WorldWideScience

Sample records for casting dies final

  1. National Metal Casting Research Institute final report. Volume 2, Die casting research

    Jensen, D. [University of Northern Iowa, Cedar Falls, IA (United States). Dept. of Industrial Technology] [comp.

    1994-06-01

    Four subprojects were completed: development and evaluation of die coatings, accelerated die life characterization of die materials, evaluation of fluid flow and solidification modeling programs, selection and characterization of Al-based die casting alloys, and influence of die materials and coatings on die casting quality.

  2. Die Casting Part Distortion: Prediction and Attenuation; FINAL

    Allen Miller, R.

    2002-01-01

    The goal of this research was to predict the part deformation and residual stresses after ejection from the die and cooling to room temperature. A finite element model was built to achieve this goal and several modeling techniques were investigated throughout this research. Die-casting is a very complex process and the researchers are faced with a large number of hard to solve physical problems when modeling the process. Several assumptions are made in our simulation model. The first significant assumption is the instantaneous cavity filling. This means that the cavity filling stage is not considered in our model. Considering the cavity filling stage increases the modeling complexity as a result of different flow patterns. expected in the shot sleeve, gate, runner and different cavity features. The flow of gas from the cavity through the vents is another problem that is ignored in our model as a result of this assumption. Our second assumption is that the cast metal has uniform temperature distribution inside the cavity, at the starting point of simulation. This temperature is assumed to be over liquidus limit, i.e. the solid fraction is 0.0% of the cast metal. The third assumption is due to ABAQUS (commercial software used in this research) limitations. ABAQUS cannot deal with multi-phase models; therefore we use solid elements to define the casting instead of multi-phase (liquid/solid) elements. Liquid elements can carry the hydrostatic pressure from the shot sleeve and apply it on the cavity surfaces, while the solid elements do not have this capability. To compensate for this assumption we add the cavity pressure as a boundary condition and apply it on the cavity surface separately from the part. Another issue with this assumption is that, liquid casting can follow the cavity shape when it distorts. With the use of solid elements to represent the casting during its liquid state, it loses this capability to follow the cavity. Several techniques were tested to

  3. Dimensional control of die castings

    Karve, Aniruddha Ajit

    The demand for net shape die castings, which require little or no machining, is steadily increasing. Stringent customer requirements are forcing die casters to deliver high quality castings in increasingly short lead times. Dimensional conformance to customer specifications is an inherent part of die casting quality. The dimensional attributes of a die casting are essentially dependent upon many factors--the quality of the die and the degree of control over the process variables being the two major sources of dimensional error in die castings. This study focused on investigating the nature and the causes of dimensional error in die castings. The two major components of dimensional error i.e., dimensional variability and die allowance were studied. The major effort of this study was to qualitatively and quantitatively study the effects of casting geometry and process variables on die casting dimensional variability and die allowance. This was accomplished by detailed dimensional data collection at production die casting sites. Robust feature characterization schemes were developed to describe complex casting geometry in quantitative terms. Empirical modeling was utilized to quantify the effects of the casting variables on dimensional variability and die allowance for die casting features. A number of casting geometry and process variables were found to affect dimensional variability in die castings. The dimensional variability was evaluated by comparisons with current published dimensional tolerance standards. The casting geometry was found to play a significant role in influencing the die allowance of the features measured. The predictive models developed for dimensional variability and die allowance were evaluated to test their effectiveness. Finally, the relative impact of all the components of dimensional error in die castings was put into perspective, and general guidelines for effective dimensional control in the die casting plant were laid out. The results of

  4. Simple visualization techniques for die casting part and die design. Final report, July 1, 1995--September 30, 1997

    Miller, R.A.; Lu, S.C.; Rebello, A.B.

    1998-05-01

    The objective of this work was to develop and test die casting design evaluation techniques based on the visualization of geometric data that is related to potential defects of problems. Specifically, thickness information is used to provide insight into potential thermal problems in the part and die. Distance from the gate and a special type of animation of the fill pattern is used to provide an assessment of gate, vent and overflow locations. Techniques have been developed to convert part design information in the form of STL files to a volume-based representation called a voxel model. The use of STL files makes the process CAD system independent. Once in voxel form, methods that were developed in this work are used to identify thick regions in the part, thin regions in the part and/or die, distance from user specified entry locations (gates), and the qualitative depiction of the fill pattern. The methods were tested with a prototype implementation on the UNIX platform. The results of comparisons with numerical simulation and field reported defects were surprisingly good. The fill-related methods were also compared against short-shots and a water analog study using high speed video. The report contains the results of the testing plus detailed background material on the construction of voxel models, the methods used for displaying results, and the computational geometric reasoning methods used to create die casting-related information from the voxel model for display to the user.

  5. Simple visualization techniques for die casting part and die design. Final report, July 1, 1995--September 30, 1997

    Miller, R.A.; Lu, S.C.; Rebello, A.B.

    1998-05-01

    The objective of this work was to develop and test die casting design evaluation techniques based on the visualization of geometric data that is related to potential defects of problems. Specifically, thickness information is used to provide insight into potential thermal problems in the part and die. Distance from the gate and a special type of animation of the fill pattern is used to provide an assessment of gate, vent and overflow locations. Techniques have been developed to convert part design information in the form of STL files to a volume-based representation called a voxel model. The use of STL files makes the process CAD system independent. Once in voxel form, methods that were developed in this work are used to identify thick regions in the part, thin regions in the part and/or die, distance from user specified entry locations (gates), and the qualitative depiction of the fill pattern. The methods were tested with a prototype implementation on the UNIX platform. The results of comparisons with numerical simulation and field reported defects were surprisingly good. The fill-related methods were also compared against short-shots and a water analog study using high speed video. The report contains the results of the testing plus detailed background material on the construction of voxel models, the methods used for displaying results, and the computational geometric reasoning methods used to create die casting-related information form the voxel model for display to the user.

  6. Clean Metal Casting; FINAL

    Makhlouf M. Makhlouf; Diran Apelian

    2002-01-01

    The objective of this project is to develop a technology for clean metal processing that is capable of consistently providing a metal cleanliness level that is fit for a given application. The program has five tasks: Development of melt cleanliness assessment technology, development of melt contamination avoidance technology, development of high temperature phase separation technology, establishment of a correlation between the level of melt cleanliness and as cast mechanical properties, and transfer of technology to the industrial sector. Within the context of the first task, WPI has developed a standardized Reduced Pressure Test that has been endorsed by AFS as a recommended practice. In addition, within the context of task1, WPI has developed a melt cleanliness sensor based on the principles of electromagnetic separation. An industrial partner is commercializing the sensor. Within the context of the second task, WPI has developed environmentally friendly fluxes that do not contain fluorine. Within the context of the third task, WPI modeled the process of rotary degassing and verified the model predictions with experimental data. This model may be used to optimize the performance of industrial rotary degassers. Within the context of the fourth task, WPI has correlated the level of melt cleanliness at various foundries, including a sand casting foundry, a permanent mold casting foundry, and a die casting foundry, to the casting process and the resultant mechanical properties. This is useful in tailoring the melt cleansing operations at foundries to the particular casting process and the desired properties of cast components

  7. Microstructures and properties of aluminum die casting alloys

    M. M. Makhlouf; D. Apelian; L. Wang

    1998-10-01

    This document provides descriptions of the microstructure of different aluminum die casting alloys and to relate the various microstructures to the alloy chemistry. It relates the microstructures of the alloys to their main engineering properties such as ultimate tensile strength, yield strength, elongation, fatigue life, impact resistance, wear resistance, hardness, thermal conductivity and electrical conductivity. Finally, it serves as a reference source for aluminum die casting alloys.

  8. Modeling the Mechanical Performance of Die Casting Dies

    R. Allen Miller

    2004-02-27

    The following report covers work performed at Ohio State on modeling the mechanical performance of dies. The focus of the project was development and particularly verification of finite element techniques used to model and predict displacements and stresses in die casting dies. The work entails a major case study performed with and industrial partner on a production die and laboratory experiments performed at Ohio State.

  9. Economical surface treatment of die casting dies to prevent soldering in high pressure casting

    Fraser, D.T.; Jahedi, M.Z.

    2001-01-01

    This paper describes the use of a gas oxidation treatment of H13 tool steel to develop a compact iron oxide layer at the surface of core pins to prevent soldering in high pressure die casting. The performance of oxide layers in the protection of die steel against soldering during high pressure die casting was tested in a specially designed die using removable core pins and Al-11 Si-3 Cu casting alloy. The gas oxidation treatment can be applied at low temperatures and to large areas of the die surface. In addition this process is very cost effective compared to other coating processes such as physical vapour deposition (PVD), or thermo-reactive diffusion (TRD) coatings. This work demonstrated that surface treatment producing pure magnetite (Fe 3 O 4 ) layers are more protective than oxide layers containing a combination of Fe 3 O 4 (magnetite) and Fe 3 O 3 (haematite). The magnetite layer acts as a barrier between the die steel/casting alloy interface and prevents the formation of inter-metallic phases. Optical microscopy and scanning electron microscope were used to determine the thickness of the oxide layer, while X-ray diffraction was performed to determine the oxide phase structure

  10. Thermal Fatigue of Die-Casting Dies: An Overview

    Abdulhadi Hassan A.

    2016-01-01

    Full Text Available Coupled studies by experimental and numerical simulations are necessary for an increased understanding of the material behaviour as related to the interaction between the thermal and mechanical conditions. This paper focus on the mechanisms of thermal fatigue in the failure of dies and cores used in the die casting of aluminum alloys. The thermal fatigue resistance is expressed by two crack parameters which are the average maximum crack and the average cracked area. Samples of various types of H13 steel were compared with a standard H13 steel by testing under identical thermal fatigue cycles. To determine the thermal constraint developed in the sample during the test, a finite difference technique was used to obtain the temperature distribution, based on temperature measurements at the boundaries. The resulting stresses and strains were computed, and the strain calculated at the edge or weakest point of the sample was used to correlate the number of cycles to crack initiation. As the strain at the edge increased, the number of cycles to failure decreased. The influence of various factors on thermal fatigue behavior was studied including austenitizing temperature, surface condition, stress relieving, casting, vacuum melting, and resulfurization. The thermal fatigue resistance improved as the austenitizing temperature increased from 1750 to 2050ºF.

  11. Modelling the Cast Component Weight in Hot Chamber Die Casting using Combined Taguchi and Buckingham's π Approach

    Singh, Rupinder

    2018-02-01

    Hot chamber (HC) die casting process is one of the most widely used commercial processes for the casting of low temperature metals and alloys. This process gives near-net shape product with high dimensional accuracy. However in actual field environment the best settings of input parameters is often conflicting as the shape and size of the casting changes and one have to trade off among various output parameters like hardness, dimensional accuracy, casting defects, microstructure etc. So for online inspection of the cast components properties (without affecting the production line) the weight measurement has been established as one of the cost effective method (as the difference in weight of sound and unsound casting reflects the possible casting defects) in field environment. In the present work at first stage the effect of three input process parameters (namely: pressure at 2nd phase in HC die casting; metal pouring temperature and die opening time) has been studied for optimizing the cast component weight `W' as output parameter in form of macro model based upon Taguchi L9 OA. After this Buckingham's π approach has been applied on Taguchi based macro model for the development of micro model. This study highlights the Taguchi-Buckingham based combined approach as a case study (for conversion of macro model into micro model) by identification of optimum levels of input parameters (based on Taguchi approach) and development of mathematical model (based on Buckingham's π approach). Finally developed mathematical model can be used for predicting W in HC die casting process with more flexibility. The results of study highlights second degree polynomial equation for predicting cast component weight in HC die casting and suggest that pressure at 2nd stage is one of the most contributing factors for controlling the casting defect/weight of casting.

  12. Evaluation of porosity in Al alloy die castings

    M. Říhová

    2012-01-01

    Full Text Available Mechanical properties of an Al-alloy die casting depend significantly on its structural properties. Porosity in Al-alloy castings is one of the most frequent causes of waste castings. Gas pores are responsible for impaired mechanical-technological properties of cast materials. On the basis of a complex evaluation of experiments conducted on AlSi9Cu3 alloy samples taken from the upper engine block which was die- cast with and without local squeeze casting it can be said that castings manufactured without squeeze casting exhibit maximum porosity in the longitudinal section. The area without local squeeze casting exhibits a certain reduction in mechanical properties and porosity increased to as much as 5%. However, this still meets the norms set by SKODA AUTO a.s.

  13. Modeling of high temperature- and diffusion-controlled die soldering in aluminum high pressure die casting

    Domkin, Konstantin; Hattel, Jesper Henri; Thorborg, Jesper

    2009-01-01

    of the die lifetime based on a quantitative analysis of die soldering in the framework of the numerical simulations of the die-casting process. Full 3D simulations of the process, including the filling. solidification, and the die cooling, are carried out using the casting simulation software MAGMAsoft....... The resulting transient temperature fields on the die surface and in the casting are then post-processed to estimate the die soldering. The present work deals only with the metallurgical/chemical kind of soldering which occurs at high temperatures and involves formation and growth of intermetallic layers...

  14. Aluminium Foam and Magnesium Compound Casting Produced by High-Pressure Die Casting

    Iban Vicario

    2016-01-01

    Full Text Available Nowadays, fuel consumption and carbon dioxide emissions are two of the main focal points in vehicle design, promoting the reduction in the weight of vehicles by using lighter materials. The aim of the work is to evaluate the influence of different aluminium foams and injection parameters in order to obtain compound castings with a compromise between the obtained properties and weight by high-pressure die cast (HPDC using aluminium foams as cores into a magnesium cast part. To evaluate the influence of the different aluminium foams and injection parameters on the final casting products quality, the type and density of the aluminium foam, metal temperature, plunger speed, and multiplication pressure have been varied within a range of suitable values. The obtained compound HPDC castings have been studied by performing visual and RX inspections, obtaining sound composite castings with aluminium foam cores. The presence of an external continuous layer on the foam surface and the correct placement of the foam to support injection conditions permit obtaining good quality parts. A HPDC processed magnesium-aluminium foam composite has been developed for a bicycle application obtaining a suitable combination of mechanical properties and, especially, a reduced weight in the demonstration part.

  15. New trends in cold-chamber die casting machine design

    R. Dańko

    2015-07-01

    Full Text Available Larger and larger proportions of aluminium castings, especially those produced by the die casting process, can be observed during recent years in the automotive industry, house-hold articles and others. In case of the automotive industry, apart from the traditional elements produced by the die pressure method such as engine blocks or crank shaft bedplates, aluminium is displacing steel from structural parts of cars (‘body in white’. The current state and development directions of the structural solutions of cold-chamber die castings are analysed in this paper. These solutions drive the prospective development of these machines and die casting technology. The focus is mainly on essential functional systems such as: hydraulic drives of closing and locking units, as well as pressing in die machines of known companies present on the European market.

  16. Die design and process optimization of die cast V6 engine blocks

    Henry Hu

    2005-02-01

    Full Text Available The use of aluminum, particularly for engine blocks, has grown considerably in the past ten years, and continues to rise in the automotive industry. In order to enhance the quality and engineering functionality of die cast engine blocks, die design and processes have to be optimized. In this study, a computer simulation software, MAGMAsoft, as an advanced tool for optimizing die design and casting process, was emplooyed to virtually visualize cavity filling and patterns of a V6 engine block. The original die design and process was simulated first to establish a baseline. A reality check was used to verify the predicted results. Then, the die modification with a different unner system was made by using a CAD software, Unigraphics (UG. The simulation on combinations of the modified die design and revised process was performed to examine the effect of die modification and process change on flow filling of V6 engine blocks. The simulated prediction indicateds that the enhancement of cavity filling due to the die and process modification minimizeds the occurrence of defects during casting, and consequently improves the quality of blocks. The results of mechanical testing show a significant increase in fatigue strengths, and a moderately improvement on tensile properties for the blocks die cast with the new die design and prpocess in comparison with those produced by the original ones.

  17. Strength and deformation behaviour of magnesium die casting alloys

    Regener, D.; Schick, E.; Wagner, I.; Heyse, H.

    1999-01-01

    Modern magnesium die casting alloys are used for the manufacturing of automotive parts due to their low density, fortunate mechanical and physical properties as well as good castability and machinability. However, in comparison to other materials the automotive application of these alloys is still low. The reasons for this are among other things the shortage of relevant materials values, insufficient knowledge concerning the correlation between the microstructure and the mechanical properties as well as deficits in relation to the die cast technology. This paper investigates the influence of the microstructure and manufacture-induced defects like micro-shrinkage and gas pores on the strength and deformability of the alloys AZ91, AM50 and AE42 under tensile and bend loading. To characterise the microstructure in the dependence on the wall thickness, the investigations are mainly carried out using in situ specimens obtained from die castings. (orig.)

  18. Strength Estimation of Die Cast Beams Considering Equivalent Porous Defects

    Park, Moon Shik [Hannam Univ., Daejeon (Korea, Republic of)

    2017-05-15

    As a shop practice, a strength estimation method for die cast parts is suggested, in which various defects such as pores can be allowed. The equivalent porosity is evaluated by combining the stiffness data from a simple elastic test at the part level during the shop practice and the theoretical stiffness data, which are defect free. A porosity equation is derived from Eshelby's inclusion theory. Then, using the Mori-Tanaka method, the porosity value is used to draw a stress-strain curve for the porous material. In this paper, the Hollomon equation is used to capture the strain hardening effect. This stress-strain curve can be used to estimate the strength of a die cast part with porous defects. An elastoplastic theoretical solution is derived for the three-point bending of a die cast beam by using the plastic hinge method as a reference solution for a part with porous defects.

  19. Die Casting Mold Design for Aluminum Alloy Shell of Instrument

    Li Yuanyuan

    2015-01-01

    Full Text Available This paper is about die casting mold design for aluminum alloy shell of instrument. Three-dimensional model of the casting and mold are designed by using Pro/Engineer and AutoCad which can analyze forming quality. Digital design and theoretical calculation can greatly shorten product development cycle and mold design cycle, improve the accuracy of product design and mold design, and reduce the cost of mold design.

  20. Fan Fuel Casting Final Report

    Imhoff, Seth D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-09-28

    LANL was approached to provide material and design guidance for a fan-shaped fuel element. A total of at least three castings were planned. The first casting is a simple billet mold to be made from high carbon DU-10Mo charge material. The second and third castings are for optimization of the actual fuel plate mold. The experimental scope for optimization is only broad enough for a second iteration of the mold design. It is important to note that partway through FY17, this project was cancelled by the sponsor. This report is being written in order to capture the knowledge gained should this project resume at a later date.

  1. Reducing non value adding aluminium alloy in production of parts through high pressure die casting

    Pereira, MFVT

    2010-10-01

    Full Text Available in the cast part feed system, including overflows. CSIR intends using the results of this research for further development and application of high temperature die construction materials in high pressure die casting processes of light metal alloys...

  2. Automatic inspection of surface defects in die castings after machining

    S. J. Świłło

    2011-07-01

    Full Text Available A new camera based machine vision system for the automatic inspection of surface defects in aluminum die casting was developed by the authors. The problem of surface defects in aluminum die casting is widespread throughout the foundry industry and their detection is of paramount importance in maintaining product quality. The casting surfaces are the most highly loaded regions of materials and components. Mechanical and thermal loads as well as corrosion or irradiation attacks are directed primarily at the surface of the castings. Depending on part design and processing techniques, castings may develop surface discontinuities such as cracks or tears, inclusions due to chemical reactions or foreign material in the molten metal, and pores that greatly influence the material ability to withstand these loads. Surface defects may act as a stress concentrator initiating a fracture point. If a pressure is applied in this area, the casting can fracture. The human visual system is well adapted to perform in areas of variety and change; the visual inspection processes, on the other hand, require observing the same type of image repeatedly to detect anomalies. Slow, expensive, erratic inspection usually is the result. Computer based visual inspection provides a viable alternative to human inspectors. Developed by authors machine vision system uses an image processing algorithm based on modified Laplacian of Gaussian edge detection method to detect defects with different sizes and shapes. The defect inspection algorithm consists of three parameters. One is a parameter of defects sensitivity, the second parameter is a threshold level and the third parameter is to identify the detected defects size and shape. The machine vision system has been successfully tested for the different types of defects on the surface of castings.

  3. Numerical simulation of low pressure die-casting aluminum wheel

    Mi Guofa

    2009-02-01

    Full Text Available The FDM numerical simulation software, ViewCast system, was employed to simulate the low pressure die casting (LPDC of an aluminum wheel. By analyzing the mold-fi lling and solidifi cation stage of the LPDC process, the distribution of liquid fraction, temperature field and solidification pattern of castings were studied. The potential shrinkage defects were predicted to be formed at the rim/spoke junctions, which is in consistence with the X-ray detection result. The distribution pattern of the defects has also been studied. A solution towards reducing such defects has been presented. The cooling capacity of the mold was improved by installing water pipes both in the side mold and the top mold. Analysis on the shrinkage defects under forced cooling mode proved that adding the cooling system in the mold is an effective method for reduction of shrinkage defects.

  4. Energy and resource efficiency in aluminium die casting

    Heinemann, Tim

    2016-01-01

    This monograph provides a field-proven approach to analyze industrial production with a cross-company scope as well as regarding all hierarchical system levels of manufacturing enterprises. The book exemplifies this approach in the context of aluminum  die casting, and presents a set of measures which allow a 30 percent energy reduction along the value chain. The target audience primarily comprises researchers and experts in the field but the book may also be beneficial for graduate students.

  5. Casting defects and mechanical properties of high pressure die cast Mg-Zn-Al-RE alloys

    Xiao, Wenlong; Easton, Mark A.; Zhu, Suming; Nie, Jianfeng [CAST Cooperative Research Centre, Department of Materials Engineering Monash University, Melbourne, VIC (Australia); Dargusch, Matthew S. [School of Mechanical and Mining Engineering, University of Queensland, Brisbane, QLD (Australia); Gibson, Mark A. [CSIRO Process Science and Engineering, Melbourne, VIC (Australia); Jia, Shusheng [Key Laboratory of Automobile Materials, Ministry of Education, Department of Materials Science and Engineering Jilin University, Changchun (China)

    2012-02-15

    The die casting defects and tensile properties of high pressure die cast (HPDC) Mg-Zn-Al-RE alloys with various combinations of Zn and Al were studied. The results show that die casting defects in Mg-Zn-Al-RE alloys are affected by the percentage of Zn and Al contents. The hot tearing susceptibility (HTS) of Mg-Zn-Al-RE alloys tends to increase with increasing Zn content up to 6 wt%, while a further increase of Al and/or Zn content reduces the HTS. In tensile tests, the yield strength (YS) is generally improved by increasing Zn or Al content, whereas the tensile strength (TS) and ductility appear to depend largely on the presence of casting defects. Compared with Mg-Zn-Al alloys, the mechanical properties of the Mg-Zn-Al-RE alloy are significantly improved. The Mg-4Zn-4Al-4RE alloy is found to have few casting defects and the optimal tensile properties. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  6. Optimization of die filling in high pressure die cast part using MAGMAsoft®

    Kotas, Petr; Hattel, Jesper Henri

    2008-01-01

    Integrated modeling of an entire casting process has become a tool which favors design and optimization of manufactured parts. The aim of this project was to examine and optimize a high-pressure die cast part and its production process with respect to die filling and issues of residual stresses...... in the process and machine parameters were done and assessed. All simulations revealed that, the main causes of the problems were: a poor geometry of the casting leading to an improper filling pattern, and a massive gating system bringing thermal imbalance into the solidification process. Thus deformations due...... to residual stresses occurred. The numerical results were evaluated and appeared to be in agreement with the results from the actual manufacturing process. Based on these findings, proposals for improvements were given. In order to avoid distortions and cold shuts further geometrical adjustments should...

  7. Spray casting project final report

    Churnetski, S.R.; Thompson, J.E.

    1996-08-01

    Lockheed Martin Energy Systems, Inc. (Energy Systems), along with other participating organizations, has been exploring the feasibility of spray casting depleted uranium (DU) to near-net shape as a waste minimization effort. Although this technology would be useful in a variety of applications where DU was the material of choice, this effort was aimed primarily at gamma-shielding components for use in storage and transportation canisters for high-level radioactive waste, particularly in the Multipurpose Canister (MPC) application. In addition to the waste-minimization benefits, spray casting would simplify the manufacturing process by allowing the shielding components for MPC to be produced as a single component, as opposed to multiple components with many fabrication and assembly steps. In earlier experiments, surrogate materials were used to simulate the properties (specifically reactivity and density) of DU. Based on the positive results from those studies, the project participants decided that further evaluation of the issues and concerns that would accompany spraying DU was warranted. That evaluation occupied substantially all of Fiscal Year 1995, yielding conceptual designs for both an intermediate facility and a production facility and their associated engineering estimates. An intermediate facility was included in this study to allow further technology development in spraying DU. Although spraying DU to near-net shape seems to be feasible, a number of technical, engineering, and safety issues would need to be evaluated before proceeding with a production facility. This report is intended to document the results from the spray-casting project and to provide information needed by anyone interested in proceeding to the next step

  8. High pressure die casting of Fe-based metallic glass

    Ramasamy, Parthiban; Szabo, Attila; Borzel, Stefan; Eckert, Jürgen; Stoica, Mihai; Bárdos, András

    2016-01-01

    Soft ferromagnetic Fe-based bulk metallic glass key-shaped specimens with a maximum and minimum width of 25.4 and 5 mm, respectively, were successfully produced using a high pressure die casting (HPDC) method, The influence of die material, alloy temperature and flow rate on the microstructure, thermal stability and soft ferromagnetic properties has been studied. The results suggest that a steel die in which the molten metal flows at low rate and high temperature can be used to produce completely glassy samples. This can be attributed to the laminar filling of the mold and to a lower heat transfer coefficient, which avoids the skin effect in the steel mold. In addition, magnetic measurements reveal that the amorphous structure of the material is maintained throughout the key-shaped samples. Although it is difficult to control the flow and cooling rate of the molten metal in the corners of the key due to different cross sections, this can be overcome by proper tool geometry. The present results confirm that HPDC is a suitable method for the casting of Fe-based bulk glassy alloys even with complex geometries for a broad range of applications. PMID:27725780

  9. High pressure die casting of Fe-based metallic glass.

    Ramasamy, Parthiban; Szabo, Attila; Borzel, Stefan; Eckert, Jürgen; Stoica, Mihai; Bárdos, András

    2016-10-11

    Soft ferromagnetic Fe-based bulk metallic glass key-shaped specimens with a maximum and minimum width of 25.4 and 5 mm, respectively, were successfully produced using a high pressure die casting (HPDC) method, The influence of die material, alloy temperature and flow rate on the microstructure, thermal stability and soft ferromagnetic properties has been studied. The results suggest that a steel die in which the molten metal flows at low rate and high temperature can be used to produce completely glassy samples. This can be attributed to the laminar filling of the mold and to a lower heat transfer coefficient, which avoids the skin effect in the steel mold. In addition, magnetic measurements reveal that the amorphous structure of the material is maintained throughout the key-shaped samples. Although it is difficult to control the flow and cooling rate of the molten metal in the corners of the key due to different cross sections, this can be overcome by proper tool geometry. The present results confirm that HPDC is a suitable method for the casting of Fe-based bulk glassy alloys even with complex geometries for a broad range of applications.

  10. High pressure die casting of Fe-based metallic glass

    Ramasamy, Parthiban; Szabo, Attila; Borzel, Stefan; Eckert, Jürgen; Stoica, Mihai; Bárdos, András

    2016-10-01

    Soft ferromagnetic Fe-based bulk metallic glass key-shaped specimens with a maximum and minimum width of 25.4 and 5 mm, respectively, were successfully produced using a high pressure die casting (HPDC) method, The influence of die material, alloy temperature and flow rate on the microstructure, thermal stability and soft ferromagnetic properties has been studied. The results suggest that a steel die in which the molten metal flows at low rate and high temperature can be used to produce completely glassy samples. This can be attributed to the laminar filling of the mold and to a lower heat transfer coefficient, which avoids the skin effect in the steel mold. In addition, magnetic measurements reveal that the amorphous structure of the material is maintained throughout the key-shaped samples. Although it is difficult to control the flow and cooling rate of the molten metal in the corners of the key due to different cross sections, this can be overcome by proper tool geometry. The present results confirm that HPDC is a suitable method for the casting of Fe-based bulk glassy alloys even with complex geometries for a broad range of applications.

  11. Development of Thin Section Zinc Die Casting Technology

    Goodwin, Frank [International Lead Zinc Research Org., Inc., Durham, NC (United States)

    2013-10-31

    A new high fluidity zinc high pressure die casting alloy, termed the HF alloy, was developed during laboratory trials and proven in industrial production. The HF alloy permits castings to be achieved with section thicknesses of 0.3 mm or less. Technology transfer activities were conducted to develop usage of the HF high fluidity alloy. These included production of a brochure and a one-hour webinar on the HF alloy. The brochure was then sent to 1,184 product designers in the Interzinc database. There was excellent reception to this mailing, and from this initial contact 5 technology transfer seminars were conducted for 81 participants from 30 companies across a wide range of business sectors. Many of the successful applications to date involve high quality surface finishes. Design and manufacturing assistance was given for development of selected applications.

  12. Die casting copper motor rotors: mold materials and processing for cost-effective manufacturing

    Peters, D.T.; Cowie, J.G.; Brush, E.F. Jr.

    2000-07-01

    This project seeks to demonstrate mold materials for copper pressure die-casting that are cost-effective and practical for production use in die-casting copper motor rotors. The incorporation of die-cast copper for conductor bars and end rings of the induction motor in place of aluminum would result in attractive improvements in motor energy efficiency through reductions in motor losses ranging from 15% to 20%. Die-cast motor rotors are produced in aluminum today because rotor fabrication by pressure die-casting is an established practice. Lack of a durable and cost-effective mold material has been the technical barrier preventing manufacture of the die-cast copper rotor. This project tested H-13 steel die inserts that establish the baseline. Nickel-, tungsten-, and molybdenum-based high temperature alloys were extensively tested. Results indicate that substantially extended die life is possible using high temperature die materials, pre-heated and operated at elevated temperatures. Pre-heating and high operating temperatures were shown to be critical in extending the die life by decreasing the cyclic stresses associated with thermal expansion. Extended die life provides the opportunity for economically viable copper motor rotor die-casting. (orig.)

  13. Application of laser additive manufacturing to produce dies for aluminium high pressure die casting

    Pereira, MFVT

    2012-07-01

    Full Text Available through immersion in liquid aluminium. The dipping cycle closely resembles the heating and cooling cycle of a typical aluminium die under casting conditions. The suitability of any LAM technology, that can produce fully dense metallic components... cost vs wrought manufactured 5.2 1,7 2. 2 Average cost Very High Medium High Table 3: Processing and finishing costs of test coupons 3.1 Cyclic Immersion in Molten Aluminium Figure 3 below shows the testing apparatus developed to simulate...

  14. A 1-D Analytical Model for the Thermally Induced Stresses in the Mould Surface During Die Casting

    Hattel, Jesper; Hansen, Preben

    1994-01-01

    This paper presents an anlytically based method for predicting the normal stresses in a die mold surface exposed to a thermal load. A example of application of the method is the high-pressure di casting process where the surface stresses in critical cases lead to cracks. Expressions for the normal...... stresses as afunction of the thermal and mechanical properties have been developed for a casting both without and with a coating. Finally, the resulting relationships are derived and evaluated, with particular emphasis on the effect of the heat transfer coefficient between the casting and the mold....

  15. Modeling and Analysis of The Pressure Die Casting Using Response Surface Methodology

    Kittur, Jayant K.; Herwadkar, T. V.; Parappagoudar, M. B.

    2010-01-01

    Pressure die casting is successfully used in the manufacture of Aluminum alloys components for automobile and many other industries. Die casting is a process involving many process parameters having complex relationship with the quality of the cast product. Though various process parameters have influence on the quality of die cast component, major influence is seen by the die casting machine parameters and their proper settings. In the present work, non-linear regression models have been developed for making predictions and analyzing the effect of die casting machine parameters on the performance characteristics of die casting process. Design of Experiments (DOE) with Response Surface Methodology (RSM) has been used to analyze the effect of effect of input parameters and their interaction on the response and further used to develop nonlinear input-output relationships. Die casting machine parameters, namely, fast shot velocity, slow shot to fast shot change over point, intensification pressure and holding time have been considered as the input variables. The quality characteristics of the cast product were determined by porosity, hardness and surface rough roughness (output/responses). Design of experiments has been used to plan the experiments and analyze the impact of variables on the quality of casting. On the other-hand Response Surface Methodology (Central Composite Design) is utilized to develop non-linear input-output relationships (regression models). The developed regression models have been tested for their statistical adequacy through ANOVA test. The practical usefulness of these models has been tested with some test cases. These models can be used to make the predictions about different quality characteristics, for the known set of die casting machine parameters, without conducting the experiments.

  16. 77 FR 6587 - PHB Die Casting a Subsidiary of PHB, Inc., Including On-Site Leased Workers From Career Concepts...

    2012-02-08

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-64,292] PHB Die Casting a... 19, 2008, applicable to workers of PHB Die Casting, a subsidiary of PHB, Inc., including on-site... production of die castings. New information shows that a worker from Burns Industrial Group (BIG Inc) was...

  17. Vacuum die casting of silicon sheet for photovoltaic applications. First quarterly report, March 16-June 30, 1979

    None

    1979-01-01

    The obtective of this program is to develop a vacuum die-casting process for producing silicon sheet suitable for photovoltaic cells and to develop production techniques for optimization of polycrystallie silicon solar cell output. Efforts will examine process methods which are directed toward minimum cost processing of silicon into a quality suitable for producing solar cells with a terrestrial efficiency greater than 12% and having the potential to be scaled for large quantity production. In the vacuum die casting technique, silicon is melted under vacuum, and an evacuated die with a thin rectangular cavity is inserted into the melt. Liquid silicon is then injected into the die using a positive pressure of an inert gas. The major portion of the die casting work will be performed at Stanford Research Institute International under subcontract. The initial approach will follow parallel tracks: (1) obtain mechanical design parameters by using boron nitride, which has been shown to be non-wetting to silicon; (2) optimize silicon nitride material composition and coatings by sessile drop experiments; (3) test effectiveness of fluoride salt interfacial media with a graphite mold; and (4) test effect of surface finish using both boron nitride and graphite. Having established the material and mechanical boundary conditions, a finalized version of the prototype assembly will be constructed and the casting varibles determined. Polycrystalline silicon solar cells, with and without impurities, will be fabricated, characterized, and optimized at ARCCO Solar. The major activities will focus on the use of Wacker SILCO, HEM and in-house materials until vacuum die cast wafers are available. A baseline process with vacuum metallized contacts will be established and a reference mass production process with screen-printed metallization and high-throughput diffusions will also be obtained.

  18. [Cervical adaptation of complete cast crowns of various metal alloys, with and without die spacers].

    Stephano, C B; Roselino, R F; Roselino, R B; Campos, G M

    1989-01-01

    A metallic replica from a dental preparation for crown was used to make 8 class-IV stone dies. The wax patterns for the casting of the crowns were obtained in two conditions: a) from the stone die with no spacer; and b) from the stone die with an acrylic spacer. Thus, 64 metallic crowns were casted, using 4 different alloys: DURACAST (Cu-Al), NICROCAST (Ni-Cr) and DURABOND (Ni-Cr), and gold. The casted crowns were fitted in the metallic replica and measured as to the cervical discrepance of fitting. The results showed that the use of die spacers decreases the clinical discrepancies of fitting of the casted crowns (in a statistically significant level), no matter the metallic alloy employed.

  19. Ageless Aluminum-Cerium-Based Alloys in High-Volume Die Casting for Improved Energy Efficiency

    Stromme, Eric T.; Henderson, Hunter B.; Sims, Zachary C.; Kesler, Michael S.; Weiss, David; Ott, Ryan T.; Meng, Fanqiang; Kassoumeh, Sam; Evangelista, James; Begley, Gerald; Rios, Orlando

    2018-04-01

    Strong chemical reactions between Al and Ce lead to the formation of intermetallics with exceptional thermal stability. The rapid formation of intermetallics directly from the liquid phase during solidification of Al-Ce alloys leads to an ultrafine microconstituent structure that effectively strengthens as-cast alloys without further microstructural optimization via thermal processing. Die casting is a high-volume manufacturing technology that accounts for greater than 40% of all cast Al products, whereas Ce is highly overproduced as a waste product of other rare earth element (REE) mining. Reducing heat treatments would stimulate significant improvements in manufacturing energy efficiency, exceeding (megatonnes/year) per large-scale heat-treatment line. In this study, multiple compositions were evaluated with wedge mold castings to test the sensitivity of alloys to the variable solidification rate inherent in high-pressure die casting. Once a suitable composition was determined, it was successfully demonstrated at 800 lbs/h in a 600-ton die caster, after which the as-die cast parts performed similarly to ubiquitous A380 in the same geometry without requiring heat treatment. This work demonstrates the compatibility of Al REE alloys with high-volume die-casting applications with minimal heat treatments.

  20. Ageless Aluminum-Cerium-Based Alloys in High-Volume Die Casting for Improved Energy Efficiency

    Stromme, Eric T.; Henderson, Hunter B.; Sims, Zachary C.; Kesler, Michael S.; Weiss, David; Ott, Ryan T.; Meng, Fanqiang; Kassoumeh, Sam; Evangelista, James; Begley, Gerald; Rios, Orlando

    2018-06-01

    Strong chemical reactions between Al and Ce lead to the formation of intermetallics with exceptional thermal stability. The rapid formation of intermetallics directly from the liquid phase during solidification of Al-Ce alloys leads to an ultrafine microconstituent structure that effectively strengthens as-cast alloys without further microstructural optimization via thermal processing. Die casting is a high-volume manufacturing technology that accounts for greater than 40% of all cast Al products, whereas Ce is highly overproduced as a waste product of other rare earth element (REE) mining. Reducing heat treatments would stimulate significant improvements in manufacturing energy efficiency, exceeding (megatonnes/year) per large-scale heat-treatment line. In this study, multiple compositions were evaluated with wedge mold castings to test the sensitivity of alloys to the variable solidification rate inherent in high-pressure die casting. Once a suitable composition was determined, it was successfully demonstrated at 800 lbs/h in a 600-ton die caster, after which the as-die cast parts performed similarly to ubiquitous A380 in the same geometry without requiring heat treatment. This work demonstrates the compatibility of Al REE alloys with high-volume die-casting applications with minimal heat treatments.

  1. Kinetics of steel heavy ingot formation in dies of semicontinuous-casting machines

    Tsukerman, V.Ya.; Marchenko, I.K.

    1986-01-01

    Formation kinetics of round section ingot of up to 0.67 m in diameter was analyzed in dies of semicontinuous-casting machines on casting of the most usable assortment steels: medium-carbon low-alloyed and chromium-nickel stainless steels. It is established that solidification coefficient decreases in direct proportion to ingot diameter. Value of different-thickness ingot skin at die outlet is in direct proportion to a casted steel overheating temperature, ingot diameter and inversely proportional to the number and diameter of holes in a ladder nozzle and square root of ingot drawing rate

  2. SPH based modelling of oxide and oxide film formation in gravity die castings

    Ellingsen, K; M'Hamdi, M; Coudert, T

    2015-01-01

    Gravity die casting is an important casting process which has the capability of making complicated, high-integrity components for e.g. the automotive industry. Oxides and oxide films formed during filling affect the cast product quality. The Smoothed particle hydrodynamics (SPH) method is particularly suited to follow complex flows. The SPH method has been used to study filling of a gravity die including the formation and transport of oxides and oxide films for two different filling velocities. A low inlet velocity leads to a higher amount of oxides and oxide films in the casting. The study demonstrates the usefulness of the SPH method for an increased understanding of the effect of different filling procedures on the cast quality. (paper)

  3. Numerical modeling of the thickness dependence of zinc die-cast materials

    Page, Maria Angeles Martinez; Ruf, Matthias; Hartmann, Stefan

    2017-11-01

    Zinc die casting alloys show varying material properties over the thickness in their final solid state, which causes a change in the mechanical response for specimens with different thicknesses. In this article, we propose a modeling concept to account for the varying porosity in the constitutive modeling. The material properties are effectively incorporated by combining a partial differential equation describing the distribution of the pores by a structural parameter with the Mori-Tanaka approach for linear elasticity. The distribution of the porosity is determined by polished cut images, for which the procedure is explained in detail. Finite element simulations of the coupled system incorporating the thickness dependence show the applicability of this approach.

  4. 3D scanning based mold correction for planar and cylindrical parts in aluminum die casting

    Takashi Seno

    2015-04-01

    Full Text Available Aluminum die casting is an important manufacturing process for mechanical components. Die casting is known to be more accurate than other types of casting; however, post-machining is usually necessary to achieve the required accuracy. The goal of this investigation is to develop machining- free aluminum die casting. Improvement of the accuracy of planar and cylindrical parts is expected by correcting metal molds. In the proposed method, the shape of cast aluminum made with the initial metal molds is measured by 3D scanning. The 3D scan data includes information about deformations that occur during casting. Therefore, it is possible to estimate the deformation and correction amounts by comparing 3D scan data with product computer-aided design (CAD data. We corrected planar and cylindrical parts of the CAD data for the mold. In addition, we corrected the planar part of the metal mold using the corrected mold data. The effectiveness of the proposed method is demonstrated by evaluating the accuracy improvement of the cast aluminum made with the corrected mold.

  5. Numerical simulation and optimization of Al alloy cylinder body by low pressure die casting

    Mi Guofa

    2008-05-01

    Full Text Available Shrinkage defects can be formed easily at Critical location during low pressure die casting (LPDC of aluminum alloy cylinder body. It has harmful effect on the products. Mold fi lling and solidifi cation process of a cylinder body was simulated by using of Z-CAST software. The casting method was improved based on the simulation results. In order to create effective feeding passage, the structure of casting was modifi ed by changing the location of strengthening ribs at the bottom, without causing any adverse effect on the part’s performance. Inserting copper billet at suitable location of the die is a valid way to create suitable solidifi cation sequence that is benefi cial to the feeding. Using these methods, the shrinkage defect was completely eliminated at the critical location.

  6. Metallographic assessment of Al-12Si high-pressure die casting escalator steps.

    Vander Voort, George Frederic; Suárez-Peña, Beatriz; Asensio-Lozano, Juan

    2014-10-01

    A microstructural characterization study was performed on high-pressure die cast specimens extracted from escalator steps manufactured from an Al-12 wt.% Si alloy designed for structural applications. Black and white, color light optical imaging and scanning electron microscopy techniques were used to conduct the microstructural analysis. Most regions in the samples studied contained globular-rosette primary α-Al grains surrounded by an Al-Si eutectic aggregate, while primary dendritic α-Al grains were present in the surface layer. This dendritic microstructure was observed in the regions where the melt did not impinge directly on the die surface during cavity filling. Consequently, microstructures in the surface layer were nonuniform. Utilizing physical metallurgy principles, these results were analyzed in terms of the applied pressure and filling velocity during high-pressure die casting. The effects of these parameters on solidification at different locations of the casting are discussed.

  7. Corrosion behavior of die-cast Mg-4Al-2Sn-xCa alloy

    Park, Kyung Chul; Kim, Byeong Ho; Kim, Kyung Ro [Defence Agency for Technology and Quality, Jinju (Korea, Republic of); Cho, Dae Hyun; Park, Ik Min [Pusan National University, Busan (Korea, Republic of)

    2016-05-15

    In the present work, the effect of Ca additions on microstructure and corrosion characteristics of high pressure die-cast Mg-4Al-2Sn alloy has been investigated. Mg-4Al-2Sn-xCa (x= 0, 0.3 and 0.7wt.%) alloy was prepared by using a high pressure die-casting method. Results indicated that the microstructure of Mg-4Al-2Sn alloy consisted of α-Mg, Mg{sub 17}Al{sub 12} and Mg{sub 2}Sn phase. With increase of Ca additions, CaMgSn phase was newly formed and grain size was sharply decreased. From the test results, the corrosion resistance of die-cast Mg-4Al-2Sn alloy was significantly improved by Ca addition. It is considered that stabilization of Mg(OH){sub 2} layer and refinements of microstructure with increase of Ca additions.

  8. Failure behavior of high pressure die casting AZ91D magnesium alloy

    Li, X.; Xiong, S.M. [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Tsinghua University, Beijing 100084 (China); Guo, Z., E-mail: zhipeng_guo@mail.tsinghua.edu.cn [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Tsinghua University, Beijing 100084 (China)

    2016-08-30

    The failure behavior of high pressure die casting AZ91D magnesium alloy during both tensile and fatigue tests was studied in situ by using scanning electron microscope. Attention was focused on the role of microstructure played in crack initiation and propagation. Results showed that the defects in castings, including gas pore, shrinkage pore and defect band, were the crack initiation sources. In tensile test, the crack propagated in a combination of intergranular and transgranular modes, and the specimen fractured by connecting defects at the section with minimum effective force bearing area. In fatigue test, the crack propagated in a transgranular mode at specific crystalline planes. When the crack was in contact with the β-phase, the crack would pass through, and fracture the network β-phase, whereas bypass the island β-phase by detaching it from the surrounding α-Mg grains. Besides, defects in front of the crack would act as the secondary crack initiation sources, from which new cracks would initiate and propagate. With the propagation of the fatigue crack, the actual maximum cyclic stress would increase to the fracture stress of the left cross section and lead to the final fracture of the specimen.

  9. The simulation of magnesium wheel low pressure die casting based on PAM-CASTTM

    Peng Yinghong; Wang Yingchun; Li Dayong; Zeng Xiaoqin

    2004-01-01

    Magnesium is the lightest metal commonly used in engineering, with various excellent characteristics such as high strength and electromagnetic interference shielding capability. Particularly, the usage of magnesium in automotive industry can meet better the need to reduce fuel consumption and CO2 emissions. Nowadays, most current magnesium components in automobiles are made by die casting. In this paper, commercial software for die casting, PAM-CAST TM , was utilized to simulate the low pressure die casting process of magnesium wheel. Through calculating temperature field and velocity field during filling and solidification stages, the evolution of temperature distribution and liquid fraction was analyzed. Then, the potential defects including the gas entrapments in the middle of the spokes, shrinkages between the rim and the spokes were forecasted. The analytical results revealed that the mold geometry and die casting parameters should be improved in order to get the sound magnesium wheel. The reasons leading to these defects were also analyzed and the solutions to eliminate them were put forward. Furthermore, through reducing the pouring velocity, the air gas entrapments and partial shrinkages were eliminated effectively

  10. Microstructural analysis of the creep resistance of die-cast Mg-4Al-2RE alloy

    Zhu, S.M. [CAST CRC, Department of Materials Engineering, Monash University, Victoria 3800 (Australia)], E-mail: suming.zhu@eng.monash.edu.au; Gibson, M.A. [CAST CRC, CSIRO Materials Science and Engineering, Private Bag 33, Clayton South MDC, Clayton, Victoria 3169 (Australia); Nie, J.F.; Easton, M.A. [CAST CRC, Department of Materials Engineering, Monash University, Victoria 3800 (Australia); Abbott, T.B. [Advanced Magnesium Technologies, Milton, Queensland 4064 (Australia)

    2008-03-15

    The microstructure and microstructural stability of die-cast AE42 (Mg-4Al-2RE) alloy were investigated by transmission electron microscopy. It is shown that the formation of Mg{sub 17}Al{sub 12} after ageing at 200 deg. C is not due to the decomposition of A1{sub 11}RE{sub 3} as reported in the literature, but, rather, is associated with the supersaturation of Al solute in the {alpha}-Mg matrix. The level of Al solute retained in the {alpha}-Mg matrix after die-casting is suggested to be an important factor in influencing creep resistance.

  11. Mortality among workers in a die-casting and electroplating plant.

    Silverstein, M; Mirer, F; Kotelchuck, D; Silverstein, B; Bennett, M

    1981-01-01

    A proportional mortality and case-referent analysis of 238 deaths among hourly employees in an automobile hardware manufacturing plant was conducted. The major operations of the plant were zinc die casting and electroplating. Chemical exposure included die-casting emissions and mists from chrome and nickel plating. The chief proportional mortality finding was a significant excess of lung cancer among both white men and women. A case-referent analysis indicated a possible association between lung cancer and work in certain departments. The findings support the hypothesis of a work-related carcinogenic risk. Follow-up recommendations have been made.

  12. Advanced Lost Foam Casting Technology; FINAL

    Charles E. Bates; Harry E. Littleton; Don Askeland; Taras Molibog; Jason Hopper; Ben Vatankhah

    2000-01-01

    This report describes the research done under the six tasks to improve the process and make it more functional in an industrial environment. Task 1: Pattern Pyrolysis Products and Pattern Properties Task 2: Coating Quality Control Task 3: Fill and Solidification Code Task 4: Alternate Pattern Materials Task 5: Casting Distortion Task 6: Technology Transfer

  13. Optimization of Composition and Heat Treating of Die Steels for Extended Lifetime; FINAL

    David Schwam; John F, Wallace; Quanyou Zhou

    2002-01-01

    An ''average'' die casting die costs fifty thousand dollars. A die used in making die cast aluminum engine blocks can cost well over one million dollars. These costs provide a strong incentive for extension of die life. While vacuum quenched Premium Grade H13 dies have become the most widely used in the United States, tool makers and die casters are constantly searching for new steels and heat treating procedures to extend die life. This project was undertaken to investigate the effects of composition and heat treating on die life and optimize these parameters

  14. Metallic Reinforcement of Direct Squeeze Die Casting Aluminum Alloys for Improved Strength and Fracture Resistance

    D. Schwam: J.F. Wallace: Y. Zhu: J.W. Ki

    2004-10-01

    The utilization of aluminum die casting as enclosures where internal equipment is rotating inside of the casting and could fracture requires a strong housing to restrain the fractured parts. A typical example would be a supercharger. In case of a failure, unless adequately contained, fractured parts could injure people operating the equipment. A number of potential reinforcement materials were investigated. The initial work was conducted in sand molds to create experimental conditions that promote prolonged contact of the reinforcing material with molten aluminum. Bonding of Aluminum bronze, Cast iron, and Ni-resist inserts with various electroplated coatings and surface treatments were analyzed. Also toughening of A354 aluminum cast alloy by steel and stainless steel wire mesh with various conditions was analyzed. A practical approach to reinforcement of die cast aluminum components is to use a reinforcing steel preform. Such performs can be fabricated from steel wire mesh or perforated metal sheet by stamping or deep drawing. A hemispherical, dome shaped casting was selected in this investigation. A deep drawing die was used to fabricate the reinforcing performs. The tendency of aluminum cast enclosures to fracture could be significantly reduced by installing a wire mesh of austenitic stainless steel or a punched austenitic stainless steel sheet within the casting. The use of reinforcements made of austenitic stainless steel wire mesh or punched austenitic stainless steel sheet provided marked improvement in reducing the fragmentation of the casting. The best strengthening was obtained with austenitic stainless steel wire and with a punched stainless steel sheet without annealing this material. Somewhat lower results were obtained with the annealed punched stainless steel sheet. When the annealed 1020 steel wire mesh was used, the results were only slightly improved because of the lower mechanical properties of this unalloyed steel. The lowest results were

  15. Simulation of distortion and residual stress in high pressure die casting – modelling and experiments

    Hofer, P; Kaschnitz, E; Schumacher, P

    2012-01-01

    Two individual high-pressure die-casting geometries were developed in order to study the influence of process parameters and different alloys on the distortion behaviour of castings. These geometries were a stress lattice and a V-shaped sample tending to form residual stress due to different wall thickness respectively by a deliberate massive gating system. In the experimental castings the influence of the most important process parameters such as die temperature and die opening time and the cooling regime was examined. The time evolution of process temperatures was measured using thermal imaging. The heat transfer coefficients were adapted to the observed temperature distributions. Castings were produced from the two alloys AlSi12 and AlSi10MnMg. The distortion of the castings was measured by means of a tactile measuring device. For the alloy AlSi10MnMg thermo-physical and thermo-mechanical data were obtained using differential scanning calorimetry, laser flash technique, dilatometry and tensile testing at elevated temperatures. These data were used for modelling the material behaviour of the AlSi10MnMg alloy in the numerical model while for the alloy AlSi12(Fe) literature data were used. Process and stress simulation were conducted using the commercial FEM software ANSYS Workbench. A survey on the results of the comparison between simulation and experiment is given for both alloys.

  16. Study on interfacial heat transfer coefficient at metal/die interface during high pressure die casting process of AZ91D alloy

    GUO Zhi-peng

    2007-02-01

    Full Text Available The high pressure die casting (HPDC process is one of the fastest growing and most efficient methods for the production of complex shape castings of magnesium and aluminum alloys in today’s manufacturing industry.In this study, a high pressure die casting experiment using AZ91D magnesium alloy was conducted, and the temperature profiles inside the die were Measured. By using a computer program based on solving the inverse heat problem, the metal/die interfacial heat transfer coefficient (IHTC was calculated and studied. The results show that the IHTC between the metal and die increases right after the liquid metal is brought into the cavity by the plunger,and decreases as the solidification process of the liquid metal proceeds until the liquid metal is completely solidified,when the IHTC tends to be stable. The interfacial heat transfer coefficient shows different characteristics under different casting wall thicknesses and varies with the change of solidification behavior.

  17. Inventory of pollution reduction options for an aluminium pressure die casting plant

    Neto, B.A.F.; Kroeze, C.; Hordijk, L.; Costa, C.

    2009-01-01

    This study presents an overview of options aiming to reduce emissions to air, soil and water from an aluminium die casting plant located in Portugal. We identify eighteen pollution reduction options and then estimate their potential to reduce the pollution, and the costs associated with their

  18. Low cycle fatigue behavior of die cast Mg-Al-Mn-Ce magnesium alloy

    Wu Wei

    2013-11-01

    Full Text Available Fatigue failure is a main failure mode for magnesium and other alloys. It is beneficial for fatigue design and fatigue life improvement to investigate the low cycle fatigue behavior of magnesium alloys. In order to investigate the low cycle fatigue behavior of die cast Mg-Al-Mn-Ce magnesium alloy, the strain controlled fatigue experiments were performed at room temperature and fatigue fracture surfaces of specimens were observed with scanning election microscopy for the alloys under die-cast and aged states. Cyclic stress response curves, strain amplitude versus reversals to failure curve, total strain amplitude versus fatigue life curves and cyclic stress-strain curves of Mg-Al-Mn-Ce alloys were analyzed. The results show that the Mg-Al-Mn-Ce alloys under die-cast (F and aged (T5 states exhibit cyclic strain hardening under the applied total strain amplitudes, and aging treatment could greatly increase the cyclic stress amplitudes of die cast Mg-Al-Mn-Ce alloys. The relationships between the plastic strain amplitude, the elastic strain amplitude and reversals to failure of Mg-Al-Mn-Ce magnesium alloy under different treatment states could be described by Coffin-Manson and Basquin equations, respectively. Observations on the fatigue fracture surface of specimens reveal that the fatigue cracks initiate on the surface of specimens and propagate transgranularly.

  19. Strategies to reduce the environmental impact of an aluminium pressure die casting plant: A scenario analysis

    Neto, B.; Kroeze, C.; Hordijk, L.; Costa, C.; Pulles, M.P.J.

    2009-01-01

    This study explores a model (MIKADO) to analyse scenarios for the reduction of the environmental impact of an aluminium die casting plant. Our model calculates the potential to reduce emissions, and the costs associated with implementation of reduction options. In an earlier paper [Neto, B., Kroeze,

  20. Semi-solid high pressure die casting of metal matrix composites produced by liquid state processing

    Ivanchev, L

    2012-10-01

    Full Text Available stirring. The composite was then transferred to a High Pressure Die Casting (HPDC) machine in the semi-solid state. The micron size particles were found to be predominantly in the intergranular eutectic while the nano-particles were predominantly...

  1. Age hardening in die-cast Mg–Al–RE alloys due to minor Mn additions

    Zhu, S.M., E-mail: suming.zhu@rmit.edu.au [School Engineering, RMIT University, Carlton, Victoria 3053 (Australia); Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); Abbott, T.B. [School Engineering, RMIT University, Carlton, Victoria 3053 (Australia); Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); Magontec Limited, Sydney, New South Wales 2000 (Australia); Gibson, M.A. [School Engineering, RMIT University, Carlton, Victoria 3053 (Australia); Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); CSIRO Manufacturing Flagship, Clayton, Victoria 3168 (Australia); Nie, J.F. [Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); Easton, M.A. [School Engineering, RMIT University, Carlton, Victoria 3053 (Australia)

    2016-02-22

    Die-cast Mg–Al–rare earth (RE) alloys are normally used in the as-cast condition without the application of heat treatment because it is a common perception that heat treatment will not provide benefit to these alloys. This paper reports, for the first time, that enhanced age hardenability can be achieved in die-cast Mg–Al–RE alloys with minor Mn additions. For example, the yield strength of Mg–4 wt%Al–3 wt%La alloy with 0.32 wt% Mn is increased by ∼34 MPa (∼26%) after ageing at 200 °C for 32 h (T5). The enhanced age hardenability is associated with the precipitation of nanoscale Al–Mn particles during ageing.

