption coefficient of 4×10-12 cm-1 Hz-1/2 and a signal-to-noise ratio of 1.5×106:1 in an absorption spectrum of carbon monoxide. We also present high-resolution measurements of trace methane in air spanning more than 1.2 THz and having a frequency axing with an uncertainty less than 100 kHz. Finally, we discuss how this system enables stringent tests of advanced line shape models. To illustrate, we measured an air-broadened carbon dioxide transition over a wide pressure range and analyzed these data with a multi-spectrum fit of the partially correlated, quadratic speed-dependent Nelkin-Ghatak profile. We obtained a quality-of-fit parameter in the multispectrum fit equal to 36,000, thus quantifying small-but-measurable limitations of the model profile. This analysis showed that the line shape depends upon collisional narrowing, speed dependent effects and partial correlations between velocity- and phase-changing collisions.

  17. Flask sample measurements for CO2, CH4 and CO using cavity ring-down spectrometry

    Directory of Open Access Journals (Sweden)

    J.-L. Wang

    2013-08-01

    Full Text Available In recent years, cavity ring-down spectrometry (CRDS has been demonstrated to be a highly sensitive, stable and fast analytical technique for real-time in situ measurements of greenhouse gases. In this study, we propose the technique (which we call flask-CRDS of analyzing whole air flask samples for CO2, CH4 and CO using a custom gas manifold designed to connect to a CRDS analyzer. Extremely stable measurements of these gases can be achieved over a large pressure range in the flask, from 175 to 760 Torr. The wide pressure range is conducive to flask sample measurement in three ways: (1 flask samples can be collected in low-pressure environments (e.g. high-altitude locations; (2 flask samples can be first analyzed for other trace gases with the remaining low-pressure sample for CRDS analysis of CO2, CH4 and CO; and (3 flask samples can be archived and re-analyzed for validation. The repeatability of this method (1σ of 0.07 ppm for CO2, 0.4 ppb for CH4, and 0.5 ppb for CO was assessed by analyzing five canisters filled with the same air sample to a pressure of 200 Torr. An inter-comparison of the flask-CRDS data with in-situ CRDS measurements at a high-altitude mountain baseline station revealed excellent agreement, with differences of 0.10 ± 0.09 ppm (1σ for CO2 and 0.9 ± 1.0 ppb for CH4. This study demonstrated that the flask-CRDS method was not only simple to build and operate but could also perform highly accurate and precise measurements of atmospheric CO2, CH4 and CO in flask samples.

  18. High sensitivity Cavity Ring Down spectroscopy of 18O enriched carbon dioxide between 5850 and 7000 cm-1: Part III-Analysis and theoretical modeling of the 12C17O2, 16O12C17O, 17O12C18O, 16O13C17O and 17O13C18O spectra

    CERN Document Server

    Karlovets, E V; Mondelain, D; Kassi, S; Tashkun, S A; Perevalov, V I

    2014-01-01

    More than 19,700 transitions belonging to 11 isotopologues of carbon dioxide have been assigned in the room temperature absorption spectrum of highly 18O enriched carbon dioxide recorded by very high sensitivity CW-Cavity Ring Down spectroscopy between 5851 and 6990 cm-1 (1.71-1.43 \\mum). This third and last report is devoted to the analysis of the bands of five 17O containing isotopologues present at very low concentration in the studied spectra: 16O12C17O, 17O12C18O, 16O13C17O, 17O13C18O and 12C17O2 (627, 728, 637, 738 and 727 in short hand notation). On the basis of the predictions of effective Hamiltonian models, a total of 1759, 1786, 335, 273 and 551 transitions belonging to 24, 24, 5, 4 and 7 bands were rovibrationally assigned for 627, 728, 637, 738 and 727, respectively. For comparison, only five bands were previously measured in the region for the 728 species. All the identified bands belong to the \\deltaP=8 and 9 series of transitions, where P=2V1+V2+3V3 is the polyad number (Vi are vibrational qua...

  19. Precise oxygen and hydrogen isotope determination in nanoliter quantities of speleothem inclusion water by cavity ring-down spectroscopic techniques

    Science.gov (United States)

    Uemura, Ryu; Nakamoto, Masashi; Asami, Ryuji; Mishima, Satoru; Gibo, Masakazu; Masaka, Kosuke; Jin-Ping, Chen; Wu, Chung-Che; Chang, Yu-Wei; Shen, Chuan-Chou

    2016-01-01

    Speleothem inclusion-water isotope compositions are a promising new climatic proxy, but their applicability is limited by their low content in water and by analytical challenges. We have developed a precise and accurate isotopic technique that is based on cavity ring-down spectroscopy (CRDS). This method features a newly developed crushing apparatus, a refined sample extraction line, careful evaluation of the water/carbonate adsorption effect. After crushing chipped speleothem in a newly-developed crushing device, released inclusion water is purified and mixed with a limited amount of nitrogen gas in the extraction line for CRDS measurement. We have measured 50-260 nL of inclusion water from 77 to 286 mg of stalagmite deposits sampled from Gyokusen Cave, Okinawa Island, Japan. The small sample size requirement demonstrates that our analytical technique can offer high-resolution inclusion water-based paleoclimate reconstructions. The 1σ reproducibility for different stalagmites ranges from ±0.05 to 0.61‰ for δ18O and ±0.0 to 2.9‰ for δD. The δD vs. δ18O plot for inclusion water from modern stalagmites is consistent with the local meteoric water line. The 1000 ln α values based on calcite and fluid inclusion measurements from decades-old stalagmites are in agreement with the data from present-day farmed calcite experiment. Combination of coeval carbonate and fluid inclusion data suggests that past temperatures at 9-10 thousand years ago (ka) and 26 ka were 3.4 ± 0.7 °C and 8.2 ± 2.4 °C colder than at present, respectively.

  20. High sensitivity Cavity Ring Down spectroscopy of 18O enriched carbon dioxide between 5850 and 7000 cm−1: Part II—Analysis and theoretical modeling of the 12C18O2, 13C18O2 and 16O13C18O spectra

    International Nuclear Information System (INIS)

    More than 19000 transitions belonging to 11 isotopologues of carbon dioxide have been assigned in the room temperature absorption spectrum of highly 18O enriched carbon dioxide recorded by very high sensitivity CW-Cavity Ring Down spectroscopy between 5851 and 6990 cm−1 (1.71–1.43 μm). The line positions were determined with accuracy better than 1×10−3 cm−1 while the absolute line intensities are reported with an uncertainty better than 10%. This second report is devoted to the analysis of the bands of three multiply substituted isotopologues: 12C18O2, 13C18O2 and 16O13C18O (828, 838 and 638 in short hand notation). On the basis of the predictions of effective Hamiltonian models, a total of 2870, 538 and 1375 transitions belonging to 59, 11 and 15 bands were rovibrationnally assigned for 828, 838 and 638, respectively. For comparison, only 11 bands were previously measured by Fourier Transform spectroscopy in the region, for the 828 species. All the identified bands correspond to a ΔP=9 variation of the polyad number (P=2V1+V2+3V3, where Vi are vibrational quantum numbers). The band-by-band analysis has allowed deriving accurate spectroscopic parameters of 81 bands from a fit of the measured line positions. A few resonance perturbations were identified. In particular, the 31113 and 51106 states of 638 belonging to different polyads (P=10 and P=11, respectively) are anharmonically coupled. Using the large set of newly measured line positions and those collected from the literature, the global modeling of the line positions within the effective Hamiltonian approach was performed and a new set of Hamiltonian parameters was obtained for each of the three considered isopotologues. Using a similar approach, the global fits of the obtained intensity values of the ΔP=9 series of transitions were used to derive the corresponding ΔP=9 effective dipole moment parameters of the three considered isotopologues. The obtained results will help to improve the quality

  1. An optic fiber sensor for multiple gases based on fiber loop ring-down spectroscopy and microring resonator arrays

    Science.gov (United States)

    Zhang, Xin; Jian, Jia-wen; Zheng, Yan-gong; Jin, Han; Zou, Jie

    2016-07-01

    A high-sensitivity sensor for multiple gases based on microring array filter and fiber loop ring-down spectroscopy system is proposed and demonstrated. The parameters of the resonators are designed so that the filtered signal from a broadband light source can be tuned with an absorption spectral line of gas. Therefore, through adding microring resonators horizontally and vertically, the number of target gases and filter range are increased. In this research, in the broad spectral range of about 0.9 μm, only the absorption spectral lines of target gases are filtered. The simulation results show that three target gases, CH4, CO2 and HF, can be simultaneously detected by the sensing system. Owing to the fiber loop ring-down spectroscopy, the whole system is optimized in mini-size and sensitivity, and we can choose different sensing methods to enhance the measurement accuracy for high and low concentration conditions.

  2. A continuous stream flash evaporator for the calibration of an IR cavity ring down spectrometer for isotopic analysis of water

    CERN Document Server

    Gkinis, Vasileios; Johnsen, Sigfus J; Blunier, Thomas

    2014-01-01

    A new technique for high resolution simultaneous isotopic analysis of $\\delta^{18}\\mathrm{O}$ and $\\delta\\mathrm{D}$ in liquid water is presented. A continuous stream flash evaporator has been designed that is able to vaporise a stream of liquid water in a continuous mode and deliver a stable and finely controlled water vapour sample to a commercially available Infra Red Cavity Ring Down Spectrometer. Injection of sub $\\mu l$ amounts of the liquid water is achieved by pumping liquid water sample through a fused silica capillary and instantaneously vaporising it with a 100% efficiency in a home made oven at a temperature of $170 ^{o}$C. The system's simplicity, low power consumption and low dead volume together with the possibility for automated unattended operation, provides a solution for the calibration of laser instruments performing isotopic analysis of water vapour. Our work is mainly driven by the possibility to perform high resolution on line water isotopic analysis on Continuous Flow Analysis systems ...

  3. Portable low power cavity ring-down spectrometer for precise measurement of carbon dioxide, methane and water vapor

    Science.gov (United States)

    Fleck, Derek; Hoffnagle, John; Tan, Sze; He, Yonggang

    2016-05-01

    The necessity for monitoring of changing levels of greenhouse gases (GHGs) is clearly evident now more than ever. This has led to large deployments of analytical devices to most remote locations as well as the most densely populated regions around the world. Both large and small scale projects have forced new and old technologies to be pushed to their limits to obtain the highest performing measurements while maintaining a cost effective way to remotely monitor changes in atmospheric concentrations. In order to accomplish these strict guidelines, we present a low-power cavity ring-down spectrometer that measures Carbon Dioxide, Methane and water vapor which can achieve measurements with precisions lower than 20ppb of CO2 and 50ppt of CH4. Comparing to hundreds of watts needed in conventional CRDS design, we demonstrate that the high performance can be achieved with less than 25W. Stability of these measurements has allowed for averaging times of up to 3hr, yielding measurements of methane concentrations with precisions down to 40ppt. This is accomplished utilizing an FSR based frequency scale to determine an absolute frequency scale for these absorption features. Taking advantage of this faster, and less costly measurement technique of CRDS shows future promise with applications spanning scientific and industrial analyses, from isotopes to trace gases.

  4. Methane Fingerprinting: Isotopic Methane and Ethane-to-Methane Ratio Analysis Using a Cavity Ring-Down Spectrometer

    Science.gov (United States)

    Saad, Nabil; Fleck, Derek; Hoffnagle, John

    2016-04-01

    Emissions of Natural gas, and methane (CH4) specifically, have come under increased scrutiny by virtue of methane's 28-36x greenhouse warming potential compared to carbon dioxide (CO2) while accounting for 10% of the total greenhouse gas emissions in the US. Large uncontrolled leaks, such as the recent Aliso Canyon leak, originating from uncapped wells, coal mines and storage facilities have increased the total global contribution of methane missions even further. Determining the specific fingerprint of methane sources, by quantifying δ13C values and C2:C1 ratios, provides the means to understand methane producing processes and allows for sources of methane to be mapped and classified through these processes; i.e. biogenic vs. thermogenic, wet vs dry. In this study we present a fully developed Cavity Ring-Down Spectrometer (CRDS) that precisely measures 12CH4 concentration and its 13CH4 isotope concentration, yielding δ13C measurements, C2H6 concentration, along with CO2 and H2O. This provides real-time continuous measurements without an upfront separation requirement or multiple analyses to derive the origin of the gas samples. The highly sensitive analyzer allows for measurements of scarce molecules down to sub-ppb 1-σ precision in 5 minutes of measurement: with CH4 <0.1ppb, δ13C <1‰ C2H6 <1ppb and CO2 <1ppm. To complement this work, we provide the analysis of different methane sources providing a 2-dimensional mapping of methane sources as functions of δ13C and C2:C1 ratios, which can be thought of as a modified Bernard Plot. This dual ratio mapping can be used to discriminate between naturally occurring biogenic methane sources, naturally occurring enriched thermogenic sources, and natural gas distribution sources. This also shows future promise in aiding gas and oil exploration, in distinguishing oil vs coal gases, as well as a valuable tool in the development of methane sequestration.

  5. Magnetic field sensing based on fiber loop ring-down spectroscopy and etched fiber interacting with magnetic fluid

    Science.gov (United States)

    Wang, Qi; Liu, Xu; Zhao, Yong; Lv, Riqing; Hu, Haifeng; Li, Jin

    2015-12-01

    A novel magnetic field sensing system based on fiber loop ring-down spectroscopy (FLRDS) and etched fiber interacting with magnetic fluid (MF) is proposed and demonstrated for the first time. The enhanced evanescent field effect in the sensing part was achieved by etching the fiber with hydrofluoric acid. The influence of diameters of etched fiber to the performance of the sensor was investigated and discussed. In the sensing system, the etched fiber surrounded by MF was used as the sensing head and on account of the tunable refractive index and absorption coefficient of MF, the transmission spectrum would change with the magnetic field strength. In this letter, the FLRDS sensing system was theoretically modeled and FLRDS technique was utilized to modulate the transmission spectrum. The sensitivity of magnetic field sensing was enhanced significantly. In the experiment, performances of the magnetic field sensing system were tested by applying different measured magnetic field. The final results indicated that a sensitivity of 12.56 G/μs was achieved.

  6. A Mid-IR, Wavelength-Scanned, Cavity Ring-Down Spectrometer for Continuous Trace N2O and Nitrogen Isotope Measurements

    Science.gov (United States)

    Farinas, A. D.; Balslev-Clausen, D.; Crosson, E.

    2009-12-01

    Nitrous oxide (N2O) is an important trace atmospheric gas with both a greenhouse effect and a role in ozone depletion. The globally averaged surface abundance of N2O was 314 ppb in 1998, corresponding to a global burden of 1510 TgN. The atmospheric burden of nitrous oxide continues to increase by about 0.25%/yr. The detailed impact of N2O cannot, however, be accurately assessed or mitigated as there is currently no quantitative analysis tool for N2O (and isotopes of nitrogen) that combines the requisite precision (sub-ppbv) with the rugged simplicity, low-drift and hands-free operation necessary for real-time field studies at unattended monitoring stations. In fact, the only laboratory tool capable of delivering this sensitivity - gas chromatography - is slow, relatively complex and labor intensive. Further, the utility of in-situ atmospheric nitrogen isotope analysis is practically nonexistent due to the impracticality of using isotope ratio mass spectrometry equipment in the field. We are addressing these needs by extending the capabilities of Picarro’s wavelength-scanned, cavity ring-down spectroscopy (WS-CRDS) instrumentation to cover N2O and nitrogen isotopes. These portable gas and isotope analyzers currently utilize one or more tunable, narrowband, near-infrared lasers to provide ppbv-level detection of several gases including CO2, CH4, H2O and various isotopes. However, detection of N2O at the ppbv level requires the use of longer, mid-infrared wavelengths. The advent of compact, tunable, quantum cascade lasers (QCLs) operating at room temperature in the mid-IR has recently enabled analyzers incorporating them to reach these sensitivities. Moreover, the long effective optical path length - over 15km - of WS-CRDS and corresponding high signal-to-noise ratio inherent in this time-based measurement means that high precision can be achieved with simple thermoelectric cooling of the laser and detector. We report the performance of this first-generation WS

  7. Thermal dissociation blue diode laser ring-down spectroscopy: A novel tool for quantification of nitrogen oxide reservoir species

    Science.gov (United States)

    Osthoff, H. D.; Paul, D.; Mielke, L. H.; Furgeson, A.

    2010-12-01

    The oxides of nitrogen (NOx ≡ NO+NO2) play many important roles in the troposphere, such as the catalysis of photochemical ozone production. The lifetime of NOx in the troposphere is on the order of days; its main loss route is via conversion to HNO3 which rapidly deposits. It is now clear that the budgets of NOx are heavily influenced by nitrogen oxide reservoir species. Important nocturnal reservoir species include dinitrogen pentoxide (N2O5) and nitryl chloride (ClNO2); the important reservoir species formed during the day are relatively long-lived organic nitrates such as peroxyacyl nitrates, RC(O)O2NO2, and alkyl nitrates, RONO2. These species sequester NOx in polluted regions and re-release it, which can significantly affect ozone formation rates and air quality upon transport to regions far removed from the source. Accurate quantification of the mixing ratios of these NOx reservoir species at ambient abundance levels has been challenging, in part because organic nitrates are comprised of structurally diverse molecules in low individual abundance that are difficult to monitor by traditional techniques such as GC. In this presentation, a novel thermal dissociation cavity ring-down spectrometer for quantification of NO2, total peroxyacyl and alkyl nitrates in laboratory studies and in ambient air is described. The instrument uses a blue diode laser to monitor NO2 at 405 nm. The instrument precision (1σ) is 20 parts-per-trillion (by volume) in a 1 min average time. The organic nitrates are dissociated, and detected as, NO2 in a heated channel and quantified by difference relative to a reference channel operated at ambient temperature monitoring background NO2. The thermal dissociation of several PANs and alkyl nitrates was found to be quantitative in laboratory studies, as judged from simultaneous measurements using a commercial NOy monitor. It was also found that the amount of NO2 generated could be amplified by deliberate addition of excess NO. Sample

  8. Bulk Stable Isotope Analysis of Carbon from Solids and Liquids using an Elemental Analyzer Coupled to a Wavelength-Scanned Cavity Ring-Down Spectrophotometer

    Science.gov (United States)

    Saad, N.; Rella, C.; van Pelt, A.

    2009-04-01

    We report here on the novel employment of a small footprint Wavelength-Scanned Cavity Ring-Down Spectrometer (WS-CRDS) interfaced to an elemental analyzer for the measurement of the bulk isotopic carbon signature in plants and food products. The current system provides an inexpensive alternative with unparalleled ease-of-use as compared to standard methods using the more complex analytical instrumentation of isotope ratio mass spectrometry. A precision of carbon isotopic ratio measurements of less than 1 permil was achieved in minutes of measurement time. Such precision readily distinguishes the isotopic carbon signatures of a variety of environmental and agricultural products from different origins, providing information about food authenticity and climate changes effect on plant physiology.

  9. A two-channel thermal dissociation cavity ring-down spectrometer for the detection of ambient NO2, RO2NO2 and RONO2

    Science.gov (United States)

    Thieser, J.; Schuster, G.; Schuladen, J.; Phillips, G. J.; Reiffs, A.; Parchatka, U.; Pöhler, D.; Lelieveld, J.; Crowley, J. N.

    2016-02-01

    We describe a thermal dissociation cavity ring-down spectrometer (TD-CRDS) for measurement of ambient NO2, total peroxy nitrates (ΣPNs) and total alkyl nitrates (ΣANs). The spectrometer has two separate cavities operating at ˜ 405.2 and 408.5 nm. One cavity (reference) samples NO2 continuously from an inlet at ambient temperature, the other samples sequentially from an inlet at 473 K in which PNs are converted to NO2 or from an inlet at 723 K in which both PNs and ANs are converted to NO2, difference signals being used to derive mixing ratios of ΣPNs and ΣANs. We describe an extensive set of laboratory experiments and numerical simulations to characterise the fate of organic radicals in the hot inlets and cavity and derive correction factors to account for the bias resulting from the interaction of peroxy radicals with ambient NO and NO2. Finally, we present the first measurements and comparison with other instruments during a field campaign, outline the limitations of the present instrument and provide an outlook for future improvements.

  10. Development of a New N2O/CO Cavity Ring-Down Spectrometer for sub-ppb Ambient Gas Monitoring

    Science.gov (United States)

    Leggett, G. A.; Saad, N.; Zhou, J.; Hoffnagle, J.; Fleck, D.

    2015-12-01

    With a global warming potential of nearly 300, N2O is a critically important greenhouse gas, contributing about 5% of the US total GHG emissions. Agriculture soil management practices are the dominant source of anthropogenic N2O emissions, contributing nearly 3/4ths of US N2O emissions. In urban areas, vehicle tailpipe emissions and waste water treatment plants are significant sources of N2O. We report here a new mid-infrared laser-based cavity ring-down spectrometer that was recently developed to measure sub-ppb ambient concentrations of two key greenhouse gas species, N2O and CO, simultaneously. It combines a quantum cascade laser with a proprietary 3-mirror optical cavity. The new optical analyzer was set up to monitor nitrous oxide and carbon monoxide, along with CO2 and CH4, in ambient air obtained from a 10m tower in Santa Clara, California. In the data collected, the contribution from traffic and a nearby sewage treatment facility was evident.

  11. A new cavity ring-down instrument for airborne monitoring of N2O5, NO3, NO2 and O3 in the upper troposphere lower stratosphere

    Science.gov (United States)

    Ruth, Albert A.; Brown, Steven S.; Dinesan, Hemanth; Dubé, William P.; Goulette, Marc; Hübler, Gerhard; Orphal, Johannes; Zahn, Andreas

    2016-04-01

    The chemistry of NO3 and N2O5 is important to the regulation of both tropospheric and stratospheric ozone. In situ detection of NO3 and N2O5 in the upper troposphere lower stratosphere (UTLS) represents a new scientific direction as the only previous measurements of these species in this region of the atmosphere has been via remote sensing techniques. Because both the sources and the sinks for NO3 and N2O5 are potentially stratified spatially, their mixing ratios, and their influence on nitrogen oxide and ozone transport and loss at night can show large variability as a function of altitude. Aircraft-based measurements of heterogeneous N2O5 uptake in the lower troposphere have uncovered a surprising degree of variability in the uptake coefficient [1], but there are no corresponding high altitude measurements.The UTLS is routinely sampled by the IAGOS-CARIBIC program (Civil Aircraft for the Regular Investigation of the atmosphere Based on an Instrument Container, www.caribic-atmospheric.com), a European infrastructural program with the aim of studying the chemistry and transport across this part of the atmosphere. An airfreight container with 15 different automated instruments from 8 European research partners is utilized on board a commercial Lufthansa airbus 340-600 to monitor ~ 100 atmospheric species (trace gases and aerosol parameters) in the UTLS. The instrumentation in the CARIBIC container is now to be supplemented by a new cavity ring-down device for monitoring nitrogen oxides, jointly developed by researchers from Cork (Ireland), Boulder (USA) and Karlsruhe (Germany). The compact and light-weight instrument is designed to monitor not only NO3 and N2O5, but also NO2 and O3. The detection is based on 4 high-finesse optical cavities (cavity length ~ 44 cm). Two cavities are operated at 662 nm (maximum absorption of NO3), the other two at 405 nm (maximum absorption of NO2). The inlet to one of the (662)-cavities is heated in order to thermally decompose N2O5

  12. 光腔衰荡光谱方法探测痕量一氧化碳气体%Trace Carbon Monoxide Detection with a Cavity Ring-Down Spectrometer

    Institute of Scientific and Technical Information of China (English)

    陈兵; 周泽义; 康鹏; 刘安雯; 胡水明

    2015-01-01

    基于通讯波段的分布式反馈半导体激光器(DFB),搭建了一套光腔衰荡光谱仪(CRDS)。衰荡光腔由一对反射率高于99.997%的高反镜组成,衰荡腔长约为130 cm ,空腔衰荡时间约为150μs。当光谱平均次数达到1000次时,光谱仪灵敏度(最小可探测吸收系数)达到5×10-12 cm -1。利用热隔绝的方式稳定衰荡腔长,并使用衰荡光腔自身作为光学标准具,来标定光谱的频率:利用反馈式光谱扫描程序步进改变激光器频率,使之与衰荡腔的纵模频率逐一匹配,从而实现所测得光谱的自动标定。通过测量一氧化碳分子在1.565μm附近的吸收光谱,测定气体中一氧化碳的含量。将光谱测量结果和标准样品中的一氧化碳含量进行对比,对装置的定量精度进行了检验,表明其对一氧化碳的探测极限达4 ppbv。利用该装置对实际大气中一氧化碳的含量进行了实时监测。%A cavity ring‐down spectrometer (CRDS) was built based on telecom distributed feedback (DFB) diode lasers .The ring down cavity was formed by mirrors of 99.997% reflectivity with a separation of 130 cm ,with an empty ring down time of about 150 μs .A minimum detectable absorption coefficient of 5 × 10-12 cm -1 was obtained by averaging about 1 000 recorded spectra .The ring down cavity is thermo‐isolated ,and used as an interferometer to calibrate the recorded spectrum .A feedback control scheme was applied to step scan the laser frequency ,successively matching each of the longitudinal modes of the cavity . By measuring the CO contents in a standard gas sample ,the quantitative capability of the CRDS instrument was demonstrated , and a CO detection limit of 4 ppb was achieved .The instrument was applied to monitor the CO concentration in ambient air .

  13. Hollow waveguide cavity ringdown spectroscopy

    Science.gov (United States)

    Dreyer, Chris (Inventor); Mungas, Greg S. (Inventor)

    2012-01-01

    Laser light is confined in a hollow waveguide between two highly reflective mirrors. This waveguide cavity is used to conduct Cavity Ringdown Absorption Spectroscopy of loss mechanisms in the cavity including absorption or scattering by gases, liquid, solids, and/or optical elements.

  14. Cavity Ring-Down Spectroscopy Lite: A Low Power Analyzer for measuring Carbon Dioxide, Methane and Water Vapor

    Science.gov (United States)

    Fleck, Derek; Hoffnagle, John; Tan, Sze; He, Yonggang

    2016-04-01

    Greenhouse gas accumulation has contributed to the changes in environments across the globe. Monitoring these fluctuations on global and local scales will allow scientists to better understand contributions that are made from nature and humans. This has led to the deployment of analytical instrumentation of all types to the most remote areas as well as the most densely populated areas. This however requires instruments to be precise, versatile, robust, and most importantly have power requirements that are as not limited by location, i.e. low enough power consumption to run off of batteries or even solar array. Here we present a full greenhouse gas analyzer that utilizes a new method of CRDS to measure carbon dioxide, methane and water vapor that consumes only 25W and still maintains long term stability to allow for averaging time of over 3 hours. Measurements have a 1-σ precision of 30 ppb for CO2 and 300 ppt of CH4 with 5 minutes of averaging; and with measurements of 3 hour averages reaching precisions down to 40ppt of methane. Additionally this new flavor of CRDS has allowed for an overall increase in measurement dynamic range from traditional CW-CRDS measuring methane up to 1000ppm and carbon dioxide up to several percent. We will present supplemental data acquired using this <11 kg analyzer, including soil respirations using closed static chambers and 10m tower measurements from Santa Clara, CA.

  15. Continuous analysis of δ¹⁸O and δD values of water by diffusion sampling cavity ring-down spectrometry: a novel sampling device for unattended field monitoring of precipitation, ground and surface waters.

    Science.gov (United States)

    Munksgaard, Niels C; Wurster, Chris M; Bird, Michael I

    2011-12-30

    A novel sampling device suitable for continuous, unattended field monitoring of rapid isotopic changes in environmental waters is described. The device utilises diffusion through porous PTFE tubing to deliver water vapour continuously from a liquid water source for analysis of δ¹⁸O and δD values by Cavity Ring-Down Spectrometry (CRDS). Separation of the analysed water vapour from non-volatile dissolved and particulate contaminants in the liquid sample minimises spectral interferences associated with CRDS analyses of many aqueous samples. Comparison of isotopic data for a range of water samples analysed by Diffusion Sampling-CRDS (DS-CRDS) and Isotope Ratio Mass Spectrometry (IRMS) shows significant linear correlations between the two methods allowing for accurate standardisation of DS-CRDS data. The internal precision for an integration period of 3 min (standard deviation (SD) = 0.1‰ and 0.3‰ for δ¹⁸O and δD values, respectively) is similar to analysis of water by CRDS using an autosampler to inject and evaporate discrete water samples. The isotopic effects of variable air temperature, water vapour concentration, water pumping rate and dissolved organic content were found to be either negligible or correctable by analysis of water standards. The DS-CRDS system was used to analyse the O and H isotope composition in short-lived rain events. Other applications where finely time resolved water isotope data may be of benefit include recharge/discharge in groundwater/river systems and infiltration-related changes in cave drip water. PMID:22468325

  16. Cavity-Enhanced Frequency-Agile Rapid Scanning (fars) Spectroscopy: Measurement Principles

    Science.gov (United States)

    Hodges, Joseph T.; Long, David A.; Truong, Gar-Wing; Douglass, Kevin O.; Maxwell, Stephen E.; Zee, Roger Van; Plusquellic, David F.

    2013-06-01

    We present the principles of frequency-agile, rapid scanning (FARS) spectroscopy, a new technique for high-bandwidth, cavity-enhanced, laser absorption measurements. This method enables a visible or near-infrared probe laser beam to be frequency tuned over several tens of GHz using a microwave source, a waveguide phase modulator and a filter cavity. For the types of cavity-enhanced methods discussed here, the optical resonator itself is used to select a single sideband of the modulated laser spectrum, obviating the need for a separate filter cavity. FARS offers several important advantages over conventional cw laser tuning methods based on thermal or mechanical methods. These include, high speed tuning with sub-ms switching times, the ability to select arbitrary frequency steps or chirp rates, and the realization of a spectrum detuning axis with sub-kHz level precision. We discuss how FARS can be applied to cavity ring-down spectroscopy and other cavity-enhanced methods to enable rapid and accurate measurements of line parameters and to give noise-equivalent absorption coefficients at the 10^{-12} cm^{-1} Hz^{-1/2} level.

  17. Line-Parameter Measurements and Stringent Tests of Line-Shape Models Based on Cavity-Enhanced Absorption Spectroscopy

    Science.gov (United States)

    Bielska, Katarzyna; Fleisher, Adam J.; Hodges, Joseph T.; Lin, Hong; Long, David A.; Reed, Zachary D.; Sironneau, Vincent; Truong, Gar-Wing; Wójtewicz, Szymon

    2014-06-01

    Laser methods that are based on cavity-enhanced absorption spectroscopy (CEAS) are well-suited for measuring molecular line parameters under conditions of low optical density, and as such they are complementary to broadband Fourier-transform spectroscopy (FTS) techniques. Attributes of CEAS include relatively low detection limits, accurate and precise detuning axes and high fidelity measurements of line shape. In many cases these performance criteria are superior to those obtained using direct laser absorption spectroscopy and FTS-based systems. In this presentation we will survey several examples of frequency-stabilized cavity ring-down spectroscopy (FS-CRDS)1 measurements obtained with laser spectrometers developed at the National Institute of Standards and Technology (NIST) in Gaithersburg Maryland. These experiments, which are motivated by atmospheric monitoring and remote-sensing applications that require high-precision and accuracy, involve nearinfrared transitions of carbon dioxide, water, oxygen and methane. We discuss spectra with signal-to-noise ratios exceeding 106, frequency axes with absolute uncertainties in the 10 kHz to 100 kHz range and linked to a Cs clock, line parameters with relative uncertainties at the 0.2 % level and isotopic ratios measured with a precision of 0.03 %. We also present FS-CRDS measurements of CO2 line intensities which are measured at atmospheric concentration levels and linked to gravimetric standards for CO2 in air, and we quantify pressure-dependent deviations between various theoretical line profiles and measured line shapes. Finally we also present recent efforts to increase data throughput and spectral coverage in CEAS experiments. We describe three new high-bandwidth CEAS techniques including frequency-agile, rapid scanning spectroscopy (FARS)2, which enables continuous-wave measurements of cavity mode linewidth and acquisition of ringdown decays with no dead time during laser frequency tuning, heterodyne

  18. Carbon isotopic analysis of dissolved organic carbon in produced water brines by wet chemical oxidation and cavity ring-down spectroscopy

    Science.gov (United States)

    Thomas, B.; Conaway, C.; Kharaka, Y. K.; Saad, N.

    2012-12-01

    We have adapted the Picarro iTOC CRDS isotope analyzer for analysis of produced water brines via wet chemical persulfate oxidation. In particular, we developed strategies and techniques for overcoming the limitation imposed by low oxidation efficiencies due to the chloride ion interference with persulfate oxidation. These techniques are important for understanding the origin of dissolved organic carbon in subsurface fluids from oilfields, as a tracer of fracking fluids in groundwater, and in interpreting changes in groundwater DOC as a result of microbial activity including oil biodegradation or microbially enhanced oil recovery. We describe the limitations of this new instrument for the analysis of DOC in brines including sample requirements, matrix effects, and the effect of DOC composition on reaction efficiency and isotopic measurements. We compare strategies including anion exchange cartridges, persulfate reactant concentrations, and reaction time. The CRDS analysis of DOC in brines is a useful tool for understanding the origin and fate of DOC and is a potentially powerful tool to identifiy evidence of contamination due to hydrofracturing chemicals that have a distinctive carbon isotopic signature relative to natural brine.

  19. The theory of measuring hydroperoxyl radical by cavity ring- down spectroscopy%衰荡光谱法测量OH自由基的理论研究

    Institute of Scientific and Technical Information of China (English)

    聂劲松; 张为俊; 杨顒; 王沛; 胡欢陵

    2000-01-01

    提出了一种用衰荡光谱法测量对流层OH自由基的新方法,并从理论上推导出OH自由基浓度与衰荡时间的关系,讨论了该方法的可行性和灵敏度,分析了各种干扰因素对测量的影响,认为该方法与传统测量OH自由基的方法相比优势较为明显.

  20. Cavity-enhanced spectroscopy and sensing

    CERN Document Server

    Loock, Hans-Peter

    2014-01-01

    The book reviews the dramatic recent advances in the use of optical resonators for high sensitivity and high resolution molecular spectroscopy as well as for chemical, mechanical and physical sensing.  It encompasses a variety of cavities including those made of two or more mirrors, optical fiber loops, fiber gratings and spherical cavities. The book focuses on novel techniques and their applications. Each chapter is written by an expert and/or pioneer in the field. These experts also provide the theoretical background in optics and molecular physics where needed. Examples of recent breakthroughs include the use of frequency combs (Nobel prize 2005) for cavity enhanced sensing and spectroscopy, the use of novel cavity materials and geometries, the development of optical heterodyne detection techniques combined to active frequency-locking schemes. These methods allow the use and interrogation of optical resonators with a variety of coherent light sources for trace gas detection and sensing of strain, temperat...

  1. Performance assessment of a cavity ring-down laser spectrometer: achieving better precision and accuracy in the measurement of δ18O and δ2H in liquid water samples

    International Nuclear Information System (INIS)

    The development of new isotopic laser-based analyzers currently represents a clear alternative to conventional isotope ratio mass spectrometers. However, this analytical technique also suffers some disadvantages such as the memory effect, problems related to the overall stability of the equipment and other issues associated with the injection system, essentially regarding the syringe's longevity. This paper aims to minimize these disadvantages in order to increase the overall performance, in terms of precision and accuracy, of these kinds of analyzers. The main results of the experiments carried out in this paper have shown that: (i) the minimum number of discarded injections needed to eliminate the memory effect can be determined just considering the expected isotopic signature difference between two consecutive samples; (ii) both accuracy and precision of the isotopic measurements increase with increasing injection volume up to 2.1–2.2 µL; (iii) it is possible to extend the syringe lifetime by almost a factor of 6 by using n-methyl 2-pyrrolidone as a lubricant. Besides, it has been concluded that, by using the appropriate procedure, the main disadvantages associated with CRDS laser spectroscopy analyzers can be minimized, achieving measurement accuracy and precision of the order of ±0.05 ‰ for δ18O and ±0.3 ‰ for δ2H. (paper)

  2. Molecular Laser Spectroscopy as a Tool for Gas Analysis Applications

    OpenAIRE

    Javis Anyangwe Nwaboh; Thibault Desbois; Daniele Romanini; Detlef Schiel; Olav Werhahn

    2011-01-01

    We have used the traceable infrared laser spectrometric amount fraction measurement (TILSAM) method to perform absolute concentration measurements of molecular species using three laser spectroscopic techniques. We report results performed by tunable diode laser absorption spectroscopy (TDLAS), quantum cascade laser absorption spectroscopy (QCLAS), and cavity ring down spectroscopy (CRDS), all based on the TILSAM methodology. The measured results of the different spectroscopic techniques are ...

  3. Cavity-Enhanced Ultrafast Transient Absorption Spectroscopy

    CERN Document Server

    Reber, Melanie A R; Allison, Thomas K

    2015-01-01

    We present a new technique using a frequency comb laser and optical cavities for performing ultrafast transient absorption spectroscopy with improved sensitivity. Resonantly enhancing the probe pulses, we demonstrate a sensitivity of $\\Delta$OD $ = 1 \\times 10^{-9}/\\sqrt{\\mbox{Hz}}$ for averaging times as long as 30 s per delay point ($\\Delta$OD$_{min} = 2 \\times 10^{-10}$). Resonantly enhancing the pump pulses allows us to produce a high excitation fraction at high repetition-rate, so that signals can be recorded from samples with optical densities as low as OD $\\approx 10^{-8}$, or column densities $< 10^{10}$ molecules/cm$^2$. This high sensitivity enables new directions for ultrafast spectroscopy.

  4. [Measurement of Trace C2H6 Based on Optical-Feedback Cavity-Enhanced Absorption Spectroscopy].

    Science.gov (United States)

    Wan, Fu; Chen, Wei-gen; Gu, Zhao-liang; Zou, Jing-xin; DU, Ling-Ling; Qi, Wei; Zhou, Qu

    2015-10-01

    Ethane is one of major fault characteristic gases dissolved in power transformer, the detection of Ethane with high accuracy and sensitivity is the key of dissolved gas analysis. In this paper, based on optical feedback theory and cavity-enhanced absorption spectroscopy, combined with quantum cascade laser, a detection system for dissolved gas C2 H6 in transformer oil was built up. Based on the symmetry of the individual cavity modes, the phase matching of returning light in resonance with the cavity was achieved through LabVIEW codes. The optical feedback effect that the emitted light return to the laser cavity after a small delay time and lock to the resonance frequency of cavity, even and odd modes effect that the higher modes and lower modes structure will build up alternatively, and threshold current lowering effect of about 1.2 mA were studied and achieved. By cavity ring-down spectroscopy, the effective reflectivity of 99.978% and cavity finesse of 7 138.4 is obtained respectively. The frequency selectivity is 0.005 2 cm(-1). With an acquisition time of 1s, this optical system allows detection for the PQ3 band of C2 H6 with high accuracy of 95.72% ± 0.17% and detection limit of (1.97 ± 0.06) x 10(-3) μL x L(-1) at atmospheric pressure and temperature of 20 degrees C, which lays a foundation for fault diagnose from dissolved gas analysis. PMID:26904820

  5. Adsorption of cytochrome c to silica surfaces studied using evanescent wave broadband cavity-enhanced absorption spectroscopy

    Science.gov (United States)

    Moore, L. J.; van der Sneppen, L.; Peverall, R.; Hancock, G.; Ritchie, G. A. D.

    2010-08-01

    The adsorption of cytochrome c (cyt c) to a silica surface has been studied by use of evanescent wave broadband cavityenhanced absorption spectroscopy (EW-BBCEAS). Visible radiation from a supercontinuum source is coupled into an optical cavity consisting of a pair of broadband high reflectivity mirrors, and a total internal reflection (TIR) event at the prism/water interface. Aqueous solutions of cyt c are placed onto the TIR footprint on the prism surface and the subsequent protein adsorption is probed by the resulting evanescent wave. The time integrated cavity output is directed into a spectrometer, where it is dispersed and analysed. The high spectral brilliance of the SC affords a baseline noise comparable to evanescent wave cavity ring-down spectroscopy (EW-CRDS), and the broadband nature of the source allows observation of a wide spectral range (ca 250 nm in the visible). The system is calibrated by measuring the absorption spectra of dyes of a known absorbance. Absorption spectra of cyt c are obtained for both S and P polarized radiation, allowing information about the orientation of the adsorbed protein to be extracted.

  6. Resonant cavity spectroscopy of radical species

    Science.gov (United States)

    Ritchie, Grant

    2015-04-01

    Photo-oxidation in the troposphere is highly complex, being initiated by short lived radical species, in the daytime dominated by the hydroxyl radical, OH, with contributions from Cl atoms, and at night by either NO3 radicals or ozone. Chemical oxidation cycles, which couple OH, HO2 and peroxy (RO2) radical species, remove primary emitted trace species which are harmful to humans or to the wider environment. However, many of the secondary products produced by atmospheric photo-oxidation are also directly harmful, for example O3, NO2, acidic and multifunctional species, many of which are of low volatility and are able to partition effectively to the condensed phase, creating secondary organic aerosol (SOA), which contributes a significant fraction of tropospheric aerosol, with associated impacts on climate and human health. The accuracy of atmospheric models to predict these impacts necessarily requires accurate knowledge of the chemical oxidative cycling. Two of the simplest intermediates are the hydroperoxy radical, HO2, and the smallest and dominant organic peroxy radical, CH3O2, formed directly by the reactions of OH with CO/O2 and CH4/O2, respectively, and indirectly following the oxidation of larger VOCs. OH, HO2 and RO2 (collectively known as ROx) are rapidly cycled, being at the centre of tropospheric oxidation, and hence are some of the best targets for models to compare with field data. The reaction of HO2 and RO2 with NO constitutes the only tropospheric in-situ source of O3. Despite their importance, neither HO2 nor CH3O2 is measured directly in the atmosphere. HO2 is only measured indirectly following its conversion to OH and CH3O2 is not measured at all. Typically only the sum of RO2 radicals is measured, making no distinction between different organic peroxy radicals. This contribution will detail recent studies using (i) optical feedback cavity enhanced absorption spectroscopy with both quantum and inter-band cascade lasers in the mid-IR, and (ii

  7. Cavity-enhanced surface-plasmon resonance sensing: Modeling and performance

    Czech Academy of Sciences Publication Activity Database

    Giorgini, A.; Avino, S.; Malara, P.; Zullo, R.; Gaglio, G.; Homola, Jiří; De Natale, P.

    2014-01-01

    Roč. 25, č. 1 (2014), 015205. ISSN 0957-0233 Institutional support: RVO:67985882 Keywords : optical resonators * optical sensor s * cavity ring-down spectroscopy Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 1.433, year: 2014

  8. High sensitivity liquid phase measurements using broadband cavity enhanced absorption spectroscopy (BBCEAS) featuring a low cost webcam based prism spectrometer.

    Science.gov (United States)

    Qu, Zhechao; Engstrom, Julia; Wong, Donald; Islam, Meez; Kaminski, Clemens F

    2013-11-01

    Cavity enhanced techniques enable high sensitivity absorption measurements in the liquid phase but are typically more complex, and much more expensive, to perform than conventional absorption methods. The latter attributes have so far prevented a wide spread use of these methods in the analytical sciences. In this study we demonstrate a novel BBCEAS instrument that is sensitive, yet simple and economical to set up and operate. We use a prism spectrometer with a low cost webcam as the detector in conjunction with an optical cavity consisting of two R = 0.99 dielectric mirrors and a white light LED source for illumination. High sensitivity liquid phase measurements were made on samples contained in 1 cm quartz cuvettes placed at normal incidence to the light beam in the optical cavity. The cavity enhancement factor (CEF) with water as the solvent was determined directly by phase shift cavity ring down spectroscopy (PS-CRDS) and also by calibration with Rhodamine 6G solutions. Both methods yielded closely matching CEF values of ~60. The minimum detectable change in absorption (αmin) was determined to be 6.5 × 10(-5) cm(-1) at 527 nm and was limited only by the 8 bit resolution of the particular webcam detector used, thus offering scope for further improvement. The instrument was used to make representative measurements on dye solutions and in the determination of nitrite concentrations in a variation of the widely used Griess Assay. Limits of detection (LOD) were ~850 pM for Rhodamine 6G and 3.7 nM for nitrite, respectively. The sensitivity of the instrument compares favourably with previous cavity based liquid phase studies whilst being achieved at a small fraction of the cost hitherto reported, thus opening the door to widespread use in the community. Further means of improving sensitivity are discussed in the paper. PMID:24049768

  9. Broadband cavity-enhanced absorption spectroscopy in the ultraviolet spectral region for measurements of nitrogen dioxide and formaldehyde

    Science.gov (United States)

    Washenfelder, R. A.; Attwood, A. R.; Flores, J. M.; Zarzana, K. J.; Rudich, Y.; Brown, S. S.

    2016-01-01

    Formaldehyde (CH2O) is the most abundant aldehyde in the atmosphere, and it strongly affects photochemistry through its photolysis. We describe simultaneous measurements of CH2O and nitrogen dioxide (NO2) using broadband cavity-enhanced absorption spectroscopy in the ultraviolet spectral region. The light source consists of a continuous-wave diode laser focused into a Xenon bulb to produce a plasma that emits high-intensity, broadband light. The plasma discharge is optically filtered and coupled into a 1 m optical cavity. The reflectivity of the cavity mirrors is 0.99930 ± 0.00003 (1- reflectivity = 700 ppm loss) at 338 nm, as determined from the known Rayleigh scattering of He and zero air. This mirror reflectivity corresponds to an effective path length of 1.43 km within the 1 m cell. We measure the cavity output over the 315-350 nm spectral region using a grating monochromator and charge-coupled device array detector. We use published reference spectra with spectral fitting software to simultaneously retrieve CH2O and NO2 concentrations. Independent measurements of NO2 standard additions by broadband cavity-enhanced absorption spectroscopy and cavity ring-down spectroscopy agree within 2 % (slope for linear fit = 1.02 ± 0.03 with r2 = 0.998). Standard additions of CH2O measured by broadband cavity-enhanced absorption spectroscopy and calculated based on flow dilution are also well correlated, with r2 = 0.9998. During constant mixed additions of NO2 and CH2O, the 30 s measurement precisions (1σ) of the current configuration were 140 and 210 pptv, respectively. The current 1 min detection limit for extinction measurements at 315-350 nm provides sufficient sensitivity for measurement of trace gases in laboratory experiments and ground-based field experiments. Additionally, the instrument provides highly accurate, spectroscopically based trace gas detection that may complement higher precision techniques based on non-absolute detection methods. In addition to

  10. Magnetic field sensor using the fiber loop ring-down technique and an etched fiber coated with magnetic fluid.

    Science.gov (United States)

    Shen, Tao; Feng, Yue; Sun, Binchao; Wei, Xinlao

    2016-02-01

    The fiber loop ring-down spectroscopy technique is introduced into the evanescent-field-based sensing scheme in order to create a new type of fiber-based magnetic field sensor. As a consequence, the sensitivity and stability of the magnetic field sensing system are significantly enhanced. The sensor head is constructed using a section of a single-mode fiber with its cladding partially etched. The process of fiber etching is described in detail, and the relationship between the diameter of the etched fiber and the etching time is experimentally investigated. After adopting the appropriate size of the etched fiber, the final experimental results show that the magnetic field strength has a well-defined linear relationship with the inverse of the ring-down time τ over a range of 30 mT with a sensitivity of 95.5 ns/mT. PMID:26836067

  11. Absolute absorption and fluorescence measurements over a dynamic range of 10$^6$ with cavity-enhanced laser-induced fluorescence

    CERN Document Server

    Sanders, Scott E; Nahler, N Hendrik; Wrede, Eckart

    2013-01-01

    We describe a novel experimental setup that combines the advantages of both laser-induced fluorescence and cavity ring-down techniques. The simultaneous measurement of the ring-down and fluorescence signals from the same sample in a single laser beam delivers the calibration of the fluorescence measurement to gain absolute quantities: absorption cross section, sample density and fluorescence quantum yield. At the same time, the fluorescence measurement extends the dynamic range of a stand-alone cavity ring-down setup from typically three to at least six orders of magnitude. The methodology of this combined cavity-enhanced laser-induced fluorescence (CELIF) technique is developed and rigorously tested against the spectroscopy of 1,4-bis(phenylethynyl)benzene in a molecular beam and density measurements in a cell.

