WorldWideScience

Sample records for carbon composite material

  1. Carbon nanotube composite materials

    Energy Technology Data Exchange (ETDEWEB)

    O' Bryan, Gregory; Skinner, Jack L; Vance, Andrew; Yang, Elaine Lai; Zifer, Thomas

    2015-03-24

    A material consisting essentially of a vinyl thermoplastic polymer, un-functionalized carbon nanotubes and hydroxylated carbon nanotubes dissolved in a solvent. Un-functionalized carbon nanotube concentrations up to 30 wt % and hydroxylated carbon nanotube concentrations up to 40 wt % can be used with even small concentrations of each (less than 2 wt %) useful in producing enhanced conductivity properties of formed thin films.

  2. Carbon Nanotube Composites: Strongest Engineering Material Ever?

    Science.gov (United States)

    Mayeaux, Brian; Nikolaev, Pavel; Proft, William; Nicholson, Leonard S. (Technical Monitor)

    1999-01-01

    The primary goal of the carbon nanotube project at Johnson Space Center (JSC) is to fabricate structural materials with a much higher strength-to-weight ratio than any engineered material today, Single-wall nanotubes present extraordinary mechanical properties along with new challenges for materials processing. Our project includes nanotube production, characterization, purification, and incorporation into applications studies. Now is the time to move from studying individual nanotubes to applications work. Current research at JSC focuses on structural polymeric materials to attempt to lower the weight of spacecraft necessary for interplanetary missions. These nanoscale fibers present unique new challenges to composites engineers. Preliminary studies show good nanotube dispersion and wetting by the epoxy materials. Results of tensile strength tests will also be reported. Other applications of nanotubes are also of interest for energy storage, gas storage, nanoelectronics, field emission, and biomedical uses.

  3. Carbon Cryogel Silicon Composite Anode Materials for Lithium Ion Batteries

    Science.gov (United States)

    Woodworth James; Baldwin, Richard; Bennett, William

    2010-01-01

    A variety of materials are under investigation for use as anode materials in lithium-ion batteries, of which, the most promising are those containing silicon. 10 One such material is a composite formed via the dispersion of silicon in a resorcinol-formaldehyde (RF) gel followed by pyrolysis. Two silicon-carbon composite materials, carbon microspheres and nanofoams produced from nano-phase silicon impregnated RF gel precursors have been synthesized and investigated. Carbon microspheres are produced by forming the silicon-containing RF gel into microspheres whereas carbon nano-foams are produced by impregnating carbon fiber paper with the silicon containing RF gel to create a free standing electrode. 1-4,9 Both materials have demonstrated their ability to function as anodes and utilize the silicon present in the material. Stable reversible capacities above 400 mAh/g for the bulk material and above 1000 mAh/g of Si have been observed.

  4. Improved Composites Using Crosslinked, Surface-Modified Carbon Nanotube Materials

    Science.gov (United States)

    Baker, James Stewart

    2014-01-01

    Individual carbon nanotubes (CNTs) exhibit exceptional tensile strength and stiffness; however, these properties have not translated well to the macroscopic scale. Premature failure of bulk CNT materials under tensile loading occurs due to the relatively weak frictional forces between adjacent CNTs, leading to poor load transfer through the material. When used in polymer matrix composites (PMCs), the weak nanotube-matrix interaction leads to the CNTs providing less than optimal reinforcement.Our group is examining the use of covalent crosslinking and surface modification as a means to improve the tensile properties of PMCs containing carbon nanotubes. Sheet material comprised of unaligned multi-walled carbon nanotubes (MWCNT) was used as a drop-in replacement for carbon fiber in the composites. A variety of post-processing methods have been examined for covalently crosslinking the CNTs to overcome the weak inter-nanotube shear interactions, resulting in improved tensile strength and modulus for the bulk sheet material. Residual functional groups from the crosslinking chemistry may have the added benefit of improving the nanotube-matrix interaction. Composites prepared using these crosslinked, surface-modified nanotube sheet materials exhibit superior tensile properties to composites using the as received CNT sheet material.

  5. Multilayer Electroactive Polymer Composite Material Comprising Carbon Nanotubes

    Science.gov (United States)

    Ounaies, Zoubeida (Inventor); Park, Cheol (Inventor); Harrison, Joycelyn S. (Inventor); Holloway, Nancy M. (Inventor); Draughon, Gregory K. (Inventor)

    2009-01-01

    An electroactive material comprises multiple layers of electroactive composite with each layer having unique dielectric, electrical and mechanical properties that define an electromechanical operation thereof when affected by an external stimulus. For example, each layer can be (i) a 2-phase composite made from a polymer with polarizable moieties and an effective amount of carbon nanotubes incorporated in the polymer for a predetermined electromechanical operation, or (ii) a 3-phase composite having the elements of the 2-phase composite and further including a third component of micro-sized to nano-sized particles of an electroactive ceramic incorporated in the polymer matrix.

  6. Hybrid Aluminum Composite Materials Based on Carbon Nanostructures

    Directory of Open Access Journals (Sweden)

    Tatiana S. Koltsova

    2015-09-01

    Full Text Available We investigated formation of carbon nanofibers grown by chemical deposition (CVD method using an acetylene-hydrogen mixture on the surface of micron-sized aluminum powder particles. To obtain uniform distribution of the carbon nanostructures on the particles we deposited nickel catalyst on the surface by spraying from the aqueous solution of nickel nitrate. It was found that increasing the time of the synthesis lowers the rate of growth of carbon nanostructures due to the deactivation of the catalyst. The Raman spectroscopy measurements confirm the presence of disordered carbon corresponding to CNFs in the specimen. X-ray photoelectron spectroscopy showed the presence of aluminum carbide in the hot pressed samples. An aluminum composite material prepared using 1 wt.% CNFs obtained by uniaxial cold pressing and sintering showed 30% increase in the hardness compared to pure aluminum, whereas the composites prepared by hot pressing showed 80% increase in the hardness. Composite materials have satisfactory ductility. Thus, the aluminum based material reinforced with carbon nanostructures should be appropriate for creating high-strength and light compacts for aerospace and automotive applications and power engineering.DOI: http://dx.doi.org/10.5755/j01.ms.21.3.7355

  7. Damage-tolerant composite materials produced by stitching carbon fibers

    Science.gov (United States)

    Dow, Marvin B.; Smith, Donald L.

    1989-01-01

    NASA-Langley has undertaken the investigation of composite damage-tolerance enhancement and fabrication economies-maximization via reinforcement-stitching, in combination with resin transfer molding. Attention is given to results obtained by an experimental evaluation of composites tailored for damage tolerance by stitching layers of dry carbon-fiber fabric with closely-spaced threads, in order to furnish through-the-thickness reinforcement. Various stitching patterns and thread materials have been evaluated, using flat-plate specimens; blade-stiffened structural elements have been fabricated and tested. The results presented indicate that stitched laminates furnish damage tolerance performance comparable to that of more expensive, toughened-matrix composites.

  8. Carbon Cryogel and Carbon Paper-Based Silicon Composite Anode Materials for Lithium-Ion Batteries

    Science.gov (United States)

    Woodworth, James; Baldwin, Richard; Bennett, William

    2010-01-01

    A variety of materials are under investigation for use as anode materials in lithium-ion batteries, of which, the most promising are those containing silicon. 6 One such material is a composite formed via the dispersion of silicon in a resorcinol-formaldehyde (RF) gel followed by pyrolysis. Two silicon-carbon composite materials, carbon microspheres and nanofoams produced from nano-phase silicon impregnated RF gel precursors have been synthesized and investigated. Carbon microspheres are produced by forming the silicon-containing RF gel into microspheres whereas carbon nano-foams are produced by impregnating carbon fiber paper with the silicon containing RF gel to create a free standing electrode. 1-5 Both materials have demonstrated their ability to function as anodes and utilize the silicon present in the material. Stable reversible capacities above 400 mAh/g for the bulk material and above 1000 mAh/g of Si have been observed.

  9. Silicon Composite Anode Materials for Lithium Ion Batteries Based on Carbon Cryogels and Carbon Paper

    Science.gov (United States)

    Woodworth, James; Baldwin, Richard; Bennett, William

    2010-01-01

    A variety of materials are under investigation for use as anode materials in lithium-ion batteries, of which, the most promising are those containing silicon. One such material is a composite formed via the dispersion of silicon in a resorcinol-formaldehyde (RF) gel followed by pyrolysis. Two silicon-carbon composite materials, carbon microspheres and nanofoams produced from nano-phase silicon impregnated RF gel precursors have been synthesized and investigated. Carbon microspheres are produced by forming the silicon-containing RF gel into microspheres whereas carbon nanofoams are produced by impregnating carbon fiber paper with the silicon containing RF gel to create a free standing electrode. Both materials have demonstrated their ability to function as anodes and utilize the silicon present in the material. Stable reversible capacities above 400 mAh/g for the bulk material and above 1000 mAh/g of Si have been observed.

  10. Composite Materials with Magnetically Aligned Carbon Nanoparticles Having Enhanced Electrical Properties and Methods of Preparation

    Science.gov (United States)

    Hong, Haiping (Inventor); Peterson, G.P. (Bud) (Inventor); Salem, David R. (Inventor)

    2016-01-01

    Magnetically aligned carbon nanoparticle composites have enhanced electrical properties. The composites comprise carbon nanoparticles, a host material, magnetically sensitive nanoparticles and a surfactant. In addition to enhanced electrical properties, the composites can have enhanced mechanical and thermal properties.

  11. Carbon Materials Metal/Metal Oxide Nanoparticle Composite and Battery Anode Composed of the Same

    Science.gov (United States)

    Hung, Ching-Cheh (Inventor)

    2006-01-01

    A method of forming a composite material for use as an anode for a lithium-ion battery is disclosed. The steps include selecting a carbon material as a constituent part of the composite, chemically treating the selected carbon material to receive nanoparticles, incorporating nanoparticles into the chemically treated carbon material and removing surface nanoparticles from an outside surface of the carbon material with incorporated nanoparticles. A material making up the nanoparticles alloys with lithium.

  12. Electromagnetic properties of carbon black and barium titanate composite materials

    Energy Technology Data Exchange (ETDEWEB)

    Wang Guiqin [School of Material Science and Engineering, Dalian University of Technology, Dalian 116023 (China)], E-mail: c2b2chen@163.com; Chen Xiaodong; Duan Yuping; Liu Shunhua [School of Material Science and Engineering, Dalian University of Technology, Dalian 116023 (China)

    2008-04-24

    Nanocrystalline carbon black/barium titanate compound particle (CP) was synthesized by sol-gel method. The phase structure and morphology of compound particle were investigated by X-ray diffraction (XRD), transmission electron microscope (TEM) and Raman spectrum measurements, the electroconductivity was test by trielectrode arrangement and the precursor powder was followed by differential scanning calorimetric measurements (DSC) and thermal gravimetric analysis (TGA). In addition, the complex relative permittivity and permeability of compound particle were investigated by reflection method. The compound particle/epoxide resin composite (CP/EP) with different contents of CP were measured. The results show barium titanate crystal is tetragonal phase and its grain is oval shape with 80-100 nm which was coated by carbon black film. As electromagnetic (EM) complex permittivity, permeability and reflection loss (RL) shown that the compound particle is mainly a kind of electric and dielectric lossy materials and exhibits excellent microwave absorption performance in the X- and Ku-bands.

  13. 21 CFR 878.3500 - Polytetrafluoroethylene with carbon fibers composite implant material.

    Science.gov (United States)

    2010-04-01

    ... composite implant material. 878.3500 Section 878.3500 Food and Drugs FOOD AND DRUG ADMINISTRATION... Prosthetic Devices § 878.3500 Polytetrafluoroethylene with carbon fibers composite implant material. (a) Identification. A polytetrafluoroethylene with carbon fibers composite implant material is a porous...

  14. Nanoengineered thermal materials based on carbon nanotube array composites

    Science.gov (United States)

    Li, Jun (Inventor); Meyyappan, Meyya (Inventor); Dangelo, Carlos (Inventor)

    2010-01-01

    A method for providing for thermal conduction using an array of carbon nanotubes (CNTs). An array of vertically oriented CNTs is grown on a substrate having high thermal conductivity, and interstitial regions between adjacent CNTs in the array are partly or wholly filled with a filler material having a high thermal conductivity so that at least one end of each CNT is exposed. The exposed end of each CNT is pressed against a surface of an object from which heat is to be removed. The CNT-filler composite adjacent to the substrate provides improved mechanical strength to anchor CNTs in place and also serves as a heat spreader to improve diffusion of heat flux from the smaller volume (CNTs) to a larger heat sink.

  15. Carbon-Carbon Composites as Recuperator Material for Direct Gas Brayton Systems

    Energy Technology Data Exchange (ETDEWEB)

    RA Wolf

    2006-07-19

    Of the numerous energy conversion options available for a space nuclear power plant (SNPP), one that shows promise in attaining reliable operation and high efficiency is the direct gas Brayton (GB) system. In order to increase efficiency, the GB system incorporates a recuperator that accounts for nearly half the weight of the energy conversion system (ECS). Therefore, development of a recuperator that is lighter and provides better performance than current heat exchangers could prove to be advantageous. The feasibility of a carbon-carbon (C/C) composite recuperator core has been assessed and a mass savings of 60% and volume penalty of 20% were projected. The excellent thermal properties, high-temperature capabilities, and low density of carbon-carbon materials make them attractive in the GB system, but development issues such as material compatibility with other structural materials in the system, such as refractory metals and superalloys, permeability, corrosion, joining, and fabrication must be addressed.

  16. Carbon Carbon Composites: An Overview .

    Directory of Open Access Journals (Sweden)

    G. Rohini Devi

    1993-10-01

    Full Text Available Carbon carbon composites are a new class of engineering materials that are ceramic in nature but exhibit brittle to pseudoplastic behaviour. Carbon-carbon is a unique all-carbon composite with carbon fibre embeded in carbon matrix and is known as an inverse composite. Due to their excellent thermo-structural properties, carbon-carbon composites are used in specialised application like re-entry nose-tips, leading edges, rocket nozzles, and aircraft brake discs apart from several industrial and biomedical applications. The multidirectional carbon-carbon product technology is versatile and offers design flexibility. This paper describes the multidirectional preform and carbon-carbon process technology and research and development activities within the country. Carbon-carbon product experience at DRDL has also been discussed. Development of carbon-carbon brake discs process technology using the liquid impregnation process is described. Further the test results on material characterisation, thermal, mechanical and tribological properties are presented.

  17. Nanoengineered Thermal Materials Based on Carbon Nanotube Array Composites

    Science.gov (United States)

    Li, Jun; Meyyappan, Meyya; Dangelo, Carols

    2012-01-01

    State-of-the-art integrated circuits (ICs) for microprocessors routinely dissipate power densities on the order of 50 W/cm2. This large power is due to the localized heating of ICs operating at high frequencies and must be managed for future high-frequency microelectronic applications. As the size of components and devices for ICs and other appliances becomes smaller, it becomes more difficult to provide heat dissipation and transport for such components and devices. A thermal conductor for a macro-sized thermal conductor is generally inadequate for use with a microsized component or device, in part due to scaling problems. A method has been developed for providing for thermal conduction using an array of carbon nanotubes (CNTs). An array of vertically oriented CNTs is grown on a substrate having high thermal conductivity, and interstitial regions between adjacent CNTs in the array are partly or wholly filled with a filler material having a high thermal conductivity so that at least one end of each CNT is exposed. The exposed end of each CNT is pressed against a surface of an object from which heat is to be removed. The CNT-filler-composite adjacent to the substrate provides improved mechanical strength to anchor CNTs in place, and also serves as a heat spreader to improve diffusion of heat flux from the smaller volume (CNTs) to a larger heat sink.

  18. Elastomer-Carbon Nanostructure Composites as Prospective Materials for Flexible Robotic Tactile Sensors

    OpenAIRE

    Knite, M; Podiņš, G; Zīke, S; Zavickis, J

    2008-01-01

    Our recent achievements in the design, processing and studies of physical properties of elastomer – nano-structured carbon composites as prospective compressive strain sensor materials for robotic tactile elements are presented. Composites made of polyisoprene matrix and high-structured carbon black or multi-wall carbon nano-tube filler have been designed and manufactured to develop completely flexible conductive polymer nano-composites for tactile sensing elements. Electrical resistance of t...

  19. Comparative Investigation of the Efficiency of Absorption of Solar Energy by Carbon Composite Materials

    Science.gov (United States)

    Prikhod‧ko, N. G.; Smagulova, G. T.; Rakhymzhan, N. B.; Kim, S.; Lesbaev, B. T.; Nazhipkyzy, M.; Mansurov, Z. A.

    2017-01-01

    This paper presents the results of research on the efficiency of absorption of solar energy by various carbon materials (soot, carbonized apricot pits and rice husks, and carbon nanotubes in the form of a ″forest″), as well as by composites based on them with inclusions of metal oxide nanoparticles. An analysis of the efficiency of absorption of solar energy by various carbon materials has demonstrated the advantage of the carbon material from carbonized apricot pits. The results of the comparative investigation of the absorptivity of apricot pits with that of the coating of a production prototype of solar collector are presented.

  20. Carbon Nanotube Enhanced Aerospace Composite Materials A New Generation of Multifunctional Hybrid Structural Composites

    CERN Document Server

    Kostopoulos, V

    2013-01-01

    The well documented increase in the use of high performance composites as structural materials in aerospace components is continuously raising the demands in terms of dynamic performance, structural integrity, reliable life monitoring systems and adaptive actuating abilities. Current technologies address the above issues separately; material property tailoring and custom design practices aim to the enhancement of dynamic and damage tolerance characteristics, whereas life monitoring and actuation is performed with embedded sensors that may be detrimental to the structural integrity of the component. This publication explores the unique properties of carbon nanotubes (CNT) as an additive in the matrix of Fibre Reinforced Plastics (FRP), for producing structural composites with improved mechanical performance as well as sensing/actuating capabilities. The successful combination of the CNT properties and existing sensing actuating technologies leads to the realization of a multifunctional FRP structure. The curre...

  1. Adsorption capacity of hydrophobic SiO2 aerogel/activated carbon composite materials for TNT

    Institute of Scientific and Technical Information of China (English)

    ZHOU; XiaoFang; CUI; Sheng; LIU; Yu; LIU; XueYong; SHEN; XiaoDong; WU; ZhanWu

    2013-01-01

    The adsorption properties of TNT from wastewater by hydrophobic silica aerogel/activated carbon composite materials were investigated. The effects of adsorption time, pH value, adsorption temperature, and the amount of the composite materials on the adsorption rate were studied. The adsorption principle and mechanism of the composite materials were discussed along with the Freundlich equation. The results showed that the best adsorption rate of the hydrophobic silica aerogel/activated car-bon composite materials could reach 96.5% with adsorption conditions of adsorption temperature 25°C, pH value 7, the amount of SiO2aerogel dosage 3.33 g/L, and adsorption time of 120 min. The adsorption of hydrophobic SiO2aero-gel/activated carbon composite materials for TNT solution is mainly surface adsorption, and also has some chemical adsorp-tion when the aerogel hydrophobicity is modified.

  2. Conditions for forming composite carbon nanotube-diamond like carbon material that retain the good properties of both materials

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Wei, E-mail: wei.ren@helsinki.fi; Avchaciov, Konstantin; Nordlund, Kai [Department of Physics, University of Helsinki, P.O. Box 43, FIN-00014 Helsinki (Finland); Iyer, Ajai; Koskinen, Jari [Department of Materials Science and Engineering, School of Chemical Technology, Aalto University, P.O. Box 16200, 00076 Espoo (Finland); Kaskela, Antti; Kauppinen, Esko I. [NanoMaterials Group, Department of Applied Physics, Aalto University School of Science, P.O. Box 15100, 00076 Aalto (Finland)

    2015-11-21

    Carbon nanotubes are of wide interest due to their excellent properties such as tensile strength and electrical and thermal conductivity, but are not, when placed alone on a substrate, well resistant to mechanical wear. Diamond-like carbon (DLC), on the other hand, is widely used in applications due to its very good wear resistance. Combining the two materials could provide a very durable pure carbon nanomaterial enabling to benefit from the best properties of both carbon allotropes. However, the synthesis of high-quality diamond-like carbon uses energetic plasmas, which can damage the nanotubes. From previous works it is neither clear whether the quality of the tubes remains good after DLC deposition, nor whether the DLC above the tubes retains the high sp{sup 3} bonding fraction. In this work, we use experiments and classical molecular dynamics simulations to study the mechanisms of DLC formation on various carbon nanotube compositions. The results show that high-sp{sup 3}-content DLC can be formed provided the deposition conditions allow for sidewards pressure to form from a substrate close beneath the tubes. Under optimal DLC formation energies of around 40–70 eV, the top two nanotube atom layers are fully destroyed by the plasma deposition, but layers below this can retain their structural integrity.

  3. Conditions for forming composite carbon nanotube-diamond like carbon material that retain the good properties of both materials

    Science.gov (United States)

    Ren, Wei; Iyer, Ajai; Koskinen, Jari; Kaskela, Antti; Kauppinen, Esko I.; Avchaciov, Konstantin; Nordlund, Kai

    2015-11-01

    Carbon nanotubes are of wide interest due to their excellent properties such as tensile strength and electrical and thermal conductivity, but are not, when placed alone on a substrate, well resistant to mechanical wear. Diamond-like carbon (DLC), on the other hand, is widely used in applications due to its very good wear resistance. Combining the two materials could provide a very durable pure carbon nanomaterial enabling to benefit from the best properties of both carbon allotropes. However, the synthesis of high-quality diamond-like carbon uses energetic plasmas, which can damage the nanotubes. From previous works it is neither clear whether the quality of the tubes remains good after DLC deposition, nor whether the DLC above the tubes retains the high sp3 bonding fraction. In this work, we use experiments and classical molecular dynamics simulations to study the mechanisms of DLC formation on various carbon nanotube compositions. The results show that high-sp3-content DLC can be formed provided the deposition conditions allow for sidewards pressure to form from a substrate close beneath the tubes. Under optimal DLC formation energies of around 40-70 eV, the top two nanotube atom layers are fully destroyed by the plasma deposition, but layers below this can retain their structural integrity.

  4. Structural Characterization and Property Study on the Activated Alumina-activated Carbon Composite Material

    Institute of Scientific and Technical Information of China (English)

    CHEN Yan-Qing; WU Ren-Ping; YE Xian-Feng

    2012-01-01

    AlCl3,NH3·H2O,HNO3 and activated carbon were used as raw materials to prepare one new type of activated alumina-activated carbon composite material.The influence of heat treatment conditions on the structure and property of this material was discussed;The microstructures of the composite material were characterized by XRD,SEM,BET techniques;and its formaldehyde adsorption characteristic was also tested.The results showed that the optimal heat treatment temperature of the activated alumina-activated carbon composite material was 450 ℃,iodine adsorption value was 441.40 mg/g,compressive strength was 44 N,specific surface area was 360.07 m2/g,average pore size was 2.91 nm,and pore volume was 0.26 m3/g.According to the BET pore size distribution diagram,the composite material has dual-pore size distribution structure,the micro-pore distributes in the range of 0.6-1.7 nm,and the meso-pore in the range of 3.0-8.0 nm.The formaldehyde adsorption effect of the activated alumina-activated carbon composite material was excellent,much better than that of the pure activated carbon or activated alumina,and its saturated adsorption capacity was 284.19 mg/g.

  5. Preparation of mesoporous carbon/polypyrrole composite materials and their supercapacitive properties

    Directory of Open Access Journals (Sweden)

    WU-JUN ZOU

    2011-08-01

    Full Text Available We synthesized mesoporous carbons/polypyrrole composites, using a chemical oxidative polymerization and calcium carbonate as a sacrificial template. N2 adsorption-desorption method, Fourier infrared spectroscopy, and transmission electron microscopy were used to characterize the structure and morphology of the composites. The measurement results indicated that as-synthesized carbon with the disordered mesoporous structure and a pore size of approximately 5 nm was uniformly coated by polypyrrole. The electrochemical behavior of the resulting composite was examined by cyclic voltammetry and cycle life measurements, and the obtained results showed that the specific capacitance of the resulting composite electrode was as high as 313 F g−1, nearly twice the capacitance of pure mesoporous carbon electrode (163 F g–1. This reveals that the electrochemical performance of these materials is governed by a combination of the electric double layer capacitance of mesoporous carbon and pseudocapacitance of polypyrrole.

  6. Preparation and Properties of Paraffin/TiO2/Active-carbon Composite Phase Change Materials

    Directory of Open Access Journals (Sweden)

    HAO Yong-gan

    2016-11-01

    Full Text Available A novel composite phase change materials (PCMs of paraffin/TiO2/active-carbon was prepared by a microemulsion method, where paraffin acted as a PCM and titanium dioxide (TiO2 as matrix material, and a small amount of active carbon was added to improve the thermal conductivity. The compositions, morphology and thermal properties of the paraffin/TiO2/active-carbon composite PCMs were characterized by XRD, SEM, TGA and DSC respectively. The shape stability during phase change process of this composite was also tested. The results show that paraffin is well encapsulated by TiO2 matrix, and thus exhibiting excellent shape-stabilized phase change feature. Besides, this composite PCM also presents superhydrophobic property. Therefore, these multifunctional features will endow PCMs with important application potential in energy efficient buildings.

  7. Carbonization of wood at 400°C for composite materials

    Science.gov (United States)

    Randrianarisoa, Bernard Laurent

    The carbonization process for large pieces of wood was investigated to produce a solid carbonized wood skeleton precursor that retains the cellular structure of the wood without the formation of cracks and with reduced longitudinal deformation. Two carbonization schedules were designed for the conversion of sugar maple (Acer saccharum) and southern pine ( Pinus spp) into amorphous carbon at a heat treatment temperature of 400°C. Samples from commercial lumber were carbonized to produce the materials. Each schedule was designed meticulously through DTA-TGA for each wood species. The materials were characterized by their average yields, dimensional changes, density, porosity, SEM and mechanical testing. Also, the materials were used as solid carbon skeletons for making resin-infused carbon composites. Structural epoxy resin was infused into the carbon material template and cured at a maximum temperature of 125°C. The depth of the resin infusion was assessed by SEM examination and the retention was analyzed by total weight gain. The strength and the stiffness of the composite materials were evaluated through mechanical testing. It was demonstrated that southern pine and sugar maple should require different heat treatment schedules for carbonization. The schedules were able to reduce the longitudinal deformation and to keep the final products free of cracks. The yield averaged around 28% for both southern pine and sugar maple. Carbonized southern pine exhibited lower density and higher porosity than carbonized sugar maple. The resin treatment increased specific gravity of carbonized materials by 9.6% and 11.6% for maple and southern pine respectively. The resin infusion improved the average MOR values by 140% and 275%. MOE of the composites was similar to that of pure epoxy.

  8. Evaluation for cell affinity of the composite material containing carbon nanotubes

    Institute of Scientific and Technical Information of China (English)

    KANG Shizhao; WAN Yuqing; YAN Huijuan; BEI Jianzhong; WANG Chen; WANG Shenguo; WANG Chunru; WAN Lijun; BAI Chunli

    2004-01-01

    The composite material of poly-(L-lactide) (PLLA) and carbon nanotubes (CNTs) were prepared. Its surface morphologies and property were worked out by using atomic force microscopy (AFM) and contact angle measurement. Moreover, the prime cytocompatibility was used to investigate the biocompatibility of the composite material containing CNTs and the effects of CNTs on one aspect of cell function, cell affinity. The results obtained indicate that the composite material of PLLA and CNTs possesses good biocompatibility for both the 3T3 fibroblasts and Oct-1 osteoblast-like cells. The addition of CNTs will greatly affect cell affinity of the material, which may be disadvantage for the cell adhesion.

  9. Advanced carbon materials/olivine LiFePO4 composites cathode for lithium ion batteries

    Science.gov (United States)

    Gong, Chunli; Xue, Zhigang; Wen, Sheng; Ye, Yunsheng; Xie, Xiaolin

    2016-06-01

    In the past two decades, LiFePO4 has undoubtly become a competitive candidate for the cathode material of the next-generation LIBs due to its abundant resources, low toxicity and excellent thermal stability, etc. However, the poor electronic conductivity as well as low lithium ion diffusion rate are the two major drawbacks for the commercial applications of LiFePO4 especially in the power energy field. The introduction of highly graphitized advanced carbon materials, which also possess high electronic conductivity, superior specific surface area and excellent structural stability, into LiFePO4 offers a better way to resolve the issue of limited rate performance caused by the two obstacles when compared with traditional carbon materials. In this review, we focus on advanced carbon materials such as one-dimensional (1D) carbon (carbon nanotubes and carbon fibers), two-dimensional (2D) carbon (graphene, graphene oxide and reduced graphene oxide) and three-dimensional (3D) carbon (carbon nanotubes array and 3D graphene skeleton), modified LiFePO4 for high power lithium ion batteries. The preparation strategies, structure, and electrochemical performance of advanced carbon/LiFePO4 composite are summarized and discussed in detail. The problems encountered in its application and the future development of this composite are also discussed.

  10. Activated Carbon-Fly Ash-Nanometal Oxide Composite Materials: Preparation, Characterization, and Tributyltin Removal Efficiency

    Directory of Open Access Journals (Sweden)

    Olushola S. Ayanda

    2013-01-01

    Full Text Available The physicochemical properties, nature, and morphology of composite materials involving activated carbon, fly ash, nFe3O4, nSiO2, and nZnO were investigated and compared. Nature and morphology characterizations were carried out by means of scanning electron and transmission electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. Other physicochemical characterizations undertaken were CNH analysis, ash content, pH, point of zero charge, and surface area and porosity determination by BET. Experimental results obtained revealed that activated carbon, nSiO2, activated carbon-fly ash, activated carbon-fly ash-nFe3O4, activated carbon-fly ash-nSiO2, and activated carbon-fly ash-nZnO composite materials exhibited net negative charge on their surfaces while fly ash, nFe3O4, and nZnO possessed net positive charge on their surfaces. Relatively higher removal efficiency (>99% of TBT was obtained for all the composite materials compared to their respective precursors except for activated carbon. These composite materials therefore offer great potential for the remediation of TBT in wastewaters.

  11. Damage Mechanisms/Failure Mechanics of Carbon-Carbon Composite Materials.

    Science.gov (United States)

    1979-09-01

    cutting method was used to minimize material waste, not because * carbon-carbon is difficult to machine . 2.2 Tension Testing 2.2.1 Specimen Configuration...was made to bond the strain gages to fiber bundles if possible rather than to a layer of matrix material. Ex- tensometers were also employed to measure

  12. Friction Behaviour of Polymeric Composite Materials Mixed with Carbon Fibers Having Different Orientations Layout

    Science.gov (United States)

    Caliman, R.

    2016-06-01

    This paper presents a study of the friction properties of polymeric composite materials reinforced with unidirectional carbon fibers having different stratified structure. So, the composites are complex and versatile materials but their behaviour in practice is not fully studied. For instance, these polymeric composite materials mixed with carbon fibers after being investigated in terms of wear, did not elucidate the effect of fiber orientation on wear properties. Is therefore necessary to investigate the effect of carbon fibers orientation on the friction-wear properties of the reinforced composite materials tested to abrasive and adhesive friction. Research work has been done with unidirectional composite materials having overlap 18 successive layers made from a polymeric resine and 60% of carbon fibers. The stratified structure was obtained by compressing multiple pre-impregnated strips, positioned manually. During this experimental work, three types of test samples were investigated: parallel, normal and anti-parallel, taking in consideration the carbon fibre orientation with respect to the sliding direction. The friction coefficient is computed function to the friction load and loading value. Also, the specific wear rate was calculated according to: the mass loss, density, the normal contact surface, the sliding distance and load rating.

  13. Investigation of Thermostability of a Composite Resistive Material with Nanodimensional Carbon Fillers

    Science.gov (United States)

    Malinovskaya, T. D.; Vlasov, V. A.; Volokitin, G. G.; Melentyev, S. V.

    2014-06-01

    Thermostability of resistive materials based on polyurethane used as heat-liberating elements in the design of heating elements of thermoactive formworks is investigated. The application of polyurethane as a binder provides solid contact of polymer molecules with nanodimensional carbon fillers and their uniform distribution in a composite material. The influence of thermal treatment and dispersed fillers on the stability of electrophysical and thermophysical properties of carbon-filled polyurethane coatings is established.

  14. Properties of the chalcogenide–carbon nano tubes and graphene composite materials

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Abhay Kumar, E-mail: abhaysngh@rediffmail.com [Department of Physics, Indian Institute of Science, Bangalore 560012 (India); Department of Electronics Engineering, Incheon National University, Incheon 406-772 (Korea, Republic of); Department of Physics, Incheon National University, Incheon 406-772 (Korea, Republic of); Kim, JunHo [Department of Physics, Incheon National University, Incheon 406-772 (Korea, Republic of); Park, Jong Tae [Department of Electronics Engineering, Incheon National University, Incheon 406-772 (Korea, Republic of); Sangunni, K.S. [Department of Physics, Indian Institute of Science, Bangalore 560012 (India)

    2015-04-05

    Highlights: • Chalcogenides. • Melt quenched. • Composite materials. • Multi walled carbon nano tubes. • Bilayer graphene. - Abstract: Composite can deliver more than the individual elemental property of the material. Specifically chalcogenide- multi walled carbon nano tubes and chalcogenide- bilayer graphene composite materials could be interesting for the investigation, which have been less covered by the investigators. We describe micro structural properties of Se{sub 55}Te{sub 25}Ge{sub 20,} Se{sub 55}Te{sub 25}Ge{sub 20} + 0.025% multi walled carbon nano tubes and Se{sub 55}Te{sub 25}Ge{sub 20} + 0.025% bilayer graphene materials. This gives realization of the alloying constituents inclusion/or diffusion inside the multi walled carbon nano tubes and bilayer graphene under the homogeneous parent alloy configuration. Raman spectroscopy, X-ray photoelectron spectroscopy, UV/Visible spectroscopy and Fourier transmission infrared spectroscopy have also been carried out under the discussion. A considerable core energy levels peak shifts have been noticed for the composite materials by the X-ray photoelectron spectroscopy. The optical energy band gaps are measured to be varied in between 1.2 and 1.3 eV. In comparison to parent (Se{sub 55}Te{sub 25}Ge{sub 20}) alloy a higher infrared transmission has been observed for the composite materials. Subsequently, variation in physical properties has been explained on the basis of bond formation in solids.

  15. An integrated computational materials engineering method for woven carbon fiber composites preforming process

    Science.gov (United States)

    Zhang, Weizhao; Ren, Huaqing; Wang, Zequn; Liu, Wing K.; Chen, Wei; Zeng, Danielle; Su, Xuming; Cao, Jian

    2016-10-01

    An integrated computational materials engineering method is proposed in this paper for analyzing the design and preforming process of woven carbon fiber composites. The goal is to reduce the cost and time needed for the mass production of structural composites. It integrates the simulation methods from the micro-scale to the macro-scale to capture the behavior of the composite material in the preforming process. In this way, the time consuming and high cost physical experiments and prototypes in the development of the manufacturing process can be circumvented. This method contains three parts: the micro-scale representative volume element (RVE) simulation to characterize the material; the metamodeling algorithm to generate the constitutive equations; and the macro-scale preforming simulation to predict the behavior of the composite material during forming. The results show the potential of this approach as a guidance to the design of composite materials and its manufacturing process.

  16. Method of Making an Electroactive Sensing/Actuating Material for Carbon Nanotube Polymer Composite

    Science.gov (United States)

    Ounaies, Zoubeida (Inventor); Park, Cheol (Inventor); Harrison, Joycelyn S. (Inventor); Holloway, Nancy M. (Inventor); Draughon, Gregory K. (Inventor)

    2009-01-01

    An electroactive sensing or actuating material comprises a composite made from a polymer with polarizable moieties and an effective amount of carbon nanotubes incorporated in the polymer for a predetermined electromechanical operation of the composite when such composite is affected by an external stimulus. In another embodiment, the composite comprises a, third component of micro -sized to nano-sized particles of an electroactive ceramic that is also incorporated in the polymer matrix. The method for making the three-phase composite comprises either incorporating the carbon nanotubes in the polymer matrix before incorporation of the particles of ceramic or mixing the carbon nanotubes and particles of ceramic together in a solution before incorporation in the polymer matrix.

  17. Sensing/actuating materials made from carbon nanotube polymer composites and methods for making same

    Science.gov (United States)

    Ounaies, Zoubeida (Inventor); Park, Cheol (Inventor); Harrison, Joycelyn S. (Inventor); Holloway, Nancy M. (Inventor); Draughon, Gregory K. (Inventor)

    2008-01-01

    An electroactive sensing or actuating material comprises a composite made from a polymer with polarizable moieties and an effective amount of carbon nanotubes incorporated in the polymer for a predetermined electromechanical operation of the composite when such composite is affected by an external stimulus. In another embodiment, the composite comprises a third component of micro-sized to nano-sized particles of an electroactive ceramic that is also incorporated in the polymer matrix. The method for making the three-phase composite comprises either incorporating the carbon nanotubes in the polymer matrix before incorporation of the particles of ceramic or mixing the carbon nanotubes and particles of ceramic together in a solution before incorporation in the polymer matrix.

  18. Nanostructured composites based on carbon nanotubes and epoxy resin for use as radar absorbing materials

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Valdirene Aparecida [Instituto Tecnologico de Aeronautica (ITA), Sao Jose dos Campos, SP (Brazil); Folgueras, Luiza de Castro; Candido, Geraldo Mauricio; Paula, Adriano Luiz de; Rezende, Mirabel Cerqueira, E-mail: mirabelmcr@iae.cta.br [Instituto de Aeronautica e Espaco (IAE), Sao Jose dos Campos, SP (Brazil). Div. de Materiais; Costa, Michelle Leali [Universidade Estadual Paulista Julio de Mesquita Filho (DMT/UNESP), Guaratingueta, SP (Brazil). Dept. de Materiais e Tecnologia

    2013-07-01

    Nanostructured polymer composites have opened up new perspectives for multifunctional materials. In particular, carbon nanotubes (CNTs) present potential applications in order to improve mechanical and electrical performance in composites with aerospace application. The combination of epoxy resin with multi walled carbon nanotubes results in a new functional material with enhanced electromagnetic properties. The objective of this work was the processing of radar absorbing materials based on formulations containing different quantities of carbon nanotubes in an epoxy resin matrix. To reach this objective the adequate concentration of CNTs in the resin matrix was determined. The processed structures were characterized by scanning electron microscopy, rheology, thermal and reflectivity in the frequency range of 8.2 to 12.4 GHz analyses. The microwave attenuation was up to 99.7%, using only 0.5% (w/w) of CNT, showing that these materials present advantages in performance associated with low additive concentrations (author)

  19. Analysis and optimization of temperature distribution in carbon fiber reinforced composite materials during microwave curing process

    OpenAIRE

    2014-01-01

    Vacuum assisted microwave curing technologies and modified optical sensing systems have been employed to investigate the influence of ply orientation and thickness on through-thickness temperature distribution of carbon fiber reinforced composite laminates. Two different types of epoxy systems have been studied. The results demonstrated that the ply orientation did not affect the temperature distribution of composite materials. However, the thickness was an important influencing factor. Nearl...

  20. Size Classification of Chopped Carbon Fibers in the Composite Materials Manufacturing

    Directory of Open Access Journals (Sweden)

    А.S. Dovbysh

    2010-01-01

    Full Text Available Information synthesis of the learning decision support system for automation of the chopped carbon fibers size control used for the matrix filling within the manufacturing of composite materials based on polytetrafluoroethylene is considered. To improve the reliability of recognition learning algorithm with the optimization of the precision control is proposed.

  1. Size Classification of Chopped Carbon Fibers in the Composite Materials Manufacturing

    OpenAIRE

    А.S. Dovbysh; А.F. Budnik; N.І. Andriienko

    2010-01-01

    Information synthesis of the learning decision support system for automation of the chopped carbon fibers size control used for the matrix filling within the manufacturing of composite materials based on polytetrafluoroethylene is considered. To improve the reliability of recognition learning algorithm with the optimization of the precision control is proposed.

  2. Composite carbon foam electrode

    Energy Technology Data Exchange (ETDEWEB)

    Mayer, S.T.; Pekala, R.W.; Kaschmitter, J.L.

    1997-05-06

    Carbon aerogels used as a binder for granulated materials, including other forms of carbon and metal additives, are cast onto carbon or metal fiber substrates to form composite carbon thin film sheets. The thin film sheets are utilized in electrochemical energy storage applications, such as electrochemical double layer capacitors (aerocapacitors), lithium based battery insertion electrodes, fuel cell electrodes, and electrocapacitive deionization electrodes. The composite carbon foam may be formed by prior known processes, but with the solid particles being added during the liquid phase of the process, i.e. prior to gelation. The other forms of carbon may include carbon microspheres, carbon powder, carbon aerogel powder or particles, graphite carbons. Metal and/or carbon fibers may be added for increased conductivity. The choice of materials and fibers will depend on the electrolyte used and the relative trade off of system resistivity and power to system energy. 1 fig.

  3. Composite carbon foam electrode

    Energy Technology Data Exchange (ETDEWEB)

    Mayer, Steven T. (San Leandro, CA); Pekala, Richard W. (Pleasant Hill, CA); Kaschmitter, James L. (Pleasanton, CA)

    1997-01-01

    Carbon aerogels used as a binder for granularized materials, including other forms of carbon and metal additives, are cast onto carbon or metal fiber substrates to form composite carbon thin film sheets. The thin film sheets are utilized in electrochemical energy storage applications, such as electrochemical double layer capacitors (aerocapacitors), lithium based battery insertion electrodes, fuel cell electrodes, and electrocapacitive deionization electrodes. The composite carbon foam may be formed by prior known processes, but with the solid particles being added during the liquid phase of the process, i.e. prior to gelation. The other forms of carbon may include carbon microspheres, carbon powder, carbon aerogel powder or particles, graphite carbons. Metal and/or carbon fibers may be added for increased conductivity. The choice of materials and fibers will depend on the electrolyte used and the relative trade off of system resistivty and power to system energy.

  4. Composite Materials

    DEFF Research Database (Denmark)

    Nielsen, Lauge Fuglsang

    This book deals with the mechanical and physical behavior of composites as influenced by composite geometry. "Composite Materials" provides a comprehensive introduction for researchers and students to modern composite materials research with a special emphasis on the significance of phase geometry....... The book enables the reader to a better understanding of the behavior of natural composites, improvement of such materials, and design of new materials with prescribed properties. A number of examples are presented: Special composite properties considered are stiffness, shrinkage, hygro-thermal behavior......, viscoelastic behavior, and internal stress states. Other physical properties considered are thermal and electrical conductivities, diffusion coefficients, dielectric constants and magnetic permeability. Special attention is given to the effect of pore shape on the mechanical and physical behavior of porous...

  5. Multiwalled carbon nanotube-reinforced ceramic matrix composites as a promising structural material

    Energy Technology Data Exchange (ETDEWEB)

    Estili, Mehdi, E-mail: mehdiestili@gmail.co [Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Department of Materials Processing, Graduate School of Engineering, Tohoku University, Sendai 980-8579 (Japan); Kwon, Hansang; Kawasaki, Akira; Cho, Seungchan; Takagi, Kenta; Kikuchi, Keiko [Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Kawai, Masayoshi [Institute of Materials Structure Science, High Energy Accelerator Research Organization, Oho, Tsukuba, Ibaraki 305-0801 (Japan)

    2010-03-15

    In this paper, we introduce fully dense, multiwalled carbon nanotube (MWCNT)-reinforced ceramic matrix composites recently processed by a novel powder technology in our laboratory to be considered as a promising potential structural materials for employment in severe working conditions. A strategy is also offered to investigate the effect of working condition on the mechanical properties of MWCNTs embedded in the ceramic matrix for a reliable material selection for the working conditions needed.

  6. Biomechanical properties of an advanced new carbon/flax/epoxy composite material for bone plate applications.

    Science.gov (United States)

    Bagheri, Zahra S; El Sawi, Ihab; Schemitsch, Emil H; Zdero, Rad; Bougherara, Habiba

    2013-04-01

    This work is part of an ongoing program to develop a new carbon fiber/flax/epoxy (CF/flax/epoxy) hybrid composite material for use as an orthopaedic long bone fracture plate, instead of a metal plate. The purpose of this study was to evaluate the mechanical properties of this new novel composite material. The composite material had a "sandwich structure", in which two thin sheets of CF/epoxy were attached to each outer surface of the flax/epoxy core, which resulted in a unique structure compared to other composite plates for bone plate applications. Mechanical properties were determined using tension, three-point bending, and Rockwell hardness tests. Also, scanning electron microscopy (SEM) was used to characterize the failure mechanism of specimens in tension and three-point bending tests. The results of mechanical tests revealed a considerably high ultimate strength in both tension (399.8MPa) and flexural loading (510.6MPa), with a higher elastic modulus in bending tests (57.4GPa) compared to tension tests (41.7GPa). The composite material experienced brittle catastrophic failure in both tension and bending tests. The SEM images, consistent with brittle failure, showed mostly fiber breakage and fiber pull-out at the fractured surfaces with perfect bonding at carbon fibers and flax plies. Compared to clinically-used orthopaedic metal plates, current CF/flax/epoxy results were closer to human cortical bone, making the material a potential candidate for use in long bone fracture fixation.

  7. Enhancement of Electrochemical Stability about Silicon/Carbon Composite Anode Materials for Lithium Ion Batteries

    Directory of Open Access Journals (Sweden)

    Wei Xiao

    2015-01-01

    Full Text Available Silicon/carbon (Si/C composite anode materials are successfully synthesized by mechanical ball milling followed by pyrolysis method. The structure and morphology of the composite are characterized by X-ray diffraction and scanning electron microscopy and transmission electron microscope, respectively. The results show that the composite is composed of Si, flake graphite, and phenolic resin-pyrolyzed carbon, and Si and flake graphite are enwrapped by phenolic resin-pyrolyzed carbon, which can provide not only a good buffering matrix but also a conductive network. The Si/C composite also shows good electrochemical stability, in which the composite anode material exhibits a high initial charge capacity of 805.3 mAh g−1 at 100 mA g−1 and it can still deliver a high charge capacity of 791.7 mAh g−1 when the current density increases to 500 mA g−1. The results indicate that it could be used as a promising anode material for lithium ion batteries.

  8. Carbon-coated LiFePO4-porous carbon composites as cathode materials for lithium ion batteries.

    Science.gov (United States)

    Ni, Haifang; Liu, Jinkun; Fan, Li-Zhen

    2013-03-07

    This work introduces a facile strategy for the synthesis of carbon-coated LiFePO(4)-porous carbon (C-LiFePO(4)-PC) composites as a cathode material for lithium ion batteries. The LiFePO(4) particles obtained are about 200 nm in size and homogeneously dispersed in porous carbon matrix. These particles are further coated with the carbon layers pyrolyzed from sucrose. The C-LiFePO(4)-PC composites display a high initial discharge capacity of 152.3 mA h g(-1) at 0.1 C, good cycling stability, as well as excellent rate capability (112 mA h g(-1) at 5 C). The likely contributing factors to the excellent electrochemical performance of the C-LiFePO(4)-PC composites could be related to the combined effects of enhancement of conductivity by the porous carbon matrix and the carbon coating layers. It is believed that further carbon coating is a facile and effective way to improve the electrochemical performance of LiFePO(4)-PC.

  9. Multiscale Modeling of Carbon/Phenolic Composite Thermal Protection Materials: Atomistic to Effective Properties

    Science.gov (United States)

    Arnold, Steven M.; Murthy, Pappu L.; Bednarcyk, Brett A.; Lawson, John W.; Monk, Joshua D.; Bauschlicher, Charles W., Jr.

    2016-01-01

    Next generation ablative thermal protection systems are expected to consist of 3D woven composite architectures. It is well known that composites can be tailored to achieve desired mechanical and thermal properties in various directions and thus can be made fit-for-purpose if the proper combination of constituent materials and microstructures can be realized. In the present work, the first, multiscale, atomistically-informed, computational analysis of mechanical and thermal properties of a present day - Carbon/Phenolic composite Thermal Protection System (TPS) material is conducted. Model results are compared to measured in-plane and out-of-plane mechanical and thermal properties to validate the computational approach. Results indicate that given sufficient microstructural fidelity, along with lowerscale, constituent properties derived from molecular dynamics simulations, accurate composite level (effective) thermo-elastic properties can be obtained. This suggests that next generation TPS properties can be accurately estimated via atomistically informed multiscale analysis.

  10. Simplified identification of compounding ratio and dispersion of Carbon nanotube / Polymer composite material

    Science.gov (United States)

    Wakiwaka, Hiroyuki; Kumakura, Yoichi; Endo, Morinobu

    In order to obtain the physical property of polypropylene and vapor growth carbon fiber (VGCF) composite material, a novel contact probe structure, C-probe, for the measurement of static capacitor is proposed. The present method utilizes the difference in dielectric constant of composite depending on the VGCF concentration. The C-probe contacted to the surface of the measuring object measures the resonance frequency between the electrodes arranged in plane (horizontal structure). In comparison with the conventional capacitor method, in which the specimen is clamped between the electrodes (vertical structure), the C-probe is advantageous because it realizes quick and non-destructive measurement. The experimental result shows good relationship between the compound ratio and the resonance frequency. By decreasing the dimension of the C-probe to be less than the composite specimen, the dispersion of mixture of the composite material has been also identified successfully.

  11. Composite material

    Science.gov (United States)

    Hutchens, Stacy A.; Woodward, Jonathan; Evans, Barbara R.; O'Neill, Hugh M.

    2012-02-07

    A composite biocompatible hydrogel material includes a porous polymer matrix, the polymer matrix including a plurality of pores and providing a Young's modulus of at least 10 GPa. A calcium comprising salt is disposed in at least some of the pores. The porous polymer matrix can comprise cellulose, including bacterial cellulose. The composite can be used as a bone graft material. A method of tissue repair within the body of animals includes the steps of providing a composite biocompatible hydrogel material including a porous polymer matrix, the polymer matrix including a plurality of pores and providing a Young's modulus of at least 10 GPa, and inserting the hydrogel material into cartilage or bone tissue of an animal, wherein the hydrogel material supports cell colonization in vitro for autologous cell seeding.

  12. A Study on Accelerated Thermal Aging of High Modulus Carbon/Epoxy Composite Material

    Directory of Open Access Journals (Sweden)

    Ju Min Kyung

    2015-01-01

    Full Text Available Composite materials have been used increasingly for various space applications due to the favorable characteristic of high modulus to density ratio and potential for near-zero coefficient of thermal expansion. In composite system, depending on the orientation of fibers, strength and stiffness can be changed so that the optimum structure can be accomplished. This is because the coefficient of thermal expansion (CTE of carbon fibers is negative. For spacecraft and orbiting space structure, which are thermally cycled by moving through the earth' shadow for at least 5 years, it is necessary to investigate the change of properties of the material over time. In this study, thermal aging of epoxy matrix/high modulus carbon fiber composite materials are accelerated to predict the long term creep property. Specimens are tested at various temperatures of 100~140°C with dynamic mechanical analysis to obtain creep compliances that are functions of time and temperature. Using Time Temperature Superposition method, creep compliance curves at each temperature are shifted to the reference temperature by shift factor and a master curve is generated at the reference temperature. This information is useful to predict the long term thermal aging of high modulus composite material for spacecraft application.

  13. Optical properties of carbon materials filled HDPE composites in THz region

    Institute of Scientific and Technical Information of China (English)

    CHEN Xiliang; MA Mingwang; YANG Xiaomin; YANG Kang; LIU Dan; JI Te; WU Shengwei; ZHU Zhiyong

    2009-01-01

    The optical and electrical properties of several composites,formed by filling the high density polyethylene (HDPE) with similar amount of carbon black (CB),multi-walled carbon nanotubes (MWNT) and fullerene (C60),respectively,were characterized using a THz-TDS setup.It was found that the optical parameters and the details of their variation with frequency differ significantly for different kinds of carbon materials.The results are analyzed by using Cole-Cole formula of dipole relaxation under the assumption that carbon particles dispersed in the matrix behave like dipoles and contribute mainly to the dielectric loss in the THz frequency range.Fitting results indicate that MWNT and CB filled composites have a broader distribution of the relaxation time compared with C60 which possesses a nearly single relaxation time.Compared with CB and C60,MWNT filled composite possesses the larger relaxation strength due to its higher electron density and larger conductive clusters.The real part of conductivity for three kinds of composites all follows power law behavior with respect to frequency but the exponents are quite different.These phenomena may be related to the special properties of the fillers as well as their particulate structures,such as aspect ratio,particle size,and aggregate structure,etc.

  14. A mediatorless microbial fuel cell using polypyrrole coated carbon nanotubes composite as anode material

    Energy Technology Data Exchange (ETDEWEB)

    Zou, Yongjin; Xiang, Cuili; Yang, Lini [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100049 (China); Sun, Li-Xian [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); School of Chemistry and Environmental Engineering, Changsha University of Science and Technology, Changsha 410076 (China); Xu, Fen [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Cao, Zhong [School of Chemistry and Environmental Engineering, Changsha University of Science and Technology, Changsha 410076 (China)

    2008-09-15

    A microbial fuel cell (MFC) was constructed using polypyrrole (PPy) coated carbon nanotubes (CNTs) composite as an anode material and Escherichia coli as the biocatalyst. The composite PPy-CNTs were synthesized by the in situ chemical polymerization of pyrrole on the CNTs using ammonium persulfate as an oxidant. The electrocatalytic behaviors of the composite modified anode were investigated by means of cyclic voltammetry, electrochemical impedance spectroscopy and discharge experiments. The PPy-CNTs modified anode showed better electrochemical performance than that of plain carbon paper. The amount of the loading of the composite on the anode was also investigated. The power output of the MFC increased along with the increase of the composite loading. In the absence of exogenous electron mediators, the MFC with the composite modified anode contained 5 mg cm{sup -2} PPy-CNTs exhibited a maximum power density 228 mW m{sup -2}, which is much higher than those reported in the literature so far for E. coli using efficient electron mediators. These results show that the PPy-CNTs composite anode is promising for MFC application. (author)

  15. Carbon/graphite composite material study. Appendix C: NASA studies on modification of carbon/graphite fibers and alternative materials

    Science.gov (United States)

    1981-01-01

    The feasibility of modifying resin matrix composites to reduce the potential of electrical shorting from fire released fiber was explored. The effort included modifications to or coatings for graphite fibers, alternative fibers, modifications to matrix materials, and hybrid composites. The objectives included reduction of the conductivity of the graphite fiber, char formation to reduce fiber release, glass formation to prevent fiber release, catalysis to assure fiber consumption in a fire, and replacement of the graphite fibers with nonconductive fibers of similar mechanical potential.

  16. Compression Molding of Chemical/Thermal Resistant Composite Materials Using Wastes of Glass Fiber Reinforced PTFE and Carbon Fiber

    OpenAIRE

    Kimura, Teruo

    2013-01-01

    This report proposed the compression molding method of chemical/thermal resistant composite materials reinforced by the carbon fiber extracted from CFRP waste and the waste of glass fiber coated by PTFE. The FEP resin was used for the matrix material. The contents of carbon fiber and FEP resin were varied in the experiments, and the machanical properties of composite materials were discussed in detail. As a result, the bending strength and modulus increased with increasing the content of carb...

  17. Prediction of Thermophysical and Thermomechanical Characteristics of Porous Carbon-Ceramic Composite Materials of the Heat Shield of Aerospace Craft

    Science.gov (United States)

    Reznik, S. V.; Prosuntsov, P. V.; Mikhailovskii, K. V.

    2015-05-01

    A procedure for predicting thermophysical and thermomechanical characteristics of porous carbon-ceramic composite materials of the heat shield of aerospace craft as functions of the type of reinforcement, porosity of the structure, and the characteristics of the material's components has been developed. Results of mathematical modeling of the temperature and stressed-strained states of representative volume elements for determining the characteristics of a carbon-ceramic composite material with account taken of its anisotropy have been given.

  18. Aspects regarding wearing behaviour in case of aluminium composite materials reinforced with carbon fibers

    Science.gov (United States)

    Caliman, R.

    2016-08-01

    This paper presents a study regarding wear comportment of sintered composite materials obtained by mixture of aluminium with short carbon fibers. The necessity to satisfying more and more the specific functions during design of high performance structures leads to perform multi-materials such as reinforced composite parts. The wear tests were made on three different orientations of fibers on a standard machine of tribology, pin disk type. Counter-disk was made of cast iron with a superficial hardness of 92 HB. The wear rate and friction coefficient decreased exponentially with time of friction and reached a stationary value. This behaviour was attributed to the development of a lubricating film on the friction surface. To conduct this work was performed measurements on samples from the Al matrix composites and carbon fiber 43%, wear mechanism was investigated by scanning electron microscopy. In addition to fiber orientation, the tribological behaviour of metal matrix composites reinforced with fiber is influenced by the interfacial reaction of fiber-matrix. The characteristics and the dimensions of the interface depend on the cycle of temperature and time at which the material has been subjected during the manufacturing process and thereafter.

  19. Polyaniline nanofiber/large mesoporous carbon composites as electrode materials for supercapacitors

    Science.gov (United States)

    Liu, Huan; Xu, Bin; Jia, Mengqiu; Zhang, Mei; Cao, Bin; Zhao, Xiaonan; Wang, Yu

    2015-03-01

    A composite of polyaniline nanofiber/large mesoporous carbon (PANI-F/LMC) hybrid was prepared by an in situ chemical oxidative polymerization of aniline monomer with nano-CaCO3 templated LMC as host matrix for supercapacitors. The morphology, composition and electronic structure of the composites (PANI-F/LMC) together with pure PANI nanofibers and the LMC were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), FT-IR, X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). It is found that the PANI nanofibers were incorporated into the large mesochannels of LMC with interpenetrating framework formed. Such unique structure endows the PANI-F/LMC composite with a high capacitance of 473 F g-1 at a current load of 0.1 A g-1 with good rate performance and cycling stability, suggesting its potential application in the electrode material for supercapacitors.

  20. Nano-engineered Multiwall Carbon Nanotube-copper Composite Thermal Interface Material for Efficient Heat Conduction

    Science.gov (United States)

    Ngo, Quoc; Cruden, Brett A.; Cassell, Alan M.; Sims, Gerard; Li, Jun; Meyyappa, M.; Yang, Cary Y.

    2005-01-01

    Efforts in integrated circuit (IC) packaging technologies have recently been focused on management of increasing heat density associated with high frequency and high density circuit designs. While current flip-chip package designs can accommodate relatively high amounts of heat density, new materials need to be developed to manage thermal effects of next-generation integrated circuits. Multiwall carbon nanotubes (MWNT) have been shown to significantly enhance thermal conduction in the axial direction and thus can be considered to be a candidate for future thermal interface materials by facilitating efficient thermal transport. This work focuses on fabrication and characterization of a robust MWNT-copper composite material as an element in IC package designs. We show that using vertically aligned MWNT arrays reduces interfacial thermal resistance by increasing conduction surface area, and furthermore, the embedded copper acts as a lateral heat spreader to efficiently disperse heat, a necessary function for packaging materials. In addition, we demonstrate reusability of the material, and the absence of residue on the contacting material, both novel features of the MWNT-copper composite that are not found in most state-of-the-art thermal interface materials. Electrochemical methods such as metal deposition and etch are discussed for the creation of the MWNT-Cu composite, detailing issues and observations with using such methods. We show that precise engineering of the composite surface affects the ability of this material to act as an efficient thermal interface material. A thermal contact resistance measurement has been designed to obtain a value of thermal contact resistance for a variety of different thermal contact materials.

  1. Carbon nanotube bundles/polystyrene composites as high-performance flexible thermoelectric materials

    Science.gov (United States)

    Suemori, Kouji; Watanabe, Yuichi; Hoshino, Satoshi

    2015-03-01

    Lightweight and flexible thermoelectric devices consisting of carbon nanotube (CNT)-based materials have the potential to be used for the various applications, such as energy harvesting from the low-temperature waste heat that exists ubiquitously in living areas. Because high-performance CNT-based materials are crucial for the broad-ranging employment of CNT-based thermoelectric devices, considerable efforts are being made to improve the power-generation capability of CNT-based thermoelectric materials. Here, we report high-performance thermoelectric composites consisting of CNT bundles and polystyrene fabricated by a planetary ball milling-based dispersion technique, which allows for the direct dispersion of the CNT bundles within the polystyrene matrix without causing the disaggregation of the bundled CNTs into individual ones. The CNT-bundles/polystyrene composites reported here exhibit a power factor of 413 μW/K2.m.

  2. Fabrication of porous carbon composite material from leaves waste as lightweight expanded carbon aggregate (LECA)

    Science.gov (United States)

    Sulhadi, Rosita, N.; Susanto, Nisa', K.; Wiguna, P. A.; Marwoto, P.; Aji, M. P.

    2016-04-01

    Leaves waste has been used as Lightweight Expanded Carbon Aggregates (LECA) because of its high carbon material. LECA can be used as a water storage media. LECA is low in density so thatits massis very light. Due to its use as a water storage medium, it is important to find out the absorption which occurs in LECA.The LECA's absorption and evaporation rate is affected by the pores. The pores serves to increase water storage ability from LECA. LECA with PEG (pore-forming agent) mass percent variation of 5%, 10%, 15%, 20% and 25% is the focus of this study. LECA fabrication was conducted by mixing the carbon resulting from leaves waste pyrolysis and PEG and PVAc. The characterization of LECA was found out by calculating the porosity, the pore size distribution, absorption rate and evaporation rate. The result of the calculation shows that the higher PEG mass percentage, the higher LECA's porosity, the pore size distribution, absorption rate and evaporation rate. However, the porosity, the pore size distributionand absorption rate will be saturated by 25% PEG mass percent addition.

  3. Composite material based on an ablative phenolic resin and carbon fibers

    Directory of Open Access Journals (Sweden)

    DIMKO DIMESKI

    2009-04-01

    Full Text Available In this study, a technological procedure for the production of a molding compound based on short carbon fibers and an ablative phenol–formaldehyde resin for high temperature application was optimized. The starting raw materials were characterized and molding compounds with different fiber/matrix ratios and different fiber lengths were obtained. From the different laboratory samples, molded parts were made by thermocompression. The basic mechanical and thermal properties of the composites were determined. From the obtained results, the optimal fiber/matrix ratio was determined for a production of molding compound for high temperature application. The molding process of the composite material was optimized and all the parameters for good mechanical properties and high thermal stability of the composite were obtained. Optimization of the composite molding process was performed by the application of a numerical method for a planned experiment, i.e., a full three-factorial experimental design with variance of all three parameters (fiber length, temperature and time of the press cycle on two levels. The obtained mechanical properties (flexural strength: 247 MPa, modulus: 27.6 GPa, impact resistance: 110 (for test moldings 10 mm´10 mm and 91 kJ/m2 (for test moldings 15 mm´15 mm justified the application of this composite material in the automotive, leisure, military and other industries where high temperature resistance and high mechanical strength is required.

  4. Collagen-carbon nanotube composite materials as scaffolds in tissue engineering.

    Science.gov (United States)

    MacDonald, Rebecca A; Laurenzi, Brendan F; Viswanathan, Gunaranjan; Ajayan, Pulickel M; Stegemann, Jan P

    2005-09-01

    Carbon nanotubes (CNT) are attractive for use in fiber-reinforced composite materials due to their very high aspect ratio, combined with outstanding mechanical and electrical properties. Composite materials comprising a collagen matrix with embedded CNT were prepared by mixing solubilized Type I collagen with solutions of carboxylated single-walled carbon nanotubes (SWNT) at concentrations of 0, 0.2, 0.4, 0.8, and 2.0 weight percent. Living smooth muscle cells were incorporated at the time of collagen gelation to produce cell-seeded collagen-CNT composite matrices. Constructs containing 2.0 wt % CNT exhibited delayed gel compaction, relative to lower concentrations that compacted at the same rate as pure collagen controls. Cell viability in all constructs was consistently above 85% at both Day 3 and Day 7, whereas cell number in CNT-containing constructs was lower than in control constructs at Day 3, though statistically unchanged by Day 7. Scanning electron microscopy showed physical interactions between CNT and collagen matrix. Raman spectroscopy confirmed the presence of CNT at the expected diameter (0.85-1.30 nm), but did not indicate strong molecular interactions between the collagen and CNT components. Such collagen-CNT composite matrices may have utility as scaffolds in tissue engineering, or as components of biosensors or other medical devices.

  5. Carbon Nanofibers (CNFs) Surface Modification to Fabricate Carbon Nanofibers_Nanopaper Integrated Polymer Composite Material.

    Science.gov (United States)

    Jiang, Jianjun; Zhao, Ziwei; Deng, Chao; Liu, Fa; Li, Dejia; Fang, Liangchao; Zhang, Dan; Castro Jose M; Chen, Feng; Lee, L James

    2016-06-01

    Carbon Nanofibers (CNFs) have shown great potential to improve the physical and mechanical properties of conventional Fiber Reinforced Polymer Composites (FRPCs) surface. Excellent dispersion CNFs into water or polymer matrix was very crucial to get good quality CNFs enhanced FRPCs. Because of the hydrophobic properties of CNFs, we apply the reversible switching principles to transfer the hydrophobic surface into hydrophilic surface by growing polyaniline nanograss on the surface of CNFs which was carried out in hydrochloric acid condition. Incorporating CNFs into FRPCs as a surface layer named CNFs Nanopaper to increase the erosion resistance and electrical conductivity in this research which was very important in the wind energy field. In order to get high quality dispersed CNFs suspension, a sonication unit was used to detangle and uniform disperse the functionalized CNFs. A filter with vacuum pressure used to filter the suspension of CNFs onto Carbon veil to make CNFs Nanopaper. Vacuum Aided Resin Transfer Modeling (VARTM) process was used to fabricate Nano-enhanced FRPCs samples. In order to characterize the mechanical properties, three point bending experiment was measured. The flexural strength capacity and deformation resistance and behavior were compared and analyzed. In this paper, we discussed the methods used and provided experimental parameter and experimental results.

  6. STRUCTURE AND PROPERTIES OF COMPOSITE MATERIAL BASED ON GYPSUM BINDER AND CARBON NANOTUBES

    Directory of Open Access Journals (Sweden)

    CHUMAK Anastasia Gennadievna

    2013-04-01

    Full Text Available The aim of this work is to carry out a number of studies in the area of nanomodi­fication of gypsum binder matrix and to investigate the influence of multilayer carbon nanotubes on the structure, physical and mechanical properties of obtained compos­ites. The study of the gypsum binders structure formation mechanisms with the use of nanoadditives makes it possible to control the production processes of gypsum materi­als and articles with the given set of properties. The main tasks of the binder nanomodification are: even distribution of carbon nanostructures over the whole volume of material and provision of stability for the nanodimensional modifier during production process of the construction composite.

