Preparation of CaSO4:Dy by precipitation method to gamma radiation dosimetry

International Nuclear Information System (INIS)

Rivera, T.; Roman, J.; Azorin, J.; Sosa, R.; Guzman, J.; Serrano, A.K.; Garcia, M.; Alarcon, G.

2010-01-01

This paper presents the results of the preparation and characterization of dysprosium-doped calcium sulfate (CaSO 4 :Dy) phosphor, which was obtained by homogeneous precipitation from calcium acetate Ca(CH 3 COO - ) 2 . Structural and morphological characteristics were studied using a scanning electronic microscope (SEM). The structure of all compounds was determined by X-ray diffraction method too. Thermoluminescence (TL) emission properties of CaSO 4 :Dy under gamma radiation effects were studied. This phosphor powder presented a TL glow curve with two peaks (Tmax) centered at around of 180 and 300 deg. C, respectively. The TL response of CaSO 4 :Dy as a function of gamma absorbed dose was linear in a wide range. Both emission and excitation spectra were also obtained. Results showed that this new preparation method of CaSO 4 :Dy TL phosphor is less expensive, cleaner and safer than the conventional preparation method.

Environmental monitoring by CaSO4:Dy TL dosimeters

International Nuclear Information System (INIS)

Deme, S.; Szabo, P.P.

1975-12-01

The thermoluminescent dosimeters of high sensitivity are useful for monitoring the area near nuclear installations. CaSO 4 :Dy TL dosimeters have high sensitivity and low fading so that by means of them the dose from the background can be measured with an accuracy of 10-20%. An increase of 2 mR in the background can be observed and doses as high as 1000R can be registered with an accuracy of 5%. The measuring method and results are reported here. For two years these CaSO 4 :Dy dosimeters have been successfully used at the site of the Central Research Institute for Physics. (K.A.)

Thermal neutron detection by activation of CaSO4:Dy + KBr thermoluminescent phosphors

International Nuclear Information System (INIS)

Gordon, A.M.P.L.; Muccillo, R.

1979-01-01

Thermoluminescence (TL) studies to detect thermal neutrons were performed in cold-pressed CaSO 4 :0,1%Dy + KBr samples. The detection is based on the self-irradiation of the CaSO 4 :Dy TL phosphor by the Br isotopes activated by exposure to a mixed neutron-gamma field. (Author) [pt

Gamma ray induced sensitization in CaSO4:Dy and competing trap model

International Nuclear Information System (INIS)

Nagpal, J.S.; Kher, R.K.; Gangadharan, P.

1979-01-01

Gamma ray induced sensitization in CaSO 4 :Dy has been compared (by measurement of TL glow curves) for different temperatures during irradiation (25 0 , 120 0 and 250 0 C). Enhanced sensitization at elevated temperatures seems to support the competing trap model for supralinearity and sensitization in CaSO 4 :Dy. (author)

Thermoluminescence mechanisms in CaSO4:Dy single crystals

International Nuclear Information System (INIS)

Morgan, M.D.; Stoebe, T.G.

1986-01-01

ESR studies of gamma-irradiated CaSO 4 :Dy have shown, in addition to the usual intrinsic defects, four new paramagnetic centres. An analysis of the g values and the g tensors in conjunction with the anhydrite crystal structure indicate that these centres are related to sulphate ions. Two of these centres (denoted 1a and 3a) are proposed as holes trapped and shared between two adjacent sulphate ions, this structure being stabilised by a neighbouring Ca vacancy. Centre 3b is suggested as a hole associated with one sulphate ion, again stabilised by an adjacent Ca vacancy. Because of the two distinct crystallographic directions in the anhydrite structure, centre 3b was found to consist of two distinguishable defects with slightly differing decay temperatures. The fourth centre appears to be an electron trapping site with structure similar to centre 3b. Decay temperatures of these ESR defects are correlated with the observance of TL peaks in CaSO 4 :Dy. Thermoluminescence studies as a function of impurity content confirmed the presence of calcium vacancies, which are formed during crystal growth, and that they play an important role in the TL process. TL models are proposed to account for the observed properties of CaSO 4 :Dy. (author)

Phototransferred TL studies in CaSO4:Dy

International Nuclear Information System (INIS)

Nagpal, J.S.; Kathuria, V.K.; Gangadharan, P.

1980-01-01

PTTL studies in CaSO 4 :Dy have revealed two high temperature peaks at 500 and 570 0 C in γ-exposed phosphor. Employing 365 nm for phototransfer at elevated temperature 95 0 C, PTTL can serve a useful technique for re-estimation of the radiation exposure. (author)

Thermoluminescent characteristics of CaSO4:Dy+PTFE irradiated with high energy electron beams

International Nuclear Information System (INIS)

Alvarez, R.; Rivera, T.; Calderon, J. A.; Jimenez, Y.; Rodriguez, J.; Oviedo, O.; Azorin, J.

2011-10-01

In the present work thermoluminescent response of dysprosium doped calcium sulfate embedded in polytetrafluorethylene (CaSO 4 :Dy+PTFE) under high electron beam irradiations from linear accelerator for clinical applications was investigated. The irradiations were carried out using high electron beams (6 to 18 MeV) from a linear accelerator Varian, C linac 2300C/D, for clinical practice purpose. The electron irradiations were obtained by using the water solid in order to guarantee electronic equilibrium conditions. Field shaping for electron beams was obtained with electron cones. Glow curve and other thermoluminescent characteristics of CaSO 4 :Dy+PTFE were conducted under high electron beams irradiations. The thermoluminescent response of the pellets showed and intensity peak centered at around 235 C. Thermoluminescent response of CaSO 4 :Dy+PTFE as a function of high electron absorbed dose showed a linearity in a wide range. To obtain reproducibility characteristic, a set of pellets were exposed repeatedly for the same electron absorbed dose. The results obtained in this study can suggest the applicability of CaSO 4 :Dy+PTFE pellets for high electron beam dosimetry, provided fading is correctly accounted for. (Author)

Performance of CaSO4:Dy detectors

International Nuclear Information System (INIS)

Setti, M.C.; Silva, G.R.; Pela, C.A.; Bruco, J.L.; Borges, J.C.

2004-01-01

CaSO 4 :Dy detectors have been used in personal dosimetry. The MRA company recently entered into the market of these detectors. Searching to assure a product quality level that would satisfy its customs most expectancies, MRA programmed several tests to qualify and quantify these detectors main characteristics, before their definitive insertion in the market. Preliminary tests furnished a value of 29,5 ± 1,2 nC for homogeneity and a maximum dispersion of 3 % for linearity . (author)

Development of quality assurance procedures for thermoluminescent CaSO sub 4 :Dy-teflon skived tape dosemeter

Energy Technology Data Exchange (ETDEWEB)

Nagpal, J.S.; Popli, K.L.; Kher, R.K.; Varadharajan, G. (Bhabha Atomic Research Centre, Bombay (India). Div. of Radiological Protection)

1992-01-01

CaSO{sub 4}:Dy-Teflon TLD dosemeter material has been manufactured locally in a 0.4 mm thick continuous tape form. Fourteen batches have been examined for physical thickness, density, spectral transmission, diffuse optical density, beta transmission and TL output per unit area for evolving a procedure for quality assurance of the TLD element for large scale production. With the exception of two batches, the TL output per unit area of the tape for a number of batches lies within {+-}7% of that for a standard batch. (author).

Feasibility study on using three element TLD badge based on CaSO4:Dy as environmental dosimeter

International Nuclear Information System (INIS)

Choudhary, Sreeletha; BharathiLashmi, G.V.; Yasotha, E.; Devanathan, P.S.; Annalakshmi, O.; Mathiyarasu, R.

2018-01-01

A three element thermoluminescence badge based on CaSO 4 :Dy is used for personnel monitoring in India. The three discs of the badge is heated in sequential manner by hot nitrogen gas and from the amount of light emitted while heating, the doses are estimated. This badge was redesigned as a two element system and is used for environmental monitoring. Though the two element badge has some advantages, the software used for processing of TLDs in the semiautomatic reader has to be modified and separate badges has to be maintained for environmental dose measurements. In this work a feasibility study has been carried out to use the three element personnel monitoring badge itself for environmental monitoring also. This study was also carried out to understand the abnormal pattern of the glow curves observed in some field cards

Thermal behaviour of the thermoluminescent dosemeter CaSO4: Dy + NaCl

International Nuclear Information System (INIS)

Antonio Filho, J.

1988-01-01

Thermoluminescent materials are widely applied in radiation dosimetry. Nevertheless to obtain a good degree of reliability, it is necessary to subject the materials to an adequate thermal treatment, before and after irradiation, conveniently controlling temperature, heating time and cooling rate. It has been observed that the TLD CaSO 4 : Dy + NaCl loses 10% of its sensivity after each utilization cycle with the thermal treatment usually recomended. This fact establishes a severe limitation in works requiring a good measurement precision. Several alternative procedures, which overcome this limitation, have been studied. Two of the procedures yielded excellent results, with a coefficient of variation of 1 to 1.3%. One of them consist of two heating cycles at 300 0 C during 15 and three hours respectively, before irradiation, followed by a heating cycle at 100 0 C during 15 minutes, after irradiation. In a second procedure the material is heated at 300 0 C during three hours, pre-irradiation, followed by a heating cycle at 100 0 C. during 15 minutes, after irradiation. In all cases the heating cycle are followed by fast cooling periods. (author) [pt

Development of CaSO4:Dy based ring dosemeter for extremity monitoring of radiation workers in India

International Nuclear Information System (INIS)

Srivastava, Kshama; Meenal, P.; Bhagat, R.V.; Singh, R.; Kolambe, D.H.; Chougaonkar, M.P.; Sapra, B.K.

2014-01-01

Extremity dosemeters are required to be worn in cases where the dose to extremities is expected to be significantly greater than the dose to the whole body. In India, CaSO 4 :Dy based three element personnel monitoring TLD badge worn at chest and wrist level are used for whole body and extremity monitoring, respectively. Presently no official/legal finger dosemeter is available for extremity monitoring for radiation workers in the country. To cater to the long standing requirement of finger dosimeter, a new compact three-element Extremity Ring Badge Dosemeter (ERBD) has been developed for measurement of the equivalent doses received by the extremities of radiation workers in terms of operational quantity Hp(0.07). It was aimed to meet the performance requirement of IEC/ISO standards. This paper gives the design detail and result of experimental studies of ERB dosemeter

Application of photo transferred thermoluminescence in the ophthalmologic area by using CaSO4:Dy

International Nuclear Information System (INIS)

Grossi, Fabio H.; Campos, Leticia L.; Schor, Paulo; Melo Junior, Luis A.S. de

2002-01-01

The utilization of CaSO 4 :Dy pellets to laser radiation detection on the ophthalmologic area is being studied by IPEN together with UNIFESP, in order to obtain an adequate dosimeter to set the dose laser spread and received by the patients, professional of health and environmental. The method of phototranferred thermoluminescence (PTTL) using CaSO 4 :Dy pellets with 0,8 mm of thickness, introduced good sensibility to the excimer laser used on UNIFESP. The PTTL signal to the laser radiation shown reproducible and linear in a great range of absorbed energy (∼ 4.000 mJ) and gamma doses (5-100 Gy) and, points of measure with distances source laser-sample in order of 4,0 m presents good resolution of the PTTL signal. A method of monitoring the area in the surgery room was tried between the IPEN and UNIFESP. Using the CaSO 4 :Dy, the researchers have had a method cheaper and accessible to study the eventual risks of the ultraviolet radiation on the chromosomic breakage and in the development of malignancies tumors in professional of health exposed daily to the excimer laser used in corneans refractive surgeries. (author)

Hand book on the use of TLD badge based on CaSO4:Dy teflon TLD discs for individual monitoring

International Nuclear Information System (INIS)

Pradhan, A.S.; Adtani, M.M.; Varadharajan, G.; Bakshi, A.K.; Srivastava, Kshama; Bihari, R.R.

2002-10-01

Individual monitoring is one of the most important aspects of a radiation protection programme. In India, an official and centralized personnel monitoring service to radiation workers started in 1952. With the indigenous development of a TLD badge system in 1975 at Bhabha Atomic Research Centre, decentralization of monitoring service was initiated. At present, about 40,000 radiation workers are monitored using this system through twelve TLD units located in different parts of the country, including a private accredited laboratory. Regulatory and other inspecting bodies have often asked outstation TLD units to produce a duly approved document on the procedures being practiced for the assessment of personal doses. A need for such a document has also been felt to ensure the uniformity in processing of dosemeters, recording and reporting of doses by different TLD units and to provide guidelines regarding the infrastructure requirement. This document in the form of a handbook has been prepared to cater to the above needs. The handbook is expected to provide necessary guidelines not only to the newcomers/ forthcoming units and the existing laboratories but also to help the regulators, inspectors and assessors. (author)

Thermal neutrons thermoluminescence dosimetry using CaF2 + KBr e CaSO4: Dy + Br

International Nuclear Information System (INIS)

Leite, A.M.P.

1979-01-01

Cold-pressed samples of CaF 2 + KBr and CaSO 4 :Dy + KBr have been used in the thermal neutron detection by the thermoluminescence technique. The amount of 100 mg of the TL phosphor added to 80 mg of KBr showed to be the optimum mixture regarding sensitivity as well as the handling of the dosimeters. The detection is based on the self-irradiation of the phosphor by the Br isotopes activated by exposure to a neutron-gama field. The prompt dose and consequentely the gama contribution are erased by post-irradiation thermal annealing. A linear dependence has been found between the TL self-induced signal and the thermal neutron flux in the range 10 6 n.cm -2 .seg -1 -10 -12 n.cm -2 .seg -1 . The minimum detectable fluence has benn determined as 10 9 n.cm -2 and 10 6 n.cm -2 using pellets of CaF 2 + KBr and CaSO 4 :Dy + KBr, respectively. The main results suggest the use of CaSO 4 :Dy + KBr pellets and TL as a complementary technique for thermal neutron detection. (author) [pt

Photo-TL in CaSO4:Dy: high exposure dosimetry

International Nuclear Information System (INIS)

Caldas, L.V.E.; Mayhugh, M.R.

1974-01-01

CaSO 4 :Dy exposed to 10 3 to 10 8 R then annealed in the range 280 to 400 0 C displays little TL in the major dosimetry peak near 200 0 C. Subsequent illumination with 250 nm light reinduces the 200 0 C TL. This radiation-enabled photo-TL is roughly proportional to the square root of the enabling exposure at least to 10 8 R. (auth)

Calculated energy dependence of CaSO4:Dy TL phosphor and phosphor embedded Teflon for X and gamma rays

International Nuclear Information System (INIS)

Chang, J.-K.; Nam, Y.-M.; Kim, J.-L.; Chang, S.-Y.; Kim, B.-H.

2001-01-01

The energy dependence of a CaSO 4 :Dy TL phosphor for 21 monoenergetic photons of energy ranging from 0.01 to 3 MeV was calculated by using MCNP4A code. The calculation results show good agreement with those of other authors within ± 5% relative error. Calculations and experiments are also performed to determine the energy dependence of CaSO 4 : Dy phosphor with Dy concentrations from 0.01 to 1.5 mol %, and with the compositions of TL-Teflon from 10 to 90 wt %. The calculated energy responses show good agreement with the experiment results within ± 20% relative error except for a concentration lower than 0.1 mol % Dy and the low energy regions of M30 (Eave.=20 keV) and M60 (Eave.=34 keV). For the TL-Teflon mixture, the energy dependence shows an decreasing trend with the increase of Teflon concentration in MCNP calculation but shows no dependence for TL-Teflon mixture proportions in experiment. These differences are due to the non-homogeneous distribution of Dy concentration and the effect of large grain size in the phosphors. The energy dependence of the 30 wt/o CaSO 4 (0.1 mol%;Dy) and 70 wt/o Teflon that is placed behind the filters of plastic, aluminum, copper, tin and lead with a thickness from 0.1 to 2 mm were calculated, respectively

Improvement in the dosimetric CaSO4: Dy obtention method

International Nuclear Information System (INIS)

Campos, L.L.; Frutuoso, P.H.; Souto, V.J.

1989-08-01

With the purpose of saving up in the dosimetric CaSO 4 : Dy production, a new method was developed to obtain single crystals. In this method the nitrogen flux used to carry the acid vapour was substituted by compressed air. It was compared all dosimetric properties of the crystals. There is no alteration in the glow curve. The sensitivity is the same in both cases and the lower detection limit is 3.8 x 10 -8 C.Kg -1 (150 μR) [pt

The role of annealing: effect on CaSO4:Dy phosphor with manganese and sodium impurities

International Nuclear Information System (INIS)

Li, S.-H.; Hsu, P.-C.

1990-01-01

The effect of the annealing treatment on the CaSO 4 :Dy phosphor with Mn and Na impurities was studied at different annealing temperatures from 100 0 C to 800 0 C. Doping with or without impurity caused no difference in the properties for temperatures less than 400 0 C. An annealing temperature greater than 400 0 C brings a reduction in low temperature peak intensities of CaSO 4 :Dy with Na only. The high temperature peak intensities increase as the temperature increases from 400 0 C to 600 0 C. However, annealing at a temperature greater than 600 0 C brings a drastic reduction in high temperature peak intensities as well as TL output. (author)

Assessment of CaSO4:Dy and LiF:Mg,Ti thermoluminescent dosimeters performance in the dosimetry of clinical electron beams

International Nuclear Information System (INIS)

Nunes, Maira Goes

2008-01-01

The assessment of the performance of CaS0 4 :Dy thermoluminescent detectors produced by IPEN in the dosimetry of clinical electron beams aims to propose an alternative to the LiF:Mg,Ti commercial dosimeters (TLD-100) largely applied in radiation therapy. The two types of thermoluminescent dosimeters were characterised with the use of PMMA, RMI-457 type solid water and water phantoms in radiation fields of 4, 6, 9, 12 and 16 MeV electrons of nominal energies in which the dose-response curves were obtained and the surface and depth doses were determined. The thermoluminescent response dependency with the electron nominal energies and the applied phantom were studied. The CaS0 4 :Dy presented the same behaviour than the LiF:Mg,Ti in such a way that its application as an alternative to the TLD-100 pellets in the radiation therapy dosimetry of electron beams is viable and presents the significantly higher sensitivity to the electron radiation as its main advantage. (author)

Fast neutron dosimetry using CaSO4:Dy thermoluminescent dosimeters

International Nuclear Information System (INIS)

Azorin, N.G.; Salvi, C.R.; Rubio, J.L.; Gutierrez, C.A.

1980-01-01

The use of CaSO 4 :Dy phosphor powder in fast neutron dose measurements using the activation of sulphur from the 32 S(n,p) 32 P reaction is described. The thermoluminescence induced during the irradiation and that due to the decay of short-lived activation products, is erased by annealing the dosimeters after a post-irradiation time of 3 days. The self-induced thermoluminescence measured at different intervals of post-irradiation time, gives an estimation of the fast neutron dose to which the dosimeters were exposed

Measurement of thermal neutron fluence with CaSO4 thermoluminescent phosphors

International Nuclear Information System (INIS)

Liu Jinhua; Su Jingling; Wei Zemin

1984-01-01

During neutron irradiation, some TL phosphors were activated. After leaving the irradiation field the TL phosphor produced self-irradiation. The TL output of self-dose was only related to the original neutron fluence and independent of the γ-radiation. Several CaSO 4 TL phosphors were made. They were CaSO 4 :Dy, CaSO 4 :Dy-Teflon, CaSO 4 :Dy mixed with Dy 2 O 3 , CaSO 4 :Mn mixed with Dy 2 O 3 . The linearity, and lower detection limits of these TL phosphors were measured. The thermal neutron response of CaSO 4 :Mn mixed with Dy 2 O 3 was 64 R/(10 10 cm -2 ) and the lower detection limit was 1.3x10 5 cm -2

Production of thermoluminescent dosemeters based on MgB4O7: Dy and MgB4O7: Tm

International Nuclear Information System (INIS)

Souza, Luiza Freire de; Souza, Divanizia N.

2013-01-01

The thermoluminescent dosimetry (TL) is a well-established technique for the detection of ionizing radiation in hospitals, clinics, and industrial establishments where there is the need to quantify the radiation. For this practice is require the use phosphors which are sensitive to radiation. Some phosphors are already commonly used in this practice, for example, TLD-100 (LiF: Mg, Ti), CaSO 4 :Tm and CaSO 4 :Dy. A compound that was most recently introduced in dosimetry and has many advantageous features to detect neutrons, electrons and gamma is the magnesium tetraborate (MgB 4 O 7 ), but the undoped material is not good for dosimetry, since signal does not show satisfactory thermoluminescence. The present work presents the analysis of the compound MgB 4 O 7 when doped with rare earth elements, thulium (Tm) and dysprosium (Dy). The production of MgB 4 O 7 : Dy and MgB 4 O 7 : Tm occurred under acidic conditions. Following the process of crystal growth, several tests were made on phosphors produced to verify the quality of materials as TL dosimeter. Initially, was made the identification of the crystalline phases found in the material, using the technique of X-ray diffractometry, and then were evaluated and compared the TL emission curves of the crystals with two different types of dopants, to this, the samples were irradiated with different radiation sources: 137 Cs (0,66 MeV), 60 Co (1.25 MeV) and X-rays (0.41 MeV) and based on the results was evaluated the energy dependence of phosphors. Another characteristic analyzed, was the decay of TL signal for the material (fading). The results show that the material can be an excellent TL dosimeter when doped with rare earth elements Dy and Tm. (author)

Thermoluminescent response of CaSO4: Dy + PTFE to beta particles

International Nuclear Information System (INIS)

Aguirre C, A.; Azorin N, J.

2000-01-01

In this work the results of studying the thermoluminescent properties of CaSO 4 : Dy + PTFE are presented when it is irradiated with beta particles. The conclusion was the obtention of the Tl response curve in function of dose is that to desexcite the dosemeters at temperature 300 C during 30 minutes and after that were irradiated at different times in groups and to do the reading of dosemeter, it can be observed that a greater irradiation time major is the Tl response and this depends of the material has been used. (Author)

Evaluation of the substitution of PMMA plates by PLA 3D printed in TL response of CaSO_4:Dy

International Nuclear Information System (INIS)

Almeida, Shirlane Barbosa de; Valeriano, Caio Cesar Santos; Campos, Leticia Lucente

2016-01-01

The CaSO_4:Dy is a dosimetric material that is nationally produced, which presents high sensibility but a high energy dependence of its thermoluminescent (TL) response at the photoelectric effect region. This study aims to compare the TL response of the CaSO_4:Dy when irradiated, with different energies, at the presence of 3D printed plates of polylactic acid (PLA) and polymethylmethacrylate (PMMA). Results show that the PLA has a different attenuation of the radiation, when compared to PMMA, indicating that it should be taken into account the quality of the print used on PLA plates manufacture. (author)

CaSO4:Dy and/or Tm: study of its properties for dosimetry application

International Nuclear Information System (INIS)

Ferreira, M.M.

1979-01-01

In order obtain in practical and cheap solid state dosimeter with high sensitivity, a technique initially developed to cold press a mixture of suitable materials in their powder form sensitive to radiation. The material initially used was natural CaF 2 (fluorite) for this salt was extensively studied in radiation dosimetry since it shows a thermoluminescent (TL) effect after radiation. However, natural calcium fluorite shows two main disadvantages: its high senstivity to room light and the impossibility to control its impurity content due to its natural origin. Calcium sulphate was thus used as a good substitute of fluorite. Rare earths doped calcium sulphate shows a high TL sensitivity and is not disturbed by light. It is also easily obtained in the laboratory under controlled conditions so to get reproducible impurity content. The best dosimeters that can be produced with rare earth doped calcium sulphate are CaSO 4 :Dy and CaSO 4 :Tm. Calcium sulphate, simultaneously doped with Tm and Dy was produced and 100% increase was obtained in the TL sensitivity when compared with the individually are earth doped calcium sulphate. (Author) [pt

Development of sintered composites CaSO4 doped with Dy and Nd

International Nuclear Information System (INIS)

Chagas, M.A.P.; Parente, L.J.; Souza, D.N.

2007-01-01

The main of this work was the developing of sintered composites in order to use as thermoluminescent dosimeters using a simple route to preparation, employing high temperature. The composites were prepared with CaSO 4 .2H 2 O doped with Dy 2 O 3 and NdO 3 . Initially CaSO 4 .2H 2 O was dehydrated in oven at 100 deg C by 1h. After the addiction dopants and homogenization of compounds, PVA was incorporated to make easy to compaction of composites. The pellets with 6 mm of diameter and 1 mm thickness were sintered at 900 deg C and 1000 deg C by 6 h. The TL emission showed two peaks when the samples were irradiated with beta source (Sr 90 +Y 90 ). In all cases, the calibration curves presented responses proportional to absorbed dose. The results showed that this material have potential to be used in dosimetry. (author)

TL sensitivity of CaSO4:Dy phosphor powder - effect of grinding

International Nuclear Information System (INIS)

Shastry, S.S.; Kher, R.K.

1979-01-01

Grinding of polycrystalline CaSO 4 :Dy phosphor to powder form induces lattice defects. Changes in thermoluminescence (TL) sensitivity due to variation in trap density in the bulk and on the surface of phosphor grains are studied using gamma and UV radiations. TL sensitivity to gamma increases with grinding time due to the contribution from the new bulk traps which are generated by grinding. The surface traps degrade with increase in grinding time resulting in a decrease in UV sensitivity. Results on regeneration of the TL sensitivity due to annealing at different temperatures are also included. (Auth.)

Investigation of beta ray attenuation in CaSO4:Dy(Tm)-teflon rods

International Nuclear Information System (INIS)

Szabo, P.P.

1990-12-01

Ultrathin discs were prepared from CaSO 4 :Dy(Tm)-teflon rods by cutting them with a microtom. The effect of cutting was studied experimentally. It was found that the cutting does not affect the TL signal of the discs, so one will be able to irradiate the rod and cut it afterwards which means that this method can be applied in the dosimetry of boundaries or to establish the energy of beta radiation. Depth dose distribution measurements were carried out by irradiating the rods with beta sources. (K.A.) 5 refs.; 6 figs

TLD personnel monitoring dose estimation- extending the upper limit of the dose range

International Nuclear Information System (INIS)

Popli, K.L.; Sathian, Deepa; Divakaran, T.; Massand, O.P.

2001-01-01

TLD personnel monitoring was introduced in the year 1975 in India and at present nearly 41,000 radiation workers are being monitored by 13 monitoring laboratories all over India. The BARC- TLD being used for personnel monitoring is based on CaSO 4 :Dy embedded in PTFE and semi-automatic TL reader using hot N 2 Gas for heating the dosimeters. This reader has the range to measure γ dose from ten μSv to 3 μSv and x-ray dose form 1 μ Sv to 0.3 Sv due to the higher sensitivity of CaSO 4 : Dy to lower energy photons (20keV-50 keV) generated by diagnostic x-ray units. The x-ray radiation workers are at present nearly 35% of the total radiation workers monitored and this number is expected to grow as more and more number of x-ray workers are covered under this service. The upper limit of the x-ray dose range of the instrument is 0.3 Sv, whereas in the past one year it has been observed that at least 25% of the total overexposures reported in case of x-ray workers have recorded the dose more than 0.3 Sv. This paper presents the technique developed to extend the upper limit of the range from 0.3 Sv to 1 Sv for x-rays and 10 Sv for γ rays

Adequacy of annealing duration in reducing the background counts of personnel monitoring TLD cards - a study

International Nuclear Information System (INIS)

Srivastava, Kshama; Varadharajan, Geetha; Punekar, M.P.; Chougaokar, M.P.; Ayappan, P.

2010-01-01

In India, the personnel monitoring service of ∼ 70,000 radiation workers is being provided using indigenously developed TLD system comprising three CaSO 4 :Dy embedded Teflon discs. In order to remove TL and reset the distribution of defects/trapping centres, all TLD cards are subjected to an annealing treatment at elevated temperature prior to their next use. As per the standardized protocol annealing is carried out in a hot air circulating oven at 230 deg C for 4 hr, which is sufficient to reset the TL dosemeters for dose levels upto 100 mSv. In order to verify the appropriateness of annealing procedures adopted by the Laboratory, a detailed study was conducted using four sets of cards namely A, B, C and D series, exposed to various dose levels

Dosimetric intercomparison in Cobalt 60 unities using TLD-100 crystals and CaSO{sub 4}: Dy + Ptfe; Intercomparacion dosimetrica en unidades de cobalto 60 usando cristales de TLD-100 y CaSO{sub 4}: Dy + PTFE

Energy Technology Data Exchange (ETDEWEB)

Gaona, E. [Universidad Autonoma Metropolitana Xochimilco, Mexico D.F. (Mexico); Azorin N, J. [Universidad Autonoma Metropolitana Iztapalapa, Mexico D.F. (Mexico); Perez P, M.A. [Instituto Nacional de Cancerologia, Mexico D.F. (Mexico); Castillo H, M. [Centro Medico Nacional 20 de Noviembre, ISSSTE, Mexico D.F. (Mexico); Flores F, F. [Unidad de Oncologia, Centro Medico Nacional, IMSS, Mexico D.F. (Mexico); Guzman R, L.V. [Unidad de Oncologia, Hospital General de Mexico, Mexico D.F. (Mexico)

1999-07-01

The purpose of this work is to design and construct a phantom in basis of thermoplastic polymer of methyl methacrylate that is reutilizable and which allows to do an analysis of the absorbed doses in thermoluminescent crystals (Tl) exposed to cobalt 60 to establish the dosimetric intercomparison in cobalt units which allows to do the follow-up of the Quality assurance programs, standardization of calibration procedures, dosimetry and TLD post intercomparison in radiotherapy. This work allows also prove new thermoluminescent materials of national manufacture developed by Juan Azorin and collaborators as the CaSO{sub 4}: Dy + Ptfe. This is a first study which is realized in Mexico with the system crystal-phantom for aims to intercomparison in cobalt 60 units. In this work participate eight unities of cobalt 60 of different trades belonging at four radiotherapy centers. The results of the dose intercomparison of the eight unities of cobalt 60 were in the range 0.95-1.13, taking in account that the values between 0.95 and 1.05 were considered acceptable in terms of the requirements by the standing legislation. (Author)

Development of thin dosemeters of CaSO4: Dy for beta radiation detection

International Nuclear Information System (INIS)

Campos, L.L.

1987-01-01

Thin pellets of CaSO: Dy (0,20mm) were produced and tested in beta radiation fields. The Thermolumiscent (TL) characteristics studied were sensitivity, reproducibility, lower detection limit, linearity of TL response with absorved dose energy dependence. The results show the usefulness of this thin pellets in beta radiation detection. (Author) [pt

Characteristics Of Dosimeter TL CaSO4:Dy Glass Capillaries For Environmental Radiation Dose Monitoring

International Nuclear Information System (INIS)

Sofyan Hasnel; Yulianti, Helfi; Ramain, Abubakar; Kusumawati, Dyah D.; Suyati

2000-01-01

research on the characteristic of dosimeter TL CaSO 4 : Dy glass capillaries for environmental dose radiation have been carried out. The results obtained are uniform response and reproducibility during three cycles consumption with average percentage standard deviation of 7.31 % and 5.45%. The response dose is linear and has a minimum detectable dose of 0.01 mGy, sunshine effect with non-penetrating light capsule of 4.65%, humidity effects is not significant by using non-penetrating light capsule. Radiation dose information during 30 days are fading 25%

Difficulty in estimation of dose for the abnormal patterns of the TLD disc readings - need investigation and improvement in work practices

International Nuclear Information System (INIS)

Madhumita, B.; Ande, C.D.; Sneha, C.; Bakshi, A.K.; Datta, D.

2018-01-01

TLD badge based on CaSO 4 :Dy detector used for external radiation monitoring of occupational workers of radiation facilities in India plays a vital role in radiation protection program. Energy and type of radiation in the work-field can be well identified from the dose evaluation algorithm. Algorithm developed earlier use the set of disc ratio from the three disc readings of the TLD badge to arrive at the dose and the type of radiation. Algorithm fails to estimate the dose for the abnormal patterns. The paper discusses the root cause of the abnormal patterns and investigation followed to arrive the estimation of dose

Pattern check of TLD disc readings - an important tool to identify abnormal conditions in workplace

International Nuclear Information System (INIS)

Pradhan, S.M.; Sneha, C.; Bhattacharya, M.; Sahai, M.K.; Pradeep, Ratna; Datta, D.; Bhatnagar, Amit

2016-01-01

Personnel monitoring for external radiation using CaSO 4 :Dy based TLD badge is well established in Indian radiation protection program. TLD badge enables evaluation of occupational dose based on the pattern and values of the three disc readings. Different patterns of disc readings are obtained depending on the type and energy of radiation in the workplace. Pattern not conforming to the radiation in the workplace also called as improper pattern can be a useful tool for investigation of any deviation / abnormality in workplace or monitoring practices. The paper presents different examples of improper pattern observed in monitoring that has helped to find out the deviations in the workplace or monitoring practices. Results of the experiments conducted to simulate some of the observed pattern are also presented in the paper

Thermoluminescent dosimeters for low dose X-ray measurements

International Nuclear Information System (INIS)

Del Sol Fernández, S.; García-Salcedo, R.; Sánchez-Guzmán, D.; Ramírez-Rodríguez, G.; Gaona, E.; León-Alfaro, M.A. de; Rivera-Montalvo, T.

2016-01-01

The response of TLD-100, CaSO_4:Dy and LiF:Mg,Cu,P for a range of X-ray low dose was measured. For calibration, the TLDs were arranged at the center of the X-ray field. The dose output of the X-ray machine was determined using an ACCU-Gold. All dosimeters were exposed at the available air kerma values of 14.69 mGy within a field 10×10 cm"2 at 80 cm of SSD. Results of LiF:Mg,Cu,P X-ray irradiated showed 4.8 times higher sensitivity than TLD-100. Meanwhile, TL response of CaSO_4:Dy exposed at the same dose was 5.6 time higher than TLD-100. Experimental results show for low dose X-ray measurements a better linearity for LiF:Mg,Cu,P compared with that of TLD-100. CaSO_4:Dy showed a linearity from 0.1 to 60 mGy - Highlights: • Low dose X-ray doses for personal dosimetry were measured. • Radiation dose (µGy ) for environmental dosimetry were determined. • Scattering radiation dose were measured by TLDs. • Linearity of pair TLD system was successful in the range of microgray. • Pair TLDs composed by CaSO_4:Dy and by LiF:Mg,Cu,P. is suggested for clinical dosimetry.

Effect of temperature during UV and gamma irradiations of TL phosphor CaSO4:Dy

International Nuclear Information System (INIS)

Nagpal, J.S.; Pendurkar, H.K.

1979-01-01

Temperature is an important parameter in thermoluminescence studies. Irradiation at enhanced temperatures reduces the γ response of TL phosphor CaSO 4 :Dy. However, in the presence of fluorescent lights, the γ response of the phosphor is enhanced by approximately 20% for temperatures around 60-100 0 C. If the phosphor temperature during UV exposure is kept high, the integrated TL output continues to increase until it reaches 18 times at 160 0 C as compared to that produced by UV exposure at room temperature. (Auth.)

Optimization of the obtaining method of CaSO4: Dy + Ptfe dosimeters

International Nuclear Information System (INIS)

Galicia A, J.; Rioja Ch, J.; Torijano C, E.; Azorin N, J.

2012-10-01

This work contain the obtained results of studying the response when irradiating to different dose of X-rays, dosimeters of CaSO 4 : Dy + Ptfe using different lapses of time in their preparation (a lot of selected dosimeters of an elaboration process of 3 days and another of an elaboration process of 2 hours). For the elaboration of the powdered material, the evaporation method was used; the irradiation were carried out in a lineal accelerator Elekta Synergy property of the National Medical Center, 20 de November. The similarities and differences are shown among the two dosimeters lots together with an analysis of the shine curves and of calibration selecting those that presented a better behaviour and a more rea liable response. (Author)

CaSO4: Dy + Teflon dosimetric pellets for X, beta and gamma radiation detection

International Nuclear Information System (INIS)

Campos, L.L.; Lima, M.F.

1987-08-01

CaSO 4 : Dy + TEFLON dosimetric pellets with high sensitivity and low cost for X, beta and gamma radiation monitoring were studied and developed by the Dosimetric Material Production Laboratory of the Radiological Protection Departament and are disposable for sale. The thickness of the pellets are suitable for X, beta and gamma radiation measurements. The dosimetric properties of these pellets were determined and presented in this work. The results show the usefulness of 0,20mm thick pellets for beta radiation monitoring and 0,80mm thick pellets for x and gamma radiation detection. (Author) [pt

Dosimetric characteristics and radiation monitoring with CaSO4(Dy):NaCl pellets

International Nuclear Information System (INIS)

Kathuria, S.P.; Campos, L.L.; Gordon, A.M.P.L.

1981-06-01

CaSO 4 (Dy):NaCl Tl dosimeters, in the form of pellets, are used in the field for a period of one month. Before using these pellets for environmental and personnel radiation monitoring some of the important dosimetric characteristics like fading reusability and effect of ambient light are investigated and described. The pellets are used with plastic and lead filters for personnel and environmental radiation monitoring and the results obtained with the lead filters are in good agreement with those of the energy independent LiF dosimeters. A new combination of plastic, aluminium and lead filters is suggested for dose measurements in a mixed field of X, gamma and beta radiations. (Author) [pt

Emission spectra of phosphor MgSO4 doped with Dy and Mn

International Nuclear Information System (INIS)

Zhang Chunxiang; Chen Lixin; Tang Qiang; Luo Daling; Qiu Zhiren

2001-01-01

Emission spectra of phosphor MgSO 4 doped with Dy and Dy/Mn were measured with an optical multichannel analyzer and a linear heating system whose temperature was controlled by a microcomputer. The emission spectrum bands at 480 nm and 580 nm of phosphor MgSO 4 doped with Dy were observed in the three dimensional (3D) glow curves. Compared with the 3D spectrum of CaSO 4 :Dy and the spectrum bands of MgSO 4 :Dy shows the same wavelengths which resulted from the quantum transitions among the energy levels of Dy 3 '+ ions. The intensities of the glow peaks in both spectrum bands (480 nm and 580 nm) of phosphor MgSO 4 doped with Dy/Mn were dramatically reduced except the 380 degree C glow peak

Environmental monitoring with a portable TLD system

Energy Technology Data Exchange (ETDEWEB)

Szabo, P P; Feher, I; Deme, S; Szabo, B; Vagvoelgyi, J; German, E [Hungarian Academy of Sciences, Budapest. Central Research Inst. for Physics

1984-01-01

Two types of TLD systems are used for environmental dose monitoring. One is based on an NHZ-203 laboratory TLD reader and CaSO/sub 4/:Dy powder. The other is based on CaSO/sub 4/:Tm bulbs and a small, portable TLD reader built into a cross-country car and operated by means of the car battery. The laboratory TLD system has been used for many years for environmental monitoring and it has been tested and proved satisfactory at international intercomparisons for environmental dosemeters. The new portable TLD system has the advantage of being able to establish the dose in a few minutes at the environmental station. The transport dose is omitted as the TLDs are evaluated at the field site. The evaluation of a bulb needs only a few minutes and the measured dose value can be reported back by radio - an important aspect during an emergency situation.

Optimizing a method to obtain CaSO4 activated with Dy for use in thermoluminescent dosimetry

International Nuclear Information System (INIS)

Gonzalez M, G.

1981-01-01

Results obtained from experiments in optimizing the variables in the preparation of CaSO 4 activated with dysprosium, as phosphors to be used as low dose TL dosemeters for routine radiological protection are presented. The technique used combined those of T. Yamashita and of K. Becker. Heating 8.6 gm of CaSO 4 .H 2 O with 0.1 mol % of Dy 2 O 3 in 115 ml of concentrated H 2 SO 4 to 285 0 C to completely evaporate the acid and placing the obtained crystals in a 600 0 C oven for one hour gave a TL dosimeter with a sensitivity sufficient to measure 5 mR of 60 Co gamma radiation and show a lineal response with this radiation in a 5 mR-5x10 4 R interval. Fading, which appeared in the phosphor only after three weeks, was in the fourth week 4.0% and in the eighth week 6.2% with a σ=+-2.1%. The quality of the phosphor obtained and its ease of reproducibility deserves note. (author)

Preparation and structural characterization of the thermoluminescent material CaSO4: Dy

International Nuclear Information System (INIS)

Sanchez R, A.; Azorin, J.; Gonzalez M, P.R.; Rivera, T.

2005-01-01

The grade of crystallinity of a material is important so that the one is presented the thermoluminescence phenomenon; for what is necessary to study those structural characteristic of a TL material and to correlate them with its TL response when being irradiated with ionizing radiation. The calcium sulfate activated with Dysprosium (CaSO 4 : Dy) it is a material that has demonstrated its efficiency in the dosimetry of the ionizing radiation for the thermoluminescence method. In this work the structural characterization of this prepared material for the recrystallization method by means of the evaporation of the solvent and their relationship with their TL response is presented. The results showed that the best material to be used in thermoluminescent dosimetry presents a crystalline structure in orthorhombic phase and a particle size in the interval of 80 μm to 200 μm. (Author)

Effect of the temperature in the sensitivity of CaSO4: Dy

International Nuclear Information System (INIS)

Gonzalez, P.R.; Alcantara, B.C.; Azorin, J.; Furetta, C.

2003-01-01

Sensitivity of a Tl material is one of the most important properties for dosimetry. This property is optimized by means of various processes such as the incorporation of different dopants into the matrix material, the application of certain doses of ionizing radiation and carefully controlled thermal treatments among others. Results obtained of studying the sensitivity of diverse preparations of CaSO 4 : Dy submitted different thermal treatments are presented. The material, which presented the highest sensitivity, was that one it was heated to 800 C during one hour. When the temperature was raised over this value it was observed that sensitivity drops again. In other hand, as the heating rate in lowing down, during the readout, the height of the glow curve decreases proportionally. The temperature of the maximum of the main peak also decreases. (Author)

Measurement of the dose by dispersed radiation in a lineal accelerator using thermoluminescent dosimeters of CaSO4:Dy

International Nuclear Information System (INIS)

Chavez C, N.; Torijano, E.; Azorin, J.; Herrera, A.

2014-08-01

The thermoluminescence (Tl) is based on the principle of the luminescent in a material when is heated below their incandescence temperature. Is a technique very used in dosimetry that is based on the property that have most of the crystalline materials regarding the storage of the energy that they absorb when are exposed to the ionizing radiations. When this material has been irradiated previously, the radioactive energy that contains is liberated in form of light. In general, the principles that govern the thermoluminescence are in essence the same of those responsible for all the luminescent processes and, this way, the thermoluminescence is one of the processes that are part of the luminescence phenomenon. For this work, the dispersed radiation was measured in the therapy area of the lineal accelerator of medical use type Elekta, using thermoluminescent dosimeters of CaSO 4 :Dy + Ptfe developed and elaborated in the Universidad Autonoma Metropolitana, Unidad Iztapalapa. With the dosimeters already characterized and calibrated, we proceeded to measure the dispersed radiation being a patient in treatment. The results showed values for the dispersed radiation the order of a third of the dose received by the patient on the treatment table at 30 cm of the direct beam and the order of a hundredth in the control area (4 m of the direct beam, approximately). The conclusion is that the thermoluminescent dosimeters of CaSO 4 : Dy + Ptfe are appropriate to measure dispersed radiation dose in radiotherapy. (author)

Development and evaluation of a new baDge/filter for thermoluminescent monitoring with CaSO4: Dy/PTFE

International Nuclear Information System (INIS)

Campos, Vicente de Paula

2005-01-01

Calcium Sulfate (CaSO 4 :Dy) phosphor Thermoluminescent Dosimeter (TLD) has been used by the Instituto de Pesquisas Energeticas e Nucleares (IPEN), SP, Brazil since 70's and 80's, due to important work of its researchers and collaborators. This phosphor advantages, beside the fact that it is produced by IPEN itself, begin to be more required and its disadvantages have became more apparent, in a global market more and more competitive. This phosphors was used primarily in environmental and area monitoring at IPEN facilities and in a few external institutions, once it presents more sensibility than other phosphors, like LiF:Mg. Its mainly disadvantage is a strong energetic dependence response to ionizing radiation, which must be corrected for its application in every radiation field. This phosphor has been used inside a badge which is an adaptation from photographic film badges used in the past. This badge permits a reasonable correction in the energetic dependence, only for orthogonal beam incidence. With the objective of improve the performance and reduce the energetic dependence on any incidence angle, reducing the dose measurement uncertainty too, this work presents a study on a new badge, with a new filter geometry, and its performance was compared to the actual dosimeter in use, with significant improve on results. Gamma irradiations of 60 Co and x-rays of 25,1; 33; 37,3 and 82,1 keV, on incidence angles of 0 deg, 30 deg, 45 deg and 90 deg were done at facility conditions of IPEN. Semi-empirical computational simulation using finite differences in three dimensions were done. The results pointed out the best filter thickness and width for initiate the prototype production, in order to optimize the correction on energetic dependence on irradiation of photons of 33, 48, 118 and 1250 keV energies under many incidence angles. (author)

Photoluminescence and absorption spectra of various common TL phosphors - interpretation of TL mechanisms

International Nuclear Information System (INIS)

Nagpal, J.S.

1980-01-01

Photoluminescence and absorption spectra of TL phosphors TLD-100, CaF 2 :Dy, CaSO 4 :Dy(0.05%wt), CaSO 4 :Tm(0.05%wt) and Mg 2 SiO 4 :Tb have been measured. The absorption spectra are typical of RE 2+ in rare earth doped irradiated phosphors. On heating RE 2+ yields RE 3+ and emission from the excited states of RE 3+ is observed. (author)

Study of LiF:Mg,Ti and CaSO4:Dy dosimeters TL response to electron beams of 6 MeV applied to radiotherapy using PMMA and solid water phantoms

International Nuclear Information System (INIS)

Bravim, A.; Sakuraba, R.K.; Cruz, J.C.; Campos, L.L.

2011-01-01

The performance of CaSO 4 :Dy and LiF:Mg,Ti dosimeters to electron beams applied to radiotherapy was investigated. The TL response of these dosimeters was studied for 6 MeV electron beams using PMMA and Solid Water (SW) phantoms. The dosimeters were previously separated in groups according to their TL individual sensitivities to 60 Co gamma-radiation in air under electronic equilibrium conditions. After that, they were irradiated with 6 MeV electron doses of 0.1, 0.5, 1, 5 and 10 Gy using a linear accelerator Clinac 2100C Varian of Hospital Israelita Albert Einstein – HIAE. The electron beam irradiations were performed using a 10 × 10 cm 2 field size, 100 cm source-phantom surface distance and the dosimeters were positioned at the depth of maximum dose (1.2 cm). The TL readings were carried out between 24 and 32 h after irradiation using a Harshaw 3500 TL reader. The TL dose–response of both type of dosimeters and phantoms presented linear behavior on the electron dose range from 0.1 to 5 Gy CaSO 4 :Dy dosimeter is 21 times more sensitive than LiF:Mg,Ti, dosimeter commonly used in clinical dosimetry. The obtained results indicate that the performance of CaSO 4 :Dy dosimeters is similar to LiF:Mg,Ti dosimeters and this material can be an alternative dosimetric material to be used to clinical electron beams dosimetry.

Self-dose and fading of CaSO4(Dy/Tm) and CaF2 (natural) TL phosphors in environmental radiation monitoring

International Nuclear Information System (INIS)

Nambi, K.S.V.

1982-01-01

A 'shielded storage experiment' for estimating both the 'self-dose' and 'fading' of TL phosphors under conditions akin to those faced in environmental monitoring applications is described. Using this method, self-dose rates of 0.32 +- 0.10(sigma) μ rad h -1 and 1.16 +- 0.02(sigma) μ rad h -1 have been obtained for CaF 2 (natural) and CaSO 4 (Dy) phosphors; the thermal decay constants at 25 0 C for these phosphors turn out to be 27 X 10 -6 h -6 ad 12 X 10 -6 h -1 , respectively. Estimation of the self-doses from radioactivity measurements of the phosphors concerned is also presented and the differences explained. A very high self-dose rate of 5.6 μ rad h -1 was estimated by the latter method for a sample of CaSO 4 (Tm) phosphor. (orig.)

Assessment of CaSO{sub 4}:Dy and LiF:Mg,Ti thermoluminescent dosimeters performance in the dosimetry of clinical electron beams; Avaliacao do desempenho dos detectores termoluminesncetes de CaSO{sub 4}:Dy e LiF:Mg,Ti na dosimetria de feixes clinicos de eletrons

Energy Technology Data Exchange (ETDEWEB)

Nunes, Maira Goes

2008-07-01

The assessment of the performance of CaS0{sub 4}:Dy thermoluminescent detectors produced by IPEN in the dosimetry of clinical electron beams aims to propose an alternative to the LiF:Mg,Ti commercial dosimeters (TLD-100) largely applied in radiation therapy. The two types of thermoluminescent dosimeters were characterised with the use of PMMA, RMI-457 type solid water and water phantoms in radiation fields of 4, 6, 9, 12 and 16 MeV electrons of nominal energies in which the dose-response curves were obtained and the surface and depth doses were determined. The thermoluminescent response dependency with the electron nominal energies and the applied phantom were studied. The CaS0{sub 4}:Dy presented the same behaviour than the LiF:Mg,Ti in such a way that its application as an alternative to the TLD-100 pellets in the radiation therapy dosimetry of electron beams is viable and presents the significantly higher sensitivity to the electron radiation as its main advantage. (author)

Simultaneos determination of absorbed doses due to beta and gamma radiations with CaSO4: Dy produced at Ipen

International Nuclear Information System (INIS)

Campos, L.L.; Rosa, L.A.R. da.

1988-07-01

Due to the Goiania radiological accident, it was necessary to develop urgently a dosimeter in order to evaluate, simultaneously, beta and gamma absorbed doses, due to 137 Cs radiations. Therefore, the Dosimetric Material Production Laboratory of IPEN developed a simple, practical, light and low cost badge using small thickness (0,20mm) thermoluminescent CaSO 4 : Dy pellets produced by the same laboratory. This pellets are adequate for beta radiation detection. These dosimeters were worn by some IPEN technicians who worked in Goiania city, and were used to evaluate the external and internal contaminations presented by the accident victims interned at the Hospital Naval Marcilio Dias. (author) [pt

Determination of exposure rates from natural background radiation in Khartoum using LiF:Mg,Cu,P (GR-200) and CaSo4: Mn TLD chips

International Nuclear Information System (INIS)

Suliman, I.I.; Khangi, F.A.; Shaddad, I.A.; Suliman, I.A.; El Amin, O.I.

2002-01-01

The exposure rates from natural background radiation - including terrestrial gamma radiation and the ionizing component of cosmic rays - were measured for the first time in the city of khartoum using two types of TLD materials: LiF:Mg,Cu,P (GR-200) and CaSo 4 :Mn TLD chips. Measurements were performed at two sites simultaneously, one site was selected on land in the vicinity of the Sudan Atomic Energy Commission, for the purposes of the measurement of the total exposure rate outdoors, while the other site was located on a buoy anchored in the Blue Nile, and was selected to measure the exposure rate due to the ionizing component of cosmic rays. The investigations were conducted for periods of between 5 and 28 days. Calibration was performed on a selected number of dosimeters to determine the exposure rates at each site. The exposure rates from the ionizing component of cosmic rays in Khartoum were found to be respectively 33 nGy.h -1 and 30 nGy.h -1 , in the measurements performed within the scope of this work using GR-200 and CaSo 4 :Mn dosimeters, while the total values for exposure on land were found to be 45 nGy.h -1 and 42 nGy.h -1 respectively. These values compare reasonably well with other national averages reported in the UNSCEAR publication. The comparison of the results for the two dosimetric materials demonstrates both the sensitivity and suitability of GR-200 for the purposes of environmental monitoring (orig.)

Measurement of annual dose on porcelain using surface TLD method

International Nuclear Information System (INIS)

Xia Junding; Wang Weida; Leung, P.L.

2001-01-01

In order to improve accuracy of TL authentication test for porcelain, a method of measurement of annual dose using ultrathin (CaSO 4 :Tm) dosage layer on porcelain was studied. The TLD was placed on the part of porcelain without glaze. A comparison of measurement of annual dose for surface TLD, inside TLD and alpha counting on porcelain was made. The results show that this technique is suitable for measuring annual dose and improving accuracy of TL authentication test for both porcelain and pottery

Photoluminescence and thermoluminescence characterization of Eu3+- and Dy3+ -activated Ca3(PO4)2 phosphor

International Nuclear Information System (INIS)

Nagpure, I.M.; Saha, Subhajit; Dhoble, S.J.

2009-01-01

Rare-earth-doped polycrystalline Ca 3 (PO 4 ) 2 :Eu, Ca 3 (PO 4 ) 2 :Dy and Ca 3 (PO 4 ) 2 :Eu,Dy phosphors prepared by a modified solid-state synthesis has been studied for its X-ray diffraction, thermoluminescence (TL) and photoluminescence (PL) characteristics. The PL emission spectra of the phosphor suggest the presence of Eu 3+ ion in Ca 3 (PO 4 ) 2 :Eu and Dy 3+ ion in Ca 3 (PO 4 ) 2 :Dy lattice sites. The TL glow curve of the Ca 3 (PO 4 ) 2 :Eu compounds has a simple structure with a prominent peak at 228 deg. C, while Ca 3 (PO 4 ) 2 :Dy peaking at 146 and 230 deg. C. TL sensitivity of phosphors are compared with CaSO 4 : Dy and found 1.52 and 1.20 times less in Ca 3 (PO 4 ) 2 :Eu and Ca 3 (PO 4 ) 2 :Dy phosphors, respectively. The Ca 3 (PO 4 ) 2 :Eu,Dy phosphors shows switching behavior under two different excitation wavelengths and enhancement in PL intensity of Dy 3+ ions were reported. The paper discusses the photoluminescence and thermoluminescence behavior of Eu 3+ and Dy 3+ ion in Ca 3 (PO 4 ) 2 hosts, it may be applicable to solid-state lighting as well as thermoluminescence dosimetry applications.

The effect of ultraviolet and visible radiation on the readout obtained from γ-irradiated and unirradiated CaSO4:Dy in teflon discs

International Nuclear Information System (INIS)

Bartnik, D.L.; Calvert, R.L.; Young, J.G.

1982-07-01

The effect of ultraviolet and visible radiation on the readout obtained from the main dosimetry peak of CaSO 4 :Dy in teflon discs is explained by the net result of three separate factors, namely (i) an inherent response, (ii) a phototransfer and (iii) an optical bleaching. Their dependence on wavelength, irradiance and radiant exposure has been studied using a fluorescent light enclosed in a perspex diffuser and a 200W mercury-xenon lamp in conjunction with narrow bandpass filters to isolate specific wavelengths

TLD territorial network in the Czech Republic

Energy Technology Data Exchange (ETDEWEB)

Kroutilikova, D. [National Radiation Protection Institute, Prague (Czech Republic)

1996-12-31

At present, there are 236 measuring points practically homogeneously distributed on the territory of the Czech Republic. 98 measuring points are distributed as local TLD-networks in the surroundings of Czech two nuclear power plants. Both of the TLD-networks are operated by the National Radiation Protection Institute in Prague. The dosimeters hitherto used are the CaSO{sub 4}:Dy-teflon detectors placed in TL-badges and shielded on both sides by energy compensation filters composed of lead and tin. Recently, a new modernization of the measuring system, type of dosimeter and methods of evaluation is under way. From 1996 the Czech Radiation Monitoring Network will be used the TLD system HARSHAW 4000, along with the type 8807 ENVIRONMENTAL DOSIMETER. The dosimeter is composed of four TL-elements - two LiF and two CaF{sub 2}, placed in a plastic badge. In addition, the CaF{sub 2} elements are shielded on both sides by energy compensation filters composed of tantalum and lead. Before the routine use of the new system a testing of the dosimeters was made. The following text summarizes the obtained results (J.K.). 4 tabs.

Utilization of thermoluminescent dosemeters for determination of exposure or absorbed dose in a radiation gamma or X radiation field with unknown spectral distribution

International Nuclear Information System (INIS)

Rosa, L.A.R. da.

1981-06-01

Having in view the choice of the best pair of dosemeters to be used in the 'Tandem' method, the main response characteristics of LiF:Mg, Ti, Li 2 B 4 O 7 :Mn, CaSO 4 Dy, CaF 2 :Mn and CaF 2 :Dy thermoluminescent dosemeters and also some critical parameters in their calibration and evaluation processes were studied. Three different physical forms of TLD's were investigated: hot pressed chips, disc teflon dosemeters and glass mini TLD's. Their calibration factors were obtained for the energy of Cobalt-60 gamma rays. Their energy dependences normalized to 60 Co radiation were determined using spectral width as parameter. 'Tandens' formed by all TLD's evaluated were compaired. (E.G.) [pt

Assessment of dose using TLD during activity handling at RPhL, BRIT

International Nuclear Information System (INIS)

Choughule, Nitin V.; Bairwa, S.M.; Murali, S.; Rakesh, R.B.; Madhumita, B.; Adtani, M.M.; Mehra, Kiran; Padmanabhan, D.; Borkute, S.D.; Pal, N.; Sachdev, S.S.

2012-01-01

Radiopharmaceutical Lab (RPhL), BRIT undertakes production, supply of radiopharmaceuticals. At RPhL short lived isotopes 131 I, 99 Mo, 99m Tc, 125 I, 153 Sm, 32 P and 51 Cr, are handled with total activity handled per week ranging from MBq to TBq (mCiCi). Radiological survey provides idea on radiation level helps to ensure safe working condition. In order to improve the working condition and to estimate the integrated dose over a period of week with uniform pattern of activity handling in the period, a study was carried out using TLD badges. Specifically prepared TLD badges containing CaSO 4 :Dy phosphor were placed at various locations at RPhL It is used for personnel monitoring. One set of TLD was exposed for a week long period while the other set was exposed only during activity handling, kept in the lead pot during the rest of the period. Dose measured by TLDs were compared with the dose estimated using the survey data for the respective locations as well as with the dose estimated using the activity handled by taking into account the time, distance and shielding. The maximum radiation level recorded during lab survey was used to estimate the TLD exposure during the period. It was observed that results on TLD dose measurement and estimated doses using survey results were of same order. The cumulative TLD dose recorded for week duration (168 h) was significantly higher than doses recorded by exposed TLD only during activity handling (8 h). It was expected that the TLD dose would not be more than dose estimated using radiation survey data, while in 3 among 8 experimental TLDs, the dose was ∼ 25% higher. This could be due to the movement of active material or open handling of activity do not get reflected during normal radiation survey and contribution from background radiation at the lab where those TLDs were placed. The individual dose of all the personnel working in different labs were well within the relevant dose limits indicating the safe working condition

The characteristics of CaF2:Tm crystals (TLD-300) irradiated by electromagnetic radiation

International Nuclear Information System (INIS)

Ben-Shachar, B.; Yona, S.; Laichter, Y.; German, U.; Weiser, G.

1985-09-01

The main characteristics of the CaF 2 :Tm crystals (TLD-300), as a dosimeter, were measured: the glow curve, sensitivity, linearity, fading and energy dependence for photons, and compared to those of LiF (TLD-100) and CaF 2 :Dy (TLD-200). It was found that CaF 2 :Tm can be used for environmental dosimetry by reading the crystals after four days. (Author)

Calibration of TLD badge to photons of energies above 6 MeV encountered in nuclear reactors

International Nuclear Information System (INIS)

Pradhan, A.S.; Bakshi, A.K.

