WorldWideScience

Sample records for case study feasibility

  1. Moroccan wind farm potential feasibility. Case study

    International Nuclear Information System (INIS)

    Nouri, Abdellatif; Ait Babram, Mohamed; Elwarraki, Elmostafa; Enzili, Mustapha

    2016-01-01

    Highlights: • A new methodology for the technical feasibility of wind farm potentials is proposed. • The wind resources of two different sites in Morocco are compared. • Comparison between short and long term data using multivariate analysis is made. • Geographic information system implementation. • A 10 MW wind farm is designed and optimized. - Abstract: The subject of this paper is the elaboration of a methodology to study the technical feasibility of a wind farm potential. The implementation of this methodology allows a comparison between the wind resources of two different sites in Morocco. One site is located in the region of Essaouira, whereas the other one is located in the region of Safi. The comparison is based on real wind data collected from two masts at the heights of 30, 50, and 60 m. Each of the masts is installed at one of the mentioned potential sites over a fixed time period, lasting fifteen months for the first site, and eight months for the second one. The aim is the determination of the most applicable site presenting a good potential for a statistical study in order to predict long-term wind behaviors. Thus, the geographical situation study of the chosen site including topography, roughness and obstacles, is carried out. Furthermore, the wind resource using data, generated by the measuring masts, is evaluated. Finally, the areas which present great wind potential are located and the wind farm turbine locations are optimized by using the WAsP software.

  2. Feasibility study

    International Nuclear Information System (INIS)

    Gibbs, P.; Kalas, P.

    1975-01-01

    The feasibility study itself examines the technical, economic and financial implications of a nuclear power station in depth so as to make sure that nuclear power is the right course to take. This means that it is quite an expensive operation and it is to avoid wasting this money that a pre-feasibility study is carried out. This preliminary study should eliminate cases where the electrical system cannot absorb the capacity of a nuclear station of commercial size, where other sources of power such as hydro-electricity, gas or cheap coal would make nuclear obviously uneconomic or where no suitable sites exist. If this first rather simple survey shows that nuclear power is a credible solution to a utilities need for electricity or heat production plant, then the next stage is a full feasibility study. (orig./TK) [de

  3. Assessing feasibility of IT-enabled networked value consellations: A case study in the electricity sector

    NARCIS (Netherlands)

    Derzsi, Z.; Gordijn, J.; Kok, J.K.; Akkermans, J.M.; Tan, Y.H.; Krogstie, J.; Opdahl, A.L.; Sindre, G.

    2007-01-01

    Innovative networked value constellations, such as Cisco or Dell, are often enabled by Information Technology (IT). The same holds for the Distributed Electricity Balancing Service (DBS), which we present in this case study. To explore feasibility of such constellations while designing them, we need

  4. Case study on the feasibility of small and medium nuclear power plants in Egypt

    International Nuclear Information System (INIS)

    1994-04-01

    The IAEA agreed to co-operate with the Arab Republic of Egypt in performing a case study on the feasibility of small and medium power reactors (SMPRs) as a technical assistance project. The major objective of this study is to examine the feasibility of SMPRs to supply a portion of the future electrical energy requirements in the long term power programme of Egypt. The IAEA is grateful to all who provided information and assisted in the drafting and review of the report, in particular to the Advisory Group which performed the study in a co-operative effort. It is hoped that the report will meet the interests of policy makers, managers, engineers and economists in Member States, particularly in developing countries, and that it will provide a useful basis for specific studies to prepare decisions on SMPR projects. Refs, figs and tabs

  5. Promoting student case creation to enhance instruction of clinical reasoning skills: a pilot feasibility study

    Directory of Open Access Journals (Sweden)

    Chandrasekar H

    2018-04-01

    Full Text Available Hamsika Chandrasekar,1 Neil Gesundheit,2 Andrew B Nevins,3 Peter Pompei,4 Janine Bruce,5 Sylvia Bereknyei Merrell6 1Department of Pediatrics, Boston Children’s Hospital, Boston, MA, USA; 2Department of Medicine, Division of Endocrinology, Stanford University School of Medicine, Stanford, CA, USA; 3Department of Medicine, Division of Infectious Diseases, Stanford University School of Medicine, Stanford, CA, USA; 4Department of Medicine, Division of Primary Care and Population Health, Stanford University School of Medicine, Stanford, CA, USA; 5Department of Pediatrics, Stanford University School of Medicine, Stanford, CA, USA; 6Department of Surgery, Stanford University School of Medicine, Stanford, CA, USA Background: It is a common educational practice for medical students to engage in case-based learning (CBL exercises by working through clinical cases that have been developed by faculty. While such faculty-developed exercises have educational strengths, there are at least two major drawbacks to learning by this method: the number and diversity of cases is often limited; and students decrease their engagement with CBL cases as they grow accustomed to the teaching method. We sought to explore whether student case creation can address both of these limitations. We also compared student case creation to traditional clinical reasoning sessions in regard to tutorial group effectiveness, perceived gains in clinical reasoning, and quality of student–faculty interaction. Methods: Ten first-year medical students participated in a feasibility study wherein they worked in small groups to develop their own patient case around a preassigned diagnosis. Faculty provided feedback on case quality afterwards. Students completed pre- and post-self-assessment surveys. Students and faculty also participated in separate focus groups to compare their case creation experience to traditional CBL sessions. Results: Students reported high levels of team engagement

  6. Promoting student case creation to enhance instruction of clinical reasoning skills: a pilot feasibility study.

    Science.gov (United States)

    Chandrasekar, Hamsika; Gesundheit, Neil; Nevins, Andrew B; Pompei, Peter; Bruce, Janine; Merrell, Sylvia Bereknyei

    2018-01-01

    It is a common educational practice for medical students to engage in case-based learning (CBL) exercises by working through clinical cases that have been developed by faculty. While such faculty-developed exercises have educational strengths, there are at least two major drawbacks to learning by this method: the number and diversity of cases is often limited; and students decrease their engagement with CBL cases as they grow accustomed to the teaching method. We sought to explore whether student case creation can address both of these limitations. We also compared student case creation to traditional clinical reasoning sessions in regard to tutorial group effectiveness, perceived gains in clinical reasoning, and quality of student-faculty interaction. Ten first-year medical students participated in a feasibility study wherein they worked in small groups to develop their own patient case around a preassigned diagnosis. Faculty provided feedback on case quality afterwards. Students completed pre- and post-self-assessment surveys. Students and faculty also participated in separate focus groups to compare their case creation experience to traditional CBL sessions. Students reported high levels of team engagement and peer learning, as well as increased ownership over case content and understanding of clinical reasoning nuances. However, students also reported decreases in student-faculty interaction and the use of visual aids ( P study suggest that student-generated cases can be a valuable adjunct to traditional clinical reasoning instruction by increasing content ownership, encouraging student-directed learning, and providing opportunities to explore clinical nuances. However, these gains may reduce student-faculty interaction. Future studies may be able to identify an improved model of faculty participation, the ideal timing for incorporation of this method in a medical curriculum, and a more rigorous assessment of the impact of student case creation on the

  7. Case studies on the feasibility of the transient analysis system STAR in German nuclear power plants

    International Nuclear Information System (INIS)

    Buettner, W.E.; Felkel, L.; Zapp, A.

    1984-01-01

    On the basis of distubances which actually have occurred in German nuclear power plants a case-study has been performed to evaluate the feasibility of the computer-based disturbance analysis system STAR. By means of a compact plant simulator the disturbances collected have been remodelled and anlysed, on-line, with the disturbance analysis system STAR. In the last phase of the project experiments have been performed with reactor operators to get their reaction to, and opinion on, computerbased-operator aids. (orig.) [de

  8. International Case-Control Study of Adult Brain, Head and Neck Tumours: Results of the Feasibility Study (invited paper)

    International Nuclear Information System (INIS)

    Cardis, E.; Kilkenny, M.

    1999-01-01

    The objectives of the feasibility study were to collect and analyse the information necessary to assess the feasibility of a multi-centric study of adult head and neck tumours (including brain tumours) and mobile telephones. Information was obtained on the availability and accessibility of records from companies, the prevalence of mobile telephone use over time and the expected number of tumour cases in the proposed study regions. The conclusion is that it is feasible to develop a study of the relation between mobile telephone use and brain cancer risk. The feasibility of a study of the relation between radiofrequency exposure and cancer risk is, however, unclear at present. It is unknown whether a sufficiently accurate and precise RF exposure gradient can be derived to classify adequately each subject in the proposed study. A study of the relation between mobile telephone use and risk of salivary gland tumours and acoustic neurinomas is probably feasible, but more information is required about the logistic difficulties of ascertaining these cases in the study regions. Two subcommittees have been formed to develop the exposure measurement and epidemiological aspect of the study. (author)

  9. Feasibility study of Boron Nitride coating on Lithium-ion battery casing

    International Nuclear Information System (INIS)

    Saw, L.H.; Ye, Y.; Tay, A.A.O.

    2014-01-01

    Increasing in public awareness about global warming and exhaustion of energy resources has led to a flourishing electric vehicle industry that would help realize a zero-emission society. The thermal management of battery packs, which is an essential issue closely linked to a number of challenges for electric vehicles including cost, safety, reliability and lifetime, has been extensively studied. However, relatively little is known about the thermal effect of polymer insulation on the Lithium-ion battery casing. This study investigates the feasibility of replacing the polymer insulation with a Boron Nitride coating on the battery casing using the Taguchi experimental method. The effect of casing surface roughness, coating thickness and their interaction were examined using orthogonal array L 9 (3 4 ). Nominal the best is chosen for the optimization process to achieve optimum adhesion strength. In addition, the thermal improvements of the coating as compared to conventional polymer insulator on the battery are further investigated. - Highlights: • We studied the Boron Nitride coating on battery casing using Taguchi method. • We investigated the effect of surface roughness and coating thickness on adhesion strength. • We compared the effect of coating and polymer insulator in heat transfer. • The Boron Nitride coating could enhance the thermal management of the battery

  10. Planning for gasification of cellulosic wastes: Issues, feasibility and case study

    International Nuclear Information System (INIS)

    Staniewski, M.E.

    1993-01-01

    Gasification is presented as a concept that can assist municipalities and private companies to reduce the amount of solid waste generated and to utilize the cellulosic fraction of such waste as a biofuel. The technical and economic feasibility of cellulosic waste gasification is examined along with the implications associated with the environmental, social, and regulatory issues within a planning context. Study methods included a literature review, survey research employing nonstructured interviews, and a case study analysis. Opportunities for gasification are focused on regional governments in Ontario. The case study concentrated on the Regional Municipality of Waterloo. Regional governments in Ontario can benefit from utilizing the gasification concept to achieve a substantial reduction in the waste stream in an environmentally sound manner and contribute to solving worldwide problems associated with fossil fuel utilization. However, provincial and public acceptance will affect regional government decisions regarding gasification. Separate legislation should be enacted distinguishing gasification from incineration. In addition, the effectiveness of the environmental approval process must be improved; present procedures consume excess time and resources and act to discourage the involvement of public and private proponents. Public acceptance is likely to be affected by negative experiences associated with solid waste combustion. Nonbiased, reliable information is needed to clarify doubts and stress gasification's potential benefits. 85 refs., 15 figs., 26 tabs

  11. Feasibility of piezoelectric tiles adoption: A case study at Kuala Lumpur International Airport (KLIA) Malaysia

    Science.gov (United States)

    Chew, Boon Cheong; Loo, Heoy Shin; Bohari, Izyan Adilah; Hamid, Syaiful Rizal; Sukri, Fatin Hafizah; Kusumarwadani, Rini

    2017-03-01

    The basic function of an international airport is an aerodrome, provides not only the facilities for flights management, but also for customs and passport control. Nowadays, most of the international airports have established commercial outlets for food, products and services. As such, these airports are built with larger scale and more sophisticated on both infrastructure and infostructure which aim to be the most extensive air-travel service providers that connect the nations to the international gateways. Looking at the daily operations of an international airport, the energy consumption is apprehended to be enormous. Besides, knowing the fact that reliance on fossil fuels to power the airport buildings and to run the operations daily, this has led to many negative socioenvironmental implications. To date, some of the world major international airports have begun in renewable energy adoption-which mainly focused on solar energy as a way to reduce fossil energy consumption and towards greenhouse gases reduction. Inspired by thinking differently since solar energy has been adopted in Kuala Lumpur International Airport (KLIA) in 2014, through this study we proposed another form of renewable energy-piezoelectric technology adoption into our KLIA as a feasibility study. We believe that piezoelectric technology could complement the renewable energy mix, by tapping the crowd kinetic energy gathered internally in the airport buildings particularly at a few main entrances. Hence, the objectives of this study are (a) to examine the potential factors that will foster piezoelectric tiles adoption at KLIA and (b) to propose the ways for KLIA in speeding up piezoelectric tiles adoption within the airport terminals. The case study on the Malaysia Airports Holding Berhad (MAHB which manages the KLIA) was based on primary data collected through a series of qualitative focus group conducted on 14 (8 senior managers and 6 technical professionals) who were interested and supportive

  12. Important considerations for feasibility studies in physical activity research involving persons with multiple sclerosis: a scoping systematic review and case study.

    Science.gov (United States)

    Learmonth, Yvonne C; Motl, Robert W

    2018-01-01

    Much research has been undertaken to establish the important benefits of physical activity in persons with multiple sclerosis (MS). There is disagreement regarding the strength of this research, perhaps because the majority of studies on physical activity and its benefits have not undergone initial and systematic feasibility testing. We aim to address the feasibility processes that have been examined within the context of physical activity interventions in MS. A systematic scoping review was conducted based on a literature search of five databases to identify feasibility processes described in preliminary studies of physical activity in MS. We read and extracted methodology from each study based on the following feasibility metrics: process (e.g. recruitment), resource (e.g. monetary costs), management (e.g. personnel time requirements) and scientific outcomes (e.g. clinical/participant reported outcome measures). We illustrate the use of the four feasibility metrics within a randomised controlled trial of a home-based exercise intervention in persons with MS. Twenty-five studies were identified. Resource feasibility (e.g. time and resources) and scientific outcomes feasibility (e.g. clinical outcomes) methodologies were applied and described in many studies; however, these metrics have not been systematically addressed. Metrics related to process feasibility (e.g. recruitment) and management feasibility (e.g. human and data management) are not well described within the literature. Our case study successfully enabled us to address the four feasibility metrics, and we provide new information on management feasibility (i.e. estimate data completeness and estimate data entry) and scientific outcomes feasibility (i.e. determining data collection materials appropriateness). Our review highlights the existing research and provides a case study which assesses important metrics of study feasibility. This review serves as a clarion call for feasibility trials that will

  13. Assuring consumer safety without animal testing: a feasibility case study for skin sensitisation.

    Science.gov (United States)

    Maxwell, Gavin; Aleksic, Maja; Aptula, Aynur; Carmichael, Paul; Fentem, Julia; Gilmour, Nicola; Mackay, Cameron; Pease, Camilla; Pendlington, Ruth; Reynolds, Fiona; Scott, Daniel; Warner, Guy; Westmoreland, Carl

    2008-11-01

    Allergic Contact Dermatitis (ACD; chemical-induced skin sensitisation) represents a key consumer safety endpoint for the cosmetics industry. At present, animal tests (predominantly the mouse Local Lymph Node Assay) are used to generate skin sensitisation hazard data for use in consumer safety risk assessments. An animal testing ban on chemicals to be used in cosmetics will come into effect in the European Union (EU) from March 2009. This animal testing ban is also linked to an EU marketing ban on products containing any ingredients that have been subsequently tested in animals, from March 2009 or March 2013, depending on the toxicological endpoint of concern. Consequently, the testing of cosmetic ingredients in animals for their potential to induce skin sensitisation will be subject to an EU marketing ban, from March 2013 onwards. Our conceptual framework and strategy to deliver a non-animal approach to consumer safety risk assessment can be summarised as an evaluation of new technologies (e.g. 'omics', informatics), leading to the development of new non-animal (in silico and in vitro) predictive models for the generation and interpretation of new forms of hazard characterisation data, followed by the development of new risk assessment approaches to integrate these new forms of data and information in the context of human exposure. Following the principles of the conceptual framework, we have been investigating existing and developing new technologies, models and approaches, in order to explore the feasibility of delivering consumer safety risk assessment decisions in the absence of new animal data. We present here our progress in implementing this conceptual framework, with the skin sensitisation endpoint used as a case study. 2008 FRAME.

  14. Study of geological details towards feasibility of uranium project: Indian case studies

    International Nuclear Information System (INIS)

    Sarangi, A.

    2014-01-01

    Appropriate technical evaluation of geological details at early stage of exploration is the key to minimising the lead-time between discovery and production. This has a major influence on economic viability of the deposits. Indian uranium deposits are of medium-tonnage and low-grade occurring in dissimilar geological provinces. Detailed studies of geological characteristics of these deposits are very vital to the proper selection of technology and subsequent successful operation. The method of mining (underground/open pit/in-situ recovery) is influenced by the ore body depth, size, grade, configuration, hostrock and adjoining strata characteristics, hydrological condition etc. The ore processing technology is also subjective to mineralogical characteristics of the ore. In order to draw the flowsheet, determine process parameters and selection of reagents, a comprehensive study on identification of minerals and their probable metallurgical characteristics, general physical relationship between various minerals, mineral liberation size etc is of great significance. The technology for disposal of tailings is also influenced by geological/geo-hydrological characteristics. The key to successful operation of Indian uranium deposits lies in outlining a pre-development strategy as the exploration advances to different stages. This phase called ''exploratory mining'' - which starts with detailed exploration and ends with approval of the project is very critical for early commissioning of the project. The activities during this period include collection of representative drill core samples during exploration, laboratory studies, geo-technical studies and determination of geomechanical properties of ore and waste rock etc. Later, the ore lenses are accessed through limited entry(ies). Developments along the ore body helps in better understanding of the configuration of the lenses. Studies for strata control in case of underground mining are carried out towards deciding the

  15. Techno-economic feasibility study of the integration of a commercial small-scale ORC in a real case study

    International Nuclear Information System (INIS)

    Cavazzini, G.; Dal Toso, P.

    2015-01-01

    Highlights: • The integration of a small-scale commercial ORC in a real case study was analyzed. • The possibility of recovering the waste heat produced by an ICE was considered. • A semi-empirical steady-state model of the commercial small scale ORC was created. • Both direct and indirect costs was considered in the business model. • The ORC integration was not economically feasible due to increased indirect costs. - Abstract: The ORC certainly represents a promising solution for recovering low-grade waste heat in industries. However, the efficiency of commercial small-scale ORC solutions is still too low in comparison with the high initial costs of the machine and the lack of simulation models specifically developed for commercial ORC systems prevents industries from defining an accurate business model to correctly evaluate the ORC integration in real industrial processes. This paper presents a techno-economic feasibility analysis of the integration of a small-scale commercial ORC in a real case study, represented by a highly-efficient industrial distillery. The integration is aimed at maximizing the electricity auto-production by exploiting the heat produced by an internal combustion engine, already partially recovered in internal thermal processes. To analyze the influence of the ORC integration on the industrial processes, a semi-empirical steady-state model of the commercial small scale ORC was created. The model made it possible to simulate the performance of the commercial ORC within a hypothetical scenario involving the use of the heat from the cooling water and from the exhaust gases of the internal combustion engine. A detailed thermo-dynamic analysis has been carried out to study the effects of the ORC integration on the plant’s energy system with particular focus on the two processes directly affected by ORC integration, namely vapor production and the drying process of the grape marc. The analysis highlighted the great importance in the

  16. Feasibility and Sustainability of Community Based Health Insurance in Rural Areas Case Study of Musana, Zimbabwe

    Directory of Open Access Journals (Sweden)

    Lazarus MUCHABAIWA

    2017-12-01

    Full Text Available The Zimbabwe Demographic Health Survey (ZDHS 2010-11 showed that only 6 percent of the population is covered by health insurance in Zimbabwe. This study investigated the feasibility, acceptability and sustainability of Community Based Health Insurance (CBHI as an alternative to pooling risk and financing social protection in Zimbabwe. Willingness to Pay (WTP for health insurance and socioeconomic data were collected through interviews with 121 household heads selected using a 2-stage sampling procedure on 14 villages in Musana and Domboshava rural areas, a population which is largely unemployed and reliant on subsistence agriculture. A CBHI scheme was established and followed up for 3 years documenting data on visits made, financial contributions from recruited households and their actual health expenditures. Findings indicate that CBHI is generally accepted as a means of health insurance in rural communities. The median willingness to pay for health insurance was $5.43 against monthly expenditures ranging of up to $180. The low WTP is attributable to low incomes as only 3.4 percent of the respondents relied on formal employment. Trust issues, adverse selection, moral hazard, and administration costs were challenges threatening sustainability of CBHI. A financial gap averaging 42% was generally on a downward trend and was closed by the end of the follow-up study as contributions were equivalent to medical expenses. We conclude that CBHI is feasible, has potential for sustainability and should be considered as a springboard for the planned Zimbabwean National Health Insurance.

  17. Self-rostering applied to case studies - An ILP method to construct a feasible schedule

    NARCIS (Netherlands)

    Uijland, Suzanne; van der Veen, Egbert; Hurink, Johann L.; Schutten, Johannes M.J.; Kjenstad, D.; Riise, A.; Nordlander, T.E.; McCollum, B.; Burke, E.

    We discuss the self-rostering problem, a concept receiving more and more attention from both theory and practice. We outline our methodology and discuss its application to a number of practical case studies.

  18. General discussion of feasibility study

    International Nuclear Information System (INIS)

    Calori, F.

    1976-01-01

    Fundamentals, objectives and parameters of feasibility studies in the field of nuclear power project planning are discussed in a general way. Technical and economic problems to be considered are pointed out. In special cases, IAEA offers its aid and support. (UA) [de

  19. Case Study Application of the Biodiversity Security Index to Ranking Feasibility Studies for Ecosystem Restoration Projects of the U.S. Army Corps of Engineers

    Science.gov (United States)

    2016-04-01

    ER D C/ EL C R- 16 -1 Ecosystem Management and Restoration Research Program Case Study Application of the Biodiversity Security Index... Biodiversity Security Index to Ranking Feasibility Studies for Ecosystem Restoration Projects of the U.S. Army Corps of Engineers Richard A. Cole... Biodiversity Security Index (BSI) was applied to 23 project sites ranked for restoration feasibility study annual funding by the U. S. Army Corps of

  20. Feasibility and results of a case study of yoga to improve physical functioning in people with chronic traumatic brain injury.

    Science.gov (United States)

    Schmid, Arlene A; Miller, Kristine K; Van Puymbroeck, Marieke; Schalk, Nancy

    2016-01-01

    The purpose of this mixed-methods case study was to investigate whether an 8-week 1:1 yoga program was feasible and beneficial to people with traumatic brain injury (TBI). This was a mixed-methods case study of one-to-one yoga for people with TBI included three people. We completed assessments before and after the 8-week yoga intervention and included measures of balance, balance confidence, pain, range of motion, strength and mobility. Qualitative interviews were included at the post-assessment. We include a percent change calculation and salient quotes that represent the perceived impact of the yoga intervention. All participants completed the yoga intervention and all demonstrated improvements in physical outcome measures. For the group, balance increased by 36%, balance confidence by 39%, lower extremity strength by 100% and endurance by 105%. Qualitative data support the use of yoga to improve multiple aspects of physical functioning, one participant stated: "I mean it's rocked my world. It's changed my life. I mean all the different aspects. I mean physically, emotionally, mentally, it's given me you know my life back…". Yoga, delivered in a one-to-one setting, appears to be feasible and beneficial to people with chronic TBI. Chronic traumatic brain injury (TBI) leads to many aspects of physical functioning impairment. Yoga delivered in a one-to-one setting may be feasible and beneficial for people with chronic TBI.

  1. Feasibility analysis of a system of education B-learning: case study University of san Buenaventura

    Directory of Open Access Journals (Sweden)

    Lilian Karina DeArco-Paternina

    2017-07-01

    Full Text Available This article describes the feasibility of implementing the educational modality known as Blended learning in the specialization of petroleum refining and basic petrochemical processes engineering at the University of San Buenaventura, Cartagena branch. For this purpose, information was collected through virtual surveys carried out on the target population, the study of the economic and financial viability of the project was carried out and the results were presented to the corresponding entities of the University. Within the study, we identified nine drivers or agents motivating decision as well as the financial viability obtained through indicators such as net present value and internal rate of return. As a result, it was determined that the implementation of this modality creates a great business opportunity for the University, aligned with its corporate education strategy and with a spirit of service to the community. Consequently, this specialization could be carried out in the B-learning mode, due to the lack of time of the target population to attend one hundred percent classroom sessions and to the fact that the institution has the technological platform, financial support and Nationwide recognition.

  2. Analysis of economic feasibility of sale of surplus electricity in cogeneration: case study

    International Nuclear Information System (INIS)

    Fodra, Marcelo; Esperancini, Maura Seiko Tsutsui

    2010-01-01

    The production of energy in large quantity and at competitive prices is crucial for economic development, which allied to the environmental question, has incentivated the use of renewable sources of energy. One of the most promising sources of renewable energy is the cogeneration from the residues of cane. Currently, the scenario for this kind of energy production is not consolidated, as production prices are not stable, inducing a risky situation for the environment. This work was aimed to study the economic viability of installing a main site for cogeneration of electricity, in a regional sugarcane factory located in the central region of Sao Paulo state that currently uses residues of sugar cane as fuel. The risk factor that was taken into consideration was the price paid for the MWh sold to the Chamber of Commerce of Electricity. The Monte Carlo Method was used to assess the risk factors for the analysis, by using of New Present Value (NPV), in a scenario that uses 20% of the initial investment made by the energy dealer. After the simulations were finished, considering the conditions used in this work, the project tends to be not feasible, as the behavior of the prices of cogenerated MWh are not sufficient for paying the initial investment and the operational costs. (author)

  3. Feasibility and early outcomes of laparoscopic plicated sleeve gastrectomy: a case-control study

    Directory of Open Access Journals (Sweden)

    Tomasz Rogula

    2016-01-01

    Full Text Available Introduction : Sleeve gastrectomy (SG continues to gain popularity as a viable weight loss procedure with well-documented outcomes and procedure-specific adverse effects. It has become increasingly indicated for the treatment of morbid obesity. Aim of the research : To compare a novel approach to SG, which aims to reduce SG-specific complications, to the standard SG procedure. Material and methods : Sixteen morbidly obese patients with a mean body mass index (BMI of 48.5 kg/m 2 ± SD who underwent the novel laparoscopic plicated sleeve gastrectomy (LPSG were retrospectively studied. The control group included 18 patients who underwent laparoscopic SG. Study and control groups were matched for BMI and gender. Study group patients underwent a partial SG with imbrication of the distal 2/3 of the staple line with 2 cm overlap and 3–4 cm of the pre-pyloric stomach. Control group SG patients had their staple line oversewn without plication. Outcomes at 3, 6 and 12 months were compared and analyzed. Results: There was no statistically significant difference in weight loss at 12 months between the LPSG and SG groups. Postoperative nausea was comparable between the two groups. No major complications were noted in either group. Conclusions: The LPSG is a modification of the standard SG which has comparable outcomes, safety and feasibility. It may lead to a decrease in unwanted complications such as sleeve stricture or obstruction. Further studies on long-term outcomes are needed to assess its value as a bariatric procedure.

  4. A Feasibility Assessment of Photovoltaic Power Systems in Ireland; a Case Study for the Dublin Region

    Directory of Open Access Journals (Sweden)

    Fionnuala Murphy

    2017-02-01

    Full Text Available Photovoltaic (PV power generation is one of the cleanest sources for producing renewable energy; however uptake on the Irish renewable energy market to date has been low. There is a lack of support for solar PV systems in Ireland; there is currently no solar PV energy feed-in-tariff as there are for other renewable energy systems in Ireland. Despite the current lack of support, the Government has indicated that support for the uptake of solar PV installations will be provided through the provision of a feed-in tariff in the future. The aim of this study was to determine the feasibility of installing PV systems under Irish climatic conditions at a location based in Dublin, Ireland, from a technical, environmental and economic point of view. This was achieved by carrying out a life cycle assessment of potential environmental impacts, and analysis of energy and economic payback times relating to the proposed PV system. Four possible renewable feed-in-tariffs (based on existing feed-in-tariffs for other renewable energy systems were considered to determine the effect of such tariffs on the overall economics of the proposed PV system. Results show that life cycle GHG emissions are 69 g CO2-eq per kWh generated by the system, significantly lower than the current electricity grid mix emissions of 469 g CO2-eq per kWh. It will take 5.23 years of operation of the solar plant to generate the same amount of energy (in terms of primary energy equivalent that was used to produce the system itself. The economic payback time varies from 19.3 and 34.4 years depending on the rate of renewable energy feed-in-tariff applied. The costs for the production of PV electricity in this study are higher than is usual in countries where the solar PV market is more developed, e.g., Germany, due to constraints with building integration and lack of experienced PV installers. As more PV is deployed, the Irish PV installer base will increase and ‘learning by doing’ effects

  5. Spermatic feasibility after 20 years of freezing and refreezing: case study

    Directory of Open Access Journals (Sweden)

    Paulo Franco Taitson

    2010-08-01

    Full Text Available The aim of the present work was to study the spermatic feasibility after 20 years of freezing, thawing and refreezing. A young man affected by testicular cancer sought the sperm freezing service. After 20 years, the samples were thawed and frozen again. After two days, thawing and analysis of the material took place. Comparison of the findings showed activity reduction from the first thawing to the fresh semen 59.09%. For the second thawing it was 77.27%. Considering the morphology, first thawing showed a reduction of 44.64% in relation to fresh semen. In the second thawing, the reduction was of 75%. Spermatic motility decreased by 64.28% in relation to fresh semen and 92.85% at the level of second thawing. The patient had gone through in vitro fertilization in 2007, obtaining success in the first one attempt.Este trabalho mostra a viabilidade espermática após 20 anos de congelamento seminal, descongelamento e novo congelamento. Jovem do sexo masculino afetado por câncer testicular procurou o serviço para congelamento de espermatozóides. Após vinte anos, as amostras foram descongeladas e congeladas novamente. Após dois dias, realizou-se um novo descongelamento e análise do material. As comparações dos resultados mostraram uma redução da atividade do primeiro descongelamento ao semen fresco em 59,09%. A partir do segundo descongelamento era de 77,27%. Considerando a morfologia, o primeiro descongelamento mostrou uma redução de 44,64% em relação ao sêmen fresco. No segundo descongelamento, a redução foi de 75%. A motilidade espermática diminuiu 64,28% em relação ao semen fresco e 92,85% a nível do segundo descongelamento. O paciente passou por fertilização in vitro em 2007, obtendo sucesso na primeira tentativa.

  6. A pre-feasibility case study on integrated resource planning including renewables

    International Nuclear Information System (INIS)

    Yilmaz, Pelin; Hakan Hocaoglu, M.; Konukman, Alp Er S.

    2008-01-01

    In recent years, economical and environmental constraints force governments and energy policy decision-makers to change the prominent characteristics of the electricity markets. Accordingly, depending on local conditions on the demand side, usage of integrated resource planning approaches in conjunction with renewable technologies has gained more importance. In this respect, an integrated resource planning option, which includes the design and optimization of grid-connected renewable energy plants, should be evaluated to facilitate a cost-effective and green solution to a sustainable future. In this paper, an integrated resource planning case is studied for an educational campus, located in Gebze, Turkey. It is found that for the considered campus, the integrated resource planning scenario that includes renewables as a supply-side option with existing time-of-use tariff may provide a cost-effective energy production, particularly for the high penetration level of the renewables

  7. Feasibility studies and technological innovation

    DEFF Research Database (Denmark)

    Hvelplund, Frede Kloster; Lund, Henrik; Sukkumnoed, Decharut

    2004-01-01

    The chapter offers a tool to conduct feasibility studies and focuses on how to make feasibility studies in a situation with environmental concerns, in which technological innovation and institutional chnages are among the objectives.......The chapter offers a tool to conduct feasibility studies and focuses on how to make feasibility studies in a situation with environmental concerns, in which technological innovation and institutional chnages are among the objectives....

  8. Technical and economic feasibility of superconducting power transmission: a case study

    International Nuclear Information System (INIS)

    Forsyth, E.B.; Mulligan, G.A.; Beck, J.W.; Williams, J.A.

    1975-01-01

    The long-range plans of the Long Island Lighting Company include the installation of 4600 MW of generation capacity at nuclear sites on eastern Long Island by the 1990's. A single site, Shoreham, was chosen for this study which would require transmission facilities to the Ruland Road substation, 43 miles away. Conventional 345 kV overhead and underground circuits are planned for this service. For the case study three superconducting cable schemes have been investigated which reflect various technical options. The superconducting cables have been designed to meet acceptable normal and contingency load flow conditions and to withstand maximum short circuit faults. A cost analysis has been made of the complete installation, providing a valuable comparison of the estimated cost of this new technology with conventional methods. The most favorable cost comparison is a two-circuit 345 kV superconducting system, which appears to be about one-half the cost of an all underground 345 kV high pressure oil-filled cable system. No reactive compensation will be required for the superconducting system, whereas extensive compensation is required for HPOF cables over the same distance. The cost estimate for the two-circuit superconducting system is about twice that of 345 kV overhead transmission, which would consist of two double circuits and one single circuit, assuming right-of-way could be obtained. (U.S.)

  9. [A case study regarding the technical and public health feasibility of collecting water from fog].

    Science.gov (United States)

    García-Ubaque, César A; Vaca-Bohórquez, Martha L; García-Ubaque, Juan C

    2013-01-01

    Evaluating the collection of water for human consumption from fog nets in San Antonio (Cundinamarca department). Water was collected from fog using a prototype 6 m²sensor unit which was installed In the area for 53 days; this water was analysed to assess its quality regarding human consumption. The collection area's average daily volume was 43.26 L/day and the parameters evaluated met the minimum values established by local regulations for drinking water (RAS 2000), except for pH. This technique represents an alternative for obtaining water fit for human consumption and can be scaled-up to produce the quantity needed for communities living in low rainfall areas. It can thereby lead to improving such populations' health conditions. Its economic feasibility should thus be assessed regarding its implementation and sustainability.

  10. Ambulatory (24 h) blood pressure and arterial stiffness measurement in Marfan syndrome patients: a case control feasibility and pilot study.

    Science.gov (United States)

    Hillebrand, Matthias; Nouri, Ghazaleh; Hametner, Bernhard; Parragh, Stephanie; Köster, Jelena; Mortensen, Kai; Schwarz, Achim; von Kodolitsch, Yskert; Wassertheurer, Siegfried

    2016-05-06

    The aim of this work is the investigation of measures of ambulatory brachial and aortic blood pressure and indices of arterial stiffness and aortic wave reflection in Marfan patients. A case-control study was conducted including patients with diagnosed Marfan syndrome following Ghent2 nosology and healthy controls matched for sex, age and daytime brachial systolic blood pressure. For each subject a 24 h ambulatory blood pressure and 24 h pulse wave analysis measurement was performed. All parameters showed a circadian pattern whereby pressure dipping was more pronounced in Marfan patients. During daytime only Marfan patients with aortic root surgery showed increased pulse wave velocity. In contrast, various nighttime measurements, wave reflection determinants and circadian patterns showed a significant difference. The findings of our study provide evidence that ambulatory measurement of arterial stiffness parameters is feasible and that these determinants are significantly different in Marfan syndrome patients compared to controls in particular at nighttime. Further investigation is therefore indicated.

  11. Modeling the Economic Feasibility of Large-Scale Net-Zero Water Management: A Case Study.

    Science.gov (United States)

    Guo, Tianjiao; Englehardt, James D; Fallon, Howard J

      While municipal direct potable water reuse (DPR) has been recommended for consideration by the U.S. National Research Council, it is unclear how to size new closed-loop DPR plants, termed "net-zero water (NZW) plants", to minimize cost and energy demand assuming upgradient water distribution. Based on a recent model optimizing the economics of plant scale for generalized conditions, the authors evaluated the feasibility and optimal scale of NZW plants for treatment capacity expansion in Miami-Dade County, Florida. Local data on population distribution and topography were input to compare projected costs for NZW vs the current plan. Total cost was minimized at a scale of 49 NZW plants for the service population of 671,823. Total unit cost for NZW systems, which mineralize chemical oxygen demand to below normal detection limits, is projected at ~$10.83 / 1000 gal, approximately 13% above the current plan and less than rates reported for several significant U.S. cities.

  12. Post Feed-in Scheme Photovoltaic System Feasibility Evaluation in Italy: Sicilian Case Studies

    Directory of Open Access Journals (Sweden)

    Riccardo Squatrito

    2014-11-01

    Full Text Available Thanks to national energy policies, over recent years the Italian photovoltaic (PV sector has undergone an extraordinary growth, also affecting the primary sector. In this context, Mediterranean greenhouses are well-adapted to photovoltaic systems because they represent one of the most energy-intensive sectors in agriculture. The Italian feed-in scheme ended at the beginning of 2013, making it necessary to investigate the feasibility of photovoltaic systems devoid of any electricity production-related incentives. In this paper, production cost and profitability analyses of photovoltaic electricity have been conducted, considering Mediterranean solar greenhouses in which, thanks to net metering, all the electricity produced by photovoltaic panels is self-consumed. Our results showed that grid parity is already reached for Sicilian PV systems with a capacity greater than 50 kW. Moreover, net present value, internal rate of return and discounted payback time all demonstrate the high economic convenience of all the photovoltaic investments analyzed, due to the huge savings on energy expenditures.

  13. Factors that can influence the economic feasibility of stand-alone and grid-connected photovoltaic systems: case studies using the software AVES-F

    International Nuclear Information System (INIS)

    Blasques, L.C.M.; Pinho, J.T.

    2004-01-01

    This paper presents case studies of economic feasibility of solar photovoltaic systems using the software AVES-F (Analysis of Economic Feasibility of Photovoltaic Systems), developed by the authors, considering cases of stand-alone and grid-connected systems. The software takes into account several factors that can influence the economic feasibility of these kind of systems, like load to be supplied, distance to the grid, the use regime of the system, applied subsidies and others. The main goal of this paper is to analyze some of these factors and to observe how they can affect the economics of PV systems for electricity generation. (authors)

  14. Case study feasibility analysis of the Pelamis wave energy convertor in Ireland, Portugal and North America

    International Nuclear Information System (INIS)

    Dalton, G.J.; Alcorn, R.; Lewis, T.

    2010-01-01

    The performance and economic viability of the Pelamis wave energy converter (WEC) has been investigated over a 20 year project time period using 2007 wave energy data from various global locations: Ireland, Portugal, USA and Canada. Previous reports assessing the Pelamis quote a disparate range of financial returns for the Pelamis, necessitating a comparative standardised assessment of wave energy economic indicators. An Excel model (NAVITAS) was created for this purpose which estimated the annual energy output of Pelamis for each location using wave height (H s ) and period (T z ) data, and produced financial results dependant on various input parameters. The economic indicators used for the analysis were cost of electricity (COE), net present value (NPV) and internal rate of return (IRR), modelled at a tariff rate of EUR0.20/kWh. Analysis of the wave energy data showed that the highest annual energy output (AEO) and capacity for the Pelamis was the Irish site, as expected. Portugal returned lower AOE similar to the lesser North American sites. Monthly energy output was highest in the winter, and was particularly evident in the Irish location. Moreover, the difference between the winter wave energy input and the Pelamis energy output for Ireland was also significant as indicated by the capture width, suggesting that Pelamis design was not efficiently capturing all the wave energy states present during that period. Modelling of COE for the various case study locations showed large variation in returns, depending on the number of WEC modelled and the initial cost input and learning curve. COE was highest when modelling single WEC in comparison to multiples, as well as when using 2004 initial costs in comparison to 2008 costs (at which time price of materials peaked). Ireland returned the lowest COE of EUR0.05/kWh modelling over 100 WEC at 2004 cost of materials, and EUR0.15/kWh at 2008 prices. Although favourable COE were recorded from some of the modelled scenarios

  15. Feasibility studies for decommissioning

    International Nuclear Information System (INIS)

    Hladky, E.

    2000-01-01

    In this presentation author deals with planning of decommission of the NPPs A1, V1 and V2 Bohunice and Mochovce. It was concluded that: Used model for decommissioning parameters assessment has been suitable for elaboration of initial decommissioning plans (feasibility studies); Basic assessment of main decommissioning parameters and basic comparison of various decommissioning options have been possible; Improvement of the model and corresponding software is desirable and works on software improvement began one year ago; V1-NPP initial decommissioning plan should be actualized, because initial decommissioning plan does not correspond by its content and structure to requirements of Act No. 130/98 and Nuclear Regulatory Authority Degree No. 246/99; Strategy of radioactive wastes treatment and conditioning together with technical provisions at Jaslovske Bohunice site was changed in comparison with the assumptions in 1991-92; Considered V1 NPP decommissioning options are necessary to be re-evaluated in accordance with latest development of knowledge and approaches to NPP decommissioning in the world; Specific unit costs are substantially and differentially changed in comparison with the assumptions in 1991-92; Necessity to take into account technical changes resulted from V1 NPP reconstruction. (author)

  16. Economic feasibility study for improving drinking water quality: a case study of arsenic contamination in rural Argentina.

    Science.gov (United States)

    Molinos-Senante, María; Perez Carrera, Alejo; Hernández-Sancho, Francesc; Fernández-Cirelli, Alicia; Sala-Garrido, Ramón

    2014-12-01

    Economic studies are essential in evaluating the potential external investment support and/or internal tariffs available to improve drinking water quality. Cost-benefit analysis (CBA) is a useful tool to assess the economic feasibility of such interventions, i.e. to take some form of action to improve the drinking water quality. CBA should involve the market and non-market effects associated with the intervention. An economic framework was proposed in this study, which estimated the health avoided costs and the environmental benefits for the net present value of reducing the pollutant concentrations in drinking water. We conducted an empirical application to assess the economic feasibility of removing arsenic from water in a rural area of Argentina. Four small-scale methods were evaluated in our study. The results indicated that the inclusion of non-market benefits was integral to supporting investment projects. In addition, the application of the proposed framework will provide water authorities with more complete information for the decision-making process.

  17. Economic and financial feasibility of wind energy - Case study of Philippines

    Energy Technology Data Exchange (ETDEWEB)

    Painuly, J. P. [Risoe National Lab., DTU, UNEP Risoe Centre, Roskilde (Denmark)

    2007-05-15

    The financial viability of a 30 MW wind farm proposed to be set-up in St. Ana in Philippines was examined. It was found that project is viable if established by a company with a low hurdle rate (8.68%) and good reach to avail low cost financing from domestic financial institutions, who may have such packages for low-risk customers. Most of the private sector investors however have higher discount rates due to high financing costs, and higher risk premiums charged by financers. The viability was an issue at risk adjusted discount rate of 13.2%, a typical rate for private sector investors in Philippines. Scenarios for variation in base parameters as well for a variety of financial packages, including revenues from CDM were run. Although CDM revenues improve attractiveness of the project, viability remains an issue. A financing package, that may have a grant component (as with the Danida package in the past), can help project make viable in this case. (au)

  18. GINGER: A feasibility study

    Science.gov (United States)

    Di Virgilio, Angela D. V.; Belfi, Jacopo; Ni, Wei-Tou; Beverini, Nicolo; Carelli, Giorgio; Maccioni, Enrico; Porzio, Alberto

    2017-04-01

    GINGER (Gyroscopes IN General Relativity) is a proposal for an Earth-based experiment to measure the Lense-Thirring (LT) and de Sitter effects. GINGER is based on ring lasers, which are the most sensitive inertial sensors to measure the rotation rate of the Earth. We show that two ring lasers, one at maximum signal and the other horizontal, would be the simplest configuration able to retrieve the GR effects. Here, we discuss this configuration in detail showing that it would have the capability to test LT effect at 1%, provided the accuracy of the scale factor of the instrument at the level of 1 part in 1012 is reached. In principle, one single ring laser could do the test, but the combination of the two ring lasers gives the necessary redundancy and the possibility to verify that the systematics of the lasers are sufficiently small. The discussion can be generalised to seismology and geodesy and it is possible to say that signals 10-12 orders of magnitude below the Earth rotation rate can be studied; the proposed array can be seen as the basic element of multi-axial systems, and the generalisation to three dimensions is feasible adding one or two devices and monitoring the relative angles between different ring lasers. This simple array can be used to measure with very high precision the amplitude of angular rotation rate (the length of the day, LOD), its short term variations, and the angle between the angular rotation vector and the horizontal ring laser. Finally this experiment could be useful to probe gravity at fundamental level giving indications on violations of Einstein Equivalence Principle and Lorenz Invariance and possible chiral effects in the gravitational field.

  19. North America grid segmentation case studies : technical feasibility and economics of implementation

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, A.L. [Bonneville Power Administration, Portland, OR (United States); Clark, H.K.; El-Gasseir, M.M.; Epp, H.D.K.; Woodford, D.A. [DC Interconnect Inc., Vancouver, BC (Canada); Barthold, L.O.; Reppen, N.D.

    2009-07-01

    There continues to be unprecedented demand on power grids. The primary requirement is for a highly resilient grid that includes large transmission capacity reserves. There is increased demand for total transfer capability (TTC) to meet renewables policy targets and improved accommodation of complex market transactions. Some potential components include storage, FACTS controllers, dynamic ACE and other technologies. This presentation proposed segmentation as a different solution in order to meet the same demands more economically and greatly enhance reliability. The presentation described how segmentation works and discussed the benefits of a simple controller. Segmentation benefits in system planning and operation were also outlined. Other topics that were presented included renewable generation; grid security; cascading; adjustments that an operator might make; line converter and high voltage direct current (HVDC) converter options; HVDC line and converter configurations; and segmentation studies in North America. Economic analyses were also discussed. The presentation concluded with a potential application in northern Europe. 3 figs.

  20. Public–private partnerships value in bioenergy projects: Economic feasibility analysis based on two case studies

    International Nuclear Information System (INIS)

    Fantozzi, Francesco; Bartocci, Pietro; D'Alessandro, Bruno; Arampatzis, Stratos; Manos, Basil

    2014-01-01

    Greece and Italy are facing serious energy challenges concerning sustainability and greenhouse gas emissions as well as security of supply and the competitiveness of the internal energy market. These challenges require investments by the public sector, while the countries have seen in the last years their debts rising. A solution to promote bioenergy business, without rising public debt, could be the use of PPP (Public–Private Partnership). This paper presents a methodology to develop agro-energy business using PPP in two rural areas: the municipality of Evropos (in Greece) and the municipality of Montefalco (in Italy). At first biomass availability is studied, then the optimal technology is selected. Once technological issues have been analyzed PPP value for money has to be assessed. Conventional methods to evaluate economic viability of a project are not enough and a Public-Sector Comparator (PSC) has to be calculated. Typical risks of bioenergy projects are identified, estimating their probabilities and consequences. This will lead to associate a monetary value to each risk. Then the identified risks are allocated among private and public partners, establishing synergies. The allocation of risks will have consequences on the preparation of PPP contract and on partner selection procedure. - Highlights: • PPPs can control or reduce risks in bioenergy business. • Development of a methodology for risk allocation in bioenergy projects. • Development of a methodology for risk valuing in bioenergy projects. • A Public-Sector Comparator has been realized for an agro-energy PPP. • Risk allocation has to be clearly indicated in PPP contract

  1. PWR decontamination feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Silliman, P.L.

    1978-12-18

    The decontamination work which has been accomplished is reviewed and it is concluded that it is worthwhile to investigate further four methods for decontamination for future demonstration. These are: dilute chemical; single stage strong chemical; redox processes; and redox/chemical in combination. Laboratory work is recommended to define the agents and processes for demonstration and to determine the effect of the solvents on PWR materials. The feasibility of Indian Point 1 for decontamination demonstrations is discussed, and it is shown that the system components of Indian Point 1 are well suited for use in demonstrations.

  2. PWR decontamination feasibility study

    International Nuclear Information System (INIS)

    Silliman, P.L.

    1978-01-01

    The decontamination work which has been accomplished is reviewed and it is concluded that it is worthwhile to investigate further four methods for decontamination for future demonstration. These are: dilute chemical; single stage strong chemical; redox processes; and redox/chemical in combination. Laboratory work is recommended to define the agents and processes for demonstration and to determine the effect of the solvents on PWR materials. The feasibility of Indian Point 1 for decontamination demonstrations is discussed, and it is shown that the system components of Indian Point 1 are well suited for use in demonstrations

  3. Feasibility of sensory tongue stimulation combined with task-specific therapy in people with spinal cord injury: a case study.

    Science.gov (United States)

    Chisholm, Amanda E; Malik, Raza Naseem; Blouin, Jean-Sébastien; Borisoff, Jaimie; Forwell, Susan; Lam, Tania

    2014-06-06

    Previous evidence suggests the effects of task-specific therapy can be further enhanced when sensory stimulation is combined with motor practice. Sensory tongue stimulation is thought to facilitate activation of regions in the brain that are important for balance and gait. Improvements in balance and gait have significant implications for functional mobility for people with incomplete spinal cord injury (iSCI). The aim of this case study was to evaluate the feasibility of a lab- and home-based program combining sensory tongue stimulation with balance and gait training on functional outcomes in people with iSCI. Two male participants (S1 and S2) with chronic motor iSCI completed 12 weeks of balance and gait training (3 lab and 2 home based sessions per week) combined with sensory tongue stimulation using the Portable Neuromodulation Stimulator (PoNS). Laboratory based training involved 20 minutes of standing balance with eyes closed and 30 minutes of body-weight support treadmill walking. Home based sessions consisted of balancing with eyes open and walking with parallel bars or a walker for up to 20 minutes each. Subjects continued daily at-home training for an additional 12 weeks as follow-up. Both subjects were able to complete a minimum of 83% of the training sessions. Standing balance with eyes closed increased from 0.2 to 4.0 minutes and 0.0 to 0.2 minutes for S1 and S2, respectively. Balance confidence also improved at follow-up after the home-based program. Over ground walking speed improved by 0.14 m/s for S1 and 0.07 m/s for S2, and skilled walking function improved by 60% and 21% for S1 and S2, respectively. Sensory tongue stimulation combined with task-specific training may be a feasible method for improving balance and gait in people with iSCI. Our findings warrant further controlled studies to determine the added benefits of sensory tongue stimulation to rehabilitation training.

  4. Tribal Utility Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Engel, R. A.; Zoellick, J. J.

    2007-06-30

    The Schatz Energy Research Center (SERC) assisted the Yurok Tribe in investigating the feasibility of creating a permanent energy services program for the Tribe. The original purpose of the DOE grant that funded this project was to determine the feasibility of creating a full-blown Yurok Tribal electric utility to buy and sell electric power and own and maintain all electric power infrastructure on the Reservation. The original project consultant found this opportunity to be infeasible for the Tribe. When SERC took over as project consultant, we took a different approach. We explored opportunities for the Tribe to develop its own renewable energy resources for use on the Reservation and/or off-Reservation sales as a means of generating revenue for the Tribe. We also looked at ways the Tribe can provide energy services to its members and how to fund such efforts. We identified opportunities for the development of renewable energy resources and energy services on the Yurok Reservation that fall into five basic categories: • Demand-side management – This refers to efforts to reduce energy use through energy efficiency and conservation measures. • Off-grid, facility and household scale renewable energy systems – These systems can provide electricity to individual homes and Tribal facilities in areas of the Reservation that do not currently have access to the electric utility grid. • Village scale, micro-grid renewable energy systems - These are larger scale systems that can provide electricity to interconnected groups of homes and Tribal facilities in areas of the Reservation that do not have access to the conventional electric grid. This will require the development of miniature electric grids to serve these interconnected facilities. • Medium to large scale renewable energy development for sale to the grid – In areas where viable renewable energy resources exist and there is access to the conventional electric utility grid, these resources can be

  5. Feasibility study analysis for multi-function dual energy oven (case study: tapioca crackers small medium enterprise)

    Science.gov (United States)

    Soraya, N. W.; El Hadi, R. M.; Chumaidiyah, E.; Tripiawan, W.

    2017-12-01

    Conventional drying process is constrained by weather (cloudy / rainy), and requires wide drying area, and provides low-quality product. Multi-function dual energy oven is the appropriate technology to solve these problems. The oven uses solar thermal or gas heat for drying various type of products, including tapioca crackers. Investment analysis in technical, operational, and financial aspects show that the multi-function dual energy oven is feasible to be implemented for small medium enterprise (SME) processing tapioca crackers.

  6. Digital signature feasibility study

    Science.gov (United States)

    2008-06-01

    The purpose of this study was to assess the advantages and disadvantages of using digital signatures to assist the Arizona Department of Transportation in conducting business. The Department is evaluating the potential of performing more electronic t...

  7. Managing with Learning Disability and Diabetes: OK-Diabetes - a case-finding study and feasibility randomised controlled trial.

    Science.gov (United States)

    House, Allan; Bryant, Louise; Russell, Amy M; Wright-Hughes, Alexandra; Graham, Liz; Walwyn, Rebecca; Wright, Judy M; Hulme, Claire; O'Dwyer, John L; Latchford, Gary; Meer, Shaista; Birtwistle, Jacqueline C; Stansfield, Alison; Ajjan, Ramzi; Farrin, Amanda

    2018-05-01

    Obesity and type 2 diabetes are common in adults with a learning disability. It is not known if the principles of self-management can be applied in this population. To develop and evaluate a case-finding method and undertake an observational study of adults with a learning disability and type 2 diabetes, to develop a standardised supported self-management (SSM) intervention and measure of adherence and to undertake a feasibility randomised controlled trial (RCT) of SSM versus treatment as usual (TAU). Observational study and an individually randomised feasibility RCT. Three cities in West Yorkshire, UK. In the observational study: adults aged > 18 years with a mild or moderate learning disability, who have type 2 diabetes that is not being treated with insulin and who are living in the community. Participants had mental capacity to consent to research and to the intervention. In the RCT participants had glycated haemoglobin (HbA 1c ) levels of > 6.5% (48 mmol/mol), a body mass index (BMI) of > 25 kg/m 2 or self-reported physical activity below national guideline levels. Standardised SSM. TAU supported by an easy-read booklet. (1) The number of eligible participants identified and sources of referral; (2) current living and support arrangements; (3) current health state, including level of HbA 1c , BMI and waist circumference, blood pressure and lipids; (4) mood, preferences for change; (5) recruitment and retention in RCT; (6) implementation and adherence to the intervention; (7) completeness of data collection and values for candidate primary outcomes; and (8) qualitative data on participant experience of the research process and intervention. In the observational study we identified 147 eligible consenting participants. The mean age was 54.4 years. In total, 130 out of 147 (88%) named a key supporter, with 113 supporters (77%) being involved in diabetes management. The mean HbA 1c level was 54.5 mmol/mol [standard deviation (SD) 14.8 mmol/mol; 7

  8. Muon muon collider: Feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-18

    A feasibility study is presented of a 2 + 2 TeV muon collider with a luminosity of L = 10{sup 35} cm{sup {minus}2} s{sup {minus}1}. The resulting design is not optimized for performance, and certainly not for cost; however, it does suffice--the authors believe--to allow them to make a credible case, that a muon collider is a serious possibility for particle physics and, therefore, worthy of R and D support so that the reality of, and interest in, a muon collider can be better assayed. The goal of this support would be to completely assess the physics potential and to evaluate the cost and development of the necessary technology. The muon collider complex consists of components which first produce copious pions, then capture the pions and the resulting muons from their decay; this is followed by an ionization cooling channel to reduce the longitudinal and transverse emittance of the muon beam. The next stage is to accelerate the muons and, finally, inject them into a collider ring which has a small beta function at the colliding point. This is the first attempt at a point design and it will require further study and optimization. Experimental work will be needed to verify the validity of diverse crucial elements in the design.

  9. Muon muon collider: Feasibility study

    International Nuclear Information System (INIS)

    1996-01-01

    A feasibility study is presented of a 2 + 2 TeV muon collider with a luminosity of L = 10 35 cm -2 s -1 . The resulting design is not optimized for performance, and certainly not for cost; however, it does suffice--the authors believe--to allow them to make a credible case, that a muon collider is a serious possibility for particle physics and, therefore, worthy of R and D support so that the reality of, and interest in, a muon collider can be better assayed. The goal of this support would be to completely assess the physics potential and to evaluate the cost and development of the necessary technology. The muon collider complex consists of components which first produce copious pions, then capture the pions and the resulting muons from their decay; this is followed by an ionization cooling channel to reduce the longitudinal and transverse emittance of the muon beam. The next stage is to accelerate the muons and, finally, inject them into a collider ring which has a small beta function at the colliding point. This is the first attempt at a point design and it will require further study and optimization. Experimental work will be needed to verify the validity of diverse crucial elements in the design

  10. Economic feasibility of district heating delivery from industrial excess heat: A case study of a Swedish petrochemical cluster

    International Nuclear Information System (INIS)

    Morandin, Matteo; Hackl, Roman; Harvey, Simon

    2014-01-01

    The present work discusses the potential and the economic feasibility of DH (district heating) delivery using industrial excess heat from a petrochemical cluster at the Swedish West Coast. Pinch Analysis was used for estimating the DH capacity targets and for estimating the cost of heat exchanger installation. A discounted cash flow rate of return of 10% was used as a criterion for identifying the minimum yearly DH delivery that should be guaranteed for a given DH capacity at different DH sales prices. The study was conducted for the current scenario in which no heat recovery is achieved between the cluster plants and for a possible future scenario in which 50% of the fuel currently used for heating purposes is saved by increasing the heat recovery at the site. The competition between excess heat export and local energy efficiency measures is also discussed in terms of CO 2 emission consequences. The maximum capacity of DH delivery amounts today to around 235 MW, which reduces to 110 MW in the future scenario of increased site heat recovery. The results of our analysis show that feasible conditions exist that make DH delivery profitable in the entire capacity range. - Highlights: • Pinch Analysis targeting approach and short-cut cost accounting procedure. • Economic analysis for different DH delivery capacities up to maximum targets. • Sensitivity analysis of heat sales prices. • Parallel plants and cluster wide heat collection systems considered. • Competition between cluster internal heat recovery and excess heat export is discussed

  11. A process for assessing the feasibility of a network meta-analysis: a case study of everolimus in combination with hormonal therapy versus chemotherapy for advanced breast cancer.

    Science.gov (United States)

    Cope, Shannon; Zhang, Jie; Saletan, Stephen; Smiechowski, Brielan; Jansen, Jeroen P; Schmid, Peter

    2014-06-05

    The aim of this study is to outline a general process for assessing the feasibility of performing a valid network meta-analysis (NMA) of randomized controlled trials (RCTs) to synthesize direct and indirect evidence for alternative treatments for a specific disease population. Several steps to assess the feasibility of an NMA are proposed based on existing recommendations. Next, a case study is used to illustrate this NMA feasibility assessment process in order to compare everolimus in combination with hormonal therapy to alternative chemotherapies in terms of progression-free survival for women with advanced breast cancer. A general process for assessing the feasibility of an NMA is outlined that incorporates explicit steps to visualize the heterogeneity in terms of treatment and outcome characteristics (Part A) as well as the study and patient characteristics (Part B). Additionally, steps are performed to illustrate differences within and across different types of direct comparisons in terms of baseline risk (Part C) and observed treatment effects (Part D) since there is a risk that the treatment effect modifiers identified may not explain the observed heterogeneity or inconsistency in the results due to unexpected, unreported or unmeasured differences. Depending on the data available, alternative approaches are suggested: list assumptions, perform a meta-regression analysis, subgroup analysis, sensitivity analyses, or summarize why an NMA is not feasible. The process outlined to assess the feasibility of an NMA provides a stepwise framework that will help to ensure that the underlying assumptions are systematically explored and that the risks (and benefits) of pooling and indirectly comparing treatment effects from RCTs for a particular research question are transparent.

  12. Non-invasive, home-based electroencephalography hypoglycaemia warning system for personal monitoring using skin surface electrodes: a single-case feasibility study.

    Science.gov (United States)

    Clewett, Christopher J; Langley, Phillip; Bateson, Anthony D; Asghar, Aziz; Wilkinson, Antony J

    2016-03-01

    Hypoglycaemia unawareness is a common condition associated with increased risk of severe hypoglycaemia. The purpose of the authors' study was to develop a simple to use, home-based and non-invasive hypoglycaemia warning system based on electroencephalography (EEG), and to demonstrate its use in a single-case feasibility study. A participant with type 1 diabetes forms a single-person case study where blood sugar levels and EEG were recorded. EEG was recorded using skin surface electrodes placed behind the ear located within the T3 region by the participant in the home. EEG was analysed retrospectively to develop an algorithm which would trigger a warning if EEG changes associated with hypoglycaemia onset were detected. All hypoglycaemia events were detected by the EEG hypoglycaemia warning algorithm. Warnings were triggered with blood glucose concentration levels at or below 4.2 mmol/l in this participant and no warnings were issued when in euglycaemia. The feasibility of a non-invasive EEG-based hypoglycaemia warning system for personal monitoring in the home has been demonstrated in a single case study. The results suggest that further studies are warranted to evaluate the system prospectively in a larger group of participants.

  13. Dual-Doppler Feasibility Study

    Science.gov (United States)

    Huddleston, Lisa L.

    2012-01-01

    When two or more Doppler weather radar systems are monitoring the same region, the Doppler velocities can be combined to form a three-dimensional (3-D) wind vector field thus providing for a more intuitive analysis of the wind field. A real-time display of the 3-D winds can assist forecasters in predicting the onset of convection and severe weather. The data can also be used to initialize local numerical weather prediction models. Two operational Doppler Radar systems are in the vicinity of Kennedy Space Center (KSC) and Cape Canaveral Air Force Station (CCAFS); these systems are operated by the 45th Space Wing (45 SW) and the National Weather Service Melbourne, Fla. (NWS MLB). Dual-Doppler applications were considered by the 45 SW in choosing the site for the new radar. Accordingly, the 45th Weather Squadron (45 WS), NWS MLB and the National Aeronautics and Space Administration tasked the Applied Meteorology Unit (AMU) to investigate the feasibility of establishing dual-Doppler capability using the two existing systems. This study investigated technical, hardware, and software requirements necessary to enable the establishment of a dual-Doppler capability. Review of the available literature pertaining to the dual-Doppler technique and consultation with experts revealed that the physical locations and resulting beam crossing angles of the 45 SW and NWS MLB radars make them ideally suited for a dual-Doppler capability. The dual-Doppler equations were derived to facilitate complete understanding of dual-Doppler synthesis; to determine the technical information requirements; and to determine the components of wind velocity from the equation of continuity and radial velocity data collected by the two Doppler radars. Analysis confirmed the suitability of the existing systems to provide the desired capability. In addition, it is possible that both 45 SW radar data and Terminal Doppler Weather Radar data from Orlando International Airport could be used to alleviate any

  14. A feasibility assessment of calculation procedure with case study and the modification of dose conversion factor in STARDOSE

    International Nuclear Information System (INIS)

    Ko, H. S.; Jang, M.; Kim, S. H.; Kang, C. S.

    2003-01-01

    STARDOSE computer code is the designed code for which is calculated the dose of control room and off-site dose on design basis accident of nuclear power plant. Input files of STARDOSE are libfile1.txt which has decay constant and dose conversion factor, and input.dat which structurally expresses the real plant model by editor. It is given much advanced result with using newer dose conversion factor in libfile1.txt. In this study, therefore, case study is performed that is made input.dat file for LOCA and libfile1.txt which is included newer dose conversion factor and core inventory on APR-1400 and UCN 5 and 6. The result of case study is compared and analyzed

  15. DPC loading feasibility study report

    International Nuclear Information System (INIS)

    Dafoe, R.E.; Lopez, D.A.; Williams, K.L.

    1997-11-01

    Disposal of radioactive wastes now stored at the Idaho Chemical Processing Plant at the Idaho National Engineering and Environmental Laboratory is mandated under a ''Settlement Agreement'' between the Department of Energy and the State of Idaho. This study investigates the feasibility of using the Dry Transfer Cell facility to package waste into Dual Purpose Canisters for interim storage at the adjacent Dry Storage System comprised of an interim storage pad with NUHOMS reg-sign storage modules. The wastes would then be road-ready for eventual disposal in a permanent repository. The operating period for these activities is expected to be from 2015 to 2035

  16. An investigation on technical feasibilities of fuel cycle for high temperature gas-cooled reactor (Case study)

    International Nuclear Information System (INIS)

    Sumita, Junya; Ueta, Shohei; Aihara, Jun; Shibata, Taiju; Sawa, Kazuhiro

    2008-03-01

    In accordance with the basic policy of effectively using nuclear fuel resources, the FBR cycle, one of the most possible fuel cycle in the future, will be adapted after plu-thermal program by LWR in Japanese nuclear cycle plan. In this paper, a case study of technical investigation of HTGR fuel cycle based on HTGR fuel cycle proposed to adapt to Japanese nuclear fuel cycle plan were carried out from the viewpoint of effective utilization of uranium, fabrication technologies of MOX fuel, reprocessing technologies, amount of interim storage of HTGR fuel and graphite waste. As a result, the fuel cycle for HTGR is expected to be possible technically. (author)

  17. PV solar system feasibility study

    International Nuclear Information System (INIS)

    Ashhab, Moh’d Sami S.; Kaylani, Hazem; Abdallah, Abdallah

    2013-01-01

    Highlights: ► This research studies the feasibility of PV solar systems. ► The aim is to develop the theory and application of a hybrid system. ► Relevant research topics are reviewed and some of them are discussed in details. ► A prototype of the PV solar system is designed and built. - Abstract: This research studies the feasibility of PV solar systems and aims at developing the theory and application of a hybrid system that utilizes PV solar system and another supporting source of energy to provide affordable heating and air conditioning. Relevant research topics are reviewed and some of them are discussed in details. Solar heating and air conditioning research and technology exist in many developed countries. To date, the used solar energy has been proved to be inefficient. Solar energy is an abundant source of energy in Jordan and the Middle East; with increasing prices of oil this source is becoming more attractive alternative. A good candidate for the other system is absorption. The overall system is designed such that it utilizes solar energy as a main source. When the solar energy becomes insufficient, electricity or diesel source kicks in. A prototype of the PV solar system that operates an air conditioning unit is built and proper measurements are collected through a data logging system. The measured data are plotted and discussed, and conclusions regarding the system performance are extracted.

  18. Combining Mental Training and Physical Training With Goal-Oriented Protocols in Stroke Rehabilitation: A Feasibility Case Study

    Directory of Open Access Journals (Sweden)

    Xin Zhang

    2018-04-01

    Full Text Available Stroke is one of the leading causes of permanent disability in adults. The literature suggests that rehabilitation is key to early motor recovery. However, conventional therapy is labor and cost intensive. Robotic and functional electrical stimulation (FES devices can provide a high dose of repetitions and as such may provide an alternative, or an adjunct, to conventional rehabilitation therapy. Brain-computer interfaces (BCI could augment neuroplasticity by introducing mental training. However, mental training alone is not enough; but combining mental with physical training could boost outcomes. In the current case study, a portable rehabilitative platform and goal-oriented supporting training protocols were introduced and tested with a chronic stroke participant. A novel training method was introduced with the proposed rehabilitative platform. A 37-year old individual with chronic stroke participated in 6-weeks of training (18 sessions in total, 3 sessions a week, and 1 h per session. In this case study, we show that an individual with chronic stroke can tolerate a 6-week training bout with our system and protocol. The participant was actively engaged throughout the training. Changes in the Wolf Motor Function Test (WMFT suggest that the training positively affected arm motor function (12% improvement in WMFT score.

  19. Feasibility study on the import of fresh organic coconut from Nigeria to Germany : a case study of BioTropic import company, Germany

    NARCIS (Netherlands)

    Bashirat, O.O.