  7. Alumina supported carbon composite material with exceptionally high defluoridation property from eggshell waste.

    Science.gov (United States)

    Lunge, Sneha; Thakre, Dilip; Kamble, Sanjay; Labhsetwar, Nitin; Rayalu, Sadhana

    2012-10-30

    A new alumina supported carbon composite material called "Eggshell Composite" (EC) was synthesized from eggshell waste as calcium source for selective fluoride adsorption from water. The effect of various synthesis parameters like eggshell (ES): Eggshell membrane (ESM) ratio, aluminium loading, mixing time and calcinations temperature to optimize the synthesis conditions for selective fluoride removal has been studied. It was observed that the synthesis parameters have significant influence on development of EC and in turn on fluoride removal capacity. EC synthesized was characterized for elemental composition, morphology, functionality and textural properties. Results showed that EC obtained from eggshell modified with alumina precursor is more selective and efficient for fluoride removal. Langmuir and Freundlich isotherm were used to obtain ultimate fluoride removal capacity. The calcium and alumina species in EC shows synergistic effect in fluoride adsorption process. Fluoride sorption studies were carried out in synthetic, groundwater and wastewater. EC proved to be a potential, indigenous and economic adsorbent for fluoride removal.

  8. Polythiophene-carbon nanotubes composites as energy storage materials for supercapacitor application

    Science.gov (United States)

    Thakur, A. K.; Choudhary, R. B.; Sartale, S. D.; Desai, Mangesh

    2016-05-01

    Polythiophene incorporated carbon materials have sought huge attention due to various improved electrochemical properties including enhanced electrical conductivity. Our work includes the synthesis of polythiophene (PTP)-multi-wallcarbon nanotubes (MWCNTs) via in-situ polymerization method. The homogeneous distribution of MWCNT in PTP was confirmed by Field Emission Scanning Electron Microscope (FESEM). Examination of the specimen using X-Ray diffraction (XRD), Fourier Transform-Infrared (FTIR) and Raman spectroscopy confirmed the composite formation. Other electrochemical characterizations like electrochemical impendence spectroscopy (EIS) and cyclic voltammetry (CV)of the PTP-MWCNT composite affirmed that incorporation of MWCNT improves the electrochemical properties of neat PTP including a significant increase in the capacitance. Hence making PTP-MWCNT isa better material for supercapacitor application than neat PTP.

  9. Infiltrated carbon foam composites

    Science.gov (United States)

    Lucas, Rick D. (Inventor); Danford, Harry E. (Inventor); Plucinski, Janusz W. (Inventor); Merriman, Douglas J. (Inventor); Blacker, Jesse M. (Inventor)

    2012-01-01

    An infiltrated carbon foam composite and method for making the composite is described. The infiltrated carbon foam composite may include a carbonized carbon aerogel in cells of a carbon foam body and a resin is infiltrated into the carbon foam body filling the cells of the carbon foam body and spaces around the carbonized carbon aerogel. The infiltrated carbon foam composites may be useful for mid-density ablative thermal protection systems.

  10. Lyocell Based Carbon Carbon Composite for Use as a Large Exit Cone Material Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA Office of the Chief Technologist (OCT) has identified a "carbon-carbon nozzle (domestic source)" as a "Top Technical Challenge" in the 2011-2016 timeframe...

  11. Mechanical properties of several neat polymer matrix materials and unidirectional carbon fiber-reinforced composites

    Science.gov (United States)

    Coguill, Scott L.; Adams, Donald F.

    1989-01-01

    The mechanical and physical properties of three neat matrix materials, i.e., PEEK (polyetheretherketone) thermoplastic, Hexcel F155 rubber-toughened epoxy and Hercules 8551-7 rubber-toughened epoxy, were experimentally determined. Twelve unidirectional carbon fiber composites, incorporating matrix materials characterized in this or earlier studies (with one exception; the PISO(sub 2)-TPI matrix itself was not characterized), were also tested. These composite systems included AS4/2220-1, AS4/2220-3, T500/R914, IM6/HX1504, T300/4901A (MDA), T700/4901A (MDA), T300/4901B (MPDA), T700/4901B (MPDA), APC2 (AS4/PEEK, ICI), APC2 (AS4/PEEK, Langley Research Center), AS4/8551-7, and AS4/PISO(sub 2)-TPI. For the neat matrix materials, the tensile, shear, fracture toughness, coefficient of thermal expansion, and coefficient of moisture expansion properties were measured as a function of both temperature and moisture content. For the unidirectional composites, axial and transverse tensile, longitudinal shear, coefficient of thermal expansion, and coefficient of moisture expansion properties were determined, at room temperature and 100 C.

  12. Hierarchically ordered mesoporous carbon/graphene composites as supercapacitor electrode materials.

    Science.gov (United States)

    Song, Yanjie; Li, Zhu; Guo, Kunkun; Shao, Ting

    2016-08-25

    Hierarchically ordered mesoporous carbon/graphene (OMC/G) composites have been fabricated by means of a solvent-evaporation-induced self-assembly (EISA) method. The structures of these composites are characterized by X-ray diffraction, transmission electron microscopy, Raman spectroscopy and nitrogen adsorption-desorption at 77 K. These results indicate that OMC/G composites possess the hierarchically ordered hexagonal p6mm mesostructure with the lattice unit parameter and pore diameter close to 10 nm and 3 nm, respectively. The specific surface area of OMC/G composites after KOH activation is high up to 2109.2 m(2) g(-1), which is significantly greater than OMC after activation (1474.6 m(2) g(-1)). Subsequently, the resulting OMC/G composites as supercapacitor electrode materials exhibit an outstanding capacitance as high as 329.5 F g(-1) in 6 M KOH electrolyte at a current density of 0.5 A g(-1), which is much higher than both OMC (234.2 F g(-1)) and a sample made by mechanical mixing of OMC with graphene (217.7 F g(-1)). In addition, the obtained OMC/G composites display good cyclic stability, and the final capacitance retention is approximately 96% after 5000 cycles. These ordered mesopores in the OMC/G composites are beneficial to the accessibility and rapid diffusion of the electrolyte, while graphene in OMC/G composites can also facilitate the transport of electrons during the processes of charging and discharging owing to its high conductivity, thereby leading to an excellent energy storage performance. The method demonstrated in this work would open up a new route to design and develop graphene-based architectures for supercapacitor applications.

  13. Mechanical properties of neat polymer matrix materials and their unidirectional carbon fiber-reinforced composites

    Science.gov (United States)

    Zimmerman, Richard S.; Adams, Donald F.

    1988-01-01

    The mechanical properties of two neat resin systems for use in carbon fiber epoxy composites were characterized. This included tensile and shear stiffness and strengths, coefficients of thermal and moisture expansion, and fracture toughness. Tests were conducted on specimens in the dry and moisture-saturated states, at temperatures of 23, 82 and 121 C. The neat resins tested were American Cyanamid 1806 and Union Carbide ERX-4901B(MPDA). Results were compared to previously tested neat resins. Four unidirectional carbon fiber reinforced composites were mechanically characterized. Axial and transverse tension and in-plane shear strengths and stiffness were measured, as well as transverse coefficients of thermal and moisture expansion. Tests were conducted on dry specimens only at 23 and 100 C. The materials tested were AS4/3502, AS6/5245-C, T300/BP907, and C6000/1806 unidirectional composites. Scanning electron microscopic examination of fracture surfaces was performed to permit the correlation of observed failure modes with the environmental test conditions.

  14. Electrical percolation threshold of cementitious composites possessing self-sensing functionality incorporating different carbon-based materials

    Science.gov (United States)

    Al-Dahawi, Ali; Haroon Sarwary, Mohammad; Öztürk, Oğuzhan; Yıldırım, Gürkan; Akın, Arife; Şahmaran, Mustafa; Lachemi, Mohamed

    2016-10-01

    An experimental study was carried out to understand the electrical percolation thresholds of different carbon-based nano- and micro-scale materials in cementitious composites. Multi-walled carbon nanotubes (CNTs), graphene nanoplatelets (GNPs) and carbon black (CB) were selected as the nano-scale materials, while 6 and 12 mm long carbon fibers (CF6 and CF12) were used as the micro-scale carbon-based materials. After determining the percolation thresholds of different electrical conductive materials, mechanical properties and piezoresistive properties of specimens produced with the abovementioned conductive materials at percolation threshold were investigated under uniaxial compressive loading. Results demonstrate that regardless of initial curing age, the percolation thresholds of CNT, GNP, CB and CFs in ECC mortar specimens were around 0.55%, 2.00%, 2.00% and 1.00%, respectively. Including different carbon-based conductive materials did not harm compressive strength results; on the contrary, it improved overall values. All cementitious composites produced with carbon-based materials, with the exception of the control mixtures, exhibited piezoresistive behavior under compression, which is crucial for sensing capability. It is believed that incorporating the sensing attribute into cementitious composites will enhance benefits for sustainable civil infrastructures.

  15. Photocatalytic degradation of an azo-dye on TiO2/activated carbon composite material.

    Science.gov (United States)

    Andriantsiferana, C; Mohamed, E F; Delmas, H

    2014-01-01

    A sequential adsorption/photocatalytic regeneration process to remove tartrazine, an azo-dye in aqueous solution, has been investigated. The aim ofthis work was to compare the effectiveness of an adsorbent/photocatalyst composite-TiO2 deposited onto activated carbon (AC) - and a simple mixture of powders of TiO2 and AC in same proportion. The composite was an innovative material as the photocatalyst, TiO2, was deposited on the porous surface ofa microporous-AC using metal-organic chemical vapour deposition in fluidized bed. The sequential process was composed of two-batch step cycles: every cycle alternated a step of adsorption and a step of photocatalytic oxidation under ultra-violet (365 nm), at 25 degreeC and atmospheric pressure. Both steps, adsorption and photocatalytic oxidation, have been investigated during four cycles. For both materials, the cumulated amounts adsorbed during four cycles corresponded to nearly twice the maximum adsorption capacities qmax proving the photocatalytic oxidation to regenerate the adsorbent. Concerning photocatalytic oxidation, the degree of mineralization was higher with the TiO2/AC composite: for each cycle, the value of the total organic carbon removal was 25% higher than that obtained with the mixture powder. These better photocatalytic performances involved better regeneration than higher adsorbed amounts for cycles 2, 3 and 4. Better performances with this promising material - TiO2 deposited onto AC - compared with TiO2 powder could be explained by the vicinity of photocatalytic and AC adsorption sites.

  16. Low Temperature Mechanical Testing of Carbon-Fiber/Epoxy-Resin Composite Materials

    Science.gov (United States)

    Nettles, Alan T.; Biss, Emily J.

    1996-01-01

    The use of cryogenic fuels (liquid oxygen and liquid hydrogen) in current space transportation vehicles, in combination with the proposed use of composite materials in such applications, requires an understanding of how such materials behave at cryogenic temperatures. In this investigation, tensile intralaminar shear tests were performed at room, dry ice, and liquid nitrogen temperatures to evaluate the effect of temperature on the mechanical response of the IM7/8551-7 carbon-fiber/epoxy-resin system. Quasi-isotropic lay-ups were also tested to represent a more realistic lay-up. It was found that the matrix became both increasingly resistant to microcracking and stiffer with decreasing temperature. A marginal increase in matrix shear strength with decreasing temperature was also observed. Temperature did not appear to affect the integrity of the fiber-matrix bond.

  17. Investigation of Structure and Physico-Mechanical Properties of Composite Materials Based on Copper - Carbon Nanoparticles Powder Systems

    Directory of Open Access Journals (Sweden)

    Kovtun V.

    2015-04-01

    Full Text Available Physico-mechanical and structural properties of electrocontact sintered copper matrix- carbon nanoparticles composite powder materials are presented. Scanning electron microscopy revealed the influence of preliminary mechanical activation of the powder system on distribution of carbon nanoparticles in the metal matrix. Mechanical activation ensures mechanical bonding of nanoparticles to the surface of metal particles, thus giving a possibility for manufacture of a composite with high physico-mechanical properties.

  18. Properties of Two Carbon Composite Materials Using LTM25 Epoxy Resin

    Science.gov (United States)

    Cruz, Juan R.; Shah, C. H.; Postyn, A. S.

    1996-01-01

    In this report, the properties of two carbon-epoxy prepreg materials are presented. The epoxy resin used in these two materials can yield lower manufacturing costs due to its low initial cure temperature, and the capability of being cured using vacuum pressure only. The two materials selected for this study are MR50/LTM25, and CFS003/LTM25 with Amoco T300 fiber; both prepregs are manufactured by The Advanced Composites Group. MR50/LTM25 is a unidirectional prepreg tape using Mitsubishi MR50 carbon fiber impregnated with LTM25 epoxy resin. CRS003/LTM25 is a 2 by 2 twill fabric using Amoco T300 fiber and impregnated with LTM25 epoxy resin. Among the properties presented in this report are strength, stiffness, bolt bearing, and damage tolerance. Many of these properties were obtained at three environmental conditions: cold temperature/dry (CTD), room temperature/dry (RTD), and elevated temperature/wet (ETW). A few properties were obtained at room temperature/wet (RTW), and elevated temperature/dry (ETD). The cold and elevated temperatures used for testing were -125 F and 180 F, respectively. In addition, several properties related to processing are presented.

  19. Macroscopic Crosslinked Neat Carbon Nanotube Materials and CNT/Carbon Fiber Hybrid Composites: Supermolecular Structure and New Failure Mode Study

    Science.gov (United States)

    2015-10-01

    bubbles in carbon fiber layers were not able to be expelled, resulting in a high void content. In contrast to the CF layers, SEM examination indicated... Reinforcement on the Processing and the Mechanical Behaviour of Carbon Fiber/epoxy Composites. Carbon 2009, 47 (12), 2914–2923. (135) Kharisov, B. I...50  4.4 Permeability  Results

  20. Dissolved organic matter composition of Arctic rivers: Linking permafrost and parent material to riverine carbon

    Science.gov (United States)

    O'Donnell, Jonathan A.; Aiken, George R.; Swanson, David K.; Panda, Santosh; Butler, Kenna D.; Baltensperger, Andrew P.

    2016-12-01

    Recent climate change in the Arctic is driving permafrost thaw, which has important implications for regional hydrology and global carbon dynamics. Permafrost is an important control on groundwater dynamics and the amount and chemical composition of dissolved organic matter (DOM) transported by high-latitude rivers. The consequences of permafrost thaw for riverine DOM dynamics will likely vary across space and time, due in part to spatial variation in ecosystem properties in Arctic watersheds. Here we examined watershed controls on DOM composition in 69 streams and rivers draining heterogeneous landscapes across a broad region of Arctic Alaska. We characterized DOM using bulk dissolved organic carbon (DOC) concentration, optical properties, and chemical fractionation and classified watersheds based on permafrost characteristics (mapping of parent material and ground ice content, modeling of thermal state) and ecotypes. Parent material and ground ice content significantly affected the amount and composition of DOM. DOC concentrations were higher in watersheds underlain by fine-grained loess compared to watersheds underlain by coarse-grained sand or shallow bedrock. DOC concentration was also higher in rivers draining ice-rich landscapes compared to rivers draining ice-poor landscapes. Similarly, specific ultraviolet absorbance (SUVA254, an index of DOM aromaticity) values were highest in watersheds underlain by fine-grained deposits or ice-rich permafrost. We also observed differences in hydrophobic organic acids, hydrophilic compounds, and DOM fluorescence across watersheds. Both DOC concentration and SUVA254 were negatively correlated with watershed active layer thickness, as determined by high-resolution permafrost modeling. Together, these findings highlight how spatial variations in permafrost physical and thermal properties can influence riverine DOM.

  1. Use of magnetic carbon composites from renewable resource materials for oil spill clean up and recovery

    Energy Technology Data Exchange (ETDEWEB)

    Viswanathan, Tito

    2015-10-27

    A method of separating a liquid hydrocarbon material from a body of water, includes: (a) mixing magnetic carbon-metal nanocomposites with a liquid hydrocarbon material dispersed in a body of water to allow the magnetic carbon-metal nanocomposites each to be adhered by the liquid hydrocarbon material to form a mixture; (b) applying a magnetic force to the mixture to attract the magnetic carbon-metal nanocomposites each adhered by the liquid hydrocarbon material; and (c) removing the body of water from the magnetic carbon-metal nanocomposites each adhered by the liquid hydrocarbon material while maintaining the applied magnetic force. The magnetic carbon-metal nanocomposites is formed by subjecting one or more metal lignosulfonates or metal salts to microwave radiation, in presence of lignin/derivatives either in presence of alkali or a microwave absorbing material, for a period of time effective to allow the carbon-metal nanocomposites to be formed.

  2. Influence of Terahertz Waves on Unidirectional Carbon Fibers in CFRP Composite Materials

    Directory of Open Access Journals (Sweden)

    Kwang-Hee IM

    2014-12-01

    Full Text Available Terahertz time domain spectroscopy (THz TDS system based on the reflective and through-transmission modes was utilized. Influence of terahertz waves (T-ray on the fiber surface layups in the CFRP solid composites was studied. It was found that the value of electrical conductivity in the carbon fibers varies by the layup directions of carbon fibers based on E-field (Electrical field. T-ray optimized scanning data could be obtained at the 90° angle normal to the E-field direction. GFRP (Glass-fiber reinforced plastics composite laminates were scanned with two saw cuts using a T-ray THz TDS system and the terahertz optimized scanning images were obtained at the angles normal to the E-field direction on the nonconducting materials. Also, by use of 2-dimensional spatial Fourier transform, interface C-scan images were transformed into quantitative angular distribution plots in order to show the fiber orientation information therein and to make the orientation of the ply predictable. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6440

  3. The influence of carbon fibre content on the tribological properties of polyarylate based composites materials

    Institute of Scientific and Technical Information of China (English)

    Burya; A.I.; Chigvintseva; O.P

    2001-01-01

    The analysis of scientific-technical literature has shown the prospectiveness of applyinghigh-temperature thermoplastic polymers - among which there are complex aromatic polyesters -as constructive materials. Mixed polyarylates of DV mark based on diphenilolpropane and themixture of iso- and terephtale acid are mentioned to make the most valuable practical interest. Forimproving technological and exploitation properties the authors of the article have suggested toreinforce the polymer linking element with uglen-9 mark. Combination of the composition compo-nents was realized within the rotating electromagnetic field with the help of non-equiaxial ferro-magnetic elements. The study of tribotechnical characteristics (coefficient of friction, intensity oflinear wear, temperature in the contact zone "polymer specimen - counterbody" of elaborated car-bon plastics) has been made at the disc machine of friction. Investigation of exploitation regimes’(specific pressure and slip velocity) influence on the mentioned properties of the initial polymer hasshown that polyarylate can be recommended for work at values of PV criterion not greater than 1.2MPa · m/s. Hardening the exploitation regimes is accompanied by the catastrophic wear of plastic.Reinforcement of polyarylate with carbon fibre is noted to enable significant improvement (to de-crease the coefficient of friction, to increase resistance to wear) of tribotechnical characteristics ofcarbon plastics. The most optimal is the content of carbon fibre in polyarylate in amount of 25mass.%.

  4. Preparation of carbon nanotube composite material with metal matrix by electroplating

    Institute of Scientific and Technical Information of China (English)

    AN Bai-gang; LI Li-xiang; Li Hong-xi

    2005-01-01

    It is demonstrated that the nickel can be deposited directly on the surface of carbon nanotubes without pre-sensitization by Sn2+ and Pd2+ in a watt bath containing suspended nanotubes by electroplating. The nickel is deposited as spherical nanoparticle on the nanotubes. By increasing reaction time, the carbon nanotube is fully coated with nickel. A probable model, which represents the formation process of carbon nanotube-nickel composites by electroplating, is presented. The results show that this method is efficient and simple for preparing carbon nanotube-metal composite.

  5. Extinction characterization of soot produced by laser ablating carbon fiber composite materials in air flow

    Science.gov (United States)

    Liu, Weiping; Ma, Zhiliang; Zhang, Zhenrong; Zhou, Menglian; Wei, Chenghua

    2015-05-01

    In order to research the dynamic process of energy coupling between an incident laser and a carbon fiber/epoxy resin composite material, an extinction characterization analysis of soot, which is produced by laser ablating and located in an air flow that is tangential to the surface of the composite material, is carried out. By the theory analyses, a relationship of mass extinction coefficient and extinction cross section of the soot is derived. It is obtained that the mass extinction coefficients of soot aggregates are the same as those of the primary particles when they contain only a few primary particles. This conclusion is significant when the soot is located in an air flow field, where the generations of the big soot aggregates are suppressed. A verification experiment is designed. The experiment employs Laser Induced Incandescence technology and laser extinction method for the soot synchronization diagnosis. It can derive a temporal curve of the mass extinction coefficient from the soot concentration and laser transmittance. The experiment results show that the mass extinction coefficient becomes smaller when the air flow velocity is higher. The reason is due to the decrease of the scatter effects of the soot particles. The experiment results agree with the theory analysis conclusion.

  6. Material characterization of several resin systems for high temperature carbon fiber reinforced composites

    Science.gov (United States)

    Yoon, Sung Ho; Oh, Jin Oh; Choi, Dong Hyun; Lee, Sang Woo

    2012-04-01

    Material characterization of several resin systems for high temperature carbon fiber reinforced composites was performed through a series of the tensile test, the dynamic mechanical analysis (DMA) test, and the strand test. The modified tensile specimens and the DMA specimens were used to evaluate the tensile and thermal analysis properties of resin systems. The strand specimens were used to evaluate the tensile properties and load transfer efficiencies of the specimens. Four types of resin systems were considered. One was a conventional resin system currently used for filament wound structures and other three were high temperature resin systems. According to the tensile and DMA test results, the tensile modulus decreases slightly and the tensile strength decreases rapidly until the temperature reaches glass transition temperature. The tensile modulus and tensile strength are almost negligible above glass transition temperature. The tensile modulus obtained from the tensile test is consistent with that from the DMA test at different temperatures. From the strand test results, considering, the load transfer efficiency is found to be around 87 to 90 % of the tensile strength of T800H-12K carbon fibers for all resin systems except the specimen with the Type 2. Finally we found that the Type 4 is the best candidate for high temperature resin system applicable to filament wound structures in the view of the glass transition temperature as well as the tensile properties.

  7. Liquid Phase Plasma Synthesis of Iron Oxide/Carbon Composite as Dielectric Material for Capacitor

    Directory of Open Access Journals (Sweden)

    Heon Lee

    2014-01-01

    Full Text Available Iron oxide/carbon composite was synthesized using a liquid phase plasma process to be used as the electrode of supercapacitor. Spherical iron oxide nanoparticles with the size of 5~10 nm were dispersed uniformly on carbon powder surface. The specific capacitance of the composite increased with increasing quantity of iron oxide precipitate on the carbon powder up to a certain quantity. When the quantity of the iron oxide precipitate exceeds the threshold, however, the specific capacitance was rather reduced by the addition of precipitate. The iron oxide/carbon composite containing an optimum quantity (0.33 atomic % of iron oxide precipitate exhibited the smallest resistance and the largest initial resistance slope.

  8. Nanostructured TiO2-coated activated carbon composite as an electrode material for asymmetric hybrid capacitors.

    Science.gov (United States)

    Kim, Sang-Ok; Lee, Joong Kee

    2012-02-01

    A nanostructured TiO2-coated activated carbon (TAC) composite was synthesized by a modified sol-gel reaction and employed it as a negative electrode active material for an asymmetric hybrid capacitor. The structural characterization showed that the TiO2 nano-layer was deposited on the surface of the activated carbon and the TAC composite has a highly mesoporous structure. The evaluation of electrochemical characteristics of the TAC electrode was carried out by galvanostatic charge/discharge cycling tests and electrochemical impedance spectroscopy. The obtained specific capacitance of the TAC composite was 42.87 F/g, which showed by 27.1% higher than that of the activated carbon (AC). The TAC composite also exhibited an excellent cycle performance and kept 95% of initial capacitance over 500 cycles.

  9. Impedance spectroscopic analysis of composite electrode from activated carbon/conductive materials/ruthenium oxide for supercapacitor applications

    Energy Technology Data Exchange (ETDEWEB)

    Taer, E.; Awitdrus,; Farma, R. [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Department of Physics, Faculty of Mathematics and Natural Sciences, University of Riau, 28293 Pekanbaru, Riau (Indonesia); Deraman, M., E-mail: madra@ukm.my; Talib, I. A.; Ishak, M. M.; Omar, R.; Dolah, B. N. M.; Basri, N. H.; Othman, M. A. R. [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Kanwal, S. [ICCBS, H.E.J. Research Institute of Chemistry, University of Karachi, 75270 Karachi (Pakistan)

    2015-04-16

    Activated carbon powders (ACP) were produced from the KOH treated pre-carbonized rubber wood sawdust. Different conductive materials (graphite, carbon black and carbon nanotubes (CNTs)) were added with a binder (polivinylidene fluoride (PVDF)) into ACP to improve the supercapacitive performance of the activated carbon (AC) electrodes. Symmetric supercapacitor cells, fabricated using these AC electrodes and 1 molar H{sub 2}SO{sub 4} electrolyte, were analyzed using a standard electrochemical impedance spectroscopy technique. The addition of graphite, carbon black and CNTs was found effective in reducing the cell resistance from 165 to 68, 23 and 49 Ohm respectively, and increasing the specific capacitance of the AC electrodes from 3 to 7, 17, 32 F g{sup −1} respectively. Since the addition of CNTs can produce the highest specific capacitance, CNTs were chosen as a conductive material to produce AC composite electrodes that were added with 2.5 %, 5 % and 10 % (by weight) electro-active material namely ruthenium oxide; PVDF binder and CNTs contents were kept at 5 % by weight in each AC composite produced. The highest specific capacitance of the cells obtained in this study was 86 F g{sup −1}, i.e. for the cell with the resistance of 15 Ohm and composite electrode consists of 5 % ruthenium oxide.

  10. Composite materials based on poly(trimethylene carbonate) and beta-tricalcium phosphate for orbital floor and wall reconstruction

    NARCIS (Netherlands)

    van Leeuwen, Anne C.; Bos, Rudolf R. M.; Grijpma, Dirk W.

    2012-01-01

    Poly(trimethylene carbonate) and beta-tricalcium phosphate (PTMC/beta-TCP) composite materials were prepared by coprecipitation and compression molding. The effect of different amounts of the ceramic component (15 and 30 vol %) on the properties was investigated. The effect of lamination with minima

  11. Interconnected sandwich structure carbon/Si-SiO2/carbon nanospheres composite as high performance anode material for lithium-ion batteries

    Institute of Scientific and Technical Information of China (English)

    Yuanjin Du; Mengyan Hou; Dandan Zhou; Yonggang Wang; Congxiao Wang; Yongyao Xia

    2014-01-01

    In the present work, an interconnected sandwich carbon/Si-SiO2/carbon nanospheres composite was prepared by template method and carbon thermal vapor deposition (TVD). The carbon conductive layer can not only efficiently improve the electronic conductivity of Si-based anode, but also play a key role in alleviating the negative effect from huge volume expansion over discharge/charge of Si-based anode. The resulting material delivered a reversible capacity of 1094 mAh/g, and exhibited excellent cycling stability. It kept a reversible capacity of 1050 mAh/g over 200 cycles with a capacity retention of 96%.

  12. Use of magnetic carbon composites from renewable resource materials for oil spill clean up and recovery

    Science.gov (United States)

    Viswanathan, Tito

    2014-02-11

    A method for separating a liquid hydrocarbon material from a body of water. In one embodiment, the method includes the steps of mixing a plurality of magnetic carbon-metal nanocomposites with a liquid hydrocarbon material dispersed in a body of water to allow the plurality of magnetic carbon-metal nanocomposites each to be adhered by an amount of the liquid hydrocarbon material to form a mixture, applying a magnetic force to the mixture to attract the plurality of magnetic carbon-metal nanocomposites each adhered by an amount of the liquid hydrocarbon material, and removing said plurality of magnetic carbon-metal nanocomposites each adhered by an amount of the liquid hydrocarbon material from said body of water while maintaining the applied magnetic force, wherein the plurality of magnetic carbon-metal nanocomposites is formed by subjecting one or more metal lignosulfonates or metal salts to microwave radiation, in presence of lignin/derivatives either in presence of alkali or a microwave absorbing material.

  13. Hollow spherical carbonized polypyrrole/sulfur composite cathode materials for lithium/sulfur cells with long cycle life

    Science.gov (United States)

    Wang, Zhongbao; Zhang, Shichao; Zhang, Lan; Lin, Ruoxu; Wu, Xiaomeng; Fang, Hua; Ren, Yanbiao

    2014-02-01

    Hollow carbonized polypyrrole (PPy) spheres are synthesized using poly(methyl methacrylate-ethyl acrylate-acrylic acid) latex spheres as sacrificial templates. The hollow spherical carbonized PPy/sulfur composite cathode materials are prepared by heating the mixture of hollow carbonized PPy spheres and element sulfur at 155 °C for 24 h. Scanning electron microscope (SEM) and transmission electron microscope (TEM) observations show the hollow structures of the carbonized PPy spheres and the homogeneous distribution of sulfur on the carbonized PPy shells. The hollow spherical carbonized PPy/sulfur composite with 60.9 wt.% S shows high specific capacity and excellent cycling stability when used as the cathode materials in lithium/sulfur cells, whose initial specific discharge capacity reaches as high as 1320 mA h g-1 and the reversible discharge capacity retains 758 mA h g-1 after 400 cycles at 0.2C. The excellent electrochemical properties benefit from the hollow structures and the flexible shells of the carbonized PPy spheres.

  14. Carbon-coated Ni 20Si 80 alloy-graphite composite as an anode material for lithium-ion batteries

    Science.gov (United States)

    Lee, Heon-Yong; Kim, Young-Lae; Hong, Moon-Ki; Lee, Sung-Man

    A carbon-coated Ni 20Si 80 alloy-graphite composite has been studied as the anode for lithium-ion batteries. The composite is prepared by simple heat-treatment of a mixture of coal tar pitch and a Ni 20Si 80-graphite composite at 900 °C and under argon. The Ni 20Si 80 alloy powders are synthesized by mechanical alloying. The composite demonstrates promising electrochemical properties such as high reversible capacity, excellent cycle performance, and sufficiently high initial charge-discharge coulombic efficiency. This suggests buffering and conductive actions on the main active material, viz., Ni 20Si 80 alloy, of the graphite. These two effects are strongly enhanced by the carbon coating treatment.

  15. Polysulphone composite membranes modified with two types of carbon additives as a potential material for bone tissue regeneration

    Indian Academy of Sciences (India)

    ALICJA WEDEL-GRZENDA; ANETA FRACZEK-SZCZYPTA; MAURICIO TERRONES; ANA LAURA ELÍAS; MALGORZATA LEKKA; ELZBIETA MENASZEK; STANISLAW BLAZEWICZ

    2017-02-01

    This study presents a detailed evaluation of the impact of carbon fibrous materials on the physicochemical properties of polysulphone (PSU) membranes and their preliminary osteoblast-like cells response in vitro. Multiwalled carbon nanotubes (MWCNTs) and short carbon fibres (SCFs) were incorporated into PSU and membranes were produced by the phase inversion method. Then, the physicochemical properties of the membranes’ surface were investigated. Scanning electron microscopy (SEM) was used to evaluate microstructure and porosity. Surface properties such as roughness, wettability and surface energy were evaluated using atomic force microscopy (AFM), contact profilometry and a goniometer, respectively. The presence of carbon fibrous additives in the PSU matrix improved its hydrophilicity. Porosity and topography of the PSU membranes were also changed upon incorporation of carbon additives. The mechanical properties of the PSU membranes were improved after SCF addition. All physicochemical properties of the obtained composite membranes had significant impact on the osteoblast-like cells response. Preliminary viability tests indicated biocompatibility of all membranes.

  16. Mechanical and Vibration Testing of Carbon Fiber Composite Material with Embedded Piezoelectric Sensors

    Science.gov (United States)

    Duffy, Kirsten P.; Lerch, Bradley A.; Wilmoth, Nathan G.; Kray, Nicholas; Gemeinhardt, Gregory

    2012-01-01

    Piezoelectric materials have been proposed as a means of decreasing turbomachinery blade vibration either through a passive damping scheme, or as part of an active vibration control system. For polymer matrix fiber composite (PMFC) blades, the piezoelectric elements could be embedded within the blade material, protecting the brittle piezoceramic material from the airflow and from debris. Before implementation of a piezoelectric element within a PMFC blade, the effect on PMFC mechanical properties needs to be understood. This study attempts to determine how the inclusion of a packaged piezoelectric patch affects the material properties of the PMFC. Composite specimens with embedded piezoelectric patches were tested in four-point bending, short beam shear, and flatwise tension configurations. Results show that the embedded piezoelectric material does decrease the strength of the composite material, especially in flatwise tension, attributable to failure at the interface or within the piezoelectric element itself. In addition, the sensing properties of the post-cured embedded piezoelectric materials were tested, and performed as expected. The piezoelectric materials include a non-flexible patch incorporating solid piezoceramic material, and two flexible patch types incorporating piezoelectric fibers. The piezoceramic material used in these patches was Navy Type-II PZT.

  17. Micromechanics model for predicting anisotropic electrical conductivity of carbon fiber composite materials

    Science.gov (United States)

    Haider, Mohammad Faisal; Haider, Md. Mushfique; Yasmeen, Farzana

    2016-07-01

    Heterogeneous materials, such as composites consist of clearly distinguishable constituents (or phases) that show different electrical properties. Multifunctional composites have anisotropic electrical properties that can be tailored for a particular application. The effective anisotropic electrical conductivity of composites is strongly affected by many parameters including volume fractions, distributions, and orientations of constituents. Given the electrical properties of the constituents, one important goal of micromechanics of materials consists of predicting electrical response of the heterogeneous material on the basis of the geometries and properties of the individual phases, a task known as homogenization. The benefit of homogenization is that the behavior of a heterogeneous material can be determined without resorting or testing it. Furthermore, continuum micromechanics can predict the full multi-axial properties and responses of inhomogeneous materials, which are anisotropic in nature. Effective electrical conductivity estimation is performed by using classical micromechanics techniques (composite cylinder assemblage method) that investigates the effect of the fiber/matrix electrical properties and their volume fractions on the micro scale composite response. The composite cylinder assemblage method (CCM) is an analytical theory that is based on the assumption that composites are in a state of periodic structure. The CCM was developed to extend capabilities variable fiber shape/array availability with same volume fraction, interphase analysis, etc. The CCM is a continuum-based micromechanics model that provides closed form expressions for upper level length scales such as macro-scale composite responses in terms of the properties, shapes, orientations and constituent distributions at lower length levels such as the micro-scale.

  18. Hybrid nanostructured microporous carbon-mesoporous carbon doped titanium dioxide/sulfur composite positive electrode materials for rechargeable lithium-sulfur batteries

    Science.gov (United States)

    Zegeye, Tilahun Awoke; Kuo, Chung-Feng Jeffrey; Wotango, Aselefech Sorsa; Pan, Chun-Jern; Chen, Hung-Ming; Haregewoin, Atetegeb Meazah; Cheng, Ju-Hsiang; Su, Wei-Nien; Hwang, Bing-Joe

    2016-08-01

    Herein, we design hybrid nanostructured microporous carbon-mesoporous carbon doped titanium dioxide/sulfur composite (MC-Meso C-doped TiO2/S) as a positive electrode material for lithium-sulfur batteries. The hybrid MC-Meso C-doped TiO2 host material is produced by a low-cost, hydrothermal and annealing process. The resulting conductive material shows dual microporous and mesoporous behavior which enhances the effective trapping of sulfur and polysulfides. The hybrid MC-Meso C-doped TiO2/S composite material possesses rutile TiO2 nanotube structure with successful carbon doping while sulfur is uniformly distributed in the hybrid MC-Meso C-doped TiO2 composite materials after the melt-infusion process. The electrochemical measurement of the hybrid material also shows improved cycle stability and rate performance with high sulfur loading (61.04%). The material delivers an initial discharge capacity of 802 mAh g-1 and maintains it at 578 mAh g-1 with a columbic efficiency greater than 97.1% after 140 cycles at 0.1 C. This improvement is thought to be attributed to the unique hybrid nanostructure of the MC-Meso C-doped TiO2 host and the good dispersion of sulfur in the narrow pores of the MC spheres and the mesoporous C-doped TiO2 support.

  19. The Investigation on the Potential of Coconut Shell Powder Composite in Term of Carbon Composition, Surface Porosity and Dielectric Properties as a Microwave Absorbing Material

    Directory of Open Access Journals (Sweden)

    Yew Been Seok

    2016-01-01

    Full Text Available Agricultural wastes are renewable resources that are potentially useful as microwave absorbing materials. This paper presents the investigation on the carbon composition, surface porosity of the raw coconut shell powder particles and the dielectric properties of coconut shell powder with epoxy resin matrix composites. From CHNS elemental analysis, it was found that the carbon composition of coconut shell powder is 46.700%. Presences of macropores (≈ 2μm were detected in the SEM analysis of the coconut shell powder particles. Measurement on dielectric properties of the coconut shell powder composites was performed by using open-ended coaxial probe method over microwave frequency range of 1-8 GHz. The overall dielectric constant (εr’ and dielectric loss factor (εr” of the composite with ratio 50:50 were 3.56 and 0.26, ranging from 3.35-3.76 and 0.21-0.30 respectively; whereas for composite ratio 40:60, the overall dielectric constant (εr’ and dielectric loss factor (εr” were 2.97 and 0.21, ranging from 2.74-3.17 and 0.16-0.27 respectively. The electrical conductivity calculated based on measured εr” was 0.067 and 0.054 for composite ratio 50:50 and 40:60 respectively. The dielectric properties and electrical conductivity of the coconut shell powder composites were influenced by the greater presence of high dielectric material (coconut shell powder. This experimental investigation on the potential of the coconut shell powder with epoxy resin composites indicates that the ability of the composite to absorb and convert microwave signals is dependent on the carbonaceous materials of the composite. This result offers a great opportunity to diversify the use of coconut shell powder as microwave absorbing material.

  20. Cyclophosphazene based conductive polymer-carbon nanotube composite as novel supporting material for methanol fuel cell applications.

    Science.gov (United States)

    Prasanna, Dakshinamoorthy; Selvaraj, Vaithilingam

    2016-06-15

    This present study reports the development of novel catalyst support of amine terminated cyclophosphazene/cyclophosphazene/hexafluoroisopropylidenedianiline-carbon nanotube (ATCP/CP/HFPA-CNT) composite. The ATCP/CP/HFPA-CNT composite has been used as a catalyst support for platinum (Pt) and platinum-gold (Pt-Au) nanoparticles towards electrooxidation of methanol in alkaline medium. The obtained anode materials were characterized by X-ray diffraction, transmission electron microscope and energy dispersive X-ray analysis. Electrocatalytic performances of Pt/ATCP/CP/HFPA-CNT and Pt-Au/ATCP/CP/HFPA-CNT catalysts were investigated by cyclic voltammetry, CO stripping and chronoamperometric techniques. The electrooxidation of methanol and CO stripping results conclude that the metal nanocatalyst embedded with ATCP/CP/HFPA-CNT composite shows significantly higher anodic oxidation current, more CO tolerance and lower onset potential when compared to that of the Pt/CNT and Pt/C (Vulcan carbon) catalysts.

  1. Microwave Absorption and Shielding, Property of Composites with FeSiA1 and Carbonous Materials as Filler

    Institute of Scientific and Technical Information of China (English)

    Wenqiang Zhang; Yonggang Xu; Liming Yuan; Jun Cai; Deyuan Zhangt

    2012-01-01

    Silicone rubber composites filled with FeSiAI alloys and multi-walled carbon nanotubes (MWCNT)/graphite have been prepared for the first time by a coating process. The complex permittivity and permeability of the composites were measured with a vector network analyzer in a 1-4 GHz frequency range, and the DC electric conductivity was measured by a standard four-point contact method. These parameters were then used to calculate the reflection loss (RL) and shielding effectiveness (SE) of the composites. The results showed that the added MWCNT increased the permittivity and permeability of composites in the L-band, while the added graphite increased only the permittivity. The variation lies in the interactions between two carbonous absorbents. Addition of 1 wt% MWCNT enhanced the RL in the L-band (minimum -5.7 dB at 1 ram, -7.3 dB at 1.5 ram), while the addition of graphite did not. Addition of MWCNT as well as graphite reinforced the shielding property of the composites (maximum SE 13.3 dB at 1 ram, 18.3 dB at 1.5 ram) owing to the increase of conductivity. The addition of these carbonous materials could hold the promise of enforcing the absorption and shielding property of the absorbers.

  2. Mesoporous carbon materials

    Science.gov (United States)

    Dai, Sheng; Fulvio, Pasquale Fernando; Mayes, Richard T.; Wang, Xiqing; Sun, Xiao-Guang; Guo, Bingkun

    2014-09-09

    A conductive mesoporous carbon composite comprising conductive carbon nanoparticles contained within a mesoporous carbon matrix, wherein the conductive mesoporous carbon composite possesses at least a portion of mesopores having a pore size of at least 10 nm and up to 50 nm, and wherein the mesopores are either within the mesoporous carbon matrix, or are spacings delineated by surfaces of said conductive carbon nanoparticles when said conductive carbon nanoparticles are fused with each other, or both. Methods for producing the above-described composite, devices incorporating them (e.g., lithium batteries), and methods of using them, are also described.

  3. Preparation and electrochemical characterization of polyaniline/activated carbon composites as an electrode material for supercapacitors.

    Science.gov (United States)

    Oh, Misoon; Kim, Seok

    2012-01-01

    Polyaniline (PANI)/activated carbon (AC) composites were prepared by a chemical oxidation polymerization. To find an optimum ratio between PANI and AC which shows superior electrochemical properties, the preparation was carried out in changing the amount of added aniline monomers. The morphology of prepared composites was investigated by scanning electron microscopy (SEM) and transmission electron microscope (TEM). The structural and thermal properties were investigated by Fourier transform infrared spectra (FT-IR) and thermal gravimetric analysis (TGA), respectively. The electrochemical properties were characterized by cyclic voltammetry (CV). Composites showed a summation of capacitances that consisted of two origins. One is double-layer capacitance by ACs and the other is faradic capacitance by redox reaction of PANI. Fiber-like PANIs are coated on the surface of ACs and they contribute to the large surface for redox reaction. The vacancy among fibers provided the better diffusion and accessibility of ion. High capacitances of composites were originated from the network structure having vacancy made by PANI fibers. It was found that the composite prepared with 5 ml of aniline monomer and 0.25 g of AC showed the highest capacitance. Capacitance of 771 F/g was obtained at a scan rate of 5 mV/s.

  4. Thermo-mechanical characterisation of low density carbon foams and composite materials for the ATLAS upgrade

    CERN Document Server

    Isaac, Bonad

    As a result of the need to increase the luminosity of the Large Hadron Collider (LHC) at CERN-Geneva by 2020, the ATLAS detector requires an upgraded inner tracker. Up- grading the ATLAS experiment is essential due to higher radiation levels and high particle occupancies. The design of this improved inner tracker detector involves development of silicon sensors and their support structures. These support structures need to have well un- derstood thermal properties and be dimensionally stable in order to allow efficient cooling of the silicon and accurate track reconstruction. The work presented in this thesis is an in- vestigation which aims to qualitatively characterise the thermal and mechanical properties of the materials involved in the design of the inner tracker of the ATLAS upgrade. These materials are silicon carbide foam (SiC foam), low density carbon foams such as PocoFoam and Allcomp foam, Thermal Pyrolytic Graphite (TPG), carbon/carbon and Carbon Fibre Re- inforced Polymer (CFRP). The work involve...

  5. LiFePO4 - 3D carbon nanofiber composites as cathode materials for Li-ions batteries

    Science.gov (United States)

    Dimesso, L.; Spanheimer, C.; Jaegermann, W.; Zhang, Y.; Yarin, A. L.

    2012-03-01

    The characterization of carbon nanofiber 3D nonwovens, prepared by electrospinning process, coated with olivine structured lithium iron phosphate is reported. The LiFePO4 as cathode material for lithium ion batteries was prepared by a Pechini-assisted reversed polyol process. The coating has been successfully performed on carbon nanofiber 3D nonwovens by soaking in aqueous solution containing lithium, iron salts and phosphates at 70 °C for 2-4 h. After drying-out, the composites were annealed at 600 °C for 5 h under nitrogen. The surface investigation of the prepared composites showed a uniform coating of the carbon nonwoven nanofibers as well as the formation of cauliflower-like crystalline structures which are uniformly distributed all over the surface area of the carbon nanofibers. The electrochemical measurements on the composites showed good performances delivering a discharge specific capacity of 156 mAhg- 1 at a discharging rate of C/25 and 152 mAhg- 1 at a discharging rate of C/10 at room temperature.

  6. Synthesis of LiFePO_4/C Composite Cathode Materials Using High Surface Area Carbon as Carbon Sources

    Institute of Scientific and Technical Information of China (English)

    George; Ting-kuo; Fey; Kai-Lun; Chiang

    2007-01-01

    1 Results The pyrolyzed product of peanut shells was utilized as a carbon source to synthesize a LiFePO4/C composite.The advantages of using agricultural wastes such as peanut shells are low costs,easy processing,and environmentally benigness.Peanut shell was first treated with a porogenic agent to produce a precursor with high porosity and surface area (>2 000 m2·g-1).A small amount of precursor was mixed with LiFePO4 fine powders and heated.The optimum calcination process for synthesizing LiFePO4/C co...

  7. Carbon/PEEK composite materials as an alternative for stainless steel/titanium hip prosthesis: a finite element study.

    Science.gov (United States)

    Rezaei, Farshid; Hassani, Kamran; Solhjoei, Nosratollah; Karimi, Alireza

    2015-12-01

    Total hip replacement (THR) has been ranked within the most typical surgical processes in the world. The durability of the prosthesis and loosening of prosthesis are the main concerns that mostly reported after THR surgeries. In THR, the femoral prosthesis can be fixed by either cement or cementless methods in the patient's bones. In both procedures, the stability of the prosthesis in the hosted bone has a key asset in its long-term durability and performance. This study aimed to execute a comparative finite element simulation to assess the load transfer between the prosthesis, which is made of carbon/PEEK composite and stainless steel/titanium, and the femur bone. The mechanical behavior of the cortical bone was assumed as a linear transverse isotropic while the spongy bone was modeled like a linear isotropic material. The implants were made of stainless steel (316L) and titanium alloy as they are common materials for implants. The results showed that the carbon/PEEK composites provide a flatter load transfer from the upper body to the leg compared to the stainless steel/titanium prosthesis. Furthermore, the results showed that the von Mises stress, principal stress, and the strain in the carbon/PEEK composites prosthesis were significantly lower than that made of the stainless steel/titanium. The results also imply that the carbon/PEEK composites can be applied to introduce a new optimum design for femoral prosthesis with adjustable stiffness, which can decrease the stress shielding and interface stress. These findings will help clinicians and biomedical experts to increase their knowledge about the hip replacement.

  8. One-pot synthesis of tin-borophosphate-carbon composites as anode materials for Li-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Mouyane, Mohamed [Institut Charles Gerhardt, UMR 5253 CNRS, Université de Montpellier, CC 1502, 34095 Montpellier Cedex 5 (France); LUSAC (EA 4253), Université de Caen Basse Normandie, 50130 Cherbourg-Octeville (France); Jumas, Jean-Claude; Olivier-Fourcade, Josette [Institut Charles Gerhardt, UMR 5253 CNRS, Université de Montpellier, CC 1502, 34095 Montpellier Cedex 5 (France); Cassaignon, Sophie [UPMC (UMR7574 CNRS), Chimie de la Matière Condensée de Paris (France); Collège de France, 11 place Marcelin Berthelot, 75231 Paris Cedex 05 (France); Jordy, Christian [SAFT, Direction de la Recherche, 111–113 Bd Alfred Daney, 33074 Bordeaux (France); Lippens, Pierre-Emmanuel, E-mail: lippens@univ-montp2.fr [Institut Charles Gerhardt, UMR 5253 CNRS, Université de Montpellier, CC 1502, 34095 Montpellier Cedex 5 (France)

    2016-01-15

    Sn{sub x}(Ca{sub 0.05}B{sub 0.975}P{sub 0.975}O{sub 3.95}){sub 1−x}/C composites as anode material for Li-ion batteries, with x=0.83 and x=0.71 were synthesized by a facile route including cellulose as carbon source. The composites were characterized by X-ray diffraction, scanning electron microscopy, Raman spectroscopy and {sup 119}Sn Mössbauer spectroscopy. In the latter case, different tin phases were found in the composite including the Sn{sup II}-based amorphous interface between metallic tin and borophosphate particles that improves the dispersion of the active species. The best electrochemical performances were obtained for x=0.71 that were further improved by ball-milled the composite with a small amount of carbon black. - Graphical abstract: {sup 119}Sn Mössbauer spectra of Sn{sub x}(Ca{sub 0.05}B{sub 0.975}P{sub 0.975}O{sub 3.95}){sub 1−x}/C composites with x=0.83 (a) and x=0.71 (b).

  9. Carbon nanostructure composite for electromagnetic interference shielding

    Indian Academy of Sciences (India)

    Anupama Joshi; Suwarna Datar

    2015-06-01

    This communication reviews current developments in carbon nanostructure-based composite materials for electromagnetic interference (EMI) shielding. With more and more electronic gadgets being used at different frequencies, there is a need for shielding them from one another to avoid interference. Conventionally, metal-based shielding materials have been used. But due to the requirement of light weight, corrosion resistive materials, lot of work is being done on composite materials. In this research the forerunner is the nanocarbon-based composite material whose different forms add different characteristics to the composite. The article focusses on composites based on graphene, graphene oxide, carbon nanotubes, and several other novel forms of carbon.

  10. In vitro degradation and cell response of calcium carbonate composite ceramic in comparison with other synthetic bone substitute materials

    Energy Technology Data Exchange (ETDEWEB)

    He, Fupo [Department of Biomedical Engineering, School of Basic Sciences, Guangzhou Medical University, Guangzhou 510182 (China); Zhang, Jing [School of Materials Science and Engineering, South China University of Technology, Guangzhou 510641 (China); Yang, Fanwen; Zhu, Jixiang; Tian, Xiumei [Department of Biomedical Engineering, School of Basic Sciences, Guangzhou Medical University, Guangzhou 510182 (China); Chen, Xiaoming, E-mail: xmchenw@126.com [Department of Biomedical Engineering, School of Basic Sciences, Guangzhou Medical University, Guangzhou 510182 (China)

    2015-05-01

    The robust calcium carbonate composite ceramics (CC/PG) can be acquired by fast sintering calcium carbonate at a low temperature (650 °C) using a biocompatible, degradable phosphate-based glass (PG) as sintering agent. In the present study, the in vitro degradation and cell response of CC/PG were assessed and compared with 4 synthetic bone substitute materials, calcium carbonate ceramic (CC), PG, hydroxyapatite (HA) and β-tricalcium phosphate (β-TCP) ceramics. The degradation rates in decreasing order were as follows: PG, CC, CC/PG, β-TCP, and HA. The proliferation of rat bone mesenchymal stem cells (rMSCs) cultured on the CC/PG was comparable with that on CC and PG, but inferior to HA and β-TCP. The alkaline phosphatase (ALP) activity of rMSCs on CC/PG was lower than PG, comparable with β-TCP, but higher than HA. The rMSCs on CC/PG and PG had enhanced gene expression in specific osteogenic markers, respectively. Compared to HA and β-TCP, the rMSCs on the CC/PG expressed relatively lower level of collagen I and runt-related transcription factor 2, but showed more considerable expression of osteopontin. Although CC, PG, HA, and β-TCP possessed impressive performances in some specific aspects, they faced extant intrinsic drawbacks in either degradation rate or mechanical strength. Based on considerable compressive strength, moderate degradation rate, good cell response, and being free of obvious shortcoming, the CC/PG is promising as another choice for bone substitute materials. - Highlights: • A calcium carbonate composite ceramic (CC/PG) was acquired. • The in vitro degradation and cell response of CC/PG were compared to 4 materials. • The CC/PG showed moderate degradation rate. • The CC/PG exhibited good cell response. • The CC/PG was free of obvious drawback compared to other materials.

  11. The preparation and performance of calcium carbide-derived carbon/polyaniline composite electrode material for supercapacitors

    Science.gov (United States)

    Zheng, Liping; Wang, Ying; Wang, Xianyou; Li, Na; An, Hongfang; Chen, Huajie; Guo, Jia

    Calcium carbide (CaC 2)-derived carbon (CCDC)/polyaniline (PANI) composite materials are prepared by in situ chemical oxidation polymerization of an aniline solution containing well-dispersed CCDC. The structure and morphology of CCDC/PANI composite are characterized by Fourier infrared spectroscopy (FTIR), scanning electron microscope (SEM), transmission electron microscopy (TEM) and N 2 sorption isotherms. It has been found that PANI was uniformly deposited on the surface and the inner pores of CCDC. The supercapacitive behaviors of the CCDC/PANI composite materials are investigated with cyclic voltammetry (CV), galvanostatic charge/discharge and cycle life measurements. The results show that the CCDC/PANI composite electrodes have higher specific capacitances than the as grown CCDC electrodes and higher stability than the conducting polymers. The capacitance of CCDC/PANI composite electrode is as high as 713.4 F g -1 measured by cyclic voltammetry at 1 mV s -1. Besides, the capacitance retention of coin supercapacitor remained 80.1% after 1000 cycles.

  12. The preparation and performance of calcium carbide-derived carbon/polyaniline composite electrode material for supercapacitors

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Liping; Wang, Xianyou; Li, Na; An, Hongfang; Chen, Huajie [School of Chemistry, Key Laboratory of Environmentally Friendly Chemistry and Applications of Minister of Education, Xiangtan University, Hunan 411105 (China); Wang, Ying; Guo, Jia [School of Chemical Engineering and Pharmacy, Wuhan Institute of Technology, Hubei 430073 (China)

    2010-03-15

    Calcium carbide (CaC{sub 2})-derived carbon (CCDC)/polyaniline (PANI) composite materials are prepared by in situ chemical oxidation polymerization of an aniline solution containing well-dispersed CCDC. The structure and morphology of CCDC/PANI composite are characterized by Fourier infrared spectroscopy (FTIR), scanning electron microscope (SEM), transmission electron microscopy (TEM) and N{sub 2} sorption isotherms. It has been found that PANI was uniformly deposited on the surface and the inner pores of CCDC. The supercapacitive behaviors of the CCDC/PANI composite materials are investigated with cyclic voltammetry (CV), galvanostatic charge/discharge and cycle life measurements. The results show that the CCDC/PANI composite electrodes have higher specific capacitances than the as grown CCDC electrodes and higher stability than the conducting polymers. The capacitance of CCDC/PANI composite electrode is as high as 713.4 F g{sup -1} measured by cyclic voltammetry at 1 mV s{sup -1}. Besides, the capacitance retention of coin supercapacitor remained 80.1% after 1000 cycles. (author)

  13. Carbonized asphaltene-based carbon-carbon fiber composites

    Energy Technology Data Exchange (ETDEWEB)

    Bohnert, George; Lula, James; Bowen, III, Daniel E.

    2016-12-27

    A method of making a carbon binder-reinforced carbon fiber composite is provided using carbonized asphaltenes as the carbon binder. Combinations of carbon fiber and asphaltenes are also provided, along with the resulting composites and articles of manufacture.

  14. Lithographically defined microporous carbon-composite structures

    Energy Technology Data Exchange (ETDEWEB)

    Burckel, David Bruce; Washburn, Cody M.; Lambert, Timothy N.; Finnegan, Patrick Sean; Wheeler, David R.

    2016-12-06

    A microporous carbon scaffold is produced by lithographically patterning a carbon-containing photoresist, followed by pyrolysis of the developed resist structure. Prior to exposure, the photoresist is loaded with a nanoparticulate material. After pyrolysis, the nanonparticulate material is dispersed in, and intimately mixed with, the carbonaceous material of the scaffold, thereby yielding a carbon composite structure.

  15. Advanced X-Ray Inspection of Reinforced Carbon Composite Materials on the Orbiter Leading Edge Structural Subsystem (LESS)

    Science.gov (United States)

    Hernandez, Jose M.; Berry, Robert F.; Osborn, Robin; Bueno, Clifford; Osterlitz, Mark; Mills, Richard; Morris, Philip; Phalen, Robert; McNab, Jim; Thibodeaux, Tahanie; Thompson, Kyle

    2004-01-01

    The post return-to-flight (RTF) inspection methodology for the Orbiter Leading Edge Structural Subsystem (LESS) is currently being defined. Numerous NDT modalities and techniques are being explored to perform the flight-to-flight inspections of the reinforced carbon/carbon (RCC) composite material for impact damage, general loss of mass in the bulk layers, or other anomalous conditions that would pose risk to safe return upon re-entry. It is possible to have an impact upon ascent that is not visually observable on the surface, yet causes internal damage. Radiographic testing may be a useful NDT technique for such occurrences. The authors have performed radiographic tests on full-sized mock samples of LESS hardware with embedded image quality phantoms. Digitized radiographic film, computed radiography and flat panel digital real-time radiography was acquired using a GE Eresco 200 x-ray tube, and Se-75 and Yb-169 radioisotopes.

  16. Nickel Sulfide/Graphene/Carbon Nanotube Composites as Electrode Material for the Supercapacitor Application in the Sea Flashing Signal System

    Institute of Scientific and Technical Information of China (English)

    Hailong Chen; Ji Li; Conglai Long; Tong Wei; Guoqing Ning; Jun Yan; Zhuangjun Fan

    2014-01-01

    This work presents NiS/graphene/carbon nanotube (NiS/GNS/CNT) composites as electrode material for the supercapacitor application in sea flashing signal systems. NiS nanosheets were closely anchored on the conductive GNS-CNT networks. As a result, the NiS/GNS/CNT electrode showed a high specific capacitance of 2 377 F·g-1 at 2 mV·s-1 and good cycling stability compared with the pure NiS (1 599 F·g-1 ). The enhanced electrochemical performances are attributed to the synergetic effect between the conductive carbon and the pseudo-capacitive NiS. The high performance supercapacitor may provide application in the sea flashing signal system.

  17. Aerosol assisted synthesis of hierarchical tin–carbon composites and their application as lithium battery anode materials

    KAUST Repository

    Guo, Juchen

    2013-01-01

    We report a method for synthesizing hierarchically structured tin-carbon (Sn-C) composites via aerosol spray pyrolysis. In this method, an aqueous precursor solution containing tin(ii) chloride and sucrose is atomized, and the resultant aerosol droplets carried by an inert gas are pyrolyzed in a high-temperature tubular furnace. Owing to the unique combination of high reaction temperature and short reaction time, this method is able to achieve a hetero-structure in which small Sn particles (15 nm) are uniformly embedded in a secondary carbon particle. This procedure allows the size and size distribution of the primary Sn particles to be tuned, as well as control over the size of the secondary carbon particles by addition of polymeric surfactant in the precursor solution. When evaluated as anode materials for lithium-ion batteries, the resultant Sn-C composites demonstrate attractive electrochemical performance in terms of overall capacity, electrochemical stability, and coulombic efficiency. © 2013 The Royal Society of Chemistry.

  18. Surface Modification of Carbon Nanotubes with Conjugated Polyelectrolytes: Fundamental Interactions and Applications in Composite Materials, Nanofibers, Electronics, and Photovoltaics

    KAUST Repository

    Ezzeddine, Alaa

    2015-10-01

    Ever since their discovery, Carbon nanotubes (CNTs) have been renowned to be potential candidates for a variety of applications. Nevertheless, the difficulties accompanied with their dispersion and poor solubility in various solvents have hindered CNTs potential applications. As a result, studies have been developed to address the dispersion problem. The solution is in modifying the surfaces of the nanotubes covalently or non-covalently with a desired dispersant. Various materials have been employed for this purpose out of which polymers are the most common. Non-covalent functionalization of CNTs via polymer wrapping represents an attractive method to obtain a stable and homogenous CNTs dispersion. This method is able to change the surface properties of the nanotubes without destroying their intrinsic structure and preserving their properties. This thesis explores and studies the surface modification and solublization of pristine single and multiwalled carbon nanotubes via a simple solution mixing technique through non-covalent interactions of CNTs with various anionic and cationic conjugated polyelectrolytes (CPEs). The work includes studying the interaction of various poly(phenylene ethynylene) electrolytes with MWCNTs and an imidazolium functionalized poly(3-hexylthiophene) with SWCNTs. Our work here focuses on the noncovalent modifications of carbon nanotubes using novel CPEs in order to use these resulting CPE/CNT complexes in various applications. Upon modifying the CNTs with the CPEs, the resulting CPE/CNT complex has been proven to be easily dispersed in various organic and aqueous solution with excellent homogeneity and stability for several months. This complex was then used as a nanofiller and was dispersed in another polymer matrix (poly(methyl methacrylate), PMMA). The PMMA/CPE/CNT composite materials were cast or electrospun depending on their desired application. The presence of the CPE modified CNTs in the polymer matrix has been proven to enhance

  19. Potentiometric urea biosensor based on multi-walled carbon nanotubes (MWCNTs)/silica composite material

    Energy Technology Data Exchange (ETDEWEB)

    Ahuja, Tarushee [National Physical Laboratory (Council of Scientific and Industrial Research), Dr. K.S. Krishnan Road, New Delhi-110012 (India); Department of Applied Chemistry, Delhi College of Engineering, University of Delhi, Bawana Road, Delhi-110042 (India); Kumar, D. [Department of Applied Chemistry, Delhi College of Engineering, University of Delhi, Bawana Road, Delhi-110042 (India); Singh, Nahar; Biradar, A.M. [National Physical Laboratory (Council of Scientific and Industrial Research), Dr. K.S. Krishnan Road, New Delhi-110012 (India); Rajesh, E-mail: rajesh_csir@yahoo.com [National Physical Laboratory (Council of Scientific and Industrial Research), Dr. K.S. Krishnan Road, New Delhi-110012 (India)

    2011-03-12

    A novel potentiometric urea biosensor has been fabricated with urease (Urs) immobilized multi-walled carbon nanotubes (MWCNTs) embedded in silica matrix deposited on the surface of indium tin oxide (ITO) coated glass plate. The enzyme Urs was covalently linked with the exposed free -COOH groups of functionalized MWCNTs (F-MWCNTs), which are subsequently incorporated within the silica matrix by sol-gel method. The Urs/MWCNTs/SiO{sub 2}/ITO composite modified electrode was characterized by Fourier transform infrared (FTIR) spectroscopy, thermal gravimetric analysis (TGA) and UV-visible spectroscopy. The morphologies and electrochemical performance of the modified Urs/MWCNTs/SiO{sub 2}/ITO electrode have been investigated by scanning electron microscopy (SEM) and potentiometric method, respectively. The synergistic effect of silica matrix, F-MWCNTs and biocompatibility of Urs/MWCNTs/SiO{sub 2} made the biosensor to have the excellent electro catalytic activity and high stability. The resulting biosensor exhibits a good response performance to urea detection with a wide linear range from 2.18 x 10{sup -5} to 1.07 x 10{sup -3} M urea. The biosensor shows a short response time of 10-25 s and a high sensitivity of 23 mV/decade/cm{sup 2}.

  20. Reversibly assembled cellular composite materials.

    Science.gov (United States)

    Cheung, Kenneth C; Gershenfeld, Neil

    2013-09-13

    We introduce composite materials made by reversibly assembling a three-dimensional lattice of mass-produced carbon fiber-reinforced polymer composite parts with integrated mechanical interlocking connections. The resulting cellular composite materials can respond as an elastic solid with an extremely large measured modulus for an ultralight material (12.3 megapascals at a density of 7.2 milligrams per cubic centimeter). These materials offer a hierarchical decomposition in modeling, with bulk properties that can be predicted from component measurements and deformation modes that can be determined by the placement of part types. Because site locations are locally constrained, structures can be produced in a relative assembly process that merges desirable features of fiber composites, cellular materials, and additive manufacturing.

  1. Hierarchical composites of polyaniline-graphene nanoribbons-carbon nanotubes as electrode materials in all-solid-state supercapacitors.

    Science.gov (United States)

    Liu, Mingkai; Miao, Yue-E; Zhang, Chao; Tjiu, Weng Weei; Yang, Zhibin; Peng, Huisheng; Liu, Tianxi

    2013-08-21

    A three dimensional (3D) polyaniline (PANI)-graphene nanoribbon (GNR)-carbon nanotube (CNT) composite, PANI-GNR-CNT, has been prepared via in situ polymerization of an aniline monomer on the surface of a GNR-CNT hybrid. Here, the 3D GNR-CNT hybrid has been conveniently prepared by partially unzipping the pristine multi-walled CNTs, while the residual CNTs act as "bridges" connecting different GNRs. The morphology and structure of the resulting hybrid materials have been characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), Raman spectroscopy and X-ray diffraction (XRD). Electrochemical tests reveal that the hierarchical PANI-GNR-CNT composite based on the two-electrode cell possesses much higher specific capacitance (890 F g(-1)) than the GNR-CNT hybrid (195 F g(-1)) and neat PANI (283 F g(-1)) at a discharge current density of 0.5 A g(-1). At the same time, the PANI-GNR-CNT composite displays good cycling stability with a retention ratio of 89% after 1000 cycles, suggesting that this novel PANI-GNR-CNT composite is a promising candidate for energy storage applications.

  2. Nano-composite materials

    Science.gov (United States)

    Lee, Se-Hee; Tracy, C. Edwin; Pitts, J. Roland

    2010-05-25

    Nano-composite materials are disclosed. An exemplary method of producing a nano-composite material may comprise co-sputtering a transition metal and a refractory metal in a reactive atmosphere. The method may also comprise co-depositing a transition metal and a refractory metal composite structure on a substrate. The method may further comprise thermally annealing the deposited transition metal and refractory metal composite structure in a reactive atmosphere.

  3. Preparation of carbon/siliconl pyrocarbon composite materials for anode of lithium-ion battery

    OpenAIRE

    2015-01-01

    In present study,silicon and pyrocarbon was coated on the low crystalline carbon fibers as core carbon using chemical vapor deposition technique,and effect of the thin film silicon /pyrocarbon coating on electrochemical properties was examined. Crystalline silicon was deposited on core carbon without the formation of SiC that was inert with lithium. Charge capacity (Li de-intercalation) of the pristine carbon fiber was successfully increased up to 630 mAh/g by coating with 11 mass% silicon an...