1999-01-01

Response of CaSO 4 :Dy Teflon discs based TLD badge has been evaluated for radiation fields having photons of energy above 6 MeV, often encountered in nuclear power plants. Gamma ray response of the TLD disc under metal filter in the badge (used for evaluation of gamma ray doses) was found to increase by about 10% to photons above 6 MeV as compared to the response for reference calibration to 60 Co gamma rays. Response of discs under the open window and the plastic filter was found to be only 40-60% of that under metal filter. Thus, while measurement of whole body dose is not affected seriously, the estimation of beta dose in the mixed fields of high energy gamma rays and beta rays could be in serious error. In the above fields for situations having beta doses of about 1.65 times the gamma ray doses, the present use of dose evaluation will record beta dose as zero, a serious under estimation of beta ray doses. Study also provides an explanation to an anomalous situation where reading under window or plastic filter is much less than that under metal filter. These aspects of personal dosimetry need attention. (author)

Extra Dose Due to Extravehicular Activity During the NASA4 Mission, Measured by an On-Board TLD System

Energy Technology Data Exchange (ETDEWEB)

Deme, S.; Apathy, I.; Hejja, I.; Lang, E.; Feher, I. [Budapest (Hungary)

1999-07-01

A microprocessor-controlled on-board TLD system, 'Pille'96', was used during the NASA4 (1997) mission to monitor the cosmic radiation dose inside the Mir Space Station and to measure the extra dose to two astronauts in the course of their extravehicular activity (EVA). For the EVA dose measurements, CaSO{sub 4}:Dy bulb dosemeters were located in specially designed pockets of the ORLAN spacesuits. During an EVA lasting 6 h, the dose ratio inside and outside Mir was measured. During the EVA, Mir crossed the South Atlantic Anomaly three times. Taking into account the influence of these three crossings the mean EVA/internal dose rate ratio was 3.2. Internal dose mapping using CaSO{sub 4}:Dy dosemeters gave mean dose rates ranging from 9.3 to 18.3 {mu}Gy.h{sup -1} at locations where the shielding effect was not the same. Evaluation results of the high temperature region of LiF dosemeters are given to estimate the mean LET. (author)

Application of artificial neural network for development of an algorithm for TLD badge system in the mixed field dosimetry of X and gamma radiation in terms of Hp(10)

International Nuclear Information System (INIS)

Srivastava, K.; Bakshi, A.K.; Geetha, V.; Kher, R.K.; Dhar, V.K.

2005-01-01

ICRU has introduced new operational quantities for individual monitoring. Therefore it is required to develop an algorithm that gives direct response of the TLD badge in terms of the operational quantities. For this purpose and also to improve the precision in the mixed fields dosimetry, two methods were studied i)- analytical method by developing an algorithm based on of higher order polynomial fit of the data points for known delivered doses and ii) use of Artificial Neural Network (ANN). Study on the response of the TLD badge system based on CaSO 4 : Dy Teflon TLD discs in the mixed fields of X and gamma radiation in terms of operational quantity Hp(10) was carried out using the prevalent algorithm, algorithm developed using higher order polynomial and neural network predicted algorithm for different proportion of dose delivered by X and gamma radiations. It was found that the uncertainties in the dose response for few fields are beyond the acceptable limit for prevalent algorithm and within the acceptable limit for other two algorithms. Algorithm based on ANN gives higher precision in the mixed field of two radiations compared to other two algorithms. (author)

Direct measurement of annual β dose using TLD on porcelain

International Nuclear Information System (INIS)

Leung, P.L.; Stokes, M.J.; Xia Junding; Wang Weida; Zhou Zhixin

1999-01-01

In order to improve accuracy of TL authentication test for porcelain, a method of direct measurement of annual β dose using ultrathin TLD (CaSO 4 :Tm) on porcelain was studied. Since the TLD was placed into a hole left after sampling for the TL measurement, the method will not cause any new damage to the studied object. The results show that the technique is suitable for measuring annual β dose and improving accuracy of TL authentication test for both porcelain and pottery

Effect of thermal treatment on TL response of CaSO₄:Dy obtained using a new preparation method.

Science.gov (United States)

González, P R; Cruz-Zaragoza, E; Furetta, C; Azorín, J; Alcántara, B C

2013-05-01

We report the effect of thermal treatment on thermoluminescent (TL) sensitivity property of CaSO4:Dy obtained by a new preparation method at Instituto Nacional de Investigaciones Nucleares (ININ) of Mexico. Samples of phosphor powder were subjected to different thermal treatments respectively at 773, 873, 973 and 1,173K for 1h and then irradiated from 0.1 to 1,000 Gy gamma doses. Low energy dependence was analyzed too by irradiating with X-rays in the range of 16-145 keV. The results were normalized to the energy (1,252 keV) of (60)Co and they were compared with those obtained using the commercial dosimeters TLD-100. Also the kinetic parameters were determined by deconvolution of glow curve. Copyright © 2013 Elsevier Ltd. All rights reserved.

Measurement of absorbed dose for high energy electron using CaSO4: Tm-PTFE TLD

International Nuclear Information System (INIS)

Park, Myeong Hwan; Kim, Do Sung

2000-01-01

In this study, the highly sensitive CaSO 4 : Tm-PTFE TLDs has been fabricated for the purpose of measurement of high energy electron. CaSO 4 : Tm phosphor powder was mixed with polytetrafluoroethylene(PTFE) powder and moulded in a disk type(diameter 8.5mm, thickness 90mg/cm 2 ) by cold pressing. The absorbed dose distribution and ranges for high energy electron were measured by using the CaSO 4 : Tm-PTFE TLDs. The ranges determined were R 100 =3D14.5mm, R 50 =3D24.1mm and R p =3D31.8mm, respectively and the beam flatness, the variation of relative dose in 80% of the field size, was 4.5%. The fabricated CaSO 4 : Tm-PTFE TLDs may be utilized in radiation dosimetry for personal, absorbed dose and environmental monitoring.=20

Dosimetric behavior of thermoluminescent dosimeters at low doses in diagnostic radiology

International Nuclear Information System (INIS)

Del Sol F, S.; Garcia S, R.; Guzman M, J.; Sanchez G, D.; Rivera M, T.; Ramirez R, G.; Gaona, E.

2015-10-01

Thermoluminescent (Tl) characteristics of TLD-100, LiF:Mg,Cu,P, and CaSO 4 : Dy the under homogeneous field of X-ray beams of diagnostic irradiation and its verification using thermoluminescent dosimetry is presented. The irradiations were performed utilizing an X-ray beam generated by a Radiology Mexican Company: MRH-II E GMX 325-AF SBV-1 model, with Rotating Anode X-Ray Tube installed in the Hospital Juarez Norte de Mexico in Mexico City. Different thermoluminescent characteristics of dosimetric material were studied, such as, batch homogeneity, Tl glow curve, Tl response as a function of X-ray dose, reproducibility and fading. Materials were calibrated in terms of absorbed dose to the standard calibration distance and positioned in a generic Phantom was used. Dose verification and comparison with the measurements made with that obtained by TLD-100 were analyzed. Preliminary results indicate the dosimetric peak appears at 243, 236 and 277 ± 5 degrees C respectively, these peaks are in agreement with that reported in the literature. Tl glow curve as a function of X-ray dose showed a linearity in the range from 1.76 mGy up to 14.70 mGy for all materials. Fading for a period of one month at room temperature showed low fading LiF:Mg,Cu,P, medium and high for TLD-100 and CaSO 4 : Dy. The results suggest that the three materials are suitable for measurements at low doses in radiodiagnostic, however, for its dosimetric characteristics are most effective for individual applications: personal dosimetry and monitors limb (LiF:Mg,Cu,P), clinical dosimetry and environmental (TLD-100 and CaSO 4 : Dy). (Author)

Study of the OSL response of the CaF2:Dy (TLD-200) dosimeter

International Nuclear Information System (INIS)

Medeiros, Beatriz M.; Alencar, Marcus A.V. de

2013-01-01

The OSL dosimetry has become, in recent years, a successful technique in personal and environmental dosimetry due to high luminescence efficiency, excellent reproducibility, fast readout of signal and repeated and successive OSL measurements of the same dosimeter. Another factor that contributes to the increased use of OSL dosimetry is the use of the aluminum oxide doped with carbon (Al 2 O 3 :C) as dosimeter. Developed initially as thermoluminescent dosimeter, the Al 2 O 3 :C has an excellent OSL sensitivity, high efficiency, good linearity, low or no fading and excellent stability with respect to environmental conditions. However, the OSL dose response for aluminum oxide is linear only for low doses. For intermediate doses (doses in radiotherapy), the response is supralinear. For the values of high doses used in the processes of food irradiation and sterilization of surgical materials, the OSL signal of the aluminum oxide already saturated. Furthermore, the degree of supralinearity and the saturation value vary from sample to sample (∼ 30-300 Gy). Therefore, the use of aluminum oxide as OSL dosimeter is inappropriate in radiotherapy and in the irradiation industrial processes. The objective of this work is the study of the OSL properties of other dosimetric materials irradiated with values of intermediate and high dose to verify the applicability of the OSL dosimetry in radiotherapy and in the processes of food irradiation and sterilization of medical materials. The dosimetric material used in this work is the calcium fluoride doped with dysprosium (CaF 2 :Dy) produced by Harshaw and known commercially as TLD-200. The results demonstrate that the CaF 2 :Dy has OSL signal and the OSL dose response is linear in the range of 10 Gy to 300 Gy. Therefore, the dosimetry OSL with this dosimeter can be used in the evaluation of doses of the order of dozens to hundreds of grays. (author)

Production of thermoluminescent dosemeters based on MgB{sub 4}O{sub 7}: Dy and MgB{sub 4}O{sub 7}: Tm; Producao de dosimetros termoluminescentes a base de MgB{sub 4}O{sub 7}: Dy e MgB{sub 4}O{sub 7}: Tm

Energy Technology Data Exchange (ETDEWEB)

Souza, Luiza Freire de; Souza, Divanizia N., E-mail: luizaf25@hotmail.com, E-mail: divanizi@ufs.br [Universidade Federal de Sergipe (UFS), Sao Cristovao, SE (Brazil). Programa de Pos-Graduacao em Fisica

2013-07-01

The thermoluminescent dosimetry (TL) is a well-established technique for the detection of ionizing radiation in hospitals, clinics, and industrial establishments where there is the need to quantify the radiation. For this practice is require the use phosphors which are sensitive to radiation. Some phosphors are already commonly used in this practice, for example, TLD-100 (LiF: Mg, Ti), CaSO{sub 4}:Tm and CaSO{sub 4}:Dy. A compound that was most recently introduced in dosimetry and has many advantageous features to detect neutrons, electrons and gamma is the magnesium tetraborate (MgB{sub 4}O{sub 7}), but the undoped material is not good for dosimetry, since signal does not show satisfactory thermoluminescence. The present work presents the analysis of the compound MgB{sub 4}O{sub 7} when doped with rare earth elements, thulium (Tm) and dysprosium (Dy). The production of MgB{sub 4}O{sub 7}: Dy and MgB{sub 4}O{sub 7}: Tm occurred under acidic conditions. Following the process of crystal growth, several tests were made on phosphors produced to verify the quality of materials as TL dosimeter. Initially, was made the identification of the crystalline phases found in the material, using the technique of X-ray diffractometry, and then were evaluated and compared the TL emission curves of the crystals with two different types of dopants, to this, the samples were irradiated with different radiation sources: {sup 137}Cs (0,66 MeV), {sup 60}Co (1.25 MeV) and X-rays (0.41 MeV) and based on the results was evaluated the energy dependence of phosphors. Another characteristic analyzed, was the decay of TL signal for the material (fading). The results show that the material can be an excellent TL dosimeter when doped with rare earth elements Dy and Tm. (author)

Luminescence properties of pure and doped CaSO4 nanorods irradiated by 15 MeV e-beam

International Nuclear Information System (INIS)

Salah, Numan; Alharbi, Najlaa D.; Enani, Mohammad A.

2014-01-01

Calcium sulfate (CaSO 4 ) doped with proper activators is a highly sensitive phosphor used in different fields mainly for radiation dosimetry, lighting and display applications. In this work pure and doped nanorods of CaSO 4 were produced by the co-precipitation technique. Samples from this material doped with Ag, Cu, Dy, Eu and Tb were exposed to different doses of 15 MeV e-beam and studied for their thermoluminesence (TL) and photoluminescence (PL) properties. Color center formation leading to PL emissions were investigated before and after e-beam irradiation. The samples doped with rare earths elements (i.e. Dy, Eu and Tb) were observed to have thinner nanorods than the other samples and have higher absorption in the UV region. The Ag and Tb doped samples have poor TL response to e-beam, while those activated by Cu, Dy and Eu have strong glow peaks at around 123 °C. Quite linear response curves in the whole studied exposures i.e. 0.1–100 Gy were also observed in Cu and Dy doped samples. The PL results show that pure CaSO 4 nanorods have active color centers without irradiation, which could be enriched/modified by these impurities mainly rare earths and further enhanced by e-beam irradiation. Eu 3+ → Eu 2+ conversion is clearly observed in Eu doped sample after e-beam irradiation. These results show that these nanorods might be useful in lighting and display devices development

Operating experience of an automated TLD dispensing system at CORAL facility

International Nuclear Information System (INIS)

Ajoy, K.C.; Dhanasekaran, A.; Arun, R.; Yuvaraj, N.; Karthikeyan, D.; Dheeraj, R.; Akila, R.; Santhanam, R.; Rajagopal, V.; Kumar, Amudhu Ramesh

2016-01-01

Monitoring of exposures to occupational workers on individual basis is a regulatory requirement to demonstrate compliance that the dose to the workers is well within the dose limit. Over three decades for monitoring of external exposures, CaSO 4 based Thermo luminescence dosimeters (TLDs), which exhibit the required accuracy, reliability and ruggedness have been employed. TLD cards with unique identification number are loaded in plastic cassettes along with photographs are placed in wooden racks at the entry of the controlled area of the plant. However, there is always a chance that a TLD may be misplaced, used by others or there could be a deliberate act of misuse or abuse. To circumvent this it was decided to install an automated TLD dispensing system with individual TLD tracking as well as locking arrangement. CORAL reprocessing facility at IGCAR was the first to install one such system at Kalpakkam and the operating experience of the system for the last two years is brought out in this paper

Fading of CaSO4 thermoluminescent detectors after exposure to charged particles

Czech Academy of Sciences Publication Activity Database

Pachnerová Brabcová, Kateřina; Štěpán, Václav; Kubančák, Ján; Davídková, Marie; Ambrožová, Iva

2017-01-01

Roč. 106, č. 12 (2017), s. 569-572 ISSN 1350-4487 R&D Projects: GA ČR GJ15-16622Y Institutional support: RVO:61389005 Keywords : thermoluminescent detectors * CaSO4:Dy * fading * charged particles Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders OBOR OECD: Nuclear physics Impact factor: 1.442, year: 2016

Characterization and standardization of a thermoluminescent dosimetric system to ultraviolet and laser radiation using CaSO4:Dy

International Nuclear Information System (INIS)

Grossi, Fabio Henrique

2002-01-01

The photo transferred thermoluminescence (PTTL) was used to characterize a dosimetric system to the laser and ultraviolet radiation. Dysprosium activated calcium sulphate samples (CaSO 4 :Dy) used are produced at Instituto de Pesquisas Energeticas e Nucleares (IPEN) and have proved been an excellent dosimetric material for non ionizing radiation. PTTL signal was studied for UV radiation detection in the 220 to 450 nm range and for laser radiation in the 193 to 1.160 nm range. The samples presented more sensibility to the 193, 250, 310 and 337 nm wavelengths and no sensibility to infrared region. The samples presented linear PTTL in function of radiant exposure, excitation gamma dose in the range between 5 and 100 Gy and laser beam diameter between 2 and 6 nm. Another parameters studied were the angular dependence, UV lower exposure limit and PTTL signal optical fading. Spread laser radiation analysis was performed in the Ophthalmologic Department of Universidade Federal de Sao Paulo (UNIFESP) surgical center, showing that samples positioned as far as 4 m from laser source are sensitized to the laser radiation, as well as evaluating the laser exposure received by workers of medical area. A method to send the samples by mail was developed to the studies performed in the UNIFESP. (author)

Environmental dose measurement with microprocessor based portable TLD reader

International Nuclear Information System (INIS)

Deme, S.; Apathy, I.; Feher, I.

1996-01-01

Application of TL method for environmental gamma-radiation dosimetry involves uncertainty caused by the dose collected during the transport from the point of annealing to the place of exposure and back to the place of evaluation. Should an accident occur read out is delayed due to the need to transport to a laboratory equipped with a TLD reader. A portable reader capable of reading out the TL dosemeter at the place of exposure ('in situ TLD reader') eliminates the above mentioned disadvantages. We have developed a microprocessor based portable TLD reader for monitoring environmental gamma-radiation doses and for on board reading out of doses on space stations. The first version of our portable, battery operated reader (named Pille - 'butterfly') was made at the beginning of the 80s. These devices used CaSO 4 bulb dosemeters and the evaluation technique was based on analogue timing circuits and analogue to digital conversion of the photomultiplier current with a read out precision of 1 μGy and a measuring range up to 10 Gy. The measured values were displayed and manually recorded. The version with an external power supply was used for space dosimetry as an onboard TLD reader

Energy dependence of thermoluminescent response of CaSO{sub 4}:Dy, LiF:Mg and micro LiF:Mg,Ti in clinical beams of electrons by using different simulator objects; Dependencia energetica da resposta TL de dosimetros de CaSO{sub 4}:Dy, LiF:Mg e microLiF:Mg,Ti em feixes clinicos de eletrons utilizando diferentes objetos simuladores

Energy Technology Data Exchange (ETDEWEB)

Bravim, Amanda; Campos, Leticia Lucente, E-mail: abravin@ipen.b, E-mail: rsakuraba@einstein.b, E-mail: lcrodri@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Sakuraba, Roberto K.; Cruz, Jose Carlos da, E-mail: rsakuraba@einstein.b, E-mail: josecarlosc@einstein.b [Hospital Israelita Albert Einstein (HIAE), Sao Paulo, SP (Brazil)

2011-10-26

Yet not so widely applied in radiotherapy, the calcium sulfate doped with dysprosium (CaSO{sub 4}:Dy) is used in radioprotection and studies has been demonstrated its great potential for the dosimetry in radiotherapy. This work evaluates the energy dependence of the thermoluminescent answer of the CaSO{sub 4}:D, LiF:Mg,Ti (TLD-100) and micro LiF:Mg,Ti in clinical beams of electrons by using water simulators, PMMA and solid water

Comparative study of eye dose and chest dose received during radiopharmaceutical production processes

International Nuclear Information System (INIS)

Chindarkar, A.S.; Chavan, S.V.; Sawant, D.K.; Sahoo, L.; Gopalakrishnan, R.K.; Sneha, C.; Sachdev, S.S.; Dey, A.C.

2018-01-01

Radiopharmaceutical laboratory, BRIT, Vashi produces different radiopharmaceuticals of 131 I, 153 Sm, 99 Mo/ 99m Tc and 177 Lu. Principle gamma energies of these isotopes vary from 103 to 740 KeV and their maximum beta energies vary from 384 to 1214 KeV. In the light of the revised eye lens dose limit recommended in IAEA Basic Safety Standard Interim Edition No. GSR Part 3 (IAEA-2011), the study of radiation dose for eye lens was carried out using CaSO 4 : Dy based Thermo luminescence dosimeter (TLD). This TLD was worn at center of the forehead to measure eye lens dose. This TLD dose was then compared with chest TLD dose to deduce any correlation between these TLD doses. These TLD doses were assessed on quarterly basis. Eight quarter data of these TLD doses were compared

Comparison of the TL intensity of the sintered composites of CaSO4+Tm

International Nuclear Information System (INIS)

Junot, O.D.; Sousa, F.L. de; Chagas, M.A.P.; Souza, D.N.

2009-01-01

The objective of this work is to compare the thermoluminescent intensity (TL) of CaSO 4 +Tm, CaSO 4 +Tm+glass and glass+Tm composites for use as thermoluminescent dosimeter (TLD). The route used to prepare the CaSO 4 +Tm and the CaSO 4 +Tm+glass was by mixing 1 g of CaSO 4 with 0.02 g of thulium oxide (99,9% purity) and 0.3 g of commercial and colorless glass. To mixing the composites were taken to a magnetic stirrer for 30 min with 10 mL of distilled water for better homogenization. The powder mixtures were dried in a stove at 100 deg C for 24 h. After drying, it was added polyvinyl alcohol (PVA) to improve the binding material. The pellets were compacted by application of an uniaxial pressing and sintered at 700 deg C/ 6 h. The route used in the preparation of glass+Tm pellets was similar to one previously mentioned, except by the use of 1 g of glass and 0.02 of Tm. After the sintering, the pellets dimensions were 1 mm thick and 6 mm in diameter. All samples were irradiated by a beta source ( 90 Sr + 90 Y) and received doses from 1.00 Gy to 20 Gy. Each composite presented a characteristic emission curve. The dosimeter of CaSO 4 +Tm+glass presented two peaks, the first at 115 deg C, and the second, very intense, ate 150 deg C. The CaSO 4 +Tm dosimeter showed a less intense peak at 140 deg C and another, more intense, at 235 deg C. In the composites of glass+Tm, the most intense peak has a thermoluminescent signal 94,04% lower than the most intense peak of CaSO 4 +Tm+glass and 81.57% lower than the most intense peak of CaSO 4 +Tm. After the analysis of TL emission curves, we observed that the CaSO 4 +Tm+glass have the highest TL intensity and a TL response proportional to the dose absorbed. (author)

Quality control in medical radiology using T.L.D

International Nuclear Information System (INIS)

Rolemberg Silva, F.A.; Nascimento Souza, D. do

2006-01-01

In this work tests of quality control in beams of X rays have been carried out, at diagnostic level, of two radiological services equipments of Brazilian hospitals (Aracaju, SE). We obtained the air kerma and kerma rate values, the beams efficiency, the coherence between the luminous fields and the referring fields of irradiation and half-value layer to each equipment and set of parameters. The measures of direct form have been obtained using two ionization chambers, one cylindrical and another one with parallel plates. An optional method for accomplishment some of the tests were carried out with CaSO 4 :Dy + Teflon thermoluminescent dosimeters. The values of air kerma were evaluated for three tube voltage, 40, 60 and 81 kV at 1.0 m from the focus of the equipments. For each one of the voltages three distinct current values were chosen besides a fixed value of exposition time. The results showed that the values of air kerma varied between 8.0 μGy and 0.35 μGy. The T.L.D. have revealed useful for the measures if the response to the dose is previously known for each set of beam parameters used for the irradiations. Otherwise, the tests with the dosimeters can serve to evaluate the beams conditions and their reproducibility. The evaluation results of coherence between the luminous fields and the irradiation fields demonstrated that the difference between the radiation and the luminous fields did not exceed 2% of the distance between the focal point and the film. We found satisfactory values for half-value layer. (author)

Study of thermoluminescence emissions of dosimetric phosphors; the detection of intermediate neutrons

International Nuclear Information System (INIS)

Santos, E.N. dos.

1979-01-01

Thermally stimulated luminescence (TSL) studies have been carried out in cold-pressed CaSO 4 +DY 2 O 3 +KCl (specimen 1) and natural CaF 2 +DY 2 O 3 + KCl (specimen 2) polycrystaline samples. The ratios of the TSL sensivities of specimens 1 and 2 relative to that of 6 LiF:Mg;Ti (TLD-600) are found to be 24 and 3, respectively. The minimum detectable neutron fluence has been determined to be approximately 3.5X10 5 n/cm 2 . The determination of the effective half-life of the TSL emission lead to the identification of the isotope responsible for the self-irradiation of the specimens: 165 66 DY. (F.E.) [pt

Reproducibility Test for Thermoluminescence Dosimeter (TLD) Using TLD Radpro

International Nuclear Information System (INIS)

Nur Khairunisa Zahidi; Ahmad Bazlie Abdul Kadir; Faizal Azrin Abdul Razalim

2016-01-01

Thermoluminescence dosimeters (TLD) as one type of dosimeter which are often used to substitute the film badge. Like a film badge, it is worn for a period of time and then must be processed to determine the dose received. This study was to test the reproducibility of TLD using Radpro reader. This study aimed to determine the dose obtained by TLD-100 chips when irradiated with Co-60 gamma source and to test the effectiveness of TLD Radpro reader as a machine to analyse the TLD. Ten chips of TLD -100 were irradiated using Eldorado machine with Co-60 source at a distance of 5 meters from the source with 2 mSv dose exposure. After the irradiation process, TLD-100 chips were read using the TLD Radpro reader. These steps will be repeated for nine times to obtain reproducibility coefficient, r i . The readings of dose obtained from experiment was almost equivalent to the actual dose. Results shows that the average value obtained for reproducibility coefficient, r i is 6.39 % which is less than 10 %. As conclusion, the dose obtained from experiment considered accurate because its value were almost equivalent to the actual dose and TLD Radpro was verified as a good reader to analyse the TLD. (author)

CaSO{sub 4}:Dy microphosphor for thermal neutron dosimetry

Energy Technology Data Exchange (ETDEWEB)

Bhadane, Mahesh S. [Microtron Accelerator Laboratory, Department of Physics, Savitribai Phule Pune University, Pune 411007 (India); Mandlik, Nandkumar [Department of Physics, Fergusson College, Savitribai Phule Pune University, Pune 411007 (India); Patil, B.J. [Department of Physics, Abasaheb Garware College, Pune 411004 (India); Dahiwale, S.S.; Sature, K.R.; Bhoraskar, V.N. [Microtron Accelerator Laboratory, Department of Physics, Savitribai Phule Pune University, Pune 411007 (India); Dhole, S.D., E-mail: sanjay@physics.unipune.ac.in [Microtron Accelerator Laboratory, Department of Physics, Savitribai Phule Pune University, Pune 411007 (India)

2016-02-15

Dysprosium-doped calcium sulphate (CaSO{sub 4}:Dy) microphosphor was synthesized by acid re-crystallization method and its thermoluminescence (TL) properties irradiated with thermal neutrons was studied. Structural and morphological characteristics have been studied using X-ray diffraction and SEM which mainly exhibits a orthorhombic structure with particle size of 200 to 250 µm. Moreover, thermal neutron dosimetric characteristics of the microphosphor such as thermoluminescence glow curve, TL dose–response have been studied. This microphosphor powder represents a TL glow peak (T{sub max}) centered at around 240 °C. The TL response of CaSO{sub 4}:Dy microphosphor as a function of thermal neutron fluence is observed to be very linear upto the fluence of 52×10{sup 11} n/cm{sup 2} and further saturates. In addition, TL glow curves were deconvoluted by computerized glow curve deconvolution (CGCD) method and corresponding trapping parameters have been determined. It has been found that for every deconvoluted peak there is change in the order of kinetics. Overall, the experimental results show that the CaSO{sub 4}:Dy microphosphor can have potential to be an effective thermal neutron dosimetry. - Highlights: • Acid-recrystallization method is used to prepare CaSO{sub 4}:Dy microphosphor • CaSO{sub 4}:Dy phosphor irradiated thermal neutrons for dosimetric application. • TL response curve showed to be a perfect linear. • Trapping parameters has been calculated using CGCD curve fitting.

Advances in the synthesis of new Europium doped CaSO4 phosphors and their thermoluminescence characterization

International Nuclear Information System (INIS)

Bernal, R.; Garcia-Haro, A.R.; Machi, L.; Brown, F.; Perez-Salas, R.; Castano, V.M.; Cruz-Vazquez, C.

2008-01-01

Novel self-agglomerating Eu doped CaSO 4 phosphors were synthesized by a cheap, easy, and environmental friendly chemical route. Pellet-shaped sintered samples were obtained without any binding material, and exposed to beta particle irradiation. The thermoluminescence (TL) response in the 0.08-2.6 Gy dose range increased linearly as the radiation dose increased. Glow curves exhibit the most intense maximum close to 200 deg. C, and two much less intense maxima at 250 and 330 deg. C when a 5 deg. C/s heating rate is used. No TL peaks shift is observed when dose changes, which is characteristic of first order kinetics TL processes. The whole glow curve displays a remarkable stability under storage at room temperature. The main peak intensity is 2.5 times greater than that of the TLD-100. The method here reported can be used to synthesize CaSO 4 with other dopants

Photon and neutron energy response of Thermoluminescent (TL) dosimeters

International Nuclear Information System (INIS)

Thilagam, L.; Priya, M.R.; Mohapatra, D.K.

2018-01-01

Theoretical Monte Carlo (MC) simulations are carried out to investigate the relative thermoluminesence (TL) response of the most commonly used TLD materials to a wide range of photon energy. The effect of polytetrafluoroethylene (PTFE) on TL response of CaSO 4 :Dy is also studied. Additionally, the neutron response of LiF:Mg,Ti TL materials with different concentrations of 6 Li is estimated in terms of the number of 6 Li(n, t) 4 He capture reactions for a wider neutron energy

Effects of 3d-4f magnetic exchange interactions on the dynamics of the magnetization of Dy(III)-M(II)-Dy(III) trinuclear clusters.

Science.gov (United States)

Pointillart, Fabrice; Bernot, Kevin; Sessoli, Roberta; Gatteschi, Dante

2007-01-01

[{Dy(hfac)(3)}(2){Fe(bpca)(2)}] x CHCl(3) ([Dy(2)Fe]) and [{Dy(hfac)(3)}(2){Ni(bpca)(2)}]CHCl(3) ([Dy(2)Ni]) (in which hfac(-)=1,1,1,5,5,5-hexafluoroacetylacetonate and bpca(-)=bis(2-pyridylcarbonyl)amine anion) were synthesized and characterized. Single-crystal X-ray diffraction shows that [Dy(2)Fe] and [Dy(2)Ni] are linear trinuclear complexes. Static magnetic susceptibility measurements reveal a weak ferromagnetic exchange interaction between Ni(II) and Dy(III) ions in [Dy(2)Ni], whereas the use of the diamagnetic Fe(II) ion leads to the absence of magnetic exchange interaction in [Dy(2)Fe]. Dynamic susceptibility measurements show a thermally activated behavior with the energy barrier of 9.7 and 4.9 K for the [Dy(2)Fe] and [Dy(2)Ni] complexes, respectively. A surprising negative effect of the ferromagnetic exchange interaction has been found and has been attributed to the structural conformation of these trinuclear complexes.

Synthesis and luminescence properties of novel LiSrPO{sub 4}:Dy{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Sun, Jiayue, E-mail: jiayue_sun@126.com [School of Science, Beijing Technology and Business University, Beijing 100048 (China); Zhang, Xiangyan [School of Science, Beijing Technology and Business University, Beijing 100048 (China); Xia, Zhiguo, E-mail: xiazg426@yahoo.com.cn [School of Materials Sciences and Technology, China University of Geosciences, Beijing 100083 (China); Du, Haiyan [School of Science, Beijing Technology and Business University, Beijing 100048 (China)

2011-11-15

Graphical abstract: Novel LiSrPO4:Dy{sup 3+} phosphors were synthesized by solid-state reaction, and Dy{sup 3+}-doped concentration dependent luminescence properties, concentration quenching effect and the decay times were investigated in detail. Highlights: {yields} LiSrPO{sub 4}:Dy{sup 3+} could be excited by UV light and exhibited blue and yellow emission. {yields} Concentration quenching effect of LiSrPO{sub 4}:Dy{sup 3+} samples were investigated in detail. {yields} Decay times are estimated to be 0.57-0.89 ms for Dy{sup 3+} in LiSrPO{sub 4} host. -- Abstract: Novel LiSrPO{sub 4}:Dy{sup 3+} phosphors for white light-emitting diodes (w-LEDs) were synthesized by the conventional solid-state reaction. X-ray powder diffraction (XRD) analysis confirmed the phase formation of LiSrPO{sub 4}:Dy{sup 3+} materials. Luminescence properties results showed that the phosphor could be efficiently excited by the UV-vis light region from 250 to 460 nm, and it exhibited blue (483 nm) and yellow (574 nm) emission corresponding to {sup 4}F{sub 9/2} {yields} {sup 6}H{sub 15/2} transitions and {sup 4}F{sub 9/2} {yields} {sup 6}H{sub 13}/{sub 2} transitions, respectively. The luminescence intensity of LiSrPO{sub 4}:xDy{sup 3+} phosphor firstly increased and then decreased with increasing Dy{sup 3+} concentration, and reached the maximum at x = 0.03. It was found that concentration quenching occurred as a result of dipole-dipole interaction according to the Dexter's theory. The decay time was also determined for various concentrations of Dy{sup 3+} in LiSrPO{sub 4}.

Blue–green afterglow of BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Zhai, Bao-gai [School of Mathematics and Physics, Changzhou University, Jiangsu 213164 (China); Ma, Qing-lan [School of Mathematics and Physics, Changzhou University, Jiangsu 213164 (China); School of Electronics and Information, Nantong University, Jiangsu 226019 (China); Xiong, Rui [School of Physics and Technology, Wuhan University, Hubei 430072 (China); Li, Xiazhang [Analysis and Testing Center, Changzhou University, Jiangsu 213164 (China); Huang, Yuan Ming, E-mail: dongshanisland@126.com [School of Mathematics and Physics, Changzhou University, Jiangsu 213164 (China)

2016-03-15

Highlights: • Afterglow can be achieved when Eu{sup 2+} is absent in the DyAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors. • The afterglow of DyAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors is discernible to naked eyes for minutes. • Dy{sup 3+} introduced trap centers are believed to be responsible for the afterglow. - Abstract: Dy{sup 3+} doped barium aluminate (BaAl{sub 2}O{sub 4}:Dy{sup 3+}) phosphors were prepared via the sol–gel combustion route at the ignition temperature of 600 °C. The phosphors were characterized with X-ray diffractometry, scanning electron microscopy, transmission electron microscopy, photoluminescence spectroscopy, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Regardless of the absence of Eu{sup 2+} luminescent centers, broadband blue–green afterglow with its peak at about 490 nm was recorded in the BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors. The decay profile of the blue–green afterglow can be best fitted into a two-component exponential function with the two lifetime decay constants to be 8.81 and 45.25 s, respectively. The observation of blue–green afterglow from BaAl{sub 2}O{sub 4}:Dy{sup 3+} in the absence of Eu{sup 2+} provides unique opportunity in unveiling the afterglow mechanisms of rare-earth doped alkaline-metal aluminates. Possible mechanisms on the blue–green afterglow in BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors are discussed in terms of the Dy{sup 3+} ions introduced trap centers as well as luminescent centers in the crystal lattice.

Facile synthesis, structural characterization, and photoluminescence mechanism of Dy3+ doped YVO4 and Ca2+ co-doped YVO4:Dy3+ nano-lattices

Science.gov (United States)

Dhiren Meetei, Sanoujam; Deben Singh, Mutum; Dorendrajit Singh, Shougaijam

2014-05-01

Light plays a vital role in the evolution of life. From sunlight to candle-light and then to other form of lighting devices, human beings are utilizing light since time immemorial. Lighting devices such as conventional incandescent lamp and fluorescent lamp have been replaced by Light Emitting Diodes (LEDs) for the later is cheap, durable, etc. Now-a-days, phosphor converted LEDs have been burning issues in the fabrication of lighting devices. Especially, lanthanide ion(s) doped phosphors are of great interest for the same. However, doped phosphors have a limitation of luminescence quenching, i.e., instead of increasing luminescence on increasing dopant concentration, the luminescence decreases. Therefore, it must be rectified by one or other means so as to get maximum desirable intensity for uses in display or lighting devices. In the present work, YVO4:Dy3+ and YVO4:Dy3+/Ca2+ nano-lattices are synthesized by a facile technique. Structural characterizations such as x-ray diffraction, SEM, TEM, HRTEM, and Selected Area Electron Diffraction (SAED) of the samples are reported. Photoluminescence (PL) excitation and emission, enhanced mechanism, and lifetime are thoroughly discussed. PL intensity of the quenched YVO4:Dy3+ is made increased up to 432.63% by Ca2+ co-doping. Role of the Ca2+ on the luminescence enhanced mechanism of YVO4:Dy3+/Ca2+ is elucidated.

Luminescence studies of SrAl_2O_4:Dy"3"+ nanophosphors

International Nuclear Information System (INIS)

Sharma, Ravi

2016-01-01

Nanosized strontium aluminate phosphors activated by Dy"3"+ were prepared by combustion as well as by solid state reaction method. Nanophosphor was prepared by these methods at reaction temperatures 600°C and 1200°C respectively. Powder X-ray diffraction (XRD), scanning electron microscope analysis was used to characterize the prepared product. Themonoclinic phase was observed in the XRD pattern. The particle size of the samples was calculated around 35 nm. The SEM images show irregular shape of the prepared nanophosphor. Two peaks were found in the Mechanoluminescence (ML) response curve plotted between time and ML intensity. The H_3BO_3 added strontium aluminate phosphors activated with Dy show more bright ML peak as compared to the powders of SrAl_2O_4:Dy"3"+ without H_3BO_3. It was found that the PL and ML intensity increases with increasing concentration of Dy. The intensity becomes maximum for 3% of Dy. The photoluminescence emission shows two intense fluorescence transitions peaks at 498 nm and 583 nm, "4F_9_/_2 → "6H_1_5_/_2 in the blue and "4F_9_/_2 → "6H_1_3_/_2 in the yellow-orange wavelength region. (author)

Synthesis and luminescence characteristics of Dy{sup 3+} doped KLa(PO{sub 3}){sub 4}

Energy Technology Data Exchange (ETDEWEB)

Chemingui, S.; Ferhi, M., E-mail: ferhi.mounir@gmail.com; Horchani-Naifer, K.; Férid, M.

2015-10-15

Polycrystalline powders of KLa{sub (1−x)}Dy{sub x}(PO{sub 3}){sub 4} (x=0.5%, 1%, 5% and 10%) with linear chain have been grown by solid state reaction. The obtained powders are characterized by X-ray powder diffraction, FTIR and Raman spectroscopies. Emission, excitation spectra and decay curves analysis have been used to study the spectroscopic properties of Dy{sup 3+} in KLa(PO{sub 3}){sub 4}. The photoluminescence spectra show two characteristic blue and yellow bands of Dy{sup 3+}. The yellow-to-blue emission intensity ratios and CIE chromaticity coordinates have been determined from emission spectra to evaluate the emitted light as function of Dy{sup 3+} concentration. The measured decay rates for {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} deviated from exponential to non-exponential shape with increase of Dy{sup 3+} concentration. The observed non-exponential behavior of the decay curve has been fitted to Inokuti–Hirayama model, which indicates that the energy transfer between the donor and the acceptor is of dipole–dipole nature. The energy transfer, between the donor (excited Dy{sup 3+}) and the acceptor (unexcited Dy{sup 3+}), increases with Dy{sup 3+} ions concentration. - Highlights: • Polycrystalline powders of KLa{sub (1−x)}Dy{sub x}(PO{sub 3}){sub 4} were grown by solid state reaction. • The obtained samples are characterized by XRD, FTIR and Raman spectroscopies. • The luminescent properties of Dy{sup 3+} in KLa(PO{sub 3}){sub 4} are investigated. • Lifetime and chromatic coordinates depend strongly on Dy{sup 3+} concentration. • White and blue emissions are obtained at high and low concentration, respectively.

Neutron dosimetry using activation of thermoluminescent CaSO 4

Science.gov (United States)

Azorín, Juan; Gutiérrez, Alicia

1984-11-01

Sulfur activation in calcium sulfate doped with dysprosium (CaSO 4:Dy) thermoluminescent powder, which is bound in pure sulfur, has been used to measure the fast neutron dose at the tangential beam port of a Triga Mark III reactor. After a post-irradiation time of 3 d, the dosimeters were annealed at 600°C for 30 min in order to erase all the thermoluminescence acquired during the irradiation. The dosimeters were then stored to allow self-irradiation by betas from 32P produced by sulfur activation. The thermoluminescent signal accumulated during a post-irradiation time of 20 d due to a neutron fluence of 2.2 × 10 11 n/cm 2 was equivalent to an absorbed dose of 10 mGy of 60Co gamma rays. The thermoluminescence as a function of fast neutron dose fitted to a straight line on a log-log scale from 1 Gy to 10 4Gy.

Application of combined TLD and CR-39 PNTD method for measurement of total dose and dose equivalent on ISS

International Nuclear Information System (INIS)

Benton, E.R.; Deme, S.; Apathy, I.

2006-01-01

To date, no single passive detector has been found that measures dose equivalent from ionizing radiation exposure in low-Earth orbit. We have developed the I.S.S. Passive Dosimetry System (P.D.S.), utilizing a combination of TLD in the form of the self-contained Pille TLD system and stacks of CR-39 plastic nuclear track detector (P.N.T.D.) oriented in three mutually orthogonal directions, to measure total dose and dose equivalent aboard the International Space Station (I.S.S.). The Pille TLD system, consisting on an on board reader and a large number of Ca 2 SO 4 :Dy TLD cells, is used to measure absorbed dose. The Pille TLD cells are read out and annealed by the I.S.S. crew on orbit, such that dose information for any time period or condition, e.g. for E.V.A. or following a solar particle event, is immediately available. Near-tissue equivalent CR-39 P.N.T.D. provides Let spectrum, dose, and dose equivalent from charged particles of LET ∞ H 2 O ≥ 10 keV/μm, including the secondaries produced in interactions with high-energy neutrons. Dose information from CR-39 P.N.T.D. is used to correct the absorbed dose component ≥ 10 keV/μm measured in TLD to obtain total dose. Dose equivalent from CR-39 P.N.T.D. is combined with the dose component <10 keV/μm measured in TLD to obtain total dose equivalent. Dose rates ranging from 165 to 250 μGy/day and dose equivalent rates ranging from 340 to 450 μSv/day were measured aboard I.S.S. during the Expedition 2 mission in 2001. Results from the P.D.S. are consistent with those from other passive detectors tested as part of the ground-based I.C.C.H.I.B.A.N. intercomparison of space radiation dosimeters. (authors)

Dosimetry characteristics of thermoluminescent Li2B4O7:Cu phosphor

International Nuclear Information System (INIS)

Lakshmanan, A.R.; Chandra, B.; Bhatt, R.C.

1981-01-01

Preliminary investigations on the radiation dosimetry characteristics of Li 2 B 4 O 7 :Cu TLD phosphor are described. The major TL peak in this phosphor occurs at 230 0 C and its TL sensitivity to gamma radiation is two to three times higher than that of LiF TLD-100. The gamma dose Vs TL response of this peak is linear (within +- 20%) in the dose range 0.3 mGy-3x10 2 Gy above which saturation sets in. Its TL response for 30 keV X-rays is about 20% lower than that for 60 Coγ-rays. On annealing at 300 0 C, the phosphor gets slightly discoloured (brownish). This results in the reduction of the TL sensitivity by about 20 - 25%. The phosphor does not exhibit either sensitization or damage even after a gamma dose of 10 3 Gy. The TL emission spectrum has a broad peak at 360 nm. The intrinsic TL sensitivity of virgin Li 2 B 4 O 7 :Cu to 253.7 nm UV radiation is nearly 50 times higher than that of CaSO 4 :Dy. The post-irradiation fading in Li 2 B 4 O 7 :Cu at ambient temperature and humidity conditions is, however, less than 10% in 17 days. These characteristics indicate that Li 2 B 4 O 7 :Cu is a promising phosphor for ionizing as well as UV radiation dosimetry. (author)

Bioremediation using Novosphingobium strain DY4 for 2,4-dichlorophenoxyacetic acid-contaminated soil and impact on microbial community structure.

Science.gov (United States)

Dai, Yu; Li, Ningning; Zhao, Qun; Xie, Shuguang

2015-04-01

The herbicide 2,4-dichlorophenoxyacetic acid (2,4-D) is commonly used for weed control. The ubiquity of 2,4-D has gained increasing environmental concerns. Biodegradation is an attractive way to clean up 2,4-D in contaminated soil. However, information on the bioaugmentation trial for remediating contaminated soil is still very limited. The impact of bioaugmentation using 2,4-D-degraders on soil microbial community remains unknown. The present study investigated the bioremediation potential of a novel degrader (strain DY4) for heavily 2,4-D-polluted soil and its bioaugmentation impact on microbial community structure. The strain DY4 was classified as a Novosphingobium species within class Alphaproteobacteria and harbored 2,4-D-degrading TfdAα gene. More than 50 and 95 % of the herbicide could be dissipated in bioaugmented soil (amended with 200 mg/kg 2,4-D) respectively in 3-4 and 5-7 days after inoculation of Novosphingobium strain DY4. A significant growth of the strain DY4 was observed in bioaugmented soil with the biodegradation of 2,4-D. Moreover, herbicide application significantly altered soil bacterial community structure but bioaumentation using the strain DY4 showed a relatively weak impact.

Effect of the temperature and relative humidity in dosemeters used for personnel monitoring

International Nuclear Information System (INIS)

Antonio Filho, J.

1982-12-01

The systematics of the combined effect of temperature and humidity on photographic dosimeters of the type Agfa-Gevaert, Kodak type II, III and the thermoluminescent dosimeters LiF:Mg,Ti (TLD-100, Harshaw), D-CaSO 4 :Dy-0,4 (Teledyne), e CaSO 4 :Dy+NaCl (IPEN), used in personal monitoring in Brazil was investigated, in the temperature range of 20 0 C to 50 0 C and relative humidity of 65% to 95%, in order to determine the best manner of utilization of these detectors in Brazilian climatic conditions. The dosimeters were studied in different forms of packing-sheet such as aluminezed paper and polyethylene. For the determination of the systematics, the dosimeters were irradiated in three conditions: before, during and after of storage in climatic chambers to a maximum period of 60 days. It was found that the dosimetric filmes and thermoluminescent dosimeter CaSO 4 :Dy+NaCl without protection, presented a high dependence to temperature and humidity, and when protected presented good results. Therefore, the best manner of utilization of these monitors in environments with relative humidity and temperature greater them 75% and 30 0 C respectively, is achieved with the protection of aluminized paper. The LiF:Mg,Ti and D+CaSO 4 :Dy-0,4 dosimeters can be utilized in their original form because they presented low dependence with humidity and temperature in the range studied. (Author) [pt

Evaluation of thermoluminescent dosimeters using water equivalent phantoms for application in clinical electrons beams dosimetry

International Nuclear Information System (INIS)

Bravim, Amanda

2010-01-01

The dosimetry in Radiotherapy provides the calibration of the radiation beam as well as the quality control of the dose in the clinical routine. Its main objective is to determine with greater accuracy the dose absorbed by the tumor. This study aimed to evaluate the behavior of three thermoluminescent dosimeters for the clinical electron beam dosimetry. The performance of the calcium sulfate detector doped with dysprosium (CaSO 4 : Dy) produced by IPEN was compared with two dosimeters commercially available by Harshaw. Both are named TLD-100, however they differ in their dimensions. The dosimeters were evaluated using water, solid water (RMI-457) and PMMA phantoms in different exposure fields for 4, 6, 9, 12 and 16 MeV electron beam energies. It was also performed measurements in photon beams of 6 and 15 MV (2 and 5 MeV) only for comparison. The dose-response curves were obtained for the 60 Co gamma radiation in air and under conditions of electronic equilibrium, both for clinical beam of photons and electrons in maximum dose depths. The sensitivity, reproducibility, intrinsic efficiency and energy dependence response of dosimeters were studied. The CaSO 4 : Dy showed the same behavior of TLD-100, demonstrating only an advantage in the sensitivity to the beams and radiation doses studied. Thus, the dosimeter produced by IPEN can be considered a new alternative for dosimetry in Radiotherapy departments. (author)

Thermoluminescence kinetic analysis and dosimetry features of MgSO4:Dy and MgSO4:Cu nano-rods

International Nuclear Information System (INIS)

Zahedifar, M.; Almasifard, F.; Sadeghi, E.; Biroon, M. Kashefi; Ramazani- Moghaddam-Arani, A.

2016-01-01

MgSO 4 :Dy and MgSO 4 :Cu nano-rods (NRs) were synthesized for the first time by semi co- precipitation method. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS) were utilized for sample characterization. The optimum amount of dysprosium and copper concentrations were obtained both at 0.1 mol% in MgSO 4 :Dy and MgSO 4 :Cu NRs. T m -T stop and computerized glow curve deconvolution (CGCD) methods were used for identifying the number of component glow peaks and kinetic parameters of the synthesized NRs. Initial rise and variable heating rate methods were also used to ensure the reliability of obtained kinetic parameters. Results show that the TL sensitivity of MgSO 4 :Dy is about 7 times more than that of magnesium sulfate doped with Cu. The TL dose response of MgSO 4 :Dy and MgSO 4 :Cu NRs are linear up to absorbed dose of 10 KGy. Other TL dosimetry characteristics of the produced NRs are also presented and discussed. - Highlights: • MgSO4:Dy and MgSO4:Cu nano-rods were synthesized for the first time. • Thermoluminescence dosimetry properties were studied. • The nano-phosphors showed linear dose response up to very high dose levels. • The synthesized nano-rods have potential application for high dose dosimetry.

Indoor gamma dose measurements in Gudalore (India) using TLD

International Nuclear Information System (INIS)

Sivakumar, R.; Selvasekarapandian, S.; Mugunthamanikandan, N.; Raghunath, V.M.

2002-01-01

Indoor gamma radiation dose rates were measured inside residential buildings in Gudalore using a CaSO 4 : Dy thermoluminescent dosimeter for 1 year . Significant seasonal variations are observed. The highest dose rate is observed during summer and the lowest in winter. The dose rates observed are between 77.9 and 229.3 nGy h -1 and may be attributed to the type of building materials used in the dwellings monitored. The calculated mean annual effective dose equivalent rates range between 477.6 μSv y -1 , for the inhabitants of mud houses to 1406.3 μSv y -1 , for those living in terrace houses made of cement and brick

Analysis of personnel monitoring control card data

International Nuclear Information System (INIS)

Ande, C.D.; Sneha, C.; Madhumita, B.; Bakshi, A.K.; Datta, D.

2018-01-01

In India, personnel monitoring of radiation workers for X-, beta- and gamma- radiation is carried out using a thermoluminescence dosemeter (TLD) system based on CaSO 4 :Dy Teflon TLD disc. A large number of radiation workers get very low occupational doses and their doses are reported as zero since it is not above detectable limits. Therefore, the detection of low levels of occupational dose over and above the natural background assumes great importance. In the present system, the estimation of the background dose is achieved by use of control dosemeters. An analysis of the readings of the control dosimeters sent to various institutions was carried out to arrive at conclusions regarding the validity of the use of control dosimeter

The assessment of personal dose due to external radiation

International Nuclear Information System (INIS)

Boas, J.F.; Young, J.G.

1990-01-01

The fundamental basis of thermoluminescent dosimetry (TLD) is discussed and a number of considerations in the measurement of thermoluminescence described, with particular reference to CaSO 4 :Dy. The steps taken to convert a thermoluminescence measurement to an exposure and then an absorbed dose are outlined. The calculation of effective dose equivalents due to external exposure to γ-radiation in a number of situations commonly encountered in a uranium mine is discussed. Factors which may affect the accuracy of external dose assessments are described

BaSO4:Eu as an energy independent thermoluminescent radiation dosimeter for gamma rays and C6+ ion beam

Science.gov (United States)

Sharma, Kanika; Bahl, Shaila; Singh, Birendra; Kumar, Pratik; Lochab, S. P.; Pandey, Anant

2018-04-01

BaSO4:Eu nanophosphor is delicately optimized by varying the concentration of the impurity element and compared to the commercially available thermoluminescent dosimeter (TLD) LiF:Mg,Ti (TLD-100) and by extension also to CaSO4:Dy (TLD-900) so as to achieve its maximum thermoluminescence (TL) sensitivity. Further, the energy dependence property of this barite nanophosphor is also explored at length by exposing the phosphor with 1.25 MeV of Co-60, 0.662 MeV of Cs-137, 85 MeV and 65 MeV of Carbon ion beams. Various batches of the phosphor at hand (with impurity concentrations being 0.05, 0.10, 0.20, 0.50 and 1.00 mol%) are prepared by the chemical co-precipitation method out of which BaSO4:Eu with 0.20 mol% Eu exhibits the maximum TL sensitivity. Further, the optimized nanophosphor exhibits a whopping 28.52 times higher TL sensitivity than the commercially available TLD-100 and 1.426 times higher sensitivity than TLD-900, a noteworthy linear response curve for an exceptionally wide range of doses i.e. 10 Gy to 2 kGy and a simple glow curve structure. Furthermore, when the newly optimized nanophosphor is exposed with two different energies of gamma radiations, namely 1.25 MeV of Co-60 (dose range- 10-300 Gy) and 0.662 MeV of Cs-137 (dose range- 1-300 Gy), it is observed that the shape and structure of the glow curves remain remarkably similar for different energies of radiation while the TL response curve shows little to no variation. When exposed to different energies of carbon ion beam BaSO4:Eu displays energy independence at lower doses i.e. from 6.059 to 14.497 kGy. Finally, even though energy independence is lost at higher doses, the material shows high sensitivity to higher energy (85 MeV) of carbon beam compared to the lower energy (65 MeV of C6+) and saturation is apparent only after 121.199 kGy. Therefore the present nanophosphor displays potential as an energy independent TLD.

Molecular assembly and magnetic dynamics of two novel Dy6 and Dy8 aggregates.

Science.gov (United States)

Guo, Yun-Nan; Chen, Xiao-Hua; Xue, Shufang; Tang, Jinkui

2012-04-02

Complexation of dysprosium(III) with the heterodonor chelating ligand o-vanillin picolinoylhydrazone (H(2)ovph) in the presence of a carbonato ligand affords two novel Dy(6) and Dy(8) clusters, namely, [Dy(6)(ovph)(4)(Hpvph)(2)Cl(4)(H(2)O)(2)(CO(3))(2)]·CH(3)OH·H(2)O·CH(3)CN (2) and [Dy(8)(ovph)(8)(CO(3))(4)(H(2)O)(8)]·12CH(3)CN·6H(2)O (3). Compound 2 is composed of three petals of the Dy(2) units linked by two carbonato ligands, forming a triangular prism arrangement, while compound 3 possesses an octanuclear core with an unprecedented tub conformation, in which Dy(ovph) fragments are attached to the sides of the carbonato core. The static and dynamic magnetic properties are reported and discussed. In the Dy(6) aggregate, three Dy(2) "skeletons", having been well preserved (see the scheme), contribute to the single-molecule-magnet behavior with a relatively slow tunneling rate, while the Dy(8) cluster only exhibits a rather small relaxation barrier.

High-efficient, bicolor-emitting GdVO_4:Dy"3"+ phosphor under near ultraviolet excitation

International Nuclear Information System (INIS)

Lu, Jinjin; Zhou, Jia; Jia, Huayu; Tian, Yue

2015-01-01

Bicolor emitting GdVO_4:Dy"3"+ phosphor with short columniation-shape was prepared via a simple co-precipitation process. The optimal doping concentration for obtaining maximal luminescent intensity was confirmed to be 0.3 mol% and the electric dipole–dipole interaction is responsible for concentration quenching of Dy"3"+ emission in GdVO_4 phosphor. In order to evaluate the luminescent performance of as-prepared phosphor, the luminescent efficiency and color coordinates were studied. The results show that luminescent efficiency of this phosphor is very high under near UV excitation and twice times higher than commercial Y_2O_2S:Eu"3"+ phosphor. In addition, the color coordinates for optimal Dy"3"+ concentration are (0.339, 0.379), which are close to equal energy point. Therefore, the GdVO_4:Dy"3"+ phosphor may have potential application for solid state lighting.

Application of thermoluminescent dosimeters (CaSO4:Dy) in the evaluation of the dose in ornamental granites of Pernambuco, Brazil

International Nuclear Information System (INIS)

Rocha, Edilson Accioly; Cardoso, Jorge J.R.F.; Santos Junior, Jose A. dos; Silva, Cleomacio M. da

2007-01-01

The granites of Pernambuco are being used as ornamental rocks, and besides being commercialized in our state. They are also exported to Europe and Asia. The granite is utilized in the fabrication of objects and in wall and floor covering. It is scientifically known because it presents natural series of radionuclides ( 238 U and 232 Th) and 40 K which are higher than the average content of the other rocks. The gamma radiation of the granite coming from the decay of the series cited accompanied by 40 K, must not exceed the limit of 1 mSv.a -1 for the public, according to norms that are in effect. The objective of this work is to evaluate the dose of gamma radiation that is absorbed by individuals who are exposed to the granite. This work is expected to contribute to environmental monitoring and to the evaluation of health risk to man. Pieces of granite from diverse environments were monitored for a total period of 225 days. Three batches of CaSO 4 :Dy were used. The first batch remained fixed to the pieces of granite (one dosimeter for each object) for period of sixty-eight days. After the reading, they were reaffixed to the same objects, each one of them accompanied by one or more dosimeters from the second and third batches. The dosimeters remained affixed for another average period of one hundred and forty-eight days. The absorbed doses found varied from the background up to 0.64 mSv.a -1 , with a general average of 0.24 mSv.a -1 , thus, it was concluded that the doses of granite studied, up to the present, were inside the parameters recommended by CNEN, when considering potentially exposed members of the public. (author)

Radiation dose to contra lateral breast during treatment of breast malignancy by radiotherapy

Directory of Open Access Journals (Sweden)

Chougule Arun

2007-01-01

Full Text Available Aims: External beam radiotherapy is being used regularly to treat the breast malignancy postoperatively. The contribution of collimator leakage and scatter radiation dose to contralateral breast is of concern because of high radio sensitivity of breast tissue for carcinogenesis. This becomes more important when the treated cancer breast patient is younger than 45 years and therefore the contralateral breast must be treated as organ at risk. Quantification of contralateral dose during primary breast irradiation is helpful to estimate the risk of radiation induced secondary breast malignancy. Materials and Methods: In present study contralateral breast dose was measured in 30 cancer breast patients undergoing external beam therapy by Co-60 teletherapy machine. Postoperative radiotherapy was delivered by medial and lateral tangential fields on alternate days in addition to supraclavicle field daily with 200 cGy/F to a total dose of 5000 cGy in 25 fractions. CaSO4: Dy themoluminescence dosimeter discs were employed for these measurements. Three TLD discs were put on the surface of skin of contra lateral breast, one at the level of nipple and two at 3 cms away from nipple on both side along the midline for each field. At the end treatment of each filed, TLD discs were removed and measured for dose after 24h on Thelmador - 6000 TLD reader. Results: The dose at the contra lateral breast nipple was to be 152.5 to 254.75 cGy for total primary breast dose of 5000 cGy in 25 equal fractions which amounted to 3.05-6.05% of total dose to diseased breast. Further it was observed that the maximum contribution of contralateral breast dose was due to medical tangential half blocked field. Conclusion: CaSO4; Dy thermoluminescence dosimetry is quite easy, accurate and convenient method to measure the contra lateral breast dose.

The ternary system K2SO4MgSO4CaSO4

Science.gov (United States)

Rowe, J.J.; Morey, G.W.; Silber, C.C.

1967-01-01

Melting and subsolidus relations in the system K2SO4MgSO4CaSO4 were studied using heating-cooling curves, differential thermal analysis, optics, X-ray diffraction at room and high temperatures and by quenching techniques. Previous investigators were unable to study the binary MgSO4CaSO4 system and the adjacent area in the ternary system because of the decomposition of MgSO4 and CaSO4 at high temperatures. This problem was partly overcome by a novel sealed-tube quenching method, by hydrothermal synthesis, and by long-time heating in the solidus. As a result of this study, we found: (1) a new compound, CaSO4??3MgSO4 (m.p. 1201??C) with a field extending into the ternary system; (2) a high temperature form of MgSO4 with a sluggishly reversible inversion. An X-ray diffraction pattern for this polymorphic form is given; (3) the inversion of ??-CaSO4 (anhydrite) to ??-CaSO4 at 1195??C, in agreement with grahmann; (1) (4) the melting point of MgSO4 is 1136??C and that of CaSO4 is 1462??C (using sealed tube methods to prevent decomposition of the sulphates); (5) calcium langbeinite (K2SO4??2CaSO4) is the only compound in the K2SO4CaSO4 binary system. This resolved discrepancies in the results of previous investigators; (6) a continuous solid solution series between congruently melting K2SOP4??2MgSO4 (langbeinite) and incongruently melting K2SO4??2CaSO4 (calcium langbeinite); (7) the liquidus in the ternary system consists of primary phase fields of K2SO4, MgSO4, CaSO4, langbeinite-calcium langbeinite solid solution, and CaSO4??3MgSO4. The CaSO4 field extends over a large portion of the system. Previously reported fields for the compounds (K2SO4??MgSO4??nCaSO4), K2SO4??3CaSO4 and K2SO4??CaSO4 were not found; (8) a minimum in the ternary system at: 740??C, 25% MgSO4, 6% CaSO4, 69% K2SO4; and ternary eutectics at 882??C, 49% MgSO4, 19% CaSO4, 32% K2SO4; and 880??, 67??5% MgSO4, 5% CaSO4, 27??5% K2SO4. ?? 1967.

