WorldWideScience

Sample records for californium iodides

  1. Potassium Iodide

    Science.gov (United States)

    Potassium iodide is used to protect the thyroid gland from taking in radioactive iodine that may be released ... damage the thyroid gland. You should only take potassium iodide if there is a nuclear radiation emergency and ...

  2. Californium Electrodepositions at Oak Ridge National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Boll, Rose Ann [ORNL

    2015-01-01

    Electrodepositions of californium isotopes were successfully performed at Oak Ridge National Laboratory (ORNL) during the past year involving two different types of deposition solutions, ammonium acetate (NH4C2H3O2) and isobutanol ((CH3)2CHCH2OH). A californium product that was decay enriched in 251Cf was recovered for use in super-heavy element (SHE) research. This neutron-rich isotope, 251Cf, provides target material for SHE research for the potential discovery of heavier isotopes of Z=118. The californium material was recovered from aged 252Cf neutron sources in storage at ORNL. These sources have decayed for over 30 years, thus providing material with a very high 251Cf-to-252Cf ratio. After the source capsules were opened, the californium was purified and then electrodeposited using the isobutanol method onto thin titanium foils for use in an accelerator at the Joint Institute for Nuclear Research in Dubna, Russia. Another deposition method, ammonium acetate, was used to produce a deposition containing 1.7 0.1 Ci of 252Cf onto a stainless steel substrate. This was the largest single electrodeposition of 252Cf ever prepared. The 252Cf material was initially purified using traditional ion exchange media, such as AG50-AHIB and AG50-HCl, and further purified using a TEVA-NH4SCN system to remove any lanthanides, resulting in the recovery of 3.6 0.1 mg of purified 252Cf. The ammonium acetate deposition was run with a current of 1.0 amp, resulting in a 91.5% deposition yield. Purification and handling of the highly radioactive californium material created additional challenges in the production of these sources.

  3. Historical Review of Californium-252 Discovery and Development

    Science.gov (United States)

    Stoddard, D. H.

    1985-01-01

    This paper discusses the discovery and history of californium 252. This isotope may be synthesized by irradiating plutonium 239, plutonium 242, americium 243, or curium 244 with neutrons in a nuclear reactor. Various experiments and inventions involving Cf conducted at the Savannah River Plant are discussed. The evolution of radiotherapy using californium 252 is reviewed. (PLG)

  4. Potassium Iodide (KI)

    Science.gov (United States)

    ... Health Matters Information on Specific Types of Emergencies Potassium Iodide (KI) Language: English Español (Spanish) Recommend on Facebook ... can I get KI (potassium iodide)? What is Potassium Iodide (KI)? KI (potassium iodide) is a salt of ...

  5. Production, Distribution, and Applications of Californium-252 Neutron Sources

    Energy Technology Data Exchange (ETDEWEB)

    Balo, P.A.; Knauer, J.B.; Martin, R.C.

    1999-10-03

    The radioisotope {sup 252}Cf is routinely encapsulated into compact, portable, intense neutron sources with a 2.6-year half-life. A source the size of a person's little finger can emit up to 10{sup 11} neutrons/s. Californium-252 is used commercially as a reliable, cost-effective neutron source for prompt gamma neutron activation analysis (PGNAA) of coal, cement, and minerals, as well as for detection and identification of explosives, laud mines, and unexploded military ordnance. Other uses are neutron radiography, nuclear waste assays, reactor start-up sources, calibration standards, and cancer therapy. The inherent safety of source encapsulations is demonstrated by 30 years of experience and by U.S. Bureau of Mines tests of source survivability during explosions. The production and distribution center for the U. S Department of Energy (DOE) Californium Program is the Radiochemical Engineering Development Center (REDC) at Oak Ridge National Laboratory (ORNL). DOE sells The radioisotope {sup 252}Cf is routinely encapsulated into compact, portable, intense neutron sources with a 2.6- year half-life. A source the size of a person's little finger can emit up to 10 neutrons/s. Californium-252 is used commercially as a reliable, cost-effective neutron source for prompt gamma neutron activation analysis (PGNAA) of coal, cement, and minerals, as well as for detection and identification of explosives, laud mines, and unexploded military ordnance. Other uses are neutron radiography, nuclear waste assays, reactor start-up sources, calibration standards, and cancer therapy. The inherent safety of source encapsulations is demonstrated by 30 years of experience and by U.S. Bureau of Mines tests of source survivability during explosions. The production and distribution center for the U. S Department of Energy (DOE) Californium Program is the Radiochemical Engineering Development Center (REDC) at Oak Ridge National Laboratory(ORNL). DOE sells {sup 252}Cf to commercial

  6. dl-Alaninium iodide

    Directory of Open Access Journals (Sweden)

    Kevin Lamberts

    2012-06-01

    Full Text Available The crystal structure of dl-alanine hydroiodide (1-carboxyethanaminium iodide, C3H8NO2+·I−, is that of an organic salt consisting of N-protonated cations and iodide anions. The compound features homochiral helices of N—H...O hydrogen-bonded cations in the [010] direction; neighbouring chains are related by crystallographic inversion centers and hence show opposite chirality. The iodide counter-anions act as hydrogen-bond acceptors towards H atoms of the ammonium and carboxy groups, and cross-link the chains along [100]. Thus, an overall two-dimensional network is formed in the ab plane. No short contacts occur between iodide anions.

  7. Teratogenic effect of Californium-252 irradiation in rats

    Energy Technology Data Exchange (ETDEWEB)

    Satow, Yukio; Lee, Juing-Yi; Hori, Hiroshi; Okuda, Hiroe; Tsuchimoto, Shigeo; Sawada, Shozo; Yokoro, Kenjiro (Hiroshima Univ. (Japan). Research Inst. for Nuclear Medicine and Biology)

    1989-06-01

    The teratogenicity of Californium-252 (Cf-252) irradiation which generates approximately 70% 2.3 MeV fast neutron and 30% gamma rays was evaluated. A single whole body exposure of Cf-252 at various doses was given to pregnant rats on day 8 or 9 of pregnancy, followed by microscopic autopsy of the fetuses at the terminal stage of pregnancy to search for external and internal malformations. For comparison, pregnant rats were irradiated with various doses of Cobalt-60 (Co-60) standard gamma rays at the same dose rate (1 rad/min.). The doses were 20-120 rad of Cf-252 and 80-220 rad of Co-60. Using frequency of radiation induced malformations observed on day 8 of pregnancy as an index, relative biological effectiveness (RBE) of 2.3-2.7 was obtained from the straight line obtained by modifying by the least squares method the frequency curves of malformed fetuses in total implants and in surviving fetuses. The types of malformations induced by Cf-252 and Co-60 irradiation were alike. Using fetal LD/sub 50/ as an index, 2.4 was obtained as RBE when irradiated on day 8 of pregnancy and 3.1 as that when irradiated on day 9. The results showed that Cf-252 had stronger a teratogenic effect than Co-60 gamma rays. (author).

  8. 21 CFR 184.1265 - Cuprous iodide.

    Science.gov (United States)

    2010-04-01

    ... with potassium iodide under slightly acidic conditions. (b) The ingredient must be of a purity suitable... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Cuprous iodide. 184.1265 Section 184.1265 Food and... Substances Affirmed as GRAS § 184.1265 Cuprous iodide. (a) Cuprous iodide (copper (I) iodide, CuI, CAS...

  9. Synthesis of mercuric iodide and bismuth tri-iodide nanoparticles for heavy metal iodide films nucleation

    Energy Technology Data Exchange (ETDEWEB)

    Fornaro, L.; Pereira, H.Bentos [Compound Semiconductors Group, CURE, Universidad de la Republica, Rocha (Uruguay); Aguiar, I.; Perez Barthaburu, M. [Compound Semiconductors Group, Facultad de Quimica, Univ. de la Republica, Montevideo (Uruguay)

    2011-12-15

    We synthesized mercuric iodide and bismuth tri-iodide nanoparticles by suspension in octadecene, from Hg(NO{sub 3}){sub 2}.H{sub 2}O and I{sub 2}, and from Bi(NO{sub 3}){sub 3}.5H{sub 2}O and I{sub 2}, respectively. The best synthesis conditions were 2 h at 70-80 C, followed by 10 min at 110 C for mercuric iodide nanoparticles, and 4 h at 80-110 C, followed by 10 min at 180-210 C for bismuth tri-iodide ones. Nanoparticles were then washed and centrifuged with ether repeatedly. Compounds identity was confirmed by X-ray diffraction (XRD) and energy dispersive spectrometry (EDS). We found shifts of the X-ray diffraction maxima for nanoparticles of both compounds. We characterized the nanoparticles by transmission (TEM) and scanning (SEM) electron microscopy. We obtained disk-like and squared mercuric iodide nanostructures, 80-140 nm and 100-125 nm in size respectively. We also obtained rounded and rod-like bismuth tri-iodide nanoparticles, 30-500 nm in size. Acetonitrile and isopropanol suspensions of mercuric iodide nanoparticles, and acetonitrile suspension of bismuth tri-iodide nanoparticles exhibited peak maxima shifts in their UV-Vis spectra. We synthesized for the first time mercuric iodide and bismuth tri-iodide nanoparticles by the suspension method, although we have not yet obtained uniform shape and size distributions. They offer interesting perspectives for crystalline film nucleation and for improving current applications of these materials, as well as for opening new ones. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  10. 21 CFR 172.375 - Potassium iodide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Potassium iodide. 172.375 Section 172.375 Food and... Dietary and Nutritional Additives § 172.375 Potassium iodide. The food additive potassium iodide may be safely used in accordance with the following prescribed conditions: (a) Potassium iodide may be...

  11. Iodide transport and breast cancer.

    Science.gov (United States)

    Poole, Vikki L; McCabe, Christopher J

    2015-10-01

    Breast cancer is the second most common cancer worldwide and the leading cause of cancer death in women, with incidence rates that continue to rise. The heterogeneity of the disease makes breast cancer exceptionally difficult to treat, particularly for those patients with triple-negative disease. To address the therapeutic complexity of these tumours, new strategies for diagnosis and treatment are urgently required. The ability of lactating and malignant breast cells to uptake and transport iodide has led to the hypothesis that radioiodide therapy could be a potentially viable treatment for many breast cancer patients. Understanding how iodide is transported, and the factors regulating the expression and function of the proteins responsible for iodide transport, is critical for translating this hypothesis into reality. This review covers the three known iodide transporters - the sodium iodide symporter, pendrin and the sodium-coupled monocarboxylate transporter - and their role in iodide transport in breast cells, along with efforts to manipulate them to increase the potential for radioiodide therapy as a treatment for breast cancer.

  12. Apparatus for the measurement of total body nitrogen using prompt neutron activation analysis with californium-252.

    Science.gov (United States)

    Mackie, A; Hannan, W J; Smith, M A; Tothill, P

    1988-01-01

    Details of clinical apparatus designed for the measurement of total body nitrogen (as an indicator of body protein), suitable for the critically ill, intensive-care patient are presented. Californium-252 radio-isotopic neutron sources are used, enabling a nitrogen measurement by prompt neutron activation analysis to be made in 40 min with a precision of +/- 3.2% for a whole body dose equivalent of 0.145 mSv. The advantages of Californium-252 over alternative neutron sources are discussed. A comparison between two irradiation/detection geometries is made, leading to an explanation of the geometry adopted for the apparatus. The choice of construction and shielding materials to reduce the count rate at the detectors and consequently to reduce the pile-up contribution to the nitrogen background is discussed. Salient features of the gamma ray spectroscopy system to reduce spectral distortion from pulse pile-up are presented.

  13. Frequently Asked Questions on Potassium Iodide (KI)

    Science.gov (United States)

    ... Bioterrorism and Drug Preparedness Frequently Asked Questions on Potassium Iodide (KI) Share Tweet Linkedin Pin it More sharing ... Drug Administration (FDA) issued a final Guidance on Potassium Iodide as a Thyroid Blocking Agent in Radiation Emergencies) ( ...

  14. 21 CFR 582.5634 - Potassium iodide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Potassium iodide. 582.5634 Section 582.5634 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5634 Potassium iodide. (a) Product. Potassium iodide. (b) Tolerance. 0.01 percent....

  15. 21 CFR 184.1634 - Potassium iodide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Potassium iodide. 184.1634 Section 184.1634 Food... Specific Substances Affirmed as GRAS § 184.1634 Potassium iodide. (a) Potassium iodide (KI, CAS Reg. No. 7681-11-0) is the potassium salt of hydriodic acid. It occurs naturally in sea water and in...

  16. Spontaneous Partitioning of Californium from Curium: Curious Cases from the Crystallization of Curium Coordination Complexes

    Energy Technology Data Exchange (ETDEWEB)

    Cary, Samantha K.; Silver, Mark A.; Liu, Guokui; Wang, Jamie C.; Bogart, Justin A.; Stritzinger, Jared T.; Arico, Alexandra A.; Hanson, Kenneth; Schelter, Eric J.; Albrecht-Schmitt, Thomas E.

    2015-12-07

    The reaction of 248CmCl3 with excess 2,6-pyridinedicarboxylic acid (DPA) under mild solvothermal conditions results in crystallization of the tris-chelate complex Cm(HDPA)3·H2O. Approximately half of the curium remains in solution at the end of this process, and evaporation of the mother liquor results in crystallization of the bis-chelate complex [Cm(HDPA)- (H2DPA)(H2O)2Cl]Cl·2H2O. 248Cm is the daughter of the α decay of 252Cf and is extracted in high purity from this parent. However, trace amounts of 249,250,251Cf are still present in all samples of 248Cm. During the crystallization of Cm(HDPA)3·H2O and [Cm(HDPA)(H2DPA)(H2O)2Cl]Cl·2H2O, californium(III) spontaneously separates itself from the curium complexes and is found doped within crystals of DPA in the form of Cf(HDPA)3. These results add to the growing body of evidence that the chemistry of californium is fundamentally different from that of earlier actinides.

  17. [Rare, severe hypersensitivity reaction to potassium iodide].

    Science.gov (United States)

    Korsholm, Anne Sofie; Ebbehøj, Eva; Richelsen, Bjørn

    2014-07-07

    The literature reports a large variety of adverse reactions to potassium iodide. A severe hypersensitivity reaction to potassium iodide in a 51-year-old woman with Graves' thyrotoxicosis is described. Following administration the patient developed sialadenitis, conjunctivitis, stomatitis and acneiform iododerma that responded dramatically to withdrawal of the potassium iodide and administration with corticosteroids. Awareness of these adverse reactions may prevent prolonged hospitalization and unnecessary tests and treatments.

  18. Uptake of iodide in the marine haptophyte Isochrysis sp. (T.ISO) driven by iodide oxidation.

    Science.gov (United States)

    van Bergeijk, Stef A; Hernández Javier, Laura; Heyland, Andreas; Manchado, Manuel; Pedro Cañavate, José

    2013-08-01

    Uptake of iodide was studied in the marine microalga Isochrysis sp. (isol. Haines, T.ISO) during short-term incubations with radioactive iodide ((125) I(-) ). Typical inhibitors of the sodium/iodide symporter (NIS) did not inhibit iodide uptake, suggesting that iodide is not taken up through this transport protein, as is the case in most vertebrate animals. Oxidation of iodide was found to be an essential step for its uptake by T.ISO and it seemed likely that hypoiodous acid (HOI) was the form of iodine taken up. Uptake of iodide was inhibited by the addition of thiourea and of other reducing agents, like L-ascorbic acid, L-glutathione and L-cysteine and increased after the addition of oxidized forms of the transition metals Fe and Mn. The simultaneous addition of both hydrogen peroxide (H2 O2 ) and a known iodide-oxidizing myeloperoxidase (MPO) significantly increased iodine uptake, but the addition of H2 O2 or MPO separately, had no effect on uptake. This confirms the observation that iodide is oxidized prior to uptake, but it puts into doubt the involvement of H2 O2 excretion and membrane-bound or extracellular haloperoxidase activity of T.ISO. The increase of iodide uptake by T.ISO upon Fe(III) addition suggests the nonenzymatic oxidation of iodide by Fe(III) in a redox reaction and subsequent influx of HOI. This is the first report on the mechanism of iodide uptake in a marine microalga.

  19. Neutron Detection with Mercuric Iodide

    CERN Document Server

    Bell, Z A

    2003-01-01

    Mercuric iodide is a high-density, high-Z semiconducting material useful for gamma ray detection. This makes it convertible to a thermal neutron detector by covering it with a boron rich material and detecting the 478 keV gamma rays resulting from the sup 1 sup 0 B(n, alpha) sup 7 Li* reaction. However, the 374 barn thermal capture cross section of sup n sup a sup t Hg, makes the detector itself an attractive absorber, and this has been exploited previously. Since previous work indicates that there are no low-energy gamma rays emitted in coincidence with the 368 keV capture gamma from the dominant sup 1 sup 9 sup 9 Hg(n, gamma) sup 2 sup 0 sup 0 Hg reaction, only the 368 keV capture gamma is seen with any efficiency a relatively thin (few mm) detector. In this paper we report preliminary measurements of neutrons via capture reactions in a bare mercuric iodide crystal and a crystal covered in sup 1 sup 0 B-loaded epoxy. The covered detector is an improvement over the bare detector because the presence of both ...

  20. Predissociation dynamics of lithium iodide

    CERN Document Server

    Schmidt, H; Stienkemeier, F; Bogomolov, A S; Baklanov, A V; Reich, D M; Skomorowski, W; Koch, C P; Mudrich, M

    2015-01-01

    The predissociation dynamics of lithium iodide (LiI) in the first excited A-state is investigated for molecules in the gas phase and embedded in helium nanodroplets, using femtosecond pump-probe photoionization spectroscopy. In the gas phase, the transient Li+ and LiI+ ion signals feature damped oscillations due to the excitation and decay of a vibrational wave packet. Based on high-level ab initio calculations of the electronic structure of LiI and simulations of the wave packet dynamics, the exponential signal decay is found to result from predissociation predominantly at the lowest avoided X-A potential curve crossing, for which we infer a coupling constant V=650(20) reciprocal cm. The lack of a pump-probe delay dependence for the case of LiI embedded in helium nanodroplets indicates fast droplet-induced relaxation of the vibrational excitation.

  1. Predissociation dynamics of lithium iodide

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, H.; Vangerow, J. von; Stienkemeier, F.; Mudrich, M., E-mail: mudrich@physik.uni-freiburg.de [Physikalisches Institut, Universität Freiburg, 79104 Freiburg (Germany); Bogomolov, A. S. [Institute of Chemical Kinetics and Combustion, Novosibirsk 630090 (Russian Federation); Baklanov, A. V. [Institute of Chemical Kinetics and Combustion, Novosibirsk 630090 (Russian Federation); Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Reich, D. M.; Skomorowski, W.; Koch, C. P. [Theoretische Physik, Universität Kassel, Heinrich-Plett-Str. 40, 34132 Kassel (Germany)

    2015-01-28

    The predissociation dynamics of lithium iodide (LiI) in the first excited A-state is investigated for molecules in the gas phase and embedded in helium nanodroplets, using femtosecond pump-probe photoionization spectroscopy. In the gas phase, the transient Li{sup +} and LiI{sup +} ion signals feature damped oscillations due to the excitation and decay of a vibrational wave packet. Based on high-level ab initio calculations of the electronic structure of LiI and simulations of the wave packet dynamics, the exponential signal decay is found to result from predissociation predominantly at the lowest avoided X-A potential curve crossing, for which we infer a coupling constant V{sub XA} = 650(20) cm{sup −1}. The lack of a pump-probe delay dependence for the case of LiI embedded in helium nanodroplets indicates fast droplet-induced relaxation of the vibrational excitation.