  12. Optical re-injection in cavity-enhanced absorption spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Leen, J. Brian, E-mail: b.leen@lgrinc.com; O’Keefe, Anthony [Los Gatos Research, 67 E. Evelyn Avenue, Suite 3, Mountain View, California 94041 (United States)

    2014-09-15

    Non-mode-matched cavity-enhanced absorption spectrometry (e.g., cavity ringdown spectroscopy and integrated cavity output spectroscopy) is commonly used for the ultrasensitive detection of trace gases. These techniques are attractive for their simplicity and robustness, but their performance may be limited by the reflection of light from the front mirror and the resulting low optical transmission. Although this low transmitted power can sometimes be overcome with higher power lasers and lower noise detectors (e.g., in the near-infrared), many regimes exist where the available light intensity or photodetector sensitivity limits instrument performance (e.g., in the mid-infrared). In this article, we describe a method of repeatedly re-injecting light reflected off the front mirror of the optical cavity to boost the cavity's circulating power and deliver more light to the photodetector and thus increase the signal-to-noise ratio of the absorption measurement. We model and experimentally demonstrate the method's performance using off-axis cavity ringdown spectroscopy (OA-CRDS) with a broadly tunable external cavity quantum cascade laser. The power coupled through the cavity to the detector is increased by a factor of 22.5. The cavity loss is measured with a precision of 2 × 10{sup −10} cm{sup −1}/√(Hz;) an increase of 12 times over the standard off-axis configuration without reinjection and comparable to the best reported sensitivities in the mid-infrared. Finally, the re-injected CRDS system is used to measure the spectrum of several volatile organic compounds, demonstrating the improved ability to resolve weakly absorbing spectroscopic features.

  13. Optical re-injection in cavity-enhanced absorption spectroscopy

    Science.gov (United States)

    Leen, J. Brian; O’Keefe, Anthony

    2014-01-01

    Non-mode-matched cavity-enhanced absorption spectrometry (e.g., cavity ringdown spectroscopy and integrated cavity output spectroscopy) is commonly used for the ultrasensitive detection of trace gases. These techniques are attractive for their simplicity and robustness, but their performance may be limited by the reflection of light from the front mirror and the resulting low optical transmission. Although this low transmitted power can sometimes be overcome with higher power lasers and lower noise detectors (e.g., in the near-infrared), many regimes exist where the available light intensity or photodetector sensitivity limits instrument performance (e.g., in the mid-infrared). In this article, we describe a method of repeatedly re-injecting light reflected off the front mirror of the optical cavity to boost the cavity's circulating power and deliver more light to the photodetector and thus increase the signal-to-noise ratio of the absorption measurement. We model and experimentally demonstrate the method's performance using off-axis cavity ringdown spectroscopy (OA-CRDS) with a broadly tunable external cavity quantum cascade laser. The power coupled through the cavity to the detector is increased by a factor of 22.5. The cavity loss is measured with a precision of 2 × 10−10 cm−1/\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{upgreek} \\usepackage{mathrsfs} \\setlength{\\oddsidemargin}{-69pt} \\begin{document} }{}$\\sqrt {{\\rm Hz;}}$\\end{document} Hz ; an increase of 12 times over the standard off-axis configuration without reinjection and comparable to the best reported sensitivities in the mid-infrared. Finally, the re-injected CRDS system is used to measure the spectrum of several volatile organic compounds, demonstrating the improved ability to resolve weakly absorbing spectroscopic features. PMID:25273701

  14. Real-time multiplexed digital cavity-enhanced spectroscopy

    International Nuclear Information System (INIS)

    Cavity-enhanced spectroscopy is a sensitive optical absorption technique but one where the practical applications have been limited to studying small wavelength ranges. In addition, this Letter shows that wideband operation can be achieved by combining techniques usually reserved for the communications community with that of cavity-enhanced spectroscopy, producing a multiplexed real-time cavity-enhanced spectrometer. We use multiple collinear laser sources operating asynchronously and simultaneously while being detected on a single photodetector. This is synonymous with radio frequency (RF) cellular systems in which signals are detected on a single antenna but decoded uniquely. Here, we demonstrate results with spectra of methyl salicylate and show parts-per-billion per root hertz sensitivity measured in real-time

  15. High sensitivity CW-Cavity Ring Down Spectroscopy of N2O between 6950 and 7653 cm−1 (1.44–1.31 μm): II. Line intensities

    International Nuclear Information System (INIS)

    The room temperature absorption spectra of nitrous oxide, N2O, have been recorded in the 6950–7653 cm−1 spectral region at 2 and 10 Torr using a CW-CRDS spectrometer based on 24 fibered DFB lasers. The achieved sensitivity (noise equivalent absorption αmin≈5×10–11 cm−1) allowed detecting lines with intensities as low as 1×10–29 cm/molecule. In the preceding contribution (Lu Y, Mondelain D, Liu AW, Perevalov VI, Kassi S, Campargue A, J Quant Spectros and Radiat Transfer 2012;113:749–62), we reported the assignment of more than 7200 N2O lines in the region and the derivation of the corresponding spectroscopic parameters Gv, Bv, Dv and Hv. In the present work, more than 1300 14N216O absolute line intensities of cold and hot bands belonging to the ΔP=12, 13 and 14 series of transitions have been measured (P=2V1+V2+4V3 is the polyad number). The uncertainty of the obtained line intensity values varies from 4 to 7% for the majority of the lines. The obtained dataset extends importantly the set of measurements available in the literature, in particular for the ΔP =13 series for which previous data were very limited. The ΔP=12–14 effective dipole moment parameters were fitted to the intensity values measured in this work and available in the literature. The obtained sets of the dipole moment parameters allow reproducing the observed line intensities within their experimental uncertainties. The calculated intensities of the ΔP=12, 13 and 14 bands of 14N216O assigned by CRDS in the 6950–7653 cm−1 region are provided as supplementary material. -- Highlights: ► Line intensities of 13 bands of 14N216O in the 6950–7653 cm−1 region are measured. ► Effective dipole moment parameters for ΔP=12, 13, 14 series of bands are refined. ► List of the 14N216O transitions observed in the 6950–7653 cm−1 region is provided

  16. Linear cavity optical-feedback cavity-enhanced absorption spectroscopy with a quantum cascade laser.

    Science.gov (United States)

    Bergin, A G V; Hancock, G; Ritchie, G A D; Weidmann, D

    2013-07-15

    A cw distributed feedback quantum cascade laser (DFB-QCL) coupled to a two-mirror linear optical cavity has been used to successfully demonstrate optical-feedback cavity-enhanced absorption spectroscopy (OF-CEAS) at 5.5 μm. The noise-equivalent absorption coefficient, α(min), was 2.4×10(-8) cm(-1) for 1 s averaging, limited by etalon-fringing. The temporal stability of the instrument allows NO detection down to 5 ppb in 2 s. PMID:23939085

  17. High resolution and high precision absorption spectroscopy using high finesse cavities: application to the study of molecules with atmospheric interest; Cavites de haute finesse pour la spectroscopie d'absorption haute sensibilite et haute precision: application a l'etude de molecules d'interet atmospherique

    Energy Technology Data Exchange (ETDEWEB)

    Motto-Ros, V.

    2005-12-15

    High finesse cavities are used to measure very weak absorption features. Two different methodologies are investigated and applied to the study of molecules with atmospheric interest. First, Continuous Wave - Cavity Ring Down Spectroscopy (CW-CRDS) is used to study the atmospheric spectra of water vapour in the near infrared range. These measurements are performed for temperature and pressure of atmospheric relevance for DIAL applications (Differential Absorption Lidar). This study, financed by the European Space Agency (ESA), goes with the WALES mission (Water Vapour Lidar Experiment in Space). The experimental setup was conceived in order to control pressure, temperature and relative humidity conditions. A particular attention is done to characterize and describe the spectrometer. Then, measurements of red Oxygen B band are performed to demonstrate the huge performance of Optical Feedback Cavity Enhanced Absorption Spectroscopy (OF-CEAS). The desired optical feedback is obtained by light injection into the high finesse cavity through a glass plate placed inside the cavity and closed to the Brewster angle. We show a measurement dynamical range of 5 orders of magnitude (10{sup -5} to 10{sup -10} /cm) and a sensitivity of 10{sup -10} /cm/{radical} Hz. Also, sampling absorption spectra by the super linear cavity frequency comb allows very precise frequency measurements. This is demonstrated by the determination of Oxygen pressure shifts with an absolute accuracy of around 5 x 10{sup -5} cm{sup -1}/atm. To our knowledge, we provide the highest accuracy ever reported for this parameter. (author)

  18. Cavity-enhanced ultrafast two-dimensional spectroscopy using higher-order modes

    CERN Document Server

    Allison, Thomas K

    2016-01-01

    We describe methods using frequency combs and optical resonators for recording two-dimensional (2D) ultrafast spectroscopy signals with high sensitivity. By coupling multiple frequency combs to higher-order modes of one or more optical cavities, background-free, cavity-enhanced 2D spectroscopy signals are naturally generated via phase cycling. As in cavity-enhanced ultrafast transient absorption spectroscopy (CE-TAS), the signal to noise is enhanced by a factor proportional to the cavity finesse squared, so even using cavities of modest finesse, a very high sensitivity is expected, enabling ultrafast 2D spectroscopy experiments in dilute molecular beams.

  19. Coherent cavity-enhanced dual-comb spectroscopy

    CERN Document Server

    Fleisher, Adam J; Reed, Zachary D; Hodges, Joseph T; Plusquellic, David F

    2016-01-01

    Dual-comb spectroscopy allows for the rapid, multiplexed acquisition of high-resolution spectra without the need for moving parts or low-resolution dispersive optics. This method of broadband spectroscopy is most often accomplished via tight phase locking of two mode-locked lasers, or via sophisticated signal processing algorithms, and therefore long integration times are difficult to achieve. Here we demonstrate an alternative approach to dual-comb spectroscopy using two phase modulator combs originating from a single continuous-wave laser capable of > 2 hours of coherent real-time averaging. The combs of > 250 teeth and 203 MHz spacing were generated by driving the phase modulators with step-recovery diodes, passive devices that provided low-phase-noise harmonics for efficient coupling into an enhancement cavity at picowatt optical powers. With this approach, we demonstrate the sensitivity to simultaneously monitor ambient levels of CO$_2$, CO, HDO, and H$_2$O at a maximum acquisition rate of 150 kHz. Robus...

  20. Cavity ringdown spectroscopy with widely tunable swept-frequency lasers

    International Nuclear Information System (INIS)

    Full text: A novel approach to cavity ringdown (CRD) spectroscopy based on swept-frequency (SF) lasers enables rapid measurement of CRD absorption spectra. Our new SF CRD spectrometer incorporates a miniature widely-tunable continuous-wave SF laser and requires less than 1 s to record wide-ranging absorption spectra with high sensitivity in a single rapid sweep of the laser frequency. The spectrometer has a single-ended transmitter-receiver configuration based on retro-reflected optical-heterodyne detection, and yields a simple, compact, versatile instrument for efficient sensing of gases. The performance of the spectrometer is demonstrated by measuring weak absorption spectra of carbon dioxide gas at 1.5-1.6 μm. Copyright (2005) Australian Institute of Physics

  1. Feasibility Study of Using Short Wave Infrared Cavity Ringdown Spectroscopy (SWIR-CRDS) for Biological Agent Detection

    Energy Technology Data Exchange (ETDEWEB)

    Aker, Pam M.; Johnson, Timothy J.; Williams, Richard M.; Valentine, Nancy B.

    2007-10-01

    This project focused on determining the feasibility of using short wave infrared (SWIR) cavity ring down spectroscopy (CRDS) as a means for real-time detection of biological aerosols. The first part of the project involved identifying biological agent signatures that could be detected with SWIR CRDS. After an exhaustive search of the open literature it was determined that whole biological spores and/or cells would not be good candidates for direct SWIR CRDS probing because they have no unique SWIR signatures. It was postulated that while whole cells or spores are not good candidates for SWIR CRDS detection, their pyrolysis break-down products might be. A literature search was then conducted to find biological pyrolysis products with low molecular weights and high symmetry since these species most likely would have overtone and combination vibrational bands that can be detected in the SWIR. It was determined that pyrrole, pyridine and picolinamide were good candidates for evaluation. These molecules are formed when proteins and porphyrins, proteins and dipicolinic acid, and dipicolinic acid are pyrolyzed, respectively. The second part of the project involved measuring quantitative SWIR spectra of pyrrole, pyridine and picolinamide in PNNL’s FTIR Spectroscopy Laboratory. Spectral information about these molecules, in the vapor phase is sparse – there were only a few prior studies that measured line positions and no information on absorption cross sections. Absorption cross sections are needed in order to estimate the SWIR CRDS detection sensitivity, and line position determines what type of laser will be needed for the sensor. The results of the spectroscopy studies allowed us to estimate the SWIR CRDS detection sensitivity for pyrrole to be 3 x 1012 molec cm-3 or 0.1 ppmv, and for pyridine it was 1.5 x 1015 molec cm-3 or 0.6 ppmv. These detection sensitivity limits are close what we have measured for ammonia. Given these detection limits we then estimated the

  2. The Development of Cavity Ringdown Spectroscopy as a Toxic Metal Continuous Emission Monitor

    International Nuclear Information System (INIS)

    Innovative program to explore the viability of using Cavity Ringdown Spectroscopy (CRDS) for trace analysis and monitoring of remediation processes for hazardous and radioactive wastes. Cavity ringdown spectroscopy is a measurement of the rate of absorption of a sample within a closed optical cavity rather than the standard measurement of the absorbed signal strength over a given sample path. It is a technique capable of providing ultra-sensitive absorption measurements in hostile environments using commercially available easy-to-use pulsed lasers. The inherent high sensitivity stems from both the long effective sample pathlengths possible and the relaxed constraints on the accuracy of the measurement of the cavity decay time

  3. Cavity-Enhanced Absorption Spectroscopy and Photoacoustic Spectroscopy for Human Breath Analysis

    Science.gov (United States)

    Wojtas, J.; Tittel, F. K.; Stacewicz, T.; Bielecki, Z.; Lewicki, R.; Mikolajczyk, J.; Nowakowski, M.; Szabra, D.; Stefanski, P.; Tarka, J.

    2014-12-01

    This paper describes two different optoelectronic detection techniques: cavity-enhanced absorption spectroscopy and photoacoustic spectroscopy. These techniques are designed to perform a sensitive analysis of trace gas species in exhaled human breath for medical applications. With such systems, the detection of pathogenic changes at the molecular level can be achieved. The presence of certain gases (biomarkers), at increased concentration levels, indicates numerous human diseases. Diagnosis of a disease in its early stage would significantly increase chances for effective therapy. Non-invasive, real-time measurements, and high sensitivity and selectivity, capable of minimum discomfort for patients, are the main advantages of human breath analysis. At present, monitoring of volatile biomarkers in breath is commonly useful for diagnostic screening, treatment for specific conditions, therapy monitoring, control of exogenous gases (such as bacterial and poisonous emissions), as well as for analysis of metabolic gases.

  4. Spatial Resolution of Combined Wavelength Modulation Spectroscopy with Integrated Cavity Output Spectroscopy for Atomic Oxygen Detection

    Science.gov (United States)

    Matsui, Makoto; Nakajima, Daisuke

    2015-09-01

    For developments of thermal protection system, atomic oxygen plays important role. However, its measurement method has not been established because the pressure in front of TPS test materials is as high as a few kPa. Our group proposed combined wavelength modulation and integrated output spectroscopies based on the forbidden transition at OI 636 nm to measure the ground-state number densities. In this study, WM-ICOS system is developed and applied to a microwave oxygen plasma to evaluate measurable region. As a result, the estimated number density by ICOS could be measured as low as 1021 m21. For the condition, WM-ICOS was applied. The signal to noise ratio of the 2f signal was 40.4. Then, the sensitivity was improved about 26. This result corresponding to the measurement limit of the partial atomic oxygen pressure of 250 Pa. The sensitivity of WM-ICOS was found to enough to diagnose the shock layer in high enthalpy flows. However, the spatial resolution was as large as 8 mm. The size of the beam pattern depends on the cavity length, robust ness of the cavity and accuracy of the cavity alignment. In this presentation, the relationship among these parameters will be discussed.

  5. Optical-Feedback Cavity-Enhanced Absorption Spectroscopy with a Quantum Cascade Laser.

    OpenAIRE

    Maisons, G.; Gorrotxategi Carbajo, P.; Carras, M.; Romanini, D.

    2010-01-01

    Optical{feedback cavity{enhanced absorption spectroscopy is demonstrated in the mid{IR using a quantum cascade laser (emitting at 4.46 ¹m). The laser linewidth reduction and frequency locking by selective optical feedback from the resonant cavity ¯eld turns out to be particularly important in this spectral range: It allows strong cavity transmission which compensates for low light sensitivity, especially when using room temperature detectors. We obtain a noise equivalent absorption coe±cient ...

  6. Molecular Laser Spectroscopy as a Tool for Gas Analysis Applications

    Directory of Open Access Journals (Sweden)

    Javis Anyangwe Nwaboh

    2011-01-01

    Full Text Available We have used the traceable infrared laser spectrometric amount fraction measurement (TILSAM method to perform absolute concentration measurements of molecular species using three laser spectroscopic techniques. We report results performed by tunable diode laser absorption spectroscopy (TDLAS, quantum cascade laser absorption spectroscopy (QCLAS, and cavity ring down spectroscopy (CRDS, all based on the TILSAM methodology. The measured results of the different spectroscopic techniques are in agreement with respective gravimetric values, showing that the TILSAM method is feasible with all different techniques. We emphasize the data quality objectives given by traceability issues and uncertainty analyses.

  7. Molecular Laser Spectroscopy as a Tool for Gas Analysis Applications

    International Nuclear Information System (INIS)

    We have used the traceable infrared laser spectrometric amount fraction measurement (TILSAM) method to perform absolute concentration measurements of molecular species using three laser spectroscopic techniques. We report results performed by tunable diode laser absorption spectroscopy (TDLAS), quantum cascade laser absorption spectroscopy (QCLAS), and cavity ring down spectroscopy (CRDS), all based on the TILSAM methodology. The measured results of the different spectroscopic techniques are in agreement with respective gravimetric values, showing that the TILSAM method is feasible with all different techniques. We emphasize the data quality objectives given by traceability issues and uncertainty analyses.

  8. Continuous Vernier filtering of an optical frequency comb for broadband cavity-enhanced molecular spectroscopy

    CERN Document Server

    Rutkowski, Lucile

    2016-01-01

    We have recently introduced the Vernier-based Direct Frequency Comb Cavity-Enhanced Spectroscopy technique and we present the corresponding formalism for quantitative broadband spectroscopy. We achieve high sensitivity and broadband performance by acquiring spectra covering more than 2000 cm$^{-1}$ around 12600 cm$^{-1}$ (800 nm), resolving the 3$\

  9. Cavity cooling and normal-mode spectroscopy of a bound atom-cavity system

    International Nuclear Information System (INIS)

    Full text: Single atoms strongly coupled to the field of an optical cavity form an attractive system for the realization of an atom-light interface useful for quantum information protocols. An experimental implementation of these schemes requires atoms which are trapped, cooled and localized in the cavity mode at a region of strong coupling. In the experiment presented here, single atoms are trapped and stored in a far-detuned intracavity dipole trap. We demonstrate cavity cooling by illuminating the system with a weak, slightly blue-detuned light beam. This extends the storage time of an atom, which is limited by parametric heating from fluctuations of the intracavity dipole trap, by more than a factor of two. The observed cooling force is of Sisyphus-type and was predicted. A special feature of this force is that it does not rely on the spontaneous emission of a photon by the atom, and therefore the cooling force is at least five times larger than the force achievable for free-space cooling methods with comparable excitation of a two-level atom. Preparing single atoms strongly-coupled to the mode of a high-finesse cavity in this way, we observe two well-resolved normal-mode peaks both in transmission of the cavity as well as in the trap lifetime. The experimental data agree well with a Monte Carlo simulation, demonstrating the localization of the atom to within a tenth of a wavelength at a cavity antinode. The ability to individually excite the normal modes of a bound atom-cavity system shows that we have reached good control over this fundamental quantum system. (author)

  10. Photoreflectance spectroscopy study of vertical cavity surface emitting laser structures

    International Nuclear Information System (INIS)

    This paper summarises the application of the laser-based electro-absorptive technique of photoreflectance (PR) for the study of vertical cavity surface emitting lasers (VCSELs). PR results are shown to reveal the technologically important cavity mode and ground state quantum well exciton structures. AlGaAs/GaAs based quantum well VCSELs were examined with and without top mirror layers as a function of laser pump excitation conditions, with results compared with angle-dependent PR data. Cavity mode and quantum well alignments were also studied with reference to the un-modulated reflectance signal as well as correlated with photoluminescence data. The results demonstrate the importance of PR metrology for state-of-art VCSEL characterisation

  11. Effects of incomplete light extinction in frequency-agile, rapid scanning spectroscopy

    Science.gov (United States)

    Long, D. A.; Wójtewicz, S.; Hodges, J. T.

    2013-05-01

    The effect of finite beam extinction ratio on the precision and accuracy of cavity ring-down decay time constant measurements was examined using the frequency-agile, rapid scanning, cavity ring-down spectroscopy (FARS-CRDS) technique. This new approach to CRDS uses a waveguide-based electro-optic phase modulator (EOM) to provide a laser beam extinction ratio as high as 80 dB: a value that is ≍30 dB greater than that typically achieved with acousto-optic-modulator- based beam switches. We find that the observed measurement precision scales inversely with extinction ratio, such that an EOM enables measurement of the cavity ring-down decay time with a relative precision of ≍8×10-5. We demonstrate that insufficient extinction can be the dominant cause of statistical uncertainty for extinction ratios below 60 dB. Furthermore, insufficient extinction can result in non-exponential decays, which cause systematic measurement biases in cavity losses and absorption.

  12. Plasma-cavity ringdown spectroscopy for analytical measurement: Progress and prospectives

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Sida; Liu, Wei [Research Center of Analytical Instrumentation, Analytical and Testing Center, College of Chemistry, Sichuan University, Chengdu (China); Zhang, Xiaohe [College of Water Resources and Hydropower, Sichuan University, Chengdu (China); Duan, Yixiang, E-mail: yduan@scu.edu.cn [Research Center of Analytical Instrumentation, Analytical and Testing Center, College of Chemistry, Sichuan University, Chengdu (China)

    2013-07-01

    Plasma-cavity ringdown spectroscopy is a powerful absorption technique for analytical measurement. It combines the inherent advantages of high sensitivity, absolute measurement, and relative insensitivity to light source intensity fluctuations of the cavity ringdown technique with use of plasma as an atomization/ionization source. In this review, we briefly describe the background and principles of plasma-cavity ringdown spectroscopy(CRDS) technology, the instrumental components, and various applications. The significant developments of the plasma sources, lasers, and cavity optics are illustrated. Analytical applications of plasma-CRDS for elemental detection and isotopic measurement in atomic spectrometry are outlined in this review. Plasma-CRDS is shown to have a promising future for various analytical applications, while some further efforts are still needed in fields such as cavity design, plasma source design, instrumental improvement and integration, as well as potential applications in radical and molecular measurements. - Highlights: • Plasma-based cavity ringdown spectroscopy • High sensitivity and high resolution • Elemental and isotopic measurements.

  13. Cavity-Enhanced Frequency-Agile Rapid Scanning (fars) Spectroscopy: Experimental Realizations and Measurement Results

    Science.gov (United States)

    Long, David A.; Truong, Gar-Wing; Zee, Roger Van; Plusquellic, David F.; Hodges, Joseph T.

    2013-06-01

    We present a series of experimental realizations of cavity-enhanced, frequency-agile rapid scanning (FARS) spectroscopy using distributed feedback diode lasers, external cavity diode lasers, and ultra-narrow linewidth fiber lasers. FARS offers a scanning rate which is limited only by the cavity response time itself as well as a microwave-level frequency axis. Finally, it allows for an absorption sensitivity which is one of the highest ever reported. These realizations offer a range of applications from low-cost field measurements of trace gases to laboratory-based metrology.

  14. Cavity-Enhanced Raman Spectroscopy of Natural Gas with Optical Feedback cw-Diode Lasers

    OpenAIRE

    Hippler, M

    2015-01-01

    We report on improvements made on our previously introduced technique of cavity-enhanced Raman spectroscopy (CERS) with optical feedback cw-diode lasers in the gas phase, including a new mode-matching procedure which keeps the laser in resonance with the optical cavity without inducing long-term frequency shifts of the laser, and using a new CCD camera with improved noise performance. With 10 mW of 636.2 nm diode laser excitation and 30 s integration time, cavity enhancement achieves noise-eq...

  15. Non-linear Spectroscopy of Sr Atoms in an Optical Cavity for Laser Stabilization

    CERN Document Server

    Christensen, Bjarke T R; Schäffer, Stefan A; Westergaard, Philip G; Ye, Jun; Holland, Murray; Thomsen, Jan W

    2015-01-01

    We study the non-linear interaction of a cold sample of strontium-88 atoms coupled to a single mode of a low finesse optical cavity in the so-called bad cavity limit and investigate the implications for applications to laser stabilization. The atoms are probed on the weak inter-combination line $\\lvert 5s^{2} \\, ^1 \\textrm{S}_0 \\rangle \\,-\\, \\lvert 5s5p \\, ^3 \\textrm{P}_1 \\rangle$ at 689 nm in a strongly saturated regime. Our measured observables include the atomic induced phase shift and absorption of the light field transmitted through the cavity represented by the complex cavity transmission coefficient. We demonstrate high signal-to-noise-ratio measurements of both quadratures - the cavity transmitted phase and absorption - by employing FM spectroscopy (NICE-OHMS). We also show that when FM spectroscopy is employed in connection with a cavity locked to the probe light, observables are substantially modified compared to the free space situation where no cavity is present. Furthermore, the non-linear dynami...

  16. Linewidth measurement of external grating cavity quantum cascade laser using saturation spectroscopy

    Science.gov (United States)

    Mukherjee, Nandini; Go, Rowel; Patel, C. Kumar N.

    2008-03-01

    A room temperature external grating cavity (EGC) quantum cascade laser (QCL) is characterized using saturation spectroscopy of NO2. The presence of two strong EGC QCL waveguide modes is evident from the saturation spectra. A linewidth of 21MHz for each EGC-QCL mode is measured from the width of the saturation peak at 10mTorr pressure of NO2.

  17. Cavities

    Science.gov (United States)

    ... the bacteria produce acids that cause decay. Tooth pain occurs after decay reaches the inside of the tooth. Dentists can detect cavities by examining the teeth and taking x-rays periodically. Good oral hygiene and regular dental care plus a healthy diet can help prevent cavities. ...

  18. a New Broadband Cavity Enhanced Frequency Comb Spectroscopy Technique Using GHz Vernier Filtering.

    Science.gov (United States)

    Morville, Jérôme; Rutkowski, Lucile; Dobrev, Georgi; Crozet, Patrick

    2015-06-01

    We present a new approach to Cavity Enhanced - Direct Frequency Comb Spectroscopy where the full emission bandwidth of a Titanium:Sapphire laser is exploited at GHz resolution. The technique is based on a low-resolution Vernier filtering obtained with an appreciable -actively stabilized- mismatch between the cavity Free Spectral Range and the laser repetition rate, using a diffraction grating and a split-photodiode. This particular approach provides an immunity to frequency-amplitude noise conversion, reaching an absorption baseline noise in the 10-9 cm-1 range with a cavity finesse of only 3000. Spectra covering 1800 cm-1 (˜ 55 THz) are acquired in recording times of about 1 second, providing an absorption figure of merit of a few 10-11 cm-1/√{Hz}. Initially tested with ambient air, we report progress in using the Vernier frequency comb method with a discharge source of small radicals. Rutkowski et al, Opt. Lett., 39(23)2014

  19. Broadband cavity enhanced spectroscopy in the ultraviolet spectral region for measurements of nitrogen dioxide and formaldehyde

    Science.gov (United States)

    Washenfelder, R. A.; Attwood, A. R.; Flores, J. M.; Rudich, Y.; Brown, S. S.

    2015-09-01

    Formaldehyde (CH2O) is the most abundant aldehyde in the atmosphere, and strongly affects photochemistry through its photolysis. We describe simultaneous measurements of CH2O and nitrogen dioxide (NO2) using broadband cavity enhanced spectroscopy in the ultraviolet spectral region. The light source consists of a continuous-wave diode laser focused into a Xenon bulb to produce a plasma that emits high-intensity, broadband light. The plasma discharge is optically filtered and coupled into a 1 m optical cavity. The reflectivity of the cavity mirrors is 0.99933 ± 0.00003 (670 ppm loss) at 338 nm, as determined from the known Rayleigh scattering of He and zero air. This mirror reflectivity corresponds to an effective path length of 1.49 km within the 1 m cell. We measure the cavity output over the 315-350 nm spectral region using a grating monochromator and charge-coupled device (CCD) array detector. We use published reference spectra with spectral fitting software to simultaneously retrieve CH2O and NO2 concentrations. Independent measurements of NO2 standard additions by broadband cavity enhanced spectroscopy and cavity ringdown spectroscopy agree within 2 % (slope for linear fit = 0.98 ± 0.03 with r2 = 0.998). Standard additions of CH2O measured by broadband cavity enhanced spectroscopy and calculated based on flow dilution are also well-correlated, with r2 = 0.9998. During constant, mixed additions of NO2 and CH2O, the 30 s measurement precisions (1σ) of the current configuration were 140 and 210 pptv, respectively. The current 1-min detection limit for extinction measurements at 315-350 nm provides sufficient sensitivity for measurement of trace gases in laboratory experiments and ground-based field experiments. Additionally, the instrument provides highly accurate, spectroscopically-based trace gas detection that may complement higher precision techniques based on non-absolute detection methods. In addition to trace gases, this approach will be appropriate for

  20. Broadband cavity enhanced spectroscopy in the ultraviolet spectral region for measurements of nitrogen dioxide and formaldehyde

    OpenAIRE

    Washenfelder, R. A.; A. R. Attwood; Flores, J. M.; Rudich, Y.; S. S. Brown

    2015-01-01

    Formaldehyde (CH2O) is the most abundant aldehyde in the atmosphere, and strongly affects photochemistry through its photolysis. We describe simultaneous measurements of CH2O and nitrogen dioxide (NO2) using broadband cavity enhanced spectroscopy in the ultraviolet spectral region. The light source consists of a continuous-wave diode laser focused into a Xenon bulb to produce a plasma that emits high-intensity, broadband light. The plasma discharge is optically filtered and ...

  1. Broadband Cavity Enhanced Differential Optical Absorption Spectroscopy (CE-DOAS) – applicability and corrections

    OpenAIRE

    U. Platt; J. Meinen; D. Pöhler; T. Leisner

    2008-01-01

    Atmospheric trace gas measurements by cavity assisted long-path absorption spectroscopy are an emerging technology. An interesting approach is the combination of CEAS with broadband light sources, the broadband CEAS (BB-CEAS). BB-CEAS lends itself to the application of the DOAS technique to analyse the derived absorption spectra. While the DOAS approach has enormous advantages in terms of sensitivity and specificity of the measurement, an important implication is the reduction of the light pa...

  2. Analysis of Trace Impurities in Semiconductor Gas via Cavity-Enhanced Direct Frequency Comb Spectroscopy

    OpenAIRE

    Cossel, Kevin C.; Adler, Florian; Bertness, Kris A.; Thorpe, Michael J.; Feng, Jun; Raynor, Mark W.; Ye, Jun

    2010-01-01

    Cavity-enhanced direct frequency comb spectroscopy (CE-DFCS) has demonstrated powerful potential for trace gas detection based on its unique combination of high bandwidth, rapid data acquisition, high sensitivity, and high resolution, which is unavailable with conventional systems. However, previous demonstrations have been limited to proof-of-principle experiments or studies of fundamental laboratory science. Here we present the development of CE-DFCS towards an industrial application -- mea...

  3. Broadband Cavity Enhanced Differential Optical Absorption Spectroscopy (CE-DOAS – applicability and corrections

    Directory of Open Access Journals (Sweden)

    D. Pöhler

    2009-11-01

    Full Text Available Atmospheric trace gas measurements by cavity assisted long-path absorption spectroscopy are an emerging technology. An interesting approach is the combination of CEAS with broadband light sources, the broadband CEAS (BB-CEAS. BB-CEAS lends itself to the application of the DOAS technique to analyse the derived absorption spectra. While the DOAS approach has enormous advantages in terms of sensitivity and specificity of the measurement, an important implication is the reduction of the light path by the trace gas absorption, since cavity losses due to absorption by gases reduce the quality (Q of the cavity. In fact, at wavelength, where the quality of the BB-CEAS cavity is dominated by the trace gas absorption (especially at very high mirror reflectivity, the average light path will vary nearly inversely with the trace gas concentration and the strength of the band will become only weakly dependent on the trace gas concentration c in the cavity, (the differential optical density being proportional to the logarithm of the trace gas concentration. Only in the limiting case where the mirror reflectivity determines Q at all wavelength, the strength of the band as seen by the CE-DOAS instrument becomes directly proportional to the concentration c. We investigate these relationships in detail and present methods to correct for the cases between the two above extremes, which are of course the important ones in practice.

  4. Broadband Cavity Enhanced Differential Optical Absorption Spectroscopy (CE-DOAS – applicability and corrections

    Directory of Open Access Journals (Sweden)

    D. Pöhler

    2008-12-01

    Full Text Available Atmospheric trace gas measurements by cavity assisted long-path absorption spectroscopy are an emerging technology. An interesting approach is the combination of CEAS with broad band light sources, the broad-band CEAS (BB-CEAS. BB-CEAS lends itself to the application of the DOAS technique to analyse the derived absorption spectra. While the DOAS approach has enormous advantages in terms of sensitivity and specificity of the measurement, an important implication is the reduction of the light path by the trace gas absorption, since cavity losses due to absorption by gases reduce the quality (Q of the cavity. In fact, at wavelength, where the quality of the BB-CEAS cavity is dominated by the trace gas absorption (esp. at very high mirror reflectivity, the light path will vary inversely with the trace gas concentration and the strength of the band will become nearly independent of the trace gas concentration c in the cavity, rendering the CEAS Method useless for trace gas measurements. Only in the limiting case where the mirror reflectivity determines Q at all wavelength, the strength of the band as seen by the BB-CEAS instrument becomes proportional to the concentration c. We investigate these relationships in detail and present methods to correct for the cases between the two above extremes, which are of course the important ones in practice.

  5. Saturation dynamics and working limits of saturated absorption cavity ringdown spectroscopy.

    Science.gov (United States)

    Sadiek, Ibrahim; Friedrichs, Gernot

    2016-08-17

    Cavity ringdown spectroscopy (CRDS) in the linear absorption regime is a well-established method for sensitive trace gas detection, but only a few studies have addressed quantitative measurements in the presence of a saturated sample. In fact, saturation is usually avoided in order to escape from the required complex modeling of the saturation process that depends on the characteristics of the absorbing species, its interaction with the surrounding gas as well as on the temporal and spectral characteristics of the cavity excitation. Conversely, the novel saturated-absorption cavity ringdown spectroscopy approach (SCAR/Sat-CRDS) takes advantage of sample saturation in order to allow one to extract both the gas absorption and the empty cavity loss rates from a single ringdown event. Using a new continuous-wave infrared CRD spectrometer equipped with a tunable narrow-bandwidth high-power OPO laser system and a 18 bit digitizer, the transient dynamics of absorption saturation and the working limits of the Sat-CRDS approach in terms of its ability to extract reliable trace gas concentrations have been experimentally studied in this work. Using a strong methane transition as a test case, the excitation power P0 and saturation power PS have been systematically varied to explore a wide range of saturation regimes. At pressures 5 μbar γc, a pronounced coupling between the two parameters has been observed. Finally, a standard error analysis was performed revealing that the Sat-CRDS approach holds its advantages over conventional CRDS implementations in particular when the attainable ultimate detection sensitivity is limited by uncertainties in the empty cavity ringdown constant. PMID:27488884

  6. Sensitive and ultra-fast species detection using pulsed cavity ringdown spectroscopy

    KAUST Repository

    Alquaity, Awad

    2015-01-01

    Pulsed cavity ringdown spectroscopy (CRDS) is used to develop a novel, ultra-fast, high-sensitivity diagnostic for measuring species concentrations in shock tube experiments. The diagnostic is demonstrated by monitoring trace concentrations of ethylene in the mid-IR region near 949.47 cm-1. Each ringdown measurement is completed in less than 1 μs and the time period between successive pulses is 10 μs. The high sensitivity diagnostic has a noise-equivalent detection limit of 1.08 x 10-5 cm-1 which enables detection of 15 ppm ethylene at fuel pyrolysis conditions (1845 K and 2 bar) and 294 ppb ethylene under ambient conditions (297 K and 1 bar). To our knowledge, this is the first successful application of the cavity ringdown method to the measurement of species time-histories in a shock tube. © 2015 OSA.

  7. Sensitive CH4 detection applying quantum cascade laser based optical feedback cavity-enhanced absorption spectroscopy.

    Science.gov (United States)

    Lang, N; Macherius, U; Wiese, M; Zimmermann, H; Röpcke, J; van Helden, J H

    2016-03-21

    We report on sensitive detection of atmospheric methane employing quantum cascade laser based optical feedback cavity-enhanced absorption spectroscopy (OF-CEAS). An instrument has been built utilizing a continuous-wave distributed feedback quantum cascade laser (cw-QCL) with a V-shaped cavity, a common arrangement that reduces feedback to the laser from non-resonant reflections. The spectrometer has a noise equivalent absorption coefficient of 3.6 × 10-9 cm-1 Hz-1/2 for a spectral scan of CH4 at 7.39 μm. From an Allan-Werle analysis a detection limit of 39 parts per trillion of CH4 at atmospheric pressure within 50 s acquisition time was found. PMID:27136874

  8. New Developments of Broadband Cavity Enhanced Spectroscopic Techniques

    Science.gov (United States)

    Walsh, A.; Zhao, D.; Linnartz, H.; Ubachs, W.

    2013-06-01

    In recent years, cavity enhanced spectroscopic techniques, such as cavity ring-down spectroscopy (CRDS), cavity enhanced absorption spectroscopy (CEAS), and broadband cavity enhanced absorption spectroscopy (BBCEAS), have been widely employed as ultra-sensitive methods for the measurement of weak absorptions and in the real-time detection of trace species. In this contribution, we introduce two new cavity enhanced spectroscopic concepts: a) Optomechanical shutter modulated BBCEAS, a variant of BBCEAS capable of measuring optical absorption in pulsed systems with typically low duty cycles. In conventional BBCEAS applications, the latter substantially reduces the signal-to-noise ratio (S/N), consequently also reducing the detection sensitivity. To overcome this, we incorporate a fast optomechanical shutter as a time gate, modulating the detection scheme of BBCEAS and increasing the effective duty cycle reaches a value close to unity. This extends the applications of BBCEAS into pulsed samples and also in time-resolved studies. b) Cavity enhanced self-absorption spectroscopy (CESAS), a new spectroscopic concept capable of studying light emitting matter (plasma, flames, combustion samples) simultaneously in absorption and emission. In CESAS, a sample (plasma, flame or combustion source) is located in an optically stable cavity consisting of two high reflectivity mirrors, and here it acts both as light source and absorbing medium. A high detection sensitivity of weak absorption is reached without the need of an external light source, such as a laser or broadband lamp. The performance is illustrated by the first CESAS result on a supersonically expanding hydrocarbon plasma. We expect CESAS to become a generally applicable analytical tool for real time and in situ diagnostics. A. Walsh, D. Zhao, W. Ubachs, H. Linnartz, J. Phys. Chem. A, {dx.doi.org/10.1021/jp310392n}, in press, 2013. A. Walsh, D. Zhao, H. Linnartz Rev. Sci. Instrum. {84}(2), 021608 2013. A. Walsh, D. Zhao

  9. Cavity ring-up spectroscopy for ultrafast sensing with optical microresonators

    CERN Document Server

    Rosenblum, Serge; Arazi, Lior; Vollmer, Frank; Dayan, Barak

    2015-01-01

    Spectroscopy of whispering-gallery mode (WGM) microresonators has become a powerful scientific tool, enabling detection of single viruses, nanoparticles, and even single molecules. Yet the demonstrated timescale of these schemes has been limited so far to milliseconds or more. Here we introduce a novel scheme that is orders of magnitude faster, capable of capturing complete spectral snapshots of WGM resonances at nanosecond timescales: cavity ring-up spectroscopy (CRUS). Based on sharply-rising detuned probe pulses, CRUS combines the sensitivity of heterodyne measurements with the highest possible, transform-limited acquisition rate. As a demonstration we capture spectra of microtoroid resonators at time intervals as short as 16 ns, directly monitoring sub-microsecond dynamics of their optomechanical vibrations, thermorefractive response and Kerr nonlinearity. CRUS holds promise for the study of fast biological processes such as enzyme kinetics, protein folding and light harvesting, with applications in other...

  10. Incoherent broadband cavity enhanced absorption spectroscopy using supercontinuum and superluminescent diode sources.

    Science.gov (United States)

    Aalto, Antti; Genty, Goëry; Laurila, Toni; Toivonen, Juha

    2015-09-21

    We investigate incoherent broadband cavity enhanced absorption spectroscopy using a tailored supercontinuum source. By tailoring the supercontinuum spectrum to match the high reflectivity bandwidth of the mirrors, we achieve an unprecedented spectral brightness of more than 7 dBm/nm at wavelengths where the effective absorption path length in the cavity exceeds 40 km. We demonstrate the potential of the source in spectrally broadband measurement of weak overtone transitions of carbon dioxide and methane in the near-infrared 1590 nm - 1700 nm range and evaluate its performance against that of a typical superluminescent diode source. Minimum detectable absorption coefficients (3σ) of 2.2 × 10(-9) cm(-1) and 6.2 × 10(-9) cm(-1) are obtained with the supercontinuum and the superluminescent diode sources, respectively. We further develop a spectral fitting method based on differential optical absorption spectroscopy to fully and properly account for the combined effect of absorption line saturation and limited spectral resolution of the detection. The method allows to cope with high dynamic range of absorption features typical of real-world multi-component measurements. PMID:26406720

  11. Cavity ring-up spectroscopy for dissipative and dispersive sensing in a whispering gallery mode resonator

    CERN Document Server

    Yang, Yong; Kasumie, Sho; Ward, Jonathan M; Chormaic, Síle Nic

    2016-01-01

    In whispering gallery mode resonator sensing applications, the conventional way to detect a change in the parameter to be measured is by observing the steady state transmission spectrum through the coupling waveguide. Alternatively, cavity ring-up spectroscopy (CRUS) sensing can be achieved transiently. In this work, we investigate CRUS using coupled mode equations and find analytical solutions with a large spectral broadening approximation of the input pulse. The relationships between the frequency detuning, coupling gap and ring-up peak height are determined and experimentally verified using an ultrahigh \\textit{Q}-factor silica microsphere. This work shows that distinctive dispersive and dissipative transient sensing can be realised by simply measuring the peak height of the CRUS signal, which might improve the data collection rate.

  12. Time-resolved broadband cavity-enhanced absorption spectroscopy for chemical kinetics.

    Energy Technology Data Exchange (ETDEWEB)

    Sheps, Leonid; Chandler, David W.

    2013-04-01

    Experimental measurements of elementary reaction rate coefficients and product branching ratios are essential to our understanding of many fundamentally important processes in Combustion Chemistry. However, such measurements are often impossible because of a lack of adequate detection techniques. Some of the largest gaps in our knowledge concern some of the most important radical species, because their short lifetimes and low steady-state concentrations make them particularly difficult to detect. To address this challenge, we propose a novel general detection method for gas-phase chemical kinetics: time-resolved broadband cavity-enhanced absorption spectroscopy (TR-BB-CEAS). This all-optical, non-intrusive, multiplexed method enables sensitive direct probing of transient reaction intermediates in a simple, inexpensive, and robust experimental package.

  13. Insights on diagnosis of oral cavity pathologies by infrared spectroscopy: A review

    Science.gov (United States)

    Giorgini, Elisabetta; Balercia, Paolo; Conti, Carla; Ferraris, Paolo; Sabbatini, Simona; Rubini, Corrado; Tosi, Giorgio

    2013-11-01

    Fourier-Transform Infrared microspectroscopy, a largely used spectroscopic technique in basic and industrial researches, offers the possibility to analyze the vibrational features of molecular groups within a variety of environments. In the bioclinical field, and, in particular, in the study of cells, tissues and biofluids, it could be considered a supporting objective technique able to characterize the biochemical processes involved in relevant pathologies, such as tumoral diseases, highlighting specific spectral markers associable with the principal biocomponents (proteins, lipids and carbohydrates). In this article, we review the applications of infrared spectroscopy to the study of tumoral diseases of oral cavity compartments with the aim to improve understanding of biological processes involved during the onset of these lesions and to afford to an early diagnosis. Spectral studies on mouth, salivary glands and oral cystic lesions, objectively discriminate normal from dysplastic and cancer states characterizing also the grading.

  14. Reflection-Absorption Infrared Spectroscopy of Thin Films Using an External Cavity Quantum Cascade Laser

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, Mark C.; Craig, Ian M.; Blake, Thomas A.

    2013-02-04

    We present experimental demonstrations using a broadly tunable external cavity quantum cascade laser (ECQCL) to perform Reflection-Absorption InfraRed Spectroscopy (RAIRS) of thin layers and residues on surfaces. The ECQCL compliance voltage was used to measure fluctuations in the ECQCL output power and improve the performance of the RAIRS measurements. Absorption spectra from self-assembled monolayers of a fluorinated alkane thiol and a thiol carboxylic acid were measured and compared with FTIR measurements. RAIRS spectra of the explosive compounds PETN, RDX, and tetryl deposited on gold substrates were also measured. Rapid measurement times and low noise were demonstrated, with < 1E-3 absorbance noise for a 10 second measurement time.

  15. Microcontroller based resonance tracking unit for time resolved continuous wave cavity-ringdown spectroscopy measurements

    Science.gov (United States)

    Votava, Ondrej; Mašát, Milan; Parker, Alexander E.; Jain, Chaithania; Fittschen, Christa

    2012-04-01

    We present in this work a new tracking servoloop electronics for continuous wave cavity-ringdown absorption spectroscopy (cw-CRDS) and its application to time resolved cw-CRDS measurements by coupling the system with a pulsed laser photolysis set-up. The tracking unit significantly increases the repetition rate of the CRDS events and thus improves effective time resolution (and/or the signal-to-noise ratio) in kinetics studies with cw-CRDS in given data acquisition time. The tracking servoloop uses novel strategy to track the cavity resonances that result in a fast relocking (few ms) after the loss of tracking due to an external disturbance. The microcontroller based design is highly flexible and thus advanced tracking strategies are easy to implement by the firmware modification without the need to modify the hardware. We believe that the performance of many existing cw-CRDS experiments, not only time-resolved, can be improved with such tracking unit without any additional modification to the experiment.