Energy spectrum of CsDy(MoO/sub 4/)/sub 2/ in the vicinity of the structural phase transition

Energy Technology Data Exchange (ETDEWEB)

Khats' ko, E N; Chernyj, A S [AN Ukrainskoj SSR, Kharkov. Fiziko-Tekhnicheskij Inst. Nizkikh Temperatur

1981-08-01

The magnetic susceptibilities of CsDy(MoO/sub 4/)/sub 2/ and CsDy(MoO/sub 4/)/sub 2/+10%Eu/sup 3 +/ were measured in the temperature range 4 to 70 K and the frequency range 200 Hz to 20 MHz. The observed spin-lattice relaxation of the Dy/sup 3 +/ ion is found to be exponential with the relaxation time as a function of temperature tau/sup -1/=A exp (-..delta../kT) with ..delta..=105+-20 and 250+-40 cm/sup -1/ for CsDy(MoO/sub 4/)/sub 2/ in ranges 10-20 K and 20-38 K, respectively, and ..delta..=22.4+-5 cm for C=sDy(MoO/sub 4/)/sub 2/+10%Eu/sup 3 +/. The energies ..delta..105+-20 and 250 -40cm/sup -1/ are suggested to correspond to the first and second excited levels of Dy/sup 3 +/ in the low temperature phase of CsDy(MoO/sub 4/)/sub 2/, and ..delta..=22.4+-5 cm/sup -1/ to the first excited level of Dy/sup 3 +/ in the high temperature phase of the compound.

External dosimetry by Thermoluminescent Dosimetry Laboratory - IPEN/CNEN - Brazil

International Nuclear Information System (INIS)

Manzoli, Jose Eduardo; Carvalho, Ricardo Nunes

2001-01-01

The Thermoluminescence Dosimetry Laboratory, LDT - IPEN/CNEN - Brazil, executes around six thousand TLD readings monthly. It is responsible for the dose evaluation and registration and for all the manufacture process of preparation and sending the dosemeters which are used by IPEN itself, hospitals, industries, town halls, universities, etc. Although prepared to read many kinds of materials, actually the LDT reads only CaSO 4 :Dy detector chips. Chips, heating molds, plastic packaging and almost every material or instrument are made right here at IPEN. The readings are performed in a Bicron Harshaw TLD model 5500, but an old model 2000-AB is ready to be used if necessary. In this work it is presented some features of this important service realized to the IPEN workers and to the community. (author)

[Effect of charge compensation on emission spectrum of Sr2SiO4 : Dy3+ phosphor].

Science.gov (United States)

Li, Pan-Lai; Wang, Zhi-Jun; Yang, Zhi-Ping; Guo, Qing-Lin

2009-01-01

The Sr2SiO4 : Dy3+ phosphor was synthesized by the high temperature solid-state reaction method in air. Dy2O3 (99.9%), SiO2 (99.9%), SrCO3 (99.9%), Li2CO3 (99.9%), Na2CO3 (99.9%) and K2CO3 (99.9%) were used as starting materials, and the Dy3+ doping concentration was 2 mol%. The emission spectrum was measured by a SPEX1404 spectrophotometer, and all the characterization of the phosphors was conducted at room temperature. The emission spectrum of Sr2 SiO4 : Dy3+ phosphor showed several bands centered at 486, 575 and 665 nm under the 365 nm excitation. The effect of Li+, Na+ and K+ on the emission spectra of Sr2SiO4 : Dy3+ phosphor was studied. The results show that the location of the emission spectrum of Sr2SiO4 : Dy3+ phosphor was not influenced by Li+, Na+ and K+. However, the emission spectrum intensity was greatly influenced by Li+, Na+ and K+, and the evolvement trend was monotone with different charge compensation, i. e. the emission spectrum intensity of Sr2SiO4 : Dy3+ phosphor firstly increased with increasing Li+ concentration, then decreased. However the charge compensation concentration corresponding to the maximum emission intensity was different with different charge compensation, and the concentration is 4, 3 and 3 mol% corresponding to Li+, Na+ and K+, respectively. And the theoretical reason for the above results was analyzed.

High energy electron beams characterization using CaSO{sub 4}:Dy+PTFE Phosphors for clinical therapy applications

Energy Technology Data Exchange (ETDEWEB)

Rivera, T., E-mail: trivera@ipn.mx [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada-Legaria, IPN. Av. Legaria 694, Col. Irrigacion. 11500 Mexico DF (Mexico); Espinoza, A.; Von, S.M. [Centro Estatal de Cancerologia de los Servicios de Salud de Nayarit, Enfermeria S/n, Fracc, Fray Junipero Serra, 63169 Tepic Nay (Mexico); Alvarez, R.; Jimenez, Y. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada-Legaria, IPN. Av. Legaria 694, Col. Irrigacion. 11500 Mexico DF (Mexico)

2012-07-15

In the present work high energy electron beam dosimetry from linear accelerator (LINACs) for clinical applications using dysprosium doped calcium sulfate embedded in polytetrafluorethylene (CaSO{sub 4}:Dy+PTFE) was studied. The irradiations were carried out using high electron beams (6 to 18 MeV) from a linear accelerator (LINAC) Varian, CLINAC 2300C/D, for clinical practice purpose. The electron irradiations were obtained using the water solid in order to guarantee electronic equilibrium conditions (EEC). Field shaping for electron beams was obtained with electron cones. Glow curve and other thermoluminescent characteristics of CaSO{sub 4}:Dy+PTFE were conducted under high electrons beams irradiations. The TL response of the pellets showed an intensity peak centered at around 215 Degree-Sign C. TL response of CaSO{sub 4}:Dy+PTFE as a function of high electron absorbed dose showed a linearity in a wide range. To obtain reproducibility characteristic, a set of pellets were exposed repeatedly for the same electron absorbed dose. The results obtained in this study can suggest the applicability of CaSO{sub 4}:Dy+PTFE pellets for high electron beam dosimetry, provided fading is correctly accounted for. - Highlights: Black-Right-Pointing-Pointer Developing of CaSO{sub 4}:Dy to electron beams dosimetry. Black-Right-Pointing-Pointer Characterization of caSO{sub 4}:Dy to radiation safety in LINACs. Black-Right-Pointing-Pointer TL characteristics of CaSO{sub 4}:Dy for electron beams quality control.

YVO{sub 4}:Eu{sup 3+}, Dy{sup 3+}-Fe{sub 3}O{sub 4} co-doped nanocomposites: preparation, luminescent, and magnetic properties

Energy Technology Data Exchange (ETDEWEB)

Liu Deming; Shi Jianhui; Tong Lizhu; Ren Xiaozhen; Li Quanhong; Yang Hua, E-mail: huayang86@sina.com [Jilin University, College of Chemistry (China)

2012-11-15

A series of different concentrations of Eu{sup 3+} and Dy{sup 3+} ions co-doping yttrium vanadate phosphors coated with Fe{sub 3}O{sub 4} (YVO{sub 4}:Eu{sup 3+}, Dy{sup 3+}-Fe{sub 3}O{sub 4}) was successful prepared by using two steps route including sol-gel method and hydrothermal method. The resulting phase formation, particle morphology, structure, luminescent, and magnetic properties were examined by X-ray diffraction, transmission electron microscopy, photoluminescence spectra, and vibrating sample magnetometer. The results indicate that the diameter of the YVO{sub 4}:Eu{sup 3+}, Dy{sup 3+}-Fe{sub 3}O{sub 4} nanocomposites is 100-300 nm. The special saturation magnetization Ms of the nanocomposites is 53 emu/g. Additionally, the emission intensities of YVO{sub 4}:Eu{sup 3+} or Dy{sup 3+} ions are regularly changed with the emission doping concentrations. After coating with Fe{sub 3}O{sub 4}, the variation of the luminescent intensity of YVO{sub 4}:Eu{sup 3+}, Dy{sup 3+}-Fe{sub 3}O{sub 4} magnetic phosphors is different.

Thermoluminescent characteristics of CaSO{sub 4}:Dy+PTFE irradiated with high energy electron beams; Caracteristicas termoluminiscentes del CaSO{sub 4}:Dy+PTFE irradiado con haces de electrones de alta energia

Energy Technology Data Exchange (ETDEWEB)

Alvarez, R.; Rivera, T.; Calderon, J. A.; Jimenez, Y. [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Av. Legaria 694, Col. Irrigacion, 11500 Mexico D. F. (Mexico); Rodriguez, J. [Hospital General de Mexico, Dr. Balmis 148, Col. Doctores, 06726 Mexico D. F. (Mexico); Oviedo, O. [Centro Medico ABC, Sur 136 No. 116, Col. Las Americas, 01120 Mexico D. F. (Mexico); Azorin, J., E-mail: chagua@hotmail.com [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Av. San Rafael Atlixco 186, 09340 Mexico D. F. (Mexico)

2011-10-15

In the present work thermoluminescent response of dysprosium doped calcium sulfate embedded in polytetrafluorethylene (CaSO{sub 4}:Dy+PTFE) under high electron beam irradiations from linear accelerator for clinical applications was investigated. The irradiations were carried out using high electron beams (6 to 18 MeV) from a linear accelerator Varian, C linac 2300C/D, for clinical practice purpose. The electron irradiations were obtained by using the water solid in order to guarantee electronic equilibrium conditions. Field shaping for electron beams was obtained with electron cones. Glow curve and other thermoluminescent characteristics of CaSO{sub 4}:Dy+PTFE were conducted under high electron beams irradiations. The thermoluminescent response of the pellets showed and intensity peak centered at around 235 C. Thermoluminescent response of CaSO{sub 4}:Dy+PTFE as a function of high electron absorbed dose showed a linearity in a wide range. To obtain reproducibility characteristic, a set of pellets were exposed repeatedly for the same electron absorbed dose. The results obtained in this study can suggest the applicability of CaSO{sub 4}:Dy+PTFE pellets for high electron beam dosimetry, provided fading is correctly accounted for. (Author)

Scattered radiation dose to radiologist's cornea, thyroid and gonads while performing some x-ray fluoroscopic investigations

International Nuclear Information System (INIS)

Chougle, Arun

1993-01-01

The mankind has been immensely benefited from discovery of X-ray and it has found wide spread application in diagnosis and treatment. Radiation is harmful and can produce somatic and genetic effects in the exposed person. International Commission on Radiation Protection (ICRP) has recommended a system of dose limitation based on principle of ALARA. All the efforts should be made to keep the radiation dose to the radiation worker as low as possible. Fluoroscopy gives maximum dose to the patient and staff and hence we have attempted to quantify the scattered radiation dose to the cornea, thyroid and gonads of the radiologist performing fluoroscopic examinations such as barium meal, barium swallow, barium enema, myelography, histerosalpingography and fracture reduction. Thermoluminescence dosimetry (TLD) method using CaSO 4 :Dy TLD disc was employed for these measurements. Use of lead apron has reduced the dose to radiologist's gonad. (author). 3 refs., 4 tabs

Magnetic moments of high spin rotational states in 158Dy and 164Dy+

International Nuclear Information System (INIS)

Seiler-Clark, G.

1983-09-01

For the study of their magnetic moments yrast states in 158 Dy and 164 Dy were excited via the multiple-Coulomb excitation by a 4.7 MeV/u 208 Pb beam. Hereby especially the question was of interest, how the one-particle effects in the nuclear structure in the region of the backbending anomaly in 158 Dy take effects on the g-factors of the high spin states in this region. The particle-γ angular correlations perturbed in the transient magnetic field during the passing of the excited Dy ions through a thin magnetized iron foil were measured. By the selective position-sensitive detection of Dy recoil ions and Pb projectiles under forward angles it was possible to determine additionally to the g-factors in the backbending region also g-factors in the spin region I 158 Dy and 164 Dy by detection of the particle-γ correlations precessing in the static hyperfine field after implantation in iron. The static hyperfine field was at the 4 + state in 164 Dy determined to B (Dy,Fe) = 245+-25 T. The g-factors were determined by comparison of the experimental results with calculations of the perturbed angular correlations by time-differential regarding of the population and de-excitation of the yrast states as well as by precession and hyperfine-relaxation effects during the flight of the Dy ions in the vacuum. (orig./HSI) [de

Facile synthesis, structural characterization, and photoluminescence mechanism of Dy{sup 3+} doped YVO{sub 4} and Ca{sup 2+} co-doped YVO{sub 4}:Dy{sup 3+} nano-lattices

Energy Technology Data Exchange (ETDEWEB)

Dhiren Meetei, Sanoujam, E-mail: sdmdhiren@gmail.com; Dorendrajit Singh, Shougaijam, E-mail: dorendrajit@yahoo.co.in, E-mail: mdebensingh@gmail.com [Department of Physics, Manipur University, Canchipur, Imphal-795003, Manipur (India); Deben Singh, Mutum, E-mail: dorendrajit@yahoo.co.in, E-mail: mdebensingh@gmail.com [Department of Physics, Thambal Marik College, Oinam-795134, Bishnupur, Manipur (India)

2014-05-28

Light plays a vital role in the evolution of life. From sunlight to candle-light and then to other form of lighting devices, human beings are utilizing light since time immemorial. Lighting devices such as conventional incandescent lamp and fluorescent lamp have been replaced by Light Emitting Diodes (LEDs) for the later is cheap, durable, etc. Now-a-days, phosphor converted LEDs have been burning issues in the fabrication of lighting devices. Especially, lanthanide ion(s) doped phosphors are of great interest for the same. However, doped phosphors have a limitation of luminescence quenching, i.e., instead of increasing luminescence on increasing dopant concentration, the luminescence decreases. Therefore, it must be rectified by one or other means so as to get maximum desirable intensity for uses in display or lighting devices. In the present work, YVO{sub 4}:Dy{sup 3+} and YVO{sub 4}:Dy{sup 3+}/Ca{sup 2+} nano-lattices are synthesized by a facile technique. Structural characterizations such as x-ray diffraction, SEM, TEM, HRTEM, and Selected Area Electron Diffraction (SAED) of the samples are reported. Photoluminescence (PL) excitation and emission, enhanced mechanism, and lifetime are thoroughly discussed. PL intensity of the quenched YVO{sub 4}:Dy{sup 3+} is made increased up to 432.63% by Ca{sup 2+} co-doping. Role of the Ca{sup 2+} on the luminescence enhanced mechanism of YVO{sub 4}:Dy{sup 3+}/Ca{sup 2+} is elucidated.

Construction of pulse badge for upper extremities dosimetry in nuclear medicine

International Nuclear Information System (INIS)

Cunha, Cledison de Jesus; Souza, Divanizia do Nascimento

2005-01-01

In the manipulation of radioactive materials in nuclear medicine service the body parts of the worker who more is displayed to the ionizing radiation is hands, forearm and arm. Therefore it is necessary to developing badges for easy reproduction monitoring and low cost to determine the doses level radiation received by the worker in these extremities. The aim of this work is to investigation of a new pulse badge, that is developed with thermoluminescent detectors of CaSO 4 :Dy (TLD) in a small plate of acrylic, perforated cardboard to deposit the TLD. This set was involved in plastic to protect of humidity and other harmful ambient factors, moreover, a bracelet was inserted, adaptable for any worker. This badge had been gotten resulted satisfactory, with a reply to the enough dose for a dosimetric evaluation. (author)

Analysis of glow curves of TL readouts of CaSO4:Dy teflon based TLD badge in semiautomatic TLD badge reader

International Nuclear Information System (INIS)

Pradhan, S.M.; Sneha, C.; Adtani, M.M.

2010-01-01

The facility of glow curve storage and recall provided in the reader software is helpful for manual screening of the glow curves; however no further analysis is possible due to absence of numerical TL data at the sampling intervals. In the present study glow curves are digitized by modifying the reader software and then normalized to make them independent of the dose. The normalized glow curves are then analyzed by dividing them into five equal parts on time scale. This method of analysis is used to correlate the variation of total TL counts of the three discs with time elapsed post irradiation

A TLD reader for wide range in situ dose measurement

International Nuclear Information System (INIS)

Deme, S; Apathy, I.; Bodnar, L.; Csoeke, A.; Hejja, I.

1998-01-01

A portable thermoluminescent dosemeter reader suitable for reading at the site of exposure is described. The instrument consists of a glass bulb containing the CaSO 4 :Dy thermoluminescent material laminated to the surface of an electrically heated resistive metal plate. The bulb is encapsulated in a cylindrical, pen-like metal holder made of aluminium. A one-wire-port integrated electronic programmable memory chip mounted inside the holder contains the identification code and the individual calibration parameters of the dosemeter. The aperture of the holder is normally covered by a stainless steel tube to protect the bulb from light and mechanical shocks. The tube slips backwards automatically when the dosemeter is inserted into the reader. The system is used by the Hungarian nuclear power plant. (M.D.)

Tunable photoluminescence and magnetic properties of Dy(3+) and Eu(3+) doped GdVO4 multifunctional phosphors.

Science.gov (United States)

Liu, Yanxia; Liu, Guixia; Dong, Xiangting; Wang, Jinxian; Yu, Wensheng

2015-10-28

A series of Dy(3+) or/and Eu(3+) doped GdVO4 phosphors were successfully prepared by a simple hydrothermal method and characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectrometry (EDS), photoluminescence (PL) spectroscopy and vibrating sample magnetometry (VSM). The results indicate that the as-prepared samples are pure tetragonal phase GdVO4, taking on nanoparticles with an average size of 45 nm. Under ultraviolet (UV) light excitation, the individual Dy(3+) or Eu(3+) ion activated GdVO4 phosphors exhibit excellent emission properties in their respective regions. The mechanism of energy transfer from the VO4(3-) group and the charge transfer band (CTB) to Dy(3+) and Eu(3+) ions is proposed. Color-tunable emissions in GdVO4:Dy(3+),Eu(3+) phosphors are realized through adopting different excitation wavelengths or adjusting the appropriate concentration of Dy(3+) and Eu(3+) when excited by a single excitation wavelength. In addition, the as-prepared samples show paramagnetic properties at room temperature. This kind of multifunctional color-tunable phosphor has great potential applications in the fields of photoelectronic devices and biomedical sciences.

New intermetallic compounds Ln(Ag, AL)4 (Ln-Y, Gd, Tb, Dy) and their structure

International Nuclear Information System (INIS)

Kuz'ma, Yu.B.; Stel'makhovich, B.M.

1990-01-01

By the methods of X-ray analysis crystal structure of compounds Ln(Ag,Al) 4 , where Ln-Y, Gd, Tb, Dy, posessing rhombic structure, is determined. The intermetallics have been prepared for the first time. Ways of atom distribution and their coordinates in DyAg 0.55 Al 3.45 structure (a=0.4296(1), b=04179(1), c=0.9995(3), R=0.093) are specified. Other compounds are formed in case of LnAgAl 3 compositions. Interatomic distances in Dy(Ag,Al) 4 structure are considered. A supposition is made on the formation in Ln-Ag-Al systems of a greater number of intermetallic compounds

Antiferroquadrupolar ordering and anisotropic magnetic phase diagram of dysprosium palladium bronze, DyPd3S4

International Nuclear Information System (INIS)

Matsuoka, Eiichi; Tayama, Takashi; Sakakibara, Toshiro; Hiroi, Zenji; Takeda, Naoya; Ishikawa, Masayasu; Shirakawa, Naoki

2007-01-01

From the measurements of magnetization and specific heat, we constructed B-T phase diagrams of single-crystalline DyPd 3 S 4 which is known to exhibit antiferroquadrupolar (AFQ) and antiferromagnetic (AFM) ordering at low temperatures. The phase diagrams are found to be highly anisotropic and re-entrant, which are typical of rare-earth compounds exhibiting multipolar ordering. The crystalline electric field (CEF) scheme of Dy 3+ in DyPd 3S4 was deduced from the specific heat and magnetization measurements of the Y-diluted compounds Dy 1-x Y x Pd 3 S 4 (0.1≤x≤0.9) and discussed in detail. The CEF ground state was determined to be the orbitally-degenerated quartet Γ 67 (1) , and the overall splitting width was estimated to be about 104 K. No correlation was found between the anisotropy of T Q and that of the Zeeman splitting width of the ground quartet Γ 67 (1) . (author)

The minimum measurable dose of CaF{sub 2}:Dy measured via an improved heating profile with an automatic 6600 thermoluminescent detector

Energy Technology Data Exchange (ETDEWEB)

Ben-Shachar, B; Weinstein, M; German, U [Israel Atomic Energy Commission, Beersheba (Israel). Nuclear Research Center-Negev

1996-12-01

One of the advantages of the thermoluminescent method is its ability to measure low doses, which is useful in environmental dosimetry, as well as in archaeology. The CaF{sub 2}:Dy (Crown as TLD-200), has a sensitivity of 10-30 times greater than the sensitivity of TLD-100, when irradiated by Cs-137. In the present work we evaluated the TL-dose response of CaF{sub 2}:Dy, by using an improved heating profile which is giving the main glow peak alone. The relative standard deviations were fitted to a semiempirical expression, from which the minimum measurable doses (MMD) were derived. The MMD were calculated by taking 3 times the standard deviation of the unirradiated chips. The results of the TL-dose response, as well as file fee calculated MMD by taxing 3 times the standard deviation of unirradiated chips, measured by file new 6600 automatic thermoluminescent detector, are presented in this work. We received a MMD of about 0.01 mGy (1 mrad), an improvement of a factor of 2.5 relatively to the integral light response evaluation using the standard heating profile (authors).

Thermoluminescence fast neutron dosimetry by laser heating

International Nuclear Information System (INIS)

Mathur, V.K.; Brown, M.D.; Braeunlich, P.

1984-01-01

Heating rates in excess of 10 4 K.sec -1 have been achieved for thin layers of TL dosemeters by laser heating. The high heating rate improves the signal to noise ratio up to a factor of 10 3 . Thus sensitive thin film fast neutron dosemeters with negligible self-shielding have become a practical reality. Thin samples of CaSO 4 :Dy have been investigated for their response to fast neutrons from a Pu-Be source and a 14.6 MeV neutron generator by using a hydrogenous radiator. A 15 watt CO 2 laser was focussed on the thin TLD layer to a spot size of less than 1 mm to heat it. An exposure of a few tens of milliseconds was sufficient to obtain a TLD curve, which was displayed and processed by a wave form digitiser. The laser spot could be scanned over the TLD sample by a x-y positioner and a large number of observations were obtained on each sample. Preliminary results show that it is possible to obtain a figure of merit of approx. 5% in a mixed n, γ field. A practical design for a fast neutron dosemeter is proposed. (author)

Investigation of the thermoluminescent response of K2GdF5:Dy3+ crystals to photon radiation and neutron fields

International Nuclear Information System (INIS)

Silva, Edna C.; Faria, Luiz O.; Santos, Joelan A.L.; Vilela, Eudice C.

2009-01-01

The thermoluminescent (TL) properties of undoped and Dy 3+ doped K 2 GdF 5 crystals were investigated from the point of view of gamma and neutron dosimetry. Crystalline K 2 GdF 5 platelets with thickness of about 1 mm and doped with 0.0, 0.2, 1.0, 5.0 and 10.0 at.% Dy 3+ ions, synthesized under hydrothermal conditions, were irradiated in order to study TL sensitivity, as well as dose and energy response, reproducibility and fading. As it has been turned out, crystals doped with 5.0 at% Dy 3+ show the most efficient TL response and demonstrate a linear response to doses for all the radiation fields. TL glow curves from Dy 3+ doped K 2 GdF 5 crystals can be deconvoluted into four individual TL peaks centered at 153, 185, 216 and 234 deg C. Concerning the photon fields studied, the maximum TL response has been found for the 52.5 keV photons. The intensity is 15 times more than that of the response for the 662 keV photons from a Cs-137 source. On the other hand, the K 2 GdF 5 crystals doped with 5.0 at % Dy 3+ have also been found to have the better TL response for fast neutron radiation, among all dopants studied. For fast neutron radiation produced by a 241 Am-Be source, the TL responses for doses were also linear and comparable to that of commercial TLD-600, irradiated at same conditions. It has been established that the gamma sensitivity of the crystals is about 0.07% of the neutron sensitivity and the fast neutron sensitivity is about 4.5 % of the thermal neutron sensitivity. These results points out that K 2 Gd 0.95 Dy 0.05 F 5 crystals are good candidates for use in neutron dosimetry applications. (author)

Ultraviolet dosimetry using thermoluminescent phosphors - an update

International Nuclear Information System (INIS)

Nagpal, J.S.

1998-04-01

Intrinsic response of various thermoluminescent (TL) materials such as CaSO 4 (Dy, Eu, Mn, Sm, Tb, or Tm), LiF (Mg, Cu, P), Mg 2 SiO 4 :Tb, CaF 2 :Dy, CaF 2 :Tb, ThO 2 :Tb and Al 2 O 3 (Si, Ti); cathodoluminescent phosphors Y 3 Al 5 O 12 :Ce, Y 3 Al 5 O 12 :Tb and Y(V,P)O 4 :Eu; and fluorescent lamp phosphors calcium halophosphate (Mn,Sb) and Ce Mg aluminate (Eu, Tb) to ultraviolet (UV) radiations has been studied. Intrinsic TL response of most of the phosphors is rate (radiant flux) dependent. For the first time, UV response of the materials is reported for a fixed total radiant energy (total UV dose), at a single radiant flux (260 μW.cm -2 ), for an appropriate comparison. A wide range of UV sensitivity is observed. Studies conducted using UV radiation from two unfiltered low pressure mercury lamps show significant differences in glow curves, as compared to those obtained with nearly monochromatic UV radiations. Photons of wavelength 365 nm induce bleaching of TL induced by 254 nm photons, in most of the materials. Sequential/tandem exposures to 254 nm and 365 nm photons have yielded new but alarming results in CaF 2 :Tb. Preferential induction and bleaching of specific TL glow peaks by 365 nm and 254 nm photons are interesting characteristics discovered in CaSO 4 :Eu. Photoluminescence studies of Tb 3+ and Eu 3+ activated phosphors have augmented the inferences drawn from the bleaching effects produced by 365 nm photons. Earlier work carried out on phototransferred thermoluminescence of CaSO 4 :Dy-teflon dosimeters, TLD-100, Mg 2 SiO 4 :Tb and Al 2 O 3 (Si,Ti) has also been reviewed. (author)

Giant magnetocaloric effect in antiferromagnetic DyVO{sub 4} compound

Energy Technology Data Exchange (ETDEWEB)

Midya, A., E-mail: arindam.midya@saha.ac.in; Khan, N.; Bhoi, D.; Mandal, P.

2014-09-01

We have investigated the magnetic and magnetocaloric properties of DyVO{sub 4} by magnetization and heat capacity measurements. χ(T) shows antiferromagnetic to paramagnetic transition at T{sub N}{sup Dy}∼3.5K. The compound undergoes a metamagnetic transition and exhibits a huge entropy change. The maximum values of magnetic entropy change (ΔS{sub M}), adiabatic temperature change (ΔT{sub ad}) and refrigerant capacity (RC) reach 26 J kg{sup −1} K{sup −1}, 17 K, and 526 J kg{sup −1}, respectively for a field change of 0–8 T. Moreover, the material is highly insulating and exhibits no thermal and field hysteresis, satisfying the necessary conditions for a good magnetic refrigerant material.

TLD array for precise dose measurements in stereotactic radiation techniques

International Nuclear Information System (INIS)

Ertl, A.; Kitz, K.; Griffitt, W.; Hartl, R.F.E.; Zehetmayer, M.

1996-01-01

We developed a new TLD array for precise dose measurement and verification of the spatial dose distribution in small radiation targets. It consists of a hemicylindrical, tissue-equivalent rod made of polystyrene with 17 parallel moulds for an exact positioning of each TLD. The spatial resolution of the TLD array was evaluated using the Leskell spherical phantom. Dose planning was performed with KULA 4.4 under stereotactic conditions on axial CT images. In the Leksell gamma unit the TLD array was irradiated with a maximal dose of 10 Gy with an unplugged 14 mm collimator. The doses delivered to the TLDs were rechecked by diode detector and film dosimetry and compared to the computer-generated dose profile. We found excellent agreement of our measured values, even at the critical penumbra decline. For the 14 mm and 18 mm collimator and for the 11 mm collimator combination we compared the measured and calculated data at full width at half maximum. This TLD array may be useful for phantom or tissue model studies on the spatial dose distribution in confined radiation targets as used in stereotactic radiotherapy. (author)

Neutron and photon dose assessment in Indus accelerator complex

International Nuclear Information System (INIS)

Verma, Dimple; Haridas Nair, G.; Bandopadhyay, Tapas; Tripathy, R.M.; Pal, Rupali; Bakshi, A.K.; Palani Selvam, T.; Datta, D.

2016-02-01

Indus Accelerator Complex (IAC) consists of 20 MeV Microtron, 450/550 MeV Booster, 450 MeV Indus-1 and 2.5 GeV Indus-2 storage rings. The radiation environment in Indus Accelerator Complex comprises of bremsstrahlung photons, electrons, positrons, photo neutrons and muons, out of which, bremsstrahlung photons are the major constituent of the prompt radiation. Major problem faced for on-line detection of neutrons is their severely pulsed nature. In the present study, measurement of neutron and photon dose rates in Indus Accelerator Complex was carried out using passive dosimeters such as CR-39 solid state nuclear track detector (SSNTD) and CaSO 4 :Dy Teflon disc, 6 LiF:Mg,Ti (TLD 600) and 7 LiF:Mg,Ti (TLD 700) based thermo luminescent (TL) detectors. The report describes the details of the measurement and discusses the results. (author)

Robust determination of effective atomic numbers for electron interactions with TLD-100 and TLD-100H thermoluminescent dosimeters

International Nuclear Information System (INIS)

Taylor, M.L.

2011-01-01

Lithium fluoride thermoluminescent dosimeters (TLD) are the most commonly implemented for clinical dosimetry. The small physical magnitude of TLDs makes them attractive for applications such as small field measurement, in vivo dosimetry and measurement of out-of-field doses to critical structures. The most broadly used TLD is TLD-100 (LiF:Mg,Ti) and, for applications requiring higher sensitivity to low-doses, TLD-100H (LiF:Mg,Cu,P) is frequently employed. The radiological properties of these TLDs are therefore of significant interest. For the first time, in this study effective atomic numbers for radiative, collisional and total electron interaction processes are calculated for TLD-100 and TLD-100H dosimeters over the energy range 1 keV-100 MeV. This is undertaken using a robust, energy-dependent method of calculation rather than typical power-law approximations. The influence of dopant concentrations and unwanted impurities is also investigated. The two TLDs exhibit similar effective atomic numbers, ranging from approximately 5.77-6.51. Differences arising from the different dopants are most pronounced in low-energy radiative effects. The TLDs have atomic numbers approximately 1.48-2.06 times that of water. The effective atomic number of TLD-100H is consistently higher than that of TLD-100 over a broad energy range, due to the greater influence of the higher-Z dopants on the electron interaction cross sections. Typical variation in dopant concentration does not significantly influence the effective atomic number. The influence on TLD-100H is comparatively more pronounced than that on TLD-100. Contrariwise, unwanted hydroxide impurities influence TLD-100 more than TLD-100H. The effective atomic number is a key parameter that influences the radiological properties and energy response of TLDs. Although many properties of these TLDs have been studied rigorously, as yet there has been no investigation of their effective atomic numbers for electron interactions. The

Energy transfer and colorimetric properties of Eu3+/Dy3+ co-doped Gd2(MoO4)3 phosphors

International Nuclear Information System (INIS)

Wan Jing; Cheng Lihong; Sun Jiashi; Zhong Haiyang; Li Xiangping; Lu Weili; Tian Yue; Lin Hai; Chen Baojiu

2010-01-01

Dy 3+ single-doped and Eu 3+ /Dy 3+ co-doped gadolinium molybdate (Gd 2 (MoO 4 ) 3 ) phosphors were synthesized by a traditional solid-state reaction method. The XRD was used to confirm the crystal structure of the phosphors. The energy transfer between Eu 3+ and Dy 3+ was observed and studied. The Eu 3+ concentration can hardly affect the blue and yellow emission intensities of Dy 3+ , and the Eu 3+ emission intensity increases with the increase of Eu 3+ concentration. Co-doping with Eu 3+ compensated the red emission component of the Dy 3+ doped Gd 2 (MoO 4 ) 3 phosphor. Introducing proper amount of Eu 3+ can improve the colorimetric performance of the phosphors.

Concentration-dependent luminescence and energy transfer of flower-like Y2(MoO4)3:Dy3+ phosphor

International Nuclear Information System (INIS)

Tian Yue; Chen Baojiu; Tian Bining; Hua Ruinian; Sun Jiashi; Cheng Lihong; Zhong Haiyang; Li Xiangping; Zhang Jinsu; Zheng Yanfeng; Yu Tingting; Huang Libo; Meng Qingyu

2011-01-01

Highlights: → Flower-shaped Y 2 (MoO 4 ) 3 phosphors were prepared by a co-precipitation method. → The structure and morphology of the prepared phosphors were characterized. → Energy transfer between Dy 3+ was studied by Huang's theory, IH and Uitert's models. - Abstract: Flower-like Y 2 (MoO 4 ) 3 :Dy 3+ phosphors have been synthesized via a co-precipitation approach with the aid of β-cyclodextrin. The crystal structure and morphology of the phosphors were characterized by XRD (X-ray diffraction) and FE-SEM (field emission scanning electron microscopy), respectively. The excitation and emission properties of the phosphors were examined by fluorescence spectroscopy. The dependence of color coordinates on the Dy 3+ doping concentration was analyzed. The energy transfer mechanism between Dy 3+ ions was studied based on the Huang's theory, I-H and Van Uitert's models. It was concluded simultaneously from these three routes that the electric dipole-dipole interaction between Dy 3+ ions is the main physical mechanism for the energy transfers between Dy 3+ .

Calculations of the magnetic entropy change in amorphous through a microscopic anisotropic model: Applications to Dy{sub 70}Zr{sub 30} and DyCo{sub 3.4} alloys

Energy Technology Data Exchange (ETDEWEB)

Ranke, P. J. von, E-mail: von.ranke@uol.com.br; Nóbrega, E. P.; Ribeiro, P. O.; Alvarenga, T. S. T.; Lopes, P. H. O.; Sousa, V. S. R. de; Oliveira, N. A. de [Instituto de Física, Universidade do Estado do Rio de Janeiro—UERJ, Rua São Francisco Xavier, 524, 20550-013 Rio de Janeiro (Brazil); Caldas, A. [Sociedade Unificada de Ensino Superior e Cultura, SUESC, 20211-351 Rio de Janeiro (Brazil); Alho, B. P. [Instituto de Aplicação Fernando Rodrigues da Silveira, Universidade do Estado do Rio de Janeiro, Rua Santa Alexandrina, 288, 20260-232 Rio de Janeiro (Brazil); Carvalho, G. [Laboratório Nacional de Luz Sincroton—LNLS, 13083-970 Campinas, São Paulo (Brazil); Magnus, A.

2014-10-14

We report theoretical investigations on the magnetocaloric effect, described by the magnetic entropy change in rare earth—transition metal amorphous systems. The model includes the local anisotropy on the rare earth ions in Harris-Plischke-Zuckermann assumptions. The transition metals ions are treated in terms of itinerant electron ferromagnetism and the magnetic moment of rare earth ions is coupled to the polarized d-band by a local exchange interaction. The magnetocaloric effect was calculated in DyCo{sub 3.4} system, which presents amorphous sperimagnetic configuration. The calculations predict higher refrigerant capacity in the amorphous DyCo{sub 3.4} than in DyCo{sub 2} crystal, highlighting the importance of amorphous magnetocaloric materials. Our calculation of the magnetocaloric effect in Dy{sub 70}Zr{sub 30}, which presents amorphous asperomagnetic configuration, is in good agreement with the experimental result. Furthermore, magnetic entropy changes associated with crystal-amorphous configurations change are estimated.

On the phototransferred thermoluminescence in MgB4O7:Dy

International Nuclear Information System (INIS)

Richmond, R.G.

1987-01-01

On exposure to ionizing radiations, the normal traps in MgB 4 0 7 :Dy can be emptied by the readout process only or by annealing at suitable temperatures, leaving the deep traps still intact. Subsequently, it is possible to repopulate the dosimetric peak by illuminating with u.v. light. Charge carriers released from the traps during the second readout give rise to a thermoluminescent output proportional to the ionizing radiation exposure and the u.v. radiant energy. This is called phototransferred thermoluminescence (PTTL). The PTTL method can be utilized for the reassessment of the initial γ-ray exposure. This paper presents the measurements of the intrinsic response of the commercially available MgB 4 0 7 :Dy to u.v. radiation, with a demonstration of its use for γ-ray dose re-estimation using the PTTL technique. (author)

Solvent directed morphologies and enhanced luminescent properties of BaWO4:Tm3+,Dy3+ for white light emitting diodes

Science.gov (United States)

Wu, Hongyue; Yang, Junfeng; Wang, Xiaoxue; Gan, Shucai; Li, Linlin

2018-05-01

A series of Tm3+ and Dy3+ codoped BaWO4 phosphors with tunable shapes were controllably synthesized by a facile solvothermal method. The effects of ratio of ethylene glycol (EG) and water on the morphologies of BaWO4 structures are systematically studied. It was discovered that the reason for these morphological changes is based on the reaction speed of the kinetic control, which relates to the strong chelating abilities of ethylene glycol. And when the solvent is pure ethylene glycol, the peanut-like BaWO4:Dy3+ has the strongest emission intensity. Moreover, the emission color of the phosphors varied from blue (0.232, 0.180) to white (0.268, 0.250) by controlling Dy3+ ions content with a fixed Tm3+ concentration. The energy transfer mechanism was investigated in detail. With increasing the doped concentration of Dy3+ ions, the energy transfer efficiency of BaWO4:0.005Tm3+,yDy3+ increased gradually and reached as high as 63% when the Dy3+ doped concentration is 0.03. The critical distance RC calculated by the spectral overlap method is about 19.93 Å, and it is in good agreement with that obtained using the concentration quenching method (19.70 Å), indicating that the electric dipole-dipole interaction is the main energy transfer mechanism for BaWO4:Tm3+,Dy3+ phosphors.

Mechanoluminescence of Dy doped strontium aluminate nanophosphors

Energy Technology Data Exchange (ETDEWEB)

Sharma, Ravi, E-mail: rvsharma65@gmail.com [Department of Physics, Govt. Arts and Commerce Girls College, Raipur, C.G. 492001 (India); Bisen, D.P. [School of Studies in Physics and Astrophysics, Pt. Ravishankar Shukla University, Raipur, C.G. 492010 (India); Chandra, B.P. [Department of Postgraduate Studies and Research in Physics and Electronics, Rani Durgavati University, Jabalpur 482001 (India)

2015-12-15

Nanosized strontium aluminate phosphors activated with Dy{sup 3+} were prepared by a combustion method. Nanophosphor was prepared by this method at reaction temperatures as low as 600 °C. Powder X-ray diffraction (XRD), scanning electron microscope analysis was used to characterize the prepared product. The monoclinic phase was observed in the XRD pattern. The particle size of the samples was calculated around 35 nm. The SEM images show irregular shape of the prepared nanophosphor. Two peaks were found in the mechanoluminescence (ML) response curve plotted between time and ML intensity. The H{sub 3}BO{sub 3} added strontium aluminate phosphors activated with Dy show more bright ML peak as compared to the powders of SrAl{sub 2}O{sub 4}:Dy{sup 3+} without H{sub 3}BO{sub 3.} It was found that the PL and ML intensity increases with increasing concentration of Dy, it becomes maximum for 3% of Dy. The photoluminescence emission shows two intense fluorescence transitions peaks at 498 nm and 583 nm, {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} in the blue and {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} in the yellow-orange wavelength region. - Highlights: • Combustion synthesis route is used to prepare the SrAl{sub 2}O{sub 4}: Dy {sup 3+} nanophosphors. • The size of the synthesized sample was found to be in the nano-meter range. • The mechanoluminescence of SrAl{sub 2}O{sub 4}:Dy {sup 3+} nanophosphors is studied. • The photoluminescence of SrAl{sub 2}O{sub 4}: Dy {sup 3+} nanophosphors showed blue-shift as compared to bulk. • Effect of H{sub 3}BO{sub 3} on the mechanoluminescence of SrAl{sub 2}O{sub 4}:Dy{sup 3+} was studied.

Thermoluminescent dosimetry and assessment of personal dose

International Nuclear Information System (INIS)

Boas, J.F.; Martin, L.J.; Young, J.G.

1982-01-01

Thermoluminescence is discussed in terms of the energy band structure of a crystalline solid and the trapping of charge carriers by point defects. Some general properties of thermoluminescent materials used for dosimetry are outlined, with thermoluminescence of CaSO 4 :Dy being described in detail. The energy response function and the modification of the energy response of a dosimeter by shielding are discussed. The final section covers the connection between exposure, as recorded by a TLD badge, and the absorbed dose to various organs from gamma radiation in a uranium mine; the conversion from absorbed dose to dose equivalent; and uncertainties in assessment of dose equivalent

Ambient radiation levels in a microPET/CT research laboratory

International Nuclear Information System (INIS)

Sarmento, D.M.; Rodrigues, D.L.; Sanches, M.P.; Carneiro, J.C.G.G.

2015-01-01

This study focuses on initial radiological evaluation and the exposure situation related to the worker task in a micro-positron emission tomography/computed tomography laboratory (microPET/CT). Selected and calibrated thermoluminescent dosimeters, TLD, of CaSO 4 :Dy were used to measure room radiation levels. The detectors were placed in several selected points inside the microPET/CT laboratory and adjacent rooms. In addition, the occupationally exposed workers were monthly evaluated for external and internal exposures. In none of the selected points the dose values exceeded the radiation dose limit established for supervised area, as well as the values obtained in individual monitoring. (author)

A new TLD system for space research

International Nuclear Information System (INIS)

Feher, I.; Deme, S.; Szabo, B.; Vagvoelgyi, J.; Szabo, P.P.; Csoeke, A.; Ranky, M.; Akatov, Yu.A.

1980-06-01

A small, portable, vibration and shock resistant thermoluminescent dosemeter (TLD) system was developed to measure the cosmic radiation dose on board of a spacecraft. The TLD system consists of a special bulb dosemeter and a TLD reader. The measuring dose range of the TLD system is from 10 μGy up to 100 mGy. The TLD reader can operate on a battery; its electrical power consumption is about 5 W, its volume is about 1 dm 3 and its mass is about 1 kg. Details are given of the construction and technical parameters of the dosemeter and reader. (author)

New method of preparation of CaSO{sub 4}: Dy for ionizing radiation dosimetry; Nuevo metodo de preparacion del CaSO{sub 4}: Dy para dosimetria de radiacion ionizante

Energy Technology Data Exchange (ETDEWEB)

Roman L, J.; Rivera M, T.; Alarcon F, G.; Guzman M, J. [CICATA-IPN, 11500 Mexico D.F. (Mexico); Azorin N, J.; Sosa F, R. [UAM-I, 09340 Mexico D.F. (Mexico); Serrano F, A.K. [Hospital Juarez General de Mexico, 07760 Mexico D.F. (Mexico)]. e-mail: holand_jeos@hotmail.com

2008-07-01

In this work some results of the characterization of solid state materials exposed at a gamma radiation beam coming from a {sup 60} Co bomb for medical use are presented. These thermoluminescent dosemeters are prepared and proposed for the ionizing radiations dosimetry using the thermoluminescence method. The passive dosemeters of CaSO{sub 4}: Dy are developed in the polycrystalline powder form being used a new synthesis route by means of the precipitation method. To determine the sensibility of the pellets of CaSO{sub 4}: Dy before gamma radiation, these were exposed before a gamma radiation beam coming from a {sup 60} Co bomb. The morphological and structural characteristics were also studied and present two in this work. (Author)

Dose profile for electron beams obtained with CaSO{sub 4}:Ce,Eu thermoluminescent dosimeters; Perfil de dose de feixes de eletrons obtidos com dosimetros termoluminescentes de CaSO{sub 4}:Ce,Eu

Energy Technology Data Exchange (ETDEWEB)

Nunes, Maira G.; Rodrigues, Leticia L.C., E-mail: mgnunes@ipen.br [Instituto de Pesquisas Energerticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2012-12-15

The calcium sulphate activated with cerium and europium (CaSO{sub 4}:Ce,Eu) thermoluminescent dosimeters (TLD) recently developed at Nuclear and Energy Research Institute as well as the calcium sulphate activated with dysprosium (CaSO{sub 4}: Dy) and lithium fluoride activated with magnesium and titanium, (LiF:Mg,Ti; TLD-100) TLDs, with long term applications in dosimetry and considered as standards, were used to obtain the dose profile for 3.43, 5.48, 8.27 and 11.67 MeV electron beams generated by a linear accelerator Clinac 2100-C (Varian) in the reference conditions defined by the TRS-398 code of practice. The routine dosimetry of the electron beams, performed with a calibrated ionization chamber, ensures that the electron beams fulfill the requirements of flatness and symmetry established in this code of practice. Thus, as the TRS-398 Code of Practice requirements are fulfilled by the measurements performed with the new TLD type, CaSO{sub 4}:Ce,Eu may be applied in clinical dosimetry of high energy electron beams. (author)

Evolution of the orbitals Dy-4f in the DyB2 compound using the LDA, PBE approximations, and the PBE0 hybrid functional

Science.gov (United States)

Rasero Causil, Diego; Ortega López, César; Espitia Rico, Miguel

2018-04-01

Computational calculations of total energy based on density functional theory were used to investigate the structural, electronic, and magnetic properties of the DyB2 compounds in the hexagonal structure. The calculations were carried out by means of the full-potential linearized augmented plane wave (FP-LAPW) method, employing the computational Wien2k package. The local density approximation (LDA) and the generalized gradient approximation (GGA) were used for the electron-electron interactions. Additionally, we used the functional hybrid PBE0 for a better description the electronic and magnetic properties, because the DyB2 compound is a strongly-correlated system. We found that the calculated lattice constant agrees well with the values reported theoretically and experimentally. The density of states (DOS) calculation shows that the compound exhibits a metallic behavior and has magnetic properties, with a total magnetic moment of 5.47 μ0/cell determined mainly by the 4f states of the rare earth elements. The functional PBE0 shows a strong localization of the Dy-4f orbitals.

161Dy Moessbauer spectroscopy of the intermetallic compounds DyNi2Si2, DyNi2Ge2 and DyAg2Si2

International Nuclear Information System (INIS)

Onodera, Hideya; Murata, Akifumi; Koizuka, Masaaki; Ohashi, Masayoshi; Yamaguchi, Yasuo

1994-01-01

161 Dy Moessbauer spectroscopic study has been performed on DyNi 2 Si 2 , DyNi 2 Ge 2 and DyAg 2 Si 2 in order to clarify microscopic properties of antiferromagnets with incommensurate and sinusoidally moment-modulated structure. The experiments were done using the standard 161 Tb Moessbauer sources prepared by neutron irradiation at the Japan Material Testing Reactor. The Moessbauer spectra of DyNi 2 Si 2 are analyzed satisfactorily by a single set of hyperfine parameters, and hence the sinusoidal moment-modulation is considered to be realized through a distribution of spin relaxation rate. The broadened spectra of DyNi 2 Ge 2 are fitted tentatively by three subspectra. It seems for DyNi 2 Ge 2 that the incommensurate arrangement of Dy moments differed in magnitude as well as the distribution of spin relaxation rate originates the moment modulation. The fact that the spectrum of DyAg 2 Si 2 at 3 K consists of two distinct subspectra ensures the complicated antiferromagnetic structure where two kinds of Dy moments differed in magnitude are arranged noncollinearly. (author)

Spectral properties of Dy3+ doped ZnAl2O4 phosphor

Science.gov (United States)

Prakash, Ram; Kumar, Sandeep; Mahajan, Rubby; Khajuria, Pooja; Kumar, Vinay; Choudhary, R. J.; Phase, D. M.

2018-05-01

Herein, Dy3+ doped ZnAl2O4 phosphor was synthesized by the solution combustion method. The synthesized phosphor was characterized by X-ray diffraction (XRD), photoluminescence (PL) spectroscopy, UV-Vis spectroscopy and X-ray photoelectron spectroscopy (XPS). The phase purity of the phosphor was confirmed by the XRD studies that showed cubic symmetry of the synthesized phosphor. Under UV excitation (388 nm) the PL emission spectrum of the phosphor shows characteristic transition from the Dy3+ ion. A band gap of 5.2 eV was estimated from the diffused reflectance spectroscopy. The surface properties of the phosphor were studied using the X-ray photoelectron spectroscopy.

Phase equilibria in Dy-Cu-Al system at 500 deg C

International Nuclear Information System (INIS)

Kuz'ma, Yu.B.; Milyan, V.V.

1989-01-01

Using the methods of X-ray diffraction analysis a diagram of phase equilibria in Dy-Cu-Al system at 500 deg C is plotted. Boundaries of solid solutions on the basis of DyCu 2 , DyCu and DyAl 2 compounds are determined and homogeneity regions of ternary compounds Dy 2 (Cu, Al) 7 and Dy(CuAl) 5 are ascertained. Compounds DyCuAl 3 , Dy 4 Cu 4 Al 11 and Dy 5 Cu 6 Al 9 have been detected for the first time

White Light Emitting MZr4(PO4)6:Dy3+ (M = Ca, Sr, Ba) Phosphors for WLEDs.

Science.gov (United States)

Nair, Govind B; Dhoble, S J

2017-03-01

A series of MZr 4 (PO 4 ) 6 :Dy 3+ (M = Ca, Sr, Ba) phosphors were prepared by the solid state diffusion method. Confirmation of the phase formation and morphological studies were performed by X-ray powder diffraction (XRD) measurements and scanning electron microscopy, respectively. Photoluminescence (PL) properties of these phosphors were thoroughly analyzed and the characteristic emissions of Dy 3+ ions were found to arise from them at an excitation wavelength of 351 nm. The PL emission spectra of the three phosphors were analyzed and compared. The CIE chromaticity coordinates assured that the phosphors produced cool white-light emission and hence, they are potential candidates for UV excited white-LEDs (WLEDs). Graphical Abstract ᅟ.

Synthesis, crystal structure, optical and thermal properties of lanthanide hydrogen-polyphosphates Ln[H(PO3)4] (Ln = Tb, Dy, Ho).

Science.gov (United States)

Förg, Katharina; Höppe, Henning A

2015-11-28

Lanthanide hydrogen-polyphosphates Ln[H(PO3)4] (Ln = Tb, Dy, Ho) were synthesised as colourless (Ln = Tb, Dy) and light pink (Ln = Ho) crystalline powders by reaction of Tb4O7/Dy2O3/Ho2O3 with H3PO3 at 380 °C. All compounds crystallise isotypically (P2(1)/c (no. 14), Z = 4, a(Tb) = 1368.24(4) pm, b(Tb) = 710.42(2) pm, c(Tb) = 965.79(3) pm, β(Tb) = 101.200(1)°, 3112 data, 160 parameters, wR2 = 0.062, a(Ho) = 1363.34(5) pm, b(Ho) = 709.24(3) pm, c(Ho) = 959.07(4) pm, β(Ho) = 101.055(1)°, 1607 data, 158 parameters, wR2 = 0.058). The crystal structure comprises two different infinite helical chains of corner-sharing phosphate tetrahedra. In-between these chains the lanthanide ions are located, coordinated by seven oxygen atoms belonging to four different polyphosphate chains. Vibrational, UV/Vis and fluorescence spectra of Ln[H(PO3)4] (Ln = Tb, Dy, Ho) as well as Dy[H(PO3)4]:Ln (Ln = Ce, Eu) and the magnetic and thermal behaviour of Tb[H(PO3)4] are reported.

Correlation of Structure, Tunable Colors, and Lifetimes of (Sr, Ca, Ba)Al2O4:Eu2+, Dy3+ Phosphors

OpenAIRE

Qidi Xie; Bowen Li; Xin He; Mei Zhang; Yan Chen; Qingguang Zeng

2017-01-01

(Sr, Ca, Ba)Al2O4:Eu2+, Dy3+ phosphors were prepared via a high temperature solid-state reaction method. The correlation of phase structure, optical properties and lifetimes of the phosphors are investigated in this work. For the (Sr, Ca)Al2O4:Eu2+, Dy3+ phosphors, the different phase formation from monoclinic SrAl2O4 phase to hexagonal SrAl2O4 phase to monoclinic CaAl2O4 phase was observed when the Ca content increased. The emission color of SrAl2O4:Eu2+, Dy3+ phosphors varied from green to ...

Magnetic properties of Dy/Zr multilayers

International Nuclear Information System (INIS)

Luche, M.C.; Boyer, P.

1992-01-01

[Dy(xA)/Zr(30A)] n superlattices (x ≤ 30), were evaporated under ultra-high vacuum on Si(100) substrates. Magnetization measurements indicate that the antiferromagnetic transition occurring at 178K in bulk Dy is suppressed in the multilayers. This phenomenon is attributed to magnetoelastic effects induced by strains at Zr/Dy interfaces. A perpendicular magnetic anisotropy takes place for x ≤ 15. However, the magnetic anisotropy is found to depend markedly on the technique used for Dy deposition. (author). 11 refs., 4 figs

Correlation of Structure, Tunable Colors, and Lifetimes of (Sr, Ca, Ba)Al2O4:Eu2+, Dy3+ Phosphors

Science.gov (United States)

Xie, Qidi; Li, Bowen; He, Xin; Zhang, Mei; Chen, Yan; Zeng, Qingguang

2017-01-01

(Sr, Ca, Ba)Al2O4:Eu2+, Dy3+ phosphors were prepared via a high temperature solid-state reaction method. The correlation of phase structure, optical properties and lifetimes of the phosphors are investigated in this work. For the (Sr, Ca)Al2O4:Eu2+, Dy3+ phosphors, the different phase formation from monoclinic SrAl2O4 phase to hexagonal SrAl2O4 phase to monoclinic CaAl2O4 phase was observed when the Ca content increased. The emission color of SrAl2O4:Eu2+, Dy3+ phosphors varied from green to blue. For the (Sr, Ba)Al2O4:Eu2+, Dy3+ phosphors, different phase formation from the monoclinic SrAl2O4 phase to the hexagonal BaAl2O4 phase was observed, along with a shift of emission wavelength from 520 nm to 500 nm. More interestingly, the decay time of SrAl2O4:Eu2+, Dy3+ changed due to the different phase formations. Lifetime can be dramatically shortened by the substitution of Sr2+ with Ba2+ cations, resulting in improving the performance of the alternating current light emitting diode (AC-LED). Finally, intense LEDs are successfully obtained by combining these phosphors with Ga(In)N near UV chips. PMID:29057839

Correlation of Structure, Tunable Colors, and Lifetimes of (Sr, Ca, BaAl2O4:Eu2+, Dy3+ Phosphors

Directory of Open Access Journals (Sweden)

Qidi Xie

2017-10-01

Full Text Available (Sr, Ca, BaAl2O4:Eu2+, Dy3+ phosphors were prepared via a high temperature solid-state reaction method. The correlation of phase structure, optical properties and lifetimes of the phosphors are investigated in this work. For the (Sr, CaAl2O4:Eu2+,Dy3+ phosphors, the different phase formation from monoclinic SrAl2O4 phase to hexagonal SrAl2O4 phase to monoclinic CaAl2O4 phase was observed when the Ca content increased. The emission color of SrAl2O4:Eu2+, Dy3+ phosphors varied from green to blue. For the (Sr, BaAl2O4:Eu2+, Dy3+ phosphors, different phase formation from the monoclinic SrAl2O4 phase to the hexagonal BaAl2O4 phase was observed, along with a shift of emission wavelength from 520 nm to 500 nm. More interestingly, the decay time of SrAl2O4:Eu2+, Dy3+changed due to the different phase formations. Lifetime can be dramatically shortened by the substitution of Sr2+ with Ba2+ cations, resulting in improving the performance of the alternating current light emitting diode (AC-LED. Finally, intense LEDs are successfully obtained by combining these phosphors with Ga(InN near UV chips.

Investigation of thermoluminescent response of K2YF5:Dy3+ crystals for gamma and X radiation fields

International Nuclear Information System (INIS)

Silva, E.C.; Nogueira, M.S.; Faria, L.O.; Khaidukov, N.M.

2005-01-01

K 2 YF 5 crystals doped with rare earths have been synthesized with 0 to 100% of Dy 3+ ions optically active ions and an investigation was conducted to test its thermoluminescent (TL) response due to function of Dy 3+ concentration and their response in energy. After being irradiated with gamma and X-rays, it was observed that crystals doped with 1.0% of Dy 3+ feature the best response TL. The main dosimetric peak can be decomposed into three secondary TL peaks, centered in 96.4, 104.9 and 130.7 deg C, respectively, showing a good linearity and reproducibility of the dose measurements. The sensitization process seems to improve response TL and TL peak sensitivity increase to 130, 7 deg C at the expense of TL peak to 104, 9 deg C. The linear coefficient sign TL for K 2 Y 0.09 Dy 0.01 F5 is comparable to that of the dosemeter CaSO 4 : Mn, irradiated with gamma radiation source ( 137 Cs) under the same conditions. Energy dependence measurements show that the answer for X-rays with energy of 41.1 keV is more than 30 times the response to Cs-137, when exposed to the same dose. Due to the main peak in low temperature and the TL high reply to low energy fields, the results reported indicate that the K 2 YF 5 crystals doped with Dy 3+ present great potential for radiation dosimetry in X-rays therapy, clinical dosimetry and also for applications in digital thermoluminescent images

Synthesis and luminescence properties of novel Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Xu, Qiguang; Sun, Jiayue, E-mail: Jiayue_sun@126.com; Cui, Dianpeng; Di, Qiumei; Zeng, Junhui

2015-02-15

Sr{sub 3}(Gd{sub 1−x}Dy{sub x})(PO{sub 4}){sub 3} phosphors for white light-emitting diodes (w-LEDs) were prepared by the conventional solid-state reaction. X-ray diffraction (XRD) and photoluminescence spectra were utilized to characterize the structure and luminescence properties of the as-synthesized phosphors. Luminescence properties shows that the phosphor can be efficiently excited by the ultraviolet visible light in the region from 300 to 450 nm, and it exhibits blue (483 nm) and yellow (575 nm) emission corresponding to {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} transition and {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} transition, respectively. It has been found that concentration quenching occurs via dipole–dipole interaction according to Dexter's theory. The temperature dependence of photoluminescence properties is investigated from 25 to 250 °C and the prepared Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphors show good thermal quenching properties. - Highlights: • Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphors were synthesized by a solid-state reaction method. • The phosphor could be efficiently excited by the UV–vis light region from 300 to 450 nm. • Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphors exhibited blue (483 nm) and yellow (575 nm) emission. • The Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphors concentration quenching occurred as a result of dipole–dipole interaction. • Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphors showed good thermal quenching properties.

Environmental monitoring system with TLD; Sistema de monitoreo ambiental con TLD

Energy Technology Data Exchange (ETDEWEB)

Aguerre, L.; Carelli, J.; Gregori, B. [Autoridad Regulatoria Nuclear Argentina (Argentina)]. e-mail: laguerre@cae.arn.gov.ar

2006-07-01

Presently work the methodology used by the Laboratory of Thermoluminescent Dosimetry (TLD) of the Nuclear Regulatory Authority (RNA) to gauge it system of environmental monitoring in function of the media absorbed dose rate in free air and the environmental dose equivalent, H{sup *}(10), according to the recommendation ICRU Report 47 is described. It was studied the response of the environmental dosemeter (DA) in fields of photonic radiation of energies W60, Wl 10, W200 and {sup 137} Cs. The irradiations were carried out following the recommendations of the standard ISO:4037. It was analyzed the response in the DA of the detectors LiF: Mg, Ti and CaF{sub 2}: Dy for the different radiation qualities and the relative response at {sup 137} Cs of both. The methodology used in the evaluation of the dose includes: the correction of the readings of both detectors by fading, gotten experimentally, the witness of transfers, the energy answer and the value of the zero. The dose is calculated applying the average pondered in uncertainty of the dose obtained for each type of detector. Its were analyzed and calculated the uncertainties that affect to the measurement following the recommendation of the Argentine standard IRAM 35050. The detection limit of the absorbed dose rate in free air of this system it is 3.5 n Gy/h for a period of sampling of 3 months. With this detection limit environmental dose equivalent rates of the order of 70 n Sv/h are measured with an expanded uncertainty of the order of 10% with a cover factor k = 2. (Author)

Isothermal sections at 500 deg C of the Dy-V-Al and Dy-Cr-Al systems in the aluminium rich regions

International Nuclear Information System (INIS)

Rykhal', R.M.; Zarechnyuk, O.S.; Mats'kiv, O.P.

