WorldWideScience

Sample records for canadian nuclear facilities

  1. AECL's strategy for decommissioning Canadian nuclear facilities

    Joubert, W.M.; Pare, F.E.; Pratapagiri, G.

    1992-01-01

    The Canadian policy on decommissioning of nuclear facilities as defined in the Atomic Energy Control Act and Regulations is administered by the Atomic Energy Control Board (AECB), a Federal Government agency. It requires that these facilities be decommissioned according to approved plans which are to be developed by the owner of the nuclear facility during its early stages of design and to be refined during its operating life. In this regulatory environment, Atomic Energy of Canada (AECL) has developed a decommissioning strategy for power stations which consists of three distinctive phases. After presenting AECL's decommissioning philosophy, its foundations are explained and it is described how it has and soon will be applied to various facilities. A brief summary is provided of the experience gained up to date on the implementation of this strategy. (author) 3 figs.; 1 tab

  2. Radiocarbon dispersion around Canadian nuclear facilities

    Milton, G.M.; Kramer, S.J.; Brown, R.M.; Repta, C.J.W.; King, K.J.; Rao, R.R.

    1995-01-01

    Canadian deuterium uranium (CANDU) pressurized heavy-water reactors produce 14 C by neutron activation of trace quantities of nitrogen in annular gas and reactor components ( 14 N(n,p) 14 C), and from 17 O in the heavy water moderator by ( 17 O(n,α) 14 C). The radiocarbon produced in the moderator is removed on ion exchange resins incorporated in the water purification systems; however, a much smaller gaseous portion is vented from reactor stacks at activity levels considerably below 1% of permissible derived emission limits. Early measurements of the carbon speciation indicated that >90% of the 14 C emitted was in the form of CO 2 .We conducted surveys of the atmospheric dispersion of 14 CO 2 at the Chalk River Laboratories and at the Pickering Nuclear Generating Station. We analyzed air, vegetation, soils and tree rings to add to the historical record of 14 C emissions at these sites, and to gain an understanding of the relative importance of the various carbon pools that act as sources/sinks within the total 14 C budget. Better model parameters than those currently available for calculating the dose to the critical group can be obtained in this manner. Global dose estimates may require the development of techniques for estimating emissions occurring outside the growing season. (author)

  3. Childhood leukaemia around Canadian nuclear facilities. Phase 1

    Clarke, E.A.; McLaughlin, J.; Anderson, T.W.

    1989-05-01

    A ninefold excess risk of leukaemia, as observed in vicinity of the Sellafield facility, was not observed amongst children born to mothers residing in the areas around nuclear research facilities and uranium mining, milling and refining facilities in Ontario. In the vicinity of nuclear research facilities, the rate of leukaemia was, in fact, less than expected. In the areas around the uranium mining, milling and refining facilities; leukaemia occurred slightly more frequently than expected; however, due to small frequencies these results may have risen by chance. A slightly greater than expected occurrence of leukaemia was also detected, which may well have been due to chance, in an exploratory study of the areas around nuclear power generating stations in Ontario

  4. Childhood leukaemia around Canadian nuclear facilities. Phase 2

    Clarke, E.A.; McLaughlin, J.; Anderson, T.W.

    1991-06-01

    Prompted by findings of increased occurrence of childhood leukaemia in the vicinity of some nuclear facilities in the United Kingdom, this study aimed to investigate whether the frequency of leukaemia among children born to mothers living near nuclear facilities in Ontario differed from the provincial average. The Ontario Cancer Registry was used to identify 1894 children aged 0 to 14 years who died from leukaemia between 1950 and 1987, and 1814 children who were diagnosed with leukaemia between 1964 and 1986. Residence at birth and death was obtained from birth and death certificates. Analyses were performed separately for nuclear research and development facilities; uranium mining, milling and refining facilities; and, nuclear generating stations; and for areas within the same county as the facility and 'nearby' - within a 25-km radius of the facility. Risk estimates were calculated as the ratio of the observed (O) number of events over the expected (E) number. In the vicinity of nuclear research and development facilities the rate of leukaemia was less than expected and within the bound of chance variation. In the areas around the uranium mining, milling and refining facilities and nuclear power plants leukaemia occurred slightly more frequently than expected, but due to small frequencies these differences may have arisen due to chance. Large differences between observed and expected rates were not detected around any of the Ontario facilities. This study was large enough to detect excess risks of the magnitude reported in the United Kingdom, but it was not large enough to discriminate between the observed relative risks and a chance finding. Levels of leukaemia detected near nuclear generating stations indicate the need for further investigation. (20 tabs., 15 figs., 32 refs.)

  5. Managing LLRW from decommissioning of nuclear facilities - a Canadian perspective

    Donders, R E [Atomic Energy of Canada Ltd., Chalk River, ON (Canada). Chalk River Nuclear Labs.; Hardy, D G [Frontenac Consulting Services, Deep River, ON (Canada); De, P L [Low-Level Radioactive Waste Management Office, Gloucester, ON (Canada)

    1994-03-01

    In Canada, considerable experience has been gained recently in decommissioning nuclear facilities and managing the resulting waste. This experience has raised important issues from both the decommissioning and waste management perspectives. This paper focuses on the waste management aspects of decommissioning. Past experience is reviewed, preliminary estimates of waste volumes and characteristics are provided, and the major technical and regulatory issues are discussed. (author). 5 refs., 1 tab., 2 figs.

  6. The management of carbon-14 in Canadian nuclear facilities

    1995-07-01

    In Canada, Derived Emission Limits (DELs) for the release of radionuclides from nuclear facilities are set to ensure that the dose to a member of a critical group from one year's release does not exceed the limit on annual dose to a member of the public set by the Atomic Energy Control Regulations. The Advisory Committee on Radiological Protection (ACRP) has expressed concerns as to whether this procedure provides adequate protection to members of the public, including future generations, for certain radionuclides such as a carbon-14 ( 14 C), which can accumulate in the environment and which can be dispersed, through environmental processes, beyond the local region where the critical group is assumed to live. The ACRP subsequently established a Working Group to review the production, release, environmental levels, and waste management of 14 C arising in CANDU power reactors. The ACRP recommendations resulting from this review can be summarized as · Given the current levels of emissions from CANDU nuclear power stations resulting from the use of a carbon dioxide annulus gas and the limitations in the calculation and use of collective dose, the ACRP sees no need for and additional collective dose limit to be applied to these sources. · The AECB should require licensees of power reactors and waste management sites to provide an annual inventory of 14 C held within reactor buildings and waste management sites; to provide information on the stability of the ion exchange resins and their continuing ability to retain the 14 C; to demonstrate on an ongoing basis that releases of 14 C are maintained at a small fraction of the emission limits; and to report annually the critical group and local collective doses arising from releases of 14 C. 61 refs., 25 tabs., 4 figs

  7. Canadian development program for off-gas management in nuclear facilities

    Sridhar, T.S.

    1983-01-01

    The Canadian program for the development and evaluation of processes and technology for the separation and containment of radioactive species in off-gases is directed towards the following specific aspects: 1) assessment of available treatment technology and evaluation of future clean-up requirements; 2) development and engineering evaluation, under realistic conditions, of promising new processes that would be inherently simpler and safer; and 3) specification of off-gas emission control systems for future nuclear facilities based on the most favourable technology. The program is being carried out by Atomic Energy of Canada Limited in collaboration with the electrical utility, Ontario Hydro, and selected Canadian universities. A brief description is presented of methods for removing tritium and carbon-14 from the moderator systems of CANDU power reactors, methods for removing iodine from the off-gases of a molybdenum-99 production facility at the Chalk River Nuclear Laboratories, and procedures for monitoring the off-gas effluent composition in the Thorium Fuel Reprocessing Experiment (TFRE) facility at the Whiteshell Nuclear Research Establishment

  8. Conditioning and handling of tritiated wastes at Canadian nuclear power facilities

    Krochmalnek, L.S.; Krasznai, J.P.; Carney, M.

    1987-04-01

    Ontario Hydro operates a 10,000 MW capacity nuclear power system utilizing the CANDU pressurized heavy water reactor design. The use of D 2 O as moderator and coolant results in the production of about 2400 Ci of tritium per MWe-yr. As a result, there is significant Canadian experience in the treatment, handling, transport and storage of tritiated wastes. Ontario Hydro operates its own reactor waste storage site which includes systems for volume reduction, immobilization and packaging of wastes. In addition, a facility to remove tritium from heavy water is presently being commissioned at the Darlington nuclear site. This facility will generate tritiated liquid and solid waste that will have to be properly conditioned prior to storage or disposal. The nature of these various wastes and the processes/packaging required to meet storage/disposal criteria are judged to have relevance to investigations in fusion facility waste arisings. Experience to date, planned operational procedures and ongoing R and D in this area are described

  9. Radiological environmental monitoring programs at Canadian nuclear facilities - a practical model for follow-up activities under the Canadian Environmental Assessment Act

    Tamm, J.A.; Zach, R.

    2000-01-01

    Under the Canadian Environmental Assessment Act (the Act), a federal authority, if it considers it appropriate, is to design a follow-up program for a project undergoing a federal environmental assessment and arrange for implementation of that program. Under the Act a follow-up program means a set of activities for verifying the accuracy of the environmental assessment (EA) of a project and for determining the effectiveness of any measures taken to mitigate any adverse environmental effects resulting from the project. The Act currently does not include regulations, guidelines, standards or procedures regarding the design, content and implementation requirements for follow-up programs (Canadian Environmental Assessment Agency [the Agency] 1999). Uncertainties also exist regarding the roles and responsibilities in designing, implementing, enforcing and auditing such activities. The Agency is presently specifying appropriate activities to address these issues. This paper considers the existing radiological environmental monitoring programs at nuclear facilities. Such programs consist of two types of monitoring-radioactivity releases from the facility via liquid and gaseous waste streams, and radioactivity in the environment at large, beyond the facility's immediate location. Such programs have been developed by AECL, Canadian nuclear utilities and uranium mining companies. Our analysis show that these programs can provide a good model for follow-up programs under the Act. (author)

  10. Canadian nuclear risk experience

    Hamel, P.E.

    1982-05-01

    Risk assessment in the Canadian nuclear fuel cycle is a very important and complex subject. Many levels of government are involved in deciding the acceptable limits for the risks, taking into account the benefits for society [fr

  11. Canadian Nuclear Association

    Reid, John

    1992-01-01

    It is the view of the Canadian Nuclear Association that continuing creation of economic wealth is vital to sustainable development. A plentiful supply of cheap energy is essential. Nuclear energy provides the cleanest source of bulk energy generation essential to any path of sustainable development

  12. Issues related to the construction and operation of a geological disposal facility for nuclear fuel waste in crystalline rock - the Canadian experience

    Allan, C.J.; Baumgartner, P.; Ohta, M.M.; Simmons, G.R.; Whitaker, S.H. [Atomic Energy of Canada Ltd., Pinawa, MB (Canada). Whiteshell Labs

    1997-12-31

    This paper covers the overview of the Canadian nuclear fuel waste management program, the general approach to the siting, design, construction, operation and closure of a geological disposal facility, the implementing disposal, and the public involvement in implementing geological disposal of nuclear fuel waste. And two appendices are included. 45 refs., 5 tabs., 10 figs.

  13. Issues related to the construction and operation of a geological disposal facility for nuclear fuel waste in crystalline rock - the Canadian experience

    Allan, C.J.; Baumgartner, P.; Ohta, M.M.; Simmons, G.R.; Whitaker, S.H.

    1997-01-01

    This paper covers the overview of the Canadian nuclear fuel waste management program, the general approach to the siting, design, construction, operation and closure of a geological disposal facility, the implementing disposal, and the public involvement in implementing geological disposal of nuclear fuel waste. And two appendices are included. 45 refs., 5 tabs., 10 figs

  14. The Canadian Nuclear Safety Commission regulatory process for decommissioning a uranium mining facility

    Scissons, K.; Schryer, D.M.; Goulden, W.; Natomagan, C.

    2002-01-01

    The Canadian Nuclear Safety Commission (CNSC) regulates uranium mining in Canada. The CNSC regulatory process requires that a licence applicant plan for and commit to future decommissioning before irrevocable decisions are made, and throughout the life of a uranium mine. These requirements include conceptual decommissioning plans and the provision of financial assurances to ensure the availability of funds for decommissioning activities. When an application for decommissioning is submitted to the CNSC, an environmental assessment is required prior to initiating the licensing process. A case study is presented for COGEMA Resources Inc. (COGEMA), who is entering the decommissioning phase with the CNSC for the Cluff Lake uranium mine. As part of the licensing process, CNSC multidisciplinary staff assesses the decommissioning plan, associated costs, and the environmental assessment. When the CNSC is satisfied that all of its requirements are met, a decommissioning licence may be issued. (author)

  15. Shared Facilities Canadian Style.

    Galonski, Mark A.

    1998-01-01

    Describes two projects arising from an Ontario (Canada) Ministry of Education initiative that combined school and nonschool capital funds to build joint facilities. The Stratford Education and Recreation Centre and the Humberwood Community Centre demonstrate that government agencies can cooperate to benefit the community. Success depends on having…

  16. Canadian attitudes to nuclear power

    Davies, J.E.O.

    1977-01-01

    In the past ten years, public interest in nuclear power and its relationship to the environment has grown. Although most Canadians have accepted nuclear power as a means of generating electricity, there is significant opposition to its use. This opposition has effectively forced the Canadian nuclear industry to modify its behaviour to the public in the face of growing concern over the safety of nuclear power and related matters. The paper reviews Canadian experience concerning public acceptance of nuclear power, with special reference to the public information activities of the Canadian nuclear industry. Experience has shown the need for scientific social data that will permit the nuclear industry to involve the public in a rational examination of its concern about nuclear power. The Canadian Nuclear Association sponsored such studies in 1976 and the findings are discussed. They consisted of a national assessment of public attitudes, two regional studies and a study of Canadian policy-makers' views on nuclear energy. The social data obtained were of a base-line nature describing Canadian perceptions of and attitudes to nuclear power at that time. This research established that Canadian levels of knowledge about nuclear power are very low and that there are marked regional differences. Only 56% of the population have the minimum knowledge required to indicate that they know that nuclear power can be used to generate electricity. Nevertheless, 21% of informed Canadians oppose nuclear power primarily on the grounds that it is not safe. Radiation and waste management are seen to be major disadvantages. In perspective, Canadians are more concerned with inflation than with the energy supply. About half of all Canadians see the question of energy supplies as a future problem (within five years), not a present one. A more important aspect of energy is seen by the majority of Canadians to be some form of energy independence. The use of data from these studies is no easy

  17. A proposed regulatory policy statement on human factors requirements in the design and operation of Canadian nuclear facilities

    1986-10-01

    With the increasing complexity of new nuclear facilities and the extent to which automation is being applied, it is essential that the staff who operate a facility be considered as integral components in the design and safety analyses. This policy statement is proposed to indicate those areas of facility design and operation where the role of the human operator must be especially examined

  18. Nuclear facilities

    Anon.

    2000-01-01

    Here is given the decree (2000-1065) of the 25. of October 2000 reporting the publication of the convention between the Government of the French Republic and the CERN concerning the safety of the LHC (Large Hadron Collider) and the SPS (Proton Supersynchrotron) facilities, signed in Geneva on July 11, 2000. By this convention, the CERN undertakes to ensure the safety of the LHC and SPS facilities and those of the operations of the LEP decommissioning. The French legislation and regulations on basic nuclear facilities (concerning more particularly the protection against ionizing radiations, the protection of the environment and the safety of facilities) and those which could be decided later on apply to the LHC, SPS and auxiliary facilities. (O.M.)

  19. Canadian attitudes to nuclear power

    Davies, J.E.O.; Dobson, J.K.; Baril, R.G.

    1977-05-01

    A national assessment was made of public attitudes towards nuclear power, along with regional studies of the Maritimes and mid-western Canada and a study of Canadian policy-makers' views on nuclear energy. Public levels of knowledge about nuclear power are very low and there are marked regional differences. Opposition centers on questions of safety and is hard to mollify due to irrational fear and low institutional credibility. Canadians rate inflation as a higher priority problem than energy and see energy shortages as a future problem (within 5 years) and energy independence as a high priority policy. (E.C.B.)

  20. Nuclear regulation - the Canadian approach

    Jennekens, J.

    1981-09-01

    Although the Atomic Energy Control Board was established 35 years ago the basic philosophy of nuclear regulation in Canada and the underlying principles of the regulatory process remain essentially unchanged. This paper outlines the Canadian approach to nuclear regulation and explains in practical terms how the principles of regulation are applied. (author)

  1. Certification of Canadian nuclear power plant personnel

    Newbury, F.

    2014-01-01

    The Canadian Nuclear Safety Commission (CNSC) regulates the use of nuclear energy and materials to protect health, safety, security of Canadians and the environment, and to implement Canada's international commitments on the peaceful use of nuclear energy. As part of its mandate, the CNSC requires certification of those who work in positions with direct impact on the safety of Canadian nuclear power plants (NPPs) and research reactors. Other positions, such as exposure device operators and radiation safety officers at other nuclear facilities, also require CNSC certification. In this paper, the certification process of Canadian NPP personnel will be examined. In keeping with the CNSC's regulatory philosophy and international practice, licensees bear the primary responsibility for the safe operation of their NPPs. They are therefore held entirely responsible for training and testing their workers, in accordance with applicable regulatory requirements, to ensure they are fully qualified to perform their duties. The CNSC obtains assurance that all persons it certifies are qualified to carry out their respective duties. It achieves this by overseeing a regime of licensee training programs and certification examinations, which are based on a combination of appropriate regulatory guidance and compliance activities. Reviews of the knowledge-based certification examination methodology and of lessons learned from Fukushima have generated initiatives to further strengthen the CNSC's certification programs for NPP workers. Two of those initiatives are discussed in this paper. (author)

  2. Nuclear facilities

    Anon.

    2002-01-01

    During September and October 2001, 15 events were recorded on the first grade and 1 on the second grade of the INES scale. The second grade event is in fact a re-classification of an incident that occurred on the second april 2001 at Dampierre power plant. This event happened during core refueling, a shift in the operation sequence led to the wrong positioning of 113 assemblies. A preliminary study of this event shows that this wrong positioning could have led, in other circumstances, to the ignition of nuclear reactions. Even in that case, the analysis made by EDF shows that the consequences on the staff would have been limited. Nevertheless a further study has shown that the existing measuring instruments could not have detected the power increase announcing the beginning of the chain reaction. The investigation has shown that there were deficiencies in the control of the successive operations involved in refueling. EDF has proposed a series of corrective measures to be implemented in all nuclear power plants. The other 15 events are described in the article. During this period 121 inspections have been made in nuclear facilities. (A.C.)

  3. Levels of tritium in soils and vegetation near Canadian nuclear facilities releasing tritium to the atmosphere: implications for environmental models

    Thompson, P.A.; Kwamena, N.-O.A.; Ilin, M.; Wilk, M.; Clark, I.D.

    2015-01-01

    Concentrations of organically bound tritium (OBT) and tritiated water (HTO) were measured over two growing seasons in vegetation and soil samples obtained in the vicinity of four nuclear facilities and two background locations in Canada. At the background locations, with few exceptions, OBT concentrations were higher than HTO concentrations: OBT/HTO ratios in vegetation varied between 0.3 and 20 and values in soil varied between 2.7 and 15. In the vicinity of the four nuclear facilities OBT/HTO ratios in vegetation and soils deviated from the expected mean value of 0.7, which is used as a default value in environmental transfer models. Ratios of the OBT activity concentration in plants ([OBT] plant ) to the OBT activity concentration in soils ([OBT] soil ) appear to be a good indicator of the long-term behaviour of tritium in soil and vegetation. In general, OBT activity concentrations in soils were nearly equal to OBT activity concentrations in plants in the vicinity of the two nuclear power plants. [OBT] plant /[OBT] soil ratios considerably below unity observed at one nuclear processing facility represents historically higher levels of tritium in the environment. The results of our study reflect the dynamic nature of HTO retention and OBT formation in vegetation and soil during the growing season. Our data support the mounting evidence suggesting that some parameters used in environmental transfer models approved for regulatory assessments should be revisited to better account for the behavior of HTO and OBT in the environment and to ensure that modelled estimates (e.g., plant OBT) are appropriately conservative. - Highlights: • We measured tritium in soils and plants near four nuclear facilities in Canada. • OBT/HTO ratios in plants are higher than default value in environmental models. • OBT/HTO ratios in background soils reflect historically higher atmospheric tritium. • Implications for environmental transfer models are discussed

  4. The Canadian nuclear power industry. Background paper

    Nixon, A.

    1993-12-01

    Nuclear power, the production of electricity from uranium through nuclear fission, is by far the most prominent segment of the nuclear industry. The value of the electricity produced, $3.7 billion in Canada in 1992, far exceeds the value of any other product of the civilian nuclear industry. Power production employs many more people than any other sector, the capital investment is much greater, and nuclear power plants are much larger and more visible than uranium mining and processing facilities. They are also often located close to large population centres. This paper provides an overview of some of the enormously complex issues surrounding nuclear power. It describes the Canadian nuclear power industry, addressing i particular its performance so far and future prospects. (author). 1 tab

  5. The Canadian nuclear power industry. Background paper

    Nixon, A [Library of Parliament, Ottawa, ON (Canada). Science and Technology Div.

    1993-12-01

    Nuclear power, the production of electricity from uranium through nuclear fission, is by far the most prominent segment of the nuclear industry. The value of the electricity produced, $3.7 billion in Canada in 1992, far exceeds the value of any other product of the civilian nuclear industry. Power production employs many more people than any other sector, the capital investment is much greater, and nuclear power plants are much larger and more visible than uranium mining and processing facilities. They are also often located close to large population centres. This paper provides an overview of some of the enormously complex issues surrounding nuclear power. It describes the Canadian nuclear power industry, addressing i particular its performance so far and future prospects. (author). 1 tab.

  6. Levels of tritium in soils and vegetation near Canadian nuclear facilities releasing tritium to the atmosphere: implications for environmental models.

    Thompson, P A; Kwamena, N-O A; Ilin, M; Wilk, M; Clark, I D

    2015-02-01

    Concentrations of organically bound tritium (OBT) and tritiated water (HTO) were measured over two growing seasons in vegetation and soil samples obtained in the vicinity of four nuclear facilities and two background locations in Canada. At the background locations, with few exceptions, OBT concentrations were higher than HTO concentrations: OBT/HTO ratios in vegetation varied between 0.3 and 20 and values in soil varied between 2.7 and 15. In the vicinity of the four nuclear facilities OBT/HTO ratios in vegetation and soils deviated from the expected mean value of 0.7, which is used as a default value in environmental transfer models. Ratios of the OBT activity concentration in plants ([OBT]plant) to the OBT activity concentration in soils ([OBT]soil) appear to be a good indicator of the long-term behaviour of tritium in soil and vegetation. In general, OBT activity concentrations in soils were nearly equal to OBT activity concentrations in plants in the vicinity of the two nuclear power plants. [OBT]plant/[OBT]soil ratios considerably below unity observed at one nuclear processing facility represents historically higher levels of tritium in the environment. The results of our study reflect the dynamic nature of HTO retention and OBT formation in vegetation and soil during the growing season. Our data support the mounting evidence suggesting that some parameters used in environmental transfer models approved for regulatory assessments should be revisited to better account for the behavior of HTO and OBT in the environment and to ensure that modelled estimates (e.g., plant OBT) are appropriately conservative. Crown Copyright © 2014. Published by Elsevier Ltd. All rights reserved.

  7. Conference summaries. Canadian Nuclear Association 29. annual conference; Canadian Nuclear Society 10. annual conference

    1989-01-01

    Separate abstracts were prepared for 15 papers from the twenty-ninth Annual Conference of the Canadian Nuclear Association. Abstracts were also prepared for the 102 papers from the tenth Annual Conference of the Canadian Nuclear Society

  8. Conference summaries. Canadian Nuclear Association 29. annual conference; Canadian Nuclear Society 10. annual conference

    NONE

    1990-12-31

    Separate abstracts were prepared for 15 papers from the twenty-ninth Annual Conference of the Canadian Nuclear Association. Abstracts were also prepared for the 102 papers from the tenth Annual Conference of the Canadian Nuclear Society.

  9. Nuclear communications : A Canadian perspective

    Macpherson, John A.

    1994-01-01

    Times have changed since the early days of nuclear energy when it was a symbol of a brave new world, Public information strategies have evolved to meet increasing public concerns, and have shifted from being a largely unfocused attempt at publicity to being more concerned with managing issues and solving problems. This paper describes some of the salient features of the Canadian experience in nuclear communications and examines four key aspects: opinion and attitude research; media relations; coeducation; and advertising. It also addresses the challenge of responding to the allegations and tactics of those who are actively hostile to nuclear energy, and recommends that the principles of Total Quality Management and of organizational effectiveness be applied more thorough and more consistently to the public affairs function

  10. Canadian national nuclear forensics capability project

    Ball, J.; Dimayuga, I.; Summerell, I.; Totland, M.; Jonkmans, G.; Whitlock, J.; El-jaby, A.; Inrig, E.

    2015-01-01

    Following the 2010 Nuclear Security Summit, Canada expanded its existing capability for nuclear forensics by establishing a national nuclear forensics laboratory network, which would include a capability to perform forensic analysis on nuclear and other radioactive material, as well as on traditional evidence contaminated with radioactive material. At the same time, the need for a national nuclear forensics library of signatures of nuclear and radioactive materials under Canadian regulatory control was recognized. The Canadian Safety and Security Program, administered by Defence Research and Development Canada's Centre for Security Science (DRDC CSS), funds science and technology initiatives to enhance Canada's preparedness for prevention of and response to potential threats. DRDC CSS, with assistance from Canadian Nuclear Laboratories, formerly Atomic Energy of Canada Limited, is leading the Canadian National Nuclear Forensics Capability Project to develop a coordinated, comprehensive, and timely national nuclear forensics capability. (author)

  11. Canadian national nuclear forensics capability project

    Ball, J.; Dimayuga, I., E-mail: joanne.ball@cnl.ca [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); Summerell, I. [Royal Canadian Mounted Police, Ottawa, Ontario (Canada); Totland, M. [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); Jonkmans, G. [Defence Research and Development Canada, Ottawa, Ontario (Canada); Whitlock, J. [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); El-jaby, A. [Canadian Nuclear Safety Commission, Ottawa, Ontario (Canada); Inrig, E. [Defence Research and Development Canada, Ottawa, Ontario (Canada)

    2015-06-15

    Following the 2010 Nuclear Security Summit, Canada expanded its existing capability for nuclear forensics by establishing a national nuclear forensics laboratory network, which would include a capability to perform forensic analysis on nuclear and other radioactive material, as well as on traditional evidence contaminated with radioactive material. At the same time, the need for a national nuclear forensics library of signatures of nuclear and radioactive materials under Canadian regulatory control was recognized. The Canadian Safety and Security Program, administered by Defence Research and Development Canada's Centre for Security Science (DRDC CSS), funds science and technology initiatives to enhance Canada's preparedness for prevention of and response to potential threats. DRDC CSS, with assistance from Canadian Nuclear Laboratories, formerly Atomic Energy of Canada Limited, is leading the Canadian National Nuclear Forensics Capability Project to develop a coordinated, comprehensive, and timely national nuclear forensics capability. (author)

  12. How Canadians feel about nuclear energy

    Anon.

    1989-01-01

    A survey conducted by Decima Research in April 1989 showed that 50% of Canadians were somewhat or strongly in favour of nuclear energy, the percentage varying from 37% in British Columbia to 65% in Ontario. A majority (56%) questioned the nuclear industry's ability to handle its waste safely, but 45% believed that it was working hard to solve the problem. It was evident that an advertising campaign by the Canadian Nuclear Association had an effect

  13. The Canadian nuclear industry - a national asset

    1985-03-01

    The economic importance of the Canadian nuclear industry in saving costs and creating jobs is expounded. The medical work of Atomic Energy of Canada Limited is also extolled. The Canadian Nuclear Association urges the federal government to continue to support the industry at home, and to continue to promote nuclear exports. This report was prepared in response to the Federal Finance Minister's 'A New Direction for Canada'

  14. The Canadian Centre for Nuclear Innovation

    Root, J., E-mail: John.Root@usask.ca [Canadian Centre for Nuclear Innovation, Inc., Saskatoon, Saskatchewan (Canada)

    2013-07-01

    The Canadian Centre for Nuclear Innovation (CCNI) was incorporated on December 20, 2011, to help place Saskatchewan among global leaders of nuclear research, development and training, through investment in partnerships with academia and industry for maximum societal and economic benefit. As the CCNI builds a community of participants in the nuclear sector, the province of Saskatchewan expects to see positive impacts in nuclear medicine, materials research, nuclear energy, environmental responsibility and the quality of social policy related to nuclear science and technology. (author)

  15. Nuclear power and the Canadian public

    Greer-Wootten, B; Mitson, L

    1976-06-01

    The purpose of the study was to ascertain the opinions and attitudes of Canadians to the use of nuclear power for generating electricity, as an initial step in developing information programs attuned to the demonstrated needs of the public. This report presents the findings from the survey of the Canadian public aged 18 years and over. Over 2100 persons responded to our interviewers, generating about 200,000 answers to the questions.

  16. Canadian approach to nuclear power safety

    Atchison, R.J.; Boyd, F.C.; Domaratzki, Z.

    1983-01-01

    The development of the Canadian nuclear power safety philosophy and practice is traced from its early roots at the Chalk River Nuclear Laboratories to the licensing of the current generation of power reactors. Basic to the philosophy is a recognition that the licensee is primarily responsible for achieving a high standard safety. As a consequence, regulatory requirements have emphasized numerical safety goals and objectives and minimized specific design or operating rules. In this article the Canadian licensing process is described with a discussion of some of the difficulties encountered. Examples of specific licensing considerations for each phase of a project are included

  17. The Canadian nuclear fuel waste management program

    Rummery, T.E.; Rosinger, E.L.J.

    1983-05-01

    The Canadian Nuclear Fuel Waste Management Program is now well established. This report outlines the generic research and technological development underway in this program to assess the concept of immobilization and subsequent disposal of nuclear fuel waste deep in a stable plutonic rock in the Canadian Shield. The program participants, funding, schedule and associated external review processes are briefly outlined. The major scientific and engineering components of the program, namely, immobilization studies, geoscience research and environmental and safety assessment, are described in more detail

  18. The Canadian approach to nuclear power safety

    Atchison, R.J.; Boyd, F.C.; Domaratski, Z.

    1983-07-01

    The development of the Canadian nuclear power safety philosophy and practice is traced from its early roots at the Chalk River Nuclear Laboratory to the licensing of the current generation of power reactors. Basic to the philosophy is a recognition that the primary responsibility for achieving a high standard of safety resides with the licensee. As a consequence, regulatory requirements have emphasized numerical safety goals and objectives and minimized specific design or operating rules. The Canadian licensing process is described along with a discussion of some of the difficulties encountered. Examples of specific licensing considerations for each phase of a project are included

  19. The Canadian nuclear scene - a 1983 perspective

    Foulkes, F.M.

    1983-01-01

    The author reviews the previous year's performance and future prospects for the Canadian nuclear industry. Continued economic difficulties have meant continued streamlining of the industry. Basic strength is still the year-after-year record performance of the Ontario Hydro CANDU units. Given this performance, flexibility in the structure of the industry, and strong government support commercial success can be achieved eventually

  20. Nuclear physics accelerator facilities

    1988-12-01

    This paper describes many of the nuclear physics heavy-ion accelerator facilities in the US and the research programs being conducted. The accelerators described are: Argonne National Laboratory--ATLAS; Brookhaven National Laboratory--Tandem/AGS Heavy Ion Facility; Brookhaven National Laboratory--Relativistic Heavy Ion Collider (RHIC) (Proposed); Continuous Electron Beam Accelerator Facility; Lawrence Berkeley Laboratory--Bevalac; Lawrence Berkeley Laboratory--88-Inch Cyclotron; Los Alamos National Laboratory--Clinton P. Anderson Meson Physics Facility (LAMPF); Massachusetts Institute of Technology--Bates Linear Accelerator Center; Oak Ridge National Laboratory--Holifield Heavy Ion Research Facility; Oak Ridge National Laboratory--Oak Ridge Electron Linear Accelerator; Stanford Linear Accelerator Center--Nuclear Physics Injector; Texas AandM University--Texas AandM Cyclotron; Triangle Universities Nuclear Laboratory (TUNL); University of Washington--Tandem/Superconducting Booster; and Yale University--Tandem Van de Graaff

  1. Transfer of Canadian nuclear regulatory technology

    Harvie, J.D.

    1985-10-01

    This paper discusses the Canadian approach to the regulation of nuclear power reactors, and its possible application to CANDU reactors in other countries. It describes the programs which are in place to transfer information on licensing matters to egulatory agencies in other countries, and to offer training on nuclear safety regulation as it is practised in Canada. Experience to date in the transfer of regulatory technology is discussed. 5 refs

  2. The Canadian nuclear fuel waste management program

    Dormuth, K.W.; Nuttall, K.

    1987-01-01

    Canada has established an extensive research program to develop and demonstrate the technology for safely disposing of nuclear fuel waste from Canadian nuclear electric generating stations. The program focuses on the concept of disposal deep in plutonic rock, which is abundant in the province of Ontario, Canada's major producer of nuclear electricity. Research is carried out at field research areas in the Canadian Precambrian Shield, and in government and university laboratories. The schedule calls for a document assessing the disposal concept to be submitted to regulatory and environmental agencies in late 1988. This document will form the basis for a review of the concept by these agencies and by the public. No site selection will be carried out before this review is completed. 10 refs.; 2 figs

  3. Pumps for nuclear facilities

    1999-01-01

    The guide describes how the Finnish Radiation and Nuclear Safety Authority (STUK) controls pumps and their motors at nuclear power plants and other nuclear facilities. The scope of the control is determined by the Safety Class of the pump in question. The various phases of the control are: (1) review of construction plan, (2) control of manufacturing, and construction inspection, (3) commissioning inspection, and (4) control during operation. STUK controls Safety Class 1, 2 and 3 pumps at nuclear facilities as described in this guide. STUK inspects Class EYT (non-nuclear) pumps separately or in connection with the commissioning inspections of the systems. This guide gives the control procedure and related requirements primarily for centrifugal pumps. However, it is also applied to the control of piston pumps and other pump types not mentioned in this guide

  4. Forecasting Canadian nuclear power station construction costs

    Keng, C.W.K.

    1985-01-01

    Because of the huge volume of capital required to construct a modern electric power generating station, investment decisions have to be made with as complete an understanding of the consequences of the decision as possible. This understanding must be provided by the evaluation of future situations. A key consideration in an evaluation is the financial component. This paper attempts to use an econometric method to forecast the construction costs escalation of a standard Canadian nuclear generating station (NGS). A brief review of the history of Canadian nuclear electric power is provided. The major components of the construction costs of a Canadian NGS are studied and summarized. A database is built and indexes are prepared. Based on these indexes, an econometric forecasting model is constructed using an apparently new econometric methodology of forecasting modelling. Forecasts for a period of 40 years are generated and applications (such as alternative scenario forecasts and range forecasts) to uncertainty assessment and/or decision-making are demonstrated. The indexes, the model, and the forecasts and their applications, to the best of the author's knowledge, are the first for Canadian NGS constructions. (author)

  5. Towards a regional siting approach for canadian nuclear fuel waste

    Kuhn, R.G.

    1999-01-01

    The proposal to construct a nuclear fuel waste (NFW) disposal facility in Canada is fraught with difficulties, particularly with respect to gaining public acceptance and consent. Public perceptions of risk associated with a disposal facility are generally negative. Indeed, it was found that over 60% of residents in northern Ontario communities are opposed to the possibility of a disposal facility being constructed within 120 km of their community. Even after being offered the possibility of compensation and incentives, the majority of residents are strongly opposed. Canadian decision makers have generally endorsed a siting framework known as the open siting approach. The major characteristic of this approach is that it allows for substantial public participation in any siting process. It is premised on the notion that only communities where a majority of citizens favour the siting of a facility will be considered as potential hosts. However, given that the majority of residents on the Ontario portion of the Canadian Shield are strongly opposed to a NFW facility, the open approach will not be a panacea for a successful siting process. The major limitation of this approach is the fact that a single community cannot be isolated from its surrounding region and communities. The purpose of this paper is to work towards the development of a regional siting strategy for Canadian nuclear fuel waste management. There are no clear precedents of a regional siting approach to facility location in Canada. However, some analogous planning regimes and initiatives have been attempted. Common to these initiatives is the consideration of a large geographical region and attempts to integrate, at least formally, social, cultural, political and environmental concerns in a coherent and comprehensive manner. Under this type of 'siting strategy' NFW management would be considered within a broad array of resource management initiatives, social and cultural priorities, and institutional

  6. Waste management in Canadian nuclear programs

    Dyne, P.J.

    1975-08-01

    The report describes the wide-ranging program of engineering developments and applications to provide the Canadian nuclear industry with the knowledge and expertise it needs to conduct its waste management program. The need for interim dry storage of spent fuel, and the storage and ultimate disposal of waste from fuel reprocessing are examined. The role of geologic storage in AECL's current waste management program is also considered. (R.A.)

  7. The Canadian nuclear fuel waste management program

    Dixon, R.S.

    1984-12-01

    The Canadian Nuclear Fuel Waste Management Program involves research into the storage and transportation of used nuclear fuel, immobilization of fuel waste, and deep geological disposal of the immobilized waste. The program is now in the fourth year of a ten-year generic research and development phase. The objective of this phase of the program is to assess the safety and environmental aspects of the deep underground disposal of immobilized fuel waste in plutonic rock. The objectives of the research for each component of the program and the progress made to the end of 1983 are described in this report

  8. Adaptation of the ITER facility design to a Canadian site

    Smith, S.

    2001-01-01

    This paper presents the status of Canadian efforts to adapt the newly revised ITER facility design to suit the specific characteristics of the proposed Canadian site located in Clarington, west of Toronto, Ontario. ITER Canada formed a site-specific design team in 1999, comprising participants from three Canadian consulting companies to undertake this work. The technical aspects of this design activity includes: construction planning, geotechnical investigations, plant layout, heat sink design, electrical system interface, site-specific modifications and tie-ins, seismic design, and radwaste management. These areas are each addressed in this paper. (author)

  9. Decommissioning nuclear facilities

    Harmon, K.M.; Jenkins, C.E.; Waite, D.A.; Brooksbank, R.E.; Lunis, B.C.; Nemec, J.F.

    1976-01-01

    This paper describes the currently accepted alternatives for decommissioning retired light water reactor fuel cycle facilities and the current state of decommissioning technology. Three alternatives are recognized: Protective Storage; Entombment; and Dismantling. Application of these alternatives to the following types of facilities is briefly described: light water reactors; fuel reprocessing plants, and mixed oxide fuel fabrication plants. Brief descriptions are given of decommissioning operations and results at a number of sites, and recent studies of the future decommissioning of prototype fuel cycle facilities are reviewed. An overview is provided of the types of operations performed and tools used in common decontamination and decommissioning techniques and needs for improved technology are suggested. Planning for decommissioning a nuclear facility is dependent upon the maximum permitted levels of residual radioactive contamination. Proposed guides and recently developed methodology for development of site release criteria are reviewed. 21 fig, 32 references

  10. Dismantling of nuclear facilities

    Tallec, Michele; Kus, Jean-Pierre; Mogavero, Robert; Genelot, Gabriel

    2009-01-01

    Although the operational life of nuclear plants is long (around 60 years for French reactors) it is nonetheless limited in time, the stopping of it being essentially due to the obsolescence of materials and processes or to economic or safety considerations. The nuclear power plants are then subjected to cleanup and dismantling operations which have different objectives and require specific techniques. The cleanup and/or dismantling of a nuclear power produces significant quantities of waste which is generally of a different nature to that produced during the operation of the concerned plant. The radioactive waste produced by these operations is destined to be sent to the waste disposal facilities of the French National Agency for the Management of Nuclear Waste. (authors)

  11. Robotics for nuclear facilities

    Abe, Akira; Nakayama, Ryoichi; Kubo, Katsumi

    1988-01-01

    It is highly desirable that automatic or remotely controlled machines perform inspection and maintenance tasks in nuclear facilities. Toshiba has been working to develop multi-functional robots, with one typical example being a master-slave manipulator for use in reprocessing facilities. At the same time, the company is also working on the development of multi-purpose intelligent robots. One such device, an automatic inspection robot, to be deployed along a monorail, performs inspection by means of image processing technology, while and advanced intelligent maintenance robot is equipped with a special wheel-locomotion mechanism and manipulator and is designed to perform maintenance tasks. (author)

  12. Canadian involvement in international nuclear cooperation

    Jennekens, Jon.

    1981-01-01

    Since 1945 Canada has been actively involved in the development of an international consensus on measures to prevent the proliferation of nuclear weapons. In parallel with this involvement, Canada has entered into cooperation agreements with several countries under which nuclear materials, equipment and facilities have been supplied in connection with the medical, industrial, agricultural and electrical power applications of nuclear energy. This paper summarizes the actions taken by Canada to encourage the peaceful uses of nuclear energy and to avoid the spread of nuclear weapons [fr

  13. Canadian involvement in international nuclear cooperation

    Jennekens, J.

    1981-01-01

    Since 1945 Canada has been actively involved in the development of an international consensus on measures to prevent the proliferation of nuclear weapons. In parallel with this involvement, Canada has entered into cooperative agreements with several countries under which nuclear materials, equipment and facilities have been supplied in connection with the medical, industrial, agricultural and electrical power applications of nuclear energy. This paper summarizes the actions taken by Canada to encourage the peaceful uses of nuclear energy and to avoid the spread of nuclear weapons. (author)

  14. Nuclear physics accelerator facilities

    1985-01-01

    The Department of Energy's Nuclear Physics program is a comprehensive program of interdependent experimental and theoretical investigation of atomic nuclei. Long range goals are an understanding of the interactions, properties, and structures of atomic nuclei and nuclear matter at the most elementary level possible and an understanding of the fundamental forces of nature by using nuclei as a proving ground. Basic ingredients of the program are talented and imaginative scientists and a diversity of facilities to provide the variety of probes, instruments, and computational equipment needed for modern nuclear research. Approximately 80% of the total Federal support of basic nuclear research is provided through the Nuclear Physics program; almost all of the remaining 20% is provided by the National Science Foundation. Thus, the Department of Energy (DOE) has a unique responsibility for this important area of basic science and its role in high technology. Experimental and theoretical investigations are leading us to conclude that a new level of understanding of atomic nuclei is achievable. This optimism arises from evidence that: (1) the mesons, protons, and neutrons which are inside nuclei are themselves composed of quarks and gluons and (2) quantum chromodynamics can be developed into a theory which both describes correctly the interaction among quarks and gluons and is also an exact theory of the strong nuclear force. These concepts are important drivers of the Nuclear Physics program

  15. Canadian Nuclear Safety Commission's intern program

    Gilmour, P.E.

    2002-01-01

    The Intern Program was introduced at the Canadian Nuclear Safety Commission, Canada's Nuclear Regulator in response to the current competitive market for engineers and scientists and the CNSC's aging workforce. It is an entry level staff development program designed to recruit and train new engineering and science graduates to eventually regulate Canada's nuclear industry. The program provides meaningful work experience and exposes the interns to the general work activities of the Commission. It also provides them with a broad awareness of the regulatory issues in which the CNSC is involved. The intern program is a two-year program focusing on the operational areas and, more specifically, on the generalist functions of project officers. (author)

  16. Issues related to the construction and operation of a geological disposal facility for nuclear fuel waste in crystalline rock - the Canadian experience

    Allan, C.J.; Baumgartner, P.; Ohta, M.M.; Simmons, G.R.; Whitaker, S.H.

    1997-12-01

    The siting, design, construction, operation, decommissioning, and closure of a geological facility for the disposal of nuclear fuel waste is a complex undertaking that will span many decades. Both technical and social issues must be taken into account simultaneously and many factors must be considered. Based on studies carried out in Canada and elsewhere, it appears that these factors can be accommodated and that geological disposal is both technically and socially feasible. But throughout the different stages of implementing disposal, technical and social issues will continue to arise and these will have to be dealt with successfully if progress is to continue. This paper discusses these issues and a proposed approach for dealing with them. (author)

  17. Canadian Experience in Nuclear Power Technology Transfer

    Boulton, J.

    1987-01-01

    Technology transfer has and will continue to play a major role in the development of nuclear power programs. From the early beginnings of the development of the peaceful uses of nuclear power by just a few nations in the mid-1940s there has been a considerable transfer of technology and today 34 countries have nuclear programs in various stages of development. Indeed, some of the major nuclear vendors achieves their present position through a process of technology transfer and subsequent development. Canada, one of the early leaders in the development of nuclear power, has experience with a wide range of programs bout within its own borders and with other countries. This paper briefly describes this experience and the lessons learned from Canada's involvement in the transfer of nuclear power technology. Nuclear technology is complex and diverse and yet it can be assimilated by a nation given a fire commitment of both suppliers and recipients of technology to achieve success. Canada has reaped large benefits from its nuclear program and we believe this has been instrumentally linked to the sharing of goals and opportunity for participation over extended periods of time by many interests within the Canadian infrastructure. While Canada has accumulated considerable expertise in nuclear technology transfer, we believe there is still much for US to learn. Achieving proficiency in any of the many kinds of nuclear related technologies will place a heavy burden on the financial and human resources of a nation. Care must be taken to plan carefully the total criteria which will assure national benefits in industrial and economic development. Above all, effective transfer of nuclear technology requires a long term commitment by both parties

  18. The Canadian nuclear fuel waste management program

    Rummery, T.E.; Rosinger, E.L.J.

    1984-12-01

    The Canadian Nuclear Fuel Waste Management Program is in the fourth year of a ten-year generic research and development phase. The objective of this phase of the program is to assess the basic safety and environmental aspects of the concept of isolating immobilized fuel waste by deep underground disposal in plutonic rock. The major scientific and engineering components of the program, namely immobilization studies, geoscience research, and environmental and safety assessment, are described. Program funding, scheduling and associated external review processes are briefly outlined

  19. Government intervention in the Canadian nuclear industry

    Doern, G.B.

    1980-01-01

    Several facets of government intervention in the Canadian nuclear industry are examined by reviewing the general historical evolution of intervention since the Second World War and by a more detailed analysis of three case studies. The case studies are the public sector - private sector content of the initial CANDU reactor program in the 1950's, the regulation of the health and safety of uranium miners in the late 1960's and early 1970's, and the Ontario Hydro decision in 1978 to enter into longer-term (40 year) contracts for uranium for its power reactors. (auth)

  20. Government intervention in the Canadian nuclear industry

    Doern, G B [Carleton Univ., Ottawa, Ontario (Canada). School of Public Administration

    1980-01-01

    Several facets of government intervention in the Canadian nuclear industry are examined by reviewing the general historical evolution of intervention since the Second World War and by a more detailed analysis of three case studies. The case studies are the public sector - private sector content of the initial CANDU reactor program in the 1950's, the regulation of the health and safety of uranium miners in the late 1960's and early 1970's, and the Ontario Hydro decision in 1978 to enter into longer-term (40 year) contracts for uranium for its power reactors.

  1. Dismantling of nuclear facilities

    Tallec, M.; Kus, J.P.

    2009-01-01

    Nuclear facilities have a long estimable lifetime but necessarily limited in time. At the end of their operation period, basic nuclear installations are the object of cleansing operations and transformations that will lead to their definitive decommissioning and then to their dismantling. Because each facility is somewhere unique, cleansing and dismantling require specific techniques. The dismantlement consists in the disassembly and disposing off of big equipments, in the elimination of radioactivity in all rooms of the facility, in the demolition of buildings and eventually in the reconversion of all or part of the facility. This article describes these different steps: 1 - dismantling strategy: main de-construction guidelines, expected final state; 2 - industries and sites: cleansing and dismantling at the CEA, EDF's sites under de-construction; 3 - de-construction: main steps, definitive shutdown, preparation of dismantling, electromechanical dismantling, cleansing/decommissioning, demolition, dismantling taken into account at the design stage, management of polluted soils; 4 - waste management: dismantlement wastes, national policy of radioactive waste management, management of dismantlement wastes; 5 - mastery of risks: risk analysis, conformability of risk management with reference documents, main risks encountered at de-construction works; 6 - regulatory procedures; 7 - international overview; 8 - conclusion. (J.S.)

  2. Proceedings of the Canadian Nuclear Association 35. annual conference

    Loewer, R.

    1995-01-01

    The proceedings of the thirty-fifth annual conference of the Canadian Nuclear Association contain 22 papers organized in the following sessions: update on the status of the Canadian nuclear industry, non-proliferation and related political issues, nuclear waste disposal perspectives, regulatory issues, trade development, new markets, economics of nuclear electricity, public acceptance or rejection. In addition one paper from a CNA/CNS special session on nuclear diffraction is included. The individual papers have been abstracted separately

  3. Conference summaries of the Canadian Nuclear Association 30. annual conference, and the Canadian Nuclear Society 11. annual conference

    1990-01-01

    This volume contains conference summaries for the 30. annual conference of the Canadian Nuclear Association, and the 11. annual conference of the Canadian Nuclear Society. Topics of discussion include: energy needs and challenges facing the Canadian nuclear industry; the environment and nuclear power; the problems of maintaining and developing industrial capacity; the challenges of the 1990's; programmes and issues for the 1990's; thermalhydraulics; reactor physics and fuel management; nuclear safety; small reactors; fuel behaviour; energy production and the environment; computer applications; nuclear systems; fusion; materials handling; and, reactor components

  4. Proceedings of the Canadian Nuclear Society 12. annual conference

    1991-01-01

    This volume contains the Proceedings of the seventeen Technical Sessions from the Twelfth Annual Conference of the Canadian Nuclear Society held in Saskatoon, Saskatchewan, June 9 to 12, 1991. As in previous years, the Annual Conference of the Canadian Nuclear Society was held in conjunction with the Annual Conference of the Canadian Nuclear Association. The major topics of discussion included: reactor physics; thermal hydraulics; industrial irradiation; computer applications; fuel channel analysis; small reactors; severe accidents; fuel behaviour under accident conditions; reactor components; safety related computer software; nuclear fuel management; nuclear waste management; and, uranium mining processing

  5. Proceedings of the Canadian Nuclear Society 15. annual conference

    Huynh, H.M.

    1994-01-01

    The proceedings of the 15. annual conference of the Canadian Nuclear Society cover a wide range of nuclear topics, but the emphasis is on CANDU reactors and Canadian experience. The 89 papers are arranged in 17 sessions dealing with the following subjects: thermalhydraulics, fuel channels, operations, reactor physics, fuel, new technology, safety, training, waste management. The individual papers have been abstracted separately

  6. Proceedings of the Canadian Nuclear Society 15. annual conference

    Huynh, H M [Hydro-Quebec, Montreal, PQ (Canada)

    1994-12-31

    The proceedings of the 15. annual conference of the Canadian Nuclear Society cover a wide range of nuclear topics, but the emphasis is on CANDU reactors and Canadian experience. The 89 papers are arranged in 17 sessions dealing with the following subjects: thermalhydraulics, fuel channels, operations, reactor physics, fuel, new technology, safety, training, waste management. The individual papers have been abstracted separately.

  7. Filters in nuclear facilities

    Berg, K.H.; Wilhelm, J.G.

    1985-01-01

    The topics of the nine papers given include the behavior of HEPA filters during exposure to air flows of high humidity as well as of high differential pressure, the development of steel-fiber filters suitable for extreme operating conditions, and the occurrence of various radioactive iodine species in the exhaust air from boiling water reactors. In an introductory presentation the German view of the performance requirements to be met by filters in nuclear facilities as well as the present status of filter quality assurance are discussed. (orig.) [de

  8. Decommissioning nuclear facilities

    Buck, S.

    1996-01-01

    Nuclear facilities present a number of problems at the end of their working lives. They require dismantling and removal but public and environmental protection remain a priority. The principles and strategies are outlined. Experience of decommissioning in France and the U.K. had touched every major stage of the fuel cycle by the early 1990's. Decommissioning projects attempt to restrict waste production and proliferation as waste treatment and disposal are costly. It is concluded that technical means exist to deal with present civil plant and costs are now predictable. Strategies for decommissioning and future financial provisions are important. (UK)

  9. Nuclear reactor facility

    Wampole, N.C.

    1978-01-01

    In order to improve the performance of manitenance and inspections it is proposed for a nuclear reactor facility with a primary circuit containing liquid metal to provide a thermally insulated chamber, within which are placed a number of components of the primary circuit, as e.g. valves, recirculation pump, heat exchangers. The isolated placement permit controlled preheating on one hand, but prevents undesirable heating of adjacent load-bearing elements on the other. The chamber is provided with heating devices and, on the outside, with cooling devices; it is of advantage to fill it with an inert gas. (UWI) 891 HP [de

  10. Status of the Canadian nuclear fuel waste management program

    Allan, C.J.; Stephens, M.E.

    1992-01-01

    The Canadian Concept for the permanent disposal of nuclear fuel waste has been developed extensively over the past several years, and is now well-advanced. The Concept, which involves the construction of a waste vault 500 to 1000 metres deep in plutonic rock located in the Canadian Precambrian Shield, is supported by an R ampersand D program with the following objectives: (1) to develop and demonstrate technology to site, design, build and operate a disposal facility; (2) to develop and demonstrate a methodology to evaluate the performance of the disposal system; and (3) to demonstrate that sites are likely to exist in the Canadian Precambrian Shield that would meet the regulatory requirements. A combination of engineered and natural barriers will be used to ensure that the vault design will meet rigorous safety standards. Experimental work is being carried out to elucidate all the important phenomena associated with the safety of the vault, including the performance of engineered barriers, natural geological barriers, and the biosphere

  11. MAPLE: a Canadian multipurpose reactor concept for national nuclear development

    Lidstone, R.F.

    1984-06-01

    Atomic Energy of Canada Limited, following an investigation of Canadian and international needs and world-market prospects for research reactors, has developed a new multipurpose concept, called MAPLE (Multipurpose Applied Physics Lattice Experimental). The MAPLE concept combines H 2 O- and D 2 O-moderated lattices within a D 2 O calandria tank in order to achieve the flux advantages of a basic H 2 O-cooled and moderated core along with the flexibility and space of a D 2 O-moderated core. The SUGAR (Slowpoke Uprated for General Applied Research) MAPLE version of the conept provides a range of utilization that is well suited to the needs of countries with nuclear programs at an early stage. The higher power MAPLE version furnishes high neutron flux levels and the variety of irradiation facilities that are appropriate for more advanced nuclear programs

  12. Geoscience research for the Canadian nuclear fuel waste management program

    Whitaker, S.H.

