WorldWideScience

Sample records for carbonyl chloride

  1. Oxalyl chloride as a practical carbon monoxide source for carbonylation reactions

    DEFF Research Database (Denmark)

    Hansen, Steffen V F; Ulven, Trond

    2015-01-01

    A method for generation of high-quality carbon monoxide by decomposition of oxalyl chloride in an aqueous hydroxide solution is described. The usefulness of the method is demonstrated in the synthesis of heterocycles and for hydroxy-, alkoxy-, amino-, and reductive carbonylation reactions, in sev...

  2. THE COMPATIBILITY OF BLENDS OF POLY(VINYL CHLORIDE) OR CHLORINATED POLY(VINYL CHLORIDE) WITH POLY(METHYL METHACRYLATE)

    Institute of Scientific and Technical Information of China (English)

    WANG Qingguo; CHENG Rongshi

    1988-01-01

    IR spectral shifts of carbonyl vibrational absorption for ethyl acetate, which acts analogically as the structural unit of poly(methyl methacrylate), in cyclohexane, chloroform, chlorinated paraffins, poly(vinyl chloride) and chlorinated poly(vinyl chloride) were measured. The results suggest that there are specific interactions between the carbonyl groups and the chlorinated hydrocarbons which could be responsible for the apparent compatibility of poly(vinyl chloride) -poly(methyl methacrylate) and chlorinated poly(vinyl chloride) -poly(methyl methacrylate) blends. Additionally, the effects of the preparation mode of blend films on phase separation and observed compatibility are discussed.

  3. Validation of protein carbonyl measurement

    DEFF Research Database (Denmark)

    Augustyniak, Edyta; Adam, Aisha; Wojdyla, Katarzyna;

    2015-01-01

    Protein carbonyls are widely analysed as a measure of protein oxidation. Several different methods exist for their determination. A previous study had described orders of magnitude variance that existed when protein carbonyls were analysed in a single laboratory by ELISA using different commercial...

  4. The Optimization of Technological Parameters in the Synthesis of Pheny-Lacetic Acid in the Normal Pressure Carbonylation of Benzyl Chloride%氯化苄常压羰基化合成苯乙酸的最佳工艺研究

    Institute of Scientific and Technical Information of China (English)

    邱祖民; 何运兵; 郑典模; 刘府芳

    2005-01-01

    采用L18(36×61)正交实验,考察了反应温度、氢氧化钠溶液浓度、油水体积比、十二烷基苯磺酸钠用量、Pd(PPh3)2Cl2用量、PPh3用量、溶剂(叔丁醇、正丁醇、正庚烷)等因素对氯化苄单羰基化合成苯乙酸的影响,得出其较佳反应条件为以正丁醇为反应溶剂,不加表面活性剂,加0.24 g PPh3、0.4g Pd(PPh3)2Cl2、20 mL氯化苄、55 mL正丁醇、75 mL 3.5 mol/L的NaOH水溶液,在50℃下反应3 h,此时苯乙酸的产率可达99.0%;另外,还探讨了反应体系中空气与苯乙酸的引入对反应的影响,结果表明:反应体系中空气的存在以及循环油相反应液中苯乙酸的带入对反应的速率、催化剂的稳定性及性能、苯乙酸的产率影响很大.%The influences of the factors affecting the synthesis of phenylacetic acid in the carbonylation of benzyl chloride are studied by means of an orthogonal experiment[L18(36×61)] in this article. These factors include reaction temperature, the concentration of sodium hydrate liquor, the ratio of organic phase volume to aqueous phase volume (Vo:Vw), the amount of sodium dodecyl benzene sulfonate, the amount of Pd(PPh3)2Cl2 and PPh3, the solvent(primarily tert-butyl alcohol, n-butyl alcohol, n-heptane) etc. The optimum reaction conditions have been concluded: n-butyl alcohol was used as the solvent, with one-time pour of 0.24g PPh3, 0.4g Pd(PPh3)2Cl2, 20 mL benzyl chloride, 55 mL n-butyl alcohol and 75 mL sodium hydrate liquor of 3.5 mol/L but no surfactant, and the reaction was carried out at 50℃for 3 hours. The so-obtained yield of phenylacetic acid can be up to 99%. In addition, the influences of the presence of phenylacetic acid and air in the reaction system are also studied. The result shows that the presence of air in the system and the entrainment of phenylacetic acid in the circulating organic phase have great influence on reaction rate, the stability and performance of catalyst and the yield of phenylacetic

  5. Radical carbonylations using a continuous microflow system

    Directory of Open Access Journals (Sweden)

    Takahide Fukuyama

    2009-07-01

    Full Text Available Radical-based carbonylation reactions of alkyl halides were conducted in a microflow reactor under pressurized carbon monoxide gas. Good to excellent yields of carbonylated products were obtained via radical formylation, carbonylative cyclization and three-component coupling reactions, using tributyltin hydride or TTMSS as a radical mediator.

  6. Kinetics of the Double Carbonylation of Benzylchloride

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    It is a multi-phase-catalyzed reaction to produce calcium phenylpyruvate by double carbonylation of benzylchloride. Based on the analysis of the reaction mechanism, a kinetic model of the carbonylation reaction was obtained. The model was verified through experiments in which the diffusion effect was neglected with the appropriate operation manner. But it is inevitable that the carbonylation process is controlled by diffusion as the autoclave scaling up.

  7. An Efficient One-pot Synthesis of β-Amino/β-Acetamido Car-bonyl Compounds via ZrCl4-catalyzed Mannich-type Reaction

    Institute of Scientific and Technical Information of China (English)

    SANJEEVA REDDY,Cherkupally; PURNACHANDRA REDDY,Gurrala

    2008-01-01

    Zirconium(IV) chloride catalyzed efficient one-pot synthesis of β-amino/β-acetamido carbonyl compounds at room temperature is described. In the presence of ZrCl4, the three-component Mannich-type reaction via a variety of in situ generated aldimines, with various ketones, aromatic aldehydes and aromatic amines in ethanol, led to the formation of β-amino carbonyl compounds and the four-component Mannich-type reaction of aromatic aldehydes with various ketones, acetonitrile and acetyl chloride resulted in the corresponding β-acetamido carbonyl com-pounds in high to excellent yields. This methodology has also been applied towards the synthesis of dimeric β-amino/β-acetamido carbonyl compounds.

  8. Surface decorated platinum carbonyl clusters

    Science.gov (United States)

    Ciabatti, Iacopo; Femoni, Cristina; Iapalucci, Maria Carmela; Longoni, Giuliano; Zacchini, Stefano; Zarra, Salvatore

    2012-06-01

    Four molecular Pt-carbonyl clusters decorated by Cd-Br fragments, i.e., [Pt13(CO)12{Cd5(μ-Br)5Br2(dmf)3}2]2- (1), [Pt19(CO)17{Cd5(μ-Br)5Br3(Me2CO)2}{Cd5(μ-Br)5Br(Me2CO)4}]2- (2), [H2Pt26(CO)20(CdBr)12]8- (3) and [H4Pt26(CO)20(CdBr)12(PtBr)x]6- (4) (x = 0-2), have been obtained from the reactions between [Pt3n(CO)6n]2- (n = 2-6) and CdBr2.H2O in dmf at 120 °C. The structures of these molecular clusters with diameters of 1.5-2 nm have been determined by X-ray crystallography. Both 1 and 2 are composed of icosahedral or bis-icosahedral Pt-CO cores decorated on the surface by Cd-Br motifs, whereas 3 and 4 display a cubic close packed Pt26Cd12 metal frame decorated by CO and Br ligands. An oversimplified and unifying approach to interpret the electron count of these surface decorated platinum carbonyl clusters is suggested, and extended to other low-valent organometallic clusters and Au-thiolate nanoclusters.Four molecular Pt-carbonyl clusters decorated by Cd-Br fragments, i.e., [Pt13(CO)12{Cd5(μ-Br)5Br2(dmf)3}2]2- (1), [Pt19(CO)17{Cd5(μ-Br)5Br3(Me2CO)2}{Cd5(μ-Br)5Br(Me2CO)4}]2- (2), [H2Pt26(CO)20(CdBr)12]8- (3) and [H4Pt26(CO)20(CdBr)12(PtBr)x]6- (4) (x = 0-2), have been obtained from the reactions between [Pt3n(CO)6n]2- (n = 2-6) and CdBr2.H2O in dmf at 120 °C. The structures of these molecular clusters with diameters of 1.5-2 nm have been determined by X-ray crystallography. Both 1 and 2 are composed of icosahedral or bis-icosahedral Pt-CO cores decorated on the surface by Cd-Br motifs, whereas 3 and 4 display a cubic close packed Pt26Cd12 metal frame decorated by CO and Br ligands. An oversimplified and unifying approach to interpret the electron count of these surface decorated platinum carbonyl clusters is suggested, and extended to other low-valent organometallic clusters and Au-thiolate nanoclusters. CCDC 867747 and 867748. For crystallographic data in CIF or other electronic format see DOI: 10.1039/c2nr30400g

  9. Trifluoromethylation of Carbonyl Compounds with Sodium Trifluoroacetate

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    In the presence of copper (Ⅰ) halide as catalyst, a variety of carbonyl compounds could be trifluoromethylated with sodium trifluoroacetate to give the corresponding alcohols in moderate to high yields.

  10. Stratospheric carbonyl sulfide (OCS) burden

    Science.gov (United States)

    Kloss, Corinna; Walker, Kaley A.; Deshler, Terry; von Hobe, Marc

    2015-04-01

    An estimation of the global stratospheric burden of carbonyl sulfide (OCS) calculated using satellite based measurements from the Atmospheric Chemistry Experiment - Fourier Transform Spectrometer (ACE-FTS) will be presented. OCS is the most abundant sulfur containing gas in the atmosphere in the absence of volcanic eruptions. With a long lifetime of 2-6 years it reaches the stratosphere where it is photolyzed and the sulfur oxidized and condensed to aerosols, contributing to the stratospheric aerosol layer. The aerosol layer is the one factor of the middle-atmosphere with a direct impact on the Earth's climate by scattering incoming solar radiation back to space. Therefore it is crucial to understand and estimate the different processes and abundances of the species contributing to the aerosol layer. However, the exact amount of OCS in the stratosphere has not been quantified yet. A study on the OCS mixing ratio distribution based on ACE-FTS data has already been made by Barkley et al. (2008), also giving an estimation for the total atmospheric OCS mass. ACE-FTS is an infrared solar occultation spectrometer providing high- resolution profile observations since 2004. In the scope of this work the focus lies on the stratospheric OCS burden, calculated by integrating the ACE profiles. A global overview on the stratospheric OCS amount in the past and present based on the ACE data as well as a look at regional and seasonal variability will be given. Furthermore, the results of this work will be useful for further studies on OCS fluxes and lifetimes, and in quantifying the contribution of OCS to the global stratospheric sulfur burden. Barkley et al., 2008, Geophys. Res. Lett., 35, L14810.

  11. N-(2-Benzoylethylpropan-2-aminium chloride

    Directory of Open Access Journals (Sweden)

    Abdullah Aydın

    2012-09-01

    Full Text Available In the title salt, C12H18NO+·Cl−, N—H...Cl interactions between the free chloride anions and the organic cations connect the molecules into hydrogen-bond dimers, forming a R22(8 motif. The dimers are linked by C—H...O hydrogen bonds into chains extending along [301]. The carbonyl group is co-planar with the phenyl ring [C—C—C=O torsion angle = −3.3 (7°]. The side chain has an E conformation.

  12. A catalyst for the carbonylation of methanol to acetic acid in gaseous phase

    Institute of Scientific and Technical Information of China (English)

    潘平来; 柳忠阳; 朱长城; 袁国卿

    1996-01-01

    A novel Rh/Ys catalyst for the carbonylation of methanol to acetic acid in gaseous phase is reported. The porous carbon beads (Ys) prepared from the carbonation of poly(vinylidene chloride) were used as the support. This catalyst has a specific surface area of 1 000 m2/g, high mechanical strength and thermal stability. The average diameter of the pore is in the range of 0.8 - 1.2nm. Experimental evidence showed that this catalyst was of high activity and selectivity, which could compare to those of the homogeneous catalyst from Monsanto. The catalytic rate could get to 900 g AcOH/g Rh·h during the carbonylation of methanol to acetic acid. The fine spreading of Ph over the Ys surface is the key factor for the activity.

  13. Millimeter wave spectra of carbonyl cyanide ⋆

    Science.gov (United States)

    Bteich, S.B.; Tercero, B.; Cernicharo, J.; Motiyenko, R.A.; Margulès, L.; Guillemin, J.-C.

    2016-01-01

    Context More than 30 cyanide derivatives of simple organic molecules have been detected in the interstellar medium, but only one dicarbonitrile has been found and that very recently. There is still a lack of high-resolution spectroscopic data particularly for dinitriles derivatives. The carbonyl cyanide molecule is a new and interesting candidate for astrophysical detection. It could be formed by the reaction of CO and CN radicals, or by substitution of the hydrogen atom by a cyano group in cyanoformaldehyde, HC(=O)CN, that has already been detected in the interstellar medium. Aims The available data on the rotational spectrum of carbonyl cyanide is limited in terms of quantum number values and frequency range, and does not allow accurate extrapolation of the spectrum into the millimeter-wave range. To provide a firm basis for astrophysical detection of carbonyl cyanide we studied its millimeter-wave spectrum. Methods The rotational spectrum of carbonyl cyanide was measured in the frequency range 152 - 308 GHz and analyzed using Watson’s A- and S-reduction Hamiltonians. Results The ground and first excited state of v5 vibrational mode were assigned and analyzed. More than 1100 distinct frequency lines of the ground state were fitted to produce an accurate set of rotational and centrifugal distortion constants up to the eighth order. The frequency predictions based on these constants should be accurate enough for astrophysical searches in the frequency range up to 500 GHz and for transition involving energy levels with J ≤ 100 and Ka ≤ 42. Based on the results we searched for interstellar carbonyl cyanide in available observational data without success. Thus, we derived upper limits to its column density in different sources. PMID:27738349

  14. Synthesis, structural and vibrational properties of 1-(adamantane-1-carbonyl)-3-halophenyl thioureas

    Science.gov (United States)

    Saeed, Aamer; Erben, Mauricio F.; Bolte, Michael

    2013-02-01

    1-(Adamantane-1-carbonyl)-3-(2,4-dichlorophenyl)thiourea (1) and 1-(adamantane-1-carbonyl)-3-(2-bromo-4,6-difluorophenyl)thiourea (2) were synthesized by the reaction of adamantane-1-carbonyl chloride with ammonium thiocyanate to afford the adamantane-1-carbonylisothiocyanate in situ followed by treatment with suitable halogenated anilines. The structures of the products were established by elemental analyses, Fourier transform infrared spectroscopy (FTIR), 1H, 13C nuclear magnetic resonance (NMR), mass spectroscopy and single crystal X-ray diffraction study. Bond lengths and angles show the usual values. All of three condensed cyclohexane rings of the adamantane residues adopt the usual chair conformation. The molecular conformation of 1 and 2 is stabilized by an intramolecular (Nsbnd H⋯Odbnd C) hydrogen bond which forms a pseudo-six-membered ring. Structural features have been complemented with the joint analysis of the FTIR and FT-Raman spectra along with quantum chemical calculations at the B3LYP/6-311++G** level.

  15. Carbonyl compounds generated from electronic cigarettes.

    Science.gov (United States)

    Bekki, Kanae; Uchiyama, Shigehisa; Ohta, Kazushi; Inaba, Yohei; Nakagome, Hideki; Kunugita, Naoki

    2014-10-28

    Electronic cigarettes (e-cigarettes) are advertised as being safer than tobacco cigarettes products as the chemical compounds inhaled from e-cigarettes are believed to be fewer and less toxic than those from tobacco cigarettes. Therefore, continuous careful monitoring and risk management of e-cigarettes should be implemented, with the aim of protecting and promoting public health worldwide. Moreover, basic scientific data are required for the regulation of e-cigarette. To date, there have been reports of many hazardous chemical compounds generated from e-cigarettes, particularly carbonyl compounds such as formaldehyde, acetaldehyde, acrolein, and glyoxal, which are often found in e-cigarette aerosols. These carbonyl compounds are incidentally generated by the oxidation of e-liquid (liquid in e-cigarette; glycerol and glycols) when the liquid comes in contact with the heated nichrome wire. The compositions and concentrations of these compounds vary depending on the type of e-liquid and the battery voltage. In some cases, extremely high concentrations of these carbonyl compounds are generated, and may contribute to various health effects. Suppliers, risk management organizations, and users of e-cigarettes should be aware of this phenomenon.

  16. Carbonyl Compounds Generated from Electronic Cigarettes

    Directory of Open Access Journals (Sweden)

    Kanae Bekki

    2014-10-01

    Full Text Available Electronic cigarettes (e-cigarettes are advertised as being safer than tobacco cigarettes products as the chemical compounds inhaled from e-cigarettes are believed to be fewer and less toxic than those from tobacco cigarettes. Therefore, continuous careful monitoring and risk management of e-cigarettes should be implemented, with the aim of protecting and promoting public health worldwide. Moreover, basic scientific data are required for the regulation of e-cigarette. To date, there have been reports of many hazardous chemical compounds generated from e-cigarettes, particularly carbonyl compounds such as formaldehyde, acetaldehyde, acrolein, and glyoxal, which are often found in e-cigarette aerosols. These carbonyl compounds are incidentally generated by the oxidation of e-liquid (liquid in e-cigarette; glycerol and glycols when the liquid comes in contact with the heated nichrome wire. The compositions and concentrations of these compounds vary depending on the type of e-liquid and the battery voltage. In some cases, extremely high concentrations of these carbonyl compounds are generated, and may contribute to various health effects. Suppliers, risk management organizations, and users of e-cigarettes should be aware of this phenomenon.

  17. Magnetorheological characterisation of carbonyl iron based suspension

    Directory of Open Access Journals (Sweden)

    M. Kciuk

    2009-04-01

    Full Text Available Purpose: The main aim of this article was to present the investigation results of magnetorheological fluids (MR composed of carbonyl iron (CI particles and analyse their flow behaviour in terms of the internal structure formation by a control of applied external magnetic field. The morphology, magnetic properties, sedimentation stability, and magnetorheological properties of the examined MR fluids were studied.Design/methodology/approach: Model MR fluid was prepared using silicone oil OKS 1050 mixed with carbonyl iron powder CI. Furthermore, to reduce sedimentation Aerosil 200 was added as stabilizers. In the purpose to determine the properties of the analyzed fluids the sedimentation and dynamic viscosity were investigated.Findings: Dynamic viscosity of investigated magnetorheological fluids rapidly and reversibly change in response to the applied external magnetic field. Moreover added particles of fumed silica inhibited sedimentation of carbonyl iron particles.Research limitations/implications: MR fluids with excellent properties can be applied in various fields of civil engineering, safety engineering, transportation and life science. They offer an outstanding capability of active control of mechanical properties. But there are no systematic published studies of factors affecting the durability of MR fluids and devices. There is very little information on the effects of exposing different MR fluids to temperature, for this reasons further efforts are needed in order to obtain even better results.Originality/value: The investigation results are reliable and could be very useful both for designers and the practitioners of many branches of industry.

  18. Millimeter wave spectra of carbonyl cyanide

    Science.gov (United States)

    Bteich, S. B.; Tercero, B.; Cernicharo, J.; Motiyenko, R. A.; Margulès, L.; Guillemin, J.-C.

    2016-07-01

    Context. More than 30 cyanide derivatives of simple organic molecules have been detected in the interstellar medium, but only one dicarbonitrile has been found and that very recently. There is still a lack of high-resolution spectroscopic data particularly for dinitriles derivatives. The carbonyl cyanide molecule is a new and interesting candidate for astrophysical detection. It could be formed by the reaction of CO and CN radicals, or by substitution of the hydrogen atom by a cyano group in cyanoformaldehyde, HC(=O)CN, that has already been detected in the interstellar medium. Aims: The available data on the rotational spectrum of carbonyl cyanide is limited in terms of quantum number values and frequency range, and does not allow accurate extrapolation of the spectrum into the millimeter-wave range. To provide a firm basis for astrophysical detection of carbonyl cyanide we studied its millimeter-wave spectrum. Methods: The rotational spectrum of carbonyl cyanide was measured in the frequency range 152-308 GHz and analyzed using Watson's A- and S-reduction Hamiltonians. Results: The ground and first excited state of v5 vibrational mode were assigned and analyzed. More than 1100 distinct frequency lines of the ground state were fitted to produce an accurate set of rotational and centrifugal distortion constants up to the eighth order. The frequency predictions based on these constants should be accurate enough for astrophysical searches in the frequency range up to 500 GHz and for transition involving energy levels with J ≤ 100 and Ka ≤ 42. Based on the results we searched for interstellar carbonyl cyanide in available observational data without success. Thus, we derived upper limits to its column density in different sources. This paper makes use of the following ALMA data: ADS/JAO.ALMA#2011.0.00009.SV. ALMA is a partnership of ESO (representing its member states), NSF (USA), and NINS (Japan) with NRC (Canada), NSC, and ASIAA (Taiwan), and KASI (Republic of

  19. Carbonyl Emissions from Gasoline and Diesel Motor Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Destaillats, Hugo; Jakober, Chris A.; Robert, Michael A.; Riddle, Sarah G.; Destaillats, Hugo; Charles, M. Judith; Green, Peter G.; Kleeman, Michael J.

    2007-12-01

    Carbonyls from gasoline powered light-duty vehicles (LDVs) and heavy-duty diesel powered vehicles (HDDVs) operated on chassis dynamometers were measured using an annular denuder-quartz filter-polyurethane foam sampler with O-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine derivatization and chromatography-mass spectrometry analyses. Two internal standards were utilized based on carbonyl recovery, 4-fluorobenzaldehyde forcarbonyls and 6-fluoro-4-chromanone for>_C8 compounds. Gas- and particle-phase emissions for 39 aliphatic and 20 aromatic carbonyls ranged from 0.1 ? 2000 ?g/L fuel for LDVs and 1.8 - 27000 mu g/L fuel for HDDVs. Gas-phase species accounted for 81-95percent of the total carbonyls from LDVs and 86-88percent from HDDVs. Particulate carbonyls emitted from a HDDV under realistic driving conditions were similar to concentrations measured in a diesel particulate matter (PM) standard reference material. Carbonyls accounted for 19percent of particulate organic carbon (POC) emissions from low-emission LDVs and 37percent of POC emissions from three-way catalyst equipped LDVs. This identifies carbonyls as one of the largest classes of compounds in LDV PM emissions. The carbonyl fraction of HDDV POC was lower, 3.3-3.9percent depending upon operational conditions. Partitioning analysis indicates the carbonyls had not achieved equilibrium between the gas- and particle-phase under the dilution factors of 126-584 used in the current study.

  20. Chemical modification of Sago starch by solvent less esterification with fatty acid chlorides

    International Nuclear Information System (INIS)

    Sago starch was chemically modified by esterification reaction with fatty acid chlorides to produce a non-polar sago ester in the absence of an organic solvent. The sago esters were prepared by first pretreatment of sago starch with excess formic acid at 90 degree Celsius for 40 minutes followed by acetylation with acid chloride (octanoyl and lauroyl chlorides). The maximum yields of 80 % and 73 % with the same degree of substitution (DS) of 1.2 for octanoate and lauroate sago esters were obtained respectively. The presence of ester carbonyl group in the FT-IR spectra of the ester products showed that the sago starch has been esterified. The intensities of carbonyl and methyl peaks were decreased with the increasing of DS. (author)

  1. Pattern of occurrence and occupancy of carbonylation sites in proteins

    DEFF Research Database (Denmark)

    Rao, R Shyama Prasad; Møller, Ian Max

    2011-01-01

    Proteins are targets for modification by reactive oxygen species, and carbonylation is an important irreversible modification that increases during oxidative stress. While information on protein carbonylation is accumulating, its pattern is not yet understood. We have made a meta-analysis of the ......Proteins are targets for modification by reactive oxygen species, and carbonylation is an important irreversible modification that increases during oxidative stress. While information on protein carbonylation is accumulating, its pattern is not yet understood. We have made a meta...... sites. Comparison of metal-catalyzed oxidation of two closely related proteins indicates that this type of carbonylation might not be very specific in proteins. Interestingly, carbonylated sites show a very strong tendency to cluster together in the protein primary sequence hinting at some sort...

  2. Acute inhalation toxicity of carbonyl sulfide

    Energy Technology Data Exchange (ETDEWEB)

    Benson, J.M.; Hahn, F.F.; Barr, E.B. [and others

    1995-12-01

    Carbonyl sulfide (COS), a colorless gas, is a side product of industrial procedures sure as coal hydrogenation and gasification. It is structurally related to and is a metabolite of carbon disulfide. COS is metabolized in the body by carbonic anhydrase to hydrogen sulfide (H{sub 2}S), which is thought to be responsible for COS toxicity. No threshold limit value for COS has been established. Results of these studies indicate COS (with an LC{sub 50} of 590 ppm) is slightly less acutely toxic than H{sub 2}S (LC{sub 50} of 440 ppm).

  3. Oxidation of Reduced Sulfur Species: Carbonyl Sulfide

    DEFF Research Database (Denmark)

    Glarborg, Peter; Marshall, Paul

    2013-01-01

    A detailed chemical kinetic model for oxidation of carbonyl sulfide (OCS) has been developed, based on a critical evaluation of data from the literature. The mechanism has been validated against experimental results from batch reactors, flow reactors, and shock tubes. The model predicts...... satisfactorily oxidation of OCS over a wide range of stoichiometric air–fuel ratios (0.5 ≤λ≤7.3), temperatures (450–1700 K), and pressures (0.02–3.0 atm) under dry conditions. The governing reaction mechanisms are outlined based on calculations with the kinetic model. The oxidation rate of OCS is controlled...

  4. Clinical Features of Schizophrenia With Enhanced Carbonyl Stress

    OpenAIRE

    Miyashita, Mitsuhiro; Arai, Makoto; Kobori, Akiko; Ichikawa, Tomoe; Toriumi, Kazuya; Niizato, Kazuhiro; Oshima, Kenichi; Okazaki, Yuji; Yoshikawa, Takeo; Amano, Naoji; Miyata, Toshio; Itokawa, Masanari

    2013-01-01

    Accumulating evidence suggests that advanced glycation end products, generated as a consequence of facilitated carbonyl stress, are implicated in the development of a variety of diseases. These diseases include neurodegenerative illnesses, such as Alzheimer disease. Pyridoxamine is one of the 3 forms of vitamin B6, and it acts by combating carbonyl stress and inhibiting the formation of AGEs. Depletion of pyridoxamine due to enhanced carbonyl stress eventually leads to a decrease in the other...

  5. Pollution survey of carbonyl compounds in train air

    Institute of Scientific and Technical Information of China (English)

    LU Hao; ZHU Lizhong

    2007-01-01

    The train iS an important vehicle in China,but its air quality has important impacts on passengers' health.In this work,pollution from carbonyl compounds was measured in the air of six trains.The obiectives of this work were to investigate carbonyl compound levels in selected air from trains,identify their emission sources,and assess the intake of carbonyl compounds for passengers.The methods for sampling and analyzing 10 carbonyl compounds such as formaldehyde,acetaldehyde,acrolein,acetone,propionalde hyde,crotonaldehyde,butyraldehyde,benzaldehyde,cyclo hexanone,and valeraldehyde in indoor air were proposed with the sampling efficiency,recovery,and detection limit being 92%-100%,91%-104%,and 0.26-0.82 ng/m3,respec tively.It was indicated that the total concentrations of carbonyl compounds were 0.159-0.2828 mg/m3 with the average concentration of 0.2330 mg/m3.The average concen trations of formaldehyde.acetaldehyde and acetone were 0.0922,0.0499,and 0.0580 mg/m3,accounting for 42.6%,21.4%.and 24.9% of the total concentrations of carbonyl compounds,respectively.The carbonyl compounds probably came from woodwork and cigarette smoking.The intake of carbonyl compounds for the passengers was approximately 0.043-0.076 mg/h.The carbonyl compounds in train air could be harmful to human health.

  6. Gas-phase chemistry of ruthenium and rhodium carbonyl complexes.

    Science.gov (United States)

    Cao, Shiwei; Wang, Yang; Qin, Zhi; Fan, Fangli; Haba, Hiromitsu; Komori, Yukiko; Wu, Xiaolei; Tan, Cunmin; Zhang, Xin

    2016-01-01

    Short-lived ruthenium and rhodium isotopes were produced from a (252)Cf spontaneous fission (SF) source. Their volatile carbonyl complexes were formed in gas-phase reactions in situ with the carbon-monoxide containing gas. A gas-jet system was employed to transport the volatile carbonyls from the recoil chamber to the chemical separation apparatus. The gas-phase chemical behaviors of these carbonyl complexes were studied using an online low temperature isothermal chromatography (IC) technique. Long IC columns made up of FEP Teflon were used to obtain the chemical information of the high-volatile Ru and Rh carbonyls. By excluding the influence of precursor effects, short-lived isotopes of (109-110)Ru and (111-112)Rh were used to represent the chemical behaviours of Ru and Rh carbonyls. Relative chemical yields of about 75% and 20% were measured for Ru(CO)5 and Rh(CO)4, respectively, relative to the yields of KCl aerosols transported in Ar gas. The adsorption enthalpies of ruthenium and rhodium carbonyl complexes on a Teflon surface were determined to be around ΔHads = -33(+1)(-2) kJ mol(-1) and -36(+2)(-1) kJ mol(-1), respectively, by fitting the breakthrough curves of the corresponding carbonyl complexes with a Monte Carlo simulation program. Different from Mo and Tc carbonyls, a small amount of oxygen gas was found to be not effective for the chemical yields of ruthenium and rhodium carbonyl complexes. The general chemical behaviors of short-lived carbonyl complexes of group VI-IX elements were discussed, which can be used in the future study on the gas-phase chemistry of superheavy elements - Bh, Hs, and Mt carbonyls. PMID:26573993

  7. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents experimentally based design parameters for Portland cement concretes with and without silica fume and fly ash in...

  8. Efficient Synthesis of Functionalized Benzimidazoles and Perimidines: Ytterbium Chloride Catalyzed CmC Bond Cleavage%Efficient Synthesis of Functionalized Benzimidazoles and Perimidines: Ytterbium Chloride Catalyzed CmC Bond Cleavage

    Institute of Scientific and Technical Information of China (English)

    Cai, Lijian; Ji, Xiaofeng; Yao, Zhigang; Xu, Fan; Shen, Qi

    2011-01-01

    An efficient method is developed for the synthesis of functionalized benzimidazoles and perimidines by the condensation of aryl diamines with β-carbonyl compounds catalyzed by ytterbium chloride. The reactions give good yields under mild conditions. A mechanism involving a lanthanide activated C--C bond cleavage is proposed.

  9. Protein carbonylation as a novel mechanism in redox signaling.

    Science.gov (United States)

    Wong, Chi Ming; Cheema, Amrita K; Zhang, Lihua; Suzuki, Yuichiro J

    2008-02-15

    Reactive oxygen species serve as second messengers for signal transduction; however, molecular targets of oxidant signaling have not been defined. Here, we show that ligand-receptor-mediated signaling promotes reactive oxygen species-dependent protein carbonylation. Treatment of pulmonary artery smooth muscle cells with endothelin-1 increased protein carbonyls. Carbonylation of the majority of proteins occurred transiently, suggesting that there is also a mechanism for decarbonylation induced by endothelin-1. Decarbonylation was suppressed by inhibition of thioredoxin reductase, and cellular thioredoxin was upregulated during the decarbonylation phase. These results indicate that endothelin-1 promotes oxidant signaling as well as thioredoxin-mediated reductive signaling to regulate carbonylation and decarbonylation mechanisms. In cells treated with endothelin receptor antagonists, hydrogen peroxide scavengers, or an iron chelator, we identified, via mass spectrometry, proteins that are carbonylated in a receptor- and Fenton reaction-dependent manner, including annexin A1, which promotes apoptosis and suppresses cell growth. Carbonylation of annexin A1 by endothelin-1 was followed by proteasome-dependent degradation of this protein. We propose that carbonylation and subsequent degradation of annexin A1 may play a role in endothelin-mediated cell growth and survival, important events in pulmonary vascular remodeling. Protein carbonylation in response to ligand-receptor interactions represents a novel mechanism in redox signaling.

  10. Carbonyl-Olefin Exchange Reaction: Present State and Outlook

    Science.gov (United States)

    Kalinova, Radostina; Jossifov, Christo

    The carbonyl-olefin exchange reaction (COER) is a new reaction between carbonyl group and olefin double bond, which has a formal similarity with the olefin metathesis (OM) - one carbon atom in the latter is replaced with an oxygen atom. Till now the new reaction is performed successfully only when the two functional groups (carbonyl group and olefin double bond) are in one molecule and are conjugated. The α, β-unsaturated carbonyl compounds (substituted propenones) are the compounds with such a structure. They polymerize giving substituted polyacetylenes. The chain propagation step of this polymerization is in fact the COER. The question arises: is it possible the COER to take place when the two functional groups are not in one molecule and are not conjugated, and could this reaction became an alternative of the existing carbonyl olefination reactions?

  11. Solid-supported sulfonic acid-containing catalysts efficiently promoted one-pot multi-component synthesis of -acetamido carbonyl compounds

    Indian Academy of Sciences (India)

    Mohammad Ali Zolfigol; Ardeshir Khazaei; Abdolkarim Zare; Mohammad Mokhlesi; Tahereh Hekmat-Zadeh; Alireza Hasaninejad; Fatemeh Derakhshan-Panah; Ahmad Reza Moosavi-Zare; Hassan Keypour; Ahmad Ali Dehghani-Firouzabadid; Maria Merajoddin

    2012-03-01

    Silica-functionalized sulfonic acid (SFSA) and sulfuric acid-modified polyethylene glycol-6000 (PEG-OSO3H) efficiently catalysed one-pot multi-component condensation of enolizable ketones or alkyl acetoacetates with arylaldehydes, acetonitrile and acetyl chloride to afford the corresponding -acetamido ketone or ester derivatives in high to excellent yields and in relatively short reaction times. Moreover, in this work, some novel -acetamido carbonyl compounds (i.e., one complex structure) are synthesized.

  12. Metal-free carbonylations by photoredox catalysis.

    Science.gov (United States)

    Majek, Michal; Jacobi von Wangelin, Axel

    2015-02-01

    The synthesis of benzoates from aryl electrophiles and carbon monoxide is a prime example of a transition-metal-catalyzed carbonylation reaction which is widely applied in research and industrial processes. Such reactions proceed in the presence of Pd or Ni catalysts, suitable ligands, and stoichiometric bases. We have developed an alternative procedure that is free of any metal, ligand, and base. The method involves a redox reaction driven by visible light and catalyzed by eosin Y which affords alkyl benzoates from arene diazonium salts, carbon monoxide, and alcohols under mild conditions. Tertiary esters can also be prepared in high yields. DFT calculations and radical trapping experiments support a catalytic photoredox pathway without the requirement for sacrificial redox partners.

  13. Gas-phase chemistry of technetium carbonyl complexes.

    Science.gov (United States)

    Wang, Yang; Qin, Zhi; Fan, Fang-Li; Haba, Hiromitsu; Komori, Yukiko; Cao, Shi-Wei; Wu, Xiao-Lei; Tan, Cun-Min

    2015-05-28

    Gas-phase chemical behaviors of short-lived technetium carbonyl complexes were studied using a low temperature isothermal chromatograph (IC) coupled with a (252)Cf spontaneous fission (SF) source. Fission products recoiled from the (252)Cf SF source were thermalized in a mixed gas containing CO, and then technetium carbonyl complexes were formed from reactions between CO gas and various technetium isotopes. A gas-jet system was employed to transport the volatile carbonyl complexes from a recoil chamber to the IC. Short IC columns made of Fluorinated Ethylene Propylene (FEP) Teflon and quartz were used to obtain chemical information about the technetium carbonyl complexes. The results for the (104)Tc-(106)Tc carbonyl complexes were found to be strongly influenced by the precursors, and showed the chemical behaviors of (104)Mo-(106)Mo carbonyl complexes, respectively. However, (107)Tc and (108)Tc could represent the chemical information of the element technetium due to their high independent yields and the very short half-lives of their precursors (107)Mo and (108)Mo. An adsorption enthalpy of about ΔHads = -43 kJ mol(-1) was determined for the Tc carbonyl complexes on both the Teflon and quartz surfaces by fitting the breakthrough curves of the (107)Tc and (108)Tc carbonyl complexes with a Monte Carlo simulation program. Chemical yields of around 25% were measured for the Tc carbonyl complexes relative to the transport yields obtained with the gas-jet transport of KCl aerosol particles with Ar carrier gas. Furthermore, the influence of a small amount of O2 gas on the yields of the Mo and Tc carbonyl complexes was studied. PMID:25920667

  14. Carbonyl Emissions From Oil and Gas Production Facilities

    Science.gov (United States)

    Lyman, S. N.; O'Neil, T.; Tran, T.

    2015-12-01

    A number of recent studies have targeted emissions of methane and other hydrocarbons from oil and gas exploration and production activity. These measurements are greatly increasing understanding of the atmospheric impacts of oil and gas development. Very few measurements exist, however, of emissions of formaldehyde and other carbonyls from oil and gas equipment. Carbonyls are toxic and serve as important ozone precursors, especially during winter ozone episodes in places like Utah's Uintah Basin. Current air quality models are only able to reproduce observed high wintertime ozone if they incorporate emissions inventories with very high carbonyl emissions. We measured carbonyl emissions from oil and gas equipment and facilities—including glycol dehydrators, liquid storage tanks, raw gas leaks, raw gas-burning engines, and produced water surface impoundments—in Rocky Mountain oil and gas fields. Carbonyl emissions from raw gas were below detection, but emissions of formaldehyde, acetaldehyde, and other carbonyls were detected from liquid storage tanks, glycol dehydrators, and other oil and gas equipment. In some cases, carbonyls may be formed from the degradation of methanol and other chemicals used in oil and gas production, but the collected data provide evidence for other non-combustion formation pathways. Raw gas-burning engines also emitted carbonyls. Emissions from all measured sources were a small fraction of total volatile organic compound emissions. We incorporated our measurements into an emissions inventory, used that inventory in an air quality model (WRF-SMOKE-CAMx), and were unable to reproduce observed high wintertime ozone. This could be because (1) emission sources we have not yet measured, including compressors, gas processing plants, and others, are large; (2) non-carbonyl emissions, especially those that quickly degrade into carbonyls during photochemical processing, are underestimated in the inventory; or (3) the air quality model is unable

  15. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    makes physical sense for the design engineer, i.e. the achieved chloride diffusion coefficients at 1 year and 100 years, D1 and D100 respectively, and the corresponding achieved chloride concentrations at the exposed concrete surface, C1 and C100. Data from field exposure supports the assumption of time...... dependent surface chloride concentrations and the diffusion coefficients. Model parameters for Portland cement concretes with and without silica fume and fly ash in marine atmospheric and submerged South Scandinavian environment are suggested in a companion paper based on 10 years field exposure data....

  16. A New HPLC Method to Determine Carbonyl Compounds in Air

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In this paper, a new HPLC method was established to determine the carbonyl compounds in air. As the absorbent, 2, 4-dinitrophenylhydrazine (2, 4-DNPH) reacted with carbonyls specifically, which form the corresponding 2,4-dinitrophenylhydrazones, then analyzed by HPLC. The chromatographic conditions, the recovery rate, stability of samples, reagent blank, sampling efficiency were all studied systematically. The results showed that this established method had high sensitivity and good selectivity compared with other analytical methods, and it can determine ten carbonyl compounds in air in 26 min simultaneously.

  17. Deposition of carbonyl sulphide to soils

    Science.gov (United States)

    Kluczewski, S. M.; Brown, K. A.; Bel, J. N. B.

    Carbonyl sulphide (COS) is a trace constituent of the atmosphere and is also the main form in which 35S is released from CO 2-cooled nuclear reactors. Measurements of its deposition velocity ( Vg) are therefore important for validating radiological dose models and for interpreting the role of COS in the global S cycle. The Vg of [ 35S]COS to thin layers of several contrasting soils was measured in a through-flow fumigation system. Deposition velocity was not significantly affected by soil type, although deposition to moist soil was significantly greater ( P dried soils, mean values being 5.71 × 10 -6 ms -1 and 3.06 × 10 -6 ms -1, respectively. The results obtained are about three orders of magnitude smaller than published Vg values for SO 2 to similar soils, which suggests that uptake by soils is not a major sink for atmospheric COS. The results are consistent with the hypothesis that deposition to soil of [ 35S]COS from nuclear reactors is unlikely to contribute significantly to radiation dose from the food chain pathway. The reduction in Vg observed in heat-treated soils indicates a microbial involvement in uptake. However, it seems unlikely that microbial metabolism is the rate-controlling step, since stimulation of the microflora by the addition of nutrients did not increase COS deposition.

  18. Theoretical Estimate of Hydride Affinities of Aromatic Carbonyl Compounds

    Institute of Scientific and Technical Information of China (English)

    AI Teng; ZHU Xiao-Qing; CHENG Jin-Pei

    2003-01-01

    @@ Aromatic carbonyl compounds are one type of the most important organic compounds, and the reductions ofthem by hydride agents such as LiAlH4 or NaBH4 are widely used in organic synthesis. The reactivity of carbonyl compounds generally increases in the following order: ketone < aldehyde, and amide < acid < ester < acid halide, which could be related to their hydride affinities (HA). In the previous paper, Robert[1] calculated the absolute HAof a series of small non-aromatic carbonyl compounds. In this paper, we use DFT method at B3LYP/6-311 + + G (2d, 2p)∥B3LYP/6-31 + G* level to estimate hydride affinities of five groups of aromatic carbonyl compounds. The detailed results are listed in Table 1.

  19. 2-Carboxyanilinium chloride monohydrate

    OpenAIRE

    Muhammad Ashraf Chaudhary; Javed Iqbal; M. Nawaz Tahir; Syed Azeem Rashid Ali Zaidi

    2008-01-01

    In the molecule of the title compound, C7H8NO2+·Cl−·H2O, an intramolecular N—H...O hydrogen bond results in the formation of a non-planar six-membered ring adopting a flattened boat conformation. In the crystal structure, intermolecular O—H...O and N—H...Cl hydrogen bonds link the molecules. There is a C=O...π contact between the carbonyl unit and the centroid of the benzene ring. There is a C=O...π contact [C...Cg = 3.5802 (18), C—O...C...

  20. Carbonyl-Olefin Exchange Reaction and Related Chemistry

    Science.gov (United States)

    Jossifov, Christo; Kalinova, Radostina

    A new carbon—carbon double bond forming reaction (carbonyl olefin exchange reaction) mediated by transition metal catalytic systems has been discovered. The catalytic systems used (transition metal halides or oxohalides alone or in combination with Lewis acids) are active only in the case when the two reacting groups are in one molecules and are conjugated. In addition these systems accelerate other reactions which run simultaneously with the carbonyl olefin metathesis rendering a detailed investigation of the process very complicated.

  1. Targeting Reactive Carbonyl Species with Natural Sequestering Agents

    OpenAIRE

    Sung Won Hwang; Yoon-Mi Lee; Giancarlo Aldini; Kyung-Jin Yeum

    2016-01-01

    Reactive carbonyl species generated by the oxidation of polyunsaturated fatty acids and sugars are highly reactive due to their electrophilic nature, and are able to easily react with the nucleophilic sites of proteins as well as DNA causing cellular dysfunction. Levels of reactive carbonyl species and their reaction products have been reported to be elevated in various chronic diseases, including metabolic disorders and neurodegenerative diseases. In an effort to identify sequestering agents...

  2. Carbonyl species characteristics during the evaporation of essential oils

    Science.gov (United States)

    Chiang, Hsiu-Mei; Chiu, Hua-Hsien; Lai, Yen-Ming; Chen, Ching-Yen; Chiang, Hung-Lung

    2010-06-01

    Carbonyls emitted from essential oils can affect the air quality when they are used in indoors, especially under poor ventilation conditions. Lavender, lemon, rose, rosemary, and tea tree oils were selected as typical and popular essential oils to investigate in terms of composition, thermal characteristics and fifteen carbonyl constituents. Based on thermogravimetric (TG) analysis, the activation energy was 7.6-8.3 kcal mol -1, the reaction order was in the range of 0.6-0.7 and the frequency factor was 360-2838 min -1. Formaldehyde, acetaldehyde, acetone, and propionaldehyde were the dominant carbonyl compounds, and their concentrations were 0.034-0.170 ppm. The emission factors of carbonyl compounds were 2.10-3.70 mg g -1, and acetone, propionaldehyde, acetaldehyde, and formaldehyde accounted for a high portion of the emission factor of carbonyl compounds in essential oil exhaust. Some unhealthy carbonyl species such as formaldehyde and valeraldehyde, were measured at low-temperature during the vaporization of essential oils, indicating a potential effect on indoor air quality and human health.

  3. Traditional reactive carbonyl scavengers do not prevent the carbonylation of brain proteins induced by acute glutathione depletion

    OpenAIRE

    Zheng, J; Bizzozero, O. A.

    2010-01-01

    This study investigated the effect of reactive carbonyl species (RCS)-trapping agents on the formation of protein carbonyls during depletion of brain glutathione (GSH). To this end, rat brain slices were incubated with the GSH-depletor diethyl maleate in the absence or presence of chemically different RCS scavengers (hydralazine, methoxylamine, aminoguanidine, pyridoxamine, carnosine, taurine and z-histidine hydrazide). Despite their strong reactivity towards the most common RCS, none of the ...

  4. Chloride removal from vitrification offgas

    International Nuclear Information System (INIS)

    This study identified and investigated techniques of selectively purging chlorides from the low-level waste (LLW) vitrification process with the purge stream acceptable for burial on the Hanford Site. Chlorides will be present in high concentration in several individual feeds to the LLW Vitrification Plant. The chlorides are highly volatile in combustion type melters and are readily absorbed by wet scrubbing of the melter offgas. The Tank Waste Remediation System (TWRS) process flow sheets show that the resulting chloride rich scrub solution is recycled back to the melter. The chlorides must be purged from the recycle loop to prevent the buildup of excessively high chloride concentrations

  5. Clinical features of schizophrenia with enhanced carbonyl stress.

    Science.gov (United States)

    Miyashita, Mitsuhiro; Arai, Makoto; Kobori, Akiko; Ichikawa, Tomoe; Toriumi, Kazuya; Niizato, Kazuhiro; Oshima, Kenichi; Okazaki, Yuji; Yoshikawa, Takeo; Amano, Naoji; Miyata, Toshio; Itokawa, Masanari

    2014-09-01

    Accumulating evidence suggests that advanced glycation end products, generated as a consequence of facilitated carbonyl stress, are implicated in the development of a variety of diseases. These diseases include neurodegenerative illnesses, such as Alzheimer disease. Pyridoxamine is one of the 3 forms of vitamin B6, and it acts by combating carbonyl stress and inhibiting the formation of AGEs. Depletion of pyridoxamine due to enhanced carbonyl stress eventually leads to a decrease in the other forms of vitamin B6, namely pyridoxal and pyridoxine. We previously reported that higher levels of plasma pentosidine, a well-known biomarker for advanced glycation end products, and decreased serum pyridoxal levels were found in a subpopulation of schizophrenic patients. However, there is as yet no clinical characterization of this subset of schizophrenia. In this study, we found that these patients shared many clinical features with treatment-resistant schizophrenia. These include a higher proportion of inpatients, low educational status, longer durations of hospitalization, and higher doses of antipsychotic medication, compared with patients without carbonyl stress. Interestingly, psychopathological symptoms showed a tendency towards negative association with serum vitamin B6 levels. Our results support the idea that treatment regimes reducing carbonyl stress, such as supplementation of pyridoxamine, could provide novel therapeutic benefits for this subgroup of patients. PMID:24062594

  6. [Degradation of succinylcholine chloride].

    Science.gov (United States)

    Németh, G; Török, I; Paál, T

    1993-05-01

    Quantitative thin-layer chormatographic method has been developed for the investigation of the degradation of injection formulations containing succinylcholinium chloride. The method is based on the denistometric determination of the main degradation product, choline at 430 nm after visualization with iodine vapour. The stability of the injection was investigated under various storage conditions and it has been stated that considerable decomposition takes place during as short a period as one week. PMID:8362654

  7. Comparison of antimicrobial properties of monoterpenes and their carbonylated products.

    Science.gov (United States)

    Naigre, R; Kalck, P; Roques, C; Roux, I; Michel, G

    1996-06-01

    Some monoterpenes and their carbonylated products were evaluated for their antibacterial and antifungal properties. The carbonylation of tested monoterpenes was shown to increase the bacteriostatic and fungistatic activities specifically by the contact method. Concerning the killing effects, only (1R,2S,5R)-isopulegol, its carbonylated products, and (R)-carvone showed significant bactericidal activities, particularly against Enterococcus faecium and Escherichia coli above a concentration of 10 microliters/ml. A fungicidal efficiency of (1R,2S,5R)-isopulegol and (R)-carvone against Aspergillus niger was also noted. It seems that the presence of an oxygenated function in the framework increases the antimicrobial properties. However, monoterpenes were more active using a micro-atmosphere method. PMID:8693045

  8. Traditional reactive carbonyl scavengers do not prevent the carbonylation of brain proteins induced by acute glutathione depletion.

    Science.gov (United States)

    Zheng, J; Bizzozero, O A

    2010-03-01

    This study investigated the effect of reactive carbonyl species (RCS)-trapping agents on the formation of protein carbonyls during depletion of brain glutathione (GSH). To this end, rat brain slices were incubated with the GSH-depletor diethyl maleate in the absence or presence of chemically different RCS scavengers (hydralazine, methoxylamine, aminoguanidine, pyridoxamine, carnosine, taurine and z-histidine hydrazide). Despite their strong reactivity towards the most common RCS, none of the scavengers tested, with the exception of hydralazine, prevented protein carbonylation. These findings suggest that the majority of protein-associated carbonyl groups in this oxidative stress paradigm do not derive from stable lipid peroxidation products like malondialdehyde (MDA), acrolein and 4-hydroxynonenal (4-HNE). This conclusion was confirmed by the observation that the amount of MDA-, acrolein- and 4-HNE-protein adducts does not increase upon GSH depletion. Additional studies revealed that the efficacy of hydralazine at preventing carbonylation was due to its ability to reduce oxidative stress, most likely by inhibiting mitochondrial production of superoxide and/or by scavenging lipid free radicals. PMID:20001647

  9. [11C]Carbon Monoxide in Palladium- / Selenium-Promoted Carbonylation Reactions : Synthesis of 11C-Imides, Hydrazides, Amides, Carboxylic Acids, Carboxylic Esters, Carbothioates, Ketones and Carbamoyl Compounds

    OpenAIRE

    Karimi, Farhad

    2002-01-01

    [11C]Carbon monoxide in low concentrations has been used in palladium- or seleniummediated carbonylation reactions such as the synthesis of 11C-imides, hydrazides, amides, carboxylic acids, esters, carbothioates, ketones and carbamoyl compounds. In these reactions aryl iodides have been used in most cases. However, less reactive aryl triflate, chloride and bromides were activated using tetrabutylammonium iodide. The reactivities of nucleophiles may have influence on the radiochemical yield of...

  10. Formation of vesicles with an organometallic amphiphilic bilayer by supramolecular arrangement of metal carbonyl metallosurfactants

    OpenAIRE

    Parera Piella, Elisabet; Comelles, Francesc; Barnadas Rodríguez, Ramon; Suades Ortuño, Joan

    2011-01-01

    Metallo-vesicles are formed in water medium as a result of the supramolecular arrangement of molybdenum carbonyl metallosurfactants. These new kind of surfactants contain a hydrophobic metal carbonyl fragment and are easily prepared from surfactant phosphine ligands

  11. Efficient Nd Promoted Rh Catalysts for Vapor Phase Methanol Carbonylation

    Institute of Scientific and Technical Information of China (English)

    Shu Feng ZHANG; Qing Li QIAN; Ping Lai PAN; Yi CHEN; Guo Qing YUAN

    2005-01-01

    A Nd promoted-Rh catalysts supported on polymer-derived carbon beads for vapor-phase methanol carbonylation was developed. Rh-Nd bimetallic catalysts obviously have higher activity than that of supported Rh catalyst under similar reaction condition. The difference between the activity of above two catalyst systems is clearly caused by the intrinsic properties generated by the introduction of Nd.

  12. Contamination of coal benzol by carbonyl compound impurities

    Energy Technology Data Exchange (ETDEWEB)

    Yakovleva, T.P.

    1985-03-01

    The origin of most carbonyl compounds in nitration-grade benzene produced from coke-oven crude benzole (causing problems in isopropylbenzene production) was concluded to be the piperylene fraction (a by-product of isoprene manufacture) used as an additive in the washing of the benzene with sulphuric acid.

  13. Comparing Carbonyl Chemistry in Comprehensive Introductory Organic Chemistry Textbooks

    Science.gov (United States)

    Nelson, Donna J.; Kumar, Ravi; Ramasamy, Saravanan

    2015-01-01

    Learning the chemistry of compounds containing carbonyl groups is difficult for undergraduate students partly because of a convolution of multiple possible reaction sites, competitive reactions taking place at those sites, different criteria needed to discern between the mechanisms of these reactions, and no straightforward selection method…

  14. α-Carbonyl Radical Cyclizatio n in Organic Synthesis

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@ Intramolecular radical cyclization reactions are now used routinely to synthesize carbocyclic and heterocyclic structures. We have reported that α-carbonyl radicals 1, generated from the corresponding iodo ketones or enones, underwent intramolecular radical cyclization smoothly to afford products 2.1, 2,3

  15. Cobalt carbonyl catalyzed olefin hydroformylation in supercritical carbon dioxide

    Science.gov (United States)

    Rathke, Jerome W.; Klingler, Robert J.

    1993-01-01

    A method of olefin hydroformylation is provided wherein an olefin reacts with a carbonyl catalyst and with reaction gases such as hydrogen and carbon monoxide in the presence of a supercritical reaction solvent, such as carbon dioxide. The invention provides higher yields of n-isomer product without the gas-liquid mixing rate limitation seen in conventional Oxo processes using liquid media.

  16. Iron-Sulfur-Carbonyl and -Nitrosyl Complexes: A Laboratory Experiment.

    Science.gov (United States)

    Glidewell, Christopher; And Others

    1985-01-01

    Background information, materials needed, procedures used, and typical results obtained, are provided for an experiment on iron-sulfur-carbonyl and -nitrosyl complexes. The experiment involved (1) use of inert atmospheric techniques and thin-layer and flexible-column chromatography and (2) interpretation of infrared, hydrogen and carbon-13 nuclear…

  17. Carbonyl Sulfides as Possible Intermediates in the Photolysis of Oxathiiranes

    DEFF Research Database (Denmark)

    Carlsen, Lars; Snyder, J. P.; Holm, A.;

    1981-01-01

    species and several dipolarophiles is rationlized in terms of a labile carbonyl suffide intermediate capable of facile sulfur extrusion from a long, weak O-S bond. Finally, the electronic absorption spectra of a series of para-substituted benzaldehyde O-sulfide model system have been calculated with CNDO...

  18. Age-related variations of protein carbonyls in human saliva and plasma: is saliva protein carbonyls an alternative biomarker of aging?

    Science.gov (United States)

    Wang, Zhihui; Wang, Yanyi; Liu, Hongchen; Che, Yuwei; Xu, Yingying; E, Lingling

    2015-06-01

    Free radical hypothesis which is one of the most acknowledged aging theories was developed into oxidative stress hypothesis. Protein carbonylation is by far one of the most widely used markers of protein oxidation. We studied the role of age and gender in protein carbonyl content of saliva and plasma among 273 Chinese healthy subjects (137 females and 136 males aged between 20 and 79) and discussed the correlation between protein carbonyl content of saliva and plasma. Protein carbonyl content of saliva and plasma were, respectively, 2.391 ± 0.639 and 0.838 ± 0.274 nmol/mg. Variations of saliva and plasma different age groups all reached significant differences in both male and female (all p saliva and plasma protein carbonyls were found to be significantly correlated with age (r = 0.6582 and r = 0.5176, all p saliva and plasma protein carbonyl levels (all p > 0.05). Saliva and plasma protein carbonyls were positively related (r = 0.4405, p saliva and plasma protein carbonyls/ferric reducing ability of plasma (FRAP) ratios were proved to be significantly correlated with age (r = 0.7796 and r = 0.6938, all p saliva protein carbonyls/FRAP ratio and plasma protein carbonyls/FRAP ratio were also correlated (r = 0.5573, p saliva protein carbonyls seem to be an alternative biomarker of aging while the mechanisms of protein carbonylation and oxidative stress and the relationship between saliva protein carbonyls and diseases need to be further investigated.

  19. High throughput assay for evaluation of reactive carbonyl scavenging capacity ☆

    OpenAIRE

    N. Vidal; J.P. Cavaille; Graziani, F.; M. Robin; Ouari, O; Pietri, S.; Stocker, P.

    2014-01-01

    Many carbonyl species from either lipid peroxidation or glycoxidation are extremely reactive and can disrupt the function of proteins and enzymes. 4-hydroxynonenal and methylglyoxal are the most abundant and toxic lipid-derived reactive carbonyl species. The presence of these toxics leads to carbonyl stress and cause a significant amount of macromolecular damages in several diseases. Much evidence indicates trapping of reactive carbonyl intermediates may be a useful strategy for inhibiting or...

  20. Plasma protein carbonyl levels and breast cancer risk.

    Science.gov (United States)

    Rossner, Pavel; Terry, Mary Beth; Gammon, Marilie D; Agrawal, Meenakshi; Zhang, Fang Fang; Ferris, Jennifer S; Teitelbaum, Susan L; Eng, Sybil M; Gaudet, Mia M; Neugut, Alfred I; Santella, Regina M

    2007-01-01

    To study the role of oxidative stress in breast cancer risk, we analysed plasma levels of protein carbonyls in 1050 cases and 1107 controls. We found a statistically significant trend in breast cancer risk in relation to increasing quartiles of plasma protein carbonyl levels (OR = 1.2, 95% CI = 0.9-1.5; OR = 1.5, 95% CI = 1.2-2.0; OR = 1.6, 95% CI = 1.2-2.1, for the 2(nd), 3(rd) and 4(th) quartile relative to the lowest quartile, respectively, P for trend = 0.0001). The increase in risk was similar for younger ( or = 15 grams/day for 4(th) quartile versus lowest quartile OR = 2.3, 95% CI = 1.1-4.7), and hormone replacement therapy use (HRT, OR = 2.6, 95% CI = 1.6-4.4 for 4(th) quartile versus lowest quartile). The multiplicative interaction terms were statistically significant only for physical activity and HRT. The positive association between plasma protein carbonyl levels and breast cancer risk was also observed when the analysis was restricted to women who had not received chemotherapy or radiation therapy prior to blood collection. Among controls, oxidized protein levels significantly increased with cigarette smoking and higher fruit and vegetable consumption, and decreased with alcohol consumption >30 grams per day. Women with higher levels of plasma protein carbonyl and urinary 15F(2t)-isoprostane had an 80% increase in breast cancer risk (OR = 1.8, 95% CI = 1.2-2.6) compared to women with levels below the median for both markers of oxidative stress. In summary, our results suggest that increased plasma protein carbonyl levels may be associated with breast cancer risk.

  1. Valyl benzyl ester chloride

    Directory of Open Access Journals (Sweden)

    Grzegorz Dutkiewicz

    2010-02-01

    Full Text Available In the title compound (systematic name: 1-benzyloxy-3-methyl-1-oxobutan-2-aminium chloride, C12H18NO2+·Cl−, the ester group is approximately planar, with a maximum deviation of 0.040 (2 Å from the least-squares plane, and makes a dihedral angle of 28.92 (16° with the phenyl ring. The crystal structure is organized by N—H...Cl hydrogen bonds which join the two components into a chain along the b axis. Pairs of chains arranged antiparallel are interconnected by further N—H...Cl hydrogen bonds, forming eight-membered rings. Similar packing modes have been observed in a number of amino acid ester halides with a short unit-cell parameter of ca 5.5 Å along the direction in which the chains run.

  2. Protein carbonylation and metal-catalyzed protein oxidation in a cellular perspective

    DEFF Research Database (Denmark)

    Møller, Ian Max; Rogowska-Wrzesinska, Adelina; Rao, R S P

    2011-01-01

    to be relevant in physiological processes, irreversible oxidative modifications are known to contribute to cellular damage and disease. The most well-studied irreversible protein oxidation is carbonylation. In this work we first examine how protein carbonylation occurs via metal-catalyzed oxidation (MCO) in vivo...... and in vitro with an emphasis on cellular metal ion homeostasis and metal binding. We then review proteomic methods currently used for identifying carbonylated proteins and their sites of modification. Finally, we discuss the identified carbonylated proteins and the pattern of carbonylation sites in relation...

  3. Phenolic carbonyls undergo rapid aqueous photodegradation to form low-volatility, light-absorbing products

    Science.gov (United States)

    Smith, Jeremy D.; Kinney, Haley; Anastasio, Cort

    2016-02-01

    We investigated the aqueous photochemistry of six phenolic carbonyls - vanillin, acetovanillone, guaiacyl acetone, syringaldehyde, acetosyringone, and coniferyl aldehyde - that are emitted from wood combustion. The phenolic carbonyls absorb significant amounts of solar radiation and decay rapidly via direct photodegradation, with lifetimes (τ) of 13-140 min under Davis, CA winter solstice sunlight at midday (solar zenith angle = 62°). The one exception is guaiacyl acetone, where the carbonyl group is not directly connected to the aromatic ring: This species absorbs very little sunlight and undergoes direct photodegradation very slowly (τ > 103 min). We also found that the triplet excited states (3C*) of the phenolic carbonyls rapidly oxidize syringol (a methoxyphenol without a carbonyl group), on timescales of 1-5 h for solutions containing 5 μM phenolic carbonyl. The direct photodegradation of the phenolic carbonyls, and the oxidation of syringol by 3C*, both efficiently produce low volatility products, with SOA mass yields ranging from 80 to 140%. Contrary to most aliphatic carbonyls, under typical fog conditions we find that the primary sink for the aromatic phenolic carbonyls is direct photodegradation in the aqueous phase. In areas of significant wood combustion, phenolic carbonyls appear to be small but significant sources of aqueous SOA: over the course of a few hours, nearly all of the phenolic carbonyls will be converted to SOA via direct photodegradation, enhancing the POA mass from wood combustion by approximately 3-5%.

  4. [Carbonyl stress and oxidatively modified proteins in chronic renal failure].

    Science.gov (United States)

    Bargnoux, A-S; Morena, M; Badiou, S; Dupuy, A-M; Canaud, B; Cristol, J-P

    2009-01-01

    Oxidative stress is commonly observed in chronic renal failure patients resulting from an unbalance between overproduction of reactive oxygen species and impairement of defense mechanisms. Proteins appear as potential targets of uremia-induced oxidative stress and may undergo qualitative modifications. Proteins could be directly modified by reactive oxygen species which leads to amino acid oxydation and cross-linking. Proteins could be indirectly modified by reactive carbonyl compounds produced by glycoxidation and lipo-peroxidation. The resulting post-traductional modifications are known as carbonyl stress. In addition, thiols could be oxidized or could react with homocystein leading to homocysteinylation. Finally, tyrosin could be oxidized by myeloperoxidase leading to advanced oxidative protein products (AOPP). Oxidatively modified proteins are increased in chronic renal failure patients and may contribute to exacerbate the oxidative stress/inflammation syndrome. They have been involved in long term complications of uremia such as amyloidosis and accelerated atherosclerosis. PMID:19297289

  5. Role of Carbonyl Modifications on Aging-Associated Protein Aggregation

    Science.gov (United States)

    Tanase, Maya; Urbanska, Aleksandra M.; Zolla, Valerio; Clement, Cristina C.; Huang, Liling; Morozova, Kateryna; Follo, Carlo; Goldberg, Michael; Roda, Barbara; Reschiglian, Pierluigi; Santambrogio, Laura

    2016-01-01

    Protein aggregation is a common biological phenomenon, observed in different physiological and pathological conditions. Decreased protein solubility and a tendency to aggregate is also observed during physiological aging but the causes are currently unknown. Herein we performed a biophysical separation of aging-related high molecular weight aggregates, isolated from the bone marrow and splenic cells of aging mice and followed by biochemical and mass spectrometric analysis. The analysis indicated that compared to younger mice an increase in protein post-translational carbonylation was observed. The causative role of these modifications in inducing protein misfolding and aggregation was determined by inducing carbonyl stress in young mice, which recapitulated the increased protein aggregation observed in old mice. Altogether our analysis indicates that oxidative stress-related post-translational modifications accumulate in the aging proteome and are responsible for increased protein aggregation and altered cell proteostasis.

  6. Anchoring selenido-carbonyl ruthenium clusters to functionalized silica xerogels

    Energy Technology Data Exchange (ETDEWEB)

    Cauzzi, Daniele; Graiff, Claudia; Pattacini, Roberto; Predieri, Giovanni; Tiripicchio, Antonio [Universita di Parma (Italy). Dipt. di Chimica Generale ed Inorganica, Chimica Analitica, Chimica Fisica]. E-mail: tiri@unipr.it

    2003-12-01

    Silica Xerogels containing carbonyl Ru{sub 3}Se{sub 2} nido clusters were prepared in three different ways. The simple dispersion of [Ru{sub 3}({mu}{sub 3}-Se){sub 2}(CO){sub 7}(PPh {sub 3}){sub 2}] via sol gel process produces an inhomogeneous material; by contrast, homogeneous xerogels were obtained by reaction of [Ru{sub 3}({mu}{sub 3}-Se){sub 2}(CO){sub 8}(PPh {sub 3})] with functionalized xerogels containing grafted diphenylphosphine moieties and by reaction of [Ru{sub 3}(CO){sub 12}] with a xerogel containing grafted phosphine-selenide groups. The reaction between [Ru{sub 3}(CO){sub 12}] and dodecyl diphenylphosphine selenide led to the formation of four selenido carbonyl clusters, which are soluble in hydrocarbon solvents and can be deposited as thin films from their solution by slow evaporation. (author)

  7. 40 CFR 61.65 - Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... dichloride, vinyl chloride and polyvinyl chloride plants. 61.65 Section 61.65 Protection of Environment... dichloride, vinyl chloride and polyvinyl chloride plants. An owner or operator of an ethylene dichloride, vinyl chloride, and/or polyvinyl chloride plant shall comply with the requirements of this section....

