Theoretical modeling of structure and function of cathode catalyst layers in PEMFC

International Nuclear Information System (INIS)

Wang, Q.; Eikerling, M.; Song, D.; Liu, Z.

2004-01-01

'Full text:' In this work, we first investigate transport and reaction kinetics in single agglomerates of cathode catalyst layers in proton exchange fuel cells. Two types of spherical agglomerates are evaluated, which represent limiting structures that can be obtained by distinct synthetic procedures. One type consists of a mixture of carbon/catalyst particles and proton conducting perfluorosulfonated ionomer (PFSI). The other type consists of carbon/catalyst particles and water-filled pores. Performance of the former type is rationalized on the basis of the well-known Thiele-modulus. Characteristics of the latter type are studied using Nernst-Planck and Poisson equations. Aspects of current conversion, reactant and current distributions, and catalyst utilization are explored. In general, the PFSI-filled agglomerates exhibit more homogeneous distributions of reaction rates. Effectiveness factors for them are close to one. However, it was found that proton penetration depths in waterflooded agglomerates could be quite significant as well under certain conditions, resulting in unexpectedly high catalyst utilization. The effects of agglomerate radius and of boundary conditions at the agglomerate surface are studied. Moreover, using the same approach, we evaluate the performance of a flat PFSI-free catalyst layer with water-filled pore space. Compared with conventional composite catalyst layers impregnated with PFSI, the PFSI-free layer exhibits better performance and high Pt utilization for thicknesses less than 0.1 μm. The significance of these results for the optimization catalyst layers in view of operation conditions and synthesis methods is discussed. (author)

Scalable synthesis of palladium nanoparticle catalysts by atomic layer deposition

International Nuclear Information System (INIS)

Liang Xinhua; Lyon, Lauren B.; Jiang Yingbing; Weimer, Alan W.

2012-01-01

Atomic layer deposition (ALD) was used to produce Pd/Al 2 O 3 catalysts using sequential exposures of Pd(II) hexafluoroacetylacetonate and formalin at 200 °C in a fluidized bed reactor. The ALD-prepared Pd/alumina catalysts were characterized by various methods including hydrogen chemisorption, XPS, and TEM, and compared with a commercially available 1 wt% Pd/alumina catalyst, which was also characterized. The content of Pd on alumina support and the size of Pd nanoparticles can be controlled by the number of ALD-coating cycles and the dose time of the Pd precursor. One layer of organic component from the Pd precursor remained on the Pd particle surface. The ALD 0.9 wt% Pd/alumina had greater active metal surface area and percent metal dispersion than the commercial 1 wt% Pd/alumina catalyst. The ALD and commercial catalysts were subjected to catalytic testing to determine their relative activities for glucose oxidation to gluconic acid in aqueous solution. The ALD 0.9 wt% Pd/alumina catalyst had comparable activity as compared to the commercial 1 wt% Pd catalyst. No noticeable amount of Pd leaching was observed for the ALD-prepared catalysts during the vigorously stirred reaction.

High performance and durability of order-structured cathode catalyst layer based on TiO_2@PANI core-shell nanowire arrays

International Nuclear Information System (INIS)

Chen, Ming; Wang, Meng; Yang, Zhaoyi; Wang, Xindong

2017-01-01

Highlights: • TiO_2@PANI core-shell nanowire arrays were prepared and applied as catalyst support. • As-prepared Pt-TiO_2@PANI core-shell nanowire arrays were applied as order-structured cathode catalyst layer. • The novel cathode catalyst structure without Nafion"® ionomer enhance the performance and durability of PEMFC. - Abstract: In this paper, an order-structured cathode catalyst layer consisting of Pt-TiO_2@PANI core-shell nanowire arrays that in situ grown on commercial gas diffusion layer (GDL) are prepared and applied to membrane electrode assembly (MEA) of proton exchange membrane fuel cell (PEMFC). In order to prepare the TiO_2@PANI core-shell nanowire arrays with suitable porosity and prominent conductivity, the morphologies of the TiO_2 nanoarray and electrochemical polymerization process of aniline are schematically investigated. The MEA with order-structured cathode catalyst layer is assembled in the single cell to evaluate the electrochemical performance and durability of PEMFC. As a result, the PEMFC with order-structured cathode catalyst layer shows higher peak power density (773.54 mW cm"−"2) than conventional PEMFC (699.30 mW cm"−"2). Electrochemically active surface area (ECSA) and charge transfer impedance (R_c_t) are measured before and after accelerated degradation test (ADT), and the corresponding experimental results indicate the novel cathode structure exhibits a better stability with respect to conventional cathode. The enhanced electrochemical performance and durability toward PEMFC can be ascribed to the order-structured cathode nanoarray structure with high specific surface area increases the utilization of catalyst and reduces the tortuosity of transport pathways, and the synergistic effect between TiO_2@PANI support and Pt nanoparticles promotes the high efficiency of electrochemical reaction and improves the stability of catalyst. This research provides a facile and controllable method to prepare order

Degradation of 4-Chlorophenol Under Sunlight Using ZnO Nanoparticles as Catalysts

Science.gov (United States)

Rajar, Kausar; Sirajuddin; Balouch, Aamna; Bhanger, M. I.; Sherazi, Tufail H.; Kumar, Raj

2018-03-01

Herein we demonstrate a simplistic microwave assisted chemical precipitation approach regarding the synthesis of zinc oxide nanoparticles. As-prepared ZnO nanoparticles (NPs) were characterized by UV-visible spectroscopy, Fourier transform infra-red spectroscopy, atomic force microscopy and x-ray diffractometry and scrutinized as photo-catalysts for degradation of 4-chlorophenol (4-CP) under sunlight. The study substantiated that 98.5% of 4-CP was degraded within 20 min in the absence of initiator like H2O2 which reflects an outstanding prospective use for ZnO NPs as photo-catalysts. The nanocatalysts were recycled four times and still showed catalytic efficiency up to 95.5% for degradation of 4-CP in the specified 20 min.

Simulation of the catalyst layer in PEMFC based on a novel two-phase lattice model

Energy Technology Data Exchange (ETDEWEB)

Zhang Jiejing; Yang Wei; Xu Li [School of Chemical Engineering and Technology, State Key Laboratory of Chemical Engineering, Tianjin Key Laboratory of Membrane Science and Desalination Technology, Tianjin University, Tianjin 300072 (China); Wang Yuxin, E-mail: yxwang@tju.edu.cn [School of Chemical Engineering and Technology, State Key Laboratory of Chemical Engineering, Tianjin Key Laboratory of Membrane Science and Desalination Technology, Tianjin University, Tianjin 300072 (China)

2011-08-01

Highlights: > We propose a novel two phase lattice model of catalyst layer in PEMFC. > The model features a catalyst phase and a mixed ionomer and pores phase. > Transport and electrochemical reaction in the lattice are simulated. > The model enables more accurate results than pore-solid two phase model. > Profiles of oxygen level and reaction rate across catalyst layer vary with cell current. - Abstract: A lattice model of catalyst layer in proton exchange membrane fuel cells (PEMFCs), consisting of randomly distributed catalyst phase (C phase) and mixed ionomer-pore phase (IP phase), was established by means of Monte Carlo method. Transport and electrochemical reactions in the model catalyst layer were calculated. The newly proposed C-IP model was compared with previously established pore-solid two phase model. The variation of oxygen level and reaction rate along the thickness of catalyst layer with cell current was discussed. The effect of ionomer distribution across catalyst layer was studied by comparing profiles of oxygen level, reaction rate and overpotential, as well as corresponding polarization curves.

A novel catalyst layer structure based surface-patterned Nafion® membrane for high-performance direct methanol fuel cell

DEFF Research Database (Denmark)

Chen, Ming; Wang, Meng; Ding, Xianan

2018-01-01

.5% respectively, compared with the conventional catalyst layer. Performance improvement is attributed to the fact that the novel catalyst layer structure optimizes the electrolyte membrane/catalyst layer and gas diffusion layer/catalyst layer interfacial structure, which increases the electrochemical reaction......Conventional catalyst layer with a smooth surface exists the larger area of“catalytic dead zone” and reduces the utilization of catalyst. Based on this, a novel catalyst layer structure based surface-patterned Nafion® membrane was designed to achieve more efficient electrochemical reaction...... to prepare the novel catalyst layer, and the effect of pressure on the performance of MEA was investigated. The results suggested that the peak power density of DMFC with optimal novel catalyst layer structure increased by 28.84%, the charge transfer resistances of anode and cathode reduced by 28.8% and 26...

MESOPOROUS ACID SOLID AS A CARRIER FOR METALLOCENE CATALYST IN ETHYLENE POLYMERIZATION AND A CATALYST IN CATALYTIC DEGRADATION OF POLYETHYLENE

Institute of Scientific and Technical Information of China (English)

Wen-xi Cheng; Li-ya Shi; Shi-yun Li; Hui Chen; Tao Tang

2007-01-01

The possibility of mesoporous acid solid as a carrier for metallocene catalyst in ethylene polymerization and catalyst for polyethylene(PE)catalytic degradation was investigated.Here,HMCM-41 and AlMCM-41.and mesoporous silicoaluminophosphate molecular sieves(SAPO1 and SAPO2)were synthesized and used as acid solid.Much more gases were produced during catalytic degradation in PE/acid solid mixtures via in situ polymerization than those via physical mixing.The particle size distribution results exhibited that the particle size of SAPO1 in the PE/SAO1 mixture via in situ polymerization was about 1/14 times of that of the original SAPO1 or SAPO1.supported metallocene catalyst.This work shows a novel technology for chemical recycling of polyolefin.

High performance and durability of order-structured cathode catalyst layer based on TiO{sub 2}@PANI core-shell nanowire arrays

Energy Technology Data Exchange (ETDEWEB)

Chen, Ming; Wang, Meng; Yang, Zhaoyi [State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, 30 College Road, Beijing 100083 (China); School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, 30 College Road, Beijing 100083 (China); Wang, Xindong, E-mail: echem@ustb.edu.cn [State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, 30 College Road, Beijing 100083 (China); School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, 30 College Road, Beijing 100083 (China)

2017-06-01

Highlights: • TiO{sub 2}@PANI core-shell nanowire arrays were prepared and applied as catalyst support. • As-prepared Pt-TiO{sub 2}@PANI core-shell nanowire arrays were applied as order-structured cathode catalyst layer. • The novel cathode catalyst structure without Nafion{sup ®} ionomer enhance the performance and durability of PEMFC. - Abstract: In this paper, an order-structured cathode catalyst layer consisting of Pt-TiO{sub 2}@PANI core-shell nanowire arrays that in situ grown on commercial gas diffusion layer (GDL) are prepared and applied to membrane electrode assembly (MEA) of proton exchange membrane fuel cell (PEMFC). In order to prepare the TiO{sub 2}@PANI core-shell nanowire arrays with suitable porosity and prominent conductivity, the morphologies of the TiO{sub 2} nanoarray and electrochemical polymerization process of aniline are schematically investigated. The MEA with order-structured cathode catalyst layer is assembled in the single cell to evaluate the electrochemical performance and durability of PEMFC. As a result, the PEMFC with order-structured cathode catalyst layer shows higher peak power density (773.54 mW cm{sup −2}) than conventional PEMFC (699.30 mW cm{sup −2}). Electrochemically active surface area (ECSA) and charge transfer impedance (R{sub ct}) are measured before and after accelerated degradation test (ADT), and the corresponding experimental results indicate the novel cathode structure exhibits a better stability with respect to conventional cathode. The enhanced electrochemical performance and durability toward PEMFC can be ascribed to the order-structured cathode nanoarray structure with high specific surface area increases the utilization of catalyst and reduces the tortuosity of transport pathways, and the synergistic effect between TiO{sub 2}@PANI support and Pt nanoparticles promotes the high efficiency of electrochemical reaction and improves the stability of catalyst. This research provides a facile and

Coking- and sintering-resistant palladium catalysts achieved through atomic layer deposition.

Science.gov (United States)

Lu, Junling; Fu, Baosong; Kung, Mayfair C; Xiao, Guomin; Elam, Jeffrey W; Kung, Harold H; Stair, Peter C

2012-03-09

We showed that alumina (Al(2)O(3)) overcoating of supported metal nanoparticles (NPs) effectively reduced deactivation by coking and sintering in high-temperature applications of heterogeneous catalysts. We overcoated palladium NPs with 45 layers of alumina through an atomic layer deposition (ALD) process that alternated exposures of the catalysts to trimethylaluminum and water at 200°C. When these catalysts were used for 1 hour in oxidative dehydrogenation of ethane to ethylene at 650°C, they were found by thermogravimetric analysis to contain less than 6% of the coke formed on the uncoated catalysts. Scanning transmission electron microscopy showed no visible morphology changes after reaction at 675°C for 28 hours. The yield of ethylene was improved on all ALD Al(2)O(3) overcoated Pd catalysts.

Degradation reaction of Diazo reactive black 5 dye with copper (II) sulfate catalyst in thermolysis treatment.

Science.gov (United States)

Lau, Yen-Yie; Wong, Yee-Shian; Ang, Tze-Zhang; Ong, Soon-An; Lutpi, Nabilah Aminah; Ho, Li-Ngee

2018-03-01

The theme of present research demonstrates performance of copper (II) sulfate (CuSO 4 ) as catalyst in thermolysis process to treat reactive black 5 (RB 5) dye. During thermolysis without presence of catalyst, heat was converted to thermal energy to break the enthalpy of chemical structure bonding and only 31.62% of color removal. With CuSO 4 support as auxiliary agent, the thermally cleaved molecular structure was further destabilized and reacted with CuSO 4 . Copper ions functioned to delocalize the coordination of π of the lone paired electron in azo bond, C=C bond of the sp 2 carbon to form C-C of the sp 3 amorphous carbon in benzene and naphthalene. Further, the radicals of unpaired electrons were stabilized and RB 5 was thermally decomposed to methyl group. Zeta potential measurement was carried out to analyze the mechanism of RB 5 degradation and measurement at 0 mV verified the critical chemical concentration (CCC) (0.7 g/L copper (II) sulfate), as the maximum 92.30% color removal. The presence of copper (II) sulfate catalyst has remarkably increase the RB 5 dye degradation as the degradation rate constant without catalyst, k 1 is 6.5224 whereas the degradation rate constant with catalyst, k 2 is 25.6810. This revealed the correlation of conversion of thermal energy from heat to break the chemical bond strength, subsequent fragmentation of RB 5 dye molecular mediated by copper (II) sulfate catalyst. The novel framework on thermolysis degradation of molecular structure of RB 5 with respect to the bond enthalpy and interfacial intermediates decomposition with catalyst reaction were determined.

Carbon nanotube forests growth using catalysts from atomic layer deposition

Energy Technology Data Exchange (ETDEWEB)

Chen, Bingan; Zhang, Can; Esconjauregui, Santiago; Xie, Rongsi; Zhong, Guofang; Robertson, John [Department of Engineering, University of Cambridge, Cambridge CB3 0FA (United Kingdom); Bhardwaj, Sunil [Istituto Officina dei Materiali-CNR Laboratorio TASC, s.s. 14, km 163.4, I-34012 Trieste (Italy); Sincrotone Trieste S.C.p.A., s.s. 14, km 163.4, I-34149 Trieste (Italy); Cepek, Cinzia [Istituto Officina dei Materiali-CNR Laboratorio TASC, s.s. 14, km 163.4, I-34012 Trieste (Italy)

2014-04-14

We have grown carbon nanotubes using Fe and Ni catalyst films deposited by atomic layer deposition. Both metals lead to catalytically active nanoparticles for growing vertically aligned nanotube forests or carbon fibres, depending on the growth conditions and whether the substrate is alumina or silica. The resulting nanotubes have narrow diameter and wall number distributions that are as narrow as those grown from sputtered catalysts. The state of the catalyst is studied by in-situ and ex-situ X-ray photoemission spectroscopy. We demonstrate multi-directional nanotube growth on a porous alumina foam coated with Fe prepared by atomic layer deposition. This deposition technique can be useful for nanotube applications in microelectronics, filter technology, and energy storage.

Impact of anode catalyst layer porosity on the performance of a direct formic acid fuel cell

International Nuclear Information System (INIS)

Bauskar, Akshay S.; Rice, Cynthia A.

2012-01-01

Highlights: ► Lithium carbonate is used as a pore-former to increase porosity of anode catalyst layer. ► Maximum power density increased by 25%. ► Onset potential for formic acid electro-oxidation reduced by 30 mV for anode catalyst layer with 17.5 wt% pore-former. ► Electrochemical impedance spectra confirm increased formic acid concentration inside the anode catalyst layer pores. - Abstract: Direct formic acid fuel cells (DFAFCs) have attracted much attention in the last few years for portable electronic devices, due to their potential of being high efficiency power sources. They have the potential to replace the state-of-the-art batteries in cell phones, PDAs, and laptop computers if their power density and durability can be improved. In the present investigation, the influence of increased anode catalyst layer porosity on DFAFC power density performance is studied. Lithium carbonate (Li 2 CO 3 ) was used as a pore-former in this study because of its facile and complete removal after catalyst layer fabrication. The anode catalyst layers presented herein contained unsupported Pt/Ru catalyst and Li 2 CO 3 (in the range of 0–50 wt%) bound with proton conducting ionomer. Higher DFAFC performance is obtained because of the increased porosity within the anode catalyst layer through enhanced reactant and product mass transport. The maximum power density of DFAFC increased by 25% when pore-former was added to the anode catalyst ink. The formic acid onset potential for the anode catalyst layer with 17.5 wt% pore-former was reduced by 30 mV. A constant phase element based equivalent-circuit model was used to investigate anode impedance spectra. Fitted values for the anode impedance spectra confirm the improvement in performance due to an increase in formic acid concentration inside the anode catalyst layer pores along with efficient transport of reactants and products.

Photo catalytic degradation of nitrobenzene using nanocrystalline TiO2 photo catalyst doped with Zn ions

International Nuclear Information System (INIS)

Reynoso S, E. A.; Perez S, S.; Reyes C, A. P.; Castro R, C. L.; Felix N, R. M.; Lin H, S. W.; Paraguay D, F.; Alonso N, G.

2013-01-01

Photo catalysis is a method widely used in the degradation of organic pollutants of the environment. The development of new materials is very important to improve the photo catalytic properties and to find new applications for TiO 2 as a photo catalyst. In this article we reported the synthesis of a photo catalyst based on TiO 2 doped with Zn 2+ ions highly efficient in the degradation of nitrobenzene. The results of photo catalytic activity experiments showed that the Zn 2+ doped TiO 2 is more active that un-doped TiO 2 catalyst with an efficiency of 99% for the nitrobenzene degradation at 120 min with an apparent rate constant of 35 x 10 -3 min -1 . For the characterization of photo catalyst X-ray diffraction, transmission electron microscopy and Raman spectroscopy were used. (Author)

Piezo-Catalytic Effect on the Enhancement of the Ultra-High Degradation Activity in the Dark by Single- and Few-Layers MoS2 Nanoflowers.

Science.gov (United States)

Wu, Jyh Ming; Chang, Wei En; Chang, Yu Ting; Chang, Chih-Kai

2016-05-01

Single- and few-layer MoS2 nanoflowers are first discovered to have a piezo-catalyst effect, exhibiting an ultra-high degradation activity in the dark by introducing external mechanical strains. The degradation ratio of the Rhodamine-B dye solution reaches 93% within 60 s under ultrasonic-wave assistance in the dark. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

THE USE OF TIO2-ZEOLIT AS A CATALYST ON THE DEGRADATION PROCESS OF ERIONIL RED DYE

Directory of Open Access Journals (Sweden)

Agustin Sumartono

2010-06-01

Full Text Available Degradation of erionil red dye using photo catalytic processes with TiO2-zeolit as a catalyst was carried out. Degradation of the dye was observed in 10 L volume, and erionil red dye was used as a model of organic pollutant. The parameters examinated were  intensity of the spectrum, the decrease of pH, percentage of degradation, and the efectifity TiO2-zeolit  as a catalyst. The use of UV lamp and TiO2-zeolit as a catalyst showed a good results because the dye could be degraded. This could be seen from the decreasing of the intensity of the spectrum  24 h after illumination. The pH of erionil red increased from around 4 into 5.5 which is still acidic. Effectivity of TiO2 composit as a catalyst could be used only two times. The compound resulted from degradation that could be detected using HPLC was oxalic acid.   Keywords: dye, erionil red, photocatalytic, TiO2

Non-Catalytic and MgSO4 - Catalyst based Degradation of Glycerol in Subcritical and Supercritical Water Media

Directory of Open Access Journals (Sweden)

Mahfud Mahfud

2011-02-01

Full Text Available This research aims to study the glycerol degradation reaction in subcritical and supercritical water media. The degradation of glycerol into other products was performed both with sulphate salt catalysts and without catalyst. The reactant was made from glycerol and water with the mass ratio of 1:10. The experiments were carried out using a batch reactor at a constant pressure of 250 kgf/cm2, with the temperature range of 200-400oC, reaction time of 30 minutes, and catalyst mol ratio in glycerol of 1:10 and 1:8. The products of the non-catalytic glycerol degradation were acetaldehyde, methanol, and ethanol. The use of sulphate salt as catalyst has high selectivity to acetaldehyde and still allows the formation alcohol product in small quantities. The mechanism of ionic reaction and free radical reaction can occur at lower temperature in hydrothermal area or subcritical water. Conversion of glycerol on catalytic reaction showed a higher yield when compared with the reaction performed without catalyst

Effect of various gases and chemical catalysts on phenol degradation pathways by pulsed electrical discharges

Energy Technology Data Exchange (ETDEWEB)

Shen Yongjun [Institute of Environmental Pollution Control Technologies, Zhejiang University, Hangzhou 310028 (China); Lei Lecheng [Institute of Environmental Pollution Control Technologies, Zhejiang University, Hangzhou 310028 (China)], E-mail: lclei@zju.edu.cn; Zhang Xingwang; Zhou Minghua; Zhang Yi [Institute of Environmental Pollution Control Technologies, Zhejiang University, Hangzhou 310028 (China)

2008-02-11

The processes of phenol degradation by pulsed electrical discharges were investigated under several kinds of discharge atmospheres (oxygen, argon, nitrogen and ozone) and chemical catalysts (ferrous ion and hydrogen peroxide). The temporal variations of the concentrations of phenol and the intermediate products were monitored by HPLC and GC-MS, respectively. It has been found that the effect of various gases bubbling on phenol degradation rate ranked in the following order: oxygen-containing ozone > oxygen > argon > nitrogen. The high gas bubbling flow rate was beneficial to the removal of phenol. It was found that the degradation proceeded differently when in the presence and absence of catalysts. The phenol removal rate was increased when ferrous ion was added. This considerable enhancement may be due to the Fenton's reaction. What's more, putting the chemical additives hydrogen peroxide into the reactor led to a dramatic increase in phenol degradation rate. The mechanism was due to the direct or indirect photolysis and pyrolysis destruction in plasma channel. Furthermore, the intermediate products were monitored by GC-MS under three degradation conditions. More THBs were generated under degradation conditions without gases bubbling or adding any catalyst, and more DHBs under the condition of adding ferrous ion, and more carboxylic acids under the condition of oxygen-containing ozone gas bubbling. Consequently, three distinct degradation pathways based on different conditions were proposed.

Effect of various gases and chemical catalysts on phenol degradation pathways by pulsed electrical discharges.

Science.gov (United States)

Shen, Yongjun; Lei, Lecheng; Zhang, Xingwang; Zhou, Minghua; Zhang, Yi

2008-02-11

The processes of phenol degradation by pulsed electrical discharges were investigated under several kinds of discharge atmospheres (oxygen, argon, nitrogen and ozone) and chemical catalysts (ferrous ion and hydrogen peroxide). The temporal variations of the concentrations of phenol and the intermediate products were monitored by HPLC and GC-MS, respectively. It has been found that the effect of various gases bubbling on phenol degradation rate ranked in the following order: oxygen-containing ozone>oxygen>argon>nitrogen. The high gas bubbling flow rate was beneficial to the removal of phenol. It was found that the degradation proceeded differently when in the presence and absence of catalysts. The phenol removal rate was increased when ferrous ion was added. This considerable enhancement may be due to the Fenton's reaction. What's more, putting the chemical additives hydrogen peroxide into the reactor led to a dramatic increase in phenol degradation rate. The mechanism was due to the direct or indirect photolysis and pyrolysis destruction in plasma channel. Furthermore, the intermediate products were monitored by GC-MS under three degradation conditions. More THBs were generated under degradation conditions without gases bubbling or adding any catalyst, and more DHBs under the condition of adding ferrous ion, and more carboxylic acids under the condition of oxygen-containing ozone gas bubbling. Consequently, three distinct degradation pathways based on different conditions were proposed.

Effect of various gases and chemical catalysts on phenol degradation pathways by pulsed electrical discharges

International Nuclear Information System (INIS)

Shen Yongjun; Lei Lecheng; Zhang Xingwang; Zhou Minghua; Zhang Yi

2008-01-01

The processes of phenol degradation by pulsed electrical discharges were investigated under several kinds of discharge atmospheres (oxygen, argon, nitrogen and ozone) and chemical catalysts (ferrous ion and hydrogen peroxide). The temporal variations of the concentrations of phenol and the intermediate products were monitored by HPLC and GC-MS, respectively. It has been found that the effect of various gases bubbling on phenol degradation rate ranked in the following order: oxygen-containing ozone > oxygen > argon > nitrogen. The high gas bubbling flow rate was beneficial to the removal of phenol. It was found that the degradation proceeded differently when in the presence and absence of catalysts. The phenol removal rate was increased when ferrous ion was added. This considerable enhancement may be due to the Fenton's reaction. What's more, putting the chemical additives hydrogen peroxide into the reactor led to a dramatic increase in phenol degradation rate. The mechanism was due to the direct or indirect photolysis and pyrolysis destruction in plasma channel. Furthermore, the intermediate products were monitored by GC-MS under three degradation conditions. More THBs were generated under degradation conditions without gases bubbling or adding any catalyst, and more DHBs under the condition of adding ferrous ion, and more carboxylic acids under the condition of oxygen-containing ozone gas bubbling. Consequently, three distinct degradation pathways based on different conditions were proposed

Synthesis, Characterization, and Use of Novel Bimetal Oxide Catalyst for Photoassisted Degradation of Malachite Green Dye

Directory of Open Access Journals (Sweden)

K. L. Ameta

2014-01-01

Full Text Available This work reports a simple, novel, and cost effective synthesis of nanobimetal oxide catalyst using cerium and cadmium nitrates as metal precursors. The cerium-cadmium oxide nanophotocatalyst was synthesized by coprecipitation method and characterized by X-ray powder diffraction method to analyze the particle size. XRD study reveals a high degree of crystallinity and 28.43 nm particle size. The photocatalytic efficiency of the synthesized nanobimetal catalyst was examined by using it for the photocatalytic degradation of malachite green dye. Experiments were conducted to study the effect of various parameters, such as the pH of the dye solution, concentration of dye, amount of catalyst, and light intensity on the rate of dye degradation. The progress of the dye degradation was monitored spectrophotometrically by taking the optical density of the dye solution at regular intervals. Experimental results indicate that the dye degrades best at pH 8.0 with light intensity 600 Wm−2 and catalyst loading 0.03 g/50 mL of dye solution. The rate constant for the reaction was 7.67 × 10−4 s−1.

The catalyst layer and its dimensionality - A look into its ingredients and how to characterize their effects

Science.gov (United States)

Zamel, Nada

2016-03-01

Development of polymer electrolyte membrane (PEM) fuel cells throughout the years is established through its component optimization. This is especially true of its catalyst layer, where structuring of the layer has led to many breakthroughs. The catalyst layer acts as the heart of the cell, where it controls the half-cell reactions and their products. The complex nature of various transport phenomena simultaneously taking place in the layer requires the layer to be heterogeneous in structure. Hence, a delicate balance of the layer's ingredients, coupled with the understanding of the ingredients' interaction, is required. State-of-the-art catalyst layers are composed of a catalyst, its support, a solvent and a binder. Changes in the morphology, structure or material of any of these components ultimately affects the layer's activity and durability. In this review paper, we provide an overview of the various works tailored to understand how each component in the catalyst's ink affects the stability and life-time of the layer.

Catalysts, Protection Layers, and Semiconductors

DEFF Research Database (Denmark)

Chorkendorff, Ib

2015-01-01

Hydrogen is the simplest solar fuel to produce and in this presentation we shall give a short overview of the pros and cons of various tandem devices [1]. The large band gap semiconductor needs to be in front, but apart from that we can chose to have either the anode in front or back using either...... acid or alkaline conditions. Since most relevant semiconductors are very prone to corrosion the advantage of using buried junctions and using protection layers offering shall be discussed [2-4]. Next we shall discuss the availability of various catalysts for being coupled to these protections layers...... and how their stability may be evaluated [5, 6]. Examples of half-cell reaction using protection layers for both cathode and anode will be discussed though some of recent examples under both alkaline and acidic conditions. Si is a very good low band gap semiconductor and by using TiO2 as a protection...

Conductive polymer layers to limit transfer of fuel reactants to catalysts of fuel cells to reduce reactant crossover

Science.gov (United States)

Stanis, Ronald J.; Lambert, Timothy N.

2016-12-06

An apparatus of an aspect includes a fuel cell catalyst layer. The fuel cell catalyst layer is operable to catalyze a reaction involving a fuel reactant. A fuel cell gas diffusion layer is coupled with the fuel cell catalyst layer. The fuel cell gas diffusion layer includes a porous electrically conductive material. The porous electrically conductive material is operable to allow the fuel reactant to transfer through the fuel cell gas diffusion layer to reach the fuel cell catalyst layer. The porous electrically conductive material is also operable to conduct electrons associated with the reaction through the fuel cell gas diffusion layer. An electrically conductive polymer material is coupled with the fuel cell gas diffusion layer. The electrically conductive polymer material is operable to limit transfer of the fuel reactant to the fuel cell catalyst layer.

Aqueous degradation kinetics of pharmaceutical drug diclofenac by photo catalysis using nano structured titania–zirconia composite catalyst

International Nuclear Information System (INIS)

Das, L.; Barodia, S. K.; Sengupta, S.; Basu, J. K.

2015-01-01

Diclofenac is an anti-inflammatory pharmaceutical drug and its presence in a trace amount in waste water makes severe environmental pollution. The degradation of diclofenac was investigated by a photo catalytic process in presence of ultra violet irradiation at room temperature using titania and titania-zirconia nano composite catalysts in a batch reactor. The composite catalyst was prepared by sol-gel method and characterized by X-ray diffraction, transmission electron microscopy as well as BET surface area analyzer. The effect of various process parameters such as catalyst loading, initial concentration of diclofenac and p H of the experimental solution was observed on the degradation of diclofenac. The titania-zirconia nano composites exhibited reasonably higher photo catalytic activity than that of anatase form of titania without zirconia. The maximum removal of diclofenac of about 92.41% was achieved using Zr/Ti mass ratio of 11.8 wt% composite catalyst. A rate equation was proposed for the degradation of diclofenac using the composite catalyst. The values of rate constant (kc) and adsorption equilibrium constant (K1) were found to vary with the catalyst content in the reaction mixture.

Catalyst Degradation in High Temperature Proton Exchange Membrane Fuel Cells Based on Acid Doped Polybenzimidazole Membranes

DEFF Research Database (Denmark)

Cleemann, Lars Nilausen; Buazar, F.; Li, Qingfeng

2013-01-01

and multi‐walled carbon nanotubes were used as supports for electrode catalysts and evaluated in accelerated durability tests under potential cycling at 150 °C. Measurements of open circuit voltage, area specific resistance and hydrogen permeation through the membrane were carried out, indicating little...... contribution of the membrane degradation to the performance losses during the potential cycling tests. As the major mechanism of the fuel cell performance degradation, the electrochemical active area of the cathodic catalysts showed a steady decrease in the cyclic voltammetric measurements, which was also......Degradation of carbon supported platinum catalysts is a major failure mode for the long term durability of high temperature proton exchange membrane fuel cells based on phosphoric acid doped polybenzimidazole membranes. With Vulcan carbon black as a reference, thermally treated carbon black...

Photo catalytic degradation of nitrobenzene using nanocrystalline TiO{sub 2} photo catalyst doped with Zn ions

Energy Technology Data Exchange (ETDEWEB)

Reynoso S, E. A.; Perez S, S.; Reyes C, A. P.; Castro R, C. L.; Felix N, R. M.; Lin H, S. W. [Instituto Tecnologico de Tijuana, Centro de Graduados e Investigacion, Apdo. Postal 1166, 22000 Tijuana, Baja California (Mexico); Paraguay D, F. [Centro de Investigacion en Materiales Avanzados, Apdo. Postal 311109, Chihuahua (Mexico); Alonso N, G. [UNAM, Centro de Nanociencias y Nanotecnologia, Carretera Tijuana-Ensenada Km 107, Apdo. Postal 356, 22800 Ensenada, Baja California (Mexico)

2013-07-01

Photo catalysis is a method widely used in the degradation of organic pollutants of the environment. The development of new materials is very important to improve the photo catalytic properties and to find new applications for TiO{sub 2} as a photo catalyst. In this article we reported the synthesis of a photo catalyst based on TiO{sub 2} doped with Zn{sup 2+} ions highly efficient in the degradation of nitrobenzene. The results of photo catalytic activity experiments showed that the Zn{sup 2+} doped TiO{sub 2} is more active that un-doped TiO{sub 2} catalyst with an efficiency of 99% for the nitrobenzene degradation at 120 min with an apparent rate constant of 35 x 10{sup -3} min{sup -1}. For the characterization of photo catalyst X-ray diffraction, transmission electron microscopy and Raman spectroscopy were used. (Author)

Modeling Low-Platinum-Loading Effects in Fuel-Cell Catalyst Layers

Energy Technology Data Exchange (ETDEWEB)

Yoon, Wonseok; Weber, Adam Z.

2011-01-01

The cathode catalyst layer within a proton-exchange-membrane fuel cell is the most complex and critical, yet least understood, layer within the cell. The exact method and equations for modeling this layer are still being revised and will be discussed in this paper, including a 0.8 reaction order, existence of Pt oxides, possible non-isopotential agglomerates, and the impact of a film resistance towards oxygen transport. While the former assumptions are relatively straightforward to understand and implement, the latter film resistance is shown to be critically important in explaining increased mass-transport limitations with low Pt-loading catalyst layers. Model results demonstrate agreement with experimental data that the increased oxygen flux and/or diffusion pathway through the film can substantially decrease performance. Also, some scale-up concepts from the agglomerate scale to the more macroscopic porous-electrode scale are discussed and the resulting optimization scenarios investigated.

Efficient photo-catalytic degradation of malachite green using nickel tungstate material as photo-catalyst.

Science.gov (United States)

Helaïli, N; Boudjamaa, A; Kebir, M; Bachari, K

2017-03-01

The present study focused on the evaluation of photo-catalytic and photo-electrochemical properties of the photo-catalyst based on nickel tungstate material prepared by a nitrate method through the degradation of malachite green (MG) dye's. The effect of catalyst loading and dye concentration was examined. Physico-chemical, optical, electrical, electrochemical, and photo-electrochemical properties of the prepared material were analyzed by X-ray diffraction (XRD), fourier transform-infrared spectroscopy (FTIR), BET analysis, optical reflectance diffuse (DR), scanning electron microscopy (SEM/EDX), electrical conductivity, cyclic voltammetry (CV), current intensity, mott-shottky, and nyquist. XRD revealed the formation of monoclinic structure with a small particle size. BET surface area of the sample was around 10 m 2 /g. The results show that the degradation of MG was more than 80%, achieved after 3 h of irradiation at pH 4.6 and with a catalyst loading of 75 mg. Also, it was found that the dye photo-degradation obeyed the pseudo-first order kinetic via Langmuir Hinshelwood model.

Degradation and Mineralization of Phenol Compounds with Goethite Catalyst and Mineralization Prediction Using Artificial Intelligence

Science.gov (United States)

Tisa, Farhana; Davoody, Meysam; Abdul Raman, Abdul Aziz; Daud, Wan Mohd Ashri Wan

2015-01-01

The efficiency of phenol degradation via Fenton reaction using mixture of heterogeneous goethite catalyst with homogeneous ferrous ion was analyzed as a function of three independent variables, initial concentration of phenol (60 to 100 mg /L), weight ratio of initial concentration of phenol to that of H2O2 (1: 6 to 1: 14) and, weight ratio of initial concentration of goethite catalyst to that of H2O2 (1: 0.3 to 1: 0.7). More than 90 % of phenol removal and more than 40% of TOC removal were achieved within 60 minutes of reaction. Two separate models were developed using artificial neural networks to predict degradation percentage by a combination of Fe3+ and Fe2+ catalyst. Five operational parameters were employed as inputs while phenol degradation and TOC removal were considered as outputs of the developed models. Satisfactory agreement was observed between testing data and the predicted values (R2 Phenol = 0.9214 and R2TOC= 0.9082). PMID:25849556

Degradation and mineralization of phenol compounds with goethite catalyst and mineralization prediction using artificial intelligence.

Directory of Open Access Journals (Sweden)

Farhana Tisa

Full Text Available The efficiency of phenol degradation via Fenton reaction using mixture of heterogeneous goethite catalyst with homogeneous ferrous ion was analyzed as a function of three independent variables, initial concentration of phenol (60 to 100 mg /L, weight ratio of initial concentration of phenol to that of H2O2 (1: 6 to 1: 14 and, weight ratio of initial concentration of goethite catalyst to that of H2O2 (1: 0.3 to 1: 0.7. More than 90 % of phenol removal and more than 40% of TOC removal were achieved within 60 minutes of reaction. Two separate models were developed using artificial neural networks to predict degradation percentage by a combination of Fe3+ and Fe2+ catalyst. Five operational parameters were employed as inputs while phenol degradation and TOC removal were considered as outputs of the developed models. Satisfactory agreement was observed between testing data and the predicted values (R2Phenol = 0.9214 and R2TOC= 0.9082.

The Experimental Measurement of Local and Bulk Oxygen Transport Resistances in the Catalyst Layer of Proton Exchange Membrane Fuel Cells.

Science.gov (United States)

Wang, Chao; Cheng, Xiaojing; Lu, Jiabin; Shen, Shuiyun; Yan, Xiaohui; Yin, Jiewei; Wei, Guanghua; Zhang, Junliang

2017-12-07

Remarkable progress has been made in reducing the cathodic Pt loading of PEMFCs; however, a huge performance loss appears at high current densities, indicating the existence of a large oxygen transport resistance associated with the ultralow Pt loading catalyst layer. To reduce the Pt loading without sacrificing cell performance, it is essential to illuminate the oxygen transport mechanism in the catalyst layer. Toward this goal, an experimental approach to measure the oxygen transport resistance in catalyst layers is proposed and realized for the first time in this study. The measuring approach involves a dual-layer catalyst layer design, which consists of a dummy catalyst layer and a practical catalyst layer, followed by changing the thickness of dummy layer to respectively quantify the local and bulk resistances via limiting current measurements combined with linear extrapolation. The experimental results clearly reveal that the local resistance dominates the total resistance in the catalyst layer.

A proposed agglomerate model for oxygen reduction in the catalyst layer of proton exchange membrane fuel cells

International Nuclear Information System (INIS)

Zhang, Xiaoxian; Gao, Yuan; Ostadi, Hossein; Jiang, Kyle; Chen, Rui

2014-01-01

Highlights: • We developed a new agglomerate model to describe oxygen reduction reaction. • We showed how to calculate the model parameters from catalyst layer structure. • We verified the agglomerate model. - Abstract: Oxygen diffusion and reduction in the catalyst layer of PEM fuel cell is an important process in fuel cell modelling, but models able to link the reduction rate to catalyst-layer structure are lack; this paper makes such an effort. We first link the average reduction rate over the agglomerate within a catalyst layer to a probability that an oxygen molecule, which is initially on the agglomerate surface, will enter and remain in the agglomerate at any time in the absence of any electrochemical reaction. We then propose a method to directly calculate distribution function of this probability and apply it to two catalyst layers with contrasting structures. A formula is proposed to describe these calculated distribution functions, from which the agglomerate model is derived. The model has two parameters and both can be independently calculated from catalyst layer structures. We verify the model by first showing that it is an improvement and able to reproduce what the spherical model describes, and then testing it against the average oxygen reductions directly calculated from pore-scale simulations of oxygen diffusion and reaction in the two catalyst layers. The proposed model is simple, but significant as it links the average oxygen reduction to catalyst layer structures, and its two parameters can be directly calculated rather than by calibration

CoFe2O4 magnetic nanoparticles as a highly active heterogeneous catalyst of oxone for the degradation of diclofenac in water

International Nuclear Information System (INIS)

Deng, Jing; Shao, Yisheng; Gao, Naiyun; Tan, Chaoqun; Zhou, Shiqing; Hu, Xuhao

2013-01-01

Highlights: • CoFe 2 O 4 MNPs tested as heterogeneous catalyst for the activation of oxone. • The catalytic performance was typically affected by several key operating parameters. • The catalyst exhibited good stability and easily recovered with excellent reusability. • Degradation pathway was proposed according to the results of LC-MS/MS analysis. -- Abstract: A magnetic nanoscaled catalyst cobalt ferrite (CoFe 2 O 4 ) was successfully prepared and used for the activation of oxone to generate sulfate radicals for the degradation of diclofenac. The catalyst was characterized by transmission electron microscopy, X-ray diffractometry, Fourier transform infrared spectroscopy and vibrating sample magnetometer. The effects of calcination temperature, initial pH, catalyst and oxone dosage on the degradation efficiency were investigated. Results demonstrated that CoFe 2 O 4 -300 exhibited the best catalytic performance and almost complete removal of diclofenac was obtained in 15 min. The degradation efficiency increased with initial pH decreasing in the pH range of 5–9. The increase of catalyst and oxone dosage both had the positive effect on the degradation of diclofenac. Moreover, CoFe 2 O 4 could retain high degradation efficiency even after being reused for five cycles. Finally, the major diclofenac degradation intermediates were identified and the primary degradation pathways were proposed

Fabrication and characterization of anode catalyst layers with structural variations for DMFC

Science.gov (United States)

Wang, Dazhi; Shi, Peng; Zhou, Peng; Mao, Qing; Liang, Junsheng; Wang, Suli; Li, Yang; Ren, Tongqun; Sun, Gongquan

2018-04-01

In this work, the electrohydrodynamic jet (E-Jet) Layer-by-Layer (LbL) deposition technique was employed to produce anode catalyst layer (CL) structure for direct methanol fuel cells (DMFC). The CLs with different thickness and porosity were fabricated with the control of the E-Jet deposition parameters. Then, the deposited anode CLs with structural variations were assembled to membrane electrode assemblies (MEAs). The results showed that the anode CL with higher porosity contributed higher dispersed catalyst, which further induced greater electrochemical active surface area (ESA) and higher performance. At optimized working condition the anode CL with high-dispersed catalyst of was produced using the E-Jet LbL deposition technique. It was observed that the peak power density is 72.8 mW cm‑2 for the cell having a porosity of 0.63, which has an increase of about 33% after modification of the CL structure.

Photocatalytic degradation of nicotine in an aqueous solution using unconventional supported catalysts and commercial ZnO/TiO{sub 2} under ultraviolet radiation

Energy Technology Data Exchange (ETDEWEB)

Franco, Marcela Andrea Espina de, E-mail: marcela.eq@gmail.com; Silva, William Leonardo da; Bagnara, Mônica; Lansarin, Marla Azário; Zimnoch dos Santos, João Henrique

2014-10-01

Nicotine, a highly toxic alkaloid, has been detected in effluents, surface and groundwater and even bottled mineral water. The present work studied the photocatalytic degradation of nicotine in aqueous solution, under ultraviolet irradiation. The experiments were carried out using commercial (ZnO, TiO{sub 2}) and non-conventional catalysts, which were prepared from industrial and laboratory waste. Two experimental designs (CCD) were performed for both commercial catalysts, and initial nicotine concentration, catalyst concentration and initial solution pH effects were studied. Then, the synthesized catalysts were tested under the optimal conditions which were found through CCDs. Using commercial catalysts, about 98% of the alkaloid was degraded by ZnO, and 88% by TiO{sub 2}, in 1 h. Among the non-conventional catalysts, the highest photocatalytic degradation (44%) was achieved using the catalyst prepared from a petrochemical industry residue. - Highlights: • The photocatalytic degradation of nicotine was studied under UV irradiation. • Commercial catalysts ZnO and TiO{sub 2} were tested using two central composite designs. • Initial nicotine concentration, catalyst concentration and pH were evaluated. • Catalysts were prepared using chemical wastes and tested at the best conditions.

A mathematical model and optimization of the cathode catalyst layer structure in PEM fuel cells

International Nuclear Information System (INIS)

Wang Qianpu; Song Datong; Navessin, Titichai; Holdcroft, Steven; Liu Zhongsheng

2004-01-01

A spherical flooded-agglomerate model for the cathode catalyst layer of a proton exchange membrane fuel cell, which includes the kinetics of oxygen reduction, at the catalyst vertical bar electrolyte interface, proton transport through the polymer electrolyte network, the oxygen diffusion through gas pore, and the dissolved oxygen diffusion through electrolyte, is considered. Analytical and numerical solutions are obtained in various control regimes. These are the limits of (i) oxygen diffusion control (ii) proton conductivity control, and (iii) mixture control. The structure and material parameters, such as porosity, agglomerate size, catalyst layer thickness and proton conductivity, on the performance are investigated under these limits. The model could help to characterize the system properties and operation modes, and to optimize catalyst layer design

Studies on Nano-Engineered TiO2 Photo Catalyst for Effective Degradation of Dye

Science.gov (United States)

Sowmya, S. R.; Madhu, G. M.; Hashir, Mohammed

2018-02-01

All Heterogeneous photo catalysis employing efficient photo-catalyst is the advanced dye degradation technology for the purification of textile effluent. The present work focuses on Congo red dye degradation employing synthesized Ag doped TiO2 nanoparticles as photocatalyst which is characterized using SEM, XRD and FTIR. Studies are conducted to study the effect of various parameters such as initial dye concentration, catalyst loading and pH of solution. Ag Doped TiO2 photocatalyst improve the efficacy of TiO2 by reducing high band gap and electron hole recombination of TiO2. The reaction kinetics is analyzed and the process is found to follow pseudo first order kinetics.

Degradation of atenolol via heterogeneous activation of persulfate by using BiOCl@Fe3O4 catalyst under simulated solar light irradiation.

Science.gov (United States)

Shi, Yahong; Chen, Hongche; Wu, Yanlin; Dong, Wenbo

2018-01-01

Efficient oxidative degradation of pharmaceutical pollutants in aquatic environments is of great importance. This study used magnetic BiOCl@Fe 3 O 4 catalyst to activate persulfate (PS) under simulated solar light irradiation. This degradation system was evaluated using atenolol (ATL) as target pollutant. Four reactive species were identified in the sunlight/BiOCl@Fe 3 O 4 /PS system. The decreasing order of the contribution of each reactive species on ATL degradation was as follows: h +  ≈ HO ·  > O 2 ·-  > SO 4 ·- . pH significantly influenced ATL degradation, and an acidic condition favored the reaction. High degradation efficiencies were obtained at pH 2.3-5.5. ATL degradation rate increased with increased catalyst and PS contents. Moreover, ATL mineralization was higher in the sunlight/BiOCl@Fe 3 O 4 /PS system than in the sunlight/BiOCl@Fe 3 O 4 or sunlight/PS system. Nine possible intermediate products were identified through LC-MS analysis, and a degradation pathway for ATL was proposed. The BiOCl@Fe 3 O 4 nanomagnetic composite catalyst was synthesized in this work. This catalyst was easily separated and recovered from a treated solution by using a magnet, and it demonstrated a high catalytic activity. Increased amount of the BiOCl@Fe 3 O 4 catalyst obviously accelerated the efficiency of ATL degradation, and the reusability of the catalyst allowed the addition of a large dosage of BiOCl@Fe 3 O 4 to improve the degradation efficiency.

The enhanced photoactivity of nanosized Bi2WO6 catalyst for the degradation of 4-chlorophenol

International Nuclear Information System (INIS)

Fu Hongbo; Yao Wenqing; Zhang Liwu; Zhu Yongfa

2008-01-01

Nanosized Bi 2 WO 6 catalyst exhibited the enhanced photoactivity for the degradation of 4-chlorophenol (4-CP) under visible irradiation compared to the sample prepared by high-temperature solid reaction. The photoactivity of the catalyst was sensitive to pH variation of the suspension. Nanosized Bi 2 WO 6 catalyst showed the highest activity at pH 7.2. The photodegradation of 4-CP by nanosized Bi 2 WO 6 catalyst followed a pseudo-first-order reaction. After three recycling runs for the photodegradation of 4-CP, the activity of the catalyst did not show any significant loss, suggesting that the catalyst was stable under visible irradiation

Synthesis of Pt@TiO2@CNTs Hierarchical Structure Catalyst by Atomic Layer Deposition and Their Photocatalytic and Photoelectrochemical Activity.

Science.gov (United States)

Liao, Shih-Yun; Yang, Ya-Chu; Huang, Sheng-Hsin; Gan, Jon-Yiew

2017-04-29

Pt@TiO2@CNTs hierarchical structures were prepared by first functionalizing carbon nanotubes (CNTs) with nitric acid at 140 °C. Coating of TiO2 particles on the CNTs at 300 °C was then conducted by atomic layer deposition (ALD). After the TiO2@CNTs structure was fabricated, Pt particles were deposited on the TiO2 surface as co-catalyst by plasma-enhanced ALD. The saturated deposition rates of TiO2 on a-CNTs were 1.5 Å/cycle and 0.4 Å/cycle for substrate-enhanced process and linear process, respectively. The saturated deposition rate of Pt on TiO2 was 0.39 Å/cycle. The photocatalytic activities of Pt@TiO2@CNTs hierarchical structures were higher than those without Pt co-catalyst. The particle size of Pt on TiO2@CNTs was a key factor to determine the efficiency of methylene blue (MB) degradation. The Pt@TiO2@CNTs of 2.41 ± 0.27 nm exhibited the best efficiency of MB degradation.

Electroplating sludge derived zinc-ferrite catalyst for the efficient photo-Fenton degradation of dye.

Science.gov (United States)

Cao, Zhenbang; Zhang, Jia; Zhou, Jizhi; Ruan, Xiuxiu; Chen, Dan; Liu, Jianyong; Liu, Qiang; Qian, Guangren

2017-05-15

A zinc-dominant ferrite catalyst for efficient degradation of organic dye was prepared by the calcination of electroplating sludge (ES). Characterizations indicated that zinc ferrite (ZnFe 2 O 4 ) coexisted with Fe 2 O 3 structure was the predominant phase in the calcined electroplating sludge (CES). CES displayed a high decolorization ratio (88.3%) of methylene blue (MB) in the presence of H 2 O 2 combined with UV irradiation. The high efficiency could be ascribed to the photocatalytic process induced by ZnFe 2 O 4 and the photo-Fenton dye degradation by ferrous content, and a small amount of Al and Mg in the sludge might also contribute to the catalysis. Moreover, the degradation capability of dye by CES was supported by the synthetic ZnFe 2 O 4 with different Zn to Fe molar ratio (n(Zn): n(Fe)), as 84.81%-86.83% of dye was removed with n(Zn): n(Fe) ranged from 1:0.5 to 1:3. All synthetic ferrite samples in the simulation achieved adjacent equilibrium decolorization ratio, the flexible proportioning of divalent metal ions (M 2+ ) to trivalent metal ions (M 3+ ) applied in the synthesis indicated that the catalyst has a high availability. Therefore, an efficacious catalyst for the degradation of dye can potentially be derived from heavy metal-containing ES, it's a novel approach for the reutilization of ES. Copyright © 2016 Elsevier Ltd. All rights reserved.

CoFe{sub 2}O{sub 4} magnetic nanoparticles as a highly active heterogeneous catalyst of oxone for the degradation of diclofenac in water

Energy Technology Data Exchange (ETDEWEB)

Deng, Jing [State Key Laboratory of Pollution Control Reuse, Tongji University, Shanghai 200092 (China); Shao, Yisheng, E-mail: shaoyisheng2011@163.com [State Key Laboratory of Pollution Control Reuse, Tongji University, Shanghai 200092 (China); China Academy of Urban Planning and Design, Beijing 100037 (China); Gao, Naiyun; Tan, Chaoqun; Zhou, Shiqing; Hu, Xuhao [State Key Laboratory of Pollution Control Reuse, Tongji University, Shanghai 200092 (China)

2013-11-15

Highlights: • CoFe{sub 2}O{sub 4} MNPs tested as heterogeneous catalyst for the activation of oxone. • The catalytic performance was typically affected by several key operating parameters. • The catalyst exhibited good stability and easily recovered with excellent reusability. • Degradation pathway was proposed according to the results of LC-MS/MS analysis. -- Abstract: A magnetic nanoscaled catalyst cobalt ferrite (CoFe{sub 2}O{sub 4}) was successfully prepared and used for the activation of oxone to generate sulfate radicals for the degradation of diclofenac. The catalyst was characterized by transmission electron microscopy, X-ray diffractometry, Fourier transform infrared spectroscopy and vibrating sample magnetometer. The effects of calcination temperature, initial pH, catalyst and oxone dosage on the degradation efficiency were investigated. Results demonstrated that CoFe{sub 2}O{sub 4}-300 exhibited the best catalytic performance and almost complete removal of diclofenac was obtained in 15 min. The degradation efficiency increased with initial pH decreasing in the pH range of 5–9. The increase of catalyst and oxone dosage both had the positive effect on the degradation of diclofenac. Moreover, CoFe{sub 2}O{sub 4} could retain high degradation efficiency even after being reused for five cycles. Finally, the major diclofenac degradation intermediates were identified and the primary degradation pathways were proposed.

Optimization of Acid Orange 7 Degradation in Heterogeneous Fenton-like Reaction Using Fe3-xCoxO4 Catalyst

Science.gov (United States)

Ibrahim, M. Z.; Alrozi, R.; Zubir, N. A.; Bashah, N. A.; Ali, S. A. Md; Ibrahim, N.

2018-05-01

The oxidation process such as heterogeneous Fenton and/or Fenton-like reactions is considered as an effective and efficient method for treatment of dye degradation. In this study, the degradation of Acid Orange 7 (AO7) was investigated by using Fe3-xCoxO4 as a heterogeneous Fenton-like catalyst. Response surface methodology (RSM) was used to optimize the operational parameters condition and the interaction of two or more parameters. The parameter studies were catalyst dosage (X1 ), pH (X2 ) and H2O2 concentration (X3 ) towards AO7 degradation. Based on analysis of variance (ANOVA), the derived quadratic polynomial model was significant whereby the predicted values matched the experimental values with regression coefficient of R2 = 0.9399. The optimum condition for AO7 degradation was obtained at catalyst dosage of 0.84 g/L, pH of 3 and H2O2 concentration of 46.70 mM which resulted in 86.30% removal of AO7 dye. These findings present new insights into the influence of operational parameters in the heterogeneous Fenton-like oxidation of AO7 using Fe3-xCoxO4 catalyst.

Photocatalytic degradation of Maxilon C.I. basic dye using CS/CoFe_2O_4/GONCs as a heterogeneous photo-Fenton catalyst prepared by gamma irradiation

International Nuclear Information System (INIS)

Al-Kahtani, Abdullah A.; Abou Taleb, Manal F.

2016-01-01

Highlights: • CS/CF/GONCs were synthesized via γ-irradiation and used as a heterogeneous photo-Fenton catalyst. • It can degrade Maxilon C.I. basic dye under sunlight irradiation. • A possible degradation pathway of Maxilon C.I. Basic was proposed. • The degradation of Maxilon follows pseudo-first-order kinetics. • The catalyst can be separated by an external magnetic field. • Cyclic degradation tests show the catalyst is highly active, stable and recoverable. - Abstract: CS/CF/GONCs were synthesized via gamma irradiation cross-linking method with the aid of sonication. The nanocomposites exhibited a photo-Fenton catalytic feature for the degradation of Maxilon C.I. basic dye in aqueous medium using sunlight. The effects of pH, H_2O_2 concentration, and dosage of the catalyst, on the degradation rates of the dyes were examined. The optimal degradation rate was reached with 10 mM H_2O_2 at pH 9.5. It was verified that the Maxilon C.I. basic dye degradation rate fits a pseudo-first-order kinetics for different initial concentrations of Maxilon C.I. dye. Fourth cyclic tests for Maxilon C.I. degradation showed that the magnetic catalyst was very stable, recoverable, highly active, and easy to separate using an external magnet. Hence, this magnetic catalyst has potential use in organic pollutant removal.

Thermal degradation of Shredded Oil Palm Empty Fruit Bunches (SOPEFB) embedded with Cobalt catalyst by Thermogravimetric Analysis (TGA)

Science.gov (United States)

Alias, R.; Hamid, N. H.; Jaapar, J.; Musa, M.; Alwi, H.; Halim, K. H. Ku

2018-03-01

Thermal behavior and decomposition kinetics of shredded oil palm empty fruit bunches (SOPEFB) were investigated in this study by using thermogravimetric analysis (TGA). The SOPEFB were analyzed under conditions of temperature 30 °C to 900 °C with nitrogen gas flow at 50 ml/min. The SOPEFB were embedded with cobalt (II) nitrate solution with concentration 5%, 10%, 15% and 20%. The TG/DTG curves shows the degradation behavior of SOPEFB following with char production for each heating rate and each concentration of cobalt catalyst. Thermal degradation occurred in three phases, water drying phase, decomposition of hemicellulose and cellulose phase, and lignin decomposition phase. The kinetic equation with relevant parameters described the activation energy required for thermal degradation at the temperature regions of 200 °C to 350 °C. Activation energy (E) for different heating rate with SOPEFB embedded with different concentration of cobalt catalyst showing that the lowest E required was at SOPEFB with 20% concentration of cobalt catalyst..

Effect of the solvent in the catalyst ink preparation on the properties and performance of unsupported PtRu catalyst layers in direct methanol fuel cells

International Nuclear Information System (INIS)

Alcaide, Francisco; Álvarez, Garbiñe; Cabot, Pere L.; Genova-Koleva, Radostina; Grande, Hans-Jürgen; Miguel, Oscar

2017-01-01

The effect of the organic solvent polarity on the properties of unsupported PtRu catalyst inks and on the performance of the catalyst layers prepared with them for the methanol electrooxidation, has been studied. The light scattering results indicate that the PtRu-Nafion ® aggregates in the inks prepared with n-butyl acetate (NBA) are larger than those prepared with 2-propanol (IPA). The lower polarity of the former favours the aggregation of Nafion ® and nanoparticles. The electron microscopy images and porosimetry measurements of the catalyst layers show that the secondary pore volume between the agglomerates is larger for NBA. The linear sweep voltammetry and eis results for the methanol electrooxidation in the three-electrode cell denote the higher active surface area for NBA and comparable specific oxidation rates of the intermediates in both catalysts layers. The current densities for PtRu anode catalyst layers in single DMFC are higher when the solvent is NBA, the mass transport limitations being much more apparent with IPA. The adapted transmission line equivalent circuit to interpret the impedance results in single DMFC indicates that the proton resistance for NBA is significantly lower than for IPA, thus suggesting that the greater number of accessible active sites for methanol oxidation in the former are well connected to the Nafion ® ionomers and easier transported to the membrane.

Silica-Supported Co3O4 Nanoparticles as a Recyclable Catalyst for Rapid Degradation of Azodye

Directory of Open Access Journals (Sweden)

Ali Baghban

2016-10-01

Full Text Available In this paper, silica nanoparticles with particle size of ~ 10-20 nm were selected as a support for the synthesis of Co3O4 nanoparticles by impregnation of silica nanoparticles in solution of Co(II in a specific concentrations and then calcination to 800 oC. This nanocomposite was then, used as a catalyst for oxidative degradation of methyl orange (MO with ammonium persulfate in aqueous media. Effect of pH, temperature, contact time, amount of oxidant and catalyst were studied in the presence of manuscript. Scanning electron microscope (SEM, electron dispersive spectroscopy (EDS, FT-IR, and ICP-AES analyses were used for analysis of silica-supported Co3O4 (Co3O4/SiO2. Treating MO with ammonium persulfate in the presence of Co3O4/SiO2 led to complete degradation of MO under the optimized conditions. Also, the catalyst exhibited recyclability at least over 10 consecutive runs. Copyright © 2016 BCREC GROUP. All rights reserved Received: 12nd December 2015; Revised: 27th January 2016; Accepted: 27th January 2016 How to Cite: Baghban, A., Doustkhah, E., Rostamnia, S., Aghbash, K.O. (2016. Silica-Supported Co3O4 Nanoparticles as a Recyclable Catalyst for Rapid Degradation of Azodye. Bulletin of Chemical Reaction Engineering & Catalysis, 11 (3: 284-291 (doi:10.9767/bcrec.11.3.568.284-291 Permalink/DOI: http://doi.org/10.9767/bcrec.11.3.568.284-291

Oxidative Debromination and Degradation of Tetrabromo-bisphenol A by a Functionalized Silica-Supported Iron(III-tetrakis(p-sulfonatophenylporphyrin Catalyst

Directory of Open Access Journals (Sweden)

Masami Fukushima

2013-05-01

Full Text Available Tetrabromobisphenol A (TBBPA, a commonly used brominated flame retardant, also functions as an endocrine disruptor. Thus, the degradation of TBBPA has attracted considerable interest among the scientific community. Iron(III-porphyrin complexes are generally regarded as “green” catalysts and have been reported to catalyze the efficient degradation and dehalogenation of halogenated phenols in environmental wastewaters. However, they are quickly deactivated due to self-degradation in the presence of an oxygen donor, such as KHSO5. In the present study, an iron(III-tetrakis (p-sulfonatophenyl-porphyrin (FeTPPS was immobilized on imidazole-modified silica (FeTPPS/IPS via coordination of the Fe(III with the nitrogen atom in imidazole to suppress self-degradation and thus enhance the catalyst reusability. The oxidative degradation and debromination of TBBPA and the influence of humic acid (HA, a major component in leachates, on the oxidation of TBBPA was investigated. More than 95% of the TBBPA was degraded in the pH range from 3 to 8 in the absence of HA, while the optimal pH for the reaction was at pH 8 in the presence of HA. Although the rate of degradation was decreased in the presence of HA, over 95% of the TBBPA was degraded within 12 h in the presence of 28 mg-C L−1 of HA. At pH 8, the FeTPPS/IPS catalyst could be reused up to 10 times without any detectable loss of activity for TBBPA for degradation and debromination, even in the presence of HA.

Investigation on the sonocatalytic degradation of nitrobenzene using heterogeneous nanostructured catalysts in absence and presence of surfactant

Directory of Open Access Journals (Sweden)

F.Z. Yehia

2015-09-01

The potential degradation feasibility for NB in US/nano metal oxide (series I and or series II/H2O2 systems was measured by GC analysis at regular time intervals. Otherwise, some operational parameters such as ultrasonic irradiation time, solution pH value, H2O2 concentration, different weights of the nano-sized catalysts, NB concentration, leaching of the nano-sized catalysts, and reaction kinetics had been examined. It was found that H2O2 oxidant can effectively assist the sonocatalytic degradation of NB in the presence of nano-sized oxides (series I and with more efficiency in the presence of nano-sized oxides (series II, and the effect of efficiency in degradation was changed in the order of (Fe2O3 > CuO > NiO > Co3O4. Therefore, oxides prepared in micellar solution were found to upgrade the economic aspect of NB degradation.

Silver-Copper Nanoalloy Catalyst Layer for Bifunctional Air Electrodes in Alkaline Media.

Science.gov (United States)

Wu, Xiaoqiang; Chen, Fuyi; Jin, Yachao; Zhang, Nan; Johnston, Roy L

2015-08-19

A carbon-free and binder-free catalyst layer composed of a Ag-Cu nanoalloy on Ni foam was used as the air cathode in a zinc-air battery for the first time. The Ag-Cu catalyst was prepared using pulsed laser deposition. The structures of the catalysts were found to consist of crystalline Ag-Cu nanoalloy particles with an average size of 2.58 nm embedded in amorphous Cu films. As observed in the X-ray photoelectron spectra, the Ag 3d core levels shifted to higher binding energies, whereas the Cu 2p core levels shifted to lower binding energies, indicating alloying of the silver and copper. Rotating disk electrode measurements indicated that the oxygen reduction reaction (ORR) proceeded through a four-electron pathway on the Ag50Cu50 and Ag90Cu10 nanoalloy catalysts in alkaline solution. Moreover, the catalytic activity of Ag50Cu50 in the ORR is more efficient than that of Ag90Cu10. By performing charge and discharge cycling measurements, the Ag50Cu50 catalyst layer was confirmed to have a maximum power density of approximately 86.3 mW cm(-2) and an acceptable cell voltage at 0.863 V for current densities up to 100 mA cm(-2) in primary zinc-air batteries. In addition, a round-trip efficiency of approximately 50% at a current density of 20 mA cm(-2) was also obtained in the test.