  16. Terahertz quantum-cascade lasers: time domain spectroscopy and micro cavity effects

    International Nuclear Information System (INIS)

    Full text: Quantum Cascade Lasers (QCL) are based on transitions within quantized states of semiconductor nanostructures. This allows the design of the emission wavelength form the infrared to the THz spectral region. We have combined few-cycle THz spectroscopy with quantum cascade technology. This combination allows to perform unique THz time-domain measurements of THz- QCLs. By coupling the few-cycle THz pulse into the waveguide of the QCL, the processes within the active zone can be probed. This gives direct information regarding the energy, dynamics and coherence of transitions in the QCL structure. In addition, we will present micro-cavity quantum-cascade lasers emitting in the THz region. Strong mode confinement in the growth and in-plane directions are provided by a double-plasmon waveguide. We observe whispering-gallery modes and the threshold currents are smaller than from Fabry-Perot cavities; in the detailed study of the emission we were able to observe dynamical frequency pulling effects. (author)

  17. Cavity Enhanced Absorption Spectroscopy with a red LED source for NOx trace analysis

    Science.gov (United States)

    Ventrillard Courtillot, I.; Sciamma O'Brien, E.; Méjean, G.; Romanini, D.

    2009-04-01

    This study presents a high sensitivity absorption system using a red LED source emitting at 625 nm and a small CCD spectrometer as detector [1]. This system is based on IBB-CEAS (Incoherent Broad Band Cavity Enhanced Absorption Spectroscopy). The expected application is the measurement of NO2 and NO3 in urban concentration (ppbv and ppmv levels). The IBB-CEAS was firstly developed with arc lamps and then with LED. Systems based on this technique are easy to use, highly sensitive, compact and robust. They also are inexpensive. Existent techniques to measure NO2 and NO3 are generally slow or not sensitive enough and need frequently calibrations (chemical luminescent) or are characterized by a low spatial resolution (Long Path Differential Optical Absorption Spectroscopy). Previous works based on diodes lasers emitting around 410 nm and coupled with High Finess Cavity proved a highest sensibility than ppbv and a time measurement of 0.1 s [2]. This sensibility is necessary for measurements in unpolluted environment but a more expensive and more complex system is needed. NO2 is chosen for testing as it is stable and available in calibrated diluted samples. An excellent agreement in the range from 610 nm to 630 nm was gotten between an absorption spectrum obtained by IBB-CEAS and a spectrum calculated using a reference NO2 absorption cross section by Voigt et al [3] (after convolution with a 2.05-nm FWHM Gaussian simulating our spectrometer response function). The reflectivity of the mirrors was determined with a commercial spectrophotometer and was used to deduce the absorption spectrum of NO2 from the transmission spectrum of the cavity. We obtained by estimating the sensitivity of our setup from the noise in a baseline measurement of absorption, (standard deviation = 2E-10 cm-1). This corresponds (under atmospheric conditions) to a sensitivity about 0.5 ppbv. NO3 cross-section absorption is 600 times higher than the NO2 (at 623 nm), so a detection limit of 1 pptv is

  18. Aspects of the Application of Cavity Enhanced Spectroscopy to Nitrogen Oxides Detection

    Directory of Open Access Journals (Sweden)

    Zbigniew Bielecki

    2013-06-01

    Full Text Available This article presents design issues of high-sensitive laser absorption spectroscopy systems for nitrogen oxides (NOx detection. Examples of our systems and their investigation results are also described. The constructed systems use one of the most sensitive methods, cavity enhanced absorption spectroscopy (CEAS. They operate at different wavelength ranges using a blue—violet laser diode (410 nm as well as quantum cascade lasers (5.27 µm and 4.53 µm. Each of them is configured as a one or two channel measurement device using, e.g., time division multiplexing and averaging. During the testing procedure, the main performance features such as detection limits and measurements uncertainties have been determined. The obtained results are 1 ppb NO2, 75 ppb NO and 45 ppb N2O. For all systems, the uncertainty of concentration measurements does not exceed a value of 13%. Some experiments with explosives are also discussed. A setup equipped with a concentrator of explosives vapours was used. The detection method is based either on the reaction of the sensors to the nitrogen oxides directly emitted by the explosives or on the reaction to the nitrogen oxides produced during thermal decomposition of explosive vapours. For TNT, PETN, RDX and HMX a detection limit better than 1 ng has been achieved.

  19. Noise-immune cavity-enhanced optical frequency comb spectroscopy: A sensitive technique for high-resolution broadband molecular detection

    CERN Document Server

    Khodabakhsh, Amir; Foltynowicz, Aleksandra

    2014-01-01

    Noise-immune cavity-enhanced optical frequency comb spectroscopy (NICE-OFCS) is a recently developed technique that utilizes phase modulation to obtain immunity to frequency-to-amplitude noise conversion by the cavity modes and yields high absorption sensitivity over a broad spectral range. We describe the principles of the technique and discuss possible comb-cavity matching solutions. We present a theoretical description of NICE-OFCS signals detected with a Fourier transform spectrometer (FTS), and validate the model by comparing it to experimental CO2 spectra around 1575 nm. Our system is based on an Er:fiber femtosecond laser locked to a cavity and phase-modulated at a frequency equal to a multiple of the cavity free spectral range (FSR). The NICE-OFCS signal is detected by a fast-scanning FTS equipped with a high-bandwidth commercial detector. We demonstrate a simple method of passive locking of the modulation frequency to the cavity FSR that significantly improves the long term stability of the system, a...

  20. Photonic crystal cavity modes in the visible range characterized by scattering spectroscopy

    International Nuclear Information System (INIS)

    We fabricate L3 cavities in a silicon nitride photonic crystal, with cavity modes in the visible range. We demonstrate a noninvasive method to characterize the cavities: the sample is illuminated on its edge and the upward-scattering spectrum is measured. We determine the modes' wavelengths, polarizations, and quality factors. We find modes between 700 and 830 nm with quality factors up to 280, polarized along or perpendicular to the cavity. The tuning of the cavity characteristics by means of its geometric parameters (holes sizes and shift) is discussed. The results are analyzed and compared with numerical simulations.

  1. Development of Broad Range Scan Capabilities with Jet Cooled Cavity Ringdown Spectroscopy

    Science.gov (United States)

    Codd, Terrance J.; Chen, Ming-Wei; Miller, Terry A.

    2011-06-01

    We have developed a technique for obtaining broad scans, >100 Cm-1, for jet cooled cavity ringdown spectroscopy (CRDS) spectra. Previously the scans of the jet cooled, CRDS apparatus were limited to <10 Cm-1 due to the use of a narrow linewidth radiation source. However, by coupling our jet cooled, CRDS apparatus with a moderate resolution (≃q 0.05 Cm-1) dye laser we are able to greatly increase our rate of data acquisition thereby gaining the capability to perform broad spectral surveys of jet cooled molecules. As a test of the capabilities of the technique we have scanned the tilde{A}-tilde{X} transition of NO_3 previously reported by Deev et al. at room temperature. We believe that this will be a very useful technique to search for transitions of cold molecules whose frequencies are not well known and which later can be studied using high resolution methods. A. Deev, J. Sommar, and M. Okumura, J. Chem. Phys. 122, 224305 (2005).

  2. Detection of Melanoma Cancer Biomarker Dimethyl Disulfide Using Cavity Ringdown Spectroscopy at 266 nm.

    Science.gov (United States)

    Wang, Zhennan; Sun, Meixiu; Wang, Chuji

    2016-06-01

    Skin cells emit volatile organic compounds (VOCs), and some of them can be used as biomarkers for screening specific diseases. Dimethyl disulfide (DMDS) has been recently reported as a biomarker of melanoma skin cancer (Kwak et al. "Volatile Biomarkers from Human Melanoma Cells". J. Chromatogr. B. 2013. 931: 90-96.). With the motivation of diagnosing melanoma using DMDS as its biomarker, we explore the potential of measuring DMDS using an advanced laser spectroscopic technique as an alternative method. We report on the first DMDS measurements using an experimental system based on cavity ringdown spectroscopy (CRDS). The test samples were mixtures of DMDS vapor and nitrogen in different concentrations. Two sampling methods were investigated to dilute the DMDS sample to low concentrations for ringdown measurements. The results showed that the ringdown system responded to various DMDS concentrations linearly and a theoretical detection limit of sub-ppb (parts per billion) could be achieved at the absorption wavelength of 266 nm. This ringdown system exhibited a high dynamic range for DMDS measurements, from ppm (parts per million) to ppt (parts per trillion) levels, given different laser wavelengths used. The feasibility of developing a portable melanoma screening sensor using the CRDS technique was also demonstrated in this study. PMID:27076515

  3. Spectral contaminant identifier for off-axis integrated cavity output spectroscopy measurements of liquid water isotopes

    International Nuclear Information System (INIS)

    Developments in cavity-enhanced absorption spectrometry have made it possible to measure water isotopes using faster, more cost-effective field-deployable instrumentation. Several groups have attempted to extend this technology to measure water extracted from plants and found that other extracted organics absorb light at frequencies similar to that absorbed by the water isotopomers, leading to δ2H and δ18O measurement errors (Δδ2H and Δδ18O). In this note, the off-axis integrated cavity output spectroscopy (ICOS) spectra of stable isotopes in liquid water is analyzed to determine the presence of interfering absorbers that lead to erroneous isotope measurements. The baseline offset of the spectra is used to calculate a broadband spectral metric, mBB, and the mean subtracted fit residuals in two regions of interest are used to determine a narrowband metric, mNB. These metrics are used to correct for Δδ2H and Δδ18O. The method was tested on 14 instruments and Δδ18O was found to scale linearly with contaminant concentration for both narrowband (e.g., methanol) and broadband (e.g., ethanol) absorbers, while Δδ2H scaled linearly with narrowband and as a polynomial with broadband absorbers. Additionally, the isotope errors scaled logarithmically with mNB. Using the isotope error versus mNB and mBB curves, Δδ2H and Δδ18O resulting from methanol contamination were corrected to a maximum mean absolute error of 0.93 per mille and 0.25 per mille respectively, while Δδ2H and Δδ18O from ethanol contamination were corrected to a maximum mean absolute error of 1.22 per mille and 0.22 per mille . Large variation between instruments indicates that the sensitivities must be calibrated for each individual isotope analyzer. These results suggest that the properly calibrated interference metrics can be used to correct for polluted samples and extend off-axis ICOS measurements of liquid water to include plant waters, soil extracts, wastewater, and alcoholic

  4. Transport Spectroscopy of a Spin-Coherent Dot-Cavity System.

    Science.gov (United States)

    Rössler, C; Oehri, D; Zilberberg, O; Blatter, G; Karalic, M; Pijnenburg, J; Hofmann, A; Ihn, T; Ensslin, K; Reichl, C; Wegscheider, W

    2015-10-16

    Quantum engineering requires controllable artificial systems with quantum coherence exceeding the device size and operation time. This can be achieved with geometrically confined low-dimensional electronic structures embedded within ultraclean materials, with prominent examples being artificial atoms (quantum dots) and quantum corrals (electronic cavities). Combining the two structures, we implement a mesoscopic coupled dot-cavity system in a high-mobility two-dimensional electron gas, and obtain an extended spin-singlet state in the regime of strong dot-cavity coupling. Engineering such extended quantum states presents a viable route for nonlocal spin coupling that is applicable for quantum information processing. PMID:26550890

  5. Two-dimensional Infrared Spectroscopy of vibrational polaritons of molecules in an optical cavity

    CERN Document Server

    Saurabh, Prasoon

    2016-01-01

    Strong coupling of molecular vibrations to an infrared cavity mode affects their nature by creating dressed polariton states. We show how the single and double vibrational polariton manifolds may be controlled by varying the cavity coupling strength, and probed by a time domain 2DIR technique, Double Quantum Coherence (DQC). Applications are made to the amide-I ($CO$) and amide-II ($CN$) bond vibrations of $N-methylacetamide$ (NMA).

  6. Dielectric microwave resonators in TE(011) cavities for electron paramagnetic resonance spectroscopy.

    Science.gov (United States)

    Mett, Richard R; Sidabras, Jason W; Golovina, Iryna S; Hyde, James S

    2008-09-01

    The coupled system of the microwave cylindrical TE(011) cavity and the TE(01delta) dielectric modes has been analyzed in order to determine the maximum achievable resonator efficiency parameter of a dielectric inserted into a cavity, and whether this value can exceed that of a dedicated TE(01delta) mode dielectric resonator. The frequency, Q value, and resonator efficiency parameter Lambda for each mode of the coupled system were calculated as the size of the dielectric was varied. Other output parameters include the relative field magnitudes and phases. Two modes are found: one with fields in the dielectric parallel to the fields in the cavity center and the other with antiparallel fields. Results closely match those from a computer program that solves Maxwell's equations by finite element methods. Depending on the relative natural resonance frequencies of the cavity and dielectric, one mode has a higher Q value and correspondingly lower Lambda than the other. The mode with the higher Q value is preferentially excited by a coupling iris or loop in or near the cavity wall. However, depending on the frequency separation between modes, either can be excited in this way. A relatively narrow optimum is found for the size of the insert that produces maximum signal for both modes simultaneously. It occurs when the self-resonance frequencies of the two resonators are nearly equal. The maximum signal is almost the same as that of the dedicated TE(01delta) mode dielectric resonator alone, Lambda congruent with40 G/W(1/2) at X-band for a KTaO(3) crystal. The cavity is analogous to the second stage of a two-stage coupler. In general, there is no electron paramagnetic resonance (EPR) signal benefit by use of a second stage. However, there is a benefit of convenience. A properly designed sample-mounted resonator inserted into a cavity can give EPR signals as large as what one would expect from the dielectric resonator alone. PMID:19044441

  7. Dielectric microwave resonators in TE011 cavities for electron paramagnetic resonance spectroscopy

    Science.gov (United States)

    Mett, Richard R.; Sidabras, Jason W.; Golovina, Iryna S.; Hyde, James S.

    2008-09-01

    The coupled system of the microwave cylindrical TE011 cavity and the TE01δ dielectric modes has been analyzed in order to determine the maximum achievable resonator efficiency parameter of a dielectric inserted into a cavity, and whether this value can exceed that of a dedicated TE01δ mode dielectric resonator. The frequency, Q value, and resonator efficiency parameter Λ for each mode of the coupled system were calculated as the size of the dielectric was varied. Other output parameters include the relative field magnitudes and phases. Two modes are found: one with fields in the dielectric parallel to the fields in the cavity center and the other with antiparallel fields. Results closely match those from a computer program that solves Maxwell's equations by finite element methods. Depending on the relative natural resonance frequencies of the cavity and dielectric, one mode has a higher Q value and correspondingly lower Λ than the other. The mode with the higher Q value is preferentially excited by a coupling iris or loop in or near the cavity wall. However, depending on the frequency separation between modes, either can be excited in this way. A relatively narrow optimum is found for the size of the insert that produces maximum signal for both modes simultaneously. It occurs when the self-resonance frequencies of the two resonators are nearly equal. The maximum signal is almost the same as that of the dedicated TE01δ mode dielectric resonator alone, Λ ≅40 G/W1/2 at X-band for a KTaO3 crystal. The cavity is analogous to the second stage of a two-stage coupler. In general, there is no electron paramagnetic resonance (EPR) signal benefit by use of a second stage. However, there is a benefit of convenience. A properly designed sample-mounted resonator inserted into a cavity can give EPR signals as large as what one would expect from the dielectric resonator alone.

  8. Ultra-Stable Rubidium-Stabilized External-Cavity Diode Laser Based on the Modulation Transfer Spectroscopy Technique

    Institute of Scientific and Technical Information of China (English)

    QI Xiang-Hui; CHEN Wen-Lan; YI Lin; ZHOU Da-Wei; ZHOU Tong; XIAO Qin; DUAN Jun; ZHOU Xiao-Ji; CHEN Xu-Zong

    2009-01-01

    @@ We construct an ultra-stable external-cavity diode laser via modulation transfer spectroscopy referencing on a hyperfine component of the 87Rb D2 lines at 780 hm. The Doppler-free dispersion-like modulation transfer signal is obtained with high signal-to-noise-ratio. The instability of the laser frequency is measured by beating with an optical frequency comb which is phase-locked to an ultra-stable oven controlled crystal oscillator. The Allan deviation is 3.9×10-13 at 1s averaging time and 9.8×10-14 at 90s averaging time.

  9. Non-linear Spectroscopy of Sr Atoms in an Optical Cavity for Laser Stabilization

    OpenAIRE

    Christensen, Bjarke T. R.; Henriksen, Martin R.; Schäffer, Stefan A.; Westergaard, Philip G.; Ye, Jun; Holland, Murray; Thomsen, Jan W.

    2015-01-01

    We study the non-linear interaction of a cold sample of strontium-88 atoms coupled to a single mode of a low finesse optical cavity in the so-called bad cavity limit and investigate the implications for applications to laser stabilization. The atoms are probed on the weak inter-combination line $\\lvert 5s^{2} \\, ^1 \\textrm{S}_0 \\rangle \\,-\\, \\lvert 5s5p \\, ^3 \\textrm{P}_1 \\rangle$ at 689 nm in a strongly saturated regime. Our measured observables include the atomic induced phase shift and abs...

  10. Optical feedback cavity-enhanced absorption spectroscopy with a 3.24 μm interband cascade laser

    Energy Technology Data Exchange (ETDEWEB)

    Manfred, K. M.; Ritchie, G. A. D. [Department of Chemistry, Physical and Theoretical Chemistry Laboratory, University of Oxford, South Parks Rd, Oxford OX1 3QZ (United Kingdom); Lang, N.; Röpcke, J.; Helden, J. H. van, E-mail: jean-pierre.vanhelden@inp-greifswald.de [Leibniz Institute for Plasma Science and Technology (INP Greifswald), Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany)

    2015-06-01

    The development of interband cascade lasers (ICLs) has made the strong C-H transitions in the 3 μm spectral region increasingly accessible. We present the demonstration of a single mode distributed feedback ICL coupled to a V-shaped optical cavity in an optical feedback cavity-enhanced absorption spectroscopy (OF-CEAS) experiment. We achieved a minimum detectable absorption coefficient, α{sub min}, of (7.1±0.2)×10{sup −8} cm{sup −1} for a spectrum of CH{sub 4} at 3.24 μm with a two second acquisition time (100 scans averaged). This corresponds to a detection limit of 3 ppb CH{sub 4} at atmospheric pressure, which is comparable to previously reported OF-CEAS instruments with diode lasers or quantum cascade lasers. The ability to frequency lock an ICL source in the important 3 μm region to an optical cavity holds great promise for future spectroscopic applications.

  11. A new cryogenic target and microwave cavity for hyperfine structure spectroscopy of antiprotonic helium

    International Nuclear Information System (INIS)

    Full text: A new cryostat with pulse tube refrigeration and gas-tight microwave cavity with a laser and antiproton window has been designed and built to study the hyperfine structure of antiprotonic helium-3. The improvements between this and the old system will be explained. (author)

  12. A narrow-linewidth external cavity quantum dot laser for high-resolution spectroscopy in the near-infrared and yellow spectral ranges

    CERN Document Server

    Nevsky, A Yu; Eisele, Ch; Okhapkin, M; Schiller, S; Gubenko, A; Livshits, D; Mikhrin, S; Krestnikov, I; Kovsh, A

    2008-01-01

    We demonstrate a diode laser system which is suitable for high-resolution spectroscopy in the 1200 nm and yellow spectral ranges. It is based on a two-facet quantum dot chip in a Littrow-type external cavity configuration. The laser is tunable in the range 1125 -1280 nm, with an output power of more than 200 mW and exhibits a free-running linewidth of 200 kHz. Amplitude and frequency noise were characterized, including the dependence of frequency noise on the cavity length. Frequency stabilization to a high-finesse reference cavity is demonstrated reducing the linewidth to about 20 - 30 kHz. Yellow light (> 3 mW) at 578 nm was generated by frequency doubling in an enhancement cavity containing a PPLN crystal. The source has potential application for precision spectroscopy of ultra-cold Yb atoms and molecular hydrogen ions.

  13. Environmental Chamber Study of Atmospheric Chemistry and Secondary Organic Aerosol Formation Using Cavity Enhanced Absorption Spectroscopy

    OpenAIRE

    Liu, Yingdi

    2011-01-01

    Air pollution and global climate change are important environmental issues that affect our society. Deeper understanding of atmospheric chemistry is required to understand these problems and to develop effective control strategies. Environmental chambers have been used for the past few decades to study atmospheric chemistry and investigate processes leading to secondary pollutant formation. This thesis work provides two different high sensitivity real time cavity enhance absorption spectrosco...

  14. Angle-resolved scattering spectroscopy of explosives using an external cavity quantum cascade laser

    Energy Technology Data Exchange (ETDEWEB)

    Suter, Jonathan D.; Bernacki, Bruce E.; Phillips, Mark C.

    2012-04-01

    Investigation of angle-resolved scattering from solid explosives residues on a car door for non-contact sensing geometries. Illumination with a mid-infrared external cavity quantum cascade laser tuning between 7 and 8 microns was detected both with a sensitive single point detector and a hyperspectral imaging camera. Spectral scattering phenomena were discussed and possibilities for hyperspectral imaging at large scattering angles were outlined.

  15. Microwave spectral taxonomy: A semi-automated combination of chirped-pulse and cavity Fourier-transform microwave spectroscopy

    Science.gov (United States)

    Crabtree, Kyle N.; Martin-Drumel, Marie-Aline; Brown, Gordon G.; Gaster, Sydney A.; Hall, Taylor M.; McCarthy, Michael C.

    2016-03-01

    Because of its structural specificity, rotational spectroscopy has great potential as an analytical tool for characterizing the chemical composition of complex gas mixtures. However, disentangling the individual molecular constituents of a rotational spectrum, especially if many of the lines are entirely new or unknown, remains challenging. In this paper, we describe an empirical approach that combines the complementary strengths of two techniques, broadband chirped-pulse Fourier transform microwave spectroscopy and narrowband cavity Fourier transform microwave spectroscopy, to characterize and assign lines. This procedure, called microwave spectral taxonomy, involves acquiring a broadband rotational spectrum of a rich mixture, categorizing individual lines based on their relative intensities under series of assays, and finally, linking rotational transitions of individual chemical compounds within each category using double resonance techniques. The power of this procedure is demonstrated for two test cases: a stable molecule with a rich spectrum, 3,4-difluorobenzaldehyde, and products formed in an electrical discharge through a dilute mixture of C2H2 and CS2, in which spectral taxonomy has enabled the identification of propynethial, HC(S)CCH.

  16. Infrared near-field spectroscopy of trace explosives using an external cavity quantum cascade laser

    Energy Technology Data Exchange (ETDEWEB)

    Craig, Ian M.; Taubman, Matthew S.; Lea, Alan S.; Phillips, Mark C.; Josberger, Erik E.; Raschke, Markus Bernd

    2013-12-16

    Utilizing a broadly-tunable external cavity quantum cascade laser for scattering-type scanning near-field optical microscopy (s-SNOM), we measure infrared spectra of explosives particles by probing characteristic nitro-group resonances in the 7.1-7.9 µm wavelength range. Measurements are presented with spectral resolution of 0.25 cm-1, spatial resolution of 25 nm, <100 attomolar sensitivity, and at a rapid acquisition time of 90 s per spectrum. We demonstrate high reproducibility of the acquired s-SNOM spectra with very high signal-to-noise ratios and relative noise of <0.02 in self-homodyne detection.

  17. On-chip spectroscopy with thermally tuned high-Q photonic crystal cavities

    Energy Technology Data Exchange (ETDEWEB)

    Liapis, Andreas C., E-mail: andreas.liapis@gmail.com; Gao, Boshen; Siddiqui, Mahmudur R. [The Institute of Optics, University of Rochester, Rochester, New York 14627 (United States); Shi, Zhimin [Department of Physics, University of South Florida, Tampa, Florida 33620 (United States); Boyd, Robert W. [The Institute of Optics, University of Rochester, Rochester, New York 14627 (United States); Department of Physics and School of Electrical Engineering and Computer Science, University of Ottawa, Ottawa, Ontario K1N 6N5 (Canada)

    2016-01-11

    Spectroscopic methods are a sensitive way to determine the chemical composition of potentially hazardous materials. Here, we demonstrate that thermally tuned high-Q photonic crystal cavities can be used as a compact high-resolution on-chip spectrometer. We have used such a chip-scale spectrometer to measure the absorption spectra of both acetylene and hydrogen cyanide in the 1550 nm spectral band and show that we can discriminate between the two chemical species even though the two materials have spectral features in the same spectral region. Our results pave the way for the development of chip-size chemical sensors that can detect toxic substances.

  18. On-chip spectroscopy with thermally-tuned high-Q photonic crystal cavities

    CERN Document Server

    Liapis, Andreas C; Siddiqui, Mahmudur R; Shi, Zhimin; Boyd, Robert W

    2015-01-01

    Spectroscopic methods are a sensitive way to determine the chemical composition of potentially hazardous materials. Here, we demonstrate that thermally-tuned high-Q photonic crystal cavities can be used as a compact high-resolution on-chip spectrometer. We have used such a chip-scale spectrometer to measure the absorption spectra of both acetylene and hydrogen cyanide in the 1550 nm spectral band, and show that we can discriminate between the two chemical species even though the two materials have spectral features in the same spectral region. Our results pave the way for the development of chip-size chemical sensors that can detect toxic substances.

  19. Pump-probe differencing technique for cavity-enhanced, noise-canceling saturation laser spectroscopy

    CERN Document Server

    De Vine, G; Close, J D; Gray, M B; Vine, Glenn de; Clelland, David E. Mc; Close, John D.; Gray, Malcolm B.

    2004-01-01

    We present an experimental technique enabling mechanical-noise free, cavity-enhanced frequency measurements of an atomic transition and its hyperfine structure. We employ the 532nm frequency doubled output from a Nd:YAG laser and an iodine vapour cell. The cell is placed in a traveling-wave Fabry-Perot interferometer (FPI) with counter-propagating pump and probe beams. The FPI is locked using the Pound-Drever-Hall (PDH) technique. Mechanical noise is rejected by differencing pump and probe signals. In addition, this differenced error signal gives a sensitive measure of differential non-linearity within the FPI.

  20. On-chip spectroscopy with thermally tuned high-Q photonic crystal cavities

    International Nuclear Information System (INIS)

    Spectroscopic methods are a sensitive way to determine the chemical composition of potentially hazardous materials. Here, we demonstrate that thermally tuned high-Q photonic crystal cavities can be used as a compact high-resolution on-chip spectrometer. We have used such a chip-scale spectrometer to measure the absorption spectra of both acetylene and hydrogen cyanide in the 1550 nm spectral band and show that we can discriminate between the two chemical species even though the two materials have spectral features in the same spectral region. Our results pave the way for the development of chip-size chemical sensors that can detect toxic substances

  1. Fixed-wavelength H2O absorption spectroscopy system enhanced by an on-board external-cavity diode laser

    Science.gov (United States)

    Brittelle, Mack S.; Simms, Jean M.; Sanders, Scott T.; Gord, James R.; Roy, Sukesh

    2016-03-01

    We describe a system designed to perform fixed-wavelength absorption spectroscopy of H2O vapor in practical combustion devices. The system includes seven wavelength-stabilized distributed feedback (WSDFB) lasers, each with a spectral accuracy of  ±1 MHz. An on-board external cavity diode laser (ECDL) that tunes 1320-1365 nm extends the capabilities of the system. Five system operation modes are described. In one mode, a sweep of the ECDL is used to monitor each WSDFB laser wavelength with an accuracy of  ±30 MHz. Demonstrations of fixed-wavelength thermometry at 10 kHz bandwidth in near-room-temperature gases are presented; one test reveals a temperature measurement error of ~0.43%.

  2. Fixed-wavelength H2O absorption spectroscopy system enhanced by an on-board external-cavity diode laser

    International Nuclear Information System (INIS)

    We describe a system designed to perform fixed-wavelength absorption spectroscopy of H2O vapor in practical combustion devices. The system includes seven wavelength-stabilized distributed feedback (WSDFB) lasers, each with a spectral accuracy of  ±1 MHz. An on-board external cavity diode laser (ECDL) that tunes 1320–1365 nm extends the capabilities of the system. Five system operation modes are described. In one mode, a sweep of the ECDL is used to monitor each WSDFB laser wavelength with an accuracy of  ±30 MHz. Demonstrations of fixed-wavelength thermometry at 10 kHz bandwidth in near-room-temperature gases are presented; one test reveals a temperature measurement error of ∼0.43%. (paper)

  3. Microcontroller based resonance tracking unit for time resolved continuous wave cavity-ringdown spectroscopy measurements

    Czech Academy of Sciences Publication Activity Database

    Votava, Ondřej; Mašát, Milan; Parker, A. E.; Jain, Ch.; Fittschen, Ch.

    2012-01-01

    Roč. 83, č. 4 (2012), 043110. ISSN 0034-6748 R&D Projects: GA ČR GA203/09/0422 Institutional support: RVO:61388955 Keywords : CW-DIODE-LASER * DOWN SPECTROSCOPY * KINETICS Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.602, year: 2012

  4. Backaction-limited cavity-sideband spectroscopy of quantum collective motion

    CERN Document Server

    Brahms, Nathan; Schreppler, Sydney; Brooks, Daniel W C; Stamper-Kurn, Dan M

    2011-01-01

    The motion of sub-atomic particles is characteristically quantum mechanical in nature. In contrast, quantum aspects of the motion of massive, many-atom objects are typically obscured by high phonon occupation and thermal noise. This contrast is now diminishing, owing to research efforts to bring the control and measurement of macroscopic motion fully into the quantum regime, using objects with masses from attograms to kilograms. This achievement will be critical for constructing force detectors sensitive to gravitational waves, verifying the correspondence principle at macroscopic scales, and realizing protocols that mechanically store and exchange quantum information. Here, we directly observe the quantization of the collective motion of an ultracold atomic ensemble by measuring the inability of a 0.6 attogram centre-of-mass mode to emit energy from its ground state. Moreover, the optical output of our strongly coupled cavity-optomechanical system contains a spectroscopic record of the energy exchanged betwe...

  5. Design and application of robust rf pulses for toroid cavity NMR spectroscopy

    CERN Document Server

    Skinner, Thomas E; Woelk, Klaus; Gershenzon, Naum I; Glaser, Steffen J

    2010-01-01

    We present robust radio frequency (rf) pulses that tolerate a factor of six inhomogeneity in the B1 field, significantly enhancing the potential of toroid cavity resonators for NMR spectroscopic applications. Both point-to-point (PP) and unitary rotation (UR) pulses were optimized for excitation, inversion, and refocusing using the gradient ascent pulse engineering (GRAPE) algorithm based on optimal control theory. In addition, the optimized parameterization (OP) algorithm applied to the adiabatic BIR-4 UR pulse scheme enabled ultra-short (50 microsec) pulses with acceptable performance compared to standard implementations. OP also discovered a new class of non-adiabatic pulse shapes with improved performance within the BIR-4 framework. However, none of the OP-BIR4 pulses are competitive with the more generally optimized UR pulses. The advantages of the new pulses are demonstrated in simulations and experiments. In particular, the DQF COSY result presented here represents the first implementation of 2D NMR sp...

  6. Infrared near-field spectroscopy of trace explosives using an external cavity quantum cascade laser.

    Science.gov (United States)

    Craig, Ian M; Taubman, Matthew S; Lea, A Scott; Phillips, Mark C; Josberger, Erik E; Raschke, Markus B

    2013-12-16

    Utilizing a broadly-tunable external cavity quantum cascade laser for scattering-type scanning near-field optical microscopy (s-SNOM), we measure infrared spectra of particles of explosives by probing characteristic nitro-group resonances in the 7.1-7.9 µm wavelength range. Measurements are presented with spectral resolution of 0.25 cm(-1), spatial resolution of 25 nm, sensitivity better than 100 attomoles, and at a rapid acquisition time of 90 s per spectrum. We demonstrate high reproducibility of the acquired s-SNOM spectra with very high signal-to-noise ratios and relative noise of <0.02 in self-homodyne detection. PMID:24514618

  7. Real-time, subsecond, multicomponent breath analysis by Optical Parametric Oscillator based Off-Axis Integrated Cavity Output Spectroscopy.

    Science.gov (United States)

    Arslanov, Denis D; Swinkels, Koen; Cristescu, Simona M; Harren, Frans J M

    2011-11-21

    Breath analysis is an attractive field of research, due to its high potential for non-invasive medical diagnostics. Among others, laser-based absorption spectroscopy is an excellent method for the detection of gases in exhaled breath, because it can combine a high sensitivity with a good selectivity, and a high temporal resolution. Here, we use a fast-scanning continuous wave, singly-resonant Optical Parametric Oscillator (wavelength range between 3 and 4 μm, linewidth 40 MHz, output power > 1 W, scanning speed 100 THz/s) with Off-Axis Integrated Cavity Output Spectroscopy for rapid and sensitive trace gas detection. Real-time, low- ppbv detection of ethane is demonstrated in exhaled human breath during free exhalations. Also, simultaneous, real-time multi-component gas detection of ethane, methane and water was performed in exhaled breath using a wide spectral coverage over 17 cm(-1) in 1 second. Furthermore, real-time detection of acetone, a molecule with a wide absorption spectrum, was shown in exhaled breath, with a sub-second time resolution (0.4 s). PMID:22109433

  8. Mid-Infrared Quantum Cascade Laser Based Off-Axis Integrated Cavity Output Spectroscopy for Biogenic Nitric Oxide Detection

    Science.gov (United States)

    Bakhirkin, Yury A.; Kosterev, Anatoliy A.; Roller, Chad; Curl, Robert F.; Tittel, Frank K.

    2004-04-01

    Tunable-laser absorption spectroscopy in the mid-IR spectral region is a sensitive analytical technique for trace-gas quantification. The detection of nitric oxide (NO) in exhaled breath is of particular interest in the diagnosis of lower-airway inflammation associated with a number of lung diseases and illnesses. A gas analyzer based on a continuous-wave mid-IR quantum cascade laser operating at ~5.2 µm and on off-axis integrated cavity output spectroscopy (ICOS) has been developed to measure NO concentrations in human breath. A compact sample cell, 5.3 cm in length and with a volume of less than 80 cm3, that is suitable for on-line and off-line measurements during a single breath cycle, has been designed and tested. A noise-equivalent (signal-to-noise ratio of 1) sensitivity of 10 parts in 10 9 by volume (ppbv) of NO was achieved. The combination of ICOS with wavelength modulation resulted in a 2-ppbv noise-equivalent sensitivity. The total data acquisition and averaging time was 15 s in both cases. The feasibility of detecting NO in expired human breath as a potential noninvasive medical diagnostic tool is discussed.

  9. Ultrasensitive laser spectroscopy for breath analysis

    Science.gov (United States)

    Wojtas, J.; Bielecki, Z.; Stacewicz, T.; Mikołajczyk, J.; Nowakowski, M.

    2012-03-01

    At present there are many reasons for seeking new methods and technologies that aim to develop new and more perfect sensors for different chemical compounds. However, the main reasons are safety ensuring and health care. In the paper, recent advances in the human breath analysis by the use of different techniques are presented. We have selected non-invasive ones ensuring detection of pathogenic changes at a molecular level. The presence of certain molecules in the human breath is used as an indicator of a specific disease. Thus, the analysis of the human breath is very useful for health monitoring. We have shown some examples of diseases' biomarkers and various methods capable of detecting them. Described methods have been divided into non-optical and optical methods. The former ones are the following: gas chromatography, flame ionization detection, mass spectrometry, ion mobility spectrometry, proton transfer reaction mass spectrometry, selected ion flow tube mass spectrometry. In recent twenty years, the optical methods have become more popular, especially the laser techniques. They have a great potential for detection and monitoring of the components in the gas phase. These methods are characterized by high sensitivity and good selectivity. The spectroscopic sensors provide the opportunity to detect specific gases and to measure their concentration either in a sampling place or a remote one. Multipass spectroscopy, cavity ring-down spectroscopy, and photo-acoustic spectroscopy were characterised in the paper as well.

  10. Variable temperature spectroscopy of as-grown and passivated CdS nanowire optical waveguide cavities.

    Science.gov (United States)

    van Vugt, Lambert K; Piccione, Brian; Cho, Chang-Hee; Aspetti, Carlos; Wirshba, Aaron D; Agarwal, Ritesh

    2011-04-28

    Semiconductor nanowire waveguide cavities hold promise for nanophotonic applications such as lasers, waveguides, switches, and sensors due to the tight optical confinement in these structures. However, to realize their full potential, high quality nanowires, whose emission at low temperatures is dominated by free exciton emission, need to be synthesized. In addition, a proper understanding of their complex optical properties, including light-matter coupling in these subwavelength structures, is required. We have synthesized very high-quality wurztite CdS nanowires capped with a 5 nm SiO(2) conformal coating with diameters spanning 100-300 nm using physical vapor and atomic layer deposition techniques and characterized their spatially resolved photoluminescence over the 77-298 K temperature range. In addition to the Fabry-Pérot resonator modulated emission from the ends of the wires, the low temperature emission from the center of the wire shows clear free excitonic peaks and LO phonon replicas, persisting up to room-temperature in the passivated wires. From laser scanning measurements we determined the absorption in the vicinity of the excitonic resonances. In addition to demonstrating the high optical quality of the nanowire crystals, these results provide the fundamental parameters for strong light-matter coupling studies, potentially leading to low threshold polariton lasers, sensitive sensors and optical switches at the nanoscale. PMID:21214218

  11. Characterization of a swept external cavity quantum cascade laser for rapid broadband spectroscopy and sensing.

    Science.gov (United States)

    Brumfield, Brian E; Taubman, Matthew S; Suter, Jonathan D; Phillips, Mark C

    2015-10-01

    The performance of a rapidly swept external cavity quantum cascade laser (ECQCL) system combined with an open-path Herriott cell was evaluated for time-resolved measurements of chemical species with broad and narrow absorption spectra. A spectral window spanning 1278 - 1390 cm(-1) was acquired at a 200 Hz acquisition rate, corresponding to a tuning rate of 2x10(4) cm(-1)/s, with a spectral resolution of 0.2 cm(-1). The capability of the ECQCL to measure < 100 ppbv changes in nitrous oxide (N(2)O) and 1,1,1,2-tetrafluoroethane (F134A) concentrations on millisecond timescales was demonstrated in simulated plume studies with releases near the open-path Herriott cell. Absorbance spectra measured using the ECQCL system exhibited noise-equivalent absorption coefficients of 5x10(-9) cm(-1)Hz(-1/2). For a spectrum acquisition time of 5 ms, noise-equivalent concentrations (NEC) for N(2)O and F134A were measured to be 70 and 16 ppbv respectively, which improved to sub-ppbv levels with averaging to 100 s. Noise equivalent column densities of 0.64 and 0.25 ppmv × m in 1 sec are estimated for N(2)O and F134A. PMID:26480072

  12. Rabi Spectroscopy and Excitation in a Gravity Cavity of Neutron Matter Waves

    International Nuclear Information System (INIS)

    Full text: Gravity experiments might provide an answer for the 'big questions' about space, time, and a unification of all forces, where - as most physicists believe - space-time is not restricted to four dimensions. Hypothetical extra-dimensions, curled up to cylinders or tori with a small compactification radius should lead to deviations from Newton's gravitational law at very small distances. These ideas triggered gravity experiments of different kinds, which in the past ten years have validated Newton's gravitational law down to about 50 μm. The basic problem in searching for new physics at small distances is that the size of the objects under study must be reduced, too, going along with a reduction of signal intensity. At the same time, the electrostatic background increases. Our way out is the interaction of a macroscopic system, here a mirror for neutron reflection, with a pure quantum mechanical system, i.e. the excitation of bound quantum states of a neutron in the gravity potential of the earth. We demonstrate that the method of Rabi spectroscopy usually used in atom optics can now be applied to quantum states in the gravity potential of the earth together with a mechanical or magnetic coupling. This technique allows a precise measurement of quantum mechanical phase shifts of a Schroedinger wave packet bouncing off a hard surface in the gravitational field of the earth. The idea behind this method is that phase shifts in gravity potentials can be related to frequency measurements with unprecedented accuracy. These spectroscopy experiments on gravitation within the Bounce measurements are a starting point for experiments linked to string theories with large volume compactifications and/or cosmology because Newtonian gravity and hypothetical fifth forces evolve with different phase information and limits on a hypothetical strength can be derived. (author)

  13. Thermal dissociation cavity attenuated phase shift spectroscopy for continuous measurement of total peroxy and organic nitrates in the clean atmosphere

    Science.gov (United States)

    Sadanaga, Yasuhiro; Takaji, Ryo; Ishiyama, Ayana; Nakajima, Kazuo; Matsuki, Atsushi; Bandow, Hiroshi

    2016-07-01

    A thermal dissociation cavity attenuated phase shift spectroscopy (TD-CAPS) instrument was developed for measuring total peroxy nitrates (PNs) and organic nitrates (ONs) concentrations in the clean atmosphere. This instrument is easy to operate and can be applied to continuous measurement of PNs and ONs. A continuously measurable system is convenient to perform observations, especially in remote areas. Three lines (NO2, PNs, and ONs lines) were used for thermal dissociation. The NO2 line contains a quartz tube that is not heated, while the PN and ON lines contain quartz tubes that are heated at 433 K and 633 K, respectively. The concentrations of NO2, NO2 + PNs, and NO2 + PNs + ONs can be obtained from the NO2, PN, and ON lines, respectively. The lower limit values of the detection limit (3σ) for PNs and ONs were estimated to be 21 parts per trillion by volume with an integration time of 2 min. PNs were selectively thermally decomposed in the PNs line and formed NO2 quantitatively. In the ONs line, both PNs and ONs were thermally decomposed to produce NO2 quantitatively, but partial decomposition of HNO3 at 633 K interfered with the ONs measurement. Therefore, a HNO3 scrubber is required before the ONs line. Continuous observations were conducted with the TD-CAPS instrument in a remote area, and the instrument performed well for obtaining PNs and ONs concentrations.

  14. An acetone breath analyzer using cavity ringdown spectroscopy: an initial test with human subjects under various situations

    Science.gov (United States)

    Wang, Chuji; Surampudi, Anand B.

    2008-10-01

    We have developed a portable breath acetone analyzer using cavity ringdown spectroscopy (CRDS). The instrument was initially tested by measuring the absorbance of breath gases at a single wavelength (266 nm) from 32 human subjects under various conditions. A background subtraction method, implemented to obtain absorbance differences, from which an upper limit of breath acetone concentration was obtained, is described. The upper limits of breath acetone concentration in the four Type 1 diabetes (T1D) subjects, tested after a 14 h overnight fast, range from 0.80 to 3.97 parts per million by volume (ppmv), higher than the mean acetone concentration (0.49 ppmv) in non-diabetic healthy breath reported in the literature. The preliminary results show that the instrument can tell distinctive differences between the breath from individuals who are healthy and those with T1D. On-line monitoring of breath gases in healthy people post-exercise, post-meals and post-alcohol-consumption was also conducted. This exploratory study demonstrates the first CRDS-based acetone breath analyzer and its potential application for point-of-care, non-invasive, diabetic monitoring.

  15. An acetone breath analyzer using cavity ringdown spectroscopy: an initial test with human subjects under various situations

    International Nuclear Information System (INIS)

    We have developed a portable breath acetone analyzer using cavity ringdown spectroscopy (CRDS). The instrument was initially tested by measuring the absorbance of breath gases at a single wavelength (266 nm) from 32 human subjects under various conditions. A background subtraction method, implemented to obtain absorbance differences, from which an upper limit of breath acetone concentration was obtained, is described. The upper limits of breath acetone concentration in the four Type 1 diabetes (T1D) subjects, tested after a 14 h overnight fast, range from 0.80 to 3.97 parts per million by volume (ppmv), higher than the mean acetone concentration (0.49 ppmv) in non-diabetic healthy breath reported in the literature. The preliminary results show that the instrument can tell distinctive differences between the breath from individuals who are healthy and those with T1D. On-line monitoring of breath gases in healthy people post-exercise, post-meals and post-alcohol-consumption was also conducted. This exploratory study demonstrates the first CRDS-based acetone breath analyzer and its potential application for point-of-care, non-invasive, diabetic monitoring

  16. External-Cavity Quantum Cascade Laser Spectroscopy for Mid-IR Transmission Measurements of Proteins in Aqueous Solution.

    Science.gov (United States)

    Alcaráz, Mirta R; Schwaighofer, Andreas; Kristament, Christian; Ramer, Georg; Brandstetter, Markus; Goicoechea, Héctor; Lendl, Bernhard

    2015-07-01

    In this work, we report mid-IR transmission measurements of the protein amide I band in aqueous solution at large optical paths. A tunable external-cavity quantum cascade laser (EC-QCL) operated in pulsed mode at room temperature allowed one to apply a path length of up to 38 μm, which is four times larger than that applicable with conventional FT-IR spectrometers. To minimize temperature-induced variations caused by background absorption of the ν2-vibration of water (HOH-bending) overlapping with the amide I region, a highly stable temperature control unit with relative temperature stability within 0.005 °C was developed. An advanced data processing protocol was established to overcome fluctuations in the fine structure of the emission curve that are inherent to the employed EC-QCL due to its mechanical instabilities. To allow for wavenumber accuracy, a spectral calibration method has been elaborated to reference the acquired IR spectra to the absolute positions of the water vapor absorption bands. Employing this setup, characteristic spectral features of five well-studied proteins exhibiting different secondary structures could be measured at concentrations as low as 2.5 mg mL(-1). This concentration range could previously only be accessed by IR measurements in D2O. Mathematical evaluation of the spectral overlap and comparison of second derivative spectra confirm excellent agreement of the QCL transmission measurements with protein spectra acquired by FT-IR spectroscopy. This proves the potential of the applied setup to monitor secondary structure changes of proteins in aqueous solution at extended optical path lengths, which allow experiments in flow through configuration. PMID:26059222

  17. Defect detection inside superconducting 1.3 GHz cavities by means of x-ray fluorescence spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Bertucci, M.; Michelato, P.; Moretti, M. [INFN Milano–LASA, Segrate, MI (Italy); Navitski, A. [DESY, Hamburg (Germany); Pagani, C. [INFN Milano–LASA, Segrate, MI (Italy); Dipartimento di Fisica, Università degli Studi di Milano, via Celoria 16, Milano (Italy)

    2016-01-15

    X-ray fluorescence probe for detection of foreign material inclusions on the inner surface of superconducting cavities has been developed and tested. The setup detects trace element content such as a few micrograms of impurities responsible for thermal breakdown phenomena limiting the cavity performance. The setup has been customized for the geometry of 1.3 GHz TESLA-type niobium cavities and focuses on the surface of equator area at around 103 mm from the centre axis of the cavities with around 20 mm detection spot. More precise localization of inclusions can be reconstructed by means of angular or lateral displacement of the cavity. Preliminary tests confirmed a very low detection limit for elements laying in the high efficiency spectrum zone (from 5 to 10 keV), and a high angular resolution allowing an accurate localization of defects within the equator surface.

  18. Defect detection inside superconducting 1.3 GHz cavities by means of x-ray fluorescence spectroscopy

    Science.gov (United States)

    Bertucci, M.; Michelato, P.; Moretti, M.; Navitski, A.; Pagani, C.