  8. Special Topic 3B: Acidity, Basicity, and Carbonyl Condensation Reactions

    OpenAIRE

    Christiansen, Mike A

    2012-01-01

    The purpose of this video is to help second-year organic chemistry students review the concepts and questions that most frequently appear on standardized entrance exams, like the MCAT, DAT, PCAT, and GRE. I'll here teach you how to sort molecules according to acidity and basicity. I'll also review the following carbonyl condensation and related reactions: the aldol reaction, the Claisen and intramolecular diketone condensations, and the malonic ester synthesis. --Dr. Mike Christiansen from Ut...

  9. Iron(III)-catalysed carbonyl-olefin metathesis.

    Science.gov (United States)

    Ludwig, Jacob R; Zimmerman, Paul M; Gianino, Joseph B; Schindler, Corinna S

    2016-05-19

    The olefin metathesis reaction of two unsaturated substrates is one of the most powerful carbon-carbon-bond-forming reactions in organic chemistry. Specifically, the catalytic olefin metathesis reaction has led to profound developments in the synthesis of molecules relevant to the petroleum, materials, agricultural and pharmaceutical industries. These reactions are characterized by their use of discrete metal alkylidene catalysts that operate via a well-established mechanism. While the corresponding carbonyl-olefin metathesis reaction can also be used to construct carbon-carbon bonds, currently available methods are scarce and severely hampered by either harsh reaction conditions or the required use of stoichiometric transition metals as reagents. To date, no general protocol for catalytic carbonyl-olefin metathesis has been reported. Here we demonstrate a catalytic carbonyl-olefin ring-closing metathesis reaction that uses iron, an Earth-abundant and environmentally benign transition metal, as a catalyst. This transformation accommodates a variety of substrates and is distinguished by its operational simplicity, mild reaction conditions, high functional-group tolerance, and amenability to gram-scale synthesis. We anticipate that these characteristics, coupled with the efficiency of this reaction, will allow for further advances in areas that have historically been enhanced by olefin metathesis. PMID:27120158

  10. Iron(III)-catalysed carbonyl-olefin metathesis.

    Science.gov (United States)

    Ludwig, Jacob R; Zimmerman, Paul M; Gianino, Joseph B; Schindler, Corinna S

    2016-04-27

    The olefin metathesis reaction of two unsaturated substrates is one of the most powerful carbon-carbon-bond-forming reactions in organic chemistry. Specifically, the catalytic olefin metathesis reaction has led to profound developments in the synthesis of molecules relevant to the petroleum, materials, agricultural and pharmaceutical industries. These reactions are characterized by their use of discrete metal alkylidene catalysts that operate via a well-established mechanism. While the corresponding carbonyl-olefin metathesis reaction can also be used to construct carbon-carbon bonds, currently available methods are scarce and severely hampered by either harsh reaction conditions or the required use of stoichiometric transition metals as reagents. To date, no general protocol for catalytic carbonyl-olefin metathesis has been reported. Here we demonstrate a catalytic carbonyl-olefin ring-closing metathesis reaction that uses iron, an Earth-abundant and environmentally benign transition metal, as a catalyst. This transformation accommodates a variety of substrates and is distinguished by its operational simplicity, mild reaction conditions, high functional-group tolerance, and amenability to gram-scale synthesis. We anticipate that these characteristics, coupled with the efficiency of this reaction, will allow for further advances in areas that have historically been enhanced by olefin metathesis.

  11. Carbonylation of Ethene Catalysed by Pd(II-Phosphine Complexes

    Directory of Open Access Journals (Sweden)

    Gianni Cavinato

    2014-09-01

    Full Text Available This review deals with olefin carbonylation catalysed by Pd(II-phosphine complexes in protic solvents. In particular, the results obtained in the carbonylation with ethene are reviewed. After a short description of the basic concepts relevant to this catalysis, the review treats in greater details the influence of the bite angle, skeletal rigidity, electronic and steric bulk properties of the ligand on the formation of the products, which range from high molecular weight perfectly alternating polyketones to methyl propanoate. It is shown that the steric bulk plays a major role in directing the selectivity. Particular emphasis is given to the factors governing the very active and selective catalysis to methyl propanoate, including the mechanism of the catalytic cycles with diphosphine- and monophosphine-catalysts. A brief note on the synthesis of methyl propanoate using a “Lucite” type catalyst in ionic liquids is also illustrated. A chapter is dedicated to the carbonylation of olefins in aqueous reaction media. The nonalternating CO-ethene copolymerization is also treated.

  12. Iron(III)-catalysed carbonyl-olefin metathesis

    Science.gov (United States)

    Ludwig, Jacob R.; Zimmerman, Paul M.; Gianino, Joseph B.; Schindler, Corinna S.

    2016-05-01

    The olefin metathesis reaction of two unsaturated substrates is one of the most powerful carbon-carbon-bond-forming reactions in organic chemistry. Specifically, the catalytic olefin metathesis reaction has led to profound developments in the synthesis of molecules relevant to the petroleum, materials, agricultural and pharmaceutical industries. These reactions are characterized by their use of discrete metal alkylidene catalysts that operate via a well-established mechanism. While the corresponding carbonyl-olefin metathesis reaction can also be used to construct carbon-carbon bonds, currently available methods are scarce and severely hampered by either harsh reaction conditions or the required use of stoichiometric transition metals as reagents. To date, no general protocol for catalytic carbonyl-olefin metathesis has been reported. Here we demonstrate a catalytic carbonyl-olefin ring-closing metathesis reaction that uses iron, an Earth-abundant and environmentally benign transition metal, as a catalyst. This transformation accommodates a variety of substrates and is distinguished by its operational simplicity, mild reaction conditions, high functional-group tolerance, and amenability to gram-scale synthesis. We anticipate that these characteristics, coupled with the efficiency of this reaction, will allow for further advances in areas that have historically been enhanced by olefin metathesis.

  13. Beads,Necklaces, Chains and Strings in Capping Carbonyl Clusters

    Directory of Open Access Journals (Sweden)

    Enos Masheija Kiremire

    2015-09-01

    Full Text Available The paper attempts to explain at length the close relationship between transition metal carbonyl clusters with main group clusters especially the boranes using the 14n and 4n rules. When the ‘shielding’ electrons are removed from a transition metal carbonyl cluster and becomes ‘naked’, it resembles a corresponding one in the main group elements. A an expanded table of osmium carbonyl clusters was constructed using the capping fragment Os(CO2(14n-2 and the fragment Os(CO3 (14n+0. The table reveals the fact that the known series such closo, nido and arachno are part and parcel of a wide range of series especially the capping series 14n+q, where q takes up negative multiple integers of two including 0 such as such = 0, -2,-4, -6, and so on. The linkage between capping series in transition metal carbonyl clusters has also been identified. Apart from the capping series generated in the table, there is another type of series where the skeletal cluster elements remained the same but the number of carbonyl ligands successively decreased. These types of series are referred to as stripping series. Mapping generating functions were also derived which produces any cluster formula or series required. Also the table shows that many clusters form utilizing some of its atoms as closo nucleus around which the larger ones are built and thus forming clusters within larger clusters. The table may be used to categorize a given cluster formula that falls within its range. Otherwise, using the 14n rule or 4n rule can be used for cluster classification. Furthermore, the table indicated that atoms, fragments and molecules can be classified into series. Through this approach of using series, Hoffmann’s important isolobal relationship of chemical species can splendidly be explained.Using the 14n rule and 4n rules creates a framework under which chemical species such as atoms, fragments, molecules and ions some of which may appear unrelated from main group

  14. Sodium chloride, potassium chloride, and virulence in Listeria monocytogenes.

    OpenAIRE

    MYERS, E. R.; Dallmier, A W; Martin, S E

    1993-01-01

    Virulence, as determined in a mouse model, and the virulence factor activities of catalase, superoxide dismutase, and listeriolysin O were examined in a parental strain (10403S) and in a nonhemolytic mutant strain (DP-L224) of Listeria monocytogenes. The cells were propagated in media containing various concentrations of sodium chloride or potassium chloride. Strains 10403S and DP-L224 exhibited significant increases in catalase activity and listeriolysin O activity when grown in medium conta...

  15. [Chemical Characteristics and Sources of Atmospheric Carbonyls During the 2014 Beijing APEC].

    Science.gov (United States)

    He, Xiao-lang; Tan, Ji-hua; Guo, Song-jun; Ma, Yong-liang; He, Ke-bin

    2016-03-15

    Pollution characteristic and variation trend of atmospheric carbonyls were investigated in November during the 2014 Beijing APEC. Formaldehyde, acetaldehyde and acetone were the dominant carbonyls, accounting for 82.66% of total carbonyls, and especially, formaldehyde accounted for 40.12% of total carbonyls. Atmospheric concentrations of total carbonyls decreased by around 64.10% after the clean air policy was carried out during the Beijing APEC, and the variation trend of carbonyls showed a similar pattern to those of other pollutants like PM₂.₅ during the APEC. Strong correlations (R² of 0.67-0.98) were observed among formaldehyde, acetaldehyde, acetone and total carbonyls during and after the APEC, indicating that they had similar sources; however, poor correlations (R² of -0.11-0.42 and 0.16-0.94, respectively) were observed before the APEC, implying different emission sources for ambient carbonyls. The calculated ratios of C1/C2, C2/C3 and OC/EC indicated that both vehicles and coal emissions were responsible for atmospheric carbonyls before the APEC, and emissions from coal burning were the major contributor to atmospheric carbonyls during and after the APEC, especially after the APEC. PMID:27337869

  16. Indoor carbonyl compounds in an academic building in Beijing, China: concentrations and influencing factors

    Institute of Scientific and Technical Information of China (English)

    Chuanjia JIANG; Pengyi ZHANG

    2012-01-01

    Carbonyl compounds in indoor air are of great concern for their adverse health effects. Between February and May, 2009, concentrations of 13 carbonyl compounds were measured in an academic building in Beijing, China. Total concentration of the detected carbonyls ranged from 20.7 to 189.1 I.tg.m3, and among them acetone and formaldehyde were the most abundant, with mean concentrations of 26.4 and 22.6gg.m-3, respectively. Average indoor concentrations of other carbonyls were below I 0 gg. m~3. Principal component analysis identified a combined effect of common indoor carbonyl sources and ventilation on indoor carbonyl levels. Diurnal variations of the carbonyl compounds were investigated in one office room, and carbonyl concentrations tended to be lower in the daytime than at night, due to enhanced ventilation. Average concentrations of carbonyl compounds in the office room were generally higher in early May than in late February, indicating the influence of temperature. Carbo- nyl source emission rates from both the room and human occupants were estimated during two lectures, based on one-compartment mass balance model. The influence of human occupants on indoor carbonyl concentrations varies with environmental conditions, and may become signifi- cant in the case of a large human occupancy.

  17. Chloride channels in stroke

    Institute of Scientific and Technical Information of China (English)

    Ya-ping ZHANG; Hao ZHANG; Dayue Darrel DUAN

    2013-01-01

    Vascular remodeling of cerebral arterioles,including proliferation,migration,and apoptosis of vascular smooth muscle cells (VSMCs),is the major cause of changes in the cross-sectional area and diameter of the arteries and sudden interruption of blood flow or hemorrhage in the brain,ie,stroke.Accumulating evidence strongly supports an important role for chloride (Clˉ) channels in vascular remodeling and stroke.At least three Clˉ channel genes are expressed in VSMCs:1) the TMEM16A (or Ano1),which may encode the calcium-activated Clˉ channels (CACCs); 2) the CLC-3 Clˉ channel and Clˉ/H+ antiporter,which is closely related to the volume-regulated Clˉ channels (VRCCs); and 3) the cystic fibrosis transmembrane conductance regulator (CFTR),which encodes the PKA-and PKC-activated Clˉ channels.Activation of the CACCs by agonist-induced increase in intracellular Ca2+ causes membrane depolarization,vasoconstriction,and inhibition of VSMC proliferation.Activation of VRCCs by cell volume increase or membrane stretch promotes the production of reactive oxygen species,induces proliferation and inhibits apoptosis of VSMCs.Activation of CFTR inhibits oxidative stress and may prevent the development of hypertension.In addition,Clˉ current mediated by gammaaminobutyric acid (GABA) receptor has also been implicated a role in ischemic neuron death.This review focuses on the functional roles of Clˉ channels in the development of stroke and provides a perspective on the future directions for research and the potential to develop Clˉ channels as new targets for the prevention and treatment of stroke.

  18. Frustrated Lewis pairs-assisted reduction of carbonyl compounds

    DEFF Research Database (Denmark)

    Marek, Ales; Pedersen, Martin Holst Friborg

    2015-01-01

    An alternative and robust method for the reduction of carbonyl groups by frustrated Lewis pairs (FLPs) is reported in this paper. With its very mild reaction conditions, good to excellent yields, absolute regioselectivity and the non-metallic character of the reagent, it provides an excellent too...... for H-1, H-2 as well as H-3 chemistry. It is a new strategy for the one-pot synthesis of aromatic alcohols selectively labeled with heavy isotopes of hydrogen. © 2015 Elsevier Ltd. All rights reserved....

  19. Analysis of dynamic protein carbonylation in rice embryo during germination through AP-SWATH.

    Science.gov (United States)

    Zhang, Hui; He, Dongli; Yu, Jianlan; Li, Ming; Damaris, Rebecca Njeri; Gupta, Ravi; Kim, Sun Tae; Yang, Pingfang

    2016-03-01

    Seed germination is an important aspect of the plant life cycle, during which, reactive oxygen species (ROS) accumulate. The accumulation of ROS results in an increase in protein oxidation of which carbonylation is the most canonical one. However, there is insufficient information concerning protein oxidation, especially carbonylation and its contribution to seed germination. In this study, biotin hydrazide labeled chromatography combined with sequential window acquisition of all theoretical fragment ion spectra (SWATH) method was used to analyze the dynamic pattern of protein carbonylation in rice embryos during germination. A total of 1872 unique proteins were quantified, among which 288 carbonylated peptides corresponding to 144 proteins were determined based on the filtering through mass shifts of modified amino acids. In addition, 66 carbonylated proteins were further analyzed based on their carbonylation intensity in four stages of germination. These identified carbonylated proteins were mainly involved in maintaining the levels of ROS, abscisic acid and seed reserves. Remarkably, a peroxiredoxin was found with 23 unique carbonylated peptides, and the expression of which was consistent with its increased activity. This study describes the dynamic pattern of carbonylated proteins during seed germination, and may help to further understand the biochemical mechanisms on this process. PMID:26801057

  20. Nano-Aluminum Powder Mediated Allylation of Carbonyl Compounds in Aqueous Media

    Institute of Scientific and Technical Information of China (English)

    YUAN Shi-Zhen; LIU Jin

    2008-01-01

    A new and effective Barbier-Grignard allylation of aldehydes or ketones has been carried out with nano-aluminum powder in aqueous 0.1 mol·L-1 NH4Cl (aq.) under an atmosphere of nitrogen. Aromatic carbonyl compounds gave homoallylic alcohols in good yields. The effectiveness of reaction was strongly influenced by the steric environment surrounding the carbonyl group. Aliphatic carbonyl compounds proceeded in low yields. The dominant stereoisomer was an erythro-isomer when an ortho-hydroxyl carbonyl compound was reacted under such a reaction condition.

  1. The carbonyl oxide-aldehyde complex: a new intermediate of the ozonolysis reaction

    Science.gov (United States)

    Cremer, Dieter; Kraka, Elfi; McKee, M. L.; Radharkrishnan, T. P.

    1991-12-01

    MP4(SDQ)/6-31G (d,p) calculations suggest that the ozonolysis of alkenes in solution phase does not proceed via carbonyl oxide, but via a dipole complex between aldehyde and carbonyl oxide, which is 9 kcal/mol more stable than the separated molecules. The dipole complex is probably formed in the solvent cage upon decomposition of primary ozonide to aldehyde and carbonyl oxide. Rotation of either aldehyde or carbonyl oxide in the solvent cage leads to an antiparallel alignment of molecular dipole moments and dipole-dipole attraction.

  2. trans-Di-μ-carbonyl-bis{carbonyl[η5-2,3,4,5-tetramethyl-1-(5-methyl-2-furylcyclopentadienyl]ruthenium(I}(Ru—Ru

    Directory of Open Access Journals (Sweden)

    Jin Lin

    2009-08-01

    Full Text Available In the crystal structure of the title compound, [Ru2(C14H17O2(CO4], each RuI atom is connected to one end-on and two bridging carbonyl groups and one cyclopentadienyl ring. The two Ru atoms are connected into binuclear complexes via two bridging carbonyl groups, forming four-membered rings which are located on centres of inversion. The Ru—Ru distance of 2.7483 (11 Å corresponds to a single bond. The two carbonyl groups in these binuclear complexes are trans-oriented.

  3. Reactivity of Ir(III) carbonyl complexes with water: alternative by-product formation pathways in catalytic methanol carbonylation

    OpenAIRE

    Haynes, A.; Elliott, P. I. P.; Haak, S; Meijer, A.J.H.M.; Sunley, G.J

    2013-01-01

    The reactions of water with a number of iridium(III) complexes relevant to the mechanism for catalytic methanol carbonylation are reported. The iridium acetyl, [Ir(CO)2I3(COMe)]−, reacts with water under mild conditions to release CO2 and CH4, rather than the expected acetic acid. Isotopic labeling and kinetic experiments are consistent with a mechanism involving nucleophilic attack by water on a terminal CO ligand of [Ir(CO)2I3(COMe)]− to give an (undetected) hydroxycarbonyl spec...

  4. IRC analysis of methanol carbonylation reaction catalyzed by rhodium complex

    Institute of Scientific and Technical Information of China (English)

    HAO; Maorong; FENG; Wenlin; JI; Yongqiang; LEI; Ming

    2004-01-01

    In the reaction cycle for methanol carbonylation catalyzed by Rh complex, the structure geometries of the reactant, intermediates, transition states and product of each elemental reaction have been studied by using the energy gradient method at HF/LANL2DZ level, and the changes of their potential profiles have also been calculated. Through IRC analyses of the transition states for each elemental reaction, it is confirmed that the various structure geometries obtained are stationary points on the cycle reaction pathway of methanol carbonylation catalyzed by Rh complex, and the changes are given in energies and structure geometries of the reactant molecules along the reaction pathway of lowest energy. It has been proposed that the geometrical conversions of intermediates play an important role during the cycle reaction. Through analyses of structure geometries, it has been suggested that, in addition to cis- and trans- structure exchange linkage of catalysis reactive species, the two pathways, cis- and trans-cata- lyzed cycle reactions, can also be linked through geometrical conversion of intermediates, of which the activation energy is 49.79 kJ/mol. Moreover, the reductive elimination elemental reaction may be neither cis-cycle nor trans- one, showing that the cycle reaction can be achieved through various pathways. However different the pathway, the oxidative addition elemental reaction of CH3I is the rate-controlling step.

  5. A step-by-step protocol for assaying protein carbonylation in biological samples.

    Science.gov (United States)

    Colombo, Graziano; Clerici, Marco; Garavaglia, Maria Elisa; Giustarini, Daniela; Rossi, Ranieri; Milzani, Aldo; Dalle-Donne, Isabella

    2016-04-15

    Protein carbonylation represents the most frequent and usually irreversible oxidative modification affecting proteins. This modification is chemically stable and this feature is particularly important for storage and detection of carbonylated proteins. Many biochemical and analytical methods have been developed during the last thirty years to assay protein carbonylation. The most successful method consists on protein carbonyl (PCO) derivatization with 2,4-dinitrophenylhydrazine (DNPH) and consequent spectrophotometric assay. This assay allows a global quantification of PCO content due to the ability of DNPH to react with carbonyl giving rise to an adduct able to absorb at 366 nm. Similar approaches were also developed employing chromatographic separation, in particular HPLC, and parallel detection of absorbing adducts. Subsequently, immunological techniques, such as Western immunoblot or ELISA, have been developed leading to an increase of sensitivity in protein carbonylation detection. Currently, they are widely employed to evaluate change in total protein carbonylation and eventually to highlight the specific proteins undergoing selective oxidation. In the last decade, many mass spectrometry (MS) approaches have been developed for the identification of the carbonylated proteins and the relative amino acid residues modified to carbonyl derivatives. Although these MS methods are much more focused and detailed due to their ability to identify the amino acid residues undergoing carbonylation, they still require too expensive equipments and, therefore, are limited in distribution. In this protocol paper, we summarise and comment on the most diffuse protocols that a standard laboratory can employ to assess protein carbonylation; in particular, we describe step-by-step the different protocols, adding suggestions coming from our on-bench experience.

  6. Influences of characteristic meteorological conditions on atmospheric carbonyls in Beijing, China

    Science.gov (United States)

    Pang, Xiaobing; Mu, Yujing; Lee, Xinqing; Zhang, Yujie; Xu, Zhu

    2009-08-01

    Atmospheric pollutants are controlled not only by their production rates but also by meteorological conditions. The influences of dust storm, sauna weather (haze with high temperature and high humidity), wet precipitation and wind speed on atmospheric carbonyls in Beijing were investigated. During a severe dust episode (April 17, 2006), the mixing ratios of carbonyls were significantly elevated to 13-27 ppbV from 7 to 13 ppbV in the previous non-dust days (April 15 and 16) with the increasing extents of 38-154%. The accumulating effect and the lower photolysis rate in the dust day may be responsible for the increases of carbonyls' levels. Additionally, the contribution from heterogeneous reactions occurring on dust particles to formaldehyde and acetaldehyde cannot be ruled out. During the period of typical sauna weather, the concentrations of atmospheric carbonyls increased to 18-60 ppbV from 10 to 17 ppbV before the sauna days. The air mass over Beijing during the sauna days was controlled by a subtropical anticyclone and the boundary layer became quite stable, which was beneficial to the rapid accumulation of air pollutants including carbonyls. Wet precipitation was found to be an effective removal process to the atmospheric carbonyls. After one-hour of rain in summer, the total concentrations of atmospheric carbonyls decreased to less than half of that before the rainfall. The similar temporal varying patterns of carbonyls and inorganic ions in rainwater indicated that carbonyls were mainly washed out from the atmosphere into rainwater as inorganic ions were. Strong wind could evidently dilute atmospheric carbonyls and a negative correlation was found between wind speeds and the concentrations of carbonyls in spring in Beijing.

  7. Stability of succinylcholine chloride injection.

    Science.gov (United States)

    Schmutz, C W; Mühlebach, S F

    1991-03-01

    The stability of succinylcholine chloride injection prepared by a hospital pharmacy was studied under a wide variety of conditions. Batches of succinylcholine chloride injection 10 mg/mL containing sodium chloride, methyl-4-hydroxybenzoate, hydrochloric acid, and water were prepared. Samples were tested for the effect of initial pH (3.0 and 4.2) and sterilization (steam treatment at 100 degrees C for 30 minutes and 121 degrees C for 20 minutes) on stability after three weeks; long-term stability under refrigeration (12, 17, and 23 months of storage at 4 degrees C); and the effect of storage temperature (4-6 degrees C, 20-26 degrees C, 35 degrees C, and 70 degrees C) and light exposure at various intervals up to 12 months. Samples were analyzed by thin-layer chromatography (TLC) and high-performance liquid chromatography (HPLC). Unlike heating at 121 degrees C, heating at 100 degrees C produced no significant loss of succinylcholine chloride, independent of the initial pH. Succinylcholine chloride was hydrolyzed only minimally over 23 months if the solution was stored at 4-6 degrees C. A 10% loss of drug content occurred if solutions were kept at 20-26 degrees C for five months, at 35 degrees C for one month, or at 70 degrees C for one day. Initial degradation was slowed if the solution was protected from light. The assessments by TLC proved to be more sensitive than the HPLC measurements. Succinylcholine chloride injection sterilized at 100 degrees C for 30 minutes can be stored for up to five months at room temperature if protected from light. The preparation is stable for at least two years under refrigeration. PMID:2028996

  8. Chloride in vesicular trafficking and function.

    Science.gov (United States)

    Stauber, Tobias; Jentsch, Thomas J

    2013-01-01

    Luminal acidification is of pivotal importance for the physiology of the secretory and endocytic pathways and its diverse trafficking events. Acidification by the proton-pumping V-ATPase requires charge compensation by counterion currents that are commonly attributed to chloride. The molecular identification of intracellular chloride transporters and the improvement of methodologies for measuring intraorganellar pH and chloride have facilitated the investigation of the physiology of vesicular chloride transport. New data question the requirement of chloride for pH regulation of various organelles and furthermore ascribe functions to chloride that are beyond merely electrically shunting the proton pump. This review surveys the currently established and proposed intracellular chloride transporters and gives an overview of membrane-trafficking steps that are affected by the perturbation of chloride transport. Finally, potential mechanisms of membrane-trafficking modulation by chloride are discussed and put into the context of organellar ion homeostasis in general. PMID:23092411

  9. Electrochemical Chloride extraction using external electrodes?

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Pedersen, Anne Juul

    2006-01-01

    Electrochemical methods for the removal of chloride from concrete have been developed and the methods are primarily designed for situations where corrosion has started due to an increased chloride concentration in the vicinity of the reinforcement. In these methods the reinforcement is used...... as the cathode. However, some unwanted side effects can occur, including alkali-silica reaction and in some cases hydrogen embrittlement. It is also suggested also to use electrochemical chloride extraction in a preventive way in constructions where chloride induced corrosion is likely to be a problem after...... a period of time, i.e. remove the chlorides before the chloride front reaches the reinforcement. If the chlorides are removed from outer few centimetres from the surface, the chloride will not reach the reinforcement and cause damage. By using the electrochemical chloride removal in this preventive way...

  10. Chloride binding of cement-based materials subjected to external chloride environment - A review

    OpenAIRE

    Yuan, Q.; Shi, C; Schutter, G. de; Audenaert, K.; Deng, D.

    2009-01-01

    This paper reviews the chloride binding of cement-based materials subjected to external chloride environments. Chloride ion exist either in the pore solution, chemically bound to the hydration products, or physically held to the surface of the hydration products. Chloride binding of cement-based material is very complicated and influenced by many factors, such as chloride concentration, cement composition, hydroxyl concentration, cation of chloride salt, temperature, supplementary cementing m...

  11. Iron(III)-Catalyzed Ring-Closing Carbonyl-Olefin Metathesis.

    Science.gov (United States)

    Saá, Carlos

    2016-09-01

    Recent developments in catalytic carbonyl-olefin metathesis are summarized in this Highlight. Schindler and co-workers have reported that the environmentally benign FeCl3 catalyst promotes ring-closing carbonyl-olefin metathesis (RCCOM) in high yield under very mild conditions. PMID:27491787

  12. Iron(III)-Catalyzed Ring-Closing Carbonyl-Olefin Metathesis.

    Science.gov (United States)

    Saá, Carlos

    2016-09-01

    Recent developments in catalytic carbonyl-olefin metathesis are summarized in this Highlight. Schindler and co-workers have reported that the environmentally benign FeCl3 catalyst promotes ring-closing carbonyl-olefin metathesis (RCCOM) in high yield under very mild conditions.

  13. Preparation and microwave shielding property of silver-coated carbonyl iron powder

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Xiao Guo, E-mail: xgcao@gdut.edu.cn [School of Materials and Energy, Guangdong University of Technology, Guangzhou 510006, Guangdong (China); Ren, Hao [Guangzhou Research Institute of O-M-E Technology, Guangzhou 510006, Guangdong (China); Zhang, Hai Yan [School of Materials and Energy, Guangdong University of Technology, Guangzhou 510006, Guangdong (China)

    2015-05-15

    Highlights: • The silver-coated carbonyl iron powder is prepared by the electroless plating process. • The silver-coated carbonyl iron powder is a new kind of conductive filler. • The reflection and absorption dominate the shielding mechanism of the prepared powder. • Increasing the thickness of electroconductive adhesive will increase the SE. - Abstract: Electroless silver coating of carbonyl iron powder is demonstrated in the present investigation. The carbonyl iron powders are characterized by scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), and X-ray diffraction analysis (XRD) before and after the coating process. The relatively uniform and continuous silver coating is obtained under the given coating conditions. In this paper, the electromagnetic interference (EMI) shielding mechanism of the silver-coated carbonyl iron powder is suggested. The reflection of silver coating and absorption of carbonyl iron powder dominate the shielding mechanism of the silver-coated carbonyl iron powder. The silver-coated carbonyl iron powders are used as conductive filler in electroconductive adhesive for electromagnetic interference shielding applications. The effect of the thickness of electroconductive adhesive on the shielding effectiveness (SE) is investigated. The results indicate that the SE increases obviously with the increase of the thickness of electroconductive adhesive. The SE of the electroconductive adhesive with 0.35 mm thickness is above 38 dB across the tested frequency range.

  14. Ketene as a Reaction Intermediate in the Carbonylation of Dimethyl Ether to Methyl Acetate over Mordenite

    DEFF Research Database (Denmark)

    Rasmussen, Dominik Bjørn; Christensen, Jakob Munkholt; Temel, Burcin;

    2015-01-01

    Unprecedented insight into the carbonylation of dimethyl ether over Mordenite is provided through the identification of ketene (CH2CO) as a reaction intermediate. The formation of ketene is predicted by detailed DFT calculations and verified experimentally by the observation of doubly deuterated ...... acetic acid (CH2DCOOD), when D2O is introduced in the feed during the carbonylation reaction....

  15. Protein carbonylation after traumatic brain injury: cell specificity, regional susceptibility, and gender differences.

    Science.gov (United States)

    Lazarus, Rachel C; Buonora, John E; Jacobowitz, David M; Mueller, Gregory P

    2015-01-01

    Protein carbonylation is a well-documented and quantifiable consequence of oxidative stress in several neuropathologies, including multiple sclerosis, Alzheimer׳s disease, and Parkinson׳s disease. Although oxidative stress is a hallmark of traumatic brain injury (TBI), little work has explored the specific neural regions and cell types in which protein carbonylation occurs. Furthermore, the effect of gender on protein carbonylation after TBI has not been studied. The present investigation was designed to determine the regional and cell specificity of TBI-induced protein carbonylation and how this response to injury is affected by gender. Immunohistochemistry was used to visualize protein carbonylation in the brains of adult male and female Sprague-Dawley rats subjected to controlled cortical impact (CCI) as an injury model of TBI. Cell-specific markers were used to colocalize the presence of carbonylated proteins in specific cell types, including astrocytes, neurons, microglia, and oligodendrocytes. Results also indicated that the injury lesion site, ventral portion of the dorsal third ventricle, and ventricular lining above the median eminence showed dramatic increases in protein carbonylation after injury. Specifically, astrocytes and limited regions of ependymal cells adjacent to the dorsal third ventricle and the median eminence were most susceptible to postinjury protein carbonylation. However, these patterns of differential susceptibility to protein carbonylation were gender dependent, with males showing significantly greater protein carbonylation at sites distant from the lesion. Proteomic analyses were also conducted and determined that the proteins most affected by carbonylation in response to TBI include glial fibrillary acidic protein, dihydropyrimidase-related protein 2, fructose-bisphosphate aldolase C, and fructose-bisphosphate aldolase A. Many other proteins, however, were not carbonylated by CCI. These findings indicate that there is both regional

  16. Impact of HVAC filter on indoor air quality in terms of ozone removal and carbonyls generation

    Science.gov (United States)

    Lin, Chi-Chi; Chen, Hsuan-Yu

    2014-06-01

    This study aims at detecting ozone removal rates and corresponding carbonyls generated by ozone reaction with HVAC filters from various building, i.e., shopping mall, school, and office building. Studies were conducted in a small-scale environmental chamber. By examining dust properties including organic carbon proportion and specific surface area of dusts adsorbed on filters along with ozone removal rates and carbonyls generation rate, the relationship among dust properties, ozone removal rates, and carbonyls generation was identified. The results indicate a well-defined positive correlation between ozone removal efficiency and carbonyls generation on filters, as well as a positive correlation among the mass of organic carbon on filters, ozone removal efficiency and carbonyls generations.

  17. Development of an automatic sampling device for the continuous measurement of atmospheric carbonyls compounds

    International Nuclear Information System (INIS)

    Two sampling strategies were studied to develop an automatic instrument for the continuous measurement of atmospheric carbonyl compounds. Because of its specificity towards carbonyls compounds, sampling by using a transfer of gaseous phase in a liquid phase associated with a simultaneous chemical derivatization of the trapped compounds was first studied. However, this method do not allow a quantitative sampling of all studied carbonyl compounds, nor a continuous measurement in the field. To overcome the difficulties, a second strategy was investigated: the cryogenic adsorption onto solid adsorbent followed by thermodesorption and a direct analysis by GC/MS. Collection efficiency using different solid adsorbents was found greater than 95% for carbonyl compounds consisting of 1 to 7 carbons. This work is a successful first step towards the realization of the automatic sampling device for a continuous measurement of atmospheric carbonyls compounds. (author)

  18. 1,5-Diaminotetrazolium chloride

    Directory of Open Access Journals (Sweden)

    Ling-Qiao Meng

    2010-04-01

    Full Text Available The title compound, CH5N6+·Cl−, crystallized with two indepedent 1,5-diaminotetrazolium cations and two independent chloride anions in the asymmetric unit. In the crystal, there are a number of N—H...Cl hydrogen-bonding interactions, which generate a three-dimensional network.

  19. Chloride : The queen of electrolytes?

    NARCIS (Netherlands)

    Berend, Kenrick; van Hulsteijn, Leonard Hendrik; Gans, Rijk O. B.

    2012-01-01

    Background: Channelopathies, defined as diseases that are caused by mutations in genes encoding ion channels, are associated with a wide variety of symptoms and have been documented extensively over the past decade. In contrast, despite the important role of chloride in serum, textbooks in general d

  20. Synthesis, characterization and bioactivities of N,O-carbonylated chitosan.

    Science.gov (United States)

    Liu, Hongli; Liu, Xiaoli; Yue, Lin; Jiang, Qixing; Xia, Wenshui

    2016-10-01

    N,O-Carbonylated chitosan derivative (NTCS) was synthesized via oxidation and substitution reaction, respectively. The carboxyethylation of the polysaccharide was identified by Fourier transform infrared (FTIR), (1)H nuclear magnetic resonance (NMR), X-ray diffraction analysis (XRD), Zeta potential measurement and Thermogravimetric analysis (TGA). It is revealed that compared with chitosan (CS), NTCS exhibited an excellent solubility in distilled water, high in vitro bile acid binding capacity, as well as a low viscosity. The in vitro bile acid binding capacity reached 17.21mg/g, which was 4.5-fold higher than that of CS. The results suggest that NTCS may be useful as a potential functional food supplement in food industry or a key ingredient in the pharmaceutical industry. These findings provide important supports for developing new food additive, and expand the scope of application of CS in the food industry. PMID:27189702

  1. Carbonyl Sulfide Isotopologues: Ultraviolet Absorption Cross Sections and Stratospheric Photolysis

    DEFF Research Database (Denmark)

    Danielache, Sebastian Oscar; Nanbu, Shinkoh; Eskebjerg, Carsten;

    2009-01-01

    Ultraviolet absorption cross sections of the main and substituted carbonyl sulfide isotopologues were calculated using wavepacket dynamics. The calculated absorption cross section of 16O12C32S is in very good agreement with the accepted experimental spectrum between 190 and 250 nm. Relative to 16...... can be explained in terms of the change in the norm of the initial wavepacket. Implications for our understanding of the stratospheric sulfur cycle are discussed.......12C32S, isotopic substitution shows a significant enhancement of the cross section for 16O13C32S, a significant reduction for 18O12C32S and 17O12C32S and almost no change for the sulfur isotopologues 16O12C33S, 16O12C34S, and 16O12C36S. The analysis of the initial wavepackets shows that these changes...

  2. Direct Vapor Phase Carbonylation of Methanol over NiCl2/C Catalyst

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    @@ Introduction The carbonylation of alcohols via homogenous catalysis is important in manufacturing acetic acid and higher carboxylic acids and their esters[1,2]. The main route to produce acetic acid is to make methanol carbonylated by means of the Monsanto and BP process in which a homogeneous rhodium catalyst is used. Although the homogeneous carbonylation of methanol is a highly selective process, it is affected by the disadvantages associated with a highly corrosive reaction medium due to the use of methyl iodide as the promoter, and the difficulty of the product separation[3]. The use of a heterogeneous catalyst seems very interesting and attractive to us[4], especially the direct vapor phase carbonylation of methanol without a halide promoter is of considerable importance and is strong incentive economically. There has, however, been very little success in finding either heterogeneous or homogeneous catalysts that can catalyze the reaction effectively without the addition of a promoter[5,6]. According to the known carbonylation mechanism[7,8], the methyl iodide directly carbonylates with CO to from MeCOI which interacts with methanol(MeOH) to produce methyl acetate(MeCOOMe) and HI, and then MeOH reacts with HI to from CH3I. In fact, this carbonylation reaction is the indirect catalytic carbonylation of methanol[9]. In this work, a novel catalyst for the direct vapor phase carbonylation of methanol without the addition of any halide in the feed as a promoter was investigated. Compared to the known liquid phase methanol carbonylation process, some advantages of this vapor phase reaction are as follows:

  3. Microbial reductive dehalogenation of vinyl chloride

    Energy Technology Data Exchange (ETDEWEB)

    Spormann, Alfred M [Stanford, CA; Muller, Jochen A [Baltimore, MD; Rosner, Bettina M [Berlin, DE; Von Abendroth, Gregory [Mannheim, DE; Meshulam-Simon, Galit [Los Angeles, CA; McCarty, Perry L [Stanford, CA

    2014-02-11

    Compositions and methods are provided that relate to the bioremediation of chlorinated ethenes, particularly the bioremediation of vinyl chloride by Dehalococcoides-like organisms. An isolated strain of bacteria, Dehalococcoides sp. strain VS, that metabolizes vinyl chloride is provided; the genetic sequence of the enzyme responsible for vinyl chloride dehalogenation; methods of assessing the capability of endogenous organisms at an environmental site to metabolize vinyl chloride; and a method of using the strains of the invention for bioremediation.

  4. Progress of Carbonation in Chloride Contaminated Concretes

    OpenAIRE

    Wang, Yaocheng; Basheer, P.A.M.; Nanukuttan, S; Bai, Y.

    2016-01-01

    Concretes used in marine environment are generally under the cyclic effect of CO2 and chloride ions (Cl-). To date, the influence of carbonation on ingress of chloride ions in concretes has been widely studied; in comparison, study on the influence of Cl- on the progress of carbonation is limited. During the study, concretes were exposed to independent and combined mechanisms of carbonation and chloride ingress regimes. Profiles of apparent pH and chloride concentration were used to indicate ...

  5. First Magnesium-mediated Carbonyl Benzylation in Water

    Institute of Scientific and Technical Information of China (English)

    DENG,Wei(邓维); TAN,Xiang-Hui(谭翔辉); LIU,Lei(刘磊); GUO,Qing-Xiang(郭庆祥)

    2004-01-01

    Catalyzed by AgNO3, Mg was found for the first time to be able to mediate the coupling reaction between aromatic aldehydes and benzyl bromide or chloride in water. The yields were slightly higher than the recent results for Mg-mediated allylation despite the fact that aqueous benzylation is intrinsically much harder than allylation. It was also found that the coupling reaction was chemoselective for aromatic aldehydes over aliphatic aldehydes, and chemoselective for aromatic aldehydes over aromatic ketones.

  6. Chloride sublimation of gold-arsenic concentrates

    International Nuclear Information System (INIS)

    Present article is devoted to chloride sublimation of gold-arsenic concentrates. The results of studies of chloride sublimation of gold-arsenic comprising concentrates of Chore deposit of Tajikistan are considered. It is found that by application sodium chloride for gold-arsenic comprising concentrates it is possible to extract gold and silver from flotation concentrates.

  7. 21 CFR 172.180 - Stannous chloride.

    Science.gov (United States)

    2010-04-01

    ... Preservatives § 172.180 Stannous chloride. The food additive stannous chloride may be safely used for color... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Stannous chloride. 172.180 Section 172.180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR...

  8. Variation of ambient carbonyl levels in urban Beijing between 2005 and 2012

    Science.gov (United States)

    Chen, Wentai; Shao, Min; Wang, Ming; Lu, Sihua; Liu, Ying; Yuan, Bin; Yang, Yudong; Zeng, Limin; Chen, Zhongming; Chang, Chih-Chung; Zhang, Qian; Hu, Min

    2016-03-01

    Carbonyl compounds are important precursors of secondary air pollutants. With the rapid economic development and the implementation of stricter control measures in Beijing, the sources of carbonyls possibly changed. Based on measurement data obtained at an urban site in Beijing between 2005 and 2012, we investigated annual variations in carbonyl levels and sources during these years. In summer, formaldehyde and acetaldehyde levels decreased significantly at a rate of 9.1%/year and 7.2%/year, respectively, while acetone levels increased at a rate of 4.3%/year. In winter, formaldehyde levels increased and acetaldehyde levels decreased. We also investigated the factors driving the variation in carbonyls levels during summer by determination of emission ratios for carbonyls and their precursors, and calculation of photochemical formation of carbonyls. The relative declines for primary formaldehyde and acetaldehyde levels were larger than those for secondary formation. This is possibly due to the increasing usage of natural gas and liquefied petroleum gas which could result in the rise of carbonyl precursor emission ratios. The increase in acetone levels might be related to the rising solvent usage in Beijing during these years. The influences of these sources should be paid more attention in future research.

  9. Electroless plating preparation and electromagnetic properties of Co-coated carbonyl iron particles/polyimide composite

    Science.gov (United States)

    Zhou, Yingying; Zhou, Wancheng; Li, Rong; Qing, Yuchang; Luo, Fa; Zhu, Dongmei

    2016-03-01

    To solve the serious electromagnetic interference problems at elevated temperature, one thin microwave-absorbing sheet employing Co-coated carbonyl iron particles and polyimide was prepared. The Co-coated carbonyl iron particles were successfully prepared using an electroless plating method. The microstructure, composition, phase and static magnetic properties of Co-coated carbonyl iron particles were characterized by combination of scanning electron microscope (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). The electromagnetic parameters of Co-coated carbonyl iron particles/polyimide composite were measured in the frequency range of 2-18 GHz, and the electromagnetic loss mechanism of the material-obtained was discussed. The microwave absorption properties of composites before and after heat treatment at 300 °C for 100 h were characterized in 2-18 GHz frequency range. It was established that composites based on Co-coated carbonyl iron demonstrate thermomagnetic stability, indicating that Co coating reduces the oxidation of carbonyl iron. Thus, Co-coated carbonyl iron particles/polyimide composites are useful in the design of microwave absorbers operating at temperatures up to 300 °C.

  10. Shock compression of polyvinyl chloride

    Science.gov (United States)

    Neogi, Anupam; Mitra, Nilanjan

    2016-04-01

    This study presents shock compression simulation of atactic polyvinyl chloride (PVC) using ab-initio and classical molecular dynamics. The manuscript also identifies the limits of applicability of classical molecular dynamics based shock compression simulation for PVC. The mechanism of bond dissociation under shock loading and its progression is demonstrated in this manuscript using the density functional theory based molecular dynamics simulations. The rate of dissociation of different bonds at different shock velocities is also presented in this manuscript.

  11. FeCl3 -Catalyzed Ring-Closing Carbonyl-Olefin Metathesis.

    Science.gov (United States)

    Ma, Lina; Li, Wenjuan; Xi, Hui; Bai, Xiaohui; Ma, Enlu; Yan, Xiaoyu; Li, Zhiping

    2016-08-22

    Exploiting catalytic carbonyl-olefin metathesis is an ongoing challenge in organic synthesis. Reported herein is an FeCl3 -catalyzed ring-closing carbonyl-olefin metathesis. The protocol allows access to a range of carbo-/heterocyclic alkenes with good efficiency and excellent trans diastereoselectivity. The methodology presents one of the rare examples of catalytic ring-closing carbonyl-olefin metathesis. This process is proposed to take place by FeCl3 -catalyzed oxetane formation followed by retro-ring-opening to deliver metathesis products. PMID:27431372

  12. FeCl3 -Catalyzed Ring-Closing Carbonyl-Olefin Metathesis.

    Science.gov (United States)

    Ma, Lina; Li, Wenjuan; Xi, Hui; Bai, Xiaohui; Ma, Enlu; Yan, Xiaoyu; Li, Zhiping

    2016-08-22

    Exploiting catalytic carbonyl-olefin metathesis is an ongoing challenge in organic synthesis. Reported herein is an FeCl3 -catalyzed ring-closing carbonyl-olefin metathesis. The protocol allows access to a range of carbo-/heterocyclic alkenes with good efficiency and excellent trans diastereoselectivity. The methodology presents one of the rare examples of catalytic ring-closing carbonyl-olefin metathesis. This process is proposed to take place by FeCl3 -catalyzed oxetane formation followed by retro-ring-opening to deliver metathesis products.

  13. Visible Light-Induced Carbonylation Reactions with Organic Dyes as the Photosensitizers.

    Science.gov (United States)

    Peng, Jin-Bao; Qi, Xinxin; Wu, Xiao-Feng

    2016-09-01

    Dyes can CO do it: Organic dyes and pigments are usually applied in textile dyeing, which can be dated back to the Neolithic period. Interestingly, the possibility to use organic dyes as photoredox catalysts has also been noticed by organic chemists and applied in organic synthesis. Carbonylation reactions as a powerful procedure in carbonyl-containing compound preparation have also been studied. In this manuscript, the recent achievements in using organic dyes as visible-light sensitizers in carbonylation chemistry are summarized and discussed.

  14. [¹¹C]Phosgene: a versatile reagent for radioactive carbonyl insertion into medicinal radiotracers for positron emission tomography.

    Science.gov (United States)

    Roeda, Dirk; Dollé, Frédéric

    2010-01-01

    [¹¹C]Phosgene has been playing a relatively modest but continuous and manifest role all along the history of radiochemistry for Positron Emission Tomography. It acts as a radiolabelling agent through carbonyl insertion, usually between heteroatoms, and benefits from a high chemical reactivity allowing for short reaction times. The aim of this review is to give an overview of this radiochemistry from its beginning until the present day. After drawing up the inventory of the various ways of its production, the reactions in which it has been employed and the labelled products that have been synthesised with it are catalogued. This comprises the reactions of [¹¹C]phosgene with primary, secondary and tertiary amines to labelled isocyanates and carbamoyl chlorides, which serve as intermediates for symmetrical and unsymmetrical [¹¹C]ureas and [¹¹C]carbamates, reactions with alcohols leading to labelled carbamates and carbonates via [¹¹C]chloroformates, cyclisation reactions to heterocycles and the radiochemistry of the secondary radiolabelling agents [¹¹C]urea and diethyl- or dimethyl [¹¹C]carbonate. Apart from this already vast field of chemical possibilities there should be room for extension of the use of [¹¹C]phosgene to other chemistry, notably that of C-¹¹C bond formation. PMID:20583989

  15. Study on microwave absorbing properties of carbonyl-iron composite coating based on PVC and Al sheet

    Science.gov (United States)

    Yuping, Duan; Guangli, Wu; Shuchao, Gu; Shuqing, Li; Guojia, Ma

    2012-05-01

    To suppress the increasingly terrible electromagnetic pollution, microwave absorption coatings based on polyvinyl chloride (PVC) sheet have been fabricated, employing polyurethane varnish (PU) as matrix and carbonyl-iron particle (CIP) as absorbent. The morphology, static magnetic and microwave absorption properties of CIP were characterized by scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and vector network analyzer (VNA), respectively. Bruggeman's equation was introduced to calculate the electromagnetic parameters of materials in the frequency range of 2-18 GHz and the loss mechanisms were discussed. Furthermore, the microwave absorption properties of composite coatings with different component content and thickness were investigated. The results show that the electromagnetic properties of the composite heavily depended on the particle loadings. The minimum reflection peaks of the coatings shift towards the lower frequency region with the increase of CIP content or coating thickness. PVC-based coatings with a component content of 1:7 (PU:CIP mass ratio) in CIP/PU layer, exhibit a minimum reflection loss value of -29 dB at 4 GHz and a permissible reflection loss (RL ≤ -10 dB) frequency band of 2-6 GHz, which is much better than the performance of the common metal-based coatings in the lower frequency.

  16. Human TTR conformation altered by rhenium tris-carbonyl derivatives.

    Science.gov (United States)

    Ciccone, Lidia; Policar, Clotilde; Stura, Enrico A; Shepard, William

    2016-09-01

    Transthyretin (TTR) is a 54 kDa homotetrameric serum protein that transports thyroxine (T4) and retinol. TTR is potentially amyloidogenic due to homotetramer dissociation into monomeric intermediates that self-assemble as amyloid deposits and insoluble fibrils. Most crystallographic structures, including those of amyloidogenic variants show the same tetramer without major variations in the monomer-monomer interface nor in the volume of the interdimeric cavity. Soaking TTR crystals in a solution containing rhenium tris-carbonyl derivatives yields a TTR conformer never observed before. Only one of the two monomers of the crystallographic dimer is significantly altered, and the inner part of the T4 binding cavity is expanded at one end and shrunk at the other. The result redefines the mechanism of allosteric communication between the two sites, suggesting that negative cooperativity is a function of dimer asymmetry, which can be induced through internal or external binding. An aspect that remains unexplained is why the conformational changes are ubiquitous throughout the crystal although the heavy metal content of the derivatized crystals is relatively low. The conformational changes observed, which include Leu(82), may represent a form of TTR better at scavenging β-Amyloid. At a resolution of 1.69Å, with excellent refinement statistics and well defined electron density for all parts of the structure, it is possible to envisage answering important questions that range from protein cooperative behavior to heavy atom induced protein conformational modifications that can result in crystallographic non-isomorphism. PMID:27402536

  17. The oceanic cycle and global atmospheric budget of carbonyl sulfide

    Energy Technology Data Exchange (ETDEWEB)

    Weiss, P.S.

    1994-12-31

    A significant portion of stratospheric air chemistry is influenced by the existence of carbonyl sulfide (COS). This ubiquitous sulfur gas represents a major source of sulfur to the stratosphere where it is converted to sulfuric acid aerosol particles. Stratospheric aerosols are climatically important because they scatter incoming solar radiation back to space and are able to increase the catalytic destruction of ozone through gas phase reactions on particle surfaces. COS is primarily formed at the surface of the earth, in both marine and terrestrial environments, and is strongly linked to natural biological processes. However, many gaps in the understanding of the global COS cycle still exist, which has led to a global atmospheric budget that is out of balance by a factor of two or more, and a lack of understanding of how human activity has affected the cycling of this gas. The goal of this study was to focus on COS in the marine environment by investigating production/destruction mechanisms and recalculating the ocean-atmosphere flux.

  18. Total Synthesis of (-)-Spinosyn A via Carbonylative Macrolactonization.

    Science.gov (United States)

    Bai, Yu; Shen, Xingyu; Li, Yong; Dai, Mingji

    2016-08-31

    Spinosyn A (1), a complex natural product featuring a unique 5,6,5,12-fused tetracyclic core structure, is the major component of spinosad, an organic insecticide and an FDA-approved agent used worldwide. Herein, we report an efficient total synthesis of (-)-spinosyn A with 15 steps in the longest linear sequence and 23 steps total from readily available compounds 14 and 23. The synthetic approach features several important catalytic transformations including a chiral amine-catalyzed intramolecular Diels-Alder reaction to afford 22 in excellent diastereoselectivity, a one-step gold-catalyzed propargylic acetate rearrangement to convert 28 to α-iodoenone 31, an unprecedented palladium-catalyzed carbonylative Heck macrolactonization to form the 5,12-fused macrolactone in one step, and a gold-catalyzed Yu glycosylation to install the challenging β-forosamine. This total synthesis is highly convergent and modular, thus offering opportunities to synthesize spinosyn analogues in order to address the emerging cross-resistance problems. PMID:27510806

  19. Characterization of aura tropospheric emissions spectrometer carbonyl sulfide retrievals

    Directory of Open Access Journals (Sweden)

    L. Kuai

    2013-07-01

    Full Text Available We present a description of the Tropospheric Emission Spectrometer (TES carbonyl sulfide (OCS retrieval algorithm, along with evaluation of the biases and uncertainties against aircraft profiles from the HIPPO campaign and data from the NOAA Mauna Loa site. In general, the OCS retrievals (1 have less than 1.0 degree of freedom for signals (DOFs, (2 are sensitive in the mid-troposphere with a peak sensitivity typically between 300 to 500 hPa, (3 but have much smaller systematic errors from temperature, CO2 and H2O calibrations relative to random errors from measurement noise. Here we estimate the monthly means from TES measurements averaged over multiple years so that random errors are reduced and useful information about OCS seasonal and latitudinal variability can be derived. With this averaging, TES OCS data are found to be consistent (within the calculated uncertainties with NOAA ground observations and HIPPO aircraft measurements. TES OCS data also captures the seasonal and latitudinal variations observed by these in situ data.

  20. Aldol Condensation of Volatile Carbonyl Compounds in Acidic Aerosols

    Science.gov (United States)

    Noziere, B.; Esteve, W.

    2003-12-01

    Reactions of volatile organic compounds in acidic aerosols have been shown recently to be potentially important for organic aerosol formation and growth. Aldol condensation, the acid-catalyzed polymerization of carbonyl compounds, is a likely candidate to enhance the flux of organic matter from the gas phase to the condensed phase in the atmosphere. Until now these reactions have only been characterized for conditions relevant to synthesis (high acidities and liquid phase systems) and remote from atmospheric ones. In this work, the uptake of gas-phase acetone and 2,4\\-pentanedione by sulfuric acid solutions has been measured at room temperature using a Rotated Wetted Wall Reactor coupled to a Mass Spectrometer. The aldol condensation rate constants for 2,4\\-pentanedione measured so far for sulfuric acid solutions between 96 and 70 % wt. display a variation with acidity in agreement with what predicted in the organic chemical literature. The values of these constants, however, are much lower than expected for this compound, and comparable to the ones of acetone. Experiments are underway to complete this study to lower acidities and understand the discrepancies with the predicted reactivity.

  1. Heterogeneous oxidation of carbonyl sulfide on mineral oxides

    Institute of Scientific and Technical Information of China (English)

    LIU YongChun; LIU JunFeng; HE Hong; YU YunBo; XUE Li

    2007-01-01

    Heterogeneous oxidation of carbonyl sulfide (OCS) on mineral oxides including SiO2, Fe2O3, CaO, MgO, ZnO and TiO2, which are the main components of atmospheric particles, were investigated using in situ diffuse reflectance infrared Fourier transform spectroscopy (in situ DRIFTS), ion chromatography (IC), temperature-programmed desorption (TPD), X-ray diffraction (XRD) and Brunauer-Emmett-Teller (BET) methods. The main products and intermediates of the heterogeneous oxidation of OCS on these oxides were identified with in situ DRIFTS and IC. The reaction mechanism and kinetics were also discussed. It is found that the reaction mechanism on these mineral oxides is the same as that on Al2O3 for the same final products and the intermediates at room temperature. Namely, OCS can be catalytically oxidized to produce surface SO42- species and gaseous CO2 through the surface hydrogen thiocarbonate (HSCO2-) and HSO3- species. The activity series for heterogeneous oxidation of OCS follows: Al2O3 ≈ CaO>MgO>TiO2 ≈ ZnO>Fe2O3>SiO2. The specific area, basic hydroxyl and surface basicity of these oxides have effect on the reactivity. This study suggests that heterogeneous reactions of OCS on mineral dust may be an unneglectable sink of OCS.

  2. Seasonal fluxes of carbonyl sulfide in a midlatitude forest

    Science.gov (United States)

    Commane, Róisín; Meredith, Laura K.; Baker, Ian T.; Berry, Joseph A.; Munger, J. William; Montzka, Stephen A.; Templer, Pamela H.; Juice, Stephanie M.; Zahniser, Mark S.; Wofsy, Steven C.

    2015-11-01

    Carbonyl sulfide (OCS), the most abundant sulfur gas in the atmosphere, has a summer minimum associated with uptake by vegetation and soils, closely correlated with CO2. We report the first direct measurements to our knowledge of the ecosystem flux of OCS throughout an annual cycle, at a mixed temperate forest. The forest took up OCS during most of the growing season with an overall uptake of 1.36 ± 0.01 mol OCS per ha (43.5 ± 0.5 g S per ha, 95% confidence intervals) for the year. Daytime fluxes accounted for 72% of total uptake. Both soils and incompletely closed stomata in the canopy contributed to nighttime fluxes. Unexpected net OCS emission occurred during the warmest weeks in summer. Many requirements necessary to use fluxes of OCS as a simple estimate of photosynthesis were not met because OCS fluxes did not have a constant relationship with photosynthesis throughout an entire day or over the entire year. However, OCS fluxes provide a direct measure of ecosystem-scale stomatal conductance and mesophyll function, without relying on measures of soil evaporation or leaf temperature, and reveal previously unseen heterogeneity of forest canopy processes. Observations of OCS flux provide powerful, independent means to test and refine land surface and carbon cycle models at the ecosystem scale.

  3. Teratogenicity and embryotoxicity of nickel carbonyl in Syrian hamsters

    Energy Technology Data Exchange (ETDEWEB)

    Sunderman, F.W. Jr.; Shen, S.K.; Reid, M.C.; Allpass, P.R.

    1980-01-01

    Nickel carbonyl was administered to groups of pregnant hamsters by inhalation on days 4, 5, 6, 7, or 8 of gestation. The dams were killed on day 15 of gestation, and the fetuses were examined for malformations. Exposure to Ni(CO)/sub 4/ on days 4 or 5 of gestation resulted in malformation in 5.5% and 5.8% of the progeny, respectively. Progeny included 9 fetuses with cystic lungs, 7 fetuses with exencephaly, 1 fetus with exencephaly plus fused rib and 1 fetus with anophthalmia plus cleft palate. Hemorrhages into serious cavities were found. In progeny of dams exposed to Ni(CO)/sub 4/ on days 6 or 7 of gestation, there was 1 fetus with fused ribs and there were 2 fetuses with hydronephrosis. In another experiment, pregnant hamsters were exposed to inhalation of Ni(CO)/sub 4/ on day 5 of gestation; these dams were permitted to deliver their litters and to nurse their pups. There was no significant difference in the average number of live pups in the Ni(CO)/sub 4/-exposed litters compared to control litters. Neonatal mortality was increased in Ni(CO)/sub 4/-exposed litters. This study demonstrates that Ni(CO)/sub 4/ is teratogenic and embryotoxic in Syrian hamsters.

  4. Atmospheric Sulfur Cycle Effects of Carbonyl Sulfide (OCS)

    Science.gov (United States)

    McBee, Joshua

    1996-01-01

    Carbonyl Sulfide(OCS) is considered to be one of the major sources of sulfur appearing in the stratosphere due to its relative inertness, about I to 10 yearsl. However, the roles of OCS as well as other reduced sulfur compounds such as carbon disulfide (CS2), hydrogen sulfide (H2S), and dimethyl disulfide(CH3)2S2, are not completely understood in the atmosphenc sulfur cycle. Consequently vely little information is available about the effect of sulfur compounds in the stratosphere. The ability of OCS to penetrate into the stratosphere makes it an excellent tracer for study of the role of the sulfi r cycle in stratospheric chemistry. Previously techniques such as gas chromatography and whole air sampling have been used to measure OCS analytically. Each technique had its drawbacks however, with both being quite slow, and whole air sampling being somewhat unreliable. With molecular spectroscopy, however, it has been found in recent years that the tunable diode laser absorption spectrometer (TDL) provides a very rapid and accurate method of measuring OCS and other trace gases

  5. Carbonyl Sulfide for Tracing Carbon Fluxes Field Campaign Report

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, J. Elliott [Univ. of California, Merced, CA (United States); Berry, Joseph A. [Carnegie Inst. of Science, Stanford, CA (United States); Billesbach, Dave [Univ. of Nebraska, Lincoln, NE (United States); Torn, Margaret S [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Zahniser, Mark [Aerodyne Research, Inc., Billerica, MA (United States); Seibt, Ulrike [Univ. of California, Los Angeles, CA (United States); Maseyk, Kadmiel [Pierre and Marie Curie Univ., Paris (France)

    2016-04-01

    The April-June 2012 campaign was located at the U.S. Department of Energy (DOE)’s Atmospheric Radiation Measurement (ARM) Climate Research Facility Southern Great Plains (SGP) site Central Facility and had three purposes. One goal was to demonstrate the ability of current instrumentation to correctly measure fluxes of atmospheric carbonyl sulfide (COS). The approach has been describe previously as a critical approach to advancing carbon cycle science1,2, but requires further investigation at the canopy scale to resolve ecosystem processes. Previous canopy-scale efforts were limited to data rates of 1Hz. While 1 Hz measurements may work in a few ecosystems, it is widely accepted that data rates of 10 to 20 Hz are needed to fully capture the exchange of traces gases between the atmosphere and vegetative canopy. A second goal of this campaign was to determine if canopy observations could provide information to help interpret the seasonal double peak in airborne observations at SGP of CO2 and COS mixing ratios. A third goal was to detect potential sources and sinks of COS that must be resolved before using COS as a tracer of gross primary productivity (GPP).

  6. Comparison of sampling methods for radiocarbon dating of carbonyls in air samples via accelerator mass spectrometry

    Science.gov (United States)

    Schindler, Matthias; Kretschmer, Wolfgang; Scharf, Andreas; Tschekalinskij, Alexander

    2016-05-01

    Three new methods to sample and prepare various carbonyl compounds for radiocarbon measurements were developed and tested. Two of these procedures utilized the Strecker synthetic method to form amino acids from carbonyl compounds with either sodium cyanide or trimethylsilyl cyanide. The third procedure used semicarbazide to form crystalline carbazones with the carbonyl compounds. The resulting amino acids and semicarbazones were then separated and purified using thin layer chromatography. The separated compounds were then combusted to CO2 and reduced to graphite to determine 14C content by accelerator mass spectrometry (AMS). All of these methods were also compared with the standard carbonyl compound sampling method wherein a compound is derivatized with 2,4-dinitrophenylhydrazine and then separated by high-performance liquid chromatography (HPLC).

  7. Synthesis of 2-Cyclopentenone Derivatives via Palladium-Catalyzed Intramolecular Carbonyl α-Alkenylation.

    Science.gov (United States)

    Chen, Panpan; Meng, Yinggao; Wang, Han; Han, Feipeng; Wang, Yulong; Song, Chuanjun; Chang, Junbiao

    2016-08-01

    2-Cyclopentenone derivatives have been efficiently synthesized from 5-bromo-5-hexen-2-ones via palladium-catalyzed intramolecular carbonyl α-alkenylation followed by double-bond migration under mild reaction conditions. PMID:27463262

  8. Nanostructured palladium tailored via carbonyl chemical route towards oxygen reduction reaction

    International Nuclear Information System (INIS)

    Graphical Abstract: Mass-depending morphologies of nanostructured Palladium obtained via the carbonyl chemical route. Display Omitted -- Highlights: •Mass-depending morphology was observed in nanostructured palladium supported on carbon prepared by the carbonyl chemical route. •The Morphological effect of carbon supported Pd was investigated towards ORR. -- Abstract: Carbon supported palladium nanostructures were synthesized via the carbonyl chemical route. Compared with nanostructured platinum, prepared via carbonyl chemical route, Pd nanomaterials showed mass-loading morphology, whereas particle size and morphology of Pt nanostructures was constant. The oxygen reduction reaction (ORR) on nanostructured Pd, with different morphology in both acid and alkaline medium was investigated. A relationship, based on X-ray diffraction structural analysis pattern, transmission electron microscope, with the Pd morphological effect on ORR activity was identified

  9. Efficient and selective α-bromination of carbonyl compounds with N-bromosuccinimide under microwave

    KAUST Repository

    Guan, Xiao-Yu

    2014-02-07

    A highly efficient method for the synthesis of α-halocarbonyl compounds has been achieved via selective monobromination of aromatic and aliphatic carbonyl compounds with N-bromosuccinimide catalyzed by p-toluenesulfonic acid under microwave irradiation within 30 min.

  10. Ruthenium carbonyl catalyst supported on ceric oxide for preparation of olefins from synthesis gas

    Science.gov (United States)

    Pierantozzi, Ronald

    1985-01-01

    A catalyst comprising a ruthenium carbonyl compound deposited on a cerium oxide-containing support material provides for the selective synthesis of low molecular weight olefinic hydrocarbons from mixtures of hydrogen and carbon monoxide.

  11. Incorporating Cobalt Carbonyl Moieties onto Ethynylthiophene-Based Dithienylcyclopentene Switches. 1. Photochemistry

    NARCIS (Netherlands)

    Harvey, Emma C.; Areephong, Jetsuda; Cafolla, Attilio A.; Long, Conor; Browne, Wesley R.; Pryce, Mary T.; Feringa, Bernard

    2014-01-01

    The synthesis and characterization of a series of dithienyl perhydro- and perfluorocyclopentene photochromic molecular switches appended with cobalt carbonyl binding 3-ethynylthiophene and phenyl-3-ethynylthiophene substituents are reported. Their photochromic properties, fatigue resistance, and the

  12. A carbonyl iron/carbon fiber material for electromagnetic wave absorption.

    Science.gov (United States)

    Youh, Meng-Jey; Wu, Hung-Chih; Lin, Wang-Hua; Chiu, Sheng-Cheng; Huang, Chien-Fa; Yu, Hsin-Chih; Hsu, Jen-Sung; Li, Yuan-Yao

    2011-03-01

    A carbonyl iron/carbon fiber material consisting of carbon fibers grown on micrometer-sized carbonyl iron sphere, was synthesized by chemical vapor deposition using a mixture of C2H2 and H2. The hollow-core carbon fibers (outer diameter: 140 nm and inner diameter: 40 nm) were composed of well-ordered graphene layers which were almost parallel to the long axis of the fibers. A composite (2 mm thick) consisting of the carbonyl iron/carbon fibers and epoxy resin demonstrated excellent electromagnetic (EM) wave absorption. Minimum reflection losses of -36 dB (99.95% of EM wave absorption) at 7.6 GHz and -32 dB (99.92% of EM wave absorption) at 34.1 GHz were achieved. The well-dispersed and network-like carbon fibers in the resin matrix affected the dielectric loss of the EM wave while the carbonyl iron affected the magnetic loss.