  2. Clinical Report on Californium-252 Neutron Intraluminal Brachytherapy Combined with External Irradiation for Cervical Carcinoma Treatment

    Institute of Scientific and Technical Information of China (English)

    Huanyu Zhao; Keming Wang; Jian Sun; Xin Geng; Weiming Zhang

    2006-01-01

    OBJECTIVE To observe the curative effects and complications of californium-252 (252Cf) neutron intraluminal brachytherapy (IBT) combined with external irradiation (El) for treatment of cervical carcinoma.METHODS From December 2000 to December 2004, 128 cases of cervical carcinoma staged into ⅡA~ⅢB according to the International Federation of Gynecology and Obstetrics (FIGO) standards were treated with 252Cf neutron IBT using 8~10 Gy per fraction, once a week. The total dose at reference A point was 36~40 Gy in 4~5 fractions. From the second day after 252Cf neutron IBT treatment, the whole pelvic cavity was treated with 60Co γ-ray El, applying 2 Gy per fraction, 4 times per week. After 20~25 Gy of El, the center of the whole pelvic field was blocked with 4 cm of lead in width. The total dose of El was 45~50 Gy.RESULTS The short-term therapeutic effects were CR 95.3% and PR 4.7%. The 3 and 5-year local control rates were 93.5% and 87.9%. The overall 3-year survival rate was 87.5% and for Stages Ⅱ and Ⅲ , 90.9%and 81.5% respectively; the overall 5-year survival rate was 70% and for Stages Ⅱ and Ⅲ, 76.2% and 61% respectively. The rate of radiation complications was 4.7% for radiation cystitis, 7.8% for radiation proctitis, 6.3%for vagina contracture and adhesion and 5.5% for protracted radiation proctitis.CONCLUSION An combination of 252Cf neutron IBT with El for treatment of cervical carcinoma can be well-tolerated by cervical carcinoma patients. The rate of local tumor control is high and radiation complications are few.

  3. Application of TSH bioindicator for studying the biological efficiency of neutrons from californium-252 source

    Energy Technology Data Exchange (ETDEWEB)

    Cebulska-Wasilewska, A.; Rekas, K. [Institute of Nuclear Physics, Cracow (Poland); Kim, J.K. [Korea Atomic Energy Research Inst., Taejon (Korea, Republic of)

    1997-12-31

    The effectiveness of neutrons from a Californium-252 source in the induction of various abnormalities in the Tradescantia clone 4430 stamen hair cells (TSH-assay) was studied. The special attention was paid to check whether any enhancement in effects caused by process of boron neutron capture is visible in the cells enriched with boron ions. Two chemicals (borax and BSH) were applied to introduce boron-10 ions into cells. Inflorescence, normal or pretreated with chemicals containing boron, were irradiated in the air with neutrons from a Cf-252 source at KAERI, Taejon, Korea. To estimate the relative biological effectiveness (RBE) in the induction of gene mutations of the neutron beam under the study, Tradescantia inflorescences, without any chemical pretreatment, were irradiated with various doses of X-rays. The ranges of radiation doses used were 0-0.1 Gy in neutrons and 0-0.5 Gy in X-rays. After the time needed to complete the postirradiation repair Tradescantia cuttings were transferred to Cracow, where screening of gene and lethal; mutations, cell cycle alterations in somatic cells have been done, and dose response relationships were figured. The maximal RBE values were estimated in the range of 4.6-6.8. Alterations of RBE value were observed; from 6.8 to 7.8 in the case of plants pretreated with 240 ppm of B-10 from borax, and 4.6 to 6.1 in the case of 400 ppm of B-10 from BSH. Results showed a slight, although statistically insignificant increase in biological efficacy of radiation from the Cf-252 source in samples pretreated with boron containing chemicals. (author)

  4. Simplest Formula of Copper Iodide: A Stoichiometry Experiment.

    Science.gov (United States)

    MacDonald, D. J.

    1983-01-01

    Describes an experiment presented to students as a problem in determining the stoichiometry of "copper iodide" to decide whether it is cuprous iodide or cupric iodide. The experiment illustrates stoichiometry principles, providing experiences with laboratory techniques and numerical computation. Detailed outline (written for student use) is…

  5. Electrochemical reaction rates in a dye sentisised solar cell - the iodide/tri-iodide redox system

    DEFF Research Database (Denmark)

    Bay, Lasse; West, Keld; Winter-Jensen, Bjørn

    2006-01-01

    The electrochemical reaction rate of the redox couple iodide / tri-iodide in acetonitrile is characterised by impedance spectroscopy. Different electrode materials relevant for the function of dye-sensitised solar cells (DSSC) are investigated. Preferably, the reaction with the iodide / tri......-iodide couple should be fast at the counter electrode, i.e. this electrode must have a high catalytic activity towards the redox couple, and the same reaction must be slow on the photo electrode. The catalytic activity is investigated for platinum, poly(3,4-ethylenedioxythiophene) (PEDOT), polypyrrole (PPy......), and polyaniline (PANI) - all deposited onto fluorine doped tin oxide (FTO) glass. Both Pt and PEDOT are found to have sufficiently high catalytic activities for practical use as counter electrode in DSSC. The reaction resistance on FTO and anatase confirmed the beneficial effect of a compact anatase layer on top...

  6. Barium iodide and strontium iodide crystals andd scintillators implementing the same

    Science.gov (United States)

    Payne, Stephen A; Cherepy, Nerine J; Hull, Giulia E; Drobshoff, Alexander D; Burger, Arnold

    2013-11-12

    In one embodiment, a material comprises a crystal comprising strontium iodide providing at least 50,000 photons per MeV. A scintillator radiation detector according to another embodiment includes a scintillator optic comprising europium-doped strontium iodide providing at least 50,000 photons per MeV. A scintillator radiation detector in yet another embodiment includes a scintillator optic comprising SrI.sub.2 and BaI.sub.2, wherein a ratio of SrI.sub.2 to BaI.sub.2 is in a range of between 0:1 A method for manufacturing a crystal suitable for use in a scintillator includes mixing strontium iodide-containing crystals with a source of Eu.sup.2+, heating the mixture above a melting point of the strontium iodide-containing crystals, and cooling the heated mixture near the seed crystal for growing a crystal. Additional materials, systems, and methods are presented.

  7. Methyl Iodide Fumigation of Bacillus anthracis Spores.

    Science.gov (United States)

    Sutton, Mark; Kane, Staci R; Wollard, Jessica R

    2015-09-01

    Fumigation techniques such as chlorine dioxide, vaporous hydrogen peroxide, and paraformaldehyde previously used to decontaminate items, rooms, and buildings following contamination with Bacillus anthracis spores are often incompatible with materials (e.g., porous surfaces, organics, and metals), causing damage or residue. Alternative fumigation with methyl bromide is subject to U.S. and international restrictions due to its ozone-depleting properties. Methyl iodide, however, does not pose a risk to the ozone layer and has previously been demonstrated as a fumigant for fungi, insects, and nematodes. Until now, methyl iodide has not been evaluated against Bacillus anthracis. Sterne strain Bacillus anthracis spores were subjected to methyl iodide fumigation at room temperature and at 550C. Efficacy was measured on a log-scale with a 6-log reduction in CFUs being considered successful compared to the U.S. Environmental Protection Agency biocide standard. Such efficacies were obtained after just one hour at 55 °C and after 12 hours at room temperature. No detrimental effects were observed on glassware, PTFE O-rings, or stainless steel. This is the first reported efficacy of methyl iodide in the reduction of Bacillus anthracis spore contamination at ambient and elevated temperatures.

  8. Potassium iodide capsule treatment of feline sporotrichosis.

    Science.gov (United States)

    Reis, Erica G; Gremião, Isabella D F; Kitada, Amanda A B; Rocha, Raphael F D B; Castro, Verônica S P; Barros, Mônica B L; Menezes, Rodrigo C; Pereira, Sandro A; Schubach, Tânia M P

    2012-06-01

    Sporotrichosis is a mycosis caused by Sporothrix schenckii. The most affected animal is the cat; it has played an important role in the zoonotic transmission of this disease, especially in Rio de Janeiro, Brazil, since 1998. In order to evaluate the treatment of feline sporotrichosis with potassium iodide, an observational cohort was conducted in 48 cats with sporotrichosis at Instituto de Pesquisa Clínica Evandro Chagas, Fiocruz. All cats received potassium iodide capsules, 2.5 mg/kg to 20 mg/kg q24h. The cure rate was 47.9%, treatment failure was 37.5%, treatment abandonment was 10.4% and death was 4.2%. Clinical adverse effects were observed in 52.1% of the cases. Thirteen cats had a mild increase in hepatic transaminase levels during the treatment, six of them presented clinical signs suggestive of hepatotoxicity. Compared to previous studies with itraconazole and iodide in saturated solution, potassium iodide capsules are an alternative for feline sporotrichosis treatment.

  9. Study of the shielding for spontaneous fission sources of Californium-252; Estudio de blindaje para fuentes de fision espontanea de Californio-252

    Energy Technology Data Exchange (ETDEWEB)

    Davila R, I

    1991-06-15

    A shielding study is made to attenuate, until maximum permissible levels, the neutrons radiation and photons emitted by spontaneous fission coming from a source of Californium-252. The compound package by a database (Library DLC-23) and the ANISNW code is used, in it version for personal computer. (Author)

  10. Atomic force microscopy of lead iodide crystal surfaces

    Science.gov (United States)

    George, M. A.; Azoulay, M.; Jayatirtha, H. N.; Biao, Y.; Burger, A.; Collins, W. E.; Silberman, E.

    1994-03-01

    Atomic force microscopy (AFM) was used to characterize the surface of lead iodide crystals. The high vapor pressure of lead iodide prohibits the use of traditional high resolution surface study techniques that require high vacuum conditions. AFM was used to image numerous insulating surface in various ambients, with very little sample preparation techniques needed. Freshly cleaved and modified surfaces, including, chemical and vacuum etched, and air aged surfaces, were examined. Both intrinsic and induced defects were imaged with high resolution. The results were compared to a similar AFM study of mercuric iodide surfaces and it was found that, at ambient conditions, lead iodide is significantly more stable than mercuric iodide.

  11. Formulation and optimization of potassium iodide tablets

    OpenAIRE

    Al-Achi, Antoine; Patel, Binit

    2014-01-01

    The use of potassium iodide (KI) as a protective agent against accidental radioactive exposure is well established. In this study, we aimed to prepare a KI tablet formulation using a direct compression method. We utilized Design of Experiment (DoE)/mixture design to define the best formulation with predetermined physical qualities as to its dissolution, hardness, assay, disintegration, and angle of repose. Based on the results from the DoE, the formulation had the following components (%w/w):...

  12. Formulation and optimization of potassium iodide tablets.

    Science.gov (United States)

    Al-Achi, Antoine; Patel, Binit

    2015-01-01

    The use of potassium iodide (KI) as a protective agent against accidental radioactive exposure is well established. In this study, we aimed to prepare a KI tablet formulation using a direct compression method. We utilized Design of Experiment (DoE)/mixture design to define the best formulation with predetermined physical qualities as to its dissolution, hardness, assay, disintegration, and angle of repose. Based on the results from the DoE, the formulation had the following components (%w/w): Avicel 48.70%, silicon dioxide 0.27%, stearic acid (1.00%), magnesium stearate 2.45%, and dicalcium phosphate 18.69%, in addition to potassium iodide 28.89% (130 mg/tablet). This formulation was scaled-up using two tablet presses, a single-punch press and a rotary mini tablet press. The final scaled-up formulation was subjected to a variety of quality control tests, including photo-stability testing. The results indicate that potassium iodide tablets prepared by a rotary mini tablet press had good pharmaceutical characteristics and a shelf-life of 25 days when stored at room temperature protected from light.

  13. Formation of cyanogen iodide by lactoperoxidase.

    Science.gov (United States)

    Schlorke, Denise; Flemmig, Jörg; Birkemeyer, Claudia; Arnhold, Jürgen

    2016-01-01

    The haem protein lactoperoxidase (LPO) is an important component of the anti-microbial immune defence in external secretions and is also applied as preservative in food, oral care and cosmetic products. Upon oxidation of SCN(-) and I(-) by the LPO-hydrogen peroxide system, oxidised species are formed with bacteriostatic and/or bactericidal activity. Here we describe the formation of the inter(pseudo)halogen cyanogen iodide (ICN) by LPO. This product is formed when both, thiocyanate and iodide, are present together in the reaction mixture. Using (13)C nuclear magnetic resonance spectroscopy and gas chromatography-mass spectrometry we could identify this inter(pseudo)halogen after applying iodide in slight excess over thiocyanate. The formation of ICN is based on the reaction of oxidised iodine species with thiocyanate. Further, we could demonstrate that ICN is also formed by the related haem enzyme myeloperoxidase and, in lower amounts, in the enzyme-free system. As I(-) is not competitive for SCN(-) under physiologically relevant conditions, the formation of ICN is not expected in secretions but may be relevant for LPO-containing products.

  14. Cu-catalyzed trifluoromethylation of aryl iodides with trifluoromethylzinc reagent prepared in situ from trifluoromethyl iodide

    Directory of Open Access Journals (Sweden)

    Yuzo Nakamura

    2013-11-01

    Full Text Available The trifluoromethylation of aryl iodides catalyzed by copper(I salt with trifluoromethylzinc reagent prepared in situ from trifluoromethyl iodide and Zn dust was accomplished. The catalytic reactions proceeded under mild reaction conditions, providing the corresponding aromatic trifluoromethylated products in moderate to high yields. The advantage of this method is that additives such as metal fluoride (MF, which are indispensable to activate silyl groups for transmetallation in the corresponding reactions catalyzed by copper salt by using the Ruppert–Prakash reagents (CF3SiR3, are not required.

  15. Vapor Growth of Mercuric Iodide Tetragonal Prismatic Crystals

    Science.gov (United States)

    2013-03-01

    These steps were followed by immersion in 1% potassium iodide (KI) solution. The apparatus were then cleaned and rinsed thoroughly with deionized (DI...Pergamon Press, 1973. [34] N. Lyakh, “Composition and kinetic characteristics of vapour phase during mercuric iodide growing,” Crystal Res. Technol...DTRA-TR-13-6 Vapor Growth of Mercuric Iodide Tetragonal Prismatic Crystals Approved for public release, distribution is unlimited. March 2013

  16. Effect of nitrogen and oxygen on radiolysis of iodide solution

    Energy Technology Data Exchange (ETDEWEB)

    Karasawa, H.; Endo, M. [Hitachi Ltd., Power and Industrial System R+D Divisions, Ibaraki (Japan)

    1996-12-01

    The effect of nitrogen and oxygen on radiolysis of iodide solution was examined. Direct decomposition of nitrogen by {gamma}-radiation produced nitric acid to decrease a water pH. This resulted in the iodine formation in the radiolysis of iodide solution. Hydrogen peroxide was produced by the radiolysis of water containing oxygen. This worked a reducing agent to suppress the formation of iodine in the radiolysis of iodide solution. In the analytical model, fourteen iodine species were considered and reaction scheme consisted in 124 reactions. The analytical model could estimate the oxidation state of iodide ions. (author) 4 figs., 4 refs.

  17. Mercuric Iodide Anticoincidence Shield for Gamma-Ray Spectrometer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to utilize a new detector material, polycrystalline mercuric iodide, for background suppression by active anticoincidence shielding in gamma-ray...

  18. Mercuric Iodide Anticoincidence Shield for Gamma-Ray Spectrometer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We utilize a new detector material, polycrystalline mercuric iodide, for background suppression by active anticoincidence shielding in gamma-ray spectrometers. Two...

  19. The addition of iodine to tetramethylammonium iodide

    Science.gov (United States)

    Foote, H.W.; Fleischer, M.

    1953-01-01

    The system tetramethylammonium iodide-iodine-toluene has been studied by the solubility method at 6 and at 25??. The compounds (CH3)4NI3, (CH3)4NI5 and (CH3)4NI11 were found to be stable phases at both temperatures. In addition, the compound (CH3)4NI10 was found at 6?? and the compound (CH3)4NI9 at 25??. The dissociation pressures of the compounds at these temperatures were calculated from the solubility data.

  20. Electronic and optical properties of lead iodide

    DEFF Research Database (Denmark)

    Ahuja, R.; Arwin, H.; Ferreira da Silva, A.

    2002-01-01

    The electronic properties and the optical absorption of lead iodide (PbI2) have been investigated experimentally by means of optical absorption and spectroscopic ellipsometry, and theoretically by a full-potential linear muffin-tin-orbital method. PbI2 has been recognized as a very promising...... detector material with a large technological applicability. Its band-gap energy as a function of temperature has also been measured by optical absorption. The temperature dependence has been fitted by two different relations, and a discussion of these fittings is given. ©2002 American Institute of Physics....

  1. Novel mercuric iodide polycrystalline nuclear particles counters

    Energy Technology Data Exchange (ETDEWEB)

    Schieber, M. [Hebrew Univ. of Jerusalem (Israel)]|[Sandia National Lab., Livermore, CA (United States); Zuck, A.; Braiman, M.; Nissenbaum, J. [Hebrew Univ. of Jerusalem (Israel)] [and others

    1996-12-31

    Polycrystalline mercuric iodide nuclear radiation detectors having areas between 0.01 to 100 cm{sup 2} and thicknesses 30 to 600 microns, have been fabricated with single, linear strip and square pixel contact. The large area detectors 10 to 600 cm{sup 2} were produced by industrial ceramic equipment while the smaller ones, about 1 cm{sup 2} area, were produced in the laboratory. The large detectors still had large leakage currents and the production process is being revised. The smaller detectors were tested and their response to lower and higher gamma energy, beta and even 100 GeV muons at CERN will be reported.

  2. Production of Molecular Iodine and Tri-iodide in the Frozen Solution of Iodide: Implication for Polar Atmosphere.

    Science.gov (United States)

    Kim, Kitae; Yabushita, Akihiro; Okumura, Masanori; Saiz-Lopez, Alfonso; Cuevas, Carlos A; Blaszczak-Boxe, Christopher S; Min, Dae Wi; Yoon, Ho-Il; Choi, Wonyong

    2016-02-01

    The chemistry of reactive halogens in the polar atmosphere plays important roles in ozone and mercury depletion events, oxidizing capacity, and dimethylsulfide oxidation to form cloud-condensation nuclei. Among halogen species, the sources and emission mechanisms of inorganic iodine compounds in the polar boundary layer remain unknown. Here, we demonstrate that the production of tri-iodide (I3(-)) via iodide oxidation, which is negligible in aqueous solution, is significantly accelerated in frozen solution, both in the presence and the absence of solar irradiation. Field experiments carried out in the Antarctic region (King George Island, 62°13'S, 58°47'W) also showed that the generation of tri-iodide via solar photo-oxidation was enhanced when iodide was added to various ice media. The emission of gaseous I2 from the irradiated frozen solution of iodide to the gas phase was detected by using cavity ring-down spectroscopy, which was observed both in the frozen state at 253 K and after thawing the ice at 298 K. The accelerated (photo-)oxidation of iodide and the subsequent formation of tri-iodide and I2 in ice appear to be related with the freeze concentration of iodide and dissolved O2 trapped in the ice crystal grain boundaries. We propose that an accelerated abiotic transformation of iodide to gaseous I2 in ice media provides a previously unrecognized formation pathway of active iodine species in the polar atmosphere.