    2012-01-01

    This study focuses on the economic feasibility of fresh organic coconut in Nigeria and other important factors such as quality, volume, logistic and standard that is involved in the supply of one container fresh organic coconut from Nigeria to Germany on monthly basis. BioTropic is an import company

  20. IPNS upgrade: A feasibility study

    International Nuclear Information System (INIS)

    1995-04-01

    Many of Argonne National Laboratory's (ANL's) scientific staff members were very active in R ampersand D work related to accelerator-based spoliation sources in the 1970s and early 1980s. In 1984, the Seitz/Eastman Panel of the National Academy of Sciences reviewed U.S. materials science research facilities. One of the recommendations of this panel was that the United States build a reactor-based steady-state source, the Advanced Neutron Source (ANS), at Oak Ridge National Laboratory. Subsequently, R ampersand D activities related to the design of an accelerator-based source assumed a lower priority. The resumption of pulsed-source studies in this country started simultaneously with design activities in Europe aimed at the European Spallation Source (ESS). The European Community funded a workshop in September 1991 to define the parameters of the ESS. Participants in this workshop included both accelerator builders and neutron source users. A consortium of European countries has proposed to build a 5-MW pulsed source, and a feasibility study is currently under way. Soon after the birth of the ESS, a small group at ANL set about bringing themselves up to date on pulsed-source information since 1984 and studied the feasibility of upgrading ANL's Intense Pulsed Neutron Source (IPNS) to 1 MW by means of a rapidly cycling synchrotron that could be housed, along with its support facilities, in existing buildings. In early 1993, the Kohn panel recommended that (1) design and construction of the ANS should be completed according to the proposed project schedule and (2) development of competitive proposals for cost-effective design and construction of a 1-MW pulsed spallation source should be authorized immediately

  1. IPNS upgrade: A feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-01

    Many of Argonne National Laboratory`s (ANL`s) scientific staff members were very active in R&D work related to accelerator-based spoliation sources in the 1970s and early 1980s. In 1984, the Seitz/Eastman Panel of the National Academy of Sciences reviewed U.S. materials science research facilities. One of the recommendations of this panel was that the United States build a reactor-based steady-state source, the Advanced Neutron Source (ANS), at Oak Ridge National Laboratory. Subsequently, R&D activities related to the design of an accelerator-based source assumed a lower priority. The resumption of pulsed-source studies in this country started simultaneously with design activities in Europe aimed at the European Spallation Source (ESS). The European Community funded a workshop in September 1991 to define the parameters of the ESS. Participants in this workshop included both accelerator builders and neutron source users. A consortium of European countries has proposed to build a 5-MW pulsed source, and a feasibility study is currently under way. Soon after the birth of the ESS, a small group at ANL set about bringing themselves up to date on pulsed-source information since 1984 and studied the feasibility of upgrading ANL`s Intense Pulsed Neutron Source (IPNS) to 1 MW by means of a rapidly cycling synchrotron that could be housed, along with its support facilities, in existing buildings. In early 1993, the Kohn panel recommended that (1) design and construction of the ANS should be completed according to the proposed project schedule and (2) development of competitive proposals for cost-effective design and construction of a 1-MW pulsed spallation source should be authorized immediately.

  2. A Framework for Statewide Analysis of Site Suitability, Energy Estimation, Life Cycle Costs, Financial Feasibility and Environmental Assessment of Wind Farms: A Case Study of Indiana

    Science.gov (United States)

    Kumar, Indraneel

    In the last decade, Midwestern states including Indiana have experienced an unprecedented growth in utility scale wind energy farms. For example, by end of 2013, Indiana had 1.5 GW of wind turbines installed, which could provide electrical energy for as many as half-a-million homes. However, there is no statewide systematic framework available for the evaluation of wind farm impacts on endangered species, required necessary setbacks and proximity standards to infrastructure, and life cycle costs. This research is guided to fill that gap and it addresses the following questions. How much land is suitable for wind farm siting in Indiana given the constraints of environmental, ecological, cultural, settlement, physical infrastructure and wind resource parameters? How much wind energy can be obtained? What are the life cycle costs and economic and financial feasibility? Is wind energy production and development in a state an emission free undertaking? The framework developed in the study is applied to a case study of Indiana. A fuzzy logic based AHP (Analytic Hierarchy Process) spatial site suitability analysis for wind energy is formulated. The magnitude of wind energy that could be sited and installed comprises input for economic and financial feasibility analysis for 20-25 years life cycle of wind turbines in Indiana. Monte Carlo simulation is used to account for uncertainty and nonlinearity in various costs and price parameters. Impacts of incentives and cost variables such as production tax credits, costs of capital, and economies of scale are assessed. Further, an economic input-output (IO) based environmental assessment model is developed for wind energy, where costs from financial feasibility analysis constitute the final demand vectors. This customized model for Indiana is used to assess emissions for criteria air pollutants, hazardous air pollutants and greenhouse gases (GHG) across life cycle events of wind turbines. The findings of the case study include

  3. Muon Muon Collider: Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Gallardo, J.C.; Palmer, R.B.; /Brookhaven; Tollestrup, A.V.; /Fermilab; Sessler, A.M.; /LBL, Berkeley; Skrinsky, A.N.; /Novosibirsk, IYF; Ankenbrandt, C.; Geer, S.; Griffin, J.; Johnstone, C.; Lebrun, P.; McInturff, A.; Mills, Frederick E.; Mokhov, N.; Moretti, A.; Neuffer, D.; Ng, K.Y.; Noble, R.; Novitski, I.; Popovic, M.; Qian, C.; Van Ginneken, A. /Fermilab /Brookhaven /Wisconsin U., Madison /Tel Aviv U. /Indiana U. /UCLA /LBL, Berkeley /SLAC /Argonne /Sobolev IM, Novosibirsk /UC, Davis /Munich, Tech. U. /Virginia U. /KEK, Tsukuba /DESY /Novosibirsk, IYF /Jefferson Lab /Mississippi U. /SUNY, Stony Brook /MIT /Columbia U. /Fairfield U. /UC, Berkeley

    2012-04-05

    A feasibility study is presented of a 2 + 2 TeV muon collider with a luminosity of L = 10{sup 35} cm{sup -2}s{sup -1}. The resulting design is not optimized for performance, and certainly not for cost; however, it does suffice - we believe - to allow us to make a credible case, that a muon collider is a serious possibility for particle physics and, therefore, worthy of R and D support so that the reality of, and interest in, a muon collider can be better assayed. The goal of this support would be to completely assess the physics potential and to evaluate the cost and development of the necessary technology. The muon collider complex consists of components which first produce copious pions, then capture the pions and the resulting muons from their decay; this is followed by an ionization cooling channel to reduce the longitudinal and transverse emittance of the muon beam. The next stage is to accelerate the muons and, finally, inject them into a collider ring wich has a small beta function at the colliding point. This is the first attempt at a point design and it will require further study and optimization. Experimental work will be needed to verify the validity of diverse crucial elements in the design. Muons because of their large mass compared to an electron, do not produce significant synchrotron radiation. As a result there is negligible beamstrahlung and high energy collisions are not limited by this phenomena. In addition, muons can be accelerated in circular devices which will be considerably smaller than two full-energy linacs as required in an e{sup +} - e{sup -} collider. A hadron collider would require a CM energy 5 to 10 times higher than 4 TeV to have an equivalent energy reach. Since the accelerator size is limited by the strength of bending magnets, the hadron collider for the same physics reach would have to be much larger than the muon collider. In addition, muon collisions should be cleaner than hadron collisions. There are many detailed particle

  4. Trialling diagnosis-related groups classification in the Iranian health system: a case study examining the feasibility of introducing casemix.

    Science.gov (United States)

    Ghaffari, S; Doran, C; Wilson, A; Aisbett, C

    2010-05-01

    This paper examines the quality of routinely collected information in an Iranian hospital in a trial of casemix classification. Australian Refined Diagnosis Related Groups (AR-DRG) were used to classify patient episodes. There were 327 DRGs identified, of which 20% had only 1 case. The grouper program identified invalid records for 4% of total separations. Approximately 4.5% of cases were classified into error DRGs and 3.4% were ungroupable. No complication and comorbidity effects were identified with 93% of total cases. R2 (variance in length of stay explained) was 44% for untrimmed cases, increasing to 63%, 57% and 58% after trimming by L3H3, IQR and 10th-95th percentile methods respectively.

  5. MRS transfer facility feasibility study

    International Nuclear Information System (INIS)

    Jowdy, A.K.; Smith, R.I.

    1990-12-01

    Under contract to the US Department of Energy, Parsons was requested to evaluate the feasibility of building a simple hot cell (waste handling) transfer facility at the Monitored Retrievable Storage (MRS) site to facilitate acceptance of spent fuel into the Federal Waste Management System starting in early 1998. The Transfer Facility was intended to provide a receiving and transfer to storage capability at a relatively low throughput rate (approximately 500 MTU/yr) and to provide the recovery capability needed on the site in the event of a transport or storage cask seal failure during a period of about two years while the larger Spent Fuel Handling Building (SFHB) was being completed. Although the original study basis postulated an incremental addition to the larger, previously considered MRS configurations, study results show that the Transfer Facility may be capable of receiving and storing spent fuel at annual rates of 3000 MTU/yr or more, making a larger fuel handling structure unnecessary. In addition, the study analyses showed that the Transfer Facility could be constructed and put into service in 15--17 months and would cost less than the previous configurations. 2 figs., 2 tabs

  6. Full system decontamination feasibility studies

    International Nuclear Information System (INIS)

    Denault, R.P.; LeSurf, J.E.; Walschot, F.W.

    1988-01-01

    Many chemical decontaminations have been performed on subsystems in light water reactors (BWRs and PWRs) but none on the full system (including the fuel) of large, (>500 MWe) investor owned reactors. Full system decontaminations on pressure-tubed reactors have been shown to facilitate maintenance, inspection, repair and replacement of reactor components. Further advantages are increased reactor availability and plant life extension. A conceptual study has been performed for EPRI (for PWRs) and Commonwealth Edison Co (for BWRs) into the applicability and cost benefit of full system decontaminations (FSD). The joint study showed that FSDs in both PWRs and BWRs, with or without the fuel included in the decontamination, are feasible and cost beneficial provided a large amount of work is to be done following the decontamination. The large amounts of radioactive waste generated can be managed using current technologies. Considerable improvements in waste handling, and consequent cost savings, can be obtained if new techniques which are now reaching commercial application are used. (author)

  7. Clinical feasibility of brain-computer interface based on steady-state visual evoked potential in patients with locked-in syndrome: Case studies.

    Science.gov (United States)

    Hwang, Han-Jeong; Han, Chang-Hee; Lim, Jeong-Hwan; Kim, Yong-Wook; Choi, Soo-In; An, Kwang-Ok; Lee, Jun-Hak; Cha, Ho-Seung; Hyun Kim, Seung; Im, Chang-Hwan

    2017-03-01

    Although the feasibility of brain-computer interface (BCI) systems based on steady-state visual evoked potential (SSVEP) has been extensively investigated, only a few studies have evaluated its clinical feasibility in patients with locked-in syndrome (LIS), who are the main targets of BCI technology. The main objective of this case report was to share our experiences of SSVEP-based BCI experiments involving five patients with LIS, thereby providing researchers with useful information that can potentially help them to design BCI experiments for patients with LIS. In our experiments, a four-class online SSVEP-based BCI system was implemented and applied to four of five patients repeatedly on multiple days to investigate its test-retest reliability. In the last experiments with two of the four patients, the practical usability of our BCI system was tested using a questionnaire survey. All five patients showed clear and distinct SSVEP responses at all four fundamental stimulation frequencies (6, 6.66, 7.5, 10 Hz), and responses at harmonic frequencies were also observed in three patients. Mean classification accuracy was 76.99% (chance level = 25%). The test-retest reliability experiments demonstrated stable performance of our BCI system over different days even when the initial experimental settings (e.g., electrode configuration, fixation time, visual angle) used in the first experiment were used without significant modifications. Our results suggest that SSVEP-based BCI paradigms might be successfully used to implement clinically feasible BCI systems for severely paralyzed patients. © 2016 Society for Psychophysiological Research.

  8. Feasibility study for the partial conversion of a hydropower plant into a pumped-storage power plant: a case study of hydroelectric power plant La Barca (Asturias, Spain

    Directory of Open Access Journals (Sweden)

    E. Antuña Yudego

    2017-01-01

    Full Text Available Renewable energy sources have reported an unprecedented increase of global installed renewable power capacity. Against the advantages provided by this renewable power generation technology it should be taken into account an important issue: these intermittent energy sources supply a fluctuating output which is difficult to manage. Pumped-storage hydro power plants reappear in these circumstances as an efficient form of energy storage which allows to use reserves when necessary, enabling power generation output to cover continuously this energy demand. The present paper shows a simplified feasibility study of the partial conversion of hydropower plant La Barca, in Asturias, into a reversible storage through the development of an algorithm to simulate its operation according to electricity market prices. For this purpose, the operation in the deviation management market is considered and the technical modifications required for the conversion are shown. The estimation of costs and incomes present a feasible scenario.

  9. The acceptability, feasibility and impact of a lay health counsellor delivered health promoting schools programme in India: a case study evaluation

    Directory of Open Access Journals (Sweden)

    Rajaraman Divya

    2012-05-01

    Full Text Available Abstract Background Studies in resource-limited settings have shown that there are constraints to the use of teachers, peers or health professionals to deliver school health promotion interventions. School health programmes delivered by trained lay health counsellors could offer a cost-effective alternative. This paper presents a case study of a multi-component school health promotion intervention in India that was delivered by lay school health counsellors, who possessed neither formal educational nor health provider qualifications. Methods The intervention was based on the WHO’s Health Promoting Schools framework, and included health screening camps; an anonymous letter box for student questions and complaints; classroom-based life skills training; and, individual psycho-social and academic counselling for students. The intervention was delivered by a lay school health counsellor who had attained a minimum of a high school education. The counsellor was trained over four weeks and received structured supervision from health professionals working for the implementing NGO. The evaluation design was a mixed methods case study. Quantitative process indicators were collected to assess the extent to which the programme was delivered as planned (feasibility, the uptake of services (acceptability, and the number of students who received corrective health treatment (evidence of impact. Semi-structured interviews were conducted over two years with 108 stakeholders, and were analysed to identify barriers and facilitators for the programme (feasibility, evaluate acceptability, and gather evidence of positive or negative effects of the programme. Results Feasibility was established by the high reported coverage of all the targeted activities by the school health counsellor. Acceptability was indicated by a growing number of submissions to the students’ anonymous letter-box; more students self-referring for counselling services over time; and, the

  10. The acceptability, feasibility and impact of a lay health counsellor delivered health promoting schools programme in India: a case study evaluation.

    Science.gov (United States)

    Rajaraman, Divya; Travasso, Sandra; Chatterjee, Achira; Bhat, Bhargav; Andrew, Gracy; Parab, Suraj; Patel, Vikram

    2012-05-25

    Studies in resource-limited settings have shown that there are constraints to the use of teachers, peers or health professionals to deliver school health promotion interventions. School health programmes delivered by trained lay health counsellors could offer a cost-effective alternative. This paper presents a case study of a multi-component school health promotion intervention in India that was delivered by lay school health counsellors, who possessed neither formal educational nor health provider qualifications. The intervention was based on the WHO's Health Promoting Schools framework, and included health screening camps; an anonymous letter box for student questions and complaints; classroom-based life skills training; and, individual psycho-social and academic counselling for students. The intervention was delivered by a lay school health counsellor who had attained a minimum of a high school education. The counsellor was trained over four weeks and received structured supervision from health professionals working for the implementing NGO. The evaluation design was a mixed methods case study. Quantitative process indicators were collected to assess the extent to which the programme was delivered as planned (feasibility), the uptake of services (acceptability), and the number of students who received corrective health treatment (evidence of impact). Semi-structured interviews were conducted over two years with 108 stakeholders, and were analysed to identify barriers and facilitators for the programme (feasibility), evaluate acceptability, and gather evidence of positive or negative effects of the programme. Feasibility was established by the high reported coverage of all the targeted activities by the school health counsellor. Acceptability was indicated by a growing number of submissions to the students' anonymous letter-box; more students self-referring for counselling services over time; and, the perceived need for the programme, as expressed by principals

  11. Feasibility Study on HYSOL CSP

    DEFF Research Database (Denmark)

    Nielsen, Lars Henrik; Baldini, Mattia; Skytte, Klaus

    2016-01-01

    integrated HYSOL concept, therefore, becomes a fully dispatchable (offering firm power) and fully renewable energy source (RES) based power supply alternative, offering CO2-free electricity in regions with sufficient solar resources. The economic feasibility of HYSOL configurations is addressed in this paper....... The CO2 free HYSOL alternative is discussed relative to conventional reference firm power generation technologies. In particular the HYSOL performance relative to new power plants based on natural gas (NG) such as open cycle or combined cycle gas turbines (OCGT or CCGT) are in focus. The feasibility...

  12. Feasibility of assessing the public health impacts of air pollution reduction programs on a local scale: New Haven accountability case study

    Science.gov (United States)

    Background: New approaches on how to link health surveillance data with environmental and population exposure information are needed in order to examine the health benefits of risk management decisions. Objective: This study's objective was to examine the feasibility of conductin...

  13. Multnomah County Hydrokinetic Feasibility Study: Final Feasibility Study Report

    Energy Technology Data Exchange (ETDEWEB)

    Spain, Stephen

    2012-03-15

    HDR has completed a study of the technical, regulatory, and economic feasibility of installing hydrokinetic turbines under the Morrison, Broadway, and Sellwood bridges. The primary objective of installing hydrokinetic turbines is a demonstration of in-stream hydrokinetic technologies for public education and outreach. Due to the low gradient of the Lower Willamette and the effects of the tide, velocities in the area in consideration are simply not high enough to economically support a commercial installation. While the velocities in the river may at times provide enough energy for a commercial turbine to reach capacity, the frequency and duration of high flow events which provide suitable velocities is not sufficient to support a commercial hydrokinetic installation. We have observed that over an 11 year period, daily average velocities in the Lower Willamette exceeded a nominal cut-in speed of 0.75 m/s only 20% of the time, leaving net zero power production for the remaining 80% of days. The Sellwood Bridge site was estimated to have the best hydrokinetic resource, with an estimated average annual production of about 9,000 kWh. The estimated production could range from 2,500 kWh to 15,000 kWh. Based on these energy estimates, the amount of revenue generated through either a power purchase agreement (PPA) or recovered through net metering is not sufficient to repay the project costs within the life of the turbine. The hydrokinetic resource at the Morrison and Broadway Bridges is slightly smaller than at the Sellwood Bridge. While the Broadway and Morrison Bridges have existing infrastructure that could be utilized, the project is not expected to generate enough revenue to repay the investment. Despite low velocities and energy production, the sites themselves are favorable for installation of a demonstration or experimental project. With high public interest in renewable energy, the possibility exists to develop a hydrokinetic test site which could provide

  14. Pre-feasibility study on the investment in a new SPA & wellness facility : Case Study: based on a hotel-restaurant in Germany

    OpenAIRE

    Jahn, Moritz

    2011-01-01

    The object of investigation has at the present a wellness facility which is however out-dated and does not longer support the general appearance. Therefore, a new investment has to be done which will be assessed with regard to its conceptual, economic and financial viability. In particular, the economic and financial viability of the new SPA & wellness facility by itself had to be assessed, as this is the main criteria for the principal. The extent of the pre-feasibility study is a limited ve...

  15. WERF MACT Feasibility Study Report

    Energy Technology Data Exchange (ETDEWEB)

    B. Bonnema; D. Moser; J. Riedesel; K. Kooda; K. Liekhus; K. Rebish; S. Poling

    1998-11-01

    This study was undertaken to determine the technical feasibility of upgrading the Waste Experimental Reduction Facility (WERF) at the Idaho National Engineering and Environmental Laboratory to meet the offgas emission limits proposed in the Maximum Achievable Control Technologies (MACT)rule. Four practicable offgas treatment processes were identified, which, if installed, would enable the WERF to meet the anticipated MACT emission limits for dioxins and furans (D/F), hydrochloric acid (HCI), and mercury (Hg). Due to the three-year time restraint for MACT compliance, any technology chosen for the upgrade must be performed within the general plant project funding limit of $5 M. The option selected consists of a partial-quench evaporative cooler with dry sorbent injection for HCI removal followed by a sulfur-impregnated activated carbon bed for Hg control. The planning cost estimate for implementing the option is $4.17 M (with 24% contingency). The total estimated cost includes capital costs, design and construction costs, and project management costs. Capital costs include the purchase of a new offgas evaporative cooler, a dry sorbent injection system with reagent storage, a new fabric filter baghouse, a fixed carbon bed absorber, and two offgas induced draft exhaust fans. It is estimated that 21 months will be required to complete the recommended modification to the WERF. The partial-quench cooler is designed to rapidly cool the offgas exiting the secondary combustion chamber to minimize D/F formation. Dry sorbent injection of an alkali reagent into the offgas is recommended. The alkali reacts with the HCI to form a salt, which is captured with the fly ash in the baghouse. A design HCI removal efficiency of 97.2% allows for the feeding 20 lbs/hr of chlorine to the WERF incinerator. The sorbent feed rate can be adjusted to achieve the desired HCI removal efficiency. A fixed bed of sulfur-impregnated carbon was conservatively sized for a total Hg removal capacity when

  16. Visualizing feasible operating ranges within tissue engineering systems using a "windows of operation" approach: a perfusion-scaffold bioreactor case study.

    Science.gov (United States)

    McCoy, Ryan J; O'Brien, Fergal J

    2012-12-01

    Tissue engineering approaches to developing functional substitutes are often highly complex, multivariate systems where many aspects of the biomaterials, bio-regulatory factors or cell sources may be controlled in an effort to enhance tissue formation. Furthermore, success is based on multiple performance criteria reflecting both the quantity and quality of the tissue produced. Managing the trade-offs between different performance criteria is a challenge. A "windows of operation" tool that graphically represents feasible operating spaces to achieve user-defined levels of performance has previously been described by researchers in the bio-processing industry. This paper demonstrates the value of "windows of operation" to the tissue engineering field using a perfusion-scaffold bioreactor system as a case study. In our laboratory, perfusion bioreactor systems are utilized in the context of bone tissue engineering to enhance the osteogenic differentiation of cell-seeded scaffolds. A key challenge of such perfusion bioreactor systems is to maximize the induction of osteogenesis but minimize cell detachment from the scaffold. Two key operating variables that influence these performance criteria are the mean scaffold pore size and flow-rate. Using cyclooxygenase-2 and osteopontin gene expression levels as surrogate indicators of osteogenesis, we employed the "windows of operation" methodology to rapidly identify feasible operating ranges for the mean scaffold pore size and flow-rate that achieved user-defined levels of performance for cell detachment and differentiation. Incorporation of such tools into the tissue engineer's armory will hopefully yield a greater understanding of the highly complex systems used and help aid decision making in future translation of products from the bench top to the market place. Copyright © 2012 Wiley Periodicals, Inc.

  17. Sault Tribe Wind Energy Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Toni Osterhout; Global Energy Concepts

    2005-07-31

    The Sault Tribe conducted a feasibility study on tribal lands in the Upper Peninsula of Michigan to determine the technical and economic feasibility of both small and large-scale wind power development on tribal lands. The study included a wind resource assessment, transmission system analysis, engineering and regulatory analyzes and assessments.

  18. On the feasibility of using emergy analysis as a source of benchmarking criteria through data envelopment analysis: A case study for wind energy

    International Nuclear Information System (INIS)

    Iribarren, Diego; Vázquez-Rowe, Ian; Rugani, Benedetto; Benetto, Enrico

    2014-01-01

    The definition of criteria for the benchmarking of similar entities is often a critical issue in analytical studies because of the multiplicity of criteria susceptible to be taken into account. This issue can be aggravated by the need to handle multiple data for multiple facilities. This article presents a methodological framework, named the Em + DEA method, which combines emergy analysis with Data Envelopment Analysis (DEA) for the ecocentric benchmarking of multiple resembling entities (i.e., multiple decision making units or DMUs). Provided that the life-cycle inventories of these DMUs are available, an emergy analysis is performed through the computation of seven different indicators, which refer to the use of fossil, metal, mineral, nuclear, renewable energy, water and land resources. These independent emergy values are then implemented as inputs for DEA computation, thus providing operational emergy-based efficiency scores and, for the inefficient DMUs, target emergy flows (i.e., feasible emergy benchmarks that would turn inefficient DMUs into efficient). The use of the Em + DEA method is exemplified through a case study of wind energy farms. The potential use of CED (cumulative energy demand) and CExD (cumulative exergy demand) indicators as alternative benchmarking criteria to emergy is discussed. The combined use of emergy analysis with DEA is proven to be a valid methodological approach to provide benchmarks oriented towards the optimisation of the life-cycle performance of a set of multiple similar facilities, not being limited to the operational traits of the assessed units. - Highlights: • Combined emergy and DEA method to benchmark multiple resembling entities. • Life-cycle inventory, emergy analysis and DEA as key steps of the Em + DEA method. • Valid ecocentric benchmarking approach proven through a case study of wind farms. • Comparison with life-cycle energy-based benchmarking criteria (CED/CExD + DEA). • Analysts and decision and policy

  19. Feasibility Study on HYSOL CSP

    DEFF Research Database (Denmark)

    Nielsen, Lars Henrik; Skytte, Klaus; Pérez, Cristian Hernán Cabrera

    2016-01-01

    Concentrating Solar Power (CSP) plants utilize thermal conversion of direct solar irradiation. A trough or tower configuration focuses solar radiation and heats up oil or molten salt that subsequently in high temperature heat exchangers generate steam for power generation. High temperature molten...... salt can be stored and the stored heat can thus increase the load factor and the usability for a CSP plant, e.g. to cover evening peak demand. In the HYSOL concept (HYbrid SOLar) such configuration is extended further to include a gas turbine fuelled by upgraded biogas or natural gas. The optimised...... integrated HYSOL concept, therefore, becomes a fully dispatchable (offering firm power) and fully renewable energy source (RES) based power supply alternative, offering CO2-free electricity in regions with sufficient solar resources. The economic feasibility of HYSOL configurations is addressed in this paper...

  20. Kalundborg case study, a feasibility study of CO{sub 2} storage in onshore saline aquifers. CO2STORE[Denmark

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Michael; Bech, N.; Bidstrup, T.; Christensen, Niels Peter; Vangkilde-Pedersen, T. [GEUS (Denmark); Biede, O. [ENERGI E2 (Denmark)

    2007-06-15

    The Danish case-study of the CO2STORE project comprises the potential future capture and underground storage of CO{sub 2} from two point sources. These are the coal fired power plant Asnaesvaerket and the Statoil refinery both located in the city of Kalundborg, Denmark. Initial mapping of the storage structure was conducted as part of the EU funded research project GESTCO that was concluded in 2003. The study identified a large underground structure forming a potential, future storage site 15 km to the northeast of the city. Porous sandstones filled with saline water at a depth of approximately 1.500 m form the reservoir. The structure covers approximately 160 km{sup 2} and a preliminary calculation suggests a storage capacity of nearly 900 million tonnes of CO2 equal to more than 150 years of CO{sub 2} emissions from the two point sources. In the Kalundborg case-study, a fictive capture and storage scenario will be formulated and modelled. The scenario is based on experiences learned through the SACS and GESTCO projects. Detailed geological modelling, reservoir simulation, reservoir and cap rock characterisation and risk assessment will be important issues for the case-study. The Geological Survey of Denmark and Greenland (GEUS) is project leader for the Kalundborg case-study. Information on CO{sub 2} emissions from the point sources and technical and economical input for the three scenarios is provided by the industrial partners; ENERGI E2 and Statoil ASA. The scenario is designed only for this case study and does not reflect the strategic plans of ENERGI E2 nor Statoil ASA. Geochemical simulation and modelling studies on reservoir and cap rock were performed at Bureau de Recherches Geologiques et Minieres (BRGM) in France. The CO2STORE project is performed within the European Community supported 5th Framework Programme. (au)

  1. When preparation meets opportunity: a case study exploring the feasibility of pursuing a career in biology for two Latina high school girls

    Science.gov (United States)

    García, Yeni Violeta

    2013-12-01

    The future of this country depends on utilizing human intellectual resources from varying viewpoints to make informed decisions on issues from conservation biology to biotechnology, or even bioengineering. An increase in Latina/o students in the biological sciences would bring a variety of viewpoints, as well as personal and cultural experiences that would advance the field. To insure that we have enough experts in biology that represent changes in demographic trends, we must look into utilizing the expertise of students in our current educational system to continue and complete careers in biology. In this study, a career in biology referred to careers that require an expertise in biology that is gained by completing a bachelor's degree in biology or an affiliated field. Using case study methodology, I explored the experiences of two Latina students, one who is undocumented, and focused on the nature of the experiences and how they related to the young women's decision to pursue a career in biology. This study is grounded on a theoretical framework of critical systems theory and the notion that there are systems and components within those systems that either facilitate or hinder students' ability to pursue various pathways. Data were generated from semi-structured interviews, artifacts, life narratives, and cultural descriptors to gain an understanding of the girls' past, present, and future decisions regarding the feasibility of pursuing a degree in biology. Four common themes emerged: (1) experiences that made a lasting positive or negative impact early in life; (2) an intrinsic desire to serve their community or people in need; (3) sociocultural support networks; and (4) opportunities or circumstances within the cultural commons associated with their legal status in the United States, which caused the girls to continue or to deviate from their path towards pursuing a career in biology.

  2. Three Affliated Tribes Renewable Energy Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Belvin Pete; Kent Good; Krista Gordon; Ed McCarthy,

    2006-05-26

    The Three Affliated Tribes on the Fort Berthold Reservation studied the feasibility of a commercial wind facility on land selected and owned by the Tribes and examined the potential for the development of renewable energy resources on Tribal Lands.

  3. Conceptual Thermal Treatment Technologies Feasibility Study

    International Nuclear Information System (INIS)

    Suer, A.

    1996-01-01

    This report presents a conceptual Thermal Treatment Technologies Feasibility Study (FS) for the Savannah River Site (SRS) focusing exclusively on thermal treatment technologies for contaminated soil, sediment, or sludge remediation projects

  4. Feasibility study of renewable energy resources and optimization of electrical hybrid energy systems: Case study for Islamic Azad University, South Tehran Branch, Iran

    Directory of Open Access Journals (Sweden)

    Fazelpour Farivar

    2017-01-01

    Full Text Available Renewable energies are increasingly seen as the best solution to a growing global population demanding affordable access to electricity while reducing the need for fossil fuels. Country of Iran has vast untapped solar, wind, geothermal and hydroelectric sources that hold the potential to meet domestic needs. Renewable energy is also essential to Iran as it will curb massive air pollution. In this paper economical and feasibility study of various hybrid systems are performed by using HOMER software model for supplying electricity to the Engineering Department of Islamic Azad University. For this study, annual electricity demand of the university is 1,174,935 kWh with a peak demand of about 331 kW, average wind speeds, based on hourly data during the period of eleven years (2000-2010, are between 3 to 5 m/s in all months of the year. For solar radiation, six models are evaluated to select the best model for estimation of the daily global solar radiation (GSR on a horizontal surface in the study location. Among these six models, H/HO=a+b (S/S0+ c(S/S02 is chosen as the most optimum model for estimating solar irradiation. The results indicate that among the three hybrid systems for fulfilling electrical energy needs, the Wind/Diesel/Battery hybrid system with 9 wind turbines (20 kW, one diesel generator (300 kW, 50 batteries, and 50 kW power converters with net present cost of $4,281,800 and cost of energy of 0.285 $/kWh is the most economically efficient hybrid system. (based on 2015 US dollar.

  5. White Earth Biomass/Biogas Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Triplett, Michael

    2015-03-12

    The White Earth Nation examined the feasibility of cost savings and fossil energy reduction through the installation of biogas/biomass boiler at the tribal casino. The study rejected biogas options due to availability and site constraints, but found a favorable environment for technical and financial feasibility of installing a 5 MMBtu hot water boiler system to offset 60-70 percent of current fuel oil and propane usage.

  6. Financial Feasibility of Kerupuk Jari Processing Business in Pasir Utama Village Rambah Hilir District Rokan Hulu Regency (a Case Study Processing Business Kerupuk Jari Mr. Andika)

    OpenAIRE

    Aprilianto, Gatut Sudi

    2016-01-01

    High demand for crackers making business opportunities for cracker processing business, however, in making cracker processing business entrepreneurs typically do not conduct financial records, so it is not known how the expenditure and revenue to the business. This study aims to determine the income and financial feasibility of kerupuk jari processing business. The research was conducted from December 2015 through January 2016. Data collection methods used were interviews with respondents and...

  7. River Wyre preliminary feasibility study

    International Nuclear Information System (INIS)

    1991-01-01

    A study undertaken in 1987 for the Department of Energy, of small estuaries and embayments around the coast of the United Kingdom, identified the Wyre as one of the most promising sites for the construction of a small tidal power barrage. Enquiries showed that Organisations with interests in and around the Wyre had carried out extensive surveys and investigations into the physical and environmental aspects of the estuary, many of which would be relevant to the development of a tidal power scheme. It was identified that a barrage constructed on the Wyre, in addition to generating clean renewable energy may also act as a road crossing between Fleetwood and Over Wyre, thereby avoiding the present diversion via the Shard Toll Bridge located some 8km upstream of the town of Fleetwood. (Author)

  8. Viscosity Control Experiment Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Morris, Heidi E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Bradley, Paul Andrew [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2018-01-31

    Turbulent mix has been invoked to explain many results in Inertial Confinement Fusion (ICF) and High Energy Density (HED) physics, such as reduced yield in capsule implosions. Many ICF capsule implosions exhibit interfacial instabilities seeded by the drive shock, but it is not clear that fully developed turbulence results from this. Many simulations use turbulent mix models to help match simulation results to data, but this is not appropriate if turbulence is not present. It would be useful to have an experiment where turbulent mixing could be turned on or off by design. The use of high-Z dopants to modify viscosity and the resulting influence on turbulence is considered here. A complicating factor is that the plasma in some implosions can become strongly coupled, which makes the Spitzer expression for viscosity invalid. We first consider equations that cover a broad parameter space in temperature and density to address regimes for various experimental applications. Next, a previous shock-tube and other ICF experiments that investigate viscosity or use doping to examine the effects on yield are reviewed. How viscosity and dopants play a role in capsule yield depends on the region and process under consideration. Experiments and simulations have been performed to study the effects of viscosity on both the hot spot and the fuel/ablator mix. Increases in yield have been seen for some designs, but not all. We then discuss the effect of adding krypton dopant to the gas region of a typical OMEGA and a 2-shock NIF implosion to determine approximately the effect of adding dopant on the computed Reynolds number. Recommendations for a path forward for possible experiments using high-Z dopants to affect viscosity and turbulence are made.

  9. The feasibility study: a health economics perspective

    Directory of Open Access Journals (Sweden)

    Brenda Gannon

    2017-02-01

    Full Text Available The remit of research funding bodies is to prioritise funding for research that is of relevance and of high quality. This in turn will aim to raise the quality of healthcare and benefit to patients. Researchers are faced with increasing demands and expectations from the public purse and patients. The emphasis is to improve the quality of their research, with the ultimate aim of improving population health. While guidelines on feasibility study methods concentrate heavily on trials, there appears less guidance on application of health economics within feasibility studies, yet these are a less costly way to determine first of all if a full randomised controlled trial (RCT is feasible. A feasibility study assesses if the study can be done in a small RCT type study. Since by definition, a feasibility study does not evaluate the outcome, researchers often omit the health economics aspects but do however include statistical analysis. This leaves a gap in interpretation for policy makers and potential funders. It also means that any resulting publication does not include relevant information and therefore comparison across studies in terms of difficulty in collecting cost data is not possible. The main aim of this commentary therefore, is to demonstrate a suggested health economics analysis within a feasibility study and to recommend to researchers to include these aspects from the conception of their intervention. This paper proposes a number of points, with rationale for each point, to indicate the health economics data and the potential benefits required for coherent interpretation of the feasibility of future economic evaluations in a full trial. Economic evaluation is necessary if implementation into standard care is anticipated. Therefore, collection and summary analysis of relevant data is good practice at each point of the intervention development. Current guidelines for economic evaluation, for example, The Medical Research Guidelines in the

  10. A cask maintenance facility feasibility study

    International Nuclear Information System (INIS)

    Rennich, M.J.; Medley, L.G.; Attaway, C.R.

    1989-01-01

    The Oak Ridge National Laboratory (ORNL) is developing a transportation system for spent nuclear fuel (SNF) and defense high level waste (HLW) as a part of the Federal Waste Management System (FWMS). In early 1988, a feasibility study was undertaken to design a stand-alone, ''green field'' facility for maintaining the FWMS casks. The feasibility study provided an initial layout facility design, an estimate of the construction cost, and an acquisition schedule for a Cask Maintenance Facility (CMF). The study also helped to define the interfaces between the transportation system and the waste generators, the repository, and a Monitored Retrievable Storage (MRS) facility. The data, design, and estimated costs resulting from the study have been organized for use in the total transportation system decision-making process. Most importantly, the feasibility study also provides a foundation for continuing design and planning efforts. Fleet servicing facility studies, operational studies from current cask system operators, a definition of the CMF system requirements, and the experience of others in the radioactive waste transportation field were used as a basis for the feasibility study. In addition, several cask handling facilities were visited to observe and discuss cask operations to establish the functions and methods of cask maintenance expected to be used in the facility. Finally, a peer review meeting was held at Oak Ridge, Tennessee in August, 1988, in which the assumptions, design, layout, and functions of the CMF were significantly refined. Attendees included representatives from industry, the repository and transportation operations

  11. Automated docking screens: a feasibility study.

    Science.gov (United States)

    Irwin, John J; Shoichet, Brian K; Mysinger, Michael M; Huang, Niu; Colizzi, Francesco; Wassam, Pascal; Cao, Yiqun

    2009-09-24

    Molecular docking is the most practical approach to leverage protein structure for ligand discovery, but the technique retains important liabilities that make it challenging to deploy on a large scale. We have therefore created an expert system, DOCK Blaster, to investigate the feasibility of full automation. The method requires a PDB code, sometimes with a ligand structure, and from that alone can launch a full screen of large libraries. A critical feature is self-assessment, which estimates the anticipated reliability of the automated screening results using pose fidelity and enrichment. Against common benchmarks, DOCK Blaster recapitulates the crystal ligand pose within 2 A rmsd 50-60% of the time; inferior to an expert, but respectrable. Half the time the ligand also ranked among the top 5% of 100 physically matched decoys chosen on the fly. Further tests were undertaken culminating in a study of 7755 eligible PDB structures. In 1398 cases, the redocked ligand ranked in the top 5% of 100 property-matched decoys while also posing within 2 A rmsd, suggesting that unsupervised prospective docking is viable. DOCK Blaster is available at http://blaster.docking.org .

  12. A cask maintenance facility feasibility study

    International Nuclear Information System (INIS)

    Rennich, M.J.; Medley, L.G.; Attaway, C.R.

    1989-01-01

    The Oak Ridge National Laboratory (ORNL) is supporting the USDOE Office of Civilian Radioactive Waste Management (OCRWM) in developing a transportation system for spent nuclear fuel (SNF) and defense high level waste (HLW) as a part of the Federal Waste Management System (FWMS). In early 1988, a feasibility study was undertaken to design a stand-alone, green field facility for maintaining the FWMS casks. The feasibility study provided an initial layout facility design, an estimate of the construction cost, and an acquisition schedule for a Cask Maintenance Facility (CMF). The study also helped to define the interfaces between the transportation system and the waste generators, the repository, and a Monitored Retrieveable Storage (MRS) facility. The data, design, and estimated cost resulting from the study have been organized for use in the total transportation system decision-making process. Most importantly, the feasibility study also provides a foundation for continuing design and planning efforts. The feasibility study was based on an assumed stand-alone green field configuration because of the flexibility this design approach provides. A stand-alone facility requires the inclusion with support functions as well as the primary process facilities thus yielding a comprehensive design evaluation and cost estimate. For example, items such as roads, security and waste processing which might be shared with an integrated or collocated facility have been fully costed in the feasibility study. Thus, while the details of the facility design might change, the overall concept used in the study can be applied to other facility configurations as planning for the total FWMS develops

  13. Bond Feasibility Study. Project Identification Committee Report.

    Science.gov (United States)

    Wichita Public Schools, KS.

    A committee, appointed by the Board of Education, was requested to make a comprehensive study of the school building needs of Unified School District No. 259. In an attempt to determine the feasibility of a general bond election to upgrade the public schools, the specific charge to the committee was to evaluate the needs for physical plant…

  14. Technical feasibility study on polycarbonate solar panels

    NARCIS (Netherlands)

    Hackmann, M.M.; Meuwissen, M.H.H.; Bots, T.L.; Buijs, J.A.H.M.; Broek, K.M.; Kinderman, R.; Tanck, O.B.F.; Schuurmans, F.M.

    2004-01-01

    This paper describes a technical feasibility study on the application of polycarbonate (PC) plates in a superstrate photovoltaic module design. The lamination process was performed in a conventional laminator apparatus using low temperature curing (100°C) ethylene-vinyl-acetate (EVA) as the potting

  15. Impact of cancer and chemotherapy on autonomic nervous system function and cardiovascular reactivity in young adults with cancer: a case-controlled feasibility study.

    Science.gov (United States)

    Adams, Scott C; Schondorf, Ronald; Benoit, Julie; Kilgour, Robert D

    2015-05-18

    Preliminary evidence suggests cancer- and chemotherapy-related autonomic nervous system (ANS) dysfunction may contribute to the increased cardiovascular (CV) morbidity- and mortality-risks in cancer survivors. However, the reliability of these findings may have been jeopardized by inconsistent participant screening and assessment methods. Therefore, good laboratory practices must be established before the presence and nature of cancer-related autonomic dysfunction can be characterized. The purpose of this study was to assess the feasibility of conducting concurrent ANS and cardiovascular evaluations in young adult cancer patients, according to the following criteria: i) identifying methodological pitfalls and proposing good laboratory practice criteria for ANS testing in cancer, and ii) providing initial physiologic evidence of autonomic perturbations in cancer patients using the composite autonomic scoring scale (CASS). Thirteen patients (mixed diagnoses) were assessed immediately before and after 4 cycles of chemotherapy. Their results were compared to 12 sex- and age-matched controls. ANS function was assessed using standardized tests of resting CV (tilt-table, respiratory sinus arrhythmia and Valsalva maneuver) and sudomotor (quantitative sudomotor axon reflex test) reactivity. Cardiovascular reactivity during exercise was assessed using a modified Astrand-Ryhming cycle ergometer protocol. Our feasibility criteria addressed: i) recruitment potential, ii) retention rates, iii) pre-chemotherapy assessment potential, iv) test performance/tolerability, and v) identification and minimizing the influence of potentially confounding medication. T-tests and repeated measures ANOVAs were used to assess between- and within-group differences at baseline and follow-up. The overall success rate in achieving our feasibility criteria was 98.4 %. According to the CASS, there was evidence of ANS impairment at baseline in 30.8 % of patients, which persisted in 18.2 % of patients

  16. Impact of cancer and chemotherapy on autonomic nervous system function and cardiovascular reactivity in young adults with cancer: a case-controlled feasibility study

    International Nuclear Information System (INIS)

    Adams, Scott C.; Schondorf, Ronald; Benoit, Julie; Kilgour, Robert D.

    2015-01-01

    Preliminary evidence suggests cancer- and chemotherapy-related autonomic nervous system (ANS) dysfunction may contribute to the increased cardiovascular (CV) morbidity- and mortality-risks in cancer survivors. However, the reliability of these findings may have been jeopardized by inconsistent participant screening and assessment methods. Therefore, good laboratory practices must be established before the presence and nature of cancer-related autonomic dysfunction can be characterized. The purpose of this study was to assess the feasibility of conducting concurrent ANS and cardiovascular evaluations in young adult cancer patients, according to the following criteria: i) identifying methodological pitfalls and proposing good laboratory practice criteria for ANS testing in cancer, and ii) providing initial physiologic evidence of autonomic perturbations in cancer patients using the composite autonomic scoring scale (CASS). Thirteen patients (mixed diagnoses) were assessed immediately before and after 4 cycles of chemotherapy. Their results were compared to 12 sex- and age-matched controls. ANS function was assessed using standardized tests of resting CV (tilt-table, respiratory sinus arrhythmia and Valsalva maneuver) and sudomotor (quantitative sudomotor axon reflex test) reactivity. Cardiovascular reactivity during exercise was assessed using a modified Astrand-Ryhming cycle ergometer protocol. Our feasibility criteria addressed: i) recruitment potential, ii) retention rates, iii) pre-chemotherapy assessment potential, iv) test performance/tolerability, and v) identification and minimizing the influence of potentially confounding medication. T-tests and repeated measures ANOVAs were used to assess between- and within-group differences at baseline and follow-up. The overall success rate in achieving our feasibility criteria was 98.4 %. According to the CASS, there was evidence of ANS impairment at baseline in 30.8 % of patients, which persisted in 18.2 % of patients

  17. Intensive virtual reality-based training for upper limb motor function in chronic stroke: a feasibility study using a single case experimental design and fMRI.

    Science.gov (United States)

    Schuster-Amft, Corina; Henneke, Andrea; Hartog-Keisker, Birgit; Holper, Lisa; Siekierka, Ewa; Chevrier, Edith; Pyk, Pawel; Kollias, Spyros; Kiper, Daniel; Eng, Kynan

    2015-01-01

    To evaluate feasibility and neurophysiological changes after virtual reality (VR)-based training of upper limb (UL) movements. Single-case A-B-A-design with two male stroke patients (P1:67 y and 50 y, 3.5 and 3 y after onset) with UL motor impairments, 45-min therapy sessions 5×/week over 4 weeks. Patients facing screen, used bimanual data gloves to control virtual arms. Three applications trained bimanual reaching, grasping, hand opening. Assessments during 2-week baseline, weekly during intervention, at 3-month follow-up (FU): Goal Attainment Scale (GAS), Chedoke Arm and Hand Activity Inventory (CAHAI), Chedoke-McMaster Stroke Assessment (CMSA), Extended Barthel Index (EBI), Motor Activity Log (MAL). Functional magnetic resonance imaging scans (FMRI) before, immediately after treatment and at FU. P1 executed 5478 grasps (paretic arm). Improvements in CAHAI (+4) were maintained at FU. GAS changed to +1 post-test and +2 at FU. P2 executed 9835 grasps (paretic arm). CAHAI improvements (+13) were maintained at FU. GAS scores changed to -1 post-test and +1 at FU. MAL scores changed from 3.7 at pre-test to 5.5 post-test and 3.3 at FU. The VR-based intervention was feasible, safe, and intense. Adjustable application settings maintained training challenge and patient motivation. ADL-relevant UL functional improvements persisted at FU and were related to changed cortical activation patterns. Implications for Rehabilitation YouGrabber trains uni- and bimanual upper motor function. Its application is feasible, safe, and intense. The control of the virtual arms can be done in three main ways: (a) normal (b) virtual mirror therapy, or (c) virtual following. The mirroring feature provides an illusion of affected limb movements during the period when the affected upper limb (UL) is resting. The YouGrabber training led to ADL-relevant UL functional improvements that were still assessable 12 weeks after intervention finalization and were related to changed cortical

  18. A Feasibility Study of Biogas Technology to Solving Peri-urban Sanitation Problems in Developing Countries. A Case for Harare, Zimbabwe

    Directory of Open Access Journals (Sweden)

    G Sibanda

    2013-06-01

    Full Text Available This study investigated the feasibility of converting organic waste into energy using biogas technology to address sanitation problems in peri-urban suburbs of Harare, Zimbabwe.These suburbs with an estimated population of 156.975 are unique in that they are not connected to the Harare main water sewer system. A baseline survey was conducted to determine the quantity of biodegradable human and kitchen waste (N=60. Biodigester sizing and costing was done for various scenarios mainly household standalone, single centralised suburb and combined suburbs centralised biogas models. In addition potential biogas conversion to electricity was done for single centralised suburb and combined suburbs centralised biogas models. This was followed by a cost benefit analysis of employing combined suburbs biogas technology. A combined suburbs centralised biogas model was found to be the most feasible scenario producing 7378 m3 of biogas per day with electricity production capacity of 384 kW .There was a potential of wood savings of 6129 tonnes/year, paraffin savings of 2.556 tonnes/year and greenhouse benefits of 980 tonnes of CO2 equivalent emissions/ year and which would attract U$2940 from carbon credits sales per year. The study recommended the adoption of the biogas technology because of its potential toaddress both economic and sanitation challenges being faced by local authorities in developing countries particularly, improved hygienic conditions, energy supply chronic epidemics and sewerreticulation.

  19. Renewable Energy Feasibility Study Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Rooney, Tim [Antares Group Inc.

    2013-10-30

    The Gila River Indian Community (GRIC or the Community) contracted the ANTARES Group, Inc. (“ANTARES”) to assess the feasibility of solar photovoltaic (PV) installations. A solar energy project could provide a number of benefits to the Community in terms of potential future energy savings, increased employment, environmental benefits from renewable energy generation and usage, and increased energy self-sufficiency. The study addresses a number of facets of a solar project’s overall feasibility, including: Technical appropriateness; Solar resource characteristics and expected system performance; Levelized cost of electricity (LCOE) economic assessment. The Gila River Indian Community (GRIC or the Community) contracted the ANTARES Group, Inc. (“ANTARES”) to prepare a biomass resource assessment study and evaluate the feasibility of a bioenergy project on Community land. A biomass project could provide a number of benefits to the Community in terms of increased employment, environmental benefits from renewable energy generation and usage, and increased energy self-sufficiency. The study addresses a number of facets of a biomass project’s overall feasibility, including: Resource analysis and costs; Identification of potential bioenergy projects; Technical and economic (levelized cost of energy) modeling for selected project configuration.

  20. Feasibility study on volcanic power generation system

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-07-01

    Investigations were carried out to determine the feasibility of volcanic power generation on Satsuma Io Island. Earthquakes were studied, as were the eruptions of subaerial and submarine hot springs. Hydrothermal rock alteration was studied and electrical surveys were made. General geophysical surveying was performed with thermocameras and radiation monitoring equipment. In particular, the Toyoba mine was studied, both with respect to its hot spring and its subsurface temperatures.

  1. Gasohol: economic feasibility study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    David, M. L.; Hammaker, G. S.; Buzenberg, R. J.; Wagner, J. P.

    1978-07-01

    This report was prepared by Development Planning and Research Associates, Inc. under a contract with the Energy Research and Development Center of the University of Nebraska in cooperation with the Agricultural Products Industrial Utilization Committee and the State of Nebraska. Funding for this study was provided to the Energy Research and Development Center by the U.S. Department of Energy and the Old West Regional Commission. The primary objective of the study was to: determine the fiscal and market conditions under which the production of gasohol would be profitable for private producers. For purposes of this study, gasohol is a motor fuel consisting of 10 percent agriculturally-derived anhydrous ethanol and 90 percent unleaded gasoline. The study assumes that gasohol can be a fuel substitute for gasoline; indeed, the cost of gasoline will significantly influence that for gasohol. Gasoline prices are determined by factors external to ethanol; thus, the economic feasibility study of gasohol is in large part an economic feasibility study of fuel-grade ethanol production. More specifically, the study examined the following: the technical aspects of distributing, marketing, and using gasohol; the costs of the distribution and marketing of ethanol and gasohol; the energy balance of ethanol production; the cost of producing ethanol; the factors influencing ehtanol plant size and location; and the conditions that would make ethanol economicaly feasible for private producers.

  2. Feasibility study on tandem fuel cycle

    International Nuclear Information System (INIS)

    Han, P.S.; Suh, I.S.; Rim, C.S.; Kim, B.K.; Suh, K.S.; Ro, S.K.; Juhn, P.I.; Kim, S.Y.

    1983-01-01

    The objective of this feasibility study is to review and assess the current state of technology concerning the tandem fuel cycle. Based on the results from this study, a long-term development plan suitable for Korea has been proposed for this cycle, i.e., the PWR → CANDU tandem fuel cycle which used plutonium and uranium, recovered from spent PWR fuel by co-processing, as fuel material for CANDU reactors. (Author)

  3. Human reliability data bank: feasibility study

    International Nuclear Information System (INIS)

    Comer, K.; Miller, D.P.; Donovan, M.

    1984-01-01

    The US Nuclear Regulatory Commission and Sandia National Laboratories have been developing a plan for a human reliability data bank since August 1981. This research is in response to the data needs of the nuclear power industry's probabilistic risk assessment community. The three phases of the program are to: (A) develop the data bank concept, (B) develop an implementation plan and conduct a feasibility study, and (C) assist a sponsor in implementing the data bank. The program is now in Phase B. This paper describes the methods used in the feasibility study. Decisions to be made in the future regarding full-scale implementation will be based, in part, on the outcome of this study. 3 references, 2 figures

  4. Leprosy Post-Exposure Prophylaxis (LPEP) programme: study protocol for evaluating the feasibility and impact on case detection rates of contact tracing and single dose rifampicin.

    Science.gov (United States)

    Barth-Jaeggi, Tanja; Steinmann, Peter; Mieras, Liesbeth; van Brakel, Wim; Richardus, Jan Hendrik; Tiwari, Anuj; Bratschi, Martin; Cavaliero, Arielle; Vander Plaetse, Bart; Mirza, Fareed; Aerts, Ann

    2016-11-17

    The reported number of new leprosy patients has barely changed in recent years. Thus, additional approaches or modifications to the current standard of passive case detection are needed to interrupt leprosy transmission. Large-scale clinical trials with single dose rifampicin (SDR) given as post-exposure prophylaxis (PEP) to contacts of newly diagnosed patients with leprosy have shown a 50-60% reduction of the risk of developing leprosy over the following 2 years. To accelerate the uptake of this evidence and introduction of PEP into national leprosy programmes, data on the effectiveness, impact and feasibility of contact tracing and PEP for leprosy are required. The leprosy post-exposure prophylaxis (LPEP) programme was designed to obtain those data. The LPEP programme evaluates feasibility, effectiveness and impact of PEP with SDR in pilot areas situated in several leprosy endemic countries: India, Indonesia, Myanmar, Nepal, Sri Lanka and Tanzania. Complementary sites are located in Brazil and Cambodia. From 2015 to 2018, contact persons of patients with leprosy are traced, screened for symptoms and assessed for eligibility to receive SDR. The intervention is implemented by the national leprosy programmes, tailored to local conditions and capacities, and relying on available human and material resources. It is coordinated on the ground with the help of the in-country partners of the International Federation of Anti-Leprosy Associations (ILEP). A robust data collection and reporting system is established in the pilot areas with regular monitoring and quality control, contributing to the strengthening of the national surveillance systems to become more action-oriented. Ethical approval has been obtained from the relevant ethics committees in the countries. Results and lessons learnt from the LPEP programme will be published in peer-reviewed journals and should provide important evidence and guidance for national and global policymakers to strengthen current

  5. Feasibility Study of Renewable Energy in Singapore

    OpenAIRE

    King, Sebastian; Wettergren, Per

    2011-01-01

    Singapore is a country that is currently highly dependent on import of oil and gas. In order to be able to shift into a more sustainable energy system, Singapore is investing in research regarding different technologies and systems so as to establish more sustainable energy solutions. Seeing how air-conditioning accounts for approximately 30 % of Singapore’s total energy consumption, a feasibility study is being conducted on whether an integrated system using a thermally active building syste...

  6. COLD-SAT feasibility study safety analysis

    Science.gov (United States)

    Mchenry, Steven T.; Yost, James M.

    1991-01-01

    The Cryogenic On-orbit Liquid Depot-Storage, Acquisition, and Transfer (COLD-SAT) satellite presents some unique safety issues. The feasibility study conducted at NASA-Lewis desired a systems safety program that would be involved from the initial design in order to eliminate and/or control the inherent hazards. Because of this, a hazards analysis method was needed that: (1) identified issues that needed to be addressed for a feasibility assessment; and (2) identified all potential hazards that would need to be controlled and/or eliminated during the detailed design phases. The developed analysis method is presented as well as the results generated for the COLD-SAT system.

  7. Methodology study: Co-generation feasibility at sawmills

    International Nuclear Information System (INIS)

    Host, J.

    1991-01-01

    This report discussed the various factors that should be studied and evaluated before establishing a cogeneration plant. The results of three case studies and a survey of energy needs in smaller and medium size sawmills are also presented. In general, cogeneration is feasible for supplying electric energy required for processing logs using fuelbark and other residues from the manufacturing process. A rebuilt turbine-generator unit is an initial cost saving alternative that is advantageous throughout the life of the operation

  8. Feasibility of creating a high-resolution 3D diffusion tensor imaging based atlas of the human brainstem: a case study at 11.7 T.

    Science.gov (United States)

    Aggarwal, Manisha; Zhang, Jiangyang; Pletnikova, Olga; Crain, Barbara; Troncoso, Juan; Mori, Susumu

    2013-07-01

    A three-dimensional stereotaxic atlas of the human brainstem based on high resolution ex vivo diffusion tensor imaging (DTI) is introduced. The atlas consists of high resolution (125-255 μm isotropic) three-dimensional DT images of the formalin-fixed brainstem acquired at 11.7 T. The DTI data revealed microscopic neuroanatomical details, allowing three-dimensional visualization and reconstruction of fiber pathways including the decussation of the pyramidal tract fibers, and interdigitating fascicles of the corticospinal and transverse pontine fibers. Additionally, strong gray-white matter contrasts in the apparent diffusion coefficient (ADC) maps enabled precise delineation of gray matter nuclei in the brainstem, including the cranial nerve and the inferior olivary nuclei. Comparison with myelin-stained histology shows that at the level of resolution achieved in this study, the structural details resolved with DTI contrasts in the brainstem were comparable to anatomical delineation obtained with histological sectioning. Major neural structures delineated from DTI contrasts in the brainstem are segmented and three-dimensionally reconstructed. Further, the ex vivo DTI data are nonlinearly mapped to a widely-used in vivo human brain atlas, to construct a high-resolution atlas of the brainstem in the Montreal Neurological Institute (MNI) stereotaxic coordinate space. The results demonstrate the feasibility of developing a 3D DTI based atlas for detailed characterization of brainstem neuroanatomy with high resolution and contrasts, which will be a useful resource for research and clinical applications. Copyright © 2013 Elsevier Inc. All rights reserved.

  9. A SEISMIC DESIGN OF NUCLEAR REACTOR BUILDING STRUCTURES APPLYING SEISMIC ISOLATION SYSTEM IN A HIGH SEISMICITY REGION –A FEASIBILITY CASE STUDY IN JAPAN-

    Directory of Open Access Journals (Sweden)

    TETSUO KUBO

    2014-10-01

    Full Text Available A feasibility study on the seismic design of nuclear reactor buildings with application of a seismic isolation system is introduced. After the Hyogo-ken Nanbu earthquake in Japan of 1995, seismic isolation technologies have been widely employed for commercial buildings. Having become a mature technology, seismic isolation systems can be applied to NPP facilities in areas of high seismicity. Two reactor buildings are discussed, representing the PWR and BWR buildings in Japan, and the application of seismic isolation systems is discussed. The isolation system employing rubber bearings with a lead plug positioned (LRB is examined. Through a series of seismic response analyses using the so-named standard design earthquake motions covering the design basis earthquake motions obtained for NPP sites in Japan, the responses of the seismic isolated reactor buildings are evaluated. It is revealed that for the building structures examined herein: (1 the responses of both isolated buildings and isolating LRBs fulfill the specified design criteria; (2 the responses obtained for the isolating LRBs first reach the ultimate condition when intensity of motion is 2.0 to 2.5 times as large as that of the design-basis; and (3 the responses of isolated reactor building fall below the range of the prescribed criteria.

  10. A seismic design of nuclear reactor building structures applying seismic isolation system in a seismicity region-a feasibility case study in Japan

    Energy Technology Data Exchange (ETDEWEB)

    Kubo, Tetsuo [The University of Tokyo, Tokyo (Japan); Yamamoto, Tomofumi; Sato, Kunihiko [Mitsubishi Heavy Industries, Ltd., Kobe (Japan); Jimbo, Masakazu [Toshiba Corporation, Yokohama (Japan); Imaoka, Tetsuo [Hitachi-GE Nuclear Energy, Ltd., Hitachi (Japan); Umeki, Yoshito [Chubu Electric Power Co. Inc., Nagoya (Japan)

    2014-10-15

    A feasibility study on the seismic design of nuclear reactor buildings with application of a seismic isolation system is introduced. After the Hyogo-ken Nanbu earthquake in Japan of 1995, seismic isolation technologies have been widely employed for commercial buildings. Having become a mature technology, seismic isolation systems can be applied to NPP facilities in areas of high seismicity. Two reactor buildings are discussed, representing the PWR and BWR buildings in Japan, and the application of seismic isolation systems is discussed. The isolation system employing rubber bearings with a lead plug positioned (LRB) is examined. Through a series of seismic response analyses using the so-named standard design earthquake motions covering the design basis earthquake motions obtained for NPP sites in Japan, the responses of the seismic isolated reactor buildings are evaluated. It is revealed that for the building structures examined herein: (1) the responses of both isolated buildings and isolating LRBs fulfill the specified design criteria; (2) the responses obtained for the isolating LRBs first reach the ultimate condition when intensity of motion is 2.0 to 2.5 times as large as that of the design-basis; and (3) the responses of isolated reactor building fall below the range of the prescribed criteria.

  11. Analysis of economic feasibility of sale of surplus electricity in cogeneration: case study; Analise de viabilidade economica de venda de energia eletrica excedente em cogeracao: estudo de caso

    Energy Technology Data Exchange (ETDEWEB)

    Fodra, Marcelo [Universidade Estadual Paulista Julio de Mesquita Filho (FCA/UNESP), Botucatu, SP (Brazil). Fac. de Ciencias Agronomicas; Universidade Sagrado Coracao (USC), Bauru, SP (Brazil)], email: marcelo.fodra@fca.unesp.br; Esperancini, Maura Seiko Tsutsui [Universidade Estadual Paulista Julio de Mesquita Filho (FCA/UNESP), Botucatu, SP (Brazil). Fac. de Ciencias Agronomicas. Dept. de Gestao e Tecnologia Agroindustrial], email: maura@fca.unesp.br

    2010-07-01

    The production of energy in large quantity and at competitive prices is crucial for economic development, which allied to the environmental question, has incentivated the use of renewable sources of energy. One of the most promising sources of renewable energy is the cogeneration from the residues of cane. Currently, the scenario for this kind of energy production is not consolidated, as production prices are not stable, inducing a risky situation for the environment. This work was aimed to study the economic viability of installing a main site for cogeneration of electricity, in a regional sugarcane factory located in the central region of Sao Paulo state that currently uses residues of sugar cane as fuel. The risk factor that was taken into consideration was the price paid for the MWh sold to the Chamber of Commerce of Electricity. The Monte Carlo Method was used to assess the risk factors for the analysis, by using of New Present Value (NPV), in a scenario that uses 20% of the initial investment made by the energy dealer. After the simulations were finished, considering the conditions used in this work, the project tends to be not feasible, as the behavior of the prices of cogenerated MWh are not sufficient for paying the initial investment and the operational costs. (author)

  12. A Feasibility study of a mining business

    Directory of Open Access Journals (Sweden)

    Cehlár Michal

    2001-06-01

    Full Text Available The economic evaluation of a project requires a great deal of diverse information to be brought together in one place. The greatest concern is that there will be an error by omission, so it is useful to have a detailed list of what one needs to know in order to make a thorough evaluation.There are various of detail required at the different stages of evaluation in the project, from the "quick and dirty" overview to the pre-feasibility study, through a full detailed feasibility study, to a due diligence review. This list addresses most of the economic variables in project and can be used at all levels of studies. Its purpose is to identify a variable or issue and to raise a question, which the review can pursue in more detail using an increasingly more comprehensive checklist for each topic. While developed from the point of view of a new project, this list is equally valid for an ongoing operation.A feasibility study is defined as an assessment of all aspects of a project including technical, infrastructural, environmental, social, legislative and commercial factors, which is sufficiently detailed to support a decision on the implementation. Each project has an associated level of risk. For a proposed investment to increase the value of a firm's stock, it should have a higher expected rate of return than shareholders require for assuming that risk. Since investors demand for a higher potential returns from a riskier project, the cost of capital depends on the venture's risk.

  13. Feasibility study on intersection in North Sumatera

    Science.gov (United States)

    Hastuty, I. P.; Sembiring, I. S.; Anas, R.; Lubis, A. S.

    2018-02-01

    Traffic congestion is one of the problems faced by big cities, One of them is Binjai city and Medan city in North Sumatera. One of the causes of congestion is intersection of roads with highway and roads with railroads. To ensure the smooth movement of vehicles, technical handling at the intersection is needed. Therefore, it is necessary to pre-study the feasibility of level crossing in Binjai and Medan to be able to assess the investment needs and the level of importance of road development in the region. The development of transportation infrastructure and facilities is based on the thought of improving the transportation network system. The necessity of systemical integrated transportation system handling is needed in creating a transportation efficiency. The purpose of this study is to identify and prioritize the needs of the railway crossings. The objective which we want to be achieved is to obtain a document that contains technical, economic and environmental ability indicators as a reference in the feasibility and planning studies. The methodology used is collecting the primary data, secondary data, introduction of study area as the initial analysis of the problem. From the study it can be concluded that the existence of railway interchange will move the movement through traffic so it will not interfere the movement of traffic within urban areas and it keeps the national road network performance is still good.

  14. Feasibility Study of NMR Based Serum Metabolomic Profiling to Animal Health Monitoring: A Case Study on Iron Storage Disease in Captive Sumatran Rhinoceros (Dicerorhinus sumatrensis).

    Science.gov (United States)

    Watanabe, Miki; Roth, Terri L; Bauer, Stuart J; Lane, Adam; Romick-Rosendale, Lindsey E

    2016-01-01

    A variety of wildlife species maintained in captivity are susceptible to iron storage disease (ISD), or hemochromatosis, a disease resulting from the deposition of excess iron into insoluble iron clusters in soft tissue. Sumatran rhinoceros (Dicerorhinus sumatrensis) is one of the rhinoceros species that has evolutionarily adapted to a low-iron diet and is susceptible to iron overload. Hemosiderosis is reported at necropsy in many African black and Sumatran rhinoceroses but only a small number of animals reportedly die from hemochromatosis. The underlying cause and reasons for differences in susceptibility to hemochromatosis within the taxon remains unclear. Although serum ferritin concentrations have been useful in monitoring the progression of ISD in many species, there is some question regarding their value in diagnosing hemochromatosis in the Sumatran rhino. To investigate the metabolic changes during the development of hemochromatosis and possibly increase our understanding of its progression and individual susceptibility differences, the serum metabolome from a Sumatran rhinoceros was investigated by nuclear magnetic resonance (NMR)-based metabolomics. The study involved samples from female rhinoceros at the Cincinnati Zoo (n = 3), including two animals that died from liver failure caused by ISD, and the Sungai Dusun Rhinoceros Conservation Centre in Peninsular Malaysia (n = 4). Principal component analysis was performed to visually and statistically compare the metabolic profiles of the healthy animals. The results indicated that significant differences were present between the animals at the zoo and the animals in the conservation center. A comparison of the 43 serum metabolomes of three zoo rhinoceros showed two distinct groupings, healthy (n = 30) and unhealthy (n = 13). A total of eighteen altered metabolites were identified in healthy versus unhealthy samples. Results strongly suggest that NMR-based metabolomics is a valuable tool for animal health

  15. Feasibility Study of NMR Based Serum Metabolomic Profiling to Animal Health Monitoring: A Case Study on Iron Storage Disease in Captive Sumatran Rhinoceros (Dicerorhinus sumatrensis.

    Directory of Open Access Journals (Sweden)

    Miki Watanabe

    Full Text Available A variety of wildlife species maintained in captivity are susceptible to iron storage disease (ISD, or hemochromatosis, a disease resulting from the deposition of excess iron into insoluble iron clusters in soft tissue. Sumatran rhinoceros (Dicerorhinus sumatrensis is one of the rhinoceros species that has evolutionarily adapted to a low-iron diet and is susceptible to iron overload. Hemosiderosis is reported at necropsy in many African black and Sumatran rhinoceroses but only a small number of animals reportedly die from hemochromatosis. The underlying cause and reasons for differences in susceptibility to hemochromatosis within the taxon remains unclear. Although serum ferritin concentrations have been useful in monitoring the progression of ISD in many species, there is some question regarding their value in diagnosing hemochromatosis in the Sumatran rhino. To investigate the metabolic changes during the development of hemochromatosis and possibly increase our understanding of its progression and individual susceptibility differences, the serum metabolome from a Sumatran rhinoceros was investigated by nuclear magnetic resonance (NMR-based metabolomics. The study involved samples from female rhinoceros at the Cincinnati Zoo (n = 3, including two animals that died from liver failure caused by ISD, and the Sungai Dusun Rhinoceros Conservation Centre in Peninsular Malaysia (n = 4. Principal component analysis was performed to visually and statistically compare the metabolic profiles of the healthy animals. The results indicated that significant differences were present between the animals at the zoo and the animals in the conservation center. A comparison of the 43 serum metabolomes of three zoo rhinoceros showed two distinct groupings, healthy (n = 30 and unhealthy (n = 13. A total of eighteen altered metabolites were identified in healthy versus unhealthy samples. Results strongly suggest that NMR-based metabolomics is a valuable tool for

  16. Feasibility Study for the Development of SCWR

    International Nuclear Information System (INIS)

    Bae, Y. Y.; Kim, H. Y.; Cho, B. H.

    2010-04-01

    - As a result of feasibility study, following conclusions were drawn: · SCWR can be a strong candidate to a large-scale electric power production plant. · Infra-structure for development of an economic and safe SCWR is well established. · It is recommended to focus on the university-level fundamental research along with an international collaboration, for the time being. - The supercritical heat transfer research produced a lot of database on the small tubes and annular channels. - Among the candidate materials such as T92, Incolloy 800, MA956, ODS showed the superior characteristics

  17. Depleted uranium concrete container feasibility study

    International Nuclear Information System (INIS)

    Haelsig, R.T.

    1994-09-01

    The purpose of this report is to consider the feasibility of using containers constructed of depleted uranium aggregate concrete (DUCRETE) to store and transport radioactive materials. The method for this study was to review the advantages and disadvantages of DUCRETE containers considering design requirements for potential applications. The author found that DUCRETE is a promising material for onsite storage containers, provided DUCRETE vessels can be certified for one-way transport to disposal sites. The author also found that DUCRETE multipurpose spent nuclear fuel storage/transport packages are technically viable, provided altered temperature acceptance limits can be developed for DUCRETE

  18. Feasibility, safety, and economic implications of whey-recovered water in cleaning-in-place systems: A case study on water conservation for the dairy industry.

