WorldWideScience

Sample records for carbon fluorides

  1. Fluoride and lead adsorption on carbon nanotubes

    Institute of Scientific and Technical Information of China (English)

    WANG Shuguang; LI Yanhui

    2004-01-01

    The properties and applications of CNT have been studied extensively since Iijima discovered them in 1991[1,2]. They have exceptional mechanical properties and unique electrical property, highly chemical stability and large specific surface area. Thus far, they have widely potential applications in many fields. They can be used as reinforcing materials in composites[3], field emissions[4], hydrogen storage[5], nanoelectronic components[6], catalyst supports[7], adsorption material and so on. However, the study on the potential application of CNT, environmental protection field in particular, was hardly begun.Long[8] et al. reported that CNT had a significantly higher dioxin removal efficiency than that of activated carbon. The Langmuir adsorption constant is 2.7 × 1052, 1.3 × 1018 respectively. The results indicated that CNT is potential candidate for the removal of micro-organic pollutants. However, the reports on the CNT used as fluoride and heavy metal adsorbent are seldom.In this paper, A novel material, alumina supported on carbon nanotubes (Al2O3/CNT), was prepared from carbon nanotubes and Al(NO3)3. X-ray diffraction (XRD) spectra demonstrate that alumina is amorphous, and scanning electron microscope (SEM) images show that CNT and alumina are homogeneously mixed. Furthermore, the fluoride adsorption behavior on the surface of Al2O3/CNT has been investigated and compared with other adsorbents. The results indicate that Al2O3/CNT has a high adsorption capacity, with a saturation adsorption capacity of 39.4 mg/g. It is also found that the adsorption capacity of Al2O3/CNT is 3.0~4.5 times that of γ-Al2O3while almost equal to that of IRA-410 polymeric resin at 25 ℃. The adsorption isotherms of fluoride on Al2O3/CNT is fit the Freundlich equation well, optimal pH ranging from 5.0 to 9.0.Also in this paper, a novel material, modified carbon nanotubes (CNT), was prepared from carbon nanotubes and HNO3 under boiling condition. Infrared spectroscopy (IR

  2. Ion chromatography detection of fluoride in calcium carbonate.

    Science.gov (United States)

    Lefler, Jamie E; Ivey, Michelle M

    2011-09-01

    Fluoride in aquatic systems is increasing due to anthropogenic pollution, but little is known about how this fluoride affects organisms that live in and around aquatic habitats. Fluoride can bioaccumulate in structures comprised of calcium carbonate, such as shells and skeletons of both freshwater and saltwater species as diverse as snails, corals, and coccolithophorid algae. In this article, ion chromatography (IC) techniques are developed to detect and quantify fluoride in a matrix of calcium carbonate. Solid samples are dissolved in hydrochloric acid, pretreated to remove the majority of the chloride ions, and then analyzed using IC. With these methods, the 3σ limit of detection is 0.2 mg of fluoride/kg of calcium carbonate. PMID:21859530

  3. Fluoride

    Science.gov (United States)

    Fluoride is used to prevent tooth decay. It is taken up by teeth and helps to strengthen ... and block the cavity-forming action of bacteria. Fluoride usually is prescribed for children and adults whose ...

  4. Fluoride content in bottled drinking waters, carbonated soft drinks and fruit juices in Davangere city, India

    OpenAIRE

    Thippeswamy H; Kumar Nanditha; Anand S; Prashant G; Chandu G

    2010-01-01

    Background: The regular ingestion of fluoride lowers the prevalence of dental caries. The total daily intake of fluoride for optimal dental health should be 0.05-0.07 mg fluoride/kg body weight and to avoid the risk of dental fluorosis, the daily intake should not exceed a daily level of 0.10 mg fluoride/kg body weight. The main source of fluoride is from drinking water and other beverages. As in other countries, consumption of bottled water, juices and carbonated beverages has increased in o...

  5. The Effect of Carbon Source and Fluoride Concentrations in the "Streptococcus Mutans" Biofilm Formation

    Science.gov (United States)

    Paulino, Tony P.; Andrade, Ricardo O.; Bruschi-Thedei, Giuliana C. M.; Thedei, Geraldo, Jr.; Ciancaglini, Pietro

    2004-01-01

    The main objective of this class experiment is to show the influence of carbon source and of different fluoride concentrations on the biofilm formation by the bacterium "Streptococcus mutans." The observation of different biofilm morphology as a function of carbon source and fluoride concentration allows an interesting discussion regarding the…

  6. Fluoride content in bottled drinking waters, carbonated soft drinks and fruit juices in Davangere city, India

    Directory of Open Access Journals (Sweden)

    Thippeswamy H

    2010-01-01

    Full Text Available Background: The regular ingestion of fluoride lowers the prevalence of dental caries. The total daily intake of fluoride for optimal dental health should be 0.05-0.07 mg fluoride/kg body weight and to avoid the risk of dental fluorosis, the daily intake should not exceed a daily level of 0.10 mg fluoride/kg body weight. The main source of fluoride is from drinking water and other beverages. As in other countries, consumption of bottled water, juices and carbonated beverages has increased in our country. Objective: To analyze the fluoride content in bottled water, juices and carbonated soft drinks that were commonly available in Davangere city. Materials and Methods: Three samples of 10 commercially available brands of bottled drinking water, 12 fruit juices and 12 carbonated soft drinks were purchased. Bottled water and carbonated soft drinks were stored at a cold place until fluoride analysis was performed and a clear juice was prepared using different fruits without the addition of water. Then, the fluoride analysis was performed. Results: The mean and standard deviation of fluoride content of bottled water, fruit juices and carbonated soft drinks were measured, which were found to be 0.20 mg (±0.19 F/L, 0.29 mg (±0.06 F/L and 0.22 mg (±0.05 F/L, respectively. Conclusion: In viewing the results of the present study, it can be concluded that regulation of the optimal range of fluoride in bottled drinking water, carbonated soft drinks and fruit juices should be drawn for the Indian scenario.

  7. Fluoride enhances transfection activity of carbonate apatite by increasing cytoplasmic stability of plasmid DNA

    International Nuclear Information System (INIS)

    Highlights: → Cytoplasmic stability of plasmid DNA is enhanced by fluoride incorporation into carbonate apatite carrier. → Fluoridated carbonate apatite promotes a robust increase in transgene expression. → Controlled dissolution of fluoridated carbonate apatite in endosomal acidic environment might buffer the endosomes and prevent degradation of the released DNA. -- Abstract: Intracellular delivery of a functional gene or a nucleic acid sequence to specifically knockdown a harmful gene is a potential approach to precisely treat a critical human disease. The intensive efforts in the last few decades led to the development of a number of viral and non-viral synthetic vectors. However, an ideal delivery tool in terms of the safety and efficacy has yet to be established. Recently, we have developed pH-sensing inorganic nanocrystals of carbonate apatite for efficient and cell-targeted delivery of gene and gene-silencing RNA. Here we show that addition of very low level of fluoride to the particle-forming medium facilitates a robust increase in transgene expression following post-incubation of the particles with HeLa cells. Confocal microscopic observation and Southern blotting prove the cytoplasmic existence of plasmid DNA delivered by likely formed fluoridated carbonate apatite particles while degradation of plasmid DNA presumably by cytoplasmic nucleases was noticed following delivery with apatite particles alone. The beneficial role of fluoride in enhancing carbonate apatite-mediated gene expression might be due to the buffering potential of generated fluoridated apatite in endosomal acidic environment, thereby increasing the half-life of delivered plasmid DNA.

  8. Tamarind (Tamarindus indica) fruit shell carbon: A calcium-rich promising adsorbent for fluoride removal from groundwater.

    Science.gov (United States)

    Sivasankar, V; Rajkumar, S; Murugesh, S; Darchen, A

    2012-07-30

    Tamarindus indica fruit shells (TIFSs) are naturally calcium rich compounds. They were impregnated with ammonium carbonate and then carbonized, leading to ammonium carbonate activated ACA-TIFS carbon. The resulting materials and carbon arising from virgin fruit shells V-TIFS were characterized and assayed as adsorbent for the removal of fluoride anions from groundwater. The fluoride scavenging ability of TIFS carbons was due to naturally dispersed calcium compounds. X-ray diffraction (XRD) showed that TIFS carbon contained a mixture of calcium oxalate and calcium carbonate. Batch studies on the fluoride removal efficiency of TIFS carbons with respect to contact time, pH, initial fluoride concentration, and co-ion interference were conducted. Applicability of various kinetic models (viz., pseudo-first-order, pseudo-second-order, intra-particle diffusion and Elovich) and sorption isotherms were tested for batch techniques. The fluoride removal capacity of TIFS carbons was found to be 91% and 83% at a pH of 7.05 for V-TIFS and ACA-TIFS carbons, respectively. The practical applicability of TIFS carbons using groundwater samples was approved. The fluoride removal was greater in groundwater without hydrogen carbonate ions than those containing these ions. The characterizations of fluoride unloaded and loaded TIFS carbons were done by SEM and XRD studies.

  9. Tamarind (Tamarindus indica) fruit shell carbon: A calcium-rich promising adsorbent for fluoride removal from groundwater

    Energy Technology Data Exchange (ETDEWEB)

    Sivasankar, V., E-mail: vsivasankar@tce.edu [Department of Chemistry, Thiagarajar College of Engineering (Autonomous), Madurai 625015, Tamil Nadu (India); Rajkumar, S. [Department of Chemistry, Thiagarajar College of Engineering (Autonomous), Madurai 625015, Tamil Nadu (India); Murugesh, S. [Department of Chemistry, SACS M.A.V.M.M. Engineering College, Madurai 625301, Tamil Nadu (India); Darchen, A. [UMR CNRS No. 6226 Sciences Chimiques de Rennes, ENSCR, Avenue du General Leclerc, CS 50837, 35708 Rennes, Cedex 7 (France)

    2012-07-30

    Highlights: Black-Right-Pointing-Pointer The carbonization of Tamarind fruit shell improved its defluoridation efficiency. Black-Right-Pointing-Pointer Calcium carbonate particles were involved in the defluoridation process. Black-Right-Pointing-Pointer Adsorbent dose, pH, and fluoride concentration showed significant effects. Black-Right-Pointing-Pointer Maximum adsorption of fluoride was achieved at pH 7-8. Black-Right-Pointing-Pointer Prepared carbons were efficient in treating three natural waters. - Abstract: Tamarindus indica fruit shells (TIFSs) are naturally calcium rich compounds. They were impregnated with ammonium carbonate and then carbonized, leading to ammonium carbonate activated ACA-TIFS carbon. The resulting materials and carbon arising from virgin fruit shells V-TIFS were characterized and assayed as adsorbent for the removal of fluoride anions from groundwater. The fluoride scavenging ability of TIFS carbons was due to naturally dispersed calcium compounds. X-ray diffraction (XRD) showed that TIFS carbon contained a mixture of calcium oxalate and calcium carbonate. Batch studies on the fluoride removal efficiency of TIFS carbons with respect to contact time, pH, initial fluoride concentration, and co-ion interference were conducted. Applicability of various kinetic models (viz., pseudo-first-order, pseudo-second-order, intra-particle diffusion and Elovich) and sorption isotherms were tested for batch techniques. The fluoride removal capacity of TIFS carbons was found to be 91% and 83% at a pH of 7.05 for V-TIFS and ACA-TIFS carbons, respectively. The practical applicability of TIFS carbons using groundwater samples was approved. The fluoride removal was greater in groundwater without hydrogen carbonate ions than those containing these ions. The characterizations of fluoride unloaded and loaded TIFS carbons were done by SEM and XRD studies.

  10. Carbide Coatings for Nickel Alloys, Graphite and Carbon/Carbon Composites to be used in Fluoride Salt Valves

    Energy Technology Data Exchange (ETDEWEB)

    Nagle, Denis [Johns Hopkins Univ., Baltimore, MD (United States); Zhang, Dajie [Johns Hopkins Univ., Baltimore, MD (United States)

    2015-10-22

    The focus of this research was concerned with developing materials technology that supports the evolution of Generation IV Advanced High Temperature Reactor (AHTR) concepts. Specifically, we investigate refractory carbide coatings for 1) nickel alloys, and 2) commercial carbon-carbon composites (CCCs). Numerous compelling reasons have driven us to focus on carbon and carbide materials. First, unlike metals, the strength and modulus of CCCs increase with rising temperature. Secondly, graphite and carbon composites have been proven effective for resisting highly corrosive fluoride melts such as molten cryolite [Na₃AlF₆] at ~1000°C in aluminum reduction cells. Thirdly, graphite and carbide materials exhibit extraordinary radiation damage tolerance and stability up to 2000°C. Finally, carbides are thermodynamically more stable in liquid fluoride salt than the corresponding metals (i.e. Cr and Zr) found in nickel based alloys.

  11. Electrothermal Performances of Poly(Vinylidiene Fluoride)/Fluorine Rubber Conductive Composite Filled with Carbon Black

    Institute of Scientific and Technical Information of China (English)

    LUO; YanLing

    2001-01-01

    The conductive polymer composites and their corresponding resistors with PTC (positive temperature coefficient) characteristic can be manufactured by mixing conductive carbon blacks with poly(vinylidiene fluoride )matrix. The Joule heat can produce when alternative voltage is exerted on the composite resistors, and the resistors can produce when alternative voltage is exerted on the current from flowing at a high temperature because of their PTC effect, thus becoming a kind of important thermoelectric switching materials as heating, temperature-controlling and currentlinfiting element applications.  ……

  12. Electrothermal Performances of Poly(Vinylidiene Fluoride)/Fluorine Rubber Conductive Composite Filled with Carbon Black

    Institute of Scientific and Technical Information of China (English)

    LUO YanLing

    2001-01-01

    @@ The conductive polymer composites and their corresponding resistors with PTC (positive temperature coefficient) characteristic can be manufactured by mixing conductive carbon blacks with poly(vinylidiene fluoride )matrix. The Joule heat can produce when alternative voltage is exerted on the composite resistors, and the resistors can produce when alternative voltage is exerted on the current from flowing at a high temperature because of their PTC effect, thus becoming a kind of important thermoelectric switching materials as heating, temperature-controlling and currentlinfiting element applications.

  13. Controlled fluoridation of amorphous carbon films deposited at reactive plasma conditions

    Directory of Open Access Journals (Sweden)

    Yoffe Alexander

    2015-09-01

    Full Text Available A study of the correlations between plasma parameters, gas ratios, and deposited amorphous carbon film properties is presented. The injection of a C4F8/Ar/N2 mixture of gases was successfully used in an inductively coupled plasma system for the preparation of amorphous carbon films with different fluoride doping at room-temperature, using silicon as a substrate. This coating was formed at low-pressure and low-energy using an inductively coupled plasma process. A strong dependence between the ratios of gases during deposition and the composition of the substrate compounds was shown. The values of ratios between Ar (or Ar+N2 and C4F8 - 1:1 and between N2 and Ar - 1:2 in the N2/Ar/C4F8 mixture were found as the best for low fluoridated coatings. In addition, an example of improving the etch-passivation in the Bosch procedure was described. Scanning electron microscopy with energy dispersive spectroscopy options, X-ray diffraction, and X-ray reflectivity were used for quantitative analysis of the deposited films.

  14. Use of chemically activated cotton nut shell carbon for the removal of fluoride contaminated drinking water:Kinetics evaluation☆

    Institute of Scientific and Technical Information of China (English)

    Rajan Mariappan; Raj Vairamuthu; Alagumuthu GanapathY

    2015-01-01

    Chemically activated cotton nut shell carbons (CTNSCs) were prepared by different chemicals and they were used for the removal of fluoride from aqueous solution. Effects of adsorption time, adsorbent dose, pH of the solution, initial concentration of fluoride, and temperature of the solution were studied with equilibrium, ther-modynamics and kinetics of the adsorption process by various CTNSC adsorbents. It showed that the chemical y activated CTNSCs can effectively remove fluoride from the solution. The adsorption equilibrium data correlate well with the Freundlich isotherm model. The adsorption of fluoride by the chemical y activated CTNSC is spon-taneous and endothermic in nature. The pseudo first order, pseudo second order and intra particle diffusion kinetic models were applied to test the experimental data. The pseudo second order kinetic model provided a better correlation of the experimental data in comparison with the pseudo-first-order and intra particle diffusion models. A mechanism of fluoride adsorption associating chemisorption and physisorption processes is presented allowing the discussion of the variations in adsorption behavior between these materials in terms of specific surface area and porosity. These data suggest that chemically activated CTNSCs are promising materials for fluoride sorption.

  15. Do-Fluoride "Cryolite By- product Carbon White" Awarded the 13th China Excellent Patent Award%Do-Fluoride "Cryolite By- product Carbon White" Awarded the 13th China Excellent Patent Award

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    On November 4, the results of the 13th China Patent Awards were publicized by the State Intellectual Property Office of the People's Republic of China. The patent of "production method of cryolite by-product carbon white" declared by Henan Province Jiaozuo Do-Fluoride Company was awarded China Excellent Patent Award.

  16. Sub percolation threshold carbon nanotube based polyvinylidene fluoride polymer-polymer composites

    Science.gov (United States)

    Jacob, Cedric Antony

    The study of piezoelectric materials has traditionally focused largely on homogeneous crystalline or semi-crystalline materials. This research focuses on the concept of piezoelectric composites using selective microstructural reinforcement in the piezoelectric material to improve the piezoelectric properties. This is done using a polyvinylidene fluoride (PVDF) and carbon nanotube composite as the model system. A multi-tiered engineering approach is taken to understand the material (experimental and computational analyses) and design a composite system which provides an effective platform for future research in piezoelectric improvement. A finite element analysis is used to evaluate the ability of carbon nanotubes to generate a heterogeneous electric field where local improvements in electric field produce an increase in the effective piezoelectric strength. The study finds that weight percent and aspect ratio of the carbon nanotubes are of key importance while formations of percolating networks are detrimental to performance. This motivates investigation into electrospinning into a method of producing sub percolation threshold composites with large carbon nanotube content. However, the electrospun fabrics have too low of a dielectric strength to sustain high strength electric fields. This is studied within the context of high voltage physics and a solution inspired by traditional composites manufacturing is proposed wherein the electrospun fiber mat is used as the fiber reinforcing component of a polymer-polymer composite. This composite is thoroughly analyzed to show that it allows for a high dielectric strength combined with high carbon nanotube content. It is also shown that the PVDF contains the proper crystal structure to allow for piezoelectric properties. Furthermore, the addition of carbon nanotubes greatly improves the strength and stiffness of the composite, as well as affecting the internal electric field response to an applied voltage. These qualities

  17. Removal of fluoride by thermally activated carbon prepared from neem (Azadirachta indica) and kikar (Acacia arabica) leaves.

    Science.gov (United States)

    Kumar, Sunil; Gupta, Asha; Yadav, J P

    2008-03-01

    The present investigation deals with fluoride removal from aqueous solution by thermally activated neem (Azadirachta indica) leaves carbon (ANC) and thermally activated kikar (Acacia arabica) leaves carbon (AKC) adsorbents. In this study neem leaves carbon and kikar leaves carbon prepared by heating the leaves at 400 degrees C in electric furnace was found to be useful for the removal of fluoride. The adsorbents of 0.3 mm and 1.0 mm sizes of neem and kikar leaves carbon was prepared by standard sieve. Batch experiments done to see the fluoride removal properties from synthetic solution of 5 ppm to study the influence of pH, adsorbent dose and contact time on adsorption efficiency The optimum pH was found to be 6 for both adsorbents. The optimum dose was found to be 0.5g/100 ml forANC (activated neem leaves carbon) and 0.7g/100 ml forAKC (activated kikar leaves carbon). The optimum time was found to be one hour for both the adsorbent. It was also found that adsorbent size of 0.3 mm was more efficient than the 1.0 mm size. The adsorption process obeyed Freundlich adsorption isotherm. The straight line of log (qe-q) vs time at ambient temperature indicated the validity of langergren equation consequently first order nature of the process involved in the present study. Results indicate that besides intraparticle diffusion there maybe other processes controlling the rate which may be operating simultaneously. All optimized conditions were applied for removal of fluoride from four natural water samples.

  18. Formation and chemical reactivity of carbon fibers prepared by defluorination of graphite fluoride

    Science.gov (United States)

    Hung, Ching-Cheh

    1994-01-01

    Defluorination of graphite fluoride (CFX) by heating to temperatures of 250 to 450 C in chemically reactive environments was studied. This is a new and possibly inexpensive process to produce new carbon-based materials. For example, CF 0.68 fibers, made from P-100 carbon fibers, can be defluorinated in BrH2C-CH = CH-CH2Br (1,4-dibromo-2butene) heated to 370 C, and graphitized to produce fibers with an unusually high modulus and a graphite layer structure that is healed and cross-linked. Conversely, a sulfur-doped, visibly soft carbon fiber was produced by defluorinating CF 0.9 fibers, made from P-25, in sulfur (S) vapor at 370 C and then heating to 660 C in nitrogen (N2). Furthermore, defluorination of the CF 0.68 fibers in bromine (Br2) produced fragile, structurally damaged carbon fibers. Heating these fragile fibers to 1100 C in N2 caused further structural damage, whereas heating to 150 C in bromoform (CHBr3) and then to 1100 C in N2 healed the structural defects. The defluorination product of CFX, tentatively called activated graphite, has the composition and molecular structure of graphite, but is chemically more reactive. Activated graphite is a scavenger of manganese (Mn), and can be intercalated with magnesium (Mg). Also, it can easily collect large amounts of an alloy made from copper (Cu) and type 304 stainless steel to form a composite. Finally, there are indications that activated graphite can wet metals or ceramics, thereby forming stronger composites with them than the pristine carbon fibers can form.

  19. Fluoridated Water

    Science.gov (United States)

    ... Cancer Prevention Overview–for health professionals Research Fluoridated Water On This Page What is fluoride, and where is it found? What is water fluoridation? When did water fluoridation begin in the ...

  20. Process optimization for methyl ester production from waste cooking oil using activated carbon supported potassium fluoride

    Energy Technology Data Exchange (ETDEWEB)

    Hameed, B.H.; Goh, C.S.; Chin, L.H. [School of Chemical Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia)

    2009-12-15

    This paper presents the transesterification of waste cooking palm oil (WCO) using activated carbon supported potassium fluoride catalyst. A central composite rotatable design was used to optimize the effect of molar ratio of methanol to oil, reaction period, catalyst loading and reaction temperature on the transesterification process. The reactor was pressurized up to 10 bar using nitrogen gas. All the variables were found to affect significantly the methyl ester yield where the most effective factors being the amount of catalyst and reaction temperature, followed by methanol to oil ratio. A quadratic polynomial equation was obtained for methyl ester yield by multiple regression analysis using response surface methodology (RSM). The optimum condition for transesterification of WCO to methyl ester was obtained at 3 wt.% amount of catalyst, 175 C temperature, 8.85 methanol to oil molar ratio and 1 h reaction time. At the optimum condition, the predicted methyl ester yield was 83.00 wt.%. The experimental value was well within the estimated value of the model. The catalyst showed good performance with a high yield of methyl ester and the separation of the catalyst from the liquid mixture is easy. (author)

  1. Effect of titanium tetrafluoride and amine fluoride treatment combined with carbon dioxide laser irradiation on enamel and dentin erosion

    OpenAIRE

    Wiegand, A.; Magalhães, A C; Navarro, R S; Schmidlin, P R; Rios, D.; Buzalaf, M.A.R.; Attin, T.

    2010-01-01

    OBJECTIVE: This in vitro study aimed to analyze the influence of carbon dioxide (CO(2)) laser irradiation on the efficacy of titanium tetrafluoride (TiF(4)) and amine fluoride (AmF) in protecting enamel and dentin against erosion. METHODS: Bovine enamel and dentin samples were pretreated with carbon dioxide (CO(2)) laser irradiation only (group I), TiF(4) only (1% F, group II), CO(2) laser irradiation before (group III) or through (group IV) TiF(4) application, AmF only (1% F, group V), or CO...

  2. Polypyrrole-grafted peanut shell biological carbon as a potential sorbent for fluoride removal: Sorption capability and mechanism.

    Science.gov (United States)

    Li, Chunlu; Chen, Nan; Zhao, Yanan; Li, Rui; Feng, Chuanping

    2016-11-01

    In this study, an effective defluoridation adsorbent was developed by depositing polypyrrole (PPy) on granular peanut shell biological carbon (BC) via in situ chemical oxidative polymerization. The variables of defluoridation process (i.e., adsorbent dosage, fluoride solution pH, and anionic interference) were tested. The mechanism was determined by isotherm and kinetic studies, Brunauer-Emmett-Teller (BET) method, scanning electronic microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR) spectroscopy and automatic titration. The PPy-grafted BC (PPy/BC) composite performed commendably from pH 2.0 to 10.0, and exhibited high selectivity for fluoride in the presence of several co-existing anions. The experimental data were described well by a Langmuir isotherm curve, and the maximum adsorption capacity was 17.15 mg g(-1). Kinetic studies illustrated the adsorption process was accomplished via surface adsorption as well as by intraparticle diffusion. In addition, mesoporous diffusion was the rate-controlling step in intraparticle diffusion process. BET and SEM analysis revealed the sponge-like polymer adhered to the BC and plugged the pores. XPS, FTIR, and SEM confirmed that fluoride removal was accomplished via the replacement of doped ionizable chloride ions (Cl(-)) coupled with positively charged nitrogen (N(+)), computation of XPS data enabled the formulation of a three-layer-deep hypothesis for PPy. PMID:27521642

  3. Flexible carbon nanofiber/polyvinylidene fluoride composite membranes as interlayers in high-performance Lithiumsbnd Sulfur batteries

    Science.gov (United States)

    Wang, Zhenhua; Zhang, Jing; Yang, Yuxiang; Yue, Xinyang; Hao, Xiaoming; Sun, Wang; Rooney, David; Sun, Kening

    2016-10-01

    Traditionally polyvinylidene fluoride membranes have been used in applications such as membrane distillation, wastewater treatment, desalination and separator fabrication. Within this work we demonstrate that a novel carbon nanofiber/polyvinylidene fluoride (CNF/PVDF) composite membrane can be used as an interlayer for Lithiumsbnd Sulfur (Lisbnd S) batteries yielding both high capacity and long cycling life. This PVDF membrane is shown to effectively separate dissolved lithium polysulfide with the high electronic conductivity CNF not only reducing the internal resistance in the sulfur cathode but also helping immobilize the polysulfide through its abundant nanospaces. The resulting Lisbnd S battery assembled with the CNF/PVDF composite membrane effectively solves the polysulfide permeation problem and exhibits excellent electrochemical performance. It is further shown that the CNF/PVDF electrode has an excellent cycling stability and retains a capacity of 768.6 mAh g-1 with a coulombic efficiency above 99% over 200 cycles at 0.5C, which is more than twice that of a cell without CNF/PVDF (374 mAh g-1). In addition, the low-cost raw materials and the simple preparation process of CNF/PVDF composite membrane is also amenable for industrial production.

  4. Composites of hybrids BaTiO3/carbon nanotubes/polyvinylidene fluoride with high dielectric properties

    Science.gov (United States)

    Fan, Benhui; Bai, Jinbo

    2015-11-01

    High dielectric composites were prepared based on polyvinylidene fluoride (PVDF) and hybrids BaTiO3-carbon nanotubes (H-BT-CNTs) with a special structure. The hybrids that BT was a core and CNTs grew outside were fabricated by chemical vapor deposition. Due to the special structure, composite’s dielectric permittivity reached 1777 at 100 Hz and 80 at 1 MHz, while loss tangent maintained as 6 at 100 Hz and 0.56 at 1 MHz, respectively. Moreover, dielectric permittivity and ac conductivity of composite were further enhanced after annealing process at moderate temperature. These improved properties were originated from the reformation of conductive network and BT-CNTs structure inside PVDF matrix.

  5. Crystallization and mechanical properties of functionalized single-walled carbon nanotubes/polyvinylidene fluoride composites

    DEFF Research Database (Denmark)

    Ma, Jing; Iftekharul Haque, Rubaiyet; Larsen, Mikael

    2012-01-01

    Single-walled carbon nanotubes were purified and functionalized by nitric acid and octadecylamine. Raman and Fourier transform infrared spectroscopy were used to characterize the functionalization of the single-walled carbon nanotubes. Polyvinylidene flouride nanocomposites containing 1 wt......% purified or functionalized single-walled carbon nanotubes were prepared by solution blending and injection molding. The dispersion of different carbon nanotubes in dimethylformamide and in polyvinylidene flouride has been investigated. Mechanical properties show that adding single-walled carbon nanotubes...

  6. Effect of the carbon nanotube surface characteristics on the conductivity and dielectric constant of carbon nanotube/poly(vinylidene fluoride composites

    Directory of Open Access Journals (Sweden)

    Pereira João

    2011-01-01

    Full Text Available Abstract Commercial multi-walled carbon nanotubes (CNT were functionalized by oxidation with HNO3, to introduce oxygen-containing surface groups, and by thermal treatments at different temperatures for their selective removal. The obtained samples were characterized by adsorption of N2 at -196°C, temperature-programmed desorption and determination of pH at the point of zero charge. CNT/poly(vinylidene fluoride composites were prepared using the above CNT samples, with different filler fractions up to 1 wt%. It was found that oxidation reduced composite conductivity for a given concentration, shifted the percolation threshold to higher concentrations, and had no significant effect in the dielectric response.

  7. Production of Carbon Nanofibers Using a CVD Method with Lithium Fluoride as a Supported Cobalt Catalyst

    Directory of Open Access Journals (Sweden)

    S. A. Manafi

    2008-01-01

    Full Text Available Carbon nanofibers (CNFs have been synthesized in high yield (>70% by catalytic chemical vapor deposition (CCVD on Co/LiF catalyst using acetylene as carbon source. A novel catalyst support (LiF is reported for the first time as an alternative for large-scale production of carbon nanofibers while purification process of nanofibers is easier. In our experiment, the sealed furnace was heated at 700∘C for 0.5 hour (the heating rate was 10∘C/min and then cooled to room temperature in the furnace naturally. Catalytic chemical vapor deposition is of interest for fundamental understanding and improvement of commercial synthesis of carbon nanofibers (CNFs. The obtained sample was sequentially washed with ethanol, dilutes acid, and distilled water to remove residual impurities, amorphous carbon materials, and remaining of catalyst, and then dried at 110∘C for 24 hours. The combined physical characterization through several techniques, such as high-resolution transmission electron microscope (TEM, scanning electron microscope (SEM, thermogarvimetric analysis (TGA, and zeta-sizer and Raman spectroscopy, allows determining the geometric characteristic and the microstructure of individual carbon nanofibers. Catalytic chemical vapor deposition is of interest for fundamental understanding and improvement of commercial synthesis of carbon nanofibers (CNFs. As a matter of fact, the method of CCVD guarantees the production of CNFs for different applications.

  8. Bottled Water and Fluoride

    Science.gov (United States)

    ... Fluoridation Journal Articles for Community Water Fluoridation Bottled Water Recommend on Facebook Tweet Share Compartir Consumers drink ... questions about bottled water and fluoride. Does bottled water contain fluoride? Bottled water products may contain fluoride, ...

  9. Largely enhanced dielectric properties of carbon nanotubes/polyvinylidene fluoride binary nanocomposites by loading a few boron nitride nanosheets

    Science.gov (United States)

    Yang, Minhao; Zhao, Hang; He, Delong; Bai, Jinbo

    2016-08-01

    The ternary nanocomposites of boron nitride nanosheets (BNNSs)/carbon nanotubes (CNTs)/polyvinylidene fluoride (PVDF) are fabricated via a combination of solution casting and extrusion-injection processes. The effects of BNNSs on the electrical conductivity, dielectric behavior, and microstructure changes of CNTs/PVDF binary nanocomposites are systematically investigated. A low percolation value (fc) for the CNTs/PVDF binary system is obtained due to the integration of solution and melting blending procedures. Two kinds of CNTs/PVDF binary systems with various CNTs contents (fCNTs) as the matrix are discussed. The results reveal that compared with CNTs/PVDF binary systems at the same fCNTs, the ternary BNNSs/CNTs/PVDF nanocomposites exhibit largely enhanced dielectric properties due to the improvement of the CNTs dispersion state and the conductive network. The dielectric constant of CNTs/PVDF binary nanocomposite with 6 vol. % CNTs (fCNTs fc), it displays a 43.32% improvement from 1325 to 1899 after the addition of 3 vol. % BNNSs. The presence of BNNSs facilitates the formation of the denser conductive network. Meanwhile, the ternary BNNSs/CNTs/PVDF systems exhibit a low dielectric loss. The adjustable dielectric properties could be obtained by employing the ternary systems due to the microstructure changes of nanocomposites.

  10. Yttria stabilized zirconia membrane stability in molten fluoride fluxes for low-carbon magnesium production by the SOM process

    Directory of Open Access Journals (Sweden)

    Milshtein J.

    2013-01-01

    Full Text Available The Solid Oxide Membrane (SOM process for magnesium production involves the direct electrolysis of magnesium oxide for energy efficient and low-carbon magnesium production. In the SOM process, magnesium oxide is dissolved in a molten oxy-fluoride flux. An oxygen-ion-conducting SOM tube, made from yttria stabilized zirconia (YSZ, is submerged in the flux. The operating life of the electrolytic cell can be improved by understanding degradation processes in the YSZ, and one way the YSZ degrades is by yttria diffusion out of the YSZ. By adding small amounts of YF3 to the flux, yttria diffusion can be controlled. The diffusion of yttria into the flux was quantified by determining the yttria concentration profile as a function of immersion time in the flux and distance from the flux-YSZ interface. Yttria concentrations were determined using x-ray spectroscopy. The diffusion process was modeled using a numerical approach with an analytic solution to Fick’s second law. These modeling and experimental methods allowed for the determination of the optimum YF3 concentration in the flux to minimize yttria diffusion and improve membrane stability. Furthermore, the effects of common impurities in magnesium ores, such as calcium oxide, silica, and sodium oxide/sodium peroxide, on YSZ stability are being investigated.

  11. Realizing the full nanofiller enhancement in melt-spun fibers of poly(vinylidene fluoride)/carbon nanotube composites

    International Nuclear Information System (INIS)

    Strong interfacial interaction is extremely important for achieving efficient mechanical reinforcement in polymer/inorganic nanoparticle composites. In this study, it was demonstrated for the first time that largely improved interfacial interaction could be obtained in continuously melt-spun fibers of poly(vinylidene fluoride) (PVDF)/multi-walled carbon nanotube (MWCNTs) composites, just by an increasing of the deformation extent (draw ratio). The superior interaction is attributed to high deformation inducing a formation of charge-transfer-type F-C bonding between all-trans conformation PVDF chains and extended MWCNTs. As a result, a large mechanical enhancement has been achieved. For the fibers prepared at the highest draw ratio of 200, the tensile strength and modulus are improved for 235% and 109%, respectively, after adding only 0.5 wt% MWCNTs to PVDF. More importantly, a mechanical model fitting, based on the rule of mixtures, indicates that in the case of the highest draw ratio the theoretical strength of MWCNTs is comparable to its real failure strength measured directly between two opposing AFM cantilever tips (Yu et al 2000 Science 287 637). Our present study suggests a great deal of promise for achieving highly efficient CNT enhancement via the non-covalent interaction arising from simple physical fabrication like melt-spinning.

  12. Adsorption of fluoride in aqueous solutions using KMnO{sub 4}-modified activated carbon derived from steam pyrolysis of rice straw

    Energy Technology Data Exchange (ETDEWEB)

    Daifullah, A.A.M. [Hot Lab. Centre, Atomic Energy Authority, Cairo (Egypt); Yakout, S.M. [Hot Lab. Centre, Atomic Energy Authority, Cairo (Egypt)]. E-mail: yakout_2004@yahoo.com; Elreefy, S.A. [Hot Lab. Centre, Atomic Energy Authority, Cairo (Egypt)

    2007-08-17

    Fluoride in drinking water above permissible levels is responsible for human and skeletal fluorosis. In this study, activated carbons (AC) prepared by one-step steam pyrolysis of rice straw at 550, 650, 750 deg. C, respectively, were modified by liquid-phase oxidation using HNO{sub 3}, H{sub 2}O{sub 2} and KMnO{sub 4}. Characterization of these 12 carbons was made by their surface area, porosity, acidity, basicity, pH{sub pzc}, pH and ability to remove fluoride anion. Based on the data of the latter factor, the RS{sub 2}/KMnO{sub 4} carbon was selected. Along with batch adsorption studies, which involve effect of pH, adsorbate concentration, adsorbent dosage, contact time, temperature, and Co-ions (SO{sub 4} {sup 2-}, Cl{sup -}, Br{sup -}). The effects of natural organic matter (NOM) were also made to remove the fluoride from natural water. On the basis of kinetic studies, specific rate constants involved in the adsorption process using RS{sub 2}/KMnO{sub 4} carbon was calculated and second-order adsorption kinetics was observed. Equation isotherms such as Langmuir (L), Freundlich (F), Langmuir-Freundlich (LF) and Dubinin-Radushkevich (DR) were successfully used to model the experimental data. From the DR isotherm parameters, it was considered that the uptake of F{sup -} by RS{sub 2}/KMnO{sub 4} carbon proceeds by an ion-exchange mechanism (E = 10.46 kJ mol{sup -1}). The thermodynamic parameters of fluoride sorption were calculated and the sorption process was chemical in nature. The ability of RS{sub 2}/KMnO{sub 4} to remove F{sup -} from Egyptian crude phosphoric acid (P{sub 2}O{sub 5} = 48.42%) was tested and the adsorption capacity of F{sup -} in H{sub 3}PO{sub 4} was greater than that in distilled water. This is may be due to fluoride adsorption enhanced at lower pH of crude acid.

  13. Carbon monoxide oxidation on lithium fluoride supported gold nanoparticles: A significance of F-centers

    Science.gov (United States)

    Tvauri, I. V.; Gergieva, B. E.; Magkoeva, V. D.; Grigorkina, G. S.; Bliev, A. P.; Ashkhotov, O. G.; Sozaev, V. A.; Fukutani, K.; Magkoev, T. T.

    2015-07-01

    Oxidation of carbon monoxide on ultrasmall Au particles supported on LiF film has been studied by means of vibrational and thermal desorption spectroscopy. It is found that the efficiency of this process is dramatically enhanced when Au is deposited on defect LiF film obtained by electron bombardment to produce Fx--centers. Local electronic charge of the Fx- center is a key point determining formation of an (C-O-O*) intermediate on (Au-Fx-) adsorption site as carbon dioxide precursor.

  14. Divalent fluoride doped cerium fluoride scintillator

    Science.gov (United States)

    Anderson, David F.; Sparrow, Robert W.

    1991-01-01

    The use of divalent fluoride dopants in scintillator materials comprising cerium fluoride is disclosed. The preferred divalent fluoride dopants are calcium fluoride, strontium fluoride, and barium fluoride. The preferred amount of divalent fluoride dopant is less than about two percent by weight of the total scintillator. Cerium fluoride scintillator crystals grown with the addition of a divalent fluoride have exhibited better transmissions and higher light outputs than crystals grown without the addition of such dopants. These scintillators are useful in radiation detection and monitoring applications, and are particularly well suited for high-rate applications such as positron emission tomography (PET).

  15. Strontium hydroxyapatite and strontium carbonate as templates for the precipitation of calcium-phosphates in the absence and presence of fluoride

    Science.gov (United States)

    Sternitzke, Vanessa; Janousch, Markus; Heeb, Michèle B.; Hering, Janet G.; Johnson, C. Annette

    2014-06-01

    The heterogeneous precipitation of calcium-phosphates on calcium hydroxyapatite (Ca10(PO4)6(OH)2 or HAP) in the presence and absence of fluoride is important in the formation of bone and teeth, protection against tooth decay, dental and skeletal fluorosis and defluoridation of drinking water. Strontium hydroxyapatite (Sr10(PO4)6(OH)2 or SrHAP) and strontium carbonate (SrCO3) were used as calcium-free seed templates in precipitation experiments conducted with varying initial calcium-to-phosphate (Ca/P) or calcium-to-phosphate-to-fluoride (Ca/P/F) ratios. Suspensions of SrHAP or SrCO3 seed templates (which were calcium-limited for both templates and phosphate-limited in the case of SrCO3) were reacted at pH 7.3 (25 °C) over 3 days. The resulting solids were examined with Scanning Transmission Electron Microscopy (STEM), X-ray Diffraction (XRD), Fourier Transform Infrared (FTIR), and X-ray Photoelectron Spectroscopy (XPS), X-ray Absorption Near Edge Structure (XANES), and Extended X-ray Absorption Fine Structure spectroscopy (EXAFS). Calcium apatite was the predominant phase identified by all techniques independent of the added Ca/P ratios and of the presence of fluoride. It was not possible to make an unambiguous distinction between HAP and fluorapatite (Ca10(PO4)6F2, FAP). The apatite was calcium-deficient and probably contained some strontium.

  16. Tuning the Network Structure in Poly(vinylidene fluoride)/Carbon Nanotube Nanocomposites Using Carbon Black: Toward Improvements of Conductivity and Piezoresistive Sensitivity.

    Science.gov (United States)

    Ke, Kai; Pötschke, Petra; Wiegand, Niclas; Krause, Beate; Voit, Brigitte

    2016-06-01

    Piezoresistive poly(vinylidene fluoride) (PVDF) nanocomposites are very intriguing for strain sensor applications in structural health monitoring (SHM) systems. In general, high piezoresistive sensitivity combined with broad measurable strain ranges are greatly favored in those sensors. Here, a facile strategy, i.e. constructing strain susceptible conductive networks using hybrid filler systems consisting of carbon nanotubes (CNTs, 0.5-1 wt %) and carbon black (CB, 0.5-4 wt %), was introduced to tune both electrical conductivity and piezoresistive sensitivity of melt mixed PVDF nanocomposites. At the same filler content CNTs, due to their larger aspect ratio, contribute more to electrical conductivity improvements of nanocomposites than CB, while contacts between CB particles are more sensitive to tensile strain. With retained ductility of PVDF, tunable electrical conductivity and ΔR/R0-strain sensitivity can be achieved by combining the advantages of CNTs and CB by adjusting the conductive network structure. Conductivity improvement is more remarkable if the mass ratio of CNTs to CB (mCNTs/mCB), varied between 1:1 and 1:4, is higher in hybrid filler compositions. Lower mCNTs/mCB ratios result in higher ΔR/R0 values in PVDF nanocomposites whether they have the same content of total filler or similar/the same initial electrical resistivity. At 10% tensile strain, the highest ΔR/R0 of 0.65 was obtained for the nanocomposite filled with 0.5 wt % CNTs and 0.5 wt % CB, while that for the counterpart containing 1 wt % CNTs is 0.35 at the same strain. The concept of using hybrid fillers provides a low-cost and effective way to fabricate piezoresistive polymer nanocomposites toward SHM applications. PMID:27171017

  17. Metal fluorides

    International Nuclear Information System (INIS)

    Systems formed by fluorides of alkali, alkali earth, rare earth elements, yttrium, zirconium, hafnium, bismuth, antimony are investigated with the aim of preparing new fluoride materials and studying their thermodynamic and other physical and chemical properties. The respective phase diagrams are plotted. On the basis of the research fluoroberyllate glasses with rare earth additions of improved qualities (moisture resistance, crystallization resistance, resistance against radiation up to 100 Mrad) are prepared. The rho-T-x phase diagrams of the systems studied show that many compounds are sublimated congruently at certain temperatures and incongruently - above them. The existence of congruently sublimated compounds and azeotropically sublimated compositions provides for the preparation of uniform optical films. In connection with the search for new materials-luminophores and matrices of optical quantum generators - the fluoride systems of alkali metals and lanthanides are studied; the formation of binary fluorides of M3LnF6, M2LnF5, MLnF4, MLn2F7, MLn3F10 compositions is established. To search for new solid electrolytes, the solid-phase interaction of Sb-and Bi trifluorides with their oxides and alakali metal fluorides is studied. The electric conductivity of the compounds obtained is studied

  18. Fluoridation Basics

    Science.gov (United States)

    ... level in water is not enough to prevent tooth decay; however, some groundwater and natural springs can have ... the tooth’s surface, or enamel. Water fluoridation prevents tooth decay by providing frequent and consistent contact with low ...

  19. Decomposition of the fluoroethylene carbonate additive and the glue effect of lithium fluoride products for the solid electrolyte interphase: an ab initio study.

    Science.gov (United States)

    Okuno, Yukihiro; Ushirogata, Keisuke; Sodeyama, Keitaro; Tateyama, Yoshitaka

    2016-03-28

    Additives in the electrolyte solution of lithium-ion batteries (LIBs) have a large impact on the performance of the solid electrolyte interphase (SEI) that forms on the anode and is a key to the stability and durability of LIBs. We theoretically investigated effects of fluoroethylene carbonate (FEC), a representative additive, that has recently attracted considerable attention for the enhancement of cycling stability of silicon electrodes and the improvement of reversibility of sodium-ion batteries. First, we intensively examined the reductive decompositions by ring-opening, hydrogen fluoride (HF) elimination to form a vinylene carbonate (VC) additive and intermolecular chemical reactions of FEC in the ethylene carbonate (EC) electrolyte, by using density functional theory (DFT) based molecular dynamics and the blue-moon ensemble technique for the free energy profile. The results show that the most plausible product of the FEC reductive decomposition is lithium fluoride (LiF), and that the reactivity of FEC to anion radicals is found to be inert compared to the VC additive. We also investigated the effects of the generated LiF on the SEI by using two model systems; (1) LiF molecules distributed in a model aggregate of organic SEI film components (SFCs) and (2) a LiF aggregate interfaced with the SFC aggregate. DFT calculations of the former system show that F atoms form strong bindings with the Li atoms of multiple organic SFC molecules and play as a joint connecting them. In the latter interface system, the LiF aggregate adsorbs the organic SFCs through the F-Li bindings. These results suggest that LiF moieties play the role of glue in the organic SFC within the SEI film. We also examined the interface structure between a LiF aggregate and a lithiated silicon anode, and found that they are strongly bound. This strong binding is likely to be related to the effectiveness of the FEC additive in the electrolyte for the silicon anode. PMID:26948716

  20. Spinnability and Characteristics of Polyvinylidene Fluoride (PVDF-based Bicomponent Fibers with a Carbon Nanotube (CNT Modified Polypropylene Core for Piezoelectric Applications

    Directory of Open Access Journals (Sweden)

    Benjamin Glauß

    2013-07-01

    Full Text Available This research explains the melt spinning of bicomponent fibers, consisting of a conductive polypropylene (PP core and a piezoelectric sheath (polyvinylidene fluoride. Previously analyzed piezoelectric capabilities of polyvinylidene fluoride (PVDF are to be exploited in sensor filaments. The PP compound contains a 10 wt % carbon nanotubes (CNTs and 2 wt % sodium stearate (NaSt. The sodium stearate is added to lower the viscosity of the melt. The compound constitutes the fiber core that is conductive due to a percolation CNT network. The PVDF sheath’s piezoelectric effect is based on the formation of an all-trans conformation β phase, caused by draw-winding of the fibers. The core and sheath materials, as well as the bicomponent fibers, are characterized through different analytical methods. These include wide-angle X-ray diffraction (WAXD to analyze crucial parameters for the development of a crystalline β phase. The distribution of CNTs in the polymer matrix, which affects the conductivity of the core, was investigated by transmission electron microscopy (TEM. Thermal characterization is carried out by conventional differential scanning calorimetry (DSC. Optical microscopy is used to determine the fibers’ diameter regularity (core and sheath. The materials’ viscosity is determined by rheometry. Eventually, an LCR tester is used to determine the core’s specific resistance.

  1. Modeling adsorption on fluoride and application of Box–Behnken design and response surface methodology for arsenic(V removal from aqueous solution using Nano-Scale Alumina on Multi Walled Carbon Nanotube

    Directory of Open Access Journals (Sweden)

    H Zarei

    2016-01-01

    Full Text Available Objective and Background: Fluoride is an element widely found in the earth crust. Advantages and disadvantages of fluoride in the human body are depended on its concentration. Long-term consumption of drinking water contaminated with arsenic can cause adverse health effects such as skin lesions and cancer in humans. The aim of this study was to study efficiency of nano alumina on multi walled carbon nano tube  for removal As(V and fluoride from aqueous solution. Materials and Method: In this study, nano-scale crystalline alumina was synthesized on single walled carbon nanotube by sol-gel method for using as a sorbent for solid phase extraction of Fluorine ion and arsenic(V. Response surface methodology based on Box-Behnken was used to assess the effect of independent variables on the response function and prediction of the best response value. In this study, effect of different parameters, such as contact time (10 to 120 min, pH (3-9, adsorbent dosage (0.25-1.5 g/L and initial concentration of fluoride (2-8 mg/L on efficiency of process was investigated. The structure of nano-scale alumina on multi walled carbon nano tube was determined by XRD and SEM techniques. Moreover, Freundlich and Langmuir isotherm models were used to calculate equilibrium constant. Results: It was found that by increasing contact time and adsorbent dosage the rate of fluoride removal increased. However, by increasing pH and initial concentration the efficiency of fluoride removal decreased. High value for R2 (0.94 shows that removal of arsenic(V can be described by this model. The Freundlich isotherm was the best fitted graph for experimental data with R2 more than 0.997. Conclusion: In this study, it was observed that efficiency of arsenic(V and fluoride  removal was greatly increased by using nano-scale alumina on multi walled carbon nanotubes (MWCNTs.

  2. How Does Fluoride Work?

    Science.gov (United States)

    ... the mid-1940s, communities started to put more fluoride in their water supplies to protect people against tooth decay. Fluoride ... might suggest supplements — which are like vitamins containing fluoride. Just how effective is fluoridated water? Thanks to it, dentists say half of kids ...

  3. In Situ Packaging FeFx into Sack-like Carbon Nanoreactors: A Smart Way To Make Soluble Fluorides Applicable to Aqueous Batteries.

    Science.gov (United States)

    Jiang, Jian; Li, Linpo; Xu, Maowen; Zhu, Jianhui; Li, Chang Ming

    2016-02-17

    Ferruginous materials have long attracted great interest in aqueous batteries since Fe is an earth-abundant and low toxic element. However, their practical application is severely hindered by their poor structural stability during deep cycling. To maximize their cyclability, we herein propose a simple and effective method, by in situ packaging Fe-based materials into carbon nanosacks via a facile CVD approach. To verify our strategy, we purposely choose water-soluble Fe2F5 as a study paradigm. The in situ formed Fe2F5@C nanosacks product exhibits prominent anodic performance with high electrochemical activity and capacity, obviously prolonged cyclic lifetime, and outstanding rate capabilities. Besides, by pairing with the cathode of α-Co(OH)2 nanowire arrays@carbon cloth, a full device of rechargeable aqueous batteries has been developed, capable to deliver both high specific energy and power densities (Max. values reaching up to ∼163 Wh kg(-1) and ∼14.2 kW kg(-1)), which shows great potential in practical usage. Our present work may not only demonstrate the feasibility of using soluble fluorides as anodes for aqueous batteries but also provide a smart way to upgrade cyclic behaviors of Fe-based anodes. PMID:26808115

  4. Fluoride varnish or fluoride mouth rinse?

    DEFF Research Database (Denmark)

    Keller, M K; Klausen, B J; Twetman, S

    2016-01-01

    OBJECTIVE: In many Danish communities, school-based fluoride programs are offered to children with high caries risk in adjunct to tooth brushing. The purpose of this field trial was to compare the caries-preventive effectiveness of two different fluoride programs in 6-12 year olds. BASIC RESEARCH...... different schools were enrolled after informed consent and their class unit was randomly allocated to one of two fluoride programs. INTERVENTIONS: One group received a semi-annual fluoride varnish applications (FV) and the other group continued with an existing program with fluoride mouth rinses once per...... in caries development over two years among children participating in a school-based fluoride varnish or mouth rinse program....

  5. Hair as Biomarker of Fluoride Exposure in a Fluoride Endemic Area and a Low Fluoridated Area

    OpenAIRE

    Parimi, Nalini; V. Viswanath; Kashyap, Bina; Patil, Pavan Uday

    2013-01-01

    Aim: The aim of the present study was to determine whether hair could be used as biomarker of fluoride exposure. Materials and Methods: The study was carried out on 30 people living in an endemically fluoridated area and a low fluoridated area. Samples of hair from the occipital were taken and subjected to fluoride analysis by a fluoride ion electrode. Results: Lower fluoride levels in water supplies correlated with lower levels of fluoride in hair and more over higher fluoride levels in wate...

  6. Single-Step Fabrication Using a Phase Inversion Method of Poly(vinylidene fluoride) (PVDF) Activated Carbon Air Cathodes for Microbial Fuel Cells

    KAUST Repository

    Yang, Wulin

    2014-10-14

    Air cathodes used in microbial fuel cells (MFCs) need to have high catalytic activity for oxygen reduction, but they must also be easy to manufacture, inexpensive, and watertight. A simple one-step, phase inversion process was used here to construct an inexpensive MFC cathode using a poly(vinylidene fluoride) (PVDF) binder and an activated carbon catalyst. The phase inversion process enabled cathode preparation at room temperatures, without the need for additional heat treatment, and it produced for the first time a cathode that did not require a separate diffusion layer to prevent water leakage. MFCs using this new type of cathode produced a maximum power density of 1470 ± 50 mW m–2 with acetate as a substrate, and 230 ± 10 mW m–2 with domestic wastewater. These power densities were similar to those obtained using cathodes made using more expensive materials or more complex procedures, such as cathodes with a polytetrafluoroethylene (PTFE) binder and a poly(dimethylsiloxane) (PDMS) diffusion layer, or a Pt catalyst. Even though the PVDF cathodes did not have a diffusion layer, they withstood up to 1.22 ± 0.04 m of water head (∼12 kPa) without leakage, compared to 0.18 ± 0.02 m for cathodes made using PTFE binder and PDMS diffusion layer. The cost of PVDF and activated carbon ($3 m–2) was less than that of the stainless steel mesh current collector ($12 m–2). PVDF-based AC cathodes therefore are inexpensive, have excellent performance in terms of power and water leakage, and they can be easily manufactured using a single phase inversion process at room temperature.

  7. Fluoride in diet

    Science.gov (United States)

    Diet - fluoride ... bones and teeth. Too much fluoride in the diet is very rare. Rarely, infants who get too ... of essential vitamins is to eat a balanced diet that contains a variety of foods from the ...

  8. Effect of fluoride dentifrices on salivary fluoride levels in children.

    OpenAIRE

    Paul S; Tandon S; Murthy K

    1993-01-01

    Fluoride dentifrices are well accepted for their caries preventive effects. The fluoride concentration in the oral fluids after tooth brushing with fluoride dentifrices may have an important relationship to the caries reducing capacity. The present study was aimed to clinically evaluate the salivary fluoride retention of dentifrices containing low fluoride concentration in 50 children, aged 7-9 years before, during and after the use of fluoride toothpaste. Estimation of fluoride in saliva was...

  9. Fluoride glass fiber optics

    CERN Document Server

    Aggarwal, Ishwar D

    1991-01-01

    Fluoride Glass Fiber Optics reviews the fundamental aspects of fluoride glasses. This book is divided into nine chapters. Chapter 1 discusses the wide range of fluoride glasses with an emphasis on fluorozirconate-based compositions. The structure of simple fluoride systems, such as BaF2 binary glass is elaborated in Chapter 2. The third chapter covers the intrinsic transparency of fluoride glasses from the UV to the IR, with particular emphasis on the multiphonon edge and electronic edge. The next three chapters are devoted to ultra-low loss optical fibers, reviewing methods for purifying and

  10. A novel dimethyl sulfoxide/1,3-dioxolane based electrolyte for lithium/carbon fluorides batteries with a high discharge voltage plateau

    International Nuclear Information System (INIS)

    A novel dimethyl sulfoxide/1,3-dioxolane (DMSO/1,3-DO) based electrolyte is proposed for lithium/carbon fluorides (Li/CFx) batteries to enhance the discharge voltage plateau and energy density. Conductivities of the electrolyte of 1 mol L−1 LiBF4/DMSO+1,3-DO with different volume ratios are not identical, which have a maximum of 14.85 mS cm−1. From the tests of galvanostatic discharge, the discharge voltage plateau of the Li/CFx battery with an electrolyte of 1 mol L−1 LiBF4/DMSO+1,3-DO (5:5, v:v) can reach 2.69 V at 0.1 C, delivering a maximum discharge capacity of 831 mAh g−1 and the highest energy density of 2196 Wh kg−1. Compared to Li/CFx batteries with an electrolyte of 1 mol L−1 LiBF4/PC+DME (5:5, v:v), the energy density of Li/CFx batteries with an electrolyte of 1 mol L−1 LiBF4/DMSO+1,3-DO (5:5, v:v) has been improved more than 12%. With the help of XRD, SEM, TEM, EIS, FT-IR and GC-MS analysis, the results of this work suggest that DMSO/1,3-DO based electrolyte can significantly improve the discharge performance of Li/CFx batteries and keep a good electrochemical stability during discharge. The main reason for improvement of discharge performance is decreasing of both the overpotential of electrochemical polarization of CFx cathodes during discharge and the overpotential of ohmic polarization by increasing the ion conductivity of electrolyte

  11. 活性炭负载铝吸附去除水中氟离子的研究%Adsorption of Fluoride Ions from Water by Alumina Supported on Activated Carbon

    Institute of Scientific and Technical Information of China (English)

    谌任平; 汪昆平; 徐乾前

    2013-01-01

      采用载铝活性炭,通过批实验研究了对水中氟离子吸附特点,考察了负载条件、操作条件对水中氟离子吸附过程的影响。结果表明,载铝活性炭吸附水中的氟离子在24 h时达到吸附平衡;对于氟离子浓度为20 mg/L ,载铝活性炭单位当量氧化铝的氟离子吸附容量是单一活性Al2 O3吸附容量的40多倍;溶液过低或过高的pH对载铝活性炭吸附水中氟离子都有不利影响,在本实验条件下,当pH=8时载铝活性炭饱和吸附容量达到最大值;载铝活性炭对水中氟离子的吸附总体上属于放热过程,温度在30℃时已明显构成对吸附的不利影响。%Using alumina supported on activated carbon as adsorbent in batch experiments ,this paper studied the ad-sorption characteristics ,and the loading and operation conditions of adsorbents affecting the removal of fluoride in water .The results showed that the adsorption of fluoride ions by the adsorbent reached adsorption equilibrium in 24 h .For an ion concentration of 20 mg/L ,the adsorption capacity of alumina supported on activated carbon was more than 40 times as large as that of activated alumina alone .Too low or too high a pH value of the solution would have adverse effects on the adsorption of fluoride ions by alumina supported on activated carbon .Under the condi-tions of this experiment ,the saturated adsorption capacity of alumina supported on activated carbon reached the maximum at pH=8 .The adsorption of fluoride ions in water by the alumina supported on activated carbon was gen-erally exothermic ,which appeared to adversely affect the adsorption at 30℃ .

  12. Fluoride levels and osteosarcoma

    Directory of Open Access Journals (Sweden)

    Simmi Kharb

    2012-01-01

    Full Text Available Context: Osteosarcoma is a rare malignant bone tumor, commonly occurring in the age group of 10 to 24 years. Recent reports have indicated that there is a link between fluoride exposure and osteosarcoma. Aims: The present study was planned to analyze serum levels of fluoride in patients of osteosarcoma and fluoride content of their drinking water. Settings and Design: The present study was carried out comparing 10 patients of osteosarcoma and 10 healthy volunteers (who served as controls. Materials and Methods: Serum and drinking water fluoride levels were estimated by ion selective electrode. Statistical analysis used: The data were computed as mean ± SD and Student′s t test was applied. Results: Both, the serum and drinking water fluoride levels, were significant by higher in patients with osteosarcoma as compared to controls (P < 0.05, P < 0.001, respectively. Conclusions: These results suggest a link between fluoride exposure and osteosarcoma.

  13. Fluoride and Oral Health.

    Science.gov (United States)

    O'Mullane, D M; Baez, R J; Jones, S; Lennon, M A; Petersen, P E; Rugg-Gunn, A J; Whelton, H; Whitford, G M

    2016-06-01

    The discovery during the first half of the 20th century of the link between natural fluoride, adjusted fluoride levels in drinking water and reduced dental caries prevalence proved to be a stimulus for worldwide on-going research into the role of fluoride in improving oral health. Epidemiological studies of fluoridation programmes have confirmed their safety and their effectiveness in controlling dental caries. Major advances in our knowledge of how fluoride impacts the caries process have led to the development, assessment of effectiveness and promotion of other fluoride vehicles including salt, milk, tablets, toothpaste, gels and varnishes. In 1993, the World Health Organization convened an Expert Committee to provide authoritative information on the role of fluorides in the promotion of oral health throughout the world (WHO TRS 846, 1994). This present publication is a revision of the original 1994 document, again using the expertise of researchers from the extensive fields of knowledge required to successfully implement complex interventions such as the use of fluorides to improve dental and oral health. Financial support for research into the development of these new fluoride strategies has come from many sources including government health departments as well as international and national grant agencies. In addition, the unique role which industry has played in the development, formulation, assessment of effectiveness and promotion of the various fluoride vehicles and strategies is noteworthy. This updated version of 'Fluoride and Oral Health' has adopted an evidence-based approach to its commentary on the different fluoride vehicles and strategies and also to its recommendations. In this regard, full account is taken of the many recent systematic reviews published in peer reviewed literature. PMID:27352462

  14. Ionic liquid integrated multiwalled carbon nanotube in a poly(vinylidene fluoride) matrix: formation of a piezoelectric β-polymorph with significant reinforcement and conductivity improvement.

    Science.gov (United States)

    Mandal, Amit; Nandi, Arun K

    2013-02-01

    Multiwalled carbon nanotubes (MWNTs) are functionalized covalently with ionic liquid (IL, 3-aminoethyl imidazolium bromide) which helps good dispersion of IL-functionalized MWNTs (MWNT-IL) in the poly(vinylidene fluoride) (PVDF) matrix. Analysis of transmission electron microscopy (TEM) micrographs suggests ∼10 nm coating thickness of MWNTs by ILs, and the covalent linkage of ILs with MWNTs is confirmed from FT-IR and Raman spectra. PVDF nanocomposites with full β-polymorphic (piezoelectric) form are prepared using MWNT-IL by both the solvent cast and melt-blending methods. The FE-SEM and TEM micrographs indicate that IL-bound MWNTs are homogeneously dispersed within the PVDF matrix. Increasing MWNT-IL concentration in the composites results in increased β polymorph formation with a concomitant decrease of the α polymorph, and a 100% β polymorph formation occurs for 1 wt % MWNT-IL in both the fabrication conditions. A differential scanning calorimetry (DSC) study shows that the MWNT-ILs are an efficient nucleating agent for PVDF crystallization preferentially nucleating the β form due to its dipolar interactions with PVDF. The glass transition temperature (T(g)) gradually increases with an increase in MWNT-IL concentration, and the storage modulus (G') of the composites increases significantly, showing a maximum increase of 101.3% for 0.5 wt % MWNT-IL. The Young's modulus increases with MWNT-IL concentration, and analysis of the data using the Halpin-Tsai equation suggests that at low concentration they adopt an orientation parallel to the film surface; however, at higher MWNT-IL concentration it is randomly oriented. The tensile strength also increases with an increase in MWNT-IL concentration, and both the Young's modulus and the tensile strength of solvent cast films are lower than melt-blended samples. The elongation at break in the solvent cast samples shows a maximum, but in melt-blended samples it decreases continuously with increasing MWNT

  15. Fluoride Rinses, Gels and Foams

    DEFF Research Database (Denmark)

    Twetman, Svante; Keller, Mette K

    2016-01-01

    AIM: The aim of this conference paper was to systematically review the quality of evidence and summarize the findings of clinical trials published after 2002 using fluoride mouth rinses, fluoride gels or foams for the prevention of dental caries. METHODS: Relevant papers were selected after...... (6 on fluoride mouth rinse, 10 on fluoride gel and 3 on fluoride foam); 6 had a low risk of bias while 2 had a moderate risk. All fluoride measures appeared to be beneficial in preventing crown caries and reversing root caries, but the quality of evidence was graded as low for fluoride mouth rinse......, moderate for fluoride gel and very low for acidulated fluoride foam. No conclusions could be drawn on the cost-effectiveness. CONCLUSIONS: This review, covering the recent decade, has further substantiated the evidence for a caries-preventive effect of fluoride mouth rinse, fluoride gel and foam...

  16. PRODUCTION OF THORIUM FLUORIDE

    Science.gov (United States)

    Zachariasen, W.H.

    1959-08-11

    A process is presented for producing anhydrous thorium fluoride comprising the step of contacting a saturated aqueous solution of thorium nitrate with an aqueous solution of hydrofluoric acid having a concentration of about 45 to 50% by weight at a temperature above 70 deg C whereby anhydrous thorium fluoride precipitates.