1979-01-01

X-ray diffraction and microscopic analyses have been used to investigate the ternary system dysprosium-vanadium-aluminium in the aluminium rich region. In the system Dy-V-Al two ternary compounds have been found: DyV 2 Al 20 (cubic structure, CeCr 2 Al 20 type, a=14.54 A and approximately DyVAl 8 (hexagonal crystal system, structure unknown, a=10.86, c=17.71 A, c/a=1.631). In the system dysprosium-chromium-aluminium three ternary compounds have been found: DyCr 2 Al 20 (cubic structure, CeCr 2 Al 20 type, a=14.39), approximately equal to DyCrAl 8 ) hexagonal crystal system, structure type unkown a=10.75, c=17.60 A, c/a=1.637) and DyCr 4 Al 8 (tetragonal structure, CeMn 4 Al 8 type, a=8.87, c=5.04 A, c/a=0.568). Isothermal sections of the systems Dy-V-Al and Dy-Cr-Al have been plotted at 500 deg C

The role of dysprosium on the structural and magnetic properties of (Nd_1_−_xDy_x)_2Fe_1_4B nanoparticles

International Nuclear Information System (INIS)

Rahimi, Hamed; Ghasemi, Ali; Mozaffarinia, Reza; Tavoosi, Majid

2017-01-01

In current work, Nd2Fe14B nanoparticles was synthesized by sol-gel method. Dysprosium powders were added into Nd2Fe14B nanoparticles by mechanical alloying process in order to enhancement of coercivity. The phase analysis, structure, and magnetic properties of annealed (Nd_1_−_xDy_x)_2Fe_1_4B nanoparticles with different Dy-content (x=0.1, 0.2, 0.3, 0.4, 0.5, 0.6) were investigated by employing X-ray diffraction, X-ray photoelectron spectroscopy, energy dispersive spectroscopy, field emission scanning electron microscope, transmission electron microscope and vibrating sample magnetometer techniques. The results showed that with an increase in Dy amounts, the coercivity of particles increased from 2.9 kOe to 13.4 kOe and then decreased to 5.6 kOe. By adding an optimum amount of Dy (x=0.4), the coercivity was significantly increased from 2.9 kOe to 13.4 kOe. The average particle size of annealed (Nd_1_−_xDy_x)_2Fe_1_4B nanoparticles was below 10 nm. Magnetization reversal studies indicate that the coercivity of milled and annealed (Nd_1_−_xDy_x)_2Fe_1_4B nanoparticles is controlled by the nucleation of reversed magnetic domains. The experimental results in the angular dependence of coercivity for (Nd_1_−_xDy_x)_2Fe_1_4B permanent magnets showed that the normalized coercivity of the permanent magnets H_c(θ)/H_c(0) increases from 1 to about 1.2–1.5 with increasing θ from 0 to about π/3, for x=0.4–0.6. - Highlights: • Dy was added to Nd_2Fe_1_4B nanoparticles to improve the coercivity. • A maximum squareness ratio of 0.99 was obtained. • The average particle size decreased with an increase in Dy-content.

Investigation of LiF, Mg and Ti (TLD-100) Reproducibility.

Science.gov (United States)

Sadeghi, M; Sina, S; Faghihi, R

2015-12-01

LiF, Mg and Ti cubical TLD chips (known as TLD-100) are widely used for dosimetry purposes. The repeatability of TL dosimetry is investigated by exposing them to doses of (81, 162 and 40.5 mGy) with 662keV photons of Cs-137. A group of 40 cubical TLD chips was randomly selected from a batch and the values of Element Correction Coefficient (ECC) were obtained 4 times by irradiating them to doses of 81 mGy (two times), 162mGy and 40.5mGy. Results of this study indicate that the average reproducibility of ECC calculation for 40 TLDs is 1.5%, while these values for all chips do not exceed 5%.

Investigation of thermoluminescence and electron-vibrational interaction parameters in SrAl2O4:Eu2+, Dy3+ phosphors

International Nuclear Information System (INIS)

Pardhi, Shilpa A.; Nair, Govind B.; Sharma, Ravi; Dhoble, S.J.

2017-01-01

Combustion synthesis method was employed for the synthesis of green-emitting monoclinic SrAl 2 O 4 :Eu 2+ , Dy 3+ phosphors. The phase-purity of the prepared phosphors were examined using X-ray diffraction (XRD). The prepared phosphors exhibited green light emission with the peak centred at 510 nm, under 350 nm UV excitation. The excitation and emission spectra were analysed and the parameters of electron-vibrational interaction (EVI), such as the Huang–Rhys factor, effective phonon energy and zero-phonon line position were estimated using the spectrum fitting method. Thermoluminescence (TL) behaviour of the as-prepared phosphors were analysed for UV and 137 Cs γ-ray source irradiation. TL glow curves for UV-irradiated SrAl 2 O 4 :Eu 2+ , Dy 3+ phosphors were analysed. - Highlights: • Photoluminescence and thermoluminescence properties of SrAl 2 O 4 :Eu 2+ ,Dy 3+ phosphors were analysed. • Electron-vibrational interaction (EVI) parameters of SrAl 2 O 4 :Eu 2+ ,Dy 3+ phosphors were determined. • The phosphors are found to exhibit green light emission.

Relieving geometrical frustration through doping in the Dy1−x Cax BaCo4O7 swedenborgites

International Nuclear Information System (INIS)

Nath Panja, Soumendra; Kumar, Jitender; Dengre, Shanu; Nair, Sunil

2016-01-01

The geometrically frustrated antiferromagnet DyBaCo 4 O 7 is investigated through a combination of x-ray diffraction, magnetization and dielectric measurements. Systematic doping in the series Dy 1−x Ca x BaCo 4 O 7 causes a lifting of the geometrical frustration resulting in a structural transition from a trigonal P31c to an orthorhombic Pbn2 1 symmetry at x   =  0.4. This structural transition can also be accessed as a function of temperature, and all our orthorhombic specimens exhibit this transition at elevated temperatures. The temperature at which this structural transition occurs is observed to scale linearly with the mean ionic radius of the R site ion. However, CaBaCo 4 O 7 which has an equal number of Co 2+  and Co 3+ ions clearly violates this quasilinear relationship, indicating that charge ordering could also play a critical role in stabilizing the orthorhombic distortion in this system. Using thermoremanent magnetization measurements to circumvent the problem of the large paramagnetic background arising from Dy 3+ ions, we chart out the phase diagram of the Dy 1−x Ca x BaCo 4 O 7 series. (paper)

Preparation of CaF{sub 2}:Dy chips as thermoluminescent dosimeters for environmental measurements using a Harshaw 2080 TL picoprocessor

Energy Technology Data Exchange (ETDEWEB)

Matoso, Erika; Leite, Barbara Eliodora [Centro Tecnologico da Marinha em Sao Paulo (CTMSP/CEA), Ipero, SP (Brazil). Centro Experimental Aramar; Nunes, Maira Goes [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

This work presents the necessary steps to prepare the dosimeters for application in environmental measurements. The material used was calcium fluoride doped with dysprosium (CaF{sub 2}: Dy), commercially supplied by Harshaw as TLD-200. It were carried out four initial irradiations (Co-60 source gamma - 0.8 mGy from Dosimetric Material Laboratory LMD/GMP) in a new batch of TLD-200 dosimeters to achieve a stable response and four more irradiations to separate them, according to their response range. A batch of pre-selected 197 dosimeters from 263 was used to finally obtained two batches of 99 (9.2{+-}0.7nC) and 93 (10.5{+-}0.6nC) dosimeters. A calibration curve was prepared relating the thermoluminescent response of the phosphor and the radiation exposure (0 to 600{mu}Gy), obtained by irradiation with Co-60 source of 4P geometry and measurements using a Harshaw Picoprocessor 2080 TL equipment. Repeatability of the measurements was determined for 100{mu}Gy (CV= 5.09%) and 300{mu}Gy (CV=4.18%) and the minimum detectable dose was evaluated as 2{mu}Gy. The fading was determined by irradiating the dosimeters with 0.8 mGy and reading then after 1, 5, 7, 8, 15, 29, 50, 70 and 90 days. (author)

RFID based TLD monitoring system - a prospective development

International Nuclear Information System (INIS)

Jeevanram, S.S.; Pawar, S.T.; Mahule, K.N.; Rath, D.P.

2008-01-01

Thermo Luminescence Dosimetry (TLD) is an established method of monitoring the radiation dose received by workers in radiation environments. In Radiometallurgy Laboratory, BARC, the TLD movement inside a nuclear facility is completely carried out by a radiation worker. However, there is a chance that the TLDs may get lost in laboratories or some places without the knowledge of the concerned TLD user or health physicist. It may later lead to a false effective dose. Effort is being done to initiate a RFID based TLD monitoring system so that the use of TLD can be acknowledged through a self operating software which can prevent misuse of the detector. A novel method of improving the administrative control through Radio Frequency Identification (RFID) based monitoring to avoid such inadvertent misplacement of TLD, is in progress. This paper discusses the method and techniques through which administrative control can be exercised to reduce the number of such in explainable exposures. (author)

Near white light emitting ZnAl2O4:Dy3+ nanocrystals: Sol–gel synthesis and luminescence studies

International Nuclear Information System (INIS)

Kumar, Mithlesh; Gupta, Santosh K.; Kadam, R.M.

2016-01-01

Highlights: • ZnAl 2 O 4 :Dy 3+ spinel synthesized using sol–gel method. • Characterized by XRD, SEM and PL spectroscopy. • Investigations of emission, excitation and lifetime properties. • Evaluation of defect centers and trap parameters of the system. • Evaluation of CIE indices of near white light emitting phosphor. - Abstract: ZnAl 2 O 4 :Dy 3+ nanoparticles were synthesized using citrate sol–gel method and characterized systematically using X-ray diffraction, scanning electron microscopy and photoluminescence spectroscopy. Emission spectrum of pure ZnAl 2 O 4 shows intense violet blue emission under ultra violet irradiation. Based on electron paramagnetic resonance (EPR) results; it was attributed to presence of singly ionized oxygen vacancy centres in ZnAl 2 O 4 . On doping Dy 3+ in ZnAl 2 O 4 , complete host–dopant energy transfer does not take place. Local structural investigation and lifetime measurements reveal that dysprosium ion is distributed between both Zn 2+ and Al 3+ sites. Near white light from ZnAl 2 O 4 :Dy 3+ is attributed to combined host and dopant luminescence. The trap parameters such as activation energy (E) and frequency factor (s) for TSL glow peak 165 °C were determined using different heating rate method. Thermally stimulated emission showed the presence of oxygen related defect centre.

X-rays individual dose assessment using TLD dosimeters

International Nuclear Information System (INIS)

Salas, Carlos

2008-01-01

This paper describes the methodology used in Embalse NPP for measuring individual X-ray dose in dentists and radiologists, who work in areas near the plant. Personnel is provided with TLD personal dosimeters for thoracic use, as well as TLD ring dosimeters. This individual X-ray dosimetry is fundamental in order to know the effective energy coming from the radiation field, since the dosimetry factors depend on it. On the other hand, the response of the TLD crystals also depends of the effective energy; this accentuates the problem when assessing the individual dose. The X-ray dosimeter must simultaneously determine the value of the effective energy and the corresponding dose value. The basic principle for determining effective energy is by using at least two different TLD materials covered by filters of different thickness. The TLD materials used have totally energy responses. Therefore, different readouts from each of the crystals are obtained. The ratio between both readouts provides a factor that depends of the effective energy but that is 'independent' from the exposure values irradiated to the dosimeter. The Personal TLD dosimeter currently in use is Bicron-Harshaw. It comprises a carrier model 8807. This carrier contains a card model 2211 which groups two TLD 200 crystals and two TLD 100 crystals. It has internal filters at each side of the TLD 200 crystals. The periodical calibration of these dosimeters consists in the irradiation of some dosimeters with different X-ray energy beams in the National Atomic Energy Commission (CNEA). This dosimeter was used, by the National Regulatory Authority (ARN) in several comparisons, always getting satisfactory results. (author)

Investigation of LiF, Mg and Ti (TLD-100 Reproducibility

Directory of Open Access Journals (Sweden)

Sadeghi M.

2015-12-01

Full Text Available LiF, Mg and Ti cubical TLD chips (known as TLD-100 are widely used for dosimetry purposes. The repeatability of TL dosimetry is investigated by exposing them to doses of (81, 162 and 40.5 mGy with 662keV photons of Cs-137. A group of 40 cubical TLD chips was randomly selected from a batch and the values of Element Correction Coefficient (ECC were obtained 4 times by irradiating them to doses of 81 mGy (two times, 162mGy and 40.5mGy. Results of this study indicate that the average reproducibility of ECC calculation for 40 TLDs is 1.5%, while these values for all chips do not exceed 5%.

Persistent luminescence and thermoluminescence of UV/VIS -irradiated SrAl2O4: Eu2+, Dy3+ phosphor

International Nuclear Information System (INIS)

Pereyda-Pierre, C.; Meléndrez, R.; García, R.; Pedroza-Montero, M.; Barboza-Flores, M.

2011-01-01

The persistent luminescence and thermoluminescence properties of SrAl 2 O 4 : Eu 2+ , Dy 3+ phosphors excited with UV–VIS light in the 200–500 nm region were investigated. The thermoluminescence glow curve was found to be composed of peaks around 70, 125 and 245 °C. The persistent luminescence and thermoluminescence excitation spectra exhibited a broad band around 300–500 nm centered at 400 and 420 nm respectively. A linear behavior of the integrated thermoluminescence intensity and persistent luminescence versus irradiation time was found for the first 60 s. The charge detrapping from the 70 °C trapping levels was the major contributor to the observed persistent luminescence at room temperature. The SrAl 2 O 4 : Eu 2+ , Dy 3+ phosphors have suitable properties to be applied as storage and persistent luminescence UV–VIS irradiation dose phosphor. -- Highlights: ► SrAl 2 O 4 :Eu 2+ , Dy 3+ persistent luminescence and thermoluminescence was measured. ► The phosphor was irradiated with UV–VIS photons in the 200–500 nm wavelength range. ► SrAl 2 O 4 :Eu 2+ , Dy 3+ behaves adequately as persistent and storage UV–VIS dosimeter. ► The persistent luminescence dosimetry does not require heat or light stimulation.

Effect of UV irradiation on different types of luminescence of SrAl2 O4 :Eu,Dy phosphors.

Science.gov (United States)

Jha, Piyush

2016-11-01

This paper reports the luminescence behavior of Sr 0.097 Al 2 O 4 :Eu 0.01 ,Dy 0.02 phosphors under UV-irradiation. The effect of UV-irradiation on afterglow (AG), thermoluminescence (TL) and mechanoluminescence (ML) of Sr 0.097 Al 2 O 4 :Eu 0.01 ,Dy 0.02 phosphors is investigated. The space group of Sr 0.097 Al 2 O 4 :Eu 0.01 ,Dy 0.02 phosphors is monoclinic P2 1 . The prepared phosphors exhibit a long AG, intense TL and ML. It is found that the AG, ML intensity and TL increase with increasing duration of irradiation time. The ML intensity decreases with successive impact of the load onto the phosphors, whereby the diminished ML intensity can be recovered by UV-irradiation. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

An automated thermoluminescence dosimetry (TLD) system

International Nuclear Information System (INIS)

Kicken, P.J.H.; Huyskens, C.J.

1979-01-01

In the Health Physics Division of the Eindhoven University of Technology work is going on in developing an automated TLD-system. Process automization, statistical computation, dose calculation as well as dose recording are carried out, using a microcomputer and floppy disk unit. The main features of this TLD-system are its low costs, flexibility, easy to operate, and the feasibility for use in routine dosimetry as well as in complex TLD research. Because of its modular set-up several components of the system are multifunctional in other operations. The system seems suited for medium sized Health Physics groups. (Auth.)

Fabrication and Luminescent properties of ZnWO{sub 4}:Eu{sup 3+}, Dy{sup 3+} white light-emitting phosphors

Energy Technology Data Exchange (ETDEWEB)

Zhai, Yongqing, E-mail: zhaiyongqinghbu@163.com; Wang, Meng; Zhao, Qian; Yu, Jiabao; Li, Xuemin

2016-04-15

ZnWO{sub 4}:Eu{sup 3+},Dy{sup 3+} white light-emitting phosphors were prepared by a hydrothermal method followed with calcination process. The as-synthesized phosphors were characterized by X-ray powder diffraction (XRD), Fourier transform infrared (FTIR) spectrum, Raman spectra, scanning electron microscope (SEM), transmission electron microscope (TEM), diffused reflectance spectra, photoluminescence excitation and emission spectra, and photoluminescence decay curves. Furthermore, external quantum efficiency of ZnWO{sub 4}:Eu{sup 3+},Dy{sup 3+} was determined. The results showed that the obtained phosphors have monoclinic wolframite structure. The particles of the phosphors was nearly spherical in shape, and the particle size was about 70–100 nm. Upon excitation at UV light, the white light-emitting can be obtained by combining the blue–green emission of tungstate group and characteristic emission of Eu{sup 3+} and Dy{sup 3+}. Based on the excitation/emission spectra and decay curves, the energy transfer and photoluminescence mechanism for ZnWO{sub 4}:Eu{sup 3+}, Dy{sup 3+} system were discussed.

TLD audit in radiotherapy in the Czech Republic

International Nuclear Information System (INIS)

Kroutilikova, D.; Zackova, H.; Judas, L.

1998-01-01

National Radiation Protection Institute in Prague organizes the TLD audit. The aim of the TLD postal audit is to provide control of the clinical dosimetry in the Czech Republic for purposes of state supervision in radiotherapy, to investigate and to reduce uncertainties involved in the measurements of absorbed dose and to improve consistency in dose determination in the regional radiotherapy centers. TLD audit covers absorbed dose measurements under reference conditions for 60 Co and 137 Cs beams, high-energy X-ray and electron beams of of linear accelerators and betatrons. The thermo-luminescence dosemeters are sent regularly to all radiotherapy centers. Absorbed dose measures by the TLD is compared to absorbed dose stated by radiotherapy center. Encapsulated LiF:Mg, Ti powder is used for the measurement. Deviation of 3% between stated and TLD measured dose is considered for photons and ±5% for electron beams. First TLD audit was started in 1997. A total of 135 beams was checked. There were found seven major deviations (more than ±6%), which were very carefully investigated. Medical Physicists from these departments reported a set-up mistake. However, at most of those hospitals with major deviations, an in situ audit in details was made soon after TLD audit. There were found discrepancies of clinical dosimetry but also bad technical state of some of the irradiation units. In 1998, second course TLD audit was started. No major deviation was found. Regular TLD audit seems to be a good way to eliminate big mistakes in the basic clinical dosimetry. Repeated audit in the regional radiotherapy centers that had major deviation during the first audit exhibited improvement of their dosimetry. It is intended to broaden the method and to control also beam parameters by means of a multi-purpose phantom. (authors)

Postal TLD audit in radiotherapy in the Czech Republic

International Nuclear Information System (INIS)

Kapucianova, M.; Ekendah, D. l.; Bulanek, B.

2014-01-01

The postal TLD audit in radiotherapy is an independent check of dose applied by radiotherapy centers. Our poster provides basic information on the methodology of dose determination within the TLD audit. An overview of different versions of the TLD audit that are focused on specific techniques in radiotherapy is given. We also present results of so called basic version of the TLD audit that is performed regularly for purposes of the State Office for Nuclear Safety. Moreover, results of intercomparison measurements organized by the IAEA (International Atomic Energy Agency), in which our laboratory takes part every year, are shown.The methodology of dose determination is based on TL measurement of LiF:Mg,Ti powder. The TL dosemeter (TLD) has form of a plastic capsule containing approximately 160 mg of this material. Before the TL reading, the powder of each particular irradiated dosemeter is divided into 9 identical samples by means of an accurate dispenser. The dosemeter response is given as average of TL responses of the 9 samples. The dose absorbed in water is computed from the TLD response by application of calibration factor and correction coefficients for elimination of energy dependence, supra-linearity and fading of the TL material. The evaluation of the TLD audit is based on comparison of the dose measured by the TLD and the dose stated by a radiotherapy center. Relative deviation between these doses is calculated. Several versions of the TLD audit are available. (authors)

Influence of 45S5 Bioglass addition on microstructure and properties of ultrafine grained (Mg-4Y-5.5Dy-0.5Zr) alloy

Energy Technology Data Exchange (ETDEWEB)

Kowalski, K., E-mail: kamil.kowalski@put.poznan.pl [Institute of Materials Science and Engineering, Poznan University of Technology, Jana Pawla II 24, 61-138 Poznan (Poland); Jurczyk, M.U. [Division of Mother’s and Child’s Health, Poznan University of Medical Sciences, Polna 33, 60-535 Poznan (Poland); Wirstlein, P.K. [Department of Gynecology and Obstetrics, Division of Reproduction, Poznan University of Medical Sciences, Polna 33, 60-535 Poznan (Poland); Jakubowicz, J.; Jurczyk, M. [Institute of Materials Science and Engineering, Poznan University of Technology, Jana Pawla II 24, 61-138 Poznan (Poland)

2017-05-15

Highlights: • Ultrafine grained composites were formed by consolidating mechanically alloyed powders. • Mechanical properties were sensitive to the content of 45S5 Bioglass in Mg-4Y-5.5Dy-0.5Zr alloy. • Fluoride treated composites displayed superior corrosion resistance in Ringer solution. • Composites modified with MgF{sub 2} have a higher degree of biocompatibility in comparison with the unmodified reference material. - Abstract: Bulk samples of an ultrafine grained (Mg-4Y-5.5Dy-0.5Zr)-x wt% 45S5 Bioglass (x = 0, 5) and (Mg-4Y-5.5Dy-0.5Zr)-5 wt% 45S5 Bioglass-1 wt% Ag composites have been synthesized by consolidating mechanically alloyed powders. The influence of the chemical composition on the microstructure, mechanical properties and corrosion behavior of bulk composites were studied. The sintering of (Mg-4Y-5.5Dy-0.5Zr)-5 wt% 45S5 Bioglass powders led to the formation of a bulk composite with grain size of approx. 95 nm. The corrosion behavior of Mg-based composites before and after hydrofluoric acid treatment was also investigated. The ultrafine grained (Mg-4Y-5.5Dy-0.5Zr)-5 wt% 45S5 Bioglass composite was more corrosion resistant than the bulk Mg-4Y-5.5Dy-0.5Zr alloy after HF treatment. The in vitro biocompatibility of synthesized composites was evaluated and compared with microcrystalline magnesium. Magnesium, (Mg-4Y-5.5Dy-0.5Zr)-5 wt% 45S5 Bioglass and (Mg-4Y-5.5Dy-0.5Zr)-5 wt% 45S5 Bioglass-1 wt% Ag composites modified with MgF{sub 2} have a higher degree of biocompatibility in comparison with the unmodified reference material.

The effect of urea:nitrate ratio on the structure and luminescence properties of YVO{sub 4}:Dy{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Foka, K.E., E-mail: fokake@gmail.com [Department of Physics, University of the Free State (Qwaqwa), Private Bag x13, Phuthaditjhaba 9866 (South Africa); Dejene, B.F. [Department of Physics, University of the Free State (Qwaqwa), Private Bag x13, Phuthaditjhaba 9866 (South Africa); Swart, H.C. [Department of Physics, University of the Free State, P. O. Box 339, Bloemfontein 9300 (South Africa)

2016-01-01

YVO{sub 4}:Dy{sup 3+} phosphor has been successfully synthesised using combustion method. The dependence of the properties of YVO{sub 4}:Dy{sup 3+} phosphor upon urea:nitrate concentration was investigated. The single tetragonal phase was observed by x-ray diffraction spectra. A highly crystalline YVO{sub 4}:Dy{sup 3+} sample was obtained when increasing the ratio of the urea to 2. The estimated crystalline sizes from the Scherrer’s formula were found to be 20, 38, 33, 30, and 27 nm for the sample prepared with the ratio of 1, 2, 2.5, 3 and 4, respectively. The formation of agglomerated particles was observed by Scanning electron microscope images and it was observed that when increasing the concentration of urea further, flake-like particles formed. The diffuse reflectance spectra of YVO{sub 4}:Dy{sup 3+} with various ratios of urea indicated that the determined optical band gap was ranging from 3.3 to 2.3 eV. Luminescence properties of YVO{sub 4}:Dy{sup 3+} showed that the phosphor emit yellow colour at 573 nm and blue colour at 482 nm corresponding to {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} and {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} transitions, respectively. A very weak band at 663 nm which correspond to the {sup 4}F{sub 9/2}→{sup 6}H{sub 11/2} transition was also observed. It was found that the Photoluminescent emission intensity increased with an increase in the ratio of urea and reached a maximum at 2 then decreased when increasing the ratio of urea further.

Hydrothermal synthesis and tunable luminescent properties of Sr{sub 2-x}Dy {sub x}CeO{sub 4} rod-like phosphors derived from co-precipitation precursors

Energy Technology Data Exchange (ETDEWEB)

He Xianghong [School of Chemistry and Chemical Engineering, Jiangsu Teachers' University of Technology, Changzhou, Jiangsu 213001 (China) and Jiangsu Province Key Laboratory of Precious Metal Chemistry and Technology, Changzhou, Jiangsu 213001 (China)]. E-mail: hexh@jstu.edu.cn; Li Weihua [School of Chemistry and Chemical Engineering, Jiangsu Teachers' University of Technology, Changzhou, Jiangsu 213001 (China); Jiangsu Province Key Laboratory of Precious Metal Chemistry and Technology, Changzhou, Jiangsu 213001 (China); Zhou Quanfa [School of Chemistry and Chemical Engineering, Jiangsu Teachers' University of Technology, Changzhou, Jiangsu 213001 (China); Jiangsu Province Key Laboratory of Precious Metal Chemistry and Technology, Changzhou, Jiangsu 213001 (China)

2006-09-25

Uniform rod-like Sr{sub 2-x}Dy {sub x}CeO{sub 4} nano-phosphors with orthorhombic structure were prepared via a hydrothermal method, in the absence of any surfactant or template. The structure, morphology, particle size, and tunable luminescence properties of the samples were investigated by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED), UV-vis absorption and photoluminescence spectrum, respectively. The as-prepared phase-pure Sr{sub 2-x}Dy {sub x}CeO{sub 4} nanorods had the length of 50-150 nm and width of 80 nm. The Dy{sup 3+} ions emission in Sr{sub 2-x}Dy {sub x}CeO{sub 4} could be effectively excited through the energy absorbed by Sr{sub 2}CeO{sub 4} host. The tunable photoluminescence has been observed from Sr{sub 2}CeO{sub 4} doped with Dy{sup 3+} ions. Emission color of Sr{sub 2-x}Dy {sub x}CeO{sub 4} phosphor could be regulated from blue-white to white to yellow by adjusting the Dy{sup 3+} doping content in Sr{sub 2}CeO{sub 4} host, which originated from energy transfer between two different emission centers.

Spontaneous structural distortion of the metallic Shastry-Sutherland system Dy B4 by quadrupole-spin-lattice coupling

Science.gov (United States)

Sim, Hasung; Lee, Seongsu; Hong, Kun-Pyo; Jeong, Jaehong; Zhang, J. R.; Kamiyama, T.; Adroja, D. T.; Murray, C. A.; Thompson, S. P.; Iga, F.; Ji, S.; Khomskii, D.; Park, Je-Geun

2016-11-01

Dy B4 has a two-dimensional Shastry-Sutherland (Sh-S) lattice with strong Ising character of the Dy ions. Despite the intrinsic frustrations, it undergoes two successive transitions: a magnetic ordering at TN=20 K and a quadrupole ordering at TQ=12.5 K . From high-resolution neutron and synchrotron x-ray powder diffraction studies, we have obtained full structural information on this material in all phases and demonstrate that structural modifications occurring at quadrupolar transition lead to the lifting of frustrations inherent in the Sh-S model. Our paper thus provides a complete experimental picture of how the intrinsic frustration of the Sh-S lattice can be lifted by the coupling to quadrupole moments. We show that two other factors, i.e., strong spin-orbit coupling and long-range Ruderman-Kittel-Kasuya-Yosida (RKKY) interaction in metallic Dy B4 , play an important role in this behavior.

Combustion synthesis of Eu and Dy activated Sr3(VO4)2 phosphor ...

Indian Academy of Sciences (India)

phosphor as well as Sr3(VO4)2:Dy is blue and yellow emitting phosphor for solid state lighting i.e. white LEDs. The ... 2004; Pang et al 2004) doped with rare earth has expanded ... controlled since the LED light output (intensity and colour).

Environmental monitoring system with TLD

International Nuclear Information System (INIS)

Aguerre, L.; Carelli, J.; Gregori, B.

2006-01-01

Presently work the methodology used by the Laboratory of Thermoluminescent Dosimetry (TLD) of the Nuclear Regulatory Authority (RNA) to gauge it system of environmental monitoring in function of the media absorbed dose rate in free air and the environmental dose equivalent, H * (10), according to the recommendation ICRU Report 47 is described. It was studied the response of the environmental dosemeter (DA) in fields of photonic radiation of energies W60, Wl 10, W200 and 137 Cs. The irradiations were carried out following the recommendations of the standard ISO:4037. It was analyzed the response in the DA of the detectors LiF: Mg, Ti and CaF 2 : Dy for the different radiation qualities and the relative response at 137 Cs of both. The methodology used in the evaluation of the dose includes: the correction of the readings of both detectors by fading, gotten experimentally, the witness of transfers, the energy answer and the value of the zero. The dose is calculated applying the average pondered in uncertainty of the dose obtained for each type of detector. Its were analyzed and calculated the uncertainties that affect to the measurement following the recommendation of the Argentine standard IRAM 35050. The detection limit of the absorbed dose rate in free air of this system it is 3.5 n Gy/h for a period of sampling of 3 months. With this detection limit environmental dose equivalent rates of the order of 70 n Sv/h are measured with an expanded uncertainty of the order of 10% with a cover factor k = 2. (Author)

From a Dy(III) single molecule magnet (SMM) to a ferromagnetic [Mn(II)Dy(III)Mn(II)] trinuclear complex.

Science.gov (United States)

Bhunia, Asamanjoy; Gamer, Michael T; Ungur, Liviu; Chibotaru, Liviu F; Powell, Annie K; Lan, Yanhua; Roesky, Peter W; Menges, Fabian; Riehn, Christoph; Niedner-Schatteburg, Gereon

2012-09-17

The Schiff base compound 2,2'-{[(2-aminoethyl)imino]bis[2,1-ethanediyl-nitriloethylidyne]}bis-2-hydroxy-benzoic acid (H(4)L) as a proligand was prepared in situ. This proligand has three potential coordination pockets which make it possible to accommodate from one to three metal ions allowing for the possible formation of mono-, di-, and trinuclear complexes. Reaction of in situ prepared H(4)L with Dy(NO(3))(3)·5H(2)O resulted in the formation of a mononuclear complex [Dy(H(3)L)(2)](NO(3))·(EtOH)·8(H(2)O) (1), which shows SMM behavior. In contrast, reaction of in situ prepared H(4)L with Mn(ClO(4))(2)·6H(2)O and Dy(NO(3))(3)·5H(2)O in the presence of a base resulted in a trinuclear mixed 3d-4f complex (NHEt(3))(2)[Dy{Mn(L)}(2)](ClO(4))·2(H(2)O) (2). At low temperatures, compound 2 is a weak ferromagnet. Thus, the SMM behavior of compound 1 can be switched off by incorporating two Mn(II) ions in close proximity either side of the Dy(III). This quenching behavior is ascribed to the presence of the weak ferromagnetic interactions between the Mn(II) and Dy(III) ions, which at T > 2 K act as a fluctuating field causing the reversal of magnetization on the dysprosium ion. Mass spectrometric ion signals related to compounds 1 and 2 were both detected in positive and negative ion modes via electrospray ionization mass spectrometry. Hydrogen/deuterium exchange (HDX) reactions with ND(3) were performed in a FT-ICR Penning-trap mass spectrometer.

Differences in TLD 600 and TLD 700 glow curves derived from distict mixed gamma/neutron field irradiations

International Nuclear Information System (INIS)

Cavalieri, Tassio A.; Castro, Vinicius A.; Siqueira, Paulo T.D.

2013-01-01

In Neutron Capture Therapy, a thermal neutron beam shall impinge on a specific nuclide, such as 10 B, to promote a nuclear reaction which releases the useful therapeutic energy. A nuclear reactor is usually used as the neutron source, and therefore field contaminants such as gamma and high energy neutrons are also present in the field. However, mixed field dosimetry still stands as a challenge in some cases, due to the difficulty to experimentally discriminate the dose from each field component. For the mixed field dosimetry, the International Commission on Radiation end Units (ICRU) recommends the use of detector pairs with different responses for each beam component. The TLD 600/700 pair meets this need, because these LiF detectors have different Li isotopes concentration, with distinct thermal neutron responses because 6 Li presents a much higher neutron capture cross section than does 7 Li for low energy neutrons. TLD 600 is 6 Li enriched while TLD 700 is 7 Li enriched. However, depending on the neutron spectrum presented in the mixed field, TLD 700 response to thermal neutrons cannot be disregarded. This work aims to study the difference in TLD 600 and TLD 700 glow curves when these TLDs are submitted to mixed fields of different energy spectra and components balance. The TLDs were irradiated in a pure gamma source, and in mixed fields from an AmBe sealed source and from the IPEN/MB-01 reactor. These TLDs were read and had their two main dosimetric regions analyzed to observe the differences in the glow curves of these TLDs in each irradiation. Field components discrimination was achieved through Monte Carlo simulations run with MCNP radiation transport code. (author)

Work place monitoring in accelerator facilities using thermoluminescent dosimeters

International Nuclear Information System (INIS)

Ribeiro, M.S.; Sanches, M.P.; Osima, A.M.; Rodriguez, D.L.; Carvalho, R.N.; Somessari, R.N.

1998-01-01

The increase in the use of large amounts of energy and large particles accelerators in development or in industrial processes for the reticulation, polymerization and sterilization of cables and wires allowed to discover and monitor work places in facilities having particle accelerators at the Institute of Energy and Nuclear Inquiries Comissao National de Energy Nuclear. Measures previously taken by technicians in routine monitoring, show that radiation doses found in the beams tube and at the door of the accelerator area is high enough to require routine programs to monitor work places at the installation. That is why, fifteen thermoluminescent dosimeters (TLD) where placed in different points of the facility where doses must be measured along a three month period and at the same time readings must be taken from control dosimeters kept within a shielded container. The monitor had a small double layer with three pellets of TLD CaSO4 Dy inside of a route carrier adopted in routine workers dosimetry usually. Outcomes show that the radiological protection program must be implemented to ameliorate and guarantee safety procedures

Modification of beta dose evaluation algorithm for better accuracy in personnel monitoring

International Nuclear Information System (INIS)

Rakesh, R.B.; Kumar, Munish; Sneha, C.; Ratna, P.; Datta, D.

2016-01-01

Dose due to beta radiations is the main contributor to the skin dose. Assessment of individual dose (whole body, skin, extremity) in India is based on CaSO 4 :Dy based Teflon embedded TLD badge used for personnel monitoring. The design of the dosemeter enables identification of radiation type which, in turn, allows use of radiation specific algorithm for dose evaluation. The difference of response of three discs of the TLD badge to beta radiation in beta/beta-gamma fields is due to the presence of different filters corresponding to the three discs. The response of disc under metal filter (D 1 ) to beta being negligible while that of open disc (D 3 ) is the maximum. The ratio of response of open disc to that under Perspex (D 3 /D 2 ) to beta is highly dependent on its energy and angle of incidence. Therefore estimation of dose due to beta is based on response of open disc corrected for the energy of beta using D 3 /D 2

Personal exposure control using TLD

International Nuclear Information System (INIS)

Ishiguro, Hideharu; Takeda, Shinso

1979-01-01

In the Tokai Works of the Power Reactor and Nuclear Fuel Development Corporation (PNC), for personal exposure control, the switching from film badges to TLD badges (and also finger-ring type local dosimeters) was made in fiscal 1974. The facilities involved are a fuel reprocessing plant, a PuO 2 -UO 2 mixed fuel production facility, and a centrifugal uranium enrichment development facility. The types of radiation concerned are various, such as γ(x), β and n. The situation of personal exposure control with TLD and the dose evaluation methods for respective radiations are explained. The number of personnel subject to exposure control, including transient people, is about 2500 - 3000 per three months. The TLD badges used are a special PNC type with TLDs to measure separately γ(x), β and n. With casings made of ABS resin, the external dimensions are 76 mm x 46 mm. (J.P.N.)

Thermoluminescent response of CaSO{sub 4}: Dy + PTFE to beta particles; Respuesta termoluminiscente de CaSO{sub 4}: Dy + PTFE a particulas beta

Energy Technology Data Exchange (ETDEWEB)

Aguirre C, A.; Azorin N, J. [Colegio de Bachilleres No. 13, Xochimilco-Tepepan, 16000 Mexico D.F. (Mexico)

2000-07-01

In this work the results of studying the thermoluminescent properties of CaSO{sub 4}: Dy + PTFE are presented when it is irradiated with beta particles. The conclusion was the obtention of the Tl response curve in function of dose is that to desexcite the dosemeters at temperature 300 C during 30 minutes and after that were irradiated at different times in groups and to do the reading of dosemeter, it can be observed that a greater irradiation time major is the Tl response and this depends of the material has been used. (Author)

How to diagnose any type of TLD Reader?; Como diagnosticar cualquier tipo de TLD Reader?

Energy Technology Data Exchange (ETDEWEB)

Rodriguez, Manuel Lopez; Garcia, Jose A. Tamayo; Gil, Alex Vergara; Lores, Stefan Gutierrez; Acosta, Andry Romero; Villanueva, Gilberto Alonso, E-mail: manolo@cphr.edu.cu, E-mail: jotag@cphr.edu.cu, E-mail: alex@cphr.edu.cu, E-mail: stefan@cphr.edu.cu, E-mail: andy@cphr.edu.cu, E-mail: gilberto@cphr.edu.cu [Centro de Proteccion e Higiene de las Radiaciones (CPHR), La Habana (Cuba)

2013-07-01

The acquisition of know how of practical experiences obtained in the repair and maintenance of readers TLD RADOS for five years of work and the request by the International Atomic Energy for signing new Research Contracts (CRP), made possible the CRP 13328, in which the specialist is committed in the course of a year, to deliver educational software in order to train personnel associated with the operation of the TLD readers RADOS. Due to the importance of continuous transfer of knowledge for new generations of technicians and specialists who join our laboratories, the idea came when the first interactive CD that grouped 19 videos, divided into three blocks was ready: learning, repair and maintenance; it was suggested to expand the training for any TLD reader. Thus a much more complete than the first version package emerged. 7 cases were subsequently published in an IAEA TECDOC, 1599 were included.

Neutron dose measurements of Varian and Elekta linacs by TLD600 and TLD700 dosimeters and comparison with MCNP calculations.

Science.gov (United States)

Nedaie, Hassan Ali; Darestani, Hoda; Banaee, Nooshin; Shagholi, Negin; Mohammadi, Kheirollah; Shahvar, Arjang; Bayat, Esmaeel

2014-01-01

High-energy linacs produce secondary particles such as neutrons (photoneutron production). The neutrons have the important role during treatment with high energy photons in terms of protection and dose escalation. In this work, neutron dose equivalents of 18 MV Varian and Elekta accelerators are measured by thermoluminescent dosimeter (TLD) 600 and TLD700 detectors and compared with the Monte Carlo calculations. For neutron and photon dose discrimination, first TLDs were calibrated separately by gamma and neutron doses. Gamma calibration was carried out in two procedures; by standard 60Co source and by 18 MV linac photon beam. For neutron calibration by (241)Am-Be source, irradiations were performed in several different time intervals. The Varian and Elekta linac heads and the phantom were simulated by the MCNPX code (v. 2.5). Neutron dose equivalent was calculated in the central axis, on the phantom surface and depths of 1, 2, 3.3, 4, 5, and 6 cm. The maximum photoneutron dose equivalents which calculated by the MCNPX code were 7.06 and 2.37 mSv.Gy(-1) for Varian and Elekta accelerators, respectively, in comparison with 50 and 44 mSv.Gy(-1) achieved by TLDs. All the results showed more photoneutron production in Varian accelerator compared to Elekta. According to the results, it seems that TLD600 and TLD700 pairs are not suitable dosimeters for neutron dosimetry inside the linac field due to high photon flux, while MCNPX code is an appropriate alternative for studying photoneutron production.

Luminescence studies on Dy3+ and Dy3+:Eu3+ co-doped boro-phosphate glasses for WLED applications

Science.gov (United States)

Vijayakumar, M.; Uma, V.; Arunkumar, S.; Marimuthu, K.

2015-06-01

Dy3+ and Dy3+:Eu3+ co-doped boro-phosphate glasses have been prepared and optically characterized using absorption, luminescence and decay measurements. The Nephelauxetic ratios (β), Bonding parameters (δ) and Judd-Ofelt (JO) intensity parameters Ωλ (λ = 2, 4 and 6) were calculated to study the nature of the environment around the RE3+ ions in the prepared glasses. The yellow to blue (Y/B) intensity ratio and the chromaticity color coordinates were calculated from the luminescence measurements. The lifetimes of the 4F9/2 excited level were measured using decay curves and is found to decrease in the Dy3+:Eu3+ co-doped glass due to the occurrence of resonant energy transfer between Dy3+-Eu3+ ions and the non-exponential decay rates have been fitted with Inokuti-Hirayama (IH) model. The decay curves are well fitted for S= 6 suggesting that the interaction between active ions for the energy transfer is of dipole-dipole nature.

Magnetic properties of the ternary carbide DyCoC2 studied by magnetization measurements, neutron diffraction and 161Dy Moessbauer spectroscopy

International Nuclear Information System (INIS)

Amanai, H.; Onodera, H.; Ohashi, M.; Matsuo, S.; Yamauchi, H.

1995-01-01

The magnetic properties of DyCoC 2 have been investigated by means of magnetization measurements, powder neutron diffraction and 161 Dy Moessbauer spectroscopy. The magnetization versus temperature curves of a single-crystalline sample reveal that the magnetic structure of DyCoC 2 is a simple collinear ferromagnetic one below T C =10.0 K. At 4.2 K, the magnitude of the Dy moment is 8.7(1)μ B , whose direction is defined by an angle of 38.0(5) from the a-axis toward the c-axis. The magnetic structure and the magnitude of the moment are also confirmed by the results of powder neutron diffraction experiments and 161 Dy Moessbauer spectroscopy, respectively. ((orig.))

TL dosimetric characterization of gamma irradiated SrSO{sub 4}:Eu phosphors

Energy Technology Data Exchange (ETDEWEB)

Jayasudha, S., E-mail: jsnair.india@gmail.com [Mahatma Gandhi College, Kesavadasapuram, Pattom Palace P.O., Thiruvananthapuram 695004 (India); Madhukumar, K.; Nair, C.M.K.; Nair, Resmi G. [Mahatma Gandhi College, Kesavadasapuram, Pattom Palace P.O., Thiruvananthapuram 695004 (India); Rajesh, S. [Department of Materials & Ceramic Engineering, University of Aveiro, Aveiro 3810-193 (Portugal); Elias, T.S. [State Institute of Cancer Research, Medical College P.O., Thiruvananthapuram 695011 (India); Anandakumar, V.M. [Mahatma Gandhi College, Kesavadasapuram, Pattom Palace P.O., Thiruvananthapuram 695004 (India); State Institute of Cancer Research, Medical College P.O., Thiruvananthapuram 695011 (India); Department of Materials & Ceramic Engineering, University of Aveiro, Aveiro 3810-193 (Portugal); Gopakumar, N. [Mahatma Gandhi College, Kesavadasapuram, Pattom Palace P.O., Thiruvananthapuram 695004 (India)

2017-03-15

Thermoluminescence (TL) characteristics of SrSO{sub 4}:Eu nanostructured phosphor under gamma excitation has been studied and their suitability for environmental radiation dosimetry applications is discussed. The dopant level is tuned for optimum TL response. The effect of radiation dose and heating rate were investigated. The phosphor preserves linearity in the low dose region, 0.1 Gy to 20 Gy. PL studies of irradiated and un-irradiated phosphors reveal that the dopant Eu exists in divalent state and are the luminescence emission centres in the material. The fading properties of SrSO{sub 4}:Eu phosphor are observed to be better than that of the commercial dosimeters TLD-200 and TLD-400. The kinetic parameters are calculated using Chen's method and initial rise method and verified by Computerized Glow curve Deconvolution (CGCD). The sensitivity of the synthesized phosphor is found to be very high when compared with that of the commercial standard dosimeter CaSO{sub 4}:Dy. The phosphor is found to be stable for short term radiation monitoring.

Series of isostructural planar lanthanide complexes [Ln(III)4(mu3-OH)2(mdeaH)2(piv)8] with single molecule magnet behavior for the Dy4 analogue.

Science.gov (United States)

Abbas, Ghulam; Lan, Yanhua; Kostakis, George E; Wernsdorfer, Wolfgang; Anson, Christopher E; Powell, Annie K

2010-09-06

A series of five isostructural tetranuclear lanthanide complexes of formula [Ln(4)(mu(3)-OH)(2)(mdeaH)(2)(piv)(8)], (mdeaH(2) = N-methyldiethanolamine; piv = pivalate; Ln = Tb (1), Dy (2), Ho (3), Er (4), and Tm (5)) have been synthesized and characterized. These clusters have a planar "butterfly" Ln(4) core. Magnetically, the Ln(III) ions are weakly coupled in all cases; the Dy(4) compound 2 shows Single Molecule Magnet (SMM) behavior.

K{sub 2}Y(WO{sub 4})(PO{sub 4}): Tm{sup 3+}, Dy{sup 3+}: a potential tunable single-phased white-emitting phosphor under UV light excitation

Energy Technology Data Exchange (ETDEWEB)

Han, Lili, E-mail: hanlili.06@163.com [Key Laboratory of Atomic and Molecular Physics & Functional Materials of Gansu Province, College of Physics and Electronic Engineering, Northwest Normal University, Lanzhou 730070 (China); Xie, Xinzhong; Lian, Junhong; Wang, Yuhua [Department of Material Science, School of Physical Science and Technology, Lanzhou University, Lanzhou 730000 (China); Wang, Chengwei, E-mail: cwwang@nwnu.edu.cn [Key Laboratory of Atomic and Molecular Physics & Functional Materials of Gansu Province, College of Physics and Electronic Engineering, Northwest Normal University, Lanzhou 730070 (China)

2016-08-15

A white-emitting K{sub 2}Y(WO{sub 4})(PO{sub 4}): Tm{sup 3+}, Dy{sup 3+} phosphor has been successfully prepared by conventional high-temperature solid-state reaction. X-ray diffraction and photoluminescence spectra were used to characterize the as-synthesized phosphors. The results show that all samples crystallize in an orthorhombic crystal system with a space group of Ibca (73). Under the excitation at 292 nm, the un-doped sample presents a self-illumination feature, which should result from the crystal host excitation or molecular transitions within the WO{sub 4}{sup 2−} group. Upon 360 or 350 nm excitation, the Tm{sup 3+}or Dy{sup 3+} single-doped K{sub 2}Y(WO{sub 4})(PO{sub 4}) samples can emit an intense blue and white light with the optimal concentration 1% and 5%, respectively. In order to inquiry the interactions of Tm{sup 3+} and Dy{sup 3+}, a series of co-doping samples were prepared and by the analyses of excitation and emission spectra and decay times, we carefully investigated whether or not the energy transfer occurs between Tm{sup 3+} and Dy{sup 3+} in the host K{sub 2}Y(WO{sub 4})(PO{sub 4}). In addition, the color coordinate of as-obtained samples pumped by ultraviolet light are also clearly displayed in this work. Furthermore, with the increase in temperature, KYWP: 0.05Dy{sup 3+} presents satisfactory thermal stability. All the results indicate that the single-composition phosphor could have a promising application in the area of white light emitting diodes.

Luminescence and energy transfer of Tm3+ or/and Dy3+ co-doped in Sr3Y(PO4)3 phosphors with UV excitation for WLEDs

International Nuclear Information System (INIS)

Wang, Jiyou; Wang, Jianbo; Duan, Ping

2014-01-01

Powder samples Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ -yDy 3+ were synthesized by the conventional solid-state reaction method. By appropriate tuning of activator content, the emission color can be adjusted around blue to white and yellow. It was discovered that the energy transfer from Tm 3+ to Dy 3+ was demonstrated to be via the intensity of Dy 3+ emission increase with the increase of Tm 3+ concentration. By changing the doping concentration of Tm 3+ and Dy 3+ in Sr 3 Y(PO 4 ) 3 , white-emitting phosphors are produced by 350 nm excitation wavelength, their corresponding color coordinates are very close to the white color chromaticity coordinates (x=0.33, y=0.33). Finally, Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ −yDy 3+ phosphors could be a good promising single-component white light-emitting UV-convertible phosphor in the field of white LEDs. -- Highlights: • The Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ −yDy 3+ phosphors were synthesized by the conventional solid-state reaction method. • The energy transfer in between Tm 3+ and Dy 3+ was observed and explained. • The phosphors can be efficiently excited by a UV light. • The Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ -yDy 3+ phosphor could be a better candidate white phosphor for UV W-LEDs

Photoluminescence characterization of Dy3+ and Eu2+ ion in M5(PO4)3F (M = Ba, Sr, Ca) phosphors

International Nuclear Information System (INIS)

Nagpure, I.M.; Shinde, K.N.; Dhoble, S.J.; Kumar, Animesh

2009-01-01

Photoluminescence investigation of Eu and Dy activated phosphate based phosphors prepared by combustion synthesis, characterized by XRD (X-ray diffraction) and photoluminescence techniques, has been reported. PL excitation spectrum of M 5 (PO 4 ) 3 F:Dy phosphors shows the excitation peaks ranging from 300 to 400 nm due to 4f → 4f transitions of Dy 3+ ions. PL emission spectrum of Dy 3+ ion under 348 nm excitation gives PL emission at 482 nm (blue) due to 4 F 9/2 → 6 H 15/2 transitions, 574 nm (yellow) emission due to 4 F 9/2 → 6 H 13/2 transitions and 670 nm (red) due to 4 F 9/2 → 6 H 11/2 transitions, gives BYR (blue-yellow-red) emissions. The Eu 2+ broad band PL emission spectrum was observed in M 5 (PO 4 ) 3 F:Eu phosphor at 440 nm in the blue region of the spectrum due to 5d → 4f transition at 352 nm excitation. The 300-400 nm is Hg-free excitation (Hg excitation is 85% 254 nm wavelength of light and 15% other wavelengths), which is characteristic of solid-state lighting phosphors. Hence PL emission in divalent europium and trivalent dysprosium may be efficient photoluminescent materials for solid-state lighting phosphors.

The photoluminescent property and optical transition analysis of host sensitized Ca{sub 0.5}Sr{sub 0.5}MoO{sub 4}:Dy{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Yang, Zhiping; Hou, Chuncai [College of Physics and Technology, Hebei University, Baoding, Hebei 071002 (China); Duan, Guangjie [College of Electronics and Information Engineering, Hebei University, Baoding, Hebei 071002 (China); Yang, Fu [College of Physics and Technology, Hebei University, Baoding, Hebei 071002 (China); College of Science, Hebei North University, Zhangjiakou 075000 (China); Liu, Pengfei; Wang, Can [College of Physics and Technology, Hebei University, Baoding, Hebei 071002 (China); Liu, Lipeng [College of Electronics and Information Engineering, Hebei University, Baoding, Hebei 071002 (China); Dong, Guoyi, E-mail: dongguoyitxzz@163.com [College of Physics and Technology, Hebei University, Baoding, Hebei 071002 (China)

2014-08-01

Highlights: • A novel host sensitized Ca{sub 0.5−x}Sr{sub 0.5}MoO{sub 4}:xDy{sup 3+} phosphors could be synthesized by solid state reaction. • The XRD and SEM figures were made to analyze the crystal phase and morphology of Ca{sub 0.5−x}Sr{sub 0.5}MoO{sub 4}:xDy{sup 3+} phosphors. • We research the emission and excitation properties by analyzing the relevant optical transition. • The energy transition is proved to exist by the analysis on luminescence spectra and luminescence decay curves. • The chromaticity coordinate of Ca{sub 0.5−x}Sr{sub 0.5}MoO{sub 4}:xDy{sup 3+} will be tunable as changing x. - Abstract: A series of Dy{sup 3+} doped Ca{sub 0.5}Sr{sub 0.5}MoO{sub 4} phosphors were synthesized by solid state reaction. The structure and the photoluminescent (PL) properties of the as-prepared powders were characterized by X-ray diffraction (XRD), field emission scanning electron microscope and fluorescent spectrophotometry. The analyses on optical transition of Ca{sub 0.5}Sr{sub 0.5}MoO{sub 4}:xDy{sup 3+} phosphors indicate that the broad band of excitation spectrum comes from the charge transmission. The broad band of excitation spectrum matches well with the excitation energy level of Dy{sup 3+}, indicating the energy transfer from the host to Dy{sup 3+}. The chromaticity coordinates changed from blue–green to yellow area depending on the Dy{sup 3+} concentration. In addition, the main mechanism of the concentration quenching was the electric multiple interaction between Dy{sup 3+} ions.

Mechanical and corrosion properties of binary Mg–Dy alloys for medical applications

International Nuclear Information System (INIS)

Yang Lei; Huang Yuanding; Peng Qiuming; Feyerabend, Frank; Kainer, Karl Ulrich; Willumeit, Regine; Hort, Norbert

2011-01-01

Microstructure, mechanical and corrosion properties of binary magnesium–dysprosium (Mg-5, 10, 15, 20 wt.% Dy) alloys were investigated for medical applications. In the as-cast condition, the distribution of Dy is quite inhomogeneous. Mg–10Dy alloy exhibits a moderate tensile and compression yield strength, and the best elongation and corrosion resistance. After T4 (solutionizing) treatment, the distribution of Dy becomes homogeneous. The tensile and compression yield strength of all Mg–Dy alloys decreases. The elongation remains unchanged, while the corrosion resistance is largely improved after T4 treatment.

Mechanical and corrosion properties of binary Mg-Dy alloys for medical applications

Energy Technology Data Exchange (ETDEWEB)

Yang Lei, E-mail: lei.yang@hzg.de [Helmholtz-Zentrum Geesthacht, Institute of Materials Research, Max-Planck-Str. 1, D-21502 Geesthacht (Germany); Yuanding, Huang; Qiuming, Peng; Feyerabend, Frank; Kainer, Karl Ulrich; Willumeit, Regine; Hort, Norbert [Helmholtz-Zentrum Geesthacht, Institute of Materials Research, Max-Planck-Str. 1, D-21502 Geesthacht (Germany)

2011-12-15

Microstructure, mechanical and corrosion properties of binary magnesium-dysprosium (Mg-5, 10, 15, 20 wt.% Dy) alloys were investigated for medical applications. In the as-cast condition, the distribution of Dy is quite inhomogeneous. Mg-10Dy alloy exhibits a moderate tensile and compression yield strength, and the best elongation and corrosion resistance. After T4 (solutionizing) treatment, the distribution of Dy becomes homogeneous. The tensile and compression yield strength of all Mg-Dy alloys decreases. The elongation remains unchanged, while the corrosion resistance is largely improved after T4 treatment.

2.4 μm diode-pumped Dy2+:CaF2 laser

Science.gov (United States)

Švejkar, Richard; Papashvili, Alexander G.; Šulc, Jan; Němec, Michal; Jelínková, Helena; Doroshenko, Maxim E.; Batygov, Sergei H.; Osiko, Vyacheslav V.

2018-01-01

In this work, a cryogenic cooled, longitudinal diode-pumped Dy2+ :CaF2 laser was investigated for the first time. The temperature dependence of the spectroscopy and the laser properties of Dy2+ :CaF2 are presented. The tested Dy2+ :CaF2 crystal was a longitudinal pump in a near-IR region (926 nm) by laser diode radiation. The maximal mean output power and slope efficiency at 78 K during the pulse regime of the laser were 57.5 mW and 7%, respectively. Furthermore, the CW regime was successfully tested and a maximum output power of 0.37 W was obtained for the absorbed pumping power 5.7 W. The emission laser wavelength was 2367 nm.

Quadrupolar frustration in shastry-sutherland lattice of DyB4 studied by resonant x-ray scattering

International Nuclear Information System (INIS)

Okuyama, Daisuke; Matsumura, Takeshi; Nakao, Hironori; Murakami, Youichi

2005-01-01

We have observed geometrical frustration of quadrupolar and magnetic moments in dysprosium tetraboride, DyB 4 , where the rare-earth sites form a Shastry-Sutherland lattice. Resonant X-ray scattering at the L III absorption edge of Dy was utilized. Analysis of the energy, polarization, temperature, and azimuthal-angle dependences of the E1 resonance of the (100) forbidden reflection show that the magnetic and quadrupolar components within the frustrated c plane have a short-range correlation, suggesting that the moments are fluctuating. In contrast, the basic antiferromagnetic component along the c-axis has a long-range order. (author)

The IAEA/WHO TLD postal programme for radiotherapy hospitals

International Nuclear Information System (INIS)

Izewska, J.; Andreo, P.

2000-01-01

Since 1969 the International Atomic Energy Agency (IAEA), together with the World Health Organization (WHO), has performed postal TLD audits to verify the calibration of radiotherapy beams in developing countries. A number of changes have recently been implemented to improve the efficiency of the IAEA/WHO TLD programme. The IAEA has increased the number of participants and reduced significantly the total turn-around time to provide results to the hospitals within the shortest possible time following the TLD irradiations. The IAEA has established a regular follow-up programme for hospitals with results outside acceptance limits of ±5%. The IAEA has, over 30 years, verified the calibration of more than 3300 clinical photon beams at approximately 1000 radiotherapy hospitals. Only 65% of those hospitals who receive TLDs for the first time have results within the acceptance limits, while more than 80% of the users that have benefited from a previous TLD audit are successful. The experience of the IAEA in TLD audits has been transferred to the national level. The IAEA offers a standardized TLD methodology, provides Guidelines and gives technical back-up to the national TLD networks. The unsatisfactory status of the dosimetry for radiotherapy, as noted in the past, is gradually improving however, the dosimetry practices in many hospitals in developing countries need to be revised in order to reach adequate conformity to hospitals that perform modern radiotherapy in Europe, USA and Australia. (author)

Dosimetric quality control in radiotherapy using TLD methodology

International Nuclear Information System (INIS)

Saravi, M.C.; Kessler, C.; Alvarez, P.E.; Feld, D.B.