    1987-01-01

    The Canadian Nuclear Fuel Waste Management Program is assessing the concept of deep disposal of nuclear fuel waste in plutonic rock. As part of that assessment, a broad program of geoscience and geotechnical work has been undertaken to develop methods for characterizing sites, incorporating geotechnical data into disposal facility design, and incorporating geotechnical data into environmental and safety assessment of the disposal system. General field investigations are conducted throughout the Precambrian Shield, subsurface investigations are conducted at designated field research areas, and in situ rock mass experiments are being conducted in an Underground Research Laboratory. Samples from the field research areas and elsewhere are subjected to a wide range of tests and experiments in the laboratory to develop an understanding of the physical and chemical processes involved in ground-water-rock-waste interactions. Mathematical models to simulate these processes are developed, verified and validated. 114 refs.; 13 figs

  13. Canadians, nuclear weapons, and the Cold War security dilemma

    Eaton, M.A.

    2007-01-01

    This dissertation provides a history of Canadian ideas about nuclear weapons from the late 1950s until the end of the Trudeau era in 1984. Throughout this period, Canadians reacted to the insecurity they felt in the world around them by expressing many conflicting, often irreconcilable views about a range of nuclear weapon issues, including Canada's acquisition of nuclear warheads in 1963, the U.S. ABM program in the 1960s and early 1970s, the role of Canadian nuclear technology in the development of India's first nuclear explosion, and the Trudeau government's decision to allow the U.S. military to test cruise missiles in northern Canada The dissertation concludes with an examination of the emergence of a broadly-based, increasingly mainstream and influential anti-nuclear movement in the early 1980s, the clearest manifestation of the insecurity Canadians experienced at the time. .The nuclear debates examined in this dissertation reveal that Canadians were divided over nuclear weapons, nuclear strategy, the arms race, proliferation, and arms control and disarmament. In particular, they came to fundamentally different conclusions about how Canada's nuclear weapon policies, and its support for the nuclear policies of its alliances, would contribute to international stability and order. Some believed that their security rested on the maintenance of a strong Western nuclear deterrent and supported Canada contributing to its credibility; others believed that the constant modernisation of nuclear arsenals fuelled by the superpower arms race posed a serious threat to their security. This conceptual dilemma-the security through nuclear strength argument versus the fear that the quest for security through quantitative and qualitative improvements of nuclear stockpiles increased the likelihood of nuclear war-left Canadians divided over the value and utility of nuclear weapons and the strategies developed around them. At the same time, Canadians' ideas about nuclear weapons

  14. Steel structures for nuclear facilities

    1993-01-01

    In the guide the requirements concerning design and fabrication of steel structures for nuclear facilities and documents to be submitted to the Finnish Centre for Radiation and Nuclear Safety (STUK) are presented. Furthermore, regulations concerning inspection of steel structures during construction of nuclear facilities and during their operation are set forth

  15. An overview of the evaluations of nuclear power by Canadians

    Barrados, Maria

    1980-01-01

    Limited data are available on Canadian evaluations of nuclear power. General observations are made, based on a 1976 national study by B. Greer-Wootten and a 1978 Canadian Gallup Poll survey. Little change in the knowledge Canadians have of nuclear power appears to have taken place. A sizeable proportion of the population is willing to offer an opinion about the use of nuclear power while knowing nothing about it. Increased knowledge is not associated with more positive or negative evaluations of nuclear power. In more specific evaluations of nuclear safety, increased knowledge is found to be associated with a lowered confidence in the safety of Canadian reactors. There appears to have been a drop in the proportions of Canadians somewhat in favour of nuclear power between 1976 and 1978. Since many Canadians do not know much about the use of nuclear power and the majority of opinions are not strongly committed, there is considerable potential for fluctuation in these figures. Increased emphasis appears to be put on waste management issues in 1978, while nuclear power plants are less likely to be perceived as unsafe. This may be the result of increased discussion of Canadian power reactors. (LL)

  16. Proceedings of the Canadian Nuclear Association 25th annual conference

    1985-01-01

    The twenty addresses presented in this volume celebrate the 25th anniversary of the Canadian Nuclear Association. They reflect upon evolving world electricity patterns, the nuclear power option, Canada's position as a supplier of uranium and nuclear technology, the future of the nuclear industry in Canada, and the position of the industry in the United States and Britain

  17. Decommissioning of nuclear facilities

    Lunning, W.H.

    1977-01-01

    Collaborative studies are in progress in the U.K. between the U.K.A.E.A., the Generating Boards and other outside bodies, to identify the development issues and practical aspects of decommissioning redundant nuclear facilities. The various types of U.K.A.E.A. experimental reactors (D.F.R., W.A.G.R , S.G.H.W.R.) in support of the nuclear power development programme, together with the currently operating commercial 26 Magnox reactors in 11 stations, totalling some 5 GW will be retired before the end of the century and attention is focussed on these. The actual timing of withdrawal from service will be dictated by development programme requirements in the case of experimental reactors and by commercial and technical considerations in the case of electricity production reactors. Decommissioning studies have so far been confined to technical appraisals including the sequence logic of achieving specific objectives and are based on the generally accepted three stage progression. Stage 1, which is essentially a defuelling and coolant removal operation, is an interim phase. Stage 2 is a storage situation, the duration of which will be influenced by environmental pressures or economic factors including the re-use of existing sites. Stage 3, which implies removal of all active and non-active waste material and returning the site to general use, must be the ultimate objective. The engineering features and the radioactive inventory of the system must be assessed in detail to avoid personnel or environmental hazards during Stage 2. These factors will also influence decisions on the degree of Stage 2 decommissioning and its duration, bearing in mind that for Stage 3 activation may govern the waste disposal route and the associated radiation man-rem exposure during dismantling. Ideally, planning for decommissioning should be considered at the design stage of the facility. An objective of present studies is to identify features which would assist decommissioning of future systems

  18. Security culture for nuclear facilities

    Gupta, Deeksha; Bajramovic, Edita

    2017-01-01

    Natural radioactive elements are part of our environment and radioactivity is a natural phenomenon. There are numerous beneficial applications of radioactive elements (radioisotopes) and radiation, starting from power generation to usages in medical, industrial and agriculture applications. But the risk of radiation exposure is always attached to operational workers, the public and the environment. Hence, this risk has to be assessed and controlled. The main goal of safety and security measures is to protect human life, health, and the environment. Currently, nuclear security considerations became essential along with nuclear safety as nuclear facilities are facing rapidly increase in cybersecurity risks. Therefore, prevention and adequate protection of nuclear facilities from cyberattacks is the major task. Historically, nuclear safety is well defined by IAEA guidelines while nuclear security is just gradually being addressed by some new guidance, especially the IAEA Nuclear Security Series (NSS), IEC 62645 and some national regulations. At the overall level, IAEA NSS 7 describes nuclear security as deterrence and detection of, and response to, theft, sabotage, unauthorized access, illegal transfer or other malicious acts involving nuclear, other radioactive substances and their associated facilities. Nuclear security should be included throughout nuclear facilities. Proper implementation of a nuclear security culture leads to staff vigilance and a high level of security posture. Nuclear security also depends on policy makers, regulators, managers, individual employees and members of public. Therefore, proper education and security awareness are essential in keeping nuclear facilities safe and secure.

  19. Nuclear fuel storage facility

    Matsumoto, Takashi; Isaka, Shinji.

    1987-01-01

    Purpose: To increase the spent fuel storage capacity and reduce the installation cost in a nuclear fuel storage facility. Constitution: Fuels handled in the nuclear fuel storage device of the present invention include the following four types: (1) fresh fuels, (2) 100 % reactor core charged fuels, (3) spent fuels just after taking out and (4) fuels after a certain period (for example one half-year) from taking out of the reactor. Reactivity is high for the fuels (1), and some of fuels (2), while low in the fuels (3) (4), Source intensity is strong for the fuels (3) and some of the fuels (2), while it is low for the fuels (1) and (4). Taking notice of the fact that the reactivity, radioactive source intensity and generated after heat are different in the respective fuels, the size of the pool and the storage capacity are increased by the divided storage control. While on the other hand, since the division is made in one identical pool, the control method becomes important, and the working range is restricted by means of a template, interlock, etc., the operation mode of the handling machine is divided into four, etc. for preventing errors. (Kamimura, M.)

  20. A comparative analysis of managing radioactive waste in the Canadian nuclear and non-nuclear industries

    Batters, S.; Benovich, I.; Gerchikov, M. [AMEC NSS Ltd., Toronto, ON (Canada)

    2011-07-01

    Management of radioactive waste in nuclear industries in Canada is tightly regulated. The regulated nuclear industries include nuclear power generation, uranium mining and milling, nuclear medicine, radiation research and education and industrial users of nuclear material (e.g. radiography, thickness gauges, etc). In contrast, management of Naturally Occurring Radioactive Material (NORM) waste is not regulated by the Canadian Nuclear Safety Commission (CNSC), with the exception of transport above specified concentrations. Although these are radioactive materials that have always been present in various concentrations in the environment and in the tissues of every living animal, including humans, the hazards of similar quantities of NORM radionuclides are identical to those of the same or other radionuclides from regulated industries. The concentration of NORM in most natural substances is so low that the associated risk is generally regarded as negligible, however higher concentrations may arise as the result of industrial operations such as: oil and gas production, mineral extraction and processing (e.g. phosphate fertilizer production), metal recycling, thermal electric power generation, water treatment facilities. Health Canada has published the Canadian Guidelines for the Management of Naturally Occurring Radioactive Materials (NORM). This paper presents a comparative analysis of the requirements for management of radioactive waste in the regulated nuclear industries and of the guidelines for management of NORM waste. (author)

  1. A comparative analysis of managing radioactive waste in the Canadian nuclear and non-nuclear industries

    Batters, S.; Benovich, I.; Gerchikov, M.

    2011-01-01

    Management of radioactive waste in nuclear industries in Canada is tightly regulated. The regulated nuclear industries include nuclear power generation, uranium mining and milling, nuclear medicine, radiation research and education and industrial users of nuclear material (e.g. radiography, thickness gauges, etc). In contrast, management of Naturally Occurring Radioactive Material (NORM) waste is not regulated by the Canadian Nuclear Safety Commission (CNSC), with the exception of transport above specified concentrations. Although these are radioactive materials that have always been present in various concentrations in the environment and in the tissues of every living animal, including humans, the hazards of similar quantities of NORM radionuclides are identical to those of the same or other radionuclides from regulated industries. The concentration of NORM in most natural substances is so low that the associated risk is generally regarded as negligible, however higher concentrations may arise as the result of industrial operations such as: oil and gas production, mineral extraction and processing (e.g. phosphate fertilizer production), metal recycling, thermal electric power generation, water treatment facilities. Health Canada has published the Canadian Guidelines for the Management of Naturally Occurring Radioactive Materials (NORM). This paper presents a comparative analysis of the requirements for management of radioactive waste in the regulated nuclear industries and of the guidelines for management of NORM waste. (author)

  2. Ecknomic benefits arising from the Canadian nuclear industry

    1982-03-01

    This document is a collection of surveys of the Canadian nuclear industry, with forecasts covering a number of possible scenarios. Topics covered include uranium mining and processing; economic benefits arising from the design, manufacture and construction of CANDU generating stations; employment and economic activity in the Canadian nqclear industry; and an overview of the remainder of the industry

  3. Computerized system controls Canadian training facility

    Dingwall, K.

    1996-01-01

    The Petroleum Industry Training Service (PITS), a non-profit organization headquartered in Calgary, Alberta, Canada, has earned a reputation as the most sophisticated training organization of its kind. Backed by such resources as the $25-million Nisku Training Center, located on a 38-acre site near Edmonton, PITS provides present and future petroleum engineers/operators/administrators with on-the-job experience in every facet of oil/gas processing. Nearly 3,000 students attend the Nisku training facility each year. Courses range in length from one day to six months, on topics as diverse as petroleum engineering, field production, drilling and well service, safety, environmental impact and management. Designed to teach skills needed at all levels, the courses fulfill an important educational need for firms with both new hires and seasoned personnel. PITS certificates are well-recognized by industry and government agencies

  4. Concrete structures for nuclear facilities

    1996-01-01

    The detailed requirements for the design and fabrication of the concrete structures for nuclear facilities and for the documents to be submitted to the Finnish Centre for Radiation and Nuclear Safety (STUK) are given in the guide. It also sets the requirements for the inspection of concrete structures during the construction and operation of facilities. The requirements of the guide primarily apply to new construction. As regards the repair and modification of nuclear facilities built before its publication, the guide is followed to the extent appropriate. The regulatory activities of the Finnish Centre for Radiation and Nuclear Safety during a nuclear facility's licence application review and during the construction and operation of the facility are summarised in the guide YVL 1.1

  5. Childhood leukemia around nuclear facilities

    1991-01-01

    This Information Bulletin highlights the conclusion made from an Atomic Energy Control Board of Canada (AECB) study on the incidence of childhood leukemia near nuclear facilities. All of the locations with the nuclear facilities are located in Ontario, the nuclear generating stations at Pickering and Bruce; the uranium mines and mills in Elliot Lake; the uranium refining facility in Port Hope; and nuclear research facilities located at Chalk River plus the small nuclear power plant in Rolphton. Two conclusions are drawn from the study: 1) while the rate of childhood leukemias made be higher or lower than the provincial average, there is no statistical evidence that the difference is due to anything but the natural variation in the occurrence of the disease; and 2) the rate of occurrence of childhood leukemia around the Pickering nuclear power station was slightly greater than the Ontario average both before and after the plant opened, but this, too , could be due to the natural variation

  6. Proceedings of the Canadian Nuclear Society sixth annual conference

    French, P.M.; Phillips, G.J.

    1985-01-01

    The proceedings of the Sixth Annual Conference of the Canadian Nuclear Society comprise 103 papers on the following subjects: fuel technology, nuclear plant safety, instrumentation, public and regulatory matters, fusion, fuel behaviour under normal and accident conditions, nuclear plant design and operations, thermal hydraulics, reactor physics, accelerators, waste management, new reactor concepts

  7. Research and Production Corporation Radiy activities within Canadian nuclear market

    Bakhmach, I.; Siora, O.; Kharchenko, V.; Sklyar, V.; Andrashov, A.

    2011-01-01

    This paper presents key results of RPC Radiy activities within Canadian nuclear market. RPC Radiy (located in Kirovograd, Ukraine) is a vendor which designs and produces digital safety I and C platform as well as turnkey applications, based on the platform, for NPPs (safety systems). The main feature of the Radiy Platform is the application of Field Programmable Gates Arrays (FPGA) as programmable components for logic control operations. Since 2009 RPC Radiy started to explore the possibility to conduct the expansion to Canadian nuclear market. The activities performed by RPC Radiy related to this direction are resulted in several joint projects with Canadian companies. (author)

  8. Finally, nuclear engineering textbooks with a Canadian flavour!

    Bonin, H.W.

    2002-01-01

    The need for nuclear engineering textbooks more appropriate to the Canadian nuclear industry context and the CANDU nuclear reactor program has long been felt not only among the universities offering nuclear engineering programs at the graduate level, but also within the Canadian nuclear industry itself. Coverage of the CANDU reactor system in the textbooks presently supporting teaching is limited to a brief description of the concept. Course instructors usually complement these textbooks with course notes written from their personal experience from past employment within the nuclear industry and from their research interests In the last ten years, the Canadian nuclear industry has been involved on an increasing basis with the issue of the technology transfer to foreign countries which have purchased CANDU reactors or have been in the process of purchasing one or several CANDUs. For some of these countries, the 'turn key' approach is required, in which the Canadian nuclear industry looks after everything up to the commissioning of the nuclear power plant, including the education and training of local nuclear engineers and plant personnel. Atomic Energy of Canada Limited (AECL) in particular has dispatched some personnel tasked to prepare and give short courses on some specific aspects of CANDU design and operation, but a lack of consistency was observed as different persons prepared and gave the courses rather independently. To address the many problems tied with nuclear engineering education, the CANTEACH program was set up involving major partners of the Canadian nuclear industry. Parts of the activities foreseen by CANTEACH consist in the writing of nuclear engineering textbooks and associated computer-based pedagogical material. The present paper discusses the main parts of two textbooks being produced, one in reactor physics at steady state and the other on nuclear fuel management. (author)

  9. Women and nuclear issues: Comments in a Canadian perspective

    Dionne-Marsolais, Rita

    1989-01-01

    When the Canadian Nuclear industry launched its information program, it was found that women were less supportive of nuclear power. Reasons were difficult to pin-point and hovered around individual perceptions and misunderstandings. The basis of the Canadian Nuclear Association Public Information program lies with its target: men and women equally. The Program Takes Into Consideration The major characteristics and nuances of these two groups. Female Characteristics from Canadian Perspective are: Strong sense of generation continuity; Detail and task oriented; Nontechnical training; Strong sense of individuality (local). Patterns of behavoiur in relation to nuclear industry for women in Canada are: not prone to take risks; micro-economic approach to decisions (local); little confidence in technology; pragmatic and balanced in their choices (local). Major concerns of Canadian women are: Safety of power plants; disposal of waste; peace and environment versus growth and energy need; trustworthiness of the industry. Canadian nuclear association public information program communirations -approach covers: the right message, down to earth language, factual and real information for real choices, effective reach: spokespeople and media buy. Results of polls: show thtt women are less in favour of Nuclear energy in Canada today than men, consider NPPs less important in Meeting Canada's energy need in the years ahead; and think that Nuclear Energy is not a choice for Canada of all sources of energy available for large scale use

  10. Canadians, nuclear weapons, and the Cold War security dilemma

    Eaton, M.A

    2007-07-01

    This dissertation provides a history of Canadian ideas about nuclear weapons from the late 1950s until the end of the Trudeau era in 1984. Throughout this period, Canadians reacted to the insecurity they felt in the world around them by expressing many conflicting, often irreconcilable views about a range of nuclear weapon issues, including Canada's acquisition of nuclear warheads in 1963, the U.S. ABM program in the 1960s and early 1970s, the role of Canadian nuclear technology in the development of India's first nuclear explosion, and the Trudeau government's decision to allow the U.S. military to test cruise missiles in northern Canada The dissertation concludes with an examination of the emergence of a broadly-based, increasingly mainstream and influential anti-nuclear movement in the early 1980s, the clearest manifestation of the insecurity Canadians experienced at the time. .The nuclear debates examined in this dissertation reveal that Canadians were divided over nuclear weapons, nuclear strategy, the arms race, proliferation, and arms control and disarmament. In particular, they came to fundamentally different conclusions about how Canada's nuclear weapon policies, and its support for the nuclear policies of its alliances, would contribute to international stability and order. Some believed that their security rested on the maintenance of a strong Western nuclear deterrent and supported Canada contributing to its credibility; others believed that the constant modernisation of nuclear arsenals fuelled by the superpower arms race posed a serious threat to their security. This conceptual dilemma-the security through nuclear strength argument versus the fear that the quest for security through quantitative and qualitative improvements of nuclear stockpiles increased the likelihood of nuclear war-left Canadians divided over the value and utility of nuclear weapons and the strategies developed around them. At the same time, Canadians

  11. Guidelines for Management Information Systems in Canadian Health Care Facilities

    Thompson, Larry E.

    1987-01-01

    The MIS Guidelines are a comprehensive set of standards for health care facilities for the recording of staffing, financial, workload, patient care and other management information. The Guidelines enable health care facilities to develop management information systems which identify resources, costs and products to more effectively forecast and control costs and utilize resources to their maximum potential as well as provide improved comparability of operations. The MIS Guidelines were produced by the Management Information Systems (MIS) Project, a cooperative effort of the federal and provincial governments, provincial hospital/health associations, under the authority of the Canadian Federal/Provincial Advisory Committee on Institutional and Medical Services. The Guidelines are currently being implemented on a “test” basis in ten health care facilities across Canada and portions integrated in government reporting as finalized.

  12. Earthquake engineering for nuclear facilities

    Kuno, Michiya

    2017-01-01

    This book is a comprehensive compilation of earthquake- and tsunami-related technologies and knowledge for the design and construction of nuclear facilities. As such, it covers a wide range of fields including civil engineering, architecture, geotechnical engineering, mechanical engineering, and nuclear engineering, for the development of new technologies providing greater resistance against earthquakes and tsunamis. It is crucial both for students of nuclear energy courses and for young engineers in nuclear power generation industries to understand the basics and principles of earthquake- and tsunami-resistant design of nuclear facilities. In Part I, "Seismic Design of Nuclear Power Plants", the design of nuclear power plants to withstand earthquakes and tsunamis is explained, focusing on buildings, equipment's, and civil engineering structures. In Part II, "Basics of Earthquake Engineering", fundamental knowledge of earthquakes and tsunamis as well as the dynamic response of structures and foundation ground...

  13. Childhood leukemia around five nuclear facilities in Canada

    Elaguppillai, V.

    1992-05-01

    As a result of public concern over the incidence of leukemia around the Sellafield nuclear fuel reprocessing plant, the Canadian Atomic Energy Control Board commissioned a study to test for similar clustering around licensed nuclear facilities in Ontario. In this study the incidence and mortality of leukemia among children up to the age of 14 years born within a radius of about 25 km from five different types of facilities were compared to the provincial average. The facilities considered were the Pickering Nuclear Generating Station, the Bruce Nuclear Power Development, the uranium conversion facility at Port Hope, the uranium mine and mill facilities in Elliot Lake, and the Chalk River Laboratories. The ratio of observed to expected childhood leukemias was around unity at the 95 percent confidence level, indicating that the occurrence of the disease is not significantly different from the provincial average. The sample size is not large enough to distinguish between a change occurrence and a true excess or deficit. (table)

  14. Environmental monitoring of nuclear facilities

    Winter, M.

    1983-01-01

    The objectives of one environmental monitoring program for nuclear facilities, are presented. The program in Federal Republic of Germany, its goals, its basic conditions, its regulations, and its dose limits are emphasized. (E.G.) [pt

  15. Proceedings of the Canadian Nuclear Association 34. annual conference

    Girard, A.M.

    1994-01-01

    The proceedings of the thirty-fourth annual conference of the Canadian Nuclear Association contain 23 complete papers and three speeches organized in the following sessions: opening, plenary, new environmental regulations and their effect on the energy industry, CANDU update, life cycle management of nuclear power plants, evolution of nuclear technology, technologies for tomorrow, nuclear used fuel and disposal of low-level waste, world economics and energy consumption. The complete papers have been abstracted separately

  16. World-wide cooperation in nuclear power: a canadian perspective

    Whelan, D.

    2000-01-01

    This paper presents the point of view of Canadian Authorities about the future of nuclear activities. Generally speaking, OECD countries will be focusing their efforts on plant refurbishment, maintenance and life extension while non-OECD countries will be facing capacity expansion needs. This duality will favour collaboration in the nuclear field between OECD and other countries. Key areas for enhanced cooperation will be: nuclear technology, nuclear safety, regulations, waste management, non-proliferation and financing

  17. Proceedings of the Canadian Nuclear Association 34. annual conference

    Girard, A M [Atomic Energy of Canada Ltd., Montreal, PQ (Canada). CANDU Operations

    1994-12-31

    The proceedings of the thirty-fourth annual conference of the Canadian Nuclear Association contain 23 complete papers and three speeches organized in the following sessions: opening, plenary, new environmental regulations and their effect on the energy industry, CANDU update, life cycle management of nuclear power plants, evolution of nuclear technology, technologies for tomorrow, nuclear used fuel and disposal of low-level waste, world economics and energy consumption. The complete papers have been abstracted separately.

  18. Waste management in Canadian nuclear programs

    Dyne, P.J.

    The objectives of the Canadian radioactive waste management program are described. Recycling actinides through reactors is being studied. Low and medium level waste treatments such as reverse osmosis concentration, immobilization in bitumen and plastics, and incineration are under study. Spent fuel can be stored dry in concrete canisters above ground and ultimate storage of wastes in salt deposits or hard rock is appropriate to Canadian conditions. (E.C.B.)

  19. Nuclear facilities licensing

    Carvalho, A.J.M. de.

    1978-01-01

    The need for the adoption of a legal and normative system, defining objectives, pescriptions and the process of nuclear licensing and building of nuclear power plants in Brazil is enphasized. General rules for the development of this system are presented. The Brazilian rules on the matter are discussed. A general view of the German legal system for nuclear power plant licensing and the IAEA recommendations on the subject are finally presented. (A.L.S.L.) [pt

  20. Proceedings of the seventeenth annual Canadian Nuclear Society conference

    1996-01-01

    The seventeenth annual conference of the Canadian Nuclear Society, presented in Fredericton, New Brunswick. The conference includes papers on general topics of interest on the nuclear community, waste management and the environment, instrumentation and design of Candu reactors, safety analysis, thermal hydraulics, fuel channels, plant operations and in-core instrumentation

  1. Proceedings of the seventeenth annual Canadian Nuclear Society conference

    NONE

    1997-12-31

    The seventeenth annual conference of the Canadian Nuclear Society, presented in Fredericton, New Brunswick. The conference includes papers on general topics of interest on the nuclear community, waste management and the environment, instrumentation and design of Candu reactors, safety analysis, thermal hydraulics, fuel channels, plant operations and in-core instrumentation.

  2. The Canadian Nuclear Safety Commission's financial guarantee requirements

    Ferch, R.

    2006-01-01

    The Nuclear Safety and Control Act gives the Canadian Nuclear Safety Commission (CNSC) the legal authority to require licensees to provide financial guarantees in order to meet the purposes of the Act. CNSC policy and guidance with regard to financial guarantees is outlined, and the current status of financial guarantee requirements as applied to various CNSC licensees is described. (author)

  3. Fatigue damage of nuclear facilities

    2001-01-01

    The conference on the fatigue damage of nuclear facilities, organized by the SFEN (french society of nuclear energy), took place at Paris the 23. of november 2000. Eleven papers were presented, showing the state of the art and the research programs in the domain of the sizing rules, safety, installations damage, examination and maintenance. (A.L.B.)

  4. Decontamination of nuclear facilities

    1982-01-01

    Thirty-seven papers were presented at this conference in five sessions. Topics covered include regulation, control and consequences of decontamination; decontamination of components and facilities; chemical and non-chemical methods of decontamination; and TMI decontamination experience

  5. Facilities inventory protection for nuclear facilities

    Schmitt, F.J.

    1989-01-01

    The fact that shut-down applications have been filed for nuclear power plants, suggests to have a scrutinizing look at the scopes of assessment and decision available to administrations and courts for the protection of facilities inventories relative to legal and constitutional requirements. The paper outlines the legal bases which need to be observed if purposeful calculation is to be ensured. Based on the different actual conditions and legal consequences, the author distinguishes between 1) the legal situation of facilities licenced already and 2) the legal situation of facilities under planning during the licencing stage. As indicated by the contents and restrictions of the pertinent provisions of the Atomic Energy Act and by the corresponding compensatory regulation, the object of the protection of facilities inventor in the legal position of the facility owner within the purview of the Atomic Energy Act, and the licensing proper. Art. 17 of the Atomic Energy Act indicates the legislators intent that, once issued, the licence will be the pivotal point for regulations aiming at protection and intervention. (orig./HSCH) [de

  6. Socket welds in nuclear facilities

    Anderson, P.A.; Torres, L.L.

    1995-01-01

    Socket welds are easier and faster to make than are butt welds. However, they are often not used in nuclear facilities because the crevices between the pipes and the socket sleeves may be subject to crevice corrosion. If socket welds can be qualified for wider use in facilities that process nuclear materials, the radiation exposures to welders can be significantly reduced. The current tests at the Idaho Chemical Processing Plant (ICPP) are designed to determine if socket welds can be qualified for use in the waste processing system at a nuclear fuel processing plant

  7. The decommissioning of nuclear facilities

    Niel, J.Ch.; Rieu, J.; Lareynie, O.; Delrive, L.; Vallet, J.; Girard, A.; Duthe, M.; Lecomte, C.; Rozain, J.P.; Nokhamzon, J.G.; Davoust, M.; Eyraud, J.L.; Bernet, Ph.; Velon, M.; Gay, A.; Charles, Th.; Leschaeva, M.; Dutzer, M.; Maocec, Ch.; Gillet, G.; Brut, F.; Dieulot, M.; Thuillier, D.; Tournebize, F.; Fontaine, V.; Goursaud, V.; Birot, M.; Le Bourdonnec, Th.; Batandjieva, B.; Theis, St.; Walker, St.; Rosett, M.; Cameron, C.; Boyd, A.; Aguilar, M.; Brownell, H.; Manson, P.; Walthery, R.; Wan Laer, W.; Lewandowski, P.; Dorms, B.; Reusen, N.; Bardelay, J.; Damette, G.; Francois, P.; Eimer, M.; Tadjeddine, A.; Sene, M.; Sene, R.

    2008-01-01

    This file includes five parts: the first part is devoted to the strategies of the different operators and includes the following files: the decommissioning of nuclear facilities Asn point of view, decommissioning of secret nuclear facilities, decommissioning at the civil Cea strategy and programs, EDF de-construction strategy, Areva strategy for decommissioning of nuclear facilities; the second one concerns the stakes of dismantling and includes the articles as follow: complete cleanup of buildings structures in nuclear facilities, decommissioning of nuclear facilities and safety assessment, decommissioning wastes management issues, securing the financing of long-term decommissioning and waste management costs, organizational and human factors in decommissioning projects, training for the decommissioning professions: the example of the Grenoble University master degree; the third part is devoted to the management of dismantling work sites and includes the different articles as follow: decommissioning progress at S.I.C.N. plant, example of decommissioning work site in Cea Grenoble: Siloette reactor decommissioning, matters related to decommissioning sites, decommissioning of french nuclear installations: the viewpoint of a specialist company, specificities of inspections during decommissioning: the Asn inspector point of view; the fourth part is in relation with the international approach and includes as follow: IAEA role in establishing a global safety regime on decommissioning, towards harmonization of nuclear safety practices in Europe: W.E.N.R.A. and the decommissioning of nuclear facilities, EPA superfund program policy for decontamination and decommissioning, progress with remediation at Sellafield, progress and experiences from the decommissioning of the Eurochemic reprocessing plant in Belgium, activities of I.R.S.N. and its daughter company Risk-audit I.r.s.n./G.r.s. international in the field of decommissioning of nuclear facilities in eastern countries

  8. Lessons learned from recent safety related incidents at A Canadian uranium conversion facility

    Jaferi, Jafir

    2013-01-01

    This paper presents the Canadian Nuclear Safety Commission's (CNSC) regulatory requirements for nuclear fuel facility licensees to report any situation or incident that results or is likely to result in a hazard to the health or safety of any person or the environment and to submit its incident investigation report with cause(s) of the incident and corrective actions taken or planned. In addition, the paper presents two recent safety-related incidents that occurred at a uranium conversion facility in Canada along with their consequences, causes, corrective actions and any lessons learned. The first incident resulted in a release of uranium hexafluoride (UF6) inside the UF6 cylinder filling station and the second one resulted in a spill of uranium tetrafluoride (UF 4 ) slurry inside the UF6 plant. Both incidents had no impact on the workers or the environment. (authors)

  9. Safeguards and security aspects of a potential Canadian used-fuel disposal facility

    Smith, R.M.; Wuschke, D.; Baumgartner, P.

    1994-09-01

    Large quantities of highly radioactive used fuel have been produced by Canadian nuclear generating stations. Conceptual design and development is under way to assess a means of disposing of this used fuel within a vault located 500 to 1000 m deep in plutonic rock in the Canadian Shield. In parallel with this work, the safeguards and physical security measures that will be required for this used fuel during transportation, packaging, and containment in a disposal vault are being studied in Canada, in several other countries that have similar requirements and by the International Atomic Energy Agency. Canadian commitments and regulations applicable to used-fuel transportation and disposal are described. The experience gained from applying safeguards and physical security measures at similar facilities is considered together with the availability of equipment that might be used in applying these measures. Possible safeguards and physical security measures are outlined and considered. These measures are based on the conceptual design studies for a reference Used-Fuel Disposal Centre and associated transportation systems undertaken by Atomic Energy of Canada Limited and Ontario Hydro. These studies show that effective and practical safeguards, which meet present IAEA objectives, can be applied to the used fuel in transportation and at a disposal facility. They also show that physical security measures can be employed that have a high probability of preventing theft or sabotage. 27 refs., 8 figs., 3 tabs., glossary, 2 appendices

  10. Safeguards and security aspects of a potential Canadian used-fuel disposal facility

    Smith, R M; Wuschke, D; Baumgartner, P

    1994-09-01

    Large quantities of highly radioactive used fuel have been produced by Canadian nuclear generating stations. Conceptual design and development is under way to assess a means of disposing of this used fuel within a vault located 500 to 1000 m deep in plutonic rock in the Canadian Shield. In parallel with this work, the safeguards and physical security measures that will be required for this used fuel during transportation, packaging, and containment in a disposal vault are being studied in Canada, in several other countries that have similar requirements and by the International Atomic Energy Agency. Canadian commitments and regulations applicable to used-fuel transportation and disposal are described. The experience gained from applying safeguards and physical security measures at similar facilities is considered together with the availability of equipment that might be used in applying these measures. Possible safeguards and physical security measures are outlined and considered. These measures are based on the conceptual design studies for a reference Used-Fuel Disposal Centre and associated transportation systems undertaken by Atomic Energy of Canada Limited and Ontario Hydro. These studies show that effective and practical safeguards, which meet present IAEA objectives, can be applied to the used fuel in transportation and at a disposal facility. They also show that physical security measures can be employed that have a high probability of preventing theft or sabotage. 27 refs., 8 figs., 3 tabs., glossary, 2 appendices.

  11. Ventilation of nuclear facilities

    1982-01-01

    In this work an examination is made of ventilation problems in nuclear installations, of the fuel cycle or the handling of radioactive compounds. The study covers the detection of radioactive aerosols, purification, iodine trapping, ventilation equipment and its maintenance, engineering, safety of ventilation, fire efficiency, operation, regulations and normalization [fr

  12. Proceedings of the 29th annual conference of the Canadian Nuclear Association and 10th annual conference of the Canadian Nuclear Society. V. 1-3

    Harvey, M.; Fehrenbach, P.J.

    1989-01-01

    The symposium was designed to highlight how the technical information for nuclear energy came to Canada, the effect this information had in Canada in the fields of Physics, Chemistry, Medicine and Nuclear Power. Volume 1 is the combined proceedings of the Canadian Nuclear Association twenty-ninth annual conference and the Canadian Nuclear Society tenth annual conference. Volume 2 is the proceedings of the Canadian Nuclear Association twenty-ninth annual conference, and volume 3 is the proceedings of the Canadian Nuclear Society tenth annual conference

  13. Proceedings of the 29th annual conference of the Canadian Nuclear Association and 10th annual conference of the Canadian Nuclear Society. V. 1-3

    Harvey, M; Fehrenbach, P J [eds.

    1990-12-31

    The symposium was designed to highlight how the technical information for nuclear energy came to Canada, the effect this information had in Canada in the fields of Physics, Chemistry, Medicine and Nuclear Power. Volume 1 is the combined proceedings of the Canadian Nuclear Association twenty-ninth annual conference and the Canadian Nuclear Society tenth annual conference. Volume 2 is the proceedings of the Canadian Nuclear Association twenty-ninth annual conference, and volume 3 is the proceedings of the Canadian Nuclear Society tenth annual conference.

  14. LAMPF: a nuclear research facility

    Livingston, M.S.

    1977-09-01

    A description is given of the recently completed Los Alamos Meson Physics Facility (LAMPF) which is now taking its place as one of the major installations in this country for the support of research in nuclear science and its applications. Descriptions are given of the organization of the Laboratory, the Users Group, experimental facilities for research and for applications, and procedures for carrying on research studies

  15. Nuclear Station Facilities Improvement Planning

    Hooks, R. W.; Lunardini, A. L.; Zaben, O.

    1991-01-01

    An effective facilities improvement program will include a plan for the temporary relocation of personnel during the construction of an adjoining service building addition. Since the smooth continuation of plant operation is of paramount importance, the phasing plan is established to minimize the disruptions in day-to-day station operation and administration. This plan should consider the final occupancy arrangements and the transition to the new structure; for example, computer hookup and phase-in should be considered. The nuclear industry is placing more emphasis on safety and reliability of nuclear power plants. In order to do this, more emphasis is placed on operations and maintenance. This results in increased size of managerial, technical and maintenance staffs. This in turn requires improved office and service facilities. The facilities that require improvement may include training areas, rad waste processing and storage facilities, and maintenance facilities. This paper discusses an approach for developing an effective program to plan and implement these projects. These improvement projects can range in magnitude from modifying a simple system to building a new structure to allocating space for a future project. This paper addresses the planning required for the new structures with emphasis on site location, space allocation, and internal layout. Since facility planning has recently been completed by Sargent and Leyden at six U. S. nuclear stations, specific examples from some of those plants are presented. Site planning and the establishment of long-range goals are of the utmost importance when undertaking a facilities improvement program for a nuclear station. A plan that considers the total site usage will enhance the value of both the new and existing facilities. Proper planning at the beginning of the program can minimize costs and maximize the benefits of the program

  16. Disaster countermeasures around nuclear facilities

    Tatsuta, Yoshinori

    1982-01-01

    The following matters are described. Safety regulation administration for nuclear power plants; nuclear disaster countermeasures in the United States; disaster countermeasures around nuclear facilities (a report of the ad hoc committee in Nuclear Safety Commission), including general requirements, the scope of areas to take the countermeasures, emergency environmental monitoring, guidelines for taking the countermeasures, and emergency medical treatment. In the nuclear safety administration, the system of stationing safety expert personnel on the sites of nuclear power generation and qualifying the persons in charge of reactor operation in the control room is also introduced. As for the disaster countermeasures, such as the detection of an abnormal state, the notification of the abnormality to various organs concerned, the starting of emergency environmental monitoring, the establishment of the countermeasure headquarters, and emergency measures for the local people. (Mori, K.)

  17. Nuclear issues in the Canadian energy context

    1979-01-01

    Participants holding a wide spectrum of views and representing the nuclear industry, churches, anti-nuclear groups, and the general public participated in sessions on the ethics of nuclear power, waste disposal, health and environmental effects of energy development, decision making and the regulatory process, and the economics of nuclear and other energy sources.

  18. On things nuclear: the Canadian debate

    Mueller, P.G.

    1977-01-01

    An unbiased overview is given of the nuclear industry in Canada, with emphasis on its history, fundamentals of nuclear power plants and the CANDU reactor system, the need and ideal mix of future energy sources, economics of nuclear power, uranium supplies, radioactive releases, thermal pollution, physical security, and safety of nuclear power plants, and export of CANDU technology vs. nuclear proliferation. (E.C.B.)

  19. Technology transfer. Its contribution to the Canadian nuclear industry

    Perryman, E.C.W.

    1977-01-01

    Technology transfer from the Laboratories of Atomic Energy of Canada Limited is discussed in relation to the birth and growth of the Canadian Nuclear Industry. The evolution of the laboratories and their changing emphasis during the commercialization of the CANDU reactor system is described

  20. Nuclear worries of Canadian youth: Replication and extension

    Lewis, C.; Goldberg, S.; Parker, K.R.

    1989-01-01

    A national survey of Canadian adolescents assessed concern, anxiety, and sources of information about the threat of nuclear war. Results indicated few geographical or gender differences in overall levels of concern, although females were more likely to admit fear and anxiety, and students with activist parents showed more concern. Family ranked below all media as a source of information

  1. Introduction to nuclear facilities engineering

    Sapy, Georges

    2012-06-01

    Engineering, or 'engineer's art', aims at transforming simple principle schemes into operational facilities often complex especially when they concern the nuclear industry. This transformation requires various knowledge and skills: in nuclear sciences and technologies (nuclear physics, neutronics, thermal-hydraulics, material properties, radiation protection..), as well as in non-nuclear sciences and technologies (civil engineering, mechanics, electricity, computer sciences, instrumentation and control..), and in the regulatory, legal, contractual and financial domains. This book explains how this huge body of knowledge and skills must be organized and coordinated to create a reliable, exploitable, available, profitable and long-lasting facility, together with respecting extremely high safety, quality, and environmental impact requirements. Each aspect of the problem is approached through the commented presentation of nuclear engineering macro-processes: legal procedures and administrative authorizations, nuclear safety/radiation protection/security approach, design and detailed studies, purchase of equipments, on-site construction, bringing into operation, financing, legal, contractual and logistic aspects, all under the global control of a project management. The 'hyper-complexness' of such an approach leads to hard points and unexpected events. The author identifies the most common ones and proposes some possible solutions to avoid, mitigate or deal with them. In a more general way, he proposes some thoughts about the performance factors of a nuclear engineering process

  2. Meteorological instrumentation for nuclear facilities

    Costa, A.C.L. da.

    1983-01-01

    The main requirements of regulatory agencies, concerning the meteorological instrumentation needed for the licensing of nuclear facilities are discussed. A description is made of the operational principles of sensors for the various meteorological parameters and associated electronic systems. An analysis of the problems associated with grounding of a typical meteorological station is presented. (Author) [pt

  3. Nuclear reactor containing facility

    Hidaka, Masataka; Murase, Michio.

    1994-01-01

    In a reactor containing facility, a condensation means is disposed above the water level of a cooling water pool to condensate steams of the cooling water pool, and return the condensated water to the cooling water pool. Upon occurrence of a pipeline rupture accident, steams generated by after-heat of a reactor core are caused to flow into a bent tube, blown from the exit of the bent tube into a suppression pool and condensated in a suppression pool water, thereby suppressing the pressure in the reactor container. Cooling water in the cooling water pool is boiled by heat conduction due to the condensation of steams, then the steams are exhausted to the outside of the reactor container to remove the heat of the reactor container to the outside of the reactor. In addition, since cooling water is supplied to the cooling water pool quasi-permanently by gravity as a natural force, the reactor container can be cooled by the cooling water pool for a long period of time. Since the condensation means is constituted with a closed loop and interrupted from the outside, radioactive materials are never released to the outside. (N.H.)

  4. Nuclear power generation facility

    Kubo, Mitsuji.

    1996-01-01

    Main steams are introduced from a moisture separation device for removing moisture content of the main steams to a low pressure turbine passing through a cross-around pipe. A condensate desalter comprising a mixed floor-type desalting tower using granular ion exchange resins is disposed at the downstream of the main condensator by way of condensate pipelines, and a feedwater heater is disposed at the downstream. Structural members of the main condensator are formed by weather proof steels. Low alloy steels are used partially or entirely for the cross-around pipe, gas extraction pipelines, heat draining pipelines, inner structural members other than pipelines in the feedwater heater, and the body and the inner structural members of the moisture separator. Titanium or a titanium alloy is used for the pipelines in the main condensator. With such a constitution, BWR type reactor facilities, in which the concentration of cruds inflown to the condensate cleanup system is reduced to simplify the condensate cleanup device can be obtained. (I.N.)

  5. Design requirements for new nuclear reactor facilities in Canada

    Shim, S.; Ohn, M.; Harwood, C.

    2012-01-01

    The Canadian Nuclear Safety Commission (CNSC) has been establishing the regulatory framework for the efficient and effective licensing of new nuclear reactor facilities. This regulatory framework includes the documentation of the requirements for the design and safety analysis of new nuclear reactor facilities, regardless of size. For this purpose, the CNSC has published the design and safety analysis requirements in the following two sets of regulatory documents: 1. RD-337, Design of New Nuclear Power Plants and RD-310, Safety Analysis for Nuclear Power Plants; and 2. RD-367, Design of Small Reactor Facilities and RD-308, Deterministic Safety Analysis for Small Reactor Facilities. These regulatory documents have been modernized to document past practices and experience and to be consistent with national and international standards. These regulatory documents provide the requirements for the design and safety analysis at a high level presented in a hierarchical structure. These documents were developed in a technology neutral approach so that they can be applicable for a wide variety of water cooled reactor facilities. This paper highlights two particular aspects of these regulatory documents: The use of a graded approach to make the documents applicable for a wide variety of nuclear reactor facilities including nuclear power plants (NPPs) and small reactor facilities; and, Design requirements that are new and different from past Canadian practices. Finally, this paper presents some of the proposed changes in RD-337 to implement specific details of the recommendations of the CNSC Fukushima Task Force Report. Major changes were not needed as the 2008 version of RD-337 already contained requirements to address most of the lessons learned from the Fukushima event of March 2011. (author)

  6. The nuclear industry and the NPT: a Canadian view

    MacOwen, W.

    1987-01-01

    The effect of Canada's safeguards policy on Canadian industry and on the conduct of Canada's international nuclear trade is examined. When India exploded a nuclear device in 1974 Canada terminated all nuclear collaboration with India and also insisted that other countries renegotiated existing contracts to include more stringent safeguards. This damaged Canada's trading reputation and its position will have to be rebuilt. It is suggested that international agreement on some practicable and comprehensive rules for international trade in nuclear items should be pursued. (U.K.)

  7. Radiation protection in nuclear facilities

    Piechowski, J.; Lochard, J.; Lefaure, Ch.; Schieber, C.; Schneider, Th; Lecomte, J.F.; Delmont, D.; Boitel, S.; Le Fauconnier, J.P.; Sugier, A; Zerbib, J.C.; Barbey, P.

    1998-01-01

    Close ties exist between nuclear safety and radiation protection. Nuclear safety is made up of all the arrangements taken to prevent accidents occurring in nuclear facilities, these accidents would certainly involved a radiological aspect. Radiation protection is made up of all the arrangements taken to evaluate and reduce the impact of radiation on workers or population in normal situations or in case of accident. In the fifties the management of radiological hazards was based on the quest for minimal or even zero risk. This formulation could lead to call some activities in question whereas the benefits for the whole society were evident. Now a new attitude more aware of the real risks and of no wasting resources prevails. This attitude is based on the ALARA principle whose purpose is to maintain the exposure to radiation as low as reasonably achievable taking into account social and economic concerns. This document regroups articles illustrating different aspects of the radiation protection in nuclear facilities such as a research center, a waste vitrification workshop and a nuclear power plant. The surveillance of radiological impacts of nuclear sites on environment is examined, a point is made about the pending epidemiologic studies concerning La Hague complex. (A.C.)

  8. Severe accident considerations in Canadian nuclear power reactors

    Omar, A.M.; Measures, M.P.; Scott, C.K.; Lewis, M.J.

    1990-08-01

    This paper describes a current study on severe accidents being sponsored by the Atomic Energy Control Board (AECB) and provides background on other related Canadian work. Scoping calculations are performed in Phase I of the AECB study to establish the relative consequences of several permutations resulting from six postulated initiating events, nine containment states, and a selection of meteorological conditions and health effects mitigating criteria. In Phase II of the study, selected accidents sequences would be analyzed in detail using models suitable for the design features of the Canadian nuclear power reactors

  9. Nuclear materials facility safety initiative

    Peddicord, K.L.; Nelson, P.; Roundhill, M.; Jardine, L.J.; Lazarev, L.; Moshkov, M.; Khromov, V.V.; Kruchkov, E.; Bolyatko, V.; Kazanskij, Yu.; Vorobeva, I.; Lash, T.R.; Newton, D.; Harris, B.

    2000-01-01

    Safety in any facility in the nuclear fuel cycle is a fundamental goal. However, it is recognized that, for example, should an accident occur in either the U.S. or Russia, the results could seriously delay joint activities to store and disposition weapons fissile materials in both countries. To address this, plans are underway jointly to develop a nuclear materials facility safety initiative. The focus of the initiative would be to share expertise which would lead in improvements in safety and safe practices in the nuclear fuel cycle.The program has two components. The first is a lab-to-lab initiative. The second involves university-to-university collaboration.The lab-to-lab and university-to-university programs will contribute to increased safety in facilities dealing with nuclear materials and related processes. These programs will support important bilateral initiatives, develop the next generation of scientists and engineers which will deal with these challenges, and foster the development of a safety culture

  10. Physical security of nuclear facilities

    Dixon, H.

    1987-01-01

    A serious problem with present security systems at nuclear facilities is that the threats and standards prepared by the NRC and DOE are general, and the field offices are required to develop their own local threats and, on that basis, to prepared detailed specifications for security systems at sites in their jurisdiction. As a result, the capabilities of the systems vary across facilities. Five steps in particular are strongly recommended as corrective measures: 1. Those agencies responsible for civil nuclear facilities should jointly prepare detailed threat definitions, operational requirements, and equipment specifications to protect generic nuclear facilities, and these matters should be issued as policy. The agencies should provide sufficient detail to guide the design of specific security systems and to identify candidate components. 2. The DOE, NRC, and DOD should explain to Congress why government-developed security and other military equipment are not used to upgrade existing security systems and to stock future ones. 3. Each DOE and NRC facility should be assessed to determine the impact on the size of the guard force and on warning time when personnel-detecting radars and ground point sensors are installed. 4. All security guards and technicians should be investigated for the highest security clearance, with reinvestigations every four years. 5. The processes and vehicles used in intrafacility transport of nuclear materials should be evaluated against a range of threats and attack scenarios, including violent air and vehicle assaults. All of these recommendations are feasible and cost-effective. The appropriate congressional subcommittees should direct that they be implemented as soon as possible

  11. Laundry monitor for nuclear facilities

    Ishibashi, Mitsuo (Toshiba Corp., Fuchu (Japan). Fuchu Works)

    1984-06-01

    A laundry monitor has been developed for the detection and cleansification of radiation contamination on the clothes, headgear, footgear, etc. of workers in nuclear facilities. With this monitor, measurement is made irrespective of the size and shape of the objects; a large-area plastic scintillation detector is incorporated; it has stable and highly sensitive characteristics, with the merits of swift measurement, economical operation and easy maintenance. Connected with a folding machine, automatic carrying and storing compartment through a conveyor, it is capable of saving energy and man power, contributing to scheduled operation, and improving the efficiency of the facilities.

  12. Laundry monitor for nuclear facilities

    Ishibashi, Mitsuo

    1984-01-01

    A laundry monitor has been developed for the detection and cleansification of radiation contamination on the clothes, headgear, footgear, etc. of workers in nuclear facilities. With this monitor, measurement is made irrespective of the size and shape of the objects ; a large-area plastic scintillation detector is incorporated ; it has stable and highly sensitive characteristics, with the merits of swift measurement, economical operation and easy maintenance. Connected with a folding machine, automatic carrying and storing compartment through a conveyor, it is capable of saving energy and man power, contributing to scheduled operation, and improving the efficiency of the facilities. (author)

  13. Particulate filtration in nuclear facilities

    1991-01-01

    The removal of particulate radioactive material from exhaust air or gases is an essential feature of virtually all nuclear facilities. Recent IAEA publications have covered the broad designs of off-gas and air cleaning systems for the range of nuclear power plants and other facilities. This report is a complementary guidebook that examines in detail the latest developments in the design, operation, maintenance and testing of fibrous air filters. The original draft of the report was prepared by three consultants, M.W. First, of the School of Public Health, Harvard University, United States of America, K.S. Robinson, from the UKAEA Harwell Laboratory, United Kingdom, and H.G. Dillmann, of the Kernforschungzentrum, Karlsruhe, Germany. The Technical Committee Meeting (TCM), at which the report was reviewed and much additional information contributed, was attended by 11 experts and was held in Vienna, from 30 May to 3 June 1988. 64 refs, 41 figs, 10 tabs

  14. Technology transfer from Canadian nuclear laboratories

    MacDonald, R.D.; Evans, W.; MacEwan, J.R.; Melvin, J.G.

    1985-09-01

    Canada has developed a unique nuclear power system, the CANDU reactor. AECL - Research Company (AECL-RC) has played a key role in the CANDU program by supplying its technology to the reactor's designers, constructors and operators. This technology was transferred from our laboratories to our sister AECL companies and to domestic industries and utilities. As CANDUs were built overseas, AECL-RC made its technology available to foreign utilities and agencies. Recently the company has embarked on a new transfer program, commercial R and D for nuclear and non-nuclear customers. During the years of CANDU development, AECL-RC has acquired the skills and technology that are especially valuable to other countries embarking on their own nuclear programs. This report describes AECL-RC's thirty years' experience with the transfer of technology

  15. PROJECTIZING AN OPERATING NUCLEAR FACILITY

    Adams, N

    2007-01-01

    This paper will discuss the evolution of an operations-based organization to a project-based organization to facilitate successful deactivation of a major nuclear facility. It will describe the plan used for scope definition, staff reorganization, method estimation, baseline schedule development, project management training, and results of this transformation. It is a story of leadership and teamwork, pride and success. Workers at the Savannah River Site's (SRS) F Canyon Complex (FCC) started with a challenge--take all the hazardous byproducts from nearly 50 years of operations in a major, first-of-its-kind nuclear complex and safely get rid of them, leaving the facility cold, dark, dry and ready for whatever end state is ultimately determined by the United States Department of Energy (DOE). And do it in four years, with a constantly changing workforce and steadily declining funding. The goal was to reduce the overall operating staff by 93% and budget by 94%. The facilities, F Canyon and its adjoined sister, FB Line, are located at SRS, a 310-square-mile nuclear reservation near Aiken, S.C., owned by DOE and managed by Washington Group International subsidiary Washington Savannah River Company (WSRC). These facilities were supported by more than 50 surrounding buildings, whose purpose was to provide support services during operations. The radiological, chemical and industrial hazards inventory in the old buildings was significant. The historical mission at F Canyon was to extract plutonium-239 and uranium-238 from irradiated spent nuclear fuel through chemical processing. FB Line's mission included conversion of plutonium solutions into metal, characterization, stabilization and packaging, and storage of both metal and oxide forms. The plutonium metal was sent to another DOE site for use in weapons. Deactivation in F Canyon began when chemical separations activities were completed in 2002, and a cross-functional project team concept was implemented to successfully

  16. Environmental monitoring of nuclear facilities

    Koelzer, W.

    1988-01-01

    Environmental monitoring of nuclear facilities is part of general monitoring for environmental radioactivity all over the territory of the Federal Republic of Germany. General principles of environmental monitoring were formulated by the ICRP in 1965. In 1974 guidelines for measures of monitoring the environment of NPP incorporating LWR were drafted, which helped to standardize environmental monitoring programs. Since 1958, data on environmental radioactivity from measurements by authorized laboratories have been published in reports. (DG)

  17. Decommissioning of nuclear power facilities

    Nosovskij, A.V.; Vasil'chenko, V.N.; Klyuchnikov, A.A.; Yashchenko, Ya.V.

