WorldWideScience

Sample records for canyon wind integration

  1. Klondike III/Biglow Canyon Wind Integration Project; Record of Decision, October 25, 2006.

    Energy Technology Data Exchange (ETDEWEB)

    United States. Bonneville Power Administration

    2006-10-25

    The Bonneville Power Administration (BPA) has decided to implement the Proposed Action identified in the Klondike III/Biglow Canyon Wind Integration Project Final Environmental Impact Statement (FEIS) (DOE/EIS-0374, September 2006). Under the Proposed Action, BPA will offer PPM Energy, Inc. (PPM) contract terms for interconnection of the proposed Klondike III Wind Project, located in Sherman County, Oregon, with the Federal Columbia River Transmission System (FCRTS). BPA will also offer Portland General Electric (PGE)1 contract terms for interconnection of its proposed Biglow Canyon Wind Farm, also located in Sherman County, Oregon, with the FCRTS, as proposed in the FEIS. To interconnect these wind projects, BPA will build and operate a 12-mile long, 230-kilovolt (kV) double-circuit transmission line between the wind projects and BPA's new 230-kV John Day Substation in Sherman County, Oregon. BPA will also expand its existing 500-kV John Day Substation.

  2. Klondike III/Biglow Canyon Wind Integration Project; Final Environmental Impact Statement, September 2006.

    Energy Technology Data Exchange (ETDEWEB)

    United States. Bonneville Power Administration

    2006-09-01

    BPA has been asked by PPM Energy, Inc. to interconnect 300 megawatts (MW) of electricity generated from the proposed Klondike III Wind Project to the Federal Columbia River Transmission System. Orion Energy LLC has also asked BPA to interconnect 400 MW of electricity from its proposed Biglow Canyon Wind Farm, located north and east of the proposed Klondike III Wind Project. (Portland General Electric recently bought the rights to develop the proposed Biglow Canyon Wind Farm from Orion Energy, LLC.) Both wind projects received Site Certificates from the Oregon Energy Facility Siting Council on June 30, 2006. To interconnect these projects, BPA would need to build and operate a 230-kV double-circuit transmission line about 12 miles long, expand one substation and build one new substation. The wind projects would require wind turbines, substation(s), access roads, and other facilities. Two routes for the transmission line are being considered. Both begin at PPM's Klondike Schoolhouse Substation then travel north (Proposed Action) or north and westerly (Middle Alternative) to a new BPA 230-kV substation next to BPA's existing John Day 500-kV Substation. BPA is also considering a No Action Alternative in which BPA would not build the transmission line and would not interconnect the wind projects. The proposed BPA and wind projects would be located on private land, mainly used for agriculture. If BPA decides to interconnect the wind projects, construction of the BPA transmission line and substation(s) could commence as early as the winter of 2006-07. Both wind projects would operate for much of each year for at least 20 years. The proposed projects would generally create no or low impacts. Wildlife resources and local visual resources are the only resources to receive an impact rating other than ''none'' or ''low''. The low to moderate impacts to wildlife are from the expected bird and bat mortality and the cumulative

  3. Diablo Canyon plant information management system and integrated communication system

    Energy Technology Data Exchange (ETDEWEB)

    Stanley, J.W.; Groff, C.

    1990-06-01

    The implementation of a comprehensive maintenance system called the plant information management system (PIMS) at the Diablo Canyon plant, together with its associated integrated communication system (ICS), is widely regarded as the most comprehensive undertaking of its kind in the nuclear industry. This paper provides an overview of the program at Diablo Canyon, an evaluation of system benefits, and highlights the future course of PIMS.

  4. 75 FR 27550 - Electrical Interconnection of the Juniper Canyon I Wind Project

    Science.gov (United States)

    2010-05-17

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Bonneville Power Administration Electrical Interconnection of the Juniper Canyon I Wind Project AGENCY: Bonneville Power Administration (BPA), Department of Energy (DOE). ACTION: Notice of Availability of...

  5. 77 FR 55829 - Western Area Power Administration; Grapevine Canyon Wind Project Record of Decision (DOE/EIS-0427)

    Science.gov (United States)

    2012-09-11

    ... Area Power Administration; Grapevine Canyon Wind Project Record of Decision (DOE/EIS-0427) AGENCY... Grapevine Canyon Wind Project was published in the Federal Register (77 FR 34041). After considering the... proposed wind park would be built in one or more phases, dependent on one or more power sale contracts....

  6. 75 FR 18201 - Juniper Canyon Wind Power, LLC; Supplemental Notice That Initial Market-Based Rate Filing...

    Science.gov (United States)

    2010-04-09

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Federal Energy Regulatory Commission Juniper Canyon Wind Power, LLC; Supplemental Notice That Initial Market... supplemental notice in the above-referenced proceeding of Juniper Canyon Wind Power, LLC's application...

  7. Combining Wind-Tunnel and Field Measurements of Street-Canyon Flow via Stochastic Estimation

    Science.gov (United States)

    Perret, Laurent; Blackman, Karin; Savory, Eric

    2016-06-01

    We demonstrate how application of the stochastic estimation method can be employed to combine spatially well-resolved wind-tunnel particle image velocimetry measurements with instantaneous velocity signals from a limited number of sensors (six sonic anemometers located within the canyon in the present case) to predict full-scale flow dynamics in an entire street-canyon cross-section. The investigated configuration corresponds to a street-canyon flow in a neutrally stratified atmospheric boundary layer with the oncoming flow being perpendicular to the main canyon axis. Data were obtained during both full-scale and 1:200-scale wind-tunnel experiments. The performance of the proposed method is investigated using both wind-tunnel data and signals from five sonic anemometers to predict the velocity from the sixth one. In particular, based on analysis of the influence of the high-frequency velocity fluctuations on the quality of the reconstruction, it is shown that stochastic estimation is able to correctly reproduce the large-scale temporal features of the flow with the present set-up. The full dataset is then used to spatially extrapolate the instantaneous flow measured by the six sonic anemometers and perform detailed analysis of instantaneous flow features. The main features of the flow, such as the presence of the shear layer that develops over the canyon and the intermittent ejection and penetration events across the canyon opening, are well predicted by stochastic estimation. In addition, thanks to the high spatial resolution made possible by the technique, the intermittency of the main vortical structure existing within the canyon is demonstrated, as well as its meandering motion in the canyon cross-section. It is also shown that the canyon flow, particularly its spanwise component, is affected by large-scale fluctuations of low temporal frequency along the canyon axis. Finally, the proposed techniques based on wind-tunnel data can prove useful for a priori

  8. Integrated Wind Power Planning Tool

    DEFF Research Database (Denmark)

    Rosgaard, Martin H.; Hahmann, Andrea N.; Nielsen, Torben S.;

    This poster presents the Public Service Obligation (PSO) funded project PSO 10464 "Integrated Wind Power Planning Tool". The project goal is to integrate a Numerical Weather Prediction (NWP) model with statistical tools in order to assess wind power fluctuations, with focus on short term...... forecasting for existing wind farms, as well as long term power system planning for future wind farms....

  9. Correlation between traffic density and particle size distribution in a street canyon and the dependence on wind direction

    Directory of Open Access Journals (Sweden)

    J. Voigtländer

    2006-05-01

    Full Text Available Combustion of fossil fuel in gasoline and diesel powered vehicles is a major source of aerosol particles in a city. In a street canyon, the number concentration of particles smaller than 300 nm in diameter, which can be inhaled and cause serious health effects, is dominated by particles originating from this source.

    In this study we measured both, particle number size distribution and traffic density continuously in a characteristic street canyon in Germany for a time period of 6 months. The street canyon with multistory buildings and 4 traffic lanes is very typical for larger cities. Thus, the measurements are also representative for many other street canyons. In contrast to previous studies, we measured and analyzed the particle number size distribution with high size resolution using a Twin Differential Mobility Analyzer (TDMPS. The measured size range was from 3 to 800 nm, separated into 40 size channels.

    Correlation coefficients between particle number concentration for integrated size ranges and traffic up to 0.5 counts were determined. Correlations were also calculated for each of the 40 size channels of the DMPS system, respectively. We found two maxima of the correlation coefficient for particles about 10 nm and in the size range 60–80 nm in diameter.

    Furthermore, correlations between traffic and particles in dependence of meteorological data were calculated. Relevant parameters were identified by a multiple regression method. In our experiment only wind parameters have influenced the particle number concentration significantly. Very high correlation coefficients (up to 0.85 could be observed in the lee side of the street canyon as well as particles in the range between 60 and 80 nm in diameter. These values are significantly higher than correlation coefficients for other wind directions and other particle sizes. A minimum was found in the luff side of the street. These findings are in good agreement

  10. Offshore Wind Data Integration

    OpenAIRE

    Nguyen, Trinh Hoang

    2014-01-01

    Using renewable energy to meet the future electricity consumption and to reduce environmental impact is a significant target of many countries around the world. Wind power is one of the most promising renewable energy technologies. In particular, the development of offshore wind power is increasing rapidly due to large areas of wind resources. However, offshore wind is encountering big challenges such as effective use of wind power plants, reduced cost of installation as well a...

  11. Numerical Study on the Impact of Ground Heating and Ambient Wind Speed on Flow Fields in Street Canyons

    Institute of Scientific and Technical Information of China (English)

    LI Lei; YANG Lin; ZHANG Li-Jie; JIANG Yin

    2012-01-01

    The impact of ground heating on flow fields in street canyons under different ambient wind speed conditions was studied based on numerical methods.A series of numerical tests were performed,and three factors including height-to-width (H/W) ratio,ambient wind speed and ground heating intensity were taken into account.Three types of street canyon with H/W ratios of 0.5,1.0 and 2.0,respectively,were used in the simulation and seven speed values ranging from 0.0 to 3.0 m s-1 were set for the ambient wind speed.The ground heating intensity,which was defined as the difference between the ground temperature and air temperature,ranged from 10 to 40 K with an increase of 10 K in the tests.The results showed that under calm conditions,ground heating could induce circulation with a wind speed of around 1.0 m s-1,which is enough to disperse pollutants in a street canyon.It was also found that an ambient wind speed threshold may exist for street canyons with a fixed H/W ratio.When ambient wind speed was lower than the threshold identified in this study,the impact of the thermal effect on the flow field was obvious,and there existed a multi-vortex flow pattern in the street canyon.When the ambient wind speed was higher than the threshold,the circulation pattern was basically determined by dynamic effects.The tests on the impact of heating intensity showed that a higher ground heating intensity could strengthen the vortical flow within the street canyon,which would help improve pollutant diffusion capability in street canyons.

  12. Integrated Wind Power Planning Tool

    DEFF Research Database (Denmark)

    Rosgaard, M. H.; Giebel, Gregor; Nielsen, T. S.;

    2012-01-01

    This poster presents the current state of the public service obligation (PSO) funded project PSO 10464, with the working title "Integrated Wind Power Planning Tool". The project commenced October 1, 2011, and the goal is to integrate a numerical weather prediction (NWP) model with purely...... statistical tools in order to assess wind power fluctuations, with focus on long term power system planning for future wind farms as well as short term forecasting for existing wind farms. Currently, wind power fluctuation models are either purely statistical or integrated with NWP models of limited...... resolution. With regard to the latter, one such simulation tool has been developed at the Wind Energy Division, Risø DTU, intended for long term power system planning. As part of the PSO project the inferior NWP model used at present will be replaced by the state-of-the-art Weather Research & Forecasting...

  13. Simulation of wind-driven dispersion of fire pollutants in a street canyon using FDS.

    Science.gov (United States)

    Pesic, Dusica J; Blagojevic, Milan Dj; Zivkovic, Nenad V

    2014-01-01

    Air quality in urban areas attracts great attention due to increasing pollutant emissions and their negative effects on human health and environment. Numerous studies, such as those by Mouilleau and Champassith (J Loss Prevent Proc 22(3): 316-323, 2009), Xie et al. (J Hydrodyn 21(1): 108-117, 2009), and Yassin (Environ Sci Pollut Res 20(6): 3975-3988, 2013) focus on the air pollutant dispersion with no buoyancy effect or weak buoyancy effect. A few studies, such as those by Hu et al. (J Hazard Mater 166(1): 394-406, 2009; J Hazard Mater 192(3): 940-948, 2011; J Civ Eng Manag (2013)) focus on the fire-induced dispersion of pollutants with heat buoyancy release rate in the range from 0.5 to 20 MW. However, the air pollution source might very often be concentrated and intensive, as a consequence of the hazardous materials fire. Namely, transportation of fuel through urban areas occurs regularly, because it is often impossible to find alternative supply routes. It is accompanied with the risk of fire accident occurrences. Accident prevention strategies require analysis of the worst scenarios in which fire products jeopardize the exposed population and environment. The aim of this article is to analyze the impact of wind flow on air pollution and human vulnerability to fire products in a street canyon. For simulation of the gasoline tanker truck fire as a result of a multivehicle accident, computational fluid dynamics large eddy simulation method has been used. Numerical results show that the fire products flow vertically upward, without touching the walls of the buildings in the absence of wind. However, when the wind velocity reaches the critical value, the products touch the walls of the buildings on both sides of the street canyon. The concentrations of carbon monoxide and soot decrease, whereas carbon dioxide concentration increases with the rise of height above the street canyon ground level. The longitudinal concentration of the pollutants inside the street

  14. Wind Tunnel Studies of a Pedestrian-Level Wind Environment in a Street Canyon between a High-Rise Building with a Podium and Low-Level Attached Houses

    OpenAIRE

    Chien-Yuan Kuo; Chun-Ta Tzeng; Ming-Chin Ho; Chi-Ming Lai

    2015-01-01

    The pedestrian-level wind environment quality in street canyons formed by high-rise buildings and other low-level buildings could be affected by multiple factors, such as the height and geometry of the surrounding buildings, street width, wind direction, and wind speed. This study conducted wind tunnel experiments to determine the characteristics of the pedestrian-level wind environment in street canyons under different conditions, including different street widths, podium heights, and approa...

  15. Grid integration of wind energy

    CERN Document Server

    Heier, Siegfried

    2014-01-01

    This timely update provides detailed treatment of the integration of wind power into electrical power systems, including brand new material on offshore wind power farms and technologies This third English edition is based on new material from the fourth and fifth German editions (Windkraftanlagen: Systemauslegung, Netzintegration und Regelung, 5. Auflage, published by Teubner B.G. Gmbh, July 2009). It answers the question of how, with the proper control and direction, wind turbines can be made to operate more similarly to conventional power plants. The revised third edition addresses the engin

  16. Integrated Wind Power Planning Tool

    DEFF Research Database (Denmark)

    Rosgaard, M. H.; Hahmann, Andrea N.; Nielsen, T. S.;

    This poster describes the status as of April 2012 of the Public Service Obligation (PSO) funded project PSO 10464 \\Integrated Wind Power Planning Tool". The project goal is to integrate a meso scale numerical weather prediction (NWP) model with a statistical tool in order to better predict short...... term power variation from off shore wind farms, as well as to conduct forecast error assessment studies in preparation for later implementation of such a feature in an existing simulation model. The addition of a forecast error estimation feature will further increase the value of this tool, as it...

  17. Wind energy integration in Ontario

    International Nuclear Information System (INIS)

    This PowerPoint presentation discussed some of the issues that Ontario's Independent Electricity System Operator (IESO) must now consider in order to successfully integrate wind energy into the province's electricity grid. Wind energy is expected to form a significant portion of the province's projected electricity supply in the future. However, the variability of wind energy remains a challenge to system operators and can have an impact on system reliability. The variable generation capacity of wind and solar energy can cause ramping events. The ability to predict output from variable resources such as wind energy will be essential for maintaining market efficiency and system reliability. Direct telemetry and reporting technologies may be needed to ensure the reliability of large-scale embedded wind and solar generators. However, the integration of renewable energy into the electricity supply system will help to resolve issues related to surplus baseload generation. The IESO is continuing to define operating needs for the future while working with industry to develop new standards that ensure the reliable supply of electricity. tabs., figs.

  18. Integrated roof wind energy system

    Directory of Open Access Journals (Sweden)

    Moonen S.P.G.

    2012-10-01

    Full Text Available Wind is an attractive renewable source of energy. Recent innovations in research and design have reduced to a few alternatives with limited impact on residential construction. Cost effective solutions have been found at larger scale, but storage and delivery of energy to the actual location it is used, remain a critical issue. The Integrated Roof Wind Energy System is designed to overcome the current issues of urban and larger scale renewable energy system. The system is built up by an axial array of skewed shaped funnels that make use of the Venturi Effect to accelerate the wind flow. This inventive use of shape and geometry leads to a converging air capturing inlet to create high wind mass flow and velocity toward a vertical-axis wind turbine in the top of the roof for generation of a relatively high amount of energy. The methods used in this overview of studies include an array of tools from analytical modelling, PIV wind tunnel testing, and CFD simulation studies. The results define the main design parameters for an efficient system, and show the potential for the generation of high amounts of renewable energy with a novel and effective system suited for the built environment.

  19. Integrated roof wind energy system

    Science.gov (United States)

    Suma, A. B.; Ferraro, R. M.; Dano, B.; Moonen, S. P. G.

    2012-10-01

    Wind is an attractive renewable source of energy. Recent innovations in research and design have reduced to a few alternatives with limited impact on residential construction. Cost effective solutions have been found at larger scale, but storage and delivery of energy to the actual location it is used, remain a critical issue. The Integrated Roof Wind Energy System is designed to overcome the current issues of urban and larger scale renewable energy system. The system is built up by an axial array of skewed shaped funnels that make use of the Venturi Effect to accelerate the wind flow. This inventive use of shape and geometry leads to a converging air capturing inlet to create high wind mass flow and velocity toward a vertical-axis wind turbine in the top of the roof for generation of a relatively high amount of energy. The methods used in this overview of studies include an array of tools from analytical modelling, PIV wind tunnel testing, and CFD simulation studies. The results define the main design parameters for an efficient system, and show the potential for the generation of high amounts of renewable energy with a novel and effective system suited for the built environment.

  20. Nebraska Statewide Wind Integration Study: Executive Summary

    Energy Technology Data Exchange (ETDEWEB)

    EnerNex Corporation, Knoxville, Tennessee; Ventyx, Atlanta, Georgia; Nebraska Power Association, Lincoln, Nebraska

    2010-03-01

    Wind generation resources in Nebraska will play an increasingly important role in the environmental and energy security solutions for the state and the nation. In this context, the Nebraska Power Association conducted a state-wide wind integration study.

  1. Wind power integration: from individual wind turbine to wind park as a power plant

    NARCIS (Netherlands)

    Zhou, Y.

    2009-01-01

    As power capacities of single wind turbine, single wind park and total wind power installation are continuously increasing, the wind power begins to challenge the safety operation of the power system. This thesis focuses on the grid integration aspects such as the dynamic behaviours of wind power du

  2. Evaluation of numerical flow and dispersion simulations for street canyons with avenue-like tree planting by comparison with wind tunnel data

    OpenAIRE

    Gromke, CB Christof; Buccolieri, R; Sabatino, S Di; Ruck, B.

    2008-01-01

    Abstract: Flow and traffic-originated pollutant dispersion in an urban street canyon with avenue-like tree planting have been studied by means of wind tunnel and CFD investigations. The study comprises tree planting of different crown porosity, planted in two rows within a canyon of street width to building height ratio W/H = 2 and street length to building height ratio L/H = 10 exposed to a perpendicular approaching boundary layer flow. Numerical simulations have been performed with...

  3. Wind power potential and integration in Africa

    Directory of Open Access Journals (Sweden)

    Agbetuyi, A.F.

    2013-03-01

    Full Text Available Wind energy penetration into power networks is increasing very rapidly all over the world. The great concern about global warming and continued apprehensions about nuclear power around the world should drive most countries in Africa into strong demand for wind generation because of its advantages which include the absence of harmful emissions, very clean and almost infinite availability of wind that is converted into electricity. This paper shows the power available in the wind. It also gives an overview of the wind power potential and integration in some selected Africa countries like Egypt, Morocco, South Africa and Nigeria and the challenges of wind power integration in Africa’s continent are also discussed. The Northern part of Africa is known to be Africa’s Wind pioneers having installed and connected the Wind Energy Converters (WEC to the grid. About 97% of the continent’s total wind installations are located in Egypt, Morocco and Tunisia. Research work should commence on the identified sites with high wind speeds in those selected Africa countries, so that those potential sites can be connected to the grid. This is because the ability of a site to sufficiently accommodate wind generation not only depends on wind speeds but on its ability to interconnect to the existing grid. If these wind energy potentials are tapped and connected to the grid, the erratic and epileptic power supply facing most countries in Africa will be reduced; thereby reducing rural-urban migration and more jobs will be created.

  4. Eastern wind integration and transmission study overview

    Energy Technology Data Exchange (ETDEWEB)

    Corbus, D. [United States Dept. of Energy, Golden, CO (United States). National Renewable Energy Laboratory

    2009-07-01

    This presentation discussed the electricity system operational impacts and benefits of long distance transmission accessing multiple wind resources in New England. The aim of the eastern wind integration and transmission study (EWITS) was to determine the impact of geographical diversity on system variability, and to understand the role of wind forecasting in ensuring reliability. Mesoscale modelling was evaluated, as well as transmission and integration studies. Mesoscale modelling is conducted to identify wind sites and develop high quality wind resource data sets, as well as to develop wind power plant outputs. Scenarios for 20 and 30 per cent wind integration includes the development of local resources with lower capacity factors; and high capacity factor wind development with larger transmission components. All the scenarios required the use of offshore wind resources. The study also examined export capacity for each of the studied areas. Wind integration, reliability analyses, and hourly modelling approaches were reviewed. Future research will include sensitivity studies related to carbon pricing and stochastic modelling. tabs., figs.

  5. PG and E Diablo canyon nuclear power plant, plant information management system, integrated communications system

    International Nuclear Information System (INIS)

    This paper presents the architecture, design and implementation of a plant-wide industrial network for Pacific Gas and Electric Company's (PG and E) Diablo Canyon Nuclear Power Plant (DCPP). The network is referred to as the Integrated Communications System (ICS) and provides a broadband backbone cable plant and communications infrastructure that are capable of reliably carrying data, video, telemetry, image and voice information throughout the plant site. It is used to interconnect 400-800 IBM 3270 PC workstations to the site's numerous computer systems, as well as providing workstation users with several value-added applications

  6. Conference on wind energy and grid integration

    International Nuclear Information System (INIS)

    The French-German office for Renewable energies (OFAEnR) organised a conference on the grid integration of wind farms. In the framework of this French-German exchange of experience, more than 80 participants exchanged views on the evolutions of tariffs and licensing procedures, and on grid capacity improvements and production forecasts. This document brings together the available presentations (slides) made during this event: 1 - The necessary evolution of billing and procedures for wind turbines connection to the grid in France (Didier Laffaille); 2 - Improvement of wind turbines integration to the grid in the framework of the EEG 2009 law (Jens Boemer); 3 - Decentralized power generation on the French power grids - 15, 20 kV and low voltage (Jean-Luc Fraisse); 4 - GOTTESWIND? Solution for the future: towards a grid evolution (Herve Mignon); 5 - Production forecasts in Germany - State-of-the-art and challenges for the grid exploitation (Kurt Rohrig); 6 - High-voltage lines capacity evaluation in meteorological situations with high wind energy production (Matthias Lange); 7 - The IPES project for the integration of wind energy production in the exploitation of the French power system (Jean-Pierre Gonot); 8 - Experience feedback from a wind turbine manufacturer in France and in Germany (Daniel Bagusche); 9 - Solutions for grid security improvement and capacity enhancement: cooperation between grid and power plant operators (Stefan Wagner); 10 - Open questions on wind energy integration to French and German grids (Johannes Schiel)

  7. An Appropriate Wind Model for Wind Integrated Power Systems Reliability Evaluation Considering Wind Speed Correlations

    Directory of Open Access Journals (Sweden)

    Rajesh Karki

    2013-02-01

    Full Text Available Adverse environmental impacts of carbon emissions are causing increasing concerns to the general public throughout the world. Electric energy generation from conventional energy sources is considered to be a major contributor to these harmful emissions. High emphasis is therefore being given to green alternatives of energy, such as wind and solar. Wind energy is being perceived as a promising alternative. This source of energy technology and its applications have undergone significant research and development over the past decade. As a result, many modern power systems include a significant portion of power generation from wind energy sources. The impact of wind generation on the overall system performance increases substantially as wind penetration in power systems continues to increase to relatively high levels. It becomes increasingly important to accurately model the wind behavior, the interaction with other wind sources and conventional sources, and incorporate the characteristics of the energy demand in order to carry out a realistic evaluation of system reliability. Power systems with high wind penetrations are often connected to multiple wind farms at different geographic locations. Wind speed correlations between the different wind farms largely affect the total wind power generation characteristics of such systems, and therefore should be an important parameter in the wind modeling process. This paper evaluates the effect of the correlation between multiple wind farms on the adequacy indices of wind-integrated systems. The paper also proposes a simple and appropriate probabilistic analytical model that incorporates wind correlations, and can be used for adequacy evaluation of multiple wind-integrated systems.

  8. Research of Micro-sitting Methods for Canyon Wind Power Project%高原峡谷风电场微观选址方法研究

    Institute of Scientific and Technical Information of China (English)

    任腊春; 钟滔; 李良县

    2015-01-01

    着重分析了高原峡谷风电场风速相关性、风速切变、湍流强度、风能资源分布等主要风况特性,提出了高原峡谷风电场微观选址流程和方法,分析研究了高原峡谷风电场微观选址可能的影响因素并给出了风电机组与影响因素的最小建议安全距离,形成了有效的设计方法和经验。结合实际工程案例分析结果验证该设计方法基本可行,可为同类风电场微观选址设计提供借鉴参考。%The wind energy characteristics, such as wind speed correlation, wind shear turbulence intensity and wind power distribution, are analyzed for plateau canyon wind farm. The process and method of micro-sitting for canyon wind power project is proposed, the restriction factors of WTGS layout are analyzed and the recommended distance between the position of WTGS and affected objects is given. The availability and feasibility of the design method for the micro-sitting of canyon wind farm is proved by project cases. The method and experiences can provide references for the micro-sitting design of similar wind farms.

  9. Wind power integration connection and system operational aspects

    CERN Document Server

    Fox, Brendan

    2014-01-01

    Wind Power Integration provides a wide-ranging discussion on all major aspects of wind power integration into electricity supply systems. This second edition has been fully revised and updated to take account of the significant growth in wind power deployment in the past few years. New discussions have been added to describe developments in wind turbine generator technology and control, the network integration of wind power, innovative ways to integrate wind power when its generation potential exceeds 50% of demand, case studies on how forecasting errors have affected system operation, and an update on how the wind energy sector has fared in the marketplace. Topics covered include: the development of wind power technology and its world-wide deployment; wind power technology and the interaction of various wind turbine generator types with the utility network; and wind power forecasting and the challenges faced by wind energy in modern electricity markets.

  10. Technology solutions for wind integration in ERCOT

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2015-01-03

    Texas has for more than a decade led all other states in the U.S. with the most wind generation capacity on the U.S. electric grid. The State recognized the value that wind energy could provide, and committed early on to build out the transmission system necessary to move power from the windy regions in West Texas to the major population centers across the state. It also signaled support for renewables on the grid by adopting an aggressive renewable portfolio standard (RPS). The joining of these conditions with favorable Federal tax credits has driven the rapid growth in Texas wind capacity since its small beginning in 2000. In addition to the major transmission grid upgrades, there have been a number of technology and policy improvements that have kept the grid reliable while adding more and more intermittent wind generation. Technology advancements such as better wind forecasting and deployment of a nodal market system have improved the grid efficiency of wind. Successful large scale wind integration into the electric grid, however, continues to pose challenges. The continuing rapid growth in wind energy calls for a number of technology additions that will be needed to reliably accommodate an expected 65% increase in future wind resources. The Center for the Commercialization of Electric Technologies (CCET) recognized this technology challenge in 2009 when it submitted an application for funding of a regional demonstration project under the Recovery Act program administered by the U.S. Department of Energy1. Under that program the administration announced the largest energy grid modernization investment in U.S. history, making available some $3.4 billion in grants to fund development of a broad range of technologies for a more efficient and reliable electric system, including the growth of renewable energy sources like wind and solar. At that time, Texas was (and still is) the nation’s leader in the integration of wind into the grid, and was investing heavily

  11. TECHNOLOGY SOLUTIONS FOR WIND INTEGRATION IN ERCOT

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2015-01-03

    Texas has for more than a decade led all other states in the U.S. with the most wind generation capacity on the U.S. electric grid. The State recognized the value that wind energy could provide, and committed early on to build out the transmission system necessary to move power from the windy regions in West Texas to the major population centers across the state. It also signaled support for renewables on the grid by adopting an aggressive renewable portfolio standard (RPS). The joining of these conditions with favorable Federal tax credits has driven the rapid growth in Texas wind capacity since its small beginning in 2000. In addition to the major transmission grid upgrades, there have been a number of technology and policy improvements that have kept the grid reliable while adding more and more intermittent wind generation. Technology advancements such as better wind forecasting and deployment of a nodal market system have improved the grid efficiency of wind. Successful large scale wind integration into the electric grid, however, continues to pose challenges. The continuing rapid growth in wind energy calls for a number of technology additions that will be needed to reliably accommodate an expected 65% increase in future wind resources. The Center for the Commercialization of Electric Technologies (CCET) recognized this technology challenge in 2009 when it submitted an application for funding of a regional demonstration project under the Recovery Act program administered by the U.S. Department of Energy1. Under that program the administration announced the largest energy grid modernization investment in U.S. history, making available some $3.4 billion in grants to fund development of a broad range of technologies for a more efficient and reliable electric system, including the growth of renewable energy sources like wind and solar. At that time, Texas was (and still is) the nation’s leader in the integration of wind into the grid, and was investing heavily

  12. Dispersion study in a street canyon with tree planting by means of wind tunnel and numerical investigations - Evaluation of CFD data with experimental data

    Science.gov (United States)

    Gromke, Christof; Buccolieri, Riccardo; Di Sabatino, Silvana; Ruck, Bodo

    This paper is devoted to the study of flow and traffic exhaust dispersion in urban street canyons with avenue-like tree planting. The influence of tree planting with different crown porosity was investigated. Wind tunnel experiments for perpendicular approaching flow showed that avenue-like tree planting cause increases in exhaust concentrations at the leeward wall as tree crowns reduce the vortex found in the outer regions of the tree-free street canyon and the vertically entering volume flow rate at the canyon-roof top interface. This results in less ventilation and consequently larger concentrations in proximity of the leeward wall. At the windward wall, decreases in concentration are due to the upward moving stream in front of the leeward wall which extends farther into the skimming above roof flow and is better mixed. The clean air entrained in front of the windward wall mixes with air inside the street canyon leading to smaller concentrations. Experiments performed in the wind tunnel with different tree crown porosities did not indicate substantial changes in the flow and concentration fields. The porous model crowns investigated behaved almost like impermeable objects when arranged in a sheltered position and wind speeds are relatively small as in the street canyon. The above described experiments have been also investigated by means of numerical simulations with the CFD code FLUENT™, rarely applied to this type of problems. The standard k- ɛ turbulence model and the Reynolds Stress Model were used for flow while the Eulerian advection diffusion scheme has been used for dispersion. Both models reproduced qualitatively the main aspects found in wind tunnel experiments, even though they underestimated flow velocities. Improvement of CFD dispersion performance was obtained by increasing the diffusivity through the turbulent Schmidt number Sc t. Overall we found that the k- ɛ model failed to capture the complex structure of dispersion process in the presence

  13. Positional Accuracy of Airborne Integrated Global Positioning and Inertial Navigation Systems for Mapping in Glen Canyon, Arizona

    Science.gov (United States)

    Sanchez, Richard D.; Hothem, Larry D.

    2002-01-01

    High-resolution airborne and satellite image sensor systems integrated with onboard data collection based on the Global Positioning System (GPS) and inertial navigation systems (INS) may offer a quick and cost-effective way to gather accurate topographic map information without ground control or aerial triangulation. The Applanix Corporation?s Position and Orientation Solutions for Direct Georeferencing of aerial photography was used in this project to examine the positional accuracy of integrated GPS/INS for terrain mapping in Glen Canyon, Arizona. The research application in this study yielded important information on the usefulness and limits of airborne integrated GPS/INS data-capture systems for mapping.

  14. Integrated Project Management Planning for the Deactivation of the Savannah River Site F-Canyon Complex

    Energy Technology Data Exchange (ETDEWEB)

    Clark, T.G.

    2000-12-01

    This paper explains the planning process that is being utilized by the Westinghouse Savannah River Company to take the F-Canyon Complex facilities from operations to a deactivated condition awaiting final decommissioning.

  15. Nova Scotia wind integration study : final report

    International Nuclear Information System (INIS)

    An independent study was commissioned by the Nova Scotia Department of Energy to identify and assess the impacts of integrating large scale wind power generation into Nova Scotia's electric power system. The purpose of the study was to help Nova Scotia's efforts towards building its renewable energy supply, in order to secure a local energy resource and to protect the environment. This report provided an overview of Nova Scotia's electric power sector, including organizations involved; existing generation system; existing transmission system; renewable energy standards; Nova Scotia Power integrated resource plan; and 2007 renewable energy request for proposals. The major assumptions for the study that were discussed included system parameters; system capacity reserve requirements; expansion plans to 2020; and allocation of new wind generation by zone. Wind resource data and system dispatch modeling were also presented and transmission system modeling was outlined. This included a discussion of steady state reliability requirements; inputs to the load flow model; load flow study and contingency analysis; intra-province transmission congestion; and potential impacts on system security. The report also presented an approach to impact analysis and mitigation such as the impact on greenhouse gas and other air emissions and the impact of wind energy prices on system costs. It was concluded that one of the most important factors in evaluation of the economic impact of wind power integration is the forecasted fuel prices for the thermal units. If the fuel prices had varied significantly from the forecasted values, the study economic impact results could have been quite different. 55 tabs., 64 figs., 1 appendix

  16. Flexible reserve markets for wind integration

    Science.gov (United States)

    Fernandez, Alisha R.

    The increased interconnection of variable generation has motivated the use of improved forecasting to more accurately predict future production with the purpose to lower total system costs for balancing when the expected output exceeds or falls short of the actual output. Forecasts are imperfect, and the forecast errors associated with utility-scale generation from variable generators need new balancing capabilities that cannot be handled by existing ancillary services. Our work focuses on strategies for integrating large amounts of wind generation under the flex reserve market, a market that would called upon for short-term energy services during an under or oversupply of wind generation to maintain electric grid reliability. The flex reserve market would be utilized for time intervals that fall in-between the current ancillary services markets that would be longer than second-to-second energy services for maintaining system frequency and shorter than reserve capacity services that are called upon for several minutes up to an hour during an unexpected contingency on the grid. In our work, the wind operator would access the flex reserve market as an energy service to correct for unanticipated forecast errors, akin to paying the generators participating in the market to increase generation during a shortfall or paying the other generators to decrease generation during an excess of wind generation. Such a market does not currently exist in the Mid-Atlantic United States. The Pennsylvania-New Jersey-Maryland Interconnection (PJM) is the Mid-Atlantic electric grid case study that was used to examine if a flex reserve market can be utilized for integrating large capacities of wind generation in a lowcost manner for those providing, purchasing and dispatching these short-term balancing services. The following work consists of three studies. The first examines the ability of a hydroelectric facility to provide short-term forecast error balancing services via a flex

  17. Integrated installation for offshore wind turbines

    Energy Technology Data Exchange (ETDEWEB)

    Way, J.; Bowerman, H.

    2003-07-01

    A project to investigate the feasibility of integrating the offshore installation of foundation, turbine and tower for offshore wind turbines into one operation is described. Three separate objectives are listed. They are: (1) Telescopic tower study - reversible process incorporating lift and lock mechanisms; (2) Transportation study - technical and economic feasibility of transporting and installing a wind turbine unit via a standard barge with minimal conversion and (3) Self-burial system study - to demonstrate the feasibility of self burial of a slab foundation via controlled jetting beneath the slab. The background to the study and the proposed concepts are discussed. The work carried out to date and the costs are reported together with the findings. Recommendations for future work are listed. The work was carried out by Corus UK Ltd and is managed by Future Energy Solutions for the DTI.

  18. Protection of Large-scale Wind Power Integration

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    More and more large capacity wind power will be integrated into power system in the future, and certain technical challenges will emerge due to the fluctuation characteristics of wind power and the complex control of power electronic devices inside the wind turbines (e. g., low voltage ride through (LVRT)). By comparing a wind power integration grid with a hydropower integration grid, the special transient phenomena caused by the wind power integration is studied and simulation results are presented. Furthermore, the potential impacts on the traditional protection are discussed. Results show that the special transient phenomena can decrease the sensitivity, reliability and operation speed of conventional protections.

  19. Grid integration impacts on wind turbine design and development

    DEFF Research Database (Denmark)

    Hansen, Anca Daniela; Cutululis, Nicolaos Antonio; Sørensen, Poul Ejnar;

    2009-01-01

    This paper presents an overall perspective on contemporary issues like wind power plants and grid integration. The purpose is to present and discuss the impacts of emerging new grid connection requirements on modern wind turbines. The grid integration issue has caused several new challenges to the...... wind turbine design and development. The survival of different wind turbine concepts and controls is strongly conditioned by their ability to comply with stringent grid connection requirements, imposed by utility companies. Beside its impact on the mechanical design and control of wind turbines, the...... grid integration aspect has also an effect on wind turbines' role in the power system, on wind turbine technologies' survival on the market, as well as on the wind turbines' loads. Over the last years, it became obviously, that there it is an increasing need for design and research of wind turbines...

  20. Nebraska Statewide Wind Integration Study: April 2008 - January 2010

    Energy Technology Data Exchange (ETDEWEB)

    EnerNex Corporation, Knoxville, Tennessee; Ventyx, Atlanta, Georgia; Nebraska Power Association, Lincoln, Nebraska

    2010-03-01

    Wind generation resources in Nebraska will play an increasingly important role in the environmental and energy security solutions for the state and the nation. In this context, the Nebraska Power Association conducted a state-wide wind integration study.

  1. An Energy Storage System Sizing Method for Wind Power Integration

    OpenAIRE

    Wei Wang(College of William and Mary); Chengxiong Mao; Jiming Lu; Dan Wang

    2013-01-01

    Combining an energy storage system (ESS) with a wind farm is an effective way to increase the penetration rate of wind power. ESS sizing is an important part in wind farm planning nowadays. In this paper, a basic method for determining the optimal capacity of an ESS integrated with a wind power generator to meet the requirements of grid integration is presented. With the proposed method, the necessary ESS capacity which can provide the best benefits between the regulation effects and energy s...

  2. System and market integration of wind power in Denmark

    DEFF Research Database (Denmark)

    Lund, Henrik; Hvelplund, Frede; Alberg Østergaard, Poul;

    2013-01-01

    Denmark has more than 10 years’ of experience with a wind share of approximately 20 per cent. During these 10 years, electricity markets have been subject to developments with a key focus on integrating wind power as well as trading electricity with neighbouring countries. This article introduces...... a methodology to analyse and understand the current market integration of wind power and concludes that the majority of Danish wind power in the period 2004e2008 was used to meet the domestic demand. Based on a physical analysis, at least 63 per cent of Danish wind power was used domestically in 2008....... To analyse the remaining 37 per cent, we must apply a market model to identify cause-effect relationships. The Danish case does not illustrate any upper limit for wind power integration, as also illustrated by Danish political targets to integrate 50 per cent by 2020. In recent years, Danish wind power has...

  3. CanWEA Pan-Canadian wind integration study paper

    Energy Technology Data Exchange (ETDEWEB)

    Tremblay, Martin [GL Garrad Hassan Canada Inc, Ottawa, ON (Canada); Gardner, Paul [GL Garrad Hassan and Partners, Glasgow (United Kingdom); Price, Doug; Le, Don [GL Garrad Hassan America, San Diego, CA (United States)

    2010-07-01

    GL Garrad Hassan has been contracted by CanWEA to undertake a scoping study for a future Pan-Canadian Wide-Scale Wind Integration Study. The scoping study provides the methodology and the rationale on which the actual wind integration study and request for proposals will be based on. Major system operators and owners of each Canadian Province along with experts involved in major US wind integration studies have been consulted and contributed to the decisional process. This paper provides a summary of the factors considered in the study and outline the actual methodology that was adopted for the future Pan-Canadian wind integration study. (orig.)

  4. Integrating Wind And Solar With Hydrogen Producing Fuel Cells

    NARCIS (Netherlands)

    Hemmes, K.

    2007-01-01

    The often proposed solution for the fluctuating wind energy supply is the conversion of the surplus of wind energy into hydrogen by means of electrolysis. In this paper a patented alternative is proposed consisting of the integration of wind turbines with internal reforming fuel-cells, capable of co

  5. Review of Energy Storage System for Wind Power Integration Support

    DEFF Research Database (Denmark)

    Zhao, Haoran; Wu, Qiuwei; Hu, Shuju;

    2015-01-01

    -discharging characteristics, Energy Storage System (ESS) is considered as an effective tool to enhance the flexibility and controllability not only of a specific wind farm, but also of the entire grid. This paper reviews the state of the art of the ESS technologies for wind power integration support from different aspects......With the rapid growth of wind energy development and increasing wind power penetration level, it will be a big challenge to operate the power system with high wind power penetration securely and reliably due to the inherent variability and uncertainty of wind power. With the flexible charging...

  6. WINS. Market Simulation Tool for Facilitating Wind Energy Integration

    Energy Technology Data Exchange (ETDEWEB)

    Shahidehpour, Mohammad [Illinois Inst. of Technology, Chicago, IL (United States)

    2012-10-30

    Integrating 20% or more wind energy into the system and transmitting large sums of wind energy over long distances will require a decision making capability that can handle very large scale power systems with tens of thousands of buses and lines. There is a need to explore innovative analytical and implementation solutions for continuing reliable operations with the most economical integration of additional wind energy in power systems. A number of wind integration solution paths involve the adoption of new operating policies, dynamic scheduling of wind power across interties, pooling integration services, and adopting new transmission scheduling practices. Such practices can be examined by the decision tool developed by this project. This project developed a very efficient decision tool called Wind INtegration Simulator (WINS) and applied WINS to facilitate wind energy integration studies. WINS focused on augmenting the existing power utility capabilities to support collaborative planning, analysis, and wind integration project implementations. WINS also had the capability of simulating energy storage facilities so that feasibility studies of integrated wind energy system applications can be performed for systems with high wind energy penetrations. The development of WINS represents a major expansion of a very efficient decision tool called POwer Market Simulator (POMS), which was developed by IIT and has been used extensively for power system studies for decades. Specifically, WINS provides the following superiorities; (1) An integrated framework is included in WINS for the comprehensive modeling of DC transmission configurations, including mono-pole, bi-pole, tri-pole, back-to-back, and multi-terminal connection, as well as AC/DC converter models including current source converters (CSC) and voltage source converters (VSC); (2) An existing shortcoming of traditional decision tools for wind integration is the limited availability of user interface, i.e., decision

  7. Operating Reserves and Wind Power Integration: An International Comparison; Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Milligan, M.; Donohoo, P.; Lew, D.; Ela, E.; Kirby, B.; Holttinen, H.; Lannoye, E.; Flynn, D.; O' Malley, M.; Miller, N.; Eriksen, P. B.; Gottig, A.; Rawn, B.; Gibescu, M.; Lazaro, E. G.; Robitaille, A.; Kamwa, I.

    2010-10-01

    This paper provides a high-level international comparison of methods and key results from both operating practice and integration analysis, based on an informal International Energy Agency Task 25: Large-scale Wind Integration.

  8. Wind power integration connection and system operational aspects

    CERN Document Server

    Fox, Brendan; Bryans, Leslie

    2007-01-01

    The rapid growth of wind power and the implications of this on future power system planning, operation and control has become an even greater challenge in today's liberalised electricity market conditions. This essential book examines the main problems of wind power integration and guides the reader through a number of the most recent solutions based on current research and operational experience of wind power integration.

  9. Power System Operation with Large Scale Wind Power Integration

    DEFF Research Database (Denmark)

    Suwannarat, A.; Bak-Jensen, B.; Chen, Z.;

    2007-01-01

    The Danish power system starts to face problems of integrating thousands megawatts of wind power, which produce in a stochastic behavior due to natural wind fluctuations. With wind power capacities increasing, the Danish Transmission System Operator (TSO) is faced with new challenges related to the...... uncertain nature of wind power. In this paper, proposed models of generations and control system are presented which analyze the deviation of power exchange at the western Danish-German border, taking into account the fluctuating nature of wind power. The performance of the secondary control of the thermal...

  10. Spatio-temporal data analytics for wind energy integration

    CERN Document Server

    Yang, Lei; Zhang, Junshan

    2014-01-01

    This SpringerBrief presents spatio-temporal data analytics for wind energy integration using stochastic modeling and optimization methods. It explores techniques for efficiently integrating renewable energy generation into bulk power grids. The operational challenges of wind, and its variability are carefully examined. A spatio-temporal analysis approach enables the authors to develop Markov-chain-based short-term forecasts of wind farm power generation. To deal with the wind ramp dynamics, a support vector machine enhanced Markov model is introduced. The stochastic optimization of economic di

  11. Integrated study of Mediterranean deep canyons: Novel results and future challenges

    Science.gov (United States)

    Canals, M.; Company, J. B.; Martín, D.; Sànchez-Vidal, A.; Ramírez-Llodrà, E.

    2013-11-01

    This volume compiles a number of scientific papers resulting from a sustained multidisciplinary research effort of the deep-sea ecosystem in the Mediterranean Sea. This started 20 years ago and peaked over the last few years thanks to a number of Spanish and European projects such as PROMETEO, DOS MARES, REDECO, GRACCIE, HERMES, HERMIONE and PERSEUS, amongst others. The geographic focus of most papers is on the NW Mediterranean Sea including the Western Gulf of Lion and the North Catalan margin, with a special attention to submarine canyons, in particular the Blanes and Cap de Creus canyons. This introductory article to the Progress in Oceanography special issue on “Mediterranean deep canyons” provides background information needed to better understand the individual papers forming the volume, comments previous reference papers related to the main topics here addressed, and finally highlights the existing relationships between atmospheric forcing, oceanographic processes, seafloor physiography, ecosystem response, and litter and chemical pollution. This article also aims at constituting a sort of glue, in terms of existing knowledge and concepts and novel findings, linking together the other twenty papers in the volume, also including some illustrative figures. The main driving ideas behind this special issue, particularly fitting to the study area of the NW Mediterranean Sea, could be summarized as follows: (i) the atmosphere and the deep-sea ecosystem are connected through oceanographic processes originating in the coastal area and the ocean surface, which get activated at the occasion of high-energy events leading to fast transfers of matter and energy to the deep; (ii) shelf indented submarine canyons play a pivotal role in such transfers, which involve dense water, sedimentary particles, organic matter, litter and chemical pollutants; (iii) lateral inputs (advection) from the upper continental margin contributes significantly to the formation of

  12. Generic 12-Bus Test System for Wind Power Integration Studies

    DEFF Research Database (Denmark)

    Adamczyk, Andrzej Grzegorz; Altin, Müfit; Göksu, Ömer;

    2012-01-01

    High wind power penetration levels into power systems requires an appropriate power system model when assessing impact on the overall system stability. The model should capture the wide range of dynamics related to the wind integration studies, such as voltage control, synchronizing power control...

  13. Integrated Bidding and Operating Strategies for Wind-Storage Systems

    DEFF Research Database (Denmark)

    Ding, Huajie; Pinson, Pierre; Hu, Zechun;

    2016-01-01

    Due to their flexible charging and discharging capabilities, energy storage systems (ESS) are considered a promising complement to wind farms (WFs) participating in electricity markets. This paper presents integrated day-ahead bidding and real-time operation strategies for a wind-storage system...

  14. Wind turbine generation systems modeling for integration in power systems

    OpenAIRE

    Junyent Ferré, Adrià; Gomis Bellmunt, Oriol

    2011-01-01

    This chapter deals with the modeling of wind turbine generation systems for integration in power systems studies. The modeling of the wind phenomenon, the turbine mechanical system and the electrical machine, along with the corresponding converter and electrical grid is described.

  15. Integrated analysis of wind turbines - The impact of power systems on wind turbine design

    DEFF Research Database (Denmark)

    Barahona Garzón, Braulio

    Megawatt-size wind turbines nowadays operate in very complex environmental conditions, and increasingly demanding power system requirements. Pursuing a cost-effective and reliable wind turbine design is a multidisciplinary task. However nowadays, wind turbine design and research areas...... system frequency control studies of variable-speed wind turbines with the integrated simulation environment, show that is possible to make a sensible estimation of the contribution of a wind farm to power system frequency control, while studying the impact on wind turbine structural loads. Finally......, studies of the impact that voltage faults have on wind turbine loads are presented. The case of unbalanced faults is addressed, the possibilities and drawbacks for reduction of structural loads using electrical control actions is investigated. Load reduction using resonant damping control is proven...

  16. Wind Integration Cost and Cost-Causation: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Milligan, M.; Kirby, B.; Holttinen, H.; Kiviluoma, J.; Estanqueiro, A.; Martin-Martinez, S.; Gomez-Lazaro, E.; Peneda, I.; Smith, C.

    2013-10-01

    The question of wind integration cost has received much attention in the past several years. The methodological challenges to calculating integration costs are discussed in this paper. There are other sources of integration cost unrelated to wind energy. A performance-based approach would be technology neutral, and would provide price signals for all technology types. However, it is difficult to correctly formulate such an approach. Determining what is and is not an integration cost is challenging. Another problem is the allocation of system costs to one source. Because of significant nonlinearities, this can prove to be impossible to determine in an accurate and objective way.

  17. The Western Wind and Solar Integration Study Phase 2

    Energy Technology Data Exchange (ETDEWEB)

    Lew, D.; Brinkman, G.; Ibanez, E.; Hodge, B. M.; Hummon, M.; Florita, A.; Heaney, M.

    2013-09-01

    The electric grid is a highly complex, interconnected machine, and changing one part of the grid can have consequences elsewhere. Adding wind and solar affects the operation of the other power plants and adding high penetrations can induce cycling of fossil-fueled generators. Cycling leads to wear-and-tear costs and changes in emissions. Phase 2 of the Western Wind and Solar Integration Study (WWSIS-2) evaluated these costs and emissions and simulated grid operations for a year to investigate the detailed impact of wind and solar on the fossil-fueled fleet. This built on Phase 1, one of the largest wind and solar integration studies ever conducted, which examined operational impacts of high wind and solar penetrations in the West.

  18. The Western Wind and Solar Integration Study Phase 2

    Energy Technology Data Exchange (ETDEWEB)

    Lew, Debra [National Renewable Energy Lab. (NREL), Golden, CO (United States); Brinkman, Greg [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ibanez, E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Florita, A. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Heaney, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Hodge, B. -M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Hummon, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Stark, G. [National Renewable Energy Lab. (NREL), Golden, CO (United States); King, J. [RePPAE; Lefton, S. A. [Intertek-APTECH, Houston, TX (United States); Kumar, N. [Intertek-APTECH, Houston, TX (United States); Agan, D. [Intertek-APTECH, Houston, TX (United States); Jordan, G. [GE Energy, Fairfield, CT (United States); Venkataraman, S. [GE Energy, Fairfield, CT (United States)

    2013-09-01

    The electric grid is a highly complex, interconnected machine, and changing one part of the grid can have consequences elsewhere. Adding wind and solar affects the operation of the other power plants and adding high penetrations can induce cycling of fossil-fueled generators. Cycling leads to wear-and-tear costs and changes in emissions. Phase 2 of the Western Wind and Solar Integration Study (WWSIS-2) evaluated these costs and emissions and simulated grid operations for a year to investigate the detailed impact of wind and solar on the fossil-fueled fleet. This built on Phase 1, one of the largest wind and solar integration studies ever conducted, which examined operational impacts of high wind and solar penetrations in the West(GE Energy 2010).

  19. Great Lakes Offshore Wind Project: Utility and Regional Integration Study

    Energy Technology Data Exchange (ETDEWEB)

    Loparo, Kenneth A.; Sajadi, Amir; D' Aquila, Robert; Clark, Kara; Waligorski, Joseph; Baker, Scott

    2016-06-30

    This project aims to identify transmission system upgrades needed to facilitate offshore wind projects as well as operational impacts of offshore generation on operation of the regional transmission system in the Great Lakes region. A simulation model of the US Eastern Interconnection was used as the test system as a case study for investigating the impact of the integration of a 1000MW offshore wind farm operating in Lake Erie into FirstEnergy/PJM service territory. The findings of this research provide recommendations on offshore wind integration scenarios, the locations of points of interconnection, wind profile modeling and simulation, and computational methods to quantify performance, along with operating changes and equipment upgrades needed to mitigate system performance issues introduced by an offshore wind project.

  20. Wind energy integration in the Spanish electrical system

    International Nuclear Information System (INIS)

    Integration of significant amounts of wind power in electrical systems represents a challenge for TSOs, due to the technological and distributed particularities of wind generators and to the variability of its primary resource. The proposed paper describes the implications of massive wind power integration in the Spanish system in terms of technical requirements and operation measures. Concerning technical specifications for wind producers, the former criteria are nowadays being reviewed and the new requirements under discussion right now (grid code) are here introduced. Stability studies for the horizon 2016 (about 29 GW of wind power installed) and beyond have been performed and the obtrained results for the considered scenarios have led to a series of necessary criteria which relate to the next topics: - increased fault ride-though capabilities, - voltage maintenance and support in static and dynamic, - restoration of primary regulation reserves to the system, - active power and ramp controlling. Innovative solutions for wind power control, already operative in Spain, such as the dedicated control centre for renewable energies and other special producers (CECRE) will still provide the necessary tools and infrastructure to optimise integration limits in real time, maximizing renewable energy production and assuring security, as well as the communication with the renewable control centres. Regarding system balancing, while currently being able to appropriately deliver demand coverage, the main concern is the dispacement by wind power of conventional generation that will be required shortly afterwards to cover peak demand. Further concerns are the need to keep appropriate sizing of downward reserves during off-peak hours. This is normally dealt with market mechanisms leading combined cycle units to daily shut-down and start-up. When wind forecast errors occur and wind production is higher than expected, the system may run out of downward reserve and combined cycle

  1. Wind Integration National Dataset (WIND) Toolkit; NREL (National Renewable Energy Laboratory)

    Energy Technology Data Exchange (ETDEWEB)

    Draxl, Caroline; Hodge, Bri-Mathias

    2015-07-14

    A webinar about the Wind Integration National Dataset (WIND) Toolkit was presented by Bri-Mathias Hodge and Caroline Draxl on July 14, 2015. It was hosted by the Southern Alliance for Clean Energy. The toolkit is a grid integration data set that contains meteorological and power data at a 5-minute resolution across the continental United States for 7 years and hourly power forecasts.

  2. Electric vehicles and large-scale integration of wind power

    DEFF Research Database (Denmark)

    Liu, Wen; Hu, Weihao; Lund, Henrik;

    2013-01-01

    with this imbalance and to reduce its high dependence on oil production. For this reason, it is interesting to analyse the extent to which transport electrification can further the renewable energy integration. This paper quantifies this issue in Inner Mongolia, where the share of wind power in the electricity supply...... was 6.5% in 2009 and which has the plan to develop large-scale wind power. The results show that electric vehicles (EVs) have the ability to balance the electricity demand and supply and to further the wind power integration. In the best case, the energy system with EV can increase wind power......Renewable energy is one of the possible solutions when addressing climate change. Today, large-scale renewable energy integration needs to include the experience to balance the discrepancy between electricity demand and supply. The electrification of transportation may have the potential to deal...

  3. Optimal integration of wind farms to isolated wind-Diesel energy system

    International Nuclear Information System (INIS)

    Wind farms installed on isolated systems are subject to significant restrictions, affecting their expected energy yield and, hence, the feasibility of investments. As wind power penetrations increase in isolated power systems, it is very important to understand how variations in wind plant outputs affect the operation of the isolated system on a day to day basis and what the associated added costs are. In this paper, a wind-Diesel coordination generation scheduling (WCGS) software is developed for appropriate assessment of the added cost to cover the unpredictable wind generator output variations. The developed WCGS software is also a useful tool for the system planner to predict the energy cost and the fuel saving from the expected new wind-Diesel systems. Several technique constraints are applied to determine the optimal proportion of wind generator capacity that can be integrated into the existing system. A simple benefit cost ratio (BCR) is used in this study to evaluate the investment effectiveness of the installation of wind farms for an isolated hybrid system. Numerical experiments are included to understand the wind generator output variations in system operating cost analysis and to assess the impact and economic benefits of the installation of wind farms

  4. Integration of large scale wind power

    Energy Technology Data Exchange (ETDEWEB)

    Davidsen, Troels [Inopower A/S (Denmark)

    2011-07-01

    Since 2006, the Danish TSO Energinet.dk, has got large power consumption systems available for balancing the power grid during large Wind Power in feed situations. In 2011 a total of 250 MW electro boilers are installed. The power for the electro boilers is traded on the Nordpool power exchange in the day a head market and the ancillary services markets. (orig.)

  5. The Whittard Canyon - A case study of submarine canyon processes

    Science.gov (United States)

    Amaro, T.; Huvenne, V. A. I.; Allcock, A. L.; Aslam, T.; Davies, J. S.; Danovaro, R.; De Stigter, H. C.; Duineveld, G. C. A.; Gambi, C.; Gooday, A. J.; Gunton, L. M.; Hall, R.; Howell, K. L.; Ingels, J.; Kiriakoulakis, K.; Kershaw, C. E.; Lavaleye, M. S. S.; Robert, K.; Stewart, H.; Van Rooij, D.; White, M.; Wilson, A. M.

    2016-08-01

    Submarine canyons are large geomorphological features that incise continental shelves and slopes around the world. They are often suggested to be biodiversity and biomass hotspots, although there is no consensus about this in the literature. Nevertheless, many canyons do host diverse faunal communities but owing to our lack of understanding of the processes shaping and driving this diversity, appropriate management strategies have yet to be developed. Here, we integrate all the current knowledge of one single system, the Whittard Canyon (Celtic Margin, NE Atlantic), including the latest research on its geology, sedimentology, geomorphology, oceanography, ecology, and biodiversity in order to address this issue. The Whittard Canyon is an active system in terms of sediment transport. The net suspended sediment transport is mainly up-canyon causing sedimentary overflow in some upper canyon areas. Occasionally sediment gravity flow events do occur, some possibly the result of anthropogenic activity. However, the role of these intermittent gravity flows in transferring labile organic matter to the deeper regions of the canyon appears to be limited. More likely, any labile organic matter flushed downslope in this way becomes strongly diluted with bulk material and is therefore of little food value for benthic fauna. Instead, the fresh organic matter found in the Whittard Channel mainly arrives through vertical deposition and lateral transport of phytoplankton blooms that occur in the area during spring and summer. The response of the Whittard Canyon fauna to these processes is different in different groups. Foraminiferal abundances are higher in the upper parts of the canyon and on the slope than in the lower canyon. Meiofaunal abundances in the upper and middle part of the canyon are higher than on adjacent slopes, but lower in the deepest part. Mega- and macrofauna abundances are higher in the canyon compared with the adjacent slope and are higher in the eastern than

  6. Permanent magnet machines with air gap windings and integrated teeth windings

    Energy Technology Data Exchange (ETDEWEB)

    Alatalo, M. [Chalmers Univ. of Technology, Goeteborg (Sweden). School of Electrical and Computer Engineering

    1996-06-01

    The Thesis deals with axial and radial flux permanent magnet machines with air gap windings and an integrated teeth winding. The aim is to develop a machine that produces a high torque per unit volume with as low losses as possible. The hypothesis is that an advanced three-phase winding, magnetized by a permanent magnet rotor should be better than other machine topologies. The finite element method is used to find favourable dimensions of the slotless winding, the integrated teeth winding and the permanent magnet rotor. Three machines were built and tested in order to verify calculations. It can be concluded that the analysis method shows good agreement with the calculated and the measured values of induced voltage and torque. The experiments showed that the slotless machine with NdFeB-magnets performs approximately like the slotted machine. A theoretical comparison of axial flux topology to radial flux topology showed that the torque production of the inner rotor radial flux machine is superior to that of the axial flux machine. An integrated teeth winding based on iron powder teeth glued to the winding was studied. The force density of a pole with integrated teeth is around three times the force density of a slotless pole. A direct drive wind power generator of 6.4 kW with integrated teeth can have the same power losses and magnet weight as a transversal flux machine. Compared to a standard induction machine the integrated teeth machine had approximately 2.5 times the power capacity of the induction machine with the same power losses and outer volume. 39 refs

  7. The marine soundscape of the Perth Canyon

    Science.gov (United States)

    Erbe, Christine; Verma, Arti; McCauley, Robert; Gavrilov, Alexander; Parnum, Iain

    2015-09-01

    The Perth Canyon is a submarine canyon off Rottnest Island in Western Australia. It is rich in biodiversity in general, and important as a feeding and resting ground for great whales on migration. Australia's Integrated Marine Observing System (IMOS) has moorings in the Perth Canyon monitoring its acoustical, physical and biological oceanography. Data from these moorings, as well as weather data from a near-by Bureau of Meteorology weather station on Rottnest Island and ship traffic data from the Australian Maritime Safety Authority were correlated to characterise and quantify the marine soundscape between 5 and 3000 Hz, consisting of its geophony, biophony and anthrophony. Overall, biological sources are a strong contributor to the soundscape at the IMOS site, with whales dominating seasonally at low (15-100 Hz) and mid frequencies (200-400 Hz), and fish or invertebrate choruses dominating at high frequencies (1800-2500 Hz) at night time throughout the year. Ships contribute significantly to the 8-100 Hz band at all times of the day, all year round, albeit for a few hours at a time only. Wind-dependent noise is significant at 200-3000 Hz; winter rains are audible underwater at 2000-3000 Hz. We discuss how passive acoustic data can be used as a proxy for ocean weather. Passive acoustics is an efficient way of monitoring animal visitation times and relative densities, and potential anthropogenic influences.

  8. Integrating Structural Health Management with Contingency Control for Wind Turbines

    Directory of Open Access Journals (Sweden)

    Kai Goebel

    2013-01-01

    Full Text Available Maximizing turbine up-time and reducing maintenance costs are key technology drivers for wind turbine operators. Components within wind turbines are subject to considerable stresses due to unpredictable environmental conditions resulting from rapidly changing local dynamics. In that context, systems health management has the aim to assess the state-of-health of components within a wind turbine, to estimate remaining life, and to aid in autonomous decision-making to minimize damage to the turbine. Advanced contingency control is one way to enable autonomous decision-making by providing the mechanism to enable safe and efficient turbine operation. The work reported herein explores the integration of condition monitoring of wind turbine blades with contingency control to balance the trade-offs between maintaining system health and energy capture. Results are demonstrated using a high fidelity simulator of a utility-scale wind turbine.