  17. Fluoride varnishes and enamel caries

    NARCIS (Netherlands)

    Bruyn, Hugo de

    1987-01-01

    Topical fluoride applications have the aim of increasing the fluoride uptake in enamel and consequently reducing caries. In the early ‘60s fluoride varnishes were introduced because they had a long contact period with the enamel which resulted in a higher fluoride uptake than from other topical appl

  18. Fluoride and Water (For Parents)

    Science.gov (United States)

    ... Story" 5 Things to Know About Zika & Pregnancy Fluoride and Water KidsHealth > For Parents > Fluoride and Water Print A ... thirds of 16- to 19-year-olds continue Fluoride and the Water Supply For more than 60 years, water fluoridation ...

  19. High-fluoride groundwater.

    Science.gov (United States)

    Rao, N Subba

    2011-05-01

    Fluoride (F(-)) is essential for normal bone growth, but its higher concentration in the drinking water poses great health problems and fluorosis is common in many parts of India. The present paper deals with the aim of establishment of facts of the chemical characteristics responsible for the higher concentration of F(-) in the groundwater, after understanding the chemical behavior of F(-) in relation to pH, total alkalinity (TA), total hardness (TH), carbonate hardness (CH), non-carbonate hardness (NCH), and excess alkalinity (EA) in the groundwater observed from the known areas of endemic fluorosis zones of Andhra Pradesh that have abundant sources of F(-)-bearing minerals of the Precambrians. The chemical data of the groundwater shows that the pH increases with increase F(-); the concentration of TH is more than the concentration of TA at low F(-) groundwater, the resulting water is represented by NCH; the TH has less concentration compared to TA at high F(-) groundwater, causing the water that is characterized by EA; and the water of both low and high concentrations of F(-) has CH. As a result, the F(-) has a positive relation with pH and TA, and a negative relation with TH. The operating mechanism derived from these observations is that the F(-) is released from the source into the groundwater by geochemical reactions and that the groundwater in its flowpath is subjected to evapotranspiration due to the influence of dry climate, which accelerates a precipitation of CaCO(3) and a reduction of TH, and thereby a dissolution of F(-). Furthermore, the EA in the water activates the alkalinity in the areas of alkaline soils, leading to enrichment of F(-). Therefore, the alkaline condition, with high pH and EA, and low TH, is a more conducive environment for the higher concentration of F(-) in the groundwater.

  20. The cariostatic mechanisms of fluoride

    OpenAIRE

    Kata Rošin-Grget; Kristina Peroš; Ivana Šutej; Krešimir Bašić

    2013-01-01

    This article discusses the possible cariostatic mechanisms of the action of fluoride. In the past, fluoride inhibition of caries was ascribed to reduced solubility of enamel due to incorporation of fluoride (F–) into the enamel minerals. The present evidence from clinical and laboratory studies suggests that the caries-preventive mode of action of fluoride is mainly topical. There is convincing evidence that fluoride has a major effect on demineralisation and remineralisation of dental hard t...

  1. 载镧活性炭对水中氟离子的吸附性能研究%Study on Adsorptive Properties to Fluoride Ion of Lanthanum-loaded Activated Carbon

    Institute of Scientific and Technical Information of China (English)

    胡之阳; 唐思远; 王静; 赵亮

    2011-01-01

    Lanthanum(Ⅲ)-loaded activated carbon is prepared in the current study through acid modification followed by lanthanum impregnation.The adsorption behavior of the material to fluoride ion in water are studied through static adsorption experiment.The result shows,the solution pH values had a major impact on fluoride adsorption with optimal removal(above 96%) observed in acidic solutions,the adsorption isotherm could be well fitted by the Langmuir equation,and the estimated maximum uptake capacity is 21.4 mg/g.%通过酸改性和负载镧改性,制备出一种载镧活性炭吸附材料。采用静态吸附试验研究了该材料对水中氟离子的吸附行为。研究结果表明,该载镧活性炭吸附材料对氟离子的去除率可达到96%以上,较低的pH值有利于吸附,吸附行为符合Langmuir型吸附等温式,最大吸附容量为21.4 mg/g。

  2. Fluoride toothpastes and fluoride mouthrinses for home use

    Directory of Open Access Journals (Sweden)

    Andrew Rugg-Gunn

    2013-11-01

    Full Text Available Objective. To provide a brief commentary review of fluoride-containing toothpastes and mouthrinses with emphasis on their use at home. Toothpastes and mouthrinses are just two of many ways of providing fluoride for the prevention of dental caries. The first investigations into incorporating fluoride into toothpastes and mouthrinses were reported in the middle 1940s. Unlike water fluoridation (which is ‘automatic fluoridation’, fluoride-containing toothpastes and fluoride-containing mouthrinses are, primarily, for home use and need to be purchased by the individual. By the 1960s, research indicated that fluoride could be successfully incorporated into toothpastes and clinical trials demonstrated their effectiveness. By the end of the 1970s, almost all toothpastes contained fluoride. The widespread use of fluoride-containing toothpastes is thought to be the main reason for much improved oral health in many countries. Of the many fluoride compounds investigated, sodium fluoride, with a compatible abrasive, is the most popular, although amine fluorides are used widely in Europe. The situation is similar for mouthrinses. Concentrations of fluoride (F, commonly found, are 1500 ppm (1500 μg F/g for toothpastes and 225 ppm (225 μg F/ml for mouthrinse. Several systematic reviews have concluded that fluoride-containing toothpastes and mouthrinses are effective, and that there is added benefit from their use with other fluoride delivery methods such as water fluoridation. Guidelines for the appropriate use of fluoride toothpastes and mouthrinses are available in many countries.Conclusion. Fluoride toothpastes and mouthrinses have been developed and extensive testing has demonstrated that they are effective and their use should be encouraged.

  3. Water Fluoridation Statistics - Percent of PWS population receiving fluoridated water

    Data.gov (United States)

    U.S. Department of Health & Human Services — 2000-2014 Water Fluoridation Statistics is a biennial report of the percentage and number of people receiving fluoridated water from 2000 through 2014, originally...

  4. Prediction for new magnetoelectric fluorides

    NARCIS (Netherlands)

    Nenert, G.; Palstra, T. T. M.

    2007-01-01

    We use symmetry considerations in order to predict new magnetoelectric fluorides. In addition to these magnetoelectric properties, we discuss which among these fluorides are the ones susceptible to present multiferroic properties. We emphasize that several materials exhibit ferromagnetic properties.

  5. MOLTEN FLUORIDE NUCLEAR REACTOR FUEL

    Science.gov (United States)

    Barton, C.J.; Grimes, W.R.

    1960-01-01

    Molten-salt reactor fuel compositions consisting of mixtures of fluoride salts are reported. In its broadest form, the composition contains an alkali fluoride such as sodium fluoride, zirconium tetrafluoride, and a uranium fluoride, the latter being the tetrafluoride or trifluoride or a mixture of the two. An outstanding property of these fuel compositions is a high coeffieient of thermal expansion which provides a negative temperature coefficient of reactivity in reactors in which they are used.

  6. Magnetic interactions through fluoride

    DEFF Research Database (Denmark)

    Pedersen, Kasper Steen; Sigrist, Marc; Weihe, Høgni;

    2014-01-01

    The nature of the magnetic interaction through fluoride in a simple, dinuclear manganese(III) complex (1), bridged by a single fluoride ion in a perfectly linear fashion, is established by experiment and density functional theory. The magnitude of the antiferromagnetic exchange interaction...... and the manganese(III) zero-field-splitting parameters are unambiguously determined by inelastic neutron scattering to yield J = 33.0(2) cm(-1) (Ĥ = JŜ1·Ŝ2 Hamiltonian definition) and single-ion D = -4.0(1) cm(-1). Additionally, high-field, high-frequency electron paramagnetic resonance and magnetic measurements...... support the parameter values and resolve |E| ≈ 0.04 cm(-1). The exchange coupling constant (J) is 1 order of magnitude smaller than that found in comparable systems with linear oxide bridging but comparable to typical magnitudes through cyanide, thus underlining the potential of fluoride complexes...

  7. The effect of water purification systems on fluoride content of drinking water

    Directory of Open Access Journals (Sweden)

    Prabhakar A

    2008-03-01

    Full Text Available Objective: The purpose of the present study was to determine the effect of different water purification systems on the fluoride content of drinking water and to compare the efficacy of these water purification systems in reducing the fluoride content. Materials and Methods: Five different water purification systems were tested in this study. They were reverse osmosis, distillation, activated carbon, Reviva ® , and candle filter. The water samples in the study were of two types, viz, borewell water and tap water, these being commonly used by the people of Davangere City, Karnataka. The samples were collected before and after purification, and fluoride analysis was done using fluoride ion-specific electrode. Results: The results showed that the systems based on reverse osmosis, viz, reverse osmosis system and Reviva ® showed maximum reduction in fluoride levels, the former proving to be more effective than the latter; followed by distillation and the activated carbon system, with the least reduction being brought about by candle filter. The amount of fluoride removed by the purification system varied between the system and from one source of water to the other. Interpretation and Conclusion: Considering the beneficial effects of fluoride on caries prevention; when drinking water is subjected to water purification systems that reduce fluoride significantly below the optimal level, fluoride supplementation may be necessary. The efficacy of systems based on reverse osmosis in reducing the fluoride content of water indicates their potential for use as defluoridation devices.

  8. Fluoride retention by kaolin clay

    DEFF Research Database (Denmark)

    Kau, P. M. H.; Smith, D. W.; Binning, Philip John

    1997-01-01

    To evaluate the potential effectiveness of kaolin clay liners in storage of fluoride contaminated waste, an experimental study of the sorption and desorption behaviour of fluoride in kaolin clay was conducted. The degree of fluoride sorption by kaolin was found to depend on solution p......H and available fluoride concentration with equilibrium being achieved within 24 h. A site activation process involving the uptake of fluoride was also observed at the initial stages of sorption. This behaviour was attributed to a layer expansion process of the clay during sorption. The maximum fluoride sorption...... capacity was found to be 18.3 meq/100 g at pH 6 and 8.6 meq/100 g at pH 7. A competitive Langmuir sorption isotherm where sorption is dependant on both pH and fluoride concentration is employed to characterise the experimental sorption and desorption data. The sorption and desorption isotherms revealed...

  9. Other Fluoride Products

    Science.gov (United States)

    ... in preventing tooth decay in people of all ages. Use the information listed below to compare the other fluoride products ... even among children younger than 6 years of age. Proper application technique ... cleared for marketing by the Food and Drug Administration (FDA) as ...

  10. Salt fluoridation and oral health

    Directory of Open Access Journals (Sweden)

    Thomas M. Marthaler

    2013-11-01

    Full Text Available The aim of this paper is to make known the potential of fluoridated salt in community oral health programs, particularly in South Eastern Europe. Since 1922, the addition of iodine to salt has been successful in Switzerland. Goiter is virtually extinct. By 1945, the cariesprotective effect of fluorides was well established. Based on the success of water fluoridation, a gynecologist started adding of fluoride to salt. The sale of fluoridated salt began in 1956 in the Swiss Canton of Zurich, and several other cantons followed suit. Studies initiated in the early seventies showed that fluoride, when added to salt, inhibits dental caries. The addition of fluoride to salt for human consumption was officially authorized in 1980-82. In Switzerland 85% of domestic salt consumed is fluoridated and 67% in Germany. Salt fluoridation schemes are reaching more than one hundred million in Mexico, Colombia, Peru and Cuba. The cost of salt fluoridation is very low, within 0.02 and 0.05 € per year and capita. Children and adults of the low socio-economic strata tend to have substantially more untreated caries than higher strata. Salt fluoridation is by far the cheapest method for improving oral health. Conclusions. Salt fluoridation has cariostatic potential like water fluoridation (caries reductions up to 50%. In Europe, meaningful percentages of users have been attained only in Germany (67% and Switzerland (85%. In Latin America, there are more than 100 million users, and several countries have arrived at coverage of 90 to 99%. Salt fluoridation is by far the cheapest method of caries prevention, and billions of people throughout the world could benefit from this method.

  11. Health Effects Associated with Water Fluoridation.

    Science.gov (United States)

    Richmond, Virginia L.

    1979-01-01

    Discussion is presented concerning fluoridation of water supplies. Correlation between fluoride in drinking water and improved dental health is reviewed. Relationship is expressed between fluoridation and reduced tooth decay. Use of fluoride in treating skeletal disorders is discussed. Author advocates fluoridating water supplies. (SA)

  12. Water fluoridation and oral health

    Directory of Open Access Journals (Sweden)

    Máiréad Antoinette Harding

    2013-11-01

    Full Text Available Water fluoridation, is the controlled addition of fluoride to the water supply, with the aim of reducing the prevalence of dental caries. Current estimates suggest that approximately 370 million people in 27 countries consume fluoridated water, with an additional 50 million consuming water in which fluoride is naturally occurring. A pre-eruptive effect of fluoride exists in reducing caries levels in pit and fissure surfaces of permanent teeth and fluoride concentrated in plaque and saliva inhibits the demineralisation of sound enamel and enhances the remineralisation of demineralised enamel. A large number of studies conducted worldwide demonstrate the effectiveness of water fluoridation. Objections to water fluoridation have been raised since its inception and centre mainly on safety and autonomy. Systematic reviews of the safety and efficacy of water fluoridation attest to its safety and efficacy; dental fluorosis identified as the only adverse outcome. Conclusion: Water fluoridation is an effective safe means of preventing dental caries, reaching all populations, irrespective of the presence of other dental services. Regular monitoring of dental caries and fluorosis is essential particularly with the lifelong challenge which dental caries presents.

  13. Magnesium fluoride recovery method

    Science.gov (United States)

    Gay, Richard L.; McKenzie, Donald E.

    1989-01-01

    A method of obtaining magnesium fluoride substantially free from radioactive uranium from a slag containing the same and having a radioactivity level of at least about 7000 pCi/gm. The slag is ground to a particle size of about 200 microns or less. The ground slag is contacted with an acid under certain prescribed conditions to produce a liquid product and a particulate solid product. The particulate solid product is separated from the liquid and treated at least two more times with acid to produce a solid residue consisting essentially of magnesium fluoride substantially free of uranium and having a residual radioactivity level of less than about 1000 pCi/gm. In accordance with a particularly preferred embodiment of the invention a catalyst and an oxidizing agent are used during the acid treatment and preferably the acid is sulfuric acid having a strength of about 1.0 Normal.

  14. Fluoride in dental erosion

    OpenAIRE

    Magalhães, A C; Wiegand, A.; Rios, D.; Buzalaf, M.A.R.; Lussi, A.

    2011-01-01

    Dental erosion develops through chronic exposure to extrinsic/intrinsic acids with a low pH. Enamel erosion is characterized by a centripetal dissolution leaving a small demineralized zone behind. In contrast, erosive demineralization in dentin is more complex as the acid-induced mineral dissolution leads to the exposure of collagenous organic matrix, which hampers ion diffusion and, thus, reduces further progression of the lesion. Topical fluoridation inducing the formation of a protective l...

  15. Diffuso-Kinetics and Diffuso-Mechanics of Carbon Dioxide / Polyvinylidene Fluoride System under Explosive Gas Decompression: Identification of Key Diffuso-Elastic Couplings by Numerical and Experimental Confrontation

    Directory of Open Access Journals (Sweden)

    Grandidier Jean-Claude

    2015-02-01

    Full Text Available The work aims at identifying the key diffuso-elastic couplings which characterize a numerical tool developed to simulate the irreversible ‘Explosive Decompression Failure’ (XDF in semi-crystalline polymer. The model proposes to predict the evolution of the gas concentration and of the stress field in the polymer during the gas desorption [DOI: 10.1016/j.compositesa.2005.05.021]. Main difficulty is to couple thermal, mechanical and diffusive effects that occur simultaneously during the gas desorption. The couplings are splitting into two families: indirect coupling (i.e., phenomenology that is state variables (gas concentration, temperature, and pressure dependent. direct coupling, (i.e., diffuso-elastic coupling as polymer volume changes because of gas diffusion; The numerical prediction of the diffusion kinetics and of the volume strain (swelling of PVF2 (polyvinylidene fluoride under CO2 (carbon dioxide environment is concerned. The prediction is carried out by studying selected combinations of couplings for a broad range of CO2 pressures. The modeling relevance is evaluated by a comparison with experimental transport parameters analytically identify from solubility tests. A pertinent result of the present study is to have demonstrated the non-uniqueness of the coefficients of diffusion (D and solubility (Sg between the diffuso-elastic coupling (direct coupling and indirect coupling. Main conclusion is that it is necessary to consider concomitantly the two types of couplings, the indirect and the direct couplings.

  16. Mesoporous zeolite and zeotype single crystals synthesized in fluoride media

    DEFF Research Database (Denmark)

    Egeblad, Kresten; Kustova, Marina; Klitgaard, Søren Kegnæs;

    2007-01-01

    We report the synthesis and characterization of a series of new mesoporous zeolite and zeotype materials made available by combining new and improved procedures for directly introducing carbon into reaction mixtures with the fluoride route for conventional zeolite synthesis. The mesoporous...... characterized by XRPD, SEM, TEM and N-2 physisorption measurements. For the zeolite materials it A as found that mesoporous MFI and MEL structured single crystals could indeed be crystallized from fluoride media using an improved carbon-templating approach. More importantly, it was found that mesoporous BEA......-type single crystals could be crystallized from fluoride media by a newly developed procedure presented here. Thus, we here present the only known route to mesoporous BEA-type single crystals, since crystallization of this framework structure from basic media is known to give only nanosized crystals...

  17. Preparation of mixed rare earths modified chitosan for fluoride adsorption

    Institute of Scientific and Technical Information of China (English)

    梁鹏; 张艺; 汪东风; 徐莹; 罗斓

    2013-01-01

    This paper described the fluoride removal from water using a new adsorbent namely mixed rare earths modified chitosan (CR). Mixed rare earths mainly contained La followed by Ce which was analyzed by inductively coupled plasma mass spectrometry (ICP-MS). La(III)-modified chitosan (CL) was also prepared as control. For the batch technique, the effects of various parameters such as contact time, pH, adsorbent dose, initial fluoride concentration and co-ions on fluoride adsorption were studied. Fourier trans-form infrared spectroscopy (FTIR) and X-ray diffraction (XRD) were used to characterize adsorbents. It was observed that the fluo-ride adsorption capacity of CR (3.72 mgF-/g) was higher than CL (3.16 mgF-/g) at 2 h. The presence of co-ions such as bicarbonate and carbonate greatly affected the fluoride adsorption from water. Characterization experiments indicated the successful chelation between mixed rare earths and chitosan. The possible fluoride adsorption mechanism of CR was explained by a chemical reaction.

  18. Treatability study of arsenic, fluoride and nitrate from drinking water by adsorption process

    International Nuclear Information System (INIS)

    Natural contamination of nitrate, fluoride, arsenic and dissolved salts in ground water sources is the main health menace at present in different parts of Pakistan. The metalloids especially arsenic, fluoride and nitrate pose severe health hazards to human being. The present research work investigated the removal techniques for arsenic, fluoride and nitrate from drinking water by adsorption process. Ion exchange resins, activated carbon and activated alumina were used for removal of selected contaminants. These adsorbents were evaluated by comparing their removal efficiency as well as requisite operator skills. The result of activated alumina was found good as compared to activated carbon, mix bed resins and ion exchange resins (IRA-400) for maximum removal of arsenic, nitrate and fluoride. The removal efficiency of arsenic, fluoride and nitrate were found 96%, 99%, 98% respectively in case of activated alumina. The advantage of adsorption process is easy to use and relatively cheaper as compared to other treatment methodologies. (author)

  19. Private Well Water and Fluoride

    Science.gov (United States)

    ... it is the responsibility of the homeowner to know and understand the quality of the water from their well. The U.S. ... or area. Additional information on testing well water quality in private wells ... do I need to know about fluoride and groundwater from a well? Fluoride ...

  20. Prediction for new magnetoelectric fluorides

    OpenAIRE

    Nenert, G.; Palstra, T. T. M.

    2007-01-01

    We use symmetry considerations in order to predict new magnetoelectric fluorides. In addition to these magnetoelectric properties, we discuss which among these fluorides are the ones susceptible to present multiferroic properties. We emphasize that several materials exhibit ferromagnetic properties. This ferromagnetism should enhance the interplay between the magnetic and dielectric properties in these materials.

  1. WET FLUORIDE SEPARATION METHOD

    Science.gov (United States)

    Seaborg, G.T.; Gofman, J.W.; Stoughton, R.W.

    1958-11-25

    The separation of U/sup 233/ from thorium, protactinium, and fission products present in neutron-irradiated thorium is accomplished by dissolving the irradiated materials in aqueous nitric acid, adding either a soluble fluoride, iodate, phosphate, or oxalate to precipltate the thorium, separating the precipltate from the solution, and then precipitating uranlum and protactinium by alkalizing the solution. The uranium and protactinium precipitate is removcd from the solution and dissolved in nitric acid. The uranyl nitrate may then be extracted from the acid solution by means of ether, and the protactinium recovered from the aqueous phase.

  2. Urinary Fluoride Concentration in Children with Disabilities Following Long-Term Fluoride Tablet Ingestion

    Science.gov (United States)

    Liu, Hsiu-Yueh; Chen, Jung-Ren; Hung, Hsin-Chia; Hsiao, Szu-Yu; Huang, Shun-Te; Chen, Hong-Sen

    2011-01-01

    Urine is the most commonly utilized biomarker for fluoride excretion in public health and epidemiological studies. Approximately 30-50% of fluoride is excreted from urine in children. Urinary fluoride excretion reflects the total fluoride intake from multiple sources. After administering fluoride tablets to children with disabilities, urinary…

  3. 49 CFR 173.163 - Hydrogen fluoride.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrogen fluoride. 173.163 Section 173.163... Hydrogen fluoride. (a) Hydrogen fluoride (hydrofluoric acid, anhydrous) must be packaged as follows: (1) In... filling ratio of 0.84. (b) A cylinder removed from hydrogen fluoride service must be condemned...

  4. Molten fluoride fuel salt chemistry

    International Nuclear Information System (INIS)

    The chemistry of molten fluorides is traced from their development as fuels in the Molten Salt Reactor Experiment with important factors in their selection being discussed. Key chemical characteristics such as solubility, redox behavior, and chemical activity are explained as they relate to the behavior of molten fluoride fuel systems. Fission product behavior is described along with processing experience. Development requirements for fitting the current state of the chemistry to modern nuclear fuel system are described. It is concluded that while much is known about molten fluoride behavior, processing and recycle of the fuel components is a necessary factor if future systems are to be established

  5. Geochemical evaluation of fluoride contamination of groundwater in the Thoothukudi District of Tamilnadu, India

    Science.gov (United States)

    Singaraja, C.; Chidambaram, S.; Anandhan, P.; Prasanna, M. V.; Thivya, C.; Thilagavathi, R.; Sarathidasan, J.

    2014-09-01

    Fluoride is a chemical element that has been shown to cause significant effects on human health through drinking water. Different forms of fluoride exposure are of importance and have shown to affect the body's fluoride content and thus increasing the risks of fluoride-prone diseases. Fluoride has beneficial effects on teeth; however, low concentrations of fluoride intensify the risk of tooth decay. Fluoride can also be quite detrimental at higher concentrations at skeletal fluorosis. The Thoothukudi District is a hard rock and alluvial plain marked as one of the Fluoride-increase area in Tamilnadu due to occurrence of various rock types including fluoride-bearing minerals. The F- content of groundwater can thus originate from the dissolution of Fluoride-bearing minerals in the bed rock. Hundred representative groundwater samples from Thoothukudi District were collected during two different seasons. Samples were analysed for F-, other major cations and anions. The study area is chiefly composed of hornblende biotite gneiss, charnockite, alluvio marine, fluvial marine and granite with small patches of quartzite and sandstone. Higher concentration of fluoride is observed during pre-monsoon (3.3 mg l-1) compared to the post-monsoon (2.4 mg l-1) due to the dilution effect. Spatial distribution and factor score show that higher concentrations of F- are noted in the north and central part of the study area owing to lithology. Bicarbonate is well correlated with F- which explains that both ions were derived from the weathering. While F- has a very weak correlation with pH which may be due to the increase of alkalinity resulting from the increase of carbonate and bicarbonate ions.

  6. Fluoride glass: Crystallization, surface tension

    Science.gov (United States)

    Doremus, R. H.

    1988-01-01

    Fluoride glass was levitated acoustically in the ACES apparatus on STS-11, and the recovered sample had a different microstructure from samples cooled in a container. Further experiments on levitated samples of fluoride glass are proposed. These include nucleation, crystallization, melting observations, measurement of surface tension of molten glass, and observation of bubbles in the glass. Ground experiments are required on sample preparation, outgassing, and surface reactions. The results should help in the development and evaluation of containerless processing, especially of glass, in the development of a contaminent-free method of measuring surface tensions of melts, in extending knowledge of gas and bubble behavior in fluoride glasses, and in increasing insight into the processing and properties of fluoride glasses.

  7. Method of aluminium fluoride manufacture

    International Nuclear Information System (INIS)

    The manufacture of aluminium fluoride is based on waste processing in uranium hexafluoride conversion to uranium oxides within the fuel cycle. The conversion is the stoichiometric conversion of uranium hexafluoride with aluminium nitrate to uranyl nitrate. This is extracted from the water phase by phosphoric acid trialkyl ester to an organic solvent and further processed. The discharge water phase is solidified by evaporation to solid aluminium fluoride and nitric acid. (M.S.)

  8. FLUORIDE TOXICITY – A HARSH REALITY

    Directory of Open Access Journals (Sweden)

    Bandlapalli Pavani

    2011-04-01

    Full Text Available There are many incidents of fluoride toxicity whether it is acute or chronic. Fluoride toxicity is an environmental hazard which arises from the upper layers of geological crust and is dissolved in water. Prolonged drinking of such water causes chronic fluoride toxicity. Use of fluoride containing compounds for various purposes such as dental products, metal, glass, refrigerator and chemical industries act as a source of fluoride poisoning and increase the risk of toxicity. This review reflects the deleterious effects of fluorides on various organs in the physiological system.

  9. An Overview of Liquid Fluoride Salt Heat Transport Systems

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, David Eugene [ORNL; Cetiner, Sacit M [ORNL

    2010-09-01

    Heat transport is central to all thermal-based forms of electricity generation. The ever increasing demand for higher thermal efficiency necessitates power generation cycles transitioning to progressively higher temperatures. Similarly, the desire to provide direct thermal coupling between heat sources and higher temperature chemical processes provides the underlying incentive to move toward higher temperature heat transfer loops. As the system temperature rises, the available materials and technology choices become progressively more limited. Superficially, fluoride salts at {approx}700 C resemble water at room temperature being optically transparent and having similar heat capacity, roughly three times the viscosity, and about twice the density. Fluoride salts are a leading candidate heat-transport material at high temperatures. Fluoride salts have been extensively used in specialized industrial processes for decades, yet they have not entered widespread deployment for general heat transport purposes. This report does not provide an exhaustive screening of potential heat transfer media and other high temperature liquids such as alkali metal carbonate eutectics or chloride salts may have economic or technological advantages. A particular advantage of fluoride salts is that the technology for their use is relatively mature as they were extensively studied during the 1940s-1970s as part of the U.S. Atomic Energy Commission's program to develop molten salt reactors (MSRs). However, the instrumentation, components, and practices for use of fluoride salts are not yet developed sufficiently for commercial implementation. This report provides an overview of the current understanding of the technologies involved in liquid salt heat transport (LSHT) along with providing references to the more detailed primary information resources. Much of the information presented here derives from the earlier MSR program. However, technology has evolved over the intervening years

  10. High dielectric permittivity and improved mechanical and thermal properties of poly(vinylidene fluoride) composites with low carbon nanotube content: effect of composite processing on phase behavior and dielectric properties

    Science.gov (United States)

    Sudheer Kumar, G.; Vishnupriya, D.; Chary, K. Suresh; Umasankar Patro, T.

    2016-09-01

    The composite processing technique and nanofiller concentration and its functionalization significantly alter the properties of polymer nanocomposites. To realize this, multi-walled carbon nanotubes (CNT) were dispersed in a poly(vinylidene fluoride) (PVDF) matrix at carefully selected CNT concentrations by two illustrious methods, such as solution-cast and melt-mixing. Notwithstanding the processing method, CNTs induced predominantly the γ-phase in PVDF, instead of the commonly obtained β-phase upon nanofiller incorporation, and imparted significant improvements in dielectric properties. Acid-treatment of CNT improved its dispersion and interfacial adhesion significantly with PVDF, and induced a higher γ-phase content and better dielectric properties in PVDF as compared to pristine CNT. Further, the γ-phase content was found to be higher in solution-cast composites than that in melt-mixed counterparts, most likely due to solvent-induced crystallization in a controlled environment and slow solvent evaporation in the former case. However, interestingly, the melt-mixed composites showed a significantly higher dielectric constant at the onset of the CNT networked-structure as compared to the solution-cast composites. This suggests the possible role of CNT breakage during melt-mixing, which might lead to higher space-charge polarization at the polymer–CNT interface, and in turn an increased number of pseudo-microcapacitors in these composites than the solution-cast counterparts. Notably, PVDF with 0.13 vol% (volume fraction, f c = 0.0013) of acid-treated CNTs, prepared by melt-mixing, displayed the relative permittivity of ∼217 and capacitance of ∼5430 pF, loss tangent of ∼0.4 at 1 kHz and an unprecedented figure of merit of ∼105. We suggest a simple hypothesis for the γ-phase formation and evolution of the high dielectric constant in these composites. Further, the high-dielectric composite film showed marked improvements in mechanical and thermal

  11. High dielectric permittivity and improved mechanical and thermal properties of poly(vinylidene fluoride) composites with low carbon nanotube content: effect of composite processing on phase behavior and dielectric properties

    Science.gov (United States)

    Sudheer Kumar, G.; Vishnupriya, D.; Chary, K. Suresh; Umasankar Patro, T.

    2016-09-01

    The composite processing technique and nanofiller concentration and its functionalization significantly alter the properties of polymer nanocomposites. To realize this, multi-walled carbon nanotubes (CNT) were dispersed in a poly(vinylidene fluoride) (PVDF) matrix at carefully selected CNT concentrations by two illustrious methods, such as solution-cast and melt-mixing. Notwithstanding the processing method, CNTs induced predominantly the γ-phase in PVDF, instead of the commonly obtained β-phase upon nanofiller incorporation, and imparted significant improvements in dielectric properties. Acid-treatment of CNT improved its dispersion and interfacial adhesion significantly with PVDF, and induced a higher γ-phase content and better dielectric properties in PVDF as compared to pristine CNT. Further, the γ-phase content was found to be higher in solution-cast composites than that in melt-mixed counterparts, most likely due to solvent-induced crystallization in a controlled environment and slow solvent evaporation in the former case. However, interestingly, the melt-mixed composites showed a significantly higher dielectric constant at the onset of the CNT networked-structure as compared to the solution-cast composites. This suggests the possible role of CNT breakage during melt-mixing, which might lead to higher space-charge polarization at the polymer-CNT interface, and in turn an increased number of pseudo-microcapacitors in these composites than the solution-cast counterparts. Notably, PVDF with 0.13 vol% (volume fraction, f c = 0.0013) of acid-treated CNTs, prepared by melt-mixing, displayed the relative permittivity of ˜217 and capacitance of ˜5430 pF, loss tangent of ˜0.4 at 1 kHz and an unprecedented figure of merit of ˜105. We suggest a simple hypothesis for the γ-phase formation and evolution of the high dielectric constant in these composites. Further, the high-dielectric composite film showed marked improvements in mechanical and thermal properties

  12. High dielectric permittivity and improved mechanical and thermal properties of poly(vinylidene fluoride) composites with low carbon nanotube content: effect of composite processing on phase behavior and dielectric properties.

    Science.gov (United States)

    Kumar, G Sudheer; Vishnupriya, D; Chary, K Suresh; Patro, T Umasankar

    2016-09-23

    The composite processing technique and nanofiller concentration and its functionalization significantly alter the properties of polymer nanocomposites. To realize this, multi-walled carbon nanotubes (CNT) were dispersed in a poly(vinylidene fluoride) (PVDF) matrix at carefully selected CNT concentrations by two illustrious methods, such as solution-cast and melt-mixing. Notwithstanding the processing method, CNTs induced predominantly the γ-phase in PVDF, instead of the commonly obtained β-phase upon nanofiller incorporation, and imparted significant improvements in dielectric properties. Acid-treatment of CNT improved its dispersion and interfacial adhesion significantly with PVDF, and induced a higher γ-phase content and better dielectric properties in PVDF as compared to pristine CNT. Further, the γ-phase content was found to be higher in solution-cast composites than that in melt-mixed counterparts, most likely due to solvent-induced crystallization in a controlled environment and slow solvent evaporation in the former case. However, interestingly, the melt-mixed composites showed a significantly higher dielectric constant at the onset of the CNT networked-structure as compared to the solution-cast composites. This suggests the possible role of CNT breakage during melt-mixing, which might lead to higher space-charge polarization at the polymer-CNT interface, and in turn an increased number of pseudo-microcapacitors in these composites than the solution-cast counterparts. Notably, PVDF with 0.13 vol% (volume fraction, f c  = 0.0013) of acid-treated CNTs, prepared by melt-mixing, displayed the relative permittivity of ∼217 and capacitance of ∼5430 pF, loss tangent of ∼0.4 at 1 kHz and an unprecedented figure of merit of ∼10(5). We suggest a simple hypothesis for the γ-phase formation and evolution of the high dielectric constant in these composites. Further, the high-dielectric composite film showed marked improvements in mechanical and thermal

  13. Industrial fluoride pollution. Chronic fluoride poisoning in Cornwall Island cattle.

    Science.gov (United States)

    Krook, L; Maylin, G A

    1979-04-01

    An aluminum plant on the south bank of the St. Lawrence river, southwest of Cornwall Island, Ontario, Canada, has emitted 0.816 metric tons of fluoride daily since 1973; considerably higher amounts were emitted from 1959 to 1973. The plant has been designated as the "major source of fluoride emissions impacting on Cornwall Island." Chronic fluoride poisoning in Cornwall island cattle was manifested clinically by stunted growth and dental fluorosis to a degree of severe interference with drinking and mastication. Cows died at or were slaughtered after the third pregnancy. The deterioration of cows did not allow further pregnancies. Fluoride concentrations in ash of biopsied coccygeal vertebrae increased significantly with age and were dependent on distance from and direction to the aluminum plant. Fluoride in bone ash of a 7-month old-fetus exceeded 500 ppm; fluoride thus was passed transplacentally. Analyses of fluoride in ash of bones obtained at necropsy of cattle from 4 months of age to 4 to 5 years of age showed increased amounts with age. Cancellous bone retained far higher amounts than cortical bone, a reflection of the normally higher metabolic rate of cancellous bone. Concentrations exceeding 10,000 ppm fluoride were recorded in cancellous bone of a 4-to 5-year-old cow. The target cells for fluoride in chronic fluorosis were shown to be the ameloblasts, the dental pulp cells and the odontoblasts and, in bone, primarily the resorbing osteocytes and also the osteoblasts. Atrophy and necrosis of the ameloblasts were responsible for enamel defects. The existing enamel showed brown discoloration from fluoride deposits. The pulp cells underwent fibrous and osseous metaplasia and necrosis of the ectopic bone occurred. The odontoblasts were atrophic and the dentin showed brown discoloration. The resorbing osteocytes were inactive and osteosclerosis resulted. This was especially pronounced in areas of normally great apposition, i.e. in the metaphyses. The epiphyseal

  14. Fluoride level in saliva after bonding orthodontic brackets with a fluoride containing adhesive

    NARCIS (Netherlands)

    Ogaard, B; Arends, J; Helseth, H; Dijkman, G; vanderKuijl, M

    1997-01-01

    The fluoride level in saliva is considered an important parameter in caries prevention. Elevation of the salivary fluoride level by a fluoride-releasing orthodontic bonding adhesive would most likely be beneficial in the prevention of enamel caries. In this study, the fluoride level in saliva was me

  15. Fluoridering af drikkevandet i Danmark?

    DEFF Research Database (Denmark)

    Arvin, Erik; Spliid, Henrik; Bruvo, M.;

    2010-01-01

    Første gang sammenhængen mellem caries (huller i tænderne) og fluoridindholdet i drikkevand blev diskuteret i vandværkskredse i Danmark var ved årsmødet i 1958. Her blev det oplyst, at fluorid i drikkevand beskytter mod caries, men man konstaterede også, at der nok ikke var stemning for fluorid......-tilsætning til drikkevandet (fluoridering). Siden da er emnet ikke taget op. Formålet med dette indlæg er at besvare spørgsmålene: 1. Er der behov for fluoridering af drikkevandet i Danmark? 2. Er der alternativer? Hvordan påvirker blødgøring af vand og andre vandbehandlingsmetoder dental caries hos børn og unge......? Som baggrund herfor vil vi redegøre for resultaterne af et netop afsluttet studium af sammenhængen mellem caries og drikkevandets sammensætning, specielt m.h.t. luoridindholdet og vandets calciumindhold (hårdhed). Undersøgelsen bekræfter, at fluorid i drikkevand i væsentlig grad beskytter mod caries...

  16. Nickel-Catalyzed Dimerization and Alkylarylation of 1,3-Dienes with Alkyl Fluorides and Aryl Grignard Reagents.

    Science.gov (United States)

    Iwasaki, Takanori; Min, Xin; Fukuoka, Asuka; Kuniyasu, Hitoshi; Kambe, Nobuaki

    2016-04-25

    In the presence of a nickel catalyst, 1,3-butadiene undergoes selective dimerization and alkylarylation with alkyl fluorides and aryl Grignard reagents to give 1,6-octadienes with alkyl and aryl groups at the 3- and 8-positions, respectively, by the consecutive formation of three carbon-carbon bonds. The formation of an anionic nickel complex plays an important role in forming C-C bonds with alkyl fluorides. PMID:26938137

  17. Acute toxicity of uranium hexafluoride, uranyl fluoride and hydrogen fluoride

    International Nuclear Information System (INIS)

    Uranium hexafluoride (UF6) released into the atmosphere will react rapidly with moisture in the air to form the hydrolysis products uranyl fluoride (UO2F2) and hydrogen fluoride (HF). Uranium compounds such as UF6 and UO2F2 exhibit both chemical toxicity and radiological effects, while HF exhibits only chemical toxicity. This paper describes the development of a methodology for assessing the human health consequences of a known acute exposure to a mixture of UF6, UO2F2, and HF. 4 refs., 2 figs., 5 tabs

  18. Fluoride: its role in dentistry

    Directory of Open Access Journals (Sweden)

    Livia Maria Andaló Tenuta

    2010-01-01

    Full Text Available In spite of decades of research on fluoride and the recognition of its role as the cornerstone of dental caries reduction in the last fifty years, questions still arise on its use at community, self-applied and professional application levels. Which method of fluoride delivery should be used? How and when should it be used? How can its benefits be maximized and still reduce the risks associated with its use? These are only some of the challenging questions facing us daily. The aim of this paper is to present scientific background to understand the importance of each method of fluoride use considering the current caries epidemiological scenario, and to discuss how individual or combined methods can be used based on the best evidence available.

  19. Molten fluorides for nuclear applications

    Directory of Open Access Journals (Sweden)

    Sylvie. Delpech

    2010-12-01

    Full Text Available The importance of pyrochemistry is being increasingly acknowledged and becomes unavoidable in the nuclear field. Molten salts may be used for fuel processing and spent fuel recycling, for heat transfer, as a homogeneous fuel and as a breeder material in fusion systems. Fluorides that are stable at high temperature and under high neutron flux are especially promising. Analysis of several field cases reveals that corrosion in molten fluorides is essentially due to the oxidation of metals by uranium fluoride and/or oxidizing impurities. The thermodynamics of this process are discussed with an emphasis on understanding the mass transfer in the systems, selecting appropriate metallic materials and designing effective purification methods.

  20. Fluoride in African groundwater: Occurrence and mitigation

    NARCIS (Netherlands)

    Vasak, S.; Griffioen, J.; Feenstra, L.

    2010-01-01

    Fluoride in groundwater has both natural and anthropogenic sources. Fluoride bearing minerals, volcanic gases and various industrial and agricultural activities can contribute to high concentrations. High intake of fluoride from drinking water is the main cause of fluorosis and may lead to many othe

  1. METHOD OF PREPARING METAL FLUORIDES

    Science.gov (United States)

    Katz, J.J.; Sheft, I.

    1959-08-11

    A method is presented for preparing the halides of elements which are relatively non-reactive with halogenating agents. The method involves reacting a mixture of an oxygen containing salt of a difficulty halogenated metal with an oxygen containing salt of an easily halogenated metal with a halogenating agent. Accordingly plutonium tetrafluoride is produced by reacting a mixture of plutonium dioxide and uranium octaoxide with bromine trifluoride. The reaction proceeds smoothly at moderate temperatures and the resulting plutonium trifluoride may be readily separated from many impurities which form volatile fluorides by volatilizing these volatile fluorides from the reaction chamber.

  2. Mechanism of Calcium Fluoride Acceleration for Vacuum Carbothermic Reduction of Magnesia

    Science.gov (United States)

    Jiang, Yun; Liu, Yu-qin; Ma, Hong-wen; Zhou, Wei-gong

    2016-04-01

    The use of a small amount of calcium fluoride as an additive greatly accelerated the reduction of magnesia during the preparation of magnesium from magnesia using the vacuum carbothermic reduction method. At 1573 K (1300 °C), the magnesia reaction rates of the samples with 1, 3, and 5 pct CaF2 were all approximately 26 pct, three times that of free CaF2, and they were arranged in order of the calcium fluoride weight percentages at 1673 K (1400 °C). The residues were analyzed using chemical analysis, XRD, SEM, EDS, and XRF. The possible acceleration mechanism was discussed. Calcium fluoride combined with magnesia and silicon dioxide to form a eutectic that melted as a channel to aid the solid-solid reaction between carbon and magnesia at approximately 1573 K (1300 °C). Calcium fluoride in the molten state offered free calcium ions and fluorine ions. Fluorine ions entered and distorted the magnesia crystal lattice. The structural strength and chemical stability of the magnesia crystal lattice decreased, which facilitated the magnesia reduction by carbon. Calcium ions were employed to generate the calcium and magnesium silicate. The easyly evaporating fluorides, including magnesium fluoride and silicon tetrafluoride, were regarded as the main reason for the loss of fluorine.

  3. Fluoride remediation using floating macrophytes

    Directory of Open Access Journals (Sweden)

    Naba Kumar Mondal

    2014-04-01

    Full Text Available Six aquatic macrophytes, such as Pistia stratiotes, Ceratophyllum demersum, Nymphoides indica, Lemna major, Azolla pinnata,and Eichhornia crassipes were considered for remove fluoride from aqueous solution. Five different concentrations (10, 30, 50, and 100 ppm of fluoride solution were taken in 1 L plastic container. Fixed weight (20 g of macrophytes along with 500 ml fluoride solution was taken in each plastic container for 72 hours observation. Results demonstrated all the macrophytes show highest fluoride removal during 24 h to 48 h, but after 72 h their efficiency reduced drastically. The species N. indica showed better removal efficiency than other experimental macrophytes. In general, pigment measurement data indicated higher concentration at 72 h. However, Pistia sp. showed higher concentration of pigmentation at intermediate time interval (48 h. Higher level of dry weight to fresh weight ratio was recorded for L. major and A. pinnata at all concentrations, excepting at 10 ppm. In addition, all macrophytes showed lower RGR at higher concentration. Isotherm study indicated that macrophyte C. demersum is a good fitted with Freundlich and Langmuir isotherm whereas L. major with Langmuir isotherm during 24 hours.

  4. Special Report: Fluoridation of Water.

    Science.gov (United States)

    Hileman, Bette

    1988-01-01

    Reviews the controversy regarding water fluoridation in the United States during the last 50 years. Discusses the current status; benefits; and health risks including skeletal fluorosis, kidney disease, hypersensitivity, mutagenic effects, birth defects, and cancer. Presents statistics and anecdotal accounts. (CW)

  5. Alimentary fluoride intake in preschool children

    Directory of Open Access Journals (Sweden)

    Lencova Erika

    2011-10-01

    Full Text Available Abstract Background The knowledge of background alimentary fluoride intake in preschool children is of utmost importance for introducing optimal and safe caries preventive measures for both individuals and communities. The aim of this study was to assess the daily fluoride intake analyzing duplicate samples of food and beverages. An attempt was made to calculate the daily intake of fluoride from food and swallowed toothpaste. Methods Daily alimentary fluoride intake was measured in a group of 36 children with an average age of 4.75 years and an average weight of 20.69 kg at baseline, by means of a double plate method. This was repeated after six months. Parents recorded their child's diet over 24 hours and collected duplicated portions of food and beverages received by children during this period. Pooled samples of food and beverages were weighed and solid food samples were homogenized. Fluoride was quantitatively extracted from solid food samples by a microdiffusion method using hexadecyldisiloxane and perchloric acid. The content of fluoride extracted from solid food samples, as well as fluoride in beverages, was measured potentiometrically by means of a fluoride ion selective electrode. Results Average daily fluoride intake at baseline was 0.389 (SD 0.054 mg per day. Six months later it was 0.378 (SD 0.084 mg per day which represents 0.020 (SD 0.010 and 0.018 (SD 0.008 mg of fluoride respectively calculated per kg bw/day. When adding the values of unwanted fluoride intake from the toothpaste shown in the literature (0.17-1.21 mg per day the estimate of the total daily intake of fluoride amounted to 0.554-1.594 mg/day and recalculated to the child's body weight to 0.027-0.077 mg/kg bw/day. Conclusions In the children studied, observed daily fluoride intake reached the threshold for safe fluoride intake. When adding the potential fluoride intake from swallowed toothpaste, alimentary intake reached the optimum range for daily fluoride intake

  6. Fluoride retention in saliva and in dental biofilm after different home-use fluoride treatments.

    Science.gov (United States)

    Souza, Daniela Correia Cavalcante; Maltz, Marisa; Hashizume, Lina Naomi

    2014-01-01

    This single-blind, randomized, crossover study aimed at assessing the long-term fluoride concentrations in saliva and in dental biofilm after different home-use fluoride treatments. The study volunteers (n = 38) were residents of an area with fluoridated drinking water. They were administered four treatments, each of which lasted for one week: twice-daily placebo dentifrice, twice-daily fluoride dentifrice, twice-daily fluoride dentifrice and once-daily fluoride mouthrinse, and thrice-daily fluoride dentifrice. At the end of each treatment period, samples of unstimulated saliva and dental biofilm were collected 8 h after the last oral hygiene procedure. Fluoride concentrations in saliva and dental biofilm were analyzed using a specific electrode. The fluoride concentrations in saliva and dental biofilm 8 h after the last use of fluoride products did not differ among treatments. The results of this study suggest that treatments with home-use fluoride products have no long-term effect on fluoride concentrations in saliva and in dental biofilm of residents of an area with a fluoridated water supply.

  7. Discovery of Interstellar Hydrogen Fluoride

    CERN Document Server

    Neufeld, D A; Schilke, P; Phillips, T G; Neufeld, David A.; Zmuidzinas, Jonas; Schilke, Peter; Phillips, Thomas G.

    1997-01-01

    We report the first detection of interstellar hydrogen fluoride. Using the Long Wavelength Spectrometer (LWS) of the Infrared Space Observatory (ISO), we have detected the 121.6973 micron J = 2 - 1 line of HF in absorption toward the far-infrared continuum source Sagittarius B2. The detection is statistically significant at the 13 sigma level. On the basis of our model for the excitation of HF in Sgr B2, the observed line equivalent width of 1.0 nm implies a hydrogen fluoride abundance of 3E-10 relative to H2. If the elemental abundance of fluorine in Sgr B2 is the same as that in the solar system, then HF accounts for ~ 2% of the total number of fluorine nuclei. We expect hydrogen fluoride to be the dominant reservoir of gas-phase fluorine in Sgr B2, because it is formed rapidly in exothermic reactions of atomic fluorine with either water or molecular hydrogen; thus the measured HF abundance suggests a substantial depletion of fluorine onto dust grains. Similar conclusions regarding depletion have previously...

  8. Removal of fluoride in aqueous solution by adsorption on acid activated water treatment sludge

    Science.gov (United States)

    Vinitnantharat, Soydoa; Kositchaiyong, Sriwilai; Chiarakorn, Siriluk

    2010-06-01

    This paper reports the use of a pellet of adsorbent made from water treatment sludge (S) and acid activated water treatment sludge (SH) for removal of fluoride in the batch equilibration technique. The influence of pH, adsorbent dosage, temperature and effect of other ions were employed to find out the feasibility of acid activated adsorbent to remove fluoride to the permissible concentration of 0.7 mg/L. The results from the adsorption isotherm followed both Langmuir and Freundlich models and the highest fluoride removal was found for adsorbent activated with acetic acid at 2.0 mol/L. The optimum adsorbent dosage was found at 40 g/L, 0.01 mol/L acid activated adsorbent which was able to adsorb fluoride from 10 down to 0.11 mg/L. The adsorption capacity was decreased when the temperature increased. This revealed that the adsorption of fluoride on SH was exothermic. In the presence of nitrate and carbonate ions in the aqueous solution, fluoride removal efficiency of SH decreased from 94.4% to 86.6% and 90.8%, respectively. However, there is no significant effect in the presence of sulfate and chloride ions.

  9. Development of a nanosphere adsorbent for the removal of fluoride from water.

    Science.gov (United States)

    Zhang, Kaisheng; Wu, Shibiao; He, Junyong; Chen, Liang; Cai, Xingguo; Chen, Kai; Li, Yulian; Sun, Bai; Lin, Dongyue; Liu, Guqing; Kong, Lingtao; Liu, Jinhuai

    2016-08-01

    A new uniform-sized CeCO3OH nanosphere adsorbent was developed, and tested to establish its efficiency, using kinetic and thermodynamic studies, for fluoride removal. The results demonstrated that the CeCO3OH nanospheres exhibited much high adsorption capacities for fluoride anions due to electrostatic interactions and exchange of the carbonate and hydroxyl groups on the adsorbent surface with fluoride anions. Adsorption kinetics was fitted well by the pseudo-second-order model as compared to a pseudo-first-order rate expression, and adsorption isotherm data were well described by Langmuir model with max adsorption capacity of 45mg/g at pH 7.0. Thermodynamic examination demonstrated that fluoride adsorption on the CeCO3OH nanospheres was reasonably endothermic and spontaneous. Moreover, the CeCO3OH nanospheres have less influence on adsorption of F(-) by pH and co-exiting ions, such as SO4(2-), Cl(-), HCO3(-), CO3(2-), NO3(-) and PO4(3-), and the adsorption efficiency is very high at the low initial fluoride concentrations in the basis of the equilibrium adsorption capacities. This study indicated that the CeCO3OH nanospheres could be developed into a very viable technology for highly effective removal of fluoride from drinking water. PMID:27138842

  10. Ruthenium olefin metathesis catalysts containing fluoride

    OpenAIRE

    Guidone, Stefano; Songis, Olivier; Falivene, Laura; Nahra, Fady; Slawin, Alexandra Martha Zoya; Jacobsen, Heiko; Cavallo, Luigi; Cazin, Catherine S. J.

    2015-01-01

    The authors gratefully acknowledge the EC through the 7th framework program (grant CP-FP 211468-2 EUMET), the Royal Society (University Research Fellowship to CSJC) for financial support. The reaction of the ruthenium complex cis-Caz-1 with silver fluoride affords the first example of an active olefin metathesis pre-catalyst containing fluoride ligands. The cis geometry of the precursor complex is key to the successful fluoride exchange reaction. Computational studies highlight the stabili...

  11. Fluoride Importance in Controlling Caries and Fluorosis

    OpenAIRE

    Gaurav Solanki

    2012-01-01

    The use of fluorides for oral health has always involved a balance between the protective benefit against dental caries and the risk of developing fluorosis. The link between fluoride and dental health was established to determining the causes of dental fluorosis or enamel mottling. Fluorosis in Indian children was highly prevalent in the early 1990s. Policy were introduced to control fluoride exposure and to reduce the prevalence of fluorosis. The study aimed of describing the prevalence, se...

  12. FLUORIDATION CHEMISTRY: EQUILIBRIA AND KINETICS OF FLUORIDE AND FLUORO-COMPLEXES

    Science.gov (United States)

    The most common fluoridating agents used by major American waterworks are hexafluorosilicic acid (H2SiF6) and sodium hexxafluorosilicate (Na2SiF6). According to the 1992 Water Fluoridation Census where 10,002 utilities responded affirmatively to fluoridating their water, 59% ...

  13. Effect of titanium tetrafluoride, amine fluoride and fluoride varnish on enamel erosion in vitro

    NARCIS (Netherlands)

    Vieira, A; Ruben, JL; Huysmans, MCDNJM

    2005-01-01

    This study aimed at evaluating the effect of 1 and 4% titanium tetrafluoride (TiF4) gels, amine fluoride (AmF) 1 and 0.25% and a fluoride varnish (FP) on the prevention of dental erosion. Two experimental groups served as controls, one with no pretreatment and another one pre-treated with a fluoride

  14. PRECIPITATION OF URANIUM PEROXIDE OF LOW FLUORIDE CONTENT FROM SOLUTIONS CONTAINING FLUORIDES

    Science.gov (United States)

    King, E.J.; Clark, H.M.

    1958-08-12

    S>A method is described for the preparation of fluoride free uraniunn peroxide precipitates, even though the solution from which the precipitation is made is contaminated with fluorides. This is accomplished by add ing aluminum ions to the solution, where they complex any fluoride present and prevent its precipitation with the uramum peroxide.

  15. High fluoride exposure in hemodialysis patients.

    Science.gov (United States)

    Bello, V A; Gitelman, H J

    1990-04-01

    The observation of higher plasma flouride levels in our hemodialysis (HD) patients than our continuous ambulatory peritoneal dialysis (CAPD) patients (4.0 +/- 0.5 mumol/L [n = 17] v 2.5 +/- 0.3 mumol/L [n = 17], P less than 0.005) prompted an evaluation of fluoride metabolism during HD. We found that serum fluoride was completely ultrafiltrable across cuprophane membranes (99% +/- 4%) and that HD produced acute changes in plasma fluoride levels that correlated well with the fluoride gradient between plasma and dialysis fluid at the start of dialysis. Our HD fluids contained significantly higher fluoride concentrations than were present in commercially prepared peritoneal dialysis fluid. Our fluids are prepared from fluoridated tap water that is purified by reverse osmosis (RO). We conclude that the different concentrations of fluoride in our dialysis fluids account for the differences in the plasma flouride concentrations between our dialysis groups. Since many HD units rely on RO systems to purify fluoridated tap water, it is likely that many HD patients are being exposed inadvertently to increased concentrations of fluoride.

  16. Apatite precipitation on a novel fast-setting calcium silicate cement containing fluoride

    Science.gov (United States)

    Ranjkesh, Bahram; Chevallier, Jacques; Salehi, Hamideh; Cuisinier, Frédéric; Isidor, Flemming; Løvschall, Henrik

    2016-01-01

    Abstract Aim: Calcium silicate cements are widely used in endodontics. Novel fast-setting calcium silicate cement with fluoride (Protooth) has been developed for potential applications in teeth crowns including cavity lining and cementation. Objective: To evaluate the surface apatite-forming ability of Protooth compositions as a function of fluoride content and immersion time in phosphate-buffered saline (PBS). Material and methods: Three cement compositions were tested: Protooth (3.5% fluoride and 10% radiocontrast), ultrafast Protooth (3.5% fluoride and 20% radiocontrast), and high fluoride Protooth (15% fluoride and 25% radiocontrast). Powders were cap-mixed with liquid, filled to the molds and immersed in PBS. Scanning electron microscopy, energy dispersive X-ray analysis, and Raman spectroscopy were used to characterize the precipitations morphology and composition after 1, 7, 28, and 56 days. Apatite/belite Raman peak height indicated the apatite thickness. Results: Spherical calcium phosphate precipitations with acicular crystallites were formed after 1-day immersion in PBS and Raman spectra disclosed the phosphate band at 965 cm−1, supporting the apatite formation over Protooth compositions. The apatite deposition continued and more voluminous precipitations were observed after 56 days over the surface of all cements. Raman bands suggested the formation of β-type carbonated apatite over Protooth compositions. High fluoride Protooth showed the most compact deposition with significantly higher apatite/belite ratio compared to Protooth and ultrafast Protooth after 28 and 56 days. Conclusions: Calcium phosphate precipitations (apatite) were formed over Protooth compositions after immersion in PBS with increasing apatite formation as a function of time. High fluoride Protooth exhibited thicker apatite deposition. PMID:27335901

  17. Fluoride in cerebrospinal fluid of patients with fluorosis.

    OpenAIRE

    Hu, Y H; Wu, S S

    1988-01-01

    The CSF fluoride level of individuals drinking water with normal fluoride content and of patients with endemic fluorosis were studied. For the purpose of studying the relationship between the dynamic equilibrium of the CSF fluoride and other body fluids, urine and blood fluoride were examined simultaneously. Fluoride was revealed in every CSF sample of the control group and its mean value was lower than that of the blood. The CSF fluoride concentration of patients with fluorosis was slightly ...

  18. 76 FR 2383 - Proposed HHS Recommendation for Fluoride Concentration in Drinking Water for Prevention of Dental...

    Science.gov (United States)

    2011-01-13

    ... that provide fluoride now include mouthrinses, fluoride supplements, and professionally applied... fluoride toothpaste (if swallowed) and fluoride supplements, have become available. Fluoride intake from... pharyngeal cancers, and sports-related craniofacial injuries: a report on recommendations of the Task...

  19. Urinary fluoride output in children following the use of a dual-fluoride varnish formulation

    Directory of Open Access Journals (Sweden)

    Kelly Polido Kaneshiro Olympio

    2009-06-01

    Full Text Available OBJECTIVE: This study evaluated the bioavailability of fluoride after topical application of a dual-fluoride varnish commercially available in Brazil, when compared to DuraphatTM. MATERIAL AND METHODS: The urinary fluoride output was evaluated in seven 5-year-old children after application of the fluoride varnishes, in two different phases. In the first phase (I, children received topical application of the fluoride varnish Duofluorid XII (2.92% fluorine, calcium fluoride + 2.71% fluorine, sodium fluoride, FGM TM. After 1-month interval (phase II, the same amount (0.2 mL of the fluoride varnish Duraphat (2.26% fluorine, sodium fluoride, ColgateTM was applied. Before each application all the volunteers brushed their teeth with placebo dentifrice for 7 days. Urinary collections were carried out 24 h prior up to 48 h after the applications. Fluoride intake from the diet was also estimated. Fluoride concentration in diet samples and urine was analyzed with the fluoride ion-specific electrode and a miniature calomel reference electrode coupled to a potentiometer. Data were tested by ANOVA and Tukey's post hoc test (p<0.05. RESULTS: There were significant differences in the urinary fluoride output between phases I and II. The use of Duofluorid XII did not significantly increase the urinary fluoride output, when compared to baseline levels. The application of Duraphat caused a transitory increase in the urinary fluoride output, returning to baseline levels 48 h after its use. CONCLUSIONS: The tested varnish formulation, which has been shown to be effective in in vitro studies, also can be considered safe.

  20. Factors affecting fluoride and natural organic matter (NOM) removal from natural waters in Tanzania by nanofiltration/reverse osmosis.

    Science.gov (United States)

    Shen, Junjie; Schäfer, Andrea I

    2015-09-15

    This study examined the feasibility of nanofiltration (NF) and reverse osmosis (RO) in treating challenging natural tropical waters containing high fluoride and natural organic matter (NOM). A total of 166 water samples were collected from 120 sources within northern Tanzania over a period of 16 months. Chemical analysis showed that 81% of the samples have fluoride levels exceeding the WHO drinking guideline of 1.5mg/L. The highest fluoride levels were detected in waters characterized by high ionic strength, high inorganic carbon and on some occasions high total organic carbon (TOC) concentrations. Bench-scale experiments with 22 representative waters (selected based on fluoride concentration, salinity, origin and in some instances organic matter) and 6 NF/RO membranes revealed that ionic strength and recovery affected fluoride retention and permeate flux. This is predominantly due to osmotic pressure and hence the variation of diffusion/convection contributes to fluoride transport. Different membranes had distinct fluoride removal capacities, showing different raw water concentration treatability limits regarding the WHO guideline compliance. BW30, BW30-LE and NF90 membranes had a feed concentration limit of 30-40 mg/L at 50% recovery. NOM retention was independent of water matrices but is governed predominantly by size exclusion. NOM was observed to have a positive impact on fluoride removal. Several mechanisms could contribute but further studies are required before a conclusion could be drawn. In summary, NF/RO membranes were proved to remove both fluoride and NOM reliably even from the most challenging Tanzanian waters, increasing the available drinking water sources.

  1. Factors affecting fluoride and natural organic matter (NOM) removal from natural waters in Tanzania by nanofiltration/reverse osmosis.

    Science.gov (United States)

    Shen, Junjie; Schäfer, Andrea I

    2015-09-15

    This study examined the feasibility of nanofiltration (NF) and reverse osmosis (RO) in treating challenging natural tropical waters containing high fluoride and natural organic matter (NOM). A total of 166 water samples were collected from 120 sources within northern Tanzania over a period of 16 months. Chemical analysis showed that 81% of the samples have fluoride levels exceeding the WHO drinking guideline of 1.5mg/L. The highest fluoride levels were detected in waters characterized by high ionic strength, high inorganic carbon and on some occasions high total organic carbon (TOC) concentrations. Bench-scale experiments with 22 representative waters (selected based on fluoride concentration, salinity, origin and in some instances organic matter) and 6 NF/RO membranes revealed that ionic strength and recovery affected fluoride retention and permeate flux. This is predominantly due to osmotic pressure and hence the variation of diffusion/convection contributes to fluoride transport. Different membranes had distinct fluoride removal capacities, showing different raw water concentration treatability limits regarding the WHO guideline compliance. BW30, BW30-LE and NF90 membranes had a feed concentration limit of 30-40 mg/L at 50% recovery. NOM retention was independent of water matrices but is governed predominantly by size exclusion. NOM was observed to have a positive impact on fluoride removal. Several mechanisms could contribute but further studies are required before a conclusion could be drawn. In summary, NF/RO membranes were proved to remove both fluoride and NOM reliably even from the most challenging Tanzanian waters, increasing the available drinking water sources. PMID:26005995

  2. Fabrication and characterization of fluoridated hydroxyapatite nanopowders via mechanical alloying

    Energy Technology Data Exchange (ETDEWEB)

    Fathi, M.H. [Department of Materials Engineering, Isfahan University of Technology, Isfahan, 8415683111 (Iran, Islamic Republic of); Zahrani, E. Mohammadi [Department of Materials Engineering, Isfahan University of Technology, Isfahan, 8415683111 (Iran, Islamic Republic of)], E-mail: emohamadizahrani@gmail.com

    2009-05-05

    The aim of this work was preparation and characterization of fluoridated hydroxyapatite (FHA) nanopowders with different degrees of fluoridation via mechanical alloying (MA) method. FHA nanopowders with a chemical composition of Ca{sub 10}(PO{sub 4}){sub 6}OH{sub 2-x}F{sub x} (where x values were selected equal to 0.0, 0.5, 1.0, 1.5, and 2.0) were synthesized using a mixture of appropriate amounts of calcium hydroxide, phosphorous pentoxide, and calcium fluoride powders by 6 h of mechanical alloying at 300 rpm, using eight balls with a diameter of 20 mm, and the ball-to-powder weight ratio equal to 35:1. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, and ICP-OES analysis techniques were utilized in order to evaluate phase composition, agglomerates size distribution, morphology and particle size, functional groups, and purity of synthesized FHA nanopowders. The FTIR result combined with the X-ray diffraction indicated that single phase of homogeneous FHA with the carbonate peaks in the FTIR spectrum could be prepared after 6 h MA. TEM photomicrograph revealed that obtained powder after 6 h of MA was composed of FHA nanoparticles (35-65 nm). The results of ICP-OES analysis illustrated that synthesized nanopowder could fulfill the requirement of ASTM F1185-88 to be used as a biomaterial.

  3. HOUSEHOLD PURIFICATION OF FLUORIDE CONTAMINATED MAGADI (TRONA)

    DEFF Research Database (Denmark)

    Nielsen, Joan Maj; Dahi, Elian

    1997-01-01

    Purification of fluoride contaminated magadi is studied using bone char sorption and calcium precipitation. The bone char treatment is found to be workable both in columns and in batches where the magadi is dissolved in water prior to treatment. The concentrations in the solutions were 89 g magadi...... treatment method. A procedure for purification of fluoride contaminated magadi at household level is described....

  4. Wide pH range for fluoride removal from water by MHS-MgO/MgCO₃ adsorbent: kinetic, thermodynamic and mechanism studies.