  4. Multilayer Electroactive Polymer Composite Material

    Science.gov (United States)

    Ounaies, Zoubeida (Inventor); Park, Cheol (Inventor); Harrison, Joycelyn S. (Inventor); Holloway, Nancy M. (Inventor); Draughon, Gregory K. (Inventor)

    2011-01-01

    An electroactive material comprises multiple layers of electroactive composite with each layer having unique dielectric, electrical and mechanical properties that define an electromechanical operation thereof when affected by an external stimulus. For example, each layer can be (i) a 2-phase composite made from a polymer with polarizable moieties and an effective amount of carbon nanotubes incorporated in the polymer for a predetermined electromechanical operation, or (ii) a 3-phase composite having the elements of the 2-phase composite and further including a third component of micro-sized to nano-sized particles of an electroactive ceramic incorporated in the polymer matrix.

  5. Multifunctional Composite Materials Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Polymeric composite materials that are currently utilized in aircraft structures are susceptible to significant damage from lightning strikes. Enhanced electrical...

  6. Study the Effect of Carbon Fiber Volume Fraction and their Orientations on the Thermal Conductivity of the Polymer Composite Materials.

    Directory of Open Access Journals (Sweden)

    Mohammed Sellab Hamza

    2008-01-01

    Full Text Available The effect of fiber volume fraction of the carbon fiber on the thermal conductivity of the polymer composite material was studied. Different percentages of carbon fibers were used (5%, 10%, 15%, 20%, and 25%. Specimens were made in two groups for unsaturated polyester as a matrix and carbon fibers, first group has parallel arrangement of fibers and the second group has perpendicular arrangement of fibers on the thermal flow, Lee's disk method was used for testing the specimens. This study showed that the values of the of thermal conductivity of the specimens when the fibers arranged in parallel direction was higher than that when the fibers arranged in the perpendicular direction The results indicated that the thermal conductivity increases with the increasing the fiber volume fraction. Minimum value was (0.64 W/m.?C for parallel arrangement and (0.1715 W/m.?C for perpendicular arrangement at (Vf = 5% .Maximum value for parallel and perpendicular were (2.65 W/m. ?C and (0.215 W/m.?C at (Vf = 25% respectively.

  7. Metallic carbon materials

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, M.L.; Crespi, V.H.; Louie, S.G.S.; Zettl, A.K.

    1999-11-30

    Novel metallic forms of planar carbon are described, as well as methods of designing and making them. Nonhexagonal arrangements of carbon are introduced into a graphite carbon network essentially without destroying the planar structure. Specifically a form of carbon comprising primarily pentagons and heptagons, and having a large density of states at the Fermi level is described. Other arrangements of pentagons and heptagons that include some hexagons, and structures incorporating squares and octagons are additionally disclosed. Reducing the bond angle symmetry associated with a hexagonal arrangement of carbons increases the likelihood that the carbon material will have a metallic electron structure.

  8. Nanostructured Black Phosphorus/Ketjenblack-Multiwalled Carbon Nanotubes Composite as High Performance Anode Material for Sodium-Ion Batteries.

    Science.gov (United States)

    Xu, Gui-Liang; Chen, Zonghai; Zhong, Gui-Ming; Liu, Yuzi; Yang, Yong; Ma, Tianyuan; Ren, Yang; Zuo, Xiaobing; Wu, Xue-Hang; Zhang, Xiaoyi; Amine, Khalil

    2016-06-08

    Sodium-ion batteries are promising alternatives to lithium-ion batteries for large-scale applications. However, the low capacity and poor rate capability of existing anodes for sodium-ion batteries are bottlenecks for future developments. Here, we report a high performance nanostructured anode material for sodium-ion batteries that is fabricated by high energy ball milling to form black phosphorus/Ketjenblack-multiwalled carbon nanotubes (BPC) composite. With this strategy, the BPC composite with a high phosphorus content (70 wt %) could deliver a very high initial Coulombic efficiency (>90%) and high specific capacity with excellent cyclability at high rate of charge/discharge (∼1700 mAh g(-1) after 100 cycles at 1.3 A g(-1) based on the mass of P). In situ electrochemical impedance spectroscopy, synchrotron high energy X-ray diffraction, ex situ small/wide-angle X-ray scattering, high resolution transmission electronic microscopy, and nuclear magnetic resonance were further used to unravel its superior sodium storage performance. The scientific findings gained in this work are expected to serve as a guide for future design on high performance anode material for sodium-ion batteries.

  9. High performance carbon-carbon composites

    Indian Academy of Sciences (India)

    Lalit M Manocha

    2003-02-01

    Carbon-carbon composites rank first among ceramic composite materials with a spectrum of properties and applications in various sectors. These composites are made of fibres in various directions and carbonaceous polymers and hydrocarbons as matrix precursors. Their density and properties depend on the type and volume fraction of reinforcement, matrix precursor used and end heat treatment temperature. Composites made with thermosetting resins as matrix precursors possess low densities (1.55–1.75 g/cm3) and well-distributed microporosity whereas those made with pitch as the matrix precursor, after densification exhibit densities of 1.8–2.0 g/cm3 with some mesopores, and those made by the CVD technique with hydrocarbon gases, possess intermediate densities and matrices with close porosities. The former (resin-based) composites exhibit high flexural strength, low toughness and low thermal conductivity, whereas the latter (pitch- and CVD-based) can be made with very high thermal conductivity (400–700 W/MK) in the fibre direction. Carbon-carbon composites are used in a variety of sectors requiring high mechanical properties at elevated temperatures, good frictional properties for brake pads in high speed vehicles or high thermal conductivity for thermal management applications. However, for extended life applications, these composites need to be protected against oxidation either through matrix modification with Si, Zr, Hf etc. or by multilayer oxidation protection coatings consisting of SiC, silica, zircon etc.

  10. Fabrication of free-standing pure carbon-based composite material with the combination of sp{sup 2}–sp{sup 3} hybridizations

    Energy Technology Data Exchange (ETDEWEB)

    Varga, M., E-mail: varga@fzu.cz [Institute of Physics of the ASCR, v.v.i., Cukrovarnicka 10, Prague 6 16253 (Czech Republic); Institute of Electronics and Photonics, FEI STU, Ilkovicova 3, 812 19 Bratislava (Slovakia); Vretenar, V. [Danubia NanoTech, s.r.o., Ilkovicova 3, 841 04 Bratislava (Slovakia); Institute of Physics of the SAS, Dubravska cesta 9, 845 11 Bratislava (Slovakia); Kotlar, M. [Institute of Electronics and Photonics, FEI STU, Ilkovicova 3, 812 19 Bratislava (Slovakia); Skakalova, V. [Danubia NanoTech, s.r.o., Ilkovicova 3, 841 04 Bratislava (Slovakia); Physics of Nanostructured Materials, University of Vienna, Boltzmanngasse 5, 1090 Vienna (Austria); Kromka, A. [Institute of Physics of the ASCR, v.v.i., Cukrovarnicka 10, Prague 6 16253 (Czech Republic)

    2014-07-01

    Composite structures have been in a center of interest for many decades. Carbon–carbon composites combine different carbon-based allotropes. Combining different carbon structures each with its unique property results in a new composite material with designed properties. In this contribution we present a technological procedure for preparation of a new flexible material consisting of single-wall carbon nanotubes (SWNTs) and nanocrystalline diamond (NCD). The fabrication process starts from the preparation of a paper made of SWNTs bundles followed by the CVD-growth of NCD in the interior of the SWNT paper. Keeping balance between the two competing processes during the CVD, i.e. growth of diamond particles versus etching SWNTs, is found as a key factor for the formation of a compact SWNT/NCD composite material. From a technological point of view, both processes are influenced mainly by the CVD conditions (temperature, gas composition, etc.) and/or substrate pretreatment. The essential idea of the diamond integration into the SWNT paper is demonstrated and discussed in more details. The morphology and structural aspects of the prepared composite material are further characterized by scanning electron microscopy and Raman spectroscopy.

  11. 美国HEXEL公司的碳纤维及其复合材料%CARBON FIBERS AND COMPOSITE MATERIALS IN HEXEL CORPORATION,USA

    Institute of Scientific and Technical Information of China (English)

    赵稼祥

    2001-01-01

    简要介绍美国第45届材料与加工工程促进学会年会与展览会概况及美国HEXEL公司碳纤维及其复合材料的现况与发展。%At the 45th SAMPE Conference and Exhibition there Were 8 famous carbon fibers corporations and incorporation’s in the world exhibited their carbon fibers & composites products. In this paper,present status & development of carbon fibers & composite materials in HEXEL Corporation,USA were briefly presented.

  12. Capacitor with a composite carbon foam electrode

    Energy Technology Data Exchange (ETDEWEB)

    Mayer, S.T.; Pekala, R.W.; Kaschmitter, J.L.

    1999-04-27

    Carbon aerogels used as a binder for granularized materials, including other forms of carbon and metal additives, are cast onto carbon or metal fiber substrates to form composite carbon thin film sheets. The thin film sheets are utilized in electrochemical energy storage applications, such as electrochemical double layer capacitors (aerocapacitors), lithium based battery insertion electrodes, fuel cell electrodes, and electrocapacitive deionization electrodes. The composite carbon foam may be formed by prior known processes, but with the solid particles being added during the liquid phase of the process, i.e. prior to gelation. The other forms of carbon may include carbon microspheres, carbon powder, carbon aerogel powder or particles, graphite carbons. Metal and/or carbon fibers may be added for increased conductivity. The choice of materials and fibers will depend on the electrolyte used and the relative trade off of system resistivity and power to system energy. 1 fig.

  13. Capacitor with a composite carbon foam electrode

    Energy Technology Data Exchange (ETDEWEB)

    Mayer, Steven T. (San Leandro, CA); Pekala, Richard W. (Pleasant Hill, CA); Kaschmitter, James L. (Pleasanton, CA)

    1999-01-01

    Carbon aerogels used as a binder for granularized materials, including other forms of carbon and metal additives, are cast onto carbon or metal fiber substrates to form composite carbon thin film sheets. The thin film sheets are utilized in electrochemical energy storage applications, such as electrochemical double layer capacitors (aerocapacitors), lithium based battery insertion electrodes, fuel cell electrodes, and electrocapacitive deionization electrodes. The composite carbon foam may be formed by prior known processes, but with the solid partides being added during the liquid phase of the process, i.e. prior to gelation. The other forms of carbon may include carbon microspheres, carbon powder, carbon aerogel powder or particles, graphite carbons. Metal and/or carbon fibers may be added for increased conductivity. The choice of materials and fibers will depend on the electrolyte used and the relative trade off of system resistivity and power to system energy.

  14. Method for fabricating composite carbon foam

    Energy Technology Data Exchange (ETDEWEB)

    Mayer, Steven T. (San Leandro, CA); Pekala, Richard W. (Pleasant Hill, CA); Kaschmitter, James L. (Pleasanton, CA)

    2001-01-01

    Carbon aerogels used as a binder for granularized materials, including other forms of carbon and metal additives, are cast onto carbon or metal fiber substrates to form composite carbon thin film sheets. The thin film sheets are utilized in electrochemical energy storage applications, such as electrochemical double layer capacitors (aerocapacitors), lithium based battery insertion electrodes, fuel cell electrodes, and electrocapacitive deionization electrodes. The composite carbon foam may be formed by prior known processes, but with the solid particles being added during the liquid phase of the process, i.e. prior to gelation. The other forms of carbon may include carbon microspheres, carbon powder, carbon aerogel powder or particles, graphite carbons. Metal and/or carbon fibers may be added for increased conductivity. The choice of materials and fibers will depend on the electrolyte used and the relative trade off of system resistivity and power to system energy.

  15. Friction Material Composites Materials Perspective

    CERN Document Server

    Sundarkrishnaa, K L

    2012-01-01

    Friction Material Composites is the first of the five volumes which strongly educates and updates engineers and other professionals in braking industries, research and test labs. It explains besides the formulation of design processes and its complete manufacturing input. This book gives an idea of mechanisms of friction and how to control them by designing .The book is  useful for designers  of automotive, rail and aero industries for designing the brake systems effectively with the integration of friction material composite design which is critical. It clearly  emphasizes the driving  safety and how serious designers should  select the design input. The significance of friction material component like brake pad or a liner as an integral part of the brake system of vehicles is explained. AFM pictures at nanolevel illustrate broadly the explanations given.

  16. Summary of the Effects of Two Years of Hygro-Thermal Cycling on a Carbon/Epoxy Composite Material

    Science.gov (United States)

    Kohlman, Lee W.; Binienda, Wieslaw K.; Roberts, Gary D.; Miller, Sandi G.; Pereira, J. Michael; Bail, Justin L.

    2011-01-01

    Composite materials are beginning to be used for structures in the fan section of commercial gas turbine engines. This paper explores the type of damage that could occur within one type of composite material after exposure to hygrothermal cycles (temperature/humidity cycles) that are representative of the environment in the fan section of an engine. The effect of this damage on composite material properties is measured. Chemical changes in the matrix material were limited to the exposed surface. Microcrack formation was identified in the composite material. This damage did not cause a significant reduction in tensile strength or impact penetration resistance of the composite material. Additional data is needed to assess the effect of damage on compressive strength.

  17. Self-response multi-functional composite material base on carbon nanotube paper using deicing, flame retardancy, thermal insulation, and lightning-strike protection

    Science.gov (United States)

    Chu, Hetao; Zhang, Zhichun; Liu, Yanju; Leng, Jinsong

    2015-04-01

    Carbon nanotube paper (CNP) based multi-functional composite material is an attractive candidate for deicing, flame retardancy, thermal insulation and lighting strike protection due to the excellent conductivity, light weight and thin dimensions. In this article, multi-functional carbon nanotube paper was fabricated successfully by using commercial carbon nanotube. As a deicing composite material, carbon nanotube was used directly without pretreatment in fabricating carbon nanotube paper. The conductivities of the carbon nanotube paper and deicing composite were 77.8S/cm and 64.9S/ respectively. Electrical heating and deicing performance were test by infrared camera with deicing time less than 220s and 450s to melt a certain amount of ice under different ambient condition. CNT was grafted by zirconium (IV) butoxide solution and dimethyl dichlorosilicane to form co-oligomers on the tube surface while oligomers decompose under a certain temperature to develop an inorganic layer of silicon zirconium oxide. The oxidizing temperature of carbon nanotube increases more than 20°C and the weight loss rate decreases 20% than the untreated carbon nanotube. Lightning protection material required high electro conductivity, due to the utmost high current in a short time. Therefore, silver nanoparticles were deposited on the surface of carbon nanotube with the diameter around 100nm. The conductivity increased sharply from 84s/cm to1756s/cm with the mount of 5.9wt% Ag of the modified carbon nanotube paper because the silver nanoparticles deposited on the surface. In addition, the silver modified also can be used as thermal insulation material decreasing the infrared radiation.

  18. Enhanced field emission from cerium hexaboride coated multiwalled carbon nanotube composite films: A potential material for next generation electron sources

    Energy Technology Data Exchange (ETDEWEB)

    Patra, Rajkumar; Ghosh, S., E-mail: santanu1@physics.iitd.ac.in [Nanostech Laboratory, Department of Physics, Indian Institute of Technology Delhi, New Delhi-16 (India); Sheremet, E.; Rodriguez, R. D.; Lehmann, D.; Gordan, O. D.; Zahn, D. R. T. [Semiconductor Physics, Technische Universität Chemnitz, 09126 Chemnitz (Germany); Jha, M.; Ganguli, A. K. [Department of Chemistry, Indian Institute of Technology Delhi, New Delhi-16 (India); Schmidt, H. [Material Systems for Nanoelectronics, Technische Universität Chemnitz, 09126 Chemnitz (Germany); Schulze, S. [Solid Surfaces Analysis, Technische Universität Chemnitz, 09126 Chemnitz (Germany); Schmidt, O. G. [Material Systems for Nanoelectronics, Technische Universität Chemnitz, 09126 Chemnitz (Germany); Institute for Integrative Nanosciences, IFW Dresden, Helmholtzstrasse 20, 01069 Dresden (Germany)

    2014-03-07

    Intensified field emission (FE) current from temporally stable cerium hexaboride (CeB{sub 6}) coated carbon nanotubes (CNTs) on Si substrate is reported aiming to propose the new composite material as a potential candidate for future generation electron sources. The film was synthesized by a combination of chemical and physical deposition processes. A remarkable increase in maximum current density, field enhancement factor, and a reduction in turn-on field and threshold field with comparable temporal current stability are observed in CeB{sub 6}-coated CNT film when compared to pristine CeB{sub 6} film. The elemental composition and surface morphology of the films, as examined by scanning electron microscopy, transmission electron microscopy, and energy dispersive X-ray measurements, show decoration of CeB{sub 6} nanoparticles on top and walls of CNTs. Chemical functionalization of CNTs by the incorporation of CeB{sub 6} nanoparticles is evident by a remarkable increase in intensity of the 2D band in Raman spectrum of coated films as compared to pristine CeB{sub 6} films. The enhanced FE properties of the CeB{sub 6} coated CNT films are correlated to the microstructure of the films.

  19. Self-Consistent Physical Properties of Carbon Nanotubes in Composite Materials

    Science.gov (United States)

    Pipes, R. B.; Frankland, S. J. V.; Hubert, P.; Saether, E.

    2002-12-01

    A set of relationships is developed for selected physical properties of single-walled carbon nanotubes (SWCN) and their hexagonal arrays as a function of nanotube size in terms of the chiral vector integer pair, (n,m). Properties include density, principal Young's modulus, and specific Young's modulus. Relationships between weight fraction and volume fraction of SWCN and their arrays are developed for polymeric mixtures.

  20. Development of carbon composite iron ore micropellets by using the microfines of iron ore and carbon-bearing materials in iron making

    Science.gov (United States)

    Pal, Jagannath; Ghorai, Satadal; Das, Avimanyu

    2015-02-01

    Iron ore microfines and concentrate have very limited uses in sintering processes. They are used in pelletization; however, this process is cost intensive. Furthermore, the microfines of non-coking coal and other carbon-bearing materials, e.g., blast-furnace flue dust (BFD) and coke fines, are not used extensively in the metallurgical industry because of operational difficulties and handling problems. In the present work, to utilize these microfines, coal composite iron oxide micropellets (2-6 mm in size) were produced through an innovative technique in which lime and molasses were used as binding materials in the micropellets. The micropellets were subsequently treated with CO2 or the industrial waste gas to induce the chemical bond formation. The results show that, at a very high carbon level of 22wt% (38wt% coal), the cold crushing strength and abrasion index of the micropellets are 2.5-3 kg/cm2 and 5wt%-9wt%, respectively; these values indicate that the pellets are suitable for cold handling. The developed micropellets have strong potential as a heat source in smelting reduction in iron making and sintering to reduce coke breeze. The micropellets produced with BFD and coke fines (8wt%-12wt%) were used in iron ore sintering and were observed to reduce the coke breeze consumption by 3%-4%. The quality of the produced sinter was at par with that of the conventional blast-furnace sinter.

  1. Hydrogen Storage in Iron/Carbon Nanopowder Composite Materials: Effect of Varying Spiked Iron Content on Hydrogen Adsorption

    Directory of Open Access Journals (Sweden)

    Chun-Lin Chu

    2013-01-01

    Full Text Available This study investigates the effects of varying the spiked iron content of iron/carbon nanopowder (Fe/CNP composite materials on hydrogen storage capacity. Among four such samples, a maximum hydrogen uptake of approximately 0.48 wt% was obtained with 14 wt% of spiked iron under 37 atm and 300 K. This higher hydrogen uptake capacity was believed to be closely related to the physisorption mechanism rather than chemisorption. In this case, the formation of maghemite catalyzed the attraction of hydrogen molecules and the CNP skeleton was the principal absorbent material for hydrogen storage. However, as the iron content exceeded 14 wt%, the formation of larger and poorly dispersed maghemite grains reduced the available surface areas of CNP for the storage of hydrogen molecules, leading to decreased uptake. Our study shows that hydrogen uptake capacities can be improved by appropriately adjusting the surface polarities of the CNP with well dispersed iron oxides crystals.

  2. The development and application of carbon nano composite material%浅谈碳纳米复合材料的应用与发展

    Institute of Scientific and Technical Information of China (English)

    彭复俊

    2013-01-01

      本文介绍一些碳纳米纤维管的应用与发展,综述了碳纳米纤维管/聚合物复合材料的制备方法及其聚合物结构复合材料和聚合物功能复合材料中的应用研究情况,在此基础上,分析了碳纳米纤维管在复合材料制备过程中的纯化、分散、损伤和界面等问题,并展望了今后碳纳米及复合材料的发展前景。%The article introduces the structure and properties of carbon nanotubes,carbon nanotube/polymer composites are reviewed in this paper the preparation methods and the structure of polymer composite materials and the application of polymer functional composite materials research situation,on this basis,the analysis of carbon nanotubes in the process of composite material preparation,purification, dispersion,damage and interface problems,and prospects the future development trend of the carbon nanotubes/polymer composites.

  3. Synthesis and electrochemical performance of mesoporous SiO{sub 2}–carbon nanofibers composite as anode materials for lithium secondary batteries

    Energy Technology Data Exchange (ETDEWEB)

    Hyun, Yura; Choi, Jin-Yeong [Department of Chemistry, Keimyung University (Korea, Republic of); Park, Heai-Ku [Department of Chemical Engineering, Keimyung University (Korea, Republic of); Bae, Jae Young [Department of Chemistry, Keimyung University (Korea, Republic of); Lee, Chang-Seop, E-mail: surfkm@kmu.ac.kr [Department of Chemistry, Keimyung University (Korea, Republic of)

    2016-10-15

    Highlights: • Mesoporous SiO{sub 2}–carbon nanofibers composite synthesized on Ni foam without any binder. • This composite was directly applied as anode material of Li secondary batteries. • Showed the highest initial (2420 mAh/g) and discharging (2092 mAh/g) capacity. • This material achieved a retention rate of 86.4% after 30 cycles. - Abstract: In this study, carbon nanofibers (CNFs) and mesoporous SiO{sub 2}–carbon nanofibers composite were synthesized and applied as the anode materials in lithium secondary batteries. CNFs and mesoporous SiO{sub 2}–CNFs composite were grown via chemical vapor deposition method with iron-copper catalysts. Mesoporous SiO{sub 2} materials were prepared by sol–gel method using tetraethylorthosilicate as the silica source and cetyltrimethylammoniumchloride as the template. Ethylene was used as the carbon source and passes into a quartz reactor of a tube furnace heated to 600 °C, and the temperature was maintained at 600 °C for 10 min to synthesize CNFs and mesoporous SiO{sub 2}–CNFs composite. The electrochemical characteristics of the as-prepared CNFs and mesoporous SiO{sub 2}–CNFs composite as the anode of lithium secondary batteries were investigated using a three-electrode cell. In particular, the mesoporous SiO{sub 2}–CNFs composites synthesized without binder after depositing mesoporous SiO{sub 2} on Ni foam showed the highest charging and discharging capacity and retention rate. The initial capacity (2420 mAh/g) of mesoporous SiO{sub 2}–CNFs composites decreased to 2092 mAh/g after 30 cycles at a retention rate of 86.4%.

  4. Preparation and Electrochemical Properties of Li3V2(PO4)3−xBrx/Carbon Composites as Cathode Materials for Lithium-Ion Batteries

    Science.gov (United States)

    Cao, Xiaoyu; Mo, Lulu; Zhu, Limin; Xie, Lingling

    2017-01-01

    Li3V2(PO4)3−xBrx/carbon (x = 0.08, 0.14, 0.20, and 0.26) composites as cathode materials for lithium-ion batteries were prepared through partially substituting PO43− with Br−, via a rheological phase reaction method. The crystal structure and morphology of the as-prepared composites were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and electrochemical properties were evaluated by charge/discharge cycling and electrochemical impedance spectroscopy (EIS). XRD results reveal that the Li3V2(PO4)3−xBrx/carbon composites with solid solution phase are well crystallized and have the same monoclinic structure as the pristine Li3V2(PO4)3/carbon composite. It is indicated by SEM images that the Li3V2(PO4)3−xBrx/carbon composites possess large and irregular particles, with an increasing Br− content. Among the Li3V2(PO4)3−xBrx/carbon composites, the Li3V2(PO4)2.86Br0.14/carbon composite shows the highest initial discharge capacity of 178.33 mAh·g−1 at the current rate of 30 mA·g−1 in the voltage range of 4.8–3.0 V, and the discharge capacity of 139.66 mAh·g−1 remains after 100 charge/discharge cycles. Even if operated at the current rate of 90 mA·g−1, Li3V2(PO4)2.86Br0.14/carbon composite still releases the initial discharge capacity of 156.57 mAh·g−1, and the discharge capacity of 123.3 mAh·g−1 can be maintained after the same number of cycles, which is beyond the discharge capacity and cycleability of the pristine Li3V2(PO4)3/carbon composite. EIS results imply that the Li3V2(PO4)2.86Br0.14/carbon composite demonstrates a decreased charge transfer resistance and preserves a good interfacial compatibility between solid electrode and electrolyte solution, compared with the pristine Li3V2(PO4)3/carbon composite upon cycling. PMID:28336886

  5. Direct Access to Mesoporous Crystalline TiO2/Carbon Composites with Large and Uniform Pores for Use as Anode Materials in Lithium Ion Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jinwoo [Pohang Univ. of Science and Technology (POSTECH) (Korea, Republic of); Jung, Yoon S. [Seoul National Univ. (Korea, Republic of); Warren, Scott C. [Cornell Univ., Ithaca, NY (United States); Kamperman, Marleen [Cornell Univ., Ithaca, NY (United States); Oh, Seung M. [Seoul National Univ. (Korea, Republic of); DiSalvo, Francis J. [Cornell Univ., Ithaca, NY (United States); Wiesner, Ulrich [Cornell Univ., Ithaca, NY (United States)

    2011-01-07

    Mesoporous and highly crystalline TiO2 (anatase)/carbon composites with large (>5 nm) and uniform pores were synthesized using PI-b-PEO block copolymers as structure directing agents. Pore sizes could be tuned by utilizing block copolymers with different molecular weights. The resulting mesoporous TiO2/carbon was successfully used as an anode material for Li ion batteries. Without addition of conducting aid (Super P), the electrode showed high capacity during the first insertion/desertion cycle due to carbon wiring inside the walls of mesoporous TiO2/carbon. The electrode further showed stable cycle performance up to 50 cycles and the specific charge capacity at 30 C was 38 mA h (g of TiO2)-1, which indicates CCM-TiO2/carbon can be used as a material for high rate use.

  6. Experimental evidence of localized plasmon resonance in composite materials containing single-wall carbon nanotubes

    Science.gov (United States)

    Shuba, M. V.; Paddubskaya, A. G.; Plyushch, A. O.; Kuzhir, P. P.; Slepyan, G. Ya.; Maksimenko, S. A.; Ksenevich, V. K.; Buka, P.; Seliuta, D.; Kasalynas, I.; Macutkevic, J.; Valusis, G.; Thomsen, C.; Lakhtakia, A.

    2012-04-01

    Experimental proof of localized plasmon resonance was found in thin films containing either single-walled carbon nanotubes (SWNT) or SWNT bundles of different length. All samples were prepared by a simple technique that permitted the selection of different SWNT lengths in different samples without significant differences in electronic properties. Fourier-transform infrared spectroscopy showed that an optical-density peak, the same as a terahertz conductivity peak, shifts to higher frequencies as the SWNT lengths are reduced—in agreement with a similar tendency predicted for the localized plasmon resonance in finite-length SWNTs [Slepyan , Phys. Rev. BPRBMDO1098-012110.1103/PhysRevB.81.205423 81, 205423 (2010)].

  7. Characteristics and Electrochemical Performance of Si-Carbon Nanofibers Composite as Anode Material for Binder-Free Lithium Secondary Batteries.

    Science.gov (United States)

    Hyun, Yura; Park, Heai-Ku; Park, Ho-Seon; Lee, Chang-Seop

    2015-11-01

    The carbon nanofibers (CNFs) and Si-CNFs composite were synthesized using a chemical vapor deposition (CVD) method with an iron-copper catalyst and silicon-covered Ni foam. Acetylene as a carbon source was flowed into the quartz reactor of a tubular furnace heated to 600 degrees C. This temperature was maintained for 10 min to synthesize the CNFs. The morphologies, compositions, and crystal quality of the prepared CNFs were characterized by Scanning electron microscopy (SEM), Energy dispersive spectroscopy (EDS), X-ray Diffraction (XRD), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). The electrochemical characteristics of the Si-CNFs composite as an anode of the Li secondary batteries were investigated using a three-electrode cell. The as-deposited Si-CNF composite on the Ni foam was directly employed as an working electrode without any binder, and lithium foil was used as the counter and reference electrode. A glass fiber separator was used as the separator membrane. Two kinds of electrolytes were employed; 1) 1 M LiPF6 was dissolved in a mixture of EC (ethylene carbonate): PC (propylene carbonate): EMC (Ethyl methyl carbonate) in a 1:1:1 volume ratio and 2) 1 M LiClO4 was dissolved in a mixture of propylene carbonate (PC): ethylene carbonate (EC) in a 1:1 volume ratio. The galvanostatic charge-discharge cycling and cyclic voltammetry measurements were carried out at room temperature by using a battery tester. The resulting Si-CNFs composite achieved the large discharge capacity of 613 mAh/g and much improved cycle-ability with the retention rate of 87% after 20 cycles.

  8. Mechanical Properties of Composite Materials

    Directory of Open Access Journals (Sweden)

    Mitsuhiro Okayasu

    2014-10-01

    Full Text Available An examination has been made of the mechanical and failure properties of several composite materials, such as a short and a long carbon fiber reinforced plastic (short- and long-CFRP and metal based composite material. The short CFRP materials were used for a recycled CFRP which fabricated by the following process: the CFRP, consisting of epoxy resin with carbon fiber, is injected to a rectangular plate cavity after mixing with acrylonitrile butadiene styrene resin with different weight fractions of CFRP. The fatigue and ultimate tensile strength (UTS increased with increasing CFRP content. These correlations, however, break down, especially for tensile strength, as the CFPR content becomes more than 70%. Influence of sample temperature on the bending strength of the long-CFRP was investigated, and it appears that the strength slightly decreases with increasing the temperature, due to the weakness in the matrix. Broken fiber and pull-out or debonding between the fiber and matrix were related to the main failure of the short- and long-CFRP samples. Mechanical properties of metal based composite materials have been also investigated, where fiber-like high hardness CuAl2 structure is formed in aluminum matrix. Excellent mechanical properties were obtained in this alloy, e.g., the higher strength and the higher ductility, compared tothe same alloy without the fiber-like structure. There are strong anisotropic effects on the mechanical properties due to the fiber-like metal composite in a soft Al based matrix.

  9. Enhanced electrochemical performance of porous activated carbon by forming composite with graphene as high-performance supercapacitor electrode material

    Science.gov (United States)

    Wang, Zhi-Hang; Yang, Jia-Ying; Wu, Xiong-Wei; Chen, Xiao-Qing; Yu, Jin-Gang; Wu, Yu-Ping

    2017-02-01

    In this work, a novel activated carbon containing graphene composite was developed using a fast, simple, and green ultrasonic-assisted method. Graphene is more likely a framework which provides support for activated carbon (AC) particles to form hierarchical microstructure of carbon composite. Scanning electron microscope (SEM), transmission electron microscope (TEM), Brunauer-Emmett-Teller (BET) surface area measurement, thermogravimetric analysis (TGA), Raman spectra analysis, XRD, and XPS were used to analyze the morphology and surface structure of the composite. The electrochemical properties of the supercapacitor electrode based on the as-prepared carbon composite were investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), charge/discharge, and cycling performance measurements. It exhibited better electrochemical performance including higher specific capacitance (284 F g-1 at a current density of 0.5 A g-1), better rate behavior (70.7% retention), and more stable cycling performance (no capacitance fading even after 2000 cycles). It is easier for us to find that the composite produced by our method was superior to pristine AC in terms of electrochemical performance due to the unique conductive network between graphene and AC.

  10. Cerium oxide nanoparticles/multi-wall carbon nanotubes composites: Facile synthesis and electrochemical performances as supercapacitor electrode materials

    Science.gov (United States)

    Deng, Dongyang; Chen, Nan; Li, Yuxiu; Xing, Xinxin; Liu, Xu; Xiao, Xuechun; Wang, Yude

    2017-02-01

    Cerium oxide nanoparticles/multi-wall carbon nanotubes (MWCNTs) composites are synthesized by a facile hydrothermal method without any surfactant or template. The morphology and microstructure of samples are examined by scanning electron microscopy (SEM), transition electron microscopy (TEM), X-ray diffraction (XRD), Raman spectrum and X-ray photoelectron spectroscopy (XPS). Electrochemical properties of the MWCNTs, the pure CeO2, and the CeO2/MWCNTs nanocomposites electrodes are investigated by cyclic voltammetry (CV), galvanostatic charge/discharge (GDC) and electrochemical impedance spectroscopy (EIS) measurements. The CeO2/MWCNTs nanocomposite (at the mole ratio of 1:1) electrode exhibits much larger specific capacitance compared with both the MWCNTs electrode and the pure CeO2 electrode and significantly improves cycling stability compared to the pure CeO2 electrode. The CeO2/MWCNTs nanocomposite (at the mole ratio of 1:1) achieves a specific capacitance of 455.6 F g-1 at the current density of 1 A g-1. Therefore, the as prepared CeO2/MWCNTs nanocomposite is a promising electrode material for high-performance supercapacitors.

  11. The Effect of Graphite Particle Size on Properties of Low Carbon MgO-C Composite Materials

    Institute of Scientific and Technical Information of China (English)

    LI Lin; HONG Yanruo; SUN Jialin; OUYANG Junhua; HE Zhiyong; YU Li

    2004-01-01

    The effects of graphite granularity on the properties of low carbon MgO-C based materials have been investigated in the work. Large crystal fused magnesia, natural flake graphite with different particle sizes and anti-oxidant were adopted as raw material for preparation of specimens.However, the results show that the physical properties,oxidation resistance and thermal shock resistance of low carbon MgO- C materials with content of 4.0 wt % graphite are improved obviously through the use of special and suitable size graphite. The excellent performance achieved was considered as a result of microstructure modification of MgO-C materials. Therefore, it is suggested that both fine and micro grade natural flake graphite used for production of low carbon MgO- C bricks.

  12. Nanostructured composite reinforced material

    Science.gov (United States)

    Seals, Roland D.; Ripley, Edward B.; Ludtka, Gerard M.

    2012-07-31

    A family of materials wherein nanostructures and/or nanotubes are incorporated into a multi-component material arrangement, such as a metallic or ceramic alloy or composite/aggregate, producing a new material or metallic/ceramic alloy. The new material has significantly increased strength, up to several thousands of times normal and perhaps substantially more, as well as significantly decreased weight. The new materials may be manufactured into a component where the nanostructure or nanostructure reinforcement is incorporated into the bulk and/or matrix material, or as a coating where the nanostructure or nanostructure reinforcement is incorporated into the coating or surface of a "normal" substrate material. The nanostructures are incorporated into the material structure either randomly or aligned, within grains, or along or across grain boundaries.

  13. Bio-Inspired Hierarchical Nanofibrous Fe3O4-TiO2-Carbon Composite as a High-Performance Anode Material for Lithium-Ion Batteries.

    Science.gov (United States)

    Li, Shun; Wang, Mengya; Luo, Yan; Huang, Jianguo

    2016-07-13

    A bioinspired hierarchical nanofibrous Fe3O4-TiO2-carbon composite was fabricated by employing natural cellulose substance (e.g., filter paper) as both the scaffold and the carbon source and showed improved electrochemical performances when it is employed as an anode material for lithium-ion batteries. FeOOH nanoparticles were first grown uniformly onto the surface of the titania thin-layer precoated cellulose nanofibers, and thereafter, the as-prepared FeOOH-TiO2-cellulose composite was calcined and carbonized in argon atmosphere at 500 °C for 6 h to produce the Fe3O4-TiO2-carbon composite. The resultant composite possesses a hierarchical structure that was faithfully inherited from the initial cellulose substance, which was composed of titania-coated carbon fibers with corncob-like shaped Fe3O4 nanoparticles immobilized on the surfaces. The diameter of the composite nanofiber is ca. 100-200 nm, and the diameter of the Fe3O4 nanoparticle is about 30 nm, which is coated with an ultrathin carbon layer with a thickness about 3 nm. This composite displayed superior lithium-ion storage performance. It showed a first-cycle discharge capacity of 1340 mAh/g, delivering a stable reversible capacity of ca. 525 mAh/g after 100 charge-discharge cycles at a current density of 100 mA/g, and the efficiency is as high as ca. 95% of the theoretical value. This is much higher than those of the commercial Fe3O4 powder (160 mAh/g) and the Fe3O4-carbon counter material (310 mAh/g). It was demonstrated that the thin titania precoating layer (thickness ca. 3-5 nm) is necessary for the high content loading of the Fe3O4 nanoparticles onto the carbon nanofibers. Owing to the unique three-dimensional porous network structure of the carbon-fiber scaffold, together with the ultrathin outer carbon-coating layer, the composite showed significantly improved cycling stability and rate capability.

  14. Catalytic graphitization of carbon/carbon composites by lanthanum oxide

    Institute of Scientific and Technical Information of China (English)

    ZHANG Can; LU Guimin; SUN Ze; YU Jianguo

    2012-01-01

    Graphitized carbon/carbon composites were prepared by the process of catalytic graphitization with the rare-earth catalyst,lanthanum oxide (La2O3),in order to increase the degree of graphitization and reduce the electrical resistivity.The modified coal tar pitch and coal-based needle coke were used as carbon source,and a small amount of La2O3 was added to catalyze the graphitization of the disordered carbon materials.The effects of La2O3 catalyst on the graphitization degree and microstructure oftbe carbon/carbon composites were investigated by X-ray diffraction,scanning electron microscopy,and Raman spectroscopy.The results showed that La2O3 promoted the formation of more perfect and larger crystallites,and improved the electrical/mechanical properties of carbon/carbon composites.Carbon/carbon composites with a lower electrical resistivity (7.0 μΩ·m) could be prepared when adding 5 wt.% La2O3 powder with heating treatment at 2800 ℃.The catalytic effect of La2O3 for the graphitization of carbon/carbon composites was analyzed.

  15. High performance amorphous-Si@SiOx/C composite anode materials for Li-ion batteries derived from ball-milling and in situ carbonization

    Science.gov (United States)

    Wang, Dingsheng; Gao, Mingxia; Pan, Hongge; Wang, Junhua; Liu, Yongfeng

    2014-06-01

    Amorphous-Si@SiOx/C composites with amorphous Si particles as core and coated with a double layer of SiOx and carbon are prepared by ball-milling crystal micron-sized silicon powders and carbonization of the citric acid intruded in the ball-milled Si. Different ratios of Si to citric acid are used in order to optimize the electrochemical performance. It is found that SiOx exists naturally at the surfaces of raw Si particles and its content increases to ca. 24 wt.% after ball-milling. With an optimized Si to citric acid weight ratio of 1/2.5, corresponding to 8.4 wt.% C in the composite, a thin carbon layer is coated on the surfaces of a-Si@SiOx particles, moreover, floc-like carbon also forms and connects the carbon coated a-Si@SiOx particles. The composite provides a capacity of 1450 mA h g-1 after 100 cycles at a current density of 100 mA g1, and a capacity of 1230 mA h g-1 after 100 cycles at 500 mA g1 as anode material for lithium-ion batteries. Effects of ball-milling and the addition of citric acid on the microstructure and electrochemical properties of the composites are revealed and the mechanism of the improvement in electrochemical properties is discussed.

  16. Influence of Gas Composition on the Resisting Ability of Gunning Material for Blast Furnace to Carbon Monoxide Corrosion

    Institute of Scientific and Technical Information of China (English)

    YANG Lihong; LIU Liu; GUO Yanling; CAO Feng; MENG Qingmin; LONG Shigang

    2002-01-01

    This paper describes the resisting ability of gunning material for blast furnace to carbon monoxide corrosion under the mixed gas condition through inletting hydrogen into pure CO.A standard for testing the resisting ability of refractory to Co corrosion with mixed gas instead of pure CO has also been discussed. The results show:the addition of hydrogen accelerates the CO corrosion on gunning material;the same results has been reached with the CO,200 hours to test the resisting ability of refractory to carbon monoxide corrosion.

  17. Micromechanics of Composite Materials

    CERN Document Server

    Dvorak, George

    2013-01-01

    This book presents a broad exposition of analytical and numerical methods for modeling composite materials, laminates, polycrystals and other heterogeneous solids, with emphasis on connections between material properties and responses on several length scales, ranging from the nano and microscales to the macroscale. Many new results and methods developed by the author are incorporated into a rich fabric of the subject, which has been explored by several researchers over the last 40 years.   The first  part of the book reviews anisotropic elasticity theory, and then it describes the frequently used procedures and theorems for bounding and estimating overall properties, local fields and energy changes in elastic inhomogeneities, heterogeneous media, fiber composites and functionally graded materials.  Those are caused by mechanical loads and by phase eigenstrains, such as thermal, transformation and inelastic strains, and also by cavities and cracks.    Worked examples show that the eigendeformations may...

  18. An experimental investigation of using carbon foam-PCM-MWCNTs composite materials for thermal management of electronic devices under pulsed power modes

    Science.gov (United States)

    Alshaer, W. G.; Rady, M. A.; Nada, S. A.; Palomo Del Barrio, Elena; Sommier, Alain

    2017-02-01

    The present article reports on a detailed experimental investigation of using carbon foam-PCM-MWCNTs composite materials for thermal management (TM) of electronic devices subjected to pulsed power. The TM module was fabricated by infiltrating paraffin wax (RT65) as a phase change material (PCM) and multi walled carbon nanotubes (MWCNTs) as a thermal conductivity enhancer in a carbon foam as a base structure. Two carbon foam materials of low and high values of thermal conductivities, CF20 and KL1-250 (3.1 and 40 W/m K), were tested as a base structure for the TM modules. Tests were conducted at different power intensities and power cycling/loading modes. Results showed that for all power varying modes and all carbon foams, the infiltration of RT65 into carbon foam reduces the temperature of TM module and results in damping the temperature spikes height. Infiltration of MWCNTS into RT65 further improves the effectiveness of TM module. Temperature damping was more pronounced in stand-alone pulsed power cycles as compared to pulsed power spikes modes. The effectiveness of inclusion of RT65 and RT65/MWCNTs in damping the temperature spikes height is remarkable in TM modules based on KL1-250 as compared to CF-20.

  19. An experimental investigation of using carbon foam-PCM-MWCNTs composite materials for thermal management of electronic devices under pulsed power modes

    Science.gov (United States)

    Alshaer, W. G.; Rady, M. A.; Nada, S. A.; Palomo Del Barrio, Elena; Sommier, Alain

    2016-05-01

    The present article reports on a detailed experimental investigation of using carbon foam-PCM-MWCNTs composite materials for thermal management (TM) of electronic devices subjected to pulsed power. The TM module was fabricated by infiltrating paraffin wax (RT65) as a phase change material (PCM) and multi walled carbon nanotubes (MWCNTs) as a thermal conductivity enhancer in a carbon foam as a base structure. Two carbon foam materials of low and high values of thermal conductivities, CF20 and KL1-250 (3.1 and 40 W/m K), were tested as a base structure for the TM modules. Tests were conducted at different power intensities and power cycling/loading modes. Results showed that for all power varying modes and all carbon foams, the infiltration of RT65 into carbon foam reduces the temperature of TM module and results in damping the temperature spikes height. Infiltration of MWCNTS into RT65 further improves the effectiveness of TM module. Temperature damping was more pronounced in stand-alone pulsed power cycles as compared to pulsed power spikes modes. The effectiveness of inclusion of RT65 and RT65/MWCNTs in damping the temperature spikes height is remarkable in TM modules based on KL1-250 as compared to CF-20.

  20. Effects of femoral component material properties on cementless fixation in total hip arthroplasty. A comparison study between carbon composite, titanium alloy, and stainless steel.

    Science.gov (United States)

    Otani, T; Whiteside, L A; White, S E; McCarthy, D S

    1993-02-01

    Carbon-fiber-reinforced-carbon composite material is an attractive implant material because its modulus of elasticity can be made similar to that of cortical bone. This study investigated the effect of femoral prosthesis elastic modulus on cementless implant fixation. Distal, as well as proximal, relative micromovements between implant and bone were measured in two testing protocols (axial-load and torsional-load), comparing identically shaped carbon composite (modulus of elasticity = 18.6 GPa), Ti6Al4V (100 GPa), and 630 stainless steel (200 GPa) prostheses. In the axial-load test, proximal mediolateral micromotions were significantly larger in the flexible composite stem than in the two metals. In the torsional-load test, rotational micromotions and "slop" displacements in the flexible stem were significantly larger proximally and significantly smaller distally than in the two metals. While these results suggest that proximal stress transfer may be improved by a flexible stem, they raise the possibility of increased proximal micromotion, and suggest that improved proximal fixation may be necessary to achieve clinical success with flexible composite femoral components.

  1. Polymer Matrix Composite Material Oxygen Compatibility

    Science.gov (United States)

    Owens, Tom

    2001-01-01

    Carbon fiber/polymer matrix composite materials look promising as a material to construct liquid oxygen (LOX) tanks. Based on mechanical impact tests the risk will be greater than aluminum, however, the risk can probably be managed to an acceptable level. Proper tank design and operation can minimize risk. A risk assessment (hazard analysis) will be used to determine the overall acceptability for using polymer matrix composite materials.

  2. Biotechnology and Composite Materials

    Science.gov (United States)

    1993-04-01

    Biotechnology, in general terms, is the science and engineering of using living organisms for making useful products such as pharmaceuticals, foods , fuels...chemicals, materials or in waste treatment processes and clinical and chemical analyses. It encompases the prosaic form of using yeast cells to make...ductile component of the composite. Table 1. Mechanical Properties of Ceramics, Cermets, and Abalone Shell •if KIC Hardness MPa MPam 1n 2 /2 Mohs KIlN

  3. Composite materials formed with anchored nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Seals, Roland D; Menchhofer, Paul A; Howe, Jane Y; Wang, Wei

    2015-03-10

    A method of forming nano-structure composite materials that have a binder material and a nanostructure fiber material is described. A precursor material may be formed using a mixture of at least one metal powder and anchored nanostructure materials. The metal powder mixture may be (a) Ni powder and (b) NiAl powder. The anchored nanostructure materials may comprise (i) NiAl powder as a support material and (ii) carbon nanotubes attached to nanoparticles adjacent to a surface of the support material. The process of forming nano-structure composite materials typically involves sintering the mixture under vacuum in a die. When Ni and NiAl are used in the metal powder mixture Ni.sub.3Al may form as the binder material after sintering. The mixture is sintered until it consolidates to form the nano-structure composite material.

  4. An in situ method of creating metal oxide–carbon composites and their application as anode materials for lithium-ion batteries

    KAUST Repository

    Yang, Zichao

    2011-01-01

    Transition metal oxides are actively investigated as anode materials for lithium-ion batteries (LIBs), and their nanocomposites with carbon frequently show better performance in galvanostatic cycling studies, compared to the pristine metal oxide. An in situ, scalable method for creating a variety of transition metal oxide-carbon nanocomposites has been developed based on free-radical polymerization and cross-linking of poly(acrylonitrile) in the presence of the metal oxide precursor containing vinyl groups. The approach yields a cross-linked polymer network, which uniformly incorporates nanometre-sized transition metal oxide particles. Thermal treatment of the organic-inorganic hybrid material produces nearly monodisperse metal oxide nanoparticles uniformly embedded in a porous carbon matrix. Cyclic voltammetry and galvanostatic cycling electrochemical measurements in a lithium half-cell are used to evaluate the electrochemical properties of a Fe3O 4-carbon composite created using this approach. These measurements reveal that when used as the anode in a lithium battery, the material exhibits stable cycling performance at both low and high current densities. We further show that the polymer/nanoparticle copolymerization approach can be readily adapted to synthesize metal oxide/carbon nanocomposites based on different particle chemistries for applications in both the anode and cathode of LIBs. © 2011 The Royal Society of Chemistry.

  5. Continuous Carbon Nanotube-Ultrathin Graphite Hybrid Foams for Increased Thermal Conductivity and Suppressed Subcooling in Composite Phase Change Materials.

    Science.gov (United States)

    Kholmanov, Iskandar; Kim, Jaehyun; Ou, Eric; Ruoff, Rodney S; Shi, Li

    2015-12-22

    Continuous ultrathin graphite foams (UGFs) have been actively researched recently to obtain composite materials with increased thermal conductivities. However, the large pore size of these graphitic foams has resulted in large thermal resistance values for heat conduction from inside the pore to the high thermal conductivity graphitic struts. Here, we demonstrate that the effective thermal conductivity of these UGF composites can be increased further by growing long CNT networks directly from the graphite struts of UGFs into the pore space. When erythritol, a phase change material for thermal energy storage, is used to fill the pores of UGF-CNT hybrids, the thermal conductivity of the UGF-CNT/erythritol composite was found to increase by as much as a factor of 1.8 compared to that of a UGF/erythritol composite, whereas breaking the UGF-CNT bonding in the hybrid composite resulted in a drop in the effective room-temperature thermal conductivity from about 4.1 ± 0.3 W m(-1) K(-1) to about 2.9 ± 0.2 W m(-1) K(-1) for the same UGF and CNT loadings of about 1.8 and 0.8 wt %, respectively. Moreover, we discovered that the hybrid structure strongly suppresses subcooling of erythritol due to the heterogeneous nucleation of erythritol at interfaces with the graphitic structures.

  6. Carbon Fiber Foam Composites and Methods for Making the Same

    Science.gov (United States)

    Leseman, Zayd Chad (Inventor); Atwater, Mark Andrew (Inventor); Phillips, Jonathan (Inventor)

    2014-01-01

    Exemplary embodiments provide methods and apparatus of forming fibrous carbon foams (FCFs). In one embodiment, FCFs can be formed by flowing a fuel rich gas mixture over a catalytic material and components to be encapsulated in a mold to form composite carbon fibers, each composite carbon fiber having a carbon phase grown to encapsulate the component in situ. The composite carbon fibers can be intertwined with one another to form FCFs having a geometry according to the mold.

  7. Advanced composite materials and processes

    Science.gov (United States)

    Baucom, Robert M.

    1991-01-01

    Composites are generally defined as two or more individual materials, which, when combined into a single material system, results in improved physical and/or mechanical properties. The freedom of choice of the starting components for composites allows the generation of materials that can be specifically tailored to meet a variety of applications. Advanced composites are described as a combination of high strength fibers and high performance polymer matrix materials. These advanced materials are required to permit future aircraft and spacecraft to perform in extended environments. Advanced composite precursor materials, processes for conversion of these materials to structures, and selected applications for composites are reviewed.

  8. Failure Modes in Composite Materials.

    Science.gov (United States)

    1987-05-19

    Derek, An Introduction to Composite Materials , New York: Cambridge University Press, 1981. 12. Jamison, R. D., Mechanical Engineering Department...1978. 19. Tsai, Stephen W., Introduction to Composite Materials , Lancaster, Pennsylvania: Technomic Publishing Company, Inc., 1980. 4,’ * .20. Vernon

  9. C-LFP-multi-walled carbon nanotubes composite cathode materials synthesized by solid-state reaction for lithium ion batteries.

    Science.gov (United States)

    Hwang, Yun-Hwa; Prabakar, S J Richard; Pyo, Myoungho

    2013-08-01

    Multi-walled carbon nanotubes (MWNT) was utilized as a conductive additive to enhance the capacity and rate capability of carbon coated LiFePO4 (C-LFP). Composites of C-LFP with MWNT (C-LFP-MWNT) were prepared by blending MWNT at different stages of C-LFP synthesis. The pre-blending (PrB) of MWNT (5, 10, 15 wt%) with LFP precursor (PrB-C-LFP-MWNT) before calcination in a reducing environment (5 vol% H2 in N2) at 750 degrees C, produced phase pure crystalline LFP with a reduction in particle size as increase in MWNT content. This was contrasted with post-blending (PoB) of MWNT with as-synthesized C-LFP (PoB-C-LFP-MWNT), which gave inferior electrochemical performances. The PrB-C-LFP-MWNT (10 wt%) composite showed better cycle stability, higher rate capability, and faster Li diffusion characteristics than PoB-C-LFP-MWNT.

  10. Advanced composite materials for optomechanical systems

    Science.gov (United States)

    Zweben, Carl

    2013-09-01

    Polymer matrix composites (PMCs) have been well established in optomechanical systems for several decades. The other three classes of composites; metal matrix composites (MMCs), ceramic matrix composites (CMCs), and carbon matrix composites (CAMCs) are making significant inroads. The latter include carbon/carbon (C/C) composites (CCCs). The success of composites has resulted in increasing use in consumer, industrial, scientific, and aerospace/defense optomechanical applications. Composites offer significant advantages over traditional materials, including high stiffnesses and strengths, near-zero and tailorable coefficients of thermal expansion (CTEs), tailorable thermal conductivities (from very low to over twice that of copper), and low densities. In addition, they lack beryllium's toxicity problems. Some manufacturing processes allow parts consolidation, reducing machining and joining operations. At present, PMCs are the most widely used composites. Optomechanical applications date from the 1970s. The second High Energy Astrophysical Observatory spacecraft, placed in orbit in 1978, had an ultrahigh-modulus carbon fiber-reinforced epoxy (carbon/epoxy) optical bench metering structure. Since then, fibers and matrix materials have advanced significantly, and use of carbon fiber-reinforced polymers (CFRPs) has increased steadily. Space system examples include the Hubble Space Telescope metering truss and instrument benches, Upper Atmosphere Research Satellite (UARS), James Webb Space Telescope and many others. Use has spread to airborne applications, such as SOFIA. Perhaps the most impressive CFRP applications are the fifty-four 12m and twelve 7m moveable ground-based ALMA antennas. The other three classes of composites have a number of significant advantages over PMCs, including no moisture absorption or outgassing of organic compounds. CCC and CMC components have flown on a variety of spacecraft. MMCs have been used in space, aircraft, military and industrial

  11. Hybrid Composites Based on Carbon Fiber/Carbon Nanofilament Reinforcement

    Directory of Open Access Journals (Sweden)

    Mehran Tehrani

    2014-05-01

    Full Text Available Carbon nanofilament and nanotubes (CNTs have shown promise for enhancing the mechanical properties of fiber-reinforced composites (FRPs and imparting multi-functionalities to them. While direct mixing of carbon nanofilaments with the polymer matrix in FRPs has several drawbacks, a high volume of uniform nanofilaments can be directly grown on fiber surfaces prior to composite fabrication. This study demonstrates the ability to create carbon nanofilaments on the surface of carbon fibers employing a synthesis method, graphitic structures by design (GSD, in which carbon structures are grown from fuel mixtures using nickel particles as the catalyst. The synthesis technique is proven feasible to grow nanofilament structures—from ethylene mixtures at 550 °C—on commercial polyacrylonitrile (PAN-based carbon fibers. Raman spectroscopy and electron microscopy were employed to characterize the surface-grown carbon species. For comparison purposes, a catalytic chemical vapor deposition (CCVD technique was also utilized to grow multiwall CNTs (MWCNTs on carbon fiber yarns. The mechanical characterization showed that composites using the GSD-grown carbon nanofilaments outperform those using the CCVD-grown CNTs in terms of stiffness and tensile strength. The results suggest that further optimization of the GSD growth time, patterning and thermal shield coating of the carbon fibers is required to fully materialize the potential benefits of the GSD technique.

  12. Composite materials processing, applications, characterizations

    CERN Document Server

    2017-01-01

    Composite materials are used as substitutions of metals/traditional materials in aerospace, automotive, civil, mechanical and other industries. The present book collects the current knowledge and recent developments in the characterization and application of composite materials. To this purpose the volume describes the outstanding properties of this class of advanced material which recommend it for various industrial applications.

  13. Inkjet-Printed Organic Field-Effect Transistor by Using Composite Semiconductor Material of Carbon Nanoparticles and Poly(3-Hexylthiophene

    Directory of Open Access Journals (Sweden)

    Chih-Ting Lin

    2011-01-01

    Full Text Available Poly(3-hexylthiophene, P3HT, has been widely used in organic electronics as a semiconductor material. It suffers from the low carrier mobility characteristics. This limits P3HT to be employed in applications. Therefore, the blending semiconductor material, carbon nanoparticle (CNP, and P3HT, are developed and examined by inkjet-printing organic field-effect transistor technology in this work. The effective carrier mobility of fabricated OFETs can be enhanced by 8 folds with adding CNP and using O2 plasma treatment. At the same time, the transconductance of fabricated OFETs is also raised by 5 folds. Based on the observations of SEM, XRD, and FTIR, these improvements are contributed to the local field induced by the formation of CNP/P3HT complexes. This observation presents an insight of the development in organic semiconductor materials. Moreover, this work also offers a low-cost and effective semiconductor material for inkjet-printing technology in the development of organic electronics.

  14. Osteogenesis and cytotoxicity of a new Carbon Fiber/Flax/Epoxy composite material for bone fracture plate applications.

    Science.gov (United States)

    Bagheri, Zahra S; Giles, Erica; El Sawi, Ihab; Amleh, Asma; Schemitsch, Emil H; Zdero, Radovan; Bougherara, Habiba

    2015-01-01

    This study is part of an ongoing program to develop a new CF/Flax/Epoxy bone fracture plate to be used in orthopedic trauma applications. The purpose was to determine this new plate's in-vitro effects on the level of bone formation genes, as well as cell viability in comparison with a medical grade metal (i.e. stainless steel) commonly employed for fabrication of bone plates (positive control). Cytotoxicity and osteogenesis induced by wear debris of the material were assessed using Methyl Tetrazolium (MTT) assay and reverse transcription polymerase chain reaction (RT-PCR) for 3 osteogenesis specific gene markers, including bone morphogenetic proteins (BMP2), runt-related transcription factor 2 (Runx2) and Osterix. Moreover, the Flax/Epoxy and CF/Epoxy composites were examined separately for their wettability properties by water absorption and contact angle (CA) tests using the sessile drop technique. The MTT results for indirect and direct assays indicated that the CF/Flax/Epoxy composite material showed comparable cell viability with no cytotoxicity at all incubation times to that of the metal group (p≥0.05). Osteogenesis test results showed that the expression level of Runx2 marker induced by CF/Flax/Epoxy were significantly higher than those induced by metal after 48 h (p=0.57). Also, the Flax/Epoxy composite revealed a hydrophilic character (CA=68.07°±2.05°) and absorbed more water up to 17.2% compared to CF/Epoxy, which reached 1.25% due to its hydrophobic character (CA=93.22°±1.95°) (p<0.001). Therefore, the new CF/Flax/Epoxy may be a potential candidate for medical applications as a bone fracture plate, as it showed similar cell viability with no negative effect on gene expression levels responsible for bone formation compared to medical grade stainless steel.

  15. Carbon Fiber Composite Monoliths as Catalyst Supports

    Energy Technology Data Exchange (ETDEWEB)

    Contescu, Cristian I [ORNL; Gallego, Nidia C [ORNL; Pickel, Joseph M [ORNL; Blom, Douglas Allen [ORNL; Burchell, Timothy D [ORNL

    2006-01-01

    Carbon fiber composite monoliths are rigid bodies that can be activated to a large surface area, have tunable porosity, and proven performance in gas separation and storage. They are ideal as catalyst supports in applications where a rigid support, with open structure and easy fluid access is desired. We developed a procedure for depositing a dispersed nanoparticulate phase of molybdenum carbide (Mo2C) on carbon composite monoliths in the concentration range of 3 to 15 wt% Mo. The composition and morphology of this phase was characterized using X-ray diffraction and electron microscopy, and a mechanism was suggested for its formation. Molybdenum carbide is known for its catalytic properties that resemble those of platinum group metals, but at a lower cost. The materials obtained are expected to demonstrate catalytic activity in a series of hydrocarbon reactions involving hydrogen transfer. This project demonstrates the potential of carbon fiber composite monoliths as catalyst supports.

  16. Carbon Fiber Composite Monoliths for Catalyst Supports

    Energy Technology Data Exchange (ETDEWEB)

    Contescu, Cristian I [ORNL; Gallego, Nidia C [ORNL; Pickel, Joseph M [ORNL; Blom, Douglas Allen [ORNL; Burchell, Timothy D [ORNL

    2006-01-01

    Carbon fiber composite monoliths are rigid bodies that can be activated to a large surface area, have tunable porosity, and proven performance in gas separation and storage. They are ideal as catalyst supports in applications where a rigid support, with open structure and easy fluid access is desired. We developed a procedure for depositing a dispersed nanoparticulate phase of molybdenum carbide (Mo2C) on carbon composite monoliths in the concentration range of 3 to 15 wt% Mo. The composition and morphology of this phase was characterized using X-ray diffraction and electron microscopy, and a mechanism was suggested for its formation. Molybdenum carbide is known for its catalytic properties that resemble those of platinum group metals, but at a lower cost. The materials obtained are expected to demonstrate catalytic activity in a series of hydrocarbon reactions involving hydrogen transfer. This project demonstrates the potential of carbon fiber composite monoliths as catalyst supports.

  17. CARBON FIBER COMPOSITES IN HIGH VOLUME

    Energy Technology Data Exchange (ETDEWEB)

    Warren, Charles David [ORNL; Das, Sujit [ORNL; Jeon, Dr. Saeil [Volvo Trucks North America

    2014-01-01

    Vehicle lightweighting represents one of several design approaches that automotive and heavy truck manufacturers are currently evaluating to improve fuel economy, lower emissions, and improve freight efficiency (tons-miles per gallon of fuel). With changes in fuel efficiency and environmental regulations in the area of transportation, the next decade will likely see considerable vehicle lightweighting throughout the ground transportation industry. Greater use of carbon fiber composites and light metals is a key component of that strategy. This paper examines the competition between candidate materials for lightweighting of heavy vehicles and passenger cars. A 53-component, 25 % mass reduction, body-in-white cost analysis is presented for each material class, highlighting the potential cost penalty for each kilogram of mass reduction and then comparing the various material options. Lastly, as the cost of carbon fiber is a major component of the elevated cost of carbon fiber composites, a brief look at the factors that influence that cost is presented.

  18. Functionally Graded Nanophase Beryllium/Carbon Composites

    Science.gov (United States)

    Choi, Michael K.

    2003-01-01

    Beryllium, beryllium alloys, beryllium carbide, and carbon are the ingredients of a class of nanophase Be/Be2C/C composite materials that can be formulated and functionally graded to suit a variety of applications. In a typical case, such a composite consists of a first layer of either pure beryllium or a beryllium alloy, a second layer of B2C, and a third layer of nanophase sintered carbon derived from fullerenes and nanotubes. The three layers are interconnected through interpenetrating spongelike structures. These Be/Be2C/C composite materials are similar to Co/WC/diamond functionally graded composite materials, except that (1) W and Co are replaced by Be and alloys thereof and (2) diamond is replaced by sintered carbon derived from fullerenes and nanotubes. (Optionally, one could form a Be/Be2C/diamond composite.) Because Be is lighter than W and Co, the present Be/Be2C/C composites weigh less than do the corresponding Co/WC/diamond composites. The nanophase carbon is almost as hard as diamond. WC/Co is the toughest material. It is widely used for drilling, digging, and machining. However, the fact that W is a heavy element (that is, has high atomic mass and mass density) makes W unattractive for applications in which weight is a severe disadvantage. Be is the lightest tough element, but its toughness is less than that of WC/Co alloy. Be strengthened by nanophase carbon is much tougher than pure or alloy Be. The nanophase carbon has an unsurpassed strength-to-weight ratio. The Be/Be2C/C composite materials are especially attractive for terrestrial and aerospace applications in which there are requirements for light weight along with the high strength and toughness of the denser Co/WC/diamond materials. These materials could be incorporated into diverse components, including cutting tools, bearings, rocket nozzles, and shields. Moreover, because Be and C are effective as neutron moderators, Be/Be2C/C composites could be attractive for some nuclear applications.

  19. Composite materials design and applications

    CERN Document Server

    Gay, Daniel; Tsai, Stephen W

    2002-01-01

    PART ONE. PRINCIPLES OF CONSTRUCTIONCOMPOSITE MATERIALS, INTEREST AND PROPERTIESWhat is Composite Material Fibers and MatrixWhat can be Made Using Composite Materials?Typical Examples of Interest on the Use of Composite MaterialsExamples on Replacing Conventional Solutions with CompositesPrincipal Physical PropertiesFABRICATION PROCESSESMolding ProcessesOther Forming ProcessesPractical Hints in the Manufacturing ProcessesPLY PROPERTIESIsotropy and AnisotropyCharacteristics of the Reinforcement-Matrix MixtureUnidirectional PlyWoven FabricsMats and Reinforced MatricesMultidimensional FabricsMetal Matrix CompositesTestsSANDWICH STRUCTURES:What is a Sandwich Structure?Simplified FlexureA Few Special AspectsFabrication and Design ProblemsNondestructive Quality ControlCONCEPTION AND DESIGNDesign of a Composite PieceThe LaminateFailure of LaminatesSizing of LaminatesJOINING AND ASSEMBLYRiveting and BoltingBondingInsertsCOMPOSITE MATERIALS AND AEROSPACE CONSTRUCTIONAircraftHelicoptersPropeller Blades for AirplanesTur...