Photocatalytic degradation of Maxilon C.I. basic dye using CS/CoFe{sub 2}O{sub 4}/GONCs as a heterogeneous photo-Fenton catalyst prepared by gamma irradiation

Energy Technology Data Exchange (ETDEWEB)

Al-Kahtani, Abdullah A. [Chemistry Department, College of Science, King Saud University, P. O. Box 2455, Riyadh 11451 (Saudi Arabia); Pharmaceutical Chemistry Department, College of Pharmacy, Prince Sattam Bin Abdulaziz University, P. O. Box 173, Alkharj 11942 (Saudi Arabia); Abou Taleb, Manal F., E-mail: abutalib_m@yahoo.com [Chemistry Department, College of Science and Humanities, Prince Sattam Bin Abdulaziz University, P. O. Box 173, Alkharj 11942 (Saudi Arabia); Polymer Department National Center for Radiation Research and Technology, Nasr city, Cairo (Egypt)

2016-05-15

Highlights: • CS/CF/GONCs were synthesized via γ-irradiation and used as a heterogeneous photo-Fenton catalyst. • It can degrade Maxilon C.I. basic dye under sunlight irradiation. • A possible degradation pathway of Maxilon C.I. Basic was proposed. • The degradation of Maxilon follows pseudo-first-order kinetics. • The catalyst can be separated by an external magnetic field. • Cyclic degradation tests show the catalyst is highly active, stable and recoverable. - Abstract: CS/CF/GONCs were synthesized via gamma irradiation cross-linking method with the aid of sonication. The nanocomposites exhibited a photo-Fenton catalytic feature for the degradation of Maxilon C.I. basic dye in aqueous medium using sunlight. The effects of pH, H{sub 2}O{sub 2} concentration, and dosage of the catalyst, on the degradation rates of the dyes were examined. The optimal degradation rate was reached with 10 mM H{sub 2}O{sub 2} at pH 9.5. It was verified that the Maxilon C.I. basic dye degradation rate fits a pseudo-first-order kinetics for different initial concentrations of Maxilon C.I. dye. Fourth cyclic tests for Maxilon C.I. degradation showed that the magnetic catalyst was very stable, recoverable, highly active, and easy to separate using an external magnet. Hence, this magnetic catalyst has potential use in organic pollutant removal.

Effect of the prominent catalyst layer surface on reactant gas transport and cell performance at the cathodic side of a PEMFC

International Nuclear Information System (INIS)

Perng, Shiang-Wuu; Wu, Horng-Wen

2010-01-01

The cell performance enhancement of a proton exchange membrane fuel cell (PEMFC) has been numerically investigated with the prominence-like form catalyst layer surface of the same composition at the cathodic half-cell of a PEMFC. The geometries of the prominence-like form catalyst layer surface are assigned as one prominence, three prominences, and five prominences catalyst layer surfaces with constant distance between two prominences in the same gas diffusion layer (GDL) for the purpose of investigating the cell performance. To confine the current investigation to two-dimensional incompressible flows, we assume that the fluid flow is laminar with a low Reynolds number 15. The results indicate that the prominence-like form catalyst layer surface can effectively enhance the local cell performance of a PEMFC.

Enhanced performance of proton exchange membrane fuel cell by introducing nitrogen-doped CNTs in both catalyst layer and gas diffusion layer

CSIR Research Space (South Africa)

Hou, S

2017-11-01

Full Text Available The performance of the proton exchange membrane fuel cell (PEMFC) is significantly improved through introducing nitrogen-doped carbon nanotubes (NCNTs) into the catalyst layer (CL) and microporous layer (MPL) of the membrane electrode assembly (MEA...

Fuel cell catalyst degradation

DEFF Research Database (Denmark)

Arenz, Matthias; Zana, Alessandro

2016-01-01

Fuel cells are an important piece in our quest for a sustainable energy supply. Although there are several different types of fuel cells, the by far most popular is the proton exchange membrane fuel cell (PEMFC). Among its many favorable properties are a short start up time and a high power density...... increasing focus. Activity of the catalyst is important, but stability is essential. In the presented perspective paper, we review recent efforts to investigate fuel cell catalysts ex-situ in electrochemical half-cell measurements. Due to the amount of different studies, this review has no intention to give...

Thermally oxidized aluminum as catalyst-support layer for vertically aligned single-walled carbon nanotube growth using ethanol

Energy Technology Data Exchange (ETDEWEB)

Azam, Mohd Asyadi, E-mail: asyadi@jaist.ac.jp [School of Materials Science, Japan Advanced Institute of Science and Technology (JAIST), 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan); Fujiwara, Akihiko [Research and Utilization Division, Japan Synchrotron Radiation Research Institute (JASRI), 1-1-1, Kouto, Sayo-cho, Sayo, Hyogo 679-5198 (Japan); Shimoda, Tatsuya [School of Materials Science, Japan Advanced Institute of Science and Technology (JAIST), 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan)

2011-11-01

Characteristics and role of Al oxide (Al-O) films used as catalyst-support layer for vertical growth of single-walled carbon nanotubes (SWCNTs) were studied. EB-deposited Al films (20 nm) were thermally oxidized at 400 deg. C (10 min, static air) to produce the most appropriate surface structure of Al-O. Al-O catalyst-support layers were characterized using various analytical measurements, i.e., atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and spectroscopy ellipsometry (SE). The thermally oxidized Al-O has a highly roughened surface, and also has the most suitable surface chemical states compared to other type of Al-O support layers. We suggest that the surface of thermally oxidized Al-O characterized in this work enhanced Co catalyst activity to promote the vertically aligned SWCNT growth.

Degradation of 2,4-dichlorophenol using combined approach based on ultrasound, ozone and catalyst.

Science.gov (United States)

Barik, Arati J; Gogate, Parag R

2017-05-01

The present work investigates the application of ultrasound and ozone operated individually and in combination with catalyst (ZnO and CuO) for establishing the possible synergistic effects for the degradation of 2,4-dichlorophenol. The dependency of extent of degradation on the operating parameters like temperature (over the range of 30-36°C), initial pH (3-9), catalyst as ZnO (loading of 0.025-0.15g/L) and CuO (loading of 0.02-0.1g/L) and initial concentration of 2,4-DCP (20-50ppm) has been established to maximize the efficacy of ultrasound (US) induced degradation. Using only US, the maximum degradation of 2,4-DCP obtained was 28.85% under optimized conditions of initial concentration as 20ppm, pH of 5 and temperature of 34°C. Study of effect of ozone flow rate for approach of only ozone revealed that maximum degradation was obtained at 400mg/h ozone flow rate. The combined approaches such as US+O 3 , US+ZnO, US+CuO, O 3 +ZnO, O 3 +CuO, US+O 3 +ZnO and US+O 3 +CuO have been subsequently investigated under optimized conditions and observed to be more efficient as compared to individual approaches. The maximum extent of degradation for the combined operation of US+O 3 (400mg/h)+ZnO (0.1g/L) and US+O 3 (400mg/h)+CuO (0.08g/L) has been obtained as 95.66% and 97.03% respectively. The degradation products of 2,4-DCP have been identified using GC-MS analysis and the toxicity analysis has also been performed based on the anti-microbial activity test (agar-well diffusion method) for the different treatment strategies. The present work has conclusively established that the combined approach of US+O 3 +CuO was the most efficient treatment scheme resulting in near complete degradation of 2,4-DCP with production of less toxic intermediates. Copyright © 2016 Elsevier B.V. All rights reserved.

Optical characteristics of silicon nanowires grown from tin catalyst layers on silicon coated glass

KAUST Repository

Ball, Jeremy

2012-08-20

The optical characteristics of silicon nanowires grown on Si layers on glass have been modeled using the FDTD (Finite Difference Time Domain) technique and compared with experimental results. The wires were grown by the VLS (vapour-liquid-solid) method using Sn catalyst layers and exhibit a conical shape. The resulting measured and modeled absorption, reflectance and transmittance spectra have been investigated as a function of the thickness of the underlying Si layer and the initial catalyst layer, the latter having a strong influence on wire density. High levels of absorption (>90% in the visible wavelength range) and good agreement between the modeling and experiment have been observed when the nanowires have a relatively high density of ∼4 wires/μ m2. The experimental and modeled results diverge for samples with a lower density of wire growth. The results are discussed along with some implications for solar cell fabrication. © 2012 Optical Society of America.

Optical characteristics of silicon nanowires grown from tin catalyst layers on silicon coated glass

KAUST Repository

Ball, Jeremy; Centeno, Anthony; Mendis, Budhika G.; Reehal, H. S.; Alford, Neil

2012-01-01

The optical characteristics of silicon nanowires grown on Si layers on glass have been modeled using the FDTD (Finite Difference Time Domain) technique and compared with experimental results. The wires were grown by the VLS (vapour-liquid-solid) method using Sn catalyst layers and exhibit a conical shape. The resulting measured and modeled absorption, reflectance and transmittance spectra have been investigated as a function of the thickness of the underlying Si layer and the initial catalyst layer, the latter having a strong influence on wire density. High levels of absorption (>90% in the visible wavelength range) and good agreement between the modeling and experiment have been observed when the nanowires have a relatively high density of ∼4 wires/μ m2. The experimental and modeled results diverge for samples with a lower density of wire growth. The results are discussed along with some implications for solar cell fabrication. © 2012 Optical Society of America.

Effect of the thickness of the anode electrode catalyst layers on the performance in direct methanol fuel cells

Science.gov (United States)

Glass, Dean E.; Olah, George A.; Prakash, G. K. Surya

2017-06-01

For the large scale fuel cell manufacture, the catalyst loading and layer thickness are critical factors affecting the performance and cost of membrane electrode assemblies (MEAs). The influence of catalyst layer thicknesses at the anode of a PEM based direct methanol fuel cell (DMFC) has been investigated. Catalysts were applied with the drawdown method with varied thicknesses ranging from 1 mil to 8 mils (1 mil = 25.4 μm) with a Pt/Ru anode loading of 0.25 mg cm-2 to 2.0 mg cm-2. The MEAs with the thicker individual layers (8 mils and 4 mils) performed better overall compared to the those with the thinner layers (1 mil and painted). The peak power densities for the different loading levels followed an exponential decrease of Pt/Ru utilization at the higher loading levels. The highest power density achieved was 49 mW cm-2 with the 4 mil layers at 2.0 mg cm-2 catalyst loading whereas the highest normalized power density was 116 mW mg-1 with the 8 mil layers at 0.25 mg cm-2 loading. The 8 mil drawdowns displayed a 50% and 23% increase in normalized power density compared to the 1 mil drawdowns at 0.25 mg cm-2 and 0.5 mg cm-2 loadings, respectively.

Solid Catalyst with Ionic Liquid Layer (SCILL). A concept to improve the selectivity of selective hydrogenations

Energy Technology Data Exchange (ETDEWEB)

Jess, A.; Korth, W. [Bayreuth Univ. (Germany). Chair of Chemical Engineering

2011-07-01

Catalytic hydrogenations are important for refinery processes, petrochemical applications as well as for numerous processes of the fine chemicals industry. In some cases, hydrogenations consist of a sequence of consecutive reactions, and the desired product is the intermediate. An important goal is then a high yield and selectivity to the intermediate, if possible at a high conversion degree. The selectivity to an intermediate primarily depends on the chemical nature of the catalyst, but may also be influenced by diffusion processes. Ionic liquids (ILs) are low melting salts (< 100 C) and represent a promising solvent class. This paper focuses on the concept of a Solid Catalyst with Ionic Liquid Layer (SCILL), where the solid catalyst is coated with a thin IL layer to improve the selectivity. (orig.)

Mechanisms and modeling development of water transport/phase change in catalyst layers of portion exchange membrane fuel cells

Energy Technology Data Exchange (ETDEWEB)

Xiao, Yexiang [Dept. of Thermal Engineering, Tsinghua University Beijing (China)], email: Yexiang.Xiao@energy.lth.se; Yuan, Jinliang; Sunden, Bengt [Dept. of Energy Sciences, Faculty of Engineering, Lund University (Sweden)], email: Jinliang.yuan@energy.lth.se, email: bengt.sunden@energy.lth.se

2011-07-01

Research on proton exchange membrane fuel cells has shown that incorporation of nanosized catalysts can effectively increase active areas and catalyst activity and make a great contribution to development in performance and catalyst utilization. Multiphase transport processes are as significant and complicated as water generation/transfer processes which occur in nano-structured catalyst layers. A review project has been launched aimed at gaining a comprehensive understanding of the mechanisms of water generation or transport phenomena. It covers catalytic reactions and water-phase change within the catalyst layers. The review proceeds in three main stages: Firstly, it characterizes and reconstructs the nano/micro-structured pores and solid-phases; secondly, it emphasises the importance of sensitive and consistent analysis of various water-phase change and transport schemes; and thirdly, it recommends development of microscopic models for multi-phase transport processes in the pores and the solid phases.

Low irradiance photocatalytic degradation of toluene in air by screen-printed titanium dioxide layers

International Nuclear Information System (INIS)

Strini, Alberto; Sanson, Alessandra; Mercadelli, Elisa; Sangiorgi, Alex; Schiavi, Luca

2013-01-01

Screen-printed titania photocatalytic layers made from Degussa P25 were studied in order to assess the potential of this deposition technology for the production of catalytic surfaces for airborne pollutant degradation. The deposited catalytic TiO 2 layers were characterized by a low density (about 25% of the titania bulk crystal) typical of very porous films. The study was carried out using toluene at low concentration (12 ppb) as model pollutant and with a low UV-A irradiance level on the sample surface (200 μW cm −2 ). The catalyst layers were deposited on alumina and quartz substrates demonstrating a good catalytic depollution activity. The relationship between the layer thickness and the catalytic activity was studied in the 1 to 6.8 μm range indicating an optimal 3–4 μm film thickness. Thicker layers do not show significant increases in the catalytic activity. The optical transmittance was studied using quartz substrate samples, showing a severely reduced photon flux for layers deeper than 5 μm. The effect of post-printing thermal treatment was studied in the 500–900 °C range, demonstrating good catalytic activity for processing temperatures ≤ 700 °C. These results indicate that the screen-printing process can be a promising technology for the realization of high efficiency photocatalytic materials for air depollution applications at low UV-A irradiance. - Highlights: • Screen-printed TiO 2 has a good catalytic activity in toluene air depollution. • The overall density of screen-printed TiO 2 layer is ∼ 25% of the bulk crystal density. • The catalytic activity is demonstrated at low UV-A irradiance (200 µW cm –2 ). • The catalytic activity is dependent on the layer thickness until ∼ 4 µm thickness. • The catalytic layer has good activity up to 700 °C post-printing thermal treatment

Open-source FCPEM-Performance & Durability Model Consideration of Membrane Properties on Cathode Degradation

Energy Technology Data Exchange (ETDEWEB)

Knights, Shanna [Ballard Fuel Cell Systems, Bend, OR (United States); Harvey, David [Ballard Fuel Cell Systems, Bend, OR (United States)

2017-01-20

The durability of PEM fuel cells is a primary requirement for large scale commercialization of these power systems in transportation and stationary market applications which target operational lifetimes of 5,000 hours and 60,000 hours by 2020, respectively. Key degradation modes contributing to fuel cell lifetime limitations have been largely associated with the platinum-based cathode catalyst layer. Furthermore, as fuel cells are driven to low cost materials and lower catalyst loadings in order to meet the cost targets for commercialization, the catalyst durability has become even more important. While over the past few years significant progress has been made in identifying the underlying causes of fuel cell degradation and key parameters that greatly influence the degradation rates, many gaps with respect to knowledge of the driving mechanisms still exist; in particular, the acceleration of the mechanisms due to different membrane compositions remains an area not well understood. The focus of this project extension was to enhance the predictive capability of the PEM Fuel Cell Performance & Durability Model called FC-APOLLO (Application Package for Open-source Long Life Operation) by including interaction effects of membrane transport properties such as water transport, changes in proton conductivity, and overall water uptake/adsorption and the state of the catalyst layer local conditions to further understand the driving forces for platinum dissolution.

Facile and large-scale synthesis of high quality few-layered graphene nano-platelets via methane decomposition over unsupported iron family catalysts

Energy Technology Data Exchange (ETDEWEB)

Awadallah, Ahmed E., E-mail: ahmedelsayed_epri@yahoo.com [Process Development Division, Egyptian Petroleum Research Institute, 11727 Cairo (Egypt); Aboul-Enein, Ateyya A. [Process Development Division, Egyptian Petroleum Research Institute, 11727 Cairo (Egypt); Kandil, Usama F. [Petroleum Application Department, Egyptian Petroleum Research Institute, 11727 Cairo (Egypt); Taha, Mahmoud Reda [Department of Civil Engineering, University of New Mexico, Albuquerque, NM 87131 (United States)

2017-04-15

High quality few-layered graphene nano-platelets (GNPs) were successfully prepared via catalytic chemical vapor deposition of methane under ambient pressure using substrate-free unsupported iron, cobalt, and nickel metallic sheets as catalysts. The bulk catalysts were prepared via combustion method using citric acid as a fuel. Various analytical techniques, including high-resolution transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), temperature programmed reduction (TPR) and Raman spectroscopy were employed to characterize the fresh and reduced catalysts and to identify the morphological structure of the as-grown GNPs. TEM images of the reduced metal catalysts showed that polycrystalline metallic sheets were easily produced after complete reduction of unsupported metal oxides. The data demonstrated that the formation of zero-valent metallic sheets could effectively promote the growth of GNPs on their surfaces. The unsupported Ni catalyst exhibits higher catalytic growth activity in terms of GNPs yield (254 wt%) compared with all other catalysts. Raman spectra and TEM results established that a few layers of GNPs with high crystallinity and good graphitization were produced. TGA results further demonstrated that the as-grown GNPs exhibit significantly higher thermal stability in air atmosphere compared with other synthesis methods. - Highlights: • Few-layered graphene nanoplatelets were prepared via methane catalytic decomposition. • Metallic sheets of iron group metals were used as novel catalysts. • The surfaces of metallic sheets were found to be very effective for GNPs growth. • The number of layers is dependent on the morphological structure of the catalysts. • The unsupported metallic Ni catalyst exhibited higher catalytic growth activity.

Nanostructured CoP: An efficient catalyst for degradation of organic pollutants by activating peroxymonosulfate

Energy Technology Data Exchange (ETDEWEB)

Luo, Rui; Liu, Chao; Li, Jiansheng, E-mail: lijsh@mail.njust.edu.cn; Wang, Jing; Hu, Xingru; Sun, Xiuyun; Shen, Jinyou; Han, Weiqing; Wang, Lianjun

2017-05-05

Highlights: • The CoP/PMS system was first presented for decomposition of pollutants. • CoP exhibited dramatic catalytic activity. • Broadened pH range and favorable anti-interference of anions were achieved. • A possible mechanism for activation of PMS by CoP was proposed. - Abstract: A new catalyst system of CoP/peroxymonosulfate (PMS) is presented, which achieved significant improvement in catalytic activity. Nanostructured CoP, obtained by a simple solid-state reaction, exhibited dramatic catalytic activity with 97.2% degradation of orange II of 100 ppm within 4 min. Moreover, the high efficiency could be reached for other phenolic pollutants, i.e., phenol and 4-chlorophenol. The reaction rate is much higher than the most reported catalysts. Effect of parameters on catalytic activity of the catalyst was studied in detail. Notably, initial pH of the solution had a slight negative effect on the catalytic performance over the pH range 4.07–10.92, suggesting that CoP has the great adaptability of pH. CoP/PMS demonstrated excellent anti-interference performance toward anions (Cl{sup −}, NO{sub 3}{sup −}, and HCO{sub 3}{sup −}). In addition, the pathway of degradation of orange II is proposed by analyzing its intermediates. Based on the XPS spectra of CoP, the identification of the reactive species (·OH and SO{sub 4}·{sup −}) by electron paramagnetic resonance (EPR) analysis and quenching tests, a possible mechanism for activation of PMS by CoP was proposed. Considering the dramatic catalytic activity, a wide range of pH catalyst suited, CoP is believed to provide robust support for the promising industrial application of AOPs.

Alkaline earth layered benzoates as reusable heterogeneous catalysts for the methyl esterification of benzoic acid

Directory of Open Access Journals (Sweden)

Swamy Arêa Maruyama

2012-01-01

Full Text Available This paper describes the synthesis and characterization of layered barium, calcium and strontium benzoates and evaluates the potential of these materials as catalysts in the synthesis of methyl benzoate. The methyl esterification of benzoic acid was investigated, where the effects of temperature, alcohol:acid molar ratio and amount of catalyst were evaluated. Ester conversions of 65 to 70% were achieved for all the catalysts under the best reaction conditions. The possibility of recycling these metallic benzoates was also demonstrated, evidenced by unaltered catalytic activity for three consecutive reaction cycles.

MgAl-Layered Double Hydroxide Solid Base Catalysts for Henry Reaction: A Green Protocol

Directory of Open Access Journals (Sweden)

Magda H. Abdellattif

2018-03-01

Full Text Available A series of MgAl-layered double hydroxide (MgAl-HT, the calcined form at 500 °C (MgAlOx, and the rehydrated one at 25 °C (MgAl-HT-RH were synthesized. Physicochemical properties of the catalysts were characterized by X-ray diffraction (XRD and scanning electron microscopy (SEM. Surface area of the as-synthesized, calcined, and rehydrated catalysts was determined by N2 physisorption at −196 °C. CO2 temperature-programmed desorption (CO2-TPD was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1–15 were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90 °C in liquid phase or under microwave irradiation method. The mesoporous structure and basic nature of the rehydrated solid catalyst were responsible for its superior catalytic efficiency. The robust nature was determined by using the same catalyst five times, where the product % yield was almost unchanged significantly.

Unraveling micro- and nanoscale degradation processes during operation of high-temperature polymer-electrolyte-membrane fuel cells

Science.gov (United States)

Hengge, K.; Heinzl, C.; Perchthaler, M.; Varley, D.; Lochner, T.; Scheu, C.

2017-10-01

The work in hand presents an electron microscopy based in-depth study of micro- and nanoscale degradation processes that take place during the operation of high-temperature polymer-electrolyte-membrane fuel cells (HT-PEMFCs). Carbon supported Pt particles were used as cathodic catalyst material and the bimetallic, carbon supported Pt/Ru system was applied as anode. As membrane, cross-linked polybenzimidazole was used. Scanning electron microscopy analysis of cross-sections of as-prepared and long-term operated membrane-electrode-assemblies revealed insight into micrometer scale degradation processes: operation-caused catalyst redistribution and thinning of the membrane and electrodes. Transmission electron microscopy investigations were performed to unravel the nanometer scale phenomena: a band of Pt and Pt/Ru nanoparticles was detected in the membrane adjacent to the cathode catalyst layer. Quantification of the elemental composition of several individual nanoparticles and the overall band area revealed that they stem from both anode and cathode catalyst layers. The results presented do not demonstrate any catastrophic failure but rather intermediate states during fuel cell operation and indications to proceed with targeted HT-PEMFC optimization.

Effect of Nafion ionometer content on proton conductivity in the catalyst layer of proton exchange fuel cell

Energy Technology Data Exchange (ETDEWEB)

Ozalevlia, Cihan Cemil; Jian Xie; Xu, Fan [METU MS Mechanical Engineering (United States)], email: cihan.ozalevli@metu.edu.tr, email: jianxie@iupui.edu, email: fanxu@iupui.edu

2011-07-01

In the energy conversion sector, proton exchange fuel cells (PEFC's) are among the most promising technologies for the future. The Nafion ionometer is the most important part of the membrane electrode assembly (MEA) which is the core technology of the system. The Nafion ionometer is both a proton conductor and a binder for the catalyst layer in the technology. The aim of this study is to assess the effect of the Nafion content in the cathode catalyst layer on the proton conductivity of the MEA. Two MEAs with different Nafion content were prepared following the LANL process and the proton conductivity of the catalyst layer was measured. Results showed a much higher performance of the 28wt. % Nafion MEA than the 10wt. %. This study demonstrated that when the Nafion ionometer content decreases, the performance of the fuel cell decreases; further investigations should be undertaken with Nafion ionometer amounts of 15wt. % to 20wt. %.

3D Analysis of Fuel Cell Electrocatalyst Degradation on Alternate Carbon Supports.

Science.gov (United States)

Sneed, Brian T; Cullen, David A; Reeves, Kimberly S; Dyck, Ondrej E; Langlois, David A; Mukundan, Rangachary; Borup, Rodney L; More, Karren L

2017-09-06

Understanding the mechanisms associated with Pt/C electrocatalyst degradation in proton exchange membrane fuel cell (PEMFC) cathodes is critical for the future development of higher-performing materials; however, there is a lack of information regarding Pt coarsening under PEMFC operating conditions within the cathode catalyst layer. We report a direct and quantitative 3D study of Pt dispersions on carbon supports (high surface area carbon (HSAC), Vulcan XC-72, and graphitized carbon) with varied surface areas, graphitic character, and Pt loadings ranging from 5 to 40 wt %. This is accomplished both before and after catalyst-cycling accelerated stress tests (ASTs) through observations of the cathode catalyst layer of membrane electrode assemblies. Electron tomography results show Pt nanoparticle agglomeration occurs predominantly at junctions and edges of aggregated graphitized carbon particles, leading to poor Pt dispersion in the as-prepared catalysts and increased coalescence during ASTs. Tomographic reconstructions of Pt/HSAC show much better initial Pt dispersions, less agglomeration, and less coarsening during ASTs in the cathode. However, a large loss of the electrochemically active surface area (ECSA) is still observed and is attributed to accelerated Pt dissolution and nanoparticle coalescence. Furthermore, a strong correlation between Pt particle/agglomerate size and measured ECSA is established and is proposed as a more useful metric than average crystallite size in predicting degradation behavior across different catalyst systems.

Fe1-xZnxS ternary solid solution as an efficient Fenton-like catalyst for ultrafast degradation of phenol.

Science.gov (United States)

Gao, Jing; Liu, Yutang; Xia, Xinnian; Wang, Longlu; Dong, Wanyue

2018-07-05

Heterogeneous Fenton-like system has been proved to be an promising alternative to Fenton system due to its easy separation. However, it's a challenge to design heterogeneous Fenton-like catalysts with high activity and great durability. Here, ternary solid solution Fe 1-x Zn x S were prepared via hydrothermal synthesis as heterogeneous Fenton-like catalysts. The Fe 0.7 Zn 0.3 S sample exhibited state of the art activity for yielding OH by H 2 O 2 decomposition, and the ultrafast degradation of phenol was achieved in 4 min at initial acidic condition under room temperature. The phenol degradation rate constant of Fe 0.7 Zn 0.3 S was 99 and 70 times of ZnS and FeS, respectively. Further, we show that the unique structural configuration of iron atoms, the formation of FeS 2 -pyrite with (200) plane, are responsible for the excellent activity. The intermediate products were identified by LC-MS and a possible pathway was accordingly proposed to elucidate the mechanism of phenol degradation by OH. Overall, this work provides an idea for the rational design of the relevant heterogeneous Fenton-like catalysts. Copyright © 2018 Elsevier B.V. All rights reserved.

Degradação de poliolefinas utilizando catalisadores zeolíticos Degradation of polyolefins using zeolitic catalysts

Directory of Open Access Journals (Sweden)

Maria Letícia M. Valle

2004-03-01

Full Text Available Neste trabalho foi estudada a degradação de alguns dos principais constituintes dos rejeitos plásticos (polietileno de alta densidade (HDPE, polietileno de baixa densidade (LDPE e polipropileno (PP, empregando-se um catalisador exausto de unidades de craqueamento de fluidos (FCC e um catalisador zeolítico (ADZ3 sintetizado em laboratório. Utilizando técnicas de termogravimetria (TG-DTG e cromatografia gasosa (CG, foi possível avaliar os produtos gerados no craqueamento destas poliolefinas. Na degradação catalítica de poliolefinas com catalisadores zeolíticos, verificou-se a obtenção preferencial de gasolina, GLP e diesel, produtos importantes na matriz energética brasileira. O catalisador de FCC exausto foi mais seletivo para a produção de gasolina e GLP, enquanto que a produção de diesel foi mais favorecida com o catalisador ADZ3.In this work the degradation of some of the main plastics responsible for waste, viz. high density polyethylene (HDPE, low density polyethylene (LDPE and polypropylene (PP, was studied using a spent FCC catalyst (fluid cracking catalyst and a zeolitic catalyst (ADZ3 synthesized in laboratory. Using thermogravimetry (TG-DTG and gas chromatography (GC techniques, it was possible to evaluate the products from these polyolefins cracking. The catalytic degradation of polyolefins led to a preferential production of LPG, diesel and gasoline, which are important products of the Brazilian energetic matrix. The spent FCC catalyst was more selective for production of LPG and gasoline, whereas the diesel production was more favored with the ADZ3 catalyst.

Regeneration of LOHC dehydrogenation catalysts: In-situ IR spectroscopy on single crystals, model catalysts, and real catalysts from UHV to near ambient pressure

International Nuclear Information System (INIS)

Amende, Max; Kaftan, Andre; Bachmann, Philipp; Brehmer, Richard; Preuster, Patrick; Koch, Marcus

2016-01-01

Graphical abstract: - Highlights: • We examine the regeneration of Pt-based catalysts poisoned by LOHC degradation. • A microscopic mechanism of the removal of degradation products from Pt is proposed. • Results of our UHV studies on model catalysts are transferred to real catalysis. • Oxidative regeneration of Pt/alumina is possible under mild conditions (600 K). • The degree and temperature regime of regeneration depends on the catalyst morphology. - Abstract: The Liquid Organic Hydrogen Carrier (LOHC) concept offers an efficient route to store hydrogen using organic compounds that are reversibly hydrogenated and dehydrogenated. One important challenge towards application of the LOHC technology at a larger scale is to minimize degradation of Pt-based dehydrogenation catalysts during long-term operation. Herein, we investigate the regeneration of Pt/alumina catalysts poisoned by LOHC degradation. We combine ultrahigh vacuum (UHV) studies on Pt(111), investigations on well-defined Pt/Al_2O_3 model catalysts, and near-ambient pressure (NAP) measurements on real core–shell Pt/Al_2O_3 catalyst pellets. The catalysts were purposely poisoned by reaction with the LOHC perhydro-dibenzyltoluene (H18-MSH) and with dicyclohexylmethane (DCHM) as a simpler model compound. We focus on oxidative regeneration under conditions that may be applied in real dehydrogenation reactors. The degree of poisoning and regeneration under oxidative reaction conditions was quantified using CO as a probe molecule and measured by infrared reflection-absorption spectroscopy (IRAS) and diffuse reflectance Fourier transform IR spectroscopy (DRIFTS) for planar model systems and real catalysts, respectively. We find that regeneration strongly depends on the composition of the catalyst surface. While the clean surface of a poisoned Pt(111) single crystal is fully restored upon thermal treatment in oxygen up to 700 K, contaminated Pt/Al_2O_3 model catalyst and core–shell pellet were only

Regeneration of LOHC dehydrogenation catalysts: In-situ IR spectroscopy on single crystals, model catalysts, and real catalysts from UHV to near ambient pressure

Energy Technology Data Exchange (ETDEWEB)

Amende, Max, E-mail: max.amende@fau.de [Lehrstuhl für Physikalische Chemie II, Friedrich-Alexander-Universität Erlangen-Nürnberg, Egerlandstr. 3, 91058 Erlangen (Germany); Kaftan, Andre, E-mail: andre.kaftan@fau.de [Lehrstuhl für Physikalische Chemie II, Friedrich-Alexander-Universität Erlangen-Nürnberg, Egerlandstr. 3, 91058 Erlangen (Germany); Bachmann, Philipp, E-mail: philipp.bachmann@fau.de [Lehrstuhl für Physikalische Chemie II, Friedrich-Alexander-Universität Erlangen-Nürnberg, Egerlandstr. 3, 91058 Erlangen (Germany); Brehmer, Richard, E-mail: richard.brehmer@fau.de [Lehrstuhl für Chemische Reaktionstechnik, Friedrich-Alexander-Universität Erlangen-Nürnberg, Egerlandstr. 3, 91058 Erlangen (Germany); Preuster, Patrick, E-mail: patrick.preuster@fau.de [Lehrstuhl für Chemische Reaktionstechnik, Friedrich-Alexander-Universität Erlangen-Nürnberg, Egerlandstr. 3, 91058 Erlangen (Germany); Koch, Marcus, E-mail: marcus.koch@crt.cbi.uni-erlangen.de [Lehrstuhl für Chemische Reaktionstechnik, Friedrich-Alexander-Universität Erlangen-Nürnberg, Egerlandstr. 3, 91058 Erlangen (Germany); and others

2016-01-01

Graphical abstract: - Highlights: • We examine the regeneration of Pt-based catalysts poisoned by LOHC degradation. • A microscopic mechanism of the removal of degradation products from Pt is proposed. • Results of our UHV studies on model catalysts are transferred to real catalysis. • Oxidative regeneration of Pt/alumina is possible under mild conditions (600 K). • The degree and temperature regime of regeneration depends on the catalyst morphology. - Abstract: The Liquid Organic Hydrogen Carrier (LOHC) concept offers an efficient route to store hydrogen using organic compounds that are reversibly hydrogenated and dehydrogenated. One important challenge towards application of the LOHC technology at a larger scale is to minimize degradation of Pt-based dehydrogenation catalysts during long-term operation. Herein, we investigate the regeneration of Pt/alumina catalysts poisoned by LOHC degradation. We combine ultrahigh vacuum (UHV) studies on Pt(111), investigations on well-defined Pt/Al{sub 2}O{sub 3} model catalysts, and near-ambient pressure (NAP) measurements on real core–shell Pt/Al{sub 2}O{sub 3} catalyst pellets. The catalysts were purposely poisoned by reaction with the LOHC perhydro-dibenzyltoluene (H18-MSH) and with dicyclohexylmethane (DCHM) as a simpler model compound. We focus on oxidative regeneration under conditions that may be applied in real dehydrogenation reactors. The degree of poisoning and regeneration under oxidative reaction conditions was quantified using CO as a probe molecule and measured by infrared reflection-absorption spectroscopy (IRAS) and diffuse reflectance Fourier transform IR spectroscopy (DRIFTS) for planar model systems and real catalysts, respectively. We find that regeneration strongly depends on the composition of the catalyst surface. While the clean surface of a poisoned Pt(111) single crystal is fully restored upon thermal treatment in oxygen up to 700 K, contaminated Pt/Al{sub 2}O{sub 3} model catalyst and

The platinum catalyst layer in polymer-electrolyte fuel cells[Dissertation 17127]; Die Platinkatalysatorschicht in Polymerelektrolyt-Brennstoffzellen. Beitraege zum Verstaendnis und zur Optimierung

Energy Technology Data Exchange (ETDEWEB)

Reiner, A.

2007-07-01

This illustrated, comprehensive dissertation by Dr. Andreas Reiner presents an in-depth analysis of polymer electrolyte fuel cells (PEFC) and in particular, their platinum catalyst layer. First of all, the thermodynamics and kinetics involved are reviewed, along with components, their efficiencies and the catalyst layer. The methods used, including scanning electron microscope, x-ray and Rutherford spectroscopy are discussed. The structure and composition of co-sputtered catalyst layers and their production are described. Electro-chemical activation and the electro-chemical properties of the layers are discussed. The second part of the dissertation deals with the principle of hydrogen under-potential deposition. This method provides information about the electrochemically active platinum surface fraction. The results of investigations made are presented and discussed.

Isotope exchange in oxide-containing catalyst

Science.gov (United States)

Brown, Kenneth G. (Inventor); Upchurch, Billy T. (Inventor); Hess, Robert V. (Inventor); Miller, Irvin M. (Inventor); Schryer, David R. (Inventor); Sidney, Barry D. (Inventor); Wood, George M. (Inventor); Hoyt, Ronald F. (Inventor)

1989-01-01

A method of exchanging rare-isotope oxygen for common-isotope oxygen in the top several layers of an oxide-containing catalyst is disclosed. A sample of an oxide-containing catalyst is exposed to a flowing stream of reducing gas in an inert carrier gas at a temperature suitable for the removal of the reactive common-isotope oxygen atoms from the surface layer or layers of the catalyst without damaging the catalyst structure. The reduction temperature must be higher than any at which the catalyst will subsequently operate. Sufficient reducing gas is used to allow removal of all the reactive common-isotope oxygen atoms in the top several layers of the catalyst. The catalyst is then reoxidized with the desired rare-isotope oxygen in sufficient quantity to replace all of the common-isotope oxygen that was removed.

Synthesis and characterization of Acacia gum-Fe0Np-silica nanocomposite: an efficient Fenton-like catalyst for the degradation of Remazol Brilliant Violet dye

Science.gov (United States)

Singh, Vandana; Singh, Jadveer; Srivastava, Preeti

2018-04-01

Acacia gum-Fe0Np-silica nanocomposite (GFS1) has been crafted through sol-gel technique using a two-step process that involved the reduction of iron salt to zerovalent iron nanoparticles (Fe0Nps) followed by their impregnation within Acacia gum-silica matrix. GFS1 was characterized using Fourier transform infrared spectroscopy (FTIR), high-resolution transmission electron microscopy (HR-TEM), energy dispersive X-ray analysis (EDX), field emission scanning electron microscopy (FE-SEM), vibrating sample magnetometry (VSM), and X-ray photoelectron spectroscopy (XPS) techniques. GFS1 is decorated with Fe0Nps of 5 nm average size. The VSM study revealed that GFS1 has ferromagnetic nature. GFS1 was used as a heterogeneous Fenton-like catalyst for the degradation of azo dyes using Remazol Brilliant Violet (RBV) dye as a model dye. In first 5 min of operation, > 86% dye degradation was achieved and 94% dye (from 100 mg L-1 dye solution) was successfully degraded in 50 min. The dye degradation followed pseudo-first-order kinetics. The GFS1 performed efficiently well over the wide range of dye concentrations (25-200 mg L-1). The catalyst was reused for eight repeated cycles where 12.5% dye degradation was possible even in the eighth cycle. The catalyst behaved fairly well for the degradation of Metanil Yellow (MY) and Orange G (OG) dyes also. Under the optimum conditions of RBV dye degradation, Metanil Yellow (MY) and Orange G (OG) dyes were degraded to the extent of 97 and 26.3%, respectively.

Single-Step Electrophoretic Deposition of Non-noble Metal Catalyst Layer with Low Onset Voltage for Ethanol Electro-oxidation.

Science.gov (United States)

Ahmadi Daryakenari, Ahmad; Hosseini, Davood; Ho, Ya-Lun; Saito, Takumi; Apostoluk, Aleksandra; Müller, Christoph R; Delaunay, Jean-Jacques

2016-06-29

A single-step electrophoretic deposition (EPD) process is used to fabricate catalyst layers which consist of nickel oxide nanoparticles attached on the surface of nanographitic flakes. Magnesium ions present in the colloid charge positively the flake's surface as they attach on it and are also used to bind nanographitic flakes together. The fabricated catalyst layers showed a very low onset voltage (-0.2 V vs Ag/AgCl) in the electro-oxidation of ethanol. To clarify the occurring catalytic mechanism, we performed annealing treatment to produce samples having a different electrochemical behavior with a large onset voltage. Temperature dependence measurements of the layer conductivity pointed toward a charge transport mechanism based on hopping for the nonannealed layers, while the drift transport is observed in the annealed layers. The hopping charge transport is responsible for the appearance of the low onset voltage in ethanol electro-oxidation.

Electrically conductive aluminum oxide thin film used as cobalt catalyst-support layer in vertically aligned carbon nanotube growth

International Nuclear Information System (INIS)

Azam, Mohd Asyadi; Ismail, Syahriza; Mohamad, Noraiham; Isomura, Kazuki; Shimoda, Tatsuya

2015-01-01

This paper will present the unique characteristics of aluminum oxide (Al–O) and cobalt catalyst included in aligned carbon nanotube (CNT) electrode system of energy storage device, namely electrochemical capacitor. Electrical conductivity and nanostructure of the thermally oxidized Al–O used as catalyst-support layer in vertically grown single-walled CNTs were studied. Al–O films were characterized by means of current–voltage measurement and high resolution transmission electron microscopy analysis. The Al–O support layer was found to be conductive, with a relatively low resistance and, approximately 20 nm film thickness of Al–O is suggested to be too thin to form insulating barrier. The scanning TEM—annular dark field analysis confirmed that the nanosized cobalt catalyst particles distributed on Al–O surfaces and also embedded inside the Al–O film structure. (paper)

Modified Fe3O4- hydroxyapatite nanocomposites as heterogeneous catalysts in three UV, Vis and Fenton like degradation systems

International Nuclear Information System (INIS)

Valizadeh, S.; Rasoulifard, M.H.; Dorraji, M.S. Seyed

2014-01-01

Graphical abstract: - Highlights: • Photocatalytic degradation of dye by Ag modified HAP under visible light. • Study of Fenton like degradation of dye by transition metal ions modified HAP. • Comparison of catalytic systems according to Langmuir-Hinshelwood kinetic expression. - Abstract: The magnetite-hydroxyapatite (M-HAP) nanocomposites were prepared by a chemical co- precipitation procedure and characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and diffuse reflectance spectra (DRS). The ability of the synthesized catalyst for photocatalytic degradation of Acid Blue 25 (AB25), as an organic dye, under UV irradiation was studied. The catalyst was modified employing transition metals (Mn, Fe, Co, Ni, Cu and Zn) trying to improve the catalytic performance of HAP in absence of UV irradiation and in the presence of hydrogen peroxide i.e. a Fenton like reaction. The best results obtained for Cu and Co modified M-HAPs and the effect of operational parameters such pH, amount of catalyst and hydrogen peroxide concentration was studied. In order to investigate the performance of HAP based photocatalyst in visible light region, M-HAP was modified with silver ions. At the end, Langmuir-Hinshelwood kinetic expression used to evaluate and compare the catalytic systems. The strongest degradation activity was observed for Ag-M-HAP/Vis system because of Ag 3 PO 4 formation. Apparent reaction rate constant (K app ) by Ag-M-HAP/Vis was 63, 36 and 19 times faster than Cu-M-HAP(II)/H 2 O 2 , Co-M-HAP(II)/H 2 O 2 and M-HAP (I)/UV systems, respectively

Catalyst containing oxygen transport membrane

Science.gov (United States)

Christie, Gervase Maxwell; Wilson, Jamie Robyn; van Hassel, Bart Antonie

2012-12-04

A composite oxygen transport membrane having a dense layer, a porous support layer and an intermediate porous layer located between the dense layer and the porous support layer. Both the dense layer and the intermediate porous layer are formed from an ionic conductive material to conduct oxygen ions and an electrically conductive material to conduct electrons. The porous support layer has a high permeability, high porosity, and a high average pore diameter and the intermediate porous layer has a lower permeability and lower pore diameter than the porous support layer. Catalyst particles selected to promote oxidation of a combustible substance are located in the intermediate porous layer and in the porous support adjacent to the intermediate porous layer. The catalyst particles can be formed by wicking a solution of catalyst precursors through the porous support toward the intermediate porous layer.

Graphene layer encapsulated metal nanoparticles as a new type of non-precious metal catalysts for oxygen reduction

DEFF Research Database (Denmark)

Hu, Yang; Zhong, Lijie; Jensen, Jens Oluf

2016-01-01

Cheap and efficient non-precious metal catalysts for oxygen reduction have been a focus of research in the field of low-temperature fuel cells. This review is devoted to a brief summary of the recent work on a new type of catalysts, i.e., the graphene layer encapsulated metal nanoparticles....... The discussion is focused on the synthesis, structure, mechanism, performance, and further research....

HETEROGENEOUS PHOTOCATALYTIC DEGRADATION OF PHENOL IN AQUEOUS SUSPENSION OF PERIWINKLE SHELL ASH CATALYST IN THE PRESENCE OF UV FROM SUNLIGHT

Directory of Open Access Journals (Sweden)

OSARUMWENSE, J. O.

2015-12-01

Full Text Available The batch photocatalytic degradation of phenol in aqueous solution wasinvestigated using periwinkle shell ash (PSA as photocatalyst. Chemical characterisation of the PSA revealed that the major oxides present were calcium oxide (CaO, silica (SiO2 and aluminium oxide (Al2O3 which accounted for 41.3, 33.2 and 9.2% of the weight of PSA characterised. The major elements in PSA were iron (19.2% and zinc (16.5%. FTIR results revealed absorption peaks of 3626.59 cm−1, 1797.58 cm−1, 1561.43 cm−1 and 1374.34 cm−1 in the infrared spectrum of PSA corresponding to O–H, C= O, C= C and C–H bonds respectively. Increasing the initial phenol concentration resulted in a decrease in the degradation efficiency of PSA. Lower catalyst loadings favoured the degradation process. Maximum degradation efficiency was obtained when the initial phenol concentration and catalyst loading were set as 50 g/L and 5 g/L respectively. The kinetics of the degradation process was well described by the pseudo first order equation while the diffusion mechanism was well represented by the intra particle diffusion model (R2>0.90. The adsorption equilibrium data fitted well to the Langmuir isotherm equation with an R2 value of 0.997.

The synthesis of hierarchical nanostructured MoS_2/Graphene composites with enhanced visible-light photo-degradation property

International Nuclear Information System (INIS)

Zhao, Yongjie; Zhang, Xiaowei; Wang, Chengzhi; Zhao, Yuzhen; Zhou, Heping; Li, Jingbo; Jin, HaiBo

2017-01-01

Graphical abstract: Introducing graphene layer into MoS_2 could construct the steady hierarchical structure which could efficiently separate the photo-induced electrons so as to enhance the photo- degradation behavior. - Highlights: • The MoS_2 and MoS_2/Graphene nanocomposite have been synthesized via a solvothermal process. • The scrolled nanosheets of MoS_2 combining with interconnected graphene network promoted the formation of steady hierarchical architecture. • Comparing with MoS_2, the hierarchical MoS_2/Graphene nanocomposite achieved relatively higher degradation rate. • The synergistic effect mechanism for excellent photo-degradation activity was proposed. - Abstract: Novel two-dimensional materials with a layered structure are of special interest for a variety of promising applications. Herein, MoS_2 and MoS_2/Graphene nanocomposite with hierarchical nanostructure were successfully synthesized employing a one-step hydrothermal method. Photo-degradation of methylene blue (MB) and rhodamine (RHB) were adopted to assess the photo-degradation ability of the products. Comparing with bare MoS_2, the hierarchical MoS_2/Graphene nanocomposite achieved relatively higher degradation rate of 99% in 28 min for MB as well in 50 min for RHB. These results verified that this proposed hierarchical nanocomposite is a good photo-degradation semiconductor. The excellent performance was mainly ascribed to the synergistic effect of MoS_2 and graphene layers. The MoS_2 possessing a band gap of 1.9 eV would provide abundant electron-hole pairs. The graphene layers with excellent electro-conductivity could realize the quick transport of electrons via its extended π-conjugation structure, consequently benefiting the separation of photo-generated carriers. These findings indicate that the graphene layer is a promising candidate as a co-catalyst for MoS_2 photo-catalyst, and also provide useful information for understanding the observed enhanced photocatalytic mechanism

Degradation of l-polylactide during melt processing with layered double hydroxides

DEFF Research Database (Denmark)

Gerds, Nathalie; Katiyar, Vimal; Koch, Christian Bender

2012-01-01

PLA was melt compounded in small-scale batches with two forms of laurate-modified magnesium–aluminum layered double hydroxide (Mg-Al-LDH-C12), the corresponding carbonate form (Mg-Al-LDH-CO3) and a series of other additives. Various methods were then adopted to characterize the resulting compounds...... in an effort to gain greater insights into PLA degradation during melt processing. PLA molecular weight reduction was found to vary according to the type of LDH additive. It is considered that the degree of particle dispersion and LDH exfoliation, and hence the accessibility of the hydroxide layer surfaces...... and catalytically active Mg site centers are causative factors for PLA degradation. Interestingly, the release of water under the processing conditions was found to have a rather small effect on the PLA degradation. Low loadings of sodium laurate also caused PLA degradation indicating that carboxylate chain ends...

A comparative parametric study of a catalytic plate methane reformer coated with segmented and continuous layers of combustion catalyst for hydrogen production

Science.gov (United States)

Mundhwa, Mayur; Parmar, Rajesh D.; Thurgood, Christopher P.

2017-03-01

A parametric comparison study is carried out between segmented and conventional continuous layer configurations of the coated combustion-catalyst to investigate their influence on the performance of methane steam reforming (MSR) for hydrogen production in a catalytic plate reactor (CPR). MSR is simulated on one side of a thin plate over a continuous layer of nickel-alumina catalyst by implementing an experimentally validated surface microkinetic model. Required thermal energy for the MSR reaction is supplied by simulating catalytic methane combustion (CMC) on the opposite side of the plate over segmented and continuous layer of a platinum-alumina catalyst by implementing power law rate model. The simulation results of both coating configurations of the combustion-catalyst are compared using the following parameters: (1) co-flow and counter-flow modes between CMC and MSR, (2) gas hourly space velocity and (3) reforming-catalyst thickness. The study explains why CPR designed with the segmented combustion-catalyst and co-flow mode shows superior performance not only in terms of high hydrogen production but also in terms of minimizing the maximum reactor plate temperature and thermal hot-spots. The study shows that the segmented coating requires 7% to 8% less combustion-side feed flow and 70% less combustion-catalyst to produce the required flow of hydrogen (29.80 mol/h) on the reforming-side to feed a 1 kW fuel-cell compared to the conventional continuous coating of the combustion-catalyst.

N-doped TiO2 photo-catalyst for the degradation of 1,2-dichloroethane under fluorescent light

International Nuclear Information System (INIS)

Lin, Yi-Hsing; Chiu, Tang-Chun; Hsueh, Hsin-Ta; Chu, Hsin

2011-01-01

The photo-catalytic degradation of 1,2-dichloroethane (1, 2-DCE) using nitrogen-doped TiO 2 photo-catalysts under fluorescent light irradiation was investigated. Highly pure TiO 2 and nitrogen-doped TiO 2 were prepared by a sol-gel method and characterized by thermo-gravimetric/differential-thermal analysis (TG/DTA), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared (FTIR) spectroscopy. The results indicate that the photo-catalysts were mainly nano-size with an anatase-phase structure. The degradation reaction of 1,2-DCE was operated under visible-light irradiation, and the photo-catalytic oxidation was conducted in a batch photo-reactor with various nitrogen doping ratios (N/Ti = 0-25 mol%). The relative humidity (RH) was controlled at 0-20% and the oxygen concentration was controlled at 0-21%. The photo-degradation with nitrogen-doped TiO 2 showed superior photo-catalytic activity compared to that for pure TiO 2 . TiO 2 doped with 15 mol% nitrogen exhibited the best photo-catalytic efficiency under the tested conditions. The products from the 1,2-DCE photo-catalytic oxidation were CO 2 and water; the by-products included dichloromethane, methyl chloride, ethyl chloride, carbon monoxide, and hydrogen chloride. The reaction pathway of 1,2-DCE indicates that oxygen molecules are the major factor that causes the degradation of 1,2-DCE in the gas phase.

DOE Award No. DE-FC36-03GO13108 NOVEL NON-PRECIOUS METAL CATALYSTS FOR PEMFC: CATALYST SELECTION THROUGH MOLECULAR MODELING AND DURABILITY STUDIES Final Report (September 2003 – October 2008)

Energy Technology Data Exchange (ETDEWEB)

Branko N. Popov

2009-02-20

The objective of this project is to develop novel non-precious metal electrocatalysts for oxygen reduction reaction (ORR), and demonstrate the potential of the catalysts to perform at least as good as conventional Pt catalysts currently in use in polymer electrolyte membrane fuel cell (PEMFC) with a cost at least 50 % less than a target of 0.2 g (Pt loading)/peak kW and with durability > 2,000 h operation with less than 10 % power degradation. A novel nitrogen-modified carbon-based catalyst was obtained by modifying carbon black with nitrogen-containing organic precursor in the absence of transition metal precursor. The catalyst shows the onset potential of approximately 0.76 V (NHE) for ORR and the amount of H2O2 of approximately 3% at 0.5 V (NHE). Furthermore, a carbon composite catalyst was achieved through the high-temperature pyrolysis of the precursors of transition metal (Co and Fe) and nitrogen supported on the nitrogen-modified carbon-based catalyst, followed by chemical post-treatment. This catalyst showed an onset potential for ORR as high as 0.87 V (NHE), and generated less than 1 % of H2O2. The PEM fuel cell exhibited a current density of 2.3 A cm-2 at 0.2 V for a catalyst loading of 6.0 mg cm-2. No significant performance degradation was observed for 480 h continuous operation. The characterization studies indicated that the metal-nitrogen chelate complexes decompose at the temperatures above 800 oC. During the pyrolysis, the transition metals facilitate the incorporation of pyridinic and graphitic nitrogen groups into the carbon matrix, and the carbon surface modified with nitrogen is active for ORR. In order to elucidate the role of transition metal precursor played in the formation of active sites in the non-precious metal catalysts, a novel ruthenium-based chelate (RuNx) catalyst was synthesized by using RuCl3 and propylene diammine as the Ru and N precursors, respectively, followed by high-temperature pyrolysis. This catalyst exhibited comparable

DOE Award No. DE-FC36-03GO13108 NOVEL NON-PRECIOUS METAL CATALYSTS FOR PEMFC: CATALYST SELECTION THROUGH MOLECULAR MODELING AND DURABILITY STUDIES Final Report (September 2003 – October 2008)

Energy Technology Data Exchange (ETDEWEB)

Branko N. Popov

2009-03-03

The objective of this project is to develop novel non-precious metal electrocatalysts for oxygen reduction reaction (ORR), and demonstrate the potential of the catalysts to perform at least as good as conventional Pt catalysts currently in use in polymer electrolyte membrane fuel cell (PEMFC) with a cost at least 50 % less than a target of 0.2 g (Pt loading)/peak kW and with durability > 2,000 h operation with less than 10 % power degradation. A novel nitrogen-modified carbon-based catalyst was obtained by modifying carbon black with nitrogen-containing organic precursor in the absence of transition metal precursor. The catalyst shows the onset potential of approximately 0.76 V (NHE) for ORR and the amount of H2O2 of approximately 3% at 0.5 V (NHE). Furthermore, a carbon composite catalyst was achieved through the high-temperature pyrolysis of the precursors of transition metal (Co and Fe) and nitrogen supported on the nitrogen-modified carbon-based catalyst, followed by chemical post-treatment. This catalyst showed an onset potential for ORR as high as 0.87 V (NHE), and generated less than 1 % of H2O2. The PEM fuel cell exhibited a current density of 2.3 A cm-2 at 0.2 V for a catalyst loading of 6.0 mg cm-2. No significant performance degradation was observed for 480 h continuous operation. The characterization studies indicated that the metal-nitrogen chelate complexes decompose at the temperatures above 800 oC. During the pyrolysis, the transition metals facilitate the incorporation of pyridinic and graphitic nitrogen groups into the carbon matrix, and the carbon surface modified with nitrogen is active for ORR. In order to elucidate the role of transition metal precursor played in the formation of active sites in the non-precious metal catalysts, a novel ruthenium-based chelate (RuNx) catalyst was synthesized by using RuCl3 and propylene diammine as the Ru and N precursors, respectively, followed by high-temperature pyrolysis. This catalyst exhibited comparable

Multi-Directional Growth of Aligned Carbon Nanotubes Over Catalyst Film Prepared by Atomic Layer Deposition

Directory of Open Access Journals (Sweden)

Zhou Kai

2010-01-01

Full Text Available Abstract The structure of vertically aligned carbon nanotubes (CNTs severely depends on the properties of pre-prepared catalyst films. Aiming for the preparation of precisely controlled catalyst film, atomic layer deposition (ALD was employed to deposit uniform Fe2O3 film for the growth of CNT arrays on planar substrate surfaces as well as the curved ones. Iron acetylacetonate and ozone were introduced into the reactor alternately as precursors to realize the formation of catalyst films. By varying the deposition cycles, uniform and smooth Fe2O3 catalyst films with different thicknesses were obtained on Si/SiO2 substrate, which supported the growth of highly oriented few-walled CNT arrays. Utilizing the advantage of ALD process in coating non-planar surfaces, uniform catalyst films can also be successfully deposited onto quartz fibers. Aligned few-walled CNTs can be grafted on the quartz fibers, and they self-organized into a leaf-shaped structure due to the curved surface morphology. The growth of aligned CNTs on non-planar surfaces holds promise in constructing hierarchical CNT architectures in future.

Layered double hydroxide catalyst for the conversion of crude vegetable oils to a sustainable biofuel

Science.gov (United States)

Mollaeian, Keyvan

Over the last two decades, the U.S. has developed the production of biodiesel, a mixture of fatty acid methyl esters, using chiefly vegetable oils as feedstocks. However, there is much concern about the availability of high-quality vegetable oils for longterm biodiesel production. Problems have also risen due to the production of glycerol, an unwanted byproduct, as well as the need for process wash water. Therefore, this study was initiated to produce not only fatty acid methyl esters (FAMEs) but also fatty acid glycerol carbonates (FAGCs) by replacing methanol with dimethyl carbonate (DMC). The process would have no unnecessary byproducts and would be a simplified process compared to traditional biodiesel. In addition, this altering of the methylating agent could convert triglycerides, free fatty acids, and phospholipids to a sustainable biofuel. In this project, Mg-Al Layered Double Hydroxide (LDH) was optimized by calcination in different temperature varied from 250°C to 450°C. The gallery between layers was increased by intercalating sodium dodecylsulfate (SDS). During catalyst preparation, the pH was controlled ~10. In our experiment, triazabicyclodecene (TBD) was attached with trimethoxysilane (3GPS) as a coupling agent, and N-cetyl-N,N,N-trimethylammonium bromide (CTAB) was added to remove SDS from the catalyst. The catalyst was characterized by XRD, FTIR, and Raman spectroscopy. The effect of the heterogeneous catalyst on the conversion of canola oil, corn oil, and free fatty acids was investigated. To analyze the conversion of lipid oils to biofuel an in situ Raman spectroscopic method was developed. Catalyst synthesis methods and a proposed mechanism for converting triglycerides and free fatty acids to biofuel will be presented.

Electrocatalytic activity of atomic layer deposited Pt-Ru catalysts onto N-doped carbon nanotubes

NARCIS (Netherlands)

Johansson, A.-C.; Larsen, J.V.; Verheijen, M.A.; Haugshøj, K.B.; Clausen, H.; Kessels, W.M.M.; Christensen, L.H.; Thomsen, E.V.

2014-01-01

Pt-Ru catalysts of various compositions, between 0 and 100 at.% of Ru, were deposited onto N-doped multi-walled carbon nanotubes (N-CNTs) by atomic layer deposition (ALD) at 250 C. The Pt and Ru precursors were trimethyl(methylcyclopentadienyl)platinum (MeCpPtMe3) and

One-step prepared cobalt-based nanosheet as an efficient heterogeneous catalyst for activating peroxymonosulfate to degrade caffeine in water.

Science.gov (United States)

Lin, Kun-Yi Andrew; Lai, Hong-Kai; Tong, Shaoping

2018-03-15

Two-dimensional (2D) planar cobalt-containing materials are promising catalysts for activating peroxymonosulfate (PMS) to degrade contaminants because 2D sheet-like morphology provides large reactive surfaces. However, preparation of these sheet-supported cobaltic materials typically involves multiple steps and complex reagents, making them less practical for PMS activation. In this study, a cobalt-based nanosheet (CoNS) is particularly developed using a one-step hydrothermal process with a single reagent in water. The resulting CoNS can exhibit a thickness as thin as a few nanometers and 2-D morphology. CoNS is also primarily comprised of cobalt species in a coordinated form of Prussian Blue analogue, which consists of both Co 3+ and Co 2+ . These features make CoNS promising for activating PMS in aqueous systems. As degradation of an emerging contaminant, caffeine, is selected as a representative reaction, CoNS not only successfully activates PMS to fully degrade caffeine in 20 min but also exhibits a much higher catalytic activity than the most common PMS activator, Co 3 O 4 . Via studying inhibitive effects of radical scavengers, caffeine degradation by CoNS-activated PMS is primarily attributed to sulfate radicals and hydroxyl radicals to a lesser extent. The degradation products of caffeine by CoNS-activated PMS are also identified and a potential degradation pathway is proposed. Moreover, CoNS could be also re-used to activate PMS for caffeine degradation without activity loss. These results indicate that CoNS is a conveniently prepared and highly effective and stable 2-D catalyst for aqueous chemical oxidation reactions. Copyright © 2017. Published by Elsevier Inc.

Catalyst support structure, catalyst including the structure, reactor including a catalyst, and methods of forming same

Science.gov (United States)

Van Norman, Staci A.; Aston, Victoria J.; Weimer, Alan W.

2017-05-09

Structures, catalysts, and reactors suitable for use for a variety of applications, including gas-to-liquid and coal-to-liquid processes and methods of forming the structures, catalysts, and reactors are disclosed. The catalyst material can be deposited onto an inner wall of a microtubular reactor and/or onto porous tungsten support structures using atomic layer deposition techniques.

Graphitic carbon nitride induced activity enhancement of OMS-2 catalyst for pollutants degradation with peroxymonosulfate

Science.gov (United States)

Li, Jun; Fang, Jia; Gao, Long; Zhang, Jingwen; Ruan, Xinchao; Xu, Aihua; Li, Xiaoxia

2017-04-01

Low valent manganese species and surface oxygen vacancies in OMS-2 play an important role in catalytic reactions, and it is highly desirable and challenging to develop a feasible strategy of increasing the Mn(II) and Mn(III) species concentration in the oxide. Herein, the OMS-2/g-C3N4 hybrids (OMS-2/CN) were prepared by a facile refluxing approach. It was found that the MnOx precursor from the reaction of KMnO4 and MnSO4 was transformed into OMS-2 nanofibers with the formation of more Mn(II) and Mn(III) species in OMS-2 and the destruction and oxidation of g-C3N4. The hybrids exhibited higher efficiency for pollutants degradation in the presence of PMS than the pure OMS-2 or g-C3N4. There was a linear correlation between the specific initial rate and the ratio of Mn(II + III)/Mn(IV). Mechanism investigation indicated that high active manganese species or caged radicals were produced through the oxidation of Mn(II) and Mn(III) by PMS and contributed to the degradation reaction. During five consecutive cycles, the catalyst exhibited good reusability and stability. Therefore, the OMS-2/CN hybrids are promising catalysts for wastewater treatment with PMS as the oxidant.

Photocatalytic degradation of TCE in water using TiO{sub 2} catalyst

Energy Technology Data Exchange (ETDEWEB)

Farooq, Muhammad [Pakistan National Accreditation Council, 4th Floor Evacuee Trust Complex, F-5/1 Islamabad (Pakistan); Raja, Iftikhar A.; Pervez, Arshad [Department of Environmental Sciences, COMSATS Institute of Information Technology, Abbottabad (Pakistan)

2009-09-15

Wastewater is generally released untreated into the rivers and streams in developing countries. Industrial wastewater usually contains highly toxic pollutants, cyanides, chlorinated compounds such as trichloroethylene (TCE). Ultraviolet (UV) radiation from sunlight also decomposes organic compounds by oxidation process. However, the process is less effective due to large amount of toxic effluent entering the main stream water. The solar radiation can effectively be applied to accelerate the process by using suitable catalyst for economically cleaning the major fresh water sources. This paper describes photocatalytic degradation of trichloroethylene in aqueous solution using TiO{sub 2}. Variable parameters such as initial concentration of TCE, type and concentration of TiO{sub 2} and reaction time are investigated. The powder TiO{sub 2} is found more effective than the sand TiO{sub 2} for decomposing TCE. The effect of sand TiO{sub 2} as photocatalyst is investigated at various water depths. It is observed that up to 45 mm water depth, sand TiO{sub 2} shows photo-degradation of TCE. The degradation rate increases as the concentration of TCE is increased up to 45 {mu}l of TCE per litre of water. Similarly the photocatalytic degradation increases with TiO{sub 2} concentration up to 0.7 g L{sup -1} of solution but then starts decreasing. The optimum values of TiO{sub 2} and TCE concentration obtained are 0.7 g and 35 {mu}l L{sup -1} of the solution, respectively. (author)

Plasmonic Ag-pillared rectorite as catalyst for degradation of 2,4-DCP in the H{sub 2}O{sub 2}-containing system under visible light irradiation

Energy Technology Data Exchange (ETDEWEB)

Chen, Yunfang [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Fang, Jianzhang, E-mail: fangjzh@scnu.edu.cn [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Guangdong Technology Research Center for Ecological Management and Remediation of Urban Water System, Guangzhou 510006 (China); Lu, Shaoyou [Shenzhen Center for Disease Control and Prevention, Shenzhen 518055 (China); Wu, Yan; Chen, Dazhi; Huang, Liyan [Institute of Engineering Technology of Guangdong Province, Key Laboratory of Water Environmental Pollution Control of Guangdong Province, Guangzhou 510440 (China); Cheng, Cong; Ren, Lu; Zhu, Ximiao [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Fang, Zhanqiang [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Guangdong Technology Research Center for Ecological Management and Remediation of Urban Water System, Guangzhou 510006 (China)

2015-10-30

Highlights: • The Ag-R catalyst was synthesized via a novel thermal decomposition method. • Ag-R catalyst possessed the synergistic effects of SPR and adsorption capacity. • The degradation of 2,4-DCP was evaluated in Ag-R/H{sub 2}O{sub 2}/visible light system. - Abstract: This study aims at photocatalytic degradation of 2,4-DCP with the assistance of H{sub 2}O{sub 2} in aqueous solution by a composite catalyst of Ag-rectorite. The catalysts were prepared via a novel thermal decomposition method followed after the cation-exchange process. The synthesized nano-materials were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET) surface analyzer, Ultraviolet–visible light (UV–vis) absorption spectra, field-emission scanning electron microscope (FE-SEM) and transmission electron microscope (TEM). The different mechanisms of degradation process with or without visible light irradiation were discussed, respectively. Moreover, the degradation efficiency of 2,4-DCP wastewater under Ag-rectorite/H{sub 2}O{sub 2}/visible light system was investigated by series of experiments, concerning on effects of major operation factors, such as H{sub 2}O{sub 2} dosage and the initial pH value. The highest degradation rate was observed when adding 0.18 mL H{sub 2}O{sub 2} into 50 mL 2,4-DCP solution, and the optimal pH value was 4 for the reaction. Afterwards, total organic carbon (TOC) experiments were carried out to evaluate the mineralization ratio of 2,4-DCP.