  2. Simulation of Stress Distribution in a Thick- Walled Bushing Produced by Die-Casting

    Pisarek B.P.

    2017-12-01

    Full Text Available Metallographic investigations and a computer simulation of stresses in a gravity die-casting bushing were performed. Simulation of the casting process, solidification of the thick-walled bushing and calculations of the stress was performed using MAGMA5.3 software. The size variability of phases κII affecting the formation of phase stresses σf, depending on the location of the metallographic test area, was identified. The distribution of thermal σt and shrinkage stresses σs, depending on the location of the control point SC in the bushing's volume, was estimated. Probably the nature of these stresses will change slightly even after machining. This can cause variations in operating characteristics (friction coefficient, wear. Due to the strong inhomogeneity of the stress distribution in the bushing's casting, it is necessary to perform further tests of the possibility to conduct thermal treatment guaranteeing homogenization of the internal stresses in the casting, as well as to introduce changes in the bushing' s construction and the casting technology. The paper presents the continuation of the results of research aimed at identifying the causes of defects in the thick-walled bushing, die-casting made of CuAl10Fe5Ni5Cr aluminium bronze.

  3. Tribological Properties of AlSi11-SiCp Composite Castings Produced by Pressure Die Casting Method

    Konopka Z.

    2014-08-01

    Full Text Available The measurement results concerning the abrasive wear of AlSi11-SiC particles composites are presented in paper. The method of preparing a composite slurry composed of AlSi11 alloy matrix and 10, 20% vol.% of SiC particles, as well as the method of its high-pressure die casting was described. Composite slurry was injected into metal mould of cold chamber pressure die cast machine and castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. Very good uniform arrangement of SiC particles in volume composite matrix was observed and these results were publicated early in this journal. The kinetics of abrasive wear and correlation with SiC particles arrangement in composite matrix were presented. Better wear resistance of composite was observed in comparison with aluminium alloy. Very strong linear correlation between abrasive wear and particle arrangement was observed. The conclusion gives the analysis and the interpretation of the obtained results.

  4. Modeling of microstructure evolution of magnesium alloy during the high pressure die casting process

    Wu Mengwu; Xiong Shoumei

    2012-01-01

    Two important microstructure characteristics of high pressure die cast magnesium alloy are the externally solidified crystals (ESCs) and the fully divorced eutectic which form at the filling stage of the shot sleeve and at the last stage of solidification in the die cavity, respectively. Both of them have a significant influence on the mechanical properties and performance of magnesium alloy die castings. In the present paper, a numerical model based on the cellular automaton (CA) method was developed to simulate the microstructure evolution of magnesium alloy during cold-chamber high pressure die casting (HPDC) process. Modeling of dendritic growth of magnesium alloy with six-fold symmetry was achieved by defining a special neighbourhood configuration and calculating of the growth kinetics from complete solution of the transport equations. Special attention was paid to establish a nucleation model considering both of the nucleation of externally solidified crystals in the shot sleeve and the massive nucleation in the die cavity. Meanwhile, simulation of the formation of fully divorced eutectic was also taken into account in the present CA model. Validation was performed and the capability of the present model was addressed by comparing the simulated results with those obtained by experiments.

  5. Mathematical modeling of porosity formation in die cast A356 wheels

    Maijer, D.; Cockcroft, S.L.; Wells, M.A.; Luciuk, T.; Hermesmann, C.

    2000-01-01

    In an effort to leverage recent advances in modeling and process simulation tools, a mathematical model has been developed to predict porosity formation in die cast A356 wheels as part of a collaborative research agreement between researchers at the University of British Columbia and Canadian Autoparts Toyota Incorporated. The heat transfer model represents a three-dimensional, 30 o , slice of the wheel and die and is based on the commercial finite element code ABAQUS. Extensive temperature measurements in the die and in the wheel taken over several cycles in the casting process were used to fine tune and validate the model. Initial work on predicting porosity formation has focused on using the Niyama parameter as a measure of the probability of porosity. To date Niyama porosity predictions agree well with plant experience and show promise for reducing losses associated with porosity. (author)

  6. Tribological and Wear Performance of Nanocomposite PVD Hard Coatings Deposited on Aluminum Die Casting Tool

    Jose Mario Paiva

    2018-02-01

    Full Text Available In the aluminum die casting process, erosion, corrosion, soldering, and die sticking have a significant influence on tool life and product quality. A number of coatings such as TiN, CrN, and (Cr,AlN deposited by physical vapor deposition (PVD have been employed to act as protective coatings due to their high hardness and chemical stability. In this study, the wear performance of two nanocomposite AlTiN and AlCrN coatings with different structures were evaluated. These coatings were deposited on aluminum die casting mold tool substrates (AISI H13 hot work steel by PVD using pulsed cathodic arc evaporation, equipped with three lateral arc-rotating cathodes (LARC and one central rotating cathode (CERC. The research was performed in two stages: in the first stage, the outlined coatings were characterized regarding their chemical composition, morphology, and structure using glow discharge optical emission spectroscopy (GDOES, scanning electron microscopy (SEM, and X-ray diffraction (XRD, respectively. Surface morphology and mechanical properties were evaluated by atomic force microscopy (AFM and nanoindentation. The coating adhesion was studied using Mersedes test and scratch testing. During the second stage, industrial tests were carried out for coated die casting molds. In parallel, tribological tests were also performed in order to determine if a correlation between laboratory and industrial tests can be drawn. All of the results were compared with a benchmark monolayer AlCrN coating. The data obtained show that the best performance was achieved for the AlCrN/Si3N4 nanocomposite coating that displays an optimum combination of hardness, adhesion, soldering behavior, oxidation resistance, and stress state. These characteristics are essential for improving the die mold service life. Therefore, this coating emerges as a novelty to be used to protect aluminum die casting molds.

  7. Tribological and Wear Performance of Nanocomposite PVD Hard Coatings Deposited on Aluminum Die Casting Tool.

    Paiva, Jose Mario; Fox-Rabinovich, German; Locks Junior, Edinei; Stolf, Pietro; Seid Ahmed, Yassmin; Matos Martins, Marcelo; Bork, Carlos; Veldhuis, Stephen

    2018-02-28

    In the aluminum die casting process, erosion, corrosion, soldering, and die sticking have a significant influence on tool life and product quality. A number of coatings such as TiN, CrN, and (Cr,Al)N deposited by physical vapor deposition (PVD) have been employed to act as protective coatings due to their high hardness and chemical stability. In this study, the wear performance of two nanocomposite AlTiN and AlCrN coatings with different structures were evaluated. These coatings were deposited on aluminum die casting mold tool substrates (AISI H13 hot work steel) by PVD using pulsed cathodic arc evaporation, equipped with three lateral arc-rotating cathodes (LARC) and one central rotating cathode (CERC). The research was performed in two stages: in the first stage, the outlined coatings were characterized regarding their chemical composition, morphology, and structure using glow discharge optical emission spectroscopy (GDOES), scanning electron microscopy (SEM), and X-ray diffraction (XRD), respectively. Surface morphology and mechanical properties were evaluated by atomic force microscopy (AFM) and nanoindentation. The coating adhesion was studied using Mersedes test and scratch testing. During the second stage, industrial tests were carried out for coated die casting molds. In parallel, tribological tests were also performed in order to determine if a correlation between laboratory and industrial tests can be drawn. All of the results were compared with a benchmark monolayer AlCrN coating. The data obtained show that the best performance was achieved for the AlCrN/Si₃N₄ nanocomposite coating that displays an optimum combination of hardness, adhesion, soldering behavior, oxidation resistance, and stress state. These characteristics are essential for improving the die mold service life. Therefore, this coating emerges as a novelty to be used to protect aluminum die casting molds.

  8. Development of Integrated Die Casting Process for Large Thin-Wall Magnesium Applications

    Carter, Jon T. [General Motors LLC, Warren, MI (United States); Wang, Gerry [Meridian Lightweight Technologies, Plymouth MI (United States); Luo, Alan [General Motors LLC, Warren, MI (United States)

    2017-11-29

    The purpose of this project was to develop a process and product which would utilize magnesium die casting and result in energy savings when compared to the baseline steel product. The specific product chosen was a side door inner panel for a mid-size car. The scope of the project included: re-design of major structural parts of the door, design and build of the tooling required to make the parts, making of parts, assembly of doors, and testing (both physical and simulation) of doors. Additional work was done on alloy development, vacuum die casting, and overcasting, all in order to improve the performance of the doors and reduce cost. The project achieved the following objectives: 1. Demonstrated ability to design a large thin-wall magnesium die casting. 2. Demonstrated ability to manufacture a large thin-wall magnesium die casting in AM60 alloy. 3. Tested via simulations and/or physical tests the mechanical behavior and corrosion behavior of magnesium die castings and/or lightweight experimental automotive side doors which incorporate a large, thin-wall, powder coated, magnesium die casting. Under some load cases, the results revealed cracking of the casting, which can be addressed with re-design and better material models for CAE analysis. No corrosion of the magnesium panel was observed. 4. Using life cycle analysis models, compared the energy consumption and global warming potential of the lightweight door with those of a conventional steel door, both during manufacture and in service. Compared to a steel door, the lightweight door requires more energy to manufacture but less energy during operation (i.e., fuel consumption when driving vehicle). Similarly, compared to a steel door, the lightweight door has higher global warming potential (GWP) during manufacture, but lower GWP during operation. 5. Compared the conventional magnesium die casting process with the “super-vacuum” die casting process. Results achieved with cast tensile bars suggest some

  9. Analysis of the Causes of Cracks in a Thick-Walled Bush Made of Die-Cast Aluminum Bronze

    Pisarek B.P.

    2016-12-01

    Full Text Available For the die casting conditions of aluminium bronzes assumed based on the literature data, a thick-walled bush was cast, made of complex aluminium bronze (Cu-Al-Fe-Ni-Cr. After the cast was removed from the mould, cracks were observed inside it. In order to identify the stage in the technological production process at which, potentially, the formation of stresses damaging the continuity of the microstructure created in the cast was possible (hot cracking and/or cold cracking, a computer simulation was performed. The article presents the results of the computer simulation of the process of casting the material into the gravity die as well as solidifying and cooling of the cast in the shape of a thick-walled bush. The simulation was performed with the use of the MAGMA5 program and by application of the CuAl10Ni5,5Fe4,5 alloy from the MAGMA5 program database. The results were compared with the location of the defects identified in the actual cast. As a result of the simulation of the die-casting process of this bush, potential regions were identified where significant principal stresses accumulate, which can cause local hot and cold cracking. Until now, no research has been made of die-cast aluminium bronzes with a Cr addition. Correlating the results of the computer simulation validated by the analysis of the actual cast made it possible to clearly determine the critical regions in the cast exposed to cracking and point to the causes of its occurrence. Proposals of changes in the bush die casting process were elaborated, in order to avoid hot tearing and cold cracking. The article discusses the results of preliminary tests being a prologue to the optimization of the die-casting process parameters of complex aluminium bronze thick-walled bushs.

  10. Assessment of Computer Simulation Software and Process Data for High Pressure Die Casting of Magnesium

    Sabau, Adrian S [ORNL; Hatfield, Edward C [ORNL; Dinwiddie, Ralph Barton [ORNL; Kuwana, Kazunori [University of Kentucky; Viti, Valerio [University of Kentucky, Lexington; Hassan, Mohamed I [University of Kentucky, Lexington; Saito, Kozo [University of Kentucky

    2007-09-01

    Computer software for the numerical simulation of solidification and mold filling is an effective design tool for cast structural automotive magnesium components. A review of commercial software capabilities and their validation procedures was conducted. Aside form the software assessment, the program addressed five main areas: lubricant degradation, lubricant application, gate atomization, and heat transfer at metal mold interfaces. A test stand for lubricant application was designed. A sensor was used for the direct measurement of heat fluxes during lubricant application and casting solidification in graphite molds. Spray experiments were conducted using pure deionized water and commercial die lubricants. The results show that the sensor can be used with confidence for measuring heat fluxes under conditions specific to the die lube application. The data on heat flux was presented in forms suitable for use in HPDC simulation software. Severe jet breakup and atomization phenomena are likely to occur due to high gate velocities in HPDC. As a result of gate atomization, droplet flow affects the mold filling pattern, air entrapment, skin formation, and ensuing defects. Warm water analogue dies were designed for obtaining experimental data on mold filling phenomena. Data on break-up jet length, break-up pattern, velocities, and droplet size distribution were obtained experimentally and was used to develop correlations for jet break-up phenomena specific to die casting gate configurations.

  11. Energy Saving Melting and Revert Reduction Technology: Melting Efficiency in Die Casting Operations

    David Schwam

    2012-12-15

    This project addressed multiple aspects of the aluminum melting and handling in die casting operations, with the objective of increasing the energy efficiency while improving the quality of the molten metal. The efficiency of melting has always played an important role in the profitability of aluminum die casting operations. Consequently, die casters need to make careful choices in selecting and operating melting equipment and procedures. The capital cost of new melting equipment with higher efficiency can sometimes be recovered relatively fast when it replaces old melting equipment with lower efficiency. Upgrades designed to improve energy efficiency of existing equipment may be well justified. Energy efficiency is however not the only factor in optimizing melting operations. Melt losses and metal quality are also very important. Selection of melting equipment has to take into consideration the specific conditions at the die casting shop such as availability of floor space, average quantity of metal used as well as the ability to supply more metal during peaks in demand. In all these cases, it is essential to make informed decisions based on the best available data.

  12. The effect of equipment efficiency on occurrence of non-conforming products in die casting

    S. Borkowski

    2010-01-01

    Full Text Available This study focuses on determination of the relationships between equipment efficiency in casting machines and the level of quality. The determination was made based on coefficients of Total Productive Maintenance and r correlation coefficient. The degree at which break-downs and downtime affect the occurrence of non-conforming products was also evaluated. The goal of further investigations is to deter-mine the structure of downtime and finding which downtime types have greatest impact on the quality of die-casting products.

  13. Marginal adaptation of four inlay casting waxes on stone, titanium, and zirconia dies.

    Michalakis, Konstantinos X; Kapsampeli, Vassiliki; Kitsou, Aikaterini; Kirmanidou, Yvone; Fotiou, Anna; Pissiotis, Argirios L; Calvani, Pasquale Lino; Hirayama, Hiroshi; Kudara, Yukio

    2014-07-01

    Different inlay casting waxes do not produce copings with satisfactory marginal accuracy when used on different die materials. The purpose of this study was to evaluate the marginal accuracy of 4 inlay casting waxes on stone dies and titanium and zirconia abutments and to correlate the findings with the degree of wetting between the die specimens and the inlay casting waxes. The inlay casting waxes tested were Starwax (Dentaurum), Unterziehwachs (Bredent), SU Esthetic wax (Schuler), and Sculpturing wax (Renfert). The marginal opening of the waxes was measured with a stereomicroscope on high-strength stone dies and on titanium and zirconia abutments. Photographic images were obtained, and the mean marginal opening for each specimen was calculated. A total of 1440 measurements were made. Wetting between die materials and waxes was determined after fabricating stone, titanium, and zirconia rectangular specimens. A calibrated pipette was used to place a drop of molten wax onto each specimen. The contact angle was calculated with software after an image of each specimen had been made with a digital camera. Collected data were subjected to a 2-way analysis of variance (α=.05). Any association between marginal accuracy and wetting of different materials was found by using the Pearson correlation. The wax factor had a statistically significant effect both on the marginal discrepancy (F=158.31, P<.001) and contact angle values (F=68.09, P<.001). A statistically significant effect of the die material factor both on the marginal adaptation (F=503.47, P<.001) and contact angle values (F=585.02, P<.001) was detected. A significant correlation between the marginal accuracy and the contact angle values (Pearson=0.881, P=.01) was also found. Stone dies provided wax copings with the best marginal integrity, followed by titanium and zirconia abutments. Unterziehwachs (Bredent), wax produced the best marginal adaptation on different die materials. A significant correlation was found

  14. Development of materials for the rapid manufacture of die cast tooling

    Hardro, Peter Jason

    The focus of this research is to develop a material composition that can be processed by rapid prototyping (RP) in order to produce tooling for the die casting process. Where these rapidly produced tools will be superior to traditional tooling production methods by offering one or more of the following advantages: reduced tooling cost, shortened tooling creation time, reduced man-hours for tool creation, increased tool life, and shortened die casting cycle time. By utilizing RP's additive build process and vast material selection, there was a prospect that die cast tooling may be produced quicker and with superior material properties. To this end, the material properties that influence die life and cycle time were determined, and a list of materials that fulfill these "optimal" properties were highlighted. Physical testing was conducted in order to grade the processability of each of the material systems and to optimize the manufacturing process for the downselected material system. Sample specimens were produced and microscopy techniques were utilized to determine a number of physical properties of the material system. Additionally, a benchmark geometry was selected and die casting dies were produced from traditional tool materials (H13 steel) and techniques (machining) and from the newly developed materials and RP techniques (selective laser sintering (SLS) and laser engineered net shaping (LENS)). Once the tools were created, a die cast alloy was selected and a preset number of parts were shot into each tool. During tool creation, the manufacturing time and cost was closely monitored and an economic model was developed to compare traditional tooling to RP tooling. This model allows one to determine, in the early design stages, when it is advantageous to implement RP tooling and when traditional tooling would be best. The results of the physical testing and economic analysis has shown that RP tooling is able to achieve a number of the research objectives, namely

  15. Dislocation analysis of die-cast Mg-Al-Ca alloy after creep deformation

    Terada, Yoshihiro; Itoh, Daigo; Sato, Tatsuo

    2009-01-01

    Tensile creep tests were combined with detailed transmission electron microscopy in order to characterize the dislocation movements during creep and to explain the creep properties of the Mg-Al-Ca AX52 die-cast alloy at 473 K and stresses from 15 to 70 MPa. TEM observations indicate that dislocations are generated within the primary α-Mg grain in the die-casting process, which consist of both the basal and non-basal segments. The basal segments of dislocations are able to bow out and glide on the basal planes under the influence of a stress, and the jogs follow the basal segments with the help of climb during creep. The creep mechanism for the alloy is deduced as dislocation climb due to the formation of sub-boundaries during creep, while the easy glide of the basal segments of dislocations is controlling the creep rates immediately after the stress application of creep tests.

  16. Influence of refining process on the porosity of high pressure die casting alloy Al-Si

    A.W. Orlowicz

    2009-04-01

    Full Text Available This study presents research results of the influence that refining and transfer of AlSi12S alloy on the porosity of high pressure diecastings.Tests were conducted under production conditions of Die-casting Foundry META-ZEL Sp z o.o. The operation of refining was conducted in a melting furnace, with the use of an FDU Mini Degasser. Decay of the refining effect was assessed by evaluating the porosity content and metallographic examination.

  17. Casting Technology.

    Wright, Michael D.; And Others

    1992-01-01

    Three articles discuss (1) casting technology as it relates to industry, with comparisons of shell casting, shell molding, and die casting; (2) evaporative pattern casting for metals; and (3) high technological casting with silicone rubber. (JOW)

  18. Thermal Stress Analysis for Ceramics Stalk in the Low Pressure Die Casting Machine

    Noda, Nao-Aki; Hendra, Nao-Aki; Takase, Yasushi; Li, Wenbin

    Low pressure die casting (LPDC) is defined as a net shape casting technology in which the molten metal is injected at high speeds and pressure into a metallic die. The LPDC process is playing an increasingly important role in the foundry industry as a low-cost and high-efficiency precision forming technique. The LPDC process is that the permanent die and filling systems are placed over the furnace containing the molten alloy. The filling of the cavity is obtained by forcing the molten metal by means of a pressurized gas in order to rise into a ceramic tube, which connects the die to the furnace. The ceramics tube called stalk has high temperature resistance and high corrosion resistance. However, attention should be paid to the thermal stress when the stalk is dipped into the molten aluminum. It is important to develop the design of the stalk to reduce the risk of fracture because of low fracture toughness of ceramics. In this paper, therefore, the finite element method is applied to calculate the thermal stresses when the stalk is dipped into the crucible by varying the dipping speeds and dipping directions. It is found that the thermal stress can be reduced by dipping slowly if the stalk is dipped into the crucible vertically, while the thermal stress can be reduced by dipping fast if it is dipped horizontally.

  19. Energy Saving Melting and Revert Reduction Technology: Improved Die Casting Process to Preserve the Life of the Inserts

    David Schwam, PI; Xuejun Zhu, Sr. Research Associate

    2012-09-30

    The goal of this project was to study the combined effects of die design, proper internal cooling and efficient die lubricants on die life. The project targeted improvements in die casting insert life by: Optomized Die Design for Reduced Surface Temperature: The life of die casting dies is significantly shorter when the die is exposed to elevated temperature for significant periods of time. Any die operated under conditions leading to surface temperature in excess of 1050oF undergoes structural changes that reduce its strength. Optimized die design can improve die life significantly. This improvement can be accomplished by means of cooling lines, baffles and bubblers in the die. A key objective of the project was to establish criteria for the minimal distance of the cooling lines from the surface. This effort was supported with alloys and machining by BohlerUddeholm, Dunn Steel, HH Stark and Rex Buckeye. In plant testing and evaluation was conducted as in-kind cost share at St. Clair Die Casting. The Uddeholm Dievar steel evaluated in this program showed superior resistance to thermal fatigue resistance. Based on the experimental evidence, cooling lines could be placed as close as 0.5" from the surface. Die Life Extension by Optimized Die Lubrication: The life of die casting dies is affected by additions made to its surface with the proper lubricants. These lubricants will protect the surface from the considerable temperature peaks that occur when the molten melt enters the die. Dies will reach a significantly higher temperature without this lubricant being applied. The amount and type of the lubricant are critical variables in the die casting process. However, these lubricants must not corrode the die surface. This effort was supported with alloys and machining by BohlerUddeholm, Dunn Steel, HH Stark and Rex Buckeye. In plant testing and evaluation was conducted as in-kind cost share at St. Clair Die Casting. Chem- Trend participated in the program with die

  20. An establish attempt of reasons of machining splinter formation in AC44200 alloy high pressure die castings

    J. Mutwil

    2008-01-01

    A problem of splinter formation during machining the AC44200 alloy high pressure die casting has been experimental investigated. Inorder to establish the reason of this occurrence a set of 200 high pressure die casting of the tensile strength samples have been prepared. The tensile tests were carried out using a Zwick Z050 universal testing machine. JM-SPC program has been used for statistical analysis of test results. A large variability of tensile strength results has been found. In order t...

  1. Development of High-Performance Cast Crankshafts. Final Technical Report

    Bauer, Mark E [General Motors, Detroit, MI (United States)

    2017-03-31

    The objective of this project was to develop technologies that would enable the production of cast crankshafts that can replace high performance forged steel crankshafts. To achieve this, the Ultimate Tensile Strength (UTS) of the new material needs to be 850 MPa with a desired minimum Yield Strength (YS; 0.2% offset) of 615 MPa and at least 10% elongation. Perhaps more challenging, the cast material needs to be able to achieve sufficient local fatigue properties to satisfy the durability requirements in today’s high performance gasoline and diesel engine applications. The project team focused on the development of cast steel alloys for application in crankshafts to take advantage of the higher stiffness over other potential material choices. The material and process developed should be able to produce high-performance crankshafts at no more than 110% of the cost of current production cast units, perhaps the most difficult objective to achieve. To minimize costs, the primary alloy design strategy was to design compositions that can achieve the required properties with minimal alloying and post-casting heat treatments. An Integrated Computational Materials Engineering (ICME) based approach was utilized, rather than relying only on traditional trial-and-error methods, which has been proven to accelerate alloy development time. Prototype melt chemistries designed using ICME were cast as test specimens and characterized iteratively to develop an alloy design within a stage-gate process. Standard characterization and material testing was done to validate the alloy performance against design targets and provide feedback to material design and manufacturing process models. Finally, the project called for Caterpillar and General Motors (GM) to develop optimized crankshaft designs using the final material and manufacturing processing path developed. A multi-disciplinary effort was to integrate finite element analyses by engine designers and geometry-specific casting

  2. A process chain for integrating piezoelectric transducers into aluminum die castings to generate smart lightweight structures

    Stefan Stein

    Full Text Available The application of piezoelectric transducers to structural body parts of machines or vehicles enables the combination of passive mechanical components with sensor and actuator functions in one single structure. According to Herold et al. [1] and Staeves [2] this approach indicates significant potential regarding smart lightweight construction. To obtain the highest yield, the piezoelectric transducers need to be integrated into the flux of forces (load path of load bearing structures. Application in a downstream process reduces yield and process efficiency during manufacturing and operation, due to the necessity of a subsequent process step of sensor/actuator application. The die casting process offers the possibility for integration of piezoelectric transducers into metal structures. Aluminum castings are particularly favorable due to their high quality and feasibility for high unit production at low cost (Brunhuber [3], Nogowizin [4]. Such molded aluminum parts with integrated piezoelectric transducers enable functions like active vibration damping, structural health monitoring or energy harvesting resulting in significant possibilities of weight reduction, which is an increasingly important driving force of automotive and aerospace industry (Klein [5], Siebenpfeiffer [6] due to increasingly stringent environmental protection laws. In the scope of those developments, this paper focuses on the entire process chain enabling the generation of lightweight metal structures with sensor and actuator function, starting from the manufacturing of piezoelectric modules over electrical and mechanical bonding to the integration of such modules into aluminum (Al matrices by die casting. To achieve this challenging goal, piezoceramic sensors/actuator modules, so-called LTCC/PZT modules (LPM were developed, since ceramic based piezoelectric modules are more likely to withstand the thermal stress of about 700 °C introduced by the casting process (Flössel et

  3. Fatigue Life Prediction in Rapid Die Casting - Preliminary Work in View of Current Research

    Chuan Huat Ng; Grote, Karl-Heinrich; Baehr, Ruediger

    2007-01-01

    Numerical simulation technique as a prediction tool is slowly adopted in metal casting industry for predicting design modelling solidification analysis. The reasons for this activity is found in the need to further enhance the geometrical design and mechanical properties of the tool design and the correct prediction methodology to fulfil industrial needs. The present state of numerical simulation capabilities in rapid die casting technologies is reviewed and the failure mode mechanisms of thermal fatigue, aimed at developing a numerical simulation with a systematic design guidance for predicting the thermal cyclic loading analysis and improvement is presented along with several other methods. The economic benefits of a numerical simulation technique in die casting are limited to tool life time, mechanical properties and design guidance. The extensive computer capabilities of a numerical simulation with a systematic design guidance methodology are exploited to provide a solution for flexible design, mechanical properties and mould life time. Related research carried out worldwide by different organisations and academic institutions are discussed

  4. Effect of parameters of high-pressure die casting on occurrence of casting nonconformities in sleeves of silumin alloy EN AB 47100

    Pałyga Ł.

    2017-03-01

    Full Text Available The paper presents a research on the effect of extreme - for the technology of the considered silumin EN AB 47100 - parameters of high-pressure die casting on occurrence of casting nonconformities. Considered was influence of the way of assembling the mould cooled-down to 140-160°C, non-standard for the selected casting, and pouring temperature in the range of 705 to 720°C (higher than the recommended of non-refined alloy. The castings were prepared with use of a high-pressure casting machine made by Kirov with mould closing force of 2500 kN. Occurrence of nonconformities was evaluated on properly prepared specimens taken from the castings manufactured with various parameters of the injection piston and various multiplication pressures. The results were subjected to quantitative and qualitative analyses of casting nonconformities and distribution of major alloying elements. It was found that proper selection of working parameters of the casting machine, in spite of disadvantageous pouring conditions, makes it possible to reduce occurrence of some casting defects, like shrinkage cavities and porosity, to improve tightness of castings even when the alloy refining process is omitted.

  5. Water mist effect on cooling range and efficiency of casting die

    R. Władysiak

    2008-12-01

    Full Text Available This project is showing investigation results of cooling process of casting die in the temperature range 570÷100 °C with 0.40 MPa compressed air and water mist streamed under pressure 0.25÷0.45 MPa in air jet 0.25÷0.50 MPa using open cooling system.The character and the speed of changes of temperature, forming of the temperture’s gradient along parallel layer to cooled surface of die is shawing with thermal and derivative curves. The effect of kind of cooling factor on the temperature and time and distance from cooling nozzle is presented in the paper. A designed device for generating the water mist cooling the die and the view of sprying water stream is shown here. It’s proved that using of the water mist together with the change of heat transfer interface increases intensity of cooling in the zone and makes less the range cooling zone and reduces the porosity of cast microstructure.

  6. Determining the optimal index of heat stress in foundry, die casting and road construction industries using FAHP_Topsis

    Maryam Dehghanipoor

    2016-12-01

    Full Text Available Introduction: Heat stress is one of the harmful risks in casting and die casting industries, which can not only cause work-related diseases but also can impair the performance and safety of workers. Since the indicators that are used to evaluate heat stress are very different, it is very difficult to choose a suitable index. The aim of this study was to determine the optimum heat stress index in foundry, die-cast, and road construction industries using FAHP and Topsis methods. Material and Method: In order to determine optimum heat stress index in foundry, die-cast, and road construction industries, first, the prioritization criteria were defined by experts (including ease of measurement, measurement accuracy, comprehensiveness, time, cost, and correlation. Then, considering these criteria, the best heat stress index was determined based on experts’ opinions and using FAHP and Topsis methods. Result: The results of this study suggest that given the current conditions and criteria, WBGT and P4SR is the best indices for foundry, die casting and construction. Conclusion: The results showed that according to comprehensiveness, accuracy and correlation criteria, the WBGT index is considered as the best indicator of heat stress assessment in foundry, die-cast and road construction industries. Moreover, the HSI ranked in the last place due to the complexity and cost of its calculation.

  7. Microstructure and Properties of Cobalt-and Zinc-Containing Magnetic Magnesium Alloys Processed by High-Pressure Die Casting

    Klose, Christian; Demminger, Christian; Maier, Hans Jürgen

    The inherent magnetic properties of lightweight alloys based on magnesium and cobalt offer a novel way in order to measure mechanical loads throughout the entire structural component using the magnetoelastic effect. Because the solubility of cobalt in the magnesium matrix is negligible, the magnetic properties mainly originate from Co-rich precipitates. Thus, the size and distribution of Co-containing phases within the alloy's microstructure wields a major influence on the amplitude of the load-sensitive properties which can be measured by employing the harmonic analysis of eddy-current signals. In this study, Mg-Co-based alloys are produced by several casting methods which allow the application of different cooling rates, e.g. gravity die casting and high-pressure die casting. The differences between the manufactured alloys' micro- and phase structures are compared depending on the applied cooling rate and the superior magnetic and mechanical properties of the high-pressure die cast material are demonstrated.

  8. Technical-economic modelling of an aluminium high pressure die casting system for automotive parts fabrication

    Faura, F.

    1997-01-01

    In the present paper a technical-economic model for an aluminium high pressure die casting system has been developed. In order to obtain the necessary data for correlations utilized by the model, has been analyzed the production systems of companies that use these processes. This has allowed to determine the most important technological variables that affect to the economical aspect of the process. A computer application has been developed which allows to explore easily the influence of different system parameters. (Author) 12 refs

  9. Cast Metals Coalition Technology Transfer and Program Management Final Report

    Gwyn, Mike

    2009-03-31

    The Cast Metals Coalition (CMC) partnership program was funded to ensure that the results of the Department of Energy's (DOE) metalcasting research and development (R&D) projects are successfully deployed into industry. Specifically, the CMC program coordinated the transfer and deployment of energy saving technologies and process improvements developed under separately funded DOE programs and projects into industry. The transition of these technologies and process improvements is a critical step in the path to realizing actual energy savings. At full deployment, DOE funded metalcasting R&D results are projected to save 55% of the energy used by the industry in 1998. This closely aligns with DOE's current goal of driving a 25% reduction in industrial energy intensity by 2017. In addition to benefiting DOE, these energy savings provide metalcasters with a significant economic advantage. Deployment of already completed R&D project results and those still underway is estimated to return over 500% of the original DOE and industry investment. Energy savings estimates through December 2008 from the Energy-Saving Melting and Revert Reduction Technology (E-SMARRT) portfolio of projects alone are 12 x 1012 BTUs, with a projection of over 50 x 1012 BTUs ten years after program completion. These energy savings and process improvements have been made possible through the unique collaborative structure of the CMC partnership. The CMC team consists of DOE's Office of Industrial Technology, the three leading metalcasting technical societies in the U.S: the American Foundry Society; the North American Die Casting Association; and the Steel Founders Society of America; and the Advanced Technology Institute (ATI), a recognized leader in distributed technology management. CMC provides collaborative leadership to a complex industry composed of approximately 2,100 companies, 80% of which employ less than 100 people, and only 4% of which employ more than 250 people

  10. Annealing of chromium oxycarbide coatings deposited by plasma immersion ion processing (PIIP) for aluminum die casting

    Peters, A.M.; He, X.M.; Trkula, M.; Nastasi, M.

    2001-01-01

    Chromium oxycarbide coatings have been investigated for use as non-wetting coatings for aluminum die casting. This paper examines Cr-C-O coating stability and non-wetability at elevated temperatures for extended periods. Coatings were deposited onto 304 stainless steel from chromium carbonyl [Cr(CO) 6 ] by plasma immersion ion processing. The coatings were annealed in air at an aluminum die casting temperature of 700 deg. C up to 8 h. Coatings were analyzed using resonant ion backscattering spectroscopy, nanoindentation and pin-on-disk tribometry. Molten aluminum was used to determine coating wetting and contact angle. Results indicate that the surface oxide layer reaches a maximum thickness of 900 nm. Oxygen concentrations in the coatings increased from 24% to 34%, while the surface concentration rose to almost 45%. Hardness values ranged from 22.1 to 6.7 GPa, wear coefficients ranged from 21 to 8x10 -6 mm 3 /Nm and contact angles ranged from 156 deg. to 127 deg

  11. A process chain for integrating piezoelectric transducers into aluminum die castings to generate smart lightweight structures

    Stein, Stefan; Wedler, Jonathan; Rhein, Sebastian; Schmidt, Michael; Körner, Carolin; Michaelis, Alexander; Gebhardt, Sylvia

    The application of piezoelectric transducers to structural body parts of machines or vehicles enables the combination of passive mechanical components with sensor and actuator functions in one single structure. According to Herold et al. [1] and Staeves [2] this approach indicates significant potential regarding smart lightweight construction. To obtain the highest yield, the piezoelectric transducers need to be integrated into the flux of forces (load path) of load bearing structures. Application in a downstream process reduces yield and process efficiency during manufacturing and operation, due to the necessity of a subsequent process step of sensor/actuator application. The die casting process offers the possibility for integration of piezoelectric transducers into metal structures. Aluminum castings are particularly favorable due to their high quality and feasibility for high unit production at low cost (Brunhuber [3], Nogowizin [4]). Such molded aluminum parts with integrated piezoelectric transducers enable functions like active vibration damping, structural health monitoring or energy harvesting resulting in significant possibilities of weight reduction, which is an increasingly important driving force of automotive and aerospace industry (Klein [5], Siebenpfeiffer [6]) due to increasingly stringent environmental protection laws. In the scope of those developments, this paper focuses on the entire process chain enabling the generation of lightweight metal structures with sensor and actuator function, starting from the manufacturing of piezoelectric modules over electrical and mechanical bonding to the integration of such modules into aluminum (Al) matrices by die casting. To achieve this challenging goal, piezoceramic sensors/actuator modules, so-called LTCC/PZT modules (LPM) were developed, since ceramic based piezoelectric modules are more likely to withstand the thermal stress of about 700 °C introduced by the casting process (Flössel et al., [7]). The

  12. A new approach to assess the effects of Sr and Bi interaction in ADC12 Al–Si die casting alloy

    Farahany, Saeed, E-mail: saeedfarahany@gmail.com; Ourdjini, Ali; Abu Bakar, Tuty Asma; Idris, Mohd Hasbullah

    2014-01-10

    Highlights: • Interactive effect between Bi and Sr has been invesitigated comprehensively. • Sequence of addition did not affect thermal and microscopical characteristics. • A new map has been established to assess the final microstructure of castings. - Abstract: In the present paper, the possible interaction between bismuth and strontium in ADC12 die casting alloy was investigated comprehensively by using in situ thermal analysis technique. The characteristic temperatures including nucleation, minimum and growth temperatures of eutectic Al–Si were also analyzed. The results show that with Bi present in the Al–Si alloy melt the efficiency of Sr in modifying the eutectic Si is reduced. A threshold Sr/Bi ratio of at least 0.5 is required for a fully modified Si structure to form. A new map based on the characteristic temperatures, Sr/Bi ratio and microstructure, was established to assess the microstructure of fully solidified Al–Si castings.

  13. A new approach to assess the effects of Sr and Bi interaction in ADC12 Al–Si die casting alloy

    Farahany, Saeed; Ourdjini, Ali; Abu Bakar, Tuty Asma; Idris, Mohd Hasbullah

    2014-01-01

    Highlights: • Interactive effect between Bi and Sr has been invesitigated comprehensively. • Sequence of addition did not affect thermal and microscopical characteristics. • A new map has been established to assess the final microstructure of castings. - Abstract: In the present paper, the possible interaction between bismuth and strontium in ADC12 die casting alloy was investigated comprehensively by using in situ thermal analysis technique. The characteristic temperatures including nucleation, minimum and growth temperatures of eutectic Al–Si were also analyzed. The results show that with Bi present in the Al–Si alloy melt the efficiency of Sr in modifying the eutectic Si is reduced. A threshold Sr/Bi ratio of at least 0.5 is required for a fully modified Si structure to form. A new map based on the characteristic temperatures, Sr/Bi ratio and microstructure, was established to assess the microstructure of fully solidified Al–Si castings

  14. Improved design and durability of aluminum die casting horizontal shot sleeves

    Birceanu, Sebastian

    The design and performance of shot sleeves is critical in meeting the engineering requirements of aluminum die cast parts. Improvement in shot sleeve materials have a major impact on dimensional stability, reproducibility and quality of the product. This investigation was undertaken in order to improve the life of aluminum die casting horizontal shot sleeves. Preliminary pin tests were run to evaluate the soldering, wash-out and thermal fatigue behavior of commercially available materials and coatings. An experimental rig was designed and constructed for shot sleeve configuration evaluation. Fabrication and testing of experimental shot sleeves was based upon preliminary results and manufacturing costs. Three shot sleeve designs and materials were compared to a reference nitrided H13 sleeve. Nitrided H13 is the preferred material for aluminum die casting shot sleeves because of wear resistance, strength and relative good soldering and wash-out resistance. The study was directed towards damage evaluation on the area under the pouring hole. This area is the most susceptible to damage because of high temperatures and impingement of molten aluminum. The results of this study showed that tungsten and molybdenum had the least amount of soldering and wash-out damage, and the best thermal fatigue resistance. Low solubility in molten aluminum and stability of intermetallic layers are main factors that determine the soldering and wash-out behavior. Thermal conductivity and thermal expansion coefficient directly influence thermal fatigue behavior. TiAlN nanolayered coating was chosen as the material with the best damage resistance among several commercial PVD coatings, because of relatively large thickness and simple deposition conditions. The results show that molybdenum thermal sprayed coating provided the best protection against damage under the pouring hole. Improved bonding is however required for life extension of the coating. TiAlN PVD coating applied on H13 nitrided

  15. Case study of lean manufacturing application in a die casting manufacturing company

    Ching, Ng Tan; Hoe, Clarence Chan Kok; Hong, Tang Sai; Ghobakhloo, Morteza; Pin, Chen Kah

    2015-05-01

    The case study of lean manufacturing aims to study the application of lean manufacturing in a die casting manufacturing company located in Pulau Penang, Malaysia. This case study describes mainly about the important concepts and applications of lean manufacturing which could gradually help the company in increasing the profit by studying and analyzing their current manufacturing process and company culture. Many approaches of lean manufacturing are studied in this project which includes: 5S housekeeping, Kaizen, and Takt Time. Besides, the lean tools mentioned, quality tool such as the House of Quality is being used as an analysis tool to continuously improve the product quality. In short, the existing lean culture in the company is studied and analyzed, with recommendations written at the end of this paper.

  16. A Study on Development of High Strength Al-Zn Based alloy for Die Casting

    Shin, Sang-Soo; Park, Ik-Min [Pusan National University, Busan (Korea, Republic of); Yeom, Gil-Young; Lim, Kyoung-Mook [Korea Institute of Industrial Technology, Incheon (Korea, Republic of); Son, Hyun-Jin [Oh-Sung Co. Ltd., Siheung (Korea, Republic of)

    2015-09-15

    In this study, the microstructural evolution and various characteristics of Al-20⁓45wt%Zn alloys were investigated. In terms of microstructure, as the amount of Zn addition to the alloys increased, the α-phase size decreased and the α+η non-equilibrium solidification phase fraction increased. Also, increasing Zn content improved the wear resistance of the alloys, but reduced the damping capacity and toughness of the alloys. Their physical properties of the Al-Zn alloy with high Zn content, specifically the wear resistance and toughness, were superior to those of commercial ALDC12 alloys for die-casting. Based on these results, we considered the possibility of application of the developed Al-Zn alloy as a structural material.

  17. Evaluations of antimony and strontium interaction in an Al–Si–Cu–Zn die cast alloy

    Farahany, Saeed, E-mail: saeedfarahany@gmail.com; Idris, Mohd Hasbullah; Ourdjini, Ali

    2014-05-01

    Graphical abstract: - Highlights: • Probable interactions between Sb and Sr in a complex Al–Si alloy were evaluated. • Sequence of addition did not affect thermal and microscopical characteristics. • Threshold ratio for the Sb and Sr interaction is proposed. - Abstract: The interaction between antimony and strontium in an ADC12 die casting alloy is investigated comprehensively by using a computer aided cooling curve thermal analysis coupled with microstructure inspection. The results of the thermal analysis show significant changes in Al–Si eutectic reaction based on different concentrations of Sb and Sr. Sb reduces the efficiency of Sr in modifying the eutectic Si. Based upon the data obtained in this study, the threshold Sr/Sb ratio should exceed about 0.5 in order to obtain fully modified structure. Moreover, a pre-eutectic reaction of Al{sub 2}Si{sub 2}Sr intermetallic was detected for high concentrations of Sr.

  18. A Study on Development of High Strength Al-Zn Based alloy for Die Casting

    Shin, Sang-Soo; Park, Ik-Min; Yeom, Gil-Young; Lim, Kyoung-Mook; Son, Hyun-Jin

    2015-01-01

    In this study, the microstructural evolution and various characteristics of Al-20⁓45wt%Zn alloys were investigated. In terms of microstructure, as the amount of Zn addition to the alloys increased, the α-phase size decreased and the α+η non-equilibrium solidification phase fraction increased. Also, increasing Zn content improved the wear resistance of the alloys, but reduced the damping capacity and toughness of the alloys. Their physical properties of the Al-Zn alloy with high Zn content, specifically the wear resistance and toughness, were superior to those of commercial ALDC12 alloys for die-casting. Based on these results, we considered the possibility of application of the developed Al-Zn alloy as a structural material.

  19. Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Development of Surface Engineered Coating Systems for Aluminum Pressure Die Casting Dies: Towards a 'Smart' Die Coating

    Dr. John J. Moore; Dr. Jianliang Lin,

    2012-07-31

    The main objective of this research program was to design and develop an optimal coating system that extends die life by minimizing premature die failure. In high-pressure aluminum die-casting, the die, core pins and inserts must withstand severe processing conditions. Many of the dies and tools in the industry are being coated to improve wear-resistance and decrease down-time for maintenance. However, thermal fatigue in metal itself can still be a major problem, especially since it often leads to catastrophic failure (i.e. die breakage) as opposed to a wear-based failure (parts begin to go out of tolerance). Tooling costs remain the largest portion of production costs for many of these parts, so the ability prevent catastrophic failures would be transformative for the manufacturing industry.The technology offers energy savings through reduced energy use in the die casting process from several factors, including increased life of the tools and dies, reuse of the dies and die components, reduction/elimination of lubricants, and reduced machine down time, and reduction of Al solder sticking on the die. The use of the optimized die coating system will also reduce environmental wastes and scrap parts. Current (2012) annual energy saving estimates, based on initial dissemination to the casting industry in 2010 and market penetration of 80% by 2020, is 3.1 trillion BTU's/year. The average annual estimate of CO2 reduction per year through 2020 is 0.63 Million Metric Tons of Carbon Equivalent (MM TCE).

  20. The ‘full sleeve’ application in the horizontal cold-chamber machine for pressure die casting of aluminium alloys

    Z. Konopka

    2008-04-01

    Full Text Available The ‘full sleeve’ construction has been designed and accomplished in the horizontal cold-chamber pressure die casting machine. Main part of this solution is a counter plunger placed in a movable die half which allows for full filling of the shot sleeve and precisely fixes the metal quantity needed for casting. The purpose of this new construction solution is mainly the reduction of the casting porosity caused by air entrapment and the improvement of both castability and accuracy of the die cavity reproduction. For such a redesigned machine there have been performed examinations consisting in pressure casting of AlSi9Cu alloy (EN AC-46000 at varying plunger velocity in the second stage of injection and varying intensification pressure. The alloy castability (the die filling ability has been measured for each parameter setting. For the purpose of comparison, similar measurements have been performed also for the conventional system without a counter plunger. The castability examination has been done by means of a specially designed die with an impression of a trial casting of variable wall thickness. The experiments have been held according to the assumed factor design 22, what allowed for determining the mathematical models describing the influence of die filling parameters on the castability and the die cavity reproduction level. Both alternatives of the experiment confirmed the positive influence of plunger velocity and intensification pressure increase on the improvement of castability, the measure of the latter being the filled length of the impression. Applying of the new ‘full sleeve’ solution has improved castability for each experiment by about 20% as compared with conventional alternative. Castability in the ‘full sleeve’ system has been increased even for low values of plunger velocity and intensification pressure. For both alternative systems the influence of plunger velocity has been found, as an average, by four times

  1. Comparative study on laser welding and TIG welding of semi-solid high pressure die cast A356 aluminium alloy

    Govender, G

    2007-07-01

    Full Text Available components. The low porosity levels in SSM high pressure die castings (HPDC) improves the weldability of these components. The aim of the current research was to perform a comparative study of laser and TIG welding of SSM HPDC aluminium alloy A356. SSM...

  2. Microstructure investigation and first-principle analysis of die-cast AZ91 alloy with calcium addition

    Lin, L.; Wang, F.; Yang, L.; Chen, L.J.; Liu, Z.; Wang, Y.M.

    2011-01-01

    Highlights: → Die-cast AZ91 with Ca addition was investigated experimentally and theoretically. → Precipitation sequence was confirmed with increasing Ca addition. → Phase stability difference was verified by first-principle calculation. → Valence configurations were associated with alloying effects of Al, Mg and Ca. - Abstract: In order to get improved mechanical properties of die-cast AZ91 alloy under elevated temperatures, Ca element was added as a cost-effective alloying constituent. It appeared that minor Ca addition less than 0.5 wt% would result in no apparent change in microstructure, but the tensile strength at elevated temperatures was improved considerably. When increasing Ca addition to more than 1.0 wt%, Al 2 Ca phase will precipitate during solidification, no Mg 2 Ca phase was discovered. Homogeneous microstructure and high temperature stability in tensile strength of die-cast AZ91 alloy with Ca addition was mainly attributed to the precipitation of Al 2 Ca phase, which considerably refined the bulky β-Mg 17 Al 12 phase distributed originally at the grain boundaries of die-cast AZ91 alloy with no Ca addition. The priority of Al 2 Ca phase compared to Mg 2 Ca phase in precipitation sequence was verified by first-principle calculation of their cohesive energy and formation enthalpy, and can also be associated with more bounding electrons between Al and Ca atoms.

  3. Casting dimensional control and fatigue life prediction for permanent mold casting dies. Technical progress report, September 29, 1993-- September 30, 1994

    NONE

    1994-11-01

    First year efforts as part of a three year program to address metal casting dimensional control and fatigue life prediction for permanent mold casting dies are described. Procedures have been developed and implemented to collect dimensional variability data from production steel castings. The influence of process variation and casting geometry variables on dimensional tolerances have been investigated. Preliminary results have shown that these factors have a significant influence on dimensional variability, although this variability is considerably less than the variability indicated in current tolerance standards. Gage repeatability and reproducibility testing must precede dimensional studies to insure that measurement system errors are acceptably small. Also initial efforts leading to the development and validation of a CAD/CAE model to predict the thermal fatigue life of permanent molds for aluminum castings are described. An appropriate thermomechanical property database for metal, mold and coating materials has been constructed. A finite element model has been developed to simulate the mold temperature distribution during repeated casting cycles. Initial validation trials have indicated the validity of the temperature distribution model developed.

  4. The Influence of Pressure Die Casting Parameters on the Castability of AlSi11-SiCp Composites

    Konopka Z.

    2015-03-01

    Full Text Available The paper presents the method of preparing a composite slurry composed of AlSi11 alloy matrix and 10 vol.% of SiC particles, as well as the method of its high-pressure die casting and the measurement results concerning the castability of the obtained composite. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. There were found the regression equations describing the change of castability of the examined composite as a function of pressure die casting process parameters. The conclusion gives the analysis and the interpretation of the obtained results.

  5. Interlocking multi-material components made of structured steel sheets and high-pressure die cast aluminium

    Senge, S.; Brachmann, J.; Hirt, G.; Bührig-Polaczek, A.

    2017-10-01

    Lightweight design is a major driving force of innovation, especially in the automotive industry. Using hybrid components made of two or more different materials is one approach to reduce the vehicles weight and decrease fuel consumption. As a possible way to increase the stiffness of multi-material components, this paper presents a process chain to produce such components made of steel sheets and high-pressure die cast aluminium. Prior to the casting sequence the steel sheets are structured in a modified rolling process which enables continuous interlocking with the aluminium. Two structures manufactured by this rolling process are tested. The first one is a channel like structure and the second one is a channel like structure with undercuts. These undercuts enable the formation of small anchors when the molten aluminium fills them. The correlation between thickness reduction during rolling and the shape of the resulting structure was evaluated for both structures. It can be stated that channels with a depth of up to 0.5 mm and a width of 1 mm could be created. Undercuts with different size depending on the thickness reduction could be realised. Subsequent aluminium high-pressure die casting experiments were performed to determine if the surface structure can be filled gap-free with molten aluminium during the casting sequence and if a gap-free connection can be achieved after contraction of the aluminium. The casting experiments showed that both structures could be filled during the high-pressure die casting. The channel like structure results in a gap between steel and aluminium after contraction of the cast metal whereas the structure with undercuts leads to a good interlocking resulting in a gap-free connection.

  6. Comparative study on microstructures and mechanical properties of the heat-treated Al–5.0Cu–0.6Mn–xFe alloys prepared by gravity die casting and squeeze casting

    Lin, Bo; Zhang, WeiWen; Lou, ZhaoHui; Zhang, DaTong; Li, YuanYuan

    2014-01-01

    Highlights: • Only two kind Fe-rich intermetallics are found in the heat-treated Al–5.0Cu–0.6Mn–xFe alloys. • Squeeze cast Al–5.0Cu–0.6Mn alloys containing 1.5% Fe have desirable mechanical properties. • The difference between gravity die cast and squeeze cast Al–5.0Cu–0.6Mn–xFe alloys. - Abstract: The Al–5.0 wt% Cu–0.6 wt% Mn alloys with different Fe contents were prepared by gravity die casting and squeeze casting. The difference in microstructures and mechanical properties of the T5 heat-treated alloys was examined by tensile test, optical microscopy, deep etching technique, scanning electron microscope and electron probe micro-analyzer. The results show that both β-Fe and α (CuFe) are observed in T5 heat-treated gravity die cast alloy and only α (CuFe) appears in the squeeze cast alloy when the Fe content is 0.5 wt%. When the Fe content is more than 1.0 wt%, the main Fe-rich intermetallics is α (CuFe) in both squeeze cast and gravity die cast alloys. The mechanical properties of both the gravity die cast and squeeze cast alloys decrease gradually with the increase of Fe content due to the decreased volume fraction of precipitation particles, the increased volume fraction of Fe-rich intermetallics and the increased size of α (Al) dendrites. The squeeze cast alloys with different Fe contents have superior mechanical properties compared to the gravity die cast alloys, which is mainly attributed to the reduction of porosity and refinement of Fe-rich intermetallics and α (Al) dendrite. In particularly, the elongation of the squeeze cast alloys is less sensitive to the Fe content than that of the gravity die cast alloys. An elongation level of 13.7% is obtained in squeeze cast alloy even when the Fe content is as high as 1.5%, while that of the gravity die cast alloy is only 5.3%

  7. Analysis of the creep behaviour of die-cast Mg–3Al–1Si alloy

    Zhu, S.M.; Easton, M.A.; Gibson, M.A.; Dargusch, M.S.; Nie, J.F.

    2013-01-01

    The creep behaviour of die-cast Mg–3Al–1Si (AS31) alloy has been studied at 125 °C, 150 °C and 175 °C with stresses ranging 50–110 MPa. The alloy exhibits anomalously high stress exponents, i.e. 14.4 at 125 °C, 11.6 at 150 °C and 9.5 at 175 °C. Contrary to work reported previously, these high stress exponents cannot be rationalised using the threshold stress approach that is commonly adopted in analysing creep behaviour of dispersion strengthened alloys or metal matrix composites. It is shown that the observed high stress exponents are associated with the dominance of power-law breakdown creep in this study, and the stress dependence can be well described by the Garofalo sinh relationship with the natural exponent of 5. Transmission electron microscopy (TEM) observations reveal that cross-slip of 〈a〉 type dislocations is probably the controlling creep mechanism

  8. New high pressure die cast magnesium alloy AM-HP2 for powertrain applications

    Gibson, M.A. [Queensland Univ., Brisbane (Australia). CAST CRC]|[CSIRO Manufacturing and Materials Technology, Clayton (Australia); Zhu, S.M.; Nie, J.F. [Queensland Univ., Brisbane (Australia). CAST CRC]|[Monash Univ., Monash (Australia). Dept. of Materials Engineering

    2007-07-01

    In order to improve the benefits available through weight savings on engine emissions, magnesium alloys must gain wider acceptance in transmission and engine applications. This paper provided details of a new alloy with exceptional creep properties developed for automotive powertrain applications. The AM-HP2 alloy was developed as part of a broader research program investigating the relationship between the composition, structure and properties of magnesium rare earth (Mg-RE) based alloys and high-pressure die casting (HPDC). Cylindrical test specimens of various alloys were produced on a cold chamber HPDC machine. Tensile creep tests were then conducted under a constant load at 177 degrees C for a period of 600 hours. Microstructures of specimens were characterized using a CM20 transmission electron microscope. Results of the tests indicated that near-grain boundary microstructure was an important parameter in securing optimum elevated temperature properties. The RE element had a significant effect on the creep behaviour of the HPDC Mg-RE alloys. It was concluded that further research is needed to investigate the influence of the RE mixture in improving creep performance. 15 refs., 2 tabs., 6 figs.

  9. Analysis of the creep behaviour of die-cast Mg–3Al–1Si alloy

    Zhu, S.M., E-mail: suming.zhu@monash.edu [CAST Cooperative Research Centre, Department of Materials Engineering, Monash University, Victoria 3800 (Australia); ARC Centre of Excellence for Design in Light Metals, Department of Materials Engineering, Monash University, Victoria 3800 (Australia); Easton, M.A. [CAST Cooperative Research Centre, Department of Materials Engineering, Monash University, Victoria 3800 (Australia); Gibson, M.A. [CAST Cooperative Research Centre, CSIRO Process Science and Engineering, Clayton, Victoria 3169 (Australia); Dargusch, M.S. [Centre for Advanced Materials Processing and Manufacturing, School of Mechanical and Mining Engineering, The University of Queensland, Queensland 4075 (Australia); Defence Materials Technology Centre, The University of Queensland, Queensland 4075 (Australia); Nie, J.F. [ARC Centre of Excellence for Design in Light Metals, Department of Materials Engineering, Monash University, Victoria 3800 (Australia)

    2013-08-20

    The creep behaviour of die-cast Mg–3Al–1Si (AS31) alloy has been studied at 125 °C, 150 °C and 175 °C with stresses ranging 50–110 MPa. The alloy exhibits anomalously high stress exponents, i.e. 14.4 at 125 °C, 11.6 at 150 °C and 9.5 at 175 °C. Contrary to work reported previously, these high stress exponents cannot be rationalised using the threshold stress approach that is commonly adopted in analysing creep behaviour of dispersion strengthened alloys or metal matrix composites. It is shown that the observed high stress exponents are associated with the dominance of power-law breakdown creep in this study, and the stress dependence can be well described by the Garofalo sinh relationship with the natural exponent of 5. Transmission electron microscopy (TEM) observations reveal that cross-slip of 〈a〉 type dislocations is probably the controlling creep mechanism.