    2016-01-01

    X-ray fluorescence probe for detection of foreign material inclusions on the inner surface of superconducting cavities has been developed and tested. The setup detects trace element content such as a few micrograms of impurities responsible for thermal breakdown phenomena limiting the cavity performance. The setup has been customized for the geometry of 1.3 GHz TESLA-type niobium cavities and focuses on the surface of equator area at around 103 mm from the centre axis of the cavities with around 20 mm detection spot. More precise localization of inclusions can be reconstructed by means of angular or lateral displacement of the cavity. Preliminary tests confirmed a very low detection limit for elements laying in the high efficiency spectrum zone (from 5 to 10 keV), and a high angular resolution allowing an accurate localization of defects within the equator surface.

  19. Defect detection inside superconducting 1.3 GHz cavities by means of x-ray fluorescence spectroscopy

    International Nuclear Information System (INIS)

    X-ray fluorescence probe for detection of foreign material inclusions on the inner surface of superconducting cavities has been developed and tested. The setup detects trace element content such as a few micrograms of impurities responsible for thermal breakdown phenomena limiting the cavity performance. The setup has been customized for the geometry of 1.3 GHz TESLA-type niobium cavities and focuses on the surface of equator area at around 103 mm from the centre axis of the cavities with around 20 mm detection spot. More precise localization of inclusions can be reconstructed by means of angular or lateral displacement of the cavity. Preliminary tests confirmed a very low detection limit for elements laying in the high efficiency spectrum zone (from 5 to 10 keV), and a high angular resolution allowing an accurate localization of defects within the equator surface

  20. Light emitting diode cavity enhanced differential optical absorption spectroscopy (LED-CE-DOAS): a novel technique for monitoring atmospheric trace gases

    Science.gov (United States)

    Thalman, Ryan M.; Volkamer, Rainer M.

    2009-08-01

    The combination of Cavity Enhanced Absorption Spectroscopy (CEAS) with broad-band light sources (e.g. Light- Emitting Diodes, LEDs) lends itself to the application of cavity enhanced DOAS (CE-DOAS) to perform sensitive and selective point measurements of multiple trace gases with a single instrument. In contrast to other broad-band CEAS techniques, CE-DOAS relies only on the measurement of relative intensity changes, i.e., does not require knowledge of the light intensity in the absence of trace gases and aerosols (I0). We have built a prototype LED-CE-DOAS instrument in the blue spectral range (420-490nm) to measure nitrogen dioxide (NO2), glyoxal (CHOCHO), iodine monoxide (IO), water (H2O) and oxygen dimers (O4). Aerosol extinction is retrieved at two wavelengths by means of observing water and O4 and measuring pressure, temperature and relative humidity independently. The instrument components are presented, and the approach to measure aerosol extinction is demonstrated by means of a set of experiments where laboratory generated monodisperse aerosols are added to the cavity. The aerosol extinction cross section agrees well with Mie calculations, demonstrating that our setup enables measurements of the above gases in open cavity mode.

  1. A compact and stable eddy covariance set-up for methane measurements using off-axis integrated cavity output spectroscopy

    Directory of Open Access Journals (Sweden)

    D. M. D. Hendriks

    2008-01-01

    Full Text Available A Fast Methane Analyzer (FMA is assessed for its applicability in a closed path eddy covariance field set-up in a peat meadow. The FMA uses off-axis integrated cavity output spectroscopy combined with a highly specific narrow band laser for the detection of CH4 and strongly reflective mirrors to obtain a laser path length of 2–20×103 m. Statistical testing and a calibration experiment showed high precision (7.8×10−3 ppb and accuracy (<0.30% of the instrument, while no drift was observed. The instrument response time was determined to be 0.10 s. In the field set-up, the FMA is attached to a scroll pump and combined with a 3-axis ultrasonic anemometer and an open path infrared gas analyzer for measurements of carbon dioxide and water vapour. The power-spectra and co-spectra of the instruments were satisfactory for 10 Hz sampling rates.

    Due to erroneous measurements, spikes and periods of low turbulence the data series consisted for 26% of gaps. Observed CH4 fluxes consisted mainly of emission, showed a diurnal cycle, but were rather variable over. The average CH4 emission was 29.7 nmol m−2 s−1, while the typical maximum CH4 emission was approximately 80.0 nmol m−2 s−1 and the typical minimum flux was approximately 0.0 nmol m−2 s−1. The correspondence of the measurements with flux chamber measurements in the footprint was good and the observed CH4 emission rates were comparable with eddy covariance CH4 measurements in other peat areas.

    Additionally, three measurement techniques with lower sampling frequencies were simulated, which might give the possibility to measure CH4 fluxes without an external pump and save energy. Disjunct eddy covariance appeared to be the most reliable substitute for 10 Hz eddy covariance, while relaxed eddy accumulation gave

  2. A compact and stable eddy covariance set-up for methane measurements using off-axis integrated cavity output spectroscopy

    Directory of Open Access Journals (Sweden)

    D. M. D. Hendriks

    2007-08-01

    Full Text Available A DLT-100 Fast Methane Analyser (FMA from Los Gatos Research (LGR Ltd. is assessed for its applicability in a closed path eddy covariance field set-up. The FMA uses off-axis integrated cavity output spectroscopy (ICOS combined with a highly specific narrow band laser for the detection of CH4 and strongly reflective mirrors to obtain a laser path length of 2×10³ to 20×10³ m. Statistical testing, a calibration experiment and comparison with high tower data showed high precision and very good stability of the instrument. The measurement cell response time was tested to be 0.10 s. In the field set-up, the FMA is attached to a scroll pump and combined with a Gill Windmaster Pro 3 axis Ultrasonic Anemometer and a Licor 7500 open path infrared gas analyzer. The power-spectra and co-spectra of the instrument are satisfactory for 10 Hz sampling rates. The correspondence with CH4 flux chamber measurements is good and the observed CH4 emissions are comparable with (eddy covariance CH4 measurements in other peat areas.

    CH4 emissions are rather variable over time and show a diurnal pattern. The average CH4 emission is 50±12.5 nmol m−2 s−1, while the typical maximum CH4 emission is 120±30 nmol m−2 s−1 (during daytime and the typical minimum flux is –20±2.5 nmol m−2 s−1 (uptake, during night time.

    Additionally, the set-up was tested for three measurement techniques with slower measurement rates, which could be used in the future to make the scroll pump superfluous and save energy. Both disjunct eddy covariance as well as slow 1 Hz eddy covariance showed results very similar to normal 10 Hz eddy covariance. Relaxed eddy accumulation (REA only matched with normal 10 Hz eddy covariance over an averaging period of at least several weeks.

  3. Frequency Modulated Integrated Cavity Output Spectroscopy: A General Technique for Trace Gas and Isotope Measurements with Unprecedented Sensitivity Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A new technique is proposed for improved trace gas detection and measurement that combines the high absorption depths afforded by mid-infrared Integrated Cavity...

  4. QCL - Optical-Feedback Cavity Enhanced Absorption Spectroscopy For The Analysis Of Atmospheric 13CO2/12CO2 In Ice-Core Gas Bubbles

    Science.gov (United States)

    Gorrotxategi Carbajo, Paula; Romanini, Daniele; Maisons, Gregory; Carras, Mathieu; Chappellaz, Jerome; Kerstel, Erik

    2013-04-01

    In the context of a globally warming climate it is crucial to study the climate variability in the past and to understand the underlying mechanisms. The composition of gas stored in bubbles in polar ice presents a paleo-climate archive that provides a powerful means to study the exact mechanisms involved in the ~40% increase in the atmospheric CO2 concentration between glacial and interglacial climates. It is particularly important to understand such natural coupling between climate and the carbon cycle, as it will partly determine what natural feedback can be expected on the atmospheric CO2 concentration in a future warmer world. The source of the CO2 released into the atmosphere during previous deglaciations can be constrained from isotopic measurements by the fact that the different CO2 reservoirs (terrestrial biosphere, oceans) and associated mechanisms (biological or physical) have different isotopic signatures. Unfortunately, such isotope studies have been seriously hampered by the experimental difficulty of extracting the CO2 without contamination or fractionation, and measuring the isotope signal off-line on an isotope ratio mass spectrometer (IRMS). Here we present an alternative method that leverages the extreme sensitivity afforded by Optical Feedback Cavity Enhanced Absorption Spectroscopy (OF-CEAS) in the Mid-Infrared [1]. This region of the spectrum is accessed by a custom-developed Quantum Cascade Laser operating near 4.35 µm. The feedback to the laser of light that has been spectrally filtered by a high-finesse, V-shaped enhancement cavity has the effect of spectrally narrowing the laser emission and to auto-lock the laser frequency to one of the cavity's longitudinal modes, with clear advantages in terms of acquisition time and signal-to-noise ratio of the measurement. The line strengths in this region are about 5 orders of magnitude higher than in the more easily accessible NIR region near 1.6 µm and about 1000 times higher than at 2 µm. The

  5. Analysis of two stacked cylindrical dielectric resonators in a TE₁₀₂ microwave cavity for magnetic resonance spectroscopy.

    Science.gov (United States)

    Mattar, Saba M; Elnaggar, Sameh Y

    2011-04-01

    The frequency, field distributions and filling factors of a DR/TE₁₀₂ probe, consisting of two cylindrical dielectric resonators (DR1 and DR2) in a rectangular TE₁₀₂ cavity, are simulated and analyzed by finite element methods. The TE(+++) mode formed by the in-phase coupling of the TE₀₁(δ)(DR1), TE₀₁(δ)(DR2) and TE₁₀₂ basic modes, is the most appropriate mode for X-band EPR experiments. The corresponding simulated B(+++) fields of the TE(+++) mode have significant amplitudes at DR1, DR2 and the cavity's iris resulting in efficient coupling between the DR/TE₁₀₂ probe and the microwave bridge. At the experimental configuration, B(+++) in the vicinity of DR2 is much larger than that around DR1 indicating that DR1 mainly acts as a frequency tuner. In contrast to a simple microwave shield, the resonant cavity is an essential component of the probe that affects its frequency. The two dielectric resonators are always coupled and this is enhanced by the cavity. When DR1 and DR2 are close to the cavity walls, the TE(+++) frequency and B(+++) distribution are very similar to that of the empty TE₁₀₂ cavity. When all the experimental details are taken into account, the agreement between the experimental and simulated TE(+++) frequencies is excellent. This confirms that the resonating mode of the spectrometer's DR/TE₁₀₂ probe is the TE(+++) mode. Additional proof is obtained from B₁(x), which is the calculated maximum x component of B(+++). It is predominantly due to DR2 and is approximately 4.4 G. The B₁(x) maximum value of the DR/TE₁₀₂ probe is found to be slightly larger than that for a single resonator in a cavity because DR1 further concentrates the cavity's magnetic field along its x axis. Even though DR1 slightly enhances the performance of the DR/TE₁₀₂ probe its main benefit is to act as a frequency tuner. A waveguide iris can be used to over-couple the DR/TE₁₀₂ probe and lower its Q to ≈150. Under

  6. Analysis of two stacked cylindrical dielectric resonators in a TE 102 microwave cavity for magnetic resonance spectroscopy

    Science.gov (United States)

    Mattar, Saba M.; ElNaggar, Sameh Y.

    2011-04-01

    The frequency, field distributions and filling factors of a DR/TE 102 probe, consisting of two cylindrical dielectric resonators (DR1 and DR2) in a rectangular TE 102 cavity, are simulated and analyzed by finite element methods. The TE +++ mode formed by the in-phase coupling of the TE 01δ(DR1), TE 01δ(DR2) and TE 102 basic modes, is the most appropriate mode for X-band EPR experiments. The corresponding simulated B +++ fields of the TE +++ mode have significant amplitudes at DR1, DR2 and the cavity's iris resulting in efficient coupling between the DR/TE 102 probe and the microwave bridge. At the experimental configuration, B +++ in the vicinity of DR2 is much larger than that around DR1 indicating that DR1 mainly acts as a frequency tuner. In contrast to a simple microwave shield, the resonant cavity is an essential component of the probe that affects its frequency. The two dielectric resonators are always coupled and this is enhanced by the cavity. When DR1 and DR2 are close to the cavity walls, the TE +++ frequency and B +++ distribution are very similar to that of the empty TE 102 cavity. When all the experimental details are taken into account, the agreement between the experimental and simulated TE +++ frequencies is excellent. This confirms that the resonating mode of the spectrometer's DR/TE 102 probe is the TE +++ mode. Additional proof is obtained from B1x, which is the calculated maximum x component of B +++. It is predominantly due to DR2 and is approximately 4.4 G. The B1x maximum value of the DR/TE 102 probe is found to be slightly larger than that for a single resonator in a cavity because DR1 further concentrates the cavity's magnetic field along its x axis. Even though DR1 slightly enhances the performance of the DR/TE 102 probe its main benefit is to act as a frequency tuner. A waveguide iris can be used to over-couple the DR/TE 102 probe and lower its Q to ≈150. Under these conditions, the probe has a short dead time and a large bandwidth

  7. A tuneable doubly stacked dielectric resonator housed in an intact TE 102 cavity for electron paramagnetic resonance spectroscopy

    Science.gov (United States)

    Mattar, Saba M.; Emwas, Abdul H.

    2003-01-01

    An EPR resonator is constructed by inserting a pair of dielectric ceramic rings in an unmodified rectangular TE 102 cavity. It is tuneable over the range of 8.0-10.0 GHz. Therefore, existing EPR cavities can be easily converted to resonators with superior signal-to-noise ratios that are at least 24 times larger than the original ones in this extended frequency range. The resonator's performance is tested using DPPH, TEMPONE, MnO and Cu 2+ complexes and displays excellent resolution and sensitivity. Thus EPR spectra of small paramagnetic organic and inorganic samples and spin labeled biomolecules may be obtained without resorting to loop gap resonators.

  8. Cavity-enhanced absorption spectroscopy with a ps-pulsed UV laser for sensitive, high-speed measurements in a shock tube.

    Science.gov (United States)

    Wang, Shengkai; Sun, Kai; Davidson, David F; Jeffries, Jay B; Hanson, Ronald K

    2016-01-11

    We report the first application of cavity-enhanced absorption spectroscopy (CEAS) with a ps-pulsed UV laser for sensitive and rapid gaseous species time-history measurements in a transient environment (in this study, a shock tube). The broadband nature of the ps pulses enabled instantaneous coupling of the laser beam into roughly a thousand cavity modes, which grants excellent immunity to laser-cavity coupling noise in environments with heavy vibrations, even with an on-axis alignment. In this proof-of-concept experiment, we demonstrated an absorption gain of 49, which improved the minimum detectable absorbance by ~20 compared to the conventional single-pass strategy at similar experimental conditions. For absorption measurements behind reflected shock waves, an effective time-resolution of ~2 μs was achieved, which enabled time-resolved observations of transient phenomena, such as the vibrational relaxation of O(2) demonstrated here. The substantial improvement in detection sensitivity, together with microsecond measurement resolution implies excellent potential for studies of transient physical and chemical processes in nonequilibrium situations, particularly via measurements of weak absorptions of trace species in dilute reactive systems. PMID:26832262

  9. Following interfacial kinetics in real time using broadband evanescent wave cavity-enhanced absorption spectroscopy: a comparison of light-emitting diodes and supercontinuum sources.

    Science.gov (United States)

    van der Sneppen, Lineke; Hancock, Gus; Kaminski, Clemens; Laurila, Toni; Mackenzie, Stuart R; Neil, Simon R T; Peverall, Robert; Ritchie, Grant A D; Schnippering, Mathias; Unwin, Patrick R

    2010-01-01

    A white light-emitting diode (LED) with emission between 420 and 700 nm and a supercontinuum (SC) source with emission between 450 and 2500 nm have been compared for use in evanescent wave broadband cavity-enhanced absorption spectroscopy (EW-BB-CEAS). The method is calibrated using a dye with known absorbance. While the LED is more economic as an excitation source, the SC source is superior both in terms of baseline noise (noise equivalent absorbances lower than 10(-5) compared to 10(-4) absorbance units (a.u.)) and accuracy of the measurement; these baseline noise levels are comparable to evanescent wave cavity ringdown spectroscopy (EW-CRDS) studies while the accessible spectral region of EW-BB-CEAS is much larger (420-750 nm in this study, compared to several tens of nanometres for EW-CRDS). The improvements afforded by the use of an SC source in combination with a high sensitivity detector are demonstrated in the broadband detection of electrogenerated Ir(IV) complexes in a thin-layer electrochemical cell arrangement. Excellent signal to noise is achieved with 10 micros signal accumulation times at a repetition rate of 600 Hz, easily fast enough to follow, in real time, solution kinetics and interfacial processes. PMID:20024193

  10. Enhancing the sensitivity of mid-IR quantum cascade laser-based cavity-enhanced absorption spectroscopy using RF current perturbation.

    Science.gov (United States)

    Manfred, Katherine M; Kirkbride, James M R; Ciaffoni, Luca; Peverall, Robert; Ritchie, Grant A D

    2014-12-15

    The sensitivity of mid-IR quantum cascade laser (QCL) off-axis cavity-enhanced absorption spectroscopy (CEAS), often limited by cavity mode structure and diffraction losses, was enhanced by applying a broadband RF noise to the laser current. A pump-probe measurement demonstrated that the addition of bandwidth-limited white noise effectively increased the laser linewidth, thereby reducing mode structure associated with CEAS. The broadband noise source offers a more sensitive, more robust alternative to applying single-frequency noise to the laser. Analysis of CEAS measurements of a CO(2) absorption feature at 1890  cm(-1) averaged over 100 ms yielded a minimum detectable absorption of 5.5×10(-3)  Hz(-1/2) in the presence of broadband RF perturbation, nearly a tenfold improvement over the unperturbed regime. The short acquisition time makes this technique suitable for breath applications requiring breath-by-breath gas concentration information. PMID:25503003

  11. Fluorescence spectroscopy for the detection of potentially malignant disorders of the oral cavity: analysis of 30 cases

    Science.gov (United States)

    Francisco, A. L. N.; Correr, W. R.; Azevedo, L. H.; Galletta, V. K.; Pinto, C. A. L.; Kowalski, L. P.; Kurachi, C.

    2014-01-01

    Oral cancer is a major health problem worldwide and although early diagnosis of potentially malignant and malignant diseases is associated with better treatment results, a large number of cancers are initially misdiagnosed, with unfortunate consequences for long-term survival. Fluorescence spectroscopy is a noninvasive modality of diagnostic approach using induced fluorescence emission in tumors that can improve diagnostic accuracy. The objective of this study was to determine the ability to discriminate between normal oral mucosa and potentially malignant disorders by fluorescence spectroscopy. Fluorescence investigation under 408 and 532 nm excitation wavelengths was performed on 60 subjects, 30 with potentially malignant disorders and 30 volunteers with normal mucosa. Data was analyzed to correlate fluorescence patterns with clinical and histopathological diagnostics. Fluorescence spectroscopy used as a point measurement technique resulted in a great variety of spectral information. In a qualitative analysis of the fluorescence spectral characteristics of each type of injury evaluated, it was possible to discriminate between normal and abnormal oral mucosa. The results show the potential use of fluorescence spectroscopy for an improved discrimination of oral disorders.

  12. Fluorescence spectroscopy for the detection of potentially malignant disorders of the oral cavity: analysis of 30 cases

    International Nuclear Information System (INIS)

    Oral cancer is a major health problem worldwide and although early diagnosis of potentially malignant and malignant diseases is associated with better treatment results, a large number of cancers are initially misdiagnosed, with unfortunate consequences for long-term survival. Fluorescence spectroscopy is a noninvasive modality of diagnostic approach using induced fluorescence emission in tumors that can improve diagnostic accuracy. The objective of this study was to determine the ability to discriminate between normal oral mucosa and potentially malignant disorders by fluorescence spectroscopy. Fluorescence investigation under 408 and 532 nm excitation wavelengths was performed on 60 subjects, 30 with potentially malignant disorders and 30 volunteers with normal mucosa. Data was analyzed to correlate fluorescence patterns with clinical and histopathological diagnostics. Fluorescence spectroscopy used as a point measurement technique resulted in a great variety of spectral information. In a qualitative analysis of the fluorescence spectral characteristics of each type of injury evaluated, it was possible to discriminate between normal and abnormal oral mucosa. The results show the potential use of fluorescence spectroscopy for an improved discrimination of oral disorders. (paper)

  13. A 23.75-GHz frequency comb with two low-finesse filtering cavities in series for high resolution spectroscopy

    Institute of Scientific and Technical Information of China (English)

    侯磊; 韩海年; 王薇; 张龙; 庞利辉; 李德华; 魏志义

    2015-01-01

    A laser frequency comb with several tens GHz level is demonstrated, based on an Yb-doped femtosecond fiber laser and two low-finesse Fabry–P´erot cavities (FPCs) in series. The original 250-MHz mode-line-spacing of the source comb is filtered to 4.75 GHz and 23.75 GHz, respectively. According to the multi-beam interferences theory of FPC, the side-mode suppression rate of FPC schemes is in good agreement with our own theoretical results from 27 dB of a single FPC to 43 dB of paired FPCs. To maintain long-term stable operation and determine the absolute frequency mode number in the 23.75-GHz comb, the Pound–Drever–Hall (PDH) locking technology is utilized. Such stable tens GHz frequency combs have important applications in calibrating astronomical spectrographs with high resolution.

  14. A 23.75-GHz frequency comb with two low-finesse filtering cavities in series for high resolution spectroscopy

    International Nuclear Information System (INIS)

    A laser frequency comb with several tens GHz level is demonstrated, based on a Yb-doped femtosecond fiber laser and two low-finesse Fabry–Pérot cavities (FPCs) in series. The original 250-MHz mode-line-spacing of the source comb is filtered to 4.75 GHz and 23.75 GHz, respectively. According to the multi-beam interferences theory of FPC, the side-mode suppression rate of FPC schemes is in good agreement with our own theoretical results from 27 dB of a single FPC to 43 dB of paired FPCs. To maintain long-term stable operation and determine the absolute frequency mode number in the 23.75-GHz comb, the Pound–Drever–Hall (PDH) locking technology is utilized. Such stable tens GHz frequency combs have important applications in calibrating astronomical spectrographs with high resolution. (paper)

  15. Spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Hellman, Hal

    1968-01-01

    This booklet discusses spectroscopy, the study of absorption of radiation by matter, including X-ray, gamma-ray, microwave, mass spectroscopy, as well as others. Spectroscopy has produced more fundamental information to the study of the detailed structure of matter than any other tools.

  16. Molecular frequency reference at 1.56  μm using a 12C16O overtone transition with the noise-immune cavity-enhanced optical heterodyne molecular spectroscopy method.

    Science.gov (United States)

    Saraf, Shailendhar; Berceau, Paul; Stochino, Alberto; Byer, Robert; Lipa, John

    2016-05-15

    We report on a molecular clock based on the interrogation of the 3ν rotational-vibrational combination band at 1563 nm of carbon monoxide C1612O. The laser stabilization scheme is based on the noise-immune cavity-enhanced optical heterodyne molecular spectroscopy (NICE-OHMS) technique in frequency modulation (FM) saturation spectroscopy. We use a high-finesse ultra-low expansion (ULE) glass optical cavity with CO as the molecular reference for long-term stabilization of the cavity resonance. We report an Allan deviation of 1.8×10-12 at 1 s that improves to ∼3.5×10-14 with 1000 s of averaging. PMID:27176959

  17. Spectroscopy

    CERN Document Server

    Walker, S

    1976-01-01

    The three volumes of Spectroscopy constitute the one comprehensive text available on the principles, practice and applications of spectroscopy. By giving full accounts of those spectroscopic techniques only recently introduced into student courses - such as Mössbauer spectroscopy and photoelectron spectroscopy - in addition to those techniques long recognised as being essential in chemistry teaching - sucha as e.s.r. and infrared spectroscopy - the book caters for the complete requirements of undergraduate students and at the same time provides a sound introduction to special topics for graduate students.

  18. Application of Cavity Enhanced Absorption Spectroscopy to the Detection of Nitric Oxide, Carbonyl Sulphide, and Ethane—Breath Biomarkers of Serious Diseases

    Directory of Open Access Journals (Sweden)

    Jacek Wojtas

    2015-06-01

    Full Text Available The paper presents one of the laser absorption spectroscopy techniques as an effective tool for sensitive analysis of trace gas species in human breath. Characterization of nitric oxide, carbonyl sulphide and ethane, and the selection of their absorption lines are described. Experiments with some biomarkers showed that detection of pathogenic changes at the molecular level is possible using this technique. Thanks to cavity enhanced spectroscopy application, detection limits at the ppb-level and short measurements time (<3 s were achieved. Absorption lines of reference samples of the selected volatile biomarkers were probed using a distributed feedback quantum cascade laser and a tunable laser system consisting of an optical parametric oscillator and difference frequency generator. Setup using the first source provided a detection limit of 30 ppb for nitric oxide and 250 ppb for carbonyl sulphide. During experiments employing a second laser, detection limits of 0.9 ppb and 0.3 ppb were obtained for carbonyl sulphide and ethane, respectively. The conducted experiments show that this type of diagnosis would significantly increase chances for effective therapy of some diseases. Additionally, it offers non-invasive and real time measurements, high sensitivity and selectivity as well as minimizing discomfort for patients. For that reason, such sensors can be used in screening for early detection of serious diseases.

  19. Infrared Scattering Scanning Near-Field Optical Microscopy Using An External Cavity Quantum Cascade Laser For Nanoscale Chemical Imaging And Spectroscopy of Explosive Residues

    Energy Technology Data Exchange (ETDEWEB)

    Craig, Ian M.; Phillips, Mark C.; Taubman, Matthew S.; Josberger, Erik E.; Raschke, Markus Bernd

    2013-02-04

    Infrared scattering scanning near-field optical microscopy (s-SNOM) is an apertureless superfocusing technique that uses the antenna properties of a conducting atomic force microscope (AFM) tip to achieve infrared spatial resolution below the diffraction limit. The instrument can be used either in imaging mode, where a fixed wavelength light source is tuned to a molecular resonance and the AFM raster scans an image, or in spectroscopy mode where the AFM is held stationary over a feature of interest and the light frequency is varied to obtain a spectrum. In either case, a strong, stable, coherent infrared source is required. Here we demonstrate the integration of a broadly tunable external cavity quantum cascade laser (ECQCL) into an s-SNOM and use it to obtain infrared spectra of microcrystals of chemicals adsorbed onto gold substrates. Residues of the explosive compound tetryl was deposited onto gold substrates. s-SNOM experiments were performed in the 1260-1400 cm−1 tuning range of the ECQCL, corresponding to the NO2 symmetric stretch vibrational fingerprint region. Vibrational infrared spectra were collected on individual chemical domains with a collection area of *500nm2 and compared to ensemble averaged far-field reflection-absorption infrared spectroscopy (RAIRS) results.

  20. Application of Cavity Enhanced Absorption Spectroscopy to the Detection of Nitric Oxide, Carbonyl Sulphide, and Ethane--Breath Biomarkers of Serious Diseases.

    Science.gov (United States)

    Wojtas, Jacek

    2015-01-01

    The paper presents one of the laser absorption spectroscopy techniques as an effective tool for sensitive analysis of trace gas species in human breath. Characterization of nitric oxide, carbonyl sulphide and ethane, and the selection of their absorption lines are described. Experiments with some biomarkers showed that detection of pathogenic changes at the molecular level is possible using this technique. Thanks to cavity enhanced spectroscopy application, detection limits at the ppb-level and short measurements time (quantum cascade laser and a tunable laser system consisting of an optical parametric oscillator and difference frequency generator. Setup using the first source provided a detection limit of 30 ppb for nitric oxide and 250 ppb for carbonyl sulphide. During experiments employing a second laser, detection limits of 0.9 ppb and 0.3 ppb were obtained for carbonyl sulphide and ethane, respectively. The conducted experiments show that this type of diagnosis would significantly increase chances for effective therapy of some diseases. Additionally, it offers non-invasive and real time measurements, high sensitivity and selectivity as well as minimizing discomfort for patients. For that reason, such sensors can be used in screening for early detection of serious diseases. PMID:26091398

  1. Application of Cavity Enhanced Absorption Spectroscopy to the Detection of Nitric Oxide, Carbonyl Sulphide, and Ethane—Breath Biomarkers of Serious Diseases

    Science.gov (United States)

    Wojtas, Jacek

    2015-01-01

    The paper presents one of the laser absorption spectroscopy techniques as an effective tool for sensitive analysis of trace gas species in human breath. Characterization of nitric oxide, carbonyl sulphide and ethane, and the selection of their absorption lines are described. Experiments with some biomarkers showed that detection of pathogenic changes at the molecular level is possible using this technique. Thanks to cavity enhanced spectroscopy application, detection limits at the ppb-level and short measurements time (quantum cascade laser and a tunable laser system consisting of an optical parametric oscillator and difference frequency generator. Setup using the first source provided a detection limit of 30 ppb for nitric oxide and 250 ppb for carbonyl sulphide. During experiments employing a second laser, detection limits of 0.9 ppb and 0.3 ppb were obtained for carbonyl sulphide and ethane, respectively. The conducted experiments show that this type of diagnosis would significantly increase chances for effective therapy of some diseases. Additionally, it offers non-invasive and real time measurements, high sensitivity and selectivity as well as minimizing discomfort for patients. For that reason, such sensors can be used in screening for early detection of serious diseases. PMID:26091398

  2. Short-lived species detection of nitrous acid by external-cavity quantum cascade laser based quartz-enhanced photoacoustic absorption spectroscopy

    International Nuclear Information System (INIS)

    Spectroscopic detection of short-lived gaseous nitrous acid (HONO) at 1254.85 cm−1 was realized by off-beam coupled quartz-enhanced photoacoustic spectroscopy (QEPAS) in conjunction with an external cavity quantum cascade lasers (EC-QCL). High sensitivity monitoring of HONO was performed within a very small gas-sample volume (of ∼40 mm3) allowing a significant reduction (of about 4 orders of magnitude) of air sampling residence time which is highly desired for accurate quantification of chemically reactive short-lived species. Calibration of the developed QEPAS-based HONO sensor was carried out by means of lab-generated HONO samples whose concentrations were determined by direct absorption spectroscopy involving a ∼109.5 m multipass cell and a distributed feedback QCL. A minimum detection limit (MDL) of 66 ppbv (1 σ) HONO was achieved at 70 mbar using a laser output power of 50 mW and 1 s integration time, which corresponded to a normalized noise equivalent absorption coefficient of 3.6 × 10−8 cm−1 W/Hz1/2. This MDL was down to 7 ppbv at the optimal integration time of 150 s. The corresponding 1σ minimum detected absorption coefficient is ∼1.1 × 10−7 cm−1 (MDL ∼ 3 ppbv) in 1 s and ∼1.1 × 10−8 cm−1 (MDL ∼ 330 pptv) in 150 s, respectively, with 1 W laser power

  3. Short-lived species detection of nitrous acid by external-cavity quantum cascade laser based quartz-enhanced photoacoustic absorption spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Yi, Hongming [Laboratoire de Physicochimie de l' Atmosphère, Université du Littoral Côte d' Opale, 189A, Av. Maurice Schumann, 59140 Dunkerque (France); Laboratory of Atmospheric Physico-Chemistry, Anhui Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, P.O. Box 1125, 350 Shushanhu Road, Hefei, Anhui 230031 (China); Maamary, Rabih; Fertein, Eric; Chen, Weidong, E-mail: chen@univ-littoral.fr [Laboratoire de Physicochimie de l' Atmosphère, Université du Littoral Côte d' Opale, 189A, Av. Maurice Schumann, 59140 Dunkerque (France); Gao, Xiaoming [Laboratory of Atmospheric Physico-Chemistry, Anhui Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, P.O. Box 1125, 350 Shushanhu Road, Hefei, Anhui 230031 (China); Sigrist, Markus W. [ETH Zurich, Institute for Quantum Electronics, HPT H4.1, Auguste-Piccard-Hof 1, CH-8093 Zürich (Switzerland)

    2015-03-09

    Spectroscopic detection of short-lived gaseous nitrous acid (HONO) at 1254.85 cm{sup −1} was realized by off-beam coupled quartz-enhanced photoacoustic spectroscopy (QEPAS) in conjunction with an external cavity quantum cascade lasers (EC-QCL). High sensitivity monitoring of HONO was performed within a very small gas-sample volume (of ∼40 mm{sup 3}) allowing a significant reduction (of about 4 orders of magnitude) of air sampling residence time which is highly desired for accurate quantification of chemically reactive short-lived species. Calibration of the developed QEPAS-based HONO sensor was carried out by means of lab-generated HONO samples whose concentrations were determined by direct absorption spectroscopy involving a ∼109.5 m multipass cell and a distributed feedback QCL. A minimum detection limit (MDL) of 66 ppbv (1 σ) HONO was achieved at 70 mbar using a laser output power of 50 mW and 1 s integration time, which corresponded to a normalized noise equivalent absorption coefficient of 3.6 × 10{sup −8 }cm{sup −1} W/Hz{sup 1/2}. This MDL was down to 7 ppbv at the optimal integration time of 150 s. The corresponding 1σ minimum detected absorption coefficient is ∼1.1 × 10{sup −7 }cm{sup −1} (MDL ∼ 3 ppbv) in 1 s and ∼1.1 × 10{sup −8 }cm{sup −1} (MDL ∼ 330 pptv) in 150 s, respectively, with 1 W laser power.

  4. Quantitative Determination of Density of Ground State Atomic Oxygen from Both TALIF and Emission Spectroscopy in Hot Air Plasma Generated by Microwave Resonant Cavity

    Science.gov (United States)

    Marchal, F.; Yousfi, M.; Merbahi, N.; Wattieaux, G.; Piquemal, A.

    2016-03-01

    Two experimental techniques have been used to quantify the atomic oxygen density in the case of hot air plasma generated by a microwave (MW) resonant cavity. The latter operates at a frequency of 2.45 GHz inside a cell of gas conditioning at a pressure of 600 mbar, an injected air flow of 12 L/min and an input MW power of 1 kW. The first technique is based on the standard two photon absorption laser induced fluorescence (TALIF) using xenon for calibration but applied for the first time in the present post discharge hot air plasma column having a temperature of about 4500 K near the axis of the nozzle. The second diagnostic technique is an actinometry method based on optical emission spectroscopy (OES). In this case, we compared the spectra intensities of a specific atomic oxygen line (844 nm) and the closest wavelength xenon line (823 nm). The two lines need to be collected under absolutely the same spectroscopic parameters. The xenon emission is due to the addition of a small proportion of xenon (1% Xe) of this chemically inert gas inside the air while a further small quantity of H2 (2%) is also added in the mixture in order to collect OH(A-X) and NH(A-X) spectra without noise. The latter molecular spectra are required to estimate gas and excitation temperatures. Optical emission spectroscopy measurements, at for instance the position z=12 mm on the axis plasma column that leads to a gas measured temperature equal to 3500 K, an excitation temperature of about 9500 K and an atomic oxygen density 2.09×1017±0.2×1017 cm-3. This is in very good agreement with the TALIF measurement, which is equal to 2.0×1017 cm-3.

  5. Mid-infrared concentration-modulated noise-immune cavity-enhanced optical heterodyne molecular spectroscopy of a continuous supersonic expansion discharge source

    Science.gov (United States)

    Talicska, Courtney N.; Porambo, Michael W.; Perry, Adam J.; McCall, Benjamin J.

    2016-06-01

    Concentration-modulated noise-immune cavity-enhanced optical heterodyne molecular spectroscopy (NICE-OHMS) is implemented for the first time on a continuous gas-flow pinhole supersonic expansion discharge source for the study of cooled molecular ions. The instrument utilizes a continuous-wave optical parametric oscillator easily tunable from 2.5 to 3.9 μm and demonstrates a noise equivalent absorption of ˜1 × 10-9 cm-1. The effectiveness of concentration-modulated NICE-OHMS is tested through the acquisition of transitions in the ν1 fundamental band of HN2+ centered near 3234 cm-1, with a signal-to-noise of ˜40 obtained for the strongest transitions. The technique is used to characterize the cooling abilities of the supersonic expansion discharge source itself, and a Boltzmann analysis determines a rotational temperature of ˜29 K for low rotational states of HN2+. Further improvements are discussed that will enable concentration-modulated NICE-OHMS to reach its full potential for the detection of molecular ions formed in supersonic expansion discharges.

  6. Spectroscopy

    DEFF Research Database (Denmark)

    Berg, Rolf W.

    This introductory booklet covers the basics of molecular spectroscopy, infrared and Raman methods, instrumental considerations, symmetry analysis of molecules, group theory and selection rules, as well as assignments of fundamental vibrational modes in molecules.......This introductory booklet covers the basics of molecular spectroscopy, infrared and Raman methods, instrumental considerations, symmetry analysis of molecules, group theory and selection rules, as well as assignments of fundamental vibrational modes in molecules....

  7. Chiroptical Spectroscopy in the Vapor Phase

    Science.gov (United States)

    Lahiri, Priyanka; Long, Benjamin D.; Wiberg, Kenneth B.; Vaccaro, Patrick H.

    2011-06-01

    Electromagnetic radiation propagating through an isotropic chiral medium experiences a complex index of refraction that differs in both real (in-phase) and imaginary (in-quadrature) parts for the right-circular and left-circular polarization states that define the helicity basis. The resulting phenomena of circular birefringence (CB) and circular dichroism (CD) lead to observable effects in the form of dispersive rotation and absorptive elliptization for an impinging beam of plane-polarized light, which commonly are measured under conditions of nonresonant and resonant excitation, respectively. This talk will discuss ongoing efforts designed to elucidate the provenance of electronic optical activity under complementary solvated and isolated conditions, with the latter vapor-phase work made possible by our continuing development of Cavity Ring-Down Polarimetry (CRDP). Molecules of interest include the rigid bicyclic ketone (1R,4R)-norbornenone, where the spatial arrangement of distal alkene and carbonyl moeities gives rise to extraordinarily large specific rotation (CB) parameters that are predicted incongruously by different quantum-chemical methods; the monoterpene constitutional isomers (S)-2-carene and (S)-3-carene, which display surprisingly distinct chiroptical properties; and conjugated ketones such as (S)-verbenone, where CD probes of weak π*←n absorption bands have been performed at vibronic resolution. The disparate nature of gas-phase and condensed-phase optical activity will be highlighted, with complementary ab initio calculations serving to elucidate the structural, chemical, and electronic origins of observed behavior. T. Müller, K. B. Wiberg, P. H. Vaccaro, J. R. Cheeseman, and M. J. Frisch, J. Opt. Soc. Am. B 19, 125 (2002) P. H. Vaccaro, ``Chapter 1.II.10: Optical Rotation and Intrinsic Optical Activity'' in Comprehensive Chiroptical Spectroscopy, N. Berova, P. L. Polavarapu, K. Nakanishi, and R. W. Woody, eds. (John Wiley and Sons, Inc

  8. Superconducting cavities

    International Nuclear Information System (INIS)

    The basic properties of superconducting cavities for electron accelerators are discussed with special emphasis on the following topics: technical motivation for the use of superconducting cavities; surface impedance; the critical field of superconductors; anomalous losses; materials other than niobium; technological achievements for accelerating cavities. (author)

  9. Application of External-Cavity Quantum Cascade Infrared Lasers to Nanosecond Time-Resolved Infrared Spectroscopy of Condensed-Phase Samples Following Pulse Radiolysis

    International Nuclear Information System (INIS)

    Pulse radiolysis, utilizing short pulses of high-energy electrons from accelerators, is a powerful method for rapidly generating reduced or oxidized species and other free radicals in solution. Combined with fast time-resolved spectroscopic detection (typically in the ultraviolet/visible/near-infrared), it is invaluable for monitoring the reactivity of species subjected to radiolysis on timescales ranging from picoseconds to seconds. However, it is often difficult to identify the transient intermediates definitively due to a lack of structural information in the spectral bands. Time-resolved vibrational spectroscopy offers the structural specificity necessary for mechanistic investigations but has received only limited application in pulse radiolysis experiments. For example, time-resolved infrared (TRIR) spectroscopy has only been applied to a handful of gas-phase studies, limited mainly by several technical challenges. We have exploited recent developments in commercial external-cavity quantum cascade laser (EC-QCL) technology to construct a nanosecond TRIR apparatus that has allowed, for the first time, TRIR spectra to be recorded following pulse radiolysis of condensed-phase samples. Near single-shot sensitivity of DeltaOD <1 x 10(-3) has been achieved, with a response time of <20 ns. Using two continuous-wave EC-QCLs, the current apparatus covers a probe region from 1890-2084 cm(-1), and TRIR spectra are acquired on a point-by-point basis by recording transient absorption decay traces at specific IR wavelengths and combining these to generate spectral time slices. The utility of the apparatus has been demonstrated by monitoring the formation and decay of the one-electron reduced form of the CO(2) reduction catalyst, (Re(I)(bpy)(CO)(3)(CH(3)CN))(+), in acetonitrile with nanosecond time resolution following pulse radiolysis. Characteristic red-shifting of the nu(CO) IR bands confirmed that one-electron reduction of the complex took place. The availability of

  10. Remote sensing of atmospheric trace gases by diode laser spectroscopy

    Science.gov (United States)

    Liu, Jianguo; Kan, Ruifeng; He, Yabai; He, Ying; Zhang, Yujun; Xie, Pinhua; liu, Wenqing

    2016-04-01

    Gaseous ammonia is the most abundant alkaline trace gas in the atmosphere. In order to study its role in acid deposition and aerosol formation, as well as its influence on the regional air quality and atmospheric visibility, several instruments has been developed based on TDLAS (Tunable Diode Laser Absorption Spectroscopy) techniques. In this paper, a long open path TDLAS system and a continuous-wave CRDS (Cavity-Ring down Spectroscopy) system are presented. The long open path system has been developed for NH3 in-situ monitoring by combining wavelength modulation with harmonic detection techniques to obtain the necessary detection sensitivity. The prototype instrument has been used to monitor atmospheric NH3 concentration at an urban site near Beijing National Stadium during Beijing Olympics in 2008, and recently used to measure the fluxes of NH3 from farm fields by flux-gradient method. The detection limit for ammonia is proved approximately 3ppb for a total path length of 456m. The continuous-wave, rapidly swept CRDS system has been developed for localized atmospheric sensing of trace gases at remote sites. Passive open-path optical sensor units could be coupled by optical fiber over distances of >1 km to a single transmitter/receiver console incorporating a photodetector and a swept-frequency diode laser tuned to molecule-specific near-infrared wavelengths. A noise-limited minimum detectable mixing ratio of ~11 ppbv is attained for ammonia at atmospheric pressure. The developed instruments are deployable in agricultural, industrial, and natural atmospheric environments.

  11. Nanostructural features degrading the performance of superconducting radio frequency niobium cavities revealed by transmission electron microscopy and electron energy loss spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Trenikhina, Y., E-mail: yuliatr@fnal.gov [Physics Department, Illinois Institute of Technology, Chicago, Illinois 60616 (United States); Fermi National Accelerator Laboratory, Batavia, Illinois 60510 (United States); Romanenko, A., E-mail: aroman@fnal.gov [Fermi National Accelerator Laboratory, Batavia, Illinois 60510 (United States); Kwon, J.; Zuo, J.-M. [Materials Science and Engineering Department, University of Illinois, Urbana, Illinois 61801 (United States); Zasadzinski, J. F. [Physics Department, Illinois Institute of Technology, Chicago, Illinois 60616 (United States)

    2015-04-21

    Nanoscale defect structure within the magnetic penetration depth of ∼100 nm is key to the performance limitations of niobium superconducting radio frequency cavities. Using a unique combination of advanced thermometry during cavity RF measurements, and TEM structural and compositional characterization of the samples extracted from cavity walls, we discover the existence of nanoscale hydrides in electropolished cavities limited by the high field Q slope, and show the decreased hydride formation in the electropolished cavity after 120 °C baking. Furthermore, we demonstrate that adding 800 °C hydrogen degassing followed by light buffered chemical polishing restores the hydride formation to the pre-120 °C bake level. We also show absence of niobium oxides along the grain boundaries and the modifications of the surface oxide upon 120 °C bake.

  12. Nanostructural features degrading the performance of superconducting radio frequency niobium cavities revealed by transmission electron microscopy and electron energy loss spectroscopy

    International Nuclear Information System (INIS)

    Nanoscale defect structure within the magnetic penetration depth of ∼100 nm is key to the performance limitations of niobium superconducting radio frequency cavities. Using a unique combination of advanced thermometry during cavity RF measurements, and TEM structural and compositional characterization of the samples extracted from cavity walls, we discover the existence of nanoscale hydrides in electropolished cavities limited by the high field Q slope, and show the decreased hydride formation in the electropolished cavity after 120 °C baking. Furthermore, we demonstrate that adding 800 °C hydrogen degassing followed by light buffered chemical polishing restores the hydride formation to the pre-120 °C bake level. We also show absence of niobium oxides along the grain boundaries and the modifications of the surface oxide upon 120 °C bake

  13. Nanostructural features degrading the performance of superconducting radio frequency niobium cavities revealed by transmission electron microscopy and electron energy loss spectroscopy

    International Nuclear Information System (INIS)

    Nanoscale defect structure within the magnetic penetration depth of ~100 nm is key to the performance limitations of niobium superconducting radio frequency cavities. Using a unique combination of advanced thermometry during cavity RF measurements, and TEM structural and compositional characterization of the samples extracted from cavity walls, we discover the existence of nanoscale hydrides in electropolished cavities limited by the high field Q slope, and show the decreased hydride formation in the electropolished cavity after 120°C baking. Furthermore, we demonstrate that adding 800°C hydrogen degassing followed by light buffered chemical polishing restores the hydride formation to the pre-120°C bake level. We also show absence of niobium oxides along the grain boundaries and the modifications of the surface oxide upon 120°C bake

  14. In Situ Stable Isotopic Detection of Anaerobic Oxidation of Methane in Monterey Bay Cold Seeps Via Off-Axis Integrated Cavity Output Spectroscopy

    Science.gov (United States)

    Wankel, S. D.; Gupta, M.; Leen, J.; Provencal, R. A.; Parsotam, V.; Girguis, P. R.