    2005-01-01

    This is the first manual in Ukraine giving the complete review of the decommissioning process of the nuclear power facilities including the issues of the planning, design documentation development, advanced technology description. On the base of the international and domestic experience, the issues on the radwaste management, the decontamination methods, the equipment dismantling, the remote technology application, and also the costs estimate at decommissioning are considered. The special attention to the personnel safety provision, population and environment at decommissioning process is paid

  18. Canadian nuclear power plant construction cost forecast and analysis

    Keng, C.W.K.

    1985-01-01

    Because of the huge volume of capital required to construct a modern electric power generating station, investment decisions have to be made with as complete an understanding of the consequence of the decision as possible. This understanding must be provided by the evaluation of the situation to take place in the future. This paper attempts to use an econometric method to forecast the construction costs escalation of a standard Canadian nuclear generating station (NGS). A review of the history of Canadian nuclear electric power is provided. The major components of the construction costs of a Canadian NGS are studied and summarized. A data base is built and indexes are prepared. Based on these indexes an econometric forecasting model is constructed using an apparently new econometric methodology of forecasting modelling. Forecasts for a period of forty years are generated and applications of alternative scenario forecasts and range forecasts to uncertainty assessment are demonstrated. The indexes, the model, and the forecasts and their applications, to the best of the author's knowledge, are the very first ever done for Canadian NGS constructions

  19. Nuclear industry prospects: A Canadian perspective

    Morden, Reid

    1995-01-01

    Canada, with its proven, safe and versatile CANDU reactor is well poised for the second half-century of nuclear fission. Canada's nuclear pedigree goes back to the turn-of-the-century work of Ernest Rutherford in Montreal. This year, Canada's nuclear industry celebrates the 50th anniversary of the start-up of its first research reactor at Chalk River. Last year, the pioneering work of Bert ram Blockhouse in Physics was honoured with a Nobel Prize. Future international success for the nuclear industry, such as has been achieved here in Korea, depends on continued cooperative and collaborative team work between the public and private sectors, continued strong research and development backing by the government, and new strategic partnerships. The biggest challenge is financing for the emerging markets. The brightness or dimness of future prospects are relative to the intensity of the lessons learned from history. In Canada we have a fairly long nuclear pedigree, It goes back almost a century to 1898, when Ernest Rutherford set up a world centre at McGill University in Montreal for research into the structure of the atom and into radioactivity

  20. Computer Security at Nuclear Facilities

    Cavina, A.

    2013-01-01

    This series of slides presents the IAEA policy concerning the development of recommendations and guidelines for computer security at nuclear facilities. A document of the Nuclear Security Series dedicated to this issue is on the final stage prior to publication. This document is the the first existing IAEA document specifically addressing computer security. This document was necessary for 3 mains reasons: first not all national infrastructures have recognized and standardized computer security, secondly existing international guidance is not industry specific and fails to capture some of the key issues, and thirdly the presence of more or less connected digital systems is increasing in the design of nuclear power plants. The security of computer system must be based on a graded approach: the assignment of computer system to different levels and zones should be based on their relevance to safety and security and the risk assessment process should be allowed to feed back into and influence the graded approach

  1. Childhood leukemia around nuclear facilities

    Hatch, M.

    1992-01-01

    Epidemiologic studies on health effects of living near nuclear facilities have been rare and, indeed, radiobiological models would not predict any detectable increase in cancer risk to the general public from very low levels of radioactivity emitted by nuclear installations. Thus recent evidence suggesting an excess of childhood leukemias in the vicinity of certain nuclear sites in the United Kingdom has generated considerable controversy. To help resolve the uncertainty and enhance interpretability of results, future epidemiologic studies will need to be designed with great care (and within realistic cost limits). This commentary suggests three areas for methodologic consideration: 1. definition and modelling of radiation exposure; 2. selection of cancer sites and sensitive subgroups, and 3. use of incidence of mortality data. Specific suggestions for further epidemiologic research are offered as well. (author). 8 refs

  2. Research and development for Canadian nuclear power

    Robertson, J.A.

    1976-01-01

    Rapid expansion of the successful CANDU reactor system offers immediate substitution for scarce oil and gas, combined with long-term security of energy supplies. A continuing large and vigorous R and D program on nuclear power is essential to achieve these objectives. The program, described here, consists of tactical R and D in support of the current CANDU reactor system, strategic R and D to develop and demonstrate advanced CANDU systems, and exploratory R and D to put Canada in a position to exploit any fusion opportunities. Two support activities, management of radioactive wastes and techniques to safeguard nuclear materials against diversion, although integral components of the nuclear power programs, are identified separately because they are currently of special public interest. (author)

  3. Regulation of the Canadian nuclear industry

    Gummer, W.K.

    1982-02-01

    This paper reviews the nuclear regulatory process in Canada in the following context. First, the pertinent factors in the present political and economic environment are identified, including both domestic and international matters. Second, the basis for current Atomic Energy Control Board operations is considered, with reference to both the Atomic Energy Control Act (1946) and the proposed Nuclear Control and Administration Act (Bill C-14, 1977). Some specific areas of the regulatory process are discussed in detail to show where ambiguity or uncertainty may arise: these areas are uranium exploration and mining, occupational health and safety, environmental protection, waste management, heavy water plants and transportation

  4. Developing new products from Canadian nuclear technology

    Hatcher, S.R.; Lyon, R.B.

    1987-06-01

    By 1990, the Federal Government will have reduced its support for Atomic Energy of Canada Limited's nuclear R and D from the 1985 level of $200 million, to $100 million (1985 dollars). To meet the need for a broadened funding base, AECL Research Company has been restructured to become more responsive to our sponsors and customers. Although supporting the CANDU nuclear power program remains by far our largest R and D activity, we have put in place a comprehensive process for generating new business and commercial activities. Examples of such business opportunities are presented in the paper

  5. Lessons learned in planning the Canadian Nuclear Legacy Liabilities Program

    Stephens, M.; Brooks, S.; Miller, J.; Neal, P.; Mason, R.

    2011-01-01

    In 2006, Atomic Energy of Canada Limited (AECL) and Natural Resources Canada (NRCan) began implementing a $7B CDN, 70-year Nuclear Legacy Liabilities Program (NLLP) to deal with legacy decommissioning and environmental issues at AECL nuclear sites. The objective of the NLLP is to safely and cost-effectively reduce the nuclear legacy liabilities and associated risks based on sound waste management and environmental principles in the best interest of Canadians. The NLLP comprises a number of interlinked decommissioning, waste management and environmental restoration activities that are being executed at different sites by various technical groups. Many lessons about planning and executing such a large, diverse Program have been learned in planning the initial five-year 'start-up' phase (concluded 2011 March), in planning the three-year second phase (currently being commenced), and in planning individual and interacting activities within the Program. The activities to be undertaken in the start-up phase were planned by a small group of AECL technical experts using the currently available information on the liabilities. Several internal and external reviews of the Program during the start-up phase examined progress and identified several improvements to planning. These improvements included strengthening communications among the groups within the Program, conducting more detailed advance planning of the interlinked activities, and being cautious about making detailed commitments for activities for which major decisions had yet to be made. The second phase was planned by a dedicated core team. More and earlier input was solicited from the suppliers than in the planning for the first phase. This was to ensure that the proposed program of work was feasible, and to be able to specify in more detail the resources that would be required to carry it out. The NLLP has developed several processes to assist in the detailed planning of the numerous projects and

  6. Canadian Nuclear Association brief to the standing committee on Energy, Mines and Resources

    NONE

    1991-10-01

    The Canadian Nuclear Association outlines points on electricity demand, environmental impact of electricity production, Canada`s nuclear technology and uranium deposits. Several recommendations are discussed that promote the Canadian nuclear industry and outline issues related to greenhouse gas emmisions, nuclear waste containment, funding of R and D and outlines the need for improving the environmental assessment approval processes.

  7. Canadian Nuclear Association brief to the standing committee on Energy, Mines and Resources

    1991-10-01

    The Canadian Nuclear Association outlines points on electricity demand, environmental impact of electricity production, Canada's nuclear technology and uranium deposits. Several recommendations are discussed that promote the Canadian nuclear industry and outline issues related to greenhouse gas emmisions, nuclear waste containment, funding of R and D and outlines the need for improving the environmental assessment approval processes

  8. Status of the Canadian Nuclear Fuel Waste Management Program

    Lyon, R.B.

    1985-10-01

    The Canadian Nuclear Fuel Waste Management Program is in the fifth year of a ten-year generic research and development phase. The major objective of this phase of the program is to assess the basic safety and environmental aspects of the concept of isolating immobilized fuel waste by deep underground disposal in plutonic rock. The major scientific and engineering components of the program, namely immobilization studies, geoscience research, and environmental and safety assessment, are well established

  9. Organizing the Canadian nuclear industry to meet the challenge

    Lortie, Pierre.

    1983-06-01

    The CANDU reactor is struggling for a share of the dwindling reactor market against formidable and well-established competition. The Canadian nuclear industry has historically depended upon two crown corporations, Atomic Energy of Canada Ltd. and Ontario Hydro, which have taken the lead in designing and engineering the reactor. Crown corporations are not notably successful in marketing, however, and the time has come for the industry to organize itself in preparation for an aggressive export drive

  10. State of the art of nuclear facilities with organic cooled reactors

    Brede, O.

    1984-01-01

    USA, Canadian, and USSR activities aimed at developing nuclear facilities with organic cooled reactors are summarized. The facilities OMRE, PNPF, WR-1, and ARBUS are described, discussing in particular the problems of the chemistry of organic coolants. Finally, problems of further development and prospects of the application of organic cooled reactors are briefly outlined. (author)

  11. Terrorist threats of nuclear facilities

    Jozsef Solymosi; Jozser Ronaky; Zoltan Levai; Arpad Vincze; Laszlo Foldi

    2004-01-01

    More than one year has passed since the terrible terrorist attacks against the United States. The tragic event fundamentally restructured our security policy approach and made requirements of countering terrorism a top priority of the 21st century. In one year a lot of studies were published and the majority of them analyses primarily the beginnings of terrorism then focus on the interrelations of causes and consequences of the attacks against the WTC. In most of the cases the authors can only put their questions most of which have remained unanswered to date. Meanwhile, in a short while after the attacks the secret assessments of threat levels of potential targets and areas were also prepared. One of the high priority fields is the issue of nuclear, biological, and chemical security, in short NBC-security. Here and now we focus on component N, that is the assessment techniques of nuclear security in short, without aiming at completeness. Our definite objective is to make non-expert readers understand - and present a concrete example as it is done in risk analysis - the real danger-level of nuclear facilities and especially the terrorist threat. Our objective is not to give tips to terrorists but to provide them with deterring arguments and at the same time calm worried people. In our communique we give an overview of international practice of nuclear antiterrorism and of preventive nuclear protection in Hungary. (author)

  12. The Canadian nuclear fuel waste management program

    Dixon, R.S.; Rosinger, E.L.J.

    1984-04-01

    This report, the fifth of a series of annual reports, reviews the progress that has been made in the research and development program for the safe management and disposal of Canada's nuclear fuel waste. The report summarizes activities over the past year in the following areas: public interaction; used fuel storage and transportation; immobilization of used fuel and fuel recycle waste; geoscience research related to deep underground disposal; environmental research; and environmental and safety assessment

  13. The Sylvia Fedoruk Canadian Centre for Nuclear Innovation: advancing knowledge through partnerships

    Alexander, N.; Root, J.H., E-mail: neil.alexander@usask.ca, E-mail: john.root@usask.ca [Sylvia Fedoruk Canadian Centre for Nuclear Innovation, Saskatoon, SK (Canada); Chad, K., E-mail: karen.chad@usask.ca [Univ. of Saskatchewan, Saskatoon, SK (Canada); Bereznai, G., E-mail: george.bereznai@uoit.ca [Univ. of Ontario Inst. of Tech., Faculty of Energy Systems and Nuclear Science, Oshawa, ON (Canada); Dalzell, M.T.J., E-mail: matthew.dalzell@usask.ca [Sylvia Fedoruk Canadian Centre for Nuclear Innovation, Saskatoon, SK (Canada)

    2014-07-01

    The vision of the Sylvia Fedoruk Canadian Centre for Nuclear Innovation is to place the Canadian province of Saskatchewan among global leaders in nuclear research, development and training through partnerships with industry and academia for economic and social benefit. Saskatchewan is one of the world's largest producers of uranium and home to pioneering research in nuclear medicine, most notably the development of cobalt-60 teletherapy. The Fedoruk Centre is striving to build on this legacy through the attainment of four strategic goals: (1) building nuclear expertise and capacity through the support to academic programs and research projects in partnership with industry, academic institutions and research organizations in nuclear medicine, materials research, energy and the environment; (2) enhancing innovation in partnership with the research community and industry; (3) engaging communities and increasing understanding of risks, benefits and potential impacts of nuclear technologies; and (4) ensuring the sustainability and accountability of the Centre and its resources. The Fedoruk Centre's mandate includes the stewardship of select nuclear facilities, the first being a 24 MeV cyclotron and nuclear substances laboratory as a resource for the development of novel imaging agents, training and production of radioisotopes for clinical diagnoses. By attracting new research leadership in the nuclear domain, developing networks of expertise, training highly-qualified personnel in nuclear disciplines, stimulating industrial partnerships, and creating conditions for fact-based conversation regarding nuclear issues, the Fedoruk Centre is working to establish a research and innovation capacity to support a vibrant nuclear sector in Saskatchewan. (author)

  14. The Sylvia Fedoruk Canadian Centre for Nuclear Innovation: advancing knowledge through partnerships

    Alexander, N.; Root, J.H.; Chad, K.; Bereznai, G.; Dalzell, M.T.J.

    2014-01-01

    The vision of the Sylvia Fedoruk Canadian Centre for Nuclear Innovation is to place the Canadian province of Saskatchewan among global leaders in nuclear research, development and training through partnerships with industry and academia for economic and social benefit. Saskatchewan is one of the world's largest producers of uranium and home to pioneering research in nuclear medicine, most notably the development of cobalt-60 teletherapy. The Fedoruk Centre is striving to build on this legacy through the attainment of four strategic goals: (1) building nuclear expertise and capacity through the support to academic programs and research projects in partnership with industry, academic institutions and research organizations in nuclear medicine, materials research, energy and the environment; (2) enhancing innovation in partnership with the research community and industry; (3) engaging communities and increasing understanding of risks, benefits and potential impacts of nuclear technologies; and (4) ensuring the sustainability and accountability of the Centre and its resources. The Fedoruk Centre's mandate includes the stewardship of select nuclear facilities, the first being a 24 MeV cyclotron and nuclear substances laboratory as a resource for the development of novel imaging agents, training and production of radioisotopes for clinical diagnoses. By attracting new research leadership in the nuclear domain, developing networks of expertise, training highly-qualified personnel in nuclear disciplines, stimulating industrial partnerships, and creating conditions for fact-based conversation regarding nuclear issues, the Fedoruk Centre is working to establish a research and innovation capacity to support a vibrant nuclear sector in Saskatchewan. (author)

  15. Canadian nuclear desalination/cogeneration technology development

    Humphries, J.R.

    1996-01-01

    The goal of the CANDESAL program has been to develop innovative applications of existing technologies that would offer an energy efficient, cost effective mechanism for the production of potable water and electricity. Large scale seawater desalination will be an important element in the solution of the global water shortage problem. For nuclear desalination to capture a significant share of this growing market, it must be economically competitive, as well as offer other advantages over more traditional fossil-fueled alternatives. The focus of activities in Canada has been on development of the technology in directions that would result in improved water production efficiency, reduced energy consumption, reduced environmental burden and reduced costs

  16. Environmental monitoring of nuclear facilities

    Papadopoulos, D.; Winter, M.

    1982-01-01

    Environmental monitoring adds to the control of emissions of radioactive substances from nuclear facilities. The radioactive substances released with the exhaust air and the liquid effluent result in impact levels in the immediate vicinity, which must be ascertained by measurement. Impact control serves for the quantitative assessment of man-made radioactivity in different media of relevant pathways and for the direct assessment of the radiation exposure of the public living in the vicinity. In this way, the radiation exposure of the environment, which can be calculated if the emission data and the meteorological diffusion parameters are known, is controlled directly. (orig./RW)

  17. Success in nuclear technology transfer: A Canadian perspective

    Lawson, D.S.; Stevens, J.E.S.; Boulton, J.

    1986-10-01

    Technology transfer has played a significant part in the expansion of nuclear power to many countries of the world. Canada's involvement in nuclear technology transfer spans four decades. The experience gained through technology transfer, initially to Canadian industry and then to other countries in association with the construction of CANDU nuclear power plants, forms a basis from which to assess the factors which contribute to successful technology transfer. A strong commitment from all parties, in terms of both financial and human resources, is essential to success. Detailed planning of both the scope and timing of the technology transfer program is also required together with an assessment of the impact of the introduction of nuclear power on other sectors of the economy. (author)

  18. Nuclear fuel treatment facility for 'Mutsu'

    Kanazawa, Toshio; Fujimura, Kazuo; Horiguchi, Eiji; Kobayashi, Tetsuji; Tamekiyo, Yoshizou

    1989-01-01

    A new fixed mooring harbor in Sekinehama and surrounding land facilities to accommodate a test voyage for the nuclear-powered ship 'Mutsu' in 1990 were constructed by the Japan Atomic Energy Research Institute. Kobe Steel took part in the construction of the nuclear fuel treatment process in various facilities, beginning in October, 1988. This report describes the outline of the facility. (author)

  19. Fuel isolation research for the Canadian nuclear fuel waste management program

    1982-06-01

    This document is intended to give a broad outline of the Fuel Isolatikn program and to indicate how this program fits into the overall framework of the Canadian Nuclear Fuel Waste Management Program. Similar activities in other countries are described, and the differences in philosophy behind these and the Canadian program are highlighted. A program plan is presented that outlines the development of research programs that contribute to the safety assessment of the disposal concept and the development of technology required for selection and optimization of a feasible fuel isolation system. Some indication of the work that might take place beyond concept assessment, at the end of the decade, is also given. The current program is described in some detail, with emphasis on what the prkgram has achieved to date and hopes to achieve in the future for the concept assessment phase of the waste management program. Finally, some major capital facilities associated with the fuel isolation program are described

  20. Canadian public and leadership attitudes to nuclear power

    Dobson, J.K.

    1976-01-01

    Surveys of the Canadian public and leadership were carried out to determine levels of knowledge, perceptions and attitudes toward the use of nuclear power in Canada. The public sample included population over 18 years broken down by region, age, sex and education. The leadership study sampled businessmen, politicians, civil servants, academics and environmentalists. Only 56 % of the public indicated a knowledge of the use of nuclear power: 68 % were in favour, and of these, 39 % were unsure of its safety. Environmentalits were the most knowledgealbe of all the leadership groups, with academics second, and the remaining groups having low levels of information. Fear-producing aspects defined by the survey should be used as the basis for providing information. All leadership groups except environmentalists favoured nuclear power development. Leadership groups identified the same disadvantages as the public (radiation, waste management, pollution and explosions) but added cost. (J.T.A.)

  1. The Thai-Canadian nuclear human resources development linkage project

    Sumitra, Tatchai; Chankow, Nares; Bradley, K.; Bereznai, G.

    1998-01-01

    The Thai-Canadian Nuclear Human Resources Development Linkage Project (the P roject ) was initiated in 1994 in order to develop the engineering and scientific expertise needed for Thailand to decide whether and how the country can best benefit from the establishment of a nuclear power program. The Project was designed to upgrade current academics and people in industry, and to develop an adequate supply of new technical personnel for academic, industry, utility, regulatory and other government institutions. The key Project objectives included the establishment of a Chair in Nuclear Engineering at Chulalongkorn University, the upgrading of the current Masters level curriculum, the establishment of undergraduate and doctorate level curricula, development and delivery of an industrial training program for people in industry and government, exchanges of Thai and Canadian academics and industry experts to establish common research programs and teaching interests, and a public education program that was to test in Thailand some of the techniques that have been successfully used in Canada. (author)

  2. Application of robotics in nuclear facilities

    Byrd, J.S.; Fisher, J.J.

    1986-01-01

    Industrial robots and other robotic systems have been successfully applied at the Savannah River nuclear site. These applications, new robotic systems presently under development, general techniques for the employment of robots in nuclear facilities, and future systems are discussed

  3. Tritium transport around nuclear facilities

    Murphy, C.E. Jr.; Sweet, C.W.

    1981-01-01

    The transport and cycling of tritium around nuclear facilities is reviewed with special emphasis on studies at the Savannah River Laboratory, Aiken, South Carolina. These studies have shown that the rate of deposition from the atmosphere, the site of deposition, and the subsequent cycling are strongly influenced by the compound with which the tritium is associated. Tritiated hydrogen is largely deposited in the soil, while tritiated water is deposited in the greatest quantity in the vegetation. Tritiated hydrogen is converted in the soil to tritiated water that leaves the soil slowly, through drainage and transpiration. Tritiated water deposited directly to the vegetation leaves the vegetation more rapidly after exposure. Only a small part of the tritium entering the vegetation becomes bound in organic molecules. However, it appears tht the existence of soil organic compounds with tritium concentrations greater than the equilibrium concentration in the associated water can be explained by direct metabolism of tritiated hydrogen in vegetation

  4. Neutron skyshine from nuclear facilities

    Nakamura, Takashi; Hayashi, Katsumi.

    1984-01-01

    The advance in neutron skyshine research and the significance are first described. Then, skyshine calculation methods in 1980s particularly and the skyshine experiment in Japan with various nuclear facilities (reactors, D-T neutron sources, accelerators) are reviewed. In comparison with such experiment usable as bench mark, the skyshine calculation methods (Monte Carlo method, transport calculation method) are evaluated for their accuracy and merits and demerits. The values by Monte Carlo calculation were in agreement within about 30 % with the experimental values. Those by DOT 3.5 calculation were twice as large as the experimental values. Those by PALLAS calculation were in good agreement in dose with the experimental values, but the spectra were considerably different. The values by SKYSHINE-2 were in good agreement with the experimental values, but since the ground effect was ignored, the values may deviate from the experimental ones if it is taken into account. (Mori, K.)

  5. Lessons learned in planning the Canadian Nuclear Legacy Liabilities Program

    Stephens, Michael E.; Brooks, Sheila M.; Miller, Joan M.; Mason, Robert A.

    2011-01-01

    In 2006, Atomic Energy of Canada Limited (AECL) and Natural Resources Canada (NRCan) began implementing a $7B CDN, 70-year Nuclear Legacy Liabilities Program (NLLP) to deal with legacy decommissioning and environmental issues at AECL nuclear sites. The objective of the NLLP is to safely and cost-effectively reduce the nuclear legacy liabilities and associated risks based on sound waste management and environmental principles in the best interest of Canadians. The liabilities include shutdown research and prototype power reactors, fuel handling facilities, radiochemical laboratories, support buildings, radioactive waste storage facilities, and contaminated lands at several sites located across eastern Canada from Quebec to Manitoba. The largest site, Chalk River Laboratories (CRL) in Ontario, will continue as an operational nuclear site for the foreseeable future. Planning and delivery of the Program is managed by the Liability Management Unit (LMU), a group that was formed within AECL for the purpose. The composition and progress of the NLLP has been reported in recent conferences. The NLLP comprises a number of interlinked decommissioning, waste management and environmental restoration activities that are being executed at different sites, and by various technical groups as suppliers to the LMU. Many lessons about planning and executing such a large, diverse Program have been learned in planning the initial five-year 'start-up' phase (which will conclude 2011 March), in planning the five-year second phase (which is currently being finalized), and in planning individual and interacting activities within the Program. The activities to be undertaken in the start-up phase were planned by a small group of AECL technical experts using the currently available information on the liabilities. Progress in executing the Program was slower than anticipated due to less than ideal alignment between some planned technical solutions and the actual requirements, as well as the

  6. Nonreactor nuclear facilities: standards and criteria guide

    Brynda, W.J.; Junker, L.; Karol, R.C.; Lobner, P.R.; Goldman, L.A.

    1981-09-01

    This guide is a source document that identifies standards, codes, and guides that address the nuclear safety considerations pertinent to nuclear facilities as defined in DOE Order 5480.1, Chapter V, Safety of Nuclear Facilities. The guidance and criteria provided are directed toward areas of safety usually addressed in a Safety Analysis Report. The areas of safety include, but are not limited to, siting, principal design criteria and safety system design guidelines, radiation protection, accident analysis, and quality assurance. The guide is divided into two sections: general guidelines and appendices. Those guidelines that are broadly applicable to most nuclear facilities are presented in the general guidelines. These general guidelines may have limited applicability to subsurface facilities such as waste repositories. Guidelines specific to the various types or categories of nuclear facilities are presented in the appendices. These facility-specific appendices provide guidelines and identify standards and criteria that should be considered in addition to, or in lieu of, the general guidelines

  7. Safety analysis of the proposed Canadian geologic nuclear waste repository

    Prowse, D.R.

    1977-01-01

    The Canadian program for development and qualification of a geologic repository for emplacement of high-level and long-lived, alpha-emitting waste from irradiated nuclear fuel has been inititiated and is in its initial development stage. Fieldwork programs to locate candidate sites with suitable geological characteristics have begun. Laboratory studies and development of models for use in safety analysis of the emplaced nuclear waste have been initiated. The immediate objective is to complete a simplified safety analysis of a model geologic repository by mid-1978. This analysis will be progressively updated and will form part of an environmental Assessment Report of a Model Fuel Center which will be issued in mid-1979. The long-term objectives are to develop advanced safety assessment models of a geologic repository which will be available by 1980

  8. Nonreactor nuclear facilities: Standards and criteria guide

    Brynda, W.J.; Scarlett, C.H.; Tanguay, G.E.; Lobner, P.R.

    1986-09-01

    This guide is a source document that identifies standards, codes, and guides that address the nuclear safety considerations pertinent to nuclear facilities as defined in DOE 5480.1A, Chapter V, ''Safety of Nuclear Facilities.'' The guidance and criteria provided is directed toward areas of safety usually addressed in a Safety Analysis Report. The areas of safety include, but are not limited to, siting, principal design criteria and safety system design guidelines, radiation protection, accident analysis, conduct of operations, and quality assurance. The guide is divided into two sections: general guidelines and appendices. Those guidelines that are broadly applicable to most nuclear facilities are presented in the general guidelines. Guidelines specific to the various types or categories of nuclear facilities are presented in the appendices. These facility-specific appendices provide guidelines and identify standards and criteria that should be considered in addition to, or in lieu of, the general guidelines. 25 figs., 62 tabs

  9. Base isolation for nuclear power and nuclear material facilities

    Eidinger, J.M.; Kircher, C.A.; Vaidya, N.; Constantinou, M.; Kelly, J.M.; Seidensticker, R.; Tajirian, F.F.; Ovadia, D.

    1989-01-01

    This report serves to document the status of the practice for the use of base isolation systems in the design and construction of nuclear power and nuclear material facilities. The report first describes past and current (1989) applications of base isolation in nuclear facilities. The report then provides a brief discussion of non-nuclear applications. Finally, the report summarizes the status of known base-isolation codes and standards

  10. Policy on the decommissioning of nuclear facilities

    1988-08-01

    This Regulatory Policy Statement describes the policy of the Atomic Energy Control Board (AECB) on the decommissioning of those facilities defined as nuclear facilities in the Atomic Energy Control (AEC) Regulations. It is intended as a formal statement, primarily for the information of licensees, or potential licensees, of the regulatory process and requirements generally applicable to the decommissioning of nuclear facilities licensed and regulated by the AECB pursuant to the authority of the AEC Act and Regulations

  11. Estimating Fire Risks at Industrial Nuclear Facilities

    Coutts, D.A.

    1999-01-01

    The Savannah River Site (SRS) has a wide variety of nuclear production facilities that include chemical processing facilities, machine shops, production reactors, and laboratories. Current safety documentation must be maintained for the nuclear facilities at SRS. Fire Risk Analyses (FRAs) are used to support the safety documentation basis. These FRAs present the frequency that specified radiological and chemical consequences will be exceeded. The consequence values are based on mechanistic models assuming specific fire protection features fail to function as designed

  12. Waste management considerations in nuclear facility decommissioning

    Elder, H.K.; Murphy, E.S.

    1981-01-01

    Decommissioning of nuclear facilities involves the management of significant quantities of radioactive waste. This paper summarizes information on volumes of waste requiring disposal and waste management costs developed in a series of decommissioning studies performed for the U.S. Nuclear Regulatory Commission by the Pacific Northwest Laboratory. These studies indicate that waste management is an important cost factor in the decommissioning of nuclear facilities. Alternatives for managing decommissioning wastes are defined and recommendations are made for improvements in waste management practices

  13. Visitor centres at nuclear facility sites

    1993-01-01

    Communications strategies in the nuclear field are often based on the creation of visitor centres at nuclear facility sites. Today, the design, as well as the realization and management of such centres has become a specialized function, and its role is very complementary to the nuclear operator's. It also uses the latest technology in the field of audio-visual, experiment and interactivity. This publication contains the proceedings of an international seminar organized by the OECD Nuclear Energy Agency on the role of visitor centres at nuclear facility sites. It includes the main papers presented at this Seminar

  14. Nuclear energy: a world of service to humanity. 27th annual conference of the Canadian Nuclear Society and 30th Canadian Nuclear Society/Canadian Nuclear Association student conference

    2006-01-01

    The 27th Annual conference of the Canadian Nuclear Society was held on June 11-14, 2006 in Toronto, Ontario, Canada. The conference gathered close to 400 scientists, engineers, technologists and students interested in all aspects and applications of energy from the atom. The central objective of this conference was to provide a forum for exchange of views on how this technical enterprise can best serve the needs of humanity, now and in the future. The plenary sessions addressed broad industrial and commercial developments in the field. Over eighty papers were presented in 15 technical sessions on the following topics: safety analysis; plant refurbishment; control room operation; nuclear chemistry and materials; advanced reactor design; plant operation; reactor physics; safety analysis; nuclear instrumentation; and, nuclear general topics. Embedded in the conference was the 30th student conference, sponsored by the Canadian Nuclear Society and the Canadian Nuclear Association. Over thirty-five papers were presented in five sessions on the following topics: corrosion processes; control systems / physics / modelling; and, chemistry / chemical engineering

  15. Study on HVAC system in nuclear facility

    Baeg, S. Y.; Song, W. S.; Oh, Y. O.; Ju, Y. S.; Hong, K. P.

    2003-01-01

    Heating, Ventilation and Air Conditioning (HVAC) system in nuclear facility should be equipped and constructed more stable and allowable than that in common facility. The purpose of HVAC system is the maintenance of optimum working environment, the protection of worker against a contaminated air and the prevention of atmospheric contamination due to an outward ventilation, etc.. The basic scheme of a safety operation of nuclear facility is to prevent the atmospheric contamination even in low level. The adaptability of HVAC system which is in operation. In this study, the design requirements of HVAC system in nuclear facility and the HVAC systems in foreign countries are reviewed, and the results can be utilized in the design of HVAC system in nuclear facility

  16. Corrosion of copper under Canadian nuclear fuel waste disposal conditions

    King, F.; Litke, C.D.

    1990-01-01

    The corrosion of copper was studied under Canadian nuclear fuel waste disposal conditions. The groundwater in a Canadian waste vault is expected to be saline, with chloride concentrations from 0.1 to 1.0 mol/l. The container would be packed in a sand/clay buffer, and the maximum temperature on the copper surface would be 100C; tests were performed up to 150C. Radiation fields will initially be around 500 rad/h, and conditions will be oxidizing. Sulfides may be present. The minimum design lifetime for the container is 500 years. Most work has been done on uniform corrosion, although pitting has been considered. It was found that the rate of uniform corrosion in aerated NaCl at room temperature is limited by the rate of the anodic reaction, which is controlled mainly by the rate of transport of dissolved metal species away from the copper surface. The rate of corrosion should become controlled by the transport of oxygen to the copper surface only at very low oxygen concentrations. In the presence of gamma radiation the corrosion rate may never become cathodically transport limited. In compacted buffer material, the corrosion rate appears to be limited by the rate of transport of copper species away from the corroding surface. The authors recommend that long-term predictions of container lifetime should be based on the known rate-determining step for the overall corrosion process. 8 refs

  17. Nuclear physics accelerator facilities of the world

    1991-12-01

    this report is intended to provide a convenient summary of the world's major nuclear physics accelerator facility with emphasis on those facilities supported by the US Department of Energy (DOE). Previous editions of this report have contained only DOE facilities. However, as the extent of global collaborations in nuclear physics grows, gathering summary information on the world's nuclear physics accelerator facilities in one place is useful. Therefore, the present report adds facilities operated by the National Science Foundation (NSF) as well as the leading foreign facilities, with emphasis on foreign facilities that have significant outside user programs. The principal motivation for building and operating these facilities is, of course, basic research in nuclear physics. The scientific objectives for this research were recently reviewed by the DOE/NSF Nuclear Science Advisory Committee, who developed a long range plan, Nuclei, Nucleons, and Quarks -- Nuclear Science in the 1990's. Their report begins as follows: The central thrust of nuclear science is the study of strongly interacting matter and of the forces that govern its structure and dynamics; this agenda ranges from large- scale collective nuclear behavior through the motions of individual nucleons and mesons, atomic nuclei, to the underlying distribution of quarks and gluons. It extends to conditions at the extremes of temperature and density which are of significance to astrophysics and cosmology and are conducive to the creation of new forms of strongly interacting matter; and another important focus is on the study of the electroweak force, which plays an important role in nuclear stability, and on precision tests of fundamental interactions. The present report provides brief descriptions of the accelerator facilities available for carrying out this agenda and their research programs

  18. Final argument relating to the Canadian nuclear power program

    Robertson, J.A.L.

    1978-05-01

    This report is the second brief, and one of a number of documents, submitted by Atomic Energy of Canada Limited (AECL) to the Ontario Royal Commission on Electric Power Planning. It is intended to update the original brief (AECL--5800) with respect to those matters that emerged during the course of the hearings and which had not been fully anticipated in that brief, as well as to summarize the AECL position on the various issues. To enable it to qualify as a ''final argument'' it contains only evidence or material that has been presented to the Royal Commission and is provided with marginal notations identifying the source of each section. It is AECL's position that the Canadian nuclear power program provides a safe, proven and efficient means of making a needed contribution to electricity supply, while strengthening the economy through the deployment of indigenous technology and resources. (author)

  19. Chemistry research for the Canadian nuclear fuel waste management program

    Vikis, A.C.; Garisto, F.; Lemire, R.J.; Paquette, J.; Sagert, N.H.; Saluja, P.P.S.; Sunder, S.; Taylor, P.

    1988-01-01

    This publication reviews chemical research in support of the Canadian Nuclear Fuel Waste Management Program. The overall objective of this research is to develop the fundamental understanding required to demonstrate the suitability of waste immobilization media and processes, and to develop the chemical information required to predict the long-term behaviour of radionuclides in the geosphere after the waste form and the various engineered barriers containing it have failed. Key studies towards the above objective include experimental and theoretical studies of uranium dioxide oxidation/dissolution; compilation of thermodynamic databases and an experimental program to determine unavailable thermodynamic data; studies of hydrothermal alteration of minerals and radionuclide interactions with such minerals; and a study examining actinide colloid formation, as well as sorption of actinides on groundwater colloids

  20. Lifting devices in nuclear facilities

    The rule is valid for lifts, cranes, winches, rail travel trolleys, load lifting devices and fuel element changing devices for light-water reactors, insofar as these are used in plants to produce or to fission nuclear fuels or to process irradiated nuclear fuels or in the storage or other use of nuclear fuels. (LH) [de

  1. CANDU, an analysis of the Canadian nuclear program. Part I. Technical handbook

    Watters, M

    1975-12-01

    An excellent compilation is given of facts not easily found on the Canadian nuclear program. Some background physics and radiation biology are explained. The implications of using uranium, plutonium, and thorium as nuclear fuels are discussed. Heavy water production is briefly discussed, as is management of nuclear wastes. Overall, great emphasis is placed on explicating environmental effects and possible hazards of nuclear power.

  2. Importance of tests in nuclear facilities

    Guillemard, B.

    1985-10-01

    In nuclear facilities, safety related systems and equipments are subject, along their whole service-life, to numerous tests. This paper analyses the role of tests in the successive stages of design, construction, exploitation of a nuclear facility. It examines several aspects of test quality control: definition of needs, test planning, intrinsic quality of each test, control of interfaces (test are both the end and the starting point of many actions concerned by quality) and the application [fr

  3. Methodology and technology of decommissioning nuclear facilities

    1986-01-01

    The decommissioning and decontamination of nuclear facilities is a topic of great interest to many Member States of the International Atomic Energy Agency (IAEA) because of the large number of older nuclear facilities which are or soon will be retired from service. In response to increased international interest in decommissioning and to the needs of Member States, the IAEA's activities in this area have increased during the past few years and will be enhanced considerably in the future. A long range programme using an integrated systems approach covering all the technical, regulatory and safety steps associated with the decommissioning of nuclear facilities is being developed. The database resulting from this work is required so that Member States can decommission their nuclear facilities in a safe time and cost effective manner and the IAEA can effectively respond to requests for assistance. The report is a review of the current state of the art of the methodology and technology of decommissioning nuclear facilities including remote systems technology. This is the first report in the IAEA's expanded programme and was of benefit in outlining future activities. Certain aspects of the work reviewed in this report, such as the recycling of radioactive materials from decommissioning, will be examined in depth in future reports. The information presented should be useful to those responsible for or interested in planning or implementing the decommissioning of nuclear facilities

  4. Progress towards a new Canadian irradiation-research facility

    Lee, A.G.; Lidstone, R.F.

    1993-01-01

    As reported at the second meeting of the International Group on Research Reactors, Atomic Energy of Canada Limited (AECL) is evaluating its options for future irradiation facilities. During the past year significant progress has been made towards achieving consensus on the irradiation requirements for AECL's major research programs and interpreting those requirements in terms of desirable characteristics for experimental facilities in a research reactor. The next stage of the study involves identifying near-term and long-term options for irradiation-research facilities to meet the requirements. The near-term options include assessing the availability of the NRU reactor and the capabilities of existing research reactors. The long-term options include developing a new irradiation-research facility by adapting the technology base for the MAPLE-X10 reactor design. Because materials testing in support of CANDU power reactors dominates AECL's irradiation requirements, the new reactor concept is called the MAPLE Materials Testing Reactor (MAPLE-MTR). Parametric physics and engineering studies are in progress on alternative MAPLE-MTR configurations to assess the capabilities for the following types of test facilities: - fast-neutron sites, that accommodate materials-irradiation assemblies, - small-diameter vertical fuel test loops that accommodate multielement assemblies, - large-diameter vertical fuel test loops, each able to hold one or more CANDU fuel bundles, - horizontal test loops, each able to hold full-size CANDU fuel bundles or small-diameter multi-element assemblies, and - horizontal beam tubes

  5. Auxiliary facilities on nuclear ship 'MUTSU'

    Tsujimura, Shotaro; Takigami, Yoshio.

    1989-01-01

    The nuclear ship 'MUTSU' has been moored at SEKINEHAMA, MUTU City in AOMORI Prefecture and several tests and works are being carried out on the ship. The construction of the auxiliary facilities for these works on the ship was completed in safety in August 1988. After that the facilities have fulfilled their function. The outlines of design, fabrication and construction of the facilities are described in this paper. (author)

  6. Proceedings of the 32. annual conference of the Canadian Nuclear Association

    1992-01-01

    The conference proceedings comprise 34 papers, arranged under the following sessions: Plenary; The international CANDU program; Canadian used fuel management program; Public information advocates; Fuel and electricity supply; In which direction should reactors advance?; Canadian advanced nuclear research programs; International cooperation in operations; Safety in design, operation, regulation; Renovation of operating stations; CNS/CNA luncheon addresses. The individual papers have been abstracted separately

  7. Developments in the Canadian program for geological disposal of nuclear fuel waste

    Allan, C.J.; Nuttall, K.

    1996-01-01

    The Canadian Nuclear Fuel Waste Management Program is at the end of disposal concept and technology development and is now undergoing a comprehensive environmental review. This paper will review: the history of the Canadian program; the disposal concept and the associated technologies; the program achievements and the lessons learned; and the status of the environmental review. (author)

  8. Knowledge Management in Nuclear Facilities

    Strba, M.

    2007-01-01

    Rebirth of and return to nuclear energy conditioned by an increasing worldwide energy consumption and decreasing fuel sources such as crude oil, gas and oil has aroused the question how to maintain nuclear knowledge obtained by previous generations and at the same time to deliver it to their successors in as complete form as possible. (author)

  9. The Canadian Nuclear Safety Commission Compliance Program for Uranium Mines and Mills

    Schryer, D., E-mail: denis.schryer@cnsc-ccsn.gc.ca [Canadian Nuclear Safety Commission, Saskatoon, Saskatchewan (Canada)

    2014-05-15

    The Canadian Nuclear Safety Commission (CNSC) is the principal nuclear regulator in Canada. The CNSC is empowered through the Nuclear Safety and Control Act (NSCA) and its associated regulations, to regulate the entire nuclear cycle which includes: uranium mining and milling, uranium refining and processing, fuel fabrication, power generation and nuclear waste management. A CNSC uranium mine licence is required by a proponent to site, prepare, construct, operate, decommission and abandon this nuclear facility. The CNSC licence is the legal instrument that authorizes the regulated activities and incorporates conditions and regulatory controls. Following a favourable Commission Tribunal decision to issue a licence to authorize the licensed activities, CNSC develops and executes a compliance plan of the licensee’s programs and procedures. The CNSC compliance plan is risk-informed and applies its resources to the identified higher risk areas. The compliance program is designed to encourage compliance by integrating three components: promotion, verification and enforcement and articulates the CNSC expectations to attain and maintain compliance with its regulatory requirements. The licensee performance is assessed through compliance activities and reported to the Commission to inform the licensing process during licence renewal. The application of the ongoing compliance assessment and risk management model ensures that deviations from impact predictions are addressed in a timely manner. The Uranium Mines and Mills Division of the CNSC are preparing to meet the challenges of the planned expansion of their Canadian uranium mining industry. The presentation will discuss these challenges and the measures required to address them. The Uranium Mines and Mills Division (UMMD) have adopted a structured compliance framework which includes formal procedures to conduct site inspections. New UMMD staff are trained to apply the regulations to licensed sites and to manage non

  10. Nuclear astrophysics experiments with Pohang neutron facility

    Kim, Yeong Duk; Yoo, Gwang Ho

    1998-01-01

    Nuclear astrophysics experiments for fundamental understanding of Big Bang nucleosynthesis was performed at Pohang Neutron Facility. Laboratory experiments, inhomogeneous Big Bang nucleosynthesis and S-process were used for nucleosynthesis. For future study, more study on S-process for the desired data and nuclear network calculation are necessary

  11. Quality management in nuclear facilities decommissioning

    Garonis, Omar H.

    2002-01-01

    Internationally, the decommissioning organizations of nuclear facilities carry out the decommissioning according to the safety requirements established for the regulatory bodies. Some of them perform their activities in compliance with a quality assurance system. This work establishes standardization through a Specifications Requirement Document, for the management system of the nuclear facilities decommissioning organizations. It integrates with aspects of the quality, environmental, occupational safety and health management systems, and also makes these aspects compatible with all the requirements of the nuclear industry recommended for the International Atomic Energy Agency (IAEA). (author)

  12. Radioiodine removal in nuclear facilities

    1980-01-01

    Technical means are reviewed available for the retention of radioiodine in nuclear power plants and fuel reprocessing plants, its immobilization, storage, and disposal. The removal of iodine species from gaseous effluents of nuclear power plants using impregnated activated charcoal is dealt with. Various scrubbing techniques for trapping iodine from the head-end and dissolver off-gases are discussed as well as solid adsorbents for iodine which may be used to clean up other gaseous streams. Current practices and activities for radioiodine treatment and management in Belgian, Dutch, Swedish, USSR and UK nuclear installations are presented

  13. Significant incidents in nuclear fuel cycle facilities

    NONE

    1996-03-01

    In contrast to nuclear power plants, events in nuclear fuel cycle facilities are not well documented. The INES database covers all the nuclear fuel cycle facilities; however, it was developed in the early 1990s and does not contain information on events prior to that. The purpose of the present report is to collect significant events and analyze them in order to give a safety related overview of nuclear fuel cycle facilities. Significant incidents were selected using the following criteria: release of radioactive material or exposure to radiation; degradation of items important to safety; and deficiencies in design, quality assurance, etc. which include criticality incidents, fire, explosion, radioactive release and contamination. This report includes an explanation, where possible, of root causes, lessons learned and action taken. 4 refs, 4 tabs.

  14. Integrated engineering system for nuclear facilities building

    Tomura, H.; Miyamoto, A.; Futami, F.; Yasuda, S.; Ohtomo, T.

    1995-01-01

    In the construction of buildings for nuclear facilities in Japan, construction companies are generally in charge of the building engineering work, coordinating with plant engineering. An integrated system for buildings (PROMOTE: PROductive MOdeling system for Total nuclear Engineering) described here is a building engineering system including the entire life cycle of buildings for nuclear facilities. A Three-dimensional (3D) building model (PRO-model) is to be in the core of the system (PROMOTE). Data sharing in the PROMOTE is also done with plant engineering systems. By providing these basic technical foundations, PROMOTE is oriented toward offering rational, highquality engineering for the projects. The aim of the system is to provide a technical foundation in building engineering. This paper discusses the characteristics of buildings for nuclear facilities and the outline of the PROMOTE. (author)

  15. Significant incidents in nuclear fuel cycle facilities

    1996-03-01

    In contrast to nuclear power plants, events in nuclear fuel cycle facilities are not well documented. The INES database covers all the nuclear fuel cycle facilities; however, it was developed in the early 1990s and does not contain information on events prior to that. The purpose of the present report is to collect significant events and analyze them in order to give a safety related overview of nuclear fuel cycle facilities. Significant incidents were selected using the following criteria: release of radioactive material or exposure to radiation; degradation of items important to safety; and deficiencies in design, quality assurance, etc. which include criticality incidents, fire, explosion, radioactive release and contamination. This report includes an explanation, where possible, of root causes, lessons learned and action taken. 4 refs, 4 tabs

  16. Childhood leukaemia around nuclear facilities

    Wojcik, Andrzej (Centre for Radiation Protection Research, GMT Dept., Stockholm Univ., Stockholm (Sweden)); Feychting, Maria (Inst. of Environmental Medicine, Karolinska Inst., Stockholm (Sweden))

    2010-06-15

    In December 2007 the German Federal Office for Radiation Protection (BfS) published a report on the incidence of childhood cancers among children living in the vicinity of 16 German nuclear power plants. The results show a significantly enhanced risk of leukaemia in children aged below 5 years, who live within 5 km from a nuclear power plant. The study is known as KiKK (Epidemiologische Studie zu Kinderkrebs in der Umgebung von Kernkraftwerken) and stirred considerable concern about the safety of nuclear installations. In this review we summarise the present state-of-the art regarding childhood leukaemia in the vicinity of nuclear installations and present the main results of the KiKK study with a critical evaluation

  17. Childhood leukaemia around nuclear facilities

    Wojcik, Andrzej; Feychting, Maria

    2010-06-01

    In December 2007 the German Federal Office for Radiation Protection (BfS) published a report on the incidence of childhood cancers among children living in the vicinity of 16 German nuclear power plants. The results show a significantly enhanced risk of leukaemia in children aged below 5 years, who live within 5 km from a nuclear power plant. The study is known as KiKK (Epidemiologische Studie zu Kinderkrebs in der Umgebung von Kernkraftwerken) and stirred considerable concern about the safety of nuclear installations. In this review we summarise the present state-of-the art regarding childhood leukaemia in the vicinity of nuclear installations and present the main results of the KiKK study with a critical evaluation

  18. Technical Cybersecurity Controls for Nuclear Facilities

    Oh, Jinseok; Ryou, Jaecheol; Kim, Youngmi; Jeong, Choonghei

    2014-01-01

    To strengthen cybersecurity for nuclear facilities, many countries take a regulatory approach. For example, US Government issued several regulations . Title 10, of the Code of Federal Regulations, Section 73.54, 'Protection of Digital Computer and Communication Systems and Networks (10 CFR 73.54) for cybersecurity requirements and Regulatory Guide 5.71 (RG. 5.71) for cybersecurity guidance and so on. In the case of Korea, Korean Government issued '8.22 Cybersecurity of I and C systems (KINS/RG-NO8.22). In particular, Reg. 5.71 provides a list of security controls to address the potential cyber risks to a nuclear facilities. Implementing and adopting security controls, we can improve the level of cybersecurity for nuclear facilities. RG 5.71 follows the recommendation of NIST SP 800-53. NIST standard provides security controls for IT systems. And NRC staff tailored the controls in NIST standards to unique environments of nuclear facilities. In this paper, we are going to analysis and compare NRC RG 5.71 and NIST SP800-53, in particular, for technical security controls. If RG 5.71 omits the specific security control that is included in SP800-53, we would review that omitting is adequate or not. If RG 5.71 includes the specific security control that is not included in SP800-53, we would also review the rationale. And we are going to some security controls to strengthen cybersecurity of nuclear facilities. In this paper, we compared and analyzed of two regulation in technical security controls. RG 5.71 that is based on NIST standard provides well-understood security controls for nuclear facility. But some omitting from NIST standard can threaten security state of nuclear facility

  19. Technical Cybersecurity Controls for Nuclear Facilities

    Oh, Jinseok; Ryou, Jaecheol [Chungnam National Univ., Daejeon (Korea, Republic of); Kim, Youngmi; Jeong, Choonghei [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2014-05-15

    To strengthen cybersecurity for nuclear facilities, many countries take a regulatory approach. For example, US Government issued several regulations . Title 10, of the Code of Federal Regulations, Section 73.54, 'Protection of Digital Computer and Communication Systems and Networks (10 CFR 73.54) for cybersecurity requirements and Regulatory Guide 5.71 (RG. 5.71) for cybersecurity guidance and so on. In the case of Korea, Korean Government issued '8.22 Cybersecurity of I and C systems (KINS/RG-NO8.22). In particular, Reg. 5.71 provides a list of security controls to address the potential cyber risks to a nuclear facilities. Implementing and adopting security controls, we can improve the level of cybersecurity for nuclear facilities. RG 5.71 follows the recommendation of NIST SP 800-53. NIST standard provides security controls for IT systems. And NRC staff tailored the controls in NIST standards to unique environments of nuclear facilities. In this paper, we are going to analysis and compare NRC RG 5.71 and NIST SP800-53, in particular, for technical security controls. If RG 5.71 omits the specific security control that is included in SP800-53, we would review that omitting is adequate or not. If RG 5.71 includes the specific security control that is not included in SP800-53, we would also review the rationale. And we are going to some security controls to strengthen cybersecurity of nuclear facilities. In this paper, we compared and analyzed of two regulation in technical security controls. RG 5.71 that is based on NIST standard provides well-understood security controls for nuclear facility. But some omitting from NIST standard can threaten security state of nuclear facility.

  20. Computerized health physics record system at a Canadian fabrication facility

    Thind, K.S.

    1984-01-01

    This poster session will describe the types of Health Physics data input into a Hewlett-Packard 3000 computer. The Health Physics data base at this facility includes the following: employee hours data, airborne uranium concentrations, external dosemetry (badge readings), internal dosemetry (bioassay) and environmental health physics (stack sample results) data. It will describe the types of outputs achievable in the form of various reports, such as: individual employee health physics report for a given period, a general health physics summary report for a given period, individual urinalysis report, local air concentration report and graphs. The use of this computerized health physics record system in the overall radiation protection program at this facility is discussed

  1. Radiation protection at nuclear fuel cycle facilities

    Endo, K.; Momose, T.; Furuta, S.

    2011-01-01

    Radiation protection methodologies concerning individual monitoring, workplace monitoring and environmental monitoring in nuclear fuel facilities have been developed and applied to facilities in the Nuclear Fuel Cycle Engineering Laboratories (NCL) of Japan Atomic Energy Agency (JAEA) for over 40 y. External exposure to photon, beta ray and neutron and internal exposure to alpha emitter are important issues for radiation protection at these facilities. Monitoring of airborne and surface contamination by alpha and beta/photon emitters at workplace is also essential to avoid internal exposure. A critical accident alarm system developed by JAEA has been proved through application at the facilities for a long time. A centralised area monitoring system is effective for emergency situations. Air and liquid effluents from facilities are monitored by continuous monitors or sampling methods to comply with regulations. Effluent monitoring has been carried out for 40 y to assess the radiological impacts on the public and the environment due to plant operation. (authors)

  2. Building a medical system for nuclear facilities

    Maeda, Mitsuya

    2016-01-01

    To build a medical system for nuclear facilities, I explained what kinds of actions were performed with the TEPCO Fukushima Daiichi Nuclear Power Plant Accident and what kinds of actions are going to be performed in the future. We examined the health and medical care of the emergency workers in nuclear facilities including TEPCO Fukushima Daiichi Nuclear Power Plant from 2014 to 2015 in the Ministry of Health, Labour and Welfare (MHLW). We carried out a detailed hearing from stakeholders of electric companies and medical institutions about the medical system in nuclear facilities carrying out urgent activities. It has been said that the electric company is responsible to maintain the medical system for affected workers in nuclear facilities. However, TEPCO could not find the medical staff, such as doctors, by their own effort at the TEPCO Fukushima Daiichi Nuclear Power Plant Accident. The network of doctors familiar with emergency medical care support dispatched the medical staff after July of 2011. The stakeholders indicated that the following six tasks must be resolved: (1) the fact that no electric company performs the action of bringing up medical staff who can be dispatched into nuclear facilities in emergencies in 2015; (2) bringing up personnel in charge of radiation management and logistics other than the medical staff, such as doctors; (3) cooperation with the community medicine system given the light and shade by nuclear facilities; (4) performing training for the many concurrent wounded based on the scenario of a severe accident; (5) indicating both the condition of the contract and the guarantee of status that is appropriate for dispatched medical staffs; and (6) clarifying the organization of the network of stakeholders. The stakeholders showed the future directionality as follows: (1) To recruit the medical staff expected to be dispatched into nuclear facilities, (2) to carry out the discussion and conveyance training to strengthen cooperation with

  3. Establishing and Advancing Electronic Nuclear Material Accounting Capabilities: A Canadian Perspective

    Sample, J.