    Science.gov (United States)

    Meneses, Yulie E; Flores, Rolando A

    2016-05-01

    Water scarcity is threatening food security and business growth in the United States. In the dairy sector, most of the water is used in cleaning applications; therefore, any attempt to support water conservation in these processes will have a considerable effect on the water footprint of dairy products. This study demonstrates the viability for recovering good quality water from whey, a highly pollutant cheese-making by-product, to be reused in cleaning-in-place systems. The results obtained in this study indicate that by using a combined ultrafiltration and reverse osmosis system, 47% of water can be recovered. This system generates protein and lactose concentrates, by-products that once spray-dried fulfill commercial standards for protein and lactose powders. The physicochemical and microbiological quality of the recovered permeate was also analyzed, suggesting suitable properties to be reused in the cleaning-in-place system without affecting the quality and safety of the product manufactured on the cleaned equipment. A cost analysis was conducted for 3 cheese manufacturing levels, considering an annual production of 1, 20, and 225 million liters of whey. Results indicate the feasibility of this intervention in the dairy industry, generating revenues of $0.18, $3.05, and $33.4 million per year, respectively. The findings provide scientific evidence to promote the safety of reuse of reconditioned water in food processing plants, contributing to building a culture of water conservation and sustainable production throughout the food supply chain. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  19. Feasibility and economic analysis of solid desiccant wheel used for dehumidification and preheating in blast furnace: A case study of steel plant, Nanjing, China

    International Nuclear Information System (INIS)

    Guan, Yipeng; Zhang, Yufeng; Sheng, Ying; Kong, Xiangrui; Du, Song

    2015-01-01

    To overcome the shortcomings of huge energy consumption from conventional dehumidification using lithium bromide adsorption refrigerating (LBARD) system, a novel desiccant wheel dehumidification and preheating (DWDP) system using two-stage desiccant wheel for blast furnace is brought forward. The DWDP system was designed for dehumidification and preheating in blast furnace of steel plant. It takes waste heat in the slag flushing water as desiccant regeneration and preheating energy. To validate the feasibility of the new DWDP system, experimental studies were conducted based on a steel plant in Nanjing, China. The experiment was designed to use DWDP system in humid outdoor climates e.g. summer seasons. The experimental results indicate that the moisture removal capacity of DWDP system can reach 8.7 g/kg which will lead to the improvement of steel production by 0.9% and the coal is saved of about 2100 tons per year. With the DWDP system, the energy consumed by cooling tower of slag flushing water can decrease 7.3%. All of these energy saved equates to 10.3 million CNY annually. A comparison of initial investment and operating cost between DWDP system and LBRAD system was then carried out. The results show that the initial investment and operating cost of DWDP system is 37% and 57% of present LBARD system, and the payback period is shortened 66%. - Highlights: • A novel two-stage desiccant wheel dehumidification system for blast furnace is proposed. • Average moisture removal of 8.7 g/kg is achieved and dehumidification efficiency is 47%. • Outlet humidity ratio is less than 10 g/kg that satisfies the requirement of blast air. • Waste heat in slag flushing water is utilized and 61.4 million kJ is saved annually. • The investment and operating cost is 37% and 57% of former dehumidification system

  20. Battery energy storage market feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Kraft, S. [Frost and Sullivan, Mountain View, CA (United States); Akhil, A. [Sandia National Labs., Albuquerque, NM (United States). Energy Storage Systems Analysis and Development Dept.

    1997-07-01

    Under the sponsorship of the Department of Energy`s Office of Utility Technologies, the Energy Storage Systems Analysis and Development Department at Sandia National Laboratories (SNL) contracted Frost and Sullivan to conduct a market feasibility study of energy storage systems. The study was designed specifically to quantify the energy storage market for utility applications. This study was based on the SNL Opportunities Analysis performed earlier. Many of the groups surveyed, which included electricity providers, battery energy storage vendors, regulators, consultants, and technology advocates, viewed energy storage as an important enabling technology to enable increased use of renewable energy and as a means to solve power quality and asset utilization issues. There are two versions of the document available, an expanded version (approximately 200 pages, SAND97-1275/2) and a short version (approximately 25 pages, SAND97-1275/1).

  1. Battery energy storage market feasibility study

    International Nuclear Information System (INIS)

    Kraft, S.; Akhil, A.

    1997-07-01

    Under the sponsorship of the Department of Energy's Office of Utility Technologies, the Energy Storage Systems Analysis and Development Department at Sandia National Laboratories (SNL) contracted Frost and Sullivan to conduct a market feasibility study of energy storage systems. The study was designed specifically to quantify the energy storage market for utility applications. This study was based on the SNL Opportunities Analysis performed earlier. Many of the groups surveyed, which included electricity providers, battery energy storage vendors, regulators, consultants, and technology advocates, viewed energy storage as an important enabling technology to enable increased use of renewable energy and as a means to solve power quality and asset utilization issues. There are two versions of the document available, an expanded version (approximately 200 pages, SAND97-1275/2) and a short version (approximately 25 pages, SAND97-1275/1)

  2. Feasibility study on small modular reactors for modern microgrids

    Energy Technology Data Exchange (ETDEWEB)

    Islam, R.; Gabbar, H.A., E-mail: hossam.gabbar@uoit.ca [Univ. of Ontario Inst. of Technology, Faculty of Energy Systems and Nuclear Science, Oshawa, Ontario (Canada)

    2013-07-01

    Microgrid is a solution of conventional power grid problem and offer sustainable decentralized power system. Microgrid with modern distributed energy resources (DER) could play an important role to alleviate dependency on the main electricity grid. Distributed energy resource comprises wind turbine, solar photovoltaic, diesel generator, gas engine, micro turbine, fuel cells, etc.Due to the gap between typical loads and supply within microgrid, larger scale energy generation could provide a possible solution to balance power demand and supply. Feasibility study of Small Nuclear Power Plant, such as Small Modular reactor (SMR), within microgrids could be achieved via different cases. To achieve the target, a comprehensive feasibility study is conducted on microgrid with SMR through electricity generation profiles, geographical and environmental assessment, as well as cost analysis using simulation practices and data analysis.Also potency of SMRs is analyzed. Parameters and Key Performance Indicators (KPIs) could be analyzed to achieve feasible solution of microgrids with small modular reactor (SMR) to improve the overall microgrid performance.The study shows that SMR could be a feasible solution if microgrid parameters are selected properly. (author)

  3. Feasibility study on small modular reactors for modern microgrids

    International Nuclear Information System (INIS)

    Islam, R.; Gabbar, H.A.

    2013-01-01

    Microgrid is a solution of conventional power grid problem and offer sustainable decentralized power system. Microgrid with modern distributed energy resources (DER) could play an important role to alleviate dependency on the main electricity grid. Distributed energy resource comprises wind turbine, solar photovoltaic, diesel generator, gas engine, micro turbine, fuel cells, etc.Due to the gap between typical loads and supply within microgrid, larger scale energy generation could provide a possible solution to balance power demand and supply. Feasibility study of Small Nuclear Power Plant, such as Small Modular reactor (SMR), within microgrids could be achieved via different cases. To achieve the target, a comprehensive feasibility study is conducted on microgrid with SMR through electricity generation profiles, geographical and environmental assessment, as well as cost analysis using simulation practices and data analysis.Also potency of SMRs is analyzed. Parameters and Key Performance Indicators (KPIs) could be analyzed to achieve feasible solution of microgrids with small modular reactor (SMR) to improve the overall microgrid performance.The study shows that SMR could be a feasible solution if microgrid parameters are selected properly. (author)

  4. Using mixed methods evaluation to assess the feasibility of online clinical training in evidence based interventions: a case study of cognitive behavioural treatment for low back pain.

    Science.gov (United States)

    Richmond, Helen; Hall, Amanda M; Hansen, Zara; Williamson, Esther; Davies, David; Lamb, Sarah E

    2016-06-18

    Cognitive behavioural (CB) approaches are effective in the management of non-specific low back pain (LBP). We developed the CB Back Skills Training programme (BeST) and previously provided evidence of clinical and cost effectiveness in a large pragmatic trial. However, practice change is challenged by a lack of treatment guidance and training for clinicians. We aimed to explore the feasibility and acceptability of an online programme (iBeST) for providing training in a CB approach. This mixed methods study comprised an individually randomised controlled trial of 35 physiotherapists and an interview study of 8 physiotherapists. Participants were recruited from 8 National Health Service departments in England and allocated by a computer generated randomisation list to receive iBeST (n = 16) or a face-to-face workshop (n = 19). Knowledge (of a CB approach), clinical skills (unblinded assessment of CB skills in practice), self-efficacy (reported confidence in using new skills), attitudes (towards LBP management), and satisfaction were assessed after training. Engagement with iBeST was assessed with user analytics. Interviews explored acceptability and experiences with iBeST. Data sets were analysed independently and jointly interpreted. Fifteen (94 %) participants in the iBeST group and 16 (84 %) participants in the workshop group provided data immediately after training. We observed similar scores on knowledge (MD (95 % CI): 0.97 (-1.33, 3.26)), and self-efficacy to deliver the majority of the programme (MD (95 % CI) 0.25 (-1.7; 0.7)). However, the workshop group showed greater reduction in biomedical attitudes to LBP management (MD (95 % CI): -7.43 (-10.97, -3.89)). Clinical skills were assessed in 5 (33 %) iBeST participants and 7 (38 %) workshop participants within 6 months of training and were similar between groups (MD (95 % CI): 0.17(-0.2; 0.54)). Interviews highlighted that while initially sceptical, participants found iBeST acceptable. A number

  5. Aleutian Pribilof Islands Wind Energy Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Bruce A. Wright

    2012-03-27

    Under this project, the Aleutian Pribilof Islands Association (APIA) conducted wind feasibility studies for Adak, False Pass, Nikolski, Sand Point and St. George. The DOE funds were also be used to continue APIA's role as project coordinator, to expand the communication network quality between all participants and with other wind interest groups in the state and to provide continued education and training opportunities for regional participants. This DOE project began 09/01/2005. We completed the economic and technical feasibility studies for Adak. These were funded by the Alaska Energy Authority. Both wind and hydro appear to be viable renewable energy options for Adak. In False Pass the wind resource is generally good but the site has high turbulence. This would require special care with turbine selection and operations. False Pass may be more suitable for a tidal project. APIA is funded to complete a False Pass tidal feasibility study in 2012. Nikolski has superb potential for wind power development with Class 7 wind power density, moderate wind shear, bi-directional winds and low turbulence. APIA secured nearly $1M from the United States Department of Agriculture Rural Utilities Service Assistance to Rural Communities with Extremely High Energy Costs to install a 65kW wind turbine. The measured average power density and wind speed at Sand Point measured at 20m (66ft), are 424 W/m2 and 6.7 m/s (14.9 mph) respectively. Two 500kW Vestas turbines were installed and when fully integrated in 2012 are expected to provide a cost effective and clean source of electricity, reduce overall diesel fuel consumption estimated at 130,000 gallons/year and decrease air emissions associated with the consumption of diesel fuel. St. George Island has a Class 7 wind resource, which is superior for wind power development. The current strategy, led by Alaska Energy Authority, is to upgrade the St. George electrical distribution system and power plant. Avian studies in Nikolski

  6. CASE STUDY

    African Journals Online (AJOL)

    2011-06-02

    Jun 2, 2011 ... immunosuppression associated with HIV/AIDS puts them at a higher risk of developing oesophageal cancer. 47. CASE STUDY. A 49-year-old man was diagnosed as HIV infected, with a CD4 count of 60 cells/µl. He was started on an antiretroviral treatment regimen comprising zidovudine, lamivudine and ...

  7. Lunar Wireless Power Transfer Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Freid, Sheldon [National Security Technologies, LLC. (NSTec), Mercury, NV (United States); Popovic, Zoya [Univ. of Colorado, Boulder, CO (United States); Beckett, David R. [Independent Consultant; Anderson, Scott R. [Independent Consultant; Mann, Diana [Independent Consultant; Walker, Stuart [Independent Consultant

    2008-03-01

    This study examines the feasibility of a multi-kilowatt wireless radio frequency (RF) power system to transfer power between lunar base facilities. Initial analyses, show that wireless power transfer (WPT) systems can be more efficient and less expensive than traditional wired approaches for certain lunar and terrestrial applications. The study includes evaluations of the fundamental limitations of lunar WPT systems, the interrelationships of possible operational parameters, and a baseline design approach for a notionial system that could be used in the near future to power remote facilities at a lunar base. Our notional system includes state-of-the-art photovoltaics (PVs), high-efficiency microwave transmitters, low-mass large-aperture high-power transmit antennas, high-efficiency large-area rectenna receiving arrays, and reconfigurable DC combining circuitry.

  8. Feasibility Study for Paragon - Bisti Solar Ranch

    Energy Technology Data Exchange (ETDEWEB)

    Benally, Thomas [Navajo Hopi Land Commission Office (NHLCO), Window Rock, AZ (United States)

    2015-06-01

    The Navajo Hopi Land Commission Office (NHLCO) and Navajo Nation (NN) plan to develop renewable energy (RE) projects on the Paragon-Bisti Ranch (PBR) lands, set aside under the Navajo Hopi Land Settlement Act (NHLSA) for the benefit of Relocatees. This feasibility study (FS), which was funded under a grant from DOE’s Tribal Energy Program (TEP), was prepared in order to explore the development of the 22,000-acre PBR in northwestern New Mexico for solar energy facilities. Topics covered include: • Site Selection • Analysis of RE, and a Preliminary Design • Transmission, Interconnection Concerns and Export Markets • Financial and Economic Analysis • Environmental Study • Socioeconomic and Cultural Factors • Next Steps.

  9. Feasibility study on fission moly target development

    International Nuclear Information System (INIS)

    Kim, Byung Ku; Kim, Seong Nyun; Shon, Dong Seong; Choi, Chang Beom; Lee, Jae Kuk; Park, Jin Ho; Jeong, Won Myung; Jeon, Kwan Sik; You, Jae Hyung; Kang, Kyung Chul; Ahn, Jong Hwan; Ju, Po Kuk

    1996-01-01

    A multi-purpose research reactor, HANARO has been operated on the beginning of 1995 and can be utilized for production of various radioisotopes. And a R and D program for fission Mo production was established, and the technical and economical feasibility study has been performed for fission Mo production in Korea. In this study the process for fission Mo production was recommended as follows; 1. Target : UO 2 of annulus type. 2. Separation and purification : Nitric acid dissolution → Alumina adsorption → Benzoin oxime precipitation → Alumina adsorption. And more desirable plan for steady supply of fission Mo were suggested in following viewpoints; 1. Technical collaboration with foreign company. 2. Backup supply system. 3. Marketing arrangement. (Author)

  10. Exoskeleton for Soldier Enhancement Systems Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Jansen, J.F.

    2000-09-28

    The development of a successful exoskeleton for human performance augmentation (EHPA) will require a multi-disciplinary systems approach based upon sound biomechanics, power generation and actuation systems, controls technology, and operator interfaces. The ability to integrate key components into a system that enhances performance without impeding operator mobility is essential. The purpose of this study and report are to address the issue of feasibility of building a fieldable EHPA. Previous efforts, while demonstrating progress and enhancing knowledge, have not approached the level required for a fully functional, fieldable system. It is doubtless that the technologies required for a successful exoskeleton have advanced, and some of them significantly. The question to be addressed in this report is have they advanced to the point of making a system feasible in the next three to five years? In this study, the key technologies required to successfully build an exoskeleton have been examined. The primary focus has been on the key technologies of power sources, actuators, and controls. Power sources, including internal combustion engines, fuel cells, batteries, super capacitors, and hybrid sources have been investigated and compared with respect to the exoskeleton application. Both conventional and non-conventional actuator technologies that could impact EHPA have been assessed. In addition to the current state of the art of actuators, the potential for near-term improvements using non-conventional actuators has also been addressed. Controls strategies, and their implication to the design approach, and the exoskeleton to soldier interface have also been investigated. In addition to these key subsystems and technologies, this report addresses technical concepts and issues relating to an integrated design. A recommended approach, based on the results of the study is also presented.

  11. Feasibility studies for the Forward Spectrometer

    International Nuclear Information System (INIS)

    Biernat, Jacek

    2015-01-01

    The Forward Spectrometer designed for the P-barANDA detector will consist of many different detector systems allowing for precise track reconstruction and particle identification. Feasibility studies for Forward Spectrometer done by means of specific reactions will be presented. In the first part of the paper, results of simulations focussing on rate estimates of the tracking stations based on straw tubes will be presented. Next, the importance of the Forward Tracker will be demonstrated through the reconstruction of the ψ(4040) → DD-bar decay. Finally, results from the analysis of the experimental data collected with a straw tube prototype designed and constructed at the Research Center in Juelich will be discussed. (paper)

  12. Bin Set 1 Calcine Retrieval Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    R. D. Adams; S. M. Berry; K. J. Galloway; T. A. Langenwalter; D. A. Lopez; C. M. Noakes; H. K. Peterson; M. I. Pope; R. J. Turk

    1999-10-01

    At the Department of Energy's Idaho Nuclear Technology and Engineering Center, as an interim waste management measure, both mixed high-level liquid waste and sodium bearing waste have been solidified by a calculation process and are stored in the Calcine Solids Storage Facilities. This calcined product will eventually be treated to allow final disposal in a national geologic repository. The Calcine Solids Storage Facilities comprise seven ''bit sets.'' Bin Set 1, the first to be constructed, was completed in 1959, and has been in service since 1963. It is the only bin set that does not meet current safe-shutdown earthquake seismic criteria. In addition, it is the only bin set that lacks built-in features to aid in calcine retrieval. One option to alleviate the seismic compliance issue is to transport the calcine from Bin Set 1 to another bin set which has the required capacity and which is seismically qualified. This report studies the feasibility of retrieving the calcine from Bi n Set 1 and transporting it into Bin Set 6 which is located approximately 650 feet away. Because Bin Set 1 was not designed for calcine retrieval, and because of the high radiation levels and potential contamination spread from the calcined material, this is a challenging engineering task. This report presents preconceptual design studies for remotely-operated, low-density, pneumatic vacuum retrieval and transport systems and equipment that are based on past work performed by the Raytheon Engineers and Constructors architectural engineering firm. The designs presented are considered feasible; however, future development work will be needed in several areas during the subsequent conceptual design phase.

  13. Bin Set 1 Calcine Retrieval Feasibility Study

    International Nuclear Information System (INIS)

    Adams, R.D.; Berry, S.M.; Galloway, K.J.; Langenwalter, T.A.; Lopez, D.A.; Noakes, C.M.; Peterson, H.K.; Pope, M.I.; Turk, R.J.

    1999-01-01

    At the Department of Energy's Idaho Nuclear Technology and Engineering Center, as an interim waste management measure, both mixed high-level liquid waste and sodium bearing waste have been solidified by a calculation process and are stored in the Calcine Solids Storage Facilities. This calcined product will eventually be treated to allow final disposal in a national geologic repository. The Calcine Solids Storage Facilities comprise seven ''bit sets.'' Bin Set 1, the first to be constructed, was completed in 1959, and has been in service since 1963. It is the only bin set that does not meet current safe-shutdown earthquake seismic criteria. In addition, it is the only bin set that lacks built-in features to aid in calcine retrieval. One option to alleviate the seismic compliance issue is to transport the calcine from Bin Set 1 to another bin set which has the required capacity and which is seismically qualified. This report studies the feasibility of retrieving the calcine from Bi n Set 1 and transporting it into Bin Set 6 which is located approximately 650 feet away. Because Bin Set 1 was not designed for calcine retrieval, and because of the high radiation levels and potential contamination spread from the calcined material, this is a challenging engineering task. This report presents preconceptual design studies for remotely-operated, low-density, pneumatic vacuum retrieval and transport systems and equipment that are based on past work performed by the Raytheon Engineers and Constructors architectural engineering firm. The designs presented are considered feasible; however, future development work will be needed in several areas during the subsequent conceptual design phase

  14. Re: Cytoreductive Radical Prostatectomy in Patients with Prostate Cancer and Low Volume Skeletal Metastases: Results of a Feasibility and Case-Control Study

    Directory of Open Access Journals (Sweden)

    Axel Heidenreich

    2015-06-01

    Full Text Available Androgen deprivation therapy (ADT is currently the standard treatment for patients with metastatic prostate cancer (mPCa (1. Survival improvement after cytoreductive surgery is well known for kidney, breast, colon and ovarian cancers. The survival benefit of cytoreductive radical prostatectomy (CRP for mPCa was first hypothesized in a SEER-based study (2. Heidenreich et al. recently reported survival outcomes of CRP for mPCa. In the present study, 23 mPCa patients with less than 3 bone metastases, no visceral or extensive LN metastases and PSA less than 1.0 ng /mL after ADT were included. Control group (CG consisted of 38 mPCa patients treated with ADT alone. CRP and CG were equal with respect to patient demographics, tumor characteristics, and comorbidities. All patients had 50 mg bicalutamide with LHRH agonists at least for 6 months before surgery. Patients, who did not have PSA progression, were recommended to continue another 2 years of ADT before treatment stopped. When compared with CG, median time to castration resistance was statistically significantly longer in CRP group (40 vs 29 months, p=.014. At a median follow-up of 3 years, overall survival rates were 91.3% and 78.9% for CRP and CG, respectively (p=0.048. Cancer-specific survival rates were 95.6% and 84.2% for CRP and CG, respectively (p=0.043. Median clinical progression-free survival (PFS (range was 38.6 and 26.5 months in CRP and CGs, respectively (p= 0.032. This was the first case-control study that showed that CRP combined with ADT might offer better survival outcomes than ADT alone in mPCa patients. In spite of retrospective design and small cohort, the results are promising. There is an ongoing clinical trial testing the treatment efficacy of primary tumor in mPCa patients. This trial is going to compare efficacy of ADT therapy and ADT combined with either CRP or radiation (NCT01751438. SEER study was not a case-control study. This study further enhanced the hypothesis of

  15. Morbidity follow-up feasibility study

    International Nuclear Information System (INIS)

    Carpenter, M.

    1988-02-01

    The report reviews the available sources of data within Canada for undertaking morbidity follow-up studies to both supplement and complement studies using Canadian mortality data. Such studies would permit earlier detection and more sensitive measures of differences in risk for exposures to radiation and allow timely measures to be taken to minimize any occupational and environmental health risk to radiation workers. The technical feasibility of using these sources was reviewed using the criteria of adequate personal identifying information, automation of data records, file size and the accuracy of the morbidity diagnosis information. At the present time certain of the provincial cancer registry files meet these criteria best. A work plan was prepared suggesting a morbidity pilot study to clarify the role of occupational factors in the incidence of cancer among radiation workers using the Alberta Cancer Registry file and the National Dose Registry (NDR) file of radiation workers. For the longer term a full cohort study using the National Cancer Incidence Reporting System (NCIRS) and the NDR workers as the study population would provide information on all radiation workers on a national basis. A work plan was prepared and some initial format conversion of historical data was undertaken to begin developing the NCIRS into a data base suitable for long-term health studies

  16. Feasibility of including patients with migration background in a structured heart failure management programme: A prospective case-control study exemplarily on Turkish migrants.

    Directory of Open Access Journals (Sweden)

    Roman Pfister

    Full Text Available Structured management programmes deliver optimized care in heart failure patients and improve outcome. We examined the feasibility of including patients with migration background speaking little or no German in a heart failure management programme.After adaption of script material and staff to Turkish language we aimed to recruit 300 Turkish and 300 German (control group patients within 18 months using the operational basis of a local heart failure management programme for screening, contact and inclusion. Of 488 and 1,055 eligible Turkish and German patients identified through screening, 165 Turkish (34% and 335 German (32% patients consented on participation (p = 0.46. General practitioners contributed significantly more of the Turkish (84% than of the German patients (16%, p<0.001. Contact attempts by programme staff were significantly less successful in Turkish (52% than in German patients (60%, p = 0.005 due to significantly higher rate of missing phone numbers (36% vs 25%, invalid address data (28% vs 7% and being unreachable by phone more frequently (39% vs 26%, all p<0.001. Consent rate was significantly higher in successfully contacted Turkish (63% compared to German patients (50%, p<0.001.The inclusion of Turkish minority patients into a heart failure management programme is feasible with higher consent rate than in Germans. However, effort is high due to inherent logistic adaptions and barriers in identification and contacting of patients.DRKS00007780.

  17. Performance and Feasibility Analysis of a Grid Interactive Large Scale Wind/PV Hybrid System based on Smart Grid Methodology Case Study South Part – Jordan

    Directory of Open Access Journals (Sweden)

    Qais H. Alsafasfeh

    2015-02-01

    Full Text Available Most recent research on renewable energy resources main one goal to make Jordan less dependent on imported energy with locally developed and produced solar power, this paper discussed the efficient system of Wind/ PV Hybrid System to be than main power sources for south part of Jordan, the proposed hybrid system design based on Smart Grid Methodology,  the solar energy will be installed on top roof of  electricity subscribers across the Governorate of Maan, Tafila, Karak and Aqaba and the wind energy will set in one site by this way the capital cost for project will be reduced also the  simulation result show   the feasibility  is a very competitive and feasible cost . Economics analysis of a proposed renewable energy system was made using HOMER simulation and evaluation was completed with the cost per kilowatt of EDCO company, the net present cost is $2,551,676,416, the cost of energy is 0.07kWhr with a renewable fraction of 86.6 %.

  18. Neutron-gamma flux and dose calculations for feasibility study of DISCOMS instrumentation in case of severe accident in a GEN 3 reactor

    Science.gov (United States)

    Brovchenko, Mariya; Duhamel, Isabelle; Dechenaux, Benjamin

    2017-09-01

    The present paper presents the study carried out in the frame of the DISCOMS project, which stands for "DIstributed Sensing for COrium Monitoring and Safety". This study concerns the calculation of the neutron and gamma radiations received by the considered instrumentation during the normal reactor operation as well as in case of a severe accident for the EPR reactor, outside the reactor pressure vessel and in the containment basemat. This paper summarizes the methods and hypotheses used for the particle transport simulation outside the vessel during normal reactor operation. The results of the simulations are then presented including the responses for distributed Optical Fiber Sensors (OFS), such as the gamma dose and the fast neutron fluence, and for Self Powered Neutron Detectors (SPNDs), namely the neutron and gamma spectra. Same responses are also evaluated for severe accident situations in order to design the SPNDs being sensitive to the both types of received neutron-gamma radiation. By contrast, fibers, involved as transducers in distributed OFS have to resist to the total radiation gamma dose and neutron fluence received during normal operation and the severe accident.

  19. Northern gas: Williams petrochemical feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Chappell, D. [Williams Energy Canada, Calgary, AB (Canada)

    2002-07-01

    Williams Energy is a company that is involved in the following fields: gas pipelines, exploration and production, midstream, refining, petrochemical, power, and marketing and trading. The author provides an overview of the global and Canadian infrastructure before proceeding to discuss Arctic gas, which is viewed by Williams Energy as necessary. It favors the Alaska Highway route with a consortium for project development. Williams performed a petrochemical study to determine the feasibility of a petrochemical complex utilizing natural gas liquid from an Arctic gas pipeline. The scope of the study encompassed facilities (extraction plant, cracker, polyolefins plant), size (world scale, approximately 2 billion pounds per year), and location (Fairbanks or Alberta). The study led to the following findings: (1) review of several scenarios for both locations, (2) complex to produce two grades of polyethylene, (3) feedstock cost favors Alaska, (4) construction costs lower in Alberta, (5) and the primary market for the Alaska complex would be northeast Asia, while the primary market for the Alberta location would be the United States. It was determined that both options would be viable, however Alberta was favored due to the polyethylene forecast. The challenges still being faced by Williams include low frac spread, market inefficiencies, empress volumes, carbon dioxide, and fuel and electricity cost. Each of these challenges is discussed separately. The author concludes by indicating that incremental ethane is available, carbon dioxide issues need resolution, and Alberta and Alaska are attractive for Arctic ethane petrochemical production. figs.

  20. Feasibility study on floating nuclear power station

    International Nuclear Information System (INIS)

    Kajima, Ryoichi

    1987-01-01

    It is stipulated that nuclear power plants are to be built on solid rock bases on land in Japan. However, there are a limited number of appropriate siting grounds. The Central Research Institute of Electric Power Industry has engaged since 1981 in the studies on the construction technology of power plants, aiming at establishing new siting technology to expand the possible siting areas for nuclear power plants. Underground siting is regarded as a proven technology due to the experience in underground hydroelectric power plants. The technology of siting on quaternary ground is now at the stage of verification. In this report, the outline of floating type offshore/inshore siting technology is introduced, which is considered to be feasible in view of the technical and economical aspects. Three fixed structure types were selected, of which the foundations are fixed to seabed, plant superstructures are above sea surface, and which are floating type. Aiming at ensuring the aseismatic stability of the plant foundations, the construction technology is studied, and the structural concept omitting buoyancy is possible. The most practical water depth is not more than 20 m. The overall plant design, earthquake isolation effect and breakwater are described. (Kako, I.)

  1. Feasibility study on Ashuganj NGL Fractionation Plant

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A feasibility study has been performed on Ashuganj NGL Fractionation Plant being planned in the People's Republic of Bangladesh. The present study has discussed a plant to manufacture liquefied oil gas, automotive fuel, and diesel fuel from liquefied natural gas. The plan calls for the plant life of 20 years, liquefied natural gas as the raw material to be supplied continuously and stably from the gas reservoir areas via the existing pipelines, the storage tank to have a size of 10-day production, and the product to be transported by barges on Meghna River. As a result of the discussions, the liquefied oil gas produced annually will correspond to crude oil of 44,690 tons, and to 858,048 tons of crude oil cumulatively for 20 years of the plant life. This is an energy derived from unutilized natural gas, which is creation of a new energy. With regard to the reduction of global warming gas emission, it was revealed that a reduction effect of 16,540,000 t-CO2 can be obtained in twenty years, if comparison is made based on combustion of firewood. (NEDO)

  2. Feasibility study on Ashuganj NGL Fractionation Plant

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A feasibility study has been performed on Ashuganj NGL Fractionation Plant being planned in the People's Republic of Bangladesh. The present study has discussed a plant to manufacture liquefied oil gas, automotive fuel, and diesel fuel from liquefied natural gas. The plan calls for the plant life of 20 years, liquefied natural gas as the raw material to be supplied continuously and stably from the gas reservoir areas via the existing pipelines, the storage tank to have a size of 10-day production, and the product to be transported by barges on Meghna River. As a result of the discussions, the liquefied oil gas produced annually will correspond to crude oil of 44,690 tons, and to 858,048 tons of crude oil cumulatively for 20 years of the plant life. This is an energy derived from unutilized natural gas, which is creation of a new energy. With regard to the reduction of global warming gas emission, it was revealed that a reduction effect of 16,540,000 t-CO2 can be obtained in twenty years, if comparison is made based on combustion of firewood. (NEDO)

  3. SU-F-T-519: Is Geometry Based Setup Sufficient for All of the Head and Neck Treatment Cases?: A Feasibility Study Towards the Dose Based Setup

    International Nuclear Information System (INIS)

    Lee, S; Chen, S; Zhang, B; Xu, H; Prado, K; D’Souza, W; Yi, B

    2016-01-01

    Purpose: This study compares the geometric-based setup (GBS) which is currently used in the clinic to a novel concept of dose-based setup (DBS) of head and neck (H&N) patients using cone beam CT (CBCT) of the day; and evaluates the clinical advantages. Methods: Ten H&N patients who underwent re-simulation and re-plan due to noticeable anatomic changes during the course of the treatments were retrospectively reviewed on dosimetric changes in the assumption of no plan modification was performed. RayStation planning system (RaySearch Laboratories AB, Sweden) was used to match (ROI fusion module) between prescribed isodoseline (IDL) in the CBCT imported along with ROIs from re-planned CT and the IDL of original plan (Dose-based setup: DBS). Then, the CBCT plan based on daily setup using the GBS (previously used for a patient) and the DBS CBCT plan recalculated in RayStation compared against the original CT-sim plan. Results: Most of patients’ tumor coverage and OAR doses got generally worsen when the CBCT plans were compared with original CT-sim plan with GBS. However, when DBS intervened, the OAR dose and tumor coverage was better than the GBS. For example, one of patients’ daily average doses of right parotid and oral cavity increased to 26% and 36%, respectively from the original plan to the GBS planning. However, it only increased by 13% and 24%, respectively with DBS. GTV D95 coverage also decreased by 16% with GBS, but only 2% decreased with DBS. Conclusion: DBS method is superior to GBS to prevent any abrupt dose changes to OARs as well as PTV/CTV or GTV at least for some H&N cases. Since it is not known when the DBS is beneficial to the GBS, a system which enables the on-line DBS may be helpful for better treatment of H&N.

  4. SU-F-T-519: Is Geometry Based Setup Sufficient for All of the Head and Neck Treatment Cases?: A Feasibility Study Towards the Dose Based Setup

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S; Chen, S; Zhang, B; Xu, H; Prado, K; D’Souza, W; Yi, B [University of Maryland School of Medicine, Baltimore, MD (United States)

    2016-06-15

    Purpose: This study compares the geometric-based setup (GBS) which is currently used in the clinic to a novel concept of dose-based setup (DBS) of head and neck (H&N) patients using cone beam CT (CBCT) of the day; and evaluates the clinical advantages. Methods: Ten H&N patients who underwent re-simulation and re-plan due to noticeable anatomic changes during the course of the treatments were retrospectively reviewed on dosimetric changes in the assumption of no plan modification was performed. RayStation planning system (RaySearch Laboratories AB, Sweden) was used to match (ROI fusion module) between prescribed isodoseline (IDL) in the CBCT imported along with ROIs from re-planned CT and the IDL of original plan (Dose-based setup: DBS). Then, the CBCT plan based on daily setup using the GBS (previously used for a patient) and the DBS CBCT plan recalculated in RayStation compared against the original CT-sim plan. Results: Most of patients’ tumor coverage and OAR doses got generally worsen when the CBCT plans were compared with original CT-sim plan with GBS. However, when DBS intervened, the OAR dose and tumor coverage was better than the GBS. For example, one of patients’ daily average doses of right parotid and oral cavity increased to 26% and 36%, respectively from the original plan to the GBS planning. However, it only increased by 13% and 24%, respectively with DBS. GTV D95 coverage also decreased by 16% with GBS, but only 2% decreased with DBS. Conclusion: DBS method is superior to GBS to prevent any abrupt dose changes to OARs as well as PTV/CTV or GTV at least for some H&N cases. Since it is not known when the DBS is beneficial to the GBS, a system which enables the on-line DBS may be helpful for better treatment of H&N.

  5. Pinellas Plant feasibility study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-09-01

    The Pinellas Plant was built in 1956 to manufacture neutron generators, a principal component in nuclear weapons. In September 1990, the Department of Health and Rehabilitative Services (HRS) entered into an agreement with DOE to independently examine environmental monitoring data from the plant and health data from Pinellas County to determine if an epidemiological study is technically feasible to measure possible off-site health effects from ionizing radiation. Through normal plant operations, some radioactive materials have been released to the environment. Eighty percent of the total plant releases of 107,707 curies occurred in the early years of plant operation (1957--1960). The primary materials released were tritium gas, tritium oxide and krypton-85. Environmental monitoring for radioactive releases from the plant has been done regularly since 1975. The US Public Health Service Centers for Disease Control and Prevention (CDC), in assisting HRS, has determined that sufficient radiological data exist by which a dose reconstruction can be done. A dose reconstruction can provide an estimate of how much radiological exposure someone living in the vicinity of the Pinellas Plant may have suffered from environmental releases.

  6. Pinellas Plant feasibility study. Final report

    International Nuclear Information System (INIS)

    1994-09-01

    The Pinellas Plant was built in 1956 to manufacture neutron generators, a principal component in nuclear weapons. In September 1990, the Department of Health and Rehabilitative Services (HRS) entered into an agreement with DOE to independently examine environmental monitoring data from the plant and health data from Pinellas County to determine if an epidemiological study is technically feasible to measure possible off-site health effects from ionizing radiation. Through normal plant operations, some radioactive materials have been released to the environment. Eighty percent of the total plant releases of 107,707 curies occurred in the early years of plant operation (1957--1960). The primary materials released were tritium gas, tritium oxide and krypton-85. Environmental monitoring for radioactive releases from the plant has been done regularly since 1975. The US Public Health Service Centers for Disease Control and Prevention (CDC), in assisting HRS, has determined that sufficient radiological data exist by which a dose reconstruction can be done. A dose reconstruction can provide an estimate of how much radiological exposure someone living in the vicinity of the Pinellas Plant may have suffered from environmental releases

  7. Casing study

    Energy Technology Data Exchange (ETDEWEB)

    Roche, P.

    2000-12-01

    An unorthodox method of casing drilling used by Tesco Corporation at a gas well in Wyoming to drill deeper using casings as drillpipe is discussed. The process involves either rotating the casing as drill string or using a downhole mud motor to rotate the bit. In this instance, the surface hole and the production hole were casing-drilled to a record 8,312 feet by rotating the casing. The 8 1/2-inch surface hole was drilled with 7-inch casing to 1,200 feet using a Tesco underreamer and a polycrystalline pilot bit; drilling and cementing was completed in 12 1/2 hours. The 6 1/4-inch production hole was drilled with 4 1/2-inch casing and the bottomhole assembly was retrieved after 191 hours rotating. This case was the first in which the entire well was casing-drilled from surface to TD. Penetration rate compared favorably with conventional methods: 12 1/2 hours for casing-drilling to 18.9 hours for conventional drilling, despite the fact that the casing-drilling technology is still in its infancy. It is suggested that casing-drilling has the potential to eliminate the need for the drillpipe entirely. If these expectations were to be realised, casing-drilling could be one of the most radical drilling changes in the history of the oil and gas industry. 1 photo.

  8. Leprosy Post-Exposure Prophylaxis (LPEP) programme: Study protocol for evaluating the feasibility and impact on case detection rates of contact tracing and single dose rifampicin

    NARCIS (Netherlands)

    Barth-Jaeggi, T. (Tanja); Steinmann, P. (Peter); Mieras, L. (Liesbeth); W.H. van Brakel (Wim); J.H. Richardus (Jan Hendrik); Tiwari, A. (Anuj); Bratschi, M. (Martin); Cavaliero, A. (Arielle); Vander Plaetse, B. (Bart); Mirza, F. (Fareed); Aerts, A. (Ann)

    2016-01-01

    textabstractIntroduction: The reported number of new leprosy patients has barely changed in recent years. Thus, additional approaches or modifications to the current standard of passive case detection are needed to interrupt leprosy transmission. Large-scale clinical trials with single dose

  9. Feasibility study on embedded transport core calculations

    International Nuclear Information System (INIS)

    Ivanov, B.; Zikatanov, L.; Ivanov, K.

    2007-01-01

    The main objective of this study is to develop an advanced core calculation methodology based on embedded diffusion and transport calculations. The scheme proposed in this work is based on embedded diffusion or SP 3 pin-by-pin local fuel assembly calculation within the framework of the Nodal Expansion Method (NEM) diffusion core calculation. The SP 3 method has gained popularity in the last 10 years as an advanced method for neutronics calculation. NEM is a multi-group nodal diffusion code developed, maintained and continuously improved at the Pennsylvania State University. The developed calculation scheme is a non-linear iteration process, which involves cross-section homogenization, on-line discontinuity factors generation, and boundary conditions evaluation by the global solution passed to the local calculation. In order to accomplish the local calculation, a new code has been developed based on the Finite Elements Method (FEM), which is capable of performing both diffusion and SP 3 calculations. The new code will be used in the framework of the NEM code in order to perform embedded pin-by-pin diffusion and SP 3 calculations on fuel assembly basis. The development of the diffusion and SP 3 FEM code is presented first following by its application to several problems. Description of the proposed embedded scheme is provided next as well as the obtained preliminary results of the C3 MOX benchmark. The results from the embedded calculations are compared with direct pin-by-pin whole core calculations in terms of accuracy and efficiency followed by conclusions made about the feasibility of the proposed embedded approach. (authors)

  10. 7 CFR 1980.442 - Feasibility studies.

    Science.gov (United States)

    2010-01-01

    ... management, nature and extent of market area, marketing plans for sale of projected output, extent of... Agriculture Regulations of the Department of Agriculture (Continued) RURAL HOUSING SERVICE, RURAL BUSINESS...) PROGRAM REGULATIONS (CONTINUED) GENERAL Business and Industrial Loan Program § 1980.442 Feasibility...

  11. Feasibility study on rehabilitation of KESC gas turbine power plant

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to power generation facilities of Karachi Electric Power Supply Corporation in Karachi (KESC), the Islamic Republic of Pakistan, feasibility study on the rehabilitation was conducted in consideration of the CDM (clean development mechanism) project. In Pakistan, 13 gas turbine power plants started operation at the same time as the time when the power plant studied this time started operation, and therefore it is predicted that they also have the same troubles caused by the aged deterioration. As the rehabilitation project, two cases were proposed: In Case 1, gas turbine and generator are both exchanged, and in Case 2, gas turbine is only exchanged, and generator is reused after repair. The work term is approximately 9 months in both cases. The initial investment is $84 million in Case 1 and $78 million in Case 2. The energy conservation effect per cost is 107 t/y/million yen and 101 t/y/million yen, respectively. Further, the amount of greenhouse effect gas reduction per cost is 330 t-CO2/y/million yen and 313 t-CO2/y/million yen, respectively. The effect of profits can be obtained after the depreciation period since the fuel price is reduced approximately 0.5%. (NEDO)

  12. CASE STUDY

    African Journals Online (AJOL)

    HIV infection has several oral manifestations, including oral candidiasis and oral hairy leucoplakia. Occasionally unusual presentations requiring rigorous investigations are seen, and in these cases the diagnosis sometimes remains a dilemma owing to limited investigation facilities.1-3 We present the case of a patient who.

  13. B Plant process piping replacement feasibility study

    International Nuclear Information System (INIS)

    Howden, G.F.

    1996-01-01

    Reports on the feasibility of replacing existing embedded process piping with new more corrosion resistant piping between cells and between cells and a hot pipe trench of a Hanford Site style canyon facility. Provides concepts for replacement piping installation, and use of robotics to replace the use of the canyon crane as the primary means of performing/supporting facility modifications (eg, cell lining, pipe replacement, equipment reinstallation) and operational maintenenace

  14. Concurrent paclitaxel and radiotherapy. Treatment feasibility studies

    International Nuclear Information System (INIS)

    Vogt, H.G.; Martin, T.; Kolotas, C.; Hey, S.; Schneider, L.; Templin, T.; Zamboglou, N.; Dornoff, W.; Kettner, H.

    1997-01-01

    with 5x18 Gy/week up to 59.4 to 73.8 Gy. - VII. Concurrent paclitaxel and radiation for gliomas of the brain: 100 mg/m 2 paclitaxel as a 3-hour infusion weekly for 6 weeks simultaneous with radiotherapy in shrinking field technique with 5x2 Gy/week up to 60 Gy. Results: Our initial experiences with weekly application of paclitaxel as a 3-hour infusion in the dosages we used for simultaneous radiochemotherapy of malignancies in different anatomical sites has shown that this treatment concept is feasible, safe and effective. Conclusions: Whether this combined modality will enhance the response rates or influence survival rates has yet to be confirmed in phase-III studies. (orig.) [de

  15. case study

    African Journals Online (AJOL)

    Elton

    particularly in patients who commence ART with low CD4 counts and established opportunistic infections. IRIS results from a pathological inflammatory response to pre-existing infective, host or other antigens, alive or dead, causing clinical deterioration in HIV-infected patients after initiating ART.1 A case definition for IRIS ...

  16. CASE STUDY

    African Journals Online (AJOL)

    2010-09-01

    Sep 1, 2010 ... of the two diseases surgery can be successful, recovery can be similar to that .... lymphocytes predominated in 68% of cases, and that there was an .... using ferritin is the fact that it acts as an acute-phase reactant and will be ...

  17. Feasibility of estimate sediment yield in the non-sediment monitoring station area - A case study of Alishan River watershed,Taiwan

    Science.gov (United States)

    Chang, ChiaChi; Chan, HsunChuan; Jia, YaFei; Zhang, YaoXin

    2017-04-01

    Due to the steep topography, frail geology and concentrated rainfall in wet season, slope disaster occurred frequently in Taiwan. In addition, heavy rainfall induced landslides in upper watersheds. The sediment yield on the slopeland affects the sediment transport in the river. Sediment deposits on the river bed reduce the river cross section and change the flow direction. Furthermore, it generates risks to residents' lives and property in the downstream. The Taiwanese government has been devoting increasing efforts on the sedimentary management issues and on reduction in disaster occurrence. However, due to the limited information on the environmental conditions in the upper stream, it is difficult to set up the sedimentary monitoring equipment. This study used the upper stream of the Qingshuei River, the Alishan River, as a study area. In August 2009, Typhoon Morakot caused the sedimentation of midstream and downstream river courses in the Alishan River. Because there is no any sediment monitoring stations within the Alishan River watershed, the sediment yield values are hard to determine. The objective of this study is to establish a method to analyze the event-landslide sediment transport in the river on the upper watershed. This study numerically investigated the sediment transport in the Alishan River by using the KINEROS 2 model developed by the United States Department of Agriculture and the CCHE1D model developed by the National Center for Computational Hydroscience and Engineering. The simulated results represent the morphology changes in the Alishan River during the typhoon events. The results consist of a critical strategy reference for the sedimentary management for the Alishan River watershed.

  18. 100-BC-1 Operable Unit focused feasibility study

    International Nuclear Information System (INIS)

    Day, R.E.

    1994-01-01

    The standard Comprehensive Environmental Response, Compensation, and Liability Act feasibility study includes development and screening of alternatives (Phases 1 and 2) and the detailed analysis of alternatives (Phase 3). This focused feasibility study constitutes the Phase 3 portion of the feasibility study process for the remedial alternatives initially developed and screened in the 100 Area Feasibility Study Phases 1 and 2 (DOE-RL 1993a). The focused feasibility study process is conducted in two stages, a Process Document (DOE-RL 1994a) and an operable unit-specific focused feasibility study document, such as this one. The focused feasibility study process is performed by implementing a ''plug-in'' style approach; as defined in greater detail in the Process Document, which is a companion to this document. The objective of this focused feasibility study is to provide decision makers with sufficient information to allow appropriate and timely selection of interim remedial measures for candidate waste sites associated with the 100-BC-1 Operable Unit which is located in the north-central part of the Hanford Site. The interim remedial measure candidate waste sites are determined in the Limited Field Investigation (DOE-RL 1993b). Site profiles are developed for each of these waste sites. The site profiles are used in the application of the plug-in approach. The waste site either plugs into the analysis of the alternatives for the group, or deviations from the developed group alternatives are described and documented

  19. The Assessment of Water Treatment Plant Sludge Properties and the Feasibility of Its Re-use according to Environmental Standards: Shahid Beheshti Water Treatment Plant Case Study, Hamadan

    Directory of Open Access Journals (Sweden)

    H. Pourmand

    2016-04-01

    Full Text Available Introduction & Objectives: Water treatment leads to produce large volumes of sludges in water treatment plants which are considered as solid waste, and should be managed appropriately and logically to avoid bioenvironmental effects. Materials & Methods: In this cross-sectional study, the required samples were taken from the sludge of Shahid Beheshti water treatment plant to assay physical and chemical characteristics during one year from summer, autumn and winter 93 until spring 94. Sampling and testing procedures were full fit according to standard methods. Results: The average concentration of total solids parameters (TSS, total suspended solids (TSS, and total dissolved solids (TDS were 22346, 21350 and 1005 mg/L, respectively. Among the heavy metals, aluminum, iron, manganese and zinc have the highest concentrations with the values of 1400, 956, 588 and 100 mg per kg of dry solids, respectively. The measured concentrations for cadmium were also higher than the permissible limits for agricultural purposes and discharges into the environment. The average concentrations of nickel were more than the recommended standard for industrial, agricultural and parkland application purposes. The concentrations were also slurry higher than the dry sludge. Conclusion: According to the past studies and results of this study, it could be concluded that contamination of heavy metals in sludge and slurry samples are more than dried sludge, .Therefore, if they are discharged into the environment, it is better to be disposed as dry sludges. Furthermore, because these types of waste sludges are routinely disposed in the environment, it is recommended to take the routine samples in order to measure the heavy metals and other relevant parameters contents of sludge before discharging it. (Sci J Hamadan Univ Med Sci 2016; 23 (1:57-64

  20. Feasibility Study of Thin Film Thermocouple Piles

    Science.gov (United States)

    Sisk, R. C.

    2001-01-01

    Historically, thermopile detectors, generators, and refrigerators based on bulk materials have been used to measure temperature, generate power for spacecraft, and cool sensors for scientific investigations. New potential uses of small, low-power, thin film thermopiles are in the area of microelectromechanical systems since power requirements decrease as electrical and mechanical machines shrink in size. In this research activity, thin film thermopile devices are fabricated utilizing radio frequency sputter coating and photoresist lift-off techniques. Electrical characterizations are performed on two designs in order to investigate the feasibility of generating small amounts of power, utilizing any available waste heat as the energy source.

  1. The PHLAME firefighters' study: feasibility and findings.

    Science.gov (United States)

    Elliot, Diane L; Goldberg, Linn; Duncan, Terry E; Kuehl, Kerry S; Moe, Esther L; Breger, Rosemary K R; DeFrancesco, Carol L; Ernst, Denise B; Stevens, Victor J

    2004-01-01

    To assess efficacy of 2 worksite health promotion interventions. Randomly assign 3 fire stations to (a) team-based curriculum, (b) individual counselor meetings, and (c) control. Both interventions were feasible and acceptable, and they resulted in significant reductions in LDL cholesterol. The team approach significantly increased coworker cohesion, personal exercise habits, and coworkers' healthy behaviors. The one-on-one strategy significantly increased dietary self-monitoring, decreased fat intake, and reduced depressed feelings. Although both interventions promoted healthy behaviors, specific outcomes differed and reflected their conceptual underpinnings. The team-based curriculum is innovative and may enlist influences not accessed with individual formats.

  2. Nuclear power planning and feasibility studies

    International Nuclear Information System (INIS)

    Streeton, D.F.

    1977-01-01

    This lecture will review the basic steps associated with planning the introduction of nuclear power. Areas covered will include power market surveys, energy resources evaluations, potential alternative strategies, organisational factors and implementational requirements. The lecture will then consider the implications and requirements associated with establishing the feasibility of a nuclear project. Among others, aspects of power systems integration, site selection reactor type evaluation, cost and economic analysis, influence of contracting strategies, comparison with alternative power generation solutions, financial impact, etc. will be discussed and reviewed. (HK) [de

  3. Electrical Energy Storage Systems Feasibility; the Case of Terceira Island

    Directory of Open Access Journals (Sweden)

    Ana Rodrigues

    2017-07-01

    Full Text Available The Azores Regional Government, through the Sustainable Energy Action Plan for the Azorean Islands, assumed that by the year 2018, 60% of electricity would be generated from renewable energy sources. Nevertheless, by increasing renewable energy sources share in the electricity mix, peak energy that exceeds grid capacity cannot be used unless when considering energy storage systems. Therefore, this article aims at determining, among batteries and Pumped Hydro Systems, the most cost-effective energy storage system to deploy in Terceira Island, along with geothermal, wind, thermal and bio waste energy, while considering demand and supply constraints. It is concluded that a pumped hydro system sited in Serra do Morião-Nasce Água is the best option for storage of the excess generated energy when compared with batteries. However, further studies should analyze environmental constraints. It is demonstrated that by increasing the storage power capacity, a pumped hydro system improves its cost efficiency when compared with batteries. It is also demonstrated that, to ensure quality, economic feasibility, reliability and a reduction of external costs, it is preferable to replace fuel-oil by wind to generate electricity up to a conceivable technical limit, while building a pumped hydro system, or dumping the excess peak energy generated.

  4. Preliminary economic feasibility study of MIP (Medical Isotopes Producer)

    International Nuclear Information System (INIS)

    Mon, G. H.; O, S. Y.

    2004-01-01

    Preliminary economic feasibility study of MIP (Medical Isotopes Producer), which is used liquid nuclear fuel to produce medical isotopes of Mo-99 and Sr-89, was performed. To do this, this study was estimated the IRR(Internal Rate of Return) and PBP(Pay-back Period) about optimistic and pessimistic cases for market penetration of Asia and U.S.A. isotope markets. And sensitivity analysis is also performed about capital cost and price of Mo-99 and Sr-89. According to the results, IRR was between 14.9% and 24.3%, and PBP was between 4.8 years and 7.8 years. These suggest that MIP has economic merits. MIP can produce other medical isotopes such as Sr-90, I-131, Xe-133, Cs-137. So, it is necessary to do cost-benefit analysis considering production of these other isotopes

  5. Transvaginal uterosacral ligament hysteropexy: a retrospective feasibility study.

    Science.gov (United States)

    Milani, Rodolfo; Frigerio, Matteo; Manodoro, Stefano; Cola, Alice; Spelzini, Federico

    2017-01-01

    Uterine-sparing procedures could be attractive in patients concerned about preservation of fertility and change in corporeal image and sexuality. Transvaginal uterosacral hysteropexy can provide an alternative mesh-free technique for uterine suspension. This study aimed to evaluate the feasibility of transvaginal uterine suspension to uterosacral ligaments in terms of operative data, complications, midterm efficacy, and patient satisfaction. This retrospective study analyzed the first 20 cases of transvaginal hysteropexy through bilateral high uterosacral ligaments (modified Shull technique) performed in our Institution. Mean follow-up was 33.2 months. The procedure was performed in 84 ± 19 min ,and blood loss was 228 ± 139 ml. Three mild complications (15 %) were observed. Recurrence [Pelvic Organ Prolapse Quantification system (POP-Q) stage ≥ II was observed in five patients (25 %), and three of them (15 %) required reintervention. Mean Patient Global Impression of Improvement score was "much improved." Two woman (40 %) who had not fulfilled their childbearing desire obtained a pregnancy. Both underwent elective caesarean section at term. Transvaginal uterosacral hysteropexy appears a feasible mesh-free technique for apical support. This procedure can be indicated in women with the desire of preserving fertility or who prefer a uterine-sparing surgical option.

  6. Feasibility study for core protection calculator development

    International Nuclear Information System (INIS)

    In, W. K.; Han, J. B.

    2003-06-01

    This project confirmed the development feasibility of new digital core protection system and established development plan for ITOPS that can replace the CPC system. The development plan and implementation strategy for ITOPS proposed in this project will be useful to successfully develop advanced digital core protection system for the CPC replacement in KSNP plants. YGN units 3 and 4 are expected to replace the CPC system within next ten years and the other KSNP plants are followed. The localization model for advanced digital core protection system, ITOPS, is judged to upgrade the Common Q CPC system in both system configuration and algorithm performance and can reduce the cost for supply and maintenance. Hence, ITOPS is expected to be installed in new Korea nuclear power plants and also useful to export the associated technology in the future

  7. Case Study: Testing with Case Studies

    Science.gov (United States)

    Herreid, Clyde Freeman

    2015-01-01

    This column provides original articles on innovations in case study teaching, assessment of the method, as well as case studies with teaching notes. This month's issue discusses using case studies to test for knowledge or lessons learned.

  8. KELAYAKAN PEMANFAATAN LAHAN BEKAS TAMBANG BATUBARA UNTUK RELOKASI PERMUKIMAN PENDUDUK: STUDI KASUS AREAL TAMBANG PT. KITADIN (Feasibility of Former Coal-Mined Land for Resettlement A Case Study at PT. Kitadin

    Directory of Open Access Journals (Sweden)

    Retno Wuryandari

    2005-03-01

    Full Text Available ABSTRAK Penelitian ini bertujuan untuk mengevaluasi kelayakan tanah dan air di lahan penambangan batubara untuk area pemukiman. Penelitian di lakukan di daerah pertambangan batubara PT. Kitadin di kabupaten Kutai Kertanegara, provinsi Kalimantan Timur. Data untuk penelitian ini diperoleh dari survei lapangan dan sumber sekunder. Parameter yang dianalisis meliputi Soil Index Test, Grain Size Distribution, Density and Permeability. Parameter sample air meliputi pH, turbiditas, Total Dissolved Solid (TDS, Mangaan (Mn dan Besi (Fe. Data tersebut dibandingkan dengan kriteria penggunaan lahan untuk mengevaluasi kadar kelayakan/kesesuaian lahan. Hasil menunjukkan bahwa daerah penelitian tertutup lempung dengan plastisitas kurang dari 50%. Akumulasi air dalam lubang daerah penambangan batubara tidak masam dan memadai untuk konsumsi publik pada masa yang akan datang. Secara umum, daerah penelitian di pertambangan memadai untuk daerah permukiman.   ABSTRACT Conducted in PT. Kitadin coal-mined area which is located in Kutai Kartanegara Regency, East Kalimantan Timur Province, the research aimed to evaluate the feasibility conditions of soils and water at the coal-mined lands for settlement area. Data for the research were obtained from both field survey and secondary sources. The soil parameters analysed were Soil Index Test. Grain Size distribution, Density and Permeability. Water sample parameters analysed covered: pH, Turbidity, Total Dissolved Solid (TDS, Manganese (mn and Iron (Fe. The data were compared with land use criteria to evaluate land feasibility class. The results showed that the study area is covered by clay with its plasticity less than 50%. Meanwhile, the accumulated water in the hole of coal-mined area is not acid and adequate for future public consumption the future. Therefore, in general, the study area is considered appropriate and feasible for settlement.

  9. Preliminary feasibility study of modular reactors

    International Nuclear Information System (INIS)

    Yamaji, Kenji

    1987-01-01

    In the future, electric utilities will be required to make a switch-over to a more flexible and dynamic form of power supply due to the slowing growth of power demand, increasing uncertainty, the stagnating economy of increasing scale, the bottleneck of transmission and so on. Nuclear technology would also be required to adapt to this changing environment surrounding its development. The long term prospect of energy demand and nuclear power growth, and the evolution of commercial reactors in Japan are shown. The design of 1,300 MWe advanced LWRs has been completed, and as the reactors of next generation, the ultralarge LWRs of 1,500 - 1,800 MWe are suggested. However, there can be an alternative future for nuclear power development, and in this paper, the possibility for altering the image of conventional nuclear power technology by developing modular reactors which are economical even at small capacity, and can be sited in urban areas just like conventional thermal power plants is examined. The factors for the economical evaluation of modular reactors, learning effect and scale effect on the economy, the case study on a modular high temperature reactor designed by Interatom-GHT, and the possibility of siting in urban areas due to the system of inherent safety are reported. (Kako, I.)

  10. Do feasibility studies contribute to, or avoid, waste in research?

    Science.gov (United States)

    Morgan, Ben; Hejdenberg, Jennie; Hinrichs-Krapels, Saba; Armstrong, David

    2018-01-01

    In the context of avoiding research waste, the conduct of a feasibility study before a clinical trial should reduce the risk that further resources will be committed to a trial that is likely to 'fail'. However, there is little evidence indicating whether feasibility studies add to or reduce waste in research. Feasibility studies funded by the National Institute for Health Research's (NIHR) Research for Patient Benefit (RfPB) programme were examined to determine how many had published their findings, how many had applied for further funding for a full trial and the timeframe in which both of these occurred. A total of 120 feasibility studies which had closed by May 2016 were identified and each Principal Investigator (PI) was sent a questionnaire of which 89 responses were received and deemed suitable for analysis. Based on self reported answers from the PIs a total of 57 feasibility studies were judged as feasible, 20 were judged not feasible and for 12 it was judged as uncertain whether a full trial was feasible. The RfPB programme had spent approximately £19.5m on the 89 feasibility studies of which 16 further studies had been subsequently funded to a total of £16.8m. The 20 feasibility studies which were judged as not feasible potentially saved up to approximately £20m of further research funding which would likely to have not completed successfully. The average RfPB feasibility study took 31 months (range 18 to 48) to complete and cost £219,048 (range £72,031 to £326,830) and the average full trial funded from an RfPB feasibility study took 42 months (range 26 to 55) to complete and cost £1,163,996 (range £321,403 to £2,099,813). The average timeframe of feasibility study and full trial was 72 months (range 56 to 91), however in addition to this time an average of 10 months (range -7 to 29) was taken between the end of the feasibility study and the application for the full trial, and a further average of 18 months (range 13 to 28) between the

  11. FEASIBILITY STUDY OF SEDIMENT FLUSHING FROM MOSUL RESERVOIR, IRAQ

    Directory of Open Access Journals (Sweden)

    Thair Mahmood Al-Taiee

    2015-02-01

    Full Text Available The Feasibility of sediment flushing  from Mosul reservoir located northern iraq was conducted. Many up to date world criteria and indices for checking the efficiency of sediment flushing from reservoir which have been got through analyzing large amount of  data from many flushed reservoirs  in the world which were depended tested and applied in the present case study (Mosul Reservoir. These criteria and indices depend mainly on the hydrological , hydraulic and  topographical properties of the reservoirs in-addition to the operation plan of the reservoirs. They gave a good indication for checking the efficiency of the sediment flushing  process in the reservoirs. It was concluded that approximately the main criteria for the successful flushing sediment was  verified  in  Mosul  reservoir  such as  Sediment Balance Ratio   (SBR and the Long Term Capacity Ratio (LTCR,the shape factor  of reservoir (W/L and the hydraulic condition such as the percentage of (Qf/Qin and (Vf/Vin. This gave an indication that the processes of flushing sediment in Mosul reservoir is probably feasible and may be applied  in the future to maintain the water storage in the reservoir.

  12. Feasibility study of the AOSTA experimental campaign

    Directory of Open Access Journals (Sweden)

    Carta M.

    2016-01-01

    Full Text Available The reduction of the nuclear waste is one of the most important nuclear issues. The high radiotoxicity of the spent fuel is due to plutonium and some minor actinides (MAs such as neptunium, americium and curium, above all. One way to reduce their hazard is to destroy by fission MAs in appropriate nuclear reactors. To allow the MAs destruction an important effort have been done on the nuclear data due to the poor knowledge in this field. In the framework of one of the NEA Expert Group on Integral Experiments for Minor Actinide Management an analysis of the feasibility of MAs irradiation campaign in the TAPIRO fast research reactor is carried out. This paper provides preliminary results obtained by calculations modelling the irradiation, in different TAPIRO irradiation channels, of some CEA samples coming from the French experimental campaign OSMOSE, loaded with different contents of MAs, in order to access, through particular peak spectrometry, to their capture cross section. On the basis of neutron transport calculation results, obtained by both deterministic and Monte Carlo methods, an estimate of the irradiated samples counting levels from the AOSTA (Activation of OSMOSE Samples in TAPIRO experimental campaign is provided.

  13. Monitor of spatial plans. Feasibility study

    International Nuclear Information System (INIS)

    Bollen, M.J.S.; Ritsema van Eck, J.; Farjon, J.M.J.

    2008-01-01

    The national government needs assessments of consequences of building projects in relation to spatial policy objectives such as the prevention of urban sprawl or the development of landscape qualities. Normally the effects of spatial policies appear after several years. Spatial plans can possibly indicate these effects earlier. To allow policies to be adapted to unwanted developments, the assessments should be available in the early planning stages of these building projects. The Dutch Minister of VROM has asked the Netherlands Environmental Assessment Agency to investigate the feasibility of a monitoring system based on building plans. As building projects take a long period from conception until realization, a monitoring system for these projects should include all plans for the next ten to fifteen years with an indication of the chance that these plans are realized. The existing databases in the Netherlands provide sufficient information to assess consequences of plans for those objectives that are directly related to the urbanization pattern. However, an improvement of these databases is necessary, amongst other things by coordination of these databases [nl

  14. Sedimentary Geothermal Feasibility Study: October 2016

    Energy Technology Data Exchange (ETDEWEB)

    Augustine, Chad [National Renewable Energy Lab. (NREL), Golden, CO (United States); Zerpa, Luis [Colorado School of Mines, Golden, CO (United States)

    2017-01-01

    The objective of this project is to analyze the feasibility of commercial geothermal projects using numerical reservoir simulation, considering a sedimentary reservoir with low permeability that requires productivity enhancement. A commercial thermal reservoir simulator (STARS, from Computer Modeling Group, CMG) is used in this work for numerical modeling. In the first stage of this project (FY14), a hypothetical numerical reservoir model was developed, and validated against an analytical solution. The following model parameters were considered to obtain an acceptable match between the numerical and analytical solutions: grid block size, time step and reservoir areal dimensions; the latter related to boundary effects on the numerical solution. Systematic model runs showed that insufficient grid sizing generates numerical dispersion that causes the numerical model to underestimate the thermal breakthrough time compared to the analytic model. As grid sizing is decreased, the model results converge on a solution. Likewise, insufficient reservoir model area introduces boundary effects in the numerical solution that cause the model results to differ from the analytical solution.

  15. Pilot Feasibility Study of an Oncology Financial Navigation Program.

    Science.gov (United States)

    Shankaran, Veena; Leahy, Tony; Steelquist, Jordan; Watabayashi, Kate; Linden, Hannah; Ramsey, Scott; Schwartz, Naomi; Kreizenbeck, Karma; Nelson, Judy; Balch, Alan; Singleton, Erin; Gallagher, Kathleen; Overstreet, Karen

    2018-02-01

    Few studies have reported on interventions to alleviate financial toxicity in patients with cancer. We developed a financial navigation program in collaboration with our partners, Consumer Education and Training Services (CENTS) and Patient Advocate Foundation (PAF), to improve patient knowledge about treatment costs, provide financial counseling, and to help manage out-of-pocket expenses. We conducted a pilot study to assess the feasibility and impact of this program. Patients with cancer received a financial education course followed by monthly contact with a CENTS financial counselor and a PAF case manager for 6 months. We measured program adherence, self-reported financial burden and anxiety, program satisfaction, and type of assistance provided. Thirty-four patients (median age, 60.5 years) were consented (85% white and 50% commercially insured). Debt, income declines, and loans were reported by 55%, 55%, and 30% of patients, respectively. CENTS counselors assisted most often with budgeting, retirement planning, and medical bill questions. PAF case managers assisted with applications for appropriate insurance coverage, cost of living issues (eg, housing, transportation), and disability applications. High financial burden and anxiety about costs (4 or 5 on a Likert scale) were reported at baseline by 37% and 47% of patients, respectively. Anxiety about costs decreased over time in 33% of patients, whereas self-reported financial burden did not substantially change. Implementing an oncology financial navigation program is feasible, provides concrete assistance in navigating the cost of care, and mitigates anxiety about costs in a subset of patients. Future work will focus on measuring the program's impact on financial and clinical outcomes.

  16. Washoe Tribe Alternative Energy Feasibility Study Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Jennifer [Washoe Tribe of NV and CA

    2014-10-01

    The Washoe Tribe of Nevada and California was awarded funding to complete the Washoe Tribe Alternative Energy Feasibility Study project. The main goal of the project was to complete an alternative energy feasibility study. This study was completed to evaluate “the potential for development of a variety of renewable energy projects and to conduct an alternative energy feasibility study that determines which alternative energy resources have the greatest economic opportunity for the Tribe, while respecting cultural and environmental values” (Baker-Tilly, 2014). The study concluded that distributed generation solar projects are the best option for renewable energy development and asset ownership for the Washoe Tribe. Concentrating solar projects, utility scale wind projects, geothermal, and biomass resource projects were also evaluated during the study and it was determined that these alternatives would not be feasible at this time.

  17. Radiation processing of flue gases: Guidelines for feasibility studies

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    The aim of this publication is to facilitate the performance of feasibility studies for Electron Beam flue gas cleanup projects by providing guidelines to conduct these studies and compiling information on the state of the art. This document summarizes the contents of a feasibility study; discusses the main items in plant construction, measurement and control systems, radiation safety and building construction; and lists the required economic data for internationally funded projects.