  3. Phase 2 Methyl Iodide Deep-Bed Adsorption Tests

    Energy Technology Data Exchange (ETDEWEB)

    Soelberg, Nick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Watson, Tony [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-09-01

    Nuclear fission produces fission products (FPs) and activation products, including iodine-129, which could evolve into used fuel reprocessing facility off-gas systems, and could require off-gas control to limit air emissions to levels within acceptable emission limits. Research, demonstrations, and some reprocessing plant experience have indicated that diatomic iodine can be captured with efficiencies high enough to meet regulatory requirements. Research on the capture of organic iodides has also been performed, but to a lesser extent. Several questions remain open regarding the capture of iodine bound in organic compounds. Deep-bed methyl iodide adsorption testing has progressed according to a multi-laboratory methyl iodide adsorption test plan. This report summarizes the second phase of methyl iodide adsorption work performed according to this test plan using the deep-bed iodine adsorption test system at the Idaho National Laboratory (INL), performed during the second half of Fiscal Year (FY) 2014. Test results continue to show that methyl iodide adsorption using AgZ can achieve total iodine decontamination factors (DFs, ratios of uncontrolled and controlled total iodine levels) above 1,000, until breakthrough occurred. However, mass transfer zone depths are deeper for methyl iodide adsorption compared to diatomic iodine (I2) adsorption. Methyl iodide DFs for the Ag Aerogel test adsorption efficiencies were less than 1,000, and the methyl iodide mass transfer zone depth exceeded 8 inches. Additional deep-bed testing and analyses are recommended to (a) expand the data base for methyl iodide adsorption under various conditions specified in the methyl iodide test plan, and (b) provide more data for evaluating organic iodide reactions and reaction byproducts for different potential adsorption conditions.

  4. Kinetic Isotope Effects in the Reduction of Methyl Iodide

    DEFF Research Database (Denmark)

    Holm, Torkil

    1999-01-01

    a-Deuterium kinetic isotope effects (KIE's) have been determined for the reaction of methyl iodide with a series of reducing agents. Reagents which transfer hydride ion in an SN2 reaction show small inverse or small normal KIE's. Reagents which transfer an electron to methyl iodide to produce...

  5. Silver iodide sodalite for 129I immobilisation

    Science.gov (United States)

    Vance, E. R.; Gregg, D. J.; Grant, C.; Stopic, A.; Maddrell, E. R.

    2016-11-01

    Silver iodide sodalite was initially synthesised as a fine-grained major phase in a nominally stoichiometric composition following hot isostatic pressing at 850 °C with 100 MPa and its composition, Ag4Al3Si3O12I, was approximately verified by scanning electron microscopy. An alternative preparative method yielded a more dense and stoichiometric AgI sodalite on sintering and HIPing. As found for AgI, the I is released from AgI sodalite much more readily in reducing water than in ordinary water. Thus in normal PCT-B tests, the I release was <0.3 g/L in water, but it was ∼70 g/L under highly reducing conditions. This is an important point with regard to can material if HIPing is used for consolidation.

  6. Novel mercuric iodide polycrystalline nuclear particle counters

    Energy Technology Data Exchange (ETDEWEB)

    Schieber, M. [Hebrew Univ. of Jerusalem (Israel)]|[Sandia National Labs., Livermore, CA (United States); Zuck, A.; Braiman, M.; Nissenbaum, J. [Hebrew Univ. of Jerusalem (Israel); Turchetta, R.; Dulinski, W.; Husson, D.; Riester, J.L. [LEPSI, Strasbourg (France)

    1997-12-01

    Polycrystalline mercuric iodide nuclear radiation detectors have been produced in a novel technology. Unlike the normal single-crystal technology, there is no intrinsic limit to the surface on which these detectors can be produced. Detectors with areas up to about 1.5 cm{sup 2}, thicknesses from 30 to 600 {micro}m, and with single electrodes as well as microstrip and pixel contacts have been fabricated and successfully tested with photons in the range of 40--660 keV, {beta} particle`s emitted from a Sr-Y source, and high energy (100 GeV) muons. Results on both charge collection and counting efficiency are reported as well as some very preliminary imaging results. The experimental results on charge collection have been compared with simulation, and a combined {mu}{tau} product 10{sup {minus}7} cm{sup 2}/V for electrons has been estimated.

  7. Ferroelastic Fingerprints in Methylammonium Lead Iodide Perovskite

    KAUST Repository

    Hermes, Ilka M.

    2016-02-12

    Methylammonium lead iodide (MAPbI3) perovskite materials show an outstanding performance in photovoltaic devices. However, certain material properties, especially the possible ferroic behavior, remain unclear. We observed distinct nanoscale periodic domains in the piezoresponse of MAPbI3(Cl) grains. The structure and the orientation of these striped domains indicate ferroelasticity as their origin. By correlating vertical and lateral piezoresponse force microscopy experiments performed at different sample orientations with x-ray diffraction, the preferred domain orientation was suggested to be the a1-a2-phase. The observation of these ferroelastic fingerprints appears to strongly depend on the film texture and thus the preparation route. The formation of the ferroelastic twin domains could be induced by internal strain during the cubic-tetragonal phase transition.

  8. Conserved charged amino acid residues in the extracellular region of sodium/iodide symporter are critical for iodide transport activity

    Directory of Open Access Journals (Sweden)

    Liang Ji-An

    2010-11-01

    Full Text Available Abstract Background Sodium/iodide symporter (NIS mediates the active transport and accumulation of iodide from the blood into the thyroid gland. His-226 located in the extracellular region of NIS has been demonstrated to be critical for iodide transport in our previous study. The conserved charged amino acid residues in the extracellular region of NIS were therefore characterized in this study. Methods Fourteen charged residues (Arg-9, Glu-79, Arg-82, Lys-86, Asp-163, His-226, Arg-228, Asp-233, Asp-237, Arg-239, Arg-241, Asp-311, Asp-322, and Asp-331 were replaced by alanine. Iodide uptake abilities of mutants were evaluated by steady-state and kinetic analysis. The three-dimensional comparative protein structure of NIS was further modeled using sodium/glucose transporter as the reference protein. Results All the NIS mutants were expressed normally in the cells and targeted correctly to the plasma membrane. However, these mutants, except R9A, displayed severe defects on the iodide uptake. Further kinetic analysis revealed that mutations at conserved positively charged amino acid residues in the extracellular region of NIS led to decrease NIS-mediated iodide uptake activity by reducing the maximal rate of iodide transport, while mutations at conserved negatively charged residues led to decrease iodide transport by increasing dissociation between NIS mutants and iodide. Conclusions This is the first report characterizing thoroughly the functional significance of conserved charged amino acid residues in the extracellular region of NIS. Our data suggested that conserved charged amino acid residues, except Arg-9, in the extracellular region of NIS were critical for iodide transport.

  9. Barium iodide and strontium iodide crystals and scintillators implementing the same

    Energy Technology Data Exchange (ETDEWEB)

    Payne, Stephen A.; Cherepy, Nerine J.; Hull, Giulia E.; Drobshoff, Alexander D.; Burger, Arnold

    2016-11-29

    In one embodiment, a material comprises a crystal comprising strontium iodide providing at least 50,000 photons per MeV, where the strontium iodide material is characterized by a volume not less than 1 cm.sup.3. In another embodiment, a scintillator optic includes europium-doped strontium iodide providing at least 50,000 photons per MeV, where the europium in the crystal is primarily Eu.sup.2+, and the europium is present in an amount greater than about 1.6%. A scintillator radiation detector in yet another embodiment includes a scintillator optic comprising SrI.sub.2 and BaI.sub.2, where a ratio of SrI.sub.2 to BaI.sub.2 is in a range of between 0:1 and 1.0, the scintillator optic is a crystal that provides at least 50,000 scintillation photons per MeV and energy resolution of less than about 5% at 662 keV, and the crystal has a volume of 1 cm.sup.3 or more; the scintillator optic contains more than about 2% europium.

  10. Long-term effects of an intracavitary treatment with californium-252 on normal tissue. [Swine, /sup 226/Ra

    Energy Technology Data Exchange (ETDEWEB)

    Sullivan, M.F.; Beamer, J.L.; Mahony, T.D.; Cross, F.T.; Lund, J.E.; Endres, G.W.R.

    1976-01-01

    About one hundred fifty swine were exposed to either radium-226 or californium-252 sources in the uterine cervix to determine an RBE for both acute and long-term effects. That value for early changes in the tissues at risk in the treatment of cervical cancer was between 6.2 and 6.8. The incidence of complications increased with time after exposure, especially among animals treated with /sup 252/Cf. Analysis of rectal injury showed that ulceration occurred frequently within a year postexposure at doses between 1600 and 2400 rad calculated at 2 cm lateral to the source midline. Fat necrosis and smooth muscle atrophy, resulting in a local rectal stricture, were delayed changes observed in some animals. The lower ureter was the site for a greater frequency of complications than the GI tract. Ureteral stricture often occurred at doses of 1200 rad from /sup 252/Cf and 7000 rad from /sup 226/Ra. Observation of delayed effects in the uterine-cervix in animals held up to 4 years postexposure indicate that the RBE for /sup 252/Cf may be increased to a value as high as 18, while repair may have even decreased it to about 5.6 in the rectum. Fifty swine are still being observed for long-term effects after doses above 800 rad from /sup 252/Cf and 5000 rad from /sup 226/Ra.

  11. Development of electron beam ion source charge breeder for rare isotopes at Californium Rare Isotope Breeder Upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Kondrashev, S.; Dickerson, C.; Levand, A.; Ostroumov, P. N.; Pardo, R. C.; Savard, G.; Vondrasek, R. [Physics Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Alessi, J.; Beebe, E.; Pikin, A. [Collider-Accelerator Department, Brookhaven National Laboratory, Upton, New York 11973 (United States); Kuznetsov, G. I.; Batazova, M. A. [Budker Institute of Nuclear Physics, Novosibirsk 630090 (Russian Federation)

    2012-02-15

    Recently, the Californium Rare Isotope Breeder Upgrade (CARIBU) to the Argonne Tandem Linac Accelerator System (ATLAS) was commissioned and became available for production of rare isotopes. Currently, an electron cyclotron resonance ion source is used as a charge breeder for CARIBU beams. To further increase the intensity and improve the purity of neutron-rich ion beams accelerated by ATLAS, we are developing a high-efficiency charge breeder for CARIBU based on an electron beam ion source (EBIS). The CARIBU EBIS charge breeder will utilize the state-of-the-art EBIS technology recently developed at Brookhaven National Laboratory (BNL). The electron beam current density in the CARIBU EBIS trap will be significantly higher than that in existing operational charge-state breeders based on the EBIS concept. The design of the CARIBU EBIS charge breeder is nearly complete. Long-lead components of the EBIS such as a 6-T superconducting solenoid and an electron gun have been ordered with the delivery schedule in the fall of 2011. Measurements of expected breeding efficiency using the BNL Test EBIS have been performed using a Cs{sup +} surface ionization ion source for external injection in pulsed mode. In these experiments we have achieved {approx}70% injection/extraction efficiency and breeding efficiency into the most abundant charge state of {approx}17%.

  12. Development of electron beam ion source charge breeder for rare isotopes at Californium Rare Isotope Breeder Upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Kondrashev S.; Alessi J.; Dickerson, C.; Levand, A.; Ostroumov, P.N.; Pardo, R.C.; Savard, G.; Vondrasek, R.; Beebe, E.; Pikin, A.; Kuznetsov, G.I.; Batazova, M.A.

    2012-02-03

    Recently, the Californium Rare Isotope Breeder Upgrade (CARIBU) to the Argonne Tandem Linac Accelerator System (ATLAS) was commissioned and became available for production of rare isotopes. Currently, an electron cyclotron resonance ion source is used as a charge breeder for CARIBU beams. To further increase the intensity and improve the purity of neutron-rich ion beams accelerated by ATLAS, we are developing a high-efficiency charge breeder for CARIBU based on an electron beam ion source (EBIS). The CARIBU EBIS charge breeder will utilize the state-of-the-art EBIS technology recently developed at Brookhaven National Laboratory (BNL). The electron beam current density in the CARIBU EBIS trap will be significantly higher than that in existing operational charge-state breeders based on the EBIS concept. The design of the CARIBU EBIS charge breeder is nearly complete. Long-lead components of the EBIS such as a 6-T superconducting solenoid and an electron gun have been ordered with the delivery schedule in the fall of 2011. Measurements of expected breeding efficiency using the BNL Test EBIS have been performed using a Cs{sup +} surface ionization ion source for external injection in pulsed mode. In these experiments we have achieved {approx}70% injection/extraction efficiency and breeding efficiency into the most abundant charge state of {approx}17%.

  13. Expression of the human sodium/iodide symporter (hNIS) in xenotransplanted human thyroid carcinoma

    NARCIS (Netherlands)

    Smit, J.W.A.; Schröder - van der Elst, J.P.; Karperien, M.; Que, I.; Romijn, J.A.; Heide, van der D.

    2001-01-01

    The uptake of iodide in thyroid epithelial cells is mediated by the sodium/iodide symporter (NIS). The uptake of iodide is of vital importance for thyroid physiology and is a prerequisite for radioiodine therapy in thyroid cancer. Loss of iodide uptake due to diminished expression of the human NIS (

  14. Improved Stability of Mercuric Iodide Detectors for Anticoincidence Shields Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to utilize guard ring electrode structures and a new film growth technique to create improved polycrystalline mercuric iodide detectors for background...

  15. Prevention of organic iodide formation in BWR`s

    Energy Technology Data Exchange (ETDEWEB)

    Karjunen, T. [Finnish Centre for Radiation and Nuclear Safety, Helsinki (Finland); Laitinen, T.; Piippo, J.; Sirkiae, P. [VTT Manufacturing Technology (Finland)

    1996-12-01

    During an accident, many different forms of iodine may emerge. Organic iodides, such as methyl iodide and ethyl iodide, are relatively volatile, and thus their appearance leads to increased concentration of gaseous iodine. Since organic iodides are also relatively immune to most accident mitigation measures, such as sprays and filters, they can affect the accident source term significantly even when only a small portion of iodine is in organic form. Formation of organic iodides may not be limited by the amount of organic substances available. Excessive amounts of methane can be produced, for example, during oxidation of boron carbide, which is used in BWR`s as a neutron absorber material. Another important source is cable insulation. In a BWR, a large quantity of cables is placed below the pressure vessel. Thus a large quantity of pyrolyse gases will be produced, should the vessel fail. Organic iodides can be formed as a result of many different reactions, but at least in certain conditions the main reaction takes place between an organic radical produced by radiolysis and elemental iodine. A necessary requirement for prevention of organic iodide production is therefore that the pH in the containment water pools is kept high enough to eliminate formation of elemental iodine. In a typical BWR the suppression pool water is usually unbuffered. As a result, the pH may be dominated by chemicals introduced during an accident. If no system for adding basic chemicals is operable, the main factor affecting pool water pH may be hydrochloric acid released during cable degradation. Should this occur, the conditions could be very favorable for production of elemental iodine and, consequently, formation of organic iodides. Although high pH is necessary for iodine retention, it could have also adverse effects. High pH may, for example, accelerate corrosion of containment materials and alter the characteristics of the solid corrosion products. (author) 6 figs., 1 tab., 13 refs.

  16. Chloride, bromide and iodide scintillators with europium

    Science.gov (United States)

    Zhuravleva, Mariya; Yang, Kan

    2016-09-27

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  17. Electrochemical reaction rates in a dye-sensitised solar cell - the iodide/tri-iodide redox system

    DEFF Research Database (Denmark)

    Bay, L.; West, K.; Winther-Jensen, B.

    2006-01-01

    The electrochemical reaction rate of the redox couple iodide/tri-iodide in acetonitrile is characterised by impedance spectroscopy. Different electrode materials relevant for the function of dye-sensitised solar cells (DSSC) are investigated. Preferably, the reaction with the iodide....../tri-iodide couple should be fast at the counter electrode, i.e. this electrode must have a high catalytic activity towards the redox couple, and the same reaction must be slow on the photo electrode. The catalytic activity is investigated for platinum, poly(3,4-ethylenedioxythiophene) (PEDOT), polypyrrole (PPy......), and polyaniline (PANI)-all deposited onto fluorine-doped tin oxide (FTO) glass. Both Pt and PEDOT are found to have sufficiently high catalytic activities for practical use as counter electrodes in DSSC. The reaction resistance on FTO and anatase confirmed the beneficial effect of a compact anatase layer on top...

  18. Iodide kinetics and experimental I-131 therapy in a xenotransplanted human sodium-iodide symporter-transfected human follicular thyroid carcinoma cell line

    NARCIS (Netherlands)

    Smit, J.W.A.; Elst, van der J.P.; Karperien, M.; Que, I.; Stokkel, M.; Heide, van der D.; Romijn, J.A.

    2002-01-01

    Uptake of iodide is a prerequisite for radioiodide therapy in thyroid cancer. However, loss of iodide uptake is frequently observed in metastasized thyroid cancer, which may be explained by diminished expression of the human sodium-iodide symporter (hNIS). We studied whether transfection of hNIS int

  19. Molecular imaging using sodium iodide symporter (NIS)

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Je Yoel [School of Dentistry, Kyungpook National Univ., Daegu (Korea, Republic of)

    2004-04-01

    Radioiodide uptake in thyroid follicular epithelial cells, mediated by a plasma membrane transporter, sodium iodide symporter (NIS), provides a first step mechanism for thyroid cancer detection by radioiodide injection and effective radioiodide treatment for patients with invasive, recurrent, and/or metastatic thyroid cancers after total thyroidectomy. NIS gene transfer to tumor cells may significantly and specifically enhance internal radioactive accumulation of tumors following radioiodide administration, and result in better tumor control. NIS gene transfers have been successfully performed in a variety of tumor animal models by either plasmid-mediated transfection or virus (adenovirus or retrovirus)-mediated gene delivery. These animal models include nude mice xenografted with human melanoma, glioma, breast cancer of prostate cancer, rats with subcutaneous thyroid tumor implantation, as well as the rat intracranial glioma model. In these animal models, non-invasive imaging of in vivo tumors by gamma camera scintigraphy after radioiodide or technetium injection has been performed successfully, suggesting that the NIS can serve as an imaging reporter gene for gene therapy trials. In addition, the tumor killing effects of I-131, ReO4-188 and At-211 after NIS gene transfer have been demonstrated in in vitro clonogenic assays and in vivo radioiodide therapy studies, suggesting that NIS gene can also serve as a therapeutic requires a more efficient and specific system of gene delivery with better retention of radioiodide in tumor. Results thus far are, however, promising, and suggest that NIS gene transfer followed by radioiodide treatment will allow non-invasive in vivo imaging to assess the outcome of gene therapy and provide a therapeutic strategy for a variety of human diseases.

  20. Evaluation of mercuric iodide ceramic semiconductor detectors

    Energy Technology Data Exchange (ETDEWEB)

    Schieber, M.; Zuck, A.; Braiman, M.; Nissenbaum, J. [Hebrew Univ., Jerusalem (Israel); Turchetta, R.; Dulinski, W.; Husson, D.; Riester, J.L. [LEPSI (ULP/IN2P3), Strasbourg (France)

    1998-02-01

    Mercuric iodide ceramic radiation detectors, which can act as nuclear particle counters, have been fabricated with single continuos electrical contacts and with linear strip contacts. They have been tested with different kinds of {gamma} and {beta} sources as well as in a high energy beam at CERN. The detectors were also successfully tested for radiation hardness with irradiation of 5*10{sup 14} neutrons/cm{sup 2}. The ratio of detected photons over the number of absorbed photons has been measured with {gamma} sources of different energies, and it ranges from 20% at 44 keV up to about 30% at 660 keV. An absolute efficiency of 70% has been measured for a 350 {mu}m thick detector for {beta} particles emitted by a {sup 90}Sr source. Charge collection efficiency, defined as the amount of charge induced on the electrodes by a mminimum ionizing particle (MIP) traversing the detector, has been measured in two samples. The average collected charge fits well with a linear curve with slope of 35 electrons/(kV/cm) per 100 {mu}m. This result is well described by a dynamic device simulation, where the free carrier mean lifetime is used as a free parameter, adjusted to a value of 1.5 ns, i.e. about 1/100 of the corresponding lifetime in single crystal HgI{sub 2} detectors. The response to MIP has also been studied with a high energy (100 GeV) muon beam in CERN. A preliminary beam profile is presented while a more detailed analysis is still in progress and will be presented elsewhere. These results together with the low cost of the material make ceramic HgI{sub 2} detectors excellent candidates for large area particle tracking and imaging applications, even in a radiation harsh environment. (orig.). 14 refs.