  9. An Energy Storage System Sizing Method for Wind Power Integration

    Directory of Open Access Journals (Sweden)

    Wei Wang

    2013-07-01

    Full Text Available Combining an energy storage system (ESS with a wind farm is an effective way to increase the penetration rate of wind power. ESS sizing is an important part in wind farm planning nowadays. In this paper, a basic method for determining the optimal capacity of an ESS integrated with a wind power generator to meet the requirements of grid integration is presented. With the proposed method, the necessary ESS capacity which can provide the best benefits between the regulation effects and energy storage size was calculated. The segmentation method and automatic segmentation method are proposed to improve the performance of the basic method. Further work on expanding the method to determine the necessary capacity of ESS for real-time control is studied. The time window method is used to enable the proposed method available under all working conditions. The simulation results verify the effectiveness of the proposed method.

  10. Trends in SCADA solutions applied to wind energy integration

    Energy Technology Data Exchange (ETDEWEB)

    Eichler, Roland [Siemens AG (Germany); Lorimer, Martin [Siemens Ltd. (United Kingdom); Romero Velazquez, Manuel [Siemens S.A. (Spain)

    2010-07-01

    Monitoring and control of wind parks - whether onshore or offshore - is done on three levels: at the first level a wind park SCADA deals with individual wind turbines, at an intermediate level SCADA oversees large wind parks or several smaller ones with their grid connection, and on the system operator level SCADA/EMS mainly addresses system stability. The paper focuses on SCADA solutions applied to the intermediate level. The goal of the paper is to identify different stages of wind park integration both from an organization/rules point of view and from a technical point of view. This is done on the basis of wind park projects in Europe. Besides others, the paper identifies technical trends in SCADA systems, system architecture, communication media, and communication protocols (incl. IEC 61850). Technical solutions applied, of course, reflect the organizational framework in the respective country/market. The paper identifies general requirements on SCADA solutions for wind energy integration that allow largely standardized solutions. This leads to faster and more economic solutions. An outlook includes standards not yet seen in grid level SCADA systems such as IEC 61400-25. (orig.)

  11. Integration of Wind Power into the Danish Power System

    DEFF Research Database (Denmark)

    Rácz, Viktor J.; Yadav, Priyadarshini; Vestergaard, Niels

    the price of electricity. We have observed the degree of influence of the fossil fuel prices, total demand, wind power production and import on the electricity price and the individual co-efficiency for the years 2000, 2005 and 2010, according to the energy mix. Using a grid management model for the Western......Wind energy is a major player in the Danish electricity market with an ambitious goal to pursue 50% of the electricity market by 2020. This paper examines the economic impacts of increasing integration of large-scale wind power to the existing electrical grid. Firstly, we survey the literature...

  12. Overview and Meteorological Validation of the Wind Integration National Dataset toolkit

    Energy Technology Data Exchange (ETDEWEB)

    Draxl, C. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hodge, B. M. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Clifton, A. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); McCaa, J. [3TIER by VAisala, Seattle, WA (United States)

    2015-04-13

    The Wind Integration National Dataset (WIND) Toolkit described in this report fulfills these requirements, and constitutes a state-of-the-art national wind resource data set covering the contiguous United States from 2007 to 2013 for use in a variety of next-generation wind integration analyses and wind power planning. The toolkit is a wind resource data set, wind forecast data set, and wind power production and forecast data set derived from the Weather Research and Forecasting (WRF) numerical weather prediction model. WIND Toolkit data are available online for over 116,000 land-based and 10,000 offshore sites representing existing and potential wind facilities.

  13. IEA Wind Task 24 Integration of Wind and Hydropower Systems; Volume 2: Participant Case Studies

    Energy Technology Data Exchange (ETDEWEB)

    Acker, T.

    2011-12-01

    This report describes the background, concepts, issues and conclusions related to the feasibility of integrating wind and hydropower, as investigated by the members of IEA Wind Task 24. It is the result of a four-year effort involving seven IEA member countries and thirteen participating organizations. The companion report, Volume 2, describes in detail the study methodologies and participant case studies, and exists as a reference for this report.

  14. The effects of different regulation strategies on Jiangsu's wind integration

    DEFF Research Database (Denmark)

    Hong, Lixuan; Lund, Henrik; Möller, Bernd;

    This paper presents the influence of different regulation strategies on wind energy integration into existing Jiangsu’s energy system. The ability of wind integration is defined in terms of the ability to avoid excess electricity production, to conserve primary energy consumptions and to reduce CO2...... emissions in the system. Firstly, a reference model of Jiangsu’s energy system is built by using EnergyPLAN based on the year 2009. The model results then are compared to actual values from 2009 to validate its accuracy. Based on the reference model, different regulations of Jiangsu’s energy system are...

  15. Integrated simulation challenges with the DeepWind floating vertical axis wind turbine concept

    DEFF Research Database (Denmark)

    Verelst, David; Aagaard Madsen, Helge; Borg, Michael;

    2015-01-01

    This paper presents the experiences and challenges with concurrently carrying out numerical model development, integrated simulations and design of a novel floating vertical axis wind turbine, the DeepWind concept. The floating VAWT modelling capabilities of the aero-hydro-elastic HAWC2 simulation...... tool are briefly described and the design approach adopted for such a challenging project was to independently design subsystems in parallel, apart from essential design specifications. Instability issues encountered when integrating all subsystems in the unified numerical model, in particular blade...

  16. Large Scale Wind and Solar Integration in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Ernst, Bernhard; Schreirer, Uwe; Berster, Frank; Pease, John; Scholz, Cristian; Erbring, Hans-Peter; Schlunke, Stephan; Makarov, Yuri V.

    2010-02-28

    This report provides key information concerning the German experience with integrating of 25 gigawatts of wind and 7 gigawatts of solar power capacity and mitigating its impacts on the electric power system. The report has been prepared based on information provided by the Amprion GmbH and 50Hertz Transmission GmbH managers and engineers to the Bonneville Power Administration (BPA) and Pacific Northwest National Laboratory representatives during their visit to Germany in October 2009. The trip and this report have been sponsored by the BPA Technology Innovation office. Learning from the German experience could help the Bonneville Power Administration engineers to compare and evaluate potential new solutions for managing higher penetrations of wind energy resources in their control area. A broader dissemination of this experience will benefit wind and solar resource integration efforts in the United States.

  17. Methodologies for Wind Turbine and STATCOM Integration in Wind Power Plant Models for Harmonic Resonances Assessment

    DEFF Research Database (Denmark)

    Freijedo Fernandez, Francisco Daniel; Chaudhary, Sanjay Kumar; Guerrero, Josep M.;

    2015-01-01

    This paper approaches modelling methodologies for integration of wind turbines and STATCOM in harmonic resonance studies. Firstly, an admittance equivalent model representing the harmonic signature of grid connected voltage source converters is provided. A simplified type IV wind turbine modelling...... is then straightforward. This linear modelling is suitable to represent the wind turbine in the range of frequencies at which harmonic interactions are likely. Even the admittance method is suitable both for frequency and time domain studies, some limitations arise in practice when implementing it in...... the time-domain. As an alternative, a power based averaged modelling is also proposed. Type IV wind turbine harmonic signature and STATCOM active harmonic mitigation are considered for the simulation case studies. Simulation results provide a good insight of the features and limitations of the...

  18. An Appropriate Wind Model for Wind Integrated Power Systems Reliability Evaluation Considering Wind Speed Correlations

    OpenAIRE

    Rajesh Karki; Dinesh Dhungana; Roy Billinton

    2013-01-01

    Adverse environmental impacts of carbon emissions are causing increasing concerns to the general public throughout the world. Electric energy generation from conventional energy sources is considered to be a major contributor to these harmful emissions. High emphasis is therefore being given to green alternatives of energy, such as wind and solar. Wind energy is being perceived as a promising alternative. This source of energy technology and its applications have undergone significant researc...

  19. Western Wind and Solar Integration Study: Hydropower Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Acker, T.; Pete, C.

    2012-03-01

    The U.S. Department of Energy's (DOE) study of 20% Wind Energy by 2030 was conducted to consider the benefits, challenges, and costs associated with sourcing 20% of U.S. energy consumption from wind power by 2030. This study found that with proactive measures, no insurmountable barriers were identified to meet the 20% goal. Following this study, DOE and the National Renewable Energy Laboratory (NREL) conducted two more studies: the Eastern Wind Integration and Transmission Study (EWITS) covering the eastern portion of the U.S., and the Western Wind and Solar Integration Study (WWSIS) covering the western portion of the United States. The WWSIS was conducted by NREL and research partner General Electric (GE) in order to provide insight into the costs, technical or physical barriers, and operational impacts caused by the variability and uncertainty of wind, photovoltaic, and concentrated solar power when employed to serve up to 35% of the load energy in the WestConnect region (Arizona, Colorado, Nevada, New Mexico, and Wyoming). WestConnect is composed of several utility companies working collaboratively to assess stakeholder and market needs to and develop cost-effective improvements to the western wholesale electricity market. Participants include the Arizona Public Service, El Paso Electric Company, NV Energy, Public Service of New Mexico, Salt River Project, Tri-State Generation and Transmission Cooperative, Tucson Electric Power, Xcel Energy and the Western Area Power Administration.

  20. Introducing WISDEM:An Integrated System Modeling for Wind Turbines and Plant (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Dykes, K.; Graf, P.; Scott, G.; Ning, A.; King, R.; Guo, Y.; Parsons, T.; Damiani, R.; Felker, F.; Veers, P.

    2015-01-01

    The National Wind Technology Center wind energy systems engineering initiative has developed an analysis platform to leverage its research capabilities toward integrating wind energy engineering and cost models across wind plants. This Wind-Plant Integrated System Design & Engineering Model (WISDEM) platform captures the important interactions between various subsystems to achieve a better National Wind Technology Center wind energy systems engineering initiative has developed an analysis platform to leverage its research capabilities toward integrating wind energy engineering and cost models across wind plants. This Wind-Plant Integrated System Design & Engineering Model (WISDEM) platform captures the important interactions between various subsystems to achieve a better understanding of how to improve system-level performance and achieve system-level cost reductions. This work illustrates a few case studies with WISDEM that focus on the design and analysis of wind turbines and plants at different system levels.

  1. IEA Wind Task 24 Integration of Wind and Hydropower Systems; Volume 1: Issues, Impacts, and Economics of Wind and Hydropower Integration

    Energy Technology Data Exchange (ETDEWEB)

    Acker, T.

    2011-12-01

    This report describes the background, concepts, issues and conclusions related to the feasibility of integrating wind and hydropower, as investigated by the members of IEA Wind Task 24. It is the result of a four-year effort involving seven IEA member countries and thirteen participating organizations. The companion report, Volume 2, describes in detail the study methodologies and participant case studies, and exists as a reference for this report.

  2. TRAFFIC EMISSION TRANSPORTATION IN STREET CANYONS

    Institute of Scientific and Technical Information of China (English)

    XIE Xiao-min; WANG Jia-song; HUANG Zhen

    2009-01-01

    Spatial distributions of traffic-related pollutants in street canyons were investigated by field measurements and Computational Fluid Dynamics(CFD).Two typical street canyons were selected for field monitoring,and a three-dimensional numerical model was built based on Reynolds-averaged Navier-Stokes equations equipped with the standard k-ε turbulence models for CFD simulations.The study shows that the pollutant concentrations of vehicle emission correlate well with the traffic volume variation,wind direction and wind speed.The wind direction and speed at the roof level determine overwhellmingly the flow field and the distributions of pollutant concentrations in the street canyon.When the wind speed is equal to zero,the pollutant concentrations on the breath height of the both sides of the street canyon are almost the same.When the wind direction is perpendicular to the street,one main vortex is formed with a shape depending on the building structure on both sides of the street,the pollutant is accumulated on the leeward side,and the pollutant concentrations at the breath height on the leeward side are 2 to 3 times as those at the breath height on the windward side.If the wind direction makes some angles with the street canyon,the pollutant concentration will be higher on the leeward side because one main vortex will also be formed in the vertical section of the canyon by the perpendicular component of the wind.But pollutant concentrations decrease in the canyon because pollutants are dispersed along the axis of the street.Pollutants at different heights of the vertical section decrease with height,i.e.there are concentration gradients in the vertical section,and the pollutant concentrations on the leeward side of the upstream building are much higher than those on the windward side of the downstream building.

  3. Ventilation Processes in a Three-Dimensional Street Canyon

    Science.gov (United States)

    Nosek, Štěpán; Kukačka, Libor; Kellnerová, Radka; Jurčáková, Klára; Jaňour, Zbyněk

    2016-05-01

    The ventilation processes in three different street canyons of variable roof geometry were investigated in a wind tunnel using a ground-level line source. All three street canyons were part of an urban-type array formed by courtyard-type buildings with pitched roofs. A constant roof height was used in the first case, while a variable roof height along the leeward or windward walls was simulated in the two other cases. All street-canyon models were exposed to a neutrally stratified flow with two approaching wind directions, perpendicular and oblique. The complexity of the flow and dispersion within the canyons of variable roof height was demonstrated for both wind directions. The relative pollutant removals and spatially-averaged concentrations within the canyons revealed that the model with constant roof height has higher re-emissions than models with variable roof heights. The nomenclature for the ventilation processes according to quadrant analysis of the pollutant flux was introduced. The venting of polluted air (positive fluctuations of both concentration and velocity) from the canyon increased when the wind direction changed from perpendicular to oblique, irrespective of the studied canyon model. Strong correlations (>0.5) between coherent structures and ventilation processes were found at roof level, irrespective of the canyon model and wind direction. This supports the idea that sweep and ejection events of momentum bring clean air in and detrain the polluted air from the street canyon, respectively.

  4. TradeWind. Integrating wind. Developing Europe's power market for the large-scale integration of wind power. Final report

    Energy Technology Data Exchange (ETDEWEB)

    2009-02-15

    Based on a single European grid and power market system, the TradeWind project explores to what extent large-scale wind power integration challenges could be addressed by reinforcing interconnections between Member States in Europe. Additionally, the project looks at the conditions required for a sound power market design that ensures a cost-effective integration of wind power at EU level. In this way, the study addresses two issues of key importance for the future integration of renewable energy, namely the weak interconnectivity levels between control zones and the inflexibility and fragmented nature of the European power market. Work on critical transmission paths and interconnectors is slow for a variety of reasons including planning and administrative barriers, lack of public acceptance, insufficient economic incentives for TSOs, and the lack of a joint European approach by the key stakeholders. (au)

  5. Unit commitment with wind power generation: integrating wind forecast uncertainty and stochastic programming.

    Energy Technology Data Exchange (ETDEWEB)

    Constantinescu, E. M.; Zavala, V. M.; Rocklin, M.; Lee, S.; Anitescu, M. (Mathematics and Computer Science); (Univ. of Chicago); (New York Univ.)

    2009-10-09

    We present a computational framework for integrating the state-of-the-art Weather Research and Forecasting (WRF) model in stochastic unit commitment/energy dispatch formulations that account for wind power uncertainty. We first enhance the WRF model with adjoint sensitivity analysis capabilities and a sampling technique implemented in a distributed-memory parallel computing architecture. We use these capabilities through an ensemble approach to model the uncertainty of the forecast errors. The wind power realizations are exploited through a closed-loop stochastic unit commitment/energy dispatch formulation. We discuss computational issues arising in the implementation of the framework. In addition, we validate the framework using real wind speed data obtained from a set of meteorological stations. We also build a simulated power system to demonstrate the developments.

  6. Investigation on the integral output power model of a large-scale wind farm

    Institute of Scientific and Technical Information of China (English)

    BAO Nengsheng; MA Xiuqian; NI Weidou

    2007-01-01

    The integral output power model of a large-scale wind farm is needed when estimating the wind farm's output over a period of time in the future.The actual wind speed power model and calculation method of a wind farm made up of many wind turbine units are discussed.After analyzing the incoming wind flow characteristics and their energy distributions,and after considering the multi-effects among the wind turbine units and certain assumptions,the incoming wind flow model of multi-units is built.The calculation algorithms and steps of the integral output power model of a large-scale wind farm are provided.Finally,an actual power output of the wind farm is calculated and analyzed by using the practical measurement wind speed data.The characteristics of a large-scale wind farm are also discussed.

  7. Traffic contribution to air pollution in urban street canyons: Integrated application of the OSPM, moss biomonitoring and spectral analysis

    Science.gov (United States)

    Lazić, Lazar; Urošević, Mira Aničić; Mijić, Zoran; Vuković, Gordana; Ilić, Luka

    2016-09-01

    To investigate the air pollutant distribution within the ambient of urban street canyon, Operational Street Pollution Model (OSPM) was used to predict hourly content of NOX, NO, NO2, O3, CO, BNZ and PM10. The study was performed in five street canyons in Belgrade (Serbia) during 10-week summer period. The model receptors were located on each side of street canyons at 4 m, 8 m and 16 m height. To monitor airborne trace element content, the moss bag biomonitors were simultaneously exposed with the model receptors at two heights-4 m and 16 m. The results of both methods, modelling and biomonitoring, showed significantly decreasing trend of the air pollutants with height. The results indirectly demonstrate that biomonitoring, i.e., moss bag technique could be a valuable tool to verify model performance. In addition, spectral analysis was applied to investigate weekly variation of the daily background and modelled data set. Typical periodicities and weekend effect, caused by anthropogenic influences, have been identified.

  8. AC-DC integrated load flow calculation for variable speed offshore wind farms

    DEFF Research Database (Denmark)

    Zhao, Menghua; Chen, Zhe; Blaabjerg, Frede

    2005-01-01

    This paper proposes a sequential AC-DC integrated load flow algorithm for variable speed offshore wind farms. In this algorithm, the variable frequency and the control strategy of variable speed wind turbine systems are considered. In addition, the losses of wind turbine systems and the losses...... of converters are also integrated into the load flow algorithm. As a general algorithm, it can be applied to different types of wind farm configurations, and the load flow is related to the wind speed....

  9. Technologies for integrating wind farms to the grid. (Interim Report)

    Energy Technology Data Exchange (ETDEWEB)

    Chondrogiannis, Stamatios; Barnes, Mike [Univ. of Manchester, Manchester (United Kingdom); Aten, M [AREVA T and D Technology Centre, Paris, (France)

    2006-02-28

    This report discusses possible technologies for enabling the integration of wind farms into the power supply network. The capabilities of each technology in complying with the requirements set by the Grid Code are analysed. Subsequent reports associated with this project will establish the effect of a STATCOM to enable a grid connection of wind farms to the National Grid power supply network. To illustrate the technical challenges of integrating large wind farms into the network, an analysis of the GB Grid Code was carried out with particular attention paid to: Voltage control; Fault ride through capability; Fault current contribution; Frequency control. The main three wind generation technologies reviewed were: Doubly Fed Induction Generators (DFIGs); Fixed Speed Induction Generators (FSIGs); Direct drive synchronous generators through back-to-back voltage source converters. The four technical architectures for the connection of offshore wind farms to the power supply network reviewed were: AC connection; AC connection along with employment of Dynamic Reactive Compensation devices; Voltage Source (VS) HVDC link; and Line Commutated (LC) HVDC link. The GB Grid Code requirements apply to the whole wind farm as seen at the Point of Connection (PoC) rather than at the turbine terminals. Finally, this report provides an overview of the current state-of-the-art modelling techniques used for various components of a wind farm. Generic models of a DFIG, a FSIG generator and a STATCOM device are shown through simulation in the PSCAD/EMTDC software modelling package. Findings were that for cases of wind farms connected through AC submarine cables, without a supplementary reactive compensation device, the performance at the PoC depends mainly on the employed wind turbine generator technology. If a dynamic reactive compensation device is used, then this complementary technology has the potential to enhance the behaviour of the wind farm, especially for fault ride

  10. Experience analyzing wind data for large-scale integration

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Zhi; Dai, RenChang; Freeman, Lavelle A.; Miller, Nicholas W.; Shao, Miaolei [GEe Energy Consulting Group, Schenectady, NY (United States)

    2010-07-01

    Wind is a major piece of the green energy effort, and will certainly play a more important role in the future power industry. GE Energy has conducted a numer of large-scale renewable integration studies in North America. The objective of these studies is to understand how integrating large amounts of variable energy resources into the supply mix affects grid operation and economics. As part of this effort, various statistical analyses were performed to characterize the variability and uncertainty of wind generation. Based on the results of this characterization, further engineering and economic studies are performed to assess operational requirements, costs, and savings attributable to wind resources. For these analyses, a large amount of input data is usually required, and is often obtained in different formats. These data sets are not very intuitive at first glance, and need extensive effort to be developed into something informative. Based on project experience, different methods have been developed to explore and extrapolate the information hidden within large amounts of raw data. Algorithms and macros have been written to validate and correct data, to create summary information, and to produce derived data sets for further analyses. Informative plots and charts have also been programmed into various applications to provide quick, useful analysis when needed. This article introduces some illustrative and easy-to-analyze ways to look at these data using readily available tools. (orig.)

  11. Generation Expansion Planning Considering Integrating Large-scale Wind Generation

    DEFF Research Database (Denmark)

    Zhang, Chunyu; Ding, Yi; Østergaard, Jacob;

    2013-01-01

    necessitated the inclusion of more innovative and sophisticated approaches in power system investment planning. A bi-level generation expansion planning approach considering large-scale wind generation was proposed in this paper. The first phase is investment decision, while the second phase is production......Generation expansion planning (GEP) is the problem of finding the optimal strategy to plan the Construction of new generation while satisfying technical and economical constraints. In the deregulated and competitive environment, large-scale integration of wind generation (WG) in power system has...... optimization decision. A multi-objective PSO (MOPSO) algorithm was introduced to solve this optimization problem, which can accelerate the convergence and guarantee the diversity of Pareto-optimal front set as well. The feasibility and effectiveness of the proposed bi-level planning approach and the MOPSO...

  12. Nomograms for calculating pollution within street canyons

    Science.gov (United States)

    Buckland, A. T.; Middleton, D. R.

    The Environment Act 1995 has introduced the notion of local air quality management which requires that air quality in towns be reviewed and assessed. There is a need to identify those streets that are worst affected by vehicular pollutants. Such worst cases are likely to be narrow congested streets with tall buildings on each side. A nomogram presented here allows rapid screening of pollution in congested street canyons. The strong dependence on wind direction is reduced to the two extremes, namely wind along and wind across the canyon. Then canyon concentrations are estimated according to street geometry and traffic flow. The nomogram is designed for use by local authorities, is quick and easy to use, and paper or computer versions are available. It is suggested that detailed monitoring or modelling may only be required when simple screening methods predict high air pollution.

  13. Integrated municipal wind power concepts; Windenergienutzung im staedtischen Verbund

    Energy Technology Data Exchange (ETDEWEB)

    Kolbert, D.; Richert, F. [Ventis Energietechnik GmbH, Braunschweig (Germany)

    1998-06-01

    The role of wind power in the industrial sector currently depends very much on its technical and economic integrability in existing conventional supply structures. The most important questions in this context relate to capacity effects, adapted operating methods of conventional power suppliers, and, most important of all, operational energy production costs. In some regions alternative energy supply concepts are not yet or not sufficiently available. However, these will nevertheless offer ways of installing energy systems with a large renewable segment. The chances of bringing such projects to fruition depend for one thing on the climate, which may either stimulate or deter from development work on renewables (wind power, solar energy), and for another, often in apparent opposition to the former, on the oftentimes poorly developed infrastructure and economic strength of the region in question. [Deutsch] Die Bedeutung der Windenergienutzung im industrialisierten Bereich ist derzeit verknuepft mit deren technischen und oekonomischen Integrationsfaehigkeit in bestehende, konventionelle Versorgungsstrukturen. Im Vordergrund steht hierbei die Klaerung der Fragestellungen nach Kapazitaetseffekten, angepassten Betriebsweisen konventioneller Stromerzeuger und, in erster Linie, betriebswirtschaftlichen Energieerzeugungskosten. Derzeit bieten die Regionen, in denen eine anderweitige Versorgung noch nicht oder in nicht ausreichendem Masse existieren Moeglichkeiten zur Installation von Energiesystemen mit hoher regenerativer Durchdringung. Fuer die Realisation solcher Projekte stehen sich haeufig die klimatischen Bedingungen, die einerseits z.T. die Ursache fuer den geringen Entwicklungsstand sind, andererseits aber auch guenstige Voraussetzungen fuer die Nutzung regenerativer Energien (Wind, Sonne) bieten, der meist schlechten Infrastruktur und der geringen Wirtschaftskraft gegenueber. (orig./MSK)

  14. Hawaii Utility Integration Initiatives to Enable Wind (Wind HUI) Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Dora Nakafuji; Lisa Dangelmaier; Chris Reynolds

    2012-07-15

    To advance the state and nation toward clean energy, Hawaii is pursuing an aggressive Renewable Portfolio Standard (RPS), 40% renewable generation and 30% energy efficiency and transportation initiatives by 2030. Additionally, with support from federal, state and industry leadership, the Hawaii Clean Energy Initiative (HCEI) is focused on reducing Hawaii's carbon footprint and global warming impacts. To keep pace with the policy momentum and changing industry technologies, the Hawaiian Electric Companies are proactively pursuing a number of potential system upgrade initiatives to better manage variable resources like wind, solar and demand-side and distributed generation alternatives (i.e. DSM, DG). As variable technologies will continue to play a significant role in powering the future grid, practical strategies for utility integration are needed. Hawaiian utilities are already contending with some of the highest penetrations of renewables in the nation in both large-scale and distributed technologies. With island grids supporting a diverse renewable generation portfolio at penetration levels surpassing 40%, the Hawaiian utilities experiences can offer unique perspective on practical integration strategies. Efforts pursued in this industry and federal collaborative project tackled challenging issues facing the electric power industry around the world. Based on interactions with a number of western utilities and building on decades of national and international renewable integration experiences, three priority initiatives were targeted by Hawaiian utilities to accelerate integration and management of variable renewables for the islands. The three initiatives included: Initiative 1: Enabling reliable, real-time wind forecasting for operations by improving short-term wind forecasting and ramp event modeling capabilities with local site, field monitoring; Initiative 2: Improving operators situational awareness to variable resources via real-time grid condition

  15. Empirical Analysis of the Variability of Wind Generation in India: Implications for Grid Integration

    OpenAIRE

    Phadke, Amol

    2014-01-01

    We analyze variability in load and wind generation in India to assess its implications for grid integration of large scale wind projects using actual wind generation and load data from two states in India, Karnataka and Tamil Nadu. We compare the largest variations in load and net load (load ?wind, i.e., load after integrating wind) that the generation fleet has to meet. In Tamil Nadu, where wind capacity is about 53percent of the peak demand, we find that the additional variation added due t...

  16. Wind power integration into the automatic generation control of power systems with large-scale wind power

    DEFF Research Database (Denmark)

    Basit, Abdul; Hansen, Anca Daniela; Altin, Müfit;

    2014-01-01

    Transmission system operators have an increased interest in the active participation of wind power plants (WPP) in the power balance control of power systems with large wind power penetration. The emphasis in this study is on the integration of WPPs into the automatic generation control (AGC...

  17. Street canyon ventilation and atmospheric turbulence

    Science.gov (United States)

    Salizzoni, P.; Soulhac, L.; Mejean, P.

    Operational models for pollutant dispersion in urban areas require an estimate of the turbulent transfer between the street canyons and the overlying atmospheric flow. To date, the mechanisms that govern this process remain poorly understood. We have studied the mass exchange between a street canyon and the atmospheric flow above it by means of wind tunnel experiments. Fluid velocities were measured with a Particle Image Velocimetry system and passive scalar concentrations were measured using a Flame Ionisation Detector. The mass-transfer velocity between the canyon and the external flow has been estimated by measuring the cavity wash-out time. A two-box model, used to estimate the transfer velocity for varying dynamical conditions of the external flow, has been used to interpret the experimental data. This study sheds new light on the mechanisms which drive the ventilation of a street canyon and illustrates the influence of the external turbulence on the transfer process.

  18. Integrated analysis of well logs and seismic data to estimate gas hydrate concentrations at Keathley Canyon, Gulf of Mexico

    Science.gov (United States)

    Lee, M.W.; Collett, T.S.

    2008-01-01

    Accurately detecting and quantifying gas hydrate or free gas in sediments from seismic data require downhole well-log data to calibrate the physical properties of the gas hydrate-/free gas-bearing sediments. As part of the Gulf of Mexico Joint Industry Program, a series of wells were either cored or drilled in the Gulf of Mexico to characterize the physical properties of gas hydrate-bearing sediments, to calibrate geophysical estimates, and to evaluate source and transport mechanisms for gas within the gas hydrates. Downhole acoustic logs were used sparingly in this study because of degraded log quality due to adverse wellbore conditions. However, reliable logging while drilling (LWD) electrical resistivity and porosity logs were obtained. To tie the well-log information to the available 3-D seismic data in this area, a velocity log was calculated from the available resistivity log at the Keathley Canyon 151-2 well, because the acoustic log or vertical seismic data acquired at the nearby Keathley Canyon 151-3 well were either of poor quality or had limited depth coverage. Based on the gas hydrate saturations estimated from the LWD resistivity log, the modified Biot-Gassmann theory was used to generate synthetic acoustic log and a synthetic seismogram was generated with a fairly good agreement with a seismic profile crossing the well site. Based on the well-log information, a faintly defined bottom-simulating reflection (BSR) in this area is interpreted as a reflection representing gas hydrate-bearing sediments with about 15% saturation overlying partially gas-saturated sediments with 3% saturation. Gas hydrate saturations over 30-40% are estimated from the resistivity log in two distinct intervals at 220-230 and 264-300 m below the sea floor, but gas hydrate was not physically recovered in cores. It is speculated that the poor recovery of cores and gas hydrate morphology are responsible for the lack of physical gas hydrate recovery.

  19. Research on Aerodynamic Performance of High-speed Train through Canyon Wind Zone%高速列车通过峡谷风区时气动性能研究

    Institute of Scientific and Technical Information of China (English)

    牛纪强; 周丹; 李志伟; 杨明智

    2014-01-01

    On the basis of the three-dimensional unsteady compressible Reynolds-averaged N-S equation and the RNG κ-εequation turbulence model , the aerodynamic performance of the 8-vehicle high-speed train running in-to-out of a tunnel under canyon winds was simutaled ,and the wind velocities along the railway line were moni-tored . The computational results show as follows :The numerical simulation results are consistent with those of wind tunnel tests ;due to the influence of narrow passage effect and valley terrain , the wind velocity distri-bution on a bridge is asymmetric ;the difference between aerodynamic force changes of the train entering into the canyon and those of the train running out of the canyon is significant ;as the train is running at a high-speed on the railway line in the canyon wind zone , the aerodynamic forces and moment coefficents of the train are fluctua-ted obviously due to the gorge wind ;out of the fluctuated changes , the changes of the tail vehicle lateral force coeffi-cient and the head vehicle lift force coefficient are the largest , reaching 67% and 216% respectively .%基于三维非定常可压缩雷诺时均 N-S方程和RNG κ-ε双方程湍流模型,采用滑移网格技术,对峡谷风作用下8车编组的高速列车进出隧道气动性能进行模拟,并对沿线风速进行监测。研究表明:列车平地上非定常数值计算所得气动力系数均方根与风洞试验结果规律一致,两者吻合较好。由于受狭道效应和峡谷中地形地貌的共同作用影响,桥上各监测点的风速呈非对称分布。列车从隧道中驶入峡谷风区和从风区驶入隧道中两过程,列车气动力系数变化有明显差别。列车在峡谷风区高速行驶过程中,列车气动力及力矩系数会因受到以峡谷风为主的地形风影响而出现明显波动,其中尾车侧向力系数和头车升力系数受影响变化最大,分别为67%和216%。

  20. Overview of the New England wind integration. Study and selected results

    Energy Technology Data Exchange (ETDEWEB)

    Norden, John R.; Henson, William L.W. [ISO New England, Holyoke, MA (United States)

    2010-07-01

    ISO New England commissioned a comprehensive wind integration study to be completed in the early fall of 2010: the New England Wind Integration Study (NEWIS). The NEWIS assesses the efects of scenarios that encompass a range of wind-power penetrations in New England using statistical and simulation analysis including the development of a mesoscale wind-to-power model for the New England and Maritime wind resources areas. It also determines the impacts of integrating increasing amounts of wind generation resources for New England, as well as, the measures that may be available to the ISO for responding to any challenges while enabling the integration of wind-power. This paper provides an overview of the study then focuses on selected near final results, particularly with regard to the varying capacity factor, capacity value and siting that were determined as part of the study. The full results of the NEWIS will be released in the fall of 2010. (orig.)

  1. Integrating wind output with bulk power operations and wholesale electricity markets

    International Nuclear Information System (INIS)

    Wind farms have three characteristics that complicate their widespread application as an electricity resource: limited control, unpredictability and variability. Therefore the integration of wind output into bulk power electric systems is qualitatively different from that of other types of generators. The electric system operator must move other generators up or down to offset the time-varying wind fluctuations. Such movements raise the costs of fuel and maintenance for these other generators. Not only is wind power different, it is new. The operators of bulk power systems have limited experience in integrating wind output into the larger system. As a consequence, market rules that treat wind fairly - neither subsidizing nor penalizing its operation - have not yet been developed. The lack of data and analytical methods encourages wind advocates and sceptics to rely primarily on their biases and beliefs in suggesting how wind should be integrated into bulk power systems. This project helps fill this data and analysis gap. Specifically, it develops and applies a quantitative method for the integration of a wind resource into a large electric system. The method permits wind to bid its output into a short-term forward market (specifically, an hour-ahead energy market) or to appear in real time and accept only intrahour and hourly imbalance payments for the unscheduled energy it delivers to the system. Finally, the method analyses the short-term (minute-to-minute) variation in wind output to determine the regulation requirement the wind resource imposes on the electrical system. (author)

  2. Integrated airfoil and blade design method for large wind turbines

    DEFF Research Database (Denmark)

    Zhu, Wei Jun; Shen, Wen Zhong; Sørensen, Jens Nørkær

    2014-01-01

    and a free-stream Mach number of 0.25 near the tip. Results show that the new airfoils achieve a high power coefficient in a wide range of angles of attack (AOA) and are extremely insensitive to surface roughness. Finally, a full blade analysis using computational fluid dynamics (CFD) and blade element......This paper presents an integrated method for designing airfoil families of large wind turbine blades. For a given rotor diameter and a tip speed ratio, optimal airfoils are designed based on the local speed ratios. To achieve a high power performance at low cost, the airfoils are designed...... with the objectives of high Cp and small chord length. When the airfoils are obtained, the optimum flow angle and rotor solidity are calculated which forms the basic input to the blade design. The new airfoils are designed based on a previous in-house designed airfoil family which was optimized at a Reynolds number...

  3. Integration of a wind farm with a wave- and an aquaculture farm

    OpenAIRE

    He, J.; Weissenberger, J; Bergh, Øivind; Hjøllo, Solfrid Sætre; Wehde, Henning; Agnalt, Ann-Lisbeth; Chen, Z.; Olason, D.; Thorsteinson, B.; Fosso, O.B.

    2011-01-01

    There is a growing interest in placing wind farms offshore. 140 GW of offshore wind are currently being planned to reach the EU energy 2020 goal. However, an offshore wind farm occupies a large area and competes with other users of the maritime space. The integration of an offshore wind farm with other marine energy producers such as wave energy and other maritime users such as aquaculture farms may result in significant benefits in terms of economics, optimising spatial utilization, and mini...

  4. Power system integration and control of variable speed wind turbines

    Energy Technology Data Exchange (ETDEWEB)

    Eek, Jarle

    2009-12-15

    A wind power plant is a highly dynamic system that dependent on the type of technology requires a number of automatic control loops. This research deals with modelling, control and analysis related to power system integration of variable speed, pitch controlled wind turbines. All turbine components have been modelled and implemented in the power system simulation program SIMPOW, and a description of the modelling approach for each component is given. The level of model detail relates to the classical modelling of power system components for power system stability studies, where low frequency oscillations are of special importance. The wind turbine model includes a simplified representation of the developed rotor torque and the thrust force based on C{sub p-} and C{sub t} characteristic curves. The mechanical system model represents the fundamental torsional mode and the first mode of blades and tower movements. Two generator technologies have been investigated. The doubly fed induction generator (DFIG) and the stator converter interfaced permanent magnet synchronous generator (PMSG). A simplified model of a 2 level voltage source converter is used for both machine types. The generator converter controllers have been given special attention. All model components are linearized for the purpose of control system design and power system interaction related to small signal stability analysis. Different control strategies discussed in the literature have been investigated with regard to power system interaction aspects. All control parameters are identified using the internal model control approach. The analysis is focused on three main areas: 1. Identification of low damped oscillatory modes. This is carried out by the establishment and discussion of wind turbine modelling. 2. Interaction between control loops. A systematic approach is presented in order to analyse the influence of control loops used in variable speed wind turbines. 3.Impact on power system performance

  5. Dynamic Reactive Power Compensation of Large Scale Wind Integrated Power System

    DEFF Research Database (Denmark)

    Rather, Zakir Hussain; Chen, Zhe; Thøgersen, Paul;

    2015-01-01

    Due to progressive displacement of conventional power plants by wind turbines, dynamic security of large scale wind integrated power systems gets significantly compromised. In this paper we first highlight the importance of dynamic reactive power support/voltage security in large scale wind...... integrated power systems with least presence of conventional power plants. Then we propose a mixed integer dynamic optimization based method for optimal dynamic reactive power allocation in large scale wind integrated power systems. One of the important aspects of the proposed methodology is that unlike...... static optimal power flow based approaches, the proposed method considers detailed system dynamics and wind turbine grid code fulfilment while optimizing the allocation of dynamic reactive power sources. We also argue that in large scale wind integrated power systems, i) better utilization of existing...

  6. Security and Stability Analysis for Yunnan Power Grid with Wind Power Integration

    Directory of Open Access Journals (Sweden)

    Yinghui Qiu

    2013-12-01

    Full Text Available Wind power is sustainable, renewable and clean energy. There are abundant wind resources in Yunnan province, China. In recent years, wind power integration has developed rapidly in Yunnan province. With the first batch of the wind farm being built and a part of them going into production in Yunnan, the wind power resources will be large-scale developed and utilized in the future. Based on the wind power planning of Yunnan, the impacts of security and stability after wind power are studied in this paper. The major researches are made on the capacity analysis for accessing high-capacity wind farm, the analysis for power system voltage stability and comparison of different wind-generator model structures, thus finding out the most suitable choice for fan selection in Yunnan Power Grid.

  7. Modelling Aerosol Dispersion in Urban Street Canyons

    Science.gov (United States)

    Tay, B. K.; Jones, D. P.; Gallagher, M. W.; McFiggans, G. B.; Watkins, A. P.

    2009-04-01

    Flow patterns within an urban street canyon are influenced by various micrometeorological factors. It also represents an environment where pollutants such as aerosols accumulate to high levels due to high volumes of traffic. As adverse health effects are being attributed to exposure to aerosols, an investigation of the dispersion of aerosols within such environments is of growing importance. In particular, one is concerned with the vertical structure of the aerosol concentration, the ventilation characteristics of the street canyon and the influence of aerosol microphysical processes. Due to the inherent heterogeneity of the aerosol concentrations within the street canyon and the lack of spatial resolution of measurement campaigns, these issues are an on-going debate. Therefore, a modelling tool is required to represent aerosol dispersion patterns to provide insights to results of past measurement campaigns. Computational Fluid Dynamics (CFD) models are able to predict detailed airflow patterns within urban geometries. This capability may be further extended to include aerosol dispersion, by an Euler-Euler multiphase approach. To facilitate the investigation, a two-dimensional, multiphase CFD tool coupled with the k-epsilon turbulence model and with the capability of modelling mixed convection flow regimes arising from both wind driven flows and buoyancy effects from heated walls was developed. Assuming wind blowing perpendicularly to the canyon axis and treating aerosols as a passive scalar, an attempt will be made to assess the sensitivities of aerosol vertical structure and ventilation characteristics to the various flow conditions. Numerical studies were performed using an idealized 10m by 10m canyon to represent a regular canyon and 10m by 5m to represent a deep one. An aerosol emission source was assigned on the centerline of the canyon to represent exhaust emissions. The vertical structure of the aerosols would inform future directives regarding the

  8. Integration of Wind Energy Systems into Power Engineering Education Program at UW-Madison

    Energy Technology Data Exchange (ETDEWEB)

    Venkataramanan, Giri [Univ. of Wisconsin, Madison, WI (United States); Lesieutre, Bernard [Univ. of Wisconsin, Madison, WI (United States); Jahns, Thomas [Univ. of Wisconsin, Madison, WI (United States); Desai, Ankur R [Univ. of Wisconsin, Madison, WI (United States)

    2012-09-01

    This project has developed an integrated curriculum focused on the power engineering aspects of wind energy systems that builds upon a well-established graduate educational program at UW- Madison. Five new courses have been developed and delivered to students. Some of the courses have been offered on multiple occasions. The courses include: Control of electric drives for Wind Power applications, Utility Applications of Power Electronics (Wind Power), Practicum in Small Wind Turbines, Utility Integration of Wind Power, and Wind and Weather for Scientists and Engineers. Utility Applications of Power Electronics (Wind Power) has been provided for distance education as well as on-campus education. Several industrial internships for students have been organized. Numerous campus seminars that provide discussion on emerging issues related to wind power development have been delivered in conjunction with other campus events. Annual student conferences have been initiated, that extend beyond wind power to include sustainable energy topics to draw a large group of stakeholders. Energy policy electives for engineering students have been identified for students to participate through a certificate program. Wind turbines build by students have been installed at a UW-Madison facility, as a test-bed. A Master of Engineering program in Sustainable Systems Engineering has been initiated that incorporates specializations that include in wind energy curricula. The project has enabled UW-Madison to establish leadership at graduate level higher education in the field of wind power integration with the electric grid.

  9. Turbulent ventilation of a street canyon

    DEFF Research Database (Denmark)

    Nielsen, Morten

    2000-01-01

    A selection of turbulence data corresponding to 185 days of field measurements has een analysed. The non-ideal building geometry influenced the circulation patterns in the street canyon and the largest average vertical velocities were observed in the wake of an unbroken line of buildings. The...... small, and this suggests that most of the velocity fluctuations were fairly local and not caused by unsteady street vortices. The observed velocities scaled with the ambient wind speed except under low-wind conditions....

  10. Quantifying the total net benefits of grid integrated wind

    OpenAIRE

    DENNY, ELEANOR

    2007-01-01

    Throughout the world significant development is being encouraged in wind energy for electricity generation. A complete cost benefit analysis has been conducted in this paper on the impacts of grid connected wind generation. A dispatch model is used to determine the dispatches upon which the costs and benefits can be ascertained for different wind capacities, plant mixes and loads. These costs and benefits are then used to generate net benefit curves for wind generation and the level whe...

  11. Integrating Wind Power in Electricity Grids : an Economic Analysis

    OpenAIRE

    Liu, J; Kooten, van, K.; Pitt, L

    2005-01-01

    As a renewable energy source, wind power is gaining popularity as a favoured alternative to fossil fuel, nuclear and hydro power generation. In Europe, countries are required to achieve 15% of their energy consumption from wind by 2010 as the EU strives to meet its Kyoto obligations. Wind power is considered to be environmentally friendly and low cost. While environmental friendliness has come under scrutiny because wind turbines continue to pose a hazard to birds, are visually unappealing, a...

  12. Optimal Wind Energy Integration in Large-Scale Electric Grids

    Science.gov (United States)

    Albaijat, Mohammad H.

    The major concern in electric grid operation is operating under the most economical and reliable fashion to ensure affordability and continuity of electricity supply. This dissertation investigates the effects of such challenges, which affect electric grid reliability and economic operations. These challenges are: 1. Congestion of transmission lines, 2. Transmission lines expansion, 3. Large-scale wind energy integration, and 4. Phaser Measurement Units (PMUs) optimal placement for highest electric grid observability. Performing congestion analysis aids in evaluating the required increase of transmission line capacity in electric grids. However, it is necessary to evaluate expansion of transmission line capacity on methods to ensure optimal electric grid operation. Therefore, the expansion of transmission line capacity must enable grid operators to provide low-cost electricity while maintaining reliable operation of the electric grid. Because congestion affects the reliability of delivering power and increases its cost, the congestion analysis in electric grid networks is an important subject. Consequently, next-generation electric grids require novel methodologies for studying and managing congestion in electric grids. We suggest a novel method of long-term congestion management in large-scale electric grids. Owing to the complication and size of transmission line systems and the competitive nature of current grid operation, it is important for electric grid operators to determine how many transmission lines capacity to add. Traditional questions requiring answers are "Where" to add, "How much of transmission line capacity" to add, and "Which voltage level". Because of electric grid deregulation, transmission lines expansion is more complicated as it is now open to investors, whose main interest is to generate revenue, to build new transmission lines. Adding a new transmission capacity will help the system to relieve the transmission system congestion, create

  13. Offshore Wind Farm Clusters - Towards new integrated Design Tool

    DEFF Research Database (Denmark)

    Hasager, Charlotte Bay; Réthoré, Pierre-Elouan; Peña, Alfredo;

    In EERA DTOC testing of existing wind farm wake models against four validation data test sets from large offshore wind farms is carried out. This includes Horns Rev-1 in the North Sea, Lillgrund in the Baltic Sea, Roedsand-2 in the Baltic Sea and from 10 large offshore wind farms in Northern Euro...

  14. Integrating Wind Power in Electricity Grids : an Economic Analysis

    NARCIS (Netherlands)

    Liu, J.; Kooten, van G.C.; Pitt, L.

    2005-01-01

    As a renewable energy source, wind power is gaining popularity as a favoured alternative to fossil fuel, nuclear and hydro power generation. In Europe, countries are required to achieve 15% of their energy consumption from wind by 2010 as the EU strives to meet its Kyoto obligations. Wind power is c

  15. A spinner-integrated wind lidar for enhanced wind turbine control

    OpenAIRE

    Mikkelsen, Torben; Angelou, Nikolas; Hansen, Kasper Hjorth; Sjöholm, Mikael; Harris, M; C. Slinger; Hadley, P.; Scullion, R.; Ellis, G.; Vives, G.

    2013-01-01

    A field test with a continuous wave wind lidar (ZephIR) installed in the rotating spinner of a wind turbine for unimpeded preview measurements of the upwind approaching wind conditions is described. The experimental setup with the wind lidar on the tip of the rotating spinner of a large 80 m rotor diameter, 59 m hub height 2.3 MW wind turbine (Vestas NM80), located at Tjæreborg Enge in western Denmark is presented. Preview wind data at two selected upwind measurement distances, acquired durin...

  16. Dynamic performance of a novel offshore power system integrated with a wind farm

    DEFF Research Database (Denmark)

    Orlandini, Valentina; Pierobon, Leonardo; Schløer, Signe;

    2016-01-01

    Offshore wind technology is rapidly developing and a wind farm can be integrated with offshore power stations. This paper considers as case study a futuristic platform powered by a wind farm and three combined cycle units consisting of a gas turbine and an ORC (organic Rankine cycle) module...... of the system is compared with a simplified plant consisting of three gas turbines and a wind farm, in order to identify benefits of the installation of the ORC system. The maximum allowable wind power is 10 MW for a nominal platform load of 30 MW. The results show that the presence of the ORC system allows...

  17. On the integration of wind generators on weak grids and island grids

    International Nuclear Information System (INIS)

    Wind energy is now an energy that can not be ignored. Because of intrinsic characteristics (scattered primary energy, generators with different technologies, use of power electronics interface), wind energy system integration in distribution grids leads to real problems in terms of impacts. With recent standard changes, it is necessary to study the possibilities of each technology of wind turbines to answer or not to these new constraints. This PhD thesis focuses on a comparison of the main present wind turbines concerning three points of discussion: energy quality, fault ride through, ancillary services (voltage and frequency). It insists on the possibilities in terms of control laws for variable speed wind turbines. (author)

  18. Dynamic model of frequency control in Danish power system with large scale integration of wind power

    DEFF Research Database (Denmark)

    Basit, Abdul; Hansen, Anca Daniela; Sørensen, Poul Ejnar

    2013-01-01

    This work evaluates the impact of large scale integration of wind power in future power systems when 50% of load demand can be met from wind power. The focus is on active power balance control, where the main source of power imbalance is an inaccurate wind speed forecast. In this study, a Danish...... power system model with large scale of wind power is developed and a case study for an inaccurate wind power forecast is investigated. The goal of this work is to develop an adequate power system model that depicts relevant dynamic features of the power plants and compensates for load generation...

  19. Integration of 18 GW Wind Energy into the Energy Market. Practical Experiences in Germany. Experiences with large-scale integration of wind power into power systems

    International Nuclear Information System (INIS)

    This work describes the integration of 18 GW of wind power into the German energy market. The focus lies on reporting practical experiences concerning the use of wind energy in Germany within the framework of the renewable energy act (EEG) and the immediate exchange of wind power between the four German grid control areas. Due to the EEG the demand for monitoring the current energy production of wind farms and for short-term predictions of wind power has significantly increased and opened a broader market for these services. In particular for trading on the intraday market ultra short term predictions in the time frame of 1 to 10 hours require different approaches than usual dayahead predictions because the large numerical meteorological models are not sufficiently optimized for very short time horizons. It is shown that for this range a combination of a statistical and a deterministic model leads to significant improvements and stable results as it unites the characteristics of the current wind power production with the synoptic-scale meteorological situation. The possible concepts of balancing the remaining differences between predicted and actual wind power generation are discussed. As wind power prediction errors and load forecasting errors are uncorrelated, benefits can arise from a combined balancing. Finally practical experiences with wind power fluctuations and large forecast errors are presented.

  20. Wind power integration studies using a multi-stage stochastic electricity system model

    DEFF Research Database (Denmark)

    Meibom, Peter; Barth, R.; Brand, H.;

    2007-01-01

    A large share of integrated wind power causes technical and financial impacts on the operation of the existing electricity system due to the fluctuating behaviour and unpredictability of wind power. The presented stochastic electricity market model optimises the unit commitment considering four...... kinds of electricity markets (e.g. a spot and balancing market) and taking into account the stochastic behaviour of the wind power generation and of the prediction error. It can be used for the evaluation of varying electricity prices and system costs due to wind power integration...

  1. A spinner-integrated wind lidar for enhanced wind turbine control

    DEFF Research Database (Denmark)

    Mikkelsen, Torben; Angelou, Nikolas; Hansen, Kasper Hjorth;

    2013-01-01

    A field test with a continuous wave wind lidar (ZephIR) installed in the rotating spinner of a wind turbine for unimpeded preview measurements of the upwind approaching wind conditions is described. The experimental setup with the wind lidar on the tip of the rotating spinner of a large 80 m roto...... of the spinner lidar data, is investigated. Finally, the potential for enhancing turbine control and performance based on wind lidar preview measurements in combination with feed-forward enabled turbine controllers is discussed. Copyright © 2012 John Wiley & Sons, Ltd....

  2. Final Report on the Creation of the Wind Integration National Dataset (WIND) Toolkit and API: October 1, 2013 - September 30, 2015

    Energy Technology Data Exchange (ETDEWEB)

    Hodge, Bri-Mathias [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-04-08

    The primary objective of this work was to create a state-of-the-art national wind resource data set and to provide detailed wind plant output data for specific sites based on that data set. Corresponding retrospective wind forecasts were also included at all selected locations. The combined information from these activities was used to create the Wind Integration National Dataset (WIND), and an extraction tool was developed to allow web-based data access.

  3. Large eddy simulation of flow in a street canyon with tree planting under various atmospheric instability conditions

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In this work, a large eddy simulation (LES) model, which includes momentum and heat source (or sink) inside the tree planting layer, is proposed for the simulation of flow in a street canyon with tree planting. Vegetation canopy layer simulation shows that this model can be used to simulate the velocity distribution and temperature variation inside the canopy layer. Effects of atmospheric instability on flow and pollutant distribution in a street canyon with tree planting of an aspect ratio of 0.5 are studied. Results show that compared with the canyon with no tree planting (or the exposed street canyon), the canyon with tree planting shows a reduced wind circulation and pollutant exchange rate (PER) at the top layer of the street canyon, which induces the increase in the pollutant concentrations near road surface, leeward wall and windward wall. When street canyon atmosphere is under a strongly unstable condition, wind velocity decreases while pollutant concentration is increased in the areas near the street canyon top, road surface, leeward and windward walls, compared with the wind velocity in the street canyon with the neutral stratification. When street canyon atmosphere is under a weakly unstable condition, wind velocity weakens near the street canyon top and windward wall, but strengthens near the road surface and leeward wall, and pollutant concentration is decreased near the leeward and windward walls and is increased between the two rows of trees. When the street canyon atmosphere is under an unstable condition, PER is lower than that under the neutral stratification.

  4. Advanced control strategies to integrate German offshore wind potential into electrical energy sypply

    Energy Technology Data Exchange (ETDEWEB)

    Rohrig, K.; Schloegl, F.; Jursa, R.; Wolff, M. [Institut fuer Solare Energieversorgungstechnik (ISET), Kassel (Germany); Fischer, F.; Hartge, S. [ENERCON GmbH, Aurich (Germany); Valov, B.; Heier, S. [Kassel Univ. (Gesamthochschule) (Germany)

    2005-07-01

    The paper describes the technical status and presents new concepts, models and approaches for the technical assistance of large scale wind power integration into the electrical energy supply system in Germany. It shows the technical and economic problems with the integration of high penetration of wind power plant in the network and the total electrical system. After an analysis of the effects of increased wind power generation on system planning and grid operation, we discuss innovative operational control concepts for large (offshore) wind farms. These concepts will provide a multitude of new possibilities to enable simple, flexible and undisturbed reaction to the demands of participants (wind farm operators, grid operators). These operational control strategies are mainly based on ISETs successful employed wind power prediction tools, operated by all German TSO's, and will enable energy and power control, as well as the provision of reactive power, in order to achieve comparable properties to conventional power plant types. (orig.)

  5. Systematic framework for the efficient integration of wind technologies into buildings

    Directory of Open Access Journals (Sweden)

    Ashraf A. ELMokadem

    2016-03-01

    Full Text Available The renewed interest that is being paid by architects, project developers and local governments to integrate wind turbines with buildings is mainly required a framework to unify much data, criteria and variables to ease the design process to many architects. Therefore, this paper introduces and elaborates the systematic framework towards the efficient integration of wind technologies into new building. Moreover, it evaluates the framework effectiveness by comparing the current status of wind technologies integration into a building with the suggested status if the framework is followed.

  6. Research Developments on Power System Integration of Wind Power

    DEFF Research Database (Denmark)

    Chen, Zhe; Hansen, Jens Carsten; Wu, Qiuwei;

    2011-01-01

    variability and prediction, wind power plant ancillary services, grid connection and operation, Smart grids and demand side management under market functionality. The topics of the first group of PhD program starting 2011 under the wind energy Sino-Danish Centre for Education & Research (SDC) are also...

  7. Grid Integration Issues for Large Scale Wind Power Plants (WPPs)

    DEFF Research Database (Denmark)

    Wu, Qiuwei; Xu, Zhao; Østergaard, Jacob

    2010-01-01

    The penetration level of wind power into the power system over the world have been increasing very fast in the last few years and is still keeping the fast growth rate. It is just a matter of time that the wind power will be comparable to the conventional power generation. Therefore, many transmi...

  8. Empirical Analysis of the Variability of Wind Generation in India: Implications for Grid Integration

    Energy Technology Data Exchange (ETDEWEB)

    Phadke, Amol; Abhyankar, NIkit; Rao, Poorvi

    2014-06-17

    We analyze variability in load and wind generation in India to assess its implications for grid integration of large scale wind projects using actual wind generation and load data from two states in India, Karnataka and Tamil Nadu. We compare the largest variations in load and net load (load ?wind, i.e., load after integrating wind) that the generation fleet has to meet. In Tamil Nadu, where wind capacity is about 53percent of the peak demand, we find that the additional variation added due to wind over the current variation in load is modest; if wind penetration reaches 15percent and 30percent by energy, the additional hourly variation is less than 0.5percent and 4.5percent of the peak demand respectively for 99percent of the time. For wind penetration of 15percent by energy, Tamil Nadu system is found to be capable of meeting the additional ramping requirement for 98.8percent of the time. Potential higher uncertainty in net load compared to load is found to have limited impact on ramping capability requirements of the system if coal plants can me ramped down to 50percent of their capacity. Load and wind aggregation in Tamil Nadu and Karnataka is found to lower the variation by at least 20percent indicating the benefits geographic diversification. These findings suggest modest additional flexible capacity requirements and costs for absorbing variation in wind power and indicate that the potential capacity support (if wind does not generate enough during peak periods) may be the issue that has more bearing on the economics of integrating wind

  9. Modelling the potential for wind energy integration on China’s coal-heavy electricity grid

    Science.gov (United States)

    Davidson, Michael R.; Zhang, Da; Xiong, Weiming; Zhang, Xiliang; Karplus, Valerie J.

    2016-07-01

    Expanding the use of wind energy for electricity generation forms an integral part of China’s efforts to address degraded air quality and climate change. However, the integration of wind energy into China’s coal-heavy electricity system presents significant challenges owing to wind’s variability and the grid’s system-wide inflexibilities. Here we develop a model to predict how much wind energy can be generated and integrated into China’s electricity mix, and estimate a potential production of 2.6 petawatt-hours (PWh) per year in 2030. Although this represents 26% of total projected electricity demand, it is only 10% of the total estimated physical potential of wind resources in the country. Increasing the operational flexibility of China’s coal fleet would allow wind to deliver nearly three-quarters of China’s target of producing 20% of primary energy from non-fossil sources by 2030.

  10. 9{sup th} international workshop on large-scale integration of wind power into power systems as well as on transmission networks for offshore wind power plants. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Betancourt, Uta; Ackermann, Thomas (eds.)

    2010-07-01

    Within the 9th International Workshop on large-scale integration of wind power into power systems as well as on transmission networks for offshore wind power plants at 18th to 19th October, 2010 in Quebec (Canada), lectures and poster papers were presented to the following themes: (1) Keynote session and panel; (2) European grid integration studies; (3) Modeling; (4) Wind forecasting; (5) North American grid integration studies; (6) Voltage stability and control; (7) Grid codes and impact studies; (8) Canadian University research (WESNet); (9) Operation and dispatch; (9) Offshore wind power plants; (10) Frequency Control; (11) Methodologies to estimate wind power impacts on power systems, summaries from IEAWIND collaboration; (12) HVDC; (13) Grid codes and system impact studies; (14) Modeling and validation; (15) Regulations, markets and offshore wind energy; (16) Integration issues; (17) Wind turbine control system; (18) Energy management and IT solutions.

  11. Beyond Classical Upscaling: Integrated Aeroservoelastic Design and Optimization of Large Offshore Wind Turbines

    NARCIS (Netherlands)

    Ashuri, T.

    2012-01-01

    Issues related to environmental concern and fossil fuel exhaustion has made wind energy the most widely accepted renewable energy resource. However, there are still several challenges to be solved such as the integrated design of wind turbines, aeroelastic response and stability prediction, grid int

  12. Market integration of wind power in electricity system balancing

    DEFF Research Database (Denmark)

    Sorknæs, Peter; Andersen, Anders N.; Tang, Jens;

    2013-01-01

    In most countries markets for electricity are divided into wholesale markets on which electricity is traded before the operation hour, and real-time balancing markets to handle the deviations from the wholesale trading. So far, wind power has been sold only on the wholesale market and has been...... known to increase the need for balancing. This article analyses whether wind turbines in the future should participate in the balancing markets and thereby play a proactive role. The analysis is based on a real-life test of proactive participation of a wind farm in West Denmark. It is found...

  13. 2007 Weather and Aeolian Sand-Transport Data from the Colorado River Corridor, Grand Canyon, Arizona

    Science.gov (United States)

    Draut, Amy E.; Andrews, Timothy; Fairley, Helen C.; Brown, Christopher R.

    2009-01-01

    Weather data constitute an integral part of ecosystem monitoring in the Colorado River corridor and are particularly valuable for understanding processes of landscape change that contribute to the stability of archeological sites. Data collected in 2007 are reported from nine weather stations in the Colorado River corridor through Grand Canyon, Ariz. The stations were deployed in February and March 2007 to measure wind speed and direction, rainfall, air temperature, relative humidity, and barometric pressure. Sand traps near each weather station collect windblown sand, from which daily aeolian sand-transport rates are calculated. The data reported here were collected as part of an ongoing study to test and evaluate methods for quantifying processes that affect the physical integrity of archeological sites along the river corridor; as such, these data can be used to identify rainfall events capable of causing gully incision and to predict likely transport pathways for aeolian sand, two landscape processes integral to the preservation of archeological sites. Weather data also have widespread applications to other studies of physical, cultural, and biological resources in Grand Canyon. Aeolian sand-transport data reported here, collected in the year before the March 2008 High-Flow Experiment (HFE) at Glen Canyon Dam, represent baseline data against which the effects of the 2008 HFE on windblown sand will be compared in future reports.

  14. Modeling the Effect of Wider Canyons on Urban Heating

    Directory of Open Access Journals (Sweden)

    Rizwan Ahmed Memon

    2011-04-01

    Full Text Available The k-? turbulence model is adopted in this study to simulate the impact of street canyon AR (Aspect Ratios on heating within street canyon. The two-dimensional model was validated for RANS (Reynolds Averaged Navier Stokes and energy transport equations. The validation process confirms that the results of the model for airtemperature and wind speed could be trusted. The application of the said model is carried out to ideal street canyons of ARs (ratio of building-height-to-street-width from 0.4 to 2 with the same boundary conditions. Notably, street canyon aspect ratio was calculated by varying the street width while keeping the building height constant. Results show that the weighted-average-air-temperature within AR 0.4 was around 0.8% (i.e. 2.4K higher than that within AR 2.0. Conversely, there was strong correlation (i.e., R2>0.9 between air temperature within the street canyon and street canyon AR. Results demonstrate stronger influence of vertical velocity on heating within street canyon. Evidently, increased vertical velocity decreased the temperatures. Conversely, temperatures were higher along the leeward side of the canyon in lower ARs.

  15. Power quality and integration of wind farms in weak grids in India

    DEFF Research Database (Denmark)

    Sørensen, Poul Ejnar; Madsen, Peter Hauge; Vikkelsø, A.;

    2000-01-01

    This is the final report of a joint Danish and Indian project "Power Quality and Integration of Wind Farms in Weak Grids". The power quality issues have been studied and analysed with the Indian conditions as a case. On the basis of meetings with Danishwind turbine industry, Indian electricity...... boards, nodal agencies, wind turbine industry and authorities, the critical power quality as-pects in India have been identified. Measurements on selected wind farms and wind turbines have quantified the powerquality, and analyses of power quality issues, especially reactive power compensation, have been...