Mechanical behaviour of PEM fuel cell catalyst layers during regular cell operation

OpenAIRE

Maher A.R. Sadiq Al-Baghdadi

2010-01-01

Damage mechanisms in a proton exchange membrane fuel cell are accelerated by mechanical stresses arising during fuel cell assembly (bolt assembling), and the stresses arise during fuel cell running, because it consists of the materials with different thermal expansion and swelling coefficients. Therefore, in order to acquire a complete understanding of the mechanical behaviour of the catalyst layers during regular cell operation, mechanical response under steady-state hygro-thermal stresses s...

High-efficiency and conveniently recyclable photo-catalysts for dye degradation based on urchin-like CuO microparticle/polymer hybrid composites

Science.gov (United States)

Liu, Xiong; Cheng, Yuming; Li, Xuefeng; Dong, Jinfeng

2018-05-01

In this work, we developed a new type of photo-catalysts composed of the urchin-like cupric oxide (CuO) microparticle and polyvinylidene fluoride (PVDF) hybrid composites by the convenient organic-inorganic hybrid strategy, which show high-efficiency and conveniently recyclable for dye degradation including methylene blue (MB), Congo red (CR), and malachite green (MG) by visible light irradiation. The micro-structural characteristics of urchin-like CuO microparticles are crucial and dominant over the photo-degrading efficiency of hybrid catalyst because of their highly exposed {0 0 2} facet and larger specific surface area. Simultaneously, the intrinsic porous framework of PVDF membrane not only remains the excellent photo-catalytic activity of urchin-like CuO microparticles but also facilitates the enrichment of dyes on the membrane, and thereby synergistically contributing to the photo-catalytic efficiency. The microstructures of both urchin-like CuO microparticles and hybrid catalysts are systematically characterized by various techniques including scanning electron microscopy (SEM), transmission electron microscope (TEM), high-resolution transmission electron microscope (HRTEM), powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), and nitrogen adsorption/desorption isotherms, which evidently support the mentioned mechanism.

The fabrication of a carbon nanotube array using a catalyst-poisoning layer in the inverse nano-sphere lithography method

International Nuclear Information System (INIS)

Tsai, Tsung-Yen; Chen, Tsung-Han; Tai, Nyan-Hwa; Chang, Shih-Chin; Hsu, Hui-Chen; Joseph Palathinkal, Thomas

2009-01-01

A new method for the fabrication of periodic CNT arrays was developed in this study, which involves the use of the inverse nano-sphere lithography (INSL) process. Mo of a honeycomb pattern, acting as a catalyst-poisoning layer, was produced by the nano-sphere lithography (NSL) process; the Mo poisoned the catalyst and prevented CNT growth where deposited, and as a result, a periodic CNT pattern was obtained. Using this method, the uniformity of the CNT array can be improved by preventing the negative effect of arrangement defects in self-assembled monolayers. The size and the period of the CNT array can be adjusted by careful selection of the polystyrene (PS) sphere diameter. X-ray photoelectron spectroscope (XPS) analysis revealed that the Co catalyst was ineffective on the areas of Mo deposition due to the diffusion of Co into the Mo layer.

The fabrication of a carbon nanotube array using a catalyst-poisoning layer in the inverse nano-sphere lithography method

Energy Technology Data Exchange (ETDEWEB)

Tsai, Tsung-Yen; Chen, Tsung-Han; Tai, Nyan-Hwa; Chang, Shih-Chin; Hsu, Hui-Chen; Joseph Palathinkal, Thomas, E-mail: nhtai@mx.nthu.edu.t [Department of Materials Science and Engineering, National Tsing Hua University, 101, Section 2, Kuang-Fu Road, Hsinchu, 30013, Taiwan (China)

2009-07-29

A new method for the fabrication of periodic CNT arrays was developed in this study, which involves the use of the inverse nano-sphere lithography (INSL) process. Mo of a honeycomb pattern, acting as a catalyst-poisoning layer, was produced by the nano-sphere lithography (NSL) process; the Mo poisoned the catalyst and prevented CNT growth where deposited, and as a result, a periodic CNT pattern was obtained. Using this method, the uniformity of the CNT array can be improved by preventing the negative effect of arrangement defects in self-assembled monolayers. The size and the period of the CNT array can be adjusted by careful selection of the polystyrene (PS) sphere diameter. X-ray photoelectron spectroscope (XPS) analysis revealed that the Co catalyst was ineffective on the areas of Mo deposition due to the diffusion of Co into the Mo layer.

Temperature aspect of degradation of electrochemical double-layer capacitors (EDLC)

Science.gov (United States)

Baek, Dong-Cheon; Kim, Hyun-Ho; Lee, Soon-Bok

2015-03-01

Electric double layer capacitors (EDLC) cells have a process variation and temperature dependency in capacitance so that balancing is required when they are connected in series, which includes electronic voltage management based on capacitance monitoring. This paper measured temperature aspect of capacitance periodically to monitor health and degradation behavior of EDLC stressed under high temperatures and zero below temperatures respectively, which enables estimation of the state of health (SOH) regardless of temperature. At high temperature, capacitance saturation and delayed expression of degradation was observed. After cyclic stress at zero below temperature, less effective degradation and time recovery phenomenon were occurred.

Open circuit voltage durability study and model of catalyst coated membranes at different humidification levels

Energy Technology Data Exchange (ETDEWEB)

Kundu, Sumit; Fowler, Michael W.; Simon, Leonardo C. [Department of Chemical Engineering, University of Waterloo, 200 University Avenue West, Waterloo, Ontario (Canada); Abouatallah, Rami; Beydokhti, Natasha [Hydrogenics Corporation, 5985 McLaughlin Road, Mississauga, Ontario (Canada)

2010-11-01

Fuel cell material durability is an area of extensive research today. Chemical degradation of the ionomer membrane is one important degradation mechanism leading to overall failure of fuel cells. This study examined the effects of relative humidity on the chemical degradation of the membrane during open circuit voltage testing. Five Gore trademark PRIMEA {sup registered} series 5510 catalyst coated membranes were degraded at 100%, 75%, 50%, and 20% RH. Open circuit potential and cumulative fluoride release were monitored over time. Additionally scanning electron microscopy images were taken at end of the test. The results showed that with decreasing RH fluoride release rate increased as did performance degradation. This was attributed to an increase in gas crossover with a decrease in RH. Further, it is also shown that interruptions in testing may heavily influence cumulative fluoride release measurements where frequent stoppages in testing will cause fluoride release to be underestimated. SEM analysis shows that degradation occurred in the ionomer layer close to the cathode catalyst. A chemical degradation model of the ionomer membrane was used to model the results. The model was able to predict fluoride release trends, including the effects of interruptions, showing that changes in gas crossover with RH could explain the experimental results. (author)

Increasing the lifetime of fuel cell catalysts

NARCIS (Netherlands)

Latsuzbaia, R.

2015-01-01

In this thesis, I discuss a novel idea of fuel cell catalyst regeneration to increase lifetime of the PEM fuel cell electrode/catalyst operation and, therefore, reduce the catalyst costs. As many of the catalyst degradation mechanisms are difficult to avoid, the regeneration is alternative option to

Gradient Mn-La-Pt Catalysts with Three-layered Structure for Li-O2 battery

Science.gov (United States)

Cai, Kedi; Yang, Rui; Lang, Xiaoshi; Zhang, Qingguo; Wang, Zhenhua; He, Tieshi

2016-01-01

Gradient Mn-La-Pt catalysts with three-layered structure of manganese dioxide (MnO2), lanthanum oxide (La2O3), and Platinum (Pt) for Li-O2 battery are prepared in this study. The mass ratio of the catalysts is respectively 5:2:3, 4:2:4, and 3:2:5 (MnO2: La2O3: Pt) which is start from the side of the electrolyte. The relationship between morphology structure and electrochemical performance of gradient catalyst is investigated by energy dispersive spectrometry and constant current charge/discharge test. The Li-O2 battery based on gradient Mn-La-Pt catalysts shows high discharge specific capacity (2707 mAh g−1), specific energy density (8400 Wh kg−1) and long cycle life (56 cycles). The improvement of the Li-O2 battery discharge capacity is attributed to the gradient distribution of MnO2 and Pt and the involvement of La2O3 that can improve the energy density of the battery. More important, this work will also provide new ideas and methods for the research of other metal-air battery. PMID:27731340

Marine sponge skeleton photosensitized by copper phthalocyanine: A catalyst for Rhodamine B degradation

Directory of Open Access Journals (Sweden)

Norman Małgorzata

2016-01-01

Full Text Available We present a combined approach to photo-assisted degradation processes, in which a catalyst, H2O2 and UV irradiation are used together to enhance the oxidation of Rhodamine B (RB. The heterogeneous photocatalyst was made by the process of adsorption of copper phthalocyanine tetrasulfonic acid (CuPC onto purified spongin-based Hippospongia communis marine sponge skeleton (HcS. The product obtained, CuPC-HcS, was investigated by a variety of spectroscopic (carbon-13 nuclear magnetic resonance 13C NMR, Fourier transform infrared spectroscopy FTIR, energy-dispersive X-ray spectroscopy EDS and microscopic techniques (scanning electron microscopy SEM, fluorescent and optical microscopy, as well as thermal analysis. The study confirms the stable combination of the adsorbent and adsorbate. For a 10 mg/L RB solution, the percentage degradation reached 95% using CuPC-HcS as a heterocatalyst. The mechanism of RB removal involves adsorption and photodegradation simultaneously.

Electrostatic self-assembly of Fe3O4/GO nanocomposites and their application as an efficient Fenton-like catalyst for degradation of rhodamine B

Science.gov (United States)

Wang, Wenxia; He, Qi; Xiao, Kaijun; Zhu, Liang

2018-03-01

In the study, a two-major step involving a hydrothermal method and an electrostatic self-assembly method was adopted to synthesis Fe3O4/GO nanocomposites. The Fe3O4 nanoparticles were successfully modified with the 3-aminopropyltrimethoxy-silane and homogeneously deposited onto the surface of GO. They were used as Fenton-like catalyst to degrade Rhodamine B and displayed a higher activity compared with the pristine Fe3O4 nanoparticles, H2O2, Fe3O4/GO nanocomposite and Fe3O4/H2O2 system, demonstrating the synergistic effect between the superior adsorption properties of GO and the excellent catalytic activity of Fe3O4/H2O2 system. Besides, the possible catalytic mechanism and degradation pathway for RhB molecules by Fe3O4/GO nanocomposites and H2O2 was proposed based on the liquid chromatography-mass spectrometry (LC-MS) analysis. The result reveals that the •OH radicals should be the main actives species during catalytic degradation of RhB by the Fe3O4/GO/H2O2 system. In addition, the catalyst is reusable and shows efficiency up to 5 cycles. We believe the strategy in our work can provide insight into designing the novel catalysts for large-scale degradation of organic pollutants in the wastewater.

Modified Fe{sub 3}O{sub 4}- hydroxyapatite nanocomposites as heterogeneous catalysts in three UV, Vis and Fenton like degradation systems

Energy Technology Data Exchange (ETDEWEB)

Valizadeh, S., E-mail: valizadehsolmaz@yahoo.com; Rasoulifard, M.H., E-mail: m_h_rasoulifard@znu.ac.ir; Dorraji, M.S. Seyed, E-mail: dorraji@znu.ac.ir

2014-11-15

Graphical abstract: - Highlights: • Photocatalytic degradation of dye by Ag modified HAP under visible light. • Study of Fenton like degradation of dye by transition metal ions modified HAP. • Comparison of catalytic systems according to Langmuir-Hinshelwood kinetic expression. - Abstract: The magnetite-hydroxyapatite (M-HAP) nanocomposites were prepared by a chemical co- precipitation procedure and characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and diffuse reflectance spectra (DRS). The ability of the synthesized catalyst for photocatalytic degradation of Acid Blue 25 (AB25), as an organic dye, under UV irradiation was studied. The catalyst was modified employing transition metals (Mn, Fe, Co, Ni, Cu and Zn) trying to improve the catalytic performance of HAP in absence of UV irradiation and in the presence of hydrogen peroxide i.e. a Fenton like reaction. The best results obtained for Cu and Co modified M-HAPs and the effect of operational parameters such pH, amount of catalyst and hydrogen peroxide concentration was studied. In order to investigate the performance of HAP based photocatalyst in visible light region, M-HAP was modified with silver ions. At the end, Langmuir-Hinshelwood kinetic expression used to evaluate and compare the catalytic systems. The strongest degradation activity was observed for Ag-M-HAP/Vis system because of Ag{sub 3}PO{sub 4} formation. Apparent reaction rate constant (K{sub app}) by Ag-M-HAP/Vis was 63, 36 and 19 times faster than Cu-M-HAP(II)/H{sub 2}O{sub 2}, Co-M-HAP(II)/H{sub 2}O{sub 2} and M-HAP (I)/UV systems, respectively.

The Potential of Fe-exchanged Y Zeolite as a Heterogeneous Fenton-type Catalyst for Oxidative Degradation of Reactive Dye in Water

OpenAIRE

Aleksić, M.; Koprivanac, N.; Lončarić Božić, A.; Kušić, H.

2010-01-01

The study aimed to investigate the potential of Fe-exchanged zeolites of Y-type as a catalyst in heterogeneous Fenton-type processes for the degradation of model organic pollutant, reactive azo dye C.I. Reactive Blue 137, in water. The research work was directed to investigate the influence of process variables, such as FeY catalyst dosage, Fenton reagent ratio, and initial operating pH on the efficiency of the treatment process. The performance of the studied heterogeneous process was compar...

CuAu–ZnO–graphene nanocomposite: A novel graphene-based bimetallic alloy-semiconductor catalyst with its enhanced photocatalytic degradation performance

International Nuclear Information System (INIS)

Xie, Hong; Ye, Xiaoliang; Duan, Kaiyue; Xue, Muyin; Du, Yongling; Ye, Weichun; Wang, Chunming

2015-01-01

Graphical abstract: In this work, we have successfully synthesized a novel graphene-based bimetallic alloy-semiconductor catalyst: CuAu–ZnO–Gr nanocomposite, and which behaved an enhanced photocatalytic activity. - Highlights: • A bimetallic alloy-based catalyst: CuAu–ZnO–Gr is synthesized. • CuAu–ZnO–Gr behaves an enhanced photocatalytic activity. • The detailed explanation of photocatalytic mechanism of CuAu–ZnO–Gr. - Abstract: The bimetallic alloy CuAu nanoparticles (NPs) can produce more photogenerated electrons when compared with single metal Au NPs. Moreover, graphene (Gr) sheets can help the charge separation and slow down the recombination of the electron hole pairs of ZnO. Hence, a novel graphene-based bimetallic alloy-semiconductor catalyst: CuAu–ZnO–Gr nanocomposite is synthesized. Due to the synergistic effect among CuAu NPs, ZnO nanopyramids, and Gr sheets, CuAu–ZnO–Gr behaves an enhanced photocatalytic activity for the photocatalytic degradation of synthetic colorants methyl orange (MO), methylene blue (MB), indigotin (IN), sunset yellow (SY), and tartrazine (TT) under the simulated sunlight irradiation. Furthermore, the apparent rate constants (k app ) of MO, MB, IN, SY, and TT degradation are estimated respectively. In addition, the as-prepared CuAu–ZnO–Gr nanocomposite is characterized by X-ray diffraction, UV–vis spectrum, transmission electron microscopy, energy dispersive X-ray analysis (EDX), and EDX mapping. As a result of the facile synthesis route and the enhanced photocatalytic activity, this new material CuAu–ZnO–Gr can be a promising photocatalyst for the degradation of dyes

CuAu–ZnO–graphene nanocomposite: A novel graphene-based bimetallic alloy-semiconductor catalyst with its enhanced photocatalytic degradation performance

Energy Technology Data Exchange (ETDEWEB)

Xie, Hong [College of Chemistry and Chemical Engineering, Lanzhou University, Lanzhou 730000 (China); Ye, Xiaoliang [College of Chemistry and Chemical Engineering, Lanzhou University, Lanzhou 730000 (China); College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China); Duan, Kaiyue; Xue, Muyin; Du, Yongling; Ye, Weichun [College of Chemistry and Chemical Engineering, Lanzhou University, Lanzhou 730000 (China); Wang, Chunming, E-mail: wangcm@lzu.edu.cn [College of Chemistry and Chemical Engineering, Lanzhou University, Lanzhou 730000 (China)

2015-07-05

Graphical abstract: In this work, we have successfully synthesized a novel graphene-based bimetallic alloy-semiconductor catalyst: CuAu–ZnO–Gr nanocomposite, and which behaved an enhanced photocatalytic activity. - Highlights: • A bimetallic alloy-based catalyst: CuAu–ZnO–Gr is synthesized. • CuAu–ZnO–Gr behaves an enhanced photocatalytic activity. • The detailed explanation of photocatalytic mechanism of CuAu–ZnO–Gr. - Abstract: The bimetallic alloy CuAu nanoparticles (NPs) can produce more photogenerated electrons when compared with single metal Au NPs. Moreover, graphene (Gr) sheets can help the charge separation and slow down the recombination of the electron hole pairs of ZnO. Hence, a novel graphene-based bimetallic alloy-semiconductor catalyst: CuAu–ZnO–Gr nanocomposite is synthesized. Due to the synergistic effect among CuAu NPs, ZnO nanopyramids, and Gr sheets, CuAu–ZnO–Gr behaves an enhanced photocatalytic activity for the photocatalytic degradation of synthetic colorants methyl orange (MO), methylene blue (MB), indigotin (IN), sunset yellow (SY), and tartrazine (TT) under the simulated sunlight irradiation. Furthermore, the apparent rate constants (k{sub app}) of MO, MB, IN, SY, and TT degradation are estimated respectively. In addition, the as-prepared CuAu–ZnO–Gr nanocomposite is characterized by X-ray diffraction, UV–vis spectrum, transmission electron microscopy, energy dispersive X-ray analysis (EDX), and EDX mapping. As a result of the facile synthesis route and the enhanced photocatalytic activity, this new material CuAu–ZnO–Gr can be a promising photocatalyst for the degradation of dyes.

Modified Fe3O4- hydroxyapatite nanocomposites as heterogeneous catalysts in three UV, Vis and Fenton like degradation systems

Science.gov (United States)

Valizadeh, S.; Rasoulifard, M. H.; Dorraji, M. S. Seyed

2014-11-01

The magnetite-hydroxyapatite (M-HAP) nanocomposites were prepared by a chemical co- precipitation procedure and characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and diffuse reflectance spectra (DRS). The ability of the synthesized catalyst for photocatalytic degradation of Acid Blue 25 (AB25), as an organic dye, under UV irradiation was studied. The catalyst was modified employing transition metals (Mn, Fe, Co, Ni, Cu and Zn) trying to improve the catalytic performance of HAP in absence of UV irradiation and in the presence of hydrogen peroxide i.e. a Fenton like reaction. The best results obtained for Cu and Co modified M-HAPs and the effect of operational parameters such pH, amount of catalyst and hydrogen peroxide concentration was studied. In order to investigate the performance of HAP based photocatalyst in visible light region, M-HAP was modified with silver ions. At the end, Langmuir-Hinshelwood kinetic expression used to evaluate and compare the catalytic systems. The strongest degradation activity was observed for Ag-M-HAP/Vis system because of Ag3PO4 formation. Apparent reaction rate constant (Kapp) by Ag-M-HAP/Vis was 63, 36 and 19 times faster than Cu-M-HAP(II)/H2O2, Co-M-HAP(II)/H2O2 and M-HAP (I)/UV systems, respectively.

Catalytic Combustion of Low Concentration Methane over Catalysts Prepared from Co/Mg-Mn Layered Double Hydroxides

Directory of Open Access Journals (Sweden)

Hongfeng Liu

2014-01-01

Full Text Available A series of Co/Mg-Mn mixed oxides were synthesized through thermal decomposition of layered double hydroxides (LDHs precursors. The resulted catalysts were then subjected for catalytic combustion of methane. Experimental results revealed that the Co4.5Mg1.5Mn2LDO catalyst possessed the best performance with the T90=485°C. After being analyzed via XRD, BET-BJH, SEM, H2-TPR, and XPS techniques, it was observed that the addition of cobalt had significantly improved the redox ability of the catalysts whilst certain amount of magnesium was essential to guarantee the catalytic activity. The presence of Mg was helpful to enhance the oxygen mobility and, meanwhile, improved the dispersion of Co and Mn oxides, preventing the surface area loss after calcination.

Atomic Layer Deposited Catalysts for Fuel Cell Applications

DEFF Research Database (Denmark)

Johansson, Anne-Charlotte Elisabeth Birgitta

catalyst toward the methanol oxidation reaction (MOR). In the work described in this PhD dissertation, two series of Pt-Ru ALD catalysts supported on nitrogen-doped multi-walled carbon nanotubes (N-CNTs) have been evaluated toward the CO oxidation and MOR at room temperature in a three......The micro direct methanol fuel cell (µDMFC) has been proposed as a candidate to power portable applications. The device can operate at room temperature on inexpensive, energy-dense methanol fuel, and it can be easily "recharged" by fuel refilling. Microfabrication techniques could be one route......-electrode electrochemical cell. The first series was comprised of Pt-Ru ALD catalysts of various Ru compositions, between 0 and 100 at.%. For the compositions investigated, the best catalyst had a Ru composition of 29 at.%. In the second series Ru-decorated Pt catalysts of various Ru loadings, i.e., various Ru ALD cycles...

Photoassisted Fenton degradation of phthalocyanine dyes from wastewater of printing industry using Fe(II)/γ-Al2O3 catalyst in up-flow fluidized-bed.

Science.gov (United States)

Cheng, Hsuhui; Chou, Shihjie; Chen, Shiaoshing; Yu, Chiajen

2014-06-01

Fe(II)/γ-Al2O3 powders synthesized using the dipping method were produced from a mixed aqueous solution containing aluminium oxide (γ-Al2O3) and iron(II)-precursor (FeSO4), and used for photo-Fenton degradation of phthalocyanine dyes (PCS) under ultraviolet (UV) irradiation in an up-flow fluidized bed. The catalysts were characterized by XRD, ESCA, BET, EDS and SEM. The results showed that Fe(2+) ion was compounded on the γ-Al2O3 carrier. The effects of different reaction parameters such as catalyst activity, dosage and solution pH on the decolorization of PCS were assessed. Results indicated that maximum decolorization (more than 95%) of PCS occurred with 20 wt% Fe(II)/γ-Al2O3 catalyst (dosage of 60 g/L) using a combination of UV irradiation and heterogeneous Fenton system. The degradation efficiency of PCS increases as pH decreases, exhibiting a maximum efficiency at pH 3.5. The recycled catalyst was capable of repeating three runs without a significant decrease in treatment efficiency, and this demonstrated the stability and reusability of catalyst. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

The Enhanced Catalytic Performance and Stability of Rh/γ-Al₂O₃ Catalyst Synthesized by Atomic Layer Deposition (ALD) for Methane Dry Reforming.

Science.gov (United States)

Li, Yunlin; Jiang, Jing; Zhu, Chaosheng; Li, Lili; Li, Quanliang; Ding, Yongjie; Yang, Weijie

2018-01-22

Rh/γ-Al₂O₃ catalysts were synthesized by both incipient wetness impregnation (IWI) and atomic layer deposition (ALD). The TEM images of the two catalysts showed that the catalyst from ALD had smaller particle size, and narrower size distribution. The surface chemical states of both catalysts were investigated by both XPS and X-ray Absorption Near Edge Structure (XANES), and the catalyst from IWI had higher concentration of Rh 3+ than that from ALD. The catalytic performance of both catalysts was tested in the dry reforming of methane reaction. The catalyst from ALD showed a higher conversion and selectivity than that from IWI. The stability testing results indicated that the catalyst from ALD showed similar stability to that from IWI at 500 °C, but higher stability at 800 °C.

The synthesis of hierarchical nanostructured MoS{sub 2}/Graphene composites with enhanced visible-light photo-degradation property

Energy Technology Data Exchange (ETDEWEB)

Zhao, Yongjie, E-mail: zhaoyjpeace@gmail.com [Beijing Key Laboratory of Construction Tailorable Advanced Functional Materials and Green Applications, School of Materials Science & Engineering, Beijing Institute of Technology, Beijing, 100081 (China); Zhang, Xiaowei; Wang, Chengzhi [Beijing Key Laboratory of Construction Tailorable Advanced Functional Materials and Green Applications, School of Materials Science & Engineering, Beijing Institute of Technology, Beijing, 100081 (China); Zhao, Yuzhen; Zhou, Heping [State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Tsinghua University, Beijing, 100084 (China); Li, Jingbo; Jin, HaiBo [Beijing Key Laboratory of Construction Tailorable Advanced Functional Materials and Green Applications, School of Materials Science & Engineering, Beijing Institute of Technology, Beijing, 100081 (China)

2017-08-01

Graphical abstract: Introducing graphene layer into MoS{sub 2} could construct the steady hierarchical structure which could efficiently separate the photo-induced electrons so as to enhance the photo- degradation behavior. - Highlights: • The MoS{sub 2} and MoS{sub 2}/Graphene nanocomposite have been synthesized via a solvothermal process. • The scrolled nanosheets of MoS{sub 2} combining with interconnected graphene network promoted the formation of steady hierarchical architecture. • Comparing with MoS{sub 2}, the hierarchical MoS{sub 2}/Graphene nanocomposite achieved relatively higher degradation rate. • The synergistic effect mechanism for excellent photo-degradation activity was proposed. - Abstract: Novel two-dimensional materials with a layered structure are of special interest for a variety of promising applications. Herein, MoS{sub 2} and MoS{sub 2}/Graphene nanocomposite with hierarchical nanostructure were successfully synthesized employing a one-step hydrothermal method. Photo-degradation of methylene blue (MB) and rhodamine (RHB) were adopted to assess the photo-degradation ability of the products. Comparing with bare MoS{sub 2}, the hierarchical MoS{sub 2}/Graphene nanocomposite achieved relatively higher degradation rate of 99% in 28 min for MB as well in 50 min for RHB. These results verified that this proposed hierarchical nanocomposite is a good photo-degradation semiconductor. The excellent performance was mainly ascribed to the synergistic effect of MoS{sub 2} and graphene layers. The MoS{sub 2} possessing a band gap of 1.9 eV would provide abundant electron-hole pairs. The graphene layers with excellent electro-conductivity could realize the quick transport of electrons via its extended π-conjugation structure, consequently benefiting the separation of photo-generated carriers. These findings indicate that the graphene layer is a promising candidate as a co-catalyst for MoS{sub 2} photo-catalyst, and also provide useful information

Hydroxide catalysts for lignin depolymerization

Science.gov (United States)

Beckham, Gregg T; Biddy, Mary J.; Kruger, Jacob S.; Chmely, Stephen C.; Sturgeon, Matthew

2017-10-17

Solid base catalysts and their use for the base-catalyzed depolymerization (BCD) of lignin to compounds such as aromatics are presented herein. Exemplary catalysts include layered double hydroxides (LDHs) as recyclable, heterogeneous catalysts for BCD of lignin.

Hydroxide catalysts for lignin depolymerization

Energy Technology Data Exchange (ETDEWEB)

Beckham, Gregg T.; Biddy, Mary J.; Chmely, Stephen C.; Sturgeon, Matthew

2017-04-25

Solid base catalysts and their use for the base-catalyzed depolymerization (BCD) of lignin to compounds such as aromatics are presented herein. Exemplary catalysts include layered double hydroxides (LDHs) as recyclable, heterogeneous catalysts for BCD of lignin.

Phenol Removal by a Novel Non-Photo-Dependent Semiconductor Catalyst in a Pilot-Scaled Study: Effects of Initial Phenol Concentration, Light, and Catalyst Loading

Directory of Open Access Journals (Sweden)

Xiao Chen

2014-01-01

Full Text Available A novel non-photo-dependent semiconductor catalyst (CT was employed to degrade phenol in the present pilot-scaled study. Effect of operational parameters such as phenol initial concentration, light area, and catalyst loading on phenol degradation, was compared between CT catalyst and the conventional photocatalyst titanium dioxide. CT catalyst excelled titanium dioxide in treating and mineralizing low-level phenol, under both mild UV radiation and thunder conditions of nonphoton. The result suggested that CT catalyst could be applied in circumstances when light is not easily accessible in pollutant-carrying media (e.g., particles, cloudy water, and colored water.

Encaging palladium(0 in layered double hydroxide: A sustainable catalyst for solvent-free and ligand-free Heck reaction in a ball mill

Directory of Open Access Journals (Sweden)

Wei Shi

2017-08-01

Full Text Available In this paper, the synthesis of a cheap, reusable and ligand-free Pd catalyst supported on MgAl layered double hydroxides (Pd/MgAl-LDHs by co-precipitation and reduction methods is described. The catalyst was used in Heck reactions under high-speed ball milling (HSBM conditions at room temperature. The effects of milling-ball size, milling-ball filling degree, reaction time, rotation speed and grinding auxiliary category, which would influence the yields of mechanochemical Heck reactions, were investigated in detail. The characterization results of XRD, ICP–MS and XPS suggest that Pd/MgAl-LDHs have excellent textural properties with zero-valence Pd on its layers. The reaction results indicate that the catalyst could be utilized in HSBM systems to afford a wide range of Heck coupling products in satisfactory yields. Furthermore, this catalyst could be easily recovered and reused for at least five times without significant loss of catalytic activity.

Studies on the hydroprocessing of deashed oil. 9. ; Characterization of the used catalyst in the pilot plant. Deashed oil no suisoka bunkai hanno ni kansuru kenkyu. 9. ; Pilot plant shiyozumi shokubai no characterization

Energy Technology Data Exchange (ETDEWEB)

Kaneko, T.; Hijiriyama, M. (Mitsubishi Kasei Co., Tokyo (Japan)); Kageyama, Y. (Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan))

1990-11-29

The secondary hydroprocessing process in the two-stage hydrogenating liquefaction equipment under development at Nippon Brown Coal Liquefaction Company uses a fixed bed system. To elucidate causes of catalyst activity degradation related therewith, catalyst used for about 1000 hours in a S -t/d pilot plant was collected to investigate deposition behavior of cokes and ashed metals and changes in catalyst properties. The catalyst is made of Ca-Ni-Mo/Al2O3, which was recovered from baskets placed in each layer in a reactor, washed in a predetermined manner, dried, and analyzed. In addition, in order to investigate remaining activity, 1-methylnaphthalene was hydrogenated, and deashed oil (DAO) was hydrocracked. The result may be summarized as follows: The major cause for the catalyst activity degradation is deposition of carbonaceous materials and ashed metals on the catalyst; and especially alkali metals (Na and K) were considered to be the major cause for the catalyst deactivation with time. 2 refs., 8 figs.

Fuel starvation. Irreversible degradation mechanisms in PEM fuel cells

Energy Technology Data Exchange (ETDEWEB)

Rangel, Carmen M.; Silva, R.A.; Travassos, M.A.; Paiva, T.I.; Fernandes, V.R. [LNEG, National Laboratory for Energy and Geology, Lisboa (Portugal). UPCH Fuel Cells and Hydrogen Unit

2010-07-01

PEM fuel cell operates under very aggressive conditions in both anode and cathode. Failure modes and mechanism in PEM fuel cells include those related to thermal, chemical or mechanical issues that may constrain stability, power and lifetime. In this work, the case of fuel starvation is examined. The anode potential may rise to levels compatible with the oxidization of water. If water is not available, oxidation of the carbon support will accelerate catalyst sintering. Diagnostics methods used for in-situ and ex-situ analysis of PEM fuel cells are selected in order to better categorize irreversible changes of the cell. Electrochemical Impedance Spectroscopy (EIS) is found instrumental in the identification of fuel cell flooding conditions and membrane dehydration associated to mass transport limitations / reactant starvation and protonic conductivity decrease, respectively. Furthermore, it indicates that water electrolysis might happen at the anode. Cross sections of the membrane catalyst and gas diffusion layers examined by scanning electron microscopy indicate electrode thickness reduction as a result of reactions taking place during hydrogen starvation. Catalyst particles are found to migrate outwards and located on carbon backings. Membrane degradation in fuel cell environment is analyzed in terms of the mechanism for fluoride release which is considered an early predictor of membrane degradation. (orig.)

ZIF-67-derived hollow nanocages with layered double oxides shell as high-Efficiency catalysts for CO oxidation

Science.gov (United States)

Kong, Wenpeng; Li, Jing; Chen, Yao; Ren, Yuqing; Guo, Yonghua; Niu, Shengli; Yang, Yanzhao

2018-04-01

Constructing non-precious hybrid metal oxides with specific morphology as cost-effective and highly efficient catalysts is a promising way for the automotive exhaust purification. In this work, we report a facile strategy for the fabrication of a unique hollow Co-Ni layered double oxides (HLDO) nanocages by using zeolitic imidazole frameworks (ZIFs) as template. The synthesis of intermediate core-shell and hollow Co-Ni layered double hydroxides (HLDH) nanoflakes as well as the corresponding Co-Ni oxides products were successfully controlled, and the formation process was also explained. Among ZIF-67-derived oxides, HLDO exhibits excellent catalytic activities (complete conversion of CO into CO2 at 118 °C) and long-term stability for CO oxidation. The remarkable catalytic activities of HLDO can be attributed to high surface area (258 m2 g-1) inherited from the HLDH, which could provide more active sites for CO oxidation. In addition, active oxygen species indicated by the O 1 s XPS spectrum and improved synergistic effect between NiO and Co3O4 reflected by H2-TPR, further explain the enhanced performance of the HLDO catalysts. The presented strategy for controlled design and synthesis of hollow multicomponent metal oxides will provide prospects in developing highly effective catalysts.

Sulfate radical degradation of acetaminophen by novel iron-copper bimetallic oxidation catalyzed by persulfate: Mechanism and degradation pathways

Science.gov (United States)

Zhang, Yuanchun; Zhang, Qian; Hong, Junming

2017-11-01

A novel iron coupled copper oxidate (Fe2O3@Cu2O) catalyst was synthesized to activate persulfate (PS) for acetaminophen (APAP) degradation. The catalysts were characterized via field-emission scanning electron microscopy and energy-dispersive X-ray spectrometry. The effects of the catalyst, PS concentration, catalyst dosage, initial pH, dissolved oxygen were analyzed for treatment optimization. Results indicated that Fe2O3@Cu2O achieved higher efficiency in APAP degradation than Fe2O3/PS and Cu2O/PS systems. The optimal removal efficiency of APAP (90%) was achieved within 40 min with 0.6 g/L PS and 0.3 g/L catalyst. To clarify the mechanism for APAP degradation, intermediates were analyzed with gas chromatography-mass spectrometry. Three possible degradation pathways were identified. During reaction, Cu(I) was found to react with Fe(III) to generate Fe(II), which is the most active phase for PS activation. Through the use of methanol and tert-butyl alcohol (TBA) as radical trappers, SO4rad - was identified as the main radical species that is generated during oxidation.

Re-examination of the Pt Particle Size Effect on the Oxygen Reduction Reaction for Ultrathin Uniform Pt/C Catalyst Layers without Influence from Nafion

International Nuclear Information System (INIS)

Shinozaki, Kazuma; Morimoto, Yu; Pivovar, Bryan S.; Kocha, Shyam S.

2016-01-01

Highlights: • Pt particle size effect on ORR was re-evaluated for Pt/C catalysts. • Nafion-free activity of Pt/C catalysts was evaluated using thin-film RDE methods. • Ultrathin-uniform catalyst layers were employed to obtain accurate activity values. • Specific activity increased steeply from 2 to 10 nm and less steeply at over 10 nm. • Re-evaluated effect agrees with a particle model assuming terrace active sites. - Abstract: The platinum ‘particle size effect’ on the oxygen reduction reaction (ORR) has been re-evaluated using commercial Pt/C catalysts (2–10 nm Pt particle) and polycrystalline Pt (poly-Pt) in 0.1 M HClO 4 with a rotating disk electrode method. Nafion-free catalyst layers were employed to obtain specific activities (SA) that were not perturbed (suppressed) by sulfonate anion adsorption/blocking. By using ultrathin uniform catalyst layers, O 2 diffusion limitation was minimized as confirmed from the high SAs of our supported catalysts that were comparable to unsupported sputtered Pt having controlled sizes. The specific activity (SA) steeply increased for the particle sizes in the range ∼2–10 nm (0.8–1.8 mA/cm 2 Pt at 0.9 V vs. RHE) and plateaued over ∼10 nm to 2.7 mA/cm 2 Pt for bulk poly-Pt. On the basis of the activity trend for the range of particle sizes studied, it appears that the effect of carbon support on activity is negligible. The experimental results and the concomitant profile of SA vs. particle size was found to be in an agreement to a truncated octahedral particle model that assumes active terrace sites.

Tethered catalysts for the hydration of carbon dioxide

Science.gov (United States)

Valdez, Carlos A; Satcher, Jr., Joe H; Aines, Roger D; Wong, Sergio E; Baker, Sarah E; Lightstone, Felice C; Stolaroff, Joshuah K

2014-11-04

A system is provided that substantially increases the efficiency of CO.sub.2 capture and removal by positioning a catalyst within an optimal distance from the air-liquid interface. The catalyst is positioned within the layer determined to be the highest concentration of carbon dioxide. A hydrophobic tether is attached to the catalyst and the hydrophobic tether modulates the position of the catalyst within the liquid layer containing the highest concentration of carbon dioxide.

Apparatus and Process for Controlled Nanomanufacturing Using Catalyst Retaining Structures

Science.gov (United States)

Nguyen, Cattien (Inventor)

2013-01-01

An apparatus and method for the controlled fabrication of nanostructures using catalyst retaining structures is disclosed. The apparatus includes one or more modified force microscopes having a nanotube attached to the tip portion of the microscopes. An electric current is passed from the nanotube to a catalyst layer of a substrate, thereby causing a localized chemical reaction to occur in a resist layer adjacent the catalyst layer. The region of the resist layer where the chemical reaction occurred is etched, thereby exposing a catalyst particle or particles in the catalyst layer surrounded by a wall of unetched resist material. Subsequent chemical vapor deposition causes growth of a nanostructure to occur upward through the wall of unetched resist material having controlled characteristics of height and diameter and, for parallel systems, number density.

Synthesis, characterization and dielectric properties of polynorbornadiene–clay nanocomposites by ROMP using intercalated Ruthenium catalyst

International Nuclear Information System (INIS)

Yalçınkaya, Esra Evrim; Balcan, Mehmet; Güler, Çetin

2013-01-01

Polynorbornadiene clay nanocomposites were prepared for the first time by the ring opening metathesis polymerization (ROMP) using modified montmorillonite and polynorbornadiene the latter of which is used commonly in electric–electronic industry. The Na–MMT clay was modified by a quaternary ammonium salt containing Ruthenium complex as a suitable catalyst and intercalant as well. The norbornadiene monomers were polymerized within the modified montmorillonite layers by in-situ polymerization method in different clay loading degrees. Intercalation ability of the Ru catalyst and partially exfoliated nanocomposite structure were proved by powder X-ray Diffraction (XRD) Spectroscopy and Transmission Electron Microscopy (TEM) methods. The nanocomposite materials with high thermal degradation temperature and low dielectric constant compared to the pure polynorbornadiene were obtained. The dielectric constants decreased with the increase of the clay content. - Highlights: • Polynorbornadiene–clay nanocomposites were prepared for the first time. • Ruthenium complex was assigned as both suitable catalyst and intercalant. • The norbornadiene was polymerized by in-situ polymerization method. • Exfoliation/intercalation structures were found to be related with loading degree. • PNBD–MMT nanocomposites had a higher thermal degradation temperature and lower dielectric constant

Application of a mixed metal oxide catalyst to a metallic substrate

Science.gov (United States)

Sevener, Kathleen M. (Inventor); Lohner, Kevin A. (Inventor); Mays, Jeffrey A. (Inventor); Wisner, Daniel L. (Inventor)

2009-01-01

A method for applying a mixed metal oxide catalyst to a metallic substrate for the creation of a robust, high temperature catalyst system for use in decomposing propellants, particularly hydrogen peroxide propellants, for use in propulsion systems. The method begins by forming a prepared substrate material consisting of a metallic inner substrate and a bound layer of a noble metal intermediate. Alternatively, a bound ceramic coating, or frit, may be introduced between the metallic inner substrate and noble metal intermediate when the metallic substrate is oxidation resistant. A high-activity catalyst slurry is applied to the surface of the prepared substrate and dried to remove the organic solvent. The catalyst layer is then heat treated to bind the catalyst layer to the surface. The bound catalyst layer is then activated using an activation treatment and calcinations to form the high-activity catalyst system.

Electrical and Photo-Induced Degradation of ZnO Layers in Organic Photovoltaics

DEFF Research Database (Denmark)

Manor, Assaf; Katz, Eugene A.; Tromholt, Thomas

2011-01-01

minutes) does not affect the short-circuit current of the device. However, a significant degradation of V-OC and FF has been recorded by measurements of the cell current-voltage curves with a variation of light intensity, for the devices before and after the treatment. The same degradation was found......We present the case of degradation of organic solar cells by sunlight concentrated to a moderate level (similar to 4 suns). This concentration level is not enough for sufficient acceleration of the photobleaching or trap-generation in the photoactive layer and therefore such short treatment (100...

Graphitic Layer Encapsulated Iron Based Non‐precious Catalysts for the Oxygen Reduction Reaction

DEFF Research Database (Denmark)

Zhong, Lijie

consisting of uniform metallic nanoparticles encapsulated in graphitic layers. The thesis work is conducted aiming at three major objectives: further optimization of the pyrolysis to achieve improved performance of catalysts, investigation of the complex Fe-containing components, and exploration...... of the nitrogen functionalities. Two anions in the electrolyte are used to probe the iron containing active sites towards the ORR, cyanide (CN-) in alkaline and thiocyanate (SCN-) in acidic medium, which seem supporting the above conclusions. These findings provide new insights to the encapsulation structure...

Homogeneous and heterogeneous catalysts of Fe3+, Co2+ and Cu2+ for the degradation of methyl parathion in diluted aqueous medium

Directory of Open Access Journals (Sweden)

Cindy A. Vela-Monroy

2016-07-01

Full Text Available Degradation of pesticides (plaguicides, herbicides, fungicides, among others in aqueous media is a subject of great importance for ensuring the water quality into numerous hydric sources. This work reports the assessment of homogeneous (metal ion solutions and heterogeneous (oxides supported on alumina systems that are based on Fe3+, Co2+ y Cu2+, which were used as catalysts for oxidation (degradation of methyl parathion (a plaguicide in aqueous solution. Hydrogen peroxide was herein used as oxidizing molecule under mild condition of reaction (25 ºC and atmospheric pressure. The solids were characterized by X-ray diffraction (XRD and scanning electron microscopy (SEM. Fe3+/H2O2 (Fenton system was the most active homogeneous catalyst compared to Co2+/H2O2 and Cu2+/H2O2 systems. Solids catalysts such as cobalt, copper or iron oxides as well as mixed oxides supported on alumina were active at pH close to neutrality. Fe-Co-Cu/Al2O3, Co-Cu/Al2O3 and FeCo/Al2O3 mixed systems were solids with the highest catalytic activity. In addition, an important effect of the support (-Al2O3 on the reaction pH was observed, allowing to reach values close to that of the neutrality, and thus increasing the catalytic activity of both cobalt oxide and copper oxide species. These results allow advancing on a new pathway for searching catalysts to remove organophosphorous pesticides from residual waters.

Photocatalytic activity of porous multiwalled carbon nanotube-TiO{sub 2} composite layers for pollutant degradation

Energy Technology Data Exchange (ETDEWEB)

Zouzelka, Radek [J. Heyrovsky Institute of Physical Chemistry, v.i.i., Academy of Sciences of the Czech Republic, Dolejskova 3, 18223 Prague 8 (Czech Republic); Department of Physical Chemistry, University of Chemistry and Technology Prague, 16628 Prague (Czech Republic); Kusumawati, Yuly [Chimie ParisTech, PSL Research University, CNRS, Institut de Recherche de Chimie Paris (IRCP), 11 rue Pierre et Marie Curie, 75005 Paris (France); Remzova, Monika [J. Heyrovsky Institute of Physical Chemistry, v.i.i., Academy of Sciences of the Czech Republic, Dolejskova 3, 18223 Prague 8 (Czech Republic); Department of Physical Chemistry, University of Chemistry and Technology Prague, 16628 Prague (Czech Republic); Rathousky, Jiri [J. Heyrovsky Institute of Physical Chemistry, v.i.i., Academy of Sciences of the Czech Republic, Dolejskova 3, 18223 Prague 8 (Czech Republic); Pauporté, Thierry, E-mail: thierry.pauporte@chimie-paristech.fr [Chimie ParisTech, PSL Research University, CNRS, Institut de Recherche de Chimie Paris (IRCP), 11 rue Pierre et Marie Curie, 75005 Paris (France)

2016-11-05

Highlights: • A simple method for TiO{sub 2}/graphene nanocomposite layer preparation. • Stable coatings on glass substrate. • Mesoporous nanocomposite films with high internal surface area. • High photoactivity for 4-chlorophenol degradation. • Analysis of photocatalysis enhancement mechanism. - Abstract: TiO{sub 2} nanoparticles are suitable building blocks nanostructures for the synthesis of porous functional thin films. Here we report the preparation of films using brookite, P25 titania and anatase pristine nanoparticles and of nanocomposite layers combining anatase nanoparticles and multi-walled carbon nanotube (MWCNT) at various concentrations. The structure and phase composition of the layers were characterized by X-ray diffraction and Raman spectroscopy. Their morphology and texture properties were determined by scanning electron microscopy and krypton adsorption experiments, respectively. Additionally to a strong absorption in the UV range, the composites exhibited light absorption in the visible range as well. The photocatalytic performance of the layers was tested in the degradation of aqueous solutions of 4-chlorophenol serving as a model of an eco-persistent pollutant. Besides the determination of the decrease in the concentration of 4-chlorophenol, also the formation of intermediate degradation products, namely hydroquinone and benzoquinone, was followed. The presence of MWCNTs had a beneficial effect on the photocatalytic performance, a marked increase in the photocatalytic degradation rate constant being observed even at very low concentrations of MWCNTs. Compared to a P25 reference layer, the first order rate reaction constant increased by about 100% for the composite films containing MWCNTs at concentrations above 0.6 wt%. The key parameters for the enhancement of the photocatalytic performance are discussed. The presence of carbon nanotubes influences beneficially the degradation of 4-chlorophenol by an attack of the primarily

Synthesis of Poly(3,4-Ethylenedioxy thiophene)-Poly(Styrene-4-Sulfonate) Composites for Support Fuel Cell Catalyst Layer

International Nuclear Information System (INIS)

Eko Sulistiyono; Murni Handayani

2009-01-01

Synthesis of poly(3,4-ethylenedioxy thiophene)-poly(styrene-4-sulfonate) composites for support fuel cell catalyst layer are synthesis composites which become fuel cell catalyst support so that catalyst has optimal performance. Main function of composites is support platinum particle for application in fuel cell. This article explains the result of composites production process from ( 3,4 Ethylenedioxy thiophene) and Sodium poly( styrene - 4-sulfonate) using two methods Jingning Shan method (method 1) and Zhigang Qi and Peter G.Pickup method (method 2). Analysis of the synthesis results used Scanning Electron Microscopic –Electron Dispersive X – Ray Spectrophotometer (SEM-EDS ). The analysis result show that both methods produce polymer agglomerate into a sponge-like morphology. Composite from method 1 has morphology, pores and proton transport better than composite produced by method 2. (author)

The Enhanced Catalytic Performance and Stability of Rh/γ-Al2O3 Catalyst Synthesized by Atomic Layer Deposition (ALD for Methane Dry Reforming

Directory of Open Access Journals (Sweden)

Yunlin Li

2018-01-01

Full Text Available Rh/γ-Al2O3 catalysts were synthesized by both incipient wetness impregnation (IWI and atomic layer deposition (ALD. The TEM images of the two catalysts showed that the catalyst from ALD had smaller particle size, and narrower size distribution. The surface chemical states of both catalysts were investigated by both XPS and X-ray Absorption Near Edge Structure (XANES, and the catalyst from IWI had higher concentration of Rh3+ than that from ALD. The catalytic performance of both catalysts was tested in the dry reforming of methane reaction. The catalyst from ALD showed a higher conversion and selectivity than that from IWI. The stability testing results indicated that the catalyst from ALD showed similar stability to that from IWI at 500 °C, but higher stability at 800 °C.

Liquefaction of kraft lignin by hydrocracking with simultaneous use of a novel dual acid-base catalyst and a hydrogenation catalyst.

Science.gov (United States)

Wang, Jindong; Li, Wenzhi; Wang, Huizhen; Ma, Qiaozhi; Li, Song; Chang, Hou-Min; Jameel, Hasan

2017-11-01

In this study, a novel catalyst, S 2 O 8 2- -KNO 3 /TiO 2 , which has active acidic and basic sites, was prepared and used in lignin hydrocracking with a co-catalyst, Ru/C. Ru/C is an efficient hydrogenation catalyst and S 2 O 8 2- -KNO 3 /TiO 2 is a dual catalyst, which could efficiently degrade lignin. This catalytic hydrogenation system can reduce solid products to less than 1%, while giving a high liquid product yield of 93%. Catalytic hydrocracking of kraft lignin at 320°C for 6h gave 93% liquid product with 0.5% solid product. Most of this liquid product was soluble in petroleum ether (60% of 93%), which is a clear liquid and comprises mainly of monomeric and dimeric degradation products. These results demonstrated that the combination of the two catalysts is an efficient catalyst for liquefaction of lignin, with little char formation (∼1%). This concept has the potential to produce valuable chemicals and fuels from lignin under moderate conditions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Natural Hematite and Siderite as Heterogeneous Catalysts for an Effective Degradation of 4-Chlorophenol via Photo-Fenton Process

Directory of Open Access Journals (Sweden)

Haithem Bel Hadjltaief

2018-06-01

Full Text Available This paper describes a simple and low-cost process for the degradation of 4-Chlorophenol (4-CP from aqueous solution, using natural Tunisian Hematite (M1 and Siderite (M2. Two natural samples were collected in the outcroppings of the Djerissa mining site (Kef district, northwestern Tunisia. Both Hematite and Siderite ferrous samples were characterized using several techniques, including X-Ray Diffraction (XRD, Nitrogen Physisorption (BET, Infrared Spectroscopy (FTIR, H2-Temperature Programmed Reduction (H2-TPR, Scanning Electronic Microscopy (SEM linked with Energy Dispersive X-ray (EDS and High-Resolution Transmission Electron Microscopy (HRTEM. Textural, structural and chemical characterization confirmed the presence of Hematite and Siderite phases with a high amount of iron on the both surface materials. Their activity was evaluated in the oxidation of 4-CP in aqueous medium under heterogeneous photo-Fenton process. Siderite exhibited higher photocatalytic oxidation activity than Hematite at pH 3. The experimental results also showed that 100% conversion of 4-CP and 54% TOC removal can be achieved using Siderite as catalyst. Negligible metal leaching and catalyst reutilization without any loss of activity point towards an excellent catalytic stability for both natural catalysts.

Catalytic wet air oxidation of coke-plant wastewater on ruthenium-based eggshell catalysts in a bubbling bed reactor.

Science.gov (United States)

Yang, M; Sun, Y; Xu, A H; Lu, X Y; Du, H Z; Sun, C L; Li, C

2007-07-01

Catalytic wet air of coke-plant wastewater was studied in a bubbling bed reactor. Two types of supported Ru-based catalysts, eggshell and uniform catalysts, were employed. Compared with the results in the wet air oxidation of coke-plant wastewater, supported Ru uniform catalysts showed high activity for chemical oxygen demand (COD) and ammonia/ammonium compounds (NH3-N) removal at temperature of 250 degrees C and pressure of 4.8 MPa, and it has been demonstrated that the catalytic activity of uniform catalyst depended strongly on the distribution of active sites of Ru on catalyst. Compared to the corresponding uniform catalysts with the same Ru loading (0.25 wt.% and 0.1 wt.%, respectively), the eggshell catalysts showed higher activities for CODcr removal and much higher activities for NH3-N degradation. The high activity of eggshell catalyst for treatment of coke-plant wastewater can be attributed to the higher density of active Ru sites in the shell layer than that of the corresponding uniform catalyst with the same Ru loading. It has been also evidenced that the active Ru sites in the internal core of uniform catalyst have very little or no contribution to CODcr and NH3-N removal in the total oxidation of coke-plant wastewater.

Atomic diffusion induced degradation in bimetallic layer coated cemented tungsten carbide

International Nuclear Information System (INIS)

Peng, Zirong; Rohwerder, Michael; Choi, Pyuck-Pa; Gault, Baptiste; Meiners, Thorsten; Friedrichs, Marcel; Kreilkamp, Holger; Klocke, Fritz; Raabe, Dierk

2017-01-01

Highlights: • We study the temporal degradation of PtIr/Cr/WC and PtIr/Ni/WC systems. • Short cut diffusion, segregation, oxidation and interdiffusion reactions occurred. • Outward diffusion of Cr (Ni) via PtIr grain boundaries triggered the degradation. • The microstructure of the PtIr layer controlled the systems stability. • We propose an atomic diffusion induced degradation mechanism. - Abstract: We investigated the temporal degradation of glass moulding dies, made of cemented tungsten carbide coated with PtIr on an adhesive Cr or Ni interlayer, by electron microscopy and atom probe tomography. During the exposure treatments at 630 °C under an oxygen partial pressure of 1.12 × 10"−"2"3 bar, Cr (Ni) was found to diffuse outwards via grain boundaries in the PtIr, altering the surface morphology. Upon dissolution of the interlayer, the WC substrate also started degrading. Extensive interdiffusion processes involving PtIr, Cr (Ni) and WC took place, leading to the formation of intermetallic phases and voids, deteriorating the adhesion of the coating.

W-containing oxide layers obtained on aluminum and titanium by PEO as catalysts in thiophene oxidation

Science.gov (United States)

Rudnev, V. S.; Lukiyanchuk, I. V.; Vasilyeva, M. S.; Morozova, V. P.; Zelikman, V. M.; Tarkhanova, I. G.

2017-11-01

W-containing oxide layers fabricated on titanium and aluminum alloys by Plasma electrolytic oxidation (PEO) have been tested in the reaction of the peroxide oxidation of thiophene. Samples with two types of coatings have been investigated. Coatings I contained tungsten oxide in the matrix and on the surface of amorphous silica-titania or silica-alumina layers, while coatings II comprised crystalline WO3 and/or Al2(WO4)3. Aluminum-supported catalyst containing a smallest amount of transition metals in the form of tungsten oxides and manganese oxides in low oxidation levels showed high activity and stability.

Improvement of performance in low temperature solid oxide fuel cells operated on ethanol and air mixtures using Cu-ZnO-Al2O3 catalyst layer

Science.gov (United States)

Morales, M.; Espiell, F.; Segarra, M.

2015-10-01

Anode-supported single-chamber solid oxide fuel cells with and without Cu-ZnO-Al2O3 catalyst layers deposited on the anode support have been operated on ethanol and air mixtures. The cells consist of gadolinia-doped ceria electrolyte, Ni-doped ceria anode, and La0.6Sr0.4CoO3-δ-doped ceria cathode. Catalyst layers with different Cu-ZnO-Al2O3 ratios are deposited and sintered at several temperatures. Since the performance of single-chamber fuel cells strongly depends on catalytic properties of electrodes for partial oxidation of ethanol, the cells are electrochemically characterized as a function of the temperature, ethanol-air molar ratio and gas flow rate. In addition, catalytic activities of supported anode, catalytic layer-supported anode and cathode for partial oxidation of ethanol are analysed. Afterwards, the effect of composition and sintering temperature of catalyst layer on the cell performance are determined. The results indicate that the cell performance can be significantly enhanced using catalyst layers of 30:35:35 and 40:30:30 wt.% Cu-ZnO-Al2O3 sintered at 1100 °C, achieving power densities above 50 mW cm-2 under 0.45 ethanol-air ratio at temperatures as low as 450 °C. After testing for 15 h, all cells present a gradual loss of power density, without carbon deposition, which is mainly attributed to the partial re-oxidation of Ni at the anode.

Design of porous nanostructured solid catalysts

DEFF Research Database (Denmark)

Abildstrøm, Jacob Oskar

cells, as a mean to transform chemical as the main technique explained. The chapter will also cover degradation mechanisms of the catalyst employed in PEMFC, such as carbon corrosion and particle agglomeration. Strategies on how to increase resistance towards these degradation mechanisms...

Catalyst synthesis and evaluation using an integrated atomic layer deposition synthesis–catalysis testing tool

International Nuclear Information System (INIS)

Camacho-Bunquin, Jeffrey; Shou, Heng; Marshall, Christopher L.; Aich, Payoli; Beaulieu, David R.; Klotzsch, Helmut; Bachman, Stephen; Hock, Adam; Stair, Peter

2015-01-01

An integrated atomic layer deposition synthesis-catalysis (I-ALD-CAT) tool was developed. It combines an ALD manifold in-line with a plug-flow reactor system for the synthesis of supported catalytic materials by ALD and immediate evaluation of catalyst reactivity using gas-phase probe reactions. The I-ALD-CAT delivery system consists of 12 different metal ALD precursor channels, 4 oxidizing or reducing agents, and 4 catalytic reaction feeds to either of the two plug-flow reactors. The system can employ reactor pressures and temperatures in the range of 10 −3 to 1 bar and 300–1000 K, respectively. The instrument is also equipped with a gas chromatograph and a mass spectrometer unit for the detection and quantification of volatile species from ALD and catalytic reactions. In this report, we demonstrate the use of the I-ALD-CAT tool for the synthesis of platinum active sites and Al 2 O 3 overcoats, and evaluation of catalyst propylene hydrogenation activity

Catalyst synthesis and evaluation using an integrated atomic layer deposition synthesis–catalysis testing tool

Energy Technology Data Exchange (ETDEWEB)

Camacho-Bunquin, Jeffrey; Shou, Heng; Marshall, Christopher L. [Chemical Sciences and Engineering Division, Argonne National Laboratory, Lemont, Illinois 60439 (United States); Aich, Payoli [Chemical Sciences and Engineering Division, Argonne National Laboratory, Lemont, Illinois 60439 (United States); Department of Chemical Engineering, University of Illinois at Chicago, Chicago, Illinois 60607 (United States); Beaulieu, David R.; Klotzsch, Helmut; Bachman, Stephen [Arradiance Inc., Sudbury, Massachusetts 01776 (United States); Hock, Adam [Chemical Sciences and Engineering Division, Argonne National Laboratory, Lemont, Illinois 60439 (United States); Department of Chemistry, Illinois Institute of Technology, Chicago, Illinois 60616 (United States); Stair, Peter [Chemical Sciences and Engineering Division, Argonne National Laboratory, Lemont, Illinois 60439 (United States); Department of Chemistry, Northwestern University, Evanston, Illinois 60208 (United States)

2015-08-15

An integrated atomic layer deposition synthesis-catalysis (I-ALD-CAT) tool was developed. It combines an ALD manifold in-line with a plug-flow reactor system for the synthesis of supported catalytic materials by ALD and immediate evaluation of catalyst reactivity using gas-phase probe reactions. The I-ALD-CAT delivery system consists of 12 different metal ALD precursor channels, 4 oxidizing or reducing agents, and 4 catalytic reaction feeds to either of the two plug-flow reactors. The system can employ reactor pressures and temperatures in the range of 10{sup −3} to 1 bar and 300–1000 K, respectively. The instrument is also equipped with a gas chromatograph and a mass spectrometer unit for the detection and quantification of volatile species from ALD and catalytic reactions. In this report, we demonstrate the use of the I-ALD-CAT tool for the synthesis of platinum active sites and Al{sub 2}O{sub 3} overcoats, and evaluation of catalyst propylene hydrogenation activity.

Degradation of Paracetamol by Photolysis Using C-N-codoped TiO2

Directory of Open Access Journals (Sweden)

Vanny Yulia Safitri

2017-11-01

Full Text Available Paracetamol is generally used as analgesic and antipyretic drugs. Contamination paracetamol in the environment can occur because of waste material disposal from production site and immediate disposal of household that cause water pollution. Paracetamol is degraded by photolysis method under irradiation 10 watt UV-light (λ=365 nm, visible-light (Philips LED 13 watt 1400 lux and solar-light with and without addition C-N-codoped TiO2catalyst. The solution is analyzed by UV-Vis spectrophotometer at λ 200-400 nm. Optimum weight of C-N-codoped TiO2 catalyst obtained is 20 mg under UV-light photolysis. Paracetamol 4 mg/L is degraded 45.48% after 120 minutes under UV-light irradiation without catalyst, and increases to be 69.31% by using 20 mg catalyst. While degradation percentage of paracetamol is 16.96 % without catalyst, the percentage increases to be 34.29% after using 20 mg catalyst for 120 minutes photolysis under visible-light. Degradation of paracetamol by solar light achieves only 12.27% in absance of catalyst for 120 minutes irradiation, but it increases significantly until 70.39% in presence of 20 mg catalyst.

Simple preparation of Fenton catalyst@bacterial cellulose for waste water treatment

Science.gov (United States)

Wibowo, Arie; Febi Indrawan, Radian; Triadhi, Untung; Hasdi Aimon, Akfiny; Iskandar, Ferry; Ardy, Husaini

2018-02-01

Heterogeneous fenton catalyst is one of the attractive technologies for destruction of persistent and non-biodegradable pollutant in wastewater, because it can be used in wide range of pH and recyclable. Herein, commercial bacterial celluloses (BCs) were used as an alternative support of fenton catalyst to improve their catalytic activity. Scanning Electron Microscope (SEM) observations indicated that the presence of BCs and decreasing precursor concentration might promote formation of smaller particle sizes of catalyst from 3.5 μm of bare catalyst to 0.7 μm of catalyst@BC. UV-vis measurement showed that fast degradation of dyes with half-time degradation at around 25 min was observed in sample using catalyst@BCs with precursor concentration of 0.01 M. Successful preparation of heterogeneous fenton catalyst with smaller particle size and better catalytic activity is important for their application in wastewater treatment.

Lattice Boltzmann Pore-Scale Investigation of Coupled Physical-electrochemical Processes in C/Pt and Non-Precious Metal Cathode Catalyst Layers in Proton Exchange Membrane Fuel Cells

International Nuclear Information System (INIS)

Chen, Li; Wu, Gang; Holby, Edward F; Zelenay, Piotr; Tao, Wen-Quan; Kang, Qinjun

2015-01-01

Highlights: • Nanoscale structures of catalyst layer are reconstructed. • Pore-scale simulation is performed to predict macroscopic transport properties. • Reactive transport in catalyst layer with non-precious metal and Pt catalysts is studied. • Mesopores rather than micropores are required to enhance mass transport. - Abstract: High-resolution porous structures of catalyst layers (CLs) including non-precious metal catalysts (NPMCs) or Pt for proton exchange membrane fuel cells are reconstructed using the quartet structure generation set. The nanoscale structures are analyzed in terms of pore size distribution, specific surface area, and phase connectivity. Pore-scale simulation methods based on the lattice Boltzmann method are developed to predict the macroscopic transport properties in CLs. The non-uniform distribution of ionomer in CL generates more tortuous pathways for reactant transport, greatly reducing the effective diffusivity. The tortuosity of CLs is much higher than that adopted by the Bruggeman equation. Knudsen diffusion plays a significant role in oxygen diffusion and significantly reduces the effective diffusivity. Reactive transport inside the CLs is also investigated. Although the reactive surface area of the non-precious metal catalyst (NPMC) CL is much higher than that of the Pt CL, the oxygen reaction rate is lower in the NPMC CL due to the much lower reaction rate coefficient. Although pores of a few nanometers in size can increase the number of reactive sites in NPMC CLs, they contribute little to enhance the mass transport. Mesopores, which are a few tens of nanometers or larger in size, are shown to be required in order to increase the mass transport rate

Timing is everything: early degradation of abscission layer is associated with increased seed shattering in U.S. weedy rice

Directory of Open Access Journals (Sweden)

Hepler Peter K

2011-01-01

Full Text Available Abstract Background Seed shattering, or shedding, is an important fitness trait for wild and weedy grasses. U.S. weedy rice (Oryza sativa is a highly shattering weed, thought to have evolved from non-shattering cultivated ancestors. All U.S. weedy rice individuals examined to date contain a mutation in the sh4 locus associated with loss of shattering during rice domestication. Weedy individuals also share the shattering trait with wild rice, but not the ancestral shattering mutation at sh4; thus, how weedy rice reacquired the shattering phenotype is unknown. To establish the morphological basis of the parallel evolution of seed shattering in weedy rice and wild, we examined the abscission layer at the flower-pedicel junction in weedy individuals in comparison with wild and cultivated relatives. Results Consistent with previous work, shattering wild rice individuals possess clear, defined abscission layers at flowering, whereas non-shattering cultivated rice individuals do not. Shattering weedy rice from two separately evolved populations in the U.S. (SH and BHA show patterns of abscission layer formation and degradation distinct from wild rice. Prior to flowering, the abscission layer has formed in all weedy individuals and by flowering it is already degrading. In contrast, wild O. rufipogon abscission layers have been shown not to degrade until after flowering has occurred. Conclusions Seed shattering in weedy rice involves the formation and degradation of an abscission layer in the flower-pedicel junction, as in wild Oryza, but is a developmentally different process from shattering in wild rice. Weedy rice abscission layers appear to break down earlier than wild abscission layers. The timing of weedy abscission layer degradation suggests that unidentified regulatory genes may play a critical role in the reacquisition of shattering in weedy rice, and sheds light on the morphological basis of parallel evolution for shattering in weedy and wild

UV and visible activation of Cr(III)-doped TiO2 catalyst prepared by a microwave-assisted sol-gel method during MCPA degradation.