    2015-01-01

    Under safeguards agreements that the Government of Canada has with the International Atomic Energy Agency (IAEA), and nuclear cooperation agreements with other states, the Canadian Nuclear Safety Commission (CNSC) is required to track the inventory and movement of all safeguarded material. As safeguards programmes evolve, including the implementation of Integrated Safeguards, the scope of the reporting requirements for facilities within Canada has also increased. At the same time, ensuring the secure transmission of the associated data continues to be an overarching factor. The changes that are occurring in the nuclear material accounting (NMA) landscape have necessitated a modernization of Canada's accounting and reporting system, with the objective of creating a more effective and efficient system, while at the same time maintaining the security of prescribed information. After a review of the environment, the CNSC embarked on a project that would encourage facilities to transition away from traditional modes of NMA reporting and adopt an electronic approach. This paper will discuss how the changes to Canada's NMA infrastructure were identified and implemented internally to allow for optimized electronic reporting. Improvements included the development of the regulatory and guidance documents, the overhaul of the reporting forms, the upgrade of the CNSC's NMA database, and the development of an electronic reporting platform that leveraged existing technologies. The paper will also discuss the logistics of engaging stakeholders throughout the process, launching the system and soliciting feedback for future system improvements. Special consideration will be given to the benefits realized by both the CNSC and facilities who have voluntarily embraced electronic reporting. The final objective of this paper will be to identify the challenges that were faced by the CNSC and the nuclear industry as the system changes were implemented and to highlight how

  4. The Physical Protection of Nuclear Material and Nuclear Facilities

    1999-08-01

    Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international co-operation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and nuclear materials, particularly when such materials are transported across national frontiers

  5. The Physical Protection of Nuclear Material and Nuclear Facilities

    1999-06-01

    Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international co-operation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and nuclear materials, particularly when such materials are transported across national frontiers [es

  6. The Physical Protection of Nuclear Material and Nuclear Facilities

    1999-06-01

    Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international co-operation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and nuclear materials, particularly when such materials are transported across national frontiers

  7. Methodology for analyzing risk at nuclear facilities

    Yoo, Hosik; Lee, Nayoung; Ham, Taekyu; Seo, Janghoon

    2015-01-01

    Highlights: • A new methodology for evaluating the risk at nuclear facilities was developed. • Five measures reflecting all factors that should be concerned to assess risk were developed. • The attributes on NMAC and nuclear security culture are included as attributes for analyzing. • The newly developed methodology can be used to evaluate risk of both existing facility and future nuclear system. - Abstract: A methodology for evaluating risks at nuclear facilities is developed in this work. A series of measures is drawn from the analysis of factors that determine risks. Five measures are created to evaluate risks at nuclear facilities. These include the legal and institutional framework, material control, physical protection system effectiveness, human resources, and consequences. Evaluation attributes are developed for each measure and specific values are given in order to calculate the risk value quantitatively. Questionnaires are drawn up on whether or not a state has properly established a legal and regulatory framework (based on international standards). These questionnaires can be a useful measure for comparing the status of the physical protection regime between two countries. Analyzing an insider threat is not an easy task and no methodology has been developed for this purpose. In this study, attributes that could quantitatively evaluate an insider threat, in the case of an unauthorized removal of nuclear materials, are developed by adopting the Nuclear Material Accounting & Control (NMAC) system. The effectiveness of a physical protection system, P(E), could be analyzed by calculating the probability of interruption, P(I), and the probability of neutralization, P(N). In this study, the Tool for Evaluating Security System (TESS) code developed by KINAC is used to calculate P(I) and P(N). Consequence is an important measure used to analyze risks at nuclear facilities. This measure comprises radiological, economic, and social damage. Social and

  8. Executive brief to federal government 'the Canadian nuclear industry - a national asset'

    1985-03-01

    Over a period of 40 years Canada has developed a remarkable nuclear industry. In keeping with our mining heritage, we are the world's leading uranium producer, with the highest grade orebodies in existence still waiting to be tapped. In the realm of high technology development, our CANDU reactor is second to none. Year after year Canadian CANDUs dominate the 'top 10' performance records world-wide. The nuclear industry has created direct employment for over 30,000 Canadians. The 'high tech' sectors of the industry are now vigorously seeking export markets for their products and services. As the world recovers from the recent prolonged recession, electricity demand is rising. Once again electricity is the engine of growth. Already utilities are planning to add new generating capacity. Canadian nuclear resources, technology and skilled people are proven and available. By seizing the opportunities which are opening up for us, a properly recognized nuclear industry can make a vital contribution to Canada's economic renewal. This brief has been prepared by the Canadian Nuclear Association (CNA) in response to the challenge issued to Canadians in Finance Minister Michael Wilson's document 'A New Direction for Canada'. This brief responds in terms of the major policy issues and opportunities as seen by the Canadian nuclear industry

  9. Characterization of Canadian coals by nuclear magnetic resonance spectroscopy

    Furimsky, E.; Ripmeester, J.

    1983-06-01

    Apparent aromaticities of a series of Canadian coals of different rank were estimated by solid state nuclear magnetic resonance spectroscopy. The aromaticities varied from 0.57 for a lignite up to 0.86 for a semi-anthracite coal. The aromaticities correlated well with fixed carbon and oxygen content of the coals as well as with the mean reflectance of the coals. Correlations were also established between aromaticities and the H/C and H/SUB/a/SUB/r/SUB/u/C/SUB/a/SUB/r ratios of the coals. Uncertainties in calculation of the hypothetical H/SUB/a/SUB/r/SUB/u/C/SUB/a/SUB/r ratios, from experimental data were pointed out. Structural parameters of the chars derived from the coals by pyrolysis at 535 C were, also, estimated. The H/C and H/SUB/a/SUB/r/SUB/u/C/SUB/a/SUB/r ratios of the chars were markedly lower than those of coals. This was complemented by higher apparent aromaticities of the chars compared with the coals. (21 refs.)

  10. Computer Security at Nuclear Facilities (French Edition)

    2013-01-01

    The possibility that nuclear or other radioactive material could be used for malicious purposes cannot be ruled out in the current global situation. States have responded to this risk by engaging in a collective commitment to strengthen the protection and control of such material and to respond effectively to nuclear security events. States have agreed to strengthen existing instruments and have established new international legal instruments to enhance nuclear security worldwide. Nuclear security is fundamental in the management of nuclear technologies and in applications where nuclear or other radioactive material is used or transported. Through its Nuclear Security Programme, the IAEA supports States to establish, maintain and sustain an effective nuclear security regime. The IAEA has adopted a comprehensive approach to nuclear security. This recognizes that an effective national nuclear security regime builds on: the implementation of relevant international legal instruments; information protection; physical protection; material accounting and control; detection of and response to trafficking in such material; national response plans; and contingency measures. With its Nuclear Security Series, the IAEA aims to assist States in implementing and sustaining such a regime in a coherent and integrated manner. The IAEA Nuclear Security Series comprises Nuclear Security Fundamentals, which include objectives and essential elements of a State's nuclear security regime; Recommendations; Implementing Guides; and Technical Guidance. Each State carries the full responsibility for nuclear security, specifically: to provide for the security of nuclear and other radioactive material and associated facilities and activities; to ensure the security of such material in use, storage or in transport; to combat illicit trafficking and the inadvertent movement of such material; and to be prepared to respond to a nuclear security event. This publication is in the Technical Guidance

  11. Nuclear material inventory estimation in a nuclear fuel reprocessing facility

    Bennett, J.E.; Beyerlein, A.L.

    1981-01-01

    A new approach in the application of modern system identification and estimation techniques is proposed to help nuclear reprocessing facilities meet the nuclear accountability requirement proposed by the International Atomic Energy Agency. The proposed identification and estimation method considers the material inventory in a portion of the chemical separations area of a reprocessing facility. The method addresses the nonlinear aspects of the problem, the time delay through the separation facility, and the lack of measurement access. The method utilizes only input-output measured data and knowledge of the uncertainties associated with the process and measured data. 14 refs

  12. Operational status of nuclear facilities in Japan. 2008 edition

    2008-01-01

    This document is a summary of the outline of the safety regulation administration of nuclear facilities as well as various data on the commercial nuclear power reactor facilities, research and development nuclear power reactor facilities, fabrication facilities, reprocessing facilities, and disposal facilities in fiscal year 2007 (from April 2007 to March 2008). I sincerely hope this document is used widely by many people engaged in work related to ensuring nuclear safety. (J.P.N.)

  13. Operational status of nuclear facilities in Japan. 2010 edition

    2010-01-01

    This document is a summary of the outline of the safety regulation administration of nuclear facilities as well as various data on the commercial nuclear power reactor facilities, research and development nuclear power reactor facilities, fabrication facilities, reprocessing facilities, and disposal facilities in fiscal year 2009 (from April 2009 to March 2010). We sincerely hope this document is used widely by many people engaged in work related to ensuring nuclear safety. (author)

  14. Over view of nuclear fuel cycle examination facility at KAERI

    Lee, Key-Soon; Kim, Eun-Ga; Joe, Kih-Soo; Kim, Kil-Jeong; Kim, Ki-Hong; Min, Duk-Ki [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-09-01

    Nuclear fuel cycle examination facilities at the Korea Atomic Energy Research Institute (KAERI) consist of two post-irradiation examination facilities (IMEF and PIEF), one chemistry research facility (CRF), one radiowaste treatment facility (RWTF) and one radioactive waste form examination facility (RWEF). This paper presents the outline of the nuclear fuel cycle examination facilities in KAERI. (author)

  15. Performance of Canadian commercial nuclear units and heavy water plants

    Woodhead, L.W.; Ingolfsrud, L.J.

    The operating history of Canadian commercial CANDU type reactors, i.e. Pickering generating station-A, is described. Capacity factors and unit energy costs are analyzed in detail. Equipment performance highlights are given. The performance of the two Canadian heavy water plants is described and five more are under construction or planned. (E.C.B.)

  16. Brennilis nuclear facilities. 2009 annual report

    2010-01-01

    This annual report is established on account of article 21 of the 2006-686 French law from June 13, 2006, relative to the transparency and safety in the nuclear domain. It describes, first, the nuclear facilities of Brennilis, and then the measures taken to ensure their safety (personnel radioprotection, actions implemented for nuclear safety improvement, organisation in crisis situation, external and internal controls, technical assessment of the facilities, administrative procedures carried out in 2009), incidents and accidents registered in 2009, radioactive and chemical effluents released by the facilities in the environment, other pollutions, management of radioactive wastes, and, finally, the actions carried out in the domain of transparency and public information. A glossary and the viewpoint of the Committee of Hygiene, safety and working conditions about the content of the document conclude the report. (J.S.)

  17. Civaux nuclear facilities. 2009 annual report

    2010-01-01

    This annual report is established on account of article 21 of the 2006-686 French law from June 13, 2006, relative to the transparency and safety in the nuclear domain. It describes, first, the nuclear facilities of Civaux, and then the measures taken to ensure their safety (personnel radioprotection, actions implemented for nuclear safety improvement, organisation in crisis situation, external and internal controls, technical assessment of the facilities, administrative procedures carried out in 2009), incidents and accidents registered in 2009, radioactive and chemical effluents released by the facilities in the environment, other pollutions, management of radioactive wastes, and, finally, the actions carried out in the domain of transparency and public information. A glossary and the viewpoint of the Committee of Hygiene, safety and working conditions about the content of the document conclude the report. (J.S.)

  18. Chooz nuclear facilities. 2009 annual report

    2010-01-01

    This annual report is established on account of article 21 of the 2006-686 French law from June 13, 2006, relative to the transparency and safety in the nuclear domain. It describes, first, the nuclear facilities of Chooz, and then the measures taken to ensure their safety (personnel radioprotection, actions implemented for nuclear safety improvement, organisation in crisis situation, external and internal controls, technical assessment of the facilities, administrative procedures carried out in 2009), incidents and accidents registered in 2009, radioactive and chemical effluents released by the facilities in the environment, other pollutions, management of radioactive wastes, and, finally, the actions carried out in the domain of transparency and public information. A glossary and the viewpoint of the Committee of Hygiene, safety and working conditions about the content of the document conclude the report. (J.S.)

  19. Environmental monitoring around the Swedish Nuclear Facilities

    Bondesson, A.; Luening, M.; Wallberg, L.; Wijk, H.

    1999-01-01

    The environmental monitoring programme for the nuclear facilities has shown that the radioactive discharges increase the concentrations of some radionuclides in the local marine environment around the Swedish nuclear facilities. Samples from the terrestrial environment rarely show increased radionuclide concentrations. From a radiological point of view the most important nuclide in the environmental samples usually is CS-137. However, the largest part of the present concentrations of Cs-137 in the Swedish environment originate from the Chernobyl accident. The concentrations of radionuclides that can be found in biota around the nuclear facilities are much lower than the concentration levels that are known to give acute damage to organisms. The total radiation doses from the discharges of radionuclides are small. (au)

  20. Institutionalizing Safeguards By Design for Nuclear Facilities

    Morgan, James B.; Kovacic, Donald N.; Whitaker, J. Michael

    2008-01-01

    Safeguards for nuclear facilities can be significantly improved by developing and implementing methodologies for integrating proliferation resistance into the design of new facilities. This paper proposes a method to systematically analyze a facility's processes, systems, equipment, structures and management controls to ensure that all relevant proliferation scenarios that could potentially result in unacceptable consequences have been identified, evaluated and mitigated. This approach could be institutionalized into a country's regulatory structure similar to the way facilities are licensed to operate safely and are monitored through inspections and incident reporting to ensure compliance with domestic and international safeguards. Furthermore, taking credit for existing systems and equipment that have been analyzed and approved to assure a facility's reliable and safe operations will reduce the overall cost of implementing intrinsic and extrinsic proliferation-resistant features. The ultimate goal is to integrate safety, reliability, security and safeguards operations into the design of new facilities to effectively and efficiently prevent diversion, theft and misuse of nuclear material and sensitive technologies at both the facility and state level. To facilitate this approach at the facility level, this paper discusses an integrated proliferation resistance analysis (IPRA) process. If effectively implemented, this integrated approach will also facilitate the application of International Atomic Energy Agency (IAEA) safeguards

  1. Intervention of the Canadian Nuclear Association to the National Energy Board

    1982-01-01

    This submission from the Canadian Nuclear Association to the National Energy Board of Canada was made in support of the application by the New Brunswick Electric Power Commission to increase its electricity exports from the Point Lepreau nuclear station to the New England states from 205 MW to 335 MW. The Canadian Nuclear Association felt that their support was justified in view of the fact that the CANDU nuclear reactor had proven itself to be a safe, reliable and economic source of electric generation. They felt the 630 MW CANDU station at Point Lepreau, New Brunswick would have sufficient generating capacity to export 335 MW for a ten-year period

  2. Physical activity opportunities in Canadian childcare facilities: a provincial/territorial review of legislation.

    Vanderloo, Leigh M; Tucker, Patricia; Ismail, Ali; van Zandvroort, Melissa M

    2012-05-01

    Preschoolers spend a substantial portion of their day in childcare; therefore, these centers are an ideal venue to encourage healthy active behaviors. It is important that provinces'/territories' childcare legislation encourage physical activity (PA) opportunities. The purpose of this study was to review Canadian provincial/territorial childcare legislation regarding PA participation. Specifically, this review sought to 1) appraise each provincial/territorial childcare regulation for PA requirements, 2) compare such regulations with the NASPE PA guidelines, and 3) appraise these regulations regarding PA infrastructure. A review of all provincial/territorial childcare legislation was performed. Each document was reviewed separately by 2 researchers, and the PA regulations were coded and summarized. The specific provincial/territorial PA requirements (eg, type/frequency of activity) were compared with the NASPE guidelines. PA legislation for Canadian childcare facilities varies greatly. Eight of the thirteen provinces/territories provide PA recommendations; however, none provided specific time requirements for daily PA. All provinces/territories did require access to an outdoor play space. All Canadian provinces/territories lack specific PA guidelines for childcare facilities. The development, implementation, and enforcement of national PA legislation for childcare facilities may aid in tackling the childhood obesity epidemic and assist childcare staff in supporting and encouraging PA participation.

  3. Conducting Computer Security Assessments at Nuclear Facilities

    2016-06-01

    Computer security is increasingly recognized as a key component in nuclear security. As technology advances, it is anticipated that computer and computing systems will be used to an even greater degree in all aspects of plant operations including safety and security systems. A rigorous and comprehensive assessment process can assist in strengthening the effectiveness of the computer security programme. This publication outlines a methodology for conducting computer security assessments at nuclear facilities. The methodology can likewise be easily adapted to provide assessments at facilities with other radioactive materials

  4. Quality Assurance for Operation of Nuclear Facilities

    Park, C. G.; Kwon, H. I.; Kim, K. H.; Oh, Y. W.; Lee, Y. G.; Ha, J. H.; Lim, N. J.

    2008-12-01

    This report describes QA activities performed within 'Quality Assurance for Nuclear facility project' and results thereof. Efforts were made to maintain and improve quality system of nuclear facilities. Varification activities whether quality system was implemented in compliance with requirements. QA department assisted KOLAS accredited testing and calibration laboratories, ISO 9001 quality system, establishment of QA programs for R and D, and carried out reviews and surveys for development of quality assurance technologies. Major items of this report are as follows : - Development and Improvement of QA Programs - QA Activities - Assessment of Effectiveness and Adequacy for QA Programs

  5. Emergency planning and preparedness for nuclear facilities

    Koelzer, W.

    1988-01-01

    Nuclear installations are designed, constructed and operated in such a way that the probability for an incident or accident is very low and the probability for a severe accident with catastrophic consequences is extremely small. These accidents represent the residual risk of the nuclear installation, and this residual risk can be decreased on one hand by a better design, construction and operation and on the other hand by planning and taking emergency measures inside the facility and in the environment of the facility. By way of introduction and definition it may be indicated to define some terms pertaining to the subject in order to make for more uniform understanding. (orig./DG)

  6. Nuclear power and the Canadian public. A national and regional assessment of public attitudes and perceptions of the use of nuclear power for the production of electricity

    Greer-Wootten, B; Mitson, L [York Univ., Toronto, Ontario (Canada)

    1976-06-01

    Over 2,100 persons from the Canadian public aged 18 years and over were interviewed to ascertain the opinions and attitudes of Canadians toward the use of nuclear power for generating electricity. The results of this survey are presented.

  7. Finally, nuclear engineering textbooks with a Canadian flavour{exclamation_point}

    Bonin, H.W. [Royal Military College of Canada, Dept. of Chemistry and Chemical Engineering, Kingston, Ontario (Canada)

    2002-07-01

    The need for nuclear engineering textbooks more appropriate to the Canadian nuclear industry context and the CANDU nuclear reactor program has long been felt not only among the universities offering nuclear engineering programs at the graduate level, but also within the Canadian nuclear industry itself. Coverage of the CANDU reactor system in the textbooks presently supporting teaching is limited to a brief description of the concept. Course instructors usually complement these textbooks with course notes written from their personal experience from past employment within the nuclear industry and from their research interests In the last ten years, the Canadian nuclear industry has been involved on an increasing basis with the issue of the technology transfer to foreign countries which have purchased CANDU reactors or have been in the process of purchasing one or several CANDUs. For some of these countries, the 'turn key' approach is required, in which the Canadian nuclear industry looks after everything up to the commissioning of the nuclear power plant, including the education and training of local nuclear engineers and plant personnel. Atomic Energy of Canada Limited (AECL) in particular has dispatched some personnel tasked to prepare and give short courses on some specific aspects of CANDU design and operation, but a lack of consistency was observed as different persons prepared and gave the courses rather independently. To address the many problems tied with nuclear engineering education, the CANTEACH program was set up involving major partners of the Canadian nuclear industry. Parts of the activities foreseen by CANTEACH consist in the writing of nuclear engineering textbooks and associated computer-based pedagogical material. The present paper discusses the main parts of two textbooks being produced, one in reactor physics at steady state and the other on nuclear fuel management. (author)

  8. Life Management and Safety of Nuclear Facilities

    Fabbri, S.; Diluch, A.; Vega, G., E-mail: fabbri@cnea.gov.ar [Comisión Nacional de Energía Atómica, Buenos Aires (Argentina)

    2014-10-15

    The nuclear programme in Argentina includes: nuclear power and related supplies, medical and industrial applications, waste management, research and development and human training. Nuclear facilities require life management programs that allow a safe operation. Safety is the first priority for designers and operators. This can be attained with defence in depth: regular inspections and maintenance procedures to minimize failure risks. CNEA objectives in this area are to possess the necessary capability to give safe and fast technical support. Within this scheme, one of the main activities undertaken by CNEA is to provide technological assistance to the nuclear plants and research reactors. As a consequence of an increasing concern about safety and ageing a Life Management Department for safe operation was created to take care of these subjects. The goal is to elaborate a Safety Evaluation Process for the critical components of nuclear plants and other facilities. The overall objectives of a safety process are to ensure a continuous safe, reliable and effective operation of nuclear facilities and it means the implementation of the defence in deep concept to enhance safety for the protection of the public, the workers and the environment. (author)

  9. Stakeholder involvement in decommissioning nuclear facilities

    2007-01-01

    Significant numbers of nuclear facilities will need to be decommissioned in the coming decades. In this context, NEA member countries are placing increasing emphasis on the involvement of stakeholders in the associated decision procedures. This study reviews decommissioning experience with a view to identifying stakeholder concerns and best practice in addressing them. The lessons learnt about the end of the facility life cycle can also contribute to better foresight in siting and building new facilities. This report will be of interest to all major players in the field of decommissioning, in particular policy makers, implementers, regulators and representatives of local host communities

  10. Nuclear energy: Environmental issues at DOE's nuclear defense facilities

    1986-01-01

    GAO's review of nine Department of Energy defense facilities identified a number of significant environmental issues: (1) eight facilities have groundwater contaminated with radioactive and/or hazardous substances to high levels; (2) six facilities have soil contamination in unexpected areas, including offsite locations; (3) four facilities are not in full compliance with the Clean Water Act; and (4) all nine facilities are significantly changing their waste disposal practices to obtain a permit under the Resource Conservation and Recovery Act. GAO is recommending that DOE develop and overall groundwater and soil protection strategy that would provide a better perspective on the environmental risks and impacts associated with operating DOE's nuclear defense facilities. GAO also recommends that DOE allow outside independent inspections of the disposal practices used for any waste DOE self-regulates and revise its order governing the management of hazardous and mixed waste

  11. SETT facility of International Nuclear Security Academy

    Seo, Hyung Min

    2012-01-01

    After the Cold War was put to an end, the international community, especially the Western world, was concerned about Soviet nuclear materials falling into wrong hands, especially of terrorists. Later, the growing threat posed by terrorist networks such as the Taliban and al Qaeda led to a global campaign to deny such networks materials which may be used for the development of Weapons of Mass Destruction (WMD). The 9 11 attacks made a section of the international community highly apprehensive of WMD terrorism, especially its nuclear version. From this point of view, it is clear that nuclear facilities which contain nuclear materials are very attractive targets for those who have intention of nuclear terror

  12. SETT facility of International Nuclear Security Academy

    Seo, Hyung Min [Korea Institute of Nuclear Non-proliferation and Control, Daejeon (Korea, Republic of)

    2012-05-15

    After the Cold War was put to an end, the international community, especially the Western world, was concerned about Soviet nuclear materials falling into wrong hands, especially of terrorists. Later, the growing threat posed by terrorist networks such as the Taliban and al Qaeda led to a global campaign to deny such networks materials which may be used for the development of Weapons of Mass Destruction (WMD). The 9 11 attacks made a section of the international community highly apprehensive of WMD terrorism, especially its nuclear version. From this point of view, it is clear that nuclear facilities which contain nuclear materials are very attractive targets for those who have intention of nuclear terror

  13. Canadian--American relations and the nuclear weapons controversy, 1958--1963

    Ghent, J.M.

    1976-01-01

    This study attempts to explain the nuclear weapons controversy as it developed between 1958 and 1963. The nuclear controversy centered around Canada's acceptance of a nuclear role, within the American alliance system, for the Canadian armed forces. In the period 1958-1959, when the critical weapons decisions were being taken, Canadian political authorities lost control of the policy-making process, permitting the Canadian and American military bureacracies to initiate nuclear plans suited to their common needs and objectives. Prime Minister Diefenbaker's reluctance to arm the systems acquired by transborder bureaucratic coalition is also re-examined. Previous analysts have regarded the government's hesitations over nuclear weapons as the product of Diefenbaker's personal antagonism towards President Kennedy or as a futile attempt to reverse the process of continental integration. The opening of the Kennedy papers reveals the degree to which Diefenbaker was committed to close Canadian-American cooperation and the effort he made to overcome the president's hostility towards him. This study emphasizes the importance of Diefenbaker's sensitivity to public, parliamentary, and cabinet opposition to nuclear arms. The secret U.S. demand for nuclear bases in Labrador and Newfoundland is revealed. Thus the question of nuclear storage in Canada for Canadian forces was complicated by U.S. insistence that Canada simultaneously provide nuclear storage for the strategic forces of the U.S. Finally, the extent of American responsibility for Diefenbaker's demise is re-assessed, and the conclusion is reached that the U.S., through Canadian-American military interaction and the initiative of the ambassador in Ottawa, did in fact help to bring down the government of Canada

  14. Neutron fluence measurement in nuclear facilities

    Camacho L, M.E.

    1997-01-01

    The objective of present work is to determine the fluence of neutrons in nuclear facilities using two neutron detectors designed and built at Instituto Nacional de Investigaciones Nucleares (ININ), Mexico. The two neutron detectors are of the passive type, based on solid state nuclear tracks detectors (SSNTD). One of the two neutron detectors was used to determine the fluence distribution of the ports at the nuclear research reactor TRIGA Mark III, which belongs to ININ. In these facilities is important to know the neutron fluence distribution characteristic to carried out diverse kind of research activities. The second neutron detector was employed in order to carry out environmental neutron surveillance. The detector has the property to separate the thermal, intermediate and fast components of the neutron fluence. This detector was used to measure the neutron fluence at hundred points around the primary container of the first Mexican Nuclear Power plant 'Laguna Verde'. This last detector was also used to determine the neutron fluence in some points of interest, around and inside a low scattering neutron room at the 'Centro de Metrologia de Radiaciones Ionizantes' of the ININ, to know the background neutron field produced by the neutron sources used there. The design of the two neutron detector and the results obtained for each of the surveying facilities, are described in this work. (Author)

  15. Image processing technology for nuclear facilities

    Lee, Jong Min; Lee, Yong Beom; Kim, Woong Ki; Park, Soon Young

    1993-05-01

    Digital image processing technique is being actively studied since microprocessors and semiconductor memory devices have been developed in 1960's. Now image processing board for personal computer as well as image processing system for workstation is developed and widely applied to medical science, military, remote inspection, and nuclear industry. Image processing technology which provides computer system with vision ability not only recognizes nonobvious information but processes large information and therefore this technique is applied to various fields like remote measurement, object recognition and decision in adverse environment, and analysis of X-ray penetration image in nuclear facilities. In this report, various applications of image processing to nuclear facilities are examined, and image processing techniques are also analysed with the view of proposing the ideas for future applications. (Author)

  16. Gas processing at DOE nuclear facilities

    Jacox, J.

    1995-02-01

    The term {open_quotes}Gas Processing{close_quotes} has many possible meanings and understandings. In this paper, and panel, we will be using it to generally mean the treatment of gas by methods other than those common to HVAC and Nuclear Air Treatment. This is only a working guideline not a rigorous definition. Whether a rigorous definition is desirable, or even possible is a question for some other forum. Here we will be discussing the practical aspects of what {open_quotes}Gas Processing{close_quotes} includes and how existing Codes, Standards and industry experience can, and should, apply to DOE and NRC Licensed facilities. A major impediment to use of the best engineering and technology in many nuclear facilities is the administrative mandate that only systems and equipment that meet specified {open_quotes}nuclear{close_quotes} documents are permissible. This paper will highlight some of the limitations created by this approach.

  17. A systems approach to nuclear facility monitoring

    Argo, P.E.; Doak, J.E.; Howse, J.W.

    1996-01-01

    Sensor technology for use in nuclear facility monitoring has reached an advanced stage of development. Research on where to place these sensors in a facility and how to combine their outputs in a meaningful fashion does not appear to be keeping pace. In this paper, the authors take a global view of the problem where sensor technology is viewed as only one piece of a large puzzle. Other pieces of this puzzle include the optimal location and type of sensors used in a specific facility, the rate at which sensors record information, and the risk associated with the materials/processes at a facility. If the data are analyzed off-site, how will they be transmitted? Is real-time analysis necessary? Is one monitoring only the facility itself, or might one also monitor the processing that occurs there (e.g., tank levels and concentrations)? How is one going to combine the outputs from the various sensors to give us an accurate picture of the state of the facility? This paper will not try to answer all these questions, but rather it will attempt to stimulate thought in this area by formulating a systems approach to the problem demonstrated by a prototype system and a system proposed for an actual facility. The focus will be on the data analysis aspect of the problem. Future work in this area should focus on recommendations and guidelines for a monitoring system based upon the type of facility and processing that occurs there

  18. Tritium surveillance around nuclear facilities in Japan

    Inoue, Y.; Kasida, Y.

    1978-01-01

    In order to measure the tritium levels in the environmental water around the nuclear facilities, the tritium surveillance program began in 1967 locally at Tsuruga and Mihama districts. Nowadays it has been expanded to the ten commercial nuclear power stations and three nuclear facilities. For samples whose tritium concentration is believed less than about 100 pCi/l, they were electrolytically enriched, and then counted by the liquid scintillation counter. Some of samples believed higher than 100 pCi/l were analysed without any enrichment by the low background liquid scintillation counters, Aloka LB 600 or Aloka LB 1. The results of each station are listed in Table. The sampling points corresponding to each results are shown in Figure. Tritium from the effluent was not reflected in all the land water and the tap water around the nuclear power stations and the nuclear facilities. Tritium concentration in rivers, streams, and reservoirs (pools) decreased exponentially from about 600 pCi/l in 1967 to about 150 pCi/l in 1972 at Tsuruga and Mihama, and 360 pCi/l in 1968 to 120 pCi/l in 1973 at Genkai, with the half life of about 2.5 years in both cases. After around 1972, tritium levels of river system in all districts of Japan kept nearly constant up to the end of 1975 and they were in the range from 100 to 300 pCi/l corresponding to the districts. Thereafter, it seems to start to decrease again in 1976. Sea water sampled at the intake of the station or on the seashore far from the outlet was regarded not to be influenced by the effluent from the nuclear reactors or facilities. Tritium concentration in these coastal waters decreased from 100 - 300 pCi/l in 1971 to 30 - 40 pCi/l in 1972 in Fukushima, Ibaraki and Fukui prefectures. (author)

  19. Wheelchair cleaning and disinfection in Canadian health care facilities: "That's wheelie gross!".

    Gardner, Paula; Muller, Matthew P; Prior, Betty; So, Ken; Tooze, Jane; Eum, Linda; Kachur, Oksana

    2014-11-01

    Wheelchairs are complex equipment that come in close contact with individuals at increased risk of transmitting and acquiring antibiotic-resistant organisms and health care-associated infection. The purpose of this study was to determine the status of wheelchair cleaning and disinfection in Canadian health care facilities. Acute care hospitals (ACHs), chronic care hospitals (CCHs), and long-term care facilities (LTCFs) were contacted and the individual responsible for oversight of wheelchair cleaning and disinfection was identified. A structured interview was conducted that focused on current practices and concerns, barriers to effective wheelchair cleaning and disinfection, and potential solutions. Interviews were completed at 48 of the 54 facilities contacted (89%), including 18 ACHs, 16 CCHs, and 14 LTCFs. Most (n = 24) facilities had 50-200 in-house wheelchairs. Respondents were very concerned about wheelchair cleaning as an infection control issue. Specific concerns included the lack of reliable systems for tracking and identifying dirty and clean wheelchairs (71%, 34/48), failure to clean and disinfect wheelchairs between patients (52%, 25/48), difficulty cleaning cushions (42%, 20/48), lack of guidelines (35%, 27/48), continued use of visibly soiled wheelchairs (29%, 14/48) and lack of resources (25%, 12/48). Our results suggest that wheelchair cleaning and disinfection is not optimally performed at many Canadian hospitals and LTCFs. Specific guidance on wheelchair cleaning and disinfection is necessary. Copyright © 2014 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

  20. Proceedings of the 30. Annual Conference of the Canadian Nuclear Association

    Burroughs, P.

    1990-01-01

    The nineteen papers presented at this conference discuss the energy needs and challenges facing the Canadian nuclear industry, the environment and nuclear power, the problems of maintaining and developing industrial capacity, and the challenges of the 1990's. (L.L.)

  1. Microbial studies in the Canadian Nuclear Fuel Waste Management Program

    Stroes-Gascoyne, S.

    1996-01-01

    The management of the high level radioactive waste is an issue which generates Multifaceted conflicts. These conflicts are multi-determined, but are nonetheless, based on a myriad of associated concerns including but not exclusive to: effects of radiation on public health and safety, uncertainty associated with long-term assessments and effects, confidence in technology and in government and industry to protect public health and safety, and concerns regarding concurrent and intergenerational equity. These concerns are likely to be deeply felt by the many potential actors and stakeholders who will be impacted during the process of site selection for a nuclear waste disposal facility. Because this site selection is sure to be a controversial undertaking, it is in the interests of those who wish to promote the use of the high-level radioactive waste disposal concept, to understand fully the potential for conflict and consider alternative means of proactively preventing and/or resolving conflicts

  2. Security programs for Category I or II nuclear material or certain nuclear facilities. Regulatory guide G-274

    2003-03-01

    The purpose of this regulatory guide is to help applicants for a Canadian Nuclear Safety Commission (CNSC) licence in respect of Category I or II nuclear material - other than a licence to transport - , or a nuclear facility consisting of a nuclear reactor that may exceed 10 MW thermal power during normal operation, prepare and submit the security information to be included with the application, pursuant to the Nuclear Safety and Control Act (NSCA). Category I and II nuclear material are defined in Appendix B to this guide. This guide describes: the security information that should typically be included with the application for any licence referred to above; how the security information may be organized and presented in a separate document (hereinafter 'the security program description'), in order to assist CNSC review and processing of the application; and, the administrative procedures to be followed when preparing, submitting or revising the security program description. (author)

  3. Joint submission of the Canadian Nuclear Association and the Organization of CANDU Industries to the Ontario Nuclear Safety Review

    1987-08-01

    The manufacturing company members of the Canadian Nuclear Association and the Organization of CANDU Industries are proud to have played their part in the development of the peaceful application of nuclear technology in Ontario, and the achievement of the very real benefits discussed in this paper, which greatly outweigh the hypothetical risks

  4. Gas separation techniques in nuclear facilities

    Hioki, Hideaki; Morisue, Tetsuo; Ohno, Masayoshi

    1983-01-01

    The literatures concerning the gas separation techniques which are applied to the waste gases generated from nuclear power plants and nuclear fuel reprocessing plants, uranium enrichment and the instrumentation of nuclear facilities are reviewed. The gas permeability and gas separation performance of membranes are discussed in terms of rare gas separation. The investigation into the change of the gas permeability and mechanical properties of membranes with exposure to radiation is reported. The theoretical investigation of the separating cells used for the separation of rare gas and the development of various separating cells are described, and the theoretical and experimental investigations concerning rare gas separation using cascades are described. The application of membrane method to nuclear facilities is explained showing the examples of uranium enrichment, the treatment of waste gases from nuclear reactor buildings and nuclear fuel reprocessing plants, the monitoring of low level β-emitters in stacks, the detection of failed fuels and the detection of water leak in fast breeder reactors. (Yoshitake, I.)

  5. Pt. 1: Decommissioning of nuclear facilities. Pt. 2: Methods of decommissioning of nuclear facilities

    Steinkilberg, W.

    1982-01-01

    In the present paper the different steps of dismantlement of nuclear facilities are dealt with. First the planning principles for decomminconing are discussed and then the planning of the reactorblock dismantlement in the FR2 research reactor is described. (RW)

  6. The physical protection of nuclear material and nuclear facilities

    NONE

    1999-06-01

    The latest review (1993) of this document was of limited scope and resulted in changes to the text of INFCIRC/225/Rev.2 designed to make the categorization table in that document consistent with the categorization table contained in the Convention on Physical Protection of Nuclear Materials. Consequently, a comprehensive review of INFCIRC/225 has not been conducted since 1989. Consequently, a meeting of national experts was convened from 2-5 June 1998 and from 27-29 October 1998 for a thorough review of INFCIRC/225/Rev.3. The revised document reflects the recommendations of the national experts to improve the structure and clarity of the document and to take account of improved technology and current international and national practices. In particular, a chapter has been added which provides specific recommendations related to sabotage of nuclear facilities and nuclear material. As a result of this addition, the title has been changed to 'The Physical Protection of Nuclear Material and Nuclear Facilities'. The recommendations presented in this IAEA document reflect a broad consensus among Member States on the requirements which should be met by systems for the physical protection of nuclear materials and facilities. It is hoped that they will provide helpful guidance for Member States.

  7. The physical protection of nuclear material and nuclear facilities

    1999-06-01

    The latest review (1993) of this document was of limited scope and resulted in changes to the text of INFCIRC/225/Rev.2 designed to make the categorization table in that document consistent with the categorization table contained in the Convention on Physical Protection of Nuclear Materials. Consequently, a comprehensive review of INFCIRC/225 has not been conducted since 1989. Consequently, a meeting of national experts was convened from 2-5 June 1998 and from 27-29 October 1998 for a thorough review of INFCIRC/225/Rev.3. The revised document reflects the recommendations of the national experts to improve the structure and clarity of the document and to take account of improved technology and current international and national practices. In particular, a chapter has been added which provides specific recommendations related to sabotage of nuclear facilities and nuclear material. As a result of this addition, the title has been changed to 'The Physical Protection of Nuclear Material and Nuclear Facilities'. The recommendations presented in this IAEA document reflect a broad consensus among Member States on the requirements which should be met by systems for the physical protection of nuclear materials and facilities. It is hoped that they will provide helpful guidance for Member States

  8. Decommissioning of nuclear facilities using current criteria

    Shum, E.Y.; Swift, J.J.; Malaro, J.C.

    1991-01-01

    When a licensed nuclear facility ceases operation, the US Nuclear Regulatory Commission (NRC) is responsible for ensuring that the facility and its site are decontaminated to an acceptable level so that it is safe to release that facility and site for unrestricted public use. Currently, the NRC is developing decommissioning criteria based on reducing public doses from residual contamination in soils and structures at sites released for unrestricted use to as low as is reasonably achievable (ALARA). Plans are to quantify ALARA in terms of an annual total effective dose equivalent (TEDE) to an average member of the most highly exposed population group. The NRC is working on a regulatory guidance document to provide a technical basis for translating residual contamination levels to annual dose levels. Another regulatory guide is being developed to provide guidance to the licensee on how to conduct radiological surveys to demonstration compliance with the NRC decommissioning criteria. The methods and approaches used in these regulatory guides on the decommissioning of a nuclear facility are discussed in the paper

  9. Hematite nuclear fuel cycle facility decommissioning

    Hayes, K.

    2004-01-01

    Westinghouse Electric Company LLC ('Westinghouse') acquired a nuclear fuel processing plant at Hematite, Missouri ('Hematite', the 'Facility', or the 'Plant') in April 2000. The plant has subsequently been closed, and its operations have been relocated to a newer, larger facility. Westinghouse has announced plans to complete its clean-up, decommissioning, and license retirement in a safe, socially responsible, and environmentally sound manner as required by internal policies, as well as those of its parent company, British Nuclear Fuels plc. ('BNFL'). Preliminary investigations have revealed the presence of environmental contamination in various areas of the facility and grounds, including both radioactive contamination and various other substances related to the nuclear fuel processing operations. The disparity in regulatory requirements for radiological and nonradiological contaminants, the variety of historic and recent operations, and the number of previous owners working under various contractual arrangements for both governmental and private concerns has resulted in a complex project. This paper discusses Westinghouse's efforts to develop and implement a comprehensive decontamination and decommissioning (D and D) strategy for the facility and grounds. (author)

  10. International safeguards in large scale nuclear facilities

    Gupta, D.; Heil, J.

    1977-01-01

    The trend in the energy sector in most of the industrialized areas of the world shows rather clearly, that the rate of installation of nuclear plants will be very high and that the largest possible units of nuclear material handling and storage facilities will be built. Various experiments and analyses of measurement methods relevant to safeguards, in typical nuclear facilities like a fuel reprocessing or a fabrication plant, have shown that the associated measurement errors as obtained under normal operating conditions are such that they are mainly dominated by systematic errors and that such systematic errors may lie in the range of percentages of the measured amount so that a material balance in such a plant could not normally be closed with high accuracy. The simplest way of going around the problem would be to increase the frequency of striking a material balance over a given period of time. This could however lead to an anormous increase in the technical and financial burden for the operator of a facility. The present paper analyses this problem in some detail for some facilities and shows that with a properly developed information system in such plants and a combination of containment, surveillance and accountancy measures, safeguards statements for relatively low significant amounts can be made with the attainable range of measurement accuracies

  11. Iraq nuclear facility dismantlement and disposal project

    Cochran, J R; Danneels, J [Sandia National Laboratories, Albuquerque, NM (United States); Kenagy, W D [U.S. Department of State, Bureau of International Security and Nonproliferation, Office of Nuclear Energy, Safety and Security, Washington, DC (United States); Phillips, C J; Chesser, R K [Center for Environmental Radiation Studies, Texas Tech University, Lubbock, TX (United States)

    2007-07-01

    The Al Tuwaitha nuclear complex near Baghdad contains a significant number of nuclear facilities from Saddam Hussein's dictatorship. Because of past military operations, lack of upkeep and looting there is now an enormous radioactive waste problem at Al Tuwaitha. Al Tuwaitha contains uncharacterised radioactive wastes, yellow cake, sealed radioactive sources, and contaminated metals. The current security situation in Iraq hampers all aspects of radioactive waste management. Further, Iraq has never had a radioactive waste disposal facility, which means that ever increasing quantities of radioactive waste and material must be held in guarded storage. The Iraq Nuclear Facility Dismantlement and Disposal Program (the NDs Program) has been initiated by the U.S. Department of State (DOS) to assist the Government of Iraq (GOI) in eliminating the threats from poorly controlled radioactive materials, while building human capacities so that the GOI can manage other environmental cleanups in their country. The DOS has funded the International Atomic Energy Agency (IAEA) to provide technical assistance to the GOI via a Technical Cooperation Project. Program coordination will be provided by the DOS, consistent with U.S. and GOI policies, and Sandia National Laboratories will be responsible for coordination of participants and for providing waste management support. Texas Tech University will continue to provide in-country assistance, including radioactive waste characterization and the stand-up of the Iraq Nuclear Services Company. The GOI owns the problems in Iraq and will be responsible for the vast majority of the implementation of the NDs Program. (authors)

  12. A system approach to nuclear facility monitoring

    Argo, P.E.; Doak, J.E.; Howse, J.W.

    1996-09-01

    Sensor technology for use in nuclear facility monitoring has reached and advanced stage of development. Research on where to place these sensors in a facility and how to combine their outputs in a meaningful fashion does not appear to be keeping pace. In this paper, we take a global view of the problem where sensor technology is viewed as only one piece of a large puzzle. Other pieces of this puzzle include the optimal location and type of sensors used in a specific facility, the rate at which sensors record information, and the risk associated with the materials/processes at a facility. If the data are analyzed off-site, how will they be transmitted? Is real-time analysis necessary? Are we monitoring only the facility itself, or might we also monitor the processing that occurs there? How are we going to combine the output from the various sensors to give us an accurate picture of the state of the facility? This paper will not try to answer all these questions, but rather it will attempt to stimulate thought in this area by formulating a systems approach to the problem demonstrated by a prototype system and a systems proposed for an actual facility. Our focus will be on the data analysis aspect of the problem.

  13. Deactivating a major nuclear fuels reprocessing facility

    LeBaron, G.J.

    1997-01-01

    This paper describes three key processes used in deactivating the Plutonium Uranium Extraction (PUREX) Facility, a large, complex nuclear reprocessing facility, 15 months ahead of schedule and $77 million under budget. The organization was reengineered to refine its business processes and more effectively organize around the deactivation work scope. Multi-disciplined work teams were formed to be self-sufficient and empowered to make decisions and perform work. A number of benefits were realized by reengineering. A comprehensive process to develop end points which clearly identified specific results and the post-project facility configuration was developed so all areas of a facility were addressed. Clear and specific end points allowed teams to focus on completing deactivation activities and helped ensure there were no unfulfilled end-of-project expectations. The RCRA regulations require closure of permitted facilities within 180 days after cessation of operations which may essentially necessitate decommissioning. A more cost effective approach was adopted which significantly reduced risk to human health and the environment by taking the facility to a passive, safe, inexpensive-to-maintain surveillance and maintenance condition (deactivation) prior to disposition. PUREX thus became the first large reprocessing facility with active TSD [treatment, storage, and disposal] units to be deactivated under the RCRA regulations

  14. Testing lifting systems in nuclear facilities

    Kling, H.; Laug, R.

    1984-01-01

    Lifting systems in nuclear facilities must be inspected at regular intervals after having undergone their first acceptance test. These inspections are frequently carried out by service firms which not only employ the skilled personnel required for such jobs but also make available the necessary test equipment. The inspections in particular include a number of sophisticated load tests for which test load systems have been developed to allow lifting systems to be tested so that reactor specific boundary conditions are taken into account. In view of the large number of facilities to be inspected, the test load system is a modular system. (orig.) [de

  15. Nuclear fuel cycle facility accident analysis handbook

    Ayer, J.E.; Clark, A.T.; Loysen, P.; Ballinger, M.Y.; Mishima, J.; Owczarski, P.C.; Gregory, W.S.; Nichols, B.D.

    1988-05-01

    The Accident Analysis Handbook (AAH) covers four generic facilities: fuel manufacturing, fuel reprocessing, waste storage/solidification, and spent fuel storage; and six accident types: fire, explosion, tornado, criticality, spill, and equipment failure. These are the accident types considered to make major contributions to the radiological risk from accidents in nuclear fuel cycle facility operations. The AAH will enable the user to calculate source term releases from accident scenarios manually or by computer. A major feature of the AAH is development of accident sample problems to provide input to source term analysis methods and transport computer codes. Sample problems and illustrative examples for different accident types are included in the AAH

  16. Occupational radiation exposure in nuclear fuel cycle facilities

    1979-01-01

    ) determination of the trends in plant radiation fields, (2) control of the sources of radiation, e.g. through quality control of materials used in construction, (3) testing coolant purification techniques, (4) investigating the influence of coolant chemistry control, and (5) developing techniques for decontamination. The previously mentioned Canadian and Swedish experiences together with some significant Japanese results are being incorporated in these US research efforts. Radiation exposure experiences were described for fuel reprocessing plants in Belgium, Federal Republic of Germany, France and the United States using both direct and indirect maintenance. Exposures were similar to those received by nuclear power plant operators, maintenance and health physics personnel, all were well within international guidelines. The major part of the discussion centered around the following topics: the difficulties of applying cost/benefit analysis; the need for uniform reporting of exposure data; the necessity of preparing and designing for high-exposure maintenance activities; the desire for epidemiological studies on radiation workers which will include exposure; to other carcinogenic agents, smoking habits and medical and natural exposures; the reasons behind reported dose reductions. A great deal of practical experience is now available on minimizing industrial and collective doses to radiation workers, as well as on advanced techniques to control occupational exposure at nuclear fuel cycle facilities. (author)

  17. Nuclear training facilities at the Royal Naval College, Greenwich

    Head, J.L.; Lowther, C.A.; Marsh, J.R.W.

    1986-01-01

    The paper describes some of the nuclear training facilities at the Royal Naval College and the way the facilities are used in the training of personnel for the Naval nuclear propulsion programme. (author)

  18. The US nuclear science user facilities - 5276

    Kennedy, J.R.

    2015-01-01

    The primary mission of the NSUF (Nuclear Science User Facilities) is to provide access, at no cost to the researcher, to world-class, state-of-the art capabilities and expertise to advance nuclear science and technology through high impact research. Through the NSUF, nuclear energy researchers can access specialized and often unique and expensive equipment and facilities, as well as the accompanying expertise, including nuclear test reactors, ion beam accelerators, hot cell post-irradiation examination (PIE) equipment, synchrotron beam lines, and advanced radiologically qualified materials science PIE instrumentation. The NSUF can also support the design and fabrication of an irradiation experiment, the transport of that experiment to and from the reactor, the PIE activities, the analysis and interpretation of the data, and final material disposition. A special feature of the NSUF is its Sample Library of irradiated specimens made available to users that reduces investigation time and costs. Enhancing the Sample Library for future applications of advanced instrumentation and new ideas is a key goal of the NSUF. Similar to the effort on building a Sample Library, the NSUF is creating a searchable database of the infrastructure available to DOE-NE (Department Of Energy - Office of Nuclear Energy) supported researchers

  19. Nuclear power plant simulation facility evaluation methodology

    Haas, P.M.; Carter, R.J.; Laughery, K.R. Jr.

    1985-01-01

    A methodology for evaluation of nuclear power plant simulation facilities with regard to their acceptability for use in the US Nuclear Regulatory Commission (NRC) operator licensing exam is described. The evaluation is based primarily on simulator fidelity, but incorporates some aspects of direct operator/trainee performance measurement. The panel presentation and paper discuss data requirements, data collection, data analysis and criteria for conclusions regarding the fidelity evaluation, and summarize the proposed use of direct performance measurment. While field testing and refinement of the methodology are recommended, this initial effort provides a firm basis for NRC to fully develop the necessary methodology

  20. Management of tritium at nuclear facilities

    1984-01-01

    This report presents extending summaries of the works of the participants to an IAEA co-ordinated research programme, ''Handling Tritium - bearing effluents and wastes''. The subjects covered include production of tritium in nuclear power plants (mainly heavy water and light water reactors), as well as at reprocessing plants; removal and enrichment of tritium at nuclear facilities; conditioning methods and characteristics of immobilized tritium of low and high concentration; some potential methods of storage and disposal of tritium. In addition to the conclusions of this three-years work, possible activities in the field are recommended

  1. Case for one nuclear waste facility

    Colgate, S.A.

    1979-01-01

    There should be only one nuclear waste disposal facility, and that should be located adjacent to the Nevada Test Site where prior experience has demonstrated the relative impervious nature of bomb produced cavities. Federal dedication in perpetuity, security, management, experience, stratigraphy, and land values dictate the location. Proven natural mineral aqueous surface chemistry assures against radioactive migration. An additional level of assurance - stress engineering - a new technology, can be developed to mimic, far exceed, and then be applied retroactively, similar to the same phenomena occurring in underground nuclear explosions

  2. Performing a nuclear facility EMI audit

    White, D.R.J.

    1993-01-01

    This paper addresses several questions which may arise when performing a nuclear facility EMI audit. Among the issues addressed are how a nuclear electrical power plant can ensure that it has taken adequate EMC measures to protect it from hostile electromagnetic ambient environments, means by which these measures can be implemented with sufficient integrity and reliability, and how often an inspection or audit should be performed to assess the EMC measures. Means of assessing EMI hardening and effective control of aging effects are also discussed. 2 figs

  3. Nuclear facilities in the Federal Republic of Germany

    1991-01-01

    The information brochure is a survey of installed nuclear facilities in Germany, presenting on one page each a picture of a nuclear power plant together with the main relevant data, or of other type of nuclear facilities belonging to the nuclear fuel cycle (such as fuel production plant, fuel production plant, fuel element storage facilities, and facilities for spent fuel and waste management). (UA) [de

  4. Environmental radiation monitoring around the nuclear facilities

    Lee, Chang Woo; Choi, Geun Sik and others

    2001-02-01

    Environmental Radiation Monitoring was carried out with measurement of environment. Radiation and environmental radioactivity analysis around KAERI nuclear facilities and Seoul Research Reactor. The results of environmental radiation monitoring around KAERI nuclear facilities and Seoul Research Reactor are the follows : The average level of environmental radiation dose measured by NaI scintillation counter and accumulated radiation dose by TLD was almost same level compared with the past years. Gross {alpha}, {beta} radioactivity in environmental samples showed a environmental level. {gamma}-radionuclides in water samples were not detected. But only radionuclide K-40, which is natural radionuclide, was detected in the all samples and Cs-137 was detected in the surface soil and discharge sediment. The average level of environmental radiation dose around Seoul Research Reactor was almost same level compared with the past years, and Be-7 and Cs-137 were detected in some surface soil and discharge sediment by {gamma}-spectrometry.

  5. Environmental radiation monitoring around the nuclear facilities

    Lee, Chang Woo; Choi, Young Ho

    2000-02-01

    Environmental radiation monitoring was carried out with measurement of environment radiation and environmental radioactivity analysis around KAERI nuclear facilities and Seoul Research Reactor. The results of environmental radiation monitoring around KAERI nuclear facilities and Seoul Research Reactor are the follows: The average level of environmental radiation dose measured by NaI scintillation counter and accumulated radiation dose by TLD was almost some level compared with the past years. Gross α, β radioactivity in environmental samples showed a environmental level. γ-radionuclides in water sample were not detected. But only radionuclide K-40, which is natural radionuclide, was detected in the all samples and Cs-137 was detected in the surface soil and discharge sediment. The average level of environmental radiation dose around Seoul Research Reactor was almost same level compared with the past years, and Be-7 and Cs-137 were detected in some surface soil and discharge sediment by γ-spectrometry. (author)

  6. Industrial fans used in nuclear facilities

    Carlson, J.A.