  16. 50 pct. wind power in Denmark and power market integration

    International Nuclear Information System (INIS)

    This paper presents the results of an extensive analysis of how to incorporate 50 pct. wind power in the Danish electricity system and what the welfare economic costs and benefits will be for Denmark as well as for the North European Region. To estimate the consequences for the development of the power system and the costs and benefits of the increased wind power, model analysis has been carried out using the electricity market model, Balmorel. For this analysis the model covers the Nordic countries and Germany. Two scenarios have been analysed. In the first scenario, the reference scenario, all investments in production capacity including wind power is base on market mechanisms. In the second scenario, the 50 pct. wind scenario, the investments in wind power in Denmark are governed by a target of establishing 50 pct. wind power in Denmark in 2025. In the second scenario 3500 MW wind power is established on land and by 2025 Denmark will have 2900 MW wind power offshore. The calculations result in a welfare economic benefit for Denmark of approximately 20 million DKK pr. year on average. For the Nordic countries and Germany as a whole the benefit is 660 million DKK pr. year on average. This benefit is dependent on a welfare economic discount rate of 3%. The welfare gain takes into account costs of additional infrastructure, trade effects, savings on fuel consumption, investment and operating costs on plants as well as reduced consumption of CO2 quotas, and the damaging effects of NOx and SO2 emissions. (au)

  17. Investigation of Geomorphic and Seismic Effects on the 1959 Madison Canyon, Montana, Landslide Using an Integrated Field, Engineering Geomorphology Mapping, and Numerical Modelling Approach

    Science.gov (United States)

    Wolter, A.; Gischig, V.; Stead, D.; Clague, J. J.

    2016-06-01

    We present an integrated approach to investigate the seismically triggered Madison Canyon landslide (volume = 20 Mm3), which killed 26 people in Montana, USA, in 1959. We created engineering geomorphological maps and conducted field surveys, long-range terrestrial digital photogrammetry, and preliminary 2D numerical modelling with the objective of determining the conditioning factors, mechanisms, movement behaviour, and evolution of the failure. We emphasise the importance of both endogenic (i.e. seismic) and exogenic (i.e. geomorphic) processes in conditioning the slope for failure and hypothesise a sequence of events based on the morphology of the deposit and seismic modelling. A section of the slope was slowly deforming before a magnitude-7.5 earthquake with an epicentre 30 km away triggered the catastrophic failure in August 1959. The failed rock mass rapidly fragmented as it descended the slope towards Madison River. Part of the mass remained relatively intact as it moved on a layer of pulverised debris. The main slide was followed by several debris slides, slumps, and rockfalls. The slide debris was extensively modified soon after the disaster by the US Army Corps of Engineers to provide a stable outflow channel from newly formed Earthquake Lake. Our modelling and observations show that the landslide occurred as a result of long-term damage of the slope induced by fluvial undercutting, erosion, weathering, and past seismicity, and due to the short-term triggering effect of the 1959 earthquake. Static models suggest the slope was stable prior to the 1959 earthquake; failure would have required a significant reduction in material strength. Preliminary dynamic models indicate that repeated seismic loading was a critical process for catastrophic failure. Although the ridge geometry and existing tension cracks in the initiation zone amplified ground motions, the most important factors in initiating failure were pre-existing discontinuities and seismically induced

  18. Great Lakes O shore Wind Project: Utility and Regional Integration Study

    Energy Technology Data Exchange (ETDEWEB)

    Sajadi, Amirhossein [Case Western Reserve Univ., Cleveland, OH (United States); Loparo, Kenneth A. [Case Western Reserve Univ., Cleveland, OH (United States); D' Aquila, Robert [General Electric (GE), Albany, NY (United States); Clark, Kara [National Renewable Energy Lab. (NREL), Golden, CO (United States); Waligorski, Joseph G. [FirstEnergy, Akron, OH (United States); Baker, Scott [PJM Interconnection, Audubon, PA (United States)

    2016-06-30

    This project aims to identify transmission system upgrades needed to facilitate offshore wind projects as well as operational impacts of offshore generation on operation of the regional transmission system in the Great Lakes region. A simulation model of the US Eastern Interconnection was used as the test system as a case study for investigating the impact of the integration of a 1000MW offshore wind farm operating in Lake Erie into FirstEnergy/PJM service territory. The findings of this research provide recommendations on offshore wind integration scenarios, the locations of points of interconnection, wind profile modeling and simulation, and computational methods to quantify performance, along with operating changes and equipment upgrades needed to mitigate system performance issues introduced by an offshore wind project.

  19. The Western Wind and Solar Integration Study Phase 2 (Executive Summary)

    Energy Technology Data Exchange (ETDEWEB)

    Lew, Debra [National Renewable Energy Lab. (NREL), Golden, CO (United States); Brinkman, Greg [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2013-09-01

    The electric grid is a highly complex, interconnected machine, and changing one part of the grid can have consequences elsewhere. Adding wind and solar affects the operation of the other power plants and adding high penetrations can induce cycling of fossil-fueled generators. Cycling leads to wear-and-tear costs and changes in emissions. Phase 2 of the Western Wind and Solar Integration Study (WWSIS-2) evaluated these costs and emissions and simulated grid operations for a year to investigate the detailed impact of wind and solar on the fossil-fueled fleet. This built on Phase 1, one of the largest wind and solar integration studies ever conducted, which examined operational impacts of high wind and solar penetrations in the West(GE Energy 2010).

  20. Integration of a wind farm with a wave- and an aquaculture farm

    DEFF Research Database (Denmark)

    He, W.; Weissenberger, J.; Bergh, Ø.;

    with other marine energy producers such as wave energy and other maritime users such as aquaculture farms may result in significant benefits in terms of economics, optimising spatial utilization, and minimising the environmental impact. In this research project, the integration benefits and disadvantages......There is a growing interest in placing wind farms offshore. 140 GW of offshore wind are currently being planned to reach the EU energy 2020 goal. However, an offshore wind farm occupies a large area and competes with other users of the maritime space. The integration of an offshore wind farm...... have been evaluated by the proposed study cases, however these cases are unrelated to Statoil’s planned wind projects....

  1. Evaluation of an Integrated Roof Wind Energy System for urban environments

    Science.gov (United States)

    Patankar, B.; Tyagi, R.; Kiss, D.; Suma, A. B.

    2016-09-01

    Integrating renewable energy in the urban environment is of importance for the renewable energy goals set by the European Union. This research is to study and evaluate wind energy potential for an Integrated Roof Wind Energy System on the rooftop of the buildings of different heights and in different locations with the help of numerical modelling (CFD). The Navier-Stokes equations are solved using the SIMPLE algorithm while the turbulence is modelled using the k-ω SST equations. All the simulations are performed using OpenFOAM. Results shows that wind speed can be accelerated by ∼1.4 times till it reaches the periphery of the turbine inside the unit, which will increase wind power output considerably. This results in power factor increase of 1.7 for tall buildings. Therefore, enabling combined micro wind and solar energy systems to be a viable option for urban environments.

  2. Role of Concentrating Solar Power in Integrating Solar and Wind Energy: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Denholm, P.; Mehos, M.

    2015-06-03

    As wind and solar photovoltaics (PV) increase in penetration it is increasingly important to examine enabling technologies that can help integrate these resources at large scale. Concentrating solar power (CSP) when deployed with thermal energy storage (TES) can provide multiple services that can help integrate variable generation (VG) resources such as wind and PV. CSP with TES can provide firm, highly flexible capacity, reducing minimum generation constraints which limit penetration and results in curtailment. By acting as an enabling technology, CSP can complement PV and wind, substantially increasing their penetration in locations with adequate solar resource.

  3. 75 FR 47301 - Cedro Hill Wind LLC; Butler Ridge Wind Energy Center, LLC; High Majestic Wind Energy Center, LLC...

    Science.gov (United States)

    2010-08-05

    ...; EG10-36-000; EG10-37-000; EG10-38-000] Cedro Hill Wind LLC; Butler Ridge Wind Energy Center, LLC; High Majestic Wind Energy Center, LLC; Wessington Wind Energy Center, LLC; Juniper Canyon Wind Power LLC; Loraine Windpark Project, LLC; White Oak Energy LLC; Meadow Lake Wind Farm III LLC; Meadow Lake Wind...

  4. Analysis of Highly Wind Power Integrated Power System model performance during Critical Weather conditions

    DEFF Research Database (Denmark)

    Basit, Abdul; Hansen, Anca Daniela; Sørensen, Poul Ejnar;

    2014-01-01

    . For this purpose, the power system model has been developed that represents the relevant dynamic features of power plants and compensates for power imbalances caused by the forecasting error during critical weather conditions. The regulating power plan, as an input time series for the developed power system model......Secure power system operation of a highly wind power integrated power system is always at risk during critical weather conditions, e.g. in extreme high winds. The risk is even higher when 50% of the total electricity consumption has to be supplied by wind power, as the case for the future Danish......, is provided by the hour-ahead power balancing model, i.e. Simulation power Balancing model (SimBa. The regulating power plan is prepared from day-ahead power production plan and hour-ahead wind power forecast. The wind power (forecasts and available) are provided by the Correlated Wind power fluctuations (Cor...

  5. An Integrated Structural Strength Analysis Method for Spar Type Floating Wind Turbine

    Institute of Scientific and Technical Information of China (English)

    胡志强; 刘毅; 王晋

    2016-01-01

    An integrated structural strength analysis method for a Spar type floating wind turbine is proposed in this paper, and technical issues related to turbine structure modeling and stress combination are also addressed. The NREL-5MW “Hywind” Spar type wind turbine is adopted as study object. Time-domain dynamic coupled simulations are performed by a fully-coupled aero-hydro-servo-elastic tool, FAST, on the purpose of obtaining the dynamic characteristics of the floating wind turbine, and determining parameters for design load cases of finite element calculation. Then design load cases are identified, and finite element analyses are performed for these design load cases. The structural stresses due to wave-induced loads and wind-induced loads are calculated, and then combined to assess the structural strength of the floating wind turbine. The feasibility of the proposed structural strength analysis method for floating wind turbines is then validated.

  6. Priority Control Strategy of VSC-MTDC System for Integrating Wind Power

    Directory of Open Access Journals (Sweden)

    Wen-ning Yan

    2015-01-01

    Full Text Available For the obvious advantages in integrating wind power, multiterminal HVDC transmission system (VSC-MTDC is widely used. The priority control strategy is proposed in this paper considering the penetration rate of wind power for the AC grid. The strategy aims to solve the problems of power allocation and DC voltage control of the DC system. The main advantage of this strategy is that the demands for wind power of different areas can be satisfied and a power reference for the wind power trade can also be provided when wind farms transmit active power to several AC grids through the DC network. The objective is that power is well distributed according to the output power of wind farm with the demand of AC system and satisfactory control performance of DC voltage is obtained.

  7. An integrated structural strength analysis method for Spar type floating wind turbine

    Science.gov (United States)

    Hu, Zhi-qiang; Liu, Yi; Wang, Jin

    2016-04-01

    An integrated structural strength analysis method for a Spar type floating wind turbine is proposed in this paper, and technical issues related to turbine structure modeling and stress combination are also addressed. The NREL-5MW "Hywind" Spar type wind turbine is adopted as study object. Time-domain dynamic coupled simulations are performed by a fully-coupled aero-hydro-servo-elastic tool, FAST, on the purpose of obtaining the dynamic characteristics of the floating wind turbine, and determining parameters for design load cases of finite element calculation. Then design load cases are identified, and finite element analyses are performed for these design load cases. The structural stresses due to wave-induced loads and wind-induced loads are calculated, and then combined to assess the structural strength of the floating wind turbine. The feasibility of the proposed structural strength analysis method for floating wind turbines is then validated.

  8. Use of CFD to optimize the performance of a building-integrated wind turbine

    Energy Technology Data Exchange (ETDEWEB)

    Abu-Hijleh, B.A.K. [British Univ. on Dubai (United Arab Emirates)

    2009-03-11

    Large-sized wind turbines are increasingly being integrated within the design of tall buildings in order to access the high speed and low turbulence wind prevalent at high elevations. Building-integrated wind turbines are exposed to the damaging effects of cross-winds and vibrations. In this study, a computational fluid dynamics (CFD) simulation was conducted to analyze the effectiveness of wind turbine guide vanes in increasing air mass flow rate, reducing cross-flow velocity, and reducing turbulence at the inlet plane of a building-integrated wind turbine installed in a 400 meters high building that is currently being designed in Dubai. Different guide vane configurations included simple stationary straight vanes and adjustable inlet-angle guide vanes. Interior wall configurations were also tested. Air flow simulations were conducted using a 2-D geometrical representation of a cross-sectional view of the building. The study showed that the best configuration was comprised of a scoop-shaped front end and a diffuser-shaped back end. Results of the study will be used to reduce sources of vibration and to maximize the power output of large building-integrated wind turbines. 6 refs., 2 tabs., 9 figs.

  9. Integration of Wind Turbines with Compressed Air Energy Storage

    Science.gov (United States)

    Arsie, I.; Marano, V.; Rizzo, G.; Moran, M.

    2009-08-01

    Some of the major limitations of renewable energy sources are represented by their low power density and intermittent nature, largely depending upon local site and unpredictable weather conditions. These problems concur to increase the unit costs of wind power, so limiting their diffusion. By coupling storage systems with a wind farm, some of the major limitations of wind power, such as a low power density and an unpredictable nature, can be overcome. After an overview on storage systems, the Compressed Air Energy Storage (CAES) is analyzed, and the state of art on such systems is discussed. A Matlab/Simulink model of a hybrid power plant consisting of a wind farm coupled with CAES is then presented. The model has been successfully validated starting from the operating data of the McIntosh CAES Plant in Alabama. Time-series neural network-based wind speed forecasting are employed to determine the optimal daily operation strategy for the storage system. A detailed economic analysis has been carried out: investment and maintenance costs are estimated based on literature data, while operational costs and revenues are calculated according to energy market prices. As shown in the paper, the knowledge of the expected available energy is a key factor to optimize the management strategies of the proposed hybrid power plant, allowing to obtain environmental and economic benefits.

  10. Assessing the level of integration in the offshore wind industry value chain

    DEFF Research Database (Denmark)

    Martinez-Neri, Ivan; Mikkelsen, Ole Stegmann; Stentoft, Jan

    2014-01-01

    The offshore wind industry (OWI) has experienced an explosive growth within the course of a decade and because of this rapid expansion, the industry has not had the opportunity to integrate well and be-come more efficient. The aim of this paper is to contribute to the understanding...... of the integration level of the offshore wind industry value chain. The work relies on a review of international peer-reviewed journals. The empirical basis of the paper is based on interviews with key players in the industry. The scope of this study covers the wind turbine generator, foundations, subsea cables......, offshore substation, installation vessels and the wind farm developer. The preliminary findings are that the different indus-trial sectors participating in the OWI are not aware of the maturity level of the sector. The fact that some developers are disintegrating the already integrated supply of some...

  11. An Integrated Risk Framework for Gigawatt-scale Deployments of Renewable Energy: The U.S. Wind Energy Case

    Energy Technology Data Exchange (ETDEWEB)

    Ram, B. [Energetics, Inc., Columbia, MD (United States)

    2010-04-01

    Assessing the potential environmental and human effects of deploying renewable wind energy requires a new way of evaluating potential environmental and human impacts. This paper explores an integrated risk framework for renewable wind energy siting decisionmaking.

  12. Composition Modeling and Equivalence of an Integrated Power Generation System of Wind, Photovoltaic and Energy Storage Unit

    Institute of Scientific and Technical Information of China (English)

    WANG Haohuai; TANG Yong; HOU Junxian; ZOU Jiangfeng; LIANGShuang; SU Feng

    2011-01-01

    The characteristic of wind and solar generation is random and fluctuant. In order to improve their generation performance, the integrated power generation of wind, photovoltaic (PV) and energy storage is a focus in the study. In this paper,

  13. Particle fluxes and their drivers in the Avilés submarine canyon and adjacent slope, central Cantabrian margin, Bay of Biscay

    Science.gov (United States)

    Rumín-Caparrós, A.; Sanchez-Vidal, A.; González-Pola, C.; Lastras, G.; Calafat, A.; Canals, M.

    2016-05-01

    The Avilés Canyon in the central Cantabrian margin is one of the largest submarine canyons in Europe, extending from the shelf edge at 130 m depth to 4765 m depth in the Biscay abyssal plain. In this paper we present the results of a year-round (March 2012 to April 2013) study of particle fluxes in this canyon and the adjacent continental slope. Three mooring lines equipped with automated sequential sediment traps, high-accuracy conductivity-temperature recorders and current meters allowed measuring total mass fluxes and their major components (lithogenics, calcium carbonate, opal and organic matter) in the settling material jointly with a set of environmental parameters. The integrated analysis of the data obtained from the moorings together with remote sensing images and meteorological and hydrographical data has shed light on the sources of particles and the across- and along margin mechanisms involved in their transfer to the deep. Our results allow interpreting the dynamics of the sedimentary particles in the study area. Two factors play a critical role: (i) direct delivery of river-sourced material to the narrow continental shelf, and (ii) major resuspension events caused by large waves and near bottom currents developing at the occasion of the rather frequent severe storms that are typical of the Cantabrian Sea. Wind direction and subsequent wind-driven currents largely determine the way sedimentary particles reach the canyon. While westerly winds favour the injection of sediments into the Avilés Canyon mainly by building an offshore transport in the bottom Ekman layer, easterly winds ease the offshore advection of particulate matter towards the Avilés Canyon and its adjacent western slope principally through the surface Ekman layer. Furthermore, repeated cycles of semidiurnal tides add an extra amount of energy to the prevailing bottom currents and actively contribute to keep a permanent background of suspended particles in near-bottom waters. High

  14. Technical issues for wind energy integration in power systems: projections in Italy

    Energy Technology Data Exchange (ETDEWEB)

    Pantaleo, A.; Pellerano, A.; Trovato, M.

    2003-12-01

    This paper is review of the main technical issues of wind energy integration in power systems. After summarizing the main factors affecting this integration and reviewing the analytical studies that have been carried out, the perspectives for growth in Italy are investigated. The wind power penetration projections for Italy show that the installed wind capacity should be in the range of 3,000 - 5,000 MW by 2010, with a wind power penetration level of 4.5 to 7% of peak demand. Even if, at a global level, no substantial problems in power system operation are expected, the high concentration of the Italian wind energy resource in a few areas in Southern Italy, Sicily and Sardinia Regions, can cause grid integration difficulties. In fact, new transmission networks should be built to connect this dispersed energy source to the power system. Moreover, the large wind penetration expected in isolated areas, such as in Sardinia Island, can cause load-following and regulation problems, especially during low-load periods and morning ramp-up or evening drop-off hours. These issues should be taken into account to avoid the risk of wind generation curtailments. (author)

  15. Interdisciplinary design study of a high-rise integrated roof wind energy system

    Science.gov (United States)

    Dekker, R. W. A.; Ferraro, R. M.; Suma, A. B.; Moonen, S. P. G.

    2012-10-01

    Today's market in micro-wind turbines is in constant development introducing more efficient solutions for the future. Besides the private use of tower supported turbines, opportunities to integrate wind turbines in the built environment arise. The Integrated Roof Wind Energy System (IRWES) presented in this work is a modular roof structure integrated on top of existing or new buildings. IRWES is build up by an axial array of skewed shaped funnels used for both wind inlet and outlet. This inventive use of shape and geometry leads to a converging air capturing inlet to create high wind mass flow and velocity toward a Vertical Axis Wind Turbine (VAWT) in the center-top of the roof unit for the generation of a relatively high amount of energy. The scope of this research aims to make an optimized structural design of IRWES to be placed on top of the Vertigo building in Eindhoven; analysis of the structural performance; and impact to the existing structure by means of Finite Element Modeling (FEM). Results show that the obvious impact of wind pressure to the structural design is easily supported in different configurations of fairly simple lightweight structures. In particular, the weight addition to existing buildings remains minimal.

  16. Interdisciplinary design study of a high-rise integrated roof wind energy system

    Directory of Open Access Journals (Sweden)

    Moonen S.P.G.

    2012-10-01

    Full Text Available Today’s market in micro-wind turbines is in constant development introducing more efficient solutions for the future. Besides the private use of tower supported turbines, opportunities to integrate wind turbines in the built environment arise. The Integrated Roof Wind Energy System (IRWES presented in this work is a modular roof structure integrated on top of existing or new buildings. IRWES is build up by an axial array of skewed shaped funnels used for both wind inlet and outlet. This inventive use of shape and geometry leads to a converging air capturing inlet to create high wind mass flow and velocity toward a Vertical Axis Wind Turbine (VAWT in the center-top of the roof unit for the generation of a relatively high amount of energy. The scope of this research aims to make an optimized structural design of IRWES to be placed on top of the Vertigo building in Eindhoven; analysis of the structural performance; and impact to the existing structure by means of Finite Element Modeling (FEM. Results show that the obvious impact of wind pressure to the structural design is easily supported in different configurations of fairly simple lightweight structures. In particular, the weight addition to existing buildings remains minimal.

  17. Integration of large wind farms into weak power grids. Emphasis on the Ethiopian interconnected system (ICS)

    Energy Technology Data Exchange (ETDEWEB)

    Bantyirga Gessesse, Belachew

    2013-07-18

    The impact of increased wind power on the steady state and dynamic behavior of the Ethiopian power system is the main focus of this thesis. The integration of wind power to the existing grid with conventional generators introduces new set of challenges regarding system security and operational planning, the main cause of the difference arising from the uncertainty of the primary source of energy and the response time following a disturbance. For incorporating wind turbine models into the overall dynamic model of the system and investigating the effect of wind on the dynamic behavior of the wind first models of wind turbine components were put together by reviewing the current state of the art in wind turbine modeling and control concepts. The theoretical insight thus gained was applied to the Ethiopian power system as a case study. Since the models of the installed turbines were either not available or incomplete, an alternative modeling approach based on generic models was adopted. The generic model, in addition to obviating the need for technology or manufacturer specific models, reduces the complexity the dynamic model. Using this procedure, generic dynamic models for wind farm in the system were developed. The capability of dynamic models to reproduce the dynamic response of the system has been verified by comparing simulation results obtained with a detailed and generic wind farm model. It could be shown that the generic wind turbine model is simple, but accurate enough to represent any wind turbine types or entire wind farms for power system stability analysis. The next task was the study of the effect of increased wind power level on the general behavior of the Ethiopian system. It is observed that overall the impact of wind turbines on the operational indices of the system was -as could be expected- more pronounced in the vicinity of the wind farm. But the power angle oscillation following a disturbance was observed across the whole system. Further, as a

  18. THE INFLUENCE OF BUOYANCY ON FLOW AND POLLUTANT DISPERSION IN STREET CANYONS

    OpenAIRE

    Buccolieri, Riccardo; Pulvirenti, Beatrice; Di Sabatino, Silvana; Britter, Rex

    2008-01-01

    Abstract: In this paper, the effect of buoyancy on flow and pollutant dispersion within street canyons is studied by means of computational fluid dynamics simulations. We consider a neutral boundary layer approaching a 3D street canyon assuming a wind direction perpendicular to the street canyon. The Boussinesq hypothesis for incompressible fluids is chosen for modelling buoyancy. We distinguish three cases: leeward, ground and windward wall heating. Thermal effects on both the flow ...

  19. Trees in urban street canyons and their impact on the dispersion of automobile exhausts

    OpenAIRE

    Gromke, Christof; Ruck, Bodo

    2007-01-01

    The aim of the present study is to clarify the influence of trees on the dispersion of automobile exhausts in urban street canyons. For this purpose, measurements have been performed with a small scale wind tunnel model of an idealized, isolated street canyon with model trees placed along the canyon center axis. Sulfur hexafluoride (SF6) was released from a line source embedded in the street surface, simulating vehicle exhaust emissions. The influence of various tree planting arrangements on ...

  20. Thermoplastic Composite Wind Turbine Blades: An Integrated Design Approach

    NARCIS (Netherlands)

    Joncas, S.

    2010-01-01

    This thesis proposes a new structural design concept for future large wind turbine blades based on fully recyclable thermoplastic composites (TPC). With respect to material properties, cost and processing, reactively processed anionic polyamide-6 (APA-6) has been identified as the most promising the

  1. Review of VSC HVDC Connection for Offshore Wind Power Integration

    DEFF Research Database (Denmark)

    Korompili, Asimenia; Wu, Qiuwei; Zhao, Haoran

    2016-01-01

    Voltage Source Converter (VSC) High Voltage Direct Current (HVDC) connection has become a new trend for long distance offshore wind power transmission. It has been confirmed by a lot of research that the maximum distance of a High Voltage Alternative Current (HVAC) sub-marine cable transmission s...

  2. Western Wind and Solar Integration Study: Executive Summary

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2010-05-01

    This Study investigates the operational impact of up to 35% energy penetration of wind, photovoltaics (PVs), and concentrating solar power (CSP) on the power system operated by the WestConnect group of utilities in Arizona, Colorado, Nevada, New Mexico, and Wyoming.

  3. Strategic Demand-Side Response to Wind Power Integration

    DEFF Research Database (Denmark)

    Daraeepour, Ali; Kazempour, Seyyedjalal; Patiño-Echeverri, Dalia;

    2015-01-01

    This paper explores the effects of allowing large, price-responsive consumers to provide reserves in a power system with significant penetration of wind energy. A bilevel optimization model represents the utility maximization problem of a large consumer, subject to a stochastic day-ahead co-optim...

  4. Impacts of large-scale offshore wind farm integration on power systems through VSC-HVDC

    DEFF Research Database (Denmark)

    Liu, Hongzhi; Chen, Zhe

    2013-01-01

    The potential of offshore wind energy has been commonly recognized and explored globally. Many countries have implemented and planned offshore wind farms to meet their increasing electricity demands and public environmental appeals, especially in Europe. With relatively less space limitation......, an offshore wind farm could have a capacity rating to hundreds of MWs or even GWs that is large enough to compete with conventional power plants. Thus the impacts of a large offshore wind farm on power system operation and security should be thoroughly studied and understood. This paper investigates...... the impacts of integrating a large-scale offshore wind farm into the transmission system of a power grid through VSC-HVDC connection. The concerns are focused on steady-state voltage stability, dynamic voltage stability and transient angle stability. Simulation results based on an exemplary power system...

  5. Impacts of large scale integration of wind power into the power system of British Columbia

    Energy Technology Data Exchange (ETDEWEB)

    Broeer, Torsten; Djilali, Ned; Rowe, Andrew [Victoria Univ., BC (Canada). Inst. for Integrated Energy Systems; Victoria Univ., BC (Canada). Dept. of Mechanical Engineering

    2009-07-01

    This paper provides an overview of the impacts of increasing the contribution of wind energy to British Columbia's power generation and transmission system. A model has been developed utilizing wind energy data provided by BC Hydro, the power generating authority in the province. These wind profiles were superimposed on the British Columbia Power System. The model incorporates various wind penetration scenarios and utility assumptions regarding load growth over the next 10 years. The objectives are to determine optimal strategies that integrate wind energy generation into the power system while maintaining or improving system reliability. The simulations were conducted using MATPOWER functionality within MATLAB. The results are based on a simplified representation of British Columbia's power system and incorporate optimal power flow with unit commitment optimization. (orig.)

  6. Integrating Systems Health Management with Adaptive Controls for a Utility-Scale Wind Turbine

    Science.gov (United States)

    Frost, Susan A.; Goebel, Kai; Trinh, Khanh V.; Balas, Mark J.; Frost, Alan M.

    2011-01-01

    Increasing turbine up-time and reducing maintenance costs are key technology drivers for wind turbine operators. Components within wind turbines are subject to considerable stresses due to unpredictable environmental conditions resulting from rapidly changing local dynamics. Systems health management has the aim to assess the state-of-health of components within a wind turbine, to estimate remaining life, and to aid in autonomous decision-making to minimize damage. Advanced adaptive controls can provide the mechanism to enable optimized operations that also provide the enabling technology for Systems Health Management goals. The work reported herein explores the integration of condition monitoring of wind turbine blades with contingency management and adaptive controls. Results are demonstrated using a high fidelity simulator of a utility-scale wind turbine.

  7. Integrating massiv wind power in the electric system. Acciona experience in Spain

    Energy Technology Data Exchange (ETDEWEB)

    Giraut Ruso, E.; Ruiz Guillen, J.; Quinonez-Varela, G.; Armendariz Otazu, I.; Navarrete Pablo-Romero, A.; Moreira Prada, C.; Alday Aracama, G.; Sanchez Ardoiz, R.; Moreno Fernandez, J. [Acciona Energia, Sarriguren (Spain)

    2009-07-01

    In this paper, the existing operational procedures applicable to wind and renewable generation in Spain are presented. These include remote control of renewable generators and their interaction with the TSO's Control Centre: energy production forecast and market integration, and voltage and reactive power control. Acciona Energia, as one of the largest operator and owner of renewable assets in Spain (particularly wind power plants), hat been a major player in the implementation of measures to comply with these procedures. For instance, it has worked closely with the TSO and the wind sector to help formulating Grid Code requirements, it has designed new wind turbine technologies to fulfil them and it has deployed innovative solutions to adapt older wind generators and plants to new standards (retrofitting). Acciona's experiences and technical solutions to these challenges are thoroughly discussed. (orig.)

  8. Large-scale integration of wind power into the existing Chinese energy system

    DEFF Research Database (Denmark)

    Liu, Wen; Lund, Henrik; Mathiesen, Brian Vad

    2011-01-01

    This paper presents the ability of the existing Chinese energy system to integrate wind power and explores how the Chinese energy system needs to prepare itself in order to integrate more fluctuating renewable energy in the future. With this purpose in mind, a model of the Chinese energy system has...... been constructed by using EnergyPLAN based on the year 2007, which has then been used for investigating three issues. Firstly, the accuracy of the model itself has been examined and then the maximum feasible wind power penetration in the existing energy system has been identified. Finally, barriers...... stability, the maximum feasible wind power penetration in the existing Chinese energy system is approximately 26% from both technical and economic points of view. A fuel efficiency decrease occurred when increasing wind power penetration in the system, due to its rigid power supply structure and the task...

  9. Ancillary services and the integration of substantial quantities of wind power

    DEFF Research Database (Denmark)

    Østergaard, Poul Alberg

    2006-01-01

    as the potential impact of heat pumps used for district heating and installed for integration purposes. The analyses are made with particular focus on grid stability and delivery of ancillary services (required to control voltage and frequency) and demonstrate that it is possible to accommodate 50% or more wind......Denmark has the World’s highest penetration of grid connected wind power in electricity generation with a share of 15.0% of total domestic demand in 2002 [Danish Energy Authority. Rapport fra arbejdsgruppen om kraftvarme- og VE-elektricitet. Bilagsrapport. Copenhagen: Danish Energy Authority; 2001...... system. This combination of wind power and CHP is a challenge for system operators but also gives opportunities. This article analyses the possibilities for integrating even more wind power using new power balancing strategies that exploit the possibilities given by the existence of CHP plants as well...

  10. Wind power and market integration, comparative study of financing schemes

    International Nuclear Information System (INIS)

    The financing scheme of renewable energies is a key factor for their development pace and cost. As some countries like France, Germany or Spain have chosen a Feed-in Tariff (FiT) scheme, there are in fact four possible financing schemes: FiT, ex-post prime, ex-ante prime, and quotas (green certificates). A market convergence is then supposed to meet two main objectives: the control of market distortions related to wind energy development, and the optimization of wind energy production with respect to market signals. The authors analyse the underlying economic challenges and the ability of financing schemes to meet these objectives within a short term horizon (2015). They present the different financing schemes, analyse the impact of three key economic factors (market distortion, production optimization, financing costs)

  11. Minimum Load-curtailment in Transmission Network Planning Considering Integrated Wind Farms

    Institute of Scientific and Technical Information of China (English)

    CHEN Yan; WEN Jinyu; CHENG Shijie

    2011-01-01

    With the enlarging scale of integrated wind power, the transmission network expansion planning (TNEP) problem considering wind farms is more important than before. TNEP problem usually can be divided into two sub-problems. The first sub-problem is to determine the new planning scheme in some way, and the second sub-problem is to assess the security and reliability of the transmission network planning scheme using the minimum load-shedding index.

  12. Electricity storage. A solution for wind power integration? Study on the economic and institutional aspects of the implementation of electricity storage for the integration of wind power

    International Nuclear Information System (INIS)

    In today's society a power outage can lead to major financial damage. It is therefore of high importance that the electricity system is reliable and that customers can rely on high security of supply. To prevent power outages, the electricity system has to be in balance continuously: supply and load have to be equal. Currently the majority of the electricity generation is done by conventional power plants of which the operation schedule is fully controllable. This means that these plants can be operated in such a way that electricity demand, which varies during the day, can be met continuously. The integration of a large share of wind power in the electricity supply system however, can lead to problems with respect to the balancing of the electricity system. This is caused by the fact that wind power has an intermittent character. Its production fluctuates and is uncertain: it therefore cannot be used to follow the varying load. Electricity storage could contribute to the integration of wind power in the electricity supply system. Storage systems can decouple the timing of generation and consumption of electricity and can therefore compensate for the fluctuations in wind power production. This investigation aims at identifying what problems the integration of a large share of wind power will cause and how electricity storage can resolve these problems. Subsequently, the implementation costs of storage systems for the identified applications will be investigated. Finally, the current regulatory environment will be discussed to evaluate whether it is geared to the implementation of electricity storage. Therefore, the following research question is formulated: Under which technological and institutional preconditions will it be advantageous to implement electricity storage systems, in combination with wind farms, in the next 20 years? To answer the research question the following subquestions have been formulated: (1) What are the implications of the market design on

  13. Grid Integration of Offshore Wind Farms using Hybrid HVDC Transmission: Control and Operational Characteristics

    OpenAIRE

    Olguin, Raymundo E. Torres

    2013-01-01

    The transmission of offshore wind energy is one of the most relevant challenges since the best wind conditions are located far from shore. High-voltage DC (HVDC) is the most feasible option for the grid integration of offshore wind farms if the distance to shore is relatively long. Currently, there are two different HVDC technologies: current source converter (CSC)-based HVDC and voltage source converter (VSC)-based HVDC. Among CSCs, the line-commutated converter (LCC)-based HVDC is a well es...

  14. Wind power integration into the automatic generation control of power systems with large-scale wind power

    Directory of Open Access Journals (Sweden)

    Abdul Basit

    2014-10-01

    Full Text Available Transmission system operators have an increased interest in the active participation of wind power plants (WPP in the power balance control of power systems with large wind power penetration. The emphasis in this study is on the integration of WPPs into the automatic generation control (AGC of the power system. The present paper proposes a coordinated control strategy for the AGC between combined heat and power plants (CHPs and WPPs to enhance the security and the reliability of a power system operation in the case of a large wind power penetration. The proposed strategy, described and exemplified for the future Danish power system, takes the hour-ahead regulating power plan for generation and power exchange with neighbouring power systems into account. The performance of the proposed strategy for coordinated secondary control is assessed and discussed by means of simulations for different possible future scenarios, when wind power production in the power system is high and conventional production from CHPs is at a minimum level. The investigation results of the proposed control strategy have shown that the WPPs can actively help the AGC, and reduce the real-time power imbalance in the power system, by down regulating their production when CHPs are unable to provide the required response.

  15. Optimal Real-Time Scheduling of Wind Integrated Power System Presented with Storage and Wind Forecast Uncertainties

    Directory of Open Access Journals (Sweden)

    Yuchong Huo

    2015-02-01

    Full Text Available The volatility of wind power poses great challenges to the operation of power systems. This paper deals with the economic dispatch problems presented by energy storage in wind integrated systems. A policy iteration algorithm for deriving the cost optimal policy of real-time scheduling is proposed, taking the effect of wind forecast uncertainties into account. First, energy loss and use of fast-ramping generation are selected as the performance metrics. Then, a policy iteration algorithm is developed using the Perturbed Markov decision process. This algorithm has a two-level optimization structure in which both the long-term and short-term behaviors of real-time scheduling policy are optimized. In addition, a unified optimal storage control strategy is presented. The feasibility of the proposed methodology is demonstrated via the wind power archive of Electric Reliability Council of Texas (ERCOT. Through comparative numerical experiments, both the performance of the policy iteration algorithm in the short-term and long-term are verified and the consistency, robustness, good convergence and high computational efficiency of the proposed algorithm are also corroborated.

  16. Multilink DC Transmission for Offshore Wind Power Integration

    DEFF Research Database (Denmark)

    Craciun, Bogdan-Ionut; Silva, Rodrigo Da; Teodorescu, Remus;

    2012-01-01

    The High Voltage Direct Current (HVDC) system gains much more flexibility on a basis of multi terminal operation. Having extra converters brings also new ideas in sharing the active power and one of the solutions is the use of virtual impedance correlated with a droop controller. This paper...... analysis the Multi Terminal Direct Current (MTDC) operation and focuses on the sharing of active power produced by an offshore Wind Power Plant (WPP). The first objective was to model the system in PSCAD/EMTDC simulation software and then control structure tested under different situations. The second...

  17. Integration of permanent magnet synchronous generator wind turbines into power grid

    Science.gov (United States)

    Abedini, Asghar

    , integrating energy storage systems with wind farms has attracted a lot of attention. These two subjects are addressed in this dissertation in detail. Permanent Magnet Synchronous Generators (PMSG) are used in variable speed wind turbines. In this thesis, the dynamic of the PMSG is investigated and a power electronic converter is designed to integrate the wind turbine to the grid. The risks of PMSG wind turbines such as low voltage ride through and short circuits, are assessed and the methods of mitigating the risks are discussed. In the second section of the thesis, various methods of smoothing wind turbine output power are explained and compared. Two novel methods of output power smoothing are analyzed: Rotor inertia and Super capacitors. The advantages and disadvantages of each method are explained and the dynamic model of each method is developed. The performance of the system is evaluated by simulating the wind turbine system in each method. The concepts of the methods of smoothing wind power can be implemented in other types of wind turbines such as Doubly Fed Induction Generator (DFIG) wind turbines.

  18. A stochastic framework for the grid integration of wind power using flexible load approach

    International Nuclear Information System (INIS)

    Highlights: • This paper focuses on the potential of Demand Response Programs (DRPs) to contribute to flexibility. • A stochastic network constrained unit commitment associated with DR is presented. • DR participation levels and electricity tariffs are evaluated on providing a flexible load profile. • Novel quantitative indices for evaluating flexibility are defined to assess the success of DRPs. • DR types and customer participation levels are the main factors to modify the system load profile. - Abstract: Wind power integration has always been a key research area due to the green future power system target. However, the intermittent nature of wind power may impose some technical and economic challenges to Independent System Operators (ISOs) and increase the need for additional flexibility. Motivated by this need, this paper focuses on the potential of Demand Response Programs (DRPs) as an option to contribute to the flexible operation of power systems. On this basis, in order to consider the uncertain nature of wind power and the reality of electricity market, a Stochastic Network Constrained Unit Commitment associated with DR (SNCUCDR) is presented to schedule both generation units and responsive loads in power systems with high penetration of wind power. Afterwards, the effects of both price-based and incentive-based DRPs are evaluated, as well as DR participation levels and electricity tariffs on providing a flexible load profile and facilitating grid integration of wind power. For this reason, novel quantitative indices for evaluating flexibility are defined to assess the success of DRPs in terms of wind integration. Sensitivity studies indicate that DR types and customer participation levels are the main factors to modify the system load profile to support wind power integration

  19. A modelling exercise to examine variations of NOx concentrations on adjacent footpaths in a street canyon: The importance of accounting for wind conditions and fleet composition.

    Science.gov (United States)

    Gallagher, J

    2016-04-15

    Personal measurement studies and modelling investigations are used to examine pollutant exposure for pedestrians in the urban environment: each presenting various strengths and weaknesses in relation to labour and equipment costs, a sufficient sampling period and the accuracy of results. This modelling exercise considers the potential benefits of modelling results over personal measurement studies and aims to demonstrate how variations in fleet composition affects exposure results (presented as mean concentrations along the centre of both footpaths) in different traffic scenarios. A model of Pearse Street in Dublin, Ireland was developed by combining a computational fluid dynamic (CFD) model and a semi-empirical equation to simulate pollutant dispersion in the street. Using local NOx concentrations, traffic and meteorological data from a two-week period in 2011, the model were validated and a good fit was presented. To explore the long-term variations in personal exposure due to variations in fleet composition, synthesised traffic data was used to compare short-term personal exposure data (over a two-week period) with the results for an extended one-year period. Personal exposure during the two-week period underestimated the one-year results by between 8% and 65% on adjacent footpaths. The findings demonstrate the potential for relative differences in pedestrian exposure to exist between the north and south footpaths due to changing wind conditions in both peak and off-peak traffic scenarios. This modelling approach may help overcome potential under- or over-estimations of concentrations in personal measurement studies on the footpaths. Further research aims to measure pollutant concentrations on adjacent footpaths in different traffic and wind conditions and to develop a simpler modelling system to identify pollutant hotspots on our city footpaths so that urban planners can implement improvement strategies to improve urban air quality. PMID:26859699

  20. A modelling exercise to examine variations of NOx concentrations on adjacent footpaths in a street canyon: The importance of accounting for wind conditions and fleet composition.

    Science.gov (United States)

    Gallagher, J

    2016-04-15

    Personal measurement studies and modelling investigations are used to examine pollutant exposure for pedestrians in the urban environment: each presenting various strengths and weaknesses in relation to labour and equipment costs, a sufficient sampling period and the accuracy of results. This modelling exercise considers the potential benefits of modelling results over personal measurement studies and aims to demonstrate how variations in fleet composition affects exposure results (presented as mean concentrations along the centre of both footpaths) in different traffic scenarios. A model of Pearse Street in Dublin, Ireland was developed by combining a computational fluid dynamic (CFD) model and a semi-empirical equation to simulate pollutant dispersion in the street. Using local NOx concentrations, traffic and meteorological data from a two-week period in 2011, the model were validated and a good fit was presented. To explore the long-term variations in personal exposure due to variations in fleet composition, synthesised traffic data was used to compare short-term personal exposure data (over a two-week period) with the results for an extended one-year period. Personal exposure during the two-week period underestimated the one-year results by between 8% and 65% on adjacent footpaths. The findings demonstrate the potential for relative differences in pedestrian exposure to exist between the north and south footpaths due to changing wind conditions in both peak and off-peak traffic scenarios. This modelling approach may help overcome potential under- or over-estimations of concentrations in personal measurement studies on the footpaths. Further research aims to measure pollutant concentrations on adjacent footpaths in different traffic and wind conditions and to develop a simpler modelling system to identify pollutant hotspots on our city footpaths so that urban planners can implement improvement strategies to improve urban air quality.

  1. Tools and concepts to integrate German offshore wind potential into electrical energy supply

    Energy Technology Data Exchange (ETDEWEB)

    Rohrig, K.; Hoppe-Kilpper, M. [Institut fuer Solare Energieversorgungstechnik (ISET), Kassel (Germany); Sassnick, Y. [Vattenfall Europe Transmission GmbH (Germany); Fischer, F.; Hartge, S. [ENERCON GmbH, Aurich (Germany); Winter, W.; Hofmann, L. [E.ON-Netz GmbH, Lehrte (Germany); Heier, S.; Valov, B. [Kassel Univ. (Gesamthochschule) (Germany); Biermann, K. [Deutscher Wetterdienst, Hamburg (Germany)

    2005-07-01

    The paper describes the technical status and presents new concepts, models and approaches for the technical assistance of large scale wind power integration into the electrical energy supply system in Germany. It shows the technical and economic problems with the integration of high penetration of wind power plant in the network and the total electrical system. After an analysis of the effects of increased wind power generation on system planning and grid operation, we discuss innovative operational control concepts for large (offshore) wind farms. These concepts will provide a multitude of new possibilities to enable simple, flexible and undisturbed reaction to the demands of participants (wind farm operators, grid operators). These operational control strategies are mainly based on ISETs successful employed wind power prediction tools, operated by E.ON Netz (ENE), Vattenfall Europe Transmission (VE-T), RWE Transportnetz Strom (RWE) and will enable energy and power control, as well as the provision of reactive power, in order to achieve comparable properties to conventional power plant types. (orig.)

  2. An integrated methodology on the suitability of offshore sites for wind farm development

    Science.gov (United States)

    Patlakas, Platon; Galanis, George; Péray, Marie; Filipot, Jean-François; Kalogeri, Christina; Spyrou, Christos; Diamantis, Dimitris; Kallos, Gerorge

    2016-04-01

    During, the last decades the potential and interest in wind energy investments has been constantly increasing in the European countries. As technology changes rapidly, more and more areas can be identified as suitable for energy applications. Offshore wind farms perfectly illustrate how new technologies allow to build bigger, more efficient and resistant in extreme conditions wind power plants. The current work proposes an integrated methodology to determine the suitability of an offshore marine area for the development of wind farm structures. More specifically, the region of interest is evaluated based both on the natural resources, connected to the local environmental characteristics, and potential constrains set by anthropogenic or other activities. State of the art atmospheric and wave models and a 10-year hindcast database are utilized in conjunction with local information for a number of potential constrains, leading to a 5-scale suitability index for the whole area. In this way, sub regions are characterized, at a high resolution mode, as poorly or highly suitable for wind farm development, providing a new tool for technical/research teams and decision makers. In addition, extreme wind and wave conditions and their 50-years return period are analyzed and used to define the safety level of the wind farms structural characteristics.

  3. Western Wind and Solar Integration Study Phase 3 – Frequency Response and Transient Stability

    Energy Technology Data Exchange (ETDEWEB)

    Miller, N. W. [GE Energy Management, Schenectady, NY (United States); Shao, M. [GE Energy Management, Schenectady, NY (United States); Pajic, S. [GE Energy Management, Schenectady, NY (United States); D' Aquila, R. [GE Energy Management, Schenectady, NY (United States)

    2014-12-01

    Power system operators and utilities worldwide have concerns about the impact of high-penetration wind and solar generation on electric grid reliability (EirGrid 2011b, Hydro-Quebec 2006, ERCOT 2010). The stability of North American grids under these conditions is a particular concern and possible impediment to reaching future renewable energy goals. Phase 3 of the Western Wind and Solar Integration Study (WWSIS-3) considers a 33% wind and solar annual energy penetration level that results in substantial changes to the characteristics of the bulk power system, including different power flow patterns, different commitment and dispatch of existing synchronous generation, and different dynamic behavior of wind and solar generation. WWSIS-3 evaluates two specific aspects of fundamental frequency system stability: frequency response and transient stability.

  4. Large-scale integration of wind power into different energy systems

    DEFF Research Database (Denmark)

    Lund, Henrik

    2005-01-01

    The paper presents the ability of different energy systems and regulation strategies to integrate wind power. The ability is expressed by the following three factors: the degree of electricity excess production caused by fluctuations in wind and Combined Heat and Power (CHP) heat demands......, the ability to utilise wind power to reduce CO2 emission in the system, and the ability to benefit from exchange of electricity on the market. Energy systems and regulation strategies are analysed in the range of a wind power input from 0 to 100% of the electricity demand. Based on the Danish energy system...... and such potential future energy systems different regulation strategies have been analysed, i.e. the inclusion of small CHP plants into the regulation task of electricity balancing and ancillary grid stability services and investments in electric heating, heat pumps and heat storage capacity. The results...

  5. Full-Scale Field Test of a Blade-Integrated Dual-Telescope Wind Lidar

    DEFF Research Database (Denmark)

    Pedersen, Anders Tegtmeier; Sjöholm, Mikael; Angelou, Nikolas;

    -dimensional plane upwind was installed in the turbine and the first results from these experiments will be presented in another EWEA 2013 contribution. The lidar logged the raw Doppler spectra and the wind speed estimation was done subsequently using software designed specifically for the blade-mounted lidar...... in the top and bottom of the rotor plane. Conclusion We present here what we believe is the first successful wind speed measurements from a dual-telescope lidar installed on the blade of an operating wind turbine. The full-scale field test performed in the summer of 2012 has clearly demonstrated...... for load reduction and power optimization. To date, main attention has been on control schemes where measurements of wind speeds and direction upwind are used for yaw and speed corrections. In this study we investigate experimentally the feasibility of using lidars integrated in the turbine blades...

  6. Large-scale wind power integration in Norway and impact on damping in the Nordic grid

    Science.gov (United States)

    Hagstrøm, Espen; Norheim, Ian; Uhlen, Kjetil

    2005-07-01

    The Nordic energy market is in need of new power generation capacity. Norway is today in shortage of electrical energy, and the hydropower-based system must rely on importing electrical power from its neighbours in a normal year of hydro inflow. One solution to this problem is to invest in new generation capacity, e.g. by integrating more wind power into the Norwegian grid. The Norwegian government has announced that 1000 MW of wind power will be installed in Norway by 2010, corresponding to an eventual energy production of approximately 3 TWh year-1. This article investigates the impact of wind power integration in Norway on the damping of interarea mode oscillations in the Nordic grid. The impact on the interarea mode oscillations is tested for various types of generators. Results from computer analyses of a simplified yet realistic equivalent of the Nordic power system are used to compute the interarea mode oscillations. Copyright

  7. Multiple Timescale Dispatch and Scheduling for Stochastic Reliability in Smart Grids with Wind Generation Integration

    OpenAIRE

    He, Miao; Murugesan, Sugumar; Zhang, Junshan

    2010-01-01

    Integrating volatile renewable energy resources into the bulk power grid is challenging, due to the reliability requirement that at each instant the load and generation in the system remain balanced. In this study, we tackle this challenge for smart grid with integrated wind generation, by leveraging multi-timescale dispatch and scheduling. Specifically, we consider smart grids with two classes of energy users - traditional energy users and opportunistic energy users (e.g., smart meters or sm...

  8. An integrated assessment for wind energy in Lake Michigan coastal counties.

    Science.gov (United States)

    Nordman, Erik; VanderMolen, Jon; Gajewski, Betty; Isely, Paul; Fan, Yue; Koches, John; Damm, Sara; Ferguson, Aaron; Schoolmaster, Claire

    2015-04-01

    The benefits and challenges of onshore and offshore wind energy development were assessed for a 4-county area of coastal Michigan. Economic, social, environmental, and spatial dimensions were considered. The coastal counties have suitable wind resources for energy development, which could contribute toward Michigan's 10% renewable energy standard. Wind energy is cost-effective with contract prices less than the benchmark energy price of a new coal-fired power plant. Constructing a 100 MW wind farm could have a $54.7 million economic impact. A patchwork of township-level zoning ordinances regulates wind energy siting. Voluntary collaborations among adjacent townships standardizing the ordinances could reduce regulatory complexity. A Delphi Inquiry on offshore wind energy in Lake Michigan elicited considerable agreement on its challenges, but little agreement on the benefits to coastal communities. Offshore turbines could be acceptable to the participants if they reduced pollution, benefited coastal communities, involved substantial public participation, and had minimal impact on property values and tourism. The US Coast Guard will take a risk-based approach to evaluating individual offshore developments and has no plans to issue blanket restrictions around the wind farms. Models showed that using wind energy to reach the remainder of the 10% renewable energy standard could reduce SO2 , NOx , and CO2 pollution by 4% to 7%. Turbines are highly likely to impact the area's navigational and defense radar systems but planning and technological upgrades can reduce the impact. The integrated assessment shows that responsible wind energy development can enhance the quality of life by reducing air pollution and associated health problems and enhancing economic development. Policies could reduce the negative impacts to local communities while preserving the benefits to the broader region.

  9. Wind power integration with heat pumps, heat storages, and electric vehicles – Energy systems analysis and modelling

    OpenAIRE

    Hedegaard, Karsten; Morthorst, Poul Erik; Münster, Marie; Detlefsen, Nina

    2013-01-01

    The fluctuating and only partly predictable nature of wind challenges an effective integration of large wind power penetrations. This PhD thesis investigates to which extent heat pumps, heat storages, and electric vehicles can support the integration of wind power. Considering the gaps in existing research, main focus is put on individual heat pumps in the residential sector and the possibilities for flexible operation, using the heat storage options available. Extensive model development is...

  10. Offshore system for integration of the wind energy; Sistema offshore para integracao de energia eolica

    Energy Technology Data Exchange (ETDEWEB)

    Decker, Jan de [3E, Brussels (Belgium); Tambke, Jens [Universidade de Oldemburg (Germany). ForWind; Voelker, J. [Dena - Agencia Alema de Energia (Germany); Michalowska-Knap, Katarzyna [Instituto de Energia Renovavel (Poland)

    2010-09-15

    The Offshore Grid project aims to analyze the conditions required for the development of an offshore transmission network to integrate renewable energy (wind) to the national electrical systems, securely and efficiently. Regulatory aspects, technical, economic and political are considered, that will help the various players in the industry to have a common view on the offshore power grids in Europe.

  11. Modeling for high-level studies of wind resource integrations to the main grids

    Energy Technology Data Exchange (ETDEWEB)

    Arabi, S.; Moshref, A. [Powertech Labs Inc., Surrey, BC (Canada)

    2009-07-01

    This presentation discussed modeling issues for high-level system planning assessment of power transmission systems that are integrated with various levels of wind generation. The study involved various point of interconnection (POI) locations and voltage and transient security simulations using Powertech's DSATools software. The two-stage approach identified potential transmission capabilities to accommodate new wind generations with no reinforcement to the existing system beyond the POI. It also identified potential feasible short-term system reinforcements, such as upgrading existing lines, series compensation, and FACTS controllers, to allow higher levels of wind generation integration. The presentation discussed special models and assumptions related to wind power plants alternating current/direct current interconnections; wind turbine generators and transformers; shunt reactive resources at farm collector/POI; FACTS controllers; series compensation schemes; and shunt reactor control schemes. Applied criteria and contingencies and transfer were also presented along with simulated scenarios. It was concluded that for a series-compensated radial connection with single pole switching and re-close, it is crucial to avoid any bypassing of the capacitor banks in the healthy poles. 7 figs.

  12. A new simulation approach for the assessment of wind integration impacts on system operations

    Energy Technology Data Exchange (ETDEWEB)

    Montigny, Martin de; Heniche, Anissa; Kamwa, Innocent [Hydro-Quebec/IREQ, Varennes, QC (Canada); Sauriol, Robert; Mailhot, Richard; Lefebvre, Daniel [Hydro-Quebec TransEnergie, Montreal, QC (Canada). Bulk and Interconnections Network Strategies Dept.

    2010-07-01

    With the increase of wind power penetration in power systems, operators face new challenges in order to maintain network reliability. Indeed, the greater variability and lesser predictability of this variable energy source put additional pressure on the frequency regulation reserves. This paper aims at assessing, on Hydro-Quebec network, of wind integration impacts on Automatic Generation Control (AGC), on Load-Following, on the number of additional alternators start-ups and shut-downs and on the number of interrupted exports/imports. The considered wind power is equal to 3000MW. In this paper, the regulation signals are obtained using a network operation simulation approach. In other words, by using a AC power flow, a simulator called SIRE, developed at Hydro-Quebec (IREQ), allows the accurate simulation of the hourly forecast process and real-time network operation, with or without wind power. The impacts on AGC and Load-Following, obtained by simulation, are compared to those evaluated using two statistical based approaches. The first is a covariance sharing allocation concept proposed by BPA (Bonneville Power Administration). The second one is the standard deviation increase approach developed by ORNL (Oak Ridge National Laboratory). The obtained results show the efficiency of SIRE simulator in order to quantify the impacts of wind integration. (orig.)

  13. Large-scale integration of wind power into different energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Lund, H. [Aalborg University (Denmark). Dept. of Development and Planning

    2005-10-01

    The paper presents the ability of different energy systems and regulation strategies to integrate wind power. The ability is expressed by the following three factors: the degree of electricity excess production caused by fluctuations in wind and Combined Heat and Power (CHP) heat demands, the ability to utilise wind power to reduce CO{sub 2} emission in the system, and the ability to benefit from exchange of electricity on the market. Energy systems and regulation strategies are analysed in the range of a wind power input from 0 to 100% of the electricity demand. Based on the Danish energy system, in which 50% of the electricity demand is produced in CHP, a number of future energy systems with CO{sub 2} reduction potentials are analysed, i.e. systems with more CHP, systems using electricity for transportation (battery or hydrogen vehicles) and systems with fuel-cell technologies. For the present and such potential future energy systems different regulation strategies have been analysed, i.e. the inclusion of small CHP plants into the regulation task of electricity balancing and ancillary grid stability services and investments in electric heating, heat pumps and heat storage capacity. The results of the analyses make it possible to compare short-term and long-term potentials of different strategies of large-scale integration of wind power. (author)

  14. Four essays on offshore wind power potential, development, regulatory framework, and integration

    Science.gov (United States)

    Dhanju, Amardeep

    . It outlines a regulatory framework touching on key elements such as the leasing system, length of tenure, and financial terms for allocating property rights. In addition, the framework also provides recommendations on environmental assessment that would be required prior to lease issuance. The fourth essay analyzes offshore wind power integration using electric thermal storage in housing units. It presents a model of wind generation, heating load and wind driven thermal storage to assess the potential of storage to buffer wind intermittency. The analysis suggests that thermal load matches the seasonal excess of offshore wind during winter months, and that electric thermal storage could provide significant temporal, spatial, and cost advantages for balancing output from offshore wind generation, while also converting a major residential load (space heating) now met by fossil fuels to low carbon energy resources. Together, the four essays provide new analyses of policy, regulatory, and system integration issues that could impede resource development, and also analyze and recommend strategies to manage these issues.

  15. Energy System Analysis of Large-Scale Integration of Wind Power

    International Nuclear Information System (INIS)

    The paper presents the results of two research projects conducted by Aalborg University and financed by the Danish Energy Research Programme. Both projects include the development of models and system analysis with focus on large-scale integration of wind power into different energy systems. Market reactions and ability to exploit exchange on the international market for electricity by locating exports in hours of high prices are included in the analyses. This paper focuses on results which are valid for energy systems in general. The paper presents the ability of different energy systems and regulation strategies to integrate wind power, The ability is expressed by three factors: One factor is the degree of electricity excess production caused by fluctuations in wind and CHP heat demands. The other factor is the ability to utilise wind power to reduce CO2 emission in the system. And the third factor is the ability to benefit from exchange of electricity on the market. Energy systems and regulation strategies are analysed in the range of a wind power input from 0 to 100% of the electricity demand. Based on the Danish energy system, in which 50 per cent of the electricity demand is produced in CHP, a number of future energy systems with CO2 reduction potentials are analysed, i.e. systems with more CHP, systems using electricity for transportation (battery or hydrogen vehicles) and systems with fuel-cell technologies. For the present and such potential future energy systems different regulation strategies have been analysed, i.e. the inclusion of small CHP plants into the regulation task of electricity balancing and grid stability and investments in electric heating, heat pumps and heat storage capacity. Also the potential of energy management has been analysed. The results of the analyses make it possible to compare short-term and long-term potentials of different strategies of large-scale integration of wind power

  16. Western Wind and Solar Integration Study Phase 3A: Low Levels of Synchronous Generation

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Nicholas W. [GE Energy Management, Atlanta, GA (United States); Leonardi, Bruno [GE Energy Management, Atlanta, GA (United States); D' Aquila, Robert [GE Energy Management, Atlanta, GA (United States); Clark, Kara [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2015-11-17

    The stability of the North American electric power grids under conditions of high penetrations of wind and solar is a significant concern and possible impediment to reaching renewable energy goals. The 33% wind and solar annual energy penetration considered in this study results in substantial changes to the characteristics of the bulk power system. This includes different power flow patterns, different commitment and dispatch of existing synchronous generation, and different dynamic behavior from wind and solar generation. The Western Wind and Solar Integration Study (WWSIS), sponsored by the U.S. Department of Energy, is one of the largest regional solar and wind integration studies to date. In multiple phases, it has explored different aspects of the question: Can we integrate large amounts of wind and solar energy into the electric power system of the West? The work reported here focused on the impact of low levels of synchronous generation on the transient stability performance in one part of the region in which wind generation has displaced synchronous thermal generation under highly stressed, weak system conditions. It is essentially an extension of WWSIS-3. Transient stability, the ability of the power system to maintain synchronism among all elements following disturbances, is a major constraint on operations in many grids, including the western U.S. and Texas systems. These constraints primarily concern the performance of the large-scale bulk power system. But grid-wide stability concerns with high penetrations of wind and solar are still not thoroughly understood. This work focuses on 'traditional' fundamental frequency stability issues, such as maintaining synchronism, frequency, and voltage. The objectives of this study are to better understand the implications of low levels of synchronous generation and a weak grid on overall system performance by: 1) Investigating the Western Interconnection under conditions of both high renewable

  17. On the integration of wind generators on weak grids and island grids; Sur l'integration des generateurs eoliens dans les reseaux faibles ou insulaires

    Energy Technology Data Exchange (ETDEWEB)

    Laverdure, N

    2005-12-15

    Wind energy is now an energy that can not be ignored. Because of intrinsic characteristics (scattered primary energy, generators with different technologies, use of power electronics interface), wind energy system integration in distribution grids leads to real problems in terms of impacts. With recent standard changes, it is necessary to study the possibilities of each technology of wind turbines to answer or not to these new constraints. This PhD thesis focuses on a comparison of the main present wind turbines concerning three points of discussion: energy quality, fault ride through, ancillary services (voltage and frequency). It insists on the possibilities in terms of control laws for variable speed wind turbines. (author)

  18. A Transmission-Cost-Based Model to Estimate the Amount of Market-Integrable Wind Resources

    DEFF Research Database (Denmark)

    Morales González, Juan Miguel; Pinson, Pierre; Madsen, Henrik

    2012-01-01

    are made to share the expenses in transmission derived from their integration, they may see the doors of electricity markets closed for not being competitive enough. This paper presents a model to decide the amount of wind resources that are economically exploitable at a given location from a transmission......-cost perspective. This model accounts for the uncertain character of wind by using a modeling framework based on stochastic optimization, simulates market barriers by means of a bi-level structure, and considers the financial risk of investments in transmission through the conditional value-at-risk. The major...

  19. Power-based control with integral action for wind turbines connected to the grid

    Science.gov (United States)

    Peña, R. R.; Fernández, R. D.; Mantz, R. J.; Battaiotto, P. E.

    2015-10-01

    In this paper, a power shaping control with integral action is employed to control active and reactive powers of wind turbines connected to the grid. As it is well known, power shaping allows finding a Lyapunov function which ensures stability. In contrast to other passivity-based control theories, the power shaping controller design allows to use easily measurable variables, such as voltages and currents which simplify the physical interpretation and, therefore, the controller synthesis. The strategy proposed is evaluated in the context of severe operating conditions, such as abrupt changes in the wind speed and voltage drops.