    Science.gov (United States)

    Zhang, Kaisheng; Wu, Shibiao; Wang, Xuelong; He, Junyong; Sun, Bai; Jia, Yong; Luo, Tao; Meng, Fanli; Jin, Zhen; Lin, Dongyue; Shen, Wei; Kong, Lingtao; Liu, Jinhuai

    2015-05-15

    A novel environment friendly adsorbent, micro-nano hierarchical structured flower-like MgO/MgCO3 (MHS-MgO/MgCO3), was developed for fluoride removal from water. The adsorbent was characterized and its defluoridation properties were investigated. Adsorption kinetics fitted well the pseudo-second-order model. Kinetic data revealed that the fluoride adsorption was rapid, more than 83-90% of fluoride could be removed within 30 min, and the adsorption equilibrium was achieved in the following 4 h. The fluoride adsorption isotherm was well described by Freundlich model. The maximum adsorption capacity was about 300 mg/g at pH=7. Moreover, this adsorbent possessed a very wide available pH range of 5-11, and the fluoride removal efficiencies even reached up to 86.2%, 83.2% and 76.5% at pH=11 for initial fluoride concentrations of 10, 20 and 30 mg/L, respectively. The effects of co-existing anions indicated that the anions had less effect on adsorption of fluoride except phosphate. In addition, the adsorption mechanism analysis revealed that the wide available pH range toward fluoride was mainly resulted from the exchange of the carbonate and hydroxyl groups on the surface of the MHS-MgO/MgCO3 with fluoride anions. PMID:25668780

  5. A comparative assessment of fluoride concentration available in saliva using daily prescribed topical fluoride agents

    Science.gov (United States)

    Talwar, Manjit; Tewari, Amrit; Chawla, H. S.; Sachdev, Vinod

    2016-01-01

    Objective: To assess the availability of fluoride concentration in saliva following the use of fluoride mouthrinse and dentifrice. Materials and Methods: The experiment was carried out in 7–15 year-old school children of Chandigarh (n = 90). The children were nonfluoride users. Baseline saliva samples were collected. The subjects were exposed to two test agents, i.e., fluoride mouthrinse (0.05%, 225 ppm F) and dentifrice (1000 ppm F) for 7 days and on the day 8, saliva samples were collected over a 20 hrs period. Wash out period of 31/2 months was there before the subjects were exposed to the second test agent. Fluoride in saliva was estimated using fluoride ion-specific electrode. Written informed consent was taken. Statistical Analysis: Kolmogorov–Smirnov test was applied to test the normality of the variables. Mann–Whitney U-test was used to compare the fluoride concentration available in saliva at respective time intervals subsequent to use of the two test agents. Results: Fluoride concentration was elevated in saliva compared to baseline for both the test agents. Fluoride mouthrinse (0.05% sodium fluoride [NaF]) and dentifrice (1000 ppm monofluorophosphate [MFP]) showed a biphasic clearance. Peak in saliva occurred at 15 mins postuse. Night-time use resulted in higher concentration of fluoride in saliva compared to baseline. There was statistically significantly higher fluoride concentration available in saliva for the dentifrice at 5 hrs, 10 hrs, and 20 hrs postuse (P fluoride concentration in saliva remained elevated to a level of 0.12 ppm for mouthrinse and 0.14 ppm for dentifrice compared to baseline (0.03 ppm) up to 20 hrs postuse. The therapeutic window though not yet established but suggested is 0.1–1 ppm for prevention of demineralization, indicating that daily use of fluoride mouthrinse and dentifrice provides fluoride concentration in saliva for the prevention of demineralization. PMID:27433050

  6. Determination of fluoride content in drinking water and tea infusions using fluoride ion selective electrode

    Directory of Open Access Journals (Sweden)

    Rajković Miloš B.

    2007-01-01

    Full Text Available Potentiometric analysis of fluoride content (as F- ion in solutions by using fluoride ion-selective electrode is simple, reliable and cheap. Very small concentrations of fluoride-ions (to 10-6 mol/dm3 can be determined by fluoride selective electrode, with regulation of ion strength of a solution and control of concentration of hydroxide ions and interfering ions of metals. The influence of pH and complexing ions of metals can be successfully regulated by the TISAB solution and by preserving pH value in the range from 5.00 to 7.00. The content of fluorides in the samples can be determined by the method of direct potentiometer, and in the case of very low concentration by standard addition method. In this paper it was analyzed the determination of fluoride ions concentration in bottled mineral waters and water from Belgrade plumbing in two Belgrade districts (Palilula and Novi Beograd and in tea, by using the fluoride selective electrode. It was determined that the content of fluoride ions in bottled mineral water significantly differs from values given on declaration, and that content of fluoride ions varies over a period of time. The content of fluoride ions in water from plumbing in two Belgrade districts at the time of analysis was significantly increased and exceeded values given in Regulation for drinking water quality. The received results from the analysis of fluorides in teas show that fluorides exist in teas in different concentrations. There are also differences between the same kinds of tea, which is noted with mint (Mentha piperitae folium, as a consequence of differences between soils where it was planted. As taking of fluorides, according to World Health Organisation recommendation (WHO, is limited in the range from 2 to 4 mg per day, it is necessary to give the content of fluorides on all products that are used in human consumption.

  7. Morphology of Polyvinylidene Fluoride Based Gel Polymer Electrolytes

    Institute of Scientific and Technical Information of China (English)

    田立颖; 黄小彬; 唐小真

    2004-01-01

    Two series of polyvinylidene fluoride (PVDF) based gel polymer electrolytes, with different LiClO4 or propylene carbonate (PC) content, were prepared and analyzed by infrared spectrometer, differential scanning calorimetry, scanning electron microscope and complex impedance spectrometer. The results show that there are great interactions between PVDF, PC and lithium cations. Both LiClO4 and PC content lead to evident change of the morphology of the gel polymer electrolytes. The content of LiClO4 and PC also influences the ionic conductivity of the samples,and an ionic conductivity of above 10-3S·cm-1 can be reached at room temperature.

  8. Manufacture and properties of fluoride cement

    Science.gov (United States)

    Malata-Chirwa, Charles David

    This research work aimed at characterising composition, hydration and physical properties of fluoride cement, by studying samples of the cement obtained from Malawi, and comparing them to ordinary Portland cement. By confirming the suitable characteristics of fluoride cement through this work, the results of the research work provide a good basis for the wider adoption of fluoride cement as an alternative to ordinary Portland cement, especially in developing economies. Numerous accounts have been cited regarding the production and use of fluoride cement. Since there have not been conclusive agreement as to its properties, this study was limited to the theories of successful incorporation of fluoride compounds in the manufacture of fluoride cement. Hence, the properties and characteristics reported in this study relate to the cement currently manufactured in Malawi, and, on a comparative basis only, to that manufactured in other parts of the world. Samples of the fluoride cement used in the study were obtained by synthetic manufacture of the cement using common raw materials for the manufacture of fluoride cement that is limestone, silica sand, and fluorspar. These samples were subjected to several comparative tests used to characterise cements including examination under x-ray diffractometer, scanning electron microscopy and tests for setting time and compressive strength. Under similar laboratory conditions, it was possible to prove that fluoride cement hardens more rapidly than ordinary Portland cement. Also observed during the experimental work is that fluoride cement develops higher compressive strengths than ordinary Portland cement. The hardening and setting times are significantly different between the two cements. Also the nature of the hydration products, that is the microstructural development is significantly different in the two cements. The differences brought about between the two cements are because of the presence of fluorine during the clinkering

  9. Diethylenetriaminium hexafluoridotitanate(IV fluoride

    Directory of Open Access Journals (Sweden)

    J. Lhoste

    2008-11-01

    Full Text Available The title compound, (C6H21N4[TiF6]F, was synthesized by the reaction of TiO2, tris(2-aminoethylamine, HF and ethanol at 463 K in a microwave oven. The crystal structure consists of two crystallographically independent [TiF6]2− anions, two fluoride anions and two triply-protonated tris(2-aminoethylamine cations. The Ti atoms are coordinated by six F atoms within slightly distorted octahedra. The anions and cations are connected by intermolecular N—H...F hydrogen bonds.

  10. Method of treating fluoride contaminated wastes

    Energy Technology Data Exchange (ETDEWEB)

    Davis, P.K.; Kakaria, V.K.

    1988-04-05

    A method for treating spent aluminum smelting potliner material containing fluoride contaminants is described which comprises: adding silica to the material to form a mixture thereof; elevating the temperature of the mixture within the range of 1,000/sup 0/ to 1,700/sup 0/C. to form a slag; providing sufficient silica in the mixture and forming the slag in the presence of sufficient water for pyrohydrolysis conditions resulting in the volatilization of substantially all of the fluoride contaminants mostly in the form of hydrogen fluoride; and cooling the slag remaining after volatilizatiion of substantially all of the fluoride contaminants to produce an insoluble silicate glass-residue containing any remaining portion of the fluoride contaminants in an immobile state.

  11. 21 CFR 175.270 - Poly(vinyl fluoride) resins.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Poly(vinyl fluoride) resins. 175.270 Section 175... Substances for Use as Components of Coatings § 175.270 Poly(vinyl fluoride) resins. Poly(vinyl fluoride... the purpose of this section, poly(vinyl fluoride) resins consist of basic resins produced by...

  12. Fluoride Programs in the School Setting: Preventive Dental Health.

    Science.gov (United States)

    Rebich, Theodore, Jr.; And Others

    1982-01-01

    Two types of school-based programs that increase students' use of fluoride for preventive dental health are described. In fluoride mouthrinse programs, teachers give their students a fluoride solution once a week in a paper cup. In areas where the level of fluoride in the water supply is insufficient, the flouride tablet program is used. (JN)

  13. Fluoridation and Defluoridation. Training Module 2.230.2.77.

    Science.gov (United States)

    McMullen, L. D.

    This document is an instructional module package prepared in objective form for use by an instructor familiar with fluoridation and fluoride feeding equipment. Enclosed are objectives, an instructor guide, student handouts and transparency masters. The module considers the principles and purposes of fluoridation, methods of feeding fluoride,…

  14. The Contrasting Character of Early and Late Transition Metal Fluorides as Hydrogen Bond Acceptors.

    Science.gov (United States)

    Smith, Dan A; Beweries, Torsten; Blasius, Clemens; Jasim, Naseralla; Nazir, Ruqia; Nazir, Sadia; Robertson, Craig C; Whitwood, Adrian C; Hunter, Christopher A; Brammer, Lee; Perutz, Robin N

    2015-09-16

    The association constants and enthalpies for the binding of hydrogen bond donors to group 10 transition metal complexes featuring a single fluoride ligand (trans-[Ni(F)(2-C5NF4)(PR3)2], R = Et 1a, Cy 1b, trans-[Pd(F)(4-C5NF4)(PCy3)2] 2, trans-[Pt(F){2-C5NF2H(CF3)}(PCy3)2] 3 and of group 4 difluorides (Cp2MF2, M = Ti 4a, Zr 5a, Hf 6a; Cp*2MF2, M = Ti 4b, Zr 5b, Hf 6b) are reported. These measurements allow placement of these fluoride ligands on the scales of organic H-bond acceptor strength. The H-bond acceptor capability β (Hunter scale) for the group 10 metal fluorides is far greater (1a 12.1, 1b 9.7, 2 11.6, 3 11.0) than that for group 4 metal fluorides (4a 5.8, 5a 4.7, 6a 4.7, 4b 6.9, 5b 5.6, 6b 5.4), demonstrating that the group 10 fluorides are comparable to the strongest organic H-bond acceptors, such as Me3NO, whereas group 4 fluorides fall in the same range as N-bases aniline through pyridine. Additionally, the measurement of the binding enthalpy of 4-fluorophenol to 1a in carbon tetrachloride (-23.5 ± 0.3 kJ mol(-1)) interlocks our study with Laurence's scale of H-bond basicity of organic molecules. The much greater polarity of group 10 metal fluorides than that of the group 4 metal fluorides is consistent with the importance of pπ-dπ bonding in the latter. The polarity of the group 10 metal fluorides indicates their potential as building blocks for hydrogen-bonded assemblies. The synthesis of trans-[Ni(F){2-C5NF3(NH2)}(PEt3)2], which exhibits an extended chain structure assembled by hydrogen bonds between the amine and metal-fluoride groups, confirms this hypothesis.

  15. Effects of Saliva and Topical Fluoride Application on Enamel of Young Permanent Teeth Demineralized by Carbonated Beverage%唾液及氟化物对碳酸饮料导致年轻恒牙釉质脱矿的影响

    Institute of Scientific and Technical Information of China (English)

    周娟; 许明莲; 杜姗姗; 胡孝丽; 罗志晓; 柴红波; 朱友家

    2013-01-01

    Objective To explore the remineralization of young permanent teeth demineralized by carbonated beverage with human saliva and topical fluoride application. Methods Thirty young permanent premolar were collected from orthodontic extraction and immersed in carbonated beverage for one week,then they were randomly divided into group A,B and C(n = 10). All teeth were cleaned with distilled water,and then put into normal human saliva,0.1% NaF solution and toothpaste with fluoride for one month,respectively. The morphology changes of enamel surface were observed by scanning electron microscope, and the results was analyzed. Results The enamel surface of group A showed uneven distribution of the mineral particle,which was cloudy covering in the lacunae making the aperture smaller and the depth shallower;the enamel surface of group B showed discrete and irregular settlings with piece or mass form covering in the lacunae, making the depth shallower; the enamel surface of group C showed flat,the depth of demineralization area was superficial,there was some compact and irregular settlings, the degree of demineralization of axon cylinder was obviously reduced, and the density of good mineralization position was close to normal enamel. Conclusion After demineralizing young permanent teeth with carbonated beverage, the remineralization could occur in oral environment within limited degree. The application of fluoride in enamel surface can promote the remineralization.%目的:探讨碳酸饮料处理过的年轻恒牙分别在正常人体唾液中,和经氟化物处理后,牙釉质的再矿化情况.方法:收集因正畸减数拔除的年轻恒前磨牙30颗,置入碳酸饮料中浸泡1周后,将其随机分为3组,用蒸馏水洗净后,分别置入正常人体唾液(A组)、0.1% NaF溶液(B组)及含氟牙膏(C组)中1个月,应用扫描电镜观察各组牙齿牙釉质表面的形态学变化,并对影像结果进行对比分析.结果:A组牙齿的釉质表面有分布不

  16. The effect of bicarbonate/fluoride dentifrices on human plaque pH.

    Science.gov (United States)

    Blake-Haskins, J C; Gaffar, A; Volpe, A R; Bánóczy, J; Gintner, Z; Dombi, C

    1997-01-01

    The acidogenic response in dental plaque after rinsing with sodium bicarbonate/fluoride dentifrice slurries was studied using three intra-oral models. In the first model, resting plaque pH was monitored in mesiobuccal plaque on upper molars and premolars in six healthy subjects after abstinence from normal oral hygiene for three days. These measurements were followed by a three-minute rinse with 10% sucrose and, following a two-minute interval, a three-minute rinse with a test dentifrice slurry. After the test dentifrice rinse, pH was monitored at regular intervals up to 60 minutes. Flow rate, pH and buffer capacity of stimulated saliva were also determined. Changes in resting pH, plaque pH minima, and maximum pH drop were calculated. A clear elevation in the resting pH was observed after bicarbonate/fluoride dentifrice rinses, and a significant increase was obtained in the pH minima. The smallest pH drop also was found after treatment with the bicarbonate/fluoride dentifrice rinse treatment (p antimony pH electrodes was used to study the effects of rinsing with increasing concentrations of sodium bicarbonate and calcium carbonate solutions, and with a fluoride dentifrice containing sodium bicarbonate. The response to these treatments was found to be rapid, dose-dependent, and was the greatest from the sodium bicarbonate. A third model used 24 subjects to assess the effects of sodium bicarbonate/fluoride dentifrice on plaque pH before and after a glucose challenge. The use of the bicarbonate/fluoride dentifrice resulted in significantly less measurable plaque acid than the fluoride dentifrice treatment. Collectively, these results indicate bicarbonate in dentifrice to be an effective buffering agent for stabilizing the pH and neutralizing plaque acids in dental plaque. PMID:9586535

  17. Evaluation of toxic action of fluorides on agricultural plants

    Directory of Open Access Journals (Sweden)

    V. N. Grishko

    2007-03-01

    Full Text Available The toxicity of potassium fluoride, sodium fluoride and ammonium fluoride for pea, maize, oat and onion was studied. It was found that the level of the toxic influence had grown with increase of fluoride concentration in the media of growth (from 5 to 100 mg of F–/l. By increase of the toxic influence the agricultural crops are disposed in the following row: oat < onion < maize < pea. Ammonium fluoride demonstrates lesser toxicity, than potassium and sodium fluorides. Under low concentrations of fluoride compounds (5 and 10 mg of F–/l stimulation of roots growth is noted only for the oat.

  18. Metabolism of ammonium fluoride and sodium monofluoroacetate by experimental Acacia georginae

    Energy Technology Data Exchange (ETDEWEB)

    Hall, R.J.

    1974-01-01

    Plants of Acacia georginae (one of numerous toxic tropical species now known to contain monofluoroacetate) were cultivated in nutrient-washed quartz, and in soil. Attempts were made to induce the formation of organic fluorine by treatment of the roots with a solution of ammonium fluoride. Only small amounts of carbon-fluorine material were measured in the leaves and roots, and examinations by physico-chemical methods failed to detect any evidence of the presence of monofluoroacetate in any of the plants. Similar plants were treated with sodium monofluoroacetate which underwent considerable degradation to an acid-labile form of fluorine (probably inorganic fluoride). The results of the analyses of the roots and leaves for fluorine revealed that the difference between acid-labile (diffusible) fluoride and total fluorine cannot be taken as a measure of the organic fluorine.

  19. Physiologic Conditions Affect Toxicity of Ingested Industrial Fluoride

    Directory of Open Access Journals (Sweden)

    Richard Sauerheber

    2013-01-01

    Full Text Available The effects of calcium ion and broad pH ranges on free fluoride ion aqueous concentrations were measured directly and computed theoretically. Solubility calculations indicate that blood fluoride concentrations that occur in lethal poisonings would decrease calcium below prevailing levels. Acute lethal poisoning and also many of the chronic effects of fluoride involve alterations in the chemical activity of calcium by the fluoride ion. Natural calcium fluoride with low solubility and toxicity from ingestion is distinct from fully soluble toxic industrial fluorides. The toxicity of fluoride is determined by environmental conditions and the positive cations present. At a pH typical of gastric juice, fluoride is largely protonated as hydrofluoric acid HF. Industrial fluoride ingested from treated water enters saliva at levels too low to affect dental caries. Blood levels during lifelong consumption can harm heart, bone, brain, and even developing teeth enamel. The widespread policy known as water fluoridation is discussed in light of these findings.

  20. A fluoride release-adsorption-release system applied to fluoride-releasing restorative materials.

    Science.gov (United States)

    Suljak, J P; Hatibovic-Kofman, S

    1996-09-01

    This investigation compared the initial fluoride release and release following refluoridation of three resin-modified glass-ionomer cements (Photac-Fil Applicap, Vitremer, and Fuji II LC) and a new polyacid-modified resin composite material (Dyract). After daily flouride release was measured for 8 days, specimens were refluoridated in 1,000-ppm solutions of fluoride ion for 10 minutes and fluoride release was measured for 5 days. Two further 5-day refluoridation-release periods were carried out. All materials released fluoride initially. Photac released the most; Dyract released the least. Initial release was greatest over the first few days. All materials released significantly more fluoride for 24 to 48 hours after refluoridation. Less fluoride was released with each successive refluoridation for the three glass-ionomer cements. The release from the Dyract compomer remained at a comparatively constant and significantly lower level following each refluoridation.

  1. A study of fluoride groundwater occurrence in Nathenje, Lilongwe, Malawi

    Science.gov (United States)

    Msonda, K. W. M.; Masamba, W. R. L.; Fabiano, E.

    A study was carried out to determine fluoride concentration in groundwaters of Nathenje area situated in Lilongwe District in the central region of Malawi. Water samples were collected from 176 boreholes and shallow wells during different months in 2001 and 2002. Samples were then analysed for fluoride by using a fluoride electrode and an ion selective meter. The results showed that fluoride concentrations for the rainy season varied from fluorosis in areas where the fluoride concentration was high.

  2. Physiologic Conditions Affect Toxicity of Ingested Industrial Fluoride

    OpenAIRE

    Richard Sauerheber

    2013-01-01

    The effects of calcium ion and broad pH ranges on free fluoride ion aqueous concentrations were measured directly and computed theoretically. Solubility calculations indicate that blood fluoride concentrations that occur in lethal poisonings would decrease calcium below prevailing levels. Acute lethal poisoning and also many of the chronic effects of fluoride involve alterations in the chemical activity of calcium by the fluoride ion. Natural calcium fluoride with low solubility and toxicity ...

  3. Corrosion action and passivation mechanism of magnesium alloy in fluoride solution

    Institute of Scientific and Technical Information of China (English)

    LI Jian-zhong; HUANG Jiu-gui; TIAN Yan-wen; LIU Chang-sheng

    2009-01-01

    Corrosion action and passive mechanism of magnesium alloy in the fluoride solution were studied by means of scanning electron microscopy(SEM), energy dispersive X-ray spectroscopy(EDS), and electrochemistry methods. The results show that an insoluble MgF2 film is generated on the surface of magnesium alloy activated in the hydrofluoric acid. And the mass of the deposited MgF2 film may reach a constant value, when the mass ratio of Mg/F on the magnesium alloy surface is fixed at 11.3-1. The activated magnesium alloy gains a 'passivation state' in a mixture of sulfuric acid and hydrofluoric acid at a volume ratio of less than 1.2. At the same time the mass of magnesium alloy is maintained as a function of the time. When the ratio is above 1.4, the mass of magnesium alloy rapidly decreases. The passive film formed through adsorption of HF2- (or H2F3-, H3F4-) ions by the deposited MgF2 film can protect the magnesium alloy from corrosion in fluoride solution, but not in non-fluoride solutions. The passive state is maintained for activated magnesium alloy in an acidic sulfuric nickel solution with added fluoride. If fluoride and carbonate are added to the acidic sulfuric nickel solution, a replacement reaction between magnesium alloy and solution takes place.

  4. PROCESS FOR TREATING VOLATILE METAL FLUORIDES

    Science.gov (United States)

    Rudge, A.J.; Lowe, A.J.

    1957-10-01

    This patent relates to the purification of uranium hexafluoride, made by reacting the metal or its tetrafluoride with fluorine, from the frequently contained traces of hydrofluoric acid. According to the present process, UF/sub 6/ containing as an impurity a small amount of hydrofluoric acid, is treated to remove such impurity by contact with an anhydrous alkali metal fluoride such as sodium fluoride. In this way a non-volatile complex containing hydrofluoric acid and the alkali metal fluoride is formed, and the volatile UF /sub 6/ may then be removed by distillation.

  5. The effect of fluoride impregnated dental floss on enamel fluoride uptake in vitro and streptococcus mutans colonization in vivo.

    Science.gov (United States)

    Chaet, R; Wei, S H

    1977-01-01

    The conclusions reached from this investigation can be summarized as follows: Fluoride can be incorporated into unwaxed dental floss. Placement of the fluoride impregnated dental floss in acid-buffer solution results in the release of most of the fluoride in the floss. Interproximal surfaces of teeth treated in vitro with fluoride impregnated dental floss acquired significantly (approximately three fold) more enamel fluoride than those treated with plain dental floss. The number of in vivo interproximal areas harboring Streptococcus mutans was reduced significantly after treatment with fluoride impregnated dental floss. Further studies should be done to establish the biological, physiochemical, manufacturing, and practical aspects of fluoride impregnated dental floss.

  6. Thermochemistry of calcium oxide and calcium hydroxide in fluoride slags

    Science.gov (United States)

    Chattopadhyay, S.; Mitchell, A.

    1990-08-01

    Calcium oxide activity in binary CaF2-CaO and ternary CaF2-CaO-Al2O3 and CaF2-CaO-SiO2 slags has been determined by CO2-slag equilibrium experiments at 1400 °C. The carbonate ca-pacity of these slags has also been computed and compared with sulfide capacity data available in the literature. The similarity in trends suggests the possibility of characterizing carbonate capacity as an alternative basicity index for fluoride-base slags. Slag-D2O equilibrium experi-ments are performed at 1400°C with different fluoride-base slags to determine water solubility at two different partial pressures of D2O, employing a new slag sampling technique. A novel isotope tracer detection technique is employed to analyze water in the slags. The water solubility data found show higher values than the previous literature data by an order of magnitude but show a linear relationship with the square root of water vapor partial pressure. The activity of hydroxide computed from the data is shown to be helpful in estimating water solubility in in-dustrial electroslag remelting (ESR) slags.

  7. Dental fluorosis and skeletal fluoride content as biomarkers of excess fluoride exposure in marsupials.

    Science.gov (United States)

    Death, Clare; Coulson, Graeme; Kierdorf, Uwe; Kierdorf, Horst; Morris, William K; Hufschmid, Jasmin

    2015-11-15

    Particulate and gaseous fluoride emissions contaminate vegetation near fluoride-emitting industries, potentially impacting herbivorous wildlife in neighboring areas. Dental fluorosis has been associated with consumption of fluoride-contaminated foliage by juvenile livestock and wildlife in Europe and North America. For the first time, we explored the epidemiology and comparative pathology of dental fluorosis in Australian marsupials residing near an aluminium smelter. Six species (Macropus giganteus, Macropus rufogriseus, Wallabia bicolor, Phascolarctos cinereus, Trichosurus vulpecula, Pseudocheirus peregrinus) demonstrated significantly higher bone fluoride levels in the high (n=161 individuals), compared to the low (n=67 individuals), fluoride areas (pfluorosis in eutherian mammals. Within the high-fluoride area, 67% of individuals across the six species showed dental enamel lesions, compared to 3% in the low-fluoride areas. Molars that erupted before weaning were significantly less likely to display pathological lesions than those developing later, and molars in the posterior portion of the dental arcade were more severely fluorotic than anterior molars in all six species. The severity of dental lesions was positively associated with increasing bone fluoride levels in all species, revealing a potential biomarker of excess fluoride exposure.

  8. The Adsorption of Hydrogen Fluoride and Fluoride Ion on a Water Treatment Sludge

    OpenAIRE

    Oh, Taek-Keun; Saeki, Kazutoshi

    2009-01-01

    The hydrogen fluoride (HF) and fluoride ion (F^-) adsorption potentials of a water treatment sludge were investigated in a batch mode as a function of pH, contact time, initial fluoride concentrations, and other co-existing anions. The maximum removal of total fluoride was apparently observed at pH 5.1, whereas HF or F^- adsorptions showed nearly 100% in pH range from 2.2 to 4.3. The HF or F^- adsorption by the water treatment sludge has occurred rapidly during the initial 5.60 min and therea...

  9. Determination of fluoride content in drinking water and tea infusions using fluoride ion selective electrode

    OpenAIRE

    Rajković Miloš B.; Novaković Ivana D.

    2007-01-01

    Potentiometric analysis of fluoride content (as F- ion) in solutions by using fluoride ion-selective electrode is simple, reliable and cheap. Very small concentrations of fluoride-ions (to 10-6 mol/dm3) can be determined by fluoride selective electrode, with regulation of ion strength of a solution and control of concentration of hydroxide ions and interfering ions of metals. The influence of pH and complexing ions of metals can be successfully regulated by the TISAB solution and by preservin...

  10. Alumina supported carbon composite material with exceptionally high defluoridation property from eggshell waste.

    Science.gov (United States)

    Lunge, Sneha; Thakre, Dilip; Kamble, Sanjay; Labhsetwar, Nitin; Rayalu, Sadhana

    2012-10-30

    A new alumina supported carbon composite material called "Eggshell Composite" (EC) was synthesized from eggshell waste as calcium source for selective fluoride adsorption from water. The effect of various synthesis parameters like eggshell (ES): Eggshell membrane (ESM) ratio, aluminium loading, mixing time and calcinations temperature to optimize the synthesis conditions for selective fluoride removal has been studied. It was observed that the synthesis parameters have significant influence on development of EC and in turn on fluoride removal capacity. EC synthesized was characterized for elemental composition, morphology, functionality and textural properties. Results showed that EC obtained from eggshell modified with alumina precursor is more selective and efficient for fluoride removal. Langmuir and Freundlich isotherm were used to obtain ultimate fluoride removal capacity. The calcium and alumina species in EC shows synergistic effect in fluoride adsorption process. Fluoride sorption studies were carried out in synthetic, groundwater and wastewater. EC proved to be a potential, indigenous and economic adsorbent for fluoride removal.

  11. Contamination of fluoride in groundwater and its effect on human health: a case study in hard rock aquifers of Siddipet, Telangana State, India

    Science.gov (United States)

    Narsimha, A.; Sudarshan, V.

    2016-06-01

    Hydrogeochemical investigation has been carried out in the granitic terrain of Siddipet area, Medak district, Telangana State, India with an aim to understand the distribution of fluoride in the groundwater and to understand the relationship of fluoride with other major ions, and also to identify the high fluoride-bearing groundwater zones. 104 groundwater samples were analyzed in the study area for fluoride and other major ions like calcium, magnesium, chloride, carbonate, bicarbonate, sodium, potassium, sulfate, and nitrate in addition to pH and electrical conductivity. The studies revealed that the concentration of fluoride in groundwater is ranging from 0.2 to 2.2 mg L-1 with a mean of 1.1 mg L-1. Nearly 22 % of groundwater has more than the permissible limit of fluoride (1.5 mg L-1), which is responsible for the endemic dental fluorosis in the area concerned. Geochemical classification of groundwater shows that Na-HCO3, Ca-Cl, and Ca-HCO3-Na are the dominant hydrochemical facies. Gibbs diagram shows rock-water interaction dominance and evaporation dominance, which are responsible for the change in the quality of water in the hard rock aquifer of the study area. The groundwater in villages and its environs are affected by fluoride contamination, and consequently majority of the population living in these villages suffer from dental fluorosis. Hence, they are advised to consume drinking water which has less than 1.5 mg L-1 fluoride to avoid further fluorosis risks.

  12. Efecto de la arginina 8%-carbonato de calcio y del fluoruro de sodio al 5% en la reducción de la hipersensibilidad dentinaria post terapia periodontal: ensayo clínico Effect of 8% arginine, calcium carbonate and 5% sodium fluoride on the reduction of the dentine hipersensitivity post periodontal therapy: clinical trial

    Directory of Open Access Journals (Sweden)

    M Márquez

    2011-04-01

    embargo, se logró una mayor reducción del dolor en aquellos pacientes que utilizaron la terapia de arginina al 8% y carbonato de calcio, con un 60% de los individuos sin dolor y con una mediana final de 0 en comparación al grupo con barniz de flúor al 5% y un dentrífico fluorado que mantuvieron en el 100% de los sujetos algún grado de dolor y presentando una mediana final en la escala VAS de 2.Aim: The aim of this clinical study was to evaluate and to compare the efficacy in reducing the dentine hypersensitivity of an 8% arginine, calcium carbonate, 1.450 ppm sodium monofluorophosphate dentifrice with topical application and twice-daily brushing, with a negative control toothpaste containing calcium carbonate and 1.450 ppm fluoride as MFP, after periodontal treatment (baseline and four weeks respectively. Methods: A four-week clinical study with 20 subjects with diagnosis of slight to moderate chronic periodontitis under mechanical periodontal treatment and presence of gingival recessions in incisors, canines or premolars, stratified based on baseline tooth sensitivity. Subjects brushed with either a 1.450 ppm fluoride dentifrice or a marketed 8% arginine calcium carbonate dentifrice twice daily for approximately one minute. At screening, baseline and weeks four, subjects' tooth sensitivity was determined through both evaporative (Schiff and Visual Analogue Scale [VAS]. The same examiner throughout the study performed subject assessments using each stimulus. Results: Both subject groups exhibited significant reductions from baseline to four weeks in dentine hypersensitivity. However, patients who received 8% arginine calcium carbonate therapy, exhibited a greater reduction, with a 60% of individuals lacking of pain and with a final median of 0 in comparison with the 5% fluoride varnish and fluoride toothpaste group in which a 100% of subjects felt some degree of pain, presenting a final medium VAS scale of 2.

  13. Synthesis of Mg{sub 2}FeH{sub 6} containing as additives transition metal and transition metal fluorides or carbon; Sintese de Mg{sub 2}FeH{sub 6} contando como aditivos metais de transicao e fluoretos de metais de transicao ou carbono

    Energy Technology Data Exchange (ETDEWEB)

    Zepon, G.; Leiva, D.R.; Botta, W.J., E-mail: guizepon@yahoo.com.b [Universidade Federal de Sao Carlos (DEMa/UFSCar), SP (Brazil). Dept. de Engenharia de Materiais

    2010-07-01

    The Mg{sub 2}FeH{sub 6} is a promising way of storing hydrogen in solid form, composed by elements that have low cost and, at the same time, high volumetric storage density: 150 kg H{sub 2}/m{sup 3}. However, this complex hydride is not easily synthesized as a single phase material. The hydrogen sorption high temperature and slow kinetics are the major limitations for the practical application of the Mg{sub 2}FeH{sub 6} as a hydrogen storage material. Little is known about the effects of additives in Mg{sub 2}FeH{sub 6} based nanocomposites in this work were synthesized by MAE under hydrogen atmosphere nanocomposites based on Mg{sub 2}FeH{sub 6} containing additives as transition metals, transition metals fluorides of transition metals or carbon, in order to obtain information on the effects of the selected additives. To this end, we used characterization techniques such as XRD, SEM and TEM, thermal analysis by DSC and curves made in apparatus PCT.(author)

  14. Fluoride release and uptake capacities of fluoride-releasing restorative materials.

    Science.gov (United States)

    Attar, Nuray; Turgut, Melek D

    2003-01-01

    Many fluoride-releasing dental materials are being sold on the basis of their cariostatic properties. However, the amount fluoride release of these materials is still uncertain. This study investigated the fluoride release and uptake characteristics of four flowable resin composites (Heliomolar Flow, Tetric Flow, Wave, Perma Flo), one flowable compomer (Dyract flow), one conventional glass ionomer cement mixed with two different powder/liquid ratios (ChemFlex Syringeable and ChemFlex Condensable), one packable resin composite (SureFil), one ion-releasing composite (Ariston pHc) and one resin-modified glass ionomer cement (Vitremer). Seven discs (6-mm diameter and 1.5-mm height) were prepared for each material. Each disc was immersed in 3.5 ml of deionized water within a plastic vial and stored at 37 degrees C. The deionized water was changed every 24 hours and the release of fluoride was measured for 30 days. At the end of this period, the samples were recharged with 2 ml of 1.23% acidulated phosphate fluoride (APF) gel for four minutes. Then, all samples were reassessed for an additional 10 days. The fluoride release of all samples was measured with a specific fluoride electrode and an ionanalyzer. Statistical analyses were conducted using two-way repeated measure ANOVA and Duncan's multiple range tests. For all tested materials, the greatest fluoride release was observed after the first day of the study (p0.05). Ariston pHc released the highest amount of fluoride, followed by ChemFlex Syringeable, Vitremer and ChemFlex Condensable. There were statistically significant differences among these materials (p<0.05). Fluoride release of all materials were significantly increased after the first day following refluoridation and Ariston pHc released the greatest among all materials (p<0.01). At the end of two days of refluoridation, the fluoride release rate for each material dropped quickly and stabilized within three days.

  15. Fluoride geochemistry of thermal waters in Yellowstone National Park: I. Aqueous fluoride speciation

    Science.gov (United States)

    Deng, Y.; Nordstrom, D.K.; Blaine, McCleskey R.

    2011-01-01

    Thermal water samples from Yellowstone National Park (YNP) have a wide range of pH (1-10), temperature, and high concentrations of fluoride (up to 50mg/l). High fluoride concentrations are found in waters with field pH higher than 6 (except those in Crater Hills) and temperatures higher than 50??C based on data from more than 750 water samples covering most thermal areas in YNP from 1975 to 2008. In this study, more than 140 water samples from YNP collected in 2006-2009 were analyzed for free-fluoride activity by ion-selective electrode (ISE) method as an independent check on the reliability of fluoride speciation calculations. The free to total fluoride concentration ratio ranged from 99% at high pH. The wide range in fluoride activity can be explained by strong complexing with H+ and Al3+ under acidic conditions and lack of complexing under basic conditions. Differences between the free-fluoride activities calculated with the WATEQ4F code and those measured by ISE were within 0.3-30% for more than 90% of samples at or above 10-6 molar, providing corroboration for chemical speciation models for a wide range of pH and chemistry of YNP thermal waters. Calculated speciation results show that free fluoride, F-, and major complexes (HF(aq)0, AlF2+, AlF2+ and AlF30) account for more than 95% of total fluoride. Occasionally, some complex species like AlF4-, FeF2+, FeF2+, MgF+ and BF2(OH)2- may comprise 1-10% when the concentrations of the appropriate components are high. According to the simulation results by PHREEQC and calculated results, the ratio of main fluoride species to total fluoride varies as a function of pH and the concentrations and ratios of F and Al. ?? 2011.

  16. Well Waters Fluoride in Enugu, Nigeria

    Directory of Open Access Journals (Sweden)

    EI Ugwuja

    2012-03-01

    Full Text Available Abnormal fluoride levels in drinking water have been associated with adverse health effects. To determine the fluoride content of well waters in Enugu, southeastern Nigeria, water samples from 50 artisan wells chosen by multistage sampling procedure from the 5 zones of Enugu municipality were analyzed in duplicates for their fluoride content. The zonal mean values were 0.60, 0.70, 0.62, 0.62, and 0.63 mg/L for Abakpa Nike, Achara Layout, Obiagu/ Ogui, Trans Ekulu and Uwani, respectively (p<0.05. The mean value for the whole city was 0.63 mg/L. Although, the mean level of fluoride recorded in this study is currently within safe limits (1.5 mg/L, WHO 2011, it is important to monitor continuously the fluoride content of well waters in the municipality in view of the increasing industrial activities going on in the city and heavy reliance on well water for domestic purposes and the widespread use of consumer products containing fluoride.

  17. Debating Water Fluoridation Before Dr. Strangelove.

    Science.gov (United States)

    Carstairs, Catherine

    2015-08-01

    In the 1930s, scientists learned that small amounts of fluoride naturally occurring in water could protect teeth from decay, and the idea of artificially adding fluoride to public water supplies to achieve the same effect arose. In the 1940s and early 1950s, a number of studies were completed to determine whether fluoride could have harmful effects. The research suggested that the possibility of harm was small. In the early 1950s, Canadian and US medical, dental, and public health bodies all endorsed water fluoridation. I argue in this article that some early concerns about the toxicity of fluoride were put aside as evidence regarding the effectiveness and safety of water fluoridation mounted and as the opposition was taken over by people with little standing in the scientific, medical, and dental communities. The sense of optimism that infused postwar science and the desire of dentists to have a magic bullet that could wipe out tooth decay also affected the scientific debate. PMID:26066938

  18. Analysis of fluoride concentration in solutions prepared at dispensing pharmacies

    Directory of Open Access Journals (Sweden)

    Eduardo Pizzatto

    2011-07-01

    Full Text Available Introduction: Fluoride plays an important role in oral health promotion and is considered important in dental caries prevention both in children and adults. Fluoride is widely used at high-risk conditions of caries, when the use of fluoride-containing mouthwashes is recommended, considering that fluoride itself reduces the risk of dental caries. Objective: To evaluate the fluoride concentration in solutions prepared at different dispensing pharmacies in the city of Curitiba – PR, Brazil. Material and methods: The analysis of fluoride concentration was preformed through Ion Chromatography method (DIONEX. Results: The results obtained through this analysis showed that all solutions presented fluoride concentration above that required in the dentist’s prescription, varying between 5.48% and 24.02% more fluoride, at absolute concentration. Conclusion: This finding highlights the increasing risk of fluoride acute intoxication in cases of accidental ingestion of the solution.

  19. Chemisorption of uranium hexa-fluoride on sodium fluoride pellets

    International Nuclear Information System (INIS)

    This paper comprises kinetics of chemical reaction or rather chemisorption of uranium hexafluoride gas on sodium fluoride pellets. The chemisorption is essentially irreversible at room temperature, while the process reverses at high temperature above 280 deg C. This chemisorption process was experimentally conducted in static condition at room temperature and its kinetics was studied. In the experiments, practically pure UF6 was used and the effects of gas pressure and weight of NaF pellets, were studied. In this heterogenous reaction, in which diffusion through ash layer is followed by chemical reaction, the reaction part is instantaneous and is first order with respect to gas concentration. Since the process of chemisorption is not only pure chemical reaction but also gas diffusion through ash layer, the rate constant depreciates with the percentage loading of UF6 on NaF pellets. The kinetic equation for the above process has been established for a particular size of NaF pellets and pellet porosity. (author)

  20. Daily Fluoride Intake from Iranian Green Tea: Evaluation of Various Flavorings on Fluoride Release

    Science.gov (United States)

    Maleki, Afshin; Daraei, Hiua; Mohammadi, Elham; Zandi, Shiva; Teymouri, Pari; Mahvi, Amir Hossien; Gharibi, Fardin

    2016-01-01

    With increased awareness of the health benefits of the compounds in green tea, especially polyphenols, its consumption is rising. The main purpose of this study is to determine the effect of different additives on the released fluoride into tea liquor and also daily fluoride intake. The concentrations of fluoride, nitrate, sulfate, and chloride were measured in 15 different flavored green teas (Refah-Lahijan). The fluoride and other anion concentrations were measured by ion chromatography method. The data were analyzed with Statistical Package for the Social Sciences version 16.0. The results showed that the minimum and maximum concentrations of fluoride in the green tea infusions were 0.162 mg/L (cinnamon-flavored green tea) and 3.29 mg/L (bagged peach-flavored green tea), respectively. The mean concentration of fluoride in the green tea leaves was 52 mg/kg, and approximately 89% of the fluoride was released from the green tea leaves into the infusions after brewing. The fluoride concentrations varied significantly among the examined green teas (P 0.05). Finally, drinking of the studied green teas cannot make a significant contribution to the daily dietary intake of F for consumers. PMID:27042093

  1. Fluoride concentration in plaque in adolescents after topical application of different fluoride varnishes.

    Science.gov (United States)

    Sköld-Larsson, K; Modéer, T; Twetman, S

    2000-03-01

    The aim of the study was to measure the fluoride (F) concentration in plaque after a single topical application of different fluoride varnishes with contrasting levels of F. Thirty adolescents (12-17 years) with fixed orthodontic appliances were randomly assigned to one of three groups: Bifluoride (6% F), Duraphat (2.23% F) and Fluor Protector (0.1% F). The varnishes were applied after professional cleaning in one upper quadrant, leaving the opposite quadrant untreated according to the split-mouth technique. Pooled plaque samples from each quadrant were collected at baseline and 3 days, 7 days and 30 days after the varnish treatment, and fluoride was analysed by microdiffusion. All fluoride varnishes increased the fluoride concentration in plaque compared with baseline, and the mean values varied between 23 and 138 ng F/mg after 3 days, depending on varnish F concentration. Compared with the control quadrant, statistically significant elevations were recorded for Bifluoride after 3 days and 7 days and Duraphat after 3 days, while no significant differences were revealed in the Fluor Protector group. The fluoride concentration in plaque was back to baseline levels for all participants in the Duraphat group after 7 days, while some individuals in the Bifluoride and Fluor Protector groups still registered slightly increased levels after 30 days. The results suggest that fluoride varnish treatments resulted in elevated fluoride levels in plaque adjacent to fixed orthodontic appliances for a period of up to 1 week, although different patterns was disclosed for the various brands.

  2. Presence and Origin of Fluoride in the Complex Terminal Water of Ouargla Basin (Northern Sahara of Algeria

    Directory of Open Access Journals (Sweden)

    Imed E. Nezli

    2009-01-01

    Full Text Available Problem statement: The underground waters in the oriental regions of the Algerian Sahara, present real chemical quality problems. Their content in fluorides always exceeds the limit of the recommended levels. That is 0.8 mg L-1, according to the maximum temperature in the region. Combined to a high salinity, it affects the health of the population living around the region. The present work, deals with the presence of fluoride and the geochemical origin in the Complex Terminal aquifer of Ouargla, rarely examined in the Algerian Sahara. Approach: Is based on the following aspects: Sampling and physico-chemicals analysis of water, statistical treatment of the physico-chemical water parameters and simulation to natural and isotherm 25°C evaporation of water parameters. Results: The results show the presence of fluoride in the studied water. The rates vary between 1 and 2 mg L-1. The calculation of water saturation index in relation with the preponderant minerals, using the thermodynamic model ‹‹phreeqci›› reveals a sensitivity of carbonate minerals towards precipitation and dissolution of evaporitic minerals and clayey fluorides as well. Conclusions/Recommendations: The increasing alkalinity of water in contact with the aquifer during long periods of stay decreases the chemical activity of calcium and helps with alteration of clayey minerals and fluoride as a necessary condition for a possible fluorite mineralization. Knowing the origin of that fluoridation leads to possible solutions, through the optimization of a water treatment meets the standards.

  3. Determination of Fluoride in the Bottled Drinking Waters in Iran

    OpenAIRE

    Amanlou, Massoud; Hosseinpour, Maedeh; Azizian, Homa; Khoshayand, Mohammad Reza; Navabpoor, Mojtaba; Souri, Effat

    2010-01-01

    Fluoride is recognized as an effective agent for dental caries prevention. Generally, the main source of fluoride intake is drinking water. In this study, fluoride content in 18 commercial brands of bottled waters was investigated. Six samples from each batch of 18 Iranian commercial brands of bottled waters were supplied. The fluoride content of samples was analyzed by Fluoride Ion Selective Electrode. The mean ± SD fluoride content of the bottled waters was 0.202 ± 0.00152 mg/L with a range...

  4. Synthesis, physical and chemical properties, and potential applications of graphite fluoride fibers

    Science.gov (United States)

    Hung, Ching-Cheh; Long, Martin; Stahl, Mark

    1987-01-01

    Graphite fluoride fibers can be produced by fluorinating pristine or intercalated graphite fibers. The higher the degree of graphitization of the fibers, the higher the temperature needed to reach the same degree of fluorination. Pitched based fibers were fluorinated to flourine-to-carbon atom rations between 0 and 1. The graphite fluoride fibers with a fluorine-to-carbon atom ration near 1 have extensive visible structural damage. On the other hand, fluorination of fibers pretreated with bromine or fluorine and bromine result in fibers with a fluorine-to-carbon atom ratio nearly equal to 0.5 with no visible structural damage. The electrical resistivity of the fibers is dependent upon the fluorine to carbon atom ratio and ranged from .01 to 10 to the 11th ohm/cm. The thermal conductivity of these fibers ranged from 5 to 73 W/m-k, which is much larger than the thermal conductivity of glass, which is the regular filler in epoxy composites. If graphite fluoride fibers are used as a filler in epoxy or PTFE, the resulting composite may be a high thermal conductivity material with an electrical resistivity in either the insulator or semiconductor range. The electrically insulating product may provide heat transfer with lower temperature gradients than many current electrical insulators. Potential applications are presented.

  5. Caries inhibition by fluoride-releasing primers.

    Science.gov (United States)

    Kerber, L J; Donly, K J

    1993-10-01

    This study evaluated the caries inhibition of dentin primers with the addition of fluoride. Two standardized Class V preparations were placed in 20 molars, the gingival margin placed below the cementoenamel junction and the occlusal margin placed in enamel. Two dentin primers (Syntac and ScotchPrep) were placed in equal numbers of 20 preparations, according to manufacturer's instructions. Ammonium fluoride (10% by weight) was then added to these primers and they were placed in the remaining 20 preparations, opposing the non-fluoridated primer of the same system. All teeth were then restored with a non-fluoridated resin composite. All teeth were subjected to an artificial caries challenge (pH 4.2) for 5 days. Sections of 100 microns were obtained, photographed under polarized light microscopy, then demineralized areas were quantitated by digitization. Results demonstrated the mean areas (mm2 +/- S.D.) demineralization at 0.25 mm, 0.5 mm and 1.0 mm from the restoration margin to be: Syntac/fluoride (1.44 +/- 0.49, 1.68 +/- 0.54, 3.72 +/- 0.74); Syntac (1.99 +/- 0.58, 1.50 +/- 0.35, 2.98 +/- 1.26); ScotchPrep/fluoride (1.23 +/- 0.68, 1.55 +/- 0.64, 3.08 +/- 1.16); ScotchPrep (1.90 +/- 0.83, 1.71 +/- .038, 3.36 +/- 0.62). A paired t-test indicated primers with fluoride to demonstrate significantly less demineralization 0.25 mm from the restoration margin (P < 0.07). PMID:7880460

  6. Fluoride release and uptake abilities of different fissure sealants

    Science.gov (United States)

    Andenna, Gianluigi; Ceci, Matteo; Beltrami, Riccardo; Colombo, Marco; Cucca, Lucia

    2016-01-01

    Background The long-term capability of resin sealants and glass ionomer cements to release fluoride is associated to a reduction in pit and fissure caries. The regular use of fluoride varnishes/toothpastes can result in the absorption of fluoride into the sealant. The objective of the present study was to assess the fluoride release/uptake capacities of different fissure sealants. Material and Methods Three different fissure sealants (Fuji Triage/GC, Fissurit FX/Voco and Grandio Seal/Voco) were examined. Ten discs of each material were prepared. Each disc was incubated with distilled water and then the solution analyzed for diluted for fluoride concentration, using a combination of fluoride electrode (OrionGP 1 S/N 13824, Orion Research Inc, Boston, MA, USA) connected to an expandable ion analyzer (Orion 720A, Orion Research Inc, Boston, MA, USA). Standard curves between 1 and 100 ppm F- were used to calibrate the electrode. Cumulative fluoride release was measured on days 1, 2, 3, 5, 7, 21, 35 and 49, then two different fluoride varnishes/pastes (Profluorid Varnish/Voco, MI Paste Plus/GC), were applied to the sealants tested, and fluoride release (after reuptake) was measured on days 56, 70 and 84. Results Kruskal Wallis test confirmed significant differences in fluoride release between Fuji Triage/GC and Fissurit FX/Voco and Grandio Seal/Voco from day 1 (P fluoride varnish Profluorid Varnish enhanced the fluoride release for all sealants (P fluoride release for all sealants except for Fuji Triage/GC (P > 0.05). Conclusions The GIC-based sealant (Fuji Triage/GC) released significantly more fluoride than the resin sealants tested. The exposure to the fluoridated varnish (Profluorid Varnish) significantly recharged the sealants tested more than the CPP-ACPF toothpaste (MI Paste Plus). Key words:Fissure sealants, fluoride release, fluoride uptake, glass ionomer cements. PMID:27398179

  7. Thermodynamic data-base for metal fluorides

    International Nuclear Information System (INIS)

    This study is aimed at collecting useful data of thermodynamic properties of various metal fluorides. Many thermodynamic data for metal fluorides are needed for the effective development, but no report of data-base was published. Accordingly, the objective of this report is to rearrange systematically the existing thermodynamic data based on metal fluorides and is to use it as basic data for the development of pyrochemical process. The physicochemical properties of various metal fluorides and metals were collected from literature and such existing data base as HSC code, TAPP code, FACT code, JANAF table, NEA data-base, CRC handbook. As major contents of the thermodynamic data-base, the physicochemical properties such as formation energy, viscosity, density, vapor pressure, etc. were collected. Especially, some phase diagrams of eutectic molten fluorides are plotted and thermodynamic data of liquid metals are also compiled. In the future, the technical report is to be used as basic data for the development of the pyrochemical process which is being carried out as a long-term nuclear R and D project

  8. Thermodynamic data-base for metal fluorides

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Jae Hyung; Lee, Byung Gik; Kang, Young Ho and others

    2001-05-01

    This study is aimed at collecting useful data of thermodynamic properties of various metal fluorides. Many thermodynamic data for metal fluorides are needed for the effective development, but no report of data-base was published. Accordingly, the objective of this report is to rearrange systematically the existing thermodynamic data based on metal fluorides and is to use it as basic data for the development of pyrochemical process. The physicochemical properties of various metal fluorides and metals were collected from literature and such existing data base as HSC code, TAPP code, FACT code, JANAF table, NEA data-base, CRC handbook. As major contents of the thermodynamic data-base, the physicochemical properties such as formation energy, viscosity, density, vapor pressure, etc. were collected. Especially, some phase diagrams of eutectic molten fluorides are plotted and thermodynamic data of liquid metals are also compiled. In the future, the technical report is to be used as basic data for the development of the pyrochemical process which is being carried out as a long-term nuclear R and D project.

  9. Emissions of fluorides from welding processes.

    Science.gov (United States)

    Szewczyńska, Małgorzata; Pągowska, Emilia; Pyrzyńska, Krystyna

    2015-11-01

    The levels of fluoride airborne particulates emitted from welding processes were investigated. They were sampled with the patented IOM Sampler, developed by J. H. Vincent and D. Mark at the Institute of Occupational Medicine (IOM), personal inhalable sampler for simultaneous collection of the inhalable and respirable size fractions. Ion chromatography with conductometric detection was used for quantitative analysis. The efficiency of fluoride extraction from the cellulose filter of the IOM sampler was examined using the standard sample of urban air particle matter SRM-1648a. The best results for extraction were obtained when water and the anionic surfactant N-Cetyl-N-N-N-trimethylammonium bromide (CTAB) were used in an ultrasonic bath. The limits of detection and quantification for the whole procedure were 8μg/L and 24μg/L, respectively. The linear range of calibration was 0.01-10mg/L, which corresponds to 0.0001-0.1mg of fluorides per m(3) in collection of a 20L air sample. The concentration of fluorides in the respirable fraction of collected air samples was in the range of 0.20-1.82mg/m(3), while the inhalable fraction contained 0.23-1.96mg/m(3) of fluorides during an eight-hour working day in the welding room. PMID:26574102

  10. Removing Fluoride Ions with Continously Fed Activated Alumina.

    Science.gov (United States)

    Wu, Yeun C.; Itemaking, Isara Cholapranee

    1979-01-01

    Discussed is the mathematical basis for determining fluoride removal during water treatment with activated alumina. The study indicates that decreasing particle size decreases the pore diffusion effect and increases fluoride removal. (AS)

  11. Direct measurement of gas solubility and diffusivity in poly(vinylidene fluoride) with a high-pressure microbalance

    DEFF Research Database (Denmark)

    von Solms, Nicolas; Zecchin, Nicoletta; Rubin, Adam;

    2005-01-01

    We present solubility and diffusion data for the gases methane and carbon dioxide in the polymer poly(vinylidene fluoride). The polymer was cut from extruded piping intended for use in offshore oil and gas applications. Measurements were carried out using a purpose-built high-pressure microbalance...

  12. [18F]Fluoride recovery via gaseous [18F]HF

    DEFF Research Database (Denmark)

    Mathiessen, Bente; Jensen, Mikael; Zhuravlev, Fedor

    2011-01-01

    Acidification of target water with H2SO4 in a specially constructed glassy carbon/polyethylene apparatus allowed for recovery of up to 82% of [18F]fluoride as [18F]HF gas. The [18F]HF distillate was found to be acid-free but moist; when passed through a solution of tBuPh2SiOTf, it yielded [18F...

  13. Inorganic nanotubes reinforced polyvinylidene fluoride composites as low-cost electromagnetic interference shielding materials

    OpenAIRE

    Sankaranarayanan Venkataraman; Eswaraiah Varrla; Ramaprabhu Sundara

    2011-01-01

    Abstract Novel polymer nanocomposites comprising of MnO2 nanotubes (MNTs), functionalized multiwalled carbon nanotubes (f-MWCNTs), and polyvinylidene fluoride (PVDF) were synthesized. Homogeneous distribution of f-MWCNTs and MNTs in PVDF matrix were confirmed by field emission scanning electron microscopy. Electrical conductivity measurements were performed on these polymer composites using four probe technique. The addition of 2 wt.% of MNTs (2 wt.%, f-MWCNTs) to PVDF matrix results in an in...

  14. Uranyl fluoride luminescence in acidic aqueous solutions

    International Nuclear Information System (INIS)

    Luminescence emission spectra and decay rates are reported for uranyl species in acidic aqueous solutions containing HF or added NaF. The longest luminescence lifetime, 0.269 ± 0.006 ms, was observed from uranyl in 1 M HF + 1 M HClO4 at 296 K and decreased with increasing temperature. Based on a luminescence dynamics model that assumes equilibrium among electronically excited uranyl fluoride species and free fluoride ion, this long lived uranyl luminescence in aqueous solution is attributed primarily to UO2F2. Studies on the effect of added LiNO3 or Na2WO4·2H2O showed relatively weak quenching of uranyl fluoride luminescence which suggests that high sensitivity determination of the UF6 content of WF6 gas should be feasible via uranyl luminescence analysis of hydrolyzed gas samples of impure WF6

  15. Cancer incidence and mortality in workers exposed to fluoride

    DEFF Research Database (Denmark)

    Grandjean, P; Olsen, J H; Jensen, O M;

    1992-01-01

    Although a recent bioassay showed increased frequency of bone cancer in rats with high oral intake of fluoride, the data are reported as equivocal evidence of carcinogenicity. In humans, occupational fluoride exposure may cause skeletal fluorosis, and our earlier follow-up of fluoride...

  16. 40 CFR 180.575 - Sulfuryl fluoride; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Sulfuryl fluoride; tolerances for... § 180.575 Sulfuryl fluoride; tolerances for residues. (a)(1) General. Tolerances are established for residues of sulfuryl fluoride in or on the following commodities from the postharvest fumigation...

  17. 21 CFR 177.2510 - Polyvinylidene fluoride resins.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyvinylidene fluoride resins. 177.2510 Section... as Components of Articles Intended for Repeated Use § 177.2510 Polyvinylidene fluoride resins. Polyvinylidene fluoride resins may be safely used as articles or components of articles intended for repeated...

  18. COMPLEX FLUORIDES OF PLUTONIUM AND AN ALKALI METAL

    Science.gov (United States)

    Seaborg, G.T.

    1960-08-01

    A method is given for precipitating alkali metal plutonium fluorides. such as KPuF/sub 5/, KPu/sub 2/F/sub 9/, NaPuF/sub 5/, and RbPuF/sub 5/, from an aqueous plutonium(IV) solution by adding hydrogen fluoride and alkali-metal- fluoride.

  19. 40 CFR 60.212 - Standard for fluorides.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for fluorides. 60.212 Section... Industry: Superphosphoric Acid Plants § 60.212 Standard for fluorides. (a) On and after the date on which... facility any gases which contain total fluorides in excess of 5.0 g/megagram (Mg) of equivalent P2O5...

  20. 40 CFR 60.222 - Standard for fluorides.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for fluorides. 60.222 Section... Industry: Diammonium Phosphate Plants § 60.222 Standard for fluorides. (a) On and after the date on which... facility any gases which contain total fluorides in excess of 30 g/megagram (Mg) of equivalent P2O5 feed...

  1. 40 CFR 60.242 - Standard for fluorides.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for fluorides. 60.242 Section... Industry: Granular Triple Superphosphate Storage Facilities § 60.242 Standard for fluorides. (a) On and... atmosphere from any affected facility any gases which contain total fluorides in excess of 0.25...

  2. 40 CFR 60.232 - Standard for fluorides.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for fluorides. 60.232 Section... Industry: Triple Superphosphate Plants § 60.232 Standard for fluorides. On and after the date on which the... gases which contain total fluorides in excess of 100 g/megagram (Mg) of equivalent P2O5 feed (0.20...

  3. Health effects of fluoride pollution caused by coal burning

    Energy Technology Data Exchange (ETDEWEB)

    Ando, M.; Tadano, M.; Yamamoto, S.; Tamura, K.; Chen, X. [Regional Environment Division, National Institute for Environmental Studies, Tsukuba, 305-0083 Ibaraki (Japan); Asanuma, S. [Japan Institute of Rural Medicine, Usuda, Nagano (Japan); Watanabe, T. [Saku Central Hospital, Usuda, Nagano (Japan); Kondo, T. [Matsumoto Dental College, Shiojiri, Nagano (Japan); Sakurai, S. [Otsuma Women' s University, Tama, Tokyo (Japan); Ji, R.; Liang, C.; Cao, S. [Institute of Environmental Health and Engineering, Beijing (China); Hong, Z. [Shanxi Maternity and Children' s Hospital, Taiyuan (China)

    2001-04-23

    Recently a huge amount of fluoride in coal has been released into indoor environments by the combustion of coal and fluoride pollution seems to be increasing in some rural areas in China. Combustion of coal and coal bricks is the primary source of gaseous and aerosol fluoride and these forms of fluoride can easily enter exposed food products and the human respiratory tract. Major human fluoride exposure was caused by consumption of fluoride contaminated food, such as corn, chilies and potatoes. For each diagnostic syndrome of dental fluorosis, a log-normal distribution was observed on the logarithm of urinary fluoride concentration in students in China. Urinary fluoride content was found to be a primary health indicator of the prevalence of dental fluorosis in the community. In the fluorosis areas, osteosclerosis in skeletal fluorosis patients was observed with a high prevalence. A biochemical marker of bone resorption, urinary deoxypyridinoline content was much higher in residents in China than in residents in Japan. It was suggested that bone resorption was stimulated to a greater extent in residents in China and fluoride may stimulate both bone resorption and bone formation. Renal function especially glomerular filtration rate was very sensitive to fluoride exposure. Inorganic phosphate concentrations in urine were significantly lower in the residents in fluorosis areas in China than in non-fluorosis area in China and Japan. Since airborne fluoride from the combustion of coal pollutes extensively both the living environment and food, it is necessary to reduce fluoride pollution caused by coal burning.

  4. Plasma processing of fluoride solutions of refractory rare metals

    Energy Technology Data Exchange (ETDEWEB)

    Gutsol, A.F. [Institute of Chemistry and Technology of Less-Common Elements and Raw Materials, Murmanskaya oblast` (Russian Federation)

    1995-09-01

    Features of plasma processing of fluoride solutions of refractory metals were studied. It was shown that pyrohydrolysis of niobium, tantalum, and titanium fluorides occurs in the gas phase, thus providing fine oxide powders. The pyrohydrolysis of low-volatility zirconium fluoride occurs in the solid phase, yielding oxide particles corresponding to the size of initial droplets.

  5. Onderzoek naar de bepaling van fluoride in een doorstroomsysteem

    NARCIS (Netherlands)

    Neele J; Nagtegaal-Wouterse GWM; Reijnders HFR

    1989-01-01

    Een snelle methode voor de bepaling van fluoride in een doorstroomsysteem met potentiometrische detectie en een lage onderste analysegrens is ontwikkeld. De mate waarin fluoride uit fluoride-verbindingen wordt vrijgemaakt door complexvormende stoffen is gevolgd om vast te stellen hoeveel tijd hierv

  6. Synthesis of reagents for fluoride technologies

    Institute of Scientific and Technical Information of China (English)

    Gordienko; P.; S.; Kolzunov; V.; A.; Dostovalov; V.; A.; Kaidalova; T.; A.

    2005-01-01

    Growing demand for fluorinating reagents to be used in rare-metal industry has stimulated conducting research in the field of production for these reagents. That is why the fluorinating reagents production has recently formed an independent segment of industry. Main industrial fluorinating reagents include hydrofluoric acid, anhydrous hydrogen fluoride, technical ammonium hydrodifluoride, fluorosilicic acid and its salts. To produce technical etching acid, fluor-spar with calcium fluoride content at least 92% is used in most cases. To produce anhydrous hydrogen fluoride, fluor-spar with calcium fluoride content 96 %-97 % is necessary. The fluorine-containing raw materials refinement from silica by means of flotation makes the fluorinating reagents production substantially more expensive. In this work we have attempted to process unconcentrated raw materials by fluorine removal in the form of volatile silicon tetrafluoride. In this process silicon tetrafluoride was recovered by liquid ammonia with subsequent hydrolysis of the formed ammonia hexafluorosilicate. Hydrolysis occurred according to the reaction:(NH4)2 SiF6 + 4NH3 + 2 H2O= 6NH4F+ SiO2 The products of the ammonia hexafluorosilicate hydrolysis included ammonia fluoride and amorphous silica gel ("white soot") as by-product. This "white soot" was of high purity-with main component content 99.95% and total admixture content 0.05%. Silica gel is a superfine material with specific surface of 267.6 m2/g and is recommended as filler in the production of rubber, plastics and for other applications.Ammonia fluoride was transformed into ammonia hydrodifluoride (main processing product) according to the reaction:2NH4F→NH3+NH4 HF2 It was stated that the NH4F: NH4 HF2 ratio depends on boiling point temperature-with its increase the ammonia hydrofluoride concentration in solution increases as well.

  7. Enhanced fluoride sorption by mechanochemically activated kaolinites.

    Science.gov (United States)

    Meenakshi, S; Sundaram, C Sairam; Sukumar, Rugmini

    2008-05-01

    Kaolinite clay obtained from the mines was processed and studied for its fluoride sorption capacity. The surface area of the clay mineral was increased from 15.11 m(2)/g (raw) to 32.43 m(2)/g (activated) by mechanochemical activation. Batch adsorption studies were conducted to optimize various equilibrating conditions like the effect of contact time, dosage, pH for both raw and micronized kaolinites (RK and MK). The effect of other interfering anions on the defluoridation capacity (DC) of the sorbents was studied. Sorption of fluoride by the sorbents was observed over a wide pH range of 3-11. The studies revealed there is an enhanced fluoride sorption on MK. FTIR and XRD were used for the characterization of the sorbent. The surface morphology of the clay material was observed using SEM. The adsorption of fluoride was studied at three different temperatures, viz., 303, 313 and 323 K. The sorption data obtained at optimized conditions were subjected to Freundlich and Langmuir isotherms. Sorption intensity (1/n) (0.770-0.810) has been evaluated using Freundlich isotherm, whereas the values of sorption capacity Q(0) (0.609, 0.714 and 0.782 mg/g) and binding energy b (0.158, 0.145 and 0.133 L/mg) at three different temperatures have been estimated using Langmuir isotherm. Adsorption process was found to be controlled by both Freundlich and Langmuir isotherms. Thermodynamic studies revealed that the sorption of fluoride on MK is endothermic and a spontaneous process. The kinetic studies indicate that the sorption of fluoride on MK follows pseudo-first-order and intraparticle diffusion models.