    2010-12-01

    Anaerobic methane oxidation (AOM) plays an important role in global climate change by governing the release of methane from anoxic sediments into the global ocean and ultimately the atmosphere. Thus, gaining an accurate understanding of both the distribution of methane sources and the occurrence of AOM as well as the spatial and temporal variability of cycling pathways is critical. Environmental analyses of methane stable isotopic composition (δ13C-CH4) provide just such an indicator of methane source, whether biogenic or thermogenic, as well as a spatial and temporal integrator of microbial cycling pathways, such as AOM. Here we present results from several deployments of a newly developed in situ methane stable isotope analyzer capable of measuring δ13C-CH4 to full ocean depths. The instrument consisted of a miniaturized Off-Axis Integrated Cavity Output Spectroscopy (Off-Axis ICOS) analyzer housed in a cylindrical titanium pressure vessel for deep sea deployment. Dissolved gas was extracted from seawater using a Teflon AF diffusion membrane inlet. The instrument had an operating wavelength of 1647 nm and used chemometric spectral decomposition to determine the relative concentrations of 13CH4 and 12CH4 with a sensitivity of ± 0.2‰. Deployments to cold seep environments revealed a distinct separation in carbon isotopic composition between methane in advecting fluids as compared with methane from sediment pore fluids. During multiple visits to two different sites at Extrovert Cliff in Monterey Bay (960m), methane in advecting fluids ranged from -70.2‰ to -63.8‰. In contrast, methane-rich fluids sampled directly from pushcore holes taken through seep sediments contained methane with substantially higher δ13C values ranging from -64.2‰ to -50.2‰. These data implicate the influence of anaerobic oxidation of methane within these seep sediments. While the advective flux of methane to the seafloor from the central orifice of the seep is substantial, using

  15. Ozone spectroscopy in the electronic ground state: High-resolution spectra analyses and update of line parameters since 2003

    International Nuclear Information System (INIS)

    The state of the art analyses of high-resolution ozone spectra and a critical discussion of line parameters updated since the previous review by Rinsland et al. [J Quant Spectrosc Radiat Transfer 2003;82:207–18] are presented. We focus on recent works revisiting improved measurements and analyses of Fourier transform spectra below 5600 cm−1 and review Cavity Ring-Down Spectroscopy measurements and analyses in the 5850–7920 cm−1 spectral region which have been performed for 16O3 and all 18O enriched ozone isotopologues. Various issues related to resonance perturbations due to dark states are discussed as well as the issues concerning the accuracy of the experimental parameters, the data modelling and the data reduction. Comparisons of vibration levels determined from spectra analyses with predictions from the molecular potential functions are given. The procedures of empirical corrections for calculated line lists are described and the “intricate” question of absolute intensity determination is overviewed. Also, a review of deficiencies, challenge for improvements, and related works in progress are reported. -- Highlights: • Recent analyses of ozone spectra include comparison of calculations and observations. • The analyses also include critical discussion of updated line parameters. • They also include related issues for accuracy, dark states and assignments. • They also include newly derived band centres versus theoretical predictions

  16. Simultaneous 13C/12C and (18)O/(16)O isotope ratio measurements on CO2 based on off-axis integrated cavity output spectroscopy.

    Science.gov (United States)

    Jost, Hans-Jürg; Castrillo, Antonio; Wilson, H William

    2006-03-01

    A prototype off-axis integrated cavity output spectrometer (OA-ICOS) utilizing two identical cavities together with a near-infrared (1.63 microm) external cavity tunable diode laser is described. The two-cavity design-one for a reference gas and one for a sample gas-takes advantage of classical double-beam infrared spectrometer characteristics in reducing uncertainties due to laser scan or power instabilities and major temperature variations by a factor of three or better compared with a single-cavity scheme. This is the first OA-ICOS instrument designed to determine 13C/12C and (18)O/(16)O ratios from CO2 rotation/vibration fine structure in three different combination bands. Preliminary results indicate that at 0.8 Hz a precision of 3.3 and 2.8 per thousand is obtained for delta13C and delta(18)O, respectively, over a period of 10 h and a pure CO2 gas sample at 26 hPa. By averaging 100 spectra over a subset of the data, we achieved a precision of 1.6 and 0.8 \\permil\\ for delta13C and delta(18)O, respectively. PMID:16500753

  17. Dental cavities

    Science.gov (United States)

    ... leading to cavities. Treatment may involve: Fillings Crowns Root canals Dentists fill teeth by removing the decayed tooth ... gold, porcelain, or porcelain attached to metal. A root canal is recommended if the nerve in a tooth ...

  18. radiofrequency cavity

    CERN Multimedia

    1988-01-01

    The pulse of a particle accelerator. 128 of these radio frequency cavities were positioned around CERN's 27-kilometre LEP ring to accelerate electrons and positrons. The acceleration was produced by microwave electric oscillations at 352 MHz. The electrons and positrons were grouped into bunches, like beads on a string, and the copper sphere at the top stored the microwave energy between the passage of individual bunches. This made for valuable energy savings as it reduced the heat generated in the cavity.

  19. Simultaneous measurements of OH(A) and OH(X) radicals in microwave plasma jet-assisted combustion of methane/air mixtures around the lean-burn limit using optical emission spectroscopy and cavity ringdown spectroscopy

    International Nuclear Information System (INIS)

    We report a new plasma-assisted combustion system, in which a continuous atmospheric argon microwave plasma jet is employed to enhance combustion of methane/air mixtures in different fuel equivalence ratios (φ) ranging from 0.35 to 1.5. The combustor has three distinct reaction zones along the jet axis (the combustion flame direction): the pure plasma zone, the hybrid plasma-flame zone and the combustion flame zone. Each of the three zones is clearly defined by its emission spectral fingerprints. The plasma zone was featured by strong emissions from OH and NH electronic bands and atomic lines of Ar, Hα and Hβ. In the hybrid zone where the plasma jet met fuel mixtures, emission spectra were dominated by OH, NH and CN transitions and by weak or no atomic transitions. In the combustion flame zone, only weak OH emissions were observed. Simulations of optical emission spectroscopy (OES) yielded gas kinetic temperatures to be 1175 ± 50 K, 1450 ± 50 K and 1865 ± 50 K in each of the three zones, respectively. The plasma-enhancement effect was investigated by comparing the lean-burn limits of the combustion with and without plasma. At the same fuel mixture flow rate of 1.0 standard litre per minute and plasma power of 100 W, the lean-burn limit in terms of the fuel equivalence ratio φ was extended from 0.72 without assistance of the plasma to 0.35 with assistance of the plasma. In addition to OES that was employed to characterize the excited state species including OH(A) in the three different zones, pulsed cavity ringdown spectroscopy was utilized to measure absolute number densities of the ground state OH(X) using the OH A–X (0–0) R2 (1) line in different locations in the flame zone at φ = 0.51, 0.87, 1.10 and 1.45. For rich and lean combustions, significantly different OH(X) number densities and density profiles in the flame zone were observed. At φ = 0.51, the OH(X, V″ = 0, J″ = 0.5) number density increased from 2.29 × 1015

  20. Simultaneous measurements of OH(A) and OH(X) radicals in microwave plasma jet-assisted combustion of methane/air mixtures around the lean-burn limit using optical emission spectroscopy and cavity ringdown spectroscopy

    Science.gov (United States)

    Wang, Chuji; Wu, Wei

    2013-11-01

    We report a new plasma-assisted combustion system, in which a continuous atmospheric argon microwave plasma jet is employed to enhance combustion of methane/air mixtures in different fuel equivalence ratios (φ) ranging from 0.35 to 1.5. The combustor has three distinct reaction zones along the jet axis (the combustion flame direction): the pure plasma zone, the hybrid plasma-flame zone and the combustion flame zone. Each of the three zones is clearly defined by its emission spectral fingerprints. The plasma zone was featured by strong emissions from OH and NH electronic bands and atomic lines of Ar, Hα and Hβ. In the hybrid zone where the plasma jet met fuel mixtures, emission spectra were dominated by OH, NH and CN transitions and by weak or no atomic transitions. In the combustion flame zone, only weak OH emissions were observed. Simulations of optical emission spectroscopy (OES) yielded gas kinetic temperatures to be 1175 ± 50 K, 1450 ± 50 K and 1865 ± 50 K in each of the three zones, respectively. The plasma-enhancement effect was investigated by comparing the lean-burn limits of the combustion with and without plasma. At the same fuel mixture flow rate of 1.0 standard litre per minute and plasma power of 100 W, the lean-burn limit in terms of the fuel equivalence ratio φ was extended from 0.72 without assistance of the plasma to 0.35 with assistance of the plasma. In addition to OES that was employed to characterize the excited state species including OH(A) in the three different zones, pulsed cavity ringdown spectroscopy was utilized to measure absolute number densities of the ground state OH(X) using the OH A-X (0-0) R2 (1) line in different locations in the flame zone at φ = 0.51, 0.87, 1.10 and 1.45. For rich and lean combustions, significantly different OH(X) number densities and density profiles in the flame zone were observed. At φ = 0.51, the OH(X, V″ = 0, J″ = 0.5) number density increased from 2.29 × 1015 molecule cm-3 at the combustor

  1. High resolution spectroscopy of silane with an external-cavity quantum cascade laser: Absolute line strengths of the ν3 fundamental band at 4.6μm

    International Nuclear Information System (INIS)

    The introduction of room temperature continuous wave external-cavity quantum cascade lasers (EC-QCLs) with narrow linewidths has greatly facilitated high resolution spectroscopy over wide spectral ranges in the mid-infrared (MIR) region. Using the wide tuning range of an EC-QCL we have measured the absolute line strengths of many P-branch transitions of the stretching dyad of the ν3 fundamental band of 28SiH4 between 2096 and 2178 cm−1. Furthermore, the high spectral resolution available has enabled us to resolve and measure representative examples of the tetrahedral splittings associated with each component of the P-branch. The positions of these components are in excellent agreement with spherical top data system (STDS) predictions and theoretical transitions from the TDS spectroscopic database for spherical top molecules. These are the first measurements of these line strengths of 28SiH4 and are an example of the applicability of high-powered, widely tunable EC-QCLs to high resolution spectroscopy. - Highlights: • We measured the line strengths of transitions of the ν3 fundamental of 28SiH4. • We used a cw external-cavity quantum cascade laser with narrow linewidth. • The high resolution available enabled us to resolve the tetrahedral splittings. • We observe excellent agreement with spherical top data system predictions. • Excellent agreement with TDS spectroscopic database for spherical top molecules

  2. Analysis of Reaction Mechanisms in Flames Using Combined - and Lif-Spectroscopy

    Science.gov (United States)

    Brockhinke, Andreas; Nau, Patrick; Köhler, Markus; Kohse-Höinghaus, Katharina

    2009-06-01

    Laser-based non-intrusive diagnostic techniques are firmly established as the most versatile tools to study high-temperature gas-phase reactions in general and combustion processes in particular. While fossil fuels remain the most important primary energy carriers, alternative fuels gain in importance. Usually, these fuels contain significant amounts of oxygen, nitrogen and sulphur, leading to different reaction pathways than in the established combustion of hydrocarbons. In order to minimize the formation of pollutants and hazardous compounds (soot, CO, NO_{x}) and increase efficiency, a deeper understanding of these reaction processes is essential. Optical measurements, in particular Cavity Ring-Down Spectroscopy (CRDS) and Laser Induced Fluorescence spectroscopy (LIF), have proven to be well suited for quantitative radical measurements in flames (e.g. OH, ^1CH_2, C_2, HCO). Both techniques provide high sensitivity and selectivity. Our revised experimental setup is designed for quasi-simultaneous measurements, combining the positive features of both complementary techniques. In addition, invasive methods like mass-spectrometry are performed in order to gain a complete understanding of the flame species. In this contribution, we will focus on the quantitative determination of important minor species such as CN, NH_2, CH and formaldehyde in low-pressure flat flames. In addition to investigations of flames with hydrocarbon fuels, we present the first optical measurements in morpholine- and ethylamine-flames. Aim of these measurements is to study the conversion of fuel nitrogen to NO_{x}. Experimental results will be compared with numerical CHEMKIN-II simulations.

  3. Computational Spectroscopy of Polycyclic Aromatic Hydrocarbons In Support of Laboratory Astrophysics

    Science.gov (United States)

    Tan, Xiaofeng; Salama, Farid

    2006-01-01

    Polycyclic aromatic hydrocarbons (PAHs) are strong candidates for the molecular carriers of the unidentified infrared bands (UIR) and the diffuse interstellar bands (DIBs). In order to test the PAH hypothesis, we have systematically measured the vibronic spectra of a number of jet-cooled neutral and ionized PAHs in the near ultraviolet (UV) to visible spectral ranges using the cavity ring-down spectroscopy. To support this experimental effort, we have carried out theoretical studies of the spectra obtained in our measurements. Ab initio and (time-dependent) density.functiona1 theory calculations are performed to obtain the geometries, energetics, vibrational frequencies, transition dipole moments, and normal coordinates of these PAH molecules. Franck-Condon (FC) calculations and/or vibronic calculations are then performed using the calculated normal coordinates and vibrational frequencies to simulate the vibronic spectra. It is found that vibronic interactions in these conjugated pi electron systems are often strong enough to cause significant deviations from the Born-Oppenheimer (BO) approximation. For vibronic transitions that are well described by the BO approximation, the vibronic band profiles are simulated by calculating the rotational structure of the vibronic transitions. Vibronic oscillator strength factors are calculated in the frame of the FC approximation from the electronic transition dipole moments and the FC factors. This computational effort together with our experimental measurements provides, for the first time, powerful tools for comparison with space-based data and, hence, a powerful approach to understand the spectroscopy of interstellar PAH analogs and the nature of the UIR and DIBs.

  4. accelerating cavity

    CERN Multimedia

    On the inside of the cavitytThere is a layer of niobium. Operating at 4.2 degrees above absolute zero, the niobium is superconducting and carries an accelerating field of 6 million volts per metre with negligible losses. Each cavity has a surface of 6 m2. The niobium layer is only 1.2 microns thick, ten times thinner than a hair. Such a large area had never been coated to such a high accuracy. A speck of dust could ruin the performance of the whole cavity so the work had to be done in an extremely clean environment.

  5. Development of a cavity enhanced aerosol albedometer

    OpenAIRE

    Zhao, W.; Xu, X.; Dong, M.; Chen, W.; X. Gu; Hu, C; Huang, Y.; Gao, X; Huang, W.; Zhang, W

    2014-01-01

    We report on the development of a cavity enhanced aerosol single scattering albedometer incorporating incoherent broad-band cavity-enhanced spectroscopy (IBBCEAS) approach and an integrating sphere (IS) for simultaneous in situ measurements of aerosol scattering and extinction coefficients in the exact same sample volume. The cavity enhanced albedometer employed a blue light-emitting diode (LED) based IBBCEAS approach for the measurement of wavelength-resolv...

  6. Ultrasensitive detection of nitric oxide at 5.33 μm by using external cavity quantum cascade laser-based Faraday rotation spectroscopy

    Science.gov (United States)

    Lewicki, Rafał; Doty, James H.; Curl, Robert F.; Tittel, Frank K.; Wysocki, Gerard

    2009-01-01

    A transportable prototype Faraday rotation spectroscopic system based on a tunable external cavity quantum cascade laser has been developed for ultrasensitive detection of nitric oxide (NO). A broadly tunable laser source allows targeting the optimum Q3/2(3/2) molecular transition at 1875.81 cm−1 of the NO fundamental band. For an active optical path of 44 cm and 1-s lock-in time constant minimum NO detection limits (1σ) of 4.3 parts per billion by volume (ppbv) and 0.38 ppbv are obtained by using a thermoelectrically cooled mercury–cadmium–telluride photodetector and liquid nitrogen-cooled indium–antimonide photodetector, respectively. Laboratory performance evaluation and results of continuous, unattended monitoring of atmospheric NO concentration levels are reported. PMID:19625625

  7. Protein dynamics: hydration and cavities

    Directory of Open Access Journals (Sweden)

    K. Heremans

    2005-08-01

    Full Text Available The temperature-pressure behavior of proteins seems to be unique among the biological macromolecules. Thermodynamic as well as kinetic data show the typical elliptical stability diagram. This may be extended by assuming that the unfolded state gives rise to volume and enthalpy-driven liquid-liquid transitions. A molecular interpretation follows from the temperature and the pressure dependence of the hydration and cavities. We suggest that positron annihilation spectroscopy can provide additional quantitative evidence for the contributions of cavities to the dynamics of proteins. Only mature amyloid fibrils that form from unfolded proteins are very resistant to pressure treatment.

  8. Cavity magnomechanics

    Science.gov (United States)

    Zou, Chang-Ling; Zhang, Xufeng; Jiang, Liang; Tang, Hong

    2016-05-01

    Recently, cavity magnonics has attracted much attention for potential applications of coherent information transduction and hybrid quantum devices. The magnon is a collective spin wave excitation in ferromagnetic material. It is magnetically tunability, with long coherence time and non-reciprocical interaction with electro-magnetic fields. We report the coherent coupling between magnon, microwave photon and phonon. First, we demonstrate strong coupling and ultrastrong coupling between the magnon in YIG sphere and microwave photon in three-dimensional cavity. Then, based on the hybridized magnon-photon modes, we observe the triply resonant magnon-mcirowave photon-phonon coupling, where the ultrahigh-Q mechanical vibration of YIG sphere is dispersively coupled with the magnon via magnetostrictive interaction. We observe interesting phenomena, including electromagnetically induced transparency/absorption and parametric amplification. In particular, benefit from the large tunability of the magnon, we demonstrate a tunable microwave amplifier with gain as high as 30 dB. The single crystal YIG also has excellent optical properties, and thus provide a unique platform bridging MHz, GHz and THz information carriers. Finally, we present the latest progress towards coherent magnon to optical photon conversion.

  9. Lowest triplet (n,π{sup *}) state of 2-cyclohexen-1-one: Characterization by cavity ringdown spectroscopy and quantum-chemical calculations

    Energy Technology Data Exchange (ETDEWEB)

    McAnally, Michael O.; Zabronsky, Katherine L.; Stupca, Daniel J.; Phillipson, Kaitlyn; Pillsbury, Nathan R.; Drucker, Stephen, E-mail: druckers@uwec.edu [Department of Chemistry, University of Wisconsin-Eau Claire, Eau Claire, Wisconsin 54702-4004 (United States)

    2013-12-07

    The cavity ringdown (CRD) absorption spectrum of 2-cyclohexen-1-one (2CHO) was recorded over the range 401.5–410.5 nm in a room-temperature gas cell. The very weak band system (ε ⩽ 0.1 M{sup −1} cm{sup −1}) in this spectral region is due to the T{sub 1}(n, π*) ← S{sub 0} electronic transition. The 0{sub 0}{sup 0} origin band was assigned to the feature observed at 24 558.8 ± 0.3 cm{sup −1}. We have assigned 46 vibronic transitions in a region extending from −200 to +350 cm{sup −1} relative to the origin band. For the majority of these transitions, we have made corresponding assignments in the spectrum of the deuterated derivative 2CHO-2,6,6-d{sub 3}. From the assignments, we determined fundamental frequencies for several vibrational modes in the T{sub 1}(n, π{sup *}) excited state of 2CHO, including the lowest ring-twisting (99.6 cm{sup −1}) and ring-bending (262.2 cm{sup −1}) modes. These values compare to fundamentals of 122.2 cm{sup −1} and 251.9 cm{sup −1}, respectively, determined previously for the isoconfigurational S{sub 1}(n, π{sup *}) excited state of 2CHO and 99 cm{sup −1} and 248 cm{sup −1}, respectively, for the S{sub 0} ground state. With the aid of quantum-mechanical calculations, we have also ascertained descriptions for these two modes, thereby resolving ambiguities appearing in the previous literature. The ring-twisting mode (ν{sub 39}) contains a significant contribution from O=C–C=C torsion, whereas the ring-bending mode (ν{sub 38} in the ground state) involves mainly the motion of C-5 with respect to the plane containing the other heavy atoms. The CRD spectroscopic data for the T{sub 1}(n, π{sup *}) state have allowed us to benchmark several computational methods for treating excited states, including time-dependent density functional theory and an equation-of-motion coupled cluster method. In turn, the computational results provide an explanation for observed differences in the T{sub 1}(n,

  10. Lowest triplet (n, π*) electronic state of acrolein: Determination of structural parameters by cavity ringdown spectroscopy and quantum-chemical methods

    Science.gov (United States)

    Hlavacek, Nikolaus C.; McAnally, Michael O.; Drucker, Stephen

    2013-02-01

    The cavity ringdown absorption spectrum of acrolein (propenal, CH2=CH—CH=O) was recorded near 412 nm, under bulk-gas conditions at room temperature and in a free-jet expansion. The measured spectral region includes the 0^0_0 band of the T1(n, π*) ← S0 system. We analyzed the 0^0_0 rotational contour by using the STROTA computer program [R. H. Judge et al., J. Chem. Phys. 103, 5343 (1995)], 10.1063/1.470569, which incorporates an asymmetric rotor Hamiltonian for simulating and fitting singlet-triplet spectra. We used the program to fit T1(n, π*) inertial constants to the room-temperature contour. The determined values (cm-1), with 2σ confidence intervals, are A = 1.662 ± 0.003, B = 0.1485 ± 0.0006, C = 0.1363 ± 0.0004. Linewidth analysis of the jet-cooled spectrum yielded a value of 14 ± 2 ps for the lifetime of isolated acrolein molecules in the T1(n, π*), v = 0 state. We discuss the observed lifetime in the context of previous computational work on acrolein photochemistry. The spectroscopically derived inertial constants for the T1(n, π*) state were used to benchmark a variety of computational methods. One focus was on complete active space methods, such as complete active space self-consistent field (CASSCF) and second-order perturbation theory with a CASSCF reference function (CASPT2), which are applicable to excited states. We also examined the equation-of-motion coupled-cluster and time-dependent density function theory excited-state methods, and finally unrestricted ground-state techniques, including unrestricted density functional theory and unrestricted coupled-cluster theory with single and double and perturbative triple excitations. For each of the above methods, we or others [O. S. Bokareva et al., Int. J. Quantum Chem. 108, 2719 (2008)], 10.1002/qua.21803 used a triple zeta-quality basis set to optimize the T1(n, π*) geometry of acrolein. We find that the multiconfigurational methods provide the best agreement with fitted inertial

  11. Cavity magnomechanics

    Science.gov (United States)

    Zhang, Xufeng; Zou, Changling; Jiang, Liang; Tang, Hong X.

    Mechanical oscillators have been recently widely utilized to couple with optical and microwave photons in a variety of hybrid quantum systems, but they all lack the tunability. The magnetostrictive force provides an alternative mechanism to allow phonon to couple with a different type of information carrier-magnon, the collective excitation of magnetization whose frequency can be tuned by a bias magnetic field. Here, we demonstrate an intriguing hybrid system that consists of a magnonic, a mechanical, and a microwave resonator. The magnon-phonon interaction results in hallmark coherent phenomena such as magnomechanically induced transparency/absorption and magnomechanical parametric amplification. The magnetic field dependence of magnon provides our system with unprecedented tunability. Moreover, the great flexibility of our system allows us to achieve triple resonance among magnon, phonon and photon, which drastically enhances the magnomechanical interaction. Our work demonstrates the fundamental principle of cavity magnetomechanics, opening up great opportunities in various applications, such as tunable microwave filter and amplifier, long-lifetime quantum memories, microwave-to-optics conversion.

  12. Analysis of the hydrogen and oxygen stable isotope ratios of beverage waters without prior water extraction using isotope ratio infrared spectroscopy.

    Science.gov (United States)

    Chesson, Lesley A; Bowen, Gabriel J; Ehleringer, James R

    2010-11-15

    Hydrogen (δ(2)H) and oxygen (δ(18)O) stable isotope analysis is useful when tracing the origin of water in beverages, but traditional analytical techniques are limited to pure or extracted waters. We measured the isotopic composition of extracted beverage water using both isotope ratio infrared spectroscopy (IRIS; specifically, wavelength-scanned cavity ring-down spectroscopy) and isotope ratio mass spectrometry (IRMS). We also analyzed beer, sodas, juices, and milk 'as is' using IRIS. For IRIS analysis, four sequential injections of each sample were measured and data were corrected for sample-to-sample memory using injections (a) 1-4, (b) 2-4, and (c) 3-4. The variation between δ(2)H and δ(18)O values calculated using the three correction methods was larger for unextracted (i.e., complex) beverages than for waters. The memory correction was smallest when using injections 3-4. Beverage water δ(2)H and δ(18)O values generally fit the Global Meteoric Water Line, with the exception of water from fruit juices. The beverage water stable isotope ratios measured using IRIS agreed well with the IRMS data and fit 1:1 lines, with the exception of sodas and juices (δ(2)H values) and beers (δ(18)O values). The δ(2)H and δ(18)O values of waters extracted from beer, soda, juice, and milk were correlated with complex beverage δ(2)H and δ(18)O values (r = 0.998 and 0.997, respectively) and generally fit 1:1 lines. We conclude that it is possible to analyze complex beverages, without water extraction, using IRIS although caution is needed when analyzing beverages containing sugars, which can clog the syringe and increase memory, or alcohol, a known spectral interference. PMID:20941769

  13. A new method for continuous measurements of oceanic and atmospheric N2O, CO and CO2: performance of off-axis integrated cavity output spectroscopy (OA-ICOS coupled to non-dispersive infrared detection (NDIR

    Directory of Open Access Journals (Sweden)

    D. L. Arévalo-Martínez

    2013-07-01

    Full Text Available A new system for continuous, highly-resolved oceanic and atmospheric measurements of N2O, CO and CO2 is described. The system is based upon off-axis integrated cavity output spectroscopy (OA-ICOS and a non-dispersive infrared analyzer (NDIR both coupled to a Weiss-type equilibrator. Performance of the combined setup was evaluated by testing its precision, accuracy, long-term stability, linearity and response time. Furthermore, the setup was tested during two oceanographic campaigns in the equatorial Atlantic Ocean in order to explore its potential for autonomous deployment onboard voluntary observing ships (VOS. Improved equilibrator response times for N2O (2.5 min and CO (45 min were achieved in comparison to response times from similar chamber designs used by previous studies. High stability of the OA-ICOS analyzer was demonstrated by low optimal integration times of 2 and 4 min for N2O and CO respectively, as well as detection limits of −1/2. Results from a direct comparison of the method presented here and well-established discrete methods for oceanic N2O and CO2 measurements showed very good consistency. The favorable agreement between underway atmospheric N2O, CO and CO2 measurements and monthly means at Ascension Island (7.96° S 14.4° W further suggests a reliable operation of the underway setup in the field. The potential of the system as an improved platform for measurements of trace gases was explored by using continuous N2O and CO2 data to characterize the development of the seasonal equatorial upwelling in the Atlantic Ocean during two R/V Maria S. Merian cruises. A similar record of high-resolution CO measurements was simultaneously obtained offering for the first time the possibility of a comprehensive view on the distribution and emissions of these climate relevant gases on the area. The relatively simple underway N2O/CO/CO2 setup is suitable for long-term deployment on board of research and commercial vessels although

  14. Crab Cavity Development

    CERN Document Server

    Calaga, R; Burt, G; Ratti, A

    2015-01-01

    The HL-LHC upgrade will use deflecting (or crab) cavities to compensate for geometric luminosity loss at low β* and non-zero crossing angle. A local scheme with crab cavity pairs across the IPs is used employing compact crab cavities at 400 MHz. Design of the cavities, the cryomodules and the RF system is well advanced. The LHC crab cavities will be validated initially with proton beam in the SPS.

  15. High accuracy laboratory spectroscopy to support active greenhouse gas sensing

    Science.gov (United States)

    Long, D. A.; Bielska, K.; Cygan, A.; Havey, D. K.; Okumura, M.; Miller, C. E.; Lisak, D.; Hodges, J. T.

    2011-12-01

    Recent carbon dioxide (CO2) remote sensing missions have set precision targets as demanding as 0.25% (1 ppm) in order to elucidate carbon sources and sinks [1]. These ambitious measurement targets will require the most precise body of spectroscopic reference data ever assembled. Active sensing missions will be especially susceptible to subtle line shape effects as the narrow bandwidth of these measurements will greatly limit the number of spectral transitions which are employed in retrievals. In order to assist these remote sensing missions we have employed frequency-stabilized cavity ring-down spectroscopy (FS-CRDS) [2], a high-resolution, ultrasensitive laboratory technique, to measure precise line shape parameters for transitions of O2, CO2, and other atmospherically-relevant species within the near-infrared. These measurements have led to new HITRAN-style line lists for both 16O2 [3] and rare isotopologue [4] transitions in the A-band. In addition, we have performed detailed line shape studies of CO2 transitions near 1.6 μm under a variety of broadening conditions [5]. We will address recent measurements in these bands as well as highlight recent instrumental improvements to the FS-CRDS spectrometer. These improvements include the use of the Pound-Drever-Hall locking scheme, a high bandwidth servo which enables measurements to be made at rates greater than 10 kHz [6]. In addition, an optical frequency comb will be utilized as a frequency reference, which should allow for transition frequencies to be measured with uncertainties below 10 kHz (3×10-7 cm-1). [1] C. E. Miller, D. Crisp, P. L. DeCola, S. C. Olsen, et al., J. Geophys. Res.-Atmos. 112, D10314 (2007). [2] J. T. Hodges, H. P. Layer, W. W. Miller, G. E. Scace, Rev. Sci. Instrum. 75, 849-863 (2004). [3] D. A. Long, D. K. Havey, M. Okumura, C. E. Miller, et al., J. Quant. Spectrosc. Radiat. Transfer 111, 2021-2036 (2010). [4] D. A. Long, D. K. Havey, S. S. Yu, M. Okumura, et al., J. Quant. Spectrosc

  16. An intra-cavity device with a discharge-drived CW DF chemical laser

    Science.gov (United States)

    Yan, Baozhu; Liu, Wenguang; Zhou, Qiong; Yuan, Shengfu; Lu, Qisheng

    2015-05-01

    The performance parameters of reflecting mirrors such as absorption coefficient or thermal distortion determine the beam quality of the output laser, so the quality of mirrors is one of the most important factors affecting the capability of the whole laser system. At the present time, there was obviously insufficient in test methods for the mirrors performance. The reflection coefficient, absorption coefficient and scattering coefficient of mirrors could be measured by a lot of test methods such as cavity ring-down method, photothermal deflection method, surface thermal lens method and laser calorimetry. But these methods could not test under high power density radiation. So the test data and results could not indicate the real performance in a real laser system exactly. Testing in a real laser system would be expensive and time consuming. Therefore, the test sequence and data would not be sufficient to analyze and realize the performance of mirrors. To examine the performance of mirrors under high power density radiation, the working principle of intra-cavity was introduced in this paper. Utilizing an output mirror with a low output coupling ratio, an intra-cavity could produce high-power density laser in the resonant cavity on the basis of a relatively small scale of gain medium, and the consumption and cost were very low relatively. Based on a discharge-drived CW DF chemical laser, an intra-cavity device was established. A laser beam of 3kw/cm2 was achieved in the resonant cavity. Two pieces of 22.5 degree mirrors and two pieces of 45 degree mirrors could be tested simultaneously. Absorption coefficient and thermal distortion were measured by calorimetry and Hartmann wavefront sensor respectively. This device was simple, convenient, low-maintenance, and could work for a long time. The test results would provide support for process improvement of mirrors.

  17. Superconducting crab cavity

    International Nuclear Information System (INIS)

    Complete overlapping of the electron and positron bunches at colliding point can be attained by using the strong time-depending electromagnetic RF field in the superconducting crab cavity. Commissioning of the crab cavities started in February 2007 at KEKB. Effective head-on collision of electron and positron has been achieved successfully. After introduction of crab crossing and crab cavity, the structure and the fabrication of the KEKB superconducting crab cavity are discussed. (author)

  18. RF Cavity Design

    CERN Document Server

    Jensen, E

    2014-01-01

    After a short overview of a general approach to cavity design, we sketch the derivation of waveguide modes from plane waves and of cavity fields from waveguide modes. The characteristic parameters describing cavities and their performance are defined and explained. An equivalent circuit is introduced and extended to explain beam loading and higher order modes. Finally travelling- and standing-wave multi-gap cavities are introduced using the Brillouin diagram.

  19. New on-line method for water isotope analysis of fluid inclusions in speleothems using laser absorption spectroscopy: Application to stalagmites from Borneo and Switzerland

    Science.gov (United States)

    Affolter, Stéphane; Fleitmann, Dominik; Nele Meckler, Anna; Leuenberger, Markus

    2014-05-01

    Speleothems are recognised as key continental archives for paleoclimate reconstructions. They contain fluid inclusions representing past drip water trapped in the calcite structure. Speleothem can be precisely dated and therefore the oxygen (δ18O) and hydrogen (δD) isotopes of fluid inclusions constitute powerful proxies for paleotemperature or to investigate changes in the moisture source over several interglacial-glacial cycles. To liberate fluid inclusion water and to analyse its isotopic composition, a new online extraction method developed at Bern is used. The principle can be summarised as follows: Prior to crushing, the sample is placed into a copper tube, fixed to the line previously heated to 140° C and flushed with a nitrogen and standard water mixture. Thereafter, the speleothem sample is crushed using a simple hydraulic crushing device and the released water from fluid inclusions is transferred by the nitrogen-standard water mixture flow to a Picarro L1102-i isotopic liquid water and water vapor analyser. The measuring principle is based on wavelength-scanned cavity ring-down spectroscopy (WS-CRDS) technology that allows us to simultaneously monitor hydrogen and oxygen isotopes. Reproducibility of standard water measurements is typically better than 1.5 o for δD and 0.4 o for δ18O. With this method, we successfully analysed δD and δ18O isotopic composition of a stalagmite from Northern Borneo (tropical West Pacific) covering almost two glacial-interglacial cycles from MIS 12 to early MIS 9 (460-330 ka) as well as recent samples from Switzerland and Borneo. These results are used in combination with calcite δ18O to reconstruct paleotemperature. Currently, we are measuring a stalagmite from Milandre cave (Jura, Switzerland) covering the Bølling-Allerød, Younger Dryas cold phase and the Holocene.

  20. Real-time analysis of δ13C- and δD-CH4 in ambient air with laser spectroscopy: method development and first intercomparison results

    Science.gov (United States)

    Eyer, S.; Tuzson, B.; Popa, M. E.; van der Veen, C.; Röckmann, T.; Rothe, M.; Brand, W. A.; Fisher, R.; Lowry, D.; Nisbet, E. G.; Brennwald, M. S.; Harris, E.; Zellweger, C.; Emmenegger, L.; Fischer, H.; Mohn, J.

    2015-08-01

    In situ and simultaneous measurement of the three most abundant isotopologues of methane using mid-infrared laser absorption spectroscopy is demonstrated. A field-deployable, autonomous platform is realized by coupling a compact quantum cascade laser absorption spectrometer (QCLAS) to a preconcentration unit, called TRace gas EXtractor (TREX). This unit enhances CH4 mole fractions by a factor of up to 500 above ambient levels and quantitatively separates interfering trace gases such as N2O and CO2. The analytical precision of the QCLAS isotope measurement on the preconcentrated (750 ppm, parts-per-million, μmole/mole) methane is 0.1 and 0.5 ‰ for δ13C- and δD-CH4 at 10 min averaging time. Based on replicate measurements of compressed air during a two-week intercomparison campaign, the repeatability of the TREX-QCLAS was determined to be 0.19 and 1.9 ‰ for δ13C and δD-CH4, respectively. In this intercomparison campaign the new in situ technique is compared to isotope-ratio mass-spectrometry (IRMS) based on glass flask and bag sampling and real time CH4 isotope analysis by two commercially available laser spectrometers. Both laser-based analyzers were limited to methane mole fraction and δ13C-CH4 analysis, and only one of them, a cavity ring down spectrometer, was capable to deliver meaningful data for the isotopic composition. After correcting for scale offsets, the average difference between TREX-QCLAS data and bag/flask sampling-IRMS values are within the extended WMO compatibility goals of 0.2 and 5 ‰ for δ13C- and δD-CH4, respectively. Thus, the intercomparison also reveals the need for reference air samples with accurately determined isotopic composition of CH4 to further improve the interlaboratory compatibility.

  1. Real-time analysis of δ13C- and δD-CH4 in ambient air with laser spectroscopy: method development and first intercomparison results

    Directory of Open Access Journals (Sweden)

    S. Eyer

    2015-08-01

    Full Text Available In situ and simultaneous measurement of the three most abundant isotopologues of methane using mid-infrared laser absorption spectroscopy is demonstrated. A field-deployable, autonomous platform is realized by coupling a compact quantum cascade laser absorption spectrometer (QCLAS to a preconcentration unit, called TRace gas EXtractor (TREX. This unit enhances CH4 mole fractions by a factor of up to 500 above ambient levels and quantitatively separates interfering trace gases such as N2O and CO2. The analytical precision of the QCLAS isotope measurement on the preconcentrated (750 ppm, parts-per-million, μmole/mole methane is 0.1 and 0.5 ‰ for δ13C- and δD-CH4 at 10 min averaging time. Based on replicate measurements of compressed air during a two-week intercomparison campaign, the repeatability of the TREX-QCLAS was determined to be 0.19 and 1.9 ‰ for δ13C and δD-CH4, respectively. In this intercomparison campaign the new in situ technique is compared to isotope-ratio mass-spectrometry (IRMS based on glass flask and bag sampling and real time CH4 isotope analysis by two commercially available laser spectrometers. Both laser-based analyzers were limited to methane mole fraction and δ13C-CH4 analysis, and only one of them, a cavity ring down spectrometer, was capable to deliver meaningful data for the isotopic composition. After correcting for scale offsets, the average difference between TREX–QCLAS data and bag/flask sampling–IRMS values are within the extended WMO compatibility goals of 0.2 and 5 ‰ for δ13C- and δD-CH4, respectively. Thus, the intercomparison also reveals the need for reference air samples with accurately determined isotopic composition of CH4 to further improve the interlaboratory compatibility.

  2. Ion-cavity system for quantum networks

    International Nuclear Information System (INIS)

    Full text: A single atom interacting with a single mode of a cavity allows us to probe the quantum interaction between light and matter. In the context of quantum networks, such a system can provide an interface between stationary and flying qubits, making it possible for single photons to transport quantum information between the network nodes. We study a single 40Ca+ ion trapped inside a high-finesse optical resonator. First, we demonstrate and characterize a single-photon source, in which a vacuum-stimulated Raman process transfers atomic population between two Zeeman states of the ion, creating a single photon in the cavity. We evaluate the photon statistics by measuring the second-order correlation function. Moreover, we obtain the photon temporal profile and investigate the dynamics of the process. Secondly, we perform Raman spectroscopy using the cavity. Residual motion of the ion introduces motional sidebands in the Raman spectrum and thus offers prospects for cavity-assisted cooling. (author)

  3. Photonic crystal cavities with metallic Schottky contacts

    International Nuclear Information System (INIS)

    We report about the fabrication and analysis of high Q photonic crystal cavities with metallic Schottky-contacts. The structures are based on GaAs n-i membranes with an InGaAs quantum well in the i-region and nanostructured low ohmic metal top-gates. They are designed for photocurrent readout within the cavity and fast electric manipulations. The cavity structures are characterized by photoluminescence and photocurrent spectroscopy under resonant excitation. We find strong cavity resonances in the photocurrent spectra and surprisingly high Q-factors up to 6500. Temperature dependent photocurrent measurements in the region between 4.5 K and 310 K show an exponential enhancement of the photocurrent signal and an external quantum efficiency up to 0.26

  4. Feedback-free optical cavity with self-resonating mechanism

    Science.gov (United States)

    Uesugi, Y.; Hosaka, Y.; Honda, Y.; Kosuge, A.; Sakaue, K.; Omori, T.; Takahashi, T.; Urakawa, J.; Washio, M.

    2016-05-01

    We demonstrated the operation of a high finesse optical cavity without utilizing an active feedback system to stabilize the resonance. The effective finesse, which is a finesse including the overall system performance, of the cavity was measured to be 394 000 ± 10 000, and the laser power stored in the cavity was 2.52 ± 0.13 kW, which is approximately 187 000 times greater than the incident power to the cavity. The stored power was stabilized with a fluctuation of 1.7%, and we confirmed continuous cavity operation for more than two hours. This result has the potential to trigger an innovative evolution for applications that use optical resonant cavities such as compact photon sources with laser-Compton scattering or cavity enhanced absorption spectroscopy.

  5. Laser spectroscopy

    CERN Document Server

    Demtröder, Wolfgang

    2008-01-01

    Keeping abreast of the latest techniques and applications, this new edition of the standard reference and graduate text on laser spectroscopy has been completely revised and expanded. While the general concept is unchanged, the new edition features a broad array of new material, e.g., frequency doubling in external cavities, reliable cw-parametric oscillators, tunable narrow-band UV sources, more sensitive detection techniques, tunable femtosecond and sub-femtosecond lasers (X-ray region and the attosecond range), control of atomic and molecular excitations, frequency combs able to synchronize independent femtosecond lasers, coherent matter waves, and still more applications in chemical analysis, medical diagnostics, and engineering.

  6. Beam cavity interaction

    CERN Document Server

    Gamp, A

    2011-01-01

    We begin by giving a description of the rf generator-cavity-beam coupled system in terms of basic quantities. Taking beam loading and cavity detuning into account, expressions for the cavity impedance as seen by the generator and as seen by the beam are derived. Subsequently methods of beam-loading compensation by cavity detuning, rf feedback, and feed-forward are described. Examples of digital rf phase and amplitude control for the special case of superconducting cavities are also given. Finally, a dedicated phase loop for damping synchrotron oscillations is discussed.

  7. Complete Measurement of Stable Isotopes in N2O (δ15N, δ15Nα, δ15Nβ, δ18O, δ17O) Using Off-Axis Integrated Cavity Output Spectroscopy (OA-ICOS)

    Science.gov (United States)

    Leen, J. B.; Gupta, M.

    2014-12-01

    Nitrate contamination in water is a worldwide environmental problem and source apportionment is critical to managing nitrate pollution. Fractionation caused by physical, chemical and biological processes alters the isotope ratios of nitrates (15N/14N, 18O/16O and 17O/16O) and biochemical nitrification and denitrification impart different intramolecular site preference (15N14NO vs. 14N15NO). Additionally, atmospheric nitrate is anomalously enriched in 17O compared to other nitrate sources. The anomaly (Δ17O) is conserved during fractionation processes, providing a tracer of atmospheric nitrate. All of these effects can be used to apportion nitrate in soil. Current technology for measuring nitrate isotopes is complicated and costly - it involves conversion of nitrate to nitrous oxide (N2O), purification, preconcentration and measurement by isotope ratio mass spectrometer (IRMS). Site specific measurements require a custom IRMS. There is a pressing need to make this measurement simpler and more accessible. Los Gatos Research has developed a next generation mid-infrared Off-Axis Integrated Cavity Output Spectroscopy (OA-ICOS) analyzer to quantify all stable isotope ratios of N2O (δ15N, δ15Nα, δ15Nβ, δ18O, δ17O). We present the latest performance data demonstrating the precision and accuracy of the OA-ICOS based measurement. At an N2O concentration of 322 ppb, the analyzer quantifies [N2O], δ15N, δ15Na, δ15Nb, and δ18O with a precision of ±0.05 ppb, ±0.4 ‰, ±0.45 ‰, and ±0.6 ‰, and ±0.8 ‰ respectively (1σ, 100s; 1σ, 1000s for δ18O). Measurements of gas standards demonstrate accuracy better than ±1 ‰ for isotope ratios over a wide dynamic range (200 - 100,000 ppb). The measurement of δ17O requires a higher concentration (1 - 50 ppm), easily obtainable through conversion of nitrates in water. For 10 ppm of N2O, the instrument achieves a δ17O precision of ±0.05 ‰ (1σ, 1000s). This performance is sufficient to quantify atmospheric

  8. Cavity turnover and equilibrium cavity densities in a cottonwood bottomland

    Science.gov (United States)

    Sedgwick, James A.; Knopf, Fritz L.

    1992-01-01

    A fundamental factor regulating the numbers of secondary cavity nesting (SCN) birds is the number of extant cavities available for nesting. The number of available cavities may be thought of as being in an approximate equilibrium maintained by a very rough balance between recruitment and loss of cavities. Based on estimates of cavity recruitment and loss, we ascertained equilibrium cavity densities in a mature plains cottonwood (Populus sargentii) bottomland along the South Platte River in northeastern Colorado. Annual cavity recruitment, derived from density estimates of primary cavity nesting (PCN) birds and cavity excavation rates, was estimated to be 71-86 new cavities excavated/100 ha. Of 180 active cavities of 11 species of cavity-nesting birds found in 1985 and 1986, 83 were no longer usable by 1990, giving an average instantaneous rate of cavity loss of r = -0.230. From these values of cavity recruitment and cavity loss, equilibrium cavity density along the South Platte is 238-289 cavities/100 ha. This range of equilibrium cavity density is only slightly above the minimum of 205 cavities/100 ha required by SCN's and suggests that cavity availability may be limiting SCN densities along the South Platte River. We submit that snag management alone does not adequately address SCN habitat needs, and that cavity management, expressed in terms of cavity turnover and cavity densities, may be more useful.

  9. Light extinction by Secondary Organic Aerosol: an intercomparison of three broadband cavity spectrometers

    Directory of Open Access Journals (Sweden)

    R. M. Varma

    2013-07-01

    Full Text Available Broadband optical cavity spectrometers are maturing as a technology for trace gas detection, but only recently have they been used to retrieve the extinction coefficient of aerosols. Sensitive broadband extinction measurements allow explicit separation of gas and particle phase spectral contributions, as well as continuous spectral measurements of aerosol extinction in favourable cases. In this work, we report an intercomparison study of the aerosol extinction coefficients measured by three such instruments: a broadband cavity ring-down spectrometer (BBCRDS, a cavity-enhanced differential optical absorption spectrometer (CE-DOAS, and an incoherent broadband cavity-enhanced absorption spectrometer (IBBCEAS. Experiments were carried out in the SAPHIR atmospheric simulation chamber as part of the NO3Comp campaign to compare the measurement capabilities of NO3 and N2O5 instrumentation. Aerosol extinction coefficients between 655 and 690 nm are reported for secondary organic aerosols (SOA formed by the NO3 oxidation of β-pinene under dry and humid conditions. Despite different measurement approaches and spectral analysis procedures, the three instruments retrieved aerosol extinction coefficients that were in close agreement. The refractive index of SOA formed from the β-pinene + NO3 reaction was 1.61, and was not measurably affected by the chamber humidity or by aging of the aerosol over several hours. This refractive index is significantly larger than SOA refractive indices observed in other studies of OH and ozone-initiated terpene oxidations, and may be caused by the large proportion of organic nitrates in the particle phase. In an experiment involving ammonium sulphate particles the aerosol extinction coefficients as measured by IBBCEAS were found to be in reasonable agreement with those calculated using Mie theory. The results of the study demonstrate the potential of broadband cavity spectrometers for determining the optical properties of

  10. Electromagnetic SCRF Cavity Tuner

    Energy Technology Data Exchange (ETDEWEB)

    Kashikhin, V.; Borissov, E.; Foster, G.W.; Makulski, A.; Pischalnikov, Y.; Khabiboulline, T.; /Fermilab

    2009-05-01

    A novel prototype of SCRF cavity tuner is being designed and tested at Fermilab. This is a superconducting C-type iron dominated magnet having a 10 mm gap, axial symmetry, and a 1 Tesla field. Inside the gap is mounted a superconducting coil capable of moving {+-} 1 mm and producing a longitudinal force up to {+-} 1.5 kN. The static force applied to the RF cavity flanges provides a long-term cavity geometry tuning to a nominal frequency. The same coil powered by fast AC current pulse delivers mechanical perturbation for fast cavity tuning. This fast mechanical perturbation could be used to compensate a dynamic RF cavity detuning caused by cavity Lorentz forces and microphonics. A special configuration of magnet system was designed and tested.

  11. Superconducting cavity development

    International Nuclear Information System (INIS)

    Design and development work of the superconducting cavities for the Neutron Science Project is being continued since 1995. In the cavity design work, RF and structural analyses were carried out in order to determine the cavity shape and to obtain the RF and structural parameters. In the cavity development work, preparation of the test facility, fabrication and tests of the two single-cell prototype cavities of β=0.5 were performed. Good performance of the cavity was demonstrated in the test; obtained surface peak electric field of 44 MV/m is much higher than the design value of 16 MV/m. Resonant frequency shifts due to the vacuum load and the Lorentz force were also measured in the test. (author)

  12. LEP copper accelerating cavities

    CERN Multimedia

    Laurent Guiraud

    1999-01-01

    These copper cavities were used to generate the radio frequency electric field that was used to accelerate electrons and positrons around the 27-km Large Electron-Positron (LEP) collider at CERN, which ran from 1989 to 2000. The copper cavities were gradually replaced from 1996 with new superconducting cavities allowing the collision energy to rise from 90 GeV to 200 GeV by mid-1999.