  1. Macrosegregation during Plane Front Solidification of Cesium Iodide wt Percent Thallium Iodide Alloy

    Science.gov (United States)

    Sidawi, Ibrahim M. S.

    Macrosegregation produced during directional solidification of CsI-1 wt% TlI by vertical Bridgman technique has been examined in crucibles of varying diameter, from 0.5 to 2.0 cm. Phase diagram and temperature dependence of the thermal conductivity have been determined. The experimentally observed liquid-solid interface shape and the fluid flow behavior have been compared with that computed from the commercially available code FIDAP. Thallium iodide content of the alloy was observed to increase along the length of the directionally solidified specimens, resulting in continuously decreasing light output. The experimentally observed solutal distribution agrees with predictions from the boundary layer model of Favier. The observed macrosegregation behavior suggests that there is a significant convection in the melt even in the smallest crucible diameter of 0.5 cm.

  2. Bismuth tri-iodide radiation detector development

    Science.gov (United States)

    Gokhale, Sasmit S.

    Bismuth tri-iodide is an attractive material for room temperature radiation detection. BiI3 demonstrates a number of properties that are apt for semiconductor radiation detection, especially gamma ray spectroscopy. The high atomic number (ZBi = 83 and ZI = 53) and the relatively high density (5.78 g/cm3) cause the material to have good photon stopping power, while the large band-gap (1.67 eV ) allows it to function as a room temperature radiation detector without any cooling mechanism. This work presents the fabrication and characterization of BiI3 radiation detectors. For the purpose of this research detectors were fabricated by cutting BiI3 crystal boules, followed by mechanical and chemical surface treatments. Detectors with various electrode geometries enabling single polarity charge sensing were fabricated. The electrical characteristics and the radiation response of the detectors were measured. The radiation response measurement was performed at room temperature using a 241Am alpha particle source and a 241Am sealed gamma-ray source. The spectral resolutions of the detectors varied from 2.09% - 6.1% for 59.5 keV gamma-rays and between 26% - 40% for 5.48 MeV alpha particles. Charge carrier properties such as the electron and hole mobility and lifetime were also estimated. The electron mobility for an ultrapure BiI 3 detector was estimated to be approximately 433 cm 2/Vs while that for antimony doped BiI3 was estimated to be around 956 cm2/Vs and the mobility-lifetime product for electrons was estimated to be around 5.44 x 10-4 cm 2/V. Detector simulation was performed using the Monte Carlo simulation code MCNP5. A Matlab script which incorporates charge carrier trapping and statistical variation was written to generate a gamma-ray spectrum from the simulated energy deposition spectra. Measured and simulated spectra were compared to extract the charge carrier mobility-lifetime products, which for electrons and holes were estimated to be 5 x 10-3 cm2/V and 1.3 x

  3. Standard free energy of formation of iron iodide

    Science.gov (United States)

    Khandkar, A.; Tare, V. B.; Wagner, J. B., Jr.

    1983-01-01

    An experiment is reported where silver iodide is used to determine the standard free energy of formation of iron iodide. By using silver iodide as a solid electrolyte, a galvanic cell, Ag/AgI/Fe-FeI2, is formulated. The standard free energy of formation of AgI is known, and hence it is possible to estimate the standard free energy of formation of FeI2 by measuring the open-circuit emf of the above cell as a function of temperature. The free standard energy of formation of FeI2 determined by this method is -38784 + 24.165T cal/mol. It is estimated that the maximum error associated with this method is plus or minus 2500 cal/mol.

  4. Phase 1 Methyl Iodide Deep-Bed Adsorption Tests

    Energy Technology Data Exchange (ETDEWEB)

    Soelberg, Nick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Watson, Tony [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-08-22

    Nuclear fission results in the production of fission products (FPs) and activation products including iodine-129, which could evolve into used fuel reprocessing facility off-gas systems, and could require off-gas control to limit air emissions to levels within acceptable emission limits. Research, demonstrations, and some reprocessing plant experience have indicated that diatomic iodine can be captured with efficiencies high enough to meet regulatory requirements. Research on the capture of organic iodides has also been performed, but to a lesser extent [Jubin 2012b]. Several questions remain open regarding the capture of iodine bound in organic compounds. Deep-bed methyl iodide adsorption testing has progressed according to a multi-laboratory methyl iodide adsorption test plan. This report summarizes the first phase of methyl iodide adsorption work performed according to this test plan using the deep-bed iodine adsorption test system at the Idaho National Laboratory (INL), performed during Fiscal Year (FY) 2013 and early FY-2014. Testing has been performed to address questions posed in the test plan, and followed the testing outline in the test plan. Tests established detection limits, developed procedures for sample analysis with minimal analytical interferences, and confirmed earlier results that show that the methyl iodide reacts when in contact with the AgZ sorbent, and not significantly in the gas flow upstream of the sorbent. The reaction(s) enable separation of the iodine from the organic moiety, so that the iodine can chemisorb onto the sorbent. The organic moiety can form other compounds, some of which are organic compounds that are detected and can be tentatively identified using GC-FID and GCMS. Test results also show that other gas constituents (NOx and/or H2O) can affect the methyl iodide reactions. With NOx and H2O present in the gas stream, the majority of uncaptured iodine exiting iodine-laden sorbent beds is in the form of I2 or HI, species that

  5. Low energy background in mercuric iodide X-ray spectrometers

    Energy Technology Data Exchange (ETDEWEB)

    Bao, X.J. [TN Technol., Inc., Round Rock, TX (United States). Dept. of Anal. Instrum.; Natarajan, M. [TN Technol., Inc., Round Rock, TX (United States). Dept. of Anal. Instrum.; Henderson, J. [TN Technol., Inc., Round Rock, TX (United States). Dept. of Anal. Instrum.

    1996-10-01

    The origins of the continuous background (window effect or dead layer) in mercuric iodide X-ray spectrometers are investigated. It is found that photo-electron escape and carrier diffusion are the dominant mechanisms of incomplete charge collection in the energy range of interest (from 3-60 keV). X-ray spectra measurements, computer calculation and photo-response measurements are presented in support of the proposed model. Many observations of detector behavior made in the manufacturing and application of mercuric iodide X-ray detectors can be explained by this model. (orig.).

  6. Enhanced Olefin Cross Metathesis Reactions: The Copper Iodide Effect

    Science.gov (United States)

    Voigtritter, Karl; Ghorai, Subir

    2011-01-01

    Copper iodide has been shown to be an effective co-catalyst for the olefin cross metathesis reaction. In particular, it has both a catalyst stabilizing effect due to iodide ion, as well as copper(I)-based phosphine-scavenging properties that apply to use of the Grubbs-2 catalyst. A variety of Michael acceptors and olefinic partners can be cross-coupled under mild conditions in refluxing diethyl ether that avoid chlorinated solvents. This effect has also been applied to chemistry in water at room temperature using the new surfactant TPGS-750-M. PMID:21528868

  7. DBU-Promoted Trifluoromethylation of Aryl Iodides with Difluoromethyltriphenylphosphonium Bromide

    Institute of Scientific and Technical Information of China (English)

    Yun Wei; Liuying Yu; Jinhong Lin; Xing Zheng; Jichang Xiao

    2016-01-01

    DBU-promoted trifluoromethylation of aryl iodides with difluoromethyltriphenylphosphonium bromide (DFPB) in the presence of copper source is described.In this transformation,DBU not only acts as base to deprotonate the difluoromethyl group in DFPB to generate difluoromethylene phosphonium ylide Ph3P+CF2,but also converts the difluorocarbene generated from ylide Ph3P+CF2 into trifluoromethyl anion,finally resulting in the trifluoromethylation of aryl iodides.The reactions proceeded smoothly to afford expected products in moderate to good yields.

  8. Mercuric iodide dosimeter response to high energy electron beams

    Energy Technology Data Exchange (ETDEWEB)

    Loewinger, E.; Nissenbaum, J.; Schieber, M.M.

    1988-01-01

    Mercuric iodide solid state dosimeter response to high energy electron beams of up to 35 MeV is reported. High sensitivity of up to 1.5 V/cGy was observed with a 200 V external bias, as well as several mV/cGy, with no external bias for small volume (approx. 10 mm/sup 3/) detectors. The physical characteristics of the detector response are discussed, showing the feasibility of mercuric iodide as a reliable dosimeter for high energy electron beams.

  9. 40 CFR 415.510 - Applicability; description of the potassium iodide production subcategory.

    Science.gov (United States)

    2010-07-01

    ... potassium iodide production subcategory. 415.510 Section 415.510 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Potassium Iodide Production Subcategory § 415.510 Applicability; description of the potassium iodide production subcategory. The provisions of this subpart are applicable to...

  10. The electrosorption of tetraalkylammonium ions on silver iodide

    NARCIS (Netherlands)

    Keizer, de A.

    1981-01-01

    The object of the present investigations was to study the ef fect of the adsorption of charged organic ions on electrically charged, solid-liquid interfaces. To that end, symmetrical quater nary ammonium ions were adsorbed on a silver iodide-electrolyte interface at various surface charges. The elec

  11. Confinement Effects in Low-Dimensional Lead Iodide Perovskite Hybrids

    NARCIS (Netherlands)

    Kamminga, Machteld E.; Fang, Honghua; Filip, Marina R.; Giustino, Feliciano; Baas, Jacobus; Blake, Graeme R.; Loi, Maria Antonietta; Palstra, Thomas T. M.

    2016-01-01

    We use a layered solution crystal growth technique to synthesize high-quality single crystals of phenylalkylammonium lead iodide organic/inorganic hybrid compounds. Single-crystal X-ray diffraction reveals low-dimensional structures consisting of inorganic sheets separated by bilayers of the organic

  12. Radiation-hard polycrystalline mercuric iodide semiconductor particle counters

    Energy Technology Data Exchange (ETDEWEB)

    Schieber, M. [Hebrew Univ., Jerusalem (Israel)]|[Sandia National Laboratories, Livermore Ca 94556 (United States); Zuck, A.; Melekhov, L.; Nissenbaum, J. [Hebrew Univ., Jerusalem (Israel); Turchetta, R.; Dulinski, W.; Husson, D.; Riester, J.L. [LEPSI (ULP/IN2P3), Strasbourg (France)

    1998-06-01

    Mercuric iodide polycrystalline radiation detectors, which can act as nuclear particle counters and for large area imaging devices, have been fabricated using three different methods. Response to X- and gamma rays, beta particles and to 100GeV muons, as well as radiation hardness results are briefly described. (orig.) 8 refs.

  13. 21 CFR 520.763b - Dithiazanine iodide powder.

    Science.gov (United States)

    2010-04-01

    ....763b Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... is administered to dogs by mixing the proper dosage in the dog's food, using the following dosage... contraindicated in animals sensitive to dithiazanine iodide and should be used cautiously, if at all, in dogs...

  14. FY-2015 Methyl Iodide Deep-Bed Adsorption Test Report

    Energy Technology Data Exchange (ETDEWEB)

    Soelberg, Nicholas Ray [Idaho National Lab. (INL), Idaho Falls, ID (United States); Watson, Tony Leroy [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-09-30

    Nuclear fission produces fission and activation products, including iodine-129, which could evolve into used fuel reprocessing facility off-gas systems, and could require off-gas control to limit air emissions to levels within acceptable emission limits. Deep-bed methyl iodide adsorption testing has continued in Fiscal Year 2015 according to a multi-laboratory methyl iodide adsorption test plan. Updates to the deep-bed test system have also been performed to enable the inclusion of evaporated HNO3 and increased NO2 concentrations in future tests. This report summarizes the result of those activities. Test results showed that iodine adsorption from gaseous methyl iodide using reduced silver zeolite (AgZ) resulted in initial iodine decontamination factors (DFs, ratios of uncontrolled and controlled total iodine levels) under 1,000 for the conditions of the long-duration test performed this year (45 ppm CH3I, 1,000 ppm each NO and NO2, very low H2O levels [3 ppm] in balance air). The mass transfer zone depth exceeded the cumulative 5-inch depth of 4 bed segments, which is deeper than the 2-4 inch depth estimated for the mass transfer zone for adsorbing I2 using AgZ in prior deep-bed tests. The maximum iodine adsorption capacity for the AgZ under the conditions of this test was 6.2% (6.2 g adsorbed I per 100 g sorbent). The maximum Ag utilization was 51%. Additional deep-bed testing and analyses are recommended to (a) expand the data base for methyl iodide adsorption and (b) provide more data for evaluating organic iodide reactions and reaction byproducts for different potential adsorption conditions.

  15. Defective organification of iodide causing congenital goitrous hypothyroidism.

    Science.gov (United States)

    Ishikawa, N; Eguchi, K; Ohmori, T; Momotani, N; Nagayama, Y; Hosoya, T; Oguchi, H; Mimura, T; Kimura, S; Nagataki, S; Ito, K

    1996-01-01

    A 26-yr-old Japanese woman with congenital goitrous hypo-thyroidism and sensorineural deafness underwent a thyroidectomy. Examination of the thyroid gland revealed characteristic features of multinodular goiter. The T3 and T4 content in thyroglobulin (Tg) were 0.03 and 0.02 mol/mol Tg, respectively. Iodide incorporation into Tg, using slices of the thyroid tissue, revealed that iodide organification of thyroid tissue from our patient was markedly lower than that of normal controls. Then, guaiacol and iodide oxidation activities of thyroid peroxidase (TPO) in our patient's thyroid tissue were lower than those of normal controls (guaiacol assay: 1.92 vs. 30.0 +/- 5.7 mGU/mg protein; iodide assay: 1.1 vs. 6.6 +/- 2.8 mIU/mg protein). Lineweaver-Burk plot analysis of the oxidation rates of guaiacol and iodide indicated that this patient's TPO had a defect in the binding of guaiacol and iodide, but the coupling activity of the patient's TPO was not decreased compared with those of two normal thyroids. In this case and in control subjects, Nothern gel analysis of TPO messenger RNA from unstimulated and TSH-stimulated thyroid cells revealed a 3.2 kilobase species in the former and four distinct messenger RNA species of 4.0, 3.2, 2.1, and 1.7 kilobases in the latter. Western blot analysis of TPOs obtained from this patient and from control subjects identified the same 107 kDa protein, using antimicrosomal antibody-positive serum. We analyzed the coding sequence in the patient's TPO gene by using polymerase chain reaction technique. A single point mutation of G-->C at 1265 base pair was detected only in the TPO gene, but this point mutation does not alter the amino acid residue. It is possible that posttranslational modification such as abnormal glycosylation may occur in the TPO molecules. Furthermore, it is possible that there are differences in the tertiary structures of the TPO molecules between our patient and normal subjects. The above abnormalities of TPO molecules

  16. [Evaluation of potassium iodide in Polish dietary salt].

    Science.gov (United States)

    Andrzejewska, E; Rokicka, B; Gajda, J; Jarecka, J; Oraczewska, A; Karłowski, K

    1996-01-01

    The consequences of iodine deficiency occurring still in Poland include serious health disorders in the population, such as psycho- somatic retardation, hypothyroidism, endemic goitre, even cretinism. Administration of iodized edible salt with daily diet is an effective method for prevention of iodine deficiency. The condition of success is the proper level of potassium iodide in this salt and adequate distribution of iodized salt in various regions of the country. Successful iodine prophylaxis should be based on iodination of edible salt in amounts of 30 +/- 10 mg of KJ/kg. The permission given in the period from February to May 1994 by the General Sanitary Inspector for the production and marketing of edible salt iodized in proportions of 30 +/- 10 mg KJ/kg opened the possibility of starting its production in salt mines. The purpose of the presently reported work was to assess, in cooperation with the Province Sanitary Epidemiological Stations, the adequacy of iodination of the Polish edible salt produced in the years 1994-1995. The study was carried out according to the Polish Standard "Salt (Sodium Chloride) /PN-80/C-84081.35. Potassium iodide determination by photo colorimetric method." In 1995 the number of edible salt samples analyzed was 2484, and this number included 2129 samples of iodized salt. Potassium iodide content agreeing with the above permission was found in 122 samples, that is in 57.4% of iodized salt samples. In 603 samples (28.3%) of iodized salt this content was below that given in the permissions. In 1994 this study was carried out taking 2172 samples of edible salt, including 1586 samples of iodized salt. The content of potassium iodide agreeing with the permissions (30 +/- 10 mg/kg) was found in 342 samples (28, 1%), but 272 (22.4%) samples of iodized salt produced by salt mines contained lower amounts of potassium iodide than the amount indicated in the permissions, but still within the limits set down in the Polish Standard (20 +/- 5 mg

  17. Purification and deposition of silicon by an iodide disproportionation reaction

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Tihu (Littleton, CO); Ciszek, Theodore F. (Evergreen, CO)

    2002-01-01

    Method and apparatus for producing purified bulk silicon from highly impure metallurgical-grade silicon source material at atmospheric pressure. Method involves: (1) initially reacting iodine and metallurgical-grade silicon to create silicon tetraiodide and impurity iodide byproducts in a cold-wall reactor chamber; (2) isolating silicon tetraiodide from the impurity iodide byproducts and purifying it by distillation in a distillation chamber; and (3) transferring the purified silicon tetraiodide back to the cold-wall reactor chamber, reacting it with additional iodine and metallurgical-grade silicon to produce silicon diiodide and depositing the silicon diiodide onto a substrate within the cold-wall reactor chamber. The two chambers are at atmospheric pressure and the system is open to allow the introduction of additional source material and to remove and replace finished substrates.

  18. Synthesis and Structure of Bis(4-nitrobenzaldehyde thiosemicarbazone) Cadmium Iodide

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The title complex, bis(4-nitrobenzaldehyde thiosemicarbazone) cadmium iodide (C16H16CdI2N8O4S2) crystallizes in the triclinic system, space group P1 with a=9.632(2), b=11.227(2), c=14.031(3), α= 67.50(3), β= 86.99(3), γ= 66.64(3)°, V=1278.13, Z = 2, Dc = 2.117gcm-3, F(000) = 772, μ =3.472mm-1 MoKα radiation (λ=0.71073), R = 0.0443, wR= 0.1425 for 4529 observed reflections [I>2σ(I)] of 4731 independent reflections. The result shows that the structure contains CdL2I2 (where L = 4-nitrobenzaldehyde thiosemicarbazone) distorted tetrahedral units in which the two ligands are S-bonded as monodentate to cadmium ion; the two iodide ions are also coordinated to Cd(II).

  19. Caloric Effects in Methylammonium Lead Iodide from Molecular Dynamics Simulations

    OpenAIRE

    Liu, Shi; Cohen, Ronald E.

    2016-01-01

    Organic-inorganic hybrid perovskite architecture could serve as a robust platform for materials design to realize functionalities beyond photovoltaic applications. We explore caloric effects in organometal halide perovskites, taking methylammonium lead iodide (MAPbI$_3$) as an example, using all-atom molecular dynamics simulations with a first-principles based interatomic potential. The adiabatic thermal change is estimated directly by introducing different driving fields in the simulations. ...