  20. 碳纤维复合材料起毛辊的结构与制备%Structure and Preparation of Carbon Fiber Composite Materials Fluff Rolls

    Institute of Scientific and Technical Information of China (English)

    徐艳; 张伟明

    2014-01-01

    一种碳纤维复合材料起毛辊的结构与制备,包括起毛辊的辊体和装在辊体两端的轴头。首先,在设计好的模具芯棒上缠绕碳纤维预浸布,做成碳纤维内衬管备用;然后将轴头的粘接段涂上粘合剂后插入碳纤维内衬管内进行胶接;最后以碳纤维内衬管作为芯棒,再缠绕碳纤维预浸布,同时将轴头的加强轴肩包裹在内,以固化粗加工-精加工-涂装,最后制成成品起毛辊。其质量轻、直线度好、抗疲劳、刚性好,不仅碳纤维和树脂结合更好,致密度更高,强度也大大超过了一步法,延长了起毛辊的寿命。而且碳纤维复合材料和金属轴头通过两次包覆粘接,增大了碳纤维管壁与金属轴头的接触面,粘接更牢,大大提高了碳纤维复合材料起毛辊的整体强度。%Structure and preparation of a carbon fiber composite material pile roller, including a roller body and the pile roller mounted at both ends of the roller shaft head body. First, in the design of a mold mandrel wound carbon fiber prepreg, made of carbon fiber liner spare; then coated with adhesive segment axis head is inserted within the adhesive lined carbon fiber tube glued; Finally, carbon fiber lined pipe as a mandrel, and then wound carbon fiber prepreg, while the head of the shaft, including strengthening the shoulder wrap to cure roughing - finishing - painting, finally finished products pile roller. Its light weight, good straightness, anti-fatigue, rigid, carbon fiber and resin bonded not only better, higher density, strength greatly exceeds the one-step, extend the life of fluff roll. And carbon fiber composite materials and metal shaft head covered by two bonding, increases the contact surface of the carbon fiber wall with metal shaft head, bonding more firmly, greatly improving the overall strength of the carbon fiber composite material fluff roll.

  1. Multiscale anode materials in lithium ion batteries by combining micro- with nanoparticles: design of mesoporous TiO2 microfibers@nitrogen doped carbon composites.

    Science.gov (United States)

    Cheng, Wei; Rechberger, Felix; Primc, Darinka; Niederberger, Markus

    2015-09-07

    TiO2 has been considered as a promising anode material for lithium ion batteries. However, its poor rate capability originating from the intrinsically low lithium ion diffusivity and its poor electronic conductivity hampers putting such an application into practice. Both issues can be addressed by nanostructure engineering and conductive surface coating. Herein, we report a template-assisted synthesis of micron sized TiO2 fibers consisting of a mesoporous network of anatase nanoparticles of about 7.5 nm and coated by N doped carbon. In a first step, an amorphous layer of TiO2 was deposited on cobalt silicate nanobelts and subsequently transformed into crystalline anatase nanoparticles by hydrothermal treatment. The N doped carbon coating was realized by in situ polymerization of dopamine on the crystalline TiO2 followed by annealing under N2. After removal of the template, we obtained the final mesoporous TiO2 fibers@N doped carbon composite. Electrochemical tests revealed that the composite electrode exhibited excellent electrochemical properties in terms of specific capacity, rate performance and long term stability.

  2. A fundamental study on carbon composites of FeF3.0.33H2O as open-framework cathode materials for calcium-ion batteries

    Science.gov (United States)

    Murata, Yoshiaki; Minami, Ryoji; Takada, Shoki; Aoyanagi, Kengo; Tojo, Tomohiro; Inada, Ryoji; Sakurai, Yoji

    2017-01-01

    Carbon composites of open-framework iron fluoride (FeF3.0.33H2O/C) was investigated as a new cathode material for calcium ion batteries for the first time. FeF3.0.33H2O/C delivers a relatively large capacity of ca. 110mAhg-1. Its reversible capacity was greatly improved over non-composite FeF3.0.33H2O. During the first discharge and discharge-charge, insertion/extraction of Ca2+ into/from FeF3.0.33H2O/C were confirmed by an ex-situ X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectroscopy (EDX) analysis. From the ex-situ analysis results, it was confirmed that Ca2+ was inserted and extracted with redox of Fe.

  3. Epoxy based photoresist/carbon nanoparticle composites

    DEFF Research Database (Denmark)

    Lillemose, Michael; Gammelgaard, Lauge; Richter, Jacob;

    2008-01-01

    We have fabricated composites of SU-8 polymer and three different types of carbon nanoparticles (NPs) using ultrasonic mixing. Structures of composite thin films have been patterned on a characterization chip with standard UV photolithography. Using a four-point bending probe, a well defined stress...... is applied to the composite thin film and we have demonstrated that the composites are piezoresistive. Stable gauge factors of 5-9 have been measured, but we have also observed piezoresistive responses with gauge factors as high as 50. As SU-8 is much softer than silicon and the gauge factor of the composite...... material is relatively high, carbon nanoparticle doped SU-8 is a valid candidate for the piezoresistive readout in polymer based cantilever sensors, with potentially higher sensitivity than silicon based cantilevers....

  4. Damage detection in carbon composite material typical of wind turbine blades using auto-associative neural networks

    Science.gov (United States)

    Dervilis, N.; Barthorpe, R. J.; Antoniadou, I.; Staszewski, W. J.; Worden, K.

    2012-04-01

    The structure of a wind turbine blade plays a vital role in the mechanical and structural operation of the turbine. As new generations of offshore wind turbines are trying to achieve a leading role in the energy market, key challenges such as a reliable Structural Health Monitoring (SHM) of the blades is significant for the economic and structural efficiency of the wind energy. Fault diagnosis of wind turbine blades is a "grand challenge" due to their composite nature, weight and length. The damage detection procedure involves additional difficulties focused on aerodynamic loads, environmental conditions and gravitational loads. It will be shown that vibration dynamic response data combined with AANNs is a robust and powerful tool, offering on-line and real time damage prediction. In this study the features used for SHM are Frequency Response Functions (FRFs) acquired via experimental methods based on an LMS system by which identification of mode shapes and natural frequencies is accomplished. The methods used are statistical outlier analysis which allows a diagnosis of deviation from normality and an Auto-Associative Neural Network (AANN). Both of these techniques are trained by adopting the FRF data for normal and damage condition. The AANN is a method which has not yet been widely used in the condition monitoring of composite materials of blades. This paper is trying to introduce a new scheme for damage detection, localisation and severity assessment by adopting simple measurements such as FRFs and exploiting multilayer neural networks and outlier novelty detection.

  5. Fracture of Carbon Nanotube - Amorphous Carbon Composites: Molecular Modeling

    Science.gov (United States)

    Jensen, Benjamin D.; Wise, Kristopher E.; Odegard, Gregory M.

    2015-01-01

    Carbon nanotubes (CNTs) are promising candidates for use as reinforcements in next generation structural composite materials because of their extremely high specific stiffness and strength. They cannot, however, be viewed as simple replacements for carbon fibers because there are key differences between these materials in areas such as handling, processing, and matrix design. It is impossible to know for certain that CNT composites will represent a significant advance over carbon fiber composites before these various factors have been optimized, which is an extremely costly and time intensive process. This work attempts to place an upper bound on CNT composite mechanical properties by performing molecular dynamics simulations on idealized model systems with a reactive forcefield that permits modeling of both elastic deformations and fracture. Amorphous carbon (AC) was chosen for the matrix material in this work because of its structural simplicity and physical compatibility with the CNT fillers. It is also much stiffer and stronger than typical engineering polymer matrices. Three different arrangements of CNTs in the simulation cell have been investigated: a single-wall nanotube (SWNT) array, a multi-wall nanotube (MWNT) array, and a SWNT bundle system. The SWNT and MWNT array systems are clearly idealizations, but the SWNT bundle system is a step closer to real systems in which individual tubes aggregate into large assemblies. The effect of chemical crosslinking on composite properties is modeled by adding bonds between the CNTs and AC. The balance between weakening the CNTs and improving fiber-matrix load transfer is explored by systematically varying the extent of crosslinking. It is, of course, impossible to capture the full range of deformation and fracture processes that occur in real materials with even the largest atomistic molecular dynamics simulations. With this limitation in mind, the simulation results reported here provide a plausible upper limit on

  6. Erosion-resistant composite material

    Science.gov (United States)

    Finch, C.B.; Tennery, V.J.; Curlee, R.M.

    A highly erosion-resistant composite material is formed of chemical vapor-deposited titanium diboride on a sintered titanium diboride-nickel substrate. This material may be suitable for use in cutting tools, coal liquefaction systems, etc.

  7. Carbon nanotube suspensions, dispersions, & composites

    Science.gov (United States)

    Simmons, Trevor John

    Carbon Nanotubes (CNTs) are amazing structures that hold the potential to revolutionize many areas of scientific research. CNTs can be behave both as semiconductors and metals, can be grown in highly ordered arrays and patterns or in random orientation, and can be comprised of one graphene cylinder (single wall nanotube, SWNT) or several concentric graphene cylinders (multi-wall nanotube, MWNT). Although these structures are usually only a few nanometers wide, they can be grown up to centimeter lengths, and in massive quantities. CNTs can be produced in a variety of processes ranging from repeated combustion of organic material such as dried grass, arc-discharge with graphite electrodes, laser ablation of a graphitic target, to sophisticated chemical vapor deposition (CVD) techniques. CNTs are stronger than steel but lighter than aluminum, and can be more conductive than copper or semiconducting like silicon. This variety of properties has been matched by the wide variety of applications that have been developed for CNTs. Many of these applications have been limited by the inability of researchers to tame these structures, and incorporating CNTs into existing technologies can be exceedingly difficult and prohibitively expensive. It is therefore the aim of the current study to develop strategies for the solution processing and deposition of CNTs and CNT-composites, which will enable the use of CNTs in existing and emerging technologies. CNTs are not easily suspended in polar solvents and are extremely hydrophobic materials, which has limited much of the solution processing to organic solvents, which also cannot afford high quality dispersions of CNTs. The current study has developed a variety of aqueous CNT solutions that employ surfactants, water-soluble polymers, or both to create suspensions of CNTs. These CNT 'ink' solutions were deposited with a variety of techniques that have afforded many interesting structures, both randomly oriented as well as highly

  8. Mathematical models of carbon-carbon composite deformation

    Science.gov (United States)

    Golovin, N. N.; Kuvyrkin, G. N.

    2016-09-01

    Mathematical models of carbon-carbon composites (CCC) intended for describing the processes of deformation of structures produced by using CCC under high-temperature loading are considered. A phenomenological theory of CCC inelastic deformation is proposed, where such materials are considered as homogeneous ones with effective characteristics and where their high anisotropy of mechanical characteristics and different ways of resistance to extension and compression are taken into account. Micromechanical models are proposed for spatially reinforced CCC, where the difference between mechanical characteristics of components and the reinforcement scheme are taken into account. Themodel parameters are determined from the results of experiments of composite macrospecimens in the directions typical of the material. A version of endochronictype theory with several internal times "launched" for each composite component and related to some damage accumulation mechanisms is proposed for describing the inelastic deformation. Some practical examples are considered.

  9. Composite Materials for Structural Design.

    Science.gov (United States)

    1982-03-01

    Introduction to Composite Materials , Technomic, Westport, Connecticut, 1980, pp. 19-20, 388-401. 8. W.D. Bascom, J.L. Bitner, R.J. Moulton, and A.R. Siebert...34 Introduction to Composite Materials ", Technomic Publishing Co., pp. 8-18,(1980). [6] Beckwith, S. W., "Viscoelastic Characterization of a Nonlinear Glass

  10. Composite Materials in Overhead Lines

    DEFF Research Database (Denmark)

    Sørensen, Thomas Kjærsgaard; Holbøll, Joachim

    2009-01-01

    with respect to solved and persisting known failures/problems of both mechanical and electrical nature. Major challenges related to extensive use of composite materials in an overhead line system are identified, as are possible benefits - both when using standard as well as customised composite components, e......The use of composite materials, e.g. fibreglass materials, in overhead transmission line systems is nothing new. Composite based insulators have been applied to transmission lines for over 30 years, mainly as suspension and post insulators and often as an option for special applications. Also...... towers and recently conductors based on composite materials are available at transmission levels. In this paper it is investigated which composite based solutions are available in connection with complete overhead line systems including insulators, towers and conductors. The components are reviewed...

  11. Superconducting composites materials. Materiaux composites supraconducteurs

    Energy Technology Data Exchange (ETDEWEB)

    Kerjouan, P.; Boterel, F.; Lostec, J.; Bertot, J.P.; Haussonne, J.M. (Centre National d' Etudes des Telecommunications (CNET), 22 - Lannion (FR))

    1991-11-01

    The new superconductor materials with a high critical current own a large importance as well in the electronic components or in the electrotechnical devices fields. The deposit of such materials with the thick films technology is to be more and more developed in the years to come. Therefore, we tried to realize such thick films screen printed on alumina, and composed mainly of the YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} material. We first realized a composite material glass/YBa{sub 2}Cu{sub 3}O{sub 7-{delta}}, by analogy with the classical screen-printed inks where the glass ensures the bonding with the substrate. We thus realized different materials by using some different classes of glass. These materials owned a superconducting transition close to the one of the pure YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} material. We made a slurry with the most significant composite materials and binders, and screen-printed them on an alumina substrate preliminary or not coated with a diffusion barrier layer. After firing, we studied the thick films adhesion, the alumina/glass/composite material interfaces, and their superconducting properties. 8 refs.; 14 figs.; 9 tabs.

  12. Multifunctional Carbon Fibre Tapes for Automotive Composites

    Science.gov (United States)

    Koncherry, V.; Potluri, P.; Fernando, A.

    2016-11-01

    Cabon fibre composites are used where mechanical performance such as strength, stiffness and impact properties at low density is a critical parameter for engineering applications. Carbon fibre flat tape is one material which is traditionally used to manufacture three-dimensional composites in this area. Modifying the carbon fibre tape to incorporate other functions such as stealth, electromagnetic interference, shielding, de-icing, self-repair, energy storage, allows us to create multi-functional carbon fibre tape. Researchers have been developing such material and the technology for their manufacture in order to produce multifunctional carbon fibre based components more economically and efficiently. This paper presents the manufacturing process of a metallised carbon fibre material for a chopped fibre preforming process that uses electromagnets for preforming instead of traditional suction airflow fibre deposition. In addition, the paper further presents mechanical and magneto-static modelling that is carried out to investigate the bending properties of the material produced and its suitability for creating 3D preforms.

  13. 碳纤维复合材料强度的有限元模拟%FINITE ELEMENT SIMULATION FOR THE STRENGTH OF CARBON FIBRE COMPOSITE MATERIAL

    Institute of Scientific and Technical Information of China (English)

    李玮; 段成红; 吴祥

    2011-01-01

    Carbon fibre composite materials are more and more used in industries, but the research on the properties is not deep enough. To save test cost, it is necessary to carry out theoretical simulation for the materials while performing experimental investigation. In this paper, ultimate strength of a carbon fibre composite material with a standard testing NOL-ring was calculated numerically by using ANSYS software with two simulation methods,namely node coupling and contacting. Circumferential stresses along the NOL-ring were given. Results show that errors between the two simulations and the test results are 23.6% and 5.6% respectively, indicating that using contacting method is more precise.%碳纤维复合材料在工业上的应用越来越广,但对其材料性质的研究还远不充分.为了节省试验经费,应在进行必要试验的同时对碳纤维复合材料的性质进行模拟计算.本文针对一标准试验,利用ANSYS软件的节点耦合技术和接触分析技术分别对某碳纤维复合材料制成的NOL环进行了拉伸破坏载荷下的强度计算,给出NOL环上各点的周向应力.结果发现,这两种模拟方法与试验值的误差分别为23.6%和5.6%,表明接触分析技术比较精确.

  14. Engineering carbon materials from the hydrothermal carbonization process of biomass.

    Science.gov (United States)

    Hu, Bo; Wang, Kan; Wu, Liheng; Yu, Shu-Hong; Antonietti, Markus; Titirici, Maria-Magdalena

    2010-02-16

    Energy shortage, environmental crisis, and developing customer demands have driven people to find facile, low-cost, environmentally friendly, and nontoxic routes to produce novel functional materials that can be commercialized in the near future. Amongst various techniques, the hydrothermal carbonization (HTC) process of biomass (either of isolated carbohydrates or crude plants) is a promising candidate for the synthesis of novel carbon-based materials with a wide variety of potential applications. In this Review, we will discuss various synthetic routes towards such novel carbon-based materials or composites via the HTC process of biomass. Furthermore, factors that influence the carbonization process will be analyzed and the special chemical/physical properties of the final products will be discussed. Despite the lack of a clear mechanism, these novel carbonaceous materials have already shown promising applications in many fields such as carbon fixation, water purification, fuel cell catalysis, energy storage, CO(2) sequestration, bioimaging, drug delivery, and gas sensors. Some of the most promising examples will also be discussed here, demonstrating that the HTC process can rationally design a rich family of carbonaceous and hybrid functional carbon materials with important applications in a sustainable fashion.

  15. Mechanics in Composite Materials and Process

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dae Gil

    1993-03-15

    This book includes introduction of composite materials, stress, in-plane stiffness of laminates strain rate, ply stress, failure criterion and bending, composite materials micromechanics, composite plates and micromechanics of composite materials. It also deals with process of composite materials such as autoclave vacuum bag degassing process, connection of composite materials, filament winding process, resin transfer molding, sheet molding compound and compression molding.

  16. Heat Treated Carbon Fiber Material Selection Database

    Science.gov (United States)

    Effinger, M.; Patel, B.; Koenig, J.

    2008-01-01

    Carbon fibers are used in a variety high temperature applications and materials. However, one limiting factor in their transition into additional applications is an understanding of their functional properties during component processing and function. The requirements on the fibers are governed by the nature of the materials and the environments in which they will be used. The current carbon fiber vendor literature is geared toward the polymeric composite industry and not the ceramic composite industry. Thus, selection of carbon fibers is difficult, since their properties change as a function of heat treatment, processing or component operational temperature, which ever is greatest. To enable proper decisions to be made, a program was established wherein multiple fibers were selected and heat treated at different temperatures. The fibers were then examined for their physical and mechanical properties which are reported herein.

  17. Material Flows and Carbon Cycles

    Science.gov (United States)

    Worrell, E.

    2003-12-01

    The industrial sector emits almost 43 percent of the global anthropogenic carbon dioxide emissions to produce materials and products. Furthermore, energy is used to move materials and products and process the waste. Hence, a large amount of energy is consumed and CO2 is emitted to sustain our materials system. Until recently, studies investigating mitigation options focused on changes in the energy system. For industrial processes most studies evaluate how the current materials system can be maintained producing fewer greenhouse gas emissions. Three elements of a strategy to improve the long-term materials productivity are the reduction of dissipative uses of non-biodegradable materials, secondly, the re-design of products to use less material or design for re-use or recycling, and thirdly, develop more efficient technologies for material conversion and recycling. This will reduce or eliminate the need to extract virgin materials from the environment, and reduce CO2 emissions from the energy-intensive production processes. To assess measures to reduce materials consumption, fossil fuels consumption and CO2 emissions, detailed understanding of the material system is needed. The lifecycle of materials has to be investigated including all branches of industry with all the inputs and outputs. We start with a discussion of materials and the carbon cycle focusing on the contribution of materials to anthropogenic carbon flows. We discuss CO2 emissions from energy use in materials extraction and production, fossil (e.g. plastics) and biomass carbon (e.g. lumber, paper) used as feedstock of materials, and mineral sources (e.g. cement). We discuss opportunities to reduce CO2 emissions by improving the efficiency with which society uses materials through product design, material substitution, product reuse and material recycling.

  18. Electrochemical horseradish peroxidase biosensor based on dextran-ionic liquid-V{sub 2}O{sub 5} nanobelt composite material modified carbon ionic liquid electrode

    Energy Technology Data Exchange (ETDEWEB)

    Zhu Zhihong [Institute of Nano-Science and Technology Center, Huazhong Normal University, Wuhan 430079 (China); Sun Xiaoying; Wang Yan [College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, 53 Zhenzhou Road, Qingdao 266042 (China); Zeng Yan [Institute of Nano-Science and Technology Center, Huazhong Normal University, Wuhan 430079 (China); Sun Wei, E-mail: sunwei_1975@public.qd.sd.cn [College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, 53 Zhenzhou Road, Qingdao 266042 (China); Huang Xintang [Institute of Nano-Science and Technology Center, Huazhong Normal University, Wuhan 430079 (China)

    2010-11-01

    Direct electrochemistry of horseradish peroxidase (HRP) was realized in a dextran (De), 1-ethyl-3-methylimidazolium ethylsulphate ([EMIM]EtOSO{sub 3}) and V{sub 2}O{sub 5} nanobelt composite material modified carbon ionic liquid electrode (CILE). Spectroscopic results indicated that HRP retained its native structure in the composite. A pair of well-defined redox peaks of HRP appeared in pH 3.0 phosphate buffer solution with the formal potential of -0.213 V (vs. SCE), which was the characteristic of HRP heme Fe(III)/Fe(II) redox couple. The result was attributed to the specific characteristics of De-IL-V{sub 2}O{sub 5} nanocomposite and CILE, which promoted the direct electron transfer rate of HRP with electrode. The electrochemical parameters of HRP on the composite modified electrode were calculated and the electrocatalysis of HRP to the reduction of trichloroacetic acid (TCA) was examined. Under the optimal conditions the reduction peak current increased with TCA concentration in the range from 0.4 to 16.0 mmol L{sup -1}. The proposed electrode is valuable for the third-generation electrochemical biosensor.

  19. Applications for carbon fibre recovered from composites

    Science.gov (United States)

    Pickering; Liu, Z.; Turner, TA; Wong, KH

    2016-07-01

    Commercial operations to recover carbon fibre from waste composites are now developing and as more recovered fibre becomes available new applications for recovered fibre are required. Opportunities to use recovered carbon fibre as a structural reinforcement are considered involving the use of wet lay processes to produce nonwoven mats. Mats with random in-plane fibre orientation can readily be produced using existing commercial processes. However, the fibre volume fraction, and hence the mechanical properties that can be achieved, result in composites with limited mechanical properties. Fibre volume fractions of 40% can be achieved with high moulding pressures of over 100 bar, however, moulding at these pressures results in substantial fibre breakage which reduces the mean fibre length and the properties of the composite manufactured. Nonwoven mats made from aligned, short carbon fibres can achieve higher fibre volume fractions with lower fibre breakage even at high moulding pressure. A process for aligning short fibres is described and a composite of over 60% fibre volume fraction has been manufactured at a pressures up to 100 bar with low fibre breakage. Further developments of the alignment process have been undertaken and a composite of 46% fibre volume fraction has been produced moulded at a pressure of 7 bar in an autoclave, exhibiting good mechanical properties that compete with higher grade materials. This demonstrates the potential for high value applications for recovered carbon fibre by fibre alignment.

  20. Advanced biomaterials from renewable resources: An investigation on cellulose nanocrystal composites and carbon dioxide extraction of rendered materials

    Science.gov (United States)

    Orellana, Jose Luis

    The annual global consumption of petroleum-based plastics is approximately 280 million tons and is impacting the sustainability of our planet and prosperity of future generations. One solution is the development of bio-based polymer materials with advanced properties for commercial applications. Therefore, the ultimate goal of this dissertation is to investigate the properties of new bio-based materials for broader applications. This dissertation includes two research areas: cellulose nanocomposites, and CO2 extractions of rendered fat. In the first half, cellulose nanocrystals (CNCs), which exhibit excellent mechanical and optical properties, were investigated for the reinforcement of a biodegradable polymer. The properties of these nanocomposites were studied to intellectually contribute to the understanding of the reinforcement mechanisms of CNC nanocomposites. In the second half, a more efficient and greener extraction of fat from rendered materials (RMs) was explored to broaden their potential applications, which include protein-based polymers and biofuels. Since CNCs are hydrophilic, surface modification with various surfactants was first accomplished in this research, increasing the dispersion stability in non-polar solvents by at least a month. Only 1 wt.% of surfactant with respect to CNCs was needed to afford a significant increase in the CNC stability, representing a much lower percentage than the values reported in the literature. Moreover, these CNCs showed the ability to selfassemble into local liquid crystal structures, a potential advantage for polymer reinforcement. CNCs were subsequently investigated as an additive for polylactic acid (PLA), which is the most widely used synthetic biopolymer in the market. CNC addition yielded a 61% increase in toughness at 1 wt.% CNC load. The tensile strength and modulus were not affected by the CNC addition, addressing one of the most frequent issues in the toughening of polymers. In addition, polarized

  1. Heat-Resistant Composite Materials Based on Polyimide Matrix

    Directory of Open Access Journals (Sweden)

    Vitaly Sergeyevich Ivanov

    2016-12-01

    Full Text Available Heat-resistant composite materials with a polyimide-based binder were obtained in this paper. Composites were prepared with different content of single-wall carbon nanotubes (SWCNT and nanostructured silicon carbide, and polyimides coated carbon fibers woven into the cloth. Composite materials showed high values of thermostability and resistance to thermo-oxidative degradation, as well as good mechanical properties.

  2. Dry Process for Manufacturing Hybridized Boron Fiber/Carbon Fiber Thermoplastic Composite Materials from a Solution Coated Precursor

    Science.gov (United States)

    Belvin, Harry L. (Inventor); Cano, Roberto J. (Inventor)

    2003-01-01

    An apparatus for producing a hybrid boron reinforced polymer matrix composite from precursor tape and a linear array of boron fibers. The boron fibers are applied onto the precursor tapes and the precursor tape processed within a processing component having an impregnation bar assembly. After passing through variable-dimension forming nip-rollers, the precursor tape with the boron fibers becomes a hybrid boron reinforced polymer matrix composite. A driving mechanism is used to pulled the precursor tape through the method and a take-up spool is used to collect the formed hybrid boron reinforced polymer matrix composite.

  3. Material Modelling - Composite Approach

    DEFF Research Database (Denmark)

    Nielsen, Lauge Fuglsang

    1997-01-01

    , and internal stresses caused by drying shrinkage with experimental results reported in the literature on the mechanical behavior of mature concretes. It is then concluded that the model presented applied in general with respect to age at loading.From a stress analysis point of view the most important finding......This report is part of a research project on "Control of Early Age Cracking" - which, in turn, is part of the major research programme, "High Performance Concrete - The Contractor's Technology (HETEK)", coordinated by the Danish Road Directorate, Copenhagen, Denmark, 1997.A composite......-rheological model of concrete is presented by which consistent predictions of creep, relaxation, and internal stresses can be made from known concrete composition, age at loading, and climatic conditions. No other existing "creep prediction method" offers these possibilities in one approach.The model...

  4. Carbon materials for supercapacitors

    Science.gov (United States)

    Gao, Yang

    As an important energy storage device, electrochemical supercapacitors or ultracapacitors fill the gap between conventional dielectric capacitors and batteries in terms of specific energy and power. Although supercapacitors have been used in electric vehicles, digital communication instruments, and pulsed lasers, further improvement of supercapacitor performance is highly needed to enhance the energy density without significantly losing the power density. Additionally, the conventional supercapacitors use rigid packages and liquid electrolytes, which limit applications in transparent and flexible electronics. To address these challenges, the research efforts in this dissertation mainly focused on: 1) improvement of the energy density of carbon nanoonions by chemical activation; 2) laser-assisted activation of carbon nanotubes for improved energy density; 3) fabrication of flexible solid-state supercapacitors based on nanocarbon and manganese dioxide (MnO2) hybrid electrodes; and 4) investigation of the electrochemical performance of graphene as transparent and flexible supercapacitor electrodes.

  5. Nanographene reinforced carbon/carbon composites

    Science.gov (United States)

    Bansal, Dhruv

    Carbon/Carbon Composites (CCC) are made of carbon reinforcement in carbon matrix and have high thermal stability and fatigue resistance. CCC are used in nose cones, heat shields and disc brakes of aircrafts due to their exceptional mechanical properties at high temperature. The manufacturing process of CCC involves a carbonization stage in which unwanted elements, except carbon, are eliminated from the polymer precursor. Carbonization results in the formation of voids and cracks due to the thermal mismatch between the reinforcement and the matrix and expulsion of volatiles from the polymer matrix. Thermal cracks and voids decrease the density and mechanical properties of the manufactured CCC. In this work, Nanographene Platelets (NGP) were explored as nanofillers to fill the voids/cracks and reduce thermal shrinkage in CCC. They were first compared with Vapor Grown Carbon Nanofibers (VGCNF) by dispersion of different concentrations (0.5wt%, 1.5wt%, 3wt%) in resole-type phenolic resin and were characterized to explore their effect on rheology, heat of reaction and wetting behavior. The dispersions were then cured to form nanocomposites and were characterized for morphology, flexure and thermal properties. Finally, NGP were introduced into the carbon/carboncomposites in two stages, first by spraying in different concentrations (0.5wt%, 1.5wt%, 3wt%, 5wt %) during the prepreg formation and later during densification by directly mixing in the corresponding densification mix. The manufactured NGP reinforced CCC were characterized for microstructure, porosity, bulk density and mechanical properties (Flexure and ILSS) which were further cross-checked by non-destructive techniques (vibration and ultrasonic). In this study, it was further found that at low concentration (≤ 1.5 wt%) NGP were more effective in increasing the heat of reaction and in decreasing the viscosity of the phenolic resin. The decrease in viscosity led to better wetting properties of NGP / phenolic

  6. Carbon Materials Research

    Science.gov (United States)

    2006-08-01

    electrodes, high temperature molds, rocket nozzles and exit cones, tires , ink, nuclear reactors and fuel particles, filters, prosthetics, batteries and...carbon would be highly oriented pyrolytic graphite (HOPG), which is formed by depositing one atom at a time on a surface utilizing the pyrolysis of a...Moreover, it is well known that during pyrolysis , mesophase converts into a matrix that is very anisotropic. The formation of onion-like “sheaths

  7. Integration of Carbon Fiber Composite Materials into Air-Cooled Reciprocating Piston Engines for UA V Applications

    Science.gov (United States)

    2012-05-04

    Composite MMC: …………………...………..Metal Matrix Composite OHC: …………………...………...Overhead Camshaft ...chosen as the test platform because it is inexpensive, air-cooled (similar to UAV engines), and uses an overhead camshaft (OHC) design which...facilitated the design of the crankcase. An OHC design avoids the necessity to align the camshaft as well as. Extending this study to a diesel engine would

  8. Materials for carbon dioxide separation

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Qingqing

    2014-10-01

    The CO{sub 2} adsorption capacities at room temperature have been investigated by comparing carbon nanotubes, fullerene, graphenes, graphite and granular activated carbons. It turned out that the amount of the micropore surface area was dominating the CO{sub 2} adsorption ability. Another promising class of materials for CO{sub 2} capture and separation are CaO derived from the eggshells. Two aspects were studied in present work: a new hybrid materials synthesized by doping the CaTiO{sub 3} and the relationship between physisorption and chemisorption properties of CaO-based materials.

  9. Sulfur/graphitic hollow carbon sphere nano-composite as a cathode material for high-power lithium-sulfur battery.

    Science.gov (United States)

    Shin, Eon Sung; Kim, Min-Seop; Cho, Won Il; Oh, Si Hyoung

    2013-08-03

    The intrinsic low conductivity of sulfur which leads to a low performance at a high current rate is one of the most limiting factors for the commercialization of lithium-sulfur battery. Here, we present an easy and convenient method to synthesize a mono-dispersed hollow carbon sphere with a thin graphitic wall which can be utilized as a support with a good electrical conductivity for the preparation of sulfur/carbon nano-composite cathode. The hollow carbon sphere was prepared from the pyrolysis of the homogenous mixture of the mono-dispersed spherical silica and Fe-phthalocyanine powder in elevated temperature. The composite cathode was manufactured by infiltrating sulfur melt into the inner side of the graphitic wall. The electrochemical cycling shows a capacity of 425 mAh g-1 at 3 C current rate which is more than five times larger than that for the sulfur/carbon black nano-composite prepared by simple ball milling.

  10. Carbon fiber-reinforced carbon as a potential implant material.

    Science.gov (United States)

    Adams, D; Williams, D F; Hill, J

    1978-01-01

    A carbon fiber-reinforced carbon is being evaluated as a promising implant material. In a unidirectional composite, high strengths (1200 MN/m2 longitudinal flexural strength) and high modulus (140 GN/m2 flexural modulus) may be obtained with an interlaminar shear strength of 18 MN/m2. Alternatively, layers of fibers may be laid in two directions to give more isotopic properties. The compatibility of the material with bone has been studied by implanting specimens in holes drilled in rat femora. For a period of up to 8 weeks, a thin layer of fibrous tissue bridged the gap between bone and implant; but this tissue mineralizes and by 10 weeks, bone can be observed adjacent to the implant, giving firm fixation. Potential applications include endosseous dental implants where a greater strength in the neck than that provided by unreinforced carbon would be advantageous.

  11. Computational simulation of a diffusion process of carbon nanotubes in aluminium to improve the mechanical properties of a composite material

    Science.gov (United States)

    Suárez Guerrero, G.; Valencia-García, M. F.; Martínez Tejada, H. V.; Toro Cadavid, O. J.

    2017-01-01

    A computational thermo-mechanical insertion model was implemented considering the incorporation of carbon nanotubes (CNTs) into semisolid aluminium. A shell surface of CNTs within an aluminium matrix was obtained using the Particles Dynamic Method (PDM). Also, energy absorption simulations were performed through computational impact tests in order to characterize the behaviour of the nanocomposite under high strain rates. Theoretical results are useful in the design of nanocomposites and the experimental processing of Al/CNTs nanocomposites for different applications.

  12. Thermal Conductivity of Carbon Nanotube Composite Films

    Science.gov (United States)

    Ngo, Quoc; Cruden, Brett A.; Cassell, Alan M.; Walker, Megan D.; Koehne, Jessica E.; Meyyappan, M.; Li, Jun; Yang, Cary Y.

    2004-01-01

    State-of-the-art ICs for microprocessors routinely dissipate power densities on the order of 50 W/sq cm. This large power is due to the localized heating of ICs operating at high frequencies, and must be managed for future high-frequency microelectronic applications. Our approach involves finding new and efficient thermally conductive materials. Exploiting carbon nanotube (CNT) films and composites for their superior axial thermal conductance properties has the potential for such an application requiring efficient heat transfer. In this work, we present thermal contact resistance measurement results for CNT and CNT-Cu composite films. It is shown that Cu-filled CNT arrays enhance thermal conductance when compared to as-grown CNT arrays. Furthermore, the CNT-Cu composite material provides a mechanically robust alternative to current IC packaging technology.

  13. Natural materials for carbon capture.

    Energy Technology Data Exchange (ETDEWEB)

    Myshakin, Evgeniy M. (National Energy Technology Laboratory, Pittsburgh, PA); Romanov, Vyacheslav N. (National Energy Technology Laboratory, Pittsburgh, PA); Cygan, Randall Timothy

    2010-11-01

    Naturally occurring clay minerals provide a distinctive material for carbon capture and carbon dioxide sequestration. Swelling clay minerals, such as the smectite variety, possess an aluminosilicate structure that is controlled by low-charge layers that readily expand to accommodate water molecules and, potentially, carbon dioxide. Recent experimental studies have demonstrated the efficacy of intercalating carbon dioxide in the interlayer of layered clays but little is known about the molecular mechanisms of the process and the extent of carbon capture as a function of clay charge and structure. A series of molecular dynamics simulations and vibrational analyses have been completed to assess the molecular interactions associated with incorporation of CO2 in the interlayer of montmorillonite clay and to help validate the models with experimental observation.

  14. Aerogel and xerogel composites for use as carbon anodes

    Science.gov (United States)

    Cooper, John F.; Tillotson, Thomas M.; Hrubesh, Lawrence W.

    2008-08-12

    Disclosed herein are aerogel and xerogel composite materials suitable for use as anodes in fuel cells and batteries. Precursors to the aerogel and xerogel compounds are infused with inorganic polymeric materials or carbon particles and then gelled. The gels are then pyrolyzed to form composites with internal structural support.

  15. Scalable synthesis of core-shell structured SiOx/nitrogen-doped carbon composite as a high-performance anode material for lithium-ion batteries

    Science.gov (United States)

    Shi, Lu; Wang, Weikun; Wang, Anbang; Yuan, Keguo; Jin, Zhaoqing; Yang, Yusheng

    2016-06-01

    In this work, a novel core-shell structured SiOx/nitrogen-doped carbon composite has been prepared by simply dispersing the SiOx particles, which are synthesized by a thermal evaporation method from an equimolar mixture of Si and SiO2, into the dopamine solution, followed by a carbonization process. The SiOx core is well covered by the conformal and homogeneous nitrogen-doped carbon layer from the pyrolysis of polydopamine. By contrast with the bare SiOx, the electrochemical performance of the as-prepared core-shell structured SiOx/nitrogen-doped carbon composite has been improved significantly. It delivers a reversible capacity of 1514 mA h g-1 after 100 cycles at a current density of 100 mA g-1 and 933 mA h g-1 at 2 A g-1, much higher than those of commercial graphite anodes. The nitrogen-doped carbon layer ensures the excellent electrochemical performance of the SiOx/C composite. In addition, since dopamine can self-polymerize and coat virtually any surface, this versatile, facile and highly efficient coating process may be widely applicable to obtain various composites with uniform nitrogen-doped carbon coating layer.

  16. Thermal diffusivity mapping of 4D carbon-carbon composites

    Energy Technology Data Exchange (ETDEWEB)

    Wang, H.; Dinwiddie, R.B.

    1997-03-01

    High resolution, 2-D thermal diffusivity maps of carbon-carbon composites were obtained by a state-of-the-art infrared thermal imaging system. Unlike the traditional single-point IR detector used for thermal diffusivity measurements, the IR camera is capable of capturing images in its 256 x 256 pixel Focal Plane Array detector in a snap-shot mode. The camera takes up to 200 images at a rate of 120 frames/second. The temperature resolution of the Ir camera is 0.015 C and the spatial resolution is 20 {micro}m. Thermal diffusivity was calculated for each pixel. Four-direction carbon-carbon composites were used for the thermal diffusivity mapping study. The fiber bundles along the heat flow direction were found to have 25% higher diffusivity values than the surrounding matrix. The diffusivity map also showed detailed local variations in diffusivity which were impossible to measure using a single-point detector. Accurate diffusivity maps are very important to the design of composite materials.

  17. Composite materials for polymer electrolyte membrane microbial fuel cells.

    Science.gov (United States)

    Antolini, Ermete

    2015-07-15

    Recently, the feasibility of using composite metal-carbon, metal-polymer, polymer-carbon, polymer-polymer and carbon-carbon materials in microbial fuel cells (MFCs) has been investigated. These materials have been tested as MFC anode catalyst (microorganism) supports, cathode catalysts and membranes. These hybrid materials, possessing the properties of each component, or even with a synergistic effect, would present improved characteristics with respect to the bare components. In this paper we present an overview of the use of these composite materials in microbial fuel cells. The characteristics of the composite materials as well as their effect on MFC performance were compared with those of the individual component and/or the conventionally used materials.

  18. Mechanical Spectroscopy of Nanostructured Composite Materials

    Energy Technology Data Exchange (ETDEWEB)

    Mari, Daniele; Schaller, Robert; Mazaheri, Mehdi, E-mail: daniele.mari@epfl.ch [Ecole Polytechnique Federale de Lausanne, Laboratoire de Physique de la Matiere Complexe, Groupe de Spectroscopie Mecanique, CH-1015 Lausanne (Switzerland)

    2011-07-06

    The thermo-mechanical behavior of different nano-structured composite materials, which were processed within the SAPHIR European Integrated Project, has been characterized by mechanical spectroscopy. The obtained results show clearly that creep resistance of fine grain ceramics such as zirconia can be improved by carbon nano-tube (CNT) reinforcements. On the other hand the elastic modulus and the damping capacity of aluminum matrix composites were increased by SiC nano-particle additions. It has also been observed that CNT additions are responsible for a better thermal stability of polymer such as ABS (Acrylonitrile-Butadiene-Styrene) used in automotive industry.

  19. Energy-related application of composite material. Carbon fiber reinforced plastics (CFRP); Enerugi kanren yoto to CFRP

    Energy Technology Data Exchange (ETDEWEB)

    Higuchi, T. [Toray Industries, Tokyo (Japan)

    2000-01-15

    Carbon fiber reinforced plastics (CFRP) with advantages such as high strength, high relative elastic modulus, high chemical stability, and excellent thermal/electric properties, is widely used in aviation/space, sports, and industries. This paper takes up CNG tank, flywheel, and windmill blade, as examples of energy-related application development. For the purpose of weight reduction of CNG car, big three car manufacturers of the U.S. and Honda adopted CNG tank. Flywheel with CFRP rotor can store 3.8 times energy compared with that of steel. Windmill blade used in windmill power generation is mostly made of 3 blades and presently GFRP is used, but CFRP will become a main stream when the windmill is scaled up. In the future, it is necessary to reduce the cost of carbon fiber and its treatment process, as well as to solve the targets such as standardization of design, recognition by users, and verification in environmental use, and to develop further applications. (NEDO)

  20. Carbon-fiber composite molecular sieves for gas separation

    Energy Technology Data Exchange (ETDEWEB)

    Jagtoyen, M.; Derbyshire, F.; Kimber, G.; Fei, Y.Q. [Univ. of Kentucky Center for Applied Energy Research, Lexington, KY (United States)

    1995-08-01

    The progress of research in the development of novel, rigid, monolithic adsorbent carbon fiber composites is described. Carbon fiber composites are produced at ORNL and activated at the CAER using steam or CO{sub 2} under different conditions, with the aims of producing a uniform degree of activation through the material, and of closely controlling pore structure and adsorptive properties The principal focus of the work to date has been to produce materials with narrow porosity for use in gas separations.

  1. Controlled thermal sintering of a metal-metal oxide-carbon ternary composite with a multi-scale hollow nanostructure for use as an anode material in Li-ion batteries.

    Science.gov (United States)

    Kim, Hwan Jin; Zhang, Kan; Choi, Jae-Man; Song, Min Sang; Park, Jong Hyeok

    2014-03-11

    We report a synthetic scheme for preparing a SnO2-Sn-carbon triad inverse opal porous material using the controlled sintering of Sn precursor-infiltrated polystyrene (PS) nanobead films. Because the uniform PS nanobead film, which can be converted into carbon via a sintering step, uptakes the precursor solution, the carbon can be uniformly distributed throughout the Sn-based anode material. Moreover, the partial carbonization of the PS nanobeads under a controlled Ar/oxygen environment not only produces a composite material with an inverse opal-like porous nanostructure but also converts the Sn precursor/PS into a SnO2-Sn-C triad electrode.

  2. CARBON-CONTAINING COMPOSITES BASED ON METALS

    Directory of Open Access Journals (Sweden)

    VAGANOV V. E.

    2015-10-01

    Full Text Available Problem statement Among the developed technologies metal-composites production,a special place takes powder metallurgy, having fundamental differences from conventionally used foundry technologies. The main advantages of this technology are: the possibility of sensitive control, the structure and phase composition of the starting components, and ultimately the possibility of obtaining of bulk material in nanostructured state with a minimum of processing steps. The potential reinforcers metals include micro and nano-sized oxides, carbides, nitrides, whiskers. The special position is occupied with carbon nanostructures (CNS: С60 fullerenes, single-layer and multi-layer nanotubes, onions (spherical "bulbs", nano-diamonds and graphite,their properties are being intensively studied in recent years. These objects have a high thermal and electrical conductivity values, superelasticity, and have a strength approximate to the theoretical value, which can provide an obtaining composite nanomaterial with a unique set of physical and mechanical properties. In creation of a metal matrix composite nanomaterials (CM, reinforced by various CNS, a special attention should be given to mechanical activation processes (MA already at the stage of preparation of the starting components affecting the structure, phase composition and properties of aluminum-matrix composites. Purpose. To investigate the influence of mechanical activation on the structure and phase composition of aluminum-matrix composites. Conclusion. The results of the study of the structure and phase composition of the initial and mechanically activated powders and bulk-modified metal-composites are shown, depending on the type and concentration of modifying varieties CNS, regimes of MA and parameters of compaction. The study is conducted of tribological properties of Al-CNS OF nanostructured materials.

  3. Activated Carbon Composites for Air Separation

    Energy Technology Data Exchange (ETDEWEB)

    Contescu, Cristian I [ORNL; Baker, Frederick S [ORNL; Tsouris, Costas [ORNL; McFarlane, Joanna [ORNL

    2008-03-01

    In continuation of the development of composite materials for air separation based on molecular sieving properties and magnetic fields effects, several molecular sieve materials were tested in a flow system, and the effects of temperature, flow conditions, and magnetic fields were investigated. New carbon materials adsorbents, with and without pre-loaded super-paramagnetic nanoparticles of Fe3O4 were synthesized; all materials were packed in chromatographic type columns which were placed between the poles of a high intensity, water-cooled, magnet (1.5 Tesla). In order to verify the existence of magnetodesorption effect, separation tests were conducted by injecting controlled volumes of air in a flow of inert gas, while the magnetic field was switched on and off. Gas composition downstream the column was analyzed by gas chromatography and by mass spectrometry. Under the conditions employed, the tests confirmed that N2 - O2 separation occurred at various degrees, depending on material's intrinsic properties, temperature and flow rate. The effect of magnetic fields, reported previously for static conditions, was not confirmed in the flow system. The best separation was obtained for zeolite 13X at sub-ambient temperatures. Future directions for the project include evaluation of a combined system, comprising carbon and zeolite molecular sieves, and testing the effect of stronger magnetic fields produced by cryogenic magnets.

  4. Protein-based composite materials

    Directory of Open Access Journals (Sweden)

    Xiao Hu

    2012-05-01

    Full Text Available Protein-based composite biomaterials have been actively pursued as they can encompass a range of physical properties to accommodate a broader spectrum of functional requirements, such as elasticity to support diverse tissues. By optimizing molecular interfaces between structural proteins, useful composite materials can be fabricated as films, gels, particles, and fibers, as well as for electrical and optical devices. Such systems provide analogies to more traditional synthetic polymers yet with expanded utility due to the material's tunability, mechanical properties, degradability, biocompatibility, and functionalization, such as for drug delivery, biosensors, and tissue regeneration.

  5. Investigation of Coating Capability of Composite Materials

    Directory of Open Access Journals (Sweden)

    Yelda Akçin

    2013-07-01

    Full Text Available Nowadays, composite materials are widely used in the sectors that are overrated high strength / density and high elasticity modulus / density ratios such as defense industry, marine transportation, automotive and aerospace industry. However, because of the surface properties such as tribological behavior and low wear resistance their application areas are limited. Coating is the prominent process in order to improve these properties of the materials. In this study, hard ceramic powders (Al2O3 + TiO2 and CrO3 are coated to surface of glass fiber and carbon fiber reinforced epoxy matrix composite materials with plasma spray coating method started to be widely used todays and physical, mechanical and metallographic properties of obtained coatings were examined.

  6. Methods and compositions using calcium carbonate

    Energy Technology Data Exchange (ETDEWEB)

    Constantz, Brent R [Portola Valley, CA; Farsad, Kasra [San Jose, CA; Camire, Chris [San Jose, CA; Patterson, Joshua [Freedom, CA; Ginder-Vogel, Matthew [Los Gatos, CA; Yaccato, Karin [San Jose, CA; Stagnaro, John [Santa Clara, CA; Devenney, Martin [Mountain View, CA; Ries, Justin [Chapel Hill, NC

    2012-03-20

    Provided herein are compositions and methods including hydraulic cement, supplementary cementitious material, and/or self-cementing material. Methods for making the compositions and using the compositions are provided.

  7. Methods and compositions using calcium carbonate

    Energy Technology Data Exchange (ETDEWEB)

    Constantz, Brent R. (Portola Valley, CA); Farsad, Kasra (San Jose, CA); Camire, Chris (San Jose, CA); Chen, Irvin (San Jose, CA)

    2011-04-12

    Provided herein are compositions and methods including hydraulic cement, supplementary cementitious material, and/or self-cementing material. Methods for making the compositions and using the compositions are provided.

  8. Methods and compositions using calcium carbonate

    Energy Technology Data Exchange (ETDEWEB)

    Constantz, Brent R [Portola Valley, CA; Farsad, Kasra [San Jose, CA; Camire, Chris [San Jose, CA; Patterson, Joshua [Freedom, CA; Fernandez, Miguel [San Jose, CA; Yaccato, Karin [San Jose, CA; Thatcher, Ryan [Sunnyvale, CA; Stagnaro, John [Santa Clara, CA; Chen, Irvin [Santa Clara, CA; Omelon, Sidney [Willowdale, CA; Hodson, Keith [Palo Alto, CA; Clodic, Laurence [Sunnyvale, CA; Geramita, Katharine [Seattle, CA; Holland, Terence C [Auburn Township, OH; Ries, Justin [Chapel Hill, NC

    2012-02-14

    Provided herein are compositions and methods including hydraulic cement, supplementary cementitious material, and/or self-cementing material. Methods for making the compositions and using the compositions are provided.

  9. Methods and compositions using calcium carbonate

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Irvin; Fernandez, Miguel; Patterson, Joshua; Devenney, Martin

    2015-06-16

    Provided herein are compositions and methods including hydraulic cement, supplementary cementitious material, and/or self-cementing material. Methods for making the compositions and using the compositions are provided.

  10. Methods and compositions using calcium carbonate

    Science.gov (United States)

    Constantz, Brent R [Portola Valley, CA; Farsad, Kasra [San Jose, CA; Camire, Chris [San Jose, CA; Chen, Irvin [Santa Clara, CA; Ginder-Vogel, Matthew [Los Gatos, CA; Fernandez, Miguel [San Jose, CA

    2012-05-15

    Provided herein are compositions and methods including hydraulic cement, supplementary cementitious material, and/or self-cementing material. Methods for making the compositions and using the compositions are provided.

  11. Methods and compositions using calcium carbonate

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Irvin; Fernandez, Miguel; Patterson, Joshua; Devenney, Martin

    2015-01-13

    Provided herein are compositions and methods including hydraulic cement, supplementary cementitious material, and/or self-cementing material. Methods for making the compositions and using the compositions are provided.

  12. Methods and compositions using calcium carbonate

    Energy Technology Data Exchange (ETDEWEB)

    Constantz, Brent R. (Portola Valley, CA); Farsad, Kasra (San Jose, CA); Camire, Chris (San Jose, CA); Patterson, Joshua (Freedom, CA); Ginder-Vogel, Matthew (Los Gatos, CA); Yaccato, Karin (San Jose, CA); Stagnaro, John (Santa Clara, CA); Devenney, Martin (Mountain View, CA); Ries, Justin (Chapel Hill, NC)

    2011-11-22

    Provided herein are compositions and methods including hydraulic cement, supplementary cementitious material, and/or self-cementing material. Methods for making the compositions and using the compositions are provided.

  13. Creep of fibrous composite materials

    DEFF Research Database (Denmark)

    Lilholt, Hans

    1985-01-01

    Models are presented for the creep behaviour of fibrous composite materials with aligned fibres. The models comprise both cases where the fibres remain rigid in a creeping matrix and cases where the fibres are creeping in a creeping matrix. The treatment allows for several contributions to the cr......Models are presented for the creep behaviour of fibrous composite materials with aligned fibres. The models comprise both cases where the fibres remain rigid in a creeping matrix and cases where the fibres are creeping in a creeping matrix. The treatment allows for several contributions...... such as Ni + W-fibres, high temperature materials such as Ni + Ni3Al + Cr3C2-fibres, and medium temperature materials such as Al + SiC-fibres. For the first two systems reasonable consistency is found for the models and the experiments, while for the third system too many unquantified parameters exist...

  14. Investigation of woven composites as potential cryogenic tank materials

    Science.gov (United States)

    Islam, Md. S.; Melendez-Soto, E.; Castellanos, A. G.; Prabhakar, P.

    2015-12-01

    In this paper, carbon fiber and Kevlar® fiber woven composites were investigated as potential cryogenic tank materials for storing liquid fuel in spacecraft or rocket. Towards that end, both carbon and Kevlar® fiber composites were manufactured and tested with and without cryogenic exposure. The focus was on the investigation of the influence of initial cryogenic exposure on the degradation of the composite. Tensile, flexural and inter laminar shear strength (ILSS) tests were conducted, which indicate that Kevlar® and carbon textile composites are potential candidates for use under cryogenic exposure.

  15. Processing and Characterization of Carbon Nanotube Composites

    Science.gov (United States)

    Can, Roberto J.; Grimsley, Brian W.; Czabaj, Michael W.; Siochi, Emilie J.; Hull, Brandon

    2014-01-01

    Recent advances in the synthesis of large-scale quantities of carbon nanotubes (CNT) have provided the opportunity to study the mechanical properties of polymer matrix composites using these novel materials as reinforcement. Nanocomp Technologies, Inc. currently supplies large sheets with dimensions up to 122 cm x 244 cm containing both single-wall and few-wall CNTs. The tubes are approximately 1 mm in length with diameters ranging from 8 to 12 nm. In the present study being conducted at NASA Langley Research Center (LaRC), single and multiple layers of CNT sheets were infused or coated with various polymer solutions that included commercial toughened-epoxies and bismaleimides, as well as a LaRC developed polyimide. The resulting CNT composites were tested in tension using a modified version of ASTM D882-12 to determine their strength and modulus values. The effects of solvent treatment and mechanical elongation/alignment of the CNT sheets on the tensile performance of the composite were determined. Thin composites (around 50 wt% CNT) fabricated from acetone condensed and elongated CNT sheets with either a BMI or polyimide resin solution exhibited specific tensile moduli approaching that of toughened epoxy/ IM7 carbon fiber unidirectional composites.

  16. Carbon material for hydrogen storage

    Energy Technology Data Exchange (ETDEWEB)

    Bourlinos, Athanasios; Steriotis, Theodore; Stubos, Athanasios; Miller, Michael A

    2016-09-13

    The present invention relates to carbon based materials that are employed for hydrogen storage applications. The material may be described as the pyrolysis product of a molecular precursor such as a cyclic quinone compound. The pyrolysis product may then be combined with selected transition metal atoms which may be in nanoparticulate form, where the metals may be dispersed on the material surface. Such product may then provide for the reversible storage of hydrogen. The metallic nanoparticles may also be combined with a second metal as an alloy to further improve hydrogen storage performance.

  17. 碳纤维复合材料的创新方向%The Innovation directions of carbon ifber composite materials

    Institute of Scientific and Technical Information of China (English)

    罗益锋; 罗晰旻

    2016-01-01

    美国橡树岭国家实验室制造系统研究集团所从事的碳纤维复合材料(CFRP)研发工作,在一定程度上代表了当今世界CFRP成型技术和设备的创新方向,即朝着制造过程更快捷、效率更高和成本更低的方向发展,包括研发新型附加设备、自动化生产线、高精度设备或新模塑方法,其中3D印刷的CFRP成型技术已接近于实用化。%The research works of carbon fiber composite materials developed by the Manufacturing Systems Re-search Group at Oak Ridge National Laboratory represent theinnovation directions of CFRP forming technolo-gies and equipment today in the world to same extent, which are developing toward to make CFRP manufactur-ing faster, more efficient and cost-effective. Whether they are working on additive manufacturing, automated production, more precise machining or new methods of molding, in which 3-D printed CFRP technology is close to reality.

  18. Development of a novel composite material with carbon nanotubes assisted by self-assembled peptides designed in conjunction with β-sheet formation.

    Science.gov (United States)

    Hashida, Yasuhiko; Umeyama, Tomokazu; Mihara, Junya; Imahori, Hiroshi; Tsujimoto, Masahiko; Isoda, Seiji; Takano, Mikio; Hashida, Mitsuru

    2012-09-01

    A novel composite material is developed with single-walled carbon nanotubes (SWCNTs) and artificially designed peptides, and its chemical and physicochemical characteristics are evaluated with an aim toward biomedical application. The peptides were designed to form a β-sheet structure that would be suitable for wrapping SWCNTs. The complex of SWCNTs and peptide (SWCNT-peptide) showed good dispersibility in aqueous media and was considerably stable even in the absence of an excess amount of peptide in the media. The formation of SWCNT-peptide was confirmed by its performance in water, atomic force microscopy and transmission electron microscopy observation, and molecular modeling. The possibility of introducing various functions to SWCNT-peptide was also demonstrated by several methods, such as introduction of special amino acids, chemical modification, and additional complex formation based on electrostatic interaction. These results suggest the potential of the SWCNT-peptide complex as a molecular platform on which a desirable structure and/or function can be constructed for biomedical and industrial application.

  19. Hybrid Carbon-Carbon Ablative Composites for Thermal Protection in Aerospace

    Directory of Open Access Journals (Sweden)

    P. Sanoj

    2014-01-01

    Full Text Available Composite materials have been steadily substituting metals and alloys due to their better thermomechanical properties. The successful application of composite materials for high temperature zones in aerospace applications has resulted in extensive exploration of cost effective ablative materials. High temperature heat shielding to body, be it external or internal, has become essential in the space vehicles. The heat shielding primarily protects the substrate material from external kinetic heating and the internal insulation protects the subsystems and helps to keep coefficient of thermal expansion low. The external temperature due to kinetic heating may increase to about maximum of 500°C for hypersonic reentry space vehicles while the combustion chamber temperatures in case of rocket and missile engines range between 2000°C and 3000°C. Composite materials of which carbon-carbon composites or the carbon allotropes are the most preferred material for heat shielding applications due to their exceptional chemical and thermal resistance.

  20. Obtaining New Dental Materials Reinforced with Carbon Nanotubes

    Directory of Open Access Journals (Sweden)

    I.V. Zaporotskova

    2014-07-01

    Full Text Available The article seeks to explore the change of strength properties of composite polymer material on the basis of fast-hardening dental plastic "Carbogen", when reinforcing its coal-native nanotubes. Were discussed peculiarities of composition of Carboante, ways of creation of polymeric composition deposits by doping their carbon nanotubes, the results of measuring the strength characteristic characteristics obtained new polymer materials. On the basis of the analysis of the practical and the theoretical-sky research, conclusions were drawn on the feasibility of a new filling material with the use of carbon nanotubes with unique strength characteristics and use of their in dentistry.

  1. Fiber-reinforced composites materials, manufacturing, and design

    CERN Document Server

    Mallick, P K

    2007-01-01

    The newly expanded and revised edition of Fiber-Reinforced Composites: Materials, Manufacturing, and Design presents the most up-to-date resource available on state-of-the-art composite materials. This book is unique in that it not only offers a current analysis of mechanics and properties, but also examines the latest advances in test methods, applications, manufacturing processes, and design aspects involving composites. This third edition presents thorough coverage of newly developed materials including nanocomposites. It also adds more emphasis on underlying theories, practical methods, and problem-solving skills employed in real-world applications of composite materials. Each chapter contains new examples drawn from diverse applications and additional problems to reinforce the practical relevance of key concepts. New in The Third Edition: Contains new sections on material substitution, cost analysis, nano- and natural fibers, fiber architecture, and carbon-carbon composites Provides a new chapter on poly...

  2. Fermentation based carbon nanotube multifunctional bionic composites

    Science.gov (United States)

    Valentini, Luca; Bon, Silvia Bittolo; Signetti, Stefano; Tripathi, Manoj; Iacob, Erica; Pugno, Nicola M.

    2016-06-01

    The exploitation of the processes used by microorganisms to digest nutrients for their growth can be a viable method for the formation of a wide range of so called biogenic materials that have unique properties that are not produced by abiotic processes. Here we produced living hybrid materials by giving to unicellular organisms the nutrient to grow. Based on bread fermentation, a bionic composite made of carbon nanotubes (CNTs) and a single-cell fungi, the Saccharomyces cerevisiae yeast extract, was prepared by fermentation of such microorganisms at room temperature. Scanning electron microscopy analysis suggests that the CNTs were internalized by the cell after fermentation bridging the cells. Tensile tests on dried composite films have been rationalized in terms of a CNT cell bridging mechanism where the strongly enhanced strength of the composite is governed by the adhesion energy between the bridging carbon nanotubes and the matrix. The addition of CNTs also significantly improved the electrical conductivity along with a higher photoconductive activity. The proposed process could lead to the development of more complex and interactive structures programmed to self-assemble into specific patterns, such as those on strain or light sensors that could sense damage or convert light stimulus in an electrical signal.

  3. Lignin-Derived Advanced Carbon Materials.

    Science.gov (United States)

    Chatterjee, Sabornie; Saito, Tomonori

    2015-12-07

    Lignin is a highly abundant source of renewable carbon that can be considered as a valuable sustainable source of biobased materials. By applying specific pretreatments and manufacturing methods, lignin can be converted into a variety of value-added carbon materials. However, the physical and chemical heterogeneities of lignin complicate its use as a feedstock. Herein lignin manufacturing process, the effects of pretreatments and manufacturing methods on the properties of product lignin, and structure-property relationships in various applications of lignin-derived carbon materials, such as carbon fibers, carbon mats, activated carbons, carbon films, and templated carbon, are discussed.

  4. [Carbon fiber-reinforced plastics as implant materials].

    Science.gov (United States)

    Bader, R; Steinhauser, E; Rechl, H; Siebels, W; Mittelmeier, W; Gradinger, R

    2003-01-01

    Carbon fiber-reinforced plastics have been used clinically as an implant material for different applications for over 20 years.A review of technical basics of the composite materials (carbon fibers and matrix systems), fields of application,advantages (e.g., postoperative visualization without distortion in computed and magnetic resonance tomography), and disadvantages with use as an implant material is given. The question of the biocompatibility of carbon fiber-reinforced plastics is discussed on the basis of experimental and clinical studies. Selected implant systems made of carbon composite materials for treatments in orthopedic surgery such as joint replacement, tumor surgery, and spinal operations are presented and assessed. Present applications for carbon fiber reinforced plastics are seen in the field of spinal surgery, both as cages for interbody fusion and vertebral body replacement.

  5. Sustainable carbon materials from hydrothermal processes

    CERN Document Server

    Titirici, Maria-Magdalena

    2013-01-01

    The production of low cost and environmentally friendly high performing carbon materials is crucial for a sustainable future. Sustainable Carbon Materials from Hydrothermal Processes describes a sustainable and alternative technique to produce carbon from biomass in water at low temperatures, a process known as Hydrothermal Carbonization (HTC). Sustainable Carbon Materials from Hydrothermal Processes presents an overview of this new and rapidly developing field, discussing various synthetic approaches, characterization of the final products, and modern fields of application fo

  6. Multi-length Scale Material Model Development for Armorgrade Composites

    Science.gov (United States)

    2014-05-02

    synthesis -/processing-induced defects; (c) effect of 3 synthesis -/processing-induced defects on PPTA-fiber properties; (d) effect of fiber-/ yarn ...Derivation of the Materials Constitutive Relations for Carbon Nanotube Reinforced Poly-Vinyl-Ester-Epoxy Based Composites,” Journal of Materials Science, 42...fabric or PPTA-fiber-reinforced polymer-matrix composites. Specifically, the role of various material- synthesis -/fiber-processing-induced defects, as

  7. Enhanced graphitization of carbon around carbon nanotubes during the formation of carbon nanotube/graphite composites by pyrolysis of carbon nanotube/polyaniline composites.

    Science.gov (United States)

    Nam, Dong Hoon; Cha, Seung Il; Jeong, Yong Jin; Hong, Soon Hyung

    2013-11-01

    The carbon nanotubes (CNTs) are actively applied to the reinforcements for composite materials during last decade. One of the attempts is development of CNT/Carbon composites. Although there are some reports on the enhancement of mechanical properties by addition of CNTs in carbon or carbon fiber, it is far below the expectation. Considering the microstructure of carbon materials such as carbon fiber, the properties of them can be modified and enhanced by control of graphitization and alignment of graphene planes. In this study, enhanced graphitization of carbon has been observed the vicinity of CNTs during the pyrolysis of CNT/Polyaniline composites. As a result, novel types of composite, consisting of treading CNTs and coated graphite, can be fabricated. High-resolution transmission electron microscopy revealed a specific orientation relationship between the graphene layers and the CNTs, with an angle of 110 degrees between the layers and the CNT axis. The possibility of graphene alignment control in the carbon by the addition of CNTs is demonstrated.

  8. Carbon Nanomaterials as Reinforcements for Composites

    Science.gov (United States)

    Zhu, Shen; Su, Ching-Hua; Lehoczky, S. L.; Curreri, Peter A. (Technical Monitor)

    2002-01-01

    Carbon nanomaterials including fellerenes, nanotubes (CNT) and nanofibers have been proposed for many applications. One of applications is to use the carbon nanomaterials as reinforcements for composites, especially for polymer matrices. Carbon nanotubes is a good reinforcement for lightweight composite applications due to its low mass density and high Young's modulus. Two obscures need to overcome for carbon nanotubes as reinforcements in composites, which are large quantity production and functioning the nanotubes. This presentation will discuss the carbon nanotube growth by chemical vapor deposition. In order to reduce the cost of producing carbon nanotubes as well as preventing the sliding problems, carbon nanotubes were also synthesized on carbon fibers. The synthesis process and characterization results of nanotubes and nanotubes/fibers will be discussed in the presentation.

  9. Friction and wear behavior of carbon fiber reinforced brake materials

    Institute of Scientific and Technical Information of China (English)

    Du-qing CHENG; Xue-tao WANG; Jian ZHU; Dong-bua QIU; Xiu-wei CHENG; Qing-feng GUAN

    2009-01-01

    A new composite brake material was fabri-cated with metallic powders, barium sulphate and modified phenolic resin as the matrix and carbon fiber as the reinforced material. The friction, wear and fade character-istics of this composite were determined using a D-MS friction material testing machine. The surface structure of carbon fiber reinforced friction materials was analyzed by scanning electronic microscopy (SEM). Glass fiber-reinforced and asbestos fiber-reinforced composites with the same matrix were also fabricated for comparison. The carbon fiber-reinforced friction materials (CFRFM) shows lower wear rate than those of glass fiber- and asbestos fiber-reinforced composites in the temperature range of 100℃-300℃. It is interesting that the frictional coefficient of the carbon fiber-reinforced friction materials increases as frictional temperature increases from 100℃ to 300℃, while the frictional coefficients of the other two composites decrease during the increasing temperatures. Based on the SEM observation, the wear mechanism of CFRFM at low temperatures included fiber thinning and pull-out. At high temperature, the phenolic matrix was degraded and more pull-out enhanced fiber was demonstrated. The properties of carbon fiber may be the main reason that the CFRFM possess excellent tribological performances.

  10. Multi-material Preforming of Structural Composites

    Energy Technology Data Exchange (ETDEWEB)

    Norris, Robert E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Eberle, Cliff C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pastore, Christopher M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sudbury, Thomas Z. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Xiong, Fue [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hartman, David [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-05-01

    Fiber-reinforced composites offer significant weight reduction potential, with glass fiber composites already widely adopted. Carbon fiber composites deliver the greatest performance benefits, but their high cost has inhibited widespread adoption. This project demonstrates that hybrid carbon-glass solutions can realize most of the benefits of carbon fiber composites at much lower cost. ORNL and Owens Corning Reinforcements along with program participants at the ORISE collaborated to demonstrate methods for produce hybrid composites along with techniques to predict performance and economic tradeoffs. These predictions were then verified in testing coupons and more complex demonstration articles.