  10. Microstructural effects of phosphorus on pressure die cast Al-12Si components

    Suárez-Peña, B.

    2007-10-01

    Full Text Available The refinement of cuboidal silicon in eutectic Al-Si alloys by phosphorus additions used to manufacture pressure die cast components was studied. The results show that the addition of phosphorus in the form of AlFeP mother alloy before process degassing, leads to the best refinement of the size of the Si-cuboids phase, among several phosphorus additions analysed in the present research.

    Se ha estudiado el afino del silicio cuboidal en aleaciones eutécticas Al-Si por acción del fósforo, en piezas obtenidas mediante la técnica de fundición a presión. Tras la adición de fósforo en pruebas industriales, en las que dicho elemento se incorpora al baño con diversas composiciones, los mejores resultados se obtienen con la adición de la aleación madre AlFeP, previa al desgasificado industrial.

  11. Microstructure and mechanical properties of AM50 alloy according to thickness and forming condition of the products by a high pressure die-casting process

    Park, Joon Hong [Dong-A University, Busan (Korea, Republic of); Kang, Chung Gil [Pusan National University, Busan (Korea, Republic of)

    2013-10-15

    In recent years, Magnesium (Mg) and its alloys have become a center of special interest in the automotive industry. Due to their high specific mechanical properties, they offer a significant weight saving potential in modern vehicle constructions. Most Mg alloys show very good machinability and processability, and even the most complicated die casting parts can be easily produced. The die casting process is a fast production method capable of a high degree of automation for which certain Mg alloys are ideally suited. Although Mg alloys are fulfilling the demands for low specific weight materials with excellent machining and casting abilities, they are still not used in die casting process to the same extent as the competing material aluminum. One of the reasons is that effects of various forming variables for die casting process is not closely examined from the viewpoint of die design. In this study, step die and flowability tests for AM50 were performed by die casting process according to various combination of casting pressure and plunger velocity. Microstructure, Vickers hardness and tensile tests were examined and performed for each specimen to verify effects of forming conditions.

  12. Improved Life of Die Casting Dies of H13 Steel by Attaining Improved Mechanical Properties and Distortion Control During Heat Treatment

    J. F. Wallace; D. Schwam

    1998-10-01

    The ultimate goal of this project is to increase die casting die life by using fast enough quenching rates to obtain good toughness and fatigue resistance in premium grade H-13 steel dies. The main tasks of the project were to compile a database on physical and mechanical properties of H-13; conduct gas quenching experiments to determine cooling rates of dies in difference vacuum furnaces; measure the as-quenched distortion of dies and the residual stresses; generate finite element analysis models to predict cooling rates, distortion, and residual stress of gas quenched dies; and establish rules and create PC-based expert system for prediction of cooling rates, distortion, and residual stress in vacuum/gas quenched H-13 dies. Cooling curves during gas quenching of H-13 blocks and die shapes have been measured under a variety of gas pressure. Dimensional changes caused by the gas quenching processes have been determined by accurate mapping of all surfaces with coordinate measuring machines before and after the quench. Residual stresses were determined by the ASTM E837 hole-drilling strain gage method. To facilitate the computer modeling work, a comprehensive database of H-13 mechanical and physical properties has been compiled. Finite element analysis of the heat treated shapes has been conducted using the TRAST/ABAQUS codes. There is a good fit between the predicted and measured distortion contours. However, the magnitude of the predicted distortion and residual stresses does not match well the measured values. Further fine tuning of the model is required before it can be used to predict distortion and residual stress in a quantitative manner. This last step is a prerequisite to generating rules for a reliable expert system.

  13. An establish attempt of reasons of machining splinter formation in AC44200 alloy high pressure die castings

    J. Mutwil

    2008-10-01

    Full Text Available A problem of splinter formation during machining the AC44200 alloy high pressure die casting has been experimental investigated. Inorder to establish the reason of this occurrence a set of 200 high pressure die casting of the tensile strength samples have been prepared. The tensile tests were carried out using a Zwick Z050 universal testing machine. JM-SPC program has been used for statistical analysis of test results. A large variability of tensile strength results has been found. In order to find the reason of this variability the fracture surface investigations (macrographs for all of samples and SEM micrographs for chosen samples have been carried out. It has been establish that in all cases a significant decrease of tensile strength was caused by presence of inclusions or porosity. In lot of cases the inclusions have a form of oxide film.

  14. Ejection Performance of Coated Core Pins Intended for Application on High Pressure Die Casting Tools for Aluminium Alloys Processing

    P. Terek

    2017-09-01

    Full Text Available In high pressure die casting (HPDC process of aluminium alloys cast alloy soldering severely damages tool surfaces. It hampers casting ejection, reduces the casting quality and decreases the overall production efficiency. Thin ceramic PVD (physical vapor deposition coatings applied on tool surfaces successfully reduce these effects. However, their performance is still not recognised for surfaces with various topographies. In this investigation, soldering tendency of Al-Si-Cu alloy toward EN X27CrMoV51 steel, plasma nitrided steel, CrN and TiAlN duplex PVD coatings is evaluated using ejection test. The coatings were prepared to a range of surface roughness and topographies. After the tests sample surfaces were analysed by different microscopy techniques and profilometry. It was found that the ejection performance is independent of the chemical composition of investigated materials. After the ejection, the cast alloy soldering layer was found on surfaces of all tested materials. This built-up layer formed by effects of mechanical soldering, without corrosion reactions. Coated samples displayed a pronounced dependence of ejection force on surface roughness and topography. By decreasing roughness, ejection force increased, which is a consequence of intensified adhesion effects. Presented findings are a novel information important for efficient application of PVD coatings intendent for protection of HPDC tools.

  15. An eco design strategy for high pressure die casting components: microstructural analysis applied to mass reducing processes

    Suarez-Pena, B.; Asensio-Lozano, J.

    2009-01-01

    In this work the study focused on the possibility of use of new aluminium alloys with optimized microstructures that ensure the mechanical properties requested for cast components made by high pressure die casting. The objective was to check the possibility of manufacture of structurally sound eco-steps for escalators with reduced structural integrity. The former arises as a result of a new redesign of the traditional steps aiming at a significant weight reduction. The experimental results show that it is feasible to cut the use of materials during processing and therefore to reduce the impact of the components during its lifetime, whilst the performance and safety standards are kept identical or even improved. (Author) 17 refs

  16. The correlation between microstructure and mechanical properties of high-pressure die-cast AM50 alloy

    Song Jie; Xiong Shoumei; Li Mei; Allison, John

    2009-01-01

    Scanning acoustic microscopy was used to characterize the micro-voids distribution for specimens in non-destructive mode. In addition, the in-situ scanning electron microscopy observation was performed during tensile deformation of high-pressure die-cast (HPDC) of AM50 alloy to obtain the mechanism of fracture induced by micro-voids. The effects of micro-voids on the mechanical properties were discussed. The results obtained from the examination suggest that fracture tends to occur at bigger micro-voids or in the cluster micro-voids area.

  17. Theoretic and Experimental Studies on the Casting of Large Die-Type Parts Made of Lamellar Graphite Grey Pig Irons by Using the Technology of Polystyrene Moulds Casting from Two Sprue Cups

    Constantin Marta

    2012-01-01

    Full Text Available This paper presents a comparative analysis between the practical results of pig iron die-type part casting and the results reached by simulation. The insert was made of polystyrene, and the casting was downward vertical. As after the part casting and heat treatment cracks were observed in the part, it became necessary to locate and identify these fissures and to establish some measures for eliminating the casting defects and for locating them. The research method was the comparisons of defects identified through verifications, measurements, and metallographic analyses applied to the cast part with the results of some criteria specific to simulation after simulating the casting process. In order to verify the compatibility between reality and simulation, we then simulated the part casting respecting the real conditions in which it was cast. By visualising certain sections of the cast part during solidification, relevant details occur about the possible evolution of defects. The simulation software was AnyCasting, the measurements were done through nondestructive methods.

  18. Experiments on the Model Testing of the 2nd Phase of Die Casting Process Compared with the Results of Numerical Simulation

    Dańko R.

    2015-12-01

    Full Text Available Experiments of filling the model moulds cavity of various inner shapes inserted in rectangular cavity of the casting die (dimensions: 280 mm (height × 190 mm (width × 10 mm (depth by applying model liquids of various density and viscosity are presented in the paper. Influence of die venting as well as inlet system area and inlet velocity on the volumetric rate of filling of the model liquid - achieved by means of filming the process in the system of a cold-chamber casting die was tested. Experiments compared with the results of simulation performed by means of the calculation module Novacast (Novaflow&Solid for the selected various casting conditions - are also presented in the paper.

  19. Die-cast of a hypo-eutectic AL-SI alloy: influence of injection temperature on microstructure and mechanical properties

    Santos, Silvano Leal dos; Santos, Sydney Ferreira

    2014-01-01

    Die-casting is widely used for manufacturing light alloy components for automotive industry. Among others, hypo-eutectic Al-Si alloys are currently processed by die-casting. To obtain high quality die-cast components, a better understanding on the correlations between processing parameters, microstructures, and mechanical properties are of utmost importance. In this study, we investigate the effect of injection temperature of liquid metal on the microstructure and mechanical properties of Al-Si alloy EN AC 46000 (DIN designation). The injection temperatures were 579, 589, 643, and 709 deg C. As-cast components had their microstructures analyzed by X-ray diffraction, optical and scanning electron microscopy, and X-ray energy dispersive spectroscopy. The mechanical properties were examined by micro-hardness and tensile tests. It was observed that the ultimate tensile strength slightly increased with the increase of injection temperature. The same trend was observed for micro-hardness. The amount of porosity in the samples varies in a small amount for different injection temperatures. On the other hand, the microstructure of the alloys seems more refined for higher temperatures of injection. This refinement in microstructure might play a major role on the mechanical properties of the Al-Si die-cast alloy. (author)

  20. REDUCING REJECTION/REWORK IN PRESSURE DIE CASTING PROCESS BY APPLICATION OF DMAIC METHODOLOGY OF SIX SIGMA

    Javedhusen Malek

    2015-12-01

    Full Text Available In today's ever-changing customer driven market, industries are needed to improve their products and processes to satisfy customer requirements. The Six Sigma approach has set a new paradigm of business excellence. Six Sigma as a process driven improvement methodology has been adopted successfully by many industries. From the review of various literatures, it is revealed that Six Sigma is well adopted in large scale enterprise but having less evidence of adoption in Indian SMEs. This paper is focused on providing path to Indian SMEs for initiating Six Sigma approach in their industries. The paper discusses the real life case where Six Sigma has been successfully applied at one of the Indian small-scale unit to improve rejection/rework rate in manufacturing products by pressure die casting process. This paper describes phase wise application of all the phases of define-measure-analyse-improve-control (DMAIC which also shows impact of Six Sigma in quality improvement.

  1. Microstructural stability of heat-resistant high-pressure die-cast Mg-4Al-4Ce alloy

    Wang, Wei; Zhang, Jinghuai; Li, Guoqiang; Feng, Yan; Su, Minliang; Wu, Ruizhi; Zhang, Zhongwu [Harbin Engineering Univ. (China). Key Laboratory of Superlight Material and Surface Technology; Jiao, Yufeng [Jiamusi Univ. (China). College of Materials Science and Engineering

    2017-05-15

    The thermal stability of Al-RE (rare earth) intermetallic phases with individual RE for heat-resistant high-pressure die-casting Mg-Al-RE alloys is investigated. The results of this study show that the main strengthening phase of Mg-4Al-4Ce alloy is Al{sub 11}Ce{sub 3}, whose content is about 5 wt.% according to quantitative X-ray diffraction phase analysis. The Al{sub 11}Ce{sub 3} phase appears to have high thermal stability at 200 C and 300 C, while phase morphology change with no phase structure transition could occur for Al{sub 11}Ce{sub 3} when the temperature reaches 400 C. Furthermore, besides the kinds of rare earths and temperature, stress is also an influencing factor in the microstructural stability of Mg-4Al-4Ce alloy.

  2. Fabrication of ZnO Nanowires Arrays by Anodization and High-Vacuum Die Casting Technique, and Their Piezoelectric Properties

    Kuo, Chin-Guo; Chang, Ho; Wang, Jian-Hao

    2016-01-01

    In this investigation, anodic aluminum oxide (AAO) with arrayed and regularly arranged nanopores is used as a template in the high-vacuum die casting of molten zinc metal (Zn) into the nanopores. The proposed technique yields arrayed Zn nanowires with an aspect ratio of over 600. After annealing, arrayed zinc oxide (ZnO) nanowires are obtained. Varying the anodizing time yields AAO templates with thicknesses of approximately 50 μm, 60 μm, and 70 μm that can be used in the fabrication of nanowires of three lengths with high aspect ratios. Experimental results reveal that a longer nanowire generates a greater measured piezoelectric current. The ZnO nanowires that are fabricated using an alumina template are anodized for 7 h and produce higher piezoelectric current of up to 69 pA. PMID:27023546

  3. Fabrication of ZnO Nanowires Arrays by Anodization and High-Vacuum Die Casting Technique, and Their Piezoelectric Properties

    Chin-Guo Kuo

    2016-03-01

    Full Text Available In this investigation, anodic aluminum oxide (AAO with arrayed and regularly arranged nanopores is used as a template in the high-vacuum die casting of molten zinc metal (Zn into the nanopores. The proposed technique yields arrayed Zn nanowires with an aspect ratio of over 600. After annealing, arrayed zinc oxide (ZnO nanowires are obtained. Varying the anodizing time yields AAO templates with thicknesses of approximately 50 μm, 60 μm, and 70 μm that can be used in the fabrication of nanowires of three lengths with high aspect ratios. Experimental results reveal that a longer nanowire generates a greater measured piezoelectric current. The ZnO nanowires that are fabricated using an alumina template are anodized for 7 h and produce higher piezoelectric current of up to 69 pA.

  4. Fabrication of ZnO Nanowires Arrays by Anodization and High-Vacuum Die Casting Technique, and Their Piezoelectric Properties.

    Kuo, Chin-Guo; Chang, Ho; Wang, Jian-Hao

    2016-03-24

    In this investigation, anodic aluminum oxide (AAO) with arrayed and regularly arranged nanopores is used as a template in the high-vacuum die casting of molten zinc metal (Zn) into the nanopores. The proposed technique yields arrayed Zn nanowires with an aspect ratio of over 600. After annealing, arrayed zinc oxide (ZnO) nanowires are obtained. Varying the anodizing time yields AAO templates with thicknesses of approximately 50 μm, 60 μm, and 70 μm that can be used in the fabrication of nanowires of three lengths with high aspect ratios. Experimental results reveal that a longer nanowire generates a greater measured piezoelectric current. The ZnO nanowires that are fabricated using an alumina template are anodized for 7 h and produce higher piezoelectric current of up to 69 pA.

  5. Rapid die manufacturing - high pressure casting of low volume non ferrous metals components

    Pereira, MFV

    2006-11-01

    Full Text Available .csir.co.za Models of assembled Die Slide 12 © CSIR 2006 www.csir.co.za 3. Die manufacture, assembly and data capturing 21.521.521.525.5total 4electrode 3Fitting3Fitting3Fitting3Fitting 2Polish2Polish2Polish2Polish 7SER 3F grind3F grind...3F grind4F grind Heat trHeat trHeat tr1Heat tr Jig boreJig boreJig boreJig bore GrindingGrindingGrinding2Grinding 13.5DMLS13.5DMLS13.5DMLS2.5Milling HrsCostProcessHrsCostProcessHrsCostProcessHrsCostProcess Core 4Core 3Core 2Core 1 NB. Times...

  6. Die-cast heterophase composites with AlSi13Mg1CuNi matrix

    M. Dyzia

    2010-01-01

    Full Text Available On the basis of the performed tests, an advantageous interaction of glassy carbon particles in a couple consisting of a heterophase composite and a spheroidal cast iron has been corroborated. It was found that, the presence of glassy carbon in the heterophase composite (SiC+C affects the stabilization of the friction coefficient value as a function of the friction distance and reduces the intensity of the wearing-in stage of the interacting surfaces. Both a decrease of the friction coefficient and the wear of the heterophase composites may be connected with the carbon particles' chipping effect and the deposition of its fragments on the surface of the interacting components of the friction couple, which forms a kind of a solid lubricating agent in the system. This should allow applying of this material to the composite piston - cylinder sleeve system in piston air-compressors. Further works will concern the selection of the matrix alloy composition with the purpose of reducing the phenomenon of particles chipping during machining. It seems that one of the possibilities is the application of a more plastic matrix and optimizing the fraction of reinforcing phases and their gradient distribution in the casting.

  7. Solidification and casting

    Cantor, Brian

    2002-01-01

    INDUSTRIAL PERSPECTIVEDirect chillcasting of aluminium alloysContinuous casting of aluminium alloysContinuous casting of steelsCastings in the automotive industryCast aluminium-silicon piston alloysMODELLING AND SIMULATIONModelling direct chill castingMold filling simulation of die castingThe ten casting rulesGrain selection in single crystal superalloy castingsDefects in aluminium shape castingPattern formation during solidificationPeritectic solidificationSTRUCTURE AND DEFECTSHetergeneous nucleation in aluminium alloysCo

  8. Modelling of Filling, Microstructure Formation, Local Mechanical Properties and Stress – Strain Development in High-Pressure Die Cast Aluminium Castings

    Kotas, Petr; Hattel, Jesper Henri; Thorborg, Jesper

    2009-01-01

    .e. whether the casting is based on cast iron- or aluminium-alloys. The distribution of local properties in a casting might vary substantially which makes it complex to optimize the casting with good accuracy. Often, mechanical simulations of the load situation are based on the assumption that the cast...... in an aluminium alloy is considered including simulation of the entire casting process with emphasis on microstructure formation related to mechanical properties such as elastic modulus, yield stress, ultimate strength and elongation as well as residual stresses. Subsequently, the casting is subjected to service...... loads and the results of this analysis are discussed in relation to the predicted local properties as well as the residual stresses originating from the casting simulation....

  9. The effect of natural pre-ageing on the mechanical properties of Rheo-High pressure die cast aluminium alloy 2139

    Chauke, L

    2015-07-01

    Full Text Available -high pressure die casting process (R-HPDC). Alloy 2139 is a Ag-containing aluminium alloy from the Al-Cu-Mg 2xxx series family. The addition of Ag enhances the age hardening response through the formation of co-clusters that act as precursors to the formation...

  10. The Influence of Pressure Die Casting Parameters on the Mechanical Properties of AlSi11/10 Vol.% SiC Composite

    Konopka Z.

    2014-03-01

    Full Text Available The paper presents the method of preparing a composite slurry composed of AlSi11 alloy matrix and 10 vol.% of SiC particles, as well as the method of its high-pressure die casting and the measurement results concerning the tensile strength, the yield point, the elongation and hardness of the obtained composite. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. There were found the regression equations describing the change of mechanical properties of the examined composite as a function of pressure die casting process parameters. The conclusion gives the analysis and the interpretation of the obtained results.

  11. The Influence of Pressure Die Casting Parameters on Distribution of Reinforcing Particles in the AlSi11/10% SiC Composite

    Pasieka A.

    2013-09-01

    Full Text Available The method of pressure die casting of composites with AlSi11 alloy matrix reinforced with 10 vol. % of SiC particles and the analysis of the distribution of particles within the matrix is presented. The composite castings were produced at various values of the piston velocity in the second stage of injection, at diverse intensification pressure values, and various injection gate width values. The distribution of particles over the entire cross-section of the tensile specimen is shown. The index of distribution was determined on the basis of particle count in elementary measuring fields. The regression equation describing the change of the considered index was found as a function of the pressure die casting parameters. The conclusion presents an analysis of the obtained results and their interpretation.

  12. Pressing Speed, Specific Pressure and Mechanical Properties of Aluminium Cast

    Gaspar S.

    2016-06-01

    Full Text Available Recent research in the process of aluminum alloy die castings production, which is nowadays deeply implemented into the rapidly growing automobile, shipping and aircraft industries, is aimed at increasing the useful qualitative properties of the die casting in order to obtain its high mechanical properties at acceptable economic cost. Problem of technological factors of high pressure die casting has been a subject of worldwide research (EU, US, Japan, etc.. The final performance properties of die castings are subjected to a large number of technological factors. The main technological factors of high pressure die casting are as follows: plunger pressing speed, specific (increase pressure, mold temperature as well as alloy temperature. The contribution discusses the impact of the plunger pressing speed and specific (increase pressure on the mechanical properties of the casting aluminum alloy.

  13. Morphology transition of the primary silicon particles in a hypereutectic A390 alloy in high pressure die casting.

    Wang, J; Guo, Z; Song, J L; Hu, W X; Li, J C; Xiong, S M

    2017-11-03

    The microstructure of a high-pressure die-cast hypereutectic A390 alloy, including PSPs, pores, α-Al grains and Cu-rich phases, was characterized using synchrotron X-ray tomography, together with SEM, TEM and EBSD. The Cu-rich phases exhibited a net morphology and distributed at the boundaries of the α-Al grains, which in turn surrounded the PSPs. Statistical analysis of the reconstructed 1000 PSPs showed that both equivalent diameter and shape factor of the PSPs exhibited a unimodal distribution with peaks corresponding to 25 μm and 0.78, respectively.) PSPs morphology with multiple twinning were observed and morphological or growth transition of the PSPs from regular octahedral shape (with a shape factor of 0.85 was mainly caused by the constraint of the Cu-rich phases. In particular, the presence of the Cu-rich phases restricted the growth of the α-Al grains, inducing stress on the internal silicon particles, which caused multiple twinning occurrence with higher growth potential and consequently led to growth transitions of the PSPs.

  14. Study on the Surface Microstructure of a Modified STD61 Steel Mold Used for the Die Casting Process

    Yu, Ha-Young; Lee, Seung-Joon; Kang, Minwoo; Lee, Suk-Jin; Lee, Young-Kook [Yonsei University, Seoul (Korea, Republic of); Yang, Won Jon [Korea Institute of Materials Science, Changwon (Korea, Republic of); Jeong, Jae Suk; Kim, Byung-Hoon [Doosan Heavy Industries and Construction, Changwon (Korea, Republic of)

    2016-09-15

    The surface microstructure and crack formation of an aluminum die-casting mold were investigated. The mold was made of a modified STD61 steel, and was used for more than 165,000 cycles. The mold surface consisted of four layers; an oxidized layer, a decarburized layer, a network carbide layer and a tempered martensite matrix. The depth down to the hardest network carbide layer was ⁓200 μm. Inside the matrix, M{sub 3}C transition carbides were dissolved so that solute C joined pre-existing M{sub 2}3C{sub 6} and MC carbides to make them coarse. About 60% of thermal fatigue cracks had a depth less than 200 μm due to the hard network carbide layer, which obstructed the propagation of cracks. Cracks of over 200 μm were filled with oxide wedges of Al and Si which was which flown from the molten alloy as well as the Fe oxide.

  15. Microstructure, Tensile Properties, and Corrosion Behavior of Die-Cast Mg-7Al-1Ca- xSn Alloys

    Wang, Feng; Dong, Haikuo; Sun, Shijie; Wang, Zhi; Mao, Pingli; Liu, Zheng

    2018-02-01

    The microstructure, tensile properties, and corrosion behavior of die-cast Mg-7Al-1Ca- xSn ( x = 0, 0.5, 1.0, and 2.0 wt.%) alloys were studied using OM, SEM/EDS, tensile test, weight loss test, and electrochemical test. The experimental results showed that Sn addition effectively refined grains and intermetallic phases and increased the amount of intermetallic phases. Meanwhile, Sn addition to the alloys suppressed the formation of the (Mg,Al)2Ca phase and resulted in the formation of the ternary CaMgSn phase and the binary Mg2Sn phase. The Mg-7Al-1Ca-0.5Sn alloy exhibited best tensile properties at room temperature, while Mg-7Al-1Ca-1.0Sn alloy exhibited best tensile properties at elevated temperature. The corrosion resistance of studied alloys was improved by the Sn addition, and the Mg-7Al-1Ca-0.5Sn alloy presented the best corrosion resistance.

  16. Vacuum Die Casting Process and Simulation for Manufacturing 0.8 mm-Thick Aluminum Plate with Four Maze Shapes

    Chul Kyu Jin

    2015-02-01

    Full Text Available Using vacuum die casting, 0.8 mm-thick plates in complicated shapes are manufactured with the highly castable aluminum alloy Silafont-36 (AlSi9MgMn. The sizes and shapes of the cavities, made of thin plates, feature four different mazes. To investigate formability and mechanical properties by shot condition, a total of six parameters (melt temperatures of 730 °C and 710 °C; plunger speeds of 3.0 m/s and 2.5 m/s; vacuum pressure of 250 mbar and no vacuum are varied in experiments, and corresponding simulations are performed. Simulation results obtained through MAGMA software show similar tendencies to those of the experiments. When the melt pouring temperature is set to 730 °C rather than 710 °C, formability and mechanical properties are superior, and when the plunger speed is set to 3.0 m/s rather than to 2.5 m/s, a fine, even structure is obtained with better mechanical properties. The non-vacuumed sample is half unfilled. The tensile strength and elongation of the sample fabricated under a melt temperature of 730 °C, plunger speed of 3.0 m/s, and vacuum pressure of 250 mbar are 265 MPa and 8.5%, respectively.

  17. 75 FR 54595 - Certain Iron Construction Castings From Brazil, Canada, and the People's Republic of China: Final...

    2010-09-08

    ...] Certain Iron Construction Castings From Brazil, Canada, and the People's Republic of China: Final Results... construction castings from Brazil, Canada, and the People's Republic of China (PRC), pursuant to section 751(c) of the Tariff Act of 1930, as amended (the Act). See Initiation of Five-year (``Sunset'') Review, 75...

  18. Effect of substituting cerium-rich mischmetal with lanthanum on high temperature properties of die-cast Mg-Zn-Al-Ca-RE alloys

    Anyanwu, Ifeanyi A.; Gokan, Yasuhiro; Suzuki, Atsuya; Kamado, Shigeharu; Kojima, Yo; Takeda, Suguru; Ishida, Taketoshi

    2004-01-01

    Mg-Zn-Al-Ca-RE alloys have been found to be promising materials for substituting aluminum alloys used for automatic transmission case applications in the automobile industry. Particularly, Mg-0.5%Zn-6%Al-1%Ca-3%RE (ZAXE05613) alloy exhibits comparable creep resistance as ADC12 die-casting aluminum alloy that is currently used for automatic transmission case applications. Changing the rare earth (RE) content of the alloy from mischmetal to lanthanum gives a further improvement in the creep properties of the alloy. Lanthanum addition results in the crystallization of a large amount of acicular Al 11 RE 3 (Al 11 La 3 ) compound along the grain boundaries as well as across the grain boundaries and this effectively controls grain boundary sliding and dislocation motion in the vicinity of the grain boundaries. As a result, die-cast ZAXLa05613 alloy exhibits a higher creep resistance than that of ZAXE05613 alloy

  19. Endurance in Al Alloy Melts and Wear Resistance of Titanium Matrix Composite Shot-Sleeve for Aluminum Alloy Die-casting

    Choi, Bong-Jae; Kim, Young-Jig; Sung, Si-Young

    2012-01-01

    The main purpose of this study was to evaluate the endurance against Al alloy melts and wear resistance of an in-situ synthesized titanium matrix composite (TMC) sleeve for aluminum alloy die-casting. The conventional die-casting shot sleeve material was STD61 tool steel. TMCs have great thermal stability, wear and oxidation resistance. The in-situ reaction between Ti and B4C leads to two kinds of thermodynamically stable reinforcements, such as TiBw and TiCp. To evaluate the feasibility of the application to a TMCs diecasting shot sleeve, the interfacial reaction behavior was examined between Al alloys melts with TMCs and STD61 tool steel. The pin-on-disk type dry sliding wear test was also investigated for TMCs and STD61 tool steel.

  20. Procedure of a secure design calculation for transmission housings made of aluminium die cast; Ablauf einer sicheren Auslegungsberechnung von Getriebegehaeusen aus Aluminiumdruckguss

    Varenkamp, Marco; Schoen, Michael [ZF Friedrichshafen AG, Friedrichshafen (Germany). Fachbereich Berechnung und Simulation

    2011-07-01

    The challenges in life time calculation of transmission housings made of aluminium die cast are on the one hand the complex geometry of the parts and on the other hand the defects in the material such as pores resulting from the die-cast process. The calculations are carried out using the finite element method and the local strain approach. The problem of transferability within the local strain approach is mastered by comparison with component tests and improvement of the transfer functions based on statistical evaluation. The secure design is assured by a safety factor derived from the confidence probability. With the help of an example the procedure will be explained. In addition it will be shown that under uniaxial variable amplitude loading the calculation result can be improved using the damage parameter PJ. (orig.)

  1. Correlations Between Arrangement of Reinforcing Particles and Mechanical Properties in Pressure Die Cast AlSi11-SiC Composites

    Konopka Z.

    2014-06-01

    Full Text Available The work presents the investigation results concerning the structure of composite pressure die castings with AlSi11 alloy matrix reinforced with SiC particles. Examination has been held for composites containing 10 and 20 volume percent of SiC particles. The arrangement of the reinforcing particles within the matrix has been qualitatively assessed in specimens cut out of the castings. The index of distribution was determined on the basis of particle count in elementary measuring fields. The tensile strength, the yield point and elongation of the obtained composite were measured. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. The regression equation describing the change of the considered arrangement particles index and mechanical properties were found as a function of the pressure die casting parameters. The infuence of particle arrangement in composite matrix on mechanical properties these material was examined and the functions of correlations between values were obtained. The conclusion gives the analysis and the interpretation of the obtained results.

  2. A comparative evaluation of the marginal adaptation of a thermoplastic resin, a light cured wax and an inlay casting wax on stone dies: An in vitro study.

    Gopalan, Reji P; Nair, Vivek V; Harshakumar, K; Ravichandran, R; Lylajam, S; Viswambaran, Prasanth

    2018-01-01

    Different pattern materials do not produce copings with satisfactory, marginal accuracy when used on stone dies at varying time intervals. The purpose of this study was to evaluate and compare the vertical marginal accuracy of patterns formed from three materials, namely, thermoplastic resin, light cured wax and inlay casting wax at three-time intervals of 1, 12, and 24 h. A master die (zirconia abutment mimicking a prepared permanent maxillary central incisor) and metal sleeve (direct metal laser sintering crown #11) were fabricated. A total of 30 stone dies were obtained from the master die. Ten patterns were made each from the three materials and stored off the die at room temperature. The vertical marginal gaps were measured using digital microscope at 1, 12, and 24 h after reseating with gentle finger pressure. The results revealed a significant statistical difference in the marginal adaptation of three materials at all the three-time intervals. Light cured wax was found to be most accurate at all time intervals, followed by thermoplastic resin and inlay casting wax. Furthermore, there was a significant difference between all pairs of materials. The change in vertical marginal gap from 1 to 24 h between thermoplastic resin and light cured wax was not statistically significant. The marginal adaptation of all the three materials used, was well within the acceptable range of 25-70 μm. The resin pattern materials studied revealed significantly less dimensional change than inlay casting wax on storage at 1, 12, and 24 h time intervals. They may be employed in situations where high precision and delayed investing is expected.

  3. Qualification of old wastes for finale disposal; Qualifizierung von Altabfaellen fuer die Endlagerung

    Dullau, R.; Kloeckner, J. [WTI Wissenschaftlich-Technische Ingenieurberatung GmbH, Juelich (Germany); Uekoetter, S. [GNS Gesellschaft fuer Nuklear-Service mbH, Essen (Germany)

    2010-05-15

    In the frame of the interim storage and final disposal of radioactive waste forms until now about 1200 barrels filled with old radioactive waste had to be requalified. The process of requalification is described in this contribution. The storage casks contained mainly high-pressure compacted and loose mixed waste, cemented waste and casting molds, building waste and combustion residuals, conditioned in the 1980ies. In the final repository Morsleben 80% of the waste forms were cleared for final disposal in Morsleben, 20% were qualified for interim storage and final disposal in the Schachtanlage Konrad. Based on these experiences the authors summarize recommendations for further requalification of old waste forms for the disposal in the Schachtanlage Konrad.

  4. Evaluation of interlocking bond strength between structured 1.0338 steel sheets and high pressure die cast AlMg5Si2

    Senge, S.; Brachmann, J.; Hirt, G.; Bührig-Polaczek, A.

    2018-05-01

    Multi-material components open up new possibilities for functional design. Such components combine beneficial physical properties of different materials in a single component as for instance chemical resistance, high strength or low density. The challenge is a reliable bond between both materials to enable a long term usage. This paper deals with a form closure connection to ensure a solid connection between steel strips and high pressure die cast aluminium. Two different sizes of channel structures with width ratios of 1.0 and 1.35 are produced on a steel sheet. An ensuing flat rolling pass is performed to create undercuts with a width of up to 50 µm, enabling an interlocking of the molten aluminium in the concluding casting process. For both rolling processes the resulting geometry is analysed depending on the thickness reduction. In a subsequent high pressure die casting process, aluminium is applied resulting in a complete form filling for the coarser structure. Comparing structures with and without undercuts, only structures suited with undercuts remain gap-free after solidification contraction. The finer structure could not be filled completely; nevertheless these structures result in shear strength of up to 45 MPa transversal to the channel-direction.

  5. ''Heat Transfer at the Mold-Metal Interface in Permanent Mold Casting of Aluminum Alloys'' Final Project Report; FINAL

    Pehlke, R. D.; Cookson, John M.; Shouwei Hao; Prasad Krishna; Bilkey, Kevin T.

    2001-01-01

    This project on heat transfer coefficients in metal permanent mold casting has been conducted in three areas. They are the theoretical study at the University of Michigan, the experimental investigation of squeeze casting at CMI-Tech Center (Now Hayes-Lemmerz Technical Center) and the experimental investigation of low pressure permanent mold casting at Amcast Automotive

  6. The Effect of Water Mist Cooling of Casting Die on the Solidification, Microstructure and Properties of AlSi20 Alloy

    Władysiak R.

    2017-03-01

    Full Text Available Unmodified AlSi20 alloy were casted at the research station, allowing for sequential multipoint cooling using a dedicated computer- controlled program. This method allows for the formation of the microstructure of hypereutectic AlSi20 alloy and also increases hardness. Primary silicon dendrites were found in the microstructure of cooled samples. Based on these dendrites, the formation of primary silicon particles is explained. Cooling of casting die with a water mist stream causes changes in solidification, which leads to expansion of the boundary layer with columnar crystals and shrinkage of the core zone with equiaxed crystals. It also causes more regular hardness distribution around pre-eutectic Si crystals, which can lead to tensile strength and machinability improvement.

  7. Improved life of die casting dies of H13 steel by attaining improved mechanical properties and distortion control during heat treatment. Year 1 report, October 1994--September 1995

    Wallace, J.F.; Schwam, D. [Case Western Reserve Univ., Cleveland, OH (United States)

    1995-03-01

    Optimum heat treatment of dies (quenching) is critical in ensuring satisfactory service performance: rapid cooling rates increase the thermal fatigue/heat checking resistance of the steel, although very fast cooling rates can also lead to distortion and lower fracture toughness, increasing the danger of catastrophic fracture. Goal of this project is to increase die life by using fast enough quenching rates (> 30 F/min ave cooling rate from 1750 to 550 F, 1/2 in. below working surfaces) to obtain good toughness and fatigue resistance in Premium grade H-13 steel dies. An iterative approach of computer modeling validated by experiment was taken. Cooling curves during gas quenching of H-13 blocks and die shapes were measured under 2, 5, and 7.5 bar N2 and 4 bar Ar. Resulting dimensional changes and residual stresses were determined. To facilitate the computer modeling work, a database of H-13 mechanical and physical properties was compiled. Finite element analysis of the heat treated shapes was conducted. Good fit of modeled vs measured quenched rates was demonstrated for simple die shapes. The models predict well the phase transformation products from the quench. There is good fit between predicted and measured distortion contours; however magnitude of predicted distortion and residual stresses does not match well the measured values. Further fine tuning of the model is required.

  8. Investigation of microporosity in die-cast AlSi12(Cu) alloys by neutron- and X-ray radiography

    Zsolt, S.; Marton, B.

    1999-01-01

    The porosity of the casting can dramatically reduce the solidity and reliability of the objects made from aluminum alloys. The X-ray radiography is able to find the placement of the porosity of the aluminum devices. After a special 'water saturation' process the dynamic neutron radiography is available to discover the 'dangerous' surface nearporosity in the aluminum samples. The X-ray and neutron radiography were used as complementary examination techniques to study the porosity of the aluminum castings.(author)

  9. Microstructural and mechanical properties of gravity-die-cast A356 alloy inoculated with yttrium and Al-Ti-B grain refiner simultaneously

    Y.P. Lim

    2011-10-01

    Full Text Available In the present work, the effect of inoculating yttrium and Al-5Ti-1B simultaneously on A356 aluminum alloy has been studied. Gravity die casting process is used to cast the ASTM tensile test specimens for analysis. In each experiment, the Ti and B contents were maintained constantly at 0.1 and 0.02 wt% respectively. The addition of yttrium was manipulated at the amount of 0, 0.1, 0.2, 0.3, 0.4 and 0.5 wt%. Microstructural characterization of the as-cast A356 alloy was investigated by means of optical microscope and its phases are detected by XRD. The mechanical properties tested are tensile strength and hardness. The inoculation of yttrium was found to enhance the grain refinement effect of Al-5Ti-1B grain refiner and improve the mechanical properties. The optimal weight percentage of yttrium was found to be 0.3. The grain refining efficiency of combining yttrium and Al-5Ti-1B on A356 aluminum alloy was mainly attributed to the heterogeneous nucleation of TiB2 and TiAl3 particles which were dispersed more evenly in the presence of yttrium and the grain growth restriction effected by the accumulation of Al-Y compound at grain boundaries.

  10. Microstructure, Mechanical and Surface Morphological Properties of Al5Ti5Cr Master Alloy as Friction Material Prepared by Stir Die Casting

    Ahmed, Syed Faisal; Srivastava, Sanjay; Agarwal, Alka Bani

    2018-04-01

    Metal matrix composite offers outstanding properties for better performance of disc brakes. In the present study, the composite of AlTiCr master alloy was prepared by stir die casting method. The developed material was reinforced with (0-10 wt%) silicon carbide (SiC) and boron carbide (B4C). The effects of SiC reinforcement from 0 to 10 wt% on mechanical, microstructure and surface morphological properties of Al MMC was investigated and compared with B4C reinforcement. Physical properties like density and micro Vickers hardness number show an increasing trend with an increase in the percentage of SiC and B4C reinforcement. Mechanical properties viz. UTS, yield strength and percentage of elongation are improved with increasing the fraction of reinforcement. The surface morphology and phase were identified from scanning electron microscopy (SEM) and X-ray diffraction analysis and the oxidized product formed during the casting was investigated by Fourier transformation infrared spectroscopy. This confirms the presence of crystallization of corundum (α-Al2O3) in small traces as one of the alumina phases, within casting sample. Micro-structural characterization by SEM depicted that the particles tend to be more agglomerated more and more with the percentage of the reinforcement. The AFM results reveal that the surface roughness value shows a decreasing trend with SiC reinforcement while roughness increases with increase the percentage of B4C.

  11. Assembly optimization realized by a die-cast magnesium construction; Montageverbesserungen verwirklicht durch eine Magnesium-Druckguss-Konstruktion

    Tikal, F.; Vollmer, C.; Pippert, J.

    1996-11-01

    Vehicle development today cannot be envisaged without non-contact and slip free distance- and speed-measurement. As it is superior to contact methods in terms of reliability and accuracy, it has gained more and more acceptance in the past few years and now provides measurement results of the utmost precision. This is particularly necessary in the large application range of tyre and vehicle development to ensure high safety levels; moreover, it is required for future vehicle control systems, as they need precise speed information for ABS, ASC, or for navigation methods. In principle, optical acoustic and microwave sensors can be used for these applications. The microwave sensors can be used for these applications. The microwave-Doppler principle provides certain advantages over optical or ultrasound methods as it can be used under any weather conditions and provides a larger vertical operating range and a long lifespan. Datron-Messtechnik, market leader in the field of correlator optical speed sensors, has made use of this measurement principle and with its microwave sensor introduces a new development covering the great demands of speed measurement. (orig.) [Deutsch] Die Pkw-Tuer, ein Bestandteil der Karosserie, ist im Laufe der Automobilgeschichte nicht wesentlich veraendert worden. Jedoch mussten in den letzten Jahren Flankenschutz, Seitenairbag und andere neue Bauteile in die Tuer integriert werden. Diese Elemente der passiven Sicherheit sind vom Verbraucher gewuenschte Schutzmassnahmen. Mit dem gehobenen Sicherheitsimage bemuehen sich die Produzenten, den potentiellen Kaeufer zum Kauf ihres Produktes zu bewegen. Am Institut fuer Produktionstechnik und Logistik (IPL) der Universitaet Gesamthochschule Kassel (GhK) wurde eine Pkw-Tuer, basierend auf einem Magnesium-Druckgussrahmen, entwickelt. Zur Orientierung und Studienzwecken ist ein Holzmodell erstellt worden. Mit dem praxisnahen Modell konnte die Montage und der Einbau in das Automobil getestet werden. Das

  12. Die-cast of a hypo-eutectic AL-SI alloy: influence of injection temperature on microstructure and mechanical properties; Fundicao sob pressao das ligas de AL-SI: influencia da temperatura de injecao nas microestruturas e propriedades mecanicas

    Santos, Silvano Leal dos; Santos, Sydney Ferreira, E-mail: silvano_lleal@yahoo.com.br [Universidade Federal do ABC (UFABC), SP (Brazil)

    2014-07-01

    Die-casting is widely used for manufacturing light alloy components for automotive industry. Among others, hypo-eutectic Al-Si alloys are currently processed by die-casting. To obtain high quality die-cast components, a better understanding on the correlations between processing parameters, microstructures, and mechanical properties are of utmost importance. In this study, we investigate the effect of injection temperature of liquid metal on the microstructure and mechanical properties of Al-Si alloy EN AC 46000 (DIN designation). The injection temperatures were 579, 589, 643, and 709 deg C. As-cast components had their microstructures analyzed by X-ray diffraction, optical and scanning electron microscopy, and X-ray energy dispersive spectroscopy. The mechanical properties were examined by micro-hardness and tensile tests. It was observed that the ultimate tensile strength slightly increased with the increase of injection temperature. The same trend was observed for micro-hardness. The amount of porosity in the samples varies in a small amount for different injection temperatures. On the other hand, the microstructure of the alloys seems more refined for higher temperatures of injection. This refinement in microstructure might play a major role on the mechanical properties of the Al-Si die-cast alloy. (author)

  13. Effect of Heat Treatment on Commercial AlSi12Cu1(Fe) and AlSi12(b) Aluminum Alloy Die Castings

    Battaglia, E.; Bonollo, F.; Ferro, P.; Fabrizi, A.

    2018-03-01

    High-pressure die castings (HPDCs) cannot normally be heat-treated at a high temperature because of the presence of inner air/gas- or shrinkage-porosity that may lead to the formation of undesired surface blisters. In this paper, an unconventional heat treatment is proposed. Two secondary Al-Si alloys, AlSi12(b) and AlSi12Cu1(Fe), were stabilization heat-treated at 624 K (350 °C) with soaking times ranging from 1 to 8 hours. Enhancement of both static and dynamic mechanical properties was found to be related to the fragmentation of interconnected eutectic Si particles and the smoothing of coarser crystals. Increased ductility after heat treatment was correlated with a decrease in hardness and Si particle roundness. The formation of Si precipitates within the α-Al matrix was also observed.

  14. SPRAY CASTING

    SALAMCI, Elmas

    2010-01-01

    ABSTRACT This paper is designed to provide a basic review of spray casting. A brief overview of the historical development of spray  casting and the description of plant and equipment have been given. Following metallurgical characteristics of spray formed alloys, process parameters and solidification mechanism of spray deposition have been discussed in detail. Finally, microstructure and mechanical properties of the selected spray cast Al-Zn-Mg-Cu alloys have been presented and comp...

  15. Morphology and Performance of 5Cr5MoV Casting Die Steel in the Process of Surfacing

    Song, Yulai; Kong, Xiangrui; Yang, Pengcong; Fu, Hongde; Wang, Xuezhu

    2017-12-01

    To investigate the microstructures and mechanical properties of the deposited metal on surface of die steel, two layer of weld-seam were prepared on the surface of 5Cr5MoV die steel by arc surfacing. The surface microstructures and microhardness were characterized by scanning electron microscopy, energy dispersive spectrometer and Vickers microhardness tester, respectively. The effect of load on the abrasion resistance and wear mechanism of the base metal and surfacing metal was studied by pin-on-disk tribometer. The results showed that martensite and retained austenite exist in weld-seam, both of them grow up in the form of dendrites and equiaxed grains and microhardness reach 774.2HV. The microstructures of the quenching zone mainly consist of martensite and retained austenite, while tempered martensite is the dominant phase in partial quenching zone. The abrasion resistance of the surfacing metal is superior to the base metal based on the results of wear test. The wear rates of surfacing metal and base metal raise with the increase of load. The wear rates of base metal raise extremely when the load reach 210N. Both of two kinds of materials have the similar wear mechanism, namely, abrasive wear at low load, oxidative wear and adhesive wear at high load.

  16. HANFORD CONTAINERIZED CAST STONE FACILITY TASK 1 PROCESS TESTING & DEVELOPMENT FINAL TEST REPORT

    LOCKREM, L L

    2005-07-13

    Laboratory testing and technical evaluation activities on Containerized Cast Stone (CCS) were conducted under the Scope of Work (SOW) contained in CH2M HILL Hanford Group, Inc. (CHG) Contract No. 18548 (CHG 2003a). This report presents the results of testing and demonstration activities discussed in SOW Section 3.1, Task I--''Process Development Testing'', and described in greater detail in the ''Containerized Grout--Phase I Testing and Demonstration Plan'' (CHG, 2003b). CHG (2003b) divided the CCS testing and evaluation activities into six categories, as follows: (1) A short set of tests with simulant to select a preferred dry reagent formulation (DRF), determine allowable liquid addition levels, and confirm the Part 2 test matrix. (2) Waste form performance testing on cast stone made from the preferred DRF and a backup DRF, as selected in Part I, and using low activity waste (LAW) simulant. (3) Waste form performance testing on cast stone made from the preferred DRF using radioactive LAW. (4) Waste form validation testing on a selected nominal cast stone formulation using the preferred DRF and LAW simulant. (5) Engineering evaluations of explosive/toxic gas evolution, including hydrogen, from the cast stone product. (6) Technetium ''getter'' testing with cast stone made with LAW simulant and with radioactive LAW. In addition, nitrate leaching observations were drawn from nitrate leachability data obtained in the course of the Parts 2 and 3 waste form performance testing. The nitrate leachability index results are presented along with other data from the applicable activity categories.

  17. Triple Plate Mold Final Report: Optimization of the Mold Design and Casting Parameters for a Thin U-10mo Fuel Casting

    Aikin, Jr., Robert M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-01-04

    This work describes the experiments and modeling that have been performed to improve and try to optimize the simultaneous casting of three plates of U-10wt%Mo in a single coil vacuum induction melting (VIM) furnace. The plates of interest are 280 mm wide by 203 mm tall by 5 mm thick (11" x 8" x 0.2"). The initial mold design and processing parameters were supplied by Y-12. The mold and casting cavity were instrumented with a number of thermocouples, and the casting performed to determine the thermal history of the mold and casting. The resulting cast plates were radiographed and numerous defects identified. Metallography was performed to help identify the nature of the radiographically observed defects. This information was then used to validate a mold filling and solidification model of that casting. Based on the initial casting, good casting design practice, and process simulation of several design alternatives, a revised design was developed with the goal of minimizing casting defects such as porosity. The redesigned mold had a larger hot-top and had its long axis along the horizontal direction. These changes were to try to develop a strong thermal gradient conducive to good feeding and minimization of micro- and macroporosity in the cast plates. An instrumented casting was then performed with the revised mold design and a linear distributor. This design yielded cast plates with significantly less radiographically identified defects. Unfortunately, there was significant variation in plate weight and metal content in their hot-tops. Fluid flow simulations were then performed on this mold/distributor design. This helped identify the issue with this linear distributor design. Additional simulations were then performed on candidate distributor redesigns and a preferred distributor annular design was identified. This improved annular design was used to produce a third instrumented casting with favorable results. These refined designs and their radiographic

  18. Re-Engineering Casting Production Systems - Final Report - 03/02/1998 - 03/01/2001; FINAL

    Peters, Frank; Van Voorhis, Timothy

    2001-01-01

    The goal of this three-year project was to improve the production systems in use by steel foundries in the United States. Improvements in the production systems result in less rework, less scrap, and less material handling, all of which would significantly reduce the energy demands of the process. Furthermore, these improvements would allow the companies to be more competitive, more responsive to customers' needs, deliver products with less lead time and require less capital. The ultimate result is a stronger domestic steel casting industry, which uses less energy. A major portion of this research involved the deployment of student researchers at steel foundries, to study their production systems and collect data

  19. Synergistic effects of composition and heat treatment on microstructure and properties of vacuum die cast Al-Si-Mg-Mn alloys

    Jun-jie Xu

    2018-03-01

    Full Text Available The purpose of this study was to prepare high-quality Al-Si-Mg-Mn alloy with a good combination of strength and ductility employing the vacuum-assisted high-pressure die cast process. An orthogonal study of heat treatments was conducted to design an optimized T6 heat treatment process for both Al-10%Si-0.3%Mg-Mn and Al-11%Si-0.6%Mg-Mn alloys. The results demonstrate that no obvious blisters and warpage were observed in these two alloys with solid solution treatment. After the optimal T6 heat treatment of 530°C×3h + 165°C×6h, Al-11%Si-0.6%Mg-Mn alloy has better mechanical properties, of which tensile strength, yield strength and elongation reached 377.3 MPa, 307.8 MPa and 9%, respectively. The improvement of mechanical properties can be attributed to the high density of needle-like β″(Mg5Si6 precipitation after aging treatment and the fine and spherical eutectic Si particles uniformly distributed in the α-Al matrix.

  20. On the microstructural factors affecting creep resistance of die-cast Mg–La-rare earth (Nd, Y or Gd) alloys

    Gavras, S. [Magnesium Innovation Centre, Helmholtz-Zentrum Geesthacht, Max-Planck-Straße 1, Geesthacht (Germany); Zhu, S.M. [School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Carlton, Victoria 3053 (Australia); Nie, J.F. [Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); Gibson, M.A. [School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Carlton, Victoria 3053 (Australia); Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); CSIRO Manufacturing, Clayton, Victoria 3168 (Australia); Easton, M.A. [School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Carlton, Victoria 3053 (Australia)

    2016-10-15

    Creep properties of high-pressure die-cast Mg–La-RE (Nd, Y or Gd) alloys, varying in ternary RE additions and in different heat treatment conditions, have been investigated. Through the use of short-term solution treatments (1 h at 520 °C) it was shown that the continuous intermetallic phase present in the eutectic at grain boundaries became discontinuous. This effect, in combination with the likely removal of the localised region of supersaturated solute in solid solution near grain boundaries, reduced the creep resistance. When relatively high concentrations of ternary alloying additions were used, solid solution strengthening and precipitation hardening appeared to compensate for the negative effect of reduced grain boundary reinforcement. Microstructural investigation revealed that Nd-containing alloys had fewer and larger dynamic precipitates present in the α-Mg matrix following creep testing at 177 °C and 90 MPa. It was concluded that grain boundary reinforcement in combination with the thermal stability of the precipitates formed, which is ultimately related to the diffusivity of solute in solid solution, are also contributing factors to creep resistance.

  1. Strengthening effect of nano-scale precipitates in a die-cast Mg–4Al–5.6Sm–0.3Mn alloy

    Yang, Qiang [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Bu, Fanqiang [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Qiu, Xin [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Yangzhou Hongfu Aluminium Co. Ltd, Yangzhou 100049 (China); Li, Yangde; Li, Weirong [E-ande Scientific & Technology Co. Ltd, Dongguan 523000 (China); Sun, Wei [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Liu, Xiaojuan, E-mail: lxjuan@ciac.ac.cn [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Meng, Jian, E-mail: jmeng@ciac.jl.cn [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China)

    2016-04-25

    In this paper we report a quantitative study of the age-hardening in the high-pressure die-cast Mg–4Al−5.6Sm−0.3Mn alloy. The results indicate that a number of nano-scale spherical precipitates identified as Al{sub 3}Sm using high-angle annular dark-field scanning transmission electron microscopy, precipitated in Mg matrix after aging at 150–225 °C, with no obvious changes on grain sizes, intermetallic phases formed during solidification, and dislocation densities. From the existing strengthening theory equations in which some lacking parameters were taken from the first-principles density functional theory (DFT) calculations, a quantitative insight into the strengthening mechanisms of the nano-scale precipitate was formulated. The results are in reasonable agreement with the experimental values, and the operative mechanism of precipitation strengthening was revealed as Orowan dislocation bypassing. - Highlights: • The yield strength of Mg–Al–Sm alloy was improved by aging treatment. • A number of nano-scale precipitates formed in matrix after aging treatments. • The nanoscale precipitate was confirmed as Al{sub 3}Sm based on the data of HAADF-STEM study. • The strengthening mechanisms of the nano-scale precipitate were quantitatively formulated. • The operative mechanism of precipitate strengthening is Orowan dislocation bypassing.

  2. Corrosion Behavior of High Pressure Die Cast Al-Ni and Al-Ni-Ca Alloys in 3.5% NaCl Solution

    Arthanari, Srinivasan; Jang, Jae Cheol; Shin, Kwang Seon [Seoul National University, Seoul (Korea, Republic of)

    2017-06-15

    In this investigation corrosion behavior of newly developed high-pressure die cast Al-Ni (N15) and Al-Ni-Ca (NX1503) alloys was studied in 3.5% NaCl solution. The electrochemical corrosion behavior was evaluated using open circuit potential (OCP) measurement, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) techniques. Potentiodynamic polarization results validated that NX1503 alloy exhibited lower corrosion current density (i{sub corr}) value (5.969 μA/cm{sup 2}) compared to N15 (7.387 μA/cm{sup 2}). EIS-Bode plots revealed a higher impedance (|Z|) value and maximum phase angle value for NX1503 than N15 alloy. Equivalent circuit curve fitting analysis revealed that surface layer (R{sub 1}) and charge transfer resistance (R{sub ct}) values of NX1503 alloy was higher compared to N15 alloy. Immersion corrosion studies were also conducted for alloys using fishing line specimen arrangement to simultaneously measure corrosion rates from weight loss (P{sub W}) and hydrogen volume (P{sub H}) after 72 hours and NX1503 alloy had lower corrosion rate compared to N15 alloy. The addition of Ca to N15 alloy significantly reduced the Al{sub 3}Ni intermetallic phase and further grain refinement may be attributed for reduction in the corrosion rate.

  3. Final Report, Volume 2, The Development of Qualification Standards for Cast Duplex Stainless Steel

    Russell, Steven, W.; Lundin, Carl, D.

    2005-09-30

    The scope of testing cast Duplex Stainless Steel (DSS) required testing to several ASTM specifications, while formulating and conducting industry round robin tests to verify and study the reproducibility of the results. ASTM E562 (Standard Test Method for Determining Volume Fraction by Systematic manual Point Count) and ASTM A923 (Standard Test Methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic/Ferritic Stainless Steels) were the specifications utilized in conducting this work. An ASTM E562 industry round robin, ASTM A923 applicability study, ASTM A923 industry round robin, and an ASTM A923 study of the effectiveness of existing foundry solution annealing procedures for producing cast DSS without intermetallic phases were implemented. In the ASTM E562 study, 5 samples were extracted from various cast austenitic and DSS in order to have varying amounts of ferrite. Each sample was metallographically prepared by UT and sent to each of 8 participants for volume fraction of ferrite measurements. Volume fraction of ferrite was measured using manual point count per ASTM E562. FN was measured from the Feritescope{reg_sign} and converted to volume fraction of ferrite. Results indicate that ASTM E562 is applicable to DSS and the results have excellent lab-to-lab reproducibility. Also, volume fraction of ferrite conversions from the FN measured by the Feritescope{reg_sign} were similar to volume fraction of ferrite measured per ASTM E562. In the ASTM A923 applicability to cast DSS study, 8 different heat treatments were performed on 3 lots of ASTM A890-4A (CD3MN) castings and 1 lot of 2205 wrought DSS. The heat treatments were selected to produce a wide range of cooling rates and hold times in order to study the suitability of ASTM A923 to the response of varying amounts on intermetallic phases [117]. The test parameters were identical to those used to develop ASTM A923 for wrought DSS. Charpy V-notch impact samples were extracted from the

  4. Final Report, Volume 2, The Development of Qualification Standards for Cast Duplex Stainless Steel

    Russell, Steven, W.; Lundin, Carl, W.