  20. Structural insight into iodide uptake by AFm phases.

    Science.gov (United States)

    Aimoz, Laure; Wieland, Erich; Taviot-Guého, Christine; Dähn, Rainer; Vespa, Marika; Churakov, Sergey V

    2012-04-03

    The ability of cement phases carrying positively charged surfaces to retard the mobility of (129)I, present as iodide (I(-)) in groundwater, was investigated in the context of safe disposal of radioactive waste. (125)I sorption experiments on ettringite, hydrotalcite, chloride-, carbonate- and sulfate-containing AFm phases indicated that calcium-monosulfate (AFm-SO(4)) is the only phase that takes up trace levels of iodide. The structures of AFm phases prepared by coprecipitating iodide with other anions were investigated in order to understand this preferential uptake mechanism. X-ray diffraction (XRD) investigations showed a segregation of monoiodide (AFm-I(2)) and Friedel's salt (AFm-Cl(2)) for I-Cl mixtures, whereas interstratifications of AFm-I(2) and hemicarboaluminate (AFm-OH-(CO(3))(0.5)) were observed for the I-CO(3) systems. In contrast, XRD measurements indicated the formation of a solid solution between AFm-I(2) and AFm-SO(4) for the I-SO(4) mixtures. Extended X-ray absorption fine structure spectroscopy showed a modification of the coordination environment of iodine in I-CO(3) and in I-SO(4) samples compared to pure AFm-I(2). This is assumed to be due to the introduction of stacking faults in I-CO(3) samples on one hand and due to the presence of sulfate and associated space-filling water molecules as close neighbors in I-SO(4) samples on the other hand. The formation of a solid solution between AFm-I(2) and AFm-SO(4), with a short-range mixing of iodide and sulfate, implies that AFm-SO(4) bears the potential to retard (129)I.

  1. Development of the strontium iodide coded aperture (SICA) instrument

    Science.gov (United States)

    Mitchell, Lee J.; Phlips, Bernard F.; Grove, J. Eric; Cordes, Ryan

    2015-08-01

    The work reports on the development of a Strontium Iodide Coded Aperture (SICA) instrument for use in space-based astrophysics, solar physics, and high-energy atmospheric physics. The Naval Research Laboratory is developing a prototype coded aperture imager that will consist of an 8 x 8 array of SrI2:Eu detectors, each read out by a silicon photomultiplier. The array would be used to demonstrate SrI2:Eu detector performance for space-based missions. Europium-doped strontium iodide (SrI2:Eu) detectors have recently become available, and the material is a strong candidate to replace existing detector technology currently used for space-based gamma-ray astrophysics research. The detectors have a typical energy resolution of 3.2% at 662 keV, a significant improvement over the 6.5% energy resolution of thallium-doped sodium iodide. With a density of 4.59 g/cm and a Zeff of 49, SrI2:Eu has a high efficiency for MeV gamma-ray detection. Coupling this with recent improvements in silicon photomultiplier technology (i.e., no bulky photomultiplier tubes) creates high-density, large-area, low-power detector arrays with good energy resolution. Also, the energy resolution of SrI2:Eu makes it ideal for use as the back plane of a Compton telescope.

  2. Gold nanoelectrode ensembles for direct trace electroanalysis of iodide.

    Science.gov (United States)

    Pereira, Francisco C; Moretto, Ligia M; De Leo, Manuela; Zanoni, Maria V Boldrin; Ugo, Paolo

    2006-08-01

    A procedure for the standardization of ensembles of gold nanodisk electrodes (NEE) of 30 nm diameter is presented, which is based on the analytical comparison between experimental cyclic voltammograms (CV) obtained at the NEEs in diluted solutions of redox probes and CV patterns obtained by digital simulation. Possible origins of defects sometimes found in NEEs are discussed. Selected NEEs are then employed for the study of the electrochemical oxidation of iodide in acidic solutions. CV patterns display typical quasi-reversible behavior which involves associated chemical reactions between adsorbed and solution species. The main CV characteristics at the NEE compare with those observed at millimeter sized gold disk electrodes (Au-macro), apart a slight shift in E1/2 values and slightly higher peak to peak separation at the NEE. The detection limit (DL) at NEEs is 0.3 microM, which is more than one order of magnitude lower than DL at the Au-macro (4 microM). The mechanism of the electrochemical oxidation of iodide at NEEs is discussed. Finally, NEEs are applied to the direct determination of iodide at micromolar concentration levels in real samples, namely in some ophthalmic drugs and iodized table salt.

  3. Enhanced iodide sequestration by 3-biphenyl-5,6-dihydroimidazo 2,1-b thiazole in sodium/iodide sym-porter (NIS)-expressing cells

    Energy Technology Data Exchange (ETDEWEB)

    Lecat-Guillet, N.; Ambroise, Y. [CEA, DSV, Dept Bioorgan Chem andt IsotopLabelling, Inst Biol and Technol, iBiTecS, F-91191 Gif Sur Yvette (France)

    2008-07-01

    The ability of the sodium/iodide sym-porter (NIS) to take up iodide has long provided the basis for cyto-reductive gene therapy and cancer treatment with radio-iodide. One of the major limitations of this approach is that radio-iodide retention in NIS-expressing cells is not sufficient for their destruction. We identified and characterized a small organic molecule capable of increasing iodide retention in HEK293 cells permanently transfected with human NIS cDNA (hNIS-HEK293) and in the rat thyroid-derived cell line FRTL-5. In the presence of 3-biphenyl-4'-yl-5,6-dihydroimidazo[2,1-b)thiazole (ISA1), the transmembrane iodide concentration gradient was increased up to 4.5-fold. Our experiments indicate that the imidazo-thiazole derivative acts either by inhibiting anion efflux mechanisms, or by promoting the relocation of iodide into subcellular compartments. This new compound is not only an attractive chemical tool to investigate the mechanisms of iodide flux at the cellular level, but also opens promising perspectives in the treatment of cancer after NIS gene transfer. (authors)

  4. Removal and sequestration of iodide using silver-impregnated activated carbon.

    Science.gov (United States)

    Hoskins, Jay S; Karanfil, Tanju; Serkiz, Steven M

    2002-02-15

    Two silver-impregnated activated carbons (SIACs) (0.05 and 1.05 wt % silver) and their virgin (i.e., unimpregnated) granular activated carbon (GAC) precursors were investigated for their ability to remove and sequester iodide from aqueous solutions in a series of batch sorption and leaching experiments. Silver content, total iodide concentration, and pH were the factors controlling the removal mechanisms of iodide. Iodide uptake increased with decreasing pH for both SIACs and their virgin GACs. The 0.05% SIAC behaved similarly to its virgin GAC in all experimental conditions because of its low silver content. At pH values of 7 and 8 there was a marked increased in iodide removal for the 1.05% SIAC over that of its virgin GAC, while their performances were similar at a pH of 5. Scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) analyses prior to reaction with iodide showed the presence of metallic silver agglomerates on the 1.05% SIAC surface. After the reaction, elemental mapping with EDX showed the formation of silver iodide agglomerates. Oxidation of metallic silver was observed in the presence of oxygen, and the carbon surface appears to catalyze this reaction. When the molar ratio of silver to iodide was greater than 1 (i.e., M(Ag,SIAC) > M(I,TOTAL)), precipitation of silver iodide was the dominant removal mechanism. However, unreacted silver leached into solution with decreasing pH while iodide leaching did not occur. When M(Ag,SIAC) silver iodide precipitation occurred until all available silver had reacted, and additional iodide was removed from solution by pH-dependent adsorption to the GAC. Under this condition, silver leaching did not occur while iodide leaching increased with increasing pH.

  5. Electrochemistry of silver iodide the capacity of the double layer at the silver iodide-water interface

    NARCIS (Netherlands)

    Lyklema, J.; Overbeek, J.Th.G.

    1961-01-01

    A method is described for obtaining differential double layer capacities on silver iodide. Especially the influence of the nature and concentration of indifferent electrolytes was investigated, viz., the nitrates of Li·, K·, Rb·, NH4·, H·, Tl·, Mg··, Ba··, Co··, Cd··, Pb··, La···, Th····, the fluori

  6. Iron- Catalyzed 1,2-Addition of Perfluoroalkyl Iodides to Alkynes and Alkenes

    OpenAIRE

    Xu, Tao; Cheung, Chi Wai; Hu, Xile

    2014-01-01

    Iron catalysis has been developed for the intermolecular 1,2-addition of perfluoroalkyl iodides to alkynes and alkenes. The catalysis has a wide substrate scope and high functional-group tolerance. A variety of perfluoroalkyl iodides including CF3I can be employed. The resulting perfluoroalkylated alkyl and alkenyl iodides can be further functionalized by cross-coupling reactions. This methodology provides a straightforward and streamlined access to perfluoroalkylated organic molecules.

  7. Expression of sodium-iodide symporter in thyroid gland tumors: immunohistochemical study

    Directory of Open Access Journals (Sweden)

    Bondarenko O.O.

    2009-01-01

    Full Text Available One of the key moments of radioiodine therapy, and also radioisotope diagnostics of cancers of a thyroid gland is ability of their cells to accumulate iodide. This ability is provided with activity of the specific transporter – sodium-iodide symporter. Our research has shown disorders of sodium-iodide symporter immunoexpression in all tumors of thyroid gland: from overexpression and absence of plasma membrane expression in differentiated carcinomas, up to weak or actually absent in low differentiated cancers and Hurtle-cells tumors. Thus, there is a prospect of application of the sodium-iodide symporter, as the prognostic marker of thyroid cancers.

  8. Optical properties and surface morphology studies of palladium contacts on mercuric iodide single crystals

    Energy Technology Data Exchange (ETDEWEB)

    George, M.A.; Azoulay, M.; Burger, A.; Biao, Y.; Silberman, E. [Fisk Univ., Nashville, TN (United States). Dept. of Physics; Nason, D. [EG and G Energy Measurements, Inc., Goleta, CA (United States). Santa Barbara Operations

    1993-05-01

    Palladium is chemically suitable for electric contacts on mercuric iodide detectors for photon and nuclear radiation detection, so the understanding of palladium contacts is important for fundamental and practical scientific purposes. A study has been conducted on the surface morphology of evaporated contacts using Atomic Force Microscopy (AFM) and optical transmission and reflection. Evaporated palladium coatings are typically nonuniform and may deposit selectively on mercuric iodide surface defects. Reflection measurements show that coating thickness and surface treatment affect intensity, position and shape of a reflected peak characteristic of the mercuric iodide structure. Results indicate that the band gap energy in the surface of the mercuric iodide is lowered by palladium contacts.

  9. Optical properties and surface morphology studies of palladium contacts on mercuric iodide single crystals

    Science.gov (United States)

    George, M. A.; Azoulay, M.; Burger, A.; Biao, Y.; Silberman, E.; Nason, D.

    1993-04-01

    Palladium is chemically suitable for electric contacts on mercuric iodide detectors for photon and nuclear radiation detection, so the understanding of palladium contacts is important for fundamental and practical scientific purposes. A study has been conducted on the surface morphology of evaporated contacts using atomic force microscopy (AFM) and optical transmission and reflection. Evaporated palladium coatings are typically nonuniform and may deposit selectively on mercuric iodide surface defects. Reflection measurements show that coating thickness and surface treatment affect intensity, position, and shape of a reflected peak characteristic of the mercuric iodide structure. Results indicate that the band gap energy in the surface of the mercuric iodide is lowered by palladium contacts.

  10. Strontium iodide gamma ray spectrometers for planetary science (Conference Presentation)

    Science.gov (United States)

    Prettyman, Thomas H.; Rowe, Emmanuel; Butler, Jarrhett; Groza, Michael; Burger, Arnold; Yamashita, Naoyuki; Lambert, James L.; Stassun, Keivan G.; Beck, Patrick R.; Cherepy, Nerine J.; Payne, Stephen A.; Castillo-Rogez, Julie C.; Feldman, Sabrina M.; Raymond, Carol A.

    2016-09-01

    Gamma rays produced passively by cosmic ray interactions and by the decay of radioelements convey information about the elemental makeup of planetary surfaces and atmospheres. Orbital missions mapped the composition of the Moon, Mars, Mercury, Vesta, and now Ceres. Active neutron interrogation will enable and/or enhance in situ measurements (rovers, landers, and sondes). Elemental measurements support planetary science objectives as well as resource utilization and planetary defense initiatives. Strontium iodide, an ultra-bright scintillator with low nonproportionality, offers significantly better energy resolution than most previously flown scintillators, enabling improved accuracy for identification and quantification of key elements. Lanthanum bromide achieves similar resolution; however, radiolanthanum emissions obscure planetary gamma rays from radioelements K, Th, and U. The response of silicon-based optical sensors optimally overlaps the emission spectrum of strontium iodide, enabling the development of compact, low-power sensors required for space applications, including burgeoning microsatellite programs. While crystals of the size needed for planetary measurements (>100 cm3) are on the way, pulse-shape corrections to account for variations in absorption/re-emission of light are needed to achieve maximum resolution. Additional challenges for implementation of large-volume detectors include optimization of light collection using silicon-based sensors and assessment of radiation damage effects and energetic-particle induced backgrounds. Using laboratory experiments, archived planetary data, and modeling, we evaluate the performance of strontium iodide for future missions to small bodies (asteroids and comets) and surfaces of the Moon and Venus. We report progress on instrument design and preliminary assessment of radiation damage effects in comparison to technology with flight heritage.

  11. Electronic properties and Compton profiles of silver iodide

    Indian Academy of Sciences (India)

    Alpa Dashora; Ambica Marwal; K R Soni; B L Ahuja

    2010-06-01

    We have carried out an extensive study of electronic properties of silver iodide in - and -phases. The theoretical Compton profiles, energy bands, density of states and anisotropies in momentum densities are computed using density functional theories. We have also employed full-potential linearized augmented plane-wave method to derive the energy bands and the density of states. To compare our theoretical data, isotropic Compton profile measurement on -AgI using 137Cs Compton spectrometer at an intermediate resolution of 0.38 a.u. has been undertaken. The theoretical anisotropies are also interpreted on the basis of energy bands.

  12. Temperature dependent energy levels of methylammonium lead iodide perovskite

    Energy Technology Data Exchange (ETDEWEB)

    Foley, Benjamin J.; Marlowe, Daniel L.; Choi, Joshua J., E-mail: jjc6z@virginia.edu, E-mail: mgupta@virginia.edu, E-mail: scudiero@wsu.edu [Department of Chemical Engineering, University of Virginia, Charlottesville, Virginia 22904 (United States); Sun, Keye; Gupta, Mool C., E-mail: jjc6z@virginia.edu, E-mail: mgupta@virginia.edu, E-mail: scudiero@wsu.edu [Department of Electrical and Computer Engineering, University of Virginia, Charlottesville, Virginia 22904 (United States); Saidi, Wissam A. [Department of Mechanical Engineering and Materials Science, University of Pittsburgh, Pittsburgh, Pennsylvania 15261 (United States); Scudiero, Louis, E-mail: jjc6z@virginia.edu, E-mail: mgupta@virginia.edu, E-mail: scudiero@wsu.edu [Chemistry Department and Materials Science and Engineering Program, Washington State University, Pullman, Washington 99164 (United States)

    2015-06-15

    Temperature dependent energy levels of methylammonium lead iodide are investigated using a combination of ultraviolet photoemission spectroscopy and optical spectroscopy. Our results show that the valence band maximum and conduction band minimum shift down in energy by 110 meV and 77 meV as temperature increases from 28 °C to 85 °C. Density functional theory calculations using slab structures show that the decreased orbital splitting due to thermal expansion is a major contribution to the experimentally observed shift in energy levels. Our results have implications for solar cell performance under operating conditions with continued sunlight exposure and increased temperature.

  13. Polarized spectral complexes of optical functions of monovalent mercury iodide

    Science.gov (United States)

    Sobolev, V. V.; Sobolev, V. Val.; Anisimov, D. V.

    2015-12-01

    Spectral complexes of optical functions of monovalent mercury iodide Hg2I2 were determined for E ⊥ c and E || c polarizations in the range from 2 to 5.5 eV at 4.2 K. The permittivity and characteristic electron energy loss spectra were expanded in simple components with the determination of their main parameters, including the energy of the maximum and the oscillator strength. The calculations were performed based on known reflectance spectra. Computer programs based on Kramers-Kronig relations and the improved parameter-free method of Argand diagrams were used.

  14. Electrolytic coloration of hydroxyl-doped potassium iodide polycrystals

    Science.gov (United States)

    Wang, Na; Gu, Hongen; Han, Li; Guo, Meili; Qin, Fang

    2007-03-01

    Hydroxyl-doped potassium iodide polycrystals were successfully colored electrolytically by using a pointed cathode and a flat anode at various temperatures and electric field strengths, which mainly benefits appropriate coloration temperatures and electric field strengths. Characteristic OH-, O2--Va+ , U, V2, V3, Cu+, Cu-related, I2- , I2, K, F, R1 and R2 spectral bands were observed in Kubelka-Munk functions of the colored polycrystals, and the OH- and O2--Va+ spectral bands at room temperature were determined from Mollwo-Ivey plots. Color center formation in the electrolytic coloration was explained.

  15. Persistent Energetic Electrons in Methylammonium Lead Iodide Perovskite Thin Films.

    Science.gov (United States)

    Niesner, Daniel; Zhu, Haiming; Miyata, Kiyoshi; Joshi, Prakriti P; Evans, Tyler J S; Kudisch, Bryan J; Trinh, M Tuan; Marks, Manuel; Zhu, X-Y

    2016-12-07

    In conventional semiconductor solar cells, carriers are extracted at the band edges and the excess electronic energy (E*) is lost as heat. If E* is harvested, power conversion efficiency can be as high as twice the Shockley-Queisser limit. To date, materials suitable for hot carrier solar cells have not been found due to efficient electron/optical-phonon scattering in most semiconductors, but our recent experiments revealed long-lived hot carriers in single-crystal hybrid lead bromide perovskites. Here we turn to polycrystalline methylammonium lead iodide perovskite, which has emerged as the material for highly efficient solar cells. We observe energetic electrons with excess energy ⟨E*⟩ ≈ 0.25 eV above the conduction band minimum and with lifetime as long as ∼100 ps, which is 2-3 orders of magnitude longer than those in conventional semiconductors. The energetic carriers also give rise to hot fluorescence emission with pseudo-electronic temperatures as high as 1900 K. These findings point to a suppression of hot carrier scattering with optical phonons in methylammonium lead iodide perovskite. We address mechanistic origins of this suppression and, in particular, the correlation of this suppression with dynamic disorder. We discuss potential harvesting of energetic carriers for solar energy conversion.

  16. Ionic transport in hybrid lead iodide perovskite solar cells

    Science.gov (United States)

    Eames, Christopher; Frost, Jarvist M.; Barnes, Piers R. F.; O'Regan, Brian C.; Walsh, Aron; Islam, M. Saiful

    2015-01-01

    Solar cells based on organic–inorganic halide perovskites have recently shown rapidly rising power conversion efficiencies, but exhibit unusual behaviour such as current–voltage hysteresis and a low-frequency giant dielectric response. Ionic transport has been suggested to be an important factor contributing to these effects; however, the chemical origin of this transport and the mobile species are unclear. Here, the activation energies for ionic migration in methylammonium lead iodide (CH3NH3PbI3) are derived from first principles, and are compared with kinetic data extracted from the current–voltage response of a perovskite-based solar cell. We identify the microscopic transport mechanisms, and find facile vacancy-assisted migration of iodide ions with an activation energy of 0.6 eV, in good agreement with the kinetic measurements. The results of this combined computational and experimental study suggest that hybrid halide perovskites are mixed ionic–electronic conductors, a finding that has major implications for solar cell device architectures. PMID:26105623

  17. Numerical modelling of methyl iodide in the eastern tropical Atlantic

    Directory of Open Access Journals (Sweden)

    I. Stemmler

    2013-06-01

    Full Text Available Methyl iodide (CH3I is a volatile organic halogen compound that contributes significantly to the transport of iodine from the ocean to the atmosphere, where it plays an important role in tropospheric chemistry. CH3I is naturally produced and occurs in the global ocean. The processes involved in the formation of CH3I, however, are not fully understood. In fact, there is an ongoing debate whether production by phytoplankton or photochemical degradation of organic matter is the main source term. Here, both the biological and photochemical production mechanisms are considered in a biogeochemical module that is coupled to a one-dimensional water column model for the eastern tropical Atlantic. The model is able to reproduce observed subsurface maxima of CH3I concentrations. But, the dominating source process cannot be clearly identified as subsurface maxima can occur due to both direct biological and photochemical production. However, good agreement between the observed and simulated difference between surface and subsurface methyl iodide concentrations is achieved only when direct biological production is taken into account. Production rates for the biological CH3I source that were derived from published laboratory studies are shown to be inappropriate for explaining CH3I concentrations in the eastern tropical Atlantic.