  13. Optically measuring interior cavities

    Science.gov (United States)

    Stone, Gary Franklin

    2009-11-03

    A method of measuring the three-dimensional volume or perimeter shape of an interior cavity includes the steps of collecting a first optical slice of data that represents a partial volume or perimeter shape of the interior cavity, collecting additional optical slices of data that represents a partial volume or perimeter shape of the interior cavity, and combining the first optical slice of data and the additional optical slices of data to calculate of the three-dimensional volume or perimeter shape of the interior cavity.

  14. Advanced Spectroscopy Technique for Biomedicine

    Science.gov (United States)

    Zhao, Jianhua; Zeng, Haishan

    This chapter presents an overview of the applications of optical spectroscopy in biomedicine. We focus on the optical design aspects of advanced biomedical spectroscopy systems, Raman spectroscopy system in particular. Detailed components and system integration are provided. As examples, two real-time in vivo Raman spectroscopy systems, one for skin cancer detection and the other for endoscopic lung cancer detection, and an in vivo confocal Raman spectroscopy system for skin assessment are presented. The applications of Raman spectroscopy in cancer diagnosis of the skin, lung, colon, oral cavity, gastrointestinal tract, breast, and cervix are summarized.

  15. SPS accelerating cavity

    CERN Multimedia

    CERN PhotoLab

    1981-01-01

    One of the SPS accelerating cavities (200 MHz, travelling wave structure). The power that is fed into the upstream end of the cavity is extracted at the downstream end and sent into a dump load. See 7603195 for more details, 7411032 for the travelling wave structure, and also 8011289, 8302397.

  16. SPS accelerating cavity

    CERN Multimedia

    1980-01-01

    One of the SPS acceleration cavities (200 MHz, travelling wave structure). On the ceiling one sees the coaxial transmission line which feeds the power from the amplifier, located in a surface building above, to the upstream end of the cavity. See 7603195 for more details, 7411032 for the travelling wave structure, and also 8104138, 8302397.

  17. Superconducting RF cavities

    CERN Document Server

    Bernard, Philippe

    1999-01-01

    It was 20 years ago when the research and development programme for LEP superconducting cavities was initiated. It lasted about 10 years. Today, my aim is not to tell you in great detail about the many innovations made thanks to our research, but I would like to point out some milestones in the development of superconducting cavities where Emilio's influence was particularly important.

  18. Ferrite loaded rf cavity

    International Nuclear Information System (INIS)

    The mechanism of a ferrite-loaded rf cavity is explained from the point of view of its operation. Then, an analysis of the automatic cavity-tuning system is presented using the transfer function; and a systematic analysis of a beam-feedback system using transfer functions is also presented. (author)

  19. Superconducting cavities for LEP

    CERN Multimedia

    1983-01-01

    Above: a 350 MHz superconducting accelerating cavity in niobium of the type envisaged for accelerating electrons and positrons in later phases of LEP. Below: a small 1 GHz cavity used for investigating the surface problems of superconducting niobium. Albert Insomby stays on the right. See Annual Report 1983 p. 51.

  20. Passivated niobium cavities

    Science.gov (United States)

    Myneni, Ganapati Rao; Hjorvarsson, Bjorgvin; Ciovati, Gianluigi

    2006-12-19

    A niobium cavity exhibiting high quality factors at high gradients is provided by treating a niobium cavity through a process comprising: 1) removing surface oxides by plasma etching or a similar process; 2) removing hydrogen or other gases absorbed in the bulk niobium by high temperature treatment of the cavity under ultra high vacuum to achieve hydrogen outgassing; and 3) assuring the long term chemical stability of the niobium cavity by applying a passivating layer of a superconducting material having a superconducting transition temperature higher than niobium thereby reducing losses from electron (cooper pair) scattering in the near surface region of the interior of the niobium cavity. According to a preferred embodiment, the passivating layer comprises niobium nitride (NbN) applied by reactive sputtering.

  1. Cover slip external cavity diode laser

    CERN Document Server

    Carr, Adra V; Waitukaitis, Scott R; Perreault, John D; Lonij, Vincent P A; Cronin, Alexander D

    2007-01-01

    The design of a 671 nm diode laser with a mode-hop-free tuning range of 40 GHz is described. This long tuning range is achieved by simultaneously ramping the external cavity length with the laser injection current. The external cavity consists of a microscope cover slip mounted on piezoelectric actuators. In such a configuration the laser output pointing remains fixed, independent of its frequency. Using a diode with an output power of 5-7 mW, the laser linewidth was found to be smaller than 30 MHz. This cover slip cavity and feedforward laser current control system is simple, economical, robust, and easy to use for spectroscopy, as we demonstrate with lithium vapor and lithium atom beam experiments.

  2. Reducing and correcting for contamination of ecosystem water stable isotopes measured by isotope ratio infrared spectroscopy.

    Science.gov (United States)

    Schmidt, Markus; Maseyk, Kadmiel; Lett, Céline; Biron, Philippe; Richard, Patricia; Bariac, Thierry; Seibt, Ulli

    2012-01-30

    Concern exists about the suitability of laser spectroscopic instruments for the measurement of the (18)O/(16)O and (2)H/(1)H values of liquid samples other than pure water. It is possible to derive erroneous isotope values due to optical interference by certain organic compounds, including some commonly present in ecosystem-derived samples such as leaf or soil waters. Here we investigated the reliability of wavelength-scanned cavity ring-down spectroscopy (CRDS) (18)O/(16)O and (2)H/(1)H measurements from a range of ecosystem-derived waters, through comparison with isotope ratio mass spectrometry (IRMS). We tested the residual of the spectral fit S(r) calculated by the CRDS instrument as a means to quantify the difference between the CRDS and IRMS δ-values. There was very good overall agreement between the CRDS and IRMS values for both isotopes, but differences of up to 2.3‰ (δ(18)O values) and 23‰ (δ(2)H values) were observed in leaf water extracts from Citrus limon and Alnus cordata. The S(r) statistic successfully detected contaminated samples. Treatment of Citrus leaf water with activated charcoal reduced, but did not eliminate, δ(2)H(CRDS) - δ(2)H(IRMS) linearly for the tested range of 0-20% charcoal. The effect of distillation temperature on the degree of contamination was large, particularly for δ(2)H values but variable, resulting in positive, negative or no correlation with distillation temperature. S(r) and δ(CRDS) - δ(IRMS) were highly correlated, in particular for δ(2)H values, across the range of samples that we tested, indicating the potential to use this relationship to correct the δ-values of contaminated plant water extracts. We also examined the sensitivity of the CRDS system to changes in the temperature of its operating environment. We found that temperature changes ≥4 °C for δ(18)O values and ≥10 °C for δ(2)H values resulted in errors larger than the CRDS precision for the respective isotopes and advise the use of such

  3. SPS RF Accelerating Cavity

    CERN Multimedia

    1979-01-01

    This picture shows one of the 2 new cavities installed in 1978-1979. The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also increased: to the first 2 MW plant a second 2 MW plant was added and by end 1979 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412016X, 7412017X, 7411048X

  4. SPS RF Cavity

    CERN Multimedia

    1975-01-01

    The picture shows one of the two initially installed cavities. The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also gradually increased: by end 1980 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412017X, 7411048X, 7505074.

  5. Hydroforming of elliptical cavities

    Science.gov (United States)

    Singer, W.; Singer, X.; Jelezov, I.; Kneisel, P.

    2015-02-01

    Activities of the past several years in developing the technique of forming seamless (weldless) cavity cells by hydroforming are summarized. An overview of the technique developed at DESY for the fabrication of single cells and multicells of the TESLA cavity shape is given and the major rf results are presented. The forming is performed by expanding a seamless tube with internal water pressure while simultaneously swaging it axially. Prior to the expansion the tube is necked at the iris area and at the ends. Tube radii and axial displacements are computer controlled during the forming process in accordance with results of finite element method simulations for necking and expansion using the experimentally obtained strain-stress relationship of tube material. In cooperation with industry different methods of niobium seamless tube production have been explored. The most appropriate and successful method is a combination of spinning or deep drawing with flow forming. Several single-cell niobium cavities of the 1.3 GHz TESLA shape were produced by hydroforming. They reached accelerating gradients Eacc up to 35 MV /m after buffered chemical polishing (BCP) and up to 42 MV /m after electropolishing (EP). More recent work concentrated on fabrication and testing of multicell and nine-cell cavities. Several seamless two- and three-cell units were explored. Accelerating gradients Eacc of 30 - 35 MV /m were measured after BCP and Eacc up to 40 MV /m were reached after EP. Nine-cell niobium cavities combining three three-cell units were completed at the company E. Zanon. These cavities reached accelerating gradients of Eacc=30 - 35 MV /m . One cavity is successfully integrated in an XFEL cryomodule and is used in the operation of the FLASH linear accelerator at DESY. Additionally the fabrication of bimetallic single-cell and multicell NbCu cavities by hydroforming was successfully developed. Several NbCu clad single-cell and double-cell cavities of the TESLA shape have been

  6. SPS RF cavity

    CERN Multimedia

    1974-01-01

    The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. A power of up to 790 kW can be supplied to each giving a total accelerating voltage of about 8 MV. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities.

  7. Long Wave Infrared Cavity Enhanced Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Taubman, Matthew S.; Scott, David C.; Cannon, Bret D.; Myers, Tanya L.; Bonebrake, Christopher A.; Aker, Pam M.; Wojcik, Michael D.; Munley, John T.; Nguyen, Vinh T.; Schultz, John F.

    2004-10-01

    The principal goal of Pacific Northwest National Laboratory's (PNNL's) long wave infrared (LWIR) cavity enhanced sensor (CES) project is to explore ultra-sensitive spectroscopic techniques and apply them to the development of LWIR chemical sensors needed for detecting weapons proliferation. This includes detecting not only the weapons of mass destruction (WMDs) themselves, but also signatures of their production and/or detonation. The LWIR CES project is concerned exclusively with developing point sensors; other portions of PNNL's IR Sensors program address stand off detection. PNNL's LWIR CES research is distinguished from that done by others by the use quantum cascade lasers (QCLs) as the light source. QCLs are novel devices, and a significant fraction of our research has been devoted to developing the procedures and hardware required to implement them most effectively for chemical sensing. This report details the progress we have made on our LWIR CES sensor development. During FY02, PNNL investigated three LWIR CES implementations beginning with the easiest to implement, direct cavity-enhanced detection (simple CES), including a technique of intermediate difficulty, cavity-dithered phase-sensitive detection (FM recovery CES) through to the most complex technique, that of resonant sideband cavity-enhanced detection also known as noise-immune cavity-enhanced optical heterodyne molecular spectroscopy, or NICE-OHMS.

  8. External cavity quantum cascade laser

    International Nuclear Information System (INIS)

    In this paper we review the progress of the development of mid-infrared quantum cascade lasers (QCLs) operated in an external cavity configuration. We concentrate on QCLs based on the bound-to-continuum design, since this design is especially suitable for broadband applications. Since they were first demonstrated, these laser-based tunable sources have improved in performance in terms of output power, duty cycle, operation temperature and tuneability. Nowadays they are an interesting alternative to FTIRs for some applications. They operate at room temperature, feature a high spectral resolution while being small in size. They were successfully used in different absorption spectroscopy techniques. Due to their vast potential for applications in industry, medicine, security and research, these sources enjoy increasing interest within the research community as well as in industry. (topical review)

  9. Cavity Optomechanics at Millikelvin Temperatures

    Science.gov (United States)

    Meenehan, Sean Michael

    mechanical frequency of these systems allows for the possibility of using a dilution refrigerator to simultaneously achieve low thermal occupancy and long mechanical coherence time by passively cooling the device to the millikelvin regime. This thesis describes efforts to realize the measurement of OMC cavities inside a dilution refrigerator, including the development of fridge-compatible optical coupling schemes and the characterization of the heating dynamics of the mechanical resonator at sub-kelvin temperatures. We will begin by summarizing the theoretical framework used to describe cavity optomechanical systems, as well as a handful of the quantum applications envisioned for such devices. Then, we will present background on the design of the nanobeam OMC cavities used for this work, along with details of the design and characterization of tapered fiber couplers for optical coupling inside the fridge. Finally, we will present measurements of the devices at fridge base temperatures of Tf = 10 mK, using both heterodyne spectroscopy and time-resolved sideband photon counting, as well as detailed analysis of the prospects for future quantum applications based on the observed optically-induced heating.

  10. SPS accelerating cavity

    CERN Multimedia

    1983-01-01

    See photo 8202397: View towards the downstream end of one of the SPS accelerating cavities (200 MHz, travelling wave structure). See 7603195 and 8011289 for more details, 7411032 for the travelling wave structure, and also 8104138.

  11. SPS accelerating cavity

    CERN Multimedia

    1983-01-01

    View towards the downstream end of one of the SPS accelerating cavities (200 MHz, travelling wave structure). See 7603195 and 8011289 for more details, 7411032 for the travelling wave structure, and also 8104138.

  12. accelerating cavity from LEP

    CERN Multimedia

    This is an accelerating cavity from LEP, with a layer of niobium on the inside. Operating at 4.2 degrees above absolute zero, the niobium is superconducting and carries an accelerating field of 6 million volts per metre with negligible losses. Each cavity has a surface of 6 m2. The niobium layer is only 1.2 microns thick, ten times thinner than a hair. Such a large area had never been coated to such a high accuracy. A speck of dust could ruin the performance of the whole cavity so the work had to be done in an extremely clean environment. These challenging requirements pushed European industry to new achievements. 256 of these cavities are now used in LEP to double the energy of the particle beams.

  13. Moving Detectors in Cavities

    CERN Document Server

    Obadia, N

    2007-01-01

    We consider two-level detectors, coupled to a quantum scalar field, moving inside cavities. We highlight some pathological resonant effects due to abrupt boundaries, and decide to describe the cavity by switching smoothly the interaction by a time-dependent gate-like function. Considering uniformly accelerated trajectories, we show that some specific choices of non-adiabatic switching have led to hazardous interpretations about the enhancement of the Unruh effect in cavities. More specifically, we show that the emission/absorption ratio takes arbitrary high values according to the emitted quanta properties and to the transients undergone at the entrance and the exit of the cavity, {\\it independently of the acceleration}. An explicit example is provided where we show that inertial and uniformly accelerated world-lines can even lead to the same ``pseudo-temperature''.

  14. SPS accelerating cavity

    CERN Multimedia

    1976-01-01

    The SPS started up with 2 accelerating cavities (each consisting of 5 tank sections) in LSS3. They have a 200 MHz travelling wave structure (see 7411032 and 7802190) and 750 kW of power is fed to each of the cavities from a 1 MW tetrode power amplifier, located in a surface building above, via a coaxial transmission line. Clemens Zettler, builder of the SPS RF system, is standing at the side of one of the cavities. In 1978 and 1979 another 2 cavities were added and entered service in 1980. These were part of the intensity improvement programme and served well for the new role of the SPS as proton-antiproton collider. See also 7411032, 8011289, 8104138, 8302397.

  15. Melatonin and Oral Cavity

    OpenAIRE

    Murat İnanç Cengiz; Seda Cengiz; Hom-Lay Wang

    2012-01-01

    While initially the oral cavity was considered to be mainly a source of various bacteria, their toxins and antigens, recent studies showed that it may also be a location of oxidative stress and periodontal inflammation. Accordingly, this paper focuses on the involvement of melatonin in oxidative stress diseases of oral cavity as well as on potential therapeutic implications of melatonin in dental disorders. Melatonin has immunomodulatory and antioxidant activities, stimulates the proliferatio...

  16. Oral cavity and leprosy

    OpenAIRE

    Shambulingappa Pallagatti; Soheyl Sheikh; Anupreet Kaur; Amit Aggarwal; Ravinder Singh2

    2012-01-01

    Although leprosy involves the oral cavity in up to 60% of the patients, examination of the oral cavity in leprosy clinics or oral health science clinics is often neglected. Oral involvement in leprosy can broadly be divided into non-specific and specific lesions. In this review, we discuss various oral manifestations in leprosy patients so as to increase the awareness about this aspect among dermatologists and dental surgeons.

  17. Hydroforming of Elliptical Cavities

    OpenAIRE

    W. Singer; Singer, X.; Jelezov, I.; Kneisel, P.

    2015-01-01

    Activities of the past several years in developing the technique of forming seamless (weldless) cavity cells by hydroforming are summarized. An overview of the technique developed at DESY for the fabrication of single cells and multicells of the TESLA cavity shape is given and the major rf results are presented. The forming is performed by expanding a seamless tube with internal water pressure while simultaneously swaging it axially. Prior to the expansion the tube is necked at the iris area ...

  18. Hybrid vertical cavity laser

    DEFF Research Database (Denmark)

    Chung, Il-Sug; Mørk, Jesper

    2010-01-01

    A new hybrid vertical cavity laser structure for silicon photonics is suggested and numerically investigated. It incorporates a silicon subwavelength grating as a mirror and a lateral output coupler to a silicon ridge waveguide.......A new hybrid vertical cavity laser structure for silicon photonics is suggested and numerically investigated. It incorporates a silicon subwavelength grating as a mirror and a lateral output coupler to a silicon ridge waveguide....

  19. Cavity-enhanced Raman Microscopy of Individual Carbon Nanotubes

    CERN Document Server

    Hümmer, Thomas; Hofmann, Matthias S; Hänsch, Theodor W; Högele, Alexander; Hunger, David

    2015-01-01

    Raman spectroscopy reveals chemically specific information, and combined with imaging provides label-free insight into the molecular world. However, the signals are intrinsically weak and call for enhancement techniques. Here we use a tunable high-finesse optical microcavity to demonstrate Purcell enhancement of Raman scattering in combination with high-resolution scanning-cavity imaging. We detect cavity-enhanced Raman spectra of individual single-walled carbon nanotubes, expand the technique to hyperspectral imaging, and co-localize measurements with cavity-enhanced absorption microscopy. Direct comparison with confocal Raman microscopy yields a 550-times enhanced collectable Raman scattering spectral density and a 11-fold enhancement of the integrated count rate. The quantitative character, the inherent spectral filtering, and the absence of intrinsic background in cavity-vacuum stimulated Raman scattering renders our technique a promising tool for molecular imaging. Furthermore, cavity-enhanced Raman tran...

  20. Perturbative corrections to photon coincidence spectroscopy

    OpenAIRE

    Horvath, L.; Sanders, B. C.

    2000-01-01

    Photon coincidence spectroscopy is a promising technique for probing the nonlinear regime of cavity quantum electrodynamics in the optical domain, however its accuracy is mitigated by two factors: higher-order photon correlations, which contribute to an enhanced pair count rate, and non-simultaneity of emitted photon pairs from the optical cavity. We show that the technique of photon coincidence spectroscopy is effective in the presence of these effects if the quantitative predictions are adj...

  1. Metasurface external cavity laser

    Science.gov (United States)

    Xu, Luyao; Curwen, Christopher A.; Hon, Philip W. C.; Chen, Qi-Sheng; Itoh, Tatsuo; Williams, Benjamin S.

    2015-11-01

    A vertical-external-cavity surface-emitting-laser is demonstrated in the terahertz range, which is based upon an amplifying metasurface reflector composed of a sub-wavelength array of antenna-coupled quantum-cascade sub-cavities. Lasing is possible when the metasurface reflector is placed into a low-loss external cavity such that the external cavity—not the sub-cavities—determines the beam properties. A near-Gaussian beam of 4.3° × 5.1° divergence is observed and an output power level >5 mW is achieved. The polarized response of the metasurface allows the use of a wire-grid polarizer as an output coupler that is continuously tunable.

  2. Metasurface external cavity laser

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Luyao, E-mail: luyaoxu.ee@ucla.edu; Curwen, Christopher A.; Williams, Benjamin S. [Department of Electrical Engineering, University of California, Los Angeles, California 90095 (United States); California NanoSystems Institute, University of California, Los Angeles, California 90095 (United States); Hon, Philip W. C.; Itoh, Tatsuo [Department of Electrical Engineering, University of California, Los Angeles, California 90095 (United States); Chen, Qi-Sheng [Northrop Grumman Aerospace Systems, Redondo Beach, California 90278 (United States)

    2015-11-30

    A vertical-external-cavity surface-emitting-laser is demonstrated in the terahertz range, which is based upon an amplifying metasurface reflector composed of a sub-wavelength array of antenna-coupled quantum-cascade sub-cavities. Lasing is possible when the metasurface reflector is placed into a low-loss external cavity such that the external cavity—not the sub-cavities—determines the beam properties. A near-Gaussian beam of 4.3° × 5.1° divergence is observed and an output power level >5 mW is achieved. The polarized response of the metasurface allows the use of a wire-grid polarizer as an output coupler that is continuously tunable.

  3. Experimental investigation of cavity flows

    Energy Technology Data Exchange (ETDEWEB)

    Loeland, Tore

    1998-12-31

    This thesis uses LDV (Laser Doppler Velocimetry), PIV (Particle Image Velocimetry) and Laser Sheet flow Visualisation to study flow inside three different cavity configurations. For sloping cavities, the vortex structure inside the cavities is found to depend upon the flow direction past the cavity. The shape of the downstream corner is a key factor in destroying the boundary layer flow entering the cavity. The experimental results agree well with numerical simulations of the same geometrical configurations. The results of the investigations are used to find the influence of the cavity flow on the accuracy of the ultrasonic flowmeter. A method to compensate for the cavity velocities is suggested. It is found that the relative deviation caused by the cavity velocities depend linearly on the pipe flow. It appears that the flow inside the cavities should not be neglected as done in the draft for the ISO technical report on ultrasonic flowmeters. 58 refs., 147 figs., 2 tabs.

  4. SPS accelerating cavity

    CERN Multimedia

    1983-01-01

    See photo 8302397: View from the downstream end of one of the SPS accelerating cavities (200 MHz, travelling wave structure). See 7603195 and 8011289 for more details, 7411032 for the travelling wave structure, and also 8104138. Giacomo Primadei stands on the left.

  5. Laser cavity modelling

    OpenAIRE

    Damakoa, I.; Audounet, J.; Bouyssou, G.; Vassilieff, G.

    1993-01-01

    Two approachs of modelling nonhomogeneous cavity laser are presented. They are based on the beam propagation method which allows the use of fast Fourier transform (FFT). The resulting procedures provide selfconsistent solutions to the Maxwell and diffusion equations. Results are given to illustrate the two methods.


  6. LEP superconducting cavity

    CERN Multimedia

    1995-01-01

    Engineers work in a clean room on one of the superconducting cavities for the upgrade to the LEP accelerator, known as LEP-2. The use of superconductors allow higher electric fields to be produced so that higher beam energies can be reached.

  7. Cavity launchers for ICRF

    International Nuclear Information System (INIS)

    A type of resonant coil cavity is analyzed as a launcher for ICRF. This approach offers the advantages of: (1) convenient and flexible sizing, (2) ease of operation and maintenance, and (3) high power handling capability. We present results for resonance conditions, mode structures, power handling capabilities, and sensitivity to variation in plasma parameters

  8. Statistical electromagnetics: Complex cavities

    NARCIS (Netherlands)

    Naus, H.W.L.

    2008-01-01

    A selection of the literature on the statistical description of electromagnetic fields and complex cavities is concisely reviewed. Some essential concepts, for example, the application of the central limit theorem and the maximum entropy principle, are scrutinized. Implicit assumptions, biased choic

  9. What's a Cavity?

    Science.gov (United States)

    ... and deeper over time. Cavities are also called dental caries (say: KARE-eez), and if you have a ... made up mostly of the germs that cause tooth decay. The bacteria in your mouth make acids and when plaque clings to your teeth, the acids can eat away at the outermost ...

  10. Niobium superconducting cavity

    CERN Multimedia

    1980-01-01

    This 5-cell superconducting cavity, made from bulk-Nb, stems from the period of general studies, not all directed towards direct use at LEP. This one is dimensioned for 1.5 GHz, the frequency used at CEBAF and also studied at Saclay (LEP RF was 352.2 MHz). See also 7908227, 8007354, 8209255, 8210054, 8312339.

  11. Implosion of the small cavity and large cavity cannonball targets

    International Nuclear Information System (INIS)

    Recent results of cannonball target implosion research are briefly reviewed with theoretical predictions for GEKKO XII experiments. The cannonball targets are classified into two types according to the cavity size ; small cavity and large cavity. The compression mechanisms of the two types are discussed. (author)

  12. Deep-UV Rayleigh scattering of N2, CH4 and SF6

    NARCIS (Netherlands)

    Ityaksov, D.; Linnartz, H.V.J.; Ubachs, W.M.G.

    2008-01-01

    Rayleigh scattering room temperature cross-section values of N2, CH4 and SF6 have been obtained between 198 and 270 nm by combining cavity ring-down spectroscopy (CRDS) and pressure ramp measurements. The experimental data have been fitted to a functional representation, describing the 1/4 like beha

  13. The IAGOS-core greenhouse gas package : a measurement system for continuous airborne observations of CO2, CH4, H2O and CO

    NARCIS (Netherlands)

    Filges, Annette; Gerbig, Christoph; Chen, Huilin; Franke, Harald; Klaus, Christoph; Jordan, Armin

    2015-01-01

    Within the framework of IAGOS-ERI (In-service Aircraft for a Global Observing System - European Research Infrastructure), a cavity ring-down spectroscopy (CRDS)-based measurement system for the autonomous measurement of the greenhouse gases (GHGs) CO2 and CH4, as well as CO and water vapour was desi

  14. Contribution of carbonyl photochemistry to aging of atmospheric secondary organic aerosol

    DEFF Research Database (Denmark)

    Mang, Stephen A.; Henricksen, Dana K.; Bateman, Adam P.;

    2008-01-01

    in situ by infrared cavity ring-down spectroscopy. A number of additional gas-phase products of SOA photodegradation were observed by gas chromatography, including methane, ethene, acetaldehyde, acetone, methanol, and I-butene. The absorption spectrum of SOA material collected onto CaF, windows was...

  15. Seamless/bonded niobium cavities

    Science.gov (United States)

    Singer, W.

    2006-07-01

    Technological aspects and performance of seamless cavities produced by hydroforming are presented. Problems related to the fabrication of seamless cavities from bulk niobium are mainly solved thanks to the progress of the last years. The highest achieved accelerating gradients are comparable for both seamless and welded versions (ca. 40 MV/m) Nevertheless further development of seamless cavities is desirable in order to avoid the careful preparation of parts for welding and get reliable statistic. Fabrication of NbCu clad cavities from bimetallic tubes is an interesting option that gives new opportunity to the seamless technique. On the one hand it allows reducing the niobium costs contribution; on the other hand it increases the thermal stability of the cavity. The highest accelerating gradient achieved on seamless NbCu clad single cell cavities (ca. 40 MV/m) is comparable to the one reached on bulk Nb cavities. Fabrication of multi-cell NbCu cavities by hydroforming was recently proven.

  16. Changeability of Oral Cavity Environment

    OpenAIRE

    Surdacka, Anna; Strzyka³a, Krystyna; Rydzewska, Anna

    2007-01-01

    Objectives In dentistry, the results of in vivo studies on drugs, dental fillings or prostheses are routinely evaluated based on selected oral cavity environment parameters at specific time points. Such evaluation may be confounded by ongoing changes in the oral cavity environment induced by diet, drug use, stress and other factors. The study aimed to confirm oral cavity environment changeability. Methods 24 healthy individuals aged 20–30 had their oral cavity environment prepared by having p...

  17. Effective optical path length for tandem diffuse cubic cavities as gas absorption cell

    International Nuclear Information System (INIS)

    Tandem diffuse cubic cavities designed by connecting two single diffuse cubic-shaped cavities, A and B, with an aperture (port fraction fap) in the middle of the connecting baffle was developed as a gas absorption cell. The effective optical path length (EOPL) was evaluated by comparing the oxygen absorption signal in the cavity and in air based on tunable diode laser absorption spectroscopy (TDLAS). Experimental results manifested an enhancement of EOPL for the tandem diffuse cubic cavities as the decrease of fap and can be expressed as the sum of EOPL of two single cubic cavities at fap < 0.01, which coincided well with theoretical analysis. The simulating EOPL was smaller than experimental results at fap > 0.01, which indicated that back scattering light from cavity B to cavity A cannot be ignored at this condition. (paper)

  18. Plasma Treatment of Single-Cell Niobium SRF Cavities

    Energy Technology Data Exchange (ETDEWEB)

    J. Upadhyay, M. Nikolić, S. Popović, L. Vušković, H.L. Phillips, A-M. Valente-Feliciano

    2011-03-01

    Superconducting radio frequency cavities of bulk Niobium are integral components of particle accelerators based on superconducting technology. Wet chemical processing is the commonly used procedure for impurities and surface defects removal and surface roughness improvement , both required to improve the RF performance of the cavity. We are studying plasma etching as an alternate technique to process these cavities. The uniformity of the plasma sheath at the inner wall of the cavity is one prerequisite for its uniform etching. We are developing electro-optic diagnostic techniques to assess the plasma uniformity. Multiple electro-optical probes are placed at different locations of the single cell cavity to diagnose the electrical and optical properties of the plasma. The electrical parameters are required to understand the kinetic nature of the plasma and the optical emission spectroscopy provides the spatial distribution of radicals in the plasma. The spatial variation of the plasma parameters inside the cavity and their effect on the etching of niobium samples placed at different locations in the cavity will be presented.

  19. Colloquium: cavity optomechanics

    CERN Multimedia

    2011-01-01

    Monday 14 November 2011, 17:00 Ecole de Physique, Auditoire Stueckelberg Université de Genève Cavity optomechanics: controlling micro mechanical oscillators with laser light Prof. Tobias Kippenberg EPFL, Lausanne Laser light can be used to cool and to control trapped ions, atoms and molecules at the quantum level. This has lead to spectacular advances such as the most precise atomic clocks. An outstanding frontier is the control with lasers of nano- and micro-mechancial systems. Recent advances in cavity optomechanics have allowed such elementary control for the first time, enabling mechanical systems to be ground state cooled leading to readout with quantum limited sensitivity and permitting to explore new device concepts resulting from radiation pressure.  

  20. RF superconducting cavities

    CERN Document Server

    Kojima, Y

    1980-01-01

    The history and present activity in research on RF superconducting cavities in various countries are reviewed. The program of the July 1980 Karlsruhe workshop is reproduced and research activity in this field at Stanford HEPL and SLAC, Cornell, Oregon, Brookhaven, KEK (Japan), Weismann (Israel), Genoa, CERN and Karlsruhe (KfK) listed. The theoretical basis of surface resistance and intracavity magnetic field, multipacing and non-resonant electron loading are outlined. (20 refs).

  1. Entangling atoms in bad cavities

    OpenAIRE

    Sorensen, Anders S.; Molmer, Klaus

    2002-01-01

    We propose a method to produce entangled spin squeezed states of a large number of atoms inside an optical cavity. By illuminating the atoms with bichromatic light, the coupling to the cavity induces pairwise exchange of excitations which entangles the atoms. Unlike most proposals for entangling atoms by cavity QED, our proposal does not require the strong coupling regime g^2/\\kappa\\Gamma>> 1, where g is the atom cavity coupling strength, \\kappa is the cavity decay rate, and \\Gamma is the dec...

  2. Cavity Backed Slot Antenna

    Directory of Open Access Journals (Sweden)

    Sarang Masani, Ila Parmar, Hitendra Jadeja

    2013-05-01

    Full Text Available Among the current driving forces in wireless communications, there is a need for compact, efficient, inexpensive and reproducible antennas. In some instances, particularly long-distance applications, radiators with directive, high-gain characteristics are necessary. This paper proposes a cavity-backed slot antenna to that end. This antenna will enhance the gain, directivity and can also be easily flush mounted to the flying object. The shape and size of the slot can be effectively utilized to get the desired result. The proposed antenna is feed by waveguide which facilitate it to be applicable at high power operation where coaxial cable fails due to skin effect. Present antenna is verified using Numerical Technique called Finite Element Method FEM. The conception of this antenna is realized by the software HFSS “Ansoft-High Frequency Structure Simulator”. By properly selecting shapes, dimensions of the slots and number of slot affects the parameters like return loss, gain along Θ, Ø directions, Cartesian plot and radiation pattern .The Backing of cavity to the slot antenna provide the basics of the gain enhancement and the slot loading effect and the cavity volume plays an important role in achieving the desired return loss at the specific frequency.The simulated antenna shows the 7.0944 db of gain and return loss of -28.60. The proposed antenna works at 6 GHz.

  3. Graphene intracavity spaser absorption spectroscopy

    Science.gov (United States)

    Lozovik, Yu. E.; Nechepurenko, I. A.; Dorofeenko, A. V.

    2016-09-01

    We propose an intracavity plasmon absorption spectroscopy method based on graphene active plasmonics. It is shown that the plasmonic cavity contribution to the sensitivity is proportional to the quality factor Q of the graphene plasmonic cavity and reaches two orders of magnitude. The addition of gain medium into the cavity increases the sensitivity of method. Maximum sensitivity is reached in the vicinity of the plasmon generation threshold. The gain contribution to the sensitivity is proportional to Q1/2. The giant amplification of sensitivity in the graphene plasmon generator is associated with a huge path length, limited only by the decoherence processes. An analytical estimation of the sensitivity to loss caused by analyzed particles (molecules, nanoparticles, etc.) normalized by the single pass plasmon scheme is derived. Usage of graphene nanoflakes as plasmonic cavity allows a high spatial resolution to be reached, in addition to high sensitivity.

  4. Crab Cavities for Linear Colliders

    International Nuclear Information System (INIS)

    Crab cavities have been proposed for a wide number of accelerators and interest in crab cavities has recently increased after the successful operation of a pair of crab cavities in KEK-B. In particular crab cavities are required for both the ILC and CLIC linear colliders for bunch alignment. Consideration of bunch structure and size constraints favour a 3.9 GHz superconducting, multi-cell cavity as the solution for ILC, whilst bunch structure and beam-loading considerations suggest an X-band copper travelling wave structure for CLIC. These two cavity solutions are very different in design but share complex design issues. Phase stabilisation, beam loading, wakefields and mode damping are fundamental issues for these crab cavities. Requirements and potential design solutions will be discussed for both colliders.

  5. Crab Cavities for Linear Colliders

    Energy Technology Data Exchange (ETDEWEB)

    Burt, G.; Ambattu, P.; Carter, R.; Dexter, A.; Tahir, I.; /Cockcroft Inst. Accel. Sci. Tech. /Lancaster U.; Beard, C.; Dykes, M.; Goudket, P.; Kalinin, A.; Ma, L.; McIntosh, P.; /Daresbury; Shulte, D.; /CERN; Jones, Roger M.; /Cockcroft Inst. Accel. Sci. Tech. /Manchester U.; Bellantoni, L.; Chase, B.; Church, M.; Khabouline, T.; Latina, A.; /Fermilab; Adolphsen, C.; Li, Z.; Seryi, Andrei; /SLAC

    2011-11-08

    Crab cavities have been proposed for a wide number of accelerators and interest in crab cavities has recently increased after the successful operation of a pair of crab cavities in KEK-B. In particular crab cavities are required for both the ILC and CLIC linear colliders for bunch alignment. Consideration of bunch structure and size constraints favour a 3.9 GHz superconducting, multi-cell cavity as the solution for ILC, whilst bunch structure and beam-loading considerations suggest an X-band copper travelling wave structure for CLIC. These two cavity solutions are very different in design but share complex design issues. Phase stabilisation, beam loading, wakefields and mode damping are fundamental issues for these crab cavities. Requirements and potential design solutions will be discussed for both colliders.

  6. Crab cavities for linear colliders

    CERN Document Server

    Burt, G; Carter, R; Dexter, A; Tahir, I; Beard, C; Dykes, M; Goudket, P; Kalinin, A; Ma, L; McIntosh, P; Shulte, D; Jones, Roger M; Bellantoni, L; Chase, B; Church, M; Khabouline, T; Latina, A; Adolphsen, C; Li, Z; Seryi, Andrei; Xiao, L

    2008-01-01

    Crab cavities have been proposed for a wide number of accelerators and interest in crab cavities has recently increased after the successful operation of a pair of crab cavities in KEK-B. In particular crab cavities are required for both the ILC and CLIC linear colliders for bunch alignment. Consideration of bunch structure and size constraints favour a 3.9 GHz superconducting, multi-cell cavity as the solution for ILC, whilst bunch structure and beam-loading considerations suggest an X-band copper travelling wave structure for CLIC. These two cavity solutions are very different in design but share complex design issues. Phase stabilisation, beam loading, wakefields and mode damping are fundamental issues for these crab cavities. Requirements and potential design solutions will be discussed for both colliders.

  7. ISR RF cavities

    CERN Multimedia

    1983-01-01

    In each ISR ring the radiofrequency cavities were installed in one 9 m long straight section. The RF system of the ISR had the main purpose to stack buckets of particles (most of the time protons)coming from the CPS and also to accelerate the stacked beam. The installed RF power per ring was 18 kW giving a peak accelerating voltage of 20 kV. The system had a very fine regulation feature allowing to lower the voltage down to 75 V in a smooth and well controlled fashion.

  8. Stabilization of an optical frequency comb to an external cavity

    OpenAIRE

    Rydberg, Olof

    2014-01-01

    The subject of this master's thesis is stabilizing a frequency comb laser to an external cavity using a couple of servo controllers. The aim of the project was to build a pair of servo controllers, replacing parts of the existing commercial and proprietary solution already in use. The system under control is an optical frequency comb, which is locked to an external cavity and is used for trace gas detection and spectroscopy. The comb is a broadband light source and needs to be locked to the e...

  9. Frequency control of radiofrequency cavity

    OpenAIRE

    Menart, Jure

    2014-01-01

    This work describes the design, development and application of the system for frequency control of EMMA accelerator radiofrequency cavity. The problem with the radiofrequency cavities is, that because of various factors (change in the environmental temperature, mechanical stress, ...), they are continuously frequency detuning. The consequence of the frequency detuning is that electromagnetic field in the cavity is not optimal for the acceleration of the particles. For this reason the resonant...

  10. Single ion cavity QED experiments

    International Nuclear Information System (INIS)

    Full text: We have set up a spherical Paul trap for a storing a single Ca+ ion placed in the center of a high finesse near confocal resonator. We report on experiments demonstrating the coupling of the narrow S1/2-D5/2 transition to the cavity internal light field. Due to the coupling, the ion acts as sensitive probe for the cavity internal field. We are able to map the field distribution by measuring the excitation probability. Scanning the cavity over the resonance imprints a Doppler frequency shift on the cavity field which leads to a spectral shift and a asymmetric broadening of the S-D transition. (author)

  11. Cavity coalescence in superplastic deformation

    Energy Technology Data Exchange (ETDEWEB)

    Stowell, M.J.; Livesey, D.W.; Ridley, N.

    1984-01-01

    An analysis of the probability distribution function of particles randomly dispersed in a solid has been applied to cavitation during superplastic deformation and a method of predicting cavity coalescence developed. Cavity size distribution data were obtained from two microduplex nickel-silver alloys deformed superplastically to various extents at elevated temperature, and compared to theoretical predictions. Excellent agreement occurred for small void sizes but the model underestimated the number of voids in the largest size groups. It is argued that the discrepancy results from a combination of effects due to non-random cavity distributions and to enhanced growth rates and incomplete spheroidization of the largest cavities.

  12. Surface state photonic bandgap cavities

    OpenAIRE

    Rahachou, A. I.; Zozoulenko, I. V.

    2005-01-01

    We propose and analyze a new type of a resonant high-Q cavity for lasing, sensing or filtering applications, which is based on a surface states of a finite photonic crystal. We demonstrate that such the cavity can have a Q factor comparable with that one of conventional photonic band-gap defect mode cavities. At the same time, the distinguished feature of the surface mode cavity is that it is situated directly at the surface of the photonic crystal. This might open up new possibilities for de...

  13. Nanofriction in Cavity Quantum Electrodynamics.

    Science.gov (United States)

    Fogarty, T; Cormick, C; Landa, H; Stojanović, Vladimir M; Demler, E; Morigi, Giovanna

    2015-12-01

    The dynamics of cold trapped ions in a high-finesse resonator results from the interplay between the long-range Coulomb repulsion and the cavity-induced interactions. The latter are due to multiple scatterings of laser photons inside the cavity and become relevant when the laser pump is sufficiently strong to overcome photon decay. We study the stationary states of ions coupled with a mode of a standing-wave cavity as a function of the cavity and laser parameters, when the typical length scales of the two self-organizing processes, Coulomb crystallization and photon-mediated interactions, are incommensurate. The dynamics are frustrated and in specific limiting cases can be cast in terms of the Frenkel-Kontorova model, which reproduces features of friction in one dimension. We numerically recover the sliding and pinned phases. For strong cavity nonlinearities, they are in general separated by bistable regions where superlubric and stick-slip dynamics coexist. The cavity, moreover, acts as a thermal reservoir and can cool the chain vibrations to temperatures controlled by the cavity parameters and by the ions' phase. These features are imprinted in the radiation emitted by the cavity, which is readily measurable in state-of-the-art setups of cavity quantum electrodynamics. PMID:26684118

  14. Using a high finesse optical resonator to provide a long light path for differential optical absorption spectroscopy: CE-DOAS

    OpenAIRE

    J. Meinen; J. Thieser; U. Platt; T. Leisner

    2008-01-01

    Cavity enhanced methods in absorption spectroscopy have seen a considerable increase in popularity during the past decade. Especially Cavity Enhanced Absorption Spectroscopy (CEAS) established itself in atmospheric trace gas detection by providing tens of kilometers of effective light path length using a cavity as short as 1 m. In this paper we report on the construction and testing of a compact and power efficient light emitting diode based broadband Cavity Enhanced Differential Optical Abso...

  15. Two-cavity gyroklystron with self-excited input cavity

    Energy Technology Data Exchange (ETDEWEB)

    Sokolov, E.V.; Zasypkin, E.V. [Inst. of Applied Physics, Novgorod (Russian Federation)

    1995-12-31

    A new type of gyro-oscillator-two cavity gyroklystron with self-excited input cavity (or, for simplicity, two-cavity gyrokylstron oscillator) is proposed. In this device, the autooscillations excited in the first cavity modulate electrons by energy, electrons are bunched in the drift space, and then the bunches excite powerful oscillations in the second (output) cavity. Since, as in gyroklystron, the optimal second cavity length L{sub 2} does not exceed 2-2.5 {lambda} ({lambda} is the operating wavelength), its Q-factor Q{sub 2} {approximately} (L{sub 2}/{lambda}){sup 2} should be essentially lower than cavity Q-factor of a traditional gyrotron. It allows to diminish the RF ohmic losses in the second cavity and to enhance the output power without the efficiency reduction. A simplest theory of such oscillator has been developed. Predicted by theory, the output power enhancement (in comparison with that for an ordinary gyrotron) has been demonstrated experimentally.

  16. Frequency Tuning for a DQW Crab Cavity

    CERN Document Server

    Verdú-Andrés, Silvia; Ben-Zvi, Ilan; Calaga, Rama; Capatina, Ofelia; Leuxe, Raphael; Skaritka, John; Wu, Qiong; Xiao, Binping; Zanoni, Carlo

    2016-01-01

    The nominal operating frequency for the HL-LHC crab cavities is 400.79 MHz within a bandwidth of ±60kHz. Attaining the required cavity tune implies a good understanding of all the processes that influence the cavity frequency from the moment when the cavity parts are being fabricated until the cavity is installed and under operation. Different tuning options will be available for the DQW crab cavity of LHC. This paper details the different steps in the cavity fabrication and preparation that may introduce a shift in the cavity frequency and introduces the different tuning methods foreseen to bring the cavity frequency to meet the specifications.

  17. A Scanning Cavity Microscope

    CERN Document Server

    Mader, Matthias; Hänsch, Theodor W; Hunger, David

    2014-01-01

    Imaging of the optical properties of individual nanosystems beyond fluorescence can provide a wealth of information. However, the minute signals for absorption and dispersion are challenging to observe, and only specialized techniques requiring sophisticated noise rejection are available. Here we use signal enhancement in a scanning optical microcavity to demonstrate ultra-sensitive imaging. Harnessing multiple interactions of probe light with a sample within an optical resonator, we achieve a 1700-fold signal enhancement compared to diffraction-limited microscopy. We demonstrate quantitative imaging of the extinction cross section of gold nanoparticles with a sensitivity below 1 nm2, we show a method to improve spatial resolution potentially below the diffraction limit by using higher order cavity modes, and we present measurements of the birefringence and extinction contrast of gold nanorods. The demonstrated simultaneous enhancement of absorptive and dispersive signals promises intriguing potential for opt...

  18. Superconducting cavity model for LEP

    CERN Multimedia

    1979-01-01

    A superconducting cavity model is being prepared for testing in a vertical cryostat.At the top of the assembly jig is H.Preis while A.Scharding adjusts some diagnostic equipment to the cavity. See also photo 7912501X.

  19. Fiber cavities for atom chips

    OpenAIRE

    Klappauf, B.G.; Horak, P.; Kazansky, P. G.

    2003-01-01

    We present experimental realizations of several micro-cavities, constructed from standard fiber optic components, which meet the theoretical criteria for single atom detection from laser-cooled samples. We discuss integration of these cavities into state-of-the-art 'atom chips'.

  20. Design of a cavity filter

    International Nuclear Information System (INIS)

    A cavity filter was developed for the SSRF 0-mode beam feedback. The filter is used to pick up the 500 MHz signal from the storage ring beam. The Superfish was used to simulate the model of the cavity bandpass filter. The design method, parameters of the filter and results of beam measurements are described in this paper. (authors)

  1. Study on superconducting accelerating cavities

    International Nuclear Information System (INIS)

    A test cavity of cylindrical shape has been designed and constructed to study superconducting accelerating cavities for TRISTAN e+e- Ring. Higher order modes have been calculated by using SUPERFISH program and an analytical method, and measured. The measured resonant frequencies well agree with the calculated results. (author)

  2. Technical tasks in superconducting cavities

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Kenji [High Energy Accelerator Research Organization, Tsukuba, Ibaraki (Japan)

    1997-11-01

    The feature of superconducting rf cavities is an extremely small surface resistance on the wall. It brings a large energy saving in the operation, even those are cooled with liquid helium. That also makes possible to operate themselves in a higher field gradient comparing to normal conducting cavities, and brings to make accelerators compact. These merits are very important for the future accelerator engineering which is planed at JAERI for the neutron material science and nuclear waste transmutation. This machine is a high intensity proton linac and uses sc cavities in the medium and high {beta} sections. In this paper, starting R and D of proton superconducting cavities, several important technical points which come from the small surface resistance of sc cavities, are present to succeed it and also differences between the medium and high - {beta} structures are discussed. (author)

  3. Mechanical Properties of Niobium Cavities

    Energy Technology Data Exchange (ETDEWEB)

    Ciovati, Gianluigi [Thomas Jefferson National Accelerator Facility, Newport News, VA (United States); Dhakal, Pashupati [Thomas Jefferson National Accelerator Facility, Newport News, VA (United States); Matalevich, Joseph R. [Thomas Jefferson National Accelerator Facility, Newport News, VA (United States); Myneni, Ganapati Rao [Thomas Jefferson National Accelerator Facility, Newport News, VA (United States)

    2015-09-01

    The mechanical stability of bulk Nb cavity is an important aspect to be considered in relation to cavity material, geometry and treatments. Mechanical properties of Nb are typically obtained from uniaxial tensile tests of small samples. In this contribution we report the results of measurements of the resonant frequency and local strain along the contour of single-cell cavities made of ingot and fine-grain Nb of different purity subjected to increasing uniform differential pressure, up to 6 atm. Measurements have been done on cavities subjected to different heat treatments. Good agreement between finite element analysis simulations and experimental data in the elastic regime was obtained with a single set of values of Young’s modulus and Poisson’s ratio. The experimental results indicate that the yield strength of medium-purity ingot Nb cavities is higher than that of fine-grain, high-purity Nb.