2002-01-01

In the frame of the IAEA Co-ordinated Research Project 'Development of a Quality Assurance Program for Radiation Therapy Dosimetry in Developing Countries' a Dosimetric Quality Control Group was set up in Argentina in 1996, to develop a program in order to improve radiotherapy in the country. Nowadays, this Group, briefly called External Audit Group (EAG), is composed by the national Secondary Standard Dosimetry Laboratory (SSDL), which has the responsibility for dose determinations, traceability to international dosimetry chain and TLD measurements, and two Medical Physicists from CNEA who are working at the Oncology Hospital 'Marie Curie' in Buenos Aires. The present paper reports the activities performed by the EAG with external high energy photon beams in reference conditions and the results of two pilot studies on cobalt 60 beams in non-reference conditions. The first step of the program was to update the existing data base about the radiotherapy centres operating in the country. A form was sent to each of them in order to obtain basic information about their staff, number and type of treatment machines, brachytherapy sources, measuring devices, beam calibration, treatment planning system, simulator and other relevant data. 90 radiotherapy centres were registered in the EAG data base. Forms were completed by 75/90 centres. There are nowadays 69 cobalt 60 units and 42 LINACs operating in the country (18/42 LINACs producing high energy X ray and electron beams). EAG deals with measurements performed with mailed TLD irradiated at radiotherapy centres. Internal quality control on our TLD system is made during each audit by means of reference capsules irradiated by IAEA; external controls consist in blind tests performed by IAEA once a year. The correction factor, K en , determined at our SSDL for high energy X-rays was checked with the collaboration of IAEA and Prague National Radiation Protection Institute (PNRPI) by means of a blind test. Results for 4 MV, 6 MV

Single-phase and warm white-light-emitting phosphors CaLa{sub 2−x−y}(MoO{sub 4}){sub 4}: xDy{sup 3+}, yEu{sup 3+}: Synthesis, luminescence and energy transfer

Energy Technology Data Exchange (ETDEWEB)

Han, Li; Liu, Guixia, E-mail: liuguixia22@163.com; Dong, Xiangting; Wang, Jinxian; Yu, Wensheng

2016-10-15

A series of single-phase warm white light emitting CaLa{sub 2−x−y}(MoO{sub 4}){sub 4}: xDy{sup 3+}, yEu{sup 3+} phosphors were synthesized by a typical sol–gel method. X-ray diffraction (XRD) analysis reveals that the crystal structures of the samples are matched well with the tetragonal CaMoO{sub 4}. Upon ultraviolet (UV) light radiation, the Dy{sup 3+} or Eu{sup 3+} ions singly activated CaLa{sub 2}(MoO{sub 4}){sub 4} phosphors exhibit corresponding emissions originated from the f–f transitions of Dy{sup 3+} or Eu{sup 3+} ions. Under near ultraviolet (n-UV) light excitation, in the Dy{sup 3+} and Eu{sup 3+} ions co-doped samples, the energy transfer (ET) phenomenon from Dy{sup 3+} to Eu{sup 3+} ions can be observed and has been demonstrated to be a quadrupole–quadrupole interaction mechanism. The emission color of CaLa{sub 1.98−y}(MoO{sub 4}){sub 4}: 0.02Dy{sup 3+}, yEu{sup 3+} samples can be tuned from cool to warm white light by adjusting the concentration of Eu{sup 3+} ions. In addition, it can be found that CaLa{sub 1.974}(MoO{sub 4}){sub 4}: 0.02Dy{sup 3+}, 0.006Eu{sup 3+} samples emit bright white light with the CIE coordinate of (0.348, 0.313) and the color temperature of 5087 K, which is very close to the standard white light. All the results demonstrate that the as-synthesized phosphors have great potential applications in the field of n-UV white light emitting diodes (WLEDs).

Heterogeneous bilayer films NiFe (Fe)-Dy: magnetic circular dichroism and Dy spin ordering

Energy Technology Data Exchange (ETDEWEB)

Markov, V.V. E-mail: ise@iph.krasn.ruise@iph.krasnoyarsk.su; Kesler, V.G.; Khudyakov, A.E.; Edelman, I.S.; Bondarenko, G.V

2001-08-01

Results of the magnetic circular dichroism (MCD) and Auger electron spectroscopy (AES) investigations in the 3d transition metal-Dy bi-layer films are presented. It is shown that even at room temperature the Dy layer makes a contribution to MCD of the bi-layer film, which corresponds to the MCD value in the single-layer Dy film measured below T{sub C}=85 K. According to the AES data there is no sharp interface between 3d and Dy layers in these films. Some amount of Ni and Fe atoms is dispersed in the Dy layer and some amount of Dy atoms is dispersed in the 3d layer. The comparison of the MCD and AES data allows one to suppose the Dy layer in the bi-layer films to be magnetically ordered at room temperature under the influence of the 3d-layer spin system. The influence spreads to long distances inside Dy layer through the 3d-ions dispersed in it.

Heterogeneous bilayer films NiFe (Fe)-Dy: magnetic circular dichroism and Dy spin ordering

International Nuclear Information System (INIS)

Markov, V.V.; Kesler, V.G.; Khudyakov, A.E.; Edelman, I.S.; Bondarenko, G.V.

2001-01-01

Results of the magnetic circular dichroism (MCD) and Auger electron spectroscopy (AES) investigations in the 3d transition metal-Dy bi-layer films are presented. It is shown that even at room temperature the Dy layer makes a contribution to MCD of the bi-layer film, which corresponds to the MCD value in the single-layer Dy film measured below T C =85 K. According to the AES data there is no sharp interface between 3d and Dy layers in these films. Some amount of Ni and Fe atoms is dispersed in the Dy layer and some amount of Dy atoms is dispersed in the 3d layer. The comparison of the MCD and AES data allows one to suppose the Dy layer in the bi-layer films to be magnetically ordered at room temperature under the influence of the 3d-layer spin system. The influence spreads to long distances inside Dy layer through the 3d-ions dispersed in it

Tunable emission in Ln3+ (Ce3+/Dy3+, Ce3+/Tb3+) doped KNa3Al4Si4O16 phosphor synthesized by combustion method

Science.gov (United States)

Kolte, M. M.; Pawade, V. B.; Bhattacharya, A. B.; Dhoble, S. J.

2018-05-01

Ln3+ (Ln = Ce3+/Dy3+, Ce3+/Tb3+) doped KNa3Al4Si4O16 phosphor has been synthesized by Combustion method (CS) at 550° C successfully. Ln3+ (Ln = Ce3+, Dy3+, Tb3+) ions when doped in KNa3Al4Si4O16 host lattice, it shows blue and green emission band under the near Ultraviolet (NUV) excitation wavelength. The Photoluminescence excitation (PLE) and emission spectra are observed due to f-f and d-f transition of rare earth ions. Also, an effective energy transfer (ET) study from Ce3+ → Dy3+ and Ce3+ → Tb3+ ions has been studied and confirmed on the basis of Dexter-Foster theory. Further synthesized phosphor is well characterized by XRD, SEM, TEM and decay time measurement. However, the analysis of crystallite size, lattice strain has been studied by using theoretical as well as experimental techniques. Hence, the observed tunable emission in Ln3+ doped KNa3Al4Si4O16 phosphor may be applicable for solid state lighting technology.

Measurement of TLD Albedo response on various calibration phantoms

International Nuclear Information System (INIS)

Momose, T.; Tsujimura, N.; Shinohara, K.; Ishiguro, H.; Nakamura, T.

1996-01-01

The International Commission on Radiation Units and Measurements (ICRU) has recommended that individual dosemeter should be calibrated on a suitable phantom and has pointed out that the calibration factor of a neutron dosemeter is strongly influenced by the the exact size and shape of the body and the phantom to which the dosemeter is attached. As the principle of an albedo type thermoluminescent personal dosemeter (albedo TLD) is essentially based on a detection of scattered and moderated neutron from a human body, the sensitivity of albedo TLD is strongly influenced by the incident neutron energy and the calibration phantom. (1) Therefore for albedo type thermoluminescent personal dosemeter (albedo TLD), the information of neutron albedo response on the calibration phantom is important for appropriate dose estimation. In order to investigate the effect of phantom type on the reading of the albedo TLD, measurement of the TLD energy response and angular response on some typical calibration phantoms was performed using dynamitron accelerator and 252 Cf neutron source. (author)

A new fully automated TLD badge reader

International Nuclear Information System (INIS)

Kannan, S.; Ratna, P.; Kulkarni, M.S.

2003-01-01

At present personnel monitoring in India is being carried out using a number of manual and semiautomatic TLD badge Readers and the BARC TL dosimeter badge designed during 1970. Of late the manual TLD badge readers are almost completely replaced by semiautomatic readers with a number of performance improvements like use of hot gas heating to reduce the readout time considerably. PC based design with storage of glow curve for every dosimeter, on-line dose computation and printout of dose reports, etc. However the semiautomatic system suffers from the lack of a machine readable ID code on the badge and the physical design of the dosimeter card not readily compatible for automation. This paper describes a fully automated TLD badge Reader developed in the RSS Division, using a new TLD badge with machine readable ID code. The new PC based reader has a built-in reader for reading the ID code, in the form of an array of holes, on the dosimeter card. The reader has a number of self-diagnostic features to ensure a high degree of reliability. (author)

Combustion synthesis of Eu 2+ and Dy 3+ activated Sr 3 (VO 4 ) 2 ...

Indian Academy of Sciences (India)

2:Eu,Dy phosphors are presented in this paper. PL emission of Sr3(VO4)2:Eu phosphor shows green broad emission band centring at 511 nm and a red sharp band at 614 nm by excitation wavelength of 342 nm. The PL emission spectrum of ...

Phosphorescent and thermoluminescent properties of SrAl2O4:Eu2+, Dy3+ phosphors prepared by solid state reaction method

International Nuclear Information System (INIS)

Mothudi, B.M.; Ntwaeaborwa, O.M.; Kumar, A.; Sohn, K.; Swart, H.C.

2012-01-01

Long persistent SrAl 2 O 4 :Eu 2+ phosphors co-doped with Dy 3+ were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl 2 O 4 were observed in all the samples. The broad band emission spectra at 497 nm for SrAl 2 O 4 :Eu 2+ , Dy 3+ were observed and the emission is attributed to the 4f 6 5d 1 to 4f 7 transition of Eu 2+ ions. The samples annealed at 1100–1200 °C showed similar broad TL glow curves centered at 120 °C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy 3+ ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.

Experimental determination of the photon-energy dependent dose-to-water response of TLD600 and TLD700 (LiF:Mg,Ti) thermoluminescence detectors

Energy Technology Data Exchange (ETDEWEB)

Schwahofer, Andrea [Vivantes Clinic Neukoelln, Berlin (Germany). Dept. of Radiation Therapy; German Cancer Research Center, Heidelberg (Germany). Medical Physics in Radiation Therapy; Feist, Harald [Munich Univ. (Germany). Dept. of Radiation Therapy; Georg, Holger [PTW Freiburg (Germany). Calibration Lab.; Haering, Peter; Schlegel, Wolfgang [German Cancer Research Center, Heidelberg (Germany). Medical Physics in Radiation Therapy

2017-05-01

The aim of this study has been the experimental determination of the energy dependent dose-to-water response of TLD600 and TLD700 thermoluminescent detectors (Harshaw) in X-ray beams with mean photon energies from about 20 to 200 keV in comparison with {sup 60}Co gamma rays and 6 MV X-rays. Experiments were carried out in collaboration with the German secondary standard laboratory PTW Freiburg. The energy dependent relative responses of TLD600 and TLD700 thermoluminescence detectors were determined at radiation qualities between 30 kV{sub p} and 280 kV{sub p}. The overall uncertainty of the measured values was characterized by standard deviations varying from 1.2 to 3%. The present results agree with previous studies on the energy dependent dose-to-water response of TLD100. As an application example, the results were used to measure doses associated with X-ray imaging in image-guided radiotherapy.

Use of MCNP to compare the response of dose deposited in the TLD 100, TLD 600 and TLD 700 in radiation fields due to {sup 60}Co and {sup 241}AmBe source; Uso do MCNP para comparacao das respostas de dose depositada nos TLD 100, TLD 600 e TLD 700 em campos de irradiacao devido a fontes de {sup 60}Co e {sup 241}AmBe

Energy Technology Data Exchange (ETDEWEB)

Cavalieri, Tassio A.; Castro, Vinicius A.; Siqueira, Paulo T.D., E-mail: tassio.cavalieri@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2012-08-15

The successes of Boron Neutron Capture Therapy (BNCT) depend on the ability to deliver an adequate irradiation field to the target cells. Neutron beams used in BNCT are mostly driven from reactors and therefore, not only have a neutron energy range which far exceeds the thermal region but also do have a great gamma component. Beam characterization and dosimetry are consequently one of the essential procedures to be overcome to properly apply this technique. One of the methods currently used in mixed field (field containing both neutron and gamma) characterization, lies on the use of a pair of detectors with distinct responses to each beam component. But this technique needs to be better understood of how each thermoluminescent dosimeter (TLD) behaves in a mixed field or in a pure field. This work presents the results of a set of simulations performed in order to analyze the response of three ordinary types of TLDs - TLD 100, TLD 600 and TLD 700 - submitted to different irradiation fields from a Cobalt source and an Americium-Beryllium source inside a paraffin disk. And is also a possible method for performing the selection and calibration of theses TLDs. (author)

Sol–gel synthesis and photoluminescence studies on colour tuneable Dy3+/Tm3+ co-doped NaGd(WO4)2 phosphor for white light emission

International Nuclear Information System (INIS)

Durairajan, A.; Balaji, D.; Rasu, K. Kavi; Moorthy Babu, S.; Hayakawa, Y.; Valente, M.A.

2015-01-01

A series of Dy 3+ /Tm 3+ ion co-doped NaGd(WO 4 ) 2 (NGW) phosphors were synthesised by a sol–gel method at low temperature for white light emission. The structural and luminescence properties of the synthesised phosphors were studied by powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Raman and photoluminescence techniques. In Dy 3+ /Tm 3+ :NGW phosphors, the dopant ions substituted Gd 3+ ions that are located in S 4 sites of NGW host lattice. In NGW host, under UV excitation the Dy 3+ ions have shown strong yellow ( 4 F 9/2 → 6 H 13/2 ) and comparatively weak blue ( 4 F 9/2 → 6 H 15/2 ) emission transitions at 575 and 488 nm, respectively. Due to deficient blue colour the overall emission falls in yellow region. Hence, Tm 3+ ions having strong blue emission at 455 nm corresponding to the transition 1 D 2 → 3 F 4 were co-activated along with Dy 3+ ions in NGW matrix. By changing the doping concentrations of Tm 3+ and Dy 3+ ions in NGW, white light emission was tuned by 353 nm excitation wavelength. Their corresponding colour co-ordinates were calculated and found to be very close to the white colour chromaticity co-ordinates (0.333, 0.333). - Highlights: • Dy 3+ and Dy 3+ /Tm 3+ :NGW phosphors were synthesised by sol–gel methods. • The excitation spectrum confirmed the strong absorption in near-UV region. • The emission spectrum shows the yellow and white emission to doped and co-doped phosphors respectively. • The CIE co-ordinate conforms close to daylight emission

Personnel dose equivalent monitoring at SLAC using lithium-fluoride TLD's [thermoluminescent dosimeters

International Nuclear Information System (INIS)

Jenkins, T.M.; Busick, D.D.

1987-03-01

TLD's replaced film badges in the early 1970's for all dose equivalent monitoring, both neutron and photon, and for all locations at SLAC. The photon TLD's, composed of Li-7 loaded teflon discs, are calibrated using conventional gamma-ray sources; i.e., Co-60, Cs-137, etc. For these TLD's a nominal value of 1 nC/mrem is used, and is independent of source energy for 100 keV to 3 MeV. Since measured dose equivalents at SLAC are only a small fraction of the allowable levels, it was not deemed necessary to develop neutron dosimeters which would measure dose equivalent accurately for all possible neutron spectra. Today, wallet TLD's, composed of pairs of Li-7 and Li-6 discs, are used, with the Li-6 measuring only thermal neutrons; i.e., they aren't moderated in any way to make them sensitive to neutrons with energies greater than thermal. The assumption is made that there is a correlation between thermal neutron fluences and fast neutron fluences around the research area where almost all neutron doses (exclusive of sealed sources) are received. The calibration factor for these Li-6 TLD's is 1 nC/mrem of fast neutrons. The method of determining the validity of this calibration is the subject of this note. 4 refs., 9 figs., 1 tab

Predictable self-assembled [2×2] Ln(III)4 square grids (Ln = Dy,Tb)-SMM behaviour in a new lanthanide cluster motif.

Science.gov (United States)

Anwar, Muhammad Usman; Thompson, Laurence Kenneth; Dawe, Louise Nicole; Habib, Fatemah; Murugesu, Muralee

2012-05-14

The ditopic carbohydrazone ligand (L1) produces the square, self-assembled [2×2] grids [Dy(4)(L1)(4)(OH)(4)]Cl(2) (1) and [Ln(4)(L1)(4)(μ(4)-O)(μ(2)-1,1-N(3))(4)] (Ln = Dy (2), Tb (3)), with 2 exhibiting SMM behaviour. Two relaxation processes occur with U(eff) = 51 K, 91 K in the absence of an external field, and one with U(eff) = 270 K in the presence of a 1600 Oe optimum field. This journal is © The Royal Society of Chemistry 2012

Personal neutron monitoring using TLD albedo combined with etched tracks detector

Energy Technology Data Exchange (ETDEWEB)

Tsujimura, N.; Momose, T. [Japan Nuclear Cycle Development Institute, Ibarakiken (Japan)

2002-07-01

The albedo dosimetry has been carried out in personal neutron monitoring in the MOX fuel plant of JNC Tokai Works, however, it has shortcomings mainly due to the inherently poor energy response. This paper describes our efforts to overcome these difficulties in practical use of albedo dosemeters. The following four subjects are presented: (1) the neutron energy response functions of albedo TLD obtained from the mono-energetic neutron irradiation experiments and the Monte-Carlo calculations, (2) the location- dependent correction factors calculated from the response functions and neutron energy spectra measured in the workplaces, (3) the results of the international personal neutron dosimetry intercomparison program, and (4) the operational comparison program of TLD albedo and etched tracks detector worn by workers engaged in the fabrication process of the MOX fuel plant. Finally, the characteristics of the combination neutron dosemeter using TLD albedo and solid state etched track detector are summarized.

Evaluation of the substitution of PMMA plates by PLA 3D printed in TL response of CaSO{sub 4}:Dy; Avaliacao da substituicao de placas de PMMA por PLA impresso 3D na resposta TL do CaSO{sub 4}:Dy

Energy Technology Data Exchange (ETDEWEB)

Almeida, Shirlane Barbosa de; Valeriano, Caio Cesar Santos; Campos, Leticia Lucente, E-mail: caio144fisicamedica@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2016-07-01

The CaSO{sub 4}:Dy is a dosimetric material that is nationally produced, which presents high sensibility but a high energy dependence of its thermoluminescent (TL) response at the photoelectric effect region. This study aims to compare the TL response of the CaSO{sub 4}:Dy when irradiated, with different energies, at the presence of 3D printed plates of polylactic acid (PLA) and polymethylmethacrylate (PMMA). Results show that the PLA has a different attenuation of the radiation, when compared to PMMA, indicating that it should be taken into account the quality of the print used on PLA plates manufacture. (author)

Synthesis and luminescence properties of Eu"2"+ doped CaSO_4 phosphor

International Nuclear Information System (INIS)

Aghalte, G.A.; Dhoble, S.J.; Pawar, N.R.

2016-01-01

Eu"2"+ doped CaSO_4 Phosphor were synthesized by precipitation method. PL analysis of Eu"2"+ activated CaSO_4 phosphor exhibited characteristic emission properties; CaSO_4:Eu Phosphor has received considerable attention because of its high sensitivity to X-ray and λ ray irradiation. CaSO_4:Eu phosphor powder was successfully synthesized by the wet chemical co-precipitation method. The structure morphology and luminescent properties of the phosphor were characterized by X-ray diffraction, scanning electron microscopy and photoluminescence spectroscopy

Effect of Si substitution on structural, electronic and optical properties of YNi{sub 4}Si-type DyNi{sub 5−x}Si{sub x} (x=0, 1, 2) compounds

Energy Technology Data Exchange (ETDEWEB)

Maurya, Dinesh Kumar; Saini, Sapan Mohan, E-mail: smsaini.phy@nitrr.ac.in

2016-10-15

We employed first principle calculations for investigation of structural, electronic and optical properties of YNi{sub 4}Si-type DyNi{sub 5−x}Si{sub x} (x=0, 1, 2) compounds. These properties are studied first time on YNi{sub 4}Si-type DyNi{sub 5−x}Si{sub x} compounds. The exchange and correlation potential is treated by the Coulomb corrected local spin density approximation (LSDA+U) method for better accounting of the correlation between the 4f electrons. The optimized lattice constants and internal cell parameters are in agreement with the available data. Self consistence band structure calculations show that Ni-3d states remains in valance band and dominant below the E{sub F}, while Dy-5d and 4f states mainly contributes above Fermi Energy (E{sub F}) in DyNi{sub 5−x}Si{sub x} (x=0, 1, 2) compounds. We also find that when silicon for nickel substitution takes place (DyNi{sub 4}Si), there is a gradual hybridization of Ni-3d and Si-3p states results, nickel moments decrease rapidly in agreement with the experiment. Optical spectra shows the main absorption peak around 4 eV depends on the substituent concentration and could be due to transition from hybridized band (Ni-3d and Si-3p), below E{sub F} to free Dy-4d states. Frequency-dependent refractive index, n(ω), and the extinction coefficient, k(ω), of DyNi{sub 5−x}Si{sub x} (x=0, 1, 2) are also calculated for the radiation up to 14 eV. - Highlights: • Calculated DOS revels that Ni-3d states are dominated below Fermi level (E{sub F}). • Spin down Dy-4f states show significant contribution to DOS above E{sub F.} • Nickel moments decrease rapidly with substitution of silicon for nickel (DyNi{sub 4}Si). • Most significant peak is found around 7eV in optical conductivity. • Nickel moments decrease rapidly with substitution of silicon for nickel (DyNi{sub 4}Si). • Peak indicates the possibility of transitions from Ni-3d states to empty spin down Dy-4f states.

On the photo-luminescence properties of sol–gel derived undoped and Dy3+ ion doped nanocrystalline Scheelite type AMoO4 (A = Ca, Sr and Ba)

International Nuclear Information System (INIS)

Jena, Paramananda; Gupta, Santosh K.; Natarajan, V.; Padmaraj, O.; Satyanarayana, N.; Venkateswarlu, M.

2015-01-01

Nanocrystalline Scheelite type Dy doped AMoO 4 [where A = Ba, Sr and Ca] samples were prepared by acrylamide assisted sol–gel process and characterized by XRD, FT-Raman, FTIR, SEM and photoluminescence (PL). PL of undoped sample shows blue/green emission in CaMoO 4 and SrMoO 4 but multicolour visible emission leading to near white light in BaMoO 4 nanoparticles; the origin of which is explained. It was observed that on doping 0.5 mol% of Dy 3+ in molybdate samples complete energy transfer takes place in case of SrMoO 4 and BaMoO 4 , but host contributed substantially in Dy doped BaMoO 4 sample, resulting in biexponential decay. It was also observed that symmetry around Dy 3+ decreases as the size of alkaline earth ion increases. Due to combined blue, yellow and red colour emission in dysprosium doped sample; all samples showed near white light emission under UV and near UV excitation

Phosphorescence behavior and photoluminescence mechanism of Dy{sup 3+} sensitized β-Zn{sub 3}(PO{sub 4}){sub 2}: Mn{sup 2+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Xie, Ting; Guo, Hongxu [School of Chemistry & Environment, Minnan Normal University, Zhangzhou 363000, Fujian (China); Zhang, Junying [Department of Physics, Beihang University, Beijing 100191 (China); Odetola, Christopher [Department of Chemistry, University of Ontario Institute of Technology, Ontario L1H 7K4 (Canada); He, Yuneng; Lin, Heng; Chen, Guoliang [School of Chemistry & Environment, Minnan Normal University, Zhangzhou 363000, Fujian (China); Zheng, Zishan, E-mail: Z.Zheng@mnnu.edu.cn [School of Chemistry & Environment, Minnan Normal University, Zhangzhou 363000, Fujian (China)

2015-09-05

Highlights: • A red long persistent phosphor of β-Zn{sub 3}(PO{sub 4}){sub 2}: Mn{sup 2+}, Dy{sup 3+} was synthesized. • Dy{sup 3+} as a sensitizer transfers its energy to the luminescent center of Mn{sup 2+}. • The three factors are responsible for the improvement of LPP properties. - Abstract: A red long persistent phosphor (LPP) of β-Zn{sub 3}(PO{sub 4}){sub 2}: Mn{sup 2+}, Dy{sup 3+} was synthesized conventionally via homogeneous coprecipitation and conventional solid-state sintering methods. The emission peak of phosphor was found at 620 nm, which can be assigned to the {sup 4}T{sub 1g} → {sup 6}A{sub 1g} transition of Mn{sup 2+}. The decay curves of phosphors show that Dy{sup 3+} ions co-doping can largely improve the performance of the red LLP of β-Zn{sub 3}(PO{sub 4}){sub 2}: Mn{sup 2+}. This red long-persistent luminescence was observed for about 4 h in the limit of light perception for naked eyes when excited under 254 nm UV light for 5 min. Thermoluminescence analysis indicates that the dopant of Dy{sup 3+} ions produced suitable trap depth of defects that enhanced the luminescence of LPP. It is hypothesized that Dy{sup 3+} as a sensitizer transfers its energy to the luminescent center of Mn{sup 2+}. We propose that the emission mechanism of LPP experiences a series process of electron–hole pairs: production, release, movement and combination. The decay time of LPP has close relationship with the life span of electron–hole pairs during their releasing time from traps and moving length on their path.

Coercivity enhancement in hot deformed Nd2Fe14B-type magnets by doping low-melting RCu alloys (R = Nd, Dy, Nd + Dy)

Science.gov (United States)

Lee, Y. I.; Huang, G. Y.; Shih, C. W.; Chang, W. C.; Chang, H. W.; You, J. S.

2017-10-01

Magnetic properties of the anisotropic NdFeB magnets prepared by hot pressing followed by die-upsetting NdFeB MQU-F powders doped with low-melting RCu alloy powders were explored, where RCu stands for Nd70Cu30, Dy70Cu30 and (Nd0.5Dy0.5)70Cu30, respectively. In addition, the post-annealing at 600 °C was employed to modify the microstructures and the magnetic properties of the hot deformed magnets. It is found that doping RCu alloy powders is effective in enhancing the coercivity of the hot deformed NdFeB magnets from 15.1 kOe to 16.3-19.5 kOe. For Nd70Cu30-doped magnets, the increment of coercivity is only 1.2 kOe. Meanwhile, Dy70Cu30-doped and (Nd0.5Dy0.5)70Cu30-doped magnets show an almost identical enhancement of coercivity of about 4.4 kOe. Importantly, the latter magnet shows a beneficial effect of reducing the usage of Dy from 1.6 wt% to 0.8 wt%. TEM analysis shows that nonmagnetic Nd, Dy and Cu appear at grain boundary and isolate the magnetic grains, leading to an enhancement of coercivity. Doping lower melting point Dy-lean (Nd0.5Dy0.5)70Cu30 powders into commercial MQU-F powders for making high coercivity hot deformed NdFeB magnets might be a potential and economic way for mass production.

Effect of Ce{sup 3+} ion on Dy{sup 3+} or Mn{sup 2+} in KMgSO{sub 4}Cl synthesized by centrifuge method

Energy Technology Data Exchange (ETDEWEB)

Shinde, Nita [Department of Physics R.T.M. Nagpur University, Nagpur 440033 (India); Dhoble, N.S. [Department of Chemistry, Sevadal Mahila Mahavidyalaya, Nagpur 440018 (India); Gedam, S.C., E-mail: gedam_sc@rediffmail.com [K.Z.S. Science College, Kalmeshwar, Nagpur 441501 (India); Dhoble, S.J. [Department of Physics R.T.M. Nagpur University, Nagpur 440033 (India)

2016-04-15

In this paper effect of Ce{sup 3+} ion on Dy{sup 3+} and Mn{sup 2+} ions in microcrystalline KMgSO{sub 4}Cl host prepared by ethanol (centrifuge technique) method has been discussed. In KMgSO{sub 4}Cl sample X-ray diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence (PL) characteristics have been studied. Powder X-ray diffraction analysis shows the crystalline nature of the phosphor prepared by this new route. The morphological structures of the samples were conducted using SEM technique. An average crystallite size was found to be 5 μm. Photoluminescence in KMgSO{sub 4}Cl:Ce{sup 3+} is observed at 324 nm and 344 nm along with red emission broad band at around 644 nm. In KMgSO{sub 4}Cl: Ce, Dy phosphor Ce{sup 3+} emission around 324 and 344 nm overlaps rather well with Dy{sup 3+} excitation. The addition of Ce{sup 3+} showed higher photoluminescence (PL) intensity for the Dy{sup 3+} emissions around 482 and 576 nm excited via Ce{sup 3+} ions at 284 nm due to {sup 4}F{sub 9/2} to {sup 6}H{sub 15/2} and {sup 6}H{sub 13/2} levels. Ce{sup 3+}→Mn{sup 2+} energy transfer process occurs in KMgSO{sub 4}Cl host. KMgSO{sub 4}Cl: Mn does not give PL at 284 nm excitation but for co-doped samples with cerium, Mn{sup 2+} ions exhibits efficient fluorescence at around 560 nm due to {sup 4}T{sub 1}–{sup 6}A{sub 1} transition. KMgSO{sub 4}Cl: Dy or KMgSO{sub 4}Cl: Mn directly exciting does not show any emission while addition of Mn{sup 2+}, enhances red emission of Ce{sup 3+} at 644 nm. The CIE co-ordinates of KMgSO{sub 4}Cl:Ce; KMgSO{sub 4}Cl:Ce, Dy and KMgSO{sub 4}Cl:Ce, Mn phosphors reveals that the emission colour varies from blue to deep-red. Hence this material may be a potential lamp phosphor. - Highlights: • KMgSO{sub 4}Cl: Ce3{sup +} along with Dy3{sup +} and Mn2{sup +} was prepared by centrifuge method. • Particle size was found to be 5 μm using SEM technique. • The emission varies from blue to deep-red.

Tunable luminescence and energy transfer properties of KSr{sub 4}(BO{sub 3}){sub 3}:Dy{sup 3+}, Eu{sup 3+} phosphors for near-UV warm-white LEDs

Energy Technology Data Exchange (ETDEWEB)

Leng, Zhihua; Li, Linlin; Liu, Yali; Zhang, Nannan; Gan, Shucai, E-mail: gansc@jlu.edu.cn

2016-05-15

Dy{sup 3+} and Eu{sup 3+} codoped KSr{sub 4}(BO{sub 3}){sub 3} phosphors were successfully synthesized by solid-state reaction process. Under near-ultraviolet (near-UV) excitation, individual Dy{sup 3+} or Eu{sup 3+} ion activated sample exhibits characteristic emissions in their respective regions. In KSr{sub 4}(BO{sub 3}){sub 3}:Dy{sup 3+}, xEu{sup 3+} phosphors, the energy transfer from Dy{sup 3+} to Eu{sup 3+} was revealed to be resonant type by dipole–dipole mechanism. And the critical distance R{sub Dy–Eu} was calculated to be 13.95 Å. The energy transfer efficiency of KSr{sub 4}(BO{sub 3}){sub 3}:Dy{sup 3+}, xEu{sup 3+} reached about 20% when the concentration of Eu{sup 3+} was 0.035. Moreover, the emitting colors of Dy{sup 3+} and Eu{sup 3+} codoped samples can be adjusted from the edge of white area to warm white via tuning the activator (Eu{sup 3+}) doped concentration. More significantly, the chromaticity coordinates (0.334, 0.351) of KSr{sub 4}(BO{sub 3}){sub 3}:0.005Dy{sup 3+}, 0.015Eu{sup 3+} sample are extremely adjacent to standard white light (0.33, 0.33). The quantum efficiency of the KSr{sub 4}(BO{sub 3}){sub 3}:0.005Dy{sup 3+}, 0.015Eu{sup 3+} phosphor with 389 nm excitation is found to be 42%, demonstrating that the obtained single-component white-emitting phosphor exhibits potential applications for solid state lighting.

Environmental effects on TLD 100

International Nuclear Information System (INIS)

Lilley, E.; Howard, R.

1976-01-01

Reference is made to a recent paper by Dhar et al (Health Phys.; 25:427 (1973)) in which significant differences in the sensitivity of TLD 100 crystals following the same heat treatments in different environments, were reported. Similar work is here reported on TLD 100 at 400 0 C with half the crystals being heat treated in vacuum, irradiated and readout an then annealed in air, irradiated and readout while the other half of the crystals were air annealed and readout before vacuum annealing and readout. In both cases no significant change was detected in contrast to the results of Dhar et al. (U.K.)

TLD audit in the radiotherapy at the national level

International Nuclear Information System (INIS)

Kroutilikova, D.; Zackova, H.; Novotny, J.; Pridal, I.

1998-01-01

Czech legislation requires that all radiotherapy departments undertake quality independent audit annually. An authorized auditing group was created as a body of the National Radiation Protection Institute. It has been decided that TLD postal audit combined with film dosimetry would alternate with in situ audit every two or three years. For this, a local TLD measuring network has been established. The methods applied in the TLD audit were taken from EROPAQ and EURAQA projects in 1996 and modified to comply with Czech local circumstances. First TLD audits were started in February 1997. During the February to September period, 60 beams were checked: 26 Co-60 beams, 10 Cs-137 beams, 15 X-ray beams, and 9 electron beams. Details of the measurements and their results are given. (P.A.)

Response studies of three different dosimeters for skin entrance dose measurements using diagnostic X-ray machines

International Nuclear Information System (INIS)

Sonawane, A.U.; Kulkarni, Arti; Shirva, V.K.; Butani, M.L.; Pradhan, A.S.

2008-01-01

A TLD method based on CaSO 4 :Dy Teflon discs developed at the Bhabha Atomic Research Centre, Mumbai has been extensively used for various applications in diagnostic radiology in India. This method was recently used for evaluation of radiation quality and measurement of skin entrance doses (SEDs) in various hospitals for different diagnostic examinations. The use of TLD discs for these applications involves the process of preparation of TLD discs with different combination of filters and then measurement of TL output under different combinations of filters. The measurement of SEDs in diagnostic radiology is also carried out instantaneously and accurately by using very user friendly and compact state-of-art instruments. These consist of kVp Test-O-Meter (ToM) (Model RADIFLU-9001) and the dose ToM (Model 6001) manufactured by M/s UNFORS, Sweden. The kVp meter automatically calculates kVp and updates it every second in the range from 55 to 145 kVp with the resolution of 0.1 kV. The dose ToM incorporates sealed silicon detector having lead shield under and around, which prevents backscattered radiation from influencing the measurement. The dose Test-O-Meter has excellent energy independence in the range from 50 to 150 kVp and inaccuracy not exceeding 5 % at 70 k Vp. The dose meter is capable of measuring doses up to 9999 μGy

Neutron detection using Dy2O3 activation detectors

International Nuclear Information System (INIS)

Gomaa, M.A.; Mohamed, E.J.

1979-01-01

The aim of the present study is to examine the usefulness of Dy 2 O 3 not only as thermal neutron activation detector but also as a fast neutron detector. For thermal neutrons, the half life of 165 Dy is measured to be (141 +- 6) min, its response to thermal neutrons is (2.18 +- 0.01) cpm/ncm -2 s -1 for a 250 mg Dy 2 O 3 pellet. For fast neutrons the Dy 2 O 3 detector is placed within a 20 cm polyethylene sphere and its response is found to be (2.2 +- 0.1) cpm/ncm -2 s -1 for 4 MeV neutrons and (2.10 +- 0.04) cpm/ncm -2 s -1 for 14 MeV neutrons. For neutron dosimetry, its response is found to be (16.7 +- 0.4) cpm per mrem h -1 . (author)

A primary assessment of a daybreak 2200 OSL reader using fine grain quartz and CaSO4:Tm TLD

International Nuclear Information System (INIS)

Zhang Keqi; Chen Jie; Lu Yanchou; Wang Changsheng; Yang Chuancheng

2007-01-01

Daybreak 2200 OSL readers are widely used for luminescence dating applications. As the sample irradiation and illumination may affect discs in adjacent positions, it is critical to confirm that these factors do not introduce significant systematic errors. Effects of cross-irradiation and cross-bleaching were examined and quantified using fine-grain quartz and highly sensitive CaSO 4 :Tm dosimeters, and the irradiation offset time was measured. The cross-bleaching effect on adjacent aliquots is non-linear with no more than 15% OSL signal reduction following 10ks illumination with the power of blue LED being at 95% maximum. But at positions other than the nearest neighboring sample, almost no effect of cross-bleaching was found. The cross-talk dose, even to the nearest samples, was about 0.02% of the applied dose, and it decreased with increasing distance from the source. Offset time of the built-in Beta source shutter is 0.22 s, which can be neglected in regular dating, and leak dose of the source can be ignored as well. Finally, measurement consistency at Position 0.5, 10, ..... and 55 of the sample tray is better than 3% in relative standard deviation. (authors)

Australian participation in international intercomparisons of environmental dosemeters

International Nuclear Information System (INIS)

Boas, J.F.; David, R.C.; Jones, J.

2002-01-01

The Environmental Measurements Laboratory of the U.S. Department of Energy has conducted international intercomparisons of environmental dosemeters at regular intervals since 1974. This paper reports the results obtained in the 10th and 11th intercomparisons by JFB and JGY at the Australian Radiation Laboratory (in 1992 and 1996 respectively) and in the 12th intercomparison by JFB and DRCT at the Australian Radiation Protection and Nuclear Safety Agency and by JGY and JJ at Australian Radiation Serviceces during 2000 and 2001. The ARL/ARPANSA measurements used a simple dosemeter holder containing two CaSO 4 :Dy impregnated Teflon discs, one unshielded and the other shielded by approximately 2.4 mm of Cu. The ARS measurements used a commercially available TLD badge case containing a CaSO 4 :Dy impregnated Teflon card. The commercial badge case was not symmetrical in design. The filtration in the front and rear sections of the commercial badge case varied from an open area to an area shielded by copper, tin and cadmium. The results obtained were generally within ±15% of the reference values measured by EML using high-pressure ionisation chambers for dosemeters exposed hi the field to environmental radiation and for dosemeters given a single exposure to 137 Cs or 241 Am at EML or an associated laboratory. Similar agreement was obtained for dosemeters exposed in the field and also given a single exposure to 137 Cs radiation. In order to obtain this measure of agreement, the dosemeters were individually calibrated and the readouts corrected for fading. Copyright (2002) Australasian Radiation Protection Society Inc

Cytotoxic and genotoxic effect of the [166Dy]Dy/166Ho-EDTMP in vivo generator system in mice

International Nuclear Information System (INIS)

Pedraza-Lopez, Martha; Ferro-Flores, Guillermina; Arteaga de Murphy, Consuelo; Morales-Ramirez, Pedro; Piedras-Ross, Josefa; Murphy-Stack, Eduardo; Hernandez-Oviedo, Omar

2004-01-01

Multiple myeloma and other hematological malignancies have been treated by myeloablative radiotherapy/chemotherapy and subsequent stem cell transplantation. [ 166 Dy]Dy/ 166 Ho-ethylenediaminetetramethylene phosphonate (EDTMP) forms a stable in vivo generator system with selective skeletal uptake in mice; therefore, it could work as a potential and improved agent for marrow ablation. Induced bone marrow cytotoxicity and genotoxicity are determined by the reduction of reticulocytes (RET) and elevation of micronucleated reticulocyte (MN-RET) in peripheral blood and ablation by bone marrow histological studies. The aim of this study was to determine the bone marrow cytotoxic and genotoxic effect of the [ 166 Dy]Dy/ 166 Ho-EDTMP in vivo generator system in mice and to evaluate by histopathology its myeloablative potential. Enriched 166 Dy 2 O 3 was irradiated and [ 166 Dy]DyCl 3 was added to EDTMP in phosphate buffer (pH 8.0) in a molar ratio of 1:1.75. QC was determined by TLC. Dy-EDTMP complex was prepared the same way with nonirradiated dysprosium oxide. A group of BALB/c mice were intraperitoneally injected with the radiopharmaceutical and two groups of control animals were injected with the cold complex and with 0.9% sodium chloride, respectively. A blood sample was taken at the beginning of the experiments and every 48 h for 12 days postinjection. The animals were sacrificed, organs of interest taken out and the radioactivity determined. The femur was used for histological studies. Flow cytometry analysis was used to quantify the frequency of RET and MN-RET in the blood samples. The MCNP4B Monte Carlo computer code was used for dosimetry calculations. Radiochemical purity was 99% and the mean specific activity was 1.3 MBq/mg. The RET and MN-RET frequency were statistically different in the treatment at the end of the 12-day period demonstrating cytotoxicity and genotoxicity induced by the in vivo generator system. The histology studies show that there was

Thermoluminescent dosimeters (TLD) quality assurance network in the Czech Republic.

Science.gov (United States)

Kroutilķková, Daniela; Novotný, Josef; Judas, Libor

2003-02-01

The Czech thermoluminescent dosimeters (TLD) quality assurance network was established in 1997. Its aim is to pursue a regular independent quality audit in Czech radiotherapy centres and to support state supervision. The audit is realised via mailed TL dosimetry. The TLD system consists of encapsulated LiF:Mg,Ti powder (type MT-N) read with Harshaw manual reader model 4000. Basic mode of the TLD audit covers measurements under reference conditions, specifically beam calibration checks for all clinically used photon and electron beams. Advanced mode consists of measurements under both reference and non-reference conditions using a solid multipurpose phantom ('Leuven phantom') for photon beams. The radiotherapy centres are instructed to deliver to the TLD on central beam axis absorbed dose of 2 Gy calculated with their treatment planning system for a particular treatment set-up. The TLD measured doses are compared with the calculated ones. Deviations of +/-3% are considered acceptable for both basic and advanced mode of the audit. There are 34 radiotherapy centres in the Czech Republic. They undergo the basic mode of the TLD audit regularly every 2 years. If a centre shows a deviation outside the acceptance level, it is audited more often. Presently, most of the checked beams comply with the acceptance level. The advanced TLD audit has been implemented as a pilot study for the present. The results were mostly within the acceptance limit for the measurements on-axis, whereas for off-axis points they fell beyond the limit more frequently, especially for set-ups with inhomogeneities, oblique incidence and wedges. The results prove the importance of the national TLD quality assurance network. It has contributed to the improvement of clinical dosimetry in the Czech Republic. In addition, it helps the regulatory authority to monitor effectively and regularly radiotherapy centres.

Thermoluminescent dosimeters (TLD) quality assurance network in the Czech Republic

International Nuclear Information System (INIS)

Kroutilikova, Daniela; Novotny, Josef; Judas, Libor

2003-01-01

Introduction: The Czech thermoluminescent dosimeters (TLD) quality assurance network was established in 1997. Its aim is to pursue a regular independent quality audit in Czech radiotherapy centres and to support state supervision. Materials and methods: The audit is realised via mailed TL dosimetry. The TLD system consists of encapsulated LiF:Mg,Ti powder (type MT-N) read with Harshaw manual reader model 4000. Basic mode of the TLD audit covers measurements under reference conditions, specifically beam calibration checks for all clinically used photon and electron beams. Advanced mode consists of measurements under both reference and non-reference conditions using a solid multipurpose phantom ('Leuven phantom') for photon beams. The radiotherapy centres are instructed to deliver to the TLD on central beam axis absorbed dose of 2 Gy calculated with their treatment planning system for a particular treatment set-up. The TLD measured doses are compared with the calculated ones. Deviations of ±3% are considered acceptable for both basic and advanced mode of the audit. Results: There are 34 radiotherapy centres in the Czech Republic. They undergo the basic mode of the TLD audit regularly every 2 years. If a centre shows a deviation outside the acceptance level, it is audited more often. Presently, most of the checked beams comply with the acceptance level. The advanced TLD audit has been implemented as a pilot study for the present. The results were mostly within the acceptance limit for the measurements on-axis, whereas for off-axis points they fell beyond the limit more frequently, especially for set-ups with inhomogeneities, oblique incidence and wedges. Conclusions: The results prove the importance of the national TLD quality assurance network. It has contributed to the improvement of clinical dosimetry in the Czech Republic. In addition, it helps the regulatory authority to monitor effectively and regularly radiotherapy centres

Dosimetric behavior of thermoluminescent dosimeters at low doses in diagnostic radiology; Comportamiento dosimetrico de dosimetros termoluminiscentes a bajas dosis en radiodiagnostico

Energy Technology Data Exchange (ETDEWEB)

Del Sol F, S.; Garcia S, R.; Guzman M, J.; Sanchez G, D.; Rivera M, T. [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Av. Legaria 694, Col. Irrigacion, 11500 Mexico D. F. (Mexico); Ramirez R, G. [Hospital Juarez de Mexico, Av. IPN 5160, Col. Magdalena de las Salinas, 07760 Mexico D. F. (Mexico); Gaona, E., E-mail: susi2489@hotmail.com [Universidad Autonoma Metropolitana, Unidad Xochimilco, Calz. del Hueso 1100, Col. Villa Quietud, 04960 Mexico D. F. (Mexico)

2015-10-15

Thermoluminescent (Tl) characteristics of TLD-100, LiF:Mg,Cu,P, and CaSO{sub 4}: Dy the under homogeneous field of X-ray beams of diagnostic irradiation and its verification using thermoluminescent dosimetry is presented. The irradiations were performed utilizing an X-ray beam generated by a Radiology Mexican Company: MRH-II E GMX 325-AF SBV-1 model, with Rotating Anode X-Ray Tube installed in the Hospital Juarez Norte de Mexico in Mexico City. Different thermoluminescent characteristics of dosimetric material were studied, such as, batch homogeneity, Tl glow curve, Tl response as a function of X-ray dose, reproducibility and fading. Materials were calibrated in terms of absorbed dose to the standard calibration distance and positioned in a generic Phantom was used. Dose verification and comparison with the measurements made with that obtained by TLD-100 were analyzed. Preliminary results indicate the dosimetric peak appears at 243, 236 and 277 ± 5 degrees C respectively, these peaks are in agreement with that reported in the literature. Tl glow curve as a function of X-ray dose showed a linearity in the range from 1.76 mGy up to 14.70 mGy for all materials. Fading for a period of one month at room temperature showed low fading LiF:Mg,Cu,P, medium and high for TLD-100 and CaSO{sub 4}: Dy. The results suggest that the three materials are suitable for measurements at low doses in radiodiagnostic, however, for its dosimetric characteristics are most effective for individual applications: personal dosimetry and monitors limb (LiF:Mg,Cu,P), clinical dosimetry and environmental (TLD-100 and CaSO{sub 4}: Dy). (Author)

Study of a method based on TLD detectors for in-phantom dosimetry in BNCT

Energy Technology Data Exchange (ETDEWEB)

Gambarini, G. [Dept. of Physics of the Univ., Via Celoria 16, 20133 Milan (Italy); INFN, Natl. Inst. of Nuclear Physics, Via Celoria 16, 20133 Milan (Italy); Klamert, V. [Dept. of Nuclear Eng. of Polytechnic, CESNEF, Via Ponzio 34/3, 20133 Milan (Italy); Agosteo, S. [INFN, Natl. Inst. of Nuclear Physics, Via Celoria 16, 20133 Milan (Italy); Dept. of Nuclear Eng. of Polytechnic, CESNEF, Via Ponzio 34/3, 20133 Milan (Italy); Birattari, C.; Gay, S. [Dept. of Physics of the Univ., Via Celoria 16, 20133 Milan (Italy); INFN, Natl. Inst. of Nuclear Physics, Via Celoria 16, 20133 Milan (Italy); Rosi, G. [FIS-ION, ENEA, Casaccia, Via Anguillarese 301, 00060 Santa Maria di Galeria, Rome (Italy); Scolari, L. [Dept. of Physics of the Univ., Via Celoria 16, 20133 Milan (Italy); INFN, Natl. Inst. of Nuclear Physics, Via Celoria 16, 20133 Milan (Italy)

2004-07-01

A method has been developed, based on thermoluminescent dosemeters (TLD), aimed at measuring the absorbed dose in tissue-equivalent phantoms exposed to thermal or epithermal neutrons, separating the contributions of various secondary radiation generated by neutrons. The proposed method takes advantage of the very low sensitivity of CaF{sub 2}:Tm (TLD-300) to low energy neutrons and to the different responses to thermal neutrons of LiF:Mg,Ti dosemeters with different {sup 6}Li percentage (TLD-100, TLD-700, TLD-600). The comparison of the results with those obtained by means of gel dosemeters and activation foils has confirmed the reliability of the method. The experimental modalities allowing reliable results have been studied. The glow curves of TLD-300 after gamma or neutron irradiation have been compared; moreover, both internal irradiation effect and energy dependence have been investigated. For TLD-600, TLD-100 and TLD-700, the suitable fluence limits have been determined in order to avoid radiation damage and loss of linearity. (authors)

Study of physical factors affecting the TLD readout

International Nuclear Information System (INIS)

Ahmed, Amira Abd Elrhman Ebrahim

2015-10-01

The aim of the study was to study the effects of physical factors in TLD reading. The dosimeters have been irradiated with x rays of (0.5 mGy to 5 mGy) using plastic holder with Aluminum filters with dimensions 1.5 x 0.8 mm and 0.5 mm in thickness to obtain the equivalent dose Hp (10) flux of nitrogen gas and annealing after data collection by TLD Reader Analyzer 04 (Version 0.9.400 micro lab (krakow 2012). The count and dose analysis shows that; The count/s given by TLD appears to be higher in case of using filtration which was 7189.9 eps in contrast with reading without filter which was 4055.8 eps. There was proportional linear relationship between the applied dose and the TLD count for both cases with and without filter. And the correlation could be fitted in the form of equations: y=423.9 x + 1023 and y = 432.5 x + 405.3 for filtered and y refers to count/s. Such increment in count is ascribed to increasing applied radiation dose as well it indicates and confirms the linearity of TLD in measuring the radiation dose since R 2 = 0.9. However the count with filter for the applied radiation dose in mGy was greater than that without filter. The that measured with pellets annealing (reading of zero doses). TLD pellets reading without zero dose measurement usually gives greater dose ( 441.8 and 563.6 μGy) relative to the case where the zero doses have been measured which were 289.6 and 429.2 μGy, respectively. While the effect of using filtration is so obvious and leads to increase of zero dose, respectively relative to dose s of un reading of zero dose, and reading of zero dose, but without filter.(Author)

Analysis of uncertainties in the IAEA/WHO TLD postal dose audit system

Energy Technology Data Exchange (ETDEWEB)

Izewska, J. [Department of Nuclear Sciences and Applications, International Atomic Energy Agency, Wagramer Strasse 5, Vienna (Austria)], E-mail: j.izewska@iaea.org; Hultqvist, M. [Department of Medical Radiation Physics, Karolinska Institute, Stockholm University, Stockholm (Sweden); Bera, P. [Department of Nuclear Sciences and Applications, International Atomic Energy Agency, Wagramer Strasse 5, Vienna (Austria)

2008-02-15

The International Atomic Energy Agency (IAEA) and the World Health Organisation (WHO) operate the IAEA/WHO TLD postal dose audit programme. Thermoluminescence dosimeters (TLDs) are used as transfer devices in this programme. In the present work the uncertainties in the dose determination from TLD measurements have been evaluated. The analysis of uncertainties comprises uncertainties in the calibration coefficient of the TLD system and uncertainties in factors correcting for dose response non-linearity, fading of TL signal, energy response and influence of TLD holder. The individual uncertainties have been combined to estimate the total uncertainty in the dose evaluated from TLD measurements. The combined relative standard uncertainty in the dose determined from TLD measurements has been estimated to be 1.2% for irradiations with Co-60 {gamma}-rays and 1.6% for irradiations with high-energy X-rays. Results from irradiations by the Bureau international des poids et mesures (BIPM), Primary Standard Dosimetry Laboratories (PSDLs) and Secondary Standards Dosimetry Laboratories (SSDLs) compare favourably with the estimated uncertainties, whereas TLD results of radiotherapy centres show higher standard deviations than those derived theoretically.

Automated TLD system for gamma radiation monitoring

International Nuclear Information System (INIS)

Nyberg, P.C.; Ott, J.D.; Edmonds, C.M.; Hopper, J.L.

1979-01-01

A gamma radiation monitoring system utilizing a commercially available TLD reader and unique microcomputer control has been built to assess the external radiation exposure to the resident population near a nuclear weapons testing facility. Maximum use of the microcomputer was made to increase the efficiency of data acquisition, transmission, and preparation, and to reduce operational costs. The system was tested for conformance with an applicable national standard for TLD's used in environmental measurements

Family of defect-dicubane Ni4Ln2 (Ln = Gd, Tb, Dy, Ho) and Ni4Y2 complexes: rare Tb(III) and Ho(III) examples showing SMM behavior.

Science.gov (United States)

Zhao, Lang; Wu, Jianfeng; Ke, Hongshan; Tang, Jinkui

2014-04-07

Reactions of Ln(III) perchlorate (Ln = Gd, Tb, Dy, and Ho), NiCl2·6H2O, and a polydentate Schiff base resulted in the assembly of novel isostructural hexanuclear Ni4Ln2 complexes [Ln = Gd (1), Tb (2), Dy (3), Ho (4)] with an unprecedented 3d-4f metal topology consisting of two defect-dicubane units. The corresponding Ni4Y2 (5) complex containing diamagnetic Y(III) atoms was also isolated to assist the magnetic studies. Interestingly, complexes 2 and 3 exhibit SMM characteristics and 4 shows slow relaxation of the magnetization. The absence of frequency-dependent in-phase and out-of-phase signals for the Ni-Y species suggests that the Ln ions' contribution to the slow relaxation must be effectual as previously observed in other Ni-Dy samples. However, the observation of χ″ signals with zero dc field for the Ni-Tb and Ni-Ho derivatives is notable. Indeed, this is the first time that such a behavior is observed in the Ni-Tb and Ni-Ho complexes.

Effect of separated layer thickness on magnetoresistance and magnetic properties of Co/Dy/Co and Ni/Dy/Ni film systems

Science.gov (United States)

Shabelnyk, T. M.; Shutylieva, O. V.; Vorobiov, S. I.; Pazukha, I. M.; Chornous, A. M.

2018-01-01

Co(5 nm)/Dy(tDy)/Co(20 nm)/S and Ni(5 nm)/Dy(tDy)/Ni(20 nm)/S trilayer films are prepared by electron-beam sputtering to investigate the influence of dysprosium layer thickness (tDy) and thermal annealing on the crystal structure, magnetoresistance (MR) and magnetic properties of thin films. The thickness of Dy layer changed in the range from 1 nm to 20 nm. The samples annealed for 20 min at 700 K. Electron diffraction patterns reveal that the as-deposited and annealed systems Co/Dy/Co and Ni/Dy/Ni had fcc-Co + hcp-Dy and fcc-Ni + hcp-Dy phase state, respectively. It is also shown that at the tDy = 15 nm the transition from amorphous to crystalline structures of Dy layer is observed. An increase in the Dy layer thickness results in changes in the MR and magnetic properties of the trilayer systems. It is shown that MR is most thermally stable against annealing to 700 K at tDy = 15 nm for Co/Dy/Co as well as for Ni/Dy/Ni. For tDy = 15 nm the, value of MR for both system increases by two times compared to those of pure ferromagnetic (FM) samples. The coercivity (Bc), remanent (Mr) and saturation (Ms) magnetization of the in-plain magnetization hysteresis loops are related to the Dy layer thickness too. The coercivity depends on the FM materials type and diffusion processes at the layer boundary. Accordingly, Mr and Ms are reduced with tDy increasing before and after annealing for both trilayer systems.

Search for superdeformed bands in {sup 154}Dy

Energy Technology Data Exchange (ETDEWEB)

Nisius, D.; Janssens, R.V.F.; Khoo, T.L. [and others

1995-08-01

The island of superdeformation in the vicinity of the doubly magic {sup 152}Dy yrast superdeformed (SD) band is thought to be well understood in the framework of cranked mean field calculations. In particular, the calculations suggested that in {sup 154}Dy there should be no yrast or near yrast SD minimum in the 40-60 h spin range, where SD bands in this mass region are thought to be {sup 153}Dy nucleus, it is populated. However, with the presence of five SD bands in the neighboring necessary to ascertain if the addition of one single neutron diminishes the importance of shell effects to the extent that superdeformation can no longer be sustained. In an experiment utilizing the increased resolving power of the early implementation phase of Gammasphere, the reaction {sup 122}Sn({sup 36}S,4n) at 165 MeV was employed to populate high spin states in {sup 154}Dy. In a four-day run with 36 detectors, over one billion triple and higher fold coincidence events were recorded. One new SD band was identified and was assigned to {sup 154}Dy. From comparisons with the Im{sup (2)} moments of inertia of the SD bands in {sup 152}Dy and {sup 153}Dy, a configuration based on (514)9/2{sup 2} neutrons coupled to the {sup 152}Dy SD core was proposed. One unexpected and as yet unexplained feature of this new SD band is that the transition energies are almost identical to those of an excited SD band in {sup 153}Dy. It is also worth noting that the feeding of the yrast states is similar to that achieved by the deexcitation from the ensemble of all entry states in the reaction. This observation emphasizes the statistical nature of the decay-out process. A paper reporting these results was accepted for publication.

Skin dose measurements using MOSFET and TLD for head and neck patients treated with tomotherapy

International Nuclear Information System (INIS)

Kinhikar, Rajesh A.; Murthy, Vedang; Goel, Vineeta; Tambe, Chandrashekar M.; Dhote, Dipak S.; Deshpande, Deepak D.

2009-01-01

The purpose of this work was to estimate skin dose for the patients treated with tomotherapy using metal oxide semiconductor field-effect transistors (MOSFETs) and thermoluminescent dosimeters (TLDs). In vivo measurements were performed for two head and neck patients treated with tomotherapy and compared to TLD measurements. The measurements were subsequently carried out for five days to estimate the inter-fraction deviations in MOSFET measurements. The variation between skin dose measured with MOSFET and TLD for first patient was 2.2%. Similarly, the variation of 2.3% was observed between skin dose measured with MOSFET and TLD for second patient. The tomotherapy treatment planning system overestimated the skin dose as much as by 10-12% when compared to both MOSFET and TLD. However, the MOSFET measured patient skin doses also had good reproducibility, with inter-fraction deviations ranging from 1% to 1.4%. MOSFETs may be used as a viable dosimeter for measuring skin dose in areas where the treatment planning system may not be accurate.

Skin dose measurements using MOSFET and TLD for head and neck patients treated with tomotherapy.

Science.gov (United States)

Kinhikar, Rajesh A; Murthy, Vedang; Goel, Vineeta; Tambe, Chandrashekar M; Dhote, Dipak S; Deshpande, Deepak D

2009-09-01

The purpose of this work was to estimate skin dose for the patients treated with tomotherapy using metal oxide semiconductor field-effect transistors (MOSFETs) and thermoluminescent dosimeters (TLDs). In vivo measurements were performed for two head and neck patients treated with tomotherapy and compared to TLD measurements. The measurements were subsequently carried out for five days to estimate the inter-fraction deviations in MOSFET measurements. The variation between skin dose measured with MOSFET and TLD for first patient was 2.2%. Similarly, the variation of 2.3% was observed between skin dose measured with MOSFET and TLD for second patient. The tomotherapy treatment planning system overestimated the skin dose as much as by 10-12% when compared to both MOSFET and TLD. However, the MOSFET measured patient skin doses also had good reproducibility, with inter-fraction deviations ranging from 1% to 1.4%. MOSFETs may be used as a viable dosimeter for measuring skin dose in areas where the treatment planning system may not be accurate.

Ortho-vanadates K3RE(VO4)2 (RE = La, Pr, Eu, Gd, Dy, Y) for near UV-converted phosphors

International Nuclear Information System (INIS)

Qin, Lin; Wei, Dong-Lei; Huang, Yanlin; Qin, Chuanxiang; Cai, Peiqing; Kim, Sun-Il; Seo, Hyo-Jin

2014-01-01

The orthovanadate poly-crystals K 3 RE(VO 4 ) 2 (RE = La, Pr, Eu, Gd, Dy, Y) were synthesized via the solid-state reaction route. The crystal phase formation was verified through X-ray diffraction (XRD) studies and was performed by structural refinements. The optical properties were also investigated in detail. K 3 RE(VO 4 ) 2 (RE = Eu, Dy, Gd, Pr, La, Y) phosphors present different luminescence behaviors: the profiles of excitation and emission spectra, the spectra shift, the luminescence decay lifetimes, the absolute quantum efficiency (QE), and the CIE color coordinates are very different. The luminescence of K 3 RE(VO 4 ) 2 (RE = La, Gd, Y, Pr) presents yellow or yellowish green color, while, K 3 Dy(VO 4 ) 2 and K 3 Eu(VO 4 ) 2 show white and red luminescence, respectively. This was discussed on the base of the different micro-structure, activator centers, and the charge transfer transitions from [VO 4 ] 3− groups in the lattices. K 3 Y(VO 4 ) 2 and K 3 Eu(VO 4 ) 2 show higher QE values of 47.0% and 45.0% at room temperature, respectively. All the phosphors have efficient absorption in the region of near-UV wavelengths or blue wavelength region. This can well match with the light from UV-LED (360–400 nm) or blue LED chips (450–480 nm) based on GaN semiconductor. K 3 RE(VO 4 ) 2 could be suggested to be a potential candidate to give further investigations for the application on near-UV excited white LEDs. - Graphical abstract: A series of orthovanadates K 3 RE(VO 4 ) 2 (RE = Eu, Dy, Gd, Pr, La, Y) have been developed to be new phosphors with rich luminescence colors; there are efficiency excitation in the near UV wavelength region. Compared with the reported vanadate phosphors K 3 R(VO 4 ) 2 has rich luminescence color, rich color, no concentration quenching, and comparable luminescence QE. - Highlights: • A new phosphor of non-doped of K 3 R(VO 4 ) 2 (R = Eu, Dy, Gd, Pr, La, Y) were developed by solid-state reaction route. • The phosphor

Thermoluminescence of SrAl_2O_4:Eu"2"+, Dy"3"+: dosimetric characteristics and evidence of glow-peak collocation

International Nuclear Information System (INIS)

Chithambo, M.L.