  20. Integrated resource planning - a long and winding road

    International Nuclear Information System (INIS)

    The separation of Croatia from former Yugoslavia and the military turbulence at its borders during the last years caused a number of problems in the Croatian energy system. Resources for improving the situation are scarce. So it is necessary to plan the rehabilitation and modernization of the Croatian energy system in a way which includes all national resources and allocates these resources where they lead to the highest benefits to the national economy. In this paper it is shown that Integrated Resource Planning (IRP) is such a method which enables the rational use of national resources. Also presented in this paper is a transparent and rational procedure which allows the energy planner to support the decision maker in developing an energy policy under consideration of interests of affected groups. This procedure is called Structured Analysis Procedure and step by step leads from the problem formulation to the decision on which action is to be applied to solve the problem. (author)

  1. Wind Energy Management System Integration Project Incorporating Wind Generation and Load Forecast Uncertainties into Power Grid Operations

    Energy Technology Data Exchange (ETDEWEB)

    Makarov, Yuri V.; Huang, Zhenyu; Etingov, Pavel V.; Ma, Jian; Guttromson, Ross T.; Subbarao, Krishnappa; Chakrabarti, Bhujanga B.

    2010-09-01

    features make this work a significant step forward toward the objective of incorporating of wind, solar, load, and other uncertainties into power system operations. In this report, a new methodology to predict the uncertainty ranges for the required balancing capacity, ramping capability and ramp duration is presented. Uncertainties created by system load forecast errors, wind and solar forecast errors, generation forced outages are taken into account. The uncertainty ranges are evaluated for different confidence levels of having the actual generation requirements within the corresponding limits. The methodology helps to identify system balancing reserve requirement based on a desired system performance levels, identify system “breaking points”, where the generation system becomes unable to follow the generation requirement curve with the user-specified probability level, and determine the time remaining to these potential events. The approach includes three stages: statistical and actual data acquisition, statistical analysis of retrospective information, and prediction of future grid balancing requirements for specified time horizons and confidence intervals. Assessment of the capacity and ramping requirements is performed using a specially developed probabilistic algorithm based on a histogram analysis incorporating all sources of uncertainty and parameters of a continuous (wind forecast and load forecast errors) and discrete (forced generator outages and failures to start up) nature. Preliminary simulations using California Independent System Operator (California ISO) real life data have shown the effectiveness of the proposed approach. A tool developed based on the new methodology described in this report will be integrated with the California ISO systems. Contractual work is currently in place to integrate the tool with the AREVA EMS system.

  2. Dynamic Biogas Upgrading for Integration of Renewable Energy from Wind, Biomass and Solar

    DEFF Research Database (Denmark)

    Jurgensen, Lars

    The Sabatier process is investigated as a storage scheme for renewable energy. Hydrogen derived from fluctuating renewable energy sources like wind and solar is converted to methane by the hydrogenation/methanation of carbon oxides. Biogas from anaerobic digestion is considered in this study...... as a high concentrated source of carbon dioxide. By using the Sabatier process, the CO2 content of the biogas is converted to CH4, which is a new upgrading process for biogas. By switching between (i) this upgrading process during periods of extensive electricity production from wind and solar, and (ii......) combined heat and power production from biogas during periods of electricity demand, bioenergy utilization becomes a dynamic process. In such a process scheme, biomass, wind, and solar could be integrated in a local context. This thesis aims to demonstrate the feasibility of the dynamic biogas upgrading...

  3. Electricity cost effects of expanding wind power and integrating energy sectors

    Directory of Open Access Journals (Sweden)

    Victor Maxwell

    2015-06-01

    Full Text Available Recently, questions have arisen in Denmark as to how and why public funding should be allocated to wind power producers. This is, among other reasons, due to pressure from industrial electricity consumers who want their overall energy costs lowered. Utilising existing wind power subsidies across energy sectors may be an effective means of dealing with these concerns. The following article takes the case of a community owned renewable energy project as a microcosm for the entire Danish energy system. The local project seeks to integrate energy sectors so as to create physical and financial conditions which could allow wind power producers to reduce their reliance on subsidies. It is found that the strategy may be effective in lowering the overall energy costs of electricity consumers. Further, it is found possible to scale up this strategy and realise benefits on a national scale.

  4. Power system integration of VSC-HVDC connected offshore wind power plants

    DEFF Research Database (Denmark)

    Zeni, Lorenzo; Kjær, Philip Carne

    introduction to justify the study, describe the state-of-art and formulate the project’s objectives, the report is essentially divided into three parts, as follows. Control principles of offshore AC networks The control of offshore AC networks relies purely on power electronics, especially if Type 4 wind......This report presents an overview of challenges and solutions for the integration into the power system of offshore wind power plants (WPPs) connected to onshore grids through a voltage-source converter based high voltage direct current (VSC-HVDC) transmission system. Aspects that are touched upon...... of the network in the vicinity of the HVDC station and (iii) limiting characteristics of WPPs such as inherent control and communication delays, presence of mechanical resonances at the same frequency as POD and active power ramp-rate limitations. Clustering of wind power plants The proof of concept...

  5. Review of DC System Technologies for Large Scale Integration of Wind Energy Systems with Electricity Grids

    Directory of Open Access Journals (Sweden)

    Sheng Jie Shao

    2010-06-01

    Full Text Available The ever increasing development and availability of power electronic systems is the underpinning technology that enables large scale integration of wind generation plants with the electricity grid. As the size and power capacity of the wind turbine continues to increase, so is the need to place these significantly large structures at off-shore locations. DC grids and associated power transmission technologies provide opportunities for cost reduction and electricity grid impact minimization as the bulk power is concentrated at single point of entry. As a result, planning, optimization and impact can be studied and carefully controlled minimizing the risk of the investment as well as power system stability issues. This paper discusses the key technologies associated with DC grids for offshore wind farm applications.

  6. PATH INTEGRAL SOLUTION OF NONLINEAR DYNAMIC BEHAVIOR OF STRUCTURE UNDER WIND EXCITATION

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    A numerical scheme for the nonlinear behavior of structure under wind excitation is investigated. With the white noise filter of turbulent-wind fluctuations, the nonlinear motion equation of structures subjected to wind load was modeled as the Ito' s stochastic differential equation. The state vector associated with such a model is a diffusion process. A continuous linearization strategy in the time-domain was adopted.Based on the solution series of its stochastic linearization equations, the formal probabilistic density of the structure response was developed by the path integral technique. It is shown by the numerical example of a guyed mast that compared with the frequency-domain method and the time-domain nonlinear analysis, the proposed approach is highlighted by high accuracy and effectiveness. The influence of the structure non-linearity on the dynamic reliability assessment is also analyzed in the example.

  7. Wind power integration using individual heat pumps – Analysis of different heat storage options

    DEFF Research Database (Denmark)

    Hedegaard, Karsten; Mathiesen, Brian Vad; Lund, Henrik;

    2012-01-01

    Significant installations of individual heat pumps are expected in future energy systems due to their economic competitiveness. This case study of the Danish energy system in 2020 with 50% wind power shows that individual heat pumps and heat storages can contribute to the integration of wind power....... Heat accumulation tanks and passive heat storage in the construction are investigated as two alternative storage options in terms of their ability to increase wind power utilisation and to provide cost-effective fuel savings. Results show that passive heat storage can enable equivalent to larger...... reductions in excess electricity production and fuel consumption than heat accumulation tanks. Moreover, passive heat storage is found to be significantly more cost-effective than heat accumulation tanks. In terms of reducing fuel consumption of the energy system, the installation of heat pumps is the most...

  8. Influence of individual heat pumps on wind power integration – Energy system investments and operation

    DEFF Research Database (Denmark)

    Hedegaard, Karsten; Münster, Marie

    2013-01-01

    Individual heat pumps are expected to constitute a significant electricity demand in future energy systems. This demand becomes flexible if investing in complementing heat storage capabilities. In this study, we analyse how the heat pumps can influence the integration of wind power by applying...... an energy system model that optimises both investments and operation, and covers various heat storage options. The Danish energy system by 2030 with around 50–60% wind power is used as a case study. Results show that the heat pumps, even without flexible operation, can contribute significantly...... to facilitating larger wind power investments and reducing system costs, fuel consumption, and CO2 emissions. Investments in heat storages can provide only moderate system benefits in these respects. The main benefit of the flexible heat pump operation is a reduced need for peak/reserve capacity, which is also...

  9. Electricity cost effects of expanding wind power and integrating energy sectors

    DEFF Research Database (Denmark)

    Rodriguez, Victor Adrian Maxwell; Sperling, Karl; Hvelplund, Frede Kloster

    2015-01-01

    Recently, questions have arisen in Denmark as to how and why public funding should be allocated to wind power producers. This is, among other reasons, due to pressure from industrial electricity consumers who want their overall energy costs lowered. Utilising existing wind power subsidies across...... energy sectors may be an effective means of dealing with these concerns. The following article takes the case of a community owned renewable energy project as a microcosm for the entire Danish energy system. The local project seeks to integrate energy sectors so as to create physical and financial...... conditions which could allow wind power producers to reduce their reliance on subsidies. It is found that the strategy may be effective in lowering the overall energy costs of electricity consumers. Further, it is found possible to scale up this strategy and realise benefits on a national scale....

  10. A planar and tunable bandpass filter on a ferrite substrate with integrated windings

    KAUST Repository

    Arabi, Eyad

    2015-05-01

    Tunable Filters that are based on ferrite materials are often biased by external magnets or coils which are large and bulky. In this work a completely planar, CPW-based bandpass filter is presented with integrated windings. Due to these windings the size of the filter is only 26mm × 34mm × 0.38mm which is orders of magnitude smaller than the traditional designs with external windings. The filter is realized by electroplating of Copper over seed layers of Titanium and Gold over a YIG substrate. The fabricated filter achieves a tunability of 3.4% without any external magnets or coils. A good insertion loss of 2.3 dBs and rejection greater than 50 dBs have been obtained. To the best of the authors knowledge, this design is the first ferrite-based design that is completely planar and self-biased.

  11. Influence of individual heat pumps on wind power integration – Energy system investments and operation

    International Nuclear Information System (INIS)

    Highlights: • Individual heat pumps can significantly support the integration of wind power. • The heat pumps significantly reduce fuel consumption, CO2 emissions, and costs. • Heat storages for the heat pumps can provide only moderate system benefits. • Main benefit of flexible heat pump operation is a lower peak/reserve capacity need. • Socio-economic feasibility only identified for some heat storages to some extent. - Abstract: Individual heat pumps are expected to constitute a significant electricity demand in future energy systems. This demand becomes flexible if investing in complementing heat storage capabilities. In this study, we analyse how the heat pumps can influence the integration of wind power by applying an energy system model that optimises both investments and operation, and covers various heat storage options. The Danish energy system by 2030 with around 50–60% wind power is used as a case study. Results show that the heat pumps, even without flexible operation, can contribute significantly to facilitating larger wind power investments and reducing system costs, fuel consumption, and CO2 emissions. Investments in heat storages can provide only moderate system benefits in these respects. The main benefit of the flexible heat pump operation is a reduced need for peak/reserve capacity, which is also crucial for the feasibility of the heat storages. Socio-economic feasibility is identified for control equipment enabling intelligent heat storage in the building structure and in existing hot water tanks. In contrast, investments in new heat accumulation tanks are not found competitive

  12. Challenge of Primary Voltage Control in Large Scale Wind Integrated Power System: A Danish Power System Case Study

    DEFF Research Database (Denmark)

    Rather, Zakir Hussain; Chen, Zhe; Thøgersen, Paul

    2013-01-01

    Grid integration of Renewable Energy (RE) at large scale poses vast majority of challenges to secure and stable operation of Power System. This paper presents the challenge of short circuit power and primary voltage control of wind integrated power system where majority of conventional generators...... are replaced by wind generators. The impact of large scale wind integration on fast reactive power support is studied in this paper. Considering both technical and economic aspects, alternatives to address the challenge of dynamic voltage support have also been demonstrated in this paper. A case study...

  13. ARRA-Multi-Level Energy Storage and Controls for Large-Scale Wind Energy Integration

    Energy Technology Data Exchange (ETDEWEB)

    David Wenzhong Gao

    2012-09-30

    The Project Objective is to design innovative energy storage architecture and associated controls for high wind penetration to increase reliability and market acceptance of wind power. The project goals are to facilitate wind energy integration at different levels by design and control of suitable energy storage systems. The three levels of wind power system are: Balancing Control Center level, Wind Power Plant level, and Wind Power Generator level. Our scopes are to smooth the wind power fluctuation and also ensure adequate battery life. In the new hybrid energy storage system (HESS) design for wind power generation application, the boundary levels of the state of charge of the battery and that of the supercapacitor are used in the control strategy. In the controller, some logic gates are also used to control the operating time durations of the battery. The sizing method is based on the average fluctuation of wind profiles of a specific wind station. The calculated battery size is dependent on the size of the supercapacitor, state of charge of the supercapacitor and battery wear. To accommodate the wind power fluctuation, a hybrid energy storage system (HESS) consisting of battery energy system (BESS) and super-capacitor is adopted in this project. A probability-based power capacity specification approach for the BESS and super-capacitors is proposed. Through this method the capacities of BESS and super-capacitor are properly designed to combine the characteristics of high energy density of BESS and the characteristics of high power density of super-capacitor. It turns out that the super-capacitor within HESS deals with the high power fluctuations, which contributes to the extension of BESS lifetime, and the super-capacitor can handle the peaks in wind power fluctuations without the severe penalty of round trip losses associated with a BESS. The proposed approach has been verified based on the real wind data from an existing wind power plant in Iowa. An

  14. Limits in the integration of Wind Farms in the Spanish wholesale electrical market

    Energy Technology Data Exchange (ETDEWEB)

    Rivier Abbad, J.; Mendez Quezada, V.H.; Gomez San Roman, T. [Universidad Pontificia Comillas of Madrid, Madrid (Spain)

    2006-07-01

    Sustainability and security of supply of our energy system is becoming one of the major issues under discussion in the past few years. Renewable energy sources (RES) play a significant role in both achieving a sustainable energy system and reducing the dependency on energy imports. Unfortunately, the current regulatory and economic framework does not allow renewable technologies to be competitive. To overcome this situation, several supporting mechanisms have been put in place in order to allow them to develop. The most important one or, at least the one that has allowed a higher deployment of renewable generation facilities, especially wind, is the Feed-in-Tariff (FIT) scheme. However, it has some drawbacks, one of them being that it hardly gives any incentives to renewable energy sources to really integrate into the existing power system, leading therefore to inefficient behavior. Recently, Spain has redesigned his supporting mechanism to better integrate Wind Parks into the existing system: there is now the possibility of accessing the market almost as a standard generator to sell its production, and having a fixed top up income (a premium) for each kWh. This paper will analyze pros and cons of this scheme. Especially emphasis will be given to what are the economical signals received by any wind farm with this mechanism, and what is their expected modified behavior. The paper will conclude that, although the new regulation is a very important step towards a better integration of the wind generators into the existing system, there are still several problems that prevent a real integration.

  15. Modelling the potential for wind energy integration on China’s coal-heavy electricity grid

    Science.gov (United States)

    Davidson, Michael R.; Zhang, Da; Xiong, Weiming; Zhang, Xiliang; Karplus, Valerie J.

    2016-07-01

    Expanding the use of wind energy for electricity generation forms an integral part of China’s efforts to address degraded air quality and climate change. However, the integration of wind energy into China’s coal-heavy electricity system presents significant challenges owing to wind’s variability and the grid’s system-wide inflexibilities. Here we develop a model to predict how much wind energy can be generated and integrated into China’s electricity mix, and estimate a potential production of 2.6 petawatt-hours (PWh) per year in 2030. Although this represents 26% of total projected electricity demand, it is only 10% of the total estimated physical potential of wind resources in the country. Increasing the operational flexibility of China’s coal fleet would allow wind to deliver nearly three-quarters of China’s target of producing 20% of primary energy from non-fossil sources by 2030.

  16. An Integrating VAP Method for Single-Doppler Radar Wind Retrieval

    Institute of Scientific and Technical Information of China (English)

    LIANG Xudong; WANG Bin

    2009-01-01

    Some traditional methods, such as the velocity-azimuth display (VAD) and the velocity-azimuth pro-cessing (VAP), have been widely used to retrieve the 3-D wind field from single-Doppler radar data because of their relative conceptual and practical simplicity. The advantage of VAD is that it is not affected by small-scale perturbations of the radial wind along the azimuth, to which the VAP method is very sensitive. Nevertheless, the spatial resolution of the VAD method is very poor compared to the VAP method. We show, in this study, that these two retrieval methods are actually related with each other and they are two special applications of a retrieval function based on the azimuthal uniform-wind assumption for a given azimuthal interval [θ1,θ2]. When using this retrieval function to retrieve wind fields, the azimuthal interval used in retrieval can be adjusted according to the requirement of smoothness or resolution. The larger (smaller) the azimuthal interval is, the coarser (finer) the horizontal resolution of retrieved wind field is, and the more insensitive (sensitive) the retrieval method is to small-scale perturbations. Because the full information within the azimuthal interval [θ1,θ2], instead of the information at two terminal points only, i.e., azimuths θ1 and θ2, is used to retrieve the wind fields, this method is referred to as the integrating VAP (IVAP) method, wherein the horizontal wind field is retrieved by using the Doppler velocity over the part of circumference, delimited by the given azimuthal interval times the scan radius. By contrast, the VAP method uses only the velocities at two terminal points of the given azimuthal interval. Therefore, the IVAP method has a filtering function, and the filtering rate can be controlled by adjusting the azimuthal interval. The filter such as that used in the pre-processing of the VAP method is no longer necessary for the IVAP method. When the retrieval azimuthal interval is as large as a whole

  17. Integrating wind power in EU electricity systems. Economic and technical issues

    International Nuclear Information System (INIS)

    In view of the ongoing process of liberalisation of the electricity market and the expected increase of wind power pursuant the RES-E Directive (Renewable Energy Sources - Electricity) and the need to minimise the costs of the RES-E targets, this study discusses the technical and economic impacts of integrating wind power into the electricity system. Furthermore, two options for reducing costs of intermittency are researched: forecasting of wind power output and electricity storage. An increasing penetration of wind power into the electricity system causes additional costs, partly due to the fact that the energy source of wind power is uncontrollable, variable (on the short term as well as on the longer term), and unpredictable (especially on the longer term). Consequently, balancing generation and demand becomes more complicated, creating a need for additional secondary and tertiary control. Although the sources of increasing costs are becoming more clearly understood, as are means to mitigate them, the quantification of costs of operating an electricity system with high wind penetration is very hard. Two possible options to reduce costs of intermittency are discussed in this report: forecasting of wind power output and electricity storage. The need for and benefit of wind energy forecasting have been increasingly recognised in recent years. Forecasting of wind power directs on increasing the predictability of the resource and improved forecasting can help to enhance the balancing of supply and demand. DG (distributed generation) operators can provide better information about their expected power output, energy suppliers can submit better estimates of electricity production to the TSO (Transmission System Operator), and system operators can improve network management through better information about expected power flows. Electricity storage systems can, at the same time, offer different services to a number of actors. Next to benefits that result from price

  18. Conference 'What strategies for an effective grid integration of wind energy? France-Germany crossed views'

    International Nuclear Information System (INIS)

    The French-German office for Renewable energies (OFAEnR) organised a conference on the effective grid integration of wind energy. In the framework of this French-German exchange of experience, more than a hundred participants exchanged views on the necessary stabilization and development of power grids for the integration of renewable energy sources. Beside the recent evolutions of regulations in both countries, topics such as the connection of offshore parks, the transient capacity hosting, the wind facilities efficiency and the grid development studies were addressed as well. This document brings together the available presentations (slides) made during this event: 1 - Grids development from the point of view of the Federal Ministry of environment - The German law on energy networks development 'Energieleitungsausbaugesetz'. High-voltage grid development in Germany: the impetus of the grid reinforcement law (Udo Paschedag); 2 - Danish experience and plans relating to wind energy integration and underground cables (Torsten Lund); 3 - Development of the French grid: Regional scheme of renewable energies connection (Louis Sanchez); 4 - Wind energy, a major component of the electricity mix for 2020/2030 (Jean-Yves Grandidier); 5 - Challenges of offshore wind parks connection to the German grids (Tim Meyerjuergens); 6 - Connection potentialities: transient production hosting capacities (Severine Laurent); 7 - Wind power plants supply system services - Requirements imposed to grid operators and economic incentives: a wind energy with the same quality as conventional electricity? (Jean Lacoste); 8 - Grid reinforcements and what they are to wind - A European perspective (Alex De Broe); 9 - European Wind Integration Study (EWIIS) - Towards a Successful Integration of Wind Power into European electricity Grids. The EWIS study and expectations about offshore grid development in the North/Baltic Sea area (Lothar Fischer); 10 - Optimization of renewable energies

  19. Benefit of regional energy balancing service on wind integration in the western interconnection of the United States

    Energy Technology Data Exchange (ETDEWEB)

    Milligan, Michael; Kirby, Brendan; King, Jack [National Renewable Energy Laboratory, Golden, CO (United States); Beuning, Stephen [Xcel Energy Inc., Minneapolis, MN (United States)

    2010-07-01

    Interest in various wide-area balancing schemes to help integrate wind have generated significant interest. As we have shown in past work, large balancing areas not only help with wind integration, but can also increase the efficiency of operations in systems without wind. Recent work on the Western Wind and Solar Integration Study (WWSIS) has found that combining balancing over the WestConnect footprint will increase the efficiency of commitment and dispatch at wind penetrations ranging from 10-30% of annual electricity demand, and will be essential for high penetrations and small balancing areas. In addition the northwest Wind Integration Action Plan recommended balancing area cooperation as a method to help integrate the large potential wind development. In this paper we investigate the potential impact of a proposed Energy Imbalance Service on the ability of the non-market portions of Western Electricity Coordinating Councils (WECC) United States footprint to integrate wind energy. We will utilize data adapted from the WWSIS for the Western Interconnection. The analysis uses time-synchronized wind and load data to evaluate the potential for ramp requirement reduction that could be achieved with combined operation. Chronological analysis and ramp duration analysis quantify the benefit in terms of not only the ramp sizes, but the frequency of the potentially avoided ramps that must be managed by the non-wind generation fleet. Multiple approaches that can be used to achieve these benefits are also suggested in the paper. We also suggest other approaches that can help achieve much of the benefit of full consolidation without requiring the physical consolidation of balancing areas. (orig.)

  20. Integration of plug-in hybrid electric vehicles in a regional wind-thermal power system

    International Nuclear Information System (INIS)

    This study investigates consequences of integrating plug-in hybrid electric vehicles (PHEVs) in a wind-thermal power system supplied by one quarter of wind power and three quarters of thermal generation. Four different PHEV integration strategies, with different impacts on the total electric load profile, have been investigated. The study shows that PHEVs can reduce the CO2-emissions from the power system if actively integrated, whereas a passive approach to PHEV integration (i.e. letting people charge the car at will) is likely to result in an increase in emissions compared to a power system without PHEV load. The reduction in emissions under active PHEV integration strategies is due to a reduction in emissions related to thermal plant start-ups and part load operation. Emissions of the power sector are reduced with up to 4.7% compared to a system without PHEVs, according to the simulations. Allocating this emission reduction to the PHEV electricity consumption only, and assuming that the vehicles in electric mode is about 3 times as energy efficient as standard gasoline operation, total emissions from PHEVs would be less than half the emissions of a standard car, when running in electric mode.

  1. Optimal Siting and Sizing of Energy Storage System for Power Systems with Large-scale Wind Power Integration

    DEFF Research Database (Denmark)

    Zhao, Haoran; Wu, Qiuwei; Huang, Shaojun;

    2015-01-01

    This paper proposes algorithms for optimal sitingand sizing of Energy Storage System (ESS) for the operationplanning of power systems with large scale wind power integration.The ESS in this study aims to mitigate the wind powerfluctuations during the interval between two rolling Economic...

  2. Western Wind and Solar Integration Study Phase 3 -- Frequency Response and Transient Stability (Report and Executive Summary)

    Energy Technology Data Exchange (ETDEWEB)

    Miller, N. W.; Shao, M.; Pajic, S.; D' Aquila, R.

    2014-12-01

    The primary objectives of Phase 3 of the Western Wind and Solar Integration Study (WWSIS-3) were to examine the large-scale transient stability and frequency response of the Western Interconnection with high wind and solar penetration, and to identify means to mitigate any adverse performance impacts via transmission reinforcements, storage, advanced control capabilities, or other alternatives.

  3. Equivalent Method of Integrated Power Generation System of Wind, Photovoltaic and Energy Storage in Power Flow Calculation and Transient Simulation

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    The integrated power generation system of wind, photovoltaic (PV) and energy storage is composed of several wind turbines, PV units and energy storage units. The detailed model of integrated generation is not suitable for the large-scale powe.r system simulation because of the model's complexity and long computation time. An equivalent method for power flow calculation and transient simulation of the integrated generation system is proposed based on actual projects, so as to establish the foundation of such integrated system simulation and analysis.

  4. Strategic integration of new technologies for a wind-power system adapted to remote areas : concept review

    Energy Technology Data Exchange (ETDEWEB)

    Lautier, P. [Envitech Automation Inc., Pointe Claire, PQ (Canada); Dery, J. [Dermond Inc., Ada, MI (United States); Houasnia, A. [Quebec Univ., Trois-Rivieres, PQ (Canada). Groupe de Recherche en Electronique Industrielle

    2005-07-01

    This paper presented a new renewable energy system (RES) based on wind energy associated with auxiliary power sources. The system is based on the variable speed vertical axis wind turbine and can integrate various types of power equipment, including batteries, diesel generators and dump loads. A 100 kW wind turbine prototype was installed in October 2004 in Rouyn-Noranda and a 200 kW wind turbine is under development and commercialization. The systems should be commissioned in 2006. This paper reviewed the power structure and advanced control strategies of the entire RES. Each element of the power generation system were described along with details of the control techniques developed to comply with grid-connected and off-grid requirements. The power system integrator and system control architecture were also presented. It was shown that power quality can be greatly improved through adequate control of the wind turbine and battery bank. 14 refs., 12 figs.

  5. Techniques for a Wind Energy System Integration with an Islanded Microgrid

    Science.gov (United States)

    Goyal, Megha; Fan, Yuanyuan; Ghosh, Arindam; Shahnia, Farhad

    2016-04-01

    This paper presents two different techniques of a wind energy conversion system (WECS) integration with an islanded microgrid (MG). The islanded microgrid operates in a frequency droop control where its frequency can vary around 50 Hz. The permanent magnet synchronous generator (PMSG) based variable speed WECS is considered, which converts wind energy to a low frequency ac power. Therefore it needs to be connected to the microgrid through a back to back (B2B) converter system. One way of interconnection is to synchronize the MG side converter with the MG bus at which it is connected. In this case, this converter runs at the MG frequency. The other approach is to bring back the MG frequency to 50 Hz using the isochronization concept. In this case, the MG side converter operates at 50 Hz. Both these techniques are developed in this paper. The proposed techniques are validated through extensive PSCAD/EMTDC simulation studies.

  6. Integration of electric drive vehicles in the Danish electricity network with high wind power penetration

    DEFF Research Database (Denmark)

    Chandrashekhara, Divya K; Østergaard, Jacob; Larsen, Esben;

    2010-01-01

    /conventional) which are likely to fuel these cars. The study was carried out considering the Danish electricity network state around 2025, when the EDV penetration levels would be significant enough to have an impact on the power system. Some of the interesting findings of this study are - EDV have the potential......This paper presents the results of a study carried out to examine the feasibility of integrating electric drive vehicles (EDV) in the Danish electricity network which is characterised by high wind power penetration. One of the main aims of this study was to examine the effect of electric drive...... vehicles on the Danish electricity network, wind power penetration and electricity market. In particular the study examined the effect of electric drive vehicles on the generation capacity constraints, load curve, cross border transmission capacity and the type of generating sources (renewable...

  7. Large-scale offshore wind energy. Cost analysis and integration in the Dutch electricity market

    International Nuclear Information System (INIS)

    The results of analysis of the construction and integration costs of large-scale offshore wind energy (OWE) farms in 2010 are presented. The integration of these farms (1 and 5 GW) in the Dutch electricity distribution system have been regarded against the background of a liberalised electricity market. A first step is taken for the determination of costs involved in solving integration problems. Three different types of foundations are examined: the mono-pile, the jacket and a new type of foundation: the concrete caisson pile: all single-turbine-single-support structures. For real offshore applications (>10 km offshore, at sea-depths >20 m), the concrete caisson pile is regarded as the most suitable. The price/power ratios of wind turbines are analysed. It is assumed that in 2010 turbines in the power range of 3-5 MW are available. The main calculations have been conducted for a 3 MW turbine. The main choice in electrical infrastructure is for AC or DC. Calculations show that at distances of 30 km offshore and more, the use of HVDC will result in higher initial costs but lower operating costs. The share of operating and maintenance (O ampersand M) costs in the kWh cost price is approximately 3.3%. To be able to compare the two farms, a base case is derived with a construction time of 10 years for both. The energy yield is calculated for a wind regime offshore of 9.0 m/s annual mean wind speed. Per 3 MW turbine this results in an annual energy production of approximately 12 GWh. The total farm efficiency amounts to 82%, resulting in a total farm capacity factor of 38%. With a required internal rate of return of 15%, the kWh cost price amounts to 0.24 DFl and 0.21 DFl for the 1 GW and 5 GW farms respectively in the base case. The required internal rate of return has a large effect on the kWh cost price, followed by costs of subsystems. O ampersand M costs have little effect on the cost price. Parameter studies show that a small cost reduction of 5% is possible when

  8. More Wind Power Integration with Adjusted Energy Carriers for Space Heating in Northern China

    Directory of Open Access Journals (Sweden)

    Jianjun He

    2012-08-01

    Full Text Available In Northern China, due to the high penetration of coal-fired cogeneration facilities, which are generally equipped with extraction-condensing steam turbines, lots of wind power resources may be wasted during the heating season. In contrast, considerable coal is consumed in the power generation sector. In this article, firstly it is revealed that there exists a serious divergence in the ratio of electrical to thermal energy between end users’ demand and the cogenerations’ production during off-peak load at night, which may negate active power-balancing of the electric power grid. Secondly, with respect to this divergence only occurring during off-peak load at night, a temporary proposal is given so as to enable the integration of more wind power. The authors suggest that if the energy carrier for part of the end users’ space heating is switched from heating water to electricity (e.g., electric heat pumps (EHPs can provide space heating in the domestic sector, the ratio of electricity to heating water load should be adjusted to optimize the power dispatch between cogeneration units and wind turbines, resulting in fuel conservation. With this proposal, existing infrastructures are made full use of, and no additional ones are required. Finally a numerical simulation is performed in order to illustrate both the technical and economic feasibility of the aforementioned proposal, under ongoing infrastructures as well as electricity and space heating tariff conditions without changing participants’ benefits. The authors aim to persuade Chinese policy makers to enable EHPs to provide space heating to enable the integration of more wind power.

  9. 2010 Pacific Gas and Electric Diablo Canyon Power Plant (DCPP): Diablo Canyon, CA Central Coast

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Diablo Canyon Power Plant (DCPP) LiDAR and Imagery datasets are comprised of three separate LiDAR surveys: Diablo Canyon (2010), Diablo Canyon (2010), and San...

  10. Do urban canyons influence street level grass pollen concentrations?

    DEFF Research Database (Denmark)

    Peel, Robert George; Kennedy, Roy; Smith, Matt;

    2014-01-01

    to be statistically significant only in London. The ratio of street/roof level concentrations was compared with temperature, relative humidity, wind speed and direction, and solar radiation. Results indicated that the concentration ratio responds to wind direction with respect to relative canyon orientation and local......In epidemiological studies, outdoor exposure to pollen is typically estimated using rooftop monitoring station data, whilst exposure overwhelmingly occurs at street level. In this study the relationship between street level and roof level grass pollen concentrations was investigated for city centre...... street canyon environments in Aarhus, Denmark, and London, UK, during the grass pollen seasons of 2010 and 2011 respectively. For the period mid-day to late evening, street level concentrations in both cities tended to be lower than roof-level concentrations, though this difference was found...

  11. A New Building-Integrated Wind Turbine System Utilizing the Building

    Directory of Open Access Journals (Sweden)

    Jeongsu Park

    2015-10-01

    Full Text Available This paper proposes an innovative building-integrated wind turbine (BIWT system by directly utilizing the building skin, which is an unused and unavailable area in all conventional BIWT systems. The proposed system has been developed by combining a guide vane that is able to effectively collect the incoming wind and increase its speed and a rotor with an appropriate shape for specific conditions. To this end, several important design issues for the guide vane as well as the rotor were thoroughly investigated and accordingly addressed in this paper. A series of computational fluid dynamics (CFD analyses was performed to determine the optimal configuration of the proposed system. Finally, it is demonstrated from performance evaluation tests that the prototype with the specially designed guide vane and rotor for the proposed BIWT system accelerates the wind speed to a sufficient level and consequently increases the power coefficient significantly. Thus, it was confirmed that the proposed system is a promising environment-friendly energy production system for urban areas.

  12. Improved Adaptive Droop Control Design for Optimal Power Sharing in VSC-MTDC Integrating Wind Farms

    Directory of Open Access Journals (Sweden)

    Xiaohong Ran

    2015-07-01

    Full Text Available With the advance of insulated gate bipolar transistor (IGBT converters, Multi-Terminal DC (MTDC based on the voltage-source converter (VSC has developed rapidly in renewable and electric power systems. To reduce the copper loss of large capacity and long distance DC transmission line, an improved droop control design based on optimal power sharing in VSC-MTDC integrating offshore wind farm is proposed. The proposed approach provided a calculation method for power-voltage droop coefficients under two different scenarios either considering local load or not. The available headroom of each converter station was considered as a converter outage, to participate in the power adjustment according to their ability. A four-terminal MTDC model system including two large scale wind farms was set up in PSCAD/EMTDC. Then, the proposed control strategy was verified through simulation under the various conditions, including wind speed variation, rectifier outage and inverter outage, and a three-phase short-circuit of the converter.

  13. Review of relevant studies of isolated systems[Integration of wind energy

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, L.H.; Lundsager, P.

    2000-12-01

    The report presents the results of a review of studies relating to integration of wind energy in isolated power supply systems, based on a systematic literature survey. The purpose of the study is to develop a methodology consisting of a set of guidelines for wind energy projects in isolated energy systems and a set of tools and models that are operational on an engineering level. The review is based on a literature search in the ETDE Energy Database with a main search covering the period 7/88 to 6/97 and supplemented by partial update periods. A few newer references have been included in the review, most notably the IEC/PAS 62111 specification. The amount of wind energy literature related to the subject is excessively large, and a complete review in which every relevant abstract is identified and examined is not feasible within the framework of this (or probably any other) study. The review results have been organised according to the following keywords: methods & guides, economics, concept of application, system solutions, case studies, financial programmes, dedicated software tools. None of the found references presents methods or tools that contradict the philosophy of Risoe's methodology as it is described in the report. It is therefore concluded that Risoe's methodology makes a good platform for further development. (au)

  14. Integration of wind power plants into the electric system. The Brazilian experience

    Energy Technology Data Exchange (ETDEWEB)

    Arteiro, Francisco; Gomes, Paulo [Operador Nacional do Sistema Eletrico (ONS), Rio de Janeiro, RJ (Brazil)

    2012-07-01

    Traditionally, most generation plants are based on hydro or and thermal generating units. It is essential to recognize the critical role played by these unit generator controls in maintaining system adequate performance, its stability, and voltage and frequency control. In the last years, renewable generation integration has increased to supply new markets and in several countries mainly to displace thermal power plants, in order to face environmental societal pressure by energy ''more clean''. In many power systems, the amount of renewable generation connected to the grid system has been low so far. However, this scenario is all changing. Renewable generation, in particular wind power plants, is now becoming a major contributor to power systems and its contributions will increase even more in the next years. To give an idea of this, the European Wind Energy Associated estimated that in 2020 around 180 GW of wind power plants will be operational - 35 GW will be offshore. Some power systems predict that by 2020 up to 50% of installed capacity will be based on renewable generation. This considers both on-shore and off-shore generation. It is important to remark that in several countries this generation is used to displace traditional generation showing good performance, however due to environmental concerns the society does not tend to welcome this king of source. The impact of wind generation on power system performance should be assessed face to their effects considering time and space. Thus, short and long-term effects should be considered. The short term effects are caused by system balancing at the operational timescale (minutes to hours), whereas the long term effects are related to the contribution wind power can provide to reliably meet peak load and assure energetic security. Concerning the operation of renewable generation units together with traditional generation ones in terms of guaranteeing that such new generation units will not be

  15. Integrated Approach Using Condition Monitoring and Modeling to Investigate Wind Turbine Gearbox Design: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Sheng, S.; Guo, Y.

    2015-03-01

    Vibration-based condition monitoring (CM) of geared utility-scale turbine drivetrains has been used by the wind industry to help improve operation and maintenance (O&M) practices, increase turbine availability, and reduce O&M cost. This study is a new endeavor that integrates the vibration-based CM technique with wind turbine gearbox modeling to investigate various gearbox design options. A teamof researchers performed vibration-based CM measurements on a damaged wind turbine gearbox with a classic configuration, (i.e., one planetary stage and two parallel stages). We observed that the acceleration amplitudes around the first-order sidebands of the intermediate stage gear set meshing frequency were much lower than that measured at the high-speed gear set, and similar difference wasalso observed in a healthy gearbox. One factor for a reduction at the intermediate stage gear set is hypothesized to be the soft sun-spline configuration in the test gearbox. To evaluate this hypothesis, a multibody dynamic model of the healthy test gearbox was first developed and validated. Relative percent difference of the first-order sidebands--of the high-speed and intermediate stagegear-meshing frequencies--in the soft and the rigid sun spline configurations were compared. The results verified that the soft sun-spline configuration can reduce the sidebands of the intermediate stage gear set and also the locating bearing loads. The study demonstrates that combining vibration-based CM with appropriate modeling can provide insights for evaluating different wind turbinegearbox design options.

  16. ANEMOS: Development of a next generation wind power forecasting system for the large-scale integration of onshore and offshore wind farms.

    Science.gov (United States)

    Kariniotakis, G.; Anemos Team

    2003-04-01

    Objectives: Accurate forecasting of the wind energy production up to two days ahead is recognized as a major contribution for reliable large-scale wind power integration. Especially, in a liberalized electricity market, prediction tools enhance the position of wind energy compared to other forms of dispatchable generation. ANEMOS, is a new 3.5 years R&D project supported by the European Commission, that resembles research organizations and end-users with an important experience on the domain. The project aims to develop advanced forecasting models that will substantially outperform current methods. Emphasis is given to situations like complex terrain, extreme weather conditions, as well as to offshore prediction for which no specific tools currently exist. The prediction models will be implemented in a software platform and installed for online operation at onshore and offshore wind farms by the end-users participating in the project. Approach: The paper presents the methodology of the project. Initially, the prediction requirements are identified according to the profiles of the end-users. The project develops prediction models based on both a physical and an alternative statistical approach. Research on physical models gives emphasis to techniques for use in complex terrain and the development of prediction tools based on CFD techniques, advanced model output statistics or high-resolution meteorological information. Statistical models (i.e. based on artificial intelligence) are developed for downscaling, power curve representation, upscaling for prediction at regional or national level, etc. A benchmarking process is set-up to evaluate the performance of the developed models and to compare them with existing ones using a number of case studies. The synergy between statistical and physical approaches is examined to identify promising areas for further improvement of forecasting accuracy. Appropriate physical and statistical prediction models are also developed for

  17. Operation of Concentrating Solar Power Plants in the Western Wind and Solar Integration Phase 2 Study

    Energy Technology Data Exchange (ETDEWEB)

    Denholm, P.; Brinkman, G.; Lew, D.; Hummon, M.

    2014-05-01

    The Western Wind and Solar Integration Study (WWSIS) explores various aspects of the challenges and impacts of integrating large amounts of wind and solar energy into the electric power system of the West. The phase 2 study (WWSIS-2) is one of the first to include dispatchable concentrating solar power (CSP) with thermal energy storage (TES) in multiple scenarios of renewable penetration and mix. As a result, it provides unique insights into CSP plant operation, grid benefits, and how CSP operation and configuration may need to change under scenarios of increased renewable penetration. Examination of the WWSIS-2 results indicates that in all scenarios, CSP plants with TES provides firm system capacity, reducing the net demand and the need for conventional thermal capacity. The plants also reduced demand during periods of short-duration, high ramping requirements that often require use of lower efficiency peaking units. Changes in CSP operation are driven largely by the presence of other solar generation, particularly PV. Use of storage by the CSP plants increases in the higher solar scenarios, with operation of the plant often shifted to later in the day. CSP operation also becomes more variable, including more frequent starts. Finally, CSP output is often very low during the day in scenarios with significant PV, which helps decrease overall renewable curtailment (over-generation). However, the configuration studied is likely not optimal for High Solar Scenario implying further analysis of CSP plant configuration is needed to understand its role in enabling high renewable scenarios in the Western United States.

  18. Wind power integration with heat pumps, heat storages, and electric vehicles – Energy systems analysis and modelling

    DEFF Research Database (Denmark)

    Hedegaard, Karsten

    The fluctuating and only partly predictable nature of wind challenges an effective integration of large wind power penetrations. This PhD thesis investigates to which extent heat pumps, heat storages, and electric vehicles can support the integration of wind power. Considering the gaps in existing...... in an energy system context. Energy systems analyses reveal that the heat pumps can even without flexible operation contribute significantly to facilitating larger wind power investments and reducing system costs, fuel consumption, and CO2 emissions. When equipping the heat pumps with heat storages, only...... moderate additional benefits are achieved. Hereof, the main benefit is that the need for investing in peak/reserve capacities can be reduced through peak load shaving. It is more important to ensure flexible operation of electric vehicles than of individual heat pumps, due to differences in the load...

  19. Renewable energy integration into the Australian National Electricity Market: Characterising the energy value of wind and solar generation

    OpenAIRE

    Nicholas Boerema; Merlinde Kay; Iain MacGill

    2010-01-01

    This paper examines how key characteristics of the underlying wind and solar resources may impact on their energy value within the Australian National Electricity Market(NEM). Analysis has been performed for wind generation using half hour NEM data for South Australia over the 2008-9 financial year. The potential integration of large scale solar generation has been modelled using direct normal solar radiant energy measurements from the Bureau of Meteorology for six sites across the NEM. For w...

  20. A Laboratory Model for the Flow in Urban Street Canyons Induced by Bottom Heating

    Institute of Scientific and Technical Information of China (English)

    刘辉志; 梁彬; 朱凤荣; 张伯寅; 桑建国

    2003-01-01

    Water tank experiments are carried out to investigate the convection flow induced by bottom heating and the effects of the ambient wind on the flow in non-symmetrical urban street canyons based on the PIV (Particle Image Visualization) technique. Fluid experiments show that with calm ambient wind,the flows in the street canyon are completely driven by thermal force, and the convection can reach the upper atmosphere of the street canyon. Horizontal and vertical motions also appear above the roofs of the buildings. These are the conditions which favor the exchange of momentum and air mass between the street canyon and its environment. More than two vortices are induced by the convection, and the complex circulation pattern will vary with time in a wider street canyon. However, in a narrow street canyon, just one vortex appears. With a light ambient wind, the bottom heating and the associated convection result in just one main vortex. As the ambient wind speed increases, the vortex becomes more organized and its center shifts closer to the leeward building.

  1. Effects of large scale integration of wind and solar energy in Japan

    Science.gov (United States)

    Esteban, Miguel; Zhang, Qi; Utama, Agya; Tezuka, Tetsuo; Ishihara, Keiichi

    2010-05-01

    results for the country as a whole are considered it is still substantial. The results are greatly dependant on the mix between the proposed renewables (solar and wind), and by comparing different distributions and mixes, the optimum composition for the target country can be established. The methodology proposed is able to obtain the optimum mix of solar and wind power for a given system, provided that adequate storage capacity exists to allow for excess capacity to be used at times of low electricity production (at the comparatively rare times when there is neither enough sun nor wind throughout the country). This highlights the challenges of large-scale integration of renewable technologies into the electricity grid, and the necessity to combine such a system with other renewables such as hydro or ocean energy to further even out the peaks and lows in the demand.

  2. Pollen taphonomy in a canyon stream

    Science.gov (United States)

    Fall, Patricia L.

    1987-11-01

    Surface soil samples from the forested Chuska Mountains to the arid steppe of the Chinle Valley, Northeastern Arizona, show close correlation between modern pollen rain and vegetation. In contrast, modern alluvium is dominated by Pinus pollen throughout the canyon; it reflects neither the surrounding floodplain nor plateau vegetation. Pollen in surface soils is deposited by wind; pollen grains in alluvium are deposited by a stream as sedimentary particles. Clay-size particles correlate significantly with Pinus, Quercus, and Populus pollen. These pollen types settle, as clay does, in slack water. Chenopodiaceae- Amaranthus, Artemisia, other Tubuliflorae, and indeterminate pollen types correlate with sand-size particles, and are deposited by more turbulent water. Fluctuating pollen frequencies in alluvial deposits are related to sedimentology and do not reflect the local or regional vegetation where the sediments were deposited. Alluvial pollen is unreliable for reconstruction of paleoenvironments.

  3. Addressing System Integration Issues Required for the Developmente of Distributed Wind-Hydrogen Energy Systems: Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Mann, M.D; Salehfar, H.; Harrison, K.W.; Dale, N.; Biaku, C.; Peters, A.J.; Hernandez-Pacheco: E.

    2008-04-01

    Wind generated electricity is a variable resource. Hydrogen can be generated as an energy storage media, but is costly. Advancements in power electronics and system integration are needed to make a viable system. Therefore, the long-term goal of the efforts at the University of North Dakota is to merge wind energy, hydrogen production, and fuel cells to bring emission-free and reliable power to commercial viability. The primary goals include 1) expand system models as a tool to investigate integration and control issues, 2) examine long-term effects of wind-electrolysis performance from a systematic perspective, and 3) collaborate with NREL and industrial partners to design, integrate, and quantify system improvements by implementing a single power electronics package to interface wild AC to PEM stack DC requirements. This report summarizes the accomplishments made during this project.

  4. Direct power control of DFIG wind turbine systems based on an intelligent proportional-integral sliding mode control.

    Science.gov (United States)

    Li, Shanzhi; Wang, Haoping; Tian, Yang; Aitouch, Abdel; Klein, John

    2016-09-01

    This paper presents an intelligent proportional-integral sliding mode control (iPISMC) for direct power control of variable speed-constant frequency wind turbine system. This approach deals with optimal power production (in the maximum power point tracking sense) under several disturbance factors such as turbulent wind. This controller is made of two sub-components: (i) an intelligent proportional-integral module for online disturbance compensation and (ii) a sliding mode module for circumventing disturbance estimation errors. This iPISMC method has been tested on FAST/Simulink platform of a 5MW wind turbine system. The obtained results demonstrate that the proposed iPISMC method outperforms the classical PI and intelligent proportional-integral control (iPI) in terms of both active power and response time.

  5. Direct power control of DFIG wind turbine systems based on an intelligent proportional-integral sliding mode control.

    Science.gov (United States)

    Li, Shanzhi; Wang, Haoping; Tian, Yang; Aitouch, Abdel; Klein, John

    2016-09-01

    This paper presents an intelligent proportional-integral sliding mode control (iPISMC) for direct power control of variable speed-constant frequency wind turbine system. This approach deals with optimal power production (in the maximum power point tracking sense) under several disturbance factors such as turbulent wind. This controller is made of two sub-components: (i) an intelligent proportional-integral module for online disturbance compensation and (ii) a sliding mode module for circumventing disturbance estimation errors. This iPISMC method has been tested on FAST/Simulink platform of a 5MW wind turbine system. The obtained results demonstrate that the proposed iPISMC method outperforms the classical PI and intelligent proportional-integral control (iPI) in terms of both active power and response time. PMID:27346331

  6. Optimization of FACTS and battery systems for supporting wind integration; Einsatzoptimierung von FACTS und Batterieanlagen zur Unterstuetzung der Windintegration

    Energy Technology Data Exchange (ETDEWEB)

    Danesh Shakib, Arefeh

    2012-07-01

    In the future an increase of wind energy contribution for electricity generation in Germany is expected, especially regarding to the development of offshore wind farms. The fundamental difficulty lies in the optimum transfer of power for long distances using existing 380-kV voltage level. With the help of modern power electronics (FACTS) it is principally possible to influence the active power flow as well as the voltage stability. Another problem of using wind energy is the unpredictable character of the wind, which leads to a higher requirement of control power from the adjustable traditional power plants. Here, the application of modern high energy battery systems seems to be a meaningful possibility, in the case of the wind farms with a DC transmission concept. In this case, the existent voltage level can be used for the battery connection too. The present study considers the issues of the wind energy applications. The wind integration in the north and east regions requires a connection to the high voltage grid, but the number of available connection points in these regions is extremely low. The network topology of the German 380-kV grid will be simulated with the help of existing documents. For determining the optimal connection points of the planed offshore wind farms voltage stability analyses will be performed based on the simulated network. Thus, it is possible to compare the voltage behaviors of the available connection points with each other and to estimate the amount of the maximum active power injection, respectively. Furthermore, according to the network analysis with an additional wind injection, placement technologies of the FACTS devices will be developed and presented. Although the focus the studies is on static var compensators (SVC) and thyristor controlled compensators (TCSC), the methods can be used for other FACTS devices. To determine the optimum setting values of FACTS an optimal power flow problem will be formulated. Sensitivity analyses

  7. A new self-scheduling strategy for integrated operation of wind and pumped-storage power plants in power markets

    International Nuclear Information System (INIS)

    Highlights: → A strategy for integrated operation of wind and pumped-storage plants is proposed. → Participation of both plants in energy and ancillary service markets is modeled. → The uncertainty of wind production is modeled by a novel probabilistic function. → The proposed strategy is tested on a real case in the Spanish electricity market. -- Abstract: Competitive structure of power markets causes various challenges for wind resources to participate in these markets. Indeed, production uncertainty is the main cause of their low income. Thus, they are usually supported by system operators, which is in contrast with the competitive paradigm of power markets. In this paper, a new strategy for increasing the profits of wind resources is proposed. In the suggested strategy, a Generation Company (GenCo), who owns both wind and pumped-storage plants, self-schedules the integrated operation of them regarding the uncertainty of wind power generation. For presenting an integrated self-schedule and obtaining a real added value of the strategy, participation of the GenCo in energy and ancillary service markets is modeled. The self-scheduling strategy is based on stochastic programming techniques. Outputs of the problem include generation offers in day-ahead energy market and ancillary service markets, including spinning and regulation reserve markets. A Neural Network (NN) based technique is used for modeling the uncertainty of wind power production. The proposed strategy is tested on a real wind farm in mainland, Spain. Moreover, added value of the strategy is presented in different conditions of the market.

  8. Deepwater Canyons 2013: Pathways to the Abyss

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Leg I focused on biological objectives in Norfolk Canyon, with some sampling in Baltimore Canyon. Leg II focused on archaeological targets in and around the Norfolk...

  9. Unit Commitment Model Considering Flexible Scheduling of Demand Response for High Wind Integration

    Directory of Open Access Journals (Sweden)

    Beibei Wang

    2015-12-01

    Full Text Available In this paper, a two-stage stochastic unit commitment (UC model considering flexible scheduling of demand response (DR is proposed. In the proposed UC model, the DR resources can be scheduled: (1 in the first stage, as resources on a day-ahead basis to integrate the predicted wind fluctuation with lower uncertainty; (2 in the second stage, as resources on an intra-day basis to compensate for the deviation among multiple wind power scenarios considering the coupling relationship of DR on available time and capacity. Simulation results on the Pennsylvania-New Jersey-Maryland (PJM 5-bus system and IEEE 118-bus system indicate that the proposed model can maximize the DR value with lower cost. Moreover, different types of DR resources may vary in the contract costs (capacity costs, the responsive costs (energy costs, the time of advance notice, and the minimum on-site hours. The responsive cost is considered as the most important factor affecting DR scheduling. In addition, the first-stage DR is dispatched more frequently when transmission constraints congestion occurs.

  10. Droop Control Design of Multi-VSC Systems for Offshore Networks to Integrate Wind Energy

    Directory of Open Access Journals (Sweden)

    Muhammad Raza

    2016-10-01

    Full Text Available This research envisages the droop control design of multi voltage source converter systems for offshore networks to integrate wind power plant with the grids. An offshore AC network is formulated by connecting several nearby wind power plants together with AC cables. The net energy in the network is transferred to onshore using voltage source high voltage direct current (VSC-HVDC transmissionsystems. In the proposed configuration, an offshore network is energized by more than one VSC-HVDC system, hereby providing redundancy to continue operation in case of failure in one of the HVDC transmission lines. The power distribution between VSC-HVDC systems is done using a droop control scheme. Frequency droop is implemented to share active power, and voltage droop is implemented to share reactive power. Furthermore, a method of calculating droop gains according to the contribution factor of each converter is presented. The system has been analyzed to evaluate the voltage profile of the network affected by the droop control. Nonlinear dynamic simulation has been performed for the verification of the control principle.

  11. An Integrated Framework of Drivetrain Degradation Assessment and Fault Localization for Offshore Wind Turbines

    Directory of Open Access Journals (Sweden)

    Jay Lee

    2013-01-01

    Full Text Available As wind energy proliferates in onshore and offshore applications, it has become significantly important to predict wind turbine downtime and maintain operation uptime to ensure maximal yield. Two types of data systems have been widely adopted for monitoring turbine health condition: supervisory control and data acquisition (SCADA and condition monitoring system (CMS. Provided that research and development have focused on advancing analytical techniques based on these systems independently, an intelligent model that associates information from both systems is necessary and beneficial. In this paper, a systematic framework is designed to integrate CMS and SCADA data and assess drivetrain degradation over its lifecycle. Information reference and advanced feature extraction techniques are employed to procure heterogeneous health indicators. A pattern recognition algorithm is used to model baseline behavior and measure deviation of current behavior, where a Self-organizing Map (SOM and minimum quantization error (MQE method is selected to achieve degradation assessment. Eventually, the computation and ranking of component contribution to the detected degradation offers component-level fault localization. When validated and automated by various applications, the approach is able to incorporate diverse data resources and output actionable information to advise predictive maintenance with precise fault information. The approach is validated on a 3 MW offshore turbine, where an incipient fault is detected well before existing system shuts down the unit. A radar chart is used to illustrate the fault localization result.

  12. Integration of Hybrid PV/Wind Generation System Using Fuzzy MPPT in Grid Connected System for Remote Area

    Directory of Open Access Journals (Sweden)

    Soedibyo

    2016-01-01

    Full Text Available Photovoltaic and wind are renewable energy resources that widely used and grow rapidly in fulfilling electricity demand. Powers from both technologies depend on sunlight intensity and wind speed. For small scale power generation, DC voltage from both technologies is low and requires step-up converter to raise DC voltage ratio before converted into AC voltage. To optimize this system, step-up converter must have high ratio and efficiency to a distance of wide voltage input. This paper proposed an operation simulation and arrangement of DC-DC converter along with DC-AC from hybrid source PV-Wind which integrated to grid utilities without using storage device. High Gain Integrated Cascade Boost (HGICB is DC-DC converter that has quadratic voltage ratio and used in this research. Then DC link connected to Voltage Source Inverter (VSI which interconnected with utility grid and controlled by current control method. The total installed capacity of hybrid source is 4.4 kW. Wind turbine uses PMSG along with full bridge rectifier. To maximize and stabilize the generated power, MPPT fuzzy is used. Result from the simulation shows that converter capable to maintain maximum power whether from PV and wind turbine which canalized to utility grid in various irradiation condition, wind speed, and grid load alteration.

  13. Integration of Wind Energy, Hydrogen and Natural Gas Pipeline Systems to Meet Community and Transportation Energy Needs: A Parametric Study

    Directory of Open Access Journals (Sweden)

    Shahryar Garmsiri

    2014-04-01

    Full Text Available The potential benefits are examined of the “Power-to-Gas” (P2G scheme to utilize excess wind power capacity by generating hydrogen (or potentially methane for use in the natural gas distribution grid. A parametric analysis is used to determine the feasibility and size of systems producing hydrogen that would be injected into the natural gas grid. Specifically, wind farms located in southwestern Ontario, Canada are considered. Infrastructure requirements, wind farm size, pipeline capacity, geographical dispersion, hydrogen production rate, capital and operating costs are used as performance measures. The model takes into account the potential production rate of hydrogen and the rate that it can be injected into the local gas grid. “Straw man” systems are examined, centered on a wind farm size of 100 MW integrating a 16-MW capacity electrolysis system typically producing 4700 kg of hydrogen per day.

  14. Do urban canyons influence street level grass pollen concentrations?

    Science.gov (United States)

    Peel, Robert George; Kennedy, Roy; Smith, Matt; Hertel, Ole

    2014-08-01

    In epidemiological studies, outdoor exposure to pollen is typically estimated using rooftop monitoring station data, whilst exposure overwhelmingly occurs at street level. In this study the relationship between street level and roof level grass pollen concentrations was investigated for city centre street canyon environments in Aarhus, Denmark, and London, UK, during the grass pollen seasons of 2010 and 2011 respectively. For the period mid-day to late evening, street level concentrations in both cities tended to be lower than roof-level concentrations, though this difference was found to be statistically significant only in London. The ratio of street/roof level concentrations was compared with temperature, relative humidity, wind speed and direction, and solar radiation. Results indicated that the concentration ratio responds to wind direction with respect to relative canyon orientation and local source distribution. In the London study, an increase in relative humidity was linked to a significant decrease in street/roof level concentration ratio, and a possible causative mechanism involving moisture mediated pollen grain buoyancy is proposed. Relationships with the other weather variables were not found to be significant in either location. These results suggest a tendency for monitoring station data to overestimate exposure in the canyon environment. PMID:24037300

  15. On the Impact of Trees on Dispersion Processes of Traffic Emissions in Street Canyons

    Science.gov (United States)

    Gromke, Christof; Ruck, Bodo

    2009-04-01

    Wind-tunnel studies of dispersion processes of traffic exhaust in urban street canyons with tree planting were performed and tracer gas concentrations using electron capture detection (ECD) and flow fields using laser Doppler velocimetry (LDV) were measured. It was found that tree planting reduces the air exchange between street canyons and the ambience. In comparison to treeless street canyons, higher overall pollutant concentrations and lower flow velocities were measured. In particular, for perpendicular approaching wind, markedly higher concentrations at the leeward canyon wall and slightly lower concentrations at the windward canyon wall were observed. Furthermore, a new approach is suggested to model porous vegetative structures such as tree crowns for small-scale wind-tunnel applications. The approach is based on creating different model tree crown porosities by incorporating a certain amount of wadding material into a specified volume. A significant influence of the crown porosity on pollutant concentrations was found for high degrees of porosity, however, when it falls below a certain threshold, no further changes in pollutant concentrations were observed.

  16. Wind Integration into Energy Systems with a High Share of Nuclear Power—What Are the Compromises?

    Directory of Open Access Journals (Sweden)

    Behnam Zakeri

    2015-03-01

    Full Text Available Towards low-carbon energy systems, there are countries with ongoing plans for expanding their nuclear power capacity, and simultaneously advancing the role of variable renewable energy sources (RES, namely wind and solar energy. This crossroads of capital-intensive, baseload power production and uncontrollable, intermittent RES may entail new challenges in the optimal and economic operation of power systems. This study examines this case by hourly analysis of a national-level energy system with the EnergyPLAN modeling tool, coupled with wind integration simulations (including uncertainty implemented using MATLAB. We evaluate the maximum feasible wind integration under different scenarios for nuclear power plants, energy demand, and the flexibility of energy infrastructure for a real case study (Finland. We propose wind-nuclear compromise charts to envision the impact of any mix of these two technologies on four parameters: total costs, power exchange, carbon emissions, and renewable energy integration. The results suggest that nuclear power constrains the room for maximum uptake of wind energy by a descending parabolic relationship. If nuclear power production exceeds 50% of the total power demand, wind will be unlikely to penetrate in shares over 15% of the respective demand. Moreover, we investigate the role of four flexibility options: demand side management, electrical energy storage, smart electric heating, and large-scale heat pumps (backed with thermal energy storage. Heat pumps (which are in connection with combined heat and power (CHP and district heating systems offer the highest efficiency in balancing excess power from variable RES. However, power-to-heat options offer a limited capability for absorbing excess power, as oversupply arises mainly in the periods with relatively low demand for heat. This calls for longer-term energy storage and/or other flexibility options to achieve the planned targets in wind-nuclear scenarios.

  17. NUMERICAL STUDIES ON AIRFLOW AND POLLUTANT DISPERSION IN URBAN STREET CANYONS FORMED BY SLANTED ROOF BUILDINGS

    Institute of Scientific and Technical Information of China (English)

    HUANG Yuan-dong; JIN Ming-xia; SUN Ya-nan

    2007-01-01

    Based on the CFD technique, fifteen cases were evaluated for the airflows and pollutant dispersions inside urban street canyons formed by slanted roof buildings. The simulated wind fields and concentration contours show that W/H, W/h and h/H (where W is the street width, and H and h are the heights of buildings at the leeward and windward sides of the street, respectively) are the crucial factors in determining the vortex structure and pollutant distribution within a canyon. It is concluded that (1) in a symmetrical canyon, at W/H =0.5 two vortices (an upper clockwise vortex between the slanted roofs and a lower counter-clockwise one) are developed and pollutants accumulate on the windward side of the street, whereas at W/H=2.0 only one clockwise vortex is generated and thus pollution piles up on the leeward side, (2) in a step-up canyon with W/H =0.5 to 2.0 (at h/H =1.5 to 2.0)and a step-down canyon with W/h=1.0 (at h/H =0.5 to 0.667), the pollution level close to the lower building is higher than that close to the taller building since a clockwise vortex is generated in the step-up canyon and a counter-clockwise one in the step-down canyon, (3) in a narrow step-down canyon with W/h=0.5 (at h/H =0.667) very poor ventilation properties is detected, and inside a wider step-down canyon with W/h=2.0 the vortex structure and consequently pollutant distribution varies greatly with h/H.

  18. Thermal bioclimate in idealized urban street canyons in Campinas, Brazil

    Science.gov (United States)

    Abreu-Harbich, Loyde V.; Labaki, Lucila C.; Matzarakis, Andreas

    2014-01-01

    Among several urban design parameters, the height-to-width ratio (H/W) and orientation are important parameters strongly affecting thermal conditions in cities. This paper quantifies changes in thermal comfort due to typical urban canyon configurations in Campinas, Brazil, and presents urban guidelines concerning H/W ratios and green spaces to adapt urban climate change. The study focuses on thermal comfort issues of humans in urban areas and performs evaluation in terms of physiologically equivalent temperature (PET), based on long-term data. Meteorological data of air temperature, relative humidity, wind speed and solar radiation over a 7-year period (2003-2010) were used. A 3D street canyon model was designed with RayMan Pro software to simulate the influence of urban configuration on urban thermal climate. The following configurations and setups were used. The model canyon was 500 m in length, with widths 9, 21, and 44 m. Its height varied in steps of 2.5 m, from 5 to 40 m. The canyon could be rotated in steps of 15°. The results show that urban design parameters such as width, height, and orientation modify thermal conditions within street canyons. A northeast-southwest orientation can reduce PET during daytime more than other scenarios. Forestry management and green areas are recommended to promote shade on pedestrian areas and on façades, and to improve bioclimate thermal stress, in particular for H/W ratio less than 0.5. The method and results can be applied by architects and urban planners interested in developing responsive guidelines for urban climate issues.