    2005-09-30

    The scope of testing cast Duplex Stainless Steel (DSS) required testing to several ASTM specifications, while formulating and conducting industry round robin tests to verify and study the reproducibility of the results. ASTM E562 (Standard Test Method for Determining Volume Fraction by Systematic manual Point Count) and ASTM A923 (Standard Test Methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic/Ferritic Stainless Steels) were the specifications utilized in conducting this work. An ASTM E562 industry round robin, ASTM A923 applicability study, ASTM A923 industry round robin, and an ASTM A923 study of the effectiveness of existing foundry solution annealing procedures for producing cast DSS without intermetallic phases were implemented. In the ASTM E562 study, 5 samples were extracted from various cast austenitic and DSS in order to have varying amounts of ferrite. Each sample was metallographically prepared by UT and sent to each of 8 participants for volume fraction of ferrite measurements. Volume fraction of ferrite was measured using manual point count per ASTM E562. FN was measured from the Feritescope® and converted to volume fraction of ferrite. Results indicate that ASTM E562 is applicable to DSS and the results have excellent lab-to-lab reproducibility. Also, volume fraction of ferrite conversions from the FN measured by the Feritescope® were similar to volume fraction of ferrite measured per ASTM E562. In the ASTM A923 applicability to cast DSS study, 8 different heat treatments were performed on 3 lots of ASTM A890-4A (CD3MN) castings and 1 lot of 2205 wrought DSS. The heat treatments were selected to produce a wide range of cooling rates and hold times in order to study the suitability of ASTM A923 to the response of varying amounts on intermetallic phases [117]. The test parameters were identical to those used to develop ASTM A923 for wrought DSS. Charpy V-notch impact samples were extracted from the castings and wrought

  5. Grain refinement of permanent mold cast copper base alloys. Final report

    Sadayappan, M.; Thomson, J. P.; Elboujdaini, M.; Gu, G. Ping; Sahoo, M.

    2004-04-29

    Grain refinement behavior of copper alloys cast in permanent molds was investigated. This is one of the least studied subjects in copper alloy castings. Grain refinement is not widely practiced for leaded copper alloys cast in sand molds. Aluminum bronzes and high strength yellow brasses, cast in sand and permanent molds, were usually fine grained due to the presence of more than 2% iron. Grain refinement of the most common permanent mold casting alloys, leaded yellow brass and its lead-free replacement EnviroBrass III, is not universally accepted due to the perceived problem of hard spots in finished castings and for the same reason these alloys contain very low amounts of iron. The yellow brasses and Cu-Si alloys are gaining popularity in North America due to their low lead content and amenability for permanent mold casting. These alloys are prone to hot tearing in permanent mold casting. Grain refinement is one of the solutions for reducing this problem. However, to use this technique it is necessary to understand the mechanism of grain refinement and other issues involved in the process. The following issues were studied during this three year project funded by the US Department of Energy and the copper casting industry: (1) Effect of alloying additions on the grain size of Cu-Zn alloys and their interaction with grain refiners; (2) Effect of two grain refining elements, boron and zirconium, on the grain size of four copper alloys, yellow brass, EnviroBrass II, silicon brass and silicon bronze and the duration of their effect (fading); (3) Prediction of grain refinement using cooling curve analysis and use of this method as an on-line quality control tool; (4) Hard spot formation in yellow brass and EnviroBrass due to grain refinement; (5) Corrosion resistance of the grain refined alloys; (6) Transfer the technology to permanent mold casting foundries; It was found that alloying elements such as tin and zinc do not change the grain size of Cu-Zn alloys

  6. Mechanism and application of a newly developed pressure casting process: horizontal squeeze casting

    Li Peijie

    2014-07-01

    Full Text Available Compared to traditional high-pressure die casting (HPDC, horizontal squeeze casting (HSC is a more promising way to fabricate high-integrity castings, owing to a reduced number of gas and shrinkage porosities produced in the casting. In this paper, the differences between HSC and HPDC are assessed, through which it is shown that the cavity filling velocity and the size of the gating system to be the most notable differences. Equipment development and related applications are also reviewed. Furthermore, numerical simulation is used to analyze the three fundamental characteristics of HSC: slow cavity filling, squeeze feeding and slow sleeve filling. From this, a selection principle is given based on the three related critical casting parameters: cavity filling velocity, gate size and sleeve filling velocity. Finally, two specific applications of HSC are introduced, and the future direction of HSC development is discussed.

  7. Microstructure and property evaluation of high-pressure die-cast Mg–La–rare earth (Nd, Y or Gd) alloys

    Gavras, Serge; Easton, Mark A.; Gibson, Mark A.; Zhu, Suming; Nie, Jian-Feng

    2014-01-01

    Highlights: • Different rare earth elements have remarkably different effects on Mg castability. • For the addition of each RE element, the alloy castability follows a unique pattern. • The effects of RE elements on the castability can be modelled. - Abstract: Microstructure, castability and tensile properties were investigated in high-pressure die-cast Mg–La–Nd, Mg–La–Y and Mg–La–Gd alloy series, with a constant La concentration at approximately 2.5 wt.% and the concentrations of Nd, Y or Gd were varied. All three alloy series had a dendritic microstructure with a Mg–La-rich eutectic with increasing Nd, Y or Gd content and containing a Mg 12 RE intermetallic phase. The morphology of the eutectic at ternary alloying additions of equal to or less than 1.0 wt.% was lamellar but became increasingly divorced at higher ternary concentrations. This was however more obvious in Mg–La–Y and Mg–La–Gd than Mg–La–Nd alloys. The hot tearing susceptibility in all three alloy series increased markedly with even micro-alloying additions of Nd, Y or Gd, and began to decrease again in alloys with more than 0.5 wt.% Y or 1.0 wt.% Gd, but did not decrease significantly for Mg–La–Nd. A model using the temperature–fraction solid curves as input parameters was used to estimate hot tearing susceptibility for Mg–La–Nd alloys. Tensile testing at room temperature showed that Mg–La–Nd alloy series had higher 0.2% proof stress and lower elongation to failure than either the Mg–La–Y or the Mg–La–Gd alloy series for Nd concentrations greater than 1 wt.% due to a greater effectiveness of grain boundary reinforcement

  8. Tensile Properties and Fracture Behavior of Aluminum Alloy Foam Fabricated from Die Castings without Using Blowing Agent by Friction Stir Processing Route.

    Hangai, Yoshihiko; Kamada, Hiroto; Utsunomiya, Takao; Kitahara, Soichiro; Kuwazuru, Osamu; Yoshikawa, Nobuhiro

    2014-03-21

    Al foam has been used in a wide range of applications owing to its light weight, high energy absorption and high sound insulation. One of the promising processes for fabricating Al foam involves the use of a foamable precursor. In this study, ADC12 Al foams with porosities of 67%-78% were fabricated from Al alloy die castings without using a blowing agent by the friction stir processing route. The pore structure and tensile properties of the ADC12 foams were investigated and compared with those of commercially available ALPORAS. From X-ray computed tomography (X-ray CT) observations of the pore structure of ADC12 foams, it was found that they have smaller pores with a narrower distribution than those in ALPORAS. Tensile tests on the ADC12 foams indicated that as their porosity increased, the tensile strength and tensile strain decreased, with strong relation between the porosity, tensile strength, and tensile strain. ADC12 foams exhibited brittle fracture, whereas ALPORAS exhibited ductile fracture, which is due to the nature of the Al alloy used as the base material of the foams. By image-based finite element (FE) analysis using X-ray CT images corresponding to the tensile tests on ADC12 foams, it was shown that the fracture path of ADC12 foams observed in tensile tests and the regions of high stress obtained from FE analysis correspond to each other. Therefore, it is considered that the fracture behavior of ADC12 foams in relation to their pore structure distribution can be investigated by image-based FE analysis.

  9. Tensile Properties and Fracture Behavior of Aluminum Alloy Foam Fabricated from Die Castings without Using Blowing Agent by Friction Stir Processing Route

    Yoshihiko Hangai

    2014-03-01

    Full Text Available Al foam has been used in a wide range of applications owing to its light weight, high energy absorption and high sound insulation. One of the promising processes for fabricating Al foam involves the use of a foamable precursor. In this study, ADC12 Al foams with porosities of 67%–78% were fabricated from Al alloy die castings without using a blowing agent by the friction stir processing route. The pore structure and tensile properties of the ADC12 foams were investigated and compared with those of commercially available ALPORAS. From X-ray computed tomography (X-ray CT observations of the pore structure of ADC12 foams, it was found that they have smaller pores with a narrower distribution than those in ALPORAS. Tensile tests on the ADC12 foams indicated that as their porosity increased, the tensile strength and tensile strain decreased, with strong relation between the porosity, tensile strength, and tensile strain. ADC12 foams exhibited brittle fracture, whereas ALPORAS exhibited ductile fracture, which is due to the nature of the Al alloy used as the base material of the foams. By image-based finite element (FE analysis using X-ray CT images corresponding to the tensile tests on ADC12 foams, it was shown that the fracture path of ADC12 foams observed in tensile tests and the regions of high stress obtained from FE analysis correspond to each other. Therefore, it is considered that the fracture behavior of ADC12 foams in relation to their pore structure distribution can be investigated by image-based FE analysis.

  10. Comparison of marginal accuracy of castings fabricated by conventional casting technique and accelerated casting technique: an in vitro study.

    Reddy, S Srikanth; Revathi, Kakkirala; Reddy, S Kranthikumar

    2013-01-01

    Conventional casting technique is time consuming when compared to accelerated casting technique. In this study, marginal accuracy of castings fabricated using accelerated and conventional casting technique was compared. 20 wax patterns were fabricated and the marginal discrepancy between the die and patterns were measured using Optical stereomicroscope. Ten wax patterns were used for Conventional casting and the rest for Accelerated casting. A Nickel-Chromium alloy was used for the casting. The castings were measured for marginal discrepancies and compared. Castings fabricated using Conventional casting technique showed less vertical marginal discrepancy than the castings fabricated by Accelerated casting technique. The values were statistically highly significant. Conventional casting technique produced better marginal accuracy when compared to Accelerated casting. The vertical marginal discrepancy produced by the Accelerated casting technique was well within the maximum clinical tolerance limits. Accelerated casting technique can be used to save lab time to fabricate clinical crowns with acceptable vertical marginal discrepancy.

  11. National Metal Casting Research Institute final report. Development of an automated ultrasonic inspection cell for detecting subsurface discontinuities in cast gray iron. Volume 3

    Burningham, J.S. [University of Northern Iowa, Cedar Falls, IA (United States). Dept. of Industrial Technology

    1995-08-01

    This inspection cell consisted of an ultrasonic flaw detector, transducer, robot, immersion tank, computer, and software. Normal beam pulse-echo ultrasonic nondestructive testing, using the developed automated cell, was performed on 17 bosses on each rough casting. Ultrasonic transducer selection, initial inspection criteria, and ultrasonic flow detector (UFD) setup parameters were developed for the gray iron castings used in this study. The software were developed for control of the robot and UFD in real time. The software performed two main tasks: emulating the manual operation of the UFD, and evaluating the ultrasonic signatures for detecting subsurface discontinuities. A random lot of 105 castings were tested; the 100 castings that passed were returned to the manufacturer for machining into finished parts and then inspection. The other 5 castings had one boss each with ultrasonic signatures consistent with subsurface discontinuities. The cell was successful in quantifying the ultrasonic echo signatures for the existence of signature characteristics consistent with Go/NoGo criteria developed from simulated defects. Manual inspection showed that no defects in the areas inspected by the automated cell avoided detection in the 100 castings machined into finished parts. Of the 5 bosses found to have subsurface discontinuities, two were verified by manual inspection. The cell correctly classified 1782 of the 1785 bosses (99.832%) inspected.

  12. Casting thermal simulation

    Shamsuddin bin Sulaiman

    1994-01-01

    The whole of this study is concerned with process simulation in casting processes. This study describes the application of the finite element method as an aid to simulating the thermal design of a high pressure die casting die by analysing the cooling transients in the casting cycle. Two types of investigation were carried out to model the linear and non-linear cooling behavior with consideration of a thermal interface effect. The simulated cooling for different stages were presented in temperature contour form. These illustrate the successful application of the Finite Element Method to model the process and they illustrate the significance of the thermal interface at low pressure

  13. An eco design strategy for high pressure die casting components: microstructural analysis applied to mass reducing processes; Una estrategia de ecodiseno de piezas obtenidas mediante moldeo a presion: analisis microestructrual aplicado a la desmaterializacion

    Suarez-Pena, B.; Asensio-Lozano, J.

    2009-07-01

    In this work the study focused on the possibility of use of new aluminium alloys with optimized microstructures that ensure the mechanical properties requested for cast components made by high pressure die casting. The objective was to check the possibility of manufacture of structurally sound eco-steps for escalators with reduced structural integrity. The former arises as a result of a new redesign of the traditional steps aiming at a significant weight reduction. The experimental results show that it is feasible to cut the use of materials during processing and therefore to reduce the impact of the components during its lifetime, whilst the performance and safety standards are kept identical or even improved. (Author) 17 refs.

  14. A comparative evaluation of the marginal adaptation of a thermoplastic resin, a light cured wax and an inlay casting wax on stone dies: An in vitro study

    Reji P Gopalan

    2018-01-01

    Conclusion: The marginal adaptation of all the three materials used, was well within the acceptable range of 25–70 μm. The resin pattern materials studied revealed significantly less dimensional change than inlay casting wax on storage at 1, 12, and 24 h time intervals. They may be employed in situations where high precision and delayed investing is expected.

  15. Die dogmatiese binding van die prediking

    genoemde probleemstelling wat ons homileties na riglyne wil soek, sonder die pretensie dat finale oplossings gevind sal word. Om hierdie probleem te ontleed is dit nodig om eers kortliks 'n begripsbepaling van die begrippe dogma, binding en prediking te maak. Vanuit die begripsbepaling kan ons dan probeer vasstel wat ...

  16. High-performance ceramic filters for energy engineering. Final report; Filter aus Hochleistungskeramik fuer die Energietechnik. Abschlussbericht

    Westerheide, R. [Fraunhofer-Institut fuer Werkstoffmechanik (IWM), Freiburg im Breisgau (Germany); Adler, J. [Fraunhofer-Institut fuer Keramische Technologien und Sinterwerkstoffe (IKTS), Dresden (Germany); Buhl, H. [ESK-SIC GmbH, Frechen-Grefrath (Germany); Fister, D. [H.C. Starck GmbH, Laufenburg (Germany); Krein, J. [LLB Lurgi Lentjes Energietechnik GmbH, Frankfurt (Germany); Voelker, W. [Annawerk GmbH, Roedental (Germany); Walch, A. [eds.] [USF Schumacher Umwelt- und Trenntechnik GmbH, Crailsheim (Germany)

    1999-09-30

    The hot gas particulate removal of many advanced coal fired power generation technologies works at temperatures above 800 C. The filter elements for these applications are often based on ceramic materials, e.g. silicon carbide. However, the mostly clay bonded silicon carbide is subject to creep and oxidation due to probable changes of the binder phase. In this work the development of new ceramic filter materials based on silicon carbide and alumina is described. The goal of the development was to increase the potential application temperature. To obtain the goal, the work was performed together with ceramic powder manufacturers, developers of ceramic materials and components as well as with companies who operate test facilities. Different routes were chosen to increase the high temperature resistance in consideration of corrosion resistance, fracture strength and pressure loss of the filter materials. One of these routes was the optimization of the binder phase of the silicon carbide materials. Other routes were concentrated on the base material and the investigation of other possibilities for the silicon carbide bonding, i.e. a recrystallization process of SiC (RSiC) or a self bonding of granulated small grained silicon carbide powder. Additionally filter materials based on alumina were developed. The report covers these material development oriented topics as well as the additional work in materials reliability, coating development and modeling of microstructure. (orig.) [German] In der Kombikraftwerkstechnik wird insbesondere bei Kohlefeuerung die Heissgasreinigung oft bei Temperaturen ueber 800 C eingesetzt. Die Filterelemente fuer diese Anwendungen bestehen oft aus keramischen Materialien. Das haeufig eingesetzte tongebundene Siliciumcarbid unterliegt jedoch besonders aufgrund der Beschaffenheit der Bindephase Kriech- und Oxidationsschaedigungen. In diesem Bericht wird die Entwicklung von neuen keramischen Filtermaterialien, die auf Siliciumcarbid oder

  17. die rol van die unieverdedigingsmag in die onderdrukking van die

    agv regeringsoptrede nie.39. Siotsom. In die geskiedenis van die Unieverdedigings- mag word die gebeure random die 1914-staking oorskadu deur die Rebellie en Suid-Afrika se deelname aan die Eerste Wereldoorlog. Tog was dit 'n belangrike mylpaal in die geskiedenis van die organisasie, omdat dit sy eerste optrede ...

  18. Determining casting defects in near-net shape casting aluminum parts by computed tomography

    Li, Jiehua; Oberdorfer, Bernd; Habe, Daniel; Schumacher, Peter

    2018-03-01

    Three types of near-net shape casting aluminum parts were investigated by computed tomography to determine casting defects and evaluate quality. The first, second, and third parts were produced by low-pressure die casting (Al-12Si-0.8Cu-0.5Fe-0.9Mg-0.7Ni-0.2Zn alloy), die casting (A356, Al-7Si-0.3Mg), and semi-solid casting (A356, Al-7Si-0.3Mg), respectively. Unlike die casting (second part), low-pressure die casting (first part) significantly reduced the formation of casting defects (i.e., porosity) due to its smooth filling and solidification under pressure. No significant casting defect was observed in the third part, and this absence of defects indicates that semi-solid casting could produce high-quality near-net shape casting aluminum parts. Moreover, casting defects were mostly distributed along the eutectic grain boundaries. This finding reveals that refinement of eutectic grains is necessary to optimize the distribution of casting defects and reduce their size. This investigation demonstrated that computed tomography is an efficient method to determine casting defects in near-net shape casting aluminum parts.

  19. Fabrication of sacrificial anode cathodic protection through casting method

    Mohd Sharif Sattar; Muhamad Daud; Siti Radiah Mohd Kamarudin; Azali Muhamad; Zaiton Selamat; Rusni Rejab

    2007-01-01

    Aluminum is one of the few metals that can be cast by all of the processes used in casting metals. These processes consist of die casting, permanent mold casting, sand casting (green sand and dry sand), plaster casting, investment casting, and continuous casting. Other processes such as lost foam, squeeze casting, and hot isostatic pressing are also used. Permanent mold casting method was selected in which used for fabricating of sacrificial anode cathodic protection. This product was ground for surface finished and fabricated in the cylindrical form and reinforced with carbon steel at a center of the anode. (Author)

  20. Numerical optimization of die geometry in open die forging

    Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

    2013-01-01

    This paper deals with numerical optimization of open die forging of large metallic ingots made by casting implying risk of defects, e.g. central pores. Different material hardening properties and die geometries are combined in order to investigate, which geometry gives rise to maximum closure...

  1. Die binding van die konfessie

    P. J. Coetzee

    1970-05-01

    Full Text Available Ons moet waak teen twee uiterstes. Aan die een kant het die dogma as onversoenlike vyand die dogmatisme en aan die ander kant die antidogmatisme — dit hou enersyds die gevaar in van verabsolutering (oorskatting, en ander- syds die gevaar van relativisme (onderskatting.

  2. Die Region braucht die Kultur - die Kultur braucht die Region

    Klemm, Ulrich

    1995-01-01

    Die Region braucht die Kultur - die Kultur braucht die Region. - In: Region in Aktion - oder: Region im Abseits? - Boxberg-Wölchingen : Eigenständige Regionalentwicklung Baden-Württemberg, 1995. - S. 25 f.

  3. Clean Metal Casting

    Makhlouf M. Makhlouf; Diran Apelian

    2002-02-05

    The objective of this project is to develop a technology for clean metal processing that is capable of consistently providing a metal cleanliness level that is fit for a given application. The program has five tasks: Development of melt cleanliness assessment technology, development of melt contamination avoidance technology, development of high temperature phase separation technology, establishment of a correlation between the level of melt cleanliness and as cast mechanical properties, and transfer of technology to the industrial sector. Within the context of the first task, WPI has developed a standardized Reduced Pressure Test that has been endorsed by AFS as a recommended practice. In addition, within the context of task1, WPI has developed a melt cleanliness sensor based on the principles of electromagnetic separation. An industrial partner is commercializing the sensor. Within the context of the second task, WPI has developed environmentally friendly fluxes that do not contain fluorine. Within the context of the third task, WPI modeled the process of rotary degassing and verified the model predictions with experimental data. This model may be used to optimize the performance of industrial rotary degassers. Within the context of the fourth task, WPI has correlated the level of melt cleanliness at various foundries, including a sand casting foundry, a permanent mold casting foundry, and a die casting foundry, to the casting process and the resultant mechanical properties. This is useful in tailoring the melt cleansing operations at foundries to the particular casting process and the desired properties of cast components.

  4. Die ontwikkeling van die bestuursmotiveringsvraelys (BMV

    A. S. Engelbrecht

    1991-06-01

    Full Text Available The development of the Managerial Motivation Questionnaire (MMQ: Several criticisms of the psychometric suitability of existing measures of managerial motivation are reported in the literature. This study aimed at developing a new psychometrically sound instrument, the Managerial Motivation Questionnaire (MMQ. This was done on the basis of a comprehensive study of the literature on managerial motivation and the role-motivation theory. The preliminary MMQ was systematically shortened and refined until the final MMQ of 98 items was composed. This was based on social desirability and semantic appraisal, item analysis and factor analysis of the questionnaire. The results indicate that it was possible to develop a final MMQ that was relatively free of social desirability. It further demonstrated satsifactory internal consistencies on two samples (a = 0/90, N = 360; a = 0/91, N = 535, where all subscale items were found to be relatively pure measures of the isolated factors. Although some evidence was found providing support for the reliability of the MMQ, a need for further research on the construct validity of managerial motivation still exists. Opsomming In die literatuur word verskeie punte van kritiek teen die psigometriese geskiktheid van bestaande meetinstrumente van bestuursmotivering gerapporteer. Die doelstelling van hierdie studie was dus om aan die hand van die konseptuele omiyning van bestuursmotivering, en die rolmotiveringsteorie as algemene verwysingsraamwerk, 'n nuwe psigometries aanvaarbare meetinstrument, die Bestuursmotiveringsvraelys (BMV, te ontwikkel. Op grond van sosiale wenslikheids- en semantiese beoordeling, itemontleding en faktorontleding van die voorlopige BMV is die vraelys stelselmatig verkort en verfyn totdat die finale BMV van 98 items saamgestel is. Die resultate dui daarop dat hierdie studie wel daarin geslaag het om 'n finale BMV te ontwikkel wat relatief vry van sosiale wenslikheid is, bevredigende interne

  5. The effect of Fe-rich intermetallics on the microstructure, hardness and tensile properties of Al–Mg2Si die-cast composite

    Emamy, M.; Emami, A.R.; Khorshidi, R.; Ghorbani, M.R.

    2013-01-01

    Highlights: ► Effect of Fe on the microstructure and mechanical properties of Al–Mg 2 Si composite. ► Fe changed the size of primary Mg 2 Si from 33 μm to 15 μm. ► Higher hardness, YS, UTS and Quality Index values obtained from Fe addition. ► Different morphologies of Fe-intermetallics were found with higher Fe contents. - Abstract: In present paper, an attempt was made to examine the effect of different concentrations of Fe (0.5, 1, 1.5, 2 and 3 wt.%) on the microstructure and tensile properties of an in situ Al–15wt.%Mg 2 Si metal matrix composite (MMC). The composite was made by casting process and characterized by optical microscope, scanning electron microscope (SEM) equipped with energy dispersive X-ray spectroscopy. The results depicted that the addition of 2 wt.% Fe to the MMC changes the morphology of primary Mg 2 Si from irregular to polyhedral shape and reduces its average particle size from 33 μm to 15 μm. The microstructural studies also showed that the addition of Fe leads to the formation of Fe-rich intermetallics with polyhedral, plate-like and star-like morphology. Hardness results demonstrated that Fe addition to Al–15%Mg 2 Si composite has a positive effect on the hardness improvement. Further investigations on tensile tests revealed optimum Fe (1 wt.%) level for improving tensile properties. In the point of fracture behavior of the composite, Fe-containing specimens showed a brittle mode of failure

  6. Die nabyheid van die Koninkryk

    W.J. Snyman

    1963-03-01

    Full Text Available Vanweë die belangrikheid daarvan volg hier ’n breër bespreking van die proefskrif van dr. Tjaart van der Walt oor die nabyheid van die Koninkryk as wat in ’n gewone resensie kan geskied. Die vraagstuk wat onder oë gesien word is so oud as die kerk en die teologie, soms minder en soms meer op die voorgrond. Tans kan gesê word, staan dit in die middelpunt. Daarby is dit nie maar ’n akademiese vraagstuk nie, maar ’n vraagstuk waarvoor elke nadenkende leser van die Skrif te staan kom.

  7. ASSESSMENT OF SURFACE FINISH AND DIMENSIONAL ACCURACY OF TOOLS MANUFACTURED BY METAL CASTING IN RAPID PROTOTYPING SAND MOULDS

    Nyembwe, K.

    2012-11-01

    Full Text Available In this paper, an initial assessment of the quality parameters of the surface finish and dimensional accuracy of tools made by metal casting in rapid prototyping (RP sand moulds is undertaken. A case study from a local tool room, dealing with the manufacturing of an aluminium die for the lost wax process, is employed. Modern techniques, including surface roughness analysis and three dimensional scanning, are used to determine and understand how each manufacturing step influences the final quality of the cast tool. The best surface finish obtained for the cast die had arithmetic average roughness (Ra and mean average roughness (Rz respectively equal to 3.23m and 11.38m. In terms of dimensional accuracy, 82% of cast-die points coincided with the Computer Aided Design (CAD data, which is within the typical tolerances of sand cast products. The investigation shows that mould coating contributes slightly to the improvement of the cast tool surface finish. The study also found that the additive manufacturing of the sand mould was the chief factor responsible for the loss of dimensional accuracy. These findings indicate that machining will always be required to improve the surface finish and the dimensional accuracy of cast tools in RP sand moulds.

  8. AN INTRODUCTION TO RAPID CASTING: DEVELOPMENT AND INVESTIGATION OF PROCESS CHAINS FOR SAND CASTING OF FUNCTIONAL PROTOTYPES

    D. Dimitrov

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: This paper discusses the results obtained from studies on different Rapid Tooling process chains in order to improve the design and manufacture of foundry equipment that is used for sand casting of prototypes in final material. These prototypes are intended for functional and pre-production tests of vehicles. The Three Dimensional Printing process is used as core technology. Subsequently, while considering aspects such as time, cost, quality (accuracy and surface roughness, and tool life, a framework is presented for the evaluation and selection of the most suitable process chain in accordance with specific requirements. This research builds on an in-depth characterisation of the accuracy and repeatability of a 3D printing process.

    AFRIKAANSE OPSOMMING: Hierdie artikel bespreek die resultate wat verkry is tydens studies op verskillende Snel-Gereedskapvervaardigingproseskettings wat ondersoek is teneinde die ontwerp en vervaardiging van sandgietgereedskap, om prototipes in finale materiaal te vervaardig, te verbeter. Die prototipes is bestem vir gebruik in funksionele- en voorproduksietoetse van voertuie. Die sogenaamde Driedimensionele Drukproses (3DP is as kerntegnologie aangewend. Gevolglik, na oorweging van aspekte soos tyd, koste, kwaliteit (akkuraatheid en oppervlakafwerking, en gereedskapleeftyd, is ’n raamwerk ontwikkel vir die evaluering en seleksie van die mees geskikte prosesketting met inagname van spesifieke vereistes. Hierdie navorsing bou op ’n diepgaande karakterisering van die akkuraatheids- en herhaalbaarheidsvermoë van ’n 3D drukproses.

  9. Die topkwark

    R. Tegen

    1998-07-01

    Full Text Available ’n Oorsig van die belangrikheid van die onlangs ontdekte topkwark by Fermilab in Chicago word gegee. Daar word aangetnon dat die topkwark belangrik is in fisika van die Oerknal, oftewel "Big Bang", en in die Standaard Model van Elementêredeeltjie-fisika. Toepaslike literatuur vir verdere studie kan van die lys van verwysings in hierdie kort, nietegniese artikel, nagegaan word.

  10. Effect of Starting As-cast Structure on the Microstructure-Texture Evolution During Subsequent Processing and Finally Ridging Behavior of Ferritic Stainless Steel

    Modak, Pranabananda; Patra, Sudipta; Mitra, Rahul; Chakrabarti, Debalay

    2018-06-01

    Effect of the initial as-cast structure on the microstructure-texture evolution during thermomechanical processing of 409L grade ferritic stainless steel was studied. Samples from the regions of cast slab having `columnar,' `equiaxed,' and a mixture of `columnar' and `equiaxed' grains were subjected to two different processing schedules: one with intermediate hot-band annealing before cold-rolling followed by final annealing, and another without any hot-band annealing. EBSD study reveals that large columnar crystals with cube orientation are very difficult to deform and recrystallize uniformly. Resultant variations in ferrite grain structure and retention of cube-textured band in cold-rolled and annealed sheet contribute to ridging behavior during stretch forming. Initial equiaxed grain structure is certainly beneficial to reduce or even eliminate ridging defect by producing uniform ferrite grain structure, free from any texture banding. Application of hot-band annealing treatment is also advantageous as it can maximize the evolution of beneficial gamma-fiber texture and eliminate the ridging defect in case of completely `equiaxed' starting structure. Such treatment reduces the severity of ridging even if the initial structure contains typically mixed `columnar-equiaxed' grains.

  11. Effect of cast steel production metallurgy on the emergence of casting defects

    L. Čamek

    2016-10-01

    Full Text Available The paper documents metallurgical possibilities of high alloy cast steel production in open induction medium frequency furnaces and an electric arc furnace in a gravity die casting foundry. The observation was focused on the emergence of gas defects in steel castings. The content of gases achieved during the metallurgical processes was evaluated for every unit of the production equipment and the casting ladle before casting into disposable sand moulds. The sand mould area was considered to be constant. The aim was to evaluate the current metallurgical possibilities of affecting the content of gases in high alloy cast steel in the current technical conditions of the foundry.

  12. Final Report, Volume 4, The Develpoment of Qualification Standards forCast Super Duplex Stainless Steel (2507 Wrought Equivalent)

    Hariharan, Vasudevan; Lundin, Carl, D.

    2005-09-30

    The objective of the program is to determine the suitability of ASTM A923 Standard Test methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic-Ferritic Stainless Steels for 25 Cr Cast Super Duplex Stainless Steels (ASTM A890-5A). Different tests were carried out on the materials procured from various steel foundries as stated in the ASTM A923. The foundries were designated as Foundry A, B, C and D. All the materials were foundry solution annealed. Materials from Foundry D were solution heat treated at The University of Tennessee also and then they were subjected to heat treatment schedule which was derived from the testing of wrought DSS to establish the A923 specification. This was possible because the material from the same heat was sufficient for conducting the full scope of heat treatment. This was done prior to carrying out various other tests. Charpy samples were machined. The Ferrite content was measured in all the Charpy samples using Feritscope{reg_sign} and ASTM E562 Manual Point Count Method. After the ferrite content was measured the samples were sent to AMC-Vulcan, Inc. in Alabama to conduct the Charpy impact test based on ASTM A923 Test Method B. This was followed by etch testing and corrosion analysis based on ASTM A923 Test Methods A and C respectively at University of Tennessee. Hardness testing using Rockwell B and C was also carried out on these samples. A correlation was derived between all the three test methods and the best method for evaluating the presence of intermetallic in the material was determined. The ferrite content was correlated with the toughness values. Microstructural analysis was carried out on the etch test samples using Scanning Electron Microscopy in order to determine if intermetallic phases were present. The fracture surfaces from Charpy test specimens were also observed under SEM in order to determine the presence of any cracks and whether it was a brittle or a ductile fracture. A correlation

  13. Final Report, Volume 4, The Development of Qualification Standards for Cast Super Duplex Stainless Steel (2507 Wrought Equivalent)

    Hariharan, Vasudevan; Lundin, Carl, W.

    2005-09-30

    The objective of the program is to determine the suitability of ASTM A923 Standard Test methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic-Ferritic Stainless Steels for 25 Cr Cast Super Duplex Stainless Steels (ASTM A890-5A). Different tests were carried out on the materials procured from various steel foundries as stated in the ASTM A923. The foundries were designated as Foundry A, B, C and D. All the materials were foundry solution annealed. Materials from Foundry D were solution heat treated at The University of Tennessee also and then they were subjected to heat treatment schedule which was derived from the testing of wrought DSS to establish the A923 specification. This was possible because the material from the same heat was sufficient for conducting the full scope of heat treatment. This was done prior to carrying out various other tests. Charpy samples were machined. The Ferrite content was measured in all the Charpy samples using Feritscope® and ASTM E562 Manual Point Count Method. After the ferrite content was measured the samples were sent to AMC-Vulcan, Inc. in Alabama to conduct the Charpy impact test based on ASTM A923 Test Method B. This was followed by etch testing and corrosion analysis based on ASTM A923 Test Methods A and C respectively at University of Tennessee. Hardness testing using Rockwell B and C was also carried out on these samples. A correlation was derived between all the three test methods and the best method for evaluating the presence of intermetallic in the material was determined. The ferrite content was correlated with the toughness values. Microstructural analysis was carried out on the etch test samples using Scanning Electron Microscopy in order to determine if intermetallic phases were present. The fracture surfaces from Charpy test specimens were also observed under SEM in order to determine the presence of any cracks and whether it was a brittle or a ductile fracture. A correlation was

  14. Impact properties of zinc die cast alloys

    Schrems, Karol K.; Dogan, Omer N.; Manahan, M.P. (MPM Technologies, Inc.); Goodwin, F.E. (ILZRO)

    2005-01-01

    Alloys 3, 5, AcuZinc 5, and ZA-8 were tested at five temperatures between -40 C and room temperature to determine impact properties. Izod impact energy data was obtained in accordance with ASTM D256. Unlike ASTM E23, these samples were tested with a milled notch in order to compare with plastic samples. In addition, flexural data was obtained for design use.

  15. Monitoring as component for the decision making in final repository projects; Monitoring als Baustein fuer die Entscheidungsfindung in Endlagerprojekten

    Kallenbach-Herbert, Beate; Alt, Stefan [Oeko-Institut e.V., Darmstadt (Germany)

    2012-12-15

    The monitoring in final radioactive waste repositories is performed by continuous or repeated measurements of technical and geologic parameters during long time periods. The collected data serve manifold purposes. The central focus is to provide fundamental information for the decision between and within the three phases of a final repository project. This means that monitoring is not only the sum of technical surveillance measures. Monitoring is also important for several sociopolitical decisions, for instance in case of closure of the repository. The article discusses possible objectives and shows the relevant technical aspects that are used deduce the requirements for an integrated monitoring concept. It is shown that a monitoring concept should be developed early enough involving all groups that are concerned by the waste disposal project.

  16. HFIR Fuel Casting Support

    Imhoff, Seth D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gibbs, Paul Jacob [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Solis, Eunice Martinez [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-09-28

    Process exploration for fuel production for the High Flux Isotope Reactor (HFIR) using cast LEU-10wt.%Mo as an initial processing step has just begun. This project represents the first trials concerned with casting design and quality. The studies carried out over the course of this year and information contained in this report address the initial mold development to be used as a starting point for future operations. In broad terms, the final billet design is that of a solid rolling blank with an irregular octagonal cross section. The work covered here is a comprehensive view of the initial attempts to produce a sound casting. This report covers the efforts to simulate, predict, cast, inspect, and revise the initial mold design.

  17. Caste System

    Hoff, Karla

    2016-01-01

    In standard economics, individuals are rational actors and economic forces undermine institutions that impose large inefficiencies. The persistence of the caste system is evidence of the need for psychologically more realistic models of decision-making in economics. The caste system divides South Asian society into hereditary groups whose lowest ranks are represented as innately polluted. ...

  18. Die funksie van die belydenis in die struktuur van die kerk en die ...

    Ter wille van die argument wat in hierdie voordrag na vore gebring word, word vier sodanige konstituerende elemente van die kerklike struktuur onderskei, te wete die belydenis, die teologie, die verkondi- ging (meer bepaald die prediking) en die kerkorde (kerkwet volgens ons terminologie). Ons gaan nou elkeen hiervan ...

  19. Results obtained so far with the production of turbine and valve casings made of the new 9% Cr cast steel types G-X 12 CrMoWVNbN 10 11 and G-X 12 CrMoVNbN 91; Erfahrungsbericht ueber die Herstellung von Turbinen- und Ventilgehaeusen aus den neuen 9% Cr-Stahlgusssorten G-X 12 CrMoWVNbN 10 1 1 und G-X 12 CrMoVNbN 91

    Schuster, F.; Buberl, A.; Hanus, R. [VOEST-ALPINE STAHL LINZ GmbH, Linz (Austria); Cerjak, H. [Technische Univ., Graz (Austria)

    1996-12-31

    In the course of production start-up of new 9-10% Cr cast steel types, and application of R and D results to practice, the following examinations and modifications have been performed: 1. Reduction of average chromium content from 10.5 to 9.5% in order to suppress delta ferrite segregation, and adjustment of austenite and ferrite stabilizing alloying constituents. 2. Analysis of typical defects in castings, and modification of casting and feeding techniques in compliance with the saturation behaviour of the new 9-10% Cr steels. These measures achieved a reduction of feeding-based flaws (shrinkage) in the last few cast pieces. 3. The good weldability was proven of the new 9-10% Cr steels by means of welding tests and crack-free production and construction welds made in cast pieces. (orig./MM) [Deutsch] Im Zuge der Produktionsaufnahme neuer 9-10% Cr-Stahlgusssorten und der Ueberleitung der F and E Ergebnisse in die betriebliche Praxis wurden folgende Untersuchungen und Anpassungen vorgenommen: 1. Um die Deltaferritausscheidung zu unterdruecken, wurde der mittlere Chromgehalt von 10,5 auf 9,5% abgesenkt und die austenit- und ferritstabilisierenden Legierungselemente besser angepasst. 2. Die Analyse typischer Fehlererscheinungen an Gussstuecken machten eine Anpassung der Giess- und Speisungstechnik an das Saettigungsverhalten der neuen 9-10% Cr-Staehle erforderlich. Diese Massnahmen fuehrten zu einer Verringerung der Speisungsfehler (Lunker) bei den zuletzt abgegossenen Gussstuecken. 3. Bei Schweissversuchen und an Gussstuecken rissfrei ausgefuehrten Fertigungs- und Konstruktionsschweissungen konnte die gute Schweisseignung der neuen 9-10% Cr-Staehle nachgewiesen werden. (orig./MM)

  20. Fracture Mechanisms in Steel Castings

    Stradomski Z.

    2013-09-01

    Full Text Available The investigations were inspired with the problem of cracking of steel castings during the production process. A single mechanism of decohesion - the intergranular one - occurs in the case of hot cracking, while a variety of structural factors is decisive for hot cracking initiation, depending on chemical composition of the cast steel. The low-carbon and low-alloyed steel castings crack due to the presence of the type II sulphides, the cause of cracking of the high-carbon tool cast steels is the net of secondary cementite and/or ledeburite precipitated along the boundaries of solidified grains. Also the brittle phosphor and carbide eutectics precipitated in the final stage solidification are responsible for cracking of castings made of Hadfield steel. The examination of mechanical properties at 1050°C revealed low or very low strength of high-carbon cast steels.

  1. Die posisie van die Helper in die sending

    I. J. van der Walt

    1972-05-01

    Full Text Available Gedurende die aanvangsjare van die sending het die helper ’n onmisbare funksie vervul. Hulle het die onherbergsame binnelande geken, waardevolle kontakpunte vir die sendelinge geopen en hulle mense geestelik help voorlig en voorberei.

  2. Hair casts

    Sweta S Parmar; Kirti S Parmar; Bela J Shah

    2014-01-01

    Hair casts or pseudonits are circumferential concretions, which cover the hair shaft in such a way that, it could be easily removed. They are thin, cylindrical, and elongated in length. We present an unusual case of an 8-year-old girl presenting with hair casts. Occurrence of these is unusual, and they may have varied associations. This patient was suffering from developmental delay. It is commonly misdiagnosed as and very important to differentiate from pediculosis capitis.

  3. Influence of casting conditions on durability and structural performance of HPC-AR : optimization of self-consolidating concrete to guarantee homogeneity during casting of long structural elements : final report.

    2017-05-01

    This report is a summary of the research done on dynamic segregation of self-consolidating concrete (SCC) including the casting of pre-stressed beams at Coreslab Structures. SCC is a highly flowable concrete that spreads into place with little to no ...

  4. DIE GESKIEDENIS VAN DIE PERSONEELFUNKSIE IN DIE SA ...

    stel (kortdiensstelsel). Met die uitbreek van die oorlog in 1939 het die. Unieverdedigingsmag uit 40% Staandemag en. 60% aktiewe Burgermag bestaan. Op 22 Sept. 1939 is magtiging aan die Aktiewe Burgermag- eenhede verleen om vrywilligers vir die duur van die oorlog te aanvaar. Agv beswaar dat die Verdedigingswet.

  5. Die Formatestadt

    Günter Trojan

    2013-01-01

    Zu Zeiten von DV oder VHS (wer kennt das eigentlich noch?) war die Welt noch in Ordnung: Da hatte man eine Kassette in der Hand und wenn das passende Gerät gefunden wurde konnte man das Video auch abspielen. Günter Trojan diskutiert die Geschichte und Gegenwart unterschiedlicher Videoformate ...

  6. Die Formatestadt

    Günter Trojan

    2013-06-01

    Full Text Available Zu Zeiten von DV oder VHS (wer kennt das eigentlich noch? war die Welt noch in Ordnung: Da hatte man eine Kassette in der Hand und wenn das passende Gerät gefunden wurde konnte man das Video auch abspielen. Günter Trojan diskutiert die Geschichte und Gegenwart unterschiedlicher Videoformate ...

  7. Effects of forming temperature and sintering rate to the final properties of FeCuAl powder compacts formed through uniaxial die compaction process

    Rahman, M. M.; Ismail, M. A.; Sopyan, I.; Rahman, H. Y.

    2018-01-01

    This paper presents the outcomes of an experimental investigation on the effects of forming temperature and sintering schedule to the final characteristics of FeCuAl powder mass formed at different temperature and sintered at different schedule. A lab-scale uni-axial die compaction rig was designed and fabricated which enabled the compaction of powder mass at room temperature as well as elevated temperature. Iron (Fe) powder ASC 100.29 was mechanically mixed with other elemental powders, namely copper (Cu), and aluminum (Al) for 60 minutes and compacted at three different temperature, i.e., 30°C, 150°C, and 200°C by applying 425 MPa of simultaneous downward and upward axial loading to generate green compacts. The as-pressed samples were inspected visually and the defect-free green compacts were subsequently sintered in an argon gas fired furnace at 800°C for 60 min at three different heating/cooling rates, i.e., 5, 10, and 15°C/min, respectively. The sintered samples were then characterised for their physical, electrical, and mechanical properties. The microstructures of the sintered samples were also analysed. The results revealed that a forming temperature of 150°C and a sintering rate of 10°C/min could produce a product with better characteristics.

  8. Marginal Accuracy of Castings Fabricated with Ringless Casting Investment System and Metal Ring Casting Investment System: A Comparative Study.

    Kalavathi, M; Sachin, Bhuvana; Prasanna, B G; Shreeharsha, T V; Praveen, B; Ragher, Mallikarjuna

    2016-02-01

    The thermal expansion of the investment can be restricted by the metal casting ring because the thermal expansion of the ring is less than that of the investment. The ringless casting procedure is in use in clinical dentistry, though there is little scientific data to support its use in fixed partial dentures. In this study, marginal discrepancy of castings produced with the ringless casting technique and the conventional technique using the metal rings were compared. A total of 30 wax patterns were fabricated directly on a metal die. Optical stereomicroscope was used to measure the marginal discrepancy between the metal die and wax patterns. A total of 15 castings were invested using Bellavest T phosphate-bonded investment with the ringless technique and 15 were invested with the same investment with a metal ring; 30 castings were produced using a nickel-chromium ceramo-metal alloy. The internal surface of the castings was not modified and seated with finger pressure. The vertical marginal discrepancy was measured using an optical stereomicroscope at a magnification of 100x. The data obtained were statistically analyzed using students t-test (paired t-test and unpaired t-test). The castings of the ringless technique provided less vertical marginal discrepancy (240.56 ± 45.81 μ) than the castings produced with the conventional metal ring technique (281.98± 53.05 μ). The difference was statistically significant. The ringless casting technique had produced better marginal accuracy compared with conventional casting technique. Ringless casting system can be used routinely for clinical purpose.

  9. Rapid die manufacturing using direct laser metal deposition

    Pereira, MFVT

    2009-01-01

    Full Text Available This paper highlights the work undertaken at the CSIR on the issue of rapid die manufacturing through the application and evaluation of a rapid prototyping technique and coating technologies applied to die components of a high pressure casting die...

  10. Hydrogen analysis and effect of filtration on final quality of castings from aluminium alloy AlSi7Mg0,3

    M. Brůna

    2011-01-01

    Full Text Available The usage of aluminium and its alloys have increased in many applications and industries over the decades. The automotive industry is the largest market for aluminium castings and cast products. Aluminium is widely used in other applications such as aerospace, marine engines and structures. Parts of small appliances, hand tools and other machinery also use thousands of different aluminium castings. The applications grow as industry seeks new ways to save weight and improve performance and recycling of metals has become an essential part of a sustainable industrial society. The process of recycling has therefore grown to be of great importance, also another aspect has become of critical importance: the achievement of quality and reliability of the products and so is very important to underst and the mechanisms of the formation of defects in aluminium melts, and also to have a reliable and simple means of detection.

  11. CASTING FURNACES

    Ruppel, R.H.; Winters, C.E.

    1961-01-01

    A device is described for casting uranium which comprises a crucible, a rotatable table holding a plurality of molds, and a shell around both the crucible and the table. The bottom of the crucible has an eccentrically arranged pouring hole aligned with one of the molds at a time. The shell can be connected with a vacuum.

  12. Power transmission in combined compressors comprising a radial and side channel stage. Final report and appendices; Untersuchungen ueber die Energieuebertragung in kombinierten Verdichtern aus Radial- und Seitenkanalstufe. Abschlussbericht und Anlagen

    Surek, D.

    2001-07-30

    In the field of turbo-compressors, the following problems must be solved in order to extend the range of operation: (a) Prevention of rotating stall at part load; (b) Extension of the permissible operating range at part load; (c) Extension of the operation range of radial and side channel compressors in higher vacuum below p{sub s}=50kPa. (c) can be achieved by changing the flow pattern in the rotor and in the region of interaction between the blade wheel and guide wheel of radial compressors or by actively influencing transient flow, e.g. by coupling radial compressor stages with a side channel compressor stage as final stage. The contribution goes into detail about the latter solution. [German] Fuer den Turboverdichterbau sind gegenwaertig folgende Probleme zur Erweiterung der Betriebsbereiche dringend zu loesen: (a) Vermeiden oder beseitigen von Rotating Stall im Teillastbereich,(b) Erweiterung des zulaessigen Arbeitsbereiches im Teillastgebiet, (c) Erschliessung des Arbeitsbereichs von Radial- und Seitenkanalverdichtern im hoeheren Vakuumbereich unterhalb von p{sub s}=50 kPa. Die Erweiterung des zulaessigen Arbeitsbereichs im Teillastgebiet kann durch Veraenderung der Stroemungsstruktur im Laufrad und im Interaktionsbereich zwischen Lauf- und Leitrad von Radialverdichtern oder durch die aktive Beeinflussung der instationaeren Stroemung z.B. durch Kopplung von Radialverdichterstufen mit einer Seitenkanalverdichterstufe als Endstufe erfolgen. Seitenkanalverdichter verfuegen ueber stabile Kennlinien im gesamten Betriebsbereich. Im Kombinationsbetrieb einer Radialverdichterstufe mit nach- oder vorgeschalteter Seitenkanalverdichterstufe praegte die Seitenkanalverdichterstufe dem Kombinationsverdichter ihr stabiles Kennlinienverhalten auf, so dass sich eine stabile Gesamtkennlinie ergibt. Eine Pumpgrenze tritt nicht mehr auf, so dass der Betrieb von Verdichterkombinationen aus Radial- und Seitenkanalstufe im gesamten Kennlinienbereich moeglich ist. Die

  13. A National Assistance Extension Program for Metal Casting: a foundation industry. Final report for the period February 16, 1994 through May 15, 1997

    NONE

    1997-09-01

    The TRP award was proposed as an umbrella project to build infrastructure and extract lessons about providing extension-enabling services to the metal casting industry through the national network of Manufacturing Technology Center`s (MTC`s). It targeted four discrete task areas required for the MCC to service the contemplated needs of industry, and in which the MCC had secured substantial involvement of partner organizations. Task areas identified included Counter-Gravitational Casting, Synchronous Manufacturing, Technology Deployment, and Facility and Laboratory Improvements. Each of the task areas includes specific subtasks which are described.

  14. Die funksie van die skeppingstradisie in die boek Jeremia

    gedeeites voor wat sterk ooreenkomste toon met die beskrywings van die skep pingsgebeure in die boek Jeremia. • Volgpns Von Rad (1957:144-146) het daar wel 'n groep bestaan wat belange ge- had liet by die oorlewering van die skeppingstradisies. Dit was waarskynlik die. Sadokitiese priesters wat om twee redes aan ...

  15. Die regsposisie van die gemolesteerde kind 1

    P.J. Schabort

    1991-03-01

    Full Text Available Hoe reik die reg uit na die seksueel gemolesteerde kind? As na die reg in wye verband gekyk word, sou dit alie wetgewing en alle gemeneregsbeginsels en alle regsprosedures insluit waardeur die Staat poog om molestering te voorkom en die gemolesteerde kind in beskerming te neem. Dit le baie wyd en sou byvoorbeeld die maatreels insluit van die Kindenvet 33 van 1960; die Wet op Egskeiding 70 van 1979; die Wet op Kindersorg 74 van 1983; die Wet op die Status van Kinders 82 van 1987 en die Wet op Bemiddeling in Sekere Egskeidingsaangeleenthede 24 van 1987. Eersdaags sal dit moontlik ook ’n Manifes vir die Regte van Kinders insluit wat vermoedelik geskoei sal wees op die W O se Konvensie vir die Regte van die Kind (1989 w a arv an die RSA tan s nog nie ’n ondertekenaar is nie.

  16. Titanium Aluminide Casting Technology Development

    Bünck, Matthias; Stoyanov, Todor; Schievenbusch, Jan; Michels, Heiner; Gußfeld, Alexander

    2017-12-01

    Titanium aluminide alloys have been successfully introduced into civil aircraft engine technology in recent years, and a significant order volume increase is expected in the near future. Due to its beneficial buy-to-fly ratio, investment casting bears the highest potential for cost reduction of all competing production technologies for TiAl-LPTB. However, highest mechanical properties can be achieved by TiAl forging. In view of this, Access e.V. has developed technologies for the production of TiAl investment cast parts and TiAl die cast billets for forging purposes. While these parts meet the highest requirements, establishing series production and further optimizing resource and economic efficiency are present challenges. In order to meet these goals, Access has recently been certified according to aircraft standards, aiming at qualifying parts for production on technology readiness level 6. The present work gives an overview of the phases of development and certification.

  17. ASSESSMENT OF SURFACE FINISH AND DIMENSIONAL ACCURACY OF TOOLS MANUFACTURED BY METAL CASTING IN RAPID PROTOTYPING SAND MOULDS

    Nyembwe, K.; De Beer, D. J.; Van der Walt, J. G.; Bhero, S.

    2012-01-01

    In this paper, an initial assessment of the quality parameters of the surface finish and dimensional accuracy of tools made by metal casting in rapid prototyping (RP) sand moulds is undertaken. A case study from a local tool room, dealing with the manufacturing of an aluminium die for the lost wax process, is employed. Modern techniques, including surface roughness analysis and three dimensional scanning, are used to determine and understand how each manufacturing step influences the final qu...

  18. Casting methods

    Marsden, Kenneth C.; Meyer, Mitchell K.; Grover, Blair K.; Fielding, Randall S.; Wolfensberger, Billy W.

    2012-12-18

    A casting device includes a covered crucible having a top opening and a bottom orifice, a lid covering the top opening, a stopper rod sealing the bottom orifice, and a reusable mold having at least one chamber, a top end of the chamber being open to and positioned below the bottom orifice and a vacuum tap into the chamber being below the top end of the chamber. A casting method includes charging a crucible with a solid material and covering the crucible, heating the crucible, melting the material, evacuating a chamber of a mold to less than 1 atm absolute through a vacuum tap into the chamber, draining the melted material into the evacuated chamber, solidifying the material in the chamber, and removing the solidified material from the chamber without damaging the chamber.

  19. CASTING APPARATUS

    Gray, C.F.; Thompson, R.H.

    1958-09-23

    An apparatus is described for casting small quantities of uranlum. It consists of a crucible having a hole in the bottom with a mold positioned below. A vertical rcd passes through the hole in the crucible and has at its upper end a piercing head adapted to break the oxide skin encasing a molten uranium body. An air tight cylinder surrounds the crucible and mold, and is arranged to be evacuated.

  20. Nodular cast iron and casting monitoring

    S. Pietrowski

    2008-10-01

    Full Text Available In this paper quality monitoring of nodular cast iron and casting made of it is presented. A control system of initial liquid cast iron to spheroidization, after spheroidization and inoculation with using of TDA method was shown. An application of an ultrasonic method to assessment of the graphite form and the metal matrix microstructure of castings was investigated.

  1. Assisted Dying in Canada.

    Schuklenk, Udo

    This paper makes an affirmative ethical case in favour of the decriminalization of assisted dying in Canada. It then proceeds to defending the affirmative case against various slippery-slope arguments that are typically deployed by opponents of assisted dying. Finally, a recent case of questionable professional conduct by anti-euthanasia campaigners cum academics is flagged as a warning to all of us not to permit the quality of the professional debate to deteriorate unacceptably, despite the personal emotional investments involved on all sides of the debate.

  2. Casting materials

    Chaudhry, Anil R [Xenia, OH; Dzugan, Robert [Cincinnati, OH; Harrington, Richard M [Cincinnati, OH; Neece, Faurice D [Lyndurst, OH; Singh, Nipendra P [Pepper Pike, OH

    2011-06-14

    A foam material comprises a liquid polymer and a liquid isocyanate which is mixed to make a solution that is poured, injected or otherwise deposited into a corresponding mold. A reaction from the mixture of the liquid polymer and liquid isocyanate inside the mold forms a thermally collapsible foam structure having a shape that corresponds to the inside surface configuration of the mold and a skin that is continuous and unbroken. Once the reaction is complete, the foam pattern is removed from the mold and may be used as a pattern in any number of conventional casting processes.