  13. Protein carbonylation and aggregation precede neuronal apoptosis induced by partial glutathione depletion

    Directory of Open Access Journals (Sweden)

    Jianzheng Zheng

    2012-04-01

    Full Text Available While the build-up of oxidized proteins within cells is believed to be toxic, there is currently no evidence linking protein carbonylation and cell death. In the present study, we show that incubation of nPC12 (neuron-like PC12 cells with 50 μM DEM (diethyl maleate leads to a partial and transient depletion of glutathione (GSH. Concomitant with GSH disappearance there is increased accumulation of PCOs (protein carbonyls and cell death (both by necrosis and apoptosis. Immunocytochemical studies also revealed a temporal/spatial relationship between carbonylation and cellular apoptosis. In addition, the extent of all three, PCO accumulation, protein aggregation and cell death, augments if oxidized proteins are not removed by proteasomal degradation. Furthermore, the effectiveness of the carbonyl scavengers hydralazine, histidine hydrazide and methoxylamine at preventing cell death identifies PCOs as the toxic species. Experiments using well-characterized apoptosis inhibitors place protein carbonylation downstream of the mitochondrial transition pore opening and upstream of caspase activation. While the study focused mostly on nPC12 cells, experiments in primary neuronal cultures yielded the same results. The findings are also not restricted to DEM-induced cell death, since a similar relationship between carbonylation and apoptosis was found in staurosporine- and buthionine sulfoximine-treated nPC12 cells. In sum, the above results show for the first time a causal relationship between carbonylation, protein aggregation and apoptosis of neurons undergoing oxidative damage. To the best of our knowledge, this is the first study to place direct (oxidative protein carbonylation within the apoptotic pathway.

  14. Fabrication and electromagnetic characteristics of microwave absorbers containing PPY and carbonyl iron composite

    Energy Technology Data Exchange (ETDEWEB)

    Li Dengao, E-mail: lidengao123@163.com [College of Information Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Wang Hongbin; Zhao Jumin [College of Information Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Yang Xiaoli [Department of Electrical and Computer Engineering, Purdue University Calumet, IN 46323-2094 (United States)

    2011-10-17

    Highlights: {yields} Polypyrrole powders are prepared by in situ polymerization method. {yields} Then PPY-carbonyl iron composite with different mixture ratios have been prepared. {yields} The effect of the mass ratio of PPY-carbonyl iron on the microwave loss properties of the composites is investigated. {yields} A possible microwave absorbing mechanism of PPY-carbonyl iron composite has been proposed. - Abstract: The objective of this study is to develop microwave absorbers using both dielectric and magnetic lossy materials. Polypyrrole (PPY) is used as dielectric lossy materials and carbonyl iron particles is used as magnetic lossy materials. Polypyrrole powders are prepared by in situ polymerization method. Then PPY-carbonyl iron composite with different mixture ratios have been prepared by as-prepared material. The structure, morphology and properties of the composites are characterized with IR, XRD, scanning electron microscope (SEM), Net-work Anlyzer. The complex permittivity ({epsilon}{sup '}{sub r}-j{epsilon}{sup ''}{sub r}) and reflection loss (dB) of the composites have been measured at different microwave frequencies in S-band and C-band (30-6000 MHz) employing vector network analyzer model HP 8722ET vector. The effect of the mass ratio of PPY-carbonyl iron on the microwave loss properties of the composites is investigated. A possible microwave absorbing mechanism of PPY-carbonyl iron composite has been proposed. The PPY-carbonyl iron composite can find applications in suppression of electromagnetic interference (EMI), and reduction of radar signature.

  15. Proteomic analysis and protein carbonylation profile in trained and untrained rat muscle

    OpenAIRE

    F.Magherini; P.M. Abruzzo; Puglia, M.; Bini, L.; T. Gamberi; Esposito, F; A. Veicsteinas; Marini, M.; Fiorillo, C; Gulisano, M; Modesti, A

    2012-01-01

    Understanding the relationship between physical exercise, reactive oxygen species and skeletal muscle modification is important in order to better identify the benefits or the damages that appropriate or inappropriate exercise can induce. Unbalanced ROS levels can lead to oxidation of cellular macromolecules and a major class of protein oxidative modification is carbonylation. The aim of this investigation was to study muscle protein expression and carbonylation patterns in tra...

  16. COMPARATIVE STUDY OF EFFICACY OF FERROUS SULPHATE AND CARBONYL IRON IN ANEMIA OF ANTENATAL WOMEN

    Directory of Open Access Journals (Sweden)

    Radhika

    2015-03-01

    Full Text Available Iron deficiency anemia is the most common and important public health problem all over the world in the risk group of antenatal women. Research is going on to improve the iron status of the pregnant women with different forms of iron available. In this regard, Carbonyl Iron is showing promising results in improving the red cell mass with better compliance. 120 antenatal women were recruited in this study. The study comprised of 6weeks for each patient. They were given Carbonyl Iron 100 mg/day and FeS04 100gm/day . Before and after treatment all the baseline and specific investigations were one. Results were tabulated, comparison and significance were tested by unpaired student ’s’ test and their 'p' value was calculated. Results were shown graphically also. Carbonyl Iron showed improvement in hemoglobin, PCV and better than ferrous Sulphate (P <0.001. Incidence of side effects were less with Carbonyl Iron than Ferrous Sulphate, better compliance was seen with Carbonyl Iron. In conclusion, the present study s howed that Carbonyl Iron had better efficacy and safety in the management of Iron deficiency anemia in antenatal women than ferrous Sulphate

  17. Oxidative Stress and Carbonyl Lesions in Ulcerative Colitis and Associated Colorectal Cancer

    Directory of Open Access Journals (Sweden)

    Zhiqi Wang

    2016-01-01

    Full Text Available Oxidative stress has long been known as a pathogenic factor of ulcerative colitis (UC and colitis-associated colorectal cancer (CAC, but the effects of secondary carbonyl lesions receive less emphasis. In inflammatory conditions, reactive oxygen species (ROS, such as superoxide anion free radical (O2∙-, hydrogen peroxide (H2O2, and hydroxyl radical (HO∙, are produced at high levels and accumulated to cause oxidative stress (OS. In oxidative status, accumulated ROS can cause protein dysfunction and DNA damage, leading to gene mutations and cell death. Accumulated ROS could also act as chemical messengers to activate signaling pathways, such as NF-κB and p38 MAPK, to affect cell proliferation, differentiation, and apoptosis. More importantly, electrophilic carbonyl compounds produced by lipid peroxidation may function as secondary pathogenic factors, causing further protein and membrane lesions. This may in turn exaggerate oxidative stress, forming a vicious cycle. Electrophilic carbonyls could also cause DNA mutations and breaks, driving malignant progression of UC. The secondary lesions caused by carbonyl compounds may be exceptionally important in the case of host carbonyl defensive system deficit, such as aldo-keto reductase 1B10 deficiency. This review article updates the current understanding of oxidative stress and carbonyl lesions in the development and progression of UC and CAC.

  18. Protein carbonylation, protein aggregation and neuronal cell death in a murine model of multiple sclerosis

    Science.gov (United States)

    Dasgupta, Anushka

    Many studies have suggested that oxidative stress plays an important role in the pathophysiology of both multiple sclerosis (MS) and its animal model experimental autoimmune encephalomyelitis (EAE). Yet, the mechanism by which oxidative stress leads to tissue damage in these disorders is unclear. Recent work from our laboratory has revealed that protein carbonylation, a major oxidative modification caused by severe and/or chronic oxidative stress conditions, is elevated in MS and EAE. Furthermore, protein carbonylation has been shown to alter protein structure leading to misfolding/aggregation. These findings prompted me to hypothesize that carbonylated proteins, formed as a consequence of oxidative stress and/or decreased proteasomal activity, promote protein aggregation to mediate neuronal apoptosis in vitro and in EAE. To test this novel hypothesis, I first characterized protein carbonylation, protein aggregation and apoptosis along the spinal cord during the course of myelin-oligodendrocyte glycoprotein (MOG)35-55 peptide-induced EAE in C57BL/6 mice [Chapter 2]. The results show that carbonylated proteins accumulate throughout the course of the disease, albeit by different mechanisms: increased oxidative stress in acute EAE and decreased proteasomal activity in chronic EAE. I discovered not only that there is a temporal correlation between protein carbonylation and apoptosis but also that carbonyl levels are significantly higher in apoptotic cells. A high number of juxta-nuclear and cytoplasmic protein aggregates containing the majority of the oxidized proteins are also present during the course of EAE, which seems to be due to reduced autophagy. In chapter 3, I show that when gluthathione levels are reduced to those in EAE spinal cord, both neuron-like PC12 (nPC12) cells and primary neuronal cultures accumulate carbonylated proteins and undergo cell death (both by necrosis and apoptosis). Immunocytochemical and biochemical studies also revealed a temporal

  19. Simple chloride sensors for continuous groundwater monitoring

    DEFF Research Database (Denmark)

    Thorn, Paul; Mortensen, John

    2012-01-01

    The development of chloride sensors which can be used for continuous, on-line monitoring of groundwater could be very valuable in the management of our coastal water resources. However, sensor stability, drift, and durability all need to be addressed in order for the sensors to be used...... in continuous application. This study looks at the development of a simple, inexpensive chloride electrode, and evaluates its performance under continuous use, both in the laboratory and in a field test in a monitoring well. The results from the study showed a consistent response to changing chloride...... sensor remained responsive even at low chloride concentrations, where the conductivity electrode was no longer responding to changing chloride levels. With the results, it is believed that the simple chloride sensor could be used for continuous monitoring of groundwater quality....

  20. Intramolecular Hydrogen Bond in Biologically Active o-Carbonyl Hydroquinones

    Directory of Open Access Journals (Sweden)

    Maximiliano Martínez-Cifuentes

    2014-07-01

    Full Text Available Intramolecular hydrogen bonds (IHBs play a central role in the molecular structure, chemical reactivity and interactions of biologically active molecules. Here, we study the IHBs of seven related o-carbonyl hydroquinones and one structurally-related aromatic lactone, some of which have shown anticancer and antioxidant activity. Experimental NMR data were correlated with theoretical calculations at the DFT and ab initio levels. Natural bond orbital (NBO and molecular electrostatic potential (MEP calculations were used to study the electronic characteristics of these IHB. As expected, our results show that NBO calculations are better than MEP to describe the strength of the IHBs. NBO energies (∆Eij(2 show that the main contributions to energy stabilization correspond to LPàσ* interactions for IHBs, O1…O2-H2 and the delocalization LPàπ* for O2-C2 = Cα(β. For the O1…O2-H2 interaction, the values of ∆Eij(2 can be attributed to the difference in the overlap ability between orbitals i and j (Fij, instead of the energy difference between them. The large energy for the LP O2àπ* C2 = Cα(β interaction in the compounds 9-Hydroxy-5-oxo-4,8, 8-trimethyl-l,9(8H-anthracenecarbolactone (VIII and 9,10-dihydroxy-4,4-dimethylanthracen-1(4H-one (VII (55.49 and 60.70 kcal/mol, respectively when compared with the remaining molecules (all less than 50 kcal/mol, suggests that the IHBs in VIII and VII are strongly resonance assisted.

  1. Metabolism of bupropion by carbonyl reductases in liver and intestine.

    Science.gov (United States)

    Connarn, Jamie N; Zhang, Xinyuan; Babiskin, Andrew; Sun, Duxin

    2015-07-01

    Bupropion's metabolism and the formation of hydroxybupropion in the liver by cytochrome P450 2B6 (CYP2B6) has been extensively studied; however, the metabolism and formation of erythro/threohydrobupropion in the liver and intestine by carbonyl reductases (CR) has not been well characterized. The purpose of this investigation was to compare the relative contribution of the two metabolism pathways of bupropion (by CYP2B6 and CR) in the subcellular fractions of liver and intestine and to identify the CRs responsible for erythro/threohydrobupropion formation in the liver and the intestine. The results showed that the liver microsome generated the highest amount of hydroxybupropion (Vmax = 131 pmol/min per milligram, Km = 87 μM). In addition, liver microsome and S9 fractions formed similar levels of threohydrobupropion by CR (Vmax = 98-99 pmol/min per milligram and Km = 186-265 μM). Interestingly, the liver has similar capability to form hydroxybupropion (by CYP2B6) and threohydrobupropion (by CR). In contrast, none of the intestinal fractions generate hydroxybupropion, suggesting that the intestine does not have CYP2B6 available for metabolism of bupropion. However, intestinal S9 fraction formed threohydrobupropion to the extent of 25% of the amount of threohydrobupropion formed by liver S9 fraction. Enzyme inhibition and Western blots identified that 11β-dehydrogenase isozyme 1 in the liver microsome fraction is mainly responsible for the formation of threohydrobupropion, and in the intestine AKR7 may be responsible for the same metabolite formation. These quantitative comparisons of bupropion metabolism by CR in the liver and intestine may provide new insight into its efficacy and side effects with respect to these metabolites.

  2. Soil fluxes of carbonyl sulfide (COS) across four distinct ecosystems

    Science.gov (United States)

    Sun, W.; Maseyk, K. S.; Lett, C.; Juarez, S.; Kooijmans, L.; Mammarella, I.; Vesala, T.; Chen, H.; Seibt, U.

    2015-12-01

    Soils are additional but poorly resolved sinks of carbonyl sulfide (COS) in terrestrial ecosystems. COS has been proposed as a tracer for quantifying gross photosynthesis based on the coupled stomatal uptake of COS and CO2. But applying this tracer requires the soil COS flux to be subtracted from the ecosystem flux to obtain the actual plant flux. To simulate soil COS fluxes, we have built a 1-D diffusion-reaction model accounting for vertical transport in the soil, microbial sinks and sources, and a litter layer. Uptake and production of COS in the soil column are linked with soil temperature and moisture through empirical functions adapted from enzyme kinetics and lab incubations. We have measured soil COS fluxes and the related soil variables in four distinct ecosystems: a wheat field (Southern Great Plains, OK, USA), an oak woodland (Santa Monica Mountains, CA, USA), a tropical rainforest (La Selva Biological Station, Costa Rica) and a boreal pine forest (Hyytiälä, Finland). Across all sites, a lower soil temperature and a humid climate are generally favorable to soil COS uptake. Strong COS emissions were observed in the wheat field at high soil temperatures after harvesting but were absent in other ecosystems, indicating that COS exchange may behave differently in agricultural soils. We simulated the soil fluxes in all ecosystems using the diffusion-reaction model, and optimized the source/sink strength parameters with field data. The optimized model provides insights that are not attainable from data analysis alone: For example, the wheat field soil must have continued uptake activity even when it showed net emissions, and leaf litter contributed dominantly to the COS sink after rain in the oak woodland. We expect the new model to be useful for simulating global soil COS fluxes as field data on soil fluxes from a broader range of ecosystems become available.

  3. Organometallic and Bioorganometallic Chemistry - Ferrocene and Metal Carbonyls

    Directory of Open Access Journals (Sweden)

    Čakić Semenčić, M.

    2011-02-01

    Full Text Available Organometallic chemistry deals with compounds containing metal-carbon bonds. Basic organometallics derived from the s- and p-block metals (containing solely σ-bonds were understood earlier, while organometallic chemistry of the d- and f-block has developed much more recently. These compounds are characterized by three types of M-C bonds (σ, π and δand their structures are impossible to deduce by chemical means alone; fundamental advances had to await the development of X-ray diffraction, as well as IR- and NMR-spectroscopy. On the other hand, elucidation of the structure of e. g. vitamin B12 and ferrocene (discovered in 1951 contributed to progress in these instrumental analytical methods, influencing further phenomenal success of transition-metal organometallic chemistry in the second half of the twentieth century. The most thoroughly explored fields of application of organometallics were in the area of catalysis, asymmetric synthesis, olefin metathesis, as well as organic synthesis and access to new materials and polymers.The most usual ligands bound to d- and f-metals are carbon monoxide, phosphines, alkyls, carbenes and arenes, and in this review the bonding patterns in the metal carbonyls and ferrocene are elaborated. The common characteristics of these two classes are two-component bonds. The CO-M bonds include (i donation from ligand HOMO to vacant M d-orbitals (σ-bond, and (ii back-donation from the filled M d-orbitals in the ligand LUMO (π-bond. Similar (but much more complicated ferrocene contains delocalized bonds consisting of electron donation from Cp to Fe (σ-bonds- and π-bonding and δ-back-bonding from metal to Cp. In such a way ferrocene, i. e. (η5-Cp2Fe contains 18 bonding electrons giving to this compound "superaromatic" properties in the sense of stability and electrophilic substitution. In contrast to benzenoid aromatic compounds reactions in two Cp-rings can occur giving homo- and heteroannularly mono-, two-… per

  4. ENVIRONMENTAL EXPOSURE TO VINYL CHLORIDE

    Directory of Open Access Journals (Sweden)

    Henryka Langauer-Lewowicka

    2010-09-01

    Full Text Available Vinyl chloride (VC monomer is a wellknown carcinogenic and mutagenic substance causes liver damages, angiosarcoma of the liver, acro – osteolysis, sclerodermalike changes in workers chronically exposed to this gas. There are following VC emitors to the environment: VC production plants, polymerization facilities and planes where polyvinyl products are fabricated. Because of that, the general population is coming into VC contact through polluted air, food and water. VC concentration in all mentioned sites is very low, often not detectable. There was found any health risk for the general population. The VC air concentration in the vicinity to antropogenic emitors is always higher. Such a situation may causes undesirable health effect for residents living in the neighbourhood. Epidemiological studies are performed to detect the adverse VC effect in selected cohorts. Non of the study did not confirmed cases of angiosarcoma among residents living near a vinyl chloride sites. VC production is growing permanently, so VC emission will be higher. Because of that health monitoring of general population and especially of selected groups seems to be necessary in the future.

  5. Iron(III) Chloride mediated reduction of Bis(1-isoquinolylcarbonyl)amide to an Amide

    Indian Academy of Sciences (India)

    Rojalin Sahu; Papuli Chaliha; Vadivelu Manivannan

    2016-01-01

    In methanol, FeCl3 reacted readily with L1H (L1H = bis(1-isoquinolylcarbonyl)amide) and afforded a complex having the formula [Fe(L2)Cl2] (1) {L2− = -((1-isoquinolyl)(methoxy)methyl)isoquinoline-1-carboxamide ion}. This reaction involves reduction of one of the two carbonyl groups present in L1H to (methoxy)methyl group. A plausible mechanism for the conversion of L1H to L2− has been proposed. Determination of molecular structure of 1 confirmed this conversion. Fe(III) ion is surrounded by three nitrogen atoms of the ligand and two chloride ions, imparting a rare distorted trigonal bipyramidal N3Cl2 coordination environment.

  6. Green process to recover magnesium chloride from residue solution of potassium chloride production plant

    Institute of Scientific and Technical Information of China (English)

    Lin WANG; Yunliang HE; Yanfei WANG; Ying BAO; Jingkang WANG

    2008-01-01

    The green process to recover magnesium chlor-ide from the residue solution of a potassium chloride pro-duction plant, which comes from the leach solution of a potash mine in Laos, is designed and optimized. The res-idue solution contains magnesium chloride above 25 wt-%, potassium chloride and sodium chloride together below 5 wt-% and a few other ions such as Br-, SO2-4and Ca2+. The recovery process contains two steps: the previous impurity removal operation and the two-stage evapora-tion-cooling crystallization procedure to produce magnes-ium chloride. The crystallized impurity carnallite obtained from the first step is recycled to the potassium chloride plant to recover the potassium salt. The developed process is a zero discharge one and thus fulfills the requirements for green chemical industrial production. The produced magnesium chloride is up to industrial criteria.

  7. Influence of Chloride-Ion Adsorption Agent on Chloride Ions in Concrete and Mortar

    OpenAIRE

    Gai-Fei Peng; Nai-Qian Feng; Qi-Ming Song

    2014-01-01

    The influence of a chloride-ion adsorption agent (Cl agent in short), composed of zeolite, calcium aluminate hydrate and calcium nitrite, on the ingress of chloride ions into concrete and mortar has been experimentally studied. The permeability of concrete was measured, and the chloride ion content in mortar was tested. The experimental results reveal that the Cl agent could adsorb chloride ions effectively, which had penetrated into concrete and mortar. When the Cl agent was used at a dosage...

  8. Factors influencing chloride deposition in a coastal hilly area and application to chloride deposition mapping

    OpenAIRE

    H. Guan; Love, A. J.; C. T. Simmons; Makhnin, O.; A. S. Kayaalp

    2010-01-01

    Chloride is commonly used as an environmental tracer for studying water flow and solute transport in the environment. It is especially useful for estimating groundwater recharge based on the commonly used chloride mass balance (CMB) method. Strong spatial variability in chloride deposition in coastal areas is one difficulty encountered in appropriately applying the method. A high-resolution bulk chloride deposition map in the coastal region is thus needed. The aim of this study is to construc...

  9. Factors influencing chloride deposition in a coastal hilly area and application to chloride deposition mapping

    OpenAIRE

    H. Guan; Love, A. J.; C. T. Simmons; Makhnin, O.; A. S. Kayaalp

    2010-01-01

    Chloride is commonly used as an environmental tracer for studying water flow and solute transport in the environment. It is especially useful for estimating groundwater recharge based on the commonly used chloride mass balance (CMB) method. Strong spatial variability in chloride deposition in coastal areas is one difficulty encountered in appropriately applying the method. A high-resolution bulk chloride deposition map in the coastal region is thus needed. The aim of this st...

  10. Concentrations of formaldehyde and other carbonyls in environments affected by incense burning.

    Science.gov (United States)

    Ho, Steven Sai Hang; Yu, Jian Zhen

    2002-10-01

    Burning incense to pay homage to deities is common in Chinese homes and temples. Air samples were collected and analyzed for carbonyls from a home and a temple in Hong Kong where incense burning occurs on a daily basis. Carbonyls in the air were trapped on a solid sorbent coated with O-(2,3,4,5,6-pentafluorobenzyl)-hydroxylamine, followed by thermal desorption and subsequent GC/MS analysis. The carbonyls identified include formaldehyde, acetaldehyde, acrolein, 2-furfural, benzaldehyde, glyoxal, and methylglyoxal. The levels of the above carbonyls correlate with the intensity of the incense-burning activities. The total mixing ratios of the carbonyls in the temple exceed those in the ambient air outside the temple by 11-23 times. Formaldehyde is the most abundant species, contributing to approximately 55% of the total carbonyl mixing ratios in both the temple and the home environments during incense burning. The mixing ratio of formaldehyde ranges from 108 to 346 ppbv in the temple and averages 103 ppbv in the home during incense burning. These values exceed the World Health Organization (WHO) air quality guideline of 100 microg m(-3) (88 ppbv) for formaldehyde. The highest formaldehyde level in the temple exceeds the WHO guideline by 3 times at peak incense burning hours. The mixing ratio of acrolein in the temple ranges from 20 to 99 ppbv, approaching or exceeding the WHO air quality guideline of 50 microg m(-3) (22 ppbv) for acrolein. Our measurements indicate that incense burning significantly elevates the concentrations of a number of carbonyls, most notably formaldehyde and acrolein, in the surrounding environments. This study provides preliminary insights on indoor air quality problems created by incense burning.

  11. Proteomic identification of carbonylated proteins in F344 rat hippocampus after 1-bromopropane exposure

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Zhenlie [Department of Occupational and Environmental Health, Nagoya University Graduate School of Medicine, Nagoya 466‐8550 (Japan); Department of Toxicology, Guangdong Prevention and Treatment Center for Occupational Diseases, Guangzhou 510‐300 (China); Ichihara, Sahoko [Graduate School of Regional Innovation Studies, Mie University, Tsu 514‐8507 (Japan); Oikawa, Shinji [Department of Environmental and Molecular Medicine, Mie University Graduate School of Medicine, Mie 514‐8507 (Japan); Chang, Jie; Zhang, Lingyi; Subramanian, Kaviarasan; Mohideen, Sahabudeen Sheik [Department of Occupational and Environmental Health, Nagoya University Graduate School of Medicine, Nagoya 466‐8550 (Japan); Ichihara, Gaku, E-mail: gak@med.nagoya-u.ac.jp [Department of Occupational and Environmental Health, Nagoya University Graduate School of Medicine, Nagoya 466‐8550 (Japan)

    2012-08-15

    1-Bromopropane (1-BP) is neurotoxic in both experimental animals and humans. Previous proteomic analysis of rat hippocampus implicated alteration of protein expression in oxidative stress, suggesting that oxidative stress plays a role in 1-BP-induced neurotoxicity. To understand this role at the protein level, we exposed male F344 rats to 1-BP at 0, 400, or 1000 ppm for 8 h/day for 1 week or 4 weeks by inhalation and quantitated changes in hippocampal protein carbonyl using a protein carbonyl assay, two-dimensional gel electrophoresis (2-DE), immunoblotting, and matrix-assisted laser-desorption ionization time-of-flight mass spectrometry (MALDI-TOF-TOF/MS). Hippocampal reactive oxygen species and protein carbonyl were significantly increased, demonstrating 1-BP-associated induction of oxidative stress and protein damage. MALDI-TOF-TOF/MS identified 10 individual proteins with increased carbonyl modification (p < 0.05; fold-change ≥ 1.5). The identified proteins were involved in diverse biological processes including glycolysis, ATP production, tyrosine catabolism, GTP binding, guanine degradation, and neuronal metabolism of dopamine. Hippocampal triosephosphate isomerase (TPI) activity was significantly reduced and negatively correlated with TPI carbonylation (p < 0.001; r = 0.83). Advanced glycation end-product (AGE) levels were significantly elevated both in the hippocampus and plasma, and hippocampal AGEs correlated negatively with TPI activity (p < 0.001; r = 0.71). In conclusion, 1-BP-induced neurotoxicity in the rat hippocampus seems to involve oxidative damage of cellular proteins, decreased TPI activity, and elevated AGEs. -- Highlights: ► 1-BP increases hippocampal ROS levels and hippocampal and plasma protein carbonyls. ► 1-BP increases TPI carbonylation and decreases TPI activity in the hippocampus. ► 1-BP increases hippocampal and plasma AGE levels.

  12. Positive trends in Southern Hemisphere observations of carbonyl sulfide

    Science.gov (United States)

    Kremser, Stefanie; Jones, Nicholas; Smale, Dan; Palm, Mathias; Lejeune, Bernard; Wang, Yuting; Deutscher, Nicholas

    2016-04-01

    Carbonyl sulfide (OCS; lifetime of about 5.7 years) is the longest lived reduced sulfur-containing gas in the atmosphere. The primary source of OCS is the ocean, which is both a direct source (through OCS emission) and an indirect source (due to oxidation of carbon disulfide, CS2, and dimethyl sulfide). Other natural sources of OCS include volcanic outgassing and direct fluxes from wetland regions. The removal of OCS from the atmosphere is dominated by soil and vegetation uptake, with minor contributions from reactions with the hydroxyl radical. Small anthropogenic sources of OCS are coal combustion, biomass burning, and aluminum production. A dominant indirect source results from CS2 emissions from the rayon industry. Transport of tropospheric OCS to the stratosphere during volcanically quiescent periods has been suggested to contribute sulfur to the stratospheric aerosol layer which affects atmospheric radiative balance. If, however, production of stratospheric aerosols from OCS oxidation is smaller than typical estimates, this OCS contribution would be overestimated. The magnitude of the OCS flux to the stratosphere is currently not well quantified as is the relative contribution of OCS to background aerosol loading. While earlier model simulations indicate OCS fluxes into the atmosphere exceeding removal, past total column observations of OCS show no significant trend. Analysis of tropospheric OCS columns at Arrival Heights (Antarctica) and Lauder (New Zealand) show strong positive trends from 2001-2008 followed by weaker trends to 2015, with unexpected temporal coherence. Since trends in ocean and land sources/sinks at these two sites, respectively, are unlikely to be similar, the coherence in trend structure likely results from changes in transport of OCS from the tropics to middle and high latitudes. Potential causes for OCS increases are (i) increases in tropical lower stratospheric OCS and/or (ii) strengthening of the large-scale circulation which

  13. Quantitative Proteomic Profiling of Muscle Type-Dependent and Age-Dependent Protein Carbonylation in Rat Skeletal Muscle Mitochondria

    OpenAIRE

    Feng, Juan; Xie, Hongwei; Meany, Danni L.; Thompson, LaDora V.; Arriaga, Edgar A.; Griffin, Timothy J.

    2008-01-01

    Carbonylation is a highly prevalent protein modification in skeletal muscle mitochondria, possibly contributing to its functional decline with age. Using quantitative proteomics, we identified mitochondrial proteins susceptible to carbonylation in a muscle type (slow- vs fast-twitch)-dependent and age-dependent manner from Fischer 344 rat skeletal muscle. Fast-twitch muscle contained twice as many carbonylated mitochondrial proteins than did slow-twitch muscle, with 22 proteins showing signif...

  14. Chloride ingress in cement paste and mortar

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede; Hansen, Per Freiesleben; Coats, Alison M.;

    1999-01-01

    modelled on Fick's law modified by a term for chloride binding. Inclusion of chloride binding significantly improves the profile shape of the modelled ingress profiles. The presence of fine aggregate and formation of interfacial transition zones at paste-aggregate boundaries does not significantly affect...

  15. Chloride ingress in cement paste and mortar

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede; Hansen, Per Freiesleben; Coats, Alison M.;

    1999-01-01

    In this paper chloride ingress in cement paste and mortar is followed by electron probe microanalysis. The influence of several paste and exposure parameters on chloride ingress are examined (e.g., water-cement ratio, silica fume addition, exposure time, and temperature), The measurements...

  16. 75 FR 19657 - Barium Chloride From China

    Science.gov (United States)

    2010-04-15

    ... Commission found that the domestic interested party group response to its notice of institution (74 FR 31757... COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Notice of... chloride from China. SUMMARY: The Commission hereby gives notice that it will proceed with a full...

  17. Chloride binding site of neurotransmitter sodium symporters

    DEFF Research Database (Denmark)

    Kantcheva, Adriana Krassimirova; Quick, Matthias; Shi, Lei;

    2013-01-01

    Neurotransmitter:sodium symporters (NSSs) play a critical role in signaling by reuptake of neurotransmitters. Eukaryotic NSSs are chloride-dependent, whereas prokaryotic NSS homologs like LeuT are chloride-independent but contain an acidic residue (Glu290 in LeuT) at a site where eukaryotic NSSs...

  18. Chronopotentiometric chloride sensing using transition time measurement

    NARCIS (Netherlands)

    Abbas, Y.; Graaf, de D.B.; Olthuis, W.; Berg, van den A.

    2013-01-01

    Detection of chloride ions is crucial to accurately access the concrete structure durability[1]. The existing electrochemical method of chloride ions detection in concrete, potentiometry[1], is not suitable for in-situ measurement due to the long term stability issue of conventional reference electr

  19. Chemische contaminanten in diervoeder additief Choline Chloride

    NARCIS (Netherlands)

    Traag, W.A.; Hoogenboom, L.A.P.; Jong, de J.; Egmond, van H.J.; Dam, ten G.

    2010-01-01

    Dit briefrapport beschrijft de resultaten van een onderzoek naar chemische contaminanten in Choline Chloride. De doelstellingen waren: 1) Inzicht te verkrijgen in het voorkomen van (gebromeerde) vlamvertragers en broomdioxines in het diervoederadditief Choline Chloride en het, op basis van de result

  20. Diffusion behavior of chloride ions in concrete

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, T.; Gjoerv, O.E. [Norwegian Univ. of Science and Technology, Trondheim (Norway). Div. of Building Materials

    1996-06-01

    In the present paper, an analysis of the diffusion behavior of chloride ions in concrete is presented. In concentrated electrolytic aqueous solutions such as seawater or that typically used in laboratory experiments, the effect of ionic interaction may significantly reduce the chemical potential and thus the driving force of the diffusing species. Because of different drift velocities of the cations and chloride ions in the solution, the lagging motion of the cations will also retard the drift velocity of the chlorides. In addition, both the electrical double layer forming on the solid surface and the chemical binding may significantly interfere with the transport of the chloride ions. As a result, the diffusion behavior of the chloride ions in concrete is a more complex and complicated transport process than what can be described by Fick`s law of diffusion.

  1. Fructose-Induced Carbonyl/Oxidative Stress in S. cerevisiae: Involvement of TOR.

    Science.gov (United States)

    Valishkevych, Bohdana V; Vasylkovska, Ruslana A; Lozinska, Liudmyla M; Semchyshyn, Halyna M

    2016-01-01

    The TOR (target of rapamycin) signaling pathway first described in the budding yeast Saccharomyces cerevisiae is highly conserved in eukaryotes effector of cell growth, longevity, and stress response. TOR activation by nitrogen sources, in particular amino acids, is well studied; however its interplay with carbohydrates and carbonyl stress is poorly investigated. Fructose is a more potent glycoxidation agent capable of producing greater amounts of reactive carbonyl (RCS) and oxygen species (ROS) than glucose. The increased RCS/ROS production, as a result of glycoxidation in vivo, is supposed to be involved in carbonyl/oxidative stress, metabolic disorders, and lifespan shortening of eukaryotes. In this work we aim to expand our understanding of how TOR is involved in carbonyl/oxidative stress caused by reducing monosaccharides. It was found that in fructose-grown compared with glucose-grown cells the level of carbonyl/oxidative stress markers was higher. The defects in the TOR pathway inhibited metabolic rate and suppressed generation of glycoxidation products in fructose-grown yeast.

  2. Influence of the Dielectric Medium on the Carbonyl Infrared Absorption Peak of Acetylferrocene

    Directory of Open Access Journals (Sweden)

    F. López-Linares

    2005-02-01

    Full Text Available The solvent effect on the position of the carbonyl vibrational stretching ofacetylferrocene in aprotic media was studied in this work. The solvent-induced shifts in thisorganometallic compound were interpreted in terms of the alternative reaction field model(SCRF-MO proposed by Kolling. In contrast to the established trends for carbonyl groupsin organic systems, the results suggest that the continuum models for the reaction field arenot adequate and that the influence of dipolarity-polarizability described by aninhomogeneous coupling function θ (ε L(n 2 that assumes optical dielectric saturation isresponsible for the carbonyl band shift and, there is empirical evidence that the effect offield-induced intermolecular interaction on band shift, interpreted in terms of the van derWaals forces from the solvent, have a important contribution to this phenomena.

  3. Increased carbonylation, protein aggregation and apoptosis in the spinal cord of mice with experimental autoimmune encephalomyelitis

    Directory of Open Access Journals (Sweden)

    Nora I. Perrone‑Bizzozero

    2013-04-01

    Full Text Available Previous work from our laboratory implicated protein carbonylation in the pathophysiology of both MS (multiple sclerosis and its animal model EAE (experimental autoimmune encephalomyelitis. Subsequent in vitro studies revealed that the accumulation of protein carbonyls, triggered by glutathione deficiency or proteasome inhibition, leads to protein aggregation and neuronal cell death. These findings prompted us to investigate whether their association can be also established in vivo. In the present study, we characterized protein carbonylation, protein aggregation and apoptosis along the spinal cord during the course of MOG (myelin-oligodendrocyte glycoprotein35–55 peptide-induced EAE in C57BL/6 mice. The results show that protein carbonyls accumulate throughout the course of the disease, albeit by different mechanisms: increased oxidative stress in acute EAE and decreased proteasomal activity in chronic EAE. We also show a temporal correlation between protein carbonylation (but not oxidative stress and apoptosis. Furthermore, carbonyl levels are significantly higher in apoptotic cells than in live cells. A high number of juxta-nuclear and cytoplasmic protein aggregates containing the majority of the oxidized proteins are present during the course of EAE. The LC3 (microtubule-associated protein light chain 3-II/LC3-I ratio is significantly reduced in both acute and chronic EAE indicating reduced autophagy and explaining why aggresomes accumulate in this disorder. Taken together, the results of the present study suggest a link between protein oxidation and neuronal/glial cell death in vivo, and also demonstrate impaired proteostasis in this widely used murine model of MS.

  4. Ab initio determination of dark structures in radiationless transitions for aromatic carbonyl compounds.

    Science.gov (United States)

    Fang, Wei-Hai

    2008-03-01

    Mechanistic photodissociation of a polyatomic molecule has long been regarded as an intellectually challenging area of chemical physics, the results of which are relevant to atmospheric chemistry, biological systems, and many application fields. Carbonyl compounds play a unique role in the development of our understanding of the spectroscopy, photochemistry, and photophysics of polyatomic molecules and their photodissociation has been the subject of numerous studies over many decades. Upon irradiation, a molecule can undergo internal conversion (IC) and intersystem crossing (ISC) processes, besides photochemical and other photophysical processes. Transient intermediates formed in the IC and ISC radiationless processes, which are termed "dark", are not amenable to detection by conventional light absorption or emission. However, these dark intermediates play critical roles in IC and ISC processes and thus are essential to understanding mechanistic photochemistry of a polyatomic molecule. We have applied the multiconfiguration complete active space self-consistent field (CASSCF) method to determine the dark transient structures involved in radiationless processes for acetophenone and the related aromatic carbonyl compounds. The electronic and geometric structures predicted for the dark states are in a good agreement with those determined by ultrafast electron diffraction experiments. Intersection structure of different electronic states provides a very efficient "funnel" for the IC or ISC process. However, experimental determination of the intersection structure involved in radiationless transitions of a polyatomic molecule is impossible at present. We have discovered a minimum energy crossing point among the three potential energy surfaces (S1, T1, and T2) that appears to be common to a wide variety of aromatic carbonyl compounds with a constant structure. This new type of crossing point holds the key to understanding much about radiationless processes after

  5. Chloride Transport in Undersea Concrete Tunnel

    Directory of Open Access Journals (Sweden)

    Yuanzhu Zhang

    2016-01-01

    Full Text Available Based on water penetration in unsaturated concrete of underwater tunnel, a diffusion-advection theoretical model of chloride in undersea concrete tunnel was proposed. The basic parameters including porosity, saturated hydraulic conductivity, chloride diffusion coefficient, initial water saturation, and moisture retention function of concrete specimens with two water-binder ratios were determined through lab-scale experiments. The variation of chloride concentration with pressuring time, location, solution concentration, initial saturation, hydraulic pressure, and water-binder ratio was investigated through chloride transport tests under external water pressure. In addition, the change and distribution of chloride concentration of isothermal horizontal flow were numerically analyzed using TOUGH2 software. The results show that chloride transport in unsaturated concrete under external water pressure is a combined effect of diffusion and advection instead of diffusion. Chloride concentration increased with increasing solution concentration for diffusion and increased with an increase in water pressure and a decrease in initial saturation for advection. The dominant driving force converted with time and saturation. When predicting the service life of undersea concrete tunnel, it is suggested that advection is taken into consideration; otherwise the durability tends to be unsafe.

  6. Shelf life of unrefrigerated succinylcholine chloride injection.

    Science.gov (United States)

    Boehm, J J; Dutton, D M; Poust, R I

    1984-02-01

    The shelf life of succinylcholine chloride injection at several pH values when stored at room temperature was evaluated. Solutions containing 20 mg/ml of succinylcholine chloride were stored at 25 and 40 degrees C. The reaction was studied at pH values ranging from 3.0 to 4.5. At two-week intervals, the solutions were assayed by high-pressure liquid chromatography. The initial amount of succinylcholine chloride in all samples was 100.1 +/- 2.37% of label claim. Hydrolysis of succinylcholine chloride in unbuffered solutions followed apparent zero-order kinetics. The pH range of maximum stability was found to be from 3.75 to 4.50. Succinylcholine chloride decomposed at a considerably higher rate at 40 degrees C. Allowing for the effects of pH adjustment during manufacture and degradation during shipping, losses of 7.0% and 9.0% potency can be expected after storage at 25 degrees C for four and six weeks, respectively. Succinylcholine Chloride Injection, USP, should be stored in the refrigerator; if unbuffered succinylcholine chloride injection complying with USP pH limits must be stored at room temperature, it should not be kept for longer than four weeks. PMID:6702837

  7. Synthesis of diversely substituted 2-(furan-3-yl)acetates from allenols through cascade carbonylations.

    Science.gov (United States)

    He, Yan; Zhang, Xinying; Fan, Xuesen

    2015-11-21

    Novel synthesis of diversely substituted 2-(furan-3-yl)acetates via palladium-catalyzed one-pot multi-component reactions of allenols, aryl iodides, alcohols, and carbon monoxide has been developed. Notably, the formation of the title compounds features a cascade process combining carbonylation of aryl iodide, alcohoxyl carbonylation of the in situ formed allyl palladium complex, and intramolecular condensation of the α-hydroxyl enone intermediate. Moreover, the 2-(furan-3-yl)acetates obtained herein were found to be ready intermediates for the construction of the biologically significant naphtho[1,2-b]furan-5-ol scaffold. PMID:26399394

  8. Improvement on stability of square planar rhodium (Ⅰ) complexes for carbonylation of methanol to acetic acid

    Institute of Scientific and Technical Information of China (English)

    蒋华; 潘平来; 袁国卿; 陈新滋

    1999-01-01

    A series of square planar cis-dicarbonyl polymer coordinated rhodium complexes with uncoordinated donors near the central rhodium atoms for carbonylation of methanol to acetic acid are reported. Data of IR, XPS and thermal analysis show that these complexes are very stable. The intramolecular substitution reaction is proposed for their high stability. These complexes show excellent catalytic activity, selectivity and less erosion to the equipment for the methanol carbonylation to acetic acid. The distillation process may be used instead of flash vaporization in the manufacture of acetic acid, which reduces the investment on the equipment.

  9. Kinetics of Vapor—Phase Carbonylation of Ethanol on Ni—Zn/C Catalyst

    Institute of Scientific and Technical Information of China (English)

    PENGFeng

    2002-01-01

    A novel heterogeneous Ni-Zn/C catalyst was used for vapor-phase carbonylation of ethanol under atmospheric pressure.Experiments were designed with the elimination of mass-transfer resistances.The data of primary reaction in the carbonylation were collected with a differential tubular reactor.Power law rate models were emplyed to express the conversion of ethanol and the yields of ethyl propionated and diethyl ether.The results obtained with the models were in agreement with the experimental data.

  10. Activation of Carbonyl-Containing Molecules with Solid Lewis Acids in Aqueous Media

    Energy Technology Data Exchange (ETDEWEB)

    Román-Leshkov, Yuriy [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States). Chemical Engineering; Davis, Mark E. [California Inst. of Technology (CalTech), Pasadena, CA (United States). Chemical Engineering

    2011-09-28

    Current interest in reacting carbonyl-containing molecules in aqueous media is primarily due to the growing emphasis on conversion of biomass to fuels and chemicals. Recently, solid Lewis acids have been shown to perform catalytic reactions with carbonyl-containing molecules such as sugars in aqueous media. Here, catalysis mediated by Lewis acids is briefly discussed, Lewis acid solids that perform catalysis in aqueous media are then described, and the review is concluded with a few comments on the outlook for the future.

  11. Hydrolysis of Carbonyl Sulfide in Binary Mixture of Diethylene Glycol Diethyl Ether and Water

    Institute of Scientific and Technical Information of China (English)

    李新学; 刘迎新; 魏雄辉

    2005-01-01

    The solubility and hydrolysis of carbonyl sulfide in binary mixture of diethylene glycol diethyl ether and water are studied as a function of composition. The use of an aqueous solution of diethylene glycol diethyl ether enhances the solubility and hydrolysis rate of carbonyl sulfide compared with that in pure water. The composition of the mixture with maximum hydrolysis rate varies with temperature. The thermophysical properties including density, viscosity, and surface tension as a function of composition at 20℃ under atmospheric pressure as well as liquid-liquid equilibrium (LLE) data over the temperature range from 28℃ to 90℃ are also measured for the binary mixture.

  12. First application of supported ionic liquid phase (SILP) catalysis for continuous methanol carbonylation

    DEFF Research Database (Denmark)

    Riisager, Anders; Jørgensen, Betina; Wasserscheid, Peter

    2006-01-01

    A solid, silica-supported ionic liquid phase (SILP) rhodium iodide Monsanto-type catalyst system, [BMIM][Rh(CO)(2)I-2]-[BMIM]I -SiO2, exhibits excellent activity and selectivity towards acetyl products in fixed-bed, continuous gas-phase methanol carbonylation.......A solid, silica-supported ionic liquid phase (SILP) rhodium iodide Monsanto-type catalyst system, [BMIM][Rh(CO)(2)I-2]-[BMIM]I -SiO2, exhibits excellent activity and selectivity towards acetyl products in fixed-bed, continuous gas-phase methanol carbonylation....

  13. Ab initio MO study of reaction mechanism for carbonyl migration of Co complex

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Ab initio method under the effective core potential (ECP) approximation is employed to study the reaction mechanism of carbonyl migration of the cycle of olefin hydroformylation catalyzed by a carbonyl cobalt HCo(CO)3 at Hartree-Fock (HF) level. The structures of the reactant, transition state and product for the reaction are determined. The energy of each stationary point is corrected at MP2/LAN2DZ//LANL2DZ+ZPE (zero-point energy) level. The calculated activation barrier is 28.89 kJ/mol.

  14. Impaired cardiac SIRT1 activity by carbonyl stress contributes to aging-related ischemic intolerance.

    Directory of Open Access Journals (Sweden)

    Chunhu Gu

    Full Text Available Reactive aldehydes can initiate protein oxidative damage which may contribute to heart senescence. Sirtuin 1 (SIRT1 is considered to be a potential interventional target for I/R injury management in the elderly. We hypothesized that aldehyde mediated carbonyl stress increases susceptibility of aged hearts to ischemia/reperfusion (I/R injury, and elucidate the underlying mechanisms with a focus on SIRT1. Male C57BL/6 young (4-6 mo and aged (22-24 mo mice were subjected to myocardial I/R. Cardiac aldehyde dehydrogenase (ALDH2, SIRT1 activity and protein carbonyls were assessed. Our data revealed that aged heart exhibited increased endogenous aldehyde/carbonyl stress due to impaired ALDH2 activity concomitant with blunted SIRT1 activity (P<0.05. Exogenous toxic aldehydes (4-HNE exposure in isolated cardiomyocyte verified that aldehyde-induced carbonyl modification on SIRT1 impaired SIRT1 activity leading to worse hypoxia/reoxygenation (H/R injury, which could all be rescued by Alda-1 (ALDH2 activator (all P<0.05. However, SIRT1 inhibitor blocked the protective effect of Alda-1 on H/R cardiomyocyte. Interestingly, myocardial I/R leads to higher carbonylation but lower activity of SIRT1 in aged hearts than that seen in young hearts (P<0.05. The application of Alda-1 significantly reduced the carbonylation on SIRT1 and markedly improved the tolerance to in vivo I/R injury in aged hearts, but failed to protect Sirt1(+/- knockout mice against myocardial I/R injury. This was verified by Alda-1 treatment improved postischemic contractile function recovery in ex vivo perfused aged but not in Sirt1(+/- hearts. Thus, aldehyde/carbonyl stress is accelerated in aging heart. These results provide a new insight that impaired cardiac SIRT1 activity by carbonyl stress plays a critical role in the increased susceptibility of aged heart to I/R injury. ALDH2 activation can restore this aging-related myocardial ischemic intolerance.

  15. POLYMER—SUPPORTED RHODIUM CATALYSTS FOR CARBONYLATION OF METHYL ACETATE TO ACETIC ANHYDRIDE

    Institute of Scientific and Technical Information of China (English)

    CHENDean; HUANGShizhuan; 等

    1993-01-01

    Two kinds of rhodium catalysts supported on cross-linked styrene-divinylbenzene copolymers containing bipyridine or o-phenylene diamine have been prepared and found to display high activity for methyl acetate carbonylation to form acetic anhydride,the activities are even higher than their homogeneous counterparts. XPS analysis was used to characterize the synthetic catalysts.The apparent activation parameters were determined to be Eα=73.3KJ/mol,ΔH≠=66.3KJ/mol,ΔS≠=-28.6eu.These parameters are very close to those in methanol carbonylation and imply to have analogous mechanism in both cases.

  16. Factors influencing chloride deposition in a coastal hilly area and application to chloride deposition mapping

    Directory of Open Access Journals (Sweden)

    H. Guan

    2010-05-01

    Full Text Available Chloride is commonly used as an environmental tracer for studying water flow and solute transport in the environment. It is especially useful for estimating groundwater recharge based on the commonly used chloride mass balance (CMB method. Strong spatial variability in chloride deposition in coastal areas is one difficulty encountered in appropriately applying the method. A high-resolution bulk chloride deposition map in the coastal region is thus needed. The aim of this study is to construct a chloride deposition map in the Mount Lofty Ranges (MLR, a coastal hilly area of approximately 9000 km2 spatial extent in South Australia. We examined geographic (related to coastal distance, orographic, and atmospheric factors that may influence chloride deposition, using partial correlation and regression analyses. The results indicate that coastal distance, elevation, as well as terrain aspect and slope, appear to be significant factors controlling chloride deposition in the study area. Coastal distance accounts for 70% of spatial variability in bulk chloride deposition, with elevation, terrain aspect and slope an additional 15%. The results are incorporated into a de-trended residual kriging model (ASOADeK to produce a 1 km×1 km resolution bulk chloride deposition and concentration maps. The average uncertainty of the deposition map is about 20–30% in the western MLR, and 40–50% in the eastern MLR. The maps will form a useful basis for examining catchment chloride balance for the CMB application in the study area.

  17. Reliability-Based Planning of Chloride Measurements

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Engelund, S.

    1996-01-01

    on measurements of the chloride content obtained from the given structure. In the present paper optimal planning of measurements of the chloride content in reinforced concrete structures is considered. It is shown how optimal experimental plans can be obtained using FORM-analysis. Bayesian statistics are used......In reinforced concrete structures corrosion is initiated when the chloride concentration around the reinforcement exceeds a threshold value. If corrosion starts then expensive repairs can be necessary. The estimation of the probability that corrosion has been initiated in a given structure is based...

  18. Binary Nucleation of Water and Sodium Chloride

    Energy Technology Data Exchange (ETDEWEB)

    Nemec, Thomas [Institute of Thermomechanics ASCR, Prague, Czech Republic; Marsik, Frantisek [Institute of Thermomechanics ASCR, Prague, Czech Republic; Palmer, Donald [ORNL

    2005-01-01

    Nucleation processes in the binary water-sodium chloride system are investigated in the sense of the classical nucleation theory (CNT). The CNT is modified to be able to handle the electrolytic nature of the system and is employed to investigate the acceleration of the nucleation process due to the presence of sodium chloride in the steam. This phenomenon, frequently observed in the Wilson zone of steam turbines, is called early condensation. Therefore, the nucleation rates of the water-sodium chloride mixture are of key importance in the power cycle industry.

  19. Synthesis of the [beta]-D-glucosyl ester of [carbonyl-[sup 13]C]-indole-3-acetic acid

    Energy Technology Data Exchange (ETDEWEB)

    Jakas, A.; Magnus, V. (Rudjer Boskovic Inst., Zagreb (Croatia)); Horvat, S.; Sandberg, G. (Swedish Univ. of Agricultural Sciences, Uppsala (Sweden))

    1993-10-01

    An efficient, operationally simple synthetic approach to 1-O-([carbonyl-[sup 13]C]-indole-3'-ylacetyl)-[beta]-D-glucopyranose is described. The synthesis was carried out by fusing a fully benzylated 1-O-glucosylpseudourea intermediate with [carbonyl-[sup 13]C]-indole-3-acetic acid, followed by hydrogenolytic removal of the protective groups. (Author).

  20. Regiospecific oxidation of an alkyl group of aromatic amine to carbonyl group by DDQ in aq.medium

    Institute of Scientific and Technical Information of China (English)

    Madhav S. Mane; Ravi S. Balaskar; Sandip N. Gavade; Pramod N. Pabrekar; Murlidhar S. Shingare; Dhananjay V. Mane

    2011-01-01

    The regiospecific oxidation of alkyl group of both sterically hindered and unhindered aromatic amine to corresponding carbonyl compound was done in aq. medium by using DDQ. The optimized reaction protocol was found to be most simple, high yielding and novel method for oxidation of alkyl group of aromatic amine in to its carbonyl compound.

  1. Enhanced antioxidation and electromagnetic properties of Co-coated flaky carbonyl iron particles prepared by electroless plating

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Yingying, E-mail: zyzlchappy1989@163.com [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an, Shaanxi 710072 (China); Zhou, Wancheng [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an, Shaanxi 710072 (China); Li, Rong [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an, Shaanxi 710072 (China); No. 603 Faculty, Xi’an Institute of High Technology, Xi’an 710025 (China); Mu, Yang; Qing, Yuchang [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an, Shaanxi 710072 (China)

    2015-07-15

    Highlights: • Co-coated carbonyl iron particles were prepared by electroless plating method. • The obvious weight gain of carbonyl iron was deferred to 400 °C after Co-coated. • The permeability of the Co-coated particle composite kept almost invariable. • Co-coated carbonyl iron composite reserves a better absorption after heat treatment. - Abstract: Co was successfully coated on the surface of flaky carbonyl iron particles using an electroless plating method. The morphologies, composition, as well as magnetic, antioxidation and electromagnetic properties of the samples were characterized by scanning electron microscope (SEM), energy dispersive spectrometer (EDS), vibrating sample magnetometer (VSM), thermogravimetric (TG) and microwave network analyzer. TG curve shows that the obvious weight gain of carbonyl iron was deferred from 300 to 400 °C after Co-coated. In contrast to raw carbonyl iron, the Co-coated carbonyl iron shows better stability on electromagnetic properties after 300 °C heat treatment for 10 h, demonstrating that the Co coating can act as the protection of carbonyl iron.

  2. Mitochondrial ATP synthase is a target for TNBS-induced protein carbonylation in XS-106 dendritic cells.

    Science.gov (United States)

    Je, Jeong Hwan; Lee, Tae Hyung; Kim, Dong Hyun; Cho, Young Hun; Lee, Ju Hee; Kim, Soo Chan; Lee, Sang-Kyou; Lee, Jaewon; Lee, Min-Geol

    2008-06-01

    ROS are produced in dendritic cells (DCs) during antigen presentation in contact hypersensitivity (CHS). As a result, ROS cause a number of nonenzymatic protein modifications, including carbonylation, which is the most widely used marker of oxidative stress. 2,4,6-Trinitrobenzene sulfonic acid (TNBS) is a well-characterized contact allergen that results in the formation of ROS. However, proteins that are carbonylated in DCs in response to TNBS have not been identified. To study ROS-dependent protein carbonylation in response to TNBS, we used the well-established mouse DC line, XS-106. We focused on the effects of TNBS on oxidation by examining selected oxidative markers. We identified TNBS-induced ROS and myeloperoxidase (MPO) proteins and demonstrated that the increase in ROS resulted in IL-12 production. The increase in oxidation was further confirmed by an oxidation-dependent increase in protein modifications, such as carbonylation. In fact, TNBS strongly induced carbonylation of mitochondrial adenosine triphosphate (ATP) synthase in XS-106 DCs, as determined by MALDI-TOF analysis and 2-D Western blotting. ROS production and protein carbonylation were confirmed in human monocyte-derived DCs (Mo-DCs). Furthermore, glutathione (GSH) decreased ROS and protein carbonylation in Mo-DCs. Carbonylation of ATP synthase in DCs may contribute to the pathophysiology of CHS.

  3. Green Synthesis and Regioselective Control of Sn/I2 Mediated Allylation of Carbonyl Compounds with Crotyl Halide in Water

    Institute of Scientific and Technical Information of China (English)

    ZHANG,Yan; ZHA,Zhang-Gen; ZHOU,Yu-Qing; WANG,Zhi-Yong

    2004-01-01

    @@ Barbier-type carbonyl allylation is particularly useful due to ease of operation and the availability and tractability of allylic substrates,[1] Metals such as indium, zinc and tin are often used as the mediator. Here we present a green approach toward the synthesis, that is, Sn/I2 mediated allylation of carbonyl compounds with crotyl halide in water.

  4. Dormancy alleviation by NO or HCN leading to decline of protein carbonylation levels in apple (Malus domestica Borkh.) embryos.

    Science.gov (United States)

    Krasuska, Urszula; Ciacka, Katarzyna; Dębska, Karolina; Bogatek, Renata; Gniazdowska, Agnieszka

    2014-08-15

    Deep dormancy of apple (Malus domestica Borkh.) embryos can be overcome by short-term pre-treatment with nitric oxide (NO) or hydrogen cyanide (HCN). Dormancy alleviation of embryos modulated by NO or HCN and the first step of germination depend on temporary increased production of reactive oxygen species (ROS). Direct oxidative attack on some amino acid residues or secondary reactions via reactive carbohydrates and lipids can lead to the formation of protein carbonyl derivatives. Protein carbonylation is a widely accepted covalent and irreversible modification resulting in inhibition or alteration of enzyme/protein activities. It also increases the susceptibility of proteins to proteolytic degradation. The aim of this work was to investigate protein carbonylation in germinating apple embryos, the dormancy of which was removed by pre-treatment with NO or HCN donors. It was performed using a quantitative spectrophotometric method, while patterns of carbonylated protein in embryo axes were analyzed by immunochemical techniques. The highest concentration of protein carbonyl groups was observed in dormant embryos. It declined in germinating embryos pre-treated with NO or HCN, suggesting elevated degradation of modified proteins during seedling formation. A decrease in the concentration of carbonylated proteins was accompanied by modification in proteolytic activity in germinating apple embryos. A strict correlation between the level of protein carbonyl groups and cotyledon growth and greening was detected. Moreover, direct in vitro carbonylation of BSA treated with NO or HCN donors was analyzed, showing action of both signaling molecules as protein oxidation agents.

  5. Photopromoted carbonylation of olefins with carbon dioxide and labelling studies with 13CO2 and 13CH3OH

    Institute of Scientific and Technical Information of China (English)

    YIN Jingmei; GAO Dabin; HU Jiehan; ZHOU Guangyun; JIA Yingping; WANG Xiangsheng

    2003-01-01

    Photopromoted carbonylation of olefins with carbon dioxide can be completed in ambient conditions (room temperatures and atmospheric pressure) by Co(OAc)2 catalysis. It was found that in carbonyl carbons of methyl ester of aliphatic acid 50% is from CO2 and the other 50% from CH3OH by labelling experimental with 13CO2 and 13CH3OH.

  6. Surface adsorption in strontium chloride ammines

    DEFF Research Database (Denmark)

    Ammitzbøll, Andreas L.; Lysgaard, Steen; Klukowska, Agata;

    2013-01-01

    An adsorbed state and its implications on the ab- and desorption kinetics of ammonia in strontium chloride ammine is identified using a combination of ammonia absorption measurements, thermogravimetric analysis, and density functional theory calculations. During thermogravimetric analysis, ammoni...

  7. Catastrophic event modeling. [lithium thionyl chloride batteries

    Science.gov (United States)

    Frank, H. A.

    1981-01-01

    A mathematical model for the catastrophic failures (venting or explosion of the cell) in lithium thionyl chloride batteries is presented. The phenomenology of the various processes leading to cell failure is reviewed.

  8. Telomerization of Vinyl Chloride with Chloroform Initiated by Ferrous Chloride-Dimethylacetamide under Ultrasonic Conditions

    Directory of Open Access Journals (Sweden)

    Hua Qian

    2015-01-01

    Full Text Available Telomerization of vinyl chloride with chloroform was investigated using ferrous chloride-dimethylacetamide system, and 42.1% yield, more than four times the one reported before, was achieved. The addition of ultrasound further improved the reaction and yield was raised to 51.9% with trace byproducts at highly reduced reaction time and temperature. Ferrous chloride-dimethylacetamide under ultrasonic irradiation acts as a very efficient catalyst system for the 1 : 1 telomerization.

  9. Factors influencing chloride deposition in a coastal hilly area and application to chloride deposition mapping

    OpenAIRE

    H. Guan; Love, A. J.; C. T. Simmons; A. S. Kayaalp

    2009-01-01

    Chloride is commonly used as an environmental tracer for studying water flow and solute transport in the environment. It is especially useful for estimating groundwater recharge based on the commonly used chloride mass balance (CMB) method. Strong spatial variability in chloride deposition in coastal areas is one difficulty encountered in appropriately applying the CMB approach. Furthermore, intensive vegetation clearance for agriculture, for example during the European settlement in many...

  10. Estimating the chloride transport in cement paste

    OpenAIRE

    Princigallo, A.

    2012-01-01

    A method was developed to measure the diffusion coefficient of chloride ions in cement paste based on an analytical solution to Fick’s 2nd law in a cylindrical coordinate system. This natural method yielded diffusivity results within as little as a month. Testing time was reduced by exploiting the three-dimensional inward flux in the specimen. In an attempt to determine the saturation concentration, dense portland cement pastes were exposed to a concentrated chloride solution. The method prov...

  11. Influence of Chloride-Ion Adsorption Agent on Chloride Ions in Concrete and Mortar

    Directory of Open Access Journals (Sweden)

    Gai-Fei Peng

    2014-04-01

    Full Text Available The influence of a chloride-ion adsorption agent (Cl agent in short, composed of zeolite, calcium aluminate hydrate and calcium nitrite, on the ingress of chloride ions into concrete and mortar has been experimentally studied. The permeability of concrete was measured, and the chloride ion content in mortar was tested. The experimental results reveal that the Cl agent could adsorb chloride ions effectively, which had penetrated into concrete and mortar. When the Cl agent was used at a dosage of 6% by mass of cementitious materials in mortar, the resistance to the penetration of chloride ions could be improved greatly, which was more pronounced when a combination of the Cl agent and fly ash or slag was employed. Such an effect is not the result of the low permeability of the mortar, but might be a result of the interaction between the Cl agent and the chloride ions penetrated into the mortar. There are two possible mechanisms for the interaction between the Cl agent and chloride ion ingress. One is the reaction between calcium aluminate hydrate in the Cl agent and chloride ions to form Friedel’s salt, and the other one is that calcium aluminate hydrate reacts with calcium nitrite to form AFm during the early-age hydration of mortar and later the NO2− in AFm is replaced by chloride ions, which then penetrate into the mortar, also forming Friedel’s salt. More research is needed to confirm the mechanisms.

  12. Effect of Chloride Type on Penetration of Chloride Ions in Concrete

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The influence of chloride type on the diffusivity of chloride ions in concrete was studied by experiment. The result shows that the glectric resistance of concrete and the chloride diffusion coefficient are influenced by chloride type. For the same water/cement ratio (W/C), the diffusion coefficient D in KCl solution is larger than that in NaCl solution; however, the concrete resistance in KCl solution is smaller than that in NaCl solution. The experimental result is analyzed with theory of diffusion.

  13. Efficient and selective α-bromination of carbonyl compounds with N-bromosuccinimide under microwave

    Directory of Open Access Journals (Sweden)

    Xiao-Yu Guan

    2015-11-01

    Full Text Available A highly efficient method for the synthesis of α-halocarbonyl compounds has been achieved via selective monobromination of aromatic and aliphatic carbonyl compounds with N-bromosuccinimide catalyzed by p-toluenesulfonic acid under microwave irradiation within 30 min.

  14. Proteomic and carbonylation profile analysis of rat skeletal muscles following acute swimming exercise.

    Directory of Open Access Journals (Sweden)

    Francesca Magherini

    Full Text Available Previous studies by us and other groups characterized protein expression variation following long-term moderate training, whereas the effects of single bursts of exercise are less known. Making use of a proteomic approach, we investigated the effects of acute swimming exercise (ASE on protein expression and carbonylation patterns in two hind limb muscles: the Extensor Digitorum Longus (EDL and the Soleus, mostly composed of fast-twitch and slow-twitch fibres, respectively. Carbonylation is one of the most common oxidative modifications of proteins and a marker of oxidative stress. In fact, several studies suggest that physical activity and the consequent increase in oxygen consumption can lead to increase in reactive oxygen and nitrogen species (RONS production, hence the interest in examining the impact of RONS on skeletal muscle proteins following ASE. Results indicate that protein expression is unaffected by ASE in both muscle types. Unexpectedly, the protein carbonylation level was reduced following ASE. In particular, the analysis found 31 and 5 spots, in Soleus and EDL muscles respectively, whose carbonylation is reduced after ASE. Lipid peroxidation levels in Soleus were markedly reduced as well. Most of the decarbonylated proteins are involved either in the regulation of muscle contractions or in the regulation of energy metabolism. A number of hypotheses may be advanced to account for such results, which will be addressed in future studies.

  15. Magnetically Recoverable Supported Ruthenium Catalyst for Hydrogenation of Alkynes and Transfer Hydrogenation of Carbonyl Compounds

    Science.gov (United States)

    A ruthenium (Ru) catalyst supported on magnetic nanoparticles (NiFe2O4) has been successfully synthesized and used for hydrogenation of alkynes at room temperature as well as transfer hydrogenation of a number of carbonyl compounds under microwave irradiation conditions. The cata...

  16. Magnetic Silica-Supported Ruthenium Nanoparticles: An Efficient Catalyst for Transfer Hydrogenation of Carbonyl Compounds

    Science.gov (United States)

    One-pot synthesis of ruthenium nanoparticles on magnetic silica is described which involve the in situ generation of magnetic silica (Fe3O4@ SiO2) and ruthenium nano particles immobilization; the hydration of nitriles and transfer hydrogenation of carbonyl compounds occurs in hi...