  19. Editorial: Introduction to Energy Strategy Reviews theme issue “Future Energy Systems and Market Integration of Wind Power”

    NARCIS (Netherlands)

    Lund, H.; Weijermars, R.

    2013-01-01

    Energy Strategy Reviews (ESR) provides a peer-reviewed publication platformto evaluate strategy options for tomorrow’s energy systems. The focus in this special issue is on “Future Energy Systems and Market Integration of Wind Power” and possible solutions are highlighted from the strategy viewpoint

  20. 75 FR 26788 - Public Land Order No. 7742; Withdrawal of Public Land for the Manning Canyon Tailings Repository; UT

    Science.gov (United States)

    2010-05-12

    ... Tailings Repository; UT AGENCY: Bureau of Land Management, Interior. ACTION: Public Land Order. SUMMARY... laws for a period of 5 years to protect the integrity of the Manning Canyon Tailings Repository and... Canyon Tailings Repository. The Bureau of Land Management intends to evaluate the need for a...

  1. Measurement-Based Investigation of Inter- and Intra-Area Effects of Wind Power Plant Integration

    Energy Technology Data Exchange (ETDEWEB)

    Allen, Alicia J.; Singh, Mohit; Muljadi, Eduard; Santoso, Surya

    2016-12-01

    This paper has a two pronged objective: the first objective is to analyze the general effects of wind power plant (WPP) integration and the resulting displacement of conventional power plant (CPP) inertia on power system stability and the second is to demonstrate the efficacy of PMU data in power system stability analyses, specifically when knowledge of the network is incomplete. Traditionally modal analysis applies small signal stability analysis based on Eigenvalues and the assumption of complete knowledge of the network and all of its components. The analysis presented here differs because it is a measurement-based investigation and employs simulated measurement data. Even if knowledge of the network were incomplete, this methodology would allow for monitoring and analysis of modes. This allows non-utility entities and study of power system stability. To generate inter- and intra-area modes, Kundur's well-known two-area four-generator system is modeled in PSCAD/EMTDC. A doubly-fed induction generator based WPP model, based on the Western Electricity Coordination Council (WECC) standard model, is included to analyze the effects of wind power on system modes. The two-area system and WPP are connected in various configurations with respect to WPP placement, CPP inertia and WPP penetration level. Analysis is performed on the data generated by the simulations. For each simulation run, a different configuration is chosen and a large disturbance is applied. The sampling frequency is set to resemble the sampling frequency at which data is available from phasor measurement units (PMUs). The estimate of power spectral density of these signals is made using the Yule-Walker algorithm. The resulting analysis shows that the presence of a WPP does not, of itself, lead to the introduction of new modes. The analysis also shows however that displacement of inertia may lead to introduction of new modes. The effects of location of inertia displacement (i.e. the effects on

  2. Integrating Systems Health Management with Adaptive Controls for a Utility-scale Wind Turbine

    Data.gov (United States)

    National Aeronautics and Space Administration — Increasing turbine up-time and reducing maintenance costs are key technology drivers for wind turbine operators. Components within wind turbines are subject to...

  3. Aerodynamic effects of trees on pollutant concentration in street canyons.

    Science.gov (United States)

    Buccolieri, Riccardo; Gromke, Christof; Di Sabatino, Silvana; Ruck, Bodo

    2009-09-15

    This paper deals with aerodynamic effects of avenue-like tree planting on flow and traffic-originated pollutant dispersion in urban street canyons by means of wind tunnel experiments and numerical simulations. Several parameters affecting pedestrian level concentration are investigated, namely plant morphology, positioning and arrangement. We extend our previous work in this novel aspect of research to new configurations which comprise tree planting of different crown porosity and stand density, planted in two rows within a canyon of street width to building height ratio W/H=2 with perpendicular approaching wind. Sulfur hexafluoride was used as tracer gas to model the traffic emissions. Complementary to wind tunnel experiments, 3D numerical simulations were performed with the Computational Fluid Dynamics (CFD) code FLUENT using a Reynolds Stress turbulence closure for flow and the advection-diffusion method for concentration calculations. In the presence of trees, both measurements and simulations showed considerable larger pollutant concentrations near the leeward wall and slightly lower concentrations near the windward wall in comparison with the tree-less case. Tree stand density and crown porosity were found to be of minor importance in affecting pollutant concentration. On the other hand, the analysis indicated that W/H is a more crucial parameter. The larger the value of W/H the smaller is the effect of trees on pedestrian level concentration regardless of tree morphology and arrangement. A preliminary analysis of approaching flow velocities showed that at low wind speed the effect of trees on concentrations is worst than at higher speed. The investigations carried out in this work allowed us to set up an appropriate CFD modelling methodology for the study of the aerodynamic effects of tree planting in street canyons. The results obtained can be used by city planners for the design of tree planting in the urban environment with regard to air quality issues

  4. Overview of the Energy Storage Systems for the Wind Power Integration Enhancement

    DEFF Research Database (Denmark)

    Swierczynski, Maciej Jozef; Teodorescu, Remus; Rasmussen, Claus Nygaard;

    2010-01-01

    As the installed worldwide wind energy capacity increases about 30% annually and Kyoto protocol that came in force in 2005, wind penetration level in power system is considered to significantly increase in near future. Due to increased penetration and nature of the wind, especially its...

  5. Large-Eddy Simulation of Ventilation and Pollutant Removal in Neutrally and Unstably Stratified Street Canyons

    Science.gov (United States)

    Liu, C.; Cheng, W.; Leung, D. Y.

    2009-12-01

    Large-eddy simulation model was developed to study the ventilation and pollutant removal of urban street canyons in neutral and unstable stratifications. Street canyons of unity building-height-to-street-width ratio were considered. For the case with unstable stratification, the ground was heated up to a Richardson number Rb (= gh/Uh2(Θh-Θ0)/Θref) of -10, where g is the gravitational acceleration, h the building height, Uh the roof-level velocity scale, Θref the reference temperature, Θh the roof-level temperature and Θ0 the ground temperature. The gaseous pollutant was modeled as a passive scalar. Ground-level area sources with uniform pollutant concentrations were used to model traffic emission. In neutral stratification, skimming flow and poor pollutant removal are observed. A primary recirculation is developed in the street canyon core by the prevalent wind (Fig 1a). It occupies nearly all the space inside the street canyon leaving three small secondary recirculations at the ground-level leeward, ground-level windward and roof-level leeward corners. The pollutant emitted from the street is mostly trapped inside the street canyon hence elevated pollutant concentration is observed. Unstable stratification modifies the flow pattern significantly that enhances the pollutant removal. An enlarged secondary recirculation is observed at the ground-level windward corner (Fig 1b). It pushes the primary recirculation upward which eventually extends over the roof level of street canyon immersing into the shear layer aloft. The sizes of the two small recirculations on the leeward side shrink instead. The wind speed inside the street canyon increases that enhances the pollutant mixing. As a result, the overall pollutant concentration is lower compared with that in neutral stratification. In contrast to a roof-level thin layer of pollutant in neutral stratification, pollutant is carried upward by the convective updraft moving from the building roof level into the shear

  6. Pushing the distribution system to its limits and beyond. A case study on wind integration in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Troester, Eckehard; Langanke, Stefan [Energynautics GmbH, Darmstadt (Germany); Betz, Bernhard [EWR Netz GmbH, Worms (Germany)

    2012-07-01

    In the EWR Netz distribution system the installed capacity of renewable energy sources - mainly wind - will most likely triple in the coming ten years. Due to this development it is to be determined how much of the new capacities can be integrated in the existing structure of the medium voltage distribution system. In this paper a case study is described, analyzing the issues that arise when trying to integrate a wind power plant at a size of the cable capacities into the existing infrastructure. Different aspects of the grid connection are evaluated with respect to the German medium voltage grid code: loading of assets voltage profile, power quality and necessity of curtailment. It turns out, that the wind power plant would fail for almost any aspect investigated according to the grid code. However for each aspect a solution can be found: for example, to keep the voltage in allowed limits, a wide area voltage control is recommended. In 2013 the wind power plant will be installed. The operation of the wind power plant will show whether the limits of the German MV grid code can really be safely exceeded. (orig.)

  7. Results from an investigation of the integration of wind energy into the El Paso Electric grid system

    Energy Technology Data Exchange (ETDEWEB)

    Moroz, E.M.; Parks, N.J.; Swift, A.H.; Traichal, P.A. [Univ. of Texas, El Paso, TX (United States)

    1997-12-31

    This paper documents some preliminary results from an evaluation of the costs and benefits to be gained from the integration of wind generated electricity into the El Paso Electric grid system. The study focused on the utilization of the considerable known wind potential of the Guadalupe/Delaware Mountains region, but also looked at other energetic wind resources within 15 miles of El Paso Electric`s Grid. The original project`s goal was to identify the added value of wind in terms of jobs, line support, risk reduction etc., that wind energy could bring to El Paso Electric. Although these goals have not yet been achieved the potential for water savings and reductions in gaseous emissions have been documented. Thus this paper focuses mainly on the water consumption and criteria pollutant emissions that could be avoided by adding wind energy to El Paso Electric`s generation mix. Preliminary data from a renewables attitude survey indicates that, from the 338 respondents, there is overwhelming public support for utilizing such renewable sources of electricity. This case study, which should be of direct relevance to the arid southwestern states and beyond, was sponsored by the Environmental Protection Agency (EPA) and conducted in cooperation with El Paso Electric.

  8. Markets to Facilitate Wind and Solar Energy Integration in the Bulk Power Supply: An IEA Task 25 Collaboration; Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Milligan, M.; Holttinen, H.; Soder, L.; Clark, C.; Pineda, I.

    2012-09-01

    Wind and solar power will give rise to challenges in electricity markets regarding flexibility, capacity adequacy, and the participation of wind and solar generators to markets. Large amounts of wind power will have impacts on bulk power system markets and electricity prices. If the markets respond to increased wind power by increasing investments in low-capital, high-cost or marginal-cost power, the average price may remain in the same range. However, experiences so far from Denmark, Germany, Spain, and Ireland are such that the average market prices have decreased because of wind power. This reduction may result in additional revenue insufficiency, which may be corrected with a capacity market, yet capacity markets are difficult to design. However, the flexibility attributes of the capacity also need to be considered. Markets facilitating wind and solar integration will include possibilities for trading close to delivery (either by shorter gate closure times or intraday markets). Time steps chosen for markets can enable more flexibility to be assessed. Experience from 5- and 10-minute markets has been encouraging.

  9. Large-scale wind power integration and wholesale electricity trading benefits: Estimation via an ex post approach

    International Nuclear Information System (INIS)

    The integration of large-scale wind power has brought about a series of challenges to the power industry, but at the same time a number of benefits are being realized. Among those, the ability of wind power to cause a decline in the electricity market prices has been recognized. In quantifying this effect, some models used in recent years are based on simulations of the market supply-side and the price clearing process. The accuracy of the estimates depend on the quality of the input data, the veracity of the adopted scenarios and the rigorousness of the solution technique. In this work, a series of econometric techniques based on actual ex post wind power and electricity price data are implemented for the estimation of the impact of region-wide wind power integration on the local electricity market clearing prices and the trading savings that stem from this effect. The model is applied to the case of Spain, where the estimated savings are compared against actual credit and bonus expenses to ratepayers. The implications and extent of these results for current and future renewable energy policy-making are discussed. - Highlights: ► Wholesale electricity market trading benefits by wind power are quantified. ► Actual wind power forecast-based bids and electricity price data from Spain are used. ► Different econometric tools are used and compared for improved estimation accuracy. ► Estimated benefits outweigh current credit overhead paid to wind farms in Spain. An economically efficient benefit surplus allocation framework is proposed.

  10. Wind Energy Management System EMS Integration Project: Incorporating Wind Generation and Load Forecast Uncertainties into Power Grid Operations

    Energy Technology Data Exchange (ETDEWEB)

    Makarov, Yuri V.; Huang, Zhenyu; Etingov, Pavel V.; Ma, Jian; Guttromson, Ross T.; Subbarao, Krishnappa; Chakrabarti, Bhujanga B.

    2010-01-01

    The power system balancing process, which includes the scheduling, real time dispatch (load following) and regulation processes, is traditionally based on deterministic models. Since the conventional generation needs time to be committed and dispatched to a desired megawatt level, the scheduling and load following processes use load and wind and solar power production forecasts to achieve future balance between the conventional generation and energy storage on the one side, and system load, intermittent resources (such as wind and solar generation), and scheduled interchange on the other side. Although in real life the forecasting procedures imply some uncertainty around the load and wind/solar forecasts (caused by forecast errors), only their mean values are actually used in the generation dispatch and commitment procedures. Since the actual load and intermittent generation can deviate from their forecasts, it becomes increasingly unclear (especially, with the increasing penetration of renewable resources) whether the system would be actually able to meet the conventional generation requirements within the look-ahead horizon, what the additional balancing efforts would be needed as we get closer to the real time, and what additional costs would be incurred by those needs. To improve the system control performance characteristics, maintain system reliability, and minimize expenses related to the system balancing functions, it becomes necessary to incorporate the predicted uncertainty ranges into the scheduling, load following, and, in some extent, into the regulation processes. It is also important to address the uncertainty problem comprehensively by including all sources of uncertainty (load, intermittent generation, generators’ forced outages, etc.) into consideration. All aspects of uncertainty such as the imbalance size (which is the same as capacity needed to mitigate the imbalance) and generation ramping requirement must be taken into account. The latter

  11. Grid integration study of a wind farm in a 220 kV grid

    Energy Technology Data Exchange (ETDEWEB)

    Teixeira, E.; Alvarez-Ortega, C. [Energy to Quality, S.L., Madrid (Spain)

    2012-07-01

    An electrical feasibility study of a wind farm project in a 220 kV grid is presented. Present and future high voltage grid is studied. The comparison of the main electrical parameters between the electrical grid with and without the addition of a 120 MW wind farm is performed in order to demonstrate that the wind farm is performed in order to demonstrate that the wind farm has no negative effects over the transmission system. The obtained results allow concluding that the wind farm under study will not cause significant perturbations on the power grid. (orig.)

  12. Integrating Wind Profiling Radars and Radiosonde Observations with Model Point Data to Develop a Decision Support Tool to Assess Upper-Level Winds for Space Launch

    Science.gov (United States)

    Bauman, William H., III; Flinn, Clay

    2013-01-01

    On the day-of-launch, the 45th Weather Squadron (45 WS) Launch Weather Officers (LWOs) monitor the upper-level winds for their launch customers to include NASA's Launch Services Program and NASA's Ground Systems Development and Operations Program. They currently do not have the capability to display and overlay profiles of upper-level observations and numerical weather prediction model forecasts. The LWOs requested the Applied Meteorology Unit (AMU) develop a tool in the form of a graphical user interface (GUI) that will allow them to plot upper-level wind speed and direction observations from the Kennedy Space Center (KSC) 50 MHz tropospheric wind profiling radar, KSC Shuttle Landing Facility 915 MHz boundary layer wind profiling radar and Cape Canaveral Air Force Station (CCAFS) Automated Meteorological Processing System (AMPS) radiosondes, and then overlay forecast wind profiles from the model point data including the North American Mesoscale (NAM) model, Rapid Refresh (RAP) model and Global Forecast System (GFS) model to assess the performance of these models. The AMU developed an Excel-based tool that provides an objective method for the LWOs to compare the model-forecast upper-level winds to the KSC wind profiling radars and CCAFS AMPS observations to assess the model potential to accurately forecast changes in the upperlevel profile through the launch count. The AMU wrote Excel Visual Basic for Applications (VBA) scripts to automatically retrieve model point data for CCAFS (XMR) from the Iowa State University Archive Data Server (http://mtarchive.qeol.iastate.edu) and the 50 MHz, 915 MHz and AMPS observations from the NASA/KSC Spaceport Weather Data Archive web site (http://trmm.ksc.nasa.gov). The AMU then developed code in Excel VBA to automatically ingest and format the observations and model point data in Excel to ready the data for generating Excel charts for the LWO's. The resulting charts allow the LWOs to independently initialize the three models 0

  13. High-Throughput Computation and the Applicability of Monte Carlo Integration in Fatigue Load Estimation of Floating Offshore Wind Turbines

    Energy Technology Data Exchange (ETDEWEB)

    Graf, Peter A.; Stewart, Gordon; Lackner, Matthew; Dykes, Katherine; Veers, Paul

    2016-05-01

    Long-term fatigue loads for floating offshore wind turbines are hard to estimate because they require the evaluation of the integral of a highly nonlinear function over a wide variety of wind and wave conditions. Current design standards involve scanning over a uniform rectangular grid of metocean inputs (e.g., wind speed and direction and wave height and period), which becomes intractable in high dimensions as the number of required evaluations grows exponentially with dimension. Monte Carlo integration offers a potentially efficient alternative because it has theoretical convergence proportional to the inverse of the square root of the number of samples, which is independent of dimension. In this paper, we first report on the integration of the aeroelastic code FAST into NREL's systems engineering tool, WISDEM, and the development of a high-throughput pipeline capable of sampling from arbitrary distributions, running FAST on a large scale, and postprocessing the results into estimates of fatigue loads. Second, we use this tool to run a variety of studies aimed at comparing grid-based and Monte Carlo-based approaches with calculating long-term fatigue loads. We observe that for more than a few dimensions, the Monte Carlo approach can represent a large improvement in computational efficiency, but that as nonlinearity increases, the effectiveness of Monte Carlo is correspondingly reduced. The present work sets the stage for future research focusing on using advanced statistical methods for analysis of wind turbine fatigue as well as extreme loads.

  14. The economics of wind and solar variability. How the variability of wind and solar power affects their marginal value, optimal deployment, and integration costs

    Energy Technology Data Exchange (ETDEWEB)

    Hirth, Lion

    2014-11-14

    Variable renewable energy sources (VRE) for electricity generation, such as wind and solar power, are subject to inherent output fluctuations. This variability has significant impacts on power system and electricity markets if VRE are deployed at large scale. While on global average, wind and solar power currently supply only a minor share of electricity, they are expected to play a much larger role in the future - such that variability will become a major issue (which it already is in some regions). This thesis contributes to the literature that assesses these impacts the ''system and market integration'' literature. This thesis aims at answering the question: What is the impact of wind and solar power variability on the economics of these technologies? It will be laid out that the impact can be expressed in (at least) three ways: as reduction of value, as increase of cost, or as decrease of optimal deployment. Translating between these perspectives is not trivial, as evidenced by the confusion around the concept of ''integration costs''. Hence, more specifically: How does variability impact the marginal economic value of these power sources, their optimal deployment, and their integration costs? This is the question that this thesis addresses. This study comprises six papers, of which two develop a valuation framework that accounts for the specific characteristics of the good electricity, and the specific properties of wind and solar power versus ''dispatchable'' power plants. Three articles then assess quantitative questions and estimate marginal value, optimal deployment, and integration costs. These estimates stem from a newly developed numerical power market model, EMMA, market data, and quantitative literature reviews. The final paper addresses market design. In short, the principal findings of this thesis are as follows. Electricity is a peculiar economic good, being at the same time perfectly

  15. The economics of wind and solar variability. How the variability of wind and solar power affects their marginal value, optimal deployment, and integration costs

    International Nuclear Information System (INIS)

    Variable renewable energy sources (VRE) for electricity generation, such as wind and solar power, are subject to inherent output fluctuations. This variability has significant impacts on power system and electricity markets if VRE are deployed at large scale. While on global average, wind and solar power currently supply only a minor share of electricity, they are expected to play a much larger role in the future - such that variability will become a major issue (which it already is in some regions). This thesis contributes to the literature that assesses these impacts the ''system and market integration'' literature. This thesis aims at answering the question: What is the impact of wind and solar power variability on the economics of these technologies? It will be laid out that the impact can be expressed in (at least) three ways: as reduction of value, as increase of cost, or as decrease of optimal deployment. Translating between these perspectives is not trivial, as evidenced by the confusion around the concept of ''integration costs''. Hence, more specifically: How does variability impact the marginal economic value of these power sources, their optimal deployment, and their integration costs? This is the question that this thesis addresses. This study comprises six papers, of which two develop a valuation framework that accounts for the specific characteristics of the good electricity, and the specific properties of wind and solar power versus ''dispatchable'' power plants. Three articles then assess quantitative questions and estimate marginal value, optimal deployment, and integration costs. These estimates stem from a newly developed numerical power market model, EMMA, market data, and quantitative literature reviews. The final paper addresses market design. In short, the principal findings of this thesis are as follows. Electricity is a peculiar economic good, being at the same time perfectly

  16. The transport sectors potential contribution to the flexibility in the power sector required by large-scale wind power integration

    DEFF Research Database (Denmark)

    Nørgaard, Per; Lund, Henrik; Mathiesen, Brian Vad

    2007-01-01

    -scale integration of renewable energy in the power system – in specific wind power. In the plan, 20 % of the road transport is based on electricity and 20 % on bio- fuels. This, together with other initiatives allows for up to 55-60 % wind power penetration in the power system. A fleet of 0.5 mio electrical......In 2006, the Danish Society of Engineers developed a visionary plan for the Danish energy system in 2030. The paper presents and qualifies selected part of the analyses, illustrating the transport sectors potential to contribute to the flexibility in the power sector, necessary for large...

  17. Impact of aspect ratio and solar heating on street canyon air temperature

    International Nuclear Information System (INIS)

    The results obtained from RNG (Re-Normalization Group) version of k-and turbulence model are reported in this study. The model is adopted to elucidate the impact of different building aspect ratios (i.e., ratio of building-height-to-street-canyon-width) and solar heating on temperatures in street canyon. The validation of Navier-Stokes and energy an sport equations showed that the model prediction for air-temperature and ambient wind provides reasonable accuracy. The model was applied on AR (Aspect Ratios) one to eight and surface temperature difference (delta and theta/sub s-a/)) of 2 -8. Notably, air-temperatures were higher in high AR street canyons in particular on the leeward side of the street canyon. Further investigation showed that the difference between the air-temperature 'high and low AR street canyons (AR) was positive and high with higher delta and theta/sub s-a/) conversely, the AR become negative and low gradually with lower values of delta and theta(/sub s-a/). These results could be very beneficial for the city and regional planners, civil engineers Id HVAC experts who design street canyons and strive for human thermal comfort with minimum possible energy requirements. (author)

  18. Near-inertial motions in the DeSoto Canyon during Hurricane Georges

    Science.gov (United States)

    Jordi, Antoni; Wang, Dong-Ping; Hamilton, Peter

    2016-09-01

    Hurricane Georges passed directly over an array of 13 moorings deployed in the DeSoto Canyon in the northern Gulf of Mexico on 27-28 September 1998. Current velocity data from the mooring array were analyzed together with a primitive-equation model simulation with realistic hurricane forcing, to characterize the generation and propagation of the hurricane-generated near-inertial waves. The model successfully reproduces the observed mean (sub-inertial) and near-inertial motions. The upper ocean response is strongly impacted by the canyon 'wall': a strong jet is formed along the slope, and the near-inertial motions on the shelf are rapidly suppressed. The model results moreover suggest that strong near-inertial waves in the mixed layer are mostly trapped in an energy flux recirculating gyre around the canyon. This gyre retains the near-inertial energy in the canyon region and enhances the transfer of near-inertial energy below the mixed layer. Additional simulations with idealized topographies show that the presence of a steep slope rather than the canyon is fundamental for the generation of this recirculating gyre. The near-inertial wave energy budget shows that during the study period the wind generated an input of 6.79 × 10-2 Wm-2 of which about 1/3, or 2.43 × 10-2 Wm-2, was transferred below the mixed layer. The horizontal energy flux into and out of the canyon region, in contrast, was relatively weak.

  19. An Innovative Technique for Evaluating the Integrity and Durability of Wind Turbine Blade Composites

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jy-An John [ORNL; Ren, Fei [ORNL

    2010-09-01

    Wind turbine blades are subjected to complex multiaxial stress states during operation. A review of the literature suggests that mixed mode fracture toughness can be significantly less than that of the tensile opening mode (Mode I), implying that fracture failure can occur at a much lower load capacity if the structure is subject to mixed-mode loading. Thus, it will be necessary to identify the mechanisms that might lead to failure in blade materials under mixed-mode loading conditions. Meanwhile, wind turbine blades are typically fabricated from fiber reinforced polymeric materials, e.g. fiber glass composites. Due to the large degree of anisotropy in mechanical properties that is usually associated with laminates, the fracture behavior of these composite materials is likely to be strongly dependent on the loading conditions. This may further strengthen the need to study the effect of mixed-mode loading on the integrity and durability of the wind turbine blade composites. To quantify the fracture behavior of composite structures under mixed mode loading conditions, particularly under combined Mode I (flexural or normal tensile stress) and Mode III (torsional shear stress) loading, a new testing technique is proposed based on the spiral notch torsion test (SNTT). As a 2002 R&D 100 Award winner, SNTT is a novel fracture testing technology. SNTT has many advantages over conventional fracture toughness methods and has been used to determine fracture toughness values on a wide spectrum of materials. The current project is the first attempt to utilize SNTT on polymeric and polymer-based composite materials. It is expected that mixed-mode failure mechanisms of wind turbine blades induced by typical in-service loading conditions, such as delamination, matrix cracking, fiber pull-out and fracture, can be effectively and economically investigated by using this methodology. This project consists of two phases. The Phase I (FY2010) effort includes (1) preparation of testing

  20. OPTIMIZING LAYOUT OF URBAN STREET CANYON USING NUMERICAL SIMULATION COUPLING WITH MATHEMATICAL OPTIMIZATION

    Institute of Scientific and Technical Information of China (English)

    WANG Jia-song; ZHAO Bao-qing; YE Chun; YANG De-qing; HUANG Zhen

    2006-01-01

    Optimizing the layout of the urban street canyon to achieve the maximum environmental benefits should become a new idea for modern urban street design and planning. This paper aims to find out the optimized street canyon from a viewpoint of environmental protection by using the two-dimensional numerical simulation model with the turbulence model, coupling with the mathematical optimization method. The total pollutant concentration within and at top of the specific street canyons was taken as the objective function, and the height of one side of the canyon as the constrained condition. A nonlinearly improved constrained variable metric solver was used. The effect of the height of the leeward building and windward building on the integrated pollutant dispersion was studied to achieve the most beneficial configuration of the urban geometry. The optimization of layout for an asymmetrical street canyon was obtained. It is further found that the step-down street canyon with a large height difference is generally a good layout favoring to reduce the concentration accumulation in the street canyon.

  1. Review and Status of Wind Integration and Transmission in the United States. Key Issues and Lessons Learned

    Energy Technology Data Exchange (ETDEWEB)

    Milligan, M. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kirby, B. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Acker, T. [Northern Arizona Univ., Flagstaff, AZ (United States); Ahlstrom, M. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Frew, B. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Goggin, M. [American Wind Energy Association, Washington, DC (United States); Lasher, W. [Electric Reliability Council of Texas, Austin, TX (United States); Marquis, M. [National Oceanic and Atmospheric Adminstration, Washington, DC (United States); Osborn, D. [Midcontinent Independent System Operator, Carmel, IN (United States)

    2015-03-01

    The objective in electric power system operation is to use generation and transmission resources within organizational constraints and operational rules and regulations to reliably and costeffectively balance load and generation. To meet this objective, system operational practices have been created to accommodate the innate variability and uncertainty that comes from a variety of sources, such as uncertainty of demand forecasts, whether a specific generating unit will be available when called upon, the variability of demand from many different types of customers, and others. As more wind power is connected to the power system, operating experiences acquired during the past several years have generally confirmed the findings of wind integration studies: wind energy increases the level of variability and uncertainty that a system operator must manage.

  2. Aerodynamic and Structural Integrated Optimization Design of Horizontal-Axis Wind Turbine Blades

    Directory of Open Access Journals (Sweden)

    Jie Zhu

    2016-01-01

    Full Text Available A procedure based on MATLAB combined with ANSYS is presented and utilized for the aerodynamic and structural integrated optimization design of Horizontal-Axis Wind Turbine (HAWT blades. Three modules are used for this purpose: an aerodynamic analysis module using the Blade Element Momentum (BEM theory, a structural analysis module employing the Finite Element Method (FEM and a multi-objective optimization module utilizing the non-dominated sorting genetic algorithm. The former two provide a sufficiently accurate solution of the aerodynamic and structural performances of the blade; the latter handles the design variables of the optimization problem, namely, the main geometrical shape and structural parameters of the blade, and promotes function optimization. The scope of the procedure is to achieve the best trade-off performances between the maximum Annual Energy Production (AEP and the minimum blade mass under various design requirements. To prove the efficiency and reliability of the procedure, a commercial 1.5 megawatt (MW HAWT blade is used as a case study. Compared with the original scheme, the optimization results show great improvements for the overall performance of the blade.

  3. Street canyon flow patterns in a horizontal plane : measurements from the Joint URBAN 2003 field experiment

    Energy Technology Data Exchange (ETDEWEB)

    Brown, M. J. (Michael J.); Khalsa, H. S. (Hari S.); Nelson, M. A. (Matthew Aaron); Boswell, D. (David)

    2004-01-01

    As part of the larger Joint URBAN 2003 tracer field experiment performed in Oklahoma City from June 29 to July 30, 2003, a collaborative team of government and university researchers instrumented a downtown street canyon with a high density of wind sensor instrumentation (Brown et al., 2003). The goal of the Park Avenue street canyon experiment was to garner flow field information in order to better understand the transport and dispersion of tracers released in the street canyon and to test and improve the next generation of urban dispersion models. In this paper, we focus on describing the mean flow patterns that developed in the street canyon in a horizontal plane near the surface. We look at the patterns that develop over entire Intensive Operating Periods (IOP's) lasting from 6-9 hours in length, and as a function of inflow wind direction. Most prior street canyon experiments have generally focused on the vertical structure of the flow; this work contributes to the understanding of the horizontal nature of the flow.

  4. A quantitative analysis of the net benefits of grid integrated wind

    OpenAIRE

    DENNY, ELEANOR; Bryans, Garth; Fitz Gerald, John; O'Malley, Mark

    2006-01-01

    Throughout the world significant development is being encouraged in wind energy for electricity generation. A complete cost and benefit analysis has been conducted in this paper on grid connected wind generation. It takes into account system costs such as reserve requirements, start-up and ramping implications for conventional plants as well as wear and tear costs. The benefits of wind generation analysed include the emissions benefits, the saving on the fuel bill, the electricity generated a...

  5. Wind-To-Hydrogen Project: Operational Experience, Performance Testing, and Systems Integration

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, K. W.; Martin, G. D.; Ramsden, T. G.; Kramer, W. E.; Novachek, F. J.

    2009-03-01

    The Wind2H2 system is fully functional and continues to gather performance data. In this report, specifications of the Wind2H2 equipment (electrolyzers, compressor, hydrogen storage tanks, and the hydrogen fueled generator) are summarized. System operational experience and lessons learned are discussed. Valuable operational experience is shared through running, testing, daily operations, and troubleshooting the Wind2H2 system and equipment errors are being logged to help evaluate the reliability of the system.

  6. How to make the production of methanol/DME "GREENER"-Integration of wind power with modern coal chemical industry

    Institute of Scientific and Technical Information of China (English)

    Weidou NI; Jian GAO; Zhen CHEN; Zheng LI

    2009-01-01

    The urgency and necessity of alternative fuels give an impetus to the development of modern coal chemical industry. Coal-based methanol/DME is the key element of this industry. Wind power, whose installed capacity increased at a rate of more than 100% in recent years, has the most developed technologies in renewable energy. However, there still exist many unsolved problems in wind power for on-grid utilization. A new integrated system which combines coal-based methanol/DME production with wind power is proposed in this paper. In this system, wind power is used to electrolyze water to produce H2 and O2. The O2 is fed to the gasifier as gasification agent. The H2 is mixed with the CO-rich gas to adjust the H2/CO to an appropriate ratio for methanol synthesis. In comparison with conventional coal-based methanol/DME system, the proposed system omits the expensive and energy-consuming ASU and greatly reduces the water gas shift process, which brings both advantages in the utilization of all raw materials and significant mitigation of CO2 emission. This system will be attractive in the regions of China which have abundant wind and coal resources.

  7. A New Control Method to Mitigate Power Fluctuations for Grid Integrated PV/Wind Hybrid Power System Using Ultracapacitors

    Science.gov (United States)

    Jayalakshmi, N. S.; Gaonkar, D. N.

    2016-08-01

    The output power obtained from solar-wind hybrid system fluctuates with changes in weather conditions. These power fluctuations cause adverse effects on the voltage, frequency and transient stability of the utility grid. In this paper, a control method is presented for power smoothing of grid integrated PV/wind hybrid system using ultracapacitors in a DC coupled structure. The power fluctuations of hybrid system are mitigated and smoothed power is supplied to the utility grid. In this work both photovoltaic (PV) panels and the wind generator are controlled to operate at their maximum power point. The grid side inverter control strategy presented in this paper maintains DC link voltage constant while injecting power to the grid at unity power factor considering different operating conditions. Actual solar irradiation and wind speed data are used in this study to evaluate the performance of the developed system using MATLAB/Simulink software. The simulation results show that output power fluctuations of solar-wind hybrid system can be significantly mitigated using the ultracapacitor based storage system.

  8. SYCAMORE CANYON PRIMITIVE AREA, ARIZONA.

    Science.gov (United States)

    Huff, Lyman C.; Raabe, R.C.

    1984-01-01

    The Sycamore Canyon Primitive Area, which occupies about 74 sq mi, lies about 24 mi southwest of Flagstaff, Arizona. To help evaluate the area for mineral resources, sediment samples were collected along Sycamore Creek and its tributaries. These were analyzed for traces of the ore metals without finding any local concentrations. In addition, a scintillometer was used to test rocks in the area without finding any abnormal radioactivity.

  9. Marble Canyon spring sampling investigation

    International Nuclear Information System (INIS)

    The Mississippian Leadville Limestone is the most permeable formation in the lower hydrostratigraphic unit underlying the salt beds of the Paradox Formation in Gibson Dome, Paradox Basin, Utah, which is being considered as a potential nuclear waste repository site. The closest downgradient outcrop of the Mississippian limestone is along the Colorado River in Marble Canyon, Arizona. This report describes the sampling and interpretation of springs in that area to assess the relative contribution of Gibson Dome-type Leadville Limestone ground water to that spring discharge. The high-volume (hundreds of liters per second or thousands of gallons per minute) springs discharging from fault zones in Marble Canyon are mixtures of water recharged west of the Colorado River on the Kaibab Plateau and east of the river in the Kaiparowits basin. No component of Gibson Dome-type Leadville Limestone ground water is evident in major and trace element chemistry or isotopic composition of the Marble Canyon Springs. A low-volume (0.3 liters per second or 5 gallons per minute) spring with some chemical and isotopic characteristics of Gibson Dome-type Leadville Limestone water diluted by Kaiparowits basin-type water issues from a travertine mound in the Bright Angel Shale on the Little Colorado River. However, the stable isotopic composition and bromide levels of that spring discharge, in addition to probable ground-water flow paths, contradict the dilution hypothesis

  10. Design gridlines for integrated aeroelastic control of wind turbines - Task-12 report

    DEFF Research Database (Denmark)

    Mogensen, T.S.; Larsen, A.J.; Poulsen, N.K.;

    The presented design guidelines for active aeroelastic control of PRVS wind turbines are derived by the partners of the project - Aeroelastic Stability and Control of Large Wind Turbines” (STABCON) partially funded by the European Commission (EC) under the contract NNK5-CT2002-00627. The objective...... of this successful long term research cooperation....

  11. Initial Economic Analysis of Utility-Scale Wind Integration in Hawaii

    Energy Technology Data Exchange (ETDEWEB)

    2012-03-01

    This report summarizes an analysis, conducted by the National Renewable Energy Laboratory (NREL) in May 2010, of the economic characteristics of a particular utility-scale wind configuration project that has been referred to as the 'Big Wind' project.

  12. Quality Control Algorithms and Proposed Integration Process for Wind Profilers Used by Launch Vehicle Systems

    Science.gov (United States)

    Decker, Ryan; Barbre, Robert E., Jr.

    2011-01-01

    Impact of winds to space launch vehicle include Design, Certification Day-of-launch (DOL) steering commands (1)Develop "knockdowns" of load indicators (2) Temporal uncertainty of flight winds. Currently use databases from weather balloons. Includes discrete profiles and profile pair datasets. Issues are : (1)Larger vehicles operate near design limits during ascent 150 discrete profiles per month 110-217 seasonal 2.0 and 3.5-hour pairs Balloon rise time (one hour) and drift (up to 100 n mi) Advantages of the Alternative approach using Doppler Radar Wind Profiler (DRWP) are: (1) Obtain larger sample size (2) Provide flexibility for assessing trajectory changes due to winds (3) Better representation of flight winds.

  13. Integrating GIS with fuzzy multi-criteria decision making for suitable wind farm locations

    Energy Technology Data Exchange (ETDEWEB)

    Iyappan, L.; Pandian, P.K. [Tagore Engineering College. Dept. of Civil Engineering, Tamil Nadu (India)

    2012-07-01

    Wind Energy is spatial in nature and the degree of potential wind farm locations are fuzzy i.e., the boundaries among highly, moderate and least suitable is not clear cut. The study area of this research covers entire taluk of Tirumangalam, Madurai District (India). In this study, to help wind energy companies, policy-makers and investors in evaluating potential wind farm locations in the Tirumangalam Taluk (Tamil Nadu, India), an adaptation of a Geographical Information System (GIS) and Fuzzy Multi-criteria Decision Making(FMDM) approach is attended. The entire processes were completed by using open source GIS software (Quantum GIS and GRASS GIS) with help of freely available data. The software tool takes inputs such as wind power density, Slope, Transmission lines, environmental factors, and economic factors to provide an in-depth analysis for suitable location options. (Author)

  14. Manufacturing technology of integrated textile-based sensor networks for in situ monitoring applications of composite wind turbine blades

    Science.gov (United States)

    Haentzsche, Eric; Mueller, Ralf; Huebner, Matthias; Ruder, Tristan; Unger, Reimar; Nocke, Andreas; Cherif, Chokri

    2016-10-01

    Based on in situ strain sensors consisting of piezo-resistive carbon filament yarns (CFYs), which have been successfully integrated into textile reinforcement structures during their textile-technological manufacturing process, a continuous load of fibre-reinforced plastic (FRP) components has been realised. These sensors are also suitable for structural health monitoring (SHM) applications. The two-dimensional sensor layout is made feasible by the usage of a modular warp yarn path manipulation unit. Using a functional model of a small wind turbine blade in thermoset composite design, the sensor function for basic SHM applications (e.g. static load monitoring) are demonstrated. Any mechanical loads along the pressure or suction side of the wind turbine blade can be measured and calculated via a correlative change in resistance of the CFYs within the textile reinforcement plies. Performing quasi-static load tests on both tensile specimen and full-scale wind turbine blade, elementary results have been obtained concerning electro-mechanical behaviour and spatial resolution of global and even local static stresses according to the CFY sensor integration length. This paper demonstrates the great potential of textile-based and textile-technological integrated sensors in reinforcement structures for future SHM applications of FRPs.

  15. Numerical modeling of flow and pollutant dispersion in street canyons with tree planting

    Energy Technology Data Exchange (ETDEWEB)

    Balczo, Marton [Budapest Univ. of Technology and Economics (Hungary). Theodore von Karman Wind Tunnel Lab.; Gromke, Christof; Ruck, Bodo [Karlsruhe Univ. (Germany). Lab. of Building- and Environmental Aerodynamics

    2009-04-15

    Numerical simulations of the impact of tree planting on airflow and traffic pollutant dispersion in urban street canyons have been performed using the commercial CFD (Computational Fluid Dynamics) code MISKAM. A {kappa}-{epsilon} turbulence model including additional terms for the treatment of vegetation, has been employed to close the Reynolds-averaged-Navier-Stokes (RANS) equations. The numerical results were compared to wind tunnel data. In the case of the investigated wind direction perpendicular to the street axis, the presence of trees lead to increased pollutant concentrations inside the canyon. Concentrations increased strongly on the upstream side of the canyon, while on the downstream side a small concentration decrease could be observed. Lower flow velocities and higher pollutant concentrations were found in the numerical simulations when directly compared to the experimental results. However, the impact of tree planting on airflow and concentration fields when compared to the treeless street canyon as a reference configuration were simulated quite well, meaning that relative changes were similar in the wind tunnel investigations and numerical computations. This feature qualifies MISKAM for use as a tool for assessing the impacts of vegetation on local air quality. (orig.)

  16. Integrated single crystal laser ablation U/Pb and (U-Th)/He dating of detrital accessory minerals - Proof-of-concept studies of titanites and zircons from the Fish Canyon tuff

    Science.gov (United States)

    Horne, Alexandra M.; van Soest, Matthijs C.; Hodges, Kip V.; Tripathy-Lang, Alka; Hourigan, Jeremy K.

    2016-04-01

    Excimer laser technologies enable a rapid and effective approach to simultaneous U/Pb geochronology and (U-Th)/He thermochronology of a wide range of detrital accessory minerals. Here we describe the 'laser ablation double dating' (LADD) method and demonstrate its viability by applying it to zircon and titanite crystals from the well-characterized Fish Canyon tuff. We found that LADD dates for Fish Canyon zircon (206Pb/238U - 28.63 ± 0.11 Ma; (U-Th)/He - 28.38 ± 0.73 Ma) are statistically indistinguishable from those obtained through established, traditional methods of single-crystal dating. The same is true for Fish Canyon titanite LADD dates: 206Pb/238U - 28.08 ± 0.90 Ma; (U-Th)/He - 27.98 ± 0.86 Ma. As anticipated, given that LADD involves the analysis of smaller amounts of material than traditional methods, it yields dates with higher analytical uncertainty. However, this does not substantially reduce the utility of the results for most applications to detrital datasets. An important characteristic of LADD is that it encourages the chemical characterization of crystals by backscattered electron, cathodoluminescence, and/or Raman mapping prior to dating. In addition, by permitting the rapid and robust dating of crystals regardless of the degree of their abrasion during sedimentary transport, the method theoretically should yield dates that are more broadly representative of those of the entire population of detrital crystals in a natural sample.

  17. Studies on reactor piping integrity during severe accident in WIND project

    International Nuclear Information System (INIS)

    In a severe accident of a light water reactor, the reactor coolant piping might be subjected to thermal loads resulted from decay heat release of the deposited fission products, and heat transfer from high temperature gases generated in the reactor core region in addition to an internal pressure load. Thermal and structural responses of the reactor coolant piping under elevated temperature and pressure conditions are being investigated in piping integrity tests in WIND (Wide Range Piping Integrity Demonstration) project at Japan Atomic Energy Research Institute. Four piping failure tests have been conducted using straight stainless steel pipes with a diameter of 114.3mm or 355.6mm which simulate a part of the reactor coolant piping. In a recent failure test in which a pipe with an outer diameter of 355.6mm and a wall thickness of 35.7mm was used and an internal pressure was kept at 10MPa, a failure of the pipe was observed when the maximum temperature of the pipe reached 1040degC after the temperature was sustained at 1000degC for about one hour. Several small openings were formed at the pipe failure in an area showing the maximum temperature. A history of the change in a vertical diameter was obtained from the measurement of displacement at the top and the bottom of the pipe at the center of heated area. An acceleration of piping ballooning was observed when the maximum temperature of the pipe became approximately 1000degC. It was confirmed in post-test observation that the pipe diameter in vertical and horizontal direction was remarkably enlarged and the pipe wall thickness was largely reduced. In parallel with the tests, a post-test analysis was performed using ABAQUS code. The results from 2D elasto-plastic creep analysis for a piping failure test with an outer diameter of 114.3mm and a wall thickness of 13.5mm qualitatively reproduced the final deformation including the diameter enlargement and the wall thinning. (author)

  18. Study of the integration of wind tunnel and computational methods for aerodynamic configurations

    Science.gov (United States)

    Browne, Lindsey E.; Ashby, Dale L.

    1989-01-01

    A study was conducted to determine the effectiveness of using a low-order panel code to estimate wind tunnel wall corrections. The corrections were found by two computations. The first computation included the test model and the surrounding wind tunnel walls, while in the second computation the wind tunnel walls were removed. The difference between the force and moment coefficients obtained by comparing these two cases allowed the determination of the wall corrections. The technique was verified by matching the test-section, wall-pressure signature from a wind tunnel test with the signature predicted by the panel code. To prove the viability of the technique, two cases were considered. The first was a two-dimensional high-lift wing with a flap that was tested in the 7- by 10-foot wind tunnel at NASA Ames Research Center. The second was a 1/32-scale model of the F/A-18 aircraft which was tested in the low-speed wind tunnel at San Diego State University. The panel code used was PMARC (Panel Method Ames Research Center). Results of this study indicate that the proposed wind tunnel wall correction method is comparable to other methods and that it also inherently includes the corrections due to model blockage and wing lift.

  19. Integrative modeling and novel particle swarm-based optimal design of wind farms

    Science.gov (United States)

    Chowdhury, Souma

    To meet the energy needs of the future, while seeking to decrease our carbon footprint, a greater penetration of sustainable energy resources such as wind energy is necessary. However, a consistent growth of wind energy (especially in the wake of unfortunate policy changes and reported under-performance of existing projects) calls for a paradigm shift in wind power generation technologies. This dissertation develops a comprehensive methodology to explore, analyze and define the interactions between the key elements of wind farm development, and establish the foundation for designing high-performing wind farms. The primary contribution of this research is the effective quantification of the complex combined influence of wind turbine features, turbine placement, farm-land configuration, nameplate capacity, and wind resource variations on the energy output of the wind farm. A new Particle Swarm Optimization (PSO) algorithm, uniquely capable of preserving population diversity while addressing discrete variables, is also developed to provide powerful solutions towards optimizing wind farm configurations. In conventional wind farm design, the major elements that influence the farm performance are often addressed individually. The failure to fully capture the critical interactions among these factors introduces important inaccuracies in the projected farm performance and leads to suboptimal wind farm planning. In this dissertation, we develop the Unrestricted Wind Farm Layout Optimization (UWFLO) methodology to model and optimize the performance of wind farms. The UWFLO method obviates traditional assumptions regarding (i) turbine placement, (ii) turbine-wind flow interactions, (iii) variation of wind conditions, and (iv) types of turbines (single/multiple) to be installed. The allowance of multiple turbines, which demands complex modeling, is rare in the existing literature. The UWFLO method also significantly advances the state of the art in wind farm optimization by

  20. An Integrated Multi-Criteria Decision Making Model for Evaluating Wind Farm Performance

    Directory of Open Access Journals (Sweden)

    Mei-Sung Kang

    2011-11-01

    Full Text Available The demands for alternative energy resources have been increasing exponentially in the 21st century due to continuous industrial development, depletion of fossil fuels and emerging environmental consciousness. Renewable energy sources, including wind energy, hydropower energy, geothermal energy, solar energy, biomass energy and ocean power, have received increasing attention as alternative means of meeting global energy demands. After Japan's Fukushima nuclear plant disaster in March 2011, more and more countries are having doubt about the safety of nuclear plants. As a result, safe and renewable energy sources are attracting even more attention these days. Wind energy production, with its relatively safer and positive environmental characteristics, has evolved in the past few decades from a marginal activity into a multi-billion dollar industry. In this research, a comprehensive evaluation model is constructed to select a suitable location for developing a wind farm. The model incorporates interpretive structural modeling (ISM, benefits, opportunities, costs and risks (BOCR and fuzzy analytic network process (FANP. Experts in the field are invited to contribute their expertise in evaluating the importance of the factors and various aspects of the wind farm evaluation problem, and the most suitable wind farm can finally be generated from the model. A case study is carried out in Taiwan in evaluating the expected performance of several potential wind farms, and a recommendation is provided for selecting the most appropriate wind farm for construction.

  1. Economics of compressed air energy storage to integrate wind power: A case study in ERCOT

    International Nuclear Information System (INIS)

    Compressed air energy storage (CAES) could be paired with a wind farm to provide firm, dispatchable baseload power, or serve as a peaking plant and capture upswings in electricity prices. We present a firm-level engineering-economic analysis of a wind/CAES system with a wind farm in central Texas, load in either Dallas or Houston, and a CAES plant whose location is profit-optimized. With 2008 hourly prices and load in Houston, the economically optimal CAES expander capacity is unrealistically large - 24 GW - and dispatches for only a few hours per week when prices are highest; a price cap and capacity payment likewise results in a large (17 GW) profit-maximizing CAES expander. Under all other scenarios considered the CAES plant is unprofitable. Using 2008 data, a baseload wind/CAES system is less profitable than a natural gas combined cycle (NGCC) plant at carbon prices less than $56/tCO2 ($15/MMBTU gas) to $230/tCO2 ($5/MMBTU gas). Entering regulation markets raises profit only slightly. Social benefits of CAES paired with wind include avoided construction of new generation capacity, improved air quality during peak times, and increased economic surplus, but may not outweigh the private cost of the CAES system nor justify a subsidy. - Research highlights: → Sizes of CAES and transmission paired with a Texas wind farm are optimized for profit. → A profit-maximizing wind farm owner would not invest in a dedicated CAES system. → The social benefit of a wind/CAES system is unlikely to outweigh private cost. → CAES cannot cost-effectively smooth wind power with plausible imminent carbon prices.

  2. Study on offshore wind farm integration mode and reactive power compensation

    Energy Technology Data Exchange (ETDEWEB)

    Bian, Xiaoyan; Hong, Lijun; Fu, Yang [Shanghai Univ. of Electrical Power (China). Power and Automation Engineering Dept.

    2013-07-01

    Two typical offshore wind farm grid-connected modes are introduced and dynamic characteristics under their modes are compared from the simulation by PSS/E. The result shows that offshore wind farm with VSC-HVDC has better dynamic characteristics on fault isolation, reactive power compensation, and fault ride through ability. In addition, STATCOM has been applied to the offshore wind farm, the simulation results indicates that it can improve the bus voltage stability in fault and maintain the voltage level under a small perturbation.

  3. The impact of traffic-flow patterns on air quality in urban street canyons.

    Science.gov (United States)

    Thaker, Prashant; Gokhale, Sharad

    2016-01-01

    We investigated the effect of different urban traffic-flow patterns on pollutant dispersion in different winds in a real asymmetric street canyon. Free-flow traffic causes more turbulence in the canyon facilitating more dispersion and a reduction in pedestrian level concentration. The comparison of with and without a vehicle-induced-turbulence revealed that when winds were perpendicular, the free-flow traffic reduced the concentration by 73% on the windward side with a minor increase of 17% on the leeward side, whereas for parallel winds, it reduced the concentration by 51% and 29%. The congested-flow traffic increased the concentrations on the leeward side by 47% when winds were perpendicular posing a higher risk to health, whereas reduced it by 17-42% for parallel winds. The urban air quality and public health can, therefore, be improved by improving the traffic-flow patterns in street canyons as vehicle-induced turbulence has been shown to contribute significantly to dispersion. PMID:26412198

  4. The impact of traffic-flow patterns on air quality in urban street canyons.

    Science.gov (United States)

    Thaker, Prashant; Gokhale, Sharad

    2016-01-01

    We investigated the effect of different urban traffic-flow patterns on pollutant dispersion in different winds in a real asymmetric street canyon. Free-flow traffic causes more turbulence in the canyon facilitating more dispersion and a reduction in pedestrian level concentration. The comparison of with and without a vehicle-induced-turbulence revealed that when winds were perpendicular, the free-flow traffic reduced the concentration by 73% on the windward side with a minor increase of 17% on the leeward side, whereas for parallel winds, it reduced the concentration by 51% and 29%. The congested-flow traffic increased the concentrations on the leeward side by 47% when winds were perpendicular posing a higher risk to health, whereas reduced it by 17-42% for parallel winds. The urban air quality and public health can, therefore, be improved by improving the traffic-flow patterns in street canyons as vehicle-induced turbulence has been shown to contribute significantly to dispersion.

  5. Integrated Method for Optimizing Connection Layout and Cable Selection for an Internal Network of a Wind Farm

    Directory of Open Access Journals (Sweden)

    Andrzej Wędzik

    2015-09-01

    Full Text Available An internal network of a wind farm is similar to a wide network structure. Wind turbines are deployed over a vast area, and cable lines used to interconnect them may have lengths reaching tens of kilometres. The cost of constructing such a network is a major component of the entire investment. Therefore, it is advisable to develop a configuration of such a farm’s internal connections which will minimise the cost, while complying with technical requirements even at the design stage. So far this has usually been done within two independent processes. At first the network structure ensuring the shortest possible connections between the turbines is determined. Then appropriate cables compliant with technical regulations are selected for the specified structure. But does this design approach ensure the optimal (lowest investment cost? This paper gives an answer to this question. A method for accomplishing the task given in the title is presented. Examples of calculations are presented and results are compared for the two methods of optimal wind farm internal connection structure design and cable cross-section dimensioning: two-stage and integrated. The usefulness of employing the Mixed Integer Nonlinear Programming (MNLP method in the process of determining the optimal structure of a wind farm’s cable network is demonstrated.

  6. Large-scale integration of off-shore wind power and regulation strategies of cogeneration plants in the Danish electricity system

    DEFF Research Database (Denmark)

    Østergaard, Poul Alberg

    2005-01-01

    The article analyses how the amount of a small-scale CHP plants and heat pumps and the regulation strategies of these affect the quantity of off-shore wind power that may be integrated into Danish electricity supply......The article analyses how the amount of a small-scale CHP plants and heat pumps and the regulation strategies of these affect the quantity of off-shore wind power that may be integrated into Danish electricity supply...

  7. Impacts of Large-scale Wind Power Grid Integration on Relay Protection and Countermeasures

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Several large-scale wind turbine tripping accidents occurred in Jiuquan wind power base in 2011. According to the on-site survey and analysis of these accidents related to relay protection, causes were found to be the collection system defects and low correct operation rate of small current grounded line selectors of the unearthed neutral point collection system. By referring to both the characteristics of Jiuquan wind power base and arrangement of relay protection, the short-circuit features of wind power and its impacts on relay protection are analyzed. The collection system and the retrofit of the small current grounded line selector are improved by specific countermeasures. Finally, further research subjects are put forward.

  8. Bell Canyon test summary report

    International Nuclear Information System (INIS)

    The Bell Canyon Test was an in situ evaluation of the ability of a cement grout plug to seal boreholes. It consisted of a 2-m-long, 20-cm-diameter grout plug in an anhydrite formation at a depth of 1370 m, directly above an aquifer that provided a 12.4 MPa (1800 psi) differential pressure. The aquifer had a production capability of 38,000 l/day (240 bbl/day, 104 gal/day). The observed leakage after plug installation was 0.6 l/day, which is equivalent to a 50 microdarcy flow path assuming all flow occurred through the plug cross-sectional area. Laboratory results and analysis of field data indicate that the bulk of the flow occurred through a microstructure at the interface between the plug and the host rock. The Bell Canyon Test demonstrated that a plug could be formulated, emplaced, and tested under actual conditions and provide acceptable performance. When these results are related to the WIPP performance assessment models, they provide additional confidence that borehole plugging can be accomplished satisfactorily. The Bell Canyon results can also be used as basis for future activities in the generic repository sealing program for similar emplacements and performance assessment evaluations. If the observed leakage rates are not acceptable at other sites, the BCT results would indicate that the first step in improving such emplacements should deal with improved bonding of the plug to the rock at these sites. The results obtained from the BCT, when coupled with results from long-term durability assessments, form a plug performance data basis for repository designers at other proposed waste repository sites

  9. ACCELERATED PILOT PROJECT FOR U CANYON DEMOLITION

    Energy Technology Data Exchange (ETDEWEB)

    KEHLER KL

    2011-01-13

    At the U.S. Department of Energy's Hanford Site in southeast Washington State, CH2M HILL Plateau Remediation Company (CH2M HILL) is underway on a first-of-a-kind project with the decommissioning and demolition of the U Canyon. Following the U.S. Environmental Protection Agency's Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) Record of Decision for the final remediation of the canyon, CH2M HILL is combining old and new technology and techniques to prepare U Canyon for demolition. The selected remedial action called first for consolidating and grouting equipment currently in the canyon into lower levels of the plant (openings called cells), after which the cell galleries, hot pipe trench, ventilation tunnel, drains and other voids below the operating deck and crane-way deck levels will be filled with approximately 20,000 cubic yards of grout and the canyon roof and walls demolished down to the approximate level of the canyon deck. The remaining canyon structure will then be buried beneath an engineered barrier designed to control potential contaminant migration for a 500-year life. Methods and lessons learned from this project will set the stage for the future demolition of Hanford's four other canyon-type processing facilities.

  10. Environmental assessment: Davis Canyon site, Utah

    Energy Technology Data Exchange (ETDEWEB)

    none,

    1986-05-01

    In February 1983, the US Department of Energy (DOE) identified the Davis Canyon site in Utah as one of the nine potentially acceptable sites for a mined geologic repository for spent nuclear fuel and high-level radioactive waste. To determine their suitability, the Davis Canyon site and the eight other potentially acceptable sites have been evaluated in accordance with the DOE's General Guidelines for the Recommendation of Sites for the Nuclear Waste Repositories. These evaluations were reported in draft environmental assessments (EAs), which were issued for public review and comment. After considering the comments received on the draft EAs, the DOE prepared the final EA. The Davis Canyon site is in the Paradox Basin, which is one of five distinct geohydrologic settings considering for the first repository. This setting contains one other potentially acceptable site -- the Lavender Canyon site. Although the Lavender Canyon site is suitable for site characterization, the DOE has concluded that the Davis Canyon site is the preferred site in the Paradox Basin. On the basis of the evaluations reported in this EA, the DOE has found that the Davis Canyon site is not disqualified under the guidelines. Furthermore, the DOE has found that the site is suitable for site characterization because the evidence does not support a conclusion that the site will not be able to meet each of the qualifying conditions specified in the guidelines. On the basis of these findings, the DOE is nominating the Davis Canyon site as one of five sites suitable for characterization.

  11. Environmental assessment: Davis Canyon site, Utah

    Energy Technology Data Exchange (ETDEWEB)

    none,

    1986-05-01

    In February 1983, the US Department of Energy (DOE) identified the Davis Canyon site in Utah as one of the nine potentially acceptable sites for a mined geologic repository for spent nuclear fuel and high- level radioactive waste. To determine their suitability, the Davis Canyon site and the eight other potentially acceptable sites have been evaluated in accordance with the DOE's General Guidelines for the Recommendation of Sites for the Nuclear Waste Repositories. These evaluations were reported in draft environmental assessments (EAs), which were issued for public review and comment. After considering the comments received on the draft EAs, the DOE prepared the final EA. The Davis Canyon site is in the Paradox Basin, which is one of five distinct geohydrologic settings considered for the first repository. This setting contains one other potentially acceptable site -- the Lavender Canyon site. Although the Lavender Canyon site is suitable for site characterization, the DOE has concluded that the Davis Canyon site is the preferred site in the Paradox Basin. On the basis of the evaluations reported in this EA, the DOE has found that the Davis Canyon site is not disqualified under the guidelines. Furthermore, the DOE has found that the site is suitable for site characterization because the evidence does not support a conclusion that the site will not be able to meet each of the qualifying conditions specified in the guidelines. On the basis of these findings, the DOE is nominating the Davis Canyon site as one of the five sites suitable for characterization.

  12. H-Canyon Recovery Crawler

    Energy Technology Data Exchange (ETDEWEB)

    Kriikku, E. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hera, K. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Marzolf, A. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Phillips, M. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-08-01

    The Nuclear Material Disposition Project group asked the Savannah River National Lab (SRNL) Research and Development Engineering (R&DE) department to help procure, test, and deploy a remote crawler to recover the 2014 Inspection Crawler (IC) that tipped over in the H-Canyon Air Exhaust Tunnel. R&DE wrote a Procurement Specification for a Recovery Crawler (RC) and SRNS Procurement Department awarded the contract to Power Equipment Manufacturing Inc. (PEM). The PEM RC was based on their standard sewer inspection crawler with custom arms and forks added to the front. The arms and forks would be used to upright the 2014 Inspection Crawler. PEM delivered the RC and associated cable reel, 2014 Inspection Crawler mockup, and manuals in late April 2015. R&DE and the team tested the crawler in May of 2015 and made modifications based on test results and Savannah River Site (SRS) requirements. R&DE delivered the RC to H-Area at the end of May. The team deployed the RC on June 9, 10, and 11, 2015 in the H-Canyon Air Exhaust Tunnel. The RC struggled with some obstacles in the tunnel, but eventually made it to the IC. The team spent approximately five hours working to upright the IC and eventually got it on its wheels. The IC travelled approximately 20 feet and struggled to drive over debris on the air tunnel floor. Unfortunately the IC tripped over trying to pass this obstacle. The team decided to leave the IC in this location and inspect the tunnel with the RC. The RC passed the IC and inspected the tunnel as it travelled toward H-Canyon. The team turned the RC around when it was about 20 feet from the H-Canyon crossover tunnel. From that point, the team drove the RC past the manway towards the new sand filter and stopped approximately 20 feet from the new sand filter. The team removed the RC from the tunnel, decontaminated the RC, and stored it the manway building, 294-2H. The RC deployment confirmed the IC was not in a condition to perform useful tunnel inspections and

  13. Primary Initiation of Submarine Canyons

    CERN Document Server

    Herndon, J Marvin

    2011-01-01

    The discovery of close-to-star gas-giant exo-planets lends support to the idea of Earth's origin as a Jupiter-like gas-giant and to the consequences of its compression, including whole-Earth decompression dynamics that gives rise, without requiring mantle convection, to the myriad measurements and observations whose descriptions are attributed to plate tectonics. I propose here another, unanticipated consequence of whole-Earth decompression dynamics: namely, a specific, dominant, non-erosion, underlying initiation-mechanism precursor for submarine canyons that follows as a direct consequence of Earth's early origin as a Jupiter-like gas-giant.