  4. A (nearly) complete experimental linelist for 13C16O2, 16O13C18O, 16O13C17O, 13C18O2 and 17O13C18O by high-sensitivity CW-CRDS spectroscopy between 5851 and 7045 cm-1

    International Nuclear Information System (INIS)

    An experimental database for the 13C16O2, 16O13C18O, 16O13C17O, 13C18O2 and 17O13C18O isotopologues of carbon dioxide has been constructed on the basis of the high-sensitivity absorption spectrum of carbon dioxide with 99% enrichment in 13C recorded by CW-cavity ring down spectroscopy (CW-CRDS) between 5851 and 7045 cm-1. As a result of the achieved sensitivity (typical noise equivalent absorption αmin∼2-5x10-10 cm-1) combined with the high linearity and dynamics (more than four decades) of the CW-CRDS technique, the amount of spectroscopic information contained in these spectra was considerable. A total of 8639 transitions of the 13C16O2, 16O13C18O, 16O13C17O, 13C18O2 and 17O13C18O isotopologues with line strength as low as 5x10-29 cm/molecule were assigned. They belong to a total of 150 bands, while less than 20 bands were previously reported by Fourier transform spectroscopy. The excellent agreement between the predictions of the effective operators model and the observations has allowed using an automatic search program to assign the weaker lines observed in the congested spectrum. The spectroscopic parameters of the vibrational upper levels were obtained from a fit of the measured line positions. A number of resonance interactions were observed; in particular, several occurrences of interpolyad anharmonic couplings not included in the polyad model of effective Hamiltonian, were found to affect a few bands of the 16O13C18O and 16O13C17O isotopologues. In the list of 8639 transitions, which are provided as Supplementary material, line positions are experimental values (typical uncertainty in the order of 1x10-3 cm-1), while line strengths were calculated at 296 K by using the effective operators approach (typical uncertainty in the order of 5%). In the case of the 13C16O2 isotopologue, the reported transitions represent 99.65% of the total absorbance in the region considered

  5. Cavity-Enhanced Gas Analyzer for In-Situ Sampling of Biogenic Gases and Their Isotopes Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Small Business Innovation Research Phase I project concerns the novel application of cavity-enhanced absorption spectroscopy to quantify biogenic gases (CH4,...

  6. New developed cylindrical TM010 mode EPR cavity for X-band in vivo tooth dosimetry.

    Directory of Open Access Journals (Sweden)

    Guo Junwang

    Full Text Available EPR tooth in vivo dosimetry is an attractive approach for initial triage after unexpected nuclear events. An X-band cylindrical TM010 mode resonant cavity was developed for in vivo tooth dosimetry and used in EPR applications for the first time. The cavity had a trapezoidal measuring aperture at the exact position of the cavity's cylindrical wall where strong microwave magnetic field H1 concentrated and weak microwave electric field E1 distributed. Theoretical calculations and simulations were used to design and optimize the cavity parameters. The cavity features were evaluated by measuring DPPH sample, intact incisor samples embed in a gum model and the rhesus monkey teeth. The results showed that the cavity worked at designed frequency and had the ability to make EPR spectroscopy in relative high sensitivity. Sufficient modulation amplitude and microwave power could be applied into the aperture. Radiation induced EPR signal could be observed remarkably from 1 Gy irradiated intact incisor within only 30 seconds, which was among the best in scan time and detection limit. The in vivo spectroscopy was also realized by acquiring the radiation induced EPR signal from teeth of rhesus monkey whose teeth was irradiated by dose of 2 Gy. The results suggested that the cavity was sensitive to meet the demand to assess doses of significant level in short time. This cavity provided a very potential option for the development of X-band in vivo dosimetry.

  7. New developed cylindrical TM010 mode EPR cavity for X-band in vivo tooth dosimetry.

    Science.gov (United States)

    Junwang, Guo; Qingquan, Yuan; Jianbo, Cong; Lei, Ma; Guofu, Dong; Guoshan, Yang; Ke, Wu

    2014-01-01

    EPR tooth in vivo dosimetry is an attractive approach for initial triage after unexpected nuclear events. An X-band cylindrical TM010 mode resonant cavity was developed for in vivo tooth dosimetry and used in EPR applications for the first time. The cavity had a trapezoidal measuring aperture at the exact position of the cavity's cylindrical wall where strong microwave magnetic field H1 concentrated and weak microwave electric field E1 distributed. Theoretical calculations and simulations were used to design and optimize the cavity parameters. The cavity features were evaluated by measuring DPPH sample, intact incisor samples embed in a gum model and the rhesus monkey teeth. The results showed that the cavity worked at designed frequency and had the ability to make EPR spectroscopy in relative high sensitivity. Sufficient modulation amplitude and microwave power could be applied into the aperture. Radiation induced EPR signal could be observed remarkably from 1 Gy irradiated intact incisor within only 30 seconds, which was among the best in scan time and detection limit. The in vivo spectroscopy was also realized by acquiring the radiation induced EPR signal from teeth of rhesus monkey whose teeth was irradiated by dose of 2 Gy. The results suggested that the cavity was sensitive to meet the demand to assess doses of significant level in short time. This cavity provided a very potential option for the development of X-band in vivo dosimetry. PMID:25222483

  8. Frequency-feedback cavity enhanced spectrometer

    Science.gov (United States)

    Hovde, David Christian; Gomez, Anthony

    2015-08-18

    A spectrometer comprising an optical cavity, a light source capable of producing light at one or more wavelengths transmitted by the cavity and with the light directed at the cavity, a detector and optics positioned to collect light transmitted by the cavity, feedback electronics causing oscillation of amplitude of the optical signal on the detector at a frequency that depends on cavity losses, and a sensor measuring the oscillation frequency to determine the cavity losses.

  9. Cavity beam position monitors

    International Nuclear Information System (INIS)

    Beam-based alignment and feedback systems are essential for the operation of future linear colliders and free electron lasers. A certain number of beam position monitors with a resolution in the submicron range are needed at selected locations. Most beam position monitors detect the electric or the magnetic field excited by a beam of charged particles at different locations around the beam pipe. In resonant monitors, however, the excitation of special field configurations by an off-center beam is detected. These structures offer a large signal per micron displacement. This paper is an attempt to summarize the fundamental characteristics of resonant monitors, their advantages and shortcomings. Emphasis will be on the design of cylindrical cavities, in particular on the estimation of expected signals, of resolution limits and the resulting beam distortion. This includes also a short introduction into numerical methods. Fabrication, tuning, and other practical problems will be reviewed briefly. Finally, some resonant devices used for beam position diagnostics will be discussed and listed

  10. Three-dimensional cavity calculations

    International Nuclear Information System (INIS)

    The existence of a code that solves for the resonant electromagnetic modes of oscillation in arbitrarily-shaped three-dimensional cavities opens new possibilities in rf-structure analysis and research. The URMEL-3D code, the product of a multi-year collaboration between DESY, KFA-Juelich, and Los Alamos, has been used in some exploratory studies to determine the feasibility of using a 3-D code to calculate the properties of several practical rf structures. The results are reported here for three cases: the jungle gym, two coupled cavities, and a waveguide-cavity coupling problem

  11. Beam - cavity interaction beam loading

    International Nuclear Information System (INIS)

    The interaction of a beam with a cavity and a generator in cyclic accelerators or storage rings is investigated. Application of Maxwell's equations together with the nonuniform boundary condition allows one to get an equivalent circuit for a beam-loaded cavity. The general equation for beam loading is obtained on the basis of the equivalent circuit, and the beam admittance is calculated. Formulas for power consumption by a beam-loaded cavity are derived, and the optimal tuning and coupling factor are analyzed. (author)

  12. Development of a cavity enhanced aerosol albedometer

    Directory of Open Access Journals (Sweden)

    W. Zhao

    2014-03-01

    Full Text Available We report on the development of a cavity enhanced aerosol single scattering albedometer incorporating incoherent broad-band cavity-enhanced spectroscopy (IBBCEAS approach and an integrating sphere (IS for simultaneous in situ measurements of aerosol scattering and extinction coefficients in the exact same sample volume. The cavity enhanced albedometer employed a blue light-emitting diode (LED based IBBCEAS approach for the measurement of wavelength-resolved aerosol optical extinction over the spectral range of 445–480 nm. An integrating sphere nephelometer coupled to the IBBCEAS setup was used for the measurement of aerosol scattering. The scattering signal was measured with a single channel photomultiplier tube (PMT, providing an integrated value over a narrow bandwidth (FWHM ~ 9 nm in the spectral region of 465–474 nm. A scattering coefficient at a wavelength of 470 nm was deduced as an averaged scattering value and used for data analysis and instrumental performance comparison. Performance evaluation of the albedometer was carried out using laboratory-generated particles and ambient aerosol. The scattering and extinction measurements of monodisperse polystyrene latex (PSL spheres generated in laboratory proved excellent correlation between two channels of the albedometer. The retrieved refractive index (RI from the measured scattering and extinction efficiencies agreed well with the values reported in previously published papers. Aerosol light scattering and extinction coefficients, single scattering albedo (SSA and NO2 concentrations in an ambient sample were directly and simultaneously measured using the developed albedometer. The developed instrument was validated via an intercomparison of the measured aerosol scattering coefficient and NO2 trace concentration against a TSI 3563 integrating nephelometer and a chemiluminescence detector, respectively.

  13. Transferring a cavity field entangled state in cavity QED

    Energy Technology Data Exchange (ETDEWEB)

    Ye Liu [Anhui Key Laboratory of Information Material and Devices, School of Physics and Material Science, Anhui University, Hefei 230039 (China); Guo Guangcan [Key Laboratory of Quantum Information, University of Science and Technology of China, Chinese Academy of Sciences, Hefei 230026 (China)

    2005-08-01

    We propose a scheme for transferring an entanglement of zero- and one-photon states from one cavity to another. The scheme, which has 100% success probability, is mainly based on a two-mode cavity dispersively interacting with a three-level atom in the {lambda} configuration and does not involve Bell-state measurement. This scheme can also be used to teleport an unknown atomic state.

  14. SRF Cavity Fabrication and Materials

    CERN Document Server

    Singer, W

    2014-01-01

    The technological and metallurgical requirements of material for highgradient superconducting cavities are described. High-purity niobium, as the preferred metal for the fabrication of superconducting accelerating cavities, should meet exact specifications. The content of interstitial impurities such as oxygen, nitrogen, and carbon must be below 10μg/g. The hydrogen content should be kept below 2μg/g to prevent degradation of the Q-value under certain cool-down conditions. The material should be free of flaws (foreign material inclusions or cracks and laminations) that can initiate a thermal breakdown. Defects may be detected by quality control methods such as eddy current scanning and identified by a number of special methods. Conventional and alternative cavity fabrication methods are reviewed. Conventionally, niobium cavities are fabricated from sheet niobium by the formation of half-cells by deep drawing, followed by trim machining and Electron-Beam Welding (EBW). The welding of half-cells is a delicate...

  15. Niobium LEP 2 accelerating cavities

    CERN Multimedia

    An accelerating cavity from LEP. This could be cut open to show the layer of niobium on the inside. Operating at 4.2 degrees above absolute zero, the niobium is superconducting and carries an accelerating field of 6 million volts per metre with negligible losses. Each cavity has a surface of 6 m2. The niobium layer is only 1.2 microns thick, ten times thinner than a hair. Such a large area had never been coated to such a high accuracy. A speck of dust could ruin the performance of the whole cavity so the work had to be done in an extremely clean environment. These challenging requirements pushed European industry to new achievements. 256 of these cavities were used in an upgrade of the LEP accelerator to double the energy of the particle beams.

  16. Geometry-Invariant Resonant Cavities

    CERN Document Server

    Liberal, Iñigo; Engheta, Nader

    2015-01-01

    Resonant cavities are one of the basic building blocks in various disciplines of science and technology, with numerous applications ranging from abstract theoretical modeling to everyday life devices. The eigenfrequencies of conventional cavities are a function of its geometry, and, thus, the size and shape of a resonant cavity is selected in order to operate at a specific frequency. Here, we demonstrate theoretically the existence of geometry-invariant resonant cavities, i.e., resonators whose eigenfrequency is invariant with respect to geometrical deformations. This effect is obtained by exploiting the unusual properties of zero-index metamaterials, which enable decoupling of the time and spatial field variations. This new class of resonators may inspire alternative design concepts, and it might lead to the first generation of deformable resonant devices.

  17. CRAB Cavity in CERN SPS

    International Nuclear Information System (INIS)

    Beam collisions with a crossing angle at the interaction point are often necessary in colliders to reduce the effects of parasitic collisions which induce emittance growth and decrease beam lifetime. The crossing angle reduces the geometrical overlap of the beams and hence the luminosity. Crab cavity offer a promising way to compensate the crossing angle and to realize effective head-on collisions. Moreover, the crab crossing mitigates the synchro-betatron resonances due to the crossing angle. A crab cavity experiment in SPS is proposed as a proof of principle before deciding on a full crab-cavity implementation in the LHC. In this paper, we investigate the effects of a single crab cavity on beam dynamics in the SPS and life time.

  18. LEP Radio Frequency Copper Cavities

    CERN Multimedia

    The pulse of a particle accelerator. 128 of these radio frequency cavities were positioned around CERN's 27-kilometre LEP ring to accelerate electrons and positrons. The acceleration was produced by microwave electric oscillations at 352 MHz. The electrons and positrons were grouped into bunches, like beads on a string, and the copper sphere at the top stored the microwave energy between the passage of individual bunches. This made for valuable energy savings as it reduced the heat generated in the cavity.

  19. Single and Coupled Nanobeam Cavities

    DEFF Research Database (Denmark)

    Ivinskaya, Aliaksandra; Lavrinenko, Andrei; Shyroki, Dzmitry M.; A. Sukhorukov, Andrey

    This book collects chapters on different theoretical and experimental aspects of photonics crystals for Nanophotonics applications. It is divided in two parts - a theoretical section and an experimental and applicative section. The first part includes chapters developing several numerical methods...... for analysis and design of photonic crystal devices, such as 2D ring resonators for filters, single and coupled nanobeam cavities, birefringence in photonic crystal cavities, threshold analysis in photonic crystal lasers, gap solitons in photonic crystals, novel photonic atolls, dynamic...

  20. RRR Characteristics for SRF Cavities

    OpenAIRE

    Jung, Yoochul; Hyun, Myungook; Joung, Mijoung

    2015-01-01

    The first heavy ion accelerator is being constructed by the rare isotope science project (RISP) launched by the Institute of Basic Science (IBS) in South Korea. Four different types of superconducting cavities were designed, and prototypes were fabricated such as a quarter wave resonator (QWR), a half wave resonator (HWR) and a single spoke resonator (SSR). One of the critical factors determining performances of the superconducting cavities is a residual resistance ratio (RRR). The RRR values...

  1. Analysis of Ge micro-cavities with in-plane tensile strains above 2%

    OpenAIRE

    Millar, R.W.; Gallacher, K.; Frigerio, J.; Ballabio, A; Bashir, A.; McLaren, I.; Isella, G.; Paul, D. J.

    2016-01-01

    Ge on Si micro-disk, ring and racetrack cavities are fabricated and strained using silicon nitride stressor layers. Photoluminescence measurements demonstrate emission at wavelengths ≥ 2.3 μm, and the highest strained samples demonstrate in-plane, tensile strains of > 2%, as measured by Raman spectroscopy. Strain analysis of the micro-disk structures demonstrate that shear strains are present in circular cavities, which can detrimentally effect the carrier concentration for direct band transi...

  2. Miniaturization of Airborne Integrated Cavity Output Spectroscopy Instrument Project

    Data.gov (United States)

    National Aeronautics and Space Administration — New measurement technologies are required to support science campaigns to better quantify rapid changes in the Earth atmosphere system. A key factor in this...

  3. Evaluation of MAX-DOAS aerosol retrievals by coincident observations using CRDS, lidar, and sky radiometer inTsukuba, Japan

    OpenAIRE

    Irie, H.; Nakayama, T.; Shimizu, A.; Yamazaki, A; Nagai, T; Uchiyama, A.; Y. Zaizen; Kagamitani, S.; Matsumi, Y.

    2015-01-01

    Coincident aerosol observations of multi-axis differential optical absorption spectroscopy (MAX-DOAS), cavity ring-down spectroscopy (CRDS), lidar, and sky radiometer were conducted in Tsukuba, Japan, on 5–18 October 2010. MAX-DOAS aerosol retrieval (for aerosol extinction coefficient and aerosol optical depth at 476 nm) was evaluated from the viewpoint of the need for a correction factor for oxygen collision complexes (O4 or O2–O2) absorption. The present study strongly sup...

  4. Evaluation of MAX-DOAS aerosol retrievals by coincident observations using CRDS, lidar, and sky radiometer in Tsukuba, Japan

    OpenAIRE

    Irie, H.; Nakayama, T.; Shimizu, A.; Yamazaki, A; Nagai, T; Uchiyama, A.; Y. Zaizen; Kagamitani, S.; Matsumi, Y.

    2015-01-01

    Coincident aerosol observations of Multi-Axis Differential Optical Absorption Spectroscopy (MAX-DOAS), Cavity Ring Down Spectroscopy (CRDS), lidar, and sky radiometer were conducted in Tsukuba, Japan on 5–18 October 2010. MAX-DOAS aerosol retrieval (for aerosol extinction coefficient and aerosol optical depth at 476 nm) was evaluated from the viewpoint of the need for a correction factor for oxygen collision complexes (O4 or O2-O2) absorption. The present study strongly supp...

  5. Technical Note: Using a high finesse optical resonator to provide a long light path for differential optical absorption spectroscopy: CE-DOAS

    OpenAIRE

    J. Meinen; J. Thieser; U. Platt; T. Leisner

    2010-01-01

    Cavity enhanced methods in absorption spectroscopy have seen a considerable increase in popularity during the past decade. Especially Cavity Enhanced Absorption Spectroscopy (CEAS) established itself in atmospheric trace gas detection by providing tens of kilometers of effective light path length using a cavity as short as 1 m. In this paper we report on the construction and testing of a compact and power efficient light emitting diode based broadband Cavity Enhanced Differential Optical Abso...

  6. Quarkonium spectroscopy

    International Nuclear Information System (INIS)

    Recent experimental investigations of heavy quark-antiquark bound state systems are reviewed. Results from SPEAR on charmonium spectroscopy and from DORIS and CESR on bottomonium spectroscopy are presented. The current status of the search for top is also discussed

  7. Analysis of mode-hop free tuning of folded cavity grating feedback lasers.

    Science.gov (United States)

    Yan, Jinyi; Gong, Qian; Gao, Jinjin; Cao, Chunfang; Wang, Yang; Xu, Haixin; Zhao, Wangpeng; Wang, Hailong

    2015-10-01

    We analytically study an external cavity laser structure including a folded cavity. A steering mirror is utilized in the folded cavity to deflect the intracavity laser beam. A mode-hop free tuning range of ∼400  GHz can be achieved by control of the steering mirror, and a fast tuning rate is expected because of the small mass of the steering mirror. This technique has potential for applications in spectroscopy for turbulent media, especially in the mid-infrared region. PMID:26479606

  8. TEM observations of crack tip: cavity interactions

    International Nuclear Information System (INIS)

    Crack tip-cavity interactions have been studied by performing room temperature deformation experiments in a transmission electron microscope on ion-irradiated type 316 stainless steel with small helium containing cavities. Slip dislocations emitted from a crack tip cut, sheared, and thereby elongated cavities without a volume enlargement. As the crack tip approached, a cavity volume enlargement occurred. Instead of the cavities continuing to enlarge until they touch, the walls between the cavities fractured. Fracture surface dimples do not correlate in size or density with these enlarged cavities

  9. Terahertz spectroscopy

    DEFF Research Database (Denmark)

    Jepsen, Peter Uhd

    2009-01-01

    In this presentation I will review methods for spectroscopy in the THz range, with special emphasis on the practical implementation of the technique known ad THz time-domain spectroscopy (THz-TDS). THz-TDS has revived the old field of far-infrared spectroscopy, and enabled a wealth of new...... activities that promise commercial potential for spectroscopic applications in the THz range. This will be illustrated with examples of spectroscopy of liquids inside their bottles as well as sensitive, quantitative spectroscopy in waveguides....

  10. Normal Conducting RF Cavity for MICE

    Energy Technology Data Exchange (ETDEWEB)

    Li, D.; DeMello, A.; Virostek, S.; Zisman, M.; Summers, D.

    2010-05-23

    Normal conducting RF cavities must be used for the cooling section of the international Muon Ionization Cooling Experiment (MICE), currently under construction at Rutherford Appleton Laboratory (RAL) in the UK. Eight 201-MHz cavities are needed for the MICE cooling section; fabrication of the first five cavities is complete. We report the cavity fabrication status including cavity design, fabrication techniques and preliminary low power RF measurements.

  11. Normal Conducting RF Cavity for MICE

    International Nuclear Information System (INIS)

    Normal conducting RF cavities must be used for the cooling section of the international Muon Ionization Cooling Experiment (MICE), currently under construction at Rutherford Appleton Laboratory (RAL) in the UK. Eight 201-MHz cavities are needed for the MICE cooling section; fabrication of the first five cavities is complete. We report the cavity fabrication status including cavity design, fabrication techniques and preliminary low power RF measurements.

  12. Cavity optomechanics and its applications

    Science.gov (United States)

    Bhattacharya, Mishkatul

    2009-05-01

    Cavity optomechanics is an emerging field at the intersection of quantum optics, atomic physics, nanoscience and gravitational wave interferometry. It involves cavities (with one or more mechanical degrees of freedom) driven by laser radiation. The ensuing optical control of macroscopic mechanical motion may have implications for precision sensing, coherent control of atoms and molecules, and quantum information processing. Due to recent innovations optomechanical physics has been realized in a variety of experimental systems spanning many orders of magnitude in mass and time-scales. In this talk, I will first introduce the basic paradigm of a laser-driven two mirror cavity used for cooling a vibrational mode. A three-mirror configuration recently implemented using a partially transmissive dielectric membrane in a high finesse cavity will then be discussed, and shown to be superior to the two-mirror design in a number of ways. One implication of the three-mirror configuration is the possibility of scaling optomechanical techniques to multiple oscillators. This topic will be explored by analysing the case of two membranes in a cavity where it will be shown that the collective(center-of-mass and breathing) modes of vibration can be cooled independently, analogous to a chain of trapped ions. Finally, future directions for possible applications to the control of atoms and molecules will be indicated briefly.

  13. Development of Side Coupled Cavities

    International Nuclear Information System (INIS)

    Side coupled Cavities are good candidates for proton accelerations in the 90-180 MeV range, as it has been first proposed for the CERN LINAC4 project. A side coupled Linac is made of a lump chain of resonant cavities, alternatively accelerating and coupling. A side coupled cavity has been designed in a CERN-LPSC collaboration to achieve LINAC4 requirements. After RF studies, a complete thermal study has been done, showing that 10-15% is the absolute maximum duty-cycle achievable by such a cavity. Error studies have been developed. They have shown that a tuning ring is mandatory and that a K equals 3% coupling factor is a good choice. A prototype has been built and each cell has been measured and tuned. A simple and accurate method has been used to get both the resonant frequency and the coupling factor, with a movable tuner and a linear fit. A similar method has been used to get the second order coupling factor. A large dispersion is observed on K. This is mainly due to the shape of the coupling apertures, which are very sensitive to mechanical errors. A future and realistic design must be very careful to guarantee a constant aperture (the important parameter is more the dispersion of k than its exact value). Finally, we analyse how to tune the cavity. This has to checked carefully and probably improved or corrected. Results are expected for mid-2008

  14. The ESS spoke cavity cryomodules

    Science.gov (United States)

    Bousson, Sebastien; Darve, Christine; Duthil, Patxi; Elias, Nuno; Molloy, Steve; Reynet, Denis; Thermeau, Jean-Pierre

    2014-01-01

    The European Spallation Source (ESS) is a multi-disciplinary research centre under design and construction in Lund, Sweden. This new facility is funded by a collaboration of 17 European countries and is expected to be up to 30 times brighter than today's leading facilities and neutron sources. The ESS will enable new opportunities for researchers in the fields of life sciences, energy, environmental technology, cultural heritage and fundamental physics. A 5 MW long pulse proton accelerator is used to reach this goal. The pulsed length is 2.86 ms, the repetition frequency is 14 Hz (4 % duty cycle), and the beam current is 62.5 mA. It is composed of one string of spoke cavity cryomodule and two strings of elliptical cavity cryomodules. This paper introduces the thermo-mechanical design and expected operation of the ESS spoke cavity cryomodules. These cryomodules contain two double spoke bulk Niobium cavities operating at 2 K and at a frequency of 352.21 MHz. The superconducting section of the Spoke Linac accelerates the beam from 90 MeV to 220 MeV. A Spoke Cavity Cryomodule Technology Demonstrator will be built and tested in order to validate the ESS series production.

  15. The ESS elliptical cavity cryomodules

    Science.gov (United States)

    Darve, Christine; Bosland, Pierre; Devanz, Guillaume; Olivier, Gilles; Renard, Bertrand; Thermeau, Jean-Pierre

    2014-01-01

    The European Spallation Source (ESS) is a multi-disciplinary research centre under design and construction in Lund, Sweden. This new facility is funded by a collaboration of 17 European countries and is expected to be up to 30 times brighter than today's leading facilities and neutron sources. The ESS will enable new opportunities for researchers in the fields of life sciences, energy, environmental technology, cultural heritage and fundamental physics. A 5 MW long pulse proton accelerator is used to reach this goal. The pulsed length is 2.86 ms, the repetition frequency is 14 Hz (4 % duty cycle), and the beam current is 62.5 mA. The superconducting section of the Linac accelerates the beam from 80 MeV to 2.0 GeV. It is composed of one string of spoke cavity cryomodule and two strings of elliptical cavity cryomodules. These cryomodules contain four elliptical Niobium cavities operating at 2 K and at a frequency of 704.42 MHz. This paper introduces the thermo-mechanical design, the prototyping and the expected operation of the ESS elliptical cavity cryomodules. An Elliptical Cavity Cryomodule Technology Demonstrator (ECCTD) will be built and tested in order to validate the ESS series production.

  16. Cavity as a source of conformational fluctuation and high-energy state: High-pressure NMR study of a cavity-enlarged mutant of T4 lysozyme

    CERN Document Server

    Maeno, Akihiro; Hirata, Fumio; Otten, Renee; Dahlquist, Frederick W; Yokoyama, Shigeyuki; Akasaka, Kazuyuki; Mulder, Frans A A; Kitahara, Ryo

    2014-01-01

    Although the structure, function, conformational dynamics, and controlled thermodynamics of proteins are manifested by their corresponding amino acid sequences, the natural rules for molecular design and their corresponding interplay remain obscure. In this study, we focused on the role of internal cavities of proteins in conformational dynamics. We investigated the pressure-induced responses from the cavity-enlarged L99A mutant of T4 lysozyme, using high-pressure NMR spectroscopy. The signal intensities of the methyl groups in the 1H/13C HSQC spectra, particularly those around the enlarged cavity, decreased with the increasing pressure, and disappeared at 200 MPa, without the appearance of new resonances, thus indicating the presence of heterogeneous conformations around the cavity within the ground state ensemble. Above 200 MPa, the signal intensities of more than 20 methyl groups gradually decreased with the increasing pressure, without the appearance of new resonances. Interestingly, these residues closel...

  17. A SURVEY OF CORONAL CAVITY DENSITY PROFILES

    International Nuclear Information System (INIS)

    Coronal cavities are common features of the solar corona that appear as darkened regions at the base of coronal helmet streamers in coronagraph images. Their darkened appearance indicates that they are regions of lowered density embedded within the comparatively higher density helmet streamer. Despite interfering projection effects of the surrounding helmet streamer (which we refer to as the cavity rim), Fuller et al. have shown that under certain conditions it is possible to use a Van de Hulst inversion of white-light polarized brightness (pB) data to calculate the electron density of both the cavity and cavity rim plasma. In this article, we apply minor modifications to the methods of Fuller et al. in order to improve the accuracy and versatility of the inversion process, and use the new methods to calculate density profiles for both the cavity and cavity rim in 24 cavity systems. We also examine trends in cavity morphology and how departures from the model geometry affect our density calculations. The density calculations reveal that in all 24 cases the cavity plasma has a flatter density profile than the plasma of the cavity rim, meaning that the cavity has a larger density depletion at low altitudes than it does at high altitudes. We find that the mean cavity density is over four times greater than that of a coronal hole at an altitude of 1.2 Rsun and that every cavity in the sample is over twice as dense as a coronal hole at this altitude. Furthermore, we find that different cavity systems near solar maximum span a greater range in density at 1.2 Rsun than do cavity systems near solar minimum, with a slight trend toward higher densities for systems nearer to solar maximum. Finally, we found no significant correlation of cavity density properties with cavity height-indeed, cavities show remarkably similar density depletions-except for the two smallest cavities that show significantly greater depletion.

  18. Phoxonic crystals and cavity optomechanics

    Science.gov (United States)

    Djafari-Rouhani, Bahram; El-Jallal, Said; Pennec, Yan

    2016-05-01

    Phoxonic crystals are dual phononic/photonic crystals exhibiting simultaneously band gaps for both types of excitations. Therefore, they have the ability to confine phonons and photons in the same cavity and in turn allow the enhancement of their interaction. In this paper, we review some of our theoretical works on cavity optomechanical interactions in different types of phoxonic crystals, including two-dimensional, slab, and nanobeam structures. Two mechanisms are behind the phonon-photon interaction, namely the photoelastic and the moving interface effects. Coupling rates of a few MHz are obtained with high-frequency phonons of a few GHz. Finally, we give some preliminary results about the optomechanical interaction when a metallic nanoparticle is introduced into the cavity, giving rise to coupled photon-plasmon modes or, in the case of very small particles, to an enhancement of the electric field at the position of the particle. xml:lang="fr"

  19. Crab cavities for the LHC

    International Nuclear Information System (INIS)

    For the high-luminosity LHC upgrade program (HL-LHC), the installation of crab cavities (CC) is essential to compensate the geometric luminosity loss due to the crossing angle and for luminosity leveling. One of the major challenges is the compatibility with machine protection in the regime of >500 MJ stored beam energy. Especially in a failure case (e.g. a CC quench or sparking in the coupler), the voltage and/or phase of a CC can change significantly with a fast time-constant of the order of a LHC-turn. This can lead to large, global betatron oscillations of the beam. The status of the LHC crab cavity upgrade program is presented and the influence of crab cavities on the beam dynamics is discussed. Necessary countermeasures to limit the impact of CC failures to an acceptable level are specified and operational scenarios that are compatible with machine protection considerations are proposed.

  20. RRR Characteristics for SRF cavities

    Science.gov (United States)

    Jung, Yoochul; Hyun, Myungook; Joung, Mijoung

    2015-10-01

    The first heavy ion accelerator is being constructed by the rare isotope science project (RISP) launched by the Institute of Basic Science (IBS) in South Korea. Four different types of superconducting cavities were designed, and prototypes such as a quarter-wave resonator (QWR), a half-wave resonator (HWR) and a single-spoke resonator (SSR) were fabricated. One of the critical factors determining the performances of superconducting cavities is the residual resistance ratio (RRR). The RRR values essentially represent how pure niobium is and how fast niobium can transmit heat. In general, the RRR degrades during electron beam welding due to impurity incorporation. Thus, it is important to maintain the RRR above a certain value at which a niobium cavity shows target performance. In this study, RRR degradation related with electron beam welding conditions, for example, the welding power, welding speed, and vacuum level, will be discussed.

  1. RRR Characteristics for SRF Cavities

    CERN Document Server

    Jung, Yoochul; Joung, Mijoung

    2015-01-01

    The first heavy ion accelerator is being constructed by the rare isotope science project (RISP) launched by the Institute of Basic Science (IBS) in South Korea. Four different types of superconducting cavities were designed, and prototypes were fabricated such as a quarter wave resonator (QWR), a half wave resonator (HWR) and a single spoke resonator (SSR). One of the critical factors determining performances of the superconducting cavities is a residual resistance ratio (RRR). The RRR values essentially represent how much niobium is pure and how fast niobium can transmit heat as well. In general, the RRR degrades during electron beam welding due to the impurity incorporation. Thus it is important to maintain RRR above a certain value at which a niobium cavity shows target performance. In this study, RRR degradation related with electron beam welding conditions, for example, welding power, welding speed, and vacuum level will be discussed.

  2. Broadband Rotational Spectroscopy

    Science.gov (United States)

    Pate, Brooks

    2014-06-01

    The past decade has seen several major technology advances in electronics operating at microwave frequencies making it possible to develop a new generation of spectrometers for molecular rotational spectroscopy. High-speed digital electronics, both arbitrary waveform generators and digitizers, continue on a Moore's Law-like development cycle that started around 1993 with device bandwidth doubling about every 36 months. These enabling technologies were the key to designing chirped-pulse Fourier transform microwave (CP-FTMW) spectrometers which offer significant sensitivity enhancements for broadband spectrum acquisition in molecular rotational spectroscopy. A special feature of the chirped-pulse spectrometer design is that it is easily implemented at low frequency (below 8 GHz) where Balle-Flygare type spectrometers with Fabry-Perot cavity designs become technologically challenging due to the mirror size requirements. The capabilities of CP-FTMW spectrometers for studies of molecular structure will be illustrated by the collaborative research effort we have been a part of to determine the structures of water clusters - a project which has identified clusters up to the pentadecamer. A second technology trend that impacts molecular rotational spectroscopy is the development of high power, solid state sources in the mm-wave/THz regions. Results from the field of mm-wave chirped-pulse Fourier transform spectroscopy will be described with an emphasis on new problems in chemical dynamics and analytical chemistry that these methods can tackle. The third (and potentially most important) technological trend is the reduction of microwave components to chip level using monolithic microwave integrated circuits (MMIC) - a technology driven by an enormous mass market in communications. Some recent advances in rotational spectrometer designs that incorporate low-cost components will be highlighted. The challenge to the high-resolution spectroscopy community - as posed by Frank De

  3. Dual-cavity basket promotes encapsulation in water in an allosteric fashion.

    Science.gov (United States)

    Chen, Shigui; Yamasaki, Makoto; Polen, Shane; Gallucci, Judith; Hadad, Christopher M; Badjić, Jovica D

    2015-09-30

    We prepared dual-cavity basket 1 to carry six (S)-alanine residues at the entrance of its two juxtaposed cavities (289 Å(3)). With the assistance of (1)H NMR spectroscopy and calorimetry, we found that 1 could trap a single molecule of 4 (K1 = 1.45 ± 0.40 × 10(4) M(-1), ITC), akin in size (241 Å(3)) and polar characteristics to nerve agent VX (289 Å(3)). The results of density functional theory calculations (DFT, M06-2X/6-31G*) and experiments ((1)H NMR spectroscopy) suggest that the negative homotropic allosterism arises from the guest forming C-H···π contacts with all three of the aromatic walls of the occupied basket's cavity. In response, the other cavity increases its size and turns rigid to prevent the formation of the ternary complex. A smaller guest 6 (180 Å(3)), akin in size and polar characteristics to soman (186 Å(3)), was also found to bind to dual-cavity 1, although giving both binary [1⊂6] and ternary [1⊂62] complexes (K1 = 7910 M(-1) and K2 = 2374 M(-1), (1)H NMR spectroscopy). In this case, the computational and experimental ((1)H NMR spectroscopy) results suggest that only two aromatic walls of the occupied basket's cavity form C-H···π contacts with the guest to render the singly occupied host flexible enough to undergo additional structural changes necessary for receiving another guest molecule. The structural adaptivity of dual-cavity baskets of type 1 is unique and important for designing multivalent hosts capable of effectively sequestering targeted guests in an allosteric manner to give stable supramolecular polymers. PMID:26348904

  4. Cavity Solitons in VCSEL Devices

    Directory of Open Access Journals (Sweden)

    S. Barbay

    2011-01-01

    Full Text Available We review advances on the experimental study of cavity solitons in VCSELs in the past decade. We emphasize on the design and fabrication of electrically or optically pumped broad-area VCSELs used for CSs formation and review different experimental configurations. Potential applications of CSs in the field of photonics are discussed, in particular the use of CSs for all-optical processing of information and for VCSELs characterization. Prospects on self-localization studies based on vertical cavity devices involving new physical mechanisms are also given.

  5. Radiography of the abdominal cavity

    International Nuclear Information System (INIS)

    Radiography is a very important part of the diagnostic procedure in many small animal diseases. Technically perfect X-rays are essential for the exact diagnosis. The general appearance of the abdominal cavity should be evaluated at first, e.g. the overall contrast and the definition of the visualized organs. Then particular attention should be paid, if there is any peritoneal effusion or free air in the peritoneal cavity. Subsequently each radiographically visible organ has to be evaluated for its position, size, shape and radiographic density

  6. Nanobeam Cavities for Reconfigurable Photonics

    OpenAIRE

    Deotare, Parag

    2012-01-01

    We investigate the design, fabrication, and experimental characterization of high quality factor photonic crystal nanobeam cavities, with theoretical quality factors of \\(1.4 × 10^7\\) in silicon, operating at ~1550 nm. By detecting the cross-polarized resonantly scattered light from a normally incident laser beam, we measure a quality factor of nearly \\(7.5 × 10^5\\). We show on-chip integration of the cavities using waveguides and an inverse taper geometry based mode size converters, and also...

  7. Synchronization in an optomechanical cavity.

    Science.gov (United States)

    Shlomi, Keren; Yuvaraj, D; Baskin, Ilya; Suchoi, Oren; Winik, Roni; Buks, Eyal

    2015-03-01

    We study self-excited oscillations (SEO) in an on-fiber optomechanical cavity. Synchronization is observed when the optical power that is injected into the cavity is periodically modulated. A theoretical analysis based on the Fokker-Planck equation evaluates the expected phase space distribution (PSD) of the self-oscillating mechanical resonator. A tomography technique is employed for extracting PSD from the measured reflected optical power. Time-resolved state tomography measurements are performed to study phase diffusion and phase locking of the SEO. The detuning region inside which synchronization occurs is experimentally determined and the results are compared with the theoretical prediction. PMID:25871175

  8. Sterility of the uterine cavity

    DEFF Research Database (Denmark)

    Møller, Birger R.; Kristiansen, Frank V.; Thorsen, Poul;

    1995-01-01

    In a prospective open study the sterility of the uterine cavity was evaluated in 99 women admitted for hysterectomy. The indications for hysterectomy were in most cases persistent irregular vaginal bleeding and fibromyomas of the uterus. Samples for both aerobic and anaerobic bacteria, Chlamydia...... trachomatis, yeasts and viruses were taken preoperatively from the apex of the vagina and cervical os. Immediately after hysterectomy the uterus was opened under sterile conditions and samples obtained from the isthmus and fundus of the uterine cavity for microbiological examination. Wet smears were taken...

  9. Cavity-Enhanced Immunoassay Measurements in Microtiter Plates Using BBCEAS.

    Science.gov (United States)

    Bajuszova, Zuzana; Ali, Zulfiqur; Scott, Simon; Seetohul, L Nitin; Islam, Meez

    2016-05-17

    We report on the first detailed use of broadband cavity enhanced absorption spectroscopy (BBCEAS) as a detection system for immunoassay. A vertical R ≥ 0.99 optical cavity was integrated with a motorized XY stage, which functioned as a receptacle for 96-well microtiter plates. The custom-built cavity enhanced microplate reader was used to make measurements on a commercially available osteocalcin sandwich ELISA kit. A 30-fold increase in path length was obtained with a minimum detectable change in the absorption coefficient, αmin(t), of 5.3 × 10(-5) cm(-1) Hz(-1/2). This corresponded to a 39-fold increase in the sensitivity of measurement when directly compared to measurements in a conventional microplate reader. Separate measurements of a standard STREP-HRP colorimetric reaction in microtiter plates of differing optical quality produced an increase in sensitivity of up to 115-fold compared to a conventional microplate reader. The sensitivity of the developed setup compared favorably with previous liquid-phase cavity enhanced studies and approaches the sensitivity of typical fluorometric ELISAs. It could benefit any biochemical test which uses single pass absorption as a detection method, through either the label free detection of biologically important molecules at lower concentrations or the reduction in the amount of expensive biochemicals needed for a particular test, leading to cheaper tests. PMID:27089516

  10. Field emission in RF cavities

    International Nuclear Information System (INIS)

    Electron field emission limits the accelerating gradient in superconducting cavities. It is shown how and why it is an important problem. The phenomenology of field emission is then described, both in DC and RF regimes. Merits of a few plausible 'remedies' to field emission are discussed. (author)

  11. Nasal cavity and frontal sinuses

    International Nuclear Information System (INIS)

    The anatomy, diagnostic principles, and surgical techniques relating to the nasal cavity and frontal sinuses are reviewed. Disorders are considered under headings of infectious, neoplastic, and miscellaneous conditions. For each disease condition, an attempt is made to emphasize particular problems and discuss new developments on treatment. Specific recommendations have been made where possible, along with the expected outcome

  12. Hybrid Vertical-Cavity Laser

    DEFF Research Database (Denmark)

    2010-01-01

    The present invention provides a light source (2) for light circuits on a silicon platform (3). A vertical laser cavity is formed by a gain region (101) arranged between a top mirror (4) and a bottom grating-mirror (12) in a grating region (11) in a silicon layer (10) on a substrate. A waveguide...

  13. Hydrofracture from a growing cavity

    International Nuclear Information System (INIS)

    The Los Alamos KRAK code has been used to calculate fracturing away from the growing cavity formed by a nuclear detonation. In the 55 ms before rebound, the stress in the surrounding rock is decreasing, and conditions for fracture propagation are good. During this interval, hydrofractures driven by the high-temperature, high-pressure gases within the cavity grow readily. Fracture growth slows when the stress increases as the residual hoop is formed during rebound. However, cracks are found to escape through the residual stress field. The effects of initial conditions and zoning on the numerical calculations are discussed, and the roles of the media saturation and roughness are briefly considered. The largest uncertainty in these calculations is the manner in which the effective pressure used in computing crack widths is extended into the cavity region. Because the present calculations have been done using a very conservative scheme, actual fractures should grow even more readily. We conclude that hydrofracture is an important, if not dominant, process in transporting mass and energy out of a cavity formed by a nuclear detonation

  14. Cavity length below chute aerators

    Institute of Scientific and Technical Information of China (English)

    WU JianHua; RUAN ShiPing

    2008-01-01

    It is proved that air entrainment is one of the efficient measures dealing with cavitation control for the release works of hydropower projects. There are many factors to be considered in designing a chute aerator. One of the most important factors concerns the cavity length below the aerator, which has outstanding effects on air entrainment against cavitation damage. It is crucial to determine reasonable emergence angle for the calculation of the cavity length. In the present paper the overall effects of structural and hydraulic parameters on the emergence angle of the flow from the aerator were analyzed. Four improved expressions of the emergence angle with weight coefficient were investigated through experimental data of 68 points observed from 12 aerators of 6 hydropower projects, of both model and prototype, on the basis of error theory. A method to calculate the cavity length below aerators was suggested, which considers overall effects of the above mentioned parameters. Comparison between the method in this paper and the other five methods of calculating the cavity length showed that the present method is much more reliable than the existing methods while the mean error of the method is less than others.

  15. Cavity length below chute aerators

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    It is proved that air entrainment is one of the efficient measures dealing with cavi-tation control for the release works of hydropower projects. There are many factors to be considered in designing a chute aerator. One of the most important factors concerns the cavity length below the aerator,which has outstanding effects on air entrainment against cavitation damage. It is crucial to determine reasonable emergence angle for the calculation of the cavity length. In the present paper the overall effects of structural and hydraulic parameters on the emergence angle of the flow from the aerator were analyzed. Four improved expressions of the emer-gence angle with weight coefficient were investigated through experimental data of 68 points observed from 12 aerators of 6 hydropower projects,of both model and prototype,on the basis of error theory. A method to calculate the cavity length be-low aerators was suggested,which considers overall effects of the above men-tioned parameters. Comparison between the method in this paper and the other five methods of calculating the cavity length showed that the present method is much more reliable than the existing methods while the mean error of the method is less than others.

  16. Large-mode enhancement cavities.

    Science.gov (United States)

    Carstens, Henning; Holzberger, Simon; Kaster, Jan; Weitenberg, Johannes; Pervak, Volodymyr; Apolonski, Alexander; Fill, Ernst; Krausz, Ferenc; Pupeza, Ioachim

    2013-05-01

    In passive enhancement cavities the achievable power level is limited by mirror damage. Here, we address the design of robust optical resonators with large spot sizes on all mirrors, a measure that promises to mitigate this limitation by decreasing both the intensity and the thermal gradient on the mirror surfaces. We introduce a misalignment sensitivity metric to evaluate the robustness of resonator designs. We identify the standard bow-tie resonator operated close to the inner stability edge as the most robust large-mode cavity and implement this cavity with two spherical mirrors with 600 mm radius of curvature, two plane mirrors and a round trip length of 1.2 m, demonstrating a stable power enhancement of near-infrared laser light by a factor of 2000. Beam radii of 5.7 mm × 2.6 mm (sagittal × tangential 1/e(2) intensity radius) on all mirrors are obtained. We propose a simple all-reflective ellipticity compensation scheme. This will enable a significant increase of the attainable power and intensity levels in enhancement cavities. PMID:23670017

  17. A 200 MHz prebunching cavity

    CERN Multimedia

    1977-01-01

    This cavity was installed in the PS ring and proved very efficient in providing a modulation on the PS beam before it is injected into the SPS machine. Moreover it allowed longitudinal instabilities studies at high intensities. Roberto Cappi stands on the left.

  18. Nanobeam cavities for Reconfigurable Photonics

    Science.gov (United States)

    Deotare, Parag B.

    We investigate the design, fabrication, and experimental characterization of high quality factor photonic crystal nanobeam cavities, with theoretical quality factors of 1.4 x 107 in silicon, operating at ˜ 1550 nm. By detecting the cross-polarized resonantly scattered light from a normally incident laser beam, we measure a quality factor of nearly 7.5 x 105. We show on-chip integration of the cavities using waveguides and an inverse taper geometry based mode size converters, and also demonstrate tuning of the optical resonance using thermo-optic effect. We also study coupled cavities and show that the single nanobeam cavity modes are coupled into even and odd superposition modes. Using electrostatic force and taking advantage of the highly dispersive nature of the even mode to the nanobeam separation, we demonstrate dynamically reconfigurable optical filters tunable continuously and reversibly over a 9.5 nm wavelength range. The electrostatic force, obtained by applying bias voltages directly to the nanobeams, is used to control the spacing between the nanobeams, which in turn results in tuning of the cavity resonance. The observed tuning trends were confirmed through simulations that modeled the electrostatic actuation as well as the optical resonances in our reconfigurable geometries. Finally we demonstrate reconfiguration of coupled cavities by using optical gradient force induced mechanical actuation. Propagating waveguide modes that exist over wide wavelength range are used to actuate the structures and in that way control the resonance of a localized cavity mode. Using this all-optical approach, more than 18 linewidths of tuning range is demonstrated. Using an on-chip temperature self-referencing method that we developed, we determined that 20% of the total tuning was due to optomechanical reconfiguration and the rest due to thermo-optic effects. By operating the device at frequencies higher than the thermal cut-off, we show high speed operation dominated by

  19. Surface analyses of electropolished niobium samples for superconducting radio frequency cavity

    International Nuclear Information System (INIS)

    The performance of superconducting radio frequency niobium cavities is sometimes limited by contaminations present on the cavity surface. In the recent years extensive research has been done to enhance the cavity performance by applying improved surface treatments such as mechanical grinding, electropolishing (EP), chemical polishing, tumbling, etc., followed by various rinsing methods such as ultrasonic pure water rinse, alcoholic rinse, high pressure water rinse, hydrogen per oxide rinse, etc. Although good cavity performance has been obtained lately by various post-EP cleaning methods, the detailed nature about the surface contaminants is still not fully characterized. Further efforts in this area are desired. Prior x-ray photoelectron spectroscopy (XPS) analyses of EPed niobium samples treated with fresh EP acid, demonstrated that the surfaces were covered mainly with the niobium oxide (Nb2O5) along with carbon, in addition a small quantity of sulfur and fluorine were also found in secondary ion mass spectroscopy (SIMS) analysis. In this article, the authors present the analyses of surface contaminations for a series of EPed niobium samples located at various positions of a single cell niobium cavity followed by ultrapure water rinsing as well as our endeavor to understand the aging effect of EP acid solution in terms of contaminations presence at the inner surface of the cavity with the help of surface analytical tools such as XPS, SIMS, and scanning electron microscope at KEK.