    1987-01-01

    Industrial fans are widely used in nuclear facilities, and their most common use is in building ventilation. To control the spread of contamination, airflows are maintained at high levels. Therefore, the selection of the fan and fan control are important to the safety of people, equipment and the environment. As a result, 80% of all energy used in nuclear facilities is fan energy. Safety evolves from the durability, control and redundancy in the system. In new or retrofit installations, testing and qualification of fans and systems are completed prior to start-up. Less important but necessary is the energy conservation aspect of fan selection and installations. Fan efficiency, type of control and system installation are evaluated for energy use

  7. Environmental radiation monitoring around the nuclear facilities

    Lee, Chang Woo; Choi, Young Ho

    2000-02-01

    Environmental radiation monitoring was carried out with measurement of environment radiation and environmental radioactivity analysis around KAERI nuclear facilities and Seoul Research Reactor. The results of environmental radiation monitoring around KAERI nuclear facilities and Seoul Research Reactor are the follows: The average level of environmental radiation dose measured by NaI scintillation counter and accumulated radiation dose by TLD was almost some level compared with the past years. Gross {alpha}, {beta} radioactivity in environmental samples showed a environmental level. {gamma}-radionuclides in water sample were not detected. But only radionuclide K-40, which is natural radionuclide, was detected in the all samples and Cs-137 was detected in the surface soil and discharge sediment. The average level of environmental radiation dose around Seoul Research Reactor was almost same level compared with the past years, and Be-7 and Cs-137 were detected in some surface soil and discharge sediment by {gamma}-spectrometry. (author)

  8. Environmental radiation monitoring around the nuclear facilities

    Lee, Chang Woo; Choi, Young Ho; Lee, M.H. [and others

    1999-02-01

    Environmental radiation monitoring was carried out with measurement of environment radiation and environmental radioactivity analysis around KAERI nuclear facilities and Seoul research reactor. The results of environmental radiation monitoring around KAERI nuclear facilities and Seoul research reactor are the follows : The average level of environmental radiation dose measured by NaI scintillation counter and accumulated radiation dose by TLD was almost same level compared with the past years. Gross {alpha}, {beta} radioactivity in environmental samples showed a environmental level. {gamma}-radionuclides in water samples were not detected. But only radionuclide K-40, which is natural radionuclide, was detected in the all samples and Cs-137 was detected in the surface soil and discharge sediment. The average level of environmental radiation dose around Seoul research reactor was almost same level compared with the past years, and Be-7 and Cs-137 were detected in some surface soil and discharge sediment by {gamma}-spectrometry. (author). 3 refs., 50 tabs., 12 figs.

  9. Protection of nuclear facilities against outer aggressions

    Aussourd, P.; Candes, P.; Le Quinio, R.

    1976-01-01

    The various types of outer aggressions envisaged in safety analysis for nuclear facilities are reviewed. These outer aggressions are classified as natural and non-natural phenomena, the latter depending on the human activities in the vicinity of nuclear sites. The principal natural phenomena able to constitute aggressions are atmospheric phenomena (strong winds, snow storms, hail, frosting mists), hydrologie phenomena such as tides, surges, flood, low waters, and geologic phenomena such as earthquakes. Artificial phenomena are concerned with aircraft crashes, projectiles, fire, possible ruptures of dams, and intentional human aggressions. The protection against intentional human aggressions is of two sorts: first, the possibility of access to the installations mostly sensitive to sabotage are to be prevented or reduced, secondly redundant circuits and functions must be separated for preventing their simultaneous destruction in the case when sabotage actors have reach the core of the facility [fr

  10. Environmental radiation monitoring around the nuclear facilities

    Lee, Chang Woo; Choi, Geun Sik and others

    2001-02-01

    Environmental Radiation Monitoring was carried out with measurement of environment. Radiation and environmental radioactivity analysis around KAERI nuclear facilities and Seoul Research Reactor. The results of environmental radiation monitoring around KAERI nuclear facilities and Seoul Research Reactor are the follows : The average level of environmental radiation dose measured by NaI scintillation counter and accumulated radiation dose by TLD was almost same level compared with the past years. Gross α, β radioactivity in environmental samples showed a environmental level. γ-radionuclides in water samples were not detected. But only radionuclide K-40, which is natural radionuclide, was detected in the all samples and Cs-137 was detected in the surface soil and discharge sediment. The average level of environmental radiation dose around Seoul Research Reactor was almost same level compared with the past years, and Be-7 and Cs-137 were detected in some surface soil and discharge sediment by γ-spectrometry

  11. Proceedings of the 11th Annual Conference of the Canadian Nuclear Society

    Rouben, B.

    1990-01-01

    This volume contains the proceedings of the thirteen technical sessions at the 11. annual conference of the Canadian Nuclear Society. The 68 papers presented at this conference cover the areas of programmes and issues for the 90's; thermalhydraulics; reactor physics and fuel management; nuclear safety; small reactors; fuel behaviour; energy production and the environment; computer applications; nuclear systems; fusion; reactor decommissioning, irradiated fuel and materials handling; and reactor components, (L.L.)

  12. Air filters for use at nuclear facilities

    Linder, P [Aktiebolaget Atomenergi, Studsvik, Nykoeping (Sweden)

    1970-12-01

    The ventilation system of a nuclear facility plays a vital role in ensuring that the air in working areas and the environment remains free from radioactive contamination. An earlier IAEA publication, Techniques for Controlling Air Pollution from the Operation of Nuclear Facilities, Safety Series No. 17, deals with the design and operation of ventilation systems at nuclear facilities. These systems are usually provided with air-cleaning devices which remove the contaminants from the air. This publication is intended as a guide to those who are concerned with the design of air-filtering systems and with the testing, operation and maintenance of air-filter installations at nuclear facilities. Emphasis is mainly placed on so-called high-efficiency particulate air filters (HEPA filters) and on providing general information on them. Besides describing the usual filter types, their dimensions and construction materials, the guidebook attempts to explain their properties and behaviour under different operating conditions. It also gives advice on testing and handling the filters so that effective and safe performance is ensured. The guidebook should serve as an introduction to the use of high efficiency particulate air filters in countries where work with radioactive materials has only recently commenced. The list of references at the end of the book indicates sources of more advanced information for those who already have comprehensive experience in this field. It is assumed here that the filters are obtained from a manufacturer, and the guidebook thus contains no information on the design and development of the filter itself, nor does it deal with the cleaning of the intake air to a plant, with gas sorption or protective respiratory equipment.

  13. Computer codes for ventilation in nuclear facilities

    Mulcey, P.

    1987-01-01

    In this paper the authors present some computer codes, developed in the last years, for ventilation and radioprotection. These codes are used for safety analysis in the conception, exploitation and dismantlement of nuclear facilities. The authors present particularly: DACC1 code used for aerosol deposit in sampling circuit of radiation monitors; PIAF code used for modelization of complex ventilation system; CLIMAT 6 code used for optimization of air conditioning system [fr

  14. Air filters for use at nuclear facilities

    Linder, P.

    1970-01-01

    The ventilation system of a nuclear facility plays a vital role in ensuring that the air in working areas and the environment remains free from radioactive contamination. An earlier IAEA publication, Techniques for Controlling Air Pollution from the Operation of Nuclear Facilities, Safety Series No. 17, deals with the design and operation of ventilation systems at nuclear facilities. These systems are usually provided with air-cleaning devices which remove the contaminants from the air. This publication is intended as a guide to those who are concerned with the design of air-filtering systems and with the testing, operation and maintenance of air-filter installations at nuclear facilities. Emphasis is mainly placed on so-called high-efficiency particulate air filters (HEPA filters) and on providing general information on them. Besides describing the usual filter types, their dimensions and construction materials, the guidebook attempts to explain their properties and behaviour under different operating conditions. It also gives advice on testing and handling the filters so that effective and safe performance is ensured. The guidebook should serve as an introduction to the use of high efficiency particulate air filters in countries where work with radioactive materials has only recently commenced. The list of references at the end of the book indicates sources of more advanced information for those who already have comprehensive experience in this field. It is assumed here that the filters are obtained from a manufacturer, and the guidebook thus contains no information on the design and development of the filter itself, nor does it deal with the cleaning of the intake air to a plant, with gas sorption or protective respiratory equipment

  15. Cathodic protection of a nuclear fuel facility

    Corbett, R.A.

    1989-01-01

    This article discusses corrosion on buried process piping and tanks at a nuclear fuel facility and the steps taken to design a system to control underground corrosion. Collected data have indicated that cathodic protection is needed to supplement the regular use of high-integrity, corrosion-resistant coatings; wrapping systems; special backfills; and insulation material. The technical approach discussed in this article is generally applicable to other types of power and/or industrial plants with extensive networks of underground steel piping

  16. Decommissioning engineering systems for nuclear facilities and knowledge inheritance for decommissioning of nuclear facilities

    Tachibana, Mitsuo

    2016-01-01

    Information on construction, operation and maintenance of a nuclear facility is essential in order to plan and implement the decommissioning of the nuclear facility. A decommissioning engineering system collects these information efficiently, retrieves necessary information rapidly, and support to plan the reasonable decommissioning as well as the systematic implementation of dismantling activities. Then, knowledge of workers involved facility operation and dismantling activities is important because decommissioning of nuclear facility will be carried out for a long period. Knowledge inheritance for decommissioning has been carried out in various organizations. This report describes an outline of and experiences in applying decommissioning engineering systems in JAEA and activities related to knowledge inheritance for decommissioning in some organizations. (author)

  17. ERC Maintenance Implementation Plan for nuclear facilities

    Franquero, R.C.

    1997-05-01

    The inactive and surplus facilities assigned to the Environmental Restoration Contractor are shut down and have no operating production processes or production materials except for residual contamination. There is a minimal number of operating systems to support surveillance and maintenance or decontamination and decommissioning activities (D ampersand D). These systems may include heating and ventilation, air conditioning, lighting, and other electrical systems. Inactive and surplus facilities will be subject to periodic long-term surveillance to ensure the integrity of structures until D ampersand D. D ampersand D projects are of relatively short duration and end with all systems deactivated. Therefore, a rigorous in-depth maintenance program such as that required for producing nuclear facilities is not required or cost effective

  18. Vault submodel for the second interim assessment of the Canadian concept for nuclear fuel waste disposal

    LeNeveu, D.M.

    1986-02-01

    The consequences to man and the environment of the disposal of nuclear fuel waste are being studied within the Canadian Nuclear Fuel Waste Management Program. The concept being assessed is that of a sealed disposal vault at a depth of 1000 m in plutonic rock in the Canadian Shield. To determine the consequences, the vault and its environment are simulated using a SYstem Variability Analysis Code (SYVAC), a stochastic model of the disposal system. SYVAC contains three submodels that represent the three major parts of the disposal system: the vault, the geosphere and the biosphere. This report documents the conceptual and mathematical framework of the vault submodel

  19. Nuclear facility decommissioning and site remedial actions

    Knox, N.P.; Webb, J.R.; Ferguson, S.D.; Goins, L.F.; Owen, P.T.

    1990-09-01

    The 394 abstracted references on environmental restoration, nuclear facility decommissioning, uranium mill tailings management, and site remedial actions constitute the eleventh in a series of reports prepared annually for the US Department of Energy's Remedial Action Programs. Citations to foreign and domestic literature of all types -- technical reports, progress reports, journal articles, symposia proceedings, theses, books, patents, legislation, and research project descriptions -- have been included. The bibliography contains scientific, technical, economic, regulatory, and legal information pertinent to the US Department of Energy's Remedial Action Programs. Major sections are (1) Surplus Facilities Management Program, (2) Nuclear Facilities Decommissioning, (3) Formerly Utilized Sites Remedial Action Programs, (4) Facilities Contaminated with Naturally Occurring Radionuclides, (5) Uranium Mill Tailings Remedial Action Program, (6) Grand Junction Remedial Action Program, (7) Uranium Mill Tailings Management, (8) Technical Measurements Center, (9) Remedial Action Program, and (10) Environmental Restoration Program. Within these categories, references are arranged alphabetically by first author. Those references having no individual author are listed by corporate affiliation or by publication title. Indexes are provided for author, corporate affiliation, title word, publication description, geographic location, subject category, and keywords. This report is a product of the Remedial Action Program Information Center (RAPIC), which selects and analyzes information on remedial actions and relevant radioactive waste management technologies

  20. Nuclear facility decommissioning and site remedial actions

    Knox, N.P.; Webb, J.R.; Ferguson, S.D.; Goins, L.F.; Owen, P.T.

    1990-09-01

    The 394 abstracted references on environmental restoration, nuclear facility decommissioning, uranium mill tailings management, and site remedial actions constitute the eleventh in a series of reports prepared annually for the US Department of Energy's Remedial Action Programs. Citations to foreign and domestic literature of all types -- technical reports, progress reports, journal articles, symposia proceedings, theses, books, patents, legislation, and research project descriptions -- have been included. The bibliography contains scientific, technical, economic, regulatory, and legal information pertinent to the US Department of Energy's Remedial Action Programs. Major sections are (1) Surplus Facilities Management Program, (2) Nuclear Facilities Decommissioning, (3) Formerly Utilized Sites Remedial Action Programs, (4) Facilities Contaminated with Naturally Occurring Radionuclides, (5) Uranium Mill Tailings Remedial Action Program, (6) Grand Junction Remedial Action Program, (7) Uranium Mill Tailings Management, (8) Technical Measurements Center, (9) Remedial Action Program, and (10) Environmental Restoration Program. Within these categories, references are arranged alphabetically by first author. Those references having no individual author are listed by corporate affiliation or by publication title. Indexes are provided for author, corporate affiliation, title word, publication description, geographic location, subject category, and keywords. This report is a product of the Remedial Action Program Information Center (RAPIC), which selects and analyzes information on remedial actions and relevant radioactive waste management technologies.

  1. Nuclear facility decommissioning and site remedial actions

    Owen, P.T.; Knox, N.P.; Ferguson, S.D.; Fielden, J.M.; Schumann, P.L.

    1989-09-01

    The 576 abstracted references on nuclear facility decommissioning, uranium mill tailings management, and site remedial actions constitute the tenth in a series of reports prepared annually for the US Department of Energy's Remedial Action Programs. Citations to foreign and domestic literature of all types--technical reports, progress reports, journal articles, symposia proceedings, theses, books, patents, legislation, and research project descriptions--have been included. The bibliography contains scientific, technical, economic, regulatory, and legal information pertinent to the US Department of Energy's Remedial Action Programs. Major sections are (1) Surplus Facilities Management Program, (2) Nuclear Facilities Decommissioning, (3) Formerly Utilized Sites Remedial Action Program, (4) Facilities Contaminated with Naturally Occurring Radionuclides, (5) Uranium Mill Tailings Remedial Action Program, (6) Uranium Mill Tailings Management, (7) Technical Measurements Center, and (8) General Remedial Action Program Studies. Within these categories, references are arranged alphabetically by first author. Those references having no individual author are listed by corporate affiliation or by publication description. Indexes are provided for author, corporate affiliation, title work, publication description, geographic location, subject category, and keywords

  2. Nuclear facility decommissioning and site remedial actions

    Owen, P.T.; Knox, N.P.; Ferguson, S.D.; Fielden, J.M.; Schumann, P.L.

    1989-09-01

    The 576 abstracted references on nuclear facility decommissioning, uranium mill tailings management, and site remedial actions constitute the tenth in a series of reports prepared annually for the US Department of Energy's Remedial Action Programs. Citations to foreign and domestic literature of all types--technical reports, progress reports, journal articles, symposia proceedings, theses, books, patents, legislation, and research project descriptions--have been included. The bibliography contains scientific, technical, economic, regulatory, and legal information pertinent to the US Department of Energy's Remedial Action Programs. Major sections are (1) Surplus Facilities Management Program, (2) Nuclear Facilities Decommissioning, (3) Formerly Utilized Sites Remedial Action Program, (4) Facilities Contaminated with Naturally Occurring Radionuclides, (5) Uranium Mill Tailings Remedial Action Program, (6) Uranium Mill Tailings Management, (7) Technical Measurements Center, and (8) General Remedial Action Program Studies. Within these categories, references are arranged alphabetically by first author. Those references having no individual author are listed by corporate affiliation or by publication description. Indexes are provided for author, corporate affiliation, title work, publication description, geographic location, subject category, and keywords.

  3. Radioactive waste management from nuclear facilities

    2005-06-01

    This report has been published as a NSA (Nuclear Systems Association, Japan) commentary series, No. 13, and documents the present status on management of radioactive wastes produced from nuclear facilities in Japan and other countries as well. Risks for radiation accidents coming from radioactive waste disposal and storage together with risks for reactor accidents from nuclear power plants are now causing public anxiety. This commentary concerns among all high-level radioactive waste management from nuclear fuel cycle facilities, with including radioactive wastes from research institutes or hospitals. Also included is wastes produced from reactor decommissioning. For low-level radioactive wastes, the wastes is reduced in volume, solidified, and removed to the sites of storage depending on their radioactivities. For high-level radioactive wastes, some ten thousand years must be necessary before the radioactivity decays to the natural level and protection against seismic or volcanic activities, and terrorist attacks is unavoidable for final disposals. This inevitably results in underground disposal at least 300 m below the ground. Various proposals for the disposal and management for this and their evaluation techniques are described in the present document. (S. Ohno)

  4. Improvement of management systems for nuclear facilities

    2005-01-01

    The area of Quality Management/ Quality Assurance has been changed dramatically over the past years. The nuclear facilities moved from the 'traditional' Quality Assurance approach towards Quality Management Systems, and later a new concept of Integrated Management Systems was introduced. The IAEA is developing a new set of Standards on Integrated Management Systems, which will replace the current 50-C-Q/SG-Q1-Q14 Code. The new set of document will require the integration of all management areas into one coherent management system. The new set of standards on Management Systems promotes the concept of the Integrated Management Systems. Based on new set a big number of documents are under preparation. These documents will address the current issues in the management systems area, e.g. Management of Change, Continuous Improvement, Self-assessment, and Attributes of effective management, etc. Currently NPES is providing a number of TC projects and Extra Budgetary Programmes to assist Member States in this area. The new Standards on Management Systems will be published in 2006. A number of Regulatory bodies already indicated that they would take the new Management System Standards as a basis for the national regulation. This fact will motivate a considerable change in the management of nuclear utilities, requiring a new approach. This activity is suitable for all IAEA Members States with large or limited nuclear capabilities. The service is directed to provide assistance for the management of all organizations carrying on or regulating nuclear activities and facilities

  5. Emergency planning and preparedness for nuclear facilities

    1986-01-01

    In order to review the advances made over the past seven years in the area of emergency planning and preparedness supporting nuclear facilities and consider developments which are on the horizon, the IAEA at the invitation of the Government of Italy, organized this International Symposium in co-operation with the Italian Commission for Nuclear and Alternative Energy Sources, Directorate of Nuclear Safety and Health Protection (ENEA-DISP). There were over 250 designated participants and some 70 observers from 37 Member States and four international organizations in attendance at the Symposium. The Symposium presentations were divided into sessions devoted to the following topics: emergency planning (20 papers), accident assessment (30 papers), protective measures and recovery operations (10 papers) and emergency preparedness (16 papers). A separate abstract was prepared for each of these papers

  6. Russian Federal nuclear center facilities for nuclear spectroscopy investigations

    Ilkaev, R.I.; Punin, V.T.; Abramovich, S.N.

    2001-01-01

    Russian Federal Nuclear Center facilities for Spectroscopy investigation in the field of nuclear spectroscopy are described. Here are discussed basic properties of used radiation sources, facilities and technologies for target material production and manufacture of targets from rare, high-toxic or radioactive materials. Here are also reported basic features of complex detector systems and technologies for manufacture of scintillation detectors with special properties VNIIEF was founded as a weapons laboratory. The development of nuclear and thermonuclear bombs was followed by a wide complex of nuclear-physics investigations. Naturally, data on nuclear-physics properties of active and structure materials being part of nuclear weapons were of greatest interest.At the initial stage of work on the development of nuclear weapons the information on nuclear constants of materials including the most important neutron ones was rather scant. Data published in scientific literature had low exactness and were insecure. Results of measurements sometimes differed greatly by various groups of investigators. At the same time it was clear that, for example, a 1,5-times mistake in the fission cross-section could cause a several times mistake in the choice of uranium or plutonium mass, which is necessary for the bomb development. These circumstances determined importance of the nuclear-physics investigations. Demands on knowledge of process details occurring inside the nuclei conditioned by a problem of developing and improving of nuclear weapons and atomic power are rather limited. However, the further development of nuclear industry has proved a well-known point that this knowledge being accumulated forms a critical mass that leads to an explosive situation in the elaboration both of ideological and technological aspects of these problems. It is the tendency of inside development of nuclear science that has conditioned preparedness of knowledge about intranuclear processes for

  7. New nuclear facilities and their analytical applications in China

    Zhang, Z.Y.; He, X.; Ma, Y.H.; Ding, Y.Y.; Chai, Z.F.

    2014-01-01

    Nuclear analytical techniques are a family of modern analytical methods that are based on nuclear reactions, nuclear effects, nuclear radiations, nuclear spectroscopy, nuclear parameters, and nuclear facilities. Because of their combined characteristics of sensitivity and selectivity, they are widely used in projects ranging from life sciences to deep-space exploration. In this review article, new nuclear facilities and their analytical applications in China are selectively reviewed, covering the following aspects: large scientific facilities, national demands, and key scientific issues with the emphasis on the new achievements. (orig.)

  8. Epidemiological studies of radiation workers in nuclear facilities

    Iwai, Satoshi; Semba, Tsuyoshi; Ishida, Kenji; Takagi, Syunji; Igari, Takafumi

    2017-01-01

    Regarding workers at nuclear facilities, this paper described INWORKS epidemiological research published in 2015, cooperative cohort epidemiological research of IARC 15 countries 10 years before that (15-country study), and the flow of radiation epidemiological research in the period from 15-country study to INWORKS. INWORKS is a retrospective cohort study to investigate the correlation between mortality due to solid cancer, blood cancer, and cardiovascular diseases in workers in three countries of France / the U.K. / the U.S. and low dose exposure through long-term photon external exposure. It obtained the data showing the statistical significance of increased cancer death rate. However, from the subjects of the analysis, no significant evaluation was made on neutron exposure and internal exposure. Statistically significant cancer mortality was confirmed in 15-country study at low dose, low dose rate, and prolonged exposure, but significant cancer mortality rate could not be confirmed excluding Canadian data, which had problems in dose evaluation. In the epidemiological studies of cancer mortality rates of radiation workers in nuclear power industries performed in France / the U.K. / the U.S. in the period ranging from 15-country study to INWORKS, significant difference was not recognized between cancer death rate and excessive relative risk (ERR) compared with LSS epidemiological research studies that handled acute exposure. Several tasks are still remaining. (A.O.)

  9. Financing Strategies for Nuclear Fuel Cycle Facility

    David Shropshire; Sharon Chandler

    2005-01-01

    To help meet our nation's energy needs, reprocessing of spent nuclear fuel is being considered more and more as a necessary step in a future nuclear fuel cycle, but incorporating this step into the fuel cycle will require considerable investment. This report presents an evaluation of financing scenarios for reprocessing facilities integrated into the nuclear fuel cycle. A range of options, from fully government owned to fully private owned, was evaluated using a DPL (Dynamic Programming Language) 6.0 model, which can systematically optimize outcomes based on user-defined criteria (e.g., lowest life-cycle cost, lowest unit cost). Though all business decisions follow similar logic with regard to financing, reprocessing facilities are an exception due to the range of financing options available. The evaluation concludes that lowest unit costs and lifetime costs follow a fully government-owned financing strategy, due to government forgiveness of debt as sunk costs. Other financing arrangements, however, including regulated utility ownership and a hybrid ownership scheme, led to acceptable costs, below the Nuclear Energy Agency published estimates. Overwhelmingly, uncertainty in annual capacity led to the greatest fluctuations in unit costs necessary for recovery of operating and capital expenditures; the ability to determine annual capacity will be a driving factor in setting unit costs. For private ventures, the costs of capital, especially equity interest rates, dominate the balance sheet; the annual operating costs dominate the government case. It is concluded that to finance the construction and operation of such a facility without government ownership could be feasible with measures taken to mitigate risk, and that factors besides unit costs should be considered (e.g., legal issues, social effects, proliferation concerns) before making a decision on financing strategy

  10. ICT security- aspects important for nuclear facilities

    Thunem, Atoosa P-J.

    2005-09-01

    Rapid application growth of complex Information and Communication Technologies (ICT) in every society and state infrastructure as well as industry has revealed vulnerabilities that eventually have given rise to serious security breaches. These vulnerabilities together with the course of the breaches from cause to consequence are gradually about to convince the field experts that ensuring the security of ICT-driven systems is no longer possible by only relying on the fundaments of computer science, IT, or telecommunications. Appropriating knowledge from other disciplines is not only beneficial, but indeed very necessary. At the same time, it is a common observation today that ICT-driven systems are used everywhere, from the nuclear, aviation, commerce and healthcare domains to camera-equipped web-enabled cellular phones. The increasing interdisciplinary and inter-sectoral aspects of ICT security worldwide have been providing updated and useful information to the nuclear domain, as one of the emerging users of ICT-driven systems. Nevertheless, such aspects have also contributed to new and complicated challenges, as ICT security for the nuclear domain is in a much more delicate manner than for any other domains related to the concept of safety, at least from the public standpoint. This report addresses some important aspects of ICT security that need to be considered at nuclear facilities. It deals with ICT security and the relationship between security and safety from a rather different perspective than usually observed and applied. The report especially highlights the influence on the security of ICT-driven systems by all other dependability factors, and on that basis suggests a framework for ICT security profiling, where several security profiles are assumed to be valid and used in parallel for each ICT-driven system, sub-system or unit at nuclear facilities. The report also covers a related research topic of the Halden Project with focus on cyber threats and

  11. No nuclear power. No disposal facility?

    Feinhals, J. [DMT GmbH und Co.KG, Hamburg (Germany)

    2016-07-01

    Countries with a nuclear power programme are making strong efforts to guarantee the safe disposal of radioactive waste. The solutions in those countries are large disposal facilities near surface or in deep geological layers depending on the activity and half-life of the nuclides in the waste. But what will happen with the radioactive waste in countries that do not have NPPs but have only low amounts of radioactive waste from medical, industrial and research facilities as well as from research reactors? Countries producing only low amounts of radioactive waste need convincing solutions for the safe and affordable disposal of their radioactive waste. As they do not have a fund by an operator of nuclear power plants, those countries need an appropriate and commensurate solution for the disposal of their waste. In a first overview five solutions seem to be appropriate: (i) the development of multinational disposal facilities by using the existing international knowhow; (ii) common disposal with hazardous waste; (iii) permanent storage; (iv) use of an existing mine or tunnel; (v) extension of the borehole disposal concept for all the categories of radioactive wastes.

  12. Financing the Decommissioning of Nuclear Facilities

    2016-01-01

    Decommissioning of both commercial and R and D nuclear facilities is expected to increase significantly in the coming years, and the largest of such industrial decommissioning projects could command considerable budgets. It is important to understand the costs of decommissioning projects in order to develop realistic cost estimates as early as possible based on preliminary decommissioning plans, but also to develop funding mechanisms to ensure that future decommissioning expenses can be adequately covered. Sound financial provisions need to be accumulated early on to reduce the potential risk for residual, unfunded liabilities and the burden on future generations, while ensuring environmental protection. Decommissioning planning can be subject to considerable uncertainties, particularly in relation to potential changes in financial markets, in energy policies or in the conditions and requirements for decommissioning individual nuclear installations, and such uncertainties need to be reflected in regularly updated cost estimates. This booklet offers a useful overview of the relevant aspects of financing the decommissioning of nuclear facilities. It provides information on cost estimation for decommissioning, as well as details about funding mechanisms and the management of funds based on current practice in NEA member countries. (authors)

  13. Unlocking the atom : the Canadian book on nuclear technology

    Tammemagi, H.; Jackson, D.

    2002-01-01

    This book describes Canada's role in developing a world-class reactor, medical isotope and food irradiation systems and it's leading role in uranium mining. It gives an introduction to both natural and man-made radiation and covers the spectrum of nuclear technology that includes power reactors, nuclear safety, nuclear waste, medicine, uranium, fusion, industrial and research applications. The second chapter in this book introduces the reader to nuclear fission, the fission reactor, nuclear weapons and the Candu Nuclear Power Reactor. The third chapter familiarizes the reader with different types of natural and man-made radiations. The fourth chapter discusses the biological effects of radiation. Electricity and the different technologies to produce electrical power are the subject of chapter five. The Candu reactor and the various Candu designs and performance are discussed in some detail in chapter six. In chapter seven the authors discuss the different types of reactors that have been constructed worldwide. Nuclear safety and nuclear regulations are the subject of chapter eight. In chapter nine the authors discuss nuclear power and the environment. High-level nuclear waste and nuclear waste disposal are discussed in chapter ten. Diagnostic and therapeutic nuclear medicine is the subject of chapter eleven. The benefits of nuclear technology in industry and science are discussed in chapter twelve. Uranium mining and uranium as the nuclear fuel are discussed in chapter thirteen. Chapter fourteen discusses the future of fission with respect to advanced Candu fuel cycles and advanced Candu reactor designs. Chapter fifteen is a discussion of nuclear fusion and Canada's role in fusion research. Chapter sixteen discusses nuclear science and research and the role of the National nuclear laboratory and the universities

  14. Guide to the Canadian nuclear fuel waste management program. 2.ed

    Rosinger, E.L.J.; Lyon, R.B.; Gillespie, P.; Tamm, J.

    1983-02-01

    This document describes the administrative structure and major research and development components of the Canadian Nuclear Fuel Waste Management Program. It outlines the participating organizations, summarizes the program statistics, and describes the international cooperation and external review aspects of the program

  15. Proceedings of the 13. annual conference of the Canadian Nuclear Society. V. 1

    1993-12-31

    Volume 1 of the proceedings of the 13. annual conference of the Canadian Nuclear Society includes sessions on the following topics: reactor physics, new concepts and technology, fuel behaviour, reactor design, safety analysis, fuel channel behaviour, equipment and design qualification. The individual papers have been abstracted separately.

  16. An overview of heat exchanger technology in the Canadian nuclear program

    Carlucci, L.N.; Dalrymple, D.G.; Ko, P.L.; Pathania, R.; Pettigrew, M.I.; Scott, D.A.

    1981-06-01

    This paper provides an overview of the Canadian approach to the reliability and serviceability of heat exchange equipment used in nuclear power stations and heavy water plants. Current work in vibration and fretting predictions, thermal-hydraulic analyses, and corrosion research is described. Procedures developed for in-service inspection, in situ tube replacment and chemical cleaning of corrosion products are also outlined

  17. Research Facilities for the Future of Nuclear Energy

    Ait Abderrahim, H.

    1996-01-01

    The proceedings of the ENS Class 1 Topical Meeting on Research facilities for the Future of Nuclear Energy include contributions on large research facilities, designed for tests in the field of nuclear energy production. In particular, issues related to facilities supporting research and development programmes in connection to the operation of nuclear power plants as well as the development of new concepts in material testing, nuclear data measurement, code validation, fuel cycle, reprocessing, and waste disposal are discussed. The proceedings contain 63 papers

  18. High-risk facilities. Emergency management in nuclear, chemical and hazardous waste facilities

    Kloepfer, Michael

    2012-01-01

    The book on emergency management in high-risk facilities covers the following topics: Change in the nuclear policy, risk management of high-risk facilities as a constitutional problem - emergency management in nuclear facilities, operational mechanisms of risk control in nuclear facilities, regulatory surveillance responsibilities for nuclear facilities, operational mechanism of the risk control in chemical plants, regulatory surveillance responsibilities for chemical facilities, operational mechanisms of the risk control in hazardous waste facilities, regulatory surveillance responsibilities for hazardous waste facilities, civil law consequences in case of accidents in high-risk facilities, criminal prosecution in case of accidents in high-risk facilities, safety margins as site risk for emission protection facilities, national emergency management - strategic emergency management structures, warning and self-protection of the public in case of CBRN hazards including aspects of the psych-social emergency management.

  19. Emergency facility control device for nuclear reactor

    Ikehara, Morihiko.

    1981-01-01

    Purpose: To increase the reliability of a nuclear reactor by allowing an emergency facility to be manually started and stopped to make its operation more convenient and eliminate the possibility of erroneous operation in an emergency. Constitution: There are provided a first water level detector for detecting a level lower than the first low water level in a reactor container and a second water level detector for detecting a level lower than the second low water level lower than the first low water level, and an emergency facility can be started and stopped manually only when the level is higher than the second low water level, but the facility will be started regardless of the state of the manual operation when the level is lower than the second low water level. Thus, the emergency facility can be started by manual operation, but will be automatically started so as to secure the necessary minimum operation if the level becomes lower than the second low water level and the stopping operation thereafter is forgotten. (Kamimura, M.)

  20. Proceedings of the Canadian Nuclear Society ninth annual conference, 1988

    1988-01-01

    The 74 papers presented at this conference covered the following topics: operational enhancements of existing nuclear power plants; design of small reactors; accident behaviour in CANDU reactor fuel channels; fuel storage and waste management; reactor commissioning and decommissioning; nuclear safety experiments and modelling; the next generation of CANDU reactors; advances in nuclear engineering education in Canada; safety of small reactors; current position and improvements of fuel channels; current issues in nuclear safety; and, medical and industrial radiation applications

  1. Storage facilities of spent nuclear fuel in dry for Mexican nuclear facilities

    Salmeron V, J. A.; Camargo C, R.; Nunez C, A.; Mendoza F, J. E.; Sanchez J, J.

    2013-10-01

    In this article the relevant aspects of the spent fuel storage and the questions that should be taken in consideration for the possible future facilities of this type in the country are approached. A brief description is proposed about the characteristics of the storage systems in dry, the incorporate regulations to the present Nuclear Regulator Standard, the planning process of an installation, besides the approaches considered once resolved the use of these systems; as the modifications to the system, the authorization periods for the storage, the type of materials to store and the consequent environmental impact to their installation. At the present time the Comision Nacional de Seguridad Nuclear y Salvaguardias (CNSNS) considers the possible generation of two authorization types for these facilities: Specific, directed to establish a new nuclear installation with the authorization of receiving, to transfer and to possess spent fuel and other materials for their storage; and General, focused to those holders that have an operation license of a reactor that allows them the storage of the nuclear fuel and other materials that they possess. Both authorizations should be valued according to the necessities that are presented. In general, this installation type represents a viable solution for the administration of the spent fuel and other materials that require of a temporary solution previous to its final disposal. Its use in the nuclear industry has been increased in the last years demonstrating to be appropriate and feasible without having a significant impact to the health, public safety and the environment. Mexico has two main nuclear facilities, the nuclear power plant of Laguna Verde of the Comision Federal de Electricidad (CFE) and the facilities of the TRIGA Reactor of the Instituto Nacional de Investigaciones Nucleares (ININ) that will require in a future to use this type of disposition installation of the spent fuel and generated wastes. (Author)

  2. Decontamination Technology Development for Nuclear Research Facilities

    Oh, Won Zin; Jung, Chong Hun; Choi, Wang Kyu; Won, Hui Jun; Kim, Gye Nam

    2004-02-01

    Technology development of surface decontamination in the uranium conversion facility before decommissioning, technology development of component decontamination in the uranium conversion facility after decommissioning, uranium sludge treatment technology development, radioactive waste soil decontamination technology development at the aim of the temporary storage soil of KAERI, Optimum fixation methodology derivation on the soil and uranium waste, and safety assessment methodology development of self disposal of the soil and uranium waste after decontamination have been performed in this study. The unique decontamination technology applicable to the component of the nuclear facility at room temperature was developed. Low concentration chemical decontamination technology which is very powerful so as to decrease the radioactivity of specimen surface under the self disposal level was developed. The component decontamination technology applicable to the nuclear facility after decommissioning by neutral salt electro-polishing was also developed. The volume of the sludge waste could be decreased over 80% by the sludge waste separation method by water. The electrosorption method on selective removal of U(VI) to 1 ppm of unrestricted release level using the uranium-containing lagoon sludge waste was tested and identified. Soil decontamination process and equipment which can reduce the soil volume over 90% were developed. A pilot size of soil decontamination equipment which will be used to development of real scale soil decontamination equipment was designed, fabricated and demonstrated. Optimized fixation methodology on soil and uranium sludge was derived from tests and evaluation of the results. Safety scenario and safety evaluation model were development on soil and uranium sludge aiming at self disposal after decontamination

  3. Human factors methods in DOE nuclear facilities

    Bennett, C.T.; Banks, W.W.; Waters, R.J.

    1993-01-01

    The US Department of Energy (DOE) is in the process of developing a series of guidelines for the use of human factors standards, procedures, and methods to be used in nuclear facilities. This paper discusses the philosophy and process being used to develop a DOE human factors methods handbook to be used during the design cycle. The following sections will discuss: (1) basic justification for the project; (2) human factors design objectives and goals; and (3) role of human factors engineering (HFE) in the design cycle

  4. Guidance for air sampling at nuclear facilities

    Breslin, A.J.

    1976-11-01

    The principal uses of air sampling at nuclear facilities are to monitor general levels of radioactive air contamination, identify sources of air contamination, and evaluate the effectiveness of contaminant control equipment, determine exposures of individual workers, and provide automatic warning of hazardous concentrations of radioactivity. These applications of air sampling are discussed with respect to standards of occupational exposure, instrumentation, sample analysis, sampling protocol, and statistical treatment of concentration data. Emphasis is given to the influence of spacial and temporal variations of radionuclide concentration on the location, duration, and frequency of air sampling

  5. Evaluation of Nuclear Facility Decommissioning Projects program

    Baumann, B.L.

    1983-01-01

    The objective of the Evaluation of Nuclear Facility Decommissioning Projects (ENFDP) program is to provide the NRC licensing staff with data which will allow an assessment of radiation exposure during decommissioning and the implementation of ALARA techniques. The data will also provide information to determine the funding level necessary to ensure timely and safe decommissioning operations. Actual decommissioning costs, methods and radiation exposures are compared with those estimated by the Battelle-PNL and ORNL NUREGs on decommissioning. Exposure reduction techniques applied to decommissioning activities to meet ALARA objectives are described. The lessons learned concerning various decommissioning methods are evaluated

  6. Innovative ways of decontaminating nuclear facilities

    Bremmer, Jan; Gentes, Sascha; Ambos, Frank

    2009-01-01

    The great variety of surfaces to be decontaminated in a nuclear power plant increases demand for economic solutions and efficient processing systems. The Institute for Technology and Management in Building (TMB) of the University of Karlsruhe (TH) is working on this task in the new professorship of Sascha Gentes and, together with sat Kerntechnik GmbH, developing innovative techniques and tools for surface decontamination. In this effort, sat.Kerntechnik GmbH contributes 50% to the funding of the new professorship at the Karlsruhe Institute of Technology, the merger of the University of Karlsruhe and the Karlsruhe Research Center. The new professorship will extend its work also to various other innovative concepts to be employed not only in demolition but also in maintenance and operation of nuclear facilities. Above and beyond theoretical approaches, practical solutions are in the focus of work. For this reason, new developments are elaborated in close cooperation with the respective users. (orig.)

  7. Environmental radiation monitoring around the nuclear facilities

    Lee, Chang Woo

    2012-03-15

    Environmental Radiation Monitoring was carried out with measurement of environment. radiation and environmental radioactivity analysis on the sites of KAERI nuclear facilities and Seoul Research Reactors and their environments. The average level of environmental radiation dose measured by an ERM and the accumulated radiation dose by a TLD were almost same level compared with the previous years. The activity of gross {alpha} and gross {beta}, Tritium, Uranium and Strontium in environmental samples showed a environmental level. The {gamma}-radionuclides such as natural radionuclides 40K or 7Be were detected in pine needle and food. The nuclear radionuclides 134Cs, 137Cs or 131I were temporarily detected in the samples of air particulate and rain in April and of fall out in 2nd quarter from the effect of Fukusima accident.

  8. Robotic inspection of nuclear waste storage facilities

    Fulbright, R.; Stephens, L.M.

    1995-01-01

    The University of South Carolina and the Westinghouse Savannah River Company have developed a prototype mobile robot designed to perform autonomous inspection of nuclear waste storage facilities. The Stored Waste Autonomous Mobile Inspector (SWAMI) navigates and inspects rows of nuclear waste storage drums, in isles as narrow as 34 inches with drums stacked three high on each side. SWAMI reads drum barcodes, captures drum images, and monitors floor-level radiation levels. The topics covered in this article reporting on SWAMI include the following: overall system design; typical mission scenario; barcode reader subsystem; video subsystem; radiation monitoring subsystem; position determination subsystem; onboard control system hardware; software development environment; GENISAS, a C++ library; MOSAS, an automatic code generating tool. 10 figs

  9. Decommissioning and deactivation of nuclear facilities

    Anasco, Roberto; Harriague, Santiago; Hey, Alfredo M.; Fabbri, Silvio; Garonis, Omar H.

    2003-01-01

    The National Atomic Energy Commission (CNEA) is responsible for the decommissioning and deactivation of all relevant nuclear facilities in Argentina. A D and D Subprogram was created in 2000, within Technology Branch of the CNEA, in order to fulfill this responsibility. The D and D Subprogram has organized its activities in four fields: Planning; Technology development; Human resources development and training; International cooperation. The paper describes the work already done in those 4 areas, as well as the nuclear facilities existing in the country. Planning is being developed for the decommissioning of research reactors, beginning with RA-1, as well as for the Atucha I nuclear power station. An integral Management System has been developed, compatibilizing requirements from ISO 9001, ISO 14001, the national norm for Safety and Occupational Health (equivalent to BS 8800), and IAEA 50-SG Q series. Technology development is for the time being concentrated on mechanical decontamination and concrete demolition. A review has been made of technologies already developed both by CNEA and Nucleoelectrica Argentina S.A. (the nuclear power utility) in areas of chemical and electrochemical decontamination, cutting techniques and robotics. Human resources development has been based on training abroad in the areas of decontamination, cutting techniques, quality assurance and planning, as well as on specific courses, seminars and workshops. An IAEA regional training course on D and D has been given on April 2002 at CNEA's Constituyentes Atomic Center, with the assistance of 22 university graduates from 13 countries in the Latin American and Caribbean Region, and 11 from Argentina. CNEA has also given fellowships for PhD and Master thesis on the subject. International cooperation has been intense, and based on: - IAEA Technical Cooperation Project and experts missions; - Cooperation agreement with the US Department of Energy; - Cooperation agreement with Germany

  10. Waste management practices in decommissioning nuclear facilities

    Dickson, H.W.

    1979-01-01

    Several thousand sites exist in the United States where nuclear activities have been conducted over the past 30 to 40 years. Questions regarding potential public health hazards due to residual radioactivity and radiation fields at abandoned and inactive sites have prompted careful ongoing review of these sites by federal agencies including the Department of Energy (DOE) and the Nuclear Regulatory Commission (NRC). In some instances, these reviews are serving to point out poor low-level waste management practices of the past. Many of the sites in question lack adequate documentation on the radiological conditions at the time of release for unrestricted use or were released without appropriate restrictions. Recent investigations have identified residual contamination and radiation levels on some sites which exceed present-day standards and guidelines. The NRC, DOE, and Environmental Protection Agency are all involved in developing decontamination and decommissioning (D and D) procedures and guidelines which will assure that nuclear facilities are decommissioned in a manner that will be acceptable to the nuclear industry, various regulatory agencies, other stakeholders, and the general public

  11. Radiological dose assessment from the operation of Daeduk nuclear facilities

    Hwang, Won Tae; Kim, Eun Han; Suh, Kyung Suk; Choi, Young Gil [Korea Atomic Energy Research Institute, Taejon (Korea)

    2000-02-01

    The objective of this project is to assure the public acceptance for nuclear facilities, and the environmental safety from the operation of Daeduk nuclear facilities, such as HANARO research reactor, nuclear fuel processing facilities and others. For identifying the integrity of their facilities, the maximum individual doses at the site boundary and on the areas with high population density were assessed. Also, the collective doses within radius 80 km from the site were assessed. The radiation impacts for residents around the site from the operation of Daeduk nuclear facilities in 1999 were neglectable. 8 refs., 10 figs., 27 tabs. (Author)

  12. The role of economic incentives in nuclear waste facility siting

    Davis, E.M.

    1986-01-01

    There is a need to provide some public benefit and/or reward for accepting a ''locally unwanted land use'' (LULU) facility such as a nuclear waste storage or disposal facility. This paper concludes that DOE, Congress and the states should immediately quantify an economic incentive for consideration ''up front'' by society on siting decisions for nuclear waste storage and disposal facilities

  13. Creation of a new-generation research nuclear facility

    Girchenko, A.A.; Matyushin, A.P.; Kudryavtsev, E.M.; Skopin, V.P.; Shchepelev, R.M.

    2013-01-01

    The SO-2M research nuclear facility operated on the industrial area of the institute. The facility is now removed from service. In view of this circumstance, it is proposed to restore the facility at the new qualitative level, i.e., to create a new-generation research nuclear facility with a very high safety level consisting of a subcritical bench and a proton accelerator (electronuclear facility). Competitive advantages and design features have been discussed and the productive capacity of the research nuclear facility under development has been evaluated [ru

  14. Proceeding of the 7. Seminar on Technology and Safety of Nuclear Power Plants and Nuclear Facilities

    Hastowo, Hudi; Antariksawan, Anhar R.; Soetrisnanto, Arnold Y; Jujuratisbela, Uju; Aziz, Ferhat; Su'ud, Zaki; Suprawhardana, M. Salman

    2002-02-01

    The seventh proceedings of seminar safety and technology of nuclear power plant and nuclear facilities, held by National Nuclear Energy Agency. The Aims of seminar is to exchange and disseminate information about safety and nuclear Power Plant Technology and Nuclear Facilities consist of technology; high temperature reactor and application for national development sustain able and high technology. This seminar level all aspects technology, Power Reactor research reactor, high temperature reactor and nuclear facilities. The article is separated by index

  15. Database for environmental monitoring at nuclear facilities

    Raceanu, M.; Varlam, C.; Enache, A.; Faurescu, I.

    2006-01-01

    To ensure that an assessment could be made of the impact of nuclear facilities on the local environment, a program of environmental monitoring must be established well in advance of nuclear facilities operation. Enormous amount of data must be stored and correlated starting with: location, meteorology, type sample characterization from water to different kind of food, radioactivity measurement and isotopic measurement (e.g. for C-14 determination, C-13 isotopic correction it is a must). Data modelling is a well known mechanism describing data structures at a high level of abstraction. Such models are often used to automatically create database structures, and to generate code structures used to access databases. This has the disadvantage of losing data constraints that might be specified in data models for data checking. Embodiment of the system of the present application includes a computer-readable memory for storing a definitional data table for defining variable symbols representing respective measurable physical phenomena. The definitional data table uniquely defines the variable symbols by relating them to respective data domains for the respective phenomena represented by the symbols. Well established rules of how the data should be stored and accessed, are given in the Relational Database Theory. The theory comprise of guidelines such as the avoidance of duplicating data using technique call normalization and how to identify the unique identifier for a database record. (author)

  16. Database for environmental monitoring in nuclear facilities

    Raceanu, Mircea; Varlam, Carmen; Iliescu, Mariana; Enache, Adrian; Faurescu, Ionut

    2006-01-01

    To ensure that an assessment could be made of the impact of nuclear facilities on the local environment, a program of environmental monitoring must be established well before of nuclear facility commissioning. Enormous amount of data must be stored and correlated starting with: location, meteorology, type sample characterization from water to different kind of foods, radioactivity measurement and isotopic measurement (e.g. for C-14 determination, C-13 isotopic correction it is a must). Data modelling is a well known mechanism describing data structures at a high level of abstraction. Such models are often used to automatically create database structures, and to generate the code structures used to access the databases. This has the disadvantage of losing data constraints that might be specified in data models for data checking. Embodiment of the system of the present application includes a computer-readable memory for storing a definitional data table for defining variable symbols representing the corresponding measurable physical quantities. Developing a database system implies setting up well-established rules of how the data should be stored and accessed what is commonly called the Relational Database Theory. This consists of guidelines regarding issues as how to avoid duplicating data using the technique called normalization and how to identify the unique identifier for a database record. (authors)

  17. Nuclear fuel cycle facility accident analysis handbook

    NONE

    1998-03-01

    The purpose of this Handbook is to provide guidance on how to calculate the characteristics of releases of radioactive materials and/or hazardous chemicals from nonreactor nuclear facilities. In addition, the Handbook provides guidance on how to calculate the consequences of those releases. There are four major chapters: Hazard Evaluation and Scenario Development; Source Term Determination; Transport Within Containment/Confinement; and Atmospheric Dispersion and Consequences Modeling. These chapters are supported by Appendices, including: a summary of chemical and nuclear information that contains descriptions of various fuel cycle facilities; details on how to calculate the characteristics of source terms for releases of hazardous chemicals; a comparison of NRC, EPA, and OSHA programs that address chemical safety; a summary of the performance of HEPA and other filters; and a discussion of uncertainties. Several sample problems are presented: a free-fall spill of powder, an explosion with radioactive release; a fire with radioactive release; filter failure; hydrogen fluoride release from a tankcar; a uranium hexafluoride cylinder rupture; a liquid spill in a vitrification plant; and a criticality incident. Finally, this Handbook includes a computer model, LPF No.1B, that is intended for use in calculating Leak Path Factors. A list of contributors to the Handbook is presented in Chapter 6. 39 figs., 35 tabs.

  18. Nuclear fuel cycle facility accident analysis handbook

    1998-03-01

    The purpose of this Handbook is to provide guidance on how to calculate the characteristics of releases of radioactive materials and/or hazardous chemicals from nonreactor nuclear facilities. In addition, the Handbook provides guidance on how to calculate the consequences of those releases. There are four major chapters: Hazard Evaluation and Scenario Development; Source Term Determination; Transport Within Containment/Confinement; and Atmospheric Dispersion and Consequences Modeling. These chapters are supported by Appendices, including: a summary of chemical and nuclear information that contains descriptions of various fuel cycle facilities; details on how to calculate the characteristics of source terms for releases of hazardous chemicals; a comparison of NRC, EPA, and OSHA programs that address chemical safety; a summary of the performance of HEPA and other filters; and a discussion of uncertainties. Several sample problems are presented: a free-fall spill of powder, an explosion with radioactive release; a fire with radioactive release; filter failure; hydrogen fluoride release from a tankcar; a uranium hexafluoride cylinder rupture; a liquid spill in a vitrification plant; and a criticality incident. Finally, this Handbook includes a computer model, LPF No.1B, that is intended for use in calculating Leak Path Factors. A list of contributors to the Handbook is presented in Chapter 6. 39 figs., 35 tabs

  19. Nuclear facility safeguards as specified by the Czechoslovak administrative law

    Elias, J.; Svab, J.

    1978-01-01

    A study is presented of the legal aspects of nuclear safeguards for the operation of nuclear power facilities evaluating the development of the legal arrangement over the past five years, i.e., encoding nuclear safeguards for nuclear facilities in the new building regulations (Act No. 50/1976 Coll. of Laws on Urban Planning and Building Regulations and implementing provisions). It also discusses the juridical position of State surveillance over the nuclear safety of nuclear facilities and its relation to surveillance carried out by specialized bodies of the State work safety inspection and to surveillance carried out by hygiene inspection bodies. (J.S.)

  20. Remote maintenance system for nuclear facilities

    Maeda, Masafumi

    1993-01-01

    In the facilities related to atomic energy, from the viewpoint of the reduction of radiation exposure of workers and the heightening of the rate of operation of the facilities, the development of remote maintenance system is regarded as important. Meidensha Electric Manufacturing Co., Ltd. developed the bilateral control type manipulator, BILARM-83, in 1979, and has developed high performance manipulator systems. As the design of the plant that realizes the remote operation maintenance of process machinery and equipment during plant operation, the remote maintenance system by canyon cell techniques, which was adopted in Savannah River plant, USA, and has been operated for nearly 50 years, has been known. The concept of the full remote maintenance system by large scale cell techniques was shown and has been developed by Power Reactor and Nuclear Fuel Development Corp. In order to realize the remote maintenance of such large scale cells, Meidensha is developing the both arm type bilateral servo manipulator, the single arm type power manipulator, the transport system for moving them, the power and signal system and so on. Those systems were adopted for the glass solidification facilities. (K.I.)

  1. IAEA safeguards in new nuclear facilities

    Catton, A. [International Atomic Energy Agency, Vienna (Austria); Durbin, K. [United States Department of Energy, Washington, D.C. (United States); Hamilton, A. [International Atomic Energy Agency, Vienna (Austria); Martikka, E. [STUK, Helsinki (Finland); Poirier, S.; Sprinkle, J. K.; Stevens, R. [International Atomic Energy Agency, Vienna (Austria); Whitlock, J. [Atomic Energy of Canada Limited, Chalk River, ON (Canada)

    2014-07-01

    The inclusion of international safeguards early in the design of nuclear facilities offers an opportunity to reduce project risk. It also has the potential to minimize the impact of safeguards activities on facility operations. Safeguards by design (SBD) encourages stakeholders to become familiar with the requirements of their safeguards agreements and to decide when and how they will fulfil those requirements. As one example, modular reactors are at a design stage where SBD can have a useful impact. Modular reactors might be turnkey projects where the operator takes ownership after commissioning. This comes with a legal obligation to comply with International Atomic Energy Agency (IAEA) safeguards requirements. Some of the newcomer countries entering the reactor market have little experience with IAEA safeguards and the associated non-proliferation obligations. To reduce delays or cost increments, one can embed safeguards considerations in the bid and design phases of the project, along with the safety and security considerations. SBD does not introduce any new requirements - it is a process whereby facility designers facilitate the implementation of the existing safeguards requirements. In short, safeguards experts share their expertise with the designers and vice versa. Once all parties understand the fundamentals of all of the operational constraints, they are better able to decide how best to address them. This presentation will provide an overview of SBD activities. (author)

  2. The Canadian safeguards program

    Zarecki, C.W.; Smith, R.M.

    1981-12-01

    In support of the Treaty on the Non-Proliferation of Nuclear Weapons Canada provides technical support to the International Atomic Energy Agency for the development of safeguards relevant to Canadian designed and built nuclear facilities. Some details of this program are discussed, including the philosophy and development of CANDU safeguards systems; the unique equipment developed for these systems; the provision of technical experts; training programs; liaison with other technical organizations; research and development; implementation of safeguards systems at various nuclear facilities; and the anticipated future direction of the safeguards program

  3. Regulatory philosophy and requirements for radiation control in Canadian uranium mine-mill facilities

    Dory, A.B.

    1981-10-01

    The approach the Canadian Atomic Energy Control Board takes in licensing uranium mine/mill facilities is based on a minimum of rigidly set regulatory requirements. The regulations state only the basic objectives: the obligation to acquire a licence, some administrative and reporting requirements, and exposure limits. The regulations are supported by a set of regulatory guides. The operator always has the option of following different procedures if he can demonstrate that they will produce the same or better results. Good relationships exist between the AECB and mine management as well as trade unions. Under this approach, however, it is difficult to take action against uncooperative parties. The Board has decided that a somewhat more formalized system is necessary. New regulations are being drafted, giving more detailed licensing and administrative requirements and covering the areas of ventilation and worker and supervisor education more thoroughly

  4. Seismic design standardization of nuclear facilities

    Reddy, G.R.; Vaze, K.K.