  8. Enhanced fluoride sorption by mechanochemically activated kaolinites

    Energy Technology Data Exchange (ETDEWEB)

    Meenakshi, S. [Department of Chemistry, Gandhigram Rural University, Gandhigram 624302, Tamilnadu (India)], E-mail: drs_meena@rediffmail.com; Sundaram, C. Sairam [Department of Science and Humanities, Karaikal Polytechnic College, Karaikal 609609, Puducherry (India); Sukumar, Rugmini [Chemical Sciences and Technologies, Regional Research Laboratory, Trivandrum 695019, Kerala (India)

    2008-05-01

    Kaolinite clay obtained from the mines was processed and studied for its fluoride sorption capacity. The surface area of the clay mineral was increased from 15.11 m{sup 2}/g (raw) to 32.43 m{sup 2}/g (activated) by mechanochemical activation. Batch adsorption studies were conducted to optimize various equilibrating conditions like the effect of contact time, dosage, pH for both raw and micronized kaolinites (RK and MK). The effect of other interfering anions on the defluoridation capacity (DC) of the sorbents was studied. Sorption of fluoride by the sorbents was observed over a wide pH range of 3-11. The studies revealed there is an enhanced fluoride sorption on MK. FTIR and XRD were used for the characterization of the sorbent. The surface morphology of the clay material was observed using SEM. The adsorption of fluoride was studied at three different temperatures, viz., 303, 313 and 323 K. The sorption data obtained at optimized conditions were subjected to Freundlich and Langmuir isotherms. Sorption intensity (1/n) (0.770-0.810) has been evaluated using Freundlich isotherm, whereas the values of sorption capacity Q{sup 0} (0.609, 0.714 and 0.782 mg/g) and binding energy b (0.158, 0.145 and 0.133 L/mg) at three different temperatures have been estimated using Langmuir isotherm. Adsorption process was found to be controlled by both Freundlich and Langmuir isotherms. Thermodynamic studies revealed that the sorption of fluoride on MK is endothermic and a spontaneous process. The kinetic studies indicate that the sorption of fluoride on MK follows pseudo-first-order and intraparticle diffusion models.

  9. Electrodeposited apatite coating for solid-phase microextraction and sensitive indirect voltammetric determination of fluoride ions.

    Science.gov (United States)

    Mao, Yuehong; Chen, Yufei; Chu, Lin; Zhang, Xiaoli

    2013-10-15

    Electrodeposition was used to prepare a new solid phase microextraction (SPME) coatings. Two apatite SPME coatings, dicalcium phosphate dihydrate (DCPD or brushite) and hydroxyapatite (HAP) were validly and homogeneously one-step electrodeposited on glassy carbon electrode (GCE) under different conditions. The coatings were characterized by XRD, FTIR, SEM, CV and EIS. The apatite SPME coatings showed excellent and selective adsorbability to fluoride ions. A novel indirect voltammetric strategy for sensitive detection of fluoride was proposed using K3Fe(CN)6 as indicating probe. The detection principle of fluoride ions was based on the increment of steric hindrance after fluoride adsorption, which resulting in the decrease of the amperometric signal to Fe(CN)6(3-). The liner ranges were 0.5-20.0 μmol/L for n-DCPD/GCE with the limit of detection of 0.14 μmol/L and 0.1-50.0 μmol/L for n-HAP/GCE with the limit of detection of 0.069 μmol/L, respectively. The developed method was applied to the analysis of water samples (lake, spring and tap water) and the recovery values were found to be in the range of 90-106%. PMID:24054624

  10. Metabolomic Effects of Xylitol and Fluoride on Plaque Biofilm in Vivo

    Science.gov (United States)

    Takahashi, N.; Washio, J.

    2011-01-01

    Dental caries is initiated by demineralization of the tooth surface through acid production from sugar by plaque biofilm. Fluoride and xylitol have been used worldwide as caries-preventive reagents, based on in vitro-proven inhibitory mechanisms on bacterial acid production. We attempted to confirm the inhibitory mechanisms of fluoride and xylitol in vivo by performing metabolome analysis on the central carbon metabolism in supragingival plaque using the combination of capillary electrophoresis and a time-of-flight mass spectrometer. Fluoride (225 and 900 ppm F−) inhibited lactate production from 10% glucose by 34% and 46%, respectively, along with the increase in 3-phosphoglycerate and the decrease in phosphoenolpyruvate in the EMP pathway in supragingival plaque. These results confirmed that fluoride inhibited bacterial enolase in the EMP pathway and subsequently repressed acid production in vivo. In contrast, 10% xylitol had no effect on acid production and the metabolome profile in supragingival plaque, although xylitol 5-phosphate was produced. These results suggest that xylitol is not an inhibitor of plaque acid production but rather a non-fermentative sugar alcohol. Metabolome analyses of plaque biofilm can be applied for monitoring the efficacy of dietary components and medicines for plaque biofilm, leading to the development of effective plaque control. PMID:21940519

  11. Studies of niobium electrocrystallization phenomena in molten fluorides

    International Nuclear Information System (INIS)

    The electrodeposition of niobium from NbCl5 or K2NbF7, dissolved in molten alkaline fluorides (LiF/NaF), in the 700--800 C temperature range has been studied by using cyclic voltammetry, chronopotentiometry, and chronoamperometry. A linear relationship between the NbIV diffusion coefficient and the temperature was found in the cyclic voltammograms and chronopotentiograms. Scanning electron micrography shows that the shape of the nuclei is hemispherical. Chronoamperometric results show that the deposition process involves instantaneous nucleation with diffusion-controlled growth of the nuclei. The influence of temperature, overpotential, and substrate (copper, stainless steel, vitreous carbon) on the nuclear site densities is also considered

  12. Reconstructing temporal variation of fluoride uptake in eastern grey kangaroos (Macropus giganteus) from a high-fluoride area by analysis of fluoride distribution in dentine.

    Science.gov (United States)

    Kierdorf, Horst; Rhede, Dieter; Death, Clare; Hufschmid, Jasmin; Kierdorf, Uwe

    2016-04-01

    Trace element profiling in the incrementally formed dentine of mammalian teeth can be applied to reconstruct temporal variation of incorporation of these elements into the tissue. Using an electron microprobe, this study analysed fluoride distribution in dentine of first and third mandibular molars of free-ranging eastern grey kangaroos inhabiting a high-fluoride area, to assess temporal variation in fluoride uptake of the animals. Fluoride content in the early-formed dentine of first molars was significantly lower than in the late-formed dentine of these teeth, and was also lower than in both, the early and the late-formed dentine of third molars. As early dentine formation in M1 takes place prior to weaning, this finding indicates a lower dentinal fluoride uptake during the pre-weaning compared to the post-weaning period. This is hypothetically attributed to the action of a partial barrier to fluoride transfer from blood to milk in lactating females and a low bioavailability of fluoride ingested together with milk. Another factor contributing to lower plasma fluoride levels in juveniles compared to adults is the rapid clearance of fluoride from blood plasma in the former due to their intense skeletal growth. The combined action of these mechanisms is considered to explain why in kangaroos from high-fluoride areas, the (early-formed) first molars are not affected by dental fluorosis while the (later-formed) third and fourth molars regularly exhibit marked to severe fluorotic lesions. PMID:26736058

  13. Comparative evaluation of fluoride release from PRG-composites and compomer on application of topical fluoride: An in-vitro study

    Directory of Open Access Journals (Sweden)

    Dhull K

    2009-03-01

    Full Text Available Aims and Objective: To determine the fluoride release from Giomer and Compomer, using different topical fluoride regimes, and to compare the amount of fluoride release from giomer with that of compomer. Materials and Method: Forty-eight specimens of each giomer and compomer were divided into four treatment groups, namely, control group, fluoridated dentifrice (500 ppm once daily group, fluoridated dentifrice (500 ppm twice daily group, fluoridated dentifrice (500 ppm once daily + fluoridated mouthwash (225 ppm group. Each specimen was suspended in demineralizing solution for six hours and remineralizing solution for 18 hours. Fluoride release was measured in both the demineralizing solution and remineralizing solution daily for seven days. Total daily fluoride release for each specimen was calculated by adding the amount released in the demineralizing solution to that released in remineralizing solution. Results and Conclusion: The fluoride release (ppm was found to be more in Giomer when compared to Compomer. The fluoride released from Giomer and Compomer was significantly greater in the acidic demineralizing solution than in the neutral remineralizing solution. It was found that increasing fluoride exposure significantly increased fluoride release from the giomer and compomer. It was found that the fluoride release from the subgroups of giomer and compomer was in the following order: fluoridated dentifrice twice daily > fluoridated dentifrice once daily + fluoridated mouthwash > fluoridated dentifrice once daily > control group. It was found that the giomer showed a greater fluoride uptake than the compomer.

  14. Some electronic and magnetic properties of Fluoride ion in Fluoride structure nanocrystals

    Science.gov (United States)

    Imtani, Ali Nasir

    2012-01-01

    We have investigated the effects of the environment potential around Fluoride ion on some important electronic and magnetic properties such as dipole polarisability, moment of oscillator strengths S(k) and magnetic susceptibility. The theoretical procedure is based on the variational-perturbation theory with two parameter trial functions incorporated in an ionic model. We estimate these properties in four cases for Fluoride ion; free ion, ion under different potentials, ion in the crystals and ion in nanocrystal, CdF2, CaF2, PbF2, SrF2 and BaF2. Our results indicate that these properties vary with ion environments and the free state of Fluoride ion has higher values and there is linearity behaviour of these properties with lattice constant. For Fluoride ion in nanocrystal, we have found that there is an extra parameter that can also affect the dipole polarisability, the number of ions in the structure.

  15. Fluoride in Drinking Water -Its Effects and Removal

    Directory of Open Access Journals (Sweden)

    Ram Gopal

    1985-01-01

    Full Text Available Occurrence of fluoride in water, its metabolism, excretion. effect oingestion in human and cattle system and methods of fluoridation and defluoridation have been discussed. The presence of fluoride in waters occurring in India, with special reference to Rajasthan desert has been reviewed. Based on the survey and physico-chemical analyses of about 2,700 water samples of Rajasthan, distribution of fluoride in this area has been discussed wrth reference to drinking water standards. A water resources map showing concentrations of fluoride in four arid districts of Rajasthan is also presented.

  16. Oral Fluoride Including Drinking Water in Prevention of Tooth Decay

    OpenAIRE

    Vitoria I

    2015-01-01

    Herein we present a review of the role of oral fluoride in the prevention of tooth decay, together with updated recommendations on fluoride supplements. Fluoridation of public drinking water is still considered effective, but the recommended level of fluoride is now 0.7 mg/L, compared with the previously recommended range of 0.7-1.2 mg/L. Oral fluoride supplements are currently not restricted to the children at high risk for tooth decay, but recommended initiate at 6 months&nbs...

  17. Fluoride: a risk factor for inflammatory bowel disease?

    Science.gov (United States)

    Follin-Arbelet, Benoit; Moum, Bjørn

    2016-09-01

    Although the association between inflammatory bowel disease (IBD) and oral hygiene has been noticed before, there has been little research on prolonged fluoride exposure as a possible risk factor. In the presented cases, exposure to fluoride seems indirectly associated with higher incidence of IBD. Fluoride toxicology and epidemiology documents frequent unspecific chronic gastrointestinal symptoms and intestinal inflammation. Efflux genes that confer resistance to environmental fluoride may select for IBD associated gut microbiota and therefore be involved in the pathogenesis. Together these multidisciplinary results argue for further investigation on the hypothesis of fluoride as a risk factor for IBD. PMID:27199224

  18. Manufacture of high purity low arsenic anhydrous hydrogen fluoride

    International Nuclear Information System (INIS)

    A process for manufacturing anhydrous hydrogen fluoride with reduced levels of arsenic impurity from arsenic contaminated anhydrous hydrogen fluoride is described which comprises: (a) contacting the anhydrous hydrogen fluoride with an effective amount of hydrogen peroxide to oxidize the arsenic impurity in the presence of a catalyst which comprises a catalytic amount of (i) molybdenum or an inorganic molybdenum compound and (ii) a phosphate compound, at a temperature and for a period of time sufficient to oxidize volatile trivalent arsenic impurities in the anhydrous hydrogen fluoride to non-volatile pentavalent arsenic compounds, and (b) distilling the resulting mixture and recovering anhydrous hydrogen fluoride with reduced levels of arsenic impurity

  19. Total Fluoride Intake by Children from a Tropical Brazilian City.

    Science.gov (United States)

    Lima, Carolina V; Cury, Jaime A; Vale, Glauber C; Lima, Marina D M; Moura, Lúcia de Fátima A D; Moura, Marcoeli Silva de

    2015-01-01

    The main sources of fluoride intake by children are fluoridated water and toothpaste. Little has been studied regarding fluoride intake from these sources in regions with tropical climates and high temperatures throughout the year. This study aimed to determine the amount of fluoride ingested from diet and tooth brushing by children who live in a city with a tropical climate. Sixty-seven children from Teresina, Piauí, Brazil, took part in this study. The city's water supply was optimally fluoridated. The duplicate-diet method was used to determine the fluoride intake from diet. The intake of fluoride from dentifrice was determined by subtracting the amount of fluoride placed on the toothbrush and that recovered after brushing. The concentration of fluoride was measured using an ion-specific electrode and is expressed as milligrams/kilogram of body weight/day. The mean (±SD) total amount was 0.071 ± 0.036 mg F/kg body weight/day, and the relative contributions of diet and toothpaste were 0.025 ± 0.010 and 0.046 ± 0.035, respectively. The factors associated with fluoride intake from toothpaste were: use of children's toothpaste (p = 0.003), use of large amounts of toothpaste (p fluorosis risk. The results suggest that the amount of fluoride ingested by most children who live in a Brazilian city with a tropical climate is considered safe in terms of the risk of dental fluorosis. PMID:26655142

  20. Estimation of atmospheric fluoride by limed filter papers

    International Nuclear Information System (INIS)

    The limed filter paper method of static sampling of atmospheric fluoride is reviewed in this report. Use of the technique, in conjunction with precise measurement of the absorbed fluoride and calibration with dynamic air sampling techniques, to estimate atmospheric fluoride levels, is considered to give only qualitative data (± 50%). The limed filter paper method is site specific due to variations in meteorological conditions. Its main value is to indicate seasonal and annual trends in fluoride exposure of vegetation. Subject to these considerations, the lower and upper limits of atmospheric fluoride exposure and the applicability to atmospheric fluoride estimation under routine or emergency fluoride release conditions are discussed, with special emphasis on the limiting factors

  1. FLUORIDE CONTENT OF COMMERCIALLY AVAILABLE SOY MILK PRODUCTS IN THAILAND.

    Science.gov (United States)

    Rirattanapong, Opas; Rirattanapong, Praphasri

    2016-01-01

    Abstract. In Thailand, the consumption of soy milk products is common but there is limited data about their fluoride content. The purpose of this study was to es- timate the fluoride content of soy milk products available in Thailand. Fluoride content was determined for 76 brands of soy milk using a F-ion-specific electrode. The fluoride concentrations ranged from 0.01 to 3.78 μg/ml. The fluoride content was not related to sugar content, soy bean content or the sterilization process. Among 3 brands of soy milk containing tea powder extract, the fluoride content was high (1.25 to 3.78 μg/ml). Most brands of soy milk tested in our study had fluoride content below the optimal daily intake but brands containing tea powder extract if consumed by children may increase their risk for fluorosis. PMID:27086437

  2. Fluoride in the prey of barn owls (Tyto alba).

    Science.gov (United States)

    Thomson, A G

    1987-01-01

    Bone fluoride in short-tailed voles (Microtus agrestis) and common shrews (Sorex araneus), the prey of barn owls (Tyto alba), was studied on Anglesey, North Wales. The average fluoride content of M. agrestis skulls obtained from a location 0.9 km from an aluminium reduction plant was significantly greater than that of skulls from another location 22 km from the source of industrial fluoride pollution. At both locations, mean fluoride levels of skulls extracted from owl pellets and those of voles trapped mechanically were broadly similar but important differences existed. Near the aluminium reduction plant, owls caught voles and shrews with a much wider range of fluoride levels than occurred at a single trapping site. However, there was no evidence for selection of heavily fluoridated prey. Within 1 km of the aluminium reduction plant, six trapping sites yielded S. araneus with a fourfold difference between the highest and lowest mean bone fluoride level. PMID:15092770

  3. Estimated Fluoride Doses from Toothpastes Should be Based on Total Soluble Fluoride

    Directory of Open Access Journals (Sweden)

    Jaime A. Cury

    2013-11-01

    Full Text Available The fluoride dose ingested by young children may be overestimated if based on levels of total fluoride (TF rather than levels of bioavailable fluoride (total soluble fluoride—TSF in toothpaste. The aim of the present study was to compare doses of fluoride intake based on TF and TSF. Fluoride intake in 158 Brazilian children aged three and four years was determined after tooth brushing with their usual toothpaste (either family toothpaste (n = 80 or children’s toothpaste (n = 78. The estimated dose (mg F/day/Kg of body weight of TF or TSF ingested was calculated from the chemical analysis of the toothpastes. Although the ingested dose of TF from the family toothpastes was higher than that from the children’s toothpastes (0.074 ± 0.007 and 0.039 ± 0.003 mg F/day/Kg, respectively; p 0.05. The fluoride dose ingested by children from toothpastes may be overestimated if based on the TF of the product. This finding suggests that the ingested dose should be calculated based on TSF. Dose of TSF ingested by children is similar whether family or children’s toothpaste is used.

  4. Solid electrolytes for fluoride ion batteries: ionic conductivity in polycrystalline tysonite-type fluorides.

    Science.gov (United States)

    Rongeat, Carine; Reddy, M Anji; Witter, Raiker; Fichtner, Maximilian

    2014-02-12

    Batteries based on a fluoride shuttle (fluoride ion battery, FIB) can theoretically provide high energy densities and can thus be considered as an interesting alternative to Li-ion batteries. Large improvements are still needed regarding their actual performance, in particular for the ionic conductivity of the solid electrolyte. At the current state of the art, two types of fluoride families can be considered for electrolyte applications: alkaline-earth fluorides having a fluorite-type structure and rare-earth fluorides having a tysonite-type structure. As regard to the latter, high ionic conductivities have been reported for doped LaF3 single crystals. However, polycrystalline materials would be easier to implement in a FIB due to practical reasons in the cell manufacturing. Hence, we have analyzed in detail the ionic conductivity of La(1-y)Ba(y)F(3-y) (0 ≤ y ≤ 0.15) solid solutions prepared by ball milling. The combination of DC and AC conductivity analyses provides a better understanding of the conduction mechanism in tysonite-type fluorides with a blocking effect of the grain boundaries. Heat treatment of the electrolyte material was performed and leads to an improvement of the ionic conductivity. This confirms the detrimental effect of grain boundaries and opens new route for the development of solid electrolytes for FIB with high ionic conductivities. PMID:24444763

  5. Actinide measurements by AMS using fluoride matrices

    Science.gov (United States)

    Cornett, R. J.; Kazi, Z. H.; Zhao, X.-L.; Chartrand, M. G.; Charles, R. J.; Kieser, W. E.

    2015-10-01

    Actinides can be measured by alpha spectroscopy (AS), mass spectroscopy or accelerator mass spectrometry (AMS). We tested a simple method to separate Pu and Am isotopes from the sample matrix using a single extraction chromatography column. The actinides in the column eluent were then measured by AS or AMS using a fluoride target matrix. Pu and Am were coprecipitated with NdF3. The strongest AMS beams of Pu and Am were produced when there was a large excess of fluoride donor atoms in the target and the NdF3 precipitates were diluted about 6-8 fold with PbF2. The measured concentrations of 239,240Pu and 241Am agreed with the concentrations in standards of known activity and with two IAEA certified reference materials. Measurements of 239,240Pu and 241Am made at A.E. Lalonde AMS Laboratory agree, within their statistical uncertainty, with independent measurements made using the IsoTrace AMS system. This work demonstrated that fluoride targets can produce reliable beams of actinide anions and that the measurement of actinides using fluorides agree with published values in certified reference materials.

  6. Water fluoridation in 40 Brazilian cities: 7 year analysis

    Directory of Open Access Journals (Sweden)

    Suzely Adas Saliba MOIMAZ

    2013-01-01

    Full Text Available Objectives Fluoride levels in the public water supplies of 40 Brazilian cities were analyzed and classified on the basis of risk/benefit balance. Material and Methods Samples were collected monthly over a seven-year period from three sites for each water supply source. The samples were analyzed in duplicate in the laboratory of the Center for Research in Public Health - UNESP using an ion analyzer coupled to a fluoride-specific electrode. Results A total of 19,533 samples were analyzed, of which 18,847 were artificially fluoridated and 686 were not artificially fluoridated. In samples from cities performing water fluoridation, 51.57% (n=9,720 had fluoride levels in the range of 0.55 to 0.84 mg F/L; 30.53% (n=5,754 were below 0.55 mg F/L and 17.90% (n=3,373 were above 0.84 mg F/L (maximum concentration=6.96 mg F/L. Most of the cities performing fluoridation that had a majority of samples with fluoride levels above the recommended parameter had deep wells and more than one source of water supply. There was some variability in the fluoride levels of samples from the same site and between collection sites in the same city. Conclusions The majority of samples from cities performing fluoridation had fluoride levels within the range that provides the best combination of risks and benefits, minimizing the risk of dental fluorosis while preventing dental caries. The conduction of studies about water distribution systems is suggested in cities with high natural fluoride concentrations in order to optimize the use of natural fluoride for fluoridation costs and avoid the risk of dental fluorosis.

  7. Effects of fluoridated milk on root dentin remineralization.

    Directory of Open Access Journals (Sweden)

    Wolfgang H Arnold

    Full Text Available The prevalence of root caries is increasing with greater life expectancy and number of retained teeth. Therefore, new preventive strategies should be developed to reduce the prevalence of root caries. The aim of this study was to investigate the effects of fluoridated milk on the remineralization of root dentin and to compare these effects to those of sodium fluoride (NaF application without milk.Thirty extracted human molars were divided into 6 groups, and the root cementum was removed from each tooth. The dentin surface was demineralized and then incubated with one of the following six solutions: Sodium chloride NaCl, artificial saliva, milk, milk+2.5 ppm fluoride, milk+10 ppm fluoride and artificial saliva+10 ppm fluoride. Serial sections were cut through the lesions and investigated with polarized light microscopy and quantitative morphometry, scanning electron microscopy (SEM and energy-dispersive X-ray spectroscopy (EDS. The data were statistically evaluated using a one-way ANOVA for multiple comparisons.The depth of the lesion decreased with increasing fluoride concentration and was the smallest after incubation with artificial saliva+10 ppm fluoride. SEM analysis revealed a clearly demarcated superficial remineralized zone after incubation with milk+2.5 ppm fluoride, milk+10 ppm fluoride and artificial saliva+10 ppm fluoride. Ca content in this zone increased with increasing fluoride content and was highest after artificial saliva+10 ppm fluoride incubation. In the artificial saliva+10 ppm fluoride group, an additional crystalline layer was present on top of the lesion that contained elevated levels of F and Ca.Incubation of root dentin with fluoridated milk showed a clear effect on root dentin remineralization, and incubation with NaF dissolved in artificial saliva demonstrated a stronger effect.

  8. Fluoride uptake into the developing enamel and dentine of sheep incisors following daily ingestion of fluoridated milk or water

    International Nuclear Information System (INIS)

    The caries preventive action of fluoride is common knowledge, although some of the mechanisms involved remain equivocal. At present, raised local levels of fluoride at, or in, the surface of tooth enamel is the most commonly accepted explanation of the anti-cariogenic action of fluoride. However, fluoride incorporated as fluorapatite into the tooth during its formation remains a possible alternative or complementary anti-cariogenic mechanism. If so, regular ingestion of fluoride during tooth formation is beneficial. Although use of fluoridated water is the preferred method in public health programmes, access to suitable potable water is required, and often this in not feasible. Fresh, preserved, or dried cow's milk products are widely used as nutritional and dietary items in most populations, particularly for young children. Milk is a practical, controllable means for regular delivery of fluoride. Processing of milk is commonly centralised and uses standardised conditions, allowing easy supplementation of fluoride for distribution to communities. The purpose of this study was to resolve the question of availability of fluoride ingested in milk compared with fluoride ingested in water by measuring fluoride deposition in the developing permanent incisors of young sheep. Incisors were analysed using a proton microprobe. (author). 18 refs., 1 tabs., 3 figs

  9. Water Fluoridation: A Critical Review of the Physiological Effects of Ingested Fluoride as a Public Health Intervention

    Directory of Open Access Journals (Sweden)

    Stephen Peckham

    2014-01-01

    Full Text Available Fluorine is the world’s 13th most abundant element and constitutes 0.08% of the Earth crust. It has the highest electronegativity of all elements. Fluoride is widely distributed in the environment, occurring in the air, soils, rocks, and water. Although fluoride is used industrially in a fluorine compound, the manufacture of ceramics, pesticides, aerosol propellants, refrigerants, glassware, and Teflon cookware, it is a generally unwanted byproduct of aluminium, fertilizer, and iron ore manufacture. The medicinal use of fluorides for the prevention of dental caries began in January 1945 when community water supplies in Grand Rapids, United States, were fluoridated to a level of 1 ppm as a dental caries prevention measure. However, water fluoridation remains a controversial public health measure. This paper reviews the human health effects of fluoride. The authors conclude that available evidence suggests that fluoride has a potential to cause major adverse human health problems, while having only a modest dental caries prevention effect. As part of efforts to reduce hazardous fluoride ingestion, the practice of artificial water fluoridation should be reconsidered globally, while industrial safety measures need to be tightened in order to reduce unethical discharge of fluoride compounds into the environment. Public health approaches for global dental caries reduction that do not involve systemic ingestion of fluoride are urgently needed.

  10. Effective use of fluorides for the prevention of dental caries in the 21st century

    DEFF Research Database (Denmark)

    Petersen, Poul Erik; Lennon, Michael A

    2004-01-01

    , due to changing living conditions and dietary habits, and inadequate exposure to fluorides. Research on the oral health effects of fluoride started around 100 years ago; the focus has been on the link between water and fluorides and dental caries and fluorosis, topical fluoride applications, fluoride...

  11. Fluoride content of clay minerals and argillaceous earth materials

    Science.gov (United States)

    Thomas, J., Jr.; Glass, H.D.; White, W.A.; Trandel, R.M.

    1977-01-01

    A reliable method, utilizing a fluoride ion-selective electrode, is described for the determination of fluoride in clays and shales. Interference by aluminum and iron is minimal. The reproducibility of the method is about ??5% at different levels of fluoride concentration. Data are presented for various clay minerals and for the clays and shales. Fluoride values range from 44 ppm (0.0044%) for nontronite from Colfax, WA, to 51,800 ppm (5.18%) for hectorite from Hector, CA. In general, clays formed under hydrothermal conditions are relatively high in fluoride content, provided the hydrothermal waters are high in fluoride content. Besides hectorite, dickite from Ouray, CO, was found to contain more than 50 times as much fluoride (6700 ppm) as highly crystalline geode kaolinite (125 ppm). The clay stratum immediately overlying a fluorite mineralized zone in southern Illinois was found to have a higher fluoride content than the same stratum in a nonmineralized zone approximately 1 mile away. Nonmarine shales in contact with Australian coals were found to be lower in fluoride content than were marine shales in contact with Illinois coals. It is believed that, in certain instances, peak shifts on DTA curves of similar clay minerals are the result of significant differences in their fluoride content. ?? 1977.

  12. Arsenic from community water fluoridation: quantifying the effect.

    Science.gov (United States)

    Peterson, Emily; Shapiro, Howard; Li, Ye; Minnery, John G; Copes, Ray

    2016-04-01

    Community water fluoridation is a WHO recommended strategy to prevent dental carries. One debated concern is that hydrofluorosilicic acid, used to fluoridate water, contains arsenic and poses a health risk. This study was undertaken to determine if fluoridation contributes to arsenic in drinking water, to estimate the amount of additional arsenic associated with fluoridation, and compare this to the National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard and estimates from other researchers. Using surveillance data from Ontario drinking water systems, mixed effects linear regression was performed to examine the effect of fluoridation status on the difference in arsenic concentration between raw water and treated water samples. On average, drinking water treatment was found to reduce arsenic levels in water in both fluoridated and non-fluoridated systems by 0.2 μg/L. However, fluoridated systems were associated with an additional 0.078 μg/L (95% CI 0.021, 0.136) of arsenic in water when compared to non-fluoridated systems (P = 0.008) while controlling for raw water arsenic concentrations, types of treatment processes, and source water type. Our estimate is consistent with concentrations expected from other research and is less than 10% of the NSF/ANSI standard of 1 μg/L arsenic in water. This study provides further information to inform decision-making regarding community water fluoridation.

  13. Caries prevention through the fluoridation of milk. A review.

    Science.gov (United States)

    Bánóczy, Jolán; Rugg-Gunn, Andrew J

    2007-10-01

    The aim of this review is to give an overview of 50 years experience of milk fluoridation and draw conclusions about the applicability of the method. Fluoridated milk was first investigated in the early 1950s, almost simultaneously in Switzerland, the USA and Japan. Stimulated by the favourable results obtained from these early studies, the establishment of The Borrow Dental Milk Foundation (subsequently The Borrow Foundation) in England gave an excellent opportunity for further research, both clinical and non-clinical, and a productive collaboration with the World Health Organization from the early 1980s onwards. Numerous peer-reviewed publications in international journals showed clearly the bioavailability of fluoride in milk, and increased concentrations of fluoride in saliva, dental plaque, dental enamel and dentine, and urine, after consumption of fluoridated milk. Clinical trials were initiated in the 1980s--some of these can be classed as randomised controlled trials, while most of the clinical studies were community preventive programs. These evaluations showed clearly that the optimal daily intake of fluoride in milk is effective in preventing dental caries. At present, milk fluoridation programs are running continuously in about ten countries of the world. Fluoridation of milk can be recommended as a caries preventive measure where the fluoride concentration in drinking water is suboptimal, caries experience in children is significant, and there is an existing school milk program. The program should aim to provide fluoridated milk for at least 200 days per year and should commence before the children are 4 years of age.

  14. Parabens do not increase fluoride uptake by dental enamel

    Directory of Open Access Journals (Sweden)

    Vanessa Silva Tramontino

    2010-04-01

    Full Text Available Objective: To evaluate whether methylparaben and propylparaben, which present a similar chemical structure, increase fluoride uptake by demineralized dental enamel when present in buffered solutions. Methods: The study comprised an in vitro experiment using blocks of bovine dental enamel with artificial carious lesions. Enamel blocks were exposed to the following treatment (n=12: fluoride solution (200 ppm fluoride - control; solution containing fluoride and 13 mM methylparaben; solution containing fluoride and 13 mM propylparaben in 35% propylene glycol; solution containing fluoride in 35% propylene glycol. All solutions were buffered (0.01 M cacodilate and the pH was adjusted to 6.27. The blocks were exposed to the treatment solutions in the proportion of 2 ml per mm2 of exposed enamel area and fluoride formed was estimated after removing an enamel layer by acid etching. Fluoride extracted was determined by ion specific electrode and the amount of enamel removed was estimated by phosphorus analysis. ANOVA followed by Tukey’s test were used for statistical analysis, with significance level at 5%. Results: The dental blocks of treatment groups containing both parabens and the control group presented similar fluoride concentration in enamel and no statistical difference was observed among them (p>0.05. The dental blocks of treatment group containing fluoride and propylene glycol showed the lowest value of fluoride present in enamel, which was significantly different from the control and fluoride and methylparaben groups (p<0.05. Conclusion: Methyl and propylparaben in a buffered solution do not enhance fluoride uptake by demineralized dental enamel.

  15. Analysis of differentially expressed genes between fluoride-sensitive and fluoride-endurable individuals in midgut of silkworm, Bombyx mori.

    Science.gov (United States)

    Qian, Heying; Li, Gang; He, Qingling; Zhang, Huaguang; Xu, Anying

    2016-08-15

    Fluoride tolerance is an economically important trait of silkworm. Near-isogenic lines (NILs) of the dominant endurance to fluoride (Def) gene in Bombyx mori has been constructed before. Here, we analyzed the gene expression profiles of midgut of fluoride-sensitive and fluoride-endurable individuals of Def NILs by using high-throughput Illumina sequencing technology and bioinformatics tools, and identified differentially expressed genes between these individuals. A total of 3,612,399 and 3,567,631 clean tags for the libraries of fluoride-endurable and fluoride-sensitive individuals were obtained, which corresponded to 32,933 and 43,976 distinct clean tags, respectively. Analysis of differentially expressed genes indicates that 241 genes are differentially expressed between the two libraries. Among the 241 genes, 30 are up-regulated and 211 are down-regulated in fluoride-endurable individuals. Pathway enrichment analysis demonstrates that genes related to ribosomes, pancreatic secretion, steroid biosynthesis, glutathione metabolism, steroid biosynthesis, and glycerolipid metabolism are down-regulated in fluoride-endurable individuals. qRT-PCR was conducted to confirm the results of the DGE. The present study analyzed differential expression of related genes and tried to find out whether the crucial genes were related to fluoride detoxification which might elucidate fluoride effect and provide a new way in the fluorosis research. PMID:27106117

  16. Fluoride ion encapsulation by Mg2+ ions and phosphates in a fluoride riboswitch.

    Science.gov (United States)

    Ren, Aiming; Rajashankar, Kanagalaghatta R; Patel, Dinshaw J

    2012-06-01

    Significant advances in our understanding of RNA architecture, folding and recognition have emerged from structure-function studies on riboswitches, non-coding RNAs whose sensing domains bind small ligands and whose adjacent expression platforms contain RNA elements involved in the control of gene regulation. We now report on the ligand-bound structure of the Thermotoga petrophila fluoride riboswitch, which adopts a higher-order RNA architecture stabilized by pseudoknot and long-range reversed Watson-Crick and Hoogsteen A•U pair formation. The bound fluoride ion is encapsulated within the junctional architecture, anchored in place through direct coordination to three Mg(2+) ions, which in turn are octahedrally coordinated to water molecules and five inwardly pointing backbone phosphates. Our structure of the fluoride riboswitch in the bound state shows how RNA can form a binding pocket selective for fluoride, while discriminating against larger halide ions. The T. petrophila fluoride riboswitch probably functions in gene regulation through a transcription termination mechanism. PMID:22678284

  17. Method for decontamination of nickel-fluoride-coated nickel containing actinide-metal fluorides

    Science.gov (United States)

    Windt, Norman F.; Williams, Joe L.

    1983-01-01

    The invention is a process for decontaminating particulate nickel contaminated with actinide-metal fluorides. In one aspect, the invention comprises contacting nickel-fluoride-coated nickel with gaseous ammonia at a temperature effecting nickel-catalyzed dissociation thereof and effecting hydrogen-reduction of the nickel fluoride. The resulting nickel is heated to form a melt and a slag and to effect transfer of actinide metals from the melt into the slag. The melt and slag are then separated. In another aspect, nickel containing nickel oxide and actinide metals is contacted with ammonia at a temperature effecting nickel-catalyzed dissociation to effect conversion of the nickel oxide to the metal. The resulting nickel is then melted and separated as described. In another aspect nickel-fluoride-coated nickel containing actinide-metal fluorides is contacted with both steam and ammonia. The resulting nickel then is melted and separated as described. The invention is characterized by higher nickel recovery, efficient use of ammonia, a substantial decrease in slag formation and fuming, and a valuable increase in the service life of the furnace liners used for melting.

  18. The Effect of Calcium Pre-Rinse on Salivary Fluoride After 900 ppm Fluoride Mouthwash: A Randomized Clinical Trial

    Directory of Open Access Journals (Sweden)

    Nahid Ramazani

    2013-01-01

    Full Text Available Objective: Calcium fluoride deposit during fluoride application. Uptake and retention of fluoride by saliva depends generally on the concentration of calcium. In this study, the ef-fect of calcium pre-rinse on salivary fluoride concentration after a 900 ppm fluoride mouthwash was investigated.Materials and Methods: This cross-over double-blind randomized clinical trial was con-ducted in a girls' dormitory in Zahedan University of Medical Sciences, southeast Iran. In this study, 42 female dental students were chosen using simple randomization. During the first phase, 21 subjects (group A used fluoride rinse (F regimen and the remaining (group B used calcium pre-rinse followed immediately by fluoride rinse (Ca + F regi-men. In the second phase, participants rinsed using the mouthwashes not previously used. Prior to each phase prophylaxis was performed and no fluoridated product was used dur-ing a two-week interval between the phases. Salivary samples were taken immediately be-fore (baseline, 1 and 12 hours after rinsing. The salivary fluoride concentration was de-termined using fluoride sensitive electrode. Repeated measures ANOVA was used for sta-tistical analysis and the significance level was set at P<0.05.Results: There was significant difference between fluoride concentrations at different time points (P< 0.001. Significant differences were observed when the different time points of two regimens were examined. In contrast to this, the baseline before using F regimen and the baseline before using Ca + F regimen did not show any significance (P= 0.070.Conclusion: Pre-rinsing with calcium before fluoride is recommended because of signifi-cant increases in salivary fluoride concentration.

  19. Friction and Wear Properties and Dielectric Properties of Graphene Oxide and Chopped Carbon Fiber Modified Polyvinylidene Fluoride Composite Films%氧化石墨烯、短切碳纤维改性聚偏氟乙烯复合膜的摩擦磨损及介电性能

    Institute of Scientific and Technical Information of China (English)

    韩朋; 井晓静; 沈湘黔; 闵春英; 潘铁政

    2013-01-01

    采用溶液浇铸法分别制备了氧化石墨烯(GO)与短切碳纤维(CF)改性聚偏氟乙烯(PVDF)复合膜;采用摩擦磨损试验机和数字电桥研究了复合膜的摩擦磨损性能及介电性能.结果表明:在GO和CF添加量较低时(体积分数小于1%),复合膜的摩擦因数较低,同时具有时间稳定性;GO和CF添加量较高时,随时间延长,CF/PVDF复合膜的摩擦因数增大,而GO/PVDF复合膜具有时间稳定性;随着GO和CF添加量增多,复合膜的介电常数先升高后下降,介电损耗先下降后升高;随着频率的增大,复合膜的介电常数缓慢下降,而介电损耗先下降后急剧升高.%The graphene oxide (GO), chopped carbon fiber (CF) modified poly( vinylidene fluoride) (PVDF ) composite films were prepared by the solution casting process. The Friction and wear properties of composite films and dielectric property were studied by friction and wear tester and digital electric bridge, respectively. The results show that when GO or CF content was low (<1 vol. %). the friction coefficient of the films decreased and tended to be stable with time. When the content of GO or CF in the films was high, the films showed various behaviors. The friction coefficient for the former increased with time, while the later had an almost stable friction coefficient. With addition of GO or CF increasing, the dielectric constant of the composite films rose and then dropped, whilst the dielectric-loss decreased at first and then increased. And with the frequency increase the dielectric constant had a slow drop,and the dielectric-loss initially rose and then reduced dramatically.

  20. Fluoridation and tooth wear in Irish adults.

    LENUS (Irish Health Repository)

    Burke, F M

    2010-10-01

    The aim of this study was to determine the prevalence of tooth wear in adults in Ireland and its relationship with water fluoridation. The National Survey of Adult Oral Health was conducted in 2000\\/2001. Tooth wear was determined using a partial mouth examination assessing the upper and lower anterior teeth. A total of 2456 subjects were examined. In this survey, increasing levels and severity of tooth wear were associated with ageing. Men were more affected by tooth wear and were more likely to be affected by severe tooth wear than women. It was found that age, and gender were significant predictors of tooth wear (P < 0.01). Overall, there was no significant relationship between fluoridation and tooth wear in this study.

  1. Revisiting the thermochemistry of chlorine fluorides

    CERN Document Server

    Sánchez, H R

    2016-01-01

    In this work, accurate calculations of standard enthalpies of formation of chlorine fluorides (ClF$_n$, n=1--7; Cl$_2$F and Cl$_3$F$_2$) were performed through the isodesmic reactions scheme. It is argued that, for many chlorine fluorides, the gold standard method of quantum chemistry (CCSD(T)) is not capable to predict enthalpy values nearing chemical accuracy if atomization scheme is used. This is underpinned by a thorough analysis of total atomization energy results and the inspection of multireference features of these compounds. Other thermodynamic quantities were also calculated at different temperatures. In order to complement the energetic description, elimination curves were studied through density functional theory as a computationally affordable alternative to highly correlated wave function-based methods.

  2. Fluoride complexation of element 104, rutherfordium.

    Science.gov (United States)

    Haba, Hiromitsu; Tsukada, Kazuaki; Asai, Masato; Toyoshima, Atsushi; Akiyama, Kazuhiko; Nishinaka, Ichiro; Hirata, Masaru; Yaita, Tsuyoshi; Ichikawa, Shin-Ichi; Nagame, Yuichiro; Yasuda, Ken-Ichiro; Miyamoto, Yutaka; Kaneko, Tetsuya; Goto, Shin-Ichi; Ono, Sawako; Hirai, Toshiyuki; Kudo, Hisaaki; Shigekawa, Mitsuru; Shinohara, Atsushi; Oura, Yasuji; Nakahara, Hiromichi; Sueki, Keisuke; Kikunaga, Hidetoshi; Kinoshita, Norikazu; Tsuruga, Naoya; Yokoyama, Akihiko; Sakama, Minoru; Enomoto, Shuich; Schädel, Matthias; Brüchle, Willy; Kratz, Jens V

    2004-04-28

    Fluoride complexation of element 104, rutherfordium (Rf), produced in the 248Cm(18O,5n)261Rf reaction has been studied by anion-exchange chromatography on an atom-at-a-time scale. The anion-exchange chromatographic behavior of Rf was investigated in 1.9-13.9 M hydrofluoric acid together with those of the group-4 elements Zr and Hf produced in the 18O-induced reactions on Ge and Gd targets, respectively. It was found that the adsorption behavior of Rf on anion-exchange resin is quite different from those of Zr and Hf, suggesting the influence of relativistic effects on the fluoride complexation of Rf.

  3. Perspectives in the effective use of fluoride in Asia

    DEFF Research Database (Denmark)

    Petersen, P E; Phantumvanit, P

    2012-01-01

    services, in particular, exposure to disease prevention programs (Petersen, 2003, 2008a). Benefits of fluoride for caries prevention have been substantiated in many countries (Petersen and Lennon, 2004; Jones et al., 2005). In the second half of the 20th century, this focus shifted to the development...... and evaluation of fluoride toothpastes and rinses and, to a lesser extent, to alternatives to water fluoridation, such as salt and milk fluoridation. Most recently, efforts have been made to summarize this extensive database through systematic reviews of fluoride administration (McDonagh et al., 2000; Marinho et...... al., 2003; Australian Government, 2007). The Asian workshop held in Phan-Nga, Thailand, during March 22-24, 2011, aimed to discuss current information on fluoride and dental caries, as well as to try identifying barriers and opportunities that countries of Asia may have for implementing such programs...

  4. Adsorption of Fluoride Ion by Inorganic Cerium Based Adsorbent

    Institute of Scientific and Technical Information of China (English)

    Jiao Zhongzhi(焦中志); Chen Zhonglin; Yang Min; Zhang Yu; Li Guibai

    2004-01-01

    Excess of fluoride in drinking water is harmful to human health, the concentration of F- ions must be maintained in the range of 0.5 to 1.5 mg/L. An inorganic cerium based adsorbent (CTA) is developed on the basis of research of adsorption of fluoride on cerium oxide hydrate. Some adsorption of fluoride by CTA adsorbent experiments were carried out, and results showed that CTA adsorbent has a quick adsorption speed and a large adsorption capacity. Adsorption follows Freundlich isotherm, and low pH value helps fluoride removal. Some physical-chemical characteristics of CTA adsorbent were experimented, fluoride removal mechanism was explored, and results showed that hydroxyl group of CTA adsorbent played an important role in the fluoride removal.

  5. Fluoride contamination in rain water of Sigrauli region

    Energy Technology Data Exchange (ETDEWEB)

    Chaurasia, S.; Mishra, S.K. [Mahatma Gandhi Chitrakoot Gramodaya, Chitrakoot (India)

    2007-07-01

    In this paper fluoride was monitored in rain water during rainy season at seven locations of Sigrauli region in 2004. The sampling location covered the impact of industrial complex of the area, and its impact on surface water sources monitored for the fluoride, pH, and electrical conductivity. The higher concentration of fluoride in rain water was observed 2.03 mg/L at Dudhar and in ponds water highest value was 3.14 mg/L. This suggested that serious fluoride pollution is occurring in Singrauli region posing a threat to the health and livelihood of the people of the region. Fluoride transported by the air route from coal burning emissions of large thermal power plants concentrate in small geographical area, and industries. Fluoride pollution in Singrauli area deserve intensive scientific studies and urgent attention. 2 figs., 2 tabs.

  6. Distribution of fluoride in ground water of West Virginia

    Science.gov (United States)

    Mathes, M.V.; Waldron, M.C.

    1993-01-01

    This report describes the results of a study by the U.S. Geological Survey, in cooperation with the West Virginia Geological and Economic Survey, to evaluate the distribution of fluoride in ground water of West Virginia. Fluoride is a natural chemical constituent in domestic and public water supplies in West Virginia. Fluoride concentrations of about 1.0 milligram per liter in drinking water are beneficial to dental health. Concentrations greater than 2.0 milligrams per liter, however, could harm teeth and bones. Fluoride concentra- tions in ground water of West Virginia range from less than 0.1 to 12 milligrams per liter. Fluoride concentrations that exceed 2.0 milligrams per liter are found in wells drilled to all depths, wells drilled in all topographic settings, and wells drilled into most geologic units. Most fluoride concentrations that exceed 2.0 milligrams per liter are located at sites clustered in the northwestern part of the State.

  7. Viscosity estimation for slags containing calcium fluoride

    Institute of Scientific and Technical Information of China (English)

    Qifeng Shu; Jiayun Zhang

    2005-01-01

    Based on recently published experimental data, the Riboud model was modified for viscosity estimation of the slags containing calcium fluoride. The estimated values were in good agreement with measured data. Reasonable estimation can be achieved using the modified Riboud model for mould fluxes and ESR (eletro slag remelting) slags. Especially for ESR slags, the modified Riboud model can provide much more precise values than the original Riboud model.

  8. Fluoride solid electrolytes containing rare earth elements

    Institute of Scientific and Technical Information of China (English)

    Viera Trnovcová; Pavel P. Fedorov; Ivan Furár

    2008-01-01

    Relations between the structure, ionic conductivity and dielectric properties of fluoride systems of different structures containing rare earth elements were presented. Superionic conductivities, by fluoride ions, of fluorite-structured (MF2-REF3, M=Ba, Pb, RE=La-Lu, Sc, Y), orthorhombic (REF3, RE=Tb-Er,Y), tysonite-structured (REF3-MF2, RE=La-Nd, M=Sr), monoclinic (BaRE2F8, RE=Ho-Yb, Y) fluoride single crystals and eutectic composites (LiF-REF3, RE=La-Gd,Y) were compared. Anisotropy of electrical properties of crystals with a lower symmetry was explained by modeling optimum ionic paths. For explanation of concentration dependences of fast ionic conductivity, models of aggregation of defects into clusters were proposed. In fluorite-structured crystals, the highest ionic conductivity was found for PbF2: 7 mol% ScF3 (at 500 K, σ500=0.13 S/cm). In tysonite-structured crystals, the highest ionic conductivity was found for LaF3: 3 mol% SrF2 (σ500=2.4×10-2 S/cm). Different types of coordination polyhedrons and their different linking in orthorhombic and tysonite structure explained large differences between conductivities in both structures. Eutectic systems, prepared as directionally solidified composites, enabled to study some orthorhombic fluoride phases (GdF3, SmF3), which cannot be prepared as single crystals. An influence of the orthorhombic-tysonite phase transition on the ionic conductivity was shown.

  9. Effect of fluoride toothpastes on enamel demineralization

    Directory of Open Access Journals (Sweden)

    Gintner Zeno

    2006-06-01

    Full Text Available Abstract Background It was the aim of this study to investigate the effect of four different toothpastes with differing fluoride compounds on enamel remineralization. Methods A 3 × 3 mm window on the enamel surface of 90 human premolars was demineralized in a hydroxyethylcellulose solution at pH 4.8. The teeth were divided into 6 groups and the lower half of the window was covered with varnish serving as control. The teeth were immersed in a toothpaste slurry containing: placebo tooth paste (group 1; remineralization solution (group 2; Elmex Anticaries (group 3; Elmex Sensitive (group 4; Blend-a-med Complete (group 5 and Colgate GRF (group 6. Ten teeth of each group were used for the determination of the F- content in the superficial enamel layer and acid solubility of enamel expressed in soluble phosphorus. Of 6 teeth of each group serial sections were cut and investigated with polarization light microscopy (PLM and quantitative energy dispersive X-ray analysis (EDX. Results The PLM results showed an increased remineralization of the lesion body in the Elmex Anticaries, Elmex Sensitive and Colgate GRF group but not in the Blend-a-med group. A statistically significant higher Ca content was found in the Elmex Anticaries group. The fluoride content in the superficial enamel layer was significantly increased in both Elmex groups and the Blend-a-med group. Phosphorus solubility was significantly decreased in both Elmex groups and the Blend-a-med group. Conclusion It can be concluded that amine fluoride compounds in toothpastes result in a clearly marked remineralization of caries like enamel lesions followed by sodium fluoride and sodium monofluorophosphate formulations.

  10. Health protection: Fluoridation and dental health.

    OpenAIRE

    1983-01-01

    Tooth decay, which affects 95 percent of Americans, is our most common health problem, costing an estimated +2 billion yearly for treatment. By the time children reach 17 years of age, 94 percent have experienced caries and 36 percent have lost one or more permanent teeth due to caries. Dental disease prevention embodies the spectrum of many activities from the fluoridation of community and school water supplies to the dental health education of the child and adult. At this stage of our knowl...

  11. Delivery Challenges for Fluoride, Chlorhexidine and Xylitol

    OpenAIRE

    Featherstone, John DB

    2006-01-01

    The progression or reversal of dental caries is determined by the balance between pathological and protective factors. It is well established that a) fluoride inhibits demineralization and enhances remineralization, b) chlorhexidine reduces the cariogenic bacterial challenge, and c) xylitol is non-cariogenic and has antibacterial properties. The challenge that we face is how best to deliver these anti-caries entities at true therapeutic levels, over time, to favorably tip the caries balance. ...

  12. Investigation on poly (vinylidene fluoride) based gel polymer electrolytes

    Indian Academy of Sciences (India)

    S Rajendran; P Sivakumar; Ravi Shanker Babu

    2006-12-01

    An investigation is carried out on gel polymer electrolytes consisting of poly (vinylidene fluoride) (PVdF) as a host polymer, lithium perchlorate (LiClO4), lithium triflate (LiCF3SO3) as salts and mixture of ethylene carbonate (EC) and propylene carbonate (PC) as plasticizers. Polymer thin films were prepared by solvent casting technique and the obtained films were subjected to different characterizations, to confirm their structure, complexation and thermal changes. X-ray diffraction revealed that the salts and plasticizers disrupted the crystalline nature of PVdF based polymer electrolytes and converted them into an amorphous phase. TG/DTA studies showed the thermal stability of the polymer electrolytes. The role of interaction between polymer hosts on conductivity is discussed using the results of a.c. impedance studies. Room temperature (28°C) conductivity of 2.786 × 10-3 Scm-1 was observed in PVdF (24)–EC/PC (68)–LiCF3SO3 (2)/LiClO4 (6) polymer system.

  13. Biological effects data: Fluoride and sulfur dioxide

    Energy Technology Data Exchange (ETDEWEB)

    McMechan, K.J. (ed.); Holton, R.L.; Ulbricht, R.J.; Morgan , J.B.

    1975-04-01

    The Alumax Pacific Aluminum Corporation has proposed construction of an aluminum reduction facility near Youngs Bay at Warrenton, Oregon. This report comprises one part of the final report to Alumax on a research project entitled, Physical, Chemical and Biological Studies of Youngs Bay.'' It presents data pertaining to the potential biological effects of fluoride and sulfur dioxide, two potentially hazardous plant-stack emissions, on selected aquatic species of the area. Companion volumes provide a description of the physical characteristics the geochemistry, and the aquatic animals present in Youngs Bay and adjacent ecosystems. An introductory volume provides general information and maps of the area, and summarizes the conclusions of all four studies. The data from the two phases of the experimental program are included in this report: lethal studies on the effects of selected levels of fluoride and sulfur dioxide on the survival rate of eleven Youngs Bay faunal species from four phyla, and sublethal studies on the effects of fluoride and sulfur dioxide on the rate of primary production of phytoplankton. 44 refs., 18 figs., 38 tabs.

  14. Bone scintigraphy in fluoride treated osteoporosis

    International Nuclear Information System (INIS)

    Quantitative bone scintigraphy was performed on 23 white females with post-menopausal osteoporosis and vertebral compression fractures. These patients were then entered into a randomized, double-blind clinical trial or sodium fluoride therapy (NaF=14, placebo=9) which included repeat bone scintigraphy every six months. Scintigraphic images were acquired for 500K counts per image over the total body with computer acquisition over the posterior thoracic and lumbar spine. Images were obtained on a wide field-of-view gamma camera two hours after injecting 15 mCi of Tc-99m MDP. Data analysis showed a significant reduction in the activity ratio of abnormal vertebral body to normal vertebral body in those patients treated with sodium fluoride (paired t-test p=0.0095). No significant change was observed in the control group of (p=0.142). These results suggest that sodium fluoride therapy promotes more rapid healing of osteoporotic vertebral fractures. They also demonstrate the utility of serial quantitative bone scintigraphy in assessing osteoporotic patients with vertebral compression fractures

  15. How and when to prescribe sodium fluoride.

    Science.gov (United States)

    Shambaugh, G E

    1989-03-01

    Sodium fluoride has now been used for 24 years in an effort to slow down or arrest sensorineural hearing nerve deterioration in patients with stapedial otosclerosis or after stapedectomy, as well as in patients with pure cochlear otosclerosis. Extensive clinical experience in thousands of patients with this therapy has demonstrated its value in arresting previously progressive sensorineural hearing loss. For a long time there were those who objected to this therapy on the basis that it had not been adequately proven by double-blind, placebo-controlled studies. They have been answered by Bretlau's study in Denmark and Fisch's from Switzerland; both investigators confirmed on small groups the value of sodium fluoride by double-blind, placebo-controlled studies. Extensive research by Professor Petrovic of Strasbourg while at our tissue culture laboratory at Northwestern University demonstrated the action of sodium fluoride on bone. A nicely designed study with radioactive strontium by Linthicum, House, and Althaus demonstrated its value in promoting maturation of a spongiotic focus. Today there is no reason to hesitate in prescribing this useful, effective, and safe medication to promote maturation of otospongiotic lesions, and thus to slow down or to arrest progression in sensorineural hearing loss.

  16. Mortality and cancer morbidity after heavy occupational fluoride exposure

    DEFF Research Database (Denmark)

    Grandjean, P; Juel, K; Jensen, Ole Møller

    1985-01-01

    A cohort of 431 male cryolite workers employed for at least six months between 1924 and 1961 was identified from personnel records at the Copenhagen cryolite factory. During this period, heavy fluoride exposure resulted in at least 74 cases of skeletal fluorosis. All workmen in the cohort were......, a possible residual effect of fluoride cannot be excluded. However, any major carcinogenic effect of heavy fluoride exposure would be very unlikely....

  17. 40 CFR 60.202 - Standard for fluorides.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for fluorides. 60.202 Section... Industry: Wet-Process Phosphoric Acid Plants § 60.202 Standard for fluorides. (a) On and after the date on... facility any gases which contain total fluorides in excess of 10.0 g/Mg of equivalent P2O5 feed (0.020...

  18. 40 CFR 60.192 - Standard for fluorides.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for fluorides. 60.192 Section... Plants § 60.192 Standard for fluorides. (a) On and after the date on which the initial performance test... total fluorides, as measured according to § 60.195, in excess of: (1) 1.0 kg/Mg (2.0 lb/ton) of...

  19. The status of community water fluoridation in the United States.

    OpenAIRE

    Easley, M W

    1990-01-01

    Community water fluoridation has served the American public extremely well as the cornerstone of dental caries prevention activities for 45 years. The dental and general health benefits associated with the ingestion of water-borne fluorides have been well known by researchers for an even longer period. Continued research has repeatedly confirmed the safety, effectiveness, and efficiency of community water fluoridation in preventing dental caries for Americans regardless of age, race, ethnicit...

  20. LiFePO_4/C via fluoride doping

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Non-stoichiometric compound fluoride-doped LiFePO4/C cathode materials were synthesized via solid-state reaction using MgF2 and AlF3 as dopant. The fluoride-doped LiFePO4/C samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electrochemical testing. The results show that the materials are well crystallized and fluoride doping cannot change the space structure of LiFePO4. Slight amounts of Fe2O3 with no fluoride impurity were ...

  1. Sodium fluoride influences the expression of keratins in cultured keratinocytes

    OpenAIRE

    Prado, Euridice; Wurtz, Tilmann; Ferbus, Didier; Shabana, El-Hassan; FOREST, Nadine; Berdal, Ariane

    2010-01-01

    Epithelia in lung, skin, and kidney are often exposed to fluoride, and tissue damage in lung and kidney due to fluoride is well documented. Nevertheless, the biological effects of fluoride on epithelia are poorly investigated. In the present study, we report effects of sodium fluoride (NaF) on the differentiation of a human epithelial cell line, HaCaT. These cells may serve as a keratinocyte model, because they express a wide spectrum of keratins (Ks), and they associate into stratified tissu...

  2. Fluoride content in caffeinated, decaffeinated and herbal teas.

    Science.gov (United States)

    Chan, J T; Koh, S H

    1996-01-01

    The fluoride contents of infusions prepared from 44 different brands and types of teas were measured. Fluoride concentrations ranged from 0.34 to 3.71 ppm (mean = 1.50 ppm) in caffeinated tea infusions, 0.02-0.14 ppm (mean = 0.05 ppm) in herbal tea infusions, and 1.01-5.20 ppm (mean = 3.19) in decaffeinated tea infusions. This is the first report of the fluoride content of decaffeinated teas. The mean fluoride content of decaffeinated tea infusions is significantly (p decaffeination is the most likely explanation of the above observation.

  3. Effects of oral doses of fluoride on nestling European starlings

    Science.gov (United States)

    Fleming, W.J.; Grue, C.E.; Schuler, C.A.; Bunck, C.M.

    1987-01-01

    Nestling European starlings (Sturnus vulgaris), raised and fed by free-living adults, were given daily oral doses of either distilled water, 193 mg sodium as Na2CO3 per kg of body weight (sodium control group), or 6, 10, 13, 17,23, 30, 40, 80, 160 mg of the fluoride ion as NaF in distilled water per kg of body weight (mg/kg). Dosing began when nestlings were 24-48 hr old and continued for 16 days. The 24-hr LD50 of fluoride for day-old starlings was 50 mg/kg. The 16-day LD50 was 17 mg/kg. The sodium control group did not differ from the water control group with respect to any of the measured variables. Growth rates were significantly reduced in the 13 and 17 mg of fluoride/kg groups; weights of birds given higher dose levels were omitted from growth comparisons because of high, fluoride-induced mortality. Although pre-fledging weights for the 10, 13, and 17 mg of fluoride/kg groups averaged 3.6 to 8.6% less than controls at 17 days, this difference was not significant. Feather and bone growth of the fluoride and control groups were not different, except for keel length measured at 17 days of age which averaged less in the fluoride groups. Liver and spleen weights were not affected by fluoride treatments. No histological damage related to fluoride treatments was found in liver, spleen, or kidney. The logarithm of bone fluoride and magnesium concentration increased with the logarithm of increasing fluoride treatment levels and were significantly correlated with each other. Fluoride treatments had no effect on percent calcium or phosphorus in bone or plasma alkaline phosphatase activity. Oral doses of fluoride appear to be more toxic than equivalent dietary levels. Most birds probably acquire fluoride through their diet. Therefore, the results of the study may overestimate the potential effects of fluorides on songbirds living in fluoride-contaminated environments.

  4. Oxidative stress in cases of chronic fluoride intoxication

    OpenAIRE

    Ailani, Vinita; R. C. Gupta; Gupta, Sunil Kumar; Gupta, Kapil

    2009-01-01

    This study was conducted to find out the level of oxidative stress and effect of supplementation of vitamin C, D and Calcium on levels of SOD, serum and urinary fluoride in children residing in endemic fluorosis area. For this the fluoride belt of Jaipur district was selected. The parameters selected were Super oxide dismutase, serum fluoride and urinary fluoride. The study was conducted on one hundred children, selected from four areas (25 from each area) consuming water containing 1.2, 2.4,...

  5. Total Fluoride Intake and Urinary Excretion in German Children Aged 3–6 Years

    OpenAIRE

    Haftenberger, Marjolein; Viergutz, Gabriele; Neumeister, Volker; Hetzer, Gisela

    2014-01-01

    There have only been few investigations comparing total fluoride intake and the fluoride proportion excreted in urine in pre–school children. In addition, the results of available studies are conflicting. Total fluoride intake was assessed in 11 healthy children aged 3–6 years on 2 consecutive days and urinary fluoride excretion was determined. The duplicate–diet approach was used for the assessment of fluoride intake from solid and liquid foods. Fluoride intake from toothbrushing was calcula...

  6. Cariostatic effect of fluoride-containing restorative materials associated with fluoride gels on root dentin

    Directory of Open Access Journals (Sweden)

    Fernanda Tavares Borges

    2010-10-01

    Full Text Available Secondary caries is still the main cause of restoration replacement, especially on the root surface OBJECTIVE: This in vitro study evaluated the cariostatic effects of fluoride-containing restorative materials associated with fluoride gels, on root dentin. MATERIALS AND METHODS: A randomized complete block design was used to test the effects of the restorative systems, fluoride regimes and the interactions among them at different distances from restoration margins. Standardized cavities were prepared on 240 bovine root specimens and randomly assigned to 15 groups of treatments (n=16. Cavities were filled with the following restorative materials: Ketac-Fil (3M-ESPE; Vitremer (3M-ESPE; Dyract/Prime & Bond NT (Dentsply; Charisma/Gluma One Bond (Heraeus Kulzer and the control, Z250/Single Bond (3M-ESPE. The specimens were subjected to a pH-cycling model designed to simulate high-caries activity. During the cycles, 1.23% acidulated phosphate fluoride, 2.0% neutral sodium fluoride or deionized/distilled water (control was applied to the specimens for 4 min. The surface Knoop microhardness test was performed before (KHNi and after (KHNf the pH cycles at 100, 200 and 300 mm from the margins. Dentin microhardness loss was represented by the difference in initial and final values (KHNi - KHNf. Data were analyzed by Friedman's and Wilcoxon's tests, ANOVA and Tukey's test (α=5%. RESULTS: The interaction of restorative systems and topical treatments was not significant (p=0.102. Dentin microhardness loss was lowest closer to the restoration. Ketac-fil presented the highest cariostatic effect. Vitremer presented a moderate effect, while Dyract and Charisma did not differ from the control, Z250. The effects of neutral and acidulated fluoride gels were similar to each other and higher than the control. CONCLUSION: Conventional and resin-modified glass ionomer cements as well as neutral and acidulated fluoride gels inhibit the progression of artificial caries

  7. Determination of Fluoride in Toothpaste Using an Ion-Selective Electrode

    Science.gov (United States)

    Light, Truman S.; Cappuccino, Carleton C.