2016-01-01

The thermoluminescence of SrAl_2O_4:Eu"2"+, Dy"3"+ consists of collocated peaks whereby a dominant component subsumes subsidiary ones to such an extent that they appear as one; Qualitative and quantitative analysis of such cases will be described with suitable illustrative examples. The general features and qualitative kinetics properties of thermoluminescence from SrAl_2O_4:Eu"2"+, Dy"3"+ is reported. Measurements using X-ray excited optical luminescence show that stimulated luminescence from SrAl_2O_4:Eu"2"+, Dy"3"+ has two prominent emission bands, one at 475 nm and a more intense one near 575 nm, studied in this work. There are also weaker intensity emissions at 405, 510, 600 and 660 nm. The natural thermoluminescence measured at 1°C s"-"1 shows three peaks at 74, 170 and 340°C whereas 20 Gy beta-irradiation produces TL dominated by a single peak at 34°C. Analysis of this peak for its order of kinetics produces somewhat inconclusive results. The results of the partial heating procedure T_m - T_s_t_o_p are consistent with both first and second-order kinetics. On the other hand, the position of the peak is independent of dose for several ranges of doses implying that the apparently single peak consists of multiple first-order peaks. Complementary investigations using the fractional glow technique, resolution by isothermal heating and the effect of fading on the peak show that the glow-curve of SrAl_2O_4:Eu"2"+, Dy"3"+ comprises closely collocated thermoluminescence peaks. The implication of such complexity on kinetic analysis on this material and others that share this feature will be discussed. (author)

Towards an automated TLD system that meets international requirements

International Nuclear Information System (INIS)

Boetter-Jensen, L.; Vanamo, V.

1988-01-01

The new recently introduced fully automated TLD system developed by Alnor OY on the basis of the Riso prototype, is intended to meet draft IEC/ISO proposals and ANSI requirements. Part of the system is a personal dosemeter badge and an environmental dosemeter package following ICRU recommendations. The overall system consists of a software-controlled automated reader, a programable irradiator/calibrator, a computer, and dosemeters for environmental, whole body, extremity and clinical applications. The personal TLD badge that contains four TLD pellets is designed to agree with ICRU H p (10) and H s (0.07) quantities for determining dose equivalent. The badge can accommodate a large variety of the most commonly used solid TL dosemeter products. A special effort was put into the evaluation of skin dose by considering the use of graphite-mixed hot-sintered LiF pellets. The TLD system is described and results from a performance test that comprised measurements of photon energy response, angular dependence, and reproducibility are presented

Environmental monitoring with TLD in Costa Rica

International Nuclear Information System (INIS)

Mora, P.; Mora, E.

2003-01-01

Using thermoluminescent dosimeters (Harshaw TLD-200) the first set of costarican data on absorbed doses in air from natural radiation is obtained. During the period from September 1996 to october 2000 eight different sites throughout the country were chosen to instal the TLD stations. Each station had eight cards (five were changed every three months and three changed annually). The dosimeters were read in the Applied Nuclear Physics Laboratory using a 4000 Harshaw reader and with the help a mathematical algorithm and the equipment calibration factors the dose rate in air (nGy h -1 ) was calculated. The national average is 108.9 ± 32.4 nGy h -1 , the lowest values (in nGy h -1 ) were obtain at sea level at Quebrada Honda with 53 ± 11 and the highest values (in nGy h -1 ) at Cartago with 160 ± 19. A slight increase with altitude is observed even though the Cartago station was always the highest. The values found agree with reported worldwide values for environmental doses in air. (Author) [es

Developmental roles of the BMP1/TLD metalloproteinases.

Science.gov (United States)

Ge, Gaoxiang; Greenspan, Daniel S

2006-03-01

-beta-like morphogens BMP2 and 4 and their invertebrate ortholog decapentaplegic, from latent complexes with the vertebrate extracellular antagonist chordin and its invertebrate ortholog short gastrulation (SOG), respectively. The result is formation of the BMP signaling gradients that form the dorsal-ventral axis in embryogenesis. Thus, BMP1/TLD-like proteinases appear to be key to regulating and orchestrating formation of the ECM and signaling by various TGF-beta-like proteins in morphogenetic and homeostatic events. Copyright 2006 Wiley-Liss, Inc.

Properties of alginate fiber spun-dyed with fluorescent pigment dispersion.

Science.gov (United States)

Wang, Ping; Tawiah, Benjamin; Tian, Anli; Wang, Chunxia; Zhang, Liping; Fu, Shaohai

2015-03-15

Spun-dyed alginate fiber was prepared by the spun-dyeing method with the mixture of fluorescent pigment dispersion and sodium alginate fiber spinning solution, and its properties were characterized by SEM, TGA, DSC, and XRD. The results indicate that fluorescent pigment dispersion prepared with esterified poly (styrene-alt maleic acid) had excellent compatibility with sodium alginate fiber spinning solution, and small amount of fluorescent pigment could reduce the viscosity of spun-dyed spinning solutions. SEM photo of spun-dyed alginate fiber indicated that fewer pigment particles deposited on its surface. TGA, DSC, and XRD results suggested that thermal properties and crystal phase of spun-dyed alginate fibers had slight changes compared to the original alginate fibers. The fluorescence intensity of spun-dyed alginate fiber reached its maximum when the content of fluorescent pigment was 4%. The spun-dyed alginate fiber showed excellent rubbing and washing fastness. Copyright © 2014 Elsevier Ltd. All rights reserved.

Defective muscle basement membrane and lack of M-laminin in the dystrophic dy/dy mouse

DEFF Research Database (Denmark)

Xu, H; Christmas, P; Wu, X R

1994-01-01

-linked Duchenne and Becker muscular dystrophies. We have examined M-laminin expression in mice with autosomal recessive muscular dystrophy caused by the mutation dy. The heavy chain of M-laminin was undetectable in skeletal muscle, heart muscle, and peripheral nerve by immunofluorescence and immunoblotting......M-laminin is a major member of the laminin family of basement membrane proteins. It is prominently expressed in striated muscle and peripheral nerve. M-laminin is deficient in patients with the autosomal recessive Fukuyama congenital muscular dystrophy but is normal in patients with the sex...... tissue from dy/dy mice, suggesting that M-laminin heavy-chain mRNA may be produced at very low levels or is unstable. Information about the chromosomal localization of the M heavy-chain in human and mouse suggests that a mutation in the M-chain gene causes the muscular dystrophy in dy/dy mice. The dy...

Luminescent properties in films of ZrO{sub 2}: Dy; Propiedades luminiscentes en peliculas de ZrO{sub 2}: Dy

Energy Technology Data Exchange (ETDEWEB)

Martinez, R. C.; Guzman, J.; Rivera, T.; Ceron, P.; Montes, E.; Guzman, D. [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Unidad Legaria, Av. Legaria No. 694, Col. Irrigacion, 11500 Mexico D. F. (Mexico); Garcia H, M. [UNAM, Instituto de Investigaciones en Materiales, Circuito Exterior, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Falcony, C. [IPN, Centro de Investigacion y de Estudios Avanzados, Apdo. Postal 14-740, 07000 Mexico D. F. (Mexico); Azorin, J., E-mail: rodmarolm@yahoo.com [Universidad Autonoma Metropolitana, Unidad Iztapala, Av. San Rafael Atlixco 186, 09340 Mexico D. F. (Mexico)

2014-08-15

In this work the luminescent characterization of zirconium oxide (ZrO{sub 2}) films impure with dysprosium (Dy{sup +3}) is reported, obtained by means of the ultrasonics spray pyrolysis technique. The films were deposited on glass substrates (Corning), in a temperatures interval of 400 to 550 grades C, using as precursor elements Zirconium oxide chloride octahydrate (ZrOCl{sub 2}·8H{sub 2}O) and Dysprosium tri-chloride (DyCl{sub 3}), dissolved in deionized water, varying the concentration of the contaminated from the 1 to 20 atomic % with relationship to the zirconium in solution. The luminescent characterization was analyzed by means of photoluminescence and thermoluminescence. The photoluminescence results showed a spectrum with three maxima which correspond to the electronic transitions {sup 4}F{sub 9/2} - {sup 6}H{sub 15/2}, {sup 4}F{sub 9/2} - {sup 6}H{sub 13/2} and {sup 4}F{sub 9/2} - {sup 6}H{sub 11/2} characteristics of the Dy{sup 3+} ion. The thermoluminescence (Tl) response when being exposed to a monochrome UV beam in 240 nm showed a wide curve that exhibits a maxim centered in 200 grades C. The Tl response of ZrO{sub 2}:Dy in function of the dose was shown lineal in the interval of 24 mJ/cm{sup 2} to 432 mJ/cm{sup 2}. A study of the repeatability and dissipation of the ZrO{sub 2}:Dy Tl response is included. Considering the shown previous results we can conclude that the ZrO{sub 2} in film form obtained by spray pyrolysis has luminescent properties in 240 nm. (Author)

Facile combustion based engineering of novel white light emitting Zn2TiO4:Dy3+ nanophosphors for display and forensic applications

Directory of Open Access Journals (Sweden)

K.M. Girish

2017-09-01

Full Text Available Nanomaterials find a wide range of applications in surface based nanoscience and technology. To pass high backward encumbrance, low sensitivity, complicated setup and poor universality in traditional methods for the enhancement of latent fingerprints and display applications, we explored the superstructures of dysprosium (Dy3+ doped Zn2TiO4 via a facile solution combustion route. This method offers new potentials in surface-based science comprising display, latent fingerprint, and luminescent ink for anticounterfeiting applications. The characteristic emissions of intra-4f shell Dy3+ cations in blue, yellow and red regions corresponding to 4F9/2 to 6H15/2, 6H13/2, and 6H11/2 transitions respectively, showed white emission, and the Judd–Ofelt theory was used to estimate photometric parameters. The concentration quenching phenomenon is discussed based on possible interactions. Our study reveals a new prospect of using optimized Zn2TiO4:Dy3+ nanophosphors for research in display, fingerprint detection, cheiloscopy, anti-counterfeiting technology, ceramic pigment and forensic applications.

Luminescent processes in SrAl2O4: Eu2+, Dy3+ phosphors exposed to ultraviolet radiation

International Nuclear Information System (INIS)

Arellano T, O.; Castaneda, B.; Pedroza M, M.; Melendrez, R.; Chernov, V.; Barboza F, M.; Yen, W.M.

2006-01-01

The long persistent response of the SrAl 2 O 4 : Eu 2+ , Dy 3+ phosphors has been utilized in the development of new luminescent devices with low voltage requirements, incorporated in luminous paints and emergency light illumination. We have studied the experimental characteristics of thermoluminescence (TL) and afterglow (AG) processes in UV irradiated long persistent phosphors SrAl 2 O 4 : Eu 2+ , Dy 3+ . The TL signal is achieved by thermal stimulation of material and it involves the release of trapped charge carriers in the form of electrons and/or electrons and holes generated by irradiation exposure of the dosimetric materials, while the AG signal is obtained at RT without thermal stimulation. In both cases, the intensity of the response is proportional to the radiation dose. For our UV irradiated SrAl 2 O 4 : Eu 2+ , Dy 3+ samples, the TL glow curve depicted at least five peaks around 318, 424, 457, 488 and 515 K with activation energy values of 0.28, 0.67, 1.00, 1.35 and 1.62 eV, respectively. In this respect, the initial rise method was used to estimate experimentally the peak positions. Then, these experimental data were used as initial values to determine the kinetics parameters through a computer deconvolution and fitting process. Besides, the AG response was analyzed and we found it has at least three exponential processes with different lifetimes around 56, 180 and 1230 s, respectively. In addition, the afterglow dosimetry performance of this SrAl 2 O 4 : Eu 2+ , Dy 3+ phosphor exhibited a linear behavior for the first fifty seconds of ultraviolet irradiation. For higher ultraviolet time exposure the behavior is sub linear with no apparent saturation during ten minutes. The afterglow dosimetry response was performed with a source of 400 nm that corresponds to the main band component of the afterglow excitation spectrum in the 250-500 nm range. The TL glow intensity peaked at 460 K and AG intensity responses are strongly dependents on the excitation

Genotoxic and cytotoxic damage by the therapeutic radiopharmaceutical [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP as in vivo generator system; Dano genotoxico y citotoxico por el radiofarmaco terpeutico [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP como sistema de generador in vivo

Energy Technology Data Exchange (ETDEWEB)

Pedraza L, M; Piedras R, J [Instituto Nacional de Ciencias Medicas y Nutricion, Salvador Zubiran. Vasco. de Quiroga 15, 14000 Mexico D.F. (Mexico); Ferro F, G; Morales R, P [ININ, Km. 36.5 Carretera Mexico-Toluca, Ocoyoacac, 52045 Estado de Mexico (Mexico); Murphy S, E [Hospital Santaelena, Mexico D.F. (Mexico); Hernandez O, O [Escuela Superior de Fisica y Matematicas, IPN, Mexico D.F. (Mexico)

2005-07-01

In patients with leukemias and multiple myeloma, the cure can be obtained to inclination of a bone marrow transplant (m.o.), for that which one is used a combination of external radiotherapy and chemotherapy with the consequent toxicity to healthy organs. The complex [{sup 166}Dy]Dy/{sup 166}Ho-ethylenediaminetetramethylenephosphonate ([{sup 166}Dy]Dy/{sup 166}Ho-EDTMP) it forms a generator system in vivo stable with bony selective likeness in mice therefore, this it could work as a therapeutic radiopharmaceutical for bone marrow ablation. The objective of this original work was to determine the genotoxic and cytotoxic damage produced by the [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP like a generator system in vivo by means of the reticulocytes reduction (RET) and micronucleus elevation in reticulocytes (RET-MN) in peripheral blood and to evaluate its myeloablative potential for histopathologic studies. It was irradiated {sup 166}Dy{sub 2}O{sub 3} enriched and it was add in form {sup 166}DyCI{sub 3} to the EDTMP in a softening media of phosphates (pH 8), the optimal molar relationship {sup 166}Dy: EDTMP was 1.7:1 and the radiochemical purity was evaluated by ITLC. The Dy:EDTMP complexes, non radioactive, its were prepared in the same way with non irradiated dysprosium oxide. A group of BALB/c mice was injected intraperitoneally with the radiopharmaceutical and two groups of control mice were injected with the non radioactive complex and with sodium chloride 0.9% respectively. Before injecting each one of the solutions it was take a basal sample of peripheral blood of the mouse tail and each 48 h post-injection during 12 d. The animals were sacrificed to obtain the organs of interest and to determine the radioactivity in each one. The femur was used for the histopathologic studies. The quantification of the frequency of RET and RET-MN was carried out by flow cytometry of the sanguine samples and the Monte Carlo code MCNP4B for the dosimetry calculations was used. The

Combustion synthesis and characterization of blue long lasting phosphor CaAl2O4: Eu2+, Dy3+ and its novel application in latent fingerprint and lip mark detection

Science.gov (United States)

Sharma, Vishal; Das, Amrita; Kumar, Vijay; Kumar, Vinay; Verma, Kartikey; Swart, H. C.

2018-04-01

This work investigates the structural, optical and photometric characterization of a Eu2+/Dy3+ doped calcium aluminates phosphor (CaAl2O4: Eu2+/Dy3+) for finger and lip print detections. Synthesis of CaAl2O4: Eu2+/Dy3+ (CAED) phosphors were carried out via a combustion synthesis method with urea as a fuel. Eu2+/Dy3+ doped CaAl2O4 phosphors have been studied with X-ray diffraction (XRD, Energy Dispersive X-Ray Spectroscopy Selected Area Diffraction (SAED) and High resolution Transmission Electron Microscope (HR-TEM). The XRD pattern shows that the synthesized Eu2+/Dy3+ doped CaAl2O4 phosphor have a single monoclinic structure and show that the addition of the dopant/co-dopants didn't change the crystal structure. The formation of monoclinic phase was confirmed by the selected area diffraction pattern. The TEM micrograph displays the morphology of the synthesized Eu2+/Dy3+ doped CaAl2O4 phosphors as spherical particles with an average particle size of 33 nm. The optical band gap was calculated using the diffuse reflectance for the synthesized nanophosphor powders. The photoluminescence emission spectra was recorded for the synthesized powder, with an excitation wavelength of 326 nm and the major bands was recorded at 447 nm corresponding to the blue color and two minor bands were recorded at 577 nm and 616 nm. To the best of our knowledge, this work is the first to show the use of CaAl2O4: Eu2+/Dy3+ nanophosphor in developing latent fingerprint and lip print effectively.

Effect of Ligand Substitution around the Dy(III) on the SMM Properties of Dual-Luminescent Zn-Dy and Zn-Dy-Zn Complexes with Large Anisotropy Energy Barriers: A Combined Theoretical and Experimental Magnetostructural Study.

Science.gov (United States)

Costes, Jean Pierre; Titos-Padilla, Silvia; Oyarzabal, Itziar; Gupta, Tulika; Duhayon, Carine; Rajaraman, Gopalan; Colacio, Enrique

2016-05-02

The new dinuclear Zn(II)-Dy(III) and trinuclear Zn(II)-Dy(III)-Zn(II) complexes of formula [(LZnBrDy(ovan) (NO3)(H2O)](H2O)·0.5(MeOH) (1) and [(L(1)ZnBr)2Dy(MeOH)2](ClO4) (3) (L and L(1) are the dideprotonated forms of the N,N'-2,2-dimethylpropylenedi(3-methoxysalicylideneiminato and 2-{(E)-[(3-{[(2E,3E)-3-(hydroxyimino)butan-2-ylidene ]amino}-2,2-dimethylpropyl)imino]methyl}-6-methoxyphenol Schiff base compartmental ligands, respectively) have been prepared and magnetostructurally characterized. The X-ray structure of 1 indicates that the Dy(III) ion exhibits a DyO9 coordination sphere, which is made from four O atoms coming from the compartmental ligand (two methoxy terminal groups and two phenoxido bridging groups connecting Zn(II) and Dy(III) ions), other four atoms belonging to the chelating nitrato and ovanillin ligands, and the last one coming to the coordinated water molecule. The structure of 3 shows the central Dy(III) ion surrounded by two L(1)Zn units, so that the Dy(III) and Zn(II) ions are linked by phenoxido/oximato bridging groups. The Dy ion is eight-coordinated by the six O atoms afforded by two L(1) ligands and two O atoms coming from two methanol molecules. Alternating current (AC) dynamic magnetic measurements of 1, 3, and the previously reported dinuclear [LZnClDy(thd)2] (2) complex (where thd = 2,2,6,6-tetramethyl-3,5-heptanedionato ligand) indicate single molecule magnet (SMM) behavior for all these complexes with large thermal energy barriers for the reversal of the magnetization and butterfly-shaped hysteresis loops at 2 K. Ab initio calculations on 1-3 show a pure Ising ground state for all of them, which induces almost completely suppressed quantum tunnelling magnetization (QTM), and thermally assisted quantum tunnelling magnetization (TA-QTM) relaxations via the first excited Kramers doublet, leading to large energy barriers, thus supporting the observation of SMM behavior. The comparison between the experimental and theoretical

Development of new dosemeters of CaSO_4

International Nuclear Information System (INIS)

Santos, Ana Gabryele M. dos; Junot, Danilo O.; Souza, Divanizia N.

2016-01-01

Thermoluminescent dosimeters (TLDs) are widely used in in vivo dosimetry because of their simple production, viability for dose determination in difficult geometries and their reusability. The motivation of this work was to produce CaSO_4 crystals doped with thulium (Tm) and analyze their thermoluminescent (TL) properties. The crystals were produced by a variation of slow evaporation route, and TL curves showed emission peaks centered around 190 ° C and 320 ° C after irradiation with a "9"0Sr /"9"0Y source. Thermoluminescent properties such as linearity, reproducibility and fading were evaluated. The CaSO_4:Tm samples produced proved feasible for dosimetry purposes. (author)

Optimal selection of TLD chips

International Nuclear Information System (INIS)

Phung, P.; Nicoll, J.J.; Edmonds, P.; Paris, M.; Thompson, C.

1996-01-01

Large sets of TLD chips are often used to measure beam dose characteristics in radiotherapy. A sorting method is presented to allow optimal selection of chips from a chosen set. This method considers the variation

Genotoxic and cytotoxic damage by the therapeutic radiopharmaceutical [166Dy]Dy/166Ho-EDTMP as in vivo generator system

International Nuclear Information System (INIS)

Pedraza L, M.; Piedras R, J.; Ferro F, G.; Morales R, P.; Murphy S, E.; Hernandez O, O.

2005-01-01

In patients with leukemias and multiple myeloma, the cure can be obtained to inclination of a bone marrow transplant (m.o.), for that which one is used a combination of external radiotherapy and chemotherapy with the consequent toxicity to healthy organs. The complex [ 166 Dy]Dy/ 166 Ho-ethylenediaminetetramethylenephosphonate ([ 166 Dy]Dy/ 166 Ho-EDTMP) it forms a generator system in vivo stable with bony selective likeness in mice therefore, this it could work as a therapeutic radiopharmaceutical for bone marrow ablation. The objective of this original work was to determine the genotoxic and cytotoxic damage produced by the [ 166 Dy]Dy/ 166 Ho-EDTMP like a generator system in vivo by means of the reticulocytes reduction (RET) and micronucleus elevation in reticulocytes (RET-MN) in peripheral blood and to evaluate its myeloablative potential for histopathologic studies. It was irradiated 166 Dy 2 O 3 enriched and it was add in form 166 DyCI 3 to the EDTMP in a softening media of phosphates (pH 8), the optimal molar relationship 166 Dy: EDTMP was 1.7:1 and the radiochemical purity was evaluated by ITLC. The Dy:EDTMP complexes, non radioactive, its were prepared in the same way with non irradiated dysprosium oxide. A group of BALB/c mice was injected intraperitoneally with the radiopharmaceutical and two groups of control mice were injected with the non radioactive complex and with sodium chloride 0.9% respectively. Before injecting each one of the solutions it was take a basal sample of peripheral blood of the mouse tail and each 48 h post-injection during 12 d. The animals were sacrificed to obtain the organs of interest and to determine the radioactivity in each one. The femur was used for the histopathologic studies. The quantification of the frequency of RET and RET-MN was carried out by flow cytometry of the sanguine samples and the Monte Carlo code MCNP4B for the dosimetry calculations was used. The radiochemical purity was 99% and in average the specific

Narrow spectral emission CaMoO{sub 4}: Eu{sup 3+}, Dy{sup 3+}, Tb{sup 3+} phosphor crystals for white light emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Khanna, A. [Smart Lighting Engineering Research Center, 110, 8th Street, Troy, New York, 12180 (United States); Electrical, Computer and Systems Engineering Department, Rensselaer Polytechnic Institute, 110, 8th Street, Troy, New York, 12180 (United States); Dutta, P.S., E-mail: duttap@rpi.edu [Smart Lighting Engineering Research Center, 110, 8th Street, Troy, New York, 12180 (United States); Electrical, Computer and Systems Engineering Department, Rensselaer Polytechnic Institute, 110, 8th Street, Troy, New York, 12180 (United States)

2013-02-15

Alkaline earth metal molybdates are promising candidates as a host material for high efficiency narrow spectral emission phosphors. These phosphors could potentially be used for the fabrication of phosphor-converted light emitting diodes (pc-LEDs). Phosphor crystals of calcium molybdate doped with rare earth dopant Ln{sup 3+}(Ln=Eu, Dy, Tb) grown using flux growth method have been shown to exhibit higher excitation efficiency than the powders synthesized by solid-state reaction process. Molybdenum (VI) oxide has been found to be a suitable flux for growing large size optically transparent high quality crystals at a temperature around 1100 Degree-Sign C. Using the excitation wavelengths of 465 nm, 454 nm and 489 nm for CaMoO{sub 4}: Eu{sup 3+}, CaMoO{sub 4}: Dy{sup 3+} and CaMoO{sub 4}: Tb{sup 3+}, respectively, intense emission lines at wavelengths of 615 nm, 575 nm and 550 nm were observed. The optimized doping concentrations of 12%, 2% and 5% for Eu{sup 3+}, Dy{sup 3+} and Tb{sup 3+}, respectively, provided the highest luminescence intensity. - Graphical Abstract: CaMoO{sub 4}: Eu{sup 3+} phosphor crystals grown using a molybdenum (VI) oxide flux exhibited around 1.5 times the emission intensity of powders obtained from solid-state reaction at the same synthesis temperature. These crystals were found to efficiently emit 615 nm red light when excited by near UV light up to a wavelength of 395 nm. Highlights: Black-Right-Pointing-Pointer CaMoO{sub 4}: Ln{sup 3+} (Ln=Eu{sup 3+}, Dy{sup 3+}, Tb{sup 3+}) phosphor crystals were successfully grown using high temperature flux (solutions) containing molybdenum (VI) oxide or lithium chloride. Black-Right-Pointing-Pointer Narrow spectral emission at 615 nm, 575 nm and 550 nm, respectively, was observed from CaMoO{sub 4}: Ln{sup 3+} (Ln=Eu{sup 3+}, Dy{sup 3+}, Tb{sup 3+}) phosphor crystals. Black-Right-Pointing-Pointer The optimized doping concentrations of Eu{sup 3+}, Dy{sup 3+}, Tb{sup 3+} in CaMoO{sub 4} for highest

Síntesis hidrotermal de monocristales LnMn2O5 (Ln= Y, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho y Er

Directory of Open Access Journals (Sweden)

Señarís Rodríguez, M. A.

2008-08-01

Full Text Available Ten single crystals of the series LnMn2O5 (Ln= Y, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho and Er were synthesized by hydrothermal synthesis in a single step and without subsequent thermal treatments from aqueous solutions of metals salts at 240 ºC. The obtained single crystals have a size of various micrometers and their morphology changes throughout the serie: they are polygonal in the case of the compounds with Ln= Pr, Nd, Sm, Eu and Gd and needle-like in the case of the compounds with Ln= Y, Tb, Dy, Ho and Er. After the analysis of the obtained products employing different conditions of synthesis we attributed the different morphology to a greater growth rate along the c axis when the smaller ions (Y, Tb, Dy, Ho y Er are involved, due to their better adaptation to the compound’s crystal structure.Se han conseguido preparar monocristales de 10 óxidos mixtos de la serie LnMn2O5 (Ln= Y, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho y Er mediante síntesis hidrotermal optimizada, en un único paso y sin tratamientos térmicos posteriores partiendo de las correspondientes sales metálicas en disolución acuosa a 240 ºC. Los monocristales obtenidos son relativamente grandes, de varias micras y su morfología varía a lo largo de la serie: es poligonal en el caso de los compuestos de los lantánidos del inicio de la serie (Ln= Pr, Nd, Sm, Eu y Gd y acicular en el caso de los compuestos de Y y de los lantánidos del final de la serie (Ln= Tb, Dy, Ho y Er. Tras el análisis de los productos obtenidos empleando distintas condiciones de síntesis atribuimos la diferente morfología a una mayor velocidad de crecimiento cristalino a lo largo del eje c cuando intervienen los iones más pequeños (Y, Tb, Dy, Ho y Er debido a la mejor adaptación de éstos últimos a la estructura cristalina del compuesto.

Size-dependent structure and magnetic properties of DyMnO3 nanoparticles

International Nuclear Information System (INIS)

Cai, Xuan; Shi, Lei; Zhou, Shiming; Zhao, Jiyin; Guo, Yuqiao; Wang, Cailin

2014-01-01

The structure and magnetic properties of orthorhombic DyMnO 3 nanoparticles with different particle sizes are investigated in this paper. With decreasing particle size, all the lattice parameters a, b, and c gradually decrease, whereas the orthorhombic distortion increases. Magnetic measurements reveal that the antiferromagnetic interaction of Mn ions is weakened due to the decrease in Mn-O-Mn bond angle. Above a critical field H*, DyMnO 3 undergoes a field-induced metamagnetic transition at 4 K, which is related to the spin reversal of Dy moments. The critical field H* increases monotonically with size reduction, indicating an enhancement of the antiferromagnetic interaction of Dy ions due to the decreased distance between rare earth ions. The magnetization at 4 K and 5 T, i.e., M(4 K, 5 T) shows a non-monotonic variation with particle size d, i.e., M(4 K, 5 T) initially increases with size reduction but decreases again for d < 68 nm. A modified core-shell model, in which the ferromagnetic ordering (Dy magnetic structure) and antiferromagnetic ordering (Mn magnetic structure) coexist in the core, is proposed to explain this behavior.

Ten years experience with a large computerized TLD-personnel monitoring system

International Nuclear Information System (INIS)

Duftschmid, K.E.

1986-01-01

It is now ten years since our Institute for Radiation Protection has fully replaced its filmdosimetry service by a computerized automated TLD system. Presently more than 13000 radiation workers are monthly monitored by three automated TLD readers linked to the computer center. The paper describes system hardware and software and experience gained in long-term routine operation. In particular the introduction of the new ICRU quantities for personnel dosimetry in the existing TLD system is discussed. (Author)

Positional glow curve simulation for thermoluminescent detector (TLD) system design

International Nuclear Information System (INIS)

Branch, C.J.; Kearfott, K.J.

1999-01-01

Multi- and thin element dosimeters, variable heating rate schemes, and glow-curve analysis have been employed to improve environmental and personnel dosimetry using thermoluminescent detectors (TLDs). Detailed analysis of the effects of errors and optimization of techniques would be highly desirable. However, an understanding of the relationship between TL light production, light attenuation, and precise heating schemes is made difficult because of experimental challenges involved in measuring positional TL light production and temperature variations as a function of time. This work reports the development of a general-purpose computer code, thermoluminescent detector simulator, TLD-SIM, to simulate the heating of any TLD type using a variety of conventional and experimental heating methods including pulsed focused or unfocused lasers with Gaussian or uniform cross sections, planchet, hot gas, hot finger, optical, infrared, or electrical heating. TLD-SIM has been used to study the impact on the TL light production of varying the input parameters which include: detector composition, heat capacity, heat conductivity, physical size, and density; trapped electron density, the frequency factor of oscillation of electrons in the traps, and trap-conduction band potential energy difference; heating scheme source terms and heat transfer boundary conditions; and TL light scatter and attenuation coefficients. Temperature profiles and glow curves as a function of position time, as well as the corresponding temporally and/or spatially integrated glow values, may be plotted while varying any of the input parameters. Examples illustrating TLD system functions, including glow curve variability, will be presented. The flexible capabilities of TLD-SIM promises to enable improved TLD system design

Magnetic and photoluminescence properties of Fe{sub 3}O{sub 4}-SiO{sub 2}-YP{sub 1-x}V{sub x}O{sub 4}:Dy{sup 3+} nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Shi Jianhui; Liu Deming; Tong Lizhu; Yang Xuwei [College of Chemistry, Jilin University, Changchun, 130012 (China); Yang Hua, E-mail: huayang86@sina.com [College of Chemistry, Jilin University, Changchun, 130012 (China)

2011-10-20

Highlights: > Bifunctional Fe{sub 3}O{sub 4}-SiO{sub 2}-YP{sub 0.1}V{sub 0.9}O{sub 4}:Dy{sup 3+} nanocomposite was fabricated by a sol-gel method. > The structure, luminescent and magnetic properties were characterized of the nanocomposites. > It is shown that the nanocomposite with a core-shell structure has excellent fluorescent and magnetic properties. > The effects of the magnetic field on the luminescence properties of nanocomposite were discussed. - Abstract: In this paper, we report on the bifunctional Fe{sub 3}O{sub 4}-SiO{sub 2}-YP{sub 0.1}V{sub 0.9}O{sub 4}:Dy{sup 3+} nanocomposites were prepared by the solvothermal method and sol-gel method. The structure, photoluminescence (PL) and magnetic properties of the nanocomposites were characterized by means of X-ray diffraction, scanning electron microscope, transmission electron microscope, PL excitation and emission spectra and vibration sample magnetometry. It is shown that Fe{sub 3}O{sub 4}-SiO{sub 2}-YP{sub 0.1}V{sub 0.9}O{sub 4}:Dy{sup 3+} nanocomposites with a core-shell structure present excellent fluorescent and magnetic properties. Additionally, the effects of the magnetic field on the luminescence properties of nanocomposites were discussed.

Effective dose assessment in the maxillofacial region using thermoluminescent (TLD) and metal oxide semiconductor field-effect transistor (MOSFET) dosemeters: a comparative study.

Science.gov (United States)

Koivisto, J; Schulze, D; Wolff, J; Rottke, D

2014-01-01

The objective of this study was to compare the performance of metal oxide semiconductor field-effect transistor (MOSFET) technology dosemeters with thermoluminescent dosemeters (TLDs) (TLD 100; Thermo Fisher Scientific, Waltham, MA) in the maxillofacial area. Organ and effective dose measurements were performed using 40 TLD and 20 MOSFET dosemeters that were alternately placed in 20 different locations in 1 anthropomorphic RANDO(®) head phantom (the Phantom Laboratory, Salem, NY). The phantom was exposed to four different CBCT default maxillofacial protocols using small (4 × 5 cm) to full face (20 × 17 cm) fields of view (FOVs). The TLD effective doses ranged between 7.0 and 158.0 µSv and the MOSFET doses between 6.1 and 175.0 µSv. The MOSFET and TLD effective doses acquired using four different (FOV) protocols were as follows: face maxillofacial (FOV 20 × 17 cm) (MOSFET, 83.4 µSv; TLD, 87.6 µSv; -5%); teeth, upper jaw (FOV, 8.5 × 5.0 cm) (MOSFET, 6.1 µSv; TLD, 7.0 µSv; -14%); tooth, mandible and left molar (FOV, 4 × 5 cm) (MOSFET, 10.3 µSv; TLD, 12.3 µSv; -16%) and teeth, both jaws (FOV, 10 × 10 cm) (MOSFET, 175 µSv; TLD, 158 µSv; +11%). The largest variation in organ and effective dose was recorded in the small FOV protocols. Taking into account the uncertainties of both measurement methods and the results of the statistical analysis, the effective doses acquired using MOSFET dosemeters were found to be in good agreement with those obtained using TLD dosemeters. The MOSFET dosemeters constitute a feasible alternative for TLDs for the effective dose assessment of CBCT devices in the maxillofacial region.

Self-shielding factors for TLD-600 and TLD-100 in an isotropic flux of thermal neutrons

International Nuclear Information System (INIS)

Horowitz, Y.S.; Dubi, A.; Ben Shahar, B.

1976-01-01

The applications of lithium fluoride thermoluminescent dosemeters in mixed n-γ environments, and the dependence of LiF-TL on linear energy transfer are both topics of current interest. Monte Carlo calculations have therefore been carried out to determine the thermal neutron absorption probability (and consequently the self-shielding factor) for an isotropic flux of neutrons impinging on different sized cylindrical samples of LiF TLD-100 and TLD-600. The calculations were performed for cylinders of radius up to 10 cm and heights of 0.1 to 1.5 cm. The Monte Carlo results were found to be significantly different from the analytic calculations for infinitely long cylinders, but, as expected, converged to the same value for (r/h) << 1. (U.K.)

Steric hindrances create a discrete linear Dy4 complex exhibiting SMM behaviour.

Science.gov (United States)

Lin, Shuang-Yan; Zhao, Lang; Ke, Hongshan; Guo, Yun-Nan; Tang, Jinkui; Guo, Yang; Dou, Jianmin

2012-03-21

Two linear tetranuclear lanthanide complexes of general formula [Ln(4)(L)(2)(C(6)H(5)COO)(12)(MeOH)(4)], where HL = 2,6-bis((furan-2-ylmethylimino)methyl)-4-methylphenol, () and Ln(III) = Dy(III) (1) and Gd(III) (2), have been synthesized and characterized. The crystal structural analysis demonstrates that two Schiff-base ligands inhibit the growth of benzoate bridged 1D chains, leading to the isolation of discrete tetranuclear complexes due to their steric hindrances. Every Ln(III) ion is coordinated by eight donor atoms in a distorted bicapped trigonal-prismatic arrangement. Alternating current (ac) susceptibility measurements of complex 1 reveal a frequency- and temperature-dependent out-of-phase signal under zero dc field, typical of single-molecule magnet (SMM) behaviour with an anisotropic barrier Δ(eff) = 17.2 K.

Introducing 2D barcode on TLD cards - a step towards automation in personnel monitoring

International Nuclear Information System (INIS)

Ajoy, K.C.; Dhanasekaran, A.; Annalakshmi, O; Rajagopal, V.; Santhanam, R.; Jose, M.T.

2018-01-01

As part of personnel monitoring services, TLD lab, RSD, IGCAR issues and receives large numbers of TLD cards every month, for use by occupational workers belonging to various hot facilities at Kalpakkam. Considering the nature of the work being manual, routine, labour intensive and being prone for human errors, introducing automation would be necessary at the TLD lab as well as at the user facility. This requires identification of the individual components of the TLD and embed them with unique identification for the system to accomplish the task. The paper discusses the automation part related to the TLD cards

KCa4(BO33:Ln3+ (Ln = Dy, Eu, Tb phosphors for near UV excited white–light–emitting diodes

Directory of Open Access Journals (Sweden)

Allu Amarnath Reddy

2013-02-01

Full Text Available A series of doped KCa4(BO33:Ln3+ (Ln: Dy, Eu and Tb compositions were synthesized by solid–state reaction method and their photoluminescent properties were systematically investigated to ascertain their suitability for application in white light emitting diodes. The X–ray diffraction (XRD and nuclear magnetic resonance (MAS–NMR data indicates that Ln3+–ions are successfully occupied the non–centrosymmetric Ca2+ sites, in the orthorhombic crystalline phase of KCa4(BO33 having space group Ama2, without affecting the boron chemical environment. The present phosphor systems could be efficiently excitable at the broad UV wavelength region, from 250 to 350 nm, compatible to the most commonly available UV light–emitting diode (LED chips. Photoluminescence studies revealed optimal near white–light emission for KCa4(BO33 with 5 wt.% Dy3+ doping, while warm white–light (CIE; X = 0.353, Y = 0.369 is obtained at 1wt.% Dy3+ ion concentration. The principle of energy transfer between Eu3+ and Tb3+ also demonstrates the potential white–light from KCa4(BO33:Eu3+,Tb3+ phosphor. Whereas, single Tb3+ and Eu3+–doped systems showed bright green (Tb3+ and red (Eu3+ emissions, respectively. Having structural flexibility along with remarkable chemical/thermal stability and suitable quantum efficiency these phosphors can be promising candidates as white–light–emitter for near UV LEDs.

Next Generation Model 8800 Automatic TLD Reader

International Nuclear Information System (INIS)

Velbeck, K.J.; Streetz, K.L.; Rotunda, J.E.

1999-01-01

BICRON NE has developed an advanced version of the Model 8800 Automatic TLD Reader. Improvements in the reader include a Windows NT TM -based operating system and a Pentium microprocessor for the host controller, a servo-controlled transport, a VGA display, mouse control, and modular assembly. This high capacity reader will automatically read fourteen hundred TLD Cards in one loading. Up to four elements in a card can be heated without mechanical contact, using hot nitrogen gas. Improvements in performance include an increased throughput rate and more precise card positioning. Operation is simplified through easy-to-read Windows-type screens. Glow curves are displayed graphically along with light intensity, temperature, and channel scaling. Maintenance and diagnostic aids are included for easier troubleshooting. A click of a mouse will command actions that are displayed in easy-to-understand English words. Available options include an internal 90 Sr irradiator, automatic TLD calibration, and two different extremity monitoring modes. Results from testing include reproducibility, reader stability, linearity, detection threshold, residue, primary power supply voltage and frequency, transient voltage, drop testing, and light leakage. (author)

Field induced 4f5d [Re(salen)]2O3[Dy(hfac)3(H2O)]2 single molecule magnet.

Science.gov (United States)

Pointillart, Fabrice; Bernot, K; Sessoli, R; Gatteschi, D

2010-05-03

The reaction between the mononuclear [ReO(salen)(OMe)] (salen(2-) = N,N'-ethan-1,2-diylbis(salicylidenamine) dianion) and Dy(hfac)(3).2H(2)O (hfac(-) = 1,1,1,5,5,5-hexafluoroacetylacetonate anion) complexes lead to the formation of a compound with the formula {[Re(salen)](2)O(3)[Dy(hfac)(3)(H(2)O)](2)}(CHCl(3))(2)(CH(2)Cl(2))(2) noted (Dy(2)Re(2)). This compound has been characterized by single crystal and powder X-ray diffraction and has been found isostructural to the Y(III) derivative (Y(2)Re(2)) that we previously reported. The cyclic voltammetry demonstrates the redox activity of the system. The characterization of both static and dynamic magnetic properties is reported. Static magnetic data has been analyzed after the cancellation of the crystal field contribution by two different methods. Weak ferromagnetic exchange interactions between the Dy(III) ions are highlighted. The compound Dy(2)Re(2) displays slow relaxation of the magnetization when an external magnetic field is applied. Alternating current susceptibility shows a thermally activated behavior with pre-exponential factors of 7.13 (+/-0.10) x 10(-6) and 5.76 (+/-0.27) x 10(-7) s, and energy barriers of 4.19 (+/-0.02) and 8.52 (+/-0.55) K respectively for low and high temperature regimes.

Photoluminescence and phosphorescence properties of MAl2O4:Eu2+, Dy3+ (M=Ca, Ba, Sr) phosphors prepared at an initiating combustion temperature of 500 deg. C

International Nuclear Information System (INIS)

Mothudi, B.M.; Ntwaeaborwa, O.M.; Botha, J.R.; Swart, H.C.

2009-01-01

Eu 2+ and Dy 3+ co-doped calcium aluminate, barium aluminate and strontium aluminate phosphors were synthesized at an initiating combustion temperature of 500 deg. C using urea as an organic fuel. The crystallinity of the phosphors was investigated by using X-ray diffraction (XRD) and the morphology was determined by a scanning electron microscope (SEM). The low temperature monoclinic structure for both CaAl 2 O 4 and SrAl 2 O 4 and the hexagonal structure of BaAl 2 O 4 were observed. The effect of the host materials on the photoluminescence (PL) and phosphorescence properties were investigated by using a He-Cd Laser and a Cary Eclipse fluorescence spectrophotometer, respectively. The broad band emission spectra observed at 449 nm for CaAl 2 O 4 :Eu 2+ , Dy 3+ , 450 nm (with a shoulder-peak at 500 nm) for BaAl 2 O 4 :Eu 2+ , Dy 3+ and 528 nm for SrAl 2 O 4 :Eu 2+ , Dy 3+ are attributed to the 4f 6 5d 1 to 4f 7 transition in the Eu 2+ ion in the different hosts.

Luminescent properties in films of ZrO2: Dy

International Nuclear Information System (INIS)

Martinez, R. C.; Guzman, J.; Rivera, T.; Ceron, P.; Montes, E.; Guzman, D.; Garcia H, M.; Falcony, C.; Azorin, J.

2014-08-01

In this work the luminescent characterization of zirconium oxide (ZrO 2 ) films impure with dysprosium (Dy +3 ) is reported, obtained by means of the ultrasonics spray pyrolysis technique. The films were deposited on glass substrates (Corning), in a temperatures interval of 400 to 550 grades C, using as precursor elements Zirconium oxide chloride octahydrate (ZrOCl 2 ·8H 2 O) and Dysprosium tri-chloride (DyCl 3 ), dissolved in deionized water, varying the concentration of the contaminated from the 1 to 20 atomic % with relationship to the zirconium in solution. The luminescent characterization was analyzed by means of photoluminescence and thermoluminescence. The photoluminescence results showed a spectrum with three maxima which correspond to the electronic transitions 4 F 9/2 - 6 H 15/2 , 4 F 9/2 - 6 H 13/2 and 4 F 9/2 - 6 H 11/2 characteristics of the Dy 3+ ion. The thermoluminescence (Tl) response when being exposed to a monochrome UV beam in 240 nm showed a wide curve that exhibits a maxim centered in 200 grades C. The Tl response of ZrO 2 :Dy in function of the dose was shown lineal in the interval of 24 mJ/cm 2 to 432 mJ/cm 2 . A study of the repeatability and dissipation of the ZrO 2 :Dy Tl response is included. Considering the shown previous results we can conclude that the ZrO 2 in film form obtained by spray pyrolysis has luminescent properties in 240 nm. (Author)

Cytotoxic and genotoxic effect of the [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP in vivo generator system in mice

Energy Technology Data Exchange (ETDEWEB)

Pedraza-Lopez, Martha [Departamento de Medicina Nuclear, Instituto Nacional de Ciencias Medicas y Nutricion, Salvador Zubiran, Delegacion Tlalpan, Mexico DF 14000 (Mexico); Ferro-Flores, Guillermina [Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca, Ocoyoacac, Estado de Mexico, CP 52045 (Mexico); Arteaga de Murphy, Consuelo [Departamento de Medicina Nuclear, Instituto Nacional de Ciencias Medicas y Nutricion, Salvador Zubiran, Delegacion Tlalpan, Mexico DF 14000 (Mexico)]. E-mail: consuelo_murphy@yahoo.com.mx; Morales-Ramirez, Pedro [Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca, Ocoyoacac, Estado de Mexico, CP 52045 (Mexico); Piedras-Ross, Josefa [Departamento de Medicina Nuclear, Instituto Nacional de Ciencias Medicas y Nutricion, Salvador Zubiran, Delegacion Tlalpan, Mexico DF 14000 (Mexico); Murphy-Stack, Eduardo [Hospital Santaelena, Mexico DF (Mexico); Hernandez-Oviedo, Omar [Escuela Superior de Fisica y Matematicas, IPN, Mexico DF (Mexico)

2004-11-01

Multiple myeloma and other hematological malignancies have been treated by myeloablative radiotherapy/chemotherapy and subsequent stem cell transplantation. [{sup 166}Dy]Dy/{sup 166}Ho-ethylenediaminetetramethylene phosphonate (EDTMP) forms a stable in vivo generator system with selective skeletal uptake in mice; therefore, it could work as a potential and improved agent for marrow ablation. Induced bone marrow cytotoxicity and genotoxicity are determined by the reduction of reticulocytes (RET) and elevation of micronucleated reticulocyte (MN-RET) in peripheral blood and ablation by bone marrow histological studies. The aim of this study was to determine the bone marrow cytotoxic and genotoxic effect of the [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP in vivo generator system in mice and to evaluate by histopathology its myeloablative potential. Enriched {sup 166}Dy{sub 2}O{sub 3} was irradiated and [{sup 166}Dy]DyCl{sub 3} was added to EDTMP in phosphate buffer (pH 8.0) in a molar ratio of 1:1.75. QC was determined by TLC. Dy-EDTMP complex was prepared the same way with nonirradiated dysprosium oxide. A group of BALB/c mice were intraperitoneally injected with the radiopharmaceutical and two groups of control animals were injected with the cold complex and with 0.9% sodium chloride, respectively. A blood sample was taken at the beginning of the experiments and every 48 h for 12 days postinjection. The animals were sacrificed, organs of interest taken out and the radioactivity determined. The femur was used for histological studies. Flow cytometry analysis was used to quantify the frequency of RET and MN-RET in the blood samples. The MCNP4B Monte Carlo computer code was used for dosimetry calculations. Radiochemical purity was 99% and the mean specific activity was 1.3 MBq/mg. The RET and MN-RET frequency were statistically different in the treatment at the end of the 12-day period demonstrating cytotoxicity and genotoxicity induced by the in vivo generator system. The

How to diagnose any type of TLD Reader?

International Nuclear Information System (INIS)

Rodriguez, Manuel Lopez; Garcia, Jose A. Tamayo; Gil, Alex Vergara; Lores, Stefan Gutierrez; Acosta, Andry Romero; Villanueva, Gilberto Alonso

2013-01-01

The acquisition of know how of practical experiences obtained in the repair and maintenance of readers TLD RADOS for five years of work and the request by the International Atomic Energy for signing new Research Contracts (CRP), made possible the CRP 13328, in which the specialist is committed in the course of a year, to deliver educational software in order to train personnel associated with the operation of the TLD readers RADOS. Due to the importance of continuous transfer of knowledge for new generations of technicians and specialists who join our laboratories, the idea came when the first interactive CD that grouped 19 videos, divided into three blocks was ready: learning, repair and maintenance; it was suggested to expand the training for any TLD reader. Thus a much more complete than the first version package emerged. 7 cases were subsequently published in an IAEA TECDOC, 1599 were included

Phosphors doped with Dy3+ and Gd3+ for lighting

International Nuclear Information System (INIS)

Su, Q; Pei, Z.; Zeng, Q.; Chi, L.

1998-01-01

Full text: Some heavy lanthanide ions with even atomic number such as Dy 3+ and Gd 3+ are abundant in the ion adsorption type deposit of China. Their price is cheap and they have specific spectroscopic properties which can be used as phosphors. Dy 3i on has two dominant bands in the emission spectrum. The yellow band (575 nm) corresponds to the hypersensitive transition 4 F 9/2 → 6 H 13/2 (ΔL=2, ΔJ=2), and the blue band (485 nm) corresponds to the 4 F 9/2 → 6 H 15/2 transition. Factors which influence on the yellow- to-blue intensity ratio (Y/B) were investigated. Adjusting to a suitable Y/B, Dy 3+ will emit white light with high colour temperature and can be used for lighting. But Dy 3+ ion has only narrow excitation bands of f-f transitions ranging from 300-500 nm, no broad excitation band such as charge transfer band or f-d transition band exists in the UV region 200-300 nm. Hence its luminescent efficiency is low when it is excited by UV radiation emitted from the mercury plasma. This is one of the drawbacks to its use as lamp phosphor. However, this can be overcome by sensitisation with Gd 3+ , Pb 2+ or other sensitisers such as vanadate shown in this report. Gd 3+ is not only a good matrix, but also a good sensitiser. Using its 8 S 7/2 → 6 D, 6 I and 6 P transitions, the UV excitation energy can be absorbed and transferred to the activator such as Dy 3+ . Therefore, in some cases Gd 3+ is better than Y 3+ which is optical inert as a matrix. For the phosphor Ca 1.96 Pb 0.04 RE 7.9 Dy 0.1 (SiO 4 ) 6 O 2 prepared by sol-gel method, the intensity of Dy 3+ in the Gd 3+ compound (RE=Gd 3+ ) is six times that in the Y 3+ compound. Some new phosphors doped with Dy 3+ and Gd 3+ prepared in our laboratory are reported

Analysis of read-out heating rate effects on the glow peaks of TLD-100 using WinGCF software

Energy Technology Data Exchange (ETDEWEB)

Bauk, Sabar, E-mail: sabar@usm.my [Physics Section, School of Distance Education, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Hussin, Siti Fatimah [School of Physics, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Alam, Md. Shah [Physics Section, School of Distance Education, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Physics Department, Shahjalal University of Science and Technology, Sylhet (Bangladesh)

2016-01-22

This study was done to analyze the effects of the read-out heating rate on the LiF:Mg,Ti (TLD-100) thermoluminescent dosimeters (TLD) glow peaks using WinGCF computer software. The TLDs were exposed to X-ray photons with a potential difference of 72 kVp and 200 mAs in air and were read-out using a Harshaw 3500 TLD reader. The TLDs were read-out using four read-out heating rates at 10, 7, 4 and 1 °C s{sup −1}. It was observed that lowering the heating rate could separate more glow peaks. The activation energy for peak 5 was found to be lower than that for peak 4. The peak maximum temperature and the integral value of the main peak decreased as the heating rate decreases.

Minimizing TLD-DRD differences

International Nuclear Information System (INIS)

Riley, D.L.; McCoy, R.A.; Connell, W.D.

1987-01-01

When substantial differences exist in exposures recorded by TLD's and DRD's, it is often necessary to perform an exposure investigation to reconcile the difference. In working with several operating plants, the authors have observed a number of causes for these differences. This paper outlines these observations and discusses procedures that can be used to minimize them

Electronic structure and magnetic properties of Dy adatom on Ir surface

Science.gov (United States)

Shick, A. B.; Lichtenstein, A. I.

2018-05-01

The electronic structure and magnetism of individual Dy atom adsorbed on the (1 1 1) surface of Ir is investigated using the combination of the density functional theory with the Hubbard-I approximation to the Anderson impurity model (DFT + HIA). The Dy3+ adatom is found magnetic with the magnetic moment of 9.35μB in the external magnetic field. The spin and orbital magnetic moments, and their ratio are evaluated, and compared with the X-ray magnetic circular dichroism data. The positive magnetic anisotropy energy of ≈ 1.3 meV determines the out-of-plane orientation of the Dy adatom magnetic moment. The role of 5d-4f interorbital exchange polarization in modification of the 4f shell energy spectrum is emphasized. We predict the Dy magnetization to drop by the factor of three with switching off the external magnetic field.

Effect of annealing on the structural, optical and emissive properties of SrWO4:Ln3+ (Dy3+, Eu3+ and Sm3+) nanoparticles

Science.gov (United States)

Maheshwary; Singh, B. P.; Singh, R. A.

2016-01-01

Lanthanide ions, Ln3+ (Dy3+, Eu3+ and Sm3+) doped SrWO4 nanoparticles were synthesized using ethylene glycol (EG) as a capping agent as well as reaction medium. The X-ray diffraction (XRD) study reveals that all the Ln3+ (Dy3+, Eu3+ and Sm3+) doped samples are well crystalline in nature with a tetragonal scheelite structure of SrWO4 phase. TG study reveals that the nanophosphors are thermally stable. Fourier transform infrared spectroscopy (FTIR) and Raman spectroscopy techniques were used to obtain the information about internal and external vibrational modes present in the SrWO4 structure. Optical properties were investigated using UV-vis and photoluminescence (PL) spectroscopy. The average crystallite size was calculated using Debye-Scherrer's for as-prepared and 800 °C annealed samples and is found to be in the range of ∼35-70 nm. The luminescence intensity of Eu3+ doped SrWO4 nanoparticles under 364 nm excitation wavelength reveals that 5D0 → 7F2 transition at ∼613 nm (red) is more prominent than that of 5D0 → 7F1 transition at ∼590 nm (orange). Also upon excitation by UV radiation, the SrWO4:Dy3+ phosphor shows the yellow and blue transition lines appearing at ∼572 and 484 nm which are the characteristic electronic transitions of 4F9/2-6H13/2 and 4F9/2-6H15/2 emission line of Dy3+, respectively. Also Sm3+ doped SrWO4 nanophosphor shows its characteristic emission lines in the range of 550-720 nm, corresponding to 4G5/2 → 6HJ (J = 5/2, 7/2, 9/2 and 11/2) transitions of Sm3+ ions. The predominant orange red color can be attributed to 4G5/2 → 6H9/2 located at ∼642 nm. This is related to the polarizing effect due to the energy transfer from WO42- to the Eu3+, Dy3+ and Sm3+ sites, respectively. Effect of annealing on the photoluminescence properties of samples has been studied and it was found that luminescence intensity increases up to ∼3 times on heating the samples at 800 °C. This may be due to reduction in non-radiative decay channels

Synthesis, luminescence, and energy-transfer properties of β-Na2Ca4(PO4)2(SiO4):A (A = Eu(2+), Dy(3+), Ce(3+)/Tb(3+)) phosphors.

Science.gov (United States)

Li, Kai; Shang, Mengmeng; Geng, Dongling; Lian, Hongzhou; Zhang, Yang; Fan, Jian; Lin, Jun

2014-07-07

A series of β-Na2Ca4(PO4)2(SiO4) (β-NCPS):A (A = Eu(2+), Dy(3+), Ce(3+)/Tb(3+)) phosphors were prepared via a high-temperature solid-state reaction route. The X-ray diffraction, Fourier transform infrared, photoluminescence (PL), cathodoluminescence (CL) properties, fluorescent lifetimes, and absolute quantum yield were exploited to characterize the samples. Under UV radiation, the β-NCPS:Eu(2+) phosphors present bright green emissions, and the β-NCPS:Ce(3+) phosphors show strong blue emissions, which are attributed to their 4f(6)5d(1) → 4f(7) and 5d-4f allowed transitions, respectively. The β-NCPS:Ce(3+), Tb(3+) phosphors display intense tunable color from blue to green and high absolute quantum yields (81% for β-NCPS:0.12Ce(3+) and 83% for β-NCPS:0.12Ce(3+), 0.08Tb(3+)) when excited at 365 nm. Simultaneously, the energy transfer from Ce(3+) to Tb(3+) ions is deduced from the spectral overlap between Ce(3+) emission and Tb(3+) excitation spectra and demonstrated by the change of emission spectra and decay lifetimes. Moreover, the energy-transfer mechanism from Ce(3+) to Tb(3+) ions is confirmed to be exchange interaction according to the discussion of expression from Dexter and Reisfeld. Under a low-voltage electron-beam excitation, the β-NCPS:A (A = Eu(2+), Dy(3+), Ce(3+)/Tb(3+)) phosphors exhibit their characteristic emissions, and the emission profiles of β-NCPS:Ce(3+),Tb(3+) phosphors are obviously different from those of the PL spectra; this difference might be ascribed to their different luminescence mechanisms. These results in PL and CL properties suggest that β-NCPS:A (A = Eu(2+), Dy(3+), Ce(3+)/Tb(3+)) phosphors are potential candidates for solid-state lighting and field-emission displays.

The study of new calibration features in the Harshaw TLD system

International Nuclear Information System (INIS)

Luo, L. Z.

2007-01-01

The Harshaw TLD system has three key calibration procedures: the Reader, the Dosemeter and the Algorithm. These functions must be properly calibrated for the system to achieve the optimum results. For the conventional reader and dosemeter calibration, Harshaw TLD recommends a pre-fade and a post-fade of 24-48 h when calibrating the system for LiF:Mg,Ti type dosemeter. It is also recommended that keeping the fade time consistent is important to maintain the quality of the system performance. In recent years, new calibration features have been introduced into the Harshaw TLD models 6600 and 8800 operating systems. These new features are Auto Calibration, Auto QC and Auto Blank, and they give the user the ability to set up the clear-expose-read process to be performed automatically in a sequence for each dosemeter. This saves processing time and keeps the fade time the same. However, since the fade time is near zero, will it affect the TLD system calibration factors? What should the user expect? This paper presents a study of the effect of Auto Calibration/Auto QC to the TLD operation. (authors)

Modulating the single-molecule magnet behaviour in phenoxo-O bridged Dy2 systems via subtle structural variations

Science.gov (United States)

Wang, Wen-Min; Zhao, Xiao-Yu; Qiao, Hui; Bai, Li; Han, Hong-Fei; Fang, Ming; Wu, Zhi-Lei; Zou, Ji-Yong

2017-09-01

In search of simple approaches to rationally modulate the single-molecule magnet behaviour in polynuclear lanthanide compound, a new system containing two structurally closely related dinuclear dysprosium complexes, namely [Dy2(hfac)4L2] (1) and [Dy2(hfac)4L‧2] (2) (hfac = hexafluoroacetylacetonate, HL = 2-[4-methylaniline-imino]methyl]-8-hydroxyquinoline and HL' = 2-[(3,4-dimethylaniline)-imino]methyl]-8-hydroxyquinoline), are successfully synthesized and the structure-dependent magnetic properties are investigated. The two Dy2 compounds display only slight variations in the coordination geometries of the center Dy(III) ion but display remarkably different single-molecule magnet behaviors with the anisotropic barriers (ΔE/kB) of 9.91 K for 1 and 20.57 K for 2. The different magnetic relaxation behaviors of the two Dy2 complexes mainly originate from the different chemical environments of the central DyIII ions.

Influence of Dy in solid solution on the degradation behavior of binary Mg-Dy alloys in cell culture medium.