  3. Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Mechanical Performance of Dies

    R. Allen Miller, Principal Investigator; Kabiri-Bamoradian, Contributors: Khalil; Delgado-Garza, Abelardo; Murugesan, Karthik; Ragab, Adham

    2011-09-13

    provided to NADCA for distribution to the industry. Power law based meta-models for predicting machine tie bar loading and for predicting maximum parting surface separation were successfully developed and tested against simulation results for a wide range of machines and experimental data. The models proved to be remarkably accurate, certainly well within the requirements for practical application. In addition to making die structural modeling more accessible, the work advanced the state-of-the-art by developing improved modeling of cavity pressure effects, which is typically modeled as a hydrostatic boundary condition, and performing a systematic analysis of the influence of ejector die design variables on die deflection and parting plane separation. This cavity pressure modeling objective met with less than complete success due to the limits of current finite element based fluid structure interaction analysis methods, but an improved representation of the casting/die interface was accomplished using a combination of solid and shell elements in the finite element model. This approximation enabled good prediction of final part distortion verified with a comprehensive evaluation of the dimensions of test castings produced with a design experiment. An extra deliverable of the experimental work was development of high temperature mechanical properties for the A380 die casting alloy. The ejector side design objective was met and the results were incorporated into the metamodels described above. This new technology was predicted to result in an average energy savings of 2.03 trillion BTU's/year over a 10 year period. Current (2011) annual energy saving estimates over a ten year period, based on commercial introduction in 2009, a market penetration of 70% by 2014 is 4.26 trillion BTU's/year by 2019. Along with these energy savings, reduction of scrap and improvement in casting yield will result in a reduction of the environmental emissions associated with the melting

  4. Die rol van die blanke werker in die motivering van die swart werker

    G. J. Oosthuizen

    1980-11-01

    Opsomming Die motivering van die Swart werker kan nie in die huidige situasie in isolasie bestudeer word nie, omdat die Blanke werker steeds in die bestuursposisie is en daarom die motivering van die Swart werker kan beïnvloed. Hierdie ondersoek was daarop gerig om die rol van die Blanke werker in die motivering van die Swart werker nader te ondersoek. Die houding en die leierskapsbenadering van die Blanke werker teenoor die Swart werker is gemeet, asook die behoeftes wat volgens die Blanke werker by die Swart werker bestaan, bevredig is, of nie bestaan nie. Die behoeftes van Swart werkers, soos deur hulleself gesien, is ook ondersoek. Ten opsigte van sekere aspekte is beduidende verskille gevind.

  5. 2D geometric morphometric analysis casts doubt on the validity of large tanged points as cultural markers in the European Final Palaeolithic

    Serwatka, Kamil; Riede, Felix

    2016-01-01

    directeurs, especially in northern Europe. The vast majority of these finds are from the surface or derive from less-than-secure contexts. Several recent papers have cast doubt on the validity of this artefact class as a taxonomically sensitive marker. Here, we further investigate this issue using 2D...... arch-backed points. Their presence in later assemblages and technocomplexes such as the Brommean cannot therefore be considered as a derived or diagnostic feature. We suggest that this artefact class should rather be linked to weapon systems function (dart-points) different from the coeval arch...

  6. Casting the Spirit: A Handmade Legacy

    Rutenberg, Mona

    2008-01-01

    This article discusses how an art therapist working in a hospital palliative care unit has incorporated a ritual of hand casting to help bring closure to dying patients and family members who are grieving as death approaches. The finished hand sculptures depict the hands of the patients and, sometimes, of their loved ones. They are faithful and…

  7. Feasibility study for new ecolabels for the product group: Wood pellet firings. Final report; Machbarkeitsstudie fuer neue Umweltzeichen fuer die Produktgruppe: Holzpelletfeuerungen. Endbericht

    Hoffmann, E.; Weiss, J.; Hirschl, B.

    2002-07-01

    This assessment is a feasibility study according to ISO 14024. It deals with the question whether an ecolabel is suitable for wood pellet heating systems and how concrete criteria for an ecolabel for wood pellet heating plants could be specified. The study begins with a comprehensive market analysis in order to identify possible plants for which an ecolabel would make sense. In the main part of the study, the environmental relevance of the chosen plants is analysed. For this analysis, plant manufacturers were interviewed and a comparison between wood pellet heating systems and heating systems which use gas, oil or wood was carried out. On the basis of this analysis, it was possible to derive a number of criteria which were discussed with company representatives and other experts in this field. As a result of this dialogue and the investigation process as a whole, the introduction of an ecolabel for wood pellet heating plants can be recommended. Wood pellet heating systems are characterized by their high level of automatation and the use of standardized fuels with constant high quality. Thus, they reach high combustion quality with low emission rates, and risks of misuse are minimized. They may contribute to the increased use of renewable energies and thereby to the achievement of climate protection goals. The proposed certification principles comprise requirements regarding (a) the efficient energy use (efficiency factor under partial load and nominal load, plant's supplementary energy consumption), (b) emission values for CO, NO{sub x}, dust and organic substances, (c) the offer of additional services, as well as (d) requirements with regard to the operating instructions. The transcription of the label is proposed as 'Ecolabel.. because low emission and energy-efficient'. (orig.) [German] Beim vorliegenden Gutachten handelt es sich um eine Machbarkeitsstudie nach ISO 14024. Es behandelt die Frage, ob ein Umweltzeichen fuer Holzpelletfeuerungen

  8. Project study for the final disposal of high-level radioactive wastes in deep-lying geological formations and for intermediate storage. Projektstudie fuer die Endlagerung von hochaktiven Abfaellen in tiefliegenden geologischen Formationen sowie fuer die Zwischenlagerung

    1980-12-01

    The present report has been written to show the feasibility of construction and the operational suitability of different intermediate and final storage concepts for high-level radioactive wastes. It summarizes the information from a project study given under contract by Nagra. The report should orient a broader public about the possible construction of such intermediate and final repositories. The work presented here refers to radioactive wastes which need an extremely long isolation time. Important information from a separate study concerning different aspects of the drilling of deep boreholes, has been integrated into the present report.

  9. Cast irons

    1996-01-01

    Cast iron offers the design engineer a low-cost, high-strength material that can be easily melted and poured into a wide variety of useful, and sometimes complex, shapes. This latest handbook from ASM covers the entire spectrum of one of the most widely used and versatile of all engineered materials. The reader will find the basic, but vital, information on metallurgy, solidification characteristics, and properties. Extensive reviews are presented on the low-alloy gray, ductile, compacted graphite, and malleable irons. New and expanded material has been added covering high-alloy white irons used for abrasion resistance and high-alloy graphitic irons for heat and corrosion resistance. Also discussed are melting furnaces and foundry practices such as melting, inoculation, alloying, pouring, gating and rising, and molding. Heat treating practices including stress relieving, annealing, normalizing, hardening and tempering, autempering (of ductile irons), and surface-hardening treatments are covered, too. ASM Spec...

  10. Die hervertolking van die paradigma in verband met die ...

    Kerkorde van De Mist en die Algemene Reglement van 1816, wat onderskeidelik vir die Kaapse Kerk en die .... Een van die eerstes was Sam Freiherr von Pufendorf (1632-1694) wat in sy werk De habitu religionis ..... Koning was weer aan bewind (vgl Diepenhorst sj:74w; De Visser 1926/1927 lll:202w). 43.1 JD Janssen ...

  11. die heidelbergse kategismus en die kategesemateriaal van die ned

    subjek, objek, leerstof en die metodiek van die senior kategese. Bloemfontein: Algemene Jeugkommissie Sondagskoolboekhandel. de rAAd oer ned ger kerken in Zuid AfrikA. 1921. De zevende vergadering: handelinge. 1925. De negende vergadering: handelinge. de villierS, d. W. 1957. Die Kategese in die Ned. Geref.

  12. die sinodale verband van die nederduitse gereformeerde kerk in die

    Liezel

    Strauss. Die sinodale verband van die Nederduitse Gereformeerde Kerk. 122 die Vrystaatse Sinode anti-veranderingsgesind of eerder gesond-behoudend of gereformeerd-gematig? Veral as dit .... howe) in moeilike omstandighede gebring is (NG Kerk in die OVS 1865-1912:5). In 'n brief op 8 Augustus 1864 ontken Ds.

  13. Die kerkregtelike posisie van die ouderling en diaken in die ...

    ... drie dekades die Kerkreg gevestig as 'n selfstandige vak in die teologiese curriculum, maar ook 'n baie groot rol gespeel daarin dat die beginsels van die kerk like reg beter begryp word. Naas sy wetenskaplike bydrae word met eweveel genoegdoening gedink aan sy bcsondere persoonlikheid, sy werkvermoe, sy humor-.

  14. uniform van die staatspresidentswag - herkoms en tradisie

    A blue uniform was inter alia proposed in 1980 but finally rejected by the Prime Minister in 1984. Instructions were issued to put forth new ideas. All the arguments in ..... In 1896 Is die rang van kommandant van die Staatsartlllerie verhoog tot die van lultenant-kolonel. Henning Pretorlus, father and first commandant of the.

  15. Microstructures and mechanical properties of squeeze cast Al–5.0Cu–0.6Mn alloys with different Fe content

    Zhang, WeiWen; Lin, Bo; Zhang, DaTong; Li, YuanYuan

    2013-01-01

    Highlights: • The effect of Fe-rich phases on squeeze cast Al–Cu alloys with high Fe content. • Four kinds of Fe-rich phases may present in Al–Cu alloys. • There is great tolerance to Fe impurities in squeeze cast Al–Cu alloys. - Abstract: The microstructures and mechanical properties of gravity die cast and squeeze cast Al–5.0 wt% Cu–0.6 wt% Mn alloys with different Fe content have been studied using tensile test, optical microscope, scanning electron microscope, electron probe micro-analyzer and image analysis. The results show that four kinds of Fe-rich intermetallics may present in the final microstructures of the alloys: Chinese script α-Fe (Al 15 (FeMn) 3 (CuSi) 2 ) and Al 6 (FeMn), needle-like β-Fe(Al 7 Cu 2 Fe) and Al 3 (FeMn) when the Fe content increases from 0.1 wt% to 1.5 wt%. In the gravity die cast alloy with 0.5 wt% Fe, the Chinese script α-Fe presents as the main Fe-rich intermetallics, and a few needle-like β-Fe also exist. When the Fe content increases to 1.0 wt%, the main Fe-rich intermetallics change to needle-like Al 3 (FeMn) and Chinese-script Al 6 (FeMn). The needle-like β-Fe disappears when the Fe content is 0.5 wt% in the squeeze cast alloy with an applied pressure of 75 MPa. Furthermore, the secondary dendritic arm spacing of α(Al), the percentage of porosity and the volume fraction of the second intermetallics decrease distinctly in the squeeze cast alloy compared to the gravity die cast alloy. There is a peak value of ultimate strength and yield strength for the alloy with 0.5 wt% Fe. The elongations of the alloys decrease gradually with increasing Fe content and the elongation of the squeeze cast alloys is two times more than that of the gravity die cast alloys

  16. The anti NPP movement in change. New challenges due to the search for a final repository for high-level radioactive waste; Die Anti-AKW-Bewegung im Wandel. Neue Herausforderungen durch die Endlagersuche fuer hochradioaktive Abfaelle

    Brunnengraeber, Achim [Freie Univ. Berlin (Germany). Fachbereich Politik- und Sozialwissenschaften; Freie Univ. Berlin (Germany). Forschungszentrum fuer Umweltpolitik (FFU)

    2013-07-01

    The German Bundestag has decided on June 28th, 2013 the law on the site selection (StandAG) has been enacted as ''national consensus'' for ''social peace''. The compromise is considered to solve the polarized conflict with respect to the site for an final repository for high-level radioactive waste. New challenges result for the government and the civil society.

  17. Riglyne vir die onderwys.

    J. L. du Plooy

    1960-03-01

    Full Text Available In die afgelope vyftig jaar sedert die Unie tot stand gekom het, is veel op die gebied van onderwys tot stand gebring. Dit is heel natuurlik dat ’n mens sou vra: Wat van die toekoms?

  18. Squeeze casting of aluminum alloy A380: Microstructure and tensile behavior

    Li Fang

    2015-09-01

    Full Text Available A380 alloy with a relatively thick cross-section of 25 mm was squeeze cast using a hydraulic press with an applied pressure of 90 MPa. Microstructure and tensile properties of the squeeze cast A380 were characterized and evaluated in comparison with the die cast counterpart. Results show that the squeeze cast A380 possesses a porosity level much lower than the die cast alloy, which is disclosed by both optical microscopy and the density measurement technique. The results of tensile testing indicate the improved tensile properties, specifically ultimate tensile strength (UTS: 215.9 MPa and elongation (Ef: 5.4%, for the squeeze cast samples over those of the conventional high-pressure die cast part (UTS: 173.7 MPa, Ef: 1.0%. The analysis of tensile behavior shows that the squeeze cast A380 exhibits a high tensile toughness (8.5 MJ·m-3 and resilience (179.3 kJ·m-3 compared with the die cast alloy (toughness: 1.4 MJ·m-3, resilience: 140.6 kJ·m-3, despite that, during the onset of plastic deformation, the strain-hardening rate of the die cast specimen is higher than that of the squeeze cast specimens. The microstructure analyzed by the scanning electron microscopy (SEM shows that both the squeeze and die cast specimens contain the primary α-Al, Al2Cu, Al5FeSi phase and the eutectic Si phase. But, the Al2Cu phase present in the squeeze cast alloy is relatively large in size and quantity. The SEM fractography evidently reveals the ductile fracture features of the squeeze cast A380 alloy.

  19. Fibreglass Total Contact Casting, Removable Cast Walkers, and Irremovable Cast Walkers to Treat Diabetic Neuropathic Foot Ulcers: A Health Technology Assessment

    Costa, Vania; Tu, Hong Anh; Wells, David; Weir, Mark; Holubowich, Corinne; Walter, Melissa

    2017-01-01

    Background Diabetic neuropathic foot ulcers are a risk factor for lower leg amputation. Many experts recommend offloading with fibreglass total contact casting, removable cast walkers, and irremovable cast walkers as a way to treat these ulcers. Methods We completed a health technology assessment, which included an evaluation of clinical benefits and harms, value for money, and patient preferences for offloading devices. We performed a systematic literature search on August 17, 2016, to identify randomized controlled trials that compared fibreglass total contact casting, removable cast walkers, and irremovable cast walkers with other treatments (offloading or non-offloading) in patients with diabetic neuropathic foot ulcers. We developed a decision-analytic model to assess the cost-effectiveness of fibreglass total contact casting, removable cast walkers, and irremovable cast walkers, and we conducted a 5-year budget impact analysis. Finally, we interviewed people with diabetes who had lived experience with foot ulcers, asking them about the different offloading devices and the factors that influenced their treatment choices. Results We identified 13 randomized controlled trials. The evidence suggests that total contact casting, removable cast walkers, and irremovable cast walkers are beneficial in the treatment of neuropathic, noninfected foot ulcers in patients with diabetes but without severe peripheral arterial disease. Compared to removable cast walkers, ulcer healing was improved with total contact casting (moderate quality evidence; risk difference 0.17 [95% confidence interval 0.00–0.33]) and irremovable cast walkers (low quality evidence; risk difference 0.21 [95% confidence interval 0.01–0.40]). We found no difference in ulcer healing between total contact casting and irremovable cast walkers (low quality evidence; risk difference 0.02 [95% confidence interval −0.11–0.14]). The economic analysis showed that total contact casting and irremovable

  20. Die partypolitiek en die toekoms van die Afrikaanse volkskultuur

    A.P. Treurnicht

    1970-03-01

    Full Text Available Reeds in 1853 het die Zuid Afrikaan hom soos volg uitgelaat: „Dis ’n dwaling wat ons reeds meermale bestry het dat ons as Britse onderdane verplig sou wees, om die Britse nasionaliteit ons s’n te maak. Die Kolonis van Hollandse oorsprong kan geen Engelsman word nie, en moet ook geen Nederlander wil wees nie. Wanneer hy weet om sy standpunt te waardeer, dan sal hy as verligte kolonis die grondtrekke van die Engelse volkskarakter met dié van die Nederlandse harmonies leer verenig en daardeur word wat hy as Kapenaar moet word.”

  1. Die Voortrekker-Monument

    Gerard Moerdyk

    1938-03-01

    Full Text Available Die Eeufeesjaar is vir die Afrikaner ’n tydperk van besieling. Nog nooit sedert die ontstaan van ons volk het een enkele gebeurtenis soveel nasietrots gewek as die honderdjarige herdenking van die Groot Trek. Vir die eerste keer in ons geskiedenis voel ons ons nie meer Kapenaars, Vrystaters, Natalers, en Transvalers nie, maar Afrikaners, saamgesnoer deur die tradisies van ’n selfstandige kultuurvolk. Wanneer die klimaks van die Ossewatrek met die hocksteenlegging van die Voortrekker-Monument bereik word, sal die besieling nie uitsterf nie, die krag wat geskep is sal bly voortgroei tot ’n onweerstaanbare mag. Die Afrikaner sal homself vind, en as die Monument na sowat vyf jaar onthul word, sal die saad wat in hierdie jaar gesaai is, tot voile rypheid gekom het. Dan sal die Monument self tot die volk spreek; intussen egter, is dit wenslik, nee noodsaaklik selfs, om die Monument aan die Afrikaners te verklaar, om ‘n uiteensetting te gee van die noodsaaklikheid van so ’n Monument, sowel as om die motief te verduidelik wat as inspirasie gedien het vir die ontwerpdaar van.

  2. Approaches to the final storage of radioactive waste in the Federal Republic of Germany. Will responsibility be shifted to future generations?; Wege zur Endlagerung radioaktiver Abfaelle in der Bundesrepublik Deutschland. Wird die Verantwortung auf zukuenftige Generationen verschoben?

    Thomauske, B. [Vattenfall Europe Nuclear Power GmbH, Hamburg (Germany)

    2004-04-01

    With respect to the management of high-level radioactive waste in Germany, there is agreement on these premises: - The waste is to be stored permanently in the Federal Republic of Germany. - A repository is to be operational by 2030. - Final storage is to be achieved in geologic formations. Differences of opinion exist about these questions: - Should there be only one repository for all types of radioactive waste, or would a breakdown into waste generating heat and waste generating only negligible amounts of heat in different repositories be useful under aspects of safety and requirement? - Will a new site selection procedure be required in an effort to find a suitable site, and would such a selection procedure be able to meet the deadline of 2030 for an operational repository? - After the end of legal proceedings, should the Konrad repository be revamped for waste generating negligible amounts of heat? The analysis presented shows that an operational repository for waste generating heat can be made available only in connection with continued exploration work at Gorleben and demonstration of the suitability of that site and subsequent construction of the repository. If the search for a repository site were started from scratch, the date of commissioning such a facility would be after 2050. In this way, that approach would miss the purpose of not shifting the waste management issue to future generations. Acting responsibly means to build the Konrad repository speedily after completion of the legal proceedings about a permit and, in this way, avoid the addition of more interim stores for waste generating negligible amounts of heat. Further exploration of Gorleben is the way agreed upon and necessary for the creation of a repository for high-level radioactive waste generating heat by 2030. For this purpose, the 'points of doubt' must be resolved speedily. (orig.) [German] Im Hinblick auf die Entsorgung hochradioaktiver Abfaelle in Deutschland besteht

  3. Optimization of squeeze casting parameters for non symmetrical AC2A aluminium alloy castings through Taguchi method

    Senthil, P.; Amirthagadeswaran, K. S.

    2012-01-01

    This paper reports a research in which an attempt was made to prepare AC2A aluminium alloy castings of a non symmetrical component through squeeze casting process. The primary objective was to investigate the influence of process parameters on mechanical properties of the castings. Experiments were conducted based on orthogonal array suggested in Taguchi's offline quality control concept. The experimental results showed that squeeze pressure, die preheating temperature and compression holding time were the parameters making significant improvement in mechanical properties. The optimal squeeze casting condition was found and mathematical models were also developed for the process

  4. Die Britse owerheid en die onderwys op Heidelberg gedurende die ...

    The establishment of Christian National Education (CNE) Schools stimulated the concept of mother tongue education. Oor die klaskamerpraktyk en die werklike gehalte van onderrig tydens die kampskooltydperk is daar min bekend. Heidelberg wat na 1902 in 'n belangrike onderwyssentrum in Transvaal ontwikkel het, het ...

  5. Die belangrikste kenmerk van die diereproduksie- bedrywe oor die ...

    digdhede teen 1980 uit 'n kudde van 30 rnilj.skape ge- produseer moet word. Tweedens sal die faktore ... die Republiek van Suid-Mrika teen 1980 in totaal 28 milj. sal wees. Indien die produsente dit as 'n ..... Appendix Table 4 in Digestive Physiology and nutrition of ruminants Vol. 3 Ed. and Publ. D.C. Church, Oregon State ...

  6. DIE ROL VAN DIE TAALWETENSKAP IN DIE ONTWIKKELING VAN ...

    aanslag op die sogenaamde "Intentional Fallacy", heelwat verder. n. Mens sou hier eintlik ook op die invloed van Lacan se toepassing van. De Sacs sure op Freud moet wys, en op Macherey se Theory of Literary. Production. Barthes is naamlik besig om repressie teen te werk, en die teks as produksieproses in stede van ...

  7. Relationship between casting modulus and grain size in cast A356 aluminium alloys

    Niklas, A; Abaunza, U; Fernández-Calvo, A I; Lacaze, J

    2012-01-01

    Microstructure of Al-Si alloy castings depends most generally on melt preparation and on the cooling rate imposed by the thermal modulus of the component. In the case of Al-Si alloys, emphasis is put during melt preparation on refinement of pro-eutectic (Al) grains and on modification of the Al-Si eutectic. Thermal analysis has been used since long to check melt preparation before casting, i.e. by analysis of the cooling curve during solidification of a sample cast in an instrumented cup. The conclusions drawn from such analysis are however valid for the particular cooling conditions of the cups. It thus appeared of interest to investigate how these conclusions could extrapolate to predict microstructure in complicated cast parts showing local changes in the solidification conditions. For that purpose, thermal analysis cups and instrumented sand and die castings with different thermal moduli and thus cooling rates have been made, and the whole set of cooling curves thus recorded has been analysed. A statistical analysis of the characteristic features of the cooling curves related to grain refinement in sand and die castings allowed determining the most significant parameters and expressing the cube of grain size as a polynomial of these parameters. After introduction of a further parameter quantifying melt refining an excellent correlation, with a R 2 factor of 0.99 was obtained.

  8. Wêreldmededingendheid en die tegnologie

    C. W. I. Pistorius

    1996-07-01

    Full Text Available Afgesien van die interne uitdagings wat die Heropbou- en Ontwikkelingsprogram (HOP aan Suid-Afrika bied, moet die land ook tred hou met die veranderende globale omgewing, spesifiek die toenemende belangrikheid van ekonomiese sekuriteit as komponent van nasionale sekuriteit. Die konsep van mededingendheid vergestalt die doelwit wat nagestreef moet word ten einde die ontluikende globale ekonomiese stryd aan te durf. As ’n belangrike drywer van ekonomiese welvaart is tegnologie een van die belangrikste sleutels tot internasionale mededingendheid. Tegnologiese innovasie is die proses wat as hefboom hiervoor gebruik moet word. Dit is egter nodig dat tegnologie, en spesifiek die proses van tegnologiese innovasie, formeel en gestruktureerd bestuur moet word, sowel op nasionale as firmavlak. Op nasionale vlak is die voorsiene Nasionale Innovasiestelsel beslis ’n stap in die regte rigting.

  9. Die spel van assosiasies in en om 'Die verlossing van die beeld' van Breyten Breytenbach

    P.A. du Toit

    2005-07-01

    Full Text Available The play of association in and around 'The liberation of the image' by Breyten Breytenbach This analysis focuses on the conjunction of memory and imagination, which is an important impulse in, and key to, Breytenbach’s work. The play with language and with associations, the foregrounding, in the short story, “Die verlossing van die beeld” (Breytenbach, 1983 with its metafictional title and apparently divergent motifs (rain/water, watch, onion, the death and burial of a grandfather acts, as it were, as an invitation to the reader to become a co-player. The reader ventures on a search for traces, intertextual links within the Breytenbach oeuvre and for already acknowledged influences such as Surrealism (which in turn casts some light on the strange title of the story and the Eastern philosophies such as Zen and the even older Taoism. The analysis also takes into account the context in which “Mouroir” was written, namely Breytenbach’s term in prison (1975-1982. Seeing that the writer had to hand in his manuscripts to the jail authorities regularly, he might have decided, consciously or by intuition, to hide some thoughts and feelings behind a screen or a mask, in, for example in “Die verlossing van die beeld”, a lighter tone and irony.

  10. Artikel 2 van die Nederlandse Geloofsbelydenis as geloofsvooronderstelling in die gesprek tussen wetenskap en geloof

    Jan A. Erasmus

    2014-09-01

    Full Text Available Artikel 2 van die Nederlandse Geloofsbelydenis bely dat God deur twee middele geken word, te wete deur middel van die skepping, onderhouding en regering van die wêreld (waaronder die wetenskap en deur die heilige en goddelike Woord (die Bybel. Hierdie belydenis is van groot belang vir die gesprek tussen Wetenskap en Teologie. In hierdie artikel word gepoog om die verskille, maar ook die ooreenkomste tussen hierdie twee middele van openbaring uit te lig, elkeen tot sy reg te laat kom, maar hulle ook in balans met mekaar te stel. Die wyse waarop te werk gegaan word, is die volgende: eers word gestel wat vooronderstellings is, asook die plek wat vooronderstellings in die beoefening van wetenskap sowel as geloof inneem. Daarna word nagevors watter perspektiewe artikel 2 van die Nederlandse Geloofsbelydenis as geloofsvooronderstelling vir die wetenskaps- en teologiebeoefening respektiewelik bied. Hieruit word ’n aantal gevolgtrekkings gemaak wat kan help om die problematiek in die wetenskap-geloofsgesprek op te los. Die kernbevinding van hierdie artikel is die volgende: Vanweë die verskil in die aard en die doel tussen Bybelfeite en wetenskaplike navorsingsresultate kan en sal klaarblyklike harmonieprobleme tussen die Skrif en die wetenskap ontstaan. Hierdie is egter slegs klaarblyklike probleme, omdat ’n verrekening van die verskil in die aard en die bedoeling van die wetenskapresultate en die Bybelfeite hierdie probleem sal oplos. Article 2 of the Belgic Confession as faith presupposition in the science-faith debate. Article 2 of the Belgic Confession confesses that God can be known by two means: firstly by studying the creation, preservation and government of the universe (i.e. science and secondly by studying the Word of God (the Bible. This confession is very important for the discussion between science and faith. In this article the similarities, but also the differences between these two means of revelation are researched. The aim is to

  11. die ontstaan en die ontwikkeling van die skoolkadette-stelsel in die rsa

    toe algemene diensplig ingestel is. Die diens- plig het intussen sy volle beslag gekry en in. Weermagkringe het die gedagte posgevat dat skoolkadette. 'n deeglike ondersoek vereis ten einde die skoolgaande seun vir sy komende nasionale diensplig te orienteer. Tydens kadetopleldlng leer die seuns al die fynere kunsles ...

  12. Van die Gasredakteur

    cherish and teach.'1. Die Fakulteit Geneeskunde van die Universiteit van die Oranje-Vrystaat het pragtig gegroei ge- durende die eerste 21 jaar van sy bestaan. Die entoesiasme, doelgerigtheid, harde werk en inisia- tiewe van 'n groot aantal persone was hiervoor verantwoordelik. 'If we see a bit more clearly than they, it is ...

  13. Halfkrone vir die Nagmaal

    Owner

    die omgewing van Velddrif en Laaiplek, ook noordwaarts verby Lambertsbaai tot by. Doringbaai en Strandfontein. “Haar seeverhale is Sussie (Kotze) se belangrikste bydrae tot die Afrikaanse letterkunde”, sê Kotzé-Myburgh in die voorwoord van die versamelbundel. Die leser word herinner aan Kotze se debuutroman, ...

  14. Marginal Accuracy of Castings Produced with Different Investment Systems.

    Yadav, R K

    2009-04-01

    The use of casting ring to produce accurate castings has been challenged with the introduction of a ringless casting technique. This study compared the marginal accuracy of all - metal complete coverage crowns fabricated with ringless, split plastic ring and metal ring investment systems. A total of 40 all- metal complete coverage crowns were fabricated on a metal die. The crowns were divided in 4 groups (Group A, B, C and D) of 10 patterns each. A ringless system of investing and casting was used for group A whereas a split plastic ring system was used for group B. Groups C and D utilized metal ring with single and double layers of asbestos free cellulose acetate liner respectively for investing and casting procedures. The restorations were seated on the metal die and the vertical marginal discrepancy was evaluated by measuring the gap between the finish line on the die and the margins of the crown on four specific sites with an optical microscope. Statistical analysis was carried out using ANOVA and multiple comparison "t" test. The mean vertical marginal discrepancy for groups A, B, C and D was 95μm, 136μm, 128μm and 104μm respectively. Vertical marginal discrepancy on each surface was compared among the four groups. Difference of vertical marginal discrepancy on buccal surface (p0.05). Accurate castings with better marginal fit can be produced with ringless casting technique.

  15. Die teologie in gesprek met die ekonomie

    (1723-1790) sy vertrekpunt neem, ontwikkel, as oorwinnaars uit die Franse Revolu .... Die onmiddellike sukses van Adam Smith se 'Wealth of Nations' was .... alle vorme van sosialisme niks anders as 'kommunisme' (Wassenaar 1977:12) nie.

  16. DE-NE0000724 - Research Performance Final Report - Investigation of Thermal Aging Effects on the Evolution of Microstructure and Mechanical Properties of Cast Duplex Stainless Steels

    Ankem, Sreeramamurthy [University of Maryland, College Park, MD (United States); Perea, Daniel E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kolli, R. Prakash [University of Maryland, College Park, MD (United States); Mburu, Sarah [University of Maryland, College Park, MD (United States); Schwarm, Samuel C. [University of Maryland, College Park, MD (United States)

    2017-12-11

    This report details the research activities carried out under DOE-NEUP award number DE-NE0000724 concerning the evolution of structural and mechanical properties during thermal aging of CF–3 and CF–8 cast duplex stainless steels (CDSS). The overall objective of this project was to use state-of-the-art characterization techniques to elucidate trends and phenomena in the mechanical and structural evolution of cast duplex stainless steels (CDSS) during thermal aging. These steels are commonly used as structural materials in commercial light water nuclear power plants, undergoing aging for decades in operation as cooling water pipes, pump casings, valve bodies, etc. During extended exposure to these conditions, CDSS are known to undergo a change in mechanical properties resulting in a loss of ductility, i.e. embrittlement. While it is generally accepted that structural changes within the ferrite phase, such as decomposition into iron (Fe)-rich and chromium (Cr)-rich domains, lead to the bulk embrittlement of the steels, many questions remain as to the mechanisms of embrittlement at multiple length scales. This work is intended to shed insight into the atomic level composition changes, associated kinetic mechanisms, and effects of changing phase structure on micro- and nano-scale deformation that lead to loss of impact toughness and tensile ductility in these steels. In general, this project provides a route to answer some of these major questions using techniques such as 3-dimensional (3-D) atom probe tomography (APT) and real-microstructure finite element method (FEM) modeling, which were not readily available when these steels were originally selected for service in light water reactors. Mechanical properties evaluated by Charpy V-notch impact testing (CVN), tensile testing, and microhardness and nanohardness measurements were obtained for each condition and compared with the initial baseline properties to view trends in deformation behavior during aging

  17. Segregation in cast products

    Unknown

    The agreement with experimental data is mostly qualitative. The paper also ... For example, a high degree of positive segregation in the central region .... solute in a cast product, important ones being: size of casting, rate of solidification, mode.

  18. DIE PERSOON VAN VREDE IN DIE SENDING

    aan dat 'n lewe onder die gesag van God tot volle vrede lei: “In coming under the rule of Yahweh, moreover, life was made whole and safe.” Dit is spesifiek in die tempel waar die volheid van God se vrede ondervind word (1997:662):. The temple is indeed the place where Israel entered into Yahweh's full zone of shalom.

  19. Structure Distribution in Precise Cast Iron Moulded on Meltable Model

    Skrbek B.

    2015-12-01

    Full Text Available Topic of this work is to compare metalurgy of cast irons poured into sand moulds and into shell molds at IEG Jihlava company and from it following differencies in structures of thin- and thick-walled castings. This work is dealing with investigation and experimental measurement on surfaces and sections suitable thin- and thick-walled investment castings at IEG Jihlava. Cast irons with flake graphite (grey cast iron and cast irons with spheroidal graphite (ductile cast iron. Both mechanical and physical properties are determined using calculations from as measured values of wall thicknesses L and Lu, Vickers hardness and remanent magnetism. Measurement results are discussed, findings are formulated and methods for castings metallurgical quality improvement are recommended finally.

  20. n Oorsig van die huidige stand van navorsing oor die

    Test

    7 Jun 2011 ... Die eerste maal wat dit as deel van die teks van 1 Johannes aangehaal word, is in die. 4de eeu in 'n Latynse teks, Liber Apologeticus (hf 4). Eers aan die einde van die 16de eeu is dit in 'n amptelike Katolieke uitgawe van die Vulgaat ingesluit. Die doel van die Johannesbriewe. Waarom is die Briewe ...

  1. Low Loss Advanced Metallic Fuel Casting Evaluation

    Kim, Kihwan; Ko, Youngmo; Kim, Jonghwan; Song, Hoon; Lee Chanbock

    2014-01-01

    The fabrication process for SFR fuel is composed of fuel slug casting, loading and fabrication of the fuel rods, and the fabrication of the final fuel assemblies. Fuel slug casting is the dominant source of fuel losses and recycles streams in the fabrication process. Recycle streams include fuel slug reworks, returned scraps, and fuel casting heels, which are a special concern in the counter gravity injection casting process because of the large masses involved. Large recycle and waste streams result in lowering the productivity and the economic efficiency of fuel production. To increase efficiency the fuel losses in the furnace chamber, crucible, and the mold, after casting a considerable amount of fuel alloy in the casting furnace, will be quantitatively evaluated. After evaluation the losses will be identified and minimized. It is expected that this study will contribute to the minimization of fuel losses and the wastes streams in the fabrication process of the fuel slugs. Also through this study the technical readiness level of the metallic fuel fabrication process will be further enhanced. In this study, U-Zr alloy system fuel slugs were fabricated by a gravity casting method. Metallic fuel slugs were successfully fabricated with 19 slugs/batch with diameter of 5mm and length of 300mm. Fuel losses was quantitatively evaluated in casting process for the fuel slugs. Fuel losses of the fuel slugs were so low, 0.1∼1.0%. Injection casting experiments have been performed to reduce the fuel loss and improve the casting method. U-Zr fuel slug having φ5.4-L250mm was soundly fabricated with 0.1% in fuel loss. The fuel losses could be minimized to 0.1%, which showed that casting technology of fuel slugs can be a feasible approach to reach the goal of the fuel losses of 0.1% or less in commercial scale

  2. Die Ware Buch und die Philologie

    Bernhard Hurch

    2017-10-01

    Full Text Available Die im 19. Jahrhundert sich verändernden Produktionsbedingungen für Druckwerke (Buchdruck, Satz, Papier, Bindung wirkten katalysierend auf die Fachkonstitution und Institutionalisierung der Philologien. Hier steht der tatsächliche Buchmarkt im Vordergrund der Darstellung, das Käuferpublikum und die Voraussetzungen des Vertriebs. Dazu gehören auch die Rezension als entstehende Textsorte und die rasch arbeitenden Rezensionsorgane. F.-R. Hausmann wurde in den letzten Jahren unentbehrlicher Mitarbeiter dieses im Rahmen des Grazer Schuchardt-Projekts "Netzwerk des Wissens" angesiedelten Ansatzes.

  3. Applying RP-FDM Technology to Produce Prototype Castings Using the Investment Casting Method

    M. Macků

    2012-09-01

    Full Text Available The research focused on the production of prototype castings, which is mapped out starting from the drawing documentation up to theproduction of the casting itself. The FDM method was applied for the production of the 3D pattern. Its main objective was to find out whatdimensional changes happened during individual production stages, starting from the 3D pattern printing through a silicon mouldproduction, wax patterns casting, making shells, melting out wax from shells and drying, up to the production of the final casting itself.Five measurements of determined dimensions were made during the production, which were processed and evaluated mathematically.A determination of shrinkage and a proposal of measures to maintain the dimensional stability of the final casting so as to meetrequirements specified by a customer were the results.

  4. Applying RP-FDM Technology to Produce Prototype Castings Using the Investment Casting Method

    Macků M.

    2012-09-01

    Full Text Available The research focused on the production of prototype castings, which is mapped out starting from the drawing documentation up to the production of the casting itself. The FDM method was applied for the production of the 3D pattern. Its main objective was to find out what dimensional changes happened during individual production stages, starting from the 3D pattern printing through a silicon mould production, wax patterns casting, making shells, melting out wax from shells and drying, up to the production of the final casting itself. Five measurements of determined dimensions were made during the production, which were processed and evaluated mathematically. A determination of shrinkage and a proposal of measures to maintain the dimensional stability of the final casting so as to meet requirements specified by a customer were the results.

  5. Die gebruik van die mite in Die werfbobbejaan van Alexander Strachan

    E. M.M. Klopper

    1996-05-01

    Full Text Available The use of myths in Die werfbobbejaan by Alexander Strachan This article focuses on the rote of Zulu myths in Alexander Strachan’s novel Die werfbobbejaan. It lakes as point of departure sources on mythology like Cuddon (1991, Baldick (1990, Grimal (1969, Levi-Strauss (1979 and Jung (1969. Die werfbobbejaan essentially recounts the story of a man (the adventurer, the academic, the writer, the hunter who also is the central character in Strachan's two preceding novels. Die werfbobbejaan focuses on the completion of an individuation process in the life of the central character, a process already begun in the preceding two novels and which in this novel finally culminates in the confrontation between hunter and baboon. The completion of this process is facilitated by the African milieu of Zululand where people give meaning to their existence by means of myths, and where no distinction is made between the mythic and rational modes of experiencing reality.

  6. Travelling Through Caste

    Kumar, Raj

    2016-01-01

    With its peculiar caste system, India is considered the most stratified of all known societies in human history. This system is ‘peculiar’ as it divides human beings into higher and lower castes and this division is backed by certain religious sanctions based on the sociological concepts of ‘purity’ and ‘pollution’. While the higher caste is associated with ‘purity’, the lower caste is associated with ‘pollution’. The people of the lower castes are not allowed to undertake religious journeys ...

  7. Search for a final repository site. How is the status of the preparation of final radioactive waste disposal in Germany?; Endlagersuche. Wie steht es um die Vorbereitung der Entsorgung radioaktiver Abfaelle in Deutschland?

    Mueller, Monika C.M. (ed.) [Evangelische Akademie Loccum, Rehburg-Loccum (Germany). Arbeitsbereich Naturwissenschaften, Oekologie und Umweltpolitik

    2017-07-01

    During the workshop on the status of the preparation of final radioactive waste disposal in Germany the following issues were discussed: socio-economic challenges two years after the final report of the commission for final disposal of radioactive wastes; the question of public participation - the difficult search for a repository site, experiences and intents of public participation during the work of the commission, interim storage of hear generating radioactive wastes, extended interim-storage, long-term interim storage facilities - opinion of the concerned public, how to establish a controlling and correcting surveillance of the process?.

  8. Die vrede van Münster / Westfale en die betekenis daarvan vir die ...

    In die Suid-Afrikaanse kerkgeskiedenis egter is die Vrede van Münster as epogmakende gebeure tot dusver nie net in die algemeen verwaarloos nie, maar boonop is die direkte verband tussen hierdie sentrale historiese baken aan die een kant en aan die ander kant die vestiging van die VOC se verversingspos aan die ...

  9. Tegnologie en die mens

    omgewingsbesoedeling, volgend op industrialisasie en verstedeliking, gee uit- ing tot krete van wanhoop en frustrasie. Die maatskaplike ontwrigting agv outomatisasie het die begrippe van vervreemding en naam- loosheid op die voorgrond van sosiale be- wustheid geplaas. • Die Neutrale Siening. Tegnologie was nag. 34.

  10. GODSBEELDE IN DIE LITURGIE

    15 Mei 2010 ... Biezeveld, de Boer, Brümmer, Muis. 2001; Brown 2006; Durand 2007). ... Wanneer sal hy weer in God se teenwoordigheid verskyn (vers 3)? Dié vraag is vol onsekerheid. (Schuman 2004:8). Sy onsekerheid ... God se volk en die enkeling in die geskiedenis het al die trou van God ervaar waarop die digter ...

  11. Varswateralge en die ekonomie

    W. E. Scott

    1988-03-01

    Full Text Available Die artikel bespreek die ekonomiese belong wat varswateralge alreeds het en hul moontlike verdere ontginning in die toekoms. Sowel gewenste as ongewenste aspekte word oorweeg en hoofsaaklik met voorbeelde uit Suid-Afrika geïllustreer. Die oormatige ontwikkeling van ongewenste alge in varswater verlaag die watergehalte dear verskeie chemiese veranderinge, wat kan wissel van smake en geure tot die produksie van verbindings wat gesondheidsgevare vir mens of dier inhou. Verwydering van ongewenste alge dra aansienlik by tot die koste van waterbehandeling. Oormatige alggroei belemmer ontspanningsgebruike en kan eiendomswaardes langs rivier- en damoewers beïnvloed.

  12. Prediking aan die hand van die metafoor van fiksieskryf

    p1243322

    HTS 64(3) 2008 siening van die self en waarheid. In die pre-moderne paradigma kan die dominante metafoor verstaan word aan die hand van 'n spieël wat die lig uit 'n transendente oorsprong weerkaats, terwyl die moderne paradigma uitgedruk word met die metafoor van 'n lamp wat 'n eie, oorspronklike lig binne die self.

  13. e .Kuraioriufn. DIE W ETENSKAPLIKE BETEKENIS VAN DIE W ERK

    Test

    ENGELBRECHT ver antwoordelik vir die Ou-Testamentiese vakke en Hebreeus. Die aan stelling van 'n derde professor het noodsaaklik geword, want dit sou. 85 .... De .Spreuken ran 5a/o?no omvat die nuwe vertaling en die ekse gese van die eerste 24 hoofstukke van die Spreukeboek. Die geskoold- heid in die Semitiese ...

  14. Cast erosion from the cleaning of debris after the use of a cast trimmer.

    Hansen, Paul A; Beatty, Mark W

    2017-02-01

    Whether using tap water to rinse off debris will make a clinical difference to the surface detail of a gypsum cast is unknown. In addition, how best to remove debris from the cast is unknown. The purpose of this in vitro study was to evaluate the efficiency of different methods of cleaning a gypsum cast after trimming and the effect of short-term exposure to tap water on the surface quality of the cast. A die fitting American National Standards Institute/American Dental Association specification 25 (International Standards Organization specification 6873) for dental gypsum products was embedded in a Dentoform with the machined lines positioned at the same level as the occlusal surface of the posterior teeth. A flat plate was used to ensure that the plane of occlusion for the die was at the same position as the posterior teeth. Forty polyvinyl siloxane impressions of the Dentoform were made and poured with vacuum-mixed improved Type IV dental stone. Each cast was inspected for the accurate reproduction of the lines. The base of the 2-stage pour was trimmed with a cast trimmer with water, and surface debris was removed by rinsing by hand under tap water for 10 seconds, by brushing the cast with a soft toothbrush for 10 seconds, or by resoaking the cast and using a soft camel hair brush in slurry water for 10 seconds. The amount of debris was evaluated on a scale of 1 to 4, and the quality of the 20-μm line was evaluated on a scale of 1 to 4 under ×15 magnification. The nonparametric Kruskal-Wallis ranks test was used to identify significant differences among the different cleaning methods (α=.05). Results of the Kruskal-Wallis and Kruskal-Wallis Z-value tests demonstrated that all cleaning methods produced cleaner casts than were observed for uncleansed controls (P<.001), but no differences in debris removal were found among the different cleaning methods (.065≤P≤.901). The ability to see the quality of a 20-μm line (P=.974) was not statistically different

  15. Die dialogiese prinsipe

    J. J. de Klerk

    1981-08-01

    Full Text Available Met die dialogiese prinsipe word daardie beginsel bedoel, waarin die tweerigtingverkeer of kommunikasie onder, of met, of deur die mense op 'n heel besondere gesprekmatige wyse gere�l word. Tot die wese van die dialogiese prinsipe behoort "als Grundvoraussetzung das Ernstnehmen des Gesprachspartners und das darin enthaltene zuhoren-konnen. Dialog ist also etwas anderes als Disput oder Diskussion. Er setzt gegenseitiges Vertrauen und Hochachtung voraus."

  16. Die sestienpersoonlikheidsfaktorvraelys as hulpmiddel by die takseersentrum

    J. C. D. Augustyn

    1988-05-01

    Full Text Available The 16PF Personality Test as an aid to the assessment centre Assessment centres still remains costly and thime consuming. This study investigates the reduction of time and costs by the use of the 16 PF Personality Test as a method for measuring management dimensions. Promising results were obtained with a relatively small sample for the prediction of initiative and perseverance. Significant multiple correlations were also found for three criteria of management success. Further research may establish the use of the 16 PF as an aid to management assessment and thereby reduce the costs and time involved in assessment centres. Opsomming Takseersentrums se grootste probleem is gelee in die koste en tyd wat dit behels. Hierdie studie ondersoek die moontlikheid om beide te verminder deur die aanwending van die 16 PF Persoonlikheidsvraelys vir die meting van bestuursdimensies. Belowende resultate is met 'n relatiewe klein steekproef bevind ten opsigte van die voorspelling van inisiatiefen deursettingsvermoe. Beduidende meervoudige korrelasies is ook ten opsigte van drie kriteria van bestuursukses bevind. Verdere navorsing kan die gebruik van die 16 PF as hulpmiddel by bestuursevaluering vestig en sodoende die tydsduur en koste van takseersentrums verminder.

  17. Reengineering of Permanent Mould Casting with Lean Manufacturing Methods

    R. Władysiak

    2007-07-01

    Full Text Available At the work were introduced main areas of production system project of casts produced in permanent moulds, that constitutes reengineering of conventional production system according to Lean Manufacturing (LM methods. New resolution of cooling of dies with water mist was shown to casting of car wheels made from aluminium alloys in low pressure casting process. It was implemented as a part of goal-oriented project in R.H. Alurad Sp.z o.o. in Gorzyce. Its using intensifies solidification and self-cooling of casts shortening the time of casting cycle by the 30%. It was described reorganizing casting stations into multi-machines cells production and the process of their fast tool’s exchange with applying the SMED method. A project of the system was described controlling the production of the foundry with the computer aided light Kanban system. A visualization of the process was shown the production of casts with use the value stream mapping method. They proved that applying casting new method in the technology and LM methods allowed to eliminate down-times, to reduce the level of stocks, to increase the productivity and the flow of the castings production.

  18. Research on Accuracy of Automatic System for Casting Measuring

    Jaworski J.

    2016-09-01

    Full Text Available Ensuring the required quality of castings is an important part of the production process. The quality control should be carried out in a fast and accurate way. These requirements can be met by the use of an optical measuring system installed on the arm of an industrial robot. In the article a methodology for assessing the quality of robotic measurement system to control certain feature of the casting, based on the analysis of repeatability and reproducibility is presented. It was shown that industrial robots equipped with optical measuring systems have the accuracy allowing their use in the process of dimensional control of castings manufactured by lost-wax process, permanent-mould casting, and pressure die-casting.

  19. DIE GESKIEDENIS VAN AFDELING LOGISTIEK

    1 Aug 1978 ... dan ook aangebied, Agv die probleem wat ont- staan het met die gebrek aan goedgekeurde poste vir die Afdeling en as gevolg van die ver- wagte vertraging met die ondersoek van die. DOS-span, het die Afdeling Logistiek en Afde- ling Personeel oorleg gepleeg en laasgenoemde het ingestem dat die ...

  20. [Dying with cancer: Hollywood lessons].

    Niemeyer, Fernanda; Kruse, Maria Henriqueta Luce

    2013-12-01

    The study attempts to understand how dying from cancer is portrayed by five movies produced in Hollywood between 1993 and 2006. Based on the cultural studies and their post-structuralism version and supported by the notions of discourse and subjectivity, as proposed by philosopher Michel Foucault, we suggest one of the possible readings of the movie picture corpus. We assess how the movie picture discourse acts as a cultural pedagogy that produces ways of seeing dying with cancer: immortalizing the healthy body image, silencing death, taking care of the dead body and, finally, accepting death. Our proposal is intended to stimulate reflections that may contribute to care and education in nursing.

  1. Evaluating the Tensile Properties of Aluminum Foundry Alloys through Reference Castings-A Review.

    Anilchandra, A R; Arnberg, Lars; Bonollo, Franco; Fiorese, Elena; Timelli, Giulio

    2017-08-30

    The tensile properties of an alloy can be exploited if detrimental defects and imperfections of the casting are minimized and the microstructural characteristics are optimized through several strategies that involve die design, process management and metal treatments. This paper presents an analysis and comparison of the salient characteristics of the reference dies proposed in the literature, both in the field of pressure and gravity die-casting. The specimens produced with these reference dies, called separately poured specimens, are effective tools for the evaluation and comparison of the tensile and physical behaviors of Al-Si casting alloys. Some of the findings of the present paper have been recently developed in the frame of the European StaCast project whose results are complemented here with some more recent outcomes and a comprehensive analysis and discussion.

  2. Caste and power

    Roy, Dayabati

    2011-01-01

    This paper explores the institution of caste and its operation in a micro-level village setting of West Bengal, an Indian state, where state politics at grass roots level is vibrant with functioning local self-government and entrenched political parties. This ethnographic study reveals that caste...... relations and caste identities have overarching dimensions in the day-to-day politics of the study villages. Though caste almost ceases to operate in relation to strict religious strictures, under economic compulsion the division of labour largely coincides with caste division. In the cultural......–ideological field, the concept of caste-hierarchy seems to continue as an influencing factor, even in the operation of leftist politics....

  3. Impact of Simulation Technology on Die and Stamping Business

    Stevens, Mark W.

    2005-08-01

    Over the last ten years, we have seen an explosion in the use of simulation-based techniques to improve the engineering, construction, and operation of GM production tools. The impact has been as profound as the overall switch to CAD/CAM from the old manual design and construction methods. The changeover to N/C machining from duplicating milling machines brought advances in accuracy and speed to our construction activity. It also brought significant reductions in fitting sculptured surfaces. Changing over to CAD design brought similar advances in accuracy, and today's use of solid modeling has enhanced that accuracy gain while finally leading to the reduction in lead time and cost through the development of parametric techniques. Elimination of paper drawings for die design, along with the process of blueprinting and distribution, provided the savings required to install high capacity computer servers, high-speed data transmission lines and integrated networks. These historic changes in the application of CAE technology in manufacturing engineering paved the way for the implementation of simulation to all aspects of our business. The benefits are being realized now, and the future holds even greater promise as the simulation techniques mature and expand. Every new line of dies is verified prior to casting for interference free operation. Sheet metal forming simulation validates the material flow, eliminating the high costs of physical experimentation dependent on trial and error methods of the past. Integrated forming simulation and die structural analysis and optimization has led to a reduction in die size and weight on the order of 30% or more. The latest techniques in factory simulation enable analysis of automated press lines, including all stamping operations with corresponding automation. This leads to manufacturing lines capable of running at higher levels of throughput, with actual results providing the capability of two or more additional strokes per

  4. Wear resistant PVD-/CVD-dry lubricant coatings for the environmental and innovative production. Subproject 3: dry lubricant coatings - carbon coatings. Final report; Verschleissfeste PVD-/CVD-Trockenschmierstoffschichten fuer die umweltschonende und innovative Fertigung. Teilprojekt 3: Kohlenstoffbasierte Trockenschmierstoffschichten (TSS-C). Abschlussbericht

    Schattke, A.; Hockauf, W.

    2002-09-05

    The partners Bosch, Metaplas Ionon and Roth and Rau developed dry lubricant coatings on a carbon coating base. The cutting tools used for the testing were developed in former dry cutting projects especially for cutting with minimum quantity lubrication (MQL). The coatings were tested in cutting and metal forming. After tribological testing at the coating companies the deposited coatings were evaluated by machining tests in drilling, thread forming and metal forming at the universities of Darmstadt and Kassel. The best coatings were tested in production field tests (laboratory) or, if possible, in the production at company Bosch and at other end users of the joint project. It was possible to show that carbon coatings are very good at punching and sheet bending. Also at drilling and thread forming in cast iron and low alloyed steels the results are good enough for production. The results at drilling and thread forming in aluminium alloys and high alloyed steels (X90CrMoV18) were not good enough for production under dry conditions. But testing with a reduced amount of MQL (6ml/h) showed better cutting parameters than commercial coatings. Also cutting length and quality of the parts are better. Even with the best coatings it was not possible to make dry massive forming with reduced temperature. At these high temperatures and high surface pressures it was not possible to work without lubricants. (orig.) [German] Im Projekt wurden von den Partnern Bosch, Metaplas Ionon und Roth and Rau Trockenschmierstoffschichten auf Kohlenstoffbasis entwickelt. Diese wurden auf Werkzeuge abgeschieden, deren Geometrien in bereits abgeschlossenen Projekten fuer die Trockenzerspannung mit Minimalmengenschmierung optimiert wurden. Die Schichten sind fuer die Zerspannung und Umformtechnik vorgesehen. An tribologische Tests bei den Beschichtern schlossen sich Filtertests an den Hochschulen Darmstadt und Kassel an, bei denen die Schichten in Bohr-, Gewindeform- und Umformtests untersucht

  5. SLIP CASTING METHOD

    Allison, A.G.

    1959-09-01

    S>A process is described for preparing a magnesium oxide slip casting slurry which when used in conjunction with standard casting techniques results in a very strong "green" slip casting and a fired piece of very close dimensional tolerance. The process involves aging an aqueous magnestum oxide slurry, having a basic pH value, until it attains a specified critical viscosity at which time a deflocculating agent is added without upsetting the basic pH value.

  6. Die relevansie van die boek Prediker

    ook in die dogmatiek te bespeur is nie. 'n Vinnige oorsig oor die teksverwysings van. 'n paar wydgelese dogmatiekhandboeke kan dit bevestig. In Karl Barth se omvang- ryke Kirchliche Dogmatik word Prediker slegs vyf en dertig maal aangehaal en slegs sewe maal word teksgedeeltes bespreek. Emil Brunner haal Prediker ...

  7. Caste in Itself, Caste and Class, or Caste in Class

    Ramkrishna Mukherjee

    2015-01-01

    After the British conquered Bengal and eventually the whole of India,they set out to administer the colony. In this context they encountered two phenomena with which they were not familiar: (1) the relation of people to land for production (and not for revenue receiving, household living, etc.), and (2) the caste system of India, viz. the jati strati?cation of society.

  8. Study of protective coatings for aluminum die casting molds

    Peter, Ildiko, E-mail: ildiko.peter@polito.it; Rosso, Mario; Gobber, Federico Simone

    2015-12-15

    Highlights: • Development and characterization of some protective coatings on steel substrate, realized by plasma spray techniques, were presented. • The substrate material used is a Cr–Mo–V based hot work tool steel. • The main attention is on the study of wear and on the characterization of the interface, because of their key role in determining the resistance of the coating layer. • Simulation of friction and wear processes is performed by pin-on-disk test and the tested samples are observed by scanning electron microscopy. - Abstract: In this paper, the development and characterization of some protective coatings on steel substrate are presented. The coatings are realized by plasma spray techniques. The substrate material used is a Cr–Mo–V based hot work tool steel, initially submitted to vacuum heat treatment to achieve homogeneous hardness. The main attention is focused on the study of wear and on the characterization of the interface between the substrate material and the coating layer, because of their key role in determining the resistance of the coating layer. Simulation of friction and wear processes is performed by pin-on-disk test and the tested samples are observed by scanning electron microscopy.

  9. The deformation of wax patterns and castings in investment casting technology

    A. Herman

    2012-01-01

    Full Text Available The dimensional accuracy of the final casting of Inconel alloy 738 LC is affected by many aspects. One of them is the choice of method and time of cooling wax model for precision investment casting. The main objective was to study the initial deformation of the complex shape of the casting of the rotor blades. Various approaches have been tested for cooling wax pattern. When wax models are cooling on the air, without clamping in jig for cooling, deviations from the ideal shape of the casting are very noticeable (up to 8 mm and most are in extreme positions of the model. When blade is cooled in fixing jig in water environment, the resulting deviations compared with cooling in air are significantly larger, sometimes up to 10 mm. This itself does not mean that the final shape of the casting is dimensionally more accurate with usage of wax models, which have deviations from the ideal position smaller. Another deformation occurs when shell mould is produced around wax pattern and furthermore deformations emerge while casting of blade is cooling. This paper demonstrates first steps in describing complex process of deformations of Inconel alloy blades produced with investment casting technology by comparing results from thermal imagery, simulations in foundry simulation software ProCAST 2010 and measurements from CNC scanning system Carl Zeiss MC 850. Conclusions are so far not groundbreaking, but it seems deformations of wax pattern and deformations of castings do in some cases cancel each other by having opposite directions. Describing entirely whole process of deformations will help increase precision of blade castings so that models at the beginning and blades in the end are the same.

  10. Microstructural and mechanical properties investigation of Mg-Al-Zn alloy counter gravity investment cast

    Mutombo, K

    2009-10-01

    Full Text Available . The most common manufacturing method for the production of Mg components is via High Pressure Die Casting (HPDC), however, this process is suitable for high volume thin walled components. Investment casting offers the capability of producing complex near...