  14. Effects of building roof greening on air quality in street canyons

    Science.gov (United States)

    Baik, Jong-Jin; Kwak, Kyung-Hwan; Park, Seung-Bu; Ryu, Young-Hee

    2012-12-01

    Building roof greening is a successful strategy for improving urban thermal environment. It is of theoretical interest and practical importance to study the effects of building roof greening on urban air quality in a systematic and quantitative way. In this study, we examine the effects of building roof greening on air quality in street canyons using a computational fluid dynamics (CFD) model that includes the thermodynamic energy equation and the transport equation of passive, non-reactive pollutants. For simplicity, building roof greening is represented by specified cooling. Results for a simple building configuration with a street canyon aspect ratio of one show that the cool air produced due to building roof greening flows into the street canyon, giving rise to strengthened street canyon flow. The strengthened street canyon flow enhances pollutant dispersion near the road, which decreases pollutant concentration there. Thus, building roof greening improves air quality near the road. The degree of air quality improvement near the road increases as the cooling intensity increases. In the middle region of the street canyon, the air quality can worsen when the cooling intensity is not too strong. Results for a real urban morphology also show that building roof greening improves air quality near roads. The degree of air quality improvement near roads due to building roof greening depends on the ambient wind direction. These findings provide a theoretical foundation for constructing green roofs for the purpose of improving air quality near roads or at a pedestrian level as well as urban thermal environment. Further studies using a CFD model coupled with a photochemistry model and a surface energy balance model are required to evaluate the effects of building roof greening on air quality in street canyons in a more realistic framework.

  15. An experimental approach to submarine canyon evolution

    Science.gov (United States)

    Lai, Steven Y. J.; Gerber, Thomas P.; Amblas, David

    2016-03-01

    We present results from a sandbox experiment designed to investigate how sediment gravity flows form and shape submarine canyons. In the experiment, unconfined saline gravity flows were released onto an inclined sand bed bounded on the downstream end by a movable floor that was used to increase relief during the experiment. In areas unaffected by the flows, we observed featureless, angle-of-repose submarine slopes formed by retrogressive breaching processes. In contrast, areas influenced by gravity flows cascading across the shelf break were deeply incised by submarine canyons with well-developed channel networks. Normalized canyon long profiles extracted from successive high-resolution digital elevation models collapse to a single profile when referenced to the migrating shelf-slope break, indicating self-similar growth in the relief defined by the canyon and intercanyon profiles. Although our experimental approach is simple, the resulting canyon morphology and behavior appear similar in several important respects to that observed in the field.

  16. The Mirror and the Canyon: Reflected Images, Echoed Voices How Evidence of GW's Performing Arts Integration Model Is Used to Build Support for Arts Education Integration and to Promote Sustainability

    Science.gov (United States)

    Ellrodt, John Charles; Fico, Maria; Harnett, Susanne; Ramsey, Lori Gerstein; Lopez, Angelina

    2014-01-01

    The Global Writes (GW) model is a well-designed performing arts integrated literacy program that builds local and global support among students, teachers, and arts partners through the use of innovative technologies. Through local partnerships between schools and arts organizations forged by GW, classroom teachers and local teaching artists build…

  17. Eastern Renewable Generation Integration Study: Flexibility and High Penetrations of Wind and Solar; NREL (National Renewable Energy Laboratory)

    Energy Technology Data Exchange (ETDEWEB)

    Bloom, Aaron; Townsend, Aaron; Palchak, David

    2015-07-29

    Balancing wind and solar in a model is relatively easy. All you need to do is assume a very large system with infinite flexibility! But what if you don't have an infinitely flexible system? What if there are thousands of generators nestled in a handful of regions that are unlikely to change their operational practices? Would you still have enough flexibility to balance hundreds of gigawatts of wind and solar at a 5 minute level? At NREL, we think we can, and our industry partners agree. This presentation was presented at the IEEE Power and Energy Society General Meeting by Aaron Bloom, highlighting results of the Eastern Renewable Generation Integration Study.

  18. Integrating wind and solar power into the energy systems of the 21st century

    Energy Technology Data Exchange (ETDEWEB)

    Flavin, C. [Worldwatch Inst., Washington, DC (United States)

    1995-12-31

    Although they have been pursued by scientists and entrepreneurs for two decades, solar and wind energy have not yet claimed the large share of the world energy market that proponents hoped they would. Yet the past two years brought a series of developments that suggest the time has come for solar and wind energy to compete directly with fossil fuels. Wind and solar power generators are likely to contribute significant power to the electricity systems of scores of countries within the next decade, with generating costs as low as 4-5 cents per kilowatt-hour. This will require adjustment in the operation of power transmission and distribution systems to accommodate intermittent resources, as well as new time-specific pricing of electricity. The transition to more open, competitive power systems, with liberal access by independent producers, is likely to speed introduction of the new technologies. Altogether, the energy that strikes the earth`s atmosphere in the form of sunlight each year, and the winds that flow from it, represent the equivalent of nearly 1,000 trillion barrels of oil-sufficient to fuel the global economy thousands of times over. By relying on a new generation of efficient, high-tech, and mass produced energy conversion devices such as advanced wind turbines and photovoltaics, the world can rapidly reduce its dependence on oil and coal in the twenty-first century. In the more distant future, solar and wind energy have the potential not only to supply much of the world`s electricity but to displace the direct use of oil and natural gas. Solar and wind energy can be used to split water via electrolysis, producing hydrogen gas that can be substituted for liquid and gaseous fuels. (46 refs.)

  19. 2008 Weather and Aeolian Sand-Transport Data from the Colorado River Corridor, Grand Canyon, Arizona

    Science.gov (United States)

    Draut, Amy E.; Sondossi, Hoda A.; Hazel, Joseph E., Jr.; Andrews, Timothy; Fairley, Helen C.; Brown, Christopher R.; Vanaman, Karen M.

    2009-01-01

    This report presents measurements of weather parameters and aeolian (windblown) sand transport made in 2008 near selected archaeological sites in the Colorado River corridor through Grand Canyon, Ariz. The quantitative methods and data discussed here form a basis for monitoring ecosystem processes that affect archeological-site stability. Combined with forthcoming work to evaluate landscape evolution at nearby archaeological sites, these data can be used to document the relationship between physical processes, including weather and aeolian sand transport, and their effects on the physical integrity of archaeological sites. Data collected in 2008 reveal event- and seasonal-scale variations in rainfall, wind, temperature, humidity, and barometric pressure. Broad seasonal changes in aeolian sediment flux are also apparent at most study sites. The continuation of monitoring that began in 2007, and installation of equipment at several new sites in early 2008, allowed evaluation of the effects of the March 2008 high-flow experiment (HFE) on aeolian sand transport. At two of the nine sites studied, spring and summer winds reworked 2008 HFE sandbars to form new aeolian dunes, at which sand moved inland toward larger, well-established dune fields. At the other seven study sites, neither dune formation nor enhanced sand transport after the HFE were observed. At several of those sites, dominant wind directions in spring 2008 were not oriented such that much HFE sand would have moved inland; at other sites, lack of increased inland sand flux is attributable to lack of sandbar enlargement near the study sites or to inhibition of sand movement by vegetation or local topography.

  20. Large-scale integration of optimal combinations of PV, wind and wave power into the electricity supply

    DEFF Research Database (Denmark)

    Lund, Henrik

    2006-01-01

    This article presents the results of analyses of large-scale integration of wind power, photo voltaic (PV) and wave power into a Danish reference energy system. The possibility of integrating Renewable Energy Sources (RES) into the electricity supply is expressed in terms of the ability to avoid...... ancillary services are needed in order to secure the electricity supply system. The idea is to benefit from the different patterns in the fluctuations of different renewable sources. And the purpose is to identify optimal mixtures from a technical point of view. The optimal mixture seems to be when onshore...... the total input is above 80% of demand, PV should cover 20% and wave power 30%. Meanwhile the combination of different sources is alone far from a solution to large-scale integration of fluctuating resources. This measure is to be seen in combination with other measures such as investment in flexible energy...

  1. A review of the role of submarine canyons in deep-ocean exchange with the shelf

    Directory of Open Access Journals (Sweden)

    S. E. Allen

    2009-12-01

    Full Text Available Cross shelf-break exchange is limited by the tendency of geostrophic flow to follow bathymetric contours, not cross them. However, small scale topography, such as canyons, can reduce the local lengthscale of the flow and increase the local Rossby number. These higher Rossby numbers mean the flow is no longer purely geostrophic and significant cross-isobath flow can occur. This cross-isobath flow includes both upwelling and downwelling due to wind-driven shelf currents and the strong cascading flows of dense shelf-water into the ocean. Tidal currents usually run primarily parallel to the shelf-break topography. Canyons cut across these flows and thus are often regions of generation of strong baroclinic tides and internal waves. Canyons can also focus internal waves. Both processes lead to greatly elevated levels of mixing. Thus, through both advection and mixing processes, canyons can enhance Deep Ocean Shelf Exchange. Here we review the state of the science describing the dynamics of the flows and suggest further areas of research, particularly into quantifying fluxes of nutrients and carbon as well as heat and salt through canyons.

  2. Numerical Study of Traffic Pollutant Dispersion within Different Street Canyon Configurations

    Directory of Open Access Journals (Sweden)

    Yucong Miao

    2014-01-01

    Full Text Available The objective of this study is to numerically study flow and traffic exhaust dispersion in urban street canyons with different configurations to find out the urban-planning strategies to ease the air pollution. The Computational Fluid Dynamics (CFD model used in this study—Open Source Field Operation and Manipulation (OpenFOAM software package—was firstly validated against the wind-tunnel experiment data by using three different k-ε turbulence models. And then the patterns of flow and dispersion within three different kinds of street canyon configuration under the perpendicular approaching flow were numerically studied. The result showed that the width and height of building can dramatically affect the pollution level inside the street canyon. As the width or height of building increases, the pollution at the pedestrian level increases. And the asymmetric configuration (step-up or step-down street canyon could provide better ventilation. It is recommended to design a street canyon with nonuniform configurations. And the OpenFOAM software package can be used as a reliable tool to study flows and dispersions around buildings.

  3. Fluid mechanical dispersion of airborne pollutants inside urban street canyons subjecting to multi-component ventilation and unstable thermal stratifications.

    Science.gov (United States)

    Mei, Shuo-Jun; Liu, Cheng-Wei; Liu, Di; Zhao, Fu-Yun; Wang, Han-Qing; Li, Xiao-Hong

    2016-09-15

    The pedestrian level pollutant transport in street canyons with multiple aspect ratios (H/W) is numerically investigated in the present work, regarding of various unstable thermal stratification scenarios and plain surrounding. Non-isothermal turbulent wind flow, temperature field and pollutant spread within and above the street canyons are solved by the realizable k-ε turbulence model along with the enhanced wall treatment. One-vortex flow regime is observed for shallow canyons with H/W=0.5, whereas multi-vortex flow regime is observed for deep canyons with H/W=2.0. Both one-vortex and multi-vortex regimes could be observed for the street canyons with H/W=1.0, where the secondary vortex could be initiated by the flow separation and intensified by unstable thermal stratification. Air exchange rate (AER) and pollutant retention time are adopted to respectively evaluate the street canyon ventilation and pollutant removal performance. A second-order polynomial functional relationship is established between AER and Richardson number (Ri). Similar functional relationship could be established between retention time and Ri, and it is only valid for canyons with one-vortex flow regime. In addition, retention time could be prolonged abruptly for canyons with multi-vortex flow regime. Very weak secondary vortex is presented at the ground level of deep canyons with mild stratification, where pollutants are highly accumulated. However, with the decrease of Ri, pollutant concentration adjacent to the ground reduces accordingly. Present research could be applied to guide the urban design and city planning for enhancing pedestrian environment. PMID:27262984

  4. Analytical Method for Estimating Energy Output of Small Wind Turbines Integrated in Urban Areas

    Directory of Open Access Journals (Sweden)

    Popovac M.

    2012-10-01

    Full Text Available This paper presents the development of the analytical approach for estimating the wind energy potential at locations around buildings in urban areas that are suitable for installing Small Wind Turbines (SWT. This development is performed in three steps. In order to analyze the flow pattern in a typical urban geometry, the first step consisted of a series of numerical simulations, where an assumed urban configuration (specified building size and respective distances between the buildings was varied with an incremental value, and for each analyzed configuration different incoming wind conditions (different reference wind velocity were incrementally imposed. In the second step the velocity profiles in the characteristic cutlines around the central building under investigation were extracted from the respective realizations of urban flow numerical solutions, and an analytical expression was derived approximating all extracted velocity profiles to fit the best an assumed flow pattern. The derived analytical expression was cross-plotted with the results of a fully three-dimensional realistic urban flow numerical solution, and the obtained matching level was satisfactory. Finally, using the derived expression, in the third step the estimation of SWT energy output was defined based on the average wind velocity information at given location and the related urban configuration characteristics.

  5. LPV control for the full region operation of a wind turbine integrated with synchronous generator.

    Science.gov (United States)

    Cao, Guoyan; Grigoriadis, Karolos M; Nyanteh, Yaw D

    2015-01-01

    Wind turbine conversion systems require feedback control to achieve reliable wind turbine operation and stable current supply. A robust linear parameter varying (LPV) controller is proposed to reduce the structural loads and improve the power extraction of a horizontal axis wind turbine operating in both the partial load and the full load regions. The LPV model is derived from the wind turbine state space models extracted by FAST (fatigue, aerodynamics, structural, and turbulence) code linearization at different operating points. In order to assure a smooth transition between the two regions, appropriate frequency-dependent varying scaling parametric weighting functions are designed in the LPV control structure. The solution of a set of linear matrix inequalities (LMIs) leads to the LPV controller. A synchronous generator model is connected with the closed LPV control loop for examining the electrical subsystem performance obtained by an inner speed control loop. Simulation results of a 1.5 MW horizontal axis wind turbine model on the FAST platform illustrates the benefit of the LPV control and demonstrates the advantages of this proposed LPV controller, when compared with a traditional gain scheduling PI control and prior LPV control configurations. Enhanced structural load mitigation, improved power extraction, and good current performance were obtained from the proposed LPV control. PMID:25884036

  6. LPV Control for the Full Region Operation of a Wind Turbine Integrated with Synchronous Generator

    Directory of Open Access Journals (Sweden)

    Guoyan Cao

    2015-01-01

    Full Text Available Wind turbine conversion systems require feedback control to achieve reliable wind turbine operation and stable current supply. A robust linear parameter varying (LPV controller is proposed to reduce the structural loads and improve the power extraction of a horizontal axis wind turbine operating in both the partial load and the full load regions. The LPV model is derived from the wind turbine state space models extracted by FAST (fatigue, aerodynamics, structural, and turbulence code linearization at different operating points. In order to assure a smooth transition between the two regions, appropriate frequency-dependent varying scaling parametric weighting functions are designed in the LPV control structure. The solution of a set of linear matrix inequalities (LMIs leads to the LPV controller. A synchronous generator model is connected with the closed LPV control loop for examining the electrical subsystem performance obtained by an inner speed control loop. Simulation results of a 1.5 MW horizontal axis wind turbine model on the FAST platform illustrates the benefit of the LPV control and demonstrates the advantages of this proposed LPV controller, when compared with a traditional gain scheduling PI control and prior LPV control configurations. Enhanced structural load mitigation, improved power extraction, and good current performance were obtained from the proposed LPV control.

  7. Prehistoric deforestation at Chaco Canyon?

    Science.gov (United States)

    Wills, W H; Drake, Brandon L; Dorshow, Wetherbee B

    2014-08-12

    Ancient societies are often used to illustrate the potential problems stemming from unsustainable land-use practices because the past seems rife with examples of sociopolitical "collapse" associated with the exhaustion of finite resources. Just as frequently, and typically in response to such presentations, archaeologists and other specialists caution against seeking simple cause-and effect-relationships in the complex data that comprise the archaeological record. In this study we examine the famous case of Chaco Canyon, New Mexico, during the Bonito Phase (ca. AD 860-1140), which has become a prominent popular illustration of ecological and social catastrophe attributed to deforestation. We conclude that there is no substantive evidence for deforestation at Chaco and no obvious indications that the depopulation of the canyon in the 13th century was caused by any specific cultural practices or natural events. Clearly there was a reason why these farming people eventually moved elsewhere, but the archaeological record has not yet produced compelling empirical evidence for what that reason might have been. Until such evidence appears, the legacy of Ancestral Pueblo society in Chaco should not be used as a cautionary story about socioeconomic failures in the modern world.

  8. Probabilistic Constrained Load Flow Considering Integration of Wind Power Generation and Electric Vehicles

    DEFF Research Database (Denmark)

    Vlachogiannis, Ioannis (John)

    2009-01-01

    A new formulation and solution of probabilistic constrained load flow (PCLF) problem suitable for modern power systems with wind power generation and electric vehicles (EV) demand or supply is represented. The developed stochastic model of EV demand/supply and the wind power generation model...... are incorporated into load flow studies. In the resulted PCLF formulation, discrete and continuous control parameters are engaged. Therefore, a hybrid learning automata system (HLAS) is developed to find the optimal offline control settings over a whole planning period of power system. The process of HLAS...... is applied to a new introduced 14-busbar test system which comprises two wind turbine (WT) generators, one small power plant, and two EV-plug-in stations connected at two PQ buses. The results demonstrate the excellent performance of the HLAS for PCLF problem. New formulae to facilitate the optimal...

  9. Effect of Physical Constraints on Load Frequency Control of Deregulated Hybrid Power System Integrated with DFIG Wind Turbine

    Directory of Open Access Journals (Sweden)

    Aditi Gupta

    2014-12-01

    Full Text Available This paper presents a generalized model for load frequency control (LFC design in a hybrid multi-area deregulated power system including physical constraints. Renewable energy source named doubly fed induction generator (DFIG based wind energy source is integrated into the system that provides the modified emulating inertial control and reduces the deviations in frequency and tie-line power, following a transient load perturbation. In addition to this, the three basic physical constraints viz. generation rate constraints (GRC, speed governor dead band and communication or time delay have been imposed on the power system that affect the system’s security, reliability and integrity. To get the better performance of the various controllers in power system, their gains are optimized using integral square error (ISE technique. Present simulation studies reveal that the system’s performance becomes better by the inclusion of DFIG based wind turbine. It is also shown that the dynamic performance of the system becomes poorer by adding physical constraints but it is a more realistic approach.

  10. Multiobjective Optimization in Combinatorial Wind Farms System Integration and Resistive SFCL Using Analytical Hierarchy Process

    DEFF Research Database (Denmark)

    Moghadasi, Amirhasan; Sarwat, Arif; Guerrero, Josep M.

    2016-01-01

    This paper presents a positive approach for low voltage ride-through (LVRT) improvement of the permanent magnet synchronous generator (PMSG) based on a large wind power plant (WPP) of 50MW. The proposed method utilizes the conventional current control strategy to provide a reactive power requirem......This paper presents a positive approach for low voltage ride-through (LVRT) improvement of the permanent magnet synchronous generator (PMSG) based on a large wind power plant (WPP) of 50MW. The proposed method utilizes the conventional current control strategy to provide a reactive power...

  11. Street canyon ventilation control by proper planning and development

    Directory of Open Access Journals (Sweden)

    Balakin Vladimir Vasil'evich

    2014-05-01

    Full Text Available The objective of street canyon ventilation control in major streets is a tool of air pollution prevention in them, protection of housing areas from excessive wind or preservation and intensification of existing wind speed in case of insufficient ventilation. The maximum permissible concentration of car exhaust pollutants with wind speed within comfortable and permissible values by physiological and hygienic criteria, are ensured as from 40 to 70 % of thoroughfares in major cities. The dependence of air pollution level on wind speed is comparable to its dependence on traffic intensity and ratio of buildings height (H to street width. But one has to take into account that, if the wind blows across the street, vortices form within the street canyon, which results in higher concentration of car exhaust pollutants near the downwind buildings. The objective of this work is to find the functional dependences of wind speed in a major street on its width and density of buildings, and also to find out which street configurations are favorable for formation of closed air circulation within it, resulting in insufficient aeration. The experimental research was done on a site for large-scale modeling of built-up urban territory, using cup anemometers. The coefficients of dependence of wind speed within a street on the types of buildings and on the street width were obtained. Characteristics of street layouts for control of aeration were determined. Building density rates for maximizing or optimizing the wind speed were determined. Street layouts are considered where stable vortices form between the buildings. For example, vortices within the street canyon’s cross-section appear when buildings squarish in ground plan situated far apart are replaced by oblong ones with the minimum allowed intervals of 15 meters between them (for 5-storeyed buildings; or intervals equal to the buildings’ height, or where the buildings are long and close together. With

  12. Local Mass Transfer Coefficient for Idealized 2D Urban Street Canyon Models

    Science.gov (United States)

    Leung, Ka Kit; Liu, Chun-Ho

    2011-09-01

    Human activities in urban areas is one of the major sources of anthropogenic releases in the atmospheric boundary layer (ABL). The mechanism of urban morphology for the heat and mass transfer in built environment is thus an attractive topic in the research community. In this paper, a series of laboratory measurements is conducted to elucidate the mass transfer from hypothetical urban roughness constructed by idealized 2D street canyons. The experiments are carried out in the wind tunnel in the University of Hong Kong. The urban ABL structure inside the wind tunnel is controlled by placing small cubic Styrofoam blocks upstream of the test section. The street canyons are fabricated by movable rectangular acrylic blocks so that different building height to street width (aspect) ratios are examined. The height of building blocks is kept minimum to make sure that the urban ABL over the street canyons is high enough for fully developed turbulent flows. The prevailing wind is normal to the street axis, demonstrating the scenario of least pollutant removal from the street canyons to the urban ABL. The sample street canyon is covered by soaked filter papers to represent uniform mass concentrations on the building facades and ground surface. The wet bulb temperature of the filter papers is continuously monitored to ensure saturated conditions. Their weight before and after an experiment is used to measure the amount of water evaporated. Preliminary results illustrate the local mass transfer coefficient distribution for aspect ratios 1/4, 1/2, 1, and 2, which are comparable with those available in literuatre.

  13. Modeling and resonance issues of wind farm integration with related facts applications

    Science.gov (United States)

    Auddy, Soubhik

    This thesis deals with electromechanical oscillations, torsional oscillations and resonance issues in power systems fed by conventional steam-turbine generators and emerging wind turbine generators. Solutions to several of these problems are proposed using Flexible AC Transmission Systems (FACTS) Controllers. Inter-area oscillations are investigated in the IEEE 39 bus system and are damped by a novel Static VAR Compensator (SVC) control signal utilizing a weighted sum of remote generator speeds derived from bus voltage angles. The weights are calculated from participation factor analysis using commercial software Dynamic Security Assessment (DSA) Power Tools and are validated by EMTDC/PSCAD simulations. Subsynchronous resonance (SSR) in steam-turbine generators has been traditionally damped with SVC using either local signals or signals derived from a combination of local signals. This thesis proposes a novel SVC controller based on remote generator speed for alleviating SSR. This controller is shown from EMTDC/PSCAD simulations to be much more effective than the previously reported controllers for the IEEE First SSR Benchmark system. The efficacy is demonstrated for all the four critical series compensation levels. With the worldwide growth of renewable energy, large wind farms are likely to be connected to series compensated networks for evacuation of bulk power. This may lead to the potential of SSR in the wind turbine generators. For the first time, a detailed electromagnetic transient study using EMTDC/PSCAD has been conducted in this thesis to demonstrate that subsynchronous resonance can be a cause of concern in series compensated wind farms at realistic levels of power flow and series compensation levels. Novel controllers for two FACTS devices - a Static VAR Compensator (SVC) and a Thyristor Controlled Series Capacitor (TCSC) - are proposed to mitigate SSR under all realistic compensation levels in a modified IEEE First Benchmark system. It is further

  14. Internal waves in the Petacalco canyon, Mexico

    Science.gov (United States)

    Ruiz-Angulo, Angel; Zavala-Hidalgo, Jorge

    2012-11-01

    On the Mexican coastline, specifically on the Pacific side, there are many submarine canyons. One of the key rolls of coastal submarine canyons is that deep water from adjacent oceanic regions is brought up to the shelf with lots of nutrients enhancing primary production. The head of the Petacalco canyon is located in the Petacalco Bay, in the Pacific Ocean (ca. 17.5N and 102W). During, previous CTD surveys in the area, strong upwelling has been noticed, based on those observations a later survey was designed covering the Petacalco canyon with much larger spatial resolution. Along with those measurements, two thermistor arrays were deployed on the SW crest of the canyon at depths of approximately 60 [m]. The observations, from the thermistor arrays, show large temporal temperature variations with a semi-diurnal frequency. Those variations suggest the presence of internal waves traveling along the canyon axis, if the incidence angle of the internal wave matches the topographic slope results on breaking of internal waves enhancing mixing. This condition occurs at several locations along the canyon axis producing enough mixing of deep oceanic waters with continental waters, increasing the abundance of nutrients in the surrounding region.

  15. Flow dynamics around downwelling submarine canyons

    Directory of Open Access Journals (Sweden)

    J. M. Spurgin

    2014-05-01

    Full Text Available Flow dynamics around a downwelling submarine canyon were analysed with the Massachusetts Institute of Technology general circulation model. Blanes Canyon (Northwest Mediterranean was used for topographic and initial forcing conditions. Fourteen scenarios were modelled with varying forcing conditions. Rossby number and Burger number were used to determine the significance of Coriolis acceleration and stratification (respectively and their impacts on flow dynamics. A new non-dimensional parameter (χ was introduced to determine the significance of vertical variations in stratification. Some simulations do see brief periods of upwards displacement of water during the 10 day model period, however, the presence of the submarine canyon is found to enhance downwards advection of density in all model scenarios. High Burger numbers lead to negative vorticity and a trapped anticyclonic eddy within the canyon, as well as an increased density anomaly. Low Burger numbers lead to positive vorticity, cyclonic circulation and weaker density anomalies. Vertical variations in stratification affect zonal jet placement. Under the same forcing conditions, the zonal jet is pushed offshore in more uniformly stratified domains. Offshore jet location generates upwards density advection away from the canyon, while onshore jets generate downwards density advection everywhere within the model domain. Increasing Rossby values across the canyon axis, as well as decreasing Burger values, increase negative vertical flux at shelf break depth (150 m. Increasing Rossby numbers lead to stronger downwards advection of a passive tracer (nitrate as well as stronger vorticity within the canyon. Results from previous studies were explained within this new dynamic framework.

  16. Flow dynamics around downwelling submarine canyons

    Directory of Open Access Journals (Sweden)

    J. M. Spurgin

    2014-10-01

    Full Text Available Flow dynamics around a downwelling submarine canyon were analysed with the Massachusetts Institute of Technology general circulation model. Blanes Canyon (northwestern Mediterranean was used for topographic and initial forcing conditions. Fourteen scenarios were modelled with varying forcing conditions. Rossby and Burger numbers were used to determine the significance of Coriolis acceleration and stratification (respectively and their impacts on flow dynamics. A new non-dimensional parameter (χ was introduced to determine the significance of vertical variations in stratification. Some simulations do see brief periods of upwards displacement of water during the 10-day model period; however, the presence of the submarine canyon is found to enhance downwards advection of density in all model scenarios. High Burger numbers lead to negative vorticity and a trapped anticyclonic eddy within the canyon, as well as an increased density anomaly. Low Burger numbers lead to positive vorticity, cyclonic circulation, and weaker density anomalies. Vertical variations in stratification affect zonal jet placement. Under the same forcing conditions, the zonal jet is pushed offshore in more uniformly stratified domains. The offshore jet location generates upwards density advection away from the canyon, while onshore jets generate downwards density advection everywhere within the model domain. Increasing Rossby values across the canyon axis, as well as decreasing Burger values, increase negative vertical flux at shelf break depth (150 m. Increasing Rossby numbers lead to stronger downwards advection of a passive tracer (nitrate, as well as stronger vorticity within the canyon. Results from previous studies are explained within this new dynamic framework.

  17. Guest Editorial Special Issue on Security and Protection of Wind Power Grid Integration

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Wind power is one of the key renewable energy to solve the world's energy shortage and achieve a low-carbon society. It can contribute to resolving the primary energy supply, improving the energy structure, preventing the environment, achieving the harmonious society and sustainable developmentof electric power industry.

  18. New tool for integration of wind power forecasting into power system operation

    DEFF Research Database (Denmark)

    Gubina, Andrej F.; Keane, Andrew; Meibom, Peter;

    2009-01-01

    The paper describes the methodology that has been developed for transmission system operators (TSOs) of Republic of Ireland, Eirgrid, and Northern Ireland, SONI the TSO in Northern Ireland, to study the effects of advanced wind power forecasting on optimal short-term power system scheduling. The ...

  19. Integration of Wave and Offshore Wind Energy in a European Offshore Grid

    DEFF Research Database (Denmark)

    Chozas, Julia Fernandez; Sørensen, H. C.; Korpås, M.

    2010-01-01

    of offshore renewable energy sources. According to this, the paper covers i) public and private initiatives for offshore transmission networks, ii) the synergies between the wave and the offshore wind energy sector within an offshore grid, iii) power transmission options for offshore generation and iv...

  20. Multi-objective Generation Expansion Planning for Integrating Largescale Wind Generation

    DEFF Research Database (Denmark)

    Zhang, Chunyu; Ding, Yi; Kang, Chongqing

    2013-01-01

    Due to the growth of energy consumption, the extensive use of conventional fossil fuels from the exhaustible resources and the environmental concerns, high penetration of renewable energy resources is considerably observed worldwide. Wind power generation is holding the first rank in terms of uti...

  1. Integral-Field Spectroscopy of the Post Red Supergiant IRC +10420: evidence for an axi-symmetric wind

    CERN Document Server

    Davies, Ben; Sahu, Kailash C

    2007-01-01

    We present NAOMI/OASIS adaptive-optics assisted integral-field spectroscopy of the transitional massive hypergiant IRC +10420, an extreme mass-losing star apparently in the process of evolving from a Red Supergiant toward the Wolf-Rayet phase. To investigate the present-day mass-loss geometry of the star, we study the appearance of the line-emission from the inner wind as viewed when reflected off the surrounding nebula. We find that, contrary to previous work, there is strong evidence for wind axi-symmetry, based on the equivalent-width and velocity variations of H$\\alpha$ and Fe {\\sc ii} $\\lambda$6516. We attribute this behaviour to the appearance of the complex line-profiles when viewed from different angles. We also speculate that the Ti {\\sc ii} emission originates in the outer nebula in a region analogous to the Strontium Filament of $\\eta$ Carinae, based on the morphology of the line-emission. Finally, we suggest that the present-day axisymmetric wind of IRC +10420, combined with its continued blueward...

  2. A field evaluation of remote sensor measurements of wind, temperature, and moisture for ARM integrated sounding system research

    Energy Technology Data Exchange (ETDEWEB)

    Martner, B.E.; Westwater, E.R.; Strauch, R.G. [and others

    1993-10-01

    Remote sensing systems were operated in Colorado in February and March 1991 to obtain detailed profiles of the kinematic and thermodynamic structure of the atmosphere for the US Department of Energy`s Atmospheric Radiation Measurement (ARM) research program. The instruments included wind profilers, Radio Acoustic Sounding Systems (PASS), microwave and infrared radiometers, an infrared spectrometer, ceilometers, radiosondes, surface meteorological stations, and other equipment. A mesoscale data assimilation model will be used to combine the data into dynamically consistent four-dimensional fields as part of an integrated data assimilation sounding system. This report evaluates the performance of the NOAA remote sensors used in the 1991 field data collection. These included five different wind profilers, each equipped with RASS capability for temperature profiling, and microwave radiometers for measurements of pathintegrated water vapor and liquid water content. The design and initial testing of a Fourier-transform InfraRed Sounder (FIRS) for humidity profiling is also described. The ranges of height coverage and measurement accuracies for each wind profiler/RASS are examined. Specific recommendations for optimizing the design and configuration of similar instruments are made for the ARM cloud and Radiation Testbed (CART) sites, based on results of the 1991 field work and earlier tests. Examples of routine processed data products are presented for three intensive operating period studies to further illustrate the remote sensors` capabilities.

  3. Influence of roadside hedgerows on air quality in urban street canyons

    Science.gov (United States)

    Gromke, Christof; Jamarkattel, Nabaraj; Ruck, Bodo

    2016-08-01

    Understanding pollutant dispersion in the urban environment is an important aspect of providing solutions to reduce personal exposure to vehicle emissions. To this end, the dispersion of gaseous traffic pollutants in urban street canyons with roadside hedges was investigated. The study was performed in an atmospheric boundary layer wind tunnel using a reduced-scale (M = 1:150) canyon model with a street-width-to-building-height ratio of W/H = 2 and a street-length-to-building-height ratio of L/H = 10. Various hedge configurations of differing height, permeability and longitudinal segmentation (continuous over street length L or discontinuous with clearings) were investigated. Two arrangements were examined: (i) two eccentric hedgerows sidewise of the main traffic lanes and (ii) one central hedgerow between the main traffic lanes. In addition, selected configurations of low boundary walls, i.e. solid barriers, were examined. For a perpendicular approach wind and in the presence of continuous hedgerows, improvements in air quality in the center area of the street canyon were found in comparison to the hedge-free reference scenario. The pollutant reductions were greater for the central hedge arrangements than for the sidewise arrangements. Area-averaged reductions between 46 and 61% were observed at pedestrian head height level on the leeward side in front of the building for the centrally arranged hedges and between 18 and 39% for the two hedges arranged sidewise. Corresponding area-averaged reductions ranging from 39 to 55% and from 1 to 20% were found at the bottom of the building facades on the leeward side. Improvements were also found in the areas at the lateral canyon ends next to the crossings for the central hedge arrangements. For the sidewise arrangements, increases in traffic pollutants were generally observed. However, since the concentrations in the end areas were considerably lower compared to those in the center area, an overall improvement remained

  4. Grid Integration of Offshore Wind Farms via VSC-HVDC – Dynamic Stability Study

    DEFF Research Database (Denmark)

    Liu, Hongzhi

    such as voltage and frequency control. The greater distance to shore makes commonly used high voltage AC (HVAC) connection unsuitable economically and technically for large offshore wind farms. Alternatively, voltage source converter (VSC)-based high voltage DC (HVDC) transmission becomes more attractive...... capacity with which the VSC-HVDC link is able to provide effective support for stabilizing the grid voltage following a grid disturbance. The developed TSA-based method implements a two-stage approximation strategy to improve the accuracy of the linear approximation. Both reactive power-based and voltage...... of offshore wind farms effectively but also to allow VSC-HVDC to contribute to system frequency regulation by adjusting its DC-link voltage. The adaptive control of the DC-link voltage enables the DC capacitors of VSC-HVDC to release/absorb energy to regulate the frequency deviation. To further enhance...

  5. Full two-dimensional rotor plane inflow measurements by a spinner-integrated wind lidar

    DEFF Research Database (Denmark)

    Sjöholm, Mikael; Pedersen, Anders Tegtmeier; Angelou, Nikolas;

    in a space filling scan pattern within a full opening angle of 60° on an upwind spherical surface. The scanner is similar to the short-range WindScanner developed at the same department. However, this implementation is only using one motor with a fixed gearing between the two prism axes in order to achieve...... a reliable implementation for turbine control applications. Main body of abstract During the summer of 2012, a proof-of-concept field campaign with the two-dimensional upwind scanning wind lidar mounted in the rotating spinner of an operating Vestas NM80 turbine (59 m hub height and 80 m rotor diameter...... surface, in the rotating coordinate frame of the spinner, bounded by the perimeter of a cone with its apex in the spinner-mounted lidar and with a full opening angle of 60°. The actual absolute measurement positions were calculated from the instantaneous positions of the two wedge-shaped optical prisms...

  6. Multiobjective Optimization in Combinatorial Wind Farms System Integration and Resistive SFCL Using Analytical Hierarchy Process

    OpenAIRE

    Moghadasi, Amirhasan; Sarwat, Arif; Guerrero, Josep M.

    2016-01-01

    This paper presents a positive approach for low voltage ride-through (LVRT) improvement of the permanent magnet synchronous generator (PMSG) based on a large wind power plant (WPP) of 50MW. The proposed method utilizes the conventional current control strategy to provide a reactive power requirement and retain the active power production during and after the fault for the grid codes compliance. Besides that, a resistive superconducting fault current limiter (RSFCL) as an additional self-heali...

  7. An Integrated Multi-Criteria Decision Making Model for Evaluating Wind Farm Performance

    OpenAIRE

    Mei-Sung Kang; Amy H. I. Lee; Pearn, W. L.; Meng-Chan Hung; He-Yau Kang

    2011-01-01

    The demands for alternative energy resources have been increasing exponentially in the 21st century due to continuous industrial development, depletion of fossil fuels and emerging environmental consciousness. Renewable energy sources, including wind energy, hydropower energy, geothermal energy, solar energy, biomass energy and ocean power, have received increasing attention as alternative means of meeting global energy demands. After Japan's Fukushima nuclear plant disaster in March 2011, mo...

  8. Contours--Monterey Canyon and Vicinity, California

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This part of DS 781 presents bathymetric contours for several seafloor maps of the Monterey Canyon and Vicinity map area, California. The raster data file is...

  9. Habitat--Monterey Canyon and Vicinity, California

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This part of DS 781 presents data for the habitat map of the seafloor of the Monterey Canyon and Vicinity map area, California. The vector data file is included in...

  10. Environmental assessment: Davis Canyon site, Utah

    Energy Technology Data Exchange (ETDEWEB)

    none,

    1986-05-01

    In February 1983, the US Department of Energy (DOE) identified the Davis Canyon site in Utah as one of the nine potentially acceptable sites for a mined geologic repository for spent nuclear fuel and high-level radioactive waste. To determine their suitability, the Davis Canyon site and the eight other potentially acceptable sites have been evaluated in accordance with the DOE's General Guidelines for the Recommendation of Sites for the Nuclear Waste Repositories. These evaluations were reported in draft environmental assessments (EAs), which were issued for public review and comment. After considering the comments received on the draft EAs, the DOE prepared the final EA. The Davis Canyon site is in the Paradox Basin, which is one of five distinct geohydrologic settings considered for the first repository. This setting contains one other potentially acceptable site -- the Lavender Canyon site. Although the Lavender Canyon site is suitable for site characterization, the DOE has concluded that the Davis Canyon site is the preferred site in the Paradox Basin. On the basis of the evaluations reported in this EA, the DOE has found that the Davis Canyon site is not disqualified under the guidelines. Furthermore, the DOE has fond that the site is suitable for site characterization because the evidence does not support a conclusion that the site will not be able to meet each of the qualifying conditions specified in the guidelines. On the basis of these findings, the DOE is nominating the Davis Canyon site as one of five sites suitable for characterization. 181 figs., 175 tabs.

  11. Adaptive Contingency Control: Wind Turbine Operation Integrated with Blade Condition Monitoring

    Data.gov (United States)

    National Aeronautics and Space Administration — We report here on first steps towards integrating systems health monitoring with adaptive contingency controls. In the scenario considered, the adaptive controller...

  12. Temperature and human thermal comfort effects of street trees across three contrasting street canyon environments

    Science.gov (United States)

    Coutts, Andrew M.; White, Emma C.; Tapper, Nigel J.; Beringer, Jason; Livesley, Stephen J.

    2016-04-01

    Urban street trees provide many environmental, social, and economic benefits for our cities. This research explored the role of street trees in Melbourne, Australia, in cooling the urban microclimate and improving human thermal comfort (HTC). Three east-west (E-W) oriented streets were studied in two contrasting street canyon forms (deep and shallow) and between contrasting tree canopy covers (high and low). These streets were instrumented with multiple microclimate monitoring stations to continuously measure air temperature, humidity, solar radiation, wind speed and mean radiant temperature so as to calculate the Universal Thermal Climate Index (UTCI) from May 2011 to June 2013, focusing on summertime conditions and heat events. Street trees supported average daytime cooling during heat events in the shallow canyon by around 0.2 to 0.6 °C and up to 0.9 °C during mid-morning (9:00-10:00). Maximum daytime cooling reached 1.5 °C in the shallow canyon. The influence of street tree canopies in the deep canyon was masked by the shading effect of the tall buildings. Trees were very effective at reducing daytime UTCI in summer largely through a reduction in mean radiant temperature from shade, lowering thermal stress from very strong (UTCI > 38 °C) down to strong (UTCI > 32 °C). The influence of street trees on canyon air temperature and HTC was highly localized and variable, depending on tree cover, geometry, and prevailing meteorological conditions. The cooling benefit of street tree canopies increases as street canyon geometry shallows and broadens. This should be recognized in the strategic placement, density of planting, and species selection of street trees.

  13. California State Waters Map Series—Monterey Canyon and vicinity, California

    Science.gov (United States)

    Dartnell, Peter; Maier, Katherine L.; Erdey, Mercedes D.; Dieter, Bryan E.; Golden, Nadine E.; Johnson, Samuel Y.; Hartwell, Stephen R.; Cochrane, Guy R.; Ritchie, Andrew C.; Finlayson, David P.; Kvitek, Rikk G.; Sliter, Ray W.; Greene, H. Gary; Davenport, Clifton W.; Endris, Charles A.; Krigsman, Lisa M.; Dartnell, Peter; Cochran, Susan A.

    2016-06-10

    IntroductionIn 2007, the California Ocean Protection Council initiated the California Seafloor Mapping Program (CSMP), designed to create a comprehensive seafloor map of high-resolution bathymetry, marine benthic habitats, and geology within the 3-nautical-mile limit of California’s State Waters. The CSMP approach is to create highly detailed seafloor maps through collection, integration, interpretation, and visualization of swath bathymetry data, acoustic backscatter, seafloor video, seafloor photography, high-resolution seismic-reflection profiles, and bottom-sediment sampling data. The map products display seafloor morphology and character, identify potential marine benthic habitats, and illustrate both the surficial seafloor geology and shallow subsurface geology.The Monterey Canyon and Vicinity map area lies within Monterey Bay in central California. Monterey Bay is one of the largest embayments along the west coast of the United States, spanning 36 km from its northern to southern tips (in Santa Cruz and Monterey, respectively) and 20 km along its central axis. Not only does it contain one of the broadest sections of continental shelf along California’s coast, it also contains Monterey Canyon, one of the largest and deepest submarine canyons in the world. Note that the California’s State Waters limit extends farther offshore between Santa Cruz and Monterey so that it encompasses all of Monterey Bay.The coastal area within the map area is lightly populated. The community of Moss Landing (population, 204) hosts the largest commercial fishing fleet in Monterey Bay in its harbor. The map area also includes parts of the cities of Marina (population, about 20,000) and Castroville (population, about 6,500). Fertile lowlands of the Salinas River and Pajaro River valleys largely occupy the inland part of the map area, and land use is primarily agricultural.The offshore part of the map area lies completely within the Monterey Bay National Marine Sanctuary. The

  14. Integrated sizing and scheduling of wind/PV/diesel/battery isolated systems

    KAUST Repository

    Malheiro, André

    2015-05-22

    In this paper we address the optimal sizing and scheduling of isolated hybrid systems using an optimization framework. The hybrid system features wind and photovoltaic conversion systems, batteries and diesel backup generators to supply electricity demand. A Mixed-Integer Linear Programming formulation is used to model system behavior over a time horizon of one year, considering hourly changes in both the availability of renewable resources and energy demand. The optimal solution is achieved with respect to the minimization of the levelized cost of energy (LCOE) over a lifetime of 20 years. Results for a case study show that the most economical solution features all four postulated subsystems. © 2015 Elsevier Ltd.

  15. A refined astronomically calibrated 40Ar/39Ar age for Fish Canyon sanidine

    NARCIS (Netherlands)

    Rivera, T.A.; Storey, M.; Zeeden, C.; Hilgen, F.J.; Kuiper, K.

    2011-01-01

    Intercalibration between the astronomical and radio-isotopic dating methods provides a means to improving accuracy and reducing uncertainty of an integrated, multi-chronometer geologic timescale. Here we report a high-precision 40Ar/39Ar age for the FishCanyon sanidine (FCs) neutron fluence monitor,

  16. Renewable Electricity Grid Integration Roadmap for Mexico. Supplement to the IEA Expert Group Report on Recommended Practices for Wind Integration Studies

    Energy Technology Data Exchange (ETDEWEB)

    Parsons, Brian [Evergreen Renewable Consulting, Evergreen, CO (United States); Cochran, Jaquelin [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Watson, Andrea [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Katz, Jessica [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bracho, Ricardo [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2015-08-19

    As a recognized leader in efforts to mitigate global climate change, the Government of Mexico (GOM) works proactively to reduce emissions, demonstrating strong political will and capacity to comprehensively address climate change. Since 2010, the U.S. government (USG) has supported these efforts by partnering with Mexico under the Enhancing Capacity for Low Emission Development Strategies (EC-LEDS) program. Through the program, the USG has partnered with Mexico’s Ministry of Energy (SENER), as well as other government agencies, to support GOM in reaching its clean energy and climate change goals. Specifically, the EC-LEDS program is supporting GOM’s clean energy goal of generating 35% of its electricity from renewable energy (RE) by 2024. EC-LEDS, through the U.S. Agency for International Development (USAID) and the U.S Department of Energy’s (DOE’s) National Renewable Energy Laboratory (NREL), has been collaborating with SENER and GOM interagency working group—the Consejo Consultivo para las Energías Renovables (Consultative Council on Renewable Energy)—to create a grid integration roadmap for variable RE. 1 A key objective in creating a grid integration roadmap is assessing likely impacts of wind and solar energy on the power system and modifying planning and operations accordingly. This paper applies best practices in conducting a grid integration study to the Mexican context.

  17. Canyon conditions impact carbon flows in food webs of three sections of the Nazare canyon

    NARCIS (Netherlands)

    van Oevelen, D.; Soetaert, K.; Garcia, R.; de Stigter, H.C.; Cunha, M.R.; Pusceddu, A.; Danovaro, R.; Garcia, R.

    2011-01-01

    Submarine canyons transport large amounts of sediment and organic matter (OM) from the continental shelf to the abyssal plain. Three carbon-based food web models were constructed for the upper (300-750 m water depth), middle (2700-3500 m) and lower section (4000-5000 m) of the Nazare canyon (eastern

  18. The Whittard Canyon – a case study of submarine canyon processes

    NARCIS (Netherlands)

    Amaro, T.; Huvenne, V.A.I.; Allcock, A.L.; Aslam, T.; Davies, J.S.; Danovaro, R.; de Stigter, H.C.; Duineveld, G.C.A.; Gambi, C.; Gooday, A.J.; Gunton, L.M.; Hall, R.; Howell, K.L.; Ingels, J.; Kiriakoulakis, K.; Kershaw, C.E.; Lavaleye, M.; Robert, K.; Stewart, H.; Van Rooij, D.; White, M.; Wilson, A.M.

    2016-01-01

    Submarine canyons are large geomorphological features that incise continental shelves and slopes around the world. They are often suggested to be biodiversity and biomass hotspots, although there is no consensus about this in the literature. Nevertheless, many canyons do host diverse faunal communit

  19. The Whittard Canyon – A case study of submarine canyon processes

    NARCIS (Netherlands)

    Amaro, T.; Huvenne, V.A.I.; Allcock, A.L.; Aslam, T.; Davies, J.S.; Danovaro, R.; de Stigter, H.C.; Duineveld, G.C.A.; Gambi, C.; Gooday, A.J.; Gunton, L.M.; Hall, R.; Howell, K.L.; Ingels, J.; Kiriakoulakis, K.; Kershaw, C.E.; Lavaleye, M.; Robert, K.; Stewart, H.; Van Rooij, D.; White, M.; Wilson, A.M.

    2016-01-01

    Submarine canyons are large geomorphological features that incise continental shelves and slopes around the world. They are often suggested to be biodiversity and biomass hotspots, although there is no consensus about this in the literature. Nevertheless, many canyons do host diverse faunal communit

  20. INVESTIGATION OF A DYNAMIC POWER LINE RATING CONCEPT FOR IMPROVED WIND ENERGY INTEGRATION OVER COMPLEX TERRAIN

    Energy Technology Data Exchange (ETDEWEB)

    Jake P. Gentle; Kurt S Myers; Tyler B Phillips; Inanc Senocak; Phil Anderson

    2014-08-01

    Dynamic Line Rating (DLR) is a smart grid technology that allows the rating of power line to be based on real-time conductor temperature dependent on local weather conditions. In current practice overhead power lines are generally given a conservative rating based on worst case weather conditions. Using historical weather data collected over a test bed area, we demonstrate there is often additional transmission capacity not being utilized with the current static rating practice. We investigate a new dynamic line rating methodology using computational fluid dynamics (CFD) to determine wind conditions along transmission lines at dense intervals. Simulated results are used to determine conductor temperature by calculating the transient thermal response of the conductor under variable environmental conditions. In calculating the conductor temperature, we use both a calculation with steady-state assumption and a transient calculation. Under low wind conditions, steady-state assumption predicts higher conductor temperatures that could lead to curtailments, whereas transient calculations produce conductor temperatures that are significantly lower, implying the availability of additional transmission capacity.

  1. RESEARCH AND DEVELOPMENT ACTIVITIES AT SAVANNAH RIVER SITE'S H CANYON FACILITY

    Energy Technology Data Exchange (ETDEWEB)

    Sexton, Lindsay; Fuller, Kenneth

    2013-07-09

    The Savannah River Site's (SRS) H Canyon Facility is the only large scale, heavily shielded, nuclear chemical separations plant still in operation in the U.S. The facility's operations historically recovered uranium-235 (U-235) and neptunium-237 (Np-237) from aluminum-clad, enriched-uranium fuel tubes from Site nuclear reactors and other domestic and foreign research reactors. Today the facility, in conjunction with HB Line, is working to provide the initial feed material to the Mixed Oxide Facility also located on SRS. Many additional campaigns are also in the planning process. Furthermore, the facility has started to integrate collaborative research and development (R&D) projects into its schedule. H Canyon can serve as the appropriate testing location for many technologies focused on monitoring the back end of the fuel cycle, due to the nature of the facility and continued operation. H Canyon, in collaboration with the Savannah River National Laboratory (SRNL), has been working with several groups in the DOE complex to conduct testing demonstrations of novel technologies at the facility. The purpose of conducting these demonstrations at H Canyon will be to demonstrate the capabilities of the emerging technologies in an operational environment. This paper will summarize R&D testing activities currently taking place in H Canyon and discuss the possibilities for future collaborations.

  2. Fault tree analysis of Project S-4404, Upgrade Canyon Exhaust System

    International Nuclear Information System (INIS)

    Project S-4404, Upgrade Canyon Exhaust Systems, is a $177 million project with the purpose of upgrading the Exhaust Systems for both F and H Canyon Facilities. This upgrade will replace major portions of the F and H-Canyon exhaust systems, downstream of their respective sand filters with higher capacity and more reliable systems. Because of the high cost, DOE requested Program Control ampersand Integration (PC ampersand I) to examine specific deletions to the project. PC ampersand I requested Nuclear Processes Safety Research (NPSR) to perform an analysis to compare failure rates for the existing F ampersand H Canyon exhaust systems with the proposed exhaust system and specific proposed exhaust system alternatives. The objective of this work was to perform an analysis and compare failure rates for the existing F ampersand H Canyon exhaust systems with the proposed project exhaust system and proposed project alternatives. Based on fault tree analysis, two conclusions are made. First, D ampersand D activities can be eliminated from the project with no significant decrease to exhaust system safety. Deletion of D ampersand D activities would result in a cost savings of $29 million. Second, deletion of DOE Order 6430.1A requirements regarding DBAs would decrease exhaust system safety by a factor of 12

  3. Flushing of a dense fluid from an urban canyon part 1: Steady state measurements

    Science.gov (United States)

    Kaye, Nigel; Baratian, Zahra

    2011-11-01

    We consider the role of buoyancy on the vertical transport of a dense gas due to a horizontal wind flow above a street canyon. The density of the pollutant suppresses vertical mixing as the turbulent shear flow at the top of the canyon must do work to raise the dense gas up above the canyon top. We present results of a series of experiments to measure the rate of removal of a dense miscible fluid from a two dimensional square canyon open at the top. The cavity is formed by square blocks up- and down-stream. Dense fluid is introduced at a constant rate at the base of the cavity and is removed by mixing with the flow passing over the top of the cavity. Two different steady flows are observed. For higher Richardson numbers, a two layer stratification develops in which there is a relatively sharp interface. In this case the mixing is parameterized in terms of an entrainment velocity across the interface that is a function of the Richardson number and the fractional depth of the interface below the cavity top. For lower Richardson numbers no interface is observed and the buoyancy increases linearly with height above the cavity base. We also found a range of Richardson numbers for which both steady stratifications are possible and for which the steady flow depends on the initial conditions.

  4. A Low-Carbon Dispatch Model in a Wind Power Integrated System Considering Wind Speed Forecasting and Energy-Environmental Efficiency

    OpenAIRE

    Jian Zhao; Bichang Zou; Xiaohui Zhang; Qingwu Gong; Daojun Chen

    2012-01-01

    This paper introduces the “Energy-Environmental Efficiency†concept of building a low-carbon dispatch model of wind-incorporated power systems from the perspective of environmental protection and low-carbon dispatch promotion based on the existing economic environmental dispatch. A rolling auto-regressive and moving-average model is adopted to forecast wind speeds for the next 24 h and reduce the disadvantages brought about to the power system dispatch by wind speed fluctuations. A fuzzy s...

  5. A mixed spectral-integration model for neutral mean wind flow over hills

    DEFF Research Database (Denmark)

    Corbett, Jean-Francois; Ott, Søren; Landberg, Lars

    2008-01-01

    equations are solved spectrally horizontally and by numerical integration vertically. Non-dimensional solutions are stored in look-up tables for quick re-use. Model results are compared to measurements, as well as other authors' flow models in three test cases. The model is implemented and tested in two...

  6. Wind Energy

    Energy Technology Data Exchange (ETDEWEB)

    Beurskens, H.J.M. [SET Analysis, Kievitlaan 26, 1742 AD Schagen (Netherlands); Brand, A.J. [Energy research Centre of the Netherlands ECN, Unit Wind Energy, P.O. Box 1, 1755 ZG Petten (Netherlands)

    2013-02-15

    Over the years, wind energy has become a major source of renewable energy worldwide. The present chapter addresses the wind resource, which is available for exploitation for large-scale electricity production, and its specific physical properties. Furthermore, the technical options available to convert the energy of the air flow into mechanical energy and electricity are described. Specific problems of large-scale integration of wind energy into the grid as well as the present and future market developments are described in this chapter. Finally, environmental aspects are discussed briefly.

  7. Tectonic activity and the evolution of submarine canyons: The Cook Strait Canyon system, New Zealand

    Science.gov (United States)

    Micallef, Aaron; Mountjoy, Joshu; Barnes, Philip; Canals, Miquel; Lastras, Galderic

    2016-04-01

    Submarine canyons are Earth's most dramatic erosional features, comprising steep-walled valleys that originate in the continental shelf and slope. They play a key role in the evolution of continental margins by transferring sediments into deep water settings and are considered important biodiversity hotspots, pathways for nutrients and pollutants, and analogues of hydrocarbon reservoirs. Although comprising only one third of continental margins worldwide, active margins host more than half of global submarine canyons. We still lack of thorough understanding of the coupling between active tectonics and submarine canyon processes, which is necessary to improve the modelling of canyon evolution in active margins and derive tectonic information from canyon morphology. The objectives of this study are to: (i) understand how tectonic activity influences submarine canyon morphology, processes, and evolution in an active margin, and (2) formulate a generalised model of canyon development in response to tectonic forcing based on morphometric parameters. We fulfil these objectives by analysing high resolution geophysical data and imagery from Cook Strait Canyon system, offshore New Zealand. Using these data, we demonstrate that tectonic activity, in the form of major faults and structurally-generated tectonic ridges, leaves a clear topographic signature on submarine canyon location and morphology, in particular their dendritic and sinuous planform shapes, steep and linear longitudinal profiles, and cross-sectional asymmetry and width. We also report breaks/changes in canyon longitudinal slope gradient, relief and slope-area regression models at the intersection with faults. Tectonic activity gives rise to two types of knickpoints in the Cook Strait Canyon. The first type consists of low slope gradient, rounded and diffusive knickpoints forming as a result of short wavelength folds or fault break outs and being restored to an equilibrium profile by upstream erosion and

  8. Power conditioning system topology for grid integration of wind and fuell cell energy

    Directory of Open Access Journals (Sweden)

    Marian GAICEANU

    2006-12-01

    Full Text Available This paper shows the topology of the hybrid grid-connected power system and the performances of the front-end three-phase power inverter. The renewable sources of the hybrid power system consist of a solid oxide fuel cell and a wind-turbine. This type of combination is the most efficient one. The proposed topology benefits of the one common DC-AC inverter which injects the generated power into the grid. The architecture diminishes the cost of the power conditioning system. Moreover, due to the power balance control of the entire power conditioning system the bulk dc link electrolytic capacitor is replaced with a small plastic film one. The final power conditioning system has the following advantages: independent control of the reactive power, minimize harmonic current distortion offering a nearly unity power factor operation (0,998 operation capability, dc link voltage regulation (up to 5% ripple in the dc-link voltage in any operated conditions, fast disturbance compensation capability, high reliability, and low cost. The experimental test has been performed and the performances of the grid power inverter are shown.

  9. General Forced Oscillations in a Real Power Grid Integrated with Large Scale Wind Power

    Directory of Open Access Journals (Sweden)

    Ping Ju

    2016-07-01

    Full Text Available According to the monitoring of the wide area measurement system, inter-area oscillations happen more and more frequently in a real power grid of China, which are close to the forced oscillation. Applying the conventional forced oscillation theory, the mechanism of these oscillations cannot be explained well, because the oscillations vary with random amplitude and a narrow frequency band. To explain the mechanism of such oscillations, the general forced oscillation (GFO mechanism is taken into consideration. The GFO is the power system oscillation excited by the random excitations, such as power fluctuations from renewable power generation. Firstly, properties of the oscillations observed in the real power grid are analyzed. Using the GFO mechanism, the observed oscillations seem to be the GFO caused by some random excitation. Then the variation of the wind power measured in this power gird is found to be the random excitation which may cause the GFO phenomenon. Finally, simulations are carried out and the power spectral density of the simulated oscillation is compared to that of the observed oscillation, and they are similar with each other. The observed oscillation is thus explained well using the GFO mechanism and the GFO phenomenon has now been observed for the first time in real power grids.

  10. Integrating Wind Profiling Radars and Radiosonde Observations with Model Point Data to Develop a Decision Support Tool to Assess Upper-Level Winds for Space Launch

    Science.gov (United States)

    Bauman, William H., III; Flinn, Clay

    2013-01-01

    On the day of launch, the 45th Weather Squadron (45 WS) Launch Weather Officers (LWOs) monitor the upper-level winds for their launch customers. During launch operations, the payload/launch team sometimes asks the LWOs if they expect the upper-level winds to change during the countdown. The LWOs used numerical weather prediction model point forecasts to provide the information, but did not have the capability to quickly retrieve or adequately display the upper-level observations and compare them directly in the same display to the model point forecasts to help them determine which model performed the best. The LWOs requested the Applied Meteorology Unit (AMU) develop a graphical user interface (GUI) that will plot upper-level wind speed and direction observations from the Cape Canaveral Air Force Station (CCAFS) Automated Meteorological Profiling System (AMPS) rawinsondes with point forecast wind profiles from the National Centers for Environmental Prediction (NCEP) North American Mesoscale (NAM), Rapid Refresh (RAP) and Global Forecast System (GFS) models to assess the performance of these models. The AMU suggested adding observations from the NASA 50 MHz wind profiler and one of the US Air Force 915 MHz wind profilers, both located near the Kennedy Space Center (KSC) Shuttle Landing Facility, to supplement the AMPS observations with more frequent upper-level profiles. Figure 1 shows a map of KSC/CCAFS with the locations of the observation sites and the model point forecasts.

  11. 78 FR 21415 - Glen Canyon Dam Adaptive Management Work Group

    Science.gov (United States)

    2013-04-10

    ... Bureau of Reclamation Glen Canyon Dam Adaptive Management Work Group AGENCY: Bureau of Reclamation, Interior. ACTION: Notice of public meeting. SUMMARY: The Glen Canyon Dam Adaptive Management Work Group..., the AMWG, a technical work group, a Grand Canyon Monitoring and Research Center, and...

  12. 77 FR 9265 - Glen Canyon Dam Adaptive Management Work Group

    Science.gov (United States)

    2012-02-16

    ... Bureau of Reclamation Glen Canyon Dam Adaptive Management Work Group AGENCY: Bureau of Reclamation, Interior. ACTION: Notice of public meeting. SUMMARY: The Glen Canyon Dam Adaptive Management Work Group... Federal advisory committee, the AMWG, a technical work group (TWG), a Grand Canyon Monitoring and...

  13. 77 FR 43117 - Glen Canyon Dam Adaptive Management Work Group

    Science.gov (United States)

    2012-07-23

    ... Bureau of Reclamation Glen Canyon Dam Adaptive Management Work Group AGENCY: Bureau of Reclamation, Interior. ACTION: Notice of public meeting. SUMMARY: The Glen Canyon Dam Adaptive Management Work Group... Federal advisory committee, the AMWG, a technical work group (TWG), a Grand Canyon Monitoring and...

  14. 27 CFR 9.152 - Malibu-Newton Canyon.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Malibu-Newton Canyon. 9... Malibu-Newton Canyon. (a) Name. The name of the viticultural area described in this petition is “Malibu-Newton Canyon.” (b) Approved maps. The appropriate map for determining the boundary of the...

  15. Thermal comfort in an east-west oriented street canyon in Freiburg (Germany) under hot summer conditions

    Science.gov (United States)

    Ali-Toudert, F.; Mayer, H.

    2007-01-01

    Field-measurements were conducted in an urban street canyon with an east-west orientation, and a height-to-width ratio H/W = 1 during cloudless summer weather in 2003 in Freiburg, Germany. This experimental work adds to the knowledge available on the microclimate of an urban canyon and its impact on human comfort. Air temperature T a , air humidity VP, wind speed v and direction dd were measured continuously. All short-wave and long-wave radiation fluxes from the 3D surroundings were also measured. The degree of comfort was defined in terms of physiologically equivalent temperature (PET). Furthermore, the data gathered within the canyon were compared to data collected by a permanent urban climate station with the aim of furthering the understanding of microclimatic changes due to street geometry. Changes in the meteorological variables T a , v and dd in the canyon in comparison to an unobstructed roof level location were found to be in good agreement with previous studies, i.e., a small increase of T a in the canyon adjacent to irradiated surfaces, and a good correlation of v and dd between canyon and roof levels. The daily dynamics of canyon facet irradiances and their impacts on the heat gained by a pedestrian were strongly dependent on street geometry and orientation. Thermal stress was mostly attributable to solar exposure. Under cloudless summer weather, a standing body was found to absorb, on average, 74% of heat in the form of long-wave irradiance and 26% as short-wave irradiance. Shading the pedestrian as well as the surrounding surfaces is, hence, the first strategy in mitigating heat stress in summer under hot conditions.