Science.gov (United States)

Mendiola-Alvarez, S Y; Guzmán-Mar, J L; Turnes-Palomino, G; Maya-Alejandro, F; Hernández-Ramírez, A; Hinojosa-Reyes, L

2017-05-01

Photocatalytic degradation of 4-chloro-2-methylphenoxyacetic acid (MCPA) in aqueous solution using Cr(III)-doped TiO 2 under UV and visible light was investigated. The semiconductor material was synthesized by a microwave-assisted sol-gel method with Cr(III) doping contents of 0.02, 0.04, and 0.06 wt%. The catalyst was characterized using X-ray powder diffraction (XRD), scanning electron microscopy (SEM), nitrogen physisorption, UV-Vis diffuse reflectance spectroscopy (DRS), and atomic absorption spectroscopy (AAS). The photocatalytic activity for the photodegradation of MCPA was followed by reversed-phase high-performance liquid chromatography (HPLC) and total organic carbon (TOC) analysis. The intermediates formed during degradation were identified using gas chromatography-mass spectrometry (GC-MS). Chloride ion evolution was measured by ion chromatography. Characterization results showed that Cr(III)-doped TiO 2 materials possessed a small crystalline size, high surface area, and mesoporous structure. UV-Vis DRS showed enhanced absorption in the visible region as a function of the Cr(III) concentration. The Cr(III)-doped TiO 2 catalyst with 0.04 wt% of Cr(III) was more active than bare TiO 2 for the degradation of MCPA under both UV and visible light. The intermediates identified during MCPA degradation were 4-chloro-2-methylphenol (CMP), 2-(4-hydroxy-2-methylphenoxy) acetic acid (HMPA), and 2-hydroxybuta-1,3-diene-1,4-diyl-bis (oxy)dimethanol (HBDM); the formation of these intermediates depended on the radiation source.

Identical location transmission electron microscopy in combination with rotating disc electrode measurements. The activity of fuel cell catalysts and their degradation

Energy Technology Data Exchange (ETDEWEB)

Schloegl, Katrin G.

2011-07-13

As an alternative to conventional combustion engines, the Proton Exchange Membrane Fuel Cell (PEMFC) using hydrogen as a fuel is a promising concept owing to its potential independence from fossil fuels, high efficiency and zero emissions. Concerning its commercial viability, the fundamental problem of high system cost per power output and lifetime is closely related to finding more active and stable catalysts for the oxygen reduction reaction. In the presented work, several methods are combined to examine the parameters and processes responsible for both activity and degradation of platinum-based catalysts. Degradation mechanisms are scrutinized by means of electrochemical measurements with the rotating disc electrode in combination with a recently developed TEM technique, which allows for the comparison of identical locations before and after accelerated stress tests. (orig.) [German] Die mit Wasserstoff betriebene Proton Exchange Membrane Brennstoffzelle (PEMFC) stellt aufgrund ihrer potentiellen Unabhaengigkeit von fossilen Energietraegern, ihrem hohen Wirkungsgrad und fehlendem Schadstoffausstoss eine vielversprechende Alternative zum konventionellen Verbrennungsmotor dar. Das grundlegende Problem der zu hohen Systemkosten und zu geringen Lebensdauer fuer kommerzielle Anwendungen ist eng mit der Entwicklung aktiverer und stabiler Elektrokatalysatoren fuer die Sauerstoffreduktion verknuepft. In der vorliegenden Arbeit werden verschiedene Methoden kombiniert, um die Parameter und Prozesse zu untersuchen, welche fuer die Aktivitaet und Degradation platinbasierter Katalysatoren verantwortlich sind. Zur Aufklaerung vorliegender Degradationsmechanismen werden elektrochemische Messungen mit der rotierenden Scheibenelektrode in Kombination mit einer neu entwickelten TEM Methode eingesetzt, welche es ermoeglicht, identische Stellen vor und nach beschleunigten Degradationstests zu untersuchen.

Recent Advances in Solid Catalysts Obtained by Metalloporphyrins Immobilization on Layered Anionic Exchangers: A Short Review and Some New Catalytic Results

Directory of Open Access Journals (Sweden)

Shirley Nakagaki

2016-02-01

Full Text Available Layered materials are a very interesting class of compounds obtained by stacking of two-dimensional layers along the basal axis. A remarkable property of these materials is their capacity to interact with a variety of chemical species, irrespective of their charge (neutral, cationic or anionic. These species can be grafted onto the surface of the layered materials or intercalated between the layers, to expand or contract the interlayer distance. Metalloporphyrins, which are typically soluble oxidation catalysts, are examples of molecules that can interact with layered materials. This work presents a short review of the studies involving metalloporphyrin immobilization on two different anionic exchangers, Layered Double Hydroxides (LDHs and Layered Hydroxide Salts (LHSs, published over the past year. After immobilization of anionic porphyrins, the resulting solids behave as reusable catalysts for heterogeneous oxidation processes. Although a large number of publications involving metalloporphyrin immobilization on LDHs exist, only a few papers have dealt with LHSs as supports, so metalloporphyrins immobilized on LHSs represent a new and promising research field. This work also describes new results on an anionic manganese porphyrin (MnP immobilized on Mg/Al-LDH solids with different nominal Mg/Al molar ratios (2:1, 3:1 and 4:1 and intercalated with different anions (CO32− or NO3−. The influence of the support composition on the MnP immobilization rates and the catalytic performance of the resulting solid in cyclooctene oxidation reactions will be reported.

Recent Advances in Solid Catalysts Obtained by Metalloporphyrins Immobilization on Layered Anionic Exchangers: A Short Review and Some New Catalytic Results.

Science.gov (United States)

Nakagaki, Shirley; Mantovani, Karen Mary; Machado, Guilherme Sippel; Castro, Kelly Aparecida Dias de Freitas; Wypych, Fernando

2016-02-29

Layered materials are a very interesting class of compounds obtained by stacking of two-dimensional layers along the basal axis. A remarkable property of these materials is their capacity to interact with a variety of chemical species, irrespective of their charge (neutral, cationic or anionic). These species can be grafted onto the surface of the layered materials or intercalated between the layers, to expand or contract the interlayer distance. Metalloporphyrins, which are typically soluble oxidation catalysts, are examples of molecules that can interact with layered materials. This work presents a short review of the studies involving metalloporphyrin immobilization on two different anionic exchangers, Layered Double Hydroxides (LDHs) and Layered Hydroxide Salts (LHSs), published over the past year. After immobilization of anionic porphyrins, the resulting solids behave as reusable catalysts for heterogeneous oxidation processes. Although a large number of publications involving metalloporphyrin immobilization on LDHs exist, only a few papers have dealt with LHSs as supports, so metalloporphyrins immobilized on LHSs represent a new and promising research field. This work also describes new results on an anionic manganese porphyrin (MnP) immobilized on Mg/Al-LDH solids with different nominal Mg/Al molar ratios (2:1, 3:1 and 4:1) and intercalated with different anions (CO₃(2-) or NO₃(-)). The influence of the support composition on the MnP immobilization rates and the catalytic performance of the resulting solid in cyclooctene oxidation reactions will be reported.

Direct dimethyl-ether (DME) synthesis by spatial patterned catalyst arrangement. A modeling and simulation study

Energy Technology Data Exchange (ETDEWEB)

McBride, K.; Turek, T.; Guettel, R. [Clausthal Univ. of Technology (Germany). Inst. of Chemical Process Engineering

2011-07-01

The effect of spatially patterned catalyst beds was investigated for direct DME synthesis from synthesis gas as an example. A layered arrangement of methanol synthesis and dehydration catalyst was chosen and studied by numerical simulation under typical operating conditions for single-step DME synthesis. It was revealed that catalyst layers significantly influence the DME productivity. With an increasing number of layers from 2 to 40, an increase in DME productivity was observed approaching the performance of a physical catalyst mixture for an infinite number of layers. The results prove that a physical mixture of methanol synthesis and dehydration catalyst achieves the highest DME productivity under operating conditions chosen in this study. This can be explained by the higher average methanol concentration for the layered catalyst arrangement and thus stronger equilibrium constraints for the methanol synthesis reaction. Essentially, the layered catalyst arrangement is comparable to a cascade model of the two-step process, which is less efficient in terms of DME yield than the single-step process. However, since a significant effect was found, the layered catalyst arrangement could be beneficial for other reaction systems. (orig.)

Natural polymers supported copper nanoparticles for pollutants degradation

Energy Technology Data Exchange (ETDEWEB)

Haider, Sajjad [Department of Chemical Engineering, College of Engineering, King Saud University, P.O. Box 800, Riyadh 11421 (Saudi Arabia); Kamal, Tahseen, E-mail: tkkhan@kau.edu.sa [Department of Chemistry, Faculty of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia); Center of Excellence for Advanced Materials Research (CEAMR), King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia); Khan, Sher Bahadar [Department of Chemistry, Faculty of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia); Center of Excellence for Advanced Materials Research (CEAMR), King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia); Omer, Muhammad [Institute of Chemical Sciences, University of Swat, Odigram, Swat, 19130, Khyber Pakhtunkhwa (Pakistan); Haider, Adnan [Department of Nano, Medical and Polymer Materials, College of Engineering, Yeungnam University, 280 Daehak-Ro, Gyeongsan 712-749 (Korea, Republic of); Khan, Farman Ullah; Asiri, Abdullah M. [Department of Chemistry, Faculty of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia); Center of Excellence for Advanced Materials Research (CEAMR), King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia)

2016-11-30

Highlights: • Chitosan (CS) coating layer was applied on the surface of cellulose microfibers mat (CMM). • The CS coating layer was used to uptake the Copper (Cu) ions which were converted to nanoparticles. • The Cu/CS-CMM was demonstrated as catalyst in nitrophenols and cresyl blue reductions. • The rate constants for 2-nitrophenol, 4-nitrophenol and cresyl blue were 1.2 × 10{sup −3} s{sup −1}, 2.1 × 10{sup −3} s {sup −1} and, 1.3 × 10{sup −3} s{sup −1}, respectively. • The used catalyst was easily recovered by just pulling the strip from solutions. - Abstract: In this report, chitosan (CS) was adhered on cellulose microfiber mat (CMM) to prepare CS-CMM. This was used as host for copper (Cu) nanoparticles preparation. After adsorption of Cu{sup 2+} ions from an aqueous solution of CuSO{sub 4}, the metal ions entrapped in CS coating layer was treated with sodium borohydride (NaBH{sub 4}) to prepare Cu nanoparticles loaded CS-CMM (Cu/CS-CMM). Fourier transform infrared spectroscopy, and X-ray diffraction confirmed the formation of Cu/CS-CMM hybrid. Scanning electron microscopy analysis was performed to reveal the morphology of the prepared catalyst. The prepared Cu/CS-CMM was employed as a catalyst for the degradation of nitro-aromatic compounds of 2-nitrophenol (2NP) and 4-nitrophenol (4NP) as well as an organic cresyl blue (CB) dye. Remarkably, the turnover frequency in the case of 2NP and 4NP using Cu/CS-CMM reaches 103.3 and 88.6 h{sup −1}, outperforming previously reported Cu nanoparticles immobilized in hydrogel-based catalytic systems. The rate constants for 2NP, 4NP and CB were 1.2 × 10{sup −3} s{sup −1}, 2.1 × 10{sup −3} s{sup −1} and, 1.3 × 10{sup −3} s{sup −1}, respectively. Besides, we discussed the separation of the catalyst from the reaction mixture and its re-usability.

Degradation of anionic surfactants using the reactor based on dielectric barrier discharge

Directory of Open Access Journals (Sweden)

Aonyas Munera Mustafa

2016-01-01

Full Text Available Two anionic surfactants (sodium lauryl sulfate - SDS and sodium dodecylbenzenesulfonate - SDBS were treated with dielectric barrier discharge. Loss of surfactant activity, decrease of chemical oxygen demand and total organic carbon as well as lower toxicity of degradation products were determined. Effects of catalysts - hydrogen peroxide and iron (II, on parameters mentioned above, were determined. Catalysts affect the degradation of SDBS and in the case of SDS catalysts have no effect on degradation. Both catalysts induce the decrease of COD and TOC values. Toxicity of solutions after the plasma treatment is lower in all the systems tested. [Projekat Ministarstva nauke Republike Srbije, br. OI 172030

Conversion of waste polystyrene through catalytic degradation into valuable products

Energy Technology Data Exchange (ETDEWEB)

Shah, Jasmin; Jan, Muhammad Rasul; Adnan [University of Peshawar, Peshawar (Pakistan)

2014-08-15

Waste expanded polystyrene (EPS) represents a source of valuable chemical products like styrene and other aromatics. The catalytic degradation was carried out in a batch reactor with a mixture of polystyrene (PS) and catalyst at 450 .deg. C for 30 min in case of Mg and at 400 .deg. C for 2 h both for MgO and MgCO{sub 3} catalysts. At optimum degradation conditions, EPS was degraded into 82.20±3.80 wt%, 91.60±0.20 wt% and 81.80±0.53 wt% liquid with Mg, MgO and MgCO{sub 3} catalysts, respectively. The liquid products obtained were separated into different fractions by fractional distillation. The liquid fractions obtained with three catalysts were compared, and characterized using GC-MS. Maximum conversion of EPS into styrene monomer (66.6 wt%) was achieved with Mg catalyst, and an increase in selectivity of compounds was also observed. The major fraction at 145 .deg. C showed the properties of styrene monomer. The results showed that among the catalysts used, Mg was found to be the most effective catalyst for selective conversion into styrene monomer as value added product.

Performance degradation and microstructure changes in freeze-thaw cycling for PEMFC MEAs with various initial microstructures

Energy Technology Data Exchange (ETDEWEB)

Lee, Sang-Yeop; Kim, Hyoung-Juhn; Cho, EunAe; Lee, Kug-Seung; Lim, Tae-Hoon; Jang, Jong Hyun [Fuel Cell Center, Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Hwang, In Chul [Corporate Research and Development Division, Hyundai-Kia Motors, Gyeonggi-do 446-912 (Korea, Republic of)

2010-12-15

When the temperature of a fuel cell vehicle is repeatedly reduced to subzero temperatures, volume changes by water/ice transformations and frost heave mechanism can cause microstructural changes in membrane-electrode assemblies (MEA), and a resultant permanent decrease in the performance of fuel cell stacks. In this study, five MEAs manufactured by different methods, were tested under repeated freeze-thaw (F-T) cycles between -20 C and 10 C, and the variations in their electrochemical and microstructural characteristics were analyzed according to the initial microstructures. When the MEAs were prepared by spraying catalyst inks on polymer membranes, no significant microstructural changes were observed. In the case of two supplied MEAs, void formations at the electrolyte/electrode interface or vertical cracks within the catalyst layers were observed after 120 F-T cycles. Void formation seems to be responsible for performance degradation as a result of ohmic loss, but the effect of cracks in the catalyst layers was not confirmed. In 120 F-T cycles, activation overpotentials and concentration overpotentials did not increase significantly for any of the MEAs, even although gradual decreases in the electrochemically active surface area of the platinum catalysts and changes in the porous structure were observed. (author)

Selective deposition of catalyst nanoparticles using the gravitational force for carbon nanotubes interconnect

Energy Technology Data Exchange (ETDEWEB)

Kim, Do-Yoon; Lee, Hyun-Chul; Lee, Jong-Hak; Park, Jae-Hong; Alegaonkar, Prashant S. [Center for Nanotubes and Nanostructured Composites, Sungkyunkwan University, 300 Chunchun-dong, Jangan-Gu, Suwon, 440-746 (Korea, Republic of); Yoo, Ji-Beom [Center for Nanotubes and Nanostructured Composites, Sungkyunkwan University, 300 Chunchun-dong, Jangan-Gu, Suwon, 440-746 (Korea, Republic of)], E-mail: jbyoo@skku.ac.kr; Han, In-Taek; Kim, Ha-Jin; Jin, Yong-Wan; Kim, Jong-Min [Samsung Advanced Institute of Technology, Mt. 14-1, Nongseo-dong, Giheung-gu, Younggin-si Gyunggi-do, 449-712 (Korea, Republic of); Kwon, Kee-Won [Department of Semiconducting System, Sungkyunkwan University (Korea, Republic of)

2008-04-01

The photolithography process has generally been used for the making of catalyst layers used for the synthesis of CNTs due to its comparative ease. However, this method results in the formation of undesirable catalyst particles, which deteriorate the quality of the devices. Therefore, we tried to form a catalyst layer without using any lift-off or wet etching process, especially for the formation of carbon nanotube interconnects. After spin coating the samples, which were previously fabricated with several vias, with an iron-acetate solution, the catalyst layer was pulled down into the bottom of the holes through the force of gravity. We were able to remove the catalyst layer which was coated over undesirable areas, by TMAH (tetramethylammonium hydroxide, N(CH{sub 3}){sub 4}OH) treatment. After the catalyst deposition process, we synthesized CNTs and observed them by scanning electron microscopy (SEM)

Fuel cell testing of Pt–Ru catalysts supported on differently prepared and pretreated carbon nanotubes

International Nuclear Information System (INIS)

Tokarz, Wojciech; Lota, Grzegorz; Frackowiak, Elzbieta; Czerwiński, Andrzej; Piela, Piotr

2013-01-01

Proton-exchange membrane fuel cell (PEMFC) testing of Pt–Ru catalysts supported on differently prepared multiwall carbon nanotube (MCNT) supports was performed to elucidate the influence of the different supports on the operating characteristics of the catalysts under real direct methanol fuel cell (DMFC) anode and H 2 -PEMFC anode conditions. The MCNTs were either thin, entangled or thick, disentangled. Pretreatment of the MCNTs was also done and it was either high-temperature KOH etching or annealing (graphitization). The performance of the catalysts was compared against the performance of a commercial Pt–Ru catalyst supported on a high-surface-area carbon black. Among the different MCNT supports, the graphitized, entangled support offered the best performance in all tests, which was equal to the performance of the commercial catalyst, despite the MCNT catalyst layer was ca. 2.2 times thicker than the carbon black catalyst layer. Even for an MCNT catalyst layer, which was almost 7 times thicker than the carbon black catalyst layer, the transport limitations were not prohibitive. This confirmed the expected potential of nanotube supports for providing superior reactant transport properties of the PEMFC catalyst layers

Biodegradable polymer for sealing porous PEO layer on pure magnesium: An in vitro degradation study

International Nuclear Information System (INIS)

Alabbasi, Alyaa; Mehjabeen, Afrin; Kannan, M. Bobby; Ye, Qingsong; Blawert, Carsten

2014-01-01

Graphical abstract: - Highlights: • Poly(L-lactide) was used to seal the porous PEO layer on Mg. • The dual-layer coating improved the in vitro degradation resistance of Mg. • Localized degradation was inhibited in the dual-layer coated Mg. - Abstract: An attempt was made to seal the porous silicate-based plasma electrolytic oxidation (PEO) layer on pure magnesium (Mg) with a biodegradable polymer, poly(L-lactide) (PLLA), to delay the localized degradation of magnesium-based implants in body fluid for better in-service mechanical integrity. Firstly, a silicate-based PEO coating on pure magnesium was performed using a pulsed constant current method. In order to seal the pores in the PEO layer, PLLA was coated using a two-step spin coating method. The performance of the PEO–PLLA Mg was evaluated using electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization. The EIS results showed that the polarization resistance (R p ) of the PEO–PLLA Mg was close to two orders of magnitude higher than that of the PEO Mg. While the corrosion current density (i corr ) of the pure Mg was reduced by 65% with the PEO coating, the PEO–PLLA coating reduced the i corr by almost 100%. As expected, the R p of the PEO–PLLA Mg decreased with increase in exposure time. However, it was noted that the R p of the PEO–PLLA Mg even after 100 h was six times higher than that of the PEO Mg after 48 h exposure, and did not show any visible localized attack

Biodegradable polymer for sealing porous PEO layer on pure magnesium: An in vitro degradation study

Energy Technology Data Exchange (ETDEWEB)

Alabbasi, Alyaa; Mehjabeen, Afrin [Biomaterials and Engineering Materials (BEM) Laboratory, James Cook University, Townsville 4811, Queensland (Australia); Kannan, M. Bobby, E-mail: bobby.mathan@jcu.edu.au [Biomaterials and Engineering Materials (BEM) Laboratory, James Cook University, Townsville 4811, Queensland (Australia); Ye, Qingsong [Discipline of Dentistry, James Cook University, Townsville 4811, Queensland (Australia); Blawert, Carsten [Magnesium Innovation Centre, Institute of Materials Research, Helmholtz-Zentrum Geesthacht, Geesthacht 21502 (Germany)

2014-05-01

Graphical abstract: - Highlights: • Poly(L-lactide) was used to seal the porous PEO layer on Mg. • The dual-layer coating improved the in vitro degradation resistance of Mg. • Localized degradation was inhibited in the dual-layer coated Mg. - Abstract: An attempt was made to seal the porous silicate-based plasma electrolytic oxidation (PEO) layer on pure magnesium (Mg) with a biodegradable polymer, poly(L-lactide) (PLLA), to delay the localized degradation of magnesium-based implants in body fluid for better in-service mechanical integrity. Firstly, a silicate-based PEO coating on pure magnesium was performed using a pulsed constant current method. In order to seal the pores in the PEO layer, PLLA was coated using a two-step spin coating method. The performance of the PEO–PLLA Mg was evaluated using electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization. The EIS results showed that the polarization resistance (R{sub p}) of the PEO–PLLA Mg was close to two orders of magnitude higher than that of the PEO Mg. While the corrosion current density (i{sub corr}) of the pure Mg was reduced by 65% with the PEO coating, the PEO–PLLA coating reduced the i{sub corr} by almost 100%. As expected, the R{sub p} of the PEO–PLLA Mg decreased with increase in exposure time. However, it was noted that the R{sub p} of the PEO–PLLA Mg even after 100 h was six times higher than that of the PEO Mg after 48 h exposure, and did not show any visible localized attack.

Transesterification of edible, non-edible and used cooking oils for biodiesel production using calcined layered double hydroxides as reusable base catalysts.

Science.gov (United States)

Sankaranarayanan, Sivashunmugam; Antonyraj, Churchil A; Kannan, S

2012-04-01

Fatty acid methyl esters (FAME) were produced from edible, non-edible and used cooking oils with different fatty acid contents by transesterification with methanol using calcined layered double hydroxides (LDHs) as solid base catalysts. Among the catalysts, calcined CaAl2-LDH (hydrocalumite) showed the highest activity with >90% yield of FAME using low methanol:oil molar ratio (<6:1) at 65 °C in 5 h. The activity of the catalyst was attributed to its high basicity as supported by Hammett studies and CO(2)-TPD measurements. The catalyst was successfully reused in up to four cycles. Some of the properties such as density, viscosity, neutralization number and glycerol content of the obtained biodiesel matched well with the standard DIN values. It is concluded that a scalable heterogeneously catalyzed process for production of biodiesel in high yields from a wide variety of triglyceride oils including used oils is possible using optimized conditions. Copyright © 2012 Elsevier Ltd. All rights reserved.

Silicon-depth profiling with Rutherford backscattering in photoresist layers; a study on the effects of degradation

NARCIS (Netherlands)

IJzendoorn, van L.J.; Schellekens, J.P.W.

1989-01-01

The reaction of a silicon-containing vapor with a photoresist layer, as used in some dry developable lithographic processes, was studied with Rutherford backscattering spectrometry. Degradation of the polymer layer under ion beam irradiation was observed, but it was found that this had no influence

Reclaim/recycle of Pt/C catalysts for PEMFC

International Nuclear Information System (INIS)

Zhao, Jishi; He, Xiangming; Tian, Jianhua; Wan, Chunrong; Jiang, Changyin

2007-01-01

Platinum was reclaimed from Pt/C catalysts of the PEMFC by drying the degraded Pt/C catalysts at 80 o C for 3 h, followed by sintering at 600 o C for 6 h, dissolution by aqua fortis, purification with hydrochloric acid, reduction and filtration, successively. Pt/C catalysts were prepared again from the reclaimed Pt by two proposed processes, e.g., pH value control process and mass control process. The fuel cell with recycled catalysts presented a power density of over 0.18 W cm -2 . The reclaiming of Pt/C catalysts is a potential way for recycling Pt for PEMFC, reducing the cost of PEMFC

Thermal conductivity of catalyst layer of polymer electrolyte membrane fuel cells: Part 1 - Experimental study

Science.gov (United States)

Ahadi, Mohammad; Tam, Mickey; Saha, Madhu S.; Stumper, Jürgen; Bahrami, Majid

2017-06-01

In this work, a new methodology is proposed for measuring the through-plane thermal conductivity of catalyst layers (CLs) in polymer electrolyte membrane fuel cells. The proposed methodology is based on deconvolution of bulk thermal conductivity of a CL from measurements of two thicknesses of the CL, where the CLs are sandwiched in a stack made of two catalyst-coated substrates. Effects of hot-pressing, compression, measurement method, and substrate on the through-plane thermal conductivity of the CL are studied. For this purpose, different thicknesses of catalyst are coated on ethylene tetrafluoroethylene (ETFE) and aluminum (Al) substrates by a conventional Mayer bar coater and measured by scanning electron microscopy (SEM). The through-plane thermal conductivity of the CLs is measured by the well-known guarded heat flow (GHF) method as well as a recently developed transient plane source (TPS) method for thin films which modifies the original TPS thin film method. Measurements show that none of the studied factors has any effect on the through-plane thermal conductivity of the CL. GHF measurements of a non-hot-pressed CL on Al yield thermal conductivity of 0.214 ± 0.005 Wṡm-1ṡK-1, and TPS measurements of a hot-pressed CL on ETFE yield thermal conductivity of 0.218 ± 0.005 Wṡm-1ṡK-1.

I. Hole-transporting dendrimers and their use in organic light-emitting devices (OLEDs) and II. Novel layered catalysts containing bipyridinium and zero-valent metal species

Science.gov (United States)

Koene, Shannon Carol

A series of polyaromatic ether/ester dendrimers containing a hole transporting naphthylphenylbenzyl amine at the periphery and a variety of fluorescent dyes at the core has been studied in an effort to observe energy transfer in these species. The dyes incorporated in these dendrimers include 1,4-dihydroxyanthraquinone (quinizarin), Coumarin 343, and a benzopentathiophene. These dendrimers have been incorporated into both single layer and heterostructure organic light emitting devices (OLEDs). In the case of first generation dendrimer OLEDs, excimer/exciplex formation was predominant. In third generation dendrimers, complete energy transfer from the periphery to the dye at the core was observed both in photoluminescence spectra and electroluminescence in OLEDs. Dendrimers containing different dye cores can be combined to achieve color mixing/tuning. In addition, layered catalysts were prepared via both covalent and electrostatic means to achieve the catalytic production of hydrogen peroxide from hydrogen and oxygen. Covalent catalysts were prepared by first growing layers of zirconium and a bipyridinium containing bisphosphonate onto silica particles. Palladium and/or platinum was ion-exchanged into the structure and reduced to the zero valent metal by hydrogen gas. A second set of catalysts was prepared by electrostatically depositing polycations/polyanions onto carboxylate or amine functionalized polystyrene microspheres. Anionic colloidal particles were adsorbed to the polycationic surface. An octacationic viologen oligomer was used in an attempt to increase the affinity of adsorption of the Pd particles to the surface of the microspheres. Catalytic studies of both types of catalysts are herein reported.

Carbonized tantalum catalysts for catalytic chemical vapor deposition of silicon films

Energy Technology Data Exchange (ETDEWEB)

Cheng Shimin [State Key Laboratory of Catalysis, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Dalian National Laboratory for Clean Energy, Dalian 116023 (China); Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Gao Huiping; Ren Tong; Ying Pinliang [State Key Laboratory of Catalysis, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Dalian National Laboratory for Clean Energy, Dalian 116023 (China); Li Can, E-mail: canli@dicp.ac.cn [State Key Laboratory of Catalysis, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Dalian National Laboratory for Clean Energy, Dalian 116023 (China)

2012-06-01

Catalytic chemical vapor deposition (Cat-CVD) has been demonstrated as a promising way to prepare device-quality silicon films. However, catalyst ageing due to Si contamination is an urgency to be solved for the practical application of the technique. In this study, the effect of carbonization of tantalum catalyst on its structure and performance was investigated. The carbonized Ta catalyst has a TaC surface layer which is preserved over the temperature range between 1450 and 1750 Degree-Sign C and no Si contamination occurs on the catalyst after long-term use. Si film prepared using the carbonized Ta catalyst has a similar crystal structure to that prepared by uncarbonized Ta catalyst. Formation of the TaC surface layer can alleviate the ageing problem of the catalyst, which shows great potential as a stable catalyst for Cat-CVD of Si films. - Highlights: Black-Right-Pointing-Pointer Si films prepared by catalytic chemical vapor deposition. Black-Right-Pointing-Pointer Carbonized Ta with a TaC surface layer used as catalyst. Black-Right-Pointing-Pointer TaC surface structure preserved after long-term use in a wide temperature range. Black-Right-Pointing-Pointer Help to solve the ageing problem of metal catalysts. Black-Right-Pointing-Pointer Si film obtained has a similar crystal structure to that prepared by Ta catalyst.

Influence of Ni Catalyst Layer and TiN Diffusion Barrier on Carbon Nanotube Growth Rate

Directory of Open Access Journals (Sweden)

Mérel Philippe

2010-01-01

Full Text Available Abstract Dense, vertically aligned multiwall carbon nanotubes were synthesized on TiN electrode layers for infrared sensing applications. Microwave plasma-enhanced chemical vapor deposition and Ni catalyst were used for the nanotubes synthesis. The resultant nanotubes were characterized by SEM, AFM, and TEM. Since the length of the nanotubes influences sensor characteristics, we study in details the effects of changing Ni and TiN thickness on the physical properties of the nanotubes. In this paper, we report the observation of a threshold Ni thickness of about 4 nm, when the average CNT growth rate switches from an increasing to a decreasing function of increasing Ni thickness, for a process temperature of 700°C. This behavior is likely related to a transition in the growth mode from a predominantly “base growth” to that of a “tip growth.” For Ni layer greater than 9 nm the growth rate, as well as the CNT diameter, variations become insignificant. We have also observed that a TiN barrier layer appears to favor the growth of thinner CNTs compared to a SiO2 layer.

TiO2 and Al2O3 promoted Pt/C nanocomposites as low temperature fuel cell catalysts for electro oxidation of methanol in acidic media

International Nuclear Information System (INIS)

Naeem, Rabia; Ahmed, Riaz; Ansari, Muhammad Shahid

2014-01-01

Carbon corrosion and platinum dissolution are the two major catalyst layer degradation problems in polymer electrolyte membrane fuel cells (PEMFC). Ceramic addition can reduce the corrosion of carbon and increase the stability of catalysts. Pt/TiO 2 , Pt/TiO 2 -C, Pt/Al 2 O 3 and Pt/Al 2 O 3 -C catalysts were synthesized and characterized. Electrochemical surface area of Pt/TiO 2 -C and Pt/Al 2 O 3 -C nanocomposite catalysts was much higher than the Pt/TiO 2 and Pt/Al 2 O 3 catalysts. Peak current, specific activity and mass activity of the catalysts was also determined by cyclic voltammetry and were much higher for the carbon nanocomposites. Exchange current densities were determined from Tafel plots. Heterogeneous rates of reaction of electro oxidation of methanol were determined for all the catalysts and were substantially higher for titania catalysts as compared to alumina added catalysts. Mass activity of Pt/TiO 2 -C was much higher than mass activity of Pt/Al 2 O 3 -C. Stability studies showed that addition of ceramics have increased the catalytic activity and durability of the catalysts considerably

PEMFC catalyst layers: the role of micropores and mesopores on water sorption and fuel cell activity.

Science.gov (United States)

Soboleva, Tatyana; Malek, Kourosh; Xie, Zhong; Navessin, Titichai; Holdcroft, Steven

2011-06-01

The effects of carbon microstructure and ionomer loading on water vapor sorption and retention in catalyst layers (CLs) of PEM fuel cells are investigated using dynamic vapor sorption. Catalyst layers based on Ketjen Black and Vulcan XC-72 carbon blacks, which possess distinctly different surface areas, pore volumes, and microporosities, are studied. It is found that pores <20 nm diameter facilitate water uptake by capillary condensation in the intermediate range of relative humidities. A broad pore size distribution (PSD) is found to enhance water retention in Ketjen Black-based CLs whereas the narrower mesoporous PSD of Vulcan CLs is shown to have an enhanced water repelling action. Water vapor sorption and retention properties of CLs are correlated to electrochemical properties and fuel cell performance. Water sorption enhances electrochemical properties such as the electrochemically active surface area (ESA), double layer capacitance and proton conductivity, particularly when the ionomer content is very low. The hydrophilic properties of a CL on the anode and the cathode are adjusted by choosing the PSD of carbon and the ionomer content. It is shown that a reduction of ionomer content on either cathode or anode of an MEA does not necessarily have a significant detrimental effect on the MEA performance compared to the standard 30 wt % ionomer MEA. Under operation in air and high relative humidity, a cathode with a narrow pore size distribution and low ionomer content is shown to be beneficial due to its low water retention properties. In dry operating conditions, adequate ionomer content on the cathode is crucial, whereas it can be reduced on the anode without a significant impact on fuel cell performance. © 2011 American Chemical Society

Degradation of organic dyes using spray deposited nanocrystalline stratified WO3/TiO2 photoelectrodes under sunlight illumination

Science.gov (United States)

Hunge, Y. M.; Yadav, A. A.; Mahadik, M. A.; Bulakhe, R. N.; Shim, J. J.; Mathe, V. L.; Bhosale, C. H.

2018-02-01

The need to utilize TiO2 based metal oxide hetero nanostructures for the degradation of environmental pollutants like Rhodamine B and reactive red 152 from the wastewater using stratified WO3/TiO2 catalyst under sunlight illumination. WO3, TiO2 and stratified WO3/TiO2 catalysts were prepared by a spray pyrolysis method. It was found that the stratified WO3/TiO2 heterostructure has high crystallinity, no mixed phase formation occurs, strong optical absorption in the visible region of the solar spectrum, and large surface area. The photocatalytic activity was tested for degradation of Rhodamine B (Rh B) and reactive red 152 in an aqueous medium. TiO2 layer in stratified WO3/TiO2 catalyst helps to extend its absorption spectrum in the solar light region. Rh B and Reactive red 152is eliminated up to 98 and 94% within the 30 and 40 min respectively at optimum experimental condition by stratified WO3/TiO2. Moreover, stratified WO3/TiO2 photoelectrode has good stability and reusability than individual TiO2 and WO3 thin film in the degradation of Rh B and reactive red 152. The photoelectrocatalytic experimental results indicate that stratified WO3/TiO2 photoelectrode is a promising material for dye removal.

Electroreduction of oxygen on carbon-supported gold catalysts

International Nuclear Information System (INIS)

Erikson, Heiki; Juermann, Gea; Sarapuu, Ave; Potter, Robert J.; Tammeveski, Kaido

2009-01-01

The electrochemical reduction of oxygen was studied on Au/C catalysts (20 and 30 wt%) in 0.5 M H 2 SO 4 and 0.1 M KOH solutions using the rotating disk electrode (RDE) method. The thickness of the Au/C-Nafion layers was varied between 1.5 and 10 μm. The specific activity of Au was independent of catalyst loading in both solutions, indicating that the transport of reactants through the catalyst layer does not limit the process of oxygen reduction under these conditions. The mass activity of 20 wt% Au/C catalysts was higher due to smaller particle size. The number of electrons involved in the reaction and the Tafel slopes were found; the values of these parameters are similar to that of bulk polycrystalline gold and indicate that the mechanism of O 2 reduction is not affected by carbon support or the catalyst configuration.

Photo-, sono- and sonophotocatalytic degradation of methylene blue using Fe3O4/ZrO2 composites catalysts

Science.gov (United States)

Kristianto, Y.; Taufik, A.; Saleh, R.

2017-07-01

In the present work, magnetite material Fe3O4/ZrO2 with various molar ratios was prepared by the two-step method (sol-gel followed by the ultrasonic-assisted method). The as-prepared samples were fairly characterized by various characterization methods, such as X-ray Diffraction (XRD), Vibrating Sample Magnetometer (VSM), Fourier Transform Infrared (FT-IR) and Thermal Gravimetric Analysis (TGA). The catalytic performance of the as-prepared samples was evaluated based on the degradation of methylene blue under UV light, ultrasound and combination of UV and ultrasound irradiation. The results revealed that the sample with Fe3O4:ZrO2 molar ratio of 0.5:1 showed the best catalytic performance under UV, ultrasound and UV + ultrasound irradiation. The degradation of methylene blue follows the order: sonophotocatalytic > sonocatalytic > photocatalytic. In addition, the effect of various scavengers has also been studied. Furthermore, all prepared samples could be used as a convenient recyclable catalyst.

Stimulated-healing of proton exchange membrane fuel cell catalyst

NARCIS (Netherlands)

Latsuzbaia, R.; Negro, E.; Koper, G.J.M.

2013-01-01

Platinum nanoparticles, which are used as catalysts in Proton Exchange Membrane Fuel Cells (PEMFC), tend to degrade after long-term operation. We discriminate the following mechanisms of the degradation: poisoning, migration and coalescence, dissolution, and electrochemical Ostwald ripening. There

Wafer scale integration of catalyst dots into nonplanar microsystems

DEFF Research Database (Denmark)

Gjerde, Kjetil; Kjelstrup-Hansen, Jakob; Gammelgaard, Lauge

2007-01-01

In order to successfully integrate bottom-up fabricated nanostructures such as carbon nanotubes or silicon, germanium, or III-V nanowires into microelectromechanical systems on a wafer scale, reliable ways of integrating catalyst dots are needed. Here, four methods for integrating sub-100-nm...... diameter nickel catalyst dots on a wafer scale are presented and compared. Three of the methods are based on a p-Si layer utilized as an in situ mask, an encapsulating layer, and a sacrificial window mask, respectively. All methods enable precise positioning of nickel catalyst dots at the end...

Thermal degradation kinetics of polyketone based on styrene and carbon monoxide

International Nuclear Information System (INIS)

Mu, Jiali; Fan, Wenjun; Shan, Shaoyun; Su, Hongying; Wu, Shuisheng; Jia, Qingming

2014-01-01

Highlights: • The PK were synthesized from carbon monoxide and styrene in the presence of PANI-PdCl 2 catalyst and PdCl 2 catalyst. • The structures and thermal behaviors of PK prepared by homogenous and the supported catalyst were investigated. • The microstructures of PK were changed in the supported catalyst system. • The alternating PK copolymer (PANI-PdCl 2 catalyst) was more thermally stable than PK (PdCl 2 catalyst). • The degradation activation energy values were estimated by Flynn–Wall–Ozawa method and Kissinger method. - Abstract: Copolymerization of styrene with carbon monoxide to give polyketones (PK) was carried out under homogeneous palladium catalyst and polyaniline (PANI) supported palladium(II) catalyst, respectively. The copolymers were characterized by 1 H NMR, 13 C NMR and GPC. The results indicated that the PK catalyzed by the supported catalyst has narrow molecular weight distribution (PDI = 1.18). For comparison purpose of thermal behaviors of PK prepared by the homogeneous and the supported catalyst, thermogravimetric (TG) analysis and derivative thermogravimetric (DTG) were conducted at different heating rates. The peak temperatures (396–402 °C) for PK prepared by the supported catalyst are higher than those (387–395 °C) of PK prepared by the homogeneous catalyst. The degradation activation energy (E k ) values were estimated by Flynn–Wall–Ozawa method and Kissinger method, respectively. The E k values, as determined by two methods, were found to be in the range 270.72 ± 0.03–297.55 ± 0.10 kJ mol −1 . Structures analysis and thermal degradation analysis revealed that the supported catalyst changed the microstructures of PK, resulting in improving thermal stability of PK

Thermal degradation kinetics of polyketone based on styrene and carbon monoxide

Energy Technology Data Exchange (ETDEWEB)

Mu, Jiali, E-mail: jiaqm411@163.com; Fan, Wenjun; Shan, Shaoyun; Su, Hongying; Wu, Shuisheng; Jia, Qingming

2014-03-01

Highlights: • The PK were synthesized from carbon monoxide and styrene in the presence of PANI-PdCl{sub 2} catalyst and PdCl{sub 2} catalyst. • The structures and thermal behaviors of PK prepared by homogenous and the supported catalyst were investigated. • The microstructures of PK were changed in the supported catalyst system. • The alternating PK copolymer (PANI-PdCl{sub 2} catalyst) was more thermally stable than PK (PdCl{sub 2} catalyst). • The degradation activation energy values were estimated by Flynn–Wall–Ozawa method and Kissinger method. - Abstract: Copolymerization of styrene with carbon monoxide to give polyketones (PK) was carried out under homogeneous palladium catalyst and polyaniline (PANI) supported palladium(II) catalyst, respectively. The copolymers were characterized by {sup 1}H NMR, {sup 13}C NMR and GPC. The results indicated that the PK catalyzed by the supported catalyst has narrow molecular weight distribution (PDI = 1.18). For comparison purpose of thermal behaviors of PK prepared by the homogeneous and the supported catalyst, thermogravimetric (TG) analysis and derivative thermogravimetric (DTG) were conducted at different heating rates. The peak temperatures (396–402 °C) for PK prepared by the supported catalyst are higher than those (387–395 °C) of PK prepared by the homogeneous catalyst. The degradation activation energy (E{sub k}) values were estimated by Flynn–Wall–Ozawa method and Kissinger method, respectively. The E{sub k} values, as determined by two methods, were found to be in the range 270.72 ± 0.03–297.55 ± 0.10 kJ mol{sup −1}. Structures analysis and thermal degradation analysis revealed that the supported catalyst changed the microstructures of PK, resulting in improving thermal stability of PK.

Dissolved oxygen removal in a column packed with catalyst

International Nuclear Information System (INIS)

Lee, Han Soo; Chung, Hong Suk; Cho, Young Hyun; Ahn, Do Hee; Kim, Eun Kee

1996-01-01

The dissolved oxygen removed by H 2 -O 2 reaction in column packed with various catalysts was examined. The catalysts employed were the prepared polymeric catalyst, platinum on activated carbon, and Lewatit OC-1045 which is available commercially. The column experiments with the prepared polymeric catalyst showed the dissolved oxygen reduced to 35 ppb which is below the limit in feel water of power plants. This implies the likely application of the prepared catalyst for practical use. The activated carbon required the pre-treatment for the removed of dissolved oxygen, since the surface of activated carbon contains much oxygen adsorbed initially. The Lewatit catalyst exposed the best performance, however, the aged one showed the gradual loss of catalytic activity due to degradation of resin catalyst. 14 refs., 6 figs., 2 tabs. (author)

Kinetic Evaluation of Lipid Oils Conversion to Biofuel Using Layered Double Hydroxide Doped with Triazabicyclodece Catalyst

Science.gov (United States)

Nato Lopez, Frank D.

Worldwide, there is an ever increasing need for sustainable, renewable fuels that will accommodate the rapidly increasing energy demand and provide independence from fossil fuels. The search for a sustainable alternative to petroleum based fuels has been a great challenge to the scientific community; therefore, great efforts are being made to overcome the fossil fuels dependence by exploring the prominent field of biofuels (bioethanol and biodiesel). Traditional biodiesel is produced from feedstocks such as vegetable oils and animal fats by converting the triglycerides with methanol in the presence of a homogeneous catalyst to produce fatty acid methyl esters (FAMEs). However, drawbacks of this process are the undesired glycerol byproduct and post reaction processing, including separation from reaction mixture, that results in high costs factors. In the present work, the reaction kinetics of a glycerol-free biodiesel method is studied. This method consists of the transesterification of a vegetable oil (i.e. canola oil) using dimethyl carbonate (DMC) as an alternative methylating agent in presence of layered double hydroxides doped with triazabicyclodecene catalyst (a basic organocatalyst). Furthermore, is theorized that this heterogeneous catalyst (TBD/LDH) simultaneously converts both FFAs and triglycerides due to acid sites formed by Al3+ active sites of the LDH structure. Additionally, the versatility of the Raman in situ technique was used as quantitative analysis tool to monitor the reaction kinetics and collect real time data.

Porous nitrogen-enriched carbonaceous material from marine waste: chitosan-derived layered CNX catalyst for aerial oxidation of 5-hydroxymethylfurfural (HMF) to 2,5-furandicarboxylic acid

Data.gov (United States)

U.S. Environmental Protection Agency — Chitosan-derived, porous and layered nitrogen-enriched carbonaceous CNx catalyst (PLCNx) has been synthesized from marine waste and its use demonstrated in a...

Productions of palm oil bio diesel whit heterogeneous basic catalysts compared to conventional homogeneous catalysts

International Nuclear Information System (INIS)

Rios, Luis A; Franco C, Alexander; Zuleta S, Ernesto

2009-01-01

The conventional process to produce biodiesel involves the presence of homogeneous basic catalysts. However, these catalysts have disadvantages associated to the need of purification steps, which increase the cost of the final product and generate pollution problems caused by the effluents. This paper compares different homogeneous and heterogeneous catalysts for the biodiesel production from palm oil. For this, heterogeneous catalysts supported on alumina were prepared and characterized by nitrogen adsorption, scanning electron microscopy, energy dispersive X ray spectroscopy and X ray diffraction. Transesterification of palm oil with methanol was accomplished at 60 celsius degrade and one hour, varying methanol/oil ratio, the type of catalyst and its concentration. Yields of the reaction and purity of the so obtained biodiesel were evaluated. Comparing the catalysts performance, based on the amount, was found that sodium methoxide (CH 3 ONa) and potassium carbonate supported on alumina (K 2 CO 3 /Al 2 O 3 ) were the catalysts that give the higher purity of biodiesel (96.8 and 95.85% respectively). When was determined the active site quality, by dividing the performance by each mole of active sites, it was found that calcined Na 2 SO 4 /Al 2 O 3 has the most active sites.

A low-crystalline ruthenium nano-layer supported on praseodymium oxide as an active catalyst for ammonia synthesis.

Science.gov (United States)

Sato, Katsutoshi; Imamura, Kazuya; Kawano, Yukiko; Miyahara, Shin-Ichiro; Yamamoto, Tomokazu; Matsumura, Syo; Nagaoka, Katsutoshi

2017-01-01

Ammonia is a crucial chemical feedstock for fertilizer production and is a potential energy carrier. However, the current method of synthesizing ammonia, the Haber-Bosch process, consumes a great deal of energy. To reduce energy consumption, a process and a substance that can catalyze ammonia synthesis under mild conditions (low temperature and low pressure) are strongly needed. Here we show that Ru/Pr 2 O 3 without any dopant catalyzes ammonia synthesis under mild conditions at 1.8 times the rates reported with other highly active catalysts. Scanning transmission electron micrograph observations and energy dispersive X-ray analyses revealed the formation of low-crystalline nano-layers of ruthenium on the surface of Pr 2 O 3 . Furthermore, CO 2 temperature-programmed desorption revealed that the catalyst was strongly basic. These unique structural and electronic characteristics are considered to synergistically accelerate the rate-determining step of NH 3 synthesis, cleavage of the N 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 1111111111111111111111111111111111 1111111111111111111111111111111111 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 1111111111111111111111111111111111 1111111111111111111111111111111111 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 1111111111111111111111111111111111 1111111111111111111111111111111111 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000

Use characterisation of a diatomite catalyst impregnated with iron in the heterogeneous catalytic ozonization process

International Nuclear Information System (INIS)

Garcia Herrera, Walter

2014-01-01

Advanced oxidation processes have had a promising option in the treatment of wastewater, mainly in the presence of emerging and persistent pollutants. Among these processes have highlighted the catalytic ozonization, which has showed positive results in water treatment. Heterogeneous catalytic ozonization was characterized using diatomite impregnated with iron at the Universidad de Costa Rica. Contaminant degradation model was quantified (spectrophotometrically) for ozonization process and catalytic ozonization with the catalyst studied (1.000 g / L) at three different pH 4, 7 and 10. The effect of the catalyst concentration in the solution (0.250, 0.500, 1000, 1500 and 2.000 g/L) was determined under the conditions of pH with better performance of the catalyst. Runs in the presence of tert-butyl alcohol (TBA), known hydroxyl radical scavenger were performed to evaluate the effect on ozone indirect reactions. The degree of mineralization obtained was measured in the catalytic process.The variation of the COD of the solution was quantified under the best working conditions obtained. Finally, the performance of the catalyst in 4 cycles of reuse was studied by monitoring the leached iron of the catalyst, which has turned out to be 12%. Most degradation of contaminant model in ozonization process was obtained at pH 10, in accordance with the above theory (Buhler, Stachelin, & Hoigne, 1984). In contrast, at pH 4 the catalyst has presented the best efficiency, to the 3 minutes the noncatalytic process was curettaged 35% of dye, while the catalytic process by 60% in the same time. The degradation of the contaminant was improved even in the case of noncatalytic process at pH 10, which the 3 minutes was degradated to 44%. The presence of the catalyst at initial pH of 7 and 10, has showed without significant improvements in the process. The solution concentration of catalyst has presented the best efficiency of degradation has been 2,000 g/L, which has increased 70% to 3

Application of a Novel Semiconductor Catalyst, CT, in Degradation of Aromatic Pollutants in Wastewater: Phenol and Catechol

Directory of Open Access Journals (Sweden)

Xiao Chen

2014-01-01

Full Text Available Water-soluble phenol and phenolic compounds were generally removed via advanced oxidation processes. A novel semiconductor catalyst, CT, was the first-time employed in the present study to degrade phenol and catechol. The phenolic compounds (initial concentration of 88 mg L−1 were completely mineralized by the CT catalytic nanoparticles (1% within 15 days, under acidic condition and with the presence of mild UV radiation (15 w, the emitted wavelength is 254 nm and the light intensity <26 μw/cm2. Under the same reaction condition, 1% TiO2 (mixture of rutile and anatase, nanopowder, <100 nm and H2O2 had lower removal efficiency (phenol: <42%; catechol: <60%, whereas the control (without addition of catalysts/H2O2 only showed <12% removal. The processes of phenol/catechol removal by CT followed pseudo-zero-order kinetics. The aromatic structures absorbed the UV energy and passed to an excited state, which the CT worked on. The pollutants were adsorbed on the CT’s surface and oxidized via charge-transfer and hydroxyl radical generation by CT. Given low initial concentrations, a circumstance encountered in wastewater polishing, the current set-up should be an efficient and less energy- and chemical-consumptive treatment method.

A novel structure of scalable air-cathode without Nafion and Pt by rolling activated carbon and PTFE as catalyst layer in microbial fuel cells.

Science.gov (United States)

Dong, Heng; Yu, Hongbing; Wang, Xin; Zhou, Qixing; Feng, Junli

2012-11-01

Single chambered air-cathode microbial fuel cells (MFCs) are promising to be scaled up as sustainable wastewater treatment systems. However, the current air-cathode made by brushing noble metal catalyst and Nafion binder onto carbon matrix becomes one of the biggest bottlenecks for the further development of MFCs due to its high cost, huge labor-consuming and less accuracy. A novel structure of air-cathode was constructed here by rolling activated carbon (AC) and polytetrafluoroethylene (PTFE) as catalyst layer to enhance the reproducibility and improve the performance by an optimized three-phase interface (TPI). Air-cathodes with AC/PTFE ratios of 3, 5, 6, 8 and 11 in the catalyst layer were prepared, and the physical and electrochemical techniques were employed to investigate their surface microstructure and electrochemical characteristics. Uniform cross-linked ropiness networks were observed from the catalyst layer of all the cathodes and increased as the AC/PTFE ratio decreased, while the exchange currents were positively related to this ratio. Maximum power densities (MPDs) decreased as follows: AC/PTFE = 6 (802 mW m(-2) at 3.4 A m(-2)), 5 (704 mW m(-2) at 2.2 mA m(-2)), 8 (647 mW m(-2) at 2.2 A m(-2)), 3 (597 mW m(-2) at 2.1 A m(-2)) and 11 (584 mW m(-2) at 2.0 mA m(-2)), which was due to the changes of both the capacitance characteristics and conductivities according to the electrochemical impedance spectrum (EIS) analysis. This study demonstrated that inexpensive, highly reproducible, high performance and scalable air-cathode can be produced by rolling method without using noble metal and expensive binder. Copyright © 2012 Elsevier Ltd. All rights reserved.

Ultrasound assisted synthesis of iron doped TiO2 catalyst.

Science.gov (United States)

Ambati, Rohini; Gogate, Parag R

2018-01-01

The present work deals with synthesis of Fe (III) doped TiO 2 catalyst using the ultrasound assisted approach and conventional sol-gel approach with an objective of establishing the process intensification benefits. Effect of operating parameters such as Fe doping, type of solvent, solvent to precursor ratio and initial temperature has been investigated to get the best catalyst with minimum particle size. Comparison of the catalysts obtained using the conventional and ultrasound assisted approach under the optimized conditions has been performed using the characterization techniques like DLS, XRD, BET, SEM, EDS, TEM, FTIR and UV-Vis band gap analysis. It was established that catalyst synthesized by ultrasound assisted approach under optimized conditions of 0.4mol% doping, irradiation time of 60min, propan-2-ol as the solvent with the solvent to precursor ratio as 10 and initial temperature of 30°C was the best one with minimum particle size as 99nm and surface area as 49.41m 2 /g. SEM analysis, XRD analysis as well as the TEM analysis also confirmed the superiority of the catalyst obtained using ultrasound assisted approach as compared to the conventional approach. EDS analysis also confirmed the presence of 4.05mol% of Fe element in the sample of 0.4mol% iron doped TiO 2 . UV-Vis band gap results showed the reduction in band gap from 3.2eV to 2.9eV. Photocatalytic experiments performed to check the activity also confirmed that ultrasonically synthesized Fe doped TiO 2 catalyst resulted in a higher degradation of Acid Blue 80 as 38% while the conventionally synthesized catalyst resulted in a degradation of 31.1%. Overall, the work has clearly established importance of ultrasound in giving better catalyst characteristics as well as activity for degradation of the Acid Blue 80 dye. Copyright © 2017 Elsevier B.V. All rights reserved.

Interaction between Nafion ionomer and noble metal catalyst for PEMFCs

DEFF Research Database (Denmark)

Andersen, Shuang Ma

The implement of polymer impregnation in electrode structure (catalyst layer) decreasing the noble metal catalyst loading by a factor of ten , , is one of the essential mile stones in the evolution of Proton Exchange Membrane Fuel Cells’ development among the application of catalyst support and e...

Rapid establishment of phenol- and quinoline-degrading consortia driven by the scoured cake layer in an anaerobic baffled ceramic membrane bioreactor.

Science.gov (United States)

Wang, Wei; Wang, Shun; Ren, Xuesong; Hu, Zhenhu; Yuan, Shoujun

2017-11-01

Although toxic and refractory organics, such as phenol and quinoline, are decomposed by anaerobic bacteria, the establishment of specific degrading consortia is a relatively slow process. An anaerobic membrane bioreactor allows for complete biomass retention that can aid the establishment of phenol- and quinoline-degrading consortia. In this study, the anaerobic digestion of phenol (500 mg L -1 ) and quinoline (50 mg L -1 ) was investigated using an anaerobic baffled ceramic membrane bioreactor (ABCMBR). The results showed that, within 30 days, 99% of phenol, 98% of quinoline and 88% of chemical oxygen demand (COD) were removed. The substrate utilisation rates of the cake layer for phenol and quinoline, and specific methanogenic activity of the cake layer, were 7.58 mg phenol g -1  mixed liquor volatile suspended solids (MLVSS) day -1 , 8.23 mg quinoline g -1  MLVSS day -1 and 0.55 g COD CH4  g -1  MLVSS day -1 , respectively. The contribution of the cake layer to the removals of phenol and quinoline was extremely underestimated because the uncounted scoured cake layer was disregarded. Syntrophus was the key population for phenol and quinoline degradation, and it was more abundant in the cake layer than in the bulk sludge. The highly active scattered cake layer sped up the establishment of phenol- and quinoline-degrading consortia in the ABCMBR.

Synthesis of hierarchically porous perovskite-carbon aerogel composite catalysts for the rapid degradation of fuchsin basic under microwave irradiation and an insight into probable catalytic mechanism

Science.gov (United States)

Wang, Yin; Wang, Jiayuan; Du, Baobao; Wang, Yun; Xiong, Yang; Yang, Yiqiong; Zhang, Xiaodong

2018-05-01

3D hierarchically porous perovskites LaFe0.5M0.5O3-CA (M = Mn, Cu) were synthesized by a two-step method using PMMA as template and supporting with carbon aerogel, which were characterized with SEM, TEM, XRD, XPS and FT-IR spectroscopy. The as-prepared composites were used in microwave (MW) catalytic degradation of fuchsin basic (FB) dye wastewater. Batch experiment results showed that the catalytic degradation of FB could be remarkably improved by coating with CA. And LaFe0.5Cu0.5O3-CA exhibited higher catalytic performance than LaFe0.5Mn0.5O3-CA, which had a close connection with the activity of substitution metal ion in B site of the catalysts. The FB removal fit pseudo-first-order model and the degradation rate constant increased with initial pH value and MW powder while decreases with initial FB concentration. All catalysts presented favorable recycling and stability in the repeated experiment. Radical scavenger measurements indicated that hydroxyl radicals rather than surface peroxide and hole played an important role in the catalytic process, and its quantity determined the degradation of FB. Furthermore, both Cu and Fe species were involved in the formation of active species, which were responsible to the excellent performance of the LaFe0.5Cu0.5O3-CA/MW system. Therefore, LaFe0.5Cu0.5O3-CA/MW showed to be a promising technology for the removal of organic pollutants in wastewater treatment applications.

Nanoscale Protection Layers To Mitigate Degradation in High-Energy Electrochemical Energy Storage Systems.

Science.gov (United States)

Lin, Chuan-Fu; Qi, Yue; Gregorczyk, Keith; Lee, Sang Bok; Rubloff, Gary W

2018-01-16

In the pursuit of energy storage devices with higher energy and power, new ion storage materials and high-voltage battery chemistries are of paramount importance. However, they invite-and often enhance-degradation mechanisms, which are reflected in capacity loss with charge/discharge cycling and sometimes in safety problems. Degradation mechanisms are often driven by fundamentals such as chemical and electrochemical reactions at electrode-electrolyte interfaces, volume expansion and stress associated with ion insertion and extraction, and profound inhomogeneity of electrochemical behavior. While it is important to identify and understand these mechanisms at some reasonable level, it is even more critical to design strategies to mitigate these degradation pathways and to develop means to implement and validate the strategies. A growing set of research highlights the mitigation benefits achievable by forming thin protection layers (PLs) intentionally created as artificial interphase regions at the electrode-electrolyte interface. These advances illustrate a promising-perhaps even generic-pathway for enabling higher-energy and higher-voltage battery configurations. In this Account, we summarize examples of such PLs that serve as mitigation strategies to avoid degradation in lithium metal anodes, conversion-type electrode materials, and alloy-type electrodes. Examples are chosen from a larger body of electrochemical degradation research carried out in Nanostructures for Electrical Energy Storage (NEES), our DOE Energy Frontier Research Center. Overall, we argue on the basis of experimental and theoretical evidence that PLs effectively stabilize the electrochemical interfaces to prevent parasitic chemical and electrochemical reactions and mitigate the structural, mechanical, and compositional degradation of the electrode materials at the electrode-electrolyte interfaces. The evidenced improvement in performance metrics is accomplished by (1) establishing a homogeneous

Synthesis of efficient silica supported TiO_2/Ag_2O heterostructured catalyst with enhanced photocatalytic performance

International Nuclear Information System (INIS)

Zelekew, Osman Ahmed; Kuo, Dong-Hau; Yassin, Jemal Mohammed; Ahmed, Kedir Ebrahim; Abdullah, Hairus

2017-01-01

Graphical abstract: Proposed charge separation mechanism and degradation of dye with photocatalyst under light irradiation. - Highlights: • n-type TiO_2 inside and p-type Ag_2O outside was designed. • The p–n junction formation built in an electric field. • The p–n junction facilitates the electrons and holes separation. • The degradation of dye becomes more effective with Ag_2O/TiO_2 catalyst. - Abstract: We develop the n-type TiO_2 coated on SiO_2 support abbreviated as SiO_2/TiO_2 (ST) followed by deposition of p-type Ag_2O nanoparticles outside for the purpose of photocatalytic degradation of organic pollutants. Different composite catalysts were prepared with changing the amount AgNO_3 (such as 0%, 5%, 10%, 20%, and 30%) and the composites were abbreviated as ST, STA-5, STA-10, STA-20, and STA-30, respectively. The composite catalysts were characterized with different techniques and tested for Rhodamine B (RhB) dye degradation under UV and visible light. Among the composite catalysts, the degradation efficiency of STA-20 was the highest and it degraded about 99% within 40 min under UV light-irradiation. However, the ST, STA-5, STA-10, and STA-30 composite catalysts could degrade about 21%, 47%, 58%, and 75% of the dye, respectively. Furthermore, the STA-5, STA-10, STA-20, and STA-30 composites were also tested and about 39%, 47%, 57%, and 42% of the dye, respectively, was degraded under visible light source. Hence, the formation of p–n junction heterostructure between n-type TiO_2 and p-type Ag_2O could enhance the degradation of RhB in both UV and visible light irradiation. It could be also potentially applicable photocatalyst for environmental remediation.

NATURAL IRON OXIDE AS A HETEROGENEOUS PHOTO-FENTON-LIKE CATALYST FOR THE DEGRADATION OF 1-NAPHTHOL UNDER ARTIFICIAL AND SOLAR LIGHT

Directory of Open Access Journals (Sweden)

L MAMMERI

2014-07-01

Full Text Available A heterogeneous photo-Fenton-like degradation process of 1-naphthol (1-NP promoted by natural iron oxide (NIO in the presence of H2O2 was studied under artificial (365 nm and solar irradiation. This is an important reaction for the environment since both H2O2 and iron oxides are common constituents of natural waters. Furthermore, iron oxides function as catalysts in chemical oxidation processes used with H2O2 for treatment of contaminated waters. The NIO used in this study was characterized by X-ray diffraction (XRD, X-ray fluorescence and Brunauer–Emmett–Teller (BET methods. The results show that the NIO is a composite material that contains predominantly crystalline hematite particales (Fe2O3. The Fe2O3 in NIO was able to initiate the Fenton-like and photo-Fenton-like reactions. The effects of initial pH, catalyst dosage, H2O2 concentration and the wavelength of the light source (UV and solar on the photodegradation of 1-NP were investigated. The optimal content of the NIO was 1 g L-1 and the optimal H2O2 concentration was 10 mM. The degradation could occur efficiently over a wide pH range of 3-8.3. Furthermore, an important effect of light was observed. The photo-oxidation of 1-NP in NIO-H2O2 system under solar light was significantly accelerated in comparison with artificial irradiation at 365 nm.