  11. P. J. N. Smal, Die Universalisme in die Psalms. Academisch ...

    Test

    dat die historiese element in Israel se Godsopenbaring en daarmee die insig in sy betekenis te kort gedoen word. Die betekenis van die studie vir die historia revelationis is daardeur gering; as duidelike „tydlose” sistematisering van Outestamentiese gegewens oor die betrokke onder- werpe, soos die laaste hoofstuk, bl.

  12. DIE ONTVC'ERP VAN 'N SENDINGBELEID IN DIE HUIDIGE ...

    Test

    DIE ONTVC'ERP VAN 'N SENDINGBELEID IN DIE. HUIDIGE SITUASIE. Sending is 'n deel van die vervulling van die apostoliese opdrag van die kerk. Dit geskied op grond van en in gehoorsaamheid aan Gods. \\C'oord. Teologiese besinning is daarom die eerste en grondliggende vereiste by die ontwerp van 'n ...

  13. DIE PLEK VAN SANG EN MUSIEK IN DIE PROTESTANTSE ...

    Test

    Sy moet hierdie opdrag uitvoer deur mid del van die Prediking d.w.s. deur middel van die Woord-vorm, maar ook deur die bediening van die sakramente, dws. deur middel van die vorm van die Daad. Maar nou wil God nie hê dat die Kerk slegs één maal die Evangelie sal predik en die mense sal doop om hulle daarna.

  14. Packaged die heater

    Spielberger, Richard; Ohme, Bruce Walker; Jensen, Ronald J.

    2011-06-21

    A heater for heating packaged die for burn-in and heat testing is described. The heater may be a ceramic-type heater with a metal filament. The heater may be incorporated into the integrated circuit package as an additional ceramic layer of the package, or may be an external heater placed in contact with the package to heat the die. Many different types of integrated circuit packages may be accommodated. The method provides increased energy efficiency for heating the die while reducing temperature stresses on testing equipment. The method allows the use of multiple heaters to heat die to different temperatures. Faulty die may be heated to weaken die attach material to facilitate removal of the die. The heater filament or a separate temperature thermistor located in the package may be used to accurately measure die temperature.

  15. Die radio in Afrika

    S. de Villiers

    1966-03-01

    Full Text Available Omvang van radio-uitsendings in en na Afrika. — Redes vir die versnelde tempo van uitbreiding. — Radio as die geskikste massa-kommunikasiemiddel vir Afrika. — Faktore wat die verspreiding bemoeilik. — Skouspelagtige toename in luistertalle.Toe Plinius, wat in die jaar 79 oorlede is, in sy „Historia Naturalis” verklaar het dat daar altyd iets nuuts uit Afrika afkomstig is, kon hy nouliks voorsien het dat die „iets" negentien eeue later in die lug sou setel wat hierdie reuse-vasteland oorspan — ’n Babelse spraakverwarring en ’n ongekende, verbete woorde-oorlog in die etergolwe, onder meer daarop bereken om die harte en hoofde van derduisendes te verower.

  16. Application and further development of models for the final repository safety analyses on the clearance of radioactive materials for disposal. Final report; Anwendung und Weiterentwicklung von Modellen fuer Endlagersicherheitsanalysen auf die Freigabe radioaktiver Stoffe zur Deponierung. Abschlussbericht

    Artmann, Andreas; Larue, Juergen; Seher, Holger; Weiss, Dietmar

    2014-08-15

    The project of application and further development of models for the final repository safety analyses on the clearance of radioactive materials for disposal is aimed to study the long-term safety using repository-specific simulation programs with respect to radiation exposure for different scenarios. It was supposed to investigate whether the 10 micro Sv criterion can be guaranteed under consideration of human intrusion scenarios. The report covers the following issues: selection and identification of models and codes and the definition of boundary conditions; applicability of conventional repository models for long-term safety analyses; modeling results for the pollutant release and transport and calculation of radiation exposure; determination of the radiation exposure.

  17. Casting the Die before the Die Is Cast: The Importance of the Home Numeracy Environment for Preschool Children

    Niklas, Frank; Schneider, Wolfgang

    2014-01-01

    Mathematical competencies are important not only for academic achievement at school but also for professional success later in life. Although we know a lot about the impact of "Home Literacy Environment" on the development of early linguistic competencies, research on "Home Numeracy Environment" (HNE) and the assessment of its…

  18. Casting Footprints for Eternity

    1999-01-01

    Apollo 11 Astronaut Buzz Aldrin has his footprints casted during the dedication ceremony of the rocket fountain at Building 4200 at Marshall Space Flight Center. The casts of Aldrin's footprints will be placed in the newly constructed Von Braun courtyard representing the accomplishments of the Apollo 11 lunar landing.

  19. Old soldiers never die ...

    Boomsma, Jacobus Jan; Nygaard, Sanne

    2012-01-01

    An ancestral supersoldier phenotype of Pheidole ants can be recovered when selection for supersoldiers re-emerges, indicating that the developmental potential for caste pathways is retained.......An ancestral supersoldier phenotype of Pheidole ants can be recovered when selection for supersoldiers re-emerges, indicating that the developmental potential for caste pathways is retained....

  20. Die Erfindung des Manuskripts

    Benne, Christian

    Die Entstehung der literarischen Moderne ging seit dem 18. Jahrhundert damit einher, dass die Anzahl literarischer Manuskripte ebenso wuchs wie deren Bedeutung. Der Buchdruck hatte die Handschrift keineswegs überflüssig gemacht, sondern provozierte im Gegenteil einen neuen, am Autographen...

  1. Multi-layers castings

    J. Szajnar

    2010-01-01

    Full Text Available In paper is presented the possibility of making of multi-layers cast steel castings in result of connection of casting and welding coating technologies. First layer was composite surface layer on the basis of Fe-Cr-C alloy, which was put directly in founding process of cast carbon steel 200–450 with use of preparation of mould cavity method. Second layer were padding welds, which were put with use of TIG – Tungsten Inert Gas surfacing by welding technology with filler on Ni matrix, Ni and Co matrix with wolfram carbides WC and on the basis on Fe-Cr-C alloy, which has the same chemical composition with alloy, which was used for making of composite surface layer. Usability for industrial applications of surface layers of castings were estimated by criterion of hardness and abrasive wear resistance of type metal-mineral.

  2. Die begrafnisdíens

    Num 20: 1; Jos 24: 30; Hand 5: 5 - 11). Selfs van die ... Gebruike rondom die begrafnis het van geslag tot geslag gewissel. De Vaux ... der geskied deur die hoorders 'te onderrig, te vermaan, te vertroos en te bestraf, soos dit in elke geval ..... gehandhaaf hoef te word, veral in die lig van die feit dat die predikant die kerklike.

  3. Die gebruik van parallelplaatreologie vir die bepaling van die intrinsieke viskositeit van poli-etileentereftalaat

    O. C. Vorster

    2005-09-01

    Full Text Available Die bepaling van die intrinsieke viskositeit van poli-etileentereftalaat word bemoeilik deur die feit dat daar tans slegs twee metodes in gebruik is. In die eerste metode word die bepaling deur middel van oplossingsviskometrie gedoen, maar die toksisiteit van die oplosmiddel, asook die tydperk wat dit neem om die bepaling te doen, is ’n probleem. Die tweede metode word beperk deur die kompleksiteit en beskikbaarheid van die apparatuur in Suid-Afrika. In hierdie studie word ’n alternatiewe metode, gebaseer op parallelplaatreologie, voorgestel wat albei hierdie probleme oorkom en die resultate sodoende verkry, word vergelyk met dié wat met bestaande metodes verkry is.

  4. Die invloed van die neo-marxistiese kultuuranalise op die Wêreldraad van Kerke en die Gereformeerde Kerke van Nederland

    J. M. Vorster

    1979-05-01

    Full Text Available Toe die studente dwarsoor die VSA en Europa in die laat sestigerjare ’n plotselinge en radikale verset openbaar het teen die bestaande orde, het hulle die deur geopen vir ’n nuwe mededinger om die hart van die Westerse kultuur. Dit is die nou reeds bekende neo-Marxisme. Sedertdien het hierdie jongeling sy voetspore op vele vlakke van die Westerse kultuur gelaat.

  5. Caste in Itself, Caste and Class, or Caste in Class

    Ramkrishna Mukherjee

    2015-08-01

    Full Text Available After the British conquered Bengal and eventually the whole of India,they set out to administer the colony. In this context they encountered two phenomena with which they were not familiar: (1 the relation of people to land for production (and not for revenue receiving, household living, etc., and (2 the caste system of India, viz. the jati strati?cation of society.

  6. Rubber molds for investment casting

    Sibtain, S.N.

    2011-01-01

    The main objective of the project is to investigate different types of molding rubbers used for investment casting. The level of shape complexity which can be achieved by using these rubber molds is also studied. It was almost impossible to make complex shapes molds using metal molds, in that cases rubber molds are very important because they arc flexible and give accurate and precise part dimensions. Turbine blades are hi-tech components with air-foil geometries that have close dimensional tolerances. They are made of super-alloys and manufactured by investment casting. The final blade profile depends upon the dimensional accuracy in each of the processing steps. In the present work experimental study for the production of high quality low cost castings of turbine blades using rubber molds and injected wax patterns is presented. Natural Rubber molds and wax patterns from these molds were made. Different types of molding rubbers were studied including natural rubber, silicone rubber and liquid silicone rubber. It was found that by using rubber molds we can make most complex shape with very less finishing required. The shrinkage was 12% as compared to original master pattern. Rubber molds were made using laboratory hot press. Three layers of rubber above and below the master pattern. After that vulcanization was done by giving temperature and pressure. (author)

  7. Application of optical scanning for measurements of castings and cores

    M. Wieczorowski

    2010-01-01

    Full Text Available In the paper application of non destructive method for dimensional control of elements in initial phase of car manufacturing, at Volks-wagen Poznań foundry was presented. VW foundry in Poznań is responsible of series production of chill and dies castings made of light alloys using contemporary technologies. Castings have a complex shape: they are die castings of housings for steering columns and gravity chill castings of cylinder heads, for which cores are manufactured using both hot box and cold box method. Manufacturing capabilities of VW foundry in Poznań reach 26.000 tons of aluminum castings per year. Optical system ATOS at Volkswagen Poznań foundry is used to digitize object and determination of all dimensions and shapes of inspected object. This technology is applied in car industry, reverse engineering, quality analysis and control and to solve many similar tasks. System is based on triangulation: sensor head projects different fringes patterns onto a measured object while scanner observes their trajectories using two cameras. Basing on optical transform equations a processing unit automatically and with a great accuracy calculates 3D coordinates for every pixel of camera. Depending on camera reso-lution as an effect of such a scan we obtain a cloud of up to 4 million points for every single measurement. In the paper examples of di-mensional analysis regarding castings and cores were presented.

  8. die pers as bron oor die geskiedenis van die eerste vrydeidsoorlog

    dood agv wonde wat hy tydens die slag opgedoen het. Dit was vir die Britse volk onaanvaarbaar dat slegs twee Boere gedood is nadat daar tussen. 20 000 en 30 000 rondtes op die Boere afgevuur is. Die pers kon net nie die ware syfers publiseer nie, want dit sou na 'n onwaarheid Iyk. Het die. Britse volk egter die Boere ...

  9. die impak van metodologie op die verstaan van die nuwe testament

    voorbeeld eers een maal deur die bril van die vorm- en redaksiekritiek na die Evangelies gekyk het, dink jy vir altyd anders oor hulle tot- standkoming. Inderdaad, nuwe metodes lei tot nuwe perspektiewe! Dit is dan ook waar die fokus van hierdie artikel val: die impak van metodologie op die verstaan van die Nuwe ...

  10. Verskuiwing in die moraal?

    S.P. van der Walt

    1974-03-01

    Full Text Available Modewoorde het ons deesdae oorgenoeg in die Christelike sedeleer en hulle kan nogal verwarring stig. U moet my vergun om met u te spreek oor een so ’n modewoord nl „verskuiwing’’ in die moraal. Dis nogal ’n mooi woord, wat so dikwels gebruik word op baie terreine en tog meer wil aandui as maar net ’n veranderde sienswyse, ’n wysiging in opvattinge of nuwe riglyne wat al gangbaar geword het in die praktyk. Die begrip wil eintlik die ewolusionêre gang beklemtoon, want dit is dan eintlik net die ou norme wat effens anders bekyk word of nie meer so nou geneem of dik onderstreep word nie. Die verskuiwing beteken dan dat alles nog dieselfde bly, net die posisie of plek het verander. Verskuiwing beteken tog plekverandering of plekwisseling en dan sekerlik nie in die sin dat die plekke ver uitmekaar lê nie. Verskuiwing beteken net maar vlak langs die vorige te staan kom. As dit dan ’n beter plek is, is dit ewolusie, ontwikkeling, verbetering.

  11. Laser surface treatment of grey cast iron for automotive applications

    Ocelik, V.; Tang, P.N.; de Boer, M.C.; de Oliveira, U.; de Hosson, J.T.M.; DeHosson, JTM; Brebbia, CA; Nishida, SI

    2005-01-01

    The surface of pearlitic grey cast iron was treated using a 2 kW Nd:YAG laser beam with the final aim to improve its surface properties, mainly for automotive applications. Two kinds of laser surface treatments were experimentally applied. In the laser surface hardening approach the surface of cast

  12. Development of service-relevant materials data and economic quality assurance and machining procedures for gas turbine blades. Final report; Entwicklung betriebsrelevanter Werkstoffkennwerte und wirtschaftlicher Qualitaetssicherungs- und Bearbeitungsverfahren fuer GT-Schaufeln. Schlussbericht

    Buergel, R.; Rechtenbacher, H.

    1994-01-01

    In the frame of the reported project, together with the programme partners, optimization of service relevant properties as well as modification of manufacturing procedures for the forged alloy Nimonic 101 were achieved. These results are directly implementable into serial production and cause improved service reliability and economic benefit. For the forged alloy Udimet 720 materials data were generated in accordance with the programme plan. The final evaluation for this alloy will be performed by the project partner Siemens-KWU. The qualification of fine-grained investment cast blades of IN 792 for large rear=stage blading is not yet fully completed. Three major questions are lacking final answers: - Does a stress rupture strength advantage exist over the forged alloy Udimet 720/coarse/grained? - Can a high cycle fatigue strength as high as that for Udimet 720/coarse-grained be met reproducibly? - Does the investment cast blades offer a cost advantage over the forged ones - technical qualification assumed? The programme helped significantly in preparing the right answers to these questions. (orig.) [Deutsch] Im Rahmen des berichteten Teilvorhabens ist es in Zusammenarbeit mit den Projektpartnern gelungen, fuer die Schmiedelegierung Nimonic 101 die betriebsrelevanten Eigenschaften zu optimieren, sowie die Schaufelherstellung so zu modifizieren, dass die Betriebszuverlaessigkeit verbessert wird. Diese Ergebnisse sind direkt in die Serienfertigung implementierbar und damit wirtschaftlich nutzbar. Fuer die Schmiedelegierung Udimet 720 wurden im Rahmen des Projektverbundes Werkstoffkennwerte ermittelt. Die Gesamtauswertung fuer diesen Werkstoff erfolgt von Projektpartner Siemens-KWU. Das Bild zur Qualifikation feinkoerniger Feingussschaufeln ist noch nicht restlos klar. Drei wesentliche, noch abschliessend zu beantwortende Fragen sind: - Ergibt sich ein Zeitstandfestigkeitsvorteil gegenueber der Schmiedelegierung Udimet 720/Grobkorn? - Laesst sich reproduzierbar eine

  13. Evaluation of Cracking Causes of AlSi5Cu3 Alloy Castings

    Eperješi Š.

    2014-10-01

    Full Text Available Recently, the castings made from aluminum-silicon alloys by pressure die casting are increasingly used in the automotive industry. In practice, on these castings are high demands, mainly demands on quality of their structure, operating life and safety ensuring of their utilization. The AlSi5Cu3 alloy castings are widely used for production of car components. After the prescribed tests, the cracks and low mechanical properties have been identified for several castings of this alloy, which were produced by low pressure casting into a metal mould and subsequent they were heat treated. Therefore, analyses of the castings were realized to determine the causes of these defects. Evaluation of structure of the AlSi5Cu3 alloy and causes of failure were the subjects of investigation presented in this article.

  14. 75 FR 20387 - Contech Castings, LLC, Including Workers Whose Unemployment Insurance (UI) Wages Are Reported...

    2010-04-19

    ... Apply for Worker Adjustment Assistance In accordance with Section 223 of the Trade Act of 1974, as... aluminum and magnesium die casted component parts for automobiles. New information shows that the assets of... workers of the subject firm who were adversely affected by increased imports of aluminum and magnesium die...

  15. CASTING METHOD AND APPARATUS

    Gray, C.F.; Thompson, R.H.

    1958-10-01

    An improved apparatus for the melting and casting of uranium is described. A vacuum chamber is positioned over the casting mold and connected thereto, and a rod to pierce the oxide skin of the molten uranium is fitted into the bottom of the melting chamber. The entire apparatus is surrounded by a jacket, and operations are conducted under a vacuum. The improvement in this apparatus lies in the fact that the top of the melting chamber is fitted with a plunger which allows squeezing of the oxide skin to force out any molten uranium remaining after the skin has been broken and the molten charge has been cast.

  16. Symptomatic stent cast.

    Keohane, John

    2012-02-03

    Biliary stent occlusion is a major complication of endoscopic stent insertion and results in repeat procedures. Various theories as to the etiology have been proposed, the most frequently studied is the attachment of gram negative bacteria within the stent. Several studies have shown prolongation of stent patency with antibiotic prophylaxis. We report the case of stent occlusion from a cast of a previously inserted straight biliary stent; a "stent cast" in an 86-year-old woman with obstructive jaundice. This was retrieved with the lithotrypter and she made an uneventful recovery. This is the first reported case of a biliary stent cast.

  17. oor die inhoud en boodskap van die heidelbergse kategismus

    Smit. Oor die Inhoud en Boodskap van die Heidelbergse Kategismus. 52. Uiteraard sal dié tema saamhang met die bedoelinge agter die opstel van die Kategismus. Ook die vraag na moontlike bedoelinge of motiewe is egter 'n ingewikkelder vraag as wat miskien gedink mag word. Uiteraard was daar agter elke kategismus ...

  18. Thomas Erastus oor die struktuur van die gemeenskap'^

    óók aansprake en regte het, is die opvatting dat sowel die burgerlike gemeenskap as die kerk 'n perfecta societas sibi sufficiens is, nié werklik aanvaar nie. Die Middeleeuse gemeenskap was die corpus christianum,. 'n gemeenskap wat nie deur fisiese of politieke grense beperk was nie. Sy grense het gelê waar die grense ...

  19. die doel en wese van opvoedende onderwys en die implikasies

    Oaar moet onderskei word tussen die doelstellings van opvoedende onderwys en die einddoel wat bereik word deur die nastrewing van hierdie doelstellings. Gunter praat van die naderliggende doelstellings (1981, b1.105). \\/at die enddoel van opvoedende onderwys bet ref, gaan die meeste opvoedkundi ges akkoord dat ...

  20. Die tug oor ampsdraers tydens die doleansie van 1886

    J. Visser

    1986-06-01

    Full Text Available In art 29 van die Nederlandse Geloofsbelydenis word bely: “Die merktekens om die ware Kerk te ken is die volgende: As die Kerk die suiwere prediking van die evangelie uitoefen, as dit die suiwer bediening van die sakramente gebruik soos Christus dit ingestel het, as die kerklike tug gebruik word om die sondes te straf.” Dit spreek vanself dat wanneer ampsdraers, aan wie Christus sy kudde toevertrou het (Hand 20 : 28, met leer en /of lewenswandel in sonde volhard en nie daarin met tug gestuit word nie, word die ware kerk nie gebou nie maar afgebreek. 0ns sal later in hierdie artikel aantoon hoedanig die suiwer tug oor ampsdraers, veral leertug, tydens die Doleansie tot skade van die kerk van Christus agterweë gebly het.

  1. Rapidly cast crystalline thin sheet materials

    Warlimont, H.; Emmerich, K.

    1986-01-01

    The current state and progress of casting thin sheet and ribbons directly from the melt are reviewed. First, the solidification phenomena pertinent to the process are outlined. Subsequently, Fe-Si,l Fe-Si-Al, Fe-Nd-B, Ag-Cu-Ti, alloy steels, Ni superalloys and Si are treated as examples. Finally, the information available on process development is critically assessed

  2. Bainite obtaining in cast iron with carbides castings

    S. Pietrowski

    2010-01-01

    Full Text Available In these paper the possibility of upper and lower bainite obtaining in cast iron with carbides castings are presented. Conditions, when in cast iron with carbides castings during continuous free air cooling austenite transformation to upper bainite or its mixture with lower bainte proceeds, have been given. A mechanism of this transformation has been given, Si, Ni, Mn and Mo distribution in the eutectic cell has been tested and hardness of tested castings has been determined.

  3. Die metafoor by Breyten Breytenbach

    Owner

    23 Jun 2009 ... metafories, of spesifiek verwysend, te werk gegaan is. Tyd sou mens die hoofmotief van die bundel noem, tyd en geheue wat verbygaan: 1 en 2; en die einde van die storie wat gekom het: “fluit-fluit my storie is uit”. (Die tema van verbygaan word weer opgeneem in 8 en 9: die stories wat nooit meer gehoor ...

  4. IRAN IN DIE INTERNASIONALE MAGSTRYD

    In die verband kan genoem word dat die Russe nog grotendeels gebruik maak van 'n metode waarvolgens water in die oliestratum gepomp word om 'n opwaartse druk van ru-olie te verseker; een nadeel hiervan is dat die water mettertyd deur die oliehoudende laag ontsnap en agv die drukverlies isvoortgesette ontginning.

  5. Low Cost Al-Si Casting Alloy As In-Situ Composite for High Temperature Applications

    Lee, Jonathan A.

    2000-01-01

    A new aluminum-silicon (Al-Si) alloy has been successfully developed at NASA- Marshall Space Flight Center (MSFC) that has significant improvement in tensile and fatigue strength at elevated temperatures (500 F-700 F). The alloy offers a number of benefits such as light weight, high hardness, low thermal expansion and high surface wear resistance. In hypereutectic form, this alloy is considered as an in-situ Al-Si composite with tensile strength of about 90% higher than the auto industry 390 alloy at 600 F. This composite is very economically produced by using either conventional permanent steel molds or die casting. The projected material cost is less than $0.90 per pound, and automotive components such as pistons can be cast for high production rate using conventional casting techniques with a low and fully accounted cost. Key Words: Metal matrix composites, In-situ composite, aluminum-silicon alloy, hypereutectic alloy, permanent mold casting, die casting.

  6. Die singulation method

    Swiler, Thomas P.; Garcia, Ernest J.; Francis, Kathryn M.

    2013-06-11

    A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with an HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

  7. Multiscale modeling for the prediction of casting defects in investment cast aluminum alloys

    Hamilton, R.W.; See, D.; Butler, S.; Lee, P.D.

    2003-01-01

    Macroscopic modeling of heat transfer and fluid flow is now routinely used for the prediction of macroscopic defects in castings, while microscopic models are used to investigate the effects of alloy changes on typical microstructures. By combining these two levels of modeling it is possible to simulate the casting process over a wider range of spatial and temporal scales. This paper presents a multiscale model where micromodels for dendrite arm spacing and microporosity are incorporated into a macromodel of heat transfer and in order to predict the as cast microstructure and prevalence of microscopic defects, specifically porosity. The approach is applied to aluminum alloy (L169) investment castings. The models are compared with results obtained by optical image analysis of prepared slices, and X-ray tomography of volume samples from the experiments. Multiscale modeling is shown to provide the designer with a useful tool to improve the properties of the final casting by testing how altering the casting process affects the final microstructure including porosity

  8. Casting AISI 316 steel by gel cast

    Ozols, A; Thern, G; Rozenberg, S; Barreiro, M; Marajofsky, A

    2004-01-01

    The feasibility of producing AISI 316 steel components from their powders and avoiding their compaction is analyzed. A casting technique is tested that is similar to gel casting, used for ceramic materials. In the initial stage, the process consists of the formulation of a concentrated barbotine of powdered metal in a solution of water soluble organic monomers, which is cast in a mold and polymerized in situ to form a raw piece in the shape of the cavity. The process can be performed under controlled conditions using barbotines with a high monomer content from the acrylimide family. Then, the molded piece is slowly heated until the polymer is eliminated, and it is sintered at temperatures of 1160 o C to 1300 o C under a dry hydrogen atmosphere, until the desired densities are attained. The density and micro structure of the materials obtained are compared with those for the materials compacted and synthesized by the conventional processes. The preliminary results show the feasibility of the process for the production of certain kinds of structural components (CW)

  9. Ontsporing van die regstaatsbegrip en sy konsekwensies vir die afrikanervolk

    N. G.S. Van der Walt

    1966-03-01

    Full Text Available Die opvatting van die suiwere regstaat bring sy vraagstukke mee wanneer dit in verband gebring word met die leer van die soewereiniteit in eie kring. Laasgenoemde leer wortel in die geloof dat God die mens roep tot diens aan Hom, en dat die mens vry moet wees om ten opsigte van alle lewensaspekte God na die hoogste mate te kan dien. Hierdie verskeidenheid van aspekte is deur dr. A. Kuyper en sy volgelinge gesistemati- seer tot menslike verbande en lewenskringe, elk met ’n be- paalde sfeer waarin ander kringe nie mag inmeng nie. Elkeen is dan soewerein binne sy eie kring. Met verwysing na die staat is dan gespreek van die staatstaak as synde die hand- hawing van die reg, en omdat die staat in toenemende mate hom veral in die latere tyd ook besig gehou het met bedrywig- hede wat nouliks as van juridiese aard beskou kan word, is daar die onderskeid gemaak tussen die primêre en sekundêre taak van die staat. Die sistematiek van die wetsidee, deur prof. Dooyeweerd ontwikkel, waar die staat sy bestemmingsfunksie in die regsaspek vind, het vanselfsprekend geen plek vir so 'n dualistiese staatstaak nie, en die oplossing is deur sommige daarin gesoek om sulke staatsoptrede te vertolk as hebbende wel betrekking op die regsgemeenskap of die regsverkeer. Staatsondernemings soos paaie, spoorweë, spellingreëling, ens. word dan beskou as noodsaaklik vir die instandhouding van die regsgemeenskap en regsverkeer. Tereg wys A. M. Donner1 daarop dat so ’n vertolking eintlik neerkom op ’n oorspanning van die regsbegrip. Hy self sien dan die staatstaak in vrede- of orde-handhawing, wat in die eerste plaas wel regshandha- wing veronderstel. Onder orde word dan alles verstaan wat noodsaaklik is vir die gladde verkeer in die ontwikkelingsgang van die regsgemeenskap. Die wese van die staat het dan vol- gens hom te doen met reg, maar sy taak is meer as suiwere regshandhawing. Wat onrus verwek en die orde versteur, moet uit die openbare lewe verwyder word, en die

  10. Die sterwende kindjie

    J.T. De Jongh van Arkel

    1983-09-01

    Full Text Available The thought of a child dying appears as an antithesis and thus the feelings evoked by the dying child are stronger than when older persons are dying. Around the child’s death bed there is no place for detached spectators and all become involved in caring for and supporting him. Caregivers also have a supporting responsibility towards the members of the child’s family.

  11. Analise van die Tswanaraaisel

    S. A. Swanepoel

    1984-05-01

    Full Text Available ’n Strukturele, stilistiese en funksionele bcskrywing van die Twanaraaisel bring mee dat daar aan die volgende aspekte aandag gegee moet word: •\tWat is ’n raaisel en lioe word dit in Tswana genoem. •\tTot watter studiegebied en literere genre hoort die raaisel en watter subvorme kan vir Tswana onderskei word. •\tHoe sien die struktuur van Tswanaraaisels daar uit. •\tDeur wie, waar, wanneer en hoe word Tswanaraaisels voorgedra. •\tWatter stilistiese kenmcrke kan in Tswanaraaisels onderskei word. •\tWatter funksies vervul raaisels in ’n Tswanagcmeenskap.

  12. The Angry Dying Patient.

    Houston, Robert E.

    1999-02-01

    Over 25 years ago, Kubler-Ross identified anger as a predictable part of the dying process. When the dying patient becomes angry in the clinical setting, all types of communication become strained. Physicians can help the angry dying patient through this difficult time by using 10 rules of engagement. When physicians engage and empathize with these patients, they improve the patient's response to pain and they reduce patient suffering. When physicians educate patients on their normal responses to dying and enlist them in the process of family reconciliation, they can impact the end-of-life experience in a positive way.

  13. Die brein soos beskou deur die Grieke en Romeine

    Francois P. Retief

    2015-02-01

    Full Text Available In Ou Egipte is mummifikasie met uitgebreide reseksie of uitsnyding van organe geassosieer, maar geen kennis is geneem van die morfologie van die brein nie. Griekse skrywers van die sesde en vyfde eeue v.C. het die brein aanvanklik gesien as die setel van intelligensie, die orgaan van sensoriese waarneming en gedeeltelik die oorsprong van sperma. Pneuma het ’n belangrike rol in breinfunksie gespeel. Hippokrates was die eerste om die brein te beskryf as ’n dubbele orgaan, wat met harsingvlies (meninges bedek, funksioneel van pneuma afhanklik en vertolker van begrip is. Tydgenote soos Plato, Aristoteles en Diokles het tot die beskrywing bygedra, maar laasgenoemde twee het beweer dat die hart die middelpunt van intelligensie is en nie die brein nie. Gedurende die laaste helfte van die vierde eeu v.C. is disseksie van die menslike liggaam tydelik aan die mediese skool van Alexandrië toegelaat en het dit tot merkwaardige vooruitgang in die begrip van die menslike anatomie en fisiologie gelei. Herofilus en Erasistratus het uitstekende beskrywings van die struktuur en funksie van die brein gegee wat eers in die tweede eeu n.C. deur Galenus geëwenaar is.

  14. DIE SUID-AFRIKAANSE JEUG IN VOORTREKKERTYDPERK

    dien. Die planke en velie moes keer dat die assegaaie die mense tref. Voor die geveg het die vrouens en groter dogters koeels gegiet. Tydens die geveg het die seuns gehelp skiet terwyl die vrouens en dogters die gewere vir die mans gelaai het. Van die dogters soos Nellie. Botha (11 jaar oud) en haar sussie Fya (15 jaar.

  15. Process development for utilizing asbestos cement waste in rotary kilns for the cement industry. Final report; Erarbeitung eines Verfahrens zur stofflichen Verwertung von zementgebundenen Asbestprodukten in Drehrohroefen fuer die Zementindustrie. Abschlussbericht

    Schlegel, R.; Kieser, J.; Kraehner, A.

    1999-11-01

    The law for recycling and waste demands the utilization also for waste of asbestos cement (ac). The procedure of thermal utilization of ac in the flame of a rotary cement kiln was developed and patented by the research institute IBU-tec Weimar, Germany. The ac-material has to be pre-pulverized and grinded to a degree of fineness of R{sub 90}<15%. Considerations of safety engineering lead to the idea of common fine grinding of old oil (oo) and ac. This new procedure was searched in FuE-project in 1998/99 (financial support by BMBF). A mash of ac and oo was generated as a utilization product ready for firing which was injected into the flame of the rotary cement kiln. This particles of ac smelt to spherical shaped particles at a temperature above 1500 C. They were utilized by clinker formation. The material and gas stream leaving the kiln does not contain fibres of asbestos. This was demonstrated in a small equipment burning test. The industrial realization concerning cement plant Ruedersdorf, near Berlin, was searched, technologically described and safety engineeringly and financially assessed by a project study. Process-technical and financial advantages were seen for the dry fine grinding. The wet fine grinding with old oil could be used in cement plants using old oil as fuel. (orig.) [German] Das Kreislaufwirtschafts- und Abfallgesetz (1994) fordert u.a. die stoffliche Verwertung auch fuer Asbestzementabfaelle (AZ). Das vom Institut fuer Baustoff- und Umweltschutz-Technologie Weimar 1995 entwickelte und patentierte Verfahren zur thermischen Verwertung von AZ in der Flamme eines Zementdrehrohrofens erfuellt diese Forderung. Das AZ-Material muss vorzerkleinert und bis zur Rohmehlfeinheit (R{sub 90}<15%) feingemahlen werden. Sicherheitstechnische Ueberlegungen fuehrten zu der Idee, die Feinmahlung zusammen mit Altoel (AOe) zu erproben. Diese Verfahrensvariante wurde im Rahmen eines FuE-Projektes 1998/99 untersucht (finanzielle Foerderung durch das BMBF). Als

  16. Study on Manufacturing Process of Hollow Main Shaft by Open Die Forging

    Kwon, Yong Chul; Kang, Jong Hun; Kim, Sang Sik

    2016-01-01

    The main shaft is one of the key components connecting the rotor hub and gear box of a wind power generator. Typically, main shafts are manufactured by open die forging method. However, the main shaft for large MW class wind generators is designed to be hollow in order to reduce the weight. Additionally, the main shafts are manufactured by a casting process. This study aims to develop a manufacturing process for hollow main shafts by the open die forging method. The design of a forging process for a solid main shaft and hollow shaft was prepared by an open die forging process design scheme. Finite element analyses were performed to obtain the flow stress by a hot compression test at different temperature and strain rates. The control parameters of each forging process, such as temperature and effective strain, were obtained and compared to predict the suitability of the hollow main shaft forging process. Finally, high productivity reflecting material utilization ratio, internal quality, shape, and dimension was verified by the prototypes manufactured by the proposed forging process for hollow main shafts

  17. Study on Manufacturing Process of Hollow Main Shaft by Open Die Forging

    Kwon, Yong Chul [Gyeongnam Technopark, Changwon (Korea, Republic of); Kang, Jong Hun [Jungwon Univ., Goisan (Korea, Republic of); Kim, Sang Sik [Gyeongsang Natiional Univ., Jinju (Korea, Republic of)

    2016-02-15

    The main shaft is one of the key components connecting the rotor hub and gear box of a wind power generator. Typically, main shafts are manufactured by open die forging method. However, the main shaft for large MW class wind generators is designed to be hollow in order to reduce the weight. Additionally, the main shafts are manufactured by a casting process. This study aims to develop a manufacturing process for hollow main shafts by the open die forging method. The design of a forging process for a solid main shaft and hollow shaft was prepared by an open die forging process design scheme. Finite element analyses were performed to obtain the flow stress by a hot compression test at different temperature and strain rates. The control parameters of each forging process, such as temperature and effective strain, were obtained and compared to predict the suitability of the hollow main shaft forging process. Finally, high productivity reflecting material utilization ratio, internal quality, shape, and dimension was verified by the prototypes manufactured by the proposed forging process for hollow main shafts.

  18. Die uitbouing van die Bybelse kanon in antieke Judaïsme en die ...

    31 Jul 2015 ... die oer-Christelike boodskap tot by sy Ou Testamentiese wortels, die geskrifte van Israel wat cum grano salis die 'Bybel' van die oer-Christendom geword het en die blywende verwysingspunt van die Christelike boodskap is. Erkenning. Hierdie artikel is vertaal na Afrikaans deur Prof. Jan G. van der Watt.

  19. Die opleiding van bedryfsielkundiges aan die universiteit van Fort Hare

    W. Botha

    1977-11-01

    Full Text Available Die Departement Bedryfsielkunde aan die Universiteit van Fort Hare is 'n relatiewe jong departement en het eers in 1965 tot stand gekom. Voor hierdie datum is Bedryfsielkunde as 'n kort kursus deur die departement van suiwer Sielkunde aangebied en een van die destydse dosente, Dr. W. Backer, het die inisiatief geneem om 'n selfstandige departement van Bedryfsielkunde in die Fakulteit van Ekonomiese Wetenskappe op die been te bring.

  20. Oor die Bybel in die Afrikaanse digkuns

    another. As a matter of fact, the development of Afri kaans, the instrument of the poet, has been significantly influenced the Afrikaans translation of the Bible. Belie ... ook gesê het: Saam met ons literatuur, so oud as hy is. Die eerste Afrikaanse digter by wie ons omvattende Bybelse invloed kry, is. Totius, een van ons vroegste ...

  1. calvyn oor die leiding van die heilige gees in die verklaring van die

    Mittel alters, bis er zur Ruhe kommt bei den kanonischen Schriften der. Urzeit der christlichen Ära (Barth ... (ego tamen dimoveri non possum ab amore compendii, CO 10, 403). Deur die boodskap van die .... Idem ergo spiritus qui per os prophetarum loquutus est, in corda nostra penetret necesse est, ut persuadeat fideliter ...

  2. KERKWEES IN DIE

    Acta Theologica is an accredited South. African journal publishing ... SciELO South Africa. REDAKSIE/ ... 'n persoon belydenis van geloof af wat instemming met die betrokke kerk se ...... Ek was na my ongeluk buite aksie en op Clarens. 'n Mede-lid ...... Die “formation of new confessions, change to current confessions, and.

  3. Dying with dignity

    S P Kalantri

    2003-01-01

    The concept of dignity has beeen one of the ambiguous concepts in biomedical ethics. Thus the ambiguous nature of this concept has been extended to what it means to die with dignity. This research work is an investigation into the complexity in the understanding of "dying with dignity" in Applied Ethics.

  4. The day Madiba died

    8 Apr 2016 ... shibien en ma is nie happy nie. Susan Gaigher se allegoriese fanta- sie- oftewel wetenskapsfiksieverhale. “Martine se teepot” (46–55) en “Maslow”. (56–67) is verfrissend. Gaigher is een van die min skrywers in die bundel wat 'n kenmerkende en oorspronklike stem laat klink. 'n Mens sal 'n Gaigher-verhaal.

  5. Die entwicklung, die metamorphose, die entstehung: Die konzepte des organismus von Aristoteles bis Darwin

    Kamerer Eva

    2009-01-01

    Full Text Available (nemački In diesem Aufsatz versuche ich, die Elemente verschiedener Konzepte des Organismus in der Philosophie und in der Wissenschaft zu analysieren. Die Deutungen des Organismus und der Einheit der Natur bei Aristoteles, Kant und Goethe werden als ein Beispiel der Bewegung von einem finalistischen zum antifinalistischen Bild der Natur verstanden.

  6. Paradigmas en progressie in die teologie: *n Perspektief op die ...

    Die metodologie as besinningsterrein word egter al belangriker. Gedurende die tweede week van April 1988 het teoloë van dwarsoor Suid-. Afrika by die nuwe gebou van die Raad vir Geesteswetenskaplike Navorsing in. Pretoria byeen gekom vir 'n kongres van amper drie dae met die tema Paradigma.'> 476. ISSN 0259 ...

  7. die korrelasie tussen die gemiddelde daaglikse toename van ...

    'n Regressielyn is uit die gegewens bereken deur 'n beswaarde regressieanaliese en die 80 persent-voorspellings- bande is bepaal. Die punte wat ver buite die normale ver- spreidingsband geval hetkon almal met goeie rede as abnor- maal beskou word (sien tabel 1) en is nie ingesluit by die statistiese berekenings nie.

  8. amp' van die ouderling in die Nuwe Testament

    Jesus self het geen kerk gestig nie en daarom, veral omdat die Jesus-beweging inter mums ten opsigte van die Joodse godsdiens van sy tyd tot stand gekom het, het ...... Die klem val dus nie op die npoTCTT0fievo<; se rang of outoriteit nie, maar op sy pastorale funksie in die huishouding of huisgemeente (kyk Reicke.

  9. Development of a regional concept for energy management for the region of Karlsruhe. Final report; Entwicklung eines regionalen Energiemanagement-Konzeptes und Anwendung auf die TechnologieRegion Karlsruhe. Endbericht

    Rentz, O.; Fichtner, W.; Frank, M. [Karlsruhe Univ. (T.H.) (Germany). Inst. fuer Industriebetriebslehre und Industrielle Produktion; Wolf, M.A.; Rejman, M.; Eyerer, P. [Fraunhofer-Institut fuer Chemische Technologie (ICT) (Germany); Reimert, R.; Schulz, A.; Buren, V. v. [Karlsruhe Univ. (T.H.) (Germany). Engler-Bunte-Institut Bereich 1 - Gas, Erdoel und Kohle; Schaefers, B.; Bernart, Y. [Karlsruhe Univ. (T.H.) (DE). Institut fuer Soziologie (IfSoz) (Germany)

    2002-09-01

    Major objectives of this project are: to prepare a cross-disciplinary analysis of all characteristic aspects of the energy supply and demand patterns of a group of selected energy-intensive companies in the Karlsruhe and Rhine harbour area (5 industrial power consumers, 1 utility), to identify practical approaches for optimization and integration of energy and material flows, (networking), and to develop optimised investment and energy supply options within the framework of given conditions. The basis of the optimal solution and energy network presented and explained in detail is a new combined-cycle power plant running as a gas-fired CHP plant, substituting about 50% of the systems formerly used. (orig./CB) [German] Fragestellungen der Effizienzsteigerung und der Verwertung von Abfaellen und Abwaerme gewinnen an Relevanz vor dem Hintergrund der begrenzten Aufnahmekapazitaet der Umweltmedien fuer Schadstoffe. Im Rahmen des Projektes wurde am Beispiel der Region Karlsruhe (5 Industrieunternehmen und 1 EVU) die Entwicklung betriebsuebergreifender Energieversorgungssysteme (Netzwerke) interdisziplinaer analysiert und beschrieben. Zielsetzungen des Projekts waren unter anderem: Bestimmung von zukunftsfaehigen Optionen, intelligente Vernetzung von Energiestroemen, wirtschaftliche Optimierung betriebsuebergreifender Energiemanagement-Loesungen. Die optimale vorgestellte Loesung ist charakterisiert durch den Neubau einer zentralen, gasgefeuerten GuD-Anlage, die etwa die Haelfte der bisherigen Anlagen ersetzt und zusammen mit den weiterhin genutzten Anlagen die Energieversorgung der Unternehmen sicherstellt. (orig./CB)

  10. Die toekoms en ons roeping

    S. du Toit

    1954-03-01

    Full Text Available Om te weet wat ons roeping in die toekoms sal wees, moet ons eers besef wat in ons eie tyd aan die gang is en langs watter lyne die dinge beweeg. Dit is ons plig om te let op die tekens van die tye in die lig van die profetiese Woord. En dan wil ons dadelik beklemtoon dat ons in Suid-Afrika nie in die waan moet lewe dat ons hier onbekommerd en onaangetas deur die wêreldgebeure ons roeping en bestemming kan uitwerk nie.

  11. Die Hervormde Teologiese Studies na vyftig jaar

    INLEIDEND. In die tweede helfte van die jaar 1943 het die Hervormde Teologiese Studies die eerste maal verskyn. Dit was die produk van lang besinning en beplanning. Die dryfkrag agter die totstandkoming was prof dr S P Engeibrecht, 'n man wie se idealisme en toewyding aan die kerk groot dinge vir die kerk en ook die ...

  12. Cast iron components for the wind power industry. Development of resource saving products and processes in global competition. Final report; Gjutgods till vindkraftsindustrin. Utveckling av resurssnaala produkter och processer i global konkurrens. Slutrapport

    Gustavsson, Conny; Gustafsson, Ingela; Petku, Damir [Swedish Foundry Association, Joenkoeping (SE)] [and others

    2006-01-15

    The demand for large cast components in ductile iron for wind power plants has increased strongly. As wind power plants become larger, today up to 4-5 MW, the components grow with them. Weights around 20 tons become common, and are demanded in growing numbers. For most Swedish foundries production of such size components is impossible, but for a few, accustomed to large castings a new growing market has opened. Higher prices for scrap and electricity is however a menace to profit. This project concentrates on factors that may optimize the flow in production, reduce rejections, reduce the consumption of new sand, and to reduce energy consumption in all processes. The project has resulted in ten separate reports, that are included in this publication.

  13. Die owerheidsinmenging met betrekking tot kerklike tughandelinge.

    L. Roeleveld

    1982-06-01

    Full Text Available Volgens art 29 NGB is die merktekens van die ware kerk die suiwere prediking van die Evangelie, die suiwere bediening van die Sakramente en die gebruik van die kerklike tug. Art. 32 NGB spreek uit dat die Kerkorde nie mag afwyk van wat Christus ingestel het nie. Menslike vindinge en wette om die gewetens te bind en te dwing, moet daarom verwerp word. Die ekskommunikasie of die ban moet toegepas word volgens die Woord van God.

  14. Pentateugtradisies in die boek Hosea

    om te bepaal of die verwysing na 'n gebeure te doen het met die verre verlede of met die .... Hosea 2:1-2 JHWH se trou aan sy beloftes. ... dat huile na Egipte sal terugkeer. Die presiese bedoeiing van die woorde 'huile sal terugkeer na Egipte' is omstre- de. Kommentatore soos Rudolph meen dat dit verstaan moet word as ...

  15. Die begrafnisdíens

    (De Vaux 1961:108). Was die begrafnis 'n familie of 'n kerklike aangeleentheid? Hierdie vraag word nie in die Bybel beantwoord nie. Abraham het sy vrou begrawe (Gen 23: 19-. 20). Isak en Ismael ..... ver gekom om die begrafnis 'n kerklike aangeleentheid te maak nie. Hierdie stap .... trou aan die sorg van God. * Die kerk ...

  16. Metodes in die Christelike etiek

    The basic question in Christian ethics is not primarily. 'What should I do?' The basic question is rather ' ... should therefore be accepted as being part of the method used in Christian ethics. 1. INLEIDEND ..... aan die kant van die onderdrukte' verkondig word, word die Christen opgeroep om horn te skaar aan die kant van die ...

  17. MIOR - Microbial Improved Oil Recovery. Basics studies on the suitability of microorganisms for improved oil recovery. Final report; MIOR - Microbial Improved Oil Recovery. Grundlagen der Eignung von Mikroorganismen fuer die Verbesserung der Erdoelgewinnung. Abschlussbericht

    Naeveke, R. [Technische Univ. Braunschweig (Germany). Inst. fuer Mikrobiologie; Fischer, K. [Technische Univ. Braunschweig (Germany). Inst. fuer Mikrobiologie; Timmis, K.N. [Gesellschaft fuer Biotechnologische Forschung mbH, Braunschweig (Germany); Yakimov, M. [Gesellschaft fuer Biotechnologische Forschung mbH, Braunschweig (Germany); Kroeger, A. [Gesellschaft fuer Biotechnologische Forschung mbH, Braunschweig (Germany); Bosecker, K. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany); Kruckemeyer, I. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany); Mengel-Jung, G. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany); Bock, M. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany); Schink, B. [Konstanz Univ. (Germany). Fachgebiet Mikrobielle Oekologie; Denger, K. [Konstanz Univ. (Germany). Fachgebiet Mikrobielle Oekologie; Kessel, D. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Amro, M. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Jacobs, G. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Hoffmann, G.G. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Wagner, M. [Erdoel - Erdgas Gommern GmbH (Germany); Ziran, B. [Erdoel - Erdgas Gommern GmbH (Germany); Nowak, H.U. [Erdoel - Erdgas Gommern GmbH (Germany); Eins, I. [Erdoel - Erdgas Gommern GmbH (Germany); Rosenspiess, K. [Erdoel - Erdgas Gommern GmbH (Germany); Lungershausen, D. [Erdoel - Erdgas Gommern GmbH (Germany)

    1996-03-01

    . Ziel des Projektes war es, die Anwendbarkeit von MIOR-Verfahren auf Sandsteinlagerstaetten, wie sie in Norddeutschland haeufig vorkommen, zu untersuchen. Aus Proben von Erdoelfoerdersonden, erdoelverarbeitenden Betrieben und oelkontaminierten Boeden wurden Mikroorganismen angereichert, isoliert und charakterisiert. Mit einem Screening wurden ueber 500 Bakterienstaemme auf die Bildung von viskositaetssteigender oder oberflaechenaktiven Substanzen, auf anaerobes Wachstum, auf Halotoleranz und Temperaturtoleranz getestet. Einer weitergehenden Untersuchung wurden 39 ausgewaehlte Staemme unterzogen, aus denen wiederum die Staemme Bacillus licheniformis BNP 29 und Sporohalobacter als besonders MIOR-geeignet eingestuft werden konnten. Um die Entoelungswirksamkeit der Bakterienstaemme zu quantifizieren und Entoelungsmechanismen aufzuklaeren, wurden dynamische Flutversuche unter realen Lagerstaettenbedingungen an Sandsteinkernen durchgefuehrt. Mit Hilfe dieser Versuche konnte nachgewiesen werden, dass die Injizierbarkeit sowie die Migration der Bakterien im poroesen Medium gewaehrleistet sind. Die Bakterienstaemme sind darueber hinaus in der Lage, unter Bedingungen, wie sie in norddeutschen Lagerstaetten auftreten, zu wachsen. Ihr Einsatz bei den Flutversuchen fuehrte zu einer signifikanten Erhoehung des Entoelungsgrades. Als wichtigste Mechanismen, die fuer eine Mehrentoelung verantwortlich sind, wurden die Reduzierung der Permeabilitaet durch das Wachstum der Bakterien im Porenraum und die Aenderung des Benetzungszustandes der Porenwand des Gesteins ermittelt. Durch die Einfuehrung von pH-Puffersubstanzen ist es gelungen, geeignete Naehrmedien fuer die MIOR-Anwendung in Sandsteinlagerstaetten zu entwickeln. (orig.)

  18. Die teologiese skool in die P.U.K vir C.H.O.: met die betekenis van die teologiese skool vir die Christelike wetenskap

    F. Postma

    1944-03-01

    Full Text Available Die Teologiese Skool van die Gereformeerde Kerk gedink op 29 November 1944 sy vyf-en-sewentigjarige bestaan.Die Raad en Senaat van die P.U.K. vir C.H.O. wil ook langs hierdie weg die Teologiese Skool van harte gelukwens en die versekering gee dat daar by die outoriteite van die P.U.K. ’n diepgevoelde dankbaarheid heers dat hierdie inrigting sovele jare deur onse God en Vader gedra en gespaar is.

  19. A comparative evaluation of linear dimensional accuracy of the dies obtained using three conceptually different die systems in the fabrication of implant prosthesis: An in vitro study

    Manawar Ahmad

    2014-01-01

    Purpose: The purpose of the study was to evaluate the linear dimensional accuracy between the implant master die and three conceptually different die systems such as Pindex system, Accu-trac precision die system, and Conventional brass dowel pin system. Materials and Methods: Thirty impressions of implant master die were made with polyether impression material. Ten experimental implant casts were fabricated for each of the three different die systems tested: Accu-trac precision die tray system, Pindex system, and conventional brass dowel pin system. The solid experimental casts were sectioned and then removed from the die system 30 times. Linear distances between all six possible distances were measured from one centre of the transfer coping to the other, using a co-ordinate measuring machine in millimeters up to accuracy of 0.5 microns. Data were tabulated and statistically analyzed by Binomial non parametric test using SPSS version 15. Results: Significant differences were found for distance A-B (P = 0.002, A-C ( P = 0.002, A-D (P value = 0.002, and B-D ( P = 0.021 in Conventional Dowel pin system however for Accu-trac precision die tray system, it was significant only for distance A-D (P = 0.002 but for Pindex system it was non-significant for all the distances measured. Conclusion: Within the limitations of this study, use of Pindex system is recommended when sectioned dies are needed for a multi implant retained prosthesis.

  20. Influence of polyurethane resin dies on the fit and adaptation of full veneer crowns.

    Lillywhite, Graeme R R; Vohra, Fahim

    2015-01-01

    Polyurethane resin is a possible alternative to type IV dental stone for fabrication of indirect restorations however its dimensional accuracy is questionable. The aim was to investigate the dimensional accuracy of silica filled polyurethane resin die material by evaluating the marginal fit and adaptation of indirect gold castings. Experimental, in vitro study. Totally 40 copper plated replicas of a nickel chrome master die analogous to a veneer gold crown preparation were made and impressions recorded using polyvinylsiloxane material. Twenty impressions were poured in type IV dental stone (control group (Vel-mix, Kerr, UK) and the remaining (n = 20) in silica filled polyurethane die material (test group) (Alpha Die MF, CA, USA). Gold castings were fabricated for each die using standardized techniques. The castings were seated on their respective copper plated dies, embedded in resin and sectioned. The specimens were analyzed by measuring marginal opening and the area beneath the casting at a ×63 magnification and using image analysis software. Data were analyzed using a Student's t-test. No significant difference was observed between the experimental groups (P > 0.05). The mean marginal opening for type IV, dental stone and polyurethane resin, was 57 ± 22.6 μm and 63.47 ± 27.1 μm, respectively. Stone displayed a smaller area beneath the casting (31581 ± 16297 μm 2 ) as compared to polyurethane resin (35003 ± 23039 μm 2 ). The fit and adaptation of indirect gold castings made on polyurethane and type IV dental stone dies were comparable.

  1. Die Frage nach Gerechtigkeit.

    Martin Jäggle

    2014-07-01

    Full Text Available ENGLISH: In the first part six stages in the author’s path of life are described, which have influenced his engagement with justice. The second part gives an insight into his religious educational work, in which the issue of justice was especially significant on the example of ‘religion in the context of migration’ and of the ecumenic initiative ‘lebens.werte.schule’ (school worth living. The vision of the Kingdom of God and the necessity of participation become apparent. DEUTSCH: Im ersten Teil werden sechs Stationen am Lebensweg des Autors beschrieben, die seine Auseinandersetzung mit Gerechtigkeit geprägt haben. Der zweite Teil gibt Einblick in seine religionspädagogische Arbeit, in der die Frage nach Gerechtigkeit besonders bedeutsam war am Beispiel ‚Religion im Kontext Migration‘ und der ökumenischen Initiative ‚lebens.werte.schule‘. Die Vision vom Reich Gottes und die Notwendigkeit von Partizipation werden dabei deutlich.

  2. Die EG-Kabotageverordnung

    Basedow, Jürgen

    1990-01-01

    Die EG-Kabotageverordnung : e. Schritt zur Verwirklichung d. Dienstleistungsfreiheit im Straßengüterverkehr / Jürgen Basedow ; Ansgar Held. - In: Europäische Zeitschrift für Wirtschaftsrecht. 1. 1990. S. 305-308

  3. Die Bibliothek des Bezirksmuseums Josefstadt

    Maria Ettl

    2015-01-01

    Josefstadt in Wien werden die Herkunft der Bibliotheksbestände und die beengte Raumsituation beschrieben. Abschließend wird auf die Erfassung der Medien mittels der Bibliothekssoftware „Biblioweb“ eingegangen.

  4. Die verband tussen die sielkundige kontrak en organisasieverbondenheid

    K. J. Stanz

    1999-06-01

    Full Text Available The relationship between the psychological contract and organisational commitment. The aim of this study is to design a measuring instrument with acceptable metric characteristics for the strength of the psychological contract within the South African context, and to determine empirically the relation between the strength of the psychological contract and organisational commitment. The Dhammanungune Model served as foundation for the design of the Strength of the Psychological Contract Questionnaire which consists of two scales namely, a needs expectation scale and a needs fulfilment expectation scale. The items of each scale have been formulated in the manner that ensures that the respondent reacts consecutively to two instructions namely, (a the level of the expectation and (b the importance of the expectation. This questionnaire was administered together with the Organisational Commitment Questionnaire to two population groups within the military environment. The Pearson Product Moment Correlation was calculated between the strength of the psychological contract and organisational commitment and the significance of the correlations was evaluated. Opsomming Die doel van die studie is om 'n meetinstrument met aanvaarbare metriese eienskappe vir die sterkte van die sielkundige kontrak vir Suid-Afrikaanse omstandighede te ontwerp en om empirics die verband tussen die sterkte van die sielkundige kontrak en organisasieverbondenheid te bepaal. Die sterkte van die sielkundige kontrak vraelys is op grond van die Dhammanungune-model ontwerp en het uit twee skale naamlik, die behoefteverwagting- en vervullingsverwagtingskale bestaan. Items vir eike skaal is sodanig geformuleer dat die respondent agteropeenvolgens op twee instruksies naamlik (a die vlak van die verwagting en (b die belangrikheid van die verwagting moet reageer. Die vraelys is saam met die organisasieverbondenheidsvraelys op twee populasies uit 'n militere omgewing toegepas. Die Pearson

  5. Focused Molding Using Adhesive Pads in Mehta Casting for Early-Onset Scoliosis.

    Abraham, Roby; Sponseller, Paul D

    2014-11-01

    Prospective clinical series. To determine the effect of adhesive pads placed over the apex of scoliosis curves on curve correction 1) after the first cast and 2) after the final cast. Early-onset scoliosis is often effectively managed by serial casting. Properly localizing the apex of the molds with the cast in place is challenging. The authors explored the effectiveness of a novel technique: incorporation of adhesive pads placed over the major curve apex before Mehta casting. The 27 patients who received body casts (2000-2013) were divided into 2 groups: those without and with apical adhesive pads (5-6 layers of pads placed on the major curve's apex during casting): non-pad (NP) group (n = 12) and pad (P) group (n = 15), respectively. Groups were compared regarding the percentage of Cobb angle change from the first cast and curve correction to a Cobb angle of cast curve correction was 39% ± 18% and 56% ± 17% in the NP and P groups, respectively. Of the 26 patients out of a cast, 11 (42%) had a Cobb angle of casting were effective in increasing the amount of major curve correction from the first cast for idiopathic early-onset scoliosis and in decreasing curves to <25° at final follow-up. Copyright © 2014 Scoliosis Research Society. Published by Elsevier Inc. All rights reserved.