  20. Chemical spectroscopy

    International Nuclear Information System (INIS)

    The purpose of chemical spectroscopy with neutrons is to utilize the dependence of neutron scattering cross-sections on isotope and on momentum transfer (which probes the spatial extent of the excitation) to understand fundamental and applied aspects of the dynamics of molecules and fluids. Chemical spectroscopy is divided into three energy ranges: vibrational spectroscopy, 25-500 MeV, for which much of the work is done on Be-filter analyzer instruments; low energy spectroscopy, less than 25 MeV; and high resolution spectroscopy, less than 1 MeV, which typically is performed on backscattering spectrometers. Representative examples of measurements of the Q-depenence of vibrational spectra, higher energy resolution as well as extension of the Q-range to lower values at high energy transfers, and provisions of higher sensitivities in vibrational spectroscopy are discussed. High resolution, high sensitivity, and polarization analysis studies in low energy spectroscopy are discussed. Applications of very high resolution spectroscopy are also discussed

  1. Generating photon pulses with an oscillating cavity

    OpenAIRE

    Lambrecht, A.(Laboratoire Kastler-Brossel, CNRS, ENS, Collège de France, UPMC, Campus Jussieu, 75252 Paris, France); Jaekel, M. T.; Reynaud, S

    1998-01-01

    We study the generation of photon pulses from thermal field fluctuations through opto-mechanical coupling to a cavity with an oscillatory motion. Pulses are regularly spaced and become sharp for a high finesse cavity.

  2. Coupled Photonic Crystal Cavity Array Laser

    DEFF Research Database (Denmark)

    Schubert, Martin

    quantum dots are carried out. In agreement with a simple gain model the structures do not show stimulated emission. The spectral splitting due to the coupling between single cavities as well as arrays of cavities is studied theoretically and experimentally. Lasing is observed for photonic crystal cavity......This thesis describes the design, fabrication and characterization of photonic crystal slab lasers. The main focus is on coupled photonic crystal cavity lasers which are examined in great detail. The cavity type which is mainly explored consists of a defect formed by a single missing hole in the...... structures with quantum wells. A detailed Analysis is conducted on single cavities, two coupled cavities and arrays of coupled cavities. The lasing threshold is determined by measuring the photoluminescence intensity depending on the excitation power. Changes in the linewidth and peak position for different...

  3. Operational experience with crab cavities at KEKB

    OpenAIRE

    Funakoshi, Y.; Group, for the KEKB Commissioning

    2014-01-01

    KEKB was in operation from December 1988 to June 2010. The crab cavities were installed at KEKB in February 2007 and worked very stably until the end of KEKB operation. Operational experience of the crab cavities with beams is described.

  4. Stages of Lip and Oral Cavity Cancer

    Science.gov (United States)

    ... common treatment for all stages of lip and oral cavity cancer. Surgery may include the following: Wide local excision : Removal ... cancer may have spread from the lip and oral cavity. Plastic surgery : An operation that restores or improves the appearance ...

  5. What Are Oral Cavity and Oropharyngeal Cancers?

    Science.gov (United States)

    ... Research Get Involved Find Local ACS Learn About Cancer » Oral Cavity and Oropharyngeal Cancer » Detailed Guide » What are ... how cancers start and spread, see What Is Cancer? Oral cavity cancer, or just oral cancer, is cancer ...

  6. Magnetosheath cavities: case studies using Cluster observations

    OpenAIRE

    Katırcıoğlu, F. T.; Z. Kaymaz; D. G. Sibeck; Dandouras, I.

    2009-01-01

    This paper presents examples of magnetosheath cavities in Cluster spacecraft observations. The cavities are accompanied by high energy particles in the magnetosheath and characterized by depressed magnetic fields and densities. Flow speeds decrease and temperatures increase within the cavities. All magnetosheath parameters show increased variability within the cavities when the energetic particle flux is high. We predict outward motion of the magnetopause boundary in respons...

  7. Parametric resonance in tunable superconducting cavities

    OpenAIRE

    Wustmann, Waltraut; Shumeiko, Vitaly

    2013-01-01

    We develop a theory of parametric resonance in tunable superconducting cavities. The nonlinearity introduced by the superconducting quantum interference device (SQUID) attached to the cavity and damping due to connection of the cavity to a transmission line are taken into consideration. We study in detail the nonlinear classical dynamics of the cavity field below and above the parametric threshold for the degenerate parametric resonance, featuring regimes of multistability and parametric radi...

  8. Prototype storage cavity for LEP accelerating RF

    CERN Multimedia

    1980-01-01

    The principle of an RF storage cavity was demonstrated with this prototype, working at 500 MHz. Ian Wilso seems to hold it in his hands. The storage cavities had 4 portholes, 1 each for: RF feed; tuning; connection to the accelerating cavity; vacuum pump. The final storage cavities were larger, to suit the lower LEP accelerating frequency of 352.2 MHz. See also 8002294, 8006510X, 8109346, 8407619X, and Annual Report 1980, p.115.

  9. Theory and technology for superconducting cavities

    CERN Document Server

    Lengeler, Herbert

    1993-01-01

    The course will address Physicist and Engineers who are newcomers in the field of accelerators and accelerating cavities. The elements of RF-Superconductivity will be presented with special relevance to accelerating cavities. The present ststus of achievable accelerating fields and RF losses will be given and their link to the special technologies for cavity fabrication and surface treatments will be stressed. Cavity auxiliaries like main couplers, higher order mode couplers and frequency tuners will be described.

  10. Cavity QED experiments with ion Coulomb crystals

    DEFF Research Database (Denmark)

    Herskind, Peter Fønss; Dantan, Aurélien; Marler, Joan; Albert, Magnus; Drewsen, Michael

    Cavity QED experimental results demonstrating collective strong coupling between ensembles of atomic ions cooled into Coulomb crystals and optical cavity fields have been achieved. Collective Zeeman coherence times of milliseconds have furthermore been obtained.......Cavity QED experimental results demonstrating collective strong coupling between ensembles of atomic ions cooled into Coulomb crystals and optical cavity fields have been achieved. Collective Zeeman coherence times of milliseconds have furthermore been obtained....

  11. Cavity-water interface is polar

    OpenAIRE

    Friesen, Allan D.; Matyushov, Dmitry V.

    2010-01-01

    We present the results of numerical simulations of the electrostatics and dynamics of water hydration shells surrounding Kihara cavities given by a Lennard-Jones (LJ) layer at the surface of a hard-sphere cavity. The local dielectric response of the hydration layer substantially exceeds that of bulk water, with the magnitude of the dielectric constant peak in the shell increasing with the growing cavity size. The polar shell propagates into bulk water to approximately the cavity radius. The s...

  12. Intracavity Sensing via Compliance Voltage in an External Cavity Quantum Cascade Laser

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, Mark C.; Taubman, Matthew S.

    2012-07-01

    We demonstrate a technique for gas phase spectroscopy and sensing by detecting changes in compliance voltage of an external cavity quantum cascade laser due to intracavity absorption. The technique is characterized and used to measure the absorption spectrum of water vapor and Freon-134a.

  13. CLASSIFYING NODULAR LESIONS OF ORAL CAVITY

    OpenAIRE

    Sumit Bhateja

    2013-01-01

    Diagnosis of many lesions of the oral cavity is challenging to most cliniciansbecause of their uncommon prevalence. A number of cystic, osteodystrophic,microbial, tumor and tumor like lesions of the oral cavity are present withcharacteristic exophytic/raised surface; which makes their diagnosis and studysimpler. The present article is attempted at classifying the common nodular lesions ofthe oral cavity.

  14. Nanometer cavities studied by positron annihilation

    International Nuclear Information System (INIS)

    Positronium (Ps) is trapped in cavities in insulating solids, and the lifetime of ortho Ps is determined by the size of the cavity. The information on the properties of the cavities obtained by use of the standard slow positron beam and the 'normal' positron annihilation techniques is compared for several selected cases. (author)

  15. Computer codes for RF cavity design

    International Nuclear Information System (INIS)

    In RF cavity design, numerical modeling is assuming an increasingly important role with the help of sophisticated computer codes and powerful yet affordable computers. A description of the cavity codes in use in the accelerator community has been given previously. The present paper will address the latest developments and discuss their applications to cavity tuning and matching problems. (Author) 8 refs., 10 figs

  16. Computer codes for RF cavity design

    International Nuclear Information System (INIS)

    In RF cavity design, numerical modeling is assuming an increasingly important role with the help of sophisticated computer codes and powerful yet affordable computers. A description of the cavity codes in use in the accelerator community has been given previously. The present paper will address the latest developments and discuss their applications to cavity toning and matching problems

  17. Diffusion stabilizes cavity solitons in bidirectional lasers

    OpenAIRE

    Perez-Arjona, Isabel; Sanchez-Morcillo, Victor; Redondo, Javier; Staliunas, Kestutis; Roldan, Eugenio

    2009-01-01

    We study the influence of field diffusion on the spatial localized structures (cavity solitons) recently predicted in bidirectional lasers. We find twofold positive role of the diffusion: 1) it increases the stability range of the individual (isolated) solitons; 2) it reduces the long-range interaction between the cavity solitons. Latter allows the independent manipulation (writing and erasing) of individual cavity solitons.

  18. Power coupler for the ILC crab cavity

    Energy Technology Data Exchange (ETDEWEB)

    Burt, G.; Dexter, A.; Jenkins, R.; /Lancaster U.; Beard, C.; Goudket, P.; McIntosh, P.A.; /Daresbury; Bellantoni, Leo; /Fermilab

    2007-06-01

    The ILC crab cavity will require the design of an appropriate power coupler. The beam-loading in dipole mode cavities is considerably more variable than accelerating cavities, hence simulations have been performed to establish the required external Q. Simulations of a suitable coupler were then performed and were verified using a normal conducting prototype with variable coupler tips.

  19. Cavity-less on-chip optomechanics using excitonic transitions in semiconductor heterostructures

    Science.gov (United States)

    Okamoto, Hajime; Watanabe, Takayuki; Ohta, Ryuichi; Onomitsu, Koji; Gotoh, Hideki; Sogawa, Tetsuomi; Yamaguchi, Hiroshi

    2015-10-01

    The hybridization of semiconductor optoelectronic devices and nanomechanical resonators provides a new class of optomechanical systems in which mechanical motion can be coupled to light without any optical cavities. Such cavity-less optomechanical systems interconnect photons, phonons and electrons (holes) in a highly integrable platform, opening up the development of functional integrated nanomechanical devices. Here we report on a semiconductor modulation-doped heterostructure-cantilever hybrid system, which realizes efficient cavity-less optomechanical transduction through excitons. The opto-piezoelectric backaction from the bound electron-hole pairs enables us to probe excitonic transition simply with a sub-nanowatt power of light, realizing high-sensitivity optomechanical spectroscopy. Detuning the photon energy from the exciton resonance results in self-feedback cooling and amplification of the thermomechanical motion. This cavity-less on-chip coupling enables highly tunable and addressable control of nanomechanical resonators, allowing high-speed programmable manipulation of nanomechanical devices and sensor arrays.

  20. Investigation of carrier to envelope phase and repetition rate: fingerprints of mode-locked laser cavities

    International Nuclear Information System (INIS)

    We use mode locked lasers in a non-conventional way, as a sensor to perform intracavity measurements. To understand this new technique of intracavity phase interferometry (IPI), one should take a detailed look at the characteristics of the frequency comb and its sensitivity to its parent cavity. The laser cavity provides a means to perform phase interferometry while outside the cavity one can only observe amplitude interference. Many physical quantities such as nonlinear index, Earth rotation, magnetic field, Fresnel drag, etc are converted to phase. IPI is performed by designing laser cavities in which two pulses circulate independently, generating two pulse trains that can have a phase difference that will be converted to frequency. We also explore repetition rate spectroscopy in Rb87 by tailoring a laser wavelength, power and bandwidth. Coherent population trapping is observed when the laser repetition rate matches submultiples of hyperfine splitting. (phd tutorial)

  1. MR spectroscopy

    International Nuclear Information System (INIS)

    MR has had a major impact on medicine over the past few years due to rapid advances in the application of the MR phenomena. The result has been a valuable new imaging modality. In the near future, MR spectroscopy will likely have an even greater impact on the practice of medicine. This is due to the ability of MR spectroscopy to provide a nondestructive and noninvasive means of monitoring body chemistry in humans. For example, P-31 MR spectroscopy can be used to monitor pH and metabolites involved in both bioenergetics and lipid metabolism. The results from pioneering studies in animals and humans provide evidence that P-31 MR spectroscopy will both contribute to the understanding of disease processes and provide a monitor of therapeutic response. Thus, MR spectroscopy promises to provide a new window of information to clinicians for use in the management of human diseases. In this refresher course, an introduction to MR spectroscopy methodology and the information contained in the MR spectrum is presented. In addition, an overview of areas in which MR spectroscopy may have a major impact on medicine is presented

  2. Laser spectroscopy

    CERN Document Server

    Demtröder, Wolfgang

    Keeping abreast of the latest techniques and applications, this new edition of the standard reference and graduate text on laser spectroscopy has been completely revised and expanded. While the general concept is unchanged, the new edition features a broad array of new material, e.g., ultrafast lasers (atto- and femto-second lasers) and parametric oscillators, coherent matter waves, Doppler-free Fourier spectroscopy with optical frequency combs, interference spectroscopy, quantum optics, the interferometric detection of gravitational waves and still more applications in chemical analysis, medical diagnostics, and engineering.

  3. Fullerene photoemission time delay explores molecular cavity in attoseconds

    CERN Document Server

    Magrakvelidze, Maia; Dixit, Gopal; Madjet, Mohamed El-Amine; Chakraborty, Himadri S

    2014-01-01

    Time-resolved photoelectron spectroscopy can probe interference oscillations in C60 valence emissions that produce series of minima whose energy separation depends on the molecular size. We show that the quantum phase associated with these minima exhibits rapid variations due to electron correlations, causing rich structures in the photoemission time delay. These findings provide a way to utilize temporal information to access the fullerene cavity size, that is making the time to "see" the space, and can be generalized to photoemissions from clusters and nanostructures.

  4. Photoluminescence microscopy on air-suspended carbon nanotubes coupled to photonic crystal nanobeam cavities

    Science.gov (United States)

    Miura, R.; Imamura, S.; Shimada, T.; Ohta, R.; Iwamoto, S.; Arakawa, Y.; Kato, Y. K.

    2014-03-01

    Because carbon nanotubes are room-temperature telecom-band emitters and can be grown on silicon substrates, they are ideal for coupling to silicon photonic cavities.[2,3 In particular, as-grown air-suspended carbon nanotubes show excellent optical properties, but cavity modes with large fields in the air are needed in order to achieve efficient coupling. Here we investigate individual air-suspended nanotubes coupled to photonic crystal nanobeam cavities. We utilize cavities that confine air-band modes which have large fields in the air. Dielectric mode cavities are also prepared for comparison. We fabricate the devices from silicon-on-insulator substrates by using electron beam lithography and dry etching to form the nanobeam structure. The buried oxide layer is removed by wet etching, and carbon nanotubes are grown onto the cavities by chemical vapor deposition. We perform photoluminescence imaging and excitation spectroscopy to find the positions of the nanotubes and identify their chiralities. For both types of devices, cavity modes with quality factors of ~3000 are observed within the nanotube emission peak. Work supported by SCOPE, KAKENHI, The Telecommunications Advancement Foundation, The Toyota Physical and Chemical Research Institute, Project for Developing Innovation Systems of MEXT, Japan and the Photon Frontier Network Program of MEXT, Japan.

  5. Non-reacting flow visualization of supersonic combustor based on cavity and cavity-strut flameholder

    Science.gov (United States)

    Zhao, Yanhui; Liang, Jianhan; Zhao, Yuxin

    2016-04-01

    Nano-particle planer laser scattering and particle image velocimetry technology are employed to observe the flow field of scramjet combustors based on cavity and cavity-strut flameholder. Density field and velocity distribution inside combustors are obtained. Mainstream fluid enters into cavity nearby side wall in experimental observation because side wall shock waves interact with bottom wall boundary layer. Cavity fluid is entrained into mainstream in the middle of combustor meanwhile. Flow past cavity displays obvious three dimensional characteristics in both combustors. But cavity-strut combustor displays asymmetrical flow field because of strut configuration. Mass exchange between mainstream and cavity fluid is evaluated by statistic mass flow rate into cavity. Mass flow rate near side wall is raised to 6.62 times of the value in the middle of cavity combustor while it is 5.1 times in cavity-strut combustor. Further study is needed to injection strategies and realistic flow characteristics on condition of combustion.

  6. Status of the ILC Crab Cavity Development

    International Nuclear Information System (INIS)

    The International Linear Collider (ILC) will require two dipole cavities to 'crab' the electron and positron bunches prior to their collision. It is proposed to use two 9 cell SCRF dipole cavities operating at a frequency of 3.9 GHz, with a transverse gradient of 3.8MV/m in order to provide the required transverse kick. Extensive numerical modelling of this cavity and its couplers has been performed. Aluminium prototypes have been manufactured and tested to measure the RF properties of the cavity and couplers. In addition single cell niobium prototypes have been manufactured and tested in a vertical cryostat. The International Collider (ILC) (1) collides bunches of electrons and positrons at a crossing angle of 14 mrad. The angle between these bunches causes a loss in luminosity due to geometric effects (2). The luminosity lost from this geometric effect can be recovered by rotating the bunches into alignment prior to collision. One possible method of rotating the bunches is to use a crab cavity (3). A crab cavity is a transverse defecting cavity, where the phase of the cavity is such that the head and tail of the bunch receive equal and opposite kicks. As the bunches are only 500 nm wide in the horizontal plane, the cavity phase must be strictly controlled to avoid the bunch centre being deflected too much. In order to keep the phase stability within the required limits it is required that the cavity be superconducting to avoid thermal effects in both the cavity and its RF source. At the location of the crab cavity in the ILC there is only 23 cm separation between the centre of the cavity and the extraction line, hence the cavity must be small enough to fit in this space. This, along with the difficulty of making high frequency SRF components, set the frequency of the cavity to 3.9 GHz.

  7. Status of the ILC Crab Cavity Development

    Energy Technology Data Exchange (ETDEWEB)

    Burt, G.; Dexter, A.; /Cockcroft Inst. Accel. Sci. Tech.; Beard, C.; Goudket, P.; McIntosh, P.; /Daresbury; Bellantoni, L.; /Fermilab; Grimm, T.; Li, Z.; Xiao, L.; /SLAC

    2011-10-20

    The International Linear Collider (ILC) will require two dipole cavities to 'crab' the electron and positron bunches prior to their collision. It is proposed to use two 9 cell SCRF dipole cavities operating at a frequency of 3.9 GHz, with a transverse gradient of 3.8MV/m in order to provide the required transverse kick. Extensive numerical modelling of this cavity and its couplers has been performed. Aluminium prototypes have been manufactured and tested to measure the RF properties of the cavity and couplers. In addition single cell niobium prototypes have been manufactured and tested in a vertical cryostat. The International Collider (ILC) [1] collides bunches of electrons and positrons at a crossing angle of 14 mrad. The angle between these bunches causes a loss in luminosity due to geometric effects [2]. The luminosity lost from this geometric effect can be recovered by rotating the bunches into alignment prior to collision. One possible method of rotating the bunches is to use a crab cavity [3]. A crab cavity is a transverse defecting cavity, where the phase of the cavity is such that the head and tail of the bunch receive equal and opposite kicks. As the bunches are only 500 nm wide in the horizontal plane, the cavity phase must be strictly controlled to avoid the bunch centre being deflected too much. In order to keep the phase stability within the required limits it is required that the cavity be superconducting to avoid thermal effects in both the cavity and its RF source. At the location of the crab cavity in the ILC there is only 23 cm separation between the centre of the cavity and the extraction line, hence the cavity must be small enough to fit in this space. This, along with the difficulty of making high frequency SRF components, set the frequency of the cavity to 3.9 GHz.

  8. A micropillar for cavity optomechanics

    Energy Technology Data Exchange (ETDEWEB)

    Kuhn, Aurélien; Neuhaus, Leonhard; Deléglise, Samuel; Briant, Tristan; Cohadon, Pierre-François; Heidmann, Antoine [Laboratoire Kastler Brossel, UPMC-ENS-CNRS, Paris (France); Van Brackel, Emmanuel [Département de Physique, ENS, Paris (France); Chartier, Claude; Ducloux, Olivier; Le Traon, Olivier [Département Mesures Physiques, ONERA, Châtillon (France); Michel, Christophe; Pinard, Laurent; Flaminio, Raffaele [Laboratoire des Matériaux Avancés, IN2P3-CNRS, Lyon (France)

    2014-12-04

    Demonstrating the quantum ground state of a macroscopic mechanical object is a major experimental challenge in physics, at the origin of the rapid emergence of cavity optomechanics. We have developed a new generation of optomechanical devices, based on a microgram quartz micropillar with a very high mechanical quality factor. The structure is used as end mirror in a Fabry-Perot cavity with a high optical finesse, leading to ultra-sensitive interferometric measurement of the resonator displacement. We expect to reach the ground state of this optomechanical resonator by combining cryogenic cooling in a dilution fridge at 30 mK and radiation-pressure cooling. We have already carried out a quantum-limited measurement of the micropillar thermal noise at low temperature.

  9. RF cavity vacuum interlock system

    Science.gov (United States)

    Jordan, K.; Crawford, K.; Bundy, R.; Dylla, H. F.; Heckman, J.; Marshall, J.; Nichols, R.; Osullivan, S.; Preble, J.; Robb, J.

    1992-03-01

    The Continuous Electron Beam Accelerator Facility (CEBAF), a continuous wave (CW) 4 GeV Electron Accelerator is undergoing construction in Newport News, Virginia. When completed in 1994, the accelerator will be the largest installation of radio-frequency superconductivity. Production of cryomodules, the fundamental building block of the machine, has started. A cryomodule consists of four sets of pairs of 1497 MHz, 5 cell niobium cavities contained in separate helium vessels and mounted in a cryostat with appropriate end caps for helium supply and return. Beam vacuum of the cavities, the connecting beam piping, the waveguides, and the cryostat insulating vacuum are crucial to the performance of the machine. The design and initial experience of the vacuum systems for the first 2 1/4 cryomodules that makeup the 45 MEV injector are discussed.

  10. Multi-color Cavity Metrology

    CERN Document Server

    Izumi, Kiwamu; Barr, Bryan; Betzwieser, Joseph; Brooks, Aidan; Dahl, Katrin; Doravari, Suresh; Driggers, Jennifer C; Korth, W Zach; Miao, Haixing; Rollins, Jameson; Vass, Stephen; Yeaton-Massey, David; Adhikari, Rana

    2012-01-01

    Long baseline laser interferometers used for gravitational wave detection have proven to be very complicated to control. In order to have sufficient sensitivity to astrophysical gravitational waves, a set of multiple coupled optical cavities comprising the interferometer must be brought into resonance with the laser field. A set of multi-input, multi-output servos then lock these cavities into place via feedback control. This procedure, known as lock acquisition, has proven to be a vexing problem and has reduced greatly the reliability and duty factor of the past generation of laser interferometers. In this article, we describe a technique for bringing the interferometer from an uncontrolled state into resonance by using harmonically related external fields to provide a deterministic hierarchical control. This technique reduces the effect of the external seismic disturbances by four orders of magnitude and promises to greatly enhance the stability and reliability of the current generation of gravitational wav...

  11. Tuberculosis involving the oral cavity

    OpenAIRE

    Ferguson, Kathleen A.; McCormack, David G

    1993-01-01

    The oral cavity is a rare site for extrapulmonary tuberculosis. A case is reported of a young woman with dysphagia and oral ulceration. The original mucosal biopsy was negative on smear for acid-fast bacilli, and the patient subsequently developed pulmonary symptoms. A diagnosis of Mycobacterium tuberculosis was ultimately made on open lung biopsy. Complete resolution of both mouth lesion and chest involvement occurred with standard antituberculous therapy.

  12. Quantum signalling in cavity QED

    OpenAIRE

    Jonsson, Robert H.; Martin-Martinez, Eduardo; Kempf, Achim

    2013-01-01

    We consider quantum signalling between two-level quantum systems in a cavity, in the pertubative regime of the earliest possible arrival times of the signal. We present two main results: First we find that, perhaps surprisingly, the analogue of amplitude modulated signalling (Alice using her energy eigenstates |g>, |e>, as in the Fermi problem) is generally sub-optimal for communication. Namely, e.g., phase modulated signalling (Alice using, e.g., |+>,|e>-states) overcomes the quantum noise a...

  13. Retention proposal in complex cavities.

    Directory of Open Access Journals (Sweden)

    Pedro Alvarez Rodríguez

    2003-12-01

    Full Text Available Background: Dental Operatory is the main structure in which Odontology lies. It is not an easy discipline that gives enjoyable results with little effort due to the difficulties that a correct reconstruction of a destroyed dental element offers.The frequency with which pulpar injury occurs while anchoring additional retainers in complex cavities, the technical difficulties the lack of these devices cause and the need to simplify dental procedures lead this study to show the advantages to substitute additional retainers for a retainer surcus. Method: An observational descriptive study was applied to 53 patients(42% of the universe , sample which was selected by means of a simple randomized sample . From a proximal-occlusal cavity, the preparations were extended in a box-like shape towards the bucal or lingual region and the additional retainers were substituted for a surcus which was performed in the gingival wall of the preparation. Calcium Hydroxide of rapid dryness was used as a cavity cover and Policarboxilate cement as a base; then the amalgam restoration was performed. The number of restorations were studied taking into account the patient´s age and the failures due to fractures of amalgam, loss of vitality and periapical changes were assessed taking into consideration the patient´s age and a one- year follow up. Results: Most of the amalgam restorations were performed in patients aged from 35 to 59 years and the relative frequencies due to fractures of amalgam, loss of vitality and periapical changes were very low. Conclusion: The substitution of additional retainers for a retainer surcus in complex cavities of vital molars showed to be advantageous because it guarantees a less degree of pulpar damage and less pulpar damage.

  14. CRAB Cavity in CERN SPS

    OpenAIRE

    Kim, H. J.; Sen, T.

    2012-01-01

    Beam collisions with a crossing angle at the interaction point have been applied in high intensity colliders to reduce the effects of parasitic collisions which induce emittance growth and beam lifetime deterioration. The crossing angle causes the geometrical reduction of the luminosity. Crab cavity can be one of the most promising ways to compensate the crossing angle and to realize effective head-on collisions. Moreover, the crab crossing mitigates the synchro-betatron resonances due to the...

  15. Retention proposal in complex cavities.

    OpenAIRE

    Pedro Alvarez Rodríguez; Eduardo M. Curbeira Hernández; Eduardo Duarte Marrero; Yisell Peláez Rivas; Aracelis Navarro Sánchez

    2003-01-01

    Background: Dental Operatory is the main structure in which Odontology lies. It is not an easy discipline that gives enjoyable results with little effort due to the difficulties that a correct reconstruction of a destroyed dental element offers.The frequency with which pulpar injury occurs while anchoring additional retainers in complex cavities, the technical difficulties the lack of these devices cause and the need to simplify dental procedures lead this study to show the advantages to subs...

  16. Superconducting versus normal conducting cavities

    OpenAIRE

    Podlech, Holger

    2013-01-01

    One of the most important issues of high-power hadron linacs is the choice of technology with respect to superconducting or room-temperature operation. The favour for a specific technology depends on several parameters such as the beam energy, beam current, beam power and duty factor. This contribution gives an overview of the comparison between superconducting and normal conducting cavities. This includes basic radiofrequency (RF) parameters, design criteria, limitations, required RF and plu...

  17. LHC crab-cavity aspects and strategy

    International Nuclear Information System (INIS)

    The 3rd LHC Crab Cavity workshop (LHC-CC09) took place at CERN in October 2009. It reviewed the current status and identified a clear strategy towards a future crab-cavity implementation. Following the success of crab cavities in KEK-B and the strong potential for luminosity gain and leveling, CERN will pursue crab crossing for the LHC upgrade. We present a summary and outcome of the variousworkshop sessions which have led to the LHC crab-cavity strategy, covering topics like layout, cavity design, integration, machine protection, and a potential validation test in the SPS.

  18. Cavity lining in primary teeth.

    Science.gov (United States)

    Chauhan, Ravi

    2016-03-01

    Data sourcesEmbase, Medline, Cochrane Central, Biomed Central and Open Grey databases and bibliographies of identified studies.Study selectionRandomised controlled trials investigating humans with primary caries lesions receiving operative treatment involving caries removal and restoration, with minimum two treatment groups comparing different cavity treatments before restoration (no lining versus lining) were included.Data extraction and synthesisData were extracted independently by two reviewers and study quality assessed using the Cochrane risk of bias tool. Random effect meta-analysis was carried out.ResultsThree studies involving a total of 89 patients were included. All the studies involved primary teeth and were conducted in Brazil. Follow-up periods ranged from 26-53 months. All the studies were considered to be at high risk of bias. Restoring the cavity without lining did not significantly affect the risk of failure. The quality of the evidence was low.ConclusionsCurrent evidence does not support strong recommendations to use or not to use liners after caries removal and before restoring cavities. Our findings are restricted to primary teeth after selective excavation, with only one liner (calcium hydroxide) being used for comparison. PMID:27012571

  19. Novel Geometries for the LHC Crab Cavity

    International Nuclear Information System (INIS)

    In 2017 the LHC is envisioned to increase its luminosity via an upgrade. This upgrade is likely to require a large crossing angle hence a crab cavity is required to align the bunches prior to collision. There are two possible schemes for crab cavity implementation, global and local. In a global crab cavity the crab cavity is far from the IP and the bunch rotates back and forward as it traverses around the accelerator in a closed orbit. For this scheme a two-cell elliptical squashed cavity at 800 MHz is preferred. To avoid any potential beam instabilities all the parasitic modes of the cavities must be damped strongly, however crab cavities have lower order and same order modes in addition to the usual higher order modes and hence a novel damping scheme must be used to provide sufficient damping of these modes. In the local scheme two crab cavities are placed at each side of the IP two start and stop rotation of the bunches. This would require crab cavities much smaller transversely than in the global scheme but the frequency cannot be increased any higher due to the long bunch length of the LHC beam. This will require a novel compact crab cavity design. A superconducting version of a two rod coaxial deflecting cavity as a suitable design is proposed in this paper.

  20. Construction of cavity fabrication facility in KEK

    International Nuclear Information System (INIS)

    In the development of the superconducting cavity for accelerator that is the main composition equipment of international linear collider (ILC), electron beam welding (EBW) becomes an important process on the cavity of which the Nb material is used. The technology of EBW influences the cavity performance that is cavity gradient. Because of EBW in the equator part of cavities and large amount of process is needed for cavity manufacturing process. In KEK we constructs the pilot plant where the superconducting cavity processing technology by EBW. A clean room was completed as of March of 2010, and the main process equipment except EBW and the CP processor were installed in a clean room. As for the EBW machine, it is scheduled to install it in March, 2011. (author)

  1. SPS RF System an Accelerating Cavity

    CERN Multimedia

    1975-01-01

    The picture shows one of the two initially installed cavities. The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also gradually increased: by end 1980 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412017X, 7411048X.

  2. Scaled experiments of explosions in cavities

    Science.gov (United States)

    Grun, J.; Cranch, G. A.; Lunsford, R.; Compton, S.; Walton, O. R.; Weaver, J.; Dunlop, W.; Fournier, K. B.

    2016-05-01

    Consequences of an explosion inside an air-filled cavity under the earth's surface are partly duplicated in a laboratory experiment on spatial scales 1000 smaller. The experiment measures shock pressures coupled into a block of material by an explosion inside a gas-filled cavity therein. The explosion is generated by suddenly heating a thin foil that is located near the cavity center with a short laser pulse, which turns the foil into expanding plasma, most of whose energy drives a blast wave in the cavity gas. Variables in the experiment are the cavity radius and explosion energy. Measurements and GEODYN code simulations show that shock pressures measured in the block exhibit a weak dependence on scaled cavity radius up to ˜25 m/kt1/3, above which they decrease rapidly. Possible mechanisms giving rise to this behavior are described. The applicability of this work to validating codes used to simulate full-scale cavity explosions is discussed.

  3. CHECHIA cavity driving with FPGA controller

    International Nuclear Information System (INIS)

    The initial control of the superconductive cavity has recently been performed by applying the FPGA (Field Programmable Gate Array) technology system in DESY Hamburg. This first experiment turned attention to the general recognition of the cavity features and projected control methods. The electrical model of the cavity is taken as a consideration origin. The calibration of the signal channel is considered as a key preparation for an efficient cavity driving. The cavity parameters identification is confirmed as a proper approach for the required performance: driving on resonance during filling and field stabilization during flattop time with reasonable power consumption. The feed-forward and feedback modes were applied successfully for the CHECHIA cavity driving. Representative results of experiments are presented for different levels of the cavity field gradient. (orig.)

  4. Photonic sensing of the atmosphere by absorption spectroscopy

    International Nuclear Information System (INIS)

    Chemically reactive atmospheric species play a crucial role in tropospheric processes which affect regional air quality and global climate change. Contrary to long-lived species such as greenhouse gases, interference-free accurate and precise concentration assessments of strongly reactive short-lived species represent a real challenge. In this paper, we report on the recent progress in spectroscopic instrumental developments for monitoring of OH, NO3, HONO and NO2 by using modern photonic sources (Quantum Cascade Laser, distributed feedback diode laser, light emitting diode) in conjunction with high-sensitivity spectroscopic measurement techniques such as multi-pass cell based long optical path length absorption spectroscopy, wavelength-modulation enhanced off-axis integrated cavity output spectroscopy, Faraday rotation spectroscopy, incoherent broadband cavity enhanced absorption spectroscopy. The main techniques available for routine atmospheric measurements of OH, NO3 and HONO are overviewed, in comparison with the emerging modern photonic spectroscopy techniques.

  5. Intrinsic limitation of cavity-enhanced Faraday detection of spin noise in quantum wells and quantum dots

    Science.gov (United States)

    Scalbert, D.

    2016-04-01

    Spin noise spectroscopy is a quite attractive experimental tool for studying unperturbed spin dynamics and magnetic resonance in semiconductor nanostructures. However in some cases its practical interest maybe severely limited by the weakness of the spin noise signal to be detected. In this paper we examine by how much the detection of spin noise of magnetic atoms or of nuclei, in quantum wells or quantum dots, can be improved by making use of cavity-enhanced Faraday rotation. The conditions for optimized cavities are first determined. In reflection geometry it corresponds to tune the cavity to the critical point of impedance matching. It is shown that even for optimized cavities the enhancement in spin noise detection is intrinsically limited by absorption. It turns out that the cavity effect improves the spin noise detection only when the inhomogeneous broadening of the involved optical resonance is large compared to its radiative broadening.

  6. Moessbauer spectroscopy

    International Nuclear Information System (INIS)

    This book is addressed to persons interested in learning about what has been done and what can be done with Moessbauer spectroscopy. In an introductory chapter the basic principle is explained and the general parameters governing Moessbauer spectroscopy are tabulated. For the following chapters various disciplines are chosen and the wide applicability of this measuring technique is demonstrated. The second chapter discusses a few representative examples of chemical interesting information being reflected by isomer shifts and quadrupole splittings, particularly with respect to bonding and structural properties. The third chapter deals with some applications of Moessbauer spectroscopy for characterizing magnetic compounds and its use for magnetic structure investigations, particularly by making use of polarized radiation. The fourth chapter describes the use of the Moessbauer spectroscopy for studying iron in biological molecules. As an example of recent applications to mineralogy and geology the results of the studies of lunar samples are reviewed in the fifth chapter. Finally, in the last chapter, work is described on the use of Moessbauer spectroscopy in physical metallurgy, particularly quantitative analyses which have enabled metallurgists to solve many old problems. (orig./FW)

  7. Observation and characterization of cavity Rydberg polaritons

    Science.gov (United States)

    Ningyuan, Jia; Georgakopoulos, Alexandros; Ryou, Albert; Schine, Nathan; Sommer, Ariel; Simon, Jonathan

    2016-04-01

    We experimentally demonstrate the emergence of a robust quasiparticle, the cavity Rydberg polariton, when an optical cavity photon hybridizes with a collective Rydberg excitation of a laser-cooled atomic ensemble. Free-space Rydberg polaritons have recently drawn intense interest as tools for quantum information processing and few-body quantum science. Here, we explore the properties of their cavity counterparts in the single-particle sector, observing an enhanced lifetime and slowed dynamics characteristic of cavity dark polaritons. We measure the range of cavity frequencies over which the polaritons persist, corresponding to the spectral width available for polariton quantum dynamics, and the speed limit for quantum information processing. Further, we observe a cavity-induced suppression of inhomogeneous broadening channels and demonstrate the formation of Rydberg polaritons in a multimode cavity. In conjunction with recent demonstrations of Rydberg-induced cavity nonlinearities, our results point the way towards using cavity Rydberg polaritons as a platform for creating high-fidelity photonic quantum materials and, more broadly, indicate that cavity dark polaritons offer enhanced stability and control uniquely suited to optical quantum information processing applications beyond the Rydberg paradigm.

  8. Optical Spectroscopy

    DEFF Research Database (Denmark)

    Thyrhaug, Erling

    The work presented in this thesis is broadly concerned with how complexation reactions and molecular motion can be characterized with the standard techniques in optical spectroscopy. The thesis aims to show a relatively broad range of methods for probing physico-chemical properties in fluorophore...... information about chemical equilibria, kinetics and molecular motion by monitoring changes in optical properties of the system. The five presented research projects are largely unrelated to each other both in aim and in what property is probed, however they are all connected in that they are fluorophore...... containing systems and are characterized using techniques in optical spectroscopy. Of the standard techniques in optical spectroscopy, particular attention has been paid to those based on time-resolved measurements and polarization, which is reflected in the experiment design in the projects. Not all of the...

  9. Cavities Formation in Sedimentary Deposits

    Czech Academy of Sciences Publication Activity Database

    Kulaviak, Lukáš; Růžička, Marek; Drahoš, Jiří; Hladil, Jindřich

    Bratislava: Slovak Society of Chemical Engineering , 2008 - (Markoš, J.), s. 241 ISBN 978-80-227-2903-1. [35th International Conference of Slovak Society of Chemical Engineering . Tatranské Matliare (SK), 26.05.2008-30.05.2008] R&D Projects: GA ČR GA104/07/1110; GA ČR GA104/06/1418; GA AV ČR IAAX00130702; GA ČR GP104/06/P287 Institutional research plan: CEZ:AV0Z40720504; CEZ:AV0Z30130516 Keywords : suspension * cavities * stromatactis Subject RIV: CI - Industrial Chemistry, Chemical Engineering

  10. Broadband tuning of optomechanical cavities

    Science.gov (United States)

    Wiederhecker, Gustavo S.; Manipatruni, Sasikanth; Lee, Sunwoo; Lipson, Michal

    2011-01-01

    We demonstrate broadband tuning of an optomechanical microcavity optical resonance by exploring the large optomechanical coupling of a double-wheel microcavity and its uniquely low mechanical stiffness. Using a pump laser with only 13 mW at telecom wavelengths we show tuning of the silicon nitride microcavity resonances over 32 nm. This corresponds to a tuning power efficiency of only 400 $\\mu$W/nm. By choosing a relatively low optical Q resonance ($\\approx$18,000) we prevent the cavity from reaching the regime of regenerative optomechanical oscillations. The static mechanical displacement induced by optical gradient forces is estimated to be as large as 60 nm.

  11. Mass renormalization in cavity QED

    International Nuclear Information System (INIS)

    We show that the presence of a background medium and a boundary surface or surfaces in cavity QED produces no change in the energy shift of a free charged particle due to its coupling to the fluctuating electromagnetic field of the vacuum. This clarifies that the electromagnetic and the observed mass of the charged particle are not affected by the modification of the field of the vacuum. The calculations are nonrelativistic and restricted to the dipole approximation but are otherwise based on the general requirements of causality.

  12. Broadband Tuning of Optomechanical Cavities

    OpenAIRE

    Wiederhecker, Gustavo S.; Manipatruni, Sasikanth; Lee, Sunwoo; Lipson, Michal

    2010-01-01

    We demonstrate broadband tuning of an optomechanical microcavity optical resonance by exploring the large optomechanical coupling of a double-wheel microcavity and its uniquely low mechanical stiffness. Using a pump laser with only 13 mW at telecom wavelengths we show tuning of the silicon nitride microcavity resonances over 32 nm. This corresponds to a tuning power efficiency of only 400 $\\mu$W/nm. By choosing a relatively low optical Q resonance ($\\approx$18,000) we prevent the cavity from ...

  13. Broadband Tuning of Optomechanical Cavities

    CERN Document Server

    Wiederhecker, Gustavo S; Lee, Sunwoo; Lipson, Michal

    2010-01-01

    We demonstrate broadband tuning of an optomechanical microcavity optical resonance by exploring the large optomechanical coupling of a double-wheel microcavity and its uniquely low mechanical stiffness. Using a pump laser with only 13 mW at telecom wavelengths we show tuning of the silicon nitride microcavity resonances over 32 nm. This corresponds to a tuning power efficiency of only 400 $\\mu$W/nm. By choosing a relatively low optical Q resonance ($\\approx$18,000) we prevent the cavity from reaching the regime of regenerative optomechanical oscillations. The static mechanical displacement induced by optical gradient forces is estimated to be as large as 60 nm.

  14. Basketballs as spherical acoustic cavities

    Science.gov (United States)

    Russell, Daniel A.

    2010-06-01

    The sound field resulting from striking a basketball is found to be rich in frequency content, with over 50 partials in the frequency range of 0-12 kHz. The frequencies are found to closely match theoretical expectations for standing wave patterns inside a spherical cavity. Because of the degenerate nature of the mode shapes, explicit identification of the modes is not possible without internal investigation with a microphone probe. A basketball proves to be an interesting application of a boundary value problem involving spherical coordinates.

  15. Nuclear spectroscopy

    CERN Document Server

    Ajzenberg-Selove, Fay

    1960-01-01

    Nuclear Spectroscopy, Part A deals with the experimental and theoretical techniques involved in nuclear spectroscopy.This book discusses the interactions of charged particles with matter, gaseous ionization detectors, and particular mass attenuation coefficients. The magnetic gamma-ray spectrometers for photo or internal-conversion electrons, general characteristics of cross-section variation with energy, and measurement of fast neutron spectra are also elaborated. This text likewise covers the elastic scattering of photons by nuclei and measurement of widths of gamma-radiating levels.This pub

  16. Optogalvanic spectroscopy

    International Nuclear Information System (INIS)

    Laser induced optogalvanic spectroscopy in a hollow cathode-produced plasma has been used to resolve the isotopic structure of some absorption lines in uranium. We have shown that the optogalvanic signal associated with any isotope can be related to the concentration of that isotope in a multi-isotopic sample. From the results we have obtained, optogalvanic spectroscopy of sputtered samples appears to be an interesting approach to the isotopic analysis of both natural and enriched uranium and could easily be applied to the analysis of other fissile elements, such as the plutonium isotopes

  17. Deterministic cavity quantum electrodynamics with trapped ions

    International Nuclear Information System (INIS)

    We have employed radio-frequency trapping to localize a single 40Ca+-ion in a high-finesse optical cavity. By means of laser Doppler cooling, the position spread of the ion's wavefunction along the cavity axis was reduced to 42 nm, a fraction of the resonance wavelength of ionized calcium (λ = 397 nm). By controlling the position of the ion in the optical field, continuous and completely deterministic coupling of ion and field was realized. The precise three-dimensional location of the ion in the cavity was measured by observing the fluorescent light emitted upon excitation in the cavity field. The single-ion system is ideally suited to implement cavity quantum electrodynamics under cw conditions. To this end we operate the cavity on the D3/2-P1/2 transition of 40Ca+ (λ 866 nm). Applications include the controlled generation of single-photon pulses with high efficiency and two-ion quantum gates

  18. Silicon Integrated Cavity Optomechanical Transducer

    Science.gov (United States)

    Zou, Jie; Miao, Houxun; Michels, Thomas; Liu, Yuxiang; Srinivasan, Kartik; Aksyuk, Vladimir

    2013-03-01

    Cavity optomechanics enables measurements of mechanical motion at the fundamental limits of precision imposed by quantum mechanics. However, the need to align and couple devices to off-chip optical components hinders development, miniaturization and broader application of ultrahigh sensitivity chip-scale optomechanical transducers. Here we demonstrate a fully integrated and optical fiber pigtailed optomechanical transducer with a high Q silicon micro-disk cavity near-field coupled to a nanoscale cantilever. We detect the motion of the cantilever by measuring the resonant frequency shift of the whispering gallery mode of the micro-disk. The sensitivity near the standard quantum limit can be reached with sub-uW optical power. Our on-chip approach combines compactness and stability with great design flexibility: the geometry of the micro-disk and cantilever can be tailored to optimize the mechanical/optical Q factors and tune the mechanical frequency over two orders of magnitudes. Electrical transduction in addition to optical transduction was also demonstrated and both can be used to effectively cool the cantilever. Moreover, cantilevers with sharp tips overhanging the chip edge were fabricated to potentially allow the mechanical cantilever to be coupled to a wide range of off-chip systems, such as spins, DNA, nanostructures and atoms on clean surfaces.

  19. Malignant melanoma of the oral cavity

    OpenAIRE

    M.S. Hashemi Pour

    2006-01-01

    Oral malignant melanoma is a rare disease. The common sites of its occurrence are the palate and gingiva with the maxillary arch being affected 80% of the time. Because of their presence at relatively obscure areas in the oral cavity, most of the malignant melanomas of the oral cavity are diagnosed at a late stage. These lesions are associated with poor prognosis. The dental clinician must therefore carefully examine the head, neck, and oral cavity, and any pigmented lesion that may ex...

  20. Hybrid Microwave-Cavity Heat Engine

    OpenAIRE

    Bergenfeldt, Christian; Samuelsson, Peter; Sothmann, Björn; Flindt, Christian; Büttiker, Markus

    2013-01-01

    We propose and analyze the use of hybrid microwave cavities as quantum heat engines. A possible realization consists of two macroscopically separated quantum dot conductors coupled capacitively to the fundamental mode of a microwave cavity. We demonstrate that an electrical current can be induced in one conductor through cavity-mediated processes by heating up the other conductor. The heat engine can reach Carnot efficiency with optimal conversion of heat to work. When the system delivers the...