    2011-01-01

    Full text: Structures, Systems and Components (SSCs) of Nuclear Facilities have to be designed for normal operating loads such as dead weight, pressure, temperature etc., and accidental loads such as earthquakes, floods, extreme, wind air craft impact, explosions etc. Man made accidents such as aircraft impact, explosions etc., some times may be considered as design basis event and some times taken care by providing administrative controls. This will not be possible in the case of natural events such as earthquakes, flooding, extreme winds etc. Among natural events earthquakes are considered as most devastating and need to be considered as design basis event. It is generally felt design of SSCs for earthquake loads is very time consuming and expensive. Conventional seismic design approaches demands for large number of supports for systems and components. This results in large space occupation and in turn creates difficulties for maintenance and in service inspection of systems and components. In addition, complete exercise of design need to be repeated for plants being located at different sites due to different seismic demands. However, advanced seismic response control methods will help to standardize the seismic design meeting the safety and economy. These methods adopt passive, semi active and active devices, and base isolators to control the seismic response. In nuclear industry, it is advisable to go for passive devices to control the seismic responses. Ideally speaking, these methods will make the designs made for normal loads can also satisfy the seismic demand without calling for change in material, geometry, layout etc. in the SSCs. This paper explain the basic ideas of seismic response control methods, demonstrate the effectiveness of control methods through case studies and eventually give the procedure to be adopted for seismic design standardization of nuclear facilities

  5. The application of nuclear energy to the Canadian chemical process industry

    Robertson, R.F.S.

    1976-03-01

    A study has been made to determine what role nuclear energy, either electrical or thermal, could play in the Canadian chemical process industry. The study was restricted to current-scale CANDU type power reactors. It is concluded that the scale of operation of the chemical industry is rarely large enough to use blocks of electrical power (e) of 500 MW or thermal power (t) of 1500 MW. Thus, with a few predictable exceptions, the role of nuclear energy in the Canadian chemical industry will be as a general thermal/electrical utility supplier, serving a variety of customers in a particular geographic area. This picture would change if nuclear steam generators of 20 to 50 MW(t) become available and are economically competitive. (author)

  6. Second interim assessment of the Canadian concept for nuclear fuel waste disposal. Volume 1

    Wuschke, D.M.; Gillespie, P.A.; Main, D.E.

    1985-07-01

    The nuclear fuel waste disposal concept chosen for development and assessment in Canada involves the isolation of corrosion-resistant containers of waste in a vault located deep in plutonic rock. As the concept and the assessment tools are developed, periodic assessments are performed to permit evaluation of the methodology and provide feedback to those developing the concept. The ultimate goal of these assessments is to predict what impact the disposal system would have on man and the environment if the concept were implemented. The second assessment was performed in 1984 and is documented in the Second Interim assessment of the Canadian Concept for Nuclear Fuel Waste Disposal Volumes 1 to 4. This volume, entitled Summary, is a condensation of Volumes 2, 3 and 4. It briefly describes the Canadian nuclear fuel waste disposal concept, and the methods and results of the second interim pre-closure and post-closure assessments of that concept. 46 refs

  7. Safety improvements at Canadian nuclear power plants in the aftermath of Fukushima accident

    Rzentkowski, G.; Khouaja, H.

    2014-01-01

    This paper describes the safety review of operating nuclear power plants undertaken by the Canadian Nuclear Safety Commission in light of the March 11, 2011 accident at the Fukushima Daiichi Nuclear Power Plants (NPPs). The review confirmed that the Canadian NPPs are robust and have a strong design relying on multiple layers of defence to protect the public from credible external events. Nevertheless, in the spirit of continuous safety improvements, the review identified a number of recommendations to further strengthen reactor defence-in-depth in preventing and mitigating the consequences of beyond design basis accidents, enhance onsite and offsite emergency response, and improve the CNSC regulatory framework. Progress achieved to date, in implementing these measures, is described in this paper along with a summary of safety benefits for each level of the reactor defence-in-depth. (author)

  8. Safety improvements at Canadian nuclear power plants in the aftermath of Fukushima accident

    Rzentkowski, G.; Khouaja, H. [Canadian Nuclear Safety Commission, Ottawa, ON (Canada)

    2014-07-01

    This paper describes the safety review of operating nuclear power plants undertaken by the Canadian Nuclear Safety Commission in light of the March 11, 2011 accident at the Fukushima Daiichi Nuclear Power Plants (NPPs). The review confirmed that the Canadian NPPs are robust and have a strong design relying on multiple layers of defence to protect the public from credible external events. Nevertheless, in the spirit of continuous safety improvements, the review identified a number of recommendations to further strengthen reactor defence-in-depth in preventing and mitigating the consequences of beyond design basis accidents, enhance onsite and offsite emergency response, and improve the CNSC regulatory framework. Progress achieved to date, in implementing these measures, is described in this paper along with a summary of safety benefits for each level of the reactor defence-in-depth. (author)

  9. Considerations about the licensing process of special nuclear industrial facilities

    Talarico, M.A., E-mail: talaricomarco@hotmail.com [Marinha do Brasil, Rio de Janeiro, RJ (Brazil). Coordenacao do Porgrama de Submarino com Propulsao Nuclear; Melo, P.F. Frutuoso e [Coordenacao dos Programas de Pos-Graduacao em Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear

    2015-07-01

    This paper brings a discussion about the challenges involved in the development of a new kind of nuclear facility in Brazil, a naval base for nuclear submarines, with attention to the licensing process and considerations about the risk-informed decision making application to the licensing process. Initially, a model of such a naval base, called in this work, special industrial facility, is proposed, with its systems and respective sets of basic requirements, in order to make it possible the accomplishment of the special industrial facility support function to the nuclear submarine. A discussion about current challenges to overcome in this project is presented: the challenges due to the new characteristics of this type of nuclear facility; existence of several interfaces between the special industrial facilities systems and nuclear submarine systems in design activities; lack of specific regulation in Brazil to allow the licensing process of special industrial facilities by the nuclear safety authority; and comments about the lack of information from reference nuclear facilities, as is the case with nuclear power reactors (for example, the German Grafenrheinfeld nuclear plant is the reference plant for the Brazilian Angra 2 nuclear plant). Finally, in view of these challenges, an analysis method of special industrial facility operational scenarios to assist the licensing process is proposed. Also, considerations about the application of risk-informed decision making to the special industrial facility activity and licensing process in Brazil are presented. (author)

  10. Considerations about the licensing process of special nuclear industrial facilities

    Talarico, M.A.; Melo, P.F. Frutuoso e

    2015-01-01

    This paper brings a discussion about the challenges involved in the development of a new kind of nuclear facility in Brazil, a naval base for nuclear submarines, with attention to the licensing process and considerations about the risk-informed decision making application to the licensing process. Initially, a model of such a naval base, called in this work, special industrial facility, is proposed, with its systems and respective sets of basic requirements, in order to make it possible the accomplishment of the special industrial facility support function to the nuclear submarine. A discussion about current challenges to overcome in this project is presented: the challenges due to the new characteristics of this type of nuclear facility; existence of several interfaces between the special industrial facilities systems and nuclear submarine systems in design activities; lack of specific regulation in Brazil to allow the licensing process of special industrial facilities by the nuclear safety authority; and comments about the lack of information from reference nuclear facilities, as is the case with nuclear power reactors (for example, the German Grafenrheinfeld nuclear plant is the reference plant for the Brazilian Angra 2 nuclear plant). Finally, in view of these challenges, an analysis method of special industrial facility operational scenarios to assist the licensing process is proposed. Also, considerations about the application of risk-informed decision making to the special industrial facility activity and licensing process in Brazil are presented. (author)

  11. Complementary safety assessment assessment of nuclear facilities - Tricastin facility - AREVA

    2011-01-01

    This complementary safety assessment analyses the robustness of the Areva part of the Tricastin nuclear site to extreme situations such as those that led to the Fukushima accident. This study includes the following facilities: Areva NC Pierrelatte, EURODIF production, Comurhex Pierrelatte, Georges Besse II plant and Socatri. Robustness is the ability for the plant to withstand events beyond which the plant was designed. Robustness is linked to safety margins but also to the situations leading to a sudden deterioration of the accidental sequence. Moreover, safety is not only a matter of design or engineered systems but also a matter of organizing: task organization (including subcontracting) as well as the setting of emergency plans or the inventory of nuclear materials are taken into consideration in this assessment. This report is divided into 10 main chapters: 1) the feedback experience of the Fukushima accident; 2) description of the site and its surroundings; 3) featuring of the site's activities and installations; 4) accidental sequences; 5) protection from earthquakes; 6) protection from floods; 7) protection from other extreme natural disasters; 8) the loss of electrical power and of the heat sink; 9) the management of severe accidents; and 10) subcontracting policy. This analysis has identified 5 main measures to be taken to limit the risks linked to natural disasters: -) continuing the program for replacing the current conversion plant and the enrichment plant; -) renewing the storage of hydrofluoric acid at the de-fluorination workshop; -) assessing the seismic behaviour of some parts of the de-fluorination workshop and of the fluorine fabrication workshop; -) improving the availability of warning and information means in case of emergency; and -) improving the means to mitigate accidental gaseous releases. (A.C.)

  12. Research in artificial intelligence for nuclear facilities

    Uhrig, R.E.

    1990-01-01

    The application of artificial intelligence, in the form of expert systems and neural networks, to the control room activities in a nuclear power plant has the potential to reduce operator error and increase plant safety, reliability, and efficiency. Furthermore, artificial intelligence can increase efficiency and effectiveness in a large number of nonoperating activities (testing, routine maintenance, outage planning, equipment diagnostics, and fuel management) and in research facility experiments. Recent work at the University of Tennessee has demonstrated the feasibility of using neural networks to identify six different transients introduced into the simulation of a steam generator of a nuclear power plant. This work is now being extended to utilize data from a nuclear power plant training simulator. In one configuration, the inputs to the neural network are a subset of the quantities that are typical of those available from the safety parameter display system. The outputs of the network represent the various states of the plant (e.g., normal operation, coolant leakage, inadequate core flow, excessive peak fuel temperature, etc.). Training of the neural network is performed by introducing various faults or conditions to be diagnosed into the simulator. The goal of this work is to demonstrate a neural network diagnostic system that could provide advice to the operators in accordance with the emergency operating procedures

  13. Nuclear at Niagara. 32nd Annual Canadian Nuclear Society conference and 35th CNS/CNA student conference

    NONE

    2011-07-01

    The 32nd Annual Canadian Nuclear Society Conference and 35th CNS/CNA Student Conference was held in Niagara Falls, Ontario, Canada on June 5-8, 2011. The theme of the conference, 'Nuclear at Niagara', brought together scientists, engineers, technologists, senior management, government officials, and students interested in all aspects of nuclear science and technology and its applications, including nuclear power generation, fuel production, uranium mining and refining, management of radioactive wastes and used fuel. Other topics include medical and industrial uses of radionuclides, occupational and environmental radiation protection, the science and technology of nuclear fusion, and associated activities in research and development. and applications of energy from the atom. The central objective of this conference was to exchange views on how nuclear science and technology can best serve the needs of humanity, now and in the future. Over 400 delegates from across Canada and other nuclear countries were in attendance.

  14. Nuclear at Niagara. 32nd Annual Canadian Nuclear Society conference and 35th CNS/CNA student conference

    2011-01-01

    The 32nd Annual Canadian Nuclear Society Conference and 35th CNS/CNA Student Conference was held in Niagara Falls, Ontario, Canada on June 5-8, 2011. The theme of the conference, 'Nuclear at Niagara', brought together scientists, engineers, technologists, senior management, government officials, and students interested in all aspects of nuclear science and technology and its applications, including nuclear power generation, fuel production, uranium mining and refining, management of radioactive wastes and used fuel. Other topics include medical and industrial uses of radionuclides, occupational and environmental radiation protection, the science and technology of nuclear fusion, and associated activities in research and development. and applications of energy from the atom. The central objective of this conference was to exchange views on how nuclear science and technology can best serve the needs of humanity, now and in the future. Over 400 delegates from across Canada and other nuclear countries were in attendance.

  15. Interim Storage Facility for LLW of Decommissioning Nuclear Research Facilities

    Amato, S.; Ugolini, D.; Basile, F. [European Commission, Joint Research Centre, Nuclear Decommissioning and Facility Management Unit, TP 800, Via E. Fermi 2749, 21027 Ispra - VA (Italy)

    2009-06-15

    JRC-Ispra has initiated a Decommissioning and Waste Management (D and WM) Programme of all its nuclear facilities. In the frame of this programme, it has been decided to build an interim storage facility to host conditioned low level waste (LLW) that had been produced during the operation of JRC-Ispra nuclear research reactors and laboratories and that will be produced from their decommissioning. This paper presents the main characteristics of the facility. The storage ISFISF has a rectangular shape with uniform height and it is about 128 m long, 41 m wide and 9 m high. The entire surface affected by the facility, including screening area and access roads, is about 27.000 m{sup 2}. It is divided in three sectors, a central one, about 16 m long, for loading/unloading operations and operational services and two lateral sectors, each about 55 m long, for the conditioned LLW storage. Each storage sector is divided by a concrete wall in two transversal compartments. The ISFISF, whose operational lifetime is 50 years, is designed to host the conditioned LLW boxed in UNI CP-5.2 packages, 2,5 m long, 1.65 m wide, and 1,25 m high. The expected nominal inventory of waste is about 2100 packages, while the maximum storage is 2540 packages, thus a considerably large reserve capacity is available. The packages will be piled in stacks of maximum number of five. The LLW is going to be conditioned with a cement matrix. The maximum weight allowed for each package has been fixed at 16.000 kg. The total radioactivity inventory of waste to be hosted in the facility is about 30 TBq (mainly {beta}/{gamma} emitters). In order to satisfy the structural, seismic, and, most of all, radiological requirements, the external walls of the ISFISF are made of pre-fabricated panels, 32 cm thick, consisting of, from inside to outside, 20 cm of reinforced concrete, 7 cm of insulating material, and again 5 cm of reinforced concrete. For the same reason the roof is made with pre-fabricated panels in

  16. Canadian nuclear power principles for beyond design basis events - supporting rationale

    Elliott, M.; Newman, G.; Bhaloo, A.

    2014-01-01

    The development of the following principles and their rationale began during a special Chief Nuclear Engineers forum held on March 25th, 2013 in Toronto. These principles are intended to provide guidance to the Canadian Nuclear Power Industry in developing responses to the lessons learned from the Fukushima event of March 2011. These principles were accepted and signed off by the Chief Nuclear Officers of each of the three utilities in August 2013 and were presented to the CNSC at a public hearing on August 21, 2013. This document provides the underlying rationale for the principles. (author)

  17. Engineers and scientists in the Canadian nuclear industry 1992-2007

    Stoll, P.

    1993-01-01

    The study utilized a survey of large employers to identify the current level of employment of engineers and scientists in applications of nuclear technology. The labour market implications of three possible alternative future evolutionary paths over the 1992-2007 period were assessed to determine the adequacy of the available labour force to maintain a competitive Canadian presence in domestic and international markets. It is shown that under the nuclear phaseout and no-growth scenarios, the requirements for nuclear experts decline; under the growth scenario, requirements increase, although not at a rate which cannot be met from domestic sources. 2 tabs., 7 refs

  18. Canadian nuclear power principles for beyond design basis events - supporting rationale

    Elliott, M. [OPG Nuclear, Ontario (Canada); Newman, G. [Bruce Power, Ontario (Canada); Bhaloo, A. [New Brunswick Power, New Brunswick (Canada)

    2014-09-15

    The development of the following principles and their rationale began during a special Chief Nuclear Engineers forum held on March 25th, 2013 in Toronto. These principles are intended to provide guidance to the Canadian Nuclear Power Industry in developing responses to the lessons learned from the Fukushima event of March 2011. These principles were accepted and signed off by the Chief Nuclear Officers of each of the three utilities in August 2013 and were presented to the CNSC at a public hearing on August 21, 2013. This document provides the underlying rationale for the principles. (author)

  19. Canadian nuclear power principles for beyond design basis events - supporting rationale

    Elliott, M. [Ontario Power Generation Nuclear, Pickering, ON (Canada); Newman, G. [Bruce Power, Tiverton, ON (Canada); Bhaloo, A. [New Brunswick Power, Fredericton, NB (Canada)

    2014-07-01

    The development of the following principles and their rationale began during a special Chief Nuclear Engineers forum held on March 25th, 2013 in Toronto. These principles are intended to provide guidance to the Canadian Nuclear Power Industry in developing responses to the lessons learned from the Fukushima event of March 2011. These principles were accepted and signed off by the Chief Nuclear Officers of each of the three utilities in August 2013 and were presented to the CNSC at a public hearing on August 21, 2013. This document provides the underlying rationale for the principles. (author)

  20. Operational status of nuclear facilities in Japan. 2012 edition

    2012-01-01

    This document is a compilation which provides an outline of the administration of nuclear facility safety regulations as well as various data including operational status, the status of periodical and safety inspections, the status of issues, and radiation management on nuclear power reactor facilities, reactor facilities in the research and development stage, and fabrication, reprocessing, disposal, and storage facilities in fiscal year 2011 (from April 2011 to March 2012). (J.P.N.)

  1. Governments' role in decommissioning nuclear power facilities

    Guindon, S.; Wendling, R.D.; Gordelier, S.; Soederberg, O.; Averous, J.; Orlando, D.

    2005-01-01

    Many nuclear power plants will reach the end of their operating lives over the next 20 years; some may be life-extended, others may not. This development will precipitate enhanced industrial and regulatory activities in the area of decommissioning. We are also witnessing in many countries a significant shift in the role of government itself: new pressures on governments, such as enhanced attention on environmental impact/mitigation and strategies to implement market-oriented approaches in a variety of sectors, including the energy sector are driving the public policy agenda. The paper will examine the range of policy issues, drawing from recent NEA studies on decommissioning policies and the recent NEA study on Government and Nuclear Energy and, strategies and costs, and other current trends and developments in the nuclear industry and in the nuclear policy fields. The paper will reflect on issues to be addressed during the conference and draw conclusions on the appropriate role of government in this area. Decommissioning policy is very specific and focused: it is not a high level policy/political issue in most instances and rarely gets the same attention as the issue surrounding the future of nuclear energy itself and public concerns regarding safety, waste and economics. One reason why decommissioning does not get the same attention as for example disposal of spent nuclear fuel might be the fact that technology is available for decommissioning, while technology for disposal of spent nuclear fuel is under development. High profile or not, it will remain an important issue for governments and industry alike particularly because of the cost and long lead times involved. In some instances, governments are the owners of the facilities to be decommissioned. In addition, decommissioning factors into issues surrounding the economics of nuclear energy and the sustainability of the nuclear option. Based on results of the Tarragona Seminar (Spain, September 2-4, 2003) and

  2. Remote handling technology for nuclear fuel cycle facilities

    Sakai, Akira; Maekawa, Hiromichi; Ohmura, Yutaka

    1997-01-01

    Design and R and D on nuclear fuel cycle facilities has intended development of remote handling and maintenance technology since 1977. IHI has completed the design and construction of several facilities with remote handling systems for Power Reactor and Nuclear Fuel Development Corporation (PNC), Japan Atomic Energy Research Institute (JAERI), and Japan Nuclear Fuel Ltd. (JNFL). Based on the above experiences, IHI is now undertaking integration of specific technology and remote handling technology for application to new fields such as fusion reactor facilities, decommissioning of nuclear reactors, accelerator testing facilities, and robot simulator-aided remote operation systems in the future. (author)

  3. Physical protection nuclear facilities against sabotage

    Hagemann, A.

    2001-01-01

    Full text: INFCIRC 225 Rev. 4 has introduced the Design Basis Threat, DBT, as a key element of the states physical protection system. The DBT is a definition which determines the level of physical protection of nuclear material during use, storage, transport and of nuclear facilities. It the basis for physical protection concepts and for the design of measures the operator or licensee has to provide. By this means it is also a definition of the responsibility for the physical protection which the operator accepts with the license. The new chapter designated to the physical protection against sabotage which has resulted also in the amendment of the title in INFCIRC 225 demonstrates the grown international concern about the potential consequences of sabotage. More than the physical protection against unauthorized removal the physical protection against sabotage has interfaces with the nuclear safety field. The basis of protection against sabotage therefore is much more based on the facility design-the safety design of the facility. Using the DBT the competent authority is in the position to determine the level of protection against sabotage and the remaining risk which has to be accepted. This risk of course depends on the real threat which is not known in advance. The acceptance of the remaining risk depends on both the assessment of the threat, its credibility and the potential consequences. There has been no serious act of sabotage in the past nor an attempt of. Despite of this the Harnun attack of the Japanese underground and some other recent terrorist activities could have given reasons to reconsider what threat might be credible. The German physical protection system has been developed since the increasing terrorist activities in the 1970s. From the beginning the protection against sabotage played an important role in the German system of physical protection. The requirements for the physical protection against unauthorized removal and against sabotage were

  4. Master Training in Radiological Protection Facilities Radioactive and Nuclear

    Verdu, G.; Mayo, P.; Campayo, J. M.

    2011-01-01

    The master includes general aspects of radiation protection in nuclear facilities. also an advanced module to acquire a high level training highlights as nuclear decommissioning, shielding calculation using advanced codes, particle accelerators, international law, etc.

  5. Decommissioning of the LURE Nuclear Facility

    Pauwels, N.; Horodynski, J.M.; Robert, P.; Tadjeddine, A.

    2013-01-01

    With the goal of obtaining the decommissioning of the LURE nuclear facility, three of its accelerators were dismantled and another was modified to be below the thresh- old of 'Installation Nucleaire de Base' status. Operations were carried out with the strategy of mechanical dismantling with no cutting process. As the civil engineering radioactivity level was low, a great majority of it has been left in place with no process- ing, but compensatory measures have been taken for public and environmental protection. The overall result of these operations is a gain in both cost and operating time. They also contribute to a significant decrease in the risks, including radiological ones. The radiological impact after decommissioning remains acceptable. (authors)

  6. Ventilation safety of facilities comprising nuclear reactors

    Guirlet, J.

    1982-01-01

    The reliability of the ventilation is one of the most important aspects in the prevention of the nuisances that a nuclear installation can provide, since the ventilation is located at the last barrier. A certain number of essential points have been recalled here. But it is necessary to bear in mind other requirements such as the limitation in the number of crossovers, the answers to be found should the system fail, the need to show that ventilation systems do not in themselves bring other nuisances such as noise, irradiation or contamination hazards, likelyhood of recycling the contamination, vibrations, fire. Finally, it is absolutely essential, right from the project stage, that the design ensures that very good accessibility, very easy dismantling and handling, as well as all the facilities needed to make sure of the initial and periodic tests, are guaranteed [fr

  7. Radiation safely culture in nuclear facilities

    Coates, R.

    2018-01-01

    The importance of developing a sound radiation safety culture is a relatively new development in the practical application of radiation protection in operational facilities. It is instructive to trace the evolution of the fundamental approaches to controlling operational exposures, staring with the engineering-based 'Distance, Shielding and Time' mantra, through the growing emphasis on ALARA and systematic management-based approaches, towards a recognition of the importance of developing a more 'hearts and minds' approach based within the wider safety culture of the organization. The underlying requirements for developing a strong radiation safety culture are not novel, and are largely identical to those necessary for nuclear safety culture, which is why an integrated approach to culture within the organization is essential

  8. Environmental Radiation Monitoring Around the Nuclear Facilities

    Choi, Geun Sik; Lee, Chang Woo

    2008-05-15

    Environmental Radiation Monitoring was carried out with measurement of environment. radiation and environmental radioactivity analysis on the sites of KAERI nuclear facilities and Seoul Research Reactors and their environments. The average level of environmental radiation dose measured by an ERM and the accumulated radiation dose by a TLD were almost same level compared with the previous years. The activity of gross {alpha} and gross {beta}, Tritium, Uraniu and Strontium in environmental samples showed a environmental level. The radioactivities of most {gamma}-radionuclides in air particulate, surface water and ground water were less than MDA except {sup 40}K or {sup 7}Be which are natural radionuclides. However, not only {sup 40}K or {sup 7}Be but also {sup 137}Cs were detected at the background level in surface soil, discharge sediment and fallout or pine needle.

  9. Automated entry control system for nuclear facilities

    Ream, W.K.; Espinoza, J.

    1985-01-01

    An entry control system to automatically control access to nuclear facilities is described. The design uses a centrally located console, integrated into the regular security system, to monitor the computer-controlled passage into and out of sensitive areas. Four types of entry control points are used: an unmanned enclosed portal with metal and SNM detectors for contraband detection with positive personnel identification, a bypass portal for contraband search after a contraband alarm in a regular portal also with positive personnel identification, a single door entry point with positive personnel identification, and a single door entry point with only a magnetic card-type identification. Security force action is required only as a response to an alarm. The integration of the entry control function into the security system computer is also described. The interface between the entry control system and the monitoring security personnel utilizing a color graphics display with touch screen input is emphasized. 2 refs., 7 figs

  10. Report on operation of nuclear facilities in 1991

    1992-06-01

    The Slovenian Nuclear Safety Administration (SNSA) prepared a report on nuclear safety in the republic of Slovenia in 1991 as part of its regular practice of reporting on its work to the Government and the National Assembly of the Republic of Slovenia. The report is divided into three thematic chapters covering the activities of the SNSA, the operation of nuclear facilities in Slovenia, the activity of international missions in Slovenia and the operation of nuclear facilities around the world.

  11. Seismic evaluation of existing nuclear facilities. Proceedings

    NONE

    1995-07-01

    Programmes for re-evaluation and upgrading of safety of existing nuclear facilities are presently under way in a number of countries around the world. An important component of these programmes is the re-evaluation of the seismic safety through definition of new seismic parameters at the site and evaluation of seismic capacity of structures, equipment and distribution systems following updated information and criteria. The Seminar is intended to provide a forum for the exchange of information and discussion of the state-of-the-art on seismic safety of nuclear facilities in operation or under construction. Both analytical and experimental techniques for the evaluation of seismic capacity of structures, equipment and distribution systems are discussed. Full scale and field tests of structures and components using shaking tables, mechanical exciters, explosive and shock tests, and ambient vibrations are included in the seminar programme with emphasis on recent case histories. Presentations at the Seminar also include analytical techniques for the determination of dynamic properties of soil-structure systems from experiments as well as calibration of numerical models. Methods and criteria for seismic margin assessment based on experience data obtained from the behaviour of structures and components in real earthquakes are discussed. Guidelines for defining technical requirements for capacity re-evaluation (i.e. acceptable behaviour limits and design and implementation of structure and components upgrades are also presented and discussed. The following topics were covered during 7 sessions: earthquake experience and seismic re-evaluation; country experience in seismic re-evaluation programme; generic WWER studies; analytical methods for seismic capacity re-evaluation; experimental methods for seismic capacity re-evaluation; case studies.

  12. Radiochemical analysis of military nuclear facilities

    Bayramov, A.A.; Bayramova, S.M.

    2012-01-01

    Full text : Radiochemical Analysis is a branch of analytical chemistry comprising an aggregate of methods for qualitatively determining the composition and content of radioisotopes in the products of transformations. Safety and minimization of radiation impact on human and environment are important demand of operation of Military Nuclear Facilities (MNF). In accordance of recommendations of International Commission on Radiological Protection there are next objects of radiochemical analysis: 1) potential sources of radiochemical pollution; 2) environment (objects of environment, human environment including buildings, agricultural production, water, air et al.); 3) human himself (determination of dose from external and internal radiation, chemical poisoning). The chemical analysis can be carried out using, for example, the Gas Chromatography instrument whish separates chemical mixtures and identifies the components at a molecular level. It is one of the most accurate tools for analyzing environmental samples. The Gas Chromatography works on the principle that a mixture will separate into individual substances when heated. The heated gases are carried through a column with an inert gas (such as helium). As the separated substances emerge from the column opening, they flow into the Mass Spectrometry. Mass spectrometry identifies compounds by the mass of the analyte molecule. Newly developed portable Gas Chromatography and Mass Spectrometry are techniques that can be used to separate volatile organic compounds and pesticides. Other uses of Gas Chromatography, combined with other separation and analytical techniques, have been developed for radionuclides, explosive compounds such as royal demolition explosive and trinitrotoluene, and metals. So, based on the many years experience of operation of dangerous MNF, in concordance with norms of radiation and chemical safety it was considered that the tasks of the radiochemical analysis of Military Nuclear Facilities include

  13. Seismic evaluation of existing nuclear facilities. Proceedings

    1995-01-01

    Programmes for re-evaluation and upgrading of safety of existing nuclear facilities are presently under way in a number of countries around the world. An important component of these programmes is the re-evaluation of the seismic safety through definition of new seismic parameters at the site and evaluation of seismic capacity of structures, equipment and distribution systems following updated information and criteria. The Seminar is intended to provide a forum for the exchange of information and discussion of the state-of-the-art on seismic safety of nuclear facilities in operation or under construction. Both analytical and experimental techniques for the evaluation of seismic capacity of structures, equipment and distribution systems are discussed. Full scale and field tests of structures and components using shaking tables, mechanical exciters, explosive and shock tests, and ambient vibrations are included in the seminar programme with emphasis on recent case histories. Presentations at the Seminar also include analytical techniques for the determination of dynamic properties of soil-structure systems from experiments as well as calibration of numerical models. Methods and criteria for seismic margin assessment based on experience data obtained from the behaviour of structures and components in real earthquakes are discussed. Guidelines for defining technical requirements for capacity re-evaluation (i.e. acceptable behaviour limits and design and implementation of structure and components upgrades are also presented and discussed. The following topics were covered during 7 sessions: earthquake experience and seismic re-evaluation; country experience in seismic re-evaluation programme; generic WWER studies; analytical methods for seismic capacity re-evaluation; experimental methods for seismic capacity re-evaluation; case studies

  14. Decommissioning of nuclear facilities: a growing activity in the world

    Anasco, Raul

    2001-01-01

    Nuclear power plants and nuclear facilities are no different from normal buildings and factories. Eventually, they become worn-out or old fashioned, too expensive to maintain or remodel. Decommissioning a nuclear facility is different from retiring other types because of the radioactivity involved. The most important consideration in nuclear decommissioning is to protect workers and the public from exposure to harmful levels of radiation. General criteria and strategies for the decommissioning of nuclear facilities are described as well as the present decommissioning activities of the Argentine CNEA (author)

  15. Nuclear chemistry counting facilities: requirements definition

    O'Brien, D.W.; Baker, J.

    1979-01-01

    In an effort to upgrade outdated instrumentation and to take advantage of current and imminent technologies the Nuclear Chemistry Division at Lawrence Livermore Laboratory is about to undertake a major upgrade of their low level radiation counting and analysis facilities. It is expected that such a project will make a more coordinated data acquisition and data processing system, reduce manual data handling operations and speed up data processing throughput. Before taking on a systems design it is appropriate to establish a definition of the requirements of the facilities. This report examines why such a project is necessary in the context of the current and projected operations, needs, problems, risks and costs. The authors also address a functional specification as a prelude to a system design and the design constraints implicit in the systems implementation. Technical, operational and economic assessments establish necessary boundary conditions for this discussion. This report also establishes the environment in which the requirements definition may be considered valid. The validity of these analyses is contingent on known and projected technical, scientific and political conditions

  16. Protection of nuclear facilities and nuclear materials against malevolent actions

    Cornu, P.; Aurelle, J.; Jalouneix, J.

    2001-01-01

    The french approach for considering malevolent actions affecting the design and operation of nuclear facilities is aimed at determining the extent to which the facilities are protected. When carrying out these studies, operating organizations have to demonstrate that their are complying with the objectives set by the Competent Authority for reducing the risk of internal or external malevolent actions. The approach to be followed consist to determine the sensitivity of each zone and to estimate the vulnerability of the most critical zones to each type of aggression. The sensitivity can be defined by the level of the radiological consequences resulting from a malevolent action. The estimation of the vulnerability is made of the extent to which it is difficult to carry out a malevolent action. if need be, counter-measures are taken to protect zones for which the consequences would be unacceptable compared to the force of the aggression. Counter-measures are intended both to minimise sensitivity and make it more difficult to carry out the aggression envisaged. Acceptable consequences are taken as being those leading to levels of radioactive releases less than, or equal to, those taken into account in the facility safety case. This implies that the vulnerability of the most sensitive zones should be reduced to a minimum so that an acceptable level of protection can be provided for these areas. Emphasis will be paid on the defence in depth approach organized around prevention, management and mitigation measures. (authors)

  17. A trend of robotics in nuclear facilities

    Nakayama, Ryoichi

    1993-01-01

    In order to operate stably nuclear power stations, the periodic inspection determined by the law has been carried out once every year in Japan. For reducing the radiation exposure of workers and improving work efficiency and work quality, the automation and the use of robots have been promoted. Also in fuel reprocessing plants and the facilities for storing radioactive wastes, the remotely operated devices for handling uranium and plutonium are indispensable. The course of the development of the robots for nuclear power plants classified by ages is shown. The research and development have been advanced from special automatic machines of first generation since 1965, through versatile robots of second generation since 1980 to intellectual robots of third generation since 1985. Automatic fuel exchanger, control rod moving mechanism and the ultrasonic flaw detector for pipings are those of first generation. As those of second generation, various movable inspection robots and the manipulators for them were developed. The ultimate working robot completed in 1990 is that of third generation. As the trend of the practical use, monorail type inspection robots and underwater inspection robots and various manipulators are reported. (K.I.)

  18. Learning from elsewhere (problems at US and Canadian nuclear power plants)

    Horgan, J.

    1984-01-01

    This article examines a series of technical and managerial problems that have struck US and Canadian nuclear power plants since 1979. Topics considered include the failure of automatic reactor trip components; ruptures, leaks, and corrosion in steam-generator tubes; pipe cracks in boiling-water reactors; leaks in pressure tubes of Canadian heavy-water reactors; the unreliability of emergency power sources for safety systems; mistakes by operators and other plant personnel; the lack of acceptable emergency-preparedness plans; and poor quality control at construction projects. Most of the discussed problems have solutions, either developed explicitly by a utility most affected by the problem or demonstrated implicitly by a utility that has avoided the problem. It is shown how incidents at sites other than Three Mile Island have expanded the nuclear knowledge base and may help contribute to the solutions of new and older problems

  19. Decommissioning of nuclear facilities in Korea

    Hahn, Pil Soo

    2003-01-01

    In 1996, it was concluded that the first Korea research reactor (KRR-1) and the second Korea research reactor (KRR-2) would be shut down and decommissioned. The main reason for the decommissioning was that the facilities became old and has become surrounded by the urbanised community. And many difficulties, including the higher cost, were faced according to the enhanced regulations. Another reason was the introduction of a new research reactor 'HANARO' in 1995. A project to decommission the reactors was launched on January of 1997 with a goal of release of the site and buildings for unrestricted use by 2008. All the radioactive wastes generated are to be transported to the national repository, planned by the Korea Hydro and Nuclear Power Company (KHNP), and the final evaluation of the residual radioactivity will be made before the clearance of the site. As a first step of the project, a decommissioning plan, including the assessment of the environmental impact and the quality assurance program, was prepared and submitted to the government in 1998. It was approved, after its safety evaluation, by the Korea Institute of Nuclear Safety (KINS) in November of 2000. After some preparative works such as documentation of procedures, the decontamination and dismantling works for the laboratories and hot cells of KRR-2 were started in September, 2001 and finished in December, 2002. The spent fuels that had been generated from the reactors were transferred to the United States in 1998 and no spent fuel remained at the site. All the liquid waste, both operational and decommissioning, was very low in its radioactivity and was treated in a natural evaporation facility of 200 m3/year capacity, developed by KAERI. Especially the laundry waste was treated in a membrane filtering unit for the removal of surfactants before being introduced to the natural evaporator. The solid wastes were segregated and packed in the container of 4 m3, designed according to the ISO-1496, and also in

  20. A Swedish nuclear fuel facility and public acceptance

    Andersson, Bengt A [ABB Atom (Sweden)

    1989-07-01

    For more than ten years the ABB Atom Nuclear Fuel Facility has gained a lot of public attention in Sweden. When the nuclear power debate was coming up in the middle of the seventies, the Nuclear Fuel Facility very soon became a spectacular object. It provided a possibility to bring factual information about nuclear power to the public. Today that public interest still exists. For ABB Atom the Facility works as a tool of information activities in several ways, as a solid base for ABB Atom company presentations. but also as a very practical demonstration of the nuclear power technology to the public. This is valid especially to satisfy the local school demand for a real life object complementary to the theoretical nuclear technology education. Beyond the fact that the Nuclear Fuel Facility is a very effective fuel production plant, it is not too wrong to see it as an important resource for education as well as a tool for improved public relations.

  1. A Swedish nuclear fuel facility and public acceptance

    Andersson, Bengt A.

    1989-01-01

    For more than ten years the ABB Atom Nuclear Fuel Facility has gained a lot of public attention in Sweden. When the nuclear power debate was coming up in the middle of the seventies, the Nuclear Fuel Facility very soon became a spectacular object. It provided a possibility to bring factual information about nuclear power to the public. Today that public interest still exists. For ABB Atom the Facility works as a tool of information activities in several ways, as a solid base for ABB Atom company presentations. but also as a very practical demonstration of the nuclear power technology to the public. This is valid especially to satisfy the local school demand for a real life object complementary to the theoretical nuclear technology education. Beyond the fact that the Nuclear Fuel Facility is a very effective fuel production plant, it is not too wrong to see it as an important resource for education as well as a tool for improved public relations

  2. Study on system integration of robots operated in nuclear fusion facility and nuclear power plant facilities

    Oka, Kiyoshi

    2004-07-01

    A present robot is required to apply to many fields such as amusement, welfare and protection against disasters. The are however only limited numbers of the robots, which can work under the actual conditions as a robot system. It is caused by the following reasons: (1) the robot system cannot be realized by the only collection of the elemental technologies, (2) the performance of the robot is determined by that of the integrated system composed of the complicated elements with many functions, and (3) the respective elements have to be optimized in the integrated robot system with a well balance among them, through their examination, adjustment and improvement. Therefore, the system integration of the robot composed of a large number of elements is the most critical issue to realize the robot system for actual use. In the present paper, I describe the necessary approaches and elemental technologies to solve the issues on the system integration of the typical robot systems for maintenance in the nuclear fusion facility and rescue in the accident of the nuclear power plant facilities. These robots work under the intense radiation condition and restricted space in place of human. In particular, I propose a new approach to realize the system integration of the robot for actual use from the viewpoints of not only the environment and working conditions but also the restructure and optimization of the required elemental technologies with a well balance in the robot system. Based on the above approach, I have a contribution to realize the robot systems working under the actual conditions for maintenance in the nuclear fusion facility and rescue in the accident of the nuclear power plant facilities. (author)

  3. 'What's happening at the Canadian Nuclear Association (CNA): current priorities'

    Clarke, W.L.

    2003-01-01

    An overview of current CNA programs, particularly focused on communications and advertising, regulatory affairs, climate change, and government relations. The presentation will address the principal messages that Canada's nuclear technology sector is endeavouring to get across to the public and to government policy makers. (author)

  4. Proceedings of the 19. Canadian Nuclear Society simulation symposium

    Marleau, G.

    1995-01-01

    A majority of the 31 papers in this symposium on nuclear simulation deal with CANDU reactors. The sessions were organized according to the following subjects: reactor physics, hydrogen behaviour, thermalhydraulics, reactor safety and operation. The individual papers have been abstracted separately

  5. Safety study of fire protection for nuclear fuel cycle facility

    2013-01-01

    Insufficiencies in the fire protection system of the nuclear reactor facilities were pointed out when the fire occurred due to the Niigata prefecture-Chuetsu-oki Earthquake in July, 2007. This prompted the revision of the fire protection safety examination guideline for nuclear reactors as well as commercial guidelines. The commercial guidelines have been endorsed by the regulatory body. Now commercial fire protection standards for nuclear facilities such as the design guideline and the management guideline for protecting fire in the Light Water Reactors (LWRs) are available, however, those to apply to the nuclear fuel cycle facilities such as mixed oxide fuel fabrication facility (MFFF) have not been established. For the improvement of fire protection system of the nuclear fuel cycle facilities, the development of a standard for the fire protection, corresponding to the commercial standard for LWRs were required. Thus, Japan Nuclear Energy Safety Organization (JNES) formulated a fire protection guidelines for nuclear fuel cycle facilities as a standard relevant to the fire protection of the nuclear fuel cycle facilities considering functions specific to the nuclear fuel cycle facilities. In formulating the guidelines, investigation has been conduced on the commercial guidelines for nuclear reactors in Japan and the standards relevant to the fire protection of nuclear facilities in USA and other countries as well as non-nuclear industrial fire protection standards. The guideline consists of two parts; Equipments and Management, as the commercial guidances of the nuclear reactor. In addition, the acquisition of fire evaluation data for a components (an electric cabinet, cable, oil etc.) targeted for spread of fire and the evaluation model of fire source were continued for the fire hazard analysis (FHA). (author)

  6. Proceedings of the Canadian Nuclear Association 26. annual conference

    1986-01-01

    The conference is being held near an imposing array of some of the world's finest nuclear reactors but in a climate for nuclear energy that poses considerable challenge for the future. Recent events at Chernobyl have deflected public attention from the reality that nuclear energy from CANDU reactors is the safest, cleanest and most economic energy option available in several parts of our country. One might well ask 'Will the Chernobyl accident result in a serious long term set-back to global recognition of the need for nuclear power?' Technically it shouldn't do so but politically it may unless the industry takes an innovative and aggressive stand towards providing the necessary assurances to the public of the excellence and safety of well designed reactors such as CANDU. The them of this conference is 'Innovation Leads the Way'. During the next two day we will hear about and discuss innovations in our activities ranging all the way from scientific, technological and market development to the concluding session on what we must now do to dissipate the cloud of Chernobyl. 'Innovation Leads the Way' is a provocative title. We all know what innovation means --changing for the better -- finding new and better ways of doing things. But where are we going? Are we innovative enough to find our way? Exploring the answers to these questions is what this conference is all about. We are seeking the way not only to maintain but to improve the world class performance of our many-facetted industry and the contribution which it can make to meeting the world's energy needs. The process should be assisted through the meaningful communication we will all engage in with friends and colleagues during these next few days. If there is one lesson the nuclear industry world-wide has learned from the events of the past few weeks it is the need for international cooperation and exchange of knowledge and information

  7. Some technical aspects of the nuclear material accounting and control at nuclear fuel cycle facilities

    Miller, O.A.; Babaev, N.S.; Gryazev, V.M.; Gadzhiev, G.I.; Gabeskiriya, V.Ya.

    1977-01-01

    The possibilities of nuclear material accounting and control are discussed at nuclear facilities of fuel cycle (WWER-type reactor, fuel fabrication plant, reprocessing plant and uranium enrichment facility) and zero energy fast reactor facility. It is shown that for nuclear material control the main method is the accounting with the application isotopic correlations at the reprocessing plant and enrichment facility. Possibilities and limitations of the application of destructive and non-destructive methods are discussed for nuclear material determinations at fuel facilities and their role in the accounting and safeguards systems as well as possibilities of the application of neutron method at a zero energy fast reactor facility [ru

  8. Proceedings of the Canadian Nuclear Association 28. annual conference held in Winnipeg, Manitoba, June 12-15, 1988

    1988-01-01

    The proceedings of the 28. CNA (Canadian Nuclear Association) conference contain 28 papers under the following headings: power reactors; fuel cycles; nuclear power and public understanding; future trends; and, applications of nuclear technology. CANDU reactors are emphasized. The individual papers have been abstracted separately

  9. Stochastic Optimization for Nuclear Facility Deployment Scenarios

    Hays, Ross Daniel

    Single-use, low-enriched uranium oxide fuel, consumed through several cycles in a light-water reactor (LWR) before being disposed, has become the dominant source of commercial-scale nuclear electric generation in the United States and throughout the world. However, it is not without its drawbacks and is not the only potential nuclear fuel cycle available. Numerous alternative fuel cycles have been proposed at various times which, through the use of different reactor and recycling technologies, offer to counteract many of the perceived shortcomings with regards to waste management, resource utilization, and proliferation resistance. However, due to the varying maturity levels of these technologies, the complicated material flow feedback interactions their use would require, and the large capital investments in the current technology, one should not deploy these advanced designs without first investigating the potential costs and benefits of so doing. As the interactions among these systems can be complicated, and the ways in which they may be deployed are many, the application of automated numerical optimization to the simulation of the fuel cycle could potentially be of great benefit to researchers and interested policy planners. To investigate the potential of these methods, a computational program has been developed that applies a parallel, multi-objective simulated annealing algorithm to a computational optimization problem defined by a library of relevant objective functions applied to the Ver ifiable Fuel Cycle Simulati on Model (VISION, developed at the Idaho National Laboratory). The VISION model, when given a specified fuel cycle deployment scenario, computes the numbers and types of, and construction, operation, and utilization schedules for, the nuclear facilities required to meet a predetermined electric power demand function. Additionally, it calculates the location and composition of the nuclear fuels within the fuel cycle, from initial mining through

  10. Safety of nuclear fuel cycle facilities. Safety requirements

    2008-01-01

    This publication covers the broad scope of requirements for fuel cycle facilities that, in light of the experience and present state of technology, must be satisfied to ensure safety for the lifetime of the facility. Topics of specific reference include aspects of nuclear fuel generation, storage, reprocessing and disposal. Contents: 1. Introduction; 2. The safety objective, concepts and safety principles; 3. Legal framework and regulatory supervision; 4. The management system and verification of safety; 5. Siting of the facility; 6. Design of the facility; 7. Construction of the facility; 8. Commissioning of the facility; 9. Operation of the facility; 10. Decommissioning of the facility; Appendix I: Requirements specific to uranium fuel fabrication facilities; Appendix II: Requirements specific to mixed oxide fuel fabrication facilities; Appendix III: Requirements specific to conversion facilities and enrichment facilities

  11. The State Surveillance over Nuclear Safety of Nuclear Facilities Act No. 28/1984

    1995-01-01

    The Act lays down responsibilities of the Czechoslovak Atomic Energy Commission in the field of state surveillance over nuclear safety of nuclear facilities; determines the responsibilities of nuclear safety inspectors in their inspection activities; specifies duties of bodies and corporations responsible for nuclear safety of nuclear facilities; stipulates the obligation to set up emergency plans; and specifies penalties imposed on corporations and individuals for noncompliance with nuclear safety provisions. The Act entered into force on 4 April 1984. (J.B.)

  12. Second interim assessment of the Canadian concept for nuclear fuel waste disposal. Volume 2

    Gillespie, P.A.; Wuschke, D.M.; Guvanasen, V.M.; Mehta, K.K.; McConnell, D.B.; Tamm, J.A.; Lyon, R.B.

    1985-12-01

    The nuclear fuel waste disposal concept chosen for development and assessment in Canada involves the burial of corrosion-resistant containers of waste in a vault located deep in plutonic rock in the Canadian Shield. As the concept and the assessment tools are developed, periodic assessments are performed to permit evaluatin of the methodology and provide feedback to those developing the concept. The ultimate goal of these assessments is to predict what impact the disposal system would have if the concept were implemented. The second assessment was performed in 1984 and is documented in Second Interim Assessment of the Canadian Concept for Nuclear Fuel Waste Disposal - Volumes 1 to 4. This volume, entitled Background, discusses Canadian nuclear fuel wastes and the desirable features of a waste disposal method. It outlines several disposal options being considered by a number of countries, including the option chosen for development and assessment in Canada. The reference disposal systems assumed for the second assessment are described, and the approach used for concept assessment is discussed briefly. 79 refs

  13. The Independence of the Nuclear Regulator: Notes from the Canadian Experience

    MacKenzie, B.

    2010-01-01

    The firing of Linda Keen as president and chief executive Officer of the Canadian Nuclear Safety Commission provoked considerable debate within Canada and internationally about the independence of the canadian nuclear regulator. ms. Keen was dismissed from her position from her position at the height of the crisis over a world-wide shortage of medical isotopes caused by the shutdown of the research reactor in Chalk river, Ontario. Under the terms of its licence, the reactor was required to have cooling pumps connected to an emergency power supply as a backup in case of a power outage caused by an event such an earthquake. In november 2007, after it was discovered that the pumps were not connected, the reactor was shut down. As panic over the shortage of medical isotopes grew, the government took three extraordinary measures: first, it issued a directive; second, it introduced emergency legislation in Parliament; and finally, it fired Linda Keen as President of the Commission. This paper examines those three measures and whether they constituted an unwarranted interference with the independence of the Canadian nuclear regulator. (N.C.)

  14. Nuclear orientation facility at Charles University in Prague

    Rotter, M.; Trhlik, M.; Hubalovsky, S.; Srnka, A.; Dupak, J.; Ota, J.; Pari, P.

    2000-01-01

    A low temperature nuclear orientation facility was installed at Charles University in the laboratory of the Department of Low Temperature Physics on the Faculty of Mathematics and Physics in Prague. The solid state as well as nuclear physics research is pursued on this facility. (author)

  15. Decommissioning of nuclear fuel cycle facilities. Safety guide

    2001-01-01

    The objective of this Safety Guide is to provide guidance to regulatory bodies and operating organizations on planning and provision for the safe management of the decommissioning of non-reactor nuclear fuel cycle facilities. While the basic safety considerations for the decommissioning of nuclear fuel cycle facilities are similar to those for nuclear power plants, there are important differences, notably in the design and operating parameters for the facilities, the type of radioactive material and the support systems available. It is the objective of this Safety Guide to provide guidance for the shutdown and eventual decommissioning of such facilities, their individual characteristics being taken into account

  16. Decommissioning of nuclear facilities involving operations with uranium and thorium

    Shum, E.Y.; Neuder, S.M.

    1990-01-01

    When a licensed nuclear facility ceases operation, the U.S. Nuclear Regulatory Commission (NRC) ensures that the facility and its site are decontaminated to acceptable levels so they may safely be released for unrestricted public use. Because specific environmental standards or broad federal guidelines governing release of residual radioactive contamination have not been issued, NRC has developed ad hoc cleanup criteria for decommissioning nuclear facilities that involved uranium and thorium. Cleanup criteria include decontamination of buildings, equipment, and land. We will address cleanup criteria and their rationale; procedures for decommissioning uranium/thorium facilities; radiological survey designs and procedures; radiological monitoring and measurement; and cost-effectiveness to demonstrate compliance

  17. An approach for risk informed safety culture assessment for Canadian nuclear power stations

    Nelson, W.R.

    2010-01-01

    One of the most important components of effective safety and risk management for nuclear power stations is a healthy safety culture. DNV has developed an approach for risk informed safety culture assessment that combines two complementary paradigms for safety and risk management: loss prevention - for preventing and intervening in accidents; and critical function management - for achieving safety and performance goals. Combining these two paradigms makes it possible to provide more robust systems for safety management and to support a healthy safety culture. This approach is being applied to safety culture assessment in partnership with a Canadian nuclear utility. (author)

  18. Emission of Tc-99 from nuclear facilities

    Luxenburger, H.J.; Schuettelkopf, H.; Bohn, B.

    1984-11-01

    No noticeable Tc-activities are emitted from nuclear power stations. The emissions with the gaseous effluents exceed but rarely the detection limit of 25 nCi/h. Likewise, the emission with the liquid effluents remains below the detection limit of about 0.5 nCi/m 3 . Neither can a remarkable emission be recorded from the facilities of the Central Decontamination Services Department (HDB) of KfK. The emissions from the evaporation system for low level solutions and from the evaporation system for low level solutions and from the incineration facility for solid wastes do not exceed or rarely exceed to a minor extent the detection limit of 0.3 pCi/m 3 waste air. Also with the liquid effluents only minor Tc-amounts are discharged of 0.3 nCi/m 3 at the maximum. In the distillate of the medium level solutions discharged from the Karlsruhe Reprocessing Plant (WAK) to HDB as so-called tritiated water 2 nCi/m 3 Tc-99 at the maximum are contained. Only in the gaseous effluents from the evaporation system for medium level solutions emissions of up to 14 pCi/m 3 can be detected. The detection limits are almost permanently exceeded by the gaseous effluents from WAK. Small amounts of Tc-99 of 7 pCi/m 3 exhaust air at the maximum are released to the environment. However, the amount of Tc accumulated over the sampling period is insignificant from the radioecological point of view. (orig./HP) [de

  19. Final report on DOE nuclear facilities

    1991-11-01

    Risk analysis policy and guidance should be developed, especially for the non-DOE nuclear facilities. Minimum standards should be set on issues including risk management, the scope and depth of risk analysis (e.g., site-wide analysis, worker risk), and approaches to treatment of external events. Continued vigilance is required in maintaining operation staffing levels at the DOE research and testing reactors. Safety Analysis Reports should be updated to reflect the evolving configurations of the facilities and the current safety analysis requirements. The high-level waste storage programs at Hanford, Savannah River and INEL were evaluated. The Department of Energy has not adopted a cleanup policy with specific, clear objectives. DOE should define the respective roles of Headquarters, the field offices, and the M ampersand O contractors. The proposed budget priority setting system should not be implemented. The plan to develop a nation-wide programmatic environmental impact statement (PEIS) should be rethought. An environmental impact statement on the total cleanup program is inconsistent with the localized nature of cleanup decisionmaking. DOE must provide for significant improvements in its radiation protection and safety programs to meet current, and future, technical, engineering, and scientific procedures and practices for controlling sources and contamination, performing external and internal dosimetry, and implementing incident response plans, including applicable protective action guides. The culture of safety is not yet well established at Rocky Flats. The philosophy of the Department of Energy and the management of Rocky Flats is not understood, accepted and believed by the work force. The Advisory Committee has serious concerns about whether DOE's current program at WIPP will be able to demonstrate, in a timely manner, compliance with EPA's proposed long-term performance and human intrusion requirements for disposal of TRU and high-level radioactive wastes

  20. European Nuclear Decommissioning Training Facility II

    Demeulemeester, Y.