Final Project Report: Development of Micro-Structural Mitigation Strategies for PEM Fuel Cells: Morphological Simulations and Experimental Approaches

Energy Technology Data Exchange (ETDEWEB)

Wessel, Silvia [Ballard Materials Products; Harvey, David [Ballard Materials Products

2013-06-28

The durability of PEM fuel cells is a primary requirement for large scale commercialization of these power systems in transportation and stationary market applications that target operational lifetimes of 5,000 hours and 40,000 hours by 2015, respectively. Key degradation modes contributing to fuel cell lifetime limitations have been largely associated with the platinum-based cathode catalyst layer. Furthermore, as fuel cells are driven to low cost materials and lower catalyst loadings in order to meet the cost targets for commercialization, the catalyst durability has become even more important. While over the past few years significant progress has been made in identifying the underlying causes of fuel cell degradation and key parameters that greatly influence the degradation rates, many gaps with respect to knowledge of the driving mechanisms still exist; in particular, the acceleration of the mechanisms due to different structural compositions and under different fuel cell conditions remains an area not well understood. The focus of this project was to address catalyst durability by using a dual path approach that coupled an extensive range of experimental analysis and testing with a multi-scale modeling approach. With this, the major technical areas/issues of catalyst and catalyst layer performance and durability that were addressed are: 1. Catalyst and catalyst layer degradation mechanisms (Pt dissolution, agglomeration, Pt loss, e.g. Pt in the membrane, carbon oxidation and/or corrosion). a. Driving force for the different degradation mechanisms. b. Relationships between MEA performance, catalyst and catalyst layer degradation and operational conditions, catalyst layer composition, and structure. 2. Materials properties a. Changes in catalyst, catalyst layer, and MEA materials properties due to degradation. 3. Catalyst performance a. Relationships between catalyst structural changes and performance. b. Stability of the three-phase boundary and its effect on

Performance of a polymer electrolyte membrane fuel cell with thin film catalyst electrodes

Energy Technology Data Exchange (ETDEWEB)

Chun, Young Gab; Kim, Chang Soo; Peck, Dong Hyun; Shin, Dong Ryul [Korea Institute of Energy Research, Taejon (Korea, Republic of)

1998-03-15

In order to develop a kW-class polymer electrolyte membrane fuel cell (PEMFC), several electrodes have been fabricated by different catalyst layer preparation procedures and evaluated based on the cell performance. Conventional carbon paper and carbon cloth electrodes were fabricated using a ptfe-bonded Pt/C electrol catalyst by coating and rolling methods. Thin-film catalyst/ionomer composite layers were also formed on the membrane by direct coating and transfer printing techniques. The performance evaluation with catalyst layer preparation methods was carried out using a large or small electrode single cell. Conventional and thin film membrane and electrode assemblies (MEAs) with small electrode area showed a performance of 350 and 650 mA/cm{sup 2} at 0.6 V, respectively. The performance of direct coated thin film catalyst layer with 300 cm{sup 2} MEAs was higher than those of the conventional and transfer printing technique MEAs. The influence of some characteristic parameters of the thin film electrode on electrochemical performance was examined. Various other aspects of overall operation of PEMFC stacks were also discussed. (orig.)

Observation of ionomer in catalyst ink of polymer electrolyte fuel cell using cryogenic transmission electron microscopy

International Nuclear Information System (INIS)

Takahashi, Shinichi; Shimanuki, Junichi; Mashio, Tetsuya; Ohma, Atsushi; Tohma, Hajime; Ishihara, Ayumi; Ito, Yoshiko; Nishino, Yuri; Miyazawa, Atsuo

2017-01-01

Optimizing the catalyst layer structure is one of the key issues for improving performance despite lower platinum loading. The catalyst ink, consisting of platinum-loaded carbon particles and ionomer dispersed in an aqueous solvent, is a key factor for controlling the structure of the catalyst layer because the catalyst layer is prepared in a wet coating process. For that purpose, we visualized the nanostructure of the ionomer in the catalyst ink by cryogenic electron microscopy, especially cryogenic transmission electron microscopy (cryo-TEM). By cryo-TEM, it was revealed that ionomer molecules formed rod-like aggregates macro-homogeneously in the solvent, and a similar morphology was observed in a carbon-particle-containing solvent. In contrast, ionomer aggregates in the catalyst ink containing platinum nanoparticles loaded on carbon particles were denser in the vicinity of the platinum-loaded carbon particles. That can be attributed to strong interaction between platinum nanoparticles and sulfonic acid groups in the ionomer. It also implies that a good understanding of ionomer morphology in the catalyst ink can play an important role in controlling the catalyst layer microstructure for reducing platinum loading.

Using ammonium bicarbonate as pore former in activated carbon catalyst layer to enhance performance of air cathode microbial fuel cell

Science.gov (United States)

Li, Da; Qu, Youpeng; Liu, Jia; He, Weihua; Wang, Haiman; Feng, Yujie

2014-12-01

The rolling catalyst layers in air cathode microbial fuel cells (MFCs) are prepared by introducing NH4HCO3 as pore former (PF) with four PF/activated carbon mass ratios of 0.1, 0.2, 0.3 and 1.0. The maximum power density of 892 ± 8 mW m-2 is obtained by cathodes with the mass ratio of 0.2, which is 33% higher than that of the control reactor (without PF, 671 ± 22 mW m-2). Pore analysis indicates the porosity increases by 38% and the major pore range concentrates between 0.5 μm-0.8 μm which likely facilitates to enrich the active reaction sites compared to 0.8 μm-3.0 μm in the control and other PF-cathodes. In addition, pore structure endows the cathode improved exchange current density by 2.4 times and decreased charge transfer resistance by 44%, which are the essential reasons to enhance the oxygen reduction. These results show that addition of NH4HCO3 proves an effective way to change the porosity and pore distribution of catalyst layers and then enhance the MFC performance.

Butanol Dehydration over V₂O₅-TiO₂/MCM-41 Catalysts Prepared via Liquid Phase Atomic Layer Deposition.

Science.gov (United States)

Choi, Hyeonhee; Bae, Jung-Hyun; Kim, Do Heui; Park, Young-Kwon; Jeon, Jong-Ki

2013-04-29

MCM-41 was used as a support and, by using atomic layer deposition (ALD) in the liquid phase, a catalyst was prepared by consecutively loading titanium oxide and vanadium oxide to the support. This research analyzes the effect of the loading amount of vanadium oxide on the acidic characteristics and catalytic performance in the dehydration of butanol. The physical and chemical characteristics of the TiO₂-V₂O₅/MCM-41 catalysts were analyzed using XRF, BET, NH₃-TPD, XRD, Py-IR, and XPS. The dehydration reaction of butanol was performed in a fixed bed reactor. For the samples with vanadium oxide loaded to TiO₂/MCM-41 sample using the liquid phase ALD method, it was possible to increase the loading amount until the amount of vanadium oxide reached 12.1 wt %. It was confirmed that the structural properties of the mesoporous silica were retained well after titanium oxide and vanadium loading. The NH₃-TPD and Py-IR results indicated that weak acid sites were produced over the TiO₂/MCM-41 samples, which is attributed to the generation of Lewis acid sites. The highest activity of the V₂O₅(12.1)-TiO₂/MCM-41 catalyst in 2-butanol dehydration is ascribed to it having the highest number of Lewis acid sites, as well as the highest vanadium dispersion.

Immobilization of molecular catalysts in supported ionic liquid phases.

Science.gov (United States)

Van Doorslaer, Charlie; Wahlen, Joos; Mertens, Pascal; Binnemans, Koen; De Vos, Dirk

2010-09-28

In a supported ionic liquid phase (SILP) catalyst system, an ionic liquid (IL) film is immobilized on a high-surface area porous solid and a homogeneous catalyst is dissolved in this supported IL layer, thereby combining the attractive features of homogeneous catalysts with the benefits of heterogeneous catalysts. In this review reliable strategies for the immobilization of molecular catalysts in SILPs are surveyed. In the first part, general aspects concerning the application of SILP catalysts are presented, focusing on the type of catalyst, support, ionic liquid and reaction conditions. Secondly, organic reactions in which SILP technology is applied to improve the performance of homogeneous transition-metal catalysts are presented: hydroformylation, metathesis reactions, carbonylation, hydrogenation, hydroamination, coupling reactions and asymmetric reactions.

Solution-deposited F:SnO₂/TiO₂ as a base-stable protective layer and antireflective coating for microtextured buried-junction H₂-evolving Si photocathodes.

Science.gov (United States)

Kast, Matthew G; Enman, Lisa J; Gurnon, Nicholas J; Nadarajah, Athavan; Boettcher, Shannon W

2014-12-24

Protecting Si photocathodes from corrosion is important for developing tandem water-splitting devices operating in basic media. We show that textured commercial Si-pn(+) photovoltaics protected by solution-processed semiconducting/conducting oxides (plausibly suitable for scalable manufacturing) and coupled to thin layers of Ir yield high-performance H2-evolving photocathodes in base. They also serve as excellent test structures to understand corrosion mechanisms and optimize interfacial electrical contacts between various functional layers. Solution-deposited TiO2 protects Si-pn(+) junctions from corrosion for ∼24 h in base, whereas junctions protected by F:SnO2 fail after only 1 h of electrochemical cycling. Interface layers consisting of Ti metal and/or the highly doped F:SnO2 between the Si and TiO2 reduce Si-emitter/oxide/catalyst contact resistance and thus increase fill factor and efficiency. Controlling the oxide thickness led to record photocurrents near 35 mA cm(-2) at 0 V vs RHE and photocathode efficiencies up to 10.9% in the best cells. Degradation, however, was not completely suppressed. We demonstrate that performance degrades by two mechanisms, (1) deposition of impurities onto the thin catalyst layers, even from high-purity base, and (2) catastrophic failure via pinholes in the oxide layers after several days of operation. These results provide insight into the design of hydrogen-evolving photoelectrodes in basic conditions, and highlight challenges.

Novel synthesis of highly durable and active Pt catalyst encapsulated in nitrogen containing carbon for polymer electrolyte membrane fuel cell

Science.gov (United States)

Lee, Hyunjoon; Sung, Yung-Eun; Choi, Insoo; Lim, Taeho; Kwon, Oh Joong

2017-09-01

Novel synthesis of a Pt catalyst encapsulated in a N-containing carbon layer for use in a polymer electrolyte membrane fuel cell is described in this study. A Pt-aniline complex, formed by mixing Pt precursor and aniline monomer, was used as the source of Pt, C, and N. Heat treatment of the Pt-aniline complex with carbon black yielded 5 nm Pt nanoparticles encapsulated by a N-containing carbon layer originating from aniline carbonization. The synthesized Pt catalyst exhibited higher mass specific activity to oxygen reduction reaction than that shown by conventional Pt/C catalyst because pyridinic N with graphitic carbon in the carbon layer provided active sites for oxygen reduction reaction in addition to those provided by Pt. In single cell testing, initial performance of the synthesized catalyst was limited because the thick catalyst layer increased resistance related to mass transfer. However, it was observed that the carbon layer successfully prevented Pt nanoparticles from growing via agglomeration and Ostwald ripening under fuel cell operation, thereby improving durability. Furthermore, a mass specific performance of the synthesized catalyst higher than that of a conventional Pt/C catalyst was achieved by modifying the synthesized catalyst's layer thickness.

Simulation of the Dynamics of Isothermal Growth of Single-Layer Graphene on a Copper Catalyst in the Process of Chemical Vapor Deposition of Hydrocarbons

Science.gov (United States)

Futko, S. I.; Shulitskii, B. G.; Labunov, V. A.; Ermolaeva, E. M.

2018-01-01

A new kinetic model of isothermal growth of single-layer graphene on a copper catalyst as a result of the chemical vapor deposition of hydrocarbons on it at a low pressure has been developed on the basis of in situ measurements of the growth of graphene in the process of its synthesis. This model defines the synthesis of graphene with regard for the chemisorption and catalytic decomposition of ethylene on the surface of a copper catalyst, the diffusion of carbon atoms in the radial direction to the nucleation centers within the thin melted near-surface copper layer, and the nucleation and autocatalytic growth of graphene domains. It is shown that the time dependence of the rate of growth of a graphene domain has a characteristic asymmetrical bell-like shape. The dependences of the surface area and size of a graphene domain and the rate of its growth on the time at different synthesis temperatures and ethylene concentrations have been obtained. Time characteristics of the growth of graphene domains depending on the parameters of their synthesis were calculated. The results obtained can be used for determining optimum regimes of synthesis of graphene in the process of chemical vapor deposition of hydrocarbons on different catalysts with a low solubility of carbon.

Sulfidization of an aluminocobaltomolybdenum catalyst using the 35S radioisotope

International Nuclear Information System (INIS)

Isagulyants, G.V.; Greish, A.A.; Kogan, V.M.

1987-01-01

It has been established that in aluminocobaltomolybdenum catalyst sulfidized with elemental sulfur there are two types of sulfur, free and bound. The maximum amount of bound sulfur in ACM catalyst is 6.6 wt. %, which corresponds to practically complete sulfidation of the ACM catalyst. In the presence of hydrogen an equilibrium distribution of bound sulfur is achieved in a granule of ACM catalyst irrespective of the temperature of sulfidation. In a nitrogen atmosphere it is primarily the surface layers of the catalyst that are sulfured

XPS and STEM study of the interface formation between ultra-thin Ru and Ir OER catalyst layers and perylene red support whiskers

Directory of Open Access Journals (Sweden)

Atanasoska Ljiljana L.

2013-01-01

Full Text Available The interface formation between nano-structured perylene red (PR whiskers and oxygen evolution reaction (OER catalysts ruthenium and iridium has been studied systematically by XPS and STEM. The OER catalyst over-layers with thicknesses ranging from ~0.1 to ~50 nm were vapor deposited onto PR ex-situ. STEM images demonstrate that, with increasing thickness, Ru and Ir transform from amorphous clusters to crystalline nanoparticles, which agglomerate with increased over-layer thickness. XPS data show a strong interaction between Ru and PR. Ir also interacts with PR although not to the extent seen for Ru. At low coverages, the entire Ru deposit is in the reacted state while a small portion of the deposited Ir remains metallic. Ru and Ir bonding occur at the PR carbonyl sites as evidenced by the attenuation of carbonyl photoemission and the emergence of new peak assigned to C-O single bond. The curve fitting analysis and the derived stoichiometry indicates the formation of metallo-organic bonds. The co-existence of oxide bonds is also apparent.

Iron Contamination Mechanism and Reaction Performance Research on FCC Catalyst

Directory of Open Access Journals (Sweden)

Zhaoyong Liu

2015-01-01

Full Text Available FCC (Fluid Catalytic Cracking catalyst iron poisoning would not only influence units’ product slate; when the poisoning is serious, it could also jeopardize FCC catalysts’ fluidization in reaction-regeneration system and further cause bad influences on units’ stable operation. Under catalytic cracking reaction conditions, large amount of iron nanonodules is formed on the seriously iron contaminated catalyst due to exothermic reaction. These nodules intensify the attrition between catalyst particles and generate plenty of fines which severely influence units’ smooth running. A dense layer could be formed on the catalysts’ surface after iron contamination and the dense layer stops reactants to diffuse to inner structures of catalyst. This causes extremely negative effects on catalyst’s heavy oil conversion ability and could greatly cut down gasoline yield while increasing yields of dry gas, coke, and slurry largely. Research shows that catalyst’s reaction performance would be severely deteriorated when iron content in E-cat (equilibrium catalyst exceeds 8000 μg/g.

Decolorization of methylene blue in layered manganese oxide suspension with H2O2

International Nuclear Information System (INIS)

Zhang Lili; Nie Yulun; Hu Chun; Hu Xuexiang

2011-01-01

Highlights: → Layered birnessite-type manganese oxides exhibited a well-crystallized octahedral layer (OL) structure with β-MnOOH, α-MnOOH and γ-Mn 3 O 4 . → The catalyst was highly effective for the decolorization and degradation of methylene blue in the presence of H 2 O 2 at neutral pH. → The 1 O 2 and O 2 · - were the main reactive oxygen species in the reaction. - Abstract: Layered birnessite-type manganese oxides (Na-OL-1) were prepared via a redox reaction involving MnO 4 - and Mn 2+ under markedly alkaline conditions. According to the XRD analysis, the resulting material exhibited a well-crystallized octahedral layer (OL) structure with several different phases, including β-MnOOH, α-MnOOH and γ-Mn 3 O 4 . The catalyst was highly effective for the decolorization and degradation of methylene blue (MB) in the presence of H 2 O 2 at neutral pH. The tested MB was completely decolorized in Na-OL-1 suspension by the fraction dosing of H 2 O 2 (556.5 mM at the beginning and then 183.8 mM at 40 min). Based on the studies of electron spin resonance and the effect of radical scavengers, the 1 O 2 and O 2 · - were the main reactive oxygen species (ROS) in the reaction. It was found that both oxygen and ROS were generated from the decomposition of H 2 O 2 in Na-OL-1 suspension, wherein the decomposition pathways were proposed. The generation of H 2 O 2 in Na-OL-1 suspension at air atmosphere indicated that the existence of multivalent manganese oxides greatly enhanced the interfacial electron transfer, leading to the high activity of Na-OL-1.

Atomic Layer Deposition on Porous Materials: Problems with Conventional Approaches to Catalyst and Fuel Cell Electrode Preparation

Directory of Open Access Journals (Sweden)

Tzia Ming Onn

2018-03-01

Full Text Available Atomic layer deposition (ALD offers exciting possibilities for controlling the structure and composition of surfaces on the atomic scale in heterogeneous catalysts and solid oxide fuel cell (SOFC electrodes. However, while ALD procedures and equipment are well developed for applications involving flat surfaces, the conditions required for ALD in porous materials with a large surface area need to be very different. The materials (e.g., rare earths and other functional oxides that are of interest for catalytic applications will also be different. For flat surfaces, rapid cycling, enabled by high carrier-gas flow rates, is necessary in order to rapidly grow thicker films. By contrast, ALD films in porous materials rarely need to be more than 1 nm thick. The elimination of diffusion gradients, efficient use of precursors, and ligand removal with less reactive precursors are the major factors that need to be controlled. In this review, criteria will be outlined for the successful use of ALD in porous materials. Examples of opportunities for using ALD to modify heterogeneous catalysts and SOFC electrodes will be given.

Synthesis of Mn-intercalated layered titanate by exfoliation–flocculation approach and its efficient photocatalytic activity under visible–light

International Nuclear Information System (INIS)

Fu, Jie; Tian, Yanlong; Chang, Binbin; Li, Gengnan; Xi, Fengna; Dong, Xiaoping

2012-01-01

A novel Mn-intercalated layered titanate as highly active photocatalyst in visible-light region has been synthesized via a convenient and efficient exfoliation–flocculation approach with divalent Mn ions and monolayer titanate nanosheets. The 0.91 nm interlayer spacing of obtained photocatalyst is in accordance with the sum of the thickness of titanate nanosheet and the diameter of Mn ions. The yellow photocatalyst shows a spectral response in visible-light region and the calculated band gap is 2.59 eV. The photocatalytic performance of this material was evaluated by degradation and mineralization of an aqueous dye methylene blue under visible-light irradiation, and an enhanced photocatalytic activity in comparison with protonated titanate as well as the P25 TiO 2 and N-doped TiO 2 was obtained. Additionally, the layered structure is retained, no dye ions intercalating occurs during the photocatalysis process, and a ∼90% photocatalytic activity can be remained after reusing 3 cycles. - Graphical abstract: Mn-intercalated layered titanate as a novel and efficient visible-light harvesting photocatalyst was synthesized via a convenient and efficient exfoliation–flocculation approach in a mild condition. Highlights: ► Mn-intercalated titanate has been prepared by exfoliation–flocculation approach. ► The as-prepared catalyst shows spectral response in the visible-light region. ► Heat treatment at certain temperature enables formation of Mn-doped TiO 2 . ► Dye can be degradated effectively by the catalyst under visible light irradiation.

Iron doped fibrous-structured silica nanospheres as efficient catalyst for catalytic ozonation of sulfamethazine.

Science.gov (United States)

Bai, Zhiyong; Wang, Jianlong; Yang, Qi

2018-04-01

Sulfonamide antibiotics are ubiquitous pollutants in aquatic environments due to their large production and extensive application. In this paper, the iron doped fibrous-structured silica (KCC-1) nanospheres (Fe-KCC-1) was prepared, characterized, and applied as a catalyst for catalytic ozonation of sulfamethazine (SMT). The effects of ozone dosage, catalyst dosage, and initial concentration of SMT were examined. The experimental results showed that Fe-KCC-1 had large surface area (464.56 m2 g -1 ) and iron particles were well dispersed on the catalyst. The catalyst had high catalytic performance especially for the mineralization of SMT, with mineralization ratio of about 40% in a wide pH range. With addition of Fe-KCC-1, the ozone utilization increased nearly two times than single ozonation. The enhancement of SMT degradation was mainly due to the surface reaction, and the increased mineralization of SMT was due to radical mechanism. Fe-KCC-1 was an efficient catalyst for SMT degradation in catalytic ozonation system.

Porous nitrogen-enriched carbonaceous material from marine waste: chitosan-derived layered CNX catalyst for aerial oxidation of 5-hydroxymethylfurfural (HMF) to 2,5-furandicarboxylic acid

Science.gov (United States)

Chitosan derived porous layered nitrogen-enriched carbonaceous CNx catalyst (PLCNx) has been synthesized from marine waste and its use demonstrated in a metal-free heterogeneous selective oxidation of 5-hydroxymethyl-furfural (HMF) to 2,5-furandicarboxylic acid (FDCA) using aeria...

Mg-Cu-Al layered double hydroxides based catalysts for the reduction of nitrates in aqueous solutions

Directory of Open Access Journals (Sweden)

Vulić Tatjana J.

2010-01-01

Full Text Available The secondary waste and bacterial contamination in physico-chemical and biological separation processes used today for nitrate removal from ground water make novel catalytic technologies that convert nitrates to unharmful gaseous nitrogen, very attractive for scientific research. The Mg-Cu-Al layered double hydroxide (LDH based catalysts with different Mg/Al ratio were investigated in water denitrification reaction in the presence of hydrogen and with solely copper as an active phase. Since LDHs have ion exchange properties and their derived mixed oxides possess memory effect (restoration of layered structure after thermal decomposition, their adsorption capacity for nitrates was also measured in the same model system. All studied samples showed nitrate removal from 23% to 62% following the decrease in Al content, as well as the substantial adsorption capacity ranging from 18% to 38%. These results underlie the necessity to take into account the effects of the adsorption in all future investigations.

Analysis of proton exchange membrane fuel cell catalyst layers for reduction of platinum loading at Nissan

International Nuclear Information System (INIS)

Ohma, Atsushi; Mashio, Tetsuya; Sato, Kazuyuki; Iden, Hiroshi; Ono, Yoshitaka; Sakai, Kei; Akizuki, Ken; Takaichi, Satoshi; Shinohara, Kazuhiko

2011-01-01

The biggest issue that must be addressed in promoting widespread use of fuel cell vehicles (FCVs) is to reduce the cost of the fuel cell system. Especially, it is of vital importance to reduce platinum (Pt) loading of catalyst layers (CLs) in the membrane electrode assembly (MEA) of a proton exchange membrane fuel cell (PEMFC). In order to lower the Pt loading of the MEA, mass transport of reactants related to the performance in high current density should be enhanced significantly as well as kinetics of the catalyst, which can result in the better Pt utilization and effectiveness. In this study, we summarized our analytical approach and methods for reduction of Pt loading in CLs. Microstructure, mass transport properties of the reactants, and their relation in CLs were elucidated by applying experimental analyses and computational methods. A simple CL model for I–V performance prediction was then established, where experimentally elucidated parameters of the microstructure and the properties in CLs were taken into account. Finally, we revealed the impact of lowering the Pt loading on the transport properties, polarization, and the I–V performance.

Direct synthesis of Pt-free catalyst on gas diffusion layer of fuel cell and usage of high boiling point fuels for efficient utilization of waste heat

International Nuclear Information System (INIS)

Nandan, Ravi; Goswami, Gopal Krishna; Nanda, Karuna Kar

2017-01-01

Graphical abstract: Direct-grown boron-doped carbon nanotubes on gas-diffusion layer as efficient Pt-free cathode catalyst for alcohol fuel cells, high boiling point fuels used to obtain hot fuels for the enhancement of cell performance that paves the way for the utilization of waste heat. Display Omitted -- Highlights: •One-step direct synthesis of boron-doped carbon nanotubes (BCNTs) on gas diffusion layer (GDL). •Home built fuel-cell testing using BCNTs on GDL as Pt-free cathode catalyst. •BCNTs exhibit concentration dependent oxygen reduction reaction and the cell performance. •Effective utilization of waste heat to raise the fuel temperature. •Fuel selectivity to raise the fuel temperature and the overall performance of the fuel cells. -- Abstract: Gas diffusion layers (GDL) and electrocatalysts are integral parts of fuel cells. It is, however, a challenging task to grow Pt-free robust electrocatalyst directly on GDL for oxygen reduction reaction (ORR) – a key reaction in fuel cells. Here, we demonstrate that boron-doped carbon nanotubes (BCNTs) grown directly on gas-diffusion layer (which avoid the need of ionomer solution used for catalyst loading) can be used as efficient Pt-free catalyst in alcohol fuel cells. Increase in boron concentration improves the electrochemical ORR activity in terms of onset and ORR peak positions, half-wave potentials and diffusion-limited current density that ensure the optimization of the device performance. The preferential 4e − pathway, excellent cell performance, superior tolerance to fuel crossover and long-term stability makes directly grown BCNTs as an efficient Pt-free cathode catalyst for cost-effective fuel cells. The maximum power density of the fuel cell is found to increase monotonically with boron concentration. In addition to the application of BCNTs in fuel cell, we have introduced the concept of hot fuels so that waste heat can effectively be used and external power sources can be avoided. The fuel

Flame spray deposition of porous catalysts on surfaces and in microsystems

DEFF Research Database (Denmark)

Thybo, Susanne; Jensen, Søren; Johansen, Johnny

2004-01-01

Flame spray synthesis is investigated as a method for one step synthesis and deposition of porous catalysts onto surfaces and into microreactors. Using a standard photolithographic lift-off process, catalyst can be deposited on flat surfaces in patterns with sub-millimeter feature sizes....... With shadow masks, porous catalyst layers can be deposited selectively into microchannels. Using Au/TiO$_2$ as test catalyst and CO-oxidation as test reaction, it is found that the apparent activation energy of the deposited catalyst is similar to what is normally seen for supported gold catalysts...

Synthesis of efficient silica supported TiO{sub 2}/Ag{sub 2}O heterostructured catalyst with enhanced photocatalytic performance

Energy Technology Data Exchange (ETDEWEB)

Zelekew, Osman Ahmed; Kuo, Dong-Hau, E-mail: dhkuo@mail.ntust.edu.tw; Yassin, Jemal Mohammed; Ahmed, Kedir Ebrahim; Abdullah, Hairus

2017-07-15

Graphical abstract: Proposed charge separation mechanism and degradation of dye with photocatalyst under light irradiation. - Highlights: • n-type TiO{sub 2} inside and p-type Ag{sub 2}O outside was designed. • The p–n junction formation built in an electric field. • The p–n junction facilitates the electrons and holes separation. • The degradation of dye becomes more effective with Ag{sub 2}O/TiO{sub 2} catalyst. - Abstract: We develop the n-type TiO{sub 2} coated on SiO{sub 2} support abbreviated as SiO{sub 2}/TiO{sub 2} (ST) followed by deposition of p-type Ag{sub 2}O nanoparticles outside for the purpose of photocatalytic degradation of organic pollutants. Different composite catalysts were prepared with changing the amount AgNO{sub 3} (such as 0%, 5%, 10%, 20%, and 30%) and the composites were abbreviated as ST, STA-5, STA-10, STA-20, and STA-30, respectively. The composite catalysts were characterized with different techniques and tested for Rhodamine B (RhB) dye degradation under UV and visible light. Among the composite catalysts, the degradation efficiency of STA-20 was the highest and it degraded about 99% within 40 min under UV light-irradiation. However, the ST, STA-5, STA-10, and STA-30 composite catalysts could degrade about 21%, 47%, 58%, and 75% of the dye, respectively. Furthermore, the STA-5, STA-10, STA-20, and STA-30 composites were also tested and about 39%, 47%, 57%, and 42% of the dye, respectively, was degraded under visible light source. Hence, the formation of p–n junction heterostructure between n-type TiO{sub 2} and p-type Ag{sub 2}O could enhance the degradation of RhB in both UV and visible light irradiation. It could be also potentially applicable photocatalyst for environmental remediation.

Rejuvenation of the SCR catalyst at Mehrum

Energy Technology Data Exchange (ETDEWEB)

Nagai, Y.; Inatsume, Y.; Morita, I.; Kato, Y.; Yokoyama, K.; Ito, K. [Babcock Hitachi K.K., Kure-shi, Hiroshima-ken (Japan)

2004-07-01

Babcock Hitachi K.K. (BHK) received the contract of the rejuvenation of the SCR catalyst at the 750 MW coal-fired Mehrum Power Station (in Hohenhameln, Germany) in March 2003. The contractual coverage was 160 m{sup 3} of the entire catalyst layer. The catalyst, which had been in operation for 16 years since 1987, was originally supplied by BHK. The rejuvenation process developed for the Mehrum project consisted of two major steps: the first is to dust off the catalyst and remove the catalyst poison, and the second step is to add active material to enhance the catalyst activity. The catalyst must be dried after each washing. In order to minimize transportation cost and time, the rejuvenation work was done at the Mehrum station site. The scope of the rejuvenation work was shared between the owner and BHK. It took about one and a half months to complete the (total) on-site rejuvenation worked. The performance of the rejuvenated catalyst was superior to show the same level of activity as the unused catalyst and maintain the same SO{sub 2} conversion rate as the spent catalyst. This paper gives the details of the spent coal-fired SCR catalyst rejuvenation work. 13 figs., 1 tab.

Preparation and characterization of Pd doped ceria–ZnO nanocomposite catalyst for methyl tert-butyl ether (MTBE) photodegradation

International Nuclear Information System (INIS)

Seddigi, Zaki S.; Bumajdad, Ali; Ansari, Shahid P.; Ahmed, Saleh A.; Danish, Ekram Y.; Yarkandi, Naeema H.; Ahmed, Shakeel

2014-01-01

Highlights: • Novel Pd supported ceria–ZnO photocatalysts were prepared with different amounts of palladium. • The photocatalytic activity of these catalysts was evaluated for degradation of MTBE in water. • Near complete removal of MTBE was achieved using 1% Pd doped ceria–ZnO catalyst and UV irradiation. • Highest rate constant was obtained in case of 1% Pd doped ceria–ZnO catalyst. • Shape and size of pores are important factors for high photoactivity of catalyst. -- Abstract: A series of binary oxide catalysts (ceria–ZnO) were prepared and doped with different amounts of palladium in the range of 0.5%–1.5%. The prepared catalysts were characterized by SEM, TEM, XRD and XPS, as well as by N 2 sorptiometry study. The XPS results confirmed the structure of the Pd CeO 2−x -ZnO. The photocatalytic activity of these catalysts was evaluated for degradation of MTBE in water. These photocatalyst efficiently degrade a 100 ppm aqueous solution of MTBE upon UV irradiation for 5 h in the presence of 100 mg of each of these photocatalysts. The removal of 99.6% of the MTBE was achieved with the ceria–ZnO catalyst doped with 1% Pd. In addition to the Pd loading, the N 2 sorptiometry study introduced other factors that might affect the catalytic efficiency is the catalyst average pore sizes. The photoreaction was determined to be a first order reaction

Preparation and characterization of Pd doped ceria–ZnO nanocomposite catalyst for methyl tert-butyl ether (MTBE) photodegradation

Energy Technology Data Exchange (ETDEWEB)

Seddigi, Zaki S. [Chemistry Department, Umm Al-Qura University, Makkah (Saudi Arabia); Bumajdad, Ali [Chemistry Department, Faculty of Science, Kuwait University (Kuwait); Ansari, Shahid P. [Chemistry Department, Umm Al-Qura University, Makkah (Saudi Arabia); Ahmed, Saleh A., E-mail: saleh_63@hotmail.com [Chemistry Department, Umm Al-Qura University, Makkah (Saudi Arabia); Danish, Ekram Y. [Chemistry Department, King Abdulaziz University, Jeddah (Saudi Arabia); Yarkandi, Naeema H. [Chemistry Department, Umm Al-Qura University, Makkah (Saudi Arabia); Ahmed, Shakeel [Center for Refining and Petrochemicals, Research Institute, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia)

2014-01-15

Highlights: • Novel Pd supported ceria–ZnO photocatalysts were prepared with different amounts of palladium. • The photocatalytic activity of these catalysts was evaluated for degradation of MTBE in water. • Near complete removal of MTBE was achieved using 1% Pd doped ceria–ZnO catalyst and UV irradiation. • Highest rate constant was obtained in case of 1% Pd doped ceria–ZnO catalyst. • Shape and size of pores are important factors for high photoactivity of catalyst. -- Abstract: A series of binary oxide catalysts (ceria–ZnO) were prepared and doped with different amounts of palladium in the range of 0.5%–1.5%. The prepared catalysts were characterized by SEM, TEM, XRD and XPS, as well as by N{sub 2} sorptiometry study. The XPS results confirmed the structure of the Pd CeO{sub 2−x}-ZnO. The photocatalytic activity of these catalysts was evaluated for degradation of MTBE in water. These photocatalyst efficiently degrade a 100 ppm aqueous solution of MTBE upon UV irradiation for 5 h in the presence of 100 mg of each of these photocatalysts. The removal of 99.6% of the MTBE was achieved with the ceria–ZnO catalyst doped with 1% Pd. In addition to the Pd loading, the N{sub 2} sorptiometry study introduced other factors that might affect the catalytic efficiency is the catalyst average pore sizes. The photoreaction was determined to be a first order reaction.

TiO₂-Based Photocatalytic Geopolymers for Nitric Oxide Degradation.

Science.gov (United States)

Strini, Alberto; Roviello, Giuseppina; Ricciotti, Laura; Ferone, Claudio; Messina, Francesco; Schiavi, Luca; Corsaro, Davide; Cioffi, Raffaele

2016-06-24

This study presents an experimental overview for the development of photocatalytic materials based on geopolymer binders as catalyst support matrices. Particularly, geopolymer matrices obtained from different solid precursors (fly ash and metakaolin), composite systems (siloxane-hybrid, foamed hybrid), and curing temperatures (room temperature and 60 °C) were investigated for the same photocatalyst content (i.e., 3% TiO₂ by weight of paste). The geopolymer matrices were previously designed for different applications, ranging from insulating (foam) to structural materials. The photocatalytic activity was evaluated as NO degradation in air, and the results were compared with an ordinary Portland cement reference. The studied matrices demonstrated highly variable photocatalytic performance depending on both matrix constituents and the curing temperature, with promising activity revealed by the geopolymers based on fly ash and metakaolin. Furthermore, microstructural features and titania dispersion in the matrices were assessed by scanning electron microscopy (SEM) and energy dispersive X-ray (EDS) analyses. Particularly, EDS analyses of sample sections indicated segregation effects of titania in the surface layer, with consequent enhancement or depletion of the catalyst concentration in the active sample region, suggesting non-negligible transport phenomena during the curing process. The described results demonstrated that geopolymer binders can be interesting catalyst support matrices for the development of photocatalytic materials and indicated a large potential for the exploitation of their peculiar features.

New porous titanium–niobium oxide for photocatalytic degradation of bromocresol green dye in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Chaleshtori, Maryam Zarei, E-mail: mzarei@utep.edu [Materials Research and Technology Institute (MRTI), University of Texas at El Paso, 500W. University Ave., El Paso, TX 79968 (United States); Hosseini, Mahsa; Edalatpour, Roya [Materials Research and Technology Institute (MRTI), University of Texas at El Paso, 500W. University Ave., El Paso, TX 79968 (United States); Masud, S.M. Sarif [Department of Chemistry, University of Texas at El Paso, 500W. University Ave., El Paso, TX 79968 (United States); Chianelli, Russell R., E-mail: chianell@utep.edu [Materials Research and Technology Institute (MRTI), University of Texas at El Paso, 500W. University Ave., El Paso, TX 79968 (United States)

2013-10-15

Graphical abstract: The photocatalytic activity of different porous titanium–niobium oxides was evaluated toward degradation of bromocresol green (BG) under UV light. A better catalytic activity was observed for all samples at lower pH. Catalysts have a stronger ability for degradation of BG in acid media than in alkaline media. - Highlights: • Different highly structured titanium–niobium oxides have been prepared using improved methods of synthesis. • Photo-degradation of bromocresol green dye (BG) with nanostructure titanium–niobium oxide catalysts was carried out under UV light. • The photo-catalytic activity of all catalysts was higher in lower pH. • Titanium–niobium oxide catalysts are considerably stable and reusable. - Abstract: In this study, high surface area semiconductors, non porous and porous titanium–niobium oxides derived from KTiNbO{sub 5} were synthesized, characterized and developed for their utility as photocatalysts for decontamination with sunlight. These materials were then used in the photocatalytic degradation of bromocresol green dye (BG) in aqueous solution using UV light and their catalytic activities were evaluated at various pHs. For all catalysts, the photocatalytic degradation of BG was most efficient in acidic solutions. Results show that the new porous oxides have large porous and high surface areas and high catalytic activity. A topotactic dehydration treatment greatly improves catalyst performance at various pHs. Stability and long term activity of porous materials (topo and non-topo) in photocatalysis reactions was also tested. These results suggest that the new materials can be used to efficiently purify contaminated water.

Ferromagnetic resonance of cobalt nanoparticles used as a catalyst for the carbon nanotubes synthesis

Energy Technology Data Exchange (ETDEWEB)

Duraia, El-Shazly M. [Suez Canal University, Faculty of Science, Physics Department, Ismailia (Egypt); Al-Farabi Kazakh National University, Almaty (Kazakhstan); Institute of Physics and Technology, Almaty (Kazakhstan)], E-mail: duraia_physics@yahoo.com; Abdullin, Kh.A. [Institute of Physics and Technology, Almaty (Kazakhstan)

2009-12-15

Catalyst is considered to be the most crucial parameter for the growth of carbon nanotubes. In this work we study the ferromagnetic resonance (FMR) spectra of the catalyst nanoclusters. Moreover we report for the first time the angle FMR studies of catalyst particles with and without CNT layer. The dependencies of the FMR spectra, X-ray diffraction (XRD) patterns, Raman spectra and morphology of the CNT layers on the growth conditions are discussed.

Hollow Spheres of Iron Carbide Nanoparticles Encased in Graphitic Layers as Oxygen Reduction Catalysts

DEFF Research Database (Denmark)

Hu, Yang; Jensen, Jens Oluf; Zhang, Wei

2014-01-01

Nonprecious metal catalysts for the oxygen reduction reaction are the ultimate materials and the foremost subject for low‐temperature fuel cells. A novel type of catalysts prepared by high‐pressure pyrolysis is reported. The catalyst is featured by hollow spherical morphologies consisting...

Role of copper pyrovanadate as heterogeneous photo-Fenton like catalyst for the degradation of neutral red and azure-B: An eco-friendly approach

Energy Technology Data Exchange (ETDEWEB)

Kalal, Sangeeta; Ameta, Noopur; Kumar, Sudhish; Punjabi, Pinki Bala [M. L. Sukhadia University, Udaipur (India); Chauhan, Narendra Pal Singh [B. N. P. G. College, Udaipur (India); Ameta, Rakshit [PAHER University, Udaipur (India)

2014-12-15

The heterogeneous photo-Fenton like process is a green chemical pathway.. It has an edge over conventional Fenton and photo-Fenton processes as it does not require the removal of ferrous/ferric ions in the form of sludge. We prepared copper pyrovanadate or Volborthite (Cu{sub 3}V{sub 2}(OH){sub 2}O{sub 7}·2H{sub 2}O) composite photocatalyst by wet chemical method. The photocatalyst was characterized by SEM, XRD, IR, TGA/DSC, EDX and BET. Experiments demonstrated that catalyst could effectively catalyze degradation of neutral red and azure-B in presence of H{sub 2}O{sub 2} in visible light. Moreover, the photo-Fenton-like catalytic activity of Cu{sub 3}V{sub 2}(OH){sub 2}O{sub 7}·2H{sub 2}O was much higher than CuO and V{sub 2}O{sub 5}, when used alone as photocatalyst. The effect of variation of different parameters, i.e., pH, amount of photocatalyst, concentration of dye, amount of H{sub 2}O{sub 2} and light intensity was also investigated. The degradation was well fitted under pseudo-first-order reaction with a rate constant of 2.081x10{sup −4} sec{sup −1} and 3.876x10{sup −4} sec{sup −1} for neutral red and azure-B, respectively. Quality parameters of dye solutions before and after photo-Fenton degradation were also determined. A tentative mechanism involving •OH radical as an oxidant has been proposed. The high catalytic activity may be due to the Cu{sub 3}V{sub 2}(OH){sub 2}O{sub 7}·2H{sub 2}O shell, which not only increased the surface hydroxyl groups, but also enhanced the interfacial electron transfer.. The catalyst has been found to possess good recyclability.

Role of copper pyrovanadate as heterogeneous photo-Fenton like catalyst for the degradation of neutral red and azure-B: An eco-friendly approach

International Nuclear Information System (INIS)

Kalal, Sangeeta; Ameta, Noopur; Kumar, Sudhish; Punjabi, Pinki Bala; Chauhan, Narendra Pal Singh; Ameta, Rakshit

2014-01-01

The heterogeneous photo-Fenton like process is a green chemical pathway.. It has an edge over conventional Fenton and photo-Fenton processes as it does not require the removal of ferrous/ferric ions in the form of sludge. We prepared copper pyrovanadate or Volborthite (Cu_3V_2(OH)_2O_7·2H_2O) composite photocatalyst by wet chemical method. The photocatalyst was characterized by SEM, XRD, IR, TGA/DSC, EDX and BET. Experiments demonstrated that catalyst could effectively catalyze degradation of neutral red and azure-B in presence of H_2O_2 in visible light. Moreover, the photo-Fenton-like catalytic activity of Cu_3V_2(OH)_2O_7·2H_2O was much higher than CuO and V_2O_5, when used alone as photocatalyst. The effect of variation of different parameters, i.e., pH, amount of photocatalyst, concentration of dye, amount of H_2O_2 and light intensity was also investigated. The degradation was well fitted under pseudo-first-order reaction with a rate constant of 2.081x10"−"4 sec"−"1 and 3.876x10"−"4 sec"−"1 for neutral red and azure-B, respectively. Quality parameters of dye solutions before and after photo-Fenton degradation were also determined. A tentative mechanism involving •OH radical as an oxidant has been proposed. The high catalytic activity may be due to the Cu_3V_2(OH)_2O_7·2H_2O shell, which not only increased the surface hydroxyl groups, but also enhanced the interfacial electron transfer.. The catalyst has been found to possess good recyclability

Hydrothermal performance of catalyst supports

Energy Technology Data Exchange (ETDEWEB)

Elam, Jeffrey W.; Marshall, Christopher L.; Libera, Joseph A.; Dumesic, James A.; Pagan-Torres, Yomaira J.

2018-04-10

A high surface area catalyst with a mesoporous support structure and a thin conformal coating over the surface of the support structure. The high surface area catalyst support is adapted for carrying out a reaction in a reaction environment where the thin conformal coating protects the support structure within the reaction environment. In various embodiments, the support structure is a mesoporous silica catalytic support and the thin conformal coating comprises a layer of metal oxide resistant to the reaction environment which may be a hydrothermal environment.

Mixed phase Pt-Ru catalyst for direct methanol fuel cell anode by flame aerosol synthesis

DEFF Research Database (Denmark)

Chakraborty, Debasish; Bischoff, H.; Chorkendorff, Ib

2005-01-01

A spray-flame aerosol catalyzation technique was studied for producing Pt-Ru anode electrodes for the direct methanol fuel cell. Catalysts were produced as aerosol nanoparticles in a spray-flame reactor and deposited directly as a thin layer on the gas diffusion layer. The as-prepared catalyst wa......Ru1/Vulcan carbon. The kinetics of methanol oxidation on the mixed phase catalyst was also explored by electrochemical impedance spectroscopy. (c) 2005 The Electrochemical Society.......A spray-flame aerosol catalyzation technique was studied for producing Pt-Ru anode electrodes for the direct methanol fuel cell. Catalysts were produced as aerosol nanoparticles in a spray-flame reactor and deposited directly as a thin layer on the gas diffusion layer. The as-prepared catalyst...... was found to be a mixture of nanocrystalline, mostly unalloyed Pt and an amorphous phase mostly of Ru and to a lesser extent of Pt oxides on top of the crystalline phase. The flame-produced Pt1Ru1 demonstrated similar onset potential but similar to 60% higher activity compared to commercially available Pt1...

Deactivation of SCR catalysts by potassium: A study of potential alkali barrier materials

DEFF Research Database (Denmark)

Olsen, Brian Kjærgaard; Kügler, Frauke; Castellino, Francesco

2017-01-01

The use of coatings in order to protect vanadia based SCR catalysts against potassium poisoning has been studied by lab- and pilot-scale experiments. Three-layer pellets, consisting of a layer ofa potential coating material situated between layers of fresh and potassium poisoned SCR catalyst, were...... the coating process. Potassium had to some extent penetrated the MgO coat, and SEM analysis revealed it to be rather thick and fragile. Despite these observations, the coating did protect the SCR catalyst against potassium poisoning to some degree, leaving promise of further optimization....... used to test the ability of the barrier layer to block the diffusion of potassium across the pellet. Of MgO, sepiolite and Hollandite manganese oxide, MgO was the most effective potassium barrier, and no potassium was detected in the MgO layer upon exposure to SCR conditions for 7 days. Two monoliths...

Highly Dispersed Alloy Catalyst for Durability

Energy Technology Data Exchange (ETDEWEB)

Murthi, Vivek S.; Izzo, Elise; Bi, Wu; Guerrero, Sandra; Protsailo, Lesia

2013-01-08

Achieving DOE's stated 5000-hr durability goal for light-duty vehicles by 2015 will require MEAs with characteristics that are beyond the current state of the art. Significant effort was placed on developing advanced durable cathode catalysts to arrive at the best possible electrode for high performance and durability, as well as developing manufacturing processes that yield significant cost benefit. Accordingly, the overall goal of this project was to develop and construct advanced MEAs that will improve performance and durability while reducing the cost of PEMFC stacks. The project, led by UTC Power, focused on developing new catalysts/supports and integrating them with existing materials (membranes and gas diffusion layers (GDLs)) using state-of-the-art fabrication methods capable of meeting the durability requirements essential for automotive applications. Specifically, the project work aimed to lower platinum group metals (PGM) loading while increasing performance and durability. Appropriate catalysts and MEA configuration were down-selected that protects the membrane, and the layers were tailored to optimize the movements of reactants and product water through the cell to maximize performance while maintaining durability.

Synthesis and characterization of nanometal-ordered mesoporous carbon composites as heterogeneous catalysts for electrooxidation of aniline

International Nuclear Information System (INIS)

Duan, Xiaoyue; Chen, Yawen; Liu, Xinyue; Chang, Limin

2017-01-01

Highlights: •NM-OMC catalysts were prepared for electrochemical oxidation of aniline. •The oxidation of aniline was studied with NM-OMC catalysts suspended in solution. •The Cu-OMC exhibited the highest catalytic activity for aniline degradation. •The mineralization current efficiency was improved by 2 times with Cu-OMC catalyst. •An electrochemical mineralization pathway of aniline was proposed. -- Abstract: The Cu, Co and Ni nanometal embedded ordered mesoporous carbons (NM-OMCs) were fabricated by a soft-template method using phenol/formaldehyde as carbon source and triblock copolymer F127 as template agent. The morphology, structure, surface physicochemical properties and pore structure of the NM-OMCs were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and nitrogen adsorption-desorption isotherms. Their potential application to the electrocatalytic degradation of aniline was investigated using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and ·OH radicals generation test. Furthermore, the electrochemical oxidation process of aniline was also investigated in the presence of the OMC-based catalyst particles suspended in a Na 2 SO 4 solution using a PbO 2 anode. Results revealed that the NM-OMCs inherited the ordered mesostructure of pristine OMC and the metal nanoparticles (Cu, Co or Ni) were embedded in the carbon framework. The Cu-OMC exhibited significantly higher catalytic activity than OMC and other NM-OMCs for the electrooxidation of aniline. In electrochemical oxidation process of aniline, nearly all of aniline could be degraded after 120 min of electrolysis with Cu-OMC particles as catalyst, while 89%, 92%, and 97% with OMC, Co-OMC and Ni-OMC catalysts, respectively, obviously higher than 76% of electrochemical oxidation without assistance of catalysts. After

Fundamental degradation mechanisms of layered oxide Li-ion battery cathode materials: Methodology, insights and novel approaches

International Nuclear Information System (INIS)

Hausbrand, R.; Cherkashinin, G.; Ehrenberg, H.; Gröting, M.; Albe, K.; Hess, C.; Jaegermann, W.

2015-01-01

Graphical abstract: - Highlights: • Description of recent in operando and in situ analysis methodology. • Surface science approach using photoemission for analysis of cathode surfaces and interfaces. • Ageing and fatigue of layered oxide Li-ion battery cathode materials from the atomistic point of view. • Defect formation and electronic structure evolution as causes for cathode degradation. • Significance of interfacial energy alignment and contact potential for side reactions. - Abstract: This overview addresses the atomistic aspects of degradation of layered LiMO 2 (M = Ni, Co, Mn) oxide Li-ion battery cathode materials, aiming to shed light on the fundamental degradation mechanisms especially inside active cathode materials and at their interfaces. It includes recent results obtained by novel in situ/in operando diffraction methods, modelling, and quasi in situ surface science analysis. Degradation of the active cathode material occurs upon overcharge, resulting from a positive potential shift of the anode. Oxygen loss and eventual phase transformation resulting in dead regions are ascribed to changes in electronic structure and defect formation. The anode potential shift results from loss of free lithium due to side reactions occurring at electrode/electrolyte interfaces. Such side reactions are caused by electron transfer, and depend on the electron energy level alignment at the interface. Side reactions at electrode/electrolyte interfaces and capacity fade may be overcome by the use of suitable solid-state electrolytes and Li-containing anodes

Implications Enzymatic Degradation of the Endothelial Glycocalyx on the Microvascular Hemodynamics and the Arteriolar Red Cell Free Layer of the Rat Cremaster Muscle

Directory of Open Access Journals (Sweden)

Ozlem Yalcin

2018-03-01

Full Text Available The endothelial glycocalyx is a complex network of glycoproteins, proteoglycans, and glycosaminoglycans; it lines the vascular endothelial cells facing the lumen of blood vessels forming the endothelial glycocalyx layer (EGL. This study aims to investigate the microvascular hemodynamics implications of the EGL by quantifying changes in blood flow hydrodynamics post-enzymatic degradation of the glycocalyx layer. High-speed intravital microscopy videos of small arteries (around 35 μm of the rat cremaster muscle were recorded at various time points after enzymatic degradation of the EGL. The thickness of the cell free layer (CFL, blood flow velocity profiles, and volumetric flow rates were quantified. Hydrodynamic effects of the presence of the EGL were observed in the differences between the thickness of CFL in microvessels with an intact EGL and glass tubes of similar diameters. Maximal changes in the thickness of CFL were observed 40 min post-enzymatic degradation of the EGL. Analysis of the frequency distribution of the thickness of CFL allows for estimation of the thickness of the endothelial surface layer (ESL, the plasma layer, and the glycocalyx. Peak flow, maximum velocity, and mean velocity were found to statistically increase by 24, 27, and 25%, respectively, after enzymatic degradation of the glycocalyx. The change in peak-to-peak maximum velocity and mean velocity were found to statistically increase by 39 and 32%, respectively, after 40 min post-enzymatic degradation of the EGL. The bluntness of blood flow velocity profiles was found to be reduced post-degradation of the EGL, as the exclusion volume occupied by the EGL increased the effective volume impermeable to RBCs in microvessels. This study presents the effects of the EGL on microvascular hemodynamics. Enzymatic degradation of the EGL resulted in a decrease in the thickness of CFL, an increase in blood velocity, blood flow, and decrease of the bluntness of the blood flow

Implications Enzymatic Degradation of the Endothelial Glycocalyx on the Microvascular Hemodynamics and the Arteriolar Red Cell Free Layer of the Rat Cremaster Muscle.

Science.gov (United States)

Yalcin, Ozlem; Jani, Vivek P; Johnson, Paul C; Cabrales, Pedro

2018-01-01

The endothelial glycocalyx is a complex network of glycoproteins, proteoglycans, and glycosaminoglycans; it lines the vascular endothelial cells facing the lumen of blood vessels forming the endothelial glycocalyx layer (EGL). This study aims to investigate the microvascular hemodynamics implications of the EGL by quantifying changes in blood flow hydrodynamics post-enzymatic degradation of the glycocalyx layer. High-speed intravital microscopy videos of small arteries (around 35 μm) of the rat cremaster muscle were recorded at various time points after enzymatic degradation of the EGL. The thickness of the cell free layer (CFL), blood flow velocity profiles, and volumetric flow rates were quantified. Hydrodynamic effects of the presence of the EGL were observed in the differences between the thickness of CFL in microvessels with an intact EGL and glass tubes of similar diameters. Maximal changes in the thickness of CFL were observed 40 min post-enzymatic degradation of the EGL. Analysis of the frequency distribution of the thickness of CFL allows for estimation of the thickness of the endothelial surface layer (ESL), the plasma layer, and the glycocalyx. Peak flow, maximum velocity, and mean velocity were found to statistically increase by 24, 27, and 25%, respectively, after enzymatic degradation of the glycocalyx. The change in peak-to-peak maximum velocity and mean velocity were found to statistically increase by 39 and 32%, respectively, after 40 min post-enzymatic degradation of the EGL. The bluntness of blood flow velocity profiles was found to be reduced post-degradation of the EGL, as the exclusion volume occupied by the EGL increased the effective volume impermeable to RBCs in microvessels. This study presents the effects of the EGL on microvascular hemodynamics. Enzymatic degradation of the EGL resulted in a decrease in the thickness of CFL, an increase in blood velocity, blood flow, and decrease of the bluntness of the blood flow velocity profile in

Carbon nanocages: a new support material for Pt catalyst with remarkably high durability.

Science.gov (United States)

Wang, Xiao Xia; Tan, Zhe Hua; Zeng, Min; Wang, Jian Nong

2014-03-24

Low durability is the major challenge hindering the large-scale implementation of proton exchange membrane fuel cell (PEMFC) technology, and corrosion of carbon support materials of current catalysts is the main cause. Here, we describe the finding of remarkably high durability with the use of a novel support material. This material is based on hollow carbon nanocages developed with a high degree of graphitization and concurrent nitrogen doping for oxidation resistance enhancement, uniform deposition of fine Pt particles, and strong Pt-support interaction. Accelerated degradation testing shows that such designed catalyst possesses a superior electrochemical activity and long-term stability for both hydrogen oxidation and oxygen reduction relative to industry benchmarks of current catalysts. Further testing under conditions of practical fuel cell operation reveals almost no degradation over long-term cycling. Such a catalyst of high activity, particularly, high durability, opens the door for the next-generation PEMFC for "real world" application.

Endurance testing of a WDS catalyst

International Nuclear Information System (INIS)

Vladu, Mihaela; Brad, Sebastian; Vijulie, Mihai; Vasut, Felicia; Constantin, Marin

2007-01-01

Full text: The Water Detritiation System (WDS) of ITER is a safety related component since it is the final barrier against tritium discharge into the environment. Therefore, its subcomponents have to be qualified and predictions on the time evolution of performances have to be made. During the activities devoted to JET WDS, test at lower concentrations of tritium and at small scale have been performed. The goal of this work is to extend the endurance testings and to check early results by tests under relevant conditions. The degradation of the WDS catalyst can strongly affect its separation performances and consequently it will entail a raise of the tritium releases into the environment. If a catalyst based on Teflon material is used for the LPCE column of WDS, the fluoride that may be formed and released due to the tritium presence causes the corrosion of the LPCE column with unpredictable effects. Therefore the quantification of catalyst degradation and the amount of fluoride released is needed for planning the maintenance activities and to predict the operation life time of the WDS components. The manufacturing of hydrophobic catalysts with activity that is not lowered by liquid water determined the rise of interest for the isotopes separation techniques in the hydrogen - water system. The active component of these catalysts is Pt (the only material to be further discussed) that enhances the exchange between the hydrogen and water vapors. The hydrophobic support does not allow the wetting and blocking by water of the active surface. Hydrophobic catalysts were manufactured by two methods: - direct deposition of Pt into the pores of a hydrophobic support (Teflon, carbon monofluoride, poly styrene, styrene di-vinyl benzene, etc.); - deposition on a hydrophilic support, most common charcoal, followed by hydrophobization by silicon oil or by homogenizing with hydrophobic polymer (Teflon, silicon resins). This type of catalysts is one of the most studied groups due to

Photodegradation of Methyl Green by Nickel-Dimethylglyoxime/ZSM-5 Zeolite as a Heterogeneous Catalyst

Directory of Open Access Journals (Sweden)

Alireza Nezamzadeh-Ejhieh

2013-01-01

Full Text Available Ni-DMG/ZSM-5 zeolite was prepared by ion exchange and complexation procedures. FT-IR, XRD, SEM, TG, and DTG methods were used for characterization of the raw and modified samples. The prepared composite was used as a catalyst in the photodegradation process of an aqueous solution methyl green (MG dye under UV irradiation. The effect of key operating parameters such as catalyst dosage, temperature, the initial concentration of the dye, and pH of the samples was studied on the degradation extent of the dye. UV-Vis spectrophotometric measurements were performed for determination of the decolorization and mineralization extents. The optimal operation parameters were found as follows: , temperature of 60°C, 0.6 g L−1 of the catalyst, and 40 ppm of the dye concentration. The Ni-DMG particles out of zeolite framework did not show significant degradation efficiency. The degradation process obeys the first-order kinetic.

Active carbon catalyst for heavy oil upgrading

Energy Technology Data Exchange (ETDEWEB)

Fukuyama, Hidetsugu; Terai, Satoshi [Technology Research Center, Toyo Engineering Corporation, 1818 Azafujimi, Togo, Mobara-shi, Chiba 297-00017 (Japan); Uchida, Masayuki [Business Planning and Exploring Department, Overseas Business Development and Marketing Division, Toyo Engineering Corporation, 2-8-1 Akanehama, Narashino-shi, Chiba 275-0024 (Japan); Cano, Jose L.; Ancheyta, Jorge [Maya Crude Treatment Project, Instituto Mexicano del Petroleo, Eje Central Lazaro Cardenas No. 152, Col. San Bartolo Atepehuacan, Mexico D.F. 07730 (Mexico)

2004-11-24

The active carbon (AC) catalyst was studied by hydrocracking of Middle Eastern vacuum residue (VR) for heavy oil upgrading. It was observed that the active carbon has the affinity to heavy hydrocarbon compounds and adsorption selectivity to asphaltenes, and exhibits better ability to restrict the coke formation during the hydrocracking reaction of VR. The mesopore of active carbon was thought to play an important role for effective conversion of heavy hydrocarbon compounds into lighter fractions restricting carbon formation. The performance of the AC catalyst was examined by continuous hydrocracking by CSTR for the removal of such impurities as sulfur and heavy metals (nickel and vanadium), which are mostly concentrated in the asphaltenes. The AC catalyst was confirmed to be very effective for the removal of heavy metals from Middle Eastern VR, Maya/Istmo VR and Maya VR. The extruded AC catalysts were produced by industrial manufacturing method. The application test of the extruded AC catalyst for ebullating-bed reactor as one of the commercially applicable reactors was carried out at the ebullating-bed pilot plant for 500h. The ebullition of the extruded AC catalyst was successfully traced and confirmed by existing {gamma}-ray density meter. The extruded AC catalyst showed stable performance with less sediment formation at an equivalent conversion by conventional alumina catalyst at commercial ebullating-bed unit. The degradation of the AC catalyst at the aging test was observed to be less than that of the conventional alumina catalyst. Thus, the AC catalyst was confirmed to be effective and suitable for upgrading of heavy oil, especially such heavy oils as Maya, which contains much heavy metals.

Studies on PEM fuel cell noble metal catalyst dissolution

DEFF Research Database (Denmark)

Andersen, S. M.; Grahl-Madsen, L.; Skou, E. M.

2011-01-01

A combination of electrochemical, spectroscopic and gravimetric methods was carried out on Proton Exchange Membrane (PEM) fuel cell electrodes with the focus on platinum and ruthenium catalysts dissolution, and the membrane degradation. In cyclic voltammetry (CV) experiments, the noble metals were...... found to dissolve in 1 M sulfuric acid solution and the dissolution increased exponentially with the upper potential limit (UPL) between 0.6 and 1.6 vs. RHE. 2-20% of the Pt (depending on the catalyst type) was found to be dissolved during the experiments. Under the same conditions, 30-100% of the Ru...... (depending on the catalyst type) was found to be dissolved. The faster dissolution of ruthenium compared to platinum in the alloy type catalysts was also confirmed by X-ray diffraction measurements. The dissolution of the carbon supported catalyst was found one order of magnitude higher than the unsupported...

Heat and mass transfer in a reforming catalyst bed. Analytical prediction of distributions in the catalyst bed; Kaishitsu shokubaiso ni okeru netsu oyobi busshitsu ido. Suchi kaiseki ni yoru sonai bunpu no yosoku

Energy Technology Data Exchange (ETDEWEB)

Usami, Y [Tokyo Electric Power Co. Inc., Tokyo (Japan); Fukusako, S; Yamada, M [Hokkaido University, Sapporo (Japan)

2000-01-25

Heat and mass transfer characteristics within a reforming catalyst bed have been analytically investigated. A numerical analysis was carried out in a two-dimensional steady-state model of reforming catalyst layer. Reforming tube was filled with catalyst and the tube wall was uniformly heated, a mixture of steam and methane was reformed through the catalyst bed. Predicted temperature, formed gas composition, methane conversion rate, and heat transfer coefficient distributions in the catalyst layer showed good agreement with experimental data. The effects of space velocity, steam carbon molar ratio, and wall temperature on the heat transfer coefficient were analytically presented. From temperature and composition distributions simulated by two-dimensional analysis, the effects of these factors above mentioned and diffusion on the transport phenomena were qualitatively predicted. (author)

Effect of hydrophobic additive on oxygen transport in catalyst layer of proton exchange membrane fuel cells

Science.gov (United States)

Wang, Shunzhong; Li, Xiaohui; Wan, Zhaohui; Chen, Yanan; Tan, Jinting; Pan, Mu

2018-03-01

Oxygen transport resistance (OTR) is a critical factor influencing the performance of proton exchange membrane fuel cells (PEMFCs). In this paper, an effective method to reduce the OTR of catalyst layers (CLs) by introducing a hydrophobic additive into traditional CLs is proposed. A low-molecular-weight polytetrafluoroethylene (PTFE) is selected for its feasibility to prepare an emulsion, which is mixed with a traditional catalyst ink to successfully fabricate the CL with PTFE of 10 wt%. The PTFE film exists in the mesopores between the carbon particles. The limiting current of the hydrophobic CL was almost 4000 mA/cm2, which is 500 mA/cm2 higher than that of the traditional CL. PTFE reduces the OTR of the CL in the dry region by as much as 24 s/m compared to the traditional CL and expands the dry region from 2000 mA/cm2 in the traditional CL to 2500 mA/cm2. Furthermore, the CL with the hydrophobic agent can improve the oxygen transport in the wet region (>2000 mA/cm2) more effectively than that in the dry region. All these results indicate that the CL with the hydrophobic agent shows a superior performance in terms of optimizing water management and effectively reduces the OTR in PEMFCs.

TiO2-Based Photocatalytic Geopolymers for Nitric Oxide Degradation

Science.gov (United States)

Strini, Alberto; Roviello, Giuseppina; Ricciotti, Laura; Ferone, Claudio; Messina, Francesco; Schiavi, Luca; Corsaro, Davide; Cioffi, Raffaele

2016-01-01

This study presents an experimental overview for the development of photocatalytic materials based on geopolymer binders as catalyst support matrices. Particularly, geopolymer matrices obtained from different solid precursors (fly ash and metakaolin), composite systems (siloxane-hybrid, foamed hybrid), and curing temperatures (room temperature and 60 °C) were investigated for the same photocatalyst content (i.e., 3% TiO2 by weight of paste). The geopolymer matrices were previously designed for different applications, ranging from insulating (foam) to structural materials. The photocatalytic activity was evaluated as NO degradation in air, and the results were compared with an ordinary Portland cement reference. The studied matrices demonstrated highly variable photocatalytic performance depending on both matrix constituents and the curing temperature, with promising activity revealed by the geopolymers based on fly ash and metakaolin. Furthermore, microstructural features and titania dispersion in the matrices were assessed by scanning electron microscopy (SEM) and energy dispersive X-ray (EDS) analyses. Particularly, EDS analyses of sample sections indicated segregation effects of titania in the surface layer, with consequent enhancement or depletion of the catalyst concentration in the active sample region, suggesting non-negligible transport phenomena during the curing process. The described results demonstrated that geopolymer binders can be interesting catalyst support matrices for the development of photocatalytic materials and indicated a large potential for the exploitation of their peculiar features. PMID:28773634

TiO2-Based Photocatalytic Geopolymers for Nitric Oxide Degradation

Directory of Open Access Journals (Sweden)

Alberto Strini

2016-06-01

Full Text Available This study presents an experimental overview for the development of photocatalytic materials based on geopolymer binders as catalyst support matrices. Particularly, geopolymer matrices obtained from different solid precursors (fly ash and metakaolin, composite systems (siloxane-hybrid, foamed hybrid, and curing temperatures (room temperature and 60 °C were investigated for the same photocatalyst content (i.e., 3% TiO2 by weight of paste. The geopolymer matrices were previously designed for different applications, ranging from insulating (foam to structural materials. The photocatalytic activity was evaluated as NO degradation in air, and the results were compared with an ordinary Portland cement reference. The studied matrices demonstrated highly variable photocatalytic performance depending on both matrix constituents and the curing temperature, with promising activity revealed by the geopolymers based on fly ash and metakaolin. Furthermore, microstructural features and titania dispersion in the matrices were assessed by scanning electron microscopy (SEM and energy dispersive X-ray (EDS analyses. Particularly, EDS analyses of sample sections indicated segregation effects of titania in the surface layer, with consequent enhancement or depletion of the catalyst concentration in the active sample region, suggesting non-negligible transport phenomena during the curing process. The described results demonstrated that geopolymer binders can be interesting catalyst support matrices for the development of photocatalytic materials and indicated a large potential for the exploitation of their peculiar features.