  18. Radiation processing of flue gases: Guidelines for feasibility studies

    International Nuclear Information System (INIS)

    2000-12-01

    The aim of this publication is to facilitate the performance of feasibility studies for Electron Beam flue gas cleanup projects by providing guidelines to conduct these studies and compiling information on the state of the art. This document summarizes the contents of a feasibility study; discusses the main items in plant construction, measurement and control systems, radiation safety and building construction; and lists the required economic data for internationally funded projects

  19. Nasal Unit Transplantation: A Cadaveric Anatomical Feasibility Study.

    Science.gov (United States)

    Dorafshar, Amir H; Mundinger, Gerhard S; Robinson, Brent; Tuffaha, Sami; Brandacher, Gerald; Byrne, Patrick; Walton, Robert L

    2017-05-01

    Background  The science and technical acumen in the field of vascularized composite allotransplantation has progressed rapidly over the past 15 years, and transplantation of specialized units of the face, such as the nose, appears possible. No study to date has evaluated the technical feasibility of isolated nasal unit transplantation (NUT). In this study, we explore the anatomy and technical specifics of NUT. Methods  In this study, four fresh cadaver heads were studied. Bilateral vascular pedicle dissections were performed in each cadaver. The facial artery was cannulated and injected with food dye under physiologic pressure in two cadavers, and with lead oxide mixture in two cadavers to evaluate perfusion territories supplied by each vascular pedicle. Results  The facial artery and vein were found to be adequate pedicles for NUT. Divergent courses of the vein and artery were consistently identified, which made for a bulky pedicle with necessary inclusion of large amounts of subcutaneous tissue. In all cases, the artery remained superficial, while the vein coursed in a deeper plane, and demonstrated consistent anastomoses with the superior transverse orbital arcade. While zinc oxide injection of the facial artery demonstrated filling of the nasal vasculature across the midline, dye perfusion studies suggested that unilateral arterial inflow may be insufficient to perfuse contralateral NUT components. Discrepancies in these two studies underscore the limitations of nondynamic assessment of nutritive perfusion. Conclusion  NUT based on the facial artery and facial vein is technically feasible. Angiosome evaluation suggests that bilateral pedicle anastomoses may be required to ensure optimal perfusion. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

  20. Feasibility Study: New Knowledge Demands in Turbulent Business World

    Science.gov (United States)

    Sprice, Renate; Kirikova, Marite

    Feasibility study is one of the early activities in information systems (IS) development when important decisions regarding choice among several possible systems development alternatives are to be made. In times of relatively stable business environment and waterfall model as a systems development approach, the role and methods of feasibility study where quite clear (Kendall and Kendall 1995). However, new software development methods and the necessity to develop more rapidly new IS or their parts may. challenge the possibility to evaluate project feasibility in the early stages of IS development.

  1. A feasibility study of bridge deck deicing using geothermal energy.

    Science.gov (United States)

    2015-04-01

    In this study, we investigated the feasibility of a ground-coupled system that utilizes heat energy harvested from the ground for : deicing of bridge decks. Heat exchange is performed using circulation loops integrated into the deep foundations suppo...

  2. Optical Coherence Tomography of the Breast: A Feasibility Study

    National Research Council Canada - National Science Library

    Connolly, James

    2003-01-01

    .... This novel imaging technology has the potential to improve cancer detection and diagnosis. The aim of this study was to determine the feasibility of applying OCT imaging to normal and pathologic human breast tissue, as well as other human tissues...

  3. Optical Coherence Tomography of the Breast: A Feasibility Study

    National Research Council Canada - National Science Library

    Connolly, James L

    2005-01-01

    .... This novel imaging technology has the potential to improve cancer detection and diagnosis. The aim of this study was to determine the feasibility of applying OCT imaging to normal and pathologic human breast tissue, as well as other human tissues...

  4. MacMillan Pier Transportation Center Feasibility Study.

    Science.gov (United States)

    2006-06-01

    The MacMillan Pier Transportation Center Feasibility Study examines two potential sites (landside and waterside) for a transportation center that provides a range of tourist and traveler information. It would serve as a gateway for Provincetown and t...

  5. Final Report: Feasibility Study of Biomass in Snohomish County, Washington

    Energy Technology Data Exchange (ETDEWEB)

    Daryl Williams (Tulalip Tribes); Ray Clark (Clark Group)

    2005-01-31

    This report and its attachments summarizes the results of a unique tribal-farmer cooperative study to evaluate the feasibility of building one or more regional anaerobic digestion systems in Snohomish County, Washington.

  6. Feasibility of thoracoscopic approach for retrosternal goitre (posterior mediastinal goitre: Personal experiences of 11 cases

    Directory of Open Access Journals (Sweden)

    Panchangam Ramakanth Bhargav

    2016-01-01

    Full Text Available Introduction: Posterior mediastinal goitres constitute of a unique surgical thyroid disorder that requires expert management. Occasionally, they require thoracic approach for the completion of thyroidectomy. In this paper, we describe the feasibility and utility of a novel thoracoscopic approach for such goitres. Materials and Methods: This is a retrospective study conducted at a tertiary care endocrine surgery department in South India over a period of 5 years from January 2010 to December 2014. We developed a novel thoracoscopic technique for posterior mediastinal goitres instead of a more morbid thoracotomy or sternotomy. All the clinical, investigative, operative, pathological and follow-up data were collected from our prospectively filled database. Statistical analysis was done with SPSS 15.0 version. Descriptive analysis was done. Operative Technique of Thoracoscopic Thyroidectomy: Single lumen endotracheal tube (SLETT was used of anaesthetic intubation and general inhalational anaesthesia. Operative decubitus was supine with extension and abduction of the ipsilateral arm. Access to mediastinum was obtained by two working ports in the third and fifth intercostal spaces. Mediastinal extension was dissected thoracoscopically and delivered cervically. Results: Out of 1,446 surgical goitres operated during the study period, 72 (5% had retrosternal goitre. Also, 27/72 (37.5% cases had posterior mediastinal extension (PME, out of which 11 cases required thoracic approach. We utilised thoracoscopic technique for these 11 cases. The post-operative course was uneventful with no major morbidity. There was one case of recurrent laryngeal nerve (RLN injury and hoarseness of voice in the third case. Histopathologies in 10 cases were benign, out of which two had subclinical hyperthyroidism. One case had multifocal papillary microcarcinoma. Conclusions: We opine that novel thoracoscopic technique is a feasibly optimal approach for posterior mediastinal

  7. Ute Mountain Ute Tribe Community-Scale Solar Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Rapp, Jim [Parametrix; Knight, Tawnie [Ute Mountain Ute Tribe

    2014-01-30

    Parametrix Inc. conducted a feasibility study for the Ute Mountain Ute Tribe to determine whether or not a community-scale solar farm would be feasible for the community. The important part of the study was to find where the best fit for the solar farm could be. In the end, a 3MW community-scale solar farm was found best fit with the location of two hayfield sites.

  8. Feasibility study on the acquisition of licensee event data

    International Nuclear Information System (INIS)

    Kato, W.Y.; Hall, R.E.; Teichmann, T.; Taylor, J.; Luckas, W.J. Jr.; Saha, P.; Samanta, P.; Fragola, J.

    1983-01-01

    Objective of the study was to assess the feasibility of modifying the LER reporting system as proposed by NRC-AEOD, and/or developing an alternative plan that would in addition collect information about significant events amenable to statistical analysis, such as multi-case, multi-variate analysis. The study indicated that the LERs constitute reports from a large variety of events which have in most cases many different plant parameters, both measured and currently not measured, to characterize the event. In order to determine event-specific plant parameters required for statistical and deterministic analysis, a data matrix approach was used to identify those parameters which are currently being recorded, those which could be measured and recorded, and those which are required for certain types of events involving thermal-hydraulics and neutronics as illustrative of events requiring in-depth analysis. Also included in the study was a review of INPO's Nuclear Plant Reliability Data System; NASA's Problem Reporting and Corrective Action (PRACA) program; Electricite de France's KIT system, an automatic computer-based reactor parameter monitoring and recording system; and the regulatory relationship between the FAA and the commercial airline industry

  9. Feasibility Study of Alternative Fabrication Methods.

    Science.gov (United States)

    1979-08-01

    must comply with the I requirements of the latest edition of the National Electrical Code. The Body and Liner Assembly System will comply with I the...latest edition of the National Electrical Code per AMCR 385 (Army Material Command Safety Manual). Also, OSHA’s 1 Occupational Safety and Health...the top of the elevator. On the top and at the rear of * A-4 50 UD( AISA 6 --7 G OVe CASE THOMS ’ON J .7O37IA (PLACES) _ _ -- 3. BAL - 1N-TOS10 12N

  10. Direct solar pumping of semiconductor lasers: A feasibility study

    Science.gov (United States)

    Anderson, Neal G.

    1992-01-01

    This report describes results of NASA Grant NAG-1-1148, entitled Direct Solar Pumping of Semiconductor Lasers: A Feasibility Study. The goals of this study were to provide a preliminary assessment of the feasibility of pumping semiconductor lasers in space with directly focused sunlight and to identify semiconductor laser structures expected to operate at the lowest possible focusing intensities. It should be emphasized that the structures under consideration would provide direct optical-to-optical conversion of sunlight into laser light in a single crystal, in contrast to a configuration consisting of a solar cell or storage battery electrically pumping a current injection laser. With external modulation, such lasers could perhaps be efficient sources for intersatellite communications. We proposed specifically to develop a theoretical model of semiconductor quantum-well lasers photopumped by a broadband source, test it against existing experimental data where possible, and apply it to estimating solar pumping requirements and identifying optimum structures for operation at low pump intensities. These tasks have been accomplished, as described in this report of our completed project. The report is organized as follows: Some general considerations relevant to the solar-pumped semiconductor laser problem are discussed in Section 2, and the types of structures chosen for specific investigation are described. The details of the laser model we developed for this work are then outlined in Section 3. In Section 4, results of our study are presented, including designs for optimum lattice-matched and strained-layer solar-pumped quantum-well lasers and threshold pumping estimates for these structures. It was hoped at the outset of this work that structures could be identified which could be expected to operate continuously at solar photoexcitation intensities of several thousand suns, and this indeed turned out to be the case as described in this section. Our project is

  11. Feasibility study: Assess the feasibility of siting a monitored retrievable storage facility

    International Nuclear Information System (INIS)

    King, J.W.

    1993-01-01

    The purpose of phase one of this study are: To understand the waste management system and a monitored retrievable storage facility; and to determine whether the applicant has real interest in pursuing the feasibility assessment process. Contents of this report are: Generating electric power; facts about exposure to radiation; handling storage, and transportation techniques; description of a proposed monitored retrievable storage facility; and benefits to be received by host jurisdiction

  12. Feasibility study: Assess the feasibility of siting a monitored retrievable storage facility. Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    King, J.W.

    1993-08-01

    The purpose of phase one of this study are: To understand the waste management system and a monitored retrievable storage facility; and to determine whether the applicant has real interest in pursuing the feasibility assessment process. Contents of this report are: Generating electric power; facts about exposure to radiation; handling storage, and transportation techniques; description of a proposed monitored retrievable storage facility; and benefits to be received by host jurisdiction.

  13. Large Deployable Reflector (LDR) feasibility study update

    Science.gov (United States)

    Alff, W. H.; Banderman, L. W.

    1983-01-01

    In 1982 a workshop was held to refine the science rationale for large deployable reflectors (LDR) and develop technology requirements that support the science rationale. At the end of the workshop, a set of LDR consensus systems requirements was established. The subject study was undertaken to update the initial LDR study using the new systems requirements. The study included mirror materials selection and configuration, thermal analysis, structural concept definition and analysis, dynamic control analysis and recommendations for further study. The primary emphasis was on the dynamic controls requirements and the sophistication of the controls system needed to meet LDR performance goals.

  14. Verifying FreeRTOS; a feasibility study

    NARCIS (Netherlands)

    Pronk, C.

    2010-01-01

    This paper presents a study on modeling and verifying the kernel of Real-Time Operating Systems (RTOS). The study will show advances in formally verifying such an RTOS both by refinement and by model checking approaches. This work fits in the context of Hoare’s verification challenge. Several

  15. BNL feasibility studies of spallation neutron sources

    International Nuclear Information System (INIS)

    Lee, Y.Y.; Ruggiero, A.G.; Van Steenbergen, A.; Weng, W.T.

    1995-01-01

    This paper is the summary of conceptual design studies of a 5 MW Pulsed Spallation Neutron Source (PSNS) conducted by an interdepartmental study group at Brookhaven National Laboratory. The study was made of two periods. First, a scenario based on the use of a 600 MeV Linac followed by two fast-cycling 3.6 GeV Synchrotrons was investigated. Then, in a subsequent period, the attention of the study was directed toward an Accumulator scenario with two options: (1) a 1.25 GeV normal conducting Linac followed by two Accumulator Rings, and (2) a 2.4 GeV superconducting Linac followed by a single Accumulator Ring. The study did not make any reference to a specific site

  16. Wind Generation Feasibility Study in Bethel, AK

    Energy Technology Data Exchange (ETDEWEB)

    Tom Humphrey, YKHC; Lance Kincaid, EMCOR Energy & Technologies

    2004-07-31

    This report studies the wind resources in the Yukon-Kuskokwim Health Corporation (YKHC) region, located in southwestern Alaska, and the applicability of wind generation technologies to YKHC facilities.

  17. Proof of feasibility of the through casing resistivity technology

    Energy Technology Data Exchange (ETDEWEB)

    Vail, Dr. W. Banning; Momii, Steven T.

    2000-06-21

    This project is to definitely prove that the resistivity of geological formations can be measured from within cased wells and to license the relevant patents and technology to major wireline service companies.

  18. CASE STUDY CRITIQUE; UPPER CLINCH CASE STUDY

    Science.gov (United States)

    Case study critique: Upper Clinch case study (from Research on Methods for Integrating Ecological Economics and Ecological Risk Assessment: A Trade-off Weighted Index Approach to Integrating Economics and Ecological Risk Assessment). This critique answers the questions: 1) does ...

  19. Technical feasibility study of Voltage Optimization Unit

    DEFF Research Database (Denmark)

    Hu, Junjie; Marinelli, Mattia; Coppo, Massimiliano

    This report provides an analysis on the benefits of a transformer with on load tap chang-ers on each phase that can be applied in the distribution system to accommodate more renewable generations such as photovoltaic power. The main purpose of this research is to verify whether power distribution...... are used as load basics for the analysis. In term of PV genera-tion profiles, a realistic PV output power is assumed. Four relevant indicies such as phase neutral voltage, netural potential voltage, unbalanced factor (VUF), and power losses are evaluated in the present study. The simulation tests include...

  20. Feasibility studies for GPD's measurement at COMPASS

    CERN Document Server

    Marroncle, J

    2004-01-01

    Deeply Virtual Compton Scattering is a clean way to access the Generalized Parton Distributions of the proton. This paper deals with a possibility to perform such an experiment with the COMPASS apparatus which allows to access a large rang in $x_{Bj}$(0.03 to 0.25) and $Q^{2}$(1.5 to 7.5 GeV$^{2}$). A possible design for a recoil detector which is necessary to complement the COMPASS setup, is presented. Preliminary results on exclusive $]rho^{0}$ production from the COMPASS 2002 run are given. They look promising for future studies of deep $\\rho^{0}$ production.

  1. Mined salt storage feasibility: Engineering study report

    International Nuclear Information System (INIS)

    1987-07-01

    This study addresses a method of eliminating the surface storage of mined salt at the Deaf Smith repository site. It provides rough estimates of the logistics and costs of transporting 3.7 million tons of salt from the repository to the salt disposal site near Carlsbad, New Mexico and returning it to the repository for decommissioning backfill. The study assumes that a railcar/truck system will be installed and that the excavated salt will be transported from the repository to an existing potash mine located near Carlsbad, New Mexico approximately 300 miles from the repository. The 3.7 million tons of salt required for repository decommissioning backfill can be stored in the potash mines along with the excess salt, with no additional capital costs required for either a railcar or a truck transportation system. The capital cost for facilities to reclaim the 3.7 million tons of salt from the potash mine is estimated to be $4,400,000 with either a rail or truck transportation system. Segregating the 3.7 million tons of backfill salt in a surface storage area at the potash mine requires a capital cost of $13,900,000 with a rail system or $11,400,000 with a truck system. Transportation costs are estimated at $0.08/ton-mile for rail and $0.13/ton-mile for truck. 2 figs., 5 tabs

  2. High Falls Hydroelectric Plant feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Diezemann, Gustav A.

    1979-07-01

    This study was made in order to determine if re-activating the retired High Falls Hydro Station in New York would result in a more economical generation of some of the power required in the Central Hudson System than is being obtained with the oil-burning thermal plants. The findings show that the construction of a new plant is more economical than rehabilitation of the existing station. All new construction schemes are marginally unattractive at today's costs but are found to become profitable within a short period as alternative energy sources escalate in price. A new powerhouse with an installed capacity of 2390 kW proved most economical, and its construction is recommended.

  3. Nuclear Aircraft Feasibility Study. Volume 1

    Science.gov (United States)

    1975-03-01

    Iso Dose 10-12 10.1.4-3 Absorption Cross Section Ratio 10-14 10.1.5-1 Engine Systems Study Diagram 10-15 10.1.8-1 Life Cycle Cost for 60...0 00 ■ 3 15.00 OC z ^ 10.00 X s -i 1 UJ 5 < oc D I 50.00 40.00 30.00 20.00 1 ’ ISO LBS/SQ FT WING...4.1.6-1. Payload vs Wing Loading 4-17 m I - 27000 | i i ^1 ̂ N GROSS WEIGHT > 1.600,000 LBS 523 FT/SEC P 30.000 FT ONE GAS REACTOR 1

  4. A biodegradable vascularizing membrane: a feasibility study.

    Science.gov (United States)

    Kaushiva, Anchal; Turzhitsky, Vladimir M; Darmoc, Marissa; Backman, Vadim; Ameer, Guillermo A

    2007-09-01

    Regenerative medicine and in vivo biosensor applications require the formation of mature vascular networks for long-term success. This study investigated whether biodegradable porous membranes could induce the formation of a vascularized fibrous capsule and, if so, the effect of degradation kinetics on neovascularization. Poly(l-lactic acid) (PLLA) and poly(dl-lactic-co-glycolic) acid (PLGA) membranes were created by a solvent casting/salt leaching method. Specifically, PLLA, PLGA 75:25 and PLGA 50:50 polymers were used to vary degradation kinetics. The membranes were designed to have an average 60mum pore diameter, as this pore size has been shown to be optimal for inducing blood vessel formation around nondegradable polymer materials. Membrane samples were imaged by scanning electron microscopy at several time points during in vitro degradation to assess any changes in pore structure. The in vivo performance of the membranes was assessed in Sprague-Dawley rats by measuring vascularization within the fibrous capsule that forms adjacent to implants. The vascular density within 100microm of the membranes was compared with that seen in normal tissue, and to that surrounding the commercially available vascularizing membrane TheraCyte. The hemoglobin content of tissue containing the membranes was measured by four-dimensional elastic light scattering as a novel method to assess tissue perfusion. Results from this study show that slow-degrading membranes induce greater amounts of neovascularization and a thinner fibrous capsule relative to fast degrading membranes. These results may be due both to an initially increased number of macrophages surrounding the slower degrading membranes and to the maintenance of their initial pore structure.

  5. Feasibility study of EEW application in Korea

    Science.gov (United States)

    Chi, H.; Park, J.; Sheen, D.

    2008-12-01

    At present, it seems almost impossible to predict where and how much strong a earthquake will happen within very limited time such as two or three days before it occurs. However, the advantage of modern electronic techniques can support us very fast communication tools around nation-wide area so that we can receive P- waves arrival information from seismic stations through communication lines before S-waves strike our living site. This is the key of EEW(Earthquake Early Warning) concept that is under development around world especially including Japan, United State of America, and Taiwan. In this pilot study we proposed the direction for developing Korean Earthquake Early Warning System. Considering the state of the art techniques used in Japan, USA and Taiwan, ElarmS would be more adaptable to Korea since ElarmS can work from the low limit of moderate earthquakes around magnitude 3.5, which would annually happen in Korea. We investigate empirical magnitude scaling relationship for South Korea using 27 events ranging in magnitude from 2.2 to 4.9 recorded by the Korea Institute of Geoscience And Mineral Resources (KIGAM) and the Korea Meteorological Administration (KMA) for 2007. We measure the maximum predominant period and the peak displacement or velocity amplitude from the first 4 seconds of P wave arrivals to derive period-magnitude and amplitude-magnitude scaling relationship, respectively. For the period-magnitude relationship, we find that 10 Hz low-pass filter yields better estimate than 3 Hz. This is because the magnitudes of most events used in this study are too small (<3.0). It is also shown that peak displacement for velocity instruments and peak velocity for accelerometers have their own magnitude scaling relationships, respectively. Thus, for the amplitude-magnitude relationship, like the relationships in northern California, two individual amplitude scaling relationships would be necessary.

  6. Feasibility study of CT perfusion imaging for prostate carcinoma

    International Nuclear Information System (INIS)

    Cullu, Nesat; Kantarci, Mecit; Ogul, Hayri; Pirimoglu, Berhan; Karaca, Leyla; Kizrak, Yesim; Adanur, Senol; Koc, Erdem; Polat, Ozkan; Okur, Aylin

    2014-01-01

    The aim of this feasibility study was to obtain initial data with which to assess the efficiency of perfusion CT imaging (CTpI) and to compare this with magnetic resonance imaging (MRI) in the diagnosis of prostate carcinoma. This prospective study involved 25 patients with prostate carcinoma undergoing MRI and CTpI. All analyses were performed on T2-weighted images (T2WI), apparent diffusion coefficient (ADC) maps, diffusion-weighted images (DWI) and CTp images. We compared the performance of T2WI combined with DWI and CTp alone. The study was approved by the local ethics committee, and written informed consent was obtained from all patients. Tumours were present in 87 areas according to the histopathological results. The diagnostic performance of the T2WI+DWI+CTpI combination was significantly better than that of T2WI alone for prostate carcinoma (P < 0.001). The diagnostic value of CTpI was similar to that of T2WI+DWI in combination. There were statistically significant differences in the blood flow and permeability surface values between prostate carcinoma and background prostate on CTp images. CTp may be a valuable tool for detecting prostate carcinoma and may be preferred in cases where MRI is contraindicated. If this technique is combined with T2WI and DWI, its diagnostic value is enhanced. (orig.)

  7. CsIX/TRU Grout Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    S. J. Losinski; C. M. Barnes; B. K. Grover

    1998-11-01

    A settlement agreement between the Department of Energy (DOE) and the State of Idaho mandates that liquid waste now stored at the Idaho Nuclear Technology Engineering Center (INTEC - formerly the Idaho Chemical Processing Plant, ICPP) will be calcined by the end of year 2012. This study investigates an alternative treatment of the liquid waste that removes undissolved solids (UDS) by filtration and removes cesium by ion exchange followed by cement-based grouting of the remaining liquid into 55-gal drums. Operations are assumed to be from January 2008 through December 2012. The grouted waste will be contact-handled and will be shipped to the Waste Isolation Pilot Plant (WIPP) in New Mexico for disposal. The small volume of secondary wastes such as the filtered solids and cesium sorbent (resin) would remain in storage at the Idaho National Engineering and Environmental Laboratory for treatment and disposal under another project, with an option to dispose of the filtered solids as a r emote-handled waste at WIPP.

  8. CsIX/TRU Grout Feasibility Study

    International Nuclear Information System (INIS)

    Losinski, S. J.; Barnes, C. M.; Grover, B. K.

    1998-01-01

    A settlement agreement between the Department of Energy (DOE) and the State of Idaho mandates that liquid waste now stored at the Idaho Nuclear Technology Engineering Center (INTEC - formerly the Idaho Chemical Processing Plant, ICPP) will be calcined by the end of year 2012. This study investigates an alternative treatment of the liquid waste that removes undissolved solids (UDS) by filtration and removes cesium by ion exchange followed by cement-based grouting of the remaining liquid into 55-gal drums. Operations are assumed to be FR-om January 2008 through December 2012. The grouted waste will be contact-handled and will be shipped to the Waste Isolation Pilot Plant (WIPP) in New Mexico for disposal. The small volume of secondary wastes such as the filtered solids and cesium sorbent (resin) would remain in storage at the Idaho National Engineering and Environmental Laboratory for treatment and disposal under another project, with an option to dispose of the filtered solids as a r emote-handled waste at WIPP

  9. [Cambridge Conference on School Mathematics Feasibility Studies 9-13.

    Science.gov (United States)

    Cambridge Conference on School Mathematics, Newton, MA.

    These materials are a part of a series of studies sponsored by the Cambridge Conference on School Mathematics which reflects the ideas of CCSM regarding the goals and objectives for school mathematics K-12. Feasibility Studies 9-13 contain a wide range of topics. The following are the titles and brief descriptions of these studies. Number…

  10. Restoring effective sleep tranquility (REST): A feasibility and pilot study.

    Science.gov (United States)

    Eakman, Aaron M; Schmid, Arlene A; Henry, Kimberly L; Rolle, Natalie R; Schelly, Catherine; Pott, Christine E; Burns, Joshua E

    2017-06-01

    The purpose of this pilot study was to establish the feasibility of completing a future controlled trial of a multi-component cognitive behavioral therapy for insomnia program for military veterans with sleep disturbance. This was a single-arm feasibility and pilot study. Participants were United States post-9/11 veterans with service-connected injuries, university students, and had self-reported sleep disturbances. Restoring Effective Sleep Tranquility was a multi-component cognitive behavioral therapy for insomnia intervention consisting of seven sessions of group therapy and eight 1:1 sessions delivered by occupational therapists. Feasibility and pilot indicators were process, resources, management, and scientific, including pre-post-assessments of sleep difficulties, dysfunctional sleep beliefs, participation, and pain interference. Indicators were supportive of feasibility, including reduced sleep difficulties (for example Medical Outcomes Study Sleep Measure [ t  = 3.29, p  = .02]), reduced nightmares: t  = 2.79, p  = .03; fewer dysfunctional sleep beliefs: t  = 3.63, p  = .01, and greater ability to participate in social roles: t  = -2.86, p  = .03, along with trends towards improved satisfaction with participation and reduced pain interference. The Restoring Effective Sleep Tranquility program may reduce sleep difficulties and improve participation in US veterans with service-connected injuries, and evidence indicates a controlled trial would be feasible to deliver.

  11. The environmental energy sector programme. Poland: Feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    The Danish Ministry of Energy has granted financial aid to the preparation of a feasibility study necessary for the procurement of a financial solution to the modernisation of the combined heat and power plant in the city of Zielona Gora.The overall objectives of the Feasibility Study are to: establish new efficient power capacity in the south-west region of Poland, increase the energy efficiency, reduce the impact on the environment, utilise the local natural gas available which cannot be used in the national gas grid and reduce the costs of energy supply.The specific objective of this feasibility study is to obtain the best possible financing of the erection of a new CPH plant in Zielona Gora. The plant shall be designed to utilise the local resources of natural gas and to supply heat to the district heating grid in accordance with long-term planning strategies. (EHS)

  12. Feasibility Study and Optimization of An Hybrid System (Eolian ...

    African Journals Online (AJOL)

    Feasibility Study and Optimization of An Hybrid System (Eolian- Photovoltaic - Diesel) With Provision of Electric Energy Completely Independent. ... reducing emissions of greenhouse gas (CO2 rate = 16086 kg / year for a system using only the generator diesel and is 599 kg / year for the stand alone hybrid system studied).

  13. Istra district heating system. Master plan and feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-01

    This report presents the results of the Feasibility Study of options for improving the efficiency and operating economy of Istra Large-Scale Demonstration Project includes all areas of the town of Istra. However, the Feasibility Study is confined to the five largest adjoining boilers plant areas within the borders of Istra town. The study was conducted from 1999 to 2001 and was based on information collected during this period. The city administration and the district heating company in Istra provided the data. The company RDIEE, Russian Danish Institute for Energy Efficiency, in Istra collected and processed the data under the conduction of Carl Bro a/s in Denmark. The main objectives of the study are to provide the Istra DHC with a number of options for future development of the district heating system based on technical/financial analyses and presenting the best possibilities for improved comfort, operation and business development. More concretely, one or more system improvement scenarios, which can be implemented in the near future as a first step of the recommended medium-term to long-term development, are identified. Another important objective has been to train the specialists of RDIEE in the feasibility study process and to transfer know-how, skills and tools. The model used for this study is adapted to the features and the special problems to be addressed in relation to the Istra district heating system. RDIEE and Istra DHC are thereby provided with a useful tool which may be used for continued study and development after the first phase project has been completed. As usual in the case of input/output models the quality of the results depends very much on the quality of input data. The present report is exclusively based on the consultant's understanding of the provided information. The results and the underlying inputs should be carefully considered before any final decision concerning implementation is taken. Verification of assumptions should also

  14. Case series of feasibility considerations that impact operational delivery strategy in the highly competitive rheumatoid arthritis space in Asia

    Directory of Open Access Journals (Sweden)

    Wai K

    2013-02-01

    Full Text Available Karen Wai,1 Lisa Marie Saldanha,1 Elvira Zenaida Lansang,1 Saumya Nayak,1 Anish Sule,2 Ken J Lee31Feasibility and Site Identification Asia, Quintiles East Asia Pte Ltd, Singapore; 2Feasibility and Site Identification India, Quintiles India, Mumbai, India; 3Site Services Asia, Quintiles East Asia Pte Ltd, SingaporeAbstract: The rheumatoid arthritis (RA clinical trial space is very competitive, and recruiting and retaining subjects is of critical importance. Feasibility studies are a central component of ensuring successful recruitment and retention. A feasibility study is an assessment of the practicality of a proposed study protocol, with the goal of understanding challenges and providing risk mitigation strategies leading to better subject enrolment and study start-up should the assessment be favorable. This paper presents findings from a retrospective case series of RA feasibilities, describing important parameters to consider in the highly competitive RA space in Asia. Key parameters identified and discussed are how decisions on clinical development strategy necessitate changes in the clinical operational delivery strategy, with focus on changes in inclusion and exclusion criteria and patient contribution load; how small the patient population becomes when the clinical trial needs to target the patient population that is refractory to standard therapy; regulatory timelines; and the competitive clinical trial landscape. Feasibility assessments are a snapshot in time exercise. Multiple parameters change over time, and, particularly in a space that has become competitive for subjects, one cannot rely on one static feasibility assessment to predict trial performance accurately. Continuous feasibility assessment will also provide insight into the resourcing needs on the part of the sponsor, contract research organization, and investigative site.Keywords: site selection, country selection, clinical operations, risk management, recruitment rates

  15. Feasibility study for the spallation neutron source (SNQ). Pt. 1

    International Nuclear Information System (INIS)

    Bauer, G.S.; Sebening, H.; Vetter, J.E.; Willax, H.

    1981-06-01

    A concept for a new neutron source for fundamental research has been developed and is described in this report. The spallation neutron source SNQ is characterized in its first stage by a time average thermal neutron flux of 7 x 10 14 cm -2 s -1 and a peak flux of 1.3 x 10 16 cm -2 s -1 at 100 Hz repetition rate. The scientific case is presented with particular emphasis on solid state and nuclear physics. In these research domains, unique conditions are given for experimental use. The proposed machine consists in its basic stage of a 1.1 GeV, 5 mA time average, 100 mA peak current proton linear accelerator, a rotating lead target, and H 2 O and D 2 O moderators. Additional beam channels are provided for experiments with protons at 350 MeV and at the final energy. Construction of the SNQ is considered feasible within eight years at a cost of 680 million DM. As future options, use of uranium as a target material, increase of the accelerator beam power by a factor of 2, addition of a pulse compressor and a second target station for pulsed neutron and neutrino research are described. As a back-up solution to the rotating target, a liquid metal target was studied. (orig.) [de

  16. Front Range Forest Health Partnership Phase 1 feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Volkin, P

    1998-09-01

    The Front Range Forest Health Partnership is an alliance of individuals, citizen groups, federal, state, private, and nonprofit organizations that formed to promote forest health restoration and reduce fire risks on Colorado's Front Range. The partnership promotes selective thinning to restore forest health and supports economically feasible end uses for wood waste materials. The Phase I study was initiated to determine the environmental and economic feasibility of using wood wastes from forested and urban areas for the production of fuel-grade ethanol.

  17. Deschutes estuary feasibility study: hydrodynamics and sediment transport modeling

    Science.gov (United States)

    George, Douglas A.; Gelfenbaum, Guy; Lesser, Giles; Stevens, Andrew W.

    2006-01-01

    Continual sediment accumulation in Capitol Lake since the damming of the Deschutes River in 1951 has altered the initial morphology of the basin. As part of the Deschutes River Estuary Feasibility Study (DEFS), the United States Geological Survey (USGS) was tasked to model how tidal and storm processes will influence the river, lake and lower Budd Inlet should estuary restoration occur. Understanding these mechanisms will assist in developing a scientifically sound assessment on the feasibility of restoring the estuary. The goals of the DEFS are as follows. - Increase understanding of the estuary alternative to the same level as managing the lake environment.

  18. Feasibility study of full-reactor gas core demonstration test

    Science.gov (United States)

    Kunze, J. F.; Lofthouse, J. H.; Shaffer, C. J.; Macbeth, P. J.

    1973-01-01

    Separate studies of nuclear criticality, flow patterns, and thermodynamics for the gas core reactor concept have all given positive indications of its feasibility. However, before serious design for a full scale gas core application can be made, feasibility must be shown for operation with full interaction of the nuclear, thermal, and hydraulic effects. A minimum sized, and hence minimum expense, test arrangement is considered for a full gas core configuration. It is shown that the hydrogen coolant scattering effects dominate the nuclear considerations at elevated temperatures. A cavity diameter of somewhat larger than 4 ft (122 cm) will be needed if temperatures high enough to vaporize uranium are to be achieved.

  19. Pharmacogenetics of drug-induced arrhythmias : a feasibility study using spontaneous adverse drug reactions reporting data

    NARCIS (Netherlands)

    De Bruin, Marie L; van Puijenbroek, Eugene P; Bracke, Madelon; Hoes, Arno W; Leufkens, Hubert G M

    PURPOSE: The bottleneck in pharmacogenetic research on rare adverse drug reactions (ADR) is retrieval of patients. Spontaneous reports of ADRs may form a useful source of patients. We investigated the feasibility of a pharmacogenetic study, in which cases were selected from the database of a

  20. Ear-EEG from generic earpieces: A feasibility study

    DEFF Research Database (Denmark)

    Kidmose, Preben; Looney, D; Jochumsen, Lars

    2013-01-01

    key patient needs (discreet, unobstrusive, user-friendly, robust) and that is low-cost and suitable for off-the-shelf use; thus promising great advantages for healthcare applications. Its feasibility is validated in a comprehensive comparative study with our established prototype, based...

  1. Pyrolysis in Groningen, Netherlands. Feasibility study on a transition coalition

    International Nuclear Information System (INIS)

    Siemons, R.V.

    2005-01-01

    Results of a study on the technical, economical and financial feasibility of a pyrolysis factory for the processing and energetic application of biomass wastes in the Dutch province Groningen are presented and discussed. Also, attention is paid to the implementation of the planned pyrolysis factory in one or more transition programmes. [nl

  2. A Feasibility Study of Youth Apprenticeship in Arkansas.

    Science.gov (United States)

    Jobs for the Future, Inc., West Somerville, MA.

    A study assessed the feasibility and attractiveness of youth apprenticeship in Arkansas in over 80 interviews with employers in 5 key Arkansas industries and occupations. They were allied health, food processing (equipment repair and maintenance and lab technician/quality control), information services, metalworking, and self-employment and…

  3. Small modular biopower initiative Phase 1 feasibility studies executive summaries

    Energy Technology Data Exchange (ETDEWEB)

    Bain, R.

    2000-03-06

    The Phase 1 objective is a feasibility study that includes a market assessment, resource assessment, preliminary system design, and assessment of relevant environmental and safety considerations, and evaluation of financial and cost issues, and a preliminary business plan and commercialization strategy. Each participating company will share at least 20% of the cost of the first phase.

  4. Staging and storage facility feasibility study. Final report

    International Nuclear Information System (INIS)

    Swenson, C.E.

    1995-02-01

    This study was performed to investigate the feasibility of adapting the design of the HWVP Canister Storage Building (CSB) to meet the needs of the WHC Spent Nuclear Fuel Project for Staging and Storage Facility (SSF), and to develop Rough Order of Magnitude (ROM) cost and schedule estimates

  5. The environmental energy sector programme. Poland: Appendices to feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    The appendices contain Energy Law, Act of 10 April 1997 and also more specific details from the feasibility study for the procurement of a financial solution to the modernisation of the combined heat and power plant in the city of Zielona Gora, Poland. (EHS)

  6. The Pocos de Caldas project feasibility study: 1986-7

    International Nuclear Information System (INIS)

    Smellie, J.A.T.; Chapman, N.A.; Franca, E.P.

    1987-01-01

    This paper presents feasibility studies to investigate the uranium, thorium and rare earth deposits, in Morro do Ferro and the uranium mine in Osamu Utsumi, Brazil, as natural analogues to link rock geochemistry and hydrogeological systems to assess radionuclide mobility. Ore samples were analysed to obtain uranium concentrations and hydraulic tests were carried out. (UK)

  7. Final Technical Report: Renewable Energy Feasibility Study and Resources Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Rivero, Mariah [BEC Environmental, Inc., Las Vegas, NV (United States)

    2016-02-28

    In March 2011, the U.S. Department of Energy (DOE) awarded White Pine County, Nevada, a grant to assess the feasibility of renewable resource-related economic development activities in the area. The grant project included a public outreach and training component and was to include a demonstration project; however, the demonstration project was not completed due to lack of identification of an entity willing to locate a project in White Pine County. White Pine County completed the assessment of renewable resources and a feasibility study on the potential for a renewable energy-focused economic sector within the County. The feasibility study concluded "all resources studied were present and in sufficient quantity and quality to warrant consideration for development" and there were varying degrees of potential economic impact based on the resource type and project size. The feasibility study and its components were to be used as tools to attract potential developers and other business ventures to the local market. White Pine County also marketed the County’s resources to the renewable energy business community in an effort to develop contracts for demonstration projects. The County also worked to develop partnerships with local educational institutions, including the White Pine County School District, conducted outreach and training for the local community.

  8. Feasibility Study for Bioethanol Co-Location with a Coal Fired Power Plant: 29 November 2001--28 July 2002

    Energy Technology Data Exchange (ETDEWEB)

    2002-12-01

    This study looks at the feasibility of co-locating 30, 50, and 70 million gallon per year bioethanol facilities with coal fired power plants in Indiana and Nebraska. Corn stover is the feedstock for ethanol production in both cases.

  9. Training Endogenous Task Shifting Using Music Therapy: A Feasibility Study.

    Science.gov (United States)

    Lynch, Colleen; LaGasse, A Blythe

    2016-01-01

    People with acquired brain injury (ABI) are highly susceptible to disturbances in executive functioning (EF), and these effects are pervasive. Research studies using music therapy for cognitive improvement in this population are limited. The purpose of this study was to determine the feasibility of a Musical Executive Function Training (MEFT) intervention to address task-shifting skills in adults with ABI and to obtain preliminary evidence of intervention effect on task shifting. Fourteen participants were randomly assigned to one of three groups: a music therapy intervention group (MTG), a singing group (SG), or the no-intervention control group (CG). The SG and MTG met for one hour a day for five days. Feasibility measures included participant completion rates and intervention fidelity. Potential benefits were measured using the Trail Making Test and the Paced Auditory Serial Addition Task as a pre- and posttest measure. Participant completion rates and interventionist fidelity to the protocol supported feasibility. One-way ANOVA of the pre- and posttest group differences revealed a trend toward improvement in the MTG over the SG. Feasibility and effect size data support a larger trial of the MEFT protocol. © the American Music Therapy Association 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  10. Construction monitoring constraints and challenges:A feasibility study

    OpenAIRE

    Fidler, Paul; Vardanega, Paul J; Long, Peter; Webb, Graham; Stehle, John; Middleton, Campbell

    2013-01-01

    This paper presents a study of the constraints and challenges faced by the authors when invited to study the feasibility of developing a monitoring system to provide specific information sought by the designer and contractor during the construction of the new 225m high, 48 storey steel-framed Leadenhall Building, located at 122 Leadenhall Street in London. The original goal of the study was to develop a system to assist with the active alignment of the building during construction, a key aim ...

  11. Case study - Argentina

    International Nuclear Information System (INIS)

    Diaz, E.

    1986-01-01

    Antecedents and experience of nuclear activities in Argentina; the Atomic Energy Commission (CNEA). First development and research activities. Research reactors and radioisotopes plants. Health physics and safety regulations. - Feasibility studies for the first nuclear power plant. Awarding the first plant CNA I (Atucha I). Relevant data related to the different project stages. Plant performance. - Feasibility study for the second nuclear power plant. Awarding the second plant CNE (Central Nuclear Embalse). Relevant data related to established targets. Differences compared with the first station targets. Local participation. Plant performance. (orig./GL)

  12. The feasibility of ambitious climate agreements. Norway as an early test case

    Energy Technology Data Exchange (ETDEWEB)

    Andresen, Steinar; Kolshus, Hans H.; Torvanger, Asbjoern

    2002-09-01

    There are considerable differences between developed countries as to how difficult it will be to meet their commitments under the Kyoto Protocol. 'High-cost abatement countries' are particularly interesting as they can be seen as 'test-cases' for other nations in more ambitious climate policy agreements. We assume that a country's objective is to develop an efficient climate policy, achieving cost effectiveness and environmental effectiveness, and that also is politically feasible. Norway is among the countries that will have a hard time in meeting their obligations. Our study suggests that Norway's climate policy has emphasized an international approach, whereas the domestic performance on cost effectiveness has been more moderate. An obvious reason for this is the lower cost associated with the international approach. A 'political cost' associated with such a policy can be criticism from environmental NGOs and other countries. At least in the near term there is little reason to expect 'climate enthusiasm' from the public or many countries of the world. Therefore, just like Norway, they will want emissions reductions carried out as cheaply as possible, which could imply extensive international quota trading, whereas compromises with regard to cost effectiveness are struck at the domestic scene for political feasibility reasons. (author)

  13. Technical design aspects of Feasibility Study-II

    International Nuclear Information System (INIS)

    Zisman, Michael S.

    2001-01-01

    Feasibility Study-II examined a high-performance Neutrino Factory providing 1 x 10 20 neutrinos per year aimed at a long-baseline detector. The Study was sponsored jointly by BNL and the Neutrino Factory and Muon Collider Collaboration ration (MC) and is based on a 1 MW proton driver operating at 24 GeV, i.e., an upgraded version of the AGS accelerator. Compared with the earlier FNAL-sponsored study (Feasibility Study-I), there is a sixfold improvement in performance. Here we describe details of the implementation of Study-II concepts and discuss their efficacy. Alternative approaches that will be pursued in follow-on R and D activities are also described briefly

  14. Feasibility study on production of Co-60 in PHWR

    Energy Technology Data Exchange (ETDEWEB)

    Park, Kyung Bae; Han, Hyon Soo; Joo, Po Kook

    2000-05-01

    The purpose of this study is to analyze the safeties and the economics for Co-60 production from Wolsung PHWR and to verify the feasibility on the manufacturing of the final Co-60 source for industrial irradiation. The feasibility of reactor conversion was carried out with KEPCO collaboration. Through the site survey on the experience of Gentililly-2 in Canada, a feasibility of plant conversion, changes in design, equipment and tools for Co-60 production was verified. It was estimated that the reactor conversion would not impose adverse impact on plant safety. For the encapsulation of radiation source and storage of the final products, a modification of concrete hot cell at KAERI was primary concerns. The installation and improvement of facilities are needed to avoid cross contamination and extra radiation exposure. Main items for these are pressure gauge, separated HEPA filter the ceiling separation, extra-shielding and ceiling hoist system. At present, storage pool has got admission based on 400 kCi. But it is necessary to seismic analysis and design improvement of shielding to store 10 MCi (Co-60) which is the estimated Co-60 capacity produced by 3 PHWRs. According to present investigation, a production of Co-60 by PHWR and RIPE was seemed to be an economically feasible business and it was also expected that a joint venture will be able to realize by cooperation with MDS Nordion Co.

  15. Feasibility study on production of Co-60 in PHWR

    International Nuclear Information System (INIS)

    Park, Kyung Bae; Han, Hyon Soo; Joo, Po Kook

    2000-05-01

    The purpose of this study is to analyze the safeties and the economics for Co-60 production from Wolsung PHWR and to verify the feasibility on the manufacturing of the final Co-60 source for industrial irradiation. The feasibility of reactor conversion was carried out with KEPCO collaboration. Through the site survey on the experience of Gentililly-2 in Canada, a feasibility of plant conversion, changes in design, equipment and tools for Co-60 production was verified. It was estimated that the reactor conversion would not impose adverse impact on plant safety. For the encapsulation of radiation source and storage of the final products, a modification of concrete hot cell at KAERI was primary concerns. The installation and improvement of facilities are needed to avoid cross contamination and extra radiation exposure. Main items for these are pressure gauge, separated HEPA filter the ceiling separation, extra-shielding and ceiling hoist system. At present, storage pool has got admission based on 400 kCi. But it is necessary to seismic analysis and design improvement of shielding to store 10 MCi (Co-60) which is the estimated Co-60 capacity produced by 3 PHWRs. According to present investigation, a production of Co-60 by PHWR and RIPE was seemed to be an economically feasible business and it was also expected that a joint venture will be able to realize by cooperation with MDS Nordion Co

  16. Feasibility study of fusion breeding blanket concept employing graphite reflector

    International Nuclear Information System (INIS)

    Cho, Seungyon; Ahn, Mu-Young; Lee, Cheol Woo; Kim, Eung Seon; Park, Yi-Hyun; Lee, Youngmin; Lee, Dong Won

    2015-01-01

    Highlights: • A Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept adopts graphite as a reflector material by reducing the amount of beryllium multiplier. • Its feasibility was investigated in view point of the nuclear performance as well as material-related issues. • A nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket. • Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions. • In conclusion, the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition. - Abstract: To obtain high tritium breeding performance with limited blanket thickness, most of solid breeder blanket concepts employ a combination of lithium ceramic as a breeder and beryllium as a multiplier. In this case, considering that huge amount of beryllium are needed in fusion power plants, its handling difficulty and cost can be a major factor to be accounted for commercial use. Korea has proposed a Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept relevant to fusion power plants. Here, graphite is used as a reflector material by reducing the amount of beryllium multiplier. Its feasibility has been investigated in view point of the nuclear performance as well as material-related issues. In this paper, a nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket, considering tritium breeding capability and neutron shielding and activation aspects. Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions, resulting in that the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition.

  17. Feasibility study of fusion breeding blanket concept employing graphite reflector

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Seungyon, E-mail: sycho@nfri.re.kr [National Fusion Research Institute, Daejeon (Korea, Republic of); Ahn, Mu-Young [National Fusion Research Institute, Daejeon (Korea, Republic of); Lee, Cheol Woo; Kim, Eung Seon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Yi-Hyun; Lee, Youngmin [National Fusion Research Institute, Daejeon (Korea, Republic of); Lee, Dong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    Highlights: • A Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept adopts graphite as a reflector material by reducing the amount of beryllium multiplier. • Its feasibility was investigated in view point of the nuclear performance as well as material-related issues. • A nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket. • Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions. • In conclusion, the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition. - Abstract: To obtain high tritium breeding performance with limited blanket thickness, most of solid breeder blanket concepts employ a combination of lithium ceramic as a breeder and beryllium as a multiplier. In this case, considering that huge amount of beryllium are needed in fusion power plants, its handling difficulty and cost can be a major factor to be accounted for commercial use. Korea has proposed a Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept relevant to fusion power plants. Here, graphite is used as a reflector material by reducing the amount of beryllium multiplier. Its feasibility has been investigated in view point of the nuclear performance as well as material-related issues. In this paper, a nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket, considering tritium breeding capability and neutron shielding and activation aspects. Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions, resulting in that the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition.

  18. Project management case studies

    CERN Document Server

    Kerzner, Harold R

    2013-01-01

    A new edition of the most popular book of project management case studies, expanded to include more than 100 cases plus a ""super case"" on the Iridium Project Case studies are an important part of project management education and training. This Fourth Edition of Harold Kerzner''s Project Management Case Studies features a number of new cases covering value measurement in project management. Also included is the well-received ""super case,"" which covers all aspects of project management and may be used as a capstone for a course. This new edition:Contains 100-plus case studies drawn from re

  19. CVD diamond Brewster window: feasibility study by FEM analyses

    Directory of Open Access Journals (Sweden)

    Vaccaro A.

    2012-09-01

    Full Text Available Chemical vapor deposition (CVD diamond windows are a crucial component in heating and current drive (H&CD applications. In order to minimize the amount of reflected power from the diamond disc, its thickness must match the desired beam wavelength, thus proper targeting of the plasma requires movable beam reflectors. This is the case, for instance, of the ITER electron cyclotron H&CD system. However, looking at DEMO, the higher heat loads and neutron fluxes could make the use of movable parts close to the plasma difficult. The issue might be solved by using gyrotrons able to tune the beam frequency to the desired resonance, but this concept requires transmission windows that work in a given frequency range, such as the Brewster window. It consists of a CVD diamond disc brazed to two copper cuffs at the Brewster angle. The brazing process is carried out at about 800°C and then the temperature is decreased down to room temperature. Diamond and copper have very different thermal expansion coefficients, therefore high stresses build up during the cool down phase that might lead to failure of the disc. Considering also the complex geometry of the window with the skewed position of the disc, analyses are required in the first place to check its feasibility. The cool down phase was simulated by FEM structural analyses for several geometric and constraint configurations of the window. A study of indirect cooling of the window by water was also performed considering a HE11 mode beam. The results are here reported.

  20. Case Study Research Methodology

    Directory of Open Access Journals (Sweden)

    Mark Widdowson

    2011-01-01

    Full Text Available Commenting on the lack of case studies published in modern psychotherapy publications, the author reviews the strengths of case study methodology and responds to common criticisms, before providing a summary of types of case studies including clinical, experimental and naturalistic. Suggestions are included for developing systematic case studies and brief descriptions are given of a range of research resources relating to outcome and process measures. Examples of a pragmatic case study design and a hermeneutic single-case efficacy design are given and the paper concludes with some ethical considerations and an exhortation to the TA community to engage more widely in case study research.

  1. Feasibility study of component risk ranking for plant maintenance

    International Nuclear Information System (INIS)

    Ushijima, Koji; Yonebayashi, Kenji; Narumiya, Yoshiyuki; Sakata, Kaoru; Kumano, Tetsuji

    1999-01-01

    Nuclear power is the base load electricity source in Japan, and reduction of operation and maintenance cost maintaining or improving plant safety is one of the major issues. Recently, Risk Informed Management (RIM) is focused as a solution. In this paper, the outline regarding feasibility study of component risk ranking for plant maintenance for a typical Japanese PWR plant is described. A feasibility study of component risk raking for plant maintenance optimization is performed on check valves and motor-operated valves. Risk ranking is performed in two steps using probabilistic analysis (quantitative method) for risk ranking of components, and deterministic examination (qualitative method) for component review. In this study, plant components are ranked from the viewpoint of plant safety / reliability, and the applicability for maintenance is assessed. As a result, distribution of maintenance resources using risk ranking is considered effective. (author)

  2. Feasibility study on the thorium fueled boiling water breeder reactor

    International Nuclear Information System (INIS)

    PetrusTakaki, N.

    2012-01-01

    The feasibility of (Th,U)O 2 fueled, boiling water breeder reactor based on conventional BWR technology has been studied. In order to determine the potential use of water cooled thorium reactor as a competitive breeder, this study evaluated criticality, breeding and void reactivity coefficient in response to changes made in MFR and fissile enrichments. The result of the study shows that while using light water as moderator, low moderator to fuel volume ratio (MFR=0.5), it was possible to breed fissile fuel in negative void reactivity condition. However the burnup value was lower than the value of the current LWR. On the other hand, heavy water cooled reactor shows relatively wider feasible breeding region, which lead into possibility of designing a core having better neutronic and economic performance than light water with negative void reactivity coefficient. (authors)

  3. Fast-mixed spectrum reactor interim report initial feasibility study

    International Nuclear Information System (INIS)

    Fischer, G.J.; Cerbone, R.J.

    1979-01-01

    The report summarizes the results of an initial four-month feasibility study of the Fast-Mixed Spectrum Reactor (FMSR). Reactor physics, fuel cycle, and thermal-hydraulic analyses were performed on a reference design. These results when coupled to a fuel and materials evaluation performed in cooperation with the Argonne National Laboratory indicate that the FMSR is feasible provided the fuels, cladding, and subassembly ducts can survive a peak fuel burnup of 15 to 20 atom percent heavy metal and peak fluences of 8 x 10 23 (nvt > 0.1 MeV). The results of this short study have also provided a basis for exploring alternative designs requiring significantly lower peak burnup and fluences for their operation

  4. Cogeneration feasibility study in the Gulf States Utilities service area

    Energy Technology Data Exchange (ETDEWEB)

    1979-12-01

    Sites in the Gulf States Utilities service are considered for cogeneration feasibility studies. The sources of steam considered for the Orange, Texas and Geismar, Lake Charles, and North Baton Rouge, Louisiana sites include oil, coal, HTGR steamers, consolidated nuclear steam system, atmospheric fluidized-bed coal combustion, and coal gasification. Concepts concerning cogeneration fuel systems were categorized by technical applicability as: current technology (pulverized coal-fired boilers and fuel oil-fired boilers), advanced technology under development (HTGR steamers and the CNSS), and advanced technology for future development (atmospheric fluidized-bed boilers and coal gasification). In addition to providing data on cogeneration plant generally useful in the US, the study determined the technical and economic feasibility of steam and electric power cogeneration using coal and nuclear fuels for localized industrial complexes. Details on site selection, plant descriptions, cost estimates, economic analysis, and plant schedule and implementation. (MCW)

  5. Pre-feasibility study of 80mw onshore wind farm

    International Nuclear Information System (INIS)

    Almas, M.S.

    2014-01-01

    This paper discusses a pre-feasibility study of 80MW onshore wind farm in the KPK (Khyber Pakhtunkhwa) province previously known as NWFP (North West Frontier) Province of Pakistan. The realistic data of wind speed is collected from Laboratory of Meteorology and Climatology (University of the Punjab) to study the feasibility of wind farm. Detailed analysis of wind turbines from four different manufacturers is carried out together with justifications of selecting a particular wind turbine. Issues related to site selection, wind farm civil foundation, recommendations for a particular choice of tower along with environmental effects are presented. Wind data analysis is carried out by using WINDROSE PRO software to determine the resultant direction of wind at the selected site for wind farm layout. The wind distribution at hub height of the wind turbine is calculated and is used to compute annual power production by the wind farm using power curves of the wind turbine. Electrical network integration issues of wind farm to the external grid are studied and the optimum point of connection is proposed. Finally, economic analysis of the whole wind farm project depending upon the LCC (Life Cycle Cost Analysis) is presented and the feasibility of the project from the investor's point of view is identified. The study concludes that the cost per kilowatt hour of electricity generated by this wind power plant will be 10.4 PKR/kWh and the payback period for the whole project is about 11.2 years. (author)

  6. Pre-Feasibility Study of 80MW Onshore Wind Farm

    Directory of Open Access Journals (Sweden)

    Muhammad Shoaib Almas

    2014-10-01

    Full Text Available This paper discusses a pre-feasibility study of 80MW onshore wind farm in the KPK (Khyber Pakhtunkhwa province previously known as NWFP (North West Frontier Province of Pakistan. The realistic data of wind speed is collected from Laboratory of Meteorology & Climatology (University of the Punjab to study the feasibility of wind farm. Detailed analysis of wind turbines from four different manufacturers is carried out together with justifications of selecting a particular wind turbine. Issues related to site selection, wind farm civil foundation, recommendations for a particular choice of tower along with environmental effects are presented. Wind data analysis is carried out by using WINDROSE PRO software to determine the resultant direction of wind at the selected site for wind farm layout. The wind distribution at hub height of the wind turbine is calculated and is used to compute annual power production by the wind farm using power curves of the wind turbine. Electrical network integration issues of wind farm to the external grid are studied and the optimum point of connection is proposed. Finally, economic analysis of the whole wind farm project depending upon the LCC (Life Cycle Cost Analysis is presented and the feasibility of the project from the investor?s point of view is identified. The study concludes that the cost per kilowatt hour of electricity generated by this wind power plant will be 10.4 PKR/kWh and the payback period for the whole project is about 11.2 years

  7. Technical Feasibility Study for Zero Energy K-12 Schools

    Energy Technology Data Exchange (ETDEWEB)

    Bonnema, Eric [National Renewable Energy Lab. (NREL), Golden, CO (United States); Goldwasser, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Torcellini, Paul [National Renewable Energy Lab. (NREL), Golden, CO (United States); Pless, Shanti [National Renewable Energy Lab. (NREL), Golden, CO (United States); Studer, Daniel [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-11-01

    This technical feasibility study provides documentation and research results supporting a possible set of strategies to achieve source zero energy K-12 school buildings as defined by the U.S. Department of Energy (DOE) zero energy building (ZEB) definition (DOE 2015a). Under this definition, a ZEB is an energy-efficient building in which, on a source energy basis, the actual annual delivered energy is less than or equal to the on-site renewable exported energy.

  8. Coeur d'Alene Tribe Energy Efficiency Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Allgood, Tiffany L. [Coeur d' Alene Tribe, Plummer, ID (United States); Sorter, Andy [Coeur d' Alene Tribe, Plummer, ID (United States)

    2014-09-01

    The Coeur d'Alene Tribe's Energy Efficiency Feasibility Study (EEFS) is the culminating document that compiles the energy efficiency and building performance assessment and project prioritization process completed on 36 Tribally owned and operated facilities within Tribal lands. The EEFS contains sections on initial findings, utility billing analyses, energy conservation measures and prioritization and funding sources and strategies for energy project implementation.

  9. Dual-gated cardiac PET-clinical feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Teraes, Mika; Kokki, Tommi; Noponen, Tommi; Hoppela, Erika; Sipilae, Hannu T.; Knuuti, Juhani [Turku PET Centre, PO BOX 52, Turku (Finland); Durand-Schaefer, Nicolas [General Electric Medical Systems, Buc (France); Pietilae, Mikko [Turku University Hospital, Department of Internal Medicine, Turku (Finland); Kiss, Jan [Turku University Hospital, Department of Surgery, Turku (Finland)

    2010-03-15

    Both respiratory and cardiac motions reduce image quality in myocardial imaging. For accurate imaging of small structures such as vulnerable coronary plaques, simultaneous cardiac and respiratory gating is warranted. This study tests the feasibility of a recently developed robust method for cardiac-respiratory gating. List-mode data with triggers from respiratory and cardiac cycles are rearranged into dual-gated segments and reconstructed with standard algorithms of a commercial PET/CT scanner. Cardiac gates were defined as three fixed phases and one variable diastolic phase. Chest motion was measured with a respiratory gating device and post-processed to determine gates. Preservation of quantification in dual-gated images was tested with an IEC whole-body phantom. Minipig and human studies were performed to evaluate the feasibility of the method. In minipig studies, a coronary catheter with radioactive tip was guided in coronary artery for in vivo and ex vivo acquisitions. Dual gating in humans with suspected cardiac disorders was performed using 18-F-FDG as a tracer. The method was found feasible for in vivo imaging and the radioactive catheter tip was better resolved in gated images. In human studies, the dual gating was found feasible and easy for clinical routine. Maximal movement of myocardial surface in cranio-caudal direction was over 20 mm. The shape of myocardium was clearly different between the gates and papillary muscles become more visible in diastolic images. The first clinical experiences using robust cardiac-respiratory dual gating are encouraging. Further testing in larger clinical populations using tracers designed especially for plaque imaging is warranted. (orig.)

  10. Dual-gated cardiac PET-clinical feasibility study

    International Nuclear Information System (INIS)

    Teraes, Mika; Kokki, Tommi; Noponen, Tommi; Hoppela, Erika; Sipilae, Hannu T.; Knuuti, Juhani; Durand-Schaefer, Nicolas; Pietilae, Mikko; Kiss, Jan

    2010-01-01

    Both respiratory and cardiac motions reduce image quality in myocardial imaging. For accurate imaging of small structures such as vulnerable coronary plaques, simultaneous cardiac and respiratory gating is warranted. This study tests the feasibility of a recently developed robust method for cardiac-respiratory gating. List-mode data with triggers from respiratory and cardiac cycles are rearranged into dual-gated segments and reconstructed with standard algorithms of a commercial PET/CT scanner. Cardiac gates were defined as three fixed phases and one variable diastolic phase. Chest motion was measured with a respiratory gating device and post-processed to determine gates. Preservation of quantification in dual-gated images was tested with an IEC whole-body phantom. Minipig and human studies were performed to evaluate the feasibility of the method. In minipig studies, a coronary catheter with radioactive tip was guided in coronary artery for in vivo and ex vivo acquisitions. Dual gating in humans with suspected cardiac disorders was performed using 18-F-FDG as a tracer. The method was found feasible for in vivo imaging and the radioactive catheter tip was better resolved in gated images. In human studies, the dual gating was found feasible and easy for clinical routine. Maximal movement of myocardial surface in cranio-caudal direction was over 20 mm. The shape of myocardium was clearly different between the gates and papillary muscles become more visible in diastolic images. The first clinical experiences using robust cardiac-respiratory dual gating are encouraging. Further testing in larger clinical populations using tracers designed especially for plaque imaging is warranted. (orig.)

  11. Preliminary study on the feasibility of ductless fuel assembly for fast reactors

    International Nuclear Information System (INIS)

    Shibahara, Itaru; Enokido, Yuji

    1988-01-01

    Preliminary study on the feasibility of ductless fuel assembly for fast reactors has been conducted. The primary concern is with forecasting the thermal hydraulic characteristics and the heat removal efficiency from the core. The thermal hydraulic analysis revealed the coolant mixing in the core at steady state operating condition was not intensive and the coolant temperature increase was almost proportional to the power of each assembly. The hot spot analysis of the ductless core indicated that the hottest temperature in the core could be comparable with the temperature of the conventional ducted core, even in case the radial power flattening was not actively pursued but with adopting ducted radial blanket assemblies. Under off-normal conditions, the ductless core had improved heat removal capability which was caused by inter-assembly coolant flow. The study has indicated the feasibility of the ductless fuel assembly for fast reactors. The experiments to demonstrate the feasibility will be the next key process for the development. (author)

  12. Feasibility Study for a Hopi Utility-Scale Wind Project

    Energy Technology Data Exchange (ETDEWEB)

    Kendrick Lomayestewa

    2011-05-31

    The goal of this project was to investigate the feasibility for the generation of energy from wind and to parallel this work with the development of a tribal utility organization capable of undertaking potential joint ventures in utility businesses and projects on the Hopi reservation. The goal of this project was to investigate the feasibility for the generation of energy from wind and to parallel this work with the development of a tribal utility organization capable of undertaking potential joint ventures in utility businesses and projects on the Hopi reservation. Wind resource assessments were conducted at two study sites on Hopi fee simple lands located south of the city of Winslow. Reports from the study were recently completed and have not been compared to any existing historical wind data nor have they been processed under any wind assessment models to determine the output performance and the project economics of turbines at the wind study sites. Ongoing analysis of the wind data and project modeling will determine the feasibility of a tribal utility-scale wind energy generation.

  13. [Feasibility study for whole plant medicinal use of Tribulus terrestris].

    Science.gov (United States)

    Yang, Li; Wang, Chunyu; Han, Meiw; Yang, Limin

    2009-09-01

    The content differences of leaf, plant and fruit of Tribulus terrestris was compared to study the feasibility of whole plant medicinal use. The samples were collected in three typical habitats and six different production areas of T. terrestris. The main medicinal ingredients saponins and flavonoids were determined in root, stem, leaf and fruit during the harvest time. The two ingredients were abounded in leaf and more than 2.61 times as in other parts of the plant. The results showed that there were no differences between the whole plant and the fruit. It should pay more attentions on the collection, preservation and utilization of the leaf of T. terrestris in the harvesting and processing stage. The whole plant for medical use was feasibility based on the content of the ingredients.

  14. Code of Conduct for wind-power projects - Feasibility study

    International Nuclear Information System (INIS)

    Strub, P.; Ziegler, Ch.

    2009-02-01

    This final report deals with the results of a feasibility study concerning the development of a Code of Conduct for wind-power projects. The aim is to strengthen the acceptance of wind-power by the general public. The necessity of new, voluntary market instruments is discussed. The urgency of development in this area is quoted as being high, and the authors consider the feasibility of the definition of a code of conduct as being proven. The code of conduct can, according to the authors, be of use at various levels but primarily in project development. Further free-enterprise instruments are also suggested that should help support socially compatible and successful market development. It is noted that the predominant portion of those questioned are prepared to co-operate in further work on the subject

  15. Feasibility Study on Manufacturing Lightweight Aggregates from Water Purification Sludge

    Science.gov (United States)

    Peng, Ching-Fang; Chen, How-Ji

    2018-02-01

    This study mainly discussed the feasibility of manufacturing lightweight aggregates from water purification sludge in Taiwan. They were analysed for the physical and chemical composition before the sintering test for lightweight aggregates in a laboratory. Then the physical and mechanical properties of the synthesized aggregates were assessed. The result showed that the chemical composition of sludge in the water purification plants was within the appropriate range for manufacturing lightweight aggregate as proposed in the literature. The sintering test demonstrated that the particle density of aggregates from the ten types of water purification sludge were mostly less than 1.8 g/cm3. In addition, the dry unit weight, the organic impurity, the ignition loss, and other characteristics of synthesized aggregates met the requirement of CNS standards, while its water absorption and crushing strength also fulfilled the general commercial specifications. Therefore, reclamation of water purification sludge for production of lightweight aggregate is indeed feasible.

  16. PUEBLO OF ZIA RENEWABLE ENERGY DEVELOPMENT FEASIBILITY STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Pino, Peter M. [Tribal Administrator (Ret.), Pueblo of Zia; Lakshman, Jai [Project Manager (NDA) for Pueblo of Zia; Toole, G. Loren [Principal Investigator, Los Alamos National Laboratory - Energy Analysis Team/ CCS-3, D-4; Hand, Dan [P.E., Sustainable Enginerring; Witcher, James; Emerson, Michael A. [Senior V.P., ARES Corporation; Turner, Jeremy [Executive Director, NM Renewable Energy Transmission Authority; Sandidge, Wendy [Director of Operations, NM Community Capital

    2014-06-30

    The Pueblo of Zia will conduct a comprehensive feasibility study for best-use application(s) for development of renewable energy resources on its tribally held TRUST lands (i.e., Trust Lands of Zia Indian Reservation). The feasibility study is essential for determining the technical and economic viability of a future renewable project(s) on Zia tribal lands, including the potential economic and environmental benefits for the Tribe. Project Objectives: The feasibility study is essential for determining the technical and economic viability of future renewable project(s) on Zia tribal lands, including the potential economic and environmental benefits for the Tribe to: 1. Provide a balanced local renewable power supply for Zia Pueblo, its members, tribal offices, schools and buildings, and businesses on tribal lands 2. Provide a firm power supply for export and commercial market distribution 3. Provide economic development for the Tribe and its members, including job training and creation, each in accordance with the goals and objectives as conveyed by the Pueblo of Zia Tribal Council, Tribal Administration, and outlined in The Pueblo of Zia Comprehensive Plan and Pueblo of Zia — Zia Enterprise Zone Master Plan. A key goal of the study is to analyze the integrated development of solar, geothermal, and wind renewable energy resources at Zia Pueblo, with added potential to combine gas-fired generation to accomplish energy firming. Geothermal offers a base load source of energy, providing power continuously for end users. Wind and solar offer intermediate and peaking sources of energy, which can be harvested throughout the day, with periods of variable but predicable output. Variability will be managed in an integrated manner, using Zia Pueblo's combined renewable resources to generate high-quality power. Tasks are intended to collect, catalog, map, and analyze existing data on Zia Pueblo's renewable energy resource base and then match resource attributes with

  17. Feasibility study on large pool-type LMFBR

    International Nuclear Information System (INIS)

    1984-01-01

    A feasibility study has been conducted from 1981 FY to 1983 FY, in order to evaluate the feasibility of a large pool-type LMFBR under the Japanese seismic design condition and safety design condition, etc. This study was aimed to establish an original reactor structure concept which meets those design conditions especially required in Japan. In the first year, preceding design concepts had been reviewed and several concepts were originated to be suitable to Japan. For typical two of them being selected by preliminary analysis, test programs were planned. In the second year, more than twenty tests with basic models had been conducted under severe conditions, concurrently analytical approaches were promoted. In the last year, larger model tests were conducted and analytical methods have been verified concerning hydrodynamic effects on structure vibration, thermo-hydraulic behaviours in reactor plena and so on. Finally the reactor structure concepts for a large pool-type LMFBR have been acknowledged to be feasible in Japan. (author)

  18. TMI-2 fuel-recovery plant. Feasibility study

    International Nuclear Information System (INIS)

    Evans, D.L.