  6. ToxCast Dashboard

    The ToxCast Dashboard helps users examine high-throughput assay data to inform chemical safety decisions. To date, it has data on over 9,000 chemicals and information from more than 1,000 high-throughput assay endpoint components.

  7. Zirconium and cast zirconium

    Krone, K

    1977-04-01

    A survey is given on the occurence of zirconium, production of Zr sponge and semi-finished products, on physical and mechanical properties, production of Zr cast, composition of the commercial grades and reactor grades qualities, metal cutting, welding, corrosion behavior and use.

  8. "Souvenir" casting silicosis.

    Carel, R S; Salman, H; Bar-Ziv, J

    1994-10-01

    A case of silicosis in a 47-year-old worker who was employed for many years in a small souvenir casting shop is described. This work site demonstrates many unfavorable characteristics of small industries, such as lack of awareness of the need for safety measures, exposure control, protection of workers, and lack of compliance with environmental and medical-legal standards.

  9. Agricultural ecosystem modelling. The basis for assessing the impact of possible land-use and climate changes. Final report; Agrooekosystemmodellierung. Grundlage fuer die Abschaetzung von Auswirkungen moeglicher Landnutzungs- und Klimaaenderungen. Abschlussbericht

    Wenkel, K.O. [ed.; Mirschel, W. [ed.

    1995-12-31

    This report presents the results of the BMBF-sponsored project Fundamentals and models for assessing the effect of climate changes on soil, plant development and the crops of an economically significant range of farm products. Its aim was to study, by means of the results obtained for winter wheat, the dependence of plant growth on temperature, radiation and water as well as nutrient supply for other economically important crop types. Building on this, process-oriented, climate-sensitive agricultural ecosystem models for winter rye, winter barley, sugar-beet and winter intercrops were developed, verified and, in some sites, validated. First scenario calculations served to demonstrate the climate sensitivity of these models. (orig./KW) [Deutsch] Im vorliegenden Bericht werden die Ergebnisse des BMBF - Vorhabens `Grundlagen und Modelle zur Abschaetzung von Klimaaenderungen auf den Boden, die Pflanzenentwicklung sowie den verwertbaren Ernteertrag einer wirtschaftlich bedeutenden Marktfruchtfolge` vorgestellt. Ziel des Vorhabens war es, auf der Grundlage der Erkenntnisse zur Fruchtart Winterweizen die Abhaengigkeit des Pflanzenwachstums von Temperatur, Strahlung sowie Wasser- und Naehrstoffversorgung fuer weitere wirtschaftlich bedeutende landwirtschaftliche Fruchtarten zu untersuchen und auf diesen Ergebnissen aufbauend prozessorientierte klimasensitive Agrooekosystemmodelle fuer Winterroggen, Wintergerste, Zuckerrueben und Winterzwischenfruechte zu entwickeln, zu verifizieren und an einigen Standorten zu validieren. Mit Hilfe von ersten Szenariorechnungen war die Klimasensibilitaet dieser Modelle nachzuweisen. (orig./KW)

  10. Die postpolitische Stadt

    Erik Swyngedouw

    2013-12-01

    Full Text Available Die Polis ist tot, es lebe die kreative Stadt! Während die Stadt, zumindest in Teilen des städtischen Raums, blüht und gedeiht, scheint die Polis im idealisierten griechischen Sinn dem Untergang geweiht; in diesem Verständnis ist sie der Ort der öffentlichen politischen Auseinandersetzung und demokratischen Unterhandlung und somit eine Stätte (oft radikaler Abweichung und Unstimmigkeit, an der die politische Subjektivierung buchstäblich ihren Platz hat. Diese Figur einer entpolitisierten (oder postpolitischen und postdemokratischen Stadt im Spätkapitalismus bildet das Leitmotiv des vorliegenden Beitrags. Ich lehne mich dabei an Jacques Rancière, Slavoj Žižek, Chantal Mouffe, Mustafa Dikeç, Alain Badiou und andere Kritiker jenes zynischen Radikalismus an, der dafür gesorgt hat, dass eine kritische Theorie und eine radikale politische Praxis ohnmächtig und unfruchtbar vor jenen entpolitisierenden Gesten stehen, die in der polizeilichen Ordnung des zeitgenössischen neoliberalen Spätkapitalismus als Stadtentwicklungspolitik [urban policy] und städtische Politik [urban politics] gelten. Ziel meiner Intervention ist es, das Politische wieder in den Mittelpunkt der zeitgenössischen Debatten über das Urbane zu stellen. [...

  11. Wear resistance of cast iron

    S. Pietrowski

    2008-10-01

    Full Text Available In this paper investigations of abrasive and adhesive wear resistance of different cast iron grades have been presented. Examinations showed, that the most advantageous pair of materials is the cast iron – the hardened steel with low-tempered martensite. It was found, that martensitic nodular cast iron with carbides is the most resistant material.

  12. Die histologie en ultrastruktuur van die hepatopankreas van die bloukurper Oreochromis mossambicus

    M. M. Nel

    1990-07-01

    Full Text Available Die histologie en ultrastruktuur van die hepatopankreas van die bloukurper Oreochromis mossambicus word beskryf. ’n Dun bindweefselkapsel omring die lewer. Die hepatosietrangskikking vertoon as lobules, met die koorde van hepatosiete wat vanaf ’n sentrale vene uitradieer en met mekaar anastomaseer. Indiwiduele lewerlohules vertoon nie duidelike grense nie, maar enkele duidelike triades word wel in die lewer van O. mossambicus aangetref. Die hepatosiete bevat ’n enkele ronde kern met ’n duidelike nukleolus en die growwe endoplasmiese retikula kom in twee of meer rye om die kerne en teen die selgrense van die hepatosiete voor. Die ander sitoplasmiese organelle kom verspreid in die hepatosietsitoplasma voor. Die eksokriene pankreasselle is om die portale venes gesetel. Die kerne van hierdie selle is rond en is hasaal in die kubies- tot silindervormige selle gelee. ’n Goedontwikkelde growwe endoplasmiese retikulum — vesikulêr, tubulêr en sirkulêr in vorm — en sektretoriese granules wat apikaal in die sel gelee is, kom voor.

  13. Control of cast iron and casts manufacturing by Inmold method

    S. Pietrowski

    2009-07-01

    Full Text Available In this paper the usability of cast iron spheroidizing process in mould control by ATD method as well as by ultrasonic method were presented. Structure of instrumentation needed for control form performance of cast iron spheroidizing by Inmold method was illustrated. Author, pointed out that amount of magnesium master alloy should obtain 0,8 ÷ 1,0% of mass in form at all. Such quantity of preliminary alloy assure of obtain of nodular graphite in cast iron. In consequence of this, is reduce the cast iron liquidus temperature and decrease of recalescence temperature of graphite-eutectic crystallization in compare with initial cast iron. Control of casts can be carried out by ultrasonic method. In plain cast iron, ferritic-pearlitic microstructure is obtaining. Additives of 1,5% Cu ensure pearlitic structure.

  14. Climate change and the Lower Weser region: Direct and indirect consequences of a climate change for the ecological situation in the Weser, the forelands and in the diked marshes. Final report; Klimaaenderung und Unterweserregion (KLIMU) 'Fallstudie Weseraestuar'. Direkte und indirekte Auswirkungen eines Klimawandels auf die oekologischen Verhaeltnisse in Weser, Vorland und Binnendeichsmarschen. Teilprojekt Oekologischer Komplex. T. A: Binnenland. Abschlussbericht

    Kraft, D.; Schirmer, M.

    2001-03-01

    In the subproject 'Ecological Complex' within the combined project 'Climate Change and the Lower Weser Region' (KLIMU), formerly 'Case Study Weser Estuary', the ecological effects of a climate change for the Lower Weser, the tidal forelands and the marshes protected by dikes are assessed. For the description of the ecological situation of the research area the biotope types acc. to DRACHENFELS are assessed and processed using a GIS (ARC View/ARC Info), complemented by relief data, status of protection, agricultural utilization and soil parameters. When a defined future climate (climate scenario) with +55 cm sea-level, +30 cm tidal rise, increased precipitation (but with -6% in summer.) and +2.7 C mean annual temperature acts upon this landscape, the following consequences will arise (without morphological adaptation), which are described in the final report part A for the marshes and in part B for the Lower Weser and the forelands: the shallow water areas of the Lower Weser increase by 29%, tidal areas by 55% and the tidal reeds by 250%; the grassland outside the summerdikes looses it's agricultural value and decreases by 30%. CO{sub 2}- and temperature-increase will rise the biomass production of the reeds by up to 25%, the invasion of neophytes and neozoans will be accelerated. In general the conditions in the foreland will become more natural. In the marshes protected by dikes the raised temperature will promote the invasion of thermophilic species as well; raised temperature and CO{sub 2}-contents of the atmosphere will allow an increase in productivity by 25% and thus help the agriculture. The biotope types of the moist grassland will remain dominated by agriculture, areas within 2 km from the dikes will tend to become more moist, areas far from there will in parts suffer from considerable drought during summer. The reaction options of the coastal protection result in the consumption of highly valued nature-areas (e.g. for a

  15. Modernity of parts in casting machines and coefficients of total productive maintenance

    S. Borkowski

    2010-10-01

    Full Text Available The goal of this study is to investigate the impact of equipment efficiency in casting machines on the quality of die castings made of Al-Si alloys in consideration of their modernity. Analysis focused on two cold-chamber die-casting machines. The assessment of modernity ofthe equipment was made based on ABC analysis of technology and Parker’s scale. Then, the coefficients of total productive maintenance(TPM were employed for assessment of the efficiency of both machines. Using correlation coefficients r allowed authors to demonstrate the relationships between individual TPM coefficients and the number of non-conforming products. The finding of the study is pointing to the differences between the factors which determine the quality of castings resulting from the level of modernity of machines.

  16. Physical modeling and numerical simulation of V-die forging ingot with central void

    Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

    2014-01-01

    Numerical simulation and physical modeling performed on small-scale ingots made from pure lead, having a hole drilled through their centerline to mimic porosity, are utilized to characterize the deformation mechanics of a single open die forging compression stage and to identify the influence...... of the lower V-die angle on porosity closure and forging load requirements of large cast ingots. Results show that a lower V-die angle of 120 provides the best closure of centerline porosity without demanding the highest forging loads or developing unreasonably asymmetric shapes that may create difficulties...... in multi-stage open die forging procedures....

  17. Die teologiese arbeid van Antonius HJ Gunneweg

    En dis 'n klein treetjie van klagte na aanklag en na protes teen die gode, die heersers wat die mens vernietig deur hom oor sy ware lewe te bedrieg. Die ideologie eis dan ook dienooreenkomstig die bevryding en emansipasie van die mens van die gode en van God (1983: 118—119). Volgens die Jahwis is dit die slang wat, ...

  18. Casting Characteristics of High Cerium Content Aluminum Alloys

    Weiss, D; Rios, O R; Sims, Z C; McCall, S K; Ott, R T

    2017-09-05

    This paper compares the castability of the near eutectic aluminum-cerium alloy system to the aluminum-silicon and aluminum-copper systems. The alloys are compared based on die filling capability, feeding characteristics and tendency to hot tear in both sand cast and permanent mold applications. The castability ranking of the binary Al–Ce systems is as good as the aluminum-silicon system with some deterioration as additional alloying elements are added. In alloy systems that use cerium in combination with common aluminum alloying elements such as silicon, magnesium and/or copper, the casting characteristics are generally better than the aluminum-copper system. In general, production systems for melting, de-gassing and other processing of aluminum-silicon or aluminum-copper alloys can be used without modification for conventional casting of aluminum-cerium alloys.

  19. The casting of western sculpture during the XIXth century: sand casting versus lost wax casting

    Beentjes, T.P.C.

    2014-01-01

    This paper will discuss research into bronze casting techniques as practiced during the XIXth and early XXth century. Both natural sand casting (fonte au sable naturel) and lost wax casting (fonte à la cire perdue) were employed during this period and sometimes rivalled for commissions. Before the

  20. Influence of autochthonous micro-organisms on sorption and remobilization of technetium and selenium. Final report; Einfluss der autochthonen Mikroflora auf die Sorption und Remobilisierung des Technetiums und des Selens. Abschlussbericht

    Maue, G.; Stroetmann, I.; Dott, W. [Technische Univ. Berlin (Germany). Fachgebiet Umwelthygiene; Taute, T.; Winkler, A.; Pekdeger, A. [Freie Univ. Berlin (Germany). Fachrichtung Rohstoff- und Umweltgeologie

    1996-10-31

    Within this research project the influence of autochthonous mirco-organisms on immobilization and remobilization of Technetium and Selenium was investigated. Both redoxsensitive radionuclides are part of the waste of nuclear fuel (Tc app. 6%). Former investigations have shown, that immobilization behaviour of both elements could be influenced by micro-organisms. It has not been known, if the autochthonous (or in situ) organisms from greater depth do also have an influence on radionuclide mobility. The autochthonous populations of micro-organisms in deep sediments and their influence on the migration of Tc and Se were investigated in this study. For this reason recirculation column experiments were carried out. Absolutely sterile and anaerobic handling was necessary for the sampling and the further treatment of the sediments and waters used in the experiments. Therefor special methods for sampling, storage and handling had been developed. The results of recirculation column test with autochthonous micro-organisms were compared with sterile parallel tests and were verified with the results of an elaborated version of the hydrogeochemical equilibration code PHREEQE. It was shown that the autochthonous micro-organisms had only very little influence on the migration behaviour. The reason is the very low population (less than 10 E+6 CFU). Nevertheless it has to be taken into consideration, that conventional laboratory experiments for the estimation of the retention capacities of sediments for hazardous waste lead to an overestimation, if the sediments are contaminated with allochthonous micro-organisms (CFU=colony forming units). (orig.) [Deutsch] In dem Forschungsvorhaben wurde der Einfluss der autochthonen Mikroorgansimen auf die Mobilitaet von Technetium und Selen untersucht. Beide redoxsensitiven Radionuklide sind im Abfall von Kernbrennelementen enthalten (Tc ca. 6%). Aus vorangegangenen Forschungsarbeiten ist bekannt, dass die Mobilitaet der beiden Elemente durch

  1. Die benutting van vraelyste met die oog op meer effektiewe ...

    UPuser

    effektiewe stresbeheer as een van die temas te hanteer. Op grond van die navorsing deur onder andere Lawson (1985) en Taylor (1999) sou ek graag die proses van differensiasie2 ook by genoemde lys voeg as tema vir bespreking tydens huweliksvoorbereiding. 2 Differensiasie kan beskryf word as die losmaakproses ...

  2. die aard van wetgewende diskresies by die suid-afrikaanse ...

    Administrator

    In enige moderne demokrasie is daar een of ander vorm van skeiding van magte tussen die wetgewende, uitvoerende en regsprekende gesag. Hierdie skeiding van magte, die sogenaamde trias politica, kan sover teruggevoer word as 1215, met die ondertekening van die Magna Carta deur Koning John van Engeland.

  3. die doeltreffendheid van die afrikaanse woordelys en spelreels

    sluiting by die reel vir die verdubbeling van medeklinkers na 'n kort, be- klemtoonde klinker, woorde soos ballet, ballon, terras, terrein, dissipel en dissipline slegs met een konsonant na die eerste vokaal gespel moes word, omdat daardie voorafgaande vokaal onbeklemtoon is. Ook hierdie uit- sondering op die reel word ...

  4. Die aanspraak op Goddelike steun in 'n konfliksituasie volgens die ...

    laws, and ethical or political principles. A synchronic investigation of relevant Old ... die toneel gebring met die vraag: 'aan wie se kant is God' (vgl bv The road to. Damascus 1979:6)? Volgens .... betrekking tot die Ou Testament: Hoe moet ons vasstel wie se kant God nou regtig kies, of wie veg aan die kant van God en wie ...

  5. Stochastic simulation of grain growth during continuous casting

    Ramirez, A. [Department of Aerounatical Engineering, S.E.P.I., E.S.I.M.E., IPN, Instituto Politecnico Nacional (Unidad Profesional Ticoman), Av. Ticoman 600, Col. Ticoman, C.P.07340 (Mexico)]. E-mail: adalop123@mailbanamex.com; Carrillo, F. [Department of Processing Materials, CICATA-IPN Unidad Altamira Tamps (Mexico); Gonzalez, J.L. [Department of Metallurgy and Materials Engineering, E.S.I.Q.I.E.-IPN (Mexico); Lopez, S. [Department of Molecular Engineering of I.M.P., AP 14-805 (Mexico)

    2006-04-15

    The evolution of microstructure is a very important topic in material science engineering because the solidification conditions of steel billets during continuous casting process affect directly the properties of the final products. In this paper a mathematical model is described in order to simulate the dendritic growth using data of real casting operations; here a combination of deterministic and stochastic methods was used as a function of the solidification time of every node in order to create a reconstruction about the morphology of cast structures.

  6. Stochastic simulation of grain growth during continuous casting

    Ramirez, A.; Carrillo, F.; Gonzalez, J.L.; Lopez, S.

    2006-01-01

    The evolution of microstructure is a very important topic in material science engineering because the solidification conditions of steel billets during continuous casting process affect directly the properties of the final products. In this paper a mathematical model is described in order to simulate the dendritic growth using data of real casting operations; here a combination of deterministic and stochastic methods was used as a function of the solidification time of every node in order to create a reconstruction about the morphology of cast structures

  7. Inverse thermal analysis method to study solidification in cast iron

    Dioszegi, Atilla; Hattel, Jesper

    2004-01-01

    Solidification modelling of cast metals is widely used to predict final properties in cast components. Accurate models necessitate good knowledge of the solidification behaviour. The present study includes a re-examination of the Fourier thermal analysis method. This involves an inverse numerical...... solution of a 1-dimensional heat transfer problem connected to solidification of cast alloys. In the analysis, the relation between the thermal state and the fraction solid of the metal is evaluated by a numerical method. This method contains an iteration algorithm controlled by an under relaxation term...... inverse thermal analysis was tested on both experimental and simulated data....

  8. Cast iron - a predictable material

    Jorg C. Sturm

    2011-02-01

    Full Text Available High strength compacted graphite iron (CGI or alloyed cast iron components are substituting previously used non-ferrous castings in automotive power train applications. The mechanical engineering industry has recognized the value in substituting forged or welded structures with stiff and light-weight cast iron castings. New products such as wind turbines have opened new markets for an entire suite of highly reliable ductile iron cast components. During the last 20 years, casting process simulation has developed from predicting hot spots and solidification to an integral assessment tool for foundries for the entire manufacturing route of castings. The support of the feeding related layout of the casting is still one of the most important duties for casting process simulation. Depending on the alloy poured, different feeding behaviors and self-feeding capabilities need to be considered to provide a defect free casting. Therefore, it is not enough to base the prediction of shrinkage defects solely on hot spots derived from temperature fields. To be able to quantitatively predict these defects, solidification simulation had to be combined with density and mass transport calculations, in order to evaluate the impact of the solidification morphology on the feeding behavior as well as to consider alloy dependent feeding ranges. For cast iron foundries, the use of casting process simulation has become an important instrument to predict the robustness and reliability of their processes, especially since the influence of alloying elements, melting practice and metallurgy need to be considered to quantify the special shrinkage and solidification behavior of cast iron. This allows the prediction of local structures, phases and ultimately the local mechanical properties of cast irons, to asses casting quality in the foundry but also to make use of this quantitative information during design of the casting. Casting quality issues related to thermally driven

  9. Cast Ductile Iron 155mm M804 Bodies

    1990-07-12

    for the final delivery. The balance of the parts were returned to Wagner Castings for analysis, scrap, or de-militarization. The radiographic...as possible to avoid pre-cure. Mixing/ mulling time should be consistent with the system " worklife " or poor composite properties will result. Tensile...Burn-in on castings is caused by poor sand density, poor mixing, out of balance mix or improper drying of the wash. Long set times are an indication

  10. Die huwelik as identiteitsmerker in die Ou Testament

    p1243322

    Gen 2:18). Uit die woorde van Genesis 2:24 dat man en vrou een sal wees, lei die derde formulier af dat dit “getuig dat die huwelik 'n allesinsluitende gemeenskap is ..... die formule gebruik word: “Hier volg die vertelling oor X se nageslag.” (Gen ..... verwys daarna as “intertwining the principal value concepts of tradition”.

  11. Melting and casting of FeAl-based cast alloy

    Sikka, V.K. [Oak Ridge National Lab., TN (United States); Wilkening, D. [Columbia Falls Aluminum Co., Columbia Falls, MT (United States); Liebetrau, J.; Mackey, B. [AFFCO, L.L.C., Anaconda, MT (United States)

    1998-11-01

    The FeAl-based intermetallic alloys are of great interest because of their low density, low raw material cost, and excellent resistance to high-temperature oxidation, sulfidation, carburization, and molten salts. The applications based on these unique properties of FeAl require methods to melt and cast these alloys into complex-shaped castings and centrifugal cast tubes. This paper addresses the melting-related issues and the effect of chemistry on the microstructure and hardness of castings. It is concluded that the use of the Exo-Melt{trademark} process for melting and the proper selection of the aluminum melt stock can result in porosity-free castings. The FeAl alloys can be melted and cast from the virgin and revert stock. A large variation in carbon content of the alloys is possible before the precipitation of graphite flakes occurs. Titanium is a very potent addition to refine the grain size of castings. A range of complex sand castings and two different sizes of centrifugal cast tubes of the alloy have already been cast.

  12. CAST reaches milestone but keeps on searching

    CERN Courier (september 2011 issue)

    2011-01-01

    After eight years of searching for the emission of a dark matter candidate particle, the axion, from the Sun, the CERN Axion Solar Telescope (CAST) has fulfilled its original physics programme.   Members of the CAST collaboration in July, together with dipole-based helioscope. CAST, the world’s most sensitive axion helioscope, points a recycled prototype LHC dipole magnet at the Sun at dawn and dusk, looking for the conversion of axions to X-rays. It incorporates four state-of-the-art X-ray detectors: three Micromegas detectors and a pn-CCD imaging camera attached to a focusing X-ray telescope that was recovered from the German space programme (see CERN Courier April 2010).  Over the years, CAST has operated with the magnet bores - the location of the axion conversion - in different conditions: first in vacuum, covering axion masses up to 20 meV/c2, and then with a buffer gas (4He and later 3He) at various densities, finally reaching the goal of 1.17 eV/c2 on 22 ...

  13. Performance Steel Castings

    2012-09-30

    system components to be built. Figure la shows the machine design . PSC-2012 Page 94 Glue Application Sheet Transfer Feed Elevator Figure la...Department of Defense such as cleats, ejection chutes , control arms, muzzle brakes, mortar components, clevises, tow bar clamps, ammo conveyor elements...Foundry and the members of Steel Founders’ Society of America. Abstract Weapon system designers and builders need advanced steel casting technology

  14. Casting and Splinting

    2017-08-21

    mcludmg suggost1ons klr reducing lite burden, to the Department ar Defense. Executive Service Director> lte (07,IJ4-0188). Respondents should be...Orthoglass) Casting Material );;:- Fiberglass , .... • \\ \\ General Principles )- Measure out dry material at extremity being treated ~Plaster...shrinks slightly when wet; If too long can fold ends back ~Can be measured on contralateral extremity > Apply 2-3 layers of webril, avoid wrinkles

  15. Narratiwiteit en die Ou Testament

    INLEIDING. Die literêre benadering tot die Ou-Testamentiese narratiewe word algemeen as 'n alternatiewe paradigma in die Bybelwetenskappe aanvaar. Oor die filosofiese uit- gangspunte wat hierdie nuwe paradigma ten grondslag lê, bestaan daar egter nog weinig eenstemmigheid. Heelwat probleme van filosofiese en ...

  16. Eksistensialisme in die Franse letterkunde

    A. A. Teurlinckx

    1966-03-01

    Full Text Available Nooit sou die Franse jeug — en die van Europa en verder — in dié mate deur die eksistensialisme be'invloed gewees het nie, indien hierdie filosofie in wysgerige traktate sou begrawe gelê het. Die eksistensialiste het die koning van die filosofiese verhaal, Voltaire, met sukses op sy Candide- en Zadig-pad gevolg en hulle teorieë in letterkundige werke, ver- hale, romans en ook toneelstukke kwytgeraak, wat baie gelees is en waaruit ook ander literatore kragte en inspirasie geput het. Omrede daarvan is daar inderdaad baie eksistensialisme in die Franse letterkunde, maar ’n eintlike eksistensialistiese letterkunde was daar nie, en ’n Eksistensialistiese Letterkun­ dige skool het nooit bestaan nie. Ook sit hierdie eksistensialiste nie langs dieselfde vuur nie. Die Christelike eksistensialis Gabriel Marcel het op 21 April van hierdie jaar uitgevaar teen die „Sartriane” na aanleiding van die opvoering van Les Paravents, Die W indskerms van Jean Genêt in ’n Paryse staatsondersteunde teater. „Mens mag seker wees”, skryf Marcel in Les Nouvelles Littéraires, „dat die hele sartriaanse parogie sal skreeu: groot meesterwerk”. Voortgaande op sy distansiëring kan die literêre eksistensialiste in drie groepe ingedeel word: 1. Die Sartriane; 2. Die Christelike Eksistensialiste; 3. Die Onafhanklikes.

  17. Casting defects and fatigue behaviour of ductile cast iron for wind turbine components: A comprehensive study

    Haerkegaard, G. [Norwegian University of Science and Technology, Dept. of Engineering Design and Materials, Trondheim (Norway); Shirani, M.

    2011-12-15

    Two types of EN-GJS-400-18-LT ductile cast iron were investigated in this research, clean baseline material in the shape of castings with different thicknesses and also defective material from a rejected wind turbine hub. P-S-N curves for baseline EN-GJS-400-18-LT specimens with different dimensions and from castings with different thicknesses at different load ratios were established. Geometrical size effect, technological size effects and mean stress effect on fatigue strength of baseline EN-GJS-400-18-LT were evaluated. Fatigue strength of baseline EN-GJS-400-18-LT was compared with that of defective material from the rejected hub. The effect of defects type, shape, size and position on fatigue strength of this material was evaluated. The hypothesis that the endurance observed in an S-N test can be predicted based on the analysis of crack growth from casting defects through defect-free 'base' material was tested for the analyzed defective material. 3D X-ray computed tomography was use to detect defects in defective specimens and find the defect size distribution. The obtained defect size distribution for the defective material was used in random defect analysis to establish the scatter of fatigue life for defective specimens. Finally both safe-life design and damage tolerant design of wind turbine castings were analyzed and compared. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  18. Rheo-Cast Microstructure and Mechanical Properties of AM60 Alloy Produced by Self-Inoculation Rheo-Diecasting Process

    Bo Xing

    2016-03-01

    Full Text Available Rheo-forming is becoming the choice for production of high quality parts with diminished defects and fine integrity. In this paper, the novel self-inoculation rheo-diecasting (SIRD process, in which semisolid slurry is produced by mixing two precursory solid and liquid alloys and subsequently pouring them through a multi-stream fluid director, has been proposed. Microstructural characteristics of AM60 alloy slurry and the microstructure and mechanical properties of rheo-diecasting AM60 samples were investigated. Quenching experiments reveal that the slurry microstructure of AM60 was well refined to irregular α-Mg particles with the average size of approximately 20–40 μm after pouring with the self-inoculation process, and these particles were evolved to globular and coarse morphology while continuously keeping in semisolid state. After rheo-diecasting, the microstructure of the sample was dominated by fine primary α-Mg globules accompanied with tiny secondary α-Mg particles while the sample from conventional liquid die casting was characterized by developed dendrite and porosity. Microscopic analysis indicates that there are three stages of remaining liquid solidification in die cavity in SIRD: α-Mg nucleation and growth on primary α-Mg surface, α-Mg nucleated independently in liquid, and, finally, formation of skeleton devoiced eutectic. Due to diminished porosity and hot tearing, tensile strength and elongation of SIRD samples were increased by 12.9% and 35.3%, respectively, compared to a conventional liquid die casting sample.

  19. Optimization of Squeeze Casting Parameters for 2017 A Wrought Al Alloy Using Taguchi Method

    Najib Souissi

    2014-04-01

    Full Text Available This study applies the Taguchi method to investigate the relationship between the ultimate tensile strength, hardness and process variables in a squeeze casting 2017 A wrought aluminium alloy. The effects of various casting parameters including squeeze pressure, melt temperature and die temperature were studied. Therefore, the objectives of the Taguchi method for the squeeze casting process are to establish the optimal combination of process parameters and to reduce the variation in quality between only a few experiments. The experimental results show that the squeeze pressure significantly affects the microstructure and the mechanical properties of 2017 A Al alloy.

  20. Die afrikaner en sy pers*

    G. D. Scholtz

    1963-03-01

    Full Text Available Die versoek w at van u inrigting tot my gekom het om buitengewone professor in die Persw etenskap te word, was vir my deels vererend, m aar deels het dit my in 'n moeilike posisie gestel. Dit was vir my vererend, om dat dit gekom het van 'n universiteit m et wie se Christelik- Nasionale koers ek my ten voile kan vereenselwig. Dit was dan ook vir my vererend, om dat ek daardeur in staat gestel kan w ord om die volk w aartoe ek behoort, op 'n vir my nuwe terrein te dien. As sodanig is dit vir my im m ers m oontlik om ook ’n beskeie bydrae te lewer tot die geestelike vorm ing van die jeug van ons volk. Dit het my m oeilik geval om, w aar ek reeds die m iddeljarige leeftyd bereik het, nou vir die eerste maal as dosent op te tree, aangesien ek daarvan in die verlede nie die m inste kennis en ervaring opgedoen het nie. As joernalis rig ek my im m ers tot die breë publiek deur middel van die pen. As dosent m oet ek my deur middel van die mond tot die studente rig. Dit lê voor die hand dat die eise w at so aan my gestel word, totaal anders is as dié waar- aan ek oor 'n tydperk van m eer as 'n kw arteeu as joer­ nalis gewoond geraak het.

  1. Die vestiging van die Kerk in Natal, die Vrystaat en Transvaal na ...

    as eerste predikant van die Voortrekkers laat orden en bevestig. Daama het verskeie kerksake van tyd tot tyd aandag geniet. Met betrekking tot die bevestiging van huwelike stel Retief 'n meer ordelike reëling daar, naamlik dat die gebooie van voomemende egpa- re van nou af drie maal in die kerk afgekondig moes wrord ...

  2. Effects of selected casting methods on mechanical behaviour of Al-Mg-Si alloy

    Henry Kayode TALABI

    2014-11-01

    Full Text Available This study investigated the effects of selected casting methods on mechanical behaviour of Al-Mg-Si alloy. The casting methods used was spin, sand and die casting, these were done with a view to determine which of the casting methods will produce the best properties. The pure aluminium scrap, magnesium and silicon were subjected to chemical analysis using spectrometric analyzer, thereafter the charge calculation to determine the amount needed to be charged into the furnace was properly worked out and charged into the crucible furnace from which as-cast aluminium was obtained. The mechanical properties of the casting produced were assessed by hardness and impact toughness test. The optical microscopy and experimental density and porosity were also investigated. From the results it was observed that magnesium and silicon were well dispersed in aluminium matrix of the spin casting. It was observed from visual examination after machining that there were minimal defects. It was also observed that out of the three casting methods, spin casting possesses the best mechanical properties (hardness and impact toughness.

  3. Hot forging of roll-cast high aluminum content magnesium alloys

    Kishi, Tomohiro; Watari, Hisaki; Suzuki, Mayumi; Haga, Toshio

    2017-10-01

    This paper reports on hot forging of high aluminum content magnesium alloy sheets manufactured using horizontal twin-roll casting. AZ111 and AZ131 were applied for twin-roll casting, and a hot-forging test was performed to manufacture high-strength magnesium alloy components economically. For twin-roll casting, the casting conditions of a thick sheet for hot forging were investigated. It was found that twin-roll casting of a 10mm-thick magnesium alloy sheet was possible at a roll speed of 2.5m/min. The grain size of the cast strip was 50 to 70µm. In the hot-forging test, blank material was obtained from as-cast strip. A servo press machine with a servo die cushion was used to investigate appropriate forging conditions (e.g., temperature, forging load, and back pressure) for twin-roll casts (TRCs) AZ111 and AZ131. It was determined that high aluminum content magnesium alloy sheets manufactured using twin-roll casting could be forged with a forging load of 150t and a back pressure of 3t at 420 to 430°C. Applying back pressure during hot forging effectively forged a pin-shaped product.

  4. Numerical simulation of complex multi-phase fluid of casting process and its applications

    CHEN Li-liang

    2006-05-01

    Full Text Available The fluid of casting process is a typical kind of multi-phase flow. Actually, many casting phenomena have close relationship with the multi-phase flow, such as molten metal filling process, air entrapment, slag movement, venting process of die casting, gas escaping of lost foam casting and so on. Obviously, in order to analyze these phenomena accurately, numerical simulation of the multi-phase fluid is necessary. Unfortunately, so far, most of the commercial casting simulation systems do not have the ability of multi-phase flow modeling due to the difficulty in the multi-phase flow calculation. In the paper, Finite Different Method (FDM technique was adopt to solve the multi-phase fluid model. And a simple object of the muiti-phase fluid was analyzed to obtain the fluid rates of the liquid phase and the entrapped air phase.

  5. Continuation of Crosscutting Technology Development at Cast

    Yoon, Roe-Hoan

    2012-03-31

    This Final Technical Report describes progress made on the sub-projects awarded in the Cooperative Agreement DE-FC26-05NT42457: Continuation of Crosscutting Technology Development at Center for Advanced Separation Technologies (CAST). The final reports for each sub-project are attached in the appendix. Much of the research to be conducted with Cooperative Agreement funds will be longer-term, high-risk, basic research and will be carried out in five broad areas: a) Solid-solid separation b) Solid-liquid separation c) Chemical/Biological Extraction d) Modeling and Control, and e) Environmental Control.

  6. Die skool en die onderwyser as faktore in die geestesgesondheid van die kind*

    B. C. Schutte

    1961-03-01

    Full Text Available Ons hou geestesgesondheidsweke, stig beroepsentrums, samel geld in om mense wat geestelik siek is te genees, klae oor die tekort aan psigiaters, kliniese sielkundiges, bedryfsielkundiges, voorligters, skoolpsigoloë,ens. ’n Karige kwarteeu gelede het ons aan al hierdie dinge slegs akademiese aandag gewy. In hierdie kursus wordverskeie tipes kinders bespreek en geleer hoe om hulle probleme te benader.

  7. When Somebody Dies

    ... bottle became useless. The container is gone, but what's inside — the water — remains. The part of a person that's left after the body dies is often called the "soul" or "spirit." Some people believe the soul is the part ...

  8. Die Kunst des Scheiterns

    Juul, Jesper

    2014-01-01

    Menschen haben von Kindesbeinen an das Verlangen, Erfolge zu erzielen und Kompetenz zu erreichen. Computerspieler entscheiden sich jedoch fortlaufend für eine Aktivität, die oft und wiederholt zum Verlieren führen muss und ein taubes Gefühl der Unfähigkeit erzeugt. Im Kino, im Theatersaal und bei...

  9. Medium-term forecast of the Germany-wide electricity supply to final consumers for the calendar years 2016 to 2020. Study on behalf of the German transmission system operators; Mittelfristprognose zur Deutschland-weiten Stromabgabe an Letztverbraucher fuer die Kalenderjahre 2016 bis 2020. Studie im Auftrag der Deutschen Uebertragungsnetzbetreiber

    Elsland, Rainer; Bossmann, Tobias; Klingler, Anna-Lena; Friedrichsen, Nele; Klobasa, Marian

    2015-10-15

    almost decisive for the amount of the EEG apportionment, depends on the development of the privileged final consumption and the associated payment flows. The amendment of the EEG in 2014 also resulted in a reform of the special compensation scheme (BesAR). This implies a much more complex calculation methodology for the calculation of privileged final consumption quantities. For 2016, a privileged final consumption of about 104 TWh is expected, which is slightly below the level of the previous years. This declining trend will continue in the coming years due to efficiency improvements in the industry, reaching a level of 101 TWh in 2020. The related allocation payments amount to 467 million Euros in 2016. Taking into account the prognosticated amounts for net electricity demand, self-procured self-supply and privileged final consumption, a non-privileged final consumption amounting to around 356 TWh results for 2016. It can be expected that the future decline in demand for net electricity will have a direct impact on the medium-term development of non-privileged final consumption, as the increase in self-sufficiency is compensated by a reduction in privileged final consumption. Accordingly, non-privileged final consumption is reduced to 351 TWh by the year 2020. [German] Die deutschen Uebertragungsnetzbetreiber sind verpflichtet, kalenderjaehrlich Prognosen zur Entwicklung der bundesweiten EEG-Umlage zu erstellen und zu veroeffentlichen. Ein wesentlicher Bestandteil dieser Untersuchung stellt eine Prognose der Stromabgabe an Letztverbraucher dar. Dabei ist neben dem Stromverbrauch der Eigenversorger auch der Letztverbrauch differenziert nach Privilegierungskategorien zu untersuchen, fuer den die EEG-Umlage in verringerter Hoehe gezahlt werden muss. Der Letztverbrauch betrug im Jahr 2014 in etwa 463 TWh und sinkt kontinuierlich bis zum Jahr 2020 auf etwa 446 TWh ab. Im Jahr 2016 betraegt der Letztverbrauch rund 460 TWh. Der Rueckgang des Letztverbrauchs faellt

  10. Effects of climate dependent modifications of the local conditions on the fauna of selected coastal ecological systems of the middle Baltic Sea. Final report; Auswirkungen von klimaabhaengigen Aenderungen der Standortbedingungen auf die Fauna ausgewaehlter Kuestenoekosysteme der mittleren Ostsee. Schlussbericht

    Mueller-Motzfeld, G.; Schultz, R.; Loch, R.; Wohlrab, B.; Cartellieri, M.; Rulik, B.

    2000-07-01

    In the project 'Effects of climate dependent modifications of the local conditions on the fauna of selected coastal ecological systems of the middle Baltic Sea' carabid beetles and spiders were examined with pitfall traps in 1997 and 1998 on two different meadows at the southern Baltic Sea (NE Germany). The investigation areas were the 'Sundisch Meadow', located in the National Park 'Vorpommersche Bodenlandschaft', and the 'Karrendorf Meadows' near Greifswald. The epigeic fauna were examined with five parallel pitfall traps on transects in 20, 40, 60, 100 and 150 cm above NH. In both years investigations of the reference area seawards of the former dike took place on the Karrendorf Meadows, since this area is annually examined in the context of the monitoring 'Revitalisation of the Karrendorf Meadows'. On both investigation areas the regional climatic conditions and the hydrographic situation were registered. Additionally, several soil-parameters were measured at all trap locations: Carbon content, N-content, N{sub C}-relation, pH value, salinity, grain size, water content, damp and dry bulk density. In the context of the long-term monitoring programme 'Revitalisation of the Karrendorf Meadows' the development of the ground beetles and spiders was studied after the vitalisation of this former coastal transgression mire. (orig.) [German] Im Rahmen des Teilprojektes 'Auswirkungen von klimaabhaengigen Aenderungen der Standortbedingungen auf die Fauna ausgewaehlter Kuestenoekosysteme der mittleren Ostsee' fanden 1997 und 1998 Bodenfallenuntersuchungen auf der Sundischen Wiese im Nationalpark Vorpommersche Boddenlandschaft und auf den Karrendorfer Wiesen bei Greifswald statt. Untersucht wurde die Laufkaefer und Spinnenfauna mit Hilfe eines Transsektes von jeweils fuenf parallelen Bodenfallen in den Hoehenstufen 20, 40, 60, 100 und 150 cm ueber HN. Zusaetzlich wurde 1997 auf der Sundischen Wiese eine

  11. Modelle in die onderrig van fisika

    J. J. A. Smit

    1998-07-01

    Full Text Available Die rol van modelle in die onderrig van fisika is sedert die vroeë tagtigerjare erken. In die onderrig word die absent op die kwantitaiewe aspekte van die vak geplaas, terwyl die kwatitatiewe aspekte min aandag kry.

  12. DIE SAGD - SY ONTSTAAN EN ONTWIKKELING

    31 Okt 1977 ... stelling van 'n higiene afdeling het in 'n belang- rike behoefte voorsien. Die pligte van die SAGO het dus op hierdie stadium die ondersoek van soldate, die sanita- sie van kampe, die verpleging van pasiente in militere hospitale en die opleiding van lede be- hels. 'n Hoogtepunt was die opening van die.

  13. Die transvaalse ontwerp-ordonnansie oor die onderwys

    J. C. Coetzee

    1952-03-01

    Full Text Available In ’n Buitengewone Provinsiale Koerant van die Provinsie Transvaal is onder datum 25 Junie 1952 gepubliseer ’n „Ontwerp-Ordonnansie tot samevatting en wysiging van die Wette betreffende die Sentrale Beheer van die Onderwys, die Plaaslike Beheer van Skole, Godsdiensonderrig in Openbare Skole, Taal en die Onderwys, Onderwyspersoneel, Verpligte Onderwys, Toelating van Leerlinge tot Skole, Klasse of Inrigtings, Openbare Onderwys, Private Skole, Onderwys vir Kleurlinge en Asiate en Onderwys vir Naturelle, en om vir sake in verband daarmee voorsiening te maak” .

  14. DIE HEDENDAAGSE SIENING VAN DIE NORMERING VAN DUITS ...

    v a k t a a l k w a l i £ i k a s i e s ) neem d i e I n s t i t u t t a l l e take waar ter u i t b r e i d i n g van kennis van die Duitse taal in die buiteland. Sedert 1964 publiseer die. Institut die tydskrif Deutsch als Fremdsprache met die bylae Sprachpraxis, asook 'n handboek met die titel Deutsch - eln Lehrbuch Eur Auslander (Duits.

  15. Navigating "Assisted Dying".

    Schipper, Harvey

    2016-02-01

    Carter is a bellwether decision, an adjudication on a narrow point of law whose implications are vast across society, and whose impact may not be realized for years. Coupled with Quebec's Act Respecting End-of-life Care it has sharply changed the legal landscape with respect to actively ending a person's life. "Medically assisted dying" will be permitted under circumstances, and through processes, which have yet to be operationally defined. This decision carries with it moral assumptions, which mean that it will be difficult to reach a unifying consensus. For some, the decision and Act reflect a modern acknowledgement of individual autonomy. For others, allowing such acts is morally unspeakable. Having opened the Pandora's Box, the question becomes one of navigating a tolerable societal path. I believe it is possible to achieve a workable solution based on the core principle that "medically assisted dying" should be a very rarely employed last option, subject to transparent ongoing review, specifically as to why it was deemed necessary. My analysis is based on 1. The societal conditions in which have fostered demand for "assisted dying", 2. Actions in other jurisdictions, 3. Carter and Quebec Bill 52, 4. Political considerations, 5. Current medical practice. Leading to a series of recommendations regarding. 1. Legislation and regulation, 2. The role of professional regulatory agencies, 3. Medical professions education and practice, 4. Public education, 5. Health care delivery and palliative care. Given the burden of public opinion, and the legal steps already taken, a process for assisted-dying is required. However, those legal and regulatory steps should only be considered a necessary and defensive first step in a two stage process. The larger goal, the second step, is to drive the improvement of care, and thus minimize assisted-dying.

  16. Improved Casting Furnace Conceptual Design

    Fielding, Randall Sidney [Idaho National Lab. (INL), Idaho Falls, ID (United States); Tolman, David Donald [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2017-02-01

    In an attempt to ensure more consistent casting results and remove some schedule variance associated with casting, an improved casting furnace concept has been developed. The improved furnace uses the existing arc melter hardware and glovebox utilities. The furnace concept was designed around physical and operational requirements such as; a charge sized of less than 30 grams, high heating rates and minimal additional footprint. The conceptual model is shown in the report as well as a summary of how the requirements were met.

  17. Cast dielectric composite linear accelerator

    Sanders, David M [Livermore, CA; Sampayan, Stephen [Manteca, CA; Slenes, Kirk [Albuquerque, NM; Stoller, H M [Albuquerque, NM

    2009-11-10

    A linear accelerator having cast dielectric composite layers integrally formed with conductor electrodes in a solventless fabrication process, with the cast dielectric composite preferably having a nanoparticle filler in an organic polymer such as a thermosetting resin. By incorporating this cast dielectric composite the dielectric constant of critical insulating layers of the transmission lines of the accelerator are increased while simultaneously maintaining high dielectric strengths for the accelerator.

  18. Design options for process control systems in an attempt to integrate experiential knowledge and cooperation in process and power systems based on continuous processes (definition phase). Final report; Gestaltungsoptionen fuer die Prozessleittechnik zur Foerderung erfahrungsgeleiteter Arbeit und Kooperation in verfahrens- und energietechnischen Anlagen mit kontinuierlichen Prozessen (Definitionsphase). Schlussbericht

    Lappus, G. [ed.; Gomol, S.; Popov, K.; Winzer, P.; Moldaschl, P.; Rose, H.; Hering, S.

    1997-05-01

    An innovative interaction concept for process control was developed at BTU Cottbus university. The concept integrates such aspects as process control, environmental protection, maintenance and quality assurance. It is to be managed by a user group with the emphasis on empirical work and cooperation, industrial sociology and psychology, and acquilsition and multimedia use of experiential knowledge. For this purpose, empirical data were compiled and evaluated. Two workshops and a final presentation served to discuss the data with potential users and to get new ideas. Each project partner drew up a concept paper with their own ideas and proposed solutions. After the workshops and the final presentation, these papers were revised again. A demonstrator was developed in order to be able to present the new concept and ideas to potiential partners in industry, and a final report comprising a summary description and outlook was published. (orig.) [Deutsch] An der BTU Cottbus wurde ein innovatives Interaktionskonzept fuer Prozessfuehrung entwickelt, das verschiedene Arbeitsbereiche bzw. Systeme integrativ zusammenfuehrt, insbesondere Prozessleittechnik, Umweltschutz, Instandhaltung und Qualitaetssicherung und das andererseits von einer Nutzergruppe beherrscht werden soll, wobei die Aspekte erfahrungsgeleitete Arbeit und Kooperation, industriesoziologische und arbeitspsychologische Effekte und Aufbau und multimediale Nutzung von Erfahrungswissen im Mittelpunkt standen. Dazu wurden empirische Erhebungen vorbereitet, durchgefuehrt und ausgewertet. Zwei Workshops und eine Abschlusspraesentation dienten dazu, mit potentiellen Nutzern zu diskutieren und neue Anregungen zu bekommen. Jeder Projektpartner erstellt ein Konzeptpapier mit seinen Vorstellungen und ersten Loesungsansaetzen. Diese wurden nach den Workshops und der Abschlusspraesentation nochmals ueberarbeitet. Ein Demonstrator wurde entwickelt, um eventuellen Industriepartnern das neue Konzept und die Ideen des Vorhabens

  19. Advanced Casting Technology

    1982-08-01

    Anodic Films for the Protection of Magnesium Alloys". G.R. Kotler, D.L. Hawke and E.N. Agua . Proc. International Magnesium Association, Montreal, May...HCF testing, impellers were bench tested to assess the in situ fatigue capabilities of 250-C28 impeller airfoils. In this testing, the airfoils...64 at 204oC (400oF), 13- T to a> o >-, o r- i—l CD -*—• Cast Wrought TE-2222 Ficure 11. In situ HCF results for Ti-64 Model 250

  20. Effects of preparation relief and flow channels on seating full coverage castings during cementation.

    Webb, E L; Murray, H V; Holland, G A; Taylor, D F

    1983-06-01

    Machined steel dies were used to study the effects of three die modifications on seating full coverage castings during cementation. The die modifications consisted of occlusal channels, occlusal surface relief, and axial channels. Fourteen specimens having one or more forms of die modification were compared with two control specimens having no die modifications. Statistical analysis of the data revealed that the addition of four axial channels to the simulated preparation on the steel die produced a significant reduction in the mean marginal discrepancy during cementation. Occlusal modifications alone failed to produce significant reductions in marginal discrepancies when compared with the control specimens. Occlusal modifications in conjunction with axial channels failed to produce further significant reductions in marginal discrepancies when compared with those reductions observed in specimens having only axial channels.

  1. INFLUENCE OF DIE ANGLES ON THE MICROHARDNESS OF ALUMINUM ALLOY PROCESSED BY EQUAL CHANNEL ANGULAR PRESSING

    Ali A Aljubouri

    2010-11-01

    Full Text Available   The die geometry has a massive effect on the plastic deformation behavior during pressing of material processed by equal channel angular pressing (ECAP method; subsequently the properties of the processed material are strongly dependent on it. Two categories of designed and manufactured dies are used for equal channel angular pressing, a 1200 sharp angle and a 900 round –cornered (200 dies, that produce strain per pass through both dies of ~0.7 and ~1.05   respectively. The microhardness developed in Al-Si alloy during ECAP using route BC. The microhardness increased by a factor of >1.5, after only 1 pressing. Subsequently, the hardness increases slightly up to 8 pressings through the 1200 sharp angle die, while it is increased by a factor of ~2.6 after 5 passes by using the 900 round cornered die, comparing with that for the cast workpiece.

  2. Die historiese betroubaarheid van die aartsvadervertellinge. 'n Beknopte bespreking van die huidige debat na aanleiding van die jongste publikasie

    W. Vosloo

    1982-08-01

    Full Text Available Die afgelope twintig jaar was daar �n toenemende belangstelling in die aartsvadervertellinge in Genesis. Benewens die talle tydskrifartikels het skrywers soos die volgende ook boeke oor die onderwerp die lig laat sien: A. Parrot (1962, W. M. Clark (1964, R. Kilian (1966, R. E. Clements (1967, N. Lohfink (1967, H. Weidemann (1968, R. Martin-Achard (1969, T. L. Thompson (1974, J. van Seters (1975, J. P. Fokkelman (1975, C. Westermann (1976, R. Rendtorff (1977, J. Bright (1977, W. McKane (1979 en A. R. Millard en D. J. Wiseman (1980.

  3. 'n Kwalitatiewe ondersoek na die invloed van aspekte van die ...

    S Blignaut

    ISSN 0378-5254 Journal of Family Ecology and Consumer Sciences, Vol 26: No1, 1998. 15 ...... van byvoorbeeld die televisie en gedrukte media 'n invloed op die .... fashion promotion and advertising. New York. ... Consumer behaviour to-.

  4. Awareness programs and change in taste-based caste prejudice.

    Ritwik Banerjee

    Full Text Available Becker's theory of taste-based discrimination predicts that relative employment of the discriminated social group will improve if there is a decrease in the level of prejudice for the marginally discriminating employer. In this paper we experimentally test this prediction offered by Garry Becker in his seminal work on taste based discrimination, in the context of caste in India, with management students (potential employers in the near future as subjects. First, we measure caste prejudice and show that awareness through a TV social program reduces implicit prejudice against the lower caste and the reduction is sustained over time. Second, we find that the treatment reduces the prejudice levels of those in the left tail of the prejudice distribution--the group which can potentially affect real outcomes as predicted by the theory. And finally, a larger share of the treatment group subjects exhibit favorable opinion about reservation in jobs for the lower caste.

  5. Awareness programs and change in taste-based caste prejudice.

    Banerjee, Ritwik; Datta Gupta, Nabanita

    2015-01-01

    Becker's theory of taste-based discrimination predicts that relative employment of the discriminated social group will improve if there is a decrease in the level of prejudice for the marginally discriminating employer. In this paper we experimentally test this prediction offered by Garry Becker in his seminal work on taste based discrimination, in the context of caste in India, with management students (potential employers in the near future) as subjects. First, we measure caste prejudice and show that awareness through a TV social program reduces implicit prejudice against the lower caste and the reduction is sustained over time. Second, we find that the treatment reduces the prejudice levels of those in the left tail of the prejudice distribution--the group which can potentially affect real outcomes as predicted by the theory. And finally, a larger share of the treatment group subjects exhibit favorable opinion about reservation in jobs for the lower caste.

  6. N HERSIENING VAN DIE AFRIKAANSE VERTALING VAN DIE ...

    Test

    vergewe. Dit sou in orde gewees het as daar gestaan het, ReMomë- j^onta^is hepta?ds. wat die grieks is vir sewentig maal sewe. Die uitdrukking. heMom&ontabis heptd sien hoogswaarskynlik op Gen. 4 : 24 (LXX) waar. Lameg meedeel dat hy sewe-en-sewentig-maal gewreek sal word. Daar sit die Afr. Vert, die uitdrukking ...

  7. Die dilemma van die musiekwetenskaplike in die onderrigsituasie

    Bertha Spies

    1995-03-01

    Full Text Available The dilemma of the musicologist who is also a teacher. In this article a main educational objective, namely the interpretation of reality, forms the basis for discussing the dilemma of the musicologist who is also a teacher. Firstly, various facets of musical reality are discussed under the following headings: the meaning of reality for the musicologist, artistic representation of reality and an idealized musical reality. Secondly, the manner in which musical reality is interpreted is discussed. Thirdly, results of a fragmented musical reality are mentioned and finally, proposals aimed at solving the problem of the musicologist-teacher are put forward, arguing for a more objective view of reality as a whole, stressing the double responsibility of the musicologist-teacher to interpreting difficult texts and the necessity to re-evaluate traditional theories in the light of their didactic effectiveness.

  8. Film Presentation: Die Urknallmaschine

    Carolyn Lee

    2010-01-01

    Die Urknallmaschine, an Austrian film by Gerd Baldauf, narrated by Norbert Frischauf (Alpha Österreich - ORF, 2009).  In CERN’s gigantic complex particles are accelerated to almost the speed of light, brought to collision and made to divide into even smaller particles. Public opinion of CERN’s research is also divided. Sceptics fear that black holes may be created. Might the goal to study the origin of the world lead to its destruction? The Austrian researcher Norbert Frischauf worked at CERN for many years. With his guidance it is possible to explore the world’s largest research centre, get a glimpse of the fascinating work the scientists do there and take a crash course in particle physics. Die Urknallmaschine will be presented on Friday, 25 June from 13:00 to 14:00 in the Main Auditorium. Language: German

  9. Dying for security

    Buchan, Bruce

    2011-01-01

    Full Text Available If political statements and media coverage are any guide, it seems Australians today are dying for security. At no other moment in our history has the spectre of war and terrorism so haunted popular, political and scholarly perceptions of Australia’s colonial past and of its geopolitical future. And yet, debates over colonial war or genocide and contemporary terrorism have been conducted in more or less complete isolation. In this article I argue that our contemporary obsession with ‘security’ is premised on the perennial threat of ‘insecurity’. This is the problem of in/security, and it has played a central role in the development of Western political thought. More importantly, its formulation in Western political thought provided a powerful justification for the violence of the early decades of Australia’s colonisation during which Indigenous Australians could also be said to have been dying for security.

  10. Dying for Security

    Bruce Buchan

    2011-03-01

    Full Text Available If political statements and media coverage are any guide, it seems Australians today are dying for security. At no other moment in our history has the spectre of war and terrorism so haunted popular, political and scholarly perceptions of Australia’s colonial past and of its geopolitical future. And yet, debates over colonial war or genocide and contemporary terrorism have been conducted in more or less complete isolation. In this article I argue that our contemporary obsession with ‘security’ is premised on the perennial threat of ‘insecurity’. This is the problem of in/security, and it has played a central role in the development of Western political thought. More importantly, its formulation in Western political thought provided a powerful justification for the violence of the early decades of Australia’s colonisation during which Indigenous Australians could also be said to have been dying for security.

  11. N HERSIENING VAN DIE AFRIKAANSE VERTALING VAN DIE ...

    Test

    aangetoon het, 'n huis in Kapernaum gehad en hierdie geskiedenis speel in Kapernaum of daar digby af. Jesus en sy dissipele het namelik, volgens 6:35 geland by Gennesaret, net suid van Kapernaum Die gevolgtrekking word ondersteun deur Joh. 6:17 waarvolgens die dissi pele na die spysiging op Kapernaum gevaar ...

  12. 'n Verkenning van die soorte vennootskappe in die Amerikaanse reg ...