  17. α-Regioselective Barbier Reaction of Carbonyl Compounds and Allyl Halides Mediated by Praseodymium.

    Science.gov (United States)

    Wu, San; Li, Ying; Zhang, Songlin

    2016-09-01

    The first utility of praseodymium as a mediating metal in the Barbier reaction of carbonyl compounds with allyl halides was reported in this paper. In contrast to the traditional metal-mediated or catalyzed Barbier reactions, exclusive α-adducts were obtained in this one-pot reaction with a broad scope of substrates and feasible reaction conditions. PMID:27490708

  18. Levels, sources and health risks of carbonyls and BTEX in the ambient air of Beijing, China

    Institute of Scientific and Technical Information of China (English)

    Yujie Zhang; Yujing Mu; Junfeng Liu; Abdelwahid Mellouki

    2012-01-01

    The atmospheric concentrations of carbonyls and BTEX (benzene,toluene,ethylbenzene,m,p-xylene and o-xylene) were measured simultaneously at a same sampling site in Beijing from September 2008 to August 2010.The average concentrations of the total measured carbonyls during autumn,winter,spring,and summer were 37.7,31.3,39.7,50.5 μg/m3,respectively,and maximal values for their diurnal variations usually happened at noontime.In contrast to carbonyls,the average concentrations of the total measured BTEX during the four seasons were 27.2,31.9,23.2,19.1 μg/m3,respectively,and minimal values for their diurnal variations always occurred in the early afternoon.The average concentration for carbonyls increased about 24% from September 2008-August 2009 to September 2009-August 2010,for BTEX,increased about 15%.Integrated life time cancer risks for three carcinogens (benzene,formaldehyde and acetaldehyde) in Beijing exceeded the value of 1E-06,and the hazard quotient (HQ) of non-cancer risk of exposure to formaldehyde exceeded unity.

  19. The Palladium-Catalyzed Vinylation and Carbonylation of Bromoindoles and N-Acety1-bromoindoline

    OpenAIRE

    Kasahara, Akira; Izumi, Taeko; Ogata, Hideaki

    1989-01-01

    Abstracts The palladium-catalyzed vinylic substitution reaction of alkenes has been shown to proceed in moderate yields with 5- and 6-bromoindols, and N-acetyl-5-bromoindoline. 4-, 5-, 6-, and 7-Bromoindoles also undergo facile palladium-assisted carbonylation with carbon monoxide in methanol to produce methoxycarbonylindoles in moderate yields.

  20. Palladium-catalyzed carbonylative sonogashira coupling of aryl bromides using near stoichiometric carbon monoxide

    DEFF Research Database (Denmark)

    Neumann, Karoline T.; Laursen, Simon R.; Lindhardt, Anders T.;

    2014-01-01

    A general procedure for the palladium-catalyzed carbonylative Sonogashira coupling of aryl bromides is reported, using near stoichiometric amounts of carbon monoxide. The method allows a broad substrate scope in moderate to excellent yields. The formed alkynone motive serves as a platform for...

  1. Synthesis, spectroscopic characterizations, crystal structures and DFT studies of nalidixic acid carbonyl hydrazones derivatives

    Science.gov (United States)

    Bergamini, F. R. G.; Ribeiro, M. A.; Lancellotti, M.; Machado, D.; Miranda, P. C. M. L.; Cuin, A.; Formiga, A. L. B.; Corbi, P. P.

    2016-09-01

    This article describes the synthesis and characterization of the 1-ethyl-7-methyl-4-oxo-1,4-dihydro-1,8-naphthyridine-3-carbohydrazide (hzd) and six carbonyl hydrazones derivatives of the nalidixic with 1H-pyrrol-2-ylmethylidene (hpyrr), 1H-imidazol-2-ylmethylidene (h2imi), pyridin-2-ylmethylidene (h2py), pyridin-3-ylmethylidene (h3py), pyridin-4-ylmethylidene(h4py) and (2-hydroxyphenyl)methylidene (hsali). The carbonyl hydrazones were characterized by elemental and ESI-QTOF-MS analyses, IR and detailed NMR spectroscopic measurements. The 2D NMR experiments allowed the unambiguous assignment of the hydrogen, carbon and nitrogen atoms, which have not been reported for nalidixic acid carbonyl hydrazone derivatives so far. Crystal structures of hzd and the new carbonyl hydrazones h2imi, hpyrr and h3py were determined by X-ray diffraction studies. Although the synthesis of hzd was reported decades ago, the hzd crystal structure have not been reported yet. Geometric optimizations of all the characterized structures were performed with the aid of DFT studies. Despite the fact that the hydrazones with 2-pyridine carboxylic acid (h2py) and salicyl aldehyde (hsali) were already reported by literature, a detailed spectroscopic study followed by DFT studies are also reported for such compounds in this manuscript. Antimicrobial studies of the compounds are also presented.

  2. Heterogeneous Chemistry of Carbonyls and Alcohols With Sulfuric Acid: Implications for Secondary Organic Aerosol Formation

    Science.gov (United States)

    Zhao, J.; Levitt, N.; Zhang, R.

    2006-12-01

    Recent environmental chamber studies have suggested that acid-catalyzed particle-phase reactions of organic carbonyls lead to multifold increases in secondary organic aerosol (SOA) mass and acid-catalyzed reactions between alcohols and aldehydes in the condensed phase lead to the formation of hemiacetals and acetals, also enhancing secondary organic aerosol growth. The kinetics and mechanism of the heterogeneous chemistry of carbonyls and alcohols with sulfuric acid, however, remain largely uncertain. In this talk, we present measurements of heterogeneous uptake of several carbonyls and alcohols on liquid H2SO4 in a wide range of acid concentrations and temperatures. The results indicate that uptake of larger carbonyls is explained by aldol condensation. For small dicarbonyls, heterogeneous reactions are shown to decrease with acidity and involve negligible formation of sulfate esters. Hydration and polymerization likely explain the measured uptake of such small dicarbonyls on H2SO4 and the measurements do not support an acid- catalyzed uptake. Atmospheric implications from our findings will be discussed.

  3. Direct photolysis of carbonyl compounds dissolved in cloud and fog~droplets

    Science.gov (United States)

    Epstein, S. A.; Tapavicza, E.; Furche, F.; Nizkorodov, S. A.

    2013-09-01

    Gas-phase photolysis is an important tropospheric sink for many carbonyl compounds; however the significance of direct photolysis of these compounds dissolved in cloud and fog droplets is uncertain. We develop a theoretical approach to assess the importance of aqueous photolysis for a series of carbonyls that possess carboxyl and hydroxyl functional groups by comparison with rates of other atmospheric processes. We use computationally and experimentally derived effective Henry's law constants, hydration equilibrium parameters, aqueous hydroxyl radical (OH) rate constants, and optical extinction coefficients to identify types of compounds that will (or will not) have competitive aqueous photolysis rates. We also present molecular dynamics simulations designed to estimate gas- and aqueous-phase extinction coefficients of unstudied atmospherically relevant compounds found in d-limonene and isoprene secondary organic aerosol. In addition, experiments designed to measure the photolysis rate of glyceraldehyde, an atmospherically relevant water-soluble organic compound, reveal that aqueous quantum yields are highly molecule-specific and cannot be extrapolated from measurements of structurally similar compounds. We find that only two out of the 92 carbonyl compounds investigated, pyruvic acid and acetoacetic acid, may have aqueous photolysis rates that exceed the rate of oxidation by dissolved OH. For almost all carbonyl compounds lacking α,β-conjugation that were investigated, atmospheric removal by direct photolysis in cloud and fog droplets can be neglected under typical atmospheric conditions.

  4. Ketene as a Reaction Intermediate in the Carbonylation of Dimethyl Ether to Methyl Acetate over Mordenite

    DEFF Research Database (Denmark)

    Rasmussen, Dominik Bjørn; Christensen, Jakob Munkholt; Temel, Burcin;

    2015-01-01

    Unprecedented insight into the carbonylation of dimethyl ether over Mordenite is provided through the identification of ketene (CH2CO) as a reaction intermediate. The formation of ketene is predicted by detailed DFT calculations and verified experimentally by the observation of doubly deuterated...

  5. [pi] Backbonding in Carbonyl Complexes and Carbon-Oxygen Stretching Frequencies: A Molecular Modeling Exercise

    Science.gov (United States)

    Montgomery, Craig D.

    2007-01-01

    An exercise is described that has illustrated the effect of various factors on [pi] backbonding to carbonyl ligands, where the students can view the molecular orbitals corresponding to the M-CO [pi] interaction as well as the competing interaction between the metal and co-ligands. The visual and hands-on nature of the modeling exercise has helped…

  6. Weak carbonyl-methyl intermolecular interactions in acetone clusters explored by IR plus VUV spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Guan, Jiwen [MOE Key Laboratory of Laser Life Science and Institute of Laser Life Science, College of Biophotonics, South China Normal University, Guangzhou 510631 (China); Hu, Yongjun, E-mail: yjhu@scnu.edu.cn [MOE Key Laboratory of Laser Life Science and Institute of Laser Life Science, College of Biophotonics, South China Normal University, Guangzhou 510631 (China); Xie, Min [MOE Key Laboratory of Laser Life Science and Institute of Laser Life Science, College of Biophotonics, South China Normal University, Guangzhou 510631 (China); Bernstein, Elliot R. [Department of Chemistry, Colorado State University, Fort Collins, CO 80523-1872 (United States)

    2012-09-11

    Highlights: Black-Right-Pointing-Pointer The carbonyl overtone of acetone clusters is observed by IR-VUV spectroscopy. Black-Right-Pointing-Pointer Acetone molecules in the dimer are stacked with an antiparallel way. Black-Right-Pointing-Pointer The structure of the acetone trimer and the tetramer are the cyclic structures. Black-Right-Pointing-Pointer The carbonyl groups would interact with the methyl groups in acetone clusters. Black-Right-Pointing-Pointer These weak interactions are further confirmed by H/D substitution experiment. -- Abstract: Size-selected IR-VUV spectroscopy is employed to detect vibrational characteristics in the region 2850 {approx} 3550 cm{sup -1} of neutral acetone and its clusters (CH{sub 3}COCH{sub 3}){sub n} (n = 1-4). Features around 3440 cm{sup -1} in the spectra of acetone monomer and its clusters are assigned to the carbonyl stretch (CO) overtone. These features red-shift from 3455 to 3433 cm{sup -1} as the size of the clusters increases from the monomer to the tetramer. Based on calculations, the experimental IR spectra in the C=O overtone region suggest that the dominant structures for the acetone trimer and tetramer should be cyclic in the supersonic expansion sample. This study also suggests that the carbonyl groups interact with the methyl groups in the acetone clusters. These weak interactions are further confirmed by the use of deuterium substitution.

  7. Palladium-Catalyzed Carbonylation of Primary Amines in Supercritical Carbon Dioxide

    Institute of Scientific and Technical Information of China (English)

    李金恒; 江焕峰; 陈鸣才

    2001-01-01

    The chemoselectity of the palladimm-catalyzed carbonylation of amines was affected by the addition of MeOH in supercritical carbon dioxide. The results show different selectivity in supercritical carbon dioxide CO2(sc) from that in alcohol.Methyl carbamate and its derivatives were obtained in high yields in CO2(sc).

  8. Towards a General Understanding of Carbonyl-Stabilised Ammonium Ylide-Mediated Epoxidation Reactions.

    Science.gov (United States)

    Novacek, Johanna; Roiser, Lukas; Zielke, Katharina; Robiette, Raphaël; Waser, Mario

    2016-08-01

    The key factors for carbonyl-stabilised ammonium ylide-mediated epoxidation reactions were systematically investigated by experimental and computational means and the hereby obtained energy profiles provide explanations for the observed experimental results. In addition, we were able to identify the first tertiary amine-based chiral auxiliary that allows for high enantioselectivities and high yields for such epoxidation reactions.

  9. Infrared Spectroscopic Study of the Adsorption Forms of Cyanuric Acid and Cyanuric Chloride on TiO2.

    Science.gov (United States)

    Chien, Tzu-En; Li, Kun-Lin; Lin, Po-Yuan; Lin, Jong-Liang

    2016-05-31

    Cyanuric acid is often found to be the end product in the hydrolysis of waste melamine and in the TiO2-mediated photocatalytic decomposition of s-triazine-containing compounds used as herbicides or dyes. The photocatalytically recalcitrant nature of cyanuric acid on TiO2 may be closely related to its adsorption properties, including the tautomeric forms present on the surfaces and their bonding structures, which remain to be determined. In this paper, we present the optimized adsorption structures of the four tautomeric isomers (triketo, diketo, monoketo, and triol) of cyanuric acid on a model rutile-TiO2(110) surface and their vibrational absorptions. Experimentally, the adsorption structures of cyanuric acid and chloride on powdered TiO2 are analyzed on the basis of the theoretically obtained, characteristic infrared information. Cyanuric acid on TiO2 at 35 °C exists in triketo and hydroxylated forms, but the diketo becomes the predominant form on the surface at 250 °C, being bonded to a titanium site via one of its carbonyl groups and with a N-H···O hydrogen bonding interaction. Hydroxylation of cyanuric chloride occurs as it is adsorbed on TiO2 at 35 °C. Upon being heated to 200 °C, the surface is mainly covered with the diketo form of cyanuric acid after the adsorption of cyanuric chloride. PMID:27176610

  10. 21 CFR 178.3290 - Chromic chloride complexes.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Chromic chloride complexes. 178.3290 Section 178... SANITIZERS Certain Adjuvants and Production Aids § 178.3290 Chromic chloride complexes. Myristo chromic chloride complex and stearato chromic chloride complex may be safely used as release agents in the...

  11. 49 CFR 179.102-17 - Hydrogen chloride, refrigerated liquid.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrogen chloride, refrigerated liquid. 179.102-17...) § 179.102-17 Hydrogen chloride, refrigerated liquid. Each tank car used to transport hydrogen chloride... on or after March 16, 2009 used for the transportation of hydrogen chloride, refrigerated...

  12. Evaluation of hazardous airborne carbonyls on a university campus in southern China.

    Science.gov (United States)

    Ho, Steven Sai Hang; Ip, Ho Sai Simon; Ho, Kin Fai; Ng, Louisa Pan Ting; Dai, W T; Cao, Junji; Chan, Chi Sing; Ho, Legolas Baggio

    2014-08-01

    A comprehensive assessment of indoor carbonyl compounds for the academic staff workers, and students was conducted on a university campus in Xiamen, China. A total of 15 representative environment categories, including 12 indoor workplaces and three residential units, were selected. The potential indoor pollution sources were identified based on the variability in the molar compositions and correlation analyses for the target carbonyls. Furnishing materials, cooking emissions, and electronic equipment, such as photocopiers, can generate various carbonyls in the workplace. Comparison studies were conducted in the clerical offices, demonstrating that off-gases from wooden furniture and lacquer coatings, environmental tobacco smoke (ETS), and the use of cleaning reagents elevated the indoor carbonyl levels. The measured concentrations of formaldehyde and acetaldehyde in most locations surpassed the exposure limit levels. The lifetime cancer hazard risk (R) associated with formaldehyde was above the concern risk level (1 x 10(-6)) in all of the workplaces. The results indicate that formaldehyde exposure is a valid occupational health and safety concern. Wooden furniture and refurbishing materials can pose serious health threats to occupants. The information in this study could act as a basis for future indoor air quality monitoring in Mainland China. Implications: A university campus represents a microscale city environment consisting of all the working, living, and commercial needs of staff and students. The scope of this investigation covers 21 hazardous carbonyl species based on samples collected from 15 categories of workplaces and residential building in a university campus in southern China. Findings of the study provide a comprehensive assessment of indoor air quality with regards to workers' health and safety. No similar study has been carried out in China. PMID:25185393

  13. Oxi-DIGE: A novel proteomic approach for detecting and quantifying carbonylated proteins.

    Science.gov (United States)

    Baraibar, Martin; Ladouce, Romain; Friguet, Bertrand

    2014-10-01

    Proteins are involved in key cellular functions and our health and wellness depends on their quality. Accumulation of oxidatively damaged proteins is a hallmark of deleterious processes such increased oxidative stress, chronic inflammation, ageing and age-related diseases. Thus, quantifying and identifying oxidized proteins is a biomarker of choice for monitoring biological ageing and/or the efficiency of anti-oxidant, ant-inflammatory and anti-ageing therapies. However, the absence of reliable tools for analyses has inhibited its establishment as the gold standard for measuring the efficacy of anti-ageing and age related diseases interventions. Herein, we present a novel proteomics technology, named Oxi-DIGE?, which provides a significant improvement in terms of specificity, reproducibility and statistical support for proteomic analysis of carbonylated proteins. In Oxi-DIGE, protein carbonyls are labelled with fluorescent hydrazide probes that bind specifically to carbonyl groups in proteins. Experimental groups (e.g. control and experimental samples) are labelled with different flurophore-binded hydrazides that fluoresce light at different wavelengths, producing different colour fluorescence. Thus samples from different experimental groups are co-resolved on a single 2D gel. Increased accuracy is provided due to: (i) reduced false positives by using an exogenous synthetic fluorescent tag; (ii) multiplexing, that is the possibility to run multiple samples on the same gel, (iii) the use of an internal standard on each gel which eliminates inter-gel variations and provides an increased statistical confidence. In addition, the resolution of the carbonyl groups is improved, forming distinct spots that can be identified by mass spectrometry. ?Patent Application (M. Baraibar, R. Ladouce., B. Friguet, A method for detecting and/or quantifying carbonylated proteins (WO/2012/175519) filed by UPMC and referring to the technology described in this abstract. PMID:26461312

  14. Factors influencing chloride deposition in a coastal hilly area and application to chloride deposition mapping

    Directory of Open Access Journals (Sweden)

    H. Guan

    2009-09-01

    Full Text Available Chloride is commonly used as an environmental tracer for studying water flow and solute transport in the environment. It is especially useful for estimating groundwater recharge based on the commonly used chloride mass balance (CMB method. Strong spatial variability in chloride deposition in coastal areas is one difficulty encountered in appropriately applying the CMB approach. Furthermore, intensive vegetation clearance for agriculture, for example during the European settlement in many coastal areas of Australia, may have perturbed catchment chloride balance conditions for appropriate use in CMB applications. In order to deal with these issues, a high resolution chloride deposition map in the coastal region is needed. In this study, we examined geographic, orographic, and atmospheric factors influencing chloride deposition in the Mount Lofty Ranges (MLR, a coastal hilly area of approximately 9000 km2 spatial extent in South Australia, using partial correlation and regression analyses. The results indicate that coastal distance, and terrain aspect and slope are two most significant factors controlling chloride deposition. Coastal distance accounts for 65% spatial variability in chloride deposition, with terrain aspect and slope for 8%. The deposition gradient is about 0.08 gm-2 year-1 km-1 as one progresses inland. The results are incorporated into a published de-trended residual kriging approach (ASOADeK to produce a 1 km×1 km resolution annual chloride deposition map and a bulk precipitation chloride concentration map. The average uncertainty of the deposition map is about 30% in the western MLR, and over 50% in the eastern MLR. The maps will form a very useful basis for examining catchment chloride balances for use in the CMB application in the study area.

  15. Inhibition of nitrite-induced toxicity in channel catfish by calcium chloride and sodium chloride

    Science.gov (United States)

    Tommasso J.R., Wright; Simco, B.A.; Davis, K.B.

    1980-01-01

    Environmental chloride has been shown to inhibit methemoglobin formation in fish, thereby offering a protective effect against nitrite toxicity. Channel catfish (Ictalurus punctatus) were simultaneously exposed to various environmental nitrite and chloride levels (as either CaCl2 or NaCl) in dechlorinated tap water (40 mg/L total hardness, 47 mg/L alkalinity, 4 mg/L chloride, pH = 6.9-7.1, and temperature 21-24°C). Methemoglobin levels in fish simultaneously exposed to 2.5 mg/L nitrite and up to 30 mg/L chloride as either CaCl2 or NaCl were similar but significantly lower than in unprotected fish. Exposure to 10 mg/L nitrite and 60 mg/L chloride resulted in methemoglobin levels similar to those of the controls; most unprotected fish died. Fish exposed to 10 mg/L nitrite had significantly lower methemoglobin levels when protected with 15.0 mg/L chloride as CaCl2 than with NaCl. Fish exposed to nitrite in the presence of 60 mg/L chloride (as either CaCl2 or NaCl) had similar 24-h LC50 values that were significantly elevated above those obtained in the absence of chloride. Calcium had little effect on tolerance to nitrite toxicity in channel catfish in contrast to its large effect reported in steelhead trout (Salmo gairdneri).

  16. Congenital Chloride Diarrhea: Diagnosis by Easy-Accessible Chloride Measurement in Feces

    Directory of Open Access Journals (Sweden)

    C. Gils

    2016-01-01

    Full Text Available Background. Congenital chloride diarrhea (CCD is an autosomal recessive disorder caused by mutations in the genes encoding the intestinal Cl−/HCO3- exchanger and is clinically characterized by watery, profound diarrhea, electrolyte disturbances, and metabolic alkalosis. The CCD diagnosis is based on the clinical symptoms and measurement of high chloride concentration in feces (>90 mmol/L and is confirmed by DNA testing. Untreated CCD is lethal, while long-term clinical outcome improves when treated correctly. Case Presentation. A 27-year-old woman had an emergency caesarian due to pain and discomfort in gestational week 36 + 4. The newborn boy had abdominal distension and yellow fluid per rectum. Therapy with intravenous glucose and sodium chloride decreased his stool frequency and improved his clinical condition. A suspicion of congenital chloride diarrhea was strongly supported using blood gas analyzer to measure an increased chloride concentration in the feces; the diagnosis was confirmed by DNA testing. Discussion. Measurement of chloride in feces using an ordinary blood gas analyzer can serve as a preliminary analysis when congenital chloride diarrhea is suspected. This measurement can be easily performed with a watery feces composition. An easy-accessible chloride measurement available will facilitate the diagnostics and support the initial treatment if CCD is suspected.

  17. Amine and Titanium (IV Chloride, Boron (III Chloride or Zirconium (IV Chloride-Promoted Baylis-Hillman Reactions

    Directory of Open Access Journals (Sweden)

    Shi-Cong Cui

    2001-10-01

    Full Text Available The Baylis-Hillman reactions of various aryl aldehydes with methyl vinyl ketone at temperatures below -20oC using Lewis acids such as titanium (IV chloride, boron (III chloride or zirconium (IV chloride in the presence of a catalytic amount of selected amines used as a Lewis bases afford the chlorinated compounds 1 as the major product in very high yields. Acrylonitrile can also undergo the same reaction to give the corresponding chlorinated product in moderate yield. A plausible reaction mechanism is proposed. However, if the reaction was carried out at room temperature (ca. 20oC, then the Z-configuration of the elimination product 3, derived from 1, was formed as the major product.

  18. Identification, quantification, and functional aspects of skeletal muscle protein-carbonylation in vivo during acute oxidative stress.

    Science.gov (United States)

    Fedorova, Maria; Kuleva, Nadezhda; Hoffmann, Ralf

    2010-05-01

    Reactive oxidative species (ROS) play important roles in cellular signaling but can also modify and often functionally inactivate other biomolecules. Thus, cells have developed effective enzymatic and nonenzymatic strategies to scavenge ROS. However, under oxidative stress, ROS production is able to overwhelm the scavenging systems, increasing the levels of functionally impaired proteins. A major class of irreversible oxidative modifications is carbonylation, which refers to reactive carbonyl-groups. In this investigation, we have studied the production and clearance rates for skeletal muscle proteins in a rat model of acute oxidative stress over a time period of 24 h using a gel-based proteomics approach. Optimized ELISA and Western blots with 10-fold improved sensitivities showed that the carbonylation level was stable at 4 nmol per mg protein 3 h following ROS induction. The carbonylation level then increased 3-fold over 6 h and then remained stable. In total, the oxidative stress changed the steady state levels of 20 proteins and resulted in the carbonylation of 38 skeletal muscle proteins. Carbonylation of these proteins followed diverse kinetics with some proteins being highly carbonylated very quickly, whereas others peaked in the 9 h sample or continued to increase up to 24 h after oxidative stress was induced. PMID:20377239

  19. Chloride equilibrium potential in salamander cones

    Directory of Open Access Journals (Sweden)

    Bryson Eric J

    2004-12-01

    Full Text Available Abstract Background GABAergic inhibition and effects of intracellular chloride ions on calcium channel activity have been proposed to regulate neurotransmission from photoreceptors. To assess the impact of these and other chloride-dependent mechanisms on release from cones, the chloride equilibrium potential (ECl was determined in red-sensitive, large single cones from the tiger salamander retinal slice. Results Whole cell recordings were done using gramicidin perforated patch techniques to maintain endogenous Cl- levels. Membrane potentials were corrected for liquid junction potentials. Cone resting potentials were found to average -46 mV. To measure ECl, we applied long depolarizing steps to activate the calcium-activated chloride current (ICl(Ca and then determined the reversal potential for the current component that was inhibited by the Cl- channel blocker, niflumic acid. With this method, ECl was found to average -46 mV. In a complementary approach, we used a Cl-sensitive dye, MEQ, to measure the Cl- flux produced by depolarization with elevated concentrations of K+. The membrane potentials produced by the various high K+ solutions were measured in separate current clamp experiments. Consistent with electrophysiological experiments, MEQ fluorescence measurements indicated that ECl was below -36 mV. Conclusions The results of this study indicate that ECl is close to the dark resting potential. This will minimize the impact of chloride-dependent presynaptic mechanisms in cone terminals involving GABAa receptors, glutamate transporters and ICl(Ca.

  20. Dynamic Electrochemical Measurement of Chloride Ions.

    Science.gov (United States)

    Abbas, Yawar; de Graaf, Derk B; Olthuis, Wouter; van den Berg, Albert

    2016-02-05

    This protocol describes the dynamic measurement of chloride ions using the transition time of a silver silver chloride (Ag/AgCl) electrode. Silver silver chloride electrode is used extensively for potentiometric measurement of chloride ions concentration in electrolyte. In this measurement, long-term and continuous monitoring is limited due to the inherent drift and the requirement of a stable reference electrode. We utilized the chronopotentiometric approach to minimize drift and avoid the use of a conventional reference electrode. A galvanostatic pulse is applied to an Ag/AgCl electrode which initiates a faradic reaction depleting the Cl- ions near the electrode surface. The transition time, which is the time to completely deplete the ions near the electrode surface, is a function of the ion concentration, given by the Nernst equation. The square root of the transition time is in linear relation to the chloride ion concentration. Drift of the response over two weeks is negligible (59 µM/day) when measuring 1 mM [Cl-]using a current pulse of 10 Am(-2). This is a dynamic measurement where the moment of transition time determines the response and thus is independent of the absolute potential. Any metal wire can be used as a pseudo-reference electrode, making this approach feasible for long-term measurement inside concrete structures.

  1. Recherches récentes sur le cobalt carbonyle et ses dérivés Recent Studies of Cobalt Carbonyl and Its Derivatives

    Directory of Open Access Journals (Sweden)

    Poilblanc R.

    2006-11-01

    Full Text Available Faisant le point sur l'ensemble de leurs résultats obtenus au cours des dernières années, les auteurs développent divers aspects relatifs aux synthèses, à la physico-chimie et aux structures des complexes dérivés des cobalt carbonyle. L'étude concerne essentiellement : - les dérivés de simple substitution de l'octacarbonyle dicobalt et la tautomérie des complexes dinucléaires; - les dérivés mononucléaires ioniques et leur relation avec les formes alkyle et acétyle du cobalt (I; - le bis (tétracarbonyle cobalt mercure et ses dérivés de substitution ; - les dérivés tétranucléaires et le phénomène de « migration intramoléculaire » des ligands. Les caractéristiques spectrographiques de quelque soixante-dix complexes sont fournies en annexe. The authors review their findings concerning the synthesis, physico-chemical properties and structural nature of cobalt carbonyl derivatives. The article deals with : - Normal substitution of Col (CO,, and tautomerism of binuclear complexes; - lonic mononuclear derivatives in relation with alkyl and acetylcobaltcarbonyls ; - Bis (tetracarbonylcobalt mercury and its substituted derivatives ; - Tetranuclear cobalt complexes exhibiting intramolecular scrambling. Spectrographic data of some 70 compounds are given.

  2. Photo-promoted carbonylation of chloroalkanes with carbon monoxide by non-precious metal catalysts

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The photo-promoted carbonylation of chloroalkanes with carbon monoxide was carried out under ambient conditions with copper and cadmium salts catalysts. The results indicated that the corresponding esters were produced with three salt catalysts, i.e.CuBr2, CuCl2 and CdI2. Among these catalysts, CdI2 was the most efficient in terms of ester yield and selectivity, particularly, 60% yield and 75% selectivity in the carbonylation of chlorocyclohexane were achieved. Furthermore, the yield and selectivity of the ester can be improved greatly by adding tri-n-butylamine in the CuBr2 and CuCl2 catalyst systems. On the other hand, the additive. As a result, we suggest that iodide ion plays an important role in the catalyst system of the cadmium salts.(C) 2007 Ying Ping Jia. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.

  3. Rheological properties of magnetorheological fluid prepared by gelatin-carbonyl iron composite particles

    Institute of Scientific and Technical Information of China (English)

    PAN Hua-jin; HUANG Hong-jun; ZHANG Ling-zhen; QI Jian-ying; CAO Shao-kun

    2005-01-01

    Gelatin-carbonyl iron composite particle was prepared by micro emulsion method. The analysis of scanning electron microscope(SEM) shows that the ultrafine particles are spheroids coated by gelatin, and the average sizes of particles are 3-10 μm. The specific saturation magnetization σs is 130.9 A·m2/kg, coercivity Hc is 0.823 A/m, and residual magnetism r is 4.98 Am2/kg for the composite particles. It is shown that the particles possess properties of soft magnetic. The yield stress of magnetorheological fluid(MRF) with composite particle reaches 70 kPa at 0.5 T magnetic induction. Magnetorheological effects are superior in lower magnetic field intensity and the subsidence stability of the MRF is excellent compared with pure carbonyl iron powder.

  4. Impact of lipid content and composition on lipid oxidation and protein carbonylation in experimental fermented sausages.

    Science.gov (United States)

    Fuentes, Verónica; Estévez, Mario; Ventanas, Jesús; Ventanas, Sonia

    2014-03-15

    This study aims to investigate the effect of lipid content (∼4%, ∼10% and ∼15%) and composition (different lipid sources; animal fat and sunflower oil) on the oxidative stability of proteins and lipids in experimental fermented sausages. Increasing the lipid content of sausages enhanced the susceptibility of lipids to oxidation whereas the effect on the formation of specific carbonyls from protein oxidation was not so evident. Sausages manufactured with different lipid sources affected the susceptibility of lipids and proteins to oxidation as a likely result of the modifications in the fatty acid profile, as well as to the presence of antioxidant compounds. While the fatty acid profile had a major effect on the occurrence and extent of lipid oxidation, the presence of compounds with potential antioxidant activity may be more influential on the extent of protein carbonylation.

  5. Amino acid decarboxylations produced by lipid-derived reactive carbonyls in amino acid mixtures.

    Science.gov (United States)

    Hidalgo, Francisco J; León, M Mercedes; Zamora, Rosario

    2016-10-15

    The formation of 2-phenylethylamine and phenylacetaldehyde in mixtures of phenylalanine, a lipid oxidation product, and a second amino acid was studied to determine the role of the second amino acid in the degradation of phenylalanine produced by lipid-derived reactive carbonyls. The presence of the second amino acid usually increased the formation of the amine and reduced the formation of the Strecker aldehyde. The reasons for this behaviour seem to be related to the α-amino group and the other functional groups (mainly amino or similar groups) present in the side-chain of the amino acid. These groups are suggested to modify the lipid-derived reactive carbonyl but not the reaction mechanism because the Ea of formation of both 2-phenylethylamine and phenylacetaldehyde remained unchanged in all studied systems. All these results suggest that the amine/aldehyde ratio obtained by amino acid degradation can be modified by adding free amino acids during food formulation. PMID:27173560

  6. Influence of gamma radiation reaction on the hydroesterification of butenes catalyzed by metal carbonyls

    International Nuclear Information System (INIS)

    In the hydro carboxylation reaction, which first has been studied by Reppe, olefine and acetylene compounds are processed with carbon monoxide and water at high pressures and high temperatures in the presence of metal carbonyls. This reaction can be enhanced considerably by application of ionizing radiation. Lower pressures and in particular lower temperatures can be used if gamma irradiation is performed during carboxylation. For the experiments a mixture of buten-1 and buten-2 as well as pure buten-1 and pure buten-2 has been used to study the behaviour of these olefines with respect to the isomerization of the reaction products and to the olefines not transformed in the reaction process. Replacing water, methanol has been used as a reaction component, thus obtaining directly the respective carbonyl acid esters, which can be analysed quantitatively and qualitatively with respect to their isomeric composition by gaschromatography. (orig./HK)

  7. Design and fabrication of microfluidic mixer from carbonyl iron–PDMS composite membrane

    KAUST Repository

    Li, Jiaxing

    2010-10-12

    This paper introduces a carbonyl iron-PDMS (CI-PDMS) composite magnetic elastomer in which carbonyl iron (CI) particles are uniformly distributed in a PDMS matrix. The CI particles and the PDMS were mixed at different weight ratios and tested to determine the influence of CI concentration. The magnetic and mechanical properties of the magnetic elastomers were characterized, respectively, by vibrating-sample magnetometer and by tensile testing using a mechanical analyzer. The elastomer was found to exhibit high magnetization and good mechanical flexibility. The morphology and deformation of the CI-PDMS membrane also were observed. A magnetically actuated microfluidic mixer (that is, a micromixer) integrated with CI-PDMS elastomer membranes was successfully designed and fabricated. The high efficiency and quality of the mixing makes possible the impressive potential applications of this unique CI-PDMS material in microfluidic systems. © Springer-Verlag 2010.

  8. Alkali metal and ammonium chlorides in water and heavy water (binary systems)

    CERN Document Server

    Cohen-Adad, R

    1991-01-01

    This volume surveys the data available in the literature for solid-fluid solubility equilibria plus selected solid-liquid-vapour equilibria, for binary systems containing alkali and ammonium chlorides in water or heavy water. Solubilities covered are lithium chloride, sodium chloride, potassium chloride, rubidium chloride, caesium chloride and ammonium chloride in water and heavy water.

  9. The Pharmacological Activities of the Metabolites of N-[(Trimethylamineboryl)-Carbonyl]-L-Phenylalanine Methyl Ester

    OpenAIRE

    Miller, M. C.III; Sood, A.; Spielvogel, B. F.; Shrewsbury, R. P.; Hall, I. H.

    1996-01-01

    The metabolites of N-[(trimethylamineboryl)-carbonyl]-L-phenylalanine methyl ester 1 proved to be active in a number of pharmacological screens where the parent had previously demonstrated potent activity. The proposed metabolites demonstrated significant activity as cytotoxic, hypolipidemic, and anti-inflammatory agents. In cytotoxicity screens several of the proposed metabolites afforded better activity than the parent compound against the growth of suspended and solid tumor cell lines. Eva...

  10. Influence of carbonyl stress on rheological alterations of blood materials and decarbonylation effect of glutathione

    Institute of Scientific and Technical Information of China (English)

    彭密军; 蔡建光; 贺洪; 龚萍; 李国林; 汤婷; 朱泽瑞; 印大中

    2008-01-01

    The effects of various toxic carbonyls such as malondialdehyde(MDA),a secondary product of lipid peroxidation,and other aldehydes on rheological parameters and their relationship with aging-associated alterations were studied.Both MDA and glutaraldehyde(Glu) in different concentrations significantly increase viscosity,plastic viscosity and yield stress of human plasma and erythrocyte suspensions.MDA(20 mmol/L) reduces sharply the typical fluorescence of proteins(excitation 280 nm/emission 350 nm),and produces age pigment-like fluorescence with a strong emission peak at 460 nm when excites at 395 nm by only being incubated for some hours.In contrast,Glu decreases merely the fluorescence of proteins without producing age pigment-like fluorescence.These data suggest interestingly that the MDA-induced gradual protein cross linking seems to form from different mechanisms compared to the fast rheological changes of blood materials which may take place either in acute and chronic diseases or during aging.On the other hand,MDA induces various deleterious alterations of erythrocytes whereas glutathione(GSH) inhibits the MDA-related carbonyl stress in a concentration-dependent manner.The results indicate that carbonyl-amino reaction exists in the blood widely and GSH has the ability to interrupt or reverse this reaction in a certain way.It implies that carbonyl stress may be one of the important factors in blood stasis and suggests a theoretical and practical approach in anti-stresses and anti-aging.

  11. Kinetic studies on vapor phase carbonylation of methanol to acetic acid over Rh/Ys catalyst

    Institute of Scientific and Technical Information of China (English)

    柳忠阳; 潘平来; 朱长城; 袁国卿

    1997-01-01

    A novel catalyst Rh/Ys for the carbonylation of methanol to acetic acid with CH3I as the promoter shows excellent activity and selectivity.The reaction is kinetically controlled.The reaction rate is in proportion to the concentration of Rh and CH3I but has nothing to do with those of CH3OHH and CO.The surface active energy is Ea ~51.02 kJ/mol.A mechanism is also proposed.

  12. Determination of protein carbonyls in plasma, cell extracts, tissue homogenates, isolated proteins

    DEFF Research Database (Denmark)

    Weber, Daniela; Davies, Michael J.; Grune, Tilman

    2015-01-01

    in the most relevant methods to detect protein carbonyls after derivatization with 2,4-dinitrophenylhydrazine with an emphasis on measurement in plasma, cells, organ homogenates, isolated proteins and organelles. Sample preparation, derivatization conditions and protein handling are presented...... different reactive oxygen species in blood, tissues and cells. Sample preparation and stabilization are key steps in the accurate quantification of oxidation-related products and examination of physiological/pathological processes. This review therefore focuses on the sample preparation processes used...

  13. Synthesis and Insecticidal Activity of Novel N-Pyridylpyrazole Carbonyl Thioureas

    Institute of Scientific and Technical Information of China (English)

    王宝雷; 马翼; 熊丽霞; 李正名

    2012-01-01

    A series of novel N-pyridylpyrazole carbonyl thioureas were designed and synthesized. Their structures were characterized by melting points, 1H NMR, IR and elemental analysis or HRMS. The bioassay tests indicated that some of these compounds exhibited moderate insecticidal activity against Mythirnna separata Walker and Culex pipiens pallens. Among 17 compounds, 5n and 5p showed 100% larvicidal activity against Mythimna separata Walker at the test concentration of 100 mg/L.

  14. Ionization of oriented carbonyl-sulfide molecules by intense circularly polarized laser pulses

    CERN Document Server

    Dimitrovski, Darko; Madsen, Lars Bojer; Filsinger, Frank; Meijer, Gerard; Küpper, Jochen; Holmegaard, Lotte; Kalhøj, Line; Nielsen, Jens H; Stapelfeldt, Henrik

    2010-01-01

    We present combined experimental and theoretical results on strong-field ionization of oriented carbonyl-sulphide molecules by circularly-polarized laser pulses. The obtained molecular frame photoelectron angular distributions show pronounced asymmetries perpendicular to the direction of the molecular electric dipole moment. These findings are explained by a tunneling model invoking the laser-induced Stark shifts associated with the dipoles and polarizabilities of the molecule and its unrelaxed cation.

  15. Proteomic identification of carbonylated proteins in the kidney of trichloroethene-exposed MRL+/+ mice

    OpenAIRE

    Fan, Xiuzhen; WANG, GANGDUO; English, Robert D.; Khan, M. Firoze

    2013-01-01

    Trichloroethene (TCE), a common environmental and occupational pollutant, is associated with multi-organ toxicity. Kidney is one of major target organs affected as a result of TCE exposure. Our previous studies have shown that exposure to TCE causes increased protein oxidation (protein carbonylation) in the kidneys of autoimmune-prone MRL +/+ mice, and suggested a potential role of protein oxidation in TCE-mediated nephrotoxicity. To assess the impact of chronic TCE exposure on protein oxidat...

  16. Carbonyl sulfide exchange in soils for better estimates of ecosystem carbon uptake

    OpenAIRE

    Whelan, Mary E.; Hilton, Timothy W.; Berry, Joseph A; Berkelhammer, Max; Desai, Ankur R; Campbell, J. Elliott

    2016-01-01

    Carbonyl sulfide (COS) measurements are one of the emerging tools to better quantify gross primary production (GPP), the largest flux in the global carbon cycle. COS is a gas with a similar structure to CO2; COS uptake is thought to be a proxy for GPP. However, soils are a potential source or sink of COS. This study presents a framework for understanding soil–COS interactions. Excluding wetlands, most of the few observations of isolated soils that have been made show smal...

  17. Exchange of carbonyl sulfide (COS) between the atmosphere and various soils in China

    OpenAIRE

    Liu, J; C. Geng; Mu, Y; Zhang, Y.; Z. Xu; Wu, H

    2010-01-01

    Using a dynamic enclosure, the exchange rates of carbonyl sulfide (COS) between the atmosphere and 18 soils from 12 provinces in China were investigated. The emission or uptake of COS from the soils was highly dependent on the soil type, soil temperature, soil moisture, and atmospheric COS mixing ratio. In general, with the only exception being paddy soils, the soils in this investigation acted as sinks for atmospheric COS under wide ranges of soil temperature and soil moisture. Two intensive...

  18. Carbonyl sulfide exchange in soils for better estimates of ecosystem carbon uptake

    OpenAIRE

    M. E. Whelan; T. W. Hilton; J. A. Berry; M. Berkelhammer; A. R. Desai; Campbell, J. E.

    2015-01-01

    Carbonyl sulfide (COS) measurements are one of the emerging tools to better quantify gross primary production (GPP), the largest flux in the global carbon cycle. COS is a gas with a similar structure to CO2; COS uptake is thought to be a proxy for GPP. However, soils are a potential source or sink of COS. This study presents a framework for understanding soil-COS interactions. Excluding wetlands, most of the few observations of isolated soils that have been ...

  19. Exchange of carbonyl sulfide (COS) between the atmosphere and various soils in China

    OpenAIRE

    Liu, J; C. Geng; Mu, Y; Zhang, Y.; Wu, H

    2009-01-01

    Using a dynamic enclosure, the exchange fluxes of carbonyl sulfide (COS) between the atmosphere and 18 soils from 10 provinces in China were investigated. The emission or uptake of COS from the soils was highly dependent on the soil type, soil temperature, soil moisture, and atmospheric COS mixing ratio. In general, with the only exception being paddy soils, the soils in this investigation acted as sinks for atmospheric COS under wide ranges of soil temperature and soil moisture. Two i...

  20. A carnosine intervention study in overweight human volunteers: bioavailability and reactive carbonyl species sequestering effect

    OpenAIRE

    Luca Regazzoni; Barbora de Courten; Davide Garzon; Alessandra Altomare; Cristina Marinello; Michaela Jakubova; Silvia Vallova; Patrik Krumpolec; Marina Carini; Jozef Ukropec; Barbara Ukropcova; Giancarlo Aldini

    2016-01-01

    Carnosine is a natural dipeptide able to react with reactive carbonyl species, which have been recently associated with the onset and progression of several human diseases. Herein, we report an intervention study in overweight individuals. Carnosine (2 g/day) was orally administered for twelve weeks in order to evaluate its bioavailability and metabolic fate. Two carnosine adducts were detected in the urine samples of all subjects. Such adducts are generated from a reaction with acrolein, whi...

  1. Microfluidic lab-on-a-chip derivatization for gaseous carbonyl analysis.

    Science.gov (United States)

    Pang, Xiaobing; Lewis, Alastair C; Ródenas-García, Milagros

    2013-06-28

    We present a microfluidic lab-on-a-chip derivatization technique for the analysis of gaseous carbonyl compounds using O-(2,3,4,5,6-pentafluorobenzyl) hydroxylamine (PFBHA) as the derivatizing reagent. The novel microfluidic lab-on-a-chip derivatization technique has been developed to measure nmol per mole (ppbv) mixing ratios of gaseous carbonyl compounds, which are of particular importance to atmospheric chemistry. The technique utilised a planar glass microreactor comprising three inlets and one outlet, gas and fluid splitting and combining channels, mixing junctions, and a 2.0m long, 620μm internal diameter reaction microchannel. The microreactor integrated three functions, providing: (1) a gas and liquid mixer and reactor, (2) reagent heating, and (3) sample pre-concentration. The concentration of derivatization solution, the volumetric flow rates of the incoming gas sample and PFBHA solution, and the temperature of the microreactor were optimised to achieve a near real-time measurement. The enhanced phase contact area-to-volume ratio and the high heat transfer rate in the microreactor resulted in a fast and high efficiency derivatization reaction, generating an effluent stream which was ready for direct introduction to GC-MS. Good linearity was observed for eight carbonyl compounds over the measurement ranges of 1-500ppbv when they were derivatized under optimal reaction conditions. The method detection limits (MDLs) were below 0.10nmolmol(-1) for most carbonyls in this study, which is below or close to their typical concentrations in clean ambient air. The performance of the technique was assessed by applying the methodology to the quantification of glyoxal (GLY) and methylglyoxal (MGLY) formed during isoprene photo-oxidation in an outdoor photoreactor chamber (EUPHORE). Good agreements between GLY and MGLY measurements were obtained comparing this new technique with Fourier Transform InfraRed (FTIR), which provides support for the potential effectiveness of

  2. Coupling Reaction of Carbonyl Compounds Mediated by Gallium Metal in Aqueous Media

    Institute of Scientific and Technical Information of China (English)

    汪志勇; 袁仕祯; 查正根; 张祖德

    2003-01-01

    A simple and effective pinacol coupling of various aromatic aldehydes mediated by gallium in good yields has been carried out. The reaction is highly effective in water in the prurience of KOH or HCl and was strongly affected by the steric environ-ment surrounding the carbonyl group. Aliphaflc aldehydes, ke-tones and aromatic ketones appear inert under the same reac-tion conditions.

  3. Influence of shape anisotropy on microwave complex permeability in carbonyl iron flakes/epoxy resin composites

    Institute of Scientific and Technical Information of China (English)

    Wen Fu-Sheng; Qiao Liang; Zhou Dong; Zuo Wen-Liang; Yi Hai-Bo; Li Fa-Shen

    2008-01-01

    To explore the mechanism of carbonyl iron flake composites for microwave complex permeability, this paper investigates the feature of the flakes. The shape anisotropy was certified by the results of the magnetization hysteresis loops and the Mossbauer spectra. Furthermore, the shape anisotropy was used to explain the origin of composite microwave performance, and the calculated results agree with the experiment. It is believed that the shape anisotropy dominates microwave complex permeability, and the natural resonance plays main role in flake.

  4. COMPARATIVE STUDY OF EFFICACY OF FERROUS SULPHATE AND CARBONYL IRON IN ANEMIA OF ANTENATAL WOMEN

    OpenAIRE

    Radhika; Souris

    2015-01-01

    Iron deficiency anemia is the most common and important public health problem all over the world in the risk group of antenatal women. Research is going on to improve the iron status of the pregnant women with different forms of iron available. In this regard, Carbonyl Iron is showing promising results in improving the red cell mass with better compliance. 120 antenatal women were recruited in this study. The study comprised of 6weeks fo...

  5. Density functional theory study of electroreductive hydrocoupling of alpha,beta-unsaturated carbonyl compounds.

    Science.gov (United States)

    Kise, Naoki

    2006-11-24

    [reaction: see text] The electroreductive hydrocoupling of methyl cinnamate, methyl crotonate, cumarin, and benzalacetone was studied by DFT (B3LYP/6-311++ G**) calculations. The computational outcomes for the transition states in the hydrocoupling of anion radicals generated by a one-electron transfer to the alpha,beta-unsaturated carbonyl compounds well agree with the diastereoselectivities in the experimental results previously reported. PMID:17109548

  6. DETERMINATION OF PROTEIN CARBONYL LEVELS IN PATIENTS WITH CHRONIC ALCOHOLICS AND EVALUATION TOGETHER WITH OTHER PARAMETERS

    OpenAIRE

    YALCIN, Serap

    2011-01-01

    Investigation of the impact of oxidative stress, of which chronic alcohol consumption is an important indicator, on proteins and lipids. In this study, in order to evaluate oxidative damage, blood samples of 40 alcoholic patients, lying in the psychiatry clinic of Ankara University with the diagnosis of alcoholism, and 20 healthy people have been worked with spectrophotometric method. Malondialdehyde (MDA), lipid peroxidation product, and protein carbonyl (PCO) levels observed as statisticall...

  7. Copper-incorporated mono- and di-TeRu5 metal carbonyl complexes: syntheses, structures, and an unusual skeletal arrangement.

    Science.gov (United States)

    Shieh, Minghuey; Miu, Chia-Yeh; Hsing, Kai-Jieah; Jang, Li-Fing; Lin, Chien-Nan

    2015-04-14

    Two sandwich-type Cu3Cl- or Cu2{Te2Ru4(CO)10}-bridging di-TeRu5 clusters, [{TeRu5(CO)14}2Cu3Cl](2-) () and [{TeRu5(CO)14}2Cu2{Te2Ru4(CO)10}](4-) (), were obtained from the reaction of [TeRu5(CO)14](2-) with 1 equiv. of [Cu(MeCN)4][BF4] in CH2Cl2 or THF at 0 °C, respectively, depending on the solvents. The chloride-abstracted was structurally characterized to have two TeRu5 cores that were linked by a Cu3Cl moiety with two Cu-Cu bonds. If the reaction was carried out in a molar ratio of 1 : 2 at 0 or 30 °C in CH2Cl2, the structural isomers [TeRu5(μ-CO)2(CO)12(CuMeCN)2] () and [TeRu5(μ-CO)3(CO)11Cu2(MeCN)2] () were produced, respectively, as the major product. Cluster displayed a TeRu5 core with two adjacent Ru3 triangles each capped by a μ3-Cu(MeCN) fragment, while contained a TeRu5 core with one triangle Ru3 plane capped by a Cu2(MeCN)2 fragment with two Cu atoms covalently bonded. Upon heating, the isomerization of into proceeded to undergo an unusual skeletal arrangement of Cu(MeCN) and migration of CO, with the TeRu5 core remaining intact. An electrochemical study revealed that and each exhibited only one oxidation while cluster had two consecutive oxidations, suggesting significant electronic communication between the two TeRu5 metal cores in via the Cu3 moiety. This work describes the facile synthesis of a series of semiconducting Cux-bridging Te-Ru carbonyl clusters, in which the incorporation of the Cux fragments has significantly influenced their resulting structures, rearrangements, and electronic properties, which was further elucidated by DFT calculations. PMID:25757103

  8. Mono- and Dinuclear Manganese Carbonyls Supported by 1,8-Disubstituted (L = Py, SMe, SH) Anthracene Ligand Scaffolds.

    Science.gov (United States)

    Manes, Taylor A; Rose, Michael J

    2016-06-01

    Presented herein is a synthetic scheme to generate symmetric and asymmetric ligands based on a 1,8-disubstituted anthracene scaffold. The metal-binding scaffolds were prepared by aryl chloride activation of 1,8-dichloroanthracene using Suzuki-type couplings facilitated by [Pd(dba)2] as a Pd source; the choice of cocatalyst (XPhos or SPhos) yielded symmetrically or asymmetrically substituted scaffolds (respectively): namely, Anth-SMe2 (3), Anth-N2 (4), and Anth-NSMe (6). The ligands exhibit a nonplanar geometry in the solid state (X-ray), owing to steric hindrance between the anthracene scaffold and the coupled aryl units. To determine the flexibility and binding characteristics of the anthracene-based ligands, the symmetric scaffolds were complexed with [Mn(CO)5Br] to afford the mononuclear species [(Anth-SMe2)Mn(CO)3Br] (8) and [(Anth-N2)Mn(CO)3Br] (9), in which the donor moieties chelate the Mn center in a cis fashion. The asymmetric ligand Anth-NSMe (6) binds preferentially through the py moieties, affording the bis-ligated complex [(Anth-NSMe)2Mn(CO)3Br] (10), wherein the thioether-S donors remain unbound. Alternatively, deprotection of the thioether in 6 affords the free thiol ligand Anth-NSH (7), which more readily binds the Mn center. Complexation of 7 ultimately affords the mixed-valence Mn(I)/Mn(II) dimer of formula [(Anth-NS)3Mn2(CO)3] (11), which exhibits a fac-{Mn(CO)3} unit supported by a triad of bridging thiolates, which are in turn ligated to a supporting Mn(II) center (EPR: |D| = 0.053 cm(-1), E/|D| = 0.3, Aiso = -150 MHz). All of the metal complexes have been characterized by single-crystal X-ray diffraction, IR spectroscopy and NMR/EPR measurements-all of which demonstrate that the meta-linked, anthracene-based ligand scaffold is a viable approach for the coordination of metal carbonyls. PMID:27195661

  9. Method for preparation of melts of alkali metal chlorides with highly volatile polyvalent metal chlorides

    International Nuclear Information System (INIS)

    A method for production of alkali metal (Cs, Rb, K) chloride melts with highly volatile polyvalent metal chlorides is suggested. The method consists, in saturation of alkali metal chlorides, preheated to the melting point, by volatile component vapours (titanium tetrachloride, molybdenum or tantalum pentachloride) in proportion, corresponding to the composition reguired. The saturation is realized in an evacuated vessel with two heating areas for 1-1.5 h. After gradual levelling of temperature in both areas the product is rapidly cooled. 1 fig.; 1 tab

  10. Mitochondrial ascorbate-glutathione cycle and proteomic analysis of carbonylated proteins during tomato (Solanum lycopersicum) fruit ripening.

    Science.gov (United States)

    López-Vidal, O; Camejo, D; Rivera-Cabrera, F; Konigsberg, M; Villa-Hernández, J M; Mendoza-Espinoza, J A; Pérez-Flores, L J; Sevilla, F; Jiménez, A; Díaz de León-Sánchez, F

    2016-03-01

    In non-photosynthetic tissues, mitochondria are the main source of energy and of reactive oxygen species. Accumulation of high levels of these species in the cell causes damage to macromolecules including several proteins and induces changes in different metabolic processes. Fruit ripening has been characterized as an oxidative phenomenon; therefore, control of reactive oxygen species levels by mitochondrial antioxidants plays a crucial role on this process. In this work, ascorbate-glutathione cycle components, hydrogen peroxide levels and the proteomic profile of carbonylated proteins were analyzed in mitochondria isolated from tomato (Solanum lycopersicum) fruit at two ripening stages. A significant increase on most ascorbate-glutathione cycle components and on carbonylated proteins was observed in mitochondria from breaker to light red stage. Enzymes and proteins involved in diverse cellular and mitochondrial metabolic pathways were identified among the carbonylated proteins. These results suggest that protein carbonylation is a post-translational modification involved in tomato fruit ripening regulation.

  11. Hydrogen bond and protonation during interaction of transition metal carbonyl complexes with HCl and perfluoro-tert-butanol

    International Nuclear Information System (INIS)

    Using the method of IR-spectrometry HCl interaction with some carbonyl complexes of transition metals: (Et5C5)Re(CO)3, (η6 - Me3C6H3)M(CO)3, where M = Cr, Mo, W at low temperatures in solution of liquid xenon, as well as interaction of certain complexes of Arene M (CO)L2 type with perfluoro-tert-butanol, have been investigated. It is ascertained that HCl is able to form H-bond with carbonyl Π-complexes by transition metals via oxygen atom of carbonyl group at metal atom in xenon solution. The protonation of carbonyl complexes of transition metals to metal atom can proceed via the stage of hydrogen bond formation to oxygen atom of CO group

  12. Mitochondrial ascorbate-glutathione cycle and proteomic analysis of carbonylated proteins during tomato (Solanum lycopersicum) fruit ripening.

    Science.gov (United States)

    López-Vidal, O; Camejo, D; Rivera-Cabrera, F; Konigsberg, M; Villa-Hernández, J M; Mendoza-Espinoza, J A; Pérez-Flores, L J; Sevilla, F; Jiménez, A; Díaz de León-Sánchez, F

    2016-03-01

    In non-photosynthetic tissues, mitochondria are the main source of energy and of reactive oxygen species. Accumulation of high levels of these species in the cell causes damage to macromolecules including several proteins and induces changes in different metabolic processes. Fruit ripening has been characterized as an oxidative phenomenon; therefore, control of reactive oxygen species levels by mitochondrial antioxidants plays a crucial role on this process. In this work, ascorbate-glutathione cycle components, hydrogen peroxide levels and the proteomic profile of carbonylated proteins were analyzed in mitochondria isolated from tomato (Solanum lycopersicum) fruit at two ripening stages. A significant increase on most ascorbate-glutathione cycle components and on carbonylated proteins was observed in mitochondria from breaker to light red stage. Enzymes and proteins involved in diverse cellular and mitochondrial metabolic pathways were identified among the carbonylated proteins. These results suggest that protein carbonylation is a post-translational modification involved in tomato fruit ripening regulation. PMID:26471654

  13. Purification and characterization of a novel carbonyl reductase with high stereo-selectivity

    Institute of Scientific and Technical Information of China (English)

    YANG Ming; XU Yan; MU Xiaoqing; XIAO Rong

    2007-01-01

    A novel NADPH-dependent carbonyl reductase was separated from Candida parapsilosis CCTCC 203011.The enzyme gave a single band on sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE),which was purified through ammonium sulfate,Diethylamino Ethanol (DEAE) sepharose Fast flow (FF),phenyl-sepharose FF and blue sepharose FF chromatography from cell-free extract.The molecular mass of the enzyme was about 30 kDa.The optimum pH and temperature for reduction were 4.5℃ and 35℃,respectively.The Cu2+ had strong restrictive effect on enzyme activity.In addition,the carbonyl reductase was an enzyme with high substrate specificity and stereo-selectivity,and showed high asymmetric reduction activity towards α-hydroxyacetophenone and ethyl 4-chloro acetoacetate.For the asymmetric reduction of α-hydroxyacetophenone and ethyl 4-chloro acetoacetate,(S)-1-phenyl-1,2-ethanediol and (R)-ethyl 4-chloro-3-hydroxybutanoate were produced by the purified enzyme,with the 100% and 94.3% e.e.value,respectively.Therefore,the enzyme could be one of the effective biocatalysts for asymmetric synthesis of chiral alcohols.The amino acid sequences of one peptide from the purified enzyme were analyzed by LC-MASS-MASS,and the carbonyl reductase showed some identity to the hypothetical protein CaO 19.10414 reported.

  14. Blot-MS of Carbonylated Proteins: A Tool to Identify Oxidized Proteins.

    Science.gov (United States)

    Ferreira, Rita; Domingues, Pedro; Amado, Francisco; Vitorino, Rui

    2016-01-01

    The efficiency of proteostasis regulation declines during aging and the failure of protein homeostasis is common in age-related diseases. Protein oxidation is a major contributor to the loss of proteome homeostasis, also called "proteostasis," precluding protein misfolding and aggregation. So, the identification of the molecular pathways impaired by protein oxidation will increase the understanding of proteostasis and the pathophysiological conditions related to the loss of proteostasis. Sample derivatization with dinitrophenyl hydrazine and western blot immunoassay detection of carbonylated proteins (commonly known as Oxyblot™) coupled to mass spectrometry (blot-MS) is an attractive methodological approach to identify proteins that are more prone to carbonylation, a typical oxidative modification of amino acid residues. The integration of blot-MS data of carbonylated proteins with bioinformatics tools allows the identification of the biological processes more affected by protein oxidation and that, eventually, result in the loss of proteostasis.In this chapter, we describe a blot-MS methodology to identify the proteins more prone to oxidation in biological samples, as cell and tissue extracts, and biofluids. Analysis of mitochondria isolated from cardiac tissue is provided as an example. Bioinformatic strategy to deal with data retrieved from blot-MS experiments are proposed for the identification of relevant biological processes modulated by oxidative stress stimuli. PMID:27613049

  15. Effect of carbonyl inhibitors and their H₂O₂ detoxification on lactic acid fermentation.

    Science.gov (United States)

    Li, Jing; Zhu, Caiqing; Tu, Maobing; Han, Pingping; Wu, Yonnie

    2015-04-01

    Biomass degradation compounds significantly inhibit biochemical conversion of biomass prehydrolysates to biofuels and chemicals, such as lactic acid. To characterize the structure-activity relationship of carbonyl inhibition on lactic acid fermentation, we examined effects of eight carbonyl compounds (furfural, 5-hydroxymethyl furfural, vanillin, syringaldehyde, 4-hydroxybenzaldehyde, phthalaldehyde, benzoic acid, and pyrogallol aldehyde) and creosol on lactic acid production by Lactobacillus delbrueckii. Pyrogallol aldehyde reduced the cell growth rate by 35 % at 1.0 mM and inhibited lactic acid production completely at 2.0 mM. By correlating the molecular descriptors to the inhibition constants in lactic acid fermentation, we found a good relationship between the hydrophobicity (Log P) of aldehydes and their inhibition constants in fermentation. The inhibitory effect of carbonyl inhibitors appeared to correlate with their thiol reactivity as well. In addition, we found that H2O2 detoxified pyrogallol aldehyde and phthalaldehyde inhibitory activity. H2O2 detoxification was applied to real biomass prehydrolysates in lactic acid fermentation. PMID:25666370

  16. Nitrite promotes protein carbonylation and Strecker aldehyde formation in experimental fermented sausages: are both events connected?

    Science.gov (United States)

    Villaverde, A; Ventanas, J; Estévez, M

    2014-12-01

    The role played by curing agents (nitrite, ascorbate) on protein oxidation and Strecker aldehyde formation is studied. To fulfill this objective, increasing concentrations of nitrite (0, 75 and 150ppm) and ascorbate (0, 250 and 500ppm) were added to sausages subjected to a 54day drying process. The concurrence of intense proteolysis, protein carbonylation and formation of Strecker aldehydes during processing of sausages suggests that α-aminoadipic semialdehyde (AAS) and γ-glutamic semialdehyde (GGS) may be implicated in the formation of Strecker aldehydes. The fact that nitrite (150ppm, ingoing amount) significantly promoted the formation of protein carbonyls at early stages of processing and the subsequent formation of Strecker aldehydes provides strength to this hypothesis. Ascorbate (125 and 250ppm) controlled the overall extent of protein carbonylation in sausages without declining the formation of Strecker aldehydes. These results may contribute to understanding the chemistry fundamentals of the positive influence of nitrite on the flavor and overall acceptability of cured muscle foods.

  17. Role of Protein Carbonylation in Skeletal Muscle Mass Loss Associated with Chronic Conditions

    Directory of Open Access Journals (Sweden)

    Esther Barreiro

    2016-05-01

    Full Text Available Muscle dysfunction, characterized by a reductive remodeling of muscle fibers, is a common systemic manifestation in highly prevalent conditions such as chronic heart failure (CHF, chronic obstructive pulmonary disease (COPD, cancer cachexia, and critically ill patients. Skeletal muscle dysfunction and impaired muscle mass may predict morbidity and mortality in patients with chronic diseases, regardless of the underlying condition. High levels of oxidants may alter function and structure of key cellular molecules such as proteins, DNA, and lipids, leading to cellular injury and death. Protein oxidation including protein carbonylation was demonstrated to modify enzyme activity and DNA binding of transcription factors, while also rendering proteins more prone to proteolytic degradation. Given the relevance of protein oxidation in the pathophysiology of many chronic conditions and their comorbidities, the current review focuses on the analysis of different studies in which the biological and clinical significance of the modifications induced by reactive carbonyls on proteins have been explored so far in skeletal muscles of patients and animal models of chronic conditions such as COPD, disuse muscle atrophy, cancer cachexia, sepsis, and physiological aging. Future research will elucidate the specific impact and sites of reactive carbonyls on muscle protein content and function in human conditions.

  18. A carnosine intervention study in overweight human volunteers: bioavailability and reactive carbonyl species sequestering effect

    Science.gov (United States)

    Regazzoni, Luca; de Courten, Barbora; Garzon, Davide; Altomare, Alessandra; Marinello, Cristina; Jakubova, Michaela; Vallova, Silvia; Krumpolec, Patrik; Carini, Marina; Ukropec, Jozef; Ukropcova, Barbara; Aldini, Giancarlo

    2016-06-01

    Carnosine is a natural dipeptide able to react with reactive carbonyl species, which have been recently associated with the onset and progression of several human diseases. Herein, we report an intervention study in overweight individuals. Carnosine (2 g/day) was orally administered for twelve weeks in order to evaluate its bioavailability and metabolic fate. Two carnosine adducts were detected in the urine samples of all subjects. Such adducts are generated from a reaction with acrolein, which is one of the most toxic and reactive compounds among reactive carbonyl species. However, neither carnosine nor adducts have been detected in plasma. Urinary excretion of adducts and carnosine showed a positive correlation although a high variability of individual response to carnosine supplementation was observed. Interestingly, treated subjects showed a significant decrease in the percentage of excreted adducts in reduced form, accompanied by a significant increase of the urinary excretion of both carnosine and carnosine-acrolein adducts. Altogether, data suggest that acrolein is entrapped in vivo by carnosine although the response to its supplementation is possibly influenced by individual diversities in terms of carnosine dietary intake, metabolism and basal production of reactive carbonyl species.