  18. Nuclear detonation, thyroid cancer and potassium iodide prophylaxis

    Directory of Open Access Journals (Sweden)

    Viroj Wiwanitkit

    2011-01-01

    Full Text Available The recent nuclear disaster at Japan has raised global concerns about effects of radioactive leakage in the environment, associated hazards, and how they can be prevented. In this article, we have tried to explain about the guidelines laid down by World Health Organization for a potassium iodide prophylaxis following a nuclear disaster, and its mechanism of action in preventing thyroid cancer. Data was collected mainly from the studies carried out during the Chernobyl disaster of Russia in 1986 and the hazardous effects especially on the thyroid gland were studied. It was seen that radioactive iodine leakage from the nuclear plants mainly affected the thyroid gland, and especially children were at a higher risk at developing the cancers. Potassium Iodide prophylaxis can be administered in order to prevent an increase in the incidence of thyroid cancers in the population of an area affected by a nuclear disaster. However, one has to be cautious while giving it, as using it without indication has its own risks.

  19. Thyroid hormones and iodide in the near-term pregnant rat.

    NARCIS (Netherlands)

    Versloot, P.M.

    1998-01-01

    Thyroid hormones, thyroxine (T4) and 3,5,3'-triiodothyronine (T3), are produced by the thyroid gland. To synthesize thyroid hormones the thyroid needs iodide. The uptake of iodide as well as the production and secretion of T4 and T3 by the thyroid gland is regulated by thyrotropin (TSH), which is pr

  20. Effects of radiation and temperature on iodide sorption by surfactant-modified bentonite.

    Science.gov (United States)

    Choung, Sungwook; Kim, Minkyung; Yang, Jung-Seok; Kim, Min-Gyu; Um, Wooyong

    2014-08-19

    Bentonite, which is used as an engineered barrier in geological repositories, is ineffective for sorbing anionic radionuclides because of its negatively charged surface. This study modified raw bentonite using a cationic surfactant (i.e., hexadecyltrimethylammonium [HDTMA]-Br) to improve its sorption capability for radioactive iodide. The effects of temperature and radiation on the iodide sorption of surfactant-modified bentonite (SMB) were also evaluated under alkaline pH condition similar to that found in repository environments. Different amounts of surfactant, equivalent to the 50, 100, and 200% cation-exchange capacity of the bentonite, were used to produce the HDTMA-SMB for iodide sorption. The sorption reaction of the SMB with iodide reached equilibrium rapidly within 10 min regardless of temperature and radiation conditions. The rate of iodide sorption increased as the amount of the added surfactant was increased and nonlinear sorption behavior was exhibited. However, high temperature and γ-irradiation ((60)Co) resulted in significantly (∼2-10 times) lower iodide Kd values for the SMB. The results of FTIR, NMR, and XANES spectroscopy analysis suggested that the decrease in iodide sorption may be caused by weakened physical electrostatic force between the HDTMA and iodide, and by the surfactant becoming detached from the SMB during the heating and irradiation processes.

  1. Tungstosilicic Acid: An Efficient and Ecofriendly Catalyst for the Conversion of Alcohols to Alkyl Iodides

    Directory of Open Access Journals (Sweden)

    Masoud Mokhtary

    2011-01-01

    Full Text Available Treatment of a range of benzylic, allylic, and secondary aliphatic alcohols with potassium iodides in the presence of H4SiW12O40 affords the corresponding alkyl iodides in good to excellent yield with straightforward purification at room temperature in CH3CN.

  2. Bibenzimidazole containing mixed ligand cobalt(III) complex as a selective receptor for iodide

    Digital Repository Service at National Institute of Oceanography (India)

    Indumathy, R.; Parameswarana, P.S.; Aiswarya, C.V.; Nair, B.U.

    -, OH- and OAc- do not bring about any dramatic visual colorimetric changes. However, metallo-receptor 2 brings about vivid color change with iodide anion visually and this could be due to charge transfer transition via ion pair formation with iodide ion...

  3. CuI-catalyzed Synthesis of Aryl Thiocyanates from Aryl Iodides

    Institute of Scientific and Technical Information of China (English)

    Ye Feng WANG; Yuan ZHOU; Jia Rui WANG; Lei LIU; Qing Xiang GUO

    2006-01-01

    An operationally simple and inexpensive catalyst system was developed for the cross coupling of potassium thiocyanate with aryl iodides by using CuI as catalyst, 1, 10-phenanthroline as ligand, and tetraethylammonium iodide as activator. The procedure is applicable for the synthesis of diverse aryl thiocyanates without any exotic, poisonous reagents.

  4. Determination of Trace Iodide in Sodium Bisulfite Aqueous Solution by Ion Chromatography with UV Detection

    Energy Technology Data Exchange (ETDEWEB)

    Park, Y.S.; Kim, D.Y.; Choi, K.S.; Park, S.D.; Han, S.H. [Korea Atomic Energy Research Institute, Taejon (Korea)

    2000-06-01

    The iodide was recovered from a simulated spent fuel to the sodium bisulfite aqueous solution. It was discussed that the trace iodide (below 1 ppm) was determined without the matrix effect of 0.1 M sodium bisulfite and 1 mM HNO{sub 3} in aqueous solution by ion chromatography with UV detection. AS4A-SC(DIONEX) column and UV-absorption spectrophotometer were used. The UV-absorption spectra of sodium bisulfite nitric acid and iodide were obtained, and then 230 nm was selected as an absorption wavelength for iodide determination. 0.1 M NaCl eluent was optimum condition. In this condition the calibration curve of iodide was obtained on the range of about 0-1,000 ppb. The linear coefficient was 0.99993 and the detection limit was 5 ppb. The relative standard deviation was 1.26%. (author). 17 refs., 3 tabs., 4 figs.

  5. The Determination of Iodide Based on a Flow-injection Coupling Irreversible Biamperometry

    Institute of Scientific and Technical Information of China (English)

    Li Jun LI; Hao CHENG; Wen Yi HUANG; Hong Xing KONG; Jian Ling WU; Jian Ping LU; Wei GAO; Jun Feng SONG

    2005-01-01

    A novel flow-injection irreversible biamperometric method is described for the direct determination of iodide. The method is based on electrochemical oxidation of iodide at the gold electrode and the reduction of permanganate at the platinum electrode to form an irreversible biamperometric detection system. Under the applied potential difference of 0 V, in the 0.05mol/L sulfuric acid, iodide can be determined over the range 4.00×10-7-l.00×l0-5 mol/L with a sampling frequency of 120 samples per hour. The detection limit for Ⅰ- is 3.0× 10-7 mol/L and the RSD for 40 replicate determinations of 4.0×10-5 mol/L potassium iodide is 1.68%. The new method was applied to the analysis of iodide in table salt with satisfactory results.

  6. Synthesis, growth, structural, thermal, optical properties of new metal-organic crystals: Methyltriphenylphosphonium iodide thiourea and methyltriphenylphosphonium iodide chloroform hemisolvate

    Science.gov (United States)

    Shivachev, Boris L.; Kossev, Krassimir; Dimowa, Louiza T.; Yankov, Georgi; Petrov, Todor; Nikolova, Rositsa P.; Petrova, Nadia

    2013-08-01

    Crystals of methyltriphenylphosphonium iodide thiourea (1) and methyltriphenylphosphonium iodide chloroform hemisolvate (2) were obtained for the first time. Fourier transform infrared (FTIR) spectral studies have been performed to identify the functional groups. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) were used to study their thermal properties. The optical transmittance window and the lower cutoff wavelength have been identified by UV-vis studies. Crystals of the title compounds suitable for single crystal X-ray analyses were successfully grown by slow evaporation and diffraction data were collected to elucidate the molecular structure and interactions. The proton donors (phosphonium) and proton acceptor (iodine) in the structure of 1 provide infrastructure to introduce charge asymmetry while in 2 chloroform molecule is not involved in the charge transfer. An optical quality crystal of 1 (5×4×2 mm3) was obtained by macroseeding. The crystal has developed facets with major ones (001) and (00¯1). A crystal of 1 was tested with 1060 nm laser radiation and showed second harmonic generation (SHG).

  7. Fabrication of Efficient Low-Bandgap Perovskite Solar Cells by Combining Formamidinium Tin Iodide with Methylammonium Lead Iodide

    Energy Technology Data Exchange (ETDEWEB)

    Liao, Weiqiang; Zhao, Dewei; Yu, Yue; Shrestha, Niraj; Ghimire, Kiran; Grice, Corey R.; Wang, Changlei; Xiao, Yuqing; Cimaroli, Alexander J.; Ellingson, Randy J.; Podraza, Nikolas J.; Zhu, Kai; Xiong, Ren-Gen; Yan, Yanfa

    2016-09-28

    Mixed tin (Sn)-lead (Pb) perovskites with high Sn content exhibit low bandgaps suitable for fabricating the bottom cell of perovskite-based tandem solar cells. In this work, we report on the fabrication of efficient mixed Sn-Pb perovskite solar cells using precursors combining formamidinium tin iodide (FASnI3) and methylammonium lead iodide (MAPbI3). The best-performing cell fabricated using a (FASnI3)0.6(MAPbI3)0.4 absorber with an absorption edge of ~1.2 eV achieved a power conversion efficiency (PCE) of 15.08 (15.00)% with an open-circuit voltage of 0.795 (0.799) V, a short-circuit current density of 26.86(26.82) mA/cm2, and a fill factor of 70.6(70.0)% when measured under forward (reverse) voltage scan. The average PCE of 50 cells we have fabricated is 14.39 +/- 0.33%, indicating good reproducibility.

  8. Horizontal Ampoule Growth and Characterization of Mercuric Iodide at Controlled Gas Pressures for X-Ray and Gamma Ray Spectrometers

    Energy Technology Data Exchange (ETDEWEB)

    McGregor, Douglas S. [Kansas State Univ., Manhattan, KS (United States). Semiconductor Materials and Radiological Technologies Lab., Dept. of Nuclear and Mechanical Engineering; Ariesanti, Elsa [Kansas State Univ., Manhattan, KS (United States). Semiconductor Materials and Radiological Technologies Lab., Dept. of Nuclear and Mechanical Engineering; Corcoran, Bridget [Kansas State Univ., Manhattan, KS (United States). Semiconductor Materials and Radiological Technologies Lab., Dept. of Nuclear and Mechanical Engineering

    2004-04-30

    The project developed a new method for producing high quality mercuric iodide crystals of x-ray and gamma spectrometers. Included are characterization of mercuric iodide crystal properties as a function of growth environment and fabrication and demonstration of room-temperature-operated high-resolution mercuric iodide spectrometers.

  9. Morphological effects in the quantum yield of cesium iodide

    Energy Technology Data Exchange (ETDEWEB)

    Almeida, J. [Ecole Politechnique Federale, Lausanne (Switzerland). DP-IPA PH-Ecublens; Barbo, F. [Sincrotrone Trieste SpA, Padriciano 99, 34012 Trieste (Italy); Bertolo, M. [Sincrotrone Trieste SpA, Padriciano 99, 34012 Trieste (Italy); Bianco, A. [Sincrotrone Trieste SpA, Padriciano 99, 34012 Trieste (Italy); Braem, A. [European Organization for Nuclear Research, Geneva (Switzerland). Div. Particle Physics Experiments; Cerasari, S. [Sincrotrone Trieste SpA, Padriciano 99, 34012 Trieste (Italy); Coluzza, C. [Ecole Politechnique Federale, Lausanne (Switzerland). DP-IPA PH-Ecublens; Dell`Orto, T. [Ecole Politechnique Federale, Lausanne (Switzerland). DP-IPA PH-Ecublens; Fontana, S. [Sincrotrone Trieste SpA, Padriciano 99, 34012 Trieste (Italy); Margaritondo, G. [Ecole Politechnique Federale, Lausanne (Switzerland). DP-IPA PH-Ecublens; Nappi, E. [Istituto Nazionale di Fisica Nucleare, Bari (Italy); Paic, G. [European Organization for Nuclear Research, Geneva (Switzerland). Div. Particle Physics Experiments; Piuz, F. [European Organization for Nuclear Research, Geneva (Switzerland). Div. Particle Physics Experiments; Sanjines, R. [Ecole Politechnique Federale, Lausanne (Switzerland). DP-IPA PH-Ecublens; Scognetti, T. [Istituto Nazionale di Fisica Nucleare, Bari (Italy); Sgobba, S. [European Organization for Nuclear Research, Geneva (Switzerland). Div. Particle Physics Experiments

    1995-07-15

    We demonstrated that polycrystalline cesium iodide (CsI) on large area Ni/Au coated printed board provides a quantum efficiency (QE) higher by a factor of 2 than the films deposited on the standard Cu/Au printed circuits. This is the most important result of the present systematic study of the QE lateral inhomogeneity for CsI on different substrates. We found a strong correlation between the QE lateral variation and the morphological homogeneity of the films. The QE was measured by UV photoelectron emission microscopy and spatially resolved X-ray photoemission, and the morphology studies were performed by secondary electron microscopy, X-ray diffraction and scanning tunneling microscopy. (orig.).

  10. Electronic characterization of mercuric iodide gamma ray spectrometers

    Energy Technology Data Exchange (ETDEWEB)

    Gerrish, V.M.

    1993-01-01

    During the past four years the yield of high resolution mercuric iodide (HgI[sub 2]) gamma ray spectrometers produced at EG G/EM has increased dramatically. Data is presented which demonstrates a strong correlation between starting material and spectrometer performance. Improved spectrometer yields are attributed to the method of HgI[sub 2] synthesis and to material purification procedures. Data is presented which shows that spectrometer performance is correlated with hole mobility-lifetime products. In addition, the measurement of Schottky barrier heights on HgI[sub 2] spectrometers has been performed using I-V curves and the photoelectric method. Barrier heights near 1.1 eV have been obtained using various contacts and contact deposition methods. These data suggest the pinning of the Fermi level at midgap at the HgI[sub 2] surface, probably due to surface states formed prior to contact deposition.

  11. Electronic characterization of mercuric iodide gamma ray spectrometers

    Energy Technology Data Exchange (ETDEWEB)

    Gerrish, V.M.

    1993-06-01

    During the past four years the yield of high resolution mercuric iodide (HgI{sub 2}) gamma ray spectrometers produced at EG&G/EM has increased dramatically. Data is presented which demonstrates a strong correlation between starting material and spectrometer performance. Improved spectrometer yields are attributed to the method of HgI{sub 2} synthesis and to material purification procedures. Data is presented which shows that spectrometer performance is correlated with hole mobility-lifetime products. In addition, the measurement of Schottky barrier heights on HgI{sub 2} spectrometers has been performed using I-V curves and the photoelectric method. Barrier heights near 1.1 eV have been obtained using various contacts and contact deposition methods. These data suggest the pinning of the Fermi level at midgap at the HgI{sub 2} surface, probably due to surface states formed prior to contact deposition.

  12. Dual frequency cavitation event sensor with iodide dosimeter.

    Science.gov (United States)

    Ebrahiminia, Ali; Mokhtari-Dizaji, Manijhe; Toliyat, Tayebeh

    2016-01-01

    The inertial cavitation activity depends on the sonication parameters. The purpose of this work is development of dual frequency inertial cavitation meter for therapeutic applications of ultrasound waves. In this study, the chemical effects of sonication parameters in dual frequency sonication (40 kHz and 1 MHz) were investigated in the progressive wave mode using iodide dosimetry. For this purpose, efficacy of different exposure parameters such as intensity, sonication duration, sonication mode, duty factor and net ultrasound energy on the inertial cavitation activity have been studied. To quantify cavitational effects, the KI dosimeter solution was sonicated and its absorbance at a wavelength of 350 nm was measured. The absorbance values in continuous sonication mode was significantly higher than the absorbance corresponding to the pulsed mode having duty factors of 20-80% (plevel intensity (sensor can be useful for ultrasonic treatments.

  13. Development of mercuric iodide detectors for XAS and XRD measurements

    Energy Technology Data Exchange (ETDEWEB)

    Warburton, W.K.; Iwanczyk, J.S.; Dabrowski, A.J.; Hedman, B.; Penner-Hakn, J.E.; Roe, A.L.; Hodgson, K.O.; Beyerle, A.

    1985-07-01

    A prototype element for an energy dispersive detector (EDD) array was constructed using a Mercuric Iodide detector. Both detector and front end FET could be thermoelectrically cooled. Tested at SSRL, the detector had 250 eV electronic noise and 315 eV resolution at 5.9 keV. K line fluorescence spectra were collected for selected elements between Cl (2622 eV) and Zn (8638 eV). Count rate capability to 60,000 cps was demonstrated. Several detector parameters were measured, including energy linearity, resolution vs. shaping time, and detector dead time. An EXAFS (extended x-ray absorption fine structure) spectrum was recorded and compared to simultaneously collected transmission data.

  14. Radiative efficiency of lead iodide based perovskite solar cells

    Science.gov (United States)

    Tvingstedt, Kristofer; Malinkiewicz, Olga; Baumann, Andreas; Deibel, Carsten; Snaith, Henry J.; Dyakonov, Vladimir; Bolink, Henk J.

    2014-08-01

    The maximum efficiency of any solar cell can be evaluated in terms of its corresponding ability to emit light. We herein determine the important figure of merit of radiative efficiency for Methylammonium Lead Iodide perovskite solar cells and, to put in context, relate it to an organic photovoltaic (OPV) model device. We evaluate the reciprocity relation between electroluminescence and photovoltaic quantum efficiency and conclude that the emission from the perovskite devices is dominated by a sharp band-to-band transition that has a radiative efficiency much higher than that of an average OPV device. As a consequence, the perovskite have the benefit of retaining an open circuit voltage ~0.14 V closer to its radiative limit than the OPV cell. Additionally, and in contrast to OPVs, we show that the photoluminescence of the perovskite solar cell is substantially quenched under short circuit conditions in accordance with how an ideal photovoltaic cell should operate.

  15. Development of w/o microemulsion for transdermal delivery of iodide ions.

    Science.gov (United States)

    Lou, Hao; Qiu, Ni; Crill, Catherine; Helms, Richard; Almoazen, Hassan

    2013-03-01

    The objective of this study was to develop a water-in-oil (w/o) microemulsion which can be utilized as a transdermal delivery for iodide ions. Several w/o microemulsion formulations were prepared utilizing Span 20, ethanol, Capryol 90®, and water. The selected formulations had 5%, 10%, 15%, 20%, and a maximum of 23% w/w water content. Potassium iodide (KI) was incorporated in all formulations at 5% w/v. Physicochemical characterizations were conducted to evaluate the structure and stability. These studies included: mean droplet size, pH, viscosity, conductivity, and chemical stability tests. In vitro human skin permeation studies were conducted to evaluate the diffusion of the iodide ion through human skin. The w/o microemulsion formulations were stable and compatible with iodide ions with water content ranging from 5% to 23% w/w. The addition of KI influenced the physicochemical properties of microemulsion as compared to blank microemulsion formulations. In vitro human skin permeation studies indicated that selected formulations improved iodide ion diffusion significantly as compared to control (KI solution; P valueIodide ions were entrapped within the aqueous core of w/o microemulsion. Span 20, ethanol and Capryol 90 protected the iodide ions against oxidation and formed a stable microemulsion. It is worth to note that according to Hofmeister series, iodide ions tend to lower the interfacial tension between water and oil and consequently enhance overall stability. This work illustrates that microemulsion system can be utilized as a vehicle for the transdermal administration of iodide.