  11. Functionalized Carbon Nanotube-Polymer Composites and Interactions with Radiation

    Science.gov (United States)

    Barrera, Enrique V. (Inventor); Wilkins, Richard (Inventor); Shofner, Meisha (Inventor); Pulikkathara, Merlyn X. (Inventor); Vaidyanathan, Ranjii (Inventor)

    2014-01-01

    The present invention involves the interaction of radiation with functionalized carbon nanotubes that have been incorporated into various host materials, particularly polymeric ones. The present invention is directed to chemistries, methods, and apparatuses which exploit this type of radiation interaction, and to the materials which result from such interactions. The present invention is also directed toward the time dependent behavior of functionalized carbon nanotubes in such composite systems.

  12. Hybrid Composite of Polyaniline Containing Carbon Nanotube

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Carbon nanotube-polyaniline hybrid material was synthesized by emulsion polymerization in-situ. The morphology of hybrid material was studied by TEM and X-ray diffraction. The conductivity of nanocomposite increases with the increasing of carbon nanotube content because of the new conductivity passageways formed by carbon nanotubes.

  13. A Review of Biomedical Composite Materials

    Institute of Scientific and Technical Information of China (English)

    吴珊珊

    2013-01-01

    This article addresses the review of the biomedical composite materials.It introduces the operational definition,the classification of biomedical composite materials,and its constituents within itself.In this thesis,the last part presents the application of this kind of material.By writing this paper,I hope that people will get a comprehensive knowledge of the biomedical composite material and make further and deeper research in this material by which way to animate the material science industry.

  14. Emissivity Results on High Temperature Coatings for Refractory Composite Materials

    Science.gov (United States)

    Ohlhorst, Craig W.; Vaughn, Wallace L.; Daryabeigi, Kamran; Lewis, Ronald K.; Rodriguez, Alvaro C.; Milhoan, James D.; Koenig, John R.

    2007-01-01

    The directional emissivity of various refractory composite materials considered for application for reentry and hypersonic vehicles was investigated. The directional emissivity was measured at elevated temperatures of up to 3400 F using a directional spectral radiometric technique during arc-jet test runs. A laboratory-based relative total radiance method was also used to measure total normal emissivity of some of the refractory composite materials. The data from the two techniques are compared. The paper will also compare the historical database of Reinforced Carbon-Carbon emissivity measurements with emissivity values generated recently on the material using the two techniques described in the paper.

  15. Coating effects on thermal properties of carbon carbon and carbon silicon carbide composites for space thermal protection systems

    Science.gov (United States)

    Albano, M.; Morles, R. B.; Cioeta, F.; Marchetti, M.

    2014-06-01

    Many are the materials for hot structures, but the most promising one are the carbon based composites nowadays. This is because they have good characteristics with a high stability at high temperatures, preserving their mechanical properties. Unfortunately, carbon reacts rapidly with oxygen and the composites are subjected to oxidation degradation. From this point of view CC has to be modified in order to improve its thermal and oxidative resistance. The most common solutions are the use of silicon carbide into the carbon composites matrix (SiC composites) to make the thermal properties increase and the use of coating on the surface in order to protect the composite from the space plasma effects. Here is presented an experimental study on coating effects on these composites. Thermal properties of coated and non coated materials have been studied and the thermal impact on the matrix and surface degradation is analyzed by a SEM analysis.

  16. Carbon Nanotubes Reinforced Composites for Biomedical Applications

    OpenAIRE

    Wei Wang; Yuhe Zhu; Susan Liao; Jiajia Li

    2014-01-01

    This review paper reported carbon nanotubes reinforced composites for biomedical applications. Several studies have found enhancement in the mechanical properties of CNTs-based reinforced composites by the addition of CNTs. CNTs reinforced composites have been intensively investigated for many aspects of life, especially being made for biomedical applications. The review introduced fabrication of CNTs reinforced composites (CNTs reinforced metal matrix composites, CNTs reinforced polymer matr...

  17. Using Composite Materials in a Cryogenic Pump

    Science.gov (United States)

    Batton, William D.; Dillard, James E.; Rottmund, Matthew E.; Tupper, Michael L.; Mallick, Kaushik; Francis, William H.

    2008-01-01

    Several modifications have been made to the design and operation of an extended-shaft cryogenic pump to increase the efficiency of pumping. In general, the efficiency of pumping a cryogenic fluid is limited by thermal losses which is itself caused by pump inefficiency and leakage of heat through the pump structure. A typical cryogenic pump includes a drive shaft and two main concentric static components (an outer pressure containment tube and an intermediate static support tube) made from stainless steel. The modifications made include replacement of the stainless-steel drive shaft and the concentric static stainless-steel components with components made of a glass/epoxy composite. The leakage of heat is thus reduced because the thermal conductivity of the composite is an order of magnitude below that of stainless steel. Taking advantage of the margin afforded by the decrease in thermal conductivity, the drive shaft could be shortened to increase its effective stiffness, thereby increasing the rotordynamic critical speeds, thereby further making it possible to operate the pump at a higher speed to increase pumping efficiency. During the modification effort, an analysis revealed that substitution of the shorter glass/epoxy shaft for the longer stainless-steel shaft was not, by itself, sufficient to satisfy the rotordynamic requirements at the desired increased speed. Hence, it became necessary to increase the stiffness of the composite shaft. This stiffening was accomplished by means of a carbon-fiber-composite overwrap along most of the length of the shaft. Concomitantly with the modifications described thus far, it was necessary to provide for joining the composite-material components with metallic components required by different aspects of the pump design. An adhesive material formulated specially to bond the composite and metal components was chosen as a means to satisfy these requirements.

  18. High Volume Fraction Carbon Nanotube Composites for Aerospace Applications

    Science.gov (United States)

    Siochi, E. J.; Kim, J.-W.; Sauti, G.; Cano, R. J.; Wincheski, R. A.; Ratcliffe, J. G.; Czabaj, M.

    2016-01-01

    Reported mechanical properties of carbon nanotubes (CNTs) at the nanoscale suggest their potential to enable significantly lighter structures of interest for space applications. However, their utility depends on the retention of these properties in bulk material formats that permit practical fabrication of large structures. This presentation summarizes recent progress made to produce carbon nanotube composites with specific tensile properties that begin to rival those of carbon fiber reinforced polymer composites. CNT content in these nanocomposites was greater than 70% by weight. Tested nanocomposite specimens were fabricated from kilometers or tens of square meters of CNT, depending on the starting material format. Processing methods to yield these results, and characterization and testing to evaluate the performance of these composites will be discussed. The final objective is the demonstration of a CNT composite overwrapped pressure vessel to be flight tested in the Fall of 2016.

  19. Synthesis and characterization of carbon cryogel/zeolite composites

    Directory of Open Access Journals (Sweden)

    Biljana Babić

    2011-06-01

    Full Text Available A novel method for synthesis of carbon cryogel/zeolite composites was obtained. Method considers forming of carbon cryogel from the sol-gel polycondenzation of resorcinol and formaldehyde, followed by freeze drying, and subsequent pyrolysis in presence of different amount of zeolite. Characterization of composite materials by nitrogen adsorption shows that samples are micro- and mesoporous and that specific surface area decrease with increasing the amount of zeolite in samples. XRD method confirms amorphous structure of carbon cryogel and crystalline structure of zeolite, i.e. structure of zeolite has not been destroyed by carbonization process. SEM and EDX analyses reveal homogenous distribution of zeolite through out carbon cryogel and corresponding composition.

  20. Template-free fabrication and morphology regulation of Ag@carbon composite structure

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Wenyan, E-mail: zhangwenyan8531@gmail.com [College of Material Engineering, Jinling Institute of Technology, Nanjing (China); Hao, Lingyun; Lin, Qin [College of Material Engineering, Jinling Institute of Technology, Nanjing (China); Lu, Chunhua; Xu, Zhongzi [College of Materials Science and Engineering, Nanjing Technology University, Nanjing (China); Chen, Xiaoyu [College of Material Engineering, Jinling Institute of Technology, Nanjing (China)

    2014-12-15

    Graphical abstract: - Highlights: • A simple and low-cost method to prepare Ag@C composite material. • AgNO{sub 3} plays an important role in tuning size and functional groups of products. • HTC reaction time is also a key factor for regulating the Ag@C structure. - Abstract: Ag–carbon composite materials were prepared without any template by hydrothermal carbonization of solvable starch. The composite materials are composed of Ag cores and carbonaceous shell to form a core–shell (Ag@carbon) structure. During the hydrothermal carbonization process, the aromatization and carbonization of solvable starch endowed the Ag@carbon composite structure with abundant aromatic, hydroxyl and carbonyl groups. The AgNO{sub 3} concentration and HTC reaction time are two important factors for regulating the size, morphology and functional groups of the composite material. With the increasing of AgNO{sub 3} concentration, morphologies of the composite material turned from spheres to wires.

  1. Composite materials for fusion applications

    Energy Technology Data Exchange (ETDEWEB)

    Jones, R.H.; Henager, C.H. Jr.; Hollenberg, G.W.

    1991-10-01

    Ceramic matrix composites, CMCs, are being considered for advanced first-wall and blanket structural applications because of their high-temperature properties, low neutron activation, low density and low coefficient of expansion coupled with good thermal conductivity and corrosion behavior. This paper presents a review and analysis of the hermetic, thermal conductivity, corrosion, crack growth and radiation damage properties of CMCs. It was concluded that the leak rates of a gaseous coolant into the plasma chamber or tritium out of the blanket could exceed design criteria if matrix microcracking causes existing porosity to become interconnected. Thermal conductivities of unirradiated SiC/SiC and C/SiC materials are about 1/2 to 2/3 that of Type 316 SS whereas the thermal conductivity for C/C composites is seven times larger. The thermal stress figure-of-merit value for CMCs exceeds that of Type 316 SS for a single thermal cycle. SiC/SiC composites are very resistant to corrosion and are expected to be compatible with He or Li coolants if the O{sub 2} concentrations are maintained at the appropriate levels. CMCs exhibit subcritical crack growth at elevated temperatures and the crack velocity is a function of the corrosion conditions. The radiation stability of CMCs will depend on the stability of the fiber, microcracking of the matrix, and the effects of gaseous transmutation products on properties. 23 refs., 14 figs., 1 tab.

  2. Computational Nanomechanics of Carbon Nanotubes and Composites

    Science.gov (United States)

    Srivastava, Deepak; Wei, Chenyu; Cho, Kyeongjae; Biegel, Bryan (Technical Monitor)

    2002-01-01

    Nanomechanics of individual carbon and boron-nitride nanotubes and their application as reinforcing fibers in polymer composites has been reviewed with interplay of theoretical modeling, computer simulations and experimental observations. The emphasis in this work is on elucidating the multi-length scales of the problems involved, and of different simulation techniques that are needed to address specific characteristics of individual nanotubes and nanotube polymer-matrix interfaces. Classical molecular dynamics simulations are shown to be sufficient to describe the generic behavior such as strength and stiffness modulus but are inadequate to describe elastic limit and nature of plastic buckling at large strength. Quantum molecular dynamics simulations are shown to bring out explicit atomic nature dependent behavior of these nanoscale materials objects that are not accessible either via continuum mechanics based descriptions or through classical molecular dynamics based simulations. As examples, we discus local plastic collapse of carbon nanotubes under axial compression and anisotropic plastic buckling of boron-nitride nanotubes. Dependence of the yield strain on the strain rate is addressed through temperature dependent simulations, a transition-state-theory based model of the strain as a function of strain rate and simulation temperature is presented, and in all cases extensive comparisons are made with experimental observations. Mechanical properties of nanotube-polymer composite materials are simulated with diverse nanotube-polymer interface structures (with van der Waals interaction). The atomistic mechanisms of the interface toughening for optimal load transfer through recycling, high-thermal expansion and diffusion coefficient composite formation above glass transition temperature, and enhancement of Young's modulus on addition of nanotubes to polymer are discussed and compared with experimental observations.

  3. Microstructure of C/C Composites with Different Matrix Carbon

    Directory of Open Access Journals (Sweden)

    LIU Hao

    2016-07-01

    Full Text Available The microstructure of carbon/carbon(C/C composites with different matrix carbon was studied by polarized light microscopy (PLM, scanning electron microscopy (SEM, transmission electron microscopy (TEM and XRD techniques respectively. PLM results indicate that the different matrix carbon exhibits different optical reactivity, and the average optical reactivity is gradually enhanced from normal pitch carbon, smooth laminar of pyrocarbon, rough laminar of pyrocarbon to mesophase pitch carbon; SEM results show that the normal pitch carbon is mainly of grapy structure, the pyrocarbon exhibits like-crinkle lamellar structure, while the mesophase pitch carbon exhibits lamellar banded structure with different shapes. Under HRTEM, the lattice fringes of the mesophase pitch carbon are arranged regularly, is a long range ordered crystal structure, and the preferred orientation is high. The degree of the graphite and the interlayer spacing of the material B (mesophase pitch-based C/C composites are better than that of the material D (pyrocarbon-based C/C composites.

  4. Carbon nanotube-polymer composites manufacture, properties, and applications

    CERN Document Server

    Grady, Brian P

    2011-01-01

    The accessible compendium of polymers in carbon nanotubes (CNTs) Carbon nanotubes (CNTs)-extremely thin tubes only a few nanometers in diameter but able to attain lengths thousands of times greater-are prime candidates for use in the development of polymer composite materials. Bringing together thousands of disparate research works, Carbon Nanotube-Polymer Composites: Manufacture, Properties, and Applications covers CNT-polymers from synthesis to potential applications, presenting the basic science and engineering of this dynamic and complex area in an accessible, readable way. Desi

  5. Carbon nanotube-polymer composite actuators

    Science.gov (United States)

    Gennett, Thomas; Raffaelle, Ryne P.; Landi, Brian J.; Heben, Michael J.

    2008-04-22

    The present invention discloses a carbon nanotube (SWNT)-polymer composite actuator and method to make such actuator. A series of uniform composites was prepared by dispersing purified single wall nanotubes with varying weight percents into a polymer matrix, followed by solution casting. The resulting nanotube-polymer composite was then successfully used to form a nanotube polymer actuator.

  6. A Novel Nanofilm Sensor Based on Poly-(Alizarin Red)/Fe3O4 Magnetic Nanoparticles-Multiwalled Carbon Nanotubes Composite Material for Determination of Nitrite.

    Science.gov (United States)

    Qu, Jianying; Dong, Ying; Yong, Wang; Lou, Tongfang; Du, Xueping; Qu, Jianhang

    2016-03-01

    Fe3O4 magnetic nanoparticles were synthesized by chemical co-precipitation with sodium citrate as surfactant and were characterized by FT-IR spectrometer, X-ray diffraction and transmission electron microscopy. A novel nitrite sensor was fabricated by electropolymerization of alizarin red on the surface of glassy carbon electrode modified with Fe3O4-multiwalled carbon nanotubes composite nanofilm. Under the optimal experimental conditions, it was showed that the proposed sensor exhibited good electrocatalytic activity to the oxidation of nitrite, and the peak current increased linearly with the nitrite concentration from 9.64 x 10(-6) mol x L(-1) to 1.30 x 10(-3) mol x L(-1) (R = 0.9976) with a detection limit of 1.19 x 10(-6) mol x L(-1) (S/N = 3). This sensor showed excellent sensitivity, wide linear range, stability and repeatability for nitrite determination with potential applications.

  7. Carbon nanotubes reinforced composites for biomedical applications.

    Science.gov (United States)

    Wang, Wei; Zhu, Yuhe; Liao, Susan; Li, Jiajia

    2014-01-01

    This review paper reported carbon nanotubes reinforced composites for biomedical applications. Several studies have found enhancement in the mechanical properties of CNTs-based reinforced composites by the addition of CNTs. CNTs reinforced composites have been intensively investigated for many aspects of life, especially being made for biomedical applications. The review introduced fabrication of CNTs reinforced composites (CNTs reinforced metal matrix composites, CNTs reinforced polymer matrix composites, and CNTs reinforced ceramic matrix composites), their mechanical properties, cell experiments in vitro, and biocompatibility tests in vivo.

  8. Carbon Nanotubes Reinforced Composites for Biomedical Applications

    Directory of Open Access Journals (Sweden)

    Wei Wang

    2014-01-01

    Full Text Available This review paper reported carbon nanotubes reinforced composites for biomedical applications. Several studies have found enhancement in the mechanical properties of CNTs-based reinforced composites by the addition of CNTs. CNTs reinforced composites have been intensively investigated for many aspects of life, especially being made for biomedical applications. The review introduced fabrication of CNTs reinforced composites (CNTs reinforced metal matrix composites, CNTs reinforced polymer matrix composites, and CNTs reinforced ceramic matrix composites, their mechanical properties, cell experiments in vitro, and biocompatibility tests in vivo.

  9. Carbon fiber composite molecular sieves

    Energy Technology Data Exchange (ETDEWEB)

    Burchell, T.D.; Rogers, M.R.; Williams, A.M.

    1996-06-01

    The removal of CO{sub 2} is of significance in several energy applications. The combustion of fossil fuels, such as coal or natural gas, releases large volumes of CO{sub 2} to the environment. Several options exist to reduce CO{sub 2} emissions, including substitution of nuclear power for fossil fuels, increasing the efficiency of fossil plants and capturing the CO{sub 2} prior to emission to the environment. All of these techniques have the attractive feature of limiting the amount of CO{sub 2} emitted to the atmosphere, but each has economic, technical, or societal limitations. In the production of natural gas, the feed stream from the well frequently contains contaminants and diluents which must be removed before the gas can enter the pipeline distribution system. Notable amongst these diluent gasses is CO{sub 2}, which has no calorific value. Currently, the pipeline specification calls for <2 mol % CO{sub 2} in the gas. Gas separation is thus a relevant technology in the field of energy production. A novel separation system based on a parametric swing process has been developed that utilizes the unique combination of properties exhibited by our carbon fiber composite molecular sieve (CFCMS).

  10. Process Optimization of Bismaleimide (BMI) Resin Infused Carbon Fiber Composite

    Science.gov (United States)

    Ehrlich, Joshua W.; Tate, LaNetra C.; Cox, Sarah B.; Taylor, Brian J.; Wright, M. Clara; Faughnan, Patrick D.; Batterson, Lawrence M.; Caraccio, Anne J.; Sampson, Jeffery W.

    2013-01-01

    Engineers today are presented with the opportunity to design and build the next generation of space vehicles out of the lightest, strongest, and most durable materials available. Composites offer excellent structural characteristics and outstanding reliability in many forms that will be utilized in future aerospace applications including the Commercial Crew and Cargo Program and the Orion space capsule. NASA's Composites for Exploration (CoEx) project researches the various methods of manufacturing composite materials of different fiber characteristics while using proven infusion methods of different resin compositions. Development and testing on these different material combinations will provide engineers the opportunity to produce optimal material compounds for multidisciplinary applications. Through the CoEx project, engineers pursue the opportunity to research and develop repair patch procedures for damaged spacecraft. Working in conjunction with Raptor Resins Inc., NASA engineers are utilizing high flow liquid infusion molding practices to manufacture high-temperature composite parts comprised of intermediate modulus 7 (IM7) carbon fiber material. IM7 is a continuous, high-tensile strength composite with outstanding structural qualities such as high shear strength, tensile strength and modulus as well as excellent corrosion, creep, and fatigue resistance. IM7 carbon fiber, combined with existing thermoset and thermoplastic resin systems, can provide improvements in material strength reinforcement and deformation-resistant properties for high-temperature applications. Void analysis of the different layups of the IM7 material discovered the largest total void composition within the [ +45 , 90 , 90 , -45 ] composite panel. Tensile and compressional testing proved the highest mechanical strength was found in the [0 4] layup. This paper further investigates the infusion procedure of a low-cost/high-performance BMI resin into an IM7 carbon fiber material and the

  11. Appreciating the role of carbon nanotube composites in preventing biofouling and promoting biofilms on material surfaces in environmental engineering: a review.

    Science.gov (United States)

    Upadhyayula, Venkata K K; Gadhamshetty, Venkataramana

    2010-01-01

    The ability of carbon nanotubes (CNTs) to undergo surface modification allows them to form nanocomposites (NCs) with materials such as polymers, metal nanoparticles, biomolecules, and metal oxides. The biocidal nature, protein fouling resistance, and fouling release properties of CNT-NCs render them the perfect material for biofouling prevention. At the same time, the cytotoxicity of CNT-NCs can be reduced before applying them as substrates to promote biofilm formation in environmental biotechnology applications. This paper reviews the potential prospects of CNT-NCs to accomplish two widely varying objectives in environmental engineering applications: (i) preventing biofouling, and (ii) promoting the formation of desirable biofilms on materials surface. This paper addresses practical issues such as costs, risks to human health, and ecological impacts that are associated with the application, development and commercialization of CNT-NC technology.

  12. Activated Carbon Composites for Air Separation

    Energy Technology Data Exchange (ETDEWEB)

    Baker, Frederick S [ORNL; Contescu, Cristian I [ORNL; Tsouris, Costas [ORNL; Burchell, Timothy D [ORNL

    2011-09-01

    Coal-derived synthesis gas is a potential major source of hydrogen for fuel cells. Oxygen-blown coal gasification is an efficient approach to achieving the goal of producing hydrogen from coal, but a cost-effective means of enriching O2 concentration in air is required. A key objective of this project is to assess the utility of a system that exploits porous carbon materials and electrical swing adsorption to produce an O2-enriched air stream for coal gasification. As a complement to O2 and N2 adsorption measurements, CO2 was used as a more sensitive probe molecule for the characterization of molecular sieving effects. To further enhance the potential of activated carbon composite materials for air separation, work was implemented on incorporating a novel twist into the system; namely the addition of a magnetic field to influence O2 adsorption, which is accompanied by a transition between the paramagnetic and diamagnetic states. The preliminary findings in this respect are discussed.

  13. Fabrication of polytetrafluoroethylene/carbon fiber composites using radiation crosslinking

    Science.gov (United States)

    Oshima, Akihiro; Udagawa, Akira; Tanaka, Shigeru

    2001-07-01

    A fabrication method for fiber-reinforced plastic (FRP) composites based on carbon fibers and polytetrafluoroethylene (PTFE) which was crosslinked by electron beam (EB) irradiation under specific conditions was studied. Though the fabricated composite showed high mechanical properties compared with a ready-made PTFE composite (non-crosslinked PTFE with 5˜20 wt% filler), mechanical properties of laminated panels were a bit poor compared with those of usual FRP. It was found that the toughness of the PTFE matrix is poor in the composite. On the other hand, the one-ply sheet of carbon fibers and crosslinked PTFE composite showed good mechanical properties for sheet-shape materials. The wettability of the obtained crosslinked PTFE composite is hardly changed by crosslinking and reinforcement.

  14. Fabrication of polytetrafluoroethylene/carbon fiber composites using radiation crosslinking

    Energy Technology Data Exchange (ETDEWEB)

    Oshima, Akihiro E-mail: aks@taka.jaeri.go.jp; Udagawa, Akira; Tanaka, Shigeru

    2001-07-01

    A fabrication method for fiber-reinforced plastic (FRP) composites based on carbon fibers and polytetrafluoroethylene (PTFE) which was crosslinked by electron beam (EB) irradiation under specific conditions was studied. Though the fabricated composite showed high mechanical properties compared with a ready-made PTFE composite (non-crosslinked PTFE with 5{approx}20 wt% filler), mechanical properties of laminated panels were a bit poor compared with those of usual FRP. It was found that the toughness of the PTFE matrix is poor in the composite. On the other hand, the one-ply sheet of carbon fibers and crosslinked PTFE composite showed good mechanical properties for sheet-shape materials. The wettability of the obtained crosslinked PTFE composite is hardly changed by crosslinking and reinforcement.

  15. Bioactive carbon-PEEK composites prepared by chemical surface treatment.

    Science.gov (United States)

    Miyazaki, Toshiki; Matsunami, Chisato; Shirosaki, Yuki

    2017-01-01

    Polyetheretherketone (PEEK) has attracted much attention as an artificial intervertebral spacer for spinal reconstruction. Furthermore, PEEK plastic reinforced with carbon fiber has twice the bending strength of pure PEEK. However, the PEEK-based materials do not show ability for direct bone bonding, i.e., bioactivity. Although several trials have been conducted for enabling PEEK with bioactivity, few studies have reported on bioactive surface modification of carbon-PEEK composites. In the present study, we attempted the preparation of bioactive carbon-PEEK composites by chemical treatments with H2SO4 and CaCl2. Bioactivity was evaluated by in vitro apatite formation in simulated body fluid (SBF). The apatite formation on the carbon-PEEK composite was compared with that of pure PEEK. Both pure PEEK and carbon-PEEK composite formed the apatite in SBF when they were treated with H2SO4 and CaCl2; the latter showed higher apatite-forming ability than the former. It is conjectured that many functional groups able to induce the apatite nucleation, such as sulfo and carboxyl groups, are incorporated into the dispersed carbon phase in the carbon-PEEK composites.

  16. Improved fire retardancy of thermoset composites modified with carbon nanofibers

    Directory of Open Access Journals (Sweden)

    Zhongfu Zhao and Jan Gou

    2009-01-01

    Full Text Available Multifunctional thermoset composites were made from polyester resin, glass fiber mats and carbon nanofiber sheets (CNS. Their flaming behavior was investigated with cone calorimeter under well-controlled combustion conditions. The heat release rate was lowered by pre-planting carbon nanofiber sheets on the sample surface with the total fiber content of only 0.38 wt.%. Electron microscopy showed that carbon nanofiber sheet was partly burned and charred materials were formed on the combusting surface. Both the nanofibers and charred materials acted as an excellent insulator and/or mass transport barrier, improving the fire retardancy of the composite. This behavior agrees well with the general mechanism of fire retardancy in various nanoparticle-thermoplastic composites.

  17. Materials and electromagnetism. The modeling of composite materials; Materiaux en electromagnetisme. Modelisation des materiaux composites

    Energy Technology Data Exchange (ETDEWEB)

    Priou, A. [Institut Universitaire de Technologie, 92 - Ville-d' Avray (France)

    1999-01-01

    Maxwell laws are briefly described and the different types of electromagnetic materials are presented. Composite materials are made up of at least 2 phases: a host phase and an inclusion. The inclusion is a discontinuous phase coming from a conducting material (metal, carbon based material, semi-conductor, solid electrolytes or conducting polymers) and is spread within the host phase either in an aleatory or organized way. The modeling of such media can be made by 3 different approaches. In the multi-diffusion approach, the size of the particles enclosed in the host material and their mutual interactions are taken into account. The quasi-static approach allows the definition of an equivalent medium in order to describe percolation phenomena. The approach based on cluster theory gives a complete mathematical description of composite materials. The modeling of dielectric-conducting multilayer is also presented. The last part of the article is dedicated to the characteristics and applications of chiral media and of last generation electromagnetic materials. (A.C.)

  18. Engineered Molecular Chain Ordering in Single-Walled Carbon Nanotubes/Polyaniline Composite Films for High-Performance Organic Thermoelectric Materials.

    Science.gov (United States)

    Wang, Liming; Yao, Qin; Xiao, Juanxiu; Zeng, Kaiyang; Qu, Sanyin; Shi, Wei; Wang, Qun; Chen, Lidong

    2016-06-21

    Single-walled carbon nanotubes (SWNTs)/polyaniline (PANI) composite films with enhanced thermoelectric properties were prepared by combining in situ polymerization and solution processing. Conductive atomic force microscopy and X-ray diffraction measurements confirmed that solution processing and strong π-π interactions between the PANI and SWNTs induced the PANI molecules to form a highly ordered structure. The improved degree of order of the PANI molecular arrangement increased the carrier mobility and thereby enhanced the electrical transport properties of PANI. The maximum in-plane electrical conductivity and power factor of the SWNTs/PANI composite films reached 1.44×10(3)  S cm(-1) and 217 μW m(-1)  K(-2) , respectively, at room temperature. Furthermore, a thermoelectric generator fabricated with the SWNTs/PANI composite films showed good electric generation ability and stability. A high power density of 10.4 μW cm(-2)  K(-1) was obtained, which is superior to most reported results obtained in organic thermoelectric modules.

  19. Carbon nanotube materials for hydrogen storage

    Energy Technology Data Exchange (ETDEWEB)

    Dillon, A.C.; Parilla, P.A.; Jones, K.M.; Riker, G.; Heben, M.J. [National Renewable Energy Lab., Golden, CO (United States)

    1998-08-01

    Carbon single-wall nanotubes (SWNTs) are essentially elongated pores of molecular dimensions and are capable of adsorbing hydrogen at relatively high temperatures and low pressures. This behavior is unique to these materials and indicates that SWNTs are the ideal building block for constructing safe, efficient, and high energy density adsorbents for hydrogen storage applications. In past work the authors developed methods for preparing and opening SWNTs, discovered the unique adsorption properties of these new materials, confirmed that hydrogen is stabilized by physical rather than chemical interactions, measured the strength of interaction to be {approximately} 5 times higher than for adsorption on planar graphite, and performed infrared absorption spectroscopy to determine the chemical nature of the surface terminations before, during, and after oxidation. This year the authors have made significant advances in synthesis and characterization of SWNT materials so that they can now prepare gram quantities of high-purity SWNT samples and measure and control the diameter distribution of the tubes by varying key parameters during synthesis. They have also developed methods which purify nanotubes and cut nanotubes into shorter segments. These capabilities provide a means for opening the tubes which were unreactive to the oxidation methods that successfully opened tubes, and offer a path towards organizing nanotube segments to enable high volumetric hydrogen storage densities. They also performed temperature programmed desorption spectroscopy on high purity carbon nanotube material obtained from collaborator Prof. Patrick Bernier and finished construction of a high precision Seivert`s apparatus which will allow the hydrogen pressure-temperature-composition phase diagrams to be evaluated for SWNT materials.

  20. SURFACE MORPHOLOGY OF CARBON FIBER POLYMER COMPOSITES AFTER LASER STRUCTURING

    Energy Technology Data Exchange (ETDEWEB)

    Sabau, Adrian S [ORNL; Chen, Jian [ORNL; Jones, Jonaaron F. [University of Tennessee (UT); Alexandra, Hackett [University of Tennessee (UT); Jellison Jr, Gerald Earle [ORNL; Daniel, Claus [ORNL; Warren, Charles David [ORNL; Rehkopf, Jackie D. [Plasan Carbon Composites

    2015-01-01

    The increasing use of Carbon Fiber Polymer Composite (CFPC) as a lightweight material in automotive and aerospace industries requires the control of surface morphology. In this study, the composites surface was prepared by ablating the resin in the top fiber layer of the composite using an Nd:YAG laser. The CFPC specimens with T700S carbon fiber and Prepreg - T83 resin (epoxy) were supplied by Plasan Carbon Composites, Inc. as 4 ply thick, 0/90o plaques. The effect of laser fluence, scanning speed, and wavelength was investigated to remove resin without an excessive damage of the fibers. In addition, resin ablation due to the power variation created by a laser interference technique is presented. Optical property measurements, optical micrographs, 3D imaging, and high-resolution optical profiler images were used to study the effect of the laser processing on the surface morphology.

  1. Puncture-Healing Thermoplastic Resin Carbon-Fiber-Reinforced Composites

    Science.gov (United States)

    Gordon, Keith L. (Inventor); Siochi, Emilie J. (Inventor); Grimsley, Brian W. (Inventor); Cano, Roberto J. (Inventor); Czabaj, Michael W. (Inventor)

    2015-01-01

    A composite comprising a combination of a self-healing polymer matrix and a carbon fiber reinforcement is described. In one embodiment, the matrix is a polybutadiene graft copolymer matrix, such as polybutadiene graft copolymer comprising poly(butadiene)-graft-poly(methyl acrylate-co-acrylonitrile). A method of fabricating the composite is also described, comprising the steps of manufacturing a pre-impregnated unidirectional carbon fiber preform by wetting a plurality of carbon fibers with a solution, the solution comprising a self-healing polymer and a solvent, and curing the preform. A method of repairing a structure made from the composite of the invention is described. A novel prepreg material used to manufacture the composite of the invention is described.

  2. Stiffness analysis of the sarafix external fixator of composite materials

    Directory of Open Access Journals (Sweden)

    Nedim Pervan

    2016-01-01

    Full Text Available This paper describes a structural analysis of the CAD model three versions fixators Sarafix which to explore the possibility of introducing composite materials in the construction of the connecting rod fixators comparing values of displacement and stiffness at characteristic points structure. Namely, we investigated constructional performance of fixators Sarafix with a connecting rod formed from three different composite materials, the same matrix (epoxy resin with three different types of fibers (E glass, kevlar 49 and carbon M55J. Results of structural analysis fixators Sarafix with a connecting rod made of composite materials are compared with the results of tubular connecting rod fixators made of stainless steel. After comparing the results, from the aspect of stiffness, we gave the final considerations about composite material which provides an adequate substitution for the existing material.

  3. [Carbon fiber reinforced polysulfone--a new implant material].

    Science.gov (United States)

    Claes, L

    1989-12-01

    Carbon fibre reinforced polysulfone is a composite material which contains two materials of well known biocompatibility. In comparison to metals this composite material has some advantages which makes it favourable particularly for implants in tumor surgery. The custom made arrangement of fibres in the composite allows the development of implants with special mechanical properties. The radiolucency of the material avoids problems caused by the reflection of x-rays, using metal implants. This special property allows the exact calculation of postoperative radiation doses of tumor patients. Simultaneously the structures behind the implants are not hidden. All implants can be machined during the operation to adapt them to the individual anatomical situation. Animal experimental and clinical applications of plates, screws and spinal segmental replacement implants made of this composite material have shown good results so far.

  4. Computer-Aided Process Model For Carbon/Phenolic Materials

    Science.gov (United States)

    Letson, Mischell A.; Bunker, Robert C.

    1996-01-01

    Computer program implements thermochemical model of processing of carbon-fiber/phenolic-matrix composite materials into molded parts of various sizes and shapes. Directed toward improving fabrication of rocket-engine-nozzle parts, also used to optimize fabrication of other structural components, and material-property parameters changed to apply to other materials. Reduces costs by reducing amount of laboratory trial and error needed to optimize curing processes and to predict properties of cured parts.

  5. Piezoelectric Nanoparticle-Polymer Composite Materials

    Science.gov (United States)

    McCall, William Ray

    Herein we demonstrate that efficient piezoelectric nanoparticle-polymer composite materials can be synthesized and fabricated into complex microstructures using sugar-templating methods or optical printing techniques. Stretchable foams with excellent tunable piezoelectric properties are created by incorporating sugar grains directly into polydimethylsiloxane (PDMS) mixtures containing barium titanate (BaTiO3 -- BTO) nanoparticles and carbon nanotubes (CNTs), followed by removal of the sugar after polymer curing. Porosities and elasticity are tuned by simply adjusting the sugar/polymer mass ratio and the electrical performance of the foams showed a direct relationship between porosity and the piezoelectric outputs. User defined 2D and 3D optically printed piezoelectric microstructures are also fabricated by incorporating BTO nanoparticles into photoliable polymer solutions such as polyethylene glycol diacrylate (PEGDA) and exposing to digital optical masks that can be dynamically altered. Mechanical-to-electrical conversion efficiency of the optically printed composite is enhanced by chemically altering the surface of the BTO nanoparticles with acrylate groups which form direct covalent linkages with the polymer matrix under light exposure. Both of these novel materials should find exciting uses in a variety of applications including energy scavenging platforms, nano- and microelectromechanical systems (NEMS/MEMS), sensors, and acoustic actuators.

  6. Modeling of Moisture Diffusion in Carbon Braided Composites

    Directory of Open Access Journals (Sweden)

    S. Laurenzi

    2008-01-01

    Full Text Available In this study, we develop a methodology based on finite element analysis to predict the weight gain of carbon braided composite materials exposed to moisture. The analysis was based on the analogy between thermal conduction and diffusion processes, which allowed for a commercial code for finite element analysis to be used. A detailed finite element model using a repetitive unit cell (RUC was developed both for bundle and carbon braided composites. Conditioning tests were performed to estimate the diffusivity of both the resin and composite. When comparing numerical and experimental results, it was observed that the procedure introduces an average error of 20% and a maximum error of 31% if the RUC is assumed to be isotropic. On the other hand, the average error does not exceed 10% and the maximum error is less than 20% when the material is considered as orthotropic. The procedure is independent of the particular fiber architecture and can be extended to other composites.

  7. Carbon fiber content measurement in composite

    Science.gov (United States)

    Wang, Qiushi

    Carbon fiber reinforced polymers (CFRPs) have been widely used in various structural applications in industries such as aerospace and automotive because of their high specific stiffness and specific strength. Their mechanical properties are strongly influenced by the carbon fiber content in the composites. Measurement of the carbon fiber content in CFRPs is essential for product quality control and process optimization. In this work, a novel carbonization-in-nitrogen method (CIN) is developed to characterize the fiber content in carbon fiber reinforced thermoset and thermoplastic composites. In this method, a carbon fiber composite sample is carbonized in a nitrogen environment at elevated temperatures, alongside a neat resin sample. The carbon fibers are protected from oxidization while the resin (the neat resin and the resin matrix in the composite sample) is carbonized under the nitrogen environment. The residue of the carbonized neat resin sample is used to calibrate the resin carbonization rate and calculate the amount of the resin matrix in the composite sample. The new method has been validated on several thermoset and thermoplastic resin systems and found to yield an accurate measurement of fiber content in carbon fiber polymer composites. In order to further understand the thermal degradation behavior of the high temperature thermoplastic polymer during the carbonization process, the mechanism and the kinetic model of thermal degradation behavior of carbon fiber reinforced poly (phenylene sulfide) (CPPS) are studied using thermogravimetry analysis (TGA). The CPPS is subjected to TGA in an air and nitrogen atmosphere at heating rates from 5 to 40°C min--1. The TGA curves obtained in air are different from those in nitrogen. This demonstrates that weight loss occurs in a single stage in nitrogen but in two stages in air. To elucidate this difference, thermal decomposition kinetics is analyzed by applying the Kissinger, Flynn-Wall-Ozawa, Coat-Redfern and

  8. Advanced Carbon Materials for Environmental and Energy Applications

    KAUST Repository

    Dua, Rubal

    2014-05-01

    Carbon based materials, including porous carbons and carbon layer composites, are finding increased usage in latest environmental and energy related research. Among porous carbon materials, hierarchical porous carbons with multi-modal porosity are proving out to be an effective solution for applications where the traditional activated carbons fail. Thus, there has been a lot of recent interest in developing low-cost, facile, easy to scale-up, synthesis techniques for producing such multi-modal porous carbons. This dissertation offers two novel synthesis techniques: (i) ice templating integrated with hard templating, and (ii) salt templating coupled with hard templating, for producing such hierarchically porous carbons. The techniques offer tight control and tunability of porosity (macro- meso- and microscale) in terms of both size and extent. The synthesized multi-modal porous carbons are shown to be an effective solution for three important environment related applications – (i) Carbon dioxide capture using amine supported hierarchical porous carbons, (ii) Reduction in irreversible fouling of membranes used for wastewater reuse through a deposition of a layer of hierarchical porous carbons on the membrane surface, (iii) Electrode materials for electrosorptive applications. Finally, because of their tunability, the synthesized multi-modal porous carbons serve as excellent model systems for understanding the effect of different types of porosity on the performance of porous carbons for these applications. Also, recently, there has been a lot of interest in developing protective layer coatings for preventing photo-corrosion of semiconductor structures (in particular Cu2O) used for photoelectrochemical water splitting. Most of the developed protective strategies to date involve the use of metals or co-catalyst in the protective layer. Thus there is a big need for developing low-cost, facile and easy to scale protective coating strategies. Based on the expertise

  9. A carbon fibre composite (CFC) Byelorussian peat corer

    OpenAIRE

    2009-01-01

    The design specification, development and manufacture of a Byelorussian (Russian) peat corer constructed from carbon fibre composite (CFC) are described. The availability of this new composite material introduces new possibilities for constructing field instruments that are as strong as, or stronger than, equipment made from steel and other metals. One advantage is a significant weight reduction. A 10.5 metre coring set in standard stainless and soft steel weighs around 16 kg, whereas the tot...

  10. Applications of Nanostructured Carbon Materials in Constructions: The State of the Art

    Directory of Open Access Journals (Sweden)

    Shu-Nan Lu

    2015-01-01

    Full Text Available The most recent studies on the applications of nanostructured carbon materials, including carbon nanotubes, carbon nanofibers, and graphene oxides, in constructions are presented. First, the preparation of nanostructured carbon/infrastructure material composites is summarized. This part is mainly focused on how the nanostructured carbon materials were mixed with cementitious or asphalt matrix to realize a good dispersion condition. Several methods, including high speed melting mixing, surface treatment, and aqueous solution with surfactants and sonication, were introduced. Second, the applications of the carbon nanostructured materials in constructions such as mechanical reinforcement, self-sensing detectors, self-heating element for deicing, and electromagnetic shielding component were systematically reviewed. This paper not only helps the readers understand the preparation process of the carbon nanostructured materials/infrastructure material composites but also sheds some light on the state-of-the-art applications of carbon nanostructured materials in constructions.

  11. Structural and biological properties of carbon nanotube composite films

    Energy Technology Data Exchange (ETDEWEB)

    Narayan, Roger J. [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0245 (United States)]. E-mail: roger.narayan@mse.gatech.edu; Berry, C.J. [Environmental Biotechnology Section, Savannah River National Laboratory, Aiken, SC 29808 (United States); Brigmon, R.L. [Environmental Biotechnology Section, Savannah River National Laboratory, Aiken, SC 29808 (United States)

    2005-11-20

    Carbon nanotube composite films have been developed that exhibit unusual structural and biological properties. These novel materials have been created by pulsed laser ablation of graphite and bombardment of nitrogen ions at temperatures between 600 and 700 deg. C. High-resolution transmission electron microscopy and radial distribution function analysis demonstrate that this material consists of sp{sup 2}-bonded concentric ribbons that are wrapped approximately 15 deg. normal to the silicon substrate. The interlayer order in this material extends to approximately 15-30 A. X-ray photoelectron spectroscopy and Raman spectroscopy data suggest that this material is predominantly trigonally coordinated. The carbon nanotube composite structure results from the use of energetic ions, which allow for non-equilibrium growth of graphitic planes. In vitro testing has revealed significant antimicrobial activity of carbon nanotube composite films against Staphylococcus aureus and Staphylococcus warneri colonization. Carbon nanotube composite films may be useful for inhibiting microorganism attachment and biofilm formation in hemodialysis catheters and other medical devices.

  12. 锂离子电池锡-碳复合负极材料的研究进展%Research progress of tin-carbon composite anode material for Li-ion battery

    Institute of Scientific and Technical Information of China (English)

    任建国; 闫润宝; 何向明; 蒲薇华; 赵海雷

    2011-01-01

    With the advantage of high capacity and high density, alloy materials are expected to be the preferred anode materials for next-generation lithium-ion battery with high energy density. The great volume expansion/contraction during lithiation/delithiation leads to the cracking and pulverizing of alloy material. With the loss of electronic contact within the pulverized alloy particles, the capacity of alloy anode fades rapidly. The nanostructured composite is an ideal choice to improve the cycling stability of alloy anode material. The research progress of Sn-based alloy-carbon composite anode materials for Li-ion battery was reviewed in this paper. It is pointed out that alloy/carbon composite is an effective way for improving the cycling performance of Sn-based alloy anode.%合金材料具有高容量、高密度的优势,有望成为新一代高容量锂离子电池的负极材料.合金材料在锂化过程中产生较大的体积膨胀,易开裂粉化,活性物质内部丧失电接触,电极容量衰减迅速.米复合结构是提高合金负极材料循环稳定性的有效途径.述了锂离子电池Sn基合金-碳复合负极材料的研究进展,指出纳米合金-碳复合结构是提高Sn基合金负极循环性能的有效手段.

  13. Facile Synthesis of Carbon-Coated Spinel Li4Ti5O12/Rutile-TiO2 Composites as an Improved Anode Material in Full Lithium-Ion Batteries with LiFePO4@N-Doped Carbon Cathode.

    Science.gov (United States)

    Wang, Ping; Zhang, Geng; Cheng, Jian; You, Ya; Li, Yong-Ke; Ding, Cong; Gu, Jiang-Jiang; Zheng, Xin-Sheng; Zhang, Chao-Feng; Cao, Fei-Fei

    2017-02-22

    The spinel Li4Ti5O12/rutile-TiO2@carbon (LTO-RTO@C) composites were fabricated via a hydrothermal method combined with calcination treatment employing glucose as carbon source. The carbon coating layer and the in situ formed rutile-TiO2 can effectively enhance the electric conductivity and provide quick Li(+) diffusion pathways for Li4Ti5O12. When used as an anode material for lithium-ion batteries, the rate capability and cycling stability of LTO-RTO@C composites were improved in comparison with those of pure Li4Ti5O12 or Li4Ti5O12/rutile-TiO2. Moreover, the potential of approximately 1.8 V rechargeable full lithium-ion batteries has been achieved by utilizing an LTO-RTO@C anode and a LiFePO4@N-doped carbon cathode.

  14. Analysis of composition and microstructural uniformity of hybrid glass/carbon fibre composites

    DEFF Research Database (Denmark)

    Beauson, Justine; Markussen, Christen Malte; Madsen, Bo

    2013-01-01

    In hybrid fibre composites, the intermixing of the two types of fibres imposes challenges to obtain materials with a well-defined and uniform microstructure. In the present paper, the composition and the microstructural uniformity of hybrid glass/carbon fibre composites mixed at the fibre bundle...... fibre volume fractions are determined using volumetric calculations. A model is presented to predict the interrelation of volume fractions in hybrid fibre composites. The microstructural uniformity of the composites is analysed by the determined variation in composite volume fractions. Two analytical...... level are investigated. The different levels of compositions in the composites are defined and experimentally determined. The composite volume fractions are determined using an image analysis based procedure. The global fibre volume fractions are determined using a gravimetrical based method. The local...

  15. Radiation curing of carbon fibre composites

    Science.gov (United States)

    Spadaro, G.; Alessi, S.; Dispenza, C.; Sabatino, M. A.; Pitarresi, G.; Tumino, D.; Przbytniak, G.

    2014-01-01

    Epoxy/carbon fibre reinforced composites were produced by means of e-beam irradiation through a pulsed 10 MeV electron beam accelerator. The matrix consisted of a difunctional epoxy monomer (DGEBA) and an initiator of cationic polymerisation, while the reinforcement was a unidirectional high modulus carbon fibre fabric. Dynamic mechanical thermal analysis was carried out in order to determine the cross-linking degree. The analysis pointed out a nonuniformity in the cross-linking degree of the e-beam cured panels, with the formation of clusters at low Tg (glass transition temperature) and clusters at high Tg. An out-of-mould post irradiation thermal treatment on e-beam cured samples provides a higher uniformity in the network although some slight degradation effects. Mode I delamination fracture toughness and Interlaminar Shear Strength (ISS) were also investigated by means of Double Cantilever Beam (DCB) and Short Beam Shear tests, respectively. Results from this mechanical characterisation allowed to correlate fracture toughness of the bulk matrix resin, cross-linking density and fibre/matrix interaction to the delamination fracture behaviour of the fibre reinforced material.

  16. Modification of the Interfacial Interaction between Carbon Fiber and Epoxy with Carbon Hybrid Materials

    Directory of Open Access Journals (Sweden)

    Kejing Yu

    2016-05-01

    Full Text Available The mechanical properties of the hybrid materials and epoxy and carbon fiber (CF composites were improved significantly as compared to the CF composites made from unmodified epoxy. The reasons could be attributed to the strong interfacial interaction between the CF and the epoxy composites for the existence of carbon nanomaterials. The microstructure and dispersion of carbon nanomaterials were characterized by transmission electron microscopy (TEM and optical microscopy (OM. The results showed that the dispersion of the hybrid materials in the polymer was superior to other carbon nanomaterials. The high viscosity and shear stress characterized by a rheometer and the high interfacial friction and damping behavior characterized by dynamic mechanical analysis (DMA indicated that the strong interfacial interaction was greatly improved between fibers and epoxy composites. Remarkably, the tensile tests presented that the CF composites with hybrid materials and epoxy composites have a better reinforcing and toughening effect on CF, which further verified the strong interfacial interaction between epoxy and CF for special structural hybrid materials.

  17. Carbon Nanotube Composites for Electronic Packaging Applications: A Review

    Directory of Open Access Journals (Sweden)

    Lavanya Aryasomayajula

    2013-01-01

    Full Text Available Composite engineering comprises of metal matrix composites. They have high strength-weight ratio, better stiffness, economical production, and ease of availability of raw materials. The discovery of carbon nanotubes has opened new possibilities to face challenges better. Carbon Nanotubes are known for their high mechanical strength, excellent thermal and electrical properties. Recent research has made progress in fabricating carbon nanotube metal matrix and polymer-based composites. The methods of fabrication of these composites, their properties and possible applications restricted to the field of electronic packaging have been discussed in this paper. Experimental and theoretical calculations have shown improved mechanical and physical properties like tensile stress, toughness, and improved electrical and thermal properties. They have also demonstrated the ease of production of the composites and their adaptability as one can tailor their properties as per the requirement. This paper reviews work reported on fabricating and characterizing carbon- nanotube-based metal matrix and polymer composites. The focus of this paper is mainly to review the importance of these composites in the field of electronics packaging.

  18. DOE Automotive Composite Materials Research: Present and Future Efforts

    Energy Technology Data Exchange (ETDEWEB)

    Warren, C.D.

    1999-08-10

    One method of increasing automotive energy efficiency is through mass reduction of structural components by the incorporation of composite materials. Significant use of glass reinforced polymers as structural components could yield a 20--30% reduction in vehicle weight while the use of carbon fiber reinforced materials could yield a 40--60% reduction in mass. Specific areas of research for lightweighting automotive components are listed, along with research needs for each of these categories: (1) low mass metals; (2) polymer composites; and (3) ceramic materials.

  19. Smart Behavior of Carbon Fiber Reinforced Cement-based Composite

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The electrical characteristics of cement-based material can be remarkably improved by the addition of short carbon fibers.Carbon fiber reinforced cement composite (CFRC) is an intrinsically smart material that can sense not only the stress andstrain, but also the temperature. In this paper, variations of electrical resistivity with external applied load, and relationof thermoelectric force and temperature were investigated. Test results indicated that the electrical signal is related to theincrease in the material volume resistivity during crack generation or propagation and the decrease in the resistivity duringcrack closure. Moreover, it was found that the fiber addition increased the linearity and reversibility of the Seebeck effect inthe cement-based materials. The change of electrical characteristics reflects large amount of information of inner damage andtemperature differential of composite, which can be used for stress-strain or thermal self-monitoring by embedding it in theconcrete structures.

  20. Multifunctional Hybrid Carbon Nanotube/Carbon Fiber Polymer Composites

    Science.gov (United States)

    Kang, Jin Ho; Cano, Roberto J.; Ratcliffe, James G.; Luong, Hoa; Grimsley, Brian W.; Siochi, Emilie J.

    2016-01-01

    For aircraft primary structures, carbon fiber reinforced polymer (CFRP) composites possess many advantages over conventional aluminum alloys due to their light weight, higher strengthand stiffness-to-weight ratio, and low life-cycle maintenance costs. However, the relatively low electrical and thermal conductivities of CFRP composites fail to provide structural safety in certain operational conditions such as lightning strikes. Despite several attempts to solve these issues with the addition of carbon nanotubes (CNT) into polymer matrices, and/or by interleaving CNT sheets between conventional carbon fiber (CF) composite layers, there are still interfacial problems that exist between CNTs (or CF) and the resin. In this study, hybrid CNT/CF polymer composites were fabricated by interleaving layers of CNT sheets with Hexcel® IM7/8852 prepreg. Resin concentrations from 1 wt% to 50 wt% were used to infuse the CNT sheets prior to composite fabrication. The interlaminar properties of the resulting hybrid composites were characterized by mode I and II fracture toughness testing (double cantilever beam and end-notched flexure test). Fractographical analysis was performed to study the effect of resin concentration. In addition, multi-directional physical properties like thermal conductivity of the orthotropic hybrid polymer composite were evaluated. Interleaving CNT sheets significantly improved the in-plane (axial and perpendicular direction of CF alignment) thermal conductivity of the hybrid composite laminates by 50 - 400%.

  1. Composite materials for battery applications

    Energy Technology Data Exchange (ETDEWEB)

    Amine, Khalil; Yang, Junbing; Abouimrane, Ali; Ren, Jianguo

    2017-03-14

    A process for producing nanocomposite materials for use in batteries includes electroactive materials are incorporated within a nanosheet host material. The process may include treatment at high temperatures and doping to obtain desirable properties.

  2. Processing of thermo-structural carbon-fiber reinforced carbon composites

    Directory of Open Access Journals (Sweden)

    Luiz Cláudio Pardini

    2009-06-01

    Full Text Available The present work describes the processes used to obtain thermostructural Carbon/Carbon composites. The processing of these materials begins with the definition of the architecture of the carbon fiber reinforcement, in the form of stacked plies or in the form of fabrics or multidirectional reinforcement. Incorporating fiber reinforcement into the carbon matrix, by filling the voids and interstices, leads to the densification of the material and a continuous increase in density. There are two principal processing routes for obtaining these materials: liquid phase processing and gas phase processing. In both cases, thermal processes lead to the formation of a carbon matrix with specific properties related to their precursor. These processes also differ in terms of yield. With liquid phase impregnation the yield is around 45 per cent, while gas phase processing yields around 15 per cent.

  3. Homogeneous Carbon Nanotube/Carbon Composites Prepared by Catalyzed Carbonization Approach at Low Temperature

    Directory of Open Access Journals (Sweden)

    Hongjiang Li

    2011-01-01

    Full Text Available We synthesize carbon nanotube (CNT/carbon composite using catalyzed carbonization of CNT/Epoxy Resin composite at a fairly low temperature of about 400∘C. The microstructure of the composite is characterized by scanning electron microscope (SEM, transmission electron microscope (TEM, and X-ray diffraction (XRD. The results indicate that CNTs and pyrolytic carbon blend well with each other. Pyrolytic carbon mainly stays in an amorphous state, with some of it forming crystalline structures. The catalyst has the effect of eliminating the interstices in the composites. Remarkable increases in thermal and electrical conductivity are also reported.

  4. Mechanical testing and modelling of carbon-carbon composites for aircraft disc brakes

    Science.gov (United States)

    Bradley, Luke R.

    The objective of this study is to improve the understanding of the stress distributions and failure mechanisms experienced by carbon-carbon composite aircraft brake discs using finite element (FE) analyses. The project has been carried out in association with Dunlop Aerospace as an EPSRC CASE studentship. It therefore focuses on the carbon-carbon composite brake disc material produced by Dunlop Aerospace, although it is envisaged that the approach will have broader applications for modelling and mechanical testing of carbon-carbon composites in general. The disc brake material is a laminated carbon-carbon composite comprised of poly(acrylonitrile) (PAN) derived carbon fibres in a chemical vapour infiltration (CVI) deposited matrix, in which the reinforcement is present in both continuous fibre and chopped fibre forms. To pave the way for the finite element analysis, a comprehensive study of the mechanical properties of the carbon-carbon composite material was carried out. This focused largely, but not entirely, on model composite materials formulated using structural elements of the disc brake material. The strengths and moduli of these materials were measured in tension, compression and shear in several orientations. It was found that the stress-strain behaviour of the materials were linear in directions where there was some continuous fibre reinforcement, but non-linear when this was not the case. In all orientations, some degree of non-linearity was observed in the shear stress-strain response of the materials. However, this non-linearity was generally not large enough to pose a problem for the estimation of elastic moduli. Evidence was found for negative Poisson's ratio behaviour in some orientations of the material in tension. Additionally, the through-thickness properties of the composite, including interlaminar shear strength, were shown to be positively related to bulk density. The in-plane properties were mostly unrelated to bulk density over the range of

  5. Carbon nanotube and conducting polymer composites for supercapacitors

    Institute of Scientific and Technical Information of China (English)

    Chuang Peng; Shengwen Zhang; Daniel Jewell; George Z. Chen

    2008-01-01

    Composites of carbon nanotubes and conducting polymers can be prepared via chemical synthesis, electrochemical deposition on pre-formed carbon nanotube electrodes, or by electrochemical co-deposition. The composites combine the large pseudocapacitance of the conducting polymers with the fast charging/discharging double-layer capacitance and excellent mechanical properties of the carbon nanotubes. The electrochemically co-deposited composites are the most homogeneous and show an unusual interaction between thepolymer and nanotubes, giving rise to a strengthened electron delocalisation and conjugation along the polymer chains. As a result they exhibit excellent electrochemical charge storage properties and fast charge/discharge switching, making them promising electrode mate-rials for high power supercapacitors.

  6. Changes in the Thermal and Dimensional Stability of the Structure of a Polymer Composite After Carbonization

    Science.gov (United States)

    Gaidachuk, V. E.; Kondratiev, A. V.; Chesnokov, A. V.

    2017-01-01

    Based on the theory of reinforcement of polymer composites, approximate relations for the physicomechanical and strength properties of a carbon-carbon composite material are synthesized, which are used to perform a finite-element analysis of the degree and character of changes in the thermal and dimensional stability of its structure after carbonization. Using approximate criteria of structural optimization of carbon-carbon composites ensuring their maximum dimensional stability, a [0/±45/90] package of thermally nonquilibrium layers is investigated and compared with an analogous carbon-fiber-reinforced plastic.

  7. Carbon nanotube integrated multifunctional multiscale composites

    Energy Technology Data Exchange (ETDEWEB)

    Qiu Jingjing; Zhang, Chuck; Wang, Ben; Liang, Richard [High-Performance Materials Institute, Department of Industrial and Manufacturing Engineering, Florida A and M University-Florida State University College of Engineering, 2525 Pottsdamer Street, Tallahassee, FL 32310-6046 (United States)

    2007-07-11

    Carbon nanotubes (CNTs) demonstrate extraordinary properties and show great promise in enhancing out-of-plane properties of traditional polymer composites and enabling functionality, but current manufacturing challenges hinder the realization of their potential. This paper presents a method to fabricate multifunctional multiscale composites through an effective infiltration-based vacuum-assisted resin transfer moulding (VARTM) process. Multi-walled carbon nanotubes (MWNTs) were infused through and between glass-fibre tows along the through-thickness direction. Both pristine and functionalized MWNTs were used in fabricating multiscale glass-fibre-reinforced epoxy composites. It was demonstrated that the mechanical properties of multiscale composites were remarkably enhanced, especially in the functionalized MWNT multiscale composites. With only 1 wt% loading of functionalized MWNTs, tensile strength was increased by 14% and Young's modulus by 20%, in comparison with conventional fibre-reinforced composites. Moreover, the shear strength and short-beam modulus were increased by 5% and 8%, respectively, indicating the improved inter-laminar properties. The strain-stress tests also suggested noticeable enhancement in toughness. Scanning electron microscopy (SEM) characterization confirmed an enhanced interfacial bonding when functionalized MWNTs were integrated into epoxy/glass-fibre composites. The coefficient thermal expansion (CTE) of functionalized nanocomposites indicated a reduction of 25.2% compared with epoxy/glass-fibre composites. The desired improvement of electrical conductivities was also achieved. The multiscale composites indicated a way to leverage the benefits of CNTs and opened up new opportunities for high-performance multifunctional multiscale composites.

  8. Carbon nanotube integrated multifunctional multiscale composites

    Science.gov (United States)

    Qiu, Jingjing; Zhang, Chuck; Wang, Ben; Liang, Richard

    2007-07-01

    Carbon nanotubes (CNTs) demonstrate extraordinary properties and show great promise in enhancing out-of-plane properties of traditional polymer composites and enabling functionality, but current manufacturing challenges hinder the realization of their potential. This paper presents a method to fabricate multifunctional multiscale composites through an effective infiltration-based vacuum-assisted resin transfer moulding (VARTM) process. Multi-walled carbon nanotubes (MWNTs) were infused through and between glass-fibre tows along the through-thickness direction. Both pristine and functionalized MWNTs were used in fabricating multiscale glass-fibre-reinforced epoxy composites. It was demonstrated that the mechanical properties of multiscale composites were remarkably enhanced, especially in the functionalized MWNT multiscale composites. With only 1 wt% loading of functionalized MWNTs, tensile strength was increased by 14% and Young's modulus by 20%, in comparison with conventional fibre-reinforced composites. Moreover, the shear strength and short-beam modulus were increased by 5% and 8%, respectively, indicating the improved inter-laminar properties. The strain-stress tests also suggested noticeable enhancement in toughness. Scanning electron microscopy (SEM) characterization confirmed an enhanced interfacial bonding when functionalized MWNTs were integrated into epoxy/glass-fibre composites. The coefficient thermal expansion (CTE) of functionalized nanocomposites indicated a reduction of 25.2% compared with epoxy/glass-fibre composites. The desired improvement of electrical conductivities was also achieved. The multiscale composites indicated a way to leverage the benefits of CNTs and opened up new opportunities for high-performance multifunctional multiscale composites.

  9. Dispersion of Carbon Nanotubes: Mixing, Sonication, Stabilization, and Composite Properties

    Directory of Open Access Journals (Sweden)

    Eugene M. Terentjev

    2012-01-01

    Full Text Available Advances in functionality and reliability of carbon nanotube (CNT composite materials require careful formulation of processing methods to ultimately realize the desired properties. To date, controlled dispersion of CNTs in a solution or a composite matrix remains a challenge, due to the strong van der Waals binding energies associated with the CNT aggregates. There is also insufficiently defined correlation between the microstructure and the physical properties of the composite. Here, we offer a review of the dispersion processes of pristine (non-covalently functionalized CNTs in a solvent or a polymer solution. We summarize and adapt relevant theoretical analysis to guide the dispersion design and selection, from the processes of mixing/sonication, to the application of surfactants for stabilization, to the final testing of composite properties. The same approaches are expected to be also applicable to the fabrication of other composite materials involving homogeneously dispersed nanoparticles.

  10. Structural Analysis of Novel Lignin-derived Carbon Composite Anodes

    Energy Technology Data Exchange (ETDEWEB)

    McNutt, Nicholas W [ORNL; Rios, Orlando [ORNL; Feygenson, Mikhail [ORNL; Proffen, Thomas E [ORNL; Keffer, David J [ORNL

    2014-01-01

    The development of novel lignin-based carbon composite anodes consisting of nanocrystalline and amorphous domains motivates the understanding of a relationship of the structural properties characterizing these materials, such as crystallite size, intracrystallite dspacing, crystalline volume fraction and composite density, with their pair distribution functions (PDF), obtained from both molecular dynamics simulation and neutron scattering. A model for these composite materials is developed as a function of experimentally measurable parameters and realized in fifteen composite systems, three of which directly match all parameters of their experimental counterparts. The accurate reproduction of the experimental PDFs using the model systems validates the model. The decomposition of the simulated PDFs provides an understanding of each feature in the PDF and allows for the development of a mapping between the defining characteristics of the PDF and the material properties of interest.

  11. Fischer-Tropsch synthesis on hierarchically structured cobalt nanoparticle/carbon nanofiber/carbon felt composites.

    Science.gov (United States)

    Zarubova, Sarka; Rane, Shreyas; Yang, Jia; Yu, Yingda; Zhu, Ye; Chen, De; Holmen, Anders

    2011-07-18

    The hierarchically structured carbon nanofibers (CNFs)/carbon felt composites, in which CNFs were directly grown on the surface of microfibers in carbon felt, forming a CNF layer on a micrometer range that completely covers the microfiber surfaces, were tested as a novel support material for cobalt nanoparticles in the highly exothermic Fischer-Tropsch (F-T) synthesis. A compact, fixed-bed reactor, made of disks of such composite materials, offered the advantages of improved heat and mass transfer, relatively low pressure drop, and safe handling of immobilized CNFs. An efficient 3-D thermal conductive network in the composite provided a relatively uniform temperature profile, whereas the open structure of the CNF layer afforded an almost 100 % effectiveness of Co nanoparticles in the F-T synthesis in the fixed bed. The greatly improved mass and heat transport makes the compact reactor attractive for applications in the conversion of biomass, coal, and natural gas to liquids.

  12. Clues for biomimetics from natural composite materials

    Science.gov (United States)

    Lapidot, Shaul; Meirovitch, Sigal; Sharon, Sigal; Heyman, Arnon; Kaplan, David L; Shoseyov, Oded

    2013-01-01

    Bio-inspired material systems are derived from different living organisms such as plants, arthropods, mammals and marine organisms. These biomaterial systems from nature are always present in the form of composites, with molecular-scale interactions optimized to direct functional features. With interest in replacing synthetic materials with natural materials due to biocompatibility, sustainability and green chemistry issues, it is important to understand the molecular structure and chemistry of the raw component materials to also learn from their natural engineering, interfaces and interactions leading to durable and highly functional material architectures. This review will focus on applications of biomaterials in single material forms, as well as biomimetic composites inspired by natural organizational features. Examples of different natural composite systems will be described, followed by implementation of the principles underlying their composite organization into artificial bio-inspired systems for materials with new functional features for future medicine. PMID:22994958

  13. Carbon-carbon composites for orthopedic prosthesis and implants. CRADA final report

    Energy Technology Data Exchange (ETDEWEB)

    Burchell, T D; Klett, J W; Strizak, J P [Oak Ridge National Lab., TN (United States); Baker, C [FMI, Biddeford, ME (United States)

    1998-01-21

    The prosthetic implant market is extensive. For example, because of arthritic degeneration of hip and knee cartilage and osteoporotic fractures of the hip, over 200,000 total joint replacements (TJRs) are performed in the United States each year. Current TJR devices are typically metallic (stainless steel, cobalt, or titanium alloy) and are fixed in the bone with polymethylacrylate (PMMA) cement. Carbon-carbon composite materials offer several distinct advantages over metals for TJR prosthesis. Their mechanical properties can be tailored to match more closely the mechanical properties of human bone, and the composite may have up to 25% porosity, the size and distribution of which may be controlled through processing. The porous nature of carbon-carbon composites will allow for the ingrowth of bone, achieving biological fixation, and eliminating the need for PMMA cement fixation.