    1982-12-01

    This project is a feasibility study for constructing a TMI-2 core Fuel Recovery Plant at the Idaho National Engineering Laboratory (INEL). The primary objectives of the Fuel Recovery Plant (FRP) are to recover and account for the fuel and to process, isolate, and package the waste material from the TMI-2 core. This feasibility study is predicated on a baseline plant and covers its design, fabrication, installation, testing and operation. Alternative methods for the disposal of the TMI-2 core have also been considered, but not examined in detail for their feasibility. The FRP will receive TMI-2 fuel in canisters. The fuel will vary from core debris to intact fuel assemblies and include some core structural materials. The canister contents will be shredded and subsequently fed to a dissolver. Uranium, plutonium, fission products, and some core structural material will be dissolved. The uranium will be separated by solvent extraction and solidified by calcination. The plutonium will also be separated by solvent extraction and routed to the Plutonium Extraction Facility. The wastes will be packaged for further treatment, temporary storage or permanent disposal

  19. The feasibility study on commercialized fast reactor cycle system

    International Nuclear Information System (INIS)

    Noda, Hiroshi

    2002-01-01

    The feasibility study on commercialized Fast Reactor cycle system (FS) has been carried out by a joint team with the participation of all parties concerned in Japan since July, 1999. It aims to clarify various perspectives for commercialized fast reactor cycle system and also suggest development strategies to diverse social needs in the 21 st century. The FS consists of several phases. The phase 1 has progressed as planned and the highly feasible candidate concepts with innovative technologies have been screened out among a wide variety of concepts. During the phase 2, approximately five years after the phase 1, the in-depth design studies and engineering scale tests of key technologies are being conducted to verify and validate the feasibility of screened candidate concepts. At the end of the phase 2, a few promising concepts will be selected with their R and D tasks. The paper describes the results of the phase 1, the activities of the phase 2 and the new concept related to the fast reactor fuel cycle focusing on the reduction in environmental burden, which is one of key factors to sustain the nuclear power generation in the 21 st century

  20. Pascua Yaqui Tribe Renewable Energy Development and Deployment Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Arvayo, Maria

    2014-05-30

    In 2012, PYT was awarded a grant from the Department of Energy Tribal Energy Program to conduct a Renewable Energy Development and Deployment Feasibility Study that would define the technical and economic viability of renewable energy on tribal lands. Red Mountain Energy Partners (RMEP) was hired by PYT to complete the study. Through this study, Red Mountain concluded that there are viable opportunities for solar at Tortuga Ranch, the Casino del Sol and a third site near the Justice Center on Camino de Oeste.

  1. Feasibility study of a contained pulsed nuclear propulsion engine

    International Nuclear Information System (INIS)

    Parlos, A.G.; Metzger, J.D.

    1994-01-01

    The result of a feasibility analysis of a contained pulsed nuclear propulsion (CPNP) engine concept utilizing the enormously dense energy generated by small nuclear detonations is presented in this article. This concept was initially proposed and studied in the 1950s and 1960s under the program name HELIOS. The current feasibility of the concept is based upon materials technology that has advanced to a state that allows the design of pressure vessels required to contain the blast associated with small nuclear detonations. The impulsive nature of the energy source provides the means for circumventing the materials thermal barriers that are inherent in steady-state nuclear propulsion concepts. The rapid energy transfer to the propellant results in high thrust levels for times less than 1 s following the detonation. The preliminary feasibility analysis using off-the-shelf materials technology appears to indicate that the CPNP concept can have thrust-to-weight ratios on the order of 1 or greater. Though the specific impulse is not a good indicator for impulsive engines, an operating-cycle averaged specific impulse of approximately 1000 or greater seconds was calculated. 16 refs

  2. Biogas Koczala. Biogas project in Koczala. Feasibility study. Technical report

    International Nuclear Information System (INIS)

    2004-08-01

    The present production of district heating in Koczala is based on coal. The district heating system is worn out technically and economically and according to the 2001 Energy Plan of Koczala the district heating plant shall be converted to a combination of a biogas fired CHP and a wood chip boiler. The overall objective of this project is to access the feasibility and viability construction an operation of a biogas plant owned by the co-operative agricultural company, Poldanor S.A. The feasibility study includes: 1) Availability of organic waste in the Koczala area, 2) Possibilities of using energy crops in the biogas plant, 3) Possibilities of receiving grants from the Polish National Fund for Environmental Protection, the new EU regional funds and through the joint implementation market (CO 2 quotas), 4) Alternative locations of the biogas plant and the CHP unit, 5) Alternative strategies for selling electricity and heat, 6) Organisational issues (ownership). This report concludes that implementing the biogas project is environmentally and financially feasible and viable. If organic waste and/or maize silage can be provided and gasified without problems, the plant can supply as well the Koczala farm as the fodder mill with steam and heat, and also supply Koczala district heating system with approx. 75% of yearly heat consumption. Furthermore, electricity is supplied to the fodder mill and the public grid. (BA)

  3. Feasibility study on the development of proton accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Ki Hyung; Bang, Hyung Chan; Cho, Yong Sup [Seoul National University, Seoul (Korea, Republic of); Kim, Young Rak [Church Environment Research Institute, Seoul (Korea, Republic of); Nam Kung, Won; Cho, Moo Hyun [Pohang University of Science and Technology, Pohang (Korea, Republic of); Seo, Tae Suk [Cartolrik University, Seoul (Korea, Republic of); Woo, Hyung Joo [Nature Research Institute, Seoul (Korea, Republic of); Lee, Kyung Soo [Basic Study Research Institute, Seoul (Korea, Republic of); Lee, Hun Joo [Cheju National University, Cheju (Korea, Republic of); Chang, Soon Hong; Cho, Nam Jin [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of); Han, Jeon Kun [Sungkyunkwan University, Seoul (Korea, Republic of)

    1996-10-01

    A feasibility on the development of a high energy proton accelerator to be used for R and D in the nuclear field of korea was studied. The proposed one is a proton linac with parameters of about 1 GeV, 20 mA which can supply enough neutrons by the spallation reaction to drive a subcritical reactor. It= is expected to solve the intrinsic problem in the nuclear field such as safety, nuclear waste, proliferation and resource. The study was carried out through a multi-institutional cooperation of universities, institute and industry for a national consensus. 5 refs., 8 tabs., 8 figs. (author)

  4. Feasibility study for mega-electron-volt electron beam tomography.

    Science.gov (United States)

    Hampel, U; Bärtling, Y; Hoppe, D; Kuksanov, N; Fadeev, S; Salimov, R

    2012-09-01

    Electron beam tomography is a promising imaging modality for the study of fast technical processes. But for many technical objects of interest x rays of several hundreds of keV energy are required to achieve sufficient material penetration. In this article we report on a feasibility study for fast electron beam computed tomography with a 1 MeV electron beam. The experimental setup comprises an electrostatic accelerator with beam optics, transmission target, and a single x-ray detector. We employed an inverse fan-beam tomography approach with radiographic projections being generated from the linearly moving x-ray source. Angular projections were obtained by rotating the object.

  5. Laparoscopic cholecystectomy under epidural anesthesia: a clinical feasibility study.

    Science.gov (United States)

    Lee, Ji Hyun; Huh, Jin; Kim, Duk Kyung; Gil, Jea Ryoung; Min, Sung Won; Han, Sun Sook

    2010-12-01

    Laparoscopic cholecystectomy (LC) has traditionally been performed under general anesthesia, however, owing in part to the advancement of surgical and anesthetic techniques, many laparoscopic cholecystectomies have been successfully performed under the spinal anesthetic technique. We hoped to determine the feasibility of segmental epidural anesthesia for LC. Twelve American Society of Anesthesiologists class I or II patients received an epidural block for LC. The level of epidural block and the satisfaction score of patients and the surgeon were checked to evaluate the efficacy of epidural block for LC. LC was performed successfully under epidural block, with the exception of 1 patient who required a conversion to general anesthesia owing to severe referred pain. There were no special postoperative complications, with the exception of one case of urinary retention. Epidural anesthesia might be applicable for LC. However, the incidence of intraoperative referred shoulder pain is high, and so careful patient recruitment and management of shoulder pain should be considered.

  6. Feasibility study for remote assessment of cognitive function in multiple sclerosis.

    Science.gov (United States)

    George, Michaela F; Holingue, Calliope B; Briggs, Farren B S; Shao, Xiaorong; Bellesis, Kalliope H; Whitmer, Rachel A; Schaefer, Catherine; Benedict, Ralph Hb; Barcellos, Lisa F

    2016-01-01

    Cognitive impairment is common in multiple sclerosis (MS), and affects employment and quality of life. Large studies are needed to identify risk factors for cognitive decline. Currently, a MS-validated remote assessment for cognitive function does not exist. Studies to determine feasibility of large remote cognitive function investigations in MS have not been published. To determine whether MS patients would participate in remote cognitive studies. We utilized the Modified Telephone Interview for Cognitive Status (TICS-M), a previously validated phone assessment for cognitive function in healthy elderly populations to detect mild cognitive impairment. We identified factors that influenced participation rates. We investigated the relationship between MS risk factors and TICS-M score in cases, and score differences between cases and control individuals. The TICS-M was administered to MS cases and controls. Linear and logistic regression models were utilized. 11.5% of eligible study participants did not participate in cognitive testing. MS cases, females and individuals with lower educational status were more likely to refuse (pTICS-M score among cases (pTICS-M score was significantly lower in cases compared to controls (p=0.007). Our results demonstrate convincingly that a remotely administered cognitive assessment is quite feasible for conducting large epidemiologic studies in MS, and lay the much needed foundation for future work that will utilize MS-validated cognitive measures.

  7. Feasibility study of gasification of oil palm fronds

    Directory of Open Access Journals (Sweden)

    S.A. Sulaiman

    2015-12-01

    Full Text Available Considering the large and consistent supply, oil palm fronds could be a promising source of biomass energy through gasification. There is very scarce information on the characteristics of oil palm fronds, which is vital in deciding if such biomass is technically suitable for gasification. In the present work, the feasibility of oil palm fronds for biomass gasification is studied. The study is conducted experimentally via standard tests to determine their thermochemical characteristics. Ultimate analysis is conducted to determine the contents of carbon, nitrogen, hydrogen and sulphide in oil palm fronds. Proximate analysis is performed to identify the burning characteristics of the biomass. The energy content in the fronds is determined by using a bomb calorie meter and is around 18 MJ/kg. The ignitability of the fronds is also studied experimentally to assess the ease to start-up combustion of the fronds. The characteristics of the flame of the resulting syngas from gasification of oil palm fronds are qualitatively studied. Simulated syngas composition study reveals potentials of 22% CO, 1.3% H2, 18.5% CO2 and traces of CH4. The study is extended to computer simulation to predict composition of the syngas. It is found from this work that oil palm fronds are feasible for gasification and has a good potential as a renewable energy source.

  8. 100-HR-2 Operable Unit Focused Feasibility study report

    International Nuclear Information System (INIS)

    1995-01-01

    The standard Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) Feasibility Study (FS) includes development and screening of alternatives (Phases 1 and 2) and the detailed analysis of alternatives (Phase 3). This focused feasibility study (FFS) was conducted for the 100-HR-2 Operable Unit (OU) at the Hanford Site in southeastern Washington. This FFS constitutes the Phase 3 portion of the FS process for the remedial alternatives initially developed and screened in the 100 Area Feasibility Study Phases 1 and 2 (DOE-RL 1993a). The objective of this OU-specific FFS is to provide decision makers with sufficient information to allow appropriate and timely selection of interim remedial measures (IRM) for the seven IRM candidate sites associated with the 100-HR-2 OU. The IRM candidate waste sites identified in Table ES-1 are determined in the limited field investigation (DOE-RL 1994b). Site profiles are developed for each of these waste sites. The site profiles are used in the application of the plug-in approach. The waste site either plugs into the analysis of the alternatives for the group, or deviations from the developed group alternatives are described and documented. A summary for the 100-HR-2 IRM candidate waste site is as follows: none of the waste sites require additional alternative development. six of the seven waste sites directly plug into the waste site group alternatives. The site-specific detailed analysis is conducted, referencing the waste site group analysis as appropriate. A waste site detailed analysis summary is presented in Table ES-1.A comparative analysis of remedial alternatives is presented for each waste site. A summary of the comparative analysis is presented in Table ES-2

  9. 451 Case studies Cardiac

    African Journals Online (AJOL)

    Marinda

    Case Studies. 29 ... A case of a 26-year-old ASA I physical status male undergoing septoplasty had an abrupt ... myocardial infarction, severe hypertensive crisis, cerebral .... or no formal management is required in an ASA I patient.8 One.

  10. Feasibility Study for Operable Unit 7-13/14

    International Nuclear Information System (INIS)

    K. Jean Holdren Thomas E. Bechtold Brian D. Preussner

    2007-01-01

    The Subsurface Disposal Area is a radioactive waste landfill located within the Radioactive Waste Management Complex at the Idaho National Laboratory Site in southeastern Idaho. This Feasibility Study for Operable Unit 7-13/14 analyzes options for mitigating risks to human health and the environment associated with the landfill. Analysis is conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act, using nine evaluation criteria to develop detailed and comparative analysis of five assembled alternatives. Assembled alternatives are composed of discrete modules. Ultimately, decision-makers will select, recombine, and sum various modules into an optimized preferred alternative and final remedial decision

  11. A study on the feasibility of minor actinides in BWR

    International Nuclear Information System (INIS)

    Abdul Waris; Budiono

    2008-01-01

    Preliminary study on the feasibility of actinides minor (MA) recycling without mixing them with plutonium in boiling water reactor (BWR) has been carried out. The results show that increasing of fissile MA content in mixed oxide fuel (MOX) and/or reducing void fraction can enlarge the effective multiplication factor at the beginning of cycle, but the reactor still can not obtain its criticality condition. Furthermore, dropping the void fraction results in higher reactivity swing and therefore plummeting the safety factor of the reactor. (author)

  12. Feasibility study for the United Heckathorn Superfund Site, Richmond, California

    Energy Technology Data Exchange (ETDEWEB)

    Lincoff, A.H. [US Environmental Protection Agency, San Francisco, CA (United States). Region IX; Costan, G.P.; Montgomery, M.S.; White, P.J. [Pacific Northwest Lab., Richland, WA (United States)

    1994-07-01

    The United Heckathom Superfund Site in Richmond, California, was used to formulate pesticides from approximately 1947 to 1966. Soils at the site and sediments in the harbor were contaminated with various chlorinated pesticides, primarily DDT, as a result of these activities. The US Environmental Protection Agency listed the site on the Superfund National Priorities List in 1990. This document is part of the Remedial Investigation and Feasibility Study phase of the Superfund response, which will provide the basis for selection of a final remedy that will protect human health and the environment and achieve compliance with federal and state envirorunental laws.

  13. Report on feasibility study of the Clam Wave Energy Device

    Energy Technology Data Exchange (ETDEWEB)

    1979-04-01

    The main emphasis of the feasibility study has been towards producing an acceptable spine design for the Clam wave energy converter. Concrete and steel designs based on a mathematical model of the waveloading have been produced. Progress is also reported in the design of a bellows for a low-pressure air power transmission system. A narrow wave tank and scale model have been constructed in order to carry out a test programme on various aspects of the device's construction and performance.

  14. Feasibility study. Solar energy in Norway; Mulighetsstudie. Solenergi i Norge

    Energy Technology Data Exchange (ETDEWEB)

    Halvorsen, Una; Bernhard, Peter; Salvesen, Fritjof; Bugge, Lars; Andresen, Inger; Simonsen, Ingeborg

    2011-07-01

    On behalf of Enova KanEnergi and SINTEF summarized the results of the project 'Feasibility study. Solar energy' in a report. The purpose of this report is to outline an overview of the potential for solar energy in Norway to be realized until 2020. This is a survey of the status of technology and associated costs related to energy production, as well as a description of the market conditions. This report is a contribution to Enova's ongoing strategy and development. (eb)

  15. Feasibility Study of Biomass Electrical Generation on Tribal Lands

    Energy Technology Data Exchange (ETDEWEB)

    Tom Roche; Richard Hartmann; Joohn Luton; Warren Hudelson; Roger Blomguist; Jan Hacker; Colene Frye

    2005-03-29

    The goals of the St. Croix Tribe are to develop economically viable energy production facilities using readily available renewable biomass fuel sources at an acceptable cost per kilowatt hour ($/kWh), to provide new and meaningful permanent employment, retain and expand existing employment (logging) and provide revenues for both producers and sellers of the finished product. This is a feasibility study including an assessment of available biomass fuel, technology assessment, site selection, economics viability given the foreseeable fuel and generation costs, as well as an assessment of the potential markets for renewable energy.

  16. Feasibility Study for Operable Unit 7-13/14

    Energy Technology Data Exchange (ETDEWEB)

    K. Jean Holdren

    2007-05-29

    The Subsurface Disposal Area is a radioactive waste landfill located within the Radioactive Waste Management Complex at the Idaho National Laboratory Site in southeastern Idaho. This Feasibility Study for Operable Unit 7-13/14 analyzes options for mitigating risks to human health and the environment associated with the landfill. Analysis is conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act, using nine evaluation criteria to develop detailed and comparative analysis of five assembled alternatives. Assembled alternatives are composed of discrete modules. Ultimately, decision-makers will select, recombine, and sum various modules into an optimized preferred alternative and final remedial decision.

  17. Feasibility study for the United Heckathorn Superfund Site, Richmond, California

    International Nuclear Information System (INIS)

    Lincoff, A.H.

    1994-07-01

    The United Heckathom Superfund Site in Richmond, California, was used to formulate pesticides from approximately 1947 to 1966. Soils at the site and sediments in the harbor were contaminated with various chlorinated pesticides, primarily DDT, as a result of these activities. The US Environmental Protection Agency listed the site on the Superfund National Priorities List in 1990. This document is part of the Remedial Investigation and Feasibility Study phase of the Superfund response, which will provide the basis for selection of a final remedy that will protect human health and the environment and achieve compliance with federal and state envirorunental laws

  18. Technical feasibility study of 60 MWe fast reactor concept: RAPID

    International Nuclear Information System (INIS)

    Kambe, Mitsuru; Ueda, Nobuyuki; Uotani, Masaki

    1993-01-01

    A study has been performed on the passive safety features and technical feasibility of an inherently safe 60 MWe fast reactor concept RAPID to meet various power requirements in Japan. The system dynamic analyses on the UTOP and ULOF transients revealed that the enhanced reactivity feedback derived from an annular core configuration and the integrated fuel assembly provides a high margin of self-protection. Structural integrity of the integrated fuel assembly has also been confirmed. The following innovative key technologies have been demonstrated; Lithium Injection Modules (LIM) for ultimate shutdown, Lithium Expansion Modulus (LEM) for inherent reactivity feedback and Void Leading Channel (VLC) for the sodium void worth reduction. (author)

  19. Symplicity multi-electrode radiofrequency renal denervation system feasibility study.

    Science.gov (United States)

    Whitbourn, Robert; Harding, Scott A; Walton, Antony

    2015-05-01

    The aim of this study was to test the safety and performance of the Symplicity™ multi-electrode radio-frequency renal denervation system which was designed to reduce procedure time during renal denervation. The multi-electrode radiofrequency renal denervation system feasibility study is a prospective, non-randomised, open label, feasibility study that enrolled 50 subjects with hypertension. The study utilises a new renal denervation catheter which contains an array of four electrodes mounted in a helical configuration at 90 degrees from each other to deliver radiofrequency energy simultaneously to all four renal artery quadrants for 60 seconds. The protocol specified one renal denervation treatment towards the distal end of each main renal artery with radiofrequency energy delivered for 60 seconds per treatment. Total treatment time for both renal arteries was two minutes. The 12-month change in office systolic blood pressure (SBP) and 24-hour SBP was -19.2±25.2 mmHg, prenal artery stenosis or hypertensive emergencies occurred. The Symplicity multi-electrode radiofrequency renal denervation system was associated with a significant reduction in SBP at 12 months and minimal complications whilst it also reduced procedure time. NCT01699529.

  20. Feasibility Study for Cobalt Bundle Loading to CANDU Reactor Core

    International Nuclear Information System (INIS)

    Park, Donghwan; Kim, Youngae; Kim, Sungmin

    2016-01-01

    CANDU units are generally used to produce cobalt-60 at Bruce and Point Lepreau in Canada and Embalse in Argentina. China has started production of cobalt-60 using its CANDU 6 Qinshan Phase III nuclear power plant in 2009. For cobalt-60 production, the reactor’s full complement of stainless steel adjusters is replaced with neutronically equivalent cobalt-59 adjusters, which are essentially invisible to reactor operation. With its very high neutron flux and optimized fuel burn-up, the CANDU has a very high cobalt-60 production rate in a relatively short time. This makes CANDU an excellent vehicle for bulk cobalt-60 production. Several studies have been performed to produce cobalt-60 using adjuster rod at Wolsong nuclear power plant. This study proposed new concept for producing cobalt-60 and performed the feasibility study. Bundle typed cobalt loading concept is proposed and evaluated the feasibility to fuel management without physics and system design change. The requirement to load cobalt bundle to the core was considered and several channels are nominated. The production of cobalt-60 source is very depend on the flux level and burnup directly. But the neutron absorption characteristic of cobalt bundle is too high, so optimizing design study is needed in the future

  1. Feasibility Study for Cobalt Bundle Loading to CANDU Reactor Core

    Energy Technology Data Exchange (ETDEWEB)

    Park, Donghwan; Kim, Youngae; Kim, Sungmin [KHNP Central Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    CANDU units are generally used to produce cobalt-60 at Bruce and Point Lepreau in Canada and Embalse in Argentina. China has started production of cobalt-60 using its CANDU 6 Qinshan Phase III nuclear power plant in 2009. For cobalt-60 production, the reactor’s full complement of stainless steel adjusters is replaced with neutronically equivalent cobalt-59 adjusters, which are essentially invisible to reactor operation. With its very high neutron flux and optimized fuel burn-up, the CANDU has a very high cobalt-60 production rate in a relatively short time. This makes CANDU an excellent vehicle for bulk cobalt-60 production. Several studies have been performed to produce cobalt-60 using adjuster rod at Wolsong nuclear power plant. This study proposed new concept for producing cobalt-60 and performed the feasibility study. Bundle typed cobalt loading concept is proposed and evaluated the feasibility to fuel management without physics and system design change. The requirement to load cobalt bundle to the core was considered and several channels are nominated. The production of cobalt-60 source is very depend on the flux level and burnup directly. But the neutron absorption characteristic of cobalt bundle is too high, so optimizing design study is needed in the future.

  2. A feasibility study of educational tools for osteomalacia.

    Science.gov (United States)

    Waxman, R; Adebajo, A; Robinson, S; Walker, D; Johnson, M; Rahman, A; Samanta, A; Kumar, K; Raza, K; Helliwell, P

    2017-03-01

    Many people in the UK, particularly people of South Asian origin, are advised to supplement their vitamin D intake, yet most do not. This suggests an unmet educational need. The osteomalacia mind map was developed to meet this need. The mind map contains culturally sensitive images, translated into Urdu and made interactive on a DVD. This study explores the feasibility of a randomised controlled study to measure the effect of education on improving vitamin D knowledge and adherence. This was a pilot and feasibility study. Cluster randomisation was used to avoid inter person contamination. Two South Asian women's groups were recruited to receive information about osteomalacia either by interactive DVD or an Arthritis Research UK leaflet. Knowledge and compliance were tested before and after the educational interventions via a knowledge questionnaire and the measurement of vitamin D and parathormone levels. The groups were found to be mismatched for knowledge, educational attainment and language at baseline. There were also organisational difficulties and possible confounding due to different tutors and translators. The DVD group had high knowledge at baseline which did not improve. The leaflet group had low knowledge at baseline that did improve. The DVD group had lower parathormone which did not change. The leaflet group had an increase in vitamin D but parathormone remained high. Performing a randomised study with this population utilising an educational intervention was difficult to execute. If cluster randomisation is used, extreme care must be taken to match the groups at baseline.

  3. Solar feasibility study for site-specific industrial-process-heat applications. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Murray, O.L.

    1980-03-18

    This study addresses the technical feasibility of solar energy in industrial process heat (IPH) applications in Mid-America. The study was one of two contracted efforts covering the MASEC 12-state region comprised of: Illinois, Michigan, North Dakota, Indiana, Minnesota, Ohio, Iowa, Missouri, South Dakota, Kansas, Nebraska, Wisconsin. The results of our study are encouraging to the potential future role of solar energy in supplying process heat to a varied range of industries and applications. We identified and developed Case Study documentation of twenty feasible solar IPH applications covering eight major SIC groups within the Mid-American region. The geographical distribution of these applications for the existing range of solar insolation levels are shown and the characteristics of the applications are summarized. The results of the study include process identification, analysis of process heat requirements, selection of preliminary solar system characteristics, and estimation of system performance and cost. These are included in each of the 20 Case Studies. The body of the report is divided into two primary discussion sections dealing with the Study Methodology employed in the effort and the Follow-On Potential of the identified applications with regard to possible demonstration projects. The 20 applications are rated with respect to their relative overall viability and procedures are discussed for possible demonstration project embarkment. Also, a possible extension of this present feasibility study for late-comer industrial firms expressing interest appears worthy of consideration.

  4. Telephone Care Management of Fall Risk:: A Feasibility Study.

    Science.gov (United States)

    Phelan, Elizabeth A; Pence, Maureen; Williams, Barbara; MacCornack, Frederick A

    2017-03-01

    Care management has been found to be more effective than usual care for some chronic conditions, but few studies have tested care management for prevention of elder falls. This study aimed to assess the feasibility and preliminary efficacy of telephone care management of older adults presenting for medical attention due to a fall. The setting was an independent practice association in western Washington serving 1,300 Medicare Advantage-insured patients. Patients aged ≥65 years treated for a fall in an emergency department or their primary care provider's office were contacted via telephone by a care manager within 48 hours of their fall-related visit and invited to participate in a telephone-administered interview to identify modifiable fall risk factors and receive recommendations and follow-up to address identified risk factors. Data from care manager records, patient medical records, and healthcare claims for the first 6 months (November 2009-April 2010) of program implementation were analyzed in 2011. The feasibility of screening and management of fall risk factors over the telephone and the effect on medically attended falls were assessed. Twenty-two patients eligible for fall care management were reached and administered the protocol. Administration took 15-20 minutes and integrated easily with the care manager's other responsibilities. Follow-through on recommendations varied, from 45% for those for whom exercise participation was recommended to 100% for other recommendations. No medically attended falls occurred over 6 months of follow-up. Telephone care management of fall risk appears feasible and may reduce falls requiring medical attention. Copyright © 2016 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

  5. Harvest for health gardening intervention feasibility study in cancer survivors.

    Science.gov (United States)

    Blair, Cindy K; Madan-Swain, Avi; Locher, Julie L; Desmond, Renee A; de Los Santos, Jennifer; Affuso, Olivia; Glover, Tony; Smith, Kerry; Carley, Joseph; Lipsitz, Mindy; Sharma, Ayushe; Krontiras, Helen; Cantor, Alan; Demark-Wahnefried, Wendy

    2013-08-01

    Cancer survivors are at increased risk for second malignancies, cardiovascular disease, diabetes, and functional decline. Evidence suggests that a healthful diet and physical activity may reduce the risk of chronic disease and improve health in this population. We conducted a feasibility study to evaluate a vegetable gardening intervention that paired 12 adult and child cancer survivors with Master Gardeners to explore effects on fruit and vegetable intake, physical activity, quality-of-life, and physical function. Throughout the year-long study period, the survivor-Master Gardener dyads worked together to plan/plant three gardens, harvest/rotate plantings, and troubleshoot/correct problems. Data on diet, physical activity, and quality-of-life were collected via surveys; anthropometrics and physical function were objectively measured. Acceptability of the intervention was assessed with a structured debriefing survey. The gardening intervention was feasible (robust enrollment; minimal attrition) and well-received by cancer survivors and Master Gardeners. Improvement in three of four objective measures of strength, agility, and endurance was observed in 90% of survivors, with the following change scores [median (interquartile range)] noted between baseline and one-year follow-up: hand grip test [+ 4.8 (3.0, 6.7) kg], 2.44 meter Get-Up-and-Go [+ 1.0 (+ 1.8, + 0.2) seconds], 30-second chair stand [+ 3.0 (+ 1.0, 5.0) stands], and six-minute walk [+ 11.6 (6.1, 48.8) meters]. Increases of ≥ 1 fruit and vegetable serving/day and ≥ 30 minutes/week of physical activity were observed in 40% and 60%, respectively. These preliminary results support the feasibility and acceptability of a mentored gardening intervention and suggest that it may offer a novel and promising strategy to improve fruit and vegetable consumption, physical activity, and physical function in cancer survivors. A larger randomized controlled trial is needed to confirm our results.

  6. Economic and technical feasibility study of compressed air storage

    Energy Technology Data Exchange (ETDEWEB)

    1976-03-01

    The results of a study of the economic and technical feasibility of compressed air energy storage (CAES) are presented. The study, which concentrated primarily on the application of underground air storage with combustion turbines, consisted of two phases. In the first phase a general assessment of the technical alternatives, economic characteristics and the institutional constraints associated with underground storage of compressed air for utility peaking application was carried out. The goal of this assessment was to identify potential barrier problems and to define the incentive for the implementation of compressed air storage. In the second phase, the general conclusions of the assessment were tested by carrying out the conceptual design of a CAES plant at two specific sites, and a program of further work indicated by the assessment study was formulated. The conceptual design of a CAES plant employing storage in an aquifer and that of a plant employing storage in a conventionally excavated cavern employing a water leg to maintain constant pressure are shown. Recommendations for further work, as well as directions of future turbo-machinery development, are made. It is concluded that compressed air storage is technically feasible for off-peak energy storage, and, depending on site conditions, CAES plants may be favored over simple cycle turbine plants to meet peak demands. (LCL)

  7. Feasibility Study Analysis of Establishing Archery Sports Special Place

    Science.gov (United States)

    Tarigan, U. P. P.; Mardhatillah, A.; Budiman, I.; Sembiring, A. C.; Ramadhan, M. S.

    2018-04-01

    This study essentially discusses the basic concepts related to the decision and process of selecting a sports archery business project in order to provide economic and social benefits over time. Archery sports is a sport that requires special skills, both accuracy, coordination mental training and improves the physical condition of the prime. In Medan, it's still a bit of practice archery, but many people love this sport. From the data collected, there are three locations where archery in the city of the field of the Sunggal Knights is located at Jl Tunggul Hitam no.1A, Kec. Medan Sunggal, Avros Educational Park Aval address at Avros Street No.60 Medan, and the Knights of Johor Archery Club which is located at Jl. The work of Darma Gg. Ujung Family, Medan Johor. Therefore a feasibility study was undertaken in establishing an archery sports place in the field. The aspects to be considered in making feasibility studies are market and marketing aspects, technical and equipment aspects, management aspects, legal aspects, economic and social aspects, and financial aspects. Financial analysis using own capital got Payback Period 3 years 5,8 months, Net Present Value Rp 11.684.026 and obtained Internal Rate of Return of 17%.

  8. Assessment of apical periodontitis by MRI. A feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Geibel, M.A. [Ulm Univ. (Germany). Oral and Maxillofacial Surgery; Schreiber, E.S.; Bracher, A.K.; Rasche, V. [Ulm Univ. (Germany). Internal Medicine II; Hell, E.; Ulrici, J. [Sirona Dental Systems GmbH, Bensheim (Germany). Dental Imaging; Sailer, L.K. [DOC Praxisklinik im Wiley, Neu-Ulm (Germany). MKG; Ozpeynirci, Y. [Ulm Univ. (Germany). Diagnostic and Interventional Radiology

    2015-04-15

    The purpose of this clinical feasibility study was to evaluate the applicability of magnetic resonance imaging (MRI) for the assessment of apical periodontitis in direct comparison with cone beam CT (CBCT). 19 consecutive patients (average age 43 ± 13 years) with 34 lesions in total (13 molars, 14 premolars and 7 front teeth) were enrolled in this feasibility study. Periapical lesions were defined as periapical radiolucencies (CBCT) or structural changes in the spongy bone signal (MRI), which were connected with the apical part of a root and with at least twice the width of the periodontal ligament space. The location and dimension of the lesions were compared between MRI and CBCT. While mainly mineralized tissue components such as teeth and bone were visible with CBCT, complimentary information of the soft tissue components was assessable with MRI. The MRI images provided sufficient diagnostic detail for the assessment of the main structures of interest. Heterogeneous contrast was observed within the lesion, with often a clear enhancement close to the apical foramen and the periodontal gap. No difference for lesion visibility was observed between MRI and CBCT. The lesion dimensions corresponded well, but were slightly but significantly overestimated with MRI. A heterogeneous lesion appearance was observed in several patients. Four patients presented with a well circumscribed hyperintense signal in the vicinity of the apical foramen. The MRI capability of soft tissue characterization may facilitate detailed analysis of periapical lesions. This clinical study confirms the applicability of multi-contrast MRI for the identification of periapical lesions.

  9. Mindfulness and Climate Change Action: A Feasibility Study

    Directory of Open Access Journals (Sweden)

    Maggie Grabow

    2018-05-01

    Full Text Available Pro-environmental behaviors and the cultural shifts that can accompany these may offer solutions to the consequences of a changing climate. Mindfulness has been proposed as a strategy to initiate these types of behaviors. In 2017, we pilot-tested Mindful Climate Action (MCA, an eight-week adult education program that delivers energy use, climate change, and sustainability content in combination with training in mindfulness meditation, among 16 individuals living in Madison, WI. We collected participant data at baseline and at different times across the study period regarding household energy use, transportation, diet, and health and happiness. This pilot study aimed to evaluate the feasibility of the various MCA study practices including measurement tools, outcome assessment, curriculum and related educational materials, and especially the mindfulness-based climate action trainings. MCA was well-received by participants as evidenced by high adherence rate, high measures of participant satisfaction, and high participant response rate for surveys. In addition, we successfully demonstrated feasibility of the MCA program, and have estimated participant’s individual carbon footprints related to diet, transportation, and household energy.

  10. Assessment of apical periodontitis by MRI. A feasibility study

    International Nuclear Information System (INIS)

    Geibel, M.A.; Schreiber, E.S.; Bracher, A.K.; Rasche, V.; Hell, E.; Ulrici, J.; Sailer, L.K.; Ozpeynirci, Y.

    2015-01-01

    The purpose of this clinical feasibility study was to evaluate the applicability of magnetic resonance imaging (MRI) for the assessment of apical periodontitis in direct comparison with cone beam CT (CBCT). 19 consecutive patients (average age 43 ± 13 years) with 34 lesions in total (13 molars, 14 premolars and 7 front teeth) were enrolled in this feasibility study. Periapical lesions were defined as periapical radiolucencies (CBCT) or structural changes in the spongy bone signal (MRI), which were connected with the apical part of a root and with at least twice the width of the periodontal ligament space. The location and dimension of the lesions were compared between MRI and CBCT. While mainly mineralized tissue components such as teeth and bone were visible with CBCT, complimentary information of the soft tissue components was assessable with MRI. The MRI images provided sufficient diagnostic detail for the assessment of the main structures of interest. Heterogeneous contrast was observed within the lesion, with often a clear enhancement close to the apical foramen and the periodontal gap. No difference for lesion visibility was observed between MRI and CBCT. The lesion dimensions corresponded well, but were slightly but significantly overestimated with MRI. A heterogeneous lesion appearance was observed in several patients. Four patients presented with a well circumscribed hyperintense signal in the vicinity of the apical foramen. The MRI capability of soft tissue characterization may facilitate detailed analysis of periapical lesions. This clinical study confirms the applicability of multi-contrast MRI for the identification of periapical lesions.

  11. Fusion Guidance in Endovascular Peripheral Artery Interventions: A Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Sailer, Anna M., E-mail: anni.sailer@mumc.nl; Haan, Michiel W. de, E-mail: m.de.haan@mumc.nl; Graaf, Rick de, E-mail: r.de.graaf@mumc.nl; Zwam, Willem H. van, E-mail: w.van.zwam@mumc.nl [Maastricht University Medical Center, Department of Radiology (Netherlands); Schurink, Geert Willem H., E-mail: gwh.schurink@mumc.nl [Maastricht University Medical Center, Department of Surgery (Netherlands); Nelemans, Patricia J., E-mail: patty.nelemans@maastrichtuniversity.nl [Maastricht University Medical Centre, Department of Epidemiology (Netherlands); Wildberger, Joachim E., E-mail: j.wildberger@mumc.nl; Das, Marco, E-mail: m.das@mumc.nl [Maastricht University Medical Center, Department of Radiology (Netherlands)

    2015-04-15

    PurposeThis study was designed to evaluate the feasibility of endovascular guidance by means of live fluoroscopy fusion with magnetic resonance angiography (MRA) and computed tomography angiography (CTA).MethodsFusion guidance was evaluated in 20 endovascular peripheral artery interventions in 17 patients. Fifteen patients had received preinterventional diagnostic MRA and two patients had undergone CTA. Time for fluoroscopy with MRA/CTA coregistration was recorded. Feasibility of fusion guidance was evaluated according to the following criteria: for every procedure the executing interventional radiologists recorded whether 3D road-mapping provided added value (yes vs. no) and whether PTA and/or stenting could be performed relying on the fusion road-map without need for diagnostic contrast-enhanced angiogram series (CEAS) (yes vs. no). Precision of the fusion road-map was evaluated by recording maximum differences between the position of the vasculature on the virtual CTA/MRA images and conventional angiography.ResultsAverage time needed for image coregistration was 5 ± 2 min. Three-dimensional road-map added value was experienced in 15 procedures in 12 patients. In half of the patients (8/17), intervention was performed relying on the fusion road-map only, without diagnostic CEAS. In two patients, MRA roadmap showed a false-positive lesion. Excluding three patients with inordinate movements, mean difference in position of vasculature on angiography and MRA/CTA road-map was 1.86 ± 0.95 mm, implying that approximately 95 % of differences were between 0 and 3.72 mm (2 ± 1.96 standard deviation).ConclusionsFluoroscopy with MRA/CTA fusion guidance for peripheral artery interventions is feasible. By reducing the number of CEAS, this technology may contribute to enhance procedural safety.

  12. Feasibility study of an attention training application for older adults.

    Science.gov (United States)

    Hill, Nikki L; Mogle, Jacqueline; Colancecco, Elise; Dick, Robert; Hannan, John; Lin, Feng Vankee

    2015-09-01

    Technology-based attention training has demonstrated promise in its potential to improve cognitive functioning in older people. Developing mobile applications, with older users specifically in mind, may support future dissemination of these interventions and integration into daily life. The purpose of this pilot study was to test the feasibility of an Attention Training Application (ATA) for community-dwelling older adults using mobile technology. A descriptive, mixed-methods design was used to capture older adults' feedback on the usability and acceptability of the ATA. A convenience sample of older adults (n = 9) from two independent living facilities participated in a 2-hour training and practice session with the ATA. Participants were given personally tailored instructions for using the mobile device and the ATA specifically. Following a practice session, participants provided ratings on multiple components of the ATA and completed an audio-recorded, semi-structured interview to provide detailed descriptions of their experience and perceptions. An iterative process of content analysis was used to characterise the open-ended responses. Participants rated the ATA favourably overall on several 0-10 scales including likeability [8.5 (1.6)], interest [8.8 (2.3)] and satisfaction [8.2 (1.9)]. The qualitative analyses revealed several issues relevant to the feasibility of the ATA among older people including the importance of the technological background of the user, limiting negative feedback, challenges with the touch screen interface, personal preferences for challenge, extending the practice period and the difficulty of the dual-task condition. The use of the ATA is feasible in the older adult population. Future development should specifically consider personal characteristics as well as preferences to maximise usability and acceptability among older people. Older adults enjoyed the ATA. This opens doors to user-friendly technological interventions that may be

  13. Fusion Guidance in Endovascular Peripheral Artery Interventions: A Feasibility Study

    International Nuclear Information System (INIS)

    Sailer, Anna M.; Haan, Michiel W. de; Graaf, Rick de; Zwam, Willem H. van; Schurink, Geert Willem H.; Nelemans, Patricia J.; Wildberger, Joachim E.; Das, Marco

    2015-01-01

    PurposeThis study was designed to evaluate the feasibility of endovascular guidance by means of live fluoroscopy fusion with magnetic resonance angiography (MRA) and computed tomography angiography (CTA).MethodsFusion guidance was evaluated in 20 endovascular peripheral artery interventions in 17 patients. Fifteen patients had received preinterventional diagnostic MRA and two patients had undergone CTA. Time for fluoroscopy with MRA/CTA coregistration was recorded. Feasibility of fusion guidance was evaluated according to the following criteria: for every procedure the executing interventional radiologists recorded whether 3D road-mapping provided added value (yes vs. no) and whether PTA and/or stenting could be performed relying on the fusion road-map without need for diagnostic contrast-enhanced angiogram series (CEAS) (yes vs. no). Precision of the fusion road-map was evaluated by recording maximum differences between the position of the vasculature on the virtual CTA/MRA images and conventional angiography.ResultsAverage time needed for image coregistration was 5 ± 2 min. Three-dimensional road-map added value was experienced in 15 procedures in 12 patients. In half of the patients (8/17), intervention was performed relying on the fusion road-map only, without diagnostic CEAS. In two patients, MRA roadmap showed a false-positive lesion. Excluding three patients with inordinate movements, mean difference in position of vasculature on angiography and MRA/CTA road-map was 1.86 ± 0.95 mm, implying that approximately 95 % of differences were between 0 and 3.72 mm (2 ± 1.96 standard deviation).ConclusionsFluoroscopy with MRA/CTA fusion guidance for peripheral artery interventions is feasible. By reducing the number of CEAS, this technology may contribute to enhance procedural safety

  14. Fusion guidance in endovascular peripheral artery interventions: a feasibility study.

    Science.gov (United States)

    Sailer, Anna M; de Haan, Michiel W; de Graaf, Rick; van Zwam, Willem H; Schurink, Geert Willem H; Nelemans, Patricia J; Wildberger, Joachim E; Das, Marco

    2015-04-01

    This study was designed to evaluate the feasibility of endovascular guidance by means of live fluoroscopy fusion with magnetic resonance angiography (MRA) and computed tomography angiography (CTA). Fusion guidance was evaluated in 20 endovascular peripheral artery interventions in 17 patients. Fifteen patients had received preinterventional diagnostic MRA and two patients had undergone CTA. Time for fluoroscopy with MRA/CTA coregistration was recorded. Feasibility of fusion guidance was evaluated according to the following criteria: for every procedure the executing interventional radiologists recorded whether 3D road-mapping provided added value (yes vs. no) and whether PTA and/or stenting could be performed relying on the fusion road-map without need for diagnostic contrast-enhanced angiogram series (CEAS) (yes vs. no). Precision of the fusion road-map was evaluated by recording maximum differences between the position of the vasculature on the virtual CTA/MRA images and conventional angiography. Average time needed for image coregistration was 5 ± 2 min. Three-dimensional road-map added value was experienced in 15 procedures in 12 patients. In half of the patients (8/17), intervention was performed relying on the fusion road-map only, without diagnostic CEAS. In two patients, MRA roadmap showed a false-positive lesion. Excluding three patients with inordinate movements, mean difference in position of vasculature on angiography and MRA/CTA road-map was 1.86 ± 0.95 mm, implying that approximately 95 % of differences were between 0 and 3.72 mm (2 ± 1.96 standard deviation). Fluoroscopy with MRA/CTA fusion guidance for peripheral artery interventions is feasible. By reducing the number of CEAS, this technology may contribute to enhance procedural safety.

  15. Trans-Caspian gas pipeline feasibility study. Volume 3

    International Nuclear Information System (INIS)

    1999-01-01

    This study, conducted by Enron Engineering and Construction Company, was funded by the US Trade and Development Agency. The study provides detailed information concerning natural gas demand in Turkey and Southern Europe. The purpose of the study is to estimate the rate at which new gas can be absorbed in the Turkish market and be re-exported to the markets in Europe, as well as to forecast Turkish natural gas demand for the period up to 2020. The study also evaluates gas demand and pricing for the market in the 2002--2005 time frame. This is Volume 3 of a 3-volume report, and it is divided into the following sections: (1) Executive Summary; (2) Task C: Technical Feasibility and Preliminary Design; (3) Task F: Project Implementation Strategy

  16. Feasibility study report for Operable Unit 4: Volume 1

    International Nuclear Information System (INIS)

    1994-02-01

    This report documents the Feasibility Study (FS) phase of the Fernald Environmental Management Project (FEMP) Operable Unit 4 Remedial Investigation/Feasibility Study (RI/FS) Program. The FEMP, formerly known as the Feed Materials Production Center (FMPC), is a US Department of Energy (DOE) facility that operated from 1952 to 1989. The facility's primarily function was to provide high purity uranium metal products to support United States defense programs. Production operations were suspended in 1989 to focus on environmental restoration and waste management activities at the facility. The RI/FS is being conducted pursuant to the terms of a Consent Agreement between DOE and the US Environmental Protection Agency (EPA) under Sections 120 and 106(a) of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. The Ohio Environmental Protection Agency (OEPA) is also participating in the RI/FS process at the FEMP through direct involvement in program review meetings and technical review of project documentation. The objective of the RI/FS process is to gather information to support an informed risk management decision regarding which remedy appears to be the most appropriate action for addressing the environmental concerns identified at the FEMP

  17. Feasibility study report for Operable Unit 4: Volume 2

    International Nuclear Information System (INIS)

    1994-02-01

    This report documents the Feasibility Study (FS) phase of the Fernald Environmental Management Project (FEMP) Operable Unit 4 Remedial Investigation/Feasibility Study (RI/FS) Program. The FEMP, formerly known as the Feed Materials Production Center (FMPC), is a US Department of Energy (DOE) facility that operated from 1952 to 1989. The facility's primarily function was to provide high purity uranium metal products to support United States defense programs. Production operations were suspended in 1989 to focus on environmental restoration and waste management activities at the facility. The RI/FS is being conducted pursuant to the terms of a Consent Agreement between DOE and the US Environmental Protection Agency (EPA) under Sections 120 and 106(a) of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. The Ohio Environmental Protection Agency (OEPA) is also participating in the RI/FS process at the FEMP through direct involvement in program review meetings and technical review of project documentation. The objective of the RI/FS process is to gather information to support an informed risk management decision regarding which remedy appears to be the most appropriate action for addressing the environmental concerns identified at the FEMP. This volume contains appendices A--E

  18. 100-KR-1 Operable Unit focused feasibility study report

    International Nuclear Information System (INIS)

    1994-11-01

    The standard Comprehensive Environmental Response, Compensation, and Liability Act of 1980 Feasibility Study (FS) includes development and screening of alternatives and the detailed analysis of alternatives. This focused feasibility study (FFS) was conducted for the 100-KR-1 Operable Unit at the Hanford Site in southeastern Washington. The objective of this operable unit-specific FFS is to provide decision makers with sufficient information to allow appropriate and timely selection of interim remedial measures (IRM) for the five sites (116-K-1 crib, 116-K-2 trench, 116-KE-4 and 116-KW-3 retention basins, and process effluent pipelines) associated with the 100-KR-1 Operable Unit. The IRM candidate waste sites are determined in the limited field investigation. Site profiles are developed for each of these waste site. The site profiles are used in the application of the plug-in approach. The waste site either plugs into the analysis of the alternatives for the group, or deviations from the developed group alternatives are described and documented

  19. Cadaveric surgery in core gynaecology training: a feasibility study.

    Science.gov (United States)

    Lim, Chou Phay; Roberts, Mark; Chalhoub, Tony; Waugh, Jason; Delegate, Laura

    2018-01-01

    Fresh frozen cadaver training has been proposed as a better model than virtual reality simulators in laparoscopy training. We aimed to explore the relationship between cadaveric surgical training and increased surgical confidence.To determine feasibility, we devised two 1-day cadaveric surgical training days targeted at trainees in obstetrics and gynaecology. Seven defined surgical skills were covered during the course of the day. The relationship between surgical training and surgical confidence was explored using both quantitative (confidence scores) and qualitative tools (questionnaires). Participants rated a consistent improvement in their level of confidence after the training. They universally found the experience positive and three overarching themes emerged from the qualitative analysis including self-concept, social persuasion and stability of task. It is pragmatically feasible to provide procedure-specific cadaveric surgical training alongside supervised clinical training. This small, non-generalisable study suggests that cadaveric training may contribute to an increase in surgical self-confidence and efficacy. This will form the basis of a larger study and needs to be explored in more depth with a larger population.

  20. Feasibility Study of Laser Cutting for Fabrication of Tensile Specimen

    International Nuclear Information System (INIS)

    Jin, Y. G.; Baik, S. J.; Kim, G. S.; Heo, G. S.; Yoo, B. O.; Ahn, S. B.; Chun, Y. B.

    2015-01-01

    The specimen fabrication technique was established to machine the specimen from the irradiated materials. The wire cut EDM(electric discharge machine) was modified to fabricate the mechanical testing specimens from irradiated components and fuel claddings. The oxide layer removal system was also developed because the oxide layer on the surface of the irradiated components and claddings interrupted the applying the electric current during the processing. However, zirconium oxide is protective against further corrosion as well as beneficial to mechanical strength for the tensile deformation of the cladding. Thus, it is important to fabricate the irradiated specimens without removal of oxide layer on the surface of the irradiated structural components and claddings. In the present study, laser cutting system was introduced to fabricate the various mechanical testing specimens from the unirradiated fuel cladding and the feasibility of the laser cutting system was studied for the fabrication of various types of irradiated specimens in a hot cell at IMEF (Irradiated Materials Examination Facility) of KAERI. Laser beam machining system was introduced to fabricate the various mechanical testing specimens from the unirradiated fuel cladding and the dimensions were compared for the feasibility of the laser cutting system. The effect of surface oxide layer was also investigated for machining process of the zircaloy-4 fuel cladding and it was found that laser beam machining could be a useful tool to fabricate the specimens with surface oxide layer

  1. Feasibility Study of Laser Cutting for Fabrication of Tensile Specimen

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Y. G.; Baik, S. J.; Kim, G. S.; Heo, G. S.; Yoo, B. O.; Ahn, S. B.; Chun, Y. B. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    The specimen fabrication technique was established to machine the specimen from the irradiated materials. The wire cut EDM(electric discharge machine) was modified to fabricate the mechanical testing specimens from irradiated components and fuel claddings. The oxide layer removal system was also developed because the oxide layer on the surface of the irradiated components and claddings interrupted the applying the electric current during the processing. However, zirconium oxide is protective against further corrosion as well as beneficial to mechanical strength for the tensile deformation of the cladding. Thus, it is important to fabricate the irradiated specimens without removal of oxide layer on the surface of the irradiated structural components and claddings. In the present study, laser cutting system was introduced to fabricate the various mechanical testing specimens from the unirradiated fuel cladding and the feasibility of the laser cutting system was studied for the fabrication of various types of irradiated specimens in a hot cell at IMEF (Irradiated Materials Examination Facility) of KAERI. Laser beam machining system was introduced to fabricate the various mechanical testing specimens from the unirradiated fuel cladding and the dimensions were compared for the feasibility of the laser cutting system. The effect of surface oxide layer was also investigated for machining process of the zircaloy-4 fuel cladding and it was found that laser beam machining could be a useful tool to fabricate the specimens with surface oxide layer.

  2. Feasibility study for the European Reliability Data System (ERDS)

    International Nuclear Information System (INIS)

    Mancini, G.

    1980-01-01

    In the framework of the Reactor Safety Programme of the Commission of the European Communities, the JRC - Ispra Establishment has performed a feasibility study for an integrated European Reliability Data System, the aim of which is the collection and organization of information related to the operation of LWRs with regard to component and systems behaviour, abnormal occurrences, outages, etc. Component Event Data Bank (CEGB), Abnormal Occurrences Reporting System, Generic Reliability Parameter Data Bank, Operating Unit Status Reports and the main activities carried out during the last two years are described. The most important achievements are briefly reported, such as: Reference Classification for Systems, Components and Failure Events, Informatic Structure of the Pilot Experiment of the CEDB, Information Retrieval System for Abnormal Occurrences Reports, Data Bank on Component Reliability Parameters, System on the Exchange of Operation Experience of LWRs, Statistical Data Treatment. Finally, the general conclusions of the feasibility study are summarized: the possibility and the usefulness for the creation of an integrated European Reliability Data System are outlined. (author)

  3. Prevention of anxiety disorders in primary care: A feasibility study

    Directory of Open Access Journals (Sweden)

    Batelaan Neeltje M

    2012-11-01

    Full Text Available Abstract Background Anxiety disorders are highly prevalent in primary care and cause a substantial burden of disease. Screening on risk status, followed by preventive interventions in those at risk may prevent the onset of anxiety disorders, and thereby reduce the disease burden. The willingness to participate in screening and interventions is crucial for the scope of preventive strategies, but unknown. This feasibility study, therefore, investigated participation rates of screening and preventive services for anxiety disorders in primary care, and explored reasons to refrain from screening. Methods In three general practices, screening was offered to individuals visiting their general practitioner (total n = 2454. To assess risk status, a 10-item questionnaire was followed by a telephone interview (including the CIDI when scoring above a predefined threshold. Preventive services were offered to those at risk. Participation rates for screening and preventive services for anxiety disorders were assessed. Those not willing to be screened were asked for their main reason to refrain from screening. Results Of all individuals, 17.3% participated in initial screening, and of those with a possible risk status, 56.0% continued screening. In 30.1% of those assessed, a risk status to develop an anxiety disorder was verified. Of these, 22.6% already received some form of mental health treatment and 38.7% of them agreed to participate in a preventive intervention and were referred. The most frequently mentioned reasons to refrain from screening were the emotional burden associated with elevated risk status, the assumption not to be at risk, and a lack of motivation to act upon an elevated risk status by using preventive services. Conclusions Screening in general practice, followed by offering services to prevent anxiety disorders in those at risk did not appear to be a feasible strategy due to low participation rates. To enable the development of

  4. Battery energy storage market feasibility study - Expanded report

    International Nuclear Information System (INIS)

    Kraft, S.; Akhil, A.

    1997-09-01

    Under the sponsorship of the US Department of Energy's Office of Utility Technologies, the Energy Storage Systems Analysis and Development Department at Sandia National Laboratories (SNL) contracted Frost and Sullivan to conduct a market feasibility study of energy storage systems. The study was designed specifically to quantify the battery energy storage market for utility applications. This study was based on the SNL Opportunities Analysis performed earlier. Many of the groups surveyed, which included electricity providers, battery energy storage vendors, regulators, consultants, and technology advocates, viewed battery storage as an important technology to enable increased use of renewable energy and as a means to solve power quality and asset utilization issues. There are two versions of the document available, an expanded version (approximately 200 pages, SAND97-1275/2) and a short version (approximately 25 pages, SAND97-1275/1)

  5. Technological feasibility studies on combination treatments for subtropical fruits

    International Nuclear Information System (INIS)

    Brodrick, H.T.; Linde, H.J. van der

    1981-01-01

    Research with subtropical fruits such as papayas and mangoes had advanced beyond the experimental stage in South Africa. This may be attributed to the potential economic benefits likely to be obtained from the combination of heat and irradiation treatments. The outcome of recent marketing trials, however, revealed several problem areas which need further investigation. Some of these problems were studied in greater detail and are reported in this presentation. The effect of time delays between hot-water and irradiation treatments on the efficacy in disease control in the fruit, has received particular attention in the investigations. Efforts have also been made to correlate these results with those obtained in fungal studies in the laboratory. These and other factors relating to the technological feasibility in the use of combined treatments for the preservation of mangoes and papayas are discussed and recommendations or guidelines for future studies are given in this paper. (author)

  6. Battery energy storage market feasibility study -- Expanded report

    Energy Technology Data Exchange (ETDEWEB)

    Kraft, S. [Frost and Sullivan, Mountain View, CA (United States); Akhil, A. [Sandia National Labs., Albuquerque, NM (United States). Energy Storage Systems Analysis and Development Dept.

    1997-09-01

    Under the sponsorship of the US Department of Energy`s Office of Utility Technologies, the Energy Storage Systems Analysis and Development Department at Sandia National Laboratories (SNL) contracted Frost and Sullivan to conduct a market feasibility study of energy storage systems. The study was designed specifically to quantify the battery energy storage market for utility applications. This study was based on the SNL Opportunities Analysis performed earlier. Many of the groups surveyed, which included electricity providers, battery energy storage vendors, regulators, consultants, and technology advocates, viewed battery storage as an important technology to enable increased use of renewable energy and as a means to solve power quality and asset utilization issues. There are two versions of the document available, an expanded version (approximately 200 pages, SAND97-1275/2) and a short version (approximately 25 pages, SAND97-1275/1).

  7. A feasibility study for a manufacturing technology deployment center

    Energy Technology Data Exchange (ETDEWEB)

    1994-10-31

    The Automation & Robotics Research Institute (ARRI) and the Texas Engineering Extension Service (TEEX) were funded by the U.S. Department of Energy to determine the feasibility of a regional industrial technology institute to be located at the Superconducting Super Collider (SSC) Central Facility in Waxahachie, Texas. In response to this opportunity, ARRI and TEEX teamed with the DOE Kansas City Plant (managed by Allied Signal, Inc.), Los Alamos National Laboratory (managed by the University of California), Vought Aircraft Company, National Center for Manufacturing Sciences (NCMS), SSC Laboratory, KPMG Peat Marwick, Dallas County Community College, Navarro Community College, Texas Department of Commerce (TDOC), Texas Manufacturing Assistance Center (TMAC), Oklahoma Center for the Advancement of Science and Technology, Arkansas Science and Technology Authority, Louisiana Productivity Center, and the NASA Mid-Continent Technology Transfer Center (MCTTC) to develop a series of options, perform the feasibility analysis and secure industrial reviews of the selected concepts. The final report for this study is presented in three sections: Executive Summary, Business Plan, and Technical Plan. The results from the analysis of the proposed concept support the recommendation of creating a regional technology alliance formed by the states of Texas, New Mexico, Oklahoma, Arkansas and Louisiana through the conversion of the SSC Central facility into a Manufacturing Technology Deployment Center (MTDC).

  8. Feasibility study for an alternative PWR-containment. Stage 3

    International Nuclear Information System (INIS)

    Eibl, J.

    1994-08-01

    The following report deals with a feasibility study on a lightwater reactor containment which is oriented at the German 1300 MW Convoy Type reactor. It was the aim of this containment development for a future nuclear ractor to restrict all consequences of an extreme reactor failure exclusively to the interior of the containment. Also the decay heat of the relevant core catchers is provided to be removed by passive means. This containment development was a common project with the Nuclear Research Centre at Karlsruhe (KFK). As a consequence of this intention the concept started from upper physical limits, such as a maximum static pressure of 1,5 MPa at 200 , a global and local detonation pressure of 8,4 MPa at an impulse of 5,0 kPas, an upward directed force exerted by the pressure vessel of 300 MN, a horizontal force exerted by the moving pressure vessel onto its environment of 70 MN, a cavern pressure around the core catcher of 3,0 resp., 2,0 MPa and a steam explosion-energy of 300 MJ. Such a contaiment concept is presented and inverstigated with respect to its feasibility, statically and dynamically in all relevant details including earthquake actions. (orig.) [de

  9. Anticipatory precrash restraint sensor feasibility study: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kercel, S.W.; Dress, W.B.

    1995-08-01

    This report explores feasibility of an anticipatory precrash restraint sensor. The foundation principle is the anticipation mechanism found at a primitive level of biological intelligence and originally formalized by the mathematical biologist Robert Rosen. A system based on formal anticipatory principles should significantly outperform conventional technologies. It offers the prospect of high payoff in prevention of death and injury. Sensors and processes are available to provide a good, fast, and inexpensive description of the present dynamical state of the vehicle to the embedded system model in the anticipation engine. The experimental part of this study found that inexpensive radar in a real-world setting does return useful data on target dynamics. The data produced by a radar system can be converted to target dynamical information by good, fast and inexpensive signal-processing techniques. Not only is the anticipatory sensor feasible, but further development under the sponsorship of the National Highway Traffic Safety Administration is necessary and desirable. There are a number of possible lines of follow-on investigation. The level of effort and expected benefits of various alternatives are discussed.

  10. Feasibility studies of radiation sterilization of some pharmaceutical products

    International Nuclear Information System (INIS)

    Gopal, N.G.S.; Rajagopalan, S.; Sharma, G.

    1975-01-01

    The paper deals with some studies carried out to evaluate the feasibility of radiation sterilization or treatment of some medical products and pharmaceuticals of immediate importance to their respective industries. The products include penicillin G sodium, ampicillin sodium, tetracyclin hydrochloride ointment,hydrocortisone acetate and its ointment, aqueous sodium chloride solutions (0.9 and 20%), fluorescein sodium strips, urea, ethylmorphine hydrochloride, aqueous solution of chlorobutanol and one of its commercial preparations, phenylmercuric nitrate and its aqueous solutions, aqueous solutions of methyl and propyl paraben, lactose, gum karaya, absorbent cotton and poly-(vinyl chloride) based medical products. The irradiated products have been examined for pharmacopoeial specifications wherever available. In general the products have been examined for changes in colour, pH, ultra-violet and infra-red absorption spectra. Thin-layer chromatographic analyses have been carried out to establish the purity of some of the irradiated products. The feasibility or otherwise of radiation sterilization or treatment of the various products from the physicochemical and microbiological (pharmacological) clinical considerations is also described. (author)

  11. Oak Ridge National Laboratory remedial investigation/feasibility study

    International Nuclear Information System (INIS)

    Glenn, R.D.; Hoffman, J.M.; Hyde, L.D.

    1988-01-01

    The Oak Ridge National Laboratory (ORNL) Remedial Investigation/ Feasibility Study (RI/FS) began in June 1987 to evaluate 13 contaminated waste area groupings (WAGs) to determine the feasibility and benefits of potential remedial action. The RI/FS and any future remedial action at ORNL will be of national significance and will likely lead to developments that will become models for environmental investigations and cleanups. Bechtel National, Inc. and a team of subcontractors will be working with Martin Marietta Energy systems to conduct intensive field investigations to obtain data required to evaluate the WAGs. The RI/F project continued in FY 1988 with project planning and preparation for field activities. Remedial Investigation (RI) Plans were prepared for 10 of the 13 WAGs. These plans were developed with sufficient information to ensure compliance with regulatory requirements, with intensive attention given to environmental, safety, and health protection; waste management; data management; and quality assurance. This paper reports on the progress made during FY 1988 and discusses activities planned for FY 1989

  12. Sealed source and device removal and consolidation feasibility study

    International Nuclear Information System (INIS)

    Ward, J.E.; Carter, J.G.; Meyers, R.L.

    1993-02-01

    The purpose of this study is to assess the feasibility of removing Greater-Than-Class C (GTCC) sealed sources from their containment device and consolidating them for transport to a storage or disposal facility. A sealed source is a sealed capsule containing a radioactive material that is placed in a device providing radioactive containment. It is used in the medical, industrial, research, and food-processing communities for calibrating, measuring, gauging, controlling processes, and testing. This feasibility study addresses the key operational, safety, regulatory, and financial requirements of the removal/consolidation process. This report discusses the process to receive, handle, repackage, and ship these sources to an interim or dedicated storage facility until a final disposal repository can be built and become operational (∼ c. 2010). The study identifies operational and facility requirements to perform this work. Hanford, other DOE facilities, and private hot-cell facilities were evaluated to determine which facilities could perform this work. The personnel needed, design and engineering, facility preparation, process waste disposal requirements, and regulatory compliance were evaluated to determine the cost to perform this work. Cost requirements for items that will have to meet future changing regulatory requirements for transportation, transportation container design and engineering, and disposal were not included in this study. The cost associated with in-process consolidation of the sealed sources reported in this study may have not been modified for inflation and were based on 1992 dollars. This study shows that sealed source consolidation is possible with minimal personnel exposure, and would reduce the risk of radioactive releases to the environment. An initial pilot-scale operation could evaluate the possible methods to reduce the cost and consolidate sources

  13. Feasibility study for a muon detector for the CBM experiment

    International Nuclear Information System (INIS)

    Dutta, Dipanwita; Lebedev, Andrey; Kiseleva, Anna; Ryzhinskiy, Mikhail; Kryshen, Evgeny

    2009-01-01

    The Compressed Baryonic Matter (CBM) experiment at the future FAIR accelerator facility at GSI, Darmstadt is being designed to investigate heavy ion collisions in fixed target mode at beam energies from 10 - 45 A GeV. The major goal is to explore the QCD phase diagram in the region of high baryon densities and at moderate temperatures. One of the proposed key observables is the measurement of charmonium via the dilepton decay channel. As leptons leave the initially produced hot and dense fireball without further interactions, they are excellent probes to study in-medium properties of vector mesons. In this contribution we will present detailed feasibility studies for a di-muon measurement in CBM

  14. Fuel assembly assessment from CVD image analysis: A feasibility study

    International Nuclear Information System (INIS)

    Lindsay, C.S.; Lindblad, T.

    1997-05-01

    The Swedish Nuclear Inspectorate commissioned a feasibility study of automatic assessment of fuel assemblies from images obtained with the digital Cerenkov viewing device currently in development. The goal is to assist the IAEA inspectors in evaluating the fuel since they typically have only a few seconds to inspect an assembly. We report results here in two main areas: Investigation of basic image processing and recognition techniques needed to enhance the images and find the assembly in the image; Study of the properties of the distributions of light from the assemblies to determine whether they provide unique signatures for different burn-up and cooling times for real fuel or indicate presence of non-fuel. 8 refs, 27 figs

  15. Feasibility design study. Land-based OTEC plants. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Brewer, J. H.; Minor, J.; Jacobs, R.

    1979-01-01

    The purpose of this study has been to determine the feasibility of installing 10 MWe (MegaWatt-electric) and 40 MWe land-based OTEC demonstration power plants at two specific sites: Keahole Point on the western shore of the island of Hawaii; and Punta Tuna, on the southeast coast of the main island of Puerto Rico. In addition, the study has included development of design parameters, schedules and budgets for the design, construction and operation of these plants. Seawater systems (intake and discharge pipes) were to be sized so that flow losses were equivalent to those expected with a platform-based OTEC power plant. The power module (components and general arrangement was established based on the TRW design. Results are presented in detail. (WHK)

  16. Autonomous Aerobraking: A Design, Development, and Feasibility Study

    Science.gov (United States)

    Prince, Jill L. H.; Powell, Richard W.; Murri, Dan

    2011-01-01

    Aerobraking has been used four times to decrease the apoapsis of a spacecraft in a captured orbit around a planetary body with a significant atmosphere utilizing atmospheric drag to decelerate the spacecraft. While aerobraking requires minimum fuel, the long time required for aerobraking requires both a large operations staff, and large Deep Space Network resources. A study to automate aerobraking has been sponsored by the NASA Engineering and Safety Center to determine initial feasibility of equipping a spacecraft with the onboard capability for autonomous aerobraking, thus saving millions of dollars incurred by a large aerobraking operations workforce and continuous DSN coverage. This paper describes the need for autonomous aerobraking, the development of the Autonomous Aerobraking Development Software that includes an ephemeris estimator, an atmospheric density estimator, and maneuver calculation, and the plan forward for continuation of this study.

  17. Slaughterhouse sewage treatment using gamma radiation - economical feasibility study

    International Nuclear Information System (INIS)

    Melo, Rita; Botelho, M. Luisa; Branco, Joaquim

    2005-01-01

    This paper presents preliminary results of a financial viability study for the implementation of gamma radiation technology on a slaughterhouse wastewater treatment industry. Five scenarios were studied, including the current practice, representing different types of treatments and goals, e.g.: water reuse and/or sludge add value as agriculture fertilizers. Cost-benefit analysis, including the net present value (NPV) of each scenario, was used as a technique to compare the relative value of various strategies. Taking in account that the initial investment is amortized after 20 years, the implementation of Co-60 treatment with 20% water reuse and sludge application as agriculture fertilizers represents the most profitable project with the highest NPV. Therefore, the implementation of gamma radiation technology on a slaughterhouse wastewater treatment industry is not only technically viable as well as economically feasible. (author)

  18. A feasibility study on nuclear power options in Mongolia

    International Nuclear Information System (INIS)

    Minato, A.; Sekimoto, H.; Amartaivan, T.

    2010-10-01

    There is a growing interest among utilities in the United States in small and medium reactors due primarily to the smaller investment and perhaps shorter construction time involved as compared to those large reactors. The potential market for small reactors (those below 300 M We) exists, specially with sizes of 50 and 100 M We. A feasibility study was conducted on nuclear power options for Ulaanbaatar, Mongolia, a country which has a potential market for small reactors. The study was focused on an optimization of a combination of coal-fired and nuclear power plants taking into account Mongolia's future nuclear program plan, future population and economic growth, and the increased electricity and district heating demands. (Author)

  19. Can microbes compete with cows for sustainable protein production - A feasibility study on high quality protein.

    Science.gov (United States)

    Vestergaard, Mike; Chan, Siu Hung Joshua; Jensen, Peter Ruhdal

    2016-11-08

    An increasing population and their increased demand for high-protein diets will require dramatic changes in the food industry, as limited resources and environmental issues will make animal derived foods and proteins, gradually more unsustainable to produce. To explore alternatives to animal derived proteins, an economic model was built around the genome-scale metabolic network of E. coli to study the feasibility of recombinant protein production as a food source. Using a novel model, we predicted which microbial production strategies are optimal for economic return, by capturing the tradeoff between the market prices of substrates, product output and the efficiency of microbial production. A case study with the food protein, Bovine Alpha Lactalbumin was made to evaluate the upstream economic feasibilities. Simulations with different substrate profiles at maximum productivity were used to explore the feasibility of recombinant Bovine Alpha Lactalbumin production coupled with market prices of utilized materials. We found that recombinant protein production could be a feasible food source and an alternative to traditional sources.