  16. An Optimal Integrated Control Scheme for Permanent Magnet Synchronous Generator-Based Wind Turbines under Asymmetrical Grid Fault Conditions

    Directory of Open Access Journals (Sweden)

    Dan Wang

    2016-04-01

    Full Text Available In recent years, the increasing penetration level of wind energy into power systems has brought new issues and challenges. One of the main concerns is the issue of dynamic response capability during outer disturbance conditions, especially the fault-tolerance capability during asymmetrical faults. In order to improve the fault-tolerance and dynamic response capability under asymmetrical grid fault conditions, an optimal integrated control scheme for the grid-side voltage-source converter (VSC of direct-driven permanent magnet synchronous generator (PMSG-based wind turbine systems is proposed in this paper. The optimal control strategy includes a main controller and an additional controller. In the main controller, a double-loop controller based on differential flatness-based theory is designed for grid-side VSC. Two parts are involved in the design process of the flatness-based controller: the reference trajectories generation of flatness output and the implementation of the controller. In the additional control aspect, an auxiliary second harmonic compensation control loop based on an improved calculation method for grid-side instantaneous transmission power is designed by the quasi proportional resonant (Quasi-PR control principle, which is able to simultaneously restrain the second harmonic components in active power and reactive power injected into the grid without the respective calculation for current control references. Moreover, to reduce the DC-link overvoltage during grid faults, the mathematical model of DC-link voltage is analyzed and a feedforward modified control factor is added to the traditional DC voltage control loop in grid-side VSC. The effectiveness of the optimal control scheme is verified in PSCAD/EMTDC simulation software.

  17. Instability of outer tip vortices for a 2.5 MW wind turbine: integrating snow PIV with LES

    Science.gov (United States)

    Sotiropoulos, Fotis; Yang, Xiaolei; Hong, Jiarong; Barone, Matthew

    2015-11-01

    Recent field experiments conducted around a 2.5 MW wind turbine using super-large-scale PIV (SLPIV) using natural snow particles have revealed tip vortex cores (visualized as areas devoid of snowflakes) of complex shape, consisting of both round and elongated void patterns. Here we employ large-eddy simulation to elucidate the structure and dynamics of the complex tip vortices identified experimentally. The LES is shown to reproduce vortex cores in remarkable agreement with the SLPIV results, essentially capturing all vortex core patterns observed in the field in the tip shear layer. We show that the stretched elongated vortex cores observed in 2D planes are the footprints of a second set of counter-rotating spiral vortices that emanates along the tip shear layer immediately downwind of the blades and is intertwined with the tip vortices. We argue that this large-scale instability is of centrifugal type since the mean flow characteristics in the outer tip shear layer resemble those of the Taylor-Couette flow. This study highlights the feasibility of employing snow voids to visualize tip vortices and demonstrates the enormous potential of integrating SLPIV with LES as a powerful tool for gaining novel insights into the wakes of utility scale wind turbines. This work was supported by Department of Energy DOE (DE-EE0002980, DE-EE0005482 and DE-AC04-94AL85000), Sandia National Laboratories and NSF Career Award (NSF-CBET-1454259) for Jiarong Hong. Computational resources were provided by SNL and MSI.

  18. Let's Bet on Sediments! Hudson Canyon Cruise--Grades 9-12. Focus: Sediments of Hudson Canyon.

    Science.gov (United States)

    National Oceanic and Atmospheric Administration (DOC), Rockville, MD.

    These activities are designed to teach about the sediments of Hudson Canyon. Students investigate and analyze the patterns of sedimentation in the Hudson Canyon, observe how heavier particles sink faster than finer particles, and learn that submarine landslides are avalanches of sediment in deep ocean canyons. The activity provides learning…

  19. Geohydrology of White Rock Canyon of the Rio Grande from Otowi to Frijoles Canyon

    International Nuclear Information System (INIS)

    Twenty-seven springs discharge from the Totavi Lentil and Tesuque Formation in White Rock Canyon. Water generally acquires its chemical characteristics from rock units that comprise the spring aquifer. Twenty-two of the springs are separated into three groups of similar aquifer-related chemical quality. The five remaining springs make up a fourth group with a chemical quality that differs due to localized conditions in the aquifer. Localized conditions may be related to recharge or discharge in or near basalt intrusion or through faults. Streams from Pajarito, Ancho, and Frijoles Canyons discharge into the Rio Grande in White Rock Canyon. The base flow in the streams is from springs. Sanitary effluent in Mortandad Canyon from the treatment plant at White Rock also reaches the Rio Grande

  20. Performance of Generating Plant: Managing the Changes. Supporting paper: The evolution of the electricity sector and renewable sources in Italy: opportunities and problems for wind power integration

    Energy Technology Data Exchange (ETDEWEB)

    Salvaderi, Luigi [IEEE Fellow (Italy)

    2008-05-15

    The WEC Committee on the Performance of Generating Plant (PGP) has been collecting and analysing power plant performance statistics worldwide for more than 30 years and has produced regular reports, which include examples of advanced techniques and methods for improving power plant performance through benchmarking. A series of reports from the various working groups was issued in 2008. This document serves as a supporting paper. Sections include: features of Italian energy and electricity; the evolution of liberalisation; support mechanism for renewables; connection to wind farm transmission network; wind source integration into power system; and, final comments.

  1. A Low-Carbon Dispatch Model in a Wind Power Integrated System Considering Wind Speed Forecasting and Energy-Environmental Efficiency

    Directory of Open Access Journals (Sweden)

    Jian Zhao

    2012-04-01

    Full Text Available This paper introduces the “Energy-Environmental Efficiency” concept of building a low-carbon dispatch model of wind-incorporated power systems from the perspective of environmental protection and low-carbon dispatch promotion based on the existing economic environmental dispatch. A rolling auto-regressive and moving-average model is adopted to forecast wind speeds for the next 24 h and reduce the disadvantages brought about to the power system dispatch by wind speed fluctuations. A fuzzy satisfaction-maximizing approach is employed to convert the multi-objective decision-making problem in the low-carbon dispatch model into a single nonlinear one. Particle swarm optimization with a simulated annealing algorithm hybrid is used for better solutions. Simulation results show that the energy-environmental efficiency concept benefits the optimization of the proposed power system dispatch, and the proposed low-carbon dispatch model is reasonable and practical.

  2. 78 FR 7775 - Boulder Canyon Project

    Science.gov (United States)

    2013-02-04

    .... \\1\\ 75 FR 57912 (September 23, 2010). \\2\\ 133 FERC ] 62,229. The proposed BCP electric service base... in power rate adjustments (10 CFR part 903) were published on September 18, 1985 (50 FR 87835... Area Power Administration Boulder Canyon Project AGENCY: Western Area Power Administration, DOE....

  3. ACUMEN 2012: Atlantic Canyons Undersea Mapping Expeditions

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Between February and August 2012, a team of NOAA and external partners will conduct a mapping ‘blitz’ focused on deepwater canyons off the northeastern...

  4. Anatomy of La Jolla submarine canyon system; offshore southern California

    Science.gov (United States)

    Paull, C.K.; Caress, D.W.; Lundsten, E.; Gwiazda, R.; Anderson, K.; McGann, M.; Conrad, J.; Edwards, B.; Sumner, E.J.

    2013-01-01

    An autonomous underwater vehicle (AUV) carrying a multibeam sonar and a chirp profiler was used to map sections of the seafloor within the La Jolla Canyon, offshore southern California, at sub-meter scales. Close-up observations and sampling were conducted during remotely operated vehicle (ROV) dives. Minisparker seismic-reflection profiles from a surface ship help to define the overall geometry of the La Jolla Canyon especially with respect to the pre-canyon host sediments. The floor of the axial channel is covered with unconsolidated sand similar to the sand on the shelf near the canyon head, lacks outcrops of the pre-canyon host strata, has an almost constant slope of 1.0° and is covered with trains of crescent shaped bedforms. The presence of modern plant material entombed within these sands confirms that the axial channel is presently active. The sand on the canyon floor liquefied during vibracore collection and flowed downslope, illustrating that the sediment filling the channel can easily fail even on this gentle slope. Data from the canyon walls help constrain the age of the canyon and extent of incision. Horizontal beds of moderately cohesive fine-grained sediments exposed on the steep canyon walls are consistently less than 1.232 million years old. The lateral continuity of seismic reflectors in minisparker profiles indicate that pre-canyon host strata extend uninterrupted from outside the canyon underneath some terraces within the canyon. Evidence of abandoned channels and point bar-like deposits are noticeably absent on the inside bend of channel meanders and in the subsurface of the terraces. While vibracores from the surface of terraces contain thin (< 10 cm) turbidites, they are inferred to be part of a veneer of recent sediment covering pre-canyon host sediments that underpin the terraces. The combined use of state of the art seafloor mapping and exploration tools provides a uniquely detailed view of the morphology within an active submarine canyon.

  5. Integration of Wind Energy, Hydrogen and Natural Gas Pipeline Systems to Meet Community and Transportation Energy Needs: A Parametric Study

    OpenAIRE

    Shahryar Garmsiri; Marc A. Rosen; Gordon Rymal Smith

    2014-01-01

    The potential benefits are examined of the “Power-to-Gas†(P2G) scheme to utilize excess wind power capacity by generating hydrogen (or potentially methane) for use in the natural gas distribution grid. A parametric analysis is used to determine the feasibility and size of systems producing hydrogen that would be injected into the natural gas grid. Specifically, wind farms located in southwestern Ontario, Canada are considered. Infrastructure requirements, wind farm size, pipeline capacity...

  6. Optimization of Operation Reserve Coordination Considering Wind Power Integration%考虑风电接入的有功运行备用协调优化

    Institute of Scientific and Technical Information of China (English)

    张国强; 吴文传; 张伯明

    2011-01-01

    分析了大量风电接入对系统有功运行备用提出的问题,首先分析了风电接入后系统的运行备用需求性质,进而提出一种基于风险的风电备用需求决策方法,并提出一种充分利用发电机组控制性能的备用协调优化分配算法.IEEE 39节点系统的仿真结果表明,所提出的方法有效解决了风电备用需求的确定和分配问题,对接入大量风电的系统的有功调度运行具有实用价值.%The impact of wind power integration on the system active operation reserve is analyzed. The characteristics of operating reserve are discussed, and a risk-based reserve decision method for wind power integration is presented.A coordination and optimal reserve allocation algorithm is proposed to take full advantage of the control performance of generators, which is capable of solving the wind power impact on the operation reserve. Simulation results of an IEEE 39-bus system show that the method proposed is effective in determining and allocating the wind power reserve demands and of practical value in integrating massive active dispatch operation of the wind power system.

  7. Conditions and processes affecting sand resources at archeological sites in the Colorado River corridor below Glen Canyon Dam, Arizona

    Science.gov (United States)

    East, Amy E.; Collins, Brian D.; Sankey, Joel B.; Corbett, Skye C.; Fairley, Helen C.; Caster, Joshua

    2016-05-17

    This study examined links among fluvial, aeolian, and hillslope geomorphic processes that affect archeological sites and surrounding landscapes in the Colorado River corridor downstream from Glen Canyon Dam, Arizona. We assessed the potential for Colorado River sediment to enhance the preservation of river-corridor archeological resources through aeolian sand deposition or mitigation of gully erosion. By identifying locally prevailing wind directions, locations of modern sandbars, and likely aeolian-transport barriers, we determined that relatively few archeological sites are now ideally situated to receive aeolian sand supply from sandbars deposited by recent controlled floods. Whereas three-fourths of the 358 river-corridor archeological sites we examined include Colorado River sediment as an integral component of their geomorphic context, only 32 sites currently appear to have a high degree of connectivity (coupled interactions) between modern fluvial sandbars and sand-dominated landscapes downwind. This represents a substantial decrease from past decades, as determined by aerial-photograph analysis. Thus, we infer that recent controlled floods have had a limited, and declining, influence on archeological-site preservation.

  8. System Integration of the Horizontal-Axis Wind Turbine: The Design of Turbine Blades with an Axial-Flux Permanent Magnet Generator

    OpenAIRE

    Chi-Jeng Bai; Wei-Cheng Wang; Po-Wei Chen; Wen-Tong Chong

    2014-01-01

    In designing a horizontal-axis wind turbine (HAWT) blade, system integration between the blade design and the performance test of the generator is important. This study shows the aerodynamic design of a HAWT blade operating with an axial-flux permanent magnet (AFPM) generator. An experimental platform was built to measure the performance curves of the AFPM generator for the purpose of designing the turbine blade. An in-house simulation code was developed based on the blade element momentum (B...

  9. Results from the Bell Canyon borehole plugging test

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, C. L.

    1980-01-01

    The BHP is an integrated program involving consequence assessment and plug performance calculations, materials evaluation, instrumentation development and field testing, and interfaces directly with other WIPP-related activities. This paper describes an in situ test conducted under the BHP Field Test Task. The Bell Canyon Test was conducted to evaluate candidate grout plugging mixes and plug emplacement techniques, and to assess plug performance under in-situ cure conditions. Laboratory testing of the brine-grout/rock combination revealed an adverse reaction between the brine-grout and the anhydrite. This discovery permitted a timely change to an additional laboratory compatibility testing program with an alternate fresh-water mix to permit maintenance of the test schedule with little delay. While cement emplacement technology is generally adequate to satisfy repository plugging requirements, plug compatibility with the host rock must be carefully assessed for each repository site. Generally accepted laboratory cement-testing techniques need to include flow characteristics and geochemical stability.

  10. Techno-economic Modeling of the Integration of 20% Wind and Large-scale Energy Storage in ERCOT by 2030

    Energy Technology Data Exchange (ETDEWEB)

    Baldick, Ross; Webber, Michael; King, Carey; Garrison, Jared; Cohen, Stuart; Lee, Duehee

    2012-12-21

    This study's objective is to examine interrelated technical and economic avenues for the Electric Reliability Council of Texas (ERCOT) grid to incorporate up to and over 20% wind generation by 2030. Our specific interests are to look at the factors that will affect the implementation of both high level of wind power penetration (> 20% generation) and installation of large scale storage.

  11. Study on Integration Simulation of D-PMSG Wind Power Farm%永磁直驱型风电场的并网仿真研究

    Institute of Scientific and Technical Information of China (English)

    龚陈雄; 王剑; 吴丹岳; 郑建辉; 许志红

    2014-01-01

    为了研究风电并网对接入点电网电压的影响,以永磁直驱风力发电机组为研究对象,在 PSCAD/EMTDC仿真平台上建立基于实际运行数据的永磁直驱风电机组仿真模型,并进行风电场等值建模。利用 BPA 和PSCAD/EMTDC软件建立福建省某区域电网的等值模型,对大规模风电接入区域电网引起的电网电压稳态和暂态过程进行分析。得出结论:永磁直驱风电场能够对输出的功率和无功功率进行控制,当风电并网系统输电线路中的电阻不能忽略时,风电场出口电压会产生正偏差。最后提出在直驱型风电场集中的地区建立一个以功率和无功功率为调控量、以维持电压稳定为目标的风电汇集线路电网电压自动控制系统的建议。%For studying impact on voltage of access point power grid of wind power integration,this paper takes D-PMSG wind power generator as study object and establishes D-PMSG simulation model on PSCAD/EMTDC simulation platform and proceeds equivalent modeling for wind power farm.By using BPA and PSCAD/EMTDC software,it establishes equivalent model for some area power grid in Fujian province and analyzes voltage stable state and transient process caused by large-scale wind power connection into areal power grid.It draws a conclusion that permanent magnetic direct drive wind power farm is able to control output power and reactive power.When resistance in transmission line of wind power integration sys-tem is not able to be ignored,there is to produce positive derivation exit voltage in wind power farm.At last,it proposes to establish voltage automatic control system for wind power assemble lines which is taking power and reactive power as regula-ting amount and keeping voltage stabile for target.

  12. Integrated analysis of DFIG drive-train and power electronics dynamics during electrical AC faults and wind disturbances

    DEFF Research Database (Denmark)

    Barahona Garzón, Braulio; Sørensen, Poul Ejnar; Anaya-Lara, Olimpo;

    2013-01-01

    The dynamics of a 2 MW DFIG wind turbine are studied during electrical AC faults, and wind disturbances. A simulation platform that couples HAWC2, and Matlab/Simulink was used. High frequencies of the gear box, and power electronics are neglected. It was shown that the dynamics of the dc-link are......The dynamics of a 2 MW DFIG wind turbine are studied during electrical AC faults, and wind disturbances. A simulation platform that couples HAWC2, and Matlab/Simulink was used. High frequencies of the gear box, and power electronics are neglected. It was shown that the dynamics of the dc......-link are influenced by turbulence, and wind gusts. An AC fault that triggers protection systems was simulated, and the influence on the dc-link voltage, shaft and tower loading illustrated....

  13. Surprise and opportunity for learning in Grand Canyon: the Glen Canyon Dam Adaptive Management Program

    Science.gov (United States)

    Melis, Theodore S.; Walters, Carl; Korman, Josh

    2015-01-01

    With a focus on resources of the Colorado River ecosystem below Glen Canyon Dam, the Glen Canyon Dam Adaptive Management Program has included a variety of experimental policy tests, ranging from manipulation of water releases from the dam to removal of non-native fish within Grand Canyon National Park. None of these field-scale experiments has yet produced unambiguous results in terms of management prescriptions. But there has been adaptive learning, mostly from unanticipated or surprising resource responses relative to predictions from ecosystem modeling. Surprise learning opportunities may often be viewed with dismay by some stakeholders who might not be clear about the purpose of science and modeling in adaptive management. However, the experimental results from the Glen Canyon Dam program actually represent scientific successes in terms of revealing new opportunities for developing better river management policies. A new long-term experimental management planning process for Glen Canyon Dam operations, started in 2011 by the U.S. Department of the Interior, provides an opportunity to refocus management objectives, identify and evaluate key uncertainties about the influence of dam releases, and refine monitoring for learning over the next several decades. Adaptive learning since 1995 is critical input to this long-term planning effort. Embracing uncertainty and surprise outcomes revealed by monitoring and ecosystem modeling will likely continue the advancement of resource objectives below the dam, and may also promote efficient learning in other complex programs.

  14. The influence of controlled floods on fine sediment storage in debris fan-affected canyons of the Colorado River basin

    Science.gov (United States)

    Mueller, Erich R.; Grams, Paul E.; Schmidt, John C.; Hazel, Joseph E., Jr.; Alexander, Jason S.; Kaplinski, Matt

    2014-01-01

    Prior to the construction of large dams on the Green and Colorado Rivers, annual floods aggraded sandbars in lateral flow-recirculation eddies with fine sediment scoured from the bed and delivered from upstream. Flows greater than normal dam operations may be used to mimic this process in an attempt to increase time-averaged sandbar size. These controlled floods may rebuild sandbars, but sediment deficit conditions downstream from the dams restrict the frequency that controlled floods produce beneficial results. Here, we integrate complimentary, long-term monitoring data sets from the Colorado River in Marble and Grand Canyons downstream from Glen Canyon dam and the Green River in the Canyon of Lodore downstream from Flaming Gorge dam. Since the mid-1990s, several controlled floods have occurred in these canyon rivers. These controlled floods scour fine sediment from the bed and build sandbars in eddies, thus increasing channel relief. These changes are short-lived, however, as interflood dam operations erode sandbars within several months to years. Controlled flood response and interflood changes in bed elevation are more variable in Marble Canyon and Grand Canyon, likely reflecting more variable fine sediment supply and stronger transience in channel bed sediment storage. Despite these differences, neither system shows a trend in fine-sediment storage during the period in which controlled floods were monitored. These results demonstrate that controlled floods build eddy sandbars and increase channel relief for short interflood periods, and this response may be typical in other dam-influenced canyon rivers. The degree to which these features persist depends on the frequency of controlled floods, but careful consideration of sediment supply is necessary to avoid increasing the long-term sediment deficit.

  15. Impact of trees on pollutant dispersion in street canyons: A numerical study of the annual average effects in Antwerp, Belgium.

    Science.gov (United States)

    Vranckx, Stijn; Vos, Peter; Maiheu, Bino; Janssen, Stijn

    2015-11-01

    Effects of vegetation on pollutant dispersion receive increased attention in attempts to reduce air pollutant concentration levels in the urban environment. In this study, we examine the influence of vegetation on the concentrations of traffic pollutants in urban street canyons using numerical simulations with the CFD code OpenFOAM. This CFD approach is validated against literature wind tunnel data of traffic pollutant dispersion in street canyons. The impact of trees is simulated for a variety of vegetation types and the full range of approaching wind directions at 15° interval. All these results are combined using meteo statistics, including effects of seasonal leaf loss, to determine the annual average effect of trees in street canyons. This analysis is performed for two pollutants, elemental carbon (EC) and PM10, using background concentrations and emission strengths for the city of Antwerp, Belgium. The results show that due to the presence of trees the annual average pollutant concentrations increase with about 8% (range of 1% to 13%) for EC and with about 1.4% (range of 0.2 to 2.6%) for PM10. The study indicates that this annual effect is considerably smaller than earlier estimates which are generally based on a specific set of governing conditions (1 wind direction, full leafed trees and peak hour traffic emissions).

  16. Impact of trees on pollutant dispersion in street canyons: A numerical study of the annual average effects in Antwerp, Belgium.

    Science.gov (United States)

    Vranckx, Stijn; Vos, Peter; Maiheu, Bino; Janssen, Stijn

    2015-11-01

    Effects of vegetation on pollutant dispersion receive increased attention in attempts to reduce air pollutant concentration levels in the urban environment. In this study, we examine the influence of vegetation on the concentrations of traffic pollutants in urban street canyons using numerical simulations with the CFD code OpenFOAM. This CFD approach is validated against literature wind tunnel data of traffic pollutant dispersion in street canyons. The impact of trees is simulated for a variety of vegetation types and the full range of approaching wind directions at 15° interval. All these results are combined using meteo statistics, including effects of seasonal leaf loss, to determine the annual average effect of trees in street canyons. This analysis is performed for two pollutants, elemental carbon (EC) and PM10, using background concentrations and emission strengths for the city of Antwerp, Belgium. The results show that due to the presence of trees the annual average pollutant concentrations increase with about 8% (range of 1% to 13%) for EC and with about 1.4% (range of 0.2 to 2.6%) for PM10. The study indicates that this annual effect is considerably smaller than earlier estimates which are generally based on a specific set of governing conditions (1 wind direction, full leafed trees and peak hour traffic emissions). PMID:26100726

  17. NO2 photolysis frequencies in street canyons

    Science.gov (United States)

    Koepke, P.; Garhammer, M.; Hess, M.; Roeth, E.-P.

    2010-08-01

    Photolysis frequencies for NO2 are modeled for the conditions in urban streets, which are taken into account as canyons with variable height and width. The effect of a street canyon is presented with absolute values and as a ratio RJ of the photolysis frequency within the street compared to that with free horizon. This allows further use of the existing photolysis parameterizations. Values are presented for variable solar elevation and azimuth angles, varying atmospheric conditions and different street properties. The NO2 photolysis frequency in a street depends strongly on the relative width of the street and its orientation towards the sun. Averaged over atmospheric conditions and street orientation, the NO2 photolysis frequency is reduced in comparison with the values for free horizon: to less than 20% for narrow skyscraper streets, to about 40% for typical urban streets, and only to about 80% for garden streets. A parameterization with the global solar irradiance is given for the averaged RJ values.

  18. NO2 photolysis frequencies in street canyons

    Directory of Open Access Journals (Sweden)

    E.-P. Roeth

    2010-05-01

    Full Text Available Photolysis frequencies for NO2 are modeled for the conditions in urban streets, which are taken into account as canyons with variable height and width. The effect of a street canyon is presented with absolute values and as a ratio RJ of the photolysis frequency within the street against those with free horizon, which allows further use of the existing photolysis parameterizations. Values are presented for variable solar elevation and azimuth angles, varying atmospheric conditions and different street properties. The NO2 photolysis frequency in the street, averaged over atmospheric conditions and street orientation, is reduced to less than 20% for narrow streets, to about 40% for typical urban streets, and only to about 80% for garden streets, each with about ±5% uncertainty. A parameterization of RJ with the global solar irradiance is given for values that are averaged over the meteorological conditions and the street orientation.

  19. “SHANGRI-LA” IN NUJIANG CANYON

    Institute of Scientific and Technical Information of China (English)

    李晓勤

    2004-01-01

    A few hours' drive took me to a place called Bingzhongluo,the largest piece of flatland in the canyon,where the Nujiang River takes two abrupt turns, forming the first bend on the Nujiang River,which is a best known scenic spot in China. At the side of the river there is a tablet of pure white marble inscribed with words painted in bright red,reading:“Bingzhongluo,the Shangri-La.”

  20. Numerical study on the ozone formation inside street canyons using a chemistry box model

    Institute of Scientific and Technical Information of China (English)

    Chun-Ho Liu; Dennis Y. C. Leung

    2008-01-01

    Tropospheric ozone is a secondary air pollutant produced in the presence of nitrogen oxides, volatile organic compounds (VOCs), and solar radiation. In an urban environment, ground-level vehicular exhaust is the major anthropogenic source of ozone precursors. In the cases of street canyons, pollutant dilution is weakened by the surrounding buildings that create localized high concentration of nitrogen oxides and VOCs, and thus leads to high potential of ozone formation. By considering the major physical and chemical processes, a chemistry box model is employed to investigate the characteristics of ozone formation due to vehicular exhaust inside street canyons under the worst case scenario, i.e. the calm wind condition. It is found that a high level of ozone concentration, of the order of 100 ppbv and higher, would occur inside the street canyons, in particular, when the emission rate (concentration) ratio of VOCs to nitrogen oxides is greater than 10. This elevated ozone concentration appears at the transition from VOCs to nitrogen oxides sensitivity and may extend to a few hundreds.

  1. California State Waters Map Series--Hueneme Canyon and vicinity, California

    Science.gov (United States)

    Johnson, Samuel Y.; Dartnell, Peter; Cochrane, Guy R.; Golden, Nadine E.; Phillips, Eleyne L.; Ritchie, Andrew C.; Kvitek, Rikk G.; Greene, H. Gary; Krigsman, Lisa M.; Endris, Charles A.; Clahan, Kevin B.; Sliter, Ray W.; Wong, Florence L.; Yoklavich, Mary M.; Normark, William R.

    2012-01-01

    In 2007, the California Ocean Protection Council initiated the California Seafloor Mapping Program (CSMP), designed to create a comprehensive seafloor map of high-resolution bathymetry, marine benthic habitats, and geology within the 3-nautical-mile limit of California's State Waters. The CSMP approach is to create highly detailed seafloor maps through collection, integration, interpretation, and visualization of swath sonar data, acoustic backscatter, seafloor video, seafloor photography, high-resolution seismic-reflection profiles, and bottom-sediment sampling data. The map products display seafloor morphology and character, identify potential marine benthic habitats, and illustrate both the surficial seafloor geology and shallow (to about 100 m) subsurface geology. The Hueneme Canyon and vicinity map area lies within the eastern Santa Barbara Channel region of the Southern California Bight. The area is part of the Western Transverse Ranges geologic province, which is north of the California Continental Borderland. Significant clockwise rotation - at least 90° - since the early Miocene has been proposed for the Western Transverse Ranges, and the region is presently undergoing north-south shortening. This geologically complex region forms a major biogeographic transition zone, separating the cold-temperate Oregonian province north of Point Conception from the warm-temperate California province to the south. The map area, which is offshore of the Oxnard plain and west of and along the trend of the south flank of the Santa Monica Mountains, lies at the east end of the Santa Barbara littoral cell, characterized by west-to-east littoral transport of sediment derived mainly from coastal watersheds. The Hueneme Canyon and vicinity map area in California's State Waters is characterized by two major physiographic features: (1) the nearshore continental shelf, and (2) the Hueneme and Mugu Submarine Canyon system, which, in the map area, includes Hueneme Canyon and parts

  2. The impacts of wind power integration on sub-daily variation in river flows downstream of hydroelectric dams.

    Science.gov (United States)

    Kern, Jordan D; Patino-Echeverri, Dalia; Characklis, Gregory W

    2014-08-19

    Due to their operational flexibility, hydroelectric dams are ideal candidates to compensate for the intermittency and unpredictability of wind energy production. However, more coordinated use of wind and hydropower resources may exacerbate the impacts dams have on downstream environmental flows, that is, the timing and magnitude of water flows needed to sustain river ecosystems. In this paper, we examine the effects of increased (i.e., 5%, 15%, and 25%) wind market penetration on prices for electricity and reserves, and assess the potential for altered price dynamics to disrupt reservoir release schedules at a hydroelectric dam and cause more variable and unpredictable hourly flow patterns (measured in terms of the Richards-Baker Flashiness (RBF) index). Results show that the greatest potential for wind energy to impact downstream flows occurs at high (∼25%) wind market penetration, when the dam sells more reserves in order to exploit spikes in real-time electricity prices caused by negative wind forecast errors. Nonetheless, compared to the initial impacts of dam construction (and the dam's subsequent operation as a peaking resource under baseline conditions) the marginal effects of any increased wind market penetration on downstream flows are found to be relatively minor.

  3. The impacts of wind power integration on sub-daily variation in river flows downstream of hydroelectric dams.

    Science.gov (United States)

    Kern, Jordan D; Patino-Echeverri, Dalia; Characklis, Gregory W

    2014-08-19

    Due to their operational flexibility, hydroelectric dams are ideal candidates to compensate for the intermittency and unpredictability of wind energy production. However, more coordinated use of wind and hydropower resources may exacerbate the impacts dams have on downstream environmental flows, that is, the timing and magnitude of water flows needed to sustain river ecosystems. In this paper, we examine the effects of increased (i.e., 5%, 15%, and 25%) wind market penetration on prices for electricity and reserves, and assess the potential for altered price dynamics to disrupt reservoir release schedules at a hydroelectric dam and cause more variable and unpredictable hourly flow patterns (measured in terms of the Richards-Baker Flashiness (RBF) index). Results show that the greatest potential for wind energy to impact downstream flows occurs at high (∼25%) wind market penetration, when the dam sells more reserves in order to exploit spikes in real-time electricity prices caused by negative wind forecast errors. Nonetheless, compared to the initial impacts of dam construction (and the dam's subsequent operation as a peaking resource under baseline conditions) the marginal effects of any increased wind market penetration on downstream flows are found to be relatively minor. PMID:25061693

  4. Long-term surveillance plan for the Burro Canyon disposal cell Slick Rock, Colorado

    International Nuclear Information System (INIS)

    This long-term surveillance plan (LTSP) describes the U.S. Department of Energy (DOE) long-term care program for the Uranium Mill Tailings Remedial Action (UMTRA) Project Burro Canyon disposal cell in San Miguel County, Colorado. The U.S. Nuclear Regulatory Commission (NRC) developed regulations for the issuance of a general license for the custody and long-term care of UMTRA Project disposal sites in 10 CFR Part 40. The purpose of this general license is to ensure that the UMTRA Project disposal sites are cared for in a manner that protects the public health and safety and the environment. Before each disposal site is licensed, the NRC requires the DOE to submit a site-specific LTSP. The DOE prepared this LTSP to meet this requirement for the Burro Canyon disposal cell. The general license becomes effective when the NRC concurs with the DOE's determination that remedial action is complete at the Burro Canyon disposal cell and the NRC formally accepts this LTSP. Attachment 1 contains the concurrence letters from NRC. This LTSP describes the long-term surveillance program the DOE has implemented to ensure that the Burro Canyon disposal cell performs as designed. The program is based on site inspections to identify threats to disposal cell integrity. Ground water monitoring will not be required at the Burro Canyon disposal cell because the ground water protection strategy is supplemental standards based on low yield from the uppermost aquifer. The LTSP is based on the UMTRA Project's long-term surveillance program guidance and meets the requirements of 10 CFR 40.27(b) and 40 CFR 192.03

  5. Holocene sedimentary activity in a non-terrestrially coupled submarine canyon: Cook Strait Canyon system, New Zealand

    Science.gov (United States)

    Mountjoy, J. J.; Micallef, A.; Stevens, C. L.; Stirling, M. W.

    2014-06-01

    The Cook Strait Canyon system, located between the North and South islands of New Zealand, is a large (1800 km2), multi-branching, shelf-indenting canyon on an active subduction margin. The canyon comes within 1 km of the coast, but does not intercept fluvial or littoral sediment systems and is therefore defined as a non-terrestrially coupled system. Sediment transport associated with a strong tidal stream, and seafloor disturbance related to numerous high-activity faults, is known from previous studies. Little is known, however, about the rates of sedimentary activity in the canyon and the processes driving it. A substantial dataset of EM300 multibeam bathymetry, gravity cores, 3.5 kHz seismic reflection profiles, camera and video transects and current meter data have been collected across the region between 2002 and 2011. The canyon system therefore provides an excellent study area for understanding sediment transport in a non-coupled submarine canyon system. Analysis of the data reveals a two-staged sediment transport system where: (1) oceanographic (tidal) processes mobilise sediment from the continental shelf and transport it to depocentres in the upper-central canyons, and (2) tectonic (earthquake) processes remobilise sediment that is transported through the lower canyon to the deep ocean. Tidal boundary-layer currents within the canyon reach velocities up to 0.53 m/s and are capable of mobilising fine sand in the central reach of the upper canyons. The velocity is higher at the canyon rim and capable of mobilising coarse sand. Sediment depocentres resulting from this tidally forced sediment transport have a well formed geomorphology within the mid-upper canyon arms of Cook Strait and Nicholson Canyons. Pseudo-static stability modelling, supported by sediment core analysis, indicates that sediment accumulated in the upper canyons fails during seismic events approximately every 100 years. The 100 year return period ground shaking-level (peak ground

  6. Impacts and Solutions of Wind Power Integration on Grids%风电并网对电网的影响分析及解决方案

    Institute of Scientific and Technical Information of China (English)

    刘开俊

    2012-01-01

    Along with the rapid growth of wind power since the Eleventh Five-Year, but disharmony problems between wind power and power grids gradually appear. In order to promote the sustainable development of wind power, based on lastest data and study results, considering the safe operation, consumptive needs and construction planning, the. impacts and causes of wind power integration on grids are analyzed. Some solutions are put forward in aspects of technology development, power source optimization, grid structure construction and overall planning, which could be a reference for the scientific and healthy development of power industry.%“十一五”以来我国风电规模快速增长,但风电与电网发展不协调.为更好地推动风电可持续发展及场网协调发展,基于最新数据和研究成果,从风电运行安全、消纳需求、规划建设等角度,分析风电并网对电网带来的影响和原因,从技术发展、电源优化、网架建设、统筹规划等方面,提出解决方案,为电力行业科学健康发展提供参考.

  7. 2009 weather and aeolian sand-transport data from the Colorado River corridor, Grand Canyon, Arizona

    Science.gov (United States)

    Draut, Amy E.; Sondossi, Hoda A.; Dealy, Timothy P.; Hazel, Joseph E., Jr.; Fairley, Helen C.; Brown, Christopher R.

    2010-01-01

    This report presents measurements of weather parameters and aeolian sand transport made in 2009 near selected archeological sites in the Colorado River corridor through Grand Canyon, Ariz. The quantitative methods and data discussed here form a basis for monitoring ecosystem processes that affect archeological-site stability. Combined with forthcoming work to evaluate landscape evolution at nearby archeological sites, these data can be used to document the relation between physical processes, including weather and aeolian sand transport, and their effects on the physical integrity of archeological sites. Data collected in 2009 reveal event- and seasonal-scale variations in rainfall, wind, temperature, humidity, and barometric pressure. Broad seasonal changes in aeolian sediment flux are also apparent at most study sites. Differences in weather patterns between 2008 and 2009 included an earlier spring windy season, greater spring precipitation even though 2009 annual rainfall totals were in general substantially lower than in 2008, and earlier onset of the reduced diurnal barometric-pressure fluctuations commonly associated with summer monsoon conditions. Weather patterns in middle to late 2009 were apparently affected by a transition of the ENSO cycle from a neutral phase to the El Ni?o phase. The continuation of monitoring that began in 2007, and installation of additional equipment at several new sites in early 2008, allowed evaluation of the effects of the March 2008 high-flow experiment (HFE) on aeolian sand transport. As reported earlier, at 2 of the 9 sites studied, spring and summer winds in 2008 reworked the HFE sandbars to form new aeolian dunes, where sand moved inland toward larger, well-established dune fields. Observations in 2009 showed that farther inland migration of the dune at one of those two sites is likely inhibited by vegetation. At the other location, the new aeolian dune form was found to have moved 10 m inland toward older, well

  8. Ascension Submarine Canyon, California - Evolution of a multi-head canyon system along a strike-slip continental margin

    Science.gov (United States)

    Nagel, D.K.; Mullins, H.T.; Greene, H. Gary

    1986-01-01

    Ascension Submarine Canyon, which lies along the strike-slip (transform) dominated continental margin of central California, consists of two discrete northwestern heads and six less well defined southeastern heads. These eight heads coalesce to form a single submarine canyon near the 2700 m isobath. Detailed seismic stratigraphic data correlated with 19 rock dredge hauls from the walls of the canyon system, suggest that at least one of the two northwestern heads was initially eroded during a Pliocene lowstand of sea level ???3.8 m.y. B.P. Paleogeographic reconstructions indicate that at this time, northwestern Ascension Canyon formed the distal channel of nearby Monterey Canyon and has subsequently been offset by right-lateral, strike-slip faulting along the San Gregorio fault zone. Some of the six southwestern heads of Ascension Canyon may also have been initially eroded as the distal portions of Monterey Canyon during late Pliocene-early Pleistocene sea-level lowstands (???2.8 and 1.75 m.y. B.P.) and subsequently truncated and offset to the northwest. There have also been a minimum of two canyon-cutting episodes within the past 750,000 years, after the entire Ascension Canyon system migrated to the northwest past Monterey Canyon. We attribute these late Pleistocene erosional events to relative lowstands of sea level 750,000 and 18,000 yrs B.P. The late Pleistocene and Holocene evolution of the six southeastern heads also appears to have been controlled by structural uplift of the Ascension-Monterey basement high at the southeastern terminus of the Outer Santa Cruz Basin. We believe that uplift of this basement high sufficiently oversteepened submarine slopes to induce gravitational instability and generate mass movements that resulted in the erosion of the canyon heads. Most significantly, though, our results and interpretations support previous proposals that submarine canyons along strike-slip continental margins can originate by tectonic trunction and lateral

  9. On the Improvement of Convergence Performance for Integrated Design of Wind Turbine Blade Using a Vector Dominating Multi-objective Evolution Algorithm

    Science.gov (United States)

    Wang, L.; Wang, T. G.; Wu, J. H.; Cheng, G. P.

    2016-09-01

    A novel multi-objective optimization algorithm incorporating evolution strategies and vector mechanisms, referred as VD-MOEA, is proposed and applied in aerodynamic- structural integrated design of wind turbine blade. In the algorithm, a set of uniformly distributed vectors is constructed to guide population in moving forward to the Pareto front rapidly and maintain population diversity with high efficiency. For example, two- and three- objective designs of 1.5MW wind turbine blade are subsequently carried out for the optimization objectives of maximum annual energy production, minimum blade mass, and minimum extreme root thrust. The results show that the Pareto optimal solutions can be obtained in one single simulation run and uniformly distributed in the objective space, maximally maintaining the population diversity. In comparison to conventional evolution algorithms, VD-MOEA displays dramatic improvement of algorithm performance in both convergence and diversity preservation for handling complex problems of multi-variables, multi-objectives and multi-constraints. This provides a reliable high-performance optimization approach for the aerodynamic-structural integrated design of wind turbine blade.

  10. Type IV Wind Turbine Model

    DEFF Research Database (Denmark)

    Hansen, Anca Daniela; Margaris, Ioannis D.

    This document is created as part of the EaseWind project. The goal of this project is to develop and investigate new control features for primary response provided by wind power plants. New control features as inertial response, synchronising power and power system damping are of interest to EaseWind...... project to be incorporated in the wind power plant level. This document describes the Type 4 wind turbine simulation model, implemented in the EaseWind project. The implemented wind turbine model is one of the initial necessary steps toward integrating new control services in the wind power plant level....... In the project, this wind turbine model will be further incorporated in a wind power plant model together with the implementation in the wind power control level of the new control functionalities (inertial response, synchronising power and power system damping). For this purpose an aggregate wind power plant...

  11. Wind Tunnel Measurements of Turbulent Boundary Layer over Hypothetical Urban Roughness Elements

    Science.gov (United States)

    Ho, Y. K.; Liu, C. H.

    2012-04-01

    Urban morphology affects the near-ground atmospheric boundary layer that in turn modifies the wind flows and pollutant dispersion over urban areas. A number of numerical models (large-eddy simulation, LES and k-ɛ turbulence models) have been developed to elucidate the transport processes in and above urban street canyons. To complement the modelling results, we initiated a wind tunnel study to examine the influence of idealized urban roughness on the flow characteristics and pollutant dispersion mechanism over 2D idealized street canyons placed in cross flows. Hot-wire anemometry (HWA) was employed in this study to measure the flows over 2D street canyons in the wind tunnel in our university. Particular focus in the beginning stage was on the fabrication of hot-wire probes, data acquisition system, and signal processing technique. Employing the commonly adopted hot-wire universal function, we investigated the relationship in between and developed a scaling factor which could generalize the output of our hot-wire probes to the standardized one as each hot-wire probes has its unique behaviour. Preliminary experiments were performed to measure the wind flows over street canyons of unity aspect ratio. Vertical profiles of the ensemble average velocity and fluctuations at three different segments over the street canyons were collected. The results were then compared with our LES that show a good argument with each other. Additional experiments are undertaken to collect more data in order to formulate the pollutant dispersion mechanism of street canyons and urban areas.

  12. Large eddy simulation of pollutant gas dispersion with buoyancy ejected from building into an urban street canyon.

    Science.gov (United States)

    Hu, L H; Xu, Y; Zhu, W; Wu, L; Tang, F; Lu, K H

    2011-09-15

    The dispersion of buoyancy driven smoke soot and carbon monoxide (CO) gas, which was ejected out from side building into an urban street canyon with aspect ratio of 1 was investigated by large eddy simulation (LES) under a perpendicular wind flow. Strong buoyancy effect, which has not been revealed before, on such pollution dispersion in the street canyon was studied. The buoyancy release rate was 5 MW. The wind speed concerned ranged from 1 to 7.5m/s. The characteristics of flow pattern, distribution of smoke soot and temperature, CO concentration were revealed by the LES simulation. Dimensionless Froude number (Fr) was firstly introduced here to characterize the pollutant dispersion with buoyancy effect counteracting the wind. It was found that the flow pattern can be well categorized into three regimes. A regular characteristic large vortex was shown for the CO concentration contour when the wind velocity was higher than the critical re-entrainment value. A new formula was theoretically developed to show quantitatively that the critical re-entrainment wind velocities, u(c), for buoyancy source at different floors, were proportional to -1/3 power of the characteristic height. LES simulation results agreed well with theoretical analysis. The critical Froude number was found to be constant of 0.7. PMID:21216525

  13. Implementation of wind power plants and photovoltaic power plants in a smart Grid by means of communication standards; Integration von Wind- und Photovoltaikanlagen in ein Smart Grid durch die Anwendeung von Kommunikationsstandards

    Energy Technology Data Exchange (ETDEWEB)

    Struebbe, Kai [TUeV SUeD AG, Muenchen (Germany). Embedded Systems; Weber, Karl [ZHAW Institute of Embedded Systems, Winterthur (Switzerland)

    2012-07-01

    Energy supply from wind turbines and photovoltaic panels is obviously volatile as the resource cannot provide a stable supply. The medium voltage and low voltage grids can hardly cope with that situation. The integration of renewable energy resources requires additional effort beyond the regulations of power generation connection in VDE 4105 or BDEW-Guideline. Grid operators and the federal authorities (Renewable Energy Law - EEG) have to set up additional requirements regarding the communication capabilities of devices and plants. The proof of compliance with the communication standard IEC 61850 will be an important precondition for further development and additional funding according to EEG. The presentation shows the current regulations for device manufacturer and plant operator and the possible infrastructure for the next integration steps. (orig.)

  14. A vertical/horizontal integration wind-induced circulation model (VH13D): A method for including surface and bottom logarithmic profiles

    Science.gov (United States)

    Wu, Jian; Tsanis, Ioannis K.

    A three-dimensional model called VH13D is developed using the vertical/horizontal integration (VHI) approach. The double-logarithmic velocity profile including both the surface and bottom sublayer characteristic lengths is employed to accurately evaluate the bottom shear stress and depth-averaged advective terms. The model is verified using analytical solutions and laboratory data for shear-induced countercurrent flows and is compared with other two- and three-dimensional circulation models in a simplified basin. It is demonstrated that the newly developed model improves the conventional two-dimensional depth-averaged and Quasi-3D models and provides a new approach to the three-dimensional wind-induced circulation model. It can efficiently simulate the wind-induced 3D current structure in lakes and estuaries under isothermal conditions.

  15. Plug-in hybrid electric vehicles as a way to maximize the integration of variable renewable energy in power systems: The case of wind generation in northeastern Brazil

    International Nuclear Information System (INIS)

    Several studies have proposed different tools for analyzing the integration of variable renewable energy into power grids. This study applies an optimization tool to model the expansion of the electric power system in northeastern Brazil, enabling the most efficient dispatch of the variable output of the wind farms that will be built in the region over the next 20 years. The expected combined expansion of wind generation with conventional inflexible generation facilities, such as nuclear plants and run-of-the-river hydropower plants, poses risks of future mismatch between supply and demand in northeastern Brazil. Therefore, this article evaluates the possibility of using a fleet of plug-in hybrid electric vehicles (PHEVs) to regularize possible energy imbalances. Findings indicate that a dedicated fleet of 500 thousand PHEVs in 2015, and a further 1.5 million in 2030, could be recharged overnight to take advantage of the surplus power generated by wind farms. To avoid the initial costs of smart grids, this article suggests, as a first step, the use of a governmental PHEV fleet that allows fleet managers to control battery charging times. Finally, the study demonstrates the advantages of optimizing simultaneously the power and transport sectors to test the strategy suggested here. -- Highlights: ► We evaluated the use of plug-in hybrid electric vehicles (PHEV) to regularize possible energy imbalances in northeastern Brazil. ► This imbalance might result from the large-scale wind power penetration along with conventional inflexible power plants in the region. ► We adapted the MESSAGE optimization tool to the base conditions of the Brazilian power system. ► 500 thousand PHEVs in 2015 and 1.5 million in 2030 could be recharged taking advantage of wind energy surplus.

  16. Reconstructing Holocene changes in the Southern Hemisphere westerly winds: Integrating modern processes and paleoclimate data from New Zealand's southern fjords

    Science.gov (United States)

    Hinojosa, J.; Moy, C. M.; Wilson, G. S.; Stirling, C. H.

    2013-12-01

    The Southern Hemisphere westerly winds are an important component of the global carbon cycle due to their influence on Southern Ocean CO2 flux. In addition, the winds influence mid-latitude storm tracks, thereby controlling moisture balance over much of New Zealand's South Island and other Southern Hemisphere regions. Fiordland, New Zealand is an ideal locale to investigate Holocene changes in westerly wind behavior: It sits at the northern margin of the wind field maximum, is sensitive to latitudinal and strength fluctuations of the winds, and is the location of numerous fjord sub-basins with high sedimentation rates (up to 3 mm/yr). Due to the strong positive relationship between wind speed and regional rainfall, reconstructions of past precipitation and fjord circulation can inform us of past westerly wind behavior. These processes can be observed through changes in the rate of organic carbon delivery from land: When precipitation is high, more terrestrial organic carbon is delivered to the fjords, while low precipitation shifts the balance toward accumulation of marine organic carbon. An important first step towards reconstructing past westerly wind variability is to characterize the distribution and cycling of carbon throughout different depositional settings in the fjords to determine the optimal location for the development of paleoclimate records. Here, we present a geochemical characterization of surface sediments and the water column throughout the region and apply this understanding to sediment cores. During three field seasons in 2012 and 2013, we collected surface sediments, particulate organic matter, and piston cores from 10 different fjords spanning 44-46° S. Our results suggest that organic carbon in the fjord basins largely follows a two-end-member mixing model, drawing from marine and terrestrial end-member sources. We see consistent down-fjord trends in carbon and nitrogen concentrations and isotopes measured from surface sediments and

  17. On the Integration of Wind and Solar Energy to Provide a Total Energy Supply in the U.S

    Science.gov (United States)

    Liebig, E. C.; Rhoades, A.; Sloggy, M.; Mills, D.; Archer, C. L.

    2009-12-01

    This study examines the feasibility of using renewable energy - mostly wind and solar radiation - as the primary sources of energy in the U.S., under the assumption that a nationwide electric transmission grid is in place. Previous studies have shown that solar output from California and Texas using energy storage is well correlated with the state energy load on an hour by hour basis throughout the year and with the US national load on a monthly basis. Other studies have shown that solar or wind alone can power the present US grid on average. This study explores scenarios for use of wind and solar energy together at the national scale on an hour by hour basis to determine if such a combination is a better match to national seasonal load scenarios than either of the two alone on an hour-by-hour basis. Actual hour by hour national load data from a particular year will be used as a basis, with some scenarios incorporating vehicle sector electrification and building heating and cooling using electric heat pumps. Hydro and geothermal generation can provide additional controllable output, when needed, to fulfill the hourly electricity and/or energy needs. Hourly wind speed data were calculated at the hub height of 80 m above the ground for the year 2006 at over 150 windy locations in the continental US using an extrapolation technique based on 10-m wind speed measurements and vertical sounding profiles. Using a 1.5 MW wind turbine as benchmark, the hourly wind power production nationwide was determined at all locations. Similarly, the hourly output from solar plants, with and without thermal storage, was calculated based on Ausra’s model assuming that the solar production would occur in the Southwest, the area with the greatest solar radiation density in the U.S. Hourly electricity demand for the year 2006 was obtained nationwide from a variety of sources, including the Federal Energy Regulation Commission. Hourly residential heating and cooking, industrial heat

  18. Non-cooperation Game Analysis of Wind Power Integration%风电并网过程中的非合作博弈分析

    Institute of Scientific and Technical Information of China (English)

    王晓天

    2015-01-01

    针对当前风电并网困难问题,综合考虑常规能源发电企业、风电企业、电网企业与政府之间的相互关系,根据非合作博弈理论进行分析,结果证明:风电并网困难问题的解决归根结底取决于风电发展规模的大小;政府对电网企业允许或不允许风电并网的行为进行补贴或处罚,取决于“弃风”量的大小和电网改造升级的成本高低,并且无论补贴或是处罚对社会福利的影响都是等效的;当“弃风”量达到一定程度时,电网企业对电网的改造升级将由被动转为主动。%In view of existing problems in the grid-connected wind power,this paper makes an analysis on the difficult problems of the wind power integration using non-cooperative game theory,considering the mutual relations between the conventional energy power enterprises,wind power enterprises,power grid enterprises,and the govern-ment. The result shows that the solution depends on the size of wind power development,the government's subsidies or punishment toward the action whether power grid enterprises permit the grid-connection of wind power or not,de-pending on the amount of abandoned wind and the cost of upgrading power grids,the impacts of subsidies or punish-ment on social welfare are equivalent. When the amount of abandoned wind reaches a certain level,power grid enter-prises will turn active from being passive to upgrade their power grids.

  19. 78 FR 7810 - Glen Canyon Dam Adaptive Management Work Group

    Science.gov (United States)

    2013-02-04

    ... Bureau of Reclamation Glen Canyon Dam Adaptive Management Work Group AGENCY: Bureau of Reclamation, Interior. ACTION: Notice of public meeting. SUMMARY: The Glen Canyon Dam Adaptive Management Work Group.... L. 102-575) of 1992. The AMP includes a Federal advisory committee, the AMWG, a technical work...

  20. 76 FR 24516 - Glen Canyon Dam Adaptive Management Work Group

    Science.gov (United States)

    2011-05-02

    ... Bureau of Reclamation Glen Canyon Dam Adaptive Management Work Group AGENCY: Bureau of Reclamation, Interior. ACTION: Notice of public meeting. SUMMARY: The Glen Canyon Dam Adaptive Management Work Group...-575) of 1992. The AMP includes a Federal advisory committee, the AMWG, a technical work group (TWG),...

  1. 75 FR 34476 - Glen Canyon Dam Adaptive Management Work Group

    Science.gov (United States)

    2010-06-17

    ... Bureau of Reclamation Glen Canyon Dam Adaptive Management Work Group AGENCY: Bureau of Reclamation... Interior (Secretary) is renewing the charter for the Glen Canyon Dam Adaptive Management Work Group. The purpose of the Adaptive Management Work Group is to advise and to provide recommendations to the...

  2. 36 CFR 7.4 - Grand Canyon National Park.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Grand Canyon National Park. 7.4 Section 7.4 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR SPECIAL REGULATIONS, AREAS OF THE NATIONAL PARK SYSTEM § 7.4 Grand Canyon National Park. (a)...

  3. Case Study of Integrating an Offshore Wind Farm with Offshore Oil and Gas Platforms and with an Onshore Electrical Grid

    Directory of Open Access Journals (Sweden)

    Wei He

    2013-01-01

    Full Text Available This research project explored the technical feasibility of utilizing an offshore wind farm as a supplementary power source to several electrical grids of offshore oil and gas platforms and providing surplus power to an onshore grid. Three case studies comprising wind farms rated at 20 MW, 100 MW, and 1000 MW have been studied with the focus on (i the operation benefits of CO2/NOx emission reduction, (ii the electrical grid stability, and (iii the technical implementation feasibility. The proposed 20 MW, 100 MW, and 1000 MW wind farm cases are theoretically feasible in terms of the selected technical criteria, although further detailed design operational studies, and economical analysis are required.

  4. Big Canyon Creek Ecological Restoration Strategy.

    Energy Technology Data Exchange (ETDEWEB)

    Rasmussen, Lynn; Richardson, Shannon

    2007-10-01

    He-yey, Nez Perce for steelhead or rainbow trout (Oncorhynchus mykiss), are a culturally and ecologically significant resource within the Big Canyon Creek watershed; they are also part of the federally listed Snake River Basin Steelhead DPS. The majority of the Big Canyon Creek drainage is considered critical habitat for that DPS as well as for the federally listed Snake River fall chinook (Oncorhynchus tshawytscha) ESU. The Nez Perce Soil and Water Conservation District (District) and the Nez Perce Tribe Department of Fisheries Resources Management-Watershed (Tribe), in an effort to support the continued existence of these and other aquatic species, have developed this document to direct funding toward priority restoration projects in priority areas for the Big Canyon Creek watershed. In order to achieve this, the District and the Tribe: (1) Developed a working group and technical team composed of managers from a variety of stakeholders within the basin; (2) Established geographically distinct sub-watershed areas called Assessment Units (AUs); (3) Created a prioritization framework for the AUs and prioritized them; and (4) Developed treatment strategies to utilize within the prioritized AUs. Assessment Units were delineated by significant shifts in sampled juvenile O. mykiss (steelhead/rainbow trout) densities, which were found to fall at fish passage barriers. The prioritization framework considered four aspects critical to determining the relative importance of performing restoration in a certain area: density of critical fish species, physical condition of the AU, water quantity, and water quality. It was established, through vigorous data analysis within these four areas, that the geographic priority areas for restoration within the Big Canyon Creek watershed are Big Canyon Creek from stream km 45.5 to the headwaters, Little Canyon from km 15 to 30, the mainstem corridors of Big Canyon (mouth to 7km) and Little Canyon (mouth to 7km). The District and the Tribe

  5. Failure of Tapo Canyon Tailings Dam

    OpenAIRE

    Harder, Leslie F Jr; Stewart, Jonathan P.

    1996-01-01

    The failure of the Tapo Canyon tailings dam was one of the most striking failures of an earth structure to result from the January 17, 1994 Northridge, California earthquake. The failure involved a 60-m-wide breach of a tailings dam with a maximum height of 24 m, and 60 and 90 m downstream displacements of two sections of the dam. The failure resulted from liquefaction of the impounded tailings and possibly of the embankment materials. A significant volume of liquefied tailings passed through...

  6. The Black Canyon of the Gunnison: Today and Yesterday

    Science.gov (United States)

    Hansen, Wallace R.

    1965-01-01

    Since the early visit of Captain John William Gunnison in the middle of the last century, the Black Canyon of the Gunnison has stirred mixed apprehension and wonder in the hearts of its viewers. It ranks high among the more awesome gorges of North America. Many great western canyons are as well remembered for their brightly colored walls as for their airy depths. Not so the Black Canyon. Though it is assuredly not black, the dark-gray tones of its walls and the hazy shadows of its gloomy depths join together to make its name well deserved. Its name conveys an impression, not a picture. After the first emotional impact of the canyon, the same questions come to the minds of most reflective viewers and in about the following order: How deep is the Black Canyon, how wide, how does it compare with other canyons, what are the rocks, how did it form, and how long did it take? Several western canyons exceed the Black Canyon in overall size. Some are longer; some are deeper; some are narrower; and a few have walls as steep. But no other canyon in North American combines the depth, narrowness, sheerness, and somber countenance of the Black Canyon. In many places the Black Canyon is as deep as it is wide. Between The Narrows and Chasm View in the Black Canyon of the Gunnison National Monument (fig. 15) it is much deeper than wide. Average depth in the monument is about 2,000 feet, ranging from a maximum of about 2,700 feet, north of Warner Point (which also is the greatest depth anywhere in the canyon), to a minimum of about 1,750 feet at The Narrows. The stretch of canyon between Pulpit Rock and Chasm View, including The Narrows, though the shallowest in the monument, is also the narrowest, has some of the steepest walls, and is, therefore, among the most impressive segments of the canyon (fig. 3). Profiles of several well-known western canyons are shown in figure 1. Deepest of these by far is Hells Canyon of the Snake, on the Idaho-Oregon border. Clearly, it dwarfs the

  7. Hanging canyons of Haida Gwaii, British Columbia, Canada: Fault-control on submarine canyon geomorphology along active continental margins

    Science.gov (United States)

    Harris, Peter T.; Barrie, J. Vaughn; Conway, Kim W.; Greene, H. Gary

    2014-06-01

    Faulting commonly influences the geomorphology of submarine canyons that occur on active continental margins. Here, we examine the geomorphology of canyons located on the continental margin off Haida Gwaii, British Columbia, that are truncated on the mid-slope (1200-1400 m water depth) by the Queen Charlotte Fault Zone (QCFZ). The QCFZ is an oblique strike-slip fault zone that has rates of lateral motion of around 50-60 mm/yr and a small convergent component equal to about 3 mm/yr. Slow subduction along the Cascadia Subduction Zone has accreted a prism of marine sediment against the lower slope (1500-3500 m water depth), forming the Queen Charlotte Terrace, which blocks the mouths of submarine canyons formed on the upper slope (200-1400 m water depth). Consequently, canyons along this margin are short (4-8 km in length), closely spaced (around 800 m), and terminate uniformly along the 1400 m isobath, coinciding with the primary fault trend of the QCFZ. Vertical displacement along the fault has resulted in hanging canyons occurring locally. The Haida Gwaii canyons are compared and contrasted with the Sur Canyon system, located to the south of Monterey Bay, California, on a transform margin, which is not blocked by any accretionary prism, and where canyons thus extend to 4000 m depth, across the full breadth of the slope.

  8. Integration of a Wind Turbine Based Doubly Fed Induction Generator Using STATCOM and CROWBAR for Transient Stability Improvement

    Directory of Open Access Journals (Sweden)

    Bhupendra kumar

    2015-07-01

    Full Text Available Wind power stations mostly placed in remote areas; so they are characterized by weak grids and are often submitted to power system disturbance like faults, voltage sag etc. In this paper the crowbar protection method is used to ride through voltage sags and STATCOM is used to quickly sense the voltage sag and overcome it. The behavior of these machines during grid failure is an important issue. DFIG consists of a common induction generator with slip ring and a partial scale power electronic converter. Indirect field oriented controller is applied to rotor side converter for active power control and voltage regulation of wind turbine. On grid side PQ control scheme is applied. Wind turbine and its control units are described in details and also for STATCOM control. All power system components are simulated in MATLAB/ SIMULINK software. For studying the performance of controller, different abnormal conditions are applied even the worst case. Simulation results prove that the performance of STATCOM and DFIG control schemes as improving power quality and stability of wind turbine.

  9. Stochastic backscatter modelling for the prediction of pollutant removal from an urban street canyon: A large-eddy simulation

    Science.gov (United States)

    O'Neill, J. J.; Cai, X.-M.; Kinnersley, R.

    2016-10-01

    The large-eddy simulation (LES) approach has recently exhibited its appealing capability of capturing turbulent processes inside street canyons and the urban boundary layer aloft, and its potential for deriving the bulk parameters adopted in low-cost operational urban dispersion models. However, the thin roof-level shear layer may be under-resolved in most LES set-ups and thus sophisticated subgrid-scale (SGS) parameterisations may be required. In this paper, we consider the important case of pollutant removal from an urban street canyon of unit aspect ratio (i.e. building height equal to street width) with the external flow perpendicular to the street. We show that by employing a stochastic SGS model that explicitly accounts for backscatter (energy transfer from unresolved to resolved scales), the pollutant removal process is better simulated compared with the use of a simpler (fully dissipative) but widely-used SGS model. The backscatter induces additional mixing within the shear layer which acts to increase the rate of pollutant removal from the street canyon, giving better agreement with a recent wind-tunnel experiment. The exchange velocity, an important parameter in many operational models that determines the mass transfer between the urban canopy and the external flow, is predicted to be around 15% larger with the backscatter SGS model; consequently, the steady-state mean pollutant concentration within the street canyon is around 15% lower. A database of exchange velocities for various other urban configurations could be generated and used as improved input for operational street canyon models.

  10. System Integration of the Horizontal-Axis Wind Turbine: The Design of Turbine Blades with an Axial-Flux Permanent Magnet Generator

    Directory of Open Access Journals (Sweden)

    Chi-Jeng Bai

    2014-11-01

    Full Text Available In designing a horizontal-axis wind turbine (HAWT blade, system integration between the blade design and the performance test of the generator is important. This study shows the aerodynamic design of a HAWT blade operating with an axial-flux permanent magnet (AFPM generator. An experimental platform was built to measure the performance curves of the AFPM generator for the purpose of designing the turbine blade. An in-house simulation code was developed based on the blade element momentum (BEM theory and was used to lay out the geometric shape of the turbine blade, including the pitch angle and chord length at each section. This simulation code was combined with the two-dimensional (2D airfoil data for predicting the aerodynamic performance of the designed blades. In addition, wind tunnel experiments were performed to verify the simulation results for the various operating conditions. By varying the rotational speeds at four wind speeds, the experimental and simulation results for the mechanical torques and powers presented good agreement. The mechanical power of the system, which maximizes at the best operating region, provided significant information for designing the HAWT blade.