Catalyst Degradation Under Potential Cycling as an Accelerated Stress Test for PBI-Based High-Temperature PEM Fuel Cells - Effect of Humidification

DEFF Research Database (Denmark)

Søndergaard, Tonny; Cleemann, Lars Nilausen; Zhong, Lijie

2018-01-01

In the present work, high-temperature polymer electrolyte membrane fuel cells were subjected to accelerated stress tests of 30,000 potential cycles between 0.6 and 1.0 V at 160 textdegreeC (133 h cycling time). The effect that humidity has on the catalyst durability was studied by testing either...... with or without humidification of the nitrogen that was used as cathode gas during cycling segments. Pronounced degradation was seen from the polarization curves in both cases, though permanent only in the humidified case. In the unhumidified case, the performance loss was more or less recoverable following 24 h...

Photocatalytic degradation of indigo carmine by ZnO photocatalyst under visible light irradiation

Directory of Open Access Journals (Sweden)

Ali Al- Taie

2017-09-01

Full Text Available In this work, the photocatalytic degradation of indigo carmine (IC using zinc oxide suspension was studied. The effect of influential parameters such as initial indigo carmine concentration and catalyst loading were studied with the effect of Vis irradiation in the presence of reused ZnO was also investigated. The increased in initial dye concentration decreased the photodegradation and the increased catalyst loading increased the degradation percentage and the reused-ZnO exhibits lower photocatalytic activity than the ZnO catalyst. It has been found that the photocatalytic degradation of indigo carmine obeyed the pseudo-first-order kinetic reaction in presence of zinc oxide. This was found from plotting the relationship between ln (C0/Ct and irradiation the rate constant of the process.UV- spectrophotometer was used to study the indigo carmine photodegradation

Durable platinum/graphene catalysts assisted with polydiallyldimethylammonium for proton-exchange membrane fuel cells

International Nuclear Information System (INIS)

Lei, M.; Liang, C.; Wang, Y.J.; Huang, K.; Ye, C.X.; Liu, G.; Wang, W.J.; Jin, S.F.; Zhang, R.; Fan, D.Y.; Yang, H.J.; Wang, Y.G.

2013-01-01

High performance and electrochemically stable Pt/graphene catalysts assisted with polydiallyldimethylammonium (PDDA) have been synthesized for PEM fuel cells. The preparation procedure and properties of the catalysts are investigated in detail. With the introduction of PDDA molecules, Pt nanoparticles can be well-dispersed on graphene support, resulting in improved electrochemical surface area and enhanced electrocatalytic activity. The corresponding electrochemical surface areas (ECSA) of catalyst layers calculated from the hydrogen desorption peak on cyclic voltammogram curves are 78.3, 72.5 and 73.6 cm 2 g −1 for catalyst layers with Pt/graphene, Pt-PDDA/graphene, and Pt/graphene-PDDA catalysts, respectively. Both PDDA modified Pt nanoparticles and PDDA modified graphene supports also exhibit high durability toward electrochemical oxidation cycles compared with the conventional produced Pt/graphene catalyst at the same conditions. After 3000 cycles, only 23.52% of the initial ECSA remains for Pt/graphene electrocatalyst whereas 43.04% and 37.7% of the initial ECSA for the Pt/graphene-PDDA and Pt-PDDA/graphene catalysts remain, respectively

Conditions for reduction of ironmolybdenum-tungsten catalyst for ammonia synthesis

International Nuclear Information System (INIS)

Simulina, N.A.; Karibdzhanyan, N.A.; Lachinov, S.S.; Anfimov, V.A.; Shumlyakovskij, Ts.I.

1977-01-01

The reduction of Fe-Mo-W catalyst MB-5, used for synthesis of ammonia, has been studied in the reactor of extracolumn reduction. The results obtained have been compared with similar results for the catalyst CA-1. It has been shown that reduction of the catalyst MB-5 proceeds more intensive and is completed at lower temperature and for a shorter period of time. The samples of the catalyst MB-5 discharged from different layers in the reactor are more active than CA-1 reduced under identical conditions

The Effect of Platinum Electrocatalyst on Membrane Degradation in Polymer Electrolyte Fuel Cells.

Science.gov (United States)

Bodner, Merit; Cermenek, Bernd; Rami, Mija; Hacker, Viktor

2015-12-08

Membrane degradation is a severe factor limiting the lifetime of polymer electrolyte fuel cells. Therefore, obtaining a deeper knowledge is fundamental in order to establish fuel cells as competitive product. A segmented single cell was operated under open circuit voltage with alternating relative humidity. The influence of the catalyst layer on membrane degradation was evaluated by measuring a membrane without electrodes and a membrane-electrode-assembly under identical conditions. After 100 h of accelerated stress testing the proton conductivity of membrane samples near the anode and cathode was investigated by means of ex situ electrochemical impedance spectroscopy. The membrane sample near the cathode inlet exhibited twofold lower membrane resistance and a resulting twofold higher proton conductivity than the membrane sample near the anode inlet. The results from the fluoride ion analysis have shown that the presence of platinum reduces the fluoride emission rate; which supports conclusions drawn from the literature.

Synergetic effect of Ag_2O as co-catalyst for enhanced photocatalytic degradation of phenol on N-TiO_2

International Nuclear Information System (INIS)

Chu, Haipeng; Liu, Xinjuan; Liu, Junying; Li, Jinliang; Wu, Tianyang; Li, Haokun; Lei, Wenyan; Xu, Yan; Pan, Likun

2016-01-01

Graphical abstract: Ag_2O/N-TiO_2 composites were synthesized via a co-precipitation method for visible light photocatalytic degradation of organic pollutions with excellent photocatalytic activity. - Highlights: • Ag_2O/N-TiO_2 composites were synthesized via a facile precipitation method. • Ag_2O/N-TiO_2 composites exhibited enhanced photocatalytic activity. • Ag_2O acts as co-catalyst to separate the photo-generated electron-hole pairs. - Abstract: A facile precipitation method was developed to synthesize the Ag_2O/N-TiO_2 composites. Their morphology, structure and photocatalytic performance in the degradation of methylene blue (MB) and phenol under visible light irradiation were characterized by scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, photoluminescence spectroscopy and UV–vis absorption spectroscopy, respectively. The results show that the Ag_2O/N-TiO_2 composites exhibit excellent photocatalytic performance. The maximum degradation rates of MB and phenol are about 8.9 and 2.9 times that of pure N-TiO_2, respectively. The excellent photocatalytic performance is mainly ascribed to the synergetic effects of Ag_2O and N-TiO_2 including the increased light absorption and the reduced electron-hole pair recombination in N-TiO_2 with the presence of Ag_2O.

Catalyst-free growth of ZnO nanowires on ITO seed/glass by thermal evaporation method: Effects of ITO seed layer thickness

Energy Technology Data Exchange (ETDEWEB)

Alsultany, Forat H., E-mail: foratusm@gmail.com; Ahmed, Naser M. [School of Physics, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Hassan, Z. [Institute of Nano-Optoelectronics Research and Technology Laboratory (INOR), Universiti Sains Malaysia, 11800 USM, Penang (Malaysia)

2016-07-19

A seed/catalyst-free growth of ZnO nanowires (ZnO-NWs) on a glass substrate were successfully fabricated using thermal evaporation technique. These nanowires were grown on ITO seed layers of different thicknesses of 25 and 75 nm, which were deposited on glass substrates by radio frequency (RF) magnetron sputtering. Prior to synthesized ITO nanowires, the sputtered ITO seeds were annealed using the continuous wave (CW) CO2 laser at 450 °C in air for 15 min. The effect of seed layer thickness on the morphological, structural, and optical properties of ZnO-NWs were systematically investigated by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and UV-Vis spectrophotometer.

Reductive dechlorination of tetrachlorobisphenol A by Pd/Fe bimetallic catalysts

International Nuclear Information System (INIS)

Huang, Qiang; Liu, Wen; Peng, Ping’an; Huang, Weilin

2013-01-01

Highlights: • TCBPA can be rapidly and completely dechlorinated by Pd/Fe bimetallic catalysts. • The observed rate constants are functions of dosages, initial concentration, Pd coverage and solution pH. • Pd dosage is the major factor in the observed rates of the reaction. • This is the first report investigating the dechlorination of TCBPA by Pd/Fe catalysts. -- Abstract: The Pd/Fe bimetallic catalysts of micron sizes were synthesized and the rates of tetrachlorobisphenol A (TCBPA) degradation were measured under various conditions using a batch reactor system. The results showed that TCBPA was rapidly dechlorinated to tri-, di- and mono-chlorobisphenol A and to bisphenol A (BPA). The observed rate constants (k obs ) were found to increase as functions of the Pd coverage on the Fe particles and the dosages of the catalysts within the reactors. The k obs value decreased as the initial TCBPA concentration increased, suggesting that the TCBPA dechlorination may follow a surface-site limiting Langmuir–Hinshelwood rate model. The weakly acidic solution, especially at or near pH 6.0, also favored the dechlorination of TCBPA. At pH 6.0, Pd coverage of 0.044 wt% and catalyst dosage of 5 g L −1 , TCBPA with an initial concentration of 20 μM was completely transformed within 60 min, and BPA was detected as the major product through the reaction time. Meanwhile, the k obs values measured at constant solution pH correlated linearly with the mass of particle-bound Pd introduced to the reactors, regardless of Pd/Fe catalyst dosage or Pd surface coverage. This study suggested that Pd/Fe catalysts could be potentially employed to rapidly degrade TCBPA in the contaminated environment

Self-regenerative function of the intelligent automotive catalyst

International Nuclear Information System (INIS)

Tanaka, Hirohisa; Nishihata, Yasuo

2007-01-01

Intelligent catalyst, in which noble metals are used as an active part of automotive catalyst, has been considered for keeping up their sufficient activity. The noble metals have a function of cleaning up the exhaust gas as well as that of self-regeneration. In 2002, a Pd system has been put to practical use, and continuously Rh and Pt systems have been commercialized. Now the catalyst has been used in more than three million vehicles. In this report, the atomic level mechanism of the catalyst and its self-regeneration function getting from analyses using synchrotron radiation are introduced. By the analysis using the Spring-8, the mechanism of keeping the active state of the Pd Perovskite Oxide without degradation was identified. The DXAFS (Dispersive X-ray Absorption Fine Structure) analysis in the ESRF (European Synchrotron Radiation Facility) made clear the self-regeneration mechanism of the Pd Perovskite Oxide. This knowledge could lead to the practical development of the Rh and Pt systems. The catalyst technology is counted on balancing resources of the noble metal and environmental sustainability. (A.H.)

The optimization, kinetics and mechanism of m-cresol degradation via catalytic wet peroxide oxidation with sludge-derived carbon catalyst

Energy Technology Data Exchange (ETDEWEB)

Wang, Yamin [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Wei, Huangzhao; Zhao, Ying [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Sun, Wenjing [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Sun, Chenglin, E-mail: clsun@dicp.ac.cn [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China)

2017-03-15

Highlights: • The sludge derived carbon modified with 0 °C acid was used as catalyst in CWPO. • RSM was used to optimize CWPO reaction conditions of m-cresol for the first time. • The kinetic model was disclosed to be correlated with residue target concentration. • The proposed degradation pathways of m-cresol were well proven by DFT method. - Abstract: The sludge-derived carbon catalyst modified with 0 °C HNO{sub 3} solution was tested in catalytic wet peroxide oxidation of m-cresol (100 mg L{sup −1}) with systematical mathematical models and theoretical calculation for the first time. The reaction conditions were optimized by response surface methodology (RSM) as T = 60 °C, initial pH = 3.0, C{sub 0,H2O2(30%)} = 1.20 g L{sup −1} (lower than the stoichiometric amount of 1.80 g L{sup −1}) and C{sub cat} = 0.80 g L{sup −1}, with 96% of m-cresol and 47% of TOC converted after 16 min and 120 min of reaction, respectively, and ξ (mg TOC/g H{sub 2}O{sub 2} fed) = 83.6 mg/g. The end time of the first kinetic period in m-cresol model was disclosed to be correlated with the fixed residue m-cresol concentration of about 33%. Furthermore, the kinetic constants in models of TOC and H{sub 2}O{sub 2} exactly provide convincing proof of three-dimensional response surfaces analysis by RSM, which showed the influence of the interaction between organics and H{sub 2}O{sub 2} on effective H{sub 2}O{sub 2} utilization. The reaction intermediates over time were identified by gas chromatography–mass spectrometer based on kinetics analysis. Four degradation pathways for m-cresol were proposed, of which the possibility and feasibility were well proven by frontier molecule orbital theory and atomic charge distribution via density functional theory method.

Sonocatalytic Degradation of Antibiotics Tetracycline by Mn-Modified Diatomite

Directory of Open Access Journals (Sweden)

Yiping Guo

2017-01-01

Full Text Available Mn-modified diatomite was prepared by wet impregnation and subsequent calcinations processes. It was used as catalyst for sonocatalytic degradation of antibiotics tetracycline. Characterizations by scanning electron microscopy and X-ray diffraction pattern showed that the morphology and crystal structure of the modified diatomite were similar to these of raw diatomite. Despite containing very limited amount of Mn oxides, the Mn-modified diatomite showed much higher sonocatalytic activity than the raw diatomite. The increases in both MnSO4 concentration of the wet impregnation solution and the catalyst dosage could enhance the degradation of antibiotics tetracycline significantly. Kapp values for ultrasonication, catalyst adsorption, and both processes combined (0.10 mol/L MnSO4-modified diatomite were 1.22 × 10−4, 0.00193, and 0.00453 min−1, respectively, while the corresponding values of R2 were 0.956, 0.986, and 0.953, respectively. These results demonstrated the significant synergetic effect by combining ultrasonication and catalyst adsorption processes. The presence of isopropanol, KBr, and NaN3 quenched a series of reactive oxygen species sharply, indicating the dominant role of reactive oxygen species in the sonocatalytic process. In contrast, the addition of Fe(II enhanced the degradation due to the generation of more OH∙ radicals in the concurrent Fenton reaction. All the results indicated that Mn-modified diatomite had the great potential for water treatment by sonocatalytic oxidation.

Study on Endurance and Performance of Impregnated Ruthenium Catalyst for Thruster System.

Science.gov (United States)

Kim, Jincheol; Kim, Taegyu

2018-02-01

Performance and endurance of the Ru catalyst were studied for nitrous oxide monopropellant thruster system. The thermal decomposition of N2O requires a considerably high temperature, which make it difficult to be utilized as a thruster propellant, while the propellant decomposition temperature can be reduced by using the catalyst through the decomposition reaction with the propellant. However, the catalyst used for the thruster was frequently exposed to high temperature and high-pressure environment. Therefore, the state change of the catalyst according to the thruster operation was analyzed. Characterization of catalyst used in the operation condition of the thruster was performed using FE-SEM and EDS. As a result, performance degradation was occurred due to the volatilization of Ru catalyst and reduction of the specific surface area according to the phase change of Al2O3.

Sono-photo-Fenton oxidation of bisphenol-A over a LaFeO3 perovskite catalyst.

Science.gov (United States)

Dükkancı, Meral

2018-01-01

In this study, oxidation of bisphenol-A (IUPAC name - 2,2-(4,4-dihydroxyphenyl, BPA), which is an endocrine disrupting phenolic compound used in the polycarbonate plastic and epoxy resin industry, was investigated using sono-photo-Fenton process under visible light irradiation in the presence of an iron containing perovskite catalyst, LaFeO 3 . The catalyst prepared by sol-gel method, calcined at 500°C showed a catalytic activity in BPA oxidation using sono-photo-Fenton process with a degradation degree and a chemical oxygen demand (COD) reduction of 21.8% and 11.2%, respectively. Degradation of BPA was studied by using individual and combined advanced oxidation techniques including sonication, heterogeneous Fenton reaction and photo oxidation over this catalyst to understand the effect of each process on degradation of BPA. It was seen, the role of sonication was very important in hybrid sono-photo-Fenton process due to the pyrolysis and sonoluminescence effects caused by ultrasonic irradiation. The prepared LaFeO 3 perovskite catalyst was a good sonocatalyst rather than a photocatalyst. Sonication was not only the effective process to degrade BPA but also it was the cost effective process in terms of energy consumption. The studies show that the energy consumption is lower in the sono-Fenton process than those in the photo-Fenton and sono-photo- Fenton processes. Copyright © 2017 Elsevier B.V. All rights reserved.

Plasma induced degradation of benzidine in aqueous solution

International Nuclear Information System (INIS)

Gao Jinzhang; Gai Ke; Yang Wu; Dong Yanjie

2003-01-01

The degradation of benzidine in aqueous solution by the low temperature plasma was examined. The results showed that the concentration of medium and the value of pH have an appreciable effect on the degradation of benzidine. What is more important is that iron ions acting as a catalyst play an important role in this reaction. For exploring the degradation mechanism of benzidine, some of the intermediate products were recorded by HPLC (high performance liquid chromatography)

Degradation of organic pollutants by an integrated photo-Fenton-like catalysis/immersed membrane separation system

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yuanyuan, E-mail: jiedeng05@sina.com [School of Environment, Guang Xi University, Nanning 530004 (China); School of Environmental Science and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China); Xiong, Ya [School of Environmental Science and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China); Tang, Yankui; Wang, Yinghui [School of Environment, Guang Xi University, Nanning 530004 (China)

2013-01-15

Highlights: ► The photo-Fenton-like reaction and membrane separation was coupled. ► FeVO{sub 4} was used as catalyst in the PFM reactor. ► Dynamics simulation would direct the actual application of the reactor. -- Abstract: To resolve the continuously reuse problem of fine catalysts, a new reactor was investigated by coupling the heterogeneous photo-Fenton-like oxidation with membrane separation. The reactor consisted of a Xe lamp, a submerged membrane module and FeVO{sub 4} as catalyst with high activity. Results showed that the catalyst was successfully left in the reactor. It was proved by the kinetics study of membrane fouling that the avoidless membrane fouling was brought mainly by surface cake, at catalyst concentration of 4 g/L, it accounted for more than 90% of the total resistance. The kinetics study of catalytic degradation of AO II under sub-critical flux showed the optimal concentration of catalyst was 0.5 g/L and under this concentration the membrane fouling was negligible. For a residence time of 60 min, the degradation efficiency of AO II reached more than 99% and the chemical oxygen demand (COD) removal efficiency was as high as 91%. The model of continuous stirred tank reactor could predict well for the degradation which was consistent with hydrodynamics study. Moreover, the PFM reactor shows a long-term behavior with both membrane and catalyst in it and merits consideration for scaled-up trials.

Influence of generated intermediates’ interaction on heterogeneous Fenton's degradation of an azo dye 1-diazo-2-naphthol-4-sulfonic acid by using sludge based carbon as catalyst

International Nuclear Information System (INIS)

Gu, Lin; Huang, Shouqiang; Zhu, Nanwen; Zhang, Daofang; Yuan, Haiping; Lou, Ziyang

2013-01-01

Highlights: • End-products have higher tendency to be adsorbed on SC than primarily-formed. • Higher initial H 2 O 2 dosage results in intermediates with strong polarity. • 9 model intermediates differ in their behavior on interactions with catalysts. • Polar surface area dominated their adsorption on SC while K ow acts as a key role on HSC. -- Abstract: Sewage sludge based carbons have recently been used as novel catalyst in heterogeneous Fenton's reactions to degrade azo dye molecules. The carbons, functioning as both catalyst and adsorbent, play an important role in pollutants elimination, especially for those simultaneously generated organic intermediates. Different factors, i.e., H 2 O 2 concentration, may influence the type and properties of those intermediates and may have great impacts on their elimination through the interactions with catalysts’ surface. Thus, techniques including Temperature Programmed Desorption-Mass Spectrometer (TPD-MS), N 2 adsorption isotherm and Scanning Electron Microscope (SEM) were used to probe the ways of the interaction between oxidation products and catalyst by using different initial H 2 O 2 concentrations (10 and 20 mM). The higher Chemical Oxygen Demand (COD) removal with 20 mM H 2 O 2 was found to be related not only to the higher hydroxyl radicals but also the specific interactions between the intermediates and catalyst’ surface. The deep oxidation occurred in the conditions with higher oxidant amount enhances the intermediates’ adsorption on catalyst, thus increasing the COD removal by large margin. Simulated adsorption experiments by using six primarily formed intermediates and three deeply mineralized products on three different catalysts also confirmed the assumption. Results suggested close relations between adsorption capacities and intermediates’ properties such as polar surface area and octanol-water partition coefficient

Efficient degradation of phenol using iron-montmorillonite as a Fenton catalyst: Importance of visible light irradiation and intermediates

Energy Technology Data Exchange (ETDEWEB)

Wei, Xipeng; Wu, Honghai, E-mail: wuhonghai@scnu.edu.cn; He, Guangping, E-mail: hegp@scnu.edu.cn; Guan, Yufeng

2017-01-05

Highlights: • Iron-montmorillonite has excellent catalytic activity on phenol Fenton degradation. • Phenol Fenton reaction follows the two-stage pseudo first order kinetic equations. • Role of visible light irradiation is more evident during induction reaction period. • Hydroquinone and catechol have a significant effect on the second-stage kinetics. - Abstract: Iron-montmorillonite (Fe-Mt) with delaminated structures was synthesized via the introduction of iron oxides into Na-montmorillonite. Fe-Mt showed significant increases in the available iron content, surface area and pore volume, along with a slight increase in the basal spacing from d{sub 001} = 1.26 (Na-Mt) to 1.53 nm (Fe-Mt). The Fenton process was efficient for phenol removal using Fe-Mt as a catalyst under visible light irradiation, and the process had two-stage pseudo-first order kinetics. The overall reaction had a higher degradation rate even when it was only irradiated with visible light for the first 40 min period. Further investigation confirmed that the irradiation increased the presence of certain intermediates. Among them, 1,4-benzoquinone, hydroquinone, and catechol all enhanced the Fenton reaction rates. Either catechol or hydroquinone was added to the Fenton system with Fe-Mt/H{sub 2}O{sub 2} with or without visible light irradiation, and they both accelerated phenol degradation because catechol and hydroquinone are capable of reductively and effectively transforming Fe(III) into Fe(II). The concentrations of dissolved total Fe increased with the increase in the oxalic acid concentration, which can strongly chelate Fe(III). Hence, iron was released from Fe-Mt, and reductive transformation played an important role in promoting the Fenton reaction process for phenol removal.

Efficient degradation of phenol using iron-montmorillonite as a Fenton catalyst: Importance of visible light irradiation and intermediates

International Nuclear Information System (INIS)

Wei, Xipeng; Wu, Honghai; He, Guangping; Guan, Yufeng

2017-01-01

Highlights: • Iron-montmorillonite has excellent catalytic activity on phenol Fenton degradation. • Phenol Fenton reaction follows the two-stage pseudo first order kinetic equations. • Role of visible light irradiation is more evident during induction reaction period. • Hydroquinone and catechol have a significant effect on the second-stage kinetics. - Abstract: Iron-montmorillonite (Fe-Mt) with delaminated structures was synthesized via the introduction of iron oxides into Na-montmorillonite. Fe-Mt showed significant increases in the available iron content, surface area and pore volume, along with a slight increase in the basal spacing from d_0_0_1 = 1.26 (Na-Mt) to 1.53 nm (Fe-Mt). The Fenton process was efficient for phenol removal using Fe-Mt as a catalyst under visible light irradiation, and the process had two-stage pseudo-first order kinetics. The overall reaction had a higher degradation rate even when it was only irradiated with visible light for the first 40 min period. Further investigation confirmed that the irradiation increased the presence of certain intermediates. Among them, 1,4-benzoquinone, hydroquinone, and catechol all enhanced the Fenton reaction rates. Either catechol or hydroquinone was added to the Fenton system with Fe-Mt/H_2O_2 with or without visible light irradiation, and they both accelerated phenol degradation because catechol and hydroquinone are capable of reductively and effectively transforming Fe(III) into Fe(II). The concentrations of dissolved total Fe increased with the increase in the oxalic acid concentration, which can strongly chelate Fe(III). Hence, iron was released from Fe-Mt, and reductive transformation played an important role in promoting the Fenton reaction process for phenol removal.

Reduction and Analysis of Low Temperature Shift Heterogeneous Catalyst for Water Gas Reaction in Ammonia Production

Directory of Open Access Journals (Sweden)

Zečević, N.

2013-09-01

Full Text Available In order to obtain additional quantities of hydrogen after the reforming reactions of natural gas and protect the ammonia synthesis catalyst, it is crucial to achieve and maintain maximum possible activity, selectivity and stability of the low temperature shift catalyst for conversion of water gas reaction during its lifetime. Whereas the heterogeneous catalyst comes in oxidized form, it is of the utmost importance to conduct the reduction procedure properly. The proper reduction procedure and continuous analysis of its performance would ensure the required activity, selectivity and stability throughout the catalyst’s service time. For the proper reduction procedure ofthe low temperature shift catalyst, in addition to process equipment, also necessary is a reliable and realistic system for temperature measurements, which will be effective for monitoring the exothermal temperature curves through all catalyst bed layers. For efficiency evaluation of low shift temperature catalyst reduction and its optimization, it is necessary to determine at regular time intervals the temperature approach to equilibrium and temperature profiles of individual layers by means of "S" and "die off" temperature exothermal curves. Based on the obtained data, the optimum inlet temperature could be determined, in order to maximally extend the service life of the heterogeneous catalyst as much as possible, and achieve the optimum equilibrium for conversion of the water gas. This paper presents the methodology for in situ reduction of the low temperature shift heterogeneous catalyst and the developed system for monitoring its individual layers to achieve the minimum possible content of carbon monoxide at the exit of the reactor. The developed system for temperature monitoring through heterogeneous catalyst layers provides the proper procedure for reduction and adjustment of optimum process working conditions for the catalyst by the continuous increase of reactor inlet

Bacteria encapsulated in layered double hydroxides: towards an efficient bionanohybrid for pollutant degradation.

Science.gov (United States)

Halma, Matilte; Mousty, Christine; Forano, Claude; Sancelme, Martine; Besse-Hoggan, Pascale; Prevot, Vanessa

2015-02-01

A soft chemical process was successfully used to immobilize Pseudomonas sp. strain ADP (ADP), a well-known atrazine (herbicide) degrading bacterium, within a Mg2Al-layered double hydroxide host matrix. This approach is based on a simple, quick and ecofriendly direct coprecipitation of metal salts in the presence of a colloidal suspension of bacteria in water. It must be stressed that by this process the mass ratio between inorganic and biological components was easily tuned ranging from 2 to 40. This ratio strongly influenced the biological activity of the bacteria towards atrazine degradation. The better results were obtained for ratios of 10 or lower, leading to an enhanced atrazine degradation rate and percentage compared to free cells. Moreover the biohybrid material maintained this biodegradative activity after four cycles of reutilization and 3 weeks storage at 4°C. The ADP@MgAl-LDH bionanohybrid materials were completely characterized by X-ray diffraction (XRD), FTIR spectroscopy, thermogravimetric analysis and scanning and transmission electronic microscopy (SEM and TEM) evidencing the successful immobilization of ADP within the inorganic matrix. This synthetic approach could be readily extended to other microbial whole-cell immobilization of interest for new developments in biotechnological systems. Copyright © 2014 Elsevier B.V. All rights reserved.

Magnetic diatomite(Kieselguhr)/Fe2O3/TiO2 composite as an efficient photo-Fenton system for dye degradation

Science.gov (United States)

Barbosa, Isaltino A.; Zanatta, Lucas D.; Espimpolo, Daniela M.; da Silva, Douglas L.; Nascimento, Leandro F.; Zanardi, Fabrício B.; de Sousa Filho, Paulo C.; Serra, Osvaldo A.; Iamamoto, Yassuko

2017-10-01

We explored the potential use of diatomite/Fe2O3/TiO2 composites as catalysts for heterogeneous photo-Fenton degradation of methylene blue under neutral pH. Such system consists in magnetic solids synthesized by co-precipitation with Fe2+/Fe3+ in the presence of diatomite, followed by impregnation of TiO2. The results showed that the optimal amount of the catalyst was 2.0 g L-1, since aggregation phenomena become significant above this concentration, which decreases the photodegradation activity. The catalyst is highly efficient in the degradation of methylene blue and shows an easy recovery by an external magnetic field. This allows for an effective catalyst reuse without significant loss of activity in catalytic cycles, which is a highly interesting prospect for recyclable dye degradation systems.

Sabatier Catalyst Poisoning Investigation

Science.gov (United States)

Nallette, Tim; Perry, Jay; Abney, Morgan; Knox, Jim; Goldblatt, Loel

2013-01-01

The Carbon Dioxide Reduction Assembly (CRA) on the International Space Station (ISS) has been operational since 2010. The CRA uses a Sabatier reactor to produce water and methane by reaction of the metabolic CO2 scrubbed from the cabin air and the hydrogen byproduct from the water electrolysis system used for metabolic oxygen generation. Incorporating the CRA into the overall air revitalization system has facilitated life support system loop closure on the ISS reducing resupply logistics and thereby enhancing longer term missions. The CRA utilizes CO2 which has been adsorbed in a 5A molecular sieve within the Carbon Dioxide Removal Assembly, CDRA. There is a potential of compounds with molecular dimensions similar to, or less than CO2 to also be adsorbed. In this fashion trace contaminants may be concentrated within the CDRA and subsequently desorbed with the CO2 to the CRA. Currently, there is no provision to remove contaminants prior to entering the Sabatier catalyst bed. The risk associated with this is potential catalyst degradation due to trace organic contaminants in the CRA carbon dioxide feed acting as catalyst poisons. To better understand this risk, United Technologies Aerospace System (UTAS) has teamed with MSFC to investigate the impact of various trace contaminants on the CRA catalyst performance at relative ISS cabin air concentrations and at about 200/400 times of ISS concentrations, representative of the potential concentrating effect of the CDRA molecular sieve. This paper summarizes our initial assessment results.

Photocurrent Spectroscopy of Perovskite Layers and Solar Cells: A Sensitive Probe of Material Degradation

KAUST Repository

Holovský , Jakub; De Wolf, Stefaan; Werner, Jé ré mie; Remeš, Zdeněk; Mü ller, Martin; Neykova, Neda; Ledinský , Martin; Černá , Ladislava; Hrzina, Pavel; Lö per, Philipp; Niesen, Bjoern; Ballif, Christophe

2017-01-01

Optical absorptance spectroscopy of polycrystalline CHNHPbI films usually indicates the presence of a PbI phase, either as a preparation residue or due to film degradation, but gives no insight on how this may affect electrical properties. Here, we apply photocurrent spectroscopy to both perovskite solar cells and coplanar-contacted layers at various stages of degradation. In both cases, we find that the presence of a PbI phase restricts charge-carrier transport, suggesting that PbI encapsulates CHNHPbI grains. We also find that PbI injects holes into the CHNHPbI grains, increasing the apparent photosensitivity of PbI. This phenomenon, known as modulation doping, is absent in the photocurrent spectra of solar cells, where holes and electrons have to be collected in pairs. This interpretation provides insights into the photogeneration and carrier transport in dual-phase perovskites.

Photocurrent Spectroscopy of Perovskite Layers and Solar Cells: A Sensitive Probe of Material Degradation

KAUST Repository

Holovský, Jakub

2017-01-25

Optical absorptance spectroscopy of polycrystalline CHNHPbI films usually indicates the presence of a PbI phase, either as a preparation residue or due to film degradation, but gives no insight on how this may affect electrical properties. Here, we apply photocurrent spectroscopy to both perovskite solar cells and coplanar-contacted layers at various stages of degradation. In both cases, we find that the presence of a PbI phase restricts charge-carrier transport, suggesting that PbI encapsulates CHNHPbI grains. We also find that PbI injects holes into the CHNHPbI grains, increasing the apparent photosensitivity of PbI. This phenomenon, known as modulation doping, is absent in the photocurrent spectra of solar cells, where holes and electrons have to be collected in pairs. This interpretation provides insights into the photogeneration and carrier transport in dual-phase perovskites.

The kinetics of steam-carbon dioxide conversion, rational ways and production catalysts of process gas

International Nuclear Information System (INIS)

Khamroev, F.B.

2016-01-01

The purpose of the present work is to study the kinetics of steam-carbon dioxide conversion, rational ways and production catalysts of process gas. The experimental equation of steam-carbon methane conversion, heat stability increasing and catalyst efficiency, decreasing of hydrodynamical resistance of catalyst layer were determined.

Fast degradation of dyes in water using manganese-oxide-coated diatomite for environmental remediation

Science.gov (United States)

Dang, Trung-Dung; Banerjee, Arghya Narayan; Tran, Quang-Tung; Roy, Sudipta

2016-11-01

By a simple wet-chemical procedure using a permanganate in the acidic medium, diatomite coated with amorphous manganese oxide nanoparticles was synthesized. The structural, microstructural and morphological characterizations of the as-synthesized catalysts confirmed the nanostructure of MnO2 and its stabilization on the support - diatomite. The highly efficient and rapid degradation of methylene blue and methyl orange over synthesized MnO2 coated Diatomite has been carried out. The results revealed considerably faster degradation of the dyes against the previously reported data. The proposed mechanism of the dye-degradation is considered to be a combinatorial effect of chemical, physicochemical and physical processes. Therefore, the fabricated catalysts have potential application in waste water treatment, and pollution degradation for environmental remediation.

A durable PtRu/C catalyst with a thin protective layer for direct methanol fuel cells.

Science.gov (United States)

Shimazaki, Yuzuru; Hayasaka, Sho; Koyama, Tsubasa; Nagao, Daisuke; Kobayashi, Yoshio; Konno, Mikio

2010-11-15

A methanol oxidation catalyst with improved durability in acidic environments is reported. The catalyst consists of PtRu alloy nanoparticles on a carbon support that were stabilized with a silane-coupling agent. The catalyst was prepared by reducing ions of Pt and Ru in the presence of a carbon support and the silane-coupling agent. The careful choice of preparatory conditions such as the concentration of the silane-coupling agent and solution pH resulted in the preparation of catalyst in which the PtRu nanoparticles were dispersively adsorbed onto the carbon support. The catalytic activity was similar to that of a commercial catalyst and was unchanged after immersion in sulfuric acid solution for 1000 h, suggesting the high durability of the PtRu catalyst for the anode of direct methanol fuel cells. Copyright © 2010 Elsevier Inc. All rights reserved.

Preparation of catalyst coated membrane by modified decal transfer method for proton exchange membrane fuel cell

Science.gov (United States)

Indriyati; Irmawati, Y.; Prihandoko, B.

2017-07-01

A new catalyst coated membrane (CCM) was prepared by modified decal transfer method. A structure of ionomer/catalyst/carbon/substrate was used to facilitate the transfer of catalyst layer from decal substrate to the membrane at quite low hot-pressing temperature (120 °C) for 8 min. Several decal substrates were tested to select a proper substrate, namely PTFE cloth, PTFE film, aluminium foil, and OHP transparent sheet. The transfer degree of catalyst layer was estimated. Elemental analysis and SEM-mapping were performed to evaluate the residue, whereas contact angle measurement was conducted to characterize the hydrophobicity of decal substrates. The results showed that PTFE cloth and PFTE film transferred approximately 90% of catalyst layer onto the membrane, while the other two substrates were around 70%. Furthermore, the elemental analysis of the residue on the substrate revealed that it was mainly composed of carbon and fluorine for PTFE cloth and PTFE film. This result supports other findings that PTFE cloth and PTFE film are suitable as decal substrate at low temperature hot pressing for fabricating CCM.

Synthesis of Cu/TiO{sub 2}/organo-attapulgite fiber nanocomposite and its photocatalytic activity for degradation of acetone in air

Energy Technology Data Exchange (ETDEWEB)

Zhang, Gaoke, E-mail: gkzhang@whut.edu.cn; Wang, He; Guo, Sheng; Wang, Junting; Liu, Jin

2016-01-30

Graphical abstract: - Highlights: • A novel Cu/TiO{sub 2}/organo-attapulgite fiber nanocomposite was synthesized successfully. • Micro-mesopore nanocomposite structure was in favor of the degradation of acetone. • CTAB modification improved the adsorption capability of the catalyst. • The photocatalytic degradation mechanism of the acetone by the catalyst was studied. - Abstract: The Cu/TiO{sub 2}/organo-attapulgite fiber (CTOA) nanocomposite was synthesized by a facile method and was used for photocatalytic degradation of acetone in air under UV light irradiation. The as-prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscope (SEM), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectrum (UV–vis DRS), inductively coupled plasma (ICP) spectrometry and N{sub 2} adsorption–desorption measurement. The results showed that the structure of organo-attapulgite (OAT) had no obvious change as compared to unmodified attapulgite (AT) and the attapulgite fibers in the OAT were well-dispersed. Both micropores and mesopores exist in the CTOA catalyst. The CTOA catalysts prepared at the Cu/TiO{sub 2} molar ratio of 0.003 shows an excellent photocatalytic activity for the degradation of acetone in air. The synergistic effect of Cu species and cetyltrimethylammonium bromide modification can be responsible for the enhanced photocatalytic activity of the CTOA catalyst. The mechanism of the photocatalytic degradation of acetone by the CTOA catalyst was discussed.

Enhanced photocatalytic activity of ZnO/CuO nanocomposite for the degradation of textile dye on visible light illumination

International Nuclear Information System (INIS)

Saravanan, R.; Karthikeyan, S.; Gupta, V.K.; Sekaran, G.; Narayanan, V.; Stephen, A.

2013-01-01

The photocatalytic degradation of organic dyes such as methylene blue and methyl orange in the presence of various percentages of composite catalyst under visible light irradiation was carried out. The catalyst ZnO nanorods and ZnO/CuO nanocomposites of different weight ratios were prepared by new thermal decomposition method, which is simple and cost effective. The prepared catalysts were characterized by different techniques such as X-ray diffraction, transmission electron microscopy, field emission scanning electron microscopy, Fourier transform infrared spectroscopy and UV–visible absorption spectroscopy. Further, the most photocatalytically active composite material was used for degradation of real textile waste water under visible light illumination. The irradiated samples were analysed by total organic carbon and chemical oxygen demand. The efficiency of the catalyst and their photocatalytic mechanism has been discussed in detail. Highlights: ► Visible light active photocatalyst ► Degradation of methylene blue and methyl orange ► Preparation of composite materials is a simple, fast and cost effective method. ► Nano composite materials ► Degradation of textile waste water

Nano-Engineered Catalysts for Direct Methanol Fuel Cells

Science.gov (United States)

Myung, Nosang; Narayanan, Sekharipuram; Wiberg, Dean

2008-01-01

Nano-engineered catalysts, and a method of fabricating them, have been developed in a continuing effort to improve the performances of direct methanol fuel cells as candidate power sources to supplant primary and secondary batteries in a variety of portable electronic products. In order to realize the potential for high energy densities (as much as 1.5 W h/g) of direct methanol fuel cells, it will be necessary to optimize the chemical compositions and geometric configurations of catalyst layers and electrode structures. High performance can be achieved when catalyst particles and electrode structures have the necessary small feature sizes (typically of the order of nanometers), large surface areas, optimal metal compositions, high porosity, and hydrophobicity. The present method involves electrodeposition of one or more catalytic metal(s) or a catalytic-metal/polytetrafluoroethylene nanocomposite on an alumina nanotemplate. The alumina nanotemplate is then dissolved, leaving the desired metal or metal/polytetrafluoroethylene-composite catalyst layer. Unlike some prior methods of making fine metal catalysts, this method does not involve processing at elevated temperature; all processing can be done at room temperature. In addition, this method involves fewer steps and is more amenable to scaling up for mass production. Alumina nanotemplates are porous alumina membranes that have been fabricated, variously, by anodizing either pure aluminum or aluminum that has been deposited on silicon by electronbeam evaporation. The diameters of the pores (7 to 300 nm), areal densities of pores (as much as 7 x 10(exp 10)sq cm), and lengths of pores (up to about 100 nm) can be tailored by selection of fabrication conditions. In a given case, the catalytic metal, catalytic metal alloy, or catalytic metal/ polytetrafluoroethylene composite is electrodeposited in the pores of the alumina nanotemplate. The dimensions of the pores, together with the electrodeposition conditions

Nanobiocatalytic Degradation of Acid Orange 7

Science.gov (United States)

Hastings, Jason

The catalytic properties of various metal nanoparticles have led to their use in environmental remediation applications. However, these remediation strategies are limited by their ability to deliver catalytic nanoparticles and a suitable electron donor to large treatment zones. Clostridium pasteurianum BC1 cells, loaded with bio-Pd nanoparticles, were used to effectively catalyze the reductive degradation and removal of Acid Orange 7 (AO7), a model azo compound. Hydrogen produced fermentatively by the C. pasteurianum BC1 acted as the electron donor for the process. Pd-free bacterial cultures or control experiments conducted with heat-killed cells showed limited reduction of AO7. Experiments also showed that the in situ biological production of H2 by C. pasteurianum BC1 was essential for the degradation of AO7, which suggests a novel process where the in situ microbial production of hydrogen is directly coupled to the catalytic bio-Pd mediated reduction of AO7. The differences in initial degradation rate for experiments conducted using catalyst concentrations of 1ppm Pd and 5ppm Pd and an azo dye concentration of 100ppm AO7 was 0.39 /hr and 1.94 /hr respectively, demonstrating the importance of higher concentrations of active Pd(0). The degradation of AO7 was quick as demonstrated by complete reductive degradation of 50ppm AO7 in 2 hours in experiments conducted using a catalyst concentration of 5ppm Pd. Dye degradation products were analyzed via Gas Chromatograph-Mass Spectrometer (GCMS), High Performance Liquid Chromatography (HPLC), UltraViolet-Visible spectrophotometer (UV-Vis) and Matrix-Assisted Laser Desorption/Ionization (MALDI) spectrometry. The presence of 1-amino 2-naphthol, one of the hypothesized degradation products, was confirmed using mass spectrometry.

Adsorption and bio-sorption of nickel ions and reuse for 2-chlorophenol catalytic ozonation oxidation degradation from water

International Nuclear Information System (INIS)

Ma, Wei; Zong, Panpan; Cheng, Zihong; Wang, Baodong; Sun, Qi

2014-01-01

Highlights: • Biomass and fly ash which were widespread for adsorption of heavy metal ions. • Preparation of catalyst by saturated adsorbents for 2-chlorophenol ozone degradation. • This work demonstrated that the O 3 /catalyst process was an effective pathway. • The use of nickel ions, fly ash and sawdust to achieve the recycling utilization of resources. -- Abstract: This work explored the preparation of an effective and low-cost catalyst and investigated its catalytic capacity for 2-chlorophenol ozonation oxidation degradation in wastewater by using an ozone oxidation batch reactor. The catalyst was directly prepared by the reuse of fly ash and sawdust after saturated adsorption of nickel ions from wastewater, which was proposed as an efficient and economic approach. The obtained catalyst was characterized by TGA, BET, FTIR, XRD, and SEM, the results showed that fly ash as the basic framework has high specific surface area and the addition of sawdust as the porogen agent could improve the pore structure of the catalyst. The adsorption of nickel ions by fly ash and sawdust from aqueous solution was also investigated in this study. The results obtained from the experiments indicated that adsorption of nickel ions by fly ash and biomass sawdust could be well described by Langmuir isotherm model and pseudo second order kinetic model. The catalytic performance of catalyst was studied in terms of the effect of time, liquid–solid ratio and pH on 2-chlorophenol ozonation degradation. It was found that the catalyst could effectively improve the ozonation reaction rate at pH = 7 with a 2:1 liquid–solid ratio. The kinetic study demonstrated that the reaction followed the first order model, and the rate constant increased 267% (0.03–0.1 min −1 ) of 2-chlorophenol ozonation degradation with 5 mmol/L concentration at pH = 7.0 compared with ozonation alone

Atomic layer deposition of ruthenium surface-coating on porous platinum catalysts for high-performance direct ethanol solid oxide fuel cells

Science.gov (United States)

Jeong, Heon Jae; Kim, Jun Woo; Jang, Dong Young; Shim, Joon Hyung

2015-09-01

Pt-Ru bi-metallic catalysts are synthesized by atomic layer deposition (ALD) of Ru surface-coating on sputtered Pt mesh. The catalysts are evaluated in direct ethanol solid oxide fuel cells (DESOFCs) in the temperature range of 300-500 °C. Island-growth of the ALD Ru coating is confirmed by transmission electron microscopy and X-ray photoelectron spectroscopy (XPS) analyses. The performance of the DESOFCs is evaluated based on the current-voltage output and electrochemical impedance spectroscopy. Genuine reduction of the polarization impedance, and enhanced power output with improved surface kinetics are achieved with the optimized ALD Ru surface-coating compared to bare Pt. The chemical composition of the Pt/ALD Ru electrode surface after fuel cell operation is analyzed via XPS. Enhanced cell performance is clearly achieved, attributed to the effective Pt/ALD Ru bi-metallic catalysis, including oxidation of Cdbnd O by Ru, and de-protonation of ethanol and cleavage of C-C bonds by Pt, as supported by surface morphology analysis which confirms formation of a large amount of carbon on bare Pt after the ethanol-fuel-cell test.

Degradation mechanisms in organic photovoltaic devices

NARCIS (Netherlands)

Grossiord, Nadia; Kroon, Jan M.; Andriessen, Ronn; Blom, Paul W. M.

In the present review, the main degradation mechanisms occurring in the different layer stacking (i.e. photoactive layer, electrode, encapsulation film, interconnection) of polymeric organic solar cells and modules are discussed. Bulk and interfacial, as well as chemical and physical degradation

Catalytic ozonation of oxalate with a cerium supported palladium oxide: An efficient degradation not relying on hydroxyl radical oxidation

KAUST Repository

Zhang, Tao; Li, Weiwei; Croue, Jean-Philippe

2011-01-01

The cerium supported palladium oxide (PdO/CeO 2) at a low palladium loading was found very effective in catalytic ozonation of oxalate, a probe compound that is difficult to be efficiently degraded in water with hydroxyl radical oxidation and one of the major byproducts in ozonation of organic matter. The oxalate was degraded into CO 2 during the catalytic ozonation. The molar ratio of oxalate degraded to ozone consumption increased with increasing catalyst dose and decreasing ozone dosage and pH under the conditions of this study. The maximum molar ratio reached around 1, meaning that the catalyst was highly active and selective for oxalate degradation in water. The catalytic ozonation, which showed relatively stable activity, does not promote hydroxyl radical generation from ozone. Analysis with ATR-FTIR and in situ Raman spectroscopy revealed that 1) oxalate was adsorbed on CeO 2 of the catalyst forming surface complexes, and 2) O 3 was adsorbed on PdO of the catalyst and further decomposed to surface atomic oxygen (*O), surface peroxide (*O 2), and O 2 gas in sequence. The results indicate that the high activity of the catalyst is related to the synergetic function of PdO and CeO 2 in that the surface atomic oxygen readily reacts with the surface cerium-oxalate complex. This kind of catalytic ozonation would be potentially effective for the degradation of polar refractory organic pollutants and hydrophilic natural organic matter. © 2011 American Chemical Society.

Catalytic ozonation of oxalate with a cerium supported palladium oxide: An efficient degradation not relying on hydroxyl radical oxidation

KAUST Repository

Zhang, Tao

2011-11-01

The cerium supported palladium oxide (PdO/CeO 2) at a low palladium loading was found very effective in catalytic ozonation of oxalate, a probe compound that is difficult to be efficiently degraded in water with hydroxyl radical oxidation and one of the major byproducts in ozonation of organic matter. The oxalate was degraded into CO 2 during the catalytic ozonation. The molar ratio of oxalate degraded to ozone consumption increased with increasing catalyst dose and decreasing ozone dosage and pH under the conditions of this study. The maximum molar ratio reached around 1, meaning that the catalyst was highly active and selective for oxalate degradation in water. The catalytic ozonation, which showed relatively stable activity, does not promote hydroxyl radical generation from ozone. Analysis with ATR-FTIR and in situ Raman spectroscopy revealed that 1) oxalate was adsorbed on CeO 2 of the catalyst forming surface complexes, and 2) O 3 was adsorbed on PdO of the catalyst and further decomposed to surface atomic oxygen (*O), surface peroxide (*O 2), and O 2 gas in sequence. The results indicate that the high activity of the catalyst is related to the synergetic function of PdO and CeO 2 in that the surface atomic oxygen readily reacts with the surface cerium-oxalate complex. This kind of catalytic ozonation would be potentially effective for the degradation of polar refractory organic pollutants and hydrophilic natural organic matter. © 2011 American Chemical Society.

Low cost fuel cell diffusion layer configured for optimized anode water management

Science.gov (United States)

Owejan, Jon P; Nicotera, Paul D; Mench, Matthew M; Evans, Robert E

2013-08-27

A fuel cell comprises a cathode gas diffusion layer, a cathode catalyst layer, an anode gas diffusion layer, an anode catalyst layer and an electrolyte. The diffusion resistance of the anode gas diffusion layer when operated with anode fuel is higher than the diffusion resistance of the cathode gas diffusion layer. The anode gas diffusion layer may comprise filler particles having in-plane platelet geometries and be made of lower cost materials and manufacturing processes than currently available commercial carbon fiber substrates. The diffusion resistance difference between the anode gas diffusion layer and the cathode gas diffusion layer may allow for passive water balance control.

Interplay of Interfacial Layers and Blend Composition To Reduce Thermal Degradation of Polymer Solar Cells at High Temperature.

Science.gov (United States)

Ben Dkhil, Sadok; Pfannmöller, Martin; Schröder, Rasmus R; Alkarsifi, Riva; Gaceur, Meriem; Köntges, Wolfgang; Heidari, Hamed; Bals, Sara; Margeat, Olivier; Ackermann, Jörg; Videlot-Ackermann, Christine

2018-01-31

The thermal stability of printed polymer solar cells at elevated temperatures needs to be improved to achieve high-throughput fabrication including annealing steps as well as long-term stability. During device processing, thermal annealing impacts both the organic photoactive layer, and the two interfacial layers make detailed studies of degradation mechanism delicate. A recently identified thermally stable poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b']dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl

Nanostructured Co3O4 grown on nickel foam: An efficient and readily recyclable 3D catalyst for heterogeneous peroxymonosulfate activation.

Science.gov (United States)

Yuan, Ruixia; Hu, Lin; Yu, Peng; Wang, Huaiyuan; Wang, Zhaohui; Fang, Jingyun

2018-05-01

Cobalt-based heterogeneous catalyst has been recognized as one of most efficient activators for peroxymonosulfate (PMS) decomposition, but usually suffers from the poor stability and difficulty to recover and reuse. Here easily recyclable cobalt oxide (Co 3 O 4 ) nanowires and nanoflowers grown on nickel foam (NF) are fabricated by a hydrothermal and calcination method. The prepared 3D Co 3 O 4 /NF catalyst is characterized and applied as a heterogeneous catalyst for PMS activation to generate sulfate radicals for decomposition of Acid Orange 7 (AO7). The results show that the AO7 degradation rate increases with cobalt loading and PMS dosage, but decreases with the increase of solution pH. The Co 3 O 4 /NF catalyst using 2 mM Co(NO 3 ) 2 ·6H 2 O as cobalt source exhibits highest activity, and almost complete decolorization could be achieved within 30 min. The diverse effects of coexisting anions (SO 4 2- , HCO 3 - , NO 3 - and Cl - ) on AO7 degradation are observed and explained. After 10 consecutive runs, excellent catalytic reactivity of the catalyst remains while the level of leached cobalt during the catalyst usage is much lower than the maximum allowable concentration in drinking and natural water. More importantly, the macroscopic Co 3 O 4 /NF catalyst shows advantage of easy recycling after application compared to traditional catalysts. It is believed that the as-prepared Co 3 O 4 /NF is promising to be an effective and green heterogeneous catalyst for PMS activation to degrade organic pollutants for environmental application. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ultrasonic Degradation of Fuchsin Basic in Aqueous Solution: Effects of Operating Parameters and Additives

Directory of Open Access Journals (Sweden)

Rui-Jia Lan

2013-01-01

Full Text Available Ultrasonic degradation is one of the recent advanced oxidation processes (AOPs and proven to be effective for removing low-concentration organic pollutants from aqueous solutions. In this study, removal of fuchsin basic from aqueous solutions by ultrasound was investigated. The effects of operating parameters such as ultrasound power (200 W–500 W, initial pH (3–6.5, and temperature (15, 22, 35, and 60°C on the ultrasonic degradation were studied. The degradation of fuchsin under ultrasound irradiation basic was found to obey pseudo first-order reaction kinetics. Addition of catalyst Fe(II had a markedly positive effect on degradation. 84.1% extent of degradation was achieved at initial dye concentration 10 μmol L−1, ultrasound power 400 W, ultrasound frequency 25 kHz, dosage of Fe(II 4 mg L−1, initial pH 6.5, and temperature 22°C. But addition of heterogeneous catalyst TiO2 affected degradation slightly. Addition of radical scavenger suppressed fuchsin basic degradation significantly.

Scaling of Polymer Degradation Rate within a High-Reynolds-Number Turbulent Boundary Layer

Science.gov (United States)

Elbing, Brian; Solomon, Michael; Perlin, Marc; Dowling, David; Ceccio, Steven

2009-11-01

An experiment conducted at the U.S. Navy's Large Cavitation Channel on a 12.9 m long flat-plate test model produced the first quantitative measurements of polymer molecular weight within a turbulent boundary layer. Testing was conducted at speeds to 20 m/s and downstream distance based Reynolds numbers to 220 million. These results showed that the rate of polymer degradation by scission of the polymer chains increases with increased speed, downstream distance and surface roughness. With the surface fully rough at 20 m/s there was no measureable level of drag reduction at the first measurement location (0.56 m downstream of injection). These results are scaled with the assumption that the rate of degradation is dependent on the polymer residence time in the flow and the local shear rate. A successful collapse of the data within the measurement uncertainty was achieved over a range of flow speed (6.6 to 20 m/s), surface roughness (smooth and fully rough) and downstream distance from injection (0.56 to 9.28 m).

Influence of generated intermediates’ interaction on heterogeneous Fenton's degradation of an azo dye 1-diazo-2-naphthol-4-sulfonic acid by using sludge based carbon as catalyst

Energy Technology Data Exchange (ETDEWEB)

Gu, Lin [School of Environment and Architecture, University of Shanghai for Science and Technology, Shanghai 200093 (China); School of Environmental Science and Technology, Shanghai Jiao Tong University, Shanghai 200240 (China); Huang, Shouqiang [School of Environmental Science and Technology, Shanghai Jiao Tong University, Shanghai 200240 (China); Zhu, Nanwen, E-mail: nwzhu@sjtu.edu.cn [School of Environmental Science and Technology, Shanghai Jiao Tong University, Shanghai 200240 (China); Zhang, Daofang, E-mail: Zhangdf-usst@163.com [School of Environment and Architecture, University of Shanghai for Science and Technology, Shanghai 200093 (China); Yuan, Haiping; Lou, Ziyang [School of Environmental Science and Technology, Shanghai Jiao Tong University, Shanghai 200240 (China)

2013-12-15

Highlights: • End-products have higher tendency to be adsorbed on SC than primarily-formed. • Higher initial H{sub 2}O{sub 2} dosage results in intermediates with strong polarity. • 9 model intermediates differ in their behavior on interactions with catalysts. • Polar surface area dominated their adsorption on SC while K{sub ow} acts as a key role on HSC. -- Abstract: Sewage sludge based carbons have recently been used as novel catalyst in heterogeneous Fenton's reactions to degrade azo dye molecules. The carbons, functioning as both catalyst and adsorbent, play an important role in pollutants elimination, especially for those simultaneously generated organic intermediates. Different factors, i.e., H{sub 2}O{sub 2} concentration, may influence the type and properties of those intermediates and may have great impacts on their elimination through the interactions with catalysts’ surface. Thus, techniques including Temperature Programmed Desorption-Mass Spectrometer (TPD-MS), N{sub 2} adsorption isotherm and Scanning Electron Microscope (SEM) were used to probe the ways of the interaction between oxidation products and catalyst by using different initial H{sub 2}O{sub 2} concentrations (10 and 20 mM). The higher Chemical Oxygen Demand (COD) removal with 20 mM H{sub 2}O{sub 2} was found to be related not only to the higher hydroxyl radicals but also the specific interactions between the intermediates and catalyst’ surface. The deep oxidation occurred in the conditions with higher oxidant amount enhances the intermediates’ adsorption on catalyst, thus increasing the COD removal by large margin. Simulated adsorption experiments by using six primarily formed intermediates and three deeply mineralized products on three different catalysts also confirmed the assumption. Results suggested close relations between adsorption capacities and intermediates’ properties such as polar surface area and octanol-water partition coefficient.

Electrocatalytic activity of atomic layer deposited Pt–Ru catalysts onto N-doped carbon nanotubes

DEFF Research Database (Denmark)

Johansson, Anne-Charlotte Elisabeth Birgitta; Larsen, Jackie Vincent; Verheijen, Marcel A.

2014-01-01

(ethylcyclopentadienyl)ruthenium (Ru(EtCp)2), respectively. O2 was used as the reactant in both processes. The composition of the catalysts was easily tuned by varying the Pt-to-Ru ALD cycle ratio. The catalysts were tested toward the CO oxidation and methanol oxidation reaction (MOR) in a three-electrode electrochemical set...

Role of active species on photocatalytic degradation of remazol golden yellow textile dye employing SrSnO_3 or TiO_2 as catalyst

International Nuclear Information System (INIS)

Teixeira, Ana Rita Ferreira Alves

2015-01-01

Heterogeneous photocatalysis is an important alternative for environmental remediation, with the possibility of its use for degradation of textile dyes effluents, as remazol golden yellow (RNL). Many semiconductors can be employed as photocatalysts, highlighting commercial TiO_2 P25 Evonik, a mixture of anatase and rutile phases. Other materials have been studied for such application, including SrSnO_3. In this work, strontium stannate was synthesized by the modified Pechini method and its photocatalytic activity on the degradation of the RNL textile was evaluated, as well as the activity for the commercial P25. The aim of this study was determining the role of each active specie on the photodegradation of the RNL system. In order to achieve such objective, some experiments were carried out in the presence of hydroxyl radical, hole and electron scavengers (isopropanol, formic acid and silver, respectively). The photocatalysts were characterized by X-ray diffraction (XDR), infrared spectroscopy (IV), Raman spectroscopy, UV-visible spectroscopy, surface area by BET method, and zero charge potential. SrSnO_3 obtained showed strontium carbonate as secondary phase, and this may have caused a short-range disorder for the material. The photocatalytic performance was evaluated by UV-Vis spectroscopy analysis of the RNL solutions before and after UVC irradiation in the presence of catalysts. The use of scavengers showed that, for both catalysts, hydroxyl radical play a major role, holes have an important participation on the formation of these radicals while electrons have no considerable participation. The results confirm that recombination is a limiting factor for SrSnO_3 and P25. (author)

Nitrogen–doped graphitized carbon shell encapsulated NiFe nanoparticles: A highly durable oxygen evolution catalyst

Energy Technology Data Exchange (ETDEWEB)

Du, Lei; Luo, Langli; Feng, Zhenxing; Engelhard, Mark; Xie, Xiaohong; Han, Binghong; Sun, Junming; Zhang, Jianghao; Yin, Geping; Wang, Chongmin; Wang, Yong; Shao, Yuyan

2017-09-01

Oxygen evolution reaction (OER) plays a crucial role in various energy conversion devices such as water electrolyzers and metal–air batteries. Precious metal catalysts such as Ir, Ru and their oxides are usually used for enhanced reaction kinetics but are limited by their scarce resource. The challenges associated with alternative non–precious metal catalysts such as transition metal oxides and (oxy)hydroxides etc. are their low electronic conductivity and poor durability. Here, we report OER catalysts of NiFe nanoparticles encapsulated by nitrogen–doped graphitized carbon shells derived from bimetallic metal–organic frameworks (MOFs) precursors. The optimal OER catalyst shows excellent activity (360 mV overpotential at 10 mA cm–2GEO) and durability (no obvious degradation after 20 000 cycles). The electron-donation from Fe and tuned electronic structure of metal cores by Ni are revealed to be primary contributors to the enhanced OER activity. We further demonstrated that the structure and morphology of encapsulating carbon shells, which are the key factors influencing the durability, are facilely controlled by chemical state of precursors. Severe metal particle growth probably caused by oxidation of carbon shells and encapsulated nanoparticles is believed to the main mechanism for activity degradation in these catalysts.

Photocatalytic hydrogen production on SOLECTRO {sup registered} titanium dioxide layers. Development and characterization of an efficient catalyst; Photokatalytische Wasserstoffgewinnung an SOLECTRO {sup registered} -Titandioxidschichten. Entwicklung und Charakterisierung eines geeigneten Katalysators

Energy Technology Data Exchange (ETDEWEB)

Saborowski, Sarah

2010-03-03

A catalyst for photocatalytic hydrogen production from methanol and water was developed on the basis of SOLECTRO {sup registered} titanium dioxide layers. A test facility was constructed in which several modified catalysts could be tested for this reaction. Detailed characterization of the electronic and optical characteristics of these catalysts made it possible to gain deeper insight into the processes involved in the reaction. (orig.) [German] Auf Basis der SOLECTRO {sup registered} -TiO{sub 2} -Schichten wurde ein Katalysator fuer die photokatalytische Wasserstoffdarstellung aus Methanol und Wasser entwickelt. Der Aufbau einer geeigneten Versuchsanlage ermoeglichte es, verschieden modifizierte Katalysatoren fuer diese Reaktion zu testen. Durch die ausfuehrliche Charakterisierung insbesondere der elektronischen und optischen Eigenschaften dieser Katalysatoren konnten vertiefende Erkenntnisse zu den waehrend der Reaktion ablaufenden Prozessen gewonnen werden. (orig.)

Selective hydrogenation of 1,3-butadiene from crude C{sub 4} cracker stream with a solid catalyst with ionic liquid layer (SCILL). DSC and solubility study

Energy Technology Data Exchange (ETDEWEB)

Mangartz, T.; Korth, W.; Kern, C.; Jess, A. [Bayreuth Univ. (Germany). Dept. of Chemical Engineering

2013-11-01

In petroleum as well as in fine chemical industry, selective catalytic hydrogenation is an important reaction. The selective hydrogenation of 1,3-butadiene (BD) to butene (trans-,1- and cis-butene) from the crude C4 steam cracker fraction represents one example, but under today's technical conditions undesired butane forms inevitably in relevant amounts. To increase the butene yield, the concept of Solid Catalyst with Ionic Liquid Layer (SCILL) was employed. The SCILL catalyst, in contrast to the uncoated catalyst, yielded a remarkably high selectivity to butenes (S{sub butenes} > 99 %) even at high residence times or at high hydrogen partial pressure. Nearly no butane (S{sub butane} {approx} 0 %) was analytically detected. We expected that due to different solubility, the poorer soluble compounds discharged from the ionic liquid and, thus, caused the shift in selectivity to a great extent. Temperature dependent solubility measurements in the used ionic liquid ([DMIM][DMP]) revealed that the order of increasing solubility is 1,3-butadiene > butenes > butane which matches the assumption. However, since differences in solubility cannot explain this SCILL effect satisfyingly, ionic liquids are expected to affect the surface of the catalyst (side-specific ligand-type effect). Investigations using spectroscopic methods (e.g. FTIR) confirmed this suggestion. (orig.)