  19. Spatial distributions of and diurnal variations in low molecular weight carbonyl compounds in coastal seawater, and the controlling factors

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Kazuhiko, E-mail: takedaq@hiroshima-u.ac.jp [Graduate School of Biosphere Science, Hiroshima University, 1-7-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8521 (Japan); Katoh, Shinya; Mitsui, Yumi; Nakano, Shinichi [Graduate School of Biosphere Science, Hiroshima University, 1-7-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8521 (Japan); Nakatani, Nobutake [Graduate School of Biosphere Science, Hiroshima University, 1-7-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8521 (Japan); Department of Environmental and Symbiotic Sciences, Rakuno Gakuen University, 582 Bunkyodai-Midorimachi, Ebetsu, Hokkaido 069-8501 (Japan); Sakugawa, Hiroshi [Graduate School of Biosphere Science, Hiroshima University, 1-7-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8521 (Japan)

    2014-09-15

    We studied the spatial distributions of and the diurnal variations in four low molecular weight (LMW) carbonyl compounds, formaldehyde, acetaldehyde, propionaldehyde, and glyoxal, in coastal seawater. The samples were taken from the coastal areas of Hiroshima Bay, the Iyo Nada, and the Bungo Channel, western Japan. The formaldehyde, acetaldehyde, and glyoxal concentrations were higher in the northern part of Hiroshima Bay than at offshore sampling points in the Iyo Nada and the Bungo Channel. These three compounds were found at much higher concentrations in the surface water than in deeper water layers in Hiroshima Bay. It is noteworthy that propionaldehyde was not detected in any of the seawater samples, the concentrations present being lower than the detection limit (1 nanomole per liter (nM)) of the high performance liquid chromatography (HPLC) system we used. Photochemical and biological experiments were performed in the laboratory to help understand the characteristic distributions and fates of the LMW carbonyl compounds. The primary process controlling their fate in the coastal environment appears to be their biological consumption. The direct photo degradation of propionaldehyde, initiated by ultraviolet (UV) absorption, was observed, although formaldehyde and acetaldehyde were not degraded by UV irradiation. Our results suggest that the degradation of the LMW carbonyl compounds by photochemically formed hydroxyl radicals is relatively insignificant in the study area. Atmospheric deposition is a possible source of soluble carbonyl compounds in coastal surface seawater, but it may not influence the carbonyl concentrations in offshore waters. - Highlights: • Low molecular weight (LMW) carbonyl compounds in coastal seawater were determined. • Photochemical productions of LMW carbonyl compounds in seawater were observed. • LMW carbonyl compounds were largely consumed biologically. • Photochemical degradation was relatively insignificant in the study area.

  20. Cytoprotective Effects of Hydrophilic and Lipophilic Extracts of Pistacia vera against Oxidative Versus Carbonyl Stress in Rat Hepatocytes

    OpenAIRE

    Shahraki, Jafar; Zareh, Mona; Kamalinejad, Mohammad; Pourahmad, Jalal

    2014-01-01

    This study was conducted to evaluate the cytoprotection of various extracts and bioactive compounds found in Pistacia vera againts cytotoxicity, ROS formation, lipid peroxidation, protein carbonylation, mitochondrial and lysosomal membrane damages in cell toxicity models of diabetes related carbonyl (glyoxal) and oxidative stress (hydroperoxide). Methanol, water and ethyl acetate were used to prepare crude pistachios extracts, which were then used to screen for in-vitro cytoprotection of fres...

  1. Liquid crystalline critical dynamics in decylammonium chloride

    CERN Document Server

    Lee, K W; Lee, C E; Kang, K H; Rhee, C; Kang, J K

    1999-01-01

    Collective chain dynamics and phase transitions in a model biomembrane, decylammonium chloride (C sub 1 sub 0 H sub 2 sub 1 NH sub 3 Cl), were studied by means of proton nuclear magnetic resonance. Our measurements sensitively reflect the critical dynamics associated with the smectic C to smectic A transition of the lipid bilayer.

  2. 75 FR 20625 - Barium Chloride From China

    Science.gov (United States)

    2010-04-20

    ... established a schedule for the conduct of this review (74 FR 62587, November 30, 2010). Subsequently, counsel... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION:...

  3. Chloride migration in concrete with superabsorbent polymers

    DEFF Research Database (Denmark)

    Hasholt, Marianne Tange; Jensen, Ole Mejlhede

    2015-01-01

    Superabsorbent polymers (SAP) can be used as a means for internal curing of concrete. In the present study, the development of transport properties of concrete with SAP is investigated. The chloride migration coefficient according to NT BUILD 492 is used as a measure of this. Twenty concrete...

  4. Determination of chloride in uranium solutions

    Energy Technology Data Exchange (ETDEWEB)

    Danse, A.; Stoch, H.; Steele, T.W.

    1967-05-15

    Thiocyanate is first removed by precipitation with a small excess of a copper solution, and the cations are removed by passing the filtrate through a cation-exchange resin. The chloride is determined in the eluate by a potentiometric titration in which silver nitrate solution is used.

  5. Amperometric Sensor for Detection of Chloride Ions

    Directory of Open Access Journals (Sweden)

    Rene Kizek

    2008-09-01

    Full Text Available Chloride ion sensing is important in many fields such as clinical diagnosis, environmental monitoring and industrial applications. We have measured chloride ions at a carbon paste electrode (CPE and at a CPE modified with solid AgNO3, a solution of AgNO3 and/or solid silver particles. Detection limits (3 S/N for chloride ions were 100 μM, 100 μM and 10 μM for solid AgNO3, solution of AgNO3 and/or solid silver particles, respectively. The CPE modified with silver particles is the most sensitive to the presence chloride ions. After that we approached to the miniaturization of the whole electrochemical instrument. Measurements were carried out on miniaturized instrument consisting of a potentiostat with dimensions 35 × 166 × 125 mm, screen printed electrodes, a peristaltic pump and a PC with control software. Under the most suitable experimental conditions (Britton-Robinson buffer, pH 1.8 and working electrode potential 550 mV we estimated the limit of detection (3 S/N as 500 nM.

  6. Gebromeerde vlamvertragers en broomdioxines in Choline Chloride

    NARCIS (Netherlands)

    Egmond, van H.J.; Traag, W.A.; Hoogenboom, L.A.P.

    2008-01-01

    Sinds begin 2008 worden in het Nationaal Plan Diervoeder Choline Chloride monsters (= diervoeder additief) gevonden waarbij de DR CALUX screenings-assay een sterk verdacht signaal geeft, maar bij de GC-HRMS geen dioxines en dl-PCB's worden gevonden. Dit rapport beschrijft de resultaten van nader ond

  7. Regulated trafficking of the CFTR chloride channel

    NARCIS (Netherlands)

    Braakman, L.J.; Kleizen, B.; Jonge, H.R. de

    2000-01-01

    The cystic fibrosis transmembrane conductance regulator (CFTR), the ABC transporter encoded by the cystic fibrosis gene, is localized in the apical membrane of epithelial cells where it functions as a cyclic AMP-regulated chloride channel and as a regulator of other ion channels and transporters. Wh

  8. 21 CFR 582.3845 - Stannous chloride.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Stannous chloride. 582.3845 Section 582.3845 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  9. Gas phase carbonyl compounds in ship emissions: Differences between diesel fuel and heavy fuel oil operation

    Science.gov (United States)

    Reda, Ahmed A.; Schnelle-Kreis, J.; Orasche, J.; Abbaszade, G.; Lintelmann, J.; Arteaga-Salas, J. M.; Stengel, B.; Rabe, R.; Harndorf, H.; Sippula, O.; Streibel, T.; Zimmermann, R.

    2014-09-01

    Gas phase emission samples of carbonyl compounds (CCs) were collected from a research ship diesel engine at Rostock University, Germany. The ship engine was operated using two different types of fuels, heavy fuel oil (HFO) and diesel fuel (DF). Sampling of CCs was performed from diluted exhaust using cartridges and impingers. Both sampling methods involved the derivatization of CCs with 2,4-Dinitrophenylhydrazine (DNPH). The CCs-hydrazone derivatives were analyzed by two analytical techniques: High Performance Liquid Chromatography-Diode Array Detector (HPLC-DAD) and Gas Chromatography-Selective Ion Monitoring-Mass Spectrometry (GC-SIM-MS). Analysis of DNPH cartridges by GC-SIM-MS method has resulted in the identification of 19 CCs in both fuel operations. These CCs include ten aliphatic aldehydes (formaldehyde, acetaldehyde, propanal, isobutanal, butanal, isopentanal, pentanal, hexanal, octanal, nonanal), three unsaturated aldehydes (acrolein, methacrolein, crotonaldehyde), three aromatic aldehyde (benzaldehyde, p-tolualdehyde, m,o-molualdehyde), two ketones (acetone, butanone) and one heterocyclic aldehyde (furfural). In general, all CCs under investigation were detected with higher emission factors in HFO than DF. The total carbonyl emission factor was determined and found to be 6050 and 2300 μg MJ-1 for the operation with HFO and DF respectively. Formaldehyde and acetaldehyde were found to be the dominant carbonyls in the gas phase of ship engine emission. Formaldehyde emissions factor varied from 3500 μg MJ-1 in HFO operation to 1540 μg MJ-1 in DF operation, which is 4-30 times higher than those of other carbonyls. Emission profile contribution of CCs showed also a different pattern between HFO and DF operation. The contribution of formaldehyde was found to be 58% of the emission profile of HFO and about 67% of the emission profile of DF. Acetaldehyde showed opposite behavior with higher contribution of 16% in HFO compared to 11% for DF. Heavier carbonyls

  10. Investigation of factors influencing chloride extraction efficiency during electrochemical chloride extraction from reinforcing concrete

    Science.gov (United States)

    Sharp, Stephen R.

    2005-11-01

    Electrochemical chloride extraction (ECE) is an accelerated bridge restoration method similar to cathodic protection, but operates at higher current densities and utilizes a temporary installation. Both techniques prolong the life of a bridge by reducing the corrosion rate of the reinforcing bar when properly applied. ECE achieves this by moving chlorides away from the reinforcement and out of the concrete while simultaneously increasing the alkalinity of the electrolyte near the reinforcing steel. Despite the proven success, significant use of ECE has not resulted in part due to an incomplete understanding in the following areas: (1) An estimation of the additional service life that can be expected following treatment when the treated member is again subjected to chlorides; (2) The cause of the decrease in current flow and, therefore, chloride removal rate during treatment; (3) Influence of water-to-cement (w/c) ratio and cover depth on the time required for treatment. This dissertation covers the research that is connected to the last two areas listed above. To begin examining these issues, plain carbon steel reinforcing bars (rebar) were embedded in portland cement concrete slabs of varying water-to-cement (w/c) ratios and cover depths, and then exposed to chlorides. A fraction of these slabs had sodium chloride added as an admixture, with all of the slabs subjected to cyclical ponding with a saturated solution of sodium chloride. ECE was then used to remove the chlorides from these slabs while making electrical measurements in the different layers between the rebar (cathode) and the titanium mat (anode) to follow the progress of the ECE process. During this study, it was revealed that the resistance of the outer concrete surface layer increases during ECE, inevitably restricting current flow, while the resistance of the underlying concrete decreases or remains constant. During ECE treatment, a white residue formed on the surface of the concrete. Analyses of the

  11. Viscosity and density tables of sodium chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Fair, J.A.; Ozbek, H. (comps.)

    1977-04-01

    A file is presented containing tabulated data extracted from the scientific literature on the density and viscosity of aqueous sodium chloride solutions. Also included is a bibliography of the properties of aqueous sodium chloride solutions. (MHR)

  12. Recherches récentes sur le cobalt carbonyle et ses dérivés Recent Studies of Cobalt Carbonyl and Its Derivatives

    OpenAIRE

    Poilblanc R.; Attali S.; Arabi M. S.; Labroue D.; Maisonnat A.; De Montaurzon D.

    2006-01-01

    Faisant le point sur l'ensemble de leurs résultats obtenus au cours des dernières années, les auteurs développent divers aspects relatifs aux synthèses, à la physico-chimie et aux structures des complexes dérivés des cobalt carbonyle. L'étude concerne essentiellement : - les dérivés de simple substitution de l'octacarbonyle dicobalt et la tautomérie des complexes dinucléaires; - les dérivés mononucléaires ioniques et leur relation avec les formes alkyle et acétyle du cobalt (I); - le bis (tét...

  13. Kinetics of Vinyl Chloride Polymerization with Mixture of Initiators

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Kinetic models for the rate constants of vinyl chloride polymerization in the presence of initiator mixtures were proposed. They may be used to design the initiator recipes for the vinyl chloride polymerization with uniform rate at different temperatures at which various grades of poly(vinyl chloride) will be prepared.

  14. Removal of iron contaminant from zirconium chloride solution

    International Nuclear Information System (INIS)

    This patent describes a process for eliminating iron contaminant from an aqueous zirconium chloride solution that has been contaminated with FeCl3 in a plant in which zirconium and hafnium chloride solutions are separated by a main MINK solvent extraction system and the FeCl3 is normally removed from the zirconium chloride solution by a secondary MINK solvent extraction system

  15. Revised Model of Chloride Diffusion in Concrete Bridge by Considering Complex Action of Load and Chloride Binding Capacity

    OpenAIRE

    Xiang, Yiqiang; Guo, DongMei

    2014-01-01

    Coastal concrete bridges will suffer from deterioration of RC structural performance and resistance attenuation because of the chloride penetration and other environment factors. This article discusses current different chloride diffusion models and puts forward the revised model of chloride diffusion in concrete bridge by considering the complex action of load influence and chloride-binding capacity. Comparison of numerical predicted values and relative experimental tests show the presented ...

  16. Carbonyl compounds in dining areas, kitchens and exhaust streams in restaurants with varying cooking methods in Kaohsiung, Taiwan.

    Science.gov (United States)

    Cheng, Jen-Hsuan; Lee, Yi-Shiun; Chen, Kang-Shin

    2016-03-01

    Eighteen carbonyl species in C1-C10 were measured in the dining areas, kitchens and exhaust streams of six different restaurant types in Kaohsiung, southern Taiwan. Measured results in the dining areas show that Japanese barbecue (45.06ppb) had the highest total carbonyl concentrations (sum of 18 compounds), followed by Chinese hotpot (38.21ppb), Chinese stir-frying (8.99ppb), Western fast-food (8.22ppb), Chinese-Western mixed style (7.38ppb), and Chinese buffet (3.08ppb), due to their different arrangements for dining and cooking spaces and different cooking methods. On average, low carbon-containing species (C1-C4), e.g., formaldehyde, acetaldehyde, acetone and butyraldehyde were dominant and contributed 55.01%-94.52% of total carbonyls in the dining areas of all restaurants. Meanwhile, Chinese-Western mixed restaurants (45.48ppb) had high total carbonyl concentrations in kitchens mainly because of its small kitchen and poor ventilation. However, high carbon-containing species (C5-C10) such as hexaldehyde, heptaldehyde and nonanaldehyde (16.62%-77.00% of total carbonyls) contributed comparatively with low carbon-containing compounds (23.01%-83.39% of total carbonyls) in kitchens. Furthermore, Chinese stir-frying (132.10ppb), Japanese barbecue (125.62ppb), Western fast-food (122.67ppb), and Chinese buffet (119.96ppb) were the four restaurant types with the highest total carbonyl concentrations in exhaust streams, indicating that stir-frying and grilling are inclined to produce polluted gases. Health risk assessments indicate that Chinese hotpot and Japanese barbecue exceeded the limits of cancer risk (10(-6)) and hazard index (=1), mainly due to high concentrations of formaldehyde. The other four restaurants were below both limits. PMID:26969068

  17. BARRIER PROPERTIES OF VINYLIDENE CHLORIDE COPOLYMERS

    Institute of Scientific and Technical Information of China (English)

    LI Yuesheng; WENG Zhixue; HUANG Zhiming; PAN Zuren

    1996-01-01

    The permeability coefficients of a series of copolymers of vinylidene chloride (VDC)with methyl acrylate (MA), butyl acrylate (BA) or vinyl chloride (VC) (as comonomer)to oxygen and carbon dioxide have been measured at 1.0 MPa and 30℃, while those to water vapor have been measured at 30℃ and 100% relative humidity. All the copolymers are semicrystalline. VDC/MA copolymers have lower melting temperature compared with VDC/BA copolymers, while that melting temperature of VDC/VC copolymer is higher than that of VDC/acrylate copolymers with the same VDC content. The barrier property of the copolymers is predominantly controlled by crystallite, free volume fraction, and cohesive energy. The permeability coefficients of VDC/MA copolymers to oxygen, carbon dioxide, and water vapor were successfully correlated with the ratio of free volume to cohesive energy.

  18. STABILISATION OF SILTY CLAY SOIL USING CHLORIDE

    Directory of Open Access Journals (Sweden)

    TAMADHER T. ABOOD

    2007-04-01

    Full Text Available The object of this paper is to investigate the effect of adding different chloride compounds including (NaCl, MgCl2, CaCl2 on the engineering properties of silty clay soil. Various amounts of salts (2%, 4%, and 8% were added to the soil to study the effect of salts on the compaction characteristics, consistency limits and compressive strength. The main findings of this study were that the increase in the percentage of each of the chloride compounds increased the maximum dry density and decrease the optimum moisture content. The liquid limit, plastic limit and plasticity index decreased with the increase in salt content. The unconfinedcompressive strength increased as the salt content increased.

  19. Chloride migration in concrete with superabsorbent polymers

    OpenAIRE

    Hasholt, Marianne Tange; Jensen, Ole Mejlhede

    2015-01-01

    Superabsorbent polymers (SAP) can be used as a means for internal curing of concrete. In the present study, the development of transport properties of concrete with SAP is investigated. The chloride migration coefficient according to NT BUILD 492 is used as a measure of this. Twenty concrete mixtures aretested 7, 14, and 28 days after casting. The development of degree of hydration is followed for 20 corresponding paste mixtures.Both when SAP is added with extra water to compensate the SAP wa...

  20. A Duplex Stainless Steel for Chloride Environments

    Science.gov (United States)

    Sridhar, N.; Kolts, J.; Flasche, L. H.

    1985-03-01

    This paper examines the effects of microstructural changes on the corrosion, stress corrosion cracking and corrosion fatigue resistance of a duplex stainless steel to chloride environments. The microstructural changes can be precipitation of phases such as sigma and carbides, or changes in the distribution of austenite and ferrite. The former can be important in hot forming operations while the latter is important in welding. The methods of minimizing these deleterious effects can sometimes be different from those used for austenitic stainless steel.

  1. Electrodeposition of Zinc from Chloride Solution

    OpenAIRE

    NAIK, Yanjerappa Arthoba; VENKATESHA, Thimmappa Venkatarangaiah

    2002-01-01

    The electroplating of zinc is carried out in the presence of 3,4,5-Trimethoxy benzaldehyde from a chloride bath. The bath constituents are optimized through Hull cell experiments. Operating parameters such as pH, temperature, and current density are also optimized. The current efficiency and throwing power are measured at different current densities. Polarization study is carried out under galvanostatic conditions. Corrosion resistance test indicated good protection of steel by the ...

  2. (tert-Butyl(2-hydroxyethylammonium chloride

    Directory of Open Access Journals (Sweden)

    Cintya Valerio-Cárdenas

    2014-07-01

    Full Text Available In the cation of the title molecular salt, C6H16NO+·Cl−, the N—C—C—O torsion angle is 176.5 (2°. In the crystal, the cations and chloride ions are linked by N—H...O and O—H...O hydrogen bonds, generating a two-dimensional network parallel to (100.

  3. Influence of chloride admixtures on cement matrix durability

    International Nuclear Information System (INIS)

    The influence of various inorganic salts, as chloride admixtures to Portland cement, on the mechanical properties and the durability of the matrix has been studied. The salts used in this study are chromium, nickel and cadmium chlorides. Improved compressive strength values are obtained which have been correlated to the stable metal hydroxide formation in high pH environment. Under static water conditions at 500C, hydrolyzed chloride ions exhibit adverse effects on the matrix durability through rapid release of calcium as calcium chloride in the initial period of leaching. On the contrary, enhanced matrix durability is obtained on long term leaching in the case of cement containing chromium chloride

  4. Boldine action against the stannous chloride effect.

    Science.gov (United States)

    Reiniger, I W; Ribeiro da Silva, C; Felzenszwalb, I; de Mattos, J C; de Oliveira, J F; da Silva Dantas, F J; Bezerra, R J; Caldeira-de-Araújo, A; Bernardo-Filho, M

    1999-12-15

    Peumus boldus extract has been used in popular medicine in the treatment of biliar litiase, hepatic insufficiency and liver congestion. Its effects are associated to the substance boldine that is present in its extract. In the present work, we evaluated the influence of boldine both in: (i) the structural conformation of a plasmid pUC 9.1 through gel electrophoresis analysis; and in (ii) the survival of the strain of Escherichia coli AB1157 submitted to reactive oxygen species (ROS), generated by a Fenton like reaction, induced by stannous chloride. Our results show a reduction of the lethal effect induced by stannous chloride on the survival of the E. coli culture in the presence of boldine. The supercoiled form of the plasmid is not modified by stannous chloride in the presence of boldine. We suggest that the protection induced by boldine could be explained by its anti-oxidant mechanism. In this way, the boldine could be reacting with stannous ions, protecting them against the oxidation and, consequently, avoiding the generation of ROS. PMID:10624900

  5. Potassium chloride production by microcline chlorination

    Energy Technology Data Exchange (ETDEWEB)

    Orosco, Pablo, E-mail: porosco@unsl.edu.ar [Instituto de Investigaciones en Tecnología Química (INTEQUI), Chacabuco y Pedernera, San Luis (Argentina); Facultad de Química, Bioquímica y Farmacia, Universidad Nacional de San Luis, Chacabuco y Pedernera, San Luis (Argentina); Ruiz, María del Carmen [Instituto de Investigaciones en Tecnología Química (INTEQUI), Chacabuco y Pedernera, San Luis (Argentina)

    2015-08-10

    Highlights: • Use of chlorination for the KCl production. • The reagents used were microcline, hydromagnesite and chlorine. • Isothermal and non-isothermal assays were performed in Cl{sub 2}–N{sub 2} mixture. • The chlorination generated KCl at 700 °C. • The chlorination products promote KCl formation. - Abstract: The potassium chloride is one of the most important fertilizers used in agriculture. The current demand of this salt makes interesting the study of potassium chloride production from unconventional potassium resources. In this work the potassium chloride production by chlorination of microcline was investigated. The starting reagents were microcline, hydromagnesite and chlorine. Non-isothermal and isothermal chlorination assays were carried out in a thermogravimetric device adapted to work in corrosive atmospheres. The temperature effect on potassium extraction and the phase transformations produced during chlorination of microcline were studied. The reagents and reaction products were analyzed by X-ray fluorescence (XRF) and X-ray diffraction (XRD). The experimental results indicated that by chlorination of microcline an important extraction of potassium in the temperature range from 800 to 900 °C was produced. Moreover, at 800 °C the forsterite, enstatite and magnesium aluminate spinel phases were generated.

  6. Understanding microwave vessel contamination by chloride species.

    Science.gov (United States)

    Recchia, Sandro; Spanu, Davide; Bianchi, Davide; Dossi, Carlo; Pozzi, Andrea; Monticelli, Damiano

    2016-10-01

    Microwaves are widely used to assist digestion, general sample treatment and synthesis. The use of aqua regia is extensively adopted for the closed vessel mineralization of samples prior to trace element detection, leading to the contamination of microwave vessels by chlorine containing species. The latter are entrapped in the polymeric matrix of the vessels, leading to memory effects that are difficult to remove, among which the risk of silver incomplete recoveries by removal of the sparingly soluble chloride is the predominant one. In the present paper, we determined by mass spectrometry that hydrogen chloride is the species entrapped in the polymeric matrix and responsible for vessel contamination. Moreover, several decontamination treatments were considered to assess their efficiency, demonstrating that several cleaning cycles with water, nitric acid or silver nitrate in nitric acid were inefficient in removing chloride contamination (contamination reduction around 90%). Better results (≈95% decrease) were achieved by a single decontamination step in alkaline environment (sodium hydroxide or ammonia). Finally, a thermal treatment in a common laboratory oven (i.e. without vacuum and ventilation) was tested: a one hour heating at 150°C leads to a 98.5% decontamination, a figure higher than the ones obtained by wet treatments which requires comparable time. The latter treatment is a major advancement with respect to existing treatments as it avoids the need of a vacuum oven for at least 17h as presently proposed in the literature.

  7. An autopsy case of zinc chloride poisoning.

    Science.gov (United States)

    Kondo, Takeshi; Takahashi, Motonori; Watanabe, Seiya; Ebina, Masatomo; Mizu, Daisuke; Ariyoshi, Koichi; Asano, Migiwa; Nagasaki, Yasushi; Ueno, Yasuhiro

    2016-07-01

    Ingestion of large amounts of zinc chloride causes corrosive gastroenteritis with vomiting, abdominal pain, and diarrhea. Some individuals experience shock after ingesting large amounts of zinc chloride, resulting in fatality. Here, we present the results of an administrative autopsy performed on a 70-year-old man who ingested zinc chloride solution and died. After drinking the solution, he developed vomiting, abdominal pain, and diarrhea, and called for an ambulance. Except for tachycardia, his vital signs were stable at presentation. However, he developed hypotension and severe metabolic acidosis and died. The patient's blood zinc concentration on arrival was high at 3030μg/dL. Liver cirrhosis with cloudy yellow ascites was observed, however, there were no clear findings of gastrointestinal perforation. The gastric mucosa was gray-brown, with sclerosis present in all gastric wall layers. Zinc staining was strongly positive in all layers. There was almost no postmortem degeneration of the gastric mucosal epithelium, and hypercontracture of the smooth muscle layer was observed. Measurement of the zinc concentration in the organs revealed the highest concentration in the gastric mucosa, followed by the pancreas and spleen. Clinically, corrosive gastroenteritis was the cause of death. However, although autopsy revealed solidification in the esophagus and gastric mucosa, there were no findings in the small or large intestine. Therefore, metabolic acidosis resulting from organ damage was the direct cause of death. PMID:27497327

  8. Formation and emissions of carbonyls during and following gas-phase ozonation of indoor materials

    Science.gov (United States)

    Poppendieck, D. G.; Hubbard, H. F.; Weschler, C. J.; Corsi, R. L.

    Ozone concentrations that are several orders of magnitude greater than typical urban ambient concentrations are necessary for gas-phase ozonation of buildings, either for deodorization or for disinfection of biological agents. However, there is currently no published literature on the interaction of building materials and ozone under such extreme conditions. It would be useful to understand, for example in the case of building re-occupation planning, what types and amounts of reaction products may form and persist in a building after ozonation. In this study, 24 materials were exposed to ozone at concentrations of 1000 ppm in the inlet stream of experimental chambers. Fifteen target carbonyls were selected and measured as building ozonation by-products (BOBPs). During the 36 h that include the 16 h ozonation and 20 h persistence phase, the total BOBP mass released from flooring and wall coverings ranged from 1 to 20 mg m -2, with most of the carbonyls being of lower molecular weight (C 1-C 4). In contrast, total BOBP mass released from wood-based products ranged from 20 to 100 mg m -2, with a greater fraction of the BOBPs being heavier carbonyls (C 5-C 9). The total BOBP mass released during an ozonation event is a function of both the total surface area of the material and the BOBP emission rate per unit area of material. Ceiling tile, carpet, office partition, and gypsum wallboard with flat latex paint often have large surface areas in commercial buildings and these same materials exhibited relatively high BOBP releases. The greatest overall BOBP mass releases were observed for three materials that building occupants might have significant contact with: paper, office partition, and medium density fiberboard, e.g., often used in office furniture. These materials also exhibited extended BOBP persistence following ozonation; some BOBPs (e.g., nonanal) persist for months or more at emission rates large enough to result in indoor concentrations that exceed their odor

  9. Electrochemical Dissolution Behavior and the Residue Formation Mechanism of Laboratory Made Carbonyl Nickel

    International Nuclear Information System (INIS)

    Highlights: • Why residue is formed during anodic dissolution of carbonyl nickel was explained. • Spatiotemporal pattern of pitting in anodic Ni dissolution was described. • The role of sulfur impurities on anodic Ni dissolution was explained. - Abstract: The anodic dissolution of two laboratory-made Ni samples obtained using the carbonyl method was investigated to understand the origin of residue formation in the anode basket in an electroplating tank. The first sample was obtained with 3 ppm addition of carbonyl sulfide to introduce a small amount of sulfur (CN-S sample). The second was obtained without sulfur impurities (CN sample). Linear sweep voltammetry and chronopotentiometry were applied to characterize the dissolution of these samples. The dissolution of the CN-S sample took place in the active region at low overpotentials. This behavior is determined by the presence of sulfur impurities that break down the passive layer and facilitate Ni dissolution. The CN sample without sulfur was dissolved at high overpotentials. The overpotential-time plots displayed regular large amplitude oscillations in which the overvoltage periodically moved between the transpassive and passive regimes. The anodic dissolution of this sample was controlled by two competing processes: breakdown and formation of the passive layer. Scanning electron microscopy and white light interference microscopy were applied to monitor the morphological changes of the two samples as a function of the dissolution time. The results of these studies showed that the CN-S sample dissolved uniformly across the surface. However, the roughness and the aspect ratio of the protruding features on the surface increased with time. This sample produced a fine residue due to detachment of small protruding crystallites. In contrast, the dissolution of the CN sample involved pit formation and took place predominantly from the bulk of the pits. The dissolution of this sample left a porous skeleton of more

  10. Assignment of congested NMR spectra: Carbonyl backbone enrichment via the Entner Doudoroff pathway

    Science.gov (United States)

    Goldbourt, Amir; Day, Loren A.; McDermott, Ann E.

    2007-12-01

    In NMR spectra of complex proteins, sparse isotope enrichment can be important, in that the removal of many 13C- 13C homonuclear J-couplings can narrow the lines and thereby facilitate the process of spectral assignment and structure elucidation. We present a simple scheme for selective yet extensive isotopic enrichment applicable for production of proteins in organisms utilizing the Entner-Doudoroff (ED) metabolic pathway. An enrichment scheme so derived is demonstrated in the context of a magic-angle spinning solid-state NMR (MAS SSNMR) study of Pf1 bacteriophage, the host of which is Pseudomonas aeruginosa, strain K (PAK), an organism that uses the ED pathway for glucose catabolism. The intact and infectious Pf1 phage in this study was produced by infected PAK cells grown on a minimal medium containing 1- 13C D-glucose ( 13C in position 1) as the sole carbon source, as well as 15NH 4Cl as the only nitrogen source. The 37 MDa Pf1 phage consists of about 93% major coat protein, 1% minor coat proteins, and 6% single-stranded, circular DNA. As a consequence of this composition and the enrichment scheme, the resonances in the MAS SSNMR spectra of the Pf1 sample were almost exclusively due to carbonyl carbons in the major coat protein. Moreover, 3D heteronuclear NCOCX correlation experiments also show that the amino acids leucine, serine, glycine, and tyrosine were not isotopically enriched in their carbonyl positions (although most other amino acids were), which is as expected based upon considerations of the ED metabolic pathway. 3D NCOCX NMR data and 2D 15N- 15N data provided strong verification of many previous assignments of 15N amide and 13C carbonyl shifts in this highly congested spectrum; both the semi-selective enrichment patterns and the narrowed linewidths allowed for greater certainty in the assignments as compared with use of uniformly enriched samples alone.

  11. Sol–gel method as a way of carbonyl iron powder surface modification for interaction improvement

    Energy Technology Data Exchange (ETDEWEB)

    Małecki, P., E-mail: pawel.malecki@pwr.edu.pl [Polymer Engineering and Technology Division, W-3, Wrocław University of Technology, Smoluchowskiego 25, 50 370 Wrocław (Poland); Kolman, K.; Pigłowski, J. [Polymer Engineering and Technology Division, W-3, Wrocław University of Technology, Smoluchowskiego 25, 50 370 Wrocław (Poland); Kaleta, J. [Department of Mechanics, Materials Science and Engineering, W-10, Wrocław University of Technology, Smoluchowskiego 25, 50-370 Wrocław (Poland); Krzak, J., E-mail: justyna.krzak@pwr.edu.pl [Department of Mechanics, Materials Science and Engineering, W-10, Wrocław University of Technology, Smoluchowskiego 25, 50-370 Wrocław (Poland)

    2015-03-15

    This article presents a method for modification of carbonyl iron particles’ surface (CIP), (d{sub 50}=4–9 µm) by silica coatings obtained using the sol–gel method. Reaction parameters were determined to obtain dry magnetic powder with homogeneous silica coatings without further processing and without any by-product in the solid or liquid phase. This approach is new among the commonly used methods of silica coating of iron particles. No attempt has been made to cover a carbonyl iron surface by silica in a waste-free method, up to date. In the current work two different silica core/shell structures were made by the sol–gel process, based on different silica precursors: tetraethoxy-silane (TEOS) and tetramethoxy-silane (TMOS). The dependence between the synthesis procedure and thickness of silica shell covering carbonyl iron particles has been described. Surface morphology of the modified magnetic particles and the coating thickness were characterized with the use of scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Determination of the physicochemical structure of the obtained materials was performed by the energy-dispersive X-ray spectroscope (EDS), and the infrared technique (IR). The surface composition was analyzed using X-ray photoelectron spectroscopy (XPS). Additionally, distribution of particle size was measured using light microscopy. The new, efficient process of covering micro-size CIP with a nanometric silica layer was shown. Results of a performed analysis confirm the effectiveness of the presented method. - Highlights: • Proper covering CIP by sol–gel silica layer avoids agglomeration. • A new solid waste-free method of CIP coating is proposed. • Examination of the properties of modified CIP in depends on washing process. • Coatings on CIP particles doesn’t change the magnetic properties of particles.

  12. The Accelerated Test of Chloride Permeability of Concrete

    Institute of Scientific and Technical Information of China (English)

    TAN Ke-feng; ODD E Gjφrv

    2003-01-01

    The availability of accelerated chloride permeability test and the effect of w/c ratio, incorporation of silica fume, maximum aggregate size and aggregate type on the chloride permeability were studied. The mathematic analysis certifies that there is a linear relationship between accelerated test and natural diffusion. Test results show that the chloride permeability of concrete increases as w/c ratio increases whilst a limited amount of replacement of cement with silica fume, the chloride permeability decreases dramatically. The maximum aggregate size in the range of 8 to 25 mm seems also affect chloride permeability but with a much less significant level. The chloride permeability of silica fume lightweight aggregate concrete is very low, especially the concrete made with dry lightweight concrete. The chloride permeability can be evaluated by this accelerated test method.

  13. Chloride regulates afferent arteriolar contraction in response to depolarization

    DEFF Research Database (Denmark)

    Hansen, P B; Jensen, B L; Skott, O

    1998-01-01

    -Renal vascular reactivity is influenced by the level of dietary salt intake. Recent in vitro data suggest that afferent arteriolar contractility is modulated by extracellular chloride. In the present study, we assessed the influence of chloride on K+-induced contraction in isolated perfused rabbit...... afferent arterioles. In 70% of vessels examined, K+-induced contraction was abolished by acute substitution of bath chloride. Consecutive addition of Cl- (30, 60, 80, 100, 110, and 117 mmol/L) restored the sensitivity to K+, and half-maximal response was observed at 82 mmol/L chloride. The calcium channel...... antagonist diltiazem (10(-6) mol/L) abolished K+-induced contractions. Bicarbonate did not modify the sensitivity to chloride. Norepinephrine (10(-6) mol/L) induced full contraction in depolarized vessels even in the absence of chloride. Iodide and nitrate were substituted for chloride with no inhibitory...

  14. Electromagnetic properties of carbonyl iron and their microwave absorbing characterization as filler in silicone rubber

    Indian Academy of Sciences (India)

    Yuping Duan; Guofang Li; Lidong Liu; Shunhua Liu

    2010-10-01

    The complex permittivity, permeability and microwave-absorbing properties of rubber composites filled with carbonyl iron are measured at frequencies from 2–18 GHz. The results indicate that the reflection loss peak shifts towards low frequency region with increasing layer thickness or increasing weight concentration. The minimum reflection loss value of –23.06 dB was obtained at 3.3 GHz for the composites with 80% wt. These results show that the composites possess good microwave absorbing ability in both low- and highfrequency bands.

  15. Determination of carbonyl compounds in air by HPLC; Determinacion de compuestos carbonilicos en aire por HPLC

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, S.; Perez, R.M.; Campos, A.; Gonzalez, D.

    1995-07-01

    A method for the determination of seven carbonyl compounds in air is presented. The procedure involve sampling of air by a Sep-Pak Cartridge impregnated with 2,4-dinitrophenylhydrazine. Elution was done with 3 mL of acetonitrile and the eluate was diluted to 5 mL. The analysis was done by HPLC with UV detection and external standard method quantification. It has been achieved relative standard deviations about 5% and detection limits of 80 ng/cartridge for formaldehyde, acetaldehyde and acetoacetonitrile. Three different types of samples (rural, urban, petrol emission) were successfully analyzed. (Author) 12 refs.

  16. Calculation of High Frequency Complex Permeability of Carbonyl Iron Flakes in a Nomagnetic Matrix

    Institute of Scientific and Technical Information of China (English)

    WEN Fu-Sheng; QIAO Liang; YI Hai-Bo; ZHOU Dong; LI Fa-Shen

    2008-01-01

    The carbonyl iron flakes are fabricated by high-energy ball milling.The effective permeability is measured and calculated for the composite consisting of flakes embedded in a nonmagnetic matrix.The magnetic flakes with a shape anisotropy and random spatial distribution of normal direction are considered to calculate the complex permeability of magnetic flake materials.Its analytical model is derived from the Landau-Lifshitz- Gilbert equation and Bruggeman's effective medium theory.The calculated results agree well with the experiment.

  17. Non-Enzymatic Modification of Aminophospholipids by Carbonyl-Amine Reactions

    Directory of Open Access Journals (Sweden)

    Reinald Pamplona

    2013-02-01

    Full Text Available Non-enzymatic modification of aminophospholipids by lipid peroxidation-derived aldehydes and reducing sugars through carbonyl-amine reactions are thought to contribute to the age-related deterioration of cellular membranes and to the pathogenesis of diabetic complications. Much evidence demonstrates the modification of aminophospholipids by glycation, glycoxidation and lipoxidation reactions. Therefore, a number of early and advanced Maillard reaction-lipid products have been detected and quantified in different biological membranes. These modifications may be accumulated during aging and diabetes, introducing changes in cell membrane physico-chemical and biological properties.

  18. A green synthesis of α,β-unsaturated carbonyl compounds from glyceraldehyde acetonide

    Directory of Open Access Journals (Sweden)

    Cláudia O. Veloso

    2011-01-01

    Full Text Available The catalytic behavior of Cs-exchanged and Cs-impregnated zeolites (X and Y was studied using the Knoevenagel condensation between glyceraldehyde acetonide and ethyl acetoacetate in order to produce the corresponding α,β-unsaturated carbonyl compound that is an important intermediate for fine chemicals. The influence of reaction temperature, type of zeolite, and basicity of the sites on the catalytic behavior of the samples was evaluated. All zeolites were active for the studied reaction. The formation of the main condensation product was favored at lower reaction temperatures. Products of further condensations were also observed especially for samples that were only dried before catalytic test.

  19. Multiband microwave absorption films based on defective multiwalled carbon nanotubes added carbonyl iron/acrylic resin

    Energy Technology Data Exchange (ETDEWEB)

    Li Yong, E-mail: liyong1897@163.co [Institute of Naval Logistic Technology and Equipment of PLA, Beijing 100072 (China); Chen Changxin, E-mail: chen.c.x@sjtu.edu.c [National Key Laboratory of Nano/Micro Fabrication Technology, Key Laboratory for Thin Film and Microfabrication of the Ministry of Education, Research Institute of Micro/Nano Science and Technology, Shanghai Jiao Tong University, Shanghai 200240 (China); Pan Xiaoyan [School of Materials Science and Engineering, East China University of Science and Technology, Shanghai 200237 (China); Ni Yuwei; Zhang Song; Huang, Jie [Institute of Naval Logistic Technology and Equipment of PLA, Beijing 100072 (China); Chen Da; Zhang Yafei [National Key Laboratory of Nano/Micro Fabrication Technology, Key Laboratory for Thin Film and Microfabrication of the Ministry of Education, Research Institute of Micro/Nano Science and Technology, Shanghai Jiao Tong University, Shanghai 200240 (China)

    2009-05-01

    Defective multiwalled carbon nanotubes (MWCNTs) were introduced to the carbonyl iron (CI) based composites to improve its microwave absorption by a simple ultrasonic mixing process. The electromagnetic parameters were measured in the 2-18 GHz range. Microwave absorption of CI based composites with 2 mm in thickness was evidently enhanced by adding as little as 1.0 wt% defective MWCNTs with two well separated absorption peaks exceeding -20 dB, as compared with that of pure CI based and defective MWCNTs composites. The enhancement mechanism is thought due to the interaction and better electromagnetic match between defective MWCNTs and ferromagnetic CI particles.

  20. Elevated Levels of Carbonyl Compounds in the Atmosphere of Eastern Himalaya in India

    Science.gov (United States)

    Sarkar, C.; Chatterjee, A.; Majumdar, D.; Raha, S.; Ghosh, S. K.; Srivastava, A.

    2015-12-01

    A first ever study on atmospheric carbonyl compounds (CC) were made over eastern Himalaya in India. Samples were collected over a high altitude hill station, Darjeeling (27.01°N, 88.15°E, 2200 masl) during 2011-2012. It is well known that CC have toxic and carcinogenic properties as well as they have important effects on regional climate. Therefore their presence in the environment is of great concern especially for the Himalayan region because of the ecological and geographical importance of the area. The average annual concentration of total CCs was 293.3 ± 463.9 μgm-3 with maximum during post monsoon (1104.8 ± 568.0 μgm-3) and minimum during winter season (72.2 ± 42.9 μgm-3). Darjeeling experiences huge emissions of carbonaceous pollutants from massive influx of tourists during premonsoon and postmonsoon seasons. Though the emission strength could be comparable, the loss of carbonyls from the atmosphere could be due to photochemical degradation under high solar insolation during premonsoon. Acetone was most abundant species with an annual average concentration of 200.8±352.9 μgm-3 with 70 % contribution to the total CCs measured. Interestingly, acetone over Darjeeling was found to be much higher than most of the metropolitan cities in the world. The average formaldehyde to acetaldehyde ratio (1.64 ± 1.43) over Darjeeling is a good representation of a typical urban atmosphere at this high altitude over this part of Himalaya. High carbonyl concentration over eastern Himalaya compared to other megacities across the globe could be attributed to uncontrolled activities related to development in tourism, high population density and moreover it's unique orography and land use pattern with narrow roads, unplanned township etc. The unscientific treatment of human and animal and other domestic waste is another major concern which significantly contribute to carbonyl and other carbonaceous pollutants over this part of Himalaya.

  1. LASER-INDUCED DECOMPOSITION OF METAL CARBONYLS FOR CHEMICAL VAPOR DEPOSITION OF MICROSTRUCTURES

    OpenAIRE

    Tonneau, D.; Auvert, G.; Pauleau, Y.

    1989-01-01

    Tungsten and nickel carbonyls were used to produce metal microstructures by laser-induced chemical vapor deposition (CVD) on various substrates. The deposition rate of microstructures produced by thermodecomposition of W(CO)6 on Si substrates heated with a cw Ar+ laser beam was relatively low (10 to 30 nm/s) even at high temperatures (above 900°C). Ni microstructures were deposited on quartz substrates irradiated with a CO2 laser beam. Relatively high laser powers were needed to heat the Ni s...

  2. Carbonyl sulfide detection with a thermoelectrically cooled midinfrared quantum cascade laser

    Science.gov (United States)

    Roller, Chad; Kosterev, Anatoliy A.; Tittel, Frank K.; Uehara, Kiyoji; Gmachl, Claire; Sivco, Deborah L.

    2003-11-01

    A compact absorption spectrometer with a midinfrared tunable quantum cascade laser operating at 4.86 μm (2054 cm-1) is used to measure lower concentrations of carbonyl sulfide (COS) in air. A detection sensitivity of ~30 parts in 109 of COS and the selectivity of two stable isotopes, 12C16O32S and 12C16O34S, are demonstrated. Specifically, the feasibility of detecting COS in expired human breath as a potential noninvasive medical diagnostic tool is investigated.

  3. STUDY OF CARBONYLATION OF METHANOL TO ACETIC ACID AND ACETIC ANHYDRIDE OVER A BIDENTATE POLYMER BOUND CIS-DICARBONYLRHODIUM COMPLEX AS CATALYST

    Institute of Scientific and Technical Information of China (English)

    WANG Xiaojun; LIU Zhongyang; PAN Pinglai; YUAN Guoqing

    1996-01-01

    Copolymer of 2-vinylpyridine and vinylacetate coordinated with dicarbonylrhodium used as a catalyst for carbonylation of methanol to acetic acid and anhydride has been studied. The structural characteristics of the copolymer ligand and complex, and the influences of the reaction conditions on the carbonylation catalyzed by this polymer complex have been investigated. In comparison with small molecule catalyst of Rh complex, the bidentate copolymer coordinated complex has better thermal stability. The reaction mechanism of the carbonylation reaction is also illustrated.

  4. 40 CFR 61.64 - Emission standard for polyvinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... Standard for Vinyl Chloride § 61.64 Emission standard for polyvinyl chloride plants. An owner or operator of a polyvinyl chloride plant shall comply with the requirements of this section and § 61.65. (a... is not to exceed 0.02 g vinyl chloride/kg (0.04 lb vinyl chloride/ton) of polyvinyl chloride...

  5. Determination of gaseous and particulate carbonyls (glycolaldehyde, hydroxyacetone, glyoxal, methylglyoxal, nonanal and decanal in the atmosphere at Mt. Tai

    Directory of Open Access Journals (Sweden)

    K. Kawamura

    2013-01-01

    Full Text Available Gaseous and particulate semi-volatile carbonyl compounds were determined every three hours in the atmosphere of Mount Tai (elevation, 1534 m in the North China Plain during 2–5, 23–24 and 25 June, 2006 under a clear sky condition. Using two-step filter cartridge in a series, particulate carbonyls were first collected on a quartz filter and then gaseous carbonyls were collected on a quartz filter impregnated with O-benzylhydroxylamine (BHA. After the two-step derivatization with BHA and N,O-bis(trimethylsilyltrifluoroacetamide (BSTFA, carbonyl derivatives were measured using a gas chromatography. The gaseous concentrations were obtained as follow: glycolaldehyde (range 0–1271 ng m−3, average 555 ng m−3, hydroxyacetone (0–707 ng m−3, 163 ng m−3, glyoxal (198–1396 ng m−3, 720 ng m−3, methylglyoxal (410–3170 ng m−3, 1376 ng m−3, n-nonanal (0–236 ng m−3, 71 ng m−3, and n-decanal (0–159 ng m−3, 31 ng m−3. These concentrations are among the highest ever reported in the urban and forest atmosphere. We found that gaseous carbonyls are more than 10 times more abundant than particulate carbonyls. Time-resolved variations of carbonyls did not show any a clear diurnal pattern, except for hydroxyacetone. We found that glyoxal, methylglyoxal and glycolaldehyde positively correlated with levoglucosan (a tracer of biomass burning, suggesting that a contribution from field burning of agricultural wastes (wheat crops is significant for the bifunctional carbonyls in the atmosphere of Mt. Tai. Upward transport of the pollutants to the mountaintop from the low lands in the North China Plain is a major process to control the distributions of carbonyls in the upper atmosphere over Mt. Tai.

  6. Cytoprotective Effects of Hydrophilic and Lipophilic Extracts of Pistacia vera against Oxidative Versus Carbonyl Stress in Rat Hepatocytes.

    Science.gov (United States)

    Shahraki, Jafar; Zareh, Mona; Kamalinejad, Mohammad; Pourahmad, Jalal

    2014-01-01

    This study was conducted to evaluate the cytoprotection of various extracts and bioactive compounds found in Pistacia vera againts cytotoxicity, ROS formation, lipid peroxidation, protein carbonylation, mitochondrial and lysosomal membrane damages in cell toxicity models of diabetes related carbonyl (glyoxal) and oxidative stress (hydroperoxide). Methanol, water and ethyl acetate were used to prepare crude pistachios extracts, which were then used to screen for in-vitro cytoprotection of freshly isolated rat hepatocytes against these toxins. The order of protection by Pistacia vera extracts against both hydroperoxide induced oxidative stress (ROS formation) and glyoxal induced protein carbonylation was: pistachio methanolic extract >pistachio water extract, gallic acid, catechin> α-tochoferol and pistachio ethyl acetate extract. Finally due to higher protection achieved by methanolic extract even compared to sole pretreatment of gallic acid, catechin or α-tochoferol, we suggest that cytoprotection depends on the variety of polar and non-polar compounds found in methanolic extract, it is likely that multiple cytoprotective mechanisms are acting against oxidative and carbonyl induced cytotoxicity. To our knowledge, we are the first to report the cytoprotective activity of Pistacia vera extracts against oxidative and carbonyl stress seen in type 2 diabetes hepatocytes model. PMID:25587316

  7. Engineered Trx2p industrial yeast strain protects glycolysis and fermentation proteins from oxidative carbonylation during biomass propagation

    Directory of Open Access Journals (Sweden)

    Gómez-Pastor Rocío

    2012-01-01

    Full Text Available Abstract Background In the yeast biomass production process, protein carbonylation has severe adverse effects since it diminishes biomass yield and profitability of industrial production plants. However, this significant detriment of yeast performance can be alleviated by increasing thioredoxins levels. Thioredoxins are important antioxidant defenses implicated in many functions in cells, and their primordial functions include scavenging of reactive oxygen species that produce dramatic and irreversible alterations such as protein carbonylation. Results In this work we have found several proteins specifically protected by yeast Thioredoxin 2 (Trx2p. Bidimensional electrophoresis and carbonylated protein identification from TRX-deficient and TRX-overexpressing cells revealed that glycolysis and fermentation-related proteins are specific targets of Trx2p protection. Indeed, the TRX2 overexpressing strain presented increased activity of the central carbon metabolism enzymes. Interestingly, Trx2p specifically preserved alcohol dehydrogenase I (Adh1p from carbonylation, decreased oligomer aggregates and increased its enzymatic activity. Conclusions The identified proteins suggest that the fermentative capacity detriment observed under industrial conditions in T73 wine commercial strain results from the oxidative carbonylation of specific glycolytic and fermentation enzymes. Indeed, increased thioredoxin levels enhance the performance of key fermentation enzymes such as Adh1p, which consequently increases fermentative capacity.

  8. Relation between chloride exchange diffusion and a conductive chloride pathway across the isolated skin of the toad (Bufo bufo)

    DEFF Research Database (Denmark)

    Kristensen, P; Larsen, Erik Hviid

    1978-01-01

    Substitution of chloride in the outside bathing medium of the toad skin with bromide, iodide, nitrate and sulphate leads to a reduction in the apparent exchange diffusion of chloride across this tissue, and also to a reduction of the chloride current recorded during hyperpolarization. A series...... of inhibitors (thiocyanate, furosemide, phloretin, and acetazolamide) also affects chloride exchange diffusion, hyperpolarization current as well as chloride influx during hyperpolarization. Although in some cases, effects on the short circuit current were also observed none of the effects on chloride transport....... On the basis of these findings, and the results reported in the previous paper (Hviid Larsen and Kristensen 1977) it is considered probable that the membrane molecules responsible to chloride exchange diffusion under short circuit conditions, are rearranged under the influence of a hyperpolarizing clamping...

  9. Anti-chloride permeability and anti-chloride corrodibility of a green high performance concrete admixture in concrete

    Institute of Scientific and Technical Information of China (English)

    ZHENG Yongbao; LIU Xinrong; LIU Dongyan; CHEN Jiangong; HUANG Xiongjun

    2003-01-01

    The effects of green high performance concrete (GHPC) admixture on the anti-chloride permeability and anti- chloride corrodibility of concrete are studied by a series of experiments designed on the basis of the diffusion principle and electrochemical principle. The GHPC admixture consists of fly ash, gangue, slag, red mud, etc., of which the mass fraction of industrial residues is over 96 %. The anti-permeabilities and anti-corrodibilities of the tested GHPC and normal concrete (NC) are evaluated by the Diffusion Coefficients of chloride which was obtained by measuring the concentration of chloride in the tested systems by the voltage difference method. It is found that the adoption of GHPC admixture greatly improves the anti-chloride permeability and anti-chloride corrodibility by modifying the inner structure and contracting the porosity of concrete to the reduce considerably the diffusion rate of chloride. The admixture is desirable regarding its engineering performances as well as economical and environmental interests.

  10. Synthesis, spectroscopic characterization, solid state d.c. electrical conductivity and biological studies of some lanthanide(III chloride complexes with a heterocyclic Schiff base ligand

    Directory of Open Access Journals (Sweden)

    K. Mohanan

    2016-07-01

    Full Text Available Condensation of 2-hydroxy-1-naphthaldehyde with 2-amino-3-carboxyethyl-4,5-dimethylthiophene in 1:1 molar ratio, yielded a potentially tridentate Schiff base viz. 2-[N-(2′-hydroxy-1-naphthylideneamino]-3-carboxyethyl-4,5-dimethylthiophene (HNAT. This ligand formed complexes with lanthanum(III, cerium(III, praseodymium(III, neodymium(III, samarium(III, europium(III and gadolinium(III chloride under well defined conditions. These complexes were characterized through elemental analysis, molar conductance, magnetic moment measurements, IR, UV–Vis, FAB mass and 1H NMR spectral studies. Analytical data showed that all the metal complexes exhibited 1:1 metal–ligand ratio. Molar conductance values adequately confirmed the non-electrolytic nature of the metal complexes. The proton NMR spectral observations supplement the IR spectral assignments. The spectral data revealed that the ligand acted as neutral tridentate, coordinating to the metal ion through azomethine nitrogen, ester carbonyl and naphtholate oxygen without deprotonation. The ligand and its lanthanum(III chloride complex were subjected to XRD studies. The lanthanum(III chloride complex has undergone a facile transesterification reaction. The solid state d.c. electrical conductivity of some selected complexes were measured as a function of temperature, indicating the semiconducting nature of the metal complexes. The antimicrobial activities were examined by disk diffusion method against some pathogenic bacterial and fungal species.

  11. CO dissociation on Ni: The effect of steps and of nickel carbonyl

    DEFF Research Database (Denmark)

    Engbæk, Jakob; Lytken, Ole; Nielsen, Jane Hvolbæk;

    2008-01-01

    The dissociation of CO was investigated on a stepped Ni(141313) crystal. The experiments show that the monoatomic steps completely dominate the dissociation of CO on the nickel surface. The activation energy for dissociation of CO along the steps is measured at 500 K to be 150 kJ/mol in the press......The dissociation of CO was investigated on a stepped Ni(141313) crystal. The experiments show that the monoatomic steps completely dominate the dissociation of CO on the nickel surface. The activation energy for dissociation of CO along the steps is measured at 500 K to be 150 k......J/mol in the pressure range 1-7 X 10(-6) mbar CO. Poisoning the steps by preadsorbing 0.05 ML sulfur, the dissociation rate was reduced by more than a factor of 50 clearly providing evidence for the step activity. Furthermore, by deliberately adding remote amounts of nickel carbonyl (0.25%) to the CO gas, it is shown...... that the dissociation probability of CO is increased by a factor of 60 compared to when using a purified CO gas. This clearly demonstrates the importance of avoiding nickel carbonyl when CO dissociation is studied. CO dissociation is important because it is believed to be the rate limiting step in methanation...

  12. Enhanced microwave absorbing properties and heat resistance of carbonyl iron by electroless plating Co

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Hongyu, E-mail: wanghongyu07010310@163.com; Zhu, Dongmei; Zhou, Wancheng; Luo, Fa

    2015-11-01

    Co coated carbonyl iron particles (Co (CI)) are fabricated through electroless plating method, and the electromagnetic microwave absorbing properties are investigated in the frequencies during 8.2–12.4 GHz. The complex permittivity of CI particles after electroless plating Co is higher than that of raw CI particles due to improvment of the polarization process. Furthermore, according to the XRD and TG results, the Co layer can enhance the heat resistance of CI particles. The bandwidth below −10 dB can reach 3.9 GHz for the Co(CI) absorbent. The results indicate that the electroless plating Co not only enhances the absorbing properties but also improves the heat resistance of CI. - Highlights: • The Co-coated carbonyl iron Co(CI) particles were prepared by electroless plating. • The electromagnetic wave absorbing properties of Co(CI) particles were studied. • The heat treatment on the absorbing property of Co(CI) particles was studied. • The Co(CI) particles have good absorbing property when compared with CI.

  13. Impact of silica-coating on the microwave absorption properties of carbonyl iron powder

    International Nuclear Information System (INIS)

    Microwave absorption properties, especially the band width and depth of reflection loss are highlighted as key measurement in studies of microwave absorber. In order to improve the band width and depth of reflection loss of carbonyl iron powder (CIP), we prepared SiO2 layers on the surface of CIP by using tetraethyl orthosilicate (TEOS) as a SiO2 source and 3-aminopropyl triethoxysilane (APTES) as a surface modifier. SiO2 layer was formed by the hydrolysis of TEOS. The results show that after treatment the CIP is covered by a 5–10 nm coating layer. Contrast to uncoated samples, coated samples show improved absorption properties. The minimum of reflection loss is −38.8 dB at 11 GHz and the band width of reflection loss exceeding −10 dB is from 8 GHz to 14 GHz. - Highlights: • Silica coatings were prepared on the surface of carbonyl iron powder. • Coating layers were identified by several ways. • We discussed the absorbing mechanism of coated samples. • Reflection loss was significantly improved, the width of RL exceeding −10 dB is from 8 GHz to 14 GHz

  14. Analysis of the carbonyl group stretching vibrations in some structural fragments of poly-3-hydroxybutyrate

    CERN Document Server

    Pitsevich, George A; Doroshenko, Iryna

    2016-01-01

    The structure and the medium effects exerted on the spectral characteristics of the carbonyl group stretching vibrations in some structural fragments of poly-3-hydroxybutyrate have been analyzed. Calculations of the equilibrium configurations and IR spectra were carried out using the Gaussian program set in the approximation B3LYP/cc-pVDZ. It has been shown that typical bending of the poly-3-hydroxybutyrate chain is observed with an increase in the number of structural units. In order to explain the difference between the calculated and experimental frequencies of the C=O group stretching vibrations, the calculations of the potential energy curve associated with variations in the length of C=O bond and the subsequent numerical solution of a one-dimensional vibrational Schr\\"odinger equation have been performed. The medium effects have been taken into account within the scope of a polarizable continuum model. Owing to the inclusion of the above-mentioned factors, which affect frequencies of the carbonyl groups...

  15. Impact of silica-coating on the microwave absorption properties of carbonyl iron powder

    Energy Technology Data Exchange (ETDEWEB)

    Li, J. [School of Science, Lanzhou University of Technology, Lanzhou, Gansu 730050 (China); Feng, W.J., E-mail: wjfeng@lut.cn [State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metal, Lanzhou University of Technology, Lanzhou 730050 (China); School of Science, Lanzhou University of Technology, Lanzhou, Gansu 730050 (China); Wang, J.S.; Zhao, X.; Zheng, W.Q. [School of Science, Lanzhou University of Technology, Lanzhou, Gansu 730050 (China); Yang, H. [State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metal, Lanzhou University of Technology, Lanzhou 730050 (China); School of Science, Lanzhou University of Technology, Lanzhou, Gansu 730050 (China)

    2015-11-01

    Microwave absorption properties, especially the band width and depth of reflection loss are highlighted as key measurement in studies of microwave absorber. In order to improve the band width and depth of reflection loss of carbonyl iron powder (CIP), we prepared SiO{sub 2} layers on the surface of CIP by using tetraethyl orthosilicate (TEOS) as a SiO{sub 2} source and 3-aminopropyl triethoxysilane (APTES) as a surface modifier. SiO{sub 2} layer was formed by the hydrolysis of TEOS. The results show that after treatment the CIP is covered by a 5–10 nm coating layer. Contrast to uncoated samples, coated samples show improved absorption properties. The minimum of reflection loss is −38.8 dB at 11 GHz and the band width of reflection loss exceeding −10 dB is from 8 GHz to 14 GHz. - Highlights: • Silica coatings were prepared on the surface of carbonyl iron powder. • Coating layers were identified by several ways. • We discussed the absorbing mechanism of coated samples. • Reflection loss was significantly improved, the width of RL exceeding −10 dB is from 8 GHz to 14 GHz.

  16. Comparative Proteomic Analysis of Carbonylated Proteins from the Striatum and Cortex of Pesticide-Treated Mice

    Directory of Open Access Journals (Sweden)

    Christina Coughlan

    2015-01-01

    Full Text Available Epidemiological studies indicate exposures to the herbicide paraquat (PQ and fungicide maneb (MB are associated with increased risk of Parkinson’s disease (PD. Oxidative stress appears to be a premier mechanism that underlies damage to the nigrostriatal dopamine system in PD and pesticide exposure. Enhanced oxidative stress leads to lipid peroxidation and production of reactive aldehydes; therefore, we conducted proteomic analyses to identify carbonylated proteins in the striatum and cortex of pesticide-treated mice in order to elucidate possible mechanisms of toxicity. Male C57BL/6J mice were treated biweekly for 6 weeks with saline, PQ (10 mg/kg, MB (30 mg/kg, or the combination of PQ and MB (PQMB. Treatments resulted in significant behavioral alterations in all treated mice and depleted striatal dopamine in PQMB mice. Distinct differences in 4-hydroxynonenal-modified proteins were observed in the striatum and cortex. Proteomic analyses identified carbonylated proteins and peptides from the cortex and striatum, and pathway analyses revealed significant enrichment in a variety of KEGG pathways. Further analysis showed enrichment in proteins of the actin cytoskeleton in treated samples, but not in saline controls. These data indicate that treatment-related effects on cytoskeletal proteins could alter proper synaptic function, thereby resulting in impaired neuronal function and even neurodegeneration.

  17. Comparative Proteomic Analysis of Carbonylated Proteins from the Striatum and Cortex of Pesticide-Treated Mice

    Science.gov (United States)

    Coughlan, Christina; Walker, Douglas I.; Lohr, Kelly M.; Richardson, Jason R.; Saba, Laura M.; Caudle, W. Michael; Fritz, Kristofer S.; Roede, James R.

    2015-01-01

    Epidemiological studies indicate exposures to the herbicide paraquat (PQ) and fungicide maneb (MB) are associated with increased risk of Parkinson's disease (PD). Oxidative stress appears to be a premier mechanism that underlies damage to the nigrostriatal dopamine system in PD and pesticide exposure. Enhanced oxidative stress leads to lipid peroxidation and production of reactive aldehydes; therefore, we conducted proteomic analyses to identify carbonylated proteins in the striatum and cortex of pesticide-treated mice in order to elucidate possible mechanisms of toxicity. Male C57BL/6J mice were treated biweekly for 6 weeks with saline, PQ (10 mg/kg), MB (30 mg/kg), or the combination of PQ and MB (PQMB). Treatments resulted in significant behavioral alterations in all treated mice and depleted striatal dopamine in PQMB mice. Distinct differences in 4-hydroxynonenal-modified proteins were observed in the striatum and cortex. Proteomic analyses identified carbonylated proteins and peptides from the cortex and striatum, and pathway analyses revealed significant enrichment in a variety of KEGG pathways. Further analysis showed enrichment in proteins of the actin cytoskeleton in treated samples, but not in saline controls. These data indicate that treatment-related effects on cytoskeletal proteins could alter proper synaptic function, thereby resulting in impaired neuronal function and even neurodegeneration. PMID:26345149

  18. Penicitroamide, an Antimicrobial Metabolite with High Carbonylization from the Endophytic Fungus Penicillium sp. (NO. 24

    Directory of Open Access Journals (Sweden)

    Zi-Wei Feng

    2016-10-01

    Full Text Available Penicitroamide (1, a new metabolite with a new framework, was isolated from the ethyl acetate extract of the PDB (Potato Dextrose Broth medium of Penicillium sp. (NO. 24. The endophytic fungus Penicillium sp. (NO. 24 was obtained from the healthy leaves of Tapiscia sinensis Oliv. The structure of penicitroamide (1 features a bicyclo[3.2.1]octane core unit with a high degree of carbonylization (four carbonyl groups and one enol group. The chemical structure of penicitroamide (1 was elucidated by analysis of 1D-, 2D-NMR and MS data. In bioassays, penicitroamide (1 displayed antibacterial potency against two plant pathogens, Erwinia carotovora subsp. Carotovora (Jones Bersey, et al. and Sclerotium rolfsii Sacc. with MIC50 at 45 and 50 μg/mL. Compound 1 also showed 60% lethality against brine shrimp at 10 μg/mL. Penicitroamide (1 exhibited no significant activity against A549, Caski, HepG2 and MCF-7 cells with IC50 > 50 μg/mL. Finally, the possible biosynthetic pathway of penicitroamide (1 was discussed.

  19. Protein hydroperoxides and carbonyl groups generated by porphyrin-induced photo-oxidation of bovine serum albumin

    DEFF Research Database (Denmark)

    Silvester, J A; Timmins, G S; Davies, Michael Jonathan

    1998-01-01

    disruption of the indole ring system. This study shows that these photo-oxidation processes also consume oxygen and give rise to hydrogen peroxide, protein hydroperoxides, and carbonyl functions. The yield of hydrogen peroxide, protein hydroperoxides, and carbonyl functions is shown to be dependent...... on illumination time, the nature of the sensitizer, and the concentration of oxygen; the yield of hydroperoxides can also be markedly diminished by the presence of a spin trap which reacts with the initial protein radicals. The mechanism of formation of the protein hydroperoxides is suggested to be primarily...... through type I processes (i.e., independent of singlet oxygen), while type II (singlet oxygen) mechanisms may play a significant role in protein carbonyl formation. Reaction of the protein hydroperoxide species with metal ion complexes is shown to produce further protein-derived radicals which...

  20. Preparation and biological behaviour of some neutral [sup 99m]Tc-carbonyl dithiocarbamates showing rapid hepatobiliary excretion

    Energy Technology Data Exchange (ETDEWEB)

    Baldas, John; Bonnyman, John (Australian Radiation Lab., Yallambie (Australia))

    1992-10-01

    A simple procedure for the preparation of [sup 99m]Tc-carbonyl complexes of dithiocarbamates in high yield and radiochemical purity has been developed and used for the preparation of [sup 99m]Tc-carbonyl complexes of bis(2-hydroxyethyl)dithiocarbamate and bis(2-hydroxypropyl)dithiocarbamate. These complexes were found to be extremely stable and their biological behaviour was studied in mice and compared to that of the [sup 99m]TcN- and the [sup 99m]Tc-complexes [prepared by dithionite (dit) reduction] of the same ligands. The carbonyl complexes were found to be efficient hepatobiliary agents and cleared more rapidly than the corresponding [sup 99m]TcN- and [sup 99m]Tc(dit)-complexes. (Author).