    1975-01-01

    Outlines the theory of chemical potentiometry, describes the experimental procedure for free fluoride determination, and presents sample data of fluoride concentration for various brands of toothpaste. (GS)

  8. PREPARATION AND CHARACTERIZATION OF STRONTIUM FLUORIDE POWDERS ACTIVATED BY NEODYMIUM FLUORIDE

    Directory of Open Access Journals (Sweden)

    S. V. Kuznetsov

    2015-07-01

    Full Text Available Subject of Study. The paper deals with preparation processes of ultradisperse, homogeneous powder Sr1-хNdхF2+х (х= 0.003-0.2, with use of ammonium fluoride as the fluorinating agent taken over 114-120 % from stoichiometry. Method. Nitrate of strontium, neodymium nitrate hexahydrate, with the content equal to 99. 99 % of the basic substance and ammonium fluoride were used as the source of substances. Activated powders of strontium fluoride were obtained by the method of deposition from aqueous solutions by washing the precipitate with a solution of ammonium fluoride, taken over 114 - 120% from stoichiometry. The washed precipitate was centrifuged for 5-7 min, dried in the air at 30-350 C. Heat treatment of the dried precipitate was carried out in two stages: the first stage at the temperature of 200- 2500 C for 0.5-1 hour, the second one at 550- 6000 C for 2-3 hours. X-ray analysis of the synthesized samples was carried out on a Bruker D8 Advance diffractometer, radiation Cu K. The size and shape measuring of the particles of activated strontium fluoride was carried out by means of electron microscope Carl Zeiss NVision 40. The content of neodymium in activated powders of strontium fluoride was determined by the method of spectral emission analysis on the device LEA - S500. Chemical analysis for determination of ammonium ion (NH4+ content in the obtained samples was performed by the method of Kjeldahl. Calculations of lattice parameters, size of coherent scattering regions and the values of micro-deformations were carried out by TOPAS program. Main Results. Preparation processes of ultradisperse, homogeneous powder Sr1-хNdхF2+х (х= 0.003-0.2, with use of ammonium fluoride as the fluorinating agent taken over 114-120 % from stoichiometry, provides obtaining the firm solution Sr1-x-yNdx(NH4yF2+x-y of the cubic fluorite structure. It has been found out that the morphology and size of the resulting product depend on the quantity of

  9. Integrated physicochemical and biological treatment process for fluoride and phosphorus removal from fertilizer plant wastewater.

    Science.gov (United States)

    Gouider, Mbarka; Mlaik, Najwa; Feki, Mongi; Sayadi, Sami

    2011-08-01

    The phosphate fertilizer industry produces highly hazardous and acidic wastewaters. This study was undertaken to develop an integrated approach for the treatment of wastewaters from the phosphate industry. Effluent samples were collected from a local phosphate fertilizer producer and were characterized by their high fluoride and phosphate content. First, the samples were pretreated by precipitation of phosphate and fluoride ions using hydrated lime. The resulting low- fluoride and phosphorus effluent was then treated with the enhanced biological phosphorus removal (EBPR) process to monitor the simultaneous removal of carbon, nitrogen, and phosphorus. Phosphorus removal included a two-stage anaerobic/aerobic system operating under continuous flow. Pretreated wastewater was added to the activated sludge and operated for 160 days in the reactor. The operating strategy included increasing the organic loading rate (OLR) from 0.3 to 1.2 g chemical oxygen demand (COD)/L.d. The stable and high removal rates of COD, NH4(+)-N, and PO4(3-)-P were then recorded. The mean concentrations of the influent were approximately 3600 mg COD/L, 60 mg N/L, and 14 mg P/L, which corresponded to removal efficiencies of approximately 98%, 86%, and 92%, respectively. PMID:21905410

  10. Scientific Opinion on Dietary Reference Values for fluoride

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Dietetic Products, Nutrition and Allergies (NDA

    2013-08-01

    Full Text Available Following a request from the European Commission, the Panel on Dietetic Products, Nutrition and Allergies (NDA derived Dietary Reference Values (DRVs for fluoride, which are provided as Adequate Intake (AI from all sources, including non-dietary sources. Fluoride is not an essential nutrient. Therefore, no Average Requirement for the performance of essential physiological functions can be defined. Nevertheless, the Panel considered that the setting of an AI is appropriate because of the beneficial effects of dietary fluoride on prevention of dental caries. The AI is based on epidemiological studies (performed before the 1970s showing an inverse relationship between the fluoride concentration of water and caries prevalence. As the basis for defining the AI, estimates of mean fluoride intakes of children via diet and drinking water with fluoride concentrations at which the caries preventive effect approached its maximum whilst the risk of dental fluorosis approached its minimum were chosen. Except for one confirmatory longitudinal study in US children, more recent studies were not taken into account as they did not provide information on total dietary fluoride intake, were potentially confounded by the use of fluoride-containing dental hygiene products, and did not permit a conclusion to be drawn on a dose-response relationship between fluoride intake and caries risk. The AI of fluoride from all sources (including non-dietary sources is 0.05 mg/kg body weight per day for both children and adults, including pregnant and lactating women. For pregnant and lactating women, the AI is based on the body weight before pregnancy and lactation. Reliable and representative data on the total fluoride intake of the European population are not available.

  11. Irradiation effects on microhardness of fluoridated and non-fluoridated bovine dentin

    International Nuclear Information System (INIS)

    The objective of this study was to evaluate the effects of irradiation on microhardness of dentin. Dentin blocks from the cervical region of bovine incisors were treated as follows: 1) no irradiation; 2) irradiation of specimens up to 60 Gy (2Gy/day, 5 days/week); 3) no irradiation, but fluoridation of specimens for 5 min/d; 4) irradiation of specimens and daily fluoridation. Knoop hardness number (KHN) of the control specimens was 62.63±14.75 (mean±SD). This was significantly different from the irradiated dentin samples (8.74±2.59 KHN). Hardness of the fluoridated dentin specimens was 11.19±1.95 KHN in the non-irradiated group and 10.03±2.75 KHN in the irradiated groups, respectively. Within the limitations of an in vitro study, it is concluded that dentin is severely affected by irradiation. This could be an explanation for the frequently observed side-effects of irradiation like loss of enamel, gap formation at the amelodentinal junction, and caries of the cervical region. Fluoridation with acidic gels decereases microhardness of dentin surface, and does not prevent softening due to radiation, when saliva is absent. (au)

  12. Synthesis and characterization of ruthenium fluorides and oxide fluorides with high oxidation states

    International Nuclear Information System (INIS)

    The synthesis of ruthenium fluorides and oxide fluorides with high oxidation states was attempted from dioxide RuO2 and tetroxide RuO4. Three fluorinating agents were used: fluorine, chlorine trifluoride and krypton difluoride. The reactions were achieved in anhydrous hydrogen fluoride at room temperature. Thus, the reaction of RuO4 with CIF3 enabled us to prepare chloryl hexafluororuthenate (V), CIO2+ RuF6-, a new compound well identified by vibrational spectroscopy (infra-red and Raman), the structure of which was determined. The reaction of KrF2 with RuO4 gave the oxide tetrafluoride RuOF4, the previously published syntheses and properties of which were not in agreement with each other. This compound was definitely characterized here by chemical analysis, infra-red spectroscopy and X-ray powder diffraction. The product of thermal decomposition (700C) of RuOF4 is presumably RuF4 since only oxygen is liberated during this decomposition. At last, the reaction of KrF2 with RuO2 probably leads to the formation of the new oxide fluoride RuO2F4. Indeed, no oxygen is given off during this reaction, the chemical analysis of the red-orange coloured solid residue is almost in agreement with the one proposed and its infra-red absorption spectrum indicates the presence of ruthenium-oxygen and ruthenium-terminal and bridging fluorine bonds

  13. CAN FLUORIDATION AFFECT LEAD (II) IN POTABLE WATER? HEXAFLUOROSILICATE AND FLUORIDE EQUILIBRIA IN AQUEOUS SOLUTION

    Science.gov (United States)

    Recent reports have attempted to show that fluoridating potable water is linked to increased levels of lead(II) in the blood. We examine these claims in light of the established science and critically evaluate their significance. The completeness of hexafluorosilicate hydrolysi...

  14. Effects of alternating periods of high- and low- fluoride ingestion on dairy cattle

    Energy Technology Data Exchange (ETDEWEB)

    Suttie, J.W.; Carlson, J.R.; Faltin, E.C.

    1972-01-01

    Two- and five-month old Holstein heifers were exposed to different intake patterns of dietary fluoride for 6 years. None of the fluoride treatments affected growth rate or reproduction. There was no consistent effect on milk production. Plasma fluoride concentrations closely followed current fluoride intake. Urinary fluoride concentrations varied with intake but remained elevated during low intake. Skeletal fluoride retention was directly related to total fluoride intake and not to pattern of intake. The degree of dental fluorosis was related to the amount of fluoride fed and to the plasma fluoride concentration at the time each incisor was developing. The most severe effects of fluoride ingestion were in high and low intake. These animals had severly worn molar teeth, extensive osteofluorosis, and they experienced periods of extreme lameness. Short periods of high fluoride intake balanced by periods of lower intake were more damaging to cattle than constant exposure to the same average yearly intake.

  15. Computational investigation of the role of fluoride in Tamao oxidations

    DEFF Research Database (Denmark)

    Mader, Mary M.; Norrby, Per-Ola

    2002-01-01

    The Tamao oxidation of alkoxysilanes was investigated computationally to determine the role of fluoride. a key additive. in this reaction. A sequence of fluoride equilibria as well as possible transition states. mediated by basic and neutral peroxide, respectively, were examined, and a potential...

  16. Methods of controlling hydrogen fluoride pressure during chemical fabrication processes

    Science.gov (United States)

    Solovyov, Vyacheslav; Wiesmann, Harold

    2009-11-24

    The present invention is a method for producing a crystalline end-product. The method comprising exposing a fluoride-containing precursor to a hydrogen fluoride absorber under conditions suitable for the conversion of the precursor into the crystalline end-product.

  17. 7 CFR 305.8 - Sulfuryl fluoride treatment schedules.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 5 2010-01-01 2010-01-01 false Sulfuryl fluoride treatment schedules. 305.8 Section 305.8 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH... fluoride treatment schedules. Treatment schedule Pressure Temperature ( °F) Dosage rate(lb/1000 cubic...

  18. Fluoride uptake from restorative dental materials by human enamel

    International Nuclear Information System (INIS)

    The purpose of the study was to determine the uptake in vitro of fluoride from restorative materials by tooth enamel and whether prior etching of the enamel causes a change of uptake. The outermost layer of the labial surface of extracted canines was removed by grinding and the enamel was covered with five different fluoride-containing materials ; a silicate, a composite resin, an amalgam, a silicophosphate, and a polycarboxylate luting cement. The material was either removed immediately or after storing the tooth in distilled water. The fluoride content was determined using a sensitive physical method based on the 19F (p, αγ) 16O reaction. In addition, the fluoride content of enamel after etching for different periods of time and of etched enamel which had been in contact with silicate cement was determined. The mean fluoride content of uncovered interior enamel was 226 parts 106. All materials, except the composite, increased clearly the fluoride content of the underlying enamel. Etching of interior enamel also increased the fluoride values. No difference could be shown in fluoride uptake from silicate and composite resin between etched and unetched enamel. (author)

  19. KINETICS OF SORPTION OF FLUORIDE ON CALCINED MAGNESITE IN BATCH

    DEFF Research Database (Denmark)

    Singano, J. J.; Mashauri, D. A.; Mtalo, F. W.;

    1997-01-01

    A series of sorption of fluoride on calcined magnesite are obtained from thermostatic pH-chemostat and jar test experiments. The fluoride removal is observed not to start instantly, as normal, but after a lag time of up to ½ an hour of contact time. A model for sorption kinetics is developed, bas...

  20. Fluoride release by glass ionomer cements, compomer and giomer

    Directory of Open Access Journals (Sweden)

    Sayed Mostafa Mousavinasab

    2009-01-01

    Conclusion:Fuji IX, Fuji VII, Fuji IX Extra, and Fuji II LC released higher amounts of fluoride compared to Beautifil and Dyract Extra in this study. It seems that the extent of the glass ionomer matrix plays an important role in determining the fluoride releasing ability of glass ionomer cement materials.

  1. Fluoride Analysis. Training Module 5.200.2.77.

    Science.gov (United States)

    Kirkwood Community Coll., Cedar Rapids, IA.

    This document is an instructional module package prepared in objective form for use by an instructor familiar with fluoride analysis procedures. Included are objectives, an instructor guide, student handouts, and a list of reference material. This module considers the determination of fluoride in water supplies using the SPANDS and electrode…

  2. Obstacles to extending fluoridation in the United States.

    Science.gov (United States)

    Neenan, M E

    1996-09-01

    The purpose of this paper is two-fold: (1) to describe the current extent of water fluoridation in the United States; (2) to address the major obstacles to attaining 75 per cent fluoridation by the year 2000. While 62.1 per cent of the US population has access to fluoridated public water systems, more than 32 million people need to be added to the fluoridation census, primarily from the cities. The legal framework for implementing fluoridation is considered at the state level; a review of fluoridation actions at the local level is presented. The impact of forces affecting the extension of fluoridation in the United States is described: (1) demographic trends--urbanisation, race, ethnicity, language, immigration, age, education levels, housing, income and poverty levels; (2) external environmental forces/political climate; (3) media influence on public opinion and public policy; (4) voter apathy/lack of awareness of the benefits of fluoridation; (5) perceptions of risks vs. benefits; (6) lack of political campaign skills; and (7) legal issues.

  3. Mechanisms of action of fluoride for caries control

    NARCIS (Netherlands)

    M.A.R. Buzalaf; J.P. Pessan; H.M. Honório; J.M. ten Cate

    2011-01-01

    Fluoride was introduced into dentistry over 70 years ago, and it is now recognized as the main factor responsible for the dramatic decline in caries prevalence that has been observed worldwide. However, excessive fluoride intake during the period of tooth development can cause dental fluorosis. In o

  4. Poisoning by coal smoke containing arsenic and fluoride

    Energy Technology Data Exchange (ETDEWEB)

    An, D.; He, Y.G.; Hu, Q.X. [Guizhou Sanitary and Epidemiological Station, Guiyang (China)

    1997-02-01

    An investigation was made into a disease involving skin pigmentation, keratosis of the hands and feet, dental discoloration, and generalized bone and joint pain, stiffness and rigidity, in the village of Bazhi, Zhijin County, Ghizhou Province, People`s Republic of China. Measurements were made of the arsenic and fluoride levels of coal, water, air, food, urine and hair in Bazhi and a control village, Xinzhai, in which coal with a low arsenic content was used. Up to 188 people, including children, in Bazhi and 752 in Xinzhai, were examined for the presence of chronic arsenium, skeletal fluorosis, dental fluorosis and electrocardiogram abnormalities. The coal in Bazhi was found to contain high levels of arsenic and fluoride resulting, after burning in homes without an adequate chimney systems, in pollution of air and food with arsenic and fluoride. The coal in Xinzhai did not cause arsenic pollution but did produce a higher level of fluoride pollution. It was concluded that the endemic disease in Bazhi was caused by pollution by coal smoke containing arsenic and fluoride. It is suggested that arsenic may act synergistically with fluoride so that a lower level of fluoride may produce fluoride toxicity with dental and skeletal fluorosis.

  5. Fluoride inhibits the response of bone cells to mechanical loading

    NARCIS (Netherlands)

    H.M.E. Willems; E.G.H.M. van den Heuvel; S. Castelein; J. Keverling Buisman; A.L.J.J. Bronckers; A.D. Bakker; J. Klein-Nulend

    2011-01-01

    The response of bone cells to mechanical loading is mediated by the cytoskeleton. Since the bone anabolic agent fluoride disrupts the cytoskeleton, we investigated whether fluoride affects the response of bone cells to mechanical loading, and whether this is cytoskeleton mediated. The mechano-respon

  6. Vacuum Ultraviolet Field Emission Lamp Consisting of Neodymium Ion Doped Lutetium Fluoride Thin Film as Phosphor

    OpenAIRE

    Masahiro Yanagihara; Takayuki Tsuji; Mohd Zamri Yusop; Masaki Tanemura; Shingo Ono; Tomohito Nagami; Kentaro Fukuda; Toshihisa Suyama; Yuui Yokota; Takayuki Yanagida; Akira Yoshikawa

    2014-01-01

    A vacuum ultraviolet (VUV) field emission lamp was developed by using a neodymium ion doped lutetium fluoride (Nd3+ : LuF3) thin film as solid-state phosphor and carbon nanofiber field electron emitters. The thin film was synthesized by pulsed laser deposition and incorporated into the lamp. The cathodoluminescence spectra of the lamp showed multiple emission peaks at 180, 225, and 255 nm. These emission spectra were in good agreement with the spectra reported for the Nd3+ : LuF3 crystal. Mor...

  7. Quantitative Structure-Activity Relationships in the Lithium and Sodium Affinities of n-Alkyl Fluorides

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    B3LYP/6-31+g (d, p) method was used to calculate the lithium and sodium affinities of n-alkyl fluoride. These affinities were found to obey the Holmes relationship, i.e. they correlate linearly with the quotient n/(n+1), where n is the number of carbon atoms in the alkyl chain. From the correlation the limiting values of lithium and sodium affinities for very long alkyl chain were predicted to be -153.3 kJ/mol and -108.4 kJ/mol, respectively.

  8. The status of community water fluoridation in the United States.

    Science.gov (United States)

    Easley, M W

    1990-01-01

    Community water fluoridation has served the American public extremely well as the cornerstone of dental caries prevention activities for 45 years. The dental and general health benefits associated with the ingestion of water-borne fluorides have been well known by researchers for an even longer period. Continued research has repeatedly confirmed the safety, effectiveness, and efficiency of community water fluoridation in preventing dental caries for Americans regardless of age, race, ethnicity, religion, educational status, or socioeconomic level. Despite the obvious benefits associated with this proven public health measure, slow progress has been made toward achieving the 1990 national fluoridation objectives as listed in "Promoting Health/Preventing Disease: Objectives for the Nation." This paper documents the lagging pace of community fluoridation by reviewing and analyzing data reported in "Fluoridation Census, 1985," a document published in late 1988 by the Public Health Service's Centers for Disease Control. Failure to attain the 1990 objectives is attributable to a combination of circumstances, including their low priority within many local, State, and Federal health agencies, inadequate funding at all levels of government, lack of a coordinated and focused national fluoridation effort, failure of most States to require fluoridation, lack of Federal legislation mandating fluoridation, general apathy of most health professional organizations toward fluoridation, misconceptions by the public about effectiveness and safety and, finally, unrelenting opposition by a highly vocal minority of the lay public. In addition, fluoridation successes have not been consistent among States, with wide variation in accomplishments documented in the reported data.While fluoridation still is one of the most cost effective public health measures available to local,State, and Federal public health agencies, it remains significantly underused nearly a half century after its

  9. LUMINESCENCE IN POTENTIAL FLUORIDE GLASS LASERS

    OpenAIRE

    Jørgensen, C.

    1987-01-01

    Fluoride glasses of the zirconium barium lanthanide type (invented Rennes, 1975) and lead gallium zinc (or manganese) type (invented Le Mans, 1979) show luminescence of lanthanide J-Levels situated at least 2000 cm-1 above the closest lower level (this limit is a few times larger in most other materials). Not only is the non-radiative de-excitation as weak as incrystalline LaF3 (studied by Weber) but energy transfer between neodymium and ytterbium (III), or from manganese (II), and to some ex...

  10. Electrorecovery of tantalum in molten fluorides

    International Nuclear Information System (INIS)

    Considering the privileged situation of Brazil as a productor of tantaliferous minerals, the authors have in view the development of a technology for production of metallic tantalum via molten salts electrolysis; this has the advantage of improving the aggregate value of exportation products, additionally to tantalum oxide and tantalum concentrates. Having in view the preliminary determintion of better conditions of temperature, electrolyte composition and current density for this process, electrolysis were conducted with a solvent composed of an eutetic mixture of lithium, sodium and potassium fluoride for dipotassium fluotantalate and occasionally for tantalum oxide. Current efficiencies as high as 83% were obtained in favoured conditions. (author)

  11. Fluoride microresonators for mid-IR applications

    CERN Document Server

    Grudinin, Ivan S; Yu, Nan

    2016-01-01

    We study crystalline fluoride microresonators for mid-infrared applications. Whispering gallery mode resonators were fabricated with BaF$_2$, CaF$_2$ and MgF$_2$ crystals. The quality factors were measured at wavelengths of 1.56 {\\mu}m and 4.58 {\\mu}m. The impacts of fabrication technique, impurities, multiphonon absorption and surface water are investigated. It is found that MgF2 resonators have room temperature Q factor of $8.3\\times 10^6$ at wavelength of 4.58 {\\mu}m, limited by multiphonon absorption.

  12. Caries prevention with fluoride toothpaste in children: an update

    DEFF Research Database (Denmark)

    Twetman, S

    2009-01-01

    AIM: The aim was to examine recent literature and review the caries-preventive effect of fluoride toothpaste in children. METHODS: Based on three comprehensive systematic reviews published in 2003, a broad search of the PubMed and Cochrane library databases was conducted for papers published 2002......-2008 using "fluoride toothpaste", "fluoride dentifrice" and "fluoride dental cream" as index terms. Relevant publications were identified after assessment of their abstracts. Papers were selected if they reported a prospective controlled design with caries data reported at baseline and at the end...... of the study. The targeted papers were critically assessed concerning design, methodology and performance according to a pre-determined checklist. RESULTS: The initial search revealed 179 papers of which 15 met the inclusion criteria. There was strong evidence that daily use of fluoride toothpaste has...

  13. Fluoride use in Controlling Dental Caries and Fluorosis

    Directory of Open Access Journals (Sweden)

    Gaurav Solanki

    2012-07-01

    Full Text Available Policy were introduced to control fluoride exposure and to reduce the prevalence of fluorosis. The study aimed of describing the prevalence, severity and risk factors for fluorosis, and to describe the trend of fluorosis among Indian children. The study also aimed of exploring the effect of the change in fluoride exposure on dental fluorosis and caries. Establishing an appropriate use of fluoride toothpaste could be successful in reducing fluorosis without a significant increase in caries experience. The use of fluorides for oral health has always involved a balance between the protective benefit against dental caries and the risk of developing fluorosis. The link between fluoride and dental health was established to determining the causes of dental fluorosis or enamel mottling. Fluorosis in Indian children was highly prevalent in the early 1990s.

  14. Assessment of groundwater quality with respect to fluoride.

    Science.gov (United States)

    Salve, P R; Maurya, A; Kumbhare, P S; Ramteke, D S; Wate, S R

    2008-09-01

    The study was conducted in the summer season (April-May 2007). The fluoride concentration along with physico-chemical parameters in ground water samples was determined in various villages of Kadi tehsil at Mehsana district of Gujarat state (India), since in most of the villages it is the only source of drinking water. The fluoride concentrations in these villages varied from 0.94 to 2.81 mg/L (1.37+/-0.56) with highest fluoride level at Visalpur (2.08 mg/L) and lowest at Adaraj (0.91 mg/L). There was found a positive correlation of pH with fluoride and a negative relationship of fluoride with bicarbonate which is generally observed in deep ground water.

  15. Milk fluoridation for the prevention of dental caries

    Directory of Open Access Journals (Sweden)

    Jolán Bánóczy

    2013-11-01

    Full Text Available The aim of this review is to give an overview of 55 years experience of milk fluoridation and draw conclusions about the applicability of the method. Fluoridated milk was first investigated in the early 1950s, almost simultaneously in Switzerland, the USA and Japan. Stimulated by the favourable results obtained from these early studies, the establishment of The Borrow Dental Milk Foundation (subsequently The Borrow Foundation in England gave an excellent opportunity for further research, both clinical and non-clinical, and a productive collaboration with the World Health Organization which began in the early 1980s. Numerous peer-reviewed publications in international journals showed clearly the bioavailability of fluoride in various types of milk. Clinical trials were initiated in the 1980s – some of these can be classed as randomised controlled trials, while most of the clinical studies were community preventive programmes. Conclusion. These evaluations showed clearly that the optimal daily intake of fluoride in milk is effective in preventing dental caries. The amount of fluoride added to milk depends on background fluoride exposure and age of the children: commonly in the range 0.5 to 1.0 mg per day. An advantage of the method is that a precise amount of fluoride can be delivered under controlled conditions. The cost of milk fluoridation programmes is low, about € 2 to 3 per child per year. Fluoridation of milk can be recommended as a caries preventive measure where the fluoride concentration in drinking water is suboptimal, caries experience in children is significant, and there is an existing school milk programme.

  16. Caries prevention through the fluoridation of milk. A review.

    Science.gov (United States)

    Bánóczy, Jolán; Rugg-Gunn, Andrew J

    2007-10-01

    The aim of this review is to give an overview of 50 years experience of milk fluoridation and draw conclusions about the applicability of the method. Fluoridated milk was first investigated in the early 1950s, almost simultaneously in Switzerland, the USA and Japan. Stimulated by the favourable results obtained from these early studies, the establishment of The Borrow Dental Milk Foundation (subsequently The Borrow Foundation) in England gave an excellent opportunity for further research, both clinical and non-clinical, and a productive collaboration with the World Health Organization from the early 1980s onwards. Numerous peer-reviewed publications in international journals showed clearly the bioavailability of fluoride in milk, and increased concentrations of fluoride in saliva, dental plaque, dental enamel and dentine, and urine, after consumption of fluoridated milk. Clinical trials were initiated in the 1980s--some of these can be classed as randomised controlled trials, while most of the clinical studies were community preventive programs. These evaluations showed clearly that the optimal daily intake of fluoride in milk is effective in preventing dental caries. At present, milk fluoridation programs are running continuously in about ten countries of the world. Fluoridation of milk can be recommended as a caries preventive measure where the fluoride concentration in drinking water is suboptimal, caries experience in children is significant, and there is an existing school milk program. The program should aim to provide fluoridated milk for at least 200 days per year and should commence before the children are 4 years of age. PMID:18078140

  17. Fluoride caused thyroid endocrine disruption in male zebrafish (Danio rerio).

    Science.gov (United States)

    Jianjie, Chen; Wenjuan, Xue; Jinling, Cao; Jie, Song; Ruhui, Jia; Meiyan, Li

    2016-02-01

    Excessive fluoride in natural water ecosystem has the potential to detrimentally affect thyroid endocrine system, but little is known of such effects or underlying mechanisms in fish. In the present study, we evaluated the effects of fluoride on growth performance, thyroid histopathology, thyroid hormone levels, and gene expressions in the HPT axis in male zebrafish (Danio rerio) exposed to different determined concentrations of 0.1, 0.9, 2.0 and 4.1 M of fluoride to investigate the effects of fluoride on thyroid endocrine system and the potential toxic mechanisms caused by fluoride. The results indicated that the growth of the male zebrafish used in the experiments was significantly inhibited, the thyroid microtrastructure was changed, and the levels of T3 and T4 were disturbed in fluoride-exposed male fish. In addition, the expressional profiles of genes in HPT axis displayed alteration. The expressions of all studied genes were significantly increased in all fluoride-exposed male fish after exposure for 45 days. The transcriptional levels of corticotrophin-releasing hormone (CRH), thyroid-stimulating hormone (TSH), thyroglobulin (TG), sodium iodide symporter (NIS), iodothyronine I (DIO1), and thyroid hormone receptor alpha (TRα) were also elevated in all fluoride-exposed male fish after 90 days of exposure, while the inconsistent expressions were found in the mRNA of iodothyronineⅡ (DIO2), UDP glucuronosyltransferase 1 family a, b (UGT1ab), transthyretin (TTR), and thyroid hormone receptor beta (TRβ). These results demonstrated that fluoride could notably inhibit the growth of zebrafish, and significantly affect thyroid endocrine system by changing the microtrastructure of thyroid, altering thyroid hormone levels and endocrine-related gene expressions in male zebrafish. All above indicated that fluoride could pose a great threat to thyroid endocrine system, thus detrimentally affected the normal function of thyroid of male zebrafish.

  18. 76 FR 37129 - Determination That SODIUM FLUORIDE F 18 (Sodium Fluoride F-18) Injection, 10 to 200 Millicuries...

    Science.gov (United States)

    2011-06-24

    ... Product List'' section of the Orange Book. In previous instances (see, e.g., 72 FR 9763, March 5, 2007; 61 FR 25497, May 21, 1996), the Agency has determined that, for purposes of Sec. Sec. 314.161 and 314... HUMAN SERVICES Food and Drug Administration Determination That SODIUM FLUORIDE F 18 (Sodium Fluoride...

  19. The comparison of calculated transition probabilities with luminescence characteristics of erbium(III) in fluoride glasses and in the mixed yttrium-zirconium oxide crystal

    Science.gov (United States)

    Reisfeld, R.; Katz, G.; Jacoboni, C.; De Pape, R.; Drexhage, M. G.; Brown, R. N.; Jørgensen, C. K.

    1983-07-01

    Fluorozirconate glasses containing 2 mole% ErF 3 were prepared by melting the binary fluorides with ammonium bifluoride under an atmosphere of carbon tetrachloride and argon at 850°C. Absorption spectra of these glasses were obtained and the Judd-Ofelt parameters were calculated. Emission spectra and lifetimes of erbium in fluorozirconate glass, in lead-gallium-zinc fluoride glass, and in yttrium-zirconium oxide crystal were measured and compared with the theoretical calculations. Laser emission lines in these materials are deduced from these measurements. It is suggested that materials doped with erbium may serve as light sources for fiber optic waveguides made from the undoped materials.

  20. Photomediated Controlled Radical Polymerization and Block Copolymerization of Vinylidene Fluoride.

    Science.gov (United States)

    Asandei, Alexandru D

    2016-02-24

    This review summarizes recent research on novel photochemical methods for the initiation and control of the polymerization of main chain fluorinated monomers as exemplified by vinylidene fluoride (VDF) and for the synthesis of their block copolymers. Such reactions can be carried out at ambient temperature in glass tubes using visible light. Novel, original protocols include the use of hypervalent iodide carboxylates alone or in conjunction with molecular iodine, as well as the use of photoactive transition metal carbonyls in the presence of alkyl, fluoroalkyl, and perfluoroalkyl halides. An in-depth study of the reaction parameters highlights the use of dimethyl carbonate as a preferred polymerization solvent and outlines the structure-property relationship for hypervalent iodide carboxylates and halide initiators in both the free radical and iodine degenerative transfer controlled radical polymerization (IDT-CRP) of VDF. Finally, the rational selection of metal carbonyls that are successful not only as IDT mediators but, more importantly, in the quantitative activation of both PVDF-CH2-CF2-I and PVDF-CF2-CH2-I chain ends toward the synthesis of well-defined PVDF block copolymers is presented. PMID:26760676

  1. Luminescence in potential fluoride glass lasers

    International Nuclear Information System (INIS)

    Fluoride glasses of the zirconium barium lanthanide type (invented Rennes, 1975) and lead gallium zinc (or manganese) type (invented Le Mans, 1979) show luminescence of lanthanide J-Levels situated at least 2000 cm-1 above the closest lower level (this limit is a few times larger in most other materials). Not only is the non-radiative de-excitation as weaK as in crystalline LaF3 (studied by Weber) but energy transfer between neodymium and ytterbium(III), or from manganese(II), and to some extent from chromium(III), to luminescent J-levels of neodymium(III), erbium(III) and thullium(III) is highly efficient even at low concentrations. One advantage for laser applications is that the lowest quartet state of manganese(II) has a life-time 10 to 15 milliseconds (like in many phosphate glasses and crystalline compounds) allowing energy transfer, extending by huge factors the average life-time of the emitting J-levels. Though the tera-watt lasers (Livermore, California, 1978) inducing deuterium-tritium fusion are silicate glass containing neodymium(III), fluoride glasses should be preferable for many purposes. The evaluation of laser parameters from small-scale experimentation is feasible

  2. Polyvinylidene fluoride - a polymer as transducer material

    International Nuclear Information System (INIS)

    Polyvinylidene fluoride or PVDF is a flexible, thin piezo film and long chain semicrystalline polymer containing repeated of CH/sub 2/ - CH/sub 2/. In order to obtain desired piezoelectric properties PVDF is poled by subjecting it to high electric field. In poled PVDF piezoelectric constants have different values for each axis and one constant per axis. PVDF polymer exhibits generator and motor action. Usually 1000 A /sup o/ thick vacuum-deposited aluminum electrodes are formed on both sides of the sheet. Polymer material of PVDF can be used as a sensing element with temperature range of -40 /sup 0/ C to 100 /sup 0/C and a frequency range of 10/sup -3/ to 10/sup -9/ Hz. This paper includes as experimental observation of exciting aluminium open-ended tube at its resonance using PVDF transducer and maintained in this condition using phase lock loop or PLL. The tube is free to resonate when 9-micrometer thin polyvinylidene fluoride transducer is energized. It is observed that a film of such material can easily be used to produced the requisite vibrations in the tube. (author)

  3. Lanthanum fluoride nanoparticles for radiosensitization of tumors

    Science.gov (United States)

    Kudinov, Konstantin; Bekah, Devesh; Cooper, Daniel; Shastry, Sathvik; Hill, Colin; Bradforth, Stephen; Nadeau, Jay

    2016-03-01

    Dense inorganic nanoparticles have recently been identified as promising radiosensitizers. In addition to dose enhancement through increased attenuation of ionizing radiation relative to biological tissue, scintillating nanoparticles can transfer energy to coupled photosensitizers to amplify production of reactive oxygen species, as well as provide UVvisible emission for optical imaging. Lanthanum fluoride is a transparent material that is easily prepared as nanocrystals, and which can provide radioluminescence at a number of wavelengths through simple substitution of lanthanum ions with other luminescent lanthanides. We have prepared lanthanum fluoride nanoparticles doped with cerium, terbium, or both, that have good spectral overlap with chlorine6 or Rose Bengal photosensitizer molecules. We have also developed a strategy for stable conjugation of the photosensitizers to the nanoparticle surface, allowing for high energy transfer efficiencies on a per molecule basis. Additionally, we have succeeded in making our conjugates colloidally stable under physiological conditions. Here we present our latest results, using nanoparticles and nanoparticle-photosensitizer conjugates to demonstrate radiation dose enhancement in B16 melanoma cells. The effects of nanoparticle treatment prior to 250 kVp x-ray irradiation were investigated through clonogenic survival assays and cell cycle analysis. Using a custom apparatus, we have also observed scintillation of the nanoparticles and conjugates under the same conditions that the cell samples are irradiated.

  4. 21 CFR 355.70 - Testing procedures for fluoride dentifrice drug products.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Testing procedures for fluoride dentifrice drug... Procedures § 355.70 Testing procedures for fluoride dentifrice drug products. (a) A fluoride dentifrice drug... tests: Enamel solubility reduction or fluoride enamel uptake. The testing procedures for...

  5. Effects of configurational changes on molecular dynamics in polyvinylidene fluoride and poly(vinylidene fluoride-trifluoroethylene) ferroelectric polymers

    Energy Technology Data Exchange (ETDEWEB)

    Jalarvo, N., E-mail: jalarvonh@ornl.gov, E-mail: abhijit.pramanick@gmail.com, E-mail: omardiallos@ornl.gov [Jülich Centre for Neutron Science, Forschungszentrum Jülich GmbH, 52428 Jülich (Germany); Chemical and Engineering Materials Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Pramanick, A., E-mail: jalarvonh@ornl.gov, E-mail: abhijit.pramanick@gmail.com, E-mail: omardiallos@ornl.gov [Department of Physics and Materials Science, City University of Hong Kong, Kowloon (Hong Kong); Do, C. [Biology and Soft-Matter Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Diallo, S. O., E-mail: jalarvonh@ornl.gov, E-mail: abhijit.pramanick@gmail.com, E-mail: omardiallos@ornl.gov [Chemical and Engineering Materials Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States)

    2015-08-24

    We present a comparative study of proton dynamics in unpoled non-ferroelectric polymer polyvinylidene fluoride (PVDF) and in its trifluoroethylene containing ferroelectric copolymer (with 70/30 molar proportion), using quasi-elastic neutron scattering. The neutron data reveal the existence of two distinct types of molecular motions in the temperature range investigated. The slower motion, which is characterized in details here, is ascribed to protons jump diffusion along the polymeric carbon chains, while the faster motion could be attributed to localized rotational motion of methylene groups. At temperatures below the Curie point (T{sub c} ∼ 385 K) of the composite polymer, the slower diffusive mode experiences longer relaxation times in the ferroelectric blend than in the bare PVDF, although the net corresponding diffusion coefficient remains comparatively the same in both polymers with characteristic activation energy of E{sub A} ≈ 27–33 kJ/mol. This arises because of a temperature dependent jump length r{sub 0}, which we observe to be effectively longer in the copolymer, possibly due to the formation of ordered ferroelectric domains below T{sub c}. Above T{sub c}, there is no appreciable difference in r{sub 0} between the two systems. This observation directly relates the known dependence of T{sub c} on molar ratio to changes in r{sub 0}, providing fundamental insight into the ferroelectric properties of PVDF-based copolymers.

  6. Loss on drying, calcium concentration and pH of fluoride dentifrices

    Directory of Open Access Journals (Sweden)

    Arella Cristina Muniz Brito

    2015-01-01

    Full Text Available Introduction: Fluoride dentifrices containing calcium carbonate have advantages such as control of dental plaque and progression of dental caries, also contributing to oral hygiene, represent most dentifrices marketed in Brazil. Aim: To evaluate the physicochemical properties of seven fluoride dentifrices containing calcium carbonate in relation to hydrogen potential (pH, loss on drying and calcium concentration. Materials and Methods: Data collection was performed using the potentiometric method for pH ranges, gravimetric analysis for loss on drying and atomic absorption spectrometry for the concentration of calcium ions. All tests were performed in triplicate and the analysis was performed entirely at random according to one-way analysis of variance at 5% significance level. Results: The pH values were alkaline and ranged from 8.67 (Oral-B 123® to 10.03 (Colgate Mαxima Proteηγo Anticαries® . The results of loss on drying ranged from 33.81% (Oral-B 123® to 61.13% (Close Up® , with significant differences between brands tested. In relation to the calcium content, the highest and lowest concentrations were found in dentifrices Even® (155.55 g/kg and Colgate Ultra Branco® (129 g/kg, respectively, with significant difference (P < 0.05. Conclusion: Fluoride dentifrices analyzed showed alkaline pH and high levels of loss on drying and calcium concentration. However, these physicochemical characteristics differed according to the different brands tested.

  7. High Fluoride Dentifrices for Elderly and Vulnerable Adults

    DEFF Research Database (Denmark)

    Ekstrand, Kim Rud

    2016-01-01

    The primary aim of this work is to present the available evidence that toothpastes containing >1,500 ppm fluoride (2,500-2,800 and 5,000 ppm F) provide an additional caries preventive effect on root caries lesions in elderly patients compared to traditional dentifrices (1,000-1,450 ppm F). The se......The primary aim of this work is to present the available evidence that toothpastes containing >1,500 ppm fluoride (2,500-2,800 and 5,000 ppm F) provide an additional caries preventive effect on root caries lesions in elderly patients compared to traditional dentifrices (1,000-1,450 ppm F......). The secondary aim of this paper is to discuss why high fluoride dentifrices in general should perform better than traditional F-containing toothpaste. When examining the few studies that have considered the preventive benefits of high fluoride products on root caries the relative risk appears to be around 0.......5, and the risk can thus be halved by exchanging traditional F-containing toothpaste for toothpaste containing 5,000 ppm F. There is reasonable evidence that high fluoride dentifrices significantly increase the fluoride concentration in saliva during the day and the fluoride concentration in plaque compared...

  8. The effective use of fluorides in public health

    DEFF Research Database (Denmark)

    Jones, Sheila; Burt, Brian A; Petersen, Poul Erik;

    2005-01-01

    Dental caries remain a public health problem for many developing countries and for underprivileged populations in developed countries. This paper outlines the historical development of public health approaches to the use of fluoride and comments on their effectiveness. Early research and developm......Dental caries remain a public health problem for many developing countries and for underprivileged populations in developed countries. This paper outlines the historical development of public health approaches to the use of fluoride and comments on their effectiveness. Early research...... and development was concerned with waterborne fluorides, both naturally occurring and added, and their effects on the prevalence and incidence of dental caries and dental fluorosis. In the latter half of the 20th century, the focus of research was on fluoride toothpastes and mouth rinses. More recently......, systematic reviews summarizing these extensive databases have indicated that water fluoridation and fluoride toothpastes both substantially reduce the prevalence and incidence of dental caries. We present four case studies that illustrate the use of fluoride in modern public health practice, focusing on...

  9. Synthesis of nanocrystalline mixed metal fluorides in nonaqueous medium

    Indian Academy of Sciences (India)

    Neetu Tyagi; Epsita Ghanti; Nikesh Gupta; N P Lalla; Rajamani Nagarajan

    2009-12-01

    Synthesis of mixed metal fluorides of the general formula, KMF3 (M = Mg, Mn, Co, Ni, Cu and Zn), possessing perovskite structure was investigated in non-aqueous medium. The fluorides were characterized by powder X-ray diffraction, FT–IR spectroscopy, thermal analysis, SEM and TEM. Monophasic cubic phases were obtained for the central metal ions such as Mg, Mn, Co, Ni, and Zn and a tetragonally distorted phase was observed for Cu. The usage of non-aqueous medium is advantageous for the bulk synthesis of these fluorides, since it eliminated the generation and handling of the hazardous HF that has usually been encountered during aqueous preparations. The average crystallite size of the fluorides obtained by this approach was estimated to be in the range of 9–30 nm. SEM micrographs of KZnF3 showed cubic morphology of perovskite phases. TEM studies on KCuF3 confirmed the presence of tetragonal distortion. The fluoride content was determined by titrimetry and found to be nearly stoichiometric. Some of these fluorides were found to be thermally stable up to 225°C in air. These fluorides were employed as fluorinating agents in organic fluorination reactions, thereby suggesting their possible utilization for selective fluorination of aliphatic and aromatic hydrofluorocarbons (HFCs) that are industrially relevant.

  10. Fluoride Levels of Mothers' Breast Milk in Egypt

    Directory of Open Access Journals (Sweden)

    Ghada, Z A Soliman and Tamer M M Saad

    2012-01-01

    Full Text Available Introduction: Fluoride exists naturally in water sources and is derived from fluorine. It is well known that fluoride helps, prevent and even reverse the early stages of tooth decay. Aim: The aim of the present study was to determine the fluoride levels in plasma and breast milk of lactating mothers in Egypt (Cairo and Giza Governorate. Material and Methods: Two hundred healthy lactating mothers aged between 20-40 years old were asked to give plasma and milk samples voluntary. Breast milk samples were directly refrigerated until measurements. The fluoride concentrations of plasma, milk and drinking tap water were assessed using an ion-selective fluoride electrode combined with an ion analyzer. Results: The fluoride levels of plasma, breast milk and drinking tap water samples were 0.0207±0.012, 0.0111±0.0044 ppm, and 0.482±0.117 ppm, respectively. A significant direct correlation between fluoride content in breast milk and drinking tap water was found (r=0.858, p< 0.01.

  11. Amelioration of Fluoride Toxicity with the Use of Indigenous Inputs

    Directory of Open Access Journals (Sweden)

    Maitra A.

    2013-08-01

    Full Text Available An assessment was undertaken to study the efficacy of bacterial consortia isolated from different sources viz. rhizosphere of rice plant, oil spill sites of a petrol pump and from the sludge of a pharmaceutical waste water drain against the impact of fluoride. The experiments were conducted with two crops. In this mung bean experiment Vigna radiata was selected as a test crop. The seeds were sown in the field with bacterial consortia, compost and reduced dose (25% less nitrogen than recommended dose of chemical fertilizer. After 30days of seed sowing (DAS, plants were collected from the field and dipped into the sodium fluoride solution with different concentrations for 48 hours. Thereafter, the impact of fluoride on chlorophyll, sugar, proline and relative water content (% were evaluated. Scanning electron microscopy (SEM of the stem section was performed. SEM studies revealed that anatomical structure deformed with 1.5 mg/l sodium fluoride solution. It was observed that such treatment combination during the sowing of crops leads to combat the impact of lower doses of sodium fluoride (0.2 mg/l. Another experiment was also conducted within plastic pots with and without bacterial consortia isolated from rhizosphere of rice plant and oil spilled soil of petrol pump with the same field soil. Each pot was filled with 5 kg of soil + 2lt of water (on the basis of soil saturation. Oryza sativa seedlings were transplanted with different strength of sodium fluoride solution (25 mgNaF/kg, 50 mgNaF/kg, 100 mgNaF/kg and 500mgNaF/kg within the above pots. In second experiment, rice plants dried in all pots after 500 mgNaF/kg concentration of sodium fluoride. In this pot experiment bacterial strain are capable of reducing fluoride content in soil as noted by measuring fluoride in the pot soil after the experiment.

  12. Serum fluoride and sialic acid levels in osteosarcoma.

    Science.gov (United States)

    Sandhu, R; Lal, H; Kundu, Z S; Kharb, S

    2011-12-01

    Osteosarcoma is a rare malignant bone tumor most commonly occurring in children and young adults presenting with painful swelling. Various etiological factors for osteosarcoma are ionizing radiation, family history of bone disorders and cancer, chemicals (fluoride, beryllium, and vinyl chloride), and viruses. Status of fluoride levels in serum of osteosarcoma is still not clear. Recent reports have indicated that there is a link between fluoride exposure and osteosarcoma. Glycoproteins and glycosaminoglycans are an integral part of bone and prolonged exposure to fluoride for long duration has been shown to cause degradation of collagen and ground substance in bones. The present study was planned to analyze serum fluoride, sialic acid, calcium, phosphorus, and alkaline phosphatase levels in 25 patients of osteosarcoma and age- and sex-matched subjects with bone-forming tumours other than osteosarcoma and musculo-skeletal pain (controls, 25 each). Fluoride levels were analyzed by ISE and sialic acid was analyzed by Warren's method. Mean serum fluoride concentration was found to be significantly higher in patients with osteosarcoma as compared to the other two groups. The mean value of flouride in patients with other bone-forming tumors was approximately 50% of the group of osteosarcoma; however, it was significantly higher when compared with patients of group I. Serum sialic acid concentration was found to be significantly raised in patients with osteosarcoma as well as in the group with other bone-forming tumors as compared to the group of controls. There was, however, no significant difference in the group of patients of osteosarcoma when compared with group of patients with other bone-forming tumors. These results showing higher level of fluoride with osteosarcoma compared to others suggesting a role of fluoride in the disease.

  13. Pharmacokinetics of Fluoride in Toddlers After Application of 5% Sodium Fluoride Dental Varnish

    OpenAIRE

    Milgrom, Peter; Taves, Donald M.; Kim, Amy S.; Watson, Gene E; Jeremy A Horst

    2014-01-01

    The prevalence of dental caries (tooth decay) among preschool children is increasing, driven partially by an earlier age of onset of carious lesions. The American Academy of Pediatrics recommends application of 5% sodium fluoride varnish at intervals increasing with caries risk status, as soon as teeth are present. However, the varnishes are marketed for treatment of tooth sensitivity and are regulated as medical devices rather than approved by the US Food and Drug Administration for preventi...

  14. Fluoride varnishes with calcium glycerophosphate: fluoride release and effect on in vitro enamel demineralization

    Directory of Open Access Journals (Sweden)

    Thiago Saads CARVALHO

    2015-01-01

    Full Text Available The aims of this study were (1 to assess the amount of fluoride (F released from varnishes containing calcium glycerophosphate (CaGP and (2 to assess the effect of the experimental varnishes on in vitro demineralization. Six test groups using 5 varnishes: base varnish (no active ingredients; Duraphat® (2.26% NaF; Duofluorid® (5.63% NaF/CaF2; experimental varnish 1 (1% CaGP/5.63% NaF/CaF2; experimental varnish 2 (5% CaGP/5.63% NaF/CaF2; and no varnish were set up. In stage 1, 60 acrylic blocks were randomly distributed into 6 groups (n = 10. Then 300 µg of each varnish was applied to each block. The blocks were immersed in deionized water, which was changed after 1, 8, 12, 24, 48 and 72 hours. Fluoride concentration in the water was analyzed using a fluoride electrode. In stage 2, 60 bovine enamel samples were distributed into 6 groups (n = 10, and treated with 300 µg of the respective varnish. After 6 h the varnish was removed and the samples were subjected to a 7-day in vitro pH cycle (6 h demineralization/18 h remineralization per day. The demineralization was measured using surface hardness. The results showed that both experimental varnishes released more fluoride than Duofluorid® and Duraphat® (p < 0.05, but Duraphat® showed the best preventive effect by decreasing enamel hardness loss (p < 0.05. Therefore, we conclude that even though (1 the experimental varnishes containing CaGP released greater amounts of F, (2 they did not increase in the preventive effect against enamel demineralization.

  15. Graphene Fluoride: A Stable Stoichiometric Graphene Derivative and its Chemical Conversion to Graphene

    OpenAIRE

    Zbořil, Radek; Karlický, František; Bourlinos, Athanasios B.; Steriotis, Theodore A.; Athanasios K. Stubos; Georgakilas, Vasilios; Šafářová, Klára; Jančík, Dalibor; Trapalis, Christos; Otyepka, Michal

    2010-01-01

    Stoichoimetric graphene fluoride monolayers are obtained in a single step by the liquid-phase exfoliation of graphite fluoride with sulfolane. Comparative quantum-mechanical calculations reveal that graphene fluoride is the most thermodynamically stable of five studied hypothetical graphene derivatives; graphane, graphene fluoride, bromide, chloride, and iodide. The graphene fluoride is transformed into graphene via graphene iodide, a spontaneously decomposing intermediate. The calculated ban...

  16. Solubility of fluorides of alkaline earth metals and some rare earths in anhydrous trifluoroacetic acid

    International Nuclear Information System (INIS)

    Solubility of fluorides of alkaline earth and some rare earth metals in anhydrous trifluoroacetic acid is studied. For each type of fluoride solubility depends on the ionic radius of the cation. Solubility of fluorides of alkaline earth metals grows from magnesium to barium. All the fluorides in anhydrous trifluoroacetic acid form solvates. Solvates of strontium and scandium fluorides are shown to decompose at 110 and 150 deg C respectively

  17. Spectrophotometric determination of fluorides in water with Hach equipment

    International Nuclear Information System (INIS)

    The spectrophotometric method for the determination of the fluoride ion in water, demineralized water, raw waters, laundry waters and waters treated with ion exchange resins , using the technique and the SPADNS coloring indicated in the operation manual of the Hach equipment is described. This method covers the determination of the fluoride ion in the range from 0 to 2 mg/l on 25 ml. of radioactive base sample. These limits can be variable if the size of the used aliquot one is changed for the final determination of the fluoride ion. (Author)

  18. Nitrogen Trifluoride-Based Fluoride- Volatility Separations Process: Initial Studies

    Energy Technology Data Exchange (ETDEWEB)

    McNamara, Bruce K.; Scheele, Randall D.; Casella, Andrew M.; Kozelisky, Anne E.

    2011-09-28

    This document describes the results of our investigations on the potential use of nitrogen trifluoride as the fluorinating and oxidizing agent in fluoride volatility-based used nuclear fuel reprocessing. The conceptual process uses differences in reaction temperatures between nitrogen trifluoride and fuel constituents that produce volatile fluorides to achieve separations and recover valuable constituents. We provide results from our thermodynamic evaluations, thermo-analytical experiments, kinetic models, and provide a preliminary process flowsheet. The evaluations found that nitrogen trifluoride can effectively produce volatile fluorides at different temperatures dependent on the fuel constituent.

  19. Determination of fluoride content in toothpaste using spectrophotometry

    Directory of Open Access Journals (Sweden)

    Susanti Pudji Hastuti

    2013-09-01

    Full Text Available Background: Intake excessive fluoride in children’s teeth are generally marked with white and brown patches. Excessive fluoride of more than 4.0 mg/L can cause a person suffering from poisoning, fragility of the bones (osteoporosis, liver and kidney damage. Knowledge about the spectrophotometry for determination method of fluoride content in commercially available toothpaste is very few. Purpose: The purposes of study were to examine the suitable method for fluoride extraction and to determine out the accuracy, precision, linearity, and stability of the measurement method of fluoride content in toothpaste. Methods: The suitable F extraction method was determined by the comparison among 3 methods of extraction; e.g. the dried samples were immersed in (1 distilled water, (2 96% HCl, and (3 96% HNO3; and the validation methods of measurement were the maximum wavelength, standart curve, accuracy test, precision test, and stability test. Results: Result showed that the fluoride extraction by using the concentrated HNO3 was found to have the highest levels of fluoride, followed by hydrochloric acid dissolution (HCl and distilled water, while the method of validation showed that SPADNS revealed the acceptable accuracy. Precision has the RSD ≤ 2.00%. Furthermore the stability test result showed that the measurement of fluoride less than 2 hours was still reliable. Conclusion: The study suggested that the best result of fluoride extraction from toothpaste could be gained by using concentrate HNO3, and the spectrophotometer (UV-Vis Mini Shimadzu U-1240 and SPADNS have the acceptable accuracy.Latar Belakang: Pemasukan fluoride yang berlebihan pada gigi anak ditandai dengan bercak putih dan coklat. Fluoride lebih dari 4.0 mg / L dapat menyebabkan seseorang menderita keracunan , kerapuhan tulang (osteoporosis, kerusakan hati dan ginjal. Pengetahuan tentang spektrofotometri untuk metode penentuan kadar fluoride dalam pasta gigi yang tersedia secara

  20. Using High Fluoride Concentration Products in Public Policy: A Rapid Review of Current Guidelines for High Fluoride Concentration Products.

    Science.gov (United States)

    Douglas, Gail V A; Ramsdale, Martin P; Vinall-Collier, Karen; Csikar, Julia I

    2016-01-01

    Despite improvements in dental caries levels since the widespread introduction of fluoride toothpastes, it is still a disease which is considered to be a priority in many countries around the world. Individuals at higher risk of caries can be targeted with products with a high fluoride concentration to help reduce the amount and severity of the disease. This paper compares guidance from around the world on the use of products with a high fluoride concentration and gives examples of how guidance has been translated into activity in primary care dental practice. A rapid review of electronic databases was conducted to identify the volume and variation of guidance from national or professional bodies on the use of products with a high fluoride concentration. Fifteen guidelines published within the past 10 years and in English were identified and compared. The majority of these guidelines included recommendations for fluoride varnish use as well as for fluoride gels, while a smaller number offered guidance on high fluoride strength toothpaste and other vehicles. Whilst there was good consistency in recommendations for fluoride varnish in particular, there was sometimes a lack of detail in other areas of recommendation for other vehicles with a high fluoride concentration. There are good examples within the UK, such as the Childsmile project and Delivering Better Oral Health, which highlight that the provision of evidence-based guidance can be influential in directing scarce resources towards oral health improvements. Policy can be influenced by evidence-based national recommendations and used to help encourage dental professionals and commissioners and third-party payers to adopt higher levels of practices aimed at oral health improvement. PMID:27100106

  1. The impact of geology on the migration of fluorides in mineral waters of the Bukulja and Brajkovac pluton area, Serbia

    Directory of Open Access Journals (Sweden)

    Papić Petar

    2012-01-01

    Full Text Available One of the hydrogeochemical parameters that classify groundwater as mineral water is the content of fluoride ions. Their concentration is both important and limited for bottled mineral waters. Hydrochemical research of mineral waters in the surrounding area of Bukulja and Brajkovac pluton, in central Serbia, was conducted in order to define the chemical composition and genesis of these waters. They are carbonated waters, with content of fluoride ranging from 0.2 up to 6.6 mg/L. Since hydrochemical analyses showed variations in the major water chemistry, it was obvious that, apart from hydrochemical research, some explorations of the structure of the regional terrain would be inevitable. For these purposes, some additional geological research was performed, creating an adequate basis for the interpretation of the genesis of these carbonated mineral waters. The results confirmed the significance of the application of hydrochemical methods in the research of mineral waters. The work tended to emphasize that “technological treatment” for decreasing the concentration of fluoride in mineral waters occurs in nature, indicating the existence of natural defluoridization. [Projekat Ministarstva nauke Republike Srbije, br. 43004

  2. Cerium fluoride crystals for calorimetry at LHC

    International Nuclear Information System (INIS)

    High-resolution homogeneous calorimetry is fully justified for part of the physics program at the Large Hadron Collider (LHC). The main design features of proposed CeF3 crystals for calorimetry for LHC are discussed. The severe constraints LHC imposes on detectors make the use of 'classical' crystals impossible. Therefore, a large R and D effort has been undertaken by the 'Crystal Clear' collaboration in order to find new, dense, fast and radiation hard crystals. A good candidate, cerium fluoride, has been identified and studied. It is interesting at this stage to review the specifications of scintillators for LHC and to see how well available data on CeF3 luminescence, decay time, light yield, optical transmission and resistance to radiation meet them. Milestones to reach before starting a large scale crystal production in view of the eventual construction of a calorimeter, are also discussed. (author) 15 refs., 15 figs., 1 tab

  3. Further results on cerium fluoride crystals

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, S.; Auffray, E.; Aziz, T.; Baccaro, S.; Banerjee, S.; Bareyre, P.; Barone, L.E.; Borgia, B.; Boutet, D.; Burq, J.P.; Chemarin, M.; Chipaux, R.; Dafinei, I.; D' Atanasio, P.; De Notaristefani, F.; Dezillie, B.; Dujardin, C.; Dutta, S.; Faure, J.L.; Fay, J.; Ferrere, D.; Francescangeli, O.; Fuchs, B.A.; Ganguli, S.N.; Gillespie, G.; Goyot, M.; Gupta, S.K.; Gurtu, A.; Heck, J.; Herve, A.; Hillemanns, H.; Holdener, F.; Ille, B.; Joensson, L.; Kierstead, J.; Krenz, W.; Kway, W.; Le Goff, J.M.; Lebeau, M.; Lebrun, P.; Lecoq, P.; Lemoigne, Y.; Loomis, G.; Lubelsmeyer, K.; Madjar, N.; Majni, G.; El Mamouni, H.; Mangla, S.; Mares, J.A.; Martin, J.P.; Mattioli, M.; Mauger, G.J.; Mazumdar, K.; Mengucci, P.; Merlo, J.P.; Moine, B.; Nikl, N.; Pansart, J.P.; Pedrini, C.; Poinsignon, J.; Polak, K.; Raghavan, R.; Rebourgeard, P.; Rinaldi, D.; Rosa, J.; Rosowsky, A.; Sahuc, P.; Samsonov, V.; Sarkar, S.; Schegelski, V.; Schmitz, D.; Schneegans, M.; Seliverstov, D.; Stoll, S.; Sudhakar, K.; Sven; Crystal Clear Collaboration

    1993-08-15

    A systematic investigation of the properties of cerium fluoride monocrystals has been performed by the 'Crystal Clear' collaboration in view of a possible use of such crystals for the construction of high precision electromagnetic calorimeters for the future generation of high luminosity accelerators. A large sample of different crystals grown by several producers has been studied. The spectroscopic characteristics, the transmission, luminescence and excitation spectra and the decay time curves are analysed. The light yield of the different crystals is measured with photomultipliers and Si photodiodes and compared to reference standards like BGO and NaI(Tl). The radiation damage behaviour is then presented for [gamma] and neutron irradiations, at different doses and dose rates, including thermal and optical bleaching. (orig.)

  4. A highly sensitive colorimetric and ratiometric sensor for fluoride ion

    Institute of Scientific and Technical Information of China (English)

    Zhao Wu Xu; Jin Tang; He Tian

    2008-01-01

    A new benzoimidazole-naphthalimide derivative 4 was synthesized and its photophysical properties were studied.This compound showed highly selectively and sensitive colorimetric and ratiometric sensing ability for fluoride anion.

  5. Preparation and Characterization of Rare Earth Doped Fluoride Nanoparticles

    Directory of Open Access Journals (Sweden)

    Timothy A. DeVol

    2010-03-01

    Full Text Available This paper reviews the synthesis, structure and applications of metal fluoride nanoparticles, with particular focus on rare earth (RE doped fluoride nanoparticles obtained by our research group. Nanoparticles were produced by precipitation methods using the ligand ammonium di-n-octadecyldithiophosphate (ADDP that allows the growth of shells around a core particle while simultaneously avoiding particle aggregation. Nanoparticles were characterized on their structure, morphology, and luminescent properties. We discuss the synthesis, properties, and application of heavy metal fluorides; specifically LaF3:RE and PbF2, and group IIA fluorides. Particular attention is given to the synthesis of core/shell nanoparticles, including selectively RE-doped LaF3/LaF3, and CaF2/CaF2 core/(multi-shell nanoparticles, and the CaF2-LaF3 system.

  6. Estuarine response of fluoride - Investigations in Azhikode Estuary

    Digital Repository Service at National Institute of Oceanography (India)

    Balachandran, K.K.; Joseph, T.; Sankaranarayanan, V.N.

    behaved conservatively during the postmonsoon season. However, during the premonsoon season 25% removal of fluoride was observed due to estuarine mixing. The possible mechanisms for the removal are explained....

  7. Quantitative measure for the "nakedness" of fluoride ion sources.

    Science.gov (United States)

    Christe, Karl O; Jenkins, H Donald Brooke

    2003-08-01

    A quantitative measure for the donor strength or "nakedness" of fluoride ion donors is presented. It is based on the free energy change associated with the transfer of a fluoride ion from the donor to a given acceptor molecule. Born-Haber cycle calculations were used to calculate both the free energy and the enthalpy change for this process. The enthalpy change is given by the sum of the fluoride ion affinity of the acceptor (as defined in strict thermodynamic convention) and the lattice energy difference (DeltaU(POT)) between the fluoride ion donor and the salt formed with the acceptor. Because, for a given acceptor, the fluoride affinity has a constant value, the relative enthalpy (and also the corresponding free energy) changes are governed exclusively by the lattice energy differences. In this study, BF(3), PF(5), AsF(5), and SbF(5) were used as the acceptors, and the following seven fluoride ion donors were evaluated: CsF, N(CH(3))(4)F (TMAF), N-methylurotropinium fluoride (MUF), hexamethylguanidinium fluoride (HMGF), hexamethylpiperidinium fluoride (HMPF), N,N,N-trimethyl-1-adamantylammonium fluoride (TMAAF), and hexakis(dimethylamino)phosphazenium fluoride (HDMAPF). Smooth relationships between the enthalpy changes and the molar volumes of the donor cations were found which asymptotically approach constant values for infinitely large cations. Whereas CsF is a relatively poor F(-) donor [(U(POT)(CsF) - U(POT)(CsSbF(6))) = 213 kJ mol(-)(1)], when compared to N(CH(3))(4)F [(U(POT)(TMAF) - U(POT)(TMASbF(6))) = 69 kJ mol(-)(1)], a 4 times larger cation (phosphazenium salt) and an infinitely large cation are required to decrease DeltaU(POT) to 17 and 0 kJ mol(-)(1), respectively. These results clearly demonstrate that very little is gained by increasing the cation size past a certain level and that secondary factors, such as chemical and physical properties, become overriding considerations.

  8. EXPERIMENTAL STUDY AND NUMERICAL SIMULATION OF FLUORIDE IN SAND

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hong-mei; SU Bao-yu

    2006-01-01

    The transport and transformation of fluoride in sand were studied by using soil tank test under the condition of saturated water in this article. Based on the analysis of the laboratory experiments, the rules of fluorine transportation and transformation were simulated in sand by solving the advection-diffusion equation. Through comparison between computed results and observed data , it is shown that the established model and determined parameters could be used to simulate the fluoride transport in sand.

  9. Preparation and Characterization of Rare Earth Doped Fluoride Nanoparticles

    OpenAIRE

    DeVol, Timothy A.; Basak Yazgan-Kukouz; Baris Kokuoz; DiMaio, Jeffrey R.; Kevin B. Sprinkle; James, Tiffany L.; Kucera, Courtney J.; Jacobsohn, Luiz G.; John Ballato

    2010-01-01

    This paper reviews the synthesis, structure and applications of metal fluoride nanoparticles, with particular focus on rare earth (RE) doped fluoride nanoparticles obtained by our research group. Nanoparticles were produced by precipitation methods using the ligand ammonium di-n-octadecyldithiophosphate (ADDP) that allows the growth of shells around a core particle while simultaneously avoiding particle aggregation. Nanoparticles were characterized on their structure, morphology, and luminesc...

  10. Thermodynamic investigation of fluoride salts for nuclear energy production

    OpenAIRE

    Beilmann, Markus

    2013-01-01

    In this work thermodynamic properties of molten fluoride salts and salt mixtures are investigated. Fluoride salts have advantageous properties to be used in energy producing systems based on the conversion from heat to energy like i.e in Molten Salt Reactors. For this purpose it is very important to have detailed information about the heat capacity of the pure salts and salt mixtures. To get a better understanding about the heat capacity in mixtures drop calorimetry measurements of mixture...

  11. Fluoride-assisted synthesis of bimodal microporous SSZ-13 zeolite.

    Science.gov (United States)

    Zhu, Xiaochun; Kosinov, Nikolay; Hofmann, Jan P; Mezari, Brahim; Qian, Qingyun; Rohling, Roderigh; Weckhuysen, Bert M; Ruiz-Martínez, Javier; Hensen, Emiel J M

    2016-02-21

    The presence of small amount of fluoride in alkaline hydrothermal synthesis of SSZ-13 zeolite yields bimodal microporous particles with substantially improved performance in the methanol-to-olefins (MTO) reaction. Hydrocarbon uptake measurements and fluorescence microspectroscopy of spent catalysts demonstrate enhanced diffusion through micropores at the grain boundaries of nanocrystals running through the zeolite particles. Fluoride-assisted SSZ-13 synthesis is a cheap and scalable approach to optimize the performance of MTO zeolite catalysts. PMID:26810114

  12. Heterolysis of Dihydrogen by Silver Alkoxides and Fluorides.

    Science.gov (United States)

    Tate, Brandon K; Nguyen, Jenna T; Bacsa, John; Sadighi, Joseph P

    2015-07-01

    Alkoxide-bridged disilver cations react with dihydrogen to form hydride-bridged cations, releasing free alcohol. Hydrogenolysis of neutral silver fluorides affords hydride-bridged disilver cations as their bifluoride salts. These reactions proceed most efficiently when the supporting ligands are expanded N-heterocyclic carbenes (NHCs) derived from 6- and 7-membered cyclic amidinium salts. Kinetics studies show that silver fluoride hydrogenolysis is first-order in both silver and dihydrogen.