  20. Can microbes compete with cows for sustainable protein production - A feasibility study on high quality protein

    Science.gov (United States)

    Vestergaard, Mike; Chan, Siu Hung Joshua; Jensen, Peter Ruhdal

    2016-11-01

    An increasing population and their increased demand for high-protein diets will require dramatic changes in the food industry, as limited resources and environmental issues will make animal derived foods and proteins, gradually more unsustainable to produce. To explore alternatives to animal derived proteins, an economic model was built around the genome-scale metabolic network of E. coli to study the feasibility of recombinant protein production as a food source. Using a novel model, we predicted which microbial production strategies are optimal for economic return, by capturing the tradeoff between the market prices of substrates, product output and the efficiency of microbial production. A case study with the food protein, Bovine Alpha Lactalbumin was made to evaluate the upstream economic feasibilities. Simulations with different substrate profiles at maximum productivity were used to explore the feasibility of recombinant Bovine Alpha Lactalbumin production coupled with market prices of utilized materials. We found that recombinant protein production could be a feasible food source and an alternative to traditional sources.

  1. [Case and studies].

    Science.gov (United States)

    Schubert, András

    2015-11-15

    Case studies and case reports form an important and ever growing part of scientific and scholarly literature. The paper deals with the share and citation rate of these publication types on different fields of research. In general, evidence seems to support the opinion that an excessive number of such publications may negatively influence the impact factor of the journal. In the literature of scientometrics, case studies (at least the presence of the term "case study" in the titles of the papers) have a moderate share, but their citation rate is practically equal to that of other publication types.

  2. Removable samples for ITER—a feasibility and conceptual study

    International Nuclear Information System (INIS)

    Mertens, Ph; Neubauer, O; Philipps, V; Huber, A; Kirschner, A; Knaup, M; Borodin, D; Samm, U; Ciattaglia, S; Choi, C H; Gicquel, S; Hirai, T; Mitteau, R; Pitts, R A; Sadakov, S; Shimada, M; Veshchev, E

    2014-01-01

    The control of the radioactive inventory in the vacuum vessel of ITER is a main safety issue. Erosion of activated plasma-facing components (PFC) and co-deposition of tritiated dust on PFC and in areas below the divertor constitute the main sources of in-vessel radioactive inventory mobilizable in the case of an accident and also during venting of the vessel. To trace the dust and tritium inventory in the machine, the use of collectors in the form of removable samples was evaluated, beside other techniques, since it provides a reliable way to follow the history of the deposits and check critical areas. Four types of removable probes and two optional active diagnostics were selected out of about 30 different options. For all four probes, a conceptual design was worked out and the feasibility was checked with preliminary estimations of thermal and electromagnetic loads, as well as remote handling paths. The highest temperature estimated for the front face of all probes lies in the range 300–500 °C, which is tolerable. Installed in representative places, such removable samples may provide information about the dust and tritium distribution inside the vacuum vessel. (paper)

  3. Feasibility study for a transportation operations system cask maintenance facility

    Energy Technology Data Exchange (ETDEWEB)

    Rennich, M.J.; Medley, L.G.; Attaway, C.R.

    1991-01-01

    The US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM) is responsible for the development of a waste management program for the disposition of spent nuclear fuel (SNF) and high-level waste (HLW). The program will include a transportation system for moving the nuclear waste from the sources to a geologic repository for permanent disposal. Specially designed casks will be used to safely transport the waste. The cask systems must be operated within limits imposed by DOE, the Nuclear Regulatory Commission (NRC), and the Department of Transportation (DOT). A dedicated facility for inspecting, testing, and maintaining the cask systems was recommended by the General Accounting Office (in 1979) as the best means of assuring their operational effectiveness and safety, as well as regulatory compliance. In November of 1987, OCRWM requested a feasibility study be made of a Cask Maintenance Facility (CMF) that would perform the required functions. 46 refs., 16 figs., 13 tabs.

  4. A feasiblity study of an ultrasonic test phantom arm

    Science.gov (United States)

    Schneider, Philip

    This thesis is a feasibility study for the creation of a test phantom that replicates the physiological features, from an acoustic and mechanical standpoint, of that of a human arm. Physiological feature set includes; Heart, Arteries, Veins, Bone, Muscle, Fat, Skin, and Dermotographic Features (finger prints). Mechanical Aspects include, vascular compression and distention, elasticity of tissue layers, mechanics of human heart. The end goal of which to have a working understanding of each component in order to create a controllable, real time, physiologically accurate, test phantom for a wide range of ultrasonic based applications. These applications can range from devices like wearable technologies to medical training, to biometric "Liveness" detection methods. The proposed phantom would allow for a number of natural bodily functions to be measured including but not limited to vascular mapping, blood pressure, heart rate, subdermal imaging, and general ultrasonic imaging.

  5. Feasibility studies for a wireless 60 GHz tracking detector readout

    CERN Document Server

    Dittmeier, Sebastian; Soltveit, Hans Kristian; Wiedner, Dirk

    2016-01-01

    The amount of data produced by highly granular silicon tracking detectors in high energy physics experiments poses a major challenge to readout systems. At high collision rates, e.g. at LHC experiments, only a small fraction of data can be read out with currently used technologies. To cope with the requirements of future or upgraded experiments new data transfer techniques are required which offer high data rates at low power and low material budget. Wireless technologies operating in the 60 GHz band or at higher frequencies offer high data rates and are thus a promising upcoming alternative to conventional data transmission via electrical cables or optical fibers. Using wireless technology, the amount of cables and connectors in detectors can be significantly reduced. Tracking detectors profit most from a reduced material budget as fewer secondary particle interactions (multiple Coulomb scattering, energy loss, etc.) improve the tracking performance in general. We present feasibility studies regarding the in...

  6. Feasibility Study on Nuclear Propulsion Ship according to Economic Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Gil, Youngmi; Yoo, Seongjin; Oh, June; Byun, Yoonchul; Woo, Ilguk [Daewoo Shipbuilding and Marine Engineering Co., Ltd, Seoul (Korea, Republic of); Kim, Jiho; Choi, Suhn [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-05-15

    The use of nuclear ships has been extending to the icebreaker, the deep-water exploration ship, and the floating nuclear power plant. Prior to developing the new ship, the relevant regulations need to be considered. In this study, we reviewed the nuclear ship-related regulations. In addition, economic value is one of the most important factors which should be considered in the pre-design phase. To evaluate the economics of the nuclear ship, we calculated Capital Expenditure (abbreviated as CAPEX) and Operation Expenditure (abbreviated as OPEX) for various types of ships. We reviewed the nuclear ship-related regulations and evaluated the economics of the nuclear ship compared to the diesel ship. The calculation result shows that economic feasibility of the nuclear ship depends on the oil price as well as the cost of the nuclear reactor.

  7. Cherokee Wind Energy Development - Feasibility and Pre-Construction Studies

    Energy Technology Data Exchange (ETDEWEB)

    McMillan, Andy [Cherokee Nation Businesses, LLC, Catoosa, OK (United States)

    2017-06-30

    Cherokee Nation Businesses (CNB) received a grant from the US Department of Energy to explore feasibility and pursue development of a wind power generation facility on Cherokee land in north-central Oklahoma. This project followed several years of initial study exploring the possibility of commercial-scale wind power generation on primarily agricultural land owned by the Cherokee Nation. This project produced detailed analysis of the legal, financial and market viability of such generation facilities, and encompassed a full technical evaluation of the engineering, environmental, and geotechnical aspects of installing this capacity. During the course of this project, information gleaned from this exploration changed CNB’s thinking about the best course of action for Cherokee participation in the development, eventually moving away from an equity-owner model and towards utilization of the land asset as a resource while mitigating Cherokee financial and operational risk.

  8. Retrospective dosimetry using salted snacks and nuts: a feasibility study

    International Nuclear Information System (INIS)

    Christiansson, M.; Geber-Bergstrand, T.; Bernhardsson, C.; Mattsson, S.; Raeaef, C.L.

    2017-01-01

    The possibility of using ordinary household table salt for dosimetry is suggested by its high sensitivity to ionising radiation, which generates a readout of optically stimulated luminescence (OSL). However, to exploit this finding for retrospective human dosimetry, it would be needed to find salt in close proximity to the exposed individual. Finding salty snacks frequently tucked into handbags, backpacks or pockets seemed to be a possibility; these items therefore became the test materials of the present study. The aluminium or cardboard packages used to exclude the moisture that makes crisps and nuts go soft and stale also helps to retain the induced OSL signal. Therefore, different snacks, either their salt component alone or mixed with the snack, are exposed to ionising radiation and then were assessed for their dosimetric properties. The results indicate the feasibility of using some salty snacks for dosimetry, with a minimum detectable dose as low as 0.2 mGy (authors)

  9. Feasibility study of an active target for the MEG experiment

    Energy Technology Data Exchange (ETDEWEB)

    Papa, A., E-mail: angela.papa@psi.ch [Paul Scherrer Institut PSI, CH-5232 Villigen (Switzerland); Cavoto, G. [INFN Sezione di Roma, P.le Aldo Moro, 2, 00185 Roma (Italy); Ripiccini, E. [INFN Sezione di Roma, P.le Aldo Moro, 2, 00185 Roma (Italy); Dipartimento di Fisica dell' Università degli studi di Roma, P.le Aldo Moro, 2, 00185 Roma (Italy)

    2014-03-01

    We consider the possibility to have an active target for the upgrade of the MEG experiment (MEG II). The active target should work as (1) a beam monitoring, to continuously measure the muon stopping rate and therefore provide a direct evaluation of the detector acceptance (or an absolute normalization of the stopped muon); and as (2) an auxiliary device for the spectrometer, to improve the determination of the muon decay vertex and consequently to achieve a better positron momentum and angular resolutions, detecting the positron from the muon decay. In this work we studied the feasibility of detecting minimum ionizing particle with a single layer of 250 μm fiber and the capability to discriminate between the signal induced by either a muon or a positron.

  10. Feasibility studies of the geochemical Ti-205 solar neutrino experiment

    CERN Document Server

    Neumaier, S; Nolte, E; Morinaga, H

    1991-01-01

    New investigations on the signal to background ratio of the geochemical 205Tl( v., e-)205Pb solar neutrino experiment are presented. The neutrino capture rate of 205Tl and a possible reduction of the neutrino signal due to neutrino oscillations in matter are discussed. The contributions of natural radioactivity, stopped negative muons and fast muons to the background of 205Pb are estimated. The production of radioisotopes in the lead region induced by cosmic ray muons was studied at the high energy muon beam (M2) of CERN with 120, 200 and 280 GeV muons. The background contribution of cosmic ray muons is found to be significantly higher than expected by former estimations and restricts the feasibility of the 205Tl solar neutrino experiment.

  11. Feasibility study of cyclone incineration treatment for radioactive solid waste

    International Nuclear Information System (INIS)

    Zhou Lianquan; Wang Peiyi; Ma Mingxie; Yang Liguo; Li Xiaohai; Qiu Mingcai; Zhang Xiaobin; Dong Jingling; Lu Xiaowu; Li Chuanlian; Yang Baomin

    2002-01-01

    Feasibility study of cyclone incineration treatment for radioactive solid waste is introduced. The structure of cyclone incineration furnace is defined according to test results. The results show: under given conditions of technology: i.e., inlet flowrate ≥30 m/s, total volume ≥210 Nm 3 /h, the mixed solid material with more than 40% of plastics and rubber can completely be incinerated after suitable smash and mixing. The advantages of the furnace are: simple structure, high strength of volume heat, no preheating and combustion-supporting of assistant fuel, bridging and melt leak can be avoided in the stuff. The pretreatment of solid waste is simple, and a little amount of non-combustible substance in the waste can be allowed

  12. Feasibility study of an active target for the MEG experiment

    International Nuclear Information System (INIS)

    Papa, A.; Cavoto, G.; Ripiccini, E.

    2014-01-01

    We consider the possibility to have an active target for the upgrade of the MEG experiment (MEG II). The active target should work as (1) a beam monitoring, to continuously measure the muon stopping rate and therefore provide a direct evaluation of the detector acceptance (or an absolute normalization of the stopped muon); and as (2) an auxiliary device for the spectrometer, to improve the determination of the muon decay vertex and consequently to achieve a better positron momentum and angular resolutions, detecting the positron from the muon decay. In this work we studied the feasibility of detecting minimum ionizing particle with a single layer of 250 μm fiber and the capability to discriminate between the signal induced by either a muon or a positron

  13. Feasibility study for a transportation operations system cask maintenance facility

    International Nuclear Information System (INIS)

    Rennich, M.J.; Medley, L.G.; Attaway, C.R.

    1991-01-01

    The US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM) is responsible for the development of a waste management program for the disposition of spent nuclear fuel (SNF) and high-level waste (HLW). The program will include a transportation system for moving the nuclear waste from the sources to a geologic repository for permanent disposal. Specially designed casks will be used to safely transport the waste. The cask systems must be operated within limits imposed by DOE, the Nuclear Regulatory Commission (NRC), and the Department of Transportation (DOT). A dedicated facility for inspecting, testing, and maintaining the cask systems was recommended by the General Accounting Office (in 1979) as the best means of assuring their operational effectiveness and safety, as well as regulatory compliance. In November of 1987, OCRWM requested a feasibility study be made of a Cask Maintenance Facility (CMF) that would perform the required functions. 46 refs., 16 figs., 13 tabs

  14. A preliminary feasibility study on natural analogue in Korea

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Chun Soo; Bae, Dae Seok; Kim, Kyung Su; Koh, Yong Kwon; Park, Byung Yun

    2000-03-01

    Preliminary study on the assessment of natural analogue study in Korea for the deep geological disposal of high-level radioactive waste was carried out. The project on natural analogue study in other countries are introduced. The uranium-bearing deposit in Okcheon belt are summarized, which reported to be uranium-bearing minerals in order to assess to feasibility for natural analogue study in Korea. Among the uranium-bearing deposits, the Deokpyeong area, reported to be the highest reservoir and grade, are selected as the study site, and the elementary investigation, including survey of radioactivity and geochemistry are carried out. According to the investigation of surface environment, the radioactivity and uranium content in the surface water and shallow groundwater does not show any anormal values. However, the radioactivity is expected to be increased in depth and the groundwater reacted with uranium-bearing graphite formation shows high unanium content, indicating the potential possibility for natural analogue study in Korea. In future, if more detail study are performed, the assessment of natural analogue study in Korea are expected.

  15. Visually guided male urinary catheterization: a feasibility study.

    Science.gov (United States)

    Willette, Paul A; Banks, Kevin; Shaffer, Lynn

    2013-01-01

    Ten percent to 15% of urinary catheterizations involve complications. New techniques to reduce risks and pain are indicated. This study examines the feasibility and safety of male urinary catheterization by nursing personnel using a visually guided device in a clinical setting. The device, a 0.6-mm fiber-optic bundle inside a 14F triple-lumen flexible urinary catheter with a lubricious coating, irrigation port, and angled tip, connects to a camera, allowing real-time viewing of progress on a color monitor. Two emergency nurses were trained to use the device. Male patients 18 years or older presenting to the emergency department with an indication for urinary catheterization using a standard Foley or Coudé catheter were eligible to participate in the study. Exclusion criteria were a current suprapubic tube or gross hematuria prior to the procedure. Twenty-five patients were enrolled. Data collected included success of placement, total procedure time, pre-procedure pain and maximum pain during the procedure, gross hematuria, abnormalities or injuries identified if catheterization failed, occurrence of and reason for equipment failures, and number of passes required for placement. All catheters were successfully placed. The median number of passes required was 1. For all but one patient, procedure time was ≤ 17 minutes. A median increase in pain scores of 1 point from baseline to the maximum was reported. Gross hematuria was observed in 2 patients. The success rate for placement of a Foley catheter with the visually guided device was 100%, indicating its safety, accuracy, and feasibility in a clinical setting. Minimal pain was associated with the procedure. Copyright © 2013 Emergency Nurses Association. Published by Mosby, Inc. All rights reserved.

  16. Feasibility study of plutonium recycling in light water reactors

    International Nuclear Information System (INIS)

    Tabuchi, Hideoto

    1979-01-01

    The feasibility of plutonium recycling in light water reactors has been studied by the Agency of Natural Resources and Energy, MITI. As the first step of the feasibility study, it was planned to charge two fuel assemblies, containing uranium-plutonium mixed oxide (MO 2 ), in the core of the Tsuruga nuclear power plant (BWR) for testing. The design of fuel the safety of these fuel and the operating characteristics of these special fuel assemblies were evaluated. The specifications of MO 2 fuel pin and fuel assembly are compared to those of present uranium oxide (UO 2 ) fuel. The weight of fissile plutonium in one MO 2 fuel assembly is 2.22 kg. The characteristics of MO 2 fuel assemblies, such as reactivity, control rod worth and power distribution can be kept similar to UO 2 fuel. The plutonium isotope ratio of the MO 2 fuel is assumed as that obtained in the fuel taken out of the Tokai No. 1 gas cooled reactor. The temperature distribution in the fuel pellets is shown, compared to that of UO 2 fuel. The linear power density is 440 w/cm at the beginning of the fuel life and 360 w/cm after the burn-up of 44,000 Mwd/t. The stress in the cladding tubes of MO 2 fuel is not different from that of UO 2 fuel. The pellet-cladding interaction (PCM1) was analyzed, utilizing the FEM code, FEAST. Concerning the calculation of resonance absorption, the space dependence of thermal neutron spectra and the nuclear behavior of hollow pellets the methods of design calculation were checked up. It was recognized that regarding the nuclear characteristics of MO 2 fuel, no special technical question remains. (Nakai, Y.)

  17. Feasibility and validity of International Classification of Diseases based case mix indices.

    Science.gov (United States)

    Yang, Che-Ming; Reinke, William

    2006-10-06

    Severity of illness is an omnipresent confounder in health services research. Resource consumption can be applied as a proxy of severity. The most commonly cited hospital resource consumption measure is the case mix index (CMI) and the best-known illustration of the CMI is the Diagnosis Related Group (DRG) CMI used by Medicare in the U.S. For countries that do not have DRG type CMIs, the adjustment for severity has been troublesome for either reimbursement or research purposes. The research objective of this study is to ascertain the construct validity of CMIs derived from International Classification of Diseases (ICD) in comparison with DRG CMI. The study population included 551 acute care hospitals in Taiwan and 2,462,006 inpatient reimbursement claims. The 18th version of GROUPER, the Medicare DRG classification software, was applied to Taiwan's 1998 National Health Insurance (NHI) inpatient claim data to derive the Medicare DRG CMI. The same weighting principles were then applied to determine the ICD principal diagnoses and procedures based costliness and length of stay (LOS) CMIs. Further analyses were conducted based on stratifications according to teaching status, accreditation levels, and ownership categories. The best ICD-based substitute for the DRG costliness CMI (DRGCMI) is the ICD principal diagnosis costliness CMI (ICDCMI-DC) in general and in most categories with Spearman's correlation coefficients ranging from 0.938-0.462. The highest correlation appeared in the non-profit sector. ICD procedure costliness CMI (ICDCMI-PC) outperformed ICDCMI-DC only at the medical center level, which consists of tertiary care hospitals and is more procedure intensive. The results of our study indicate that an ICD-based CMI can quite fairly approximate the DRGCMI, especially ICDCMI-DC. Therefore, substituting ICDs for DRGs in computing the CMI ought to be feasible and valid in countries that have not implemented DRGs.

  18. Feasibility and validity of International Classification of Diseases based case mix indices

    Directory of Open Access Journals (Sweden)

    Reinke William

    2006-10-01

    Full Text Available Abstract Background Severity of illness is an omnipresent confounder in health services research. Resource consumption can be applied as a proxy of severity. The most commonly cited hospital resource consumption measure is the case mix index (CMI and the best-known illustration of the CMI is the Diagnosis Related Group (DRG CMI used by Medicare in the U.S. For countries that do not have DRG type CMIs, the adjustment for severity has been troublesome for either reimbursement or research purposes. The research objective of this study is to ascertain the construct validity of CMIs derived from International Classification of Diseases (ICD in comparison with DRG CMI. Methods The study population included 551 acute care hospitals in Taiwan and 2,462,006 inpatient reimbursement claims. The 18th version of GROUPER, the Medicare DRG classification software, was applied to Taiwan's 1998 National Health Insurance (NHI inpatient claim data to derive the Medicare DRG CMI. The same weighting principles were then applied to determine the ICD principal diagnoses and procedures based costliness and length of stay (LOS CMIs. Further analyses were conducted based on stratifications according to teaching status, accreditation levels, and ownership categories. Results The best ICD-based substitute for the DRG costliness CMI (DRGCMI is the ICD principal diagnosis costliness CMI (ICDCMI-DC in general and in most categories with Spearman's correlation coefficients ranging from 0.938-0.462. The highest correlation appeared in the non-profit sector. ICD procedure costliness CMI (ICDCMI-PC outperformed ICDCMI-DC only at the medical center level, which consists of tertiary care hospitals and is more procedure intensive. Conclusion The results of our study indicate that an ICD-based CMI can quite fairly approximate the DRGCMI, especially ICDCMI-DC. Therefore, substituting ICDs for DRGs in computing the CMI ought to be feasible and valid in countries that have not

  19. Community pharmacy-based case finding for COPD in urban and rural settings is feasible and effective.

    Science.gov (United States)

    Fathima, Mariam; Saini, Bandana; Foster, Juliet M; Armour, Carol L

    2017-01-01

    Case finding of patients at risk of COPD by community pharmacists could identify a substantial number of people with undiagnosed COPD, but little is known about the feasibility and effectiveness of pharmacy-based COPD case finding using microspirometry. The objective of this study was to assess the feasibility and effectiveness of COPD case-finding service provided by community pharmacists, utilizing a combination of risk assessment questionnaire and microspirometry. A 6-month service was conducted in 21 community pharmacies in Australia. Pharmacists trained in COPD case finding, including lung function test (LFT), invited their patients aged ≥35 years with a history of smoking and/or respiratory symptoms to participate. High-risk patients were identified via a COPD risk assessment questionnaire (Initial Screening Questionnaire [ISQ]) and underwent LFT. Pharmacists referred patients with a forced expiratory volume in 1 second (FEV 1 )/forced expiratory volume in 6 seconds (FEV 6 ) ratio 3 indicating high COPD risk. Of the 157 patients who were able to complete LFT, 61 (39%) had an FEV 1 /FEV 6 ratio of 3) were at a significantly higher risk of an FEV 1 /FEV 6 ratio of strategy for reducing the burden of COPD, particularly for those living in rural locations.

  20. Feasibility Study on Solar District Heating in China

    DEFF Research Database (Denmark)

    Huang, Junpeng; Fan, Jianhua; Furbo, Simon

    This paper analyzes the feasibility of developing solar district heating (SDH) in China from the perspective of incentive policy, selections of technical route, regional adaptability and economic feasibility for clean heating. Based on the analyzation, this proposes a road map for the development...

  1. Feasibility study on a cosmic-ray level gauge

    International Nuclear Information System (INIS)

    Matsuda, H.; Fukaya, M.; Minato, S.

    1989-01-01

    Cosmic-ray intensities were measured at the stairs in a subway station in Nagoya City, inside a tall concrete building and under a cylindrical water tank, to examine the feasibility of a cosmic-ray level gauge. The measured results agreed quite well with the theoretical calculations. These results show that a cosmic-ray level gauge is feasible. (author)

  2. Feasibility study of gamma-ray medical radiography

    International Nuclear Information System (INIS)

    Alyassin, Abdalmajeid M.; Maqsoud, Hamza A.; Mashat, Ahmad M.; Al-Mohr, Al-Sayed; Abdulwajid, Subhan

    2013-01-01

    This research explores the feasibility of using gamma-ray radiography in medical imaging. We will show that gamma-ray medical radiography has the potential to provide alternative diagnostic medical information to X-ray radiography. Approximately one Ci Am-241 radioactive source which emits mono-energetic 59.5 keV gamma rays was used. Several factors that influence the feasibility of this study were tested. They were the radiation source uniformity, image uniformity, and image quality parameters such as contrast, noise, and spatial resolution. In addition, several gamma-ray and X-ray images were acquired using humanoid phantoms. These images were recorded on computed radiography image receptors and displayed on a standard monitor. Visual assessments of these images were then conducted. The Am-241 radioactive source provided relatively uniform radiation exposure and images. Image noise and image contrast were mainly dependent on the exposure time and source size, whereas spatial resolution was dependent on source size and magnification factor. The gamma-ray humanoid phantom images were of lower quality than the X-ray images mainly due to the low radioactivity used and not enough exposure time. Nevertheless, the gamma-ray images displayed most of the main structures contained in the humanoid phantoms. Higher exposure rates and thus lower exposure times were estimated for different pure Am-241 source sizes that are hypothesized to provide high quality images similar to X-ray images. For instance, a 10 mm source size of pure Am-241 with 7 s exposure time should produce images similar in contrast and noise to X-ray images. This research paves the way for the production and usage of a highly radioactive Am-241 source with the potential to lead to the feasibility of acceptable quality medical gamma-ray radiography. - Highlights: ► Characterized the performance of gamma-ray radiography. ► Displayed medical images of humanoid phantoms using gamma radiography. ► Am-241

  3. Can microbes compete with cows for sustainable protein production - A feasibility study on high quality protein

    DEFF Research Database (Denmark)

    Vestergaard, Mike; Chan, Siu Hung Joshua; Jensen, Peter Ruhdal

    2016-01-01

    An increasing population and their increased demand for high-protein diets will require dramatic changes in the food industry, as limited resources and environmental issues will make animal derived foods and proteins, gradually more unsustainable to produce. To explore alternatives to animal...... derived proteins, an economic model was built around the genome-scale metabolic network of E. coli to study the feasibility of recombinant protein production as a food source. Using a novel model, we predicted which microbial production strategies are optimal for economic return, by capturing the tradeoff...... between the market prices of substrates, product output and the efficiency of microbial production. A case study with the food protein, Bovine Alpha Lactalbumin was made to evaluate the upstream economic feasibilities. Simulations with different substrate profiles at maximum productivity were used...

  4. Intraarterial Ultrasound in Pancreatic Cancer: Feasibility Study and Preliminary Results

    International Nuclear Information System (INIS)

    Larena-Avellaneda, Axel; Timm, Stephan; Kickuth, Ralph; Kenn, Werner; Steger, Ulrich; Jurowich, Christian; Germer, Christoph-Thomas

    2010-01-01

    Despite technological advances in computed tomography (CT) and magnetic resonance imaging, the involvement of the celiac or mesenteric artery in pancreatic cancer remains uncertain in many cases. Infiltration of these vessels is important in making decisions about therapy choices but often can only be definitively determined through laparotomy. Local (intraarterial) ultrasound may increase diagnostic accuracy. Using the Volcano intravascular ultrasound (IVUS) system, we applied a transfemoral method to scan the celiac and mesenteric arteries directly intraarterial. This technique was used in five patients with suspected pancreatic cancer. Technical success was achieved in all cases. In one case, a short dissection of the mesenteric artery occurred but could be managed interventionally. In tumors that did not contact with the vessels, IVUS was unable to display the tissue pathology. Our main interest was the infiltration of the arteries. In one case, infiltration was certain in the CT scan but uncertain in two patients. In the latter two cases, IVUS correctly predicted infiltration in one and freedom from tumor in the other case. In our preliminary study, IVUS correctly predicted arterial infiltration in all cases. IVUS did not provide new information when the tumor was far away from the vessel. Compared with IVUS in the portal vein, the information about the artery is more detailed, and the vessel approach is easier. These results encouraged us to design a prospective study to evaluate the sensitivity and specificity of this method.

  5. How to Train an Injured Brain? A Pilot Feasibility Study of Home-Based Computerized Cognitive Training.

    Science.gov (United States)

    Verhelst, Helena; Vander Linden, Catharine; Vingerhoets, Guy; Caeyenberghs, Karen

    2017-02-01

    Computerized cognitive training programs have previously shown to be effective in improving cognitive abilities in patients suffering from traumatic brain injury (TBI). These studies often focused on a single cognitive function or required expensive hardware, making it difficult to be used in a home-based environment. This pilot feasibility study aimed to evaluate the feasibility of a newly developed, home-based, computerized cognitive training program for adolescents who suffered from TBI. Additionally, feasibility of study design, procedures, and measurements were examined. Case series, longitudinal, pilot, feasibility intervention study with one baseline and two follow-up assessments. Nine feasibility outcome measures and criteria for success were defined, including accessibility, training motivation/user experience, technical smoothness, training compliance, participation willingness, participation rates, loss to follow-up, assessment timescale, and assessment procedures. Five adolescent patients (four boys, mean age = 16 years 7 months, standard deviation = 9 months) with moderate to severe TBI in the chronic stage were recruited and received 8 weeks of cognitive training with BrainGames. Effect sizes (Cohen's d) were calculated to determine possible training-related effects. The new cognitive training intervention, BrainGames, and study design and procedures proved to be feasible; all nine feasibility outcome criteria were met during this pilot feasibility study. Estimates of effect sizes showed small to very large effects on cognitive measures and questionnaires, which were retained after 6 months. Our pilot study shows that a longitudinal intervention study comprising our novel, computerized cognitive training program and two follow-up assessments is feasible in adolescents suffering from TBI in the chronic stage. Future studies with larger sample sizes will evaluate training-related effects on cognitive functions and underlying brain structures.

  6. Feasibility Study and Demonstration of an Aluminum and Ice Solid Propellant

    Directory of Open Access Journals (Sweden)

    Timothee L. Pourpoint

    2012-01-01

    Full Text Available Aluminum-water reactions have been proposed and studied for several decades for underwater propulsion systems and applications requiring hydrogen generation. Aluminum and water have also been proposed as a frozen propellant, and there have been proposals for other refrigerated propellants that could be mixed, frozen in situ, and used as solid propellants. However, little work has been done to determine the feasibility of these concepts. With the recent availability of nanoscale aluminum, a simple binary formulation with water is now feasible. Nanosized aluminum has a lower ignition temperature than micron-sized aluminum particles, partly due to its high surface area, and burning times are much faster than micron aluminum. Frozen nanoscale aluminum and water mixtures are stable, as well as insensitive to electrostatic discharge, impact, and shock. Here we report a study of the feasibility of an nAl-ice propellant in small-scale rocket experiments. The focus here is not to develop an optimized propellant; however improved formulations are possible. Several static motor experiments have been conducted, including using a flight-weight casing. The flight weight casing was used in the first sounding rocket test of an aluminum-ice propellant, establishing a proof of concept for simple propellant mixtures making use of nanoscale particles.

  7. Dynamic electron arc radiotherapy (DEAR): a feasibility study

    International Nuclear Information System (INIS)

    Rodrigues, Anna; Yin, Fang-Fang; Wu, Qiuwen

    2014-01-01

    Compared to other radiation therapy modalities, clinical electron beam therapy has remained practically unchanged for the past few decades even though electron beams with multiple energies are widely available on most linacs. In this paper, we present the concept of dynamic electron arc radiotherapy (DEAR), a new conformal electron therapy technique with synchronized couch motion. DEAR utilizes combination of gantry rotation, couch motion, and dose rate modulation to achieve desirable dose distributions in patient. The electron applicator is kept to minimize scatter and maintain narrow penumbra. The couch motion is synchronized with the gantry rotation to avoid collision between patient and the electron cone. In this study, we investigate the feasibility of DEAR delivery and demonstrate the potential of DEAR to improve dose distributions on simple cylindrical phantoms. DEAR was delivered on Varian's TrueBeam linac in Research Mode. In conjunction with the recorded trajectory log files, mechanical motion accuracies and dose rate modulation precision were analyzed. Experimental and calculated dose distributions were investigated for different energies (6 and 9 MeV) and cut-out sizes (1×10 cm 2  and 3×10 cm 2  for a 15×15 cm 2  applicator). Our findings show that DEAR delivery is feasible and has the potential to deliver radiation dose with high accuracy (root mean square error, or RMSE of <0.1 MU, <0.1° gantry, and <0.1 cm couch positions) and good dose rate precision (1.6 MU min −1 ). Dose homogeneity within ±2% in large and curved targets can be achieved while maintaining penumbra comparable to a standard electron beam on a flat surface. Further, DEAR does not require fabrication of patient-specific shields. These benefits make DEAR a promising technique for conformal radiotherapy of superficial tumors. (paper)

  8. Feasibility study on the least square method for fitting non-Gaussian noise data

    Science.gov (United States)

    Xu, Wei; Chen, Wen; Liang, Yingjie

    2018-02-01

    This study is to investigate the feasibility of least square method in fitting non-Gaussian noise data. We add different levels of the two typical non-Gaussian noises, Lévy and stretched Gaussian noises, to exact value of the selected functions including linear equations, polynomial and exponential equations, and the maximum absolute and the mean square errors are calculated for the different cases. Lévy and stretched Gaussian distributions have many applications in fractional and fractal calculus. It is observed that the non-Gaussian noises are less accurately fitted than the Gaussian noise, but the stretched Gaussian cases appear to perform better than the Lévy noise cases. It is stressed that the least-squares method is inapplicable to the non-Gaussian noise cases when the noise level is larger than 5%.

  9. A study of critical paths for feasibility studies of mining projects

    International Nuclear Information System (INIS)

    Sayadi, R.

    2002-01-01

    This work develops a model for design and realisation of profitability's and feasibility studies of a mining project. The model provides the structure of various necessary procedures to establish the feasibility studies and presents a logical system of task sequencing and information circulating between tasks. The specifications of mining projects, particularly their duration, complexity and high costs, necessitate design and realisation of feasibility study bases on the sufficient understanding of task behaviour and the critical path method view. For this purpose, critical paths with the highest frequency of occurrence were studied through several simulations. In addition, the critical tasks and sub tasks with the most probability were identified. The model introduced in this paper can serve as a perfect tool in feasibility study of a mining project. It can also be used as a basis of future development of mining software

  10. Feasibility study for an asymmetric B-factory at KEK

    International Nuclear Information System (INIS)

    Ozaki, Hitoshi; Yoshimura, Yoshio

    1990-06-01

    In June, 1989, the study group for exploring the feasibility of B meson physics using an asymmetric energy accelerator was organized. This report is the summary of the results of the works that this study group carried out in nine months, and is the Japanese edition of the report of English edition 'Task Force Report on Asymmetric B-factory at KEK'. The activity plan of the study group was to make up the plan exceeding the preceding CLEO-2 experiment by utilizing the features of an asymmetric B-factory. Under this plan, the activities have been carried out by the study meetings twice every week on the physics side and once every two weeks on the accelerator side. Besides, in two study meetings held in October and December, 1989, several persons who have engaged in the research on B meson physics actually in foreign countries were invited, and the discussion was carried out. At present toward the materialization of the plan, the concrete investigation of accelerators and measuring instruments was begun. The significance of a B-factory and the construction project, the physics of a B-factory, the experimental method and the plan for an accelerator are reported. (K.I.)

  11. Feasibility of exercising adults with asthma: a randomized pilot study

    Directory of Open Access Journals (Sweden)

    Boyd Amy

    2012-08-01

    Full Text Available Abstract Background Aerobic exercise appears to have clinical benefits for many asthmatics, yet a complete understanding of the mechanisms underlying these benefits has not been elucidated at this time. Purpose The objective of this study was to determine feasibility for a larger, future study that will define the effect of aerobic exercise on cellular, molecular, and functional measures in adults with mild-moderate asthma. Design Recruited subjects were randomized into usual care (sedentary or usual care with moderate intensity aerobic exercise treatment groups. Setting / Participants Nineteen adults with mild-moderate asthma but without a recent history of exercise were recruited at the UAB Lung Health Center, Birmingham, AL. Intervention The exercise group underwent a 12 week walking program exercising at 60 – 75% of maximum heart rate (HRmax. Subjects self-monitored HRmax levels using heart rate monitors; exercise diaries and recreation center sign-in logs were also used. Main outcome measures Functional measures, including lung function and asthma control scores, were evaluated for all subjects at pre- and post-study time-points; fitness measures were also assessed for subjects in the exercise group. Peripheral blood and nasal lavage fluid were collected from all subjects at pre- and post-study visits in order to evaluate cellular and molecular measures, including cell differentials and eosinophilic cationic protein (ECP. Results Sixteen subjects completed the prescribed protocol. Results show that subjects randomized to the exercise group adhered well (80% to the exercise prescription and exhibited a trend toward improved fitness levels upon study completion. Both groups exhibited improvements in ACQ scores. No changes were observed in lung function (FEV1, FEV1/FVC, cell differentials, or ECP between groups. Conclusions Results indicate that a moderate intensity aerobic exercise training program may improve asthma control and fitness

  12. IRT - Sofia conversion feasibility study experience 2002-2009

    Energy Technology Data Exchange (ETDEWEB)

    Belousov, S.I.; Apostolov, T.G. [Institute for Nuclear Research and Nuclear Energy of Bulgarian Academy of Science, Tsarigradsko 72, 1784 Sofia (Bulgaria)

    2010-07-01

    A joint conversion feasibility study concerning the IRT - Sofia research reactor between INRNE and the RERTR Program at ANL was initiated in 2002. The initial steps studies (up to 2006) were mainly focused on neutronics properties significant for reactor application and safety analyses. Thermal hydraulic, accident analyses as well as additional neutronics study required were performed after that (up to 2010). The obtained results show that the IRT-4M LEU fuel assemblies (19.75% {sup 235}U enrichment) are appropriate for IRT-Sofia conversion (IRT-Sofia was initially designed for the IRT-2M HEU fuel assemblies with 36% {sup 235}U enrichment). The results obtained in the frames of the joint study show that the IRT-Sofia operation even with usage of only one pump in the primary circuit meets all safety requirements at power level up to 1000 kW and that safety is maintained for accident transients. Presented results of analyses (neutronics, thermal hydraulic, and accident) and accumulated experience for the IRT-Sofia will be useful for other research reactors where conversion from IRT-2M (HEU) to IRT-4M (LEU) fuel is underway and/or foreseen. (authors)

  13. Steps for preparing uranium production feasibility studies: A guidebook

    International Nuclear Information System (INIS)

    1996-06-01

    Uranium exploration, development and eventual production, form a series of progressive and logical steps. Each step is part of a progression of activities with the objective of obtaining new or additional information from which a crucial decision is to be made. This guidebook is primarily aimed at mineral management personnel in developing countries who have little or no experience in preparing feasibility studies in uranium production. It is not a textbook which describes the geology, mining or processing of uranium. This guidebook deals with the philosophy, basic principles and important factors in the various stages of economic evaluation of the project. This guidebook is primarily concerned with small to medium sized mining projects. However, it can also provide useful guidance for the initial study of larger mining projects. More detailed studies of larger projects, however, should be left to well known experts in the field. While the mineral commodity in question is uranium, the procedures and approaches outlined in this guidebook are generally applicable to the study of other commodities. Refs, figs, tabs

  14. Feasibility study on the development of advanced LWR fuel technology

    International Nuclear Information System (INIS)

    Jung, Youn Ho; Sohn, D. S.; Jeong, Y. H.; Song, K. W.; Song, K. N.; Chun, T. H.; Bang, J. G.; Bae, K. K.; Kim, D. H. and others.

    1997-07-01

    Worldwide R and D trends related to core technology of LWR fuels and status of patents have been surveyed for the feasibility study. In addition, various fuel cycle schemes have been studied to establish the target performance parameters. For the development of cladding material, establishment of long-term research plan for alloy development and optimization of melting process and manufacturing technology were conducted. A work which could characterize the effect of sintering additives on the microstructure of UO 2 pellet has been experimentally undertaken, and major sintering variables and their ranges have been found in the sintering process of UO 2 -Gd 2 O 3 burnable absorber pellet. The analysis of state of the art technology related to flow mixing device for spacer grid and debris filtering device for bottom nozzle and the investigation of the physical phenomena related to CHF enhancement and the establishment of the data base for thermal-hydraulic performance tests has been done in this study. In addition, survey on the documents of the up-to-date PWR fuel assemblies developed by foreign vendors have been carried out to understand their R and D trends and establish the direction of R and D for these structural components. And, to set the performance target of the new fuel, to be developed, fuel burnup and economy under the extended fuel cycle length scheme were estimated. A preliminary study on the failure mechanism of CANDU fuel, key technology and advanced coating has been performed. (author). 190 refs., 31 tabs., 129 figs

  15. Feasibility study of application of ductless fuel assembly to FBR

    International Nuclear Information System (INIS)

    Itoh, K.; Shibahara, I.

    1996-01-01

    Feasibility studies on an application of the ductless fuel concept to an FBR core have been carried out in order to evaluate the basic features of the ductless core, especially in the fields of the thermal-hydraulic aspects and the mechanical behaviors. Regarding thermal-hydraulic aspects, analyses were performed by using a whole core thermal-hydraulic analysis code by making some modification for this study on the PWR code THINC. A small scaled ductless core model was prepared and a hydraulic experiment was carried out to study basic hydraulic characteristics of a ductless core. Core mechanical behaviors were analyzed focusing on the core irradiation bowing aspects and the seismic behaviors. Following features are revealed on the core structural behaviors: (1) the bowing stiffness of the ductless assembly is around 1/5 to 1/10 of that of the duct type assembly; (2) the contact loads between assemblies by the bowing effects are small through core cycles; (3) the damping of the ductless assemblies are so large that the seismic responses are small and the loads between assemblies are small due to occurring many contact points. Through this study it is expected that the concept of the ductless fuel can be applicable to FBR cores from the design view points of thermal-hydraulic and core mechanical behaviors

  16. Haggart Island dams : reconstruction/rehabilitation feasibility study : final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-03-15

    This feasibility study was conducted to identify and evaluate the range of options available for the repair or reconstruction of the Haggart Island Dams, and to provide the required information needed to decide upon the preferred solution and secure funding for the final design for reconstruction. In addition, the study presented the initial stages needed to satisfy the environmental assessment process regarding the selection of options related to the structures. Information relating to: fish habitat; flood mapping; historical flow data; condition of the dams; historical significance of the dams and their relation to the area; recreational opportunities for the area and previous public consultation records was presented. Issues regarding water level were addressed through a hydraulic analysis. Field and background data were compiled in order to establish the existing conditions of the study area. Background information regarding the natural features of the study area was presented. Safety issues were assessed in developing landscaping features and pathway planning. Details of public consultation procedures were presented. Information from stakeholders was gathered regarding recreational activities, river flow, historical and nature related issues to develop an understanding of the significance of the dams. Various design alternatives were presented, as well as details of the current, deteriorating state of the dams. 5 tabs., 24 figs.

  17. Feasibility Study of a Lunar Analog Bed Rest Model

    Science.gov (United States)

    Cromwell, Ronita L.; Platts, Steven H.; Yarbough, Patrice; Buccello-Stout, Regina

    2010-01-01

    The purpose of this study was to determine the feasibility of using a 9.5deg head-up tilt bed rest model to simulate the effects of the 1/6 g load to the human body that exists on the lunar surface. The lunar analog bed rest model utilized a modified hospital bed. The modifications included mounting the mattress on a sled that rolled on bearings to provide freedom of movement. The weight of the sled was off-loaded using a counterweight system to insure that 1/6 body weight was applied along the long axis (z-axis) of the body. Force was verified through use of a force plate mounted at the foot of the bed. A seating assembly was added to the bed to permit periods of sitting. Subjects alternated between standing and sitting positions throughout the day. A total of 35% of the day was spent in the standing position and 65% was spent sitting. In an effort to achieve physiologic fluid shifts expected for a 1/6 G environment, subjects wore compression stockings and performed unloaded foot and ankle exercises. Eight subjects (3 females and 5 males) participated in this study. Subjects spent 13 days in the pre-bed rest phase, 6 days in bed rest and 3 days post bed rest. Subjects consumed a standardized diet throughout the study. To determine feasibility, measures of subject comfort, force and plasma volume were collected. Subject comfort was assessed using a Likert scale. Subjects were asked to assess level of comfort (0-100) for 11 body regions and provide an overall rating. Results indicated minimal to no discomfort as most subjects reported scores of zero. Force measures were performed for each standing position and were validated against subject s calculated 1/6 body weight (r(sup 2) = 0.993). The carbon monoxide rebreathing technique was used to assess plasma volume during pre-bed rest and on the last day of bed rest. Plasma volume results indicated a significant decrease (p = 0.001) from pre to post bed rest values. Subjects lost on average 8.3% (sd = 6.1%) during the

  18. Feasibility study for a computerized emergency preparedness simulation facility

    International Nuclear Information System (INIS)

    Gerhardstein, L.H.; Schroeder, J.O.; Sandusky, W.F.

    1979-11-01

    This report details the feasibility of a computerized Emergency Preparedness Simulation Facility (EPSF) for use by the Nuclear Regulatory Commission (NRC). The proposed facility would be designed to provide the NRC and other federal, state, and local government agencies with a capability to formulate, test, and evaluate the Emergency Preparedness Plans (EPP) which local and state agencies have/will establish for use during nuclear emergencies. In cases of any state emergency (including a nuclear emergency), high level state government officials will direct emergency procedures and insure that state and local emergency teams carry out tasks which have been established in their EPP. When an emergency exists, rapid mobilization of emergency teams, efficient communication, and effective coordination of individual team efforts is essential to safety, preservation of property, and overall public welfare. Current EPP evaluation procedures are qualitative in nature and while they do compare emergency drill performance with the EPP, the nature of the drills often does not provide enough realism to actual emergency conditions. Automated simulation of real emergency conditions using modern computer equipment and programming techniques will provide the NRC emergency evaluation teams a simulated environment which closely approximates conditions which would actually exist during a real emergency. In addition, the computer can be used to collect and log performance and event data which will aid the evaluation team in making assessments of the state or local area's EPP and their Emergency Preparedness Teams performance during emergency drills. Overall, a computerized EPSF can improve drill testing and evaluation efficiency, provide approximate emergency condition realism, and improve public awareness of local emergency procedures

  19. Cone-beam volume CT mammographic imaging: feasibility study

    Science.gov (United States)

    Chen, Biao; Ning, Ruola

    2001-06-01

    X-ray projection mammography, using a film/screen combination or digital techniques, has proven to be the most effective imaging modality for early detection of breast cancer currently available. However, the inherent superimposition of structures makes small carcinoma (a few millimeters in size) difficult to detect in the occultation case or in dense breasts, resulting in a high false positive biopsy rate. The cone-beam x-ray projection based volume imaging using flat panel detectors (FPDs) makes it possible to obtain three-dimensional breast images. This may benefit diagnosis of the structure and pattern of the lesion while eliminating hard compression of the breast. This paper presents a novel cone-beam volume CT mammographic imaging protocol based on the above techniques. Through computer simulation, the key issues of the system and imaging techniques, including the x-ray imaging geometry and corresponding reconstruction algorithms, x-ray characteristics of breast tissues, x-ray setting techniques, the absorbed dose estimation and the quantitative effect of x-ray scattering on image quality, are addressed. The preliminary simulation results support the proposed cone-beam volume CT mammographic imaging modality in respect to feasibility and practicability for mammography. The absorbed dose level is comparable to that of current two-view mammography and would not be a prominent problem for this imaging protocol. Compared to traditional mammography, the proposed imaging protocol with isotropic spatial resolution will potentially provide significantly better low contrast detectability of breast tumors and more accurate location of breast lesions.

  20. Feasibility study of energy conservation at Vietnam Steel Corporation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Feasibility study was conducted of the project for energy conservation and reduction in greenhouse effect gas emission by introducing the honeycomb type heat storage burner technology to heating furnaces of Vietnam Steel Corporation (VSC). Furnaces for study are the bar mill furnace at Gia Sang plant of TISCO Steelorks, bar mill furnace at Thu Duc plant of SSC Steelworks, billet furnace at new bar mill of SSC Steelworks, slab furnace at new hot strip mill that VSC is now in the planning stage. As a result of the study, the energy conservation amount is 2,900 toe/y at TISCO Steelworks, 2,130 toe/y at SSC Steelworks, and 6,000 toe/y at VSC new hot strip mill, which totaled 11,030 toe/y. The amount of greenhouse effect gas reduction is 9,000 t-CO2/y at TISCO, 6,600 t-CO2/y at SSC, and 18,600 t-CO2/y at VSC, which totaled 34,200 t/y. The total investment amount is 0.23, 0.44, 1.32 and 1.99 billion yen for each. As to the profitability, the internal earning rate is 24%, 86%, 97% and 51% for each, which are all favorable. (NEDO)

  1. Smoking cessation research via the internet: a feasibility study.

    Science.gov (United States)

    Stoddard, Jacqueline; Delucchi, Kevin; Muñoz, Ricardo; Collins, Noah; Stable, Eliseo Pérez; Augustson, Erik; Lenert, Leslie

    2005-01-01

    To reverse the present stagnation in progress toward reduced smoking rates, new widely accessible treatment methods for smoking cessation must be developed and evaluated with large groups of smokers. We tested the feasibility of conducting a smoking cessation study over the Internet using a brief, self-help educational intervention. Through a direct e-mail sent from a large health information web site (WebMD), and with our presence on the Internet, we recruited 538 adult smokers to the study. Most participants (90.5%) completed all baseline questionnaires. Questionnaires showed acceptable to good reliability and were comparable with studies using paper-and-pencil methods. Participants appeared to be highly dependent on nicotine. Forty-two percent indicated being ready to quit smoking at baseline. At 1-month follow-up, 42.8% of baseline participants returned a complete follow-up questionnaire, 40% of whom indicated having made a serious quit attempt, and 8.3% of whom indicated 7-day abstinence. Most follow-up participants rated the site as at least somewhat helpful to quitting (74.9%) and reported at least a slight increased intention to quit smoking over baseline (67.3%). While Internet-enabled self-help interventions for smoking cessation are able to reach large numbers of smokers interested in quitting smoking, additional procedures are needed to retain these users for treatment and follow-up assessments.

  2. Zirconia based inert matrix fuel: fabrication concepts and feasibility studies

    International Nuclear Information System (INIS)

    Ingold, F.; Burghartz, M.; Ledergerber, G.

    1999-01-01

    The internal gelation process has traditionally been applied to fabricate standard fuel based on uranium, typically UO2 and MOX. To meet the recent aim to destroy plutonium in the most effective way, a uranium free fuel was evaluated. The fuel development programme at PSI has been redirected toward a fuel based on zirconium oxide or a mixture of zirconia and a conducting material to form ceramic/metal (CERMET) or ceramic/ceramic (CERCER) combinations. A feasibility study was carried out to demonstrate that microspheres based on zirconia and spinel can be fabricated with the required properties. The gelation parameters were investigated to optimise compositions of the starting solutions. Studies to fabricate a composite material (from zirconia and spinel) are ongoing. If the zirconia/spinel ratio is chosen appropriately, the low thermal conductivity of pure zirconia can be compensated by the higher thermal conductivity of spinel. Another solution to offset the low thermal conductivity of zirconia is the development of a CERMET, which consists of fine particles bearing plutonium in a cubic zirconia lattice dispersed in a metallic matrix. The fabrication of such a CERMET is also being studied. (author)

  3. Feasibility study of a portable smelter for scrap metals

    International Nuclear Information System (INIS)

    Cavendish, J.H.

    1976-06-01

    The use of a portable smelter to process uranium-contaminated scrap metals was studied. Objectives were to convert scrap metal located at many diverse sites into a form which would be suitable for unlicensed sale and reduce the problems associated with storing the scrap. The Foundry Design Company study indicated the portable smelter concept was feasible from an equipment and transportation standpoint. Capital costs for a 5-ton/hour (steel) nominal capacity unit were estimated to be $2,349,000. Technical evaluation indicates that all the common metals considered, i.e., iron, nickel, copper, and aluminum, are amenable to uranium decontamination by smelting except aluminum. An economic evaluation of the processing of the 30,000 tons of steel scrap to be generated by the Cascade Improvement Program by a portable smelter was made based upon information supplied by Foundry Design Company, plus the assumption that the product metal could be sold for $120.00 per ton. This evaluation indicated a net return of $2,424,000 to the government could be realized. The Health and Safety study indicated no major problems of this nature would be encountered in operating a portable smelter. The legal review indicated the proposed operation fell within the authority of existing regulations. Consideration of possible conflicts with regard to competition with the private sector was suggested

  4. Feasibility study for PTV measurement using x-ray holography

    International Nuclear Information System (INIS)

    Uemura, Tomomasa; Yamamoto, Yasufumi; Murata, Shigeru; Nishio, Shigeru; Iguchi, Manabu; Uesugi, Kentaro

    2005-01-01

    Some X-ray imaging techniques are examined for a feasibility study for micro-PIV in this study. There are three X-ray imaging method, the absorption contrast method, the refraction contrast method, and the phase contrast method. The first one is a common method but its spatial resolution is rather poor. The 2nd method corresponds to the Schlieren method that utilizes refraction of parallel light. The characteristics of the method, edge enhancement, can be effective in extracting tracer images. The third method is a kind of holography methods, and this method can record fine tracer particles. Among the three methods, the second and the third method are seemed to be applicable to PIV imaging, and those methods need a parallel X-ray. The SPring-8, the synchrotron radiation facility in Harima, is utilized. There are some methods to realize phase contrast image, most of them requires ultra-high precision in optical alignment. In the present study, though a coherent source is indispensable, the simplest and robust holography method, the inline holography, is used to take phase contrast pictures. (author)

  5. Septic Systems Case Studies

    Science.gov (United States)

    A collection of septic systems case studies to help community planners, elected officials, health department staff, state officials, and interested citizens explore alternatives for managing their decentralized wastewater treatment systems.

  6. HYDROGEOLOGIC CASE STUDIES

    Science.gov (United States)

    Hydrogeology is the foundation of subsurface site characterization for evaluations of monitored natural attenuation (MNA). Three case studies are presented. Examples of the potentially detrimental effects of drilling additives on ground-water samples from monitoring wells are d...

  7. A Psychobiographical Case Study

    African Journals Online (AJOL)

    man, and cancer fighter. This psychobiographical case study entailed a psychosocial-historical ... does not draw more attention as a research method, as this approach has .... of the applied Levinsonian theory to the life of Jobs against the ...

  8. Quantification of manganese in human hand bones: a feasibility study

    International Nuclear Information System (INIS)

    Aslam; Pejovic-Milic, A; Chettle, D R; McNeill, F E

    2008-01-01

    Manganese is both an essential element to human health and also toxic when humans are exposed to excessive levels, particularly by means of inhalation. Biological monitoring of manganese exposure is problematic. It is subject to homeostasis; levels in blood (or serum/plasma) reflect only the most recent exposure and rapidly return to within normal ranges, even when there has been a temporary excursion in response to exposure. In this context, we have been developing a non-invasive technique for measurement of manganese stored in bone, using in vivo neutron activation analysis. Following preliminary feasibility studies, the technique has been enhanced by two significant infrastructure advances. A specially designed irradiation facility serves to maximize the activation of manganese with respect to the dose of ionizing radiation. Secondly, an array of eight NaI(Tl) crystals provides a detection system with very close to 4π geometry. This feasibility study, using neutron activation analysis to measure manganese in the bones of the hand, takes two features into account. Firstly, there is considerable magnesium present in the bone and this produces a spectral interference with the manganese. The 26 Mg(n,γ) 27 Mg reaction produces γ-rays of 0.843 MeV from the decay of 27 Mg, which interfere with the 0.847 MeV γ-rays from the decay of 56 Mn, produced by the 55 Mn(n,γ) 56 Mn reaction. Secondly, this work provides estimates of the levels of manganese to be expected in referent subjects. A revised estimate has been made from the most recent literature to explore the potential of the technique as a suitable means of screening patients and people exposed to excessive amounts of Mn who could develop many-fold increased levels of Mn in bones as demonstrated through various animal studies. This report presents the enhancements to the neutron activation system, by which manganese can be measured, which resulted in a detection limit in the hand of human subjects of 1.6

  9. Quantification of manganese in human hand bones: a feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Aslam; Pejovic-Milic, A; Chettle, D R; McNeill, F E [Department of Medical Physics and Applied Radiation Sciences, McMaster University, Hamilton, ON, L8S 4K1 (Canada)], E-mail: aslamib@mcmaster.ca

    2008-08-07

    Manganese is both an essential element to human health and also toxic when humans are exposed to excessive levels, particularly by means of inhalation. Biological monitoring of manganese exposure is problematic. It is subject to homeostasis; levels in blood (or serum/plasma) reflect only the most recent exposure and rapidly return to within normal ranges, even when there has been a temporary excursion in response to exposure. In this context, we have been developing a non-invasive technique for measurement of manganese stored in bone, using in vivo neutron activation analysis. Following preliminary feasibility studies, the technique has been enhanced by two significant infrastructure advances. A specially designed irradiation facility serves to maximize the activation of manganese with respect to the dose of ionizing radiation. Secondly, an array of eight NaI(Tl) crystals provides a detection system with very close to 4{pi} geometry. This feasibility study, using neutron activation analysis to measure manganese in the bones of the hand, takes two features into account. Firstly, there is considerable magnesium present in the bone and this produces a spectral interference with the manganese. The {sup 26}Mg(n,{gamma}){sup 27}Mg reaction produces {gamma}-rays of 0.843 MeV from the decay of {sup 27}Mg, which interfere with the 0.847 MeV {gamma}-rays from the decay of {sup 56}Mn, produced by the {sup 55}Mn(n,{gamma}){sup 56}Mn reaction. Secondly, this work provides estimates of the levels of manganese to be expected in referent subjects. A revised estimate has been made from the most recent literature to explore the potential of the technique as a suitable means of screening patients and people exposed to excessive amounts of Mn who could develop many-fold increased levels of Mn in bones as demonstrated through various animal studies. This report presents the enhancements to the neutron activation system, by which manganese can be measured, which resulted in a detection

  10. Fixing the Mirrors: A Feasibility Study of the Effects of Dance Movement Therapy on Young Adults with Autism Spectrum Disorder

    Science.gov (United States)

    Koch, Sabine C.; Mehl, Laura; Sobanski, Esther; Sieber, Maik; Fuchs, Thomas

    2015-01-01

    From the 1970s on, case studies reported the effectiveness of therapeutic mirroring in movement with children with autism spectrum disorder. In this feasibility study, we tested a dance movement therapy intervention based on mirroring in movement in a population of 31 young adults with autism spectrum disorder (mainly high-functioning and…

  11. Using a finite element pediatric hip model in clinical 2 evaluation - a feasibility study

    DEFF Research Database (Denmark)

    Skytte, T. L.; Mikkelsen, Lars Pilgaard; Sonne-Holm, Stig

    2017-01-01

    The paper describe a method to construct a finite element model of the hip joint of a child based on clinical recorded CT data. A model which can be used for diagnostic aid and pre-operative surgical evaluation. First part of this development is a feasibility study of this method. A scan...... to previous published experimental studies and computational models investigating the adult hip joint. Good correlation between the current model and previous models were found. The current case specific modeling technique may be a useful complement to the previously developed hip models....

  12. Development of Bioavailability Adjustment Factors: A Feasibility Study

    National Research Council Canada - National Science Library

    Rembish, Steve

    2000-01-01

    The primary purpose of this effort is to investigate the feasibility of developing and using bioavailability adjustment factors to modify intake assumptions used in risk assessments on a site-specific basis...

  13. Canton hydroelectric project: feasibility study. Final report, appendices

    Energy Technology Data Exchange (ETDEWEB)

    1979-05-01

    These appendices contain legal, environmental, regulatory, technical and economic information used in evaluating the feasibility of redeveloping the hydroelectric power generating facilities at the Upper and Lower Dams of the Farmington River at Collinsville, CT. (LCL)

  14. Qualitative Case Study Guidelines

    Science.gov (United States)

    2013-11-01

    Introduction to Sociological Methods. 2nd ed. New York, McGraw-Hill 14. Denzin , N. K. and Lincoln , Y. S. (2011) The SAGE Handbook of Qualitative...The Art of Science. In: Denzin , N. K. and Lincoln , Y. S. (eds.) Handbook of Qualitative Research. Thousand Oaks, Sage 19. GAO (1990) Case Study...Rinehart & Winston 39. Stake, R. E. (1994) Case Studies. In: Denzin , N. K. and Lincoln , Y. S. (eds.) Handbook of Qualitative Research. Thousand Oaks, Sage

  15. Ultrasound-Guided Intermediate Site Greater Occipital Nerve Infiltration: A Technical Feasibility Study.

    Science.gov (United States)

    Zipfel, Jonathan; Kastler, Adrian; Tatu, Laurent; Behr, Julien; Kechidi, Rachid; Kastler, Bruno

    2016-01-01

    Two studies recently reported that computed tomography (CT) guided infiltration of the greater occipital nerve at its intermediate site allows a high efficacy rate with long-lasting pain relief following procedure in occipital neuralgia and in various craniofacial pain syndromes. The purpose of our study was to evaluate the technical feasibility and safety of ultrasound-guided intermediate site greater occipital nerve infiltration. Retrospective study. This study was conducted at the imaging department of a 1,409 bed university hospital. Local institutional review board approval was obtained and written consent was waived. In this retrospective study, 12 patients suffering from refractory occipital neuralgia or craniofacial pain syndromes were included between April and October 2014. They underwent a total of 21 ultrasound-guided infiltrations. Infiltration of the greater occipital nerve was performed at the intermediate site of the greater occipital nerve, at its first bend between obliqus capitis inferior and semispinalis capitis muscles with local anestetics and cortivazol. Technical success was defined as satisfactory diffusion of added iodinated contrast media in the fatty space between these muscles depicted on control CT scan. We also reported first data of immediate block test efficacy and initial clinical efficacy at 7 days, one month, and 3 months, defined by a decrease of at least 50% of visual analog scale (VAS) scores. Technical success rate was 95.24%. Patients suffered from right unilateral occipital neuralgia in 3 cases, left unilateral occipital neuralgia in 2 cases, bilateral occipital neuralgia in 2 cases, migraine in one case, cervicogenic headache in one case, tension-type headache in 2 cases, and cluster headache in one case. Block test efficacy was found in 93.3% (14/15) cases. Clinical efficacy was found in 80% of cases at 7 days, in 66.7% of cases at one month and in 60% of cases at 3 months. No major complications were noted. Some of the

  16. Computing with words to feasibility study of software projects

    Directory of Open Access Journals (Sweden)

    Marieta Peña Abreu

    2017-02-01

    Full Text Available Objective: This paper proposes a method to analyze the technical, commercial and social feasibility of software projects in environments of uncertainty. It allows working with multiple experts and multiple criteria and facilitates decision-making. Method: The proposal contains two phases, first the necessary information is collected and in second place projects are evaluated using 2-tuple linguistic representation model. The experts are selected by analyzing their curricular synthesis. The evaluation criteria are defined using the technique Focus Group and weighted in the interval (0,1 according to their importance. three domains are offered to express the preferences: numeric, interval-valued and linguistic. For aggregation extended arithmetic mean and weighted average extended are used, preventing the loss of information. A 2-tuple (feasibility, precision is obtained as a result for each project. Results: The evaluation of P1 project was a very high feasibility with -0,33 of precision. The P2 project obtained a high feasibility with 0,38 of precision and P3 project achieved a medium feasibility with -0,21 of precision. Conclusions: This method is favorable for software projects feasibility analysis with presence of multiple experts and criteria, in environments of uncertainty. It tries heterogeneous assessments without loss of information. Their results are consistent and useful for decision makers.

  17. Feasibility studies for a wireless 60 GHz tracking detector readout

    International Nuclear Information System (INIS)

    Dittmeier, S.; Schöning, A.; Soltveit, H.K.; Wiedner, D.

    2016-01-01

    The amount of data produced by highly granular silicon tracking detectors in high energy physics experiments poses a major challenge to readout systems. At high collision rates, e.g. at LHC experiments, only a small fraction of data can be read out with currently used technologies. To cope with the requirements of future or upgraded experiments new data transfer techniques are required which offer high data rates at low power and low material budget. Wireless technologies operating in the 60 GHz band or at higher frequencies offer high data rates and are thus a promising upcoming alternative to conventional data transmission via electrical cables or optical fibers. Using wireless technology, the amount of cables and connectors in detectors can be significantly reduced. Tracking detectors profit most from a reduced material budget as fewer secondary particle interactions (multiple Coulomb scattering, energy loss, etc.) improve the tracking performance in general. We present feasibility studies regarding the integration of the wireless technology at 60 GHz into a silicon tracking detector. We use spare silicon strip modules of the ATLAS experiment as test samples which are measured to be opaque in the 60 GHz range. The reduction of cross talk between links and the attenuation of reflections is studied. An estimate of the maximum achievable link density is given. It is shown that wireless links can be placed as close as 2 cm next to each other for a layer distance of 10 cm by exploiting one or several of the following measures: highly directive antennas, absorbers like graphite foam, linear polarization and frequency channeling. Combining these measures, a data rate area density of up to 11 Tb/(s·m"2) seems feasible. In addition, two types of silicon sensors are tested under mm-wave irradiation in order to determine the influence of 60 GHz data transmission on the detector performance: an ATLAS silicon strip sensor module and an HV-MAPS prototype for the Mu3e

  18. Feasibility studies for a wireless 60 GHz tracking detector readout

    Energy Technology Data Exchange (ETDEWEB)

    Dittmeier, S., E-mail: dittmeier@physi.uni-heidelberg.de; Schöning, A.; Soltveit, H.K.; Wiedner, D.

    2016-09-11

    The amount of data produced by highly granular silicon tracking detectors in high energy physics experiments poses a major challenge to readout systems. At high collision rates, e.g. at LHC experiments, only a small fraction of data can be read out with currently used technologies. To cope with the requirements of future or upgraded experiments new data transfer techniques are required which offer high data rates at low power and low material budget. Wireless technologies operating in the 60 GHz band or at higher frequencies offer high data rates and are thus a promising upcoming alternative to conventional data transmission via electrical cables or optical fibers. Using wireless technology, the amount of cables and connectors in detectors can be significantly reduced. Tracking detectors profit most from a reduced material budget as fewer secondary particle interactions (multiple Coulomb scattering, energy loss, etc.) improve the tracking performance in general. We present feasibility studies regarding the integration of the wireless technology at 60 GHz into a silicon tracking detector. We use spare silicon strip modules of the ATLAS experiment as test samples which are measured to be opaque in the 60 GHz range. The reduction of cross talk between links and the attenuation of reflections is studied. An estimate of the maximum achievable link density is given. It is shown that wireless links can be placed as close as 2 cm next to each other for a layer distance of 10 cm by exploiting one or several of the following measures: highly directive antennas, absorbers like graphite foam, linear polarization and frequency channeling. Combining these measures, a data rate area density of up to 11 Tb/(s·m{sup 2}) seems feasible. In addition, two types of silicon sensors are tested under mm-wave irradiation in order to determine the influence of 60 GHz data transmission on the detector performance: an ATLAS silicon strip sensor module and an HV-MAPS prototype for the Mu3e

  19. The feasibility of a fiber optic laser approach to relieving lymphedematous syndrome: a case report

    Directory of Open Access Journals (Sweden)

    Palmieri B

    2013-02-01

    Full Text Available Beniamino Palmieri,1,2 Alessandro Di Cerbo,1,2 Valentina Rottigni,1,2 Gregorio Fistetto,2 Tommaso Iannitti2,31University of Modena, Department of General Surgery and Surgical Specialties, 2Poliambulatorio del Secondo Parere, Modena, Italy; 3University of Kentucky, Department of Physiology, Lexington, KY, USAAbstract: Here we report a case of successful fiber optic laser treatment of lymphedema in a swollen arm post mastectomy. At the moment, this procedure has only anecdotal evidence to justify its use, but in our experience is a feasible, minimally invasive day-stay procedure which has been demonstrated to be safe and effective. Further nonhomogeneous case pooling and follow-up would enable guidelines and definite surgical protocols for its use to be implemented.Keywords: fiber optic, lymphedema, Nd:YAG, laser, mastectomy

  20. Feasibility study of an image slicer for future space application

    Science.gov (United States)

    Calcines, A.; Ichimoto, K.

    2014-08-01

    This communication presents the feasibility study of an image slicer for future space missions, especially for the integral field unit (IFU) of the SUVIT (Solar UV-Visible-IR telescope) spectro-polarimeter on board the Japanese-led solar space mission Solar-C as a backup option. The MuSICa (Multi-Slit Image slicer based on collimator-Camera) image slicer concept, originally developed for the European Solar Telescope, has been adapted to the SUVIT requirements. The IFU will reorganizes a 2-D field of view of 10 x 10 arcsec2 into three slits of 0.18 arcsec width by 185.12 arcsec length using flat slicer mirrors of 100 μm width. The layout of MuSICa for Solar-C is telecentric and offers an optical quality limited by diffraction. The entrance for the SUVIT spectro-polarimeter is composed by the three IFU slits and one ordinal long slit to study, using high resolution spectro-polarimetry, the solar atmosphere (Photosphere and Chromosphere) within a spectral range between 520 nm (optionally 280 nm) and 1,100 nm.

  1. Feasibility study of a 1-MW pulsed spallation source

    International Nuclear Information System (INIS)

    Cho, Y.; Chae, Y.C.; Crosbie, E.