Science.gov (United States)

Yang, Lei; Ma, Liangong; Huang, Yuanding; Feyerabend, Frank; Blawert, Carsten; Höche, Daniel; Willumeit-Römer, Regine; Zhang, Erlin; Kainer, Karl Ulrich; Hort, Norbert

2017-06-01

Rare earth element Dy is one of the promising alloying elements for magnesium alloy as biodegradable implants. To understand the effect of Dy in solid solution on the degradation of Mg-Dy alloys in simulated physiological conditions, the present work studied the microstructure and degradation behavior of Mg-Dy alloys in cell culture medium. It is found the corrosion resistance enhances with the increase of Dy content in solid solution in Mg. This can be attributed to the formation of a relatively more corrosion resistant Dy-enriched film which decreases the anodic dissolution of Mg. Copyright © 2017 Elsevier B.V. All rights reserved.

Epitaxial growth and new phase of single crystal Dy by molecular beam epitaxy

International Nuclear Information System (INIS)

Yang, Kai-Yueh; Homma, Hitoshi; Schuller, I.K.

1987-09-01

We have grown two novel epitaxial phases of dysprosium (Dy) on vanadium (V) by molecular beam epitaxy technique. Surface and bulk structures are studied by in-situ reflection high energy electron diffraction (RHEED) and x-ray diffraction techniques. The new hcp phases are ∼4% expanded uniformly in-plane (0001), and ∼9% and ∼4% expanded out of plane along the c-axes for non-interrupted and interrupted deposition case, respectively. We also observed (2 x 2), (3 x 3), and (4 x 4) Dy surface reconstruction patterns and a series of transitions as the Dy film thickness increases. 12 refs., 3 figs

A study on dose attenuation in bone density when TBI using diode detector and TLD

International Nuclear Information System (INIS)

Im, Hyun Sil; Lee, Jung Jin; Jang, Ahn Ki; KIm, Wan Sun

2003-01-01

Uniform dose distribution of the whole body is essential factor for the total body irradiation(TBI). In order to achieved this goal, we used to compensation filter to compensate body contour irregularity and thickness differences. But we can not compensate components of body, namely lung or bone. The purpose of this study is evaluation of dose attenuation in bone tissue when TBI using diode detectors and TLD system. The object of this study were 5 patients who undergo TBI at our hospital. Dosimetry system were diode detectors and TLD system. Treatment method was bilateral and delivered 10 MV X-ray from linear accelerator. Measurement points were head, neck, pelvis, knees and ankles. TLD used two patients and diode detectors used three patients. Results are as followed. All measured dose value were normalized skin dose. TLD dosimetry : Measured skin dose of head, neck, pelvis, knees and ankles were 92.78±3.3, 104.34±2.3, 98.03±1.4, 99.9±2.53, 98.17±0.56 respectably. Measured mid-depth dose of pelvis, knees and ankles were 86±1.82, 93.24±2.53, 91.50±2.84 respectably. There were 6.67%-11.65% dose attenuation at mid-depth in pelvis, knees and ankles. Diode detector : Measured skin dose of head, neck, pelvis, knees and ankles were 95.23±1.18, 98.33±0.6, 93.5±1.5, 87.3±1.5, 86.90±1.16 respectably. There were 4.53%-12.6% dose attenuation at mid-depth in pelvis, knees and ankles. We concluded that dose measurement with TLD or diode detector was inevitable when TBI treatment. Considered dose attenuation in bone tissue, We must have adequately deduction of compensator thickness that body portion involved bone tissue.

Surface activation of dyed fabric for cellulase treatment.

Science.gov (United States)

Schimper, Christian B; Ibanescu, Constanta; Bechtold, Thomas

2011-10-01

Surface activation of fabric made from cellulose fibres, such as viscose, lyocell, modal fibres and cotton, can be achieved by printing of a concentrated NaOH-containing paste. From the concentration of reducing sugars formed in solution, an increase in intensity of the cellulase hydrolysis by a factor of six to eight was observed, which was mainly concentrated at the activated parts of the fabric surface. This method of local activation is of particular interest for modification of materials that have been dyed with special processes to attain an uneven distribution of dyestuff within the yarn cross-section, e.g., indigo ring-dyed denim yarn for jeans production. Fabrics made from regenerated cellulose fibres were used as model substrate to express the effects of surface activation on indigo-dyed material. Wash-down experiments on indigo-dyed denim demonstrated significant colour removal from the activated surface at low overall weight loss of 4-5%. The method is of relevance for a more eco-friendly processing of jeans in the garment industry. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

DyNi2Mn—magnetisation and Mössbauer spectroscopy

International Nuclear Information System (INIS)

Wang Jianli; Campbell, Stewart James; Kennedy, Shane Joseph; Dou Shixue; Wu Guangheng

2012-01-01

The physical properties of DyNi 2 Mn doped with 57 Fe have been investigated by X-ray diffraction, magnetisation (10–300 K) and 57 Fe Mössbauer spectroscopy measurements (5–300 K). DyNi 2 Mn( 57 Fe) crystallizes in the MgCu 2 -type cubic structure (Fd   −3m space group). The ordering temperature is found to be T C  = 99(2) K, much higher than those of DyNi 2 (∼22 K) and DyMn 2 (∼35 K). Analyses of isothermal M–H curves and the related Arrott plots confirm that the magnetic phase transition at T C is second order. The magnetic entropy change around T C is 4.0 J/kg K for a magnetic field change of 0 T to 5 T. The spectra above T C exhibit features consistent with quadrupolar effects while below T C the spectra exhibit magnetic hyperfine splitting. The Debye temperature for DyNi 2 Mn has been determined as θ D  = 200(20) K from a fit to the variable temperature isomer shift IS(T).

DyNi{sub 2}Mn-magnetisation and Moessbauer spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Wang Jianli; Campbell, Stewart James, E-mail: stewart.campbell@adfa.edu.au [University of New South Wales, School of Physical, Environmental and Mathematical Sciences (Australia); Kennedy, Shane Joseph [ANSTO, Bragg Institute (Australia); Dou Shixue [University of Wollongong, Institute for Superconductivity and Electronic Materials (Australia); Wu Guangheng [Chinese Academy of Science, Institute of Physics (China)

2012-03-15

The physical properties of DyNi{sub 2}Mn doped with {sup 57}Fe have been investigated by X-ray diffraction, magnetisation (10-300 K) and {sup 57}Fe Moessbauer spectroscopy measurements (5-300 K). DyNi{sub 2}Mn({sup 57}Fe) crystallizes in the MgCu{sub 2}-type cubic structure (Fd{sup }-3m space group). The ordering temperature is found to be T{sub C} = 99(2) K, much higher than those of DyNi{sub 2} ({approx}22 K) and DyMn{sub 2} ({approx}35 K). Analyses of isothermal M-H curves and the related Arrott plots confirm that the magnetic phase transition at T{sub C} is second order. The magnetic entropy change around T{sub C} is 4.0 J/kg K for a magnetic field change of 0 T to 5 T. The spectra above T{sub C} exhibit features consistent with quadrupolar effects while below T{sub C} the spectra exhibit magnetic hyperfine splitting. The Debye temperature for DyNi{sub 2}Mn has been determined as {theta}{sub D} = 200(20) K from a fit to the variable temperature isomer shift IS(T).

Radiological surveillance employed at industrial application in a nuclear research centre

International Nuclear Information System (INIS)

Sanches, M.P.; Sordi, G.M.; Sahyun, A.; Rodrigues, D.L.

1996-01-01

The monitoring and dosimetry systems used at Industrial Application and Engineering Service Department of the Instituto de Pesquisas Energeticas e Nucleares of the Brazilian Nuclear Energy Commission (GE-IPEN-CNEN/SP) are analyzed,in order to verify the compliance with the condition established by the dose system limitation and the basic radiation protection standards. The criteria about the use of individual dosimetry for persons that work in these facilities are established. In case of an external radiation dosimetry, by using film badge method, a level of 200μGy has been assigned, considering the detection significant threshold. For dose in air due to electromagnetic radiation, using TLD dosimetry of CaSO 4 :Dy a quarter year significant threshold is 101μGy. A symbiosis between the workplace monitoring and the individual monitoring became necessary for optimization purpose. (authors). 5 refs., 2 tabs., 1 fig

Optical and luminescence properties of Dy3+ doped sodium silicate glass

Science.gov (United States)

Srisittipokakun, N.; Kaewkhao, J.

2017-07-01

The aim of the present work is to study the optical and luminescence properties of Dy2O3 doped Na2O-BaO-Bi2O3-SiO2 glasses. The Dy3+ ion is chosen as dopant because it emits three visible bands, blue (470-485 nm; 4F9/2→6H15/2), yellow (570-580 nm; 4F9/2→6H13/2) and red (640-655 nm; 4F9/2→6H11/2) luminescence and finds its applications in the fields of laser, white LEDs, telecommunication technology and display devices. NaBaBiSiDy glasses with the compositions of (30-x)SiO2: 10Bi2O3: 30Na2O: 30BaO: xDy2O3 where x=0.0, 0.1, 0.5, 1.0, 1.5 and 2.0 mol% were prepared by melt-quenching technique and characterized by using density, optical absorption photoluminescence (PL) and decay rate measurements as function of different concentrations. The density (ρ), molar volume (VM) and refractive index obtained were found to increase with increase in the concentration of Dy2O3 in the glass matrix. The chromaticity coordinates were calculated from emission spectra and analyzed with CIE color diagram and appear in the white light region under ultraviolet excitation.

Dose measurements using thermoluminescent dosimeters and DoseCal software at two paediatric hospitals in Rio de Janeiro

International Nuclear Information System (INIS)

Mohamadain, K.E.M.; Azevedo, A.C.P.; Rosa, L.A.R. da; Guebel, M.R.N.; Boechat, M.C.B.

2003-01-01

A dosimetric survey in paediatric radiology is currently being carried out at the paediatric units of two large hospitals in Rio de Janeiro city: IPPMG (Instituto de Pediatria e Puericultura Martagao Gesteira, University Hospital of Federal University of Rio de Janeiro) and IFF (Instituto Fernandes Figueira, FIOCRUZ). Chest X-ray examination doses for AP, PA and LAT projections of paediatric patients have been obtained with thermoluminescent dosimeters (TLDs) and with use of a software package DoseCal. In IPPMG and IFF 100 patients have been evaluated with the use of the TLDs and another group of 100 patients with the DoseCal software. The aim of this work was to estimate the entrance skin dose (ESD) for frontal, back and lateral chest X-rays exposure of paediatric patients. For ESD evaluation, three different TL dosimeters have been used, namely LIF:Mg, Ti (TLD100), CaSO 4 :Dy and LiF:Mg, Cu, P (TLD100H). The age intervals considered were 0-1, 1-5, 5-10 and 10-15 years. The results obtained with all dosimeters are similar, and it is in good agreement with the DoseCal software, especially for AP and PA projections. However, some larger discrepancies are presented for the LAT projection

The evaluation of dose of TSEI with TLD and diode detector of the uterine cervix cancer

International Nuclear Information System (INIS)

Je, Young Wan; Na, Keyung Su; Yoon, Il Kyu; Park, Heung Deuk

2005-01-01

To evaluate radiation dose and accuracy with TLD and diode detector when treat total skin with electron beam. Using Stanford Technique, we treated patient with Mycosis Fungoides. 6 MeV electron beam of LINAC was used and the SSD was 300 cm. Also, acrylic speller(0.8 cm) was used. The patient position was 6 types and the gantry angle was 64, 90 and 116 degree. The patient's skin dose and the output were detected 5 to 6 times with TLD and diode. The deviations of dose detected with TLD from tumor dose were CA + 6%, thigh + 8%, umbilicus + 4%, calf - 8%, vertex - 74.4%, deep axillae - 10.2%, anus and testis - 87%, sole - 86% and nails shielded with 4 mm lead + 4%. The deviations of dose detected with diode were - 4.5% ∼ + 5% at the patient center and - 1.1% ∼ + 1% at the speller. The deviation of total skin dose was + 8% ∼ - 8% and that deviation was within the acceptable range(±10%). The boost dose was irradiated for the low dose areas(vertex, anus, sole). The electron beam output detected at the sootier was stable. It is thought that the deviation of dose at patient center detected with diode was induced by detection point and patient position.

Warm white light generation from single phase Sr3Y(PO4)3:Dy3+, Eu3+ phosphors with near ultraviolet excitation

International Nuclear Information System (INIS)

Huang, B.Y.; Feng, B.L.; Luo, L.; Han, C.L.; He, Y.T.; Qiu, Z.R.

2016-01-01

Highlights: • Novel single phase phosphors were synthesized in an ambient air atmosphere. • A direct band gap about 4.5 eV of the host is calculated for the first time. • It is suitable for near UV chip excitation. • It emits warm white light with better CIE and lower CCT over previous reports. • The thermal quenching is similar to that of YAG:0.06Ce 3+ commercial phosphor. - Abstract: Novel Sr 3 Y(PO 4 ) 3 :Dy 3+ , Eu 3+ (SYP:Dy 3+ , Eu 3+ ) phosphors were synthesized by a standard solid-state reaction under an ambient air atmosphere and their structural and optical properties were investigated. XRD and diffuse reflectance spectra (DRS) were used to explore structural properties. The former showed that single phase phosphors were obtained and that the rare earth ions entered into the cubic host by substituting the smaller Y 3+ ions and thereby enlarging the unit cell. The DRS indicated that the host has a direct bandgap of 4.5 eV. Under 393 nm excitation, a strong and stable warm white light emission with high color purity was achieved in SY 0.92 P:0.06Dy 3+ , 0.04Eu 3+ . The energy transfer from Dy 3+ to Eu 3+ ions was investigated and the related mechanism was discussed based on the optical spectra and emission decay curves. The thermal quenching of emission is similar to that of YAG:0.06Ce 3+ . The results show the single phase phosphor is potential in warm white LED.

Synthesis and thermoluminescence of new Li2SO4:Eu and Li2SO4:Dy phosphors exposed to beta radiation

International Nuclear Information System (INIS)

Garcia H, A. R.; Bustamante L, G. A.; Castro C, A. I.; Bernal H, R.; Cruz V, C.; Burruel I, S. E.; Castano M, V. M.

2015-10-01

Full text: Li 2 SO 4 is systematically studied for the very first concerning their dosimetric capabilities. Pellet- shaped Eu and Dy doped Li 2 SO 4 phosphors were synthesized by sintering. Some samples were exposed to beta particle irradiation in order to investigate their thermoluminescence (Tl) features. Glow curves were obtained for 80 mg mass samples, showing that both, Tl sensitivity as well as the temperature at which the Tl maximum is recorded, depends upon the sample dopant. The glow curves of Li 2 SO 4 :Eu exhibit two maxima, located at 433 and 573 K, when a 5 K/s heating rate was used, being the most intense emission that observed at 573 K. The integrated Tl increases as the radiation dose was increased in the 0.25 - 5 Gy range, with no shift of the Tl maxima being observed, meaning that first order kinetics processes are involved in the Tl emission. The normalized sensitivity recorded in ten consecutive irradiation-Tl readout cycles shows a good reusability with only 5 % variability. The integrated Tl fades as a function of the elapsed time between irradiation and the corresponding Tl readout of Eu and Dy doped Li 2 SO 4 phosphors is obtained. From the obtained results, we conclude that Li 2 SO 4 is a promising phosphor material to develop high performance Tl dosimeters, and a long term research work focused to understand and to improve their Tl features is absolutely justified. (Author)

Response of TLD-100"T"M microtubes to two RQR3 quality radiation beams

International Nuclear Information System (INIS)

Nunes, M.G.; Villani, D.; Almeida, S.B.; Vivolo, V.; Yoriyaz, H.; Louis, G.M.J.

2016-01-01

The present work compares the response of TLD-100"T"M microcubes to two RQR 3 diagnostic radiology reference quality radiation beams, defined by IEC-61267 norm, aiming to evaluate the detectability of TLD-100"T"M energy dependence reported in literature within the same reference quality radiation range. TLD-100"T"M microcubes reproducibility is assessed through the response of a second set of TLD-100"T"M microcubes, evaluated in a second thermoluminescence reader, to the RQR 3 diagnostic radiology reference quality radiation beam implemented at the Laboratorio de Calibracao de Instrumentos of IPEN, Sao Paulo, SP, Brazil. The dependence of TLD-100"T"M microcubes TL response was not detectable in these conditions and the reproducibility of the measurements is 90,2%. (author)

Phosphorescent and thermoluminescent properties of SrAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} phosphors prepared by solid state reaction method

Energy Technology Data Exchange (ETDEWEB)

Mothudi, B.M., E-mail: mothubm@unisa.ac.za [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa); Department of Physics, University of South Africa, P.O. Box 392, Pretoria, ZA 6031 (South Africa); Ntwaeaborwa, O.M. [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa); Kumar, A.; Sohn, K. [Department of Material Science and Metallurgical Engineering, Sunchon National University, Sunchon, Chonam 540-742 (Korea, Republic of); Swart, H.C. [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa)

2012-05-15

Long persistent SrAl{sub 2}O{sub 4}:Eu{sup 2+} phosphors co-doped with Dy{sup 3+} were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl{sub 2}O{sub 4} were observed in all the samples. The broad band emission spectra at 497 nm for SrAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} were observed and the emission is attributed to the 4f{sup 6}5d{sup 1} to 4f{sup 7} transition of Eu{sup 2+} ions. The samples annealed at 1100-1200 Degree-Sign C showed similar broad TL glow curves centered at 120 Degree-Sign C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy{sup 3+} ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.

A personnel TLD system with person identification

International Nuclear Information System (INIS)

Widell, C.O.

1974-01-01

The TLD system uses Li 2 B 4 O 7 :Mn, Si sintered tablets which are heated by hot nitrogen. The slide which holds the tablets is coded by a self adhesive polyester-aluminium tape. This tape is BCD coded in an ordinary tape punch. The information on the punched tape includes a ten digit social-security number and a two digit information on location and type of dosimetry. By this system dosimetric data is directly transfered into a central dose register for Sweden. All personnel doses are there stored on social-security numbers. (author)

Magnetooptic effects and Auger electron spectroscopy of two-layer NiFe-Dy and Fe-Dy films with nonuniform layers

International Nuclear Information System (INIS)

Ehdel'man, I.S.; Markov, V.V.; Khudyakov, A.E.; Ivantsov, R.D.; Bondarenko, G.V.; Ovchinnikov, S.G.; Kesler, V.G.; Parshin, A.S.; Ronzhin, I.P.

2001-01-01

Magneto-optical effects (magnetic circular dichroism and meridional Kerr effect) and element distribution with layer thickness in two-layer NiFe-Dy and Fe-Dy films, prepared by thermal sputtering of component in ultrahigh vacuum, are investigated. It is shown, that Dy in a two-layer film in the temperature range of 80-300 K makes constant contributions to both effects investigated which are approximately equal to the values of the effects observed in an isolated Dy film only at temperatures below the temperature T c of Dy transition into a ferromagnetic state (T c ∼ 100 K for the films under study). This behaviour of magneto-optical effects is assumed to be due to the influence of a NiFe layer spin system on magnetic state of a Dy layer, this influence is enhanced by the deep penetration of Ni and Fe ions into Dy layer as it follows from the data obtained using Auger electron spectroscopy [ru

Preparation and structural characterization of the thermoluminescent material CaSO{sub 4}: Dy; Preparacion y caracterizacion estructural del material termoluminiscente CaSO{sub 4}: Dy

Energy Technology Data Exchange (ETDEWEB)

Sanchez R, A.; Azorin, J. [UAM-I, 09340 Mexico D.F. (Mexico); Gonzalez M, P.R. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Rivera, T. [CICATA-IPN, Legaria 694, 11500 Mexico D.F. (Mexico)

2005-07-01

The grade of crystallinity of a material is important so that the one is presented the thermoluminescence phenomenon; for what is necessary to study those structural characteristic of a TL material and to correlate them with its TL response when being irradiated with ionizing radiation. The calcium sulfate activated with Dysprosium (CaSO{sub 4}: Dy) it is a material that has demonstrated its efficiency in the dosimetry of the ionizing radiation for the thermoluminescence method. In this work the structural characterization of this prepared material for the recrystallization method by means of the evaporation of the solvent and their relationship with their TL response is presented. The results showed that the best material to be used in thermoluminescent dosimetry presents a crystalline structure in orthorhombic phase and a particle size in the interval of 80 {mu}m to 200 {mu}m. (Author)

Size-dependent structure and magnetic properties of DyMnO{sub 3} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Cai, Xuan; Shi, Lei, E-mail: shil@ustc.edu.cn; Zhou, Shiming; Zhao, Jiyin; Guo, Yuqiao; Wang, Cailin [Hefei National Laboratory for Physical Sciences at the Microscale, University of Science and Technology of China, Hefei, Anhui 230026 (China)

2014-09-14

The structure and magnetic properties of orthorhombic DyMnO{sub 3} nanoparticles with different particle sizes are investigated in this paper. With decreasing particle size, all the lattice parameters a, b, and c gradually decrease, whereas the orthorhombic distortion increases. Magnetic measurements reveal that the antiferromagnetic interaction of Mn ions is weakened due to the decrease in Mn-O-Mn bond angle. Above a critical field H*, DyMnO{sub 3} undergoes a field-induced metamagnetic transition at 4 K, which is related to the spin reversal of Dy moments. The critical field H* increases monotonically with size reduction, indicating an enhancement of the antiferromagnetic interaction of Dy ions due to the decreased distance between rare earth ions. The magnetization at 4 K and 5 T, i.e., M(4 K, 5 T) shows a non-monotonic variation with particle size d, i.e., M(4 K, 5 T) initially increases with size reduction but decreases again for d < 68 nm. A modified core-shell model, in which the ferromagnetic ordering (Dy magnetic structure) and antiferromagnetic ordering (Mn magnetic structure) coexist in the core, is proposed to explain this behavior.

Optimization of the obtaining method of CaSO{sub 4}: Dy + Ptfe dosimeters; Optimizacion del metodo de obtencion de dosimetros de CaSO{sub 4}: Dy + PTFE

Energy Technology Data Exchange (ETDEWEB)

Galicia A, J.; Rioja Ch, J.; Torijano C, E.; Azorin N, J., E-mail: blink19871@hotmail.com [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Av. San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico D. F. (Mexico)

2012-10-15

This work contain the obtained results of studying the response when irradiating to different dose of X-rays, dosimeters of CaSO{sub 4}: Dy + Ptfe using different lapses of time in their preparation (a lot of selected dosimeters of an elaboration process of 3 days and another of an elaboration process of 2 hours). For the elaboration of the powdered material, the evaporation method was used; the irradiation were carried out in a lineal accelerator Elekta Synergy property of the National Medical Center, 20 de November. The similarities and differences are shown among the two dosimeters lots together with an analysis of the shine curves and of calibration selecting those that presented a better behaviour and a more rea liable response. (Author)

Application of Glow Curve Deconvolution Method to Evaluate Low Dose TLD LiF

International Nuclear Information System (INIS)

Kurnia, E; Oetami, H R; Mutiah

1996-01-01

Thermoluminescence Dosimeter (TLD), especially LiF:Mg, Ti material, is one of the most practical personal dosimeter in known to date. Dose measurement under 100 uGy using TLD reader is very difficult in high precision level. The software application is used to improve the precision of the TLD reader. The objectives of the research is to compare three Tl-glow curve analysis method irradiated in the range between 5 up to 250 uGy. The first method is manual analysis, dose information is obtained from the area under the glow curve between pre selected temperature limits, and background signal is estimated by a second readout following the first readout. The second method is deconvolution method, separating glow curve into four peaks mathematically and dose information is obtained from area of peak 5, and background signal is eliminated computationally. The third method is deconvolution method but the dose is represented by the sum of area of peak 3,4 and 5. The result shown that the sum of peak 3,4 and 5 method can improve reproducibility six times better than manual analysis for dose 20 uGy, the ability to reduce MMD until 10 uGy rather than 60 uGy with manual analysis or 20 uGy with peak 5 area method. In linearity, the sum of peak 3,4 and 5 method yields exactly linear dose response curve over the entire dose range

TLD Intercomparison in accelerators for radiotherapy in three Latin american countries; Intercomparacion TLD en aceleradores para radioterapia en tres paises latinoamericanos

Energy Technology Data Exchange (ETDEWEB)

Gaona, E.; Azorin N, J.; Perez, M.A.; Picon, C.; Castellanos, E.; Plazas, M.C.; Murcia, G.; Archundia, L. [Depto. El Hombre y su Ambiente. Universidad Autonoma Metropolitana, Calz. Del Hueso 1100, 04960 Mexico D.F. (Mexico)

1998-12-31

In Radiotherapy one of the objectives is to establish and to give follow up to quality assurance programs which make sure that the doses administered to the patients with cancer are a high probability of a success in external radiation. Likewise, one of the present preoccupations of the United Nations Agencies as well as the International Atomic Energy Agency and the Pan-American Health Organization is the optimal employment of the radiations in the treatment of cancer patients since the administered dose in Radiotherapy suffers considerable variations by the lack of quality assurance programs. The use of Electron linear accelerators requires a program of quality assurance that includes expert personnel, equipment and adequate facilities. The more used methodology for the dosimetry calibration and characterization of X-ray beams and high energy electrons for radiotherapy use is using a ionization chamber dosemeter calibrated in a regional secondary standardization laboratory. However, to establish and give follow up to the quality assurance programs it is necessary the dosimetric intercomparison through TLD. In this study it was designed plastic phantoms with TLD crystals and it was made its characterization to realize an absorbed dose analysis in the crystals exposed at X-ray beams 6 MV and high energy electrons 10 and 12 MeV to standardize the dosimetric procedures and proceeding to realize an International Pilot intercomparison of absorbed doses in TLD crystals in three Latin American countries: Mexico, Peru and Colombia with the participation of accelerators of five different institutions. The found results show that the majority of the measured doses with TLD in the different accelerators were in the 0.95-1.05 range though it had two cases outside of this range. The use of the phantoms with TLD crystals shows that they are of excellent aid to make analysis of the doses administered to the patients and an intercomparison of results to standardize procedures at

Analysis of the glow curve of SrB 4O 7:Dy compounds employing the GOT model

Science.gov (United States)

Ortega, F.; Molina, P.; Santiago, M.; Spano, F.; Lester, M.; Caselli, E.

2006-02-01

The glow curve of SrB 4O 7:Dy phosphors has been analysed with the general one trap model (GOT). To solve the differential equation describing the GOT model a novel algorithm has been employed, which reduces significantly the deconvolution time with respect to the time required by usual integration algorithms, such as the Runge-Kutta method.

Analysis of the glow curve of SrB4O7:Dy compounds employing the GOT model

International Nuclear Information System (INIS)

Ortega, F.; Molina, P.; Santiago, M.; Spano, F.; Lester, M.; Caselli, E.

2006-01-01

The glow curve of SrB 4 O 7 :Dy phosphors has been analysed with the general one trap model (GOT). To solve the differential equation describing the GOT model a novel algorithm has been employed, which reduces significantly the deconvolution time with respect to the time required by usual integration algorithms, such as the Runge-Kutta method

IAEA/WHO TLD postal dose audit service and high precision measurements for radiotherapy level dosimetry

International Nuclear Information System (INIS)

Izewska, J.; Bera, P.; Vatnitsky, S.

2002-01-01

Since 1969 the International Atomic Energy Agency, together with the World Health Organization, has performed postal TLD audits to verify calibration of radiotherapy beams in developing countries. The TLD programme also monitors activities of Secondary Standard Dosimetry Laboratories (SSDLs). The programme has checked approximately 4000 clinical beams in over 1100 hospitals, and in many instances significant errors have been detected in the beam calibration. Subsequent follow-up actions help to resolve the discrepancies, thus preventing further mistreatment of patients. The audits for SSDLs check the implementation of the dosimetry protocol in order to assure proper dissemination of dosimetry standards to the end-users. The TLD audit results for SSDLs show good consistency in the basic dosimetry worldwide. New TLD procedures and equipment have recently been introduced by the IAEA that include a modified TLD calibration methodology and computerised tools for automation of dose calculation from TLD readings. (author)

Coercivity enhancement of Dy-free Nd–Fe–B sintered magnets by intergranular adding Ho{sub 63.4}Fe{sub 36.6} alloy

Energy Technology Data Exchange (ETDEWEB)

Liang, Liping; Ma, Tianyu, E-mail: maty@zju.edu.cn; Wu, Chen; Zhang, Pei; Liu, Xiaolian; Yan, Mi, E-mail: mse_yanmi@zju.edu.cn

2016-01-01

High coercivity Nd–Fe–B sintered magnets serving in high-temperature environments always consume expensive and scarce heavy rare-earth Dy, which has simulated considerable interest to reduce Dy usage. In this work, coercivity of Dy-free magnets was investigated through intergranular adding eutectic Ho{sub 63.4}Fe{sub 36.6} powders. The coercivity increases gradually up to 4 wt% Ho{sub 63.4}Fe{sub 36.6} addition, however the remanence starts to deteriorate drastically as the addition is over 2.5 wt%. Coercivity above 18.0 kOe is obtained at the expense of a slight reduction in remanence through optimizing the addition amount and sintering conditions. The coercivity enhancement is explained through microstructural observations and elemental distribution analysis. (i) (Nd, Ho){sub 2}Fe{sub 14}B shell forms in the outer region of 2:14:1 phase grains, strengthening the local magnetic anisotropy filed, (ii) RE-rich grain boundary phase with low Fe content is thickened, weakening the magnetic coupling between adjacent 2:14:1 phase grains, and (iii) 2:14:1 phase grains are refined upon lowering sintering temperature, reducing the microstructural defects and the stray fields aroused from neighboring grains. - Highlights: • Eutectic Ho{sub 63.4}Fe{sub 36.6} powders were intergranular added to NdFeB sintered magnets. • The doped Dy-free magnet possessed coercivity of 18.0 kOe, remanence of 13.15 kGs. • (Nd, Ho){sub 2}Fe{sub 14}B shell formed in the surface of the matrix grains, increasing the H{sub A}. • Thick grain boundaries with low Fe content formed, decoupling the matrix grains. • By sintered at lower temperature, the matrix phase grains were refined.

Evaluation of the exchange interaction and crystal fields in a prototype Dy2 SMM

Science.gov (United States)

Zhang, Qing; Sarachik, Myriam; Baker, Michael; Chen, Yizhang; Kent, Andrew; Pineda, Eufemio; McInnes, Eric

In order to gain an understanding of the INS and magnetization data obtained for Dy2, the simplest member of a newly synthesized family of dysprosium-based molecular magnets, we report on calculations of the magnetic behavior of a Dy2 cluster with the formula [hqH2][Dy2(hq)4(NO3)3].MeOH. The molecular complex contains one high symmetry Dy(III) ion and one low symmetry Dy(III) ion. Our calculations suggest that exchange coupling between the two ions controls the behavior of the magnetization at low temperature, while the crystal field of the low symmetry Dy(III) ion controls the behavior at higher temperature. A point charge electrostatic model, based on crystallographic coordinates, provides a starting point for the determination of the crystal field. Parameters in these calculations are adjusted to provide best fits to inelastic neutron scattering data (INS) and low temperature magnetometry: the INS measurements access crystal field energies and low temperature magnetization probes the Dy-Dy exchange interaction. Work supported by ARO W911NF-13-1-1025 (CCNY) and NSF-DMR-1309202 (NYU).

Ionizing radiation source detection by personal TLD

International Nuclear Information System (INIS)

Marinkovic, O.; Mirkov, Z.

2002-01-01

The Laboratory for personal dosimetry has about 3000 workers under control. The most of them work in medicine. Some institutions, as big health centers, have different ionizing radiation sources. It is usefull to analyze what has been the source of irradiation, special when appears a dosimeter with high dose. Personal dosimetry equipment is Harshaw TLD Reader Model 6600 and dosimeters consist of two chips LiF TLD-100 assembled in bar-coded cards which are wearing in holders with one tissue-equivalent filter (to determine H(10)) and skin-equivalent the other (to determine H(0.07)). The calibration dosimeters have been irradiated in holders by different sources: x-ray (for 80keV and 100keV), 6 0C o, 9 0S r (for different distances from beta source) and foton beem (at radiotherapy accelerator by 6MeV, 10MeV and 18MeV). The dose ratio for two LiF cristals was calculated and represented with graphs. So, it is possible to calculate the ratio H(10)/H(0.07) for a personal TLD and analyze what has been the source of irradiation. Also, there is the calibration for determination the time of irradiation, according to glow curve deconvolution

Enhanced ultraviolet photo-response in Dy doped ZnO thin film

Science.gov (United States)

Kumar, Pawan; Singh, Ranveer; Pandey, Praveen C.

2018-02-01

In the present work, a Dy doped ZnO thin film deposited by the spin coating method has been studied for its potential application in a ZnO based UV detector. The investigations on the structural property and surface morphology of the thin film ensure that the prepared samples are crystalline and exhibit a hexagonal crystal structure of ZnO. A small change in crystallite size has been observed due to Dy doping in ZnO. AFM analysis ascertains the grain growth and smooth surface of the thin films. The Dy doped ZnO thin film exhibits a significant enhancement in UV region absorption as compared to the pure ZnO thin film, which suggests that Dy doped ZnO can be used as a UV detector. Under UV irradiation of wavelength 325 nm, the photocurrent value of Dy doped ZnO is 105.54 μA at 4.5 V, which is 31 times greater than that of the un-doped ZnO thin film (3.39 μA). The calculated value of responsivity is found to increase significantly due to the incorporation of Dy in the ZnO lattice. The observed higher value of photocurrent and responsivity could be attributed to the substitution of Dy in the ZnO lattice, which enhances the conductivity, electron mobility, and defects in ZnO and benefits the UV sensing property.

Optical properties of Dy3+ doped yttrium aluminium borate

International Nuclear Information System (INIS)

Vazquez, R MartInez; Osellame, R; Marangoni, M; Ramponi, R; Dieguez, E; Ferrari, M; Mattarelli, M

2004-01-01

A Dy 3+ doped yttrium aluminium borate (Dy:YAB) crystal has been optically characterized. The refractive indices at seven different wavelengths, ranging from the visible to the near infrared (IR), have been measured and the Sellmeier curves have been calculated. The polarized optical absorption spectra have been obtained at room temperature, and the Judd-Ofelt parameters have been calculated. The lifetime of the upper laser level 4 F 9/2 has been estimated and compared with the experimental value. Evidence of high luminescence quantum efficiency of the 4 F 9/2 state in YAB is provided by measured lifetimes

NRC TLD Direct Radiation Monitoring Network

International Nuclear Information System (INIS)

Struckmeyer, R.; McNamara, N.

1991-12-01

This report provides the status and results of the NRC Thermoluminescent Dosimeter (TLD) Direct Radiation Monitoring Network. It presents the radiation levels measured in the vicinity of NRC licensed facilities throughout the country for the third quarter of 1991

Improvement of routes and production of CaSO4-based dosimeters with unusual doping

International Nuclear Information System (INIS)

Junot, Danilo Oliveira

2017-01-01

The widespread use of ionizing radiation in medicine and industry, associated with the known risks that this type of radiation can cause, has motivated the search for new radiation detectors, seeking improvements in the dosimetric characteristics and in the cost of production in comparison with commercial dosimeters disseminated. The motivation of this work is, therefore, to produce new thermoluminescent detectors through improved routes. Unusual elements in CaSO 4 matrix doping, such as terbium (Tb) and ytterbium (Yb), were used as dopants in this matrix, as well as the europium (Eu), the thulium (Tm) and the silver (Ag), resulting in samples of CaSO 4 :Eu,Tb, CaSO 4 :Tb,Yb, CaSO 4 :Tm,Ag and CaSO 4 :Eu,Ag that were prepared by means of an adaptation of the method developed by Yamashita (1971). The route of synthesis is based on the mixture of calcium carbonate (CaCO 3 ) and dopant oxide (except for silver, incorporated in the form of metallic nanoparticles) in a solution of sulfuric acid. The mixture is heated until all the acid evaporates and only the powder of the material remains. In this route, the sulfuric acid is collected and can be reused. The phosphors produced were characterized by X-ray diffraction and radioluminescence techniques. The silver particles, produced by the polyol method, were characterized by scanning electron microscopy. Composites were obtained from the addition of Teflon to the phosphors. The thermoluminescence (TL) and the optically stimulated luminescence (OSL) of the new materials produced were investigated. Thermoluminescent characteristics such as sensitivity, linearity, reproducibility, minimum detectable dose, kinetic order and fading were evaluated and discussed. The CaSO 4 :Tb,Eu composites showed TL glow curves with peaks at temperatures of 170 °C, 270 °C and 340 °C. The CaSO 4 :Tb,Yb composites presented TL glow curves with peaks at temperatures of 90 °C, 160 °C, 240 °C and 340 °C. CaSO 4 :Tm showed peaks at

Data processing of personnel exposure in TLD and film systems

International Nuclear Information System (INIS)

Lerner, A.; Liav, N.; Eisen, Y.

1979-01-01

The program for the processing and storage of data on the personnel irradiation exposure in Israel is built on the data base of the Weizmann Institute of Science; it is a general program suitable for both TLD and film dosimetry. The TSO system helped bring up-to-date the data of the various collections in an interactive way. The introduction of the TLD dosemeters in the badge service required certain changes in the thinking line - this because the TLD being a personal dosemeter is returned into service after having been deciphered. This demands following up the dosemeter when the worker moves from unit to unit or after he had finished his work. The program takes into account the internal exposures,too and conforms to the new recommendation published in ICRP-26. (B.G.)

Efficient photoluminescence of Dy3+ at low concentrations in nanocrystalline ZrO2

International Nuclear Information System (INIS)

Diaz-Torres, L.A.; Rosa, E. de la; Salas, P.; Romero, V.H.; Angeles-Chavez, C.

2008-01-01

Nanocrystalline ZrO 2 :Dy 3+ were prepared by sol-gel and the structural and photoluminescence properties characterized. The crystallite size ranges from 20 to 50 nm and the crystalline phase is a mixture of tetragonal and monoclinic structure controlled by dopant concentration. Strong white light produced by the host emission band centered at ∼460 nm and two strong Dy 3+ emission bands, blue (488 nm) and yellow (580 nm), under direct excitation at 350 nm were observed. The highest efficiency was obtained for 0.5 mol% of Dy 3+ . Emission is explained in terms of high asymmetry of the host suggesting that Dy 3+ are substituted mainly into Zr 4+ lattice sites at the crystallite surface. Luminescence quenching is explained in terms of cross-relaxation of intermediate Dy 3+ levels. - Graphical abstract: White light emission from ∼70 nm ZrO 2 :Dy 3+ nanocrystals. The highest efficiency was obtained for 0.5 mol% of dopant and the dominant crystalline structure was monoclinic

Peculiarity of component interaction in {l_brace}Y, Dy{r_brace}-Mn-Sn ternary systems

Energy Technology Data Exchange (ETDEWEB)

Romaka, V.V. [Department of Materials Engineering and Applied Physics, Lviv Polytechnic National University, Ustyyanovycha Str. 5, 79013 Lviv (Ukraine); Konyk, M. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Romaka, L., E-mail: romakal@franko.lviv.ua [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Pavlyuk, V. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Jan Dlugosz University, Institute of Chemistry, Environmental Protection and Biotechnology, al. Armii Krajowej 13/15, 42200 Czestochowa (Poland); Ehrenberg, H. [Institute for Complex Materials, IFW Dresden, Helmholtzstrasse 20, D-01069 Dresden (Germany); Tkachuk, A. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine)

2011-07-14

Highlights: > {l_brace}Y, Dy{r_brace}-Mn-Sn ternary systems at 770 K are characterized by formation of stannides with general compositions RMn{sub 6}Sn{sub 6} and R{sub 4}Mn{sub 4}Sn{sub 7}. > The crystal structure of YMn{sub 6}Sn{sub 6} was determined by single crystal and powder diffraction methods. > Structural analysis showed that Dy{sub 4}Mn{sub 4}Sn{sub 7} compound is disordered. > Isostructural R{sub 4}Mn{sub 4}Sn{sub 7} compounds were also found with Gd, Tb, Ho, Er, Tm(confirmed), Yb, and Lu. - Abstract: The phase equilibria in the Y-Mn-Sn and Dy-Mn-Sn ternary systems were studied at 770 K by means of X-ray and metallographic analyses in the whole concentration range. Both Y-Mn-Sn and Dy-Mn-Sn systems are characterized by formation of two ternary compounds RMn{sub 6}Sn{sub 6} (MgFe{sub 6}Ge{sub 6}-type, space group P6/mmm) and R{sub 4}Mn{sub 4}Sn{sub 7} (Zr{sub 4}Co{sub 4}Ge{sub 7}-type, space group I4/mmm). The disorder in Dy{sub 4}Mn{sub 4}Sn{sub 7} compound was found by single crystal method. Compounds with the same type of structure were also found with Gd, Tb, Ho, Er, Tm (confirmed), Yb, and Lu and their lattice parameters were determined.

Down-shifting by energy transfer in Tb{sup 3+}/Dy{sup 3+} co-doped zinc phosphate glasses

Energy Technology Data Exchange (ETDEWEB)

Caldiño, U., E-mail: cald@xanum.uam.mx [Departamento de Física, Universidad Autónoma Metropolitana-Iztapalapa, P.O. Box 55-534, México, D.F. 09340 (Mexico); Muñoz H, G.; Camarillo, I. [Departamento de Física, Universidad Autónoma Metropolitana-Iztapalapa, P.O. Box 55-534, México, D.F. 09340 (Mexico); Speghini, A. [Dipartimento di Biotecnologie, Università di Verona, and INSTM, UdR Verona, Strada Le Grazie 15, I-37314 Verona (Italy); IFAC CNR, Nello Carrara Institute of Applied Physics, MDF Lab, I-50019 Sesto Fiorentino, FI (Italy); Bettinelli, M. [Dipartimento di Biotecnologie, Università di Verona, and INSTM, UdR Verona, Strada Le Grazie 15, I-37314 Verona (Italy)

2015-05-15

An optical spectroscopy investigation of zinc phosphate glasses activated with Tb{sup 3+}/Dy{sup 3+} ions is carried out through photoluminescence spectra and decay time measurements. The emission color can be adjusted from yellow–green light, with CIE1931 chromaticity coordinates (0.36,0.44), toward the white light region (0.35,0.39) by decreasing the Tb{sup 3+} content from 1.0 to 0.1 mol% of Tb(PO{sub 3}){sub 3} upon Dy{sup 3+} excitation at 423 nm. Such visible region luminescence is generated by {sup 5}D{sub 4}→{sup 7}F{sub 5} and {sup 5}D{sub 4}→{sup 7}F{sub 3} emissions of Tb{sup 3+} in addition to {sup 4}I{sub 15/2}→{sup 6}H{sub 15/2}, {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2}, {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} and {sup 4}F{sub 9/2}→{sup 6}H{sub 11/2} emissions of Dy{sup 3+}, so that Tb{sup 3+} emission is sensitized by Dy{sup 3+} through a non-radiative resonant energy transfer. A dominant {sup 5}D{sub 4}→{sup 7}F{sub 5} green emission is observed in detriment of the {sup 5}D{sub 3}→{sup 7}F{sub J} blue emissions upon 282 nm excitation, as well as an extended excitation range (280–500 nm), due to multiple Dy{sup 3+} and Tb{sup 3+} transitions, which might contribute to enhance the spectral response of solar photovoltaic cells by down-shifting of the incident solar spectrum. - Highlights: • Zn(PO{sub 3}){sub 2} glasses are optically activated with Tb{sup 3+}/Dy{sup 3+} (ZPTbDy). • Non-radiative resonant energy transfer takes place between Tb{sup 3+} and Dy{sup 3+}. • Luminescence can be adjusted from yellow–green light toward the white light region. • ZPTbDy phosphor exhibits spectroscopic properties for photovoltaic applications.

Development of BaSO4:Eu thermoluminescence phosphor

International Nuclear Information System (INIS)

Madhusoodanan, U.; Jose, M.T.; Lakshmanan, A.R.

1999-01-01

A highly sensitive thermoluminescence (TL) phosphor based on BaSO 4 :Eu was developed following the coprecipitation technique and firing in argon atmosphere at 1123 K. Photoluminescence studies confirm that firing in argon atmosphere instead of air increased the incorporation of Eu ions in 2+ valence state. At low γ-ray doses, its TL sensitivity is nearly 2 to 3 times higher than that of CaSO 4 :Dy phosphor. The other salient features of this BaSO 4 :Eu TL phosphor are a constant glow curve shape and a nearly linear γ-ray dose response

A method to minimise the fading effects of LiF:Mg,Ti (TLD-600 and TLD-700) using a pre-heat technique.

Science.gov (United States)

Lee, YoungJu; Won, Yuho; Kang, Kidoo

2015-04-01

Passive integrating dosemeters [thermoluminescent dosimeter (TLD) and optically stimulated luminescence (OSL)] are the only legally permitted individual dosemeters for occupational external radiation exposure monitoring in Korea. Also its maximum issuing cycle does not exceed 3 months, and the Korean regulations require personal dosemeters for official assessment of external radiation exposure to be issued by an approved or rather an accredited dosimetry service according to ISO/IEC 17025. KHNP (Korea Hydro & Nuclear Power, LTD), a unique operating company of nuclear power plants (NPPs) in Korea, currently has a plan to extend a TLD issuing cycle from 1 to 3 months under the authors' fading error criteria, ±10%. The authors have performed a feasibility study that minimises post-irradiation fading effects within their maximum reading cycle employing pre-heating technique. They repeatedly performed irradiation/reading a bare TLD chip to determine optimum pre-heating conditions by analysing each glow curve. The optimum reading conditions within the maximum reading cycle of 3 months were decided: a pre-heating temperature of 165°C, a pre-heating time of 9 s, a heating rate of 25°C s(-1), a reading temperature of 300°C and an acquisition time of 10 s. The fading result of TLD-600 and TLD-700 carried by newly developed time temperature profile (TTP) showed a much smaller fading effect than that of current TTP. The result showed that the fading error due to a developed TTP resulted in a ∼5% signal loss, whereas a current TTP caused a ∼15% loss. The authors also carried out a legal performance test on newly developed TTP to confirm its possibility as an official dosemeter. The legal performance tests that applied the developed TTP satisfied the criteria for all the test categories. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Comparison of laboratory and in situ evaluation of environmental TL dosimeters

International Nuclear Information System (INIS)

Deme, S.; Apathy, I.; Feher, I.; Osvay, M.

1996-01-01

The passive environmental gamma-radiation dosimetry is mainly based on TL (thermoluminescent) dosimetry. This method offers considerable advantages due to its high precision, low cost, wide range, etc.. At the same time its application involves uncertainty caused by the dose collected during the transport from the point of annealing to the place of exposure and back to the place of evaluation. Should an accident occur read-out is delayed due to the need to transport to a laboratory equipped with a TLD reader. A portable reader capable of reading out the TL dosimeter at the place of exposure (in situ TLD reader) eliminates the disadvantages mentioned above. A microprocessor based portable TLD reader was developed by us for monitoring environmental gamma-radiation doses. Using a portable reader for in situ evaluation there are several disadvantages as well. The method requires the transport of the reader instead of dosimeters. The portable reader should be battery operated with low power consumption. Due to this requirement the temperature stabilization of the reader requests different solution as in laboratory type devices. Comparison of recently developed in situ and traditional laboratory evaluation methods of environmental TL dosimeters is given in recent paper. The comparison was made in the same conditions. The most characteristic - for environmental monitoring - numerical TL data (dose range, reproducibility, fading, self dose etc.) are given for manufactured by us CaSO 4 :Dy bulbs (portable reader) and very advantageous, high sensitive Al 2 O 3 :C dosimeters (laboratory evaluation). (author)

Neutron area monitor with TLD pairs

International Nuclear Information System (INIS)

Guzman G, K. A.; Borja H, C. G.; Valero L, C.; Hernandez D, V. M.; Vega C, H. R.

2011-11-01

The response of a passive neutron area monitor with pairs of thermoluminescent dosimeters has been calculated using the Monte Carlo code MCNP5. The response was calculated for one TLD 600 located at the center of a polyethylene cylinder, as moderator. When neutrons collide with the moderator lose their energy reaching the TLD with thermal energies where the ambient dose equivalent is calculated. The response was calculated for 47 monoenergetic neutron sources ranging from 1E(-9) to 20 MeV. Response was calculated using two irradiation geometries, one with an upper source and another with a lateral source. For both irradiation schemes the response was calculated with the TLDs in two positions, one parallel to the source and another perpendicular to the source. The advantage of this passive neutron monitor area is that can be used in locations with intense, pulsed and mixed radiation fields. (Author)

Centralized TLD service and record keeping in Canada

International Nuclear Information System (INIS)

Grogan, D.; Ashmore, J.P.; Bradley, R.P.

1979-01-01

A centralized automated TLD service operated by the Department of National Health and Welfare went into operation in May 1977 to monitor radiation workers throughout Canada. Twenty-thousand employees from a wide range of disciplines are enrolled and the number will be increased to fifty thousand by September l978. A prototype of the system, operational from September 1976 to May 1977 for three-thousand people, has already been described. A description of technical and operational highlights is presented as well as a description of problems experienced during the first full year of operation. Details of costs, conversion logistics, operational performance and technical problems are included. A comparison of the advantages and disadvantages of changing from film dosimetry to TLD in a nationwide context is detailed. The dose meter read-out unit is interfaced, through video terminals, with a time-sharing computer system programmed to provide direct access to the Canadian National Dose Registry. Details of this linkage are described, as are the computer programmes for routine processing of raw batch data. The centralized TLD service interactively linked with the National Dose Registry provides a comprehensive occupational monitoring programme invaluable for regulatory control. (author)

An environmental TLD for nuclear power plants

International Nuclear Information System (INIS)

Marcinowski, F.

1988-01-01

In this paper a dosimeter is proposed for the purpose of detecting noble gas releases (principally Xe-133) from nuclear power plants. The dosimeter consists of two Li 2 B 4 O 7 :Cu (LiBO) elements and one CaSO 4 :Tm (CaSO) element. One LiBO element is enclosed only in plastic and is used to determine shallow dose, while the LiBO and CaSO pair, which are used to determine deep dose, are enclosed in a 1070 mg/cm 2 aluminum sphere and plastic. The dosimeter is designed to overcome the three major problems involved in monitoring for Xe-133: the effect of angular response, differences in irradiation geometry (overhead plume vs. submersion), and interference from naturally occurring high-energy gamma rays. Laboratory test data are presented to demonstrate the proposed dosimeter's response characteristics

Magnetic hyperfine fields in Dy/sub 1-x/Y/sub x/Al2

International Nuclear Information System (INIS)

Hessel, A.; Kalvius, G.M.; Shenoy, G.K.; Zinn, W.; Wiedemann, W.

1982-01-01

161 Dy Moessbauer spectroscopy was carried out at 4.2 K on Dy/sub 1-x/Y/sub x/Al 2 for 0 less than or equal to x less than or equal to 0.6. For x=0 we find B=580 T and f/sub Q/=2810 MHz, close to free-ion values. For x > 0 both B and f/sub Q/ decrease weakly. We obtain (δB)/sub n/ = -14 T, (δf/sub Q/)/sub n/ = -110 MHz and (δB)/sub nn/ = + 1.6 T, (δf/sub Q/)/sub nn/ = +4 MHz per replaced nearest and next-nearest Dy 3 + neighbor, respectively

Neutron-scattering study of the magnetic structure of DyFe₄Al₈ and HoFe₄Al₈

DEFF Research Database (Denmark)

Paixao, J.A.; Silva, M.R.; Sørensen, S.Aa.

2000-01-01

The magnetic structures of DyFe4Al8 and HoFe4Al8, which have been reported to be unusual spin-glass systems, were studied in detail by neutron diffraction, using both unpolarized and polarized beams. In fact these compounds have long-range magnetic order in both the Fe and rare-earth sublattices....

Remote system for measurement of radon alpha emitter for population safety guards

International Nuclear Information System (INIS)

Jesus, Vasquez; Sajo-Bohus, Laszlo; Palacios, Daniel; Barros, Haydn

2013-01-01

The objective of this research project is to study the OSL properties for high doses of dosemeters traditionally applied in thermoluminescent dosimetry (TL), as CaF2: Dy (TLD 200) and CaF2: Mn (TLD 400), and thus verify the applicability of OSL technique in high-dose dosimetry

Remote system for measurement of radon alpha emitter for population safety guards; Sistema remoto de medicion de radon alfa emisor para la salvaguarda poblacional-3599

Energy Technology Data Exchange (ETDEWEB)

Jesus, Vasquez, E-mail: jesus.vasguez@lnl.infn.it [Istituto Nazionale di Fisica Nucleare, Legnaro (Italy). Laboratorio Nazionale di Legnaro; Sajo-Bohus, Laszlo; Palacios, Daniel; Barros, Haydn, E-mail: sajobohus@gmail.com, E-mail: sanjuro.perdomo@gmail.com, E-mail: lab.nuclear@gmail.com [Universidad Simon Bolivar (USB), Caracas (Venezuela, Bolivarian Republic of). Laboratorio de Fisica Nuclear

2013-07-01

The objective of this research project is to study the OSL properties for high doses of dosemeters traditionally applied in thermoluminescent dosimetry (TL), as CaF2: Dy (TLD 200) and CaF2: Mn (TLD 400), and thus verify the applicability of OSL technique in high-dose dosimetry.

Evaluation of the thermoluminescent detector answers of CaSO4:Dy, LiF:Mg,Ti and micro LiF:Mg,Ti in photon clinical beams dosimetry using water simulator

International Nuclear Information System (INIS)

Matsushima, Luciana C.; Veneziani, Glauco R.; Campos, Leticia L.

2011-01-01

This paper perform the comparative study of thermoluminescent answer of calcium sulfate dosemeter doped with dysprosium (DaSO 4 :Dy) produced by the IPEN, Sao Paulo, with answer of lithium fluoride dosemeters doped with magnesium and titanium (LiF:Mg, Ti) in the dosimetry of clinical beams of photons (6 and 15 MV) by using water simulator object. Dose-answer curves were obtained for gamma radiation of cobalt-60 in the air and in conditions of electronic equilibrium (plate of PMMA), and clinical photons of CLINAC model 2100C accelerators of the two evaluated hospitals: Hospital das Clinicas of the Faculty of Medicine of Sao Paulo university and Hospital Albert Einstein. It was also evaluated the sensitivity and reproduction of the three dosemeters

Rhombus-shaped tetranuclear [Ln4] complexes [Ln = Dy(III) and Ho(III)]: synthesis, structure, and SMM behavior.

Science.gov (United States)

Chandrasekhar, Vadapalli; Hossain, Sakiat; Das, Sourav; Biswas, Sourav; Sutter, Jean-Pascal

2013-06-03

The reaction of a new hexadentate Schiff base hydrazide ligand (LH3) with rare earth(III) chloride salts in the presence of triethylamine as the base afforded two planar tetranuclear neutral complexes: [{(LH)2Dy4}(μ2-O)4](H2O)8·2CH3OH·8H2O (1) and [{(LH)2Ho4}(μ2-O)4](H2O)8·6CH3OH·4H2O (2). These neutral complexes possess a structure in which all of the lanthanide ions and the donor atoms of the ligand remain in a perfect plane. Each doubly deprotonated ligand holds two Ln(III) ions in its two distinct chelating coordination pockets to form [LH(Ln)2](4+) units. Two such units are connected by four [μ2-O](2-) ligands to form a planar tetranuclear assembly with an Ln(III)4 core that possesses a rhombus-shaped structure. Detailed static and dynamic magnetic analysis of 1 and 2 revealed single-molecule magnet (SMM) behavior for complex 1. A peculiar feature of the χM" versus temperature curve is that two peaks that are frequency-dependent are revealed, indicating the occurrence of two relaxation processes that lead to two energy barriers (16.8 and 54.2 K) and time constants (τ0 = 1.4 × 10(-6) s, τ0 = 7.2 × 10(-7) s). This was related to the presence of two distinct geometrical sites for Dy(III) in complex 1.

Investigation of natural radiation background and assessment of its population dose in China

International Nuclear Information System (INIS)

1989-01-01

This paper presents the nationwide survey in 1984-1988 of environmental external radiation by integrating measurements, and the assessment of population doses from obtained data. Thermoluminescent dosimeters (TLD) model ETLD-80 with CaSO 4 : Dy were used. The survey was conducted in two different scales. In general survey, TLDs were distributed in whole area of every investigated provinces; and in local survey, one city and one village within each province were selected and investigated for the purpose of comparison of the natural radiation levels between the rural and urban areas. A marked characteristics was noted that the level of natural environmental radiation in south China seems to be higher than that in north China. It may be attributed to the geological difference in both parts. The annual individual average and collective effective dose equivalents to population of China from natural environmental radiation were estimated to be 780 μSv and 8.1 x 10 5 man. Sv, based on the model recommended by UNSCEAR 1988 Report

NRC TLD Direct Radiation Monitoring Network. Progress report, January-June 1981

International Nuclear Information System (INIS)

1982-04-01

This report provides the status and results of the NRC Thermoluminescent Dosimeter (TLD) Direct Radiation Monitoring Network. It presents the radiation levels measured in the vicinity of 55 NRC-licensed facility sites throughout the country for the first half of 1981. The program objectives, scope, and methodology are given. The TLD system, dosimeter location, data processing scheme, and quality assurance program are outlined

Dy{sup 3+} ions as optical probes for studying structure of boro-tellurite glasses

Energy Technology Data Exchange (ETDEWEB)

Tuyen, Vu Phi, E-mail: vptuyen@gust-edu.vast.vn [Duytan University, K7/25 Quang Trung, Da Nang (Viet Nam); Graduate University of Science and Technology – VAST, 18 Hoang Quoc Viet, Hanoi (Viet Nam); Sengthong, Bounyavong; Quang, Vu Xuan [Duytan University, K7/25 Quang Trung, Da Nang (Viet Nam); Van Do, Phan [Thuyloi University, 175 Tay Son, Dong Da, Hanoi (Viet Nam); Van Tuyen, Ho; Xuan Hung, Le [Duytan University, K7/25 Quang Trung, Da Nang (Viet Nam); Thanh, Nguyen Trong [Institute of Materials Science – VAST, 18 Hoang Quoc Viet, Hanoi (Viet Nam); Nogami, Masayuki [Duytan University, K7/25 Quang Trung, Da Nang (Viet Nam); Toyota Physical and Chemical research Institute (Japan); Hayakawa, Tomokatsu [Nagoya Institute of Technology, Gokisocho Showaku, 466-8555 Nagoya, Aichiken (Japan); Huy, Bui The, E-mail: buithehuy.nt@gmail.com [Duytan University, K7/25 Quang Trung, Da Nang (Viet Nam); Department of Chemistry, Changwon National University, Changwon 641-773 (Korea, Republic of)

2016-10-15

Dy{sup 3+}-doped glasses with various compositions (35+x)B{sub 2}O{sub 3}+ (45−x)TeO{sub 2}+9.5ZnO+10Na{sub 2}O+0.5Dy{sub 2}O{sub 3} (x=0; 10 and 20) were prepared by a melt–quenching technique. The Dy{sup 3+} ions are used as an optical probe, of which the Judd–Ofelt parameters, the phonon-side band, and the Raman spectra were quantitatively estimated to search the change of glass structure (the change of the ratio of [BO{sub 4}] to [BO{sub 3}] units, formation of the non-bridging oxygens (NBO{sup −}), the change of [TeO{sub 3}] to [TeO{sub 4}] units) as a function of the B{sub 2}O{sub 3} content. The Ω{sub 2} and Ω{sub 6} values of Dy{sup 3+}-doped boro-tellurite samples are larger than that of Dy{sup 3+}-doped borate or tellurite sample. The CIE chromaticity color coordinates were calculated for the luminescence spectra of Dy{sup 3+} ions of the glasses with the different compositions and they were all located in the vicinity of white light center of the color coordination diagram.

Asteroids Dynamic Site-AstDyS

Science.gov (United States)

Knezevic, Zoran; Milani, Andrea

2012-08-01

The AstDyS online information service (http://hamilton.dm.unipi.it/astdys/) contains data on numbered and multi - opposition asteroids, including orbital elements, their uncertainty, proper elements, ephemerides with uncertainty, and more. AstDyS also provides additional scientific output computed from the raw observational data. This value added currently includes: more accurate orbits computed with advanced dynamical and observational error model s; their uncertainty, as expressed by the covariance matrix formalism; ephemerides computed on request for each observer, with uncertainty; mean and proper orbital elements (for this output, AstDyS is the primary source worldwide); statistical quality control, providing a rigorous observational error model. All this is available with a sophisticated web interface, providing multiple search functions and online computations as well as complete orbital and residual files. There are several ways in which the A stDyS service could be expanded and improved in the next future, like the explicit classification of asteroids into asteroid families, the classification of resonant asteroids, and an updated self - consistent population model (to be used, e.g., for survey simulations). The IAU Division I endorsed the proposal for AstDyS to become an IAU (permanent) service, which would include the IAU supervision of the AstDyS system, keeping under control the quality of the work and the continuous update under conditions of scientific competition.