    In die Amerikaanse literatuur word talle verwysings gevind na die vennootskap in mynbou ("mining partnership"), familievennootskap ("family partnership", vennootskap in vaste eiendom ("partnership in real estate") en vennootskap vir boerdery ("farming partnership"). Hierdie onderskeiding is primer gebaseer op die tipe ...

  13. Geslagsverskille in die ouditiewe ontlokte potensiaal van die brein

    Anita D Stuart

    2006-10-01

    Full Text Available Gender differences in the auditory evoked potential of the brain. Based on literature indications of an association between temperament characteristics and the evoked potential of the brain, and indications of gender differences in certain temperament traits, the purpose of this study was to ascertain whether evoked responses also differentiated between the genders. A sample of 81 male and 210 female students was randomly selected. Two auditory evoked potential procedures were applied. The results indicated statistically significant differences in evoked potential responses between the genders. The results are interpreted against the background of sensory and neurological sources of the evoked potential responses and linked to the neurophysiological foundations of temperament. Opsomming: Gegrond op aanduidings in die literatuur van ’n assosiasie tussen temperamentskenmerke en die ontlokte potensiaal van die brein, sowel as aanduidings van geslagsverskille in sekere temperamentstrekke, was die doel van die huidige studie om te bepaal of ontloktepotensiaal-response ook tussen die geslagte onderskei. ’n Steekproef van 81 manlike en 210 vroulike studente is ewekansig geselekteer. Twee ouditiewe ontloktepotensiaal- prosedures is toegepas. Die resultate het op statisties beduidende verskille tussen die geslagte gedui. Die bevindinge word teen die agtergrond van die sensoriese en neurologiese oorsprong van ontloktepotensiaal–response geïnterpreteer en verbind aan die neurofisiologiese verankering van temperament.

  14. Die 'postmoderne' stempel in die Nuwe-Testamentiese hermeneutiek

    georiënteerde teorie en kritiek wat volgens Moore opbou tot 'n herhaling binne. Bybelnavorsing. Dit het reeds by Immanuel Kant begin. Sedert Kant is dit proble- maties cm die objek van kennis te beskou as iets wat kennis objektief in sigself bevat. Objektiwisme is prys gegee. Dialektiek het in die plek daarvan gekom. Die.

  15. duele verse sowel as die somtotaal die leser

    27 Jan 2006 ... selfs 'n landkaart afgedruk) terwyl dit ter- selfdertyd ver bo die lokale uitstyg. Die digter is sterk bewus van sy omgewing, geskiedenis en tradisies, maar veral van die algemene menslike kondisie wat binne hierdie referensiekader vergestalt word. Hy gebruik 'n bekende historiese slagveld as bundeltitel (en ...

  16. Die Leben Einsteins eine Reise durch die Geschichte der Physik

    Fiami

    2005-01-01

    Jeder kennt die Namen Einstein, Newton oder Galilei. aber was weiss man über sie? Hier ein Porträt Einsteins anhand von sechs Meilensteinen aus der Geschichte der Physik. Einstein tritt auf als Protagonist in verschiedenen Epochen und bei verschiedenen Entdeckungen, die die Welt verändert haben.

  17. DIE KONINGSBEDE AS ELEMENT IN DIE KRONINGSRITUEEL. By ...

    Test

    Die offerfees te Gibeon was 'n plegtigheid, waaraan geheel Israel deelgeneem het. Die duisend. "brandoffers" wat sowel Kon. as Kron. vermeld, sal wel opgevat moet word as „brandoffers en dankoffers", sodat daar vir die aanwesiges. *n groot feesmaaltyd aangerig is, vgl. I Kon. 3:15. n Sodanige maal- tyd verbind vors en ...

  18. Ruimtelike beplanning: die rol van die stads - en streeksbeplanner ...

    Ruimtelike beplanning: die rol van die stads - en streeksbeplanner in die saw. R Erasmus. Abstract. Since 1978 regional and town planners are employed in the SADF on a permanent basis as well as in the capacity of national service men. These men are all academically qualified and as such satisfy a need that developed ...

  19. n opinie oor die behaviouristiese siening versus die fenomenologie ...

    verband die eksperimente van Pavlov, Thorndike,. Skinner, Tolmann en Hull.) Fenomenologie. Die fenomenologie is 'n essensie-openbarende denkrigting. Dit impliseer'n denkende soektog na dit wat 'n besondere verskynsel of werklikheid maak juis dit wat dit is en nie iets anders nie. In die fenomenologiese antropologie ...

  20. Investigations of the boundary conditions of acicular ferrite formation in fast-quenched welded materials. Final report; Untersuchungen der Randbedingungen fuer die Bildung von 'acicular ferrite' in Schweissguetern bei schneller Abkuehlung. Schlussbericht

    Dilthey, U.; Biesenbach, M.

    2000-06-19

    The authors investigated the boundary conditions in which a fine-grained ferritic needle structure with sufficient low-temperature toughness is obtained in conditions of extreme heating and cooling. Alloy compositions and welding boundary conditions were investigated for laser welding, electron beam welding in a vacuum and electron beam welding at atmospheric pressure. [German] Im Rahmen dieser Arbeit soll untersucht werden, welche Randbedingungen erfuellt sein muessen, damit sich unter extremen Aufheiz- und Abkuehlbedingungen, wie sie bei den Strahlschweissverfahren vorliegen, ein feinkoerniges nadelferritisches Gefuege mit ausreichend hoher Tieftemperaturzaehigkeit bildet. Diesbezueglich ist fuer die Strahlschweissverfahren Laserstrahlschweissen, Elektronenstrahlschweissen im Vakuum und Elektronenstrahlschweissen unter Atmosphaerendruck zu ermitteln, welche Legierungszusammensetzungen diese Voraussetzungen erfuellen und wie sie unter realen Schweissbedingungen verwirklicht werden koennen. (orig.)

  1. Design, construction and experimental investigation of a Stirling refrigerator for freezing in supermarkets. Final report; Auslegung, Bau und experimentelle Untersuchung einer Stirling-Kaeltemaschine fuer die Tiefkuehlung in Supermaerkten. Schlussbericht

    Steimle, F.; Schikora, H.; Mai, M.; Siegel, A.

    2000-10-01

    Several theoretical investigations have shown that Stirling refrigerators could be a promising alternative for refrigeration at 'near-ambient' temperatures (above -40 C). These theoretical statements shall be validated in an actual research project by measurements taken from a Stirling refrigerator that is optimised for this range of temperature. In this paper first measurement results of this new developed Solo 161 Stirling refrigerator will be presented. Problems are investigated by detailed measurements. Possible improvements are described. (orig.) [German] Verschiedene theoretische Untersuchungen haben gezeigt, dass Stirling-Kaeltemaschinen eine interessante Alternative fuer die Kaelteerzeugung im sog. 'umgebungsnahen' Temperaturbereich (oberhalb von -40 C) darstellen koennten. In einem derzeit laufenden Forschungsvorhaben sollen diese theoretischen Untersuchungen durch Messungen an einer fuer diesen Temperaturbereich optimierten Stirling-Kaeltemaschine ueberprueft werden. In diesem Aufsatz werden erste Messergebnisse dieser neu entwickelten Solo 161 Stirling-Kaeltemaschine praesentiert. Anhand detaillierter Messergebnisse werden Schwachstellen lokalisiert und moegliche Verbesserungsmassnahmen beschrieben. (orig.)

  2. Die Vier Typen von Projektmanagern

    Lund Pedersen, Carsten; Ritter, Thomas

    2018-01-01

    Bevor Sie einem Mitarbeiter die Leitung eines Projekts anvertrauen, sollten Sie sich über dessen Managementstil klar werden. Passt dieser nicht zur Art des Vorhabens, wird er scheitern. So treffen Sie die richtige Wahl....

  3. Die historiese Jesus as wondenverker

    Biblical Association, te wete 'The social sciences and second Testament exegesis'. John Pilch is die leier van die Society of Biblical Literature se 'Social sciences and ..... Hollenbach, P 1982. ... Stauffer, E 1982. Jesus ... London: Collins.

  4. Development of a central final repository management for the coordination of the waste for Schacht Konrad from public authorities; Aufbau des zentralen Endlagerungsmanagements fuer die Koordination der Konrad-Abfaelle aus der oeffentlichen Hand

    Graffunder, Iris; Dominke-Bendix, Carola; Waldek, Achim [Energiewerke Nord GmbH (EWN), Eggenstein-Leopoldshafen (Germany). Betriebsstaette Karlsruhe; Wunn, Christoph [admoVa Consulting GmbH, Bad Camberg (Germany)

    2012-11-01

    The central final repository management is supposed to fulfill the following tasks: active collaboration of Konrad contract draft, signing of internal contracts and agreements, cooperation contract with GNS, cooperation with coordination authorities, inventory taking of wastes (existing inventory and prognosis) and interim storage capacities of public authorities, development of planning and management software, optimization of the final repository documentation, container management, logistics concept, long-term disposal planning and prognosis, planning and coordination of the annual waste amount, management and documentation of disposed waste allocation, coordination of transport schedules, consulting service for waste obligations (final repository requirements, product control, documentation).

  5. Education and Caste in India

    Chauhan, Chandra Pal Singh

    2008-01-01

    This paper analyses the policy of reservation for lower castes in India. This policy is similar to that of affirmative action in the United States. The paper provides a brief overview of the caste system and discusses the types of groups that are eligible for reservation, based on data from government reports. The stance of this paper is that…

  6. Die verband tussen werknemertevredenheid en organisasieverbondenheid

    A. A. S. Pretorius

    2004-10-01

    Full Text Available The relationship between employee satisfaction and organisational commitment. The primary goal of the study is to determine whether a relationship exists between employee satisfaction and organisational commitment. A secondary goal is to determine whether any biographical variables mediate this relationship. Standardised instruments were used for operationalising these two contructs. A sample of convenience yielded 167 respondents out of a sampling frame of 300 employees from a financial organisation. Only 145 respondents returned fully completed questionnaires that were used for final analysis. Responses from both questionnaires were subjected to a factor and item analysis. A statistically significant relation between employee satisfaction and organisational commitment was found. The implications of the findings are discussed further. Opsomming Die primêre doel van die studie is om vas te stel of daar ’n verband bestaan tussen werknemertevredenheid en organisasieverbondenheid. ’n Sekondêre oogmerk is om te bepaal of enige biografiese veranderlikes hierdie verband medieer. Gestandaardiseerde instrumente is gebruik om hierdie twee konstrukte te operasionaliseer. ’n Gerieflikheidsteekproef het 167 respondente uit ’n steekproefraamwerk van 300 werknemers van ’n finansiële instelling opgelewer. Slegs 145 respondente het volledig voltooide vraelyste terugbesorg, wat vir finale ontleding gebruik is. Response op albei vraelyste is aan ’n faktor- en itemontleding onderwerp. ’n Statisties-beduidende verband tussen werknemertevredenheid en organisasieverbondenheid is gevind. Die implikasies van die bevindinge word verder bespreek.

  7. Precision die design by the die expansion method

    Ibhadode, A O Akii

    2009-01-01

    This book presents a new method for the design of the precision dies used in cold-forging, extrusion and drawing processes. The method is based upon die expansion, and attempts to provide a clear-cut theoretical basis for the selection of critical die dimensions for this group of precision dies when the tolerance on product diameter (or thickness) is specified. It also presents a procedure for selecting the minimum-production-cost die from among a set of design alternatives. The mathematical content of the book is relatively simple and will present no difficulty to those who have taken basic c

  8. Colour Metallography of Cast Iron

    Zhou Jiyang

    2009-05-01

    Full Text Available Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc. Experts and engineers studying and producing iron castings all around world extremely concern this serious challenge. Over more than 30 years, a great of research work has been carried out on how to further improve its property, expand its application and combine cast iron technology with some hi-techs (for example, computer technology. Nevertheless, cast iron is a multi-element and multi-phase alloy and has complex and variety of structures and still has great development potential in structure and property. For further studying and developing cast iron, theoretical research work is important promise, and the study on solidification process and control mechanism of graphite morphology is fundamental for improving property of cast iron and developing new type of cast iron.Metallography of cast iron normally includes two sections: liquid phase transformation and solid phase transformation. The book, Colour Metallography of Cast Iron , uses colour metallography technique to study solidification structures of cast irons: graphite, carbides, austenite and eutectics; and focuses on solidification processes. With progress of modern solidification theory, the control of material solidification process becomes important measure for improving traditionalmaterials and developing new materials. Solidification structure not only influences mechanical and physical properties of cast iron, but also affects its internal quality. The book uses a large amount of colour photos to describe the formation of solidification structures and their relations. Crystallization phenomena, which cannot be displayed with traditional metallography, are presented and more phase transformation information is obtained from these colour

  9. Die Dokter-Pasient Rolverwantskap

    17 Aug 1974 ... en as sodanig 'n ral sped in die persoon se siektegedrag en uiteindelike patroon van hulpsoeke. SIEKEROL EN SOSIALISERING IN DIE. PASIENTROL ..... more cumulative, resulting in a more gradual social and professional maturation.' Vit die voorafgaande word dit duidelik dat Dewy se pragmatiese ...

  10. prosesseringsmetodes op die voedingswaarde van

    gebring is, kon geen betekenisvolle verskille tussen die drie monsters gevind word nie. Volgens Opstvedt (1976) kan ME waardes ook dien as 'n kriteria van proteien- kwaliteit, hoofsaaklik a.g.v. die verhoogde stikstofuit- skeiding in die urine wat sal plaasvind a.g.v. beskadiging van aminosure. De Groote (1968) het gevind ...

  11. DIE SAW SE ROL IN SWA

    wei die verdediging van die landsgrense teen 'n vyand wat die orde, gesag, vrede, stabiliteit en welvaart in Suidwes-Afrika en die Republiek van. Suid-Afrika wil vernietig. Hierdie oorlog moet nie ge'lsoleerd gesien word nie, maar in perspektief geplaas word teen die agtergrond van 'n nag groter konflik, naamlik die van die ...

  12. Die Subjektiewe en Objektiewe doelwitte van Arbeid

    T. H. Veldsman

    1982-11-01

    Die artikel gee aandag aan die subjektiewe en objektiewe doelwitte van arbeid. Hul plek en funksie binne 'n voorgestelde geïntegreerde motiveringsmodel word eerstens aangedui. Vervolgens word die verwantskap tussen die twee doelwitte uitgelig, gevolg deur 'n bespreking van die aard van die objektiewe doel. Laastens word die invloed van moderne arbeid op hierdie doelwitte uitgestippel.

  13. DIE EKSISTENSIEFILOSOFIE VAN KARL JASPERS. ENKELE ...

    Test

    Kierkegaard en Nietzsche, Max Weber en Dilthey, om maar enkeles te noem, en 5.) Jaspers se persoonlike beskouing oor die roe ping en die taak van die Filosofie, sy aanvoeling van die filosofiese problematiek en sy grondhouding teenoor die eksistensiële verbonden- hede. Die woord van Fichte, naamlik dat die Filosofie ...

  14. Fatigue life of the casting-magnesium alloy AZ91

    Eisenmeier, G.; Mughrabi, H.; Holzwarth, B.; Hoeppel, H.W.; Ding, H.Z.

    2000-01-01

    The cyclic deformation behaviour of the die-casting magnesium alloy AZ91 was investigated at constant total strain amplitudes between 1.4 x 10 -3 and 2 x 10 -2 at room temperature (20 C) and at 130 C. At low total strain amplitudes, a weak cyclic softening at the beginning of the fatigue tests is followed by cyclic hardening, whereas at high total strain amplitudes a strong cyclic hardening occurs throughout. The fatigue lives at 130 C are slightly longer at high strain amplitudes but shorter at low strain amplitudes than at room temperature. The fatigue life data for both temperatures can be described well by the laws of Manson-Coffin and Basquin. The microstructural investigations performed show the strong influence of several microstructural features on the initiation and propagation of fatigue cracks. In order to understand the fatigue crack propagation behaviour, fatigue tests were interrupted at certain numbers of cycles in order to make replicas of the surface of the samples. It could be verified that crack propagation occurs mainly by the coalescence of smaller cracks. Furthermore, unloading tests, performed within a closed cycle, were carried out in order to capture the changes of stiffness (compliance) during a closed cycle with the aim to ascertain the damage evolution occurring during the fatigue tests and to determine the stresses at which the cracks open and close. Finally, two-step fatigue tests were carried out with the objective to quantify deviations from the linear damage rule (LDR) of Palmgren and Miner. The results obtained in this study will be used to formulate a microstructurally based life-prediction concept for single-step as well as for two-step fatigue loading. (orig.)

  15. First Results of Energy Saving at Process Redesign of Die Forging Al-Alloys

    Pepelnjak, Tomaz; Kuzman, Karl; Kokol, Anton

    2011-01-01

    The contribution deals with eco-friendly solutions for shortened production chains of forging light alloys. During the die forging operations a remarkable amount of material goes into the flash and later on into chips during finish machining. These low value side products are rich with embedded energy therefore recycling or reprocessing could be very energy saving procedure.In cooperation with a die forging company a shortened reprocessing cycle has been studied starting from re-melting the forging flash and without additional heating to cast preforms for subsequent die forging. As such preforms have not as good formability characteristics as those done from extruded billets the isothermal forging process has been adopted. First results showed that without cracks and other defects the formability is sufficient for a broad spectrum of forgings.To improve the formability a homogenization process of cast preforms has been implemented. As the process started immediately after casting, amount of additional energy for heating was minimized. To reduce voids forging process was redesigned in a way to assure greater hydrostatic pressures in parts during forging. First results were promising therefore research is going towards improving processes without adding significantly more energy as it is needed for casting with homogenization and die forging.

  16. Accuracy of ringless casting and accelerated wax-elimination technique: a comparative in vitro study.

    Prasad, Rahul; Al-Keraif, Abdulaziz Abdullah; Kathuria, Nidhi; Gandhi, P V; Bhide, S V

    2014-02-01

    The purpose of this study was to determine whether the ringless casting and accelerated wax-elimination techniques can be combined to offer a cost-effective, clinically acceptable, and time-saving alternative for fabricating single unit castings in fixed prosthodontics. Sixty standardized wax copings were fabricated on a type IV stone replica of a stainless steel die. The wax patterns were divided into four groups. The first group was cast using the ringless investment technique and conventional wax-elimination method; the second group was cast using the ringless investment technique and accelerated wax-elimination method; the third group was cast using the conventional metal ring investment technique and conventional wax-elimination method; the fourth group was cast using the metal ring investment technique and accelerated wax-elimination method. The vertical marginal gap was measured at four sites per specimen, using a digital optical microscope at 100× magnification. The results were analyzed using two-way ANOVA to determine statistical significance. The vertical marginal gaps of castings fabricated using the ringless technique (76.98 ± 7.59 μm) were significantly less (p castings fabricated using the conventional metal ring technique (138.44 ± 28.59 μm); however, the vertical marginal gaps of the conventional (102.63 ± 36.12 μm) and accelerated wax-elimination (112.79 ± 38.34 μm) castings were not statistically significant (p > 0.05). The ringless investment technique can produce castings with higher accuracy and can be favorably combined with the accelerated wax-elimination method as a vital alternative to the time-consuming conventional technique of casting restorations in fixed prosthodontics. © 2013 by the American College of Prosthodontists.

  17. Successful magnet quench test for CAST.

    Brice Maximilien

    2002-01-01

    The CERN Axion Solar Telescope (CAST) consists of a prototype LHC dipole magnet with photon detectors at each end. It searches for very weakly interacting neutral particles called axions, which should originate in the core of the Sun. The telescope, located at Point 8, can move vertically within its wheeled platform, which travels horizontally along tracks in the floor. In this way, the telescope can view the Sun at sunrise through one end and at sunset through the other end. It has been cooled down to below 1.8 K and reached ~95% of its final magnetic field of 9 tesla before a quench was induced to test the whole cryogenic system under such conditions. The cryogenic system responded as expected to the magnet quench and CAST is now ready to start its three-year search for solar axions. Photos 01 & 02 : Members of the LHC cryogenics team pose in front of the axion telescope on the day of the first quench test, together with some of the CAST collaboration.

  18. Analytic studies on pollutant deposition through domestic coal combustion - influence of the current structural change on pollution in an urban region. Final report; Analytische Untersuchungen zum Schadstoffeintrag durch den Hausbrand - Auswirkungen des gegenwaertigen Strukturwandels auf die urbane Belastungssituation. Abschlussbericht

    Engewald, W.; Knobloch, T.; Asperger, A.

    1996-12-31

    Relevanz (u.a. als Vorlaeufersubstanzen fuer bodennahes Ozon und andere Oxidantien). Hieraus ergaben sich fuer das Teilprojekt die folgenden methodischen Schwerpunkte: - Entwicklung und Erprobung einer Probenahme- und Analysenmethode zur Bestimmung eines moeglichst breiten Spektrums von Spuren fluechtiger organischer Verbindungen im Immissionsbereich - Erarbeiten einer Messstrategie, die Ergebnisse hoher Repraesentanz und Aussagekraft gewaehrleistet - Installation und Betrieb von Immissionsmessplaetzen in ausgewaehlten, fuer Leipzig typischen Stadtstrukturen - Durchfuehrung jeweils mehrwoechiger Messkampagnen an den ausgewaehlten Standorten in Sommer- und Winterperioden. (orig./MSK)

  19. Dying with dignity.

    Madan, T N

    1992-08-01

    Death is a theme of central importance in all cultures, but the manner in which it is interpreted varies from society to society. Even so, traditional cultures, including Christian, Hindu and Jain religious traditions, exhibited a positive attitude to death and did not look upon it in a dualistic framework of good vs bad, or desirable vs undesirable. Nor was pessimism the dominant mood in their thinking about death itself. A fundamental paradigm shift occurred in the West in the eighteenth century when death was desacralized and transformed into a secular event amenable to human manipulation. From those early beginnings, dying and death have been thoroughly medicalized and brought under the purview of high technology in the twentieth century. Once death is seen as a problem for professional management, the hospital displaces the home, and specialists with different kinds and degrees of expertise take over from the family. Everyday speech and the religious idiom yield place to medical jargon. The subject (an ageing, sick or dying person) becomes the object of this make-believe yet real world. As the object of others' professional control, he or she loses the freedom of self-assessment, expression and choice. Or, he or she may be expected to choose when no longer able to do so. Thus, not only freedom but dignity also is lost, and lawyers join doctors in crisis manipulation and perpetuation. Although the modern medical culture has originated in the West, it has gradually spread to all parts of the world, subjugating other kinds of medical knowledge and other attitudes to dying and death.(ABSTRACT TRUNCATED AT 250 WORDS)

  20. Sal die ‘ewolusie’ vanaf biologie na lewenswetenskappe ‘uitsterwing’ van die vakgebied voorkom?

    Johanna G. Ferreira

    2012-03-01

    Full Text Available In hierdie artikel word die wysiging van die skoolvak van ‘biologie’ na ‘lewenswetenskappe’ bespreek, asook die gepaardgaande en verwagte implikasies van die verandering. Die vraag word gestel of die beoogde wysiging wel noemenswaardig is en of dit enigsins ‘n verskil aan die dalende belangstelling in die lewenswetenskappe op tersiêre vlak sal maak. Die wysigings in die nuwe kurrikula verhoog die relevansie van die vakinhoud vir leerders en vir die gemeenskap, maar sekere kwessies kry nie aandag nie. Voorstelle word gemaak om die kurrikulum te wysig en onderrigmetodes aan te pas om die nodige vaardighede by leerders te vestig.

  1. enkele fasette van die problematiek van die akademikus by die skryf

    Om verskeie redes het dit van die allergrootste belong geword dot 'n his- tories korrekte, wetenskaplike weerga- we van bogenoemde gebeure opge- teken moet word. Die sluier, in sommige gevalle am logiese redes toegepas, moes eenvoudig gelig word am gebeure wat die gewone man op stroot in Suid-Afrika dikwels ...

  2. Die Defects and Die Corrections in Metal Extrusion

    Sayyad Zahid Qamar

    2018-05-01

    Full Text Available Extrusion is a very popular and multi-faceted manufacturing process. A large number of products for the automotive, aerospace, and construction sectors are produced through aluminum extrusion. Many defects in the extruded products occur because of the conditions of the dies and tooling. The problems in dies can be due to material issues, design and manufacturing, or severe usage. They can be avoided by maintaining the billet quality, by controlling the extrusion process parameters, and through routine maintenance. Die problems that occur on a day-to-day basis are mostly repairable and are rectified through various types of die correction operations. These defects and repair operations have not been reported in detail in the published literature. The current paper presents an in-depth description of repairable die defects and related die correction operations in metal extrusion. All major die defects are defined and classified, and their causes, preventive measures, and die correction operations are described. A brief frequency-based statistical study of die defects is also carried out to identify the most frequent die corrections. This work can be of direct benefit to plant engineers and operators and to researchers and academics in the field of metal extrusion.

  3. Investment casting of beta titanium alloys for aerospace applications

    Wheeler, D.A.; Cianci, M.S.; Vogt, R.G.

    1993-01-01

    The process of investment casting offers the ability to produce complex titanium components with minimal finish machining, thereby reducing their overall manufacturing cost. While aerospace applications for cast titanium have focused primarily on alpha+beta alloys, recent interest in higher strength beta alloys has prompted an examination of their suitability for investment casting. In this paper, the processing characteristics and mechanical proper-ties of Ti-1 5V-3Cr-3Al-3Sn, Ti-3Al-8V-6Cr-4Mo-4Zr, and Ti-15Mo-3Nb-3Al-0.2Si (wt.%) will be discussed. It will be shown that all three alloy compositions are readily processed using only slight modifications from current Ti-6Al-4V (wt.%) production operations. In addition, the mechanical properties of the cast product form can be manipulated through heat treatment and compare quite favorably with typical properties obtained in wrought beta titanium products. Finally, several demonstration castings are reviewed which illustrate the shape-making capabilities of the investment casting approach for beta titanium alloys

  4. Integrated design of castings: effect of porosity on mechanical performance

    Hardin, R A; Beckermann, C

    2012-01-01

    Porosity can significantly reduce the strength and durability of castings in service. An integrated design approach has been developed where casting simulation is combined with mechanical performance simulations. Predictions of the porosity distribution from the casting process simulation are transferred to and used in stress and fatigue life simulations. Thus, the effect of casting quality on service performance can be evaluated. Results of a study are presented where the measured porosity distribution in cast steel specimens is transferred to an elasto-plastic finite-element stress analysis model. Methods are developed to locally reduce the mechanical properties according to the porosity present, without having to resolve individual pores. Plastic deformation is modeled using porous metal plasticity theory. The predictions are compared to tensile measurements performed on the specimens. The complex deformations and the reductions in the ductility of the specimens due to porosity are predicted well. The predicted stresses are transferred to a fatigue analysis code that takes the porosity distribution into account as well. The measured and predicted fatigue lives are also in good agreement. Finally, the results of a case study are presented that illustrate the utility of the present integrated approach in optimizing the design of a steel casting.

  5. Die hermeneutiek van gereformeerde kerkreg

    Andries le Roux du Plooy

    2012-10-01

    Full Text Available Die artikel het op die belangrikheid en noodsaaklikheid van ‘n hermeneutiek vir die gereformeerde kerkreg gefokus. Die kerkregtelike dokument wat besonderlik ter sake was, is die kerkorde van die Gereformeerde kerke in Suid-Afrika, met sy besondere band met die Dordtse kerkorde van 1618 en 1619. Agtereenvolgens is aandag gegee aan die volgende aspekte soos (1 die eiesoortige aard van ‘n kerkorde as ‘n teologiese dokument en teks, in onderskeiding van regsdokumente; (2 die aard van die hermeneutiek van kerkreg; (3 enkele teorieë oor die interpretasie of uitleg van tekste, veral regstekste en (4 normatiewe vooronderstellings en reëls vir die interpretasie en verstaan van die teks en artikels van die kerkorde asook besluite van kerklike vergaderinge. Die gevolgtrekking was dat weinig indringende navorsing gedoen is oor die saak van hermeneutiek vir kerkreg, hoewel dit noodsaaklik is. Duidelike hermeneutiese reëls is gesuggereer en verduidelik, wat sou kon meehelp dat kerke en kerklike vergaderinge die artikels van die kerkorde asook besluite en reglemente wat daarop berus het, kan interpreteer en toepas. The hermeneutics of reformed church polity. The article focused on the importance and urgency of a design for reformed hermeneutics on church polity. The Church Order referred to in the article is the Church Order of the Reformed Churches in South Africa, which are closely related to the Church Order of Dordt of 1618 and 1619. The following aspects received attention namely (1  the unique character of a Church Order, in comparison to and distinguished from legal documents and statutes; (2 the character and nature of hermeneutics of church polity; (3 theories of interpretation in the common law tradition and their relevance to church polity and (4 normative presuppositions and marks for the interpretation and understanding of the text and articles of the Church Order, as well as the resolutions of church assemblies. It was found that

  6. Rate of solidification of aluminium casting in varying wall thickness of cylindrical metallic moulds

    Katsina Christopher BALA

    2014-02-01

    Full Text Available The quality of final casting mainly depends on the rate of solidification as rapid solidification produces fine grains structures with better mechanical properties. The analysis of heat transfer during the casting and solidification of aluminium alloy as well as the experimental investigation of the rate of solidification in varying thicknesses of cylindrical metallic mould was carried out. The temperature variation with time of the casting was recorded from which cooling curves were obtained for the determination of solidification time of the cast. The results showed that as the cylindrical mould thickness increases the solidification time decreases due to the chilling effect of the mould.

  7. Marginal accuracy of nickel chromium copings fabricated by conventional and accelerated casting procedures, produced with ringless and metal ring investment procedures: A comparative in vitro study.

    Alex, Deepa; Shetty, Y Bharath; Miranda, Glynis Anita; Prabhu, M Bharath; Karkera, Reshma

    2015-01-01

    Conventional investing and casting techniques are time-consuming and usually requires 2-4 h for completion. Accelerated nonstandard, casting techniques have been reported to achieve similar quality results in significantly less time, namely, in 30-40 min. During casting, it is essential to achieve compensation for the shrinkage of solidifying alloy by investment expansion. The metal casting ring restricts the thermal expansion of investment because the thermal expansion of the ring is lesser than that of the investment. The use of casting ring was challenged with the introduction of the ringless technique. A total of 40 test samples of nickel chromium (Ni-Cr) cast copings were obtained from the patterns fabricated using inlay casting wax. The 20 wax patterns were invested using metal ring and 20 wax patterns were invested using the ringless investment system. Of both the groups, 10 samples underwent conventional casting, and the other 10 underwent accelerated casting. The patterns were casted using the induction casting technique. All the test samples of cast copings were evaluated for vertical marginal gaps at four points on the die employing a stereo optical microscope. The vertical marginal discrepancy data obtained were tabulated. Mean and standard deviations were obtained. Vertical discrepancies were analyzed using analysis of variance and Tukey honestly significantly different. The data obtained were found to be very highly significant (P cast copings fabricated with the conventional casting using ringless investment system showed significantly better marginal fit than that of cast copings fabricated from conventional and accelerated casting with metal ring investment and accelerated casting using ringless investment since those copings had shown the least vertical marginal discrepancies among the four methods evaluated in this study.

  8. Die verband tussen lokus van beheer en die werks prestasie van swart bemarkers in die lewensversekeringsbedryf

    E. L. Coetzer

    1997-06-01

    Full Text Available The relationship between locus of control and the work performance of black marketers in the life assurance industry. The aim of the study was to establish the relationship between locus of control and the work performance of black marketers in the life assurance industry. These constructs were selected by virtue of the lack of empirical research regarding the assumed relationship between them. The Locus of Control Scale of Schepers (1995 was used for measuring locus of control. Work performance was measured by the commission earned per month by the marketer, the number of policies generated by the marketer, as well as the percentage of lapsed policies. The relevant measurements were obtained in respect of a sample of 149 black marketing personnel. The results indicated a modest but statistically significant relationship between external locus of control and the work performance of black marketers. Opsomming Die doel van die studie was om die verband tussen lokus van beheer en die werksprestasie van swart bemarkers in die lewensversekeringsbedryf te bepaal. Hierdie konstrukte is gekies op grond van die gebrek aan empiriese navorsing rakende die veronderstelde verband tussen genoemde konstrukte. Die Lokus van Beheer-vraelys van Schepers (1995 is in die meting van lokus van beheer gebruik. Werksprestasie is aan die hand van kommissie per maand verdien, aantal polisse gegenereer deur 'n bemarker en die persentasie vervalde polisse, gemeet. Die tersaaklike metinge is verkry ten opsigte van 'n steekproef van 149 swart bemarkers. Die resultate toon 'n klein, dog statisties beduidende verband tussen eksterne lokus van beheer en die werksprestasie van swart bemarkers in die lewensversekeringsbedryf.

  9. Is die ortodoksie se verstaan van die sondeval belemmerend vir die gesprek tussen teologie en natuurwetenskap?

    Johan Buitendag

    2012-11-01

    Full Text Available In hierdie artikel is betoog dat die Gereformeerde Ortodoksie se begrip van die sondeval ’n  belemmering  was  vir  die  gesprek  tussen  teologie  en  natuurwetenskap.  Die  rede hiervoor was dat dit ten eerste ’n bepaalde verstaan van liniêre tyd nahou en ten tweede dat dit ’n bonatuurlike ingryp veronderstel het. Albei hierdie aspekte het die debat onnodig problematiseer. Die argument is ontwikkel deur eerstens die probleem te definieer, gevolg deur ’n uiteensetting van die standpunte van Augustinus en Calvyn onderskeidelik oor die sondeval. As ’n heuristiese sleutel is die konsepte van infralapsarisme en supralapsarisme aangewend om die tema te ontleed. Die artikel is afgesluit met die oortuiging dat die imago Dei ’n beliggaamde menslike persoon is wat biologies in die geskiedenis in terme van selfbewussyn en morele verantwoordelikheid ontluik het. Is the Orthodoxy’s notion of the Fall inhibitory for the dialogue between theology and science? In this article it was argued that the Reformed Orthodoxy’s interpretation of the Fall had become an impediment in the dialogue between theology and science. The reason was that it assumed firstly a specific understanding of linear time and secondly a metaphysical intervention. Both events were unnecessarily problematising the debate. The argument was deployed by stating the problem, followed by an exposition of the views of Augustine and Calvin on the Fall. As a heuristic key, the concepts of infralapsarism and supralapsarism were applied respectively to analyse the topic. The article concluded with the conviction that the imago Dei is an embodied human person that had biologically emerged in history as a center of self-awareness, and moral responsibility.

  10. Sixty Years of Casting Research

    Campbell, John

    2015-11-01

    The 60 years of solidification research since the publication of Chalmer's constitutional undercooling in 1953 has been a dramatic advance of understanding which has and continues to be an inspiration. In contrast, 60 years of casting research has seen mixed fortunes. One of its success stories relates to improvements in inoculation of gray irons, and another to the discovery of spheroidal graphite iron, although both of these can be classified as metallurgical rather than casting advances. It is suggested that true casting advances have dated from the author's lab in 1992 when a critical surface turbulence condition was defined for the first time. These last 20 years have seen the surface entrainment issues of castings developed to a sufficient sophistication to revolutionize the performance of light alloy and steel foundries. However, there is still a long way to go, with large sections of the steel and Ni-base casting industries still in denial that casting defects are important or even exist. The result has been that special ingots are still cast poorly, and shaped casting operations have suffered massive losses. For secondary melted and cast materials, electro-slag remelting has the potential to be much superior to expensive vacuum arc remelting, which has cost our aerospace and defense industries dearly over the years. This failure to address and upgrade our processing of liquid metals is a serious concern, since the principle entrainment defect, the bifilm, is seen as the principle initiator of cracks in metals; in general, bifilms are the Griffith cracks that initiate failures by cracking. A new generation of crack resistant metals and engineering structures can now be envisaged.

  11. Sedimentêre omgewings van die Inhaca-eilandstelsel met spesiale verwysing na die petrografiese en geochemiese eienskappe van die sedimente spesiale verwysing na die petrografiese en geochemiese eienskappe van die sedimente

    Marieke Peché

    2011-09-01

    Full Text Available Die Inhaca-eilandstelsel is geleë langs die suidooskus van Mosambiek. Die oostekant van die stelsel grens aan die Indiese Oseaan en die westekant aan die Baai van Maputo. Hierdie eilandstelsel bestaan uit Inhaca- en Portugese eiland, asook ’n groep sandbanke wat van die noordlike punt van Inhaca na Portugese eiland strek. Die doel van hierdie studie is om die verskillende moderne en oer-sedimentêre omgewings op die eilandstelsel te identifiseer en te beskryf, die invloed van getye en golfaksie op die moderne sedimentêre omgewing vas te stel en die geochemiese en petrografiese samestelling van die geologiese eenhede te bepaal.

  12. Strip casting apparatus and method

    Williams, R.S.; Baker, D.F.

    1988-09-20

    Strip casting apparatus including a molten-metal-holding container and a nozzle to deposit molten metal onto a moving chill drum to directly cast continuous metallic strip. The nozzle body includes a slot bounded between a back and a front lip. The slot width exceeds about 20 times the gap distance between the nozzle and the chill drum surface. Preferably, the slot width exceeds 0.5 inch. This method of strip casting minimizes pressure drop, insuring better metal-to-chill-drum contact which promotes heat transfer and results in a better quality metallic strip. 6 figs.

  13. Die noodsaak van kultuurdifferensiasie in die onderwys

    H. J. Steyn

    1985-03-01

    Full Text Available In this article the author discusses the necessity of cultural differentiation in education. Following a brief introduction in which various viewpoints are compared and contrasted, he outlines the concepts of culture, education and educational system, following this by a discussion of the interaction between culture and the educational system. He further illuminates this by referring to a number of the modes of existence of educational systems. In the physical manifestation of an educational system three main components can be distinguished, viz. educational policy, educational administration and execution of education. After a close reasoning and explication of these points, he comes to the conclusion that the educational system also belongs to culture, in that the educational system is man's most comprehensive cultural product in the field of education and teaching. This leads to the second part of the article where close attention is paid to the links between culture and the aims of education, between culture and the cirriculum. He comes to the final conclusion then that cultural differentiation is essential in education. Each country with a multi-cultural society has to work hard, through research and honest reflection, to enrich and to refine the existing practices in education.

  14. NUMERICAL MODELING OF HARDENING OF UNINTERRUPTEDLY-CASTED BRONZE CASTING

    E. I. Marukovich

    2009-01-01

    Full Text Available The three-dimensional numerical model for calculation of thermal fields during solidification of continuously casted bronze casting is developed. Coefficients of heat transfer on borders of calculation areas on the basis of the solution of inverse heat transfer conduction problem are determined. The analysis of thermal fields, depending on loop variables of drawing and the sizes of not cooled zone of crystallizer is curried out.

  15. Die vangnet van die woord: forensies-linguistiese getuienis in 'n ...

    Een van die redes daarvoor is waarskynlik die gepaardgaande sleurwerk verbonde aan die verwerking van die betrokke taaldata — iets wat egter deur die onlangse meteoriese vooruitgang in tegnologiese tegnieke op die agtergrond geskuif is en nuwe moontlikhede na vore laat kom het. In die lig van die kompleksiteit van ...

  16. het om die Woord van God aan die gemeente te bedien. A. D. P ont ...

    Test

    Sizoo vertel met die vlotheid van die ervare skrywer en die ver antwoordelikheid van die wetenskaplike ... Maar in stiptelike trou aan die feitelikheid, verlaat die skrywer hom uitsluitlik op die outentieke bronne om ... de leser; in sy rykdom van gegewens en wetenskaplike betroubaarheid kan dit met vrug gelees word deur die ...

  17. Die invloed van herbivorie en vuur op die oorlewing van sekere meerjarige kruide langs die Sabierivier, Kruger Nasionale Park

    H. Myburgh

    2012-03-01

    Full Text Available Die groot vloede wat in die jaar 2000 in die Kruger Nasionale Park plaasgevind het, het dierivieroewerplantegroei versteur. Dit het die geleentheid gebied om heinings op te rig langsdie Sabierivier om herbivore uit sekere gebiede uit te sluit en sodoende die herstel van die rivieroewerekosisteme te monitor.

  18. Die heelal en sy onstaan (II

    D. J. Van Rooy

    1952-03-01

    Full Text Available Ons kennis en wetenskap van die hemelliggame word volkome bepaal deur die lig wat ons van hulle ontvang, d.w.s. as ons die feite wat die Bybel daaromtrent meedeel, buite rekening laat.

  19. Versoening tussen leerders: Is parallelmediumskole die antwoord op die rassismeprobleem?

    Du Plessis, Elize; Marais, Petro

    2017-01-01

    Die Suid-Afrikaanse Grondwet stel dit duidelik dat enige vorm van diskriminasie nie toegelaat mag word nie. In ons skole beteken dit dat elke leerder ʼn reg het op goeie opvoeding en ʼn veilige skoolomgewing. Die fokus van hierdie navorsing is gerig op bestaande parallelmediumskole. Die uiteindelike vraagstuk is dus hoe multikulturele onderwys bevorder word en hoe rassisme aangespreek kan word? As teoretiese raamwerk is Kohlsberg se kognitiewe ontwikkelingsbenadering en Whitehouse se univerele ...

  20. Die ontmaskering van die bose: Eksegetiese perspektiewe op ...

    p1243322

    2 Yarbro Collins (1983) bied tans nog die beste agtergrond vir 'n besinning oor geweld in ..... John's grammatical howlers are intentionally designed to alert listerners ..... 26 In die Nuwe Testament word Paul se snydende opmerking teenoor die Korintiërs as ..... rnt g0r`m nh8 ldfhrs`}m du sg}u fg}u + n2sh d/m sg>}} e`ql`jdh.

  1. Anodization of cast aluminium alloys produced by different casting methods

    K. Labisz

    2008-08-01

    Full Text Available In this paper the usability of two casting methods, of sand and high pressure cast for the anodization of AlSi12 and AlSi9Cu3 aluminium cast alloys was investigated. With defined anodization parameters like electrolyte composition and temperature, current type and value a anodic alumina surface layer was produced. The quality, size and properties of the anodic layer was investigated after the anodization of the chosen aluminium cast alloys. The Alumina layer was observed used light microscope, also the mechanical properties were measured as well the abrasive wear test was made with using ABR-8251 equipment. The researches included analyze of the influence of chemical composition, geometry and roughness of anodic layer obtained on aluminum casts. Conducted investigations shows the areas of later researches, especially in the direction of the possible, next optimization anodization process of aluminum casting alloys, for example in the range of raising resistance on corrosion to achieve a suitable anodic surface layer on elements for increasing applications in the aggressive environment for example as materials on working building constructions, elements in electronics and construction parts in air and automotive industry.

  2. Open die forging of large shafts with porosity defects – physical and numerical modelling

    Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

    2013-01-01

    The aim and scope of this paper is centered to analyze the influence of the geometry of V-shaped dies on the closure of internal centerline porosity defects in ingots during multistep open-die forging. The investigation is performed with small scale physical models made from lead using V-shaped d......The aim and scope of this paper is centered to analyze the influence of the geometry of V-shaped dies on the closure of internal centerline porosity defects in ingots during multistep open-die forging. The investigation is performed with small scale physical models made from lead using V......-shaped dies with 90o and 120o and a reference pair of flat parallel platens. Holes drilled through the center of these preforms are produced to mimic centerline porosity in full scale cast ingots and intermediate rotation of the preforms replicate a multi-stage forging sequence under laboratory testing...

  3. Accurate defect die placement and nuisance defect reduction for reticle die-to-die inspections

    Wen, Vincent; Huang, L. R.; Lin, C. J.; Tseng, Y. N.; Huang, W. H.; Tuo, Laurent C.; Wylie, Mark; Chen, Ellison; Wang, Elvik; Glasser, Joshua; Kelkar, Amrish; Wu, David

    2015-10-01

    Die-to-die reticle inspections are among the simplest and most sensitive reticle inspections because of the use of an identical-design neighboring-die for the reference image. However, this inspection mode can have two key disadvantages: (1) The location of the defect is indeterminate because it is unclear to the inspector whether the test or reference image is defective; and (2) nuisance and false defects from mask manufacturing noise and tool optical variation can limit the usable sensitivity. The use of a new sequencing approach for a die-to-die inspection can resolve these issues without any additional scan time, without sacrifice in sensitivity requirement, and with a manageable increase in computation load. In this paper we explore another approach for die-to-die inspections using a new method of defect processing and sequencing. Utilizing die-to-die double arbitration during defect detection has been proven through extensive testing to generate accurate placement of the defect in the correct die to ensure efficient defect disposition at the AIMS step. The use of this method maintained the required inspection sensitivity for mask quality as verified with programmed-defectmask qualification and then further validated with production masks comparing the current inspection approach to the new method. Furthermore, this approach can significantly reduce the total number of defects that need to be reviewed by essentially eliminating the nuisance and false defects that can result from a die-to-die inspection. This "double-win" will significantly reduce the effort in classifying a die-to-die inspection result and will lead to improved cycle times.

  4. Die pastorale sielkundige as diakonale pastor

    A. J. Smuts

    1985-08-01

    Full Text Available In die bedieningspatroon van die Ned. Geref. Kerk het die pastorale sielkundige die afgelope aantal jare steeds meer op die voorgrond begin tree. Hy is egter 'n problematiese figuur, wie se identiteit van meer as een kant onder bespreking is. In ander lande, selfs in die VSA waar die kerk veel gebruik maak van die sielkunde, is dit moeilik om 'n presiese parallel vir hom te vind. Sowel binne as buite die kerk word hy deur sommige bevraagteken. Daarom is dit noodsaaklik om vanuit die teologie te kyk na die werk wat hy doen.

  5. The final disposal of radioactive wastes as social, political and scientific project - an introduction; Ewigkeitslasten. Die ''Endlagerung'' radioaktiver Abfaelle als soziales, politisches und wissenschaftliches Projekt - eine Einfuehrung

    Brunnengraeber, Achim

    2015-07-01

    The nuclear power production that was productive for two generations produces radioactive wastes that will be a hazardous and financial burden for many future generations. Science, politics, industry and the society are responsible to find a successful solution for the project of final disposal of radioactive wastes. With the fast development of renewable energies with the perspectives of sustainability and other advantages nuclear power will not have a remarkable future. The search for a final repository site is a tremendous governmental, economic and public challenge but can also be seen as a social chance. Democracy could be enforced by this process, public commitment, transparency, co-determination, confidence in political processes are indispensible premises.

  6. Tape casting fluorinated YBC123

    Taylor, J.A.T.; Luke, D.M.; Whiteley, B.A.

    1991-01-01

    Tape casting the superconducting Ba-Y-Cu oxide was accomplished by several laboratories and show promise for being a versatile forming technique. The major problem is low current density, probably due to lack of grain alignment and grain boundary related weak links. The latter problem may be due to formation of carbonates and hydroxides during binder burnout. Preliminary work done at Alfred shows that a bimodal powder size distribution displays significant alignment after tape casting and that F treated powder is resistant to attack by steam at 100C. Such corrosion resistant powder cast as form tape should survive the binder burnout without the detrimental grain boundary phases that develop from reaction of the superconducting phase, steam and carbon dioxide. This paper presents the results of an investigation of tape casting fluorinated powder with a bimodal size distribution

  7. The CAST Time Projection Chamber

    Autiero, D.; Carmona, J.M.; Cebrian, S.; Chesi, E.; Davenport, M.; Delattre, M.; Di Lella, L.; Formenti, F.; Irastorza, I.G.; Gomez, H.; Hasinoff, M.; Lakic, B.; Luzon, G.; Morales, J.; Musa, L.; Ortiz, A.; Placci, A.; Rodriguez, A.; Ruz, J.; Villar, J.A.; Zioutas, K.

    2007-01-01

    One of the three X-ray detectors of the CAST experiment searching for solar axions is a Time Projection Chamber (TPC) with a multi-wire proportional counter (MWPC) as a readout structure. Its design has been optimized to provide high sensitivity to the detection of the low intensity X-ray signal expected in the CAST experiment. A low hardware threshold of 0.8 keV is safely set during normal data taking periods, and the overall efficiency for the detection of photons coming from conversion of solar axions is 62 %. Shielding has been installed around the detector, lowering the background level to 4.10 x 10^-5 counts/cm^2/s/keV between 1 and 10 keV. During phase I of the CAST experiment the TPC has provided robust and stable operation, thus contributing with a competitive result to the overall CAST limit on axion-photon coupling and mass.

  8. Niobium in gray cast iron

    Castello Branco, C.H.; Beckert, E.A.

    1984-03-01

    The potential for utilization of niobium in gray cast iron is appraised and reviewed. Experiments described in literature indicate that niobium provides structural refinement of the eutectic cells and also promotes pearlite formation. (Author) [pt

  9. Some Theoretical Considerations on Caste

    Madhusudan Subedi

    2014-05-01

    Full Text Available Caste as a system of social stratification was an encompassing system in the past. There was reciprocal system of exchange goods and services. With time, occupation and mode of generation of livelihood of various caste groups changed, and the traditional form of jajmani system fizzled out. This paper provides an account of changing perspectives of caste relations in social science writing and political discourse. The discourse of caste has been shifted from ritual hierarchy and social discrimination to an instrument to mobilize people for economic and political gain. DOI: http://dx.doi.org/10.3126/dsaj.v7i0.10437 Dhaulagiri Journal of Sociology and Anthropology Vol. 7, 2013; 51-86

  10. 14 CFR 23.621 - Casting factors.

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Casting factors. 23.621 Section 23.621... Casting factors. (a) General. The factors, tests, and inspections specified in paragraphs (b) through (d... structural castings except castings that are pressure tested as parts of hydraulic or other fluid systems and...

  11. Modelling of flow phenomena during DC casting

    Zuidema, J.

    2005-01-01

    Modelling of Flow Phenomena during DC Casting Jan Zuidema The production of aluminium ingots, by semi-continuous casting, is a complex process. DC Casting stands for direct chill casting. During this process liquid aluminium transforms to solid aluminium while cooling down. This is not an

  12. Digilanid C by die behandeling van hartlyers

    Snyman, Hendrik Willem

    1942-01-01

    In die voorafgaande word 'n literatuur studie oor die ontwikkeling en huidige stand van die chemie en farmakologie van die Digitalis purpurea en Digitalis lanata gegee, waarin spesiaal gelet word op die chemiese samestelling en farmakologiese aktiwiteit van die Digitalis lanata glikoside. Daarna

  13. HISTORIESE OORSIG VAN DIE ONTSTAAN EN ONTWIKKELING ...

    In 1933 belas Rykskanselier. Hitler vir. Goering, Minister van Lugvaart, in die geheim met die skepping van die Luftwaffe. Die basis in Rusland is gesluit en toekomstige vlieeniers is nou in die geheim na Italie waar hulle elke aspek van moderne oorlog- voering oefen en die Blitzkrieg-gedagte, deur op ondersteuning van 'n.

  14. EUNUG IN DIE ANTIEKE NABYE OOSTE

    rang. In Assiries beteken die woord “hoof-eunug”. Soos reeds vermeld (by 2), vorm die eunug 'n belangrike deel van die Assiriese burokrasie. Dokumente dui aan ... rang in die Babiloniese weermag, en so 'n amptenaar het saam met die rabsag ..... baie laat, in die inter-testamentêre periode, gebruik is vir 'n gekastreerde.

  15. Die betekenis van die konsep land in die slot van die boek Amos

    J.L. Helberg

    1999-08-01

    Full Text Available The meaning of the concept of land in the epilogue of the book of Amos During the exilic and post-exilic eras the concept of land underwent a shift of meaning: land also acquired the meaning of city (and temple. If the epilogue of Amos is regarded as exilic or post-exilic, as most scholars think, one can expect that city rather than land shall be emphasized in the epilogue. The opposite, however, is true. This article tries to ascertain whether the concept “land” has a different place, value or meaning in the epilogue of Amos than in the rest of the book and whether this assumption casts any light on the relation between the different parts. The conclusion arrived at implies that the term used for land in the epilogue has a broader meaning than the traditional one attached to it by Israel. The epilogue makes a breakthrough to a universal approach pictured in eschatological colours but rooted in history. A correction is made to a “Zion-theology” and emphasis is laid on the land of the promise which is linked with the (true covenantal relation with Yahweh implied in the terms “my people” and “your God”. Whether dated as pre-exilic, exilix or post-exilic, the epilogue is in harmony with the essence of the rest of the book.

  16. Optimizing the Gating System for Steel Castings

    Jan Jezierski

    2018-04-01

    Full Text Available The article presents the attempt to optimize a gating system to produce cast steel castings. It is based on John Campbell’s theory and presents the original results of computer modelling of typical and optimized gating systems for cast steel castings. The current state-of-the-art in cast steel casting foundry was compared with several proposals of optimization. The aim was to find a compromise between the best, theoretically proven gating system version, and a version that would be affordable in industrial conditions. The results show that it is possible to achieve a uniform and slow pouring process even for heavy castings to preserve their internal quality.

  17. Effect of dental technician disparities on the 3-dimensional accuracy of definitive casts.

    Emir, Faruk; Piskin, Bulent; Sipahi, Cumhur

    2017-03-01

    Studies that evaluated the effect of dental technician disparities on the accuracy of presectioned and postsectioned definitive casts are lacking. The purpose of this in vitro study was to evaluate the accuracy of presectioned and postsectioned definitive casts fabricated by different dental technicians by using a 3-dimensional computer-aided measurement method. An arch-shaped metal master model consisting of 5 abutments resembling prepared mandibular incisors, canines, and first molars and with a 6-degree total angle of convergence was designed and fabricated by computer-aided design and computer-aided manufacturing (CAD-CAM) technology. Complete arch impressions were made (N=110) from the master model, using polyvinyl siloxane (PVS) and delivered to 11 dental technicians. Each technician fabricated 10 definitive casts with dental stone, and the obtained casts were numbered. All casts were sectioned, and removable dies were obtained. The master model and the presectioned and postsectioned definitive casts were digitized with an extraoral scanner, and the virtual master model and virtual presectioned and postsectioned definitive casts were obtained. All definitive casts were compared with the master model by using computer-aided measurements, and the 3-dimensional accuracy of the definitive casts was determined with best fit alignment and represented in color-coded maps. Differences were analyzed using univariate analyses of variance, and the Tukey honest significant differences post hoc tests were used for multiple comparisons (α=.05). The accuracy of presectioned and postsectioned definitive casts was significantly affected by dental technician disparities (Ptechnician differences. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  18. Modelling and multi objective optimization of LM13 aluminium alloy squeeze cast process parameters using taguchi and genetic algorithm

    S. Vellingiri

    2018-01-01

    Full Text Available This present investigation deals with squeeze casting process in order to produce a component with good mechanical properties such as micro-hardness(VH, tensile strength(Rm, and density(ρ on LM13 by varying squeeze pressure(P, molten temperature(Tm and die temperature(Td. Taguchi experimental design L9 orthogonal array was used to determine the signal to noise ratio. The results specified that the squeeze pressure and die preheat temperature are the most influencing parameters for mechanical properties improvement. Genetic algorithm (GA has been applied to optimize the casting parameters that simultaneously maximize the responses.

  19. Die Transition zur pflegenden Tochter

    Dagmar Dräger

    2004-11-01

    Full Text Available Das Buch aus der Reihe „Studien zur Gesundheits- und Pflegewissenschaft“ beschreibt den theoretischen Hintergrund, das methodische Vorgehen und die Ergebnisse einer biografischen Untersuchung, die sich dem Übergang von der Tochter zur pflegenden Tochter widmete. Grundlage der Publikation ist die Dissertation (2002 der Autorin. Mit der Berücksichtigung biographischer und familiärer Hintergründe wird eine neue Perspektive in der Forschung zu pflegenden Angehörigen eingenommen.

  20. Maintaining Low Voiding Solder Die Attach for Power Die While Minimizing Die Tilt

    Hamm, Randy; Peterson, Kenneth A.

    2015-10-01

    This paper addresses work to minimize voiding and die tilt in solder attachment of a large power die, measuring 9.0 mm X 6.5 mm X 0.1 mm (0.354” x 0.256” x 0.004”), to a heat spreader. As demands for larger high power die continue, minimizing voiding and die tilt is of interest for improved die functionality, yield, manufacturability, and reliability. High-power die generate considerable heat, which is important to dissipate effectively through control of voiding under high thermal load areas of the die while maintaining a consistent bondline (minimizing die tilt). Voiding was measured using acoustic imaging and die tilt was measured using two different optical measurement systems. 80Au-20Sn solder reflow was achieved using a batch vacuum solder system with optimized fixturing. Minimizing die tilt proved to be the more difficult of the two product requirements to meet. Process development variables included tooling, weight and solder preform thickness.