  14. Review on advanced composite materials boring mechanism and tools

    Science.gov (United States)

    Shi, Runping; Wang, Chengyong

    2011-05-01

    With the rapid development of aviation and aerospace manufacturing technology, advanced composite materials represented by carbon fibre reinforced plastics (CFRP) and super hybrid composites (fibre/metal plates) are more and more widely applied. The fibres are mainly carbon fibre, boron fibre, Aramid fiber and Sic fibre. The matrixes are resin matrix, metal matrix and ceramic matrix. Advanced composite materials have higher specific strength and higher specific modulus than glass fibre reinforced resin composites of the 1st generation. They are widely used in aviation and aerospace industry due to their high specific strength, high specific modulus, excellent ductility, anticorrosion, heat-insulation, sound-insulation, shock absorption and high&low temperature resistance. They are used for radomes, inlets, airfoils(fuel tank included), flap, aileron, vertical tail, horizontal tail, air brake, skin, baseboards and tails, etc. Its hardness is up to 62~65HRC. The holes are greatly affected by the fibre laminates direction of carbon fibre reinforced composite material due to its anisotropy when drilling in unidirectional laminates. There are burrs, splits at the exit because of stress concentration. Besides there is delamination and the hole is prone to be smaller. Burrs are caused by poor sharpness of cutting edge, delamination, tearing, splitting are caused by the great stress caused by high thrust force. Poorer sharpness of cutting edge leads to lower cutting performance and higher drilling force at the same time. The present research focuses on the interrelation between rotation speed, feed, drill's geometry, drill life, cutting mode, tools material etc. and thrust force. At the same time, holes quantity and holes making difficulty of composites have also increased. It requires high performance drills which won't bring out defects and have long tool life. It has become a trend to develop super hard material tools and tools with special geometry for drilling

  15. A Study on Mechanical Properties of CNT-Reinforced Carbon/Carbon Composites

    Directory of Open Access Journals (Sweden)

    Yi-Luen Li

    2012-01-01

    Full Text Available Carbon/carbon composites (C/C composites possess superior characteristics of low density, high strength, extremely low coefficient of thermal expansion, and high fatigue resistance. In carbonization process, the high-temperature pyrolysis made of carbon, hydrogen, oxygen, and other elements results in a lot of voids and cavities generated in the interior of C/C composites. Therefore, the C/C composites are densified to fill the voids by using repeated impregnation. But densification is a time-wasting and complex process, which increases production costs in the manufacturing process. In this study, the multiwall carbon nanotubes (MWNTs were adopted as a reinforcement material for C/C composites to reduce the existence of voids or cavities and enhance the mechanical properties of C/C composites. According to the experimental results, the CNT-added C/C composite containing 1.2 wt% CNT possesses the greatest flexure strength, flexure modulus, and interlaminar shearing strength. Plus, the above-mentioned strength and modulus are increased by 23%, 19.2%, and 30%, respectively.

  16. Composite, nanostructured, super-hydrophobic material

    Science.gov (United States)

    D'Urso, Brian R.; Simpson, John T.

    2007-08-21

    A hydrophobic disordered composite material having a protrusive surface feature includes a recessive phase and a protrusive phase, the recessive phase having a higher susceptibility to a preselected etchant than the protrusive phase, the composite material having an etched surface wherein the protrusive phase protrudes from the surface to form a protrusive surface feature, the protrusive feature being hydrophobic.

  17. Composite Dielectric Materials for Electrical Switching

    Energy Technology Data Exchange (ETDEWEB)

    Modine, F.A.

    1999-04-25

    Composites that consist of a dielectric host containing a particulate conductor as a second phase are of interest for electrical switching applications. Such composites are "smart" materials that can function as either voltage or current limiters, and the difference in fimction depends largely upon whether the dielectric is filled to below or above the percolation threshold. It also is possible to combine current and voltage limiting in a single composite to make a "super-smart" material.

  18. Friction material composites copper-metal-free material design perspective

    CERN Document Server

    Sundarkrishnaa, K L

    2015-01-01

    This book examines material composites used in connection with brake friction, their design and safety. To aid in understanding, the essentials of friction are explained. This second edition was extended to include friction material composites without copper, as they offer an environmentally friendlier option. The second edition is intended to support beginners by offering insights into the essentials of friction material composites, helping them to develop a broader understanding of brake friction materials. Friction materials find wide-ranging applications in household and industrial appliances, brake pads for automotive applications, rail brake friction pads and composition brake blocks. This second edition is an introductory volume to a set of related books, and is based on the author’s experience and expertise with various material manufacturers, brake manufacturers, vehicle manufacturers, researchers and testing labs around the world with which the author has been associated for the past 28 years.

  19. X-ray microtomography, ultrasound and thermography for the characterization of defects in fiberglass and carbon fiber composite materials and elements; Roentgen-Mikrotomografie, Ultraschall und Thermographie fuer die Charakterisierung von Defekten in GFK- und CFK-Verbundwerkstoffen und -Elementen

    Energy Technology Data Exchange (ETDEWEB)

    Brunner, Andreas J.; Jerjen, Iwan; Plamondon, Mathieu; Furrer, Roman; Neuenschwander, Juerg [EMPA Eidgenoessische Materialpruefungs- und Forschungsanstalt, Duebendorf (Switzerland)

    2015-07-01

    Glass and carbon fiber reinforced plastics (GRP or CFRP composites) may have different defects that arise on the one hand in the manufacturing process and on the other hand occur or propagate under quasi-static or oscillating mechanical load. The characterization of the nature, location and size of defects is important among other things for optimization of manufacturing processes, modeling of material or component behavior and for the estimation of the useful life of components or structures from GFK or CFK composites. The contribution shows selected examples of the application of X-ray microtomography, ultrasound and thermography for the characterization of defects in fiberglass or carbon fiber composite components. In ''thick'' laminates and complex shapes the X-ray method is particularly suitable. [German] Glas- und Kohlenstoff-faserverstaerkte Kunststoffe (GFK- bzw. CFK-Verbundwerkstoffe) koennen unterschiedliche Defekte ausweisen, die einerseits im Herstellungsprozess entstehen und sich andererseits bei der Nutzung unter quasistatischer oder schwingender mechanischer Belastung ausbilden oder sich ausbreiten. Die Charakterisierung der Art, der Lage und der Groesse der Defekte ist u.a. fuer Optimierung der Herstellungsprozesse, Modellierung des Werkstoff- oder Bauteilverhaltens sowie der Abschaetzung der Nutzungsdauer von Komponenten oder Strukturen aus GFK- oder CFK-Verbundwerkstoffen wichtig. Der Beitrag zeigt ausgewaehlte Beispiele der Anwendung von Roentgen-Mikrotomografie, Ultraschall und Thermographie zur Charakterisierung von Defekten in GFK- oder CFK-Verbundwerkstoff-Bauteilen. Bei ''dicken'' Laminaten und komplexen Geometrien ist das Roentgenverfahren besonders geeignet.

  20. Composites and blends from biobased materials

    Energy Technology Data Exchange (ETDEWEB)

    Kelley, S.S. [National Renewable Energy Laboratory, Golden, CO (United States)

    1995-05-01

    The program is focused on the development of composites and blends from biobased materials to use as membranes, high value plastics, and lightweight composites. Biobased materials include: cellulose derivative microporous materials, cellulose derivative copolymers, and cellulose derivative blends. This year`s research focused on developing an improved understanding of the molecular features that cellulose based materials with improved properties for gas separation applications. Novel cellulose ester membrane composites have been developed and are being evaluated under a collaborative research agreement with Dow Chemicals Company.

  1. The behavior of delaminations in composite materials - experimental results

    Science.gov (United States)

    Chermoshentseva, A. S.; Pokrovskiy, A. M.; Bokhoeva, L. A.

    2016-02-01

    Delamination is one of the most common failure modes of composite materials. It may occur as a consequence of imperfections in the production process or the effects of external factors during the operational life of the composite laminates, such as the impact by foreign objects. This paper presents the results of mechanical tests and the optimum degrees of filling the composite materials (CM) with hydrophobic powder (Tarkosil T-20) depending on the latter mass concentration. The results present test samples of the CM with the underlying interlayer defects. The samples were fabricated of twenty-ply pre-preg (fiberglass or carbon fiber). The industrial grade glass is T-25 (VM) specification 6-11-380-76. The composite materials have nanosized additives in structure. The volume concentration of nanopowders is varying from 0.1% to 0.5%. This kind of research has been done for the first time.

  2. On the machinability of composite materials

    Energy Technology Data Exchange (ETDEWEB)

    Caprino, G.; De Iorio, I.; Santo, L.; Nele, L. [Univ. of Naples Federico II, Naples (Italy)

    1996-12-31

    Orthogonal cutting tests were carried out on a unidirectional Carbon Fibre Reinforced Plastic (CFRP), a unidirectional Glass Fibre Reinforced Plastic (GFRP), and a Sheet Moulding Compound (SMC) R50, using high speed steel tools. The force data were interpreted in the light of the usual force scheme adopted in metal cutting, disregarding the forces developing at the tool flank. It was found that, similarly to metals, the unit cutting force depends on the depth of cut t, decreasing with increasing the latter (size effect). The same trend was followed by the coefficient of friction. A new force scheme, previously proposed for composites, together with a different definition of {open_quotes}specific energy{close_quotes}, was then applied. Irrespective of the material considered, the new model results in a coefficient of friction independent of the cutting parameters, and in a specific energy X unaffected by the depth of cut. Nevertheless, X strongly decreases with increasing the rake angle, following different trends for CFRP and GFRP. Amongst the materials tested, the poorest machinability pertains to SMC.

  3. Application of radiation-crosslinked polytetrafluoroethylene to fiber-reinforced composite materials

    Energy Technology Data Exchange (ETDEWEB)

    Oshima, Akihiro E-mail: aks@taka.jaeri.go.jp; Udagawa, Akira; Morita, Yousuke

    2001-07-01

    Plain-woven carbon fiber-filled polytetrafluoroethylene (PTFE) composites were fabricated by radiation-crosslinking under selective conditions. High mechanical and frictional properties are found in the composite materials compared with crosslinked PTFE without fiber. The composite materials with optional shapes, which are laminated after electron beam (EB) crosslinking treatment of each mono-layer could also be fabricated. (author)

  4. Distribution of Triangle-shape Carbon Fibers in Composite Materials%三角形截面碳纤维在复合材料中的分布规律

    Institute of Scientific and Technical Information of China (English)

    刘新; 武湛君; 王荣国; 刘文博; 严佳

    2013-01-01

    三角形截面碳纤维在复合材料内部的排布结构像微波暗室一样,能够对入射的电磁波进行多次反射,从而衰减电磁波,使三角形截面碳纤维复合材料具有吸波性能,因此,研究三角形截面碳纤维在复合材料中的排布规律对研究其吸波机理非常重要.采用实验和模拟的方法对三角形截面碳纤维在复合材料中的排布规律进行了分析.首先,通过扫描电子显微镜(SEM)观察了多组三角形截面碳纤维复合材料试样的截面微观形貌,分析了三角形碳纤维在复合材料中的排布角度及均匀性;其次,为进一步研究三角形截面碳纤维复合材料的吸波机理,根据蒙特卡洛原理,通过Matlab软件对三角形截面碳纤维在复合材料中的排布情况进行了模拟.实验及数值模拟结果吻合较好,均表明三角形截面碳纤维在复合材料中的排布是以各种排布角度随机排布的,而三角形碳纤维分布是比较均匀的,没有明显的密布区域和稀疏区域,该模拟方法可以用于模拟不同含量的三角形截面碳纤维在复合材料中的排布规律.%The triangle cross-section carbon fiber reinforced plastics could be used as absorbing composite materials, in which the incident microwave can be reflected many times to be greatly attenuated. The microwave absorbing property is affected significantly by the distribution of the triangle cross-section carbon fibers in the composite materials. In this study, the distribution of the triangle cross-section carbon fibers in the triangle cross -section carbon fiber reinforced plastics is investigated by experimental and theoretical simulations. In order to study the angle arrangement and the homogeneity of the carbon fibers in the composite materials, the cross -section morphology of the samples is observed by the SEM. And a process based on the Monte Carlo Method is established to simulate the distribution of the triangle cross-section carbon

  5. Mechanical Properties of Self-Lubricating Carbon Fiber Knitted Fabric Composite Materials%碳纤维针织物自润滑复合材料力学性能研究

    Institute of Scientific and Technical Information of China (English)

    张强; 张鹏; 孙友松; 程永奇

    2015-01-01

    The effects of vacuum treatment and double reinforce by short fiber on the me-chanical properties of carbon fiber plain cloth or carbon fiber knitting fabric composite materials were studied.The results show that their compression strength increase by 8.86% and 8.08%and the impact strength increase by 15.55% and 9.43% through vacuum treatment respective-ly.Double reinforce by short fiber has significant influence on the compressive strength and pro-mote the compressive strength of carbon fiber plain cloth and carbon fiber knitting fabric by 9. 91% and 22.52%respectively,but the impact strength decreases slightly.%研究了真空处理和短切纤维二次增强对碳纤维平纹布和碳纤维针织物复合材料力学性能的影响。结果表明:真空处理前后其压缩强度分别提高了8.86%和8.08%,冲击强度则分别提高了15.55%和9.43%;短切纤维二次增强效果明显,压缩强度分别提高了9.91%和22.52%,但冲击强度略有下降。

  6. Synthesizing Smart Polymeric and Composite Materials

    OpenAIRE

    2013-01-01

    Smart materials have been widely investigated to explore new functionalities unavailable to traditional materials or to mimic the multifunctionality of biological systems. Synthetic polymers are particularly attractive as they already possess some of the attributes required for smart materials, and there are vast room to further enhance the existing properties or impart new properties by polymer synthesis or composite formulation. In this work, three types of smart polymer and composites have...

  7. Composite Materials for Low-Temperature Applications

    Science.gov (United States)

    2008-01-01

    Composite materials with improved thermal conductivity and good mechanical strength properties should allow for the design and construction of more thermally efficient components (such as pipes and valves) for use in fluid-processing systems. These materials should have wide application in any number of systems, including ground support equipment (GSE), lunar systems, and flight hardware that need reduced heat transfer. Researchers from the Polymer Science and Technology Laboratory and the Cryogenics Laboratory at Kennedy Space Center were able to develop a new series of composite materials that can meet NASA's needs for lightweight materials/composites for use in fluid systems and also expand the plastic-additive markets. With respect to thermal conductivity and physical properties, these materials are excellent alternatives to prior composite materials and can be used in the aerospace, automotive, military, electronics, food-packaging, and textile markets. One specific application of the polymeric composition is for use in tanks, pipes, valves, structural supports, and components for hot or cold fluid-processing systems where heat flow through materials is a problem to be avoided. These materials can also substitute for metals in cryogenic and other low-temperature applications. These organic/inorganic polymeric composite materials were invented with significant reduction in heat transfer properties. Decreases of 20 to 50 percent in thermal conductivity versus that of the unmodified polymer matrix were measured. These novel composite materials also maintain mechanical properties of the unmodified polymer matrix. These composite materials consist of an inorganic additive combined with a thermoplastic polymer material. The intrinsic, low thermal conductivity of the additive is imparted into the thermoplastic, resulting in a significant reduction in heat transfer over that of the base polymer itself, yet maintaining most of the polymer's original properties. Normal

  8. Multifunctional composites using reinforced laminae with carbon-nanotube forests

    Science.gov (United States)

    Veedu, Vinod P.; Cao, Anyuan; Li, Xuesong; Ma, Kougen; Soldano, Caterina; Kar, Swastik; Ajayan, Pulickel M.; Ghasemi-Nejhad, Mehrdad N.

    2006-06-01

    Traditional fibre-reinforced composite materials with excellent in-plane properties fare poorly when out-of-plane through-thickness properties are important. Composite architectures with fibres designed orthogonal to the two-dimensional (2D) layout in traditional composites could alleviate this weakness in the transverse direction, but all of the efforts so far have only produced limited success. Here, we unveil an approach to the 3D composite challenge, without altering the 2D stack design, on the basis of the concept of interlaminar carbon-nanotube forests that would provide enhanced multifunctional properties along the thickness direction. The carbon-nanotube forests allow the fastening of adjacent plies in the 3D composite. We grow multiwalled carbon nanotubes on the surface of micro-fibre fabric cloth layouts, normal to the fibre lengths, resulting in a 3D effect between plies under loading. These nanotube-coated fabric cloths serve as building blocks for the multilayered 3D composites, with the nanotube forests providing much-needed interlaminar strength and toughness under various loading conditions. For the fabricated 3D composites with nanotube forests, we demonstrate remarkable improvements in the interlaminar fracture toughness, hardness, delamination resistance, in-plane mechanical properties, damping, thermoelastic behaviour, and thermal and electrical conductivities making these structures truly multifunctional.

  9. New generation fiber reinforced polymer composites incorporating carbon nanotubes

    Science.gov (United States)

    Soliman, Eslam

    The last five decades observed an increasing use of fiber reinforced polymer (FRP) composites as alternative construction materials for aerospace and infrastructure. The high specific strength of FRP attracted its use as non-corrosive reinforcement. However, FRP materials were characterized with a relatively low ductility and low shear strength compared with steel reinforcement. On the other hand, carbon nanotubes (CNTs) have been introduced in the last decade as a material with minimal defect that is capable of increasing the mechanical properties of polymer matrices. This dissertation reports experimental investigations on the use of multi-walled carbon nanotubes (MWCNTs) to produce a new generation of FRP composites. The experiments showed significant improvements in the flexure properties of the nanocomposite when functionalized MWCNTs were used. In addition, MWCNTs were used to produce FRP composites in order to examine static, dynamic, and creep behavior. The MWCNTs improved the off-axis tension, off-axis flexure, FRP lap shear joint responses. In addition, they reduced the creep of FRP-concrete interface, enhanced the fracture toughness, and altered the impact resistance significantly. In general, the MWCNTs are found to affect the behaviour of the FRP composites when matrix failure dominates the behaviour. The improvement in the mechanical response with the addition of low contents of MWCNTs would benefit many industrial and military applications such as strengthening structures using FRP composites, composite pipelines, aircrafts, and armoured vehicles.

  10. LDRD final report on carbon nanotube composites

    Energy Technology Data Exchange (ETDEWEB)

    Cahill, P.A.; Rand, P.B.

    1997-04-01

    Carbon nanotubes and their composites were examined using computational and experimental techniques in order to modify the mechanical and electrical properties of resins. Single walled nanotubes were the focus of the first year effort; however, sufficient quantities of high purity single walled nanotubes could not be obtained for mechanical property investigations. The unusually high electrical conductivity of composites loaded with <1% of multiwalled nanotubes is useful, and is the focus of continuing, externally funded, research.

  11. Materials research at Stanford University. [composite materials, crystal structure, acoustics

    Science.gov (United States)

    1975-01-01

    Research activity related to the science of materials is described. The following areas are included: elastic and thermal properties of composite materials, acoustic waves and devices, amorphous materials, crystal structure, synthesis of metal-metal bonds, interactions of solids with solutions, electrochemistry, fatigue damage, superconductivity and molecular physics and phase transition kinetics.

  12. Design and Fabrication of E-Glass /carbon/graphite epoxy hybrid composite leaf spring

    Science.gov (United States)

    Gopalakrishnan, T.; Raja, M.; Jothi Prakash, V. M.; Gnanavel, C.

    2017-03-01

    The Automobile Industry has shown increase interest for replacement of steel leaf spring with that of composite leaf spring. Substituting composite materials for conventional metallic materials has many advantages because of higher specific stiffness, strength and fatigue resistance etc. This work deals with the replacement of conventional steel leaf spring with a hybrid Composite leaf spring using E -Glass/Carbon/Graphite/Epoxy. The hybrid composite is obtained by introducing more than one fiber in the reinforcement phase. The hybrid composite is fabricated by the vacuum bag technique. The result shows that introduction of carbon and graphite fiber in the reinforcement phase increases the stiffness of the composite.

  13. Iron-carbon composites for the remediation of chlorinated hydrocarbons

    Science.gov (United States)

    Sunkara, Bhanu Kiran

    This research is focused on engineering submicron spherical carbon particles as effective carriers/supports for nanoscale zerovalent iron (NZVI) particles to address the in situ remediation of soil and groundwater chlorinated contaminants. Chlorinated hydrocarbons such as trichloroethylene (TCE) and tetrachloroethylene (PCE) form a class of dense non-aqueous phase liquid (DNAPL) toxic contaminants in soil and groundwater. The in situ injection of NZVI particles to reduce DNAPLs is a potentially simple, cost-effective, and environmentally benign technology that has become a preferred method in the remediation of these compounds. However, unsupported NZVI particles exhibit ferromagnetism leading to particle aggregation and loss in mobility through the subsurface. This work demonstrates two approaches to prepare carbon supported NZVI (iron-carbon composites) particles. The objective is to establish these iron-carbon composites as extremely useful materials for the environmental remediation of chlorinated hydrocarbons and suitable materials for the in situ injection technology. This research also demonstrates that it is possible to vary the placement of iron nanoparticles either on the external surface or within the interior of carbon microspheres using a one-step aerosol-based process. The simple process of modifying iron placement has significant potential applications in heterogeneous catalysis as both the iron and carbon are widely used catalysts and catalyst supports. Furthermore, the aerosol-based process is applied to prepare new class of supported catalytic materials such as carbon-supported palladium nanoparticles for ex situ remediation of contaminated water. The iron-carbon composites developed in this research have multiple functionalities (a) they are reactive and function effectively in reductive dehalogenation (b) they are highly adsorptive thereby bringing the chlorinated compound to the proximity of the reactive sites and also serving as adsorption

  14. High value carbon materials from PET recycling

    Science.gov (United States)

    Parra, J. B.; Ania, C. O.; Arenillas, A.; Rubiera, F.; Pis, J. J.

    2004-11-01

    Poly(ethylene) terephthalate (PET), has become one of the major post-consumer plastic waste. In this work special attention was paid to minimising PET residues and to obtain a high value carbon material. Pyrolysis and subsequent activation of PET from post-consumer soft-drink bottles was performed. Activation was carried out at 925 °C under CO2 atmosphere to different burn-off degrees. Textural characterisation of the samples was carried out by performing N2 adsorption isotherms at -196 °C. The obtained carbons materials were mainly microporous, presenting low meso and macroporosity, and apparent BET surface areas of upto 2500 m2 g-1. The capacity of these materials for phenol adsorption and PAHs removal from aqueous solutions was measured and compared with that attained with commercial active carbons. Preliminary tests also showed high hydrogen uptake values, as good as the results obtained with high-tech carbon materials.

  15. Yeast-based microporous carbon materials for carbon dioxide capture.

    Science.gov (United States)

    Shen, Wenzhong; He, Yue; Zhang, Shouchun; Li, Junfen; Fan, Weibin

    2012-07-01

    A hierarchical microporous carbon material with a Brunauer-Emmett-Teller surface area of 1348 m(2) g(-1) and a pore volume of 0.67 cm(3) g(-1) was prepared from yeast through chemical activation with potassium hydroxide. This type of material contains large numbers of nitrogen-containing groups (nitrogen content >5.3 wt%), and, consequently, basic sites. As a result, this material shows a faster adsorption rate and a higher adsorption capacity of CO(2) than the material obtained by directly carbonizing yeast under the same conditions. The difference is more pronounced in the presence of N(2) or H(2)O, showing that chemical activation of discarded yeast with potassium hydroxide could afford high-performance microporous carbon materials for the capture of CO(2).

  16. Biomedical composites materials, manufacturing and engineering

    CERN Document Server

    Davim, J Paulo

    2013-01-01

    Composite materials are engineered materials, made from two or more constituents with significantly different physical or chemical properties which remain separate on a macroscopic level within the finished structure. Due to their special mechanical and physical properties they have the potential to replace conventional materials in various fields such as the biomedical industry.

  17. Use of composite materials in oil industry

    OpenAIRE

    Trifunović, Prvoslav

    2011-01-01

    The most frequently used composites for fabrication of primary and secondary constructions within the oil industry are made of epoxy, phenolic or polymer matrix combined with glass, carbon or aramid fibers. For fabrication of risers, thermoplastic polymers (polyethylene, polyvinyldenefluoride, and polyamide) are used, which are to be wound around steel reinforcement of riser. Polymer may be reinforced with glass or carbon fibers. Instead of thermoplastic polymers, epoxy matrix reinforced with...

  18. Rapid Fabrication of Carbide Matrix/Carbon Fiber Composites

    Science.gov (United States)

    Williams, Brian E.; Bernander, Robert E.

    2007-01-01

    Composites of zirconium carbide matrix material reinforced with carbon fibers can be fabricated relatively rapidly in a process that includes a melt infiltration step. Heretofore, these and other ceramic matrix composites have been made in a chemical vapor infiltration (CVI) process that takes months. The finished products of the CVI process are highly porous and cannot withstand temperatures above 3,000 F (approx.1,600 C). In contrast, the melt-infiltration-based process takes only a few days, and the composite products are more nearly fully dense and have withstood temperatures as high as 4,350 F (approx.2,400 C) in a highly oxidizing thrust chamber environment. Moreover, because the melt- infiltration-based process takes much less time, the finished products are expected to cost much less. Fabrication begins with the preparation of a carbon fiber preform that, typically, is of the size and shape of a part to be fabricated. By use of low-temperature ultraviolet-enhanced chemical vapor deposition, the carbon fibers in the preform are coated with one or more interfacial material(s), which could include oxides. The interfacial material helps to protect the fibers against chemical attack during the remainder of the fabrication process and against oxidation during subsequent use; it also enables slippage between the fibers and the matrix material, thereby helping to deflect cracks and distribute loads. Once the fibers have been coated with the interfacial material, the fiber preform is further infiltrated with a controlled amount of additional carbon, which serves as a reactant for the formation of the carbide matrix material. The next step is melt infiltration. The preform is exposed to molten zirconium, which wicks into the preform, drawn by capillary action. The molten metal fills most of the interstices of the preform and reacts with the added carbon to form the zirconium carbide matrix material. The zirconium does not react with the underlying fibers because they

  19. NARloy-Z-Carbon Nanotube Composites

    Science.gov (United States)

    Bhat, Biliyar N.

    2012-01-01

    Motivation: (1) NARloy-Z (Cu-3%Ag-0.5%Zr) is the state of the art, high thermal conductivity structural alloy used for making liquid rocket engine main combustion chamber liner. It has a Thermal conductivity approx 80% of pure copper. (2) Improving the thermal conductivity of NARloy-Z will help to improve the heat transfer efficiency of combustion chamber. (3)Will also help to reduce the propulsion system mass and increase performance. It will also increases thrust to weight ratio. (4) Improving heat transfer helps to design and build better thermal management systems for nuclear propulsion and other applications. Can Carbon nanotubes (CNT) help to improve the thermal conductivity (TC)of NARloy-Z? (1)CNT's have TC of approx 20X that of copper (2) 5vol% CNT could potentially double the TC of NARloy-Z if properly aligned (3) Improvement will be less if CNT s are randomly distributed, provided there is a good thermal bond between CNT and matrix. Prior research has shown poor results (1) No TC improvement in the copper-CNT composite reported (2)Reported values are typically lower (3) Attributed to high contact thermal resistance between CNT and Cu matrix (4)Results suggest that a bonding material between CNT and copper matrix is required to lower the contact thermal resistance It is hypothesized that Zr in NARloy-Z could act as a bonding agent to lower the contact thermal resistance between CNT and matrix.

  20. Thick-walled carbon composite multifunctional structures

    Science.gov (United States)

    Haake, John M.; Jacobs, Jack H.; McIlroy, Bruce E.

    1997-06-01

    Satellite programs are moving in the direction of smaller and lighter structures. Technological advances have permitted more sophisticated equipment to be consolidated into compact spaces. Micro-satellites, between 10 and 100 kg, will incorporate micro-electric devices into the lay-up of the satellite structure. These structures will be designed to carry load, provide thermal control, enhance damping, and include integrated passive electronics. These multifunctional structures offer lighter weight, reduced volume, and a 'smarter' overall package for incorporation of sensors, electronics, fiber optics, powered appendages or active components. McDonnell Douglas Corporation (MDC) has applied technology from the synthesis and processing of intelligent cost effective structures (SPICES) and independent research and development (IRAD) programs to the modular instrument support system (MISS) for multifunctional space structures and micro-satellites. The SPICES program was funded by the Defense Advanced Research Projects Agency (DARPA) to develop affordable manufacturing processes for smart materials to be used in vibration control, and the MISS program was funded by NASA-Langley. The MISS program was conceived to develop concepts and techniques to make connections between different multifunctional structures. MDA fabricated a trapezoidal carbon composite structure out of IM7/977-3 tape prepreg. Flex circuits, thermal and optical conduits were embedded to realize a utility modular connector. These provide electrical, thermal, optical and mechanical connections between micro- satellite components. A quick disconnect mount was also developed to accommodate a variety of devices such as solar arrays, power sources, thermal transfer and vibration control modules.

  1. Carbon nanotube-based functional materials for optical limiting.

    Science.gov (United States)

    Chen, Yu; Lin, Ying; Liu, Ying; Doyle, James; He, Nan; Zhuang, Xiaodong; Bai, Jinrui; Blau, Werner J

    2007-01-01

    Optical limiting is an important application of nonlinear optics, useful for the protection of human eyes, optical elements, and optical sensors from intense laser pulses. An optical limiter is such a device that strongly attenuates high intensity light and potentially damaging light such as focused laser beams, whilst allowing for the high transmission of ambient light. Optical limiting properties of carbon nanotube suspensions, solubilized carbon nanotubes, small molecules doped carbon nanotubes and polymer/carbon nanotube composites have been reviewed. The optical limiting responses of carbon nanotube suspensions are shown to be dominated by nonlinear scattering as a result of thermally induced solvent-bubble formation and sublimation of the nanotubes, while the solubilized carbon nanotubes optically limit through nonlinear absorption mechanism and exhibit significant solution-concentration-dependent optical limiting responses. In the former case the optical limiting results are independent of nanotube concentrations at the same linear transmittance as that of the solubilized systems. Many efforts have been invested into the research of polymer/carbon nanotube composites in an attempt to allow for the fabrication of films required for the use of nanotubes in a real optical limiting application. The higher carbon nanotube content samples block the incident light more effectively at higher incident energy densities or intensities. The optical limiting mechanism of these composite materials is quite complicated. Besides nonlinear scattering contribution to the optical limiting, there may also be other contributions e.g., nonlinear absorption, nonlinear refraction, electronic absorption and others to the optical limiting. Further improvements in the optical limiting efficiency of the composites and in the dispersion and alignment properties of carbon nanotubes in the polymer matrix could be realized by variation of both nanostructured guest and polymer host, and by

  2. Ceramic composites: Enabling aerospace materials

    Science.gov (United States)

    Levine, S. R.

    1992-01-01

    Ceramics and ceramic matrix composites (CMC) have the potential for significant impact on the performance of aerospace propulsion and power systems. In this paper, the potential benefits are discussed in broad qualitative terms and are illustrated by some specific application case studies. The key issues in need of resolution for the potential of ceramics to be realized are discussed.

  3. Synthesis of Carbon Nanotube (CNT Composite Membranes

    Directory of Open Access Journals (Sweden)

    Dusan Losic

    2010-12-01

    Full Text Available Carbon nanotubes are attractive approach for designing of new membranes for advanced molecular separation because of their unique transport properties and ability to mimic biological protein channels. In this work the synthetic approach for fabrication of carbon nanotubes (CNTs composite membranes is presented. The method is based on growth of multi walled carbon nanotubes (MWCNT using chemical vapour deposition (CVD on the template of nanoporous alumina (PA membranes. The influence of experimental conditions including carbon precursor, temperature, deposition time, and PA template on CNT growth process and quality of fabricated membranes was investigated. The synthesis of CNT/PA composites with controllable nanotube dimensions such as diameters (30–150 nm, and thickness (5–100 µm, was demonstrated. The chemical composition and morphological characteristics of fabricated CNT/PA composite membranes were investigated by various characterisation techniques including scanning electron microscopy (SEM, energy-dispersive x-ray spectroscopy (EDXS, high resolution transmission electron microscopy (HRTEM and x-ray diffraction (XRD. Transport properties of prepared membranes were explored by diffusion of dye (Rose Bengal used as model of hydrophilic transport molecule.

  4. In Situ Formation of Carbon Nanomaterials on Bulk Metallic Materials

    Directory of Open Access Journals (Sweden)

    J. Y. Xu

    2014-01-01

    Full Text Available Carbon nanomaterials were synthesized in situ on bulk 316L stainless steel, pure cobalt, and pure nickel by hybrid surface mechanical attrition treatment (SMAT. The microstructures of the treated samples and the resulted carbon nanomaterials were investigated by SEM and TEM characterizations. Different substrates resulted in different morphologies of products. The diameter of carbon nanomaterials is related to the size of the nanograins on the surface layer of substrates. The possible growth mechanism was discussed. Effects of the main parameters of the synthesis, including the carbon source and gas reactant composition, hydrogen, and the reaction temperature, were studied. Using hybrid SMAT is proved to be an effective way to synthesize carbon nanomaterials in situ on surfaces of metallic materials.

  5. Carbon fibre composite for ventilation air methane (VAM) capture

    Energy Technology Data Exchange (ETDEWEB)

    Thiruvenkatachari, Ramesh [Commonwealth Scientific and Industrial Research Organisation (CSIRO), PO Box 883, Kenmore, Queensland 4069 (Australia); Su Shi, E-mail: Shi.Su@csiro.au [Commonwealth Scientific and Industrial Research Organisation (CSIRO), PO Box 883, Kenmore, Queensland 4069 (Australia); Yu Xinxiang [Commonwealth Scientific and Industrial Research Organisation (CSIRO), PO Box 883, Kenmore, Queensland 4069 (Australia)

    2009-12-30

    Coal mine methane (CMM) is not only a hazardous greenhouse gas but is also a wasted energy resource, if not utilised. This paper evaluates a novel adsorbent material developed for capturing methane from ventilation air methane (VAM) gas in underground coal mines. The adsorbent material is a honeycomb monolithic carbon fibre composite (HMCFC) consisting of multiple parallel flow-through channels and the material exhibits unique features including low pressure drop, good mechanical properties, ability to handle dust-containing gas streams, good thermal and electrical conductivity and selective adsorption of gases. During this study, a series of HMCFC adsorbents (using different types of carbon fibres) were successfully fabricated. Experimental data demonstrated the proof-of-concept of using the HMCFC adsorbent to capture methane from VAM gas. The adsorption capacity of the HMCFC adsorbent was twice that of commercial activated carbon. Methane concentration of 0.56% in the inlet VAM gas stream is reduced to about 0.011% after it passes through the novel carbon fibre composite adsorbent material at ambient temperature and atmospheric pressure. This amounts to a maximum capture efficiency of 98%. These encouraging laboratory scale studies have prompted further large scale trials and economic assessment.

  6. Carbon fibre composite for ventilation air methane (VAM) capture.

    Science.gov (United States)

    Thiruvenkatachari, Ramesh; Su, Shi; Yu, Xin Xiang

    2009-12-30

    Coal mine methane (CMM) is not only a hazardous greenhouse gas but is also a wasted energy resource, if not utilised. This paper evaluates a novel adsorbent material developed for capturing methane from ventilation air methane (VAM) gas in underground coal mines. The adsorbent material is a honeycomb monolithic carbon fibre composite (HMCFC) consisting of multiple parallel flow-through channels and the material exhibits unique features including low pressure drop, good mechanical properties, ability to handle dust-containing gas streams, good thermal and electrical conductivity and selective adsorption of gases. During this study, a series of HMCFC adsorbents (using different types of carbon fibres) were successfully fabricated. Experimental data demonstrated the proof-of-concept of using the HMCFC adsorbent to capture methane from VAM gas. The adsorption capacity of the HMCFC adsorbent was twice that of commercial activated carbon. Methane concentration of 0.56% in the inlet VAM gas stream is reduced to about 0.011% after it passes through the novel carbon fibre composite adsorbent material at ambient temperature and atmospheric pressure. This amounts to a maximum capture efficiency of 98%. These encouraging laboratory scale studies have prompted further large scale trials and economic assessment.

  7. Preparation of composite electroheat carbon film

    Institute of Scientific and Technical Information of China (English)

    XIA Jin-tong; TU Chuan-jun; LI Yan; HU Li-min; DENG Jiu-hua

    2005-01-01

    A kind of conductive and heating unit, which can reach a high surface electroheat temperature at a low voltage, was developed in view of the traditional electroheat coating which has a low surface electroheat temperature and an insufficient heat resistance of its binder. The coating molded electroheat carbon film(CMECF) was prepared by carbonizing the coating which was prepared by adding modified resin into flake graphite and carbon fiber, coating molded onto the surface of the heat resisting matrix after dried, while the hot pressing molded electroheat thick carbon film(HPMETCF) was prepared by carbonizing the bodies whose powders were hot pressing molded directly.The surface and inner microstructure of the carbon film was characterized and analyzed by SEM and DSC/TG, while electroheat property was tested by voltage-current volume resistivity tester and electrical parameter tester. The results show that, close-packed carbon network configuration is formed within the composite electroheat carbon film film after anti-oxidizable treatment reaches a higher surface electroheat temperature than that of the existing electroheat coatings at a low voltage, and has excellent electroheat property, high thermal efficiency as well as stable physicochemical property. It is found that, at room temperature(19± 2 ℃) and 22 V for 5 min, the surface electroheat temperature of the self-produced CMECF (mfiller/mresin = 1. 8/1) reaches 112 ℃ while HPMETCF (mfiller/mresin = 3. 6/1) reaches 265 ℃.

  8. Fibrous and textile materials for composite applications

    CERN Document Server

    Fangueiro, Raul

    2016-01-01

    This book focuses on the fibers and textiles used in composite materials. It presents both existing technologies currently used in commercial applications and the latest advanced research and developments. It also discusses the different fiber forms and architectures, such as short fibers, unidirectional tows, directionally oriented structures or advanced 2D- and 3D-textile structures that are used in composite materials. In addition, it examines various synthetic, natural and metallic fibers that are used to reinforce polymeric, cementitious and metallic matrices, as well as fiber properties, special functionalities, manufacturing processes, and composite processing and properties. Two entire chapters are dedicated to advanced nanofiber and nanotube reinforced composite materials. The book goes on to highlight different surface treatments and finishes that are applied to improve fiber/matrix interfaces and other essential composite properties. Although a great deal of information about fibers and textile str...

  9. Mesoporous Carbon-based Materials for Alternative Energy Applications

    Science.gov (United States)

    Cross, Kimberly Michelle

    Increasing concerns for the escalating issues activated by the effect of carbon dioxide emissions on the global climate from extensive use of fossil fuels and the limited amount of fossil resources has led to an in-depth search for alternative energy systems, primarily based on nuclear or renewable energy sources. Recent innovations in the production of more efficient devices for energy harvesting, storage, and conversion are based on the incorporation of nanostructured materials into electrochemical systems. The aforementioned nano-electrochemical energy systems hold particular promise for alternative energy transportation related technologies including fuel cells, hydrogen storage, and electrochemical supercapacitors. In each of these devices, nanostructured materials can be used to increase the surface area where the critical chemical reactions occur within the same volume and mass, thereby increasing the energy density, power density, electrical efficiency, and physical robustness of the system. Durable corrosion resistant carbon support materials for fuel cells have been designed by adding conductive low cost carbon materials with chemically robust ceramic materials. Since a strict control of the pore size is mandatory to optimize properties for improved performance, chemical activation agents have been utilized as porogens to tune surface areas, pore size distributions, and composition of carbon-based mesoporous materials. Through the use of evaporative self-assembly methods, both randomly disordered and surfactant-templated, ordered carbon-silica nanocomposites have been synthesized with controlled surface area, pore volume, and pore size ranging from 50-800 m2/g, 0.025-0.75 cm3/g, and 2-10 nm, respectively. Multi-walled carbon nanotubes (MWNTs) ranging from 0.05-1.0 wt. % were added to the aforementioned carbon-silica nanocomposites, which provided an additional increase in surface area and improved conductivity. Initially, a conductivity value of 0.0667 S

  10. CO2 capture in different carbon materials.

    Science.gov (United States)

    Jiménez, Vicente; Ramírez-Lucas, Ana; Díaz, José Antonio; Sánchez, Paula; Romero, Amaya

    2012-07-03

    In this work, the CO(2) capture capacity of different types of carbon nanofibers (platelet, fishbone, and ribbon) and amorphous carbon have been measured at 26 °C as at different pressures. The results showed that the more graphitic carbon materials adsorbed less CO(2) than more amorphous materials. Then, the aim was to improve the CO(2) adsorption capacity of the carbon materials by increasing the porosity during the chemical activation process. After chemical activation process, the amorphous carbon and platelet CNFs increased the CO(2) adsorption capacity 1.6 times, whereas fishbone and ribbon CNFs increased their CO(2) adsorption capacity 1.1 and 8.2 times, respectively. This increase of CO(2) adsorption capacity after chemical activation was due to an increase of BET surface area and pore volume in all carbon materials. Finally, the CO(2) adsorption isotherms showed that activated amorphous carbon exhibited the best CO(2) capture capacity with 72.0 wt % of CO(2) at 26 °C and 8 bar.

  11. Fabrication of aluminum matrix composite reinforced with carbon nanotubes

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    1.0 wt.% carbon nanotube (CNT) reinforced 2024A1 matrix composite was fabricated by cold isostatic press and subsequent hot extrusion techniques. The mechanical properties of the composite were measured by a tensile test. Meanwhile, the fracture surfaces were examined using field emission scanning electron microscopy. The experimental results show that CNTs are dispersed homogeneously in the composite and that the interfaces of the Al matrix and the CNT bond well. Although the tensile strength and the Young's modulus of the composite are enhanced markedly, the elongation does not decrease when compared with the matrix material fabricated under the same process. The reasons for the increments may be the extraordinary mechanical properties of CNTs, and the bridging and pulling-out role of CNTs in the Al matrix composite.

  12. Fracture morphology of carbon fiber reinforced plastic composite laminates

    Directory of Open Access Journals (Sweden)

    Vinod Srinivasa

    2010-09-01

    Full Text Available Carbon fiber reinforced plastic (CFRP composites have been extensively used in fabrication of primary structures for aerospace, automobile and other engineering applications. With continuous and widespread use of these composites in several advanced technology, the frequency of failures is likely to increase. Therefore, to establish the reasons for failures, the fracture modes should be understood thoroughly and unambiguously. In this paper, CFRP composite have been tested in tension, compression and flexural loadings; and microscopic study with the aid of Scanning Electron Microscope (SEM has been performed on failed (fractured composite surfaces to identify the principle features of failure. Efforts have been made in correlating the fracture surface characteristics to the failure mode. The micro-mechanics analysis of failure serves as a useful guide in selecting constituent materials and designing composites from the failure behavior point of view. Also, the local failure initiation results obtained here has been reliably extended to global failure prediction.

  13. Carbon fiber composite molecular sieves

    Energy Technology Data Exchange (ETDEWEB)

    Burchell, T.D.; Rogers, M.R. [Oak Ridge National Lab., TN (United States)

    1997-12-01

    Monolithic adsorbents based on isotropic pitch fibers have been developed jointly by ORNL and the University of Kentucky, Center for Applied Energy Research. The monoliths are attractive for gas separation and storage applications because of their unique combination of physical properties and microporous structure. Currently at ORNL the monoliths are produced in billets that are 10 cm in diameter and 25 cm in length. The monolithic adsorbent material is being considered for guard bed applications on a natural gas (NG) powered device. In order for the material to be successful in this application, one must attain a uniform activation to modest micropore volumes throughout the large monoliths currently being produced. Here the authors report the results of a study directed toward attaining uniform activation in these billets.

  14. Behavior of pure and modified carbon/carbon composites in atomic oxygen environment

    Institute of Scientific and Technical Information of China (English)

    Xiao-chong Liu; Lai-fei Cheng; Li-tong Zhang; Xin-gang Luan; Hui Mei

    2014-01-01

    Atomic oxygen (AO) is considered the most erosive particle to spacecraft materials in low earth orbit (LEO). Carbon fiber, car-bon/carbon (C/C), and some modified C/C composites were exposed to a simulated AO environment to investigate their behaviors in LEO. Scanning electron microscopy (SEM), AO erosion rate calculation, and mechanical property testing were used to characterize the material properties. Results show that the carbon fiber and C/C specimens undergo significant degradation under the AO bombing. According to the effects of AO on C/C-SiC and CVD-SiC-coated C/C, a condensed CVD-SiC coat is a feasible approach to protect C/C composites from AO degradation.

  15. Advanced materials based on carbon nanotube arrays, yarns and papers

    Science.gov (United States)

    Bradford, Phlip David

    Carbon nanotubes have hundreds of potential applications but require innovative processing techniques to manipulate the microscopic carbon dust into useful devices and products. This thesis describes efforts to process carbon nanotubes (CNTs) using novel methods with the goals of: (1) improving the properties of energy absorbing and composite carbon nanotube materials and (2) increasing understanding of fundamental structure-property relationships within these materials. Millimeter long CNTs, in the form of arrays, yarns and papers, were used to produce energy absorbing foams and high volume fraction CNT composites. Vertically aligned CNT arrays were grown on silicon substrates using chemical vapor deposition (CVD) of ethylene gas over iron nano-particles. The low density, millimeter thick arrays were tested under compression as energy absorbing foams. With additional CVD processing steps, it was possible to tune the compressive properties of the arrays. After the longest treatment, the compressive strength of the arrays was increased by a factor of 35 with a density increase of only six fold, while also imparting recovery from compression to the array. Microscopy revealed that the post-synthesis CVD treatment increased the number of CNT walls through an epitaxial type radial growth on the surface of the as-grown tubes. The increase in tube radius and mutual support between nanotubes explained the increases in compressive strength while an increase in nanotube roughness was proposed as the morphological change responsible for recovery in the array. Carbon nanotube yarns were used as the raw material for macroscopic textile preforms with a multi-level hierarchical carbon nanotube (CNT) structure: nanotubes, bundles, spun single yarns, plied yarns and 3-D braids. In prior tensile tests, composites produced from the 3-D braids exhibited unusual mechanical behavior effects. The proposed physical hypotheses explained those effects by molecular level interactions and

  16. Cumulative Damage Model for Advanced Composite Materials.

    Science.gov (United States)

    1982-07-01

    ultimately used an exponential in the present example for added simplicity) and we norma - lize the function so that it becomes the modifier that determines...Testing and Design (Second Conference), ASTM STP 497, ASTM (1972) pp. 170-188. 5. Halpin, J. C., et al., "Characterization of Composites for the...Graphite Epoxy Composites," Proc. Symposium on Composite Materials: Testing and Design, ASTM , (Ma’rch 20, 1978) New Orleans, LA. 18. Hashin, Z. and Rotem

  17. Multiphysicsbased Condition Monitoring of Composite Materials

    OpenAIRE

    Xue, Hui; Sharma, Puneet; Khawaja, Hassan Abbas

    2015-01-01

    Composites are increasingly being used in products such as: automobiles, bridges, boats, drillships, offshore platforms, aircrafts and satellites. The increased usage of these composite materials and the fact that the conditions pertaining to their failure are not fully understood makes it imperative to develop condition monitoring systems for composite structures. In this work, we present a theoretical framework for the development of a condition monitoring system. For this, we plan...

  18. Cupric Hexacyanoferrate Nanoparticle Modified Carbon Ceramic Composite Electrodes

    Institute of Scientific and Technical Information of China (English)

    WANG,Peng(王鹏); ZHU,Guo-Yi(朱果逸)

    2002-01-01

    Graphite powder-supported cupric hexacyanoferrate (CuHCF)nanoparticles were dispersed into methyltrimethoxysilane-based gels to produce a conducting carbon ceramic composite, which was used as electrode material to fabricate surface-renewable CuHCF-modified electrodes. Electrochemical behavior of the CuHCF-modified carbon ceramic composite electrodes was characterized using cyclic and square-wave voitammetry.Cyclic voltammograms at various scan rates indicated that peak currents were surface-confined at low scan rates. In the presence of glutathione, a clear electrocatalytic response was observed at the CuHCF-modified composite electrodes. In addition, the electrodes exhibited a distinct advantage of reproducible surface-renewal by simple mechanical polishing on emery paper, as well as ease of preparation, and good chemical and mechanical stability in a flowing stream.

  19. Cupric Hexacyanoferrate Nanoparticle Modified Carbon Ceramic Composite Electrodes

    Institute of Scientific and Technical Information of China (English)

    WANG,Peng; ZHU,Guo-Yi

    2002-01-01

    Graphite powder-supported cupric hexacyanoferrate(CuHCF) nanoparticles were dispersed into methyltrimethoxysilane-based gels to produce a conducting carbon ceramic composite,which was used as electrode materials to fabricate surface-renewable CuHCF-modified electrodes.Electrochemical behavior of the CuHCF-modified carbon ceramic composite electrodes was characterized using cyclic and square-wave voltammetry. Cyclinc voltammograms at various scan rates indicated that peak currents were suface-confined at low scan rates.In the presence of glutathione,a clear electrocatalytic response was observed at the CuHCF-modified composite electrodes.In addition,the electrodes exhibited a distinct advantage of reproducible surface-renewal by simple mechanical polishing on emery paper,as well as ease of preparation,and good chemical and mechanical stability in a flowing stream.

  20. Graphitic Carbon Materials Tailored for the Rapid Adsorption of Biomolecules

    Science.gov (United States)

    Pescatore, Nicholas A.

    Sepsis is an overactive inflammatory response to an infection, with 19 million cases estimated worldwide and causing organ dysfunction if left untreated. Three pro-inflammatory cytokines are seen from literature review as vital biomarkers for sepsis and are interleukin-6 (IL-6), interleukin-8 (IL-8) and tumor necrosis factor-alpha (TNF-alpha), which have the potential to be removed by hemoperfusion. This thesis examines carbon nanomaterials for their adsorption capabilities in the search for an optimal material for blood cleansing hemoperfusion application, such as mediating the effects of sepsis. Non-porous and porous carbon polymorphs and their properties are investigated in this thesis for their protein adsorption capabilities. Polymer-derived mesoporous carbons were compared to non-porous graphene nanoplatelets (GNP's) to observe changes in adsorption capacity for cytokines between porous and non-porous materials. GNP's were functionalized via high temperature vacuum annealing, air oxidation, acid oxidation and amination treatments to understand the effect of surface chemistry on adsorption. For practical use in a hemoperfusion column, polymer-derived carbon beads and composite materials such as cryogel and PTFE-GNP composites were designed and tested for their adsorption capacity. At concentrations of IL-6, IL-8, and TNF-alpha seen in septic patients, these cytokines were completely removed from the blood after 5 minutes of incubation with GNP's. Overall, a low-cost, scalable carbon adsorbent was found to provide a novel approach of rapidly removing pro-inflammatory cytokines from septic patients.

  1. Thermal conductivity, electrical conductivity and specific heat of copper-carbon fiber composite

    Science.gov (United States)

    Kuniya, Keiichi; Arakawa, Hideo; Kanai, Tsuneyuki; Chiba, Akio

    1988-01-01

    A new material of copper/carbon fiber composite is developed which retains the properties of copper, i.e., its excellent electrical and thermal conductivity, and the property of carbon, i.e., a small thermal expansion coefficient. These properties of the composite are adjustable within a certain range by changing the volume and/or the orientation of the carbon fibers. The effects of carbon fiber volume and arrangement changes on the thermal and electrical conductivity, and specific heat of the composite are studied. Results obtained are as follows: the thermal and electrical conductivity of the composite decrease as the volume of the carbon fiber increases, and were influenced by the fiber orientation. The results are predictable from a careful application of the rule of mixtures for composites. The specific heat of the composite was dependent, not on fiber orientation, but on fiber volume. In the thermal fatigue tests, no degradation in the electrical conductivity of this composite was observed.

  2. Effective Behavior of Composite Materials.

    Science.gov (United States)

    2014-09-26

    7AD-A158 941 EFFECTIVE BEHAVIOR OF COMPOSITE MTERIRLS(A) NEW YORK i/i UNIV MY COURANT INST OF ATHEMATICAL SCIENCES 6CPAPANICOLAOU 23 APR 85 5274192... Courant ilfapphcabt e Instit.te of Math. Sciences AF0SR/NM 6c. ADDRESS Cit). State and ZIP Code, 7b. ADDRESS (City. State and ZIP Code) 251 Mercer St Bldg...Papanicolaou Courant Institute 251 Mercer Street New York, N.Y. 10012 i~istr~utlo2 During this period two thesis ipja b&have completed ’their work and have

  3. Novel Nanosized Adsorbing Composite Cathode Materials for the Next Generational Lithium Battery

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yong; ZHENG Wei; ZHANG Ping; WANG Lizhen; XIA Tongchi; HU Xinguo; YU Zhenxing

    2007-01-01

    A novel carbon-sulfur nano-composite material was synthesized by heating sublimed sulfur and high surface area activated carbon (HSAAC) under certain conditions. The physical and chemical performances of the novel carbon-sulfur nano-composite were characterized by scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET) and X-ray diffraction (XRD). The electrochemical performances of nano-composite were characterized by charge-discharge characteristic, cyclic voltammetry and electrochemical impendence spectroscopy (EIS). The experimental results indicate that the electrochemical capability of nanocomposite material was superior to that of traditional S-containing composite material. The cathode made by carbon-sulfur nano-composite material shows a good cycle ability and a high specific charge-discharge capacity. The HSAAC shows a vital role in adsorbing sublimed sulfur and the polysulfides within the cathode and is an excellent electric conductor for a sulfur cathode and prevents the shuttle behavior of the lithium-sulfur battery.

  4. Drilling Damage in Composite Material

    Directory of Open Access Journals (Sweden)

    Luís Miguel P. Durão

    2014-05-01

    Full Text Available The characteristics of carbon fibre reinforced laminates have widened their use from aerospace to domestic appliances, and new possibilities for their usage emerge almost daily. In many of the possible applications, the laminates need to be drilled for assembly purposes. It is known that a drilling process that reduces the drill thrust force can decrease the risk of delamination. In this work, damage assessment methods based on data extracted from radiographic images are compared and correlated with mechanical test results—bearing test and delamination onset test—and analytical models. The results demonstrate the importance of an adequate selection of drilling tools and machining parameters to extend the life cycle of these laminates as a consequence of enhanced reliability.

  5. Synthesis, characterization and application of functional carbon nano materials

    Science.gov (United States)

    Chu, Jin

    The synthesis, characterizations and applications of carbon nanomaterials, including carbon nanorods, carbon nanosheets, carbon nanohoneycombs and carbon nanotubes were demonstrated. Different growth techniques such as pulsed laser deposition, DC/RF sputtering, hot filament physical vapour deposition, evaporative casting and vacuum filtration methods were introduced or applied for synthesizing carbon nanomaterials. The morphology, chemical compositions, bond structures, electronic, mechanical and sensing properties of the obtained samples were investigated. Tilted well-aligned carbon micro- and nano- hybrid rods were fabricated on Si at different substrate temperatures and incident angles of carbon source beam using the hot filament physical vapour deposition technique. The morphologic surfaces and bond structures of the oblique carbon rod-like structures were investigated by scanning electron microscopy, field emission scanning electron microscopy, transmission electron diffraction and Raman scattering spectroscopy. The field emission behaviour of the fabricated samples was also tested. Carbon nanosheets and nanohoneycombs were also synthesized on Si substrates using a hot filament physical vapor deposition technique under methane ambient and vacuum, respectively. The four-point Au electrodes are then sputtered on the surface of the nanostructured carbon films to form prototypical humidity sensors. The sensing properties of prototypical sensors at different temperature, humidity, direct current, and alternative current voltage were characterized. Linear sensing response of sensors to relative humidity ranging from 11% to 95% is observed at room temperature. Experimental data indicate that the carbon nanosheets based sensors exhibit an excellent reversible behavior and long-term stability. It also has higher response than that of the humidity sensor with carbon nanohoneycombs materials. Conducting composite films containing carbon nanotubes (CNTs) were prepared in

  6. Deposition of amorphous carbon-silver composites

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Zarco, O. [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Circuito Exterior s/n, Ciudad Universitaria. 04510, Mexico D. F. Mexico (Mexico); Rodil, S.E., E-mail: ser42@iim.unam.m [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Circuito Exterior s/n, Ciudad Universitaria. 04510, Mexico D. F. Mexico (Mexico); Camacho-Lopez, M.A. [Facultad de Quimica, Universidad Autonoma del Estado de Mexico, Tollocan s/n, esq. Paseo Colon, Toluca, Estado de Mexico, 50110 (Mexico)

    2009-12-31

    Composites of amorphous carbon films and silver were deposited by co-sputtering, where the target (10 cm diameter) was of pure graphite with small inclusion of pure silver (less than 1 cm{sup 2}). The films were deposited under different powers, from 40 to 250 W, and different target-substrate distances. The substrate was earthed and rotated in order to obtain a uniform distribution of the silver content. The addition of the Ag piece into the target increased the deposition rate of the carbon films, which could be related to the higher sputter yield of the silver, but there seems to be also a contribution from a larger emission of secondary electrons from the Ag that enhances the plasma and therefore the sputtering process becomes more efficient. Scanning electron micrographs acquired using backscattered electrons showed that the silver was segregated from the carbon matrix, forming nanoparticles or larger clusters as the power was increased. The X-ray diffraction pattern showed that the silver was crystalline and the carbon matrix remained amorphous, although for certain conditions a peak attributed to fullerene-like structures was obtained. Finally, we used Raman spectroscopy to understand the bonding characteristics of the carbon-silver composites, finding that there are variations in the D/G ratio, which can be correlated to the observed structure and X-ray diffraction results.

  7. Characteristics of carbon and hydrogen isotopic compositions of light hydrocarbons

    Institute of Scientific and Technical Information of China (English)

    沈平

    1995-01-01

    Light hydrocarbons named in the present paper refer to the natural gas-associated light oil and condensate 46 light oil and condensate samples from 11 oil-bearing basins of China were collected and their carbon and hydrogen isotopic compositions were analysed in terms of their total hydrocarbons, saturated hydrocarbons and a part of aromatic fractions, and gas-source materials and their sedimentary environments were discussed based on the above-mentioned data and the geological background of each area. From the view of carbon and hydrogen isotopic composition of total hydrocarbons and saturated hydrocarbons, it is revealed that the condensate related to coal-bearing strata is enriched in 13C and D while that related to the source material of type I-II is enriched in 12C. In general, the isotopic composition of carbon is mainly attributed to the inheriting effect of their source materials, whereas that of hydrogen principally reflects the correlationship between hydrogen isotopes and the sedimentary envi

  8. Center for Cement Composite Materials

    Science.gov (United States)

    1990-01-31

    pastes have shown that the matrix is microporous; mesopores are absent unless the material is allowed to dry out. This results in water adsorption at low...only to water. When subsequently dried a portion of3 the porosity is converted to larger mesopores . • Only about one third of the cement reacts in a...Frictional sliding, in this case was characterized by a decreasing slope in the loading curve followed by hysteresis in the unload/reloading curves

  9. Breakthroughs in Mesoporous Composite Materials

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Mesoporous materials have attracted a great deal of attention due to their extremely high surface area, uniform and tunable pore structure (2-50nm in diameter), and have been investigated extensively since its invention. Unfortunately,their catalytic properties are far away from the expectation due to their amorphous and inert framework and poor stability. This research project is aimed at the design and synthesis of mesoporous-

  10. Modification of carbon fiber / epoxy matrix interphase in a composite material : Design of a self-healing interphase by introducing thermally reversible Diels-Alder adducts

    OpenAIRE

    2014-01-01

    A thermally self-healable carbon/epoxy interphase was designed based on Diels-Alder (D-A) thermally reversible covalent bonds. The D-A modified interphase was formed between maleimide groups grafted on carbon fiber surface and furan groups introduced into epoxy network. The self-healing ability was characterized by a micromechanical approach using the micro-droplet debonding test. In this work, carbon fiber surface underwent a three-step treatment to graft maleimide groups, including HNO3 oxi...

  11. RADIATION EFFECTS ON EPOXY CARBON FIBER COMPOSITE

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, E

    2008-05-30

    Carbon fiber-reinforced bisphenol-A epoxy matrix composite was evaluated for gamma radiation resistance. The composite was exposed to total gamma doses of 50, 100, and 200 Mrad. Irradiated and baseline samples were tested for tensile strength, hardness and evaluated using FTIR (Fourier transform infrared) spectroscopy and DSC (differential scanning calorimetry) for structural changes. Scanning electron microscopy was used to evaluate microstructural behavior. Mechanical testing of the composite bars revealed no apparent change in modulus, strain to failure, or fracture strength after exposures. However, testing of only the epoxy matrix revealed changes in hardness, thermal properties, and FTIR results with increasing gamma irradiation. The results suggest the epoxy within the composite can be affected by exposure to gamma irradiation.

  12. Multifunctional Laminated Composite Materials for Protective Clothing

    Directory of Open Access Journals (Sweden)

    Nermin M. Aly

    2014-10-01

    Full Text Available Protective clothing performs a vital role in maintaining the safety of human in workplace. The developments in this field are proceeding to fulfill the needs with multifunctional materials at competitive costs. Recently, the protective clothing field introduces the usage of composite materials taking advantage of their outstanding properties. In this paper, the multifunctional performance of hybrid laminated composites (HLC was investigated aiming to be utilized in protective clothing. The influences of reinforcement and resin properties on the physical properties of the laminated composites and their resistance to puncture load and UV transmittance were studied. ANOVA test was used for the statistical analysis of the results. The results showed that, the reinforcement material and structure and the fiber/matrix interface have major influences on the laminated composites performance. It was revealed that, the HLC fabricated from (polyester/glass fabric with satin 4 structure and nonwoven glass fiber mat exhibited the best functional performance.

  13. Indirect composite resin materials for posterior applications.

    Science.gov (United States)

    Shellard, E; Duke, E S

    1999-12-01

    Indirect composite resin restorations were introduced a number of years ago as possible alternatives to traditional metallic or ceramic-based indirect restorations. However, the earlier formulations did not provide evidence of improvement in mechanical and physical properties over chairside-placed direct composite resin materials. Because they required more tooth structure removal than direct restorations, their use became unpopular and was abandoned by most clinicians. Over the past few years, a new class of composite resin indirect materials has surfaced in the profession. Various technologies have been suggested as reinforcement mechanisms. Fibers, matrix modifications, and an assortment of innovations have been proposed for enhancing indirect composite resin restorations. Applications are from inlay restorations all the way to multi-unit fixed prostheses. This manuscript summarizes some of the progress made in this area. When available, data is presented to provide clinicians with guidelines and indications for the use of these materials.

  14. A decade of science and engineering of composite materials at the North West Composites Centre, University of Manchester, UK

    Science.gov (United States)

    Soutis, Constantinos

    2016-12-01

    The University of Manchester, School of Materials has a large multidisciplinary research programme on polymers, composites and carbon-based materials. This takes place through fundamental studies of structure-property relationships for these materials, including controlled synthesis and processing, and effects of structure andnano-, meso- and macro-scale morphology on physical properties and engineering applications.

  15. A decade of science and engineering of composite materials at the North West Composites Centre, University of Manchester, UK

    Science.gov (United States)

    Soutis, Constantinos

    2017-04-01

    The University of Manchester, School of Materials has a large multidisciplinary research programme on polymers, composites and carbon-based materials. This takes place through fundamental studies of structure-property relationships for these materials, including controlled synthesis and processing, and effects of structure andnano-, meso- and macro-scale morphology on physical properties and engineering applications.

  16. Oxidation Kinetics and Strength Degradation of Carbon Fibers in a Cracked Ceramic Matrix Composite

    Science.gov (United States)

    Halbig, Michael C.

    2003-01-01

    Experimental results and oxidation modeling will be presented to discuss carbon fiber susceptibility to oxidation, the oxidation kinetics regimes and composite strength degradation and failure due to oxidation. Thermogravimetric Analysis (TGA) was used to study the oxidation rates of carbon fiber and of a pyro-carbon interphase. The analysis was used to separately obtain activation energies for the carbon constituents within a C/SiC composite. TGA was also conducted on C/SiC composite material to study carbon oxidation and crack closure as a function of temperature. In order to more closely match applications conditions C/SiC tensile coupons were also tested under stressed oxidation conditions. The stressed oxidation tests show that C/SiC is much more susceptible to oxidation when the material is under an applied load where the cracks are open and allow for oxygen ingress. The results help correlate carbon oxidation with composite strength reduction and failure.

  17. FIBROUS CERAMIC-CERAMIC COMPOSITE MATERIALS PROCESSING AND PROPERTIES

    OpenAIRE

    1986-01-01

    The introduction of continuous fibers in a ceramic matrix can improve its toughness, if the fiber-matrix bonding is weak enough, due to matrix microcracking and fiber pull-out. Ceramic-ceramic composite materials are processed according to liquid or gas phase techniques. The most important are made of glass, carbide, nitride or oxide matrices reinforced with carbon, SiC or Al2O3 fibers.

  18. Surface modifications of carbon nanotubes and their application to composite materials%碳纳米管表面改性及其应用于复合材料的研究现状

    Institute of Scientific and Technical Information of China (English)

    孟胜皓; 闫军; 汪明球; 杜仕国; 王琦

    2014-01-01

    Surface modification of CNTs can improve their surface activity,dispersion ability,and the compatibility between CNTs and base matrix,resulting in reinforcement of composite material. The methods of surface modification of CNTs are classified into physical methods and chemical methods. The physical methods consist of high-energy mechanical polishing method,high-energy ball milling method,and ultrasonic vibration method. The chemical methods consist of acid treatment method, method of coupling agent,electroless plating method,high-energy rays irradiation method,and atom transfer radical polymerization. In practical application,several modification methods can be used in combination to make the performance more stable and achieve more diverse properties. Meanwhile,the applications of modified carbon nanotubes to various composite materials are reviewed. Two focal points in modification of carbon nanotubes are proposed:one is to keep structural integrity of carbon nanotube itself,the second is to improve the dispersion of carbon nanotubes in the matrix.%对碳纳米管进行表面改性可提高碳纳米管的表面活性、分散能力和与基体材料之间的相容性,从而提高其在复合材料中的增强效果。本文介绍了碳纳米管表面改性的方法,分为物理法和化学法,物理法主要有高能机械研磨法、高能球磨法和超声振动法;化学法主要有酸处理法、偶联剂法、化学镀法、高能射线辐照法和原子转移自由基聚合法。在实际应用中常将几种改性方法联合使用,使得到的改性产物性能更稳定,性质更多样化。同时,介绍了改性后的碳纳米管在各种复合材料中的应用现状。并指出了对碳纳米管进行改性的两个重点:一是尽量保持碳纳米管的本身结构完整性;二是提高碳纳米管在基体中的分散性。

  19. Empirical Formula for the Relationship between Compressive Strength and Test Temperature of Carbon/Polyimide Composites

    OpenAIRE

    濱口, 泰正; Hamaguchi, Yasumasa

    2002-01-01

    T800H/PMR-15 carbon/polyimide composite possesses good specific strength and specific rigidity in the high-temperature region around 300C. This material is an advanced structural composite for use in elevons and other secondary structures of the unmanned space reentry vehicle HOPE-X. The author carried out basic strength evaluation tests on this material. Compressive strength data is especially important for structural design using composite materials. Compressive strength data was therefore ...