The Ras antagonist, farnesylthiosalicylic acid (FTS, decreases fibrosis and improves muscle strength in dy/dy mouse model of muscular dystrophy.

Directory of Open Access Journals (Sweden)

Yoram Nevo

Full Text Available The Ras superfamily of guanosine-triphosphate (GTP-binding proteins regulates a diverse spectrum of intracellular processes involved in inflammation and fibrosis. Farnesythiosalicylic acid (FTS is a unique and potent Ras inhibitor which decreased inflammation and fibrosis in experimentally induced liver cirrhosis and ameliorated inflammatory processes in systemic lupus erythematosus, neuritis and nephritis animal models. FTS effect on Ras expression and activity, muscle strength and fibrosis was evaluated in the dy(2J/dy(2J mouse model of merosin deficient congenital muscular dystrophy. The dy(2J/dy(2J mice had significantly increased RAS expression and activity compared with the wild type mice. FTS treatment significantly decreased RAS expression and activity. In addition, phosphorylation of ERK, a Ras downstream protein, was significantly decreased following FTS treatment in the dy(2J/dy(2J mice. Clinically, FTS treated mice showed significant improvement in hind limb muscle strength measured by electronic grip strength meter. Significant reduction of fibrosis was demonstrated in the treated group by quantitative Sirius Red staining and lower muscle collagen content. FTS effect was associated with significantly inhibition of both MMP-2 and MMP-9 activities. We conclude that active RAS inhibition by FTS was associated with attenuated fibrosis and improved muscle strength in the dy(2J/dy(2J mouse model of congenital muscular dystrophy.

Development of BaSO sub 4 :Eu thermoluminescence phosphor

CERN Document Server

Madhusoodanan, U; Lakshmanan, A R

1999-01-01

A highly sensitive thermoluminescence (TL) phosphor based on BaSO sub 4 :Eu was developed following the coprecipitation technique and firing in argon atmosphere at 1123 K. Photoluminescence studies confirm that firing in argon atmosphere instead of air increased the incorporation of Eu ions in 2+ valence state. At low gamma-ray doses, its TL sensitivity is nearly 2 to 3 times higher than that of CaSO sub 4 :Dy phosphor. The other salient features of this BaSO sub 4 :Eu TL phosphor are a constant glow curve shape and a nearly linear gamma-ray dose response.

Measurement of man's exposure to external radiation

International Nuclear Information System (INIS)

Becker, K.

1975-01-01

After outlining briefly the rationale for personnel radiation monitoring with integrating detectors, a review is presented of some developments which have taken place in personnel and environmental dosimetry during the past 3.5 years. The results of a pilot field experiment concerning the stability of film and thermoluminescent dosimeters (TLDs) in four Latin-American countries are summarized. It shows that film dosimeters should be used only with caution, and in locations with a moderate climate. A survey is being conducted on the current status and trends in personnel monitoring, involving detailed questioning of over 150 laboratories in about forty countries to obtain information on the type of service and detectors, evaluation and recordkeeping, additional applications, problem and development areas, intercomparisons, practical experiences with different systems, administrative and legal aspects, etc. According to the preliminary results, the trend is away from photographic film and towards mostly automatic TLD systems, not only in the industrialized countries but also in several of the larger and more advanced developing countries. The need for higher quality standards and frequent performance tests under realistic conditions is emphasized. Differences in the requirements for personnel and []stationary environmental dosimeters are outlined. As evidenced by the results of a recent international intercomparison of such dosimeters under laboratory and field conditions, involving 56 dosimeter sets from eleven countries, reasonably accurate results can be obtained with several TLD systems including LiF, CaSO 4 :Dy, and CaF 2 :Mn; however CaF 2 :Dy is less reliable than the others and film is not adequate at all. Transit doses were found to be erratic and frequently high. Limitations in the assessment of population doses from stationary detector readings are discussed. (auth)

Anisotropic magnetic properties of Dy{sub 6}Cr{sub 4}Al{sub 43} single crystal

Energy Technology Data Exchange (ETDEWEB)

Maurya, Arvind, E-mail: arvindmaurya@tifr.res.in; Thamizhavel, A., E-mail: arvindmaurya@tifr.res.in; Dhar, S. K., E-mail: arvindmaurya@tifr.res.in [Department of Condensed Matter Physics and Material Science, Tata Institute of Fundamental Research, Mumbai-400005 (India)

2014-04-24

We have studied the anisotropic magnetic behavior of the rare earth intermetallic compound Dy{sub 6}Cr{sub 4}Al{sub 43}. This compound crystallizes in the hexagonal symmetry and orders ferromagnetically at 8.3 K as confirmed by the magnetic susceptibility and heat capacity measurements. A significant anisotropy in the magnetization is observed between the c axis and the ab-plane. The easy axis liesin theab-plane at low temperatures; however it orients itselfalong the c-axis above 170 K as inferred from the susceptibility data.

SU-E-I-09: Application of LiF:Mg,Cu (TLD-100H) Dosimeters for in Diagnostic Radiology

Energy Technology Data Exchange (ETDEWEB)

Sina, S [Radiation Research Center, Shiraz University, Shiraz (Iran, Islamic Republic of); Zeinali, B; Karimipourfard, M; Lotfalizadeh, F; Sadeghi, M [Nuclear Engineering Department, Shiraz University, Shiraz (Iran, Islamic Republic of); Faghihi, R [Radiation Research Center, Shiraz University, Shiraz (Iran, Islamic Republic of); Nuclear Engineering Department, Shiraz University, Shiraz (Iran, Islamic Republic of)

2014-06-01

Purpose: Accurate dosimetery is very essential in diagnostic radiology. The goal of this study is to verify the application of LiF:Mg,Cu,P (TLD100H) in obtaining the Entrance skin dose (ESD) of patients undergoing diagnostic radiology. The results of dosimetry performed by TLD-100H, were compared with those obtained by TLD100, which is a common dosimeter in diagnostic radiology. Methods: In this study the ESD values were measured using two types of Thermoluminescence dosimeters (TLD-100, and TLD-100H) for 16 patients undergoing diagnostic radiology (lumbar spine imaging). The ESD values were also obtained by putting the two types of TLDs at the surface of Rando phantom for different imaging techniques and different views (AP, and lateral). The TLD chips were annealed with a standard procedure, and the ECC values for each TLD was obtained by exposing the chips to equal amount of radiation. Each time three TLD chips were covered by thin dark plastic covers, and were put at the surface of the phantom or the patient. The average reading of the three chips was used for obtaining the dose. Results: The results show a close agreement between the dose measuered by the two dosimeters.According to the results of this study, the TLD-100H dosimeters have higher sensitivities (i.e.signal(nc)/dose) than TLD-100.The ESD values varied between 2.71 mGy and 26.29 mGy with the average of 11.89 mGy for TLD-100, and between 2.55 mGy and 27.41 mGy with the average of 12.32 mGy for measurements. Conclusion: The TLD-100H dosimeters are suggested as effective dosimeters for dosimetry in low dose fields because of their higher sensitivities.

SU-E-I-09: Application of LiF:Mg,Cu (TLD-100H) Dosimeters for in Diagnostic Radiology

International Nuclear Information System (INIS)

Sina, S; Zeinali, B; Karimipourfard, M; Lotfalizadeh, F; Sadeghi, M; Faghihi, R

2014-01-01

Purpose: Accurate dosimetery is very essential in diagnostic radiology. The goal of this study is to verify the application of LiF:Mg,Cu,P (TLD100H) in obtaining the Entrance skin dose (ESD) of patients undergoing diagnostic radiology. The results of dosimetry performed by TLD-100H, were compared with those obtained by TLD100, which is a common dosimeter in diagnostic radiology. Methods: In this study the ESD values were measured using two types of Thermoluminescence dosimeters (TLD-100, and TLD-100H) for 16 patients undergoing diagnostic radiology (lumbar spine imaging). The ESD values were also obtained by putting the two types of TLDs at the surface of Rando phantom for different imaging techniques and different views (AP, and lateral). The TLD chips were annealed with a standard procedure, and the ECC values for each TLD was obtained by exposing the chips to equal amount of radiation. Each time three TLD chips were covered by thin dark plastic covers, and were put at the surface of the phantom or the patient. The average reading of the three chips was used for obtaining the dose. Results: The results show a close agreement between the dose measuered by the two dosimeters.According to the results of this study, the TLD-100H dosimeters have higher sensitivities (i.e.signal(nc)/dose) than TLD-100.The ESD values varied between 2.71 mGy and 26.29 mGy with the average of 11.89 mGy for TLD-100, and between 2.55 mGy and 27.41 mGy with the average of 12.32 mGy for measurements. Conclusion: The TLD-100H dosimeters are suggested as effective dosimeters for dosimetry in low dose fields because of their higher sensitivities

White light generation from Dy3+-doped yttrium aluminium gallium mixed garnet nano-powders

International Nuclear Information System (INIS)

Praveena, R.; Balasubrahmanyam, K.; Jyothi, L.; Venkataiah, G.; Basavapoornima, Ch.; Jayasankar, C.K.

2016-01-01

Yttrium aluminium gallium garnet (here after referred as YAGG), Y 3 Al 5−y Ga y O 12 (where y=1.0, 2.5 and 4.0), nano-powders doped with 1.0 mol% of dysprosium (Dy 3+ ) ions were synthesised by the citrate sol–gel method. The structure, phase evolution, morphology and luminescence properties of these nano-crytalline powders were characterized by means of XRD, FTIR, Raman, electron microscopy and UV–vis spectroscopy. From the XRD results, the crystallite sizes were found to be in the range of 18–26 nm. Excitation spectra of YAGG nano-powders showed that the samples can be efficiently excited by near UV and blue LEDs. Upon excitation at 448 nm, the emission spectra of all these samples showed two bands centred at 485 (blue) and 585 nm (yellow) which corresponds to the 4 F 9/2 → 6 H 15/2 and 4 F 9/2 → 6 H 13/2 transitions of Dy 3+ ion, respectively. Intensity of blue emission was found to be stronger than the yellow emission in all the three samples. Integrated yellow to blue (Y/B) emission intensity was found to be increased with increasing the Ga content in the present YAGG host. Therefore, concentration (0.1, 1.0, 2.0 and 4.0 mol%) of Dy 3+ ions was varied in the Ga rich (Y 3 Ga 4 AlO 12 ) nano-powder. The chromaticity co-ordinates of all the prepared nano-powders were located in the white light region and also found to be dependent on Dy 3+ ion concentration and excitation wavelength. The decay curves for 4 F 9/2 level of Dy 3+ ion exhibited non-exponential nature in all the studied samples and the lifetime values remained constant (~1.0 ms) with increasing the Ga content, but were found to decrease with increasing the Dy 3+ ion concentration. The results indicated that 2.0 mol% of Dy 3+ -doped Y 3 Ga 4 AlO 12 nano-powder under 352 nm excitation is suitable for the white light emitting device applications.

Influence of Precursor Composition on the Microstructure and Superconducting Properties of Dy-Ba-Cu-O filaments

International Nuclear Information System (INIS)

Ikebe, Y; Ban, E; Matsuoka, Y; Nishijima, G; Watanabe, K

2006-01-01

Dy-Ba-Cu-O filaments have been successfully fabricated by a solution spinning method. The relationship between the partial melting temperature and the transport J c value at 77 K of the filamentary sample was systematically investigated. Two kinds of precursor filaments with starting composition of Dy:Ba:Cu = 1.18:2.12:3.09 (sample A)and Dy:Ba:Cu = 1.00:2.00:3.00 (sample B) were partially melted in 1%O 2 + Ar atmospheric gas and oxygenated in pure 100% O 2 gas. Samples partially melted at a wide temperature range of 990-1040 deg. C had J c values higher than 10 4 A/cm 2 . Both sample A and sample B partially melted at 1020 deg. C exhibited the maximum J c value higher than 4.2 x 10 4 A/cm 2 and 2.0 x 10 4 A/cm 2 , respectively. These samples had a dense microstructure consisting predominantly of Dy123 and finely dispersed Dy211 particles. The Dy211 particles with a diameter of about 1μm were finely dispersed in sample A, while the particles with a diameter of about 5μm were observed in sample B. The J c values of both samples were maintained about 2.0 x 10 3 A/cm 2 up to 14 T

Evaluation of TLD dose response compared to MCNP-5 simulation of diagnostic X ray equipment - radiation diagnostic image

International Nuclear Information System (INIS)

Sanchez G, R.; Cavalieri, T. A.; De Paiva, F.; Dalledone S, P. de T.; Yoriyaz, H.; Rodrigues F, M. A.; Vivolo, V.

2014-08-01

The thermo luminescent dosimeter (TLD) is used as a radiation dosimeter and can be used as environmental and staff personnel monitoring. The TLD measures ionizing radiation exposure by a process in which the amount of radiation collected by the dosimeter is converted in visible light when the crystal is heated. The amount of emitted light is proportional to the radiation exposure, and then the response of the TLD must be the related to the real dose. In this work it was used twenty four TLD 700 in order to obtain eight values of doses from a diagnostic X-ray equipment. The TLD-700 is a LiF TLD enriched with 7 Li isotope. One way to compare and study the response of TLD is by Monte Carlo method, which has been used as a computational tool to solve problems stochastically. This method can be applied to any geometry, even those where the boundary conditions are unknown, making the method particularly useful to solve problems a priori. In this work it was modeled the X-ray tube exactly as the one used to irradiate the TLD, after the simulation and the TLD irradiation the results of dose value from both were compared. (Author)

Evaluation of TLD dose response compared to MCNP-5 simulation of diagnostic X ray equipment - radiation diagnostic image

Energy Technology Data Exchange (ETDEWEB)

Sanchez G, R.; Cavalieri, T. A.; De Paiva, F.; Dalledone S, P. de T.; Yoriyaz, H. [Instituto de Pesquisas Energeticas e Nucleares, Centro de Engenharia Nuclear / CNEN, Av. Lineu Prestes 2242, Cidade Universitaria, 05508-000 Sao Paulo (Brazil); Rodrigues F, M. A. [Universidade Estadual Paulista, Faculdade de Medicina de Botucatu, Departamento de Dermatologia e Radioterapia, Av. Prof. Montenegro s/n, Rubiao Junior, 18601-970 Botucatu (Brazil); Vivolo, V., E-mail: chancez@hotmail.com [Instituto de Pesquisas Energeticas e Nucleares, Gerencia de Metrologia das Radiacoes / CNEN, Av. Lineu Prestes 2242, Cidade Universitaria, 05508-000 Sao Paulo (Brazil)

2014-08-15

The thermo luminescent dosimeter (TLD) is used as a radiation dosimeter and can be used as environmental and staff personnel monitoring. The TLD measures ionizing radiation exposure by a process in which the amount of radiation collected by the dosimeter is converted in visible light when the crystal is heated. The amount of emitted light is proportional to the radiation exposure, and then the response of the TLD must be the related to the real dose. In this work it was used twenty four TLD 700 in order to obtain eight values of doses from a diagnostic X-ray equipment. The TLD-700 is a LiF TLD enriched with {sup 7}Li isotope. One way to compare and study the response of TLD is by Monte Carlo method, which has been used as a computational tool to solve problems stochastically. This method can be applied to any geometry, even those where the boundary conditions are unknown, making the method particularly useful to solve problems a priori. In this work it was modeled the X-ray tube exactly as the one used to irradiate the TLD, after the simulation and the TLD irradiation the results of dose value from both were compared. (Author)

Tuning the luminescence color and enhancement of afterglow properties of Sr(4−x−y)CaxBayAl14O25:Eu2+,Dy3+ phosphor by adjusting the composition

International Nuclear Information System (INIS)

Luitel, Hom Nath; Watari, Takanori; Chand, Rumi; Torikai, Toshio; Yada, Mitsunori; Mizukami, Hiroshi

2013-01-01

Graphical abstract: Excitation and fluorescence emission spectra of three extreme compositions of Ca, Sr and Ba in Sr 4 Al 14 O 25 phosphor (viz. 4CaO·7Al 2 O 3 , 4SrO·7Al 2 O 3 and 4BaO·7Al 2 O 3 ) doped with 4 at% Eu 2+ and 8 at% Dy 3+ (inset shows the digital micrograph of corresponding phosphors). -- Highlights: • Bright phosphor, Sr (4−x−y) Ca x Ba y Al 14 O 25 :Eu 2+ ,Dy 3+ , was synthesized by adjusting the composition. • The solid solubility of Ca and Ba in the Sr 4 Al 14 O 25 host was determined to be 20 and 10 mol%, respectively. • Substituting part of Sr by Ca, the emission color can be well tuned from blue to green. • A white afterglow was observed when 3.2 mol of Sr was substituted by Ca. • The afterglow luminescence was enhanced by 1.5 times by 0.2 mol Ca substitution. -- Abstract: Color point tuning is an important challenge for improving the practical applications of various displays, especially there are very limited white color single hosts that emits in the white spectrum. In this paper, the possibility of color tuning by substituting part of host lattice cation (Sr 2+ ions) by Ca 2+ or Ba 2+ ions in an efficient strontium aluminate phosphor, Sr 4 Al 14 O 25 :Eu 2+ ,Dy 3+ , is reported and found to be very promising for displays. A detail study by replacing part of Sr 2+ with Ca 2+ or Ba 2+ has been investigated. X-ray diffraction study showed that crystal structure of Sr 4 Al 14 O 25 is preserved up to 20 mol of Ca 2+ ion exchange while it is limited to 10 mol of Ba 2+ ions exchange. Substantial shift in the emission band and color were observed by substitution of Sr 2+ by Ca 2+ or Ba 2+ ions. A bluish-white emission and afterglow was observed at higher Ca 2+ ions substitution. Further, partial Ca 2+ substitutions (up to 0.8 mol) resulted in enhanced afterglow of Sr 4 Al 14 O 25 :Eu 2+ ,Dy 3+ phosphor. However, Ba 2+ substitution decreased the fluorescence as well afterglow of the Sr 4 Al 14 O 25 :Eu 2+ ,Dy 3+ phosphor

Determination of Antimicrobial Activity of the Dyed Silk Fabrics with Some Natural Dyes

OpenAIRE

ALKAN, Rezan; TORGAN, Emine; AYDIN, Canan; KARADAG, Recep

2015-01-01

In this study, silk fabric is dyed with natural indigo. Dyed silk fabric with natural indigo was cut in the 20x20 cm2 size. Excluding a fabric, all fabrics were mordanted in the same percentage with alum metal (KAl(SO4)2.12H2O). Then, silk fabrics for green color dyeing are dyed separately with weld (Reseda luteola), gall oak (Quercus infectoria Olivier) and together weld (Reseda luteola) and gall oak (Quercus infectoria) in different percentage. Antimicrobial functionality of the twenty seve...

Periodicity of TLD badge personnel monitoring service in India

International Nuclear Information System (INIS)

Kher, R.K.; Joshi, V.D.; Kaushik, Aruna; Sharma, Amiy; Chatterjee, S.

2003-01-01

The periodicity of an individual monitoring service is an important aspect. Presently minimum period for TLD badge service is maintained as 'calendar month' and choice of quarterly service is also offered. The periodicity of the TLD service for a given category/application type of institution, is to be fixed taking into account level of average occupational doses in all or typical institutions of given category and other information indicating the status of safety and possible fluctuations of exposure levels and potential for overexposure cases. This paper presents the status on the periodicity of TLD Badge Service as is evolved and adopted for the four broad categories i.e. DAE (Nuclear Fuel Cycle) Institutions, Industrial, Medical, Research institutions. It is concluded that quarterly service is a convenient option for institution categories where type of work/workload, and work practices are such that occupational exposures could be normally kept below about one mSv or so in the monitoring period, average annual dose less than 1 mSv and persons receiving annual dose >10 mSv is less than 1% of total in the category. Also, the judicious use of the flexibility in the periodicity of TLD Badge service would help (i) to keep the monitoring related workload to the optimum for the monitoring units and (ii) to keep the expenses incurred by the institution towards monitoring to the minimum without sacrificing radiation safety (iii) to focus the extra monitoring efforts on the applications/situations requiring improvement in radiation safety. (author)

Dysprosium doping induced shape and magnetic anisotropy of Fe{sub 3−x}Dy{sub x}O{sub 4} (x=0.01–0.1) nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Jain, Richa [School of Sciences, Indira Gandhi National Open University, Maidan Garhi, New Delhi 110068 (India); Department of Physics, ARSD college, University of Delhi, New Delhi 110021 (India); Luthra, Vandna [Department of Physics, Gargi College, Siri Fort Road, New Delhi 110049 (India); Gokhale, Shubha, E-mail: sgokhale@ignou.ac.in [School of Sciences, Indira Gandhi National Open University, Maidan Garhi, New Delhi 110068 (India)

2016-09-15

The effect of dysprosium doping on evolution of structural and magnetic properties of magnetite (Fe{sub 3}O{sub 4}) nanoparticles is reported. A standard route of co-precipitation was used for the synthesis of undoped and doped magnetite nanoparticles Fe{sub 3−x}Dy{sub x}O{sub 4} (x=0.0–0.1). Transmission electron microscopy (TEM) shows formation of round shaped particles with diameter in the range of 8–14 nm for undoped sample. On doping beyond x=0.01, the formation of rod like structures is initiated along with the round shaped particles. The number of rods is found to increase with increasing doping concentration. Magnetic characterization using Vibrating Sample Magnetometer (VSM) revealed doping dependent magnetic properties which can be correlated with the crystallite size as determined from X-ray diffraction (XRD). Enhancement in the saturation magnetization in the initial stages of doping can be explained on the basis of incorporation of Dy{sup 3+} ions in the inverse spinel structure at the octahedral site in place of Fe{sup 3+} ions. Subsequent decrease in saturation magnetization observed beyond x=0.03 could be attributed to precipitation of excess Dy in form of dysprosium ferrite phase. - Highlights: • Report on formation of nanorods in magnetite prompted by Dy doping. • Observation of anisotropic magnetic behaviour emanating from the shape anisotropy. • Evidence of Dy{sup 3+} ions occupying octahedral site in place of Fe{sup 3+} ions. • Nanorods envisaged to be useful as catalysts and in biomedical applications.

Photoluminescence and phosphorescence properties of MAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} (M=Ca, Ba, Sr) phosphors prepared at an initiating combustion temperature of 500 deg. C

Energy Technology Data Exchange (ETDEWEB)

Mothudi, B.M., E-mail: mothudibm@qwa.uovs.ac.z [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa); Ntwaeaborwa, O.M. [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa); Botha, J.R. [Department of Physics, Nelson Mandela Metropolitan University, Port Elizabeth, ZA 6031 (South Africa); Swart, H.C., E-mail: swarthc.sci@ufs.ac.z [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa)

2009-12-01

Eu{sup 2+} and Dy{sup 3+} co-doped calcium aluminate, barium aluminate and strontium aluminate phosphors were synthesized at an initiating combustion temperature of 500 deg. C using urea as an organic fuel. The crystallinity of the phosphors was investigated by using X-ray diffraction (XRD) and the morphology was determined by a scanning electron microscope (SEM). The low temperature monoclinic structure for both CaAl{sub 2}O{sub 4} and SrAl{sub 2}O{sub 4} and the hexagonal structure of BaAl{sub 2}O{sub 4} were observed. The effect of the host materials on the photoluminescence (PL) and phosphorescence properties were investigated by using a He-Cd Laser and a Cary Eclipse fluorescence spectrophotometer, respectively. The broad band emission spectra observed at 449 nm for CaAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+}, 450 nm (with a shoulder-peak at 500 nm) for BaAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} and 528 nm for SrAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} are attributed to the 4f{sup 6}5d{sup 1} to 4f{sup 7} transition in the Eu{sup 2+} ion in the different hosts.

Comparison of LiF (TLD-100 and TLD-100H) detectors for extremity monitoring

Energy Technology Data Exchange (ETDEWEB)

Freire, L. [Departamento de Proteccao Radiologica e Seguranca Nuclear, Instituto Tecnologico e Nuclear, E.N. 10, 2683-953 Sacavem (Portugal); Laboratorio de Medicina Nuclear, Lda, Atomedical, Rua Helena Felix, 11D, 1600-121 Lisboa (Portugal); Calado, A.; Cardoso, J.V.; Santos, L.M. [Departamento de Proteccao Radiologica e Seguranca Nuclear, Instituto Tecnologico e Nuclear, E.N. 10, 2683-953 Sacavem (Portugal); Alves, J.G. [Departamento de Proteccao Radiologica e Seguranca Nuclear, Instituto Tecnologico e Nuclear, E.N. 10, 2683-953 Sacavem (Portugal)], E-mail: jgalves@itn.pt

2008-02-15

In this work the results aimed at assessing the performance of two types of LiF detectors, TLD-100 and TLD-100H, used in the context of extremity dosimetry are presented. Each detector variety was studied for reproducibility, batch homogeneity, residual dose, linearity and energy dependence using, when appropriate, the {sup 90}Sr/{sup 90}Y radiation source built-in one of the Harshaw 6600 readers, the ISO narrow X-ray beams of N30, N40, N60, N80, N100 and N120 or the gamma radiations of {sup 137}Cs and {sup 60}Co. Two calibration energies (N120 and {sup 137}Cs) were also used. The reproducibility and linearity results indicate that both LiF:Mg,Ti and LiF:Mg,Cu,P performed equally well. However, LiF:Mg,Cu,P presents a higher residual signal. In terms of energy dependence, LiF:Mg,Cu,P shows less variation than LiF:Mg,Ti particularly when N120 is used as calibration radiation. This seems to be a more realistic setup since the energy of the most frequently used radioisotopes in Nuclear Medicine departments with single photon emission computed tomography (SPECT) use gamma radiation energies closer to N120 than to {sup 137}Cs.

Tailoring of magnetic properties of ultrathin epitaxial Fe films by Dy doping

Directory of Open Access Journals (Sweden)

A. A. Baker

2015-07-01

Full Text Available We report on the controlled modification of relaxation parameters and magnetic moments of epitaxial Fe thin films through Dy doping. Ferromagnetic resonance measurements show that an increase of Dy doping from 0.1% to 5% gives a tripling in Gilbert damping, and more importantly a strongly enhanced anisotropic damping that can be qualitatively understood through the slow-relaxing impurity model. X-ray magnetic circular dichroism measurements show a pronounced suppression of the orbital moment of the Fe with Dy doping, leading to an almost threefold drop in the orbital to spin moment ratio, ml/ms. Doping with Dy can therefore be used to control both dynamic and static properties of thin ferromagnetic films for improved performance in spintronics device applications, mediated through the antiferromagnetic interaction of the 4f and 3d states.

Tailoring of magnetic properties of ultrathin epitaxial Fe films by Dy doping

Energy Technology Data Exchange (ETDEWEB)

Baker, A. A. [Department of Physics, Clarendon Laboratory, University of Oxford, Oxford, OX1 3PU (United Kingdom); Magnetic Spectroscopy Group, Diamond Light Source, Didcot, OX11 0DE (United Kingdom); Figueroa, A. I.; Laan, G. van der [Magnetic Spectroscopy Group, Diamond Light Source, Didcot, OX11 0DE (United Kingdom); Hesjedal, T. [Department of Physics, Clarendon Laboratory, University of Oxford, Oxford, OX1 3PU (United Kingdom)

2015-07-15

We report on the controlled modification of relaxation parameters and magnetic moments of epitaxial Fe thin films through Dy doping. Ferromagnetic resonance measurements show that an increase of Dy doping from 0.1% to 5% gives a tripling in Gilbert damping, and more importantly a strongly enhanced anisotropic damping that can be qualitatively understood through the slow-relaxing impurity model. X-ray magnetic circular dichroism measurements show a pronounced suppression of the orbital moment of the Fe with Dy doping, leading to an almost threefold drop in the orbital to spin moment ratio, m{sub l}/m{sub s}. Doping with Dy can therefore be used to control both dynamic and static properties of thin ferromagnetic films for improved performance in spintronics device applications, mediated through the antiferromagnetic interaction of the 4f and 3d states.

Traceability of a panoramic gamma irradiator using different TLD systems as transfer instruments

International Nuclear Information System (INIS)

Romero, A.M.; Saez, J.C.

1994-01-01

This work shows the calibration in terms of the new operational radiological quantities Hp(10) and H*(10) for different TLD systems (Harshaw TLD-100 and Panasonic UD-802) used in personal and environmental monitoring. The irradiations were performed in the Spanish Reference Laboratory in radiation protection levels, managed by the CIEMAT Metrology of ionizing radiations Unit. With these data, different calibrations of a panoramic gamma irradiator in terms of the radiological quantity for unit of time were established, providing the traceability of the irradiator to the Reference Laboratory using the corresponding TLD systems as transfer instruments. (Author) 9 refs

Traceability of a panoramic gamma irradiator using different TLD systems as transfer Instruments

International Nuclear Information System (INIS)

Romero, A. M.; Saez, J. C

1994-01-01

This work shows the calibration in terms of the new operational radiological quantities Hp (10) and H(10) for different TLD systems (Harshaw TLD-100 and Panasonic UD-002) used in personal and environmental monitoring. The irradiations were performed in the Spanish Reference Laboratory in radiation protection levels, managed by the CIEMAT Metrology of ionizing radiations Unit. With those data, different calibrations of a panoramic gamma irradiator in terms of the radiological quantity for unit of time were established, providing the traceability of the irradiator to the Reference Laboratory using the corresponding TLD systems as transfer instruments. (Author) 9 refs

Postal TLD audits in radiotherapy in the Czech Republic: current status, experience and potential

International Nuclear Information System (INIS)

Ekendahl, Daniela; Kapucianova, Michaela; Dufek, Vladimir

2014-01-01

The paper deals with practice and performance of postal TLD audits in radiotherapy with emphasis on the possibilities of application of the advanced versions that were developed following up technological progress in radiotherapy. The new methodologies of the TLD audit are focused specifically on up-to-date linear accelerators, equipped with multileaf collimators, and modern treatment planning systems. The dose is checked by the TLD not only for reference conditions but also in conditions of radiation fields influenced by presence of inhomogeneities in the irradiated volume. As regards small radiation fields, the check also includes dose profile verification using gafchromic films. The methodologies were tested within pilot studies performed in collaboration with some Czech radiotherapy centers. The results and experience gave evidence of the usefulness and appropriateness of the new TLD audit methodologies. (orig.)

Optical absorption, luminescence, and energy transfer processes studies for Dy3+/Tb3+-codoped borate glasses for solid-state lighting applications

Science.gov (United States)

Lakshminarayana, G.; Kaky, Kawa M.; Baki, S. O.; Lira, A.; Caldiño, U.; Kityk, I. V.; Mahdi, M. A.

2017-10-01

By using melt quenching technique, good optical quality singly doped Dy3+ or Tb3+ and Dy3+/Tb3+-codoped borate glasses were synthesized and studied by optical absorption, excitation, emission and decay lifetimes curve analysis. Following the absorption spectrum, the evaluated Judd-Ofelt (J-O) intensity parameters (Ωλ (λ = 2, 4 and 6)) were used to calculate the transition probability (AR), the branching ratio (βR), and the radiative lifetime (τR) for different luminescent transitions such as 4I15/2 → 6H15/2, 4F9/2 → 6H15/2, 4F9/2 → 6H13/2, 4F9/2 → 6H11/2 and 4F9/2 → 6H9/2,6F11/2 for the 0.5 mol % singly Dy3+-doped glass. The βR calculated (65%) indicates that for lasing applications, 4F9/2 → 6H13/2 emission transition is highly suitable. For all the Dy3+/Tb3+-codoped glasses, Tb3+: 5D3→7F6 emission decay lifetime curves are found to be non-exponential in nature for different concentrations of Dy3+ codoping. Using the Inokuti-Hirayama model, these nonexponential decay curves were analyzed to identify the nature of the energy transfer (ET) processes and here the electric dipole-dipole interaction is dominant for the ET. Based on the excitation and emission spectra and decay lifetimes curve analysis, the cross relaxation and ET processes between Dy3+ and Tb3+ were confirmed. For the 0.5 mol % Tb3+ and 2.0 mol % Dy3+-codoped glass, the evaluated Tb3+→Dy3+ ET efficiency (η) is found to be 45% under 369 nm excitation. Further, for Tb3+/Dy3+ -codoped glasses, an enhancement of Tb3+ green emission is observed up to 1.5 mol % Dy3+ codoping, and this is due to the non-radiative resonant ET from Dy3+ to Tb3+ upon 395 nm excitation. For singly 0.5 mol % Dy3+ or 0.5 mol % Tb3+-doped glass, the calculated color coordinates (x,y) and correlated color temperatures (CCT) represent the neutral white or warm white light regions, whereas Dy3+/Tb3+-codoped glasses (x,y) and CCT values fall in the yellowish green region with respect to the different Dy3

Magnetostrictive effects in ferromagnetic Dy break-junctions

Energy Technology Data Exchange (ETDEWEB)

Mueller, Marc; Suergers, Christoph; Montbrun, Richard [Karlsruher Institut fuer Technologie, Physikalisches Institut, 76131 Karlsruhe (Germany); Loehneysen, Hilbert v. [Karlsruher Institut fuer Technologie, Physikalisches Institut, 76131 Karlsruhe (Germany); Karlsruher Institut fuer Technologie, Institut fuer Festkoerperphysik, 76021 Karlsruhe (Germany)

2011-07-01

A characteristic property of the rare-earth metals are their large magnetostrictive strains which are related to the magnetocrystalline anisotropy through the elastic energy. We have investigated the electrical conductance G of mechanical break-junctions of a dysprosium wire at 4.2 K where Dy is in the ferromagnetic state. In zero magnetic field we find the usual variation of the conductance G vs. electrode distance x while breaking the wire mechanically, with a sequence of steps and more or less prominent plateaus. The behavior G(x) is modified in magnetic fields {mu}{sub 0} H up to 1 T due to the large magnetostriction of Dy. In addition, the conductance can be changed reproducibly by variation of H. For a number of contacts we observe discrete changes in G(H) in the range of several G{sub 0} = 2 e{sup 2}/h. The behavior of G(H) and its angular dependence can be quantitatively understood by taking into account the magnetostrictive properties of Dy. This first realization of a magnetostrictive atomic switch demonstrates the possibility of reproducibly tuning the conductance of magnetic nanocontacts by a magnetic field.

Environmental dosimetry system based on LiF : Mg, Ti (TLD-100)

International Nuclear Information System (INIS)

Saez Vergara, J.C.

1990-01-01

The report presents the various tests carried out to the characterize a thermoluminescence environmental dosimetry systems, using the phosphor LiF:mg,Ti (TLD-100) in chip form. The holder has been specifically designed in order to obtain simplicity in the operation and to assure correct measurements in terms of the new operational quantities in radiation protection (ICRU-1985). Some topics in TLD Environmental Monitoring are discussed (Dark Current, Reference Light, Zero Reading, Free-in-Air or Phantom Calibration, Fading Correction, Transit Dose, etc.), and the proposed solutions are exposed. The tests performed have been designed to conform with the different existing international Standards and Recommendations (ANSI : N545-1975; IEC: Draft 45B-1987, ISO : DP 8034-19849. The data from an European Interlaboratory Programm (EUR-8932) have been used to evaluate the performance : the TLD System presented is among the best systems using TLD-100. The results obtained in the characterization (linearity, repeatability, detection threshold, residue, angular response, stability of stored information, etc.) show the optimum performance of this dosimetric system in its application to environmental gamma dose monitoring. Based on these results, two operational procedures have been developed for the application of this Dosimetric System, specially in Quality Assurance Monitoring Programs around Nuclear Plants in Spain. (author)

EFFECT OF ALKALINE IONS ON THE PHASE EVOLUTION, PHOTOLUMINESCENCE, AND AFTERGLOW PROPERTIES OF SrAl2O4: Eu2+, Dy3+ PHOSPHOR

Directory of Open Access Journals (Sweden)

HYUNHO SHIN

2012-12-01

Full Text Available A series of SrAl2O4: Eu2+, Dy3+ long-afterglow (LAG phosphors with varying concentration of Li+, Na+ and K+, has been synthesized. The increased concentration of the three types of alkaline ions does not decrease the quantity of the total luminescent phases (SrAl2O4 plus Sr4Al14O25, but a different set of secondary phases has been evoluted for the K+-added series due to the failure of the incorporation of relatively large K+ (1.38 Å to the Sr2+ (1.18 Å site in the hosts, unlike the cases of smaller Li+ (0.76 Å and Na+ (1.02 Å ions. PL excitation, PL emission, and LAG luminescence, are decreased by all investigated alkaline ions, which would be due to the diminished incorporation of Eu2+ and Dy3+ activators into the luminescent hosts by the alkaline ions. For the cases of the Li+ and Na+-added series, the incorporated Li+ or Na+ to the luminescent hosts would also limit the activation of Eu2+ and charge trapping/detrapping of Dy3+ to yield the diminished PL properties and LAG luminescence. The type of defect complex formed by the addition of Li+ and Na+ ions has been deduced and compared with that formed when no alkaline ion is added.

Faraday effect in γ-Dy2S3 and c-Dy2O3 paramagnetic crystals

International Nuclear Information System (INIS)

Shelykh, A.I.

1987-01-01

Studies of spectral and temperature dependences of Faraday effect in γ-Dy 2 S 3 and C-Dy 2 O 3 paramagnetic crystals are conducted. Paramagnetism of these crystals is brought about by Dy 3+ ions. Estimation of the effect of such factors as the value of paramagnetic ion concentration, width of the forbidden band, crystallochemical composition on magnetooptical effect in the considered compounds of dysprosium is carried out on the basis of the obtained experimental data and theoretical analysis. It is shown, that the Faraday effect in the considered compounds of dysprosium as well as the value of paramagnetic moment may be regarded rather accurately in free ion approximation

Deviations outside the acceptance limits in the IAEA/WHO TLD audits for radiotherapy hospitals

International Nuclear Information System (INIS)

Vatnitsky, S.; Izewska, J.

2002-01-01

The main purpose of the IAEA/WHO TLD postal dose audit programme for dosimetry in radiotherapy is to provide an independent verification of the dose delivered by treatment machines in radiotherapy hospitals. The results of the TLD audit are considered acceptable if the relative deviation between the participant's stated dose and the TLD determined dose is within ±5%. The goal of this note is to draw the attention of participants of the TLD programme to some of the common reasons for deviations outside the acceptance limits. Armed with this knowledge, other participants may avoid similar problems in the future. The analysis of deviations presented here is based on the results of TLD audits of the calibration of approximately 1000 Co-60 beams and 600 high-energy X-ray beams performed in the period 1996-2001. A total of 259 deviations outside the ±5% limits have been detected, including 204 deviations for Co-60 beams (20% of all Co-60 beams checked) and 55 for high-energy X-ray beams (10% of all X-ray beams checked). It is worth mentioning that the percentage of large deviations (beyond 10%) is also higher for Co-60 beams than for high-energy X-ray beams. Some problems may be caused by obsolete dosimetry equipment or poor treatment machine conditions. Other problems may be due to insufficient training of staff working in radiotherapy. The clinical relevance of severe TLD deviations detected in the audit programme was confirmed in many cases, but, fortunately, not all-poor dosimetric results reflect deficiencies in the calibration of clinical beams or machine faults. Sometime it happens, that the TLDs are irradiated with an incorrect dose due to misunderstanding of the instructions on how to perform the TLD irradiation. Such dosimetry errors would have no direct impact on actual dose delivered to a patient

Room-temperature ferromagnetism in Dy films doped with Ni

International Nuclear Information System (INIS)

Edelman, I.; Ovchinnikov, S.; Markov, V.; Kosyrev, N.; Seredkin, V.; Khudjakov, A.; Bondarenko, G.; Kesler, V.

2008-01-01

Temperature, magnetic field and spectral dependences of magneto-optical effects (MOEs) in bi-layer films Dy (1-x) Ni x -Ni and Dy (1-x) (NiFe) x -NiFe were investigated, x changes from 0 to 0.06. Peculiar behavior of the MOEs was revealed at temperatures essentially exceeding the Curie temperature of bulk Dy which is explained by the magnetic ordering of the Dy layer containing Ni under the action of two factors: Ni impurities distributed homogeneously over the whole Dy layer and atomic contact of this layer with continues Ni layer. The mechanism of the magnetic ordering is suggested to be associated with the change of the density of states of the alloy Dy (1-x) Ni x owing to hybridization with narrow peaks near the Fermi level character for Ni

DySectAPI: Scalable Prescriptive Debugging

DEFF Research Database (Denmark)

Jensen, Nicklas Bo; Karlsson, Sven; Quarfot Nielsen, Niklas

We present the DySectAPI, a tool that allow users to construct probe trees for automatic, event-driven debugging at scale. The traditional, interactive debugging model, whereby users manually step through and inspect their application, does not scale well even for current supercomputers. While...... lightweight debugging models scale well, they can currently only debug a subset of bug classes. DySectAPI fills the gap between these two approaches with a novel user-guided approach. Using both experimental results and analytical modeling we show how DySectAPI scales and can run with a low overhead...

Phase composition of iron-rich R-Fe-Si (R=Dy, Ho, Er) alloys

International Nuclear Information System (INIS)

Ivanova, G.V.; Makarova, G.M.; Shcherbakova, E.V.; Belozerov, E.V.

2005-01-01

Phase composition is studied in iron-rich alloys of R-Fe-Si (R=Dy, Ho, Er). In the as-cast state R 2 (Fe, Si) 17 of type Th 2 Ni 17 and R(Fe, Si) 12 compounds are observed; in the alloys of rated composition of R(Fe 0.85 Si 0.15 ) 8.5 (R=Dy, Er) a compound R 2 (Fe, Si) 17 of Th 2 Zn 17 -type is revealed as well. The annealing at 1273 K results in formation of Dy 3 (Fe, Si) 29 and also the compounds with the presumed composition of Dy 4 (Fe, Si) 41 and Ho 4 (Fe, Si) 41 . As this takes place the alloys contain a transition structure as well that represents a set of small-sized areas with various type short-range order in mutual displacement of Fe-Fe(Si) dumpbell chains. The process of phase formation at 1273 K is faced with difficulties. Even the annealing for 1000 h does not result in the state of equilibrium [ru

Synthesis, structure and magnetic properties of DyAl2 nanoparticles

International Nuclear Information System (INIS)

Zhang, W.S.; Brueck, E.; Zhang, Z.D.; Tegus, O.; Li, W.F.; Si, P.Z.; Geng, D.Y.; Klaasse, J.C.P.; Buschow, K.H.J.

2006-01-01

DyAl 2 nanoparticles have been prepared by means of arc discharge in a mixture of argon and hydrogen gas. The structure of DyAl 2 nanoparticles is studied by means of X-ray diffraction, X-ray photoelectron spectroscopy, and high-resolution transmission electron microscopy. X-ray photoelectron spectroscopy shows that the as-prepared DyAl 2 nanoparticles are coated with a layer of Al 2 O 3 phase on the surface, and their sizes vary from 20 nm to about 100 nm. The DyAl 2 nanoparticles exhibit ferromagnetic properties that are different from bulk DyAl 2 compound. The gradual decrease of the magnetization with increasing temperature in a wide temperature range reveals the size distribution of the DyAl 2 nanoparticles. The magnetic-entropy changes are derived from the isothermal magnetization curves measured at different temperatures. The magnetic-entropy change of the DyAl 2 nanoparticles is lower than that of the bulk DyAl 2 material but has a broadened peak

Electronic stability and reproducible accuracy of HARSHAW 2000(A,B) TLD-analyzer

International Nuclear Information System (INIS)

Yossef, S.K.; Henaish, B.A.

1985-01-01

Nowadays, the thermoluminescence techniques utilizing natural materials and assorted chemical compound of various geometrical configurations are widely and popularly used on the international scale as a dose evaluation system. The main problems which are usually encounting the accuracy of the evaluated dose by means of such various dosimeter forms are the long and short term stability of the measuring system. Also this manuscript is a very essential details stated out the principle mechanisms which cause that produced TL-readers instability. As it is stated out through the different sections of this issue, it is mainly due to the interior mechanisms of the TLD measuring systems. Further more, the various detailed discussions availed through the different sections of such issue are mainly accompanied by long term experiences gained by the authors. A novel heating cycle mechanism applied to HARSHOW 2000(A and b) TLD analyzer is tested experimentally. Also long and short term stability beside the reproducibility of the TLD reader system were experimentally tested under various seasonable environmental thermal conditions. The results of experimental measurements were noted for a total duration of six months during continuous operation of the TLD reader for one year. 1 fig., 3 tab

Dosimeter configurations for the measurement of H_s(0.07) and H_p(10) from photons

DEFF Research Database (Denmark)

Christensen, P.; Bøtter-Jensen, L.; Ennow, K.

1990-01-01

F TLD-700, LiF:Mg, Cu, P, and Li2B4O7:Mn TL detectors were investigated for the measurement of H(p) (10), and graphite-mixed MgB4O7:Dy, LiF and Li2B4O7 were investigated for the measurement of H(s) (0.07). Irradiations were made with a Co-60 gamma source and ISO qualities of X radiations...

New features in the spectrum of {sup 152}Dy

Energy Technology Data Exchange (ETDEWEB)

Galindo-Uribarri, A; Andrews, H R; Ball, G C; Radford, D C; Janzen, V P; Ward, D [Atomic Energy of Canada Ltd., Chalk River, ON (Canada). Chalk River Nuclear Labs.; Kuehner, J A; Mullins, S; Persson, L; Prevost, D; Waddington, J C [McMaster Univ., Hamilton, ON (Canada). Dept. of Physics; Drake, T E [Toronto Univ., ON (Canada). Dept. of Physics; Wyss, R [Joint Inst. for Heavy Ion Research, Oak Ridge, TN (United States)

1992-08-01

One of the most important recent developments in nuclear structure physics has been the prediction and observation of superdeformed (SD) shapes at high angular momentum in several nuclei in the rare earth region. The first experimental observation was a ridge-valley structure in a {gamma}-{gamma} coincidence matrix for the {sup 152}Dy nucleus. The ridge was found to be generated by sequences of stretched E2 transitions and corresponded to a moment of inertia J{sup (2)} of 85 {Dirac_h}{sup 2}MeV{sup -1}. Subsequently a discrete SD band was discovered in {sup 152}Dy and the lifetimes were measured. More recently the discovery of SD bands in several nuclei in the neighbourhood of {sup 152}Dy, the discovery of multiple SD bands in some nuclei, and the discovery of new SD regions at mass A {approx} 190 and A {approx} 140 have stimulated intense research activity in this area of nuclear physics. (author). 15 refs., 4 figs.

Room-temperature ferromagnetism in Dy films doped with Ni

Energy Technology Data Exchange (ETDEWEB)

Edelman, I. [Kirensky Institute of Physics, Siberian Division, Russian Academy of Sciences, Akademgorodok, Krasnoyarsk 660036 (Russian Federation)], E-mail: ise@iph.krasn.ru; Ovchinnikov, S. [Kirensky Institute of Physics, Siberian Division, Russian Academy of Sciences, Akademgorodok, Krasnoyarsk 660036 (Russian Federation); Siberian Federal University, Av. Svobodnyi 71, Krasnoyarsk 660074 (Russian Federation); Markov, V.; Kosyrev, N.; Seredkin, V.; Khudjakov, A.; Bondarenko, G. [Kirensky Institute of Physics, Siberian Division, Russian Academy of Sciences, Akademgorodok, Krasnoyarsk 660036 (Russian Federation); Kesler, V. [Institute of Semiconductor Physics, Siberian Division, Russian Academy of Sciences, Av. Akademika Lavrent' eva 13, Novosibirsk 630090 (Russian Federation)

2008-09-01

Temperature, magnetic field and spectral dependences of magneto-optical effects (MOEs) in bi-layer films Dy{sub (1-x)}Ni{sub x}-Ni and Dy{sub (1-x)}(NiFe){sub x}-NiFe were investigated, x changes from 0 to 0.06. Peculiar behavior of the MOEs was revealed at temperatures essentially exceeding the Curie temperature of bulk Dy which is explained by the magnetic ordering of the Dy layer containing Ni under the action of two factors: Ni impurities distributed homogeneously over the whole Dy layer and atomic contact of this layer with continues Ni layer. The mechanism of the magnetic ordering is suggested to be associated with the change of the density of states of the alloy Dy{sub (1-x)}Ni{sub x} owing to hybridization with narrow peaks near the Fermi level character for Ni.

Persistent luminescence, TL and OSL characterization of beta irradiated SrAl2O4:Eu2+, Dy3+ combustion synthesized phosphor

International Nuclear Information System (INIS)

Zúñiga-Rivera, N.J.; García, R.; Rodríguez-Mijangos, R.; Chernov, V.; Meléndrez, R.; Pedroza-Montero, M.; Barboza-Flores, M.

2014-01-01

The persistent luminescence (PLUM), thermoluminescence (TL) and optically stimulated luminescence (OSL) properties of strontium aluminates co-doped with Eu +2 and Dy +3 exposed to beta radiation is reported. The phosphor was synthesized by the combustion synthesis method employing a highly exothermic redox reaction between the metal nitrates [Al(NO 3 ) 3 , Sr(NO 3 ) 2 , Eu(NO 3 ) 3 and Dy(NO 3 ) 3 ] and organic fuel carbohydrazide (CH 6 N 4 O). The long decay PLUM emission, TL and OSL were measured as a function of beta radiation dose. A wide emission band centered at 510 nm (green) related to Eu 2+ ions and lattice defects were observed for the synthesized samples. The presence of a variety of defects and aggregates were responsible for the observed broad 100 °C peaked TL glow curve of the irradiated sample which is composed of several overlapped TL peaks. The existence of multiple trapping levels, with different trapping/detrapping probabilities, is behind the particular features for the PLUM, TL and OSL emissions. We conclude that in the SrAl 2 O 4 :Eu 2+ , Dy 3+ phosphors, the low temperature TL peaked around 30–75 °C is responsible for the PLUM emission and those around 100 °C were related to very stable trapping states which provide suitable radiation storage properties to be used as a PLUM/TL/OSL radiation phosphor

Paramagnetic scattering cross-sections of Nd and Dy at neutron wavelength between 0.5 A0 - 4 A0

International Nuclear Information System (INIS)

Maayouf, R.M.A.; Abdelkawy, A.; Adib, M.; Hamouda, I.

1984-01-01

The paramagnetic scattering cross-sections of Nd and Dy are calculated, for neutron wavelengths between 0.5-4 A, theoretically and deduced from available experimental data. The theoretical calculations are carried out using magnetic form factors deduced from Hartree-Fock radial wave functions for the 4 f electrons. The resulting theoretical curves of the paragnetic scattering cross-sections are compared with those deduced from data obtained using the transmission measurements. Both theoretical and experimental values found to be consistant

Comparative study of trapping parameters of LiF(TLD-100) from different production batches

Energy Technology Data Exchange (ETDEWEB)

Bos, A.J.J.; Piters, T.M.; Vries, W. de; Hoogenboom, J.E. (Delft Univ. of Technology (Netherlands). Interfaculty Reactor Institute)

1990-01-01

Computerised glow curve analysis has been used to determine the trapping parameters of the main peaks of the thermoluminescent (TL) material LiF(TLD-100). The TL material (solid state chips) originated from six different production batches with at least 19 chips per batch. The maxima of glow peaks 2 to 5 are found at the same temperature within very small limits. The activation energy and frequency factor of the main glow peak (peak 5) of TLD-100 originating from two batches differ significantly from those of the other four investigated batches. Nevertheless, the sensitivity of glow peak 5 is more or less the same for all batches. The trapping parameters of glow peaks 2 to 4 of TLD-100 vary little from batch to batch. The measured half-life of peak 2 differed strongly from batch to batch. For all investigated peaks no correlation has been found between glow peak sensitivity and trapping parameters. The results of this study suggest that both defect concentration and nature of the trapping centres vary from batch to batch. It would appear that as a consequence of selection by the manufacturer, the differences between the batches in terms of total light output are small. (author).

Calibration of TLD cards to beta ray spectra of 32P

International Nuclear Information System (INIS)

Ben-Shachar, B.; German, U.; Naim, E.

1994-01-01

The results of the evaluation of TLD chips are received in nC, and we need to transform these values to mGy, in order to obtain the penetrating and the non-penetrating dose. The calibration factors were determined experimentally by irradiation the TLD chips with an uranium source. Beta rays having other spectra can cause incorrect values when estimating the non-penetrating dose. If the spectrum of the beta source is known, a specific evaluation of the calibration factor can be performed. In this report, the estimation of the calibration factor for a 32 P source is presented. LiF:Ti,Mg TLD cards were irradiated calibrated source of 90 Sr/ 90 Y and 204 Tl and non-calibrated source of 32 P, in order to find the beta correction factor for the spectrum of 32 P. Calculations of the beta correction factor were performed too, by applying the Loevinger equations to the geometry of the TLD chips used in our routine measurements. The calculated values of the beta correction factors are lower than the experimental ones. When comparing the ratios, between the beta factors of 32 P and 90 Sr/ 90 Y received from the experiments and from the calculation, we found them to be constant up to ±5%. (authors) 15 refs, 2 figs, 6 tabs

Determination of radiation direction in environmental monitoring

International Nuclear Information System (INIS)

Campos, Vicente de Paulo de; Moura, Eduardo S.; Rocha, Felicia D.G.; Manzoli, Jose Eduardo

2009-01-01

The assessment of environmental exposure has been performed in Brazil using the thermoluminescence technique at Thermoluminescence Dosimetry Laboratory (LDT), at Nuclear and Energetic Research Institute (IPEN/CNEN-SP). To carry out these measurements, several thermoluminescent dosimeters (TLD's) were used to measure the expose. In this procedure, very few information of direction where the radiation came from is available. A vague supposition about the direction from where the radiation came from could be inferred only by evaluation of multiple dosimeters displaced at entire region of monitoring, but this demand to much effort or sometimes become impractical for certain situations. In this work, a single device is used to provide information about the direction from where the radiation came through. This device is called directional dosimeter (DD). Using more than one DD it is possible to reduce the uncertainty of the measurements and determine the radiation source position. The DD basically consists of a regular solid with high effective atomic number, where one TLD is positioned at each face. The DD allows evaluating the environmental exposure and the direction of the radiation by a simple vector sum. At each face of the DD, it is associated an orthogonal vector, and modulus of this vector represents the correspond exposure measured by the TLD. The direction of the radiation source is the sum of these faces vectors. The prototype used in this work was a lead cube with six TLDs of CaSO 4 :Dy/Teflon. The TLDs have high sensibility and are already used in area, environmental and personal monitoring. The measurements had shown the correct environmental exposure and a good indication of the radiation direction. (author)

Pulse monitor for upper extremities dosimetry in nuclear medicine

International Nuclear Information System (INIS)

Cledison de Jesus, Cunha; Divanizia do Nascimento, Souza

2006-01-01

In the manipulation of radioactive materials in Nuclear Medicine service the body parts of workers that are more displayed to the ionizing radiation are hands, underarm and arm. Therefore is necessary to developing personal dosimeters to monitoring of easy reproduction and low cost with purpose to determine the doses level radiation received by the worker in these extremities. However thermoluminescent dosimeters do not provide an instantaneous exposure reading, they are suitable for personal dosimetry because of their following advantages: wide useful dose range, small physical size and no need for high voltage or cables, i.e. stand alone character. The aim of this work is to investigation of a new pulse monitor, that has been developing with thermoluminescent detectors of CaSO 4 :Dy (TLD) using a small plate of acrylic, perforated cardboard to deposit the TLD. This set was involved in plastic to protect from humidity and other harmful ambient factors; moreover, a bracelet was inserted, adaptable for any worker. During the preparation of the personal dosimeters to monitor exposure it was necessary to verify their effectiveness to use by workers in a nuclear medicine service. The monitors have been submitted to procedures of performance evaluations by several tests: badges homogeneity, reproducibility, linearity, low detection limit, auto-irradiation, dosimeters stability, verification of the residual T.L. signal, visible light effect on dosimeters, energetic and angular dependence and TLD answer by influence of a simulator during radiation. Was possible to verify the efficiency of such upper extremities dosimeters and were obtained satisfactory results within of the limits demanded in the described tests above to this type of personal dosimeters. (authors)

Growth, structure and spectral properties of Dy3+-doped Li3Ba2La3(MoO4)8 crystal for potential use in solid-state yellow lasers

International Nuclear Information System (INIS)

Song, Mingjun; Wu, Mingyan; Zhou, Weiwei; Zhou, Xiaojing; Wei, Bo; Wang, Guofu

2014-01-01

Highlights: • Dy 3+ :Li 3 Ba 2 La 3 (MoO 4 ) 8 crystal was grown by the top seeded solution growth method. • The morphology, structure and spectral properties of the crystal were studied. • The main spectroscopic parameters were calculated by J–O theory and F–L formula. • The fluorescence dynamics was analyzed based on the Inokuti–Hirayama (I–H) model. • Comparisons with other reported crystals were made and the prospect was concluded. - Abstract: Dy 3+ :Li 3 Ba 2 La 3 (MoO 4 ) 8 crystal has been grown by the top seeded solution growth (TSSG) method from a flux of Li 2 MoO 4 and its morphology, structure and spectral properties were investigated. The crystal crystallizes in the monoclinic system with the space group C2/c, and the unit cell parameters are a = 5.3091(5), b = 13.0211(11), c = 19.3301(15), β = 90.891(7)°, V = 1336.1(2) Å 3 . Based on the Judd–Ofelt (J–O) theory and the Füchtbauer–Ladenburg (F–L) formula, the main spectroscopic parameters of Dy 3+ :Li 3 Ba 2 La 3 (MoO 4 ) 8 crystal, including the intensity parameters Ω t (t = 2, 4, 6), spontaneous emission probabilities, radiative lifetimes and emission cross sections were calculated and analyzed. The room temperature decay curve was analyzed through the frame work of the Inokuti–Hirayama (I–H) model and the results shows that electric dipole–dipole interaction is responsible for the energy transfer processes in Dy 3+ :Li 3 Ba 2 La 3 (MoO 4 ) 8 crystal

Nanophosphor CaSO4:Eu2+ for photoluminescence liquid crystal display (PLLCD)

Science.gov (United States)

Patle, Anita; Patil, R. R.; Moharil, S. V.

2018-05-01

In this work PL enhancement of CaSO4:Eu2+ nanophosphor which was synthesized with 0.01M molarity by co-precipitation method is presented. Synthesized phosphor was characterized by XRD, SEM, TEM and PL measurements. Average particle size is found to be in the range 80-100nm with Hexagonal morphology and PL studies showed emission peaks at 380nm, when samples were excited by 254nm. The observed PL emission is characteristic emission of Eu2+ similar to that observed in bulk CaSO4:Eu2. However under identical condition it is observed that intensity of emission get enhanced for 0.01M size which is doubled to that of 0.1M with similar emission at 380nm. A phosphor with narrow emission band around 390 nm is desirable, since at this wavelength the transmission of standard glass, polarizing plastic, other coating and LCD material is at acceptable level. Strong Eu2+ emission is observed in CaSO4:Eu nanophosphor which finds applications for PLLCD (photoluminescent liquid crystal display).

Determination of the TLD-100 physical parameters; Determinacion de parametros fisicos del TLD-100

Energy Technology Data Exchange (ETDEWEB)

Paucar J, J.; Picon C, C. [Instituto Nacional de Enfermedades Neoplasicas. INEN. Av. Angamos Este 2520, Lima 34 (Peru)

1998-12-31

This study was realized in the Physics service at the Radiotherapy Department of the National Institute of Neoplasic Diseases in Lima, Peru, it was determined the activation energy, the kinetic order and the frequency factor of the fifth peak of the TLD-100 thermoluminescent spectra using different algorithms. This was carried out in parallel with the implementation and design of a software and an interface associated with the Tl lecturer which allows a semiautomatic control for a thermoluminescent lecturer process. (Author)

Study of crystal structure and of dynamic behaviour in the various phases of TlD2PO4