  1. Model of In Situ Composite of Cobalt(Ⅱ)-Phthalocyanine and Carbonyl Iron for Organic/Inorganic Nanocomposites

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Cobalt-phthalocyanine/iron nanocomposite particles have been obtained using method of composite in situ,with the mixture of carbonyl iron and solution of cobalt(Ⅱ)-phthalocyanine (Co-Pc) ultrasonic dispersing in N,N-dimethyl-formamide (DMF).Structure characterization of their inner and surface have relation with method of carbonyl iron joined in the mixture,contents of carbonyl iron and Co-Pc in the mixture of Co-Pc ultrasonic dispersing in DMF.With a method of composite in situ controlling reasonable experiment condition,it can be obtained that cobalt-phthalocyanine/iron nanocomposite particles has completely been covered with Co-Pc,they had structure of Chinese gooseberry in inner and mere made up of almost regular spherical shape and the average diameter is 1.4 μm.

  2. Infrared Photodissociation Spectra of Mass-Selected Homoleptic Dinuclear Palladium Carbonyl Cluster Cations in the Gas Phase

    Institute of Scientific and Technical Information of China (English)

    崔洁铭; 邢小鹏; 池超贤; 王冠军; 刘智攀; 周鸣飞

    2012-01-01

    Infrared spectra of mass-selected homoleptic dinuclear palladium carbonyl cluster cations Pd2(CO)n (n=5 8) are measured via infrared photodissociation spectroscopy in the carbonyl stretching frequency region. The structures are established by comparison of the experimental spectra with simulated spectra derived from density functional calculations. The Pd2(CO)+ cation is characterized to have two weakly semibridging CO groups with C2 symmetry. The Pd2(CO)6+ and Pd2(CO)7+ cations are determined to involve one weakly semibridging CO group. The Pd2(CO)8+ cation is a CO coordination saturated cluster, which is determined to have a D2d structure with all of the carbonyl groups terminally bonded. Bonding analysis indicates that these cluster cations each has a Pd--Pd half bond. The Pd--Pd distance increases with the number of CO ligands.

  3. Sulfur isotopic analysis of carbonyl sulfide and its application for biogeochemical cycles

    Science.gov (United States)

    Hattori, Shohei; Kamezaki, Kazuki; Ogawa, Takahiro; Toyoda, Sakae; Katayama, Yoko; Yoshida, Naohiro

    2016-04-01

    Carbonyl sulfide (OCS or COS) is the most abundant gas containing sulfur in the atmosphere, with an average mixing ratio of 500 p.p.t.v. in the troposphere. OCS is suggested as a sulfur source of the stratospheric sulfate aerosols (SSA) which plays an important role in Earth's radiation budget and ozone depletion. Therefore, OCS budget should be validated for prediction of climate change, but the global OCS budget is imbalance. Recently we developed a promising new analytical method for measuring the stable sulfur isotopic compositions of OCS using nanomole level samples: the direct isotopic analytical technique of on-line gas chromatography-isotope ratio mass spectrometry (GC-IRMS) using fragmentation ions S+ (Hattori et al., 2015). The first measurement of the δ34S value for atmospheric OCS coupled with isotopic fractionation for OCS sink reactions in the stratosphere (Hattori et al., 2011; Schmidt et al., 2012; Hattori et al., 2012) explains the reported δ34S value for background stratospheric sulfate, suggesting that OCS is a potentially important source for background (nonepisodic or nonvolcanic) stratospheric sulfate aerosols. This new method measuring δ34S values of OCS can be used to investigate OCS sources and sinks in the troposphere to better understand its cycle. It is known that some microorganisms in soil can degrade OCS, but the mechanism and the contribution to the OCS in the air are still uncertain. In order to determine sulfur isotopic enrichment factor of OCS during degradation via microorganisms, incubation experiments were conducted using strains belonging to the genera Mycobacterium, Williamsia and Cupriavidus, isolated from natural soil environments (Kato et al., 2008). As a result, sulfur isotope ratios of OCS were increased during degradation of OCS, indicating that reaction for OC32S is faster than that for OC33S and OC34S. OCS degradation via microorganisms is not mass-independent fractionation (MIF) process, suggesting that this

  4. Gas/particle partitioning of carbonyls in the photooxidation of isoprene and 1,3,5-trimethylbenzene

    Directory of Open Access Journals (Sweden)

    R. M. Healy

    2008-03-01

    Full Text Available A new denuder-filter sampling technique has been used to investigate the gas/particle partitioning behaviour of the carbonyl products from the photooxidation of isoprene and 1,3,5-trimethylbenzene. A series of experiments was performed in two atmospheric simulation chambers at atmospheric pressure and ambient temperature in the presence of NOx and at a relative humidity of approximately 50%. The denuder and filter were both coated with the derivatizing agent O-(2,3,4,5,6-pentafluorobenzyl-hydroxylamine (PFBHA to enable the efficient collection of gas- and particle-phase carbonyls respectively. The tubes and filters were extracted and carbonyls identified as their oxime derivatives by GC-MS. The carbonyl products identified in the experiments accounted for around 5% and 10% of the mass of secondary organic aerosol formed from the photooxidation of isoprene and 1,3,5-trimethylbenzene respectively.

    Experimental gas/particle partitioning coefficients were determined for a wide range of carbonyl products formed from the photooxidation of isoprene and 1,3,5-trimethylbenzene and compared with the theoretical values based on standard absorptive partitioning theory. Photooxidation products with a single carbonyl moiety were not observed in the particle phase, but dicarbonyls, and in particular, glyoxal and methylglyoxal, exhibited gas/particle partitioning coefficients several orders of magnitude higher than expected theoretically. These findings support the importance of heterogeneous chemistry as a pathway for SOA formation and growth during the atmospheric degradation of anthropogenic and biogenic hydrocarbons.

  5. Kinetics and Mechanism of the Gas-Phase Reaction of Selected Carbonyls with Cl Atoms between 250 and 340 K

    Science.gov (United States)

    Hasson, A. S.; Algrim, L.; Abdelhamid, A.; Tyndall, G. S.; Orlando, J. J.

    2013-12-01

    Carbonyls are important products from the gas phase degradation of most volatile organic compounds. Their atmospheric reactions therefore have a significant impact on atmospheric composition, particularly in aged air masses. While the reactions of short-chain linear carbonyls are well understood, the chemistry of larger (> C6) and branched carbonyl is more uncertain. To provide insight into these reactions, the reactions of three carbonyls (methyl isopropyl ketone, MIK; di-isopropyl ketone, DIK; and diethyl ketone, DEK) with chlorine atoms were investigated between 250 and 340 K and 1 atm in the presence and absence of NOx and an HO2 source (methanol). Experiments were performed in a photochemical reactor using a combination of long-path Fourier transform infra-red spectroscopy, proton transfer reaction mass spectrometry and gas chromatography with flame ionization detection. The kinetics were studied using the relative rate technique with butanone and isopropanol as the reference compounds. The Arrhenius expression for the three rate coefficients was determined to be k(DEK+Cl) = 3.87 x 10-11e(2 × 7 kJ/mol)/RT cm3 molecules-1 s-1 , k(MIPK+Cl) = 7.20 x 10-11e(0.2× 8 kJ/mol)/RT cm3 molecules-1 s-1 , and k(DIPK+Cl) = 3.33 x 10-10e(-3× 8 kJ/mol)/RT cm3 molecules-1 s-1 . Measured reaction products accounted for 38-72 % of the reacted carbon and were consistent with strong deactivation of the carbon atom adjacent to the carbonyl group with respect to H-atom abstraction by Cl atoms. The product distributions also provide insight into radical recycling from the organic peroxy + HO2 reaction, and the relative rates of isomerization, fragmentation and reaction with O2 for carbonyl-containing alkoxy radicals. Implications of these results will be discussed.

  6. Methane to acetic acid over Cu-exchanged zeolites: mechanistic insights from a site-specific carbonylation reaction.

    Science.gov (United States)

    Narsimhan, Karthik; Michaelis, Vladimir K; Mathies, Guinevere; Gunther, William R; Griffin, Robert G; Román-Leshkov, Yuriy

    2015-02-11

    The selective low temperature oxidation of methane is an attractive yet challenging pathway to convert abundant natural gas into value added chemicals. Copper-exchanged ZSM-5 and mordenite (MOR) zeolites have received attention due to their ability to oxidize methane into methanol using molecular oxygen. In this work, the conversion of methane into acetic acid is demonstrated using Cu-MOR by coupling oxidation with carbonylation reactions. The carbonylation reaction, known to occur predominantly in the 8-membered ring (8MR) pockets of MOR, is used as a site-specific probe to gain insight into important mechanistic differences existing between Cu-MOR and Cu-ZSM-5 during methane oxidation. For the tandem reaction sequence, Cu-MOR generated drastically higher amounts of acetic acid when compared to Cu-ZSM-5 (22 vs 4 μmol/g). Preferential titration with sodium showed a direct correlation between the number of acid sites in the 8MR pockets in MOR and acetic acid yield, indicating that methoxy species present in the MOR side pockets undergo carbonylation. Coupled spectroscopic and reactivity measurements were used to identify the genesis of the oxidation sites and to validate the migration of methoxy species from the oxidation site to the carbonylation site. Our results indicate that the Cu(II)-O-Cu(II) sites previously associated with methane oxidation in both Cu-MOR and Cu-ZSM-5 are oxidation active but carbonylation inactive. In turn, combined UV-vis and EPR spectroscopic studies showed that a novel Cu(2+) site is formed at Cu/Al <0.2 in MOR. These sites oxidize methane and promote the migration of the product to a Brønsted acid site in the 8MR to undergo carbonylation. PMID:25562431

  7. Chloride diffusion in partially saturated cementitious material

    DEFF Research Database (Denmark)

    Nielsen, Erik Pram; Geiker, Mette Rica

    2003-01-01

    The paper proposes a combined application of composite theory and Powers' model for microstructural development for the estimation of the diffusion coefficient as a function of the moisture content of a defect-free cementitious material. Measurements of chloride diffusion in mortar samples (440 kg....../m(3) rapid-hardening Portland cement, w/c = 0.5, maturity minimum 6 months) stored at 65% and 85% RH, as well as in vacuum-saturated mortar samples, illustrate the applicability of the method. (C) 2003 Elsevier Science Ltd. All rights reserved....

  8. Oral cadmium chloride intoxication in mice

    DEFF Research Database (Denmark)

    Andersen, O; Nielsen, J B; Svendsen, P

    1988-01-01

    Diethyldithiocarbamate (DDC) is known to alleviate acute toxicity due to injection of cadmium salts. However, when cadmium chloride was administered by the oral route, DDC enhanced rather than alleviated the acute toxicity; both oral and intraperitoneal (i.p.) administration of DDC had this effect....... Thus, orally administered DDC enhanced cadmium-induced duodenal and ileal tissue damage and inhibition of peristalsis, as indicated by an increased intestinal transit time. At low cadmium doses, the whole-body retention of cadmium was increased by oral DDC administration. Intraperitoneally administered...

  9. Interactions between chloride ingress and carbonation in cementitious materials

    OpenAIRE

    SAILLIO, Mickael; BARBERON, Fabien; BAROGHEL BOUNY, Véronique; GEGOUT, Philippe; PLATRET, Gérard; D'ESPINOSE DE LA CAILLERIE, JB

    2011-01-01

    Carbonation and chloride attacks are the major causes of reinforced concrete (RC) structure deterioration by initiation of steel rebar corrosion. These attacks are usually studied separately in the literature. Chloride-induced corrosion takes place mainly in marine environment or in the case of contact with deicing salts, while carbonation is systematically present in all RC structures at a variable degree. Since carbonation leads to significant microstructure changes, the effect of chloride ...

  10. Surface Chloride Concentration of Concrete under Shallow Immersion Conditions

    OpenAIRE

    Jun Liu; Kaifeng Tang; Dong Pan; Zongru Lei; Weilun Wang; Feng Xing

    2014-01-01

    Deposition of chloride ions in the surface layer of concrete is investigated in this study. In real concrete structure, chloride ions from the service environment can penetrate into concrete and deposit in the surface layer, to form the boundary condition for further diffusion towards the interior. The deposit amount of chloride ions in the surface layer is normally a function of time, rather than a constant. In the experimental investigation, concrete specimens with different mix proportions...

  11. Synthesis, X-ray Structure and Bioactivity of N-4-Methyl-1,2,3-thiadiazole-5-carbonyl-N'-3,5- dichloro-4-(1,1,2,2-tetrafluoroethoxyl)phenyl Urea%Synthesis, X-ray Structure and Bioactivity of N-4-Methyl-1,2,3-thiadiazole-5-carbonyl-N'-3,5- dichloro-4-(1,1,2,2-tetrafluoroethoxyl)phenyl Urea

    Institute of Scientific and Technical Information of China (English)

    GUO Dan-Dan; Bakulev V. Alekseevich; WANG Dun; FAN Zhi-Jin; LI Juan-Juan; SONG Hai-Bin; FAN Qian; Tatiana A. Kalinina; Morzherin Yury Yur'evich; Belskaya N. Pavlovna

    2012-01-01

    The title compound N-4-methyl-1,2,3-thiadiazole-5-carbonyl-N'-3,5-dichloro-4- (1,1,2,2- tetrafluoroethoxyl)phenyl urea (C13H8Cl2F4N4O3S, Mr = 447.19) has been synthesized from 4-methyl- 1,2,3-thiadiazole-5-carbonyl chloride as the starting material, and its structure was characterized by proton Nuclear Magnetic Resonance (1H NMR), Infra Red Spectroscopy (IR), high-resolution mass spectroscopy (HRMS), and single-crystal X-ray diffraction. The crystal of the title compound belongs to triclinic, space group Pi with a = 6.0780(8), b = 11.3760(14), c = 12.1440(18) A, α = 96.887(7), β = 91.027(12), γ= 104.252(13)°, Z = 2, V= 806.98(19)A3, Dc = 1.840 g/cm3, μ= 0.601 mm-1, F(000) = 448, R = 0.0450 and wR = 0.0869. X-ray analysis indicates that the 1,2,3-thiadiazole ring is not coplanar with the phenyl ring, and the dihedral angle is 33.57°. Two intermolecular hydrogen bonds N(2)-H…O(1 ), S(1 )…H-C(11), and three weak intermolecular interactions, C(11)…O(1), N(1)…O(2) and S…O(1), are observed. The bioassay results indicate that the title compound has good insecticidal activity against Culex pipiens pallens and good induction activity for tobacco against tobacco mosaic virus which is equal to that of TDL.

  12. N,N-Dimethyldehydroabietylammonium chloride ethanol monosolvate

    Directory of Open Access Journals (Sweden)

    Xiu-Zhi Huang

    2013-06-01

    Full Text Available The title compound {systematic name: 1-[(1R,4aS,10aR-7-isopropyl-1,4a-dimethyl-1,2,3,4,4a,9,10,10a-octahydrophenanthren-1-yl]-N,N-dimethylmethanaminium chloride ethanol monosolvate}, C22H36N+·Cl−·C2H6O, was synthesized from dehydroabietylamine by N-methylation with formaldehyde/formic acid and transformation into the hydrochloride. The dehydroabietyl moiety exhibits the usual conformation with the two cyclohexane rings in chair and half-chair conformations and a trans-ring junction. The crystal structure is built up from columns of the dehydroabietyl moieties stacked along the a axis. These columns are held together by the chloride ions via N—H...Cl and C—H...Cl interactions, which establish a two-dimensional network parallel to (010. The ethanol solvent molecules are located between the columns and anchored via O—H...Cl hydrogen bonds.

  13. Open cycle lithium chloride cooling system

    Science.gov (United States)

    Lenz, T. G.; Loef, G. O. G.; Iyer, R.; Wenger, J.

    1983-05-01

    A lithium chloride open cycle absorption chiller has been designed, built and tested. Solution reconcentration takes place in a small counter current packed column supplied with solar heated air. Removal of noncondensable gases that enter the chiller dissolved in the strong solution and the make-up refrigerant streams is accomplished by a liquid-jet ejector and a small vacuum pump. Cooling capacities approaching 1.4 tons and COP levels of 0.58 have been achieved at non-optimum operating conditions. Test results from preliminary system operation suggest that mass transfer processes in both the packed column reconcentrator and the absorber are controlled by concentration gradients in the lithium chloride solution. Liquid phase controlled mass transfer dictates an operating strategy different from the previously assumed gas phase controlled process to obtain maximum rates of evaporation in the packed column. Determination of optimal operating conditions leading to decreased electrical power consumption and improved cooling capacity and coefficient of performance will require further analysis and testing.

  14. Synthesis and structure characterization of diethyldiallylammonium chloride

    Institute of Scientific and Technical Information of China (English)

    刘立华; 龚竹青; 郑雅杰

    2003-01-01

    The unsaturated quaternary ammonium salt diethyldiallylammonium chloride(DEDAAC) was synthesized in a two-step synthetic method. The influences of the adding method of raw materials and temperature on the yields of diethylallylamine (DEAA), and drying and temperature on the synthesis of DEDAAC were investigated. The content of in-process product DEAA was determined by non-aqueous titration. The structure of product DEDAAC was identified with IR, 1 H NMR and elemental analysis. The results show that adding allyl chloride and sodium hydroxide alternately can increase the yield of DEAA and decrease by-products. In further synthesizing of DEDAAC from DEAA, the step of drying DEAA is very necessary. When DEAA is dried by solid sodium hydroxide, good columnar crystals with a high purity(mp 199.5-201.0 ℃) are obtained; when DEAA is undried or the content of water in DEAA is above 20%, only platelets with bad quality are obtained even without crystals. The suitable synthesis conditions for DEAA and DEDAAC are 35 ℃, 6 h and 40 ℃, 36 h, respectively, and their yields are 69.7% and 67.3%, respectively.

  15. Fault locator of an allyl chloride plant

    Directory of Open Access Journals (Sweden)

    Savković-Stevanović Jelenka B.

    2004-01-01

    Full Text Available Process safety analysis, which includes qualitative fault event identification, the relative frequency and event probability functions, as well as consequence analysis, was performed on an allye chloride plant. An event tree for fault diagnosis and cognitive reliability analysis, as well as a troubleshooting system, were developed. Fuzzy inductive reasoning illustrated the advantages compared to crisp inductive reasoning. A qualitative model forecast the future behavior of the system in the case of accident detection and then compared it with the actual measured data. A cognitive model including qualitative and quantitative information by fuzzy logic of the incident scenario was derived as a fault locator for an ally! chloride plant. The obtained results showed the successful application of cognitive dispersion modeling to process safety analysis. A fuzzy inductive reasoner illustrated good performance to discriminate between different types of malfunctions. This fault locator allowed risk analysis and the construction of a fault tolerant system. This study is the first report in the literature showing the cognitive reliability analysis method.

  16. Copper-catalyzed oxidative desulfurization-oxygenation of thiocarbonyl compounds using molecular oxygen: an efficient method for the preparation of oxygen isotopically labeled carbonyl compounds.

    Science.gov (United States)

    Shibahara, Fumitoshi; Suenami, Aiko; Yoshida, Atsunori; Murai, Toshiaki

    2007-06-21

    A novel copper-catalyzed oxidative desulfurization reaction of thiocarbonyl compounds, using molecular oxygen as an oxidant and leading to formation of carbonyl compounds, has been developed, and the utility of the process is demonstrated by its application to the preparation of a carbonyl-18O labeled sialic acid derivative. PMID:17844744

  17. Syntheses of fused tetrahydro--carboline analogues through imide carbonyl activation using BBr3: Evidence for the involvement of fused cyclic -acyliminium ion intermediate

    Indian Academy of Sciences (India)

    Selvaraj Mangalaraj; Jayaraman Selvakumar; Chinnasamy Ramaraj Ramanathan

    2015-05-01

    The fused cyclic -acyliminium ion generated during the imide carbonyl activation reaction of phenethylphthalimide was confirmed by single crystal X-ray diffraction. The Lewis acid assisted imide carbonyl activation methodology was successfully extended to synthesize fused tetrahydro--carboline units from the corresponding -indolylethylimides.

  18. Interpretation of postmortem vitreous concentrations of sodium and chloride.

    Science.gov (United States)

    Zilg, B; Alkass, K; Berg, S; Druid, H

    2016-06-01

    Vitreous fluid can be used to analyze sodium and chloride levels in deceased persons, but it remains unclear to what extent such results can be used to diagnose antemortem sodium or chloride imbalances. In this study we present vitreous sodium and chloride levels from more than 3000 cases. We show that vitreous sodium and chloride levels both decrease with approximately 2.2mmol/L per day after death. Since potassium is a well-established marker for postmortem interval (PMI) and easily can be analyzed along with sodium and chloride, we have correlated sodium and chloride levels with the potassium levels and present postmortem reference ranges relative the potassium levels. We found that virtually all cases outside the reference range show signs of antemortem hypo- or hypernatremia. Vitreous sodium or chloride levels can be the only means to diagnose cases of water or salt intoxication, beer potomania or dehydration. We further show that postmortem vitreous sodium and chloride strongly correlate and in practice can be used interchangeably if analysis of one of the ions fails. It has been suggested that vitreous sodium and chloride levels can be used to diagnose drowning or to distinguish saltwater from freshwater drowning. Our results show that in cases of freshwater drowning, vitreous sodium levels are decreased, but that this mainly is an effect of postmortem diffusion between the eye and surrounding water rather than due to the drowning process, since the decrease in sodium levels correlates with immersion time. PMID:27105154

  19. On Barium Oxide Solubility in Barium-Containing Chloride Melts

    Science.gov (United States)

    Nikolaeva, Elena V.; Zakiryanova, Irina D.; Bovet, Andrey L.; Korzun, Iraida V.

    2016-08-01

    Oxide solubility in chloride melts depends on temperature and composition of molten solvent. The solubility of barium oxide in the solvents with barium chloride content is essentially higher than that in molten alkali chlorides. Spectral data demonstrate the existence of oxychloride ionic groupings in such melts. This work presents the results of the BaO solubility in two molten BaCl2-NaCl systems with different barium chloride content. The received data together with earlier published results revealed the main regularities of BaO solubility in molten BaO-BaCl2-MCl systems.

  20. Catalytic Conversion of Cellulose to Levulinic Acid by Metal Chlorides

    Directory of Open Access Journals (Sweden)

    Beixiao Zhang

    2010-08-01

    Full Text Available The catalytic performance of various metal chlorides in the conversion of cellulose to levulinic acid in liquid water at high temperatures was investigated. The effects of reaction parameters on the yield of levulinic acid were also explored. The results showed that alkali and alkaline earth metal chlorides were not effective in conversion of cellulose, while transition metal chlorides, especially CrCl3, FeCl3 and CuCl2 and a group IIIA metal chloride (AlCl3, exhibited high catalytic activity. The catalytic performance was correlated with the acidity of the reaction system due to the addition of the metal chlorides, but more dependent on the type of metal chloride. Among those metal chlorides, chromium chloride was found to be exceptionally effective for the conversion of cellulose to levulinic acid, affording an optimum yield of 67 mol % after a reaction time of 180 min, at 200 °C, with a catalyst dosage of 0.02 M and substrate concentration of 50 wt %. Chromium metal, most of which was present in its oxide form in the solid sample and only a small part in solution as Cr3+ ion, can be easily separated from the resulting product mixture and recycled. Finally, a plausible reaction scheme for the chromium chloride catalyzed conversion of cellulose in water was proposed.

  1. Durability of cracked fibre reinforced concrete structures exposed to chlorides

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place; Ekman, Tom; Hansen, Kurt Kielsgaard

    1999-01-01

    is used as environmental load. The chloride penetration is characterized both qualitatively (UV-test) and quantitatively (chloride profile) and by microscopy. The test programme involves three different concrete qualities. Both steel fibres and polypropylene fibres are used in the concrete beams as well......Durability studies are carried out by subjecting FRC-beams to combined mechanical and environmental load. Mechanical load is obtained by exposing beams to 4-point bending until a predefined crack width is reached, using a newly developed test setup. Exposure to a concentrated chloride solution...... as main reinforcement. The effect of the cracks, the fibres and the concrete quality on the chloride penetration is studied....

  2. Fish Proteins as Targets of Ferrous-Catalyzed Oxidation: Identification of Protein Carbonyls by Fluorescent Labeling on Two-Dimensional Gels and MALDI-TOF/TOF Mass Spectrometry

    DEFF Research Database (Denmark)

    Pazos, Manuel; da Rocha, Angela Pereira; Roepstorff, Peter;

    2011-01-01

    , indicating that post-translational modifications may change the resistance of proteins to oxidative damage. The Fe(II)/ascorbate treatment significantly increased carbonylation of important structural proteins in fish muscle, mainly actin and myosin, and degradation products of those proteins were observed...... with fluorescein-5-thiosemicarbazide (FTSC) to tag carbonyl groups and separated by two-dimensional gel electrophoresis. Consecutive visualization of protein carbonyl levels by capturing the FTSC signal and total protein levels by capturing the SyproRuby staining signal allowed us to quantify the relative change...... in protein carbonyl levels corrected for changes in protein content. Proteins were identified using MALDI-TOF/TOF mass spectrometry and homology-based searches. The results show that freshly extracted cod muscle proteins exhibit a detectable carbonylation background and that the incubation with Fe...

  3. Carbonyl and oxalyl bridged bis(1,5-diaminotetrazole)-based energetic salts.

    Science.gov (United States)

    Joo, Young-Hyuk; Twamley, Brendan; Shreeve, Jean'ne M

    2009-09-14

    High density energetic salts containing nitrogen rich cations and carbonyl- or oxalylbis(diamino-tetrazole) anions, which were obtained from cyanogen azide and hydrazine, were readily synthesized. In every case, a new family of energetic salts 3-14 were characterized by vibrational spectroscopy, multinuclear ((1)H, (13)C, (15)N) NMR, elemental analyses, density, differential scanning calorimetry and impact sensitivity. Compound 12 was structured by single crystal X-ray diffraction. The densities of 3-14, determined by gas pycnometer, range between 1.500 and 1.676 g cm(-3). The heats of formation and detonation properties for these stable salts were calculated by using Gaussian 03 and Cheetah 5.0, respectively. PMID:19658135

  4. Temporal variation of carbonyl compound concentrations at a semi-rural site in Denmark

    DEFF Research Database (Denmark)

    Christensen, C.S.; Skov, H.; Nielsen, T.;

    2000-01-01

    The atmospheric concentrations of formaldehyde, acetaldehyde and acetone were measured by the DNPH-technique at the semi-rural site Lille Valby, Denmark (55 degrees N) between May-July 1995, The average concentrations were observed to be 1.2 ppbv for formaldehyde, 0.8 ppbv for acetaldehyde and 1.......9 ppbv for acetone, For the set of carbonyl compounds, concentrations were found to be highly correlated, though only during daytime, The weak correlations observed during nighttime are believed to be caused by the dry deposition of especially formaldehyde, During periods with low photochemical activity...... of hydrocarbons during long-range transport. Especially, the concentration levels of acetone showed a pronounced seasonal-variation with the highest levels observed during summertime and lowest in winter and spring. The seasonal variation in the concentration levels of formaldehyde and acetaldehyde were small...

  5. Magnetorheology of suspensions based on graphene oxide coated or added carbonyl iron microspheres and sunflower oil

    Science.gov (United States)

    Chen, Kaikai; Zhang, Wen Ling; Shan, Lei; Zhang, Xiangjun; Meng, Yonggang; Choi, Hyoung Jin; Tian, Yu

    2014-10-01

    Magnetorheological (MR) fluids based on carbonyl iron (CI) particles coated with graphene oxide (GO) and sunflower oils were studied and compared with MR fluids (MRFs) prepared with CI particles added with GO sheets. Adding GO sheets into CI had a negligible effect on the rheological properties of the MRF. Coating the spheres with GO markedly decreased the shear strength at high shear rates due to the remarkable lubricating function of the GO surface. Different behaviors were observed in the shear thickening phenomenon when the GO surface changed the mechanical interaction between particles. The results demonstrated the importance of the role of interparticle friction for MRF in shear mode and discussed the weak shear thickening phenomenon with fine lubricating coating layers and oils.

  6. Gold/Iron Carbonyl Clusters for Tailored Au/FeOx Supported Catalysts

    Directory of Open Access Journals (Sweden)

    Stefania Albonetti

    2011-12-01

    Full Text Available A novel preparation method was developed for the preparation of gold/iron oxide supported catalysts using the bimetallic carbonyl cluster salts [NEt4]4[Au4Fe4(CO16] and [NEt4][AuFe4(CO16] as precursors of highly dispersed nanoparticles over different supports. A series of catalysts with different metal loadings were prepared and tested in the complete oxidation of dichlorobenzene, toluene, methanol and in the preferential oxidation of CO in the presence of H2 (PROX as model reactions. The characterization by BET, XRD, TEM, H2-TPR, ICP-AES and XPS point out the way the nature of the precursors and the thermal treatment conditions affected the dispersion of the active phase and their catalytic activity in the studied reactions.

  7. A highly efficient procedure for the oxathioacetalization of carbonyl compounds under solvent-free conditions

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The novel efficient procedure has been developed for the oxathioacetalization of carbonyl compounds and 2-mercaptoethanol using the novel carbon-based sulfonic acid as catalyst under solvent-free condition at room temperature. The results showed that the novel catalyst was very efficient for the reactions with good to excellent yields in short time. The novel catalyst owned many advantages such as operational simplicity,without need of any solvent,small amount of usage,low cost of the catalyst used,high yields,applicability to large-scale reactions,reusability and chemoselectivity over the traditional catalysts,which made the catalyst one of the best choices for the reactions.

  8. Adiabatic mixed-field orientation of ground-state-selected carbonyl sulfide molecules

    CERN Document Server

    Kienitz, Jens S; Mullins, Terry; Długołęcki, Karol; González-Férez, Rosario; Küpper, Jochen

    2016-01-01

    We experimentally demonstrated strong adiabatic mixed-field orientation of carbonyl sulfide molecules (OCS) in their absolute ground state of $\\text{N}_{\\text{up}}/\\text{N}_{\\text{tot}}=0.882$. OCS was oriented in combined non-resonant laser and static electric fields inside a two-plate velocity map imaging spectrometer. The transition from non-adiabatic to adiabatic orientation for the rotational ground state was studied by varying the applied laser and static electric field. Above static electric field strengths of 10~kV/cm and laser intensities of $10^{11} \\text{W/cm}^2$ the observed degree of orientation reached a plateau. These results are in good agreement with computational solutions of the time-dependent Schr\\"odinger equation.

  9. Synthesis of Unsymmetric Ureas by Selenium-Catalyzed Oxidative-Reductive Carbonylation with CO

    Institute of Scientific and Technical Information of China (English)

    MEI Jian-Ting; LU Shi-Wei

    2003-01-01

    @@ Unsymmetric, substituted ureas that contain the peptide bond (NHCONH), many of which possess biological activities, are widely used as herbicides, agrochemicals and pharmaceuticals. [1,2] A series of unsymmetric ureascontaining substituted groups have been synthesized via selenium-catalyzed selective oxidative-reductive carbonylation of amines and nitro compounds with CO instead of phosgene in one-pot reaction. [3,4] These catalytic reactions are important from both synthetic and industrial points of view, because not only the reactions can be proceeded with high selectivity of higher than 99% towards desired unsymmetric ureas, but also there exists a phase-transfer process of the selenium catalyst in thereaction, so that the after-treatment of the catalysts and products from the reaction systems can be easily separated by simple phase separation.

  10. Hydrogen bonding of transition metal carbonyl complexes with perfluoro-tert-butanol

    International Nuclear Information System (INIS)

    OH...OC type H-bond formation under perfluoro-tert-butanol interaction with transition metal carbonyl π-complexes: CpM(CO)3 (Cp=η5-C5H5 and η5-Et5C5, M=Mn,Re), MezM(CO)3 (Mez=η6-Me3H3C6, M=Cr, Mo, W), (η5-C5H5)H(CO)2PR3 (R=Ph, i-Pr, M=Mn, Re) is studied at low temperatures in liquid xenon and at ∼20 deg C-in CCl4. For isostructural complexes CO group O atom basisity grows under the replacement of one of CO groups by a phosphyne ligand, alkyl substituent introduction into π-ring and under the transition from Mn to Re. M(CO)6 (M=Cr, Mo, W) hexacarbonyls do not form H-bond with perfluoro-tert-butanol

  11. Inactivation of cellular enzymes by carbonyls and protein-bound glycation/glycoxidation products

    DEFF Research Database (Denmark)

    Morgan, Philip E; Dean, Roger T; Davies, Michael Jonathan

    2002-01-01

    products. In this study, we have examined the effect of glucose and carbonyl compounds (methylglyoxal, glyoxal, glycolaldehyde, and hydroxyacetone), and glycation products arising from reaction of these materials with model proteins, on the activity of three key cellular enzymes: glyceraldehyde-3-phosphate...... dehydrogenase (GAPDH), glutathione reductase, and lactate dehydrogenase, both in isolation and in cell lysates. In contrast to glucose (1M, both fresh and aged for 8 weeks), which had no effect, marked inhibition of all three enzymes was observed with methylglyoxal and glyoxal. GAPDH was also inhibited...... by glycolaldehyde and hydroxyacetone. Incubation of these enzymes with proteins that had been preglycated with methylglyoxal, but not glucose, also resulted in significant time- and concentration-dependent inhibition with both isolated enzymes and cell lysates. This inhibition was not metal ion, oxygen, superoxide...

  12. Ionization of oriented carbonyl sulfide molecules by intense circularly polarized laser pulses

    DEFF Research Database (Denmark)

    Dimitrovski, Darko; Abu-Samha, Mahmoud; Madsen, Lars Bojer;

    2011-01-01

    We present combined experimental and theoretical results on strong-field ionization of oriented carbonyl sulfide molecules by circularly polarized laser pulses. The obtained molecular frame photoelectron angular distributions show pronounced asymmetries perpendicular to the direction of the......-dimensionally-oriented polar molecules, in particular asymmetries in the emission direction of the photoelectrons. In the following article [Phys. Rev. A 83, 023406 (2011)] the focus is to understand strong-field ionization from three-dimensionally-oriented asymmetric top molecules, in particular the suppression of electron...... molecular electric dipole moment. These findings are explained by a tunneling model invoking the laser-induced Stark shifts associated with the dipoles and polarizabilities of the molecule and its unrelaxed cation. The focus of the present article is to understand the strong-field ionization of one...

  13. Enhanced microwave absorbing properties and heat resistance of carbonyl iron by electroless plating Co

    Science.gov (United States)

    Wang, Hongyu; Zhu, Dongmei; Zhou, Wancheng; Luo, Fa

    2015-11-01

    Co coated carbonyl iron particles (Co (CI)) are fabricated through electroless plating method, and the electromagnetic microwave absorbing properties are investigated in the frequencies during 8.2-12.4 GHz. The complex permittivity of CI particles after electroless plating Co is higher than that of raw CI particles due to improvment of the polarization process. Furthermore, according to the XRD and TG results, the Co layer can enhance the heat resistance of CI particles. The bandwidth below -10 dB can reach 3.9 GHz for the Co(CI) absorbent. The results indicate that the electroless plating Co not only enhances the absorbing properties but also improves the heat resistance of CI.

  14. Carbonyl Diisocyanate CO(NCO)2: Synthesis and Structures in Solid State and Gas Phase.

    Science.gov (United States)

    Klapötke, Thomas M; Krumm, Burkhard; Rest, Sebastian; Scharf, Regina; Schwabedissen, Jan; Stammler, Hans-Georg; Mitzel, Norbert W

    2016-07-01

    A modified synthesis for carbonyl diisocyanate, CO(NCO)2, starting from trichloroisocyanuric acid and diphosgene is described. In addition to the previously reported (13)C NMR resonances, the (15)N NMR shift is determined for the first time. The structure in the solid state was determined by X-ray diffraction (XRD) on in situ grown crystals, that in the gas phase was experimentally determined by electron diffraction (GED) and for single molecules theoretically by quantum-chemical calculations. The structures are compared and discussed with related systems. Quantum-chemical calculations as well as GED and XRD prove syn-syn to be the conformation of lowest energy. In quantum-chemical calculations and GED the presence of a syn-anti conformer was confirmed and the structure of this conformer was determined.

  15. Investigation on peak frequency of the microwave absorption for carbonyl iron/epoxy resin composite

    Energy Technology Data Exchange (ETDEWEB)

    Wang Bochong; Wei Jianqiang; Yang Yong; Wang Tao [Institute of Applied Magnetics, Key Laboratory of Magnetism and Magnetic Materials of Ministry of Education, Lanzhou University, Lanzhou 730000 (China); Li Fashen, E-mail: lifs@lzu.edu.c [Institute of Applied Magnetics, Key Laboratory of Magnetism and Magnetic Materials of Ministry of Education, Lanzhou University, Lanzhou 730000 (China)

    2011-04-15

    Microwave absorbing characteristics of carbonyl iron/epoxy resin composite with various volume concentrations were investigated in 0.1-18 GHz. According to the electromagnetic parameters and thicknesses of the sample, numerical calculation and experiment have demonstrated that the frequency dependence of the microwave absorption comply with the quarter-wavelength ({lambda}/4) matching model that may explain not only the peak frequency but also the number of the peaks. It implies that the quarter-wavelength condition can be successfully applied to understand and predict the peak frequency of the microwave absorption for ferromagnetic metal-based composites. - Research highlights: > The dip in RL complies with the quarter-wavelength condition. > Two dips appear simultaneously when the sample thickness is thicker than the critical thickness t{sub c}{sup 3/4}. > The peak frequency of the dips can be manipulated by changing the sample thickness.

  16. Identification of the non-pertechnetate species in Hanford waste tanks, Tc(I) carbonyl complexes

    International Nuclear Information System (INIS)

    Immobilization of the high-level nuclear waste stored at the Hanford Reservation has been complicated by the presence of soluble, lower-valent technetium species. Previous work by Schroeder and Blanchard has shown that these species cannot be removed by ion-exchange and are difficult to oxidize. The Tc K-edge XANES spectra of the species in Tanks SY-101 and SY-103 were reported by Blanchard, but they could not be assigned to any known technetium complex. We report that the XANES spectra are most likely those of Tc(I)-carbonyl species, especially fac-Tc(CO)3(gluconate)2-. This is further supported by EXAFS and 99Tc-NMR studies in nonradioactive simulants of these tank wastes

  17. Formation and characterization of magnesium bisozonide and carbonyl complexes in solid argon.

    Science.gov (United States)

    Wang, Guanjun; Gong, Yu; Zhang, Qingqing; Zhou, Mingfei

    2010-10-14

    The reactions of magnesium atoms with dioxygen and dioxygen/carbon monoxide mixture have been investigated by matrix isolation infrared absorption spectroscopy. Magnesium atoms react with dioxygen in solid argon to form the inserted MgO(2) molecules under UV excitation, which were previously characterized. Annealing allows the dioxygen molecules to diffuse and to react with MgO(2) and form the magnesium bisozonide complex, Mg(O(3))(2), which is proposed to be coordinated by two argon atoms in solid argon matrix. The Mg(O(3))(2)(Ar)(2) complex is characterized to have two equivalent side-on bonded ozonide ligands with a D(2h) symmetry. The coordinated argon atoms can be replaced by carbon monoxide to give the magnesium bisozonide dicarbonyl complex, Mg(O(3))(2)(CO)(2), a neutral magnesium carbonyl complex with CO binding to the Mg(2+) center. PMID:20857987

  18. Study on Ni/C catalysts for vapor phase carbonylation of ethanol

    Institute of Scientific and Technical Information of China (English)

    Qing Zhang; Huifang Wang; Guosong Sun; Kelin Huang; Weiping Fang; Yiquan Yang

    2008-01-01

    Activated carbon-supported Ni catalysts for vapor phase carbonylation of ethanol to propionic acid in the presence of ethyl iodide as promoter were investigated. Under optimum reaction conditions, the conversions of carbon monoxide and ethanol were measured to be 81.4% and 98.4%, respectively, while the selectivity for propionic acid was found to be 98.65%. The catalyst was stable within 48 h on stream. XRD and XPS methods were used to characterize the structures and surface properties of the fresh and tested catalysts. The characterization results indicated that aggregation of nickel particles and formation of nickel iodide on the catalyst surface should be responsible for the deactivation of the catalysts.

  19. Formation and emissions of carbonyls during and following gas-phase ozonation of indoor materials

    DEFF Research Database (Denmark)

    Poppendieck, D.G.; Hubbard, H.F.; Weschler, Charles J.;

    2007-01-01

    Ozone concentrations that are several orders of magnitude greater than typical urban ambient concentrations are necessary for gas-phase ozonation of buildings, either for deodorization or for disinfection of biological agents. However, there is currently no published literature on the interaction...... of building materials and ozone under such extreme conditions. It would be useful to understand, for example in the case of building re-occupation planning, what types and amounts of reaction products may form and persist in a building after ozonation. In this study, 24 materials were exposed to ozone...... at concentrations of 1000 ppm in the inlet stream of experimental chambers. Fifteen target carbonyls were selected and measured as building ozonation by-products (BOBPs). During the 36 h that include the 16 h ozonation and 20 h persistence phase, the total BOBP mass released from flooring and wall coverings ranged...

  20. Protonation Sites, Tandem Mass Spectrometry and Computational Calculations of o-Carbonyl Carbazolequinone Derivatives

    Science.gov (United States)

    Martínez-Cifuentes, Maximiliano; Clavijo-Allancan, Graciela; Zuñiga-Hormazabal, Pamela; Aranda, Braulio; Barriga, Andrés; Weiss-López, Boris; Araya-Maturana, Ramiro

    2016-01-01

    A series of a new type of tetracyclic carbazolequinones incorporating a carbonyl group at the ortho position relative to the quinone moiety was synthesized and analyzed by tandem electrospray ionization mass spectrometry (ESI/MS-MS), using Collision-Induced Dissociation (CID) to dissociate the protonated species. Theoretical parameters such as molecular electrostatic potential (MEP), local Fukui functions and local Parr function for electrophilic attack as well as proton affinity (PA) and gas phase basicity (GB), were used to explain the preferred protonation sites. Transition states of some main fragmentation routes were obtained and the energies calculated at density functional theory (DFT) B3LYP level were compared with the obtained by ab initio quadratic configuration interaction with single and double excitation (QCISD). The results are in accordance with the observed distribution of ions. The nature of the substituents in the aromatic ring has a notable impact on the fragmentation routes of the molecules. PMID:27399676

  1. Synthesis of high refractive spiro heterocyclic derivatives through thioacetalization of multi-carbonyl compounds

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Jim Young; Maheswara, Muchchintala; Do, Jung Yun [Pusan National Univ., Busan (Korea, Republic of)

    2012-04-15

    Preparation of several new spirocyclic mercaptol derivatives is described. Thiol protection on multi-carbonyl compounds allows of high sulfur content necessary to induce high refractive index. Condensation of 1,3-dimercapto-2-propanol and cyclohexanone followed by successive oxidation and thioacetalization affords a dispiro cycle with four sulfurs. Selective S,S-protection of cyclohexane-1,4-dione is achieved with 1,3-dimercapto-2-propanol and 2,3-dimercapto-1-propanol to provide dispiro cycles with four sulfurs. Olefineoxidation of norbornene gives a useful dialdehyde intermediate which is transformed to 1,3-dithiolane for a linearly-bound-cyclic molecule. Refractive index of linearly-bound-cycles was below 1.60 and dispiro cycles exhibited high refractive index of 1.57-1.69.

  2. Magnetorheology of xanthan-gum-coated soft magnetic carbonyl iron microspheres and their polishing characteristics

    Science.gov (United States)

    Kwon, Seung Hyuk; Choi, Hyoung Jin; Lee, Jung Won; Hong, Kwang Pyo; Cho, Myeong Woo

    2013-06-01

    Magnetorheological (MR) fluids are colloidal suspensions of soft magnetic particles dispersed in a non-magnetic liquid. Among their applications, MR polishing has attracted considerable attention owing to its smart control of the polishing characteristics for dedicated microelectromechanical system applications. To improve the polishing characteristics of MR fluids, we fabricated carbonyl iron (CI) microspheres coated with xanthan gum (XG) by using a solvent casting method. The morphologies and densities of both pure CI and CI/XG particles were characterized using a scanning electron microscope and a pycnometer, respectively. In addition, the rheological characteristics of the MR fluids under various applied magnetic field strengths were examined using a rotational rheometer. The MR polishing characteristics were conducted using an MR polishing machine to examine the surface roughness and the material removal by MR polishing with added nano-ceria slurry abrasives.

  3. Major differences between the binuclear manganese boronyl carbonyl Mn2(BO)2(CO)9 and its isoelectronic chromium carbonyl analogue Cr2(CO)11.

    Science.gov (United States)

    Chang, Yu; Li, Qian-Shu; Xie, Yaoming; King, R Bruce

    2013-03-14

    The lowest energy structures of the manganese boronyl carbonyl Mn2(BO)2(CO)9 by more than 8 kcal/mol are found to have a single end-to-end bridging BO group bonding to one manganese atom through its boron atom and to the other manganese atom through its oxygen atom. The long Mn···Mn distances in these structures indicate the lack of direct manganese-manganese bonding as confirmed by essentially zero Wiberg bond indices. These Mn2(BO)2(CO)9 structures are favored thermochemically by more than 25 kcal/mol over dissociation into mononuclear fragments and thus appear to be viable synthetic objectives. This contrasts with the isoelectronic Cr2(CO)11 system, which is predicted to be disfavored relative to the mononuclear fragments Cr(CO)6 + Cr(CO)5. Analogous Mn2(BO)2(CO)9 structures with an end-to-end bridging CO group lie ∼17 kcal/mol in energy above the corresponding structures with end-to-end bridging BO groups. The lowest energy Mn2(BO)2(CO)9 structures without an end-to-end bridging BO group provide unprecedented examples of the coupling of two terminal BO groups to form a terminal dioxodiborene (B2O2) ligand with a B-B distance of ∼1.9 Å. Still higher energy Mn2(BO)2(CO)9 structures include singly bridged and doubly semibridged structures analogous to the previously optimized lowest energy Cr2(CO)11 structures. PMID:23402266

  4. The serum protein carbonyl content level in relation to exercise stress test

    Directory of Open Access Journals (Sweden)

    Titiporn Mekrungruangwong

    2012-01-01

    Full Text Available Background: Protein carbonyl (P is oxidatively-modified protein with diagnostic potential for acute myocardial infarction. However, many findings indicated the elevation of serum PC content level related to exercise, which could cause false positive results and limiting the specificity for acute coronary syndrome diagnosis. This study aims to evaluate the level of serum protein carbonyl content in healthy volunteers subjected to exercise stress test (EST. Materials and Methods: Serum from healthy volunteers was collected 5-10 min before performing EST and 1 hour after the EST was achieved. The serum was collected, and the serum PC content level was determined by spectrophotometric DNPH assay. Results: The serum PC content level after exercise stress test was significantly higher than that of before performing EST (0.373 ± 0.05 nM/mg vs. 0.275 ± 0.02 nM/mg, P < 0.0001. The results demonstrated that in both male and female, serum PC content level after EST was significantly higher than that of before performing EST (0.29 ± 0.03 nM/mg vs. 0.36 ± 0.05 nM/mg P < 0.0001 in male, 0.27 ± 0.02 nM/mg vs. 0.38 ± 0.06 nM/mg P < 0.0001 in female, respectively. Conclusions: This study demonstrated that exercise stress test could result in non-specificity and false positive increasing in serum PC content level in healthy subjects, which may cause misinterpretation when using PC as cardiac marker, especially in patients, who underwent exercise stress test or patients who performing heavy physical activities.

  5. Chitosan Prevents Gentamicin-Induced Nephrotoxicity via a Carbonyl Stress-Dependent Pathway

    Directory of Open Access Journals (Sweden)

    Chu-Kung Chou

    2015-01-01

    Full Text Available Aminoglycosides are widely used to treat infections; however, their applications are limited by nephrotoxicity. With the increase of antibiotic resistance, the use of aminoglycosides is inevitable. Low-molecular-weight chitosan (LMWC has shown renal protective effects in dialysis patients. However, no study has evaluated LMWC for preventing aminoglycoside-induced nephrotoxicity or determined the mechanisms underlying the renal protective effects. In this study, LMWC (165 or 825 mg/kg/day or metformin (100 mg/kg/day was orally administered for 13 days to rats with nephropathy induced by gentamicin (GM, a kind of aminoglycoside (150 mg/kg/day i.p. for 6 days. Both LMCW doses improved renal function. Serum creatinine levels improved in rats treated with 165 and 825 mg/kg/day LMWC (from 2.14 ± 0.74 mg/dL to 1.26 ± 0.46 mg/dL and 0.69 ± 0.12 mg/dL, resp., P < 0.05. Blood urea nitrogen levels were also improved in these rats (from 73.73 ± 21.13 mg/dL to 58.70 ± 22.71 mg/dL and 28.82 ± 3.84 mg/dL, resp., P < 0.05. Additionally, renal tissue morphology improved after LMWC treatment, and accumulation of renal methylglyoxal, a damage factor associated with carbonyl stress, was reversed. These results show that LMWC prevents GM-induced renal toxicity via a carbonyl stress-dependent pathway.

  6. Role of carbonyls and aromatics in the formation of tropospheric ozone in Rio de Janeiro, Brazil.

    Science.gov (United States)

    da Silva, Débora Bonfim Neves; Martins, Eduardo Monteiro; Corrêa, Sergio Machado

    2016-05-01

    The ozone in Rio de Janeiro has been in violation of national air quality standards. Among all of the monitoring stations, the Bangu neighbourhood has the most violations of the national standard of 160 μg m(-3) for the years 2012 and 2013. This study evaluated the reactivity of the carbonyls and aromatics in the tropospheric ozone formation processes. The samples were collected between July and October of 2013. Carbonyls were sampled using SiO2 cartridges coated with C18 and impregnated with 2,4-dinitrophenylhydrazine and were analysed by HPLC. Activated carbon cartridges and GC/MS were used to measure the concentration of monoaromatic hydrocarbons. An air quality monitoring station provided the concentrations of the criteria pollutants and the meteorological parameters. Cluster analysis and a Pearson correlation matrix were used to determine the formation of groups and the correlation of the variables. The evaluation of the volatile organic compounds (VOC) reaction with OH radicals and the MIR scale was used to extrapolate the reactivity of VOCs to the ozone formation. The average concentrations obtained were 19.7 and 51.9 μg m(-3) for formaldehyde and acetaldehyde, respectively. The mean concentrations obtained for aromatics were 1.5, 6.7, 1.5, 2.6 and 1.6 μg m(-3) for benzene, toluene, ethyl benzene, m+p-xylene and o-xylene, respectively. The cluster analysis indicated the presence of three similar groups, with one formed by gaseous criteria pollutants, another formed by the meteorological parameters, ozone and fine particles, and the last group formed by the aromatics. For the two reactivity scales evaluated, acetaldehyde and toluene were the main ozone precursors.

  7. Computational study of the carbonyl-ene reaction of encapsulated formaldehyde in Na-FAU zeolite

    Science.gov (United States)

    Sangthong, Winyoo; Probst, Michael; Limtrakul, Jumras

    2005-06-01

    Density-functional theory (B3LYP/6-31G(d,p)) and the ONIOM (Our-own-N-layer Integrated molecular Orbital+molecular Mechanics) approach utilizing two-layer ONIOM schemes (B3LYP/6-31G(d,p):UFF) have been employed to investigate structures of Na-exchanged zeolite-encapsulated formaldehyde (HCHO@Na-zeolite) and their interactions with propylene. The carbonyl-ene reaction of propylene and formaldehyde was studied on three model systems: (1) formaldehyde in Na-exchanged zeolite: HCHO@Na-zeolite/CH 3CH dbnd6 CH 2; (2) naked Na(I) as catalyst: Na(I)/HCHO/CH 3CH dbnd6 CH 2; (3) a bare model where only the reactants are present: HCHO/CH 3CH dbnd6 CH 2. It is found that inclusion of the extended zeolite framework has an effect on the structure and energetics of the adsorption complexes and leads to a lower energy barrier (25.1 kcal/mol) of the reaction as compared to the bare model system (34.4 kcal/mol). If the naked Na(I) interacts with the HCHO/CH 3CH dbnd6 CH 2 complex the energy barrier of the system is even lower than HCHO@Na-zeolite/CH 3CH dbnd6 CH 2, due to the large electrostatic field generated by the naked Na(I) cation (17.5 kcal/mol). The carbonyl-ene reaction of propylene using HCHO@Na-faujasite takes place in a single concerted reaction step.

  8. Ruthenium supported on magnetic nanoparticles: An efficient and recoverable catalyst for hydrogenation of alkynes and transfer hydrogenation of carbonyl compounds

    Science.gov (United States)

    Ruthenium supported on surface modified magnetic nanoparticles (NiFe2O4) has been successfully synthesized and applied for hydrogenation of alkynes at room temperature as well as transfer hydrogenation of a number of carbonyl compounds under microwave irradiation conditions. The ...

  9. Unusual Reaction of β-Hydroxy α-Diazo Carbonyl Compounds with Trichloroacetonitrile (CI3CCN) and Sodium Hydride

    Institute of Scientific and Technical Information of China (English)

    SHI Wei-Feng; JIANG Nan; WANG Jian-Bo

    2003-01-01

    @@ In the process of preparing α-diazo carbonyl compound 2 by imidation of 1, we unexpectedly observed a direct conversion of the hydroxyl group into trichloroacetylamino group. In this presentation, we report this unprecedented reaction, as well as the Rh2(OAc)4-catalyzed reaction of the resulting β-(trichloroacetyl)amino β-diazo carbonylcompounds 3. [ 1

  10. [Defects in TOR regulatory complexes retard aging and carbonyl/oxidative stress development in yeast Saccharomyces cerevisiae].

    Science.gov (United States)

    Homza, B V; Vasyl'kovs'ka, R A; Semchyshyn, H M

    2014-01-01

    TOR signaling pathway first described in yeast S. cerevisiae is the highly conserved regulator of eukaryotic cell growth, aging and stress resistance. The effect of nitrogen sources, in particular amino acids, on the activity of TOR signaling pathway is well studied, however its relation to carbohydrates is poor understood. The aim of the present study is expanding of our understanding of potential role of TOR regulatory complexes in development of carbonyl/oxidative stress that can result from yeast cultivation on glucose and fructose. It has been shown that the level of alpha-dicarbonyl compounds and protein carbonyl groups increased with time of yeast cultivation and was higher in cells grown on fructose that demonstrated their accelerated aging and carbonyl/oxidative stress development as compared with cells grown on glucose. The strains defective in TOR proteins cultivated in the presence of glucose as well as fructose demonstrated lower markers of the stress and aging than parental strain. Thus these data confirmed the previous conclusion on fructose more potent ability to cause carbonyl/oxidative stress and accelerated aging in S. cerevisiae as compared with glucose. However, defects in TOR regulatory complexes retard aging and development of the stress in yeast independent on the type of carbohydrate in the cultivation medium. PMID:24834721

  11. Determination and Comparison of Carbonyl Stretching Frequency of a Ketone in Its Ground State and the First Electronic Excited State

    Science.gov (United States)

    Bandyopadhyay, Subhajit; Roy, Saswata

    2014-01-01

    This paper describes an inexpensive experiment to determine the carbonyl stretching frequency of an organic keto compound in its ground state and first electronic excited state. The experiment is simple to execute, clarifies some of the fundamental concepts of spectroscopy, and is appropriate for a basic spectroscopy laboratory course. The…

  12. Photoelectron velocity-map imaging and theoretical studies of heteronuclear metal carbonyls MNi(CO)3- (M = Mg, Ca, Al)

    Science.gov (United States)

    Xie, Hua; Zou, Jinghan; Yuan, Qinqin; Fan, Hongjun; Tang, Zichao; Jiang, Ling

    2016-03-01

    The heteronuclear metal carbonyl anions MNi(CO)3- (M = Mg, Ca, Al) have been investigated using photoelectron velocity-map imaging spectroscopy. Electron affinities of neutral MNi(CO)3 (M = Mg, Ca, Al) are measured from the photoelectron spectra to be 1.064 ± 0.063, 1.050 ± 0.064, and 1.541 ± 0.040 eV, respectively. The C-O stretching mode in these three clusters is observed and the vibrational frequency is determined to be 2049, 2000, and 2041 cm-1 for MgNi(CO)3, CaNi(CO)3, and AlNi(CO)3, respectively. Density functional theory calculations are carried out to elucidate the geometric and electronic structures and to aid the experimental assignments. It has been found that three terminal carbonyls are preferentially bonded to the nickel atom in these heterobinuclear nickel carbonyls MNi(CO)3-1/0, resulting in the formation of the Ni(CO)3 motif. Ni remains the 18-electron configuration for MgNi(CO)3 and CaNi(CO)3 neutrals, but not for AlNi(CO)3. This is different from the homobinuclear nickel carbonyl Ni-Ni(CO)3 with the involvement of three bridging ligands. Present findings would be helpful for understanding CO adsorption on alloy surfaces.

  13. Double Conjugate Addition of Dithiols to Propargylic Carbonyl Systems To Generate Protected 1,3-Dicarbonyl Compounds

    NARCIS (Netherlands)

    Sneddon, Helen F.; Heuvel, Alexandra van den; Hirsch, Anna K.H.; Booth, Richard A.; Shaw, David M.; Gaunt, Matthew J.; Ley, Steven V.

    2006-01-01

    The work describes the efficient double conjugate addition of ethane and propane dithiols in the presence of sodium methoxide to a wide variety of propargylic carbonyl containing compounds. The products of these reactions are differentiated, 1,3-dicarbonyl systems useful for various synthesis progra

  14. THE MIXTURES OF 2.4-DINITROPHENYLHIDRAZONES OF INFERIOR CARBONYL COMPOUNDS AND THEIR HPLC SEPARATION WITH GRADIENT BINARY MIXTURES PHASES

    Directory of Open Access Journals (Sweden)

    Gheorghe Zgherea

    2008-06-01

    Full Text Available Mixtures of small quantities of carbonyl compounds are presents in foods, concerning sensorial qualities. The inferior carbonyl compounds (C2-C4, boiling point <100°C – mono and dicarbonyl – can be identified and measured their concentrations, after a separation by distillation on the water bath. They are transferred in a strongly acid solution of 2.4-dinitrophenylhidrazine (2.4-DNPH, generating a mixture of insoluble 2.4-dinitrophenylhidrazones (2.4-DNPH-ones. The 2.4-DNPH-ones are organic compounds with weak polarity, solids, crystallized, yellows and water insoluble, soluble in organic solvents. The mixture of 2.4dinitrophenylhidrazones may be separated by liquid chromatography, using the reverse phase mechanism [1-3]. This paper contains experimental and theoretical considerations to the means of separation through liquid chromatography of two synthetically and a natural mixtures that contain 2.4-DNPH-ones provided by inferior carbonyl compounds; to obtain conclude results, in the synthetically mixtures was introduce and 2.4-DNPH-ones provided by carbonyl compounds having three (acetone and propanal and four (isobutyl aldehyde atoms of carbon.

  15. Iodine-catalyzed addition of 2-mercaptoethanol to chalcone derivatives: Synthesis of the novel β-mercapto carbonyl compounds

    OpenAIRE

    Gürkan Yerli; Hayreddin Gezegen; Mustafa Ceylan

    2012-01-01

    In this study, a series of novel β-mercapto carbonyl derivatives (3-(2-hydroxyethylthio)-1,3-diarylpropan-1-one) (5a-i) were prepared by addition of 2-mercaptoethanol (4) to chalcones (3a-i) in the presence of catalytic amount of iodine (10 mol %) in CH 2Cl 2.

  16. Iodine-catalyzed addition of 2-mercaptoethanol to chalcone derivatives: Synthesis of the novel β-mercapto carbonyl compounds

    Directory of Open Access Journals (Sweden)

    Gürkan Yerli

    2012-01-01

    Full Text Available In this study, a series of novel β-mercapto carbonyl derivatives (3-(2-hydroxyethylthio-1,3-diarylpropan-1-one (5a-i were prepared by addition of 2-mercaptoethanol (4 to chalcones (3a-i in the presence of catalytic amount of iodine (10 mol % in CH 2Cl 2.

  17. Isotope effect in the carbonyl sulfide reaction with O(3P)

    DEFF Research Database (Denmark)

    Hattori, Shohei; Schmidt, Johan Albrecht; Mahler, Denise W.;

    2012-01-01

    The sulfur kinetic isotope effect (KIE) in the reaction of carbonyl sulfide (OCS) with O((3)P) was studied in relative rate experiments at 298 ± 2 K and 955 ± 10 mbar. The reaction was carried out in a photochemical reactor using long path FTIR detection, and data were analyzed using a nonlinear...

  18. Synthesis and preclinical evaluation of [11C-carbonyl]PF-04457845 for neuroimaging of fatty acid amide hydrolase

    International Nuclear Information System (INIS)

    Introduction: Fatty acid amide hydrolase (FAAH) has a significant role in regulating endocannabinoid signaling in the central nervous system. As such, FAAH inhibitors are being actively sought for pain, addiction, and other indications. This has led to the recent pursuit of positron emission tomography (PET) radiotracers targeting FAAH. We report herein the preparation and preclinical evaluation of [11C-carbonyl]PF-04457845, an isotopologue of the potent irreversible FAAH inhibitor. Methods: PF-04457845 was radiolabeled at the carbonyl position via automated [11C]CO2-fixation. Ex vivo brain biodistribution of [11C-carbonyl]PF-04457845 was carried out in conscious rats. Specificity was determined by pre-administration of PF-04457845 or URB597 prior to [11C-carbonyl]PF-04457845. In a separate experiment, rats injected with the title radiotracer had whole brains excised, homogenized and extracted to examine irreversible binding to brain parenchyma. Results: The title compound was prepared in 5 ± 1% (n = 4) isolated radiochemical yield based on starting [11C]CO2 (decay uncorrected) within 25 min from end-of-bombardment in > 98% radiochemical purity and a specific activity of 73.5 ± 8.2 GBq/μmol at end-of-synthesis. Uptake of [11C-carbonyl]PF-04457845 into the rat brain was high (range of 1.2–4.4 SUV), heterogeneous, and in accordance with reported FAAH distribution. Saturable binding was demonstrated by a dose-dependent reduction in brain radioactivity uptake following pre-treatment with PF-04457845. Pre-treatment with the prototypical FAAH inhibitor, URB597, reduced the brain radiotracer uptake in all regions by 71–81%, demonstrating specificity for FAAH. The binding of [11C-carbonyl]PF-04457845 to FAAH at 40 min post injection was irreversible as 98% of the radioactivity in the brain could not be extracted. Conclusions: [11C-carbonyl]PF-04457845 was rapidly synthesized via an automated radiosynthesis. Ex vivo biodistribution studies in conscious rodents

  19. [Survey of plasticizers in polyvinyl chloride toys].

    Science.gov (United States)

    Abe, Yutaka; Yamaguchi, Miku; Mutsuga, Motoh; Hirahara, Yoshichika; Kawamura, Yoko

    2012-01-01

    Plasticizers in 101 samples of polyvinyl chloride (PVC) toys on the Japanese market were surveyed. No phthalates were detected in designated toys, though bis(2-ethylhexyl)phthalate, diisononyl phthalate, diisobutyl phthalate, dibutyl phthalate, diisodecyl phthalate and benzyl butyl phthalate were detected in more than half of other toys. 2,2,4-Tributyl-1,3-pentanediol diisobutylate, o-acetyl tributyl citrate, adipates and diacetyl lauroyl glycerol, which are alternative plasticizers to phthalates, were detected. The results of structural analysis confirmed the presence of di(2-ethylhexyl)terephthalate, tributyl citrate, diisononyl 1,2-cyclohexanedicarboxylate and neopentyl glycol esters; these have not previonsly been reported in Japan. There appears to be a shift in plasticizers used for designated toys from phthalates to new plasticizers, and the number of different plasticizers is increasing.

  20. Estimating the chloride transport in cement paste

    Directory of Open Access Journals (Sweden)

    Princigallo, A.

    2012-06-01

    Full Text Available A method was developed to measure the diffusion coefficient of chloride ions in cement paste based on an analytical solution to Fick’s 2nd law in a cylindrical coordinate system. This natural method yielded diffusivity results within as little as a month. Testing time was reduced by exploiting the three-dimensional inward flux in the specimen. In an attempt to determine the saturation concentration, dense portland cement pastes were exposed to a concentrated chloride solution. The method proved to be useful for exploring cement hydration-induced changes in the diffusion coefficient of cement paste.

    Se ha desarrollado un método para medir el coeficiente de difusión de los iones cloruro en la pasta de cemento, partiendo de una aplicación analítica de la segunda ley de Fick en un sistema de coordinadas cilíndrico. Este método, que es natural, demostró ser capaz de producir resultados de difusividad en tan solo un mes. Se consiguió reducir el tiempo de ensayo mediante el aprovechamiento de la tridimensionalidad del flujo desde el exterior al interior de la probeta. A fin de determinar la concentración de saturación, se sometieron las pastas de cemento Portland a una disolución de cloruros concentrada. Este método resultó ser útil en el estudio de los cambios del coeficiente de difusión de la pasta de cemento provocados por las reacciones de hidratación que tienen lugar en esta.

  1. Protein carbonylation and water-holding capacity of pork subjected to frozen storage: effect of muscle type, premincing, and packaging.