    2005-01-01

    SCK-CEN co-ordinates a project called European Nuclear Decommissioning Training Facility II (EUNDETRAF II) in the Sixth Framework Programme on Community activities in the field of research, technological development and demonstration for the period 2002 to 2006. This was a continuation of the FP5 project EUNDETRAF. EUNDETRAF II is a consortium of main European decommissioners, such as SCK-CEN, EWN (Energie Werke Nord, Greifswald Germany), Belgatom (Belgium), SOGIN Societa Gestione Impiantio Nucleari, Italy), Universitaet Hannover (Germany), RWE NUKEM (United Kingdom), DECOM Slovakia Slovakia), CEA Centre d'Energie Atomique, France), UKAEA (United Kingdom's Atomic Energy Agency, United Kingdom) and NRG (Nuclear Research and consultancy Group, Netherlands). The primary objective of this project is to bring together this vast skill base and experience; to consolidate it for easy assimilation and to transfer to future generations by organising a comprehensive training programme.Each training course has a one-week theoretical and a one-week practical component. The theoretical part is for a broader audience and consists of lectures covering all the main aspects of a decommissioning. The practical part of the course includes site visits and desk top solutions of anticipated decommissioning problems. Due to operational constraints and safety considerations, the number of participants to this part of the course is strictly limited. The partners intend to organise altogether two two-week EUNDETRAF II training courses over a period of three years. Another goal is to disseminate the existing theory as well as the practical know-how to personnel of the third countries. Finally it is important to bring together the principal decommissioning organisations undertaking various decommissioning activities. The project creates a forum for regular contacts to exchange information and experiences for mutual benefit of these organisations as well as to enhance skill base in Europe to

  1. Modern tornado design of nuclear and other potentially hazardous facilities

    Stevenson, J.D.; Zhao, Y.

    1996-01-01

    Tornado wind loads and other tornado phenomena, including tornado missiles and differential pressure effects, have not usually been considered in the design of conventional industrial, commercial, or residential facilities in the United States; however, tornado resistance has often become a design requirement for certain hazardous facilities, such as large nuclear power plants and nuclear materials and waste storage facilities, as well as large liquefied natural gas storage facilities. This article provides a review of current procedures for the design of hazardous industrial facilities to resist tornado effects. 23 refs., 19 figs., 13 tabs

  2. Human factors in the Canadian nuclear industry: future needs

    Harrison, F.

    2008-01-01

    Currently the industry is facing refurbishment and new builds. At present most licensees in Canada do not have sufficient numbers of Human Factors staff. As a result, the activities of the CNSC are too often focused on providing guidance regarding the application of Human Factors, in addition to reviewing work submitted by the licensee. Greater efficiencies for both the licensee and the CNSC could be realized if licensee staff had greater Human Factors expertise. Strategies for developing Human Factors expertise should be explored through cooperative partnerships with universities, which could be encouraged to include Human Factors courses specific to nuclear. (author)

  3. Remote intelligent nuclear facility monitoring in LabVIEW

    Kucewicz, J.C.; Argo, P.E.; Caffrey, M.; Loveland, R.C.; McNeil, P.J.

    1996-01-01

    A prototype system implemented in LabVIEW for the intelligent monitoring of the movement of radioactive' material within a nuclear facility is presented. The system collects and analyzes radiation sensor and video data to identify suspicious movement of material within the facility. The facility system also transmits wavelet- compressed data to a remote system for concurrent monitoring. 2 refs., 2 figs

  4. Regulatory oversight strategy for chemistry program at Canadian nuclear power plants

    Kameswaran; Ram

    2012-09-01

    Chemistry program is one of the essential programs for the safe operation of a nuclear power plant. It helps to ensure the necessary integrity, reliability and availability of plant structures, systems and components important to safety. Additionally, the program plays an important role in asset preservation, limiting radiation exposure and environmental protection. A good chemistry program will minimize corrosion of materials, reduce activation products, minimize of the buildup of radioactive material leading to occupational radiation exposure and it helps limit the release of chemicals and radioactive materials to the environment. The legal basis for the chemistry oversight at Canadian NPPs is established by the Nuclear Safety and Control Act and its associated regulations. It draws on the Canadian Nuclear Safety Commission's regulatory framework and NPP operating license conditions that include applicable standards such as CAN/CSA N286-05 Management System Requirements for Nuclear Power Plants. This paper focuses on the regulatory oversight strategy used in Canada to assess the performance of chemistry program at the nuclear power plants (NPPs) licensed by CNSC. The strategy consists of a combination of inspection and performance monitoring activities. The activities are further supported from information gathered through staff inspections of cross-cutting areas such as maintenance, corrective-action follow-ups, event reviews and safety related performance indicators. (authors)

  5. PRTR/309 building nuclear facility preliminary

    Cornwell, B.C.

    1994-01-01

    The hazard classification of the Plutonium Recycle Test Reactor (PRTR)/309 building as a ''Radiological Facility'' and the office portions as ''Other Industrial Facility'' are documented by this report. This report provides: a synopsis of the history and facility it's uses; describes major area of the facility; and assesses the radiological conditions for the facility segments. The assessment is conducted using the hazard category threshold values, segmentation methodology, and graded approach guidance of DOE-STD-1027-92

  6. Innovative training techniques in the Canadian nuclear regulatory environment

    Martin, D.J.

    1996-01-01

    One of the contributors to the safety of nuclear installations is properly-trained personnel. This applies equally to the staff of a regulatory agency, as they are charged with the task of evaluating the safety of installations and operations involving radioactive materials. In 1990, the nuclear regulatory agency of Canada, the Atomic Energy Control Board, set up a Training Center to train AECB staff and to provide assistance to foreign regulatory agencies who had asked for such assistance. In setting up the Training Centre, the authors considered factors which adversely affect the efficacy of training courses. The technical content must, of course, be of sufficiently high quality, but there are other, significant factors which are independent of the content: consider a presentation in which the lecturer shows a slide which is unreadable from the back of the room. The training value of this slide is zero, even though the content may be sound. Pursuing this thought, they decided to examine the mechanics of presentations and the form of training materials, with a view to optimizing their effectiveness in training. The results of this examination were that they decided to use three technologies as the basis for production of training, support and presentation materials. This paper briefly describes these technologies and their advantages. The technologies are: desktop publishing, video and multimedia

  7. Development situation about the Canadian CANDU Nuclear Power Generating Stations

    Jeon, Yu Mi; Kim, Yong Hee; Park, Joo Hwan

    2009-07-15

    The CANDU reactor is the most versatile commercial power reactor in the world. The acronym 'CANDU', a registered trademark of Atomic Energy of Canada Limited, stands for 'CANada Deuterium Uranium'. CANDU uses heavy water as moderator and uranium (originally, natural uranium) as fuel. All current power reactors in Canada are of the CANDU type. Canada exports CANDU type reactor in abroad. CANDU type is used as the nuclear power plants to produce electrical. Today, there are 41 CANDU reactors in use around the world, and the design has continuously evolved to maintain into unique technology and performance. The CANDU-6 power reactor offers a combination of proven, superior and state-of-the-art technology. CANDU-6 was designed specifically for electricity production, unlike other major reactor types. One of its characteristics is a very high operating and fuel efficiency. Canada Nuclear Power Generating Stations were succeeded in a commercial reactor of which the successful application of heavy water reactor, natural uranium method and that on-power fuelling could be achieved. It was achieved through the joint development of a major project by strong support of the federal government, public utilities and private enterprises. The potential for customization to any country's needs, with competitive development and within any level of domestic industrial infrastructure, gives CANDU technology strategic importance in the 21st century.

  8. Occupational radiation exposures at Canadian CANDU nuclear power stations

    LeSurf, J.E.; Taylor, G.F.

    1982-09-01

    In Canada, methods to reduce the radiation exposure to workers at nuclear power reactors have been studied and implemented since the early days of the CANDU reactor program. Close collaboration between the designers, the operators, and the manufacturers has reduced the total exposure at each station, the dose requirement to operate and maintain each successive station compared with earlier stations, and the average annual exposure per worker. Specific methods developed to achieve dose reduction include water chemistry; corrosion resistant materials; low cobalt materials; decontamination; hot filtration, improved equipment reliability, maintainability, and accessibility; improved shielding design and location; planning of work for low exposure; improved operating and maintenance procedures; removal of tritium from D 2 O systems and work environments; improved protective clothing; on-power refuelling; worker awareness and training; and many other small improvements. The 1981 occupational dose productivity factors for Pickering A and Bruce A nuclear generating stations were respectively 0.43 and 0.2 rem/MW(e).a

  9. Development situation about the Canadian CANDU Nuclear Power Generating Stations

    Jeon, Yu Mi; Kim, Yong Hee; Park, Joo Hwan

    2009-07-01

    The CANDU reactor is the most versatile commercial power reactor in the world. The acronym 'CANDU', a registered trademark of Atomic Energy of Canada Limited, stands for 'CANada Deuterium Uranium'. CANDU uses heavy water as moderator and uranium (originally, natural uranium) as fuel. All current power reactors in Canada are of the CANDU type. Canada exports CANDU type reactor in abroad. CANDU type is used as the nuclear power plants to produce electrical. Today, there are 41 CANDU reactors in use around the world, and the design has continuously evolved to maintain into unique technology and performance. The CANDU-6 power reactor offers a combination of proven, superior and state-of-the-art technology. CANDU-6 was designed specifically for electricity production, unlike other major reactor types. One of its characteristics is a very high operating and fuel efficiency. Canada Nuclear Power Generating Stations were succeeded in a commercial reactor of which the successful application of heavy water reactor, natural uranium method and that on-power fuelling could be achieved. It was achieved through the joint development of a major project by strong support of the federal government, public utilities and private enterprises. The potential for customization to any country's needs, with competitive development and within any level of domestic industrial infrastructure, gives CANDU technology strategic importance in the 21st century

  10. Seismic safety assessment of nuclear facilities other than NPPs

    Coman, O.; Dragomirescu, A.; Kope, F.; Zemtev, N.

    2003-01-01

    Many research nuclear facilities are much simpler as compared with a Nuclear Power Plant (NPP) and the accident scenarios corresponding to an external initiating events and the relevant shutdown paths are much easier to be identified. Therefore, simpler methods than an EE-PSA can be often involved in the evaluation of the overall risk associated to such nuclear facilities in respect to External Event Hazards. (author)

  11. Environmental radiation monitoring around the nuclear facilities

    Lee, H.D.; Lee, Y.B.; Lee, W.Y.; Park, D.W.; Chung, B.G.

    1980-01-01

    For the KAERI site, various environmental samples were collected three times a month, and the natural environmental radiation levels were also measured at each sampling point. Measurements for gross alpha and beta radioactivities of the samples were routinely measured for all samples. Strontium-90 concentrations were also analysed for the fallout and air samples collected daily basis on the roof of the main building. Accumulated exposure including the possibility of determination of low level environmental radiation field by employing thermoluminescent dosimeter, CaSO 4 : Dsub(y)-0.4 teflon disc type, at 6 posts in on-site of the KAERI. As for Kori site, at 19 points of ON, OFF-site, and at the same time the environmental radiation exposure rate at each sampling point were measured. Several environmental samples such as surface soil, pine needles, water samples, milk sample and pasture samples were collected and analysed on a quarterly basis. As a result of the survey it can be said that no significant release of radiation to the environment due to the operations of nuclear facilities including research reactor at the KAERI and power reactor at the Kori has been found during the period of the survey and monitoring. (author)

  12. Water intaking facility of nuclear power plant

    Koyama, Kazuhito; Iwata, Nobukatsu; Ochiai, Kanehiro.

    1994-01-01

    In a water intaking facility of a nuclear power plant, a dam is disposed at a position near a sea shore for preventing sea water introduced in open conduit from flowing to the outer sea upon ebbing of tsunamis. The upper end of the dam is set lower than the lower end of a water-intake pipe of a sea water pump of an ordinary system. A water-intake pipe is disposed to such a length that a sea water pump of an emergency system continues to suck the sea water when the water level of the introduced sea water is lowered than the upper end of the dam during the ebb tide. In addition, a means for stopping the operation of the sea water pump of the ordinary system upon starting of the ebb is disposed. Upon reactor scram for occurrence of earthquakes and the like, either the sea water pump in the ordinary system or the seawater pump in the emergency system operates to ensure required amount of sea water for cooling the reactor. In addition, even if the level of the sea water is lowered than the upper end of the dam, since the sea water pump in the emergency system continues to suck sea water, unnecessary suction for sea water by the ordinary sea water pumps can be eliminated. (N.H.)

  13. Westinghouse Savannah River Company (WSRC) approach to nuclear facility maintenance

    Harrison, D.W.

    1991-01-01

    The Savannah River Site (SRS) in South Carolina is a 300+ square mile facility owned by the US Department of Energy (DOE) and operated by Westinghouse Savannah River Company (WSRC), the prime contractor; Bechtel Savannah River, Incorporated (BSRI) is a major subcontractor. The site has used all of the five nuclear reactors and it has the necessary nuclear materials processing facilities, as well as waste management and research facilities. The site has produced materials for the US nuclear arsenal and various isotopes for use in space research and nuclear medicine for more than 30 years. In 1989, WSRC took over as prime contractor, replacing E.I. du Pont de Nemours and Company. At this time, a concentrated effort began to more closely align the operating standards of this site with those accepted by the commercial nuclear industry of the United States. Generally, this meant acceptance of standards of the Institute of Nuclear Power Operations (INPO) for nuclear-related facilities at the site. The subject of this paper is maintenance of nuclear facilities and, therefore, excludes discussion of the maintenance of non-nuclear facilities and equipment

  14. Regulatory control of nuclear facility valves and their actuators

    1993-01-01

    The methods and procedures by which the Finnish Centre for Radiation and Nuclear Safety (STUK) regulates valves and their actuators in nuclear power plants and in other nuclear facilities are specified in the guide. The scope of regulation depends on the Safety Class of the valve and the actuator in question. The Safety Classification principles for the systems, structures and components of the nuclear power plants are described in the guide YVL 2.1 and the regulatory control of the nuclear facility safety valves is described in the guide YVL 5.4

  15. Commentary on the Canadian nuclear fuel waste management program

    Sheng, G.; Shemilt, L.W.

    1981-01-01

    A summary of the first formal review of the Technical Advisory Committee (TAC) to Atomic Energy of Canada Limited on the Nuclear Fuel Waste Management Program is presented. The Program is described briefly and the composition and role of TAC in relation to the Program is outlined. Salient points and major recommendations are presented from the First Annual Report of TAC in which geoscience aspects of the Program were emphasized. It is the view of the Committee that overall, the whole Waste Management Program is well conceived, that there are many impressive accomplishments of high quality, that detailed research objectives are becoming more clearly delineated, that there is growing clarification as to the most critical areas in which research needs to be accomplished and that the increasing participation by university and industry scientists and engineers is reassuring

  16. Some basic physics aspects of the Canadian nuclear power program

    Millar, C.H.

    1975-07-01

    The public is aware that nuclear reactors can be made to operate, so this paper treats reactor lattice and core physics as briefly as possible before proceeding to the physical principles of reactor control which currently seems of more public concern. First the role of delayed fission neutrons in slowing down the exponential divergence of a super-critical reactor is outlined. Next the physical basis of the various components of the power coefficient of reactivity is explained together with the methods of adjusting this coefficient toward the desired value. Finally, longer-term reactivity effects are discussed with emphasis on the several effects of Xe-135 'poison' on reactor design and operation. (author)

  17. Report on operation of nuclear facilities in Slovenia in 1991

    1992-11-01

    Slovenian Nuclear Safety Administration (SNSA) is responsible for: nuclear safety, transport of nuclear and radioactive materials, safeguarding nuclear materials, and conducting regulatory process related to liability for nuclear damage, qualification and training of operators at nuclear facilities, quality assurance and inspection of nuclear facilities. The major nuclear facility supervised by SNSA is the Nuclear Power Plant in Krsko with a pressurized water reactor of 632 MW electric power. Beside the nuclear power plant, TRIGA Mark 11 Research Reactor of 250 kW thermal power operates within the Reactor Center of Jozef Stefan Institute. There is an interim storage of low and medium radioactive waste at the Reactor Center. Also the Uranium mine Zirovski Vrh was supervised by SNSA. All the nuclear power facilities in Republic of Slovenia were operating safely in 1991. There were no significant events that could be evaluated as a safety problem or a breach of technical specifications. A great part of activities of SNSA was focused on the next visit of the IAEA OSART team (Operational Safety Assessment Review Team) in Krsko Nuclear Power Plant and on the visit of the INSARR mission (Integrated Safety Assessment of Research Reactors) for the TRIGA Mark 11 Research Reactor. (author)

  18. Data bank for nuclear-physical studies in educational facilities

    Boboshin, I.N.; Varlamov, V.V.; Ishkhanov, B.S.; Kapitonov, I.M.; Lenskaya, N.A.; Surgutanov, V.V.; Khoronenko, A.A.; Chernyaev, A.P.

    1986-01-01

    Purposes and tasks of nuclear data Centers of the USSR Ministry of Education are discussed in short. Files of both bibliographic and factographic nuclear-physical data widely used with the Centres to provide the state organizations and scientists, first of all educational facilities, with nuclear data to increase effectiveness of fundamental and applied investigations and educational process are described

  19. The disposal of Canada's nuclear fuel waste: engineering for a disposal facility

    Simmons, G.R.; Baumgartner, P.

    1994-01-01

    This report presents some general considerations for engineering a nuclear fuel waste disposal facility, alternative disposal-vault concepts and arrangements, and a conceptual design of a used-fuel disposal centre that was used to assess the technical feasibility, costs and potential effects of disposal. The general considerations and alternative disposal-vault arrangements are presented to show that options are available to allow the design to be adapted to actual site conditions. The conceptual design for a used-fuel disposal centre includes descriptions of the two major components of the disposal facility, the Used-Fuel Packaging Plant and the disposal vault; the ancillary facilities and services needed to carry out the operations are also identified. The development of the disposal facility, its operation, its decommissioning, and the reclamation of the site are discussed. The costs, labour requirements and schedules used to assess socioeconomic effects and that may be used to assess the cost burden of waste disposal to the consumer of nuclear energy are estimated. The Canadian Nuclear Fuel Waste Management Program is funded jointly by AECL and Ontario Hydro under the auspices of the CANDU Owners Group. (author)

  20. An assessment of the feasibility of indefinite containment of Canadian nuclear fuel wastes

    Shoesmith, D.W.; King, F.; Ikeda, B.M.

    1995-05-01

    This report presents an analysis of the expected corrosion behaviour of nuclear fuel waste containers in a conceptual Canadian disposal vault. The container materials considered are dilute Ti alloys (Grades-2, -12 and -16) and oxygen-free copper. The corrosive conditions within the disposal vault change with time as the initially trapped oxygen is consumed and as the heat and γ-radiation produced by the waste decays. This evolution of the vault environment is broadly classified into an early, warm and oxidizing period followed by a period of long-term, stable, cool and non-oxidizing conditions. The corrosion behaviour of both types of material during these two periods is discussed, and various models that have been developed to predict the lifetimes of the containers are presented. The conclusion is that indefinite containment of the waste is feasible with both copper and titanium alloys under Canadian disposal conditions. (author). refs., tabs., figs

  1. Human health considerations in the assessment of Canadian concept for the disposal of nuclear fuel wastes

    Baweja, A.S.; Tracy, B.L.; Ahier, B.; Bartlett, S.

    1996-01-01

    In 1978, AECL was mandated by the government of Ontario and the federal government to find a permanent disposal solution for spent nuclear fuels. Canada opted for disposal in plutonic rocks of the Canadian shield. The Canadian concept calls for disposal in crystalline rocks at a depth of 500 to 1000 m below the surface. The spent fuel would be contained in a canister, the canister would be emplaced in a vault containing clay-based buffer materials, and the cavity would be backfilled and sealed with natural materials. A Federal Environmental Assessment Review Panel was formed in 1992 to assess the concept for disposal of the spent fuel. In this paper a brief discussion of the human health impacts of the proposed concept is presented. Our assessment is based on the information provided by AECL, namely, the main EIS document, a summary and nine other supporting documents

  2. STACY and TRACY: nuclear criticality experimental facilities under construction

    Kobayashi, I.; Takeshita, I.; Yanagisawa, H.; Tsujino, T.

    1992-01-01

    Japan Atomic Energy Research Institute is constructing a Nuclear Fuel Cycle Safety Engineering Research Facility, NUCEF, where the following research themes essential for evaluating safety problems relating to back-end technology in nuclear fuel cycle facilities will be studied: nuclear criticality safety research; research on advanced reprocessing processes and partitioning; and research on transuranic waste treatment and disposal. To perform nuclear criticality safety research related to the reprocessing of light water reactor spent fuels, two criticality experimental facilities, STACY and TRACY, are under construction. STACY (Static Criticality Facility) will be used for the study of criticality conditions of solution fuels, uranium, plutonium and their mixtures. TRACY (Transient Criticality Facility) will be used to investigate criticality accident phenomena with uranium solutions. The construction progress and experimental programmes are described in this Paper. (author)

  3. Research and test facilities required in nuclear science and technology

    2009-01-01

    Experimental facilities are essential research tools both for the development of nuclear science and technology and for testing systems and materials which are currently being used or will be used in the future. As a result of economic pressures and the closure of older facilities, there are concerns that the ability to undertake the research necessary to maintain and to develop nuclear science and technology may be in jeopardy. An NEA expert group with representation from ten member countries, the International Atomic Energy Agency and the European Commission has reviewed the status of those research and test facilities of interest to the NEA Nuclear Science Committee. They include facilities relating to nuclear data measurement, reactor development, neutron scattering, neutron radiography, accelerator-driven systems, transmutation, nuclear fuel, materials, safety, radiochemistry, partitioning and nuclear process heat for hydrogen production. This report contains the expert group's detailed assessment of the current status of these nuclear research facilities and makes recommendations on how future developments in the field can be secured through the provision of high-quality, modern facilities. It also describes the online database which has been established by the expert group which includes more than 700 facilities. (authors)

  4. General problems specific to hot nuclear materials research facilities

    Bart, G.

    1996-01-01

    During the sixties, governments have installed hot nuclear materials research facilities to characterize highly radioactive materials, to describe their in-pile behaviour, to develop and test new reactor core components, and to provide the industry with radioisotopes. Since then, the attitude towards the nuclear option has drastically changed and resources have become very tight. Within the changed political environment, the national research centres have defined new objectives. Given budgetary constraints, nuclear facilities have to co-operate internationally and to look for third party research assignments. The paper discusses the problems and needs within experimental nuclear research facilities as well as industrial requirements. Special emphasis is on cultural topics (definition of the scope of nuclear research facilities, the search for competitive advantages, and operational requirements), social aspects (overageing of personnel, recruitment, and training of new staff), safety related administrative and technical issues, and research needs for expertise and state of the art analytical infrastructure

  5. Space Nuclear Thermal Propulsion (SNTP) Air Force facility

    Beck, David F.

    The Space Nuclear Thermal Propulsion (SNTP) Program is an initiative within the US Air Force to acquire and validate advanced technologies that could be used to sustain superior capabilities in the area or space nuclear propulsion. The SNTP Program has a specific objective of demonstrating the feasibility of the particle bed reactor (PBR) concept. The term PIPET refers to a project within the SNTP Program responsible for the design, development, construction, and operation of a test reactor facility, including all support systems, that is intended to resolve program technology issues and test goals. A nuclear test facility has been designed that meets SNTP Facility requirements. The design approach taken to meet SNTP requirements has resulted in a nuclear test facility that should encompass a wide range of nuclear thermal propulsion (NTP) test requirements that may be generated within other programs. The SNTP PIPET project is actively working with DOE and NASA to assess this possibility.

  6. Environmental assessment as a planning tool for the decommissioning of a nuclear research facility in Canada

    Klukas, M.H.; Grondin, D.J.; Helbrecht, R.A.

    2002-01-01

    Whiteshell Laboratories, a nuclear research facility operated by Atomic Energy of Canada Ltd. (AECL), have provided research facilities for the Canadian Nuclear Industry since the early 1960's. In 1997, AECL made a business decision to discontinue research programs and operations at the laboratories. Shortly thereafter the decision was made in agreement with the Federal Government of Canada to decommission the laboratories. In compliance with its own policy and to meet the requirements of the Canadian Legislation, AECL assessed the potential environmental effects of the project. The Environmental Assessment included studies to evaluate he feasibility of leaving two major project components in place; low-level radioactive waste in trenches located at the Whiteshell Laboratories site and river sediments contaminated from operational effluent releases. For both project components, it was determined that managing the wastes in the existing location was environmentally sound. An extensive follow-up program, comprising of additional monitoring and analysis to verify these findings will be implemented. As a result of these assessments and the assessments for other project components it was concluded that the project was not likely to cause significant adverse effects. The assessment decision was accepted by the Minister of the Environment in 2002 April. (author)

  7. Criteria, standards and policies regarding decommissioning of nuclear facilities

    Detilleux, E.; Lennemann, W.L.

    1977-01-01

    At the end of this century, there will probably be around 2500 operating nuclear power reactors, along with all the other nuclear fuel cycle facilities supporting their operation. Eventually these facilities, one by one, will be shut down and it will be necessary to dispose of them as with any redundant industrial facility or plant. Some parts of a nuclear fuel cycle facility can be dismantled by conventional methods, but those parts which have become contaminated with radioactive nuclear products or induced radioactivity must be subject to rigid controls and restrictions and handled by special dismantling and disposal procedures. In many cases, the resulting quantity of radioactive waste is likely to be relatively large and dismantling quite costly. Decommissioning nuclear facilities is a multifaceted problem involving planners, design engineers, operators, waste managers and regulatory authorities. Preparation for decommissioning should begin as early as site selection and plant design. The corner stone for the preparation of a decommissioning programme is the definition of its extent, meeting the requirements for public and environmental protection during the period that the radioactive material is of concern. The paper discusses the decontamination and decommissioning experience at the Eurochemic fuel reprocessing plant, the implications and the knowledge gained from this experience. It includes the results of technical reviews made by the Nuclear Energy Agency of OECD and the International Atomic Energy Agency regarding decommissioning nuclear facilities. The paper notes the special planning that should be arranged between those responsible for the nuclear facility and competent public authorities who should jointly make a realistic determination of the eventual disposition of the nuclear facility, even before it is built. Recommendations cover the responsibilities of nuclear plant entrepreneurs, designers, operators, and public and regulatory authorities

  8. Ground test facility for nuclear testing of space reactor subsystems

    Quapp, W.J.; Watts, K.D.

    1985-01-01

    Two major reactor facilities at the INEL have been identified as easily adaptable for supporting the nuclear testing of the SP-100 reactor subsystem. They are the Engineering Test Reactor (ETR) and the Loss of Fluid Test Reactor (LOFT). In addition, there are machine shops, analytical laboratories, hot cells, and the supporting services (fire protection, safety, security, medical, waste management, etc.) necessary to conducting a nuclear test program. This paper presents the conceptual approach for modifying these reactor facilities for the ground engineering test facility for the SP-100 nuclear subsystem. 4 figs

  9. Design aspects of radiological safety in nuclear facilities

    Patkulkar, D.S.; Purohit, R.G.; Tripathi, R.M.

    2014-01-01

    In order to keep operational performance of a nuclear facility high and to keep occupational and public exposure ALARA, radiological safety provisions must be reviewed at the time of facility design. Deficiency in design culminates in deteriorated system performance and non adherence to safety standards and could sometimes result in radiological incident. Important radiological aspects relevant to safety were compiled based on operating experiences, design deficiencies brought out from past nuclear incidents, experience gained during maintenance, participation in design review of upcoming nuclear facilities and radiological emergency preparedness

  10. Training of nuclear facility personnel: boon or boondoggle

    Remick, F.J.

    1975-01-01

    The training of nuclear facility personnel has been a requirement of the reactor licensing process for over two decades. However, the training of nuclear facility personnel remains a combination of boon and boondoggle. The opportunity to develop elite, well trained, professionally aggressive reactor operation staffs is not being realized to its full potential. Improvements in the selection of personnel, training programs, operational tools and professional pride can result in improved plant operation and contribute to improved plant capacity factors. Industry, regulatory agencies, professional societies and universities can do much to improve standards and quality of the training of nuclear facility personnel and to improve the professional level of plant operation

  11. History of health studies around nuclear facilities: a methodologival consideration

    Tokuhata, G.K.; Smith, M.W.

    1981-01-01

    A brief historical review was made of low-level radiation studies for general populations living around nuclear facilities. In addition, technical and methodological problems were identified and discussed which often arise in all epidemiological studies designed to determine the possible health effects of low-level radiation released from nuclear facilities. Need for extremely large populations for prospective cancer studies was discussed, but accompanying ascertainment difficulties were also emphasized. More epidemiological studies are needed to provide adequate assessment of the potential health hazards of nuclear facilities

  12. Criteria, standards and policies regarding decommissioning of nuclear facilities

    Detilleux, E.; Lennemann, W.

    1977-01-01

    The paper discusses the decontamination and decommissioning experiences encountered at the Eurochemic fuel reprocessing plant, their implications and the knowledge gained from these experiences. It includes the results of technical reviews made by the Nuclear Energy Agency of OECD and the International Atomic Energy Agency regarding decommissioning nuclear facilities. The conlusions which are presented should weigh heavily in the considerations of the national authorities involved in regulating nuclear power programmes. The paper notes the special planning that should be arranged between those responsible for the nuclear facility and competent public authorities who jointly should make a realistic determination of the eventual disposition of the nuclear facility, even before it is built. Recommendations cover the responsibilities of nuclear plant entrepreneurs, designers, operators, and public and regulatory authorities [fr

  13. Beneficial Re-use of Decommissioned Former Nuclear Facilities

    Boing, L.E.

    1997-01-01

    With the decision to decommission a nuclear facility, it is necessary to evaluate whether to fully demolish a facility or to re-use the facility in some capacity. This evaluation is often primarily driven by both the past mission of the site and the facility and the site's perceived future mission. In the case where the facility to be decommissioned is located within a large research or industrial complex and represents a significant resource to the site's future mission, it may be a perfect candidate to be re-used in some fashion. However, if the site is a rather remote older facility with little chance of being modified to today's standards for its re-use, the chances for its re-use will be substantially reduced. In this presentation, some specific cases of former nuclear facilities being decommissioned and re-used will be reviewed and some factors required to be considered in making this decision will be reviewed

  14. The regulatory evaluation of radiation protection training programmes at Canadian nuclear power plants

    Legare, M.; Tennant, D.

    1996-01-01

    The responsibility for providing the necessary assurance that the use of nuclear energy in Canada does not pose undue risk to health, safety, security and the environment is vested with the Atomic Energy Control Board (AECB). This responsibility has led the Operator Certification Division of the AECB to develop methods to obtain assurance that nuclear power plant operations personnel are well trained and adequately competent to perform their duties. The features of the AECB approach to evaluation of training programmes based on a systematic approach to training is described. An overview of the Canadian nuclear power plants' radiation protection qualification levels is given. The developing evaluation process is contributing to the improvement of licensee radiation protection training programmes. This is making possible the transfer of part of the responsibility for licensed personnel radiation protection qualification assessment to the licensees, thus enabling a reduction in the operator certification division formal qualification activities. (author)

  15. Decommissioning of nuclear facilities: Decontamination, disassembly and waste management

    1983-01-01

    The term 'decommissioning', as used within the nuclear industry, means the actions taken at the end of a facility's useful life to retire the facility from service in a manner that provides adequate protection for the health and safety of the decommissioning workers, the general public, and for the environment. These actions can range from merely closing down the facility and a minimal removal of radioactive material coupled with continuing maintenance and surveillance, to a complete removal of residual radioactivity in excess of levels acceptable for unrestricted use of the facility and its site. This latter condition, unrestricted use, is the ultimate goal of all decommissioning actions at retired nuclear facilities. The purpose of this report is to provide an information base on the considerations important to decommissioning, the methods available for decontamination and disassembly of a nuclear facility, the management of the resulting radioactive wastes, and the areas of decommissioning methodology where improvements might be made. Specific sections are devoted to each of these topics, and conclusions are presented concerning the present status of each topic. A summary of past decommissioning experience in Member States is presented in the Appendix. The report, with its discussions of necessary considerations, available operational methods, and waste management practices, together with supporting references, provides an appreciation of the activities that comprise decommissioning of nuclear facilities. It is anticipated that the information presented in the report should prove useful to persons concerned with the development of plans for the decommissioning of retired nuclear facilities

  16. Supervision of the safety culture in nuclear facilities

    2014-11-01

    This brochure issued by the Swiss Federal Nuclear Safety Inspectorate ENSI reports on safety culture aspects in nuclear facilities and ENSI’s activities as a supervisory instance. ENSI is the independent supervisory authority for the nuclear sector in Switzerland. A definition of safety culture is presented and the development of the concepts used in its monitoring are discussed. The main attributes of a good safety culture are discussed. Further, the conceptual basics and principles of such monitoring are looked at and the methods used for the supervision of safety culture in nuclear facilities are described

  17. Nuclear Science: a survey of funding, facilities, and manpower

    1975-01-01

    In 1973 the Committee on Nuclear Science of the National Research Council initiated a re-examination of aspects (funding, manpower, and facilities) of the organization and operation of nuclear science research in order to evaluate any changes in the preceding four years and implications of such changes. The reports of the three ad hoc panels established for this purpose (funding and level of effort, nuclear facilities, manpower and education) are presented. Although they identify current problems in nuclear science, these reports do not provide simple solutions; rather, they attempt to provide updated information for use as background for continuing decisions

  18. Nuclear the next generation. 34th Annual Canadian Nuclear Society conference and 37th CNS/CNA student conference

    NONE

    2013-07-01

    The 34th Annual Canadian Nuclear Society Conference and 37th CNS/CNA Student Conference was held in Toronto, Ontario, Canada on June 10-13, 2013. With the theme of the conference, 'Nuclear the Next Generation{sup ,} the conference actively engaged 400 participants in the many facets of this well-rum event. The conference combined excellent plenary speakers, a full set of technical papers, challenging student poster competitions, and interesting exhibits. The plenary session focussed on the themes: 'Nuclear Power - a Business Driver for the Next Generation'; and, 'Designing - the Next Generation'. The technical session titles were: Reactor and Radiation Physics; Environment and Spent Fuel Management; Operations and Maintenance; Fusion Science and Technology; Advanced Reactors and Fuels; Plant Life Extension, Refurbishment and Aging; Safety and Licensing; Chemistry and Materials; and, Thermalhydraulics. The student conference session was well attended and completed the 4 day event.

  19. Protest: The Canadian pulse

    Lott, J.E.

    1979-01-01

    This popularly written article compares Canadian attitudes to protests against nuclear power to those in the United States. Canadian protesters are more peaceful, expressing their opinions within the law. The article describes the main anti-nuclear groups in Canada and presents the results of public opinion surveys of Canadians on the use of nuclear power for generating electricity. (TI)

  20. Canadian programs on understanding and managing aging degradation of nuclear power plant components

    Chadha, J.A.; Pachner, J.

    1989-06-01

    Maintaining adequate safety and reliability of nuclear power plants and nuclear power plant life assurance and life extension are growing in importance as nuclear plants get older. Age-related degradation of plant components is complex and not fully understood. This paper provides an overview of the Canadian approach and the main activities and their results towards understanding and managing age-related degradation of nuclear power plant components, structures and systems. A number of pro-active programs have been initiated to anticipate, detect and mitigate potential aging degradation at an early stage before any serious impact on plant safety and reliability. These programs include Operational Safety Management Program, Nuclear Plant Life Assurance Program, systematic plant condition assessment, refurbishment and upgrading, post-service examination and testing, equipment qualification, research and development, and participation in the IAEA programs on safety aspects of nuclear power plant aging and life extension. A regulatory policy on nuclear power plants is under development and will be based on the domestic as well as foreign and international studies and experience

  1. Marginalization and challenge: the production of knowledge and landscape in Canadian nuclear waste management policy making

    Stanley, A.E.

    2006-01-01

    Aboriginal peoples have recently become politically significant in Canadian nuclear fuel waste (NFW) management policy making. Their newfound significance comes on the heels of an important challenge to the knowledge and authority of the nuclear industry with respect to its plans for NFW lead by a number of public groups and Aboriginal peoples from across Canada, including the Serpent River First Nation. This dissertation examines the relationships between the discourses of the Serpent River First Nation (SRFN) about their experiences of the nuclear fuel chain and the discourses of the Nuclear Waste Management Organization (NWMO) about the management of NFW. Two trends are found to characterize these relationships: marginalization and challenge. The discourses of the NWMO marginalize the SRFN, excluding their experiences of the nuclear fuel chain, radioactivity, and the effects of nuclear industries from the policy making process. The discourses of the SRFN challenge the claims of the NWMO about the effects of nuclear wastes and radioactivity, as well as about the safe and beneficial development of the nuclear fuel chain. I identify discourses of 'modern risk' and 'citizenship' found in the work of the NWMO as instrumental for maintaining the nuclear industry's control over the production of knowledge about NFW and its effects and subjugating the knowledge of the SRFN. I also identify discourses of identity, oppression, and 'situated knowledge' as important challenges to the content, method and premises of the claims of the nuclear industry about the management of NFW. While I conclude that the NWMO's discourses of risk and citizenship constitute a colonial politics of exclusion, I note that their discourses are contingent on the exclusion of the experiences of the SRFN with the fuel chain. For their accounts to be coherent, the NWMO need to maintain a strategic silence on the overwhelming implication Aboriginal peoples, as a category, in the nuclear fuel chain

  2. Decontamination and decommissioning of nuclear facilities: a literature search

    Sande, W.E.; Freeman, H.D.; Hanson, M.S.; McKeever, R.

    1975-05-01

    is bibliography includes 429 unclassified references to the decontamination and decommissioning of nuclear facilities. The references are arranged in chronological order and cover the period from 1944 through 1974. Subject and author indexes are e provided. (U.S.)

  3. Ensuring the safety of nuclear facilities located in large cities

    Ryazantsev, E.P.; Kolyadin, V.I.; Bylkin, B.K.; Zverkov, Yu.A.

    2002-01-01

    The problems of ensuring the safety of nuclear facilities and other facilities representing a radiation hazard (hereinafter referred to as 'nuclear facilities') which are located in large cities are considered in the light of the experience with the 'Kurchatov Institute' Russian Research Centre. The accumulation of substantial quantities of spent nuclear fuel and radwaste at the Centre was an inevitable consequence of the military and civilian nuclear research programmes which started there in 1943. A comprehensive programme has been developed for reducing the impact of ionizing radiation on the Centre's personnel, the population living near the Centre and the local environment. The authors describe the basic elements of a programme for decommissioning reactor facilities and eliminating spent fuel and radwaste storage sites and also describe how the programme is progressing. (author)

  4. Trend of development of robots for nuclear facilities

    Maki, Hideo; Sasaki, Masayoshi

    1984-01-01

    Robot technology becomes more and more important in the field of atomic energy industries. Hitachi Ltd. has energetically engaged in the development of the robot technology for nuclear facilities, recognizing these situations. The course of the development of robot technology and the robots for nuclear facilities is described. As the practical examples of the robots for nuclear facilities, there have been automatic fuel exchangers, the remotely operated automatic exchangers for control rod driving mechanism, automatic and semi-automatic ultrasonic flaw detectors and so on. As the robots for nuclear facilities under development, control rod driving mechanism disassembling and cleaning system, the volume reduction device for spent fuel channel boxes and control rods and others are reported. (Kako, I.)

  5. Regulatory system for control of nuclear facilities in Bangladesh

    Mollah, A.S.

    2005-01-01

    All human activities have associated risks. Nuclear programme is no exception. The Bangladesh Atomic Energy Commission (BAEC), constituted in February 1973 through the promulgation of the Presidential order 15 of 1973. Functions of BAEC include research and development in peaceful application of atomic energy, generation of electricity and promotion of international relations congenial to implementation of its programmes and projects. In 1993 the Government of Bangladesh promulgated the law on Nuclear Safety and Radiation Control. Considering the human resources, expertise and facilities needed for implementation of the provisions of the NSRC law, BAEC was entrusted with the responsibility to enforce it. The responsibilities of the BAEC cover nuclear and radiological safety within the installations of BAEC and radiological safety in the manifold applications of radioisotopes and radiation sources within the country. An adequate and competent infrastructure has been built to cater to the diverse nuclear and radiation protection requirements of all nuclear facilities in Bangladesh, arising at different stages from site selection to day-to-day operation. In addition, periodic inspections of the nuclear facilities are carried out. The licensing and regulatory inspection systems for controlling of nuclear installations and radiation sources are established. The paper describes the legal provisions, responsibilities and organization of BAEC with special emphasis on nuclear safety and radiation protection of nuclear facilities in Bangladesh. (author)

  6. INTEGRATION OF FACILITY MODELING CAPABILITIES FOR NUCLEAR NONPROLIFERATION ANALYSIS

    Gorensek, M.; Hamm, L.; Garcia, H.; Burr, T.; Coles, G.; Edmunds, T.; Garrett, A.; Krebs, J.; Kress, R.; Lamberti, V.; Schoenwald, D.; Tzanos, C.; Ward, R.

    2011-07-18

    Developing automated methods for data collection and analysis that can facilitate nuclear nonproliferation assessment is an important research area with significant consequences for the effective global deployment of nuclear energy. Facility modeling that can integrate and interpret observations collected from monitored facilities in order to ascertain their functional details will be a critical element of these methods. Although improvements are continually sought, existing facility modeling tools can characterize all aspects of reactor operations and the majority of nuclear fuel cycle processing steps, and include algorithms for data processing and interpretation. Assessing nonproliferation status is challenging because observations can come from many sources, including local and remote sensors that monitor facility operations, as well as open sources that provide specific business information about the monitored facilities, and can be of many different types. Although many current facility models are capable of analyzing large amounts of information, they have not been integrated in an analyst-friendly manner. This paper addresses some of these facility modeling capabilities and illustrates how they could be integrated and utilized for nonproliferation analysis. The inverse problem of inferring facility conditions based on collected observations is described, along with a proposed architecture and computer framework for utilizing facility modeling tools. After considering a representative sampling of key facility modeling capabilities, the proposed integration framework is illustrated with several examples.

  7. Development of simplified decommissioning cost estimation code for nuclear facilities

    Tachibana, Mitsuo; Shiraishi, Kunio; Ishigami, Tsutomu

    2010-01-01

    The simplified decommissioning cost estimation code for nuclear facilities (DECOST code) was developed in consideration of features and structures of nuclear facilities and similarity of dismantling methods. The DECOST code could calculate 8 evaluation items of decommissioning cost. Actual dismantling in the Japan Atomic Energy Agency (JAEA) was evaluated; unit conversion factors used to calculate the manpower of dismantling activities were evaluated. Consequently, unit conversion factors of general components could be classified into three kinds. Weights of components and structures of the facility were necessary for calculation of manpower. Methods for evaluating weights of components and structures of the facility were studied. Consequently, the weight of components in the facility was proportional to the weight of structures of the facility. The weight of structures of the facility was proportional to the total area of floors in the facility. Decommissioning costs of 7 nuclear facilities in the JAEA were calculated by using the DECOST code. To verify the calculated results, the calculated manpower was compared with the manpower gained from actual dismantling. Consequently, the calculated manpower and actual manpower were almost equal. The outline of the DECOST code, evaluation results of unit conversion factors, the evaluation method of the weights of components and structures of the facility are described in this report. (author)

  8. Integration of facility modeling capabilities for nuclear nonproliferation analysis

    Garcia, Humberto; Burr, Tom; Coles, Garill A.; Edmunds, Thomas A.; Garrett, Alfred; Gorensek, Maximilian; Hamm, Luther; Krebs, John; Kress, Reid L.; Lamberti, Vincent; Schoenwald, David; Tzanos, Constantine P.; Ward, Richard C.

    2012-01-01

    Developing automated methods for data collection and analysis that can facilitate nuclear nonproliferation assessment is an important research area with significant consequences for the effective global deployment of nuclear energy. Facility modeling that can integrate and interpret observations collected from monitored facilities in order to ascertain their functional details will be a critical element of these methods. Although improvements are continually sought, existing facility modeling tools can characterize all aspects of reactor operations and the majority of nuclear fuel cycle processing steps, and include algorithms for data processing and interpretation. Assessing nonproliferation status is challenging because observations can come from many sources, including local and remote sensors that monitor facility operations, as well as open sources that provide specific business information about the monitored facilities, and can be of many different types. Although many current facility models are capable of analyzing large amounts of information, they have not been integrated in an analyst-friendly manner. This paper addresses some of these facility modeling capabilities and illustrates how they could be integrated and utilized for nonproliferation analysis. The inverse problem of inferring facility conditions based on collected observations is described, along with a proposed architecture and computer framework for utilizing facility modeling tools. After considering a representative sampling of key facility modeling capabilities, the proposed integration framework is illustrated with several examples.

  9. Integration Of Facility Modeling Capabilities For Nuclear Nonproliferation Analysis

    Gorensek, M.; Hamm, L.; Garcia, H.; Burr, T.; Coles, G.; Edmunds, T.; Garrett, A.; Krebs, J.; Kress, R.; Lamberti, V.; Schoenwald, D.; Tzanos, C.; Ward, R.

    2011-01-01

    Developing automated methods for data collection and analysis that can facilitate nuclear nonproliferation assessment is an important research area with significant consequences for the effective global deployment of nuclear energy. Facility modeling that can integrate and interpret observations collected from monitored facilities in order to ascertain their functional details will be a critical element of these methods. Although improvements are continually sought, existing facility modeling tools can characterize all aspects of reactor operations and the majority of nuclear fuel cycle processing steps, and include algorithms for data processing and interpretation. Assessing nonproliferation status is challenging because observations can come from many sources, including local and remote sensors that monitor facility operations, as well as open sources that provide specific business information about the monitored facilities, and can be of many different types. Although many current facility models are capable of analyzing large amounts of information, they have not been integrated in an analyst-friendly manner. This paper addresses some of these facility modeling capabilities and illustrates how they could be integrated and utilized for nonproliferation analysis. The inverse problem of inferring facility conditions based on collected observations is described, along with a proposed architecture and computer framework for utilizing facility modeling tools. After considering a representative sampling of key facility modeling capabilities, the proposed integration framework is illustrated with several examples.

  10. Draft CSA standard on environmental risk assessments at class I nuclear facilities and uranium mines and mills

    Hart, D.; Garisto, N.; Parker, R.; Kovacs, R.; Thompson, B.

    2012-01-01

    The Canadian Standards Association (CSA) is preparing a draft Standard on environmental risk assessments (ERAs) at Class I nuclear facilities and uranium mines and mills (CSA N288.6). It is being prepared by a technical subcommittee of the CSA N288 Technical Committee, including experts from across the nuclear industry, government and regulatory authorities, and environmental service providers, among others. It addresses the design, implementation, and management of environmental risk assessment programs, and is intended to standardize practice across the industry. This paper outlines the scope of the draft Standard and highlights key features. It is under development and subject to change. (author)

  11. Validity evaluation of internal exposure in nuclear facility decommission

    Wang Xiaoli; Chen Dahua; You Zeyun

    2012-01-01

    During nuclear facility decommission under construction, it is very important for workers to wear respirator to avoid harm of Am aerosols. So the protection effect of respirator is very important. The protection effect of respirator was calculated and evaluated according to the data achieved from engineering practice. The result shows that the protection effect is better than target management value and the respirator is effective to protect workers from harm of Am aerosols. The respirator is applied to other nuclear facility decommission. (authors)

  12. Safety study of fire protection for nuclear fuel cycle facility

    NONE

    2013-08-15

    Based on the investigation of fire protection standards for domestic and foreign nuclear facilities, the fire protection guideline for nuclear fuel cycle facility has been completed. In 2012, trial operation is started by private company using the guideline. In addition, the acquisition of fire evaluation data for a components (electric cable) targeted for spread of fire and the evaluation model of fire source were continued for the fire hazard analysis (FHA). (author)

  13. Deactivation and Storage Issues Shared by Fossil and Nuclear Facilities

    Thomas S. LaGuardia

    1998-01-01

    The deactivation of a power plant, be it nuclear or fossil fueled, requires that the facility be placed in a safe and stable condition to prevent unacceptable exposure of the public or the environment to hazardous materials until the facility can be decommissioned. The conditions at two Texas plants are examined. These plants are fossil fueled, but their conditions might be duplicated at a nuclear plant

  14. A Regulators Systematic Approach to Physical Protection for Nuclear Facilities

    Bayer, Stephan; Doulgeris, Nicholas; Leask, Andrew

    2004-01-01

    This paper outlines the framework for a physical protection regime which needs to be incorporated into the design and construction phases of nuclear facility. The need for physical protection considerations at the outset of the design of nuclear facilities is explained. It also discusses about the consequences of malicious activity and the management of risk. Various risk and consequences evaluations are undertaken, notably using design basis threat methodology. (author)

  15. Physical protection of facilities and special nuclear materials in france

    Jeanpierre, G.

    1980-01-01

    Physical protection of nuclear facilities and special nuclear materials is subject in France to a national governmental regulation which provides for the basic principles to be taken into account and the minimal level of protection deemed necessary. But the responsibility of implementation is left to the facility management and the resulting decentralization allows for maximum efficiency. All safeguards measures comply with the commitments taken at the international level by the French government

  16. Safety study of fire protection for nuclear fuel cycle facility

    2013-01-01

    Based on the investigation of fire protection standards for domestic and foreign nuclear facilities, the fire protection guideline for nuclear fuel cycle facility has been completed. In 2012, trial operation is started by private company using the guideline. In addition, the acquisition of fire evaluation data for a components (electric cable) targeted for spread of fire and the evaluation model of fire source were continued for the fire hazard analysis (FHA). (author)

  17. Security Culture in Physical Protection of Nuclear Material and Facility

    Susyanta-Widyatmaka; Koraag, Venuesiana-Dewi; Taswanda-Taryo

    2005-01-01

    In nuclear related field, there are three different cultures: safety, safeguards and security culture. Safety culture has established mostly in nuclear industries, meanwhile safeguards and security culture are relatively new and still developing. The latter is intended to improve the physical protection of material and nuclear facility. This paper describes concept, properties and factors affecting security culture and interactions among these cultures. The analysis indicates that anybody involving in nuclear material and facility should have strong commitment and awareness of such culture to establish it. It is concluded that the assessment of security culture outlined in this paper is still preliminary for developing and conduction rigorous security culture implemented in a much more complex facility such as nuclear power plant

  18. Radioactive waste disposal - ethical and environmental considerations - A Canadian perspective

    Roots, F.

    1994-01-01

    This work deals with ethical and environmental considerations of radioactive waste disposal in Canada. It begins with the canadian attitudes toward nature and environment. Then are given the canadian institutions which reflect an environmental ethic, the development of a canadian radioactive waste management policy, the establishment of formal assessment and review process for a nuclear fuel waste disposal facility, some studies of the ethical and risk dimensions of nuclear waste decisions, the canadian societal response to issues of radioactive wastes, the analysis of risks associated with fuel waste disposal, the influence of other energy related environmental assessments and some common ground and possible accommodation between the different views. (O.L.). 50 refs

  19. The cost of decommissioning nuclear facilities

    1993-01-01

    This report sets out the results of a National Audit Office investigation to determine the extent of the potential Government liability for nuclear decommissioning, how this is to be financed and the possible implications for the taxpayer. Further effort are needed to improve the nuclear industry's estimates, improve efficiency and face up to the costs of decommissioning. This should also ensure that the full cost of nuclear energy is identified. (author)

  20. Nuclear Security Recommendations on Physical Protection of Nuclear Material and Nuclear Facilities (INFCIRC/225/Revision 5): Recommendations

    2011-01-01

    This publication, Revision 5 of Physical Protection of Nuclear Material and Nuclear Facilities (INFCIRC/225), is intended to provide guidance to States and their competent authorities on how to develop or enhance, implement and maintain a physical protection regime for nuclear material and nuclear facilities, through the establishment or improvement of their capabilities to implement legislative and regulatory programmes. The recommendations presented in this publication reflect a broad consensus among IAEA Member States on the requirements which should be met for the physical protection of nuclear materials and nuclear facilities.

  1. Analysis of general specifications for nuclear facilities environmental monitoring vehicles

    Xu Xiaowei

    2014-01-01

    At present, with the nuclear energy more increasingly extensive application, the continuous stable radiation monitoring has become the focus of the public attention. The main purpose of the environmental monitoring vehicle for the continuous monitoring of the environmental radiation dose rate and the radionuclides concentration in the medium around nuclear facilities is that the environmental radiation level and the radioactive nuclides activity in the environment medium are measured. The radioactive pollution levels, the scope contaminated and the trends of the pollution accumulation are found out. The change trends for the pollution are observed and the monitoring results are explained. The domestic demand of the environmental monitoring for the nuclear facilities is shown in this report. The changes and demands of the routine environmental monitoring and the nuclear emergency monitoring are researched. The revision opinions for EJ/T 981-1995 General specifications for nuclear facilities environmental monitoring vehicles are put forward. The purpose is to regulate domestic environmental monitoring vehicle technical criterion. The criterion makes it better able to adapt and serve the environmental monitoring for nuclear facilities. The technical guarantee is provided for the environmental monitoring of the nuclear facilities. (authors)

  2. Status of ANSI standards on decommissioning of nuclear reprocessing facilities

    Graham, H.B.

    1975-01-01

    A definition of decommissioning is given, and the preparation of ANSI Standard, ''General Design Criteria for Nuclear Reprocessing Facilities'' (N101.3) is discussed. A Eurochemic report, entitled ''The Shutdown of Reprocessing Facilities--Results of Preliminary Studies on the Installations Belonging to Eurochemic,'' was used in the preparation of this standard. (U.S.)

  3. Safety of Nuclear Fuel Cycle Facilities. Safety Requirements (Arabic Edition)

    2015-01-01

    This publication covers the broad scope of requirements for fuel cycle facilities that, in light of the experience and present state of technology, must be satisfied to ensure safety for the lifetime of the facility. Topics of specific relevance include aspects of nuclear fuel generation, storage, reprocessing and disposal

  4. Decommissioning of nuclear facilities: Feasibility, needs and costs

    DeLaney, E.G.; Mickelson, J.R.