  13. The economic value of Quebec’s water fluoridation program

    OpenAIRE

    Tchouaket, Eric; Brousselle, Astrid; Fansi, Alvine; Dionne, Pierre Alexandre; Bertrand, Elise; Fortin, Christian

    2013-01-01

    Aim Dental caries is a major public health problem worldwide, with very significant deleterious consequences for many people. The available data are alarming in Canada and the province of Quebec. The water fluoridation program has been shown to be the most effective means of preventing caries and reducing oral health inequalities. This article analyzes the cost-effectiveness of Quebec’s water fluoridation program to provide decision-makers with economic information for assessing its usefulnes...

  14. Fluoride Concentration in Drinking Water Resources; North of Iran

    Directory of Open Access Journals (Sweden)

    Amouei A.I. PhD,

    2016-03-01

    Full Text Available Aims Fluoride is one of the anions present in soil and water, and determining its level in drinking water is vital for preventing dental and bone diseases in societies. This research aimed to determine fluoride concentrations in drinking water sources of rural and urban areas of Babol City, Iran. Instrument & Methods This descriptive cross-sectional study was conducted in Babol City, Iran, in 2014. 384 water samples were taken from 43 wells and 3 springs in the rural areas, and from 20 wells, 3 water reservoirs, and the water distribution system in the urban areas. Fluoride concentrations of water samples were measured with a model DR2000 spectrophotometer using the standard SPADNS method. Data were entered to SPSS 16 software and were analyzed by ANOVA test. Findings The mean fluoride concentrations in the water samples of the deep wells were higher compared to those of the springs (p=0.01. The mean fluoride concentrations in the plains areas were higher compared to the mountainous regions (p=0.02. The mean fluoride concentrations in the wells of the urban areas, in the urban reservoirs, and in the urban water distribution system were 0.40±0.14, 0.39±0.15, and 0.40±0.15mg/l, respectively (p=0.07. Fluoride concentrations in water in urban areas during various seasons varied from 0.31 to 0.45mg/l (p=0.06. Conclusion Fluoride concentrations in all drinking water sources in urban and rural areas of Babol are less than the ranges recommended by WHO and Iranian national standards.

  15. Scientific Opinion on Dietary Reference Values for fluoride

    OpenAIRE

    EFSA Panel on Dietetic Products, Nutrition and Allergies (NDA)

    2013-01-01

    Following a request from the European Commission, the Panel on Dietetic Products, Nutrition and Allergies (NDA) derived Dietary Reference Values (DRVs) for fluoride, which are provided as Adequate Intake (AI) from all sources, including non-dietary sources. Fluoride is not an essential nutrient. Therefore, no Average Requirement for the performance of essential physiological functions can be defined. Nevertheless, the Panel considered that the setting of an AI is appropriate because of the be...

  16. Corrosion behavior of zirconia in acidulated phosphate fluoride

    OpenAIRE

    Anie Thomas; Sathyanarayanan Sridhar; Shant Aghyarian; Pilanda Watkins-curry; Chan, Julia Y.; Alessandro Pozzi; Danieli C. Rodrigues

    2016-01-01

    ABSTRACT Objective The corrosion behavior of zirconia in acidulated phosphate fluoride (APF) representing acidic environments and fluoride treatments was studied. Material and Methods Zirconia rods were immersed in 1.23% and 0.123% APF solutions and maintained at 37°C for determined periods of time. Surfaces of all specimens were imaged using digital microscopy and scanning electron microscopy (SEM). Sample mass and dimensions were measured for mass loss determination. Samples were charac...

  17. Corrosion behavior of zirconia in acidulated phosphate fluoride

    OpenAIRE

    Thomas, Anie; Sridhar, Sathyanarayanan; Aghyarian, Shant; Watkins-Curry, Pilanda; Chan, Julia Y.; Pozzi, Alessandro; Danieli C. Rodrigues

    2016-01-01

    ABSTRACT Objective The corrosion behavior of zirconia in acidulated phosphate fluoride (APF) representing acidic environments and fluoride treatments was studied. Material and Methods Zirconia rods were immersed in 1.23% and 0.123% APF solutions and maintained at 37°C for determined periods of time. Surfaces of all specimens were imaged using digital microscopy and scanning electron microscopy (SEM). Sample mass and dimensions were measured for mass loss determination. Samples were characteri...

  18. Fluoride levels in commercial dentifrices and drinking Water in Algeria

    OpenAIRE

    MERGHACHE, D.; BELLOUT, B.; MERGHACHE, S.; BOUCHERIT-ATMANI, Z.

    2011-01-01

    More and more scientific evidence show that fluorides have a cariostatic action to the plaque-saliva-tooth interface during cariogenous dissolution. Fluorides slow down demineralization and enhance remineralization. Their action is optimal, in the oral environment, when used at low concentrations on a continuous basis. The use of the fluorinated toothpastes during brushing of the teeth is a simple, rational method of daily topics application of fluorine, largely used in the context of prevent...

  19. Removal of fluoride from water using aluminium containing compounds

    Institute of Scientific and Technical Information of China (English)

    M. Karthikeyan; K. P. Elango

    2009-01-01

    Batch adsorption studies were undertaken to assess the suitability of aluminium titanate (AT) and bismuth aluminate (BA) to remove fluoride ions from water.The effect of pH,dose of adsorbent,contact time,initial concentration,co-ions and temperature on fluoride removal efficiency were studied.The amounts of fluoride ions adsorbed,at 30℃ from 4 mg/L of fluoride ion solution,by AT and BA are 0.85 and 1.55 mg/g,respectively.The experimental data fitted well to the Freundlich and Langmuir isotherms.Thermodynamic parameters such as △H~0,△S~0 and △G~0 indicated that the removal of fluoride ions by AT is exothermic and non-spontaneous while that by BA is endothermic and spontaneous.Furrier transform infrared (FT-IR) analysis and X-ray diffraction (XRD) patterns of the adsorbent before and after adsorption indicated that fluoride ions are chemisorbed by these adsorbents.

  20. Phosphate reduction in a hydroxyapatite fluoride removal system

    Science.gov (United States)

    Egner, A.

    2012-12-01

    Fluorosis is a widespread disease that occurs as a result of excess fluoride consumption and can cause severe tooth and bone deformations. To combat fluorosis, several previous studies have examined the potential to replace traditional bone char filters with synthetic hydroxyapatite. Calcite particles with a synthetic hydroxyapatite coating have been shown to effectively removed fluoride, yet the low-cost method for forming these particles leaves high amounts of phosphate both in synthesis waste-water and in filter effluent. High phosphate in filter effluent is problematic because consumption of extremely high phosphate can leach calcium from bones, further exacerbating the fluoride effect. This study examines ways of reducing and reusing waste. In particular, a method of fluoride removal is explored in which fluorapatite coatings may be formed directly. In preliminary studies, batches of 4.1g of Florida limestone (<710 μm) were equilibrated with 100 mL of 10ppm fluoride. In a control batch containing lime but no added phosphate, 14% treatment was achieved, but with added phosphate, 100% treatment was achieved in all batches. Batches with lower levels of phosphate took longer to reach 100% treatment, ranging from less than 24 hours in the highest phosphate batches to approximately 42 hours in the lowest batches. The lower levels tested were well within reasonable levels for drinking water and reached 0ppm fluoride in 42 hours or less.

  1. Community Water Fluoridation and Intelligence: Prospective Study in New Zealand.

    Science.gov (United States)

    Broadbent, Jonathan M; Thomson, W Murray; Ramrakha, Sandhya; Moffitt, Terrie E; Zeng, Jiaxu; Foster Page, Lyndie A; Poulton, Richie

    2015-01-01

    Objectives. This study aimed to clarify the relationship between community water fluoridation (CWF) and IQ. Methods. We conducted a prospective study of a general population sample of those born in Dunedin, New Zealand, between April 1, 1972, and March 30, 1973 (95.4% retention of cohort after 38 years of prospective follow-up). Residence in a CWF area, use of fluoride dentifrice and intake of 0.5-milligram fluoride tablets were assessed in early life (prior to age 5 years); we assessed IQ repeatedly between ages 7 to 13 years and at age 38 years. Results. No clear differences in IQ because of fluoride exposure were noted. These findings held after adjusting for potential confounding variables, including sex, socioeconomic status, breastfeeding, and birth weight (as well as educational attainment for adult IQ outcomes). Conclusions. These findings do not support the assertion that fluoride in the context of CWF programs is neurotoxic. Associations between very high fluoride exposure and low IQ reported in previous studies may have been affected by confounding, particularly by urban or rural status.

  2. Fluoride release from restorative materials coated with an adhesive.

    Science.gov (United States)

    Miranda, Letícia Algarves; Weidlich, Patrícia; Samuel, Susana Maria Werner; Maltz, Marisa

    2002-01-01

    The retention of both fluoride resins and resin-modified glass ionomer cements to dental tissues can be improved by the association of an adhesive system which promotes the bonding between the resin component and dentin, forming a hybrid layer. The purpose of this investigation was to evaluate if the presence of the adhesive, being part of the hybrid layer composition, interfered with the fluoride released to tooth tissues. The restorative materials studied were: Vitremer (3M), Heliomolar (Vivadent) and Z100 (3M) using an adhesive application (Scotch Bond MultiPurpose Plus--3M). Ten discs of each material were prepared: 5 were covered with the adhesive and 5 were not. The discs were immersed in individual flasks containing artificial saliva which was changed daily. Fluoride release was measured at days 1, 5, 10, 15 and 20 by a fluoride combined electrode (9609 BN--Orion) coupled to an ion analyzer (SA-720 Procyon). One-way ANOVA and the Student-Newman-Keuls test were applied to compare the materials. The results showed that the use of a dental adhesive significantly decreased the fluoride release of Vitremer and reduced the fluoride release of Heliomolar to undetectable levels with the methodology used. PMID:11870961

  3. Monitoring of fluoride in water samples using a smartphone.

    Science.gov (United States)

    Levin, Saurabh; Krishnan, Sunderrajan; Rajkumar, Samuel; Halery, Nischal; Balkunde, Pradeep

    2016-05-01

    In several parts of India, groundwater is the only reliable, year round source for drinking water. Prevention of fluorosis, a chronic disease resulting from excess intake of fluoride, requires the screening of all groundwater sources for fluoride in endemic areas. In this paper, the authors present a field deployable colorimetric analyzer based on an inexpensive smartphone embedded with digital camera for taking photograph of the colored solution as well as an easy-fit, and compact sample chamber (Akvo Caddisfly). Phones marketed by different smartphone makers were used. Commercially available zirconium xylenol orange reagent was used for determining fluoride concentration. A software program was developed to use with the phone for recording and analyzing the RGB color of the picture. Linear range for fluoride estimation was 0-2mgl(-1). Around 200 samples, which consisted of laboratory prepared as well as field samples collected from different locations in Karnataka, India, were tested with Akvo Caddisfly. The results showed a significant positive correlation between Ion Selective Electrode (ISE) method and Akvo Caddisfly (Phones A, B and C), with correlation coefficient ranging between 0.9952 and 1.000. In addition, there was no significant difference in the mean fluoride content values between ISE and Phone B and C except for Phone A. Thus the smartphone method is economical and suited for groundwater fluoride analysis in the field. PMID:26874766

  4. Fluoride and aluminum in teas and tea-based beverages

    Directory of Open Access Journals (Sweden)

    Hayacibara Mitsue Fujimaki

    2004-01-01

    Full Text Available OBJECTIVE: To evaluate fluoride and aluminum concentration in herbal, black, ready-to-drink, and imported teas available in Brazil considering the risks fluoride and aluminum pose to oral and general health, respectively. METHODS: One-hundred and seventy-seven samples of herbal and black tea, 11 types of imported tea and 21 samples of ready-to-drink tea were divided into four groups: I-herbal tea; II-Brazilian black tea (Camellia sinensis; III-imported tea (Camellia sinensis; IV-ready-to-drink tea-based beverages. Fluoride and aluminum were analyzed using ion-selective electrode and atomic absorption, respectively. RESULTS: Fluoride and aluminum levels in herbal teas were very low, but high amounts were found in black and ready-to-drink teas. Aluminum found in all samples analyzed can be considered safe to general health. However, considering 0.07 mg F/kg/day as the upper limit of fluoride intake with regard to undesirable dental fluorosis, some teas exceed the daily intake limit for children. CONCLUSIONS: Brazilian and imported teas made from Camellia sinensis as well as some tea-based beverages are sources of significant amounts of fluoride, and their intake may increase the risk of developing dental fluorosis.

  5. Using High Fluoride Concentration Products in Public Policy – A Rapid Review of Current Guidelines for High Fluoride Concentration products

    OpenAIRE

    Douglas, GVA; Ramsdale, M; Vinall, K.; Csikar, J

    2016-01-01

    Despite improvements in caries levels since widespread introduction of fluoride toothpastes it remains a priority in many countries around the world. Higher caries risk individuals can be targeted with products with a high fluoride concentration to help reduce the amount and severity of disease. This paper compares guidance from around the world on the use of such products and gives examples of how guidance has been translated into activity in primary care dental practice. A rapid review of e...

  6. High Temperature Fluoride Salt Test Loop

    Energy Technology Data Exchange (ETDEWEB)

    Aaron, Adam M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Cunningham, Richard Burns [Univ. of Tennessee, Knoxville, TN (United States); Fugate, David L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Holcomb, David Eugene [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kisner, Roger A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Peretz, Fred J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Robb, Kevin R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wilson, Dane F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yoder, Jr, Graydon L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-12-01

    Effective high-temperature thermal energy exchange and delivery at temperatures over 600°C has the potential of significant impact by reducing both the capital and operating cost of energy conversion and transport systems. It is one of the key technologies necessary for efficient hydrogen production and could potentially enhance efficiencies of high-temperature solar systems. Today, there are no standard commercially available high-performance heat transfer fluids above 600°C. High pressures associated with water and gaseous coolants (such as helium) at elevated temperatures impose limiting design conditions for the materials in most energy systems. Liquid salts offer high-temperature capabilities at low vapor pressures, good heat transport properties, and reasonable costs and are therefore leading candidate fluids for next-generation energy production. Liquid-fluoride-salt-cooled, graphite-moderated reactors, referred to as Fluoride Salt Reactors (FHRs), are specifically designed to exploit the excellent heat transfer properties of liquid fluoride salts while maximizing their thermal efficiency and minimizing cost. The FHR s outstanding heat transfer properties, combined with its fully passive safety, make this reactor the most technologically desirable nuclear power reactor class for next-generation energy production. Multiple FHR designs are presently being considered. These range from the Pebble Bed Advanced High Temperature Reactor (PB-AHTR) [1] design originally developed by UC-Berkeley to the Small Advanced High-Temperature Reactor (SmAHTR) and the large scale FHR both being developed at ORNL [2]. The value of high-temperature, molten-salt-cooled reactors is also recognized internationally, and Czechoslovakia, France, India, and China all have salt-cooled reactor development under way. The liquid salt experiment presently being developed uses the PB-AHTR as its focus. One core design of the PB-AHTR features multiple 20 cm diameter, 3.2 m long fuel channels

  7. THE EFFECT OF FLUORIDE ON LEAD SOLUBILITY

    Science.gov (United States)

    Difficulties in predicting and controlling lead corrosion are encountered by hundreds of water systems across the country. Inorganic carbonate, sulfate, silicate, orthophosphate, pH, total organic carbon, temperature and the type/amount of chlorine residual are all known factors ...

  8. Profile of Fluoride Release from a Nanohybrid Composite Resin

    Directory of Open Access Journals (Sweden)

    Raquel Assed Bezerra Silva

    2015-02-01

    Full Text Available The aim of this study was to evaluate in vitro the amount and profile of fluoride release from a fluoride-containing nanohybrid composite resin (Tetric® N-Ceram by direct potentiometry. Thirty specimens (5 mm diameter x 3 mm high; n=10/material were made of Tetric® N-Ceram, Vitremer® resin-modified glass ionomer cement (RMGIC (positive control or Filtek® Z350 nanofill composite resin (negative control. The specimens were stored individually in plastic tubes containing 1 mL of artificial saliva at 37°C, which was daily renewed during 15 days. At each renewal of saliva, the amount of fluoride ions released in the solution was measured using a fluoride ion-selective electrode with ion analyzer, and the values obtained in mV were converted to ppm (µg/mL. Data were analyzed statistically by ANOVA and Tukey’s post-hoc test at a significance level of 5%. The results showed that the resins Tetric® N-Ceram and Filtek® Z350 did not release significant amounts of fluoride during the whole period of evaluation (p>0.05. Only Vitremer® released significant amounts of fluoride ions during the 15 days of the experiment, with greater release in first 2 days (p0.05. In conclusion, the nanohybrid composite resin Tetric® N-Ceram did not present in vitro fluoride-releasing capacity throughout the 15 days of study.

  9. Compression of lithium fluoride to 92 GPa

    Science.gov (United States)

    Dong, Haini; Dorfman, Susannah M.; Holl, Christopher M.; Meng, Yue; Prakapenka, Vitali B.; He, Duanwei; Duffy, Thomas S.

    2014-01-01

    The equation of state and compression behavior of lithium fluoride, LiF, have been determined to 92 GPa by X-ray diffraction in a diamond anvil cell. A neon pressure-transmitting medium was used to minimize the effect of differential stress on the sample. Consistent results using multiple pressure standards were obtained. By fitting the pressure-volume data to a Birch-Murnaghan equation of state, the isothermal bulk modulus and its corresponding pressure derivative at zero pressure were determined to be K0=70.1±0.7 GPa, and K‧0=4.3±0.1. If the bulk modulus is fixed at 66.2 GPa, a value well constrained by independent elasticity measurements, we obtain K‧0=4.6±0.1. The bulk modulus and its pressure derivative obtained from this work resolve the large discrepancy in previously reported values of K0 and K‧0 for this material. Consequently, the equation of state of LiF is now sufficiently well constrained to allow its use as a pressure calibrant in high pressure experiments.

  10. Characterization of cerium fluoride nanocomposite scintillators

    Energy Technology Data Exchange (ETDEWEB)

    Stange, Sy [Los Alamos National Laboratory; Esch, Ernst I [Los Alamos National Laboratory; Brown, Leif O [Los Alamos National Laboratory; Couture, Aaron J [Los Alamos National Laboratory; Mckigney, Edward A [Los Alamos National Laboratory; Muenchausen, Ross E [Los Alamos National Laboratory; Del Sesto, Rico E [Los Alamos National Laboratory; Gilbertson, Robert D [Los Alamos National Laboratory; Mccleskey, T Mark [Los Alamos National Laboratory; Reifarth, Rene [Los Alamos National Laboratory

    2009-01-01

    Measurement of the neutron capture cross-sections of a number of short-lived isotopes would advance both pure and applied scientific research. These cross-sections are needed for calculation of criticality and waste production estimates for the Advanced Fuel Cycle Initiative, for analysis of data from nuclear weapons tests, and to improve understanding of nucleosynthesis. However, measurement of these cross-sections would require a detector with a faster signal decay time than those used in existing neutron capture experiments. Crystals of faster detector materials are not available in sufficient sizes and quantities to supply these large-scale experiments. Instead, we propose to use nanocomposite detectors, consisting of nanoscale particles of a scintillating material dispersed in a matrix material. We have successfully fabricated cerium fluoride (CeF{sub 3}) nanoparticles and dispersed them in a liquid matrix. We have characterized this scintillator and have measured its response to neutron capture. Results of the optical, structural, and radiation characterization will be presented.

  11. Magnetic separation of uranium from magnesium fluoride

    International Nuclear Information System (INIS)

    The attraction or repulsion of particles by a magnetic gradient, based on the respective susceptibilities, provides the basis for physical separation of particles that are comprised predominantly of uranium from those that are predominantly magnesium fluoride (MgF2). To determine the effectiveness of this approach, a bench-scale magnetic separator from the S.G. Frantz Co., Inc. was used. In the Frantz Model L-1, particles are fed through a funnel onto a vibration tray and through a magnetic field. The specific design of the Frantz magnet causes the magnetic field strength to vary along the width of the magnet, setting up a gradient. The tray in the magnetic field is split at a point about half way down its length so that the separated material does not recombine. A schematic is presented of Frantz Model L-1 CN - the same magnet configured for high gradient magnetic separation of liquid-suspended particles. Here different pole pieces create a uniform magnetic field, and stainless steel wood in the canister between the pole pieces creates the high gradient. 1 ref., 6 figs., 2 tabs

  12. Characterization of cerium fluoride nanocomposite scintillators

    International Nuclear Information System (INIS)

    Measurement of the neutron capture cross-sections of a number of short-lived isotopes would advance both pure and applied scientific research. These cross-sections are needed for calculation of criticality and waste production estimates for the Advanced Fuel Cycle Initiative, for analysis of data from nuclear weapons tests, and to improve understanding of nucleosynthesis. However, measurement of these cross-sections would require a detector with a faster signal decay time than those used in existing neutron capture experiments. Crystals of faster detector materials are not available in sufficient sizes and quantities to supply these large-scale experiments. Instead, we propose to use nanocomposite detectors, consisting of nanoscale particles of a scintillating material dispersed in a matrix material. We have successfully fabricated cerium fluoride (CeF3) nanoparticles and dispersed them in a liquid matrix. We have characterized this scintillator and have measured its response to neutron capture. Results of the optical, structural, and radiation characterization will be presented.

  13. In vivo and in vitro studies of a cetylamine fluoride mouthrinse: evaluation of a device used for in vitro experiments

    Directory of Open Access Journals (Sweden)

    CARVALHO Sílvia Magaly Sasso

    1999-01-01

    Full Text Available A mouthrinse containing cetylamine fluoride (230 ppm in fluoride was prepared for in vitro studies of fluoride clearance and adsorption by enamel and/or hydroxyapatite using a device that simulates the oral cavity. In vivo studies of fluoride clearance from this mouthrinse were conducted and compared with other fluoride sources. The amount of fluoride adsorbed to tooth blocks or powdered hydroxyapatite, both treated with this cetylamine fluoride mouthrinse once or twice a day, was determined. The results of these studies showed that it is possible to prepare a mouthrinse with cetylamine fluoride for alternative use by patients for the prevention and therapy of dental caries.

  14. Stabilization of fluoroindate glasses by magnesium fluoride and other heavy metal fluorides

    Directory of Open Access Journals (Sweden)

    B. J. Costa

    1998-06-01

    Full Text Available Their extended transparency in the IR makes them attractive for use as optical fibers for CO laser power delivery and optical amplification. This paper firstly describes the spectacular stabilizing effect of MgF2 on the binary system InF3-BaF2. The investigation of the InF3-BaF2-MgF2 system led to samples up to 5mm in thickness. Further optimization of this system was achieved by incorporation of limited amounts of other fluorides and resulted in increased resistence to devitrification. The second approach of this work was concerned to the investigation of the pseudo-ternary system InF3-GdF3-GaF3 at constant concentrations of ZnF2-SrF2-BaF2-NaF. Several compositions were studied in this system. The samples presented a better thermal stability when compared to other families of fluoride glasses. Therefore, these glasses seem to be very promising for the fabrication of special optical fibers. Thermal data are reported.

  15. Modeling and optimization of fluoride and cadmium trapping in phosphogypsum using design methodology

    Energy Technology Data Exchange (ETDEWEB)

    Hajem, Besma; Djebali, Kais; M' nif, Adel [Laboratoire de Valorisation des Ressources Naturelles et des Materiaux de Recuperation, Centre National de Recherches en Sciences des Materiaux, Pole Technologique de Borj Cedria, Hammam Lif (Tunisia)

    2010-09-15

    The manufacturing of phosphoric acid from natural calcium phosphate generates a solid residue containing 25-30% humidity. This solid residue (phosphogypsum) generates acidic solution (pH {approx} 2.5) containing several toxic ionic species, that coat its grains. Fluorides and heavy metals such as cadmium are considered the most harmful species contained in the released solution from phosphogypsum. The purpose of this work is to study the trapping of fluorides and cadmium in phosphogypsum as well as effluent neutralization before its discharge into natural recipient. Therefore, calcium carbonate finely ground was added and fully mixed with wet phosphogypsum. A four factors central composite design was used to model and to optimize the operating parameters that govern the process. The studied factors were temperature, reaction time, mass, and grains size of CaCO{sub 3}. Considered responses were pH, F{sup -}, and Cd{sup 2+} concentrations in the released solution after reaction with CaCO{sub 3}. The optimum operating conditions were quite efficient to trap, respectively, 99% Cd{sup 2+} and 97% of F{sup -} with a final pH of 6.66. So an original, easy, simple, and cost effective method to trap some toxic species on phosphogypsum through CaCO{sub 3} addition would likely to be integrated in phosphoric acid manufacturing plant. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  16. Separation of Fluoride Ions in an Electrolytic Cell by Using an AnionExchange Membrane

    International Nuclear Information System (INIS)

    Separation of fluoride ions in an electrolytic cell with an anionexchange membrane which is so-called an electrodialysis process has beenperformed. The experiment have been taken place in room temperature in anelectrolytic cell made by plexiglas consisted on anode and cathode chambersseparated by an anion exchange membrane in dimension of 4 x 4 cm. The carbonand stainless steel are applied as an anode and platinum as s' cathode. Theanolyte is a HNO3 0.3 M solution, while a solution of NaF 0.3 M, and amixture of NaF 0.3 M containing uranyl nitrate solution for separating offluoride ions and uranium are used as a catholyte. The distance between theelectrode and the membrane is 1.5 cm and this distance is kept constant. Theparameters observed are the current voltage, cathode applied, and uraniumconcentration. For the solution without uranium, the results show that thefluoride ions transferred are around 50 % using carbon as a cathode for 3hours and the voltage of 10 volts, while for SS as a cathode are around 93 %.For the solution containing uranium, the fluoride ions transferred are around78 % for 3.5 hours and the uranium ions remain in the catholyte in which mostof them are as 8 yellow deposit of Na2U2O7 on the cathode surface andothers are as a white precipitate of NaUF5 on the bottom of the cathodechamber. (author)

  17. Methyl fluoride affects methanogenesis rather than community composition of methanogenic archaea in a rice field soil.

    Directory of Open Access Journals (Sweden)

    Anne Daebeler

    Full Text Available The metabolic pathways of methane formation vary with environmental conditions, but whether this can also be linked to changes in the active archaeal community structure remains uncertain. Here, we show that the suppression of aceticlastic methanogenesis by methyl fluoride (CH(3F caused surprisingly little differences in community composition of active methanogenic archaea from a rice field soil. By measuring the natural abundances of carbon isotopes we found that the effective dose for a 90% inhibition of aceticlastic methanogenesis in anoxic paddy soil incubations was <0.75% CH(3F (v/v. The construction of clone libraries as well as t-RFLP analysis revealed that the active community, as indicated by mcrA transcripts (encoding the α subunit of methyl-coenzyme M reductase, a key enzyme for methanogenesis, remained stable over a wide range of CH(3F concentrations and represented only a subset of the methanogenic community. More precisely, Methanocellaceae were of minor importance, but Methanosarcinaceae dominated the active population, even when CH(3F inhibition only allowed for aceticlastic methanogenesis. In addition, we detected mcrA gene fragments of a so far unrecognised phylogenetic cluster. Transcription of this phylotype at methyl fluoride concentrations suppressing aceticlastic methanogenesis suggests that the respective organisms perform hydrogenotrophic methanogenesis. Hence, the application of CH(3F combined with transcript analysis is not only a useful tool to measure and assign in situ acetate usage, but also to explore substrate usage by as yet uncultivated methanogens.

  18. Calix[4]pyrrole derivative: recognition of fluoride and mercury ions and extracting properties of the receptor-based new material.

    Science.gov (United States)

    de Namor, Angela F Danil; Khalife, Rasha

    2008-12-11

    A calix[4]pyrrole derivative, namely, meso-tetramethyl tetrakis (4-phenoxy methyl ketone) calix[4]pyrrole, 1, was synthesized and structurally (1H NMR) and thermodynamically characterized. The complexing properties of this receptor with a wide variety of anions and cations in dipolar aprotic media (acetonitrile, propylene carbonate, and dimethyl sulfoxide) were investigated through 1H NMR and conductance studies. The former technique was used to assess whether or not complexation occurs and if so to identify the active sites of interaction of 1 with ions. The composition of the complexes was established by conductance measurements. It was found that in dipolar aprotic solvents, 1 interacts only with two polluting ions (fluoride and mercury). The complexation thermodynamics of 1 and these ions in these solvents is reported. The medium effect on the binding process involving the fluoride ion is discussed taking into account the solvation properties of reactants and the product. Complexes of moderate stability are found. Given that this is an important factor to consider for the recycling of the loaded material in extraction processes, 1 was treated with formaldehyde in basic medium leading to the production of a calix[4]pyrrole based material able to extract fluoride and mercury (II) ions from water. Thus the optimum conditions for the extraction of these ions from aqueous solutions were established. The material is easily recyclable using an organic acid. Final conclusions are given. PMID:19053691

  19. Calix[4]pyrrole derivative: recognition of fluoride and mercury ions and extracting properties of the receptor-based new material.

    Science.gov (United States)

    de Namor, Angela F Danil; Khalife, Rasha

    2008-12-11

    A calix[4]pyrrole derivative, namely, meso-tetramethyl tetrakis (4-phenoxy methyl ketone) calix[4]pyrrole, 1, was synthesized and structurally (1H NMR) and thermodynamically characterized. The complexing properties of this receptor with a wide variety of anions and cations in dipolar aprotic media (acetonitrile, propylene carbonate, and dimethyl sulfoxide) were investigated through 1H NMR and conductance studies. The former technique was used to assess whether or not complexation occurs and if so to identify the active sites of interaction of 1 with ions. The composition of the complexes was established by conductance measurements. It was found that in dipolar aprotic solvents, 1 interacts only with two polluting ions (fluoride and mercury). The complexation thermodynamics of 1 and these ions in these solvents is reported. The medium effect on the binding process involving the fluoride ion is discussed taking into account the solvation properties of reactants and the product. Complexes of moderate stability are found. Given that this is an important factor to consider for the recycling of the loaded material in extraction processes, 1 was treated with formaldehyde in basic medium leading to the production of a calix[4]pyrrole based material able to extract fluoride and mercury (II) ions from water. Thus the optimum conditions for the extraction of these ions from aqueous solutions were established. The material is easily recyclable using an organic acid. Final conclusions are given.

  20. Recommendations for fluoride limits in drinking water based on estimated daily fluoride intake in the Upper East Region, Ghana.

    Science.gov (United States)

    Craig, Laura; Lutz, Alexandra; Berry, Kate A; Yang, Wei

    2015-11-01

    Both dental and skeletal fluorosis caused by high fluoride intake are serious public health concerns around the world. Fluorosis is particularly pronounced in developing countries where elevated concentrations of naturally occurring fluoride are present in the drinking water, which is the primary route of exposure. The World Health Organization recommended limit of fluoride in drinking water is 1.5 mg F(-) L(-1), which is also the upper limit for fluoride in drinking water for several other countries such as Canada, China, India, Australia, and the European Union. In the United States the enforceable limit is much higher at 4 mg F(-) L(-1), which is intended to prevent severe skeletal fluorosis but does not protect against dental fluorosis. Many countries, including the United States, also have notably lower unenforced recommended limits to protect against dental fluorosis. One consideration in determining the optimum fluoride concentration in drinking water is daily water intake, which can be high in hot climates such as in northern Ghana. The results of this study show that average water intake is about two times higher in Ghana than in more temperate climates and, as a result, the fluoride intake is higher. The results also indicate that to protect the Ghanaian population against dental fluorosis, the maximum concentration of fluoride in drinking water for children under 6-8 years should be 0.6 mg F(-) L(-1) (and lower in the first two years of life), and the limit for older children and adults should be 1.0 mg F(-) L(-1). However, when considering that water treatment is not cost-free, the most widely recommended limit of 1.5 mg F(-) L(-1) - which is currently the limit in Ghana--may be appropriate for older children and adults since they are not vulnerable to dental fluorosis once the tooth enamel is formed.

  1. Recommendations for fluoride limits in drinking water based on estimated daily fluoride intake in the Upper East Region, Ghana.

    Science.gov (United States)

    Craig, Laura; Lutz, Alexandra; Berry, Kate A; Yang, Wei

    2015-11-01

    Both dental and skeletal fluorosis caused by high fluoride intake are serious public health concerns around the world. Fluorosis is particularly pronounced in developing countries where elevated concentrations of naturally occurring fluoride are present in the drinking water, which is the primary route of exposure. The World Health Organization recommended limit of fluoride in drinking water is 1.5 mg F(-) L(-1), which is also the upper limit for fluoride in drinking water for several other countries such as Canada, China, India, Australia, and the European Union. In the United States the enforceable limit is much higher at 4 mg F(-) L(-1), which is intended to prevent severe skeletal fluorosis but does not protect against dental fluorosis. Many countries, including the United States, also have notably lower unenforced recommended limits to protect against dental fluorosis. One consideration in determining the optimum fluoride concentration in drinking water is daily water intake, which can be high in hot climates such as in northern Ghana. The results of this study show that average water intake is about two times higher in Ghana than in more temperate climates and, as a result, the fluoride intake is higher. The results also indicate that to protect the Ghanaian population against dental fluorosis, the maximum concentration of fluoride in drinking water for children under 6-8 years should be 0.6 mg F(-) L(-1) (and lower in the first two years of life), and the limit for older children and adults should be 1.0 mg F(-) L(-1). However, when considering that water treatment is not cost-free, the most widely recommended limit of 1.5 mg F(-) L(-1) - which is currently the limit in Ghana--may be appropriate for older children and adults since they are not vulnerable to dental fluorosis once the tooth enamel is formed. PMID:26058000

  2. Aquaporin 5 Interacts with Fluoride and Possibly Protects against Caries.

    Directory of Open Access Journals (Sweden)

    Ida Anjomshoaa

    Full Text Available Aquaporins (AQP are water channel proteins and the genes coding for AQP2, AQP5, and AQP6 are clustered in 12q13. Since AQP5 is expressed in serous acinar cells of salivary glands, we investigated its involvement in caries. DNA samples from 1,383 individuals from six groups were studied. Genotypes of eight single nucleotide polymorphisms covering the aquaporin locus were tested for association with caries experience. Interaction with genes involved in enamel formation was tested. The association between enamel microhardness at baseline, after creation of artificial caries lesion, and after exposure to fluoride and the genetic markers in AQP5 was tested. Finally, AQP5 expression in human whole saliva, after exposure to fluoride in a mammary gland cell line, which is known to express AQP5, and in Wistar rats was also verified. Nominal associations were found between caries experience and markers in the AQP5 locus. Since these associations suggested that AQP5 may be inhibited by levels of fluoride in the drinking water that cause fluorosis, we showed that fluoride levels above optimal levels change AQP5 expression in humans, cell lines, and rats. We have shown that AQP5 is involved in the pathogenesis of caries and likely interacts with fluoride.

  3. Improved fluoride volatility reprocessing for MOX fuel cycle

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, M.; Fukasawa, T.; Sawa, T.; Yamashita, J.; Kamoshida, M.; Sasahira, A.; Kawamura, F. [Nuclear Systems Div., Hitachi, Ibaraki (Japan)

    2000-07-01

    Several countries had stopped developing fluoride volatility reprocessing method in the 1970's due to difficulties in recovering pure Pu. Although, nuclear societies recently favor dirty Pu (MOX). which has high proliferation resistance and needs remote fuel fabrication technologies. This situation reminded the authors to re-evaluate the fluoride volatility process. Preliminary investigation clarified that conventional fluoride volatility process could be simplified to recover dirty MOX and pure U from spent LWR fuels. Pure U is suitable to transfer it to re-enrichment (LWR cycle again), to storage certain period for future FBRs, and to dispose with relatively simple barrier. The improved process also enables to prepare directly the dirty MOX particles which are suitable for remote fuel fabrication (vibration packing). This paper describes the system of improved fluoride volatility reprocessing, and compatibility of each elemental process such as thermal decladding, two stage fluorination of U and U+Pu, U purification, direct conversion. of mixed fluoride into oxide particles and vibration packing fuel fabrication. (authors)

  4. A Review on Adsorption of Fluoride from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Mirna Habuda-Stanić

    2014-09-01

    Full Text Available Fluoride is one of the anionic contaminants which is found in excess in surface or groundwater because of geochemical reactions or anthropogenic activities such as the disposal of industrial wastewaters. Among various methods used for defluoridation of water such as coagulation, precipitation, membrane processes, electrolytic treatment, ion-exchange, the adsorption process is widely used. It offers satisfactory results and seems to be a more attractive method for the removal of fluoride in terms of cost, simplicity of design and operation. Various conventional and non-conventional adsorbents have been assessed for the removal of fluoride from water. In this review, a list of various adsorbents (oxides and hydroxides, biosorbents, geomaterials, carbonaceous materials and industrial products and by-products and its modifications from literature are surveyed and their adsorption capacities under various conditions are compared. The effect of other impurities on fluoride removal has also been discussed. This survey showed that various adsorbents, especially binary and trimetal oxides and hydroxides, have good potential for the fluoride removal from aquatic environments.

  5. Fluoride and aluminum release from restorative materials using ion chromatography

    Directory of Open Access Journals (Sweden)

    Zeynep Okte

    2012-02-01

    Full Text Available OBJECTIVE: The aim of this study was to determine the amounts of fluoride and aluminum released from different restorative materials stored in artificial saliva and double-distilled water. Material and METHODS: Cylindrical specimens (10 x 1 mm were prepared from 4 different restorative materials (Kavitan Plus, Vitremer, Dyract Extra, and Surefil. For each material, 20 specimens were prepared, 10 of which were stored in 5 mL artificial saliva and 10 of which were stored in 5 mL of double-distilled water. Concentrations of fluoride and aluminum in the solutions were measured using ion chromatography. Measurements were taken daily for one week and then weekly for two additional weeks. Data were analyzed using two-way ANOVA and Duncan's multiple range tests (p<0.05. RESULTS: The highest amounts of both fluoride and aluminum were released by the resin-modified glass ionomer cement Vitremer in double-distilled water (p<0.05. All materials released significantly more fluoride in double-distilled water than in artificial saliva (p<0.05. In artificial saliva, none of the materials were observed to release aluminum. CONCLUSION: It was concluded that storage media and method of analysis should be taken into account when the fluoride and aluminum release from dental materials is assessed.

  6. Corrosion Behavior of Titanium Grade 7 in Fluoride-Containing NaCl Brines

    Energy Technology Data Exchange (ETDEWEB)

    Lian, T; Whalen, M T; Wong, L

    2004-10-25

    The effects of fluoride on the corrosion behavior of Titanium Grade 7 (0.12-0.25% Pd) have been investigated. Up to 0.1 mol/L fluoride was added to the NaCl brines at 95 C, and three pH values of 4, 8, and 11 were selected for studying pH dependence of fluoride effects. It was observed that fluoride significantly altered the anodic polarization behavior, at all three pH values of 4, 8, and 11. Under acidic condition fluoride caused active corrosion. The corrosion of Titanium grade 7 was increased by three orders of magnitude when a 0.1 mol/L fluoride was added to the NaCl brines at pH 4, and the Pd ennoblement effect was not observed in acidic fluoride-containing environments. The effects of fluoride were reduced significantly when pH was increased to 8 and above.

  7. A NOVEL BIO-WASTE INCORPORATED ALGINATE SORBENT FOR DE-FLUORIDATION OF WATER

    Directory of Open Access Journals (Sweden)

    Carmalin Sophia Ayyappan

    2015-09-01

    Full Text Available This study evaluates the feasibility of using tamarind (Tamarindus indica seed powder for de-fluoridation of fluoride contaminated water. Batch study confirmed that tamarind seeds in dry powder form could remove 87% of fluoride from water. This bio-sorbent can be used effectively in areas where fluoride concentrations are above the permissible limits of 1.5 mg·l-1 as per WHO Standard, 1984. Tamarind seed powder was incorporated in a matrix of sodium alginate and made into gel-beads. The beads were tested for de-fluoridation efficiency by conducting column studies. The effect of various factors, such as flow rate, retention time, and the number of runs on the efficacy of fluoride removal was also studied. The results revealed that flow rate did not seem to have much effect on the percentage fluoride removal but the fluoride concentration decreased drastically upon greater retention time and multiple runs.

  8. Caries status in 16 year-olds with varying exposure to water fluoridation in Ireland.

    LENUS (Irish Health Repository)

    Mullen, J

    2012-12-01

    Most of the Republic of Ireland\\'s public water supplies have been fluoridated since the mid-1960s while Northern Ireland has never been fluoridated, apart from some small short-lived schemes in east Ulster.

  9. Tetrabutylammonium fluoride promoted regiospecific reactions of trimethylsilyl-o-carborane with aldehydes

    International Nuclear Information System (INIS)

    Trimethylsilyl-o-carborane serves as o-carborane carbanion upon fluoride ion promoted reaction with carbonyl compounds. Thus, in the presence of tetrabutylammonium fluoride, trimethylsilyl-o-carborane undergoes facile, unprecedented, carbodesilylation with aromatic and aliphatic aldehydes. (author)

  10. Community-oriented administration of fluoride for the prevention of dental caries

    DEFF Research Database (Denmark)

    Petersen, P E; Baez, R J; Lennon, M A

    2012-01-01

    coverage. Participants acknowledged that automatic fluoridation through water, salt, and milk is the most effective and equitable strategy for the prevention of dental caries. Concerns were expressed that government-subsidized community fluoride prevention programs may face privatization. In addition...

  11. Analyse van fluoride en fosfaat in complexe milieumatrices met capillaire zone elektroforese

    NARCIS (Netherlands)

    Staden JJ van; Hoop MAGT van den; LAC

    1996-01-01

    Dit onderzoek bestudeert de toepasbaarheid van een eerder ontwikkelde methode voor de analyse van fluoride en fosfaat op meer complexe matrices zoals oppervlaktewater, loogextracten, grondwater en stemflowwater. De storende waterstofcarbonaat-piek bij de bepaling van fluoride in loogextracten ko

  12. Multicolor tunability and upconversion enhancement of fluoride nanoparticles by oxygen dopant

    Science.gov (United States)

    Niu, Wenbin; Wu, Suli; Zhang, Shufen; Su, Liap Tat; Tok, Alfred Iing Yoong

    2013-08-01

    on adjusting the oxygen doping level. The synthesis of multicolored multifunctional NaGdF4:Yb,Er UCNPs was used as the model host system to demonstrate this protocol. Ammonium nitrate (NH4NO3) was used as the oxygen source and added into the reaction system at the beginning stage of nucleation and growth process of fluoride UCNPs, which facilitates the formation of enough oxygen atoms and the diffusion of these into the fluoride host matrix. The results revealed that multicolour output and upconversion enhancement mainly resulted from the variation of phonon energy and crystal field symmetry of the host lattice, respectively. This strategy can be further expanded to other fluoride host matrices. As an example of an application, multicolored UCNPs were used as a color converter in light emitting diodes, which can effectively convert near-infrared light into visible light. It is expected that these multicolored UCNPs will be promising for applications in multiplexing biodetection, bioimaging (optical and magnetic resonance imaging) and other optical technologies, and the present method for the control of O2- doping may also be used in other functional nanomaterials. Electronic supplementary information (ESI) available: Upconversion spectra of NaYF4:Yb,Er UCNPs prepared with various oxygen sources (trimethylamine N-oxide and ammonium carbonate, Fig. S1) and different addition temperatures of NH4NO3 (Fig. S2), enlarged XRD patterns (Fig. S3), the intensity ratios of green to red emissions of NaGdF4:Yb,Er UCNPs prepared with various amounts of NH4NO3 (Fig. S4), power dependence of upconversion spectra of NaGdF4:Yb,Er UCNPs prepared at 300 °C for 1 h (Fig. S5), upconversion spectra of the product after further reaction between as-prepared NaYF4:Yb,Er and 50 mg of NH4NO3 at 300 °C for 1 h (Fig. S6), XRD patterns of NaYF4:Yb,Er and NaLuF4:Yb,Er UCNPs prepared with various amounts of NH4NO3 (Fig. S7 and S8), the corresponding magnetization curves of NaGdF4:Yb,Er UCNPs (Fig

  13. Effect of sodium fluoride in maternal and offspring rats and its amelioration

    Institute of Scientific and Technical Information of China (English)

    SnehaPanchal; RamtejJ. Verma

    2014-01-01

    High fluoride content is known to cause dental and skeletal abnormalities. In addition, present review indicates that sodium fluoride consumption caused increased number of r=esorptions and dead foetuses. Various skeletal anomalies such as wavy ribs, presence of 14th ribs, lacking 6th sternebrae and incompete ossification of skull occur. All these changes could be due to oxidative stress caused by fluoride consumption. Fluoride-induced changes could be successfully ameliorated by cotreatment with vitamins and calcium.

  14. Highly Selective Fluoride Recognition by a Simple Carbazole-based Hydrozone Derivative

    Institute of Scientific and Technical Information of China (English)

    TANG Li-jun; ZHAO Guo-you; HUANG Zhen-long; WANG Nan-nan; GUO Jiao-jiao

    2013-01-01

    A simple carbazole hydrozone derivative(1) was synthesized and used as an optical probe for fluoride recognition in CH3CN.Receptor 1 exhibited colorimetric and fluorescent dual-channel response to fluoride anions.Addition of fluoride to a receptor 1 solution in CH3CN induced a distinct color change from yellow to magenta,the solution also displayed significant fluorescence blue shift.Thus receptor 1 exhibited dual-channel responses to fluoride with a high selectivity and sensitivity.

  15. Bioactivity of Sodium Free Fluoride Containing Glasses and Glass-Ceramics

    OpenAIRE

    Xiaojing Chen; Xiaohui Chen; Brauer, Delia S.; Rory M. Wilson; Hill, Robert G.; Natalia Karpukhina

    2014-01-01

    The bioactivity of a series of fluoride-containing sodium-free calcium and strontium phosphosilicate glasses has been tested in vitro. Glasses with high fluoride content were partially crystallised to apatite and other fluoride-containing phases. The bioactivity study was carried out in Tris and SBF buffers, and apatite formation was monitored by XRD, FTIR and solid state NMR. Ion release in solutions has been measured using ICP-OES and fluoride-ion selective electrode. The results show that...

  16. Effects of fluoride in drinking water on health of deciduous teeth

    OpenAIRE

    Blagojević Duška; Stojšin Ivana

    2004-01-01

    INTRODUCTION High incidence of decayed deciduous teeth, as well as lack of adequate therapy, makes tooth decay prevention very important. One of the simplest ways to reduce tooth decay is fluoridation of drinking water. The optimal concentration of fluoride in drinking water is 1 ppm/l, and many waters naturally contain this quantity. Waters in Vojvodina are mainly poor in fluoride, except in a few regions. It has long been postulated that fluoride has a prophyilactic effect during intrauteri...

  17. Batch and Column Experiments on Fluoride Removal from Waters Using Modified Zeolite

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    High fluoride groundwater occurs widely in China, presenting a quite serious environmental problem. Zeolite from Xinyang, China was tested as the fluoride-removing adsorbent. Batch and column experiments on fluoride removal using modified zeolites treated with hydrochloric acid,sodium hydroxide, sodium chloride and ferric chloride, respectively show that 0. 1 mol/L HCImodified zeolite can be used as an adsorbent for fluoride, with an adsorption capacity of 173. 16mg/kg.

  18. Effect of high fluoride concentration in drinking water on children’s intelligence

    OpenAIRE

    Seraj B.; Shahrabi M; Falahzade M; Falahzade F; Akhondi N.

    2006-01-01

    Background and Aim: Human and animal studies linking fluoride with diminished intelligence have been published. Although adverse effects of high intake of fluoride on intelligence and mental acuity continue to be reported, they are still controversial. The aim of this research was to investigate the relationship between fluoride in drinking water and children's intelligence. Materials and Methods: In this cross sectional study, 41 children were selected from the high fluoride area with 2...

  19. Kinetic Analysis of 18F-Fluoride PET Images of Breast Cancer Bone Metastases

    OpenAIRE

    Doot, Robert K; Muzi, Mark; Peterson, Lanell M.; Schubert, Erin K; Gralow, Julie R.; Specht, Jennifer M.; Mankoff, David A.

    2010-01-01

    The most common site of metastasis for breast cancer is bone. Quantitative 18F-fluoride PET can estimate the kinetics of fluoride incorporation into bone as a measure of fluoride transport, bone formation, and turnover. The purpose of this analysis was to evaluate the accuracy and precision of 18F-fluoride model parameter estimates for characterizing regional kinetics in metastases and normal bone in breast cancer patients.

  20. Absorption, distribution and excretion of inhaled hydrogen fluoride in the rat

    Energy Technology Data Exchange (ETDEWEB)

    Morris, J.B.

    1979-01-01

    Rats were subjected to whole body HF exposure for 6 hrs or to nose-only HF exposure for 1 hr. Total and/or ionic fluoride concentrations in selected tissues were determined at various times following exposure. In rats sacrificed 6 hrs after whole body exposure, dose-dependent increases in lung, plasma, and kidney total and ionic fluoride concentration occurred. Rats excreted more fluoride in the urine after whole body exposure than could be explained by the amount of HF inhaled. Considerable evidence suggests that airborne HF deposits on fur and is then ingested due to preening activity. Urinary fluoride excretion was increased by nose-only exposure. The urinary fluoride excretion accounted for approximately twice the fluoride estimated to be inhaled during exposure. Tissue fluoride concentrations were elevated immediately after nose-only exposure. Fluoride concentrations in lung and kidney returned to control levels within 12 hrs. Plasma fluoride concentration was slightly elevated 24 hrs after the start of the 1 hr exposure but was at control levels at 96 hrs. Immediately following nose-only exposure, lung ionic fluoride concentrations were less than plasma ionic fluoride concentrations suggesting that the fluoride in the lung had reached that site via plasma transport rather than by inhalation. A dose-dependent increase in plasma ionic fluoride concentration occurred after upper respiratory tract HF exposure providing strong evidence that fluoride is absorbed systemically from that site. The plasma ionic fluoride concentration after upper respiratory tract exposure was of sufficient magnitude to account for the plasma fluoride concentrations observed in intact nose-only exposed rats. (ERB)

  1. Effect of sodium fluoride in maternal and offspring rats and its amelioration

    Directory of Open Access Journals (Sweden)

    Sneha Panchal

    2014-03-01

    Full Text Available High fluoride content is known to cause dental and skeletal abnormalities. In addition, present review indicates that sodium fluoride consumption caused increased number of r=esorptions and dead foetuses. Various skeletal anomalies such as wavy ribs, presence of 14th ribs, lacking 6th sternebrae and incompete ossification of skull occur. All these changes could be due to oxidative stress caused by fluoride consumption. Fluoride-induced changes could be successfully ameliorated by cotreatment with vitamins and calcium.

  2. Fluorescent naphthalene-based benzene tripod for selective recognition of fluoride in physiological condition

    Indian Academy of Sciences (India)

    Barun kumar Datta; Chirantan Kar; Gopal Das

    2015-02-01

    Aluminium complex of a naphthalene-based benzene tripod ligand system has been reported for the selective recognition of fluoride in aqueous medium in physiological condition. The ligand can selectively recognize Al3+ through enhancement in the fluorescence intensity and this in situ formed aluminium complex recognizes fluoride through quenching of fluorescence. The receptor system detects fluoride in nanomolar range. The sensing property was extended for practical utility to sense fluoride in tap water, pond water and river water.

  3. Reducing Exposure to High Fluoride Drinking Water in Estonia—A Countrywide Study

    OpenAIRE

    Ene Indermitte; Astrid Saava; Enn Karro

    2014-01-01

    Fluoride is a naturally occurring contaminant in groundwater in Estonia. There are several regions in Estonia with fluoride contents in public water supplies as high as 7 mg/L. Long-term exposure to high-fluoride drinking water may have several adverse health effects, primarily dental fluorosis. The opportunities for exposure reduction rely highly on water treatment technologies. Since 2004 public water suppliers in Estonia have made efforts to diminish fluoride content in drinking water sys...

  4. The Effect of Acute Fluoride Poisoning on Nitric Oxide and Methemoglobin Formation in the Guinea pig

    OpenAIRE

    ŞİRELİ, Meltem

    2004-01-01

    To study the effect of acute fluoride poisoning on nitric oxide and methemoglobin formation, 250 mg/kg bw sodium fluoride was applied alone and verapamil was applied together with fluoride. Blood nitric oxide (Griess reaction) and calcium levels; hemoglobin, methemoglobin and hematocrit values; and erythrocyte counts were determined and compared with those of the controls. After the fluoride application it was found that there was a relative relationship between the increase in nitric oxide a...

  5. The Karlsruhe 4π barium fluoride detector

    International Nuclear Information System (INIS)

    A new experimental approach has been implemented for accurate measurements of neutron capture cross sections in the energy range from 5 to 200 keV. The Karlsruhe 4π Barium Fluoride Detector consists of 42 crystals shaped as hexagonal and pentagonal truncated pyramids forming a spherical shell with 10 cm inner radius and 15 cm thickness. All crystals are supplied with reflector and photomultiplier, thus representing independent gamma-ray detectors. Each detector module covers the same solid angle with respect to a gamma-ray source located in the centre. The energy resolution of the 4π detector is 14% at 662 keV and 7% at 2.5 MeV gamma-ray energy, the overall time reslution is 500 ps and the peak efficiency 90% at 1 MeV. The detector allows to register capture cascades with 95% probability above a threshold energy of 2.5 MeV in the sum energy spectrum. Neutrons are produced via the 7Li(p,n)7Be reaction using the pulsed proton beam of a Van de Graaff accelerator. The neutron spectrum can be taylored according to the experimental requirements in an energy range from 5 to 200 keV by choosing appropriate proton energies. A collimated neutron beam is passing through the detector and hits the sample in the centre. The energy of captured neutrons is determined via time of flight, the primary flight path being 77 cm. The combination of short primary flight path, a 10 cm inner radius of the spherical BaF2 shell, and the low capture cross section of barium allows to discriminate background due to capture of sample scattered neutrons in the scintillator by time of flight, leaving part of the neutron energy range completely undisturbed. (orig./HSI)

  6. Risk Assessment of Fluoride Intake from Tea in the Republic of Ireland and its Implications for Public Health and Water Fluoridation

    Science.gov (United States)

    Waugh, Declan T.; Potter, William; Limeback, Hardy; Godfrey, Michael

    2016-01-01

    The Republic of Ireland (RoI) is the only European Country with a mandatory national legislation requiring artificial fluoridation of drinking water and has the highest per capita consumption of black tea in the world. Tea is a hyperaccumulator of fluoride and chronic fluoride intake is associated with multiple negative health outcomes. In this study, fifty four brands of the commercially available black tea bag products were purchased and the fluoride level in tea infusions tested by an ion-selective electrode method. The fluoride content in all brands tested ranged from 1.6 to 6.1 mg/L, with a mean value of 3.3 mg/L. According to our risk assessment it is evident that the general population in the RoI is at a high risk of chronic fluoride exposure and associated adverse health effects based on established reference values. We conclude that the culture of habitual tea drinking in the RoI indicates that the total cumulative dietary fluoride intake in the general population could readily exceed the levels known to cause chronic fluoride intoxication. Evidence suggests that excessive fluoride intake may be contributing to a wide range of adverse health effects. Therefore from a public health perspective, it would seem prudent and sensible that risk reduction measures be implemented to reduce the total body burden of fluoride in the population. PMID:26927146

  7. Risk Assessment of Fluoride Intake from Tea in the Republic of Ireland and its Implications for Public Health and Water Fluoridation.

    Science.gov (United States)

    Waugh, Declan T; Potter, William; Limeback, Hardy; Godfrey, Michael

    2016-03-01

    The Republic of Ireland (RoI) is the only European Country with a mandatory national legislation requiring artificial fluoridation of drinking water and has the highest per capita consumption of black tea in the world. Tea is a hyperaccumulator of fluoride and chronic fluoride intake is associated with multiple negative health outcomes. In this study, fifty four brands of the commercially available black tea bag products were purchased and the fluoride level in tea infusions tested by an ion-selective electrode method. The fluoride content in all brands tested ranged from 1.6 to 6.1 mg/L, with a mean value of 3.3 mg/L. According to our risk assessment it is evident that the general population in the RoI is at a high risk of chronic fluoride exposure and associated adverse health effects based on established reference values. We conclude that the culture of habitual tea drinking in the RoI indicates that the total cumulative dietary fluoride intake in the general population could readily exceed the levels known to cause chronic fluoride intoxication. Evidence suggests that excessive fluoride intake may be contributing to a wide range of adverse health effects. Therefore from a public health perspective, it would seem prudent and sensible that risk reduction measures be implemented to reduce the total body burden of fluoride in the population. PMID:26927146

  8. Antimicrobial and fluoride release capacity of orthodontic bonding materials

    Directory of Open Access Journals (Sweden)

    Erika Machado Caldeira

    2013-07-01

    Full Text Available OBJECTIVE: The aim of this study was to evaluate the antimicrobial and fluoride releasing capacity of 3 bonding materials. MATERIAL AND METHODS: Thirty nine specimens with standardized surface smoothness and dimensions were prepared. The antimicrobial capacity of the materials against S. mutans, L. casei and C. albicans was evaluated by determining the percentage of growth inhibition of these microorganisms in an inoculated medium, obtained by optical density readouts on a spectrophotometer. The potential to interfere in microbial growth on the surface of the studied materials was observed by means of scanning electron microscopy (SEM. The fluoride release capacity in ultrapure water for 14 days was analyzed by means of ion chromatography. RESULTS: The PLUS group presented the highest percentage of microbial inhibition and the most contamination-free surface. The FUJI group presented the best fluoride release capacity. CONCLUSIONS: The TransbondTM Plus Color Change was the one that presented the best general behavior considering the evaluated aspects.

  9. Influence of milk products on fluoride bioavailability in man.

    Science.gov (United States)

    Ekstrand, J; Ehrnebo, M

    1979-09-01

    The effect of milk products on the gastrointestinal absorption of fluoride from sodium fluoride tablets was studied in five healthy subjects. Two different diets were tested: (1) 250 ml standardized milk (3% fat) and (2) 500 ml of milk, 3 pieces of white bread with cheese and 150 ml of yoghurt. The 100% bioavailability of sodium fluoride tablets during fasting was greatly decreased by coadministration of milk products: with Diet 1 the absolute bioavailability calculated from combined plasma and urine data was in the range 50--79% and with Diet 2 it ranged from 50--71%. It is suggested that the decreased bioavailability produced by dairy products should be taken into account when establishing flouride dosage regimens for prophylaxis of caries.

  10. Liquid Fluoride Salt Experimentation Using a Small Natural Circulation Cell

    Energy Technology Data Exchange (ETDEWEB)

    Yoder Jr, Graydon L [ORNL; Heatherly, Dennis Wayne [ORNL; Williams, David F [ORNL; Elkassabgi, Yousri M. [Texas A& M University, Kingsville; Caja, Joseph [Electrochemical Systems, Inc.; Caja, Mario [ORNL; Jordan, John [Texas A& M University, Kingsville; Salinas, Roberto [Texas A& M University, Kingsville

    2014-04-01

    A small molten fluoride salt experiment has been constructed and tested to develop experimental techniques for application in liquid fluoride salt systems. There were five major objectives in developing this test apparatus: Allow visual observation of the salt during testing (how can lighting be introduced, how can pictures be taken, what can be seen) Determine if IR photography can be used to examine components submerged in the salt Determine if the experimental configuration provides salt velocity sufficient for collection of corrosion data for future experimentation Determine if a laser Doppler velocimeter can be used to quantify salt velocities. Acquire natural circulation heat transfer data in fluoride salt at temperatures up to 700oC All of these objectives were successfully achieved during testing with the exception of the fourth: acquiring velocity data using the laser Doppler velocimeter. This paper describes the experiment and experimental techniques used, and presents data taken during natural circulation testing.

  11. Total and free fluoride in toothpastes from some non-established market economy countries.

    NARCIS (Netherlands)

    Loveren, C. van; Moorer, W.R.; Buijs, M.J.; Palenstein Helderman, W.H. van

    2005-01-01

    In 101 fluoride toothpastes, bought in local shops in Burkina Faso (n = 3), China (n = 5), Myanmar (n = 22), Nepal (n = 19), Philippines (n = 13), Syria (n = 22), Togo (n = 7) and Vietnam (n = 10), the total and free ionisable fluoride concentrations were established. The total fluoride concentratio

  12. 76 FR 19001 - Sulfuryl Fluoride; Addendum to Proposed Order Granting Objections to Tolerances and Denying...

    Science.gov (United States)

    2011-04-06

    ... the Proposed Order On January 19, 2011 (76 FR 3422, Jan. 19, 2011), EPA issued a proposed order... AGENCY 40 CFR Part 180 Sulfuryl Fluoride; Addendum to Proposed Order Granting Objections to Tolerances... supplementing its proposed order published January 19, 2011, regarding sulfuryl fluoride and fluoride...

  13. 40 CFR 142.61 - Variances from the maximum contaminant level for fluoride.

    Science.gov (United States)

    2010-07-01

    ... level for fluoride. 142.61 Section 142.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... from the maximum contaminant level for fluoride. (a) The Administrator, pursuant to section 1415(a)(1... means generally available for achieving compliance with the Maximum Contaminant Level for fluoride....

  14. 40 CFR 415.230 - Applicability; description of the aluminum fluoride production subcategory.

    Science.gov (United States)

    2010-07-01

    ... aluminum fluoride production subcategory. 415.230 Section 415.230 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Aluminum Fluoride Production Subcategory § 415.230 Applicability; description of the aluminum fluoride production subcategory. This subpart applies to discharges to waters of the United...

  15. 40 CFR 415.550 - Applicability; description of the sodium fluoride production subcategory.

    Science.gov (United States)

    2010-07-01

    ... sodium fluoride production subcategory. 415.550 Section 415.550 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Sodium Fluoride Production Subcategory § 415.550 Applicability; description of the sodium fluoride production subcategory. The provisions of this subpart are applicable to discharges and to...

  16. A method for producing controlled fluoride release from an orthodontic bracket.

    Science.gov (United States)

    Li, Song; Hobson, Ross S; Bai, Yuxing; Yan, Zhuoqun; Carrick, Thomas E; McCabe, John F

    2007-12-01

    The aim of this study was to manufacture and test, in vitro, a novel modification to provide fluoride-releasing orthodontic brackets. Thirty-two orthodontic brackets were drilled to produce a recess (approximately 1.3 mm in diameter and 0.7 mm in depth) at the centre of the bracket base. Four materials, with and without the addition of sodium fluoride, a glass ionomer cement (Ketac Cem micro), a resin-modified glass ionomer cement (RMGIC; GC Fuji Ortho LC), a zinc phosphate (Zinc Cement Improved), and a resin (Transbond XT) were used to fill the recess in the bracket base. Fluoride release was measured daily during the first week and then weekly for 10 weeks. An ion chromatograph with suppressed conductivity was used for free fluoride ion determination. Statistical analysis to determine the amount of flouride release was undertaken using analysis of variance and Tukey's test. During the first 2 weeks, the resin group, with the addition of 38 per cent sodium fluoride added, released significantly more free fluoride (P < 0.05), but after 2 weeks the fluoride release markedly decreased. After 5 weeks, the RMGIC group, with 15 per cent added sodium fluoride, had significantly higher (P < 0.05) daily fluoride release than the other groups. The findings demonstrated that an appropriate fluoridated material can be used as a fluoride-releasing reservoir in a modified orthodontic bracket to enable it to release fluoride over the period of fixed appliance treatment.

  17. Professionally applied fluoride gel in low-caries 10.5-year-olds.

    NARCIS (Netherlands)

    Truin, G.J.; Hof, M.A. van 't

    2005-01-01

    The question has been raised whether low-caries children regularly using fluoride toothpaste will benefit from the professional application of additional fluoride gel. To investigate the caries-reducing effect of semi-annually-applied neutral 1% sodium fluoride gel, we carried out a double-blind ran

  18. Environmental characteristics of regional groundwater in relation to fluoride poisoning in North China

    Science.gov (United States)

    Liu, Yong; Zhu, Wan Hua

    1991-07-01

    More and more data indicated that high- or low-fluoride-bearing drinking water led to endemic diseases in which fluoride poisoning was caused by high levels of fluoride (fluoride ion content >1.0 mg/I) in drinking water. Fluoride poisoning in North China is characterized by pathological changes of bones and teeth. Much attention has been devoted to the study of fluoride-bearing groundwater in North China because regionally groundwater has been the main source of water supply, and fluoride poisoning has developed to the extent that it affects human health seriously. Results from the studies in North China summarized in this article indicate that regional high-fluoride-bearing groundwater has a regular distribution corresponding with the development of endemic fluoride poisoning and has something to do with paleogeographic and paleoclimatic conditions, geology, and hydrogeology, especially with types of hydrogeochemistry, pH value of groundwater, degree of mineralization, and so forth. High-fluoride-bearing groundwater in relation to fluorosis occurs mainly in North China, and many effective measures have been taken to reduce the fluoride content in drinking water and to cure the disease after analyzing the distribution and environmental characteristics of high-fluoride-bearing groundwater.