    Science.gov (United States)

    Estévez, Mario; Ventanas, Sonia; Heinonen, Marina; Puolanne, Eero

    2011-05-25

    The present work aimed to study the relationship between protein carbonylation and the loss of water-holding capacity (WHC) occurring during frozen storage of porcine muscles. Pork samples corresponding to two different muscle types, glycolytic M. longissimus dorsi (LD) and oxidative M. psoas major (PM), and subjected to two different premincing, minced (MINCED) and intact pork pieces (INTACT), and packaging, vacuum packaged (VACUUM) and packed in oxygen-permeable bags (OXYGEN), procedures were frozen (-18 °C/12 weeks) and analyzed at sampling times upon thawing (weeks 1, 4, 8, and 12) for the relative amount of specific protein carbonyls, α-aminoadipic and γ-glutamic semialdehydes (AAS and GGS, respectively), and their ability to hold water using two different techniques. The formation of protein carbonyls occurred concomitantly with the loss of WHC, and both phenomena were found to be more intense in LD muscles and in MINCED and OXYGEN pork samples. The loss in WHC was from ca. 10 to 30% in 12 weeks, depending on the method of determination. Plausible mechanisms by which protein carbonylation may decrease the WHC of pork samples are thoroughly discussed in the present paper. Besides the likely impact of protein carbonylation in the water-myofibrillar protein relationships, the implication of AAS and GGS in further reactions including plausible cross-linking would explain the decrease of these semialdehydes by the end of frozen storage and would reinforce their liability in the loss of WHC of porcine muscles. The exact nature of these reactions, however, should be investigated in further studies.

  2. Carbonyl compound emissions from a heavy-duty diesel engine fueled with diesel fuel and ethanol-diesel blend.

    Science.gov (United States)

    Song, Chonglin; Zhao, Zhuang; Lv, Gang; Song, Jinou; Liu, Lidong; Zhao, Ruifen

    2010-05-01

    This paper presents an investigation of the carbonyl emissions from a direct injection heavy-duty diesel engine fueled with pure diesel fuel (DF) and blended fuel containing 15% by volume of ethanol (E/DF). The tests have been conducted under steady-state operating conditions at 1200, 1800, 2600 rpm and idle speed. The experimental results show that acetaldehyde is the most predominant carbonyl, followed by formaldehyde, acrolein, acetone, propionaldehyde and crotonaldehyde, produced from both fuels. The emission factors of total carbonyls vary in the range 13.8-295.9 mg(kWh)(-1) for DF and 17.8-380.2mg(kWh)(-1) for E/DF, respectively. The introduction of ethanol into diesel fuel results in a decrease in acrolein emissions, while the other carbonyls show general increases: at low engine speed (1200 rpm), 0-55% for formaldehyde, 4-44% for acetaldehyde, 38-224% for acetone, and 5-52% for crotonaldehyde; at medium engine speed (1800 rpm), 106-413% for formaldehyde, 4-143% for acetaldehyde, 74-113% for acetone, 114-1216% for propionaldehyde, and 15-163% for crotonaldehyde; at high engine speed (2600 rpm), 36-431% for formaldehyde, 18-61% for acetaldehyde, 22-241% for acetone, and 6-61% for propionaldehyde. A gradual reduction in the brake specific emissions of each carbonyl compound from both fuels is observed with increase in engine load. Among three levels of engine speed employed, both DF and E/DF emit most CBC emissions at high engine speed. On the whole, the presence of ethanol in diesel fuel leads to an increase in aldehyde emissions.

  3. Experimental and numerical investigation of chloride ingress in cracked concrete

    NARCIS (Netherlands)

    Šavija, B.

    2014-01-01

    Chloride induced corrosion of reinforcing steel is recognized as the most common deterioration mechanism affecting reinforced concrete structures. As such, it has been in focus of research for more than thirty years. Numerous studies of chloride ingress, corrosion initiation, and corrosion propagati

  4. Hydrophobic treatment of concrete as protection against chloride penetration

    NARCIS (Netherlands)

    Vries, J. de; Polder, R.B.; Borsje, H.

    1996-01-01

    Hydrophobic treatment makes a concrete surface absorb less water and less chloride. Hydrophobic treatment was studied as a protection agninst chloride penetration from deicing salts. Test methods were designed. Nine hydrophobic products were tested, of which three complied to the requirements on fin

  5. Microwave Mapping Demonstration Using the Thermochromic Cobalt Chloride Equilibrium

    Science.gov (United States)

    Nguyen, Vu D.; Birdwhistell, Kurt R.

    2014-01-01

    An update to the thermochromic cobalt(II) chloride equilibrium demonstration is described. Filter paper that has been saturated with aqueous cobalt(II) chloride is heated for seconds in a microwave oven, producing a color change. The resulting pink and blue map is used to colorfully demonstrate Le Châtelier's principle and to illuminate the…

  6. Local impermeant anions establish the neuronal chloride concentration

    DEFF Research Database (Denmark)

    Glykys, J; Dzhala, V; Egawa, K;

    2014-01-01

    Neuronal intracellular chloride concentration [Cl(-)](i) is an important determinant of γ-aminobutyric acid type A (GABA(A)) receptor (GABA(A)R)-mediated inhibition and cytoplasmic volume regulation. Equilibrative cation-chloride cotransporters (CCCs) move Cl(-) across the membrane, but accumulat...

  7. Chlorides behavior in raw fly ash washing experiments

    International Nuclear Information System (INIS)

    Chloride in fly ash from municipal solid waste incinerators (MSWIs) is one of the obstructive substances in recycling fly ash as building materials. As a result, we have to understand the behavior of chlorides in recycling process, such as washing. In this study, we used X-ray absorption near edge structure (XANES) and X-ray diffraction (XRD) to study the chloride behavior in washed residue of raw fly ash (RFA). We found that a combination of XRD and XANES, which is to use XRD to identify the situation of some compounds first and then process XANES data, was an effective way to explain the chlorides behavior in washing process. Approximately 15% of the chlorine in RFA was in the form of NaCl, 10% was in the form of KCl, 51% was CaCl2, and the remainder was in the form of Friedel's salt. In washing experiments not only the mole percentage but also the amount of soluble chlorides including NaCl, KCl and CaCl2 decreases quickly with the increase of liquid to solid (L/S) ratio or washing frequency. However, those of insoluble chlorides decrease slower. Moreover, Friedel's salt and its related compound (11CaO.7Al2O3.CaCl2) were reliable standards for the insoluble chlorides in RFA, which are strongly related to CaCl2. Washing of RFA promoted the release of insoluble chlorides, most of which were in the form of CaCl2.

  8. Phosphatase inhibitors activate normal and defective CFTR chloride channels.

    OpenAIRE

    Becq, F; Jensen, T J; Chang, X B; Savoia, A.; Rommens, J M; Tsui, L C; Buchwald, M; Riordan, J R; Hanrahan, J W

    1994-01-01

    The cystic fibrosis transmembrane conductance regulator (CFTR) chloride channel is regulated by phosphorylation and dephosphorylation at multiple sites. Although activation by protein kinases has been studied in some detail, the dephosphorylation step has received little attention. This report examines the mechanisms responsible for the dephosphorylation and spontaneous deactivation ("rundown") of CFTR chloride channels excised from transfected Chinese hamster ovary (CHO) and human airway epi...

  9. Monte Carlo calculation of chloride diffusion in concrete

    International Nuclear Information System (INIS)

    Coefficient of chloride diffusion is calculated by applying the Fick's second law of diffusion to a chloride concentration profile. Then from the signal strength for various chlorine gamma-ray energies was then calculated at the detector of the portable D-D neutron generator based PGNAA setup. (author)

  10. 21 CFR 172.165 - Quaternary ammonium chloride combination.

    Science.gov (United States)

    2010-04-01

    ... HUMAN CONSUMPTION Food Preservatives § 172.165 Quaternary ammonium chloride combination. The food... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Quaternary ammonium chloride combination. 172.165 Section 172.165 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

  11. Contribution on creep polygonization study in crystals. Creep of single crystalline silver chloride and sodium chloride

    International Nuclear Information System (INIS)

    Subgrain formation and their influence on plastic behavior of materials has been studied in the case of single crystals of silver chloride and sodium chloride crept at high temperature (T > 0.5 Tmelting). It is shown that the creep rate ε is a function of the mean subgrain diameter d. For secondary creep ε ∝ dk with k = 2 for NaCl and AgCl. During secondary creep, the substructure changes continuously: sub-boundaries migrate and sub-grains rotate. We find that sub-boundaries migration accounts for 35 pc of the total strain and that subgrain misorientation θ increases linearly with strain ε: θ ∝ 0.14 ε. The stability of permanent creep seems related to the power that the substructure is able to dissipate. The possible subgrain formation mechanisms are examined. It is shown that subgrain formation is closely related to the geometrical conditions of deformation and to the heterogeneities of this later. (author)

  12. Behavior and products of mechano-chemical dechlorination of polyvinyl chloride and poly (vinylidene chloride).

    Science.gov (United States)

    Xiao, Xiao; Zeng, Zigao; Xiao, Songwen

    2008-02-28

    The mechano-chemical (MC) dechlorination of polyvinyl chloride (PVC) and polyvinylidene chloride (PVDC) was performed by mechanical milling PVC/PVDC powder with zinc powder in a planetary ball mill, and the products of dechlorination were characterized by Infrared spectra (IR), X-ray diffraction (XRD), Raman spectroscopy, gas chromatography-mass spectrometry (GC-MS), and 13C solid-state nuclear magnetic resonance (NMR). The experimental results show that PVC/PVDC can be easily dechlorinated by milling with zinc powder, and formed various kinds of inorganic and organic products. Inorganic compounds included Zn2OCl(2).2H2O, Zn5(OH)8Cl2.H2O etc., and organic products involved diamond-like carbon, carbyne fragment, polyacetylene etc. Organic products formed following the paths of dechlorination, dehydrochlorination, crosslink, and oxidation. The mechano-chemical dechlorination process of PVC/PVDC may be an effective approach for carbyne synthesizing in the appropriate condition.

  13. PHASE EQUILIBRIUM FOR THE TERNARY SYSTEM VINYL CHLORIDE-CHLORINATED POLYETHYLENE-POLY (VINYL CHLORIDE)

    Institute of Scientific and Technical Information of China (English)

    LOU Jianfeng; WENG Zhixue; HUANG Zhiming; PAN Zuren

    1991-01-01

    Swelling capacity of vinyl chloride (VC) in chlorinated polyethylene (CPE) with 25- 40 wt% Cl at temperature 30- 57 ℃ was studied and their relationships were correlated with Langmuir and Freundlich adsorption equations. A ternary phase diagram for VC-CPE-PVC was also established.In-situ polymerization conditions of CPE-g -VC were proposed and CPE content control was analyzed for the manufacturing process of CPE-g-VC graft product based on results of phase equilibrium study.

  14. Comparative effects of hydrogen chloride gas on tomato and chrysanthemum. I. Distribution and accumulation of chloride following exposure. II. Pathological anatomy of hydrogen chloride gas injury

    Energy Technology Data Exchange (ETDEWEB)

    Shriner, D.S.

    1969-01-01

    Hydrogen chloride (HCl) gas damage to plants has not been a historically important problem. However, recent practices in a number of industries, particularly glass manufacturing and pyrolysis of waste plastics, have increased the seriousness of the problem. Studies were carried out under carefully controlled exposure conditions to determine the effects of HCl gas on a relatively sensitive and a relatively resistant plant species. The macroscopic symptoms of most importance in acute damage to tomato and chrysanthemum are glazing of the lower surface, and a bifacial bronzing of interveinal and marginal areas of leaves. Microscopically, glazing was shown to be caused by a collapse of the lower epidermal cells and a partial disorganization of the spongy mesophyll of leaves. Bronzing was shown to be caused by the further collapse of the spongy mesophyll, and in some cases the palisade mesophyll and upper epidermis. Analysis of plant tissues for their free chloride content following an exposure to HCl gas was done with cell-free water extracts which were titrated on an automatic chloride titrator. On the basis of such studies, evidence suggest that the mechanism of accumulation of chlorides in plants is similar to that of fluorides, and that in subacute doses, chlorides are translocated toward the extremities of the foliar portions of the plant. In areas where a number of different types of pollution sources exist, and symptomotology is not definitive in pinpointing the source, chloride analysis of plant tissues should prove valuable as an aid to diagnosis if HCl gas was suspected.

  15. Determination of Carbonyl Group Content in Plasma Proteins as a Useful Marker to Assess Impairment in Antioxidant Defense in Patients with Eales′ Disease

    Directory of Open Access Journals (Sweden)

    Rajesh Mohanraj

    2004-01-01

    Full Text Available Purpose: Formation of protein carbonyl groups is considered an early biomarker for the oxidant/antioxidant barrier impairment in various inflammatory diseases. We evaluated the intensity of free radical reactions in patients with Eales′ disease, an idiopathic inflammatory condition of the retina. Methods: Twenty patients with Eales′ disease in active vasculitis stage, 15 patients with Eales′ disease in healed vasculitis stage and 20 healthy control subjects were recruited for the study. Plasma protein carbonyl groups,plasma glutathione (GSH superoxide dismutase (SOD activity and thiobarbituric acid reactive substances (TBARS were determined in erythrocytes. Results: Plasma protein carbonyl content was elevated by a factor of 3.5 and 1.8 respectively in active and healed vasculitis stages. The increase of carbonyl group content in active and healed stage of patients with Eales′ disease correlated with diminished SOD activity and GSH content. There was also increased accumulation of TBARS in active and healed vasculitis stages of Eales′ disease, and this correlated with diminished SOD activity. Conclusion: Our results showed that protein carbonyl group content increases with severity of Eales′ disease. The increase in carbonyl content correlated with diminished antioxidant status. This confirms an earlier report that free radical mediated tissue damage occurs in Eales′ disease. The determination of protein carbonyl content may be used as a simple biomarker to monitor the efficacy of antioxidant supplementation in controlling retinal vasculitis in patients with Eales′ disease.

  16. Carbonyl sulfide (COS) as a tracer to constrain surface carbon fluxes

    Science.gov (United States)

    Yakir, Dan; Berkelhammer, Max; Miller, John; Montzka, Steve; Chen, Huilin

    2014-05-01

    provide additional constraints on the differential responses of photosynthesis and respiration, such as associated with C3 and C4 vegetation. Developing the use of COS as a powerful tracer of photosynthetic CO2 fluxes at all scales can help improve prediction of future responses of the terrestrial biosphere to changing environmental conditions. Key words Carbonyl sulfide, COS, Carbonic anhydrase, CA, ecosystem respiration, GPP, Biosphere-atmosphere interactions, soil COS uptake. References Asaf D, Rotenberg E, Tatarinov T, Dicken U, Montzka SA & Yakir D (2013) Ecosystem photosynthesis inferred from carbonyl sulfide flux measurements. Nature GeoScience, 6, 186-190; DOI: 10.1038/NGEO1730 Berry J, Wolf A, Campbell E, Baker I, Blake N, Blake D, Denning AS, Kawa SR, Montzka SA, Seibt UY, Stimler K, Yakir D Zhu Z (2013) A coupled model of the global cycles of carbonyl sulfide and CO2: A possible new window on the carbon cycle. J. Geophys. Res.: Biogeochem. 118, doi 10.1002/jgrg.20068, 2013 Stimler K, Berry JA, Montzka S, Yakir D (2011) Association between COS uptake and 18D during gas exchange in C3 and C4 leaves. Plant Physiol. Doi 10.1104/pp.111.176578

  17. Studies on Hypokalemia Induced by Trimethyltin Chloride

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    To determine the possible relationship between plasma potassium concentration and severity of acute trimethyltin chloride (TMT) poisoning and to assess the mechanism of TMT induced hypokalemia. Methods SD rats were treated with various dosages of TMT (ip). All the indices were measured and analysed for determing their possible relations with plasma K+. Results With increase of dosage, the plasma K+ level dropped rapidly, and deaths appeared more quickly. The LDs0 of TMT (ip) was 14.7 mg/kgbw. In the low dosage group (10 mg/kgbw), the plasma K+ level dropped slowly with the lowest dosage on day 6 (4.85 mmol/L). It rose again on day 11 (5.06 mmol/L), and recoverd on day 28. The poisoning signs corresponded with decline of the span of K+ level. The plasma Na+ level dropped half an hour after TMT treatment, but recovered 24 h later. In the high dosage group (46.4 mg/kgbw), the levels of plasma K+ and Na+ fell rapidly within half an hour (P<0.05), the intracellular potassium concentration of RBC did not decrerase obviously (P>0.05), the activities of Na+-K+-ATPase and Mg2+-ATPase in RBC membrane were depressed remarkably (P<0.01, P<0.05, respectively), the plasma aldosterone concentrations rose as high as tenfold (P<0.01), the arterial blood pH fell from 7.434 to 7.258 (P<0.01),pCO2 was raised from 29.62 to 45.33 mmHg (P<0.01). In the 24 h urine test, when rats were treated with TMT (21.5 mg/kgbw, ip), urine volume, urinary potassium, sodium and chloride increased significantly in comparison with those in the controls (P<0.01). Conclusion TMT could induce hypokalemia in SD rats. The available evidence suggests that TMT can induce acute renal leakage of potassium. At the same time, a significant rise of plasma aldosterone may play an important role in promoting potassium leakage from kidney to result in severe hypokalemia with inhaling acid-base abnormalities produced, which aggravate the poisoning symptoms. In the end the rats would die of respiratory

  18. Influence of Gas Components on the Formation of Carbonyl Sulfide over Water-Gas Shift Catalyst B303Q

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Water-gas shift reaction catalyst at lower temperature (200-400 ℃) may improve the conversion of carbon monoxide. But carbonyl sulfide was found to be present over the sulfided cobaltmolybdenum/alumina catalyst for water-gas shift reaction. The influences of temperature, space velocity,and gas components on the formation of carbonyl sulfide over sulfided cobalt-molybdenum/alumina catalyst B303Q at 200-400 ℃ were studied in a tubular fixed-bed quartz-glass reactor under simulated water-gas shift conditions. The experimental results showed that the yield of carbonyl sulfide over B303Q catalyst reached a maximum at 220 ℃ with the increase in temperature, sharply decreased with the increase in space velocity and the content of water vapor, increased with the increase in the content of carbon monoxide and carbon dioxide, and its yield increased and then reached a stable value with the increase in the content of hydrogen and hydrogen sulfide. The formation mechanism of carbonyl sulfide over B303Q catalyst at 200-400 ℃ was discussed on the basis of how these factors influence the formation of COS. The yield of carbonyl sulfide over B303Q catalyst at 200-400 ℃ was the combined result of two reactions, that is, COS was first produced by the reaction of carbon monoxide with hydrogen sulfide,and then the as-produced COS was converted to hydrogen sulfide and carbon dioxide by hydrolysis. The mechanism of COS formation is assumed as follows: sulfur atoms in the Co9Ss-MoS2/Al2O3 crystal lattice were easily removed and formed carbonyl sulfide with CO, and then hydrogen sulfide in the water-gas shift gas reacted with the crystal lattice oxygen atoms in CoO-MoO3/Al2O3 to form Co9Ss-MoS2/Al2O3.This mechanism for the formation of COS over water-gas shift catalyst B303Q is in accordance with the Mars-Van Krevelen's redox mechanism over metal sulfide.

  19. Synthesis of bidentate o-carborane-containing phosphine and arsine ligands and preparation of their complexes with chromium-, molybdenum-, tungsten-, iron- and nickel carbonyls

    International Nuclear Information System (INIS)

    A number of bidentate o-carborane phosphine and arsine ligands have been synthesized and their chelate complexes with carbonyls of chromium, molybdenum, tungsten, iron and nickel are obtained. 1-mercapto-2-dimethylarsnomethyl-o-carborane and 1-mercapto-2-diethylaminomethyl-o-carborane with molybdenum and tungsten carbonyls provide substitution products of only one CO group. 1-diphenylphosphino-2-diphenylphosphinomethyl-o-carborane and 1,2-bis(diphenylphosphinomethyl)-o-carborane form complexes with NiCl2. Simplicity of complex formation of bidentate carborane ligands with group 6 metal carbonyls increases in the series Cr(CO)6 6 6

  20. Conversion du methanol en ethanol par carbonylation suivie d'hydrogenolyse

    Science.gov (United States)

    Gaucher, Melissa

    Ce projet de maîtrise s'inscrit dans le cadre des nouvelles filières énergétiques renouvelables et s'effectue au sein de la Chaire de recherche industrielle sur l'éthanol cellulosique créée par trois partenaires industriels (Enerkem, CRB et Ethanol Greenfield) et le gouvernement du Québec en collaboration avec l'Université de Sherbrooke. La stratégie d'un des partenaires, Enerkem, est de convertir par gazéification des résidus de biomasse non homogène en Syngas, ce gaz est ensuite converti en méthanol puis en éthanol. L'objectif principal de ce projet est la conversion catalytique de l'acétate en alcool. Un catalyseur commercial, composé de cuivre et de chrome, a permis l'obtention des conversions de plus de 95 % et une sélectivité pour l'éthanol de plus de 50 % avec l'acétate de méthyle, de 99 % avec l'acétate d'éthyle et de 50 % avec l'acétate de butyle. Les conditions optimales trouvées impliquent une température de 215 °C, une pression de 350 psig, une vitesse spatiale de 1800 h -1 H2 STP et un ratio H2 : Acétate de 7. Un catalyseur alternatif, à base de cuivre et de zinc, a aussi été testé. L'objectif secondaire est la carbonylation du méthanol en acétate. Cette étape a été réalisée en phase gazeuse où des rendements très élevés, soit plus de 2000 kg d'acétate de méthyle par kg de métal précieux à l'heure (kg AM/ kg métal précieux/h), ont été obtenus. Les conditions d'opérations testées impliquent une température variant entre 200-240 °C, une pression entre 250-600 psig, des ratios McOH : CO de 1 à 2,5. Mots clés: Carbonylation, Éthanol, Hydrogénolyse, Catalyse hétérogène.

  1. Regulation of nonadiabatic processes in the photolysis of some carbonyl compounds.

    Science.gov (United States)

    Lin, King-Chuen

    2016-03-14

    Carbonyl compounds studied are confined to acetyl halide (CH3COCl), acetyl cyanide (CH3COCN), acetyl sulfide (CH3COSH), acetaldehyde (CH3CHO), and methyl formate (HCOOCH3). They are asymmetrically substituted, but do not follow the well-known Norrish type I reactions. Each compound ejected in an effusive beam at about 300 K is commonly excited to the (1)(n, π*)CO lower state; that is, a nonbonding electron on O of the C[double bond, length as m-dash]O group is promoted to the antibonding orbital of π*CO. The photolysis experiments are conducted in the presence of Ar gas and the corresponding fragments are detected using time-resolved Fourier-transform Infrared (FTIR) emission spectroscopy. The enhancement of the collision-induced internal conversion or intersystem crossing facilitates the dissociation channels via highly vibrational states of the ground singlet (So) or triplet (T1) potential energy surfaces. In this manner, an alternative nonadiabatic channel is likely to open yielding different products, even if the diabatic coupling strength is strong between the excited state and the neighboring state. For instance, the photodissociation of CH3COCl at 248 nm produces HCl, CO, and CH2 fragments, in contrast to the supersonic jet experiments showing dominance of the Cl fragment eliminated from the excited state. If the diabatic coupling strength is weak, dissociation proceeds mainly through internal conversion, such as the cases of CH3COCN and CH3COSH. The photodissociation of CH3COCN at 308 nm has never been reported before, while for CH3COSH matrix-isolated photodissociation was conducted that shows a distinct spectral feature from the current FTIR method. The CH3CHO and HCOOCH3 molecules belong to the same type of carbonyl compounds, in which the molecular products, CO + CH4 and CO + CH3OH, are produced through both transition state and roaming pathways. Their products are characterized differently between molecular beam and current FTIR experiments. For

  2. Redetermination of 1-carboxycyclohexan-1-aminium chloride

    Directory of Open Access Journals (Sweden)

    Teresa González

    2009-02-01

    Full Text Available The crystal structure of the title compound, C7H14NO2+·Cl−, was reported previously [Chacko, Srinivasan & Zand (1975. J. Cryst. Mol. Struct. 5, 353–357] from Weissenberg photographic data with R = 0.113. It has now been redetermined, providing a significant increase in the precision of the derived geometric parameters, viz. mean σ(C—C = 0.003 Å in the present work compared with 0.021 Å for the previous work. The complete cation is generated by crystallographic mirrror symmetry, with three C atoms, two O atoms and the N atom lying on the reflecting plane; the chloride anion also has m site symmetry. The crystal structure is established by a two-dimensional network of O—H...Cl and N—H...Cl hydrogen bonds, generating C12(4 and C12(7 chains, and R24(8 and R24(14 rings.

  3. Chloride, bromide and iodide scintillators with europium

    Energy Technology Data Exchange (ETDEWEB)

    Zhuravleva, Mariya; Yang, Kan

    2016-09-27

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  4. NQR in tert-butyl chloride

    Science.gov (United States)

    Brunetti, Aldo H.

    2004-03-01

    Tert-butyl chloride has been broadly studied experimentally through various techniques such as X-ray crystallography, DTA, and NMR. It was also studied experimentally through nuclear quadrupole resonance (NQR), but this study was limited and incomplete. In this paper, we present a more detailed study of TBC through the NQR of 35Cl. Our results show that near 120 K, the onset of the CH 3 groups semirotations around symmetry axis C3 takes place with an activation energy U=16.1 kJ mol -1. This intramolecular movement produces a T1 minimum near 148 K and is the dominant mechanism of the nuclear spin-lattice relaxation in phase III of this compound. In phase II of TBC, we show that there are not only methyl groups semirotations, but also semirotations of the whole molecule around a different axis from the symmetry axis C' 3 (C-Cl bond) with an activation energy of E=10.4 kJ mol -1.

  5. Denitrification of fertilizer wastewater at high chloride concentration

    DEFF Research Database (Denmark)

    Ucisik, Ahmed Süheyl; Henze, Mogens

    Wastewater from fertilizer industry is characterized by high contents of chloride concentration, which normally vary between 60 and 76 g/l. Experiments with bilogical denitrification were performed in lab-scale "fill and draw" reactors with synthetic wastewater with chloride concentrations up to 77.......4 g/l. The results of the experiments showed that biological denitrification was feasible at the extreme environmental conditions prevailing in fertilizer wastewater. Stable continuous biological denitrfication of the synthetic high chloride wastewater was performed up to 77.4 g Cl/l at 37 degree C...

  6. Calcium chloride in stabilised soil roads and runways

    Directory of Open Access Journals (Sweden)

    Harsh Vardhan

    1952-09-01

    Full Text Available Mudless, dustless, hard and all weather driving surfaces is a serious requirement of the forces.  surfacing by mixtures of definite amounts of locally available stone, gravel, sand, clay and Silt to which calculated amount of calcium chloride is added quickly compact and ultimately harden like concrete. This provides an easy, quick and economic- means of meeting the requirement.  Necessity of such surfaces, use and action of calcium chloride and resulting effects are discussed. Different methods of construction and application of calcium chloride are briefly related.

  7. Durability Analysis of Subway Station in Chloride Environment

    Directory of Open Access Journals (Sweden)

    Yang LuFeng

    2013-02-01

    Full Text Available In this study, a finite element model for chloride ions transport in saturated concrete was proposed based on the Fick’s second law of diffusion. The governing partial differential equation was solved numerically in space as a boundary-value problem and in time as an initial-value problem by means of the finite element formulations. The maximum allowable value of chloride diffusion coefficient within different locations of subway station with service life of 100a was achieved and suggestions for durability analysis of subway station in chloride environment were also proposed.

  8. The ionic product of water in concentrated tetramethylammonium chloride solutions.

    Science.gov (United States)

    Sipos, P; Bódi, I; May, P M; Hefter, G T

    1997-04-01

    The ionic product of water, pK(w) = - log[H(+)][OH(-)] has been determined in aqueous solutions of tetramethylammonium chloride over the concentration range of 0.1-5.5 M at 25 degrees C using high-precision glass electrode potentiometric titrations. pK(w) data relating to aqueous potassium and sodium chlorides at ionic strengths up to 5 M are markedly lower than the tetramethylammonium chloride results. These differences are almost certainly due to weak associations between potassium and (especially) sodium and hydroxide ions.

  9. Ionometric determination of chloride ion in circulating and waste waters

    Energy Technology Data Exchange (ETDEWEB)

    Bebeshko, G.I.; Afanas' eva, V.I.; Danielova, I.I.; Dmitriev, M.A.; Radchenko, A.F.

    1986-09-01

    The authors attempt to develop selective ionometric methods to determine chloride ion in waste and circulating waters from technological ore processing, containing significant amounts of sulfide ion and various flotation reagents. These waters contain practically no cations that form hard to dissolve compounds with chloride ion such as Ag/sup +/, Cu/sup +/, Hg/sup +/ or Pb/sup 2 +/. The chloride ion concentration in water varies between 10 and 100 mg/liter. Information is shown on the concentration of the main anions and flotation reagents in waters that were analyzed.

  10. Stochastic Modeling of Reinforced Concrete Structures Exposed to Chloride Attack

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Frier, Christian

    2003-01-01

    concentration and reinforcement cover depth are modeled by stochastic fields. The paper contains a description of the parameters to be included in a stochastic model and a proposal for the information needed to obtain values for the parameters in order to be ab le to perform reliability investigations...... the reinforcement exceeds a critical threshold value. In the present paper a stochastic model is described by which the chloride content in a reinforced concrete structure can be estimated. The chloride ingress is modeled by a 2-dimensional diffusion process and the diffusion coefficient, surface chloride...

  11. Applicability of boron-doped diamond electrode to the degradation of chloride-mediated and chloride-free wastewaters

    International Nuclear Information System (INIS)

    The electrochemical degradation of chloride-mediated and chloride-free dye wastewaters was investigated on a boron-doped diamond (BDD) electrode in comparison with that on a dimensionally stable anode (DSA), and the applicability of BDD electrode to the degradation of these two kinds of wastewaters was explored. In chloride-free wastewater, the electrochemical degradation efficiency of dye on BDD electrode was much higher than that on DSA, with a chemical oxygen demand (COD) removal of 100% and 26% for BDD and DSA, respectively. In chloride-mediated dye wastewater, COD removal was faster than that in chloride-free wastewater on both BDD and DSA electrodes with COD removal efficiencies higher than 95%, whereas the rate of COD removal on DSA was faster than that on BDD electrode. The investigation indicates that DSA is more suitable than BDD electrode in degradation of originally chloride contained dye wastewaters for the sake of energy and time saving. However, for chloride-free dye wastewaters, with the aim of environmental protection, BDD electrode is more appropriate to realize complete mineralization. At the same time, the secondary pollution can be avoided

  12. Effects of low concentration biodiesel blends application on modern passenger cars. Part 2: impact on carbonyl compound emissions.

    Science.gov (United States)

    Fontaras, Georgios; Karavalakis, Georgios; Kousoulidou, Marina; Ntziachristos, Leonidas; Bakeas, Evangelos; Stournas, Stamoulis; Samaras, Zissis

    2010-07-01

    Today in most European member states diesel contains up to 5% vol biodiesel. Since blending is expected to increase to 10% vol, the question arises, how this higher mixing ratio will affect tailpipe emissions particularly those linked to adverse health effects. This paper focuses on the impact of biodiesel on carbonyl compound emissions, attempting also to identify possible relationship between biodiesel feedstock and emissions. The blends were produced from five different feedstocks, commonly used in Europe. Measurements were conducted on a Euro 3 common-rail passenger car over various driving cycles. Results indicate that generally the use of biodiesel at low concentrations has a minor effect on carbonyl compound emissions. However, certain biodiesels resulted in significant increases while others led to decreases. Biodiesels associated with increases were those derived from rapeseed oil (approx. 200%) and palm oil (approx. 180%), with the highest average increases observed at formaldehyde and acroleine/acetone.

  13. Study of the formation of carbonyl compounds in edible oils and fats by 1H-NMR and FTIR

    Science.gov (United States)

    Moya Moreno, M. C. M.; Mendoza Olivares, D.; Amézquita López, F. J.; Peris Martínez, V.; Bosch Reig, F.

    1999-05-01

    Oils and fats start decomposing from the moment they are isolated from their natural environment. Heating accelerates oxidative rancidity and frying at high temperatures produces thermal degradation with the formation of decomposition products, such as aldehydes, ketones, free acids and hydroxilic compounds that in high levels can be harmful to human health. The decomposition products formed up to 300°C were determined by means of 1H-NMR spectroscopy and an FTIR spectroscopic method was developed for the quantification of carbonyl compounds generated during heating. The results show that there is a formation of carbonyl compounds starting at 150°C and when the sample was heated at 300°C for 40 min, the following contents (expressed as butyraldehyde mass fraction) were found: olive oil 10.5%, sunflower oil 11.3%, corn oil 3.0%, seeds oil (sunflower, safflower and canola seed) 6.6% and lard 3.5%.

  14. Rheological properties of magnetorheological suspensions based on core-shell structured polyaniline-coated carbonyl iron particles

    Science.gov (United States)

    Sedlačík, M.; Pavlínek, V.; Sáha, P.; Švrčinová, P.; Filip, P.; Stejskal, J.

    2010-11-01

    The sedimentation caused by the high density of suspended particles used in magnetorheological fluids is a significant obstacle for their wider application. In the present paper, core-shell structured carbonyl iron-polyaniline particles in silicone oil were used as a magnetorheological suspension with enhanced dispersion stability. Bare carbonyl iron particles were suspended in silicone oil to create model magnetorheological suspensions of different loading. For a magnetorheological suspension of polyaniline-coated particles the results show a decrease in the base viscosity. Moreover, the polyaniline coating has a negligible influence on the MR properties under an external magnetic field B. The change in the viscoelastic properties of magnetorheological suspensions in the small-strain oscillatory shear flow as a function of the strain amplitude, the frequency and the magnetic flux density was also investigated.

  15. Role of the oceans in the atmospheric cycle of carbonyl sulfide

    International Nuclear Information System (INIS)

    Carbonyl sulfide (OCS) is both the dominant sulfur gas in the remote troposphere and, along with volcanoes, a major source of sulfur for the stratospheric sulfate layer. Prior to this work the ocean was regarded as a major sink for atmospheric OCS. The purpose of this study has been to assess the magnitude of the global air-sea flux of OCS. The author designed an analytical system which was centered around a Varian-3700 gas chromatograph with a flame-photometric detector. To increase the sensitivity of the detector, the hydrogen gas for the flame was doped with sulfur hexafluoride. Air samples were concentrated in a liquid nitrogen cooled freeze-out loop, then injected into the gas chromatograph. Water samples purged with sulfur-free zero-air which was analyzed similarly. He also built a permeation tube system for chemical standardization. This equipment was taken on two oceanographic cruises on the Pacific Ocean, one in the spring of 1983 and a second in the spring of 1983. Both of these cruises included measurements of air and seawater concentrations of OCS from the equator to the Aleutian Islands. The Henry's law constant of solubility for OCS was measured in the laboratory for filtered and boiled seawater at three temperatures

  16. White light generation by carbonyl based indole derivatives due to proton transfer: an efficient fluorescence sensor.

    Science.gov (United States)

    Singla, Nidhi; Bhadram, Venkata Srinu; Narayana, Chandrabhas; Chowdhury, Papia

    2013-04-01

    The motivation of the present work is to understand the optical, chemical, and electrical aspects of the proton transfer mechanism of indole (I) and some carbonyl based indole derivatives: indole-3-carboxaldehyde (I3C) and indole-7-carboxaldehyde (I7C) for both powder form and their liquid solution. Structural information for indole derivatives (isolated molecule and in solution) is obtained with density functional theory (DFT) and time dependent DFT (TD-DFT) methods. Calculated transition energies are used to generate UV-vis, FTIR, Raman, and NMR spectra which are later verified with the experimental spectra. The occurrence of different conformers [cis (N(c)), trans (N(t)), and zwitterion (Z*)] have been interpreted by Mulliken charge, natural bond orbital (NBO) analysis, and polarization versus electric field (P-E loop) studies. (1)H and (13)C NMR and molecular vibrational frequencies of the fundamental modes established the stability of Nc due to the presence of intramolecular hydrogen bonding (IHB) in the ground state (S0). Computed/experimental UV-vis absorption/emission studies reveal the creation of new species: zwitterion (Z*) and anion (A*) in the excited state (S1) due to excited state intramolecular and intermolecular proton transfer (ESI(ra)PT and ESI(er)PT). Increased electrical conductivity (σ(ac)) with temperature and increased ferroelectric polarization at higher field verifies proton conduction in I7C.

  17. Quantitative modeling of bioconcentration factors of carbonyl herbicides using multivariate image analysis.

    Science.gov (United States)

    Freitas, Mirlaine R; Barigye, Stephen J; Daré, Joyce K; Freitas, Matheus P

    2016-06-01

    The bioconcentration factor (BCF) is an important parameter used to estimate the propensity of chemicals to accumulate in aquatic organisms from the ambient environment. While simple regressions for estimating the BCF of chemical compounds from water solubility or the n-octanol/water partition coefficient have been proposed in the literature, these models do not always yield good correlations and more descriptive variables are required for better modeling of BCF data for a given series of organic pollutants, such as some herbicides. Thus, the logBCF values for a set of carbonyl herbicides comprising amide, urea, carbamate and thiocarbamate groups were quantitatively modeled using multivariate image analysis (MIA) descriptors, derived from colored image representations for chemical structures. The logBCF model was calibrated and vigorously validated (r(2) = 0.79, q(2) = 0.70 and rtest(2) = 0.81), providing a comprehensive three-parameter linear equation after variable selection (logBCF = 5.682 - 0.00233 × X9774 - 0.00070 × X813 - 0.00273 × X5144); the variables represent pixel coordinates in the multivariate image. Finally, chemical interpretation of the obtained models in terms of the structural characteristics responsible for the enhanced or reduced logBCF values was performed, providing key leads in the prospective development of more eco-friendly synthetic herbicides. PMID:26971171

  18. Quantification of A Tropical Missing Source From Ocean For The Carbonyl Sulfide Global Budget

    Science.gov (United States)

    Kuai, Le; Worden, John; Campbell, Elliott; Kulawik, Susan; Lee, Meemong; Montzka, Stephen; Berry, Joe; Baker, Ian; Denning, Scott; Kawa, Randy; Bian, Huisheng; Yung, Yuk

    2015-04-01

    Quantifying the carbonyl sulfide (OCS) surface fluxes contributes to the understanding of both sulfur cycle and carbon cycle. Although the major sources and sinks of OCS are well recognized, the uncertainties of individual types of the fluxes remain large. With the understanding of a large underestimate of ecosystem uptake, it suggests a large missing ocean source over tropical region to compensate the increased sink. However before AURA Tropospheric Emissions Spectrometer (TES) OCS data is released, no direct measurements have been taken to test this hypothesis. In this study, we performed a flux inversion to update the fluxes from TES OCS. Then we compared three experimental GEOS-Chem forward model runs driven by different fluxes based on TES inversion to HIPPO aircraft estimates in free troposphere and also to NOAA near surface observations. The TES data supports the hypothesis that a large source from tropical ocean is missing in the current OCS global budget and suggests that the source is even larger than that proposed in Berry et al., (2013). Consequently, it leads to a larger land uptake and increase the estimates of GPP. TES data also suggests the missing oceanic source is not symmetric about equator. It is strong and distributed further north of the equator (to 40°N) but weak and narrow south of the equator (to 20°S).

  19. [Purification and characterization of carbonyl enantioselective reductase from Morganella morganii J-8].

    Science.gov (United States)

    Zhang, Peng-Hu; Zhang, Liang; Lu, Yan; Shi, Gui-Yang

    2007-03-01

    The purification and the characteristics of an enzyme from Morganella morganii J-8, which could produce d-pseudoephedrine from 1-phenyl-2-methylamine-acetone, were performed in this study. In this research, first, cells were disrupted by ultrasonic treatment at 4 degrees C. The carbonyl enantioselective reductase was purified with a combination of ammonium precipitation, Phenyl Superose hydrophobic chromatography, DEAE anion exchange, and native polyacrylamide gel electrophoresis. The molecular mass of the purified enzyme subunit was estimated to be 42.5kD on sodium dodecyl sulfate-polyacrylamide electrophoresis (SDS-PAGE). The native molecular mass of the enzyme that was analyzed by high-performance liquid chromatography was found out to be 84.1 kD, which indicated that the enzyme was a dimmer. The purified enzyme was analyzed by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry, and the result showed that the purified enzyme had high homology with leucine dehydrogenase.

  20. The Behaviour of Protein Carbonyls in Newborns with Birth Respiratory Distress and Asphyxia

    Directory of Open Access Journals (Sweden)

    Gabriela ZAHARIE

    2009-12-01

    Full Text Available Objective: A prospective study was carried out in premature newborns with respiratory distress syndrome (RDS and asphyxia at birth in order to identify and analyze the effects of RDS on proteins. Material and Methods: Protein peroxidation was studied using the Reznick spectrophotometric method. The study group included 14 premature newborns with respiratory distress and asphyxia at birth. The control group included 13 newborns that were born on term, eutrophic and healthy. The determinations were carried out using venous blood. Statistical data analyses were performed using Statistica software. The comparisons between groups (study and controls were performed by applying parametric and non-parametric tests according with the type of distribution. Results: Statistically significant correlations were found between the value of protein carbonyls (PC and the weight of premature newborns in the case group (p < 0.05, as well as between the PC value and the presence of respiratory distress due to surfactant deficiency in the study group. The average PC value in the study group was higher in the third day as compared with the first day. The PC value was significantly higher in the control group as compared with study group. Conclusion: The results of our study revealed that the respiratory distress in the premature newborn and oxygen therapy stimulate the peroxidation of proteins.

  1. Exchange of carbonyl sulfide (COS between the atmosphere and various soils in China

    Directory of Open Access Journals (Sweden)

    J. Liu

    2009-11-01

    Full Text Available Using a dynamic enclosure, the exchange fluxes of carbonyl sulfide (COS between the atmosphere and 18 soils from 10 provinces in China were investigated. The emission or uptake of COS from the soils was highly dependent on the soil type, soil temperature, soil moisture, and atmospheric COS mixing ratio. In general, with the only exception being paddy soils, the soils in this investigation acted as sinks for atmospheric COS under wide ranges of soil temperature and soil moisture. Two intensively investigated wheat soils and one forest soil, had optimal soil temperatures for COS uptake of around 15°C, and the optimal soil water content varied from 13 to 58%. The two paddy soils, exponentially COS emission fluxes increased with increasing soil temperature, and decreased COS emission fluxes with increased soil water content. However, negligible emission was found when the paddy soils were under waterlogging status. The observed compensation points for various soils were different and increased significantly with soil temperature. The laboratory simulation agreed with the preliminary field measurements for the paddy soil in Jiaxing, Zhejiang province.

  2. Ruthenium(II) carbonyl complexes containing chalconates and triphenylphosphine/arsine

    Indian Academy of Sciences (India)

    P Viswanathamurthi; M Muthukumar

    2011-09-01

    A series of new hexa-coordinated ruthenium(II) carbonyl complexes of the type [RuCl(CO)(EPh3)(B)(L1−4)] (4-15) (E = P or As; B = PPh3, AsPh3 or Py; L = 2'-hydroxychalcone) were synthesized from the reaction of [RuHCl(CO)(EPh3)2(B)] (1-3) (E = P or As; B = PPh3, AsPh3 or Py) with equimolar chalcone in benzene under reflux. The new complexes have been characterized by analytical and spectroscopic (IR, electronic, 1H, 31P{1H}, and 13C NMR) methods. On the basis of data obtained, an octahedral structure has been assigned for all the complexes. The complexes exhibit catalytic activity for the oxidation of primary and secondary alcohols into their corresponding aldehydes and ketones in the presence of -methylmorpholine--oxide (NMO) as co-oxidant and were also found to be efficient transfer hydrogenation catalysts. The antifungal properties of the ligands and their complexes have also been examined and compared with standard Bavistin.

  3. Understanding fog-plant interactions at the ecosystem scale using atmospheric carbonyl sulfide

    Science.gov (United States)

    Campbell, J. E.; Whelan, M.; Stinecipher, J.; Zumkehr, A. L.; Berry, J. A.; Dawson, T. E.; Seibt, U.; Hilton, T. W.; Kulkarni, S.; Commane, R.; Angevine, W. M.; Lu, Y.; Herndon, S. C.; Zahniser, M. S.

    2015-12-01

    Ecosystem metabolism is thought to have powerful feedbacks with the climate system as well as direct impacts on individual taxa that rely on ecosystems for food, water, and shelter. Despite the importance of an ecosystem level understanding, climate change impacts on whole ecosystems remains highly uncertain. In particular, coastal fog-dominated regions are a blind spot for whole ecosystem measurements of the land-air-sea exchange of carbon, water, and energy. To address this critical knowledge gap, our inter-displicary team from the University of California's new Institute for the Study of Ecological Effects of Climate Impacts (ISEECI) has launched a next-generation monitoring program along a gradient of UC Natural Reserve System (NRS) sites. We leverage recent breakthroughs in atmospheric spectroscopy and mechanistic ecosystem models of carbonyl sulfide that provide an unprecedented opportunity to explore the sustainability of coastal systems. Here we present our next-generation monitoring and regional analysis across a North/South transect of UC-NRS sites that has the potential to provide a new window into fog-dominated ecosystems, both currently and under climate change scenarios.

  4. Extraction of cobalt(II) from aqueous solution by N,N'-carbonyl difatty amides

    Institute of Scientific and Technical Information of China (English)

    Emad A. Jaffar Al-Mulla; Khalid Waleed S. Al-Janabi

    2011-01-01

    The development of economic and environmentally friendly extractants to recover cobalt metal is required due to the increasing demand for this metal. In this study, solvent extraction of Co(Ⅱ) from aqueous solution using a mixture of N,N'-carbonyl difatty amides (CDFAs) synthesised from palm oil as the extractant was carried out. The effects of various parameters such as acid, contact time, extractant concentration, metal ion concentration and stripping agent and the separation of Co(Ⅱ) from other metal ions such as Fe(Ⅱ), Ni(Ⅱ), Zn(Ⅲ) and Cd(Ⅱ) were investigated. It was found that the extraction of Co(Ⅱ) into the organic phase involved the formation of 1:1 complexes. Co(Ⅱ) was successfully separated from commonly associated metal ions such as Fe(Ⅱ), Ni(Ⅱ), Zn(Ⅲ) and Cd(Ⅱ). Co(Ⅱ) stripping from the loaded organic phase was studied in aqueous solution. These results are useful to recover Co(Ⅱ) from aqueous solution utilising (CDFAs) as an extractant.

  5. Microwave absorbing property of silicone rubber composites with added carbonyl iron particles and graphite platelet

    International Nuclear Information System (INIS)

    Silicone rubber composites filled with carbonyl iron particles (CIPs) and graphite platelet (GP) were prepared using non-coating or coating processes. The complex permittivity and permeability of the composites were measured using a vector network analyzer in the frequency range of 1–18 GHz and dc electric conductivity was measured by the standard four-point contact method. The results showed that CIPs/GP composites fabricated in the coating process had the highest permittivity and permeability due to the particle orientation and interactions between the two absorbents. The coating process resulted in a decreased effective eccentricity of the absorbents, and the dc conductivity increased according to Neelakanta's equations. The reflection loss (RL) value showed that the composites had an excellent absorbing property in the L-band, minimum −11.85 dB at 1.5 mm and −15.02 dB at 2 mm. Thus, GP could be an effective additive in preparing thin absorbing composites in the L-band. - Highlights: ► The added GP increased the permittivity and permeability of composites filled with CIPs. ► The enhancement was owing to interactions of the two absorbents and the fabrication process. ► The coating process decreased the effective eccentricity of the particles, and increased the conductivity of the composites. ► The composites to which CIPs/GP were added in coating process had excellent absorbing properties in the L-band.

  6. Emissions of polyciclic aromatic hydrocarbons and polyciclic carbonyl biphenils from electric arc furnaces

    Directory of Open Access Journals (Sweden)

    P. Gomes, J. F.

    2008-06-01

    Full Text Available This paper describes work done in order to determine the emissions of highly toxic organic micropollutants from electric arc furnaces used in the production of carbon steel from scrap. The study will be allowing to derive relationships between the levels of airborne micropollutants and the operational parameters of the production process so that an abatement of pollution could be achieved. By using the European standard method CEN 1948 for dioxin like compounds sampling and measurement, it was possible to determine the characteristic fingerprint of micropollutants such as polyciclic aromatic hydrocarbons (PAHs and polycyclic carbonyl biphenils (PCBs emitted by this particular stationary source.

    Este artículo contiene resultados del trabajo ejecutado para estudiar la determinación de las emisiones de los micropolutantes orgánicos muy tóxicos que se emiten por los hornos eléctricos de arco utilizados en la producción de acero. Este estudio inicial va a permitir relacionar las concentraciones de polutantes emitidos a la atmósfera con las condiciones de operación del horno eléctrico de arco. Utilizando el método normalizado CEN 1948 para captación y análisis de muestras de compuestos análogos a las dioxinas ha sido posible determinar el perfil característico de los micropolutantes tales como PAHs y PCBs emitidos por esta fuente.

  7. Proteomic profile of carbonylated proteins in rat liver: discovering possible mechanisms for tetracycline-induced steatosis.

    Science.gov (United States)

    Deng, Zhenglu; Yan, Siyu; Hu, Hui; Duan, Zhigui; Yin, Lanxuan; Liao, Shenke; Sun, Yubai; Yin, Dazhong; Li, Guolin

    2015-01-01

    To investigate biochemical mechanisms for the tetracycline-induced steatosis in rats, targeted proteins of oxidative modification were profiled. The results showed that tetracycline induced lipid accumulation, oxidative stress, and cell viability decline in HepG2 cells only under the circumstances of palmitic acid overload. Tetracycline administration in rats led to significant decrement in blood lipids, while resulted in more than four times increment in intrahepatic triacylglycerol and typical microvesicular steatosis in the livers. The triacylglycerol levels were positively correlated with oxidative stress. Proteomic profiles of carbonylated proteins revealed 26 targeted proteins susceptible to oxidative modification and most of them located in mitochondria. Among them, the long-chain specific acyl-CoA dehydrogenase was one of the key enzymes regulating fatty acid β-oxidation. Oxidative modification of the enzyme in the tetracycline group depressed its enzymatic activity. In conclusion, the increased influx of lipid into the livers is the first hit of tetracycline-induced microvesicular steatosis. Oxidative stress is an essential part of the second hit, which may arise from the lipid overload and attack a series of functional proteins, aggravating the development of steatosis. The 26 targeted proteins revealed here provide a potential direct link between oxidative stress and tetracycline-induced steatosis. PMID:25332112

  8. Di-μ-carbonyl-bis-[bis-(triphenyl-phos-phane)rhodium(0)](Rh-Rh) acetone disolvate.

    Science.gov (United States)

    Gueorguieva, Petia G; Laneman, Scott A; Stanley, George G; Fronczek, Frank R; Watkins, Steven F

    2012-11-01

    The dirhodium complex, [Rh(2)(C(18)H(15)P)(4)(CO)(2)]·2(CH(3))(2)CO, has crystallographic twofold symmetry and the Rh-Rh distance is 2.6266 (8) Å. The four atoms proximate to each Rh atom [Rh-P = 2.3222 (7) and 2.3283 (8) Å, and Rh-C = 1.961 (3) and 2.045 (3) Å] form a distorted tetra-hedron with large deviations from the putative tetra-hedral angles [r.m.s. deviation = 23 (1)°]. The six angles more closely approximate those of a trigonal bipyramid [r.m.s. deviation = 14 (1)°] with one missing equatorial ligand. The two bridging carbonyl ligands are much more linearly coordinated to one Rh [Rh-C O = 151.0 (2)°] than to the other [127.0 (2)°], and the two Rh(2)CO planes form a dihedral angle of 45.43 (5)°. The two acetone solvent mol-ecules are disordered, and their estimated scattering contribution was subtracted from the observed diffraction data using the SQUEEZE routine in PLATON [Spek (2009 ▶). Acta Cryst.D65, 148-155]. PMID:23284375

  9. The flux of carbonyl sulfide and carbon disulfide between the atmosphere and a spruce forest

    Directory of Open Access Journals (Sweden)

    X. Xu

    2002-01-01

    Full Text Available Turbulent fluxes of carbonyl sulfide (COS and carbon disulfide (CS2 were measured over a spruce forest in Central Germany using the relaxed eddy accumulation (REA technique. A REA sampler was developed and validated using simultaneous measurements of CO2 fluxes by REA and by eddy correlation. REA measurements were conducted during six campaigns covering spring, summer, and fall between 1997 and 1999. Both uptake and emission of COS and CS2 by the forest were observed, with deposition occurring mainly during the sunlit period and emission mainly during the dark period. On the average, however, the forest acts as a sink for both gases. The average fluxes for COS and CS2 are  -93 ± 11.7 pmol m-2 s-1 and  -18 ± 7.6 pmol m-2 s-1, respectively. The fluxes of both gases appear to be correlated to photosynthetically active radiation and to the CO2 and chem{H_2O} fluxes, supporting the idea that the air-vegetation exchange of both gases is controlled by stomata. An uptake ratio COS/CO2 of 10 ± 1.7 pmol m mol-1 has been derived from the regression line for the correlation between the COS and CO2 fluxes. This uptake ratio, if representative for the global terrestrial net primary production, would correspond to a sink of 2.3 ± 0.5 Tg COS yr-1.

  10. Estimate of carbonyl sulfide tropical oceanic surface fluxes using Aura Tropospheric Emission Spectrometer observations

    Science.gov (United States)

    Kuai, Le; Worden, John R.; Campbell, J. Elliott; Kulawik, Susan S.; Li, King-Fai; Lee, Meemong; Weidner, Richard J.; Montzka, Stephen A.; Moore, Fred L.; Berry, Joe A.; Baker, Ian; Denning, A. Scott; Bian, Huisheng; Bowman, Kevin W.; Liu, Junjie; Yung, Yuk L.

    2015-10-01

    Quantifying the carbonyl sulfide (OCS) land/ocean fluxes contributes to the understanding of both the sulfur and carbon cycles. The primary sources and sinks of OCS are very likely in a steady state because there is no significant observed trend or interannual variability in atmospheric OCS measurements. However, the magnitude and spatial distribution of the dominant ocean source are highly uncertain due to the lack of observations. In particular, estimates of the oceanic fluxes range from approximately 280 Gg S yr-1 to greater than 800 Gg S yr-1, with the larger flux needed to balance a similarly sized terrestrial sink that is inferred from NOAA continental sites. Here we estimate summer tropical oceanic fluxes of OCS in 2006 using a linear flux inversion algorithm and new OCS data acquired by the Aura Tropospheric Emissions Spectrometer (TES). Modeled OCS concentrations based on these updated fluxes are consistent with HIAPER Pole-to-Pole Observations during 4th airborne campaign and improve significantly over the a priori model concentrations. The TES tropical ocean estimate of 70 ± 16 Gg S in June, when extrapolated over the whole year (about 840 ± 192 Gg S yr-1 ), supports the hypothesis proposed by Berry et al. (2013) that the ocean flux is in the higher range of approximately 800 Gg S yr-1.

  11. The Field-Dependent Rheological Properties of Magnetorheological Grease Based on Carbonyl-Iron-Particles

    Science.gov (United States)

    Mohamad, N.; Mazlan, S. A.; Ubaidillah; Choi, Seung-Bok; Nordin, M. F. M.

    2016-09-01

    This paper presents dynamic viscoelastic properties of magnetorheological (MR) grease under variation of magnetic fields and magnetic particle fractions. The tests to discern the field-dependent properties are undertaken using both rotational and oscillatory shear rheometers. As a first step, the MR grease is developed by dispersing the carbonyl iron (CI) particles into grease medium with a mechanical stirrer. Experimental data are obtained by changing the magnetic field from 0 to 0.7 T at room temperature of 25 °C. It is found that a strong Payne effect limits the linear viscoelastic region of MR grease at strains above 0.1%. The results exhibit a high dynamic yield stress which is equivalent to Bingham plastic rheological model, and show relatively good MR effect at high shear rate of 2000 s‑1. In addition, high dispersion of the magnetic particles and good thermal properties are proven. The results presented in this work directly indicate that MR grease is a smart material candidate that could be widely applicable to various fields including vibration control.

  12. Atmospheric measurements of carbonyl sulfide, dimethyl sulfide, and carbon disulfide using the electron capture sulfur detector

    Science.gov (United States)

    Johnson, James E.; Bates, Timothy S.

    1993-01-01

    Measurements of atmospheric dimethyl sulfide (DMS), carbonyl sulfide (COS), and carbon disulfide (CS2) were conducted over the Atlantic Ocean on board the NASA Electra aircraft during the Chemical Instrumentation Test and Evaluation (CITE 3) project using the electron capture sulfur detector (ECD-S). The system employed cryogenic preconcentration of air samples, gas chromatographic separation, catalytic fluorination, and electron capture detection. Samples collected for DMS analysis were scrubbed of oxidants with NaOH impregnated glass fiber filters to preconcentration. The detection limits (DL) of the system for COS, DMS, and CS2 were 5, 5, and 2 ppt, respectively. COS concentrations ranged from 404 to 603 ppt with a mean of 489 ppt for measurements over the North Atlantic Ocean (31 deg N to 41 deg N), and from 395 to 437 ppt with a mean of 419 ppt for measurements over the Tropical Atlantic Ocean (11 deg S to 2 deg N). DMS concentrations in the lower marine boundary layer, below 600-m altitude, ranged from below DL to 150 ppt from flights over the North Atlantic, and from 9 to 104 ppt over the Tropical Atlantic. CS2 concentrations ranged from below DL to 29 ppt over the North Atlantic. Almost all CS2 measurements over the Tropical Atlantic were below DL.

  13. Observations of the uptake of carbonyl sulfide (COS by trees under elevated atmospheric carbon dioxide concentrations

    Directory of Open Access Journals (Sweden)

    L. Sandoval-Soto

    2012-02-01

    Full Text Available Global change affects ecosystems to adapt to elevated atmospheric concentrations of carbon dioxide (CO2. We understand that carbonyl sulfide (COS, a trace gas which is involved in building up the stratospheric sulfate aerosol layer, is taken up by vegetation with the same triad of the enzmyes which are metabolizing the CO2, i.e. Ribulose-1,5-bisphosphate Carboxylase-Oxygenase (Rubisco, Phosphoenolpyruvate Carboxylase (PEP-Co and carbonic anhydrase (CA. Therefore, we discuss a physiological/biochemical adaptation of these enzymes to affect the sink strength of vegetation for COS. We investigated the adaption of two European tree species, Fagus sylvatica and Quercus ilex, grown inside chambers under elevated CO2 and determined the exchange characteristics and the content of CA after a 1–2 yr period of adaption from 350 ppm to 800 ppm CO2. We could demonstrate that the COS compensation point, the CA activity and the deposition velocities may change and cause a decrease of the COS uptake by plant ecosystems. As a consequence, the atmospheric COS level may rise leading to higher input of this trace gas into the stratosphere and causing a higher energy reflection by the stratospheric sulfur aerosol into space, thus counteracting the direct radiative forcing by the tropospheric COS.

  14. Protein carbonyl levels correlate with performance in elite field hockey players.

    Science.gov (United States)

    Rosa-Lima, Frederico Luis; Lannes, Luiz; Viana-Gomes, Diego; Pierucci, Anna Paola T R; Salerno, Verônica P

    2015-07-01

    Excess and incorrectly selected exercise can degrade athletic performance from an imbalance in redox homeostasis and oxidative stress, but well-planned training and nutrition can improve antioxidant capacity. The aim of the study was to investigate how nutrient intake could influence oxidative stress and cell lesion biomarkers after 5 days of training followed by a game. Blood was collected from 10 athletes at the start of training (basal), after training (pre-game), and postgame. Their acceleration capacity also was measured pre- and postgame. Blood analysis showed an increase in lactate concentration postgame (13%) and total antioxidant capacity increased both pre-game (13.1%) and postgame (12.7%), all in comparison with basal levels. An oxidative stress marker, protein carbonyl (PC), increased 3-fold over the course of the game, which correlated with a decreased acceleration (r = 0.749). For biomarkers of tissue damage, creatine kinase and aspartate transaminase (AST) increased postgame by 150% and 75%, respectively. The AST variation had a high negative correlation with energy and carbohydrate consumption and a moderate correlation with lipid and vitamin C intake. Protein intake had a positive but moderate correlation with reduced glutathione. The observed correlations suggest that nutritional monitoring can improve exercise physiological homeostasis and that PC serves as a good biomarker for oxidative stress and performance loss.

  15. A glutathione-based system for defense against carbonyl stress in Haemophilus influenzae

    Directory of Open Access Journals (Sweden)

    Kidd Stephen P

    2012-07-01

    Full Text Available Abstract Background adhC from Haemophilus influenzae encodes a glutathione-dependent alcohol dehydrogenase that has previously been shown to be required for protection against killing by S-nitrosoglutathione (GSNO. This group of enzymes is known in other systems to be able to utilize substrates that form adducts with glutathione, such as aldehydes. Results Here, we show that expression of adhC is maximally induced under conditions of high oxygen tension as well as specifically with glucose as a carbon source. adhC could also be induced in response to formaldehyde but not GSNO. An adhC mutant was more susceptible than wild-type Haemophilus influenzae Rd KW20 to killing by various short chain aliphatic aldehydes, all of which can be generated endogenously during cell metabolism but are also produced by the host as part of the innate immune response. Conclusions These results indicate that AdhC plays a role in defense against endogenously generated reactive carbonyl electrophiles in Haemophilus influenzae and may also play a role in defense against the host innate immune system.

  16. Comparison of extraction techniques and mass spectrometric ionization modes in the analysis of wine volatile carbonyls

    Energy Technology Data Exchange (ETDEWEB)

    Zapata, Julian; Mateo-Vivaracho, Laura; Cacho, Juan [Laboratory for Flavor Analysis and Enology, Institute of Engineering of Aragon, I3A, Department of Analytical Chemistry, Faculty of Sciences, University of Zaragoza, 50009 Zaragoza (Spain); Ferreira, Vicente, E-mail: vferre@unizar.es [Laboratory for Flavor Analysis and Enology, Institute of Engineering of Aragon, I3A, Department of Analytical Chemistry, Faculty of Sciences, University of Zaragoza, 50009 Zaragoza (Spain)

    2010-02-15

    This work presents a comparative study of the analytical characteristics of two methods for the analysis of carbonyl compounds in wine, both based on the derivatization with O-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine hydrochloride (PFBHA). In the first method derivatives are formed in the solid phase extraction (SPE) cartridge in which the analytes have been previously isolated, while in the second method derivatives are formed in a solid phase microextraction (SPME) fibre saturated with vapors of the reagent and exposed to the sample headspace. In both cases detection has been carried out by electron impact (EI) or negative chemical ionization (NCI) mass spectrometry. The possibility of determining haloanisols simultaneously has been also considered. The method based on SPE presents, in general, better analytical properties than the SPME one. Although linearity was satisfactory for both methods (R{sup 2} > 0.99), repeatability of the SPE method (RSD < 10%) was better than that obtained with SPME (9% < RSD < 20%). Detection limits obtained with EI are better for the SPE method except for trihaloanisols, while with NCI detection limits for both strategies are comparable, although the SPME strategy presents worse results for ketones and methional. Detection limits are always lower with NCI, being the improvement most notable for SPME. Recovery experiments show that in the case of SPE, uncertainties are lower than 12% in all cases, while with the SPME method the imprecision plus the existence of matrix effects make the global uncertainty to be higher than 15%.

  17. Adsorption of Tetradecylpyridinium Chloride on Aqueous Surfaces of Sodium Chloride Solutions

    OpenAIRE

    Fujio, Katsuhiko; Hayashi, Koji; Suzuki, Maki

    2014-01-01

    Surface tension of aqueous NaCl solutions of tetradecylpyridinium chloride (TPC) has been measured by the drop weight method at different NaCl concentrations from 0 to 1.000 mol dm−3 at 25◦C. Surface excess densities of tetradecylpyridinium ion (TP+), Cl− and Na+ have been obtained as functions of TPC concentration at different NaCl concentrations by applying the Gibbs adsorption isotherm to the surface tension data below the critical micelle concentration (CMC) of TPC. Surface excess densiti...

  18. Adsorption of Dodecylpyridinium Chloride on Aqueous Surfaces of Sodium Chloride Solutions

    OpenAIRE

    Fujio, Katsuhiko; TAKEUCHI, Kumiko; Suzuki, Maki

    2012-01-01

    Surface tension of aqueous NaCl solutions of dodecylpyridinium chloride (DPC) has been measured by the drop weight method at different NaCl concentrations from 0 to 1.000 mol dm-3 at 25℃. Applying the Gibbs adsorption isotherm to the surface tension data at DPC concentrations below the critical micelle concentration (CMC), surface excess densities of dodecylpyridinium ion (DP+), Cl- and Na+ have been obtained as functions of DPC concentration at different NaCl concentrations. Surface excess d...

  19. Increased nitration and carbonylation of proteins in MRL +/+ mice exposed to trichloroethene: Potential role of protein oxidation in autoimmunity

    International Nuclear Information System (INIS)

    Even though reactive oxygen and nitrogen species (RONS) are implicated as mediators of autoimmune diseases (ADs), little is known about contribution of protein oxidation (carbonylation and nitration) in the pathogenesis of such diseases. The focus of this study was, therefore, to establish a link between protein oxidation and induction and/or exacerbation of autoimmunity. To achieve this, female MRL +/+ mice were treated with trichloroethene (TCE), an environmental contaminant known to induce autoimmune response, for 6 or 12 weeks (10 mmol/kg, i.p., every 4th day). TCE treatment resulted in significantly increased formation of nitrotyrosine (NT) and induction of iNOS in the serum at both 6 and 12 weeks of treatment, but the response was greater at 12 weeks. Likewise, TCE treatment led to greater NT formation, and iNOS protein and mRNA expression in the livers and kidneys. Moreover, TCE treatment also caused significant increases (∼3 fold) in serum protein carbonyls (a marker of protein oxidation) at both 6 and 12 weeks. Significantly increased protein carbonyls were also observed in the livers and kidneys (2.1 and 1.3 fold, respectively) at 6 weeks, and to a greater extent at 12 weeks (3.5 and 2.1 fold, respectively) following TCE treatment. The increases in TCE-induced protein oxidation (carbonylation and nitration) were associated with significant increases in Th1 specific cytokine (IL-2, IFN-γ) release into splenocyte cultures. These results suggest an association between protein oxidation and induction/exacerbation of autoimmune response. The results present a potential mechanism by which oxidatively modified proteins could contribute to TCE-induced autoimmune response and necessitates further investigations for clearly establishing the role of protein oxidation in the pathogenesis of ADs.