  16. A Direct Transformation of Aryl Aldehydes to Benzyl Iodides Via Reductive Iodination

    Energy Technology Data Exchange (ETDEWEB)

    Ruso, Jayaraman Sembian; Rajendiran, Nagappan; Kumaran, Rajendran Senthil [Univ. of Madras, Chennai (India)

    2014-02-15

    A facile transformation of aryl aldehydes to benzyl iodides through one-pot reductive iodination is reported. This protocol displays remarkable functional group tolerance and the title compound was obtained in good to excellent yield.

  17. Kinetics and mechanism of the mercury(II)-assisted hydrolysis of methyl iodide.

    Science.gov (United States)

    Celo, Valbona; Scott, Susannah L

    2005-04-01

    The kinetics and mechanism of the reaction of aqueous Hg(II) with methyl iodide have been investigated. The overall reaction is best described as Hg(II)-assisted hydrolysis, resulting in quantitative formation of methanol and, in the presence of excess methyl iodide, ultimately, HgI2 via the intermediate HgI+. The kinetics are biexponential when methyl iodide is in excess. At 25 degrees C, the acceleration provided by Hg2+ is 7.5 times greater than that caused by HgI+, while assistance of hydrolysis was not observed for HgI2. Thus, the reactions are not catalytic in Hg(II). The kinetics are consistent with an SN2-M+ mechanism involving electrophilic attack at iodide. As expected, methylation of mercury is not a reaction pathway; traces of methylmercury(II) are artifacts of the extraction/preconcentration procedure used for methylmercury analysis.

  18. Fluorescence characteristics of 5-amino salicylic acid: An iodide recognition study

    Science.gov (United States)

    Arora, Priyanka; Suyal, Kanchan; Joshi, Neeraj K.; Joshi, Hem Chandra; Pant, Sanjay

    In this paper we report the effect of iodide on the fluorescence of 5-amino salicylic acid (5-ASA). In the absence of iodide, prominent blue green (BG) emission band at ˜465 nm (broad) is observed in aprotic solvents whereas violet (V) emission at ˜408 nm, blue green (BG) at ˜480 nm and green (G) at ˜500 nm are observed in case of protic solvents. On the addition of iodide ion (I-), the intensity of BG fluorescence is enhanced in case of aprotic solvents. On the other hand the G band is enhanced in protic solvents and decrease in the intensity of the V band is observed. The effect of hydrogen bonding as well as the interplay of neutral and ionic species is invoked to explain the observed results. The study projects the application of this system in iodide recognition in protic/aprotic environments.

  19. Horseradish Peroxidase-Mediated, Iodide-Catalyzed Cascade Reaction for Plasmonic Immunoassays.

    Science.gov (United States)

    Xianyu, Yunlei; Chen, Yiping; Jiang, Xingyu

    2015-11-01

    This report outlines an enzymatic cascade reaction for signal transduction and amplification for plasmonic immunoassays by using horseradish peroxidase (HRP)-mediated aggregation of gold nanoparticles (AuNPs). HRP-catalyzed oxidation of iodide and iodide-catalyzed oxidation of cysteine is employed to modulate the plasmonic signals of AuNPs. It agrees well with the current immunoassay platforms and allows naked-eye readout with enhanced sensitivity, which holds great promise for applications in resource-constrained settings.

  20. Air-Driven Potassium Iodide-Mediated Oxidative Photocyclization of Stilbene Derivatives.

    Science.gov (United States)

    Matsushima, Tomoya; Kobayashi, Sayaka; Watanabe, Soichiro

    2016-09-02

    A new method has been developed for the potassium iodide-mediated oxidative photocyclization of stilbene derivatives. Compared with conventional iodine-mediated oxidative photocyclization reactions, this new method requires shorter reaction times and affords cyclized products in yields of 45-97%. This reaction proceeds with a catalytic amount of potassium iodide and works in an air-driven manner without the addition of an external scavenger. The radical-mediated oxidative photocyclization of stilbene derivatives using TEMPO was also investigated.

  1. [Study on the stability of potassium iodide of the iodized salt].

    Science.gov (United States)

    Voudouris, E

    1975-04-29

    The stability of potassium iodide in iodized salt has been studied with respect to the purity of the salt used as raw material. It has been found that the iodized salt prepared from high purity salt and preserved under proper conditions (protection from light, humidity and high temperatures) keeps, for several months, the most of the initially added potassium iodide, without any addition of stabilizers, except for a small bicarbonate.

  2. Permeation of iodide from iodine-enriched yeast through porcine intestine.

    Science.gov (United States)

    Ryszka, Florian; Dolińska, Barbara; Zieliński, Michał; Chyra, Dagmara; Dobrzański, Zbigniew

    2013-01-01

    Iodine deficiency is a common phenomenon, threatening the whole global human population. Recommended daily intake of iodine is 150 μg for adults and 250 μg for pregnant and breastfeeding women. About 50% of human population can be at risk of moderate iodine deficiency. Due to this fact, increased iodine supplementation is recommended, through intake of iodized mineral water and salt iodization. The aim of this study was to investigate permeation and absorption of iodide from iodine bioplex (experimental group) in comparison with potassium iodide (controls). Permeation and absorption processes were investigated in vitro using a porcine intestine. The experimental model was based on a standard Franz diffusion cell (FD-Cell). The iodine bioplex was produced using Saccharomyces cerevisiae yeast and whey powder: iodine content - 388 μg/g, total protein - 28.5%, total fat - 0.9%., glutamic acid - 41.2%, asparaginic acid - 29.4%, lysine - 24.8%; purchased from: F.Z.N.P. Biochefa, Sosnowiec, Poland. Potassium iodide was used as controls, at 388 μg iodine concentration, which was the same as in iodine-enriched yeast bioplex. A statistically significant increase in iodide permeation was observed for iodine-enriched yeast bioplex in comparison with controls - potassium iodide. After 5h the total amount of permeated iodide from iodine-enriched yeast bioplex was 85%, which is ~ 2-fold higher than controls - 37%. Iodide absorption was by contrast statistically significantly higher in controls - 7.3%, in comparison with 4.5% in experimental group with iodine-enriched yeast bioplex. Presented results show that iodide permeation process dominates over absorption in case of iodine-enriched yeast bioplex.

  3. Modelling iodide – iodate speciation in atmospheric aerosol: Contributions of inorganic and organic iodine chemistry

    Directory of Open Access Journals (Sweden)

    S. Pechtl

    2007-01-01

    Full Text Available The speciation of iodine in atmospheric aerosol is currently poorly understood. Models predict negligible iodide concentrations but accumulation of iodate in aerosol, both of which is not confirmed by recent measurements. We present an updated aqueous phase iodine chemistry scheme for use in atmospheric chemistry models and discuss sensitivity studies with the marine boundary layer model MISTRA. These studies show that iodate can be reduced in acidic aerosol by inorganic reactions, i.e., iodate does not necessarily accumulate in particles. Furthermore, the transformation of particulate iodide to volatile iodine species likely has been overestimated in previous model studies due to negligence of collision-induced upper limits for the reaction rates. However, inorganic reaction cycles still do not seem to be sufficient to reproduce the observed range of iodide – iodate speciation in atmospheric aerosol. Therefore, we also investigate the effects of the recently suggested reaction of HOI with dissolved organic matter to produce iodide. If this reaction is fast enough to compete with the inorganic mechanism, it would not only directly lead to enhanced iodide concentrations but, indirectly via speed-up of the inorganic iodate reduction cycles, also to a decrease in iodate concentrations. Hence, according to our model studies, organic iodine chemistry, combined with inorganic reaction cycles, is able to reproduce observations. The presented chemistry cycles are highly dependent on pH and thus offer an explanation for the large observed variability of the iodide – iodate speciation in atmospheric aerosol.

  4. Mechanistic aspects of ingested chlorine dioxide on thyroid function: impact of oxidants on iodide metabolism

    Energy Technology Data Exchange (ETDEWEB)

    Bercz, J.P.; Jones, L.L.; Harrington, R.M.; Bawa, R.; Condie, L.

    1986-11-01

    Toxicological studies dealing with recent findings of health effects of drinking water disinfectants are reviewed. Experiments with monkeys and rodents indicate that the biological activity of ingested disinfectants is expressed via their chemical interaction with the mucosal epithelia, secretory products, and nutritional contents of the alimentary tract. Evidence exists that a principal partner of this redox interaction is the iodide of nutritional origin that is ubiquitous in the gastrointestinal tract. Thus the observation that subchronic exposure to chlorine dioxide (ClO/sub 2/) in drinking water decreases serum thyroxine levels in mammalian species can be best explained with changes produced in the chemical form of the bioavailable iodide. Ongoing and previously reported mechanistic studies indicate that oxidizing agents such as chlorine-based disinfectants oxidize the basal iodide content of the gastrointestinal tract. The resulting reactive iodine species readily attaches to organic matter by covalent bonding. Evidence suggests that the extent to which such iodinated organics are formed is proportional to the magnitude of the electromotive force and stoichiometry of the redox couple between iodide and the disinfectant. Because the extent of thyroid uptake of the bioavailable iodide does not decrease during ClO/sub 2/ ingestion, it seems that ClO/sub 2/ does not cause iodide deficiency of sufficient magnitude to account for the decease in hormonogenesis. Absorption of one or more of iodinated molecules, e.g., nutrient, hormones, or cellular constituents of the alimentary tract having thyromimetic or thyroid inhibitory properties, is a better hypothesis for the effects seen.

  5. Lead iodide X-ray and gamma-ray spectrometers for room and high temperature operation

    Energy Technology Data Exchange (ETDEWEB)

    Hermon, H.; James, R.B.; Cross, E. [and others

    1997-02-01

    In this study, we report on the results of the investigation of lead iodide material properties. The effectiveness of zone refining purification methods on the material purity is determined by ICP-MS and ICP-OES and correlated to the electrical and physical material properties. We show that this zone refining method is very efficient in removing impurities from lead iodide and we also determine the segregation coefficient for some of these impurities. Triple axis x- ray diffraction (TAD) analysis has been used to determine the crystalline perfection of the lead iodide after applying various cutting, etching, and fabrication methods. The soft lead iodide crystal was found to be damaged when cleaved by a razor blade, but by using a diamond wheel saw, followed by etching, the crystallinity of the material was improved, as observed by TAD. Low temperature photoluminescence also indicates an improvement in the material properties of the purified lead iodide. Electrical properties of lead iodide such as carrier mobility, were calculated based on carrier- phonon scattering. The results for the electrical properties were in good agreement with the experimental data.

  6. Critical evaluation of acetylthiocholine iodide and acetylthiocholine chloride as substrates for amperometric biosensors based on acetylcholinesterase.

    Science.gov (United States)

    Bucur, Madalina-Petruta; Bucur, Bogdan; Radu, Gabriel-Lucian

    2013-01-25

    Numerous amperometric biosensors have been developed for the fast analysis of neurotoxic insecticides based on inhibition of cholinesterase (AChE). The analytical signal is quantified by the oxidation of the thiocholine that is produced enzymatically by the hydrolysis of the acetylthiocholine pseudosubstrate. The pseudosubstrate is a cation and it is associated with chloride or iodide as corresponding anion to form a salt. The iodide salt is cheaper, but it is electrochemically active and consequently more difficult to use in electrochemical analytical devices. We investigate the possibility of using acetylthiocholine iodide as pseudosubstrate for amperometric detection. Our investigation demonstrates that operational conditions for any amperometric biosensor that use acetylthiocholine iodide must be thoroughly optimized to avoid false analytical signals or a reduced sensitivity. The working overpotential determined for different screen-printed electrodes was: carbon-nanotubes (360 mV), platinum (560 mV), gold (370 mV, based on a catalytic effect of iodide) or cobalt phthalocyanine (110 mV, but with a significant reduced sensitivity in the presence of iodide anions).

  7. Stability and electronic properties of two-dimensional indium iodide

    Science.gov (United States)

    Wang, Jizhang; Dong, Baojuan; Guo, Huaihong; Yang, Teng; Zhu, Zhen; Hu, Gan; Saito, Riichiro; Zhang, Zhidong

    2017-01-01

    Based on ab initio density functional calculations, we studied the stability and electronic properties of two-dimensional indium iodide (InI). The calculated results show that monolayer and few-layer InI can be as stable as its bulk counterpart. The stability of the monolayer structure is further supported by examining the electronic and dynamic stability. The interlayer interaction is found to be fairly weak (˜160 meV/atom) and mechanical exfoliation to obtain monolayer and few-layer structures will be applicable. A direct band gap of 1.88 eV of the bulk structure is obtained from the hybrid functional method, and is comparable to the experimental one (˜2.00 eV). The electronic structure can be tuned by layer stacking and external strain. The size of the gap is a linear function of an inverse number of layers, suggesting that we can design few-layer structures for optoelectronic applications in the visible optical range. In-plane tensile or hydrostatic compressive stress is found to be useful not only in varying the gap size to cover the whole visible optical range, but also in inducing a semiconductor-metal transition with an experimentally accessible stress. The present result strongly supports the strategy of broadening the scope of group-V semiconductors by looking for isoelectronic III-VII atomic-layered materials.

  8. Persistent photovoltage in methylammonium lead iodide perovskite solar cells

    Science.gov (United States)

    Baumann, A.; Tvingstedt, K.; Heiber, M. C.; Väth, S.; Momblona, C.; Bolink, H. J.; Dyakonov, V.

    2014-08-01

    We herein perform open circuit voltage decay (OCVD) measurements on methylammonium lead iodide (CH3NH3PbI3) perovskite solar cells to increase the understanding of the charge carrier recombination dynamics in this emerging technology. Optically pulsed OCVD measurements are conducted on CH3NH3PbI3 solar cells and compared to results from another type of thin-film photovoltaics, namely, the two reference polymer-fullerene bulk heterojunction solar cell devices based on P3HT:PC60BM and PTB7:PC70BM blends. We observe two very different time domains of the voltage transient in the perovskite solar cell with a first drop on a short time scale that is similar to the decay in the studied organic solar cells. However, 65%-70% of the maximum photovoltage persists on much longer timescales in the perovskite solar cell than in the organic devices. In addition, we find that the recombination dynamics in all time regimes are dependent on the starting illumination intensity, which is also not observed in the organic devices. We then discuss the potential origins of these unique behaviors.

  9. Structural Effects on the Bandstructure of Methylammonium Lead Iodide

    Science.gov (United States)

    Bernardi, Marco; Barker, Bradford A.; Vigil-Fowler, Derek; Neaton, Jeffrey B.; Louie, Steven G.; Louie Team

    Metal-organic halide perovskites possess peculiar physical properties. The carrier diffusion length in methylammonium lead iodide (MAPbI) exceeds 1 μm, but this unusually high value for a solution-processed material is poorly understood. We developed first-principles calculations of carrier lifetimes and diffusion lengths in semiconductors, which require accurate knowledge of the bandstructure. In this talk, we show that in MAPbI the structure strongly affects the bandstructure and band edges, and that density functional theory (DFT) is unable to predict the room temperature tetragonal structure due to the polymorphism of MAPbI. The Rashba splitting induced by the spin-orbit interaction, and the DFT band gap and effective masses, all depend strongly on the chosen structure, a point that previous work failed to address. Working with multiple stochastic realizations of large unit cells with random methylammonium orientations, we compute average effective masses and show that the effective mass depends linearly on the band gap. The average Rashba coefficient we find is an order of magnitude smaller than previously reported, and the band edges are almost parabolic. Our structures possess the correct symmetry and are free of the spurious Pb off-centering assumed in previous work. We identify the correct starting point for GW bandstructure calculations and to compute the carrier lifetime and diffusion length.

  10. Chloride, bromide and iodide scintillators with europium doping

    Science.gov (United States)

    Zhuravleva, Mariya; Yang, Kan

    2014-08-26

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  11. Imaging with polycrystalline mercuric iodide detectors using VLSI readout

    Energy Technology Data Exchange (ETDEWEB)

    Turchetta, R.; Dulinski, W.; Husson, D.; Riester, J.L.; Schieber, M.; Zuck, A.; Melekhov, L.; Saado, Y.; Hermon, H.; Nissenbaum, J

    1999-06-01

    Potentially low cost and large area polycrystalline mercuric iodide room-temperature radiation detectors, with thickness of 100-600 {mu}m have been successfully tested with dedicated low-noise, low-power mixed signal VLSI electronics which can be used for compact, imaging solutions. The detectors are fabricated by depositing HgI{sub 2} directly on an insulating substrate having electrodes in the form of microstrips and pixels with an upper continuous electrode. The deposition is made either by direct evaporation or by screen printing HgI{sub 2} mixed with glue such as Poly-Vinyl-Butiral. The properties of these first-generation detectors are quite uniform from one detector to another. Also for each single detector the response is quite uniform and no charge loss in the inter-electrode space have been detected. Because of the low cost and of the polycrystallinity, detectors can be potentially fabricated in any size and shape, using standard ceramic technology equipment, which is an attractive feature where low cost and large area applications are needed. The detectors which act as radiation counters have been tested with a beta source as well as in a high-energy beam of 100 GeV muons at CERN, connected to VLSI, low noise electronics. Charge collection efficiency and uniformity have been studied. The charge is efficiently collected even in the space between strips indicating that fill factors of 100% could be reached in imaging applications with direct detection of radiation. Single photon counting capability is reached with VLSI electronics. These results show the potential of this material for applications demanding position sensitive, radiation resistant, room-temperature operating radiation detectors, where position resolution is essential, as it can be found in some applications in high-energy physics, nuclear medicine and astrophysics.

  12. Effect of Excessive Potassium Iodide on Rat Aorta Endothelial Cells.

    Science.gov (United States)

    Zhang, Man; Zou, Xiaoyan; Lin, Xinying; Bian, Jianchao; Meng, Huicui; Liu, Dan

    2015-08-01

    The aim of the current study was to investigate the effect of excess iodine on rat aorta endothelial cells and the potential underlying mechanisms. Rat aorta endothelial cells were cultured with iodide ion (3506, 4076, 4647, 5218, 5789, 6360, 6931, and 7512 mg/L) for 48 h. Morphological changes of cells were observed with microscope after Wright-Giemsa staining and acridine orange staining. Cell proliferation was determined with 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay, and cell apoptosis was assessed with flow cytometry. The activity of superoxide dismutase (SOD), glutathione peroxidase (GSH-Px), endothelial nitric oxide synthase (eNOS), induced nitric oxide synthase (iNOS), and concentrations of malondialdehyde (MDA), glutathione (GSH), and protein carbonyl in culture medium were determined with colorimetric method. The expression of intercellular adhesion molecule-1 (ICAM-1) and vascular cell adhesion molecule-1 (VCAM-1) was detected by enzyme linked immunosorbent assay. The results showed that excess iodine induced abnormal morphologic changes of cells, inhibited cell proliferation, and increased apoptosis rate. Iodine also reduced the activity of SOD, GSH-Px, and concentrations of GSH and increased the concentrations of MDA and protein carbonyl in a dose-dependent manner. Moreover, excess iodine decreased the activity of eNOS and increased the activity of iNOS and the expression of ICAM-1 and VCAM-1 in culture medium. Our results suggested that excess iodine exposure increased oxidative stress, caused damage of vascular endothelial cells, and altered the expression of adhesion factors and the activity of NOS. These changes may explain the mechanisms underlying excess iodine-induced vascular injury.