    1995-01-01

    A feasibility study of a 1-MW pulsed spallation source based on a rapidly cycling proton synchrotron (RCS) has been completed. The facility consists of a 400-MeV HP - linac, a 30-Hz RCS that accelerates the 400-MeV beam to 2 GeV, and two neutron-generating target stations. The design time-averaged current of the accelerator system is 0.5 mA, or 1.04x1014 protons per pulse. The linac system consists of an H - ion source, a 2-MeV RFQ, a 70-MeV DTL and a 330-MeV CCL. Transverse phase space painting to achieve a Kapchinskij-Vladimirskij (K-V) distribution of the injected particles in the RCS is accomplished by charge exchange injection and programming of the closed orbit during injection. The synchrotron lattice uses FODO cells of ∼90 degrees phase advance. Dispersion-free straight sections are obtained by using a missing magnet scheme. Synchrotron magnets are powered by a dual-frequency resonant circuit that excites the magnets at a 20-Hz rate and de-excites them at a 60-Hz rate, resulting in an effective rate of 30 Hz, and reducing the required peak rf voltage by 1/3. A key feature, of the design of this accelerator system is that beam losses are from injection to extraction, reducing activation to levels consistent with hands-on maintenance. Details of the study are presented

  2. A Pilot Feasibility Study to Improve Food Parenting Practices.

    Science.gov (United States)

    Moore, Amy M; Clair-Michaud, Mary; Melanson, Kathleen J; Tovar, Alison

    2018-03-01

    We examined the feasibility and acceptability of a novel home-based intervention to improve the food parenting practices of low-income mothers with preschool-aged children. Mother-child dyads (N = 15) were recruited from WIC in southern Rhode Island. A non-experimental, pretest-posttest design was used to assess changes in maternal food parenting practices. Dyads participated in 3 home-based sessions that included baseline measures and an evening meal video recording at session 1, a motivational interviewing (MI) intervention that included feedback on the evening meal video recording at session 2, and a satisfaction ques- tionnaire at session 3. Pretest-posttest measures included 5 subscales of the Comprehensive Feeding Practices Questionnaire. Fifteen mother-child dyads (mothers: 32.3, SD = 4.6 years, 86.7% white; children: 3.2, SD = 0.9 years, male = 73.3%, 66.7% white) completed the study. Mothers reported improvements in food parenting practices following the home-based MI intervention. Overall, 93% of mothers 'strongly agreed' that it was worth their effort to participate in the study. A home-based MI intervention may be an effective strategy for improving maternal food parenting practices in low-income populations. Most mothers found that watching themselves was informative and applicable to their own lives.

  3. Feasibility Pilot Study: Training Soft Skills in Virtual Worlds.

    Science.gov (United States)

    Abshier, Patricia

    2012-04-01

    In a world where funding is limited, training for healthcare professionals is turning more and more to distance learning in an effort to maintain a knowledgeable and skilled work force. In 2010, Cicatelli Associates, Inc. began exploring the feasibility of using games and virtual worlds as an alternative means to teach skills-training in a distance-learning environment. The pilot study was conducted with six individuals familiar with general counseling and communication skills used by the healthcare industry to promote behavior change. Participants reported that the venue, although challenging at first, showed great potential for use with healthcare providers, as it allowed for more interaction and activities than traditional Webinars. However, there are significant limitations that must be overcome in order for this healthcare training modality to be utilized on a large scale. These limitations included a lack of microgestures and issues regarding the technology being used. In spite of the limitations, however, the potential use of virtual worlds for the training of healthcare providers exists and should be researched further. This article discusses the need and intended benefits of virtual world training as well as the results and conclusions of the pilot study.

  4. Feasibility of a responsive business scorecard - a pilot study

    NARCIS (Netherlands)

    van der Woerd, K.F.; van den Brink, T.W.M.

    2004-01-01

    Several authors have pointed at opportunities to develop the well-established Business Balanced Scorecard into a Scorecard that enables companies to integrate sustainability into their strategy. Recent case studies and research experiences show that social and environmental targets are more widely

  5. Intrathoracic pressure regulation during cardiopulmonary resuscitation: a feasibility case-series.

    Science.gov (United States)

    Segal, Nicolas; Parquette, Brent; Ziehr, Jonathon; Yannopoulos, Demetris; Lindstrom, David

    2013-04-01

    Intrathoracic pressure regulation (IPR) is a novel, noninvasive therapy intended to increase cardiac output and blood pressure in hypotensive states by generating a negative end expiratory pressure of -12 cm H2O between positive pressure ventilations. In this first feasibility case-series, we tested the hypothesis that IPR improves End tidal (ET) CO2 during cardiopulmonary resuscitation (CPR). ETCO2 was used as a surrogate measure for circulation. All patients were treated initially with manual CPR and an impedance threshold device (ITD). When IPR-trained medics arrived on scene the ITD was removed and an IPR device (CirQLATOR™) was attached to the patient's advanced airway (intervention group). The IPR device lowered airway pressures to -9 mmHg after each positive pressure ventilation for the duration of the expiratory phase. ETCO2, was measured using a capnometer incorporated into the defibrillator system (LifePak™). Values are expressed as mean ± SEM. Results were compared using paired and unpaired Student's t test. p values of <0.05 were considered statistically significant. ETCO2 values in 11 patients in the case series were compared pre and during IPR therapy and also compared to 74 patients in the control group not treated with the new IPR device. ETCO2 values increased from an average of 21 ± 1 mmHg immediately before IPR application to an average value of 32 ± 5 mmHg and to a maximum value of 45 ± 5mmHg during IPR treatment (p<0.001). In the control group ETCO2 values did not change significantly. Return of spontaneous circulation (ROSC) rates were 46% (34/74) with standard CPR and ITD versus 73% (8/11) with standard CPR and the IPR device (p<0.001). ETCO2 levels and ROSC rates were significantly higher in the study intervention group. These findings demonstrate that during CPR circulation may be significantly augmented by generation of a negative end expiratory pressure between each breath. Copyright © 2012 Elsevier Ireland Ltd. All rights

  6. Community pharmacy-based case finding for COPD in urban and rural settings is feasible and effective

    Directory of Open Access Journals (Sweden)

    Fathima M

    2017-09-01

    Full Text Available Mariam Fathima,1 Bandana Saini,1,2 Juliet M Foster,1 Carol L Armour1,3 1Woolcock Institute of Medical Research, Sydney Medical School, 2Faculty of Pharmacy, The University of Sydney, 3Central Sydney Area Health Service, Sydney, NSW, Australia Background and objective: Case finding of patients at risk of COPD by community pharmacists could identify a substantial number of people with undiagnosed COPD, but little is known about the feasibility and effectiveness of pharmacy-based COPD case finding using microspirometry. The objective of this study was to assess the feasibility and effectiveness of COPD case-finding service provided by community pharmacists, utilizing a combination of risk assessment questionnaire and microspirometry. Methods: A 6-month service was conducted in 21 community pharmacies in Australia. Pharmacists trained in COPD case finding, including lung function test (LFT, invited their patients aged ≥35 years with a history of smoking and/or respiratory symptoms to participate. High-risk patients were identified via a COPD risk assessment questionnaire (Initial Screening Questionnaire [ISQ] and underwent LFT. Pharmacists referred patients with a forced expiratory volume in 1 second (FEV1/forced expiratory volume in 6 seconds (FEV6 ratio <0.75 to their general practitioner (GP for further assessment and diagnosis. Results: In all, 91 of 167 (54% patients had an ISQ score >3 indicating high COPD risk. Of the 157 patients who were able to complete LFT, 61 (39% had an FEV1/FEV6 ratio of <0.75 and were referred to their GP. Patients with high ISQ symptoms scores (>3 were at a significantly higher risk of an FEV1/FEV6 ratio of <0.75, compared to patients with fewer COPD symptoms. A total of 15 (10% patients were diagnosed with COPD by their GP. Another eight (5% patients were diagnosed with other medical conditions and 87% of these were initiated on treatment. Although only half of all screened patients lived in regional areas, 93

  7. Computed tomography with energy-resolved detection: a feasibility study

    Science.gov (United States)

    Shikhaliev, Polad M.

    2008-03-01

    The feasibility of computed tomography (CT) with energy-resolved x-ray detection has been investigated. A breast CT design with multi slit multi slice (MSMS) data acquisition was used for this study. The MSMS CT includes linear arrays of photon counting detectors separated by gaps. This CT configuration allows for efficient scatter rejection and 3D data acquisition. The energy-resolved CT images were simulated using a digital breast phantom and the design parameters of the proposed MSMS CT. The phantom had 14 cm diameter and 50/50 adipose/glandular composition, and included carcinoma, adipose, blood, iodine and CaCO3 as contrast elements. The x-ray technique was 90 kVp tube voltage with 660 mR skin exposure. Photon counting, charge (energy) integrating and photon energy weighting CT images were generated. The contrast-to-noise (CNR) improvement with photon energy weighting was quantified. The dual energy subtracted images of CaCO3 and iodine were generated using a single CT scan at a fixed x-ray tube voltage. The x-ray spectrum was electronically split into low- and high-energy parts by a photon counting detector. The CNR of the energy weighting CT images of carcinoma, blood, adipose, iodine, and CaCO3 was higher by a factor of 1.16, 1.20, 1.21, 1.36 and 1.35, respectively, as compared to CT with a conventional charge (energy) integrating detector. Photon energy weighting was applied to CT projections prior to dual energy subtraction and reconstruction. Photon energy weighting improved the CNR in dual energy subtracted CT images of CaCO3 and iodine by a factor of 1.35 and 1.33, respectively. The combination of CNR improvements due to scatter rejection and energy weighting was in the range of 1.71-2 depending on the type of the contrast element. The tilted angle CZT detector was considered as the detector of choice. Experiments were performed to test the effect of the tilting angle on the energy spectrum. Using the CZT detector with 20° tilting angle decreased the

  8. Structural Design Feasibility Study for the Global Climate Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Lewin,K.F.; Nagy, J.

    2008-12-01

    Neon, Inc. is proposing to establish a Global Change Experiment (GCE) Facility to increase our understanding of how ecological systems differ in their vulnerability to changes in climate and other relevant global change drivers, as well as provide the mechanistic basis for forecasting ecological change in the future. The experimental design was initially envisioned to consist of two complementary components; (A) a multi-factor experiment manipulating CO{sub 2}, temperature and water availability and (B) a water balance experiment. As the design analysis and cost estimates progressed, it became clear that (1) the technical difficulties of obtaining tight temperature control and maintaining elevated atmospheric carbon dioxide levels within an enclosure were greater than had been expected and (2) the envisioned study would not fit into the expected budget envelope if this was done in a partially or completely enclosed structure. After discussions between NEON management, the GCE science team, and Keith Lewin, NEON, Inc. requested Keith Lewin to expand the scope of this design study to include open-field exposure systems. In order to develop the GCE design to the point where it can be presented within a proposal for funding, a feasibility study of climate manipulation structures must be conducted to determine design approaches and rough cost estimates, and to identify advantages and disadvantages of these approaches including the associated experimental artifacts. NEON, Inc requested this design study in order to develop concepts for the climate manipulation structures to support the NEON Global Climate Experiment. This study summarizes the design concepts considered for constructing and operating the GCE Facility and their associated construction, maintenance and operations costs. Comparisons and comments about experimental artifacts, construction challenges and operational uncertainties are provided to assist in selecting the final facility design. The overall goal

  9. Feasibility study on waste utilization of a palm oil refinery

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to empty fruit bunches (EFB) which are wasted at the Lahad Datu plant of Felda Vegetable Oil Products Co. in Malaysia, a project was studied for energy substitution and greenhouse effect gas reduction by fluidized bed cogeneration facilities using this as fuel. In the project, studied was the introduction of on-site cogenerator of 7,800kW in generating-end output, and that of IPP cogenerator of 16,000kW as reference. As a result of the study, the energy substitution amount in toe in 20 years was approximately 376 k tons in case of on-site power generation/fluidized bed boiler and approximately 695 k tons in case of IPP and fluidized bed boiler. The amount of greenhouse effect gas emission in toe in 20 years was approximately 5,757 k tons and 11,654 k tons, respectively. Concerning the profitability, the internal earning rate was 3.32-8.47% in case of on-site power generation/fluidized bed boiler and 9.13-14.65% in case of IPP/fluidized bed boiler. It indicated the materialization of the project. (NEDO)

  10. Feasibility study of medical isotope production at Sandia National Laboratories

    International Nuclear Information System (INIS)

    Massey, C.D.; Miller, D.L.; Carson, S.D.

    1995-12-01

    In late 1994, Sandia National Laboratories in Albuquerque, New Mexico, (SNL/NM), was instructed by the Department of Energy (DOE) Isotope Production and Distribution Program (IPDP) to examine the feasibility of producing medically useful radioisotopes using the Annular Core Research Reactor (ACRR) and the Hot Cell Facility (HCF). Los Alamos National Laboratory (LANL) would be expected to supply the targets to be irradiated in the ACRR. The intent of DOE would be to provide a capability to satisfy the North American health care system demand for 99 Mo, the parent of 99m Tc, in the event of an interruption in the current Canadian supply. 99m Tc is used in 70 to 80% of all nuclear medicine procedures in the US. The goal of the SNL/NM study effort is to determine the physical plant capability, infrastructure, and staffing necessary to meet the North American need for 99 Mo and to identify and examine all issues with potential for environmental impact

  11. Feasibility study of patient motion monitoring using tactile array sensor

    International Nuclear Information System (INIS)

    Kim, Tae Ho; Kang, Seong Hee; Kim, Dong Su; Cho, Min Seok; Kim, Kyeong Hyeon; Suh, Tae Suk; Kim, Si Yong

    2014-01-01

    The aim of this study is to evaluate patient pretreatment set-up error and intra-fraction motion using the tactile array sensors (Pressure Profile Systems Inc, Los Angeles, CA) which could measure distributed pressure profiles along the contacting surface and to check a feasibility of the sensor (tactile array sensor) in the patient motion monitoring. Laser alignment and optical camera based monitoring system are very useful for reduce patient set-up error but these systems could not monitor the blind area like patient's back position. Actually after patient alignment using laser or optical monitoring system, it was assumed that there is no error in the patient's back position (pressure profile distribution). But if an error occurs in the patient's back position, it will affect the radiation therapy accuracy. In spite of optical motion monitoring or using the immobilization tool, distributed pressure profiles of patient's back position was changed during inter and intra-fraction. For more accurate patient set-up, blind area (patient's back) monitoring was necessary. We expect that the proposed method will be very useful for make up for the weakness of optical monitoring method

  12. Duet for menstrual protection: a feasibility study in Zimbabwe.

    Science.gov (United States)

    Averbach, Sarah; Sahin-Hodoglugil, Nuriye; Musara, Petina; Chipato, Tsungai; van der Straten, Ariane

    2009-06-01

    Managing menses is a challenge for women in developing countries. Duet is a cervical barrier being developed for contraception and STI prevention. We explored the hypothetical acceptability of using Duet as a menstrual cup, among Zimbabwean women. A survey and focus group discussions (FGD) were conducted with 43 women aged 18-45 years to gain information about their menstrual practices and attitudes regarding the use of Duet for menstrual protection. All 43 women reported that if Duet were available, they would "definitely" try it, and that it was "very important" that Duet is low cost and easy to clean; 86% reported that using it would make a difference in their lives. FGD findings highlighted unhygienic practices due to the lack of affordable options for menstrual management and a genuine interest in Duet, including its potential use for multiple purposes (contraception, disease prevention and menstrual protection). Accessing affordable and hygienic menstrual protection was a problem for these Zimbabwean women. Duet appeared acceptable and it would be feasible to conduct a user-acceptability study of Duet as a menstrual cup in Zimbabwe.

  13. Feasibility study of a soil-based rubberized CLSM.

    Science.gov (United States)

    Wu, Jason Y; Tsai, Mufan

    2009-02-01

    The development of beneficial uses of recycled scrap tires is always in great demand around the world. The disposal of on-site surplus excavated soil and the production of standard engineering aggregates have also been facing increasing environmental and ecological challenges in congested islands, such as Taiwan. This paper presents an experimental study using recycled crumb rubber and native silty sand to produce a lightweight, soil-based, rubberized controlled low strength material (CLSM) for a bridge approach repair. To assess the technical feasibility of this material, the effects of weight ratios of cement-to-water (C/W) and water-to-solid (W/S), and of rubber content on the engineering properties for different mixtures were investigated. The presented test results include flowability, unit weight, strength, settlement potential, and bearing capacity. Based on the findings, we conclude that a soil-based rubberized CLSM with 40% sand by weight and an optimal design ratio of 0.7 for C/W and 0.35 for W/S can be used for the proposed bridge approach repair. Such a mixture has demonstrated acceptable flowability, strength, and bearing capacity. Its lower unit weight, negligible compressibility, and hydrocollapse potential also help ensure that detrimental settlement is unlikely to occur. The results illustrate a novel scheme of CLSM production, and suggest a beneficial alternative for the reduction of scrap tires as well as conservation of resources and environment.

  14. Proceedings of the remedial investigation/feasibility study workshop

    International Nuclear Information System (INIS)

    1988-12-01

    The objective of this workshop was to familiarize Department of Energy (DOE) personnel and contractors with all aspects of developing, managing, and conducting an RI/FS, based on HAZWRAP SCO experience in similar activities as part of the Installation Restoration program (IRP). The HAZWRAP SCO participation in Department of Defense (DOD) restoration activities provides an opportunity to develop capability and experience which are transferable to DOE activities. Paul Franco, Program Manager for the IRP, provided an overview of the IRP experience in conducting an RI/FS for a National Priorities List (NPL) site and a non-NPL site. A non-NPL site does not require an RI/FS by regulation; however, the RI/FS process can be used to determine whether to proceed with a feasibility study or terminate the action with a decision document. Al Porell, Program Manager for ICP, discussed the use of decision documents to remove non-NPL sites from regulatory consideration. DOE-Idaho has used similar documentation to remove numerous sites from their list of potential remedial action sites. Mr. Porell also discussed the use of the Technical Review Committee (TRC), which is established to coordinate activities during the RI/FS process. The TRC includes state, local, and federal authorities, and Air Force installation personnel

  15. Preparing a feasibility study for a maglev transport system

    Energy Technology Data Exchange (ETDEWEB)

    Kessel, H

    1984-06-01

    The Transrapid test facility in Emsland is almost completed, and the phase of putting into operation with the TR 06 maglev vehicle has commenced. This will be followed by a general test phase to check the practicability of the maglev system. It is now time to clarify, by means of a feasibility study, what steps are necessary for the introduction of the maglev system in West Germany. Taking two existing railway lines as example, namely Hamburg-Hannover and Duesseldorf Airport-Cologne/Bonn Airport, the effect will be examined of the public-law licensing procedure, participation of the general public in planning procedures, and the information of the media. Also, the technical framework data will be revised on the basis of the experience gained in building the Transrapid facility and the technical improvements made subsequently. Proposed track routing plans are to take particular account of environmental protection considerations, while cost accounting models will be developed which allow fast and reliable forecasts to be made for future projects in respect of investment and operating costs, and optimal operating procedures will be determined by means of simulation.

  16. Exercise for Adolescents with Depressive Disorders: A Feasibility Study

    Directory of Open Access Journals (Sweden)

    Richard R. Dopp

    2012-01-01

    Full Text Available Objectives. Adolescence is associated with increased depressive symptoms and decreased aerobic exercise, yet the relationship between exercise and clinical depression among adolescents requires further examination. This study assessed the feasibility of a 12-week intervention designed to increase exercise for adolescents with depressive disorders: Will a teenager with depression exercise? Methods. Participants were 13 adolescents with depression reporting low levels of aerobic exercise. They completed a 12-week intervention (15 supervised exercise sessions and 21 independent sessions. Exercise was measured through the aerobic exercise Questionnaire, actigraphy, and heart-rate monitoring. Depression was measured with the Children’s Depression Rating Scale, Revised, and Quick Inventory of Depressive Symptomatology, Self-Report. Results. All participants who started the intervention completed the protocol, attending all supervised exercise sessions. Actigraphy verified 81% adherence to the protocol’s independent sessions. Analysis of secondary outcomes showed a significant increase in exercise levels and a significant decrease in depression severity. Initially, ten participants were overweight or obese, and three were healthy weight. After 12 weeks of exercise, the number of participants in the healthy-weight category doubled. Conclusions. Adolescents suffering from depression can complete a rigorous protocol requiring structured increases in aerobic exercise. Participants showed significant increases in exercise, and significant decreases in depressive symptoms.

  17. Sitewide feasibility study Eielson Air Force Base, Alaska

    Energy Technology Data Exchange (ETDEWEB)

    Last, G.V.; Lanigan, D.C.; Josephson, G.B.; Bagaasen, L.M.

    1995-09-01

    The Sitewide Feasibility Study (FS) is required under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), the National Contingency Plan (NCP), and the Federal Facility Agreement (FFA) for Eielson Air Force Base (AFB). It is based on findings presented in the Sitewide Remedial Investigation (RI) Report (USAF 1995a), and the Sitewide Baseline Risk Assessment (BLRA) Report (USAF 1995b). Under the FFA, 64 potential source areas were placed in one of six operable units, based on similar contaminant and environmental characteristics, or were included for evaluation under a Source Evaluation Report (SER). The sitewide RI was directed at contamination that was not confined to an operable unit (OU) or SER source area. The objectives of the sitewide RI were to: Provide information about site characteristics to support individual OU RI/FS efforts and the sitewide RI/FS, including site hydrogeology and determination of background soil and groundwater characteristics; identify and characterize contamination that is not confined or attributable to a specific source area through sitewide monitoring of groundwater and surface water; evaluate cumulative risks to human health and the environment from contamination on a sitewide basis; and provide a mechanism for continued cohesive sitewide monitoring.

  18. Revised CTUIR Renewable Energy Feasibility Study Final Report

    Energy Technology Data Exchange (ETDEWEB)

    John Cox; Thomas Bailor; Theodore Repasky; Lisa Breckenridge

    2005-10-31

    This preliminary assessment of renewable energy resources on the Umatilla Indian Reservation (UIR) has been performed by CTUIR Department of Science and Engineering (DOSE). This analysis focused primarily identifying renewable resources that may be applied on or near the Umatilla Indian Reservation. In addition preliminary technical and economic feasibility of developing renewable energy resources have been prepared and initial land use planning issues identified. Renewable energies examined in the course of the investigation included solar thermal, solar photovoltaic, wind, bioethanol, bio-diesel and bio-pellet fuel. All renewable energy options studied were found to have some potential for the CTUIR. These renewable energy options are environmentally friendly, sustainable, and compliment many of the policy goals of the CTUIR. This report seeks to provide an overall review of renewable energy technologies and applications. It tries to identify existing projects near to the CTUIR and the efforts of the federal government, state government and the private sector in the renewable energy arena. It seeks to provide an understanding of the CTUIR as an energy entity. This report intends to provide general information to assist tribal leadership in making decisions related to energy, specifically renewable energy deve lopment.

  19. Feasibility study on utilization of associated gas as CNG

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Back Ho oilfield is the largest oilfield in Vietnam and at the same time is producing the largest amount of natural gas (associated gas) in Vietnam. Although the majority of the associated gas has been used in the power generation plant, a large amount of surplus gas is not effectively used because of shortage of fund and technologies. Accordingly, a feasibility study has been executed for a project to compress 20% of the associated gas into CNG, and use it effectively as automobile and factory fuel. As a result of the site survey, it was found that, although Vietnam consumes less amount of energy and emits less amount of CO2, the nation has a strong interest and a large amount of knowledge about global warming and CDM because the country is subjected to large effect of warming. Furthermore, it has been reconfirmed that introducing CNG into this territory is highly effective. Discussions have been made on places of installing the facilities, effective surplus gas utilization systems, facility specifications, utilities, and number of workers. Calculations were made on approximate cost of the facilities and the running cost. As a result of the surveys and discussions, it was determined that technological support from Japan and the Yen loan for environment with low interest rate are necessary. (NEDO)

  20. Fort Yukon, Chalkyitsik, & Venetie Biomass Boiler Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Greg Koontz, ME William A. Wall, PhD

    2009-03-31

    The Council of Athabascan Tribal Governments (CATG) is a consortium of ten Gwich'in and Koyukon Athabascan tribes settled in 10 remote villages and are linked by the Yukon River System. The CATG mission is to maintain the Yukon Flats region as Indian Country by asserting traditional rights and taking responsibility for developing tribal technical capacity to manage the land and resources. It is the intent of CATG to explore and develop all opportunities for a renewable and self-sufficient energy program for each of the villages. CATG envisions utilization of forest resources both for construction and energy as one of the best long-term strategies for integrating the economic goals for the region as well as supporting the cultural and social issues. The intent for this feasibility project is to focus specifically on biomass utilization for heat, first, and for future electrical generation within the region, second. An initial determination has already been made regarding the importance of wood energy as a primary source of renewable energy to displace diesel fuel in the Yukon Flats region. A desktop study of other potential renewable resources was conducted in 2006.

  1. Endoscopic colostomy with percutaneous colopexy: an animal feasibility study.

    Science.gov (United States)

    Bustamante-Lopez, Leonardo Alfonso; Sulbaran, Marianny; Nahas, Sergio Carlos; de Moura, Eduardo Guimaraes Horneaux; Nahas, Caio Sergio; Marques, Carlos Frederico; Sakai, Christiano; Cecconello, Ivan; Sakai, Paulo

    2017-04-01

    Indications for colostomy in colorectal diseases are obstruction of the large bowel, such as in cancer, diverticular disease in the acute phase, post-radiotherapy enteritis, complex perirectal fistulas, anorectal trauma and severe anal incontinence. Some critically ill patients cannot tolerate an exploratory laparotomy, and laparoscopic assisted colostomy also requires general anesthesia. To evaluate the feasibility, safety and efficacy of performing colostomy assisted by colonoscopy and percutaneous colopexy. Five pigs underwent endoscopic assisted colostomy with percutaneous colopexy. Animals were evaluated in post-operative days 1, 2, 5 and 7 for feeding acceptance and colostomy characteristics. On day 7 full colonoscopy was performed on animals followed by exploratory laparotomy. Average procedure time was 27 minutes (21-54 min). Postoperative mobility and feeding of animals were immediate after anesthesia recovery. Position of the colostomy, edges color, appearance of periostomal area, as well as its function was satisfactory in four animals. Retraction of colostomy was present in one pig. The colonoscopy and laparotomy control on the seventh day were considered as normal. A bladder perforation that was successfully repaired through the colostomy incision occurred in one pig. The main limitation of this study is its experimental nature. Endoscopic assisted colostomy with percutaneous colopexy proves to be a safe and effective method with low morbidity for performing colostomy in experimental animals, with possible clinical application in humans.

  2. Feasibility study of tank leakage mitigation using subsurface barriers

    International Nuclear Information System (INIS)

    Treat, R.L.; Peters, B.B.; Cameron, R.J.; McCormak, W.D.; Trenkler, T.; Walters, M.F.; Rouse, J.K.; McLaughlin, T.J.; Cruse, J.M.

    1994-01-01

    The US Department of Energy (DOE) has established the Tank Waste Remediation System (TWRS) to satisfy manage and dispose of the waste currently stored in the underground storage tanks. The retrieval element of TWRS includes a work scope to develop subsurface impermeable barriers beneath SSTs. The barriers could serve as a means to contain leakage that may result from waste retrieval operations and could also support site closure activities by facilitating cleanup. Three types of subsurface barrier systems have emerged for further consideration: (1) chemical grout, (2) freeze walls, and (3) desiccant, represented in this feasibility study as a circulating air barrier. This report contains analyses of the costs and relative risks associated with combinations retrieval technologies and barrier technologies that from 14 alternatives. Eight of the alternatives include the use of subsurface barriers; the remaining six nonbarrier alternative are included in order to compare the costs, relative risks and other values of retrieval with subsurface barriers. Each alternative includes various combinations of technologies that can impact the risks associated with future contamination of the groundwater beneath the Hanford Site to varying degrees. Other potential risks associated with these alternatives, such as those related to accidents and airborne contamination resulting from retrieval and barrier emplacement operations, are not quantitatively evaluated in this report

  3. Feasibility study on modernization of North Bangkok Thermal Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to save energies and reduce global warming gas emission, a feasibility study was performed on the oil burning thermal power plant in the city of North Bangkok in Thailand to reconstruct the plant into a natural gas burning combined cycle power plant. In the project, the old facilities with an output of 237.8 MW using three steam turbines in total will be reconstructed into a plant comprising of two steam turbines for 256,2 MW and two gas turbines for 460.4 MW, or a facility of 716.6 MW in total. The plant construction will have the gas turbines, steam turbines, generators, and a waste heat recovered steam generator fixed on one axis, two of which will be installed. The gas turbines will use natural gas as fuel, and the steam turbines will be operated by steam from the waste heat recovered steam generator. As a result of the discussions, the reduction of the energy consumption for a period of 40 years will correspond to crude oil of 20,560 kt, while the reduction of the global warming gas emission will be 107,200 t-CO2. In addition, the energy saving cost will be 9-ton crude oil equivalent/one million yen, and the cost for reduction of the global warming gas emission will be 47 t-CO2/one million yen. (NEDO)

  4. Feasibility study on rehabilitation of ICE San Antonio Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Costa Rica takes a power generation system using hydro power generation as the main source, and possesses medium-capacity gas turbines to supplement needs in the dry season and the peak load. However, a problem has come up that, in addition to the cost rise in gas turbine fuel, the power generation efficiency has been aggravating due to aged deterioration of the generators being used. In association therewith, the problem is now a factor to increase CO2 emission, which is a worldwide problem. Keeping in mind to link it to the clean development mechanism (CDM), the present project is, taking up the SAN ANTONIO power plant as the investigation object, intended to perform a comprehensive discussion on the CO2 emission reducing effect, profitability, and proliferation effect, by executing the conceptual plant design. The up-grading plan for thermal power generation systems in Costa Rica consists of replacement of the gas turbines, handling of phase modifiers, and achievement of the combined cycle. The plan agrees with the present feasibility study intended of CO2 emission reduction, consisting of the modification plan of the SAN ANTONIO power plant, that is the plan to replace the over-aged gas turbines at the power plant. Its necessity has been identified. It was disclosed that the project has the effects of reducing CO2 of 82,000 tons annually, and the investment can be recovered in nine years. (NEDO)

  5. Feasibility study of patient motion monitoring using tactile array sensor

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Tae Ho; Kang, Seong Hee; Kim, Dong Su; Cho, Min Seok; Kim, Kyeong Hyeon; Suh, Tae Suk [Dept. of Biomedical Engineering, Research Institute of Biomedical Engineering, the Catholic University of Korea, Seoul (Korea, Republic of); Kim, Si Yong [Dept. of Radiation Oncology, Virginia Commonwealth University, Richmond (United States)

    2014-11-15

    The aim of this study is to evaluate patient pretreatment set-up error and intra-fraction motion using the tactile array sensors (Pressure Profile Systems Inc, Los Angeles, CA) which could measure distributed pressure profiles along the contacting surface and to check a feasibility of the sensor (tactile array sensor) in the patient motion monitoring. Laser alignment and optical camera based monitoring system are very useful for reduce patient set-up error but these systems could not monitor the blind area like patient's back position. Actually after patient alignment using laser or optical monitoring system, it was assumed that there is no error in the patient's back position (pressure profile distribution). But if an error occurs in the patient's back position, it will affect the radiation therapy accuracy. In spite of optical motion monitoring or using the immobilization tool, distributed pressure profiles of patient's back position was changed during inter and intra-fraction. For more accurate patient set-up, blind area (patient's back) monitoring was necessary. We expect that the proposed method will be very useful for make up for the weakness of optical monitoring method.

  6. Feasibility Study of 8-Bit Microcontroller Applications for Ethernet

    Directory of Open Access Journals (Sweden)

    Lech Gulbinovič

    2011-08-01

    Full Text Available Feasibility study of 8-bit microcontroller applications for Ethernet is presented. Designed device is based on ATmega32 microcontroller and 10 Mbps Ethernet controller ENC28J60. Device is simulated as mass queuing theoretical model with ticket booking counter. Practical explorations are accomplished and characteristics are determined. Practical results are compared to theoretical ones. Program code and device packet processing speed optimization are discussed. Microcontroller packet processing speed and packet latency depend on packet size. For ICMP protocol packet processing speed varies 1.4–2.1 Mbps, latency – 0.8–8.4 ms. UDP protocol packet processing speed varies 1.3–1.8 Mbps, latency – 1.1–9.6 ms. Packet processing speed depends on compilation settings and program code compression level. Best results are reached on optimization le­vel ‑O3, then speed increased ~3% but program code size increased 68% comparing to –Os optimization level.Article in Lithuanian

  7. Feasibility study of local ultrasound hyperthermia in cancer therapy

    International Nuclear Information System (INIS)

    Jones, K.G.; Straube, W.; Emami, B.; Perez, C.A.

    1987-01-01

    This paper describes a retrospective analysis of patients treated at Washington University for recurrent or persistent cancer with Ultrasound Hyperthermia between October 1984 and June 1986. Fifteen of 102 lesions were treated during this time period with Ultrasound Hyperthermia instead of microwave hyperthermia due to the size of the lesion needing heat at depths greater than 4 cm. Also, the patients' lesion could not be implanted for interstitial microwave hyperthermia. Fourteen of the treated patients received concomitant radiotherapy, while one received concomitant Bleomycin. There were 79 total hyperthermia treatments delivered, of which 67 achieved a therapeutic temperature of 43 0 C for 60 minutes. During 15/79 treatments, patients experienced pain; of which 11/15 lead to poor heating. Only one treatment of the twelve poor treatments was secondary to technical difficulties. Complete local control was accomplished in seven patients, a partial response in four patients. The results of therapeutic heating and its relationship to the site of treatment and local control are presented, along with phantom studies of Ultrasound microwave hyperthermia reemphasizing the feasibility of using Ultrasound Hyperthermia

  8. Moving with music for stroke rehabilitation: a sonification feasibility study.

    Science.gov (United States)

    Scholz, Daniel S; Rhode, Sönke; Großbach, Michael; Rollnik, Jens; Altenmüller, Eckart

    2015-03-01

    Gross-motor impairments are common after stroke, but efficacious and motivating therapies for these impairments are scarce. We present a novel musical sonification therapy especially designed to retrain gross-motor functions. Four stroke patients were included in a clinical pre-post feasibility study and were trained with our sonification training. Patients' upper-extremity functions and their psychological states were assessed before and after training. The four patients were subdivided into two groups, with both groups receiving 9 days of musical sonification therapy (music group, MG) or a sham sonification training (control group, CG). The only difference between these training protocols was that, in the CG, no sound was played back. During the training the patients initially explored the acoustic effects of their arm movements, and at the end of the training the patients played simple melodies by moving their arms. The two patients in the MG improved in nearly all motor function tests after the training. They also reported in the stroke impact scale, which assesses well-being, memory, thinking, and social participation, to be less impaired by the stroke. The two patients in the CG did benefit less from the movement training. Taken together, musical sonification may be a promising therapy for impairments after stroke. © 2015 New York Academy of Sciences.

  9. Identifying the educational needs of menopausal women: a feasibility study.

    Science.gov (United States)

    Trudeau, Kimberlee J; Ainscough, Jessica L; Trant, Meredith; Starker, Joan; Cousineau, Tara M

    2011-01-01

    The goal of this project was to identify the educational needs of menopausal women and test the feasibility of an online self management program based on social learning theory. The four stages included 1) a needs assessment using a) focus groups with 24 women ages 40 to 55 and b) phone interviews with eight health experts; 2) the use of concept mapping methodology for quantifying qualitative data from stage 1 to identify the core programmatic concepts; 3) development of a demonstration program; and 4) a pilot study with 35 women and 9 health experts to assess knowledge gained and program satisfaction. Results show that women desire more information about normalcy of menopause and symptom management and found the program to meet a need for menopausal education otherwise perceived as unavailable. The women significantly increased their menopausal knowledge after brief exposure (t(34) = 3.64; p = .001). This project provides support for an online health education program for menopausal women and content ideas for inclusion in women's health education curriculum. Copyright © 2011 Jacobs Institute of Women's Health. Published by Elsevier Inc. All rights reserved.

  10. Increasing fruits and vegetables in midlife women: a feasibility study.

    Science.gov (United States)

    Gunn, Caroline A; Weber, Janet L; Coad, Jane; Kruger, Marlena C

    2013-07-01

    The positive link between bone health and fruit/vegetable consumption has been attributed to the lower renal acid load of a diet high in alkaline-forming fruit/vegetables. Other important dietary determinants of bone health include micronutrients and bioactives found in fruit/vegetables. We hypothesized that increased intake of fruit/vegetables to 9 or more servings a day would lower net endogenous acid production (NEAP) significantly (~20 mEq/d) and increase urine pH (0.5 pH units). This 8-week feasibility study investigated if 21 midlife women (age, 40-65 years) currently consuming 5 or less servings a day of fruit/vegetables could increase their intake to 9 or more servings a day to substantially lower NEAP and include specific vegetables daily. Three-day diet diaries were completed at baseline and the end of the study and assessed for NEAP (estimated) and number of servings from all food groups. Urine pH dipsticks were provided for the participants to assess and record their fasting urine pH daily (second void). Seventy-six percent of women achieved the study aim, which was to increase to 9 or more servings of fruit/vegetables for at least 5 d/wk. There was a reduction in the number of bread/cereal servings. Net endogenous acid production (estimated) was reduced significantly, with a mean urine pH increase of 0.68 pH units (95% confidence interval, 0.46-1.14); however, daily urine pH measures showed high variability. This study demonstrated that a group of midlife women can change their diet for 8 weeks by significantly increasing fruit/vegetable servings and include specific "bone friendly" vegetables daily, resulting in a significant decrease in estimated dietary NEAP and an increase in urine pH. Copyright © 2013 Elsevier Inc. All rights reserved.

  11. Feasibility of protein turnover studies in prototroph Saccharomyces cerevisiae strains.

    Science.gov (United States)

    Martin-Perez, Miguel; Villén, Judit

    2015-04-07

    Quantitative proteomics studies of yeast that use metabolic labeling with amino acids rely on auxotrophic mutations of one or more genes on the amino acid biosynthesis pathways. These mutations affect yeast metabolism and preclude the study of some biological processes. Overcoming this limitation, it has recently been described that proteins in a yeast prototrophic strain can also be metabolically labeled with heavy amino acids. However, the temporal profiles of label incorporation under the different phases of the prototroph's growth have not been examined. Labeling trajectories are important in the study of protein turnover and dynamics, in which label incorporation into proteins is monitored across many time points. Here we monitored protein labeling trajectories for 48 h after a pulse with heavy lysine in a yeast prototrophic strain and compared them with those of a lysine auxotrophic yeast. Labeling was successful in prototroph yeast during exponential growth phase but not in stationary phase. Furthermore, we were able to determine the half-lives of more than 1700 proteins during exponential phase of growth with high accuracy and reproducibility. We found a median half-life of 2 h in both strains, which corresponds with the cellular doubling time. Nucleolar and ribosomal proteins showed short half-lives, whereas mitochondrial proteins and other energy production enzymes presented longer half-lives. Except for some proteins involved in lysine biosynthesis, we observed a high correlation in protein half-lives between prototroph and auxotroph strains. Overall, our results demonstrate the feasibility of using prototrophs for proteomic turnover studies and provide a reliable data set of protein half-lives in exponentially growing yeast.

  12. Feasibility study on the development of advanced LWR fuel technology

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Youn Ho; Sohn, D. S.; Jeong, Y. H.; Song, K. W.; Song, K. N.; Chun, T. H.; Bang, J. G.; Bae, K. K.; Kim, D. H. and others

    1997-07-01

    Worldwide R and D trends related to core technology of LWR fuels and status of patents have been surveyed for the feasibility study. In addition, various fuel cycle schemes have been studied to establish the target performance parameters. For the development of cladding material, establishment of long-term research plan for alloy development and optimization of melting process and manufacturing technology were conducted. A work which could characterize the effect of sintering additives on the microstructure of UO{sub 2} pellet has been experimentally undertaken, and major sintering variables and their ranges have been found in the sintering process of UO{sub 2}-Gd{sub 2}O{sub 3} burnable absorber pellet. The analysis of state of the art technology related to flow mixing device for spacer grid and debris filtering device for bottom nozzle and the investigation of the physical phenomena related to CHF enhancement and the establishment of the data base for thermal-hydraulic performance tests has been done in this study. In addition, survey on the documents of the up-to-date PWR fuel assemblies developed by foreign vendors have been carried out to understand their R and D trends and establish the direction of R and D for these structural components. And, to set the performance target of the new fuel, to be developed, fuel burnup and economy under the extended fuel cycle length scheme were estimated. A preliminary study on the failure mechanism of CANDU fuel, key technology and advanced coating has been performed. (author). 190 refs., 31 tabs., 129 figs.

  13. Stroke Experiences in Weblogs: A Feasibility Study of Sex Differences

    Science.gov (United States)

    Koh, Sukjin; Gordon, Andrew S; Wienberg, Christopher; Sood, Sara O; Morley, Stephanie

    2014-01-01

    Background Research on cerebral stroke symptoms using hospital records has reported that women experience more nontraditional symptoms of stroke (eg, mental status change, pain) than men do. This is an important issue because nontraditional symptoms may delay the decision to get medical assistance and increase the difficulty of correct diagnosis. In the present study, we investigate sex differences in the stroke experience as described in stories on weblogs. Objective The goal of this study was to investigate the feasibility of using the Internet as a source of data for basic research on stroke experiences. Methods Stroke experiences described in blogs were identified by using StoryUpgrade, a program that searches blog posts using a fictional prototype story. In this study, the prototype story was a description of a stroke experience. Retrieved stories coded by the researchers as relevant were used to update the search query and retrieve more stories using relevance feedback. Stories were coded for first- or third-person narrator, traditional and nontraditional patient symptoms, type of stroke, patient sex and age, delay before seeking medical assistance, and delay at hospital and in treatment. Results There were 191 relevant stroke stories of which 174 stories reported symptoms (52.3% female and 47.7% male patients). There were no sex differences for each traditional or nontraditional stroke symptom by chi-square analysis (all Ps>.05). Type of narrator, however, affected report of traditional and nontraditional symptoms. Female first-person narrators (ie, the patient) were more likely to report mental status change (56.3%, 27/48) than male first-person narrators (36.4%, 16/44), a marginally significant effect by logistic regression (P=.056), whereas reports of third-person narrators did not differ for women (27.9%, 12/43) and men (28.2%, 11/39) patients. There were more reports of at least 1 nontraditional symptom in the 92 first-person reports (44.6%, 41/92) than

  14. Stroke experiences in weblogs: a feasibility study of sex differences.

    Science.gov (United States)

    Koh, Sukjin; Gordon, Andrew S; Wienberg, Christopher; Sood, Sara O; Morley, Stephanie; Burke, Deborah M

    2014-03-19

    Research on cerebral stroke symptoms using hospital records has reported that women experience more nontraditional symptoms of stroke (eg, mental status change, pain) than men do. This is an important issue because nontraditional symptoms may delay the decision to get medical assistance and increase the difficulty of correct diagnosis. In the present study, we investigate sex differences in the stroke experience as described in stories on weblogs. The goal of this study was to investigate the feasibility of using the Internet as a source of data for basic research on stroke experiences. Stroke experiences described in blogs were identified by using StoryUpgrade, a program that searches blog posts using a fictional prototype story. In this study, the prototype story was a description of a stroke experience. Retrieved stories coded by the researchers as relevant were used to update the search query and retrieve more stories using relevance feedback. Stories were coded for first- or third-person narrator, traditional and nontraditional patient symptoms, type of stroke, patient sex and age, delay before seeking medical assistance, and delay at hospital and in treatment. There were 191 relevant stroke stories of which 174 stories reported symptoms (52.3% female and 47.7% male patients). There were no sex differences for each traditional or nontraditional stroke symptom by chi-square analysis (all Ps>.05). Type of narrator, however, affected report of traditional and nontraditional symptoms. Female first-person narrators (ie, the patient) were more likely to report mental status change (56.3%, 27/48) than male first-person narrators (36.4%, 16/44), a marginally significant effect by logistic regression (P=.056), whereas reports of third-person narrators did not differ for women (27.9%, 12/43) and men (28.2%, 11/39) patients. There were more reports of at least 1 nontraditional symptom in the 92 first-person reports (44.6%, 41/92) than in the 82 third-person reports (25

  15. Feasibility of the Dutch ICF Activity Inventory: a pilot study

    Directory of Open Access Journals (Sweden)

    van Nispen Ruth MA

    2010-11-01

    Full Text Available Abstract Background Demographic ageing will lead to increasing pressure on visual rehabilitation services, which need to be efficiently organised in the near future. The Dutch ICF Activity Inventory (D-AI was developed to assess the rehabilitation needs of visually impaired persons. This pilot study tests the feasibility of the D-AI using a computer-assisted telephone interview. Methods In addition to the regular intake, the first version of the D-AI was assessed in 20 patients. Subsequently, patients and intake assessors were asked to fill in an evaluation form. Based on these evaluations, a new version of the D-AI was developed. Results Mean administration time of the D-AI was 88.8 (± 41.0 minutes. Overall, patients and assessors were positive about the D-AI assessment. However, professionals and 60% of the patients found the administration time to be too long. All included items were considered relevant and only minor adjustments were recommended. Conclusion The systematic character of the revised D-AI will prevent topics from being overlooked and indicate which needs have the highest priority from a patient-centred perspective. Moreover, ongoing assessment of the D-AI will enhance evaluation of the rehabilitation process. To decrease administration time, in the revised D-AI only the top priority goals will be fully assessed. Using the D-AI, a rehabilitation plan based on individual needs can be developed for each patient. Moreover, it enables better evaluation of the effects of rehabilitation. A larger validation study is planned.

  16. Pueblo of Jemez Geothermal Feasibility Study Fianl Report

    Energy Technology Data Exchange (ETDEWEB)

    S.A. Kelley; N. Rogers; S. Sandberg; J. Witcher; J. Whittier

    2005-03-31

    This project assessed the feasibility of developing geothermal energy on the Pueblo of Jemez, with particular attention to the Red Rocks area. Geologic mapping of the Red Rocks area was done at a scale of 1:6000 and geophysical surveys identified a potential drilling target at a depth of 420 feet. The most feasible business identified to use geothermal energy on the reservation was a greenhouse growing culinary and medicinal herbs. Space heating and a spa were identified as two other likely uses of geothermal energy at Jemez Pueblo. Further geophysical surveys are needed to identify the depth to the Madera Limestone, the most likely host for a major geothermal reservoir.

  17. Feasibility study of a level gauge using cosmic-rays

    International Nuclear Information System (INIS)

    Matsuda, Hideharu; Fukaya, Mitsuharu; Minato, Susumu

    1989-01-01

    Cosmic-ray intensities were measured at the stairs in a subway station in Nagoya City, inside a tall concrete building and under a cylindrical water tank to examine the feasibility of a cosmic-ray level gauge using a scintillation counter. The measured results agreed quite well with theoretical calculations. The maximum distinguishable water depth was evaluated to be approximately the radius of the tank from the results of many systematic calculations. It was found from these results that the practical application of a cosmic-ray level gauge is feasible. (author)

  18. Feasibility Study for Renewable Energy Development on Tribal Lands

    Energy Technology Data Exchange (ETDEWEB)

    John Hendrix, Project Director; Charles Weir, Project Manager; Dr. John Plodinec, Technology Advisor; Dr. Steve Murray, Economic Advisor

    2005-07-21

    Project Objective: The Mississippi Band of Choctaw Indians (MBCI) conducted a study of the feasibility of siting a renewable energy biomass-based installation on tribal lands. The purpose of the study was to determine whether such an installation can be economically sustainable, as well as consistent with the cultural, social, and economic goals of the Tribe. Scope: To achieve the goal of the feasibility study, the following tasks were carried out: (1) Resource availability assessment--The objective of this assessment was to determine the availability of both poultry litter and wood residues for use in the proposed facility. (2) Power utilization assessment--The objective of this assessment was to determine the potential market size for power produced, the existing infrastructure for delivering power to that market, and the costs and economic returns for doing so. (3) Technology review--The objective of this review was to identify one, or more, technical options for detailed economic and technical assessment. The study considered a range of feedstock and product mixtures of poultry litter; wood residues as feedstock; and electrical power and other ancillary products as outputs. Distributed power sources was also examined. Technologies ranging from gasification to systems that produce both power and value-added chemicals were considered. Technologies selected for detailed review were those that can be sized to process the amount of available feed (poultry litter, or poultry litter and wood residues), and that also appear to make economic sense in terms of the value of their inputs. The technology review leaned heavily on the experience from similar prior DOE projects, particularly those conducted by the National Renewable Energy Laboratory (NREL). NREL was involved in a consultative role, so that the project team could leverage their experience. (4) Systems Design(s)--Based on the technology review, a pre-conceptual design for an installation was developed. This

  19. Preliminary feasibility study of the heat - pipe ENHS reactor

    International Nuclear Information System (INIS)

    Fratoni, M.; Kim, L.; Mattafirri, S.; Petroski, R.; Greenspan, E.

    2007-01-01

    This preliminary study assesses the feasibility of designing an Encapsulated Nuclear Heat Source (ENHS) reactor [1] to have a solid core from which heat is removed by liquid-metal heat pipes (HP). Like the SAFE space nuclear reactor core [2], the HP-ENHS core is comprised of fuel rods and HPs embedded in a solid structure arranged in a hexagonal lattice in a 3:1 ratio. The HPs extend beyond the core length and transfer heat to a secondary coolant that flows by natural circulation. The HP-ENHS reactor is designed to preserve many features of the ENHS reactor including 20-year operation without refueling, very small excess reactivity throughout life, natural circulation cooling, walk-away passive safety, and robust proliferation resistance. The target power level and specific power of the HP-ENHS reactor are those of the reference ENHS reactor [1]. Compared to previous ENHS reactor designs utilizing a lead or lead-bismuth alloy natural circulation cooling system, the HP-ENHS reactor offers a number of possible advantageous features including: (1) significantly enhanced decay heat removal capability; (2) no positive void reactivity coefficients; (3) no direct contact between the fuel clad and coolant, hence, relatively lower wet corrosion of the clad; (4) a core that is more robust for transportation; (5) higher temperature potentially offering higher efficiency and hydrogen production capability. The study focuses on four areas: material compatibility analysis, HP performance analysis, neutronic analysis and thermal-hydraulic analysis. Of four high-temperature structural materials evaluated, Mo TZM alloy is the preferred choice; its upper estimated feasible operating temperature is 1350 K. HP performance is evaluated as a function of working fluid type, operating temperature, wick design and HP diameter and length. Sodium is the preferred working fluid and the HP working temperature is 1300 K. The neutronic analysis found that it is possible to achieve criticality

  20. Dual resolution cone beam breast CT: A feasibility study

    International Nuclear Information System (INIS)

    Chen Lingyun; Shen Youtao; Lai, Chao-Jen; Han Tao; Zhong Yuncheng; Ge Shuaiping; Liu Xinming; Wang Tianpeng; Yang, Wei T.; Whitman, Gary J.; Shaw, Chris C.

    2009-01-01

    Purpose: In this study, the authors investigated the feasibility of a dual resolution volume-of-interest (VOI) cone beam breast CT technique and compared two implementation approaches in terms of dose saving and scatter reduction. Methods: With this technique, a lead VOI mask with an opening is inserted between the x-ray source and the breast to deliver x-ray exposure to the VOI while blocking x rays outside the VOI. A CCD detector is used to collect the high resolution projection data of the VOI. Low resolution cone beam CT (CBCT) images of the entire breast, acquired with a flat panel (FP) detector, were used to calculate the projection data outside the VOI with the ray-tracing reprojection method. The Feldkamp-Davis-Kress filtered backprojection algorithm was used to reconstruct the dual resolution 3D images. Breast phantoms with 180 μm and smaller microcalcifications (MCs) were imaged with both FP and FP-CCD dual resolution CBCT systems, respectively. Two approaches of implementing the dual resolution technique, breast-centered approach and VOI-centered approach, were investigated and evaluated for dose saving and scatter reduction with Monte Carlo simulation using a GEANT4 package. Results: The results showed that the breast-centered approach saved more breast absorbed dose than did VOI-centered approach with similar scatter reduction. The MCs in fatty breast phantom, which were invisible with FP CBCT scan, became visible with the FP-CCD dual resolution CBCT scan. Conclusions: These results indicate potential improvement of the image quality inside the VOI with reduced breast dose both inside and outside the VOI.

  1. Feasibility study report for the 200-BP-1 operable unit

    International Nuclear Information System (INIS)

    1993-06-01

    This feasibility study examines a range of alternatives and provides recommendations for selecting a preferred alternative for remediating contamination at the 200-BP-1 operable unit. The 200-BP-1 operable unit is located in the center of the Hanford Site along the northern boundary of the 200 East Area. The 241-BY Tank Farm is located immediately to the south of the operable unit. 200-BP-1 is a source operable unit with contaminated soils associated primarily with nine inactive cribs (known as the 216-B cribs). These cribs were used for disposal of low-level radioactive liquid waste from U Plant uranium recovery operations, and waste storage tank condensate from the adjacent 241-BY Tank Farm. The cribs used for disposal of U Plant waste were in operation from 1955--1965, and the cribs used for disposal of tank condensate were in operation from 1965--1975. In addition to the cribs, four unplanned releases of radioactive materials have occurred within the operable unit. Contaminated surface soils associated with the unplanned releases have been consolidated over the cribs and covered with clean soil to reduce contaminant migration and exposure. Discharge of wastes to the cribs has resulted in soil and groundwater contamination. The groundwater is being addressed as part of the 200 East Aggregate Area, groundwater operable unit. Contaminated soils at the site can be categorized by the types of contaminants, their distribution in the soil column, and the risk posed by the various potential exposure pathways. Below the clean soil cover, the near surface soils contain low-levels of contamination with cesium-137, radium-226, strontium-90, thorium-228, and uranium. The lifetime incremental cancer risk associated with these soils if they were exposed at the surface is 9x10 -5

  2. Feasibility study report for the 200-BP-1 operable unit

    International Nuclear Information System (INIS)

    1994-01-01

    This feasibility study (FS) examines a range of alternatives and provides recommendations for selecting a preferred altemative for remediating contamination at the 200-BP-1 operable unit. The 200-BP-1 operable unit is located in the center of the Hanford Site along the northern boundary of the 200 East Area. The 241-BY Tank Farm is located immediately to the south of the operable unit. 200-BP-1 is a source operable unit with contaminated soils associated primarily with nine inactive cribs (known as the 216-B cribs). These cribs were used for disposal of low-level radioactive liquid waste from U Plant uranium recovery operations, and waste storage tank condensate from the adjacent 241-BY Tank Farm. The cribs used for disposal of U Plant waste were in operation from 1955--1965, and the cribs used for disposal of tank condensate were in operation from 1965-1975. In addition to the cribs, four unplanned releases of radioactive materials have occurred within the operable unit. Contaminated surface soils associated with the unplanned releases have been consolidated over the cribs and covered with clean soil to reduce contaminant migration and exposure. Discharge of wastes to the cribs has resulted in soil and groundwater contamination. The groundwater is being addressed as part of the 200 East Aggregate Area groundwater operable unit. Contaminated soils at the site can be categorized by the types of contaminants, their distribution in the soil column, and the risk posed by the various potential exposure pathways. Below the clean soil cover, the near surface soils contain low-:levels of contamination with cesium-137, radium-226, strontium-90, thorium-228 and uranium. The lifetime incremental cancer risk associated with these soils if they were exposed at the surface is 9 x 10 5

  3. Feasibility study report for the 200-BP-1 operable unit

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-01

    This feasibility study examines a range of alternatives and provides recommendations for selecting a preferred alternative for remediating contamination at the 200-BP-1 operable unit. The 200-BP-1 operable unit is located in the center of the Hanford Site along the northern boundary of the 200 East Area. The 241-BY Tank Farm is located immediately to the south of the operable unit. 200-BP-1 is a source operable unit with contaminated soils associated primarily with nine inactive cribs (known as the 216-B cribs). These cribs were used for disposal of low-level radioactive liquid waste from U Plant uranium recovery operations, and waste storage tank condensate from the adjacent 241-BY Tank Farm. The cribs used for disposal of U Plant waste were in operation from 1955--1965, and the cribs used for disposal of tank condensate were in operation from 1965--1975. In addition to the cribs, four unplanned releases of radioactive materials have occurred within the operable unit. Contaminated surface soils associated with the unplanned releases have been consolidated over the cribs and covered with clean soil to reduce contaminant migration and exposure. Discharge of wastes to the cribs has resulted in soil and groundwater contamination. The groundwater is being addressed as part of the 200 East Aggregate Area, groundwater operable unit. Contaminated soils at the site can be categorized by the types of contaminants, their distribution in the soil column, and the risk posed by the various potential exposure pathways. Below the clean soil cover, the near surface soils contain low-levels of contamination with cesium-137, radium-226, strontium-90, thorium-228, and uranium. The lifetime incremental cancer risk associated with these soils if they were exposed at the surface is 9{times}10{sup {minus}5}.

  4. Automated estimation of hip prosthesis migration: a feasibility study

    Science.gov (United States)

    Vandemeulebroucke, Jef; Deklerck, Rudi; Temmermans, Frederik; Van Gompel, Gert; Buls, Nico; Scheerlinck, Thierry; de Mey, Johan

    2013-09-01

    A common complication associated with hip arthoplasty is prosthesis migration, and for most cemented components a migration greater than 0.85 mm within the first six months after surgery, are an indicator for prosthesis failure. Currently, prosthesis migration is evaluated using X-ray images, which can only reliably estimate migrations larger than 5 mm. We propose an automated method for estimating prosthesis migration more accurately, using CT images and image registration techniques. We report on the results obtained using an experimental set-up, in which a metal prosthesis can be translated and rotated with respect to a cadaver femur, over distances and angles applied using a combination of positioning stages. Images are first preprocessed to reduce artefacts. Bone and prosthesis are extracted using consecutive thresholding and morphological operations. Two registrations are performed, one aligning the bones and the other aligning the prostheses. The migration is estimated as the difference between the found transformations. We use a robust, multi-resolution, stochastic optimization approach, and compare the mean squared intensity differences (MS) to mutual information (MI). 30 high-resolution helical CT scans were acquired for prosthesis translations ranging from 0.05 mm to 4 mm, and rotations ranging from 0.3° to 3° . For the translations, the mean 3D registration error was found to be 0.22 mm for MS, and 0.15 mm for MI. For the rotations, the standard deviation of the estimation error was 0.18° for MS, and 0.08° for MI. The results show that the proposed approach is feasible and that clinically acceptable accuracies can be obtained. Clinical validation studies on patient images will now be undertaken.

  5. NVN 5694 intra laboratory validation. Feasibility study for interlaboratory- validation

    International Nuclear Information System (INIS)

    Voors, P.I.; Baard, J.H.

    1998-11-01

    Within the project NORMSTAR 2 a number of Dutch prenormative protocols have been defined for radioactivity measurements. Some of these protocols, e.g. the Dutch prenormative protocol NVN 5694, titled Methods for radiochemical determination of polonium-210 and lead-210, have not been validated, neither by intralaboratory nor interlaboratory studies. Validation studies are conducted within the framework of the programme 'Normalisatie and Validatie van Milieumethoden 1993-1997' (Standardization and Validation of test methods for environmental parameters) of the Dutch Ministry of Housing, Physical Planning and the Environment (VROM). The aims of this study were (a) a critical evaluation of the protocol, (b) investigation on the feasibility of an interlaboratory study, and (c) the interlaboratory validation of NVN 5694. The evaluation of the protocol resulted in a list of deficiencies varying from missing references to incorrect formulae. From the survey by interview it appeared that for each type of material, there are 4 to 7 laboratories willing to participate in a interlaboratory validation study. This reflects the situation in 1997. Consequently, if 4 or 6 (the minimal number) laboratories are participating and each laboratory analyses 3 subsamples, the uncertainty in the repeatability standard deviation is 49 or 40 %, respectively. If the ratio of reproducibility standard deviation to the repeatability standard deviation is equal to 1 or 2, then the uncertainty in the reproducibility standard deviation increases from 42 to 67 % and from 34 to 52 % for 4 or 6 laboratories, respectively. The intralaboratory validation was established on four different types of materials. Three types of materials (milkpowder condensate and filter) were prepared in the laboratory using the raw material and certified Pb-210 solutions, and one (sediment) was obtained from the IAEA. The ECN-prepared reference materials were used after testing on homogeneity. The pre-normative protocol can

  6. Objectivist case study research

    DEFF Research Database (Denmark)

    Ridder, Hanne Mette Ochsner; Fachner, Jörg

    2016-01-01

    be achieved through the use of objectivist case study research. The strength of the case study design is that it allows for uncovering or suggesting causal relationships in real-life settings through an intensive and rich collection of data. According to Hilliard (1993), the opposite applies for extensive......In order to comprehend the impact of music therapy or music therapy processes, a researcher might look for an approach where the topic under investigation can be understood within a broader context. This calls for a rich inclusion of data and consequently a limited number of participants and may...... designs, in which a small amount of data is gathered on a large number of subjects. With the richness of data, the intensive design is ―the primary pragmatic reason for engaging in single-case or small N research‖ (p. 374) and for working from an idiographic rather than a nomothetic perspective....

  7. Feasibility study for adapting ITREC plant to reprocessing LMFBR fuels

    International Nuclear Information System (INIS)

    Moccia, A.; Rolandi, G.

    1976-05-01

    The report evaluates the feasibility of adapting ITREC plant to the reprocessing LMFBR fuels, with the double purpose of: 1) recovering valuable Pu contained in these fuels and recycling it to the fabrication plant; 2) trying, on a pilot scale, the chemical process technology to be applied in a future industrial plant for reprocessing the fuel elements discharged from fast breeder power reactors

  8. Final Report - Wind and Hydro Energy Feasibility Study - June 2011

    Energy Technology Data Exchange (ETDEWEB)

    Jim Zoellick; Richard Engel; Rubin Garcia; Colin Sheppard

    2011-06-17

    This feasibility examined two of the Yurok Tribe's most promising renewable energy resources, wind and hydro, to provide the Tribe detailed, site specific information that will result in a comprehensive business plan sufficient to implement a favorable renewable energy project.

  9. Livingston Parish Landfill Methane Recovery Project (Feasibility Study)

    Energy Technology Data Exchange (ETDEWEB)

    White, Steven

    2012-11-15

    The Woodside Landfill is owned by Livingston Parish, Louisiana and is operated under contract by Waste Management of Louisiana LLC. This public owner/private operator partnership is commonplace in the solid waste industry today. The landfill has been in operation since approximately 1988 and has a permitted capacity of approximately 41 million cubic yards. Based on an assumed in-place waste density of 0.94 ton per cubic yard, the landfill could have an expected design capacity of 39.3 million tons. The landfill does have an active landfill gas collection and control system (LFGCCS) in place because it meets the minimum thresholds for the New Source Performance Standards (NSPS). The initial LFGCS was installed prior to 2006 and subsequent phases were installed in 2007 and 2010. The Parish received a grant from the United States Department of Energy in 2009 to evaluate the potential for landfill gas recovery and utilization at the Woodside Landfill. This includes a technical and economic feasibility study of a project to install a landfill gas to energy (LFGTE) plant and to compare alternative technologies. The LFGTE plant can take the form of on-site electrical generation, a direct use/medium Btu option, or a high-Btu upgrade technology. The technical evaluation in Section 2 of this report concludes that landfill gas from the Woodside landfill is suitable for recovery and utilization. The financial evaluations in sections 3, 4, and 5 of this report provide financial estimates of the returns for various utilization technologies. The report concludes that the most economically viable project is the Electricity Generation option, subject to the Parish’s ability and willingness to allocate adequate cash for initial capital and/or to obtain debt financing. However, even this option does not present a solid return: by our estimates, there is a 19 year simple payback on the electricity generation option. All of the energy recovery options discussed in this report

  10. Feasibility Study on: Reforestation of Degraded Grasslands in Indonesia as a Climate Change Mitigation Option

    Energy Technology Data Exchange (ETDEWEB)

    Dalfelt, A; Naess, L O; Sutamihardja, R T.M.; Gintings, N

    1997-12-31

    The report deals with a cooperation project between Norway and Indonesia dealing with a feasibility study on sustainable reforestation of degraded grasslands in Indonesia. Poor forest management and uncontrolled land use changes contribute a significant share anthropogenic emissions of greenhouse gases, especially CO{sub 2}, and one of many ways to reduce the CO{sub 2} emission is to encourage reforestation and better forest management. The report contains a brief overview of the issue of Imperata (alang-alang) grasslands, an outline of the present status, a discussion of potential costs and benefits associated with reforestation, and suggestions of strategies which could be applied to reach the desired goals. Case studies are presented from three locations where field work has been undertaken. The case studies provide baseline data about the sites and the imperata grasslands, experiences from earlier efforts to rehabilitate the grasslands, the common attitude to reforestation among the local communities, a discussion of the feasibility of reforestation, and finally, recommendations for the future. 142 refs., 11 figs., 15 tabs.

  11. Feasibility Study on: Reforestation of Degraded Grasslands in Indonesia as a Climate Change Mitigation Option

    Energy Technology Data Exchange (ETDEWEB)

    Dalfelt, A.; Naess, L.O.; Sutamihardja, R.T.M.; Gintings, N.

    1996-12-31

    The report deals with a cooperation project between Norway and Indonesia dealing with a feasibility study on sustainable reforestation of degraded grasslands in Indonesia. Poor forest management and uncontrolled land use changes contribute a significant share anthropogenic emissions of greenhouse gases, especially CO{sub 2}, and one of many ways to reduce the CO{sub 2} emission is to encourage reforestation and better forest management. The report contains a brief overview of the issue of Imperata (alang-alang) grasslands, an outline of the present status, a discussion of potential costs and benefits associated with reforestation, and suggestions of strategies which could be applied to reach the desired goals. Case studies are presented from three locations where field work has been undertaken. The case studies provide baseline data about the sites and the imperata grasslands, experiences from earlier efforts to rehabilitate the grasslands, the common attitude to reforestation among the local communities, a discussion of the feasibility of reforestation, and finally, recommendations for the future. 142 refs., 11 figs., 15 tabs.

  12. Feasibility study for Boardman River hydroelectric power. Final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-02-22

    The feasibility of generating additional hydroelectric power from five consecutive existing dams located on the Boardman River in Grand Traverse County and Traverse City, Michigan, was investigated. The potential hydropower production capabilities, in terms of base load power and peak load power, the legal-institutional-environmental constraints, and the economic feasibility, including capital investment, operating costs and maintenance costs, were evaluated for each of the five dam sites individually and as a series of co-dependent facilities. The impact of installing fish passages at each site was analyzed separately. The feasibility assessment utilized the present worth analytical method, considering revenue based on thirty mills/kWh for power, 0.4% general economy escalation rate, and a 6% net income to the municipal utility. The sensitivity of fuel costs increasing at a different rate than the general price-escalation was tested by allowing the increase in fuel costs to vary from 3 to 8% per year. Assuming fuel costs increase at the same rate as the general economy, it is feasible to update, retrofit, renovate, and install hydroelectric generating capacity at Sabin, Boardman and Brown Bridge. Rehabilitation of Union Street and Keystone is also feasible but somewhat less attractive. Operating the dams as a co-dependent system has environmental advantages and can provide additional revenue through peak load power rates. A development plan to implement the above is outlined utilizing an ownership arrangement whereby Grand Traverse County provides easements for Sabin and Boardman Dams. The plan calls for operation of the system by Traverse City.

  13. Case Studies - Cervical Cancer

    Centers for Disease Control (CDC) Podcasts

    Dr. Alan Waxman, a professor of obstetrics and gynecology at the University of New Mexico and chair of the American College of Obstetricians and Gynecologists (ACOG) committee for the underserved, talks about several case studies for cervical cancer screening and management.

  14. Nuclear forensics case studies

    International Nuclear Information System (INIS)

    Fedchenko, Vitaly

    2016-01-01

    The objective of this presentation is to share three case studies from the Institute of Transuranium Elements (ITU) which describe the application of nuclear forensics to events where nuclear and other radioactive material was found to be out of regulatory control

  15. SCA12 case study

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Genetics; Volume 88; Issue 1. Utilizing linkage disequilibrium information from Indian Genome Variation Database for mapping mutations: SCA12 case study. Samira Bahl Ikhlak Ahmed The Indian Genome Variation Consortium Mitali Mukerji. Research Article Volume 88 Issue 1 April 2009 pp 55- ...

  16. national Case study

    African Journals Online (AJOL)

    This national case study reports on the development of a national network, ... system under the new policy), tends to be limited by content on problems and ... 20 credit programme; and within two Post Graduate Certificate of Education contexts, ...... descriptive with an issues focus (empirical) towards awareness production to.

  17. MRI case studies

    International Nuclear Information System (INIS)

    Huggett, S.; Barber, J.