  20. 7,7′-Bis[(aza-18-crown-6)carbonyl]thioindigo: Synthesis, Experimental, Theoretical Characterization and Biological Activities

    OpenAIRE

    Koparır, Metin

    2013-01-01

    This work presents the characterization of 7,7'-Bis[(aza-18-crown-6)carbonyl]thioindigo (I) by quantum chemical calculations and spectral techniques. The molecular geometry, frontier molecular orbitals (FMO), molecular electrostatic potentials (MEP) and nonlinear optical properties of I in the ground state have been calculated using the density functional method (B3LYP) with the 6−31G(d,p) basis set. The calculated results show that the optimized geometry can well reproduce the crystal struct...

  1. A NOVEL COPOLYMER-BOUND CIS- DICARBONYLRHODIUM COMPLEX FOR THE CARBONYLATION OF METHANOL TO ACETIC ACID AND ACETIC ANHYDRIDE

    Institute of Scientific and Technical Information of China (English)

    YUAN Guoqing; CHEN Yuying; CHEN Rongyao

    1989-01-01

    A series of porous microspheres of linear and ethylene diacrylate (M ') cross-linked copolymers of 2 - vinylpyridine (V) and methyl acrylate (M) reacted with tetracarbonyldichlorodirhodium to form a series of cis-dicarbonylrhodium chelate complex (MVRh and MVM 'Rh). They are thermally stable yet very reactive in the carbonylation of methanol to acetic acid, and of methanol - acetic acid mixture to acetic acid and acetic anhydride with a selectivity of 100% under relatively mild and anhydrous conditions.

  2. Binding of the 9-O-N-aryl/arylalkyl amino carbonyl methyl substituted berberine analogs to tRNA(phe..

    Directory of Open Access Journals (Sweden)

    Anirban Basu

    Full Text Available BACKGROUND: Three new analogs of berberine with aryl/ arylalkyl amino carbonyl methyl substituent at the 9-position of the isoquinoline chromophore along with berberrubine were studied for their binding to tRNA(phe by wide variety of biophysical techniques like spectrophotometry, spectrofluorimetry, circular dichroism, thermal melting, viscosity and isothermal titration calorimetry. METHODOLOGY/ PRINCIPAL FINDINGS: Scatchard binding isotherms revealed that the cooperative binding mode of berberine was propagated in the analogs also. Thermal melting studies showed that all the 9-O-N-aryl/arylalkyl amino carbonyl methyl substituted berberine analogs stabilized the tRNA(phe more in comparison to berberine. Circular dichroism studies showed that these analogs perturbed the structure of tRNA(phe more in comparison to berberine. Ferrocyanide quenching studies and viscosity results proved the intercalative binding mode of these analogs into the helical organization of tRNA(phe. The binding was entropy driven for the analogs in sharp contrast to the enthalpy driven binding of berberine. The introduction of the aryl/arylalkyl amino carbonyl methyl substituent at the 9-position thus switched the enthalpy driven binding of berberine to entropy dominated binding. Salt and temperature dependent calorimetric studies established the involvement of multiple weak noncovalent interactions in the binding process. CONCLUSIONS/ SIGNIFICANCE: The results showed that 9-O-N-aryl/arylalkyl amino carbonyl methyl substituted berberine analogs exhibited almost ten folds higher binding affinity to tRNA(phe compared to berberine whereas the binding of berberrubine was dramatically reduced by about twenty fold in comparison to berberine. The spacer length of the substitution at the 9-position of the isoquinoline chromophore appears to be critical in modulating the binding affinities towards tRNA(phe.

  3. Evaluation of Ternary Mobile Phases for the Analysis of Carbonyl Compound Derivatives Using High-Performance Liquid Chromatography

    OpenAIRE

    Duy Xuan Ho; Ki-Hyun Kim

    2011-01-01

    In this study, the feasibility of ternary mobile phases was examined in a high-performance liquid chromatography (HPLC)-based analysis of carbonyl compounds (CCs). To test the performance of different ternary phases, the liquid phase standards containing a 15 aldehyde/ketone-DNPH(o) mix were analyzed through a series of five-point calibration experiments. For this comparison, three types of ternary mobile phases were prepared initially by mixing water (W) with two of the following three organ...

  4. A palladium-catalyzed intramolecular carbonylative annulation reaction for the synthesis of 4,5-fused tricyclic 2-quinolones.

    Science.gov (United States)

    Zhang, Xiwu; Liu, Haichao; Jia, Yanxing

    2016-06-01

    A concise and efficient synthetic route to 4,5-fused tricyclic 2-quinolones through the palladium-catalyzed carbonylative annulation of alkyne-tethered N-substituted o-iodoanilines has been developed. This reaction proceeds smoothly under mild reaction conditions and exhibits exceptional tolerance to a variety of functional groups. It has been successfully applied to the efficient synthesis of BI 224436, an HIV integrase inhibitor. PMID:27225232

  5. AgOTf-catalyzed one-pot reactions of 2-alkynylbenzaldoximes with α,β-unsaturated carbonyl compounds

    Directory of Open Access Journals (Sweden)

    Qiuping Ding

    2013-09-01

    Full Text Available AgOTf-catalyzed one-pot reactions of 2-alkynylbenzaldoximes with various α,β-unsaturated carbonyl compounds under mild conditions are described, which provides a facile and efficient pathway for the synthesis of 1-alkylated isoquinoline derivatives. The method tolerates a wide range of substrates and allows for the preparation of the products of interest in moderate to excellent yields.

  6. Acetalization of Carbonyl Compounds as Pentaerythritol Diacetals and Diketals in the Presence of Cellulose Sulfuric Acid as an Efficient, Biodegradable and Reusable Catalyst

    Institute of Scientific and Technical Information of China (English)

    Shaterian, Hamid Reza; Rigi, Fatemeh

    2012-01-01

    This paper reports a practical and green method for the acetalization of carbonyl compounds as pentaerythritol diacetals and diketals derivatives using cellulose sulfuric acid as a biodegradable and reusable solid acid catalyst under thermal solvent-free conditions.

  7. Reactivity, Selectivity, and Reaction Mechanisms of Aminoguanidine, Hydralazine, Pyridoxamine, and Carnosine as Sequestering Agents of Reactive Carbonyl Species: A Comparative Study.

    Science.gov (United States)

    Colzani, Mara; De Maddis, Danilo; Casali, Gaia; Carini, Marina; Vistoli, Giulio; Aldini, Giancarlo

    2016-08-19

    Reactive carbonyl species (RCS) are endogenous or exogenous byproducts involved in the pathogenic mechanisms of different oxidative-based disorders. Detoxification of RCS by carbonyl quenchers is a promising therapeutic strategy. Among the most studied quenchers are aminoguanidine, hydralazine, pyridoxamine, and carnosine; their quenching activity towards four RCS (4-hydroxy-trans-2-nonenal, methylglyoxal, glyoxal, and malondialdehyde) was herein analyzed and compared. Their ability to prevent protein carbonylation was evaluated in vitro by using an innovative method based on high-resolution mass spectrometry (HRMS). The reactivity of the compounds was RCS dependent: carnosine efficiently quenched 4-hydroxy-trans-2-nonenal, pyridoxamine was particularly active towards malondialdehyde, aminoguanidine was active towards methylglyoxal and glyoxal, and hydralazine efficiently quenched all RCS. Reaction products were generated in vitro and were characterized by HRMS. Molecular modeling studies revealed that the reactivity was controlled by specific stereoelectronic parameters that could be used for the rational design of improved carbonyl quenchers. PMID:26891408

  8. Effects of low concentration biodiesel blends application on modern passenger cars. Part 2: Impact on carbonyl compound emissions

    Energy Technology Data Exchange (ETDEWEB)

    Fontaras, Georgios [Laboratory of Applied Thermodynamics, Aristotle University Thessaloniki, P.O. Box 458, GR 54124 Thessaloniki (Greece); Karavalakis, Georgios [Laboratory of Fuels Technology and Lubricants, National Technical University of Athens, 9 Iroon Polytechniou Str., Zografou Campus, 15780 Athens (Greece); Kousoulidou, Marina; Ntziachristos, Leonidas [Laboratory of Applied Thermodynamics, Aristotle University Thessaloniki, P.O. Box 458, GR 54124 Thessaloniki (Greece); Bakeas, Evangelos [Laboratory of Analytical Chemistry, Chemistry Department, National and Kapodistrian University of Athens (Greece); Stournas, Stamoulis [Laboratory of Fuels Technology and Lubricants, National Technical University of Athens, 9 Iroon Polytechniou Str., Zografou Campus, 15780 Athens (Greece); Samaras, Zissis, E-mail: zisis@auth.g [Laboratory of Applied Thermodynamics, Aristotle University Thessaloniki, P.O. Box 458, GR 54124 Thessaloniki (Greece)

    2010-07-15

    Today in most European member states diesel contains up to 5% vol biodiesel. Since blending is expected to increase to 10% vol, the question arises, how this higher mixing ratio will affect tailpipe emissions particularly those linked to adverse health effects. This paper focuses on the impact of biodiesel on carbonyl compound emissions, attempting also to identify possible relationship between biodiesel feedstock and emissions. The blends were produced from five different feedstocks, commonly used in Europe. Measurements were conducted on a Euro 3 common-rail passenger car over various driving cycles. Results indicate that generally the use of biodiesel at low concentrations has a minor effect on carbonyl compound emissions. However, certain biodiesels resulted in significant increases while others led to decreases. Biodiesels associated with increases were those derived from rapeseed oil (approx. 200%) and palm oil (approx. 180%), with the highest average increases observed at formaldehyde and acroleine/acetone. - Biodiesel application, may increase the levels of certain pollutants such as carbonyl compounds which are associated with both environmental and health risks.

  9. Observing the Transition from Equatorial to Axial CO Chemisorption: Infrared Photodissociation Spectroscopy of Yttrium Oxide-Carbonyls.

    Science.gov (United States)

    Xie, Hua; Liu, Zhiling; Zhao, Zhi; Kong, Xiangtao; Fan, Hongjun; Tang, Zichao; Jiang, Ling

    2016-06-01

    A series of yttrium oxide-carbonyls are prepared via a laser vaporization supersonic cluster source in the gas phase and identified by mass-selected infrared photodissociation (IRPD) spectroscopy in the C-O stretching region and by comparing the observed IR spectra with those from quantum chemical calculations. For YO(CO)4(+), all four CO ligands prefer to occupy the equatorial site of the YO(+) unit, leading to a quadrangular pyramid with C4v symmetry. Two energetically nearly degenerate isomers are responsible for YO(CO)5(+), in which the fifth CO ligand is either inserted into the equatorial plane of YO(CO)4(+) or coordinated opposite the oxygen on the C4 axis. YO(CO)6(+) has a pentagonal bipyramidal structure with C5v symmetry, which includes five equatorial CO ligands and one axial CO ligand. The present IRPD spectroscopic and theoretical study of YO(CO)n(+) extends the first shell coordination number of CO ligands in metal monoxide carbonyls to six. The transition from equatorial to axial CO chemisorption in these yttrium oxide-carbonyls is fortunately observed at n = 5, providing new insight into ligand interactions and coordination for the transition metal oxides. PMID:27158889

  10. Nickel Chloride Promoted Glaser Coupling Reaction in Hot Water

    Institute of Scientific and Technical Information of China (English)

    Pin Hua LI; Lei WANG; Min WANG; Jin Can YAN

    2004-01-01

    A Glaser coupling reaction of terminal alkynes in the presence of nickel chloride without any organics and bases in hot water has been developed, which produces the corresponding homo-coupling products in good yields.

  11. Methyltrioctylammonium chloride catalysed sonochemical synthesis of acridine diones

    Indian Academy of Sciences (India)

    Bhupinder Kaur; Harish Kumar

    2013-09-01

    The greener, clean and efficient protocol for the synthesis of acridine diones derivatives has been achieved by reacting aromatic aldehyde, dimedone and amines using methyltrioctylammonium chloride (Aliquate 336) as a catalyst under ultrasonic irradiations.

  12. Use of saturated sodium chloride solution as a tissue fixative

    Directory of Open Access Journals (Sweden)

    A. Al-Saraj

    2010-01-01

    Full Text Available The present study was carried out to examine the capability of saturated sodium chloride solution as a fixative agent instead of formalin which is regarded as a carcinogenic material. For this purpose 3 rabbits were used and their livers, kidneys and spleens were exposed and removed. Neutral buffered formalin solution, saturated sodium chloride solution and distilled water were used as fixatives for specimens obtained from the first, second and third rabbits respectively. Routine histological technique was performed to prepare a stained histological sections for light microscopic examination. The result showed that the tissue sections which were obtained by using sodium chloride have the same histological features and without any artifacts when they compared with the results obtained using formalin fixation method. We conclude that the saturated sodium chloride solution can be used as a fixative agent in some circumstances when no any fixative agent is available.

  13. Thermodynamic calculation of self-diffusion in sodium chloride

    Science.gov (United States)

    Zhang, Baohua; Li, Chengbo; Shan, Shuangming

    2016-05-01

    Using the available pressure-volume-temperature equation of state of sodium chloride, we show that the self-diffusion coefficients of sodium and chloride in sodium chloride as a function of temperature and pressure can be successfully reproduced in terms of bulk elastic and expansivity data. We use a thermodynamic model that interconnects point-defect parameters with bulk properties. Our calculated diffusion coefficients and point-defect parameters, including activation enthalpy, activation entropy, and activation volume, well agree with reported experimental results when uncertainties are considered. Furthermore, the ionic conductivity of sodium chloride inferred from our predicted diffusivities of sodium through the Nernst-Einstein equation is compared with previous experimental data.

  14. Catalytic Decomposition of Methylene Chloride by Sulfated Titania Catalysts

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Catalytic decomposition of methylene chloride in air below 300℃ was studied.Sulfated titania was very effective in converting 959ppm methylene chloride selectively to CO,CO2 and HCl.Complete decomposition of methylene chloride was achieved at low temperature(275℃).It was found that the acidic property of catalyst was a determinant factor for the catalytic activity.The presence of water vapor in the feed stream remarkably reduced the catalytic activity,which could be due to the blockage of acidic sites on the surface of catalyst by water molecules.A bifunctional catalyst comprising copper oxide was developed to improve the selectivity of catalytic oxidation,which indicated that copper oxide can promote the deep oxidation of methylene chloride.The crystal form of TiO2 imposes an important influence upon the catalytic oxidation.

  15. Chloride supporting electrolytes for all-vanadium redox flow batteries.

    Science.gov (United States)

    Kim, Soowhan; Vijayakumar, M; Wang, Wei; Zhang, Jianlu; Chen, Baowei; Nie, Zimin; Chen, Feng; Hu, Jianzhi; Li, Liyu; Yang, Zhenguo

    2011-10-28

    This paper examines vanadium chloride solutions as electrolytes for an all-vanadium redox flow battery. The chloride solutions were capable of dissolving more than 2.3 M vanadium at varied valence states and remained stable at 0-50 °C. The improved stability appeared due to the formation of a vanadium dinuclear [V(2)O(3)·4H(2)O](4+) or a dinuclear-chloro complex [V(2)O(3)Cl·3H(2)O](3+) in the solutions over a wide temperature range. The all-vanadium redox flow batteries with the chloride electrolytes demonstrated excellent reversibility and fairly high efficiencies. Only negligible, if any, gas evolution was observed. The improved energy capacity and good performance, along with the ease in heat management, would lead to substantial reduction in capital cost and life-cycle cost, making the vanadium chloride redox flow battery a promising candidate for stationary applications. PMID:21922094

  16. Purification and reconstitution of chloride channels from kidney and trachea

    International Nuclear Information System (INIS)

    Chloride channels mediate absorption and secretion of fluid in epithelia, and the regulation of these channels is now known to be defective in cystic fibrosis. Indanyl-oxyacetic acid 94 (IAA-94) is a high-affinity ligand for the chloride channel, and an affinity resin based on that structure was developed. Solubilized proteins from kidney and trachea membranes were applied to the affinity matrix, and four proteins with apparent molecular masses of 97, 64, 40, and 27 kilodaltons were eluted from the column by excess IAA-94. A potential-dependent 36Cl- uptake was observed after reconstituting these proteins into liposomes. Three types of chloride channels with single-channel conductances of 26, 100, and 400 picosiemens were observed after fusion of these liposomes with planar lipid bilayers. Similar types of chloride channels have been observed in epithelia

  17. Stochastic modeling of reinforced concrete structures exposed to chloride attack

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Frier, Christian

    2004-01-01

    For many reinforced concrete structures corrosion of reinforcement is an important problem since it can result in expensive maintenance and repair actions. Further, a significant reduction of the load-bearing capacity can occur. One mode of corrosion initiation is that the chloride content around...... the reinforcement exceeds a critical threshold value. In the present paper a stochastic model is described by which the chloride content in a reinforced concrete structure can be estimated. The chloride ingress is modeled by a 2-dimensional diffusion process and the diffusion coefficient, surface chloride...... concentration and reinforcement cover depth are modeled by stochastic fields. The paper contains a description of the parameters to be included in a stochastic model and a proposal for the information needed to obtain values for the parameters in order to be able to perform reliability investigations...

  18. Chloride supporting electrolytes for all-vanadium redox flow batteries.

    Science.gov (United States)

    Kim, Soowhan; Vijayakumar, M; Wang, Wei; Zhang, Jianlu; Chen, Baowei; Nie, Zimin; Chen, Feng; Hu, Jianzhi; Li, Liyu; Yang, Zhenguo

    2011-10-28

    This paper examines vanadium chloride solutions as electrolytes for an all-vanadium redox flow battery. The chloride solutions were capable of dissolving more than 2.3 M vanadium at varied valence states and remained stable at 0-50 °C. The improved stability appeared due to the formation of a vanadium dinuclear [V(2)O(3)·4H(2)O](4+) or a dinuclear-chloro complex [V(2)O(3)Cl·3H(2)O](3+) in the solutions over a wide temperature range. The all-vanadium redox flow batteries with the chloride electrolytes demonstrated excellent reversibility and fairly high efficiencies. Only negligible, if any, gas evolution was observed. The improved energy capacity and good performance, along with the ease in heat management, would lead to substantial reduction in capital cost and life-cycle cost, making the vanadium chloride redox flow battery a promising candidate for stationary applications.

  19. Solidification of spent TBP solvent with aluminium chloride compounds

    International Nuclear Information System (INIS)

    The new techniques for processing spent TBP was investigated. It was proved that treatment of TBP containing DBP with aluminium chloride resulted in the formation of aluminium phosphate suitable for long term storage and final disposal

  20. Reinforcement corrosion in alkaline chloride media with reduced oxygen concentrations

    International Nuclear Information System (INIS)

    It is commonly considered that the corrosion of steel in concrete is controlled by the oxygen content of the pore solution and there are service life models that relate the corrosion rate to the amount of oxygen. It is also commonly believed that in water saturated conditions the oxygen content in the pores is negligible and that underwater there is no risk of depassivation and the corrosion rate is very low. However, the available data on corrosion rates in immersed conditions do not indicate such performance; on the contrary corrosion develops when sufficient chloride reaches the reinforcement. In the present paper, results are presented for tests performed in alkaline chloride solutions that were purged with nitrogen to reduce the oxygen content. The results indicate that at very low oxygen concentrations, corrosion may develop in the presence of chlorides. The presence or absence of corrosion is influenced by the amount of chloride, the corrosion potential and the steel surface condition. (authors)

  1. Chlorides behavior in raw fly ash washing experiments

    Energy Technology Data Exchange (ETDEWEB)

    Zhu Fenfen, E-mail: zhu@hse.gcoe.kyoto-u.ac.jp [Department of Urban and Environmental Engineering, Graduate School of Engineering, Katsura Campus, Kyoto University, Nishikyo-ku, Kyoto 615-8540 (Japan); Takaoka, Masaki; Oshita, Kazuyuki [Department of Urban and Environmental Engineering, Graduate School of Engineering, Katsura Campus, Kyoto University, Nishikyo-ku, Kyoto 615-8540 (Japan); Kitajima, Yoshinori; Inada, Yasuhiro [High Energy Accelerator Research Organization (KEK), Institute of Material Structure Science (IMSS), Oho 1-1, Tsukuba, Ibaraki 305-0801 (Japan); Morisawa, Shinsuke; Tsuno, Hiroshi [Department of Urban and Environmental Engineering, Graduate School of Engineering, Katsura Campus, Kyoto University, Nishikyo-ku, Kyoto 615-8540 (Japan)

    2010-06-15

    Chloride in fly ash from municipal solid waste incinerators (MSWIs) is one of the obstructive substances in recycling fly ash as building materials. As a result, we have to understand the behavior of chlorides in recycling process, such as washing. In this study, we used X-ray absorption near edge structure (XANES) and X-ray diffraction (XRD) to study the chloride behavior in washed residue of raw fly ash (RFA). We found that a combination of XRD and XANES, which is to use XRD to identify the situation of some compounds first and then process XANES data, was an effective way to explain the chlorides behavior in washing process. Approximately 15% of the chlorine in RFA was in the form of NaCl, 10% was in the form of KCl, 51% was CaCl{sub 2}, and the remainder was in the form of Friedel's salt. In washing experiments not only the mole percentage but also the amount of soluble chlorides including NaCl, KCl and CaCl{sub 2} decreases quickly with the increase of liquid to solid (L/S) ratio or washing frequency. However, those of insoluble chlorides decrease slower. Moreover, Friedel's salt and its related compound (11CaO.7Al{sub 2}O{sub 3}.CaCl{sub 2}) were reliable standards for the insoluble chlorides in RFA, which are strongly related to CaCl{sub 2}. Washing of RFA promoted the release of insoluble chlorides, most of which were in the form of CaCl{sub 2}.

  2. Determination of chloride in geological samples by ion chromatography

    Science.gov (United States)

    Wilson, S.A.; Gent, C.A.

    1983-01-01

    Samples of silicate rocks are prepared by sodium carbonate fusion and then treated by ion chromatography. The method was tested for geological standards with chloride concentration between 0.003 and 3%. Observed chloride concentrations comparedd favorably with literature values. The relative standard deviation and detection limit for the method were 8% and 7 ppm, respectively. Up to 30 determination per 24-hour period were possible. ?? 1983.

  3. Optical Studies on Sol-Gel Derived Lead Chloride Crystals

    OpenAIRE

    Rejeena, I; Lillibai, B; Nithyaja, B; Nampoori, P.N V; P. Radhakrishnan

    2013-01-01

    Optical characterization of lead chloride crystals prepared by sol-gel method is reported. The relevant sol-gel technique is used for the preparation of PbCl2 samples with five different types. In this paper, we report the absorption and fluorescence behaviour of pure, UV& IR irradiated and electric & magnetic field applied lead chloride crystal samples in solution phase at two different concentrations. Optical bandgap and emission studies of these crystals are also done.

  4. Macrocycle Synthesis by Chloride-Templated Amide Bond Formation.

    Science.gov (United States)

    Martí-Centelles, Vicente; Burguete, M Isabel; Luis, Santiago V

    2016-03-01

    A new family of pseudopeptidic macrocyclic compounds has been prepared involving an anion-templated amide bond formation reaction at the macrocyclization step. Chloride anion was found to be the most efficient template in the macrocyclization process, producing improved macrocyclization yields with regard to the nontemplated reaction. The data suggest a kinetic effect of the chloride template, providing an appropriate folded conformation of the open-chain precursor and reducing the energy barrier for the formation of the macrocyclic product. PMID:26820908

  5. cis-Dichloridobis(1,10-phenanthrolinechromium(III chloride

    Directory of Open Access Journals (Sweden)

    Xiaoli Gao

    2011-02-01

    Full Text Available In the title complex, [CrCl2(C12H8N22]Cl, the CrIII ion is situated on a twofold rotation axis and displays a slightly distorted octahedral CrCl2N4 coordination geometry. The Cr environment is composed of a cis arrangement of two 1,10-phenanthroline and two chloride ligands. The chloride counter-anion exhibits half-occupation and is equally disordered over two positions.

  6. Recovering germanium from coal ash by chlorination with ammonium chloride

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A new process of enriching germanium from coal ash was developed. The process involves in mixing the coal ash and ammonium chloride and then roasting the mixture to produce germanium chloride that is then absorbed by dilute hydrochloric acid and hydrolyzed to germanium oxide. The germanium recovery reached to 80.2% at the optimum condition: mass ratio of NH4Cl/coal ash is 0.15, roasting temperature 400℃ and roasting time 90 min.

  7. Aqueous Chloride Operations Overview: Plutonium and Americium Purification/Recovery

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, Kyle Shelton [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kimball, David Bryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Skidmore, Bradley Evan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-09-28

    These are a set of slides intended for an information session as part of recruiting activities at Brigham Young University. It gives an overview of aqueous chloride operations, specifically on plutonium and americium purification/recovery. This presentation details the steps taken perform these processes, from plutonium size reduction, dissolution, solvent extraction, oxalate precipitation, to calcination. For Americium recovery, it details the CLEAR (chloride extraction and actinide recovery) Line, oxalate precipitation and calcination.

  8. Effect of kaolin treatment temperature on mortar chloride permeability

    OpenAIRE

    Puertas, F.; Mejía de Gutiérrez, R.; J. Torres

    2007-01-01

    The present paper discusses the results of chloride resistance tests conducted on ordinary Portland cement (OPC) mortars containing a Colombian kaolin pre-treated at temperatures of from 600 to 800 ºC. The resulting metakaolin (MK) was added to OPC mortar mixes in proportions of 10 and 20% by cement weight. The mortars were compared for physical and chemical properties, including capillary absorption, chloride permeability and pore microstructure as assessed by mercury porosimetry....

  9. Extraction and immobilization of simulated pyrometallurgical chloride waste in Zeolite

    International Nuclear Information System (INIS)

    Zeolites are effective media for the removal and immobilization of fission products waste from pyrometallurgical reprocessing of nuclear fuels. In the present study, equilibration experiments between zeolite 4A and a simulated: pyrometallurgical chloride waste were carried out. Several batches of equilibration were carried out by varying the zeolite to salt (Z/S) ratio. The effects of Z/S on the extraction behaviour of the waste chloride salts were explored. (author)

  10. The effect of chloride and sulfate on Completely Recyclable Concrete

    OpenAIRE

    Arvaniti, E.; De Schepper, M.; De Belie, N.; De Buysser, K.; Van Driessche, I.

    2013-01-01

    Completely Recyclable Concrete (CRC) is intended to be recycled as raw material within the cement production from a predesign stage. However, concrete contributions that are exposed to aggressive environments (e.g. industrial and seaside buildings), could carry elements such as chlorides, sulfur and alkalis after demolition, which will end up in the recycled material. The aim of this study is to better understand the influence of chloride and sulfur in CRC on the final clinker properties. The...

  11. Hafnium extraction from acidic chloride solutions by Cyanex 923

    Energy Technology Data Exchange (ETDEWEB)

    El-Ammouri, E.; Distin, P.A. [McGill Univ., Montreal (Canada)

    1996-08-01

    Hafnium extraction from hydrochloric acid/lithium chloride solutions into Cyanex 923 in kerosene has been studied. Variables investigated were hydrochloric acid, total chloride and hafnium concentrations in the aqueous phase, and extractant/modifier (isodecanol) levels in the organic phase. Hafnium is considered to load as the tetrachloride complex forming a disolvate with Cyanex 923. Results are compared with equivalent data for zirconium extraction. 14 refs., 7 figs., 2 tabs.

  12. Intracellular chloride concentration of the mouse vomeronasal neuron

    OpenAIRE

    Kim, Sangseong; Ma, Limei; Unruh, Jay; McKinney, Sean; Yu, C. Ron

    2015-01-01

    Background The vomeronasal organ (VNO) is specialized in detecting pheromone and heterospecific cues in the environment. Recent studies demonstrate the involvement of multiple ion channels in VNO signal transduction, including the calcium-activated chloride channels (CACCs). Opening of CACCs appears to result in activation of VNO neuron through outflow of Cl− ions. However, the intracellular Cl− concentration remains undetermined. Results We used the chloride ion quenching dye, MQAE, to measu...

  13. Computational modelling of chloride ion transport in reinforced concrete

    OpenAIRE

    Meijers, S.J.H.; Bijen, J.M.J.M.; De Borst, R.; Fraaij, A.L.A.

    2001-01-01

    Exposure to a saline environment is a major threat with respect to the durability of reinforced concrete structures. The chloride ions, which are present in seawater and de-icing salts, are able to penetrate the concrete up to the depth of the reinforcement. They can eventually trigger a pitting corrosion process. The assessment of a corrosion-free service life of concrete structures is of paramount economic interest. However, the modelling of the ingress of chloride ions is complicated due t...

  14. Large Scale Synthesis of Carbon Nanofibres on Sodium Chloride Support

    OpenAIRE

    Ravindra Rajarao; Badekai Ramachandra Bhat

    2012-01-01

    Large scale synthesis of carbon nanofibres (CNFs) on a sodium chloride support has been achieved. CNFs have been synthesized using metal oxalate (Ni, Co and Fe) as catalyst precursors at 680 C by chemical vapour deposition method. Upon pyrolysis, this catalyst precursors yield catalyst nanoparticles directly. The sodium chloride was used as a catalyst support, it was chosen because of its non‐toxic and water soluble nature. Problems, such as the detrimental effect of CNFs, the detrimental ef...

  15. Durability Analysis of Subway Station in Chloride Environment

    OpenAIRE

    Yang LuFeng; Yu Bo; Hong Bin

    2013-01-01

    In this study, a finite element model for chloride ions transport in saturated concrete was proposed based on the Fick’s second law of diffusion. The governing partial differential equation was solved numerically in space as a boundary-value problem and in time as an initial-value problem by means of the finite element formulations. The maximum allowable value of chloride diffusion coefficient within different locations of subway station with service life of 100a was achieved and suggestions ...

  16. Influence of cracks on chloride penetration in concrete

    OpenAIRE

    Audenaert, K.; Schutter, G. de; MARSAVINA, L

    2009-01-01

    Chloride initiated reinforcement corrosion is the main durability problem for concrete structures in a marine environment. If the chlorides reach the reinforcement steel, it will depassivate and start to corrode in presence of air and water. Since the corrosion products have a larger volume than the initial products, concrete stresses are induced, leading to spalling and degradation of the concrete structures. If cracks, caused by early drying, thermal effects, shrinkage movements or overstre...

  17. Chloride ion transport performance in slag mortar under fatigue loading

    Institute of Scientific and Technical Information of China (English)

    WANG CaiHui; SUN Wei; JIANG JinYang; HAN JianDe; YE BangTu

    2012-01-01

    The transport performance of chloride ion in slag cement mortar was investigated experimentally.In the self-designed experiment,fatigue loading was coupled simultaneously with ion transportation process,the diffusion law of chloride ion was obtained by titration and the AE (acoustic emission) technique was employed to detect the real-time damage distribution in the mortar specimen.The results for fatigue stress levels of 0.3,0.4 and 0.5 and slag contents of 0,10%,30% and 50% showed that fatigue loading accelerated the diffusion of chloride ion in mortar and the acceleration effect increased with the increase in stress levels.Slag addition was found to improve anti-chloride ion erosion performance effectively with the best substitution level at 30%,because the inhibition effect of slag on chloride ion diffusion diminished when the slag content exceeded 30%.The comparative experiments indicated that dynamic load has a significant effect on the transport performance of chloride ion in slag cement mortar.

  18. Removal of chloride from electric arc furnace dust.

    Science.gov (United States)

    Chen, Wei-Sheng; Shen, Yun-Hwei; Tsai, Min-Shing; Chang, Fang-Chih

    2011-06-15

    Electric arc furnace (EAF) dust with high chloride content increases the threat of dioxin emissions and the high chloride content reduces the value of recycled zinc oxide produced by EAF dust recycling plants. This study conducts a number of laboratory experiments to determine the technical feasibility of a new dechlorination method. These methods consist of a series of roasting processes and water washing processes. In the roasting process, EAF dust was heated in a tube furnace to evaluate the parameters of atmospheric conditions, roasting temperature, and roasting time. Results indicate that sulfation roasting is more efficient in reducing chloride content than other roasting processes. The water washing process can totally remove water-soluble chloride at a solid to liquid ratio of 1:10. However, the remaining water-insoluble substance is difficult to dechlorinate. For example, lead chloride forms a hydroxyl-halide (PbOHCl) and lead chloride carbonate (Pb(2)CO(3)Cl(2)) agglutinative matrix that is hard to wash away.

  19. Congenital chloride diarrhea: a review of twelve Arabian children

    Directory of Open Access Journals (Sweden)

    Elrefae F

    2013-06-01

    Full Text Available Fawaz Elrefae,1 Ahmed Farag Elhassanien,2 Hesham Abdel-Aziz Alghiaty3 1Pediatric Gastroenterology, Al-Adan Hospital, Kuwait; 2Faculty of Medicine, Elmansoura University, El Mansoura, El Dakahleya, Egypt; 3Faculty of Medicine, Benha University, Egypt Background: Congenital chloride diarrhea (CCD, a rare autosomal recessive disorder, is characterized by sustained watery diarrhea (due to defect of active Chloride/HCO3 exchange in the ileum and colon with high fecal chloride. Objective: To spotlight the common presentation of CCD for early management and prevention of complications. Subjects and methods: This is a retrospective case series study of patients diagnosed as CCD who were followed up in the pediatric department of Al-Adan Hospital, Kuwait. Results: Twelve patients diagnosed with CCD were born to consanguineous parents; had antenatal history of intrauterine growth retardation (IUGR; polyhydramnios; and distended hypoechoic fetal bowel; and presented with abdominal distension, hypotonia and muscle wasting. 90% of patients had maternal hypertension and 75% of patients had absence of normal meconium at birth. Our patients showed a decrease in serum sodium, potassium, chloride and urine chloride. Conclusion: A high level of suspicion for an early diagnosis of CCD should be considered for any infant presenting with chronic diarrhea, especially in the presence of consanguineous marriage, and the characteristic features in antenatal ultrasound. Thus, allowing for early investigations and appropriate management. Keywords: congenital chloride diarrhea, children, chronic diarrhea, metabolic alkalosis, prenatal diagnosis

  20. Stabilizing Plutonium oxide material containing Chloride salts at PFP

    International Nuclear Information System (INIS)

    PFP had over 900 items, weighing more than 1100 kg consisting of impure plutonium oxides referred to as high chloride content plutonium oxides. Tests were conducted to examine items for physical characteristics. After 17 years of storage, the inner food-pack cans maintained integrity with very little evidence of corrosion. Items were washed with water to remove chloride salts. Chloride was readily soluble with plutonium concentrations less than 0.05 g/L in wash solution from all but one of seven items. Washed material was calcined at 1000 C. The calcined material passed the storage test for less than 0.5% water. Unopened items were examined using gamma energy analysis to determine if a prompt gamma (n, x) interaction could be used to screen out items with low chloride concentrations. The prompt gamma was not measurable. A 2168 keV gamma from the (α, x) interaction with chloride correlated within 10% of the chloride concentration measured from washing the item with water

  1. DEVELOPMENTAL TOXICITY OF COPPER CHLORIDE, METHYLENE CHLORIDE,AND 6-AMINONICOTINAMIDE TO EMBRYOS OF THE GRASS SHRIMPPALAEMONETES PUGIO

    Science.gov (United States)

    Embryos of estuarine grass shrimp Palaemonetes pugio have demonstrated sensitivity to various solvents and petroleum products, indicating utility for evaluating estuarine contamination. Testing was performed to establish concentration-response curves for methylene chloride, cop...

  2. A small synthetic molecule functions as a chloride-bicarbonate dual-transporter and induces chloride secretion in cells.

    Science.gov (United States)

    Liu, Peng-Yun; Li, Shing-To; Shen, Fang-Fang; Ko, Wing-Hung; Yao, Xiao-Qiang; Yang, Dan

    2016-05-31

    A C2 symmetric small molecule composed of l-phenylalanine and isophthalamide was found to function as a Cl(-)/HCO3(-) dual transporter and self-assemble into chloride channels. In Ussing-chamber based short-circuit current measurements, this molecule elicited chloride-dependent short-circuit current (Isc) increase in both Calu-3 cell and CFBE41o-cell (with F508del mutant CFTR) monolayers. PMID:27188496

  3. Ab initio Investigations of the Equilibria between Trichlorothioacetyl Chloride, Tetrachlorothiirane, and Trichloroethenesulfenyl Chloride, their Reactants and Decomposition Products

    DEFF Research Database (Denmark)

    Pedersen, Kim Vestergaard; Christensen, Henrik; Shim, Irene;

    2004-01-01

    Trichlorothioacetyl chloride 1, tetrachlorothiirane 2, and trichloroethenesulfenyl chloride 3 and the equilibria between them have been investigated by ab initio Hartree-Fock (HF), Møller-Plesset second order perturbation (MP2) calculations, and by Gaussian-3 theory, G3(MP2). The transition state...... of the isomerization reactions have been identified. Also investigated were possible reactions leading to the isomers and their possible decomposition products. The results show that the unobserved isomerization reactions are feasible....

  4. Technical note: Could benzalkonium chloride be a suitable alternative to mercuric chloride for preservation of seawater samples?

    OpenAIRE

    Gloël, J.; Robinson, C.; Tilstone, G. H.; Tarran, G.; J. Kaiser

    2015-01-01

    Instrumental equipment unsuitable or unavailable for fieldwork as well as lack of ship space can necessitate the preservation of seawater samples prior to analysis in a shore-based laboratory. Mercuric chloride (HgCl2) is routinely used for such preservation, but its handling and subsequent disposal incur environmental risks and significant expense. There is therefore a strong motivation to find less hazardous alternatives. Benzalkonium chloride (BAC) has been used previousl...

  5. Technical Note: Could benzalkonium chloride be a suitable alternative to mercuric chloride for preservation of seawater samples?

    OpenAIRE

    Gloël, J.; Robinson, C.; Tilstone, G. H.; Tarran, G.; J. Kaiser

    2015-01-01

    Instrumental equipment unsuitable or unavailable for fieldwork as well as lack of ship space can necessitate the preservation of seawater samples prior to analysis in a shore-based laboratory. Mercuric chloride (HgCl2) is routinely used for such preservation, but its handling and subsequent disposal incur significant risks and expense. Benzalkonium chloride (BAC) has been used previously for freshwater samples. Here, we assess BAC as a less hazardous alterna...

  6. 40 CFR 61.63 - Emission standard for vinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... formation and purification: The concentration of vinyl chloride in each exhaust gas stream from any... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Emission standard for vinyl chloride... for Vinyl Chloride § 61.63 Emission standard for vinyl chloride plants. An owner or operator of...

  7. Eddy covariance carbonyl sulfide flux measurements with a quantum cascade laser absorption spectrometer

    Science.gov (United States)

    Gerdel, Katharina; Spielmann, Felix M.; Hammerle, Albin; Wohlfahrt, Georg

    2016-04-01

    Carbonyl sulfide (COS) is the most abundant sulfur containing trace gas present in the troposphere at concentrations of around 500 ppt. Recent interest in COS by the ecosystem-physiological community has been sparked by the fact that COS co-diffuses into plant leaves pretty much the same way as carbon dioxide (CO2) does, but in contrast to CO2, COS is not known to be emitted by plants. Thus uptake of COS by vegetation has the potential to be used as a tracer for canopy gross photosynthesis, which cannot be measured directly, however represents a key term in the global carbon cycle. Since a few years, quantum cascade laser absorption spectrometers (QCLAS) are commercially available with the precision, sensitivity and time response suitable for eddy covariance (EC) flux measurements. While there exist a handful of published reports on EC flux measurements in the recent literature, no rigorous investigation of the applicability of QCLAS for EC COS flux measurements has been carried out so far, nor have been EC processing and QA/QC steps developed for carbon dioxide and water vapor flux measurements within FLUXNET been assessed for COS. The aim of this study is to close this knowledge gap, to discuss critical steps in the post-processing chain of COS EC flux measurements and to devise best-practice guidelines for COS EC flux data processing. To this end we collected EC COS (and CO2, H2O and CO) flux measurements above a temperate mountain grassland in Austria over the vegetation period 2015 with a commercially available QCLAS. We discuss various aspects of EC data post-processing, in particular issues with the time-lag estimation between sonic anemometer and QCLAS signals and QCLAS time series detrending, as well as QA/QC, in particular flux detection limits, random flux uncertainty, the interaction of various processing steps with common EC QA/QC filters (e.g. detrending and stationarity tests), u*-filtering, etc.

  8. Indoor Air Quality Investigations on Particulate Matter, Carbonyls, and Tobacco Specific Nitrosamines

    Science.gov (United States)

    Frey, Sarah E.

    Americans spend upwards of 90% of their time indoors, hence indoor air quality (IAQ) and the impact of IAQ on human health is a major public health concern. IAQ can be negatively impacted by outdoor pollution infiltrating indoors, the emission of indoor pollutants, indoor atmospheric chemistry and poor ventilation. Energy saving measures like retrofits to seal the building envelope to prevent the leakage of heated or cooled air will impact IAQ. However, existing studies have been inconclusive as to whether increased energy efficiency is leading to detrimental IAQ. In this work, field campaigns were conducted in apartment homes in Phoenix, Arizona to evaluate IAQ as it relates to particulate matter (PM), carbonyls, and tobacco specific nitrosamines (TSNA). To investigate the impacts of an energy efficiency retrofit on IAQ, indoor and outdoor air quality sampling was carried out at Sunnyslope Manor, a city-subsidized senior living apartment complex. Measured indoor formaldehyde levels before the building retrofit exceeded reference exposure limits, but in the long term follow-up sampling, indoor formaldehyde decreased for the entire study population by a statistically significant margin. Indoor PM levels were dominated by fine particles and showed a statistically significant decrease in the long term follow-up sampling within certain resident subpopulations (i.e. residents who reported smoking and residents who had lived longer at the apartment complex). Additionally, indoor glyoxal and methylglyoxal exceeded outdoor concentrations, with methylglyoxal being more prevalent pre-retrofit than glyoxal, suggesting different chemical pathways are involved. Indoor concentrations reported are larger than previous studies. TSNAs, specifically N'-nitrosonornicotine (NNN), 4-(methyl-nitrosamino)-4-(3-pyridyl)-butanal (NNA) and 4-(methylnitrosoamino)-1-(3-pyridyl)-1-butanone (NNK) were evaluated post-retrofit at Sunnyslope Manor. Of the units tested, 86% of the smoking units and

  9. High winter ozone pollution from carbonyl photolysis in an oil and gas basin.

    Science.gov (United States)

    Edwards, Peter M; Brown, Steven S; Roberts, James M; Ahmadov, Ravan; Banta, Robert M; deGouw, Joost A; Dubé, William P; Field, Robert A; Flynn, James H; Gilman, Jessica B; Graus, Martin; Helmig, Detlev; Koss, Abigail; Langford, Andrew O; Lefer, Barry L; Lerner, Brian M; Li, Rui; Li, Shao-Meng; McKeen, Stuart A; Murphy, Shane M; Parrish, David D; Senff, Christoph J; Soltis, Jeffrey; Stutz, Jochen; Sweeney, Colm; Thompson, Chelsea R; Trainer, Michael K; Tsai, Catalina; Veres, Patrick R; Washenfelder, Rebecca A; Warneke, Carsten; Wild, Robert J; Young, Cora J; Yuan, Bin; Zamora, Robert

    2014-10-16

    The United States is now experiencing the most rapid expansion in oil and gas production in four decades, owing in large part to implementation of new extraction technologies such as horizontal drilling combined with hydraulic fracturing. The environmental impacts of this development, from its effect on water quality to the influence of increased methane leakage on climate, have been a matter of intense debate. Air quality impacts are associated with emissions of nitrogen oxides (NOx = NO + NO2) and volatile organic compounds (VOCs), whose photochemistry leads to production of ozone, a secondary pollutant with negative health effects. Recent observations in oil- and gas-producing basins in the western United States have identified ozone mixing ratios well in excess of present air quality standards, but only during winter. Understanding winter ozone production in these regions is scientifically challenging. It occurs during cold periods of snow cover when meteorological inversions concentrate air pollutants from oil and gas activities, but when solar irradiance and absolute humidity, which are both required to initiate conventional photochemistry essential for ozone production, are at a minimum. Here, using data from a remote location in the oil and gas basin of northeastern Utah and a box model, we provide a quantitative assessment of the photochemistry that leads to these extreme winter ozone pollution events, and identify key factors that control ozone production in this unique environment. We find that ozone production occurs at lower NOx and much larger VOC concentrations than does its summertime urban counterpart, leading to carbonyl (oxygenated VOCs with a C = O moiety) photolysis as a dominant oxidant source. Extreme VOC concentrations optimize the ozone production efficiency of NOx. There is considerable potential for global growth in oil and gas extraction from shale. This analysis could help inform strategies to monitor and mitigate air quality impacts

  10. Carbonyl sulfide exchange in soils for better estimates of ecosystem carbon uptake

    Directory of Open Access Journals (Sweden)

    M. E. Whelan

    2015-08-01

    Full Text Available Carbonyl sulfide (COS measurements are one of the emerging tools to better quantify gross primary production (GPP, the largest flux in the global carbon cycle. COS is a gas with a similar structure to CO2; COS uptake is thought to be a proxy for GPP. However, soils are a potential source or sink of COS. This study presents a framework for understanding soil-COS interactions. Excluding wetlands, most of the few observations of isolated soils that have been made show small uptake of atmospheric COS. Recently, a series of studies at an agricultural site in the central United States found soil COS production under hot conditions an order of magnitude greater than fluxes at other sites. To investigate the extent of this phenomenon, soils were collected from 5 new sites and incubated in a variety of soil moisture and temperature states. We found that soils from a desert, an oak savannah, a deciduous forest, and a rainforest exhibited small COS fluxes, behavior resembling previous studies. However, soil from an agricultural site in Illinois, > 800 km away from the initial central US study site, demonstrated comparably large soil fluxes under similar conditions. These new data suggest that, for the most part, soil COS interaction is negligible compared to plant uptake of COS. We present a model that anticipates the large agricultural soil fluxes so that they may be taken into account. While COS air-monitoring data are consistent with the dominance of plant uptake, improved interpretation of these data should incorporate the soil flux parameterizations suggested here.

  11. Soil-atmosphere carbonyl sulfide (COS) exchange in a tropical rainforest at La Selva, Costa Rica

    Science.gov (United States)

    Sun, W.; Maseyk, K. S.; Juarez, S.; Lett, C.; Seibt, U. H.

    2014-12-01

    Carbonyl sulfide (COS) has recently been proposed as a promising tracer for partitioning ecosystem carbon assimilation due to the close analogy between leaf uptake processes of COS and CO2. This emerging framework requires accurate characterization of the source and sink components of COS, including soil fluxes. Here we present the first direct, continuous observations of soil COS fluxes for 4 months at a tropical rainforest, La Selva Biological Station, Costa Rica. Three soil plots with contrasting water content were selected for chamber measurements. Our observations confirmed that soils are principally COS sinks, with daily mean COS fluxes averaged across all chambers ranging from -3 to 0 pmol m-2 s-1. When compared with net ecosystem COS uptake which peaks around -30 pmol m-2 s-1, their contributions should be considered in ecosystem COS balance. We did not find a temperature optimum, but soil COS uptake slightly increased with soil temperature, indicating biotic control on soil COS fluxes. Diurnal cycles of COS fluxes were observed during drying out periods after rain. The diel periodicity of COS fluxes was probably obscured by frequent raining at the site. Diffusional control of soil COS fluxes is shown from increasing soil COS uptake at lower soil water-filled pore space. These confirm that soil COS fluxes are mediated both by soil physical and biological factors. Using a depth-resolved diffusion-reaction model with data-driven enzyme activity parameterization, we simulated the COS fluxes from measured soil environmental variables, consistent with observations. This modeling scheme is useful for separating soil COS fluxes from net ecosystem COS fluxes, which lends support to the emergent COS-based approach of carbon flux partitioning.

  12. High winter ozone pollution from carbonyl photolysis in an oil and gas basin

    Science.gov (United States)

    Edwards, Peter M.; Brown, Steven S.; Roberts, James M.; Ahmadov, Ravan; Banta, Robert M.; Degouw, Joost A.; Dubé, William P.; Field, Robert A.; Flynn, James H.; Gilman, Jessica B.; Graus, Martin; Helmig, Detlev; Koss, Abigail; Langford, Andrew O.; Lefer, Barry L.; Lerner, Brian M.; Li, Rui; Li, Shao-Meng; McKeen, Stuart A.; Murphy, Shane M.; Parrish, David D.; Senff, Christoph J.; Soltis, Jeffrey; Stutz, Jochen; Sweeney, Colm; Thompson, Chelsea R.; Trainer, Michael K.; Tsai, Catalina; Veres, Patrick R.; Washenfelder, Rebecca A.; Warneke, Carsten; Wild, Robert J.; Young, Cora J.; Yuan, Bin; Zamora, Robert

    2014-10-01

    The United States is now experiencing the most rapid expansion in oil and gas production in four decades, owing in large part to implementation of new extraction technologies such as horizontal drilling combined with hydraulic fracturing. The environmental impacts of this development, from its effect on water quality to the influence of increased methane leakage on climate, have been a matter of intense debate. Air quality impacts are associated with emissions of nitrogen oxides (NOx = NO + NO2) and volatile organic compounds (VOCs), whose photochemistry leads to production of ozone, a secondary pollutant with negative health effects. Recent observations in oil- and gas-producing basins in the western United States have identified ozone mixing ratios well in excess of present air quality standards, but only during winter. Understanding winter ozone production in these regions is scientifically challenging. It occurs during cold periods of snow cover when meteorological inversions concentrate air pollutants from oil and gas activities, but when solar irradiance and absolute humidity, which are both required to initiate conventional photochemistry essential for ozone production, are at a minimum. Here, using data from a remote location in the oil and gas basin of northeastern Utah and a box model, we provide a quantitative assessment of the photochemistry that leads to these extreme winter ozone pollution events, and identify key factors that control ozone production in this unique environment. We find that ozone production occurs at lower NOx and much larger VOC concentrations than does its summertime urban counterpart, leading to carbonyl (oxygenated VOCs with a C = O moiety) photolysis as a dominant oxidant source. Extreme VOC concentrations optimize the ozone production efficiency of NOx. There is considerable potential for global growth in oil and gas extraction from shale. This analysis could help inform strategies to monitor and mitigate air quality impacts

  13. Carbonyl sulfide exchange in a temperate loblolly pine forest grown under ambient and elevated CO2

    Directory of Open Access Journals (Sweden)

    B. C. Sive

    2009-08-01

    Full Text Available Vegetation, soil and ecosystem level carbonyl sulfide (COS exchange was observed at Duke Forest, a temperate loblolly pine forest, grown under ambient (Ring 1, R1 and elevated (Ring 2, R2 carbon dioxide (CO2. During calm meteorological conditions, ambient COS mixing ratios at the top of the forest canopy followed a distinct diurnal pattern in both CO2 growth regimes, with maximum COS mixing ratios during the day (R1=380±4 pptv and R2=373±3 pptv, daytime mean ±standard error and minimums at night (R1=340±6 pptv and R2=346±5 pptv, nighttime mean ±standard error reflecting a significant nighttime sink. Nocturnal vegetative uptake (−11 to −21 pmol m−2 s−1, negative values indicate uptake from the atmosphere dominated nighttime net ecosystem COS flux estimates (−10 to −30 pmol m−2 s−1 in both CO2 regimes. In comparison, soil uptake (−0.8 to −1.7 pmol m−2 s−1 was a minor component of net ecosystem COS flux. In both CO2 regimes, loblolly pine trees exhibited substantial COS consumption overnight (50% of daytime rates that was independent of CO2 assimilation. This suggests current estimates of the global vegetative COS sink, which assume that COS and CO2 are consumed simultaneously, may need to be reevaluated. Ambient COS mixing ratios, species specific diurnal patterns of stomatal conductance, temperature and canopy position were the major factors influencing the vegetative COS flux at the branch level. While variability in branch level vegetative COS consumption measurements in ambient and enhanced CO2 environments could not be attributed to CO2 enrichment effects, estimates of net ecosystem COS flux based on ambient canopy mixing ratio measurements suggest less nighttime uptake of COS in R2, the CO2 enriched environment.

  14. Carbonyl sulfide exchange in a temperate loblolly pine forest grown under ambient and elevated CO2

    Directory of Open Access Journals (Sweden)

    B. C. Sive

    2010-01-01

    Full Text Available Vegetation, soil and ecosystem level carbonyl sulfide (COS exchange was observed at Duke Forest, a temperate loblolly pine forest, grown under ambient (Ring 1, R1 and elevated (Ring 2, R2 CO2. During calm meteorological conditions, ambient COS mixing ratios at the top of the forest canopy followed a distinct diurnal pattern in both CO2 growth regimes, with maximum COS mixing ratios during the day (R1=380±4 pptv and R2=373±3 pptv, daytime mean ± standard error and minimums at night (R1=340±6 pptv and R2=346±5 pptv, nighttime mean ± standard error reflecting a significant nighttime sink. Nocturnal vegetative uptake (−11 to −21 pmol m−2s−1, negative values indicate uptake from the atmosphere dominated nighttime net ecosystem COS flux estimates (−10 to −30 pmol m−2s−1 in both CO2 regimes. In comparison, soil uptake (−0.8 to −1.7 pmol m−2 s−1 was a minor component of net ecosystem COS flux. In both CO2 regimes, loblolly pine trees exhibited substantial COS consumption overnight (50% of daytime rates that was independent of CO2 assimilation. This suggests current estimates of the global vegetative COS sink, which assume that COS and CO2 are consumed simultaneously, may need to be reevaluated. Ambient COS mixing ratios, species specific diurnal patterns of stomatal conductance, temperature and canopy position were the major factors influencing the vegetative COS flux at the branch level. While variability in branch level vegetative COS consumption measurements in ambient and enhanced CO2 environments could not be attributed to CO2 enrichment effects, estimates of net ecosystem COS flux based on ambient canopy mixing ratio measurements suggest less nighttime uptake of COS in R2, the CO2 enriched environment.

  15. Do oceanic emissions account for the missing source of atmospheric carbonyl sulfide?

    Science.gov (United States)

    Lennartz, Sinikka; Marandino, Christa A.; von Hobe, Marc; Cortés, Pau; Simó, Rafel; Booge, Dennis; Quack, Birgit; Röttgers, Rüdiger; Ksionzek, Kerstin; Koch, Boris P.; Bracher, Astrid; Krüger, Kirstin

    2016-04-01

    Carbonyl sulfide (OCS) has a large potential to constrain terrestrial gross primary production (GPP), one of the largest carbon fluxes in the carbon cycle, as it is taken up by plants in a similar way as CO2. To estimate GPP in a global approach, the magnitude and seasonality of sources and sinks of atmospheric OCS have to be well understood, to distinguish between seasonal variation caused by vegetation uptake and other sources or sinks. However, the atmospheric budget is currently highly uncertain, and especially the oceanic source strength is debated. Recent studies suggest that a missing source of several hundreds of Gg sulfur per year is located in the tropical ocean by a top-down approach. Here, we present highly-resolved OCS measurements from two cruises to the tropical Pacific and Indian Ocean as a bottom-up approach. The results from these cruises show that opposite to the assumed ocean source, direct emissions of OCS from the tropical ocean are unlikely to account for the missing source. To reduce uncertainty in the global oceanic emission estimate, our understanding of the production and consumption processes of OCS and its precursors, dimethylsulfide (DMS) and carbon disulphide (CS2), needs improvement. Therefore, we investigate the influence of dissolved organic matter (DOM) on the photochemical production of OCS in seawater by considering analysis of the composition of DOM from the two cruises. Additionally, we discuss the potential of oceanic emissions of DMS and CS2 to closing the atmospheric OCS budget. Especially the production and consumption processes of CS2 in the surface ocean are not well known, thus we evaluate possible photochemical or biological sources by analyzing its covariation of biological and photochemical parameters.

  16. Observations of the uptake of carbonyl sulfide (COS by trees under elevated atmospheric carbon dioxide concentrations

    Directory of Open Access Journals (Sweden)

    L. Sandoval-Soto

    2012-08-01

    Full Text Available Global change forces ecosystems to adapt to elevated atmospheric concentrations of carbon dioxide (CO2. We understand that carbonyl sulfide (COS, a trace gas which is involved in building up the stratospheric sulfate aerosol layer, is taken up by vegetation with the same triad of the enzymes which are metabolizing CO2, i.e. ribulose-1,5-bisphosphate carboxylase/oxygenase (Rubisco, phosphoenolpyruvate carboxylase (PEP-Co and carbonic anhydrase (CA. Therefore, we discuss a physiological/biochemical acclimation of these enzymes affecting the sink strength of vegetation for COS. We investigated the acclimation of two European tree species, Fagus sylvatica and Quercus ilex, grown inside chambers under elevated CO2, and determined the exchange characteristics and the content of CA after a 1–2 yr period of acclimation from 350 ppm to 800 ppm CO2. We demonstrate that a compensation point, by definition, does not exist. Instead, we propose to discuss a point of uptake affinity (PUA. The results indicate that such a PUA, the CA activity and the deposition velocities may change and may cause a decrease of the COS uptake by plant ecosystems, at least as long as the enzyme acclimation to CO2 is not surpassed by an increase of atmospheric COS. As a consequence, the atmospheric COS level may rise causing an increase of the radiative forcing in the troposphere. However, this increase is counterbalanced by the stronger input of this trace gas into the stratosphere causing a stronger energy reflection by the stratospheric sulfur aerosol into space (Brühl et al., 2012. These data are very preliminary but may trigger a discussion on COS uptake acclimation to foster measurements with modern analytical instruments.

  17. Litter dominates surface fluxes of carbonyl sulfide in a Californian oak woodland

    Science.gov (United States)

    Sun, Wu; Maseyk, Kadmiel; Lett, Céline; Seibt, Ulli

    2016-02-01

    Carbonyl sulfide (COS) is a promising tracer for partitioning terrestrial photosynthesis and respiration from net carbon fluxes, based on its daytime co-uptake alongside CO2 through leaf stomata. Because ecosystem COS fluxes are the sum of plant and soil fluxes, using COS as a photosynthesis tracer requires accurate knowledge of soil COS fluxes. At an oak woodland in Southern California, we monitored below-canopy surface (soil + litter) COS and CO2 fluxes for 40 days using chambers and laser spectroscopy. We also measured litter fluxes separately and used a depth-resolved diffusion-reaction model to quantify the role of litter uptake in surface COS fluxes. Soil and litter were primarily COS sinks, and mean surface COS uptake was small (˜1 pmol m-2 s-1). After rainfall, uptake rates were higher (6-8 pmol m-2 s-1), and litter contributed a significant fraction (up to 90%) to surface fluxes. We observed rapid concurrent increases in COS uptake and CO2 efflux following the onset of rain. The patterns were similar to the Birch effect widely documented for soils; however, both COS and CO2 flux increases originated mainly in the litter. The synchronous COS-CO2 litter Birch effect indicates that it results from a rapid increase in litter microbial activity after rainfall. We expect that the drying-rewetting cycles typical for mediterranean and other semiarid ecosystems create a pronounced seasonality in surface COS fluxes. Our results highlight that litter uptake is an important component of surface COS exchange that needs to be taken into account in ecosystem COS budgets and model simulations.

  18. Microwave absorbing property of silicone rubber composites with added carbonyl iron particles and graphite platelet

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Yonggang; Zhang, Deyuan [Bionic and Micro/Nano/Bio-Manufacturing Technology Research Center, School of Mechanical Engineering and Automation, Beihang University, Beijing 100191 (China); Cai, Jun, E-mail: jun_cai@buaa.edu.cn [Bionic and Micro/Nano/Bio-Manufacturing Technology Research Center, School of Mechanical Engineering and Automation, Beihang University, Beijing 100191 (China); Yuan, Liming; Zhang, Wenqiang [Bionic and Micro/Nano/Bio-Manufacturing Technology Research Center, School of Mechanical Engineering and Automation, Beihang University, Beijing 100191 (China)

    2013-02-15

    Silicone rubber composites filled with carbonyl iron particles (CIPs) and graphite platelet (GP) were prepared using non-coating or coating processes. The complex permittivity and permeability of the composites were measured using a vector network analyzer in the frequency range of 1-18 GHz and dc electric conductivity was measured by the standard four-point contact method. The results showed that CIPs/GP composites fabricated in the coating process had the highest permittivity and permeability due to the particle orientation and interactions between the two absorbents. The coating process resulted in a decreased effective eccentricity of the absorbents, and the dc conductivity increased according to Neelakanta's equations. The reflection loss (RL) value showed that the composites had an excellent absorbing property in the L-band, minimum -11.85 dB at 1.5 mm and -15.02 dB at 2 mm. Thus, GP could be an effective additive in preparing thin absorbing composites in the L-band. - Highlights: Black-Right-Pointing-Pointer The added GP increased the permittivity and permeability of composites filled with CIPs. Black-Right-Pointing-Pointer The enhancement was owing to interactions of the two absorbents and the fabrication process. Black-Right-Pointing-Pointer The coating process decreased the effective eccentricity of the particles, and increased the conductivity of the composites. Black-Right-Pointing-Pointer The composites to which CIPs/GP were added in coating process had excellent absorbing properties in the L-band.

  19. Measurements of C{sub 1}-C{sub 4} carbonyls at forested regions in Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Ceron Breton, J.B.; Padilla, H.; Belmont, R.; Torres, M.C.; Moya, M.; Baez, A.P. [Centro de Ciencias de la Atmosfera, Universidad Nacional Autonoma de Mexico, UNAM, Mexico, D.F. (Mexico)

    2005-04-01

    Measurements of formaldehyde, acetaldehyde, acetone, propionaldehyde and butyraldehyde concentrations were made at five different forested regions in Mexico. One set of two simultaneous samplings was performed at two sites located in the Mexico State, one semi rural area (Temascaltepec), and the other, a forested area (Rancho Viejo). A second set of two simultaneous samplings were made in southern Veracruz State, in one rural area (Monte Pio) and inside a tropical rainforest (at the Biology Station of the University of Mexico). Finally, one sampling was performed in the Sierra of Puebla State (Cuetzalan). Propionaldehyde and butyraldehyde were nor reported because their concentrations were always below or near the detection limit of the technique. The highest concentrations were found from 7:00 to 11:00 and from 11:00 to 19:00 h in all the sampling sites. Arithmetic mean concentrations of acetone were the highest observed among the detected carbonyl compounds in almost all sites, ranging from 0.5 to 8.4 {mu}g m{sup -}3. Arithmetic mean concentrations of formaldehyde and acetaldehyde ranged from 0.83 to 6 {mu}g m{sup -}3 and 0.53 to 4.7 {mu}g m{sup -}3, respectively. The Spearman's correlations between formaldehyde and acetone, and between acetaldehyde and acetone were statistically significant at p<0.05 in almost all sites. A significant correlation (p<0.05) between formaldehyde and acetaldehyde was observed in Mexico State at Rancho Viejo and Temascaltepec. The mean ratio HCHO/CH{sub 3}CHO of concentrations was 1.83 and 1.31 in the forested area of Rancho Viejo, first and second sampling periods, respectively; 1.71 and 1.62 in the semi rural area of Temascaltepec, first and second sampling periods respectively; 1.70 in Cuetzalan; 2.90 in the rural area of Monte Pio; and 1.61 in the Biology Station tropical rainforest. These values show a greater influence of atmospheric pollutants transported from sites with anthropogenic activities, because HCHO/CH{sub 3}CHO

  20. Characterization of the lanthanum chloride scintillation detector

    International Nuclear Information System (INIS)

    This paper reports about the investigations on the performance of the new earth-rare halide Scintillator, the LaCl3:10%Ce, which has been discovered with attractive scintillation properties: fast, efficient, and high-energy resolution. The combination of good brightness and linear response has naturally resulted in a very good energy resolution, whereas the fast decay time promoted counting applications at very high rate and very fast timing resolution. Energy resolutions of (2.99±0.02) %, (8.66±0.02) %, and (2.05±0.01) % have been achieved by exciting the detector with 662 keV 137Cs, 122 keV 152Eu, and 1332.5 keV 60Co sources respectively, at room temperature. The variations of the resolution as a function of both shaping time and high voltage have been studied and found to be relatively linear. The timing resolution was also studied. The value of 1.07 ns FWHM has been recorded with LaCl3:10%Ce and BaF2 detectors operating in coincidence mode, using 1333.5 keV γ-ray 60Co peak. Compared to similar studies, this timing resolution was worse than expected even if the exciting radioactive sources used in the two experiments were different. The efficiency values of (0.24±0.01)%, (0.01±0.01)% and (0.09±0.01)% were obtained with laboratory 137Cs, 152Eu, 60Co isotopes respectively. These detector efficiency values were very low, due to the smaller detector sizes used in these earlier crystals and to the large detector-source-distance used in this experiment. The Lanthanum Chloride Scintillator detector is hygroscopic and relatively expensive compared to established scintillators. In addition, it carries internal contamination in 138La and 227Ac for larger thicknesses. Nevertheless, the energy resolution figures achieved, twice as good as that of NaI(Tl), are in good agreement with those reported elsewhere. They credit the scintillation detectors as good challengers of semiconductor-based detectors, allowing their application fields to be extended. (author)