  20. Modeling Lightning Impact Thermo-Mechanical Damage on Composite Materials

    Science.gov (United States)

    Muñoz, Raúl; Delgado, Sofía; González, Carlos; López-Romano, Bernardo; Wang, De-Yi; LLorca, Javier

    2014-02-01

    Carbon fiber-reinforced polymers, used in primary structures for aircraft due to an excellent strength-to-weight ratio when compared with conventional aluminium alloy counterparts, may nowadays be considered as mature structural materials. Their use has been extended in recent decades, with several aircraft manufacturers delivering fuselages entirely manufactured with carbon composites and using advanced processing technologies. However, one of the main drawbacks of using such composites entails their poor electrical conductivity when compared with aluminium alloy competitors that leads to lightning strikes being considered a significant threat during the service life of the aircraft. Traditionally, this problem was overcome with the use of a protective copper/bronze mesh that added additional weight and reduced the effectiveness of use of the material. Moreover, this traditional sizing method is based on vast experimental campaigns carried out by subjecting composite panels to simulated lightning strike events. While this method has proven its validity, and is necessary for certification of the structure, it may be optimized with the aid provided by physically based numerical models. This paper presents a model based on the finite element method that includes the sources of damage observed in a lightning strike, such as thermal damage caused by Joule overheating and electromagnetic/acoustic pressures induced by the arc around the attachment points. The results of the model are compared with lightning strike experiments carried out in a carbon woven composite.

  1. Growth of Carbon Nanostructure Materials Using Laser Vaporization

    Science.gov (United States)

    Zhu, Shen; Su, Ching-Hua; Lehozeky, S.

    2000-01-01

    Since the potential applications of carbon nanotubes (CNT) was discovered in many fields, such as non-structure electronics, lightweight composite structure, and drug delivery, CNT has been grown by many techniques in which high yield single wall CNT has been produced by physical processes including arc vaporization and laser vaporization. In this presentation, the growth mechanism of the carbon nanostructure materials by laser vaporization is to be discussed. Carbon nanoparticles and nanotubes have been synthesized using pulsed laser vaporization on Si substrates in various temperatures and pressures. Two kinds of targets were used to grow the nanostructure materials. One was a pure graphite target and the other one contained Ni and Co catalysts. The growth temperatures were 600-1000 C and the pressures varied from several torr to 500 torr. Carbon nanoparticles were observed when a graphite target was used, although catalysts were deposited on substrates before growing carbon films. When the target contains catalysts, carbon nanotubes (CNT) are obtained. The CNT were characterized by scanning electron microscopy, x-ray diffraction, optical absorption and transmission, and Raman spectroscopy. The temperature-and pressure-dependencies of carbon nanotubes' growth rate and size were investigated.

  2. Carbon fiber composite characterization in adverse thermal environments.

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Vasquez, Sylvia; Brown, Alexander L.; Hubbard, Joshua A.; Ramirez, Ciro J.; Dodd, Amanda B.

    2011-05-01

    The behavior of carbon fiber aircraft composites was studied in adverse thermal environments. The effects of resin composition and fiber orientation were measured in two test configurations: 102 by 127 millimeter (mm) test coupons were irradiated at approximately 22.5 kW/m{sup 2} to measure thermal response, and 102 by 254 mm test coupons were irradiated at approximately 30.7 kW/m{sup 2} to characterize piloted flame spread in the vertically upward direction. Carbon-fiber composite materials with epoxy and bismaleimide resins, and uni-directional and woven fiber orientations, were tested. Bismaleimide samples produced less smoke, and were more resistant to flame spread, as expected for high temperature thermoset resins with characteristically lower heat release rates. All materials lost approximately 20-25% of their mass regardless of resin type, fiber orientation, or test configuration. Woven fiber composites displayed localized smoke jetting whereas uni-directional composites developed cracks parallel to the fibers from which smoke and flames emanated. Swelling and delamination were observed with volumetric expansion on the order of 100% to 200%. The purpose of this work was to provide validation data for SNL's foundational thermal and combustion modeling capabilities.

  3. Electron spectroscopy of rubber and resin-based composites containing 2D carbon

    Energy Technology Data Exchange (ETDEWEB)

    Kaciulis, S., E-mail: saulius.kaciulis@ismn.cnr.it [Institute for the Study of Nanostructured Materials, ISMN-CNR, P.O. Box 10, Monterotondo Stazione, 00015 Roma (Italy); Mezzi, A.; Balijepalli, S.K. [Institute for the Study of Nanostructured Materials, ISMN-CNR, P.O. Box 10, Monterotondo Stazione, 00015 Roma (Italy); Lavorgna, M. [Institute of Polymers, Composites and Biomaterials, IPCB-CNR, P.le Fermi, 80055 Napoli (Italy); Xia, H.S. [State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, 610065 Sichuan (China)

    2015-04-30

    Composite materials with 2D carbon (graphene and/or single wall carbon nanotubes) are very promising due to their extraordinary electrical and mechanical properties. Graphene and natural rubber composites, which may be used for the gaskets or sealants, were prepared by ultrasonically assisted latex-mixing exfoliation and in-situ reduction process, with two vulcanization approaches: roll-mixing and hot-pressing. Also the resin-based composites, filled with micro-particles of Ag and graphene or carbon nanotubes, have been studied. The standards for the compositional characterization of these materials still are not established. In addition to the mostly used techniques, such as Raman spectroscopy and electron microscopy, also Auger electron spectroscopy can be employed for the identification of graphene. In this study, the shape of C KVV peak, excited by electron beam and X-ray photons, has been investigated in different composite materials containing graphene and carbon nanotubes. A spectroscopic method for 2D carbon recognition, based on the D{sub x} parameter which is determined from C KVV signal excited by X-ray photons, was proposed and verified. Even a small content of graphene in different types of composites was sufficient for this recognition due to the dominating presence of graphene on the surface of composites. - Highlights: • Chemical composition of the rubber composites was determined by XPS. • Auger spectrum of carbon was used for graphene identification in composites. • Small content of graphene was sufficient for its recognition from the D parameter.

  4. Development of a Novel, Reactive Extrusion Process for Continuous Production of Long, Pure Carbon Nanotubes for Application in Lightweight Composite Materials Project

    Data.gov (United States)

    National Aeronautics and Space Administration — According to the NASA A2-01 topic description titled Materials and Structures for Future Aircraft, "advanced materials and structures technologies are needed in all...

  5. Modeling of carbon nanotubes, graphene and their composites

    CERN Document Server

    Silvestre, Nuno

    2014-01-01

    This book contains ten chapters, authored by world experts in the field of simulation at nano-scale and aims to demonstrate the potentialities of computational techniques to model the mechanical behavior of nano-materials, such as carbon nanotubes, graphene and their composites. A large part of the research currently being conducted in the fields of materials science and engineering mechanics is devoted to carbon nanotubes, graphene and their applications. In this process, computational modeling is a very attractive research tool due to the difficulties in manufacturing and testing of nano-materials. Both atomistic modeling methods, such as molecular mechanics and molecular dynamics, and continuum modeling methods are being intensively used. Continuum modeling offers significant advantages over atomistic modeling such as the reduced computational effort, the capability of modeling complex structures and bridging different analysis scales, thus enabling modeling from the nano- to the macro-scale. On the oth...

  6. Carbon-fiber composite molecular sieves for gas separation

    Energy Technology Data Exchange (ETDEWEB)

    Jagtoyen, M.; Derbyshire, F. [Univ. of Kentucky, Lexington, KY (United States)

    1996-08-01

    This report describes continuing work on the activation and characterization of formed carbon fiber composites. The composites are produced at the Oak Ridge National Laboratory (ORNL) and activated at the Center for Applied Energy Research (CAER) using steam, CO{sub 2}, or O{sub 2} at different conditions of temperature and time, and with different furnace configurations. The general aims of the project are to produce uniformly activated samples with controlled pore structures for specialist applications such as gas separation and water treatment. In previous work the authors reported that composites produced from isotropic pitch fibers weighing up to 25g can be uniformly activated through the appropriate choice of reaction conditions and furnace configurations. They have now succeeded in uniformly activating composites of dimensions up to 12 x 7 x 6 cm, or up to about 166 gram - a scale-up factor of about six. Part of the work has involved the installation of a new furnace that can accommodate larger composites. Efforts were made to achieve uniform activation in both steam and CO{sub 2}. The authors have also succeeded in producing materials with very uniform and narrow pore size distributions by using a novel method involving low temperature oxygen chemisorption in combination with heat treatment in N{sub 2} at high temperatures. Work has also started on the activation of PAN based carbon fibers and fiber composites with the aim of producing composites with wide pore structures for use as catalyst supports. So far activation of the PAN fiber composites supplied by ORNL has been difficult which is attributed to the low reactivity of the PAN fibers. As a result, studies are now being made of the activation of the PAN fibers to investigate the optimum carbonization and activation conditions for PAN based fibers.

  7. Fabrication of Carbon Nanotube - Chromium Carbide Composite Through Laser Sintering

    Science.gov (United States)

    Liu, Ze; Gao, Yibo; Liang, Fei; Wu, Benxin; Gou, Jihua; Detrois, Martin; Tin, Sammy; Yin, Ming; Nash, Philip; Tang, Xiaoduan; Wang, Xinwei

    2016-03-01

    Ceramics often have high hardness and strength, and good wear and corrosion resistance, and hence have many important applications, which, however, are often limited by their poor fracture toughness. Carbon nanotubes (CNTs) may enhance ceramic fracture toughness, but hot pressing (which is one typical approach of fabricating CNT-ceramic composites) is difficult to apply for applications that require localized heat input, such as fabricating composites as surface coatings. Laser beam may realize localized material sintering with little thermal effect on the surrounding regions. However, for the typical ceramics for hard coating applications (as listed in Ref.[1]), previous work on laser sintering of CNT-ceramic composites with mechanical property characterizations has been very limited. In this paper, research work has been reported on the fabrication and characterization of CNT-ceramic composites through laser sintering of mixtures of CNTs and chromium carbide powders. Under the studied conditions, it has been found that laser-sintered composites have a much higher hardness than that for plasma-sprayed composites reported in the literature. It has also been found that the composites obtained by laser sintering of CNTs and chromium carbide powder mixtures have a fracture toughness that is ~23 % higher than the material obtained by laser sintering of chromium carbide powders without CNTs.

  8. Structural changes during pitch-based carbon granular composites carbonisation

    Energy Technology Data Exchange (ETDEWEB)

    Mendez, A.; Santamaria, R.; Granda, M.; Menendez, R. [CSIC, Oviedo (Spain)

    2008-02-15

    This article deals with the study of carbon composites behavior during their carbonization. Composites were prepared using four granular carbons (graphite, anthracite, green petroleum coke, and foundry coke) and four pitches (a commercial impregnating coal-tar pitch, an air-blown and two thermally treated pitches). The evolution of the optical microstructure, porosity, volume, and weight of carbon composites was monitored at different intermediate carbonization temperatures (350, 500, 700, and finally 1000{sup o}C). The porosity of composites increases with carbonization due to volume changes and weight loss of pitches. Weight loss of carbon composites during their carbonization mainly depends on the pitch characteristics and it was slightly influenced by the presence of granular carbon. On the other hand, carbon composites with the commercial coal-tar pitch and foundry coke, anthracite, or graphite deform in the initial stages of carbonization (<350{sup o}C) probably due to the lower porosity of the green pellets and the high amount of low-molecular weight compounds of the pitch. Carbon composites with green petroleum coke underwent important dimensional changes during their carbonization, expanding initially and then shrinking at temperatures above 700{sup o}C. The type of granular carbon strongly influenced the microstructure of the final carbon composite, as a result of its effect on the development of mesophase. Graphite, anthracite and foundry coke delays mesophase development, whereas green petroleum coke accelerates mesophase formation.

  9. Processes for fabricating composite reinforced material

    Energy Technology Data Exchange (ETDEWEB)

    Seals, Roland D.; Ripley, Edward B.; Ludtka, Gerard M.

    2015-11-24

    A family of materials wherein nanostructures and/or nanotubes are incorporated into a multi-component material arrangement, such as a metallic or ceramic alloy or composite/aggregate, producing a new material or metallic/ceramic alloy. The new material has significantly increased strength, up to several thousands of times normal and perhaps substantially more, as well as significantly decreased weight. The new materials may be manufactured into a component where the nanostructure or nanostructure reinforcement is incorporated into the bulk and/or matrix material, or as a coating where the nanostructure or nanostructure reinforcement is incorporated into the coating or surface of a "normal" substrate material. The nanostructures are incorporated into the material structure either randomly or aligned, within grains, or along or across grain boundaries.

  10. Validation of the numerical model of single-layer composites reinforced with carbon fiber and aramid

    Science.gov (United States)

    Sava, Mihaela; Hadǎr, Anton; Pǎrǎuşanu, Ioan; Petrescu, Horia-Alexandru; Baciu, Florin; Marinel, Stǎnescu Marius

    2016-06-01

    In this work we studied the experimental validation of the model and finite element analysis for a single layer of composite materials reinforced with carbon (denoted as C), aramid (K) and carbon-aramid (C-K) fibers. In the literature there are not many details about the differences that arise between transversal and longitudinal characteristics of composite materials reinforced with fabric, compared to those with unidirectional fibers. In order to achieve carbon and aramid composites we used twill fabric and for carbon-aramid plain fabric, as shown in Figure 1. In order to observe the static behavior of the considered specimens, numerical simulations were carried out in addition to the experimental determination of the characteristics of these materials. Layered composites are obviously the most widespread formula for getting advanced composite structures. It allows a unique variety of material and structural combinations leading to optimal design in a wide range of applications [1,2]. To design and verify the material composites it is necessary to know the basic mechanical constants of the materials. Almost all the layered composites consider that the every layer is an orthotropic material, so there are nine independent constants of material corresponding to the three principal directions: Young modulus E1, E2 and E3, shear modulus G12, G23 and G13, and major poison ratios ν12, ν23, ν13. Experimental determinations were performed using traction tests and strain gauges. For each of the three above mentioned materials, five samples were manufactured.

  11. 碳纳米管/石墨烯杂化材料改性环氧树脂研究%Study on Epoxy Resin Composites Modiifed with Carbon Nanotubes/Graphene Hybrid Materials

    Institute of Scientific and Technical Information of China (English)

    吴俊青; 俞科静; 钱坤

    2015-01-01

    采用物理法和化学多步法合成了碳纳米管/石墨烯杂化材料,通过红外光谱表征证明杂化材料的成功合成,通过沉淀实验表明化学多步法合成的碳杂化材料具有良好的分散性和分散稳定性。将碳纳米杂化材料按照质量分数0.3%添加到环氧树脂(EP)中制备复合材料,对复合材料的拉伸强度和断裂韧性进行表征,并通过扫描电子显微镜对复合材料的断面进行表征。结果表明,碳纳米管/石墨烯杂化材料对EP的增强增韧效果较好,尤其是化学多步法合成的杂化材料改性EP复合材料,其拉伸强度最大,曲线积分面积最大,弹性模量最小,韧性最好。这可能要归因于化学多步法合成的杂化材料具有更为稳定的三维结构,可以更好地承担和转移外部载荷。%The successful preparation of hybrid materials through physical and multi-step methods were characterized by FTIR. The sedimentation tests proved that the hybrid materials(multi-step) had excellent dispersion and dispersion stability. The epoxy resin(EP) composites were prepared by adding 0.3%content of carbon nanomaterials into EP. The tensile strength and tensile toughness were tested by tensile experiment. And then the micromorphology of fracture surface of EP composites was characterized by scanning electron microscope. The results indicate that both hybrid materials have strengthening and toughness effect,especially EP composites with multi-step hybrid materials have the biggest tensile strength and tensile toughness with big integral area and smallest elasticity modulus. The reasons may be attributed to that the multi-step hybrid materials have more stable nanostructure to help EP to undertake and transfer more external load.

  12. Microwave Measurements of Ferrite Polymer Composite Materials

    Directory of Open Access Journals (Sweden)

    Rastislav Dosoudil

    2004-01-01

    Full Text Available The article focuses on the microwave measurements performed on the nickel-zinc sintered ferrite with the chemical formula Ni0.3Zn0.7Fe2O4 produced by the ceramic technique and composite materials based on this ferrite and a non-magnetic polymer (polyvinyl chloride matrix. The prepared composite samples had the same particle size distribution 0-250um but different ferrite particle concentrations between 23 vol% and 80 vol%. The apparatus for measurement of the signal proportional to the absolute value of scattering parameter S11 (reflexion coefficient is described and the dependence of measured reflected signal on a bias magnetic field has been studied. By means of experiments, the resonances to be connected with the geometry of microwave experimental set-up were distinguished from ferromagnetic resonance arising in ferrite particles of composite structure. The role of local interaction fields of ferrite particles in composite material has been discussed.

  13. On the Mechanical Behavior of Advanced Composite Material Structures

    Science.gov (United States)

    Vinson, Jack

    During the period between 1993 and 2004, the author, as well as some colleagues and graduate students, had the honor to be supported by the Office of Naval Research to conduct research in several aspects of the behavior of structures composed of composite materials. The topics involved in this research program were numerous, but all contributed to increasing the understanding of how various structures that are useful for marine applications behaved. More specifically, the research topics focused on the reaction of structures that were made of fiber reinforced polymer matrix composites when subjected to various loads and environmental conditions. This included the behavior of beam, plate/panel and shell structures. It involved studies that are applicable to fiberglass, graphite/carbon and Kevlar fibers imbedded in epoxy, polyester and other polymeric matrices. Unidirectional, cross-ply, angle ply, and woven composites were involved, both in laminated, monocoque as well as in sandwich constructions. Mid-plane symmetric as well as asymmetric laminates were studied, the latter involving bending-stretching coupling and other couplings that only can be achieved with advanced composite materials. The composite structures studied involved static loads, dynamic loading, shock loading as well as thermal and hygrothermal environments. One major consideration was determining the mechanical properties of composite materials subjected to high strain rates because the mechanical properties vary so significantly as the strain rate increases. A considerable number of references are cited for further reading and study for those interested.

  14. 78 FR 16044 - Hazardous Materials Packaging-Composite Cylinder Standards; Public Meeting

    Science.gov (United States)

    2013-03-13

    ... reinforced plastic (DOT-FRP) or fully wrapped carbon-fiber reinforced aluminum lined cylinders (DOT- CFFC... TRANSPORTATION Pipeline and Hazardous Materials Safety Administration Hazardous Materials Packaging--Composite... the manufacture, marking, sale and use of non-DOT specification composite cylinders. The...

  15. Carbon nanotube materials from hydrogen storage

    Energy Technology Data Exchange (ETDEWEB)

    Dillon, A.C.; Bekkedahl, T.A.; Cahill, A.F. [National Renewable Energy Laboratory, Golden, CO (United States)

    1995-09-01

    The lack of convenient and cost-effective hydrogen storage is a major impediment to wide scale use of hydrogen in the United States energy economy. Improvements in the energy densities of hydrogen storage systems, reductions in cost, and increased compatibility with available and forecasted systems are required before viable hydrogen energy use pathways can be established. Carbon-based hydrogen adsorption materials hold particular promise for meeting and exceeding the U.S. Department of Energy hydrogen storage energy density targets for transportation if concurrent increases in hydrogen storage capacity and carbon density can be achieved. These two goals are normally in conflict for conventional porous materials, but may be reconciled by the design and synthesis of new adsorbent materials with tailored pore size distributions and minimal macroporosity. Carbon nanotubes offer the possibility to explore new designs for adsorbents because they can be fabricated with small size distributions, and naturally tend to self-assemble by van der Waals forces. This year we report heats of adsorption for hydrogen on nanotube materials that are 2 and 3 times greater than for hydrogen on activated carbon. The hydrogen which is most strongly bound to these materials remains on the carbon surface to temperatures greater than 285 K. These results suggest that nanocapillary forces are active in stabilizing hydrogen on the surfaces of carbon nanotubes, and that optimization of the adsorbent will lead to effective storage at higher temperatures. In this paper we will also report on our activities which are targeted at understanding and optimizing the nucleation and growth of single wall nanotubes. These experiments were made possible by the development of a unique feedback control circuit which stabilized the plasma-arc during a synthesis run.

  16. Fabrication of carbon/SiO2 composites from the hydrothermal carbonization process of polysaccharide and their adsorption performance.

    Science.gov (United States)

    Li, Yinhui; Li, Kunyu; Su, Min; Ren, Yanmei; Li, Ying; Chen, Jianxin; Li, Liang

    2016-11-20

    In this work, carbon/SiO2 composites, using amylose and tetraethyl orthosilicate (TEOS) as raw materials, were successfully prepared by a facial hydrothermal carbonization process. The carbon/SiO2 composites were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), Energy Dispersive Spectroscopy (EDS), transmission electron microscope (TEM), N2 adsorption and Thermogravimetric (TG) analysis. The composites, which were made up of amorphous SiO2 and amorphous carbon, were found to have hierarchical porous structures. The mass ratios of amylose and SiO2 and the hydrothermal carbonization time had significant effects on the morphology of the composites, which had three shapes including monodispersed spheres, porous pieces and the nano-fibers combined with nano-spheres structures. The adsorption performance of the composites was studied using Pb(2+) as simulated contaminants from water. When the mass ratio of amylose and SiO2 was 9/1, the hydrothermal time was 30h and the hydrothermal temperature was 180°C, the adsorption capacity of the composites achieved to 52mg/g. Experimental data show that adsorption kinetics of the carbon/SiO2 composites can be fitted well by the Elovich model, while the isothermal data can be perfectly described by the Langmuir adsorption model and Freundlich adsorption model. The maximum adsorption capacity of the carbon/SiO2 composites is 56.18mgg(-1).

  17. Evolution of Electronic Circuits using Carbon Nanotube Composites

    Science.gov (United States)

    Massey, M. K.; Kotsialos, A.; Volpati, D.; Vissol-Gaudin, E.; Pearson, C.; Bowen, L.; Obara, B.; Zeze, D. A.; Groves, C.; Petty, M. C.

    2016-08-01

    Evolution-in-materio concerns the computer controlled manipulation of material systems using external stimuli to train or evolve the material to perform a useful function. In this paper we demonstrate the evolution of a disordered composite material, using voltages as the external stimuli, into a form where a simple computational problem can be solved. The material consists of single-walled carbon nanotubes suspended in liquid crystal; the nanotubes act as a conductive network, with the liquid crystal providing a host medium to allow the conductive network to reorganise when voltages are applied. We show that the application of electric fields under computer control results in a significant change in the material morphology, favouring the solution to a classification task.

  18. Evolution of Electronic Circuits using Carbon Nanotube Composites.

    Science.gov (United States)

    Massey, M K; Kotsialos, A; Volpati, D; Vissol-Gaudin, E; Pearson, C; Bowen, L; Obara, B; Zeze, D A; Groves, C; Petty, M C

    2016-08-25

    Evolution-in-materio concerns the computer controlled manipulation of material systems using external stimuli to train or evolve the material to perform a useful function. In this paper we demonstrate the evolution of a disordered composite material, using voltages as the external stimuli, into a form where a simple computational problem can be solved. The material consists of single-walled carbon nanotubes suspended in liquid crystal; the nanotubes act as a conductive network, with the liquid crystal providing a host medium to allow the conductive network to reorganise when voltages are applied. We show that the application of electric fields under computer control results in a significant change in the material morphology, favouring the solution to a classification task.

  19. Evolution of Electronic Circuits using Carbon Nanotube Composites

    Science.gov (United States)

    Massey, M. K.; Kotsialos, A.; Volpati, D.; Vissol-Gaudin, E.; Pearson, C.; Bowen, L.; Obara, B.; Zeze, D. A.; Groves, C.; Petty, M. C.

    2016-01-01

    Evolution-in-materio concerns the computer controlled manipulation of material systems using external stimuli to train or evolve the material to perform a useful function. In this paper we demonstrate the evolution of a disordered composite material, using voltages as the external stimuli, into a form where a simple computational problem can be solved. The material consists of single-walled carbon nanotubes suspended in liquid crystal; the nanotubes act as a conductive network, with the liquid crystal providing a host medium to allow the conductive network to reorganise when voltages are applied. We show that the application of electric fields under computer control results in a significant change in the material morphology, favouring the solution to a classification task. PMID:27558444

  20. Functional Carbon Materials for Electrochemical Energy Storage

    Science.gov (United States)

    Zhou, Huihui

    The ability to harvest and convert solar energy has been associated with the evolution of human civilization. The increasing consumption of fossil fuels since the industrial revolution, however, has brought to concerns in ecological deterioration and depletion of the fossil fuels. Facing these challenges, humankind is forced to seek for clean, sustainable and renewable energy resources, such as biofuels, hydraulic power, wind power, geothermal energy and other kinds of alternative energies. However, most alternative energy sources, generally in the form of electrical energy, could not be made available on a continuous basis. It is, therefore, essential to store such energy into chemical energy, which are portable and various applications. In this context, electrochemical energy-storage devices hold great promises towards this goal. The most common electrochemical energy-storage devices are electrochemical capacitors (ECs, also called supercapacitors) and batteries. In comparison to batteries, ECs posses high power density, high efficiency, long cycling life and low cost. ECs commonly utilize carbon as both (symmetric) or one of the electrodes (asymmetric), of which their performance is generally limited by the capacitance of the carbon electrodes. Therefore, developing better carbon materials with high energy density has been emerging as one the most essential challenges in the field. The primary objective of this dissertation is to design and synthesize functional carbon materials with high energy density at both aqueous and organic electrolyte systems. The energy density (E) of ECs are governed by E = CV 2/2, where C is the total capacitance and V is the voltage of the devices. Carbon electrodes with high capacitance and high working voltage should lead to high energy density. In the first part of this thesis, a new class of nanoporous carbons were synthesized for symmetric supercapacitors using aqueous Li2SO4 as the electrolyte. A unique precursor was adopted to

  1. Numerical simulation of isothermal chemical vapor infiltration process in fabrication of carbon-carbon composites by finite element method

    Institute of Scientific and Technical Information of China (English)

    李克智; 李贺军; 姜开宇

    2000-01-01

    The chemical vapor infiltration process in fabrication of carbon-carbon composites is highly inefficient and requires long processing time. These limitations add considerably to the cost of fabrication and restrict the application of this material. Efforts have been made to study the CVI process in fabrication of carbon-carbon composites by computer simulation and predict the process parameters, density, porosity, etc. According to the characteristics of CVI process, the basic principle of FEM and mass transport, the finite element model has been established. Incremental finite element equations and the elemental stiffness matrices have been derived for the first time. The finite element program developed by the authors has been used to simulate the ICVI process in fabrication of carbon-carbon composites. Computer color display of simulated results can express the densification and distributions of density and porosity in preform clearly. The influence of process parameters on the densification of prefo

  2. Composite Materials and Sandwich Structures - A Primer

    Science.gov (United States)

    2010-05-01

    quality and protects prepreg from handling damage. Non - woven unidirectional tapes can otherwise split between fibers. Clean, white lint-free cotton ...applications and S glass fibers are used in strength critical situations. S glass fibers are sometimes woven in composite materials to increase toughness...A woven form of the reinforcements (Figure 1b) is also used in certain cases, depending on the application of the composite. Figure 1a- Fiber

  3. Research on Composite Materials for Structural Design.

    Science.gov (United States)

    1984-04-01

    Residual Stresses in Composite Laminates", (August 1983); the M.Sc. thesis of E.J. Porth , titled "Effect of an External Stress on Moisture Diffusion in...Rates in OUnidirectional Double Cantilevered Beam Fracture Toughness Specimens", December 1982. 4. Porth , E.J., "Effect of an External Stress on...Composite Materials (December 1983) Edward John Porth , B.S., University of Colorado Chairman of Advisory Committee: Dr. Y. Weitsman This work concerns

  4. Life of structures of composite materials

    Energy Technology Data Exchange (ETDEWEB)

    Koznetsov, N.D.; Stepanenko, N.D.

    1986-06-01

    The introduction of composite materials in gas turbine engines is rationally done in stages. It is desirable to concentrate efforts on the use of them for production of vanes, sound deadening panes, the reverse rod, and other elements of the stator. The authors use compressor blades as an example of the basic principles of design, the selection of the reinforcing structure, and inspection of the quality of structures of composite materials. A method of determination of the elastodamping properties of polymer composite materials on specimens with free ends in high frequency flexural vibrations excited by a modulated jet of compressed air has been developed and standardized. With the use of this method such defects as separations, cracks, disorientation of the reinforcing, deviations in the order of alternation and the angular orientation of the layers are revealed.

  5. New composite materials for optoelectronic applications

    Science.gov (United States)

    Iovu, M. S.; Buzurniuc, S. A.; Verlan, V. I.; Culeac, I. P.; Nistor, Yu. H.

    2009-01-01

    The problem of obtaining low cost but efficient luminescent materials is still actually. Data concerning fabrication and luminescent properties of new composite materials on the base of thenoyltrifluoroacetone (TTA) of Europium(III) (Eu(TTA)3) and chalcogenide glasses doped with rare earth ions and polymers are presented. The visible emission spectra of the composites on the base of Eu(TTA)3 structured with phenantroline (Eu(TTA)3Phen) and copolymer from styrene and butylmethacrylate (1:1)(SBMA) under the excitation with N2-laser (λ=337 nm) contain sharp emission bands located at 354, 415, 580, 587, 590, 596, 611.4, 616.5, 621, 652, 690, 700, 713 nm. The nature of the observed emission bands and the possible mechanisms of the radiative electron transition in the investigated composite materials are discussed.

  6. Preparation and Electrochemical Properties of Selenium Nanoparticles/Multiwall Carbon Nanotubes Composite Materials%纳米硒/多壁碳纳米管复合材料的制备及其电化学性能

    Institute of Scientific and Technical Information of China (English)

    荣凤霞; 周俊; 刘薇; 王锐; 白燕

    2011-01-01

    The multiwall carbon nanotubes(MWCNTs) were treated by concentrated H2SO4/HNO3 mixtures. The selenium nanoparticles/multiwall carbon nanotubes composite materials (nano-Se0/MWCNTs for short 1) was prepared by MWCNTs loaded nano-Se0. The structure and mopography of 1 were characterized by IR, TEM and SEM. The electrochemical properties of 1 were investigated by cyclic voltammetry and electrochemical impedance spectra.%经混酸纯化处理的多壁碳纳米管(MWCNTs)负载纳米硒(Nano-Se0)制备纳米硒/多壁碳纳米管复合材料(Nano-Se0/MWCNTs,简称1),其结构经IR,TEM和SEM表征.以Fe(CN)4-/3-6 为探针离子,采用循环伏安法和电化学阻抗法考察了1的电化学性能.

  7. Use of Carbon Fiber Composite Molecular Sieves for Air Separation

    Energy Technology Data Exchange (ETDEWEB)

    Baker, Frederick S [ORNL; Contescu, Cristian I [ORNL; Gallego, Nidia C [ORNL; Burchell, Timothy D [ORNL

    2005-09-01

    A novel adsorbent material, 'carbon fiber composite molecular sieve' (CFCMS), has been developed by the Oak Ridge National Laboratory. Its features include high surface area, large pore volume, and a rigid, permeable carbon structure that exhibits significant electrical conductivity. The unique combination of high adsorptive capacity, permeability, good mechanical properties, and electrical conductivity represents an enabling technology for the development of novel gas separation and purification systems. In this context, it is proposed that a fast-cycle air separation process that exploits a kinetic separation of oxygen and nitrogen should be possible using a CFCMS material coupled with electrical swing adsorption (ESA). The adsorption of O{sub 2}, N{sub 2}, and CO{sub 2} on activated carbon fibers was investigated using static and dynamic techniques. Molecular sieving effects in the activated carbon fiber were highlighted by the adsorption of CO{sub 2}, a more sensitive probe molecule for the presence of microporosity in adsorbents. The kinetic studies revealed that O2 was more rapidly adsorbed on the carbon fiber than N{sub 2}, and with higher uptake under equilibrium conditions, providing the fiber contained a high proportion of very narrow micropores. The work indicated that CFCMS is capable of separating O{sub 2} and N{sub 2} from air on the basis of the different diffusion rates of the two molecules in the micropore network of the activated carbon fibers comprising the composite material. In response to recent enquires from several potential users of CFCMS materials, attention has been given to the development of a viable continuous process for the commercial production of CFCMS material. As part of this effort, work was implemented on characterizing the performance of lignin-based activated carbon fiber, a potentially lower cost fiber than the pitch-based fibers used for CFCMS production to date. Similarly, to address engineering issues

  8. Preparation of PAN/phenolic-based carbon/carbon composites with flexible towpreg carbon fiber

    Energy Technology Data Exchange (ETDEWEB)

    Li Wei [College of Materials Science and Engineering, Hunan University, Changsha 410082 (China)], E-mail: liwei5168@hnu.cn; Chen Zhenhua; Li Jin; Chen Xianhong; Xuan Hao; Wang Xiaoyi [College of Materials Science and Engineering, Hunan University, Changsha 410082 (China)

    2008-06-25

    Carbon/carbon composites made with flexible towpreg carbon fiber as reinforcement and phenolic resins as matrix precursor were impregnated with pitch during re-carbonization process. The structural characteristics of the composites were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), three-point bending tests, Archimedes' method and water adsorption. Results showed that the density of the carbon/carbon composites increases from 1.45 to 1.54 g/cm{sup 3} with the cycles of pitch impregnated and re-carbonization. Open porosity measurement indicated that the increase of porosity resulted from the decomposition of phenolic resin matrix, and the open porosity of the composite gradually decreased after the impregnation and re-carbonization process. These composites also exhibited an improvement in flexural strength with increasing number of densification cycles. From SEM morphological observation, it was concluded that few cracks appeared in the surfaces and a few smaller pores with a diameter <1 {mu}m could be observed.

  9. Electron Field Emission from Nanostructured Carbon Materials

    Science.gov (United States)

    Gupta, Sanju

    2005-03-01

    Fabricating small structures has almost become fashionable and the rationale is that reducing one or more dimensions below some critical length changes the systems' physical properties drastically, where nanocrystalline diamond (n-D) and carbon nanotubes (CNTs) in the class of advanced carbon materials serve model examples. Emission of electrons at room temperature - cold electron emitters - are of vital importance for a variety of vacuum microelectronic devices - electron microscopes, photo multipliers, X-ray generators, lamps, and flat panel displays and microwave cathodes. Electron emitters may lead to otherwise difficult to obtain advantages in performance and/or design. This is the driving force to investigate the carbon-related materials as cold cathodes. In this talk, the performance of various forms of carbon in thin film form including diamond, n-D, and vertically aligned CNTs as cold cathodes for their potential use in field emission displays (FEDs) in terms of I-V characteristics and corresponding spatial imaging will be presented. Physics based models such as, NEA, surface modification, geometric enhancement, and microstructure alteration due to particle bombardment, and doping, will be described to support the experimental observations of electron field enhancement (low turn-on voltage, high current and emission site density) and its reliability from the abovementioned carbon-related materials. Other vacuum device applications such as thermionic power generators will be mentioned briefly.

  10. Health monitoring method for composite materials

    Science.gov (United States)

    Watkins, Jr., Kenneth S.; Morris, Shelby J.

    2011-04-12

    An in-situ method for monitoring the health of a composite component utilizes a condition sensor made of electrically conductive particles dispersed in a polymeric matrix. The sensor is bonded or otherwise formed on the matrix surface of the composite material. Age-related shrinkage of the sensor matrix results in a decrease in the resistivity of the condition sensor. Correlation of measured sensor resistivity with data from aged specimens allows indirect determination of mechanical damage and remaining age of the composite component.

  11. Pyrolytic carbon black composite and method of making the same

    Energy Technology Data Exchange (ETDEWEB)

    Naskar, Amit K.; Paranthaman, Mariappan Parans; Bi, Zhonghe

    2016-09-13

    A method of recovering carbon black includes the step of providing a carbonaceous source material containing carbon black. The carbonaceous source material is contacted with a sulfonation bath to produce a sulfonated material. The sulfonated material is pyrolyzed to produce a carbon black containing product comprising a glassy carbon matrix phase having carbon black dispersed therein. A method of making a battery electrode is also disclosed.

  12. Evaluation of novel Ti-doped 3D carbon-carbon composites under transient thermal loads

    Energy Technology Data Exchange (ETDEWEB)

    Centeno, A. [Instituto Nacional del Carbon (CSIC), Apdo. 73, 33080-Oviedo (Spain); Blanco, C., E-mail: clara@incar.csic.e [Instituto Nacional del Carbon (CSIC), Apdo. 73, 33080-Oviedo (Spain); Santamaria, R.; Granda, M.; Menendez, R. [Instituto Nacional del Carbon (CSIC), Apdo. 73, 33080-Oviedo (Spain); Pintsuk, G.; Linke, J. [Forschungszentrum Juelich GmbH, EURATOM Association, 52425-Juelich (Germany)

    2010-08-15

    3D Ti-doped and undoped carbon-carbon composites (CFCs) were exposed to transient thermal loads to simulate plasma disruptions, in the electron beam test facility JUDITH at different power densities and multiple shots in order to study the evolution in the behavior of the material. The thermal shock response of the undoped and Ti-doped materials was compared in order to study the influence of titanium carbide as dopant. The erosion itself is driven during the first shots by macroscopic erosion (brittle destruction), which is a result of thermally induced stresses. With increasing number of shots, no more brittle destruction is observed and the main erosion mechanism is sublimation due to local overheating. This is also confirmed by the decrease of the erosion rate with increasing the number of shots. The pitch fibers are hardly affected by the applied heat loads and they show almost no erosion, especially in the Ti-doped composite.

  13. Effect of Metal Additives on Performance of Low-Carbon Magnesia-Carbon Materials

    Institute of Scientific and Technical Information of China (English)

    PENG Xiaoyan; LI Lin; HE Zhiyong; LIU Kaiqi; WANG Bingjun

    2007-01-01

    In this paper, both oxidation and corrosion resistance of low-carbon magnesia-carbon materials containing 4.0wt% graphite with metallic Al and Mg-Al alloy powders as antioxidants were investigated. Meanwhile,the microstructures of samples corroded by slag were observed with optical microscope as well. The test results revealed the properties of oxidation and corrosion resistance of low-carbon magnesia-carbon materials could be improved obviously by adding metal Al powder and Mg-Al alloy powder. The rule of improving oxidation resistance was illegibility when metal Al powder and Mg-Al alloy powder were added together. It was harmful to corrosion resistance by mixed adding metal Al powder and Mg-Al alloy powder into the materials, at the same time, the corrosion resistance would decreased with the increasing of Mg-Al alloy content. The corrosion resistance of samples with 0.5wt% or 3.0wt% Mg-Al alloy was better. The oxidation resistance and corrosion resistance of materials with metal Al or Mg-Al alloy respectively were better than that with mixed metal Al and Mg-Al alloy. As a result, Mg-Al alloy was more suitable for low-carbon composite materials than metal Al as additives.

  14. Mechanical properties of carbon fiber composites for applications in space

    Science.gov (United States)

    Hana, P.; Inneman, A.; Daniel, V.; Sieger, L.; Petru, M.

    2015-01-01

    This article describes method of measurement mechanical properties of carbon fiber composites in space. New material structures are specifically designed for use on space satellites. Composite structures will be exposed to cosmic radiation in Earth orbit on board of a '2U CubeSat' satellite. Piezoelectric ceramic sensors are used for detection mechanical vibrations of composite test strip. A great deal of attention is paid to signal processing using 8-bit microcontroler. Fast Fourier Transformation is used. Fundamental harmonic frequencies and damping from on-board measurements will serve as the input data for terrestrial data processing. The other step of elaboration data is creation of the physical model for evaluating mechanical properties of Carbon composite - Piezoelectric ceramic system. Evaluation of anisotropic mechanical properties of piezoelectric ceramics is an interesting secondary outcome of the investigation. Extreme changes in temperature and the effect of cosmic rays will affect the mechanical properties and durability of the material used for the external construction of satellites. Comparative terrestrial measurements will be performed.

  15. Effect of carbon nanotubes upon emissions from cutting and sanding carbon fiber-epoxy composites

    Energy Technology Data Exchange (ETDEWEB)

    Heitbrink, William A. [LMK OSH Consulting LLC (United States); Lo, Li-Ming, E-mail: LLo@cdc.gov [Centers for Disease Control and Prevention (CDC), Division of Applied Research and Technology, National Institute for Occupational Safety and Health (NIOSH) (United States)

    2015-08-15

    Carbon nanotubes (CNTs) are being incorporated into structural composites to enhance material strength. During fabrication or repair activities, machining nanocomposites may release CNTs into the workplace air. An experimental study was conducted to evaluate the emissions generated by cutting and sanding on three types of epoxy-composite panels: Panel A containing graphite fibers, Panel B containing graphite fibers and carbon-based mat, and Panel C containing graphite fibers, carbon-based mat, and multi-walled CNTs. Aerosol sampling was conducted with direct-reading instruments, and filter samples were collected for measuring elemental carbon (EC) and fiber concentrations. Our study results showed that cutting Panel C with a band saw did not generate detectable emissions of fibers inspected by transmission electron microscopy but did increase the particle mass, number, and EC emission concentrations by 20–80 % compared to Panels A and B. Sanding operation performed on two Panel C resulted in fiber emission rates of 1.9 × 10{sup 8} and 2.8 × 10{sup 6} fibers per second (f/s), while no free aerosol fibers were detected from sanding Panels A and B containing no CNTs. These free CNT fibers may be a health concern. However, the analysis of particle and EC concentrations from these same samples cannot clearly indicate the presence of CNTs, because extraneous aerosol generation from machining the composite epoxy material increased the mass concentrations of the EC.

  16. Alignment and Load Transfer in Carbon Nanotube and Dicyclopentadiene Composites

    Science.gov (United States)

    Severino, Joseph Vincent

    Individual carbon nanotubes (CNTs) are the strongest materials available but their macroscopic assemblies are weak. This work establishes a new thermosetting dicyclopentadiene (DCPD) and CNT composite that increases the strength of CNT assemblies. These high volume fraction and void free structures constitute advanced materials that could one day replace traditional composite systems. To further the understanding of physical interactions between polymer and CNTs, a novel "capstan" load transfer mechanism is also introduced. Self-supporting assemblies of interconnected carbon nanotubes were stretched, twisted and compressed to fashion composites by the infusion and polymerization of low viscosity DCPD based monomeric resins. The properties of the CNTs, polymer and composite were characterized with thermal gravimetric analysis (TGA), dynamic mechanical analysis (DMA) and Raman spectroscopy. The microstructure was analyzed by wide angle X-ray scattering (WAXS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Sheets were drawn at 15 m/min from a growth furnace to impart alignment then stretched to further modify alignment. The mechanical properties were determined in five orientations with respect to the growth direction. The strength was nearly three times higher along this growth direction than it was perpendicular, and modulus was nearly six times higher. Transverse stretching achieved 1.5 times the elongation but alignment was inferior due to CNT kinking that prevented alignment and consolidation. Composites yarns and sheets were investigated for the mechanical properties, microstructure and load transfer. The DCPD resin was found to wet the CNTs and lubricated deformation. This reduced loads during processing, and curing solidified the aligned and consolidated structure. The stretched and twisted composite yarns increased the failure stress 51%. In aligned composite sheet, the failure stress increased 200%. The increased stresses

  17. RADIATION EFFECTS ON EPOXY/CARBON FIBER COMPOSITE

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, E; Eric Skidmore, E

    2008-12-12

    The Department of Energy Savannah River Site vitrifies nuclear waste incident to defense programs through its Defense Waste Processing Facility (DWPF). The piping in the DWPF seal pot jumper configuration must withstand the stresses during an unlikely but potential deflagration event, and maintain its safety function for a 20-year service life. Carbon fiber-reinforced epoxy composites (CFR) were proposed for protection and reinforcement of piping during such an event. The proposed CFR materials have been ASME-approved (Section XI, Code Case N-589-1) for post-construction maintenance and is DOT-compliant per 49CFR 192 and 195. The proposed carbon fiber/epoxy composite reinforcement system was originally developed for pipeline rehabilitation and post-construction maintenance in petrochemical, refineries, DOT applications and other industries. The effects of ionizing radiation on polymers and organic materials have been studied for many years. The majority of available data are based on traditional exposures to gamma irradiation at high dose rates ({approx}10,000 Gy/hr) allowing high total dose within reasonable test periods and general comparison of different materials exposed at such conditions. However, studies in recent years have shown that degradation of many polymers are sensitive to dose rate, with more severe degradation often observed at similar or even lower total doses when exposed to lower dose rates. This behavior has been primarily attributed to diffusion-limited oxidation which is minimized during very high dose rate exposures. Most test standards for accelerated aging and nuclear qualification of components acknowledge these limitations. The results of testing to determine the radiation resistance and microstructural effects of gamma irradiation exposure on a bisphenol-A based epoxy matrix composite reinforced with carbon fibers are presented. This work provides a foundation for a more extensive evaluation of dose rate effects on advanced epoxy

  18. Fatigue properties of unidirectional carbon fibre composites at cryogenic temperatures

    Science.gov (United States)

    Pannkoke, K.; Wagner, H.-J.

    Design engineers working with composite materials are still confronted with uncertainties as to their fatigue behaviour, especially for cryogenic applications. In the course of cooling, different thermal contraction of the fibre and matrix gives rise to thermal stresses and strains which influence most of the mechanical properties. In this paper, the fatigue behaviour of unidirectional (UD) composites with different fibres and matrices will be described. A first step in understanding the failure mechanism under cyclic loading will be presented. In earlier tests excellent fatigue properties were found for carbon fibre UD composites made of T300 carbon fibres and an epoxy matrix 1,2. However, the applied epoxy resin was brittle, especially at low temperatures. Therefore the brittle resin was substituted by polycarbonate (PC), a tough thermoplastic polymer 3,4. Nevertheless, for a composite with that matrix the fatigue endurance limit, normalized to the static strength, was found to be much lower (43%). SEM studies illustrated a poor fibre - matrix bond. To determine the bond's influence on fatigue properties, another tough matrix system was tested. The polymer PEEK is known to build a strong bond to carbon fibres, initiated by crystal growth onto the fibre surface 4,5. However, investigations on the fatigue behaviour of this composite at 77 K yielded the same low fatigue endurance limit as was found for the carbon fibre - PC system 4. At this point it can be concluded that the poor fatigue behaviour is not necessarily due to a strong or poor fibre - matrix bond. It is the purpose of this work to examine whether this different fatigue behaviour is due to matrix failure.

  19. Scaling Laws and Mesoscopic Modeling of Heat Transfer in Nanofibrous Materials and Composites

    Science.gov (United States)

    2013-11-26

    buckypaper, and other materials composed of carbon nanotubes (CNTs), individual CNTs are bound together by van der Waals forces and form entangled...for nanofibrous materials based on carbon nanotubes (CNTs) are investigated by performing a multiscale computational study combining atomistic...composition on the ejection and transport of polymer molecules and carbon nanotubes in matrix-assisted pulsed laser evaporation, Appl. Phys. A 105, 529

  20. A Comprehensive Review of Gas Sensors Using Carbon Materials.

    Science.gov (United States)

    Kim, Min Il; Lee, Young-Seak

    2016-05-01

    In recent years, interest in carbon materials for use in gas sensors has increased. Carbon materials have unique electrical, optical and mechanical properties, making these materials very interesting. In this review, the properties of carbon materials are first introduced. Surface modification for carbon materials, fabrication for gas sensors, and the gas-sensing conditions and mechanisms according to the different types of carbon materials are chiefly described. In particular, this review focuses on the enhancement of the gas-sensing properties of carbon materials depending on the modification methods used and its mechanism.

  1. Materials design for electrocatalytic carbon capture

    Science.gov (United States)

    Tan, Xin; Tahini, Hassan A.; Smith, Sean C.

    2016-05-01

    We discuss our philosophy for implementation of the Materials Genome Initiative through an integrated materials design strategy, exemplified here in the context of electrocatalytic capture and separation of CO2 gas. We identify for a group of 1:1 X-N graphene analogue materials that electro-responsive switchable CO2 binding behavior correlates with a change in the preferred binding site from N to the adjacent X atom as negative charge is introduced into the system. A reconsideration of conductive N-doped graphene yields the discovery that the N-dopant is able to induce electrocatalytic binding of multiple CO2 molecules at the adjacent carbon sites.

  2. MNi4.8Sn0.2(M=La,Nd)-supported multi-walled carbon nanotube composites as hydrogen storase materials

    Institute of Scientific and Technical Information of China (English)

    REN JianWei; LIAO ShiJun; LIU JunMin

    2007-01-01

    Two composites LaNi4.8Sn0.2/CNTs and NdNi4.8Sn0.2/CNTs were prepared by an impregnation-reduction method.Their hydrogen storage capacity could reach up to 2.96 wt% and 2.88 wt% respectively at room temperature and 1.0 MPa pressure.These values,which might result from the synergetic effect between the alloy nanoparticles and the pretreated CNTs,were three times higher than those of the unsupported MNi4.8Sn0.2(M=La,Nd)alloys under the same conditions.XRD and TEM revealed that the alloy particles were uniformly dispersed on the CNTs and the average particle size was ca.30 nm.The composites also showed good stability and the hydrogen storage capacity decreased by less than 6% after 100 adsorption-desorption cycles.Moreover,no noticeable change in crystalline structure was bserved for the composites.

  3. Multiaxial analysis of dental composite materials.

    Science.gov (United States)

    Kotche, Miiri; Drummond, James L; Sun, Kang; Vural, Murat; DeCarlo, Francesco

    2009-02-01

    Dental composites are subjected to extreme chemical and mechanical conditions in the oral environment, contributing to the degradation and ultimate failure of the material in vivo. The objective of this study is to validate an alternative method of mechanically loading dental composite materials. Confined compression testing more closely represents the complex loading that dental restorations experience in the oral cavity. Dental composites, a nanofilled and a hybrid microfilled, were prepared as cylindrical specimens, light-cured in ring molds of 6061 aluminum, with the ends polished to ensure parallel surfaces. The samples were subjected to confined compression loading to 3, 6, 9, 12, and 15% axial strain. Upon loading, the ring constrains radial expansion of the specimen, generating confinement stresses. A strain gage placed on the outer wall of the aluminum confining ring records hoop strain. Assuming plane stress conditions, the confining stress (sigma(c)) can be calculated at the sample/ring interface. Following mechanical loading, tomographic data was generated using a high-resolution microtomography system developed at beamline 2-BM of the Advanced Photon Source at Argonne National Laboratory. Extraction of the crack and void surfaces present in the material bulk is numerically represented as crack edge/volume (CE/V), and calculated as a fraction of total specimen volume. Initial results indicate that as the strain level increases the CE/V increases. Analysis of the composite specimens under different mechanical loads suggests that microtomography is a useful tool for three-dimensional evaluation of dental composite fracture surfaces.

  4. Composite material pedestrian bridge for the Port of Bilbao

    Science.gov (United States)

    Gorrochategui, I.; Manteca, C.; Yedra, A.; Miguel, R.; del Valle, F. J.

    2012-09-01

    Composite materials in comparison to traditional ones, steel and concrete, present advantages in civil works construction: lower weight, higher corrosion resistance (especially in the marine environment), and ease of installation. On the other hand, fabrication costs are generally higher. This is the reason why this technology is not widely used. This work illustrates the process followed for the design, fabrication and installation of a composite material pedestrian bridge in the Port of Bilbao (Northern Spain). In order to reduce the price of the bridge, the use of low cost materials was considered, therefore polyester resin was selected as the polymeric matrix, and glass fibres as reinforcement. Two material choices were studied. Currently in the market there is high availability of carbon nanoparticles: carbon nanotubes (CNT) and carbon nanofibres (CNF), so it was decided to add this kind of nanoparticles to the reference material with the objective of improving its mechanical properties. The main challenge was to transfer the CNT and CNF excellent properties to the polymeric matrix. This requires dispersing the nanoreinforcements as individual particles in the polymeric matrix to avoid agglomerates. For this reason, an advanced high shear forces dispersion technique (called "three roll mills") was studied and implemented. Also surface functionalization of the nanoreinforcements by chemical treatment was carried out. Herein, a comparison is performed between both materials studied, the explanation of the employment of the reference material (without nanoreinforcement) as the one used in the fabrication of the pedestrian bridge is justified and, finally, the main characteristics of the final design of the structural element are described.

  5. Composite materials for rail transit systems

    Science.gov (United States)

    Griffin, O. Hayden, Jr.; Guerdal, Zafer; Herakovich, Carl T.

    1987-01-01

    The potential is explored for using composite materials in urban mass transit systems. The emphasis was to identify specific advantages of composite materials in order to determine their actual and potential usage for carbody and guideway structure applications. The literature was reviewed, contacts were made with major domestic system operators, designers, and builders, and an analysis was made of potential composite application to railcar construction. Composites were found to be in use throughout the transit industry, usually in secondary or auxiliary applications such as car interior and nonstructural exterior panels. More recently, considerable activity has been initiated in the area of using composites in the load bearing elements of civil engineering structures such as highway bridges. It is believed that new and improved manufacturing refinements in pultrusion and filament winding will permit the production of beam sections which can be used in guideway structures. The inherent corrosion resistance and low maintenance characteristics of composites should result in lowered maintenance costs over a prolonged life of the structure.

  6. Modeling the Mechanical Behavior of Ceramic Matrix Composite Materials

    Science.gov (United States)

    Jordan, William

    1998-01-01

    Ceramic matrix composites are ceramic materials, such as SiC, that have been reinforced by high strength fibers, such as carbon. Designers are interested in using ceramic matrix composites because they have the capability of withstanding significant loads while at relatively high temperatures (in excess of 1,000 C). Ceramic matrix composites retain the ceramic materials ability to withstand high temperatures, but also possess a much greater ductility and toughness. Their high strength and medium toughness is what makes them of so much interest to the aerospace community. This work concentrated on two different tasks. The first task was to do an extensive literature search into the mechanical behavior of ceramic matrix composite materials. This report contains the results of this task. The second task was to use this understanding to help interpret the ceramic matrix composite mechanical test results that had already been obtained by NASA. Since the specific details of these test results are subject to the International Traffic in Arms Regulations (ITAR), they are reported in a separate document (Jordan, 1997).

  7. Candida albicans adhesion to composite resin materials.

    Science.gov (United States)

    Bürgers, Ralf; Schneider-Brachert, Wulf; Rosentritt, Martin; Handel, Gerhard; Hahnel, Sebastian

    2009-09-01

    The adhesion of Candida albicans to dental restorative materials in the human oral cavity may promote the occurrence of oral candidosis. This study aimed to compare the susceptibility of 14 commonly used composite resin materials (two compomers, one ormocer, one novel silorane, and ten conventional hybrid composites) to adhere Candida albicans. Differences in the amount of adhering fungi should be related to surface roughness, hydrophobicity, and the type of matrix. Cylindrical specimens of each material were made according to the manufacturers' instructions. Surface roughness R (a) was assessed by perthometer measurements and the degree of hydrophobicity by computerized contact angle analysis. Specimens were incubated with a reference strain of C. albicans (DMSZ 1386), and adhering fungi were quantified by using a bioluminometric assay in combination with an automated plate reader. Statistical differences were analyzed by the Kruskal-Wallis test and Mann-Whitney U test. Spearman's rank correlation coefficients were calculated to assess correlations. Median R (a) of the tested composite resin materials ranged between 0.04 and 0.23 microm, median contact angles between 69.2 degrees and 86.9 degrees . The two compomers and the ormocer showed lower luminescence intensities indicating less adhesion of fungi than all tested conventional hybrid composites. No conclusive correlation was found between surface roughness, hydrophobicity, and the amount of adhering C. albicans.

  8. Multifunctional Carbon Electromagnetic Materials, Motors, and Actuators Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The purpose of the proposal is to apply multifunctional carbon electromagnetic materials, including carbon nanotube electrical thread (replaces copper wire) and...

  9. On the isotopic composition of magmatic carbon in SNC meteorites

    Science.gov (United States)

    Wright, I. P.; Grady, M. M.; Pillinger, C. T.

    1992-01-01

    SNC meteorites are thought, from many lines of evidence, to come from Mars. A line of investigation which has been pursued in our laboratory over the years involves measurement of the stable isotopic composition of carbon, in its various forms, in SNC meteorites. In order to establish a firm basis for studying the isotopic systematics of carbon in the martian surface environment, it is first necessary to try and constrain the delta C-13 of bulk Mars. Taking all of the available information, it would seem that the delta C-13 of the Earth's mantle lies somewhere in the range of -5 to -7 percent. Preliminary assessment of magnetic carbon in SNC meteorites, would tend to suggest a delta C-13 of 20 to 30 percent, which is conspicuously different from that of the terrestrial mantle. It is not obvious why there should be such a difference between the two planets, although many explanations are possible. One of these possibilities, that previous delta C-13 measurements for magnetic carbon in SNC meteorites are in error to some degree, is being actively investigated. The most recent results seem to constrain the theta C-13 of the magnetic carbon in SNC meteorites to about -20 percent, which is not at odds with previous estimates. As such, it is considered that a detailed investigation of the carbon isotopic systematics of martian surface materials does have the necessary information with which to proceed.

  10. Electrical properties of foamed polypropylene/carbon black composites

    Science.gov (United States)

    Iliev, M.; Kotzev, G.; Vulchev, V.

    2016-02-01

    Polypropylene composites containing carbon black fillers were produced by vibration assisted extrusion process. Solid (unfoamed) composite samples were molded by conventional injection molding method, while structural foams were molded by a low pressure process. The foamed samples were evidenced to have a solid skin-foamed core structure which main parameters were found to depend on the quantity of material injected in the mold. The average bubbles' sizes and their distribution were investigated by scanning electron microscopy. It is established that the conductivity of the foamed samples gradually decreases when reducing the sample density. Nevertheless, the conductivity is found to be lower than the conductivity of the unfoamed samples both being of the same order. The flexural properties of the composites were studied and the results were discussed in the context of the structure parameters of the foamed samples.

  11. Quasi-Carbon Fibers and the Composites

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    @@The aim of this report is to study the properties of quasi-carbon fibers (QCF) prepared from the PAN fiber precursor by pyrolysis at a temperature between 400℃ and 1200℃. The resistivity of QCF with different heat-treated temperature (HTT) was investigated by a Hall-35 testing system,and the flexural properties of the result composites (QCFC) are also discussed. In addition, the scanning electronic microscope (SEM) was utilized to observe the surface morphology of QCF and the fracture section of QCFC obtained from flexural testing.

  12. Carbon nanotube reinforced hybrid composites: Computational modeling of environmental fatigue and usability for wind blades

    DEFF Research Database (Denmark)

    Dai, Gaoming; Mishnaevsky, Leon

    2015-01-01

    The potential of advanced carbon/glass hybrid reinforced composites with secondary carbon nanotube reinforcement for wind energy applications is investigated here with the use of computational experiments. Fatigue behavior of hybrid as well as glass and carbon fiber reinforced composites...... with the secondary CNT reinforcements (especially, aligned tubes) present superior fatigue performances than those without reinforcements, also under combined environmental and cyclic mechanical loading. This effect is stronger for carbon composites, than for hybrid and glass composites....... automatically using the Python based code. 3D computational studies of environment and fatigue analyses of multiscale composites with secondary nano-scale reinforcement in different material phases and different CNTs arrangements are carried out systematically in this paper. It was demonstrated that composites...

  13. On the elastic properties of carbon nanotube-based composites: modelling and characterization

    CERN Document Server

    Thostenson, E T

    2003-01-01

    The exceptional mechanical and physical properties observed for carbon nanotubes has stimulated the development of nanotube-based composite materials, but critical challenges exist before we can exploit these extraordinary nanoscale properties in a macroscopic composite. At the nanoscale, the structure of the carbon nanotube strongly influences the overall properties of the composite. The focus of this research is to develop a fundamental understanding of the structure/size influence of carbon nanotubes on the elastic properties of nanotube-based composites. Towards this end, the nanoscale structure and elastic properties of a model composite system of aligned multi-walled carbon nanotubes embedded in a polystyrene matrix were characterized, and a micromechanical approach for modelling of short fibre composites was modified to account for the structure of the nanotube reinforcement to predict the elastic modulus of the nanocomposite as a function of the constituent properties, reinforcement geometry and nanot...

  14. Accelerated aging of polymer composite bridge materials

    Science.gov (United States)

    Carlson, Nancy M.; Blackwood, Larry G.; Torres, Lucinda L.; Rodriguez, Julio G.; Yoder, Timothy S.

    1999-05-01

    Accelerated aging research on samples of composite materials and candidate UV protective coatings is determining the effects of six environmental factors on material durability. Candidate fastener materials are being evaluated to determine corrosion rates and crevice corrosion effects at load-bearing joints. This work supports field testing of a 30-ft long, 18-ft wide polymer matrix composite (PMC) bridge at the Idaho National Engineering and Environmental Laboratory. Durability results and sensor data form test with live loads provide information required for determining the cost/benefit measures to use in life-cycle planning, determining a maintenance strategy, establishing applicable inspection techniques, and establishing guidelines, standards and acceptance criteria for PMC bridges for use in the transportation infrastructure.

  15. Accelerated Aging of Polymer Composite Bridge Materials

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, Nancy Margaret; Blackwood, Larry Gene; Torres, Lucinda Laine; Rodriguez, Julio Gallardo; Yoder, Timothy Scott

    1999-03-01

    Accelerated aging research on samples of composite material and candidate ultraviolet (UV) protective coatings is determining the effects of six environmental factors on material durability. Candidate fastener materials are being evaluated to determine corrosion rates and crevice corrosion effects at load-bearing joints. This work supports field testing of a 30-ft long, 18-ft wide polymer matrix composite (PMC) bridge at the Idaho National Engineering and Environmental Laboratory (INEEL). Durability results and sensor data from tests with live loads provide information required for determining the cost/benefit measures to use in life-cycle planning, determining a maintenance strategy, establishing applicable inspection techniques, and establishing guidelines, standards, and acceptance criteria for PMC bridges for use in the transportation infrastructure.

  16. Preparation and characterization of grafted collagen-multiwalled carbon nanotubes composites.

    Science.gov (United States)

    Cao, Y; Zhou, Y M; Shan, Y; Ju, H X; Xue, X J

    2007-02-01

    This paper describes a new class of composite materials designed by combining multiwalled carbon nanotubes (MWCNTs) and grafted collagen matrix. These materials show high mechanical capabilities by taking advantage of the favorable mechanical characteristics of MWCNTs. Furthermore, doping carbon nanotubes into grafted collagen matrix results in a substantial improvement of thermal stability and infrared emissivity. Thus these materials possess potential applications in some fields such as biomedicine and infrared camouflage.

  17. Composite yarns of multiwalled carbon nanotubes with metallic electrical conductivity.

    Science.gov (United States)

    Randeniya, Lakshman K; Bendavid, Avi; Martin, Philip J; Tran, Canh-Dung

    2010-08-16

    Unique macrostructures known as spun carbon-nanotube fibers (CNT yarns) can be manufactured from vertically aligned forests of multiwalled carbon nanotubes (MWCNTs). These yarns behave as semiconductors with room-temperature conductivities of about 5 x 10(2) S cm(-1). Their potential use as, for example, microelectrodes in medical implants, wires in microelectronics, or lightweight conductors in the aviation industry has hitherto been hampered by their insufficient electrical conductivity. In this Full Paper, the synthesis of metal-CNT composite yarns, which combine the unique properties of CNT yarns and nanocrystalline metals to obtain a new class of materials with enhanced electrical conductivity, is presented. The synthesis is achieved using a new technique, self-fuelled electrodeposition (SFED), which combines a metal reducing agent and an external circuit for transfer of electrons to the CNT surface, where the deposition of metal nanoparticles takes place. In particular, the Cu-CNT and Au-CNT composite yarns prepared by this method have metal-like electrical conductivities (2-3 x 10(5) S cm(-1)) and are mechanically robust against stringent tape tests. However, the tensile strengths of the composite yarns are 30-50% smaller than that of the unmodified CNT yarn. The SFED technique described here can also be used as a convenient means for the deposition of metal nanoparticles on solid electrode supports, such as conducting glass or carbon black, for catalytic applications.

  18. High Volume Fraction Carbon Nanotube Composites for Aerospace Applications

    Science.gov (United States)

    Siochi, Emilie J.; Kim, Jae-Woo; Sauti, Godfrey; Cano, Roberto J.; Wincheski, Russell A.; Ratcliffe, James G.; Czabaj, Michael; Jensen, Benjamin D.; Wise, Kristopher E.

    2015-01-01

    Reported nanoscale mechanical properties of carbon nanotubes (CNTs) suggest that their use may enable the fabrication of significantly lighter structures for use in space applications. To be useful in the fabrication of large structures, however, their attractive nanoscale properties must be retained as they are scaled up to bulk materials and converted into practically useful forms. Advances in CNT production have significantly increased the quantities available for use in manufacturing processes, but challenges remain with the retention of nanoscale properties in larger assemblies of CNTs. This work summarizes recent progress in producing carbon nanotube composites with tensile properties approaching those of carbon fiber reinforced polymer composites. These advances were achieved in nanocomposites with CNT content of 70% by weight. The processing methods explored to yield these CNT composite properties will be discussed, as will the characterization and test methods that were developed to provide insight into the factors that contribute to the enhanced tensile properties. Technology maturation was guided by parallel advancements in computational modeling tools that aided in the interpretation of experimental data.

  19. Hybrid Matrices Layer of Carbon Fiber Composites

    Directory of Open Access Journals (Sweden)

    Dr. B. Balu Naik

    2013-04-01

    Full Text Available Polymeric composites have gone through a level of maturity beyond the laboratory stage with the development of all composite aircraft structures. Yet the basic understanding of the material used in its primary structure has not been extensively investigated. Although this may be attributed in part to the proprietary nature of the system, we believe that it is because of lack of specific tools required for its analysis.Specifically, micromechanical models always assume an evenly distributed homogeneous matrix while lamination theory assumes constant stress through the laminate thickness. Specifically, this work focuses on the development of model systems that can be studied without concerns of proprietary and/or export control requirements. Consequently, the amount of toughness improvement must be balanced between interlaminar and intralaminar fracture toughness. Finally, this work has demonstrated that even though the multilayer structured laminates provide Mode II interlaminar fracture toughness improvements, their mechanical testing behavior is extremely different than conventional composite structures.