    1989-01-01

    Three case studies are presented to show the value of magnetic resonance imaging used in conjunction with other imaging techniques. In each case MRI proved a vital diagnostic tool and superior to CT in showing firstly the haematoma in a patient with aphasia and right-sided weakness, secondly the size of the disc herniation in a patient with severe leg and ankle pains and thirdly the existence of a metastatic lesion in a patient with a previous history of breast cancer. 11 figs

  18. Cherenkov luminescence measurements with digital silicon photomultipliers: a feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Ciarrocchi, Esther; Belcari, Nicola; Guerra, Alberto Del [Department of Physics, University of Pisa, Pisa (Italy); INFN, section of Pisa, Pisa (Italy); Cherry, Simon R. [Department of Biomedical Engineering, University of California, Davis, CA (United States); Lehnert, Adrienne; Hunter, William C. J.; McDougald, Wendy; Miyaoka, Robert S.; Kinahan, Paul E. [Department of Radiology, University of Washington, Seattle, WA (United States)

    2015-11-16

    A feasibility study was done to assess the capability of digital silicon photomultipliers to measure the Cherenkov luminescence emitted by a β source. Cherenkov luminescence imaging (CLI) is possible with a charge coupled device (CCD) based technology, but a stand-alone technique for quantitative activity measurements based on Cherenkov luminescence has not yet been developed. Silicon photomultipliers (SiPMs) are photon counting devices with a fast impulse response and can potentially be used to quantify β-emitting radiotracer distributions by CLI. In this study, a Philips digital photon counting (PDPC) silicon photomultiplier detector was evaluated for measuring Cherenkov luminescence. The PDPC detector is a matrix of avalanche photodiodes, which were read one at a time in a dark count map (DCM) measurement mode (much like a CCD). This reduces the device active area but allows the information from a single avalanche photodiode to be preserved, which is not possible with analog SiPMs. An algorithm to reject the noisiest photodiodes and to correct the measured count rate for the dark current was developed. The results show that, in DCM mode and at (10–13) °C, the PDPC has a dynamic response to different levels of Cherenkov luminescence emitted by a β source and transmitted through an opaque medium. This suggests the potential for this approach to provide quantitative activity measurements. Interestingly, the potential use of the PDPC in DCM mode for direct imaging of Cherenkov luminescence, as a opposed to a scalar measurement device, was also apparent. We showed that a PDPC tile in DCM mode is able to detect and image a β source through its Cherenkov radiation emission. The detector’s dynamic response to different levels of radiation suggests its potential quantitative capabilities, and the DCM mode allows imaging with a better spatial resolution than the conventional event-triggered mode. Finally, the same acquisition procedure and data processing could

  19. Cherenkov luminescence measurements with digital silicon photomultipliers: a feasibility study

    International Nuclear Information System (INIS)

    Ciarrocchi, Esther; Belcari, Nicola; Guerra, Alberto Del; Cherry, Simon R.; Lehnert, Adrienne; Hunter, William C. J.; McDougald, Wendy; Miyaoka, Robert S.; Kinahan, Paul E.

    2015-01-01

    A feasibility study was done to assess the capability of digital silicon photomultipliers to measure the Cherenkov luminescence emitted by a β source. Cherenkov luminescence imaging (CLI) is possible with a charge coupled device (CCD) based technology, but a stand-alone technique for quantitative activity measurements based on Cherenkov luminescence has not yet been developed. Silicon photomultipliers (SiPMs) are photon counting devices with a fast impulse response and can potentially be used to quantify β-emitting radiotracer distributions by CLI. In this study, a Philips digital photon counting (PDPC) silicon photomultiplier detector was evaluated for measuring Cherenkov luminescence. The PDPC detector is a matrix of avalanche photodiodes, which were read one at a time in a dark count map (DCM) measurement mode (much like a CCD). This reduces the device active area but allows the information from a single avalanche photodiode to be preserved, which is not possible with analog SiPMs. An algorithm to reject the noisiest photodiodes and to correct the measured count rate for the dark current was developed. The results show that, in DCM mode and at (10–13) °C, the PDPC has a dynamic response to different levels of Cherenkov luminescence emitted by a β source and transmitted through an opaque medium. This suggests the potential for this approach to provide quantitative activity measurements. Interestingly, the potential use of the PDPC in DCM mode for direct imaging of Cherenkov luminescence, as a opposed to a scalar measurement device, was also apparent. We showed that a PDPC tile in DCM mode is able to detect and image a β source through its Cherenkov radiation emission. The detector’s dynamic response to different levels of radiation suggests its potential quantitative capabilities, and the DCM mode allows imaging with a better spatial resolution than the conventional event-triggered mode. Finally, the same acquisition procedure and data processing could

  20. Feasibility study on the introduction of hybrid buses; Hybrid bus donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose of this research is to design pilot projects for introducing hybrid buses into the public transportation sector. This research also covers contents regarding hybrid buses with a trolley-collector motor and a diesel engine, to identify technical and economical problems and to analyze cost beneficiation using hybrid buses. The trolley parallel hybrid system has been employed for the feasibility study. This system has abundant operation results in Europe and the USA. Its battery is small or is not necessary, and the maintenance cost is also low. As a result of the feasibility study, reduction effects of CO2 emission were found out. When the CO2 generation at the power plant is not counted, the reduction effect was estimated to be 32% compared with the CO2 emission from diesel buses. When the CO2 generation at the power plant is considered, it was estimated to be 18%. The cost beneficiation was investigated for the cases of the transportations using trolley system surrounding a medium-scale terminal among large-scale housing development, tourist resort, and stations. The annual income is estimated to be larger than the annual payment in each case. It was found that the hybrid bus is economically established. 17 refs., 48 figs., 41 tabs.

  1. A neutronic feasibility study for LEU conversion of the WWR-M reactor at Gatchina

    International Nuclear Information System (INIS)

    Petrov, Yu. V.; Erykalov, A.N.; Onegin, M.S.

    2000-01-01

    In this report we present the results of computations of the full scale reactor core with HEU (90%), MEU (36%) and LEU (19.75%) fuel. The reactor computer model for the MCU RFFI Monte Carlo code includes all peculiarities of the core. Calculations show that a uranium density of 3.3gU/cm 3 of MEU (36%) fuel and 8/25gU/cm 3 of LEU (19.75%) in WWR-M5 fuel assembly (FA) geometry is required to match the fuel cycle length of the HEU (90%) case with the same end of cycle (EOEC) excess reactivity. For the equilibrium fuel cycle the fuel burnup and poisoning, the fast and thermal neutron fluxes, the reactivity worth of control rods were calculated for the reference case with HEU (90%) FA and for the MEU and LEU FA. The relative accuracy of this neutronic feasibility study of fuel enrichment reduction of the WWR-M reactor in Gatchina is sufficient to start the fabrication feasibility study of MEU (36%) WWR-M5 fuel assemblies. At the present stage of technology it seems hardly possible to manufacture LEU (19.75%) fuel elements in WWR-M5 geometry due to too high uranium density. Only a future R and D can solve the problem. (author)

  2. Feasibility study of archaeological structures scanning by muon tomography

    Energy Technology Data Exchange (ETDEWEB)

    Gómez, H.; Katsanevas, S.; Tonazzo, A. [Laboratoire Astroparticule et Cosmologie (APC) - Université Paris 7. Paris (France); Carloganu, C.; Niess, V. [Laboratoire de Physique Corpusculaire (LPC) - Université Blaise Pascal. Clermont - Ferrand (France); Gibert, D. [Géosciences Rennes - Université de Rennes 1. Rennes (France); Marteau, J. [Institute de Physique Nucléaire de Lyon (IPNL) - Université de Lyon (UCBL). Lyon (France)

    2015-08-17

    One of the main concerns in archaeology is to find of a method to study precisely archaeological structures in the least invasive way possible to avoid damage. The requirement of preserving the structures integrity prevents, in the case of pyramids or tumuli, the study of any internal structure (halls or tombs) which are not reachable by existing corridors. One non-invasive method is the muon tomography. By placing a detector which allows to register the muon direction after the structure, it is possible to have an idea of its composition based on the attenuation of the muon flux, which depends on the material length and density that muons have crossed. This technique, alone or together with other exploration techniques as seismic tomography or electrical resistivity tomography, can provide useful information about the internal structure of the archaeological form that can not be obtained by conventional archaeological methods. In this work, the time measurement necessary to obtain a significant result about the composition of an archaeological structure is estimated. To do that, a Monte Carlo simulation framework based on the MUSIC software, properly tuned for this study, has been developed. The particular case of the Kastas Amfipoli Macedonian tumulus has been considered to perform the simulations.

  3. Feasibility study of archaeological structures scanning by muon tomography

    International Nuclear Information System (INIS)

    Gómez, H.; Katsanevas, S.; Tonazzo, A.; Carloganu, C.; Niess, V.; Gibert, D.; Marteau, J.

    2015-01-01

    One of the main concerns in archaeology is to find of a method to study precisely archaeological structures in the least invasive way possible to avoid damage. The requirement of preserving the structures integrity prevents, in the case of pyramids or tumuli, the study of any internal structure (halls or tombs) which are not reachable by existing corridors. One non-invasive method is the muon tomography. By placing a detector which allows to register the muon direction after the structure, it is possible to have an idea of its composition based on the attenuation of the muon flux, which depends on the material length and density that muons have crossed. This technique, alone or together with other exploration techniques as seismic tomography or electrical resistivity tomography, can provide useful information about the internal structure of the archaeological form that can not be obtained by conventional archaeological methods. In this work, the time measurement necessary to obtain a significant result about the composition of an archaeological structure is estimated. To do that, a Monte Carlo simulation framework based on the MUSIC software, properly tuned for this study, has been developed. The particular case of the Kastas Amfipoli Macedonian tumulus has been considered to perform the simulations

  4. Feasibility study of archaeological structures scanning by muon tomography

    Science.gov (United States)

    Gómez, H.; Carloganu, C.; Gibert, D.; Marteau, J.; Niess, V.; Katsanevas, S.; Tonazzo, A.

    2015-08-01

    One of the main concerns in archaeology is to find of a method to study precisely archaeological structures in the least invasive way possible to avoid damage. The requirement of preserving the structures integrity prevents, in the case of pyramids or tumuli, the study of any internal structure (halls or tombs) which are not reachable by existing corridors. One non-invasive method is the muon tomography. By placing a detector which allows to register the muon direction after the structure, it is possible to have an idea of its composition based on the attenuation of the muon flux, which depends on the material length and density that muons have crossed. This technique, alone or together with other exploration techniques as seismic tomography or electrical resistivity tomography, can provide useful information about the internal structure of the archaeological form that can not be obtained by conventional archaeological methods. In this work, the time measurement necessary to obtain a significant result about the composition of an archaeological structure is estimated. To do that, a Monte Carlo simulation framework based on the MUSIC software, properly tuned for this study, has been developed. The particular case of the Kastas Amfipoli Macedonian tumulus has been considered to perform the simulations.

  5. Automatic detection of hemorrhagic pericardial effusion on PMCT using deep learning - a feasibility study.

    Science.gov (United States)

    Ebert, Lars C; Heimer, Jakob; Schweitzer, Wolf; Sieberth, Till; Leipner, Anja; Thali, Michael; Ampanozi, Garyfalia

    2017-12-01

    Post mortem computed tomography (PMCT) can be used as a triage tool to better identify cases with a possibly non-natural cause of death, especially when high caseloads make it impossible to perform autopsies on all cases. Substantial data can be generated by modern medical scanners, especially in a forensic setting where the entire body is documented at high resolution. A solution for the resulting issues could be the use of deep learning techniques for automatic analysis of radiological images. In this article, we wanted to test the feasibility of such methods for forensic imaging by hypothesizing that deep learning methods can detect and segment a hemopericardium in PMCT. For deep learning image analysis software, we used the ViDi Suite 2.0. We retrospectively selected 28 cases with, and 24 cases without, hemopericardium. Based on these data, we trained two separate deep learning networks. The first one classified images into hemopericardium/not hemopericardium, and the second one segmented the blood content. We randomly selected 50% of the data for training and 50% for validation. This process was repeated 20 times. The best performing classification network classified all cases of hemopericardium from the validation images correctly with only a few false positives. The best performing segmentation network would tend to underestimate the amount of blood in the pericardium, which is the case for most networks. This is the first study that shows that deep learning has potential for automated image analysis of radiological images in forensic medicine.

  6. Feasibility study on plan to utilize livestock excreta for bio-gas in Miyagi Village (Gunma Prefecture). Investigations on projects including district new energy vision establishment in fiscal 2000, and on feasibility for commercialization; Miyagimura chikusan haisetsubutsu bio gas ka energy riyo keikaku feasibility study. 2000 nendo chiiki shin energy vision sakutei nado jigyo, jigyoka feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    With objectives to utilize energy available from livestock excreta, and to properly treat the livestock excreta, a feasibility study was performed on a plan to utilize livestock excreta for bio-gas. The system to be developed is a livestock wastes treatment system to utilize gas generated by efficiently fermenting the excreta as fuel, and residual sludge solids as compost. The activity achievements were put into order by the following nine items: 1) purpose of the feasibility study, 2) method for the feasibility study, 3) the situation where the livestock industry and the hog raising industry were selected as the object of the investigation, 4) properties of hog excreta, characteristics in urine foul water treatment, technologies for urine foul water treatment (biological treatment), 5) bio-gasification of livestock wastes, 6) the basic conditions for investigating the demonstration bio-bas plants, 7) proposals and standard cases of the demonstration bio gas plants, 8) discussions and positioning of the basic system for the demonstration bio gas plants, and 9) conclusion. (NEDO)

  7. ARAC feasibility study for the NRC Phase I: final report

    International Nuclear Information System (INIS)

    Rosen, L.C.; Orphan, R.C.

    1979-11-01

    The feasibility of implementing ARAC (Atmospheric Release Advisory Capability) services in a particular nuclear power plant is examined. The criteria for selecting Rancho Seco are discussed and the physical, meteorological and procedural factors related to the plant are assessed. The potential benefits and limitations of implementing ARAC at Rancho Seco are analyzed. The costs of employing the system at the nuclear power plant are given for alternative plans. A training and familiarization program is outlined

  8. FEASIBILITY STUDY OF PRESSURE PULSING PIPELINE UNPLUGGING TECHNOLOGIES FOR HANFORD

    Energy Technology Data Exchange (ETDEWEB)

    Servin, M. A. [Washington River Protection Solutions, LLC, Richland, WA (United States); Garfield, J. S. [AEM Consulting, LLC (United States); Golcar, G. R. [AEM Consulting, LLC (United States)

    2012-12-20

    The ability to unplug key waste transfer routes is generally essential for successful tank farms operations. All transfer lines run the risk of plugging but the cross site transfer line poses increased risk due to its longer length. The loss of a transfer route needed to support the waste feed delivery mission impacts the cost and schedule of the Hanford clean up mission. This report addresses the engineering feasibility for two pressure pulse technologies, which are similar in concept, for pipeline unplugging.

  9. Long-range eye tracking: A feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Jayaweera, S.K.; Lu, Shin-yee

    1994-08-24

    The design considerations for a long-range Purkinje effects based video tracking system using current technology is presented. Past work, current experiments, and future directions are thoroughly discussed, with an emphasis on digital signal processing techniques and obstacles. It has been determined that while a robust, efficient, long-range, and non-invasive eye tracking system will be difficult to develop, such as a project is indeed feasible.

  10. Feasibility Study Of Pressure Pulsing Pipeline Unplugging Technologies For Hanford

    International Nuclear Information System (INIS)

    Servin, M. A.; Garfield, J. S.; Golcar, G. R.

    2012-01-01

    The ability to unplug key waste transfer routes is generally essential for successful tank farms operations. All transfer lines run the risk of plugging but the cross site transfer line poses increased risk due to its longer length. The loss of a transfer route needed to support the waste feed delivery mission impacts the cost and schedule of the Hanford clean up mission. This report addresses the engineering feasibility for two pressure pulse technologies, which are similar in concept, for pipeline unplugging

  11. 78 FR 57624 - Availability of a Draft Integrated Feasibility Report (Feasibility Study/Environmental Impact...

    Science.gov (United States)

    2013-09-19

    ... creation and reestablishment of historic riparian strand and freshwater marsh habitat to support increased populations of wildlife and enhance habitat connectivity within the study area, as well as to provide opportunities for connectivity to ecological zones such as the Santa Monica Mountains, Verdugo Hills, Elysian...

  12. Feasibility study--computerized application of the hazardous material regulations

    International Nuclear Information System (INIS)

    Ferrada, J.J.; Green, V.M.; Rawl, R.R.

    1992-09-01

    The feasibility of developing a full expert system for transportation and packaging of hazardous and radioactive materials was initiated within the framework of three subtasks: (1) analysis of commercial packages related to regulation scanning, (2) analysis of computer languages to develop the expert system, and (3) development of expert system prototypes. The strategy to develop the latter subtask was to first,develop modules to capture the knowledge of different areas of transportation and packaging and second, to analyze the feasibility of appending these different modules in one final full package. The individual modules development contemplated one prototype for transporting and packaging of radioactive material and another for transporting hazardous chemical materials. In the event that it is not feasible to link these two packages, the modules can always be used as stand-alone tools, or linked as a single package with some restrictions in their applicability. The work done during this fiscal year has focused on developing a prototype for transporting radioactive materials

  13. A feasibility study for an International Year of Landcare

    Science.gov (United States)

    Mutota, E.; Arnalds, A.

    2009-04-01

    Human-induced activities place enormous pressures on the land worldwide, creating competition and conflict, and suboptimal use of the land. Climate change, loss of biodiversity and land degradation leads to decreasing productivity, food and water shortages, and reduced economic benefits, among others. In order to address these challenges and achieve sustainability goals, the need to change the way global resources are being utilized is crucial. A holistic and integrated community-based approach such as Landcare could be a viable approach to meet this worldwide challenge. Landcare is about committed people working together on land rehabilitation and restoration projects at the local level, transforming attitudes and stimulating new ideas among land users, generating support and building partnerships between and among local communities, governments and the private sector. Landcare initiatives have grown in a number of countries where success stories of actions on the ground clearly show the wider application of the Landcare approach in resolving many of the world's environmental problems and livelihood challenges. However, the potential of Landcare have not yet been widely exploited on a scale that really matters—as local actions build up towards global progress, there is more scope for unified efforts towards a global Landcare movement. Following the recommendation given at the International Forum on Soils, Society and Global Change in 2007 in Iceland (http://www.iisd.ca/YMB/SDFSS/), an International Year of Landcare should be established. Such a year would bring into focus efforts to build local capacity and share knowledge and experiences between provinces, countries and continents on Landcare. Additionally, holding a year concerned with Landcare would greatly contribute to the attainment of the Millennium Development Goals, the UN environmental conventions and many other sustainability goals. Our study supports the notion that Landcare offers a robust platform

  14. Introduction and feasibility study of the HD-270 MLC

    International Nuclear Information System (INIS)

    Kim, Dae Young; Kim Won Taek; Lee, Hwa Jung; Lee, Kang Hyeok

    2003-01-01

    The multileaf collimator(MLC) has many advantages, but use of the MLC increased effective penumbra and isodose undulation in dose distribution compared with that of an alloy block. In this work, we introduced the HD-270 MLC, which can improve the above disadvantages of MLC, and reported its feasibility study. The HD-270 MLC is a technique which combines the use of the existing Siemens multileaf collimator(3D MLC) with patient translation perpendicular to the leaf plane. The technique produces a smoothed isodose distribution with the reduced isodose undulation and effective penumbra. To assess the efficacy of the HD-270 technique and determine the appropriate resolution, a polygonal shaped MLC field was made to produce field edge angles from 0 degree to 75 degree with a step of 15 degree. Each HD-270 group was generated according to the allowed resolution, i. e., 5, 3, and 2 mm. The experiment was carried out on Primus, a Siemens linear accelerator configured with HD-270 MLC. The total 60 MU of 6 MV photon beam was delivered to X-Omat film (Kodak, USA) at a SAD of 100 cm and 1.5 cm depth in solid water phantom. Exposed films were scanned by Lumiscan75(LUMISYS) and analyzed using RIT113 software (Radiological Imaging Technology Inc., USA). To test the mechanical accuracy of table movement, the transverse, longitudinal, and vertical positions were controlled by a consol with ±5 mm, ±4 mm, ±3 mm, and ±2 mm steps, and then measured using a dial gauge with an accuracy of 0.001 inch. During the experiments, the table loaded with about 50 Kg human phantom to simulate the real treatment situation. The effective penumbra and isodose undulation became larger with increase the resolution and field edge angle. The accuracy of the table movement on each direction is good within the ±1 mm. Clinical use of the MLC can be increased by using of the HD-270 MLC which complements to the disadvantages of the MLC.

  15. Seabed Filter Feasibility Study of Om Almisk Island

    KAUST Repository

    Sesler, Kathryn

    2012-06-01

    Freshwater access has always been and is continuing to be a severe problem in desert coastal regions, despite the fact that they have an unlimited supply of easily accessible saline water. Water desalination plants are well established and heavily relied upon throughout the Middle East, Saudi Arabia in particular. However, water desalination tends to be a very expensive and energy intensive solution to the problem. The transition from using open water intake systems and all of the pretreatment processes that they require, to using seabed water filters as an intake, would potentially reduce the lifetime costs, energy consumption, and environmental impacts commonly associated with water desalination. This is because the filtration process that the seabed filter generates, serves as sufficient pretreatment for seawater as well as eliminating any risk of entrainment or impingement of marine organisms. The main objective of this research is to conduct a feasibility study on Om Almisk Island, an island off the coast of King Abdullah University of Science and Technology (KAUST), to determine if it would be a suitable location to construct a seabed water filter as a replacement for the current open water intake. The Om Almisk Island site was evaluated through collection of sand samples over a radial grid around Om Almisk Island and sample analysis using grain size distribution, porosity, and hydraulic conductivity. The lack of mud, high hydraulic conductivity, proximity to KAUST, and the shallow waters of the sandy apron surrounding Om Almisk Island make this an ideal location for a seabed water filter to be used as an intake and pretreatment for the KAUST desalination plant. This location also has low tide change and the presence of benthic macrofauna to create bioturbation in the sediments, which could inhibit the growth of a schmutzdecke. If this biological layer forms, it could drastically reduce the hydraulic conductivity of the system. Due to the high hydraulic

  16. Quantitative analysis of multiple biokinetic models using a dynamic water phantom: A feasibility study

    Science.gov (United States)

    Chiang, Fu-Tsai; Li, Pei-Jung; Chung, Shih-Ping; Pan, Lung-Fa; Pan, Lung-Kwang

    2016-01-01

    ABSTRACT This study analyzed multiple biokinetic models using a dynamic water phantom. The phantom was custom-made with acrylic materials to model metabolic mechanisms in the human body. It had 4 spherical chambers of different sizes, connected by 8 ditches to form a complex and adjustable water loop. One infusion and drain pole connected the chambers to an auxiliary silicon-based hose, respectively. The radio-active compound solution (TC-99m-MDP labeled) formed a sealed and static water loop inside the phantom. As clean feed water was infused to replace the original solution, the system mimicked metabolic mechanisms for data acquisition. Five cases with different water loop settings were tested and analyzed, with case settings changed by controlling valve poles located in the ditches. The phantom could also be changed from model A to model B by transferring its vertical configuration. The phantom was surveyed with a clinical gamma camera to determine the time-dependent intensity of every chamber. The recorded counts per pixel in each chamber were analyzed and normalized to compare with theoretical estimations from the MATLAB program. Every preset case was represented by uniquely defined, time-dependent, simultaneous differential equations, and a corresponding MATLAB program optimized the solutions by comparing theoretical calculations and practical measurements. A dimensionless agreement (AT) index was recommended to evaluate the comparison in each case. ATs varied from 5.6 to 48.7 over the 5 cases, indicating that this work presented an acceptable feasibility study. PMID:27286096

  17. Feasibility studies for alpha waste disposal on geological formations in France

    International Nuclear Information System (INIS)

    Jaouen, C.; Boulanger, A.

    1985-01-01

    Since 1977, SGN has been involved in many feasibility studies and consultant works in the fields of HLW storages. Starting as nuclear consultant company in the KBS review of the long term storage of HLW, SGN and Geostock were entrusted in 1978 by the EEC for the basic design and evaluation of the deep storage into granite rock of HLW, followed by a participation in the thermal sensitivity study of such a storage. The cooperation with Geostock was first extended in 1981 to a preliminary study of HLW storage conditions in granite for a Japanese company, and then in France for several feasibility studies of HLW and TRU waste geological disposal. Three kinds of scenarios have been forecasted and evaluated in the case of vitrified HLW storage, allowing the thermal power to be decreased and the whole management scheme to be optimized. More recently, SGN participation to French engineering studies has been extended by ANDRA to the TRU waste repository evaluation. All these works for French authorities have been performed in a close connection with several specialized departments in the CEA group, and with the help of geological specialists, under the leadership of ANDRA [fr

  18. Feasibility studies for alpha waste disposal on geological formations in France

    International Nuclear Information System (INIS)

    Jaouen, C.; Boulanger, A.

    1986-01-01

    Since 1977, SGN has been involved in many feasibility studies and consultant works in the fields of HLW storages. Starting as nuclear consultant company in the KBS review of the long term storage of HLW, SGN and GEOSTOCK were entrusted in 1978 by the EEC for the basic design and evaluation of the deep storage into granite rock of HLW, followed by a participation in the thermal sensitivity study of such a storage. The cooperation with GEOSTOCK was first extended in 1981 to a preliminary study of HLW storage conditions in granite for a Japanese company, and then in France for several feasibility studies of HLW and TRU waste geological disposal. Three kinds of scenarios have been forecasted and evaluated in the case of vitrified HLW storage, allowing the thermal power to be decreased and the whole management scheme to be optimized. More recently, SGN participation to French engineering studies has been extended by ANDRA to the TRU waste repository evaluation. All these works for French authorities have been performed in a close connection with several specialized departments in the CEA group, and with the help of geological specialists, under the leadership of ANDRA [fr

  19. Case study - Czechoslovakia

    International Nuclear Information System (INIS)

    Kovar, P.

    1986-01-01

    In the lecture Case Study - Czechoslovakia with the sub-title 'Unified System of Personnel Preparation for Nuclear Programme in Czechoslovakia' the actual status and the current experience of NPP personnel training and preparation in Czechoslovakia are introduced. The above mentioned training system is presented and demonstrated by the story of a proxy person who is going to become shift engineer in a nuclear power plant in Czechoslovakia. (orig./HP)

  20. Case Studies - Cervical Cancer

    Centers for Disease Control (CDC) Podcasts

    2010-10-15

    Dr. Alan Waxman, a professor of obstetrics and gynecology at the University of New Mexico and chair of the American College of Obstetricians and Gynecologists (ACOG) committee for the underserved, talks about several case studies for cervical cancer screening and management.  Created: 10/15/2010 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP), Division of Cancer Prevention and Control (DCPC).   Date Released: 6/9/2010.

  1. Defining Feasibility and Pilot Studies in Preparation for Randomised Controlled Trials: Development of a Conceptual Framework.

    Directory of Open Access Journals (Sweden)

    Sandra M Eldridge

    Full Text Available We describe a framework for defining pilot and feasibility studies focusing on studies conducted in preparation for a randomised controlled trial. To develop the framework, we undertook a Delphi survey; ran an open meeting at a trial methodology conference; conducted a review of definitions outside the health research context; consulted experts at an international consensus meeting; and reviewed 27 empirical pilot or feasibility studies. We initially adopted mutually exclusive definitions of pilot and feasibility studies. However, some Delphi survey respondents and the majority of open meeting attendees disagreed with the idea of mutually exclusive definitions. Their viewpoint was supported by definitions outside the health research context, the use of the terms 'pilot' and 'feasibility' in the literature, and participants at the international consensus meeting. In our framework, pilot studies are a subset of feasibility studies, rather than the two being mutually exclusive. A feasibility study asks whether something can be done, should we proceed with it, and if so, how. A pilot study asks the same questions but also has a specific design feature: in a pilot study a future study, or part of a future study, is conducted on a smaller scale. We suggest that to facilitate their identification, these studies should be clearly identified using the terms 'feasibility' or 'pilot' as appropriate. This should include feasibility studies that are largely qualitative; we found these difficult to identify in electronic searches because researchers rarely used the term 'feasibility' in the title or abstract of such studies. Investigators should also report appropriate objectives and methods related to feasibility; and give clear confirmation that their study is in preparation for a future randomised controlled trial designed to assess the effect of an intervention.

  2. Defining Feasibility and Pilot Studies in Preparation for Randomised Controlled Trials: Development of a Conceptual Framework.

    Science.gov (United States)

    Eldridge, Sandra M; Lancaster, Gillian A; Campbell, Michael J; Thabane, Lehana; Hopewell, Sally; Coleman, Claire L; Bond, Christine M

    2016-01-01

    We describe a framework for defining pilot and feasibility studies focusing on studies conducted in preparation for a randomised controlled trial. To develop the framework, we undertook a Delphi survey; ran an open meeting at a trial methodology conference; conducted a review of definitions outside the health research context; consulted experts at an international consensus meeting; and reviewed 27 empirical pilot or feasibility studies. We initially adopted mutually exclusive definitions of pilot and feasibility studies. However, some Delphi survey respondents and the majority of open meeting attendees disagreed with the idea of mutually exclusive definitions. Their viewpoint was supported by definitions outside the health research context, the use of the terms 'pilot' and 'feasibility' in the literature, and participants at the international consensus meeting. In our framework, pilot studies are a subset of feasibility studies, rather than the two being mutually exclusive. A feasibility study asks whether something can be done, should we proceed with it, and if so, how. A pilot study asks the same questions but also has a specific design feature: in a pilot study a future study, or part of a future study, is conducted on a smaller scale. We suggest that to facilitate their identification, these studies should be clearly identified using the terms 'feasibility' or 'pilot' as appropriate. This should include feasibility studies that are largely qualitative; we found these difficult to identify in electronic searches because researchers rarely used the term 'feasibility' in the title or abstract of such studies. Investigators should also report appropriate objectives and methods related to feasibility; and give clear confirmation that their study is in preparation for a future randomised controlled trial designed to assess the effect of an intervention.

  3. A robotic wheelchair trainer: design overview and a feasibility study

    Science.gov (United States)

    2010-01-01

    Background Experiencing independent mobility is important for children with a severe movement disability, but learning to drive a powered wheelchair can be labor intensive, requiring hand-over-hand assistance from a skilled therapist. Methods To improve accessibility to training, we developed a robotic wheelchair trainer that steers itself along a course marked by a line on the floor using computer vision, haptically guiding the driver's hand in appropriate steering motions using a force feedback joystick, as the driver tries to catch a mobile robot in a game of "robot tag". This paper provides a detailed design description of the computer vision and control system. In addition, we present data from a pilot study in which we used the chair to teach children without motor impairment aged 4-9 (n = 22) to drive the wheelchair in a single training session, in order to verify that the wheelchair could enable learning by the non-impaired motor system, and to establish normative values of learning rates. Results and Discussion Training with haptic guidance from the robotic wheelchair trainer improved the steering ability of children without motor impairment significantly more than training without guidance. We also report the results of a case study with one 8-year-old child with a severe motor impairment due to cerebral palsy, who replicated the single-session training protocol that the non-disabled children participated in. This child also improved steering ability after training with guidance from the joystick by an amount even greater than the children without motor impairment. Conclusions The system not only provided a safe, fun context for automating driver's training, but also enhanced motor learning by the non-impaired motor system, presumably by demonstrating through intuitive movement and force of the joystick itself exemplary control to follow the course. The case study indicates that a child with a motor system impaired by CP can also gain a short-term benefit

  4. Endovascular stentectomy using the snare over stent-retriever (SOS technique: An experimental feasibility study.

    Directory of Open Access Journals (Sweden)

    Tareq Meyer

    Full Text Available Feasibility of endovascular stentectomy using a snare over stent-retriever (SOS technique was evaluated in a silicon flow model and an in vivo swine model. In vitro, stentectomy of different intracranial stents using the SOS technique was feasible in 22 out of 24 (92% retrieval maneuvers. In vivo, stentectomy was successful in 10 out of 10 procedures (100%. In one case self-limiting vasospasm was observed angiographically as a technique related complication in the animal model. Endovascular stentectomy using the SOS technique is feasible in an experimental setting and may be transferred to a clinical scenario.

  5. Feasibility and acceptability of reducing workplace sitting time: a qualitative study with Australian office workers.

    Science.gov (United States)

    Hadgraft, Nyssa T; Brakenridge, Charlotte L; LaMontagne, Anthony D; Fjeldsoe, Brianna S; Lynch, Brigid M; Dunstan, David W; Owen, Neville; Healy, Genevieve N; Lawler, Sheleigh P

    2016-09-05

    Office workers spend a large proportion of their working hours sitting. This may contribute to an increased risk of chronic disease and premature mortality. While there is growing interest in workplace interventions targeting prolonged sitting, few qualitative studies have explored workers' perceptions of reducing occupational sitting outside of an intervention context. This study explored barriers to reducing office workplace sitting, and the feasibility and acceptability of strategies targeting prolonged sitting in this context. Semi-structured interviews were conducted with a convenience sample of 20 office workers (50 % women), including employees and managers, in Melbourne, Australia. The three organisations (two large, and one small organisation) were from retail, health and IT industries and had not implemented any formalised approaches to sitting reduction. Questions covered barriers to reducing sitting, the feasibility of potential strategies aimed at reducing sitting, and perceived effects on productivity. Interviews were audiotaped and transcribed verbatim. Data were analysed using thematic analysis. Participants reported spending most (median: 7.2 h) of their working hours sitting. The nature of computer-based work and exposure to furniture designed for a seated posture were considered to be the main factors influencing sitting time. Low cost strategies, such as standing meetings and in-person communication, were identified as feasible ways to reduce sitting time and were also perceived to have potential productivity benefits. However, social norms around appropriate workplace behaviour and workload pressures were perceived to be barriers to uptake of these strategies. The cost implications of height-adjustable workstations influenced perceptions of feasibility. Managers noted the need for an evidence-based business case supporting action on prolonged sitting, particularly in the context of limited resources and competing workplace health priorities

  6. Feasibility and acceptability of reducing workplace sitting time: a qualitative study with Australian office workers

    Directory of Open Access Journals (Sweden)

    Nyssa T. Hadgraft

    2016-09-01

    Full Text Available Abstract Background Office workers spend a large proportion of their working hours sitting. This may contribute to an increased risk of chronic disease and premature mortality. While there is growing interest in workplace interventions targeting prolonged sitting, few qualitative studies have explored workers’ perceptions of reducing occupational sitting outside of an intervention context. This study explored barriers to reducing office workplace sitting, and the feasibility and acceptability of strategies targeting prolonged sitting in this context. Methods Semi-structured interviews were conducted with a convenience sample of 20 office workers (50 % women, including employees and managers, in Melbourne, Australia. The three organisations (two large, and one small organisation were from retail, health and IT industries and had not implemented any formalised approaches to sitting reduction. Questions covered barriers to reducing sitting, the feasibility of potential strategies aimed at reducing sitting, and perceived effects on productivity. Interviews were audiotaped and transcribed verbatim. Data were analysed using thematic analysis. Results Participants reported spending most (median: 7.2 h of their working hours sitting. The nature of computer-based work and exposure to furniture designed for a seated posture were considered to be the main factors influencing sitting time. Low cost strategies, such as standing meetings and in-person communication, were identified as feasible ways to reduce sitting time and were also perceived to have potential productivity benefits. However, social norms around appropriate workplace behaviour and workload pressures were perceived to be barriers to uptake of these strategies. The cost implications of height-adjustable workstations influenced perceptions of feasibility. Managers noted the need for an evidence-based business case supporting action on prolonged sitting, particularly in the context of

  7. Feasibility and Pilot Studies in Palliative Care Research: A Systematic Review.

    Science.gov (United States)

    Jones, Terry A; Olds, Timothy S; Currow, David C; Williams, Marie T

    2017-07-01

    Feasibility and pilot study designs are common in palliative care research. Finding standard guidelines on the structure and reporting of these study types is difficult. In feasibility and pilot studies in palliative care research, to determine 1) how commonly a priori feasibility are criteria reported and whether results are subsequently reported against these criteria? and 2) how commonly are participants' views on acceptability of burden of the study protocol assessed? Four databases (OVID Medline, EMBASE, CINAHL, and PubMed via caresearch.com.au.) were searched. Search terms included palliative care, terminal care, advance care planning, hospice, pilot, feasibility, with a publication date between January 1, 2012 and December 31, 2013. Articles were selected and appraised by two independent reviewers. Fifty-six feasibility and/or pilot studies were included in this review. Only three studies had clear a priori criteria to measure success. Sixteen studies reported participant acceptability or burden with measures. Forty-eight studies concluded feasibility. The terms "feasibility" and "pilot" are used synonymously in palliative care research when describing studies that test for feasibility. Few studies in palliative care research outline clear criteria for success. The assessment of participant acceptability and burden is uncommon. A gold standard for feasibility study design in palliative care research that includes both clear criteria for success and testing of the study protocol for participant acceptability and burden is needed. Such a standard would assist with consistency in the design, conduct and reporting of feasibility and pilot studies. Copyright © 2017 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All rights reserved.

  8. Final focus system tuning studies towards Compact Linear Collider feasibility

    Science.gov (United States)

    Marin, E.; Latina, A.; Tomás, R.; Schulte, D.

    2018-01-01

    In this paper we present the latest results regarding the tuning study of the baseline design of the final focus system of the Compact Linear Collider (CLIC-FFS). CLIC aims to provide collisions to the experiments at a luminosity above 1034 c m-2 s-1 . In order to deliver such luminosity in a single pass machine, the vertical beam size at the interaction point (IP) is reduced to about 1 nm, which imposes unprecedented tuning difficulties to the system. In previous studies, 90% of the machines reached 90% of the nominal luminosity at the expense of 18 000 luminosity measurements, when considering beam position monitor errors and transverse misalignments of magnets for a single beam case. In the present study, additional static imperfections as, roll misalignments, strength v2.epss are included. Moreover both e- and e+ beamlines are properly simulated. A new tuning procedure based on linear and nonlinear knobs is implemented to effectively cure the most relevant beam size aberrations at the IP. The obtained results for single and double beam studies under solely static imperfections are presented.

  9. Tuna cannery energy conservation interventions: Technical/economic feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Florio, G. (Calabria Univ. Arcavacata di Rende (Italy). Dipt. di Meccanica)

    An energy audit was conducted on a 230,000 can (x 80 g)/day tuna cannery to determine where technically and economically feasible energy savings interventions could be made. The plant is equipped with an oil fired boiler which supplies steam for cooking and sterilization purposes. In the energy/cost analysis, it was found that the most significant and cost effective energy savings could be obtained by the substitution of the four sterilization chambers with three sets of twin sterilization/heat exchange chambers.

  10. Failure Modes and Effects Analysis (FMEA) Assistant Tool Feasibility Study

    Science.gov (United States)

    Flores, Melissa; Malin, Jane T.

    2013-01-01

    An effort to determine the feasibility of a software tool to assist in Failure Modes and Effects Analysis (FMEA) has been completed. This new and unique approach to FMEA uses model based systems engineering concepts to recommend failure modes, causes, and effects to the user after they have made several selections from pick lists about a component s functions and inputs/outputs. Recommendations are made based on a library using common failure modes identified over the course of several major human spaceflight programs. However, the tool could be adapted for use in a wide range of applications from NASA to the energy industry.

  11. Failure Modes and Effects Analysis (FMEA) Assistant Tool Feasibility Study

    Science.gov (United States)

    Flores, Melissa D.; Malin, Jane T.; Fleming, Land D.

    2013-09-01

    An effort to determine the feasibility of a software tool to assist in Failure Modes and Effects Analysis (FMEA) has been completed. This new and unique approach to FMEA uses model based systems engineering concepts to recommend failure modes, causes, and effects to the user after they have made several selections from pick lists about a component's functions and inputs/outputs. Recommendations are made based on a library using common failure modes identified over the course of several major human spaceflight programs. However, the tool could be adapted for use in a wide range of applications from NASA to the energy industry.

  12. Feasibility study of the Dragon reactor for HTGR fuel testing

    International Nuclear Information System (INIS)

    Wallroth, C.F.

    1975-01-01

    The Organization of European Community Development (OECD) Dragon high-temperature reactor project has performed HTGR fuel and fuel element testing for about 10 years. To date, a total of about 250 fuel elements have been irradiated and the test program continues. The feasibility of using this test facility for HTGR fuel testing, giving special consideration to U. S. needs, is evaluated. A detailed description for design, preparation, and data acquisition of a test experiment is given together with all possible options on supporting work, which could be carried out by the experienced Dragon project staff. 11 references. (U.S.)

  13. Cogeneration using small sized series connected units: Feasibility study

    International Nuclear Information System (INIS)

    Tondelli, F.; Bergamini, G.

    1992-01-01

    This paper evidences the technical/economic feasibility of the use of methane fuelled modular cogeneration systems based on small series connected Otto or Diesel cycle engines delivering from 20 to 90 kW of power. Ample reference is made to the successful application of modular cogeneration systems to supply low temperature thermal energy to hospitals, hotels, food processing firms, etc., in Italy. The cost benefit analysis covers many aspects: design, manufacturing, operation, performance, maintenance and safety. Suggestions are also made as to optimum contractual arrangements for equipment service and maintenance, as well as, for the exchange of power with local utilities

  14. Feasibility study of 5MW superconducting wind turbine generator

    DEFF Research Database (Denmark)

    Abrahamsen, Asger Bech; Jensen, Bogi Bech; Seiler, E.

    2011-01-01

    The feasibility of installing a direct drive superconducting generator in the 5MW reference offshore wind turbine of the National Renewable Energy Laboratory (NREL) has been examined. The engineering current densities Je obtained in a series of race track coils have been combined with magnetization...... measurements to estimate the properties of suitable field coils for a synchronous generator, which is more light weight than the conventional used combination of a gear box and a fast rotating generator. An analytical model and finite element simulations have been used to estimate the active mass of generators...

  15. Feasibility of robotic exoskeleton ambulation in a C4 person with incomplete spinal cord injury: a case report.

    Science.gov (United States)

    Lester, Robert M; Gorgey, Ashraf S

    2018-01-01

    To determine whether an individual with C4 incomplete spinal cord injury (SCI) with limited hand functions can effectively operate a powered exoskeleton (Ekso) to improve parameters of physical activity as determined by swing-time, up-time, walk-time, and total number of steps. A 21-year-old male with incomplete chronic (>1 year postinjury) SCI C4, participated in a clinical exoskeleton program to determine the feasibility of standing up and walking with limited hand functions. The participant was invited to attend 3 sessions including fitting, familiarization and gait training separated by one week intervals. Walk-time, up-time and total number of steps were measured during each training session. A complete body composition assessment using dual-energy X-ray absorptiometry (DXA) of the spine, knees and hips was conducted before training.Using a platform walker and cuffing both hands, the participant managed to stand up and ambulate successfully using exoskeleton. Over the course of 2 weeks, maximum walk-time increased from 7 to 17 min and number of steps increased from 83 to 589 steps. The total up-time increased from 19 to 31 min. Exoskeleton training may be a safe and feasible approach for persons with higher levels of SCI after effectively providing a supportive assistive device for weight shifting. The current case study demonstrates the use of a powered exoskeleton for an individual with high level tetraplegia (C4 and above) and limited hand functions.

  16. Breast tumor classification using axial shear strain elastography: a feasibility study

    International Nuclear Information System (INIS)

    Thitaikumar, Arun; Ophir, Jonathan; Mobbs, Louise M; Kraemer-Chant, Christina M; Garra, Brian S

    2008-01-01

    Recently, the feasibility of visualizing the characteristics of bonding at an inclusion-background boundary using axial-shear strain elastography was demonstrated. In this paper, we report a feasibility study on the utility of the axial-shear strain elastograms in the classification of in vivo breast tumor as being benign or malignant. The study was performed using data sets obtained from 15 benign and 15 malignant cases that were biopsy proven. A total of three independent observers were trained, and their services were utilized for the study. A total of 9 cases were used as training set and the remaining cases were used as testing set. The feature from the axial-shear strain elastogram, namely, the area of the axial-shear region, was extracted by the observers. The observers also outlined the tumor area on the corresponding sonogram, which was used to normalize the area of the axial-shear strain region. There are several observations that can be drawn from the results. First, the result indicates that the observers consistently (∼82% of the cases) noticed the characteristic pattern of the axial-shear strain distribution data as predicted in the previous simulation studies, i.e. alternating regions of positive and negative axial-shear strain values around the tumor-background interface. Second, the analysis of the result suggests that in approximately 57% of the cases in which the observers did not visualize tumor in the sonogram, the elastograms helped them to locate the tumor. Finally, the analysis of the result suggests that for the discriminant feature value of 0.46, the number of unnecessary biopsies could be reduced by 56.3% without compromising on sensitivity and on negative predictive value (NPV). Based on the results in this study, feature values greater than 0.75 appear to be indicative of malignancy, while values less than 0.46 to be indicative of benignity. Feature values between 0.46 and 0.75 may result in an overlap between benign and malignant

  17. Feasibility study of a family-focused intervention to improve outcomes for children with FASD.

    Science.gov (United States)

    Reid, Natasha; Dawe, Sharon; Harnett, Paul; Shelton, Doug; Hutton, Lauren; O'Callaghan, Frances

    2017-08-01

    Growing evidence shows that children with fetal alcohol spectrum disorder (FASD) can benefit from interventions, and specifically interventions focused on improving self-regulation. However, novel ways of improving outcomes for children with FASD need further investigation so that programs target not only the individual child but also the family context, which includes the parent-child relationship. The current study aimed to evaluate the feasibility of an adapted version of the Parents under Pressure (PuP) program that addresses self-regulatory processes, through improving the parent-child relationship and the use of mindfulness-based strategies for both children and parents. This was a mixed methods study. Feasibility was examined by evaluating recruitment, data collection/outcome measures, and intervention procedures. The study used a phenomenological approach to obtain qualitative information from caregivers and a single-case experimental design to evaluate the preliminary participant responses to the intervention. Two out of three families completed treatment. The recruitment and intervention procedures were found to be suitable for and acceptable to the families involved. Some concerns were identified regarding the outcome measures that would need to be addressed in future research. Quantitative and qualitative outcomes were positive. The results provide preliminary support for the feasibility of an adapted version of the PuP program. Thus, offering a potential multi-component option, that aims to improve self-regulatory skills for children with FASD, through focusing on improving the parent-child relationship and incorporating mindfulness-based techniques for both parents and children. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Spirometry in elderly laryngectomized patients: A feasibility study.

    Science.gov (United States)

    Izzo, Alessandro; Perrotta, Fabio; Cennamo, Antonio; Cerqua, Francesco Saverio; Rinaldi, Luca; Mazzella, Antonio; Grella, Edoardo; Tranfa, Carmelindo; Bianco, Andrea; Stefanelli, Francesco; Mazzarella, Gennaro

    2016-09-01

    Laryngeal cancer is the second most common respiratory neoplasm after lung cancer. Laryngectomy is a well established treatment for larynx cancers which involve relevant anatomic alterations. Spirometry is an essential investigation tool for diagnosis and severity of respiratory diseases, difficult to perform in laryngectomees. 43 consecutive laryngectomized patients were enrolled from July 2014 to March 2015. Patients fulfilling inclusion criteria underwent spirometry at baseline assessment and after two days. During the examination, the spirometer was placed directly on the stoma of the patient, through mouthpiece "Spirometry Filter 74". At baseline, 26 eligible laryngectomees correctly performed the spirometry test with mouthpiece adhering to the stoma; 4 patients refused to perform the second spirometry after 2 days. The feasibility of spirometry examination in these patients was 100% despite difficulties in the execution of the test. The Pearson coefficient of reproducibility for FEV1, FVC and Tiffeneau Index was, respectively, 0.98, 0.94 and 0.77. Spirometry in laryngectomee patients is a feasible procedure for assessment of respiratory function; despite technical difficulties in the execution of the test, our results underline the reproducibility and repeatability of the spirometry. In conclusion, when performed within dedicated respiratory pathophysiology unit, spirometry is a reliable tool in the assessment and follow up of laryngectomees. Copyright © 2016 IJS Publishing Group Ltd. Published by Elsevier Ltd. All rights reserved.

  19. The feasibility study on fuel types for the KALIMER

    International Nuclear Information System (INIS)

    Hwang, W.; Nam, C.; Yim, J. S.; Na, B. C.; Hahn, D. H.; Kim, Y. I.; Kim, Y. C.; Park, C. K.

    1997-08-01

    The economics of LMR is largely dependent on the construction cost of the power plant, and the fuel cycle options usually constitute 20 to 30 % of total electricity generation cost. The choice of fuel cycle technology and the fuel type is important in order to develop a LMR with better economics, performance and safety. The LMR fuel types, whose performances have been proven up to 15 at% burnup, are MOX and IFR metal fuel. The base alloy, binary (U-10% Zr) metal fuel with HT9 is used as structural materials of KALIMER. The design concept of KALIMER fuel has been established through the investigation of technical feasibilities on the fuel and recycle systems for MOX and IFR metal fuel. According to the results of comparative analysis for MOX and metal fuel, metal fuel is better than MOX in view of safety, in-reactor performance, nuclear characteristics, economics and non-proliferation, while MOX fuels have advantages in the developmental status and technical cooperation potential. The overall performance of binary (U-10% Zr) metal fuel with HT9 cladding, which is a potential start-up fuel for KALIMER, is not only superior to that of MOX fuel, but also has enough technical feasibility in its high-burnup performance, safety and economics. (author). 54 ref., 13 tabs., 20 figs

  20. Power generation from MSW of Haridwar city: A feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Jain, Siddharth; Sharma, M.P. [Biofuel Research Laboratory, Alternate Hydro Energy Centre, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667 (India)

    2011-01-15

    Energy plays significant role in the development of a nation. The conventional sources, though exhausting and not environment friendly are being increasingly used. Looking at limited supplies and various environment problems associated with its uses, renewable energy sources are getting attention. Municipal solid waste [MSW] is getting importance in recent years. Having fewer disposal problems is being considered as valuable bio-energy resources. The MSW management involves collection, transportation, handling and conversion to energy by biological and thermal routes. The present paper reports the results of physical, proximate and TGA/DTA analysis, used to select the most appropriate method of energy conversion. Based on the energy potential available, the feasibility of energy conversion through biogas production using available waste has been carried out. The CDM benefits have also been considered. The cost of generation with and without CDM benefits is Rs. 1.36/- and Rs. 1.41/- per kWh respectively as compared to cost of energy from grid [Rs. 3.50/- per kWh]. Therefore power generation from MSW of Haridwar city using biomethanation conversion technology is feasible. (author)

  1. Feasibility of AmbulanCe-Based Telemedicine (FACT study: safety, feasibility and reliability of third generation in-ambulance telemedicine.

    Directory of Open Access Journals (Sweden)

    Laetitia Yperzeele

    Full Text Available Telemedicine is currently mainly applied as an in-hospital service, but this technology also holds potential to improve emergency care in the prehospital arena. We report on the safety, feasibility and reliability of in-ambulance teleconsultation using a telemedicine system of the third generation.A routine ambulance was equipped with a system for real-time bidirectional audio-video communication, automated transmission of vital parameters, glycemia and electronic patient identification. All patients ( ≥ 18 years transported during emergency missions by a Prehospital Intervention Team of the Universitair Ziekenhuis Brussel were eligible for inclusion. To guarantee mobility and to facilitate 24/7 availability, the teleconsultants used lightweight laptop computers to access a dedicated telemedicine platform, which also provided functionalities for neurological assessment, electronic reporting and prehospital notification of the in-hospital team. Key registrations included any safety issue, mobile connectivity, communication of patient information, audiovisual quality, user-friendliness and accuracy of the prehospital diagnosis.Prehospital teleconsultation was obtained in 41 out of 43 cases (95.3%. The success rates for communication of blood pressure, heart rate, blood oxygen saturation, glycemia, and electronic patient identification were 78.7%, 84.8%, 80.6%, 64.0%, and 84.2%. A preliminary prehospital diagnosis was formulated in 90.2%, with satisfactory agreement with final in-hospital diagnoses. Communication of a prehospital report to the in-hospital team was successful in 94.7% and prenotification of the in-hospital team via SMS in 90.2%. Failures resulted mainly from limited mobile connectivity and to a lesser extent from software, hardware or human error. The user acceptance was high.Ambulance-based telemedicine of the third generation is safe, feasible and reliable but further research and development, especially with regard to high

  2. Management of Uncomplicated Acute Appendicitis as Day Case Surgery: Feasibility and a Critical Analysis of Exclusion Criteria and Treatment Failure.

    Science.gov (United States)

    Grelpois, Gérard; Sabbagh, Charles; Cosse, Cyril; Robert, Brice; Chapuis-Roux, Emilie; Ntouba, Alexandre; Lion, Thierry; Regimbeau, Jean-Marc

    2016-11-01

    Day case surgery (DCS) for uncomplicated acute appendicitis (NCAA) is evaluated. The objective of this prospective, single-center, descriptive, nonrandomized, intention-to-treat cohort study was to assess the feasibility of DCS for NCAA with a critical analysis of the reasons for exclusion and treatment failures and a focus on patients discharged to home and admitted for DCS on the following day. From April 2013 to December 2015, NCAA patients meeting the inclusion criteria were included in the study. The primary end point was the success rate for DCS (length of stay less than 12 hours) in the intention-to-treat population (all NCAA) and in the per-protocol population (no pre- or perioperative exclusion criteria). The secondary end points were morbidity, DCS quality criteria, predictive factors for successful DCS, patient satisfaction, quality of life, and reasons for pre- or perioperative exclusion. A subgroup of patients discharged to home the day before operation was also analyzed. A total of 240 patients were included. The success rate of DCS was 31.5% in the intention-to-treat population and 91.5% in the per-protocol population. The rates of unplanned consultations, hospitalization, and reoperation were 13%, 4%, and 1%, respectively. An analysis of the reasons for DCS exclusion showed that 73% could have been modified. For the 68 patients discharged to home on the day before operation, the DCS success rate was 91%. Day case surgery is feasible in NCAA. A critical analysis of the reasons for exclusion from DCS showed that it should be possible to dramatically increase the eligible population. Copyright © 2016 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

  3. Case Study - Alpha

    Directory of Open Access Journals (Sweden)

    Stephen Leybourne

    2016-11-01

    Full Text Available This case study was developed from an actual scenario by Dr. Steve Leybourne of Boston University.  The case documents the historical evolution of an organization, and has been used successfully in courses dealing with organizational and cultural change, and the utilization of ‘soft skills’ in project-based management. This is a short case, ideal for classroom use and discussion.  The issues are easily accessible to students, and there is a single wide ranging question that allows for the inclusion of many issues surrounding strategic decision-making, and behavioural and cultural change. Alpha was one of the earlier companies in the USA to invest in large, edge-of-town superstores, with plentiful free vehicle parking, selling food and related household products. Alpha was created in the 1950s as a subsidiary of a major publicly quoted retail group.  It started business by opening a string of very large discount stores in converted industrial and warehouse premises in the south of the United States. In the early days shoppers were offered a limited range of very competitively priced products. When Alpha went public in 1981 it was the fourth largest food retailer in the US, selling an ever-widening range of food and non-food products.  Its success continued to be based on high volume, low margins and good value for money, under the slogan of ‘Alpha Price.’

  4. Feasibility study for the redesign of MDOT's pavement management systems software.

    Science.gov (United States)

    2011-04-01

    In August of 2006 the Mississippi Department of Transportation (MDOT) initiated State Study No. 191, entitled Feasibility : Study for the Redesign of MDOTs Pavement Management System (PMS) Software. At the initiation of this study, the : Dep...

  5. Development of a radiochemical sensor. Part I: Feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Tarancon, A. [Departament de Quimica Analitica, Facultat de Quimica, Universitat de Barcelona, C/ Marti Franques 1, 08028 Barcelona (Spain); Garcia, J.F. [Departament de Pintura, Facultat de Belles Arts, Universitat de Barcelona, C/ Pau Gargallo 4, 08028 Barcelona (Spain)]. E-mail: jfgarcia@apolo.qui.ub.es; Rauret, G. [Departament de Quimica Analitica, Facultat de Quimica, Universitat de Barcelona, C/ Marti Franques 1, 08028 Barcelona (Spain)

    2005-05-04

    The evolution of nuclear activities and criteria for radiation protection have led to a continuous increase in measures to monitor and control the environment and therefore in the number of determinations required for such purposes. Classical analytical procedures are time-consuming, labor-intense and generate a large amount of waste. The alternative use of sensors for such determinations has seen very limited development. The present study focuses on the evaluation of the behavior of a prototype radiochemical sensor for liquid effluents. The sensor is based on a receptor made of a plastic scintillator and is capable of continuous, on-time and accurate remote quantification of the activity of alpha, beta and beta-gamma emitters. Low-level active solutions of {sup 90}Sr/{sup 90}Y, {sup 238}Pu, {sup 134}Cs and {sup 60}Co in matrices of groundwater, seawater and drinking water were quantified with prediction errors lower than 10% in most cases. The study also yields information about light generation and transmission and transductor configuration that will be useful in the design of future versions of this sensor.

  6. NOx trade. Case studies

    International Nuclear Information System (INIS)

    Jantzen, J.

    2002-01-01

    Some of the questions with respect to the trade of nitrogen oxides that businesses in the Netherlands have to deal with are dealt with: should a business buy or sell rights for NOx emission; which measures must be taken to reduce NOx emission; how much must be invested; and how to deal with uncertainties with regard to prices. Simulations were carried out with the MOSES model to find the answers to those questions. Results of some case studies are presented, focusing on the chemical sector in the Netherlands. Finally, the financial (dis)advantages of NOx trade and the related uncertainties for a single enterprise are discussed [nl

  7. OBSESSIONS: CASE REPORT STUDY

    Directory of Open Access Journals (Sweden)

    Miloš Židanik

    2004-01-01

    Full Text Available Background. Obsessions are one of the most refractory psychiatric disorders. The therapeutic guidelines include a psychopharmacotherapy and the use of behavioural and supportive psychotherapy.Methods. This case report study presents a patient with a homicide obsessions at the forefront and narcissistic personality disorder in background. The use of analytical oriented psychotherapy, which helped to resolve axis-1 symptoms, is described.Conclusions. In the therapy of patients it is important to have the knowledge about the national therapeutic guidelines and critical distance toward them as well. Which therapy to use should be decided by the individual patient’s needs.

  8. Training Corrective Maintenance Performance on Electronic Equipment with CAI Terminals: I. A Feasibility Study.

    Science.gov (United States)

    Rigney, Joseph W.

    A report is given of a feasibility study in which several possible relationships between student, computer terminal, and electronic equipment were considered. The simplest of these configurations was set up and examined in terms of its feasibility for teaching the performance of fault localization on a Navy transceiver. An instructional program…

  9. FIRST FEASIBILITY STUDY FOR EXL WITH PROTOTYPE DETECTORS AT THE ESR AND DETECTOR SIMULATIONS

    NARCIS (Netherlands)

    Kalantar-Nayestanaki, N.; Moeini, H.; Mahjour-Shafiei, M.; Aksouh, F.; Beckert, K.; Beller, P.; Boretzky, K.; Chatillon, A.; Corsi, A.; Egelhof, P.; Emling, H.; Ickert, G.; Ilieva, S.; Kozhuharov, C.; Le Bleis, T.; Le Xuang, X. C.; Litvinov, Y.; Mahata, K.; Meier, J. P.; Nolden, F.; Popp, U.; Simon, H.; Steck, M.; Stoehlker, T.; Weick, H.; Zalite, A.; Kiselev, O.; Jourdan, J.; Kiselev, D.; Werthmueller, D.; Paschalis, S.

    This contribution presents some results from the first feasibility measurement performed at GSI using a 350 MeV/nucleon (136)Xe beam and a Hydrogen gas-jet target. In this feasibility study, one element of every possible detection part of the future EXL detection system was investigated. In

  10. Relationship between indoor radon and lung cancer: a study of feasibility of an epidemiological study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Rasmussen, S.; Neuberg, D.; DuMouchel, W.; Kleitman, D.; Chernoff, H.

    1981-01-01

    This report describes a study to assess the feasibility of an epidemiologic investigation of the relationship between residential radon exposure and lung cancer. Field measurements of residential radon levels in the State of Maine are described. Using these radon measurements and BEIR, 1980 risk assessments, it is estimated that at most 10% of lung cancers in Maine can be considered attributable to residential radon exposure. Calculations are made of sample sizes necessary for a case-control study of radon and lung cancer, for several levels of radon and smoking health effects. The effects of misclassification of exposure variables on the probability of detecting a radon health effect are discussed. A comparison is made of three different mathematical models which could be used for sample size estimation. Dollar cost estimates are given for conducting an epidemiologic case-control study of the relationship between residential radon exposure and lung cancer.

  11. Relationship between indoor radon and lung cancer: a study of feasibility of an epidemiological study. Final report

    International Nuclear Information System (INIS)

    Rasmussen, S.; Neuberg, D.; DuMouchel, W.; Kleitman, D.; Chernoff, H.

    1981-01-01

    This report describes a study to assess the feasibility of an epidemiologic investigation of the relationship between residential radon exposure and lung cancer. Field measurements of residential radon levels in the State of Maine are described. Using these radon measurements and BEIR, 1980 risk assessments, it is estimated that at most 10% of lung cancers in Maine can be considered attributable to residential radon exposure. Calculations are made of sample sizes necessary for a case-control study of radon and lung cancer, for several levels of radon and smoking health effects. The effects of misclassification of exposure variables on the probability of detecting a radon health effect are discussed. A comparison is made of three different mathematical models which could be used for sample size estimation. Dollar cost estimates are given for conducting an epidemiologic case-control study of the relationship between residential radon exposure and lung cancer

  12. Feasibility study for power generation using off- grid energy system from micro hydro-PV-diesel generator-battery for rural area of Ethiopia: The case of Melkey Hera village, Western Ethiopia

    Directory of Open Access Journals (Sweden)

    Tilahun Nigussie

    2017-07-01

    Full Text Available Electricity supply in Ethiopia is extremely antiquated. Most of the remote rural areas of Ethiopia are not yet electrified. Electrifying these remote areas by extending grid system is difficult and costly. Melkey Hera village is one of a rural community situated in western Ethiopia. In this village, extension of the grid is not yet practical. As the current international trend in rural electrification is to utilize renewable energy resources; solar, wind, biomass, and micro hydro power systems can be seen as alternatives. Therefore, the target of this paper is to investigate the viability of a micro hydro, Photo Voltaic (PV and Diesel Generator-battery hybrid power system options to come up with the best techno-economic and optimum configuration for supplying electricity to this village. The study was performed by an assessment of the predicted village energy demand, the available renewable energy resources, and then using the software called HOMER. The best hybrid system type was described and the optimization of the system configuration was also done. Furthermore, through the simulation of different configuration of the supply system, the optimal mini-grid hybrid system design was established to combine hydro, solar PV, battery energy storage and diesel generator. This system demonstrated to be more reliable in operation, and the most cost-effective for the required level of service. The role of energy storage in system operation also demonstrated to offer additional operational advantages in-terms of reliability and cost savings. Overall, the design results show that the majority of energy obtained from hydropower, which accounts 79%, the PV module covers 20%, and diesel generator is only 1% of the total load consumption. The obtained hybrid system is cost competitive with $\\$$0.133/kWh, which is somewhat good to satisfy the community needs. However, this is more than current energy price in Ethiopia which $\\$$0.06/kWh. If due-merit given

  13. Some comments on the feasibility of an epidemiological study on incidence of lung cancer due to exposure to radon daughters

    International Nuclear Information System (INIS)

    Elsasser, U.

    1988-01-01

    For two different designs of a study - cohort and case control study - estimates of required sample size have been made on the basis of lung cancer risk assessment data for exposure to radon and radon daughters. The estimates have shown that a cohort study is not feasible for reasons of unjustifiably high requirements. A case control study, however, may contribute to clarifying the lung cancer risk, especially if the basic overall entity is limited to the population group of over 50 years of age. (orig.) [de

  14. Feasibility study on standardization of 131I dose in hyperthyrodisom treatment

    International Nuclear Information System (INIS)

    Tang Yi

    2011-01-01

    To explore feasibility of standardization of 131 I dose in Graves' hyperthyroidism treatment, the data of 681 Graves' disease cases treated with 131 I was retrospective studied. The software was developed to re-calculate the 131 I doses for the patients and compared with original doses given by traditional method. 313 patients with complete information were taken and divided to three groups base on the remedial effect, Cured Group (123 patients), Uncured Group (125 patients) and Hypothyroid Group (65 patients). The results showed that there was no statistically significant difference between the 131 I dose for Graves' hyperthyroidism treatment calculated by two methods (P>0.05). There was obviously statistically significant difference in hypothyroid Group (P 131 I calculated by software method (174.27 MBq) was less than that of traditional method (190.18 MBq). In uncured group, there was still obviously statistically significant difference (P 131 I calculated by software method (187.22 MBq) was more than that of the traditional method (169.46 MBq). In cured group, there was no statistically significant difference (P>0.005), the mean dose of 131 I calculated by software method (185 MBq) was slightly smaller than that of the traditional method(192.03 MBq). The results indicate the calculation of standard 131 I dose for Graves' hyperthyroidism treatment by software developed in this study is feasible. (authors)

  15. Feasibility Study of Grid Connected PV-Biomass Integrated Energy System in Egypt

    Science.gov (United States)

    Barakat, Shimaa; Samy, M. M.; Eteiba, Magdy B.; Wahba, Wael Ismael

    2016-10-01

    The aim of this paper is to present a feasibility study of a grid connected photovoltaic (PV) and biomass Integrated renewable energy (IRE) system providing electricity to rural areas in the Beni Suef governorate, Egypt. The system load of the village is analyzed through the environmental and economic aspects. The model has been designed to provide an optimal system configuration based on daily data for energy availability and demands. A case study area, Monshaet Taher village (29° 1' 17.0718"N, 30° 52' 17.04"E) is identified for economic feasibility in this paper. HOMER optimization model plan imputed from total daily load demand, 2,340 kWh/day for current energy consuming of 223 households with Annual Average Insolation Incident on a Horizontal Surface of 5.79 (kWh/m2/day) and average biomass supplying 25 tons / day. It is found that a grid connected PV-biomass IRE system is an effective way of emissions reduction and it does not increase the investment of the energy system.

  16. Feasibility study on recovering hydrogen energy from industrial wastewater

    International Nuclear Information System (INIS)

    Ming Der Bai; Chia-Jung Hsiao

    2006-01-01

    Three wastewater obtained from different industries were evaluated for the feasibility of hydrogen fermentation. Because of the various components of the wastewater, the characteristics of the hydrogen accumulation were different. Several stages with different hydrogen producing rate were observed during the batch hydrogen fermentation of each wastewater. The obvious hydrogen consumption was observed in the last phase of hydrogen fermentation of the wastewater from the winery. It is similar to the reported hydrogen fermentation characteristic of starch. The wastewater coming from the fructose manufactory has the greatest hydrogen potential nearly 150 L-H 2 /kg-COD. The wastewater from food industry has the lower hydrogen potential of 65 L-H 2 /kg-COD. Some of its compounds were not suitable for hydrogen production. The lowest hydrogen potential was observed in the fermentation of the wastewater from the winery, because hydrogen consumption affects the hydrogen recovery from the wastewater from winery. (authors)

  17. Coaching at the Building Site – A Feasibility Study

    DEFF Research Database (Denmark)

    Koch, Christian; Alsdorf, Morten; Sander, Dag

    2006-01-01

    successfully at a building site, in certain specific situations. The feeling of security is important for the focus persons at the building site and is best obtained in the open air. The way the leader acts towards the employee/focus person is decisive. Consciousness and responsibility is developed......Coaching has become widely used in business, and is well described. However it is rarely used in construction. This makes a contrast to the poor performance of site interaction, leading to a vast amount of reported cooperation and coordination problems. This paper investigates the feasibility...... observations in a building site operating with lean construction, where the managers did not use coaching consciously in their interaction with employees. 29 participant observations of five of the managers at the building site were carried out, at individual- and group meetings. Coaching can be used...

  18. Feasibility study on emergency passive habitability systems of SPWR

    International Nuclear Information System (INIS)

    Obata, H.; Tabata, H.; Urakami, M.; Naito, T.

    2000-01-01

    The major characteristic of the Simplified Pressurized Water Reactor (SPWR) is that safety systems for the emergency core cooling and the core decay heat removal functions are achieved by passive equipment. The AP600 developed in the U.S adopts passive emergency habitability system for the main control room (MCR) and the electrical equipment rooms (EER) by using the concrete of the structures as a heat sink. For the SPWR, alternative natural circulation cooling systems have been investigated: for MCR cooling, a cold water reservoir is used as heat sink; for EER cooling, outside air is instead employed. The distribution of the air-velocity and temperature in those rooms were calculated by using a three-dimensional thermal fluid analysis code. The authors verified the conceptual feasibility of these systems as the emergency passive habitability systems in the SPWR. (author)

  19. Feasibility study to establish a new value chain

    DEFF Research Database (Denmark)

    Ingrid Herman, Marie; Thai, Thi Minh

    Since the 90s value chain (VC) approaches have received considerable attention by governments and development agencies for poverty reduction and strengthening the private sector. VC analysis has been used for developing intervention strategies to upgrade existing or to establish new VCs. Despite...... and starting to valorize New Caledonian horticulture on international markets. Once goals were understood, four interrelated analyses were conducted continuously: enabling environment, productivity, structuration, and feasibility analysis. In the enabling environment, analysis of market, institution......, and infrastructure highlighted high demands for the species Sticherus flabellatus, well-maintained roads, and legal voids concerning wild harvesting. The productivity analysis on resource availability and harvesting potential pointed out randomness of the resource and its quality, and the rarity of Sticherus...

  20. Feasibility study of CANDU-9 fuel handling system

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Jeong Ki; Jo, C. H.; Kim, H. M.

    1996-12-0