Synthesis of SnO{sub 2}-activated carbon fiber hybrid catalyst for the removal of methyl violet from water

Energy Technology Data Exchange (ETDEWEB)

Li, Jia, E-mail: mse_lij@ujn.edu.cn [School of Material Science and Engineering, University of Jinan, Jinan 250022 (China); Ng, Dickon H.L. [Department of Physics, The Chinese University of Hong Kong, Shatin, Hong Kong (China); Song, Peng; Kong, Chao; Song, Yi [School of Material Science and Engineering, University of Jinan, Jinan 250022 (China)

2015-04-15

Graphical abstract: - Highlights: • A new biomass route for the synthesis of SnO{sub 2}/ACF hybrid catalyst was proposed. • The original fibrous structure of kapok fiber was retained in the SnO{sub 2}/ACF hybrid catalyst. • SnO{sub 2}/ACF hybrid catalyst exhibited high BET surface area (647–897 m{sup 2}/g) and large pore volume (0.36–0.56 cm{sup 3} g{sup −1}). • High microwave-induced catalytic activity for methyl violet degradation was obtained. - Abstract: SnO{sub 2}/activated carbon fiber (ACF) hybrid catalyst was synthesized from kapok precursor via a two-step process involving pore-fabricating and self-assembly of SnO{sub 2} nanoparticles. The morphology and phase structure of the obtained samples were characterized by X-ray diffraction, field emission scanning electron microscope, high resolution transmission electron microscopy and N{sub 2} adsorption-desorption isotherm. These results demonstrated that the synthesized SnO{sub 2}/ACF retained the hollow-fiber structure of kapok fibers. SnO{sub 2} nanoparticles dispersed uniformly over the ACF support. The obtained hybrid catalyst showed porous structure with high surface area (647–897 m{sup 2}/g) and large pore volume (0.36–0.56 cm{sup 3} g{sup −1}). In addition, the catalytic activities of the obtained samples for methyl violet degradation under microwave irradiation were also evaluated. It was found that the SnO{sub 2}/ACF catalyst exhibited high catalytic activity for methyl violet degradation due to the synergistic effect of microwave and SnO{sub 2}/ACF catalyst.

Oxidative degradation stability and hydrogen sulfide removal performance of dual-ligand iron chelate of Fe-EDTA/CA.

Science.gov (United States)

Miao, Xinmei; Ma, Yiwen; Chen, Zezhi; Gong, Huijuan

2017-09-05

Catalytic oxidation desulfurization using chelated iron catalyst is an effective method to remove H 2 S from various gas streams including biogas. However, the ligand of ethylenediaminetetraacetic acid (EDTA), which is usually adopted to prepare chelated iron catalyst, is liable to be oxidative degraded, and leads to the loss of desulfurization performance. In order to improve the degradation stability of the iron chelate, a series of iron chelates composed of two ligands including citric acid (CA) and EDTA were prepared and the oxidative degradation stability as well as desulfurization performance of these chelated iron catalysts were studied. Results show that the iron chelate of Fe-CA is more stable than Fe-EDTA, while for the desulfurization performance, the situation is converse. For the dual-ligand iron chelates of Fe-EDTA/CA, with the increase of mol ratio of CA to EDTA in the iron chelate solution, the oxidative degradation stability increased while the desulfurization performance decreased. The results of this work showed that Fe-EDTA/CA with a mol ratio of CA:EDTA = 1:1 presents a relative high oxidative degradation stability and an acceptable desulfurization performance with over 90% of H 2 S removal efficiency.

Methanol-Tolerant Cathode Catalyst Composite For Direct Methanol Fuel Cells

Science.gov (United States)

Zhu, Yimin; Zelenay, Piotr

2006-03-21

A direct methanol fuel cell (DMFC) having a methanol fuel supply, oxidant supply, and its membrane electrode assembly (MEA) formed of an anode electrode and a cathode electrode with a membrane therebetween, a methanol oxidation catalyst adjacent the anode electrode and the membrane, an oxidant reduction catalyst adjacent the cathode electrode and the membrane, comprises an oxidant reduction catalyst layer of a platinum-chromium alloy so that oxidation at the cathode of methanol that crosses from the anode through the membrane to the cathode is reduced with a concomitant increase of net electrical potential at the cathode electrode.

Degradation of 2,4,6-trichlorophenol with peroxymonosulfate catalyzed by soluble and supported iron porphyrins

International Nuclear Information System (INIS)

Günay, Tuğçe; Çimen, Yasemin

2017-01-01

Degradation of 2,4,6-trichloropenol (TCP) with peroxymonosulfate (PMS) catalyzed by iron porphyrin tetrasulfonate ([FePTS)] was investigated in an 8-to-1 (v/v) CH 3 OH-H 2 O mixture. Typical reaction medium contained a 4.00 mL methanol solution of TCP (0.100 mmol), a 0.50 mL aqueous solution of catalyst (5.0 × 10 −4  mmol), and 0.100 mmol PMS (as 0.031 g of Oxone). The reaction was performed at ambient temperature. The conversion of TCP was 74% in 30 min and 80% in 6 h when the catalyst was [FePTS]. Amberlite IRA-900 supported [FePTS] catalyst was also prepared. In the recycling experiments the homogeneous [FePTS] lost its activity after the first cycle, while [FePTS]-Amberlite IRA 900 maintained its activity for the first 2 cycles. After the second cycle, the conversion of TCP dropped to <10% for Amberlite IRA-900 supported [FePTS] catalyst. The degradation of TCP with PMS was also attempted using cobalt, copper, nickel and palladium porphyrin tetrasulfonate catalysts, however, no catalytic activity was observed with these structures. - Highlights: • The method presents an effective oxidation of TCP. • This research provided persistence, less harmful, self-degradable and more environmental oxidation products. • About seventy percent conversions of TCP in 30 min was achieved at room temperature. - This research provided non-persistent, less harmful, self-degradable and more environmentally friendly oxidation products. About 70% conversions of TCP in 30 min was achieved at room temperature.

Efficient activation of peroxymonosulfate by magnetic Mn-MGO for degradation of bisphenol A

Energy Technology Data Exchange (ETDEWEB)

Du, Jiangkun [School of Environmental Studies, China University of Geosciences, Wuhan 430074 (China); Bao, Jianguo, E-mail: bjianguo@cug.edu.cn [School of Environmental Studies, China University of Geosciences, Wuhan 430074 (China); Liu, Ying; Ling, Haibo; Zheng, Han [School of Environmental Studies, China University of Geosciences, Wuhan 430074 (China); Kim, Sang Hoon, E-mail: kim_sh@kist.re.kr [Center for Materials Architecturing, Korea Institute of Science and Technology, Seoul, 136-791 (Korea, Republic of); Dionysiou, Dionysios D., E-mail: dionysios.d.dionysiou@uc.edu [Environmental Engineering and Science Program, Department of Biomedical, Chemical and Environmental Engineering, 705 Engineering Research Center, University of Cincinnati, Cincinnati, OH 45221-0012 (United States)

2016-12-15

Highlights: Manganese catalyst was immobilized on Fe{sub 3}O{sub 4}/graphene hybrids to facilitate magnetic separation. Magnetic manganese catalyst exhibited high efficacy and long-term stability for catalytic PMS activation. The minerlization efficiency and the biotoxicity of BPA byproducts were evaluated. The degradation pathways of BPA and the possible activation mechanism of PMS were proposed. - Abstract: A heterogeneous manganese/magnetite/graphene oxide (Mn-MGO) hybrid catalyst was fabricated through the reduction of KMnO{sub 4} by ethylene glycol in the presence of magnetite/GO (MGO) particles. The Mn-MGO catalyst exhibited high efficacy and long-term stability in activating peroxymonosulfate (PMS) to generate sulfate radicals for the removal of bisphenol A (BPA) from water. The results of the batch experiments indicated that an increase in the catalyst dose and solution pH could enhance BPA degradation in the coupled Mn-MGO/PMS system. Regardless of the initial pH, the solution pH significantly dropped after the reaction, which was caused by catalytic PMS activation. The production of sulfate radicals and hydroxyl radicals was validated through radical quenching and electron paramagnetic resonances (EPR) tests. BPA degradation pathways were proposed on the basis of LC-MS and GC-MS analyses. Finally, a possible mechanism of catalytic PMS activation was proposed that involved electron transfer from MnO or Mn{sub 2}O{sub 3} to PMS with the generation of sulfate radicals, protons and MnO{sub 2}, as well as the simultaneous reduction of MnO{sub 2} by PMS.

Complexes of metal chlorides with proton donors — promising polyfunctional catalysts for electrophilic processes

Science.gov (United States)

Minsker, Karl S.; Ivanova, S. R.; Biglova, Raisa Z.

1995-05-01

The Bronsted acids formed as a result of the interaction of aluminium chlorides with Group I and II metal chlorides in the presence of proton-donating compounds are promising polyfunctional catalysts for electrophilic processes (polymerisation, depolymerisation and degradation of macromolecules, alkylation, desulfurisation, and hydrogenation). The factor determing the electrophilic activity and selectivity of the action of the catalysts is their acidity. This makes it possible to predict the direction of the changes in the activity and selectivity of the catalyst in specific chemical processes in conformity with the opposite variation rule: with increase in the acidity of the electrophilic catalyst, their activity increases but the selectivity of their action diminishes. The bibliography includes 72 references.

Catalyst inks and method of application for direct methanol fuel cells

Science.gov (United States)

Zelenay, Piotr; Davey, John; Ren, Xiaoming; Gottesfeld, Shimshon; Thomas, Sharon C.

2004-02-24

Inks are formulated for forming anode and cathode catalyst layers and applied to anode and cathode sides of a membrane for a direct methanol fuel cell. The inks comprise a Pt catalyst for the cathode and a Pt--Ru catalyst for the anode, purified water in an amount 4 to 20 times that of the catalyst by weight, and a perfluorosulfonic acid ionomer in an amount effective to provide an ionomer content in the anode and cathode surfaces of 20% to 80% by volume. The inks are prepared in a two-step process while cooling and agitating the solutions. The final solution is placed in a cooler and continuously agitated while spraying the solution over the anode or cathode surface of the membrane as determined by the catalyst content.

Ozone Decomposition on the Surface of Metal Oxide Catalyst

Directory of Open Access Journals (Sweden)

Batakliev Todor Todorov

2014-12-01

Full Text Available The catalytic decomposition of ozone to molecular oxygen over catalytic mixture containing manganese, copper and nickel oxides was investigated in the present work. The catalytic activity was evaluated on the basis of the decomposition coefficient which is proportional to ozone decomposition rate, and it has been already used in other studies for catalytic activity estimation. The reaction was studied in the presence of thermally modified catalytic samples operating at different temperatures and ozone flow rates. The catalyst changes were followed by kinetic methods, surface measurements, temperature programmed reduction and IR-spectroscopy. The phase composition of the metal oxide catalyst was determined by X-ray diffraction. The catalyst mixture has shown high activity in ozone decomposition at wet and dry O3/O2 gas mixtures. The mechanism of catalytic ozone degradation was suggested.

Photocatalytic degradation of sunscreen active ingredients mediated by nanostructured materials

Science.gov (United States)

Soto-Vazquez, Loraine

Water scarcity and pollution are environmental issues with terrible consequences. In recent years several pharmaceutical and personal care products, such as sunscreen active ingredients, have been detected in different water matrices. Its recalcitrant behavior in the environment has caused controversies and generated countless questions about its safety. During this research, we employed an advanced oxidation process (photocatalysis) to degrade sunscreen active ingredients. For this study, we used a 3x3 system, evaluating three photocatalysts and three different contaminants. From the three catalysts employed, two of them were synthesized. ZnO nanoparticles were obtained using zinc acetate dihydrated as the precursor, and TiO2 nanowires were synthesized from titanium tetrachloride precursor. The third catalyst employed (namely, P25) was obtained commercially. The synthesized photocatalysts were characterized in terms of the morphology, elemental composition, crystalline structure, elemental oxidation states, vibrational modes and surface area, using SEM-EDS, XRD, XPS, Raman spectroscopy and BET measurements, respectively. The photocatalysts were employed during the study of the degradation of p-aminobenzoic acid, phenylbenzimidazole sulfonic acid, and benzophenone-4. In all the cases, at least 50% degradation was achieved. P25 showed degradation efficiencies above 90%, and from the nine systems, 7 of them degraded at least 86%.

Design criteria for stable Pt/C fuel cell catalysts

Directory of Open Access Journals (Sweden)

Josef C. Meier

2014-01-01

Full Text Available Platinum and Pt alloy nanoparticles supported on carbon are the state of the art electrocatalysts in proton exchange membrane fuel cells. To develop a better understanding on how material design can influence the degradation processes on the nanoscale, three specific Pt/C catalysts with different structural characteristics were investigated in depth: a conventional Pt/Vulcan catalyst with a particle size of 3–4 nm and two Pt@HGS catalysts with different particle size, 1–2 nm and 3–4 nm. Specifically, Pt@HGS corresponds to platinum nanoparticles incorporated and confined within the pore structure of the nanostructured carbon support, i.e., hollow graphitic spheres (HGS. All three materials are characterized by the same platinum loading, so that the differences in their performance can be correlated to the structural characteristics of each material. The comparison of the activity and stability behavior of the three catalysts, as obtained from thin film rotating disk electrode measurements and identical location electron microscopy, is also extended to commercial materials and used as a basis for a discussion of general fuel cell catalyst design principles. Namely, the effects of particle size, inter-particle distance, certain support characteristics and thermal treatment on the catalyst performance and in particular the catalyst stability are evaluated. Based on our results, a set of design criteria for more stable and active Pt/C and Pt-alloy/C materials is suggested.

A Sustainable Nanocomposite Au(Salen)@CC for Catalytic Degradation of Eosin Y and Chromotrope 2R Dyes.

Science.gov (United States)

Mayani, Vishal J; Mayani, Suranjana V; Kim, Sang Wook

2017-08-03

Up to now, a very few catalysts have been developed approaching the heterogeneous catalytic degradation of Eosin Y and Chromotrope 2R dyes (Acid Red 29). The present study provides a complete perspective of recyclable nanocomposite Au(Salen)@CC for catalytic degradation of hazardous water pollutant dyes viz., Eosin Y & Chromotrope 2R using mild reaction conditions. New gold Salen complex doped carbon nanocomposite Au(Salen)@CC was developed by easy methodology using nano carbon cage (CC) prepared from low-priced Pyrolysis fuel oil (PFO) residue based Pitch. The UV-Vis adsorption spectroscopy results of Eosin Y and Chromotrope 2R dyes indicated complete degradation into acidic compounds which can be further mineralized to CO 2 and H 2 O under mild reaction conditions. The heterogeneous catalyst recycled and reused successfully for four repeated experiments without loss in its adequate performance. This new sustainable and eco-friendly catalyst delivered significant degradation activity compared to existing reports and it can be further utilized for new multifunctional applications such as, radiopharmaceutical activities, heterogeneous catalysis and chiral resolution.

Adsorption and bio-sorption of nickel ions and reuse for 2-chlorophenol catalytic ozonation oxidation degradation from water

Energy Technology Data Exchange (ETDEWEB)

Ma, Wei, E-mail: chmawv@yahoo.com [School of Chemical Engineering, Dalian University of Technology, Dalian 116024 (China); Zong, Panpan; Cheng, Zihong [School of Chemical Engineering, Dalian University of Technology, Dalian 116024 (China); Wang, Baodong; Sun, Qi [National Institute of Clean-and-low Carbon Energy, Beijing 102209 (China)

2014-02-15

Highlights: • Biomass and fly ash which were widespread for adsorption of heavy metal ions. • Preparation of catalyst by saturated adsorbents for 2-chlorophenol ozone degradation. • This work demonstrated that the O{sub 3}/catalyst process was an effective pathway. • The use of nickel ions, fly ash and sawdust to achieve the recycling utilization of resources. -- Abstract: This work explored the preparation of an effective and low-cost catalyst and investigated its catalytic capacity for 2-chlorophenol ozonation oxidation degradation in wastewater by using an ozone oxidation batch reactor. The catalyst was directly prepared by the reuse of fly ash and sawdust after saturated adsorption of nickel ions from wastewater, which was proposed as an efficient and economic approach. The obtained catalyst was characterized by TGA, BET, FTIR, XRD, and SEM, the results showed that fly ash as the basic framework has high specific surface area and the addition of sawdust as the porogen agent could improve the pore structure of the catalyst. The adsorption of nickel ions by fly ash and sawdust from aqueous solution was also investigated in this study. The results obtained from the experiments indicated that adsorption of nickel ions by fly ash and biomass sawdust could be well described by Langmuir isotherm model and pseudo second order kinetic model. The catalytic performance of catalyst was studied in terms of the effect of time, liquid–solid ratio and pH on 2-chlorophenol ozonation degradation. It was found that the catalyst could effectively improve the ozonation reaction rate at pH = 7 with a 2:1 liquid–solid ratio. The kinetic study demonstrated that the reaction followed the first order model, and the rate constant increased 267% (0.03–0.1 min{sup −1}) of 2-chlorophenol ozonation degradation with 5 mmol/L concentration at pH = 7.0 compared with ozonation alone.

Use of Pillared Clay-Based Catalysts for Wastewater Treatment through Fenton-Like Processes

OpenAIRE

J. Herney-Ramírez; Luis M. Madeira

2010-01-01

Clays, both natural and physical-chemically modified, are attractive materials for the preparation of supported catalysts. In this chapter, a review is made regarding the use of pillared interlayered clays (PILCs) in heterogeneous Fenton-like advanced oxidation processes. Their applications in pollutants degradation is summarized, with particular emphasis on the effect of the main operating conditions (e.g., initial H2O2 or parent compound concentration, catalyst load, pH, or temperature) on ...

Pt and PtRu catalyst bilayers increase efficiencies for ethanol oxidation in proton exchange membrane electrolysis and fuel cells

Science.gov (United States)

Altarawneh, Rakan M.; Pickup, Peter G.

2017-10-01

Polarization curves, product distributions, and reaction stoichiometries have been measured for the oxidation of ethanol at anodes consisting of Pt and PtRu bilayers and a homogeneous mixture of the two catalysts. These anode structures all show synergies between the two catalysts that can be attributed to the oxidation of acetaldehyde produced at the PtRu catalyst by the Pt catalyst. The use of a PtRu layer over a Pt layer produces the strongest effect, with higher currents than a Pt on PtRu bilayer, mixed layer, or either catalyst alone, except for Pt at high potentials. Reaction stoichiometries (average number of electrons transferred per ethanol molecule) were closer to the values for Pt alone for both of the bilayer configurations but much lower for PtRu and mixed anodes. Although Pt alone would provide the highest overall fuel cell efficiency at low power densities, the PtRu on Pt bilayer would provide higher power densities without a significant loss of efficiency. The origin of the synergy between the Pt and PtRu catalysts was elucidated by separation of the total current into the individual components for generation of carbon dioxide and the acetaldehyde and acetic acid byproducts.

Influence of HEPES buffer on the local pH and formation of surface layer during in vitro degradation tests of magnesium in DMEM

Directory of Open Access Journals (Sweden)

S. Naddaf Dezfuli

2014-10-01

Full Text Available The human body is a buffered environment where pH is effectively maintained. HEPES is a biological buffer often used to mimic the buffering activity of the body in in vitro studies on the degradation behavior of magnesium. However, the influence of HEPES on the degradation behavior of magnesium in the DMEM pseudo-physiological solution has not yet been determined. The research aimed at elucidating the degradation mechanisms of magnesium in DMEM with and without HEPES. The morphologies and compositions of surface layers formed during in vitro degradation tests for 15–3600 s were characterized. The effect of HEPES on the electrochemical behavior and corrosion tendency was determined by performing electrochemical tests. HEPES indeed retained the local pH, leading to intense intergranular/interparticle corrosion of magnesium made from powder and an increased degradation rate. This was attributed to an interconnected network of cracks formed at the original powder particle boundaries and grain boundaries in the surface layer, which provided pathways for the corrosive medium to interact continuously with the internal surfaces and promoted further dissolution. Surface analysis revealed significantly reduced amounts of precipitated calcium phosphates due to the buffering activity of HEPES so that magnesium became less well protected in the buffered environment.

Synergetic effect of Ag{sub 2}O as co-catalyst for enhanced photocatalytic degradation of phenol on N-TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Chu, Haipeng [Institute of Coordination Bond Metrology and Engineering, College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Liu, Xinjuan, E-mail: lxj669635@126.com [Institute of Coordination Bond Metrology and Engineering, College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Liu, Junying [Research Center for Combustion and Environment Technology, Shanghai Jiao Tong University, Shanghai 200240 (China); Li, Jinliang [Engineering Research Center for Nanophotonics & Advanced Instrument, Ministry of Education, School of Physics and Materials Science, East China Normal University, Shanghai 200062 (China); Wu, Tianyang; Li, Haokun; Lei, Wenyan; Xu, Yan [Institute of Coordination Bond Metrology and Engineering, College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Pan, Likun, E-mail: lkpan@phy.ecnu.edu.cn [Engineering Research Center for Nanophotonics & Advanced Instrument, Ministry of Education, School of Physics and Materials Science, East China Normal University, Shanghai 200062 (China)

2016-09-15

Graphical abstract: Ag{sub 2}O/N-TiO{sub 2} composites were synthesized via a co-precipitation method for visible light photocatalytic degradation of organic pollutions with excellent photocatalytic activity. - Highlights: • Ag{sub 2}O/N-TiO{sub 2} composites were synthesized via a facile precipitation method. • Ag{sub 2}O/N-TiO{sub 2} composites exhibited enhanced photocatalytic activity. • Ag{sub 2}O acts as co-catalyst to separate the photo-generated electron-hole pairs. - Abstract: A facile precipitation method was developed to synthesize the Ag{sub 2}O/N-TiO{sub 2} composites. Their morphology, structure and photocatalytic performance in the degradation of methylene blue (MB) and phenol under visible light irradiation were characterized by scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, photoluminescence spectroscopy and UV–vis absorption spectroscopy, respectively. The results show that the Ag{sub 2}O/N-TiO{sub 2} composites exhibit excellent photocatalytic performance. The maximum degradation rates of MB and phenol are about 8.9 and 2.9 times that of pure N-TiO{sub 2}, respectively. The excellent photocatalytic performance is mainly ascribed to the synergetic effects of Ag{sub 2}O and N-TiO{sub 2} including the increased light absorption and the reduced electron-hole pair recombination in N-TiO{sub 2} with the presence of Ag{sub 2}O.

Activation of peroxymonosulfate by graphitic carbon nitride loaded on activated carbon for organic pollutants degradation

International Nuclear Information System (INIS)

Wei, Mingyu; Gao, Long; Li, Jun; Fang, Jia; Cai, Wenxuan; Li, Xiaoxia; Xu, Aihua

2016-01-01

Highlights: • Supported g-C_3N_4 on AC catalysts with different loadings were prepared. • The metal free catalysts exhibited high efficiency for dyes degradation with PMS. • The catalyst presented a long-term stability for multiple runs. • The C=O groups played a key role in the oxidation process. - Abstract: Graphitic carbon nitride supported on activated carbon (g-C_3N_4/AC) was prepared through an in situ thermal approach and used as a metal free catalyst for pollutants degradation in the presence of peroxymonosulfate (PMS) without light irradiation. It was found that g-C_3N_4 was highly dispersed on the surface of AC with the increase of surface area and the exposition of more edges and defects. The much easier oxidation of C species in g-C_3N_4 to C=O was also observed from XPS spectra. Acid Orange 7 (AO7) and other organic pollutants could be completely degraded by the g-C_3N_4/AC catalyst within 20 min with PMS, while g-C_3N_4+PMS and AC+PMS showed no significant activity for the reaction. The performance of the catalyst was significantly influenced by the amount of g-C_3N_4 loaded on AC; but was nearly not affected by the initial solution pH and reaction temperature. In addition, the catalysts presented good stability. A nonradical mechanism accompanied by radical generation (HO· and SO_4·"−) in AO7 oxidation was proposed in the system. The C=O groups play a key role in the process; while the exposure of more N-(C)_3 group can further increase its electron density and basicity. This study can contribute to the development of green materials for sustainable remediation of aqueous organic pollutants.

Bio-inspired MOF-based Catalysts for Lignin Valorization.

Energy Technology Data Exchange (ETDEWEB)

Allendorf, Mark D.; Stavila, Vitalie; Ramakrishnan, Parthasarathi; Davis, Ryan Wesley

2014-09-01

Lignin is a potentially plentiful source of renewable organics, with %7E50Mtons/yr produced by the pulp/paper industry and 200-300 Mtons/yr projected production by a US biofuels industry. This industry must process approximately 1 billion tons of biomass to meet the US Renewable Fuel goals. However, there are currently no efficient processes for converting lignin to value-added chemicals and drop-in fuels. Lignin is therefore an opportunity for production of valuable renewable chemicals, but presents staggering technical and economic challenges due to the quantities of material involved and the strong chemical bonds comprising this polymer. Aggressive chemistries and high temperatures are required to degrade lignin without catalysts. Moreover, chemical non-uniformity among lignins leads to complex product mixtures that tend to repolymerize. Conventional petrochemical approaches (pyrolysis, catalytic cracking, gasification) are energy intensive (400-800 degC), require complicated separations, and remove valuable chemical functionality. Low-temperature (25-200 degC) alternatives are clearly desirable, but enzymes are thermally fragile and incompatible with liquid organic compounds, making them impractical for large-scale biorefining. Alternatively, homogeneous catalysts, such as recently developed vanadium complexes, must be separated from product mixtures, while many heterogenous catalysts involve costly noble metals. The objective of this project is to demonstrate proof of concept that an entirely new class of biomimetic, efficient, and industrially robust synthetic catalysts based on nanoporous Metal- Organic Frameworks (MOFs) can be developed. Although catalytic MOFs are known, catalysis of bond cleavage reactions needed for lignin degradation is completely unexplored. Thus, fundamental research is required that industry and most sponsoring agencies are currently unwilling to undertake. We introduce MOFs infiltrated with titanium and nickel species as catalysts

Photocatalytic degradation of rosuvastatin: Analytical studies and toxicity evaluations

Energy Technology Data Exchange (ETDEWEB)

Machado, Tiele Caprioli, E-mail: tiele@enq.ufrgs.br [Chemical Engineering Department, Federal University of Rio Grande do Sul, Rua Engenheiro Luiz Englert s/n, CEP: 90040-040 Porto Alegre, RS (Brazil); Pizzolato, Tânia Mara [Chemical Institute, Federal University of Rio Grande do Sul, Avenida Bento Gonçalves, 9500, CEP: 91501-970 Porto Alegre, RS (Brazil); Arenzon, Alexandre [Ecology Center, Federal University of Rio Grande do Sul, Avenida Bento Gonçalves, 9500, CEP: 91501-970 Porto Alegre, RS (Brazil); Segalin, Jeferson [Biotechnology Center, Federal University of Rio Grande do Sul, Avenida Bento Gonçalves, 9500, CEP: 91501-970 Porto Alegre, RS (Brazil); Lansarin, Marla Azário [Chemical Engineering Department, Federal University of Rio Grande do Sul, Rua Engenheiro Luiz Englert s/n, CEP: 90040-040 Porto Alegre, RS (Brazil)

2015-01-01

Photocatalytic degradation of rosuvastatin, which is a drug that has been used to reduce blood cholesterol levels, was studied in this work employing ZnO as catalyst. The experiments were carried out in a temperature-controlled batch reactor that was irradiated with UV light. Preliminary the effects of the photocatalyst loading, the initial pH and the initial rosuvastatin concentration were evaluated. The experimental results showed that rosuvastatin degradation is primarily a photocatalytic process, with pseudo-first order kinetics. The byproducts that were generated during the oxidative process were identified using nano-ultra performance liquid chromatography tandem mass spectrometry (nano-UPLC–MS/MS) and acute toxicity tests using Daphnia magna were done to evaluate the toxicity of the untreated rosuvastatin solution and the reactor effluent. - Highlights: • The photocatalytic degradation of rosuvastatin was studied under UV irradiation. • Commercial catalyst ZnO was used. • Initial rosuvastatin concentration, photocatalyst loading and pH were evaluated. • The byproducts generated during the oxidative process were detected and identified. • Acute toxicity tests using Daphnia magna were carried out.

Bimetallic Nickel/Ruthenium Catalysts Synthesized by Atomic Layer Deposition for Low-Temperature Direct Methanol Solid Oxide Fuel Cells.

Science.gov (United States)

Jeong, Heonjae; Kim, Jun Woo; Park, Joonsuk; An, Jihwan; Lee, Tonghun; Prinz, Fritz B; Shim, Joon Hyung

2016-11-09

Nickel and ruthenium bimetallic catalysts were heterogeneously synthesized via atomic layer deposition (ALD) for use as the anode of direct methanol solid oxide fuel cells (DMSOFCs) operating in a low-temperature range. The presence of highly dispersed ALD Ru islands over a porous Ni mesh was confirmed, and the Ni/ALD Ru anode microstructure was observed. Fuel cell tests were conducted using Ni-only and Ni/ALD Ru anodes with approximately 350 μm thick gadolinium-doped ceria electrolytes and platinum cathodes. The performance of fuel cells was assessed using pure methanol at operating temperatures of 300-400 °C. Micromorphological changes of the anode after cell operation were investigated, and the content of adsorbed carbon on the anode side of the operated samples was measured. The difference in the maximum power density between samples utilizing Ni/ALD Ru and Pt/ALD Ru, the latter being the best catalyst for direct methanol fuel cells, was observed to be less than 7% at 300 °C and 30% at 350 °C. The improved electrochemical activity of the Ni/ALD Ru anode compared to that of the Ni-only anode, along with the reduction of the number of catalytically active sites due to agglomeration of Ni and carbon formation on the Ni surface as compared to Pt, explains this decent performance.

Pt-Pd bimetallic nanoparticles on MWCNTs: catalyst for hydrogen peroxide electrosynthesis

Energy Technology Data Exchange (ETDEWEB)

Felix-Navarro, R. M., E-mail: moi6salazar@hotmail.com; Beltran-Gastelum, M.; Salazar-Gastelum, M. I.; Silva-Carrillo, C.; Reynoso-Soto, E. A.; Perez-Sicairos, S.; Lin, S. W. [Centro de Graduados e Investigacion, Instituto Tecnologico de Tijuana (Mexico); Paraguay-Delgado, F. [Centro de Investigacion en Materiales Avanzados (Mexico); Alonso-Nunez, G. [Centro de Nanociencias y Nanotecnologia (Mexico)

2013-08-15

Bimetallic nanoparticles of Pt-Pd were deposited by the microemulsion method on a multiwall carbon nanotube (MWCNTs) to obtain a Pt-Pd/MWCNTs for electrocatalytic reduction of O{sub 2} to H{sub 2}O{sub 2}. The activity and selectivity of the catalyst was determined qualitatively by the rotating disk electrode method in acidic medium. The catalyst was spray-coated onto a reticulated vitreous carbon substrate and quantitatively was tested in bulk electrolysis for 20 min under potentiostatic conditions (0.5 V vs Ag/AgCl) in a 0.5 M H{sub 2}SO{sub 4} electrolyte using dissolved O{sub 2}. The bulk electrolysis experiments show that the Pt-Pd/MWCNTs catalyst is more efficient for H{sub 2}O{sub 2} electrogeneration than a MWCNTs catalyst. Nitrobenzene degradation by electrogenerated H{sub 2}O{sub 2} alone and Electro-Fenton process were also tested. Our results show that both processes decompose nitrobenzene, but the Electro-Fenton process does it more efficiently. The prepared nanoparticulated catalyst shows a great potential in environmental applications.

Photodriven hydrogen evolution by molecular catalysts using Al2O3-protected perylene-3,4-dicarboximide on NiO electrodes† †Electronic supplementary information (ESI) available: Experimental details; additional electrochemical and photoelectrochemical characterization, UV-Vis spectra, and fsTA results; quantification of evolved hydrogen; and DFT-computed ground state structure of PMI diester. See DOI: 10.1039/c6sc02477g Click here for additional data file.

Science.gov (United States)

Kamire, Rebecca J.; Majewski, Marek B.; Hoffeditz, William L.; Phelan, Brian T.; Farha, Omar K.; Hupp, Joseph T.

2017-01-01

The design of efficient hydrogen-evolving photocathodes for dye-sensitized photoelectrochemical cells (DSPECs) requires the incorporation of molecular light absorbing chromophores that are capable of delivering reducing equivalents to molecular proton reduction catalysts at rates exceeding those of charge recombination events. Here, we report the functionalization and kinetic analysis of a nanostructured NiO electrode with a modified perylene-3,4-dicarboximide chromophore (PMI) that is stabilized against degradation by atomic layer deposition (ALD) of thick insulating Al2O3 layers. Following photoinduced charge injection into NiO in high yield, films with Al2O3 layers demonstrate longer charge separated lifetimes as characterized via femtosecond transient absorption spectroscopy and photoelectrochemical techniques. The photoelectrochemical behavior of the electrodes in the presence of Co(ii) and Ni(ii) molecular proton reduction catalysts is examined, revealing reduction of both catalysts. Under prolonged irradiation, evolved H2 is directly observed by gas chromatography supporting the applicability of PMI embedded in Al2O3 as a photocathode architecture in DSPECs. PMID:28616134

Ultra-Fast Degradation of Chemical Warfare Agents Using MOF-Nanofiber Kebabs.

Science.gov (United States)

Zhao, Junjie; Lee, Dennis T; Yaga, Robert W; Hall, Morgan G; Barton, Heather F; Woodward, Ian R; Oldham, Christopher J; Walls, Howard J; Peterson, Gregory W; Parsons, Gregory N

2016-10-10

The threat associated with chemical warfare agents (CWAs) motivates the development of new materials to provide enhanced protection with a reduced burden. Metal-organic frame-works (MOFs) have recently been shown as highly effective catalysts for detoxifying CWAs, but challenges still remain for integrating MOFs into functional filter media and/or protective garments. Herein, we report a series of MOF-nanofiber kebab structures for fast degradation of CWAs. We found TiO 2 coatings deposited via atomic layer deposition (ALD) onto polyamide-6 nanofibers enable the formation of conformal Zr-based MOF thin films including UiO-66, UiO-66-NH 2 , and UiO-67. Cross-sectional TEM images show that these MOF crystals nucleate and grow directly on and around the nanofibers, with strong attachment to the substrates. These MOF-functionalized nanofibers exhibit excellent reactivity for detoxifying CWAs. The half-lives of a CWA simulant compound and nerve agent soman (GD) are as short as 7.3 min and 2.3 min, respectively. These results therefore provide the earliest report of MOF-nanofiber textile composites capable of ultra-fast degradation of CWAs. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Study on hydrophobicity degradation of gas diffusion layer in proton exchange membrane fuel cells

International Nuclear Information System (INIS)

Yu, Shuchun; Li, Xiaojin; Li, Jin; Liu, Sa; Lu, Wangting; Shao, Zhigang; Yi, Baolian

2013-01-01

Highlights: • The hydrophobicity degradation mechanism of GDL was proposed thoroughly. • C-O and C=O groups appeared on the surfaces of GDL after immersion. • The relative content of PTFE in GDL decreased after immersion. • The surfaces and inner structure of GDL destroyed after immersion. - Abstract: As one of the essential components of proton exchange membrane fuel cell (PEMFC), gas diffusion layer (GDL) is of importance on water management, as well on the performance and durability of PEMFC. In this paper, the hydrophobicity degradation of GDL was investigated by immersing it in the 1.0 mol L −1 H 2 SO 4 solution saturated by air for 1200 h. From the measurements of contact angle and water permeability, the hydrophobic characteristics of the pristine and immersed GDLs were compared. To investigate the causes for hydrophobicity degradation, the GDLs were analyzed by scanning electron microscopy, X-ray photoelectron spectroscopy and thermogravimetry. Further, the chemical compositions of H 2 SO 4 solutions before and after immersion test were analyzed with infrared spectroscopy. Results showed that the hydrophobicity of immersed GDL decreased distinctly, which was caused by the damage of physical structure and surface characteristics. Moreover, the immersed GDL showed a worse fuel cell performance than the pristine GDL, especially under a low humidity condition

Co-deposition of Pt and ceria anode catalyst in supercritical carbon dioxide for direct methanol fuel cell applications

International Nuclear Information System (INIS)

You, Eunyoung; Guzmán-Blas, Rolando; Nicolau, Eduardo; Aulice Scibioh, M.; Karanikas, Christos F.; Watkins, James J.; Cabrera, Carlos R.

2012-01-01

Pt and mixed Pt-ceria catalysts were deposited onto gas diffusion layers using supercritical fluid deposition (SFD) to fabricate thin layer electrodes for direct methanol fuel cells. Dimethyl (1,5-cyclooctadiene) platinum (II) (CODPtMe 2 ) and tetrakis (2,2,6,6-tetramethyl 3,5-heptanedionato) cerium (IV) (Ce(tmhd) 4 ) were used as precursors. Hydrogen-assisted Pt deposition was performed in compressed carbon dioxide at 60 °C and 17.2 MPa to yield high purity Pt on carbon-black based gas diffusion layers. During the preparation of the mixed Pt-ceria catalyst, hydrogen reduction of CODPtMe 2 to yield Pt catalyzed the deposition of ceria from Ce(tmhd) 4 enabling co-deposition at 150 °C. The catalyst layers were characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscope-energy dispersive spectral (SEM-EDS) analyses. Their electrochemical performance toward methanol oxidation was examined in half cell mode using a three electrode assembly as well as in fuel cell mode. The thin layer electrodes formed via SFD exhibited higher performance in fuel cell operations compared to those prepared by the conventional brush-paint method. Furthermore, the Pt-ceria catalyst with an optimized composition exhibited greater methanol oxidation activity than pure platinum.

Catalytic degradation of waste high-density polyethylene into fuel products using BaCO{sub 3} as a catalyst

Energy Technology Data Exchange (ETDEWEB)

Jan, M. Rasul; Shah, Jasmin; Gulab, Hussain [Institute of Chemical Sciences, University of Peshawar, N.W.F.P. (Pakistan)

2010-11-15

Waste high-density polyethylene (HDPE) was degraded thermally and catalytically using BaCO{sub 3} as a catalyst under different conditions of temperature, cat/pol ratio and time. The oil collected at optimum conditions (450 C, 0.1 cat/pol ratio and 2 h reaction time) was fractionated at different temperatures and fuel property of the fractions and parent oil was evaluated by their physicochemical parameters for fuel tests. The results were compared with the standard values for gasoline, kerosene and diesel oil. Boiling point distribution (BPD) curves were plotted from the gas chromatographic study of the samples and compared with that of the standard gasoline, kerosene and diesel. The oil samples were analyzed using GC/MS in order to find out their composition. The physical parameters and the composition of the parent oil and its fractions support the resemblance of the samples with the standard fuel oils. The light fractions best match with gasoline, the middle fractions match with kerosene and the heavier fractions match with diesel oil in almost all of the characteristic properties. (author)

Rational design of Mg-Al mixed oxide-supported bimetallic catalysts for dry reforming of methane

Energy Technology Data Exchange (ETDEWEB)

Tsyganok, Andrey I. [Centre for Catalysis Research and Innovation, Department of Chemistry, University of Ottawa, D' Iorio Hall, 10 Marie Curie Street, Ottawa, Ont. (Canada); Inaba, Mieko [Natural Gas Technology Development Team, Teikoku Oil Co., 9-23-30 Kitakarasuyama, Setagaya-ku, Tokyo 157-0061 (Japan); Tsunoda, Tatsuo; Uchida, Kunio; Suzuki, Kunio; Hayakawa, Takashi [Institute for Materials and Chemical Process, National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba Central 5, 1-1-1 Higashi, Tsukuba 305-8565 (Japan); Takehira, Katsuomi [Department of Applied Chemistry, Faculty of Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi-Hiroshima 739-8527 (Japan)

2005-09-18

A novel synthetic strategy for preparing bimetallic Ru-M (M=Cr, Fe, Co, Ni and Cu) catalysts, supported on Mg-Al mixed oxide, has been introduced. It was based on a 'memory effect', i.e. on the ability of Mg-Al mixed oxide to reconstruct a layered structure upon rehydration with an aqueous solution. By repeated calcinations-rehydration cycles, layered double hydroxide (LDH) precursors of catalysts containing two different metals were synthesized. Bimetallic catalysts were then generated (1) in situ from LDH under methane reforming reaction conditions and (2) from mixed metal oxides obtained by preliminary LDH calcination. Among all the LDH-derived catalysts, a Ru{sup 0.1%}-Ni{sup 5.0%}/MgAlO{sub x} sample revealed the highest activity and selectivity to syngas, a suitable durability and a low coking capacity. A promoting effect of ruthenium on catalytic function of supported nickel was demonstrated. Preliminary LDH calcination was shown to markedly affect the catalytic activity of the derived catalysts and especially their coking properties.

Cobalt-embedded carbon nanofiber derived from a coordination polymer as a highly efficient heterogeneous catalyst for activating oxone in water.

Science.gov (United States)

Lin, Kun-Yi Andrew; Tong, Wai-Chi; Du, Yunchen

2018-03-01

Carbon fiber (CF) supported cobalt nanoparticles (NPs) are promising catalysts for activating Oxone because carbon is non-metal and earth-abundant, and CF-based catalysts exhibit a high aspect ratio, which affords more accessible and dense catalytic sites. Nevertheless, most of CF-supported catalysts are fabricated by post-synthetic methods, which involve complicated preparations. More importantly, metallic NPs are attached to the outer surface of CF rather than embedded within CF. However, there is still a great demand for developing Co-bearing carbon fibers for Oxone activation via simple and effective methods. Thus, this study proposes to develop a cobalt NP-embedded carbon nanofiber (CCNF) by a simple hydrothermal reaction of Co and nitrilotriacetic acid (NA), followed by one-step carbonization. Owing to the coordinative structure of CoNA, the derivative CCNF exhibits a fibrous carbon matrix embedded with evenly distributed and densely packed Co 3 O 4 and magnetic Co 0 nanoparticles. The fibrous structure, magnetism and embedded Co NPs enable CCNF to be a promising catalyst for Oxone activation. As degradation of Rhodamine B (RhB) is selected as a model reaction, CCNF not only rapidly activates Oxone to fully degrade RhB but also shows a much higher catalytic activity than the most common Oxone activator, Co 3 O 4 . CCNF also exhibits the lowest activation energy than any reported catalysts for Oxone activation to degrade RhB. In addition, CCNF could be re-used to activate Oxone for RhB degradation. These results indicate that CCNF is a conveniently prepared and highly effective fibrous Co/C hybrid material for activating Oxone to oxidize contaminants in water. Copyright © 2017. Published by Elsevier Ltd.

Investigation of electrolyte leaching in the performance degradation of phosphoric acid-doped polybenzimidazole membrane-based high temperature fuel cells

Science.gov (United States)

Jeong, Yeon Hun; Oh, Kyeongmin; Ahn, Sungha; Kim, Na Young; Byeon, Ayeong; Park, Hee-Young; Lee, So Young; Park, Hyun S.; Yoo, Sung Jong; Jang, Jong Hyun; Kim, Hyoung-Juhn; Ju, Hyunchul; Kim, Jin Young

2017-09-01

Precise monitoring of electrolyte leaching in high-temperature polymer electrolyte membrane fuel cell (HT-PEMFC) devices during lifetime tests is helpful in making a diagnosis of their quality changes and analyzing their electrochemical performance degradation. Here, we investigate electrolyte leaching in the performance degradation of phosphoric acid (PA)-doped polybenzimidazole (PBI) membrane-based HT-PEMFCs. We first perform quantitative analyses to measure PA leakage during cell operation by spectrophotometric means, and a higher PA leakage rate is detected when the current density is elevated in the cell. Second, long-term degradation tests under various current densities of the cells and electrochemical impedance spectroscopy (EIS) analysis are performed to examine the influence of PA loss on the membrane and electrodes during cell performance degradation. The combined results indicate that PA leakage affect cell performance durability, mostly due to an increase in charge transfer resistance and a decrease in the electrochemical surface area (ECSA) of the electrodes. Additionally, a three-dimensional (3-D) HT-PEMFC model is applied to a real-scale experimental cell, and is successfully validated against the polarization curves measured during various long-term experiments. The simulation results highlight that the PA loss from the cathode catalyst layer (CL) is a significant contributor to overall performance degradation.

LiFePO4 microcrystals as an efficient heterogeneous Fenton-like catalyst in degradation of rhodamine 6G.

Science.gov (United States)

Li, Zhan Jun; Ali, Ghafar; Kim, Hyun Jin; Yoo, Seong Ho; Cho, Sung Oh

2014-01-01

We present a novel heterogeneous Fenton-like catalyst of LiFePO4 (LFP). LFP has been widely used as an electrode material of a lithium ion battery, but we observed that commercial LFP (LFP-C) could act as a good Fenton-like catalyst to decompose rhodamine 6G. The catalytic activity of LFP-C microparticles was much higher than a popular catalyst, magnetite nanoparticles. Furthermore, we found that the catalytic activity of LFP-C could be further increased by increasing the specific surface area. The reaction rate constant of the hydrothermally synthesized LFP microcrystals (LFP-H) is at least 18 times higher than that of magnetite nanoparticles even though the particle size of LFP is far larger than magnetite nanoparticles. The LFP catalysts also exhibited a good recycling behavior and high stability under an oxidizing environment. The effects of the experimental parameters such as the concentration of the catalysts, pH, and the concentration of hydrogen peroxide on the catalytic activity of LFP were also analyzed.

Enhanced hydrothermal stability of Cu-ZSM-5 catalyst via surface modification in the selective catalytic reduction of NO with NH_3

International Nuclear Information System (INIS)

Zhang, Tao; Shi, Juan; Liu, Jian; Wang, Daxi; Zhao, Zhen; Cheng, Kai; Li, Jianmei

2016-01-01

Highlights: • The hydrothermal stability of Cu-ZSM-5 catalyst was enhanced after surface modification. • An inert silica layer was deposited on the surface of Cu-ZSM-5 and formed a protective layer. • The contact between Si and Cu and Al atoms could form Si-O-Al and Si- O−Cu bonds. • The redox and acidity properties of Cu-ZSM-5-CLD-Aged catalyst were largely retained. • The adsorption and activation of NO and NH_3 was almost unchanged over Cu-ZSM-5-CLD catalyst before and after hydrothermal treatment. - Abstract: The surface of Cu-ZSM-5 catalyst was modified by chemical liquid deposition (CLD) of tetraethoxysilane (TEOS) for enhancing its hydrothermal stability in the selective catalytic reduction of NO with NH_3. After hydrothermal aging at 750 °C for 13 h, the catalytic performance of Cu-ZSM-5-Aged catalyst was significantly reduced for NO reduction in the entire temperature range, while that of Cu-ZSM-5-CLD-Aged catalyst was affected very little. The characterization results indicated that an inert silica layer was deposited on the surface of Cu-ZSM-5 and formed a protective layer, which prevents the detachment of Cu"2"+ from ZSM-5 ion-exchange positions and the dealumination of zeolite during the hydrothermal aging process. Based on the data it is hypothesized to be the primary reason for the high hydrothermal stability of Cu-ZSM-5-CLD catalyst.

Photocatalytic degradation of tetracycline by Ti-MCM-41 prepared at room temperature and biotoxicity of degradation products

Science.gov (United States)

Zhou, Kefu; Xie, Xiao-Dan; Chang, Chang-Tang

2017-09-01

Ti-doped MCM-41 with different Si/Ti molar ratios was prepared at room temperature to degrade tetracycline antibiotics in aqueous solution. The Ti was doped into the skeleton structure of MCM-41. The photocatalytic activity of Ti-doped MCM-41 was investigated. The optimal catalyst had Si/Ti molar ratio of 25 and over 99% removal of oxytetracycline in 150 min, and the removal could maintain 98% after 5 reuses. Ions and soluble organic matters in natural water affected the degradation reaction when Ti-doped MCM-41 was used to treat simulated wastewater of chicken farms. The degradation products of oxytetracycline, tetracycline and chlortetracycline were detected by Escherichia coli DH5α and HPLC-MS/MS. No intermediate product with higher toxicity was detected.

Low-temperature catalyst activator: mechanism of dense carbon nanotube forest growth studied using synchrotron radiation

Directory of Open Access Journals (Sweden)

Akito Takashima

2014-07-01

Full Text Available The mechanism of the one-order-of-magnitude increase in the density of vertically aligned carbon nanotubes (CNTs achieved by a recently developed thermal chemical vapor deposition process was studied using synchrotron radiation spectroscopic techniques. In the developed process, a Ti film is used as the underlayer for an Fe catalyst film. A characteristic point of this process is that C2H2 feeding for the catalyst starts at a low temperature of 450°C, whereas conventional feeding temperatures are ∼800°C. Photoemission spectroscopy using soft and hard X-rays revealed that the Ti underlayer reduced the initially oxidized Fe layer at 450°C. A photoemission intensity analysis also suggested that the oxidized Ti layer at 450°C behaved as a support for nanoparticle formation of the reduced Fe, which is required for dense CNT growth. In fact, a CNT growth experiment, where the catalyst chemical state was monitored in situ by X-ray absorption spectroscopy, showed that the reduced Fe yielded a CNT forest at 450°C. Contrarily, an Fe layer without the Ti underlayer did not yield such a CNT forest at 450°C. Photoemission electron microscopy showed that catalyst annealing at the conventional feeding temperature of 800°C caused excess catalyst agglomeration, which should lead to sparse CNTs. In conclusion, in the developed growth process, the low-temperature catalyst activation by the Ti underlayer before the excess Fe agglomeration realised the CNT densification.

Discoloration of a red cationic dye by supported TiO2 photocatalysis

International Nuclear Information System (INIS)

Mounir, B.; Pons, M.N.; Zahraa, O.; Yaacoubi, A.; Benhammou, A.

2007-01-01

The degradation under UV, visible and sunlight irradiation of C.I. Basic Red 46 (BR 46) dye used for acrylic fibers dyeing has been studied in a lab-scale continuous system with two different immobilized TiO 2 systems. Catalyst I was based on TiO 2 particles deposited on cellulose fibers; Catalyst II combined TiO 2 particles deposited on a layer of cellulose fibers (as in Catalyst I) with a layer of carbon fibers and finally a layer of cellulose fibers. The treatment of aqueous dye solutions and industrial wastewater contaminated with the same dye has been evaluated in terms of color removal and chemical oxygen demand (COD) decrease. With UV light, aqueous solutions containing dye were decolorized slightly more rapidly with Catalyst II than with Catalyst I. Sunlight was also very effective and experiments involving sunlight irradiation showed Catalyst II to be the more efficient, giving more than 90% discoloration after 20 min of treatment. Comparing the discoloration yield by adsorption or under visible light for both catalysts, it was observed that the difference between them is below 5%. The adsorption kinetics was found to follow a second-order rate law for Catalyst I and a first-order rate law for Catalyst II. The kinetics of photocatalytic degradation under UV or sunlight were found to follow a first-order rate law for both catalytic systems. Under sunlight the COD removal yield for textile wastewater reaches 33% with Catalyst I against 93% with Catalyst II

Growth Mechanism of Single-Walled Carbon Nanotubes on Iron–Copper Catalyst and Chirality Studies by Electron Diffraction

DEFF Research Database (Denmark)

He, Maoshuai; Liu, Bilu; Chernov, Alexander I.

2012-01-01

Chiralities of single-walled carbon nanotubes grown on an atomic layer deposition prepared bimetallic FeCu/MgO catalyst were evaluated quantitatively using nanobeam electron diffraction. The results reveal that the growth yields nearly 90% semiconducting tubes, 45% of which are of the (6,5) type...... by impregnation, showing similar catalytic performance as the atomic layer deposition-prepared catalyst, yielding single-walled carbon nanotubes with a similar narrow chirality distribution....

Photocatalytic degradation of diethyl phthalate using TiO{sub 2} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Singla, Pooja, E-mail: pooja.singla@thapar.edu; Pandey, O. P., E-mail: pooja.singla@thapar.edu; Singh, K., E-mail: pooja.singla@thapar.edu [School of Physics and Materials Science, Thapar University, Patiala-147004 (India)

2014-04-24

TiO{sub 2} nanoparticles predominantly in rutile phase are synthesized by ultrasonication assisted sol-gel method. TiO{sub 2} powder is characterized using X-ray powder diffraction and UV-vis diffuse reflectance. TiO{sub 2} is used as catalyst in photocatalytic degradation of Diethyl Phthalate. TiO{sub 2} exhibits good photocatalytic activity for the degradation of diethyl phthalate.

Laser Ablation Increases PEM/Catalyst Interfacial Area

Science.gov (United States)

Whitacre, Jay; Yalisove, Steve

2009-01-01

An investigational method of improving the performance of a fuel cell that contains a polymer-electrolyte membrane (PEM) is based on the concept of roughening the surface of the PEM, prior to deposition of a thin layer of catalyst, in order to increase the PEM/catalyst interfacial area and thereby increase the degree of utilization of the catalyst. The roughening is done by means of laser ablation under carefully controlled conditions. Next, the roughened membrane surface is coated with the thin layer of catalyst (which is typically platinum), then sandwiched between two electrode/catalyst structures to form a membrane/ele c t - rode assembly. The feasibility of the roughening technique was demonstrated in experiments in which proton-conducting membranes made of a perfluorosulfonic acid-based hydrophilic, protonconducting polymer were ablated by use of femtosecond laser pulses. It was found that when proper combinations of the pulse intensity, pulse-repetition rate, and number of repetitions was chosen, the initially flat, smooth membrane surfaces became roughened to such an extent as to be converted to networks of nodules interconnected by filaments (see Figure 1). In further experiments, electrochemical impedance spectroscopy (EIS) was performed on a pristine (smooth) membrane and on two laser-roughened membranes after the membranes were coated with platinum on both sides. Some preliminary EIS data were interpreted as showing that notwithstanding the potential for laser-induced damage, the bulk conductivities of the membranes were not diminished in the roughening process. Other preliminary EIS data (see Figure 2) were interpreted as signifying that the surface areas of the laser-roughened membranes were significantly greater than those of the smooth membrane. Moreover, elemental analyses showed that the sulfur-containing molecular groups necessary for proton conduction remained intact, even near the laser-roughened surfaces. These preliminary results can be taken

Oxidation catalyst

Science.gov (United States)

Ceyer, Sylvia T.; Lahr, David L.

2010-11-09

The present invention generally relates to catalyst systems and methods for oxidation of carbon monoxide. The invention involves catalyst compositions which may be advantageously altered by, for example, modification of the catalyst surface to enhance catalyst performance. Catalyst systems of the present invention may be capable of performing the oxidation of carbon monoxide at relatively lower temperatures (e.g., 200 K and below) and at relatively higher reaction rates than known catalysts. Additionally, catalyst systems disclosed herein may be substantially lower in cost than current commercial catalysts. Such catalyst systems may be useful in, for example, catalytic converters, fuel cells, sensors, and the like.

Application of a Coated Film Catalyst Layer Model to a High Temperature Polymer Electrolyte Membrane Fuel Cell with Low Catalyst Loading Produced by Reactive Spray Deposition Technology

Directory of Open Access Journals (Sweden)

Timothy D. Myles

2015-10-01

Full Text Available In this study, a semi-empirical model is presented that correlates to previously obtained experimental overpotential data for a high temperature polymer electrolyte membrane fuel cell (HT-PEMFC. The goal is to reinforce the understanding of the performance of the cell from a modeling perspective. The HT-PEMFC membrane electrode assemblies (MEAs were constructed utilizing an 85 wt. % phosphoric acid doped Advent TPS® membranes for the electrolyte and gas diffusion electrodes (GDEs manufactured by Reactive Spray Deposition Technology (RSDT. MEAs with varying ratios of PTFE binder to carbon support material (I/C ratio were manufactured and their performance at various operating temperatures was recorded. The semi-empirical model derivation was based on the coated film catalyst layer approach and was calibrated to the experimental data by a least squares method. The behavior of important physical parameters as a function of I/C ratio and operating temperature were explored.

Rapid degradation of Congo red by molecularly imprinted polypyrrole-coated magnetic TiO2 nanoparticles in dark at ambient conditions

International Nuclear Information System (INIS)

Wei, Shoutai; Hu, Xiaolei; Liu, Hualong; Wang, Qiang; He, Chiyang

2015-01-01

Highlights: • Molecularly imprinted polypyrrole-coated magnetic TiO 2 catalyst was prepared. • The catalyst degraded Congo red rapidly in dark at ambient conditions. • Degradation mechanism was proposed according to LC–MS analysis. • The catalyst can be easily recycled by a magnet. - Abstract: A novel molecularly imprinted polymer (MIP)-coated magnetic TiO 2 nanocomposite was prepared, using methyl orange (MO) as the dummy template and pyrrole as functional monomer, for degradation of Congo red (CR). The nanocomposite was characterized by Fourier transform infrared spectroscopy, thermo-gravimetric analysis, X-ray diffraction, transmission electron microscopy, and vibrating sample magnetometer. The imprinting efficiency of the imprinted nanoparticles was investigated by static binding test, and their degradation ability toward CR was also studied. Moreover, the effects of pH, temperature, dissolved oxygen and oscillation rate on degradation rate of CR were investigated. Results showed that the imprinted nanocomposite had higher adsorption ability for MO compared with the non-imprinted one. Moreover, it could degrade CR rapidly in dark at room temperature and atmospheric pressure and could be recycled easily by a magnet with a good reusability. A degradation mechanism was proposed according to LC–MS analysis of degradation products of CR. The new imprinted nanoparticles showed high catalytic activity at ambient conditions without light illumination and additional chemicals, and therefore, it can be potentially applied to the rapid, “green” and low-cost degradation of CR in industrial printing and dyeing wastewater

New fillers in the synthesis of polypropylene nano composites with Ziegler-Natta catalysts

International Nuclear Information System (INIS)

Rosa, Jeferson L.S.; Silva, Marcelo C.V.; Marques, Maria F.V.

2011-01-01

In this study, Ziegler-Natta catalysts bi-supported on MgCl 2 and natural clays were prepared in order to synthesize polypropylene nanocomposites. The employed clays were bentonite, as reference, as well as halloysite, vermiculite and mica. Propylene polymerizations were carried out using those catalysts and the properties of the obtained materials were analyzed using techniques of thermogravimetric analysis X-ray diffraction, dynamic mechanical thermal analysis e scanning electronic microscopy. Results showed the production of nanocomposites with higher thermal degradation temperature. (author)

Preparation and characterization of PbO{sub 2} electrode and its application in electro-catalytic degradation of o-aminophenol in aqueous solution assisted by CuO–Ce{sub 2}O{sub 3}/γ-Al{sub 2}O{sub 3} catalyst

Energy Technology Data Exchange (ETDEWEB)

Chen, Fengtao, E-mail: cft0923@163.com; Yu, Sanchuan; Dong, Xiaoping; Zhang, Ling; Wu, Qiangfang

2013-09-15

Highlights: • A detailed preparation technology of PbO{sub 2} electrode was elucidated. • Fluorescence technique was employed to examine the hydroxyl radicals generated. • o-Aminophenol wastewater was degraded efficiently by electro-catalysis process. • The hypothetical mechanism of electro-catalytic degradation was proposed. -- Abstract: The electrochemical degradation of o-aminophenol (OAP) in aqueous solution was investigated by galvanostatic electrolysis using PbO{sub 2} electrode as anode. The Ti/SnO{sub 2}–Sb{sub 2}O{sub 3}/PbO{sub 2} anode was prepared by thermal decomposition and electro-deposition method, and was characterized by X-ray diffraction (XRD). The hydroxyl radicals electro-generated on anode were detected by fluorescence spectroscopy. The effects of initial pH and current density on the efficiency of the electrochemical degradation process were also studied. UV spectroscopy and chemical oxygen demand (COD) measurements were conducted to evaluate the removal effects of organic pollutants. The experimental results showed that the refractory organics in wastewater can be removed by pure electrochemical process, COD removal efficiency of 91.6% was obtained in 70 min at initial pH 11.0 and current density was equal to 50 mA cm{sup −2}. In order to improve the efficiency of degradation and accelerate the reaction rate, a novel catalyst, γ-Al{sub 2}O{sub 3} supported Ce-doped CuO, was synthesized by impregnating process and was characterized by X-ray photoelectron spectroscopy (XPS). The catalyst exhibited excellent catalytic activity in the electro-catalytic degradation of OAP wastewater and the COD removal efficiency of 91.7% was obtained in 20 min under mild conditions. Finally, a hypothetical mechanism of electro-catalytic degradation was proposed.

Direct synthesis of few-layer graphene supported platinum nanocatalyst for methanol oxidation

Science.gov (United States)

Tan, Hong; Ma, Xiaohui; Sheng, Leimei; An, Kang; Yu, Liming; Zhao, Hongbin; Xu, Jiaqiang; Ren, Wei; Zhao, Xinluo

2014-11-01

High-crystalline few-layer graphene supported Pt nanoparticles have been synthesized by arc discharge evaporation of carbon electrodes containing Pt element. A high-temperature treatment under hydrogen atmosphere has been carried out to obtain a new type of Pt/graphene catalyst for methanol oxidation in direct methanol fuel cell. The morphology and structure characterizations of as-grown few-layer graphene supported Pt nanoparticles and Pt/graphene catalysts have been studied by Raman spectroscopy, scanning electron microscopy with energy-dispersive spectroscopy, and high-resolution transmission electron microscopy. Cyclic voltammograms and chronoamperometric curves show that our present Pt/graphene catalysts have larger current density for methanol oxidation, higher tolerance to carbon monoxide poisoning, and better stability during the operating procedure, compared to commercial Pt/C catalysts.

Enhanced hydrothermal stability of Cu-ZSM-5 catalyst via surface modification in the selective catalytic reduction of NO with NH{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Tao; Shi, Juan; Liu, Jian, E-mail: liujian@cup.edu.cn; Wang, Daxi; Zhao, Zhen, E-mail: zhenzhao@cup.edu.cn; Cheng, Kai; Li, Jianmei

2016-07-01

Highlights: • The hydrothermal stability of Cu-ZSM-5 catalyst was enhanced after surface modification. • An inert silica layer was deposited on the surface of Cu-ZSM-5 and formed a protective layer. • The contact between Si and Cu and Al atoms could form Si-O-Al and Si- O−Cu bonds. • The redox and acidity properties of Cu-ZSM-5-CLD-Aged catalyst were largely retained. • The adsorption and activation of NO and NH{sub 3} was almost unchanged over Cu-ZSM-5-CLD catalyst before and after hydrothermal treatment. - Abstract: The surface of Cu-ZSM-5 catalyst was modified by chemical liquid deposition (CLD) of tetraethoxysilane (TEOS) for enhancing its hydrothermal stability in the selective catalytic reduction of NO with NH{sub 3}. After hydrothermal aging at 750 °C for 13 h, the catalytic performance of Cu-ZSM-5-Aged catalyst was significantly reduced for NO reduction in the entire temperature range, while that of Cu-ZSM-5-CLD-Aged catalyst was affected very little. The characterization results indicated that an inert silica layer was deposited on the surface of Cu-ZSM-5 and formed a protective layer, which prevents the detachment of Cu{sup 2+} from ZSM-5 ion-exchange positions and the dealumination of zeolite during the hydrothermal aging process. Based on the data it is hypothesized to be the primary reason for the high hydrothermal stability of Cu-ZSM-5-CLD catalyst.

Layer-by-Layer Self-Assembled Metal-Ion- (Ag-, Co-, Ni-, and Pd- Doped TiO2 Nanoparticles: Synthesis, Characterisation, and Visible Light Degradation of Rhodamine B

Directory of Open Access Journals (Sweden)

Mphilisi M. Mahlambi

2012-01-01

Full Text Available Metal-ion- (Ag, Co, Ni and Pd doped titania nanocatalysts were successfully deposited on glass slides by layer-by-layer (LbL self-assembly technique using a poly(styrene sulfonate sodium salt (PSS and poly(allylamine hydrochloride (PAH polyelectrolyte system. Solid diffuse reflectance (SDR studies showed a linear increase in absorbance at 416 nm with increase in the number of m-TiO2 thin films. The LbL assembled thin films were tested for their photocatalytic activity through the degradation of Rhodamine B under visible-light illumination. From the scanning electron microscope (SEM, the thin films had a porous morphology and the atomic force microscope (AFM studies showed “rough” surfaces. The porous and rough surface morphology resulted in high surface areas hence the high photocatalytic degradation (up to 97% over a 6.5 h irradiation period using visible-light observed. Increasing the number of multilayers deposited on the glass slides resulted in increased film thickness and an increased rate of photodegradation due to increase in the availability of more nanocatalysts (more sites for photodegradation. The LbL assembled thin films had strong adhesion properties which made them highly stable thus displaying the same efficiencies after five (5 reusability cycles.