  19. Contemporary perspective on the use of fluoride products in caries prevention

    NARCIS (Netherlands)

    J.M. ten Cate

    2013-01-01

    Dental caries has declined in the 40 years since fluoridated toothpastes were introduced. Much has been learned about why fluoride is so effective and how this knowledge can be used to optimise programmes for caries prevention. Fluoride works through enhancing the remineralisation of early stages of

  20. Fluoride Consumption and Its Impact on Oral Health

    Directory of Open Access Journals (Sweden)

    Luis Fernando Jacinto-Alemán

    2011-01-01

    Full Text Available Objective. The purpose of this study was to evaluate caries and dental fluorosis among Mexican preschoolers and school-aged children in a non-endemic zone for fluorosis and to measure its biological indicators. Methods. DMFT, DMFS, dmft, dmfs, and CDI indexes were applied. Fluoride urinary excretion and fluoride concentrations in home water, table salt, bottled water, bottled drinks, and toothpaste were determined. Results. Schoolchildren presented fluorosis (CDI = 0.96 and dental caries (DMFT = 2.64 and DMFS = 3.97. Preschoolers presented dmft = 4.85 and dmfs = 8.80. DMFT and DMFS were lower in children with mild to moderate dental fluorosis (DF. Variable fluoride concentrations were found in the analyzed products (home water = 0.18–0.44 ppm F, table salt = 0–485 ppm F, bottled water = 0.18–0.47 ppm F, juices = 0.08–1.42 ppm F, nectars = 0.07–1.30 ppm F, bottled drinks = 0.10–1.70 ppm F, toothpaste = 0–2,053 ppm F. Mean daily fluoride excretion was 422 ± 176 µg/24 h for schoolchildren and 367 ± 150 µg/24 h for preschoolers. Conclusions. Data from our study show that, despite values of excretion within an optimal fluoride intake range, the prevalence of caries was significant in both groups, and 60% of the 11- to 12-year-old children presented with dental fluorosis. In addition, variable fluoride concentrations in products frequently consumed by children were found.

  1. Fluoride Consumption and Its Impact on Oral Health

    Science.gov (United States)

    Jiménez-Farfán, María Dolores; Hernández-Guerrero, Juan Carlos; Juárez-López, Lilia Adriana; Jacinto-Alemán, Luis Fernando; de la Fuente-Hernández, Javier

    2011-01-01

    Objective The purpose of this study was to evaluate caries and dental fluorosis among Mexican preschoolers and school-aged children in a non-endemic zone for fluorosis and to measure its biological indicators. Methods DMFT, DMFS, dmft, dmfs, and CDI indexes were applied. Fluoride urinary excretion and fluoride concentrations in home water, table salt, bottled water, bottled drinks, and toothpaste were determined. Results Schoolchildren presented fluorosis (CDI = 0.96) and dental caries (DMFT = 2.64 and DMFS = 3.97). Preschoolers presented dmft = 4.85 and dmfs = 8.80. DMFT and DMFS were lower in children with mild to moderate dental fluorosis (DF). Variable fluoride concentrations were found in the analyzed products (home water = 0.18–0.44 ppm F, table salt = 0–485 ppm F, bottled water = 0.18–0.47 ppm F, juices = 0.08–1.42 ppm F, nectars = 0.07–1.30 ppm F, bottled drinks = 0.10–1.70 ppm F, toothpaste = 0–2,053 ppm F). Mean daily fluoride excretion was 422 ± 176 μg/24 h for schoolchildren and 367 ± 150 μg/24 h for preschoolers. Conclusions Data from our study show that, despite values of excretion within an optimal fluoride intake range, the prevalence of caries was significant in both groups, and 60% of the 11- to 12-year-old children presented with dental fluorosis. In addition, variable fluoride concentrations in products frequently consumed by children were found. PMID:21318021

  2. {sup 11}C-methylations using {sup 11}C-methyl iodide and tetrabutylammonium fluoride

    Energy Technology Data Exchange (ETDEWEB)

    Adam, M.J.; Jivan, S.; Huser, J.M.; Lu, J. [TRIUMF Univ. of British Columbia, Vancouver (Canada)

    2000-07-01

    Carbon-11 methylation reactions on functional groups such as phenols and amides require a base when using {sup 11}C-methyl iodide. This study demonstrates that tetrabutylammonium fluoride (TBAF) can be used as a base to prepare {sup 11}C-radiopharmaceuticals efficiently and in high yield. We have applied this method to raclopride, methylphenidate, PK11195, dihydrotetrabenazine and MDL100907 and have compared the results with the Alumina/KF and hydroxide methods. Our results indicate that TBAF gives equivalent or higher radiochemical yields compared to the other bases even when using as little as 200 {mu}g of precursor. In the case of PK11195 the TBAF method was the only one that provided a reasonable yield of product. (orig.)

  3. Vacuum Ultraviolet Field Emission Lamp Consisting of Neodymium Ion Doped Lutetium Fluoride Thin Film as Phosphor

    Directory of Open Access Journals (Sweden)

    Masahiro Yanagihara

    2014-01-01

    Full Text Available A vacuum ultraviolet (VUV field emission lamp was developed by using a neodymium ion doped lutetium fluoride (Nd3+ : LuF3 thin film as solid-state phosphor and carbon nanofiber field electron emitters. The thin film was synthesized by pulsed laser deposition and incorporated into the lamp. The cathodoluminescence spectra of the lamp showed multiple emission peaks at 180, 225, and 255 nm. These emission spectra were in good agreement with the spectra reported for the Nd3+ : LuF3 crystal. Moreover, application of an acceleration voltage effectively increased the emission intensity. These results contribute to the performance enhancement of the lamp operating in the VUV region.

  4. Stimulated Raman scattering in soft glass fluoride fibers

    DEFF Research Database (Denmark)

    Petersen, Christian; Dupont, Sune Vestergaard Lund; Agger, Christian;

    2011-01-01

    We have measured the absolute Raman gain spectrum in short fluoride soft glass fibers with a pump wavelength of 1650 nm. We found a peak gain of gR=4.0±2×10−14 m W−1.......We have measured the absolute Raman gain spectrum in short fluoride soft glass fibers with a pump wavelength of 1650 nm. We found a peak gain of gR=4.0±2×10−14 m W−1....

  5. The dissolution of kaolin by acidic fluoride wastes

    DEFF Research Database (Denmark)

    Kau, P. M. H.; Smith, D. W.; Binning, Philip John

    1997-01-01

    The potential use of kaolin as a lining material for the storage of acidic and acidic fluoride wastes is investigated, No significant changes are observed gravimetrically or structurally for kaolin soaked under acidic conditions down to pH 2 for periods up to 90 days, Some release of aluminium...... was noted with decreasing pH, Severe kaolin dissolution was apparent, however, when soaked in solutions less than pH 3 to 4 with a fluoride concentration of 0.05 M. Aluminium-oxygen bonding in kaolin appears to be substantially more prone to hydrofluoric acid attack than does silicon-oxygen bonding...

  6. Stimulated Raman scattering in soft glass fluoride fibers

    DEFF Research Database (Denmark)

    Petersen, Christian; Dupont, Sune; Agger, Christian;

    2011-01-01

    We have measured the absolute Raman gain spectrum in short fluoride soft glass fibers with a pump wavelength of 1650nm. We found a peak gain of gR ¼ 4:0 2 × 10−14mW−1.......We have measured the absolute Raman gain spectrum in short fluoride soft glass fibers with a pump wavelength of 1650nm. We found a peak gain of gR ¼ 4:0 2 × 10−14mW−1....

  7. Investigation of In Vitro Effects of Fluoride on Bovine Sperm

    OpenAIRE

    TANYILDIZI, Sadettin

    2002-01-01

    The in vitro effects of various concentrations of sodium fluoride on the percentages of motile spermatozoa and abnormal spermatozoa with the hyaluronidase activities of semen were investigated. Holstein bulls (n=20), aged between 4 and 5 years, were used in this study. The semen samples obtained from all animals were divided into five parts and one of them was used as the control sample. Sodium fluoride solutions were prepared at concentrations of 30, 60, 120 and 240mM and then these solutio...

  8. Thermoluminescent lithium fluorides dosemeters in personnel monitoring in the GDR

    International Nuclear Information System (INIS)

    Described are thermoluminescent (TL) dosemeters of lithium fluoride used in centralized personnel monitoring in the GDR. Results of large-scale experiment are presented to compare the accuracy of readings of lithium fluoride or teflon dosemeter and that of film dosemeters. 332 persons were controlled for the experiment. A phantom was irradiated simultaneously by X and gamma radiation. The experience in application of thermoluminescent dosemeters to personnel monitoring of radiation load of a whole body and body parts using rings is described. Two Types of TL ring dosemeters for measuring X, gamma and deta radiations are presented. Advantage and shortcomings of TL dosemeters are noted

  9. In vitro remineralizing effect of fluoride varnishes containing sodium trimetaphosphate.

    Science.gov (United States)

    Manarelli, M M; Delbem, A C B; Lima, T M T; Castilho, F C N; Pessan, J P

    2014-01-01

    This study analyzed the effects of fluoride varnishes supplemented with sodium trimetaphosphate (TMP) on the remineralization of caries-like lesions in vitro. Bovine enamel discs were selected through surface hardness (SH) and caries-like lesions were induced. SH was again determined and the blocks were divided into 7 experimental groups (n = 24/group): placebo (no fluoride or TMP), 5% TMP, 2.5% NaF, 2.5% NaF/5% TMP, 5% NaF, 5% NaF/5% TMP and commercial formulation (Duraphat™, 5% NaF), following a blind protocol. Discs were treated with the varnishes and kept in a remineralizing solution for 4 h and a demineralizing solution for 2 h. Varnishes were then removed and half of the discs were used for analysis of loosely (CaF2) and firmly bound fluoride. The remaining discs were submitted to a pH-cycling regimen for 6 days. The percentage of surface hardness recovery (%SHR), cross-sectional hardness (ΔKHN) and enamel CaF2 and fluoride were determined. Data were analyzed by ANOVA and by Student-Newman-Keuls' test (p < 0.05). A dose-response relationship was observed between fluoride concentrations in the varnishes and %SHR. The 5% TMP varnish led to %SHR similar to that obtained for the placebo. When TMP was used in association with fluoride, however, significantly higher %SHR were observed in comparison with their counterparts without TMP. Moreover, ΔKHN obtained for the 5% NaF/5% TMP was significantly lower among all groups tested. Higher concentrations of CaF2 and fluoride were observed for Duraphat and 5% NaF, followed by 5% NaF/5% TMP, 2.5% NaF and 2.5% NaF/5% TMP (p < 0.05). It was concluded that the supplementation of fluoride varnishes with TMP leads to enhanced remineralizing effect of artificial caries lesions in vitro. PMID:24526110

  10. Dutch fluoride concentration in perspective; Nederlandse fluoridenconcentratie in perspectief

    Energy Technology Data Exchange (ETDEWEB)

    Hoekstra, B. [Tauw, Deventer (Netherlands); Van Dijk, C. [Wageningen UR, Wageningen (Netherlands); Van Doorn, W. [Royal Haskoning, Nijmegen (Netherlands)

    2009-08-15

    Recent jurisprudence shows that in grant permitting the non legal aspects of air quality requirements for fluorides should be expressly taken into account. During the decision-making process careful considerations should be made about emissions, background concentrations and possible effects of fluorides [mk]. [Dutch] Uit recente jurisprudentie is gebleken dat bij vergunningverlening nadrukkelijk rekening moet worden gehouden met de niet-wettelijke luchtkwaliteitseisen voor fluoriden. Bij besluitvorming dient een zorgvuldige afweging en motivering plaats te vinden over emissies, achtergrondconcentraties en mogelijke effecten van fluoriden.

  11. Recovery of protactinium from molten fluoride nuclear fuel compositions

    Science.gov (United States)

    Baes, C.F. Jr.; Bamberger, C.; Ross, R.G.

    1973-12-25

    A method is provided for separating protactinium from a molten fluonlde salt composition consisting essentially of at least one alkali and alkaline earth metal fluoride and at least one soluble fluoride of uranium or thorium which comprises oxidizing the protactinium in said composition to the + 5 oxidation state and contacting said composition with an oxide selected from the group consisting of an alkali metal oxide, an alkaline earth oxide, thorium oxide, and uranium oxide, and thereafter isolating the resultant insoluble protactinium oxide product from said composition. (Official Gazette)

  12. Study by thermochromatography of fluorides of transuranium elements

    International Nuclear Information System (INIS)

    Thermochromatography was made suitable for fluoride study. So, an investigation of actinide tetrafluorides was accomplished from uranium to californium. Pentavalent and hexavalent fluorospecies of uranium, neptunium, plutonium and ruthenium were studied. Some new compounds have been identified in gaseous phase, whose: PuF5, PuOF3 and PaOF3. Furthermore, some presomptions as for the existence in gaseous phase of EsF4 and of an heptavalent fluorospecies of plutonium have been established. An important analogy between plutonium and ruthenium behaviour with fluorine have been shown, these results could explain the difficulties encountered in the fluoride-volatility processes

  13. Fluoride and sodium trimetaphosphate (TMP) release from fluoride varnishes supplemented with TMP.

    Science.gov (United States)

    Manarelli, Michele Mauricio; Delbem, Alberto Carlos Botazzo; Percinoto, Célio; Pessan, Juliano Pelim

    2016-05-20

    This study assessed fluoride (F) and sodium trimetaphosphate (TMP) release into artificial saliva from varnishes containing 0%, 2.5%, and 5% NaF, supplemented or not with 5% TMP. The varnishes were applied on polyester sheets (n = 8/group), and F and TMP released into artificial saliva were measured for up to 24 hours. The amount of F and TMP released were directly related to NaF and TMP concentrations in the varnishes. The highest F release was seen for 5% NaF and 5% NaF + 5% TMP, whereas 5% TMP released the highest amount of TMP. However, the simultaneous addition of NaF and TMP to varnishes significantly reduced the amount of F and TMP released from the products. PMID:27223137

  14. Fluoride and sodium trimetaphosphate (TMP release from fluoride varnishes supplemented with TMP

    Directory of Open Access Journals (Sweden)

    Michele Mauricio MANARELLI

    2016-01-01

    Full Text Available Abstract This study assessed fluoride (F and sodium trimetaphosphate (TMP release into artificial saliva from varnishes containing 0%, 2.5%, and 5% NaF, supplemented or not with 5% TMP. The varnishes were applied on polyester sheets (n = 8/group, and F and TMP released into artificial saliva were measured for up to 24 hours. The amount of F and TMP released were directly related to NaF and TMP concentrations in the varnishes. The highest F release was seen for 5% NaF and 5% NaF + 5% TMP, whereas 5% TMP released the highest amount of TMP. However, the simultaneous addition of NaF and TMP to varnishes significantly reduced the amount of F and TMP released from the products.

  15. Fluoride rinse effect on retention of CaF2 formed on enamel/dentine by fluoride application

    Directory of Open Access Journals (Sweden)

    Amanda FALCÃO

    2016-01-01

    Full Text Available Abstract Calcium fluoride-like materials (“CaF2” formed on dental surfaces after professional fluoride application are unstable in the oral environment but can be retained longer with a daily NaF mouthrinse. We tested the effect of twice daily 0.05% NaF rinses on the retention of “CaF2” formed on enamel and dentine after applying acidulated phosphate fluoride (APF. “CaF2” formed on enamel/dentine by APF application significantly decreased after exposure to artificial saliva and the 0.05% NaF rinse was ineffective to avoid this reduction. These findings suggest that the combination of APF and 0.05% NaF is not clinically relevant, either for caries or dental hypersensitivity.

  16. Fluoride rinse effect on retention of CaF2 formed on enamel/dentine by fluoride application.

    Science.gov (United States)

    Falcão, Amanda; Masson, Nadia; Leitão, Tarcísio Jorge; Botelho, Juliana Nunes; Ferreira-Nóbilo, Naiara de Paula; Tabchoury, Cínthia Pereira Machado; Tenuta, Livia Maria Andaló; Cury, Jaime Aparecido

    2016-01-01

    Calcium fluoride-like materials ("CaF2") formed on dental surfaces after professional fluoride application are unstable in the oral environment but can be retained longer with a daily NaF mouthrinse. We tested the effect of twice daily 0.05% NaF rinses on the retention of "CaF2" formed on enamel and dentine after applying acidulated phosphate fluoride (APF). "CaF2" formed on enamel/dentine by APF application significantly decreased after exposure to artificial saliva and the 0.05% NaF rinse was ineffective to avoid this reduction. These findings suggest that the combination of APF and 0.05% NaF is not clinically relevant, either for caries or dental hypersensitivity. PMID:27050937

  17. Ion-assisted deposition of yttrium fluoride as a substitute for thorium fluoride: application to infrared antireflection coating on germanium

    Science.gov (United States)

    Robic, Jean-Yves; Rolland, Bernard; Deutsch, Jean-Claude; Gallais, Patrick

    1994-11-01

    Yttrium fluoride has been proposed as a substitute for thorium fluoride in anti-reflection coatings for the infrared range. We have studied the ion assisted deposition (IAD) of YF3 in order to obtain dense and low absorbency layers in the 8 to 12 mm spectral window. Refractive index and extinction coefficient of this fluoride were determined from spectrophotometry measurements. We have then associated the YF3 with ZnS and Ge layers so as to obtain four layer anti-reflection coatings on germanium. The stress induced by each layer in the coating was measured and the sum was shown to be equal to the stress of the total coating. Eventually, an industrial, high efficiency, both side anti-reflection coating on germanium was developed using IAD YF3 film.

  18. EFFECT OF DAILY FLUORIDE EXPOSURE ON FLUORIDE RELEASE BY HIGH STRENGTH GLASS IONOMER RESTORATIVE MATERIAL USED WITH ATRAUMATIC RESTORATIVE TECHNIQUE: AN IN VITRO STUDY

    Directory of Open Access Journals (Sweden)

    Hegde Mithra N.

    2012-04-01

    Full Text Available An in-vitro study was done to evaluate the effect of fluoride exposure, fluoride release and recharging capability by High strength Glass Ionomer restorative material used with Atraumatic restorative technique. 20 specimens were divided into four groups of five specimens each. The results showed that High strength Glass ionomer cements (Fuji IX release fluoride, the greatest release takes place between 24- 48 hours.High viscous High Strength Glass ionomer cements have the ability to recharge by external sources like fluoridated dentifrices and varnishes and thus acts as a fluoride reservoir. The recommendation that individuals with a high caries rate and glass ionomer restoration should have fluoride treatment with dentifrice and varnish seems appropriate.

  19. The mechanism for production of beryllium fluoride from the product of ammonium fluoride processing of beryllium- containing raw material

    Science.gov (United States)

    Kraydenko, R. I.; Dyachenko, A. N.; Malyutin, L. N.; Petlin, I. V.

    2016-06-01

    The technique of fluorite-phenacite-bertrandite ores from Russian Ermakovskoe deposit processing by ammonium bifluoride is described. To determine the temperature mode and the thermal dissociation mechanism of ammonium tetrafluoroberyllate (the product of ammonium-fluoride leaching of the ore) the TG/DTA have been carried out. By IR spectroscopy and XRD the semi-products of ammonium tetrafluoroberyllate thermal dissociation have been identified. The hygroscopic low-temperature beryllium fluoride forms higher than 380°C. The less hydroscopic form of BeF2 have been produced at 600°C.

  20. Sustainable approach for recycling waste lamb and chicken bones for fluoride removal from water followed by reusing fluoride-bearing waste in concrete.

    Science.gov (United States)

    Ismail, Zainab Z; AbdelKareem, Hala N

    2015-11-01

    Sustainable management of waste materials is an attractive approach for modern societies. In this study, recycling of raw waste lamb and chicken bones for defluoridation of water has been estimated. The effects of several experimental parameters including contact time, pH, bone dose, fluoride initial concentration, bone grains size, agitation rate, and the effect of co-existing anions in actual samples of wastewater were studied for fluoride removal from aqueous solutions. Results indicated excellent fluoride removal efficiency up to 99.4% and 99.8% using lamb and chicken bones, respectively at fluoride initial concentration of 10 mg F/L and 120 min contact time. Maximum fluoride uptake was obtained at neutral pH range 6-7. Fluoride removal kinetic was well described by the pseudo-second order kinetic model. Both, Langmuir and Freundlich isotherm models could fit the experimental data well with correlation coefficient values >0.99 suggesting favorable conditions of the process. Furthermore, for complete sustainable management of waste bones, the resulted fluoride-bearing sludge was reused in concrete mixes to partially replace sand. Tests of the mechanical properties of fluoride sludge-modified concrete mixes indicated a potential environmentally friendly approach to dispose fluoride sludge in concrete and simultaneously enhance concrete properties. PMID:26162903

  1. Fluoride rechargability of a non-resin auto-cured glass ionomer cement from a fluoridated dentifrice: An in vitro study

    Directory of Open Access Journals (Sweden)

    A Rao

    2011-01-01

    Full Text Available Background: In addition to their fluoride-releasing properties, glass ionomer cement (GICs have the ability to reuptake and release fluorides from commonly used sources like fluoridated dentifrices. This property has the potential to provide a continuous low concentration of fluoride in the saliva aiding in caries prevention. The superior fluoride-recharging abilities of resin-modified GICs over conventional GICs have been documented. The manufacturer of a non-resin, auto-cured GIC (GC Fuji VII claims fluoride release from the product to be about six times that of conventional GIC. It was hypothesized that perhaps this high fluoride release could translate into a high reuptake and release, when exposed to a 1 000 ppm fluoridated dentifrice every day, thus providing increased fluoride levels in saliva. Aims: This study therefore examined fluoride-recharging abilities of the non-resin, auto-cured glass ionomer cement from a 1 000 ppm fluoridated dentifrice and compared it with resin-modified glass ionomer cement. Materials and Methods: Twelve glass ionomer discs each of resin-modified glass ionomer cement (GC Fuji II L C, Group 1 and the non-resin, auto-cured glass ionomer cement (GC Fuji VII, Group 2 were prepared with precise dimensions of 9 x 2 mm. The 12 specimens in each group were further subdivided into two subgroups of six each. Subgroup A involved no fluoride treatment (Control. Subgroup B involved application of a 1 000 ppm dentifrice for 2 minutes twice daily with a soft toothbrush. The disc-specimens were then suspended in airtight plastic bottles containing exactly 20 ml double distilled water. The fluoride concentration of the water in which the specimen discs were immersed was measured by means of a fluoride ion selective electrode connected to an ion selective electrode meter/digital ion analyzer at 1, 2, 7, 15, and 30 days. Statistical Analysis: It was performed using the Kruskal-Wallis Test. Results and Conclusion: Fuji VII

  2. Sustainable approach for recycling waste lamb and chicken bones for fluoride removal from water followed by reusing fluoride-bearing waste in concrete.

    Science.gov (United States)

    Ismail, Zainab Z; AbdelKareem, Hala N

    2015-11-01

    Sustainable management of waste materials is an attractive approach for modern societies. In this study, recycling of raw waste lamb and chicken bones for defluoridation of water has been estimated. The effects of several experimental parameters including contact time, pH, bone dose, fluoride initial concentration, bone grains size, agitation rate, and the effect of co-existing anions in actual samples of wastewater were studied for fluoride removal from aqueous solutions. Results indicated excellent fluoride removal efficiency up to 99.4% and 99.8% using lamb and chicken bones, respectively at fluoride initial concentration of 10 mg F/L and 120 min contact time. Maximum fluoride uptake was obtained at neutral pH range 6-7. Fluoride removal kinetic was well described by the pseudo-second order kinetic model. Both, Langmuir and Freundlich isotherm models could fit the experimental data well with correlation coefficient values >0.99 suggesting favorable conditions of the process. Furthermore, for complete sustainable management of waste bones, the resulted fluoride-bearing sludge was reused in concrete mixes to partially replace sand. Tests of the mechanical properties of fluoride sludge-modified concrete mixes indicated a potential environmentally friendly approach to dispose fluoride sludge in concrete and simultaneously enhance concrete properties.

  3. Evaluation and modeling of the parameters affecting fluoride toxicity level in aquatic environments by bioassay method

    Directory of Open Access Journals (Sweden)

    Hamid Reza Shamsollahi

    2014-04-01

    Full Text Available Background: Fluoride exists in various forms in nature and water resources. , The rising level of fluoride in water resources due to discharge of industrial effluents can cause toxicity in aquatic organisms. To prevent toxicity, it is necessary to determine maximum fluoride toxicity as well as effluent discharge limits. The aim of this study was to determine the maximum fluoride toxicity and the factors affecting fluoride toxicity to provide a model in order to determine the effluent discharge limits. Methods: Daphnia magna bioassay in the absence of confounding factors was used to determine the maximum level of fluoride toxicity. Then, bioassay was repeated in the presence of the confounding factors (hardness, temperature and exposure time to determine their effects. Results: In the absence of intervening factors, fluoride LC50 levels determined after 24, 48 and 72 hours exposure were 4.9, 46.5 and 38.7 mg/l, respectively.. Also, the influence of confounding factors on LC50 values was reported significant by Minitab software. Conclusion: Increasing the water hardness reduced fluoride toxicity, and increasing the water temperature and exposure time increased fluoride toxicity in aquatic environments. Therefore, while determining the wastewater discharge limit in terms of fluoride concentration, it is essential to take the effect of confounding factors on fluoride toxicity into account in order to prevent toxicity in the open water resources.

  4. The effect of different fluoride application methods on the remineralization of initial carious lesions

    Science.gov (United States)

    2016-01-01

    Objectives The purpose of this study was to assess the effect of single and combined applications of fluoride on the amount of fluoride release, and the remineralization and physical properties of enamel. Materials and Methods Each of four fluoride varnish and gel products (Fluor Protector, FP, Ivoclar Vivadent; Tooth Mousse Plus, TM, GC; 60 Second Gel, A, Germiphene; CavityShield, CS, 3M ESPE) and two fluoride solutions (2% sodium fluoride, N; 8% tin(ii) fluoride, S) were applied on bovine teeth using single and combined methods (10 per group), and then the amount of fluoride release was measured for 4 wk. The electron probe microanalysis and the Vickers microhardness measurements were conducted to assess the effect of fluoride application on the surface properties of bovine teeth. Results The amount of fluoride release was higher in combined applications than in single application (p < 0.05). Microhardness values were higher after combined applications of N with FP, TM, and CS than single application of them, and these values were also higher after combined applications of S than single application of A (p < 0.05). Ca and P values were higher in combined applications of N with TM and CS than single application of them (p < 0.05). They were also increased after combined applications of the S with A than after single application (p < 0.05). Conclusions Combined applications of fluoride could be used as a basis to design more effective methods of fluoride application to provide enhanced remineralization. PMID:27200280

  5. Fluoride stimulates [3H]thymidine incorporation and alkaline phosphatase production by human osteoblasts

    International Nuclear Information System (INIS)

    The effect of sodium fluoride on alkaline phosphatase (ALP) release and [3H]thymidine uptake by human osteoblasts in culture was investigated. Sodium fluoride stimulated both ALP release and [3H]thymidine uptake at concentrations of sodium fluoride greater than 250 mumol/L. This stimulation was similar in magnitude to that induced by 1,25-dihydroxycholecalciferol. The fluoride-induced increase in ALP was inhibited by verapamil, a calcium channel blocker. We conclude that sodium fluoride stimulates osteoblasts to proliferate and to release ALP. This stimulation by fluoride is dependent on calcium influx. Fluoride-induced stimulation of human osteoblasts may be relevant to its effect in enhancing bone formation in patients with osteoporosis

  6. The use of topical fluoride to prevent or reverse dental caries.

    Science.gov (United States)

    Jacobsen, Peter; Young, Douglas

    2003-01-01

    Topical fluoride has been the main stay of caries prevention for many decades. There are several mechanisms which make it beneficial including inhibiting demineralization, enhancing remineralization, and inhibiting bacterial growth. Topical fluoride is available in many different forms. The concentrations of various fluoride preparations range from 225 parts per million (ppm) fluoride in over-the-counter oral rinses to 22,600 ppm in the fluoride varnishes. The clinician must decide which type of topical preparation is best suited for their patient. Patients with high caries risk may benefit from prescription strength fluorides (along with the other chemical and dietary therapies described in this issue of Special Care in Dentistry). The application of fluoride varnish is an excellent topical form for those patients who have access to dental care and for whom it is difficult to comply with the use of other topical forms.

  7. [Ten years of external control over water fluoridation in Chapecó, Santa Catarina State, Brazil].

    Science.gov (United States)

    Panizzi, Mirvaine; Peres, Marco Aurélio

    2008-09-01

    This study aimed to analyze fluoride concentration in the public water supply in Chapecó, Santa Catarina State, Brazil, from 1995 to 2005 and to assess the effectiveness of a fluoridation quality intervention in 2003. A total of 989 water samples were analyzed. Fluoride concentrations were classified according to three different criteria used in Brazil. The city conducted a political and legal intervention in 2003. The Prais-Winsten procedure was used to evaluate the fluoride concentrations over time. In the ten years, the water fluoridation system showed 46%, 32%, and 43% of adequate samples, depending on the criterion. Prior to the municipal intervention, the proportion of adequate samples was 40%, 26%, and 36%, increasing to 63%, 49%, and 61% after the intervention, according to the three criteria. Fluoride concentration improved after the municipal intervention. On-going surveillance is recommended, including water fluoridation, dental caries, and dental fluorosis.

  8. Mathematical model of desublimation process of volatile metal fluorides

    OpenAIRE

    Smolkin, P. А.; Buynovskiy, А. S.; Lazarchuk, V. V.; Matveev, А. А.; Sofronov, V. L.

    2007-01-01

    Mathematical model for calculation of optimal temperature desublimation in metal fluorides and the number of desublimation stages has been developed; it permits achieving the degree of base product recovery from gas-vapour mixture nearly to 100 %. Experimental checking of modeling results at uranium hexafluoride desublimation shows a good correlation with the theoretical data.

  9. Effect of fluoride and chlorhexidine digluconate mouthrinses on plaque biofilms

    DEFF Research Database (Denmark)

    Rabe, Per; Twetman, Svante; Kinnby, Bertil;

    2015-01-01

    in the pre-molar region were worn by three subjects for 7 days. Control discs were removed before subjects rinsed with 0.1% chlorhexidine digluconate (CHX) or 0.2% sodium fluoride (NaF) for 1 minute. Biofilms were stained with Baclight Live/Dead and z-stacks of images created using confocal scanning laser...

  10. Bioethical considerations about water fluoridation: a critical review.

    Directory of Open Access Journals (Sweden)

    María Elisa Quinteros

    2016-08-01

    Full Text Available Dental caries is one of the oral pathologies with greater burden of disease in the Chilean population. Fluoridation of drinking water has been used as a caries prevention strategy. However, its application as a public policy has been questioned since its implementation. The aim of this article is to analyze whether fluoridation of drinking water is a justified measure in reducing the incidence and prevalence of caries from the perspective of bioethics, taking into account the current evidence on its effectiveness. The arguments reviewed are based on the belief that water fluoridation is effective and, in general terms, ethically acceptable. A recent systematic review concludes that there is not enough evidence to support fluoridation as a public policy. There is a gap of knowledge that ought to be closed so that public health authorities can assess the significance of the intervention and make a democratic decision on its continuation or suspension based on scientific evidence. This decision should be informed and disseminated within the community.

  11. Reversible Intercalation of Fluoride-Anion Receptor Complexes in Graphite

    Science.gov (United States)

    West, William C.; Whitacre, Jay F.; Leifer, Nicole; Greenbaum, Steve; Smart, Marshall; Bugga, Ratnakumar; Blanco, Mario; Narayanan, S. R.

    2007-01-01

    We have demonstrated a route to reversibly intercalate fluoride-anion receptor complexes in graphite via a nonaqueous electrochemical process. This approach may find application for a rechargeable lithium-fluoride dual-ion intercalating battery with high specific energy. The cell chemistry presented here uses graphite cathodes with LiF dissolved in a nonaqueous solvent through the aid of anion receptors. Cells have been demonstrated with reversible cathode specific capacity of approximately 80 mAh/g at discharge plateaus of upward of 4.8 V, with graphite staging of the intercalant observed via in situ synchrotron X-ray diffraction during charging. Electrochemical impedance spectroscopy and B-11 nuclear magnetic resonance studies suggest that cointercalation of the anion receptor with the fluoride occurs during charging, which likely limits the cathode specific capacity. The anion receptor type dictates the extent of graphite fluorination, and must be further optimized to realize high theoretical fluorination levels. To find these optimal anion receptors, we have designed an ab initio calculations-based scheme aimed at identifying receptors with favorable fluoride binding and release properties.

  12. Een ionchromatografische methode voor de bepaling van fluoride in water

    NARCIS (Netherlands)

    Beld WA van den; Cleven RFMJ; Neele J; LAC

    1998-01-01

    Dit rapport bevat resultaten van het onderzoek naar het ontwikkelen van een geautomatiseerde ionchromatografische methode voor de bepaling van fluoride, acetaat en formiaat in diverse waterige milieu's. Het onderzoek heeft geresulteerd in een betrouwbare, selectieve en gevoelige methode vo

  13. Fluoride volatility technology for reprocessing of irradiated oxide fuel

    International Nuclear Information System (INIS)

    A review of the scientific research works in the VNIIKhT on the spent oxide fuel reprocessing by the fluoride volatility technology is presented. Refining feasibilities of the basic stages of the fluoride volatility technology were investigated. Possibility of the release of the basic part of fission products with cinders on the fluorination stage was supported by the experimental results. Application of the fluorine sorbents (NaF, BaF2) means for the summary coefficient of the UF6 purification from fission products at a level of 107. Possibility of the deep plutonium recovery from the oxide fuel was shown. Results of the investigations into pyrohydrolysis of UF6 and mixture of UF6 and PuF6 with the oxide granulates production of the needed density with the content of fluorine 0.005 mass. % and oxygen coefficient 2 - 2.1 are performed. Recommendations on the fluoride volatility process application for the spent oxide fuel reprocessing of fast and light water reactors and prediction on the closed fuel cycle using fluoride volatility process were given with regard to new demands on fission products nonproliferation

  14. Hydrogen Fluoride in High-mass Star-forming Regions

    NARCIS (Netherlands)

    Emprechtinger, M.; Monje, R. R.; van der Tak, F. F. S.; van der Wiel, M. H. D.; Lis, D. C.; Neufeld, D.; Phillips, T. G.; Ceccarelli, C.

    2012-01-01

    Hydrogen fluoride (HF) has been established to be an excellent tracer of molecular hydrogen in diffuse clouds. In denser environments, however, the HF abundance has been shown to be approximately two orders of magnitude lower. We present Herschel/HIFI observations of HF J = 1-0 toward two high-mass

  15. ADEQUACY OF SAMPLING TRAINS AND ANALYTICAL PROCEDURES USED FOR FLUORIDE

    Science.gov (United States)

    Liquid nitrogen-cooled cold-traps were used to establish the collection efficiency for fluorides of two different source sampling trains at primary aluminum reduction plants and wet-process phosphoric acid plants. It was found that the glass frit filter support commonly used in s...

  16. Transference system of gaseous fluoride compounds for infrared spectrofotometric analysis

    International Nuclear Information System (INIS)

    A vacuum line design for transference of gaseous fluoride compounds involved in the uranium hexafluoride infrared analysis is presented. The text include specific comments about the characteristics of each component and about the possibilities of its acquisition in the national market. (author)

  17. Measuring Bone Metabolism with Fluoride PET: Methodological Considerations.

    Science.gov (United States)

    Apostolova, Ivayla; Brenner, Winfried

    2010-07-01

    In recent years the more widespread availability of PET systems and the development of hybrid PET/computed tomography (CT) imaging, allowing improved morphologic characterization of sites with increased tracer uptake, have improved the accuracy of diagnosis and strengthened the role of 18F-fluoride PET for quantitative assessment of bone pathology. This article reviews the role of 18F-fluoride PET in the skeleton, with a focus on (1) the underlying physiologic and pathophysiological processes of different conditions of bone metabolism and (2) methodological aspects of quantitative measurement of 18F-fluoride kinetics. Recent comparative studies have demonstrated that 18F-fluoride PET and, to an even greater extent, PET/CT are more accurate than 99mTc-bisphosphonate single-photon emission CT for the identification of malignant and benign lesions of the skeleton. Quantitative 18F-flouride PET has been shown valuable for direct non-invasive assessment of bone metabolism and monitoring response to therapy.

  18. Slow-release fluoride devices: a literature review

    Directory of Open Access Journals (Sweden)

    Juliano Pelim Pessan

    2008-08-01

    Full Text Available Although the prevalence of caries has decreased dramatically over the past decades, it has become a polarised disease, with most of subjects presenting low caries levels and few individuals accounting for most of the caries affected surfaces. Thus it become evident for the need of clinical approaches directed at these high-risk patients, in order to overcome problems related to compliance and low attendance at dental care centres. Slow-release fluoride devices were developed based on the inverse relationship existing between intra-oral fluoride levels and dental caries experience. The two main types of slow-release devices - copolymer membrane type and glass bead - are addressed in the present review. A substantial number of studies have demonstrated that these devices are effective in raising intra-oral F concentrations at levels able to reduce enamel solubility, resulting in a caries-protective effect. Studies in animals and humans demonstrated that the use of these devices was able to also protect the occlusal surfaces, not normally protected by conventional fluoride regimens. However, retention rates have been shown to be the main problem related to these devices and still requires further improvements. Although the results of these studies are very promising, further randomised clinical trials are needed in order to validate the use of these devices in clinical practice. The concept of continuously providing low levels of intra-oral fluoride has great potential for caries prevention in high caries-risk groups.

  19. Fluoride Varnish for Caries Prevention: Efficacy and Implementation.

    Science.gov (United States)

    Bonetti, Debbie; Clarkson, Jan E

    2016-01-01

    Many reviews support fluoride varnish (FV) as a caries-inhibitory agent. Evidence from 6 Cochrane systematic reviews involving 200 trials and more than 80,000 participants further confirms the effectiveness of FV, applied professionally 2-4 times a year, for preventing dental caries in both primary and permanent teeth. The relative benefit of FV application seems to occur irrespective of baseline caries risk, baseline caries severity, background exposure to fluorides, use of fluoride toothpaste and application features such as prior prophylaxis, concentration of fluoride or frequency of application. While the efficacy of FV is acknowledged in clinical practice guidelines globally, the implementation of this recommendation may still be an issue. Factors that may facilitate FV application in the USA include Medicaid eligibility, relationships with dentists/community centers and strong cooperation and communication between physicians and support staff. Barriers include insufficient time to integrate oral health services into well-child visits, difficulty in applying FV (lack of skills/training) and resistance among colleagues and staff. Research in the UK/Scotland also suggests encouraging clinicians in their motivation to perform this treatment and addressing professional and parental concerns relating to possible negative consequences may be influential. Further research targeting cost-effectiveness and how FV in routine care may fit in with political agendas relating to, for example, inequalities in health care provision and access will also play a key part in stakeholder decisions to put resources into this issue. PMID:27100219

  20. Effects of sodium fluoride on immune response in murine macrophages.

    Science.gov (United States)

    De la Fuente, Beatriz; Vázquez, Marta; Rocha, René Antonio; Devesa, Vicenta; Vélez, Dinoraz

    2016-08-01

    Excessive fluoride intake may be harmful for health, producing dental and skeletal fluorosis, and effects upon neurobehavioral development. Studies in animals have revealed effects upon the gastrointestinal, renal and reproductive systems. Some of the disorders may be a consequence of immune system alterations. In this study, an in vitro evaluation is made of fluoride immunotoxicity using the RAW 264.7 murine macrophage line over a broad range of concentrations (2.5-75mg/L). The results show that the highest fluoride concentrations used (50-75mg/L) reduce the macrophage population in part as a consequence of the generation of reactive oxygen and/or nitrogen species and consequent redox imbalance, which in turn is accompanied by lipid peroxidation. A decrease in the expression of the antiinflammatory cytokine Il10 is observed from the lowest concentrations (5mg/L). High concentrations (50mg/L) in turn produce a significant increase in the proinflammatory cytokines Il6 and Mip2 from 4h of exposure. In addition, cell phagocytic capacity is seen to decrease at concentrations of ≥20mg/L. These data indicate that fluoride, at high concentrations, may affect macrophages and thus immune system function - particularly with regard to the inflammation autoregulatory processes, in which macrophages play a key role. PMID:26965474

  1. Efficacy of xylitol and fluoride mouthrinses on salivary mutans streptococci

    Science.gov (United States)

    Arunakul, Malee; Thaweboon, Boonyanit; Thaweboon, Sroisiri; Asvanund, Yuwadee; Charoenchaikorn, Kesinee

    2011-01-01

    Objective To evaluate the level of salivary Mutans streptococci (MS) after rinsing with xylitol, fluoride, and a combination of xylitol and fluoride solutions, compared with distilled water. Methods Eighty healthy 8-9 years old subjects with high level of MS (> 105 CFU/mL) were equally divided into 4 groups. Subjects rinsed their mouths for 1 min with 10 mL of 0.05% (w/v) sodium fluoride (NaF), 12.5% (w/v) xylitol or 0.05% (w/v) NaF + 12.5% (w/v) xylitol 3 times daily over 10 weeks. Distilled water rinsed group served as a control. Paraffin-stimulated whole saliva samples were collected at baseline, 5 weeks, and 10 weeks after rinsing to determine the level of salivary MS by culturing on Mitis Salivarius Bacitracin agar. The statistical significance was calculated by Kruskal Wallis, Mann Whitney U, and Wilcoxon signed-rank tests at a significant level of P< 0.05. Results Significant reductions in MS count were observed in subjects using 0.05% NaF + 12.5% xylitol over other groups within 5 weeks and after 10 weeks and 12.5% xylitol alone after 10 weeks compared with baseline. Conclusions The present study provides evidence for the inhibitory effect of xylitol, used in combination with fluoride, delivered in the form of mouthrinse, on salivary MS in the group of schoolchildren. PMID:23569819

  2. Efficacy of xylitol and fluoride mouthrinses on salivary mutans streptococci

    Institute of Scientific and Technical Information of China (English)

    Sroisiri Thaweboon; Yuwadee Asvanund; Kesinee Charoenchaikorn

    2011-01-01

    To evaluate the level of salivary Mutans streptococci (MS) after rinsing with xylitol, fluoride, and a combination of xylitol and fluoride solutions, compared with distilled water. Methods: Eighty healthy 8-9 years old subjects with high level of MS (> 105 CFU/mL) were equally divided into 4 groups. Subjects rinsed their mouths for 1 min with 10 mL of 0.05% (w/v) sodium fluoride (NaF), 12.5% (w/v) xylitol or 0.05% (w/v) NaF + 12.5% (w/v) xylitol 3 times daily over 10 weeks. Distilled water rinsed group served as a control. Paraffin-stimulated whole saliva samples were collected at baseline, 5 weeks, and 10 weeks after rinsing to determine the level of salivary MS by culturing on Mitis Salivarius Bacitracin agar. The statistical significance was calculated by Kruskal Wallis, Mann Whitney U, and Wilcoxon signed-rank tests at a significant level ofP< 0.05. Results: Significant reductions in MS count were observed in subjects using 0.05% NaF+ 12.5% xylitol over other groups within 5 weeks and after 10 weeks and 12.5% xylitol alone after 10 weeks compared with baseline. Conclusions: The present study provides evidence for the inhibitory effect of xylitol, used in combination with fluoride, delivered in the form of mouthrinse, on salivary MS in the group of schoolchildren.

  3. THE USE OF FLUORIDE CONTAINING MINERAL WATER IN WORT PRODUCTION

    Directory of Open Access Journals (Sweden)

    Gunka Yonkova

    2011-12-01

    Full Text Available The present work aims to study the quality of wort produced using fluoride containing mineral water. The results show that the mineral water has a negative impact on the enzymatic destruction of starch, proteins, color intensity and pH of the wort. The changes of pH during mashing process using tap and mineral water was studied. The lower acidity of wort obtained using mineral water didn’t change during the brewing process. The fluoride content of beer is lower than 5 mg.L-1 when wort is produced using mineral and tap water in 1:1 ratio and citric acid for pH correction. At the same time, the final degree of fermentation, α-amine nitrogen content and the intensity of color of produced wort are close to the control sample. The changes in fluoride ion concentration are monitored using ion-selective potentiometry. The fluoride content is decreased from 5.7 to 4.75 mg.L-1, the most intense change is observed during the mashing process.

  4. CAN FLUORIDATION AFFECT WATER LEAD LEVELS AND LEAD NEUROTOXICITY?

    Science.gov (United States)

    Recent reports have attempted to show that certain approaches to fluoridating potable water is linked to increased levels of lead(II) in the blood. We examine these claims in light of the established science and critically evaluate their significance. The completeness of nexafluo...

  5. Effects of amine fluoride on biofilm growth and salivary pellicles

    NARCIS (Netherlands)

    Van der Mei, HC; Engels, E; de Vries, Jacob; Busscher, HJ

    2008-01-01

    The amine fluoride (AmF) N'-octadecyltrimethylendiamine-N, N,N'-tris(2-ethanol)-dihydrofluoride is a cationic antimicrobial which can have beneficial effects on plaque formation. Here, we determine changes in pellicle and bacterial cell surface properties of the strains Actinomyces naeslundii HM1, S

  6. Electrodeposition of transuranic elements in molten fluoride media

    Energy Technology Data Exchange (ETDEWEB)

    Huguet, Anne; Bourg, Stephane; Lacquement, Jerome [CEA Marcoule, DEN/DRCP/SCPS/LPP, Bat. 399, B.P. 17171, 30207 Bagnols-sur-Ceze (France); Ghetta, Veronique [IN2P3/LPSC, UMR 5821, 38026 Grenoble Cedex 1 (France); Fouletier, Jacques [ENSEEG/LEPMI, UMR 5631, B.P. 75, 38402 Saint Martin d' Heres (France)

    2008-07-01

    The aim of this work is to evaluate the performance of an electrolytic pyrochemical process for the An-Ln separation in molten fluoride media. The attempts of electrodeposition would be performed onto liquid bismuth. Additionally, this work represents an advance in the electrolytic methods as far as the electrolysis would be carried out onto a dropping bismuth electrode. (authors)

  7. Sensitivity of two biomarkers for biomonitoring exposure to fluoride in children and women: A study in a volcanic area.

    Science.gov (United States)

    Linhares, Diana Paula Silva; Garcia, Patrícia Ventura; Amaral, Leslie; Ferreira, Teresa; Cury, Jaime A; Vieira, Waldomiro; Rodrigues, Armindo Dos Santos

    2016-07-01

    The natural enrichment of water with fluoride is related to natural sources such as volcanic activity, with it being documented that fluorosis, an endemic and widespread disease in volcanic areas, is associated to the ingestion of high levels of fluoride through water. Thus, in this study, we aimed to define the fluoride concentration in drinking waters of volcanic origin and compare the sensitivity of urine and nail clippings as biomarkers for fluoride exposure in adults and children. Samples of drinking water from four villages in São Miguel Island (Azores) were used and the fluoride concentration was determined, as well the fluoride content in urine and toenails clippings from 66 children and 63 adults from these villages. A validated diet questionnaire, assessing sources of fluoride, was recorded for each participant. The fluoride determination in urine and nail clipping samples was made using a fluoride-specific electrode. A positive correlation was found between the fluoride daily intake and fluoride content in children urine (rs = 0.475; p intake correlated positively with fluoride content nail clippings (rs = 0.495, p children vs. adults). Furthermore, nail clippings are more suitable than urine fluoride levels to assess long term exposure to fluoride in areas where the exposure to fluoride in drinking water is considered within, or slightly above, the recommended legal values. PMID:27155929

  8. Effect of fluoride-free and fluoridated carbamide peroxide gels on the hardness and surface roughness of aesthetic restorative materials

    Directory of Open Access Journals (Sweden)

    Homayoon Alaghehmand

    2013-01-01

    Full Text Available Background: Bleaching products may show some side effects on soft and hard tissues and restorative materials in the oral cavity. This study evaluated the effect of carbamide peroxide gel with and without fluoride ions on the microhardness and surface roughness of tooth-colored restorative materials. Materials and Methods: In this in-vitro study, 76 cubic specimens (4 mm 3 × 4 mm 3 × 3 mm 3 were fabricated from 4 aesthetic A3-shade restorative materials. These materials consisted of two composite resins and two glass ionomers. The specimens made from each material were treated with the following surface treatments: 1. Control group: The specimens were not bleached and were stored in normal saline. Group 2. Fluoridated 20% carbamide peroxide gel, treated 3 h a day for 4 weeks. Group 3. Treated 1 h a day with fluoride-less 22% carbamide peroxide for two weeks. From each group, three other specimens were selected to be evaluated in terms of changes in surface roughness, under scanning electron microscopy (SEM. Results: In this study, fluoridated 20% carbamide peroxide gel increased the microhardness of the four aesthetic restorative materials. The fluoride-free carbamide peroxide 22% reduced the microhardness of the four used materials, which this change was significant for Vitremer and Amelogen. SEM analyses showed changes in surface roughness of glass ionomer specimens. Conclusion: The effect of bleaching on the microhardness of restorative materials is material dependent. Before the application of bleaching systems on the glass ionomer materials, the application of a protective barrier should be considered.

  9. Effect of different frequencies of fluoride dentifrice and mouthrinse administration: an in situ study

    Directory of Open Access Journals (Sweden)

    Daniela Correia Cavalcante Souza

    2010-12-01

    Full Text Available The effect of a combination of topical fluoridation methods for inhibition of enamel demineralization in the face of a cariogenic challenge has not been clearly established. This in situ crossover study aimed to assess whether the addition of daily use of fluoride mouthrinse (FR to that of fluoride dentifrice (FD is equivalent to increasing the frequency of FD application in terms of the effect on enamel demineralization and fluoride content. Over 3 phases of 14 days each, 12 volunteers wore appliances containing enamel blocks exposed to a 20 % sucrose solution 8 times/day. During each phase the blocks underwent one of the following treatments: 2x/day FD, 2x/day FD + 1x/day FR, and 3x/day FD. The blocks were assessed for hardness and fluoride content. Three x/day FD did not differ from 2x/day + 1x/day FR, however it enhanced demineralization protection when compared to 2x/day FD. All treatments produced an increase in enamel fluoride content compared to no treatment (sound blocks (p < 0.05, but the differences between them were not significant. The results of this study suggest that the daily use of fluoride mouthrinse combined with that of fluoride dentifrice has similar effects on enamel demineralization and fluoride content when compared to increasing the frequency of fluoride dentifrice use.

  10. Protective effect of ascorbic acid and Ginkgo biloba against learning and memory deficits caused by fluoride.

    Science.gov (United States)

    Jetti, Raghu; Raghuveer, C V; Mallikarjuna, Rao C

    2016-01-01

    Fluoride is present in the ground water, World Health Organization permitted level of fluoride in the ground water is 0.5 ppm. Tooth pastes, mouth washes, tea and sea fish are the sources of fluoride. Exposure to these multiple sources results in several adverse effects in addition to the fluorosis. The present study aimed to test the effect of vitamin C and Ginkgo biloba against the behavioural deficits caused by fluoride. Rats were divided into five groups with six animals in each group (n = 6). Control group received ordinary tap water with 0.5 ppm of fluoride, the remaining groups received 100 ppm of fluoride for 30 days prior to fluoride exposure. Two groups of animals received 100 mg/kg body weight of vitamin C and G. biloba for 15 days prior to fluoride exposure. After 45 days, behavioural studies (T-Maze, passive avoidance) were conducted on the experimental animals. The results of the present study showed no behavioural deficits in the control group of animals however, the rats that received fluoride water exhibited impairment in their spatial learning and memory deficits. The deficits are not marked in the vitamin C and G. biloba groups. To conclude chronic exposure to high levels of fluoride causes severe impairment in the spatial learning and memory, these deficits can be ameliorated with the vitamin C and G. biloba.

  11. Fluoride bioaccumulation by hydroponic cultures of camellia (Camellia japonica spp.) and sugar cane (Saccharum officinarum spp.).

    Science.gov (United States)

    Camarena-Rangel, Nancy; Rojas Velázquez, Angel Natanael; Santos-Díaz, María del Socorro

    2015-10-01

    The ability of hydroponic cultures of camellia and sugar cane adult plants to remove fluoride was investigated. Plants were grown in a 50% Steiner nutrient solution. After an adaptation period to hydroponic conditions, plants were exposed to different fluoride concentrations (0, 2.5, 5 and 10 mg L(-1)). Fluoride concentration in the culture medium and in tissues was measured. In sugar cane, fluoride was mainly located in roots, with 86% of it absorbed and 14% adsorbed. Sugar cane plants removed 1000-1200 mg fluoride kg(-1) dry weight. In camellia plants the highest fluoride concentration was found in leaf. Roots accumulated fluoride mainly through absorption, which was 2-5 times higher than adsorption. At the end of the experiment, fluoride accumulation in camellia plants was 1000-1400 mgk g(-1) dry weight. Estimated concentration factors revealed that fluoride bioaccumulation is 74-221-fold in camellia plants and 100-500-fold in sugar cane plants. Thus, the latter appear as a suitable candidate for removing fluoride from water due to their bioaccumulation capacity and vigorous growth rate; therefore, sugar cane might be used for phytoremediation. PMID:25930125

  12. Fluoride in the drinking water of Pakistan and the possible risk of crippling fluorosis

    Directory of Open Access Journals (Sweden)

    M. A. Tahir

    2013-02-01

    Full Text Available To explore the possibility of fluoride toxicity, 747 water samples were collected from surface water and groundwater sources of 16 major cities of Pakistan, adopting a uniform sampling design with distribution of samples: Lahore (79, Kasur (46, Faisalabad (30, Khushab (50, Chakwal (51, Mianwali (30, Jhelum (53, Bahawalpur (60, Karachi (60, Mirpur Khas (55, Peshawar (38, Risalpur (35, Quetta (81, Ziarat (21, Loralai (21, and Mastung (37. Comparison of analytical findings with WHO Guidelines of Drinking Water for Fluoride (i.e., 1.5 ppm has concluded that 16% of the monitored water sources have fluoride concentration beyond the permissible safe limit of 1.5 mg L−1 falling in the concentration range of 1.6–25 mg L−1. The highest fluoride contamination (22% is detected in the Balochistan province followed by 19% in Punjab province. Comparatively higher fluoride levels of > 20% in the groundwater sources like hand pumps supported the possibility of increased groundwater contamination as excessive fluoride concentrations are expected to come from calcium-poor aquifers and in areas where fluoride-bearing minerals are common or where cation exchange of sodium for calcium occurs. Field observations have also indicated the prevalence of fluoride-associated health implications in the study areas with excessive fluoride in water sources. Findings of this study have provided bidirectional vision for the epidemiological investigations as well as to mitigate the issues in the affected vicinities of fluoride-rich areas.

  13. Fluoride bioaccumulation by hydroponic cultures of camellia (Camellia japonica spp.) and sugar cane (Saccharum officinarum spp.).

    Science.gov (United States)

    Camarena-Rangel, Nancy; Rojas Velázquez, Angel Natanael; Santos-Díaz, María del Socorro

    2015-10-01

    The ability of hydroponic cultures of camellia and sugar cane adult plants to remove fluoride was investigated. Plants were grown in a 50% Steiner nutrient solution. After an adaptation period to hydroponic conditions, plants were exposed to different fluoride concentrations (0, 2.5, 5 and 10 mg L(-1)). Fluoride concentration in the culture medium and in tissues was measured. In sugar cane, fluoride was mainly located in roots, with 86% of it absorbed and 14% adsorbed. Sugar cane plants removed 1000-1200 mg fluoride kg(-1) dry weight. In camellia plants the highest fluoride concentration was found in leaf. Roots accumulated fluoride mainly through absorption, which was 2-5 times higher than adsorption. At the end of the experiment, fluoride accumulation in camellia plants was 1000-1400 mgk g(-1) dry weight. Estimated concentration factors revealed that fluoride bioaccumulation is 74-221-fold in camellia plants and 100-500-fold in sugar cane plants. Thus, the latter appear as a suitable candidate for removing fluoride from water due to their bioaccumulation capacity and vigorous growth rate; therefore, sugar cane might be used for phytoremediation.

  14. Effect of high fluoride concentration in drinking water on children’s intelligence

    Directory of Open Access Journals (Sweden)

    Seraj B

    2006-07-01

    Full Text Available Background and Aim: Human and animal studies linking fluoride with diminished intelligence have been published. Although adverse effects of high intake of fluoride on intelligence and mental acuity continue to be reported, they are still controversial. The aim of this research was to investigate the relationship between fluoride in drinking water and children's intelligence. Materials and Methods: In this cross sectional study, 41 children were selected from the high fluoride area with 2.5mg/l (ppm fluoride in the drinking water and 85 children were selected from low fluoride area with 0.4mg/l (ppm fluoride in the drinking water. The intelligence quotient (IQ of each child was measured by the Raven's test. The history of illnesses affecting the nervous system, head trauma, birth weight (2.5kg or  2.5kg, residental history, age and sex of children were investigated by questionnaires completed by the children's parents. Data were analyzed by Chi-Square test with p<0.05 as the limit of significance. Results: In the high fluoride area the mean IQ of children (87.911 was significantly lower than in the low fluoride area (98.912.9 (P=0.025. Conclusion: Based on the findings of this study, exposure of children to high levels of fluoride may carry the risk of impaired development of intelligence.

  15. Effect of High Water Fluoride Concentration on the Intellectual Development of Children in Makoo/Iran

    Directory of Open Access Journals (Sweden)

    M Shadfar

    2012-01-01

    Full Text Available Objective: Prolonged excessive intake of fluoride during child’s growth and development stages has been associated with mental and physical problems.The aim of this study was to investigate the effect of excessive fluoride intake on the intelligence quotient (IQ of children living in five rural areas in Makoo/Iran.Materials and Methods: In this cross-sectional study, 293 children aged 6-11 years were selected from five villages in Makoo with normal fluoride (0.8±0.3 ppm, medium fluoride (3.1±0.9 ppm and high fluoride (5.2±1.1 ppm in their water supplies. The IQ of each child was measured by the Raven’s test. Educational and residential information and the medical history of each child was recorded by a questionnaire completed by the parents. Data were analyzed by ANOVA test with a significance level of 0.05.Results: The mean IQ scores decreased from 97.77±18.91 for the normal fluoride group to 89.03±12.99 for the medium fluoride group and to 88.58±16.01 for the high fluoride group (P=0.001.Conclusion: Children residing in areas with higher than normal water fluoride levels demonstrated more impaired development of intelligence. Thus, children’s intelligence may be affected by high water fluoride levels.

  16. Enhancing Fluoride: Clinical Human Studies of Alternatives or Boosters for Caries Management.

    Science.gov (United States)

    Fontana, Margherita

    2016-01-01

    Dental caries remains a major public health problem, especially for certain high-risk population groups. The goal of this study was to assess the evidence regarding strategies meant to be used as alternatives or booster/supplements to fluoride for caries prevention and management. Articles were selected for inclusion if they had a prospective longitudinal design, with a fluoride control arm, and were conducted in human subjects. Of the included studies, 7/18 studies on calcium-based strategies favored the test product (the majority of studies included exposure of fluoride in all groups). All the arginine studies (8/8) included a combination of arginine and a calcium base, and concluded that this has the potential to significantly boost the performance of fluoride. The remaining included studies focused on the addition of microbial-related strategies to a fluoride-containing vehicle (2 xylitol studies and 1 study using a probiotic milk), and all favored the combination as a booster to fluoride. Thus, the current study did not identify evidence for any strategy to effectively be used as a substitute or alternative to fluoride, but identified some consistent evidence derived from the use of prebiotic strategies (primarily from use of arginine combined with calcium) to support their potential use to boost the mechanism of action of fluoride. Thus, fluoride-based strategies remain the standard for caries prevention and management, with some evidence that boosting the effects of fluoride by the use of prebiotic strategies is a promising possibility. PMID:27100833

  17. The interaction of polyacid-modified composite resins ("compomers" with aqueous fluoride solutions

    Directory of Open Access Journals (Sweden)

    Reza Rohani

    2009-06-01

    Full Text Available OBJECTIVE : The aim of this study was to investigate how the release of fluoride from two compomers and a fluoridated composite resin was affected by exposure to KF solution. MATERIAL AND METHODS: Two compomers (Dyract AP and Compoglass F and one fluoridated composite (Wave were prepared as discs (6 mm diameter and 2 mm thick, curing with a standard dental lamp. They were then stored in either water or 0.5% KF for 1 week, followed by placement in water for periods of 1 week up to 5 weeks total. Fluoride was determined with and without TISAB (to allow complexed and decomplexed fluoride to be determined, and other ion release (Na, Ca, Al, Si, P was determined by ICP-OES. RESULTS: Specimens were found not to take up fluoride from 100 ppm KF solution in 24 h, but to release additional fluoride when stored for up to five weeks. Compomers released more fluoride cumulatively following exposure to KF solution (p<0.001, all of which was decomplexed, though initial (1 week values were not statistically significant for Dyract AP. Other ions showed no variations in release over 1 week, regardless of whether the specimens were exposed to KF. Unlike the compomers, Wave showed no change in fluoride release as a result of exposure to KF. CONCLUSIONS: Compomers are affected by KF solution, and release more fluoride (but not other ions after exposure than if stored in water.

  18. In vitro evaluation of fluoride products in the development of carious lesions in deciduous teeth

    Directory of Open Access Journals (Sweden)

    Lucineide de Melo Santos

    2009-09-01

    Full Text Available The purpose of this study was to evaluate the effect of the application of fluoride products on the development of enamel caries in deciduous teeth. A total of 108 deciduous teeth were chosen for the study. Acid-resistant varnish was applied on the teeth, leaving only one area of 5 mm x 1 mm of dental enamel exposed. The teeth were allocated randomly to one of the following groups: 1 control - toothpaste without fluoride; 2 1.23% fluoride gel; 3 Duraflur fluoride varnish; 4 Duraphat fluoride varnish; 5 Fluorniz fluoride varnish; 6 Fluorphat fluoride varnish; 7 varnish with Duofluorid; 8 12% silver fluoride diamine (Cariestop; 9 children's fluoride toothpaste (500 ppm. The tested products were applied on the teeth according to the manufacturer's recommendations and the teeth were stored in a moist environment for 24 hours. Each group of teeth was then subjected to a pH cycling model for 14 days, after which the teeth were cut through the center for an analysis of the depth of the carious lesion by polarized light microscopy. Comparisons were made between the treatments and the control group. The mean lesion depth values were 318 μm ± 39 (control, 213 μm ± 27 (fluoride gel, 203 μm ± 34 (Duraflur, 133 μm ± 25 (Duraphat, 207 μm ± 27 (Fluor-niz, 212 μm ± 27 (Fluorphat, 210 ± 28 (Duofluorid, 146 ± 31 (Cariestop and 228 ± 24 (fluoride toothpaste. None of the products used here was able to completely prevent the formation of lesions. The highest cariostatic effect was achieved by fluoride varnish Duraphat and the lowest by the fluoride toothpaste.