  11. On the integration of wind and solar energy to provide a total energy supply in the USA

    Science.gov (United States)

    Archer, Cristina; Mills, David; Cheng, Weili; Sloggy, Matthew; Liebig, Edwin; Rhoades, Alan

    2010-05-01

    This study examines the feasibility of using renewable energy - mostly wind and solar radiation - as the primary source of energy in the USA, under the assumption that a nationwide electric transmission grid is in place. Previous studies have shown that solar or wind alone can power the present U.S. grid on average. Other studies have shown that solar output from California and Texas using energy storage is well correlated with the state energy load on an hour by hour basis throughout the year and with the U.S. national load on a monthly basis. This study explores scenarios for use of wind and solar energy together at the national scale on an hour by hour basis to determine if such a combination is a better match to national seasonal load scenarios than either of the two alone on an hour-by-hour basis. Actual hour by hour national load data from the year 2006 are used as a basis, with some scenarios incorporating vehicle sector electrification and building heating and cooling using electric heat pumps. Hourly wind speed data were calculated at the hub height of 80 m above the ground for the year 2006 at over 150 windy locations in the continental U.S. using an extrapolation technique based on 10-m wind speed measurements and vertical sounding profiles. Using a 1.5 MW wind turbine as benchmark, the hourly wind power production nationwide was determined at all suitable locations. Similarly, the hourly output from solar plants, with and without thermal storage, was calculated based on Ausra's model assuming that the solar production would occur in the Southwest, the area with the greatest solar radiation density in the U.S. Hourly electricity demand for the year 2006 was obtained nationwide from a variety of sources, including the Federal Energy Regulation Commission. Hourly residential heating and cooking, industrial heat processing, and future electrified transportation loads were calculated from monthly and yearly energy consumption data from the Energy Information

  12. NO2 photolysis frequencies in street canyons

    Directory of Open Access Journals (Sweden)

    E.-P. Roeth

    2010-08-01

    Full Text Available Photolysis frequencies for NO2 are modeled for the conditions in urban streets, which are taken into account as canyons with variable height and width. The effect of a street canyon is presented with absolute values and as a ratio RJ of the photolysis frequency within the street compared to that with free horizon. This allows further use of the existing photolysis parameterizations. Values are presented for variable solar elevation and azimuth angles, varying atmospheric conditions and different street properties. The NO2 photolysis frequency in a street depends strongly on the relative width of the street and its orientation towards the sun. Averaged over atmospheric conditions and street orientation, the NO2 photolysis frequency is reduced in comparison with the values for free horizon: to less than 20% for narrow skyscraper streets, to about 40% for typical urban streets, and only to about 80% for garden streets. A parameterization with the global solar irradiance is given for the averaged RJ values.

  13. An Innovative Technique for Evaluating the Integrity and Durability of Wind Turbine Blade Composites - Final Project Report

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jy-An John [ORNL; Ren, Fei [ORNL; Tan, Ting [ORNL; Mandell, John [Montana State University; Agastra, Pancasatya [Montana State University

    2011-11-01

    To build increasingly larger, lightweight, and robust wind turbine blades for improved power output and cost efficiency, durability of the blade, largely resulting from its structural composites selection and aerodynamic shape design, is of paramount concern. The safe/reliable operation of structural components depends critically on the selection of materials that are resistant to damage and failure in the expected service environment. An effective surveillance program is also necessary to monitor the degradation of the materials in the course of service. Composite materials having high specific strength/stiffness are desirable for the construction of wind turbines. However, most high-strength materials tend to exhibit low fracture toughness. That is why the fracture toughness of the composite materials under consideration for the manufacture of the next generation of wind turbines deserves special attention. In order to achieve the above we have proposed to develop an innovative technology, based on spiral notch torsion test (SNTT) methodology, to effectively investigate the material performance of turbine blade composites. SNTT approach was successfully demonstrated and extended to both epoxy and glass fiber composite materials for wind turbine blades during the performance period. In addition to typical Mode I failure mechanism, the mixed-mode failure mechanism induced by the wind turbine service environments and/or the material mismatch of the composite materials was also effectively investigated using SNTT approach. The SNTT results indicate that the proposed protocol not only provides significant advance in understanding the composite failure mechanism, but also can be readily utilized to assist the development of new turbine blade composites.

  14. California State Waters Map Series—Monterey Canyon and vicinity, California

    Science.gov (United States)

    Dartnell, Peter; Maier, Katherine L.; Erdey, Mercedes D.; Dieter, Bryan E.; Golden, Nadine E.; Johnson, Samuel Y.; Hartwell, Stephen R.; Cochrane, Guy R.; Ritchie, Andrew C.; Finlayson, David P.; Kvitek, Rikk G.; Sliter, Ray W.; Greene, H. Gary; Davenport, Clifton W.; Endris, Charles A.; Krigsman, Lisa M.; Dartnell, Peter; Cochran, Susan A.

    2016-06-10

    IntroductionIn 2007, the California Ocean Protection Council initiated the California Seafloor Mapping Program (CSMP), designed to create a comprehensive seafloor map of high-resolution bathymetry, marine benthic habitats, and geology within the 3-nautical-mile limit of California’s State Waters. The CSMP approach is to create highly detailed seafloor maps through collection, integration, interpretation, and visualization of swath bathymetry data, acoustic backscatter, seafloor video, seafloor photography, high-resolution seismic-reflection profiles, and bottom-sediment sampling data. The map products display seafloor morphology and character, identify potential marine benthic habitats, and illustrate both the surficial seafloor geology and shallow subsurface geology.The Monterey Canyon and Vicinity map area lies within Monterey Bay in central California. Monterey Bay is one of the largest embayments along the west coast of the United States, spanning 36 km from its northern to southern tips (in Santa Cruz and Monterey, respectively) and 20 km along its central axis. Not only does it contain one of the broadest sections of continental shelf along California’s coast, it also contains Monterey Canyon, one of the largest and deepest submarine canyons in the world. Note that the California’s State Waters limit extends farther offshore between Santa Cruz and Monterey so that it encompasses all of Monterey Bay.The coastal area within the map area is lightly populated. The community of Moss Landing (population, 204) hosts the largest commercial fishing fleet in Monterey Bay in its harbor. The map area also includes parts of the cities of Marina (population, about 20,000) and Castroville (population, about 6,500). Fertile lowlands of the Salinas River and Pajaro River valleys largely occupy the inland part of the map area, and land use is primarily agricultural.The offshore part of the map area lies completely within the Monterey Bay National Marine Sanctuary. The

  15. Urban Wind Energy

    DEFF Research Database (Denmark)

    Beller, Christina

    for the installation of wind turbines in cities, with Copenhagen, DK, as example. Focus is taken on turbine with a swept area of maximum 5m2, since turbines of this size are relatively easy to be integrated in the urban space and are in the financial range for small companies as well as for private persons. Elements...... are expected. Therefore, methods are developed in this work to estimate the wind energy in cities depending on the built-up character, with both, simple and advanced calculation models. The energy produced by a wind turbine is also dependent on the turbine design, but especially on the rotor design...... important for the implementation of wind energy conversion systems are the macro and micro wind climate, the siting within a micro wind climate and the choice of a wind turbine model most appropriate for the selected site. In the frame of this work, all these important elements are analyzed and a row...

  16. CO2 absorption/emission and aerodynamic effects of trees on the concentrations in a street canyon in Guangzhou, China

    International Nuclear Information System (INIS)

    In this paper, the effects of trees on CO2 concentrations in a street canyon in Guangzhou, China are examined by Computational Fluid Dynamics (CFD) simulations of the concentration distribution, taking into account both the CO2 absorption/emission and aerodynamic effects of trees. Simulation results show that, under a 2 m/s southerly prevailing wind condition, CO2 absorption by trees will reduce the CO2 concentration by around 2.5% in the daytime and at the same time the trees' resistance will increase the difference of CO2 concentrations in the street and at the inflow by 43%. As the traffic density increases to 50 vehicles/min, the effect of trees on the ambient CO2 concentration will change from positive to negative. At night, trees have a negative effect on the concentration in the street canyon mainly because of their resistance to airflow. When environmental wind changes, the effect of trees will be different. -- Highlights: ► The trees affect CO2 concentrations in a street canyon. ► Both the CO2 absorption and flow resistance of trees are significant factors by day. ► As the emissions of CO2 increase, the effect of trees will become negative. ► At night, trees have a negative effect on CO2 concentration due to the resistance. -- The effects of trees on CO2 concentrations in a street canyon are examined by CFD simulations, taking into account both the CO2 absorption/emission and aerodynamic effects of trees

  17. Wind Integration into Energy Systems with a High Share of Nuclear Power—What Are the Compromises?

    OpenAIRE

    Behnam Zakeri; Samuli Rinne; Sanna Syri

    2015-01-01

    Towards low-carbon energy systems, there are countries with ongoing plans for expanding their nuclear power capacity, and simultaneously advancing the role of variable renewable energy sources (RES), namely wind and solar energy. This crossroads of capital-intensive, baseload power production and uncontrollable, intermittent RES may entail new challenges in the optimal and economic operation of power systems. This study examines this case by hourly analysis of a national-level energy system w...

  18. Optimal Power Management of a DISCO with Integrations of Reliability Considerations and Wind Farm Based on Benders Decomposition

    OpenAIRE

    Saidian, A.; S. S. Mortazavi; Baghdadi, M.

    2011-01-01

    This paper presents a comprehensive framework model of a distribution company with security and reliability considerations. A probabilistic wind farm, which is a renewable energy resource, is modeled in this work. The requirement energy of distribution company can be either provided by distribution company's own distributed generations or purchased from power market. Two reliability indices as well as DC load flow equations are also considered in order to satisfy reliability and security cons...

  19. Costs for integrating wind into the future ERCOT system with related costs for savings in CO2 emissions.

    Science.gov (United States)

    Lu, Xi; McElroy, Michael B; Sluzas, Nora A

    2011-04-01

    Wind power can make an important contribution to the goal of reducing emissions of CO2. The major problem relates to the intrinsic variability of the source and the difficulty of reconciling the supply of electricity with demand particularly at high levels of wind penetration. This challenge is explored for the case of the ERCOT system in Texas. Demand for electricity in Texas is projected to increase by approximately 60% by 2030. Considering hourly load data reported for 2006, assuming that the pattern of demand in 2030 should be similar to 2006, and adopting as a business as usual (BAU) reference an assumption that the anticipated additional electricity should be supplied by a combination of coal and gas with prices, discounted to 2007 dollars of $2 and $6 per MMBTU respectively, we conclude that the bus-bar price for electricity would increase by about 1.1 ¢/kWh at a wind penetration level of 30%, by about 3.4 ¢/kWh at a penetration level of 80%. Corresponding costs for reductions in CO2 range from $20/ton to $60/ton. A number of possibilities are discussed that could contribute to a reduction in these costs including the impact of an expanded future fleet of electrically driven vehicles.

  20. Lessons Learned from the Deployment and Integration of a Microwave Sounder Based Tropical Cyclone Intensity and Surface Wind Estimation Algorithm into NOAA/NESDIS Satellite Product Operations

    Science.gov (United States)

    Longmore, S. P.; Knaff, J. A.; Schumacher, A.; Dostalek, J.; DeMaria, R.; Chirokova, G.; Demaria, M.; Powell, D. C.; Sigmund, A.; Yu, W.

    2014-12-01

    The Colorado State University (CSU) Cooperative Institute for Research in the Atmosphere (CIRA) has recently deployed a tropical cyclone (TC) intensity and surface wind radii estimation algorithm that utilizes Suomi National Polar-orbiting Partnership (S-NPP) satellite Advanced Technology Microwave Sounder (ATMS) and Advanced Microwave Sounding Unit (AMSU) from the NOAA18, NOAA19 and METOPA polar orbiting satellites for testing, integration and operations for the Product System Development and Implementation (PSDI) projects at NOAA's National Environmental Satellite, Data, and Information Service (NESDIS). This presentation discusses the evolution of the CIRA NPP/AMSU TC algorithms internally at CIRA and its migration and integration into the NOAA Data Exploitation (NDE) development and testing frameworks. The discussion will focus on 1) the development cycle of internal NPP/AMSU TC algorithms components by scientists and software engineers, 2) the exchange of these components into the NPP/AMSU TC software systems using the subversion version control system and other exchange methods, 3) testing, debugging and integration of the NPP/AMSU TC systems both at CIRA/NESDIS and 4) the update cycle of new releases through continuous integration. Lastly, a discussion of the methods that were effective and those that need revision will be detailed for the next iteration of the NPP/AMSU TC system.

  1. Equivalent models of wind farms by using aggregated wind turbines and equivalent winds

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, L.M.; Garcia, C.A.; Saenz, J.R. [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n. 11202 Algeciras, Cadiz (Spain); Jurado, F. [Department of Electrical Engineering, EPS Linares, University of Jaen, C/ Alfonso X, n 28. 23700 Linares, Jaen (Spain)

    2009-03-15

    As a result of the increasing wind farms penetration on power systems, the wind farms begin to influence power system, and therefore the modeling of wind farms has become an interesting research topic. In this paper, new equivalent models of wind farms equipped with wind turbines based on squirrel-cage induction generators and doubly-fed induction generators are proposed to represent the collective behavior on large power systems simulations, instead of using a complete model of wind farms where all the wind turbines are modeled. The models proposed here are based on aggregating wind turbines into an equivalent wind turbine which receives an equivalent wind of the ones incident on the aggregated wind turbines. The equivalent wind turbine presents re-scaled power capacity and the same complete model as the individual wind turbines, which supposes the main feature of the present equivalent models. Two equivalent winds are evaluated in this work: (1) the average wind from the ones incident on the aggregated wind turbines with similar winds, and (2) an equivalent incoming wind derived from the power curve and the wind incident on each wind turbine. The effectiveness of the equivalent models to represent the collective response of the wind farm at the point of common coupling to grid is demonstrated by comparison with the wind farm response obtained from the detailed model during power system dynamic simulations, such as wind fluctuations and a grid disturbance. The present models can be used for grid integration studies of large power system with an important reduction of the model order and the computation time. (author)

  2. Equivalent models of wind farms by using aggregated wind turbines and equivalent winds

    International Nuclear Information System (INIS)

    As a result of the increasing wind farms penetration on power systems, the wind farms begin to influence power system, and therefore the modeling of wind farms has become an interesting research topic. In this paper, new equivalent models of wind farms equipped with wind turbines based on squirrel-cage induction generators and doubly-fed induction generators are proposed to represent the collective behavior on large power systems simulations, instead of using a complete model of wind farms where all the wind turbines are modeled. The models proposed here are based on aggregating wind turbines into an equivalent wind turbine which receives an equivalent wind of the ones incident on the aggregated wind turbines. The equivalent wind turbine presents re-scaled power capacity and the same complete model as the individual wind turbines, which supposes the main feature of the present equivalent models. Two equivalent winds are evaluated in this work: (1) the average wind from the ones incident on the aggregated wind turbines with similar winds, and (2) an equivalent incoming wind derived from the power curve and the wind incident on each wind turbine. The effectiveness of the equivalent models to represent the collective response of the wind farm at the point of common coupling to grid is demonstrated by comparison with the wind farm response obtained from the detailed model during power system dynamic simulations, such as wind fluctuations and a grid disturbance. The present models can be used for grid integration studies of large power system with an important reduction of the model order and the computation time

  3. Wind speed forecasting for wind energy applications

    Science.gov (United States)

    Liu, Hong

    With more wind energy being integrated into our grid systems, forecasting wind energy has become a necessity for all market participants. Recognizing the market demands, a physical approach to site-specific hub-height wind speed forecasting system has been developed. This system is driven by the outputs from the Canadian Global Environmental Multiscale (GEM) model. A simple interpolation approach benchmarks the forecasting accuracy inherited from GEM. Local, site specific winds are affected on a local scale by a variety of factors including representation of the land surface and local boundary-layer process over heterogeneous terrain which have been a continuing challenge in NWP models like GEM with typical horizontal resolution of order 15-km. In order to resolve these small scale effects, a wind energy industry standard model, WAsP, is coupled with GEM to improve the forecast. Coupling the WAsP model with GEM improves the overall forecasts, but remains unsatisfactory for forecasting winds with abrupt surface condition changes. Subsequently in this study, a new coupler that uses a 2-D RANS model of boundary-layer flow over surface condition changes with improved physics has been developed to further improve the forecasts when winds coming from a water surface to land experience abrupt changes in surface conditions. It has been demonstrated that using vertically averaged wind speeds to represent geostrophic winds for input into the micro-scale models could reduce forecast errors. The hub-height wind speed forecasts could be further improved using a linear MOS approach. The forecasting system has been evaluated, using a wind energy standard evaluation matrix, against data from an 80-m mast located near the north shore of Lake Erie. Coupling with GEM-LAM and a power conversion model using a theoretical power curve have also been investigated. For hub-height wind speeds GEM appears to perform better with a 15-Ian grid than the high resolution GEM-2.5Ian version at the

  4. Effects of massive wind power integration on short-term water resource management in central Chile - a grid-wide study

    Science.gov (United States)

    Haas, J.; Olivares, M. A.; Palma, R.

    2013-12-01

    In central Chile, water from reservoirs and streams is mainly used for irrigation and power generation. Hydropower reservoirs operation is particularly challenging because: i) decisions at each plant impact the entire power system, and ii) the existence of large storage capacity implies inter-temporal ties. An Independent System Operator (ISO) decides the grid-wide optimal allocation of water for power generation, under irrigation-related constraints. To account for the long-term opportunity cost of water, a future cost function is determined and used in the short term planning. As population growth and green policies demand increasing levels of renewable energy in power systems, deployment of wind farms and solar plants is rising quickly. However, their power output is highly fluctuating on short time scales, affecting the operation of power plants, particularly those fast responding units as hydropower reservoirs. This study addresses these indirect consequences of massive introduction of green energy sources on reservoir operations. Short-term reservoir operation, under different wind penetration scenarios, is simulated using a replica of Chile's ISO's scheduling optimization tools. Furthermore, an ongoing study is exploring the potential to augment the capacity the existing hydro-power plants to better cope with the balancing needs due to a higher wind power share in the system. As reservoir releases determine to a great extent flows at downstream locations, hourly time series of turbined flows for 24-hour periods were computed for selected combinations between new wind farms and increased capacity of existing hydropower plants. These time series are compiled into subdaily hydrologic alteration (SDHA) indexes (Zimmerman et al, 2010). The resulting sample of indexes is then analyzed using duration curves. Results show a clear increase in the SDHA for every reservoir of the system as more fluctuating renewables are integrated into the system. High

  5. Recent Canyon Heads at the Bosphorus Outlet

    Science.gov (United States)

    Lericolais, G.; Le Drezen, E.; Nouze, H.; Gillet, H.; Ergun, M.; Cific, G.; Avci, M.; Dondurur, D.; Okay, S.

    2002-12-01

    The Black and Marmara Seas have witnessed increased scientific interest in last decade due to improved cooperation between the riparian countries and western scientific institutions but also due to the controversy existing about the origin of the reconnection of the Black Sea and Mediterranean seas after the last Glacial Maximum and its ensuing sea level rise. The Black Sea is linked to the global ocean only through the Bosphorus-Dardanelles system of straits. The Bosphorus is narrow (0.76 to 3.6 km wide) and shallow (32 m) at the sill, restricting the two-way water exchange between the brackish Black Sea and the very saline Mediterranean Sea. The Bosphorus sill was responsible for the behaviour of the Black Sea during the global glaciations and deglaciations, during which the Black Sea level followed the global sea level changes as long as they were higher than the sill. When global sea level was lower than the Bosphorus sill the variations of the Black Sea level reflected specific regional climate conditions without being coupled to the ocean changes. Recent studies suggest that a rapid flooding event may have occurred in the Black Sea during the Holocene. In 1998, a French-Romanian survey collected 4500 km of high-resolution seismic profiles, multibeam bathymetry, and sediment cores on the northern margin of the Black Sea where the shelf is sufficiently wide to preserve ancient shorelines in the vicinity of the shelf edge. If rapid flooding occurred through the Bosphorus Strait to drown these shorelines, it should have created a cataract. In August 2002, the French research vessel "Le Suroit" equipped with a EM 300 multibeam echosounder and a TritonElics Chirp Sonar mapped the Bosphorus outlet at the shelf edge. The results show a large retrogressive canyon deeply incised into the shelf which can be followed landward towards the Bosphorus outlet. Coring on the shelf and in the canyon revealed mega-ripples of shell debris of recent origin.

  6. 风力发电经分频输电接入系统的实验%Experiment on Wind Power Grid Integration via Fractional Frequency Transmission System

    Institute of Scientific and Technical Information of China (English)

    宁联辉; 王锡凡; 滕予非; 刘奎; 宋卓彦; 朱卫平

    2011-01-01

    Fractional frequency transmission system(FFTS) provides a novel approach for the remote wind farm integrated into grid. This approach could overcome the great challenges caused by the randomicity and the intermittence of the wind power. The key equipment of FFTS was cycloconverter. First, an experimental FFTS was proposed. And the power circuit and the control circuit of the 12-pulse cycloconverter were designed. In this experimental system, a synchronizing generator was used to simulate the permanent magnet synchronous generator (PMSG) in wind farm. Furthermore, the operation mode of cycloconverter was discussed. Finally, the open-loop active power regulations method was also introduced. Experiment results show that this system can transmit 20 kW electric power into grid, and verify the realizability of the system which used to integrate wind power into grid via FFTS.%风力发电具有随机性、间歇性,而且风电场一般处于偏远地区,风电经分频输电接入电网为风电的远距离输送提供了一个解决方案。该文设计了12脉波交交变频器的主电路和控制电路,并以其作为风电接入装置,用常规同步发电机模拟永磁直驱同步发电机,在动模实验室模拟了变速变频风力发电,向系统成功输送20kW有功,证实了以分频输电为背景的变速变频风力发电的可实现性,并在此基础上初步讨论了交交变频器的运行方式,实现了风电场的有功开环调节。

  7. Piezoelectric wind turbine

    Science.gov (United States)

    Kishore, Ravi Anant; Priya, Shashank

    2013-03-01

    In past few years, there has been significant focus towards developing small scale renewable energy based power sources for powering wireless sensor nodes in remote locations such as highways and bridges to conduct continuous health monitoring. These prior efforts have led to the development of micro-scale solar modules, hydrogen fuel cells and various vibration based energy harvesters. However, the cost effectiveness, reliability, and practicality of these solutions remain a concern. Harvesting the wind energy using micro-to-small scale wind turbines can be an excellent solution in variety of outdoor scenarios provided they can operate at few miles per hour of wind speed. The conventional electromagnetic generator used in the wind mills always has some cogging torque which restricts their operation above certain cut-in wind speed. This study aims to develop a novel piezoelectric wind turbine that utilizes bimorph actuators for electro-mechanical energy conversion. This device utilizes a Savonius rotor that is connected to a disk having magnets at the periphery. The piezoelectric actuators arranged circumferentially around the disk also have magnets at the tip which interacts with the magnetic field of the rotating disk and produces cyclical deflection. The wind tunnel experiments were conducted between 2-12 mph of wind speeds to characterize and optimize the power output of the wind turbine. Further, testing was conducted in the open environment to quantify the response to random wind gusts. An attempt was made towards integration of the piezoelectric wind turbine with the wireless sensor node.

  8. Marine litter on the floor of deep submarine canyons of the Northwestern Mediterranean Sea: The role of hydrodynamic processes

    Science.gov (United States)

    Tubau, Xavier; Canals, Miquel; Lastras, Galderic; Rayo, Xavier; Rivera, Jesus; Amblas, David

    2015-05-01

    Marine litter represents a widespread type of pollution in the World's Oceans. This study is based on direct observation of the seafloor by means of Remotely Operated Vehicle (ROV) dives and reports litter abundance, type and distribution in three large submarine canyons of the NW Mediterranean Sea, namely Cap de Creus, La Fonera and Blanes canyons. Our ultimate objective is establishing the links between active hydrodynamic processes and litter distribution, thus going beyond previous, essentially descriptive studies. Litter was monitored using the Liropus 2000 ROV. Litter items were identified in 24 of the 26 dives carried out in the study area, at depths ranging from 140 to 1731 m. Relative abundance of litter objects by type, size and apparent weight, and distribution of litter in relation to depth and canyon environments (i.e. floor and flanks) were analysed. Plastics are the dominant litter component (72%), followed by lost fishing gear, disregarding their composition (17%), and metal objects (8%). Most of the observed litter seems to be land-sourced. It reaches the ocean through wind transport, river discharge and after direct dumping along the coastline. While coastal towns and industrial areas represent a permanent source of litter, tourism and associated activities relevantly increase litter production during summer months ready to be transported to the deep sea by extreme events. After being lost, fishing gear such as nets and long-lines has the potential of being harmful for marine life (e.g. by ghost fishing), at least for some time, but also provides shelter and a substrate on which some species like cold-water corals are capable to settle and grow. La Fonera and Cap de Creus canyons show the highest mean concentrations of litter ever seen on the deep-sea floor, with 15,057 and 8090 items km-2, respectively, and for a single dive litter observed reached 167,540 items km-2. While most of the largest concentrations were found on the canyon floors at

  9. Current development of the ENTSO-E NC RfG in the light of European wind integration

    Energy Technology Data Exchange (ETDEWEB)

    Duddy, Joe [RES Ltd., Belfast (United Kingdom); Martin, Frank; Skrypalle, Inga [Siemens Wind Power A/S, Brande (Denmark); Hulle, Frans van [EWEA, Brussels (Belgium); Wachtel, Stephan [GE Energy, Hamburg (Germany)

    2012-07-01

    Over the entire development of the NC RfG EWEA has been in dialogue with ENTSO-E. EWEA is concerned that network operators tend to increase the compulsory minimum technical connection requirements for wind power plants without clearly explaining the needs (system planning and analyses results, cost-benefit-analyses, etc.) in a transparent way. Grid codes in Europe should at first consider ancillary services market options instead of compulsory requirements to be fulfilled without specific remuneration. The compulsory technical requirements for all generators must therefore focus on the essential aspects of technical performances, leaving an opening for ancillary services within adequately implemented markets. (orig.)

  10. A New Method for Start-up of Isolated Boost Converters Using Magnetic- and Winding-Integration

    DEFF Research Database (Denmark)

    Lindberg-Poulsen, Kristian; Ouyang, Ziwei; Sen, Gökhan;

    2012-01-01

    . The traditional added flyback winding coupled to the boost inductor is thus eliminated from the circuit, bringing substantial cost savings, increased efficiency and simplified design. Each subinterval of the converter operation is described through electrical and magnetic circuit diagrams, and the concept...... is extended to other isolated boost family topologies. The principle of operation is demonstrated with a 800W isolated boost prototype, and a 1600W primary parallel series secondary isolated boost converter. Efficiency measurements of both prototypes are presented, including measurements during both start...

  11. Habitat Mapping Cruise - Hudson Canyon (HB0904, EK60)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Objectives are to: 1) perform multibeam mapping of transitional and deepwater habitats in Hudson Canyon (off New Jersey) with the National Institute of Undersea...

  12. BackscatterC [7125]--Monterey Canyon and Vicinity, California

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This part of DS 781 presents data for the acoustic-backscatter map of Monterey Canyon and Vicinity map area, California. Backscatter data are provided as separate...

  13. BackscatterB [EM300]--Monterey Canyon and Vicinity, California

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This part of DS 781 presents data for the acoustic-backscatter map of Monterey Canyon and Vicinity map area, California. Backscatter data are provided as separate...

  14. Ecological-geochemical assessment of soil of the Dniester canyon.

    Directory of Open Access Journals (Sweden)

    Zorin D.O.

    2008-05-01

    Full Text Available An method of calculation of background and anomalous heavy metals, petroleum products and pesticides in soil of the Dniester canyon area for the environmental assessment of the future national park.

  15. Folds--Monterey Canyon and Vicinity Map Area, California

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This part of DS 781 presents data for the folds for the geologic and geomorphic map of Monterey Canyon and Vicinity, California. The vector data file is included in...

  16. Faults--Monterey Canyon and Vicinity Map Area, California

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This part of DS 781 presents data for the faults for the geologic and geomorphic map of Monterey Canyon and Vicinity, California. The vector data file is included...

  17. Paleoshorelines--Monterey Canyon and Vicinity Map Area, California

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This part of DS 781 presents data for the paleoshorelines for the geologic and geomorphic map of Monterey Canyon and Vicinity, California. The vector data file is...

  18. The Trail Inventory of Leslie Canyon NWR [Cycle 2

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The purpose of this report is to create a baseline inventory of all non-motorized trails on Leslie Canyon National Wildlife Refuge. Trails in this inventory are...

  19. Better integration of wind power. Analysis of Danish legislation on tariffs, taxes and other significant conditions. Summary report and 3 appendix reports.; Denmark; Bedre integration af vind. Analyse af elpatronloven, treledstariffen for mindre kraftvarmeanlaeg, afgifter og andre vaesentlige rammebetingelser. Sammenfatning samt 3 bilagsrapporter

    Energy Technology Data Exchange (ETDEWEB)

    Togeby, M.; Werling, J.; Hethey, J. (and others)

    2009-06-15

    For the Danish Energy Agency and the Danish Ministry of Taxation, Ea Energianalyse and Risoe DTU have analysed how wind power can be better integrated into Danish the energy system so that economic and environmental impact of wind power improves. As a particular task, it is assessed whether the pilot scheme of reduced tariffs for electricity for heat and the payment for electricity for small cogeneration plants are appropriate. A number of framework conditions and technical solutions are evaluated and prioritized as part of the general assessment of options for better integration of wind power in the Danish power system. Besides the synthesis report, the publication contains three sub reports, which provide an analysis of the issues on integration of wind power, an analysis of the various options, and an analysis of the socioeconomic consequences by changing the taxes and tariffs. (ln)

  20. H CANYON PROCESSING IN CORRELATION WITH FH ANALYTICAL LABS

    Energy Technology Data Exchange (ETDEWEB)

    Weinheimer, E.

    2012-08-06

    Management of radioactive chemical waste can be a complicated business. H Canyon and F/H Analytical Labs are two facilities present at the Savannah River Site in Aiken, SC that are at the forefront. In fact H Canyon is the only large-scale radiochemical processing facility in the United States and this processing is only enhanced by the aid given from F/H Analytical Labs. As H Canyon processes incoming materials, F/H Labs provide support through a variety of chemical analyses. Necessary checks of the chemical makeup, processing, and accountability of the samples taken from H Canyon process tanks are performed at the labs along with further checks on waste leaving the canyon after processing. Used nuclear material taken in by the canyon is actually not waste. Only a small portion of the radioactive material itself is actually consumed in nuclear reactors. As a result various radioactive elements such as Uranium, Plutonium and Neptunium are commonly found in waste and may be useful to recover. Specific processing is needed to allow for separation of these products from the waste. This is H Canyon's specialty. Furthermore, H Canyon has the capacity to initiate the process for weapons-grade nuclear material to be converted into nuclear fuel. This is one of the main campaigns being set up for the fall of 2012. Once usable material is separated and purified of impurities such as fission products, it can be converted to an oxide and ultimately turned into commercial fuel. The processing of weapons-grade material for commercial fuel is important in the necessary disposition of plutonium. Another processing campaign to start in the fall in H Canyon involves the reprocessing of used nuclear fuel for disposal in improved containment units. The importance of this campaign involves the proper disposal of nuclear waste in order to ensure the safety and well-being of future generations and the environment. As processing proceeds in the fall, H Canyon will have a substantial

  1. Low-Carbon Economic Dispatching for Power Grid Integrated with Carbon Capture Power Plants and Wind Power System

    Directory of Open Access Journals (Sweden)

    Sheng Siqing

    2015-01-01

    Full Text Available Carbon emission characteristics of all kinds of power units are analyzed against the background of the low carbon economy. This paper introduces carbon trading in the dispatching model, gives full consideration to the benefit or cost of carbon emission and introduces carbon emission in the dispatching model as a decision variable so as to achieve the unity of the economy and the environmental protection of the dispatching model. A low carbon economic dispatching model is established based on multiple objectives, such as the lowest thermal power generation cost, the lowest carbon trading cost and the lowest carbon capture power plant operation cost. Load equalization, output constraint of power unit, ramping constraint, spinning reserve constraint and carbon capture efficiency constraint should be taken into account in terms of constraint conditions. The model is solved by the particle swarm optimization based on dynamic exchange and density distance. The fact that the introduction of carbon trading can effectively reduce the level of carbon emission and increase the acceptance level of wind power is highlighted through the comparison of the results of three models’ computational examples. With the carbon trading mechanism, carbon capture power plants with new technologies are able to give full play to the advantage of reducing carbon emission and wind curtailment so as to promote the development of the energy conservation and emission reduction technology and reduce the total cost of the dispatching system.

  2. Damming Grand Canyon: The 1923 USGS Colorado River Expedition

    OpenAIRE

    Boyer, Diane E.; Webb, Robert H.

    2007-01-01

    In 1923, America paid close attention, via special radio broadcasts, newspaper headlines, and cover stories in popular magazines, as a government party descended the Colorado to survey Grand Canyon. Fifty years after John Wesley Powell's journey, the canyon still had an aura of mystery and extreme danger. At one point, the party was thought lost in a flood. Something important besides adventure was going on. Led by Claude Birdseye and including colorful characters such as early river-runner E...

  3. Safety Evaluation for Packaging (onsite) T Plant Canyon Items

    Energy Technology Data Exchange (ETDEWEB)

    OBRIEN, J.H.

    2000-07-14

    This safety evaluation for packaging (SEP) evaluates and documents the ability to safely ship mostly unique inventories of miscellaneous T Plant canyon waste items (T-P Items) encountered during the canyon deck clean off campaign. In addition, this SEP addresses contaminated items and material that may be shipped in a strong tight package (STP). The shipments meet the criteria for onsite shipments as specified by Fluor Hanford in HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments.

  4. Safety Evaluation for Packaging (onsite) T Plant Canyon Items

    International Nuclear Information System (INIS)

    This safety evaluation for packaging (SEP) evaluates and documents the ability to safely ship mostly unique inventories of miscellaneous T Plant canyon waste items (T-P Items) encountered during the canyon deck clean off campaign. In addition, this SEP addresses contaminated items and material that may be shipped in a strong tight package (STP). The shipments meet the criteria for onsite shipments as specified by Fluor Hanford in HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments

  5. Wind power in power systems

    CERN Document Server

    Ackermann, Thomas

    2012-01-01

    The second edition of the highly acclaimed Wind Power in Power Systems has been thoroughly revised and expanded to reflect the latest challenges associated with increasing wind power penetration levels. Since its first release, practical experiences with high wind power penetration levels have significantly increased. This book presents an overview of the lessons learned in integrating wind power into power systems and provides an outlook of the relevant issues and solutions to allow even higher wind power penetration levels. This includes the development of standard wind turbine sim

  6. Danish Wind Power

    DEFF Research Database (Denmark)

    Lund, Henrik; Hvelplund, Frede; Østergaard, Poul Alberg;

    In a normal wind year, Danish wind turbines generate the equivalent of approx. 20 percent of the Danish electricity demand. This paper argues that only approx. 1 percent of the wind power production is exported. The rest is used to meet domestic Danish electricity demands. The cost of wind power...... is paid solely by the electricity consumers and the net influence on consumer prices was as low as 1-3 percent on average in the period 2004-2008. In 2008, the net influence even decreased the average consumer price, although only slightly. In Denmark, 20 percent wind power is integrated by using both......, a study made by the Danish think tank CEPOS claimed the opposite, i.e. that most of the Danish wind power has been exported in recent years. However, this claim is based on an incorrect interpretation of statistics and a lack of understanding of how the international electricity markets operate...

  7. Operation and Power Flow Control of Multi-Terminal DC Networks for Grid Integration of Offshore Wind Farms Using Genetic Algorithms

    Directory of Open Access Journals (Sweden)

    Rodrigo Teixeira Pinto

    2012-12-01

    Full Text Available For achieving the European renewable electricity targets, a significant contribution is foreseen to come from offshore wind energy. Considering the large scale of the future planned offshore wind farms and the increasing distances to shore, grid integration through a transnational DC network is desirable for several reasons. This article investigates a nine-node DC grid connecting three northern European countries — namely UK, The Netherlands and Germany. The power-flow control inside the multi-terminal DC grid based on voltage-source converters is achieved through a novel method, called distributed voltage control (DVC. In this method, an optimal power flow (OPF is solved in order to minimize the transmission losses in the network. The main contribution of the paper is the utilization of a genetic algorithm (GA to solve the OPF problem while maintaining an N-1 security constraint. After describing main DC network component models, several case studies illustrate the dynamic behavior of the proposed control method.

  8. Integration

    DEFF Research Database (Denmark)

    Emerek, Ruth

    2004-01-01

    Bidraget diskuterer de forskellige intergrationsopfattelse i Danmark - og hvad der kan forstås ved vellykket integration......Bidraget diskuterer de forskellige intergrationsopfattelse i Danmark - og hvad der kan forstås ved vellykket integration...

  9. 2008 High-Flow Experiment at Glen Canyon Dam Benefits Colorado River Resources in Grand Canyon National Park

    Science.gov (United States)

    Melis, Theodore S.; Topping, David J.; Grams, Paul E.; Rubin, David M.; Wright, Scott A.; Draut, Amy E.; Hazel, Joseph E., Jr.; Ralston, Barbara E.; Kennedy, Theodore A.; Rosi-Marshall, Emma; Korman, Josh; Hilwig, Kara D.; Schmit, Lara M.

    2010-01-01

    On March 5, 2008, the Department of the Interior began a 60-hour high-flow experiment at Glen Canyon Dam, Arizona, to determine if water releases designed to mimic natural seasonal flooding could be used to improve downstream resources in Glen Canyon National Recreation Area and Grand Canyon National Park. U.S. Geological Survey (USGS) scientists and their cooperators undertook a wide range of physical and biological resource monitoring and research activities before, during, and after the release. Scientists sought to determine whether or not high flows could be used to rebuild Grand Canyon sandbars, create nearshore habitat for the endangered humpback chub, and benefit other resources such as archaeological sites, rainbow trout, aquatic food availability, and riverside vegetation. This fact sheet summarizes research completed by January 2010.

  10. Integrated control of wind farms, FACTS devices and the power network using neural networks and adaptive critic designs

    Science.gov (United States)

    Qiao, Wei

    Worldwide concern about the environmental problems and a possible energy crisis has led to increasing interest in clean and renewable energy generation. Among various renewable energy sources, wind power is the most rapidly growing one. Therefore, how to provide efficient, reliable, and high-performance wind power generation and distribution has become an important and practical issue in the power industry. In addition, because of the new constraints placed by the environmental and economical factors, the trend of power system planning and operation is toward maximum utilization of the existing infrastructure with tight system operating and stability margins. This trend, together with the increased penetration of renewable energy sources, will bring new challenges to power system operation, control, stability and reliability which require innovative solutions. Flexible ac transmission system (FACTS) devices, through their fast, flexible, and effective control capability, provide one possible solution to these challenges. To fully utilize the capability of individual power system components, e.g., wind turbine generators (WTGs) and FACTS devices, their control systems must be suitably designed with high reliability. Moreover, in order to optimize local as well as system-wide performance and stability of the power system, real-time local and wide-area coordinated control is becoming an important issue. Power systems containing conventional synchronous generators, WTGs, and FACTS devices are large-scale, nonlinear, nonstationary, stochastic and complex systems distributed over large geographic areas. Traditional mathematical tools and system control techniques have limitations to control such complex systems to achieve an optimal performance. Intelligent and bio-inspired techniques, such as swarm intelligence, neural networks, and adaptive critic designs, are emerging as promising alternative technologies for power system control and performance optimization. This

  11. International Experience of Ordered Integration Management on Wind Power and Its Enlightenment to China%国外风电有序并网管理经验对我国的启示

    Institute of Scientific and Technical Information of China (English)

    李晨; 韩锦瑞; 周黎莎; 曾鸣

    2012-01-01

    针对当前我国风电无序并网存在的问题,提出了风电有序并网的概念和内涵,从组织、运行、协调、激励、保障五个方面分析了国外典型国家风电并网管理先进经验,探讨了国外经验对我国风电有序并网管理机制建设的启示,以提升我国风电大规模并网管理水平、促进我国风电有序开发利用.%Aiming at the existing problems of disordered integration of wind power in China, the concept and meaning of ordered integration is put forward. From the aspects of organization, operation, coordination, motivation and guaran tee mechanism, the advanced experience of wind power integration management in typical countries are analyzed. The en lightenment of international experience to construction of ordered integration management mechanism is investigated to raise the level of wind power integration management and promote the ordered exploitation and utilization of wind power.

  12. Web based hybrid volumetric visualisation of urban GIS data. Integration of 4D Temperature and Wind Fields with LoD-2 CityGML models

    Science.gov (United States)

    Congote, J.; Moreno, A.; Kabongo, L.; Pérez, J.-L.; San-José, R.; Ruiz, O.

    2012-10-01

    City models visualisation, buildings, structures and volumetric information, is an important task in Computer Graphics and Urban Planning. The different formats and data sources involved in the visualisation make the development of applications a big challenge. We present a homogeneous web visualisation framework using X3DOM and MEDX3DOM for the visualisation of these urban objects. We present an integration of different declarative data sources, enabling the utilization of advanced visualisation algorithms to render the models. It has been tested with a city model composed of buildings from the Madrid University Campus, some volumetric datasets coming from Air Quality Models and 2D layers wind datasets. Results show that the visualisation of all the urban models can be performed in real time on the Web. An HTML5 web interface is presented to the users, enabling real time modifications of visualisation parameters.

  13. Optimal Power Management of a DISCO with Integrations of Reliability Considerations and Wind Farm Based on Benders Decomposition

    Directory of Open Access Journals (Sweden)

    M. Baghdadi

    2011-01-01

    Full Text Available This paper presents a comprehensive framework model of a distribution company with security and reliability considerations. A probabilistic wind farm, which is a renewable energy resource, is modeled in this work. The requirement energy of distribution company can be either provided by distribution company's own distributed generations or purchased from power market. Two reliability indices as well as DC load flow equations are also considered in order to satisfy reliability and security constraints, respectively. Since allocating proper spinning reserve improves reliability level, the amount of spinning reserve will be calculated iteratively. In this work, all equations are expressed in a linear fashion in which unit commitment formulation depends on binary variables associated with only on/off of units. The benders decomposition method is used to solve security-based unit commitment.

  14. Effects of differential wall heating in street canyons on dispersion and ventilation characteristics of a passive scalar

    Science.gov (United States)

    Cai, Xiaoming

    2012-05-01

    This paper presents the first large-eddy simulation (LES) study of transfer and dispersion of a scalar released from a rough urban facet, either the street surface, the upstream-wall, or the downstream-wall, under the thermo-dynamical conditions of either the upstream-wall or the downstream-wall, plus the roof, heated by solar radiation. The boundary condition of a constant value is adopted for the scalars on the rough urban facets and a wall function is proposed for the scalars. The LES results demonstrate that dispersion inside the street canyon possesses distinctive characteristics for two conditions: the assisting condition in which the thermal-driven flow has the same direction as that of the wind-driven vortex and the opposing condition in which the thermal-driven flow has the opposite direction as that of the wind-driven vortex. For the street-released scalar under the opposing condition, the concentration fluctuations relative to the mean concentration can reach 50% and in general they are much larger than those for the assisting cases which are in the range of 25-30%. The exchange velocity of a scalar between the street canyon air and the urban boundary layer (UBL), wCB(c), is one order of magnitude larger than the exchange velocity between a facet and the urban boundary layer, UBL, w0B(c), indicating quantitatively that the resistance to the transfer of a facet-released scalar is dominated by the near-facet processes. As the temperature difference between the wall and the UBL, ΔT, increases, the total resistance to street canyon ventilation becomes more dominated by the near-facet resistance. The assisting conditions are favourable to ventilating the scalars from both walls, whereas the opposing conditions are only favourable to the ventilation of the downstream-wall released scalar. In the range of ΔT tested in this study, the exchange velocity, wCB(c), linearly increases with ΔT and can be well parameterised. For the assisting cases, the advective

  15. 风/柴联合电力系统运行策略评估%Operating Strategy Evaluation of Integrated Wind/Diesel Systems

    Institute of Scientific and Technical Information of China (English)

    栗文义; 张保会; 巴根

    2006-01-01

    Many remote communities around the world cannot be physically or economically connected to an electric power grid. The electricity demand in these areas is conventionally supplied by small isolated diesel plants. Rapidly escalating fossil fuel costs together with difficulties in fuel delivery and equipment maintenance results in unacceptably high generating costs at these diesel plants. Considerable fuel savings can be achieved by integrating renewable sources such as wind and/or solar energy with existing diesel plants. Due to the fluctuating nature of the site resources in the form of wind and/or sunlight, there are several operating problems on reliability and economics.This paper presents a sequential simulation technique to evaluate the different operating strategies for integrated wind/diesel power systems. The advantages and disadvantages of these strategies are analyzed with regard to reliability, diesel fuel saving, back-up diesel average start-stop cycles, average running time, etc.%世界上许多偏远地方的社区远离电网,不具备由电网供电的条件.这些地区的电力负荷传统上由小型孤立柴油电站供电.快速上升的矿石燃料成本以及运输和设备维护问题导致这些柴油电站发电成本很高.通过把风或太阳能这样的可再生能源与现有的柴油电站并联运行,可节省大量的燃料.文中提出一个评估风/柴联合电力系统不同运行策略的顺序仿真方法,运用该方法分析了这些运行策略在可靠性、柴油燃料节省、备用柴油发电机平均起停周期和平均运行时间等方面的优缺点.

  16. 2010 weather and aeolian sand-transport data from the Colorado River corridor, Grand Canyon, Arizona

    Science.gov (United States)

    Dealy, Timothy P.; East, Amy E.; Fairley, Helen C.

    2014-01-01

    Measurements of weather parameters and aeolian sand transport were made in 2010 near selected archeological sites in the Colorado River corridor through Grand Canyon, Arizona. Data collected in 2010 indicate event- and seasonal-scale variations in rainfall, wind, temperature, humidity, and barometric pressure. Differences in weather patterns between 2009 and 2010 included a slightly later spring windy season, greater spring precipitation and annual rainfall totals, and a later onset and length of the reduced diurnal barometric-pressure fluctuations commonly associated with summer monsoon conditions. The increase in spring precipitation was consistent with the 2010 spring El Niño conditions compared to the 2009 spring La Niña conditions, whereas the subsequent transition to an El Niño-Southern Oscillation neutral phase appeared to delay the reduction in diurnal barometric fluctuations.

  17. Wind Energy Conversion Systems Technology and Trends

    CERN Document Server

    2012-01-01

    Wind Energy Conversion System covers the technological progress of wind energy conversion systems, along with potential future trends. It includes recently developed wind energy conversion systems such as multi-converter operation of variable-speed wind generators, lightning protection schemes, voltage flicker mitigation and prediction schemes for advanced control of wind generators. Modeling and control strategies of variable speed wind generators are discussed, together with the frequency converter topologies suitable for grid integration. Wind Energy Conversion System also describes offshore farm technologies including multi-terminal topology and space-based wind observation schemes, as well as both AC and DC based wind farm topologies. The stability and reliability of wind farms are discussed, and grid integration issues are examined in the context of the most recent industry guidelines. Wind power smoothing, one of the big challenges for transmission system operators, is a particular focus. Fault ride th...

  18. Probabilistic modeling of wind energy sources integrated in a conventional power system; Modelagem probabilistica de fontes eolicas de energia integradas em sistema de potencia convencional

    Energy Technology Data Exchange (ETDEWEB)

    Dalence, G.W.H.

    1990-06-15

    This work describes a model capable of including non-conventional energy sources into a stochastic energy production model for conventional power sources. A wind energy system is initially considered as statistically independent of the hourly demand. The correlation between two wind systems is then considered by means of a joint wind speed distribution. The joint wind system is thereafter submitted to the stochastic energy production model considering independence between demand and wind speed. Finally the correlation wind systems and the hourly demand is studied. (author). 29 figs, 31 tabs

  19. Geology of the Hamm Canyon quadrangle, Colorado

    Science.gov (United States)

    Cater, Fred W.

    1953-01-01

    The Hamm Canyon quadrangle is on eof eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by high-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

  20. Davis Canyon noise analysis: Revision 2

    International Nuclear Information System (INIS)

    A study was performed as part of the Civilian Radioactive Waste Management Program to quantify the level and effect of noise from the various major phases of development of the proposed potentially acceptable nuclear waste repository site at Davis Canyon, Utah. This report contains the results of a predictive noise level study for the site characterization, repository construction, and repository operational phases. Included herein are graphic representations of energy averaged sound levels, and of audibility levels representing impact zones expected during each phase. Sound levels from onsite and offsite activity including traffic on highways and railroad routes are presented in isopleth maps. A description of the Environmental Noise Prediction Model used for the study, the study basis and methodologies, and actual modeling data are provided. Noise and vibration levels from blasting are also predicted and evaluated. Protective noise criteria containing a margin of safety are used in relation to residences, schools, churches, noise-sensitive recreation areas, and noise-sensitive biological resources. Protective ground motion criteria for ruins and delicate rock formation in Canyonlands National Park and for human annoyance are used in the evaluation of blasting. The evaluations provide the basis for assessing the noise impacts from the related activities at the proposed repository. 45 refs., 21 figs., 15 tabs

  1. Nordic wind power conference 2007. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Cutululis, N.; Soerensen, P. (eds.)

    2007-11-15

    This fourth Nordic Wind Power Conference was focused on power system integration and electrical systems of wind turbines and wind farms. NWPC presents the newest research results related to technical electrical aspects of wind power, spanning from power system integration to electrical design and control of wind turbines. The first NWPC was held in Trondheim (2000), Norway, the second in Gothenburg (2004), Sweden, and the third in Espoo (2006), Finland. Invited speakers, oral presentation of papers and poster sessions ensured this to be a valuable event for professionals and high-level students wanting to strengthen their knowledge on wind power integration and electrical systems. (au)

  2. Nordic wind power conference 2007. Proceedings

    International Nuclear Information System (INIS)

    This fourth Nordic Wind Power Conference was focused on power system integration and electrical systems of wind turbines and wind farms. NWPC presents the newest research results related to technical electrical aspects of wind power, spanning from power system integration to electrical design and control of wind turbines. The first NWPC was held in Trondheim (2000), Norway, the second in Gothenburg (2004), Sweden, and the third in Espoo (2006), Finland. Invited speakers, oral presentation of papers and poster sessions ensured this to be a valuable event for professionals and high-level students wanting to strengthen their knowledge on wind power integration and electrical systems. (au)

  3. Selection and Performance-Degradation Modeling of LiMO2/Li4Ti5O12 and LiFePO4/C Battery Cells as Suitable Energy Storage Systems for Grid Integration With Wind Power Plants

    DEFF Research Database (Denmark)

    Swierczynski, Maciej Jozef; Stroe, Daniel Ioan; Stan, Ana-Irina;

    2014-01-01

    Advances in the development of energy storage technologies are making them attractive for grid integration together with wind power plants. Thus, the new system, the virtual power plant, is able to emulate the characteristics of today’s conventional power plants. However, at present, energy stora...

  4. Online Supplementary ADP Learning Controller Design and Application to Power System Frequency Control With Large-Scale Wind Energy Integration.

    Science.gov (United States)

    Guo, Wentao; Liu, Feng; Si, Jennie; He, Dawei; Harley, Ronald; Mei, Shengwei

    2016-08-01

    The emergence of smart grids has posed great challenges to traditional power system control given the multitude of new risk factors. This paper proposes an online supplementary learning controller (OSLC) design method to compensate the traditional power system controllers for coping with the dynamic power grid. The proposed OSLC is a supplementary controller based on approximate dynamic programming, which works alongside an existing power system controller. By introducing an action-dependent cost function as the optimization objective, the proposed OSLC is a nonidentifier-based method to provide an online optimal control adaptively as measurement data become available. The online learning of the OSLC enjoys the policy-search efficiency during policy iteration and the data efficiency of the least squares method. For the proposed OSLC, the stability of the controlled system during learning, the monotonic nature of the performance measure of the iterative supplementary controller, and the convergence of the iterative supplementary controller are proved. Furthermore, the efficacy of the proposed OSLC is demonstrated in a challenging power system frequency control problem in the presence of high penetration of wind generation.

  5. Online Supplementary ADP Learning Controller Design and Application to Power System Frequency Control With Large-Scale Wind Energy Integration.

    Science.gov (United States)

    Guo, Wentao; Liu, Feng; Si, Jennie; He, Dawei; Harley, Ronald; Mei, Shengwei

    2016-08-01

    The emergence of smart grids has posed great challenges to traditional power system control given the multitude of new risk factors. This paper proposes an online supplementary learning controller (OSLC) design method to compensate the traditional power system controllers for coping with the dynamic power grid. The proposed OSLC is a supplementary controller based on approximate dynamic programming, which works alongside an existing power system controller. By introducing an action-dependent cost function as the optimization objective, the proposed OSLC is a nonidentifier-based method to provide an online optimal control adaptively as measurement data become available. The online learning of the OSLC enjoys the policy-search efficiency during policy iteration and the data efficiency of the least squares method. For the proposed OSLC, the stability of the controlled system during learning, the monotonic nature of the performance measure of the iterative supplementary controller, and the convergence of the iterative supplementary controller are proved. Furthermore, the efficacy of the proposed OSLC is demonstrated in a challenging power system frequency control problem in the presence of high penetration of wind generation. PMID:26087500

  6. Discovery of two new large submarine canyons in the Bering Sea

    Science.gov (United States)

    Carlson, P.R.; Karl, Herman A.

    1984-01-01

    The Beringian continental margin is incised by some of the world's largest submarine canyons. Two newly discovered canyons, St. Matthew and Middle, are hereby added to the roster of Bering Sea canyons. Although these canyons are smaller and not cut back into the Bering shelf like the five very large canyons, they are nonetheless comparable in size to most of the canyons that have been cut into the U.S. eastern continental margin and much larger than the well-known southern California canyons. Both igneous and sedimentary rocks of Eocene to Pliocene age have been dredged from the walls of St. Matthew and Middle Canyons as well as from the walls of several of the other Beringian margin canyons, thus suggesting a late Tertiary to Quaternary genesis of the canyons. We speculate that the ancestral Yukon and possibly Anadyr Rivers were instrumental in initiating the canyon-cutting processes, but that, due to restrictions imposed by island and subsea bedrock barriers, cutting of the two newly discovered canyons may have begun later and been slower than for the other five canyons. ?? 1984.

  7. China wind power integration status quo and its benefit to energy saving and emission reduction%中国风电并网现状及风电节能减排效益分析

    Institute of Scientific and Technical Information of China (English)

    朱柯丁; 宋艺航; 谭忠富; 张会娟

    2011-01-01

    针对现阶段中国风电发展政策环境进行研究,就其中的不足提出未来改革的方向.介绍中国风电的并网状况,对中国风电并网的瓶颈进行分析.测算中国风电并网后的经济效益,结果表明风电行业收益状况良好,并且风力资源越丰富的地区利润水平越高;而通过扩大各风电资源区的电价差距将有助于促进风电在全国的均衡发展.对风电并网发电现在及未来的节能减排效益进行研究,预测结果表明,随着风电规模的壮大,风电对火电置换的环境效益将日益显著.%Based on the research of wind power development policies, the reformatory direction to overcome the disadvantages of the policies was proposed. The wind power's grid integration status quo was introduced, and the bottle neck of grid integration was analyzed. The study results on the economic benefits of the wind power integration in China's present stage indicate that the wind power industry is in good profit condition. The profit levels are higher in areas with the richer wind resources. Expanding the margin of the power purchase prices in different resource areas is beneficial to the nationwide proportionate development of wind power. At last, the present and future benefits for the energy conservation and emission reduction from the wind power integration were estimated. The forecast result indicates that the environmental benefits of "wind-thermal exchange" will be increased along with the expansion of the using scale of wind power.

  8. Second wind in the offshore wind industry

    International Nuclear Information System (INIS)

    After several keynote addresses, this publication contains contributions and Power Point presentations proposed during this conference on the development of offshore wind energy. The successive sessions addressed the following issues: the offshore mass production of electricity (examples of Denmark and Belgium, laying and protecting offshore cables), the space, economic and environmental planning (the Danish experience, the role of the Coastal area integrated management, importance of the public debate, so on), the logistics of port infrastructures (simulation tools, example of Bremerhaven, issues related to project management), innovation at the core of industrial strategies (high power wind turbines, the 6 MW Alstom turbine, chain value and innovation in offshore wind energy, the Vertiwing innovating project of a floating wind turbine, a bench test in Charleston, foundations, gravity base structures, the British experience, the Danish experience), the economic and organisational conditions for development, the validation and certification of technologies

  9. Spatial Vegetation Data for Canyon De Chelly National Monument Vegetation Mapping Project

    Data.gov (United States)

    National Park Service, Department of the Interior — The Canyon de Chelly National Monument Vegetation Map Database was developed as a primary product in the Canyon de Chelly National Monument Vegetation...

  10. Software Configuration Management Plan for the B-Plant Canyon Ventilation Control System

    Energy Technology Data Exchange (ETDEWEB)

    MCDANIEL, K.S.

    1999-08-31

    Project W-059 installed a new B Plant Canyon Ventilation System. Monitoring and control of the system is implemented by the Canyon Ventilation Control System (CVCS). This Software Configuration Management Plan provides instructions for change control of the CVCS.

  11. 76 FR 22670 - Black Hills National Forest, Hell Canyon Ranger District, South Dakota, Vestal Project

    Science.gov (United States)

    2011-04-22

    ... Forest Service Black Hills National Forest, Hell Canyon Ranger District, South Dakota, Vestal Project..., District Ranger, Black Hills National Forest, Hell Canyon Ranger District, 330 Mount Rushmore Road, Custer, South Dakota 57730. Telephone Number: (605) 673- 4853. E-mail:...

  12. Samples from the Georges Bank Canyons acquired in 1936 (STETSON36 shapefile)

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — Submarine canyons cut into the edge of the continental shelf and the continental slope along much of the U.S. Atlantic coast. Three canyons along the southern edge...

  13. 2011 Pacific Gas and Electric Diablo Canyon Power Plant (DCPP): Los Osos, CA Central Coast

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Diablo Canyon Power Plant (DCPP) LiDAR and Imagery datasets are comprised of three separate LiDAR surveys: Diablo Canyon (2010), Los Osos (2011), and San Simeon...

  14. 2013 Pacific Gas and Electric Diablo Canyon Power Plant (DCPP): San Simeon, CA Central Coast

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Diablo Canyon Power Plant (DCPP) LiDAR and Imagery datasets are comprised of three separate LiDAR surveys: Diablo Canyon (2010), Los Osos (2011), and San Simeon...

  15. Data from Oceanographer, Lydonia, and Gilbert Canyons acquired in 1965 (SCHWARTZ65 shapefile)

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — Submarine canyons occur at the edge of the continental shelf and cut across the slope and rise along the U.S. east coast. Three of these canyons (Oceanographer,...

  16. Diffraction of plane P waves by a canyon of arbitrary shape in poroelastic half-space (Ⅰ): Formulation

    Institute of Scientific and Technical Information of China (English)

    Jianwen Liang; Zhongxian Liu

    2009-01-01

    This paper presents an indirect boundary integration equation method for diffraction of plane P waves by a two-dimensional canyon of arbitrary shape in poroelastic half-space. The Green's functions of compressional and shear wave sources in poroelastic half-space are derived based on Biot's theory. The scattered waves are constructed using the fictitious wave sources close to the boundary of the canyon, and magnitude of the fictitious wave sources are determined by the boundary conditions. The precision of the method is verified by the satisfaction extent of boundary conditions, the comparison between the degenerated solutions of single-phased half-space and the well-known solutions, and the numerical stability of the method.

  17. Renewable Energy Essentials: Wind

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    Subjects for further research, specific to wind energy technology, include more refined resource assessment; materials with higher strength to mass ratios; advanced grid integration and power quality and control technologies; standardisation and certification; development of low-wind regime turbines; improved forecasting; increased fatigue resistance of major components such as gearboxes; better models for aerodynamics and aeroelasticity; generators based on superconductor technology; deep-offshore foundations; and high-altitude 'kite' concepts.

  18. Regional economic impacts of Grand Canyon river runners.

    Science.gov (United States)

    Hjerpe, Evan E; Kim, Yeon-Su

    2007-10-01

    Economic impact analysis (EIA) of outdoor recreation can provide critical social information concerning the utilization of natural resources. Outdoor recreation and other non-consumptive uses of resources are viewed as environmentally friendly alternatives to extractive-type industries. While outdoor recreation can be an appropriate use of resources, it generates both beneficial and adverse socioeconomic impacts on rural communities. The authors used EIA to assess the regional economic impacts of rafting in Grand Canyon National Park. The Grand Canyon region of northern Arizona represents a rural US economy that is highly dependent upon tourism and recreational expenditures. The purpose of this research is twofold. The first is to ascertain the previously unknown regional economic impacts of Grand Canyon river runners. The second purpose is to examine attributes of these economic impacts in terms of regional multipliers, leakage, and types of employment created. Most of the literature on economic impacts of outdoor recreation has focused strictly on the positive economic impacts, failing to illuminate the coinciding adverse and constraining economic impacts. Examining the attributes of economic impacts can highlight deficiencies and constraints that limit the economic benefits of recreation and tourism. Regional expenditure information was obtained by surveying non-commercial boaters and commercial outfitters. The authors used IMPLAN input-output modeling to assess direct, indirect, and induced effects of Grand Canyon river runners. Multipliers were calculated for output, employment, and income. Over 22,000 people rafted on the Colorado River through Grand Canyon National Park in 2001, resulting in an estimated $21,100,000 of regional expenditures to the greater Grand Canyon economy. However, over 50% of all rafting-related expenditures were not captured by the regional economy and many of the jobs created by the rafting industry are lower-wage and seasonal. Policy

  19. 76 FR 54487 - Charter Renewal, Glen Canyon Dam Adaptive Management Work Group

    Science.gov (United States)

    2011-09-01

    ... Bureau of Reclamation Charter Renewal, Glen Canyon Dam Adaptive Management Work Group AGENCY: Bureau of... the Glen Canyon Dam Adaptive Management Work Group. The purpose of the Adaptive Management Work Group... of the Glen Canyon Dam Adaptive Management Work Group is in the public interest in connection...

  20. 78 FR 54482 - Charter Renewal, Glen Canyon Dam Adaptive Management Work Group

    Science.gov (United States)

    2013-09-04

    ... Bureau of Reclamation Charter Renewal, Glen Canyon Dam Adaptive Management Work Group AGENCY: Bureau of... the Glen Canyon Dam Adaptive Management Work Group. The purpose of the Adaptive Management Work Group... Canyon Dam Adaptive Management Work Group is in the public interest in connection with the performance...