    1985-01-01

    The Nuclear Energy Agency's Working Group on Decommissioning is preparing a study entitled ''Decommissioning of Nuclear Facilities: Feasibility, Needs and Costs.'' The study addresses the economics, technical feasibility and waste management aspects of decommissioning larger commercial reactors and nuclear support facilities. Experience on decommissioning small reactors and fuel cycle facilities shows that current technology is generally adequate. Several major projects that are either underway or planned will demonstrate decommissioning of the larger and more complex facilities. This experience will provide a framework for planning and engineering the decommissioning of the larger commercial reactors and fuel cycle facilities. Several areas of technology development are desired for worker productivity improvement, occupational exposure reduction, and waste volume reduction. In order to assess and plan for the decommissioning of large commercial nuclear facilities, projections have been made of the capacity of these facilities that may be decommissioned in the future and the radioactive waste that would be produced from the decommissioning of these facilities. These projections through the year 2025 are based on current data and the OECD reactor capacity forecast through the year 2000. A 25-year operating lifetime for electrical power generation was assumed. The possibilities of plant lifetime extension and the deferral of plant dismantlement make this projection very conservative

  5. Papers presented by A.E.C.L. to the International Conference of the Canadian Nuclear Association

    1964-06-01

    The International Conference of the Canadian Nuclear Association was held in Toronto, Ontario, Canada on May 25-27, 1964. There were six papers presented by Atomic Energy of Canada Limited. The titles were: I. Canada - A Nuclear Power Plant Supplier, by J.L. Gray; II. Nuclear Power Development in Canada and Other Countries, by W.B. Lewis; III. The Development and Some Applications of Cobalt-60 Irradiators, by R.F. Errington; IV. The Definition and Achievement of Development Targets for the Canadian Power Reactor Program, by A.J. Mooradian; V. Recent Applications of Tracers in the Physical Sciences in Canada, by R.H. Betts and J.A. Davies; and, VI. Economic Comparison of Oyster Creek, Nine Mile Point and CANDU-type Stations under Canadian Conditions, by G.A. Pon and R.L. Beck.

  6. Uranium Mining and Nuclear Facilities (Prohibitions) Act 1986 No. 194

    1986-01-01

    The purpose of this Act is to protect the health and safety of the people of New South Wales and its environment. Accordingly it prohibits prospecting or mining for uranium and the construction and operation of nuclear reactors and other facilities in the nuclear fuel cycle. (NEA) [fr

  7. Safety Analysis of Spent Nuclear Fuel and Radwaste Facilities

    Poskas, P.; Ragaisis, V.

    2001-01-01

    The overview of the activities in the Laboratory of Heat Transfer in Nuclear Reactors related with the assessment of thermal, neutronic and radiation characteristics in spent nuclear fuel and radwaste facilities are performed. Activities related with decommissioning of Ignalina NPP are also reviewed. (author)

  8. The decommissioning concept for nuclear facilities in Ukraine

    Yaroslavtsev, G.F.; Korchagin, P.A.

    2000-01-01

    The basic task of the conception is a formulation of the basic directions and priorities, terms of schedules and plans, calculation of costs of works on endurance, preservations, dismantlement of nuclear facilities and returning of territories in the unlimited usage. Independent of the development rate of nuclear energy in Ukraine, this problem must now be solved. (author)

  9. Emergency preparedness and response plan for nuclear facilities in Indonesia

    Nur Rahmah Hidayati; Pande Made Udiyani

    2009-01-01

    All nuclear facilities in Indonesia are owned and operated by the National Nuclear Energy Agency (BATAN). The programs and activities of emergency planning and preparedness in Indonesia are based on the existing nuclear facilities, i.e. research reactors, research reactor fuel fabrication plant, radioactive waste treatment installation and radioisotopes production installation. The assessment is conducted to learn of status of emergency preparedness and response plan for nuclear facilities in Indonesia and to support the preparation of future Nuclear Power Plant. The assessment is conducted by comparing the emergency preparedness and response system in Indonesia to the system in other countries such as Japan and Republic of Korea, since the countries have many Nuclear Power Plants and other nuclear facilities. As a result, emergency preparedness response plan for existing nuclear facility in Indonesia has been implemented in many activities such as environmental monitoring program, facility monitoring equipment, and the continuous exercise of emergency preparedness and response. However, the implementation need law enforcement for imposing the responsibility of the coordinators in National Emergency Preparedness Plan. It also needs some additional technical support systems which refer to the system in Japan or Republic of Korea. The systems must be completed with some real time monitors which will support the emergency preparedness and response organization. The system should be built in NPP site before the first NPP will be operated. The system should be connected to an Off Site Emergency Center under coordination of BAPETEN as the regulatory body which has responsibility to control of nuclear energy in Indonesia. (Author)

  10. Technical requirement of experiments and facilities for fusion nuclear technology

    Abdou, M.; Tillak, M.; Gierszwski, P.; Grover, J.; Puigh, R.; Sze, D.K.; Berwald, D.

    1986-06-01

    The technical issues and requirements of experiments and facilities for fusion nuclear technology (FNT) have been investigated. The nuclear subsystems addressed are: a) blanket, b) radiation shield, c) tritium processing system, and d) plasma interactive components. Emphasis has been placed on the important and complex development problems of the blanket. A technical planning process for FNT has been developed and applied, including four major elements: 1) characterization of issues, 2) quantification of testing requirements, 3) evaluation of facilities, and 4) development of a test plan to identify the role, timing, characteristics and costs of major experiments and facilities

  11. The nuclear safeguards data flow for the item facilities

    Wang Hongjun; Chen Desheng

    1994-04-01

    The constitution of nuclear safeguards data flow for the item facilities is introduced and the main contents are the data flow of nuclear safeguards. If the data flow moves positively, i.e. from source data →supporting documents→accounting records→accounting reports, the systems of records and reports will be constituted. If the data flow moves negatively, the way to trace inspection of nuclear material accounting quality will be constituted

  12. Instrumentation and control in the Canadian nuclear power program -1989 status

    Lepp, R.M.

    1990-01-01

    Canada currently has 18 CANDU Pressurized Heavy Water Reactors in operation and 4 under construction, for an installed nuclear capacity of 15,500 MWe. Most of the reactors are in the province of Ontario where 50% of the electricity is nuclear generated. Atomic Energy of Canada is developing the CANDU-3, a 450 MWe reactor incorporating the latest available technologies, including distributed control. The three Canadian Utilities with CANDU reactors have made a major commitment to full-scope training simulators. In Canada there is a growing commitment to developing major improvements to the interface between the control systems, the field equipment and the operating staff. The development program underway makes extensive use of information technology, particularly expert systems and interactive media tools. Out of this will come an advanced CANDU control concept that should further improve the reliability and availability of CANDU stations. (author). 3 refs

  13. Second interim assessment of the Canadian concept for nuclear fuel waste disposal. Volume 3

    Johansen, K.; Donnelly, K.J.; Gee, J.H.; Green, B.J.; Nathwani, J.S.; Quinn, A.M.; Rogers, B.G.; Stevenson, M.A.; Dunford, W.E.; Tamm, J.A.

    1985-12-01

    The nuclear fuel waste disposal concept chosen for development and assessment in Canada involves the isolation of corrosion-resistant containers of waste in a vault located deep in plutonic rock. As the concept and the assessment tools are developed, periodic assessments are performed to permit evaluation of the methodology and provide feedback to those developing the concept. The ultimate goal of these assessments is to predict what impact the disposal system would have on man and the environment if the concept were implemented. The second such assessment was completed in 1984 and is documented in the Second Interim Assessment of the Canadian Concept for Nuclear Fuel Waste Disposal - Volumes 1-4. This, the third volume of the report, summarizes the pre-closure environmental and safety assessments completed by Ontario Hydro for Atomic Energy of Canada Limited. The preliminary results and their sigificance are discussed. 85 refs

  14. Second interim assessment of the Canadian concept for nuclear fuel waste disposal. Volume 4

    Wuschke, D.M.; Gillespie, P.A.; Mehta, K.K.; Henrich, W.F.; LeNeveu, D.M.; Guvanasen, V.M.; Sherman, G.R.; Donahue, D.C.; Goodwin, B.W.; Andres, T.H.

    1985-12-01

    The nuclear fuel waste disposal concept chosen for development and assessment in Canada involves the isolation of corrosion-resistant containers of waste in a vault located deep in plutonic rock. As the concept and the assessment tools are developed, periodic assessments are performed to permit evaluation of the methodology and provide feedback to those developing the concept. The ultimate goal of these assessments is to predict what impact the disposal system would have on man and the environment if the concept were implemented. The second such assessment was performed in 1984 and is documented in the Second Interim Assessment of the Canadian Concept for Nuclear Fuel Waste Disposal - Volumes 1-4. This volume, entitled Post-Closure Assessment, describes the methods, models and data used to perform the second post-closure assessment. The results are presented and their significance is discussed. Conclusions and planned improvements are listed. 72 refs

  15. Test facilities for evaluating nuclear thermal propulsion systems

    Beck, D.F.; Allen, G.C.; Shipers, L.R.; Dobranich, D.; Ottinger, C.A.; Harmon, C.D.; Fan, W.C.; Todosow, M.

    1992-01-01

    Interagency panels evaluating nuclear thermal propulsion (NTP) development options have consistently recognized the need for constructing a major new ground test facility to support fuel element and engine testing. This paper summarizes the requirements, configuration, and baseline performance of some of the major subsystems designed to support a proposed ground test complex for evaluating nuclear thermal propulsion fuel elements and engines being developed for the Space Nuclear Thermal Propulsion (SNTP) program. Some preliminary results of evaluating this facility for use in testing other NTP concepts are also summarized

  16. A safety decision analysis for Saudi Arabian nuclear research facility

    Abulfaraj, W.H.; Abdul-Fattah, A.F.

    1985-01-01

    Establishment of a nuclear research facility should be the first step in planning for introducing the nuclear energy to Saudi Arabia. The fuzzy set decision theory is selected among different decision theories to be applied for this analysis. Four research reactors from USA are selected for the present study. The IFDA computer code, based on the fuzzy set theory is applied. Results reveal that the FNR reactor is the best alternative for the case of Saudi Arabian nuclear research facility, and MITR is the second best. 17 refs

  17. Nuclear facilities. Revenue Act for 2000 (no. 99-1172)

    Anon.

    1999-01-01

    The article no. 43 of the Revenue Act for 2000 modifies the existing system of tax for basic nuclear facilities. The articles no. 17 and no. 121 are abrogated. The basic nuclear facilities subjected to an authorization procedure (article no. 8, act no. 61-842 of the 2. of August 1961 concerning the abatement of air pollution and odors) have to pay an annual tax with effect from January 1. 2000. For nuclear reactors, tax has to be paid for each unit of the plant. (O.M.)

  18. Organization of the internal dosimetry in the Spanish nuclear facilities

    Manchena, P.; Soliet, E.

    1998-01-01

    From the beginning of the exploitation of the nuclear energy of Espanna, the nuclear facilities have had Services of Personal Dosimetry with the appropriate means to determine the dose. so much internal as external, of the personnel that mentioned facilities works. All the nuclear power stations use advanced systems of teams with object of detecting the radionuclides incorporation in the organism and calculation programs based on the recent recommendations of the International Commission of Radiological Protection (ICRP) for the determination of the derived doses

  19. Technological Advances, Human Performance, and the Operation of Nuclear Facilities

    Corrado, Jonathan K.

    Many unfortunate and unintended adverse industrial incidents occur across the United States each year, and the nuclear industry is no exception. Depending on their severity, these incidents can be problematic for people, the facilities, and surrounding environments. Human error is a contributing factor in many such incidents. This dissertation first explored the hypothesis that technological changes that affect how operators interact within the systems of the nuclear facilities exacerbate the cost of incidents caused by human error. I conducted a review of nuclear incidents in the United States from 1955 through 2010 that reached Level 3 (serious incident) or higher on the International Nuclear Events Scale (INES). The cost of each incident at facilities that had recently undergone technological changes affecting plant operators' jobs was compared to the cost of events at facilities that had not undergone changes. A t-test determined a statistically significant difference between the two groups, confirming the hypothesis. Next, I conducted a follow-on study to determine the impact of the incorporation of new technologies into nuclear facilities. The data indicated that spending more money on upgrades increased the facility's capacity as well as the number of incidents reported, but the incident severity was minor. Finally, I discuss the impact of human error on plant operations and the impact of evolving technology on the 21st-century operator, proposing a methodology to overcome these challenges by applying the systems engineering process.

  20. Strategy selection for the decommissioning of nuclear facilities

    2004-01-01

    As modern nuclear power programmes mature and large, commercial nuclear power plants and fuel cycle facilities approach the end of their useful life by reason of age, economics or change of policy on the use of nuclear power, new challenges associated with decommissioning and dismantling come to the fore. Politicians and the public may expect there to be a 'right answer' to the choice of strategy for a particular type of facility, or even all facilities. Both this seminar and wider experience show that this is not the case. Local factors and national political positions have a significant input and often result in widely differing strategy approaches to broadly similar decommissioning projects. All facility owners represented at the seminar were able to demonstrate a rational process for strategy selection and compelling arguments for the choices made. In addition to the papers that were presented, these proceedings include a summary of the discussions that took place. (author)

  1. Construction Cost Growth for New Department of Energy Nuclear Facilities

    Kubic, Jr., William L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-05-25

    Cost growth and construction delays are problems that plague many large construction projects including the construction of new Department of Energy (DOE) nuclear facilities. A study was conducted to evaluate cost growth of large DOE construction projects. The purpose of the study was to compile relevant data, consider the possible causes of cost growth, and recommend measures that could be used to avoid extreme cost growth in the future. Both large DOE and non-DOE construction projects were considered in this study. With the exception of Chemical and Metallurgical Research Building Replacement Project (CMRR) and the Mixed Oxide Fuel Fabrication Facility (MFFF), cost growth for DOE Nuclear facilities is comparable to the growth experienced in other mega construction projects. The largest increase in estimated cost was found to occur between early cost estimates and establishing the project baseline during detailed design. Once the project baseline was established, cost growth for DOE nuclear facilities was modest compared to non-DOE mega projects.

  2. Nuclear physics at multi-GeV hadron facilities

    Geesaman, D.F.

    1993-01-01

    The important contributions Multi-GeV hadron beam facilities can make to the field of Nuclear Physics have been recognized by the community for a decade. Such a facility has featured prominently in each NSAC planning exercise in this period. As Nuclear Physicists realize they must become more concerned with the quark structure of nuclei and the applications of Quantum Chromodynamics to many body systems, the need for experiments at such facilities has become more urgent. In this talk, I will present a personal view of some of the significant recent Nuclear Physics results with multi-GeV hadron facilities, the most important opportunities which can open up to us in the future, and demonstrate how our field must take advantage of these opportunities to progress. I will also report on the recent discussions in the community to make this possible

  3. Accidents in nuclear facilities: classification, incidence and impact

    Galicia A, J.; Paredes G, L. C.

    2012-10-01

    A general analysis of the 146 accidents reported officially in nuclear facilities from 1945 to 2012 is presented, among them some took place in: power or research nuclear reactors, critical and subcritical nuclear assemblies, handling of nuclear materials inside laboratories belonging to institutes or universities, in radiochemistry industrial plants and nuclear fuel factories. In form graph the incidence of these accidents is illustrated classified for; category, decades, geographical localization, country classification before the OECD, failure type, and the immediate or later victims. On the other hand, the main learned lessons of the nuclear accidents of Three Mile Island, Chernobyl and Fukushima are stood out, among those that highlight; the human factors, the necessity of designs more innovative and major technology for the operation, control and surveillance of the nuclear facilities, to increase the criterions of nuclear, radiological and physics safety applied to these facilities, the necessity to carry out probabilistic analysis of safety more detailed for cases of not very probable accidents and their impact, to revalue the selection criterions of the sites for nuclear locations, the methodology of post-accident sites recovery and major instrumentation for parameters evaluation and the radiological monitoring among others. (Author)

  4. Enhancement of safety at nuclear facilities in Pakistan

    Ahmad, S.A.; Hayat, T.; Azhar, W.

    2006-01-01

    Pakistan is benefiting from nuclear technology mostly in health and energy sectors as well as agriculture and industry and has an impeccable safety record. At the national level uses of nuclear technology started in 1955 resulting in the operation of Karachi Radioisotope Center, Karachi, in December 1960. Pakistan Nuclear Safety Committee (PNSC) was formulated in 1964 with subsequent promulgation of Pakistan Atomic Energy Commission (PAEC) Ordinance in 1965 to cope with the anticipated introduction of a research reactor, namely PARR-I, and a nuclear power plant, namely KANUPP. Since then Pakistan's nuclear program has expanded to include numerous nuclear facilities of varied nature. This program has definite economic and social impacts by producing electricity, treating and diagnosing cancer patients, and introducing better crop varieties. Appropriate radiation protection includes a number of measures including database of sealed radiation sources at PAEC operated nuclear facilities, see Table l, updated during periodic physical verification of these sources, strict adherence to the BSS-115, IAEA recommended enforcement of zoning at research reactors and NPPs, etc. Pakistan is party to several international conventions and treaties, such as Convention of Nuclear Safety and Early Notification, to improve and enhance safety at its nuclear facilities. In addition Pakistan generally and PAEC particularly believes in a blend of prudent regulations and good/best practices. This is described in this paper. (Author)

  5. Environmental licensing of nuclear facilities: compatibility of technical competencies

    Shu, J.; Paiva, R.L.C. de; Mezrahi, A.; Cardoso, E.M.; Aquino, W.P.; Deppe, A.L.; Menezes, R.M.; Prado, V.; Franco, N.M.F.L.; Nouailhetas, Y.; Xavier, A.M.

    1996-01-01

    The Brazilian Nuclear Energy Commission (CNEN) has the technical competency for diagnosing environmental radiological impacts, as well as evaluating the safety and requiring adequate control of the facilities which, due to their activities, represent a potential risk of radiological contamination for the environment. The institution is responsible for emission of radioprotection guidelines, controls and surveys in nuclear safety according to the country's regulations and international recommendations. The methodology to assure the limitation of radiation exposure is consequence from shared control over the nuclear activities, in special the nuclear facilities. According to the Federal Constitution of 1988, the nuclear activities must be under exclusive control of the Union in special related to the nuclear policies, economical, laboral and nuclear safety aspects, while the health and environmental controls of these activities are shared by the Federation, Union, States, Federal District and Counties. The controls related to specific aspects have to be harmonized in such a way to be optimized and effective. In this paper the results of compatibilization of nuclear legislation and environmental legislation are presented aiming to optimize the licensing of nuclear facilities. (author)

  6. Upgrade and Development of Nuclear Data Production Test Facility

    NONE

    2007-04-15

    It is necessary to improve the Pohang Neutron Facility (PNF) in order to be used as a nuclear data production facility for users in both domestic and abroad. We improved following items: (1) upgrade the electron linac, (2) collimators inside the TOF beam pipe, (3) the development and installation of an automatic sample changer, (4) the extension of the TOF beam line, and (5) the data acquisition system. We would like to establish a utilization system for users to measure the nuclear data at the PNF. To do this, we made manuals for the accelerator operation and the data acquisition system. We also made an application form to apply for users to measure the nuclear data in both domestic and abroad. The main object of the Pohang Neutron Facility is to measure the nuclear data in the neutron energy region from thermal neutron to few hundreds of eV. In addition to neutron beams produced at the PNF, photon and electron beams are produced in this facility. We thus utilize this facility for other fields, such as test facility for detectors, activation experiments, polarized neutron beam source, and so on. In addition to these, we could use this facility for training students

  7. Upgrade and development of nuclear data production test facility

    Namkung, Won; Ko, I. S.; Cho, M. H.; Lee, Y. S.; Kang, H. S. [Pohang Univ. of Science and Technology, Pohang (Korea, Republic of); Kim, G. N. [Kyungpook National Univ., Daegu (Korea, Republic of); Koh, S. K. [Univ. of Ulsan, Ulsan (Korea, Republic of); Ro, T. I. [Donga Univ., Busan (Korea, Republic of); Choi, G. U. [Korea Research Institute of Standards and Science, Daejeon (Korea, Republic of)

    2005-04-15

    It is necessary to improve the Pohang Neutron Facility (PNF) in order to be used as a nuclear data production facility for users in both domestic and abroad. We improved following items: upgrade the electron linac, collimators inside the TOF beam pipe, the development and installation of an automatic sample changer, the extension of the TOF beam line, and the data acquisition system. We would like to establish a utilization system for users to measure the nuclear data at the PNF. To do this, we made manuals for the accelerator operation and the data acquisition system. We also made an application form to apply for users to measure the nuclear data in both domestic and abroad. The main object of the Pohang Neutron Facility is to measure the nuclear data in the neutron energy region from thermal neutron to few hundreds of eV. In addition to neutron beams produced at the PNF, photon and electron beams are produced in this facility. We thus utilize this facility for other fields, such as test facility for detectors, activation experiments, polarized neutron beam source, and so on. In addition to these, we could use this facility for training students.

  8. Study on archive management for nuclear facility decommissioning projects

    Huang Ling; Gong Jing; Luo Ning; Liao Bing; Zhou Hao

    2011-01-01

    This paper introduces the main features and status of the archive management for nuclear facility decommissioning projects, and explores and discusses the countermeasures in its archive management. Taking the practice of the archive management system of a reactor decommissioning project as an example, the paper illustrates the establishment of archive management system for the nuclear facility decommissioning projects. The results show that the development of a systematic archive management principle and system for nuclear decommissioning projects and the construction of project archives for the whole process from the design to the decommissioning by digitalized archive management system are one effective route to improve the complete, accurate and systematic archiving of project documents, to promote the standardization and effectiveness of the archive management and to ensure the traceability of the nuclear facility decommissioning projects. (authors)

  9. Nuclear facility safeguards systems modeling using discrete event simulation

    Engi, D.

    1977-01-01

    The threat of theft or dispersal of special nuclear material at a nuclear facility is treated by studying the temporal relationships between adversaries having authorized access to the facility (insiders) and safeguards system events by using a GASP IV discrete event simulation. The safeguards system events--detection, assessment, delay, communications, and neutralization--are modeled for the general insider adversary strategy which includes degradation of the safeguards system elements followed by an attempt to steal or disperse special nuclear material. The performance measure used in the analysis is the estimated probability of safeguards system success in countering the adversary based upon a predetermined set of adversary actions. An exemplary problem which includes generated results is presented for a hypothetical nuclear facility. The results illustrate representative information that could be utilized by safeguards decision-makers

  10. Feedback experience from the decommissioning of Spanish nuclear facilities

    Santiago, J.L.

    2008-01-01

    The Spain has accumulated significant experience in the field of decommissioning of nuclear and radioactive facilities. Relevant projects include the remediation of uranium mills and mines, the decommissioning of research reactors and nuclear research facilities and the decommissioning of gas-graphite nuclear power plants. The decommissioning of nuclear facilities in Spain is undertaken by ENRESA, who is also responsible for the management of radioactive wastes. The two most notable projects are the decommissioning of the Vandellos I nuclear power plant and the decommissioning of the CIEMAT nuclear research centre. The Vandellos I power plant was decommissioned in about five years to what is known as level 2. During this period, the reactor vessel was confined, most plant systems and components were dismantled, the facility was prepared for a period of latency and a large part of the site was restored for subsequent release. In 2005 the facility entered into the phase of dormancy, with minimum operating requirements. Only surveillance and maintenance activities are performed, among which special mention should be made to the five-year check of the leak tightness of the reactor vessel. After the dormancy period (25 - 30 years), level 3 of decommissioning will be initiated including the total dismantling of the remaining parts of the plant and the release of the whole site for subsequent uses. The decommissioning of the CIEMAT Research Centre includes the dismantling of obsolete facilities such as the research reactor JEN-1, a pilot reprocessing plant, a fuel fabrication facility, a conditioning plant for liquid and a liquid waste storage facility which were shutdown in the early eighties. Dismantling works have started in 2006 and will be completed by 2009. On the basis of the experience gained in the above mentioned sites, this paper describes the approaches adopted by ENRESA for large decommissioning projects. (author)

  11. Seismic reevaluation of nuclear facilities worldwide: Overview and status

    Campbell, R.D.; Hardy, G.S.; Ravindra, M.K.; Johnson, J.J.; Hoy, A.J.

    1995-01-01

    Existing nuclear facilities throughout the world are being subjected to severe scrutiny of their safety in tile event of an earthquake. In the United States, there have been several licensing and safety review issues for which industry and regulatory agencies have cooperated to develop rational and economically feasible criteria for resolving the issues. Currently, all operating nuclear power plants in the United States are conducting an Individual Plant Examination of External Events, including earthquakes beyond tile design basis. About two-thirds of tile operating plants are conducting parallel programs for verifying, tile seismic adequacy of equipment for the design basis earthquake. The U.S. Department of Energy is also beginning to perform detailed evaluations of their facilities, many of which had little or no seismic design. Western European countries also have been reevaluating their older nuclear power plants for seismic events often adapting the criteria developed in the United States. With the change in tile political systems in Eastern Europe, there is a strong emphasis from their Western European neighbors to evaluate and Upgrade tile safely of their operating nuclear power plants. Finally, nuclear facilities in Asia are, also, being evaluated for seismic vulnerabilities. This paper focuses oil tile methodologies that have been developed for reevaluation of existing nuclear power plants and presents examples of the application of these methodologies to nuclear facilities worldwide. (author)

  12. Seismic reevaluation of nuclear facilities worldwide: Overview and status

    Campbell, R D; Hardy, G S; Ravindra, M K [EQE International, Irvine, CA (United States); Johnson, J J [EQE International, San Francisco, CA (United States); Hoy, A J [EQE International Ltd., Birchwood, Warrington (United Kingdom)

    1995-07-01

    Existing nuclear facilities throughout the world are being subjected to severe scrutiny of their safety in tile event of an earthquake. In the United States, there have been several licensing and safety review issues for which industry and regulatory agencies have cooperated to develop rational and economically feasible criteria for resolving the issues. Currently, all operating nuclear power plants in the United States are conducting an Individual Plant Examination of External Events, including earthquakes beyond tile design basis. About two-thirds of tile operating plants are conducting parallel programs for verifying, tile seismic adequacy of equipment for the design basis earthquake. The U.S. Department of Energy is also beginning to perform detailed evaluations of their facilities, many of which had little or no seismic design. Western European countries also have been reevaluating their older nuclear power plants for seismic events often adapting the criteria developed in the United States. With the change in tile political systems in Eastern Europe, there is a strong emphasis from their Western European neighbors to evaluate and Upgrade tile safely of their operating nuclear power plants. Finally, nuclear facilities in Asia are, also, being evaluated for seismic vulnerabilities. This paper focuses oil tile methodologies that have been developed for reevaluation of existing nuclear power plants and presents examples of the application of these methodologies to nuclear facilities worldwide. (author)

  13. Automated approach to nuclear facility safeguards effectiveness evaluation

    1977-01-01

    Concern over the security of nuclear facilities has generated a need for a reliable, time efficient, and easily applied method of evaluating the effectiveness of safeguards systems. Such an evaluation technique could be used (1) by the Nuclear Regulatory Commission to evaluate a licensee's proposal, (2) to assess the security status of a system, or (3) to design and/or upgrade nuclear facilities. The technique should be capable of starting with basic information, such as the facility layout and performance parameters for physical protection components, and analyzing that information so that a reliable overall facility evaluation is obtained. Responding to this expressed need, an automated approach to facility safeguards effectiveness evaluation has been developed. This procedure consists of a collection of functional modules for facility characterization, critical path generation, and path evaluation combined into a continuous stream of operations. The technique has been implemented on an interactive computer-timesharing system and makes use of computer graphics for the handling and presentation of information. Using this technique a thorough facility evaluation can be made by systematically varying parameters that characterize the physical protection components of a facility according to changes in perceived adversary attributes and strategy, environmental conditions, and site status

  14. Standard Guide for Preparing Characterization Plans for Decommissioning Nuclear Facilities

    American Society for Testing and Materials. Philadelphia

    2009-01-01

    1.1 This standard guide applies to developing nuclear facility characterization plans to define the type, magnitude, location, and extent of radiological and chemical contamination within the facility to allow decommissioning planning. This guide amplifies guidance regarding facility characterization indicated in ASTM Standard E 1281 on Nuclear Facility Decommissioning Plans. This guide does not address the methodology necessary to release a facility or site for unconditional use. This guide specifically addresses: 1.1.1 the data quality objective for characterization as an initial step in decommissioning planning. 1.1.2 sampling methods, 1.1.3 the logic involved (statistical design) to ensure adequate characterization for decommissioning purposes; and 1.1.4 essential documentation of the characterization information. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate saf...

  15. Potential Benefits to the Philippines of a Nuclear Facility

    Asuncion-Astronomo, A.; Romallosa, K.M.D.; Olivares, R.U.

    2015-01-01

    During the late 1950’s, the Philippines was one of the many countries which began the pursuit of the beneficial applications of atomic energy. With the commissioning of the first Philippine Research Reactor (PRR-1) which attained its first criticality in 1963, our country had the capability for radioisotope production, activation analysis of materials, irradiation studies and various opportunities for basic and applied nuclear science research. The Nuclear Power Plant (PNNP-1) in training plant operators and regulators for the first Philippine Nuclear Power Plant (PNPP-1) in Bataan, which was eventually mothballed in 1986. It is thus unfortunate that the only operating nuclear facility in the country, the PRR-1 encountered technical problems during an upgrade and was shut down in 1988. The problem was not resolved and eventually led to the decommissioning of the PRR-1 in 2005. Without an operating nuclear facility available in the country, the number of personnel knowledgeable and skilled in reactor and nuclear science and engineering has greatly declined and lagged behind our counterparts. This has been the situation for more than two decaded and can only be addressed if the country decides to put up a new nuclear facility. It is acknowledged that putting up a nuclear facility is a major undertaking which requires careful planning, preparation and investment. Thus, a decision by any country to embark on this poster, we will provide an overview of the many potential benefits as well as challenges of establishing a new research reactor and/or accelerator facility in the country. The global distribution, comparisons, capabilities and the different application of these facilities will presented as well.(author)

  16. Emergency Mitigating Equipments - Post Fukushima Actions at Canadian Nuclear Power Plants - Portable AC Power Sources

    Vucetic, Jasmina; Kameswaran, R.

    2015-01-01

    In response to the Fukushima Daiichi NPP accident in 2011, the Canadian Nuclear Safety Commission set up a Task Force to evaluate operational, technical and regulatory implications on Canadian NPPs. While accepting that the risk from beyond-design-basis accidents (BDBA) at Canadian NPPs is very low, the Task Force identified a number of areas where additional improvements or confirmatory assessments would further enhance safety. As a result, a set of 36 Fukushima Action Items (FAIs) were assigned to the licensees. This paper focuses on the FAI related to electrical power system enhancements to address a total loss of all AC Power leading to a possibility of loss of heat sinks (i.e. Station Blackout). This required the licensees to implement the following: - Additional back up power supplied by portable diesel generator(s) to allow key instrumentation and control equipment and key electrical loads to remain operable; - Provisions for a storage and timely transportation and connection of the portable generator(s) to the applicable units; - Provisions for testing of the portable generator; - Provisions for fuelling of portable generators; - Provisions such as panels, receptacles, and connectors to quickly deploy the portable generators to plant system, and separate feeder cables route to avoid a common mode failure; - Load shedding strategy to extend the existing station's battery life to ensure that the connection of portable generators can be completed before the batteries are depleted; - Provisions to supply water to steam generators and Irradiated Fuel Bay using portable pumps; The paper will also provide a brief description of Electrical power systems of the Canadian NPPs designed to satisfy the high safety and reliability requirements for nuclear systems, which are based on the following: - 2 group design philosophy (Group 1 and Group 2 Electrical Power Systems) - 2 separate groups of onsite emergency generators (Class III Standby generators and Emergency

  17. Applying new safeguards technology to existing nuclear facilities

    Johnson, C.E.; Wagner, E.P.

    1979-01-01

    The application and operation of safeguards instrumentation in a facility containing special nuclear material is most successful when the installation is designed for the operation of the specific facility. Experience at the Idaho National Engineering Laboratory demonstrates that installation designs must consider both Safeguards and Production requirements of specific facilities. Equipment selection and installation design influenced by the training and experience of production operations and safeguards personnel at a specific facility help assure successful installation, reliable operation, and minimal operator training. This minimizes impacts on existing plant production activities while maximizing utility of the safeguards information obtained

  18. Applying new safeguards technology to existing nuclear facilities

    Harris, W.J.; Wagner, E.P.

    1979-01-01

    The application and operation of safeguards instrumentation in a facility containing special nuclear material is most successful when the installation is desinged for the operation of the specific facility. Experience at the Idaho National Engineering Laboratory demonstrates that installation designs must consider both safeguards and production requirements of specific facilities. Equipment selection and installation design influenced by the training and experience of production operations and safeguards personnel at a specific facility help assure successful installation, reliable operation, and minimal operator training. This minimizes impacts on existing plant production activities while maximizing utility of the safeguards information obtained

  19. Siting of nuclear facilities. Selections from Nuclear Safety

    Buchanan, J.R.

    1976-07-01

    The report presented siting policy and practice for nuclear power plants as developed in the U.S. and abroad. Twenty-two articles from Nuclear Safety on this general topic are reprinted since they provide a valuable reference source. The appendices also include reprints of some relevant regulatory rules and guides on siting. Advantages and disadvantages of novel siting concepts such as underground containment, offshore siting, and nuclear energy parks are addressed. Other topics include site criteria, risk criteria, and nuclear ship criteria

  20. Siting of nuclear facilities. Selections from Nuclear Safety

    Buchanan, J.R.

    1976-07-01

    The report presented siting policy and practice for nuclear power plants as developed in the U.S. and abroad. Twenty-two articles from Nuclear Safety on this general topic are reprinted since they provide a valuable reference source. The appendices also include reprints of some relevant regulatory rules and guides on siting. Advantages and disadvantages of novel siting concepts such as underground containment, offshore siting, and nuclear energy parks are addressed. Other topics include site criteria, risk criteria, and nuclear ship criteria.

  1. Overview of nuclear data measurement facilities in OECD countries

    Bioux, P.; Rowlands, J.L.

    1996-06-01

    In 1992 EDF commissioned a review of activity in the fields of nuclear data for fission power technology applications in OECD countries. The review was carried out in cooperation with the consultants EUROGRAM. This paper presents a summary. The situation is of concern to the French nuclear industry because of the few measurement facilities which are now funded for work in the field and the reductions in the numbers of scientists expert in measurement and evaluation of nuclear data. There are requirements which justify work to improve knowledge of many items of nuclear data. To ensure maintenance of expertise the French Nuclear Industry has arranged for several young scientists to work with leading experts in the different fields. However, the problem of continued availability of facilities remains. (authors)

  2. Enhancing quality of construction on nuclear facilities

    Buchert, K.P.

    1984-01-01

    From the author's viewpoint and the viewpoint of others, the quality of construction on both nuclear projects and many other non-nuclear projects has decreased. The trend toward recent QA and QC methods of contractors doing their own inspection has not only tended to reduce the quality of construction, but also has discouraged qualified inspectors from accepting positions where this type of QA and QC is practiced. In addition, the methods have decreased the desired interaction between design engineers and construction management. The paper contains detailed recommendations on how the quality of construction can be enhanced on nuclear projects. It is also shown that construction quality must be obtained by different methods than those used to obtain manufacturing quality

  3. Public attitudes toward nuclear generating facilities: positive

    Krannich, R.S.

    1977-01-01

    Public opposition and intervention in the siting and development of nuclear power plants has become more of a limiting factor than technological issues. Attitude surveys indicate that, while the majority of Americans support nuclear power, the utilities would do well to respond to the concerns and opinions of local residents when projects are in the planning stages. Recent polls are analyzed to identify the demographic and perceptive factors of opposition. Demographic studies indicate that the greatest opposition comes from women, young people, urban residents, farmers, low-income groups, and the unemployed. Perceptual opposition is associated with anticipated negative impacts in the form of hazards and social disruption. Since there appears to be a correlation between access to pertinent information and level of support, utility planners could develop educational programs to provide this information on the advantages of nuclear power. 10 references

  4. Forest die-back from nuclear facilities?

    Metzner, H.

    1985-09-01

    A discussion of the mapping method developed by Reichelt is followed by an inquiry into possible correlations between forest decline and natural/man-made radioactivity. To this end, plant damage in areas with unusually high radioactivity as well as in and near nuclear test areas are evaluated; vegetation damage levels near nuclear installations is also evaluated, and the effects of reactor accidents on vegetation studied. To investigate the influence of nuclear power and reprocessing plants, their emissions in rare-gas isotopes as well as in the contaminants SO 2 , NO 2 , O 3 , etc. and the possible effects on meteorological factors and the formation of photooxidants were evaluated. An essential part of the study is concerned with the isotope effects of hydrogen, particularly of released deuterium (865 bibliographical references). (DG) [de

  5. Methodology for categorization of nuclear material in pyroprocessing facility

    Lee, Chanki; Choi, Sungyeol [UNIST, Ulsan (Korea, Republic of); Kim, Woo Jin; Kim, Min Su; Jeong, Yon Hong [Korea Institute of Nuclear Nonproliferation and Control, Daejeon (Korea, Republic of)

    2016-10-15

    For the pyroprocessing facility to be commercialized in future, current regulations should be evaluated and developed in advance, based on the new types of nuclear materials in the facility. Physical protection system, especially, requires reasonable and reliable categorization of nuclear materials, to prevent from the theft of nuclear materials. In this paper, therefore, current categorization methods of nuclear material are investigated and applied to the pyroprocessing facility. After inconsistencies and gaps are found among methods, they are compared and discussed based on eight considering points (i.e, degrees of attractiveness, levels of category, discount factor, physical barriers, chemical barriers, isotopic barriers, radiological barriers, and capabilities of adversaries), to roughly suggest a new method for categorization. Current categorization methods of nuclear material, including IAEA's INFCIRC/225, U.S. DOE's method, newly expected U.S. NRC's method, FOM, and Bunn's approach, are different and can bring inconsistencies of physical protection requirements. The gap among methods will be significant if advanced fuel cycles are applied to them for the future. For example, the categorization results of 5 target materials in pyroprocessing facility show clear inconsistencies, while TRU ingot is considered the most attractive material. To resolve inconsistencies, it is necessary to determine new method suitable to pyroproessing facility, by considering the effects of eight points (i.e, degrees of attractiveness, levels of category, discount factor, physical barriers, chemical barriers, isotopic barriers, radiological barriers, and capabilities of adversaries)

  6. Methodology for categorization of nuclear material in pyroprocessing facility

    Lee, Chanki; Choi, Sungyeol; Kim, Woo Jin; Kim, Min Su; Jeong, Yon Hong

    2016-01-01

    For the pyroprocessing facility to be commercialized in future, current regulations should be evaluated and developed in advance, based on the new types of nuclear materials in the facility. Physical protection system, especially, requires reasonable and reliable categorization of nuclear materials, to prevent from the theft of nuclear materials. In this paper, therefore, current categorization methods of nuclear material are investigated and applied to the pyroprocessing facility. After inconsistencies and gaps are found among methods, they are compared and discussed based on eight considering points (i.e, degrees of attractiveness, levels of category, discount factor, physical barriers, chemical barriers, isotopic barriers, radiological barriers, and capabilities of adversaries), to roughly suggest a new method for categorization. Current categorization methods of nuclear material, including IAEA's INFCIRC/225, U.S. DOE's method, newly expected U.S. NRC's method, FOM, and Bunn's approach, are different and can bring inconsistencies of physical protection requirements. The gap among methods will be significant if advanced fuel cycles are applied to them for the future. For example, the categorization results of 5 target materials in pyroprocessing facility show clear inconsistencies, while TRU ingot is considered the most attractive material. To resolve inconsistencies, it is necessary to determine new method suitable to pyroproessing facility, by considering the effects of eight points (i.e, degrees of attractiveness, levels of category, discount factor, physical barriers, chemical barriers, isotopic barriers, radiological barriers, and capabilities of adversaries)

  7. Nuclear criticality safety program at the Fuel Cycle Facility

    Lell, R.M.; Fujita, E.K.; Tracy, D.B.; Klann, R.T.; Imel, G.R.; Benedict, R.W.; Rigg, R.H.

    1994-01-01

    The Fuel Cycle Facility (FCF) is designed to demonstrate the feasibility of a novel commercial-scale remote pyrometallurgical process for metallic fuels from liquid metal-cooled reactors and to show closure of the Integral Fast Reactor (IFR) fuel cycle. Requirements for nuclear criticality safety impose the most restrictive of the various constraints on the operation of FCF. The upper limits on batch sizes and other important process parameters are determined principally by criticality safety considerations. To maintain an efficient operation within appropriate safety limits, it is necessary to formulate a nuclear criticality safety program that integrates equipment design, process development, process modeling, conduct of operations, a measurement program, adequate material control procedures, and nuclear criticality analysis. The nuclear criticality safety program for FCF reflects this integration, ensuring that the facility can be operated efficiently without compromising safety. The experience gained from the conduct of this program in the Fuel cycle Facility will be used to design and safely operate IFR facilities on a commercial scale. The key features of the nuclear criticality safety program are described. The relationship of these features to normal facility operation is also described

  8. Decommissioning of nuclear facilities: 'it can and has been done'

    2009-01-01

    Considerable international experience gained over the last 20 years demonstrates that nuclear facilities can be safely dismantled and decommissioned once a decision is made to cease operations and permanently shut them down. The term decommissioning is used to describe all the management and technical actions associated with ceasing operation of a nuclear installation and its subsequent dismantling to facilitate its removal from regulatory control (de-licensing). These actions involve decontamination of structures and components, dismantling of components and demolition of buildings, remediation of any contaminated ground and removal of the resulting waste. Worldwide, of the more than 560 commercial nuclear power plants that are or have been in operation, about 120 plants have been permanently shut down and are at some stage of decommissioning. About 10% of all shutdown plants have been fully decommissioned, including eight reactors of more than 100 MWe. A larger number of various types of fuel cycle and research facilities have also been shut down and decommissioned, including: facilities for the extraction and enrichment of uranium, facilities for fuel fabrication and reprocessing, laboratories, isotope production facilities and particle accelerators. This brochure looks at decommissioning across a spectrum of nuclear facilities and shows worldwide examples of successful projects. Further information can be found in NEA publications and on a number of web-sites

  9. Prospective needs for decommissioning commercial nuclear facilities

    Stevens, G.H.; Yasui, M.; Laraia, M.

    1992-01-01

    The answers to the questions: How many reactors will face the end of their operating lifetime over the next few decades? To what extent are the issues of decommissioning urgent? The answers will lead us to those issues that should be tackled now in order to complete smoothly the decommissioning of commercial nuclear power plants. The prospective needs for decommissioning of nuclear power plants are illustrated from the viewpoint of reactor age, and some of the issues to be tackled, in particular by governments, in this century are discussed, to prepare for the future decommissioning activities. (author) 18 refs.; 2 figs.; 2 tabs

  10. Dismantlement and Radioactive Waste Management of DPRK Nuclear Facilities

    Jooho, W.; Baldwin, G.T.

    2005-01-01

    One critical aspect of any denuclearization of the Democratic People's Republic of Korea (DPRK) involves dismantlement of its nuclear facilities and management of their associated radioactive wastes. The decommissioning problem for its two principal operational plutonium facilities at Yongbyun, the 5MWe nuclear reactor and the Radiochemical Laboratory reprocessing facility, alone present a formidable challenge. Dismantling those facilities will create radioactive waste in addition to existing inventories of spent fuel and reprocessing wastes. Negotiations with the DPRK, such as the Six Party Talks, need to appreciate the enormous scale of the radioactive waste management problem resulting from dismantlement. The two operating plutonium facilities, along with their legacy wastes, will result in anywhere from 50 to 100 metric tons of uranium spent fuel, as much as 500,000 liters of liquid high-level waste, as well as miscellaneous high-level waste sources from the Radiochemical Laboratory. A substantial quantity of intermediate-level waste will result from disposing 600 metric tons of graphite from the reactor, an undetermined quantity of chemical decladding liquid waste from reprocessing, and hundreds of tons of contaminated concrete and metal from facility dismantlement. Various facilities for dismantlement, decontamination, waste treatment and packaging, and storage will be needed. The shipment of spent fuel and liquid high level waste out of the DPRK is also likely to be required. Nuclear facility dismantlement and radioactive waste management in the DPRK are all the more difficult because of nuclear nonproliferation constraints, including the call by the United States for 'complete, verifiable and irreversible dismantlement,' or 'CVID.' It is desirable to accomplish dismantlement quickly, but many aspects of the radioactive waste management cannot be achieved without careful assessment, planning and preparation, sustained commitment, and long completion times

  11. Identification of Vital Areas at Nuclear Facilities. Technical Guidance

    2012-01-01

    The possibility that nuclear or other radioactive material could be used for malicious purposes cannot be ruled out in the current global situation. States have responded to this risk by engaging in a collective commitment to strengthen the protection and control of such material and to effectively respond to nuclear security events. States have agreed to strengthen existing and established new international legal instruments to enhance nuclear security around the world. Nuclear security is fundamental in the management of nuclear technologies and in applications where nuclear or other radioactive material is used or transported. Through its nuclear security programme, the IAEA supports States to establish, maintain and sustain an effective nuclear security regime. The IAEA has adopted a comprehensive approach to nuclear security. This recognizes that an effective national nuclear security regime builds on: the implementation of relevant international legal instruments; information protection; physical protection; material accounting and control; detection of and response to trafficking in such material; national response plans; and contingency measures. With its nuclear security series, the IAEA aims to assist States to implement and sustain such a regime in a coherent and integrated manner. The IAEA Nuclear Security Series comprises: Nuclear Security Fundamentals, which include objectives and essential elements of a State?s nuclear security regime; Recommendations; Implementing Guides; and Technical Guidance publications. Each State carries the full responsibility for nuclear security, i.e. to provide for the security of nuclear and other radioactive material and associated facilities and activities; to ensure the security of such material in use, storage or in transport; and to combat illicit trafficking and the inadvertent movement of such material. It should also be prepared to respond to a nuclear security event. The IAEA recommendations for the protection of

  12. Nuclear Fuel Cycle Information System. A directory of nuclear fuel cycle facilities. 2009 ed

    2009-04-01

    The Nuclear Fuel Cycle Information System (NFCIS) is an international directory of civilian nuclear fuel cycle facilities, published online as part of the Integrated Nuclear Fuel Cycle Information System (iNFCIS: http://www-nfcis.iaea.org/). This is the fourth hardcopy publication in almost 30 years and it represents a snapshot of the NFCIS database as of the end of 2008. Together with the attached CD-ROM, it provides information on 650 civilian nuclear fuel cycle facilities in 53 countries, thus helping to improve the transparency of global nuclear fuel cycle activities

  13. Nuclear Security Management for Research Reactors and Related Facilities

    2016-03-01

    This publication provides a single source guidance to assist those responsible for the implementation of nuclear security measures at research reactors and associated facilities in developing and maintaining an effective and comprehensive programme covering all aspects of nuclear security on the site. It is based on national experience and practices as well as on publications in the field of nuclear management and security. The scope includes security operations, security processes, and security forces and their relationship with the State’s nuclear security regime. The guidance is provided for consideration by States, competent authorities and operators

  14. Structural integrity monitoring of critical components in nuclear facilities

    Roth, Maria; Constantinescu, Dan Mihai; Brad, Sebastian; Ducu, Catalin; Malinovschi, Viorel

    2007-01-01

    Full text: The paper presents the results obtained as part of the Project 'Integrated Network for Structural Integrity Monitoring of Critical Components in Nuclear Facilities', RIMIS, a research work underway within the framework of the Ministry of Education and Research Programme 'Research of Excellence'. The main objective of the Project is to constitute a network integrating the national R and D institutes with preoccupations in the structural integrity assessment of critical components in the nuclear facilities operating in Romania, in order to elaborate a specific procedure for this field. The degradation mechanisms of the structural materials used in the CANDU type reactors, operated by Unit 1 and Unit 2 at Cernavoda (pressure tubes, fuel elements sheaths, steam generator tubing) and in the nuclear facilities relating to reactors of this type as, for instance, the Hydrogen Isotopes Separation facility, will be investigated. The development of a flexible procedure will offer the opportunity to extend the applications to other structural materials used in the nuclear field and in the non-nuclear fields as well, in cooperation with other institutes involved in the developed network. The expected results of the project will allow the integration of the network developed at national level in the structures of similar networks operating within the EU, the enhancement of the scientific importance of Romanian R and D organizations as well as the increase of our country's contribution in solving the major issues of the nuclear field. (authors)

  15. Decommissioning and environmental restoration of nuclear facilities in China

    Pan Ziqiang

    2000-01-01

    In the beginning of the 1980s, the Scientific and Technological Commission (STC) began the study on the environmental impact of the nuclear industry in China. At the end of the 1980s, the STC initiated the study on the decommissioning of nuclear facilities and environmental restoration. In 1989 the STC completed the project entitled ''Radiological and Environmental Quality Assessment of the Nuclear Industry in China Over the Past Thirty Years''. The status of the environmental pollution of various nuclear facility sites was subsequently analysed. In 1994, the decommissioning and environmental restoration of the first research and manufacture complex for nuclear weapons was completed. The complex is now accessible to the public without restriction and the site has become a town. Some nuclear related facilities, such as uranium mines, are currently being decommissioned. Although uranium mining and milling has a more serious impact on the environment, the technology for decommissioning and environmental restoration in mining and milling installations is not much more complicated than that used for reactor and reprocessing facilities: much has been achieved in the area of mining and milling. (author)

  16. Laboratory instrumentation modernization at the WPI Nuclear Reactor Facility

    1995-01-01

    With partial funding from the Department of Energy (DOE) University Reactor Instrumentation Program several laboratory instruments utilized by students and researchers at the WPI Nuclear Reactor Facility have been upgraded or replaced. Designed and built by General Electric in 1959, the open pool nuclear training reactor at WPI was one of the first such facilities in the nation located on a university campus. Devoted to undergraduate use, the reactor and its related facilities have been since used to train two generations of nuclear engineers and scientists for the nuclear industry. The low power output of the reactor and an ergonomic facility design make it an ideal tool for undergraduate nuclear engineering education and other training. The reactor, its control system, and the associate laboratory equipment are all located in the same room. Over the years, several important milestones have taken place at the WPI reactor. In 1969, the reactor power level was upgraded from 1 kW to 10 kW. The reactor's Nuclear Regulatory Commission operating license was renewed for 20 years in 1983. In 1988, under DOE Grant No. DE-FG07-86ER75271, the reactor was converted to low-enriched uranium fuel. In 1992, again with partial funding from DOE (Grant No. DE-FG02-90ER12982), the original control console was replaced

  17. Decommissioning of nuclear facilities. Feasibility, needs and costs

    1986-01-01

    Reactor decommissioning activities generally are considered to begin after operations have ceased and the fuel has been removed from the reactor, although in some countries the activities may be started while the fuel is still at the reactor site. The three principal alternatives for decommissioning are described. The factors to be considered in selecting the decommissioning strategy, i.e. a stage or a combination of stages that comprise the total decommissioning programme, are reviewed. One presents a discussion of the feasibility of decommissioning techniques available for use on the larger reactors and fuel cycle facilities. The numbers and types of facilities to be decommissioned and the resultant waste volumes generated for disposal will then be projected. Finally, the costs of decommissioning these facilities, the effect of these costs on electricity generating costs, and alternative methods of financing decommissioning are discussed. The discussion of decommissioning draws on various countries' studies and experience in this area. Specific details about current activities and policies in NEA Member Countries are given in the short country specific Annexes. The nuclear facilities that are addressed in this study include reactors, fuel fabrication facilities, reprocessing facilities, associated radioactive waste storage facilities, enrichment facilities and other directly related fuel cycle support facilities. The present study focuses on the technical feasibility, needs, and costs of decommissioning the larger commercial facilities in the OECD member countries that are coming into service up to the year 2000. It is intended to inform the public and to assist in planning for the decommissioning of these facilities

  18. ISOL based radioactive nuclear beam facilities

    Nomura, T.

    1991-07-01

    High-intensity and high-quality unstable nuclear beams can be realized by coupling an isotope separator on-line and a proper post accelerator in various primary beams. Some technical features and problems in the production of such beams are discussed. A brief description is given on 'Exotic Nuclei Arena' in Japanese Hadron Project. (author)

  19. Computer Security at Nuclear Facilities. Reference Manual (Arabic Edition)

    2011-01-01

    The possibility that nuclear or other radioactive material could be used for malicious purposes cannot be ruled out in the current global situation. States have responded to this risk by engaging in a collective commitment to strengthen the protection and control of such material and to respond effectively to nuclear security events. States have agreed to strengthen existing instruments and have established new international legal instruments to enhance nuclear security worldwide. Nuclear security is fundamental in the management of nuclear technologies and in applications where nuclear or other radioactive material is used or transported. Through its Nuclear Security Programme, the IAEA supports States to establish, maintain and sustain an effective nuclear security regime. The IAEA has adopted a comprehensive approach to nuclear security. This recognizes that an effective national nuclear security regime builds on: the implementation of relevant international legal instruments; information protection; physical protection; material accounting and control; detection of and response to trafficking in such material; national response plans; and contingency measures. With its Nuclear Security Series, the IAEA aims to assist States in implementing and sustaining such a regime in a coherent and integrated manner. The IAEA Nuclear Security Series comprises Nuclear Security Fundamentals, which include objectives and essential elements of a State's nuclear security regime; Recommendations; Implementing Guides; and Technical Guidance. Each State carries the full responsibility for nuclear security, specifically: to provide for the security of nuclear and other radioactive material and associated facilities and activities; to ensure the security of such material in use, storage or in transport; to combat illicit trafficking and the inadvertent movement of such material; and to be prepared to respond to a nuclear security event. This publication is in the Technical Guidance

  20. Computer Security at Nuclear Facilities. Reference Manual (Russian Edition)

    2012-01-01

    The possibility that nuclear or other radioactive material could be used for malicious purposes cannot be ruled out in the current global situation. States have responded to this risk by engaging in a collective commitment to strengthen the protection and control of such material and to respond effectively to nuclear security events. States have agreed to strengthen existing instruments and have established new international legal instruments to enhance nuclear security worldwide. Nuclear security is fundamental in the management of nuclear technologies and in applications where nuclear or other radioactive material is used or transported. Through its Nuclear Security Programme, the IAEA supports States to establish, maintain and sustain an effective nuclear security regime. The IAEA has adopted a comprehensive approach to nuclear security. This recognizes that an effective national nuclear security regime builds on: the implementation of relevant international legal instruments; information protection; physical protection; material accounting and control; detection of and response to trafficking in such material; national response plans; and contingency measures. With its Nuclear Security Series, the IAEA aims to assist States in implementing and sustaining such a regime in a coherent and integrated manner. The IAEA Nuclear Security Series comprises Nuclear Security Fundamentals, which include objectives and essential elements of a State's nuclear security regime; Recommendations; Implementing Guides; and Technical Guidance. Each State carries the full responsibility for nuclear security, specifically: to provide for the security of nuclear and other radioactive material and associated facilities and activities; to ensure the security of such material in use, storage or in transport; to combat illicit trafficking and the inadvertent movement of such material; and to be prepared to respond to a nuclear security event. This publication is in the Technical Guidance