  19. Acceptability of Salt Fluoridation in a Rural Latino Community in the United States: An Ethnographic Study.

    Directory of Open Access Journals (Sweden)

    Judith C Barker

    Full Text Available Compared to other population groups in the United States, caries (tooth decay is a disproportionately prevalent disease among Latino populations, especially among low-income and rural sub-groups and children under five years of age. Fluoride is a primary preventive for caries. While water fluoridation is a major and effective public health means for delivering fluoride on a mass scale, it does not reach many rural areas or population groups such as Latinos who eschew drinking water from municipal sources. This study examines the acceptability to such groups of salt fluoridation, an alternate means of delivering fluoride long used on a global scale. An ethnographic study in California's rural Central Valley was performed. Thirty individual interviews and 5 focus groups (N = 61 were conducted in Spanish to investigate low-income Latino migrant caregivers' experiences, views and understandings of domestic salt, oral health, caries prevention and fluoride. Audio data were transcribed, translated, coded and thematically analyzed. Table salt was readily available and frequently consumed. Both adult and child daily sodium consumption was high. Despite a general feeling that it was good, and present in dentifrices or dietary supplements, most participants had little knowledge about fluoride. Concerns were raised about cardio-vascular and other possibly deleterious effects if an increase in salt consumption occurred because fluoridated salt was viewed as having 'extra' benefits. Once informed about fluoride's safety and role in caries prevention, most participants expressed willingness to use fluoridated salt, especially if it benefitted children. Reassurance about its safety and benefits, and demonstration of its taste, were important aspects of acceptance. Taste was paramount. Participants would not consume more fluoridated salt than their current salt as that would result in unpleasant changes in food flavor and taste. While salt fluoridation is

  20. Critical factors determining fluoride concentration in tea leaves produced from Anhui province, China.

    Science.gov (United States)

    Cai, Huimei; Zhu, Xiaohui; Peng, Chuanyi; Xu, Wei; Li, Daxiang; Wang, Yijun; Fang, Shihui; Li, Yeyun; Hu, Shaode; Wan, Xiaochun

    2016-09-01

    This study investigated the fluoride present in tea plants (Camellia sinensis (L.) O. Kuntze) and its relationship to soils, varieties, seasons and tea leaf maturity. The study also explored how different manufacturing processes affect the leaching of fluoride into tea beverages. The fluoride concentration in the tea leaves was significantly correlate to the concentration of water-soluble fluoride in the soil. Different tea varieties accumulated different levels of fluoride, with varieties, Anji baicha having the highest and Nongkang zao having the lowest fluoride concentration. In eight different varieties of tea plant harvested over three tea seasons, fluoride concentration were highest in the summer and lowest in the spring in china. The fluoride concentration in tea leaves was directly related to the maturity of the tea leaves at harvest. Importantly, the tea manufacturing process did not introduced fluoride contamination. The leaching of fluoride was 6.8% and 14.1% higher in black and white tea, respectively, than in fresh tea leaves. The manufacturing step most affecting the leaching of fluoride into tea beverage was withering used in white, black and oolong tea rather than rolling or fermentation. The exposure and associated health risks for fluoride concentration in infusions of 115 commercially available teas from Chinese tea markets was determined. The fluoride concentration ranged from 5.0 to 306.0mgkg(-1), with an average of 81.7mgkg(-1). The hazard quotient (HQ) of these teas indicated that there was no risk of fluorosis from drinking tea, based on statistical analysis by Monte Carlo simulation. PMID:27162130

  1. Acceptability of Salt Fluoridation in a Rural Latino Community in the United States: An Ethnographic Study.

    Science.gov (United States)

    Barker, Judith C; Guerra, Claudia; Gonzalez-Vargas, M Judy; Hoeft, Kristin S

    2016-01-01

    Compared to other population groups in the United States, caries (tooth decay) is a disproportionately prevalent disease among Latino populations, especially among low-income and rural sub-groups and children under five years of age. Fluoride is a primary preventive for caries. While water fluoridation is a major and effective public health means for delivering fluoride on a mass scale, it does not reach many rural areas or population groups such as Latinos who eschew drinking water from municipal sources. This study examines the acceptability to such groups of salt fluoridation, an alternate means of delivering fluoride long used on a global scale. An ethnographic study in California's rural Central Valley was performed. Thirty individual interviews and 5 focus groups (N = 61) were conducted in Spanish to investigate low-income Latino migrant caregivers' experiences, views and understandings of domestic salt, oral health, caries prevention and fluoride. Audio data were transcribed, translated, coded and thematically analyzed. Table salt was readily available and frequently consumed. Both adult and child daily sodium consumption was high. Despite a general feeling that it was good, and present in dentifrices or dietary supplements, most participants had little knowledge about fluoride. Concerns were raised about cardio-vascular and other possibly deleterious effects if an increase in salt consumption occurred because fluoridated salt was viewed as having 'extra' benefits. Once informed about fluoride's safety and role in caries prevention, most participants expressed willingness to use fluoridated salt, especially if it benefitted children. Reassurance about its safety and benefits, and demonstration of its taste, were important aspects of acceptance. Taste was paramount. Participants would not consume more fluoridated salt than their current salt as that would result in unpleasant changes in food flavor and taste. While salt fluoridation is acceptable, the

  2. 高氟土壤的氟动力学吸附试验研究%Experiment on Fluoride Kinetics Adsorption of High Fluoride Soils

    Institute of Scientific and Technical Information of China (English)

    段江飞; 刘浩; 时孟杰

    2014-01-01

    通过室内水土试验,研究山东高密高氟地区的土壤对氟的动力学吸附特性,并用典型的低氟土试验进行对比。从化学动力学的角度讨论高氟土壤对氟的吸附行为。高氟土壤对氟的吸附有其特殊性;高氟土壤对氟的吸附分为快、慢两个阶段;羟基是影响氟吸附的重要因素。%Through indoor soil test,the article is based on strudies fluorine kinetics adsorption of soils in high density flu-oride region of Shandong Province and comparing by low fluoride soil experiment.It discusses the way of Fluoride adsorp-tion by high fluoride soils from the point of chemical kinetics.The results show that fluoride adsorption by high fluoride soils has its particularity;the tendency of fluoride adsorption is faster at the first stage and slower at the second stage;Hydroxyl is one of the important factors to affect the fluoride adsorption.

  3. Effect of various rinsing protocols after use of amine fluoride/stannous fluoride toothpaste on the bacterial composition of dental plaque

    NARCIS (Netherlands)

    C. van Loveren; V.A.M. Gerardu; C.H. Sissons; M. van Bekkum; J.M. ten Cate

    2009-01-01

    This clinical study evaluated the effect of different oral hygiene protocols on the bacterial composition of dental plaque. After a 2-week period of using fluoride-free toothpaste, 30 participants followed three 1-week experimental protocols, each followed by 2-week fluoride-free washout periods in

  4. Pronounced reduction of fluoride exposure in free-ranging deer in North Bohemia (Czech Republic) as indicated by the biomarkers skeletal fluoride content and dental fluorosis.

    Science.gov (United States)

    Kierdorf, Uwe; Bahelková, Petra; Sedláček, František; Kierdorf, Horst

    2012-01-01

    Wild deer have been recommended as bioindicators of fluoride pollution. We compared bone fluoride concentrations and prevalence and severity of dental fluorosis in free-ranging European roe deer (Capreolus capreolus) and red deer (Cervus elaphus) from five counties in the northwestern part of the Czech Republic that had been collected by hunters and whose mandibles were presented at trophy exhibitions in the years 1996/1997 ("early period") and 2009 ("late period"). Data on atmospheric fluoride deposition suggested that the deer from the early period had been exposed to markedly higher fluoride levels than those from the late period. We therefore predicted a decline in skeletal fluoride levels and prevalence of dental fluorosis for both species from the early to the late period. Fluoride concentrations were determined in the coronoid process of the mandible, and assessment of dental fluorosis was performed on the permanent cheek teeth. A pronounced drop in fluoride concentrations from the early period (roe deer (n = 157), median: 3147 mg F(-)/kg of dry bone; red deer (n = 127), median: 1263 mg F(-)/kg of dry bone) to the late period (roe deer (n = 117), median: 350 mg F(-)/kg of dry bone; red deer (n = 72), median: 288 mg F(-)/kg of dry bone) was recorded. Prevalence of dental fluorosis also markedly declined from the early to the late period (roe deer: from 93% to 12%, red deer: from 87% to 28%). The reduction of fluoride deposition in the study area and, in consequence, fluoride exposure of the resident deer populations, is attributed largely to the implementation of emission control devices in the brown coal-fired power plants located in North Bohemia from the mid 1990s onwards. The findings of the present study demonstrate that wild deer are well suited for monitoring temporal changes in fluoride pollution of their habitats. PMID:22137477

  5. Observation of color center peaks in calcium fluoride

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, T. [LeRoy Eyring Center for Solid State Science, Arizona State University, Tempe, AZ 85287-1704, USA (United States); Garvie, L.A.J. [School of Earth and Space Exploration, Arizona State University, Tempe, AZ 85287-1404 (United States); Rez, P., E-mail: Peter.Rez@asu.edu [Department of Physics, Arizona State University, Tempe, AZ 85287-1504 (United States)

    2015-06-15

    Alkali halides such as calcium fluoride all have color center defects that absorb light in the visible region. Using a moncochromator equipped, aberration corrected, scanning transmission electron microscope (STEM) we recorded spectra showing the time evolution of the generation of F and H centers in calcium fluoride. The final stage of electron beam irradiation is the formation of metallic calcium nanoparticles. High resolution low loss spectra for the Vacuum Ultraviolet region were also recorded. - Highlights: • Color center defects clearly identified by high resolution EELS of CaF{sub 2}. • Both F Centers and H Centers produced by electron beam irradiation. • Ultimately metallic calcium is left as evidenced by plasmon and density of states. • High resolution low loss (VUV) spectra also recorded.

  6. Observation of color center peaks in calcium fluoride

    International Nuclear Information System (INIS)

    Alkali halides such as calcium fluoride all have color center defects that absorb light in the visible region. Using a moncochromator equipped, aberration corrected, scanning transmission electron microscope (STEM) we recorded spectra showing the time evolution of the generation of F and H centers in calcium fluoride. The final stage of electron beam irradiation is the formation of metallic calcium nanoparticles. High resolution low loss spectra for the Vacuum Ultraviolet region were also recorded. - Highlights: • Color center defects clearly identified by high resolution EELS of CaF2. • Both F Centers and H Centers produced by electron beam irradiation. • Ultimately metallic calcium is left as evidenced by plasmon and density of states. • High resolution low loss (VUV) spectra also recorded

  7. Sources of carrier F-19 in F-18 fluoride

    Science.gov (United States)

    Link, J. M.; Shoner, S. C.; Krohn, K. A.

    2012-12-01

    Fluorine-18 is used for many PET radiopharmaceuticals. Theoretically 18F should be carrier free and a good candidate for nanochemistry. However, 18F has 10 to 1000 times more stable fluorine atoms than radioactive atoms. In order to understand the source of carrier fluoride and other ions associated with 18F radiosynthesis, anion concentrations of different components of 18F target systems as well as solvents and chemicals used in radiosynthesis were measured. Results: The enriched water used for production of 18F had low levels of anions. In general, the sources of anions, particularly of fluoride, were the chemical reagents used for synthesis and trace contaminants in tubing, valves and fittings. A major component of contamination was nitrate from irradiation of dissolved nitrogen gas in the target water.

  8. Sources of carrier F-19 in F-18 fluoride

    Energy Technology Data Exchange (ETDEWEB)

    Link, J. M.; Shoner, S. C.; Krohn, K. A. [University of Washington, Department of Radiology, Molecular Imaging Center, 1959 NE Pacific St., Box 356004, Seattle, WA 98195-6004 (United States)

    2012-12-19

    Fluorine-18 is used for many PET radiopharmaceuticals. Theoretically {sup 18}F should be carrier free and a good candidate for nanochemistry. However, {sup 18}F has 10 to 1000 times more stable fluorine atoms than radioactive atoms. In order to understand the source of carrier fluoride and other ions associated with {sup 18}F radiosynthesis, anion concentrations of different components of {sup 18}F target systems as well as solvents and chemicals used in radiosynthesis were measured. Results: The enriched water used for production of {sup 18}F had low levels of anions. In general, the sources of anions, particularly of fluoride, were the chemical reagents used for synthesis and trace contaminants in tubing, valves and fittings. A major component of contamination was nitrate from irradiation of dissolved nitrogen gas in the target water.

  9. Determination of boron, silica, fluoride, MBAS, phenols, cyanide and sulphide

    International Nuclear Information System (INIS)

    This study forms part of the NIWR's series of interlaboratory comparison studies involving southern African laboratories engaged in water and wastewater analysis, and is concerned with the analysis of synthetic water samples by 31 laboratories for boron, silica, fluoride, methylene blue active substances (MBAS), phenols, cyanide and sulphide. The results obtained are evaluated and discussed. Recognised standard methods, or modifications of these methods, were used for most of the determinations. Results from the boron, silica and fluoride determinations showed, in general, acceptable accuracy and precision. Results from the MBAS, phenols, cyanide and sulphide determinations were, however, somewhat widespread, and illustrated the difficulty in obtaining reliable results from the measurement of relatively low levels of these determinands

  10. Poly(vinylidene fluoride)/Clay Nanocomposites by Melt Compounding

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The crystalline structures, morphologies, and mechanical properties of poly(vinylidene fluoride)/clay nanocomposites were studied using X-ray diffraction(XRD), transmission electron microscopy(TEM), Fourier transform infrared spectroscopy(FTIR), polarized optical microscopy(POM), and tensile tests. The results of XRD and TEM show that organoclays are dispersed in the poly(vinylidene fluoride)(PVDF) matrix. A clay-induced crystal transformation from α-phase to β-phase of PVFD was confirmed by XRD and FTIR. Clay layers restricted the growth of spherulite. The tensile tests indicate that the tensile modulus and yield strength as well as the elongation at break decrease when clay is loaded.

  11. Trabecular stress fractures during fluoride therapy for osteoporosis

    Energy Technology Data Exchange (ETDEWEB)

    Schnitzler, C.M.; Solomon, L.

    1985-10-01

    Joint pain and swelling in patients on fluoride therapy are generally attributed to rheumatic phenomena; however, their occurrence exclusively in the lower limbs suggests a mechanical cause. Eight patients receiving daily doses of sodium fluoride 1.09 mg/kg, elemental calcium 1 gm, and vitamin D 1000-2800 units for osteoporosis spontaneously developed 17 episodes of periarticular pain and swelling in the lower limbs. Radiographs taken within two weeks of the onset of pain were negative, but when repeated 4-6 weeks later showed features of healing stress fractures in the periarticular cancellous bone at the following sites: distal femur (2) proximal tibia (3), distal tibia (6), calcaneum (6). Bone scintigraphy was positive on five occasions, two before radiographic signs had appeared. (orig.).

  12. Plant tissue hybrid electrode for determination of phosphate and fluoride

    Energy Technology Data Exchange (ETDEWEB)

    Schubert, F.; Renneberg, R.; Scheller, F.W.; Kirstein, L.

    1984-08-01

    A biosensor for inorganic phosphate and fluoride has been developed by coupling a potato (Solanum tuberosum) tissue slice and immobilized glucose oxidase with a Clark oxygen electrode. Measurement is based on the inhibition by either ion of potato acid phosphates catalyzed glucose 6-phosphate hydrolysis. The precision is 1.7% and 6.5% and the lower detection limit 2.5 X 10/sup -5/ M and 1 X 10/sup -4/ M for phosphate and fluoride, respectively. For phosphate determination the hybrid sensor is stable for 28 days or 300 assays. With a higher limit of detection the sensor can be applied in a commercial enzyme electrode based device. Its application for phosphate determination in fertilizer and urine samples is described.

  13. Some metallic materials and fluoride salts for high temperature applications

    International Nuclear Information System (INIS)

    There has been a special Ni base alloy MONICR for high temperature applications in fluoride salt environments developed in the framework of the complex R and D program for the Molten Salt Reactor (MSR) - SPHINX (SPent Hot fuel Incinerator by Neutron fluX) concept development in the Czech Republic. Selected results of MONICR alloy tests and results of semi products fabrication from this alloy are discussed in the paper. The results of the structural materials tests are applied on semi-products and for the design of the testing devices as the autoclave in loop arrangement for high temperature fluoride salts applications. Material properties other Ni base alloys are compared to those of MONICR. Corrosion test results of the alloy A686 in the LiF - NaF - ZrF4 molten salt are provided and compared to the measured values of the polarizing resistance. (author)

  14. Determination of fluoride in coal using pyrohydrolysis for analyte separation

    Energy Technology Data Exchange (ETDEWEB)

    Dressler, V.L.; Pozebon, D.; Flores, E.L.M.; Paniz, J.N.G.; Flores, E.M.M. [Federal University of Santa Maria, Santa Maria (Brazil)

    2003-04-01

    A method for the determination of fluoride in coal using pyrohydrolysis for sample decomposition is proposed. An apparatus was constructed, and the influence of vanadium pentoxide (V{sub 2}O{sub 5}) as a catalyst for the pyrohydrolysis reaction was investigated. It was verified that V{sub 2}O{sub 5} does not influence the release of fluoride from coal. Certified and non-certified samples were analysed using an ion selective electrode (ISE) for analyte detection. Precise (RSD < 7%) and accurate ( recovery in accordance with certified values) results were obtained. The limit of quantification (LOQ) of the method was 5.0 {mu}gF/g of sample, using 20 mg of sample and a final dilution to 10 mL. The sample frequency was 5 samples h{sup -1}.

  15. Impact of a modified carbonated beverage on human dental plaque and salivary pH: An in vivo study

    OpenAIRE

    Sardana, V.; A Y Balappanavar; G B Patil; Kulkarni, N; S G Sagari; Gupta, K.D.

    2012-01-01

    Background: To assess the plaque and salivary pH changes at different time intervals in vivo after consumption of a carbonated beverage modified with sodium fluoride and calcium phosphate. Materials and Methods: Twenty-four subjects aged 18-25 years were recruited and randomly assigned to three groups (group A, original drink sprite; group B, sprite with sodium fluoride; group C, sprite with calcium phosphate). Collection of pooled plaque and unstimulated saliva was done before and after the ...

  16. [Study on ecological risk assessment technology of fluoride pollution from arid oasis soil].

    Science.gov (United States)

    Xue, Su-Yin; Li, Ping; Wang, Sheng-Li; Nan, Zhong-Ren

    2014-03-01

    According to translocation regulation of fluoride in the typical oasis soil-plant system under field, an ecological risk assessment model of fluoride was established, and this model was used to assess ecological risk to fluoride pollution from suburban oasis soils in Baiyin City, which was specifically expressed with the potential ecological risk of bioavailability (ER(bc)) model to assess ecological risk of fluoride pollution in oasis regions. Results showed that the ecological risk indices of fluoride pollution from this region were 1.37-24.81, the level of risk at most sites was high to very high, the average ecological risk index was 11.28, belonged to very high risk. This indicated that in the suburb soil of Baiyin City needs to be concerned about the remediation of fluoride pollution. PMID:24881399

  17. Growth kinetics of calcium fluoride at high supersaturation in a fluidized bed reactor.

    Science.gov (United States)

    Jiang, K; Zhou, K G; Yang, Y C; Du, H

    2014-01-01

    Crystallization process in a fluidized bed reactor (FBR) has been regarded as an environmentally friendly technology for the removal and recovery of fluoride from industrial wastewater. The growth kinetics of calcium fluoride at high supersaturation was studied for design, control, and operation of an FBR. The main variables, including supersaturation, superficial velocity, pH value, and particle size of seed that influenced the crystal growth were investigated. Then, a growth model was used to predict the linear growth rate of calcium fluoride at a high influent concentration of fluoride. The pressure difference in the FBR was used as a feature to characterize the growth rate of calcium fluoride. The aggregation and adsorption between seeds and fine particles were proven to be a possible mechanism for growth of calcium fluoride.

  18. CONTRIBUTION OF MACROSCOPIC DIMENSION EFFECT TO PIEZOELFCTRICITY IN POLYVINYLIDENE FLUORIDE

    Institute of Scientific and Technical Information of China (English)

    WEN Jianxun; TAKEO FURUKAWA

    1987-01-01

    In this paper, we have studied the piezoelectricity in the poled uniaxially drawn polyvinylidene fluoride. The piezoelectric constants d31, d32, da33 and Young's moduli 1/s11 and 1/s22 have been determined as a function of the remanent polarization Pr. The piezoelectric constants of the samples show a strong in-plane anisotropy. Such an anisotropy is mostly attributable to different Poisson's ratio. It is found that the piezoelectric activity mainly arises from macroscopic dimensional change.

  19. Vibrational Modes Analysis of Poly (Vinylidene Fluoride-Trifluoroethylene)

    Institute of Scientific and Technical Information of China (English)

    李吉超; 王春雷; 钟维烈; 李正法

    2003-01-01

    The ground state geometry and vibrational modes of poly (vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)]molecular chains have been investigated by ab initio molecular orbital calculation. The gauche bonds in P(VDFTrFE) are introduced by TrFE monomers. The vibrational modes are localized within all-trans segments. These results cause the infrared absorption weaker and diffused, and may be responsible for dielectric relaxation of the copolymers.

  20. Preparation of Polyvinylidene Fluoride (PVDF) Hollow Fiber Hemodialysis Membranes

    OpenAIRE

    Qinglei Zhang; Xiaolong Lu; Lihua Zhao

    2014-01-01

    In this study, the polyvinylidene fluoride (PVDF) hollow fiber hemodialysis membranes were prepared by non-solvent induced phase separation (NIPS). The influences of PVDF membrane thickness and polyethylene glycol (PEG) content on membrane morphologies, pore size, mechanical and permeable performance were investigated. It was found that membrane thickness and PEG content affected both the structure and performance of hollow fiber membranes. The tensile strength and rejection of bovine serum a...

  1. Physico-Mechanical Properties of New Electrospun Polyvinylidene Fluoride Nanocomposites

    OpenAIRE

    Ramadan, Ahmed Abdelatty Issa

    2015-01-01

    This study aimed to prepare and characterize poly(vinylidene fluoride) (PVDF) nanofibres with the following additives: graphene oxide (GO), cellulose, and silver nanoparticles (Ag-NPs). Two types of solvents were used to prepare the virgin and composite materials: acetone and DMF, which lead to a porous surface of the nanofibres. Effect of combination of the additives and the effect of two salts (sodium chloride and tetraethyl ammonium chloride) was also considered. These nanofibres were prod...

  2. Ion transport in alkaline and earth alkaline hydrogen fluorides

    NARCIS (Netherlands)

    Kroger, C; Niggemeier, H; Wiemhofer, HD; Glumov, O; Murin, [No Value

    2002-01-01

    The impedance of the hydrogen fluorides KHF2, NH4HF2 and BaHF3 was investigated as a function of temperature and in the presence of HF and H2O. A comparison of results on different electrode materials. (graphite, silver, palladium, Sn \\ SnF2, and Sn \\ SnF2 \\ LaF3) was used to elucidate the contribut

  3. Arsenic and fluoride in the groundwater of Mexico.

    Science.gov (United States)

    Armienta, M A; Segovia, N

    2008-08-01

    Concentrations of arsenic and fluoride above Mexican drinking water standards have been detected in aquifers of various areas of Mexico. This contamination has been found to be mainly caused by natural sources. However, the specific processes releasing these toxic elements into groundwater have been determined in a few zones only. Many studies, focused on arsenic-related health effects, have been performed at Comarca Lagunera in northern México. High concentrations of fluoride in water were also found in this area. The origin of the arsenic there is still controversial. Groundwater in active mining areas has been polluted by both natural and anthropogenic sources. Arsenic-rich minerals contaminate the fractured limestone aquifer at Zimapán, Central México. Tailings and deposits smelter-rich fumes polluted the shallow granular aquifer. Arsenic contamination has also been reported in the San Antonio-El Triunfo mining zone, southern Baja California, and Santa María de la Paz, in San Luis Potosí state. Even in the absence of mining activities, hydrogeochemistry and statistical techniques showed that arsenopyrite oxidation may also contaminate water, as in the case of the Independencia aquifer in the Mexican Altiplano. High concentrations of arsenic have also been detected in geothermal areas like Los Azufres, Los Humeros, and Acoculco. Prevalence of dental fluorosis was revealed by epidemiological studies in Aguascalientes and San Luis Potosí states. Presence of fluoride in water results from dissolution of acid-volcanic rocks. In Mexico, groundwater supplies most drinking water. Current knowledge and the geology of Mexico indicate the need to include arsenic and fluoride determinations in groundwater on a routine basis, and to develop interdisciplinary studies to assess the contaminant's sources in all enriched areas.

  4. Arsenic and fluoride in the groundwater of Mexico.

    Science.gov (United States)

    Armienta, M A; Segovia, N

    2008-08-01

    Concentrations of arsenic and fluoride above Mexican drinking water standards have been detected in aquifers of various areas of Mexico. This contamination has been found to be mainly caused by natural sources. However, the specific processes releasing these toxic elements into groundwater have been determined in a few zones only. Many studies, focused on arsenic-related health effects, have been performed at Comarca Lagunera in northern México. High concentrations of fluoride in water were also found in this area. The origin of the arsenic there is still controversial. Groundwater in active mining areas has been polluted by both natural and anthropogenic sources. Arsenic-rich minerals contaminate the fractured limestone aquifer at Zimapán, Central México. Tailings and deposits smelter-rich fumes polluted the shallow granular aquifer. Arsenic contamination has also been reported in the San Antonio-El Triunfo mining zone, southern Baja California, and Santa María de la Paz, in San Luis Potosí state. Even in the absence of mining activities, hydrogeochemistry and statistical techniques showed that arsenopyrite oxidation may also contaminate water, as in the case of the Independencia aquifer in the Mexican Altiplano. High concentrations of arsenic have also been detected in geothermal areas like Los Azufres, Los Humeros, and Acoculco. Prevalence of dental fluorosis was revealed by epidemiological studies in Aguascalientes and San Luis Potosí states. Presence of fluoride in water results from dissolution of acid-volcanic rocks. In Mexico, groundwater supplies most drinking water. Current knowledge and the geology of Mexico indicate the need to include arsenic and fluoride determinations in groundwater on a routine basis, and to develop interdisciplinary studies to assess the contaminant's sources in all enriched areas. PMID:18335171

  5. Amelioration of Fluoride Toxicity with the Use of Indigenous Inputs

    OpenAIRE

    Maitra A; Datta J.K.; Mondal N.K.

    2013-01-01

    An assessment was undertaken to study the efficacy of bacterial consortia isolated from different sources viz. rhizosphere of rice plant, oil spill sites of a petrol pump and from the sludge of a pharmaceutical waste water drain against the impact of fluoride. The experiments were conducted with two crops. In this mung bean experiment Vigna radiata was selected as a test crop. The seeds were sown in the field with bacterial consortia, compost and reduced dose (25% less nitrogen than recommend...

  6. Tokyo dark matter search experiment with lithium fluoride bolometer

    International Nuclear Information System (INIS)

    An experiment to search for hypothetical neutralino dark matter using lithium fluoride bolometer array is underway. This bolometer array consists of eight pieces of 21 g LiF bolometers. Fluorine has large sensitivity for axially coupled neutralino compared with other nuclei. We report on the first results from the pilot run in a shallow depth site (15 m w.e.). From the measured energy spectra the exclusion limits for the cross section of the elastic neutralino scattering off protons are evaluated

  7. The effects of airborne fluorides on oral conditions in Morocco

    Energy Technology Data Exchange (ETDEWEB)

    Haikel, Y.; Cahen, P.M.; Turlot, J.C.; Frank, R.M. (Universite Louis Pasteur, Strasbourg (France))

    1989-08-01

    The purpose of this study was to determine the prevalence and severity of dental caries and dental fluorosis, as well as various other oral conditions, in 2378 subjects (ages seven to 60) living in the fluoridated area of Khouribga and the non-fluoridated area of Beni Mellal, Morocco. The community index of dental fluorosis (CFI) ranged from 1.99 to 2.80 in the high-fluoride area: Over 90% of the population was affected, and more than one-third of the subjects showed moderate dental fluorosis. However, in Beni Mellal, more than 96% of the dentate subjects examined were free of dental fluorosis, and the CFI of 0.02 was considered not significant. Significant differences were observed between the two areas with respect to caries prevalence. DMFT and DMFS indices were markedly lower in the fluorosis area of Khouribga. The oral conditions of subjects appeared to be better in Khouribga, where the gingival and calculus indices were significantly lower than in Beni Mellal. The analyses of covariance showed no significant differences in plaque accumulation (PI) between the Khouribga and Beni Mellal samples. However, a close statistical correlation was found between PI and GI in Beni Mellal and Khouribga.

  8. Calix[4]arene-Based New Neutral Sensors for Fluoride

    Institute of Scientific and Technical Information of China (English)

    LIU,Shun-Ying; MENG,Ling-Zhi; LIU,Xin; HE,Yong-Bing

    2004-01-01

    @@ The development of new receptors which can recognize neutral and charged species has attracted considerable interest in the recent past.[1] Anions such as fluoride, chloride, phosphate and carboxylate play crucial roles in a range of biological phenomena and are implicated in many disease states.[2] Investigations on molecular and/or ionic recognition by calixarenes and their derivatives as synthetic receptors have attracted increasing attention in supramolecular chemistry because of their modifiable structure.[3] However, calix[4]arenes-based neutral receptors containing thiourea and amide groups are still rare. In this paper, we report fluoride selective optical chemosensors 4 and 5, based on calix[4]arene thiourea and amide derivatives, which only show a remarkable absorption change in the presence of fluoride ions, while have no any change upon addition of other anions (Cl- Br-, I-, AcO- and H2PO4-). The association constants are 947 and 2883 mol·L-1, respectively. The synthesis of calix[4]arene derivatives 4 and 5 is outlined in the following Scheme 1.

  9. Immunotoxic effects of fluoride on the hemocytes of Venerupis philippinarum

    Directory of Open Access Journals (Sweden)

    L Ballarin

    2014-01-01

    Full Text Available The increasing levels of fluoride in the aquatic environments is a matter of concern for freshwater and marine ecosystems. Although data on fluoride toxicity to aquatic organisms are increasing in the scientific literature, few data are available regarding the effects, at cellular level, on freshwater or marine invertebrates. In the present paper, we present data on the effects of in vitro exposure to sodium fluoride (NaF on the hemocytes of the Manila clam Venerupis philippinarum. Results indicate that NaF reduces cell spreading and phagocytosis in a dose-dependent way, through the alteration of the actin cytoskeleton. In addition, the compound decreases the stability of the lysosomal membranes, as revealed by the Neutral Red assay. In addition, the observed increase in hemocyte mortality and the parallel rise in DNA fragmentation inside their nuclei, as revealed by the TUNEL assay, suggest a NaF-dependent induction of apoptosis, in accordance with the capability of NaF to induce oxidative stress, a known cause of apoptosis, As hemocytes represent the major defence weapon against foreign, potentially pathogenic microbes, the above results indicate a negative effect of NaF on the immune status of V. philippinarum.

  10. Characterization and biocompatibility of fluoridated biphasic calcium phosphate ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Z.L. [State Key Laboratory of Oral Diseases, West China Hospital of Stomatology, Sichuan University, Chengdu 610041 (China); Yu, H.Y. [State Key Laboratory of Oral Diseases, West China Hospital of Stomatology, Sichuan University, Chengdu 610041 (China)], E-mail: yhyang6812@tfol.com; Zeng, Q. [Institute for Nanobiomedical Technology and Membrane Biology, Sichuan University, Chengdu 610041 (China); He, H.W. [State Key Laboratory of Oral Diseases, West China Hospital of Stomatology, Sichuan University, Chengdu 610041 (China)

    2008-11-15

    Biphasic calcium phosphate ceramics (BCP) has been widely used in tooth and bone implants due to its excellent biocompatibility. Incorporation of fluorine ions in BCP has drawn much attention because of the beneficial role played by the fluorine ions in bone and tooth growth. The aim of this study was to obtain fluoridated biphasic calcium phosphate (FBCP) by immersing BCP into saturated ZnF{sub 2} solution with F{sup -} concentration of 3500 mg/l at different times. The phase and incorporation of fluoride into BCP were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM). The biomineralization and influence of FBCP on osteoblastic behavior were evaluated and compared with that of biphasic calcium phosphate (BCP). The results exhibited that the phase evolution of the BCP was affected by the fluoride incorporation and the FBCP significantly improved the differentiation and proliferation of osteoblasts. These findings suggest that the FBCP would be very useful as a bone reconstructive material.

  11. In vivo efficacy of tamarind (Tamarindus indica) fruit extract on experimental fluoride exposure in rats.

    Science.gov (United States)

    Dey, S; Swarup, D; Saxena, Anju; Dan, Ananya

    2011-12-01

    The study was undertaken to determine the efficacy of hydro-methanolic (1:1) extract of tamarind (Tamarindus indica L.) fruit pulp in removing body fluoride burden. Thirty rats were divided into five groups. Keeping no fluoride group as the control, rats of no treatment, low dose, middle dose and high dose groups received sodium fluoride orally at the rate of 200mg per kg body weight daily for 14 weeks. Rats of low dose, middle dose and high dose group simultaneously received tamarind fruit pulp extract at three doses, viz. 25 (low), 50 (medium) and 100mg (high) per kg body weight orally, respectively. Fluoride concentration in blood, urine and long bone of experimental rats was monitored to assess the efficacy of the extract. Mean serum fluoride concentration in fluoride exposed rats was 0.145 ± 0.009 and 0.783 ± 0.042 μg/ml on days 0 and 98. In comparison, fluoride concentrations in tamarind treated rats were 0.179 ± 0.021 and 0.633 ± 0.015; 0.179 ± 0.021 and 0.502 ± 0.025 and 0.176 ± 0.021 and 0.498 ± 0.030 μg/ml in low, medium and high dose groups, respectively on day 0 and day 98 of the experiment. There was a significant (p ≤ 0.01) increase in urinary fluoride excretion from day 28 onwards. The mean fluoride concentration in long bones of treated rats was significantly lower than the values recorded in fluoride exposed rats. These findings suggest that concomitant use of tamarind fruit pulp extract can reduce fluoride concentration in blood and bone and enhanced urinary excretion, indicating the ameliorative potential of fruits of tamarind in fluoride toxicity.

  12. Fluorides for the prevention of early tooth decay (demineralised white lesions) during fixed brace treatment

    OpenAIRE

    Benson, P.E.; Parkin, N.; Dyer, F.; Millett, D. T.; Furness, S.; P. Germain

    2013-01-01

    Demineralised white lesions (DWLs) can appear on teeth during fixed brace treatment because of early decay around the brackets that attach the braces to the teeth. Fluoride is effective in reducing decay in susceptible individuals in the general population. Individuals receiving orthodontic treatment may be prescribed various forms of fluoride treatment. This review compares the effects of various forms of fluoride used during orthodontic treatment on the development of DWLs. This is an updat...

  13. Fluoride Plus Functionalized β-TCP: A Promising Combination for Robust Remineralization

    OpenAIRE

    Karlinsey, R.L.; Pfarrer, A.M.

    2012-01-01

    With more than 50 years of clinical success, fluoride serves as the gold standard agent for preventing tooth decay. In particular, the action of fluoride facilitates saliva-driven remineralization of demineralized enamel and alters solubility beneficially. Still, tooth decay remains problematic, and one way to address it may be through the development of new mineralizing agents. Laboratory and clinical studies have demonstrated that the combination of fluoride and functionalized β-tricalcium ...

  14. Fluoride: A naturally-occurring health hazard in drinking-water resources of Northern Thailand.

    Science.gov (United States)

    Chuah, C Joon; Lye, Han Rui; Ziegler, Alan D; Wood, Spencer H; Kongpun, Chatpat; Rajchagool, Sunsanee

    2016-03-01

    In Northern Thailand, incidences of fluorosis resulting from the consumption of high-fluoride drinking-water have been documented. In this study, we mapped the high-fluoride endemic areas and described the relevant transport processes of fluoride in enriched waters in the provinces of Chiang Mai and Lamphun. Over one thousand surface and sub-surface water samples including a total of 995 collected from shallow (depth: ≤ 30 m) and deep (> 30 m) wells were analysed from two unconnected high-fluoride endemic areas. At the Chiang Mai site, 31% of the shallow wells contained hazardous levels (≥ 1.5 mg/L) of fluoride, compared with the 18% observed in the deep wells. However, at the Lamphun site, more deep wells (35%) contained water with at least 1.5mg/L fluoride compared with the shallow wells (7%). At the Chiang Mai site, the high-fluoride waters originate from a nearby geothermal field. Fluoride-rich geothermal waters are distributed across the area following natural hydrological pathways of surface and sub-surface water flow. At the Lamphun site, a well-defined, curvilinear high-fluoride anomalous zone, resembling that of the nearby conspicuous Mae Tha Fault, was identified. This similarity provides evidence of the existence of an unmapped, blind fault as well as its likely association to a geogenic source (biotite-granite) of fluoride related to the faulted zone. Excessive abstraction of ground water resources may also have affected the distribution and concentration of fluoride at both sites. The distribution of these high-fluoride waters is influenced by a myriad of complex natural and anthropogenic processes which thus created a challenge for the management of water resources for safe consumption in affected areas. The notion of clean and safe drinking water can be found in deeper aquifers is not necessarily true. Groundwater at any depth should always be tested before the construction of wells.

  15. Acceptability of Salt Fluoridation in a Rural Latino Community in the United States: An Ethnographic Study

    Science.gov (United States)

    Barker, Judith C.; Hoeft, Kristin S.

    2016-01-01

    Compared to other population groups in the United States, caries (tooth decay) is a disproportionately prevalent disease among Latino populations, especially among low-income and rural sub-groups and children under five years of age. Fluoride is a primary preventive for caries. While water fluoridation is a major and effective public health means for delivering fluoride on a mass scale, it does not reach many rural areas or population groups such as Latinos who eschew drinking water from municipal sources. This study examines the acceptability to such groups of salt fluoridation, an alternate means of delivering fluoride long used on a global scale. An ethnographic study in California’s rural Central Valley was performed. Thirty individual interviews and 5 focus groups (N = 61) were conducted in Spanish to investigate low-income Latino migrant caregivers’ experiences, views and understandings of domestic salt, oral health, caries prevention and fluoride. Audio data were transcribed, translated, coded and thematically analyzed. Table salt was readily available and frequently consumed. Both adult and child daily sodium consumption was high. Despite a general feeling that it was good, and present in dentifrices or dietary supplements, most participants had little knowledge about fluoride. Concerns were raised about cardio-vascular and other possibly deleterious effects if an increase in salt consumption occurred because fluoridated salt was viewed as having ‘extra’ benefits. Once informed about fluoride’s safety and role in caries prevention, most participants expressed willingness to use fluoridated salt, especially if it benefitted children. Reassurance about its safety and benefits, and demonstration of its taste, were important aspects of acceptance. Taste was paramount. Participants would not consume more fluoridated salt than their current salt as that would result in unpleasant changes in food flavor and taste. While salt fluoridation is acceptable

  16. [Comparative in vitro evaluation of modern glass ionomer cements for adhesion strength and fluoride release].

    Science.gov (United States)

    Zhitkov, M Yu; Rusanov, F S; Poyurovskaya, I Ya

    2016-01-01

    The study proved similar adhesion strength and fluoride release level in aqueous extracts of glass ionomer cements Cemion (VladMiVa, Russia), Glassin Rest (Omega-Dent, Russia), Cemfil 10 (StomaDent, Russia) and Fuji VIII (GC Corporation, Japan). Despite of close concentrations of fluoride in glasses, the rate of fluoride release in water from calcium and calcium-barium glasses is much higher than that of strontium glasses. PMID:27239999

  17. Feasibility and costs of water fluoridation in remote Australian Aboriginal communities

    Directory of Open Access Journals (Sweden)

    Ehsani Jonathon P

    2007-06-01

    Full Text Available Abstract Background Fluoridation of public water supplies remains the key potential strategy for prevention of dental caries. The water supplies of many remote Indigenous communities do not contain adequate levels of natural fluoride. The small and dispersed nature of communities presents challenges for the provision of fluoridation infrastructure and until recently smaller settlements were considered unfavourable for cost-effective water fluoridation. Technological advances in water treatment and fluoridation are resulting in new and more cost-effective water fluoridation options and recent cost analyses support water fluoridation for communities of less than 1,000 people. Methods Small scale fluoridation plants were installed in two remote Northern Territory communities in early 2004. Fluoride levels in community water supplies were expected to be monitored by local staff and by a remote electronic system. Site visits were undertaken by project investigators at commissioning and approximately two years later. Interviews were conducted with key informants and documentation pertaining to costs of the plants and operational reports were reviewed. Results The fluoridation plants were operational for about 80% of the trial period. A number of technical features that interfered with plant operation were identified and addressed though redesign. Management systems and the attitudes and capacity of operational staff also impacted on the effective functioning of the plants. Capital costs for the wider implementation of these plants in remote communities is estimated at about $US94,000 with recurrent annual costs of $US11,800 per unit. Conclusion Operational issues during the trial indicate the need for effective management systems, including policy and funding responsibility. Reliable manufacturers and suppliers of equipment should be identified and contractual agreements should provide for ongoing technical assistance. Water fluoridation units should

  18. Fluoride removal from drinking water by adsorption using bone char as a biosorbent

    OpenAIRE

    Ma, W; Ya, F.; Wang, R.; Zhao, Y. Q.

    2008-01-01

    As a biomass material, bone char was investigated for the feasibility to be used as a cost-effective biosorbent for fluoride removal from drinking water in groundwater environment. Based on the batch tests with natural tourmalin and active alumina being the reference adsorbents, BF (referring to bone char) has demonstrated a higher fluoride adsorption capacity. This capacity was found being increased with the increase of fluoride concentration. Furthermore, BF based column adsorption experime...

  19. Method for routine determination of fluoride in urine by selective ion- electrode

    International Nuclear Information System (INIS)

    A simple, fast and sensitive method is outlined for determining fluoride in urine of workers who handle fluoride compounds. The determination is based on the measurement of fluoride by ion selective electrode. Cationic interferents like Ca++, Mg++, Fe+++ and Al+++ are complexed by EDTA and citric acid. Common anions present in urine, such as Cl-, PO---4 and SO--4 do not interfere in the method. (Author)

  20. Historical biomonitoring of fluoride pollution by determining fluoride contents in roe deer (Capreolus capreolus L.) antlers and mandibles in the vicinity of the largest Slovene thermal power plant.

    Science.gov (United States)

    Jelenko, Ida; Pokorny, Boštjan

    2010-12-15

    Roe deer antlers/mandibles are a useful tool for determination of ambient fluoride pollution. Antlers have a well-defined annual cycle of growth, therefore they represent a natural standardisation of samples during winter months. On the contrary, mandibles accumulate fluorides during the whole life of an organism, thus they reflect aggregated effect of fluoride pollution trough the life-span of an organism. Both tissues are easily available; mandibles are often systematically collected with the purpose of cognitive management and control, and antlers could be gathered from private well-dated hunters' collections. Considering these benefits, fluoride contents were measured in 141 antlers (period 1960-2007) and 220 mandibles (period 1997-2009) of roe deer, shot in the vicinity of the largest Slovene Thermal Power Plant of Šoštanj (ŠTPP) as one of the major sources of fluorides in Slovenia. Fluoride contents in antlers significantly differed among age categories, and ranged from 110 to 1210 mg/kg in yearlings, 130 to 2340 mg/kg in young adults, and 250 to 2590 mg/kg in older adults, respectively. Fluoride levels in mandibles were also significantly different among age categories, and ranged from 30.0 to 227 mg/kg in fawns, 33.8 to 383 mg/kg in yearlings, and 61.5 to 1020 mg/kg in adults, respectively. Comparison of these results with previously reported fluoride contents in antlers and mandibles of roe deer from different areas of Europe revealed that the study area has never been extensively contaminated with fluorides. Moreover, trends of fluoride contents in both tissues confirmed a significant decrease of fluoride pollution in the area after the years 1995 and 2000, when flue-gas cleaning devices were constructed on the ŠTPP. Indeed, highly positive correlations between annual emissions from the ŠTPP and mean annual fluoride contents in antlers/mandibles confirmed that both tissues may be a useful tool for assessing temporal trends in ambient fluoride

  1. Electrochemistry of thorium fluoride in LiCl-KCl eutectic melts and methodology for speciation studies with fluorides ions

    International Nuclear Information System (INIS)

    This paper reports the electrochemical behavior of ThF4 in LiCl-KCl molten salt. It proposes a potentiometric method to determine the complexation constants of thorium (IV) with fluorides. The knowledge of these constants leads to calculate the speciation diagram of Th(IV) species as a function of the concentration of fluoride ions in the salt. These results were extrapolate to give an estimation of the activity coefficient of ThF4 in the molten salt LiF-ThF4 (77.5-22.5 mol%). This salt is retained for the molten salt fast reactor system, currently studied as a Generation IV concept in the domain of nuclear energy

  2. Effects of Fluoride on Lipid Peroxidation, DNA Damage and Apoptosis in Human Embryo Hepatocytes

    Institute of Scientific and Technical Information of China (English)

    AI-GUO WANG; TAO XIA; QI-LONG CHU; MING ZHANG; FANG LIU; XUE-MIN CHEN; KE-DI YANG

    2004-01-01

    Objective To investigate the effects of fluoride on lipid peroxidation, DNA damage and apoptosis in human embryo hepatocyte L-02 cells. Methods Lipid peroxide (LPO) level, reduced glutathione (GSH) content, DNA damage, apoptosis, and cell cycle analysis were measured after in vitro cultured L-02 cells were exposed to sodium fluoride at different doses (40 μg/mL, 80 μg/mL, and 160 μg/mL) for 24 hours. Results Fluoride caused an increase of LPO levels and a decrease of GSH content in L-02 cells. There appeared to be an obvious dose-effect relationship between the fluoride concentration and the observed changes. Fluoride also caused DNA damage and apoptosis and increased the cell number in S phase of cell cycle in the cells tested. There was a statistically significant difference in DNA damage and apoptosis when comparing the high dose of fluoride treated cells with the low dose of fluoride treated cells. Conclusion Fluoride can cause lipid peroxidation, DNA damage, and apoptosis in the L-02 cell experimental model and there is a significant positive correlation between fluoride concentration and these pathological changes.

  3. A NOVEL BIO-WASTE INCORPORATED ALGINATE SORBENT FOR DE-FLUORIDATION OF WATER

    OpenAIRE

    Carmalin Sophia Ayyappan; Sreeja, S.; V.M. Bhalambaal

    2015-01-01

    This study evaluates the feasibility of using tamarind (Tamarindus indica) seed powder for de-fluoridation of fluoride contaminated water. Batch study confirmed that tamarind seeds in dry powder form could remove 87% of fluoride from water. This bio-sorbent can be used effectively in areas where fluoride concentrations are above the permissible limits of 1.5 mg·l-1 as per WHO Standard, 1984. Tamarind seed powder was incorporated in a matrix of sodium alginate and made into gel-beads. The bead...

  4. Fluoride and nitrate removal from brackish groundwaters by batch-mode capacitive deionization.

    Science.gov (United States)

    Tang, Wangwang; Kovalsky, Peter; He, Di; Waite, T David

    2015-11-01

    Capacitive deionization (CDI) is an emerging water desalination technology in which pairs of porous electrodes are electrically charged to remove ionic species from water. In this work, the feasibility of fluoride and nitrate removal from brackish groundwaters by batch-mode CDI was investigated. Initially, the effects of flow rate, initial fluoride concentration, and initial coexisting NaCl concentration on fluoride removal were studied. The steady-state fluoride concentration declined as the initial fluoride concentration decreased while initial NaCl concentration remained constant. Due to the competitive electrosorption between fluoride and chloride for limited pore surface sites, a higher initial chloride concentration resulted in a higher equilibrium dissolved fluoride concentration. A simplified one-dimensional transport model for dual anions was developed and found to reliably describe the dynamic process of removal of both fluoride and chloride ions in CDI cells over a range of well-defined operating conditions. Based on the ability of the model to describe fluoride removal, it was extended to description of nitrate removal from brackish groundwaters and also found to perform well. Thus, the approach to description of ion removal, at least in batch studies, appears robust and should assist in optimization of design and operating conditions such that optimal removal of trace ionic species is achieved even when high background concentrations of salt are present. PMID:26278188

  5. Development of an empirical model for fluoride removal from photovoltaic wastewater by electrocoagulation process

    KAUST Repository

    Drouiche, Nadjib

    2011-05-01

    Electrocoagulation experiments were conducted with bipolar aluminium electrodes to determine the optimum conditions for the fluoride removal from synthetic photovoltaic wastewater. A high fluoride concentration in community water supplies can cause fluorosis which has a detrimental effect on human health in particular on teeth and bones. A full 23 factorial design of experiments was used to obtain the best conditions of fluoride removal from water solutions. The three factors considered were initial fluoride concentration, applied potential, and supporting electrolyte dosage. Two levels for each factor were used; supporting electrolyte (0 and 100), applied potential (10 and 30 V), and initial fluoride concentration (20 and 25 mg/L). Results showed that the optimum conditions for fluoride removal from photovoltaic wastewater containing an initial fluoride concentration of 20 mg/L were a supporting electrolyte dose of 100 mg/L and an applied potential of 30 V. These gave a residual fluoride concentration of 8.6 mg/L which was below the standard discharge limit. A mathematical equation showing the relation between residual fluoride concentration and the effective variables was also developed. © 2011 Desalination Publications. All rights reserved.

  6. Fluoride Removal From Drinking Water by Electrocoagulation Using Iron and Aluminum Electrodes

    Directory of Open Access Journals (Sweden)

    Takdastan

    2014-07-01

    Full Text Available Background Existence of fluoride in drinking water above the permissible level causes human skeletal fluorosis. Objectives Electrocoagulation by iron and aluminum electrodes was proposed for removing fluoride from drinking water. Materials and Methods Effects of different operating conditions such as treatment time, initial pH, applied voltage, type and number of electrodes, the spaces between aluminum and iron electrodes, and energy consumption during electrocoagulation were investigated in the batch reactor. Variable concentrations of fluoride solution were prepared by mixing proper amounts of sodium fluoride with deionized water. Results Experimental results showed that aluminum electrode is more effective in fluoride removal than iron, as in 40 minutes and initial pH of 7.5 at 20 V, the fluoride removal process reached to 97.86%. The final recommendable limit of fluoride (1.5 mg/L was obtained in 10 minutes at 20 V with the aluminum electrode. Conclusions In electrocoagulation with iron and aluminum electrodes, increase of voltage, number of electrodes and reaction time as well as decrease of the spaces between electrodes, enhanced the fluoride removal efficiency from drinking water. In addition the effect of pH and initial concentration of fluoride varied with types of electrodes.

  7. Fluoride stability in dentifrices stored in schools in a town of northern Brazil

    Directory of Open Access Journals (Sweden)

    Jéssica Bandeira MATIAS

    2015-01-01

    Full Text Available The aim of this study was to analyze fluoride stability in dentifrices stored during nine months in schools from Careiro da Várzea, State of Amazonas, Brazil. Analysis of total fluoride concentration, total soluble fluoride, and ionic fluoride in the dentifrice samples was performed in four different time periods: at the time of purchase (baseline; after three months, after six months, and after nine months of storage. Fluoride concentration was determined using a specific electrode (Orion 96-09 connected to an ion analyzer (Orion A-720 and calibrated with fluoride standard solutions containing 2.0 to 32.0 ppm F. The results obtained during the measurements were analyzed by analysis of variance (one-way ANOVA, followed by Tukey’s test for comparison of the means. After nine months of storage, total soluble fluoride, the active form of fluoride, decreased by 21.9%. As total soluble fluoride was below the minimum required for anticaries efficacy (1,000 ppm F in the fourth analysis, it may be concluded that anticaries potential decreased with storage time.

  8. A critical study on efficiency of different materials for fluoride removal from aqueous media

    Science.gov (United States)

    2013-01-01

    Fluoride is a persistent and non-biodegradable pollutant that accumulates in soil, plants, wildlife and in human beings. Therefore, knowledge of its removal, using best technique with optimum efficiency is needed. The present survey highlights on efficacy of different materials for the removal of fluoride from water. The most important results of extensive studies on various key factors (pH, agitation time, initial fluoride concentration, temperature, particle size, surface area, presence and nature of counter ions and solvent dose) fluctuate fluoride removal capacity of materials are reviewed. PMID:23497619

  9. Effect of High Water Fluoride Concentration on the Intellectual Development of Children in Makoo/Iran

    OpenAIRE

    Shadfar, M.; B Seraj; M Shahrabi; Ahmadi, R.; M Fallahzadeh; H. Farrokh Eslamlu; M. J. Kharazifard

    2012-01-01

    Objective: Prolonged excessive intake of fluoride during child’s growth and development stages has been associated with mental and physical problems. The aim of this study was to investigate the effect of excessive fluoride intake on the intelligence quotient (IQ) of children living in five rural areas in Makoo/Iran. Materials and Methods: In this cross-sectional study, 293 children aged 6–11 years were selected from five villages in Makoo with normal fluoride (0.8±0.3 ppm), medium fluoride (...

  10. Health effects of indoor fluoride pollution from coal burning in China

    Energy Technology Data Exchange (ETDEWEB)

    Ando, M.; Tadano, M.; Asanuma, S.; Tamura, K.; Matsushima, S.; Watanabe, T.; Kondo, T.; Sakurai, S.; Ji, R.D.; Liang, C.K.; Cao, S.R. [National Institute of Environmental Studies, Osaka (Japan). Division of Regional Environment

    1998-05-01

    The combustion of high fluoride-content coal as an energy resource for heating, cooking, and food drying is a major exhaust emission source of suspended particulate matter and fluoride. High concentrations of these pollutants have been observed in indoor air of coal-burning families in some rural areas in China. Because airborne fluoride has serious toxicological properties, fluoride pollution in indoor air and the prevalence of fluorosis have been analyzed in a fluorosis area and a healthy nonfluorosis area in China and in a rural area in Japan. In the fluorosis area in China, concentrations of urinary fluoride in the residents were much higher than in the nonfluorosis area in China and in the rural area in Japan. In the fluorosis area, almost all elementary and junior high school students 10-15 years of age had dental fluorosis. Osteosclerosis in the skeletal fluorosis patients was serious. Urinary deoxypyridinoline in rural residents in China was much higher than in rural residents in Japan. Data suggest that fluoride may stimulate both bone resorption and bone formation. Because indoor fluoride from combustion of coal is easily absorbed in stored food and because food consumption is a main source of fluoride exposure, it is necessary to reduce airborne fluoride and food contamination to prevent serious fluorosis in China.

  11. Determination of fluoride source in ground water using petrographic studies in Dashtestan area, south of Iran

    Science.gov (United States)

    Battaleb-Looie, Sedigheh; Moore, Farid, ,, Dr.

    2010-05-01

    The groundwater occurs in Dashtestan area, contains a high level of fluoride. Since groundwater is vastly used for drinking and irrigation purposes, the local residents are at high risk of fluoride toxicity, as already evidenced by the occurrence of dental Fluorosis in many residents. 35 surface and groundwater samples were collected in September, 2009. The results show that in 23 samples the fluoride concentration is above the permissible level (1.5ppm). Petrographic study of lithological units in the catchment area indicates that mica minerals are the most probable source of fluoride content in the study area.

  12. Fluoride level in drinking water resources of gorgan rural regions, 1385

    Directory of Open Access Journals (Sweden)

    H Rahimzadeh

    2007-01-01

    Full Text Available Background and Objectives: Fluoride is one of the anions existed in water and soil. Its amount is not the same in different kind of water. Since the most of body's need to fluoride should be provided by drinking water, this study was aimed at determining the fluoride level in water supply of Gorgan rural regions. Materials and Methods: In this Cross-Sectional study, the subjects were all 67 water sources of the region. Every season, a one litter Sample was taken in a plastic Container and tested by SPADS Method. After Collecting and encoding the data, ANOVA was used to analyze. Results: The Findings shows that there are 4 springs and 63 wells which are Located in the mountainous (N=16 and flat (N= 47 regions. In every season, the average fluoride Level was lower than Standard Level (1.5 mg/L. The difference between fluoride Level of wells (0.39±0.15mg/L and springs (0.16± 0.13mg/L is Significant (p<0.05 the fluoride Level of mountainous wells is higher than wells located in flat regions (0.13mg/L. This deference was Significant (p<0.05. Conclusion: Based on The results revealing the fluoride Level of drinking water in Gorgan Rural region is less than international Standard, we recommend adding of Supplementary fluoride in foodstuffs of The people Living in This region. Key words: fluoride, drinking water resources, Gorgan, spring

  13. Fluoride release and uptake from glass ionomer cements and composite resins.

    Science.gov (United States)

    Weidlich, P; Miranda, L A; Maltz, M; Samuel, S M

    2000-01-01

    The aim of this investigation was to evaluate fluoride release and uptake from 4 glass ionomer cements (GICs)--Vitremer (VIT), Fuji II LC (FII LC), Fuji IX (FIX), Chelon Fill (CHE)--and 2 composite resins (CRs)--Heliomolar (H) and Zeta-100 (Z-100). Eight discs (8 mm x 2 mm) were made of each material and were stored in plastic vials containing artificial saliva at 37 degrees C. In group 1 (N = 3), the specimens were immersed in artificial saliva which was changed daily for 25 days. In group 2 (N = 5), besides receiving the same treatment as group 1, the specimens were immersed, after 24 hours, in a fluoride solution (1% NaF) for 1 min before daily saliva change. An ion-specific electrode (9609 BN-Orion) connected to an ion analyzer (SA-720 Procyon) was used to determine the amount of fluoride released at days 1, 2, 5, 10, 15, 20 and 25. Data were analyzed using two way ANOVA and Friedman's test. GICs released more fluoride during the first day and after this period the mean fluoride released decreased. Composite resin H released fluoride during the first day only and Z-100 did not release fluoride. In terms of NaF treatment, CRs did not show fluoride uptake, whereas the GICs showed fluoride uptake (VIT = FII LC = CHE > FIX). PMID:11210268

  14. Determination of Fluoride and Some Metal Ion Levels in the Drinking Waters in Kayseri Province

    OpenAIRE

    TOKALIOĞLU, Şerife; ŞAHİN, Uğur; Kartal, Şenol

    2001-01-01

    Fluorine is one of the most common elements in the Earth's crust. Fluoride is recognized to be the most effective caries-preventive agent. The main sources of fluoride for people are generally food and drinking water. For this reason, the fluoride and also the metal ion (Ca, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb and Zn) concentrations in the drinking waters collected from the city center of Kayseri and its counties were investigated. In the determination of fluoride and of Na and ...

  15. Thermodynamics of the conversion of calcium and magnesium fluorides to the parent metal oxides and hydrogen fluoride

    Energy Technology Data Exchange (ETDEWEB)

    West, M.H.; Axler, K.M.

    1997-02-01

    The authors have used thermodynamic modeling to examine the reaction of calcium fluoride (CaF{sub 2}) and magnesium fluoride (MgF{sub 2}) with water (H{sub 2}O) at elevated temperatures. The calculated, equilibrium composition corresponds to the global free-energy minimum for the system. Optimum, predicted reaction temperatures and reactant mole ratios are reported for the recovery of hydrogen fluoride (HF), a valuable industrial feedstock. Complete conversion of MgF{sub 2} is found at 1,000 C and a ratio of 40 moles of H{sub 2}O per 1 mole of MgF{sub 2}. For CaF{sub 2}, temperatures as high as 1,400 C are required for complete conversion at a corresponding mole ratio of 40 moles of H{sub 2}O per 1 mole of CaF{sub 2}. The authors discuss the presence of minor chemical constituents as well as the stability of various potential container materials for the pyrohydrolysis reactions at elevated temperatures. CaF{sub 2} and MgF{sub 2} slags are available as wastes at former uranium production facilities within the Department of Energy Complex and other facilities regulated by the Nuclear Regulatory Commission. Recovery of HF from these wastes is an example of environmental remediation at such facilities.

  16. Screening biological traits and fluoride contents of native vegetations in arid environments to select efficiently fluoride-tolerant native plant species for in-situ phytoremediation.

    Science.gov (United States)

    Boukhris, Asma; Laffont-Schwob, Isabelle; Mezghani, Imed; El Kadri, Lefi; Prudent, Pascale; Pricop, Anca; Tatoni, Thierry; Chaieb, Mohamed

    2015-01-01

    High fluoride pollution has been detected in the surrounding soils of the coastal superphosphate industries in the Gulf of Gabes (Southeast of Tunisia). A study was conducted in vicinity of factories analysing plant functional traits combined with plant fluoride accumulation and soil metal concentrations aiming to screen more efficiently native plant species tolerant to this pollution. Aerial parts of 18 plant species out of the 10 most abundant species per site were harvested on two polluted sites of Gabes and Skhira at the vicinity of the factories and on the less polluted site of Smara. Native plant species accumulated fluoride following the gradient of soil pollution. Fluoride contents of plant aerial parts ranged from 37 mg kg(-1) to 360 mg kg(-1) and five plant species were only found in the most polluted site. However these latter had low biomass and soil cover. Crossing biological traits and fluoride contents, a selection grid for potentially restorative plant species enabled the selection of three native perennials i.e. Rhanterium suaveolens, Atractylis serratuloides and, Erodium glaucophyllum as potential candidates for an in-situ phytoremediation program on arid fluoride-polluted sites. This approach may be used in other fluoride-polluted Mediterranean environments.

  17. Screening biological traits and fluoride contents of native vegetations in arid environments to select efficiently fluoride-tolerant native plant species for in-situ phytoremediation.

    Science.gov (United States)

    Boukhris, Asma; Laffont-Schwob, Isabelle; Mezghani, Imed; El Kadri, Lefi; Prudent, Pascale; Pricop, Anca; Tatoni, Thierry; Chaieb, Mohamed

    2015-01-01

    High fluoride pollution has been detected in the surrounding soils of the coastal superphosphate industries in the Gulf of Gabes (Southeast of Tunisia). A study was conducted in vicinity of factories analysing plant functional traits combined with plant fluoride accumulation and soil metal concentrations aiming to screen more efficiently native plant species tolerant to this pollution. Aerial parts of 18 plant species out of the 10 most abundant species per site were harvested on two polluted sites of Gabes and Skhira at the vicinity of the factories and on the less polluted site of Smara. Native plant species accumulated fluoride following the gradient of soil pollution. Fluoride contents of plant aerial parts ranged from 37 mg kg(-1) to 360 mg kg(-1) and five plant species were only found in the most polluted site. However these latter had low biomass and soil cover. Crossing biological traits and fluoride contents, a selection grid for potentially restorative plant species enabled the selection of three native perennials i.e. Rhanterium suaveolens, Atractylis serratuloides and, Erodium glaucophyllum as potential candidates for an in-situ phytoremediation program on arid fluoride-polluted sites. This approach may be used in other fluoride-polluted Mediterranean environments. PMID:25014764

  18. [Micro-determination of fluoride in biological samples by pyrohydrolysis and flow-injection analysis using a fluoride ion-selective electrode].

    Science.gov (United States)

    Itai, K

    1991-02-01

    An apparatus has been developed for the isolation of fluoride in biological samples through pyrohydrolysis. With this apparatus, it is possible to determine both organic and inorganic fluorocompounds with a recovery close to 100% and precision within 5%. The high recovery rate can be expected even for highly heat-resistant compounds such as CaF2, without using WO3 as a catalyst. For determination of the isolated fluoride, a separate apparatus was developed in which flow-injection analysis was used in conjunction with a fluoride ion-selective electrode as a detector. With this apparatus, fluoride in a sample solution with a volume as small as 0.2 ml, and at a concentration as low as 0.5 microgram/l, can be determined within 3 minutes with a precision of several percent. Combined use of the two apparatuses makes it possible to determine fluoride in different biological samples within 10-15 minutes with a precision of several percent, free from external contamination. By selecting suitable conditions for analysis and using a 1 g sample, it is possible to determine fluoride at a concentration as low as 5 ng/g. By employing these apparatuses, the fluoride content in different biological samples has been determine and the effectiveness of their use confirmed. PMID:2051632

  19. Sensitivity of two biomarkers for biomonitoring exposure to fluoride in children and women: A study in a volcanic area.

    Science.gov (United States)

    Linhares, Diana Paula Silva; Garcia, Patrícia Ventura; Amaral, Leslie; Ferreira, Teresa; Cury, Jaime A; Vieira, Waldomiro; Rodrigues, Armindo Dos Santos

    2016-07-01

    The natural enrichment of water with fluoride is related to natural sources such as volcanic activity, with it being documented that fluorosis, an endemic and widespread disease in volcanic areas, is associated to the ingestion of high levels of fluoride through water. Thus, in this study, we aimed to define the fluoride concentration in drinking waters of volcanic origin and compare the sensitivity of urine and nail clippings as biomarkers for fluoride exposure in adults and children. Samples of drinking water from four villages in São Miguel Island (Azores) were used and the fluoride concentration was determined, as well the fluoride content in urine and toenails clippings from 66 children and 63 adults from these villages. A validated diet questionnaire, assessing sources of fluoride, was recorded for each participant. The fluoride determination in urine and nail clipping samples was made using a fluoride-specific electrode. A positive correlation was found between the fluoride daily intake and fluoride content in children urine (rs = 0.475; p < 0.001) and in their nail clippings (rs = 0.475; p < 0.001), while in adult women, the fluoride daily intake correlated positively with fluoride content nail clippings (rs = 0.495, p < 0.001). This reveals that nail clippings are more reliable as biomarkers of chronic exposure to fluoride than urine for populations of different ages (children vs. adults). Furthermore, nail clippings are more suitable than urine fluoride levels to assess long term exposure to fluoride in areas where the exposure to fluoride in drinking water is considered within, or slightly above, the recommended legal values.

  20. Comparative study of fluoride released and recharged from conventional pit and fissure sealants versus surface prereacted glass ionomer technology

    Directory of Open Access Journals (Sweden)

    Elias Nahum Salmerón-Valdés

    2016-01-01

    Full Text Available Context: The fluoride release of sealants in vitro shows a marked decrease. Giomers are distinguishable from manufactured resin-based sealants and contain prereacted glass-ionomer particles (PRG. Aims: To compare the amounts of fluoride released from the main pit and fissure of a resin-based sealant with that from a Giomer and to assess the abilities of the sealant and the Giomer to recharge when exposed to regular use of fluoride rinse. Materials and Methods: The readings for the fluoride concentration were carried out for 60 days using a fluoride ion-specific electrode. After this period, the samples were recharged using a fluoride mouth rinse. The amount of fluoride released after this recharge was determined for 5 days. The data were analyzed using Student′s t- and analysis of variance tests. Results: In general, all materials presented higher fluoride release in the first 24 h; G1 and G4 showed a higher fluoride release in this period. On the other hand, G3 and G1 presented the most constant fluoride release until the 8 th day, wherein all the sealants considerably decreased in the amount of fluoride released. Conclusion: G1 and G3 released higher concentrations of fluoride, although no significant differences were found. Giomers recharged in the first 24 h after polymerization presented an improved and sustained fluoride release.