  20. Carbide Coatings for Nickel Alloys, Graphite and Carbon/Carbon Composites to be used in Fluoride Salt Valves

    Energy Technology Data Exchange (ETDEWEB)

    Nagle, Denis [Johns Hopkins Univ., Baltimore, MD (United States); Zhang, Dajie [Johns Hopkins Univ., Baltimore, MD (United States)

    2015-10-22

    The focus of this research was concerned with developing materials technology that supports the evolution of Generation IV Advanced High Temperature Reactor (AHTR) concepts. Specifically, we investigate refractory carbide coatings for 1) nickel alloys, and 2) commercial carbon-carbon composites (CCCs). Numerous compelling reasons have driven us to focus on carbon and carbide materials. First, unlike metals, the strength and modulus of CCCs increase with rising temperature. Secondly, graphite and carbon composites have been proven effective for resisting highly corrosive fluoride melts such as molten cryolite [Na₃AlF₆] at ~1000°C in aluminum reduction cells. Thirdly, graphite and carbide materials exhibit extraordinary radiation damage tolerance and stability up to 2000°C. Finally, carbides are thermodynamically more stable in liquid fluoride salt than the corresponding metals (i.e. Cr and Zr) found in nickel based alloys.

  1. Synthesis of hydrogen-carbon clathrate material and hydrogen evolution therefrom at moderate temperatures and pressures

    Science.gov (United States)

    Lueking, Angela; Narayanan, Deepa

    2011-03-08

    A process for making a hydrogenated carbon material is provided which includes forming a mixture of a carbon source, particularly a carbonaceous material, and a hydrogen source. The mixture is reacted under reaction conditions such that hydrogen is generated and/or released from the hydrogen source, an amorphous diamond-like carbon is formed, and at least a portion of the generated and/or released hydrogen associates with the amorphous diamond-like carbon, thereby forming a hydrogenated carbon material. A hydrogenated carbon material including a hydrogen carbon clathrate is characterized by evolution of molecular hydrogen at room temperature at atmospheric pressure in particular embodiments of methods and compositions according to the present invention.

  2. Compression Testing of Textile Composite Materials

    Science.gov (United States)

    Masters, John E.

    1996-01-01

    The applicability of existing test methods, which were developed primarily for laminates made of unidirectional prepreg tape, to textile composites is an area of concern. The issue is whether the values measured for the 2-D and 3-D braided, woven, stitched, and knit materials are accurate representations of the true material response. This report provides a review of efforts to establish a compression test method for textile reinforced composite materials. Experimental data have been gathered from several sources and evaluated to assess the effectiveness of a variety of test methods. The effectiveness of the individual test methods to measure the material's modulus and strength is determined. Data are presented for 2-D triaxial braided, 3-D woven, and stitched graphite/epoxy material. However, the determination of a recommended test method and specimen dimensions is based, primarily, on experimental results obtained by the Boeing Defense and Space Group for 2-D triaxially braided materials. They evaluated seven test methods: NASA Short Block, Modified IITRI, Boeing Open Hole Compression, Zabora Compression, Boeing Compression after Impact, NASA ST-4, and a Sandwich Column Test.

  3. Formation of a Composite Based on Polyurethane with Carbon Nanotubes and Shungite

    Science.gov (United States)

    Komarov, F. F.; Krivosheev, R. M.; Ksenofontov, M. A.; Koltunovich, T.; Abdullin, Kh. A.; Ostrovskaya, L. E.; Togambaeva, A. K.

    2015-03-01

    Physicomechanical and electrophysical characteristics of a polyurethane composite doped with carbon-containing materials have been investigated. It has been found that the roughness of the sample's surface and also the porosity increase with the concentration of the dopant. Volt-ampere characteristics of composite materials point to the activated type of conductivity in these materials; however, at a temperature of nearly 340 K, the type of conductivity is changed. Also, the frequency dependence of the conductivity has been established.

  4. Carbon Nanotubes Filled with Ferromagnetic Materials

    Directory of Open Access Journals (Sweden)

    Albrecht Leonhardt

    2010-08-01

    Full Text Available Carbon nanotubes (CNT filled with ferromagnetic metals like iron, cobalt or nickel are new and very interesting nanostructured materials with a number of unique properties. In this paper we give an overview about different chemical vapor deposition (CVD methods for their synthesis and discuss the influence of selected growth parameters. In addition we evaluate possible growth mechanisms involved in their formation. Moreover we show their identified structural and magnetic properties. On the basis of these properties we present different application possibilities. Some selected examples reveal the high potential of these materials in the field of medicine and nanotechnology.

  5. Preparation and Properties of Carbon Fiber Chiral Materials

    Institute of Scientific and Technical Information of China (English)

    ZHANG Ping; HUANG Zhixin; WANG Guoqing

    2008-01-01

    The chiral materials were prepared by using the carbon fiber helices as chiral inclusions,and the composite of Fe3O4 and polyaniline as matrix.The electromagnetic properties,including the rotation angles,the axial ratios and the complex chirality parameters,were measured by using a circular waveguide method in the 8.5-11.0 GHz frequency range.The dependence of these electromagnetic properties on the frequency and the concentration of the Fe3O4 in the composite matrix were analyzed.The results show that an appropriate concentration of Fe3O4 in the matrix is useful in improving the electromagnetic properties of the chiral material.

  6. Aligning carbon fibers in micro-extruded composite ink

    Science.gov (United States)

    Mahajan, Chaitanya G.

    Direct write processes include a wide range of additive manufacturing techniques with the ability to fabricate structures directly onto planar and non-planar surfaces. Most additive manufacturing techniques use unreinforced polymers to produce parts. By adding carbon fiber as a reinforcing material, properties such as mechanical strength, electrical conductivity, and thermal conductivity can be enhanced. Carbon fibers can be long and continuous, or short and discontinuous. The strength of carbon fiber composite parts is greatly increased when the fibers are preferentially aligned. This research focuses on increasing the strength of additively manufactured parts reinforced using discontinuous carbon fibers that have been aligned during the micro extrusion process. A design of experiments (DOE) approach was used to identify significant process parameters affecting fiber alignment. Factors such as the length of carbon fibers, nozzle diameter, fiber loading fraction, air pressure, translational speed and standoff distance were considered. A two dimensional Fast Fourier Transform (2D FFT) was used to quantify the degree of fiber alignment in the extruded composite inks. ImageJ software supported by an oval profile plugin was used with micrographs of printed samples to obtain the carbon fiber alignment values. The optimal value for the factors was derived by identifying the significant main and interaction effects. Based on the results of the DOE, tensile test samples were printed with fibers aligned parallel and perpendicular to the tensile axis. A standard test method for tensile properties of plastic revealed that the extruded parts with fibers aligned along the tensile axis were better in tensile strength and modulus.

  7. Manufacturing of Nanocomposite Carbon Fibers and Composite Cylinders

    Science.gov (United States)

    Tan, Seng; Zhou, Jian-guo

    2013-01-01

    Pitch-based nanocomposite carbon fibers were prepared with various percentages of carbon nanofibers (CNFs), and the fibers were used for manufacturing composite structures. Experimental results show that these nanocomposite carbon fibers exhibit improved structural and electrical conductivity properties as compared to unreinforced carbon fibers. Composite panels fabricated from these nanocomposite carbon fibers and an epoxy system also show the same properties transformed from the fibers. Single-fiber testing per ASTM C1557 standard indicates that the nanocomposite carbon fiber has a tensile modulus of 110% higher, and a tensile strength 17.7% times higher, than the conventional carbon fiber manufactured from pitch. Also, the electrical resistance of the carbon fiber carbonized at 900 C was reduced from 4.8 to 2.2 ohm/cm. The manufacturing of the nanocomposite carbon fiber was based on an extrusion, non-solvent process. The precursor fibers were then carbonized and graphitized. The resultant fibers are continuous.

  8. 碳纤维/单分子环氧树脂基复合材料的研究%STUDY ON THE CARBON FIBER/UNIMOLECULE EPOXY COMPOSITE MATERIALS

    Institute of Scientific and Technical Information of China (English)

    杨海波; 芦艾; 李艳; 孙素明

    2012-01-01

    Took the excellent liquidity unimolecule epoxy 4,5-epoxyclyclohexyl-l ,2-diglycidyl diformate as the matrix resin, methyl hexahydrophthalic anhydride as the curing agent, benzyldimethylamine as the accelerator, the paper initially researched chemical feature of the rheology of the cure reaction and gained the essential curing process. Then took the T700S carbon fiber tabby fabrics as the reinforcing material, the paper made an epoxy/car-bon fiber composite laminate material with the thickness of 2mm. Experimental results show that, through the soak of the diluent, the mass contents of CF in the composite can be more than 70%. Without the diluent, the mass contents of CF can be 64%. The tensile strength and the flexural strength of the composite are 916MPa and 103MPa, the glass transition temperature is177℃.%以流动性优异的单分子环氧树脂4,5-环氧环己烷-1,2-二甲酸二缩水甘油酯为基体树脂,甲基六氢邻苯二甲酸酐为固化剂,苄基二甲胺为促进剂,初步研究了其固化反应的化学流变特性,获得了基本的固化工艺.然后以T700S碳纤维平纹织物为增强材料,制备了2mm厚度的环氧/碳纤维复合材料层压板材.试验结果表明,通过稀释剂浸渍,复合材料中的CF质量分数可以达到70%以上.在完全无稀释剂时,CF的质量分数可以达到64%.复合材料的最高拉伸强度和弯曲强度分别为916MPa和1031MPa.其玻璃化转变温度为177℃.

  9. Defect analysis in drilling needle-punched carbon–carbon composites perpendicular to nonwoven fabrics

    Directory of Open Access Journals (Sweden)

    Chenwei Shan

    2015-08-01

    Full Text Available Carbon–carbon composites are unique materials consisting of carbon fibers embedded in a carbonaceous matrix. Drilling of carbon–carbon composites is difficult to carry out due to the anisotropic, high specific stiffness and brittleness, nonhomogeneous inner structure of composites, and high abrasiveness of their reinforcing constituents. These typically result in defects being introduced into the workpiece and in very rapid wear development in the drilling tool. Defects are the undesired effects of machining using nonappropriate drilling parameters or worn drill. Aimed at this issue, first, the major defects caused in drilling needle-punched carbon–carbon composites are analyzed in detail. Second, the fiber fuzz factor and the ripping factor of fibers are defined to depict the drilling defects. Experiments are carried out using a conventional twist drill, and the results indicate that material structures, federates, and cutting speeds are reckoned to be the most significant factors contributing to defects.

  10. Shockwave response of two carbon fiber-polymer composites to 50 GPa

    Science.gov (United States)

    Dattelbaum, Dana M.; Coe, Joshua D.; Rigg, Paulo A.; Scharff, R. Jason; Gammel, J. Tinka

    2014-11-01

    Shock compression of two molded, carbon fiber-filled polymer composites was performed in gas gun-driven plate impact experiments at impact velocities up to ≈5 km/s. Hugoniot states for both composites were obtained from chopped carbon fibers, bound by either phenolic or cyanate ester polymeric resins. Their dynamic responses were similar, although the 10 wt. % difference of carbon fill produced measureable divergence in shock compressibility. The chopped carbon fibers in the polymer matrix led to moderately anisotropic shocks, particularly when compared with the more commonly encountered filament-wound carbon fiber-epoxy composites. A discontinuity, or cusp, was observed in the principal Hugoniot of both materials near 25 GPa. We attribute the accompanying volume collapse to shock-driven chemical decomposition above this condition. Inert and reacted products equations of state were used to capture the response of the two materials below and above the cusp.

  11. The Cost of Automotive Polymer Composites: A Review and Assessment of DOE's Lightweight Materials Composites Research

    Energy Technology Data Exchange (ETDEWEB)

    Das, S.

    2001-01-26

    Polymer composite materials have been a part of the automotive industry for several decades, with early application in the 1953 Corvette. These materials have been used for applications with low production volumes, because of their shortened lead times and lower investment costs relative to conventional steel fabrication. Important drivers of the growth of polymer composites have been the reduced weight and parts consolidation opportunities the material offers, as well as design flexibility, corrosion resistance, material anisotropy, and mechanical properties. Although these benefits are well recognized by the industry, polymer composite use has been dampened by high material costs, slow production rates, and to a lesser extent, concerns about recyclability. Also impeding large scale automotive applications is a curious mixture of concerns about material issues such as crash energy absorption, recycling challenges, competitive and cost pressures, the industry's general lack of experience and comfort with the material, and industry concerns about its own capabilities (Flynn and Belzowski 1995). Polymer composite materials are generally made of two or more material components--fibers, either glass or carbon, reinforced in the matrix of thermoset or thermoplastic polymer materials. The glass-reinforced thermoset composites are the most commonly used composite in automotive applications today, but thermoplastic composites and carbon fiber-reinforced thermosets also hold potential. It has been estimated that significant use of glass-reinforced polymers as structural components could yield a 20-35% reduction in vehicle weight. More importantly, the use of carbon fiber-reinforced materials could yield a 40-65% reduction in weight.

  12. Mesoporous carbon nitride-tungsten oxide composites for enhanced photocatalytic hydrogen evolution.

    Science.gov (United States)

    Kailasam, Kamalakannan; Fischer, Anna; Zhang, Guigang; Zhang, Jinshui; Schwarze, Michael; Schröder, Marc; Wang, Xinchen; Schomäcker, Reinhard; Thomas, Arne

    2015-04-24

    Composites of mesoporous polymeric carbon nitride and tungsten(VI) oxide show very high photocatalytic activity for the evolution of hydrogen from water under visible light and in the presence of sacrificial electron donors. Already addition of very small amounts of WO3 yields up to a twofold increase in the efficiency when compared to bulk carbon nitrides and their composites and more notably even to the best reported mesoporous carbon nitride-based photocatalytic materials. The higher activity can be attributed to the high surface area and synergetic effect of the carbon nitrides and the WO3 resulting in improved charge separation through a photocatalytic solid-state Z-scheme mechanism.

  13. Influence of Carbon & Glass Fiber Reinforcements on Flexural Strength of Epoxy Matrix Polymer Hybrid Composites

    Directory of Open Access Journals (Sweden)

    T.D. Jagannatha

    2015-04-01

    Full Text Available Hybrid composite materials are more attracted by the engineers because of their properties like stiffness and high specific strength which leads to the potential application in the area of aerospace, marine and automobile sectors. In the present investigation, the flexural strength and flexural modulus of carbon and glass fibers reinforced epoxy hybrid composites were studied. The vacuum bagging technique was adopted for the fabrication of polymer hybrid composite materials. The hardness, flexural strength and flexural modulus of the hybrid composites were determined as per ASTM standards. The hardness, flexural strength and flexural modulus were improved as the fiber reinforcement contents increased in the epoxy matrix material.

  14. Stratospheric experiments on curing of composite materials

    Science.gov (United States)

    Chudinov, Viacheslav; Kondyurin, Alexey; Svistkov, Alexander L.; Efremov, Denis; Demin, Anton; Terpugov, Viktor; Rusakov, Sergey

    2016-07-01

    Future space exploration requires a large light-weight structure for habitats, greenhouses, space bases, space factories and other constructions. A new approach enabling large-size constructions in space relies on the use of the technology of polymerization of fiber-filled composites with a curable polymer matrix applied in the free space environment on Erath orbit. In orbit, the material is exposed to high vacuum, dramatic temperature changes, plasma of free space due to cosmic rays, sun irradiation and atomic oxygen (in low Earth orbit), micrometeorite fluence, electric charging and microgravitation. The development of appropriate polymer matrix composites requires an understanding of the chemical processes of polymer matrix curing under the specific free space conditions to be encountered. The goal of the stratospheric flight experiment is an investigation of the effect of the stratospheric conditions on the uncured polymer matrix of the composite material. The unique combination of low residual pressure, high intensity UV radiation including short-wave UV component, cosmic rays and other aspects associated with solar irradiation strongly influences the chemical processes in polymeric materials. We have done the stratospheric flight experiments with uncured composites (prepreg). A balloon with payload equipped with heater, temperature/pressure/irradiation sensors, microprocessor, carrying the samples of uncured prepreg has been launched to stratosphere of 25-30 km altitude. After the flight, the samples have been tested with FTIR, gel-fraction, tensile test and DMA. The effect of cosmic radiation has been observed. The composite was successfully cured during the stratospheric flight. The study was supported by RFBR grants 12-08-00970 and 14-08-96011.

  15. The dynamic response of carbon fiber-filled polymer composites

    OpenAIRE

    Patterson B.; Orler E.B.; Furmanski J.; Rigg P.A.; Scharff R.J.; Stahl D.B.; Sheffield S.A.; Gustavsen R.L.; Dattelbaum D.M.; Coe J.D.

    2012-01-01

    The dynamic (shock) responses of two carbon fiber-filled polymer composites have been quantified using gas gun-driven plate impact experimentation. The first composite is a filament-wound, highly unidirectional carbon fiber-filled epoxy with a high degree of porosity. The second composite is a chopped carbon fiber- and graphite-filled phenolic resin with little-to-no porosity. Hugoniot data are presented for the carbon fiber-epoxy (CE) composite to 18.6 GPa in the through-thickness direction,...

  16. Photophysics of Carbon Nanotubes Interfaced with Organic and Inorganic Materials

    CERN Document Server

    Levitsky, Igor A; Karachevtsev, Victor A

    2012-01-01

    Photophysics of Carbon Nanotubes Interfaced with Organic and Inorganic Materials describes physical, optical and spectroscopic properties of the emerging class of nanocomposites formed from carbon nanotubes (CNTs)  interfacing with organic and inorganic materials. The three main chapters detail novel trends in  photophysics related to the interaction of  light with various carbon nanotube composites from relatively simple CNT/small molecule assemblies to complex hybrids such as CNT/Si and CNT/DNA nanostructures.   The latest experimental results are followed up with detailed discussions and scientific and technological perspectives to provide a through coverage of major topics including: ·   Light harvesting, energy conversion, photoinduced charge separation  and transport  in CNT based nanohybrids · CNT/polymer composites exhibiting photoactuation; and ·         Optical  spectroscopy  and structure of CNT/DNA complexes. Including original data and a short review of recent research, Phot...

  17. Composite materials and bodies including silicon carbide and titanium diboride and methods of forming same

    Science.gov (United States)

    Lillo, Thomas M.; Chu, Henry S.; Harrison, William M.; Bailey, Derek

    2013-01-22

    Methods of forming composite materials include coating particles of titanium dioxide with a substance including boron (e.g., boron carbide) and a substance including carbon, and reacting the titanium dioxide with the substance including boron and the substance including carbon to form titanium diboride. The methods may be used to form ceramic composite bodies and materials, such as, for example, a ceramic composite body or material including silicon carbide and titanium diboride. Such bodies and materials may be used as armor bodies and armor materials. Such methods may include forming a green body and sintering the green body to a desirable final density. Green bodies formed in accordance with such methods may include particles comprising titanium dioxide and a coating at least partially covering exterior surfaces thereof, the coating comprising a substance including boron (e.g., boron carbide) and a substance including carbon.

  18. Contraction stresses of composite resin filling materials.

    Science.gov (United States)

    Hegdahl, T; Gjerdet, N R

    1977-01-01

    The polymerization shrinkage of composite resin filling materials and the tensile stresses developed when the shrinkage is restrained were measured in an in vitro experiment. This allows an estimation to be made of the forces exerted upon the enamel walls of cavities filled with the resin in the acid etch technique. The results indicate that the stresses acting on the enamel are low compared to the tensile strength of the enamel.

  19. The effect of the reinforcing carbon on the microstructure of pitch-based granular composites.

    Science.gov (United States)

    Méndez, A; Santamaría, R; Granda, M; Menéndez, R

    2003-02-01

    Carbon composites were prepared with four pitches (a commercial impregnating coal-tar pitch, two thermally treated pitches and an air-blown pitch) and four granular carbons (anthracite, graphite, green petroleum coke and foundry coke). Granular carbon/pitch proportions were optimized for each composite and differed in the characteristics of the single components. Interactions of the pitch with the granular carbons during pyrolysis and their subsequent effects on the microstructure of the final composite were monitored by light microscopy. The results show that the light texture of the matrix and the porosity of the composite depend not only on the chemical composition of the pitch but also on the specific granular carbon used as reinforcing material. The same pitch may generate different light textures depending on the characteristics of the carbon. Composites from thermally treated pitches and graphite show highly ordered matrices orientated in the direction of graphite planes. Graphite particles seem to exert a huge influence on mesophase development during the pyrolysis of the treated pitches, affecting not only the orientation of the mesophase, but also reducing the rate of mesophase formation. On the other hand, when green petroleum coke is used with the thermally treated pitches, matrices show a small size light texture, due to the high reactivity of the pitch in the presence of this granular carbon. The porosity of the composites is controlled by both the pitch and the granular carbon.

  20. An Overview of Recent Development in Composite Catalysts from Porous Materials for Various Reactions and Processes

    Directory of Open Access Journals (Sweden)

    Zaiku Xie

    2010-05-01

    Full Text Available Catalysts are important to the chemical industry and environmental remediation due to their effective conversion of one chemical into another. Among them, composite catalysts have attracted continuous attention during the past decades. Nowadays, composite catalysts are being used more and more to meet the practical catalytic performance requirements in the chemical industry of high activity, high selectivity and good stability. In this paper, we reviewed our recent work on development of composite catalysts, mainly focusing on the composite catalysts obtained from porous materials such as zeolites, mesoporous materials, carbon nanotubes (CNT, etc. Six types of porous composite catalysts are discussed, including amorphous oxide modified zeolite composite catalysts, zeolite composites prepared by co-crystallization or overgrowth, hierarchical porous catalysts, host-guest porous composites, inorganic and organic mesoporous composite catalysts, and polymer/CNT composite catalysts.

  1. Synthesis and application of multi-walled carbon nanotubes-molecularly imprinted sol-gel composite material for on-line solid-phase extraction and high-performance liquid chromatography determination of trace Sudan IV

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Zhaohui, E-mail: zhaohuizhang77@hotmail.com [College of Chemistry and Chemical Engineering, Jishou University, Jishou 416000 (China); State Key Laboratory of Chemo/Biosensing and Chemometrics, Hunan University, Changsha 410082 (China); Zhang Huabin; Hu Yufang [College of Chemistry and Chemical Engineering, Jishou University, Jishou 416000 (China); Yao Shouzhuo [State Key Laboratory of Chemo/Biosensing and Chemometrics, Hunan University, Changsha 410082 (China)

    2010-02-28

    A novel composite material of multi-walled carbon nanotubes (MWNTs)-Sudan IV molecularly imprinted polymers (MIPs) was prepared by surface molecular imprinting technique in combination with sol-gel technology. The MWNTs-MIPs were evaluated by scanning electron micrograph (SEM), Fourier transform infrared spectroscopy (FT-IR), and adsorption experiments. The results showed that the MWNTs-MIPs exhibited good selective recognition to Sudan IV. The maximum saturated binding capacity (Q{sub max}) is 63.2 {mu}mol g{sup -1}. Applied as sorbent, the MWNTs-MIPs were used for the determination of trace Sudan IV in chilli powder by on-line solid-phase extraction-high-performance liquid chromatography (SPE-HPLC). The results showed that an enrichment factor of 741 was achieved with a loading flow rate of 1.0 mL min{sup -1} for sampling 50 mL. The MWNTs-MIPs provided a fast and convenience determination platform for Sudan IV in real samples.

  2. The correlation between carbon structures and electrochemical properties of sulfur/carbon composites for Li-S batteries

    Science.gov (United States)

    Du, Zhenzhen; Xu, Jin; Jin, Song; Shi, Yuchen; Guo, Chengkun; Kong, Xianghua; Zhu, Yanwu; Ji, Hengxing

    2017-02-01

    The structures of carbon materials greatly affect the electrochemical properties of sulfur/carbon composites for lithium-sulfur (Li-S) batteries. Understanding the effect of carbon structure factors on the electrochemical properties of sulfur/carbon composites helps in rational designing of the cathode material for optimized battery performance. We prepare reduced graphene oxide (RGO), cysteine-modified RGO (RGO-CYS), microwave-expanded graphite oxide (MEGO) and activated-MEGO (aMEGO) with specific surface areas (SSA) of 58-3010 m2 g-1, C/O atomic ratios of 2.41-10.81, pore sizes of 0.9-5.6 nm and pore volumes of 0.14-2.03 cm3 g-1. The electrochemical performance researches S/RGO-CYS > S/RGO > S/MEGO > S/aMEGO when it is listed in the order of their specific capacity, rate capability and cyclic life. And the S/RGO-CYS delivers a high reversible capacity of 455 mA h g-1 at 8 C. The excellent performance of S/RGO-CYS composite is ascribed to the sulfur-containing functional groups of the RGO-CYS, which helps the sulfur dispersion and stabilizes the dissoluble lithium polysulfides. Our results demonstrate that the surface chemistry of carbon materials plays a more important role than the SSA, pore size and pore volume for the electrochemical properties of sulfur/carbon composites for Li-S batteries.

  3. Chlorhexidine-releasing methacrylate dental composite materials.

    Science.gov (United States)

    Leung, Danny; Spratt, David A; Pratten, Jonathan; Gulabivala, Kishor; Mordan, Nicola J; Young, Anne M

    2005-12-01

    Light curable antibacterial, dental composite restoration materials, consisting of 80 wt% of a strontium fluoroaluminosilicate glass dispersed in methacrylate monomers have been produced. The monomers contained 40-100 wt% of a 10 wt% chlorhexidine diacetate (CHXA) in hydroxyethylmethacrylate (HEMA) solution and 60-0 wt% of a 50/50 mix of urethane dimethacrylate (UDMA) and triethyleneglycol dimethacrylate (TEGDMA). On raising HEMA content, light cure polymerisation rates decreased. Conversely, water sorption induced swelling and rates of diffusion controlled CHXA release from the set materials increased. Experimental composites with 50 and 90 wt% of the CHXA in HEMA solution in the monomer were shown, within a constant depth film fermentor (CDFF), to have slower rates of biofilm growth on their surfaces between 1 and 7 days than the commercial dental composite Z250 or fluoride-releasing dental cements, Fuji II LC and Fuji IX. When an excavated bovine dentine cylinder re-filled with Z250 was placed for 10 weeks in the CDFF, both bacteria and polymers from the artificial saliva penetrated between the material and dentine. With the 50 wt% experimental HEMA/CHXA formulation, this bacterial microleakage was substantially reduced. Polymer leakage, however, still occurred. Both polymer and bacterial microleakage were prevented with a 90 wt% HEMA/CHXA restoration in the bovine dentine due to swelling compensation for polymerisation shrinkage in combination with antibacterial release.

  4. Repairable Woven Carbon Fiber Composites with Full Recyclability Enabled by Malleable Polyimine Networks.

    Science.gov (United States)

    Taynton, Philip; Ni, Huagang; Zhu, Chengpu; Yu, Kai; Loob, Samuel; Jin, Yinghua; Qi, H Jerry; Zhang, Wei

    2016-04-20

    Carbon-fiber reinforced composites are prepared using catalyst-free malleable polyimine networks as binders. An energy neutral closed-loop recycling process has been developed, enabling recovery of 100% of the imine components and carbon fibers in their original form. Polyimine films made using >21% recycled content exhibit no loss of mechanical performance, therefore indicating all of the thermoset composite material can be recycled and reused for the same purpose.

  5. Processing, structure and flexural strength of CNT and carbon fibre reinforced, epoxy-matrix hybrid composite

    Indian Academy of Sciences (India)

    K Chandra Shekar; M Sai Priya; P K Subramanian; Anil Kumar; B Anjaneya Prasad; N Eswara Prasad

    2014-05-01

    Advanced materials such as continuous fibre-reinforced polymer matrix composites offer significant enhancements in variety of properties, as compared to their bulk, monolithic counterparts. These properties include primarily the tensile stress, flexural stress and fracture parameters. However, till date, there are hardly any scientific studies reported on carbon fibre (Cf) and carbon nanotube (CNT) reinforced hybrid epoxy matrix composites (unidirectional). The present work is an attempt to bring out the flexural strength properties along with a detailed investigation in the synthesis of reinforced hybrid composite. In this present study, the importance of alignment of fibre is comprehensively evaluated and reported. The results obtained are discussed in terms of material characteristics, microstructure and mode of failure under flexural (3-point bend) loading. The study reveals the material exhibiting exceptionally high strength values and declaring itself as a material with high strength to weight ratio when compared to other competing polymer matrix composites (PMCs); as a novel structural material for aeronautical and aerospace applications.

  6. Properties and application of carbon composite brick for blast furnace hearth

    Directory of Open Access Journals (Sweden)

    Jiao K.X.

    2015-01-01

    Full Text Available A type of carbon composite brick was produced via the microporous technique using natural flack graphite, α-Al2O3 and high-quality bauxite chamotte (Al2O3≥87 mass% as raw materials with fine silicon powder as additive. The composition and microstructure of the obtained carbon composite were characterized using chemical analysis, XRD and SEM with EDS. The high temperature properties of thermal conductivity, oxidization and corrosion by molten slag and hot metal of the composite were analyzed. Based on these, the type of carbon composite brick worked in a blast furnace hearth for six years was further sampled at different positions. The protective layer was found and its chemical composition and microscopic morphology were investigated. It is found that the carbon composite brick combines the good properties of both the conventional carbon block and ceramic cup refractory. The protective layer near the hot face consists of two separated sublayers, i.e. the slag layer and the carbon layer. A certain amount of slag phase is contained in the carbon layer, which is caused by the reaction of coke ash with the refractory. No obvious change in the chemical composition of the protective layer along the depth of the sidewall is found. This work provides a useful guidance for the extension of the lifetime of blast furnace hearths.

  7. Effects of Atomic-Scale Structure on the Fracture Properties of Amorphous Carbon - Carbon Nanotube Composites

    Science.gov (United States)

    Jensen, Benjamin D.; Wise, Kristopher E.; Odegard, Gregory M.

    2015-01-01

    The fracture of carbon materials is a complex process, the understanding of which is critical to the development of next generation high performance materials. While quantum mechanical (QM) calculations are the most accurate way to model fracture, the fracture behavior of many carbon-based composite engineering materials, such as carbon nanotube (CNT) composites, is a multi-scale process that occurs on time and length scales beyond the practical limitations of QM methods. The Reax Force Field (ReaxFF) is capable of predicting mechanical properties involving strong deformation, bond breaking and bond formation in the classical molecular dynamics framework. This has been achieved by adding to the potential energy function a bond-order term that varies continuously with distance. The use of an empirical bond order potential, such as ReaxFF, enables the simulation of failure in molecular systems that are several orders of magnitude larger than would be possible in QM techniques. In this work, the fracture behavior of an amorphous carbon (AC) matrix reinforced with CNTs was modeled using molecular dynamics with the ReaxFF reactive forcefield. Care was taken to select the appropriate simulation parameters, which can be different from those required when using traditional fixed-bond force fields. The effect of CNT arrangement was investigated with three systems: a single-wall nanotube (SWNT) array, a multi-wall nanotube (MWNT) array, and a SWNT bundle system. For each arrangement, covalent bonds are added between the CNTs and AC, with crosslink fractions ranging from 0-25% of the interfacial CNT atoms. The SWNT and MWNT array systems represent ideal cases with evenly spaced CNTs; the SWNT bundle system represents a more realistic case because, in practice, van der Waals interactions lead to the agglomeration of CNTs into bundles. The simulation results will serve as guidance in setting experimental processing conditions to optimize the mechanical properties of CNT

  8. Properties of glass/carbon fiber reinforced epoxy hybrid polymer composites

    Science.gov (United States)

    Patel, R. H.; Sevkani, V. R.; Patel, B. R.; Patel, V. B.

    2016-05-01

    Composite Materials are well known for their tailor-made properties. For the fabrication of composites different types of reinforcements are used for different applications. Sometimes for a particular application, one type of reinforcement may not fulfill the requirements. Therefore, more than one type of reinforcements may be used. Thus, the idea of hybrid composites arises. Hybrid composites are made by joining two or more different reinforcements with suitable matrix system. It helps to improve the properties of composite materials. In the present work glass/carbon fiber reinforcement have been used with a matrix triglycidyl ether of tris(m-hydroxy phenyl) phosphate epoxy resin using amine curing agent. Different physical and mechanical properties of the glass, carbon and glass/carbon fiber reinforced polymeric systems have been found out.

  9. Computerized calculation of material balances in carbonization

    Energy Technology Data Exchange (ETDEWEB)

    Chistyakov, A.M.

    1980-09-01

    Charge formulations and carbonisation schedules are described by empirical formulae used to calculate the yield of coking products. An algorithm is proposed for calculating the material balance, and associated computer program. The program can be written in conventional languages, e.g. Fortran, Algol etc. The information obtained can be used for on-line assessment of the effects of charge composition and properties on the coke and by-products yields, as well as the effects of the carbonisation conditions.

  10. Thermophysical Properties of Cool Storage of Paraffin-based Composite Phase Change Materials Filled with Carbon Nanotubes%石蜡基碳纳米管复合相变蓄冷材料的热性能研究

    Institute of Scientific and Technical Information of China (English)

    陈杨华; 李钰; 郭文帅; 陈非凡; 陈姮

    2014-01-01

    To address thermal conductivity of paraffin wax ( PW), carbon nanotubes ( CNTs) were mixed with PW to form PW-CNTs composites. PW-CNTs composites has been prepared with various mass fractions (1% 、2%、5%) of carbon nanotubes. The thermal prop-erties including phase transition temperature, latent heat of phase change, thermal conductivity and thermal stability during the phase change process are investigated. The phase change property was characterized using differential scanning calorimeter( DSC) and the ther-mal conductivity was measured by using transient hot wire method. The results show that with the increasing of mass fraction of CNTs, ther-mal conductivity become larger, and the latent heat decrease gradually. Phase transition temperature of PW-5CNTs is 4-8 ℃, latent heat of phase change is 137. 6-142. 7 kJ/kg, thermal conductivity is 0. 28 W/(m�K)(liquid), and PW-5CNTs have good enough stability to be widely used as cool storage materials.%针对石蜡导热系数低,传热性能差的缺点,采用向其中添加碳纳米管来改善其导热性能。实验制备了碳纳米管质量分数为1%、2%和5%的石蜡基复合相变材料,通过差示扫描量热仪和热传导系数仪研究了复合材料的相变性能,导热性能和稳定性。实验结果表明,随着碳纳米管质量分数的增加,复合材料的导热系数逐渐增大,相变焓有所减小。质量分数为5%的石蜡基碳纳米管复合材料相变温度为4~8℃,相变焓为137�6~142�7 kJ/kg,比纯石蜡下降了约18%,液态导热系数为0�28 W/( m�K),比纯石蜡提高了40%,稳定性较好,可作为蓄冷材料广泛应用于蓄冷系统。

  11. Flexible strain sensor based on carbon nanotube rubber composites

    Science.gov (United States)

    Kim, Jin-Ho; Kim, Young-Ju; Baek, Woon Kyung; Lim, Kwon Taek; Kang, Inpil

    2010-04-01

    Electrically conducting rubber composites (CRC) with carbon nanotubes (CNTs) filler have received much attention as potential materials for sensors. In this work, Ethylene propylene diene M-class rubber (EPDM)/CNT composites as a novel nano sensory material were prepared to develop flexible strain sensors that can measure large deformation of flexible structures. The EPDM/CNT composites were prepared by using a Brabender mixer with multi-walled CNTs and organo-clay. A strain sensor made of EPDM/CNT composite was attached to the surface of a flexible beam and change of resistance of the strain sensor was measured with respect to the beam deflection. Resistance of the sensor was change quite linearly under the bending and compressive large beam deflection. Upon external forces, CRC deformation takes place with the micro scale change of inter-electrical condition in rubber matrix due to the change of contact resistance, and CRC reveals macro scale piezoresistivity. It is anticipated that the CNT/EPDM fibrous strain sensor can be eligible to develop a biomimetic artificial neuron that can continuously sense deformation, pressure and shear force.

  12. The development of high precision carbon fiber composite mirror

    Science.gov (United States)

    Xu, Liang; Ding, Jiao-teng; Wang, Yong-jie; Xie, Yong-jie; Ma, Zhen; Fan, Xue-wu

    2016-10-01

    Due to low density, high stiffness, low thermal expansion coefficient, duplicate molding, etc., carbon fiber reinforced polymer (CFRP) is one of the potential materials of the optical mirror. The process developed for Φ300mm high precision CFRP mirror described in this paper. A placement tool used to improve laying accuracy up to ± 0.1°.A special reinforced cell structure designed to increase rigidity and thermal stability. Optical replication process adopted for surface modification of the carbon fiber composite mirror blank. Finally, surface accuracy RMS of Φ300mm CFRP mirror is 0.22μm, surface roughness Ra is about 2nm, and the thermal stability can achieve 13nm /°C from the test result. The research content is of some reference value in the infrared as well as visible light applications.

  13. Materials design for electrocatalytic carbon capture

    Directory of Open Access Journals (Sweden)

    Xin Tan

    2016-05-01

    Full Text Available We discuss our philosophy for implementation of the Materials Genome Initiative through an integrated materials design strategy, exemplified here in the context of electrocatalytic capture and separation of CO2 gas. We identify for a group of 1:1 X–N graphene analogue materials that electro-responsive switchable CO2 binding behavior correlates with a change in the preferred binding site from N to the adjacent X atom as negative charge is introduced into the system. A reconsideration of conductive N-doped graphene yields the discovery that the N-dopant is able to induce electrocatalytic binding of multiple CO2 molecules at the adjacent carbon sites.

  14. Friction and wear properties of pitch/resin densified carbon-carbon composites used for airbrakes

    Institute of Scientific and Technical Information of China (English)

    巩前明; 黄伯云; 黄启忠; 李江鸿; 吴凤秋; 李晔

    2002-01-01

    By use of X-ray diffractometry and scanning electron microscope (SEM), the friction and wear results obtained from MM-1000 dynamometer tests of CVI pitch/resin C/C composites were analyzed. By investigating the factors that affected the friction and wear properties, such as matrix carbon, application environment, graphitization degree and brake pressure, etc, friction and wear mechanism of carbon materials were probed. The results indicate that pitch densified CVI initially treated composite is more graphitizable with its graphitization degree up to 62%, and which results in uniform small debris easier to generate, more smooth friction curves with the coefficient of 0.3~0.4 and relatively higher linear wear and mass loss, compared with CVI/resin C/C composites. It was further proved by SEM observation that tribological behavior of C/C composite was system dependent. Factors determining the friction and wear properties such as the size of debris and its influence on friction and wear, brake pressure, graphization degree and debris film formation interacted and affected each other. The friction and wear mechanism of C/C composites under different high temperature treatments needs further research.

  15. Electroanalysis using modified hierarchical nanoporous carbon materials.

    Science.gov (United States)

    Rodriguez, Rusbel Coneo; Moncada, Angelica Baena; Acevedo, Diego F; Planes, Gabriel A; Miras, Maria C; Barbero, Cesar A

    2013-01-01

    The role of the electrode nanoporosity in electroanalytical processes is discussed and specific phenomena (slow double layer charging, local pH effects) which can be present in porous electrode are described. Hierarchical porous carbon (HPC) materials are synthesized using a hard template method. The three dimensional carbon porosity is examined using scanning electron microscopy on flat surfaces cut using a focused ion beam (FIB-SEM). The electrochemical properties of the HPC are measured using cyclic voltammetry, AC impedance, chronoamperometry and Probe Beam Deflection (PBD) techniques. Chronoamperometry measurements of HPC seems to fit a transmission line model. PBD data show evidence of local pH changes inside the pores, during double layer charging. The HPC are modified by in situ (chemical or electrochemical) formation of metal (Pt/Ru) or metal oxide (CoOx, Fe3O4) nanoparticles. Additionally, HPC loaded with Pt decorated magnetite (Fe3O4) nanoparticles is produced by galvanic displacement. The modified HPC materials are used for the electroanalysis of different substances (CO, O2, AsO3(-3)). The role of the nanoporous carbon substrate in the electroanalytical data is evaluated.

  16. Sub percolation threshold carbon nanotube based polyvinylidene fluoride polymer-polymer composites

    Science.gov (United States)

    Jacob, Cedric Antony

    The study of piezoelectric materials has traditionally focused largely on homogeneous crystalline or semi-crystalline materials. This research focuses on the concept of piezoelectric composites using selective microstructural reinforcement in the piezoelectric material to improve the piezoelectric properties. This is done using a polyvinylidene fluoride (PVDF) and carbon nanotube composite as the model system. A multi-tiered engineering approach is taken to understand the material (experimental and computational analyses) and design a composite system which provides an effective platform for future research in piezoelectric improvement. A finite element analysis is used to evaluate the ability of carbon nanotubes to generate a heterogeneous electric field where local improvements in electric field produce an increase in the effective piezoelectric strength. The study finds that weight percent and aspect ratio of the carbon nanotubes are of key importance while formations of percolating networks are detrimental to performance. This motivates investigation into electrospinning into a method of producing sub percolation threshold composites with large carbon nanotube content. However, the electrospun fabrics have too low of a dielectric strength to sustain high strength electric fields. This is studied within the context of high voltage physics and a solution inspired by traditional composites manufacturing is proposed wherein the electrospun fiber mat is used as the fiber reinforcing component of a polymer-polymer composite. This composite is thoroughly analyzed to show that it allows for a high dielectric strength combined with high carbon nanotube content. It is also shown that the PVDF contains the proper crystal structure to allow for piezoelectric properties. Furthermore, the addition of carbon nanotubes greatly improves the strength and stiffness of the composite, as well as affecting the internal electric field response to an applied voltage. These qualities

  17. Advanced Thermal Protection Systems (ATPS), Aerospace Grade Carbon Bonded Carbon Fiber Material Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Carbon bonded carbon fiber (CBCF) insulating material is the basis for several highly successful NASA developed thermal protection systems (TPS). Among the...

  18. Advanced Thermal Protection Systems (ATPS), Aerospace Grade Carbon Bonded Carbon Fiber Material Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Carbon bonded carbon fiber (CBCF) insulating material is the basis for several highly successful NASA developed thermal protection systems (TPS). Included among...

  19. R&D Directions and Market Development Trend of Carbon Composite Materials%碳纤维复合材料的研发方向和市场开发动向

    Institute of Scientific and Technical Information of China (English)

    罗益锋

    2011-01-01

    The demand of world's PAN-based carbon fiber will reach 50 000 t/a in 2013, which will increase 67% in comparison with 2010, while the demand in 2015 will reach 70 000 t/a, which will expand 2.5 times in comparison with 2010. The patents application amount for carbon fiber composites in 10 years from 2001 up to now will be 1 611, 5 181, 2 510 and 806 respectively for US, Europe, Japan and China mainland. The improvement in formation technologies and development of new products for CFRP were the most active field in this century, while the direction of R&D will surround process improvement in large CRFP wind power blades, the development of serialized parts of electric cars, the improvement of CFRP reinforced technologies and materials for buildings, making varieties for carbon fiber reinforced thermoplastics, and developing of light weight structure airships, etc.%2013年世界PAN基碳纤维的需求将达到577t/a,比2010年增长67%,到2015年可望达到7万t/a,比2010年扩大2.3倍。从2001年至今的10年间,碳纤维复合材料的专利申请量美国约有1611件,欧洲5181件,日本2510件,中国大陆806件。信息表明,CFRP成型技术的改进及其新产品的开发一直是本世纪最活跃的研发领域。而近期的研发方向,重点将围绕大型CFRP风电叶片的工艺改进、电动汽车整车配套部件的研发、CFRP建筑补强技术和材料的改进、碳纤维增强热塑性树脂品种的多样化及轻质结构飞行器的

  20. Characterization and Damage Evaluation of Coal Tar Pitch Carbon Matrix Used in Carbon/Carbon Composites

    Science.gov (United States)

    Bhagat, Atul Ramesh; Mahajan, Puneet

    2016-09-01

    Flexure, compressive, and shear properties of the carbon matrix in carbon/carbon (C/C) composites made via a pitch impregnation method have been determined. The pitch carbon matrix was made using the same densification cycle used in making the C/C composite. Cyclic compression tests were performed on the matrix specimens. While unloading, a reduction in modulus was observed and residual strains were observed on complete unloading. These features were attributed to the presence of damage and plasticity in the densified matrix. A J 2 plasticity model with damage was used to simulate this behavior numerically. The parameters required for plasticity and damage model were evaluated iteratively by comparing the results in experiments with simulation.

  1. A new technology for production of high thickness carbon/carbon composites for launchers application

    Science.gov (United States)

    Albano, Marta; Delfini, Andrea; Pastore, Roberto; Micheli, Davide; Marchetti, Mario

    2016-11-01

    Carbon-Carbon (C/C) composites are known for their extraordinary stability and excellent mechanical properties, almost unchanged at high temperatures. Among the several advanced applications, C/C based materials can be used in engines as nozzle throat section for launchers. In particular, the main feature for such employment is the material high resistance in extreme thermal environment. On the other hand, large-size items are required for this kind of purposes, thus introducing criticalities in terms of material uniformity and final overall properties. Up to now, there no standard for the production of high thickness C/C structures. In this paper a novel manufacturing method is analyzed, following each phase of the process, from the carbon fiber preform design and preparation to the carbon densification by chemical vapor infiltration method. Five preforms of large dimensions with different characteristics have been manufactured and infiltrated. The realized prototypes have been then analyzed by means of mechanical, physical and morphological tests. Aim of the results of this preliminary work is to establish a set of guidelines for a well-defined high thickness C/C production method.

  2. Analysis of discontinuities influence on the differences between static and dynamic elastic modulus of composite materials

    Science.gov (United States)

    Sava, Mihaela; Hadǎr, Anton; Pǎrǎuşanu, Ioan; Petrescu, Horia-Alexandru; Baciu, Florin; Marinel, Stǎnescu Marius

    2016-06-01

    The influence of discontinuities is important for a correct determination of static and dynamic elastic characteristics of the material. In this paper we presented differences arising between the elastic modulus static and dynamic, laminated composite materials reinforced with carbon fiber, aramid and carbon-aramid, depending on the non-uniformity coefficient. For the study were determined static elastic modulus by carrying out traction tests and dynamic elastic modulus by determining the vibration frequency, on specimens of each type of material with and without discontinuities [1]. The elastic properties of composite materials resistance and can be influenced by various defects that arise from technological manufacturing process. This is important for the production of large series of parts of fiber-reinforced composite material, the fibers in the matrix distribution is not uniform. Studies on the mechanical behavior of composites with random distribution of fabrics are made in [2].

  3. Environment Friendly Composite Materials: Biocomposites and Green Composites

    Directory of Open Access Journals (Sweden)

    B. C. Mitra

    2014-05-01

    Full Text Available Biocomposites can supplement and eventually replace petroleum-based composite materials in several applications. Several critical issues related to bio-fiber surface treatments is to make it a more suitable matrix for composite application and promising techniques need to be solved to design biocomposite of interest. The main motivation for developing biocomposites has been and still is to create a new generation of fiber reinforced plastics material competitive with glass fiber reinforced ones which are environmentally compatible in terms of products, use and renewal. There is an immense opportunity in developing new biobased products, but the real challenge isto design suitable bio-based products through innovation ideas. Green materials are the wave of the future. Bionanocomposites have very strong future prospects, though the present low level of production, some deficiency intechnology and high cost restrict them from a wide range of applications.Defence Science Journal, Vol. 64, No. 3, May 2014, pp. 244-261, DOI:http://dx.doi.org/10.14429/dsj.64.7323

  4. Diamond and Carbon Nanotube Composites for Supercapacitor Devices

    Science.gov (United States)

    Moreira, João Vitor Silva; May, Paul William; Corat, Evaldo José; Peterlevitz, Alfredo Carlos; Pinheiro, Romário Araújo; Zanin, Hudson

    2017-02-01

    We report on the synthesis and electrochemical properties of diamond grown onto vertically aligned carbon nanotubes with high surface areas as a template, resulting in a composite material exhibiting high double-layer capacitance as well as low electrochemical impedance electrodes suitable for applications as supercapacitor devices. We contrast results from devices fabricated with samples which differ in both their initial substrates (Si and Ti) and their final diamond coatings, such as boron-doped diamond and diamond-like carbon (DLC). We present for first time a conducting model for non-doped DLC thin-films. All samples were characterized by scanning and transmission electron microscopy and Fourier transform infrared and Raman spectroscopy. Our results show specific capacitance as high as 8.25 F g-1 (˜1 F cm-2) and gravimetric specific energy and power as high as 0.7 W h kg-1 and 176.4 W kg-1, respectively, which suggest that these diamond/carbon nanotube composite electrodes are excellent candidates for supercapacitor fabrication.

  5. Diamond and Carbon Nanotube Composites for Supercapacitor Devices

    Science.gov (United States)

    Moreira, João Vitor Silva; May, Paul William; Corat, Evaldo José; Peterlevitz, Alfredo Carlos; Pinheiro, Romário Araújo; Zanin, Hudson

    2016-10-01

    We report on the synthesis and electrochemical properties of diamond grown onto vertically aligned carbon nanotubes with high surface areas as a template, resulting in a composite material exhibiting high double-layer capacitance as well as low electrochemical impedance electrodes suitable for applications as supercapacitor devices. We contrast results from devices fabricated with samples which differ in both their initial substrates (Si and Ti) and their final diamond coatings, such as boron-doped diamond and diamond-like carbon (DLC). We present for first time a conducting model for non-doped DLC thin-films. All samples were characterized by scanning and transmission electron microscopy and Fourier transform infrared and Raman spectroscopy. Our results show specific capacitance as high as 8.25 F g-1 (˜1 F cm-2) and gravimetric specific energy and power as high as 0.7 W h kg-1 and 176.4 W kg-1, respectively, which suggest that these diamond/carbon nanotube composite electrodes are excellent candidates for supercapacitor fabrication.

  6. Investigation of transient heat transfer in composite walls using carbon/epoxy composites as an example

    Directory of Open Access Journals (Sweden)

    Terpiłowski Janusz

    2015-12-01

    Full Text Available The paper presents the application of similarity theory to investigations of transient heat transfer in materials with complex structure. It describes the theoretical-experimental method for identification and design of the structure of two-component composite walls based on the research of the thermal diffusivity for the composite and its matrix separately. The thermal diffusivity was measured by means of the modified flash method. The method was tested on two samples of double-layer ‘epoxy resin – polyamide’. All the investigated samples had the same diameter of 12 mm and thickness ranging from 1.39–2.60 mm and their equivalent value of thermal diffusivity ranging from (1.21–1.98×10−7 m2/s. Testing the method and research on carbon/epoxy composites was carried out at temperatures close to room temperature.

  7. Carbon fiber CVD coating by carbon nanostructured for space materials protection against atomic oxygen

    Science.gov (United States)

    Pastore, Roberto; Bueno Morles, Ramon; Micheli, Davide

    2016-07-01

    adhesion and durability in the environment. Though these coatings are efficient in protecting polymer composites, their application imposes severe constraints. Their thermal expansion coefficients may differ markedly from those of polymer composite substrates: as a result, cracks develop in the coatings on thermal cycling and AO can penetrate through them to the substrate. In addition to the technicalities of forming an effective barrier, such factors as cost, convenience of application and ease of repair are important considerations in the selection of a coating for a particular application. The latter issues drive the aerospace research toward the development of novel light composite materials, like the so called polymer nanocomposites, which are materials with a polymer matrix and a filler with at least one dimension less than 100 nanometers. Current interest in nanocomposites has been generated and maintained because nanoparticle-filled polymers exhibit unique combinations of properties not achievable with traditional composites. These combinations of properties can be achieved because of the small size of the fillers, the large surface area the fillers provide, and in many cases the unique properties of the fillers themselves. In particular, the carbon fiber-based polymeric composite materials are the basic point of interest: the aim of the present study is to find new solution to produce carbon fiber-based composites with even more upgraded performances. One intriguing strategy to tackle such an issue has been picked out in the coupling between the carbon fibers and the carbon nanostructures. That for two main reasons: first, carbon nanostructures have shown fancy potentialities for any kind of technological applications since their discovery, second, the chemical affinity between fiber and nanostructure (made of the same element) should be a likely route to approach the typical problems due to thermo-mechanical compatibility. This work is joined in such framework

  8. Multifunctional structural supercapacitor composites based on carbon aerogel modified high performance carbon fiber fabric.

    Science.gov (United States)

    Qian, Hui; Kucernak, Anthony R; Greenhalgh, Emile S; Bismarck, Alexander; Shaffer, Milo S P

    2013-07-10

    A novel multifunctional material has been designed to provide excellent mechanical properties while possessing a high electrochemical surface area suitable for electrochemical energy storage: structural carbon fiber fabrics are embedded in a continuous network of carbon aerogel (CAG) to form a coherent but porous monolith. The CAG-modification process was found to be scalable and to be compatible with a range of carbon fiber fabrics with different surface properties. The incorporation of CAG significantly increased the surface area of carbon fiber fabrics, and hence the electrochemical performance, by around 100-fold, resulting in a CAG-normalized specific electrode capacitance of around 62 F g(-1), determined by cyclic voltammetry in an aqueous electrolyte. Using an ionic liquid (IL) electrolyte, the estimated energy density increased from 0.003 to 1 Wh kg(-1), after introducing the CAG into the carbon fiber fabric. 'Proof-of-concept' multifunctional structural supercapacitor devices were fabricated using an IL-modified solid-state polymer electrolyte as a multifunctional matrix to provide both ionic transport and physical support for the primary fibers. Two CAG-impregnated carbon fabrics were sandwiched around an insulating separator to form a functioning structural electrochemical double layer capacitor composite. The CAG-modification not only improved the electrochemical surface area, but also reinforced the polymer matrix surrounding the primary fibers, leading to dramatic improvements in the matrix-dominated composite properties. Increases in in-plane shear strength and modulus, of up to 4.5-fold, were observed, demonstrating that CAG-modified structural carbon fiber fabrics have promise in both pure structural and multifunctional energy storage applications.

  9. Properties of nanoclay PVA composites materials

    Directory of Open Access Journals (Sweden)

    Mohamed H. M. Ali

    2012-03-01

    Full Text Available Polyvinyl alcohol (PVA/ Na-rich Montmorillonite (MMT nanocomposites were prepared using solution method to create polymer-clay nanocomposite (PCN material. The PCN material was studied using X-ray diffraction (XRD, demonstrating polymer-clay intercalation that has a high d-spacing (lower diffraction angles in the PCN XRD pattern, compared to the pure MMT clay XRD pattern, which has a low d-spacing (high diffraction angles. The nano-scanning electron microscope (NSEM was used to study the morphological image of the PVA, MMT and PCN materials. The results showed that intercalation that took place between the PVA and MMT produced the PCN material. The mechanical properties of the pure PVA and the intercalated polymer material were studied. It was found that the small amount of MMT clay made the tensile modulus and percentage of the total elongation of the nano-composite significantly higher than the pure PVA polymer value, due to polymer-clay intercalation. The thermal stability of the intercalated polymer has been studied using thermal analytical techniques such as thermogravimetric analysis (TGA and differential scanning calorimetry (DSC. The results showed that the PCN material is more thermally stable than the pure PVA polymer.

  10. Multiscale carbon nanotube-carbon fiber reinforcement for advanced epoxy composites.

    Science.gov (United States)

    Bekyarova, E; Thostenson, E T; Yu, A; Kim, H; Gao, J; Tang, J; Hahn, H T; Chou, T-W; Itkis, M E; Haddon, R C

    2007-03-27

    We report an approach to the development of advanced structural composites based on engineered multiscale carbon nanotube-carbon fiber reinforcement. Electrophoresis was utilized for the selective deposition of multi- and single-walled carbon nanotubes (CNTs) on woven carbon fabric. The CNT-coated carbon fabric panels were subsequently infiltrated with epoxy resin using vacuum-assisted resin transfer molding (VARTM) to fabricate multiscale hybrid composites in which the nanotubes were completely integrated into the fiber bundles and reinforced the matrix-rich regions. The carbon nanotube/carbon fabric/epoxy composites showed approximately 30% enhancement of the interlaminar shear strength as compared to that of carbon fiber/epoxy composites without carbon nanotubes and demonstrate significantly improved out-of-plane electrical conductivity.

  11. Multiscale architectured materials with composition and grain size gradients manufactured using high-pressure torsion.

    Science.gov (United States)

    Kang, Ji Yun; Kim, Jung Gi; Park, Hyo Wook; Kim, Hyoung Seop

    2016-05-27

    The concept of multiscale architectured materials is established using composition and grain size gradients. Composition-gradient nanostructured materials are produced from coarse grained interstitial free steels via carburization and high-pressure torsion. Quantitative analyses of the dislocation density using X-ray diffraction and microstructural studies clearly demonstrate the gradients of the dislocation density and grain size. The mechanical properties of the gradient materials are compared with homogeneous nanostructured carbon steel without a composition gradient in an effort to investigate the gradient effect. Based on the above observations, the potential of multiscale architecturing to open a new material property is discussed.

  12. Application of Composite Materials in the Fire Explosion Suppression System

    Institute of Scientific and Technical Information of China (English)

    REN Shah

    2012-01-01

    In order to lighten the weight of the special vehicles and improve their mobility and flexibility, the weight of all subsystems of the whole vehicle must be reduced in the general planning. A fire explosion suppression system is an important subsystem for the self-protection of vehicle, protection of crews and safety of a vehicle. The performances of the special vehicles determine their survival ability and combat capability. The composite bottle is made of aluminum alloy with externally wrapped carbon fiber ; it has been proven by a large number of tests that the new type explosion suppression fire distinguisher made of such composite materials applied in the special vehicle has reliable performance, each of its technical indexes is higher or equal to that of a steel distinguisher, and the composites can also optimize the assembly structure of the bottle, and improve the reliability and corrosion resistance. Most important is that the composite materials can effectively lighten the weight of the fire explosion suppression system to reach the target of weight reduction of the subsystem in general planning.

  13. Metallic nanoparticles deposited on carbon microspheres: novel materials for combinatorial electrochemistry and electroanalysis.

    Science.gov (United States)

    Baron, Ronan; Wildgoose, Gregory G; Compton, Richard G

    2009-04-01

    This review deals with the preparation of metallic nanoparticles on glassy carbon microspheres and the use of these new hybrid materials for combinatorial electrochemistry and electroanalysis. First, the preparation of gold, silver and palladium nanoparticles on glassy carbon microspheres by a simple electroless procedure is described. Then, different types of electrodes modified with glassy carbon microspheres are described. These are: (i) glassy carbon electrodes modified by a composite film of glassy carbon microspheres and multi-walled carbon nanotubes, (ii) basal plane pyrolylic graphite electrodes modified by the abrasive attachment of glassy carbon microspheres and (iii) carbon-epoxy composite electrodes loaded with glassy carbon microspheres. The three types of electrode architectures described consist of metallic nanoparticles embedded in a carbon matrix and each of the electrode macrodisc surfaces actually correspond to a random metallic nanoelectrode array. Carbon-epoxy composite electrodes have good characteristics for their use as practical sensors. Furthermore, the use of several kinds of metallic nanoparticles allows the construction of a multi-analyte electrode and the screening of electroactive materials by following a combinatorial approach.

  14. Carbon nanotube materials for hydrogen storage

    Energy Technology Data Exchange (ETDEWEB)

    Dillon, A.C.; Jones, K.M.; Heben, M.J. [National Renewable Energy Lab., Golden, CO (United States)

    1996-10-01

    Hydrogen burns pollution-free and may be produced from renewable energy resources. It is therefore an ideal candidate to replace fossil fuels as an energy carrier. However, the lack of a convenient and cost-effective hydrogen storage system greatly impedes the wide-scale use of hydrogen in both domestic and international markets. Although several hydrogen storage options exist, no approach satisfies all of the efficiency, size, weight, cost and safety requirements for transportation or utility use. A material consisting exclusively of micropores with molecular dimensions could simultaneously meet all of the requirements for transportation use if the interaction energy for hydrogen was sufficiently strong to cause hydrogen adsorption at ambient temperatures. Small diameter ({approx}1 mm) carbon single-wall nanotubes (SWNTs) are elongated micropores of molecular dimensions, and materials composed predominantly of SWNTs may prove to be the ideal adsorbent for ambient temperature storage of hydrogen. Last year the authors reported that hydrogen could be adsorbed on arc-generated soots containing 12{Angstrom} diameter nanotubes at temperatures in excess of 285K. In this past year they have learned that such adsorption does not occur on activated carbon materials, and that the cobalt nanoparticles present in their arc-generated soots are not responsible for the hydrogen which is stable at 285 K. These results indicate that enhanced adsorption forces within the internal cavities of the SWNTs are active in stabilizing hydrogen at elevated temperatures. This enhanced stability could lead to effective hydrogen storage under ambient temperature conditions. In the past year the authors have also demonstrated that single-wall carbon nanotubes in arc-generated soots may be selectively opened by oxidation in H{sub 2}O resulting in improved hydrogen adsorption, and they have estimated experimentally that the amount of hydrogen stored is {approximately}10% of the nanotube weight.

  15. Modification of carbon nanotubes and synthesis of polymeric composites involving the nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Badamshina, E R; Gafurova, M P; Estrin, Yakov I [Institute of Problems of Chemical Physics, Russian Academy of Sciences, Chernogolovka, Moscow Region (Russian Federation)

    2010-12-29

    The results of studies, mainly published in recent years, on modification of carbon nanotubes and design of composites with these nanotubes for the manufacture of new-generation materials are generalized and analyzed. The methods of modification of the nanotubes by low- and high-molecular compounds and methods of polymer modification by carbon nanotubes are considered. Data on the properties of modified nanotubes are presented. The current and potential applications of materials based on the nanotubes are indicated.

  16. Rheological behavior of composites based on carbon fibers recycled from aircraft waste

    OpenAIRE

    Marcaníková, Lucie; Hausnerová, Berenika; KITANO, Takeshi

    2009-01-01

    Rheological investigation of composite materials prepared from the recycled aircraft waste materials based on thermoset (epoxy/resin) matrix and long carbon fibers (CF) is presented with the aim of their utilization in consumer industry applications. The carbon fibers recovered via thermal process of pyrolysis were cut into about 150 pm length and melt mixed with thermoplastic matrices based on polypropylene (PP) and polyamide 6 (PA) and various modifiers - ethylene-ethyl acrylate-maleic anhy...

  17. Characterization of Triaxial Braided Composite Material Properties for Impact Simulation

    Science.gov (United States)

    Roberts, Gary D.; Goldberg, Robert K.; Biniendak, Wieslaw K.; Arnold, William A.; Littell, Justin D.; Kohlman, Lee W.

    2009-01-01

    The reliability of impact simulations for aircraft components made with triaxial braided carbon fiber composites is currently limited by inadequate material property data and lack of validated material models for analysis. Improvements to standard quasi-static test methods are needed to account for the large unit cell size and localized damage within the unit cell. The deformation and damage of a triaxial braided composite material was examined using standard quasi-static in-plane tension, compression, and shear tests. Some modifications to standard test specimen geometries are suggested, and methods for measuring the local strain at the onset of failure within the braid unit cell are presented. Deformation and damage at higher strain rates is examined using ballistic impact tests on 61- by 61- by 3.2-mm (24- by 24- by 0.125-in.) composite panels. Digital image correlation techniques were used to examine full-field deformation and damage during both quasi-static and impact tests. An impact analysis method is presented that utilizes both local and global deformation and failure information from the quasi-static tests as input for impact simulations. Improvements that are needed in test and analysis methods for better predictive capability are examined.

  18. Mechanical Properties of Graphene Nanoplatelet/Carbon Fiber/Epoxy Hybrid Composites: Multiscale Modeling and Experiments

    Science.gov (United States)

    Hadden, C. M.; Klimek-McDonald, D. R.; Pineda, E. J.; King, J. A.; Reichanadter, A. M.; Miskioglu, I.; Gowtham, S.; Odegard, G. M.

    2015-01-01

    Because of the relatively high specific mechanical properties of carbon fiber/epoxy composite materials, they are often used as structural components in aerospace applications. Graphene nanoplatelets (GNPs) can be added to the epoxy matrix to improve the overall mechanical properties of the composite. The resulting GNP/carbon fiber/epoxy hybrid composites have been studied using multiscale modeling to determine the influence of GNP volume fraction, epoxy crosslink density, and GNP dispersion on the mechanical performance. The hierarchical multiscale modeling approach developed herein includes Molecular Dynamics (MD) and micromechanical modeling, and it is validated with experimental testing of the same hybrid composite material system. The results indicate that the multiscale modeling approach is accurate and provides physical insight into the composite mechanical behavior. Also, the results quantify the substantial impact of GNP volume fraction and dispersion on the transverse mechanical properties of the hybrid composite, while the effect on the axial properties is shown to be insignificant.

  19. Mechanical Properties of Graphene Nanoplatelet Carbon Fiber Epoxy Hybrid Composites: Multiscale Modeling and Experiments

    Science.gov (United States)

    Hadden, Cameron M.; Klimek-McDonald, Danielle R.; Pineda, Evan J.; King, Julie A.; Reichanadter, Alex M.; Miskioglu, Ibrahim; Gowtham, S.; Odegard, Gregory M.

    2015-01-01

    Because of the relatively high specific mechanical properties of carbon fiber/epoxy composite materials, they are often used as structural components in aerospace applications. Graphene nanoplatelets (GNPs) can be added to the epoxy matrix to improve the overall mechanical properties of the composite. The resulting GNP/carbon fiber/epoxy hybrid composites have been studied using multiscale modeling to determine the influence of GNP volume fraction, epoxy crosslink density, and GNP dispersion on the mechanical performance. The hierarchical multiscale modeling approach developed herein includes Molecular Dynamics (MD) and micromechanical modeling, and it is validated with experimental testing of the same hybrid composite material system. The results indicate that the multiscale modeling approach is accurate and provides physical insight into the composite mechanical behavior. Also, the results quantify the substantial impact of GNP volume fraction and dispersion on the transverse mechanical properties of the hybrid composite, while the effect on the axial properties is shown to be insignificant.

  20. Compositions and methods for cancer treatment using targeted carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, Jr., Roger G.; Resasco, Daniel E.; Neves, Luis Filipe Ferreira

    2016-11-29

    Compositions for detecting and/or destroying cancer tumors and/or cancer cells via photodynamic therapy are disclosed, as well as methods of use thereof. The compositions comprise a linking protein or peptide attached to or otherwise physically associated with a carbon nanotube to form a targeted protein-carbon nanotube complex.