Modification of porosity in the catalyst layer of membrane electrode assemblies using pore-forming agents; Modificacion de la porosidad en la capa catalitica de ensambles membrana-electrodo empleando agentes formadores de poros

Energy Technology Data Exchange (ETDEWEB)

Flores Hernandez, J. Roberto [Instituto de Investigaciones Electricas Cuernavaca, Morelos (Mexico)] e-mail: jrflores@iie.org.mx; Reyes, Brenda [UNAM. Facultad de Quimica, Mexico D.F. (Mexico); Barbosa P., Romeli [Centro de Investigacion en Energia, UNAM, Temixco, Morelos (Mexico); Cano Castillo, Ulises; Albarran, Lorena [Instituto de Investigaciones Electricas Cuernavaca, Morelos (Mexico)

2009-09-15

Membrane electrode assemblies (MEA) are the most important part of PEM fuel cells since their interface results in the electrochemical reactions that make the generation of electricity possible. The MEA is composed of a proton exchange membrane, both sides of which are impregnated with a catalyst layer, normally of carbon-supported platinum. Depending on the technique used for its fabrication (atomization, serigraphy, brush methods, chemical reduction, etc.), the properties of the MEA can be different in terms of porosity, distribution of the catalyst, thickness and structure of the catalyst layer, and the quality of the union between the catalyst layer and the membrane, etc. Currently, the porosity of the electrodes is generated by isopropanol evaporation (solvent used in the dye) during the fabrication process conducted in the Instituto de Investigaciones Electricas (IIE). This document presents the results obtained from adding a porous agent to the catalytic dye base composition used in the fabrication of MEA at the IIE. [Spanish] Los Ensambles Membrana-Electrodo (MEA's) son la parte mas importante en las celdas de combustibles tipo PEM, ya que en su interfaz se llevan a cabo las reacciones electroquimicas que hacen posible la generacion de electricidad. El MEA esta compuesto de una membrana de intercambio protonico a la cual se le impregna en ambos lados una capa catalitica normalmente de platino soportado en carbon. Dependiendo de la tecnica empleada en su fabricacion (atomizado, serigrafia, brocha, reduccion quimica, etc.), las propiedades del MEA pueden ser diferentes en cuanto a porosidad, distribucion del catalizador, grosor y estructura de la capa catalitica, asi como la calidad de la union entre la capa catalizadora y la membrana, etc. Actualmente, la porosidad de los electrodos es generada por la evaporacion del isopropanol (solvente utilizado en la tinta) durante el proceso de fabricacion que se realiza en el Instituto de Investigaciones

Effect of reverse Boudouard reaction catalyst on the performance of solid oxide carbon fuel cells integrated with a dry gasifier

International Nuclear Information System (INIS)

Kim, Sun-Kyung; Mehran, Muhammad Taqi; Mushtaq, Usman; Lim, Tak-Hyoung; Lee, Jong-Won; Lee, Seung-Bok; Park, Seok-Joo; Song, Rak-Hyun

2016-01-01

Highlights: • The addition of K_2CO_3 catalyst in carbon fuel improves the performance of SO-CFC. • Thermal and electrochemical analyses done to elucidate the catalytic enhancement. • Material characterization of SO-CFC performed after long-term degradation test. - Abstract: A solid oxide carbon fuel cell (SO-CFC) integrated with a dry gasifier was operated on activated carbon fuel and the effect of adding a reverse Boudouard gasification catalyst on the performance and long-term operation characteristics of the SO-CFC was investigated. The reactivity of the carbon fuels for the Boudouard gasification reaction was analyzed by a thermal analysis at various operating conditions. The SO-CFC was then operated on gasified fuel gas consisting of CO_2 and CO obtained from the integrated dry gasifier. The SO-CFC operated on activated carbon fuel with 5 wt.% K_2CO_3 achieved a maximum power density of 202, 262, and 271 mW/cm"2 at 750, 800, and 850 °C, respectively; the SO-CFC fueled with activated carbon fuel without a catalyst meanwhile yielded maximum power density of 168 mW/cm"2 at 850 °C. By using electrochemical impedance spectroscopy, the effect of adding the catalyst on the gasification products and subsequently on the performance of the SO-CFC was studied. A long-term degradation test was conducted by continuously operating the SO-CFC at 50 mA/cm"2 for 518 h at 750 °C. During the long-term degradation test, the average degradation rate of the SO-CFC was found to be 183 mV/kh. The post-mortem SEM and XRD analyses of the SO-CFC after the long-term test revealed the presence of carbon deposits and oxidation of Ni at the anode, causing a relatively higher degree of degradation in the SO-CFC integrated with the dry gasifier during the long-term operation. The addition of the K_2CO_3 based dry gasification catalyst significantly enhances the performance of the SO-CFC integrated with dry gasification, but during long-term operation, the degradation rate is found

Photocatalyzed degradation of flumequine by doped TiO2 and simulated solar light

International Nuclear Information System (INIS)

Nieto, J.; Freer, J.; Contreras, D.; Candal, R.J.; Sileo, E.E.; Mansilla, H.D.

2008-01-01

Titanium dioxide was obtained in its pure form (TiO 2 ) and in the presence of urea (u-TiO 2 ) and thiourea (t-TiO 2 ) using the sol-gel technique. The obtained powders were characterized by BET surface area analysis, Infrared Spectroscopy, Diffuse Reflectance Spectroscopy and the Rietveld refinement of XRD measurements. All the prepared catalysts show high anatase content (>99%). The a and b-cell parameters of anatase increase in the order TiO 2 2 2 , while the c-parameter presents the opposite trend. Because of the interplay in cell dimensions, the cell grows thicker and shorter when prepared in the presence of urea and thiourea, respectively. The cell volume decreases in the order t-TiO 2 > u-TiO 2 > TiO 2 . The photocatalytic activities of the samples were determined on flumequine under solar-simulated irradiation. The most active catalysts were u-TiO 2 and t-TiO 2 , reaching values over 90% of flumequine degradation after 15 min irradiation, compared with values of 55% for the pure TiO 2 catalyst. Changing simultaneously the catalyst amount (t-TiO 2 ) and pH, multivariate analysis using the response surface methodology was used to determine the roughly optimal conditions for flumequine degradation. The optimized conditions found were pH below 7 and a catalyst amount of 1.6 g L -1

Synthesis, characterization and application of two-dimensional layered metal hydroxides for environmental remediation purposes

Science.gov (United States)

Machingauta, Cleopas

Two-dimensional layered nano composites, which include layered double hydroxides (LDHs), hydroxy double salts (HDSs) and layered hydroxide salts (LHSs) are able to intercalate different molecular species within their gallery space. These materials have a tunable structural composition which has made them applicable as fire retardants, adsorbents, catalysts, catalyst support materials, and ion exchangers. Thermal treatment of these materials results in destruction of the layers and formation of mixed metal oxides (MMOs) and spinels. MMOs have the ability to adsorb anions from solution and may also regenerate layered structures through a phenomenon known as memory effect. Zinc-nickel hydroxy nitrate was used for the uptake of a series of halogenated acetates (HAs). HAs are pollutants introduced into water systems as by-products of water chlorination and pesticide degradation; their sequestration from water is thus crucial. Optimization of layered materials for controlled uptake requires an understanding of their ion-exchange kinetics and thermodynamics. Exchange kinetics of these anions was monitored using ex-situ PXRD, UV-vis, HPLC and FTIR. It was revealed that exchange rates and uptake efficiencies are related to electronic spatial extents and the charge on carboxyl-oxygen atoms. In addition, acetate and nitrate-based HDSs were used to explore how altering the hydroxide layer affects uptake of acetate/nitrate ions. Changing the metal identities affects the interaction of the anions with the layers. From FTIR, we observed that nitrates coordinate in a D3h and Cs/C 2v symmetry; the nitrates in D3h symmetry were easily exchangeable. Interlayer hydrogen bonding was also revealed to be dependent on metal identity. Substituting divalent cations with trivalent cations produces materials with a higher charge density than HDSs and LHSs. A comparison of the uptake efficiency of zinc-aluminum, zinc-gallium and zinc-nickel hydroxy nitrates was performed using trichloroacetic

A novel visible light-driven Ag3PO4/SBA-15 nanocomposite: Preparation and application in the photo-degradation of pollutants

International Nuclear Information System (INIS)

Chai, Yuanyuan; Wang, Li; Ren, Jia; Dai, Wei-Lin

2015-01-01

Graphical abstract: - Highlights: • Highly efficient visible-light-driven Ag 3 PO 4 /SBA-15 nanocomposite. • Application in the photo-degradation of RhB. • Synthesis from a facile and simple colloidal method. • 20%-Ag 3 PO 4 /SBA-15 shows 8 times faster degradation rate than Ag 3 PO 4 . • Super stability and recycling ability. - Abstract: A novel visible light-driven environmental-benign Ag 3 PO 4 /SBA-15 nanocomposite photo-catalyst was synthesized for the photo-degradation of pollutants. The exploration on adsorption and photo-catalysis of dye or organic pollution for the nanocomposite was carried out. The adsorption capability for Ag 3 PO 4 /SBA-15 nanocomposite increases by 3 times compared with that of the Ag 3 PO 4 particles. The photo-catalytic activity of nanocomposite is higher than pristine Ag 3 PO 4 nanoparticle for the degradation of RhB or MO under visible light irradiation (λ > 420 nm). The effect of Ag 3 PO 4 loading on the catalytic performance was also studied. The results show that the optimum degradation is achieved over 20% Ag 3 PO 4 /SBA-15. Compared to pure Ag 3 PO 4 nanoparticle, the most efficient catalyst showed 8 times higher photo-catalytic activity for the degradation of RhB. The Ag 3 PO 4 /SBA-15 catalysts were systematically characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV–Vis diffuse reflectance spectroscopy (DRS), and N 2 -adsorption–desorption isotherms (BET). A possible mechanism scheme regarding photo-degradation enhancement induced by dye enrichments has been proposed on the Ag 3 PO 4 /SBA-15 nanocomposite. Additionally, the SBA-15 support can enhance the efficiency of separation of catalyst from the reaction mixture, implying that the Ag 3 PO 4 loading on the SBA-15 catalyst will not result in the extra environment and health problems and reduce the cost of wastewater treatment

Solar photocatalytic degradation of isoproturon over TiO2/H-MOR composite systems

International Nuclear Information System (INIS)

Sharma, Mangalampalli V. Phanikrishna; Durgakumari, Valluri; Subrahmanyam, Machiraju

2008-01-01

The photocatalytic degradation and mineralization of isoproturon herbicide was investigated in aqueous solution containing TiO 2 over H-mordenite (H-MOR) photocatalysts under solar light. The catalysts are characterized by X-ray diffraction (XRD), UV-Vis diffused reflectance spectra (UV-Vis DRS), Fourier transform-infra red spectra (FT-IR) and scanning electron microscopy (SEM) techniques. The effect of TiO 2 , H-MOR support and different wt% of TiO 2 over the support on the photocatalytic degradation and influence of parameters such as TiO 2 loading, catalyst amount, pH and initial concentration of isoproturon on degradation are evaluated. 15 wt% TiO 2 /H-MOR composite is found to be optimum. The degradation reaction follows pseudo-first order kinetics and is discussed in terms of Langmuir-Hinshelwood (L-H) kinetic model. The extent of isoproturon mineralization studied with chemical oxygen demand (COD) and total organic carbon (TOC) measurements and ∼80% mineralization occurred in 5 h. A plausible mechanism is proposed based on the intermediates identified by liquid chromatography-mass spectroscopy (LC-MS)

Solar photocatalytic degradation of isoproturon over TiO2/H-MOR composite systems.

Science.gov (United States)

Sharma, Mangalampalli V Phanikrishna; Durgakumari, Valluri; Subrahmanyam, Machiraju

2008-12-30

The photocatalytic degradation and mineralization of isoproturon herbicide was investigated in aqueous solution containing TiO2 over H-mordenite (H-MOR) photocatalysts under solar light. The catalysts are characterized by X-ray diffraction (XRD), UV-Vis diffused reflectance spectra (UV-Vis DRS), Fourier transform-infra red spectra (FT-IR) and scanning electron microscopy (SEM) techniques. The effect of TiO2, H-MOR support and different wt% of TiO2 over the support on the photocatalytic degradation and influence of parameters such as TiO2 loading, catalyst amount, pH and initial concentration of isoproturon on degradation are evaluated. 15wt% TiO2/H-MOR composite is found to be optimum. The degradation reaction follows pseudo-first order kinetics and is discussed in terms of Langmuir-Hinshelwood (L-H) kinetic model. The extent of isoproturon mineralization studied with chemical oxygen demand (COD) and total organic carbon (TOC) measurements and approximately 80% mineralization occurred in 5h. A plausible mechanism is proposed based on the intermediates identified by liquid chromatography-mass spectroscopy (LC-MS).

Enhanced MEA Performance for PEMFCs under Low Relative Humidity and Low Oxygen Content Conditions via Catalyst Functionalization

Energy Technology Data Exchange (ETDEWEB)

Xin, Le; Yang, Fan; Xie, Jian; Yang, Zhiwei; Kariuki, Nancy N.; Myers, Deborah J.; Peng, Jui-Kun; Wang, Xiaohua; Ahluwalia, Rajesh K.; Yu, Kang; Ferreira, Paulo J.; Bonastre, Alex Martinez; Fongalland, Dash; Sharman, Jonathan

2017-01-01

This work demonstrates that functionalizing annealed-Pt/Ketjen black EC300j (a-Pt/KB) and dealloyed-PtNi/Ketjen black EC300j (d-PtNi/KB) catalysts using p-phenyl sulfonic acid can effectively enhance performance in the membrane electrode assemblies (MEAs) of proton exchange membrane fuel cells (PEMFCs). The functionalization increased the size of both Pt and PtNi catalyst particles and resulted in the further leaching of Ni from the PtNi catalyst while promoting the formation of nanoporous PtNi nanoparticles. The size of the SO3H-Pt/KB and SO3H-PtNi/KB carbon-based aggregates decreased dramatically, leading to the formation of catalyst layers with narrower pore size distributions.MEA tests highlighted the benefits of the surface functionalization, in which the cells with SO3H-Pt/KB and SO3H-PtNi/KB cathode catalysts showed superior high current density performance under reduced RH conditions, in comparison with cells containing annealed Pt/KB (a-Pt/KB) and de-alloyed PtNi/KB (d-PtNi/KB) catalysts. The performance improvement was particularly evident when using reactant gases with low relative humidity, indicating that the hydrophilic functional groups on the carbon improved the water retention in the cathode catalyst layer. These results show a new avenue for enhancing catalyst performance for the next generation of catalytic materials for PEMFCs.

Cu-MCM-41 nanoparticles: An efficient catalyst for the synthesis of 5 ...

Indian Academy of Sciences (India)

To investigate reusability, the catalyst was recovered by simple filtration and reused for several cycles with consistent activity. Keywords. ... membranes. Another advantage of tetrazolic acids over carboxylic acids is that they are resistant to many bio- logical metabolic degradation pathways.3. Conventionally 5-substituted ...

Rapid degradation of Congo red by molecularly imprinted polypyrrole-coated magnetic TiO{sub 2} nanoparticles in dark at ambient conditions

Energy Technology Data Exchange (ETDEWEB)

Wei, Shoutai; Hu, Xiaolei; Liu, Hualong; Wang, Qiang; He, Chiyang, E-mail: chiyanghe@hotmail.com

2015-08-30

Highlights: • Molecularly imprinted polypyrrole-coated magnetic TiO{sub 2} catalyst was prepared. • The catalyst degraded Congo red rapidly in dark at ambient conditions. • Degradation mechanism was proposed according to LC–MS analysis. • The catalyst can be easily recycled by a magnet. - Abstract: A novel molecularly imprinted polymer (MIP)-coated magnetic TiO{sub 2} nanocomposite was prepared, using methyl orange (MO) as the dummy template and pyrrole as functional monomer, for degradation of Congo red (CR). The nanocomposite was characterized by Fourier transform infrared spectroscopy, thermo-gravimetric analysis, X-ray diffraction, transmission electron microscopy, and vibrating sample magnetometer. The imprinting efficiency of the imprinted nanoparticles was investigated by static binding test, and their degradation ability toward CR was also studied. Moreover, the effects of pH, temperature, dissolved oxygen and oscillation rate on degradation rate of CR were investigated. Results showed that the imprinted nanocomposite had higher adsorption ability for MO compared with the non-imprinted one. Moreover, it could degrade CR rapidly in dark at room temperature and atmospheric pressure and could be recycled easily by a magnet with a good reusability. A degradation mechanism was proposed according to LC–MS analysis of degradation products of CR. The new imprinted nanoparticles showed high catalytic activity at ambient conditions without light illumination and additional chemicals, and therefore, it can be potentially applied to the rapid, “green” and low-cost degradation of CR in industrial printing and dyeing wastewater.

Urea thermolysis and NOx reduction with and without SCR catalysts

International Nuclear Information System (INIS)

Fang, Howard L.; DaCosta, Herbert F.M.

2003-01-01

Urea-selective catalytic reduction (SCR) has been a leading contender for removal of nitrogen oxides (deNO x ) from diesel engine emissions. Despite its advantages, the SCR technology faces some critical detriments to its catalytic performance such as catalyst surface passivation (caused by deposit formation) and consequent stoichiometric imbalance of the urea consumption. Deposit formation deactivates catalytic performance by not only consuming part of the ammonia produced during urea decomposition but also degrading the structural and thermal properties of the catalyst surface. We have characterized the urea thermolysis with and without the urea-SCR catalyst using both spectroscopic (DRIFTS and Raman) and thermal techniques (thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC)) to identify the deposit components and their corresponding thermal properties. Urea thermolysis exhibits two decomposition stages, involving ammonia generation and consumption, respectively. The decomposition after the second stage leads to the product of melamine complexes, (HNC=NH) x (HNCO) y , that hinder catalytic performance. The presence of catalyst accompanied with a good spray of the urea solution helps to eliminate the second stage. In this work, kinetics of the direct reduction of NO x by urea is determined and the possibility of using additives to the urea solution in order to rejuvenate the catalyst surface and improve its performance will be discussed

Photocatalytic degradation of phenol by iodine doped tin oxide nanoparticles under UV and sunlight irradiation

Energy Technology Data Exchange (ETDEWEB)

Al-Hamdi, Abdullah M.; Sillanpää, Mika [Laboratory of Green Chemistry, Lappeenranta University of Technology, Sammonkatu 12, 50130 Mikkeli (Finland); Dutta, Joydeep, E-mail: dutta@squ.edu.om [Chair in Nanotechnology, Water Research Center, Sultan Qaboos University, P.O. Box 17, 123 Al-Khoudh (Oman)

2015-01-05

Highlights: • A sol–gel method used to synthesize tin oxide nanoparticles. • Nanoparticles of tin oxide doped with different iodine concentrations. • Degradation studies carried up with UV–vis, TOC, HPLC and GC instruments. • 1% iodine doped tin dioxide showed maximum photodegradation efficiency. - Abstract: Iodine doped tin oxide (SnO{sub 2}:I) nanoparticles were prepared by sol–gel synthesis and their photocatalytic activities with phenol as a test contaminant were studied. In the presence of the catalysts, phenol degradation under direct sunlight was comparable to what was achieved under laboratory conditions. Photocatalytic oxidation reactions were studied by varying the catalyst loading, light intensity, illumination time, pH of the reactant and phenol concentration. Upon UV irradiation in the presence of SnO{sub 2}:I nanoparticles, phenol degrades very rapidly within 30 min, forming carboxylic acid which turns the solution acidic. Phenol degradation rate with 1% iodine doped SnO{sub 2} nanoparticles is at least an order of magnitude higher compared to the degradation achieved through undoped SnO{sub 2} nanoparticles under similar illumination conditions.

Photocatalytic degradation of phenol by iodine doped tin oxide nanoparticles under UV and sunlight irradiation

International Nuclear Information System (INIS)

Al-Hamdi, Abdullah M.; Sillanpää, Mika; Dutta, Joydeep

2015-01-01

Highlights: • A sol–gel method used to synthesize tin oxide nanoparticles. • Nanoparticles of tin oxide doped with different iodine concentrations. • Degradation studies carried up with UV–vis, TOC, HPLC and GC instruments. • 1% iodine doped tin dioxide showed maximum photodegradation efficiency. - Abstract: Iodine doped tin oxide (SnO 2 :I) nanoparticles were prepared by sol–gel synthesis and their photocatalytic activities with phenol as a test contaminant were studied. In the presence of the catalysts, phenol degradation under direct sunlight was comparable to what was achieved under laboratory conditions. Photocatalytic oxidation reactions were studied by varying the catalyst loading, light intensity, illumination time, pH of the reactant and phenol concentration. Upon UV irradiation in the presence of SnO 2 :I nanoparticles, phenol degrades very rapidly within 30 min, forming carboxylic acid which turns the solution acidic. Phenol degradation rate with 1% iodine doped SnO 2 nanoparticles is at least an order of magnitude higher compared to the degradation achieved through undoped SnO 2 nanoparticles under similar illumination conditions

Activation of peroxymonosulfate by graphitic carbon nitride loaded on activated carbon for organic pollutants degradation

Energy Technology Data Exchange (ETDEWEB)

Wei, Mingyu; Gao, Long; Li, Jun [School of Environmental Engineering, Wuhan Textile University, Wuhan 430073 (China); Fang, Jia [School of Chemistry and Chemical Engineering, Wuhan Textile University, Wuhan 430073 (China); Cai, Wenxuan [School of Environmental Engineering, Wuhan Textile University, Wuhan 430073 (China); Li, Xiaoxia [School of Chemistry and Chemical Engineering, Wuhan Textile University, Wuhan 430073 (China); Xu, Aihua, E-mail: xahspinel@sina.com [School of Environmental Engineering, Wuhan Textile University, Wuhan 430073 (China); Engineering Research Center for Clean Production of Textile Dyeing and Printing, Ministry of Education, Wuhan 430073 (China)

2016-10-05

Highlights: • Supported g-C{sub 3}N{sub 4} on AC catalysts with different loadings were prepared. • The metal free catalysts exhibited high efficiency for dyes degradation with PMS. • The catalyst presented a long-term stability for multiple runs. • The C=O groups played a key role in the oxidation process. - Abstract: Graphitic carbon nitride supported on activated carbon (g-C{sub 3}N{sub 4}/AC) was prepared through an in situ thermal approach and used as a metal free catalyst for pollutants degradation in the presence of peroxymonosulfate (PMS) without light irradiation. It was found that g-C{sub 3}N{sub 4} was highly dispersed on the surface of AC with the increase of surface area and the exposition of more edges and defects. The much easier oxidation of C species in g-C{sub 3}N{sub 4} to C=O was also observed from XPS spectra. Acid Orange 7 (AO7) and other organic pollutants could be completely degraded by the g-C{sub 3}N{sub 4}/AC catalyst within 20 min with PMS, while g-C{sub 3}N{sub 4}+PMS and AC+PMS showed no significant activity for the reaction. The performance of the catalyst was significantly influenced by the amount of g-C{sub 3}N{sub 4} loaded on AC; but was nearly not affected by the initial solution pH and reaction temperature. In addition, the catalysts presented good stability. A nonradical mechanism accompanied by radical generation (HO· and SO{sub 4}·{sup −}) in AO7 oxidation was proposed in the system. The C=O groups play a key role in the process; while the exposure of more N-(C){sub 3} group can further increase its electron density and basicity. This study can contribute to the development of green materials for sustainable remediation of aqueous organic pollutants.

Phenol degradation catalyzed by a peroxidase mimic constructed through the grafting of heme onto metal-organic frameworks.

Science.gov (United States)

Jiang, Wei; Yang, Jiebing; Wang, Xinghuo; Han, Haobo; Yang, Yan; Tang, Jun; Li, Quanshun

2018-01-01

The aim of this work was to construct a peroxidase mimic for achieving the phenol degradation through Fenton reaction. The enzyme mimic was synthesized through the conjugation of heme with the amino group of 2-amino-1,4-benzene dicarboxylate in UiO-66-NH 2 (ZrMOF), namely Heme-ZrMOF. Compared to free heme, the composite Heme-ZrMOF exhibited an obviously enhanced ability for phenol degradation with up to 97.3% of phenol removal after 2h. Meanwhile, it could achieve the easy separation of catalyst from the system and the elimination of iron residues in the process of phenol degradation. Finally, the catalyst Heme-ZrMOF was observed to possess good recyclability in the phenol degradation with still 76.2% of phenol removal after 4 cycles. Copyright © 2017 Elsevier Ltd. All rights reserved.

Degradation behavior of polymer blend of isotactic polypropylenes with and without unsaturated chain end group

International Nuclear Information System (INIS)

Nakatani, Hisayuki; Kurniawan, Dodik; Taniike, Toshiaki; Terano, Minoru

2008-01-01

In this work, the relationship between the unsaturated chain end group content and the thermal oxidative degradation rate was systematically studied with binary polymer blends of isotactic polypropylene (iPP) with and without the unsaturated chain end group. The iPPs with and without the unsaturated chain end group were synthesized by a metallocene catalyst in the absence of hydrogen and by a Ziegler catalyst in the presence of one, respectively. The thermal oxidative degradation rate of the binary iPP blends was estimated from the molecular weight and the apparent activation energy (ΔE), which were obtained through size exclusion chromatography (SEC) and thermogravimetric analysis (TGA) measurements, respectively. These values exhibited a negative correlation against the mole content of the unsaturated chain end group. The thermal oxidative degradation rate apparently depends on the content of the unsaturated chain end group. This tendency suggests that the unsaturated chain end acts as a radical initiator of the iPP degradation reaction.

Catalyst displacement assay: a supramolecular approach for the design of smart latent catalysts for pollutant monitoring and removal† †Electronic supplementary information (ESI) available. See DOI: 10.1039/c6sc05584b Click here for additional data file.

Science.gov (United States)

Ho, Pui-Yu; Lu, Yu-Jing; Tang, Qian

2017-01-01

Latent catalysts can be tuned to function smartly by assigning a sensing threshold using the displacement approach for targeted analytes. Three cyano-bridged bimetallic complexes were synthesized as “smart” latent catalysts through the supramolecular assembly of different metallic donors [FeII(CN)6]4–, [FeII(tBubpy)(CN)4]2–, and FeII(tBubpy)2(CN)2 with a metallic acceptor [CuII(dien)]2+. The investigation of both their thermodynamic and kinetic properties on binding with toxic pollutants provided insight into their smart off–on catalytic capabilities, enabling us to establish a threshold-controlled catalytic system for the degradation of pollutants such as cyanide and oxalate. With these smart latent catalysts, a new catalyst displacement assay (CDA) was demonstrated and applied in a real wastewater treatment process to degrade cyanide pollutants in both domestic (level I, untreated) and industrial wastewater samples collected in Hong Kong, China. The smart system was adjusted to be able to initiate the catalytic oxidation of cyanide at a threshold concentration of 20 μM (the World Health Organization’s suggested maximum allowable level for cyanide in wastewater) to the less harmful cyanate under ambient conditions. PMID:28580114

Heterogeneous catalytic ozonation of ciprofloxacin in water with carbon nanotube supported manganese oxides as catalyst

Energy Technology Data Exchange (ETDEWEB)

Sui, Minghao, E-mail: suiminghao.sui@gmail.com [State Key Laboratory of Pollution Control and Resource Reuse, School of Environmental Science and Engineering, Tongji University, 1239 Siping Road, Shanghai 200092 (China); Xing, Sichu; Sheng, Li; Huang, Shuhang; Guo, Hongguang [State Key Laboratory of Pollution Control and Resource Reuse, School of Environmental Science and Engineering, Tongji University, 1239 Siping Road, Shanghai 200092 (China)

2012-08-15

Highlights: Black-Right-Pointing-Pointer Ciprofloxacin in water was degraded by heterogeneous catalytic ozonation. Black-Right-Pointing-Pointer MnOx were supported on MWCNTs to serve as catalyst for ozonation. Black-Right-Pointing-Pointer MnOx/MWCNT exhibited highly catalytic activity on ozonation of ciprofloxacin in water. Black-Right-Pointing-Pointer MnOx/MWCNT resulted in effective antibacterial activity inhibition on ciprofloxacin. Black-Right-Pointing-Pointer MnOx/MWCNT promoted the generation of hydroxyl radicals. - Abstract: Carbon nanotube-supported manganese oxides (MnOx/MWCNT) were used as catalysts to assist ozone in degrading ciprofloxacin in water. Manganese oxides were successfully loaded on multi-walled carbon nanotube surfaces by simply impregnating the carbon nanotube with permanganate solution. The catalytic activities of MnOx/MWCNT in ciprofloxacin ozonation, including degradation, mineralization effectiveness, and antibacterial activity change, were investigated. The presence of MnOx/MWCNT significantly elevated the degradation and mineralization efficiency of ozone on ciprofloxacin. The microbiological assay with a reference Escherichia coli strain indicated that ozonation with MnOx/MWCNT results in more effective antibacterial activity inhibition of ciprofloxacin than that in ozonation alone. The effects of catalyst dose, initial ciprofloxacin concentration, and initial pH conditions on ciprofloxacin ozonation with MnOx/MWCNT were surveyed. Electron spin resonance trapping was applied to assess the role of MnOx/MWCNT in generating hydroxyl radicals (HO{center_dot}) during ozonation. Stronger 5,5-dimethyl-1-pyrroline-N-oxide-OH signals were observed in the ozonation with MnOx/MWCNT compared with those in ozonation alone, indicating that MnOx/MWCNT promoted the generation of hydroxyl radicals. The degradation of ciprofloxacin was studied in drinking water and wastewater process samples to gauge the potential effects of water background matrix on

High aspect ratio catalytic reactor and catalyst inserts therefor

Science.gov (United States)

Lin, Jiefeng; Kelly, Sean M.

2018-04-10

The present invention relates to high efficient tubular catalytic steam reforming reactor configured from about 0.2 inch to about 2 inch inside diameter high temperature metal alloy tube or pipe and loaded with a plurality of rolled catalyst inserts comprising metallic monoliths. The catalyst insert substrate is formed from a single metal foil without a central supporting structure in the form of a spiral monolith. The single metal foil is treated to have 3-dimensional surface features that provide mechanical support and establish open gas channels between each of the rolled layers. This unique geometry accelerates gas mixing and heat transfer and provides a high catalytic active surface area. The small diameter, high aspect ratio tubular catalytic steam reforming reactors loaded with rolled catalyst inserts can be arranged in a multi-pass non-vertical parallel configuration thermally coupled with a heat source to carry out steam reforming of hydrocarbon-containing feeds. The rolled catalyst inserts are self-supported on the reactor wall and enable efficient heat transfer from the reactor wall to the reactor interior, and lower pressure drop than known particulate catalysts. The heat source can be oxygen transport membrane reactors.

Evaluation of photocatalytic activities of supported catalysts on NaX zeolite or activated charcoal

Energy Technology Data Exchange (ETDEWEB)

Brites-Nóbrega, Fernanda F. de [Chemical Engineering Department, Universidade Estadual de Maringá (UEM), Av. Colombo, 5790, CEP 87020-900 Maringá, PR (Brazil); Sanitary and Environmental Engineering Department, Universidade Federal de Minas Gerais (UFMG), Av. Antônio Carlos, 6627, Campus Pampulha, Belo Horizonte, MG (Brazil); Polo, Aldino N.B.; Benedetti, Angélica M. [Chemical Engineering Department, Universidade Estadual do Oeste do Paraná (UNIOESTE), Rua da Faculdade, 645, CEP 85903-000 Toledo, PR (Brazil); Leão, Mônica M.D. [Sanitary and Environmental Engineering Department, Universidade Federal de Minas Gerais (UFMG), Av. Antônio Carlos, 6627, Campus Pampulha, Belo Horizonte, MG (Brazil); Slusarski-Santana, Veronice, E-mail: veronice.santana@unioeste.br [Chemical Engineering Department, Universidade Estadual do Oeste do Paraná (UNIOESTE), Rua da Faculdade, 645, CEP 85903-000 Toledo, PR (Brazil); Fernandes-Machado, Nádia R.C. [Chemical Engineering Department, Universidade Estadual de Maringá (UEM), Av. Colombo, 5790, CEP 87020-900 Maringá, PR (Brazil)

2013-12-15

Highlights: • The synergic effect between ZnO and NaX was positive, which increased its activity. • The best results were obtained at pH 3 and 9 with ZnO/NaX and at pH 3 with Nb{sub 2}O{sub 5}/AC. • High degradation and considerable mineralization were attained with 10% ZnO/NaX. • ZnO and Nb{sub 2}O{sub 5} supported on NaX and AC are promising alternatives as photocatalysts. -- Abstract: This study aimed to evaluate the photocatalytic activity of ZnO and Nb{sub 2}O{sub 5} catalysts, both supported on NaX zeolite and activated charcoal (AC). The synergistic effect between oxide and support and the influence of solution pH (3, 7 and 9) on photocatalytic degradation of reactive blue 5G (C.I. 222) were analyzed. The catalysts Nb{sub 2}O{sub 5}/NaX, Nb{sub 2}O{sub 5}/AC and ZnO/NaX, ZnO/AC with 5 and 10% (wt%) were prepared by wet impregnation. The results showed that the catalysts exhibit quite different structural and textural properties. The synergic effect between ZnO and NaX support was higher than that with the activated charcoal, showing that these catalysts were more efficient. The most photoactive catalyst was 10% ZnO/NaX which showed 100% discoloration of the dye solution at pH 3, 7 and 9 after 0.5, 5 and 2 h of irradiation, respectively. The hydrolytic nature of zeolite favored the formation of surface hydroxyl radicals, which increased the activity of the photocatalyst. Thus, catalysts supported on NaX zeolite are promising for use in photocatalysis.

3D-modelling of bifunctional core-shell catalysts for the production of fuels from biomass-based synthesis gas

Energy Technology Data Exchange (ETDEWEB)

Ding, Wenjin; Lee, Seung Cheol; Li, Hui; Pfeifer, Peter; Dittmeyer, Roland [Karlsruhe Institute of Technology (KIT), Eggenstein-Leopoldshafen (Germany). Inst. for Micro Process Engineering (IMVT)

2013-09-01

Until now, the main route for the production of DME from synthesis gas in industry is methanol synthesis on a metallic catalyst and subsequent dehydration of methanol on an acid catalyst (two-step process). A single-step process using bifunctional catalysts to perform the two steps simultaneously would be preferred e.g. due to thermodynamic considerations; but this is impeded by the higher volumetric heat release which may cause deactivation of the methanol synthesis catalyst function. Thus we propose to conduct the reaction in a microchannel reactor. However, in order to increase the productivity of the microchannel reactor and to lower the investment costs, we aim at a high selectivity and activity of the catalyst. The continuously removal of methanol by dehydration on an acidic ZSM-5 catalyst as shell improves the thermodynamic conditions of methanol synthesis in the CuO/ZnO/Al{sub 2}O{sub 3} core; thus, the synthesis gas conversion can be higher than that determined by the thermodynamics of pure methanol synthesis. The molecular sieving in the zeolite layer can further lead to higher selectivity of DME at milder reaction conditions. However, mass transport limitation of the synthesis gas to the catalyst core should not hinder the reaction, and therefore a more detailed investigation is required. In order to computer-aided optimize the catalyst structure and the operating conditions for core-shell catalysts, a simulation model should be developed to study the coupled reaction and transport processes in core-shell catalysts. In this simulation model the complicated interaction of diffusion and reaction in the zeolite layer (shell) must be detailed by a network model to describe its structure and the mechanisms effectively. In addition, suitable diffusion and kinetic models are required to describe the mass transport and reactions in the layer. Suitable networks, diffusion and kinetic models are discussed for 3D simulations in this contribution. (orig.)

Discoloration of a red cationic dye by supported TiO{sub 2} photocatalysis

Energy Technology Data Exchange (ETDEWEB)

Mounir, B. [Ecole Superieure de Technologie de Safi, Universite Cadi Ayyad, BP 89, Route Dar Si Aissa, Safi (Morocco); Pons, M.N. [Laboratoire des Sciences du Genie Chimique, CNRS-ENSIC-INPL, 1, rue Grandville, BP 20451, F-54001 Nancy Cedex (France)], E-mail: Marie-Noelle.Pons@ensic.inpl-nancy.fr; Zahraa, O. [Departement de Chimie Physique des Reactions, ENSIC-INPL, 1, rue Grandville, BP 20451, F-54001 Nancy Cedex (France); Yaacoubi, A. [Departement de Chimie, Faculte des Sciences Semlalia, Universite Cadi Ayyad, Boulevard Prince Moulay Abdellah, BP 2390, 40000 Marrakech (Morocco); Benhammou, A. [Laboratoire d' Automatique et d' Etudes des Procedes, Faculte des Sciences Semlalia, Universite Cadi Ayyad, Boulevard Prince Moulay Abdellah, BP 2390, 40000 Marrakech (Morocco)

2007-09-30

The degradation under UV, visible and sunlight irradiation of C.I. Basic Red 46 (BR 46) dye used for acrylic fibers dyeing has been studied in a lab-scale continuous system with two different immobilized TiO{sub 2} systems. Catalyst I was based on TiO{sub 2} particles deposited on cellulose fibers; Catalyst II combined TiO{sub 2} particles deposited on a layer of cellulose fibers (as in Catalyst I) with a layer of carbon fibers and finally a layer of cellulose fibers. The treatment of aqueous dye solutions and industrial wastewater contaminated with the same dye has been evaluated in terms of color removal and chemical oxygen demand (COD) decrease. With UV light, aqueous solutions containing dye were decolorized slightly more rapidly with Catalyst II than with Catalyst I. Sunlight was also very effective and experiments involving sunlight irradiation showed Catalyst II to be the more efficient, giving more than 90% discoloration after 20 min of treatment. Comparing the discoloration yield by adsorption or under visible light for both catalysts, it was observed that the difference between them is below 5%. The adsorption kinetics was found to follow a second-order rate law for Catalyst I and a first-order rate law for Catalyst II. The kinetics of photocatalytic degradation under UV or sunlight were found to follow a first-order rate law for both catalytic systems. Under sunlight the COD removal yield for textile wastewater reaches 33% with Catalyst I against 93% with Catalyst II.

Comparison study of catalyst nanoparticle formation and carbon nanotube growth: Support effect

International Nuclear Information System (INIS)

Wang Yunyu; Luo Zhiquan; Li Bin; Ho, Paul S.; Yao Zhen; Shi Li; Bryan, Eugene N.; Nemanich, Robert J.

2007-01-01

A comparison study has been conducted on the formation of catalyst nanoparticles on a high surface tension metal and low surface tension oxide for carbon nanotube (CNT) growth via catalytic chemical vapor deposition (CCVD). Silicon dioxide (SiO 2 ) and tantalum have been deposited as supporting layers before deposition of a thin layer of iron catalyst. Iron nanoparticles were formed after thermal annealing. It was found that densities, size distributions, and morphologies of iron nanoparticles were distinctly different on the two supporting layers. In particular, iron nanoparticles revealed a Volmer-Weber growth mode on SiO 2 and a Stranski-Krastanov mode on tantalum. CCVD growth of CNTs was conducted on iron/tantalum and iron/SiO 2 . CNT growth on SiO 2 exhibited a tip growth mode with a slow growth rate of less than 100 nm/min. In contrast, the growth on tantalum followed a base growth mode with a fast growth rate exceeding 1 μm/min. For comparison, plasma enhanced CVD was also employed for CNT growth on SiO 2 and showed a base growth mode with a growth rate greater than 2 μm/min. The enhanced CNT growth rate on tantalum was attributed to the morphologies of iron nanoparticles in combination with the presence of an iron wetting layer. The CNT growth mode was affected by the adhesion between the catalyst and support as well as CVD process

Photocatalytic Degradation of Aniline Using TiO2 Nanoparticles in a Vertical Circulating Photocatalytic Reactor

Directory of Open Access Journals (Sweden)

F. Shahrezaei

2012-01-01

Full Text Available Photocatalytic degradation of aniline in the presence of titanium dioxide (TiO2 and ultraviolet (UV illumination was performed in a vertical circulating photocatalytic reactor. The effects of catalyst concentration (0–80 mg/L, initial pH (2–12, temperature (293–323 K, and irradiation time (0–120 min on aniline photodegradation were investigated in order to obtain the optimum operational conditions. The results reveal that the aniline degradation efficiency can be effectively improved by increasing pH from 2 to 12 and temperature from 313 to 323 K. Besides, the effect of temperature on aniline photo degradation was found to be unremarkable in the range of 293–313 K. The optimum catalyst concentration was about 60 mg/L. The Langmuir Hinshelwood kinetic model could successfully elucidate the effects of the catalyst concentration, pH, and temperature on the rate of heterogeneous photooxidation of aniline. The data obtained by applying the Langmuir Hinshelwood treatment are consistent with the available kinetic parameters. The activated energy for the photocatalytic degradation of aniline is 20.337 kj/mol. The possibility of the reactor use in the treatment of a real petroleum refinery wastewater was also investigated. The results of the experiments indicated that it can therefore be potentially applied for the treatment of wastewater contaminated by different organic pollutants.

CATALYTIC WET PEROXIDE OXIDATION OF HYDROQUINONE WITH Co(II)/ACTIVE CARBON CATALYST LOADED IN STATIC BED

Institute of Scientific and Technical Information of China (English)

2008-01-01

Catalysts based on Co(II) supported on active carbon were prepared and loaded in static bed. The hydroquinone would be degraded completely after treated by Catalytic wet peroxide oxidation method with Co(II)/active carbon catalyst. After activate treatment, the active carbon was immerged in cobaltous nitrate solution, then put into a drying oven, Co(II) could be loaded on the micro-surface of carbon. Taking the static bed as the equipment, the absorption of active carbon and catalysis of Co(II) was used to reduce activation energy of hydroquinone. Thus hydroquinone could be drastically degraded and the effluent can be drained under the standard. Referring to Fenton reaction mechanism, experiment had been done to study the heterogeneous catalyzed oxidation mechanism of Co(II). The degradation rate of hydroquinone effluent could be achieved to 92% when treated in four columns at H2O2 concentration 10%, reaction temperature 40℃ , pH 5 and reaction time 2.5h.

Pore-Network Modeling of Water and Vapor Transport in the Micro Porous Layer and Gas Diffusion Layer of a Polymer Electrolyte Fuel Cell

NARCIS (Netherlands)

Qin, C.; Hassanizadeh, S.M.; van Oosterhout, L.M.

2016-01-01

In the cathode side of a polymer electrolyte fuel cell (PEFC), a micro porous layer (MPL) added between the catalyst layer (CL) and the gas diffusion layer (GDL) plays an important role in water management. In this work, by using both quasi-static and dynamic pore-network models, water and vapor

Application of Sonocatalyst and Sonophotocatalyst for Degradation of Acid Red 14 in Aqueous Environment

Directory of Open Access Journals (Sweden)

Aref Shokri

2016-09-01

Full Text Available Background & Aims of the Study: Azo dyes are employed in industrial processes such as textile industry to create large quantities of colored sewages that have organic and non-organic materials. So, remediation of them is essential. In this project, degradation and mineralization of Acid red 14 (AR14 that is a mono Azo dye and widely used in the textile industries was investigated by Sonocatalysis and Sono photo catalyst in the presence of homogeneous (Fe3+ photo catalyst. Materials & Methods: This study is an experimental investigation on a laboratory scale. The study performed on synthetic wastewater that hold Acid red 14.The influence of operational parameters such as initial dye concentration and ultrasonic power on the sonochemical degradation was also studied. The optimization of variables was done by one factor at a time method. Results: The efficiency of the Sonophotocatalytic process with Fe3+ was higher than Sonocatalysis and photo catalyst processes alone. The combination of sonolysis, Fe3+ and  photo catalyst caused a highly synergistic effect and the synergy index obtained for Fe3+ Sono photo catalysis was 2.05. Chemical oxygen demand (COD analysis was used to study the degree of mineralization. After 180 min of reaction, the removal of COD was 15, 25.4 and 55.5% for UV/Fe3+, US/Fe3+ and UV/US/Fe3+ process, respectively. The degradation by photocatalysis and sonolysis followed pseudo first-order with respect to the concentration of AR14. Conclusions: The results showed that the Sono photo catalytic degradation and mineralization of AR14 in the presence of Fe3+ was synergistic, most likely because of the participation of Sono-Fenton and photo-Fenton reactions.

Effects of the gas-liquid ratio on the optimum catalyst quantity for the CECE process with a homogeneously packed LPCE column

International Nuclear Information System (INIS)

Sugiyama, T.; Ushida, A.; Yamamoto, I.

2008-01-01

In order to improve the separative performance of a combined electrolysis catalytic exchange (CECE) process, we have carried out experimental studies on hydrogen isotope separation by a CECE process using a liquid phase catalytic exchange (LPCE) column of trickle-type packed beds. Two types of trickle beds were tested in our previous study. One was the layered bed, where layers of Kogel catalysts and Dixon gauze rings were alternately filled in the column. The other was the homogeneous bed, where Kogel catalysts and Dixon gauze rings were homogeneously mixed and filled in the column. We found that (1) the homogeneously packed bed was more efficient than the layered packed bed, and (2) the catalyst quantity was optimal, which resulted in the highest separative performance. In this study, the effect of the gas-liquid ratio (G/L) on the optimum catalyst quantity was studied experimentally in a homogeneously packed bed. When the value of G/L was 1.7, total separation factors were relatively small and the optimum catalyst quantity could not be determined. On the other hand, when the values of G/L were 0.9 and 0.7, the values of the total separation factors had maximums and the optimal quantities of the catalyst were clearly obtained

Bulk and contact resistances of gas diffusion layers in proton exchange membrane fuel cells

Science.gov (United States)

Ye, Donghao; Gauthier, Eric; Benziger, Jay B.; Pan, Mu

2014-06-01

A multi-electrode probe is employed to distinguish the bulk and contact resistances of the catalyst layer (CL) and the gas diffusion layer (GDL) with the bipolar plate (BPP). Resistances are compared for Vulcan carbon catalyst layers (CL), carbon paper and carbon cloth GDL materials, and GDLs with microporous layers (MPL). The Vulcan carbon catalyst layer bulk resistance is 100 times greater than the bulk resistance of carbon paper GDL (Toray TG-H-120). Carbon cloth (CCWP) has bulk and contact resistances twice those of carbon paper. Compression of the GDL decreases the GDL contact resistance, but has little effect on the bulk resistance. Treatment of the GDL with polytetrafluoroethylene (PTFE) increases the contact resistance, but has little effect on the bulk resistance. A microporous layer (MPL) added to the GDL decreases the contact resistance, but has little effect on the bulk resistance. An equivalent circuit model shows that for channels less than 1 mm wide the contact resistance is the major source of electronic resistance and is about 10% of the total ohmic resistance associated with the membrane electrode assembly.

Enhanced regeneration of degraded polymer solar cells by thermal annealing

Energy Technology Data Exchange (ETDEWEB)

Kumar, Pankaj, E-mail: pankaj@mail.nplindia.ernet.in [CSIR-National Physical Laboratory, Dr. K. S. Krishnan Marg, New Delhi 110012 (India); Centre for Organic Electronics, Physics, University of Newcastle, Callaghan NSW-2308 (Australia); Bilen, Chhinder; Zhou, Xiaojing; Belcher, Warwick J.; Dastoor, Paul C., E-mail: Paul.Dastoor@newcastle.edu.au [Centre for Organic Electronics, Physics, University of Newcastle, Callaghan NSW-2308 (Australia); Feron, Krishna [Centre for Organic Electronics, Physics, University of Newcastle, Callaghan NSW-2308 (Australia); CSIRO Energy Technology, P. O. Box 330, Newcastle NSW 2300 (Australia)

2014-05-12

The degradation and thermal regeneration of poly(3-hexylethiophene) (P3HT):[6,6]-phenyl-C{sub 61}-butyric acid methyl ester (PCBM) and P3HT:indene-C{sub 60} bisadduct (ICBA) polymer solar cells, with Ca/Al and Ca/Ag cathodes and indium tin oxide/poly(ethylene-dioxythiophene):polystyrene sulfonate anode have been investigated. Degradation occurs via a combination of three primary pathways: (1) cathodic oxidation, (2) active layer phase segregation, and (3) anodic diffusion. Fully degraded devices were subjected to thermal annealing under inert atmosphere. Degraded solar cells possessing Ca/Ag electrodes were observed to regenerate their performance, whereas solar cells having Ca/Al electrodes exhibited no significant regeneration of device characteristics after thermal annealing. Moreover, the solar cells with a P3HT:ICBA active layer exhibited enhanced regeneration compared to P3HT:PCBM active layer devices as a result of reduced changes to the active layer morphology. Devices combining a Ca/Ag cathode and P3HT:ICBA active layer demonstrated ∼50% performance restoration over several degradation/regeneration cycles.

Enhanced regeneration of degraded polymer solar cells by thermal annealing

International Nuclear Information System (INIS)

Kumar, Pankaj; Bilen, Chhinder; Zhou, Xiaojing; Belcher, Warwick J.; Dastoor, Paul C.; Feron, Krishna

2014-01-01

The degradation and thermal regeneration of poly(3-hexylethiophene) (P3HT):[6,6]-phenyl-C 61 -butyric acid methyl ester (PCBM) and P3HT:indene-C 60 bisadduct (ICBA) polymer solar cells, with Ca/Al and Ca/Ag cathodes and indium tin oxide/poly(ethylene-dioxythiophene):polystyrene sulfonate anode have been investigated. Degradation occurs via a combination of three primary pathways: (1) cathodic oxidation, (2) active layer phase segregation, and (3) anodic diffusion. Fully degraded devices were subjected to thermal annealing under inert atmosphere. Degraded solar cells possessing Ca/Ag electrodes were observed to regenerate their performance, whereas solar cells having Ca/Al electrodes exhibited no significant regeneration of device characteristics after thermal annealing. Moreover, the solar cells with a P3HT:ICBA active layer exhibited enhanced regeneration compared to P3HT:PCBM active layer devices as a result of reduced changes to the active layer morphology. Devices combining a Ca/Ag cathode and P3HT:ICBA active layer demonstrated ∼50% performance restoration over several degradation/regeneration cycles

[Water utilization characteristics of the degraded poplar shelterbelts in Zhangbei, Hebei, China.

Science.gov (United States)

Zhang, Huan; Cao, Jun; Wang, Hua Bing; Song, Bo; Jia, Guo Dong; Liu, Zi Qiang; Yu, Xin Xiao; Zeng, Jia

2018-05-01

In Zhangbei County, Hebei Province, poplar-dominated shelterbelts are degraded to different extents. Water availability is the main limiting factor for plant survival in arid areas. The purpose of this study was to reveal the relationship between water availability and poplar degradation. Based on the hydrogen and oxygen stable isotope techniques, we explored the water sources of Populus simonii under different degradation degrees by comparing the isotopic values of P. simonii xylem water with that in potential water source, and calculated the utilization ratio of each water source. The results showed that the water sources of poplar trees varied with degradation degree. The water sources of P. simonii gradually transferred from the deep layer to the surface layer with the increases of degradation. P. simonii with no degradation mainly absorbed soil water in the range of 320-400 cm, with the utilization rate being 25.1%. P. simonii with slight degradation mainly used soil water at depth of 120-180, 180-240 and 240-320 cm. The total utilization rate of three layers was close to 50.0%, with less utilization of water from other layers. The moderately degraded P. simonii mainly used soil water at depth of 20-40, 40-60 and 60-80 cm. The utilization rate of each layer was 17.5%-20.9%, and the contribution rate of soil water under 120 cm was less than 10.0%. The severely degraded P. simonii mainly used water from surface soil layer (0-20 cm), with the utilization rate being 30.4%, which was significantly higher than that of other water sources. The water sources of poplar shelter forests were gradually shallower during the process of degradation. However, the low soil water content in the shallow layer could not meet the normal water demand of poplar, which would accelerate the degradation and even decline of poplar.

BiVO4 /N-rGO nano composites as highly efficient visible active photocatalyst for the degradation of dyes and antibiotics in eco system.

Science.gov (United States)

Appavu, Brindha; Thiripuranthagan, Sivakumar; Ranganathan, Sudhakar; Erusappan, Elangovan; Kannan, Kathiravan

2018-04-30

Herein, we report the synthesis of novel nitrogen doped reduced graphene oxide/ BiVO 4 photo catalyst by single step hydrothermal method. The physicochemical properties of the catalysts were characterized using XRD, N 2 adsorption-desorption, Raman, XPS, SEM TEM, DRS-UV and EIS techniques. The synthesized catalysts were tested for their catalytic activity in the photo degradation of some harmful textile dyes (methylene blue & congo red) and antibiotics (metronidazole and chloramphenicol) under visible light irradiation. Reduced charge recombination and enhanced photocatalytic activity were observed due to the concerted effect between BiVO 4 and nitrogen-rGO. The degradation efficiency of BiVO 4 /N-rGO in the degradation of CR and MB was remarkably high i.e 95% and 98% under visible light irradiation. Similarly 95% of MTZ and 93% of CAP were degraded under visible light irradiation. HPLC studies implied that both the dyes and antibiotics were degraded to the maximum extent. The plausible photocatalytic mechanism on the basis of experimental results was suggested. Copyright © 2018 Elsevier Inc. All rights reserved.

Synthesis of multi-layer graphene and multi-wall carbon nanotubes from direct decomposition of ethanol by microwave plasma without using metal catalysts

International Nuclear Information System (INIS)

Rincón, R; Melero, C; Jiménez, M; Calzada, M D

2015-01-01

The synthesis of nanostructured carbon materials by using microwave plasmas at atmospheric pressure is presented. This technique involves only one step and without any other supplementary chemical process or metal catalyst. Multi-layer graphene, multi-wall carbon nananotubes and H 2 were obtained by the plasma after ethanol decomposition. Strong emissions of both C 2 molecular bands and C carbon were emitted by the plasma during the process. Futhermore, plasma parameters were studied. Our research shows that both C 2 radicals and high gas temperatures (>3000 K) are required for the synthesis of these materials, which contribute to the understanding of materials synthesis by plasma processes. (fast track communication)

Decolorization of Methylene Blue with TiO2 Sol via UV Irradiation Photocatalytic Degradation

Directory of Open Access Journals (Sweden)

Jun Yao

2010-01-01

Full Text Available TiO2 sol was prepared for the degradation of methylene blue (MB solution under ultraviolet (UV irradiation. The absorption spectra of MB indicated that the maximum wavelength, 663 nm, almost kept the same. The performance of 92.3% for color removal was reached after 160 min. The particle size of TiO2 sol was about 22.5 nm. X-ray diffraction showed that TiO2 consisted of a single anatase phase. The small size and anatase phase probably resulted in high photocatalytic activity of TiO2 sol. The degradation ratio decreased as the initial concentration of MB increased. The photodegradation efficiency decreased in the order of pH 2>pH 9>pH 7. Regarding catalyst load, the degradation increased with the mass of catalyst up to an amount of 1.5 g⋅L−1 then decreased as the mass continued to increase. The addition of H2O2 to TiO2 sol resulted in an increase on the degradation ratio.

Solar photocatalytic degradation of isoproturon over TiO{sub 2}/H-MOR composite systems

Energy Technology Data Exchange (ETDEWEB)

Sharma, Mangalampalli V. Phanikrishna; Durgakumari, Valluri [Inorganic and Physical Chemistry Division, Indian Institute of Chemical Technology, Hyderabad 500607 (India); Subrahmanyam, Machiraju [Inorganic and Physical Chemistry Division, Indian Institute of Chemical Technology, Hyderabad 500607 (India)], E-mail: subrahmanyam@iict.res.in

2008-12-30

The photocatalytic degradation and mineralization of isoproturon herbicide was investigated in aqueous solution containing TiO{sub 2} over H-mordenite (H-MOR) photocatalysts under solar light. The catalysts are characterized by X-ray diffraction (XRD), UV-Vis diffused reflectance spectra (UV-Vis DRS), Fourier transform-infra red spectra (FT-IR) and scanning electron microscopy (SEM) techniques. The effect of TiO{sub 2}, H-MOR support and different wt% of TiO{sub 2} over the support on the photocatalytic degradation and influence of parameters such as TiO{sub 2} loading, catalyst amount, pH and initial concentration of isoproturon on degradation are evaluated. 15 wt% TiO{sub 2}/H-MOR composite is found to be optimum. The degradation reaction follows pseudo-first order kinetics and is discussed in terms of Langmuir-Hinshelwood (L-H) kinetic model. The extent of isoproturon mineralization studied with chemical oxygen demand (COD) and total organic carbon (TOC) measurements and {approx}80% mineralization occurred in 5 h. A plausible mechanism is proposed based on the intermediates identified by liquid chromatography-mass spectroscopy (LC-MS)

Nickel nanoparticles-chitosan composite coated cellulose filter paper: An efficient and easily recoverable dip-catalyst for pollutants degradation.

Science.gov (United States)

Kamal, Tahseen; Khan, Sher Bahadar; Asiri, Abdullah M

2016-11-01

In this report, we used cellulose filter paper (FP) as high surface area catalyst supporting green substrate for the synthesis of nickel (Ni) nanoparticles in thin chitosan (CS) coating layer and their easy separation was demonstrated for next use. In this work, FP was coated with a 1 wt% CS solution onto cellulose FP to prepare CS-FP as an economical and environment friendly host material. CS-FP was put into 0.2 M NiCl 2 aqueous solution for the adsorption of Ni 2+ ions by CS coating layer. The Ni 2+ adsorbed CS-FP was treated with 0.1 M NaBH 4 aqueous solution to convert the ions into nanoparticles. Thus, we achieved Ni nanoparticles-CS composite through water based in-situ preparation process. Successful Ni nanoparticles formations was assessed by FESEM and EDX analyses. FTIR used to track the interactions between nanoparticles and host material. Furthermore, we demonstrated that the nanocomposite displays an excellent catalytic activity and reusability in three reduction reactions of toxic compounds i.e. conversion of 4-nitrophenol to 4-aminophenol, 2-nitrophenol to 2-aminophenol, and methyl orange dye reduction by NaBH 4 . Such a fabrication process of Ni/CS-FP may be applicable for the immobilization of other metal nanoparticles onto FP for various applications in catalysis, sensing, and environmental sciences. Copyright © 2016 Elsevier Ltd. All rights reserved.

The fusion of dt{mu}, tt{mu} and dd{mu} molecules in three-layer arrangement including deuterium degrader and moderator

Energy Technology Data Exchange (ETDEWEB)

Gheisari, R. [Physics Department, Persian Gulf University, Bushehr 75169 (Iran)

2010-09-15

Muon dynamics and forced chemical confinement fusion in three-layer arrangement consisting of the H/T, D{sub 2} (the degrader and moderator) and D/T fusion layers are investigated with a new kinetic model. Point kinematic equations are numerically solved to calculate the numbers of dt{mu}, tt{mu} and dd{mu} chain reactions. We show that the {mu}-cycling coefficient X{sub c} approximately equals 156, at optimal condition. Our model and results are in contradiction with beliefs of Mahdavi and Zanganeh. Our model is confirmed by recent experiment where was performed for the hydrogen mixture. (author)

Photocatalytic enhancement of floating photocatalyst: Layer-by-layer hybrid carbonized chitosan and Fe-N- codoped TiO{sub 2} on fly ash cenospheres

Energy Technology Data Exchange (ETDEWEB)

Song, Jingke; Wang, Xuejiang, E-mail: wangxj@tongji.edu.cn; Bu, Yunjie; Wang, Xin; Zhang, Jing; Huang, Jiayu; Ma, RongRong; Zhao, Jianfu

2017-01-01

Highlights: • Multifunctional TiO{sub 2} was coated on floating fly ash cenospheres. • TiO{sub 2} was integrated with carbonaceous layer from chitosan and Fe-N co-doping. • Carbonized chitosan improved the adsorption of pollutant and photon absorption ability of TiO{sub 2}. • Modified TiO{sub 2} exhibited superior photocatalytic activity and better recyclability. - Abstract: Due to the advantage of floating on water surface, floating photocatalysts show higher rates of radical formation and collection efficiencies. And they were expected to be used for solar remediation of non-stirred and non-oxygenated reservoirs. In this research, floating fly ash cenospheres (FAC) supported layer-by- layer hybrid carbonized chitosan and Fe-N-codoped TiO{sub 2} was prepared by a simple sol-gel method. The catalysts were characterized by X-ray diffraction(XRD), field emission scanning electron microscopy(FESEM), fourier transform infrared spectroscopy(FTIR), X-ray photoelectron spectroscopy (XPS), UV–vis diffuse reflectance spectroscopy(DRS), nitrogen adsorption analyses for Brunauer-Emmett-Teller (BET) specific surface area. It is indicated that Fe-N codoped narrowed the material’s band gap, and the layer of carbonized chitosan (Cts) increased the catalyst’s adsorption capacity and the absorption ability of visible light. Comparing with Fe-N-TiO{sub 2}/FAC and N-TiO{sub 2}/FAC, the composite photocatalyst show excellent performance on the degradation of RhB. Photodegradation rate of RhB by Fe-N-TiO{sub 2}/FAC-Cts was 0.01018 min{sup −1}, which is about 1.5 and 2.09 times higher than Fe-N-TiO{sub 2}/FAC and N-TiO{sub 2}/FAC under visible light irradiation in 240 min, respectively. The dye photosentization, capture of holes and electrons by Fe{sup 3+} ion, and synergistic effect of adsorption and photodegradation were attributed to the results for the improvement of photocatalytic performance. The floating photocatalyst can be reused for at least three consecutive

Synthesis of novel perfluoroalkylglucosides on zeolite and non-zeolite catalysts.

Science.gov (United States)

Nowicki, Janusz; Mokrzycki, Łukasz; Sulikowski, Bogdan

2015-04-08

Perfluoroalkylglucosides comprise a very important class of fluorine-containing surfactants. These compounds can be synthesized by using the Fisher reaction, starting directly from glucose and the required perfluoroalcohols. We wish to report on the use of zeolite catalysts of different structure and composition for the synthesis of perfluoroalkylglucosides when using glucose and 1-octafluoropentanol as substrates. Zeolites of different pore architecture have been chosen (ZSM-5, ZSM-12, MCM-22 and Beta). Zeolites were characterized by XRD, nitrogen sorption, scanning electron microscopy (SEM) and solid-state 27Al MAS NMR spectroscopy. The activity of the zeolite catalysts in the glycosidation reaction was studied in a batch reactor at 100 °C below atmospheric pressure. The performance of zeolites was compared to other catalysts, an ion-exchange resin (Purolite) and a montmorillonite-type layered aluminosilicate. The catalytic performance of zeolite Beta was the highest among the zeolites studied and the results were comparable to those obtained over Purolite and montmorillonite type catalysts.

Development of low light-off catalyst; Teion kassei ni sugureta shokubai no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takemoto, T; Ichikawa, S; Koda, Y; Yamamoto, E; Sumida, H; Yamada, H; Shigetsu, M; Komatsu, K [Mazda Motor Corp., Tokyo (Japan)

1997-10-01

A new type of three way catalyst was developed in order to reduce HC, CO and NOx in cold exhaust gas. This catalyst consists of double layer, and has a base support material of alumina and oxygen storage components (OSC) loaded with active metals including platinum. palladium and rhodium. It has good light-off performance and high catalytic activity. This catalyst includes two types of OSC. One is CeO2, and the other is CePrO2 that makes possible to improve NOx conversion at high exhaust gas temperature. 8 refs., 13 figs., 2 tabs.

Co-Assembled Supported Catalysts: Synthesis of Nano-Structured Supported Catalysts with Hierarchic Pores through Combined Flow and Radiation Induced Co-Assembled Nano-Reactors

Directory of Open Access Journals (Sweden)

Galip Akay

2016-05-01

Full Text Available A novel generic method of silica supported catalyst system generation from a fluid state is presented. The technique is based on the combined flow and radiation (such as microwave, thermal or UV induced co-assembly of the support and catalyst precursors forming nano-reactors, followed by catalyst precursor decomposition. The transformation from the precursor to supported catalyst oxide state can be controlled from a few seconds to several minutes. The resulting nano-structured micro-porous silica supported catalyst system has a surface area approaching 300 m2/g and X-ray Diffraction (XRD-based catalyst size controlled in the range of 1–10 nm in which the catalyst structure appears as lamellar sheets sandwiched between the catalyst support. These catalyst characteristics are dependent primarily on the processing history as well as the catalyst (Fe, Co and Ni studied when the catalyst/support molar ratio is typically 0.1–2. In addition, Ca, Mn and Cu were used as co-catalysts with Fe and Co in the evaluation of the mechanism of catalyst generation. Based on extensive XRD, Scanning Electron Microscopy (SEM and Transmission Electron Microscopy (TEM studies, the micro- and nano-structure of the catalyst system were evaluated. It was found that the catalyst and silica support form extensive 0.6–2 nm thick lamellar sheets of 10–100 nm planar dimensions. In these lamellae, the alternate silica support and catalyst layer appear in the form of a bar-code structure. When these lamellae structures pack, they form the walls of a micro-porous catalyst system which typically has a density of 0.2 g/cm3. A tentative mechanism of catalyst nano-structure formation is provided based on the rheology and fluid mechanics of the catalyst/support precursor fluid as well as co-assembly nano-reactor formation during processing. In order to achieve these structures and characteristics, catalyst support must be in the form of silane coated silica nano

Recycling of waste spent catalyst in road construction and masonry blocks.

Science.gov (United States)

Taha, Ramzi; Al-Kamyani, Zahran; Al-Jabri, Khalifa; Baawain, Mahad; Al-Shamsi, Khalid

2012-08-30

Waste spent catalyst is generated in Oman as a result of the cracking process of petroleum oil in the Mina Al-Fahl and Sohar Refineries. The disposal of spent catalyst is of a major concern to oil refineries. Stabilized spent catalyst was evaluated for use in road construction as a whole replacement for crushed aggregates in the sub-base and base layers and as a partial replacement for Portland cement in masonry blocks manufacturing. Stabilization is necessary as the waste spent catalyst exists in a powder form and binders are needed to attain the necessary strength required to qualify its use in road construction. Raw spent catalyst was also blended with other virgin aggregates, as a sand or filler replacement, for use in road construction. Compaction, unconfined compressive strength and leaching tests were performed on the stabilized mixtures. For its use in masonry construction, blocks were tested for unconfined compressive strength at various curing periods. Results indicate that the spent catalyst has a promising potential for use in road construction and masonry blocks without causing any negative environmental impacts. Copyright © 2012 Elsevier B.V. All rights reserved.