  13. THERAPY OF GRAVES’ DISEASE WITH SODIUM IODIDE-131

    Directory of Open Access Journals (Sweden)

    I Wayan Hartadi Noor

    2013-11-01

    Full Text Available Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Graves’ disease is the most common form of thyrotoxicosis, with a peak incidence in the 20-40 year of age group. Females are involved about five times more commonly than male. The easiest sign to recognize patients with Graves’ disease is the present of Graves’ ophthalmopathy. The diagnosis of Graves’ disease may sometimes base only on a physical examination and a medical history. Diffuse thyroid enlargement and sign of thyrotoxicosis, mainly ophthalmopathy and to lesser extent dermopathy, usually adequate for diagnosis. TSH test combined with FT4 test is usually the first laboratory test performs in these patients. The patients suffered Graves’ disease can be treated with antithyroid drug therapy or undergo subtotal Thyroidectomy. Another therapy is by using sodium iodide-131, where this therapy has advantages including easy administration, effectiveness, low expense, and absence of pain. /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

  14. Modeling the Detection of Organic and Inorganic Compounds Using Iodide-Based Chemical Ionization.

    Science.gov (United States)

    Iyer, Siddharth; Lopez-Hilfiker, Felipe; Lee, Ben H; Thornton, Joel A; Kurtén, Theo

    2016-02-04

    Iodide-based chemical ionization mass spectrometry (CIMS) has been used to detect and measure concentrations of several atmospherically relevant organic and inorganic compounds. The significant electronegativity of iodide and the strong acidity of hydroiodic acid makes electron transfer and proton abstraction essentially negligible, and the soft nature of the adduct formation ionization technique reduces the chances of sample fragmentation. In addition, iodide has a large negative mass defect, which, when combined with the high resolving power of a high resolution time-of-flight chemical ionization mass spectrometer (HR-ToF-CIMS), provides good selectivity. In this work, we use quantum chemical methods to calculate the binding energies, enthalpies and free energies for clusters of an iodide ion with a number of atmospherically relevant organic and inorganic compounds. Systematic configurational sampling of the free molecules and clusters was carried out at the B3LYP/6-31G* level, followed by subsequent calculations at the PBE/SDD and DLPNO-CCSD(T)/def2-QZVPP//PBE/aug-cc-pVTZ-PP levels. The binding energies, enthalpies, and free energies thus obtained were then compared to the iodide-based University of Washington HR-ToF-CIMS (UW-CIMS) instrument sensitivities for these molecules. We observed a reasonably linear relationship between the cluster binding enthalpies and logarithmic instrument sensitivities already at the PBE/SDD level, which indicates that relatively simple quantum chemical methods can predict the sensitivity of an iodide-based CIMS instrument toward most molecules. However, higher level calculations were needed to treat some outlier molecules, most notably oxalic acid and methylerythritol. Our calculations also corroborated the recent experimental findings that the molecules that the UW-CIMS detects at maximum sensitivity usually have binding enthalpies to iodide which are higher than about 26 kcal/mol, depending slightly on the level of theory.

  15. Iodide Residues in Milk Vary between Iodine-Based Teat Disinfectants.

    Science.gov (United States)

    French, Elizabeth A; Mukai, Motoko; Zurakowski, Michael; Rauch, Bradley; Gioia, Gloria; Hillebrandt, Joseph R; Henderson, Mark; Schukken, Ynte H; Hemling, Thomas C

    2016-07-01

    Majority of iodine found in dairy milk comes from the diet and teat disinfection products used during milking process. The objective of this study was to evaluate the effects of 4 iodine-based teat dips on milk iodide concentrations varying in iodine level (0.25% vs. 0.5%, w/w), normal low viscosity dip versus barrier dip, and application method (dip vs. spray) to ensure safe iodine levels in dairy milk when these products are used. The iodine exposure study was performed during a 2-wk period. The trial farm was purged of all iodine-based disinfection products for 21 d during a prestudy "washout period," which resulted in baseline milk iodide range of 145 to 182 ppb. During the experiment, iodine-based teat dips were used as post-milking teat disinfectants and compared to a non-iodine control disinfectant. Milk iodide residue levels for each treatment was evaluated from composited group samples. Introduction of different iodine-based teat disinfectants increased iodide residue content in milk relative to the control by between 8 and 29 μg/L when averaged across the full trial period. However, residues levels for any treatment remained well below the consumable limit of 500 μg/L. The 0.5% iodine disinfectant increased milk iodide levels by 20 μg/L more compared to the 0.25% iodine. Compared to dip-cup application, spray application significantly increased milk iodide residue by 21 μg/L and utilized approximately 23% more teat dip. This carefully controlled study demonstrated an increase in milk iodide concentrations from iodine disinfectants, but increases were small and within acceptable limits.

  16. [Determination of iodide, thiocyanate and perchlorate ions in environmental water by two-dimensional ion chromatography].

    Science.gov (United States)

    Lin, Li; Wang, Haibo; Shi, Yali

    2013-03-01

    A procedure for the determination of iodide, thiocyanate and perchlorate ions in environmental water by two-dimensional ion chromatography has been developed. At first the iodide, thiocyanate and perchlorate ions were separated from interfering ions by a column (IonPac AS16, 250 mm x 4 mm). The iodide ion, thiocyanate and perchlorate ions were then enriched with an enrichment column (MAC-200, 80 mm x 0.75 mm). In the 2nd-dimensional chromatography, iodide thiocyanate and perchlorate ions were separated and quantified by a capillary column (IonPac AS20 Capillary, 250 mm x 0.4 mm). The linear ranges were 0.05 -100 pg/L with correlation coefficients of 0. 999 9, and the detection limits were 0. 02 - 0.05 micro gg/L. The spiked recoveries of iodide, thiocyanate and perchlorate ions were in the range of 85.1% to 100.1%. The relative standard deviations of the recoveries were 1.7% to 4.9%.

  17. Trapping radiodine, in the form of methyl iodide, on nuclear carbon

    Energy Technology Data Exchange (ETDEWEB)

    Nacapricha, D. [Mahidol Univ., Bangkok (Thailand); Taylor, C. [John Moores Univ., Liverpool (United Kingdom)

    1996-12-31

    Studies have been performed on potassium-iodide-impregnated charcoals of the type used in the nuclear industry for trapping radioiodine released during nuclear fission. The effects of various parameters on the trapping efficiency of methyl iodide have been investigated. A variation in particle size within a bulk charcoal caused poor precision in K value measurements because of differences in surface area, pore volume, and bed density, leading to differences in the deposition of the impregnant. Precision is improved by sieving the charcoal to a narrower size because smaller particles have a higher porosity. This finding is supported by surface area and pore measurements. Two methods of impregnation are compared by measuring K values and the deposition of potassium iodide. Charcoal impregnated by rotary evaporation exhibits both higher K values and higher potassium iodide contents than sprayed charcoal. Two designs of spraying drum are compared: a drum with helical vanes allows more efficient deposition and more uniform distribution of impregnant than a drum with axial vanes. A decrease in the K value with increasing humidity correlates with the available surface area. A similar correlation exists between water content and available pore volume. Aging of potassium-iodide-impregnated charcoal, caused by the formation of oxygen complexes on the surface, is associated with significant falls in K value. K values of charcoals also can be restored to at least their original values by heat treatment in the absence of air. 12 refs., 6 figs., 1 tab.

  18. Estradiol decreases iodide uptake by rat thyroid follicular FRTL-5 cells

    Directory of Open Access Journals (Sweden)

    Furlanetto T.W.

    2001-01-01

    Full Text Available Estradiol has well-known indirect effects on the thyroid. A direct effect of estradiol on thyroid follicular cells, increasing cell growth and reducing the expression of the sodium-iodide symporter gene, has been recently reported. The aim of the present investigation was to study the effect of estradiol on iodide uptake by thyroid follicular cells, using FRTL-5 cells as a model. Estradiol decreased basal iodide uptake by FRTL-5 cells from control levels of 2.490 ± 0.370 to 2.085 ± 0.364 pmol I-/µg DNA at 1 ng/ml (P<0.02, to 1.970 ± 0.302 pmol I-/µg DNA at 10 ng/ml (P<0.003, and to 2.038 ± 0.389 pmol I-/µg DNA at 100 ng/ml (P<0.02. In addition, 4 ng/ml estradiol decreased iodide uptake induced by 0.02 mIU/ml thyrotropin from 8.678 ± 0.408 to 7.312 ± 0.506 pmol I-/µg DNA (P<0.02. A decrease in iodide uptake by thyroid cells caused by estradiol has not been described previously and may have a role in goiter pathogenesis.

  19. Processes of adsorption/desorption of iodides and cadmium cations onto/from Ag(111

    Directory of Open Access Journals (Sweden)

    VLADIMIR D. JOVIĆ

    2011-02-01

    Full Text Available In this work, the adsorption/desorption processes of iodides and cadmium cations in the presence of iodides onto/from Ag(111 were investigated. It was shown that both processes were complex, characterized by several peaks on the cyclic voltammograms (CVs. By PeakFit analysis of the recorded CVs and subsequent fitting of the obtained peaks by the Frumkin adsorption isotherm, the interaction parameter (f and the Gibbs energy of adsorption (DGads for each adsorbed phase were determined. In the case of iodide adsorption, four peaks were characterized by negative values of f, indicating attractive lateral interaction between the adsorbed anions, while two of them possessed value of f < –4, indicating phase transition processes. The adsorption/desorption processes of cadmium cations (underpotential deposition – UPD of cadmium in the presence of iodide anions was characterized by two main peaks, each of them being composed of two or three peaks with negative values of f. By the analysis of charge vs. potential dependences obtained either from the CVs or current transients on potentiostatic pulses, it was concluded that adsorbed iodides did not undergo desorption during the process of Cd UPD, but became replaced by Cd ad-atoms and remained adsorbed on top of a Cd layer and/or in between Cd the ad-atoms.

  20. Proton and iodine-127 nuclear magnetic resonance studies on the binding of iodide by lactoperoxidase

    Energy Technology Data Exchange (ETDEWEB)

    Sakurada, J.; Takahashi, S.; Shimizu, T.; Hatano, M.; Nakamura, S.; Hosoya, T.

    1987-10-06

    Interaction of an iodide ion with lactoperoxidase was studied by the use of /sup 1/H NMR, /sup 127/I NMR, and optical difference spectrum techniques. /sup 1/H NMR spectra demonstrated that a major broad hyperfine-shifted signal at about 60 ppm, which is ascribed to the heme peripheral methyl protons, was shifted toward high field by adding KI, indicating the binding of iodide to the active site of the enzyme; the dissociation constant was estimated to be 38 mM at pH 6.1. The binding was further detected by /sup 127/I NMR, showing no competition with cyanide. Both /sup 1/H NMR and /sup 127/I NMR revealed that the binding of iodide to the enzyme is facilitated by the protonation of an ionizable group with a pK/sup a/ value of 6.0-6.8, which is presumably the distal histidyl residue. Optical difference spectra showed that the binding of an aromatic donor molecule to the enzyme is slightly but distinctly affected by adding KI. On the basis of these results, it was suggested that an iodide ion binds to lactoperoxidase outside the heme crevice but at the position close enough to interact with the distal histidyl residue which possibly mediates electron transport in the iodide oxidation reaction.

  1. Californium Recovery from Palladium Wire

    Energy Technology Data Exchange (ETDEWEB)

    Burns, Jon D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-08-01

    The recovery of 252Cf from palladium-252Cf cermet wires was investigated to determine the feasibility of implementing it into the cermet wire production operation at Oak Ridge National Laboratory’s Radiochemical Engineering Development Center. The dissolution of Pd wire in 8 M HNO3 and trace amounts of HCl was studied at both ambient and elevated temperatures. These studies showed that it took days to dissolve the wire at ambient temperature and only 2 hours at 60°C. Adjusting the ratio of the volume of solvent to the mass of the wire segment showed little change in the kinetics of dissolution, which ranged from 0.176 mL/mg down to 0.019 mL/mg. A successful chromatographic separation of 153Gd, a surrogate for 252Cf, from Pd was demonstrated using AG 50x8 cation exchange resin with a bed volume of 0.5 mL and an internal diameter of 0.8 cm.

  2. Quantification of propidium iodide delivery with millisecond electric pulses: A model study

    CERN Document Server

    Yu, Miao

    2014-01-01

    A model study of propidium iodide delivery with millisecond electric pulses is presented; this work is a companion of the experimental efforts by Sadik et al. [1]. Both membrane permeabilization and delivery are examined with respect to six extra-cellular conductivities. The transmembrane potential of the permeabilized regions exhibits a consistent value, which corresponds to a bifurcation point in the pore-radius-potential relation. Both the pore area density and membrane conductance increase with an increasing extra-cellular conductivity. On the other hand, the inverse correlation between propidium iodide delivery and extra-cellular conductivity as observed in the experiments is quantitatively captured by the model. This agreement confirms that this behavior is primarily mediated by electrophoretic transport during the pulse. The results suggest that electrophoresis is important even for the delivery of small molecules such as propidium iodide. The direct comparison between model prediction and experimental...

  3. Salty glycerol versus salty water surface organization: bromide and iodide surface propensities.

    Science.gov (United States)

    Huang, Zishuai; Hua, Wei; Verreault, Dominique; Allen, Heather C

    2013-07-25

    Salty NaBr and NaI glycerol solution interfaces are examined in the OH stretching region using broadband vibrational sum frequency generation (VSFG) spectroscopy. Raman and infrared (IR) spectroscopy are used to further understand the VSFG spectroscopic signature. The VSFG spectra of salty glycerol solutions reveal that bromide and iodide anions perturb the interfacial glycerol organization in a manner similar as that found in aqueous halide salt solutions, thus confirming the presence of bromide and iodide anions at the glycerol surface. Surface tension measurements are consistent with the surface propensity suggested by the VSFG data and also show that the surface excess increases with increasing salt concentration, similar to that of water. In addition, iodide is shown to have more surface prevalence than bromide, as has also been determined from aqueous solutions. These results suggest that glycerol behaves similarly to water with respect to surface activity and solvation of halide anions at its air/liquid interface.

  4. Preparation, Characterization and Optical Properties of Host-guest Nanocomposite Material Mordenite-silver Iodide

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Silver iodide nanoclusters were successfully prepared in the channels of mordenite by a heat diffusion method. Powder X-ray diffraction, adsorption technique and infrared spectroscopy were used to characterize the prepared materials, which showed that the guest silver iodide had been encapsulated in the channels of mordenite. The optical properties of the solid phase diffuse reflectance absorption of nanocomposite material NaM-AgI were studied, showing that the absorption bands of the diffuse reflectance absorption of the prepared material moved to the region of high energy. The absorption peak of the material prepared shifted to the region of high energy. Namely, blue shift was caused. This has demonstrated the incorporation of silver iodide into the channels of the zeolite. We observed the luminescence and surface photovoltage spectra of NaM-AgI sample, proposing the mechanisms of the photoluminescence and photovoltaic responses.

  5. New Microporous Polymer Electrolyte Based on Polysiloxane Grafted with Imidazolium Iodide Moieties for DSSC

    Directory of Open Access Journals (Sweden)

    Yan Yang

    2011-01-01

    Full Text Available Two types of polysiloxane grafted with different ratio of imidazolium iodide moieties (IL-SiO2 have been synthesized to develop a micro-porous polymer electrolyte for quasi-solid-state dye-sensitized solar cells. The samples were characterized by 1HNMR, FT-IR spectrum, XRD, TEM and SEM, respectively. Moreover, the ionic conductivity of the electrolytes was measured by electrochemical workstation. Nanostructured polysiloxane containing imidazolium iodide showed excellent compatibility with organic solvent and polymer matrix for its ionic liquid characteristics. Increasing the proportion of imidazolium iodide moieties in polysiloxane improved the electrochemical behavior of the gel polymer electrolyte. A dye-sensitized solar cell with gel polymer electrolyte yielded an open-circuit voltage of 0.70 V, short-circuit current of 11.19 mA cm−2, and the conversion efficiency of 3.61% at 1 sun illumination.

  6. Optimization of mercuric iodide platelets growth by the polymer controlled vapor transport method

    Directory of Open Access Journals (Sweden)

    Fornaro L.

    1999-01-01

    Full Text Available Mercuric iodide crystals in their platelet habit were grown by the polymer controlled vapor transport method. Mercuric iodide 99% in purity was sublimated at temperatures about 122 - 126 °C and vacuum conditions (10-5 mmHg, after selecting an appropriate polymer. Temperature profiles and experimental heat transfer models were determined for two growth furnaces using different insulator configurations for the cold extreme (air, ceramic wool, grilon, copper and ceramic wool. Growth conditions for few and separate nucleation points and large crystals were determined. Representative samples were characterized by optical microscopy and by measuring the current density and apparent resistivity of the material. Future optimization and comparisons with others mercuric iodide crystal growth methods are included.

  7. Effect of Cytokine on the Expression of Sodium Iodide Symporter Gene in Breast Cancer Cell

    Institute of Scientific and Technical Information of China (English)

    JIAYue; LIUChao; TANGWei; LIUCui-ping; QINYou-wen; YUANQing-xing; LIQian; MAOXiao-dong; DIFu-song

    2004-01-01

    To investigate the effect of cytokines (TNF-α, IFN-γ and IL-6) on the expression of sodi-um-iodide symporter(NIS) gene in breast cancer cell (MCF-7). Methods:The breast cancer cell was cultureds with negative control culture or cultures with different concentrations of cytokines for 72 h. NIS germ mRNA in breast cancer cells cultured was determined by reverse transcriptase-polymerase chain reaction(RT-PCR). Results:Expression of sodium-iodide symporter mRNA can be found decreasing along with increasing the concentration of cytokine dose-depen-dently. Conchzs/on ~ Cytokine may play a role in iodide-uptake modulating in breast cancer cells by their effect on NIS germ expression.

  8. All-Solid-State Iodide Selective Electrode for Iodimetry of Iodized Salts and Vitamin C

    Directory of Open Access Journals (Sweden)

    TIRUWORK MEQUANINT

    2012-12-01

    Full Text Available A laboratory-made all-solid state iodide selective electrode, with Ag2S-AgI coated on a graphite rod recovered from dry cell battery, was prepared according to previous procedures. The electrode’s linear response to iodide was in the concentration range of 10-6 M to 10-1 M with a slope of 56.85 mV/decade and a detection limit of 6×10-7M. Iodate recovery test for laboratory formulated iodate-iodized salt was found to be 98.6 % with a standard deviation of 1.14%. The titratability of the iodized salt solution was at least 10-200 ppm potassium iodate (6-120 ppm iodine, exhibiting distinct endpoints in the range wider than the ones set in regulatory standards and reflecting that QC monitoring in production and stability decline of iodine content upon storage can be performed with the electrode method. On the basis this potentiometric titration, the application of the laboratory-made iodide electrode (vs. a saturated calomel reference electrode was extended to the determination of iodine in commercial iodized salts. In all the iodine assays, the iodate-iodized salt was initially treated with acid and an excess of iodide before titration against Na2S2O3 solution. The iodine content in table salts iodized with iodide was determined by direct potentiometry. The electrode was further used for vitamin C (ascorbic acid determinations in pharmaceutical tablets and orange juice by back titrating excess I3- against standard Na2S2O3 in acidic media. The overall outcome is that the iodide ISE can be used as sharp endpoint indicator for these titrimetric reactions in place of the well known official, but visually monitored, starch- triodide end-point reaction detection.

  9. Iodide uptake in human anaplastic thyroid carcinoma cells after transfer of the human thyroid peroxidase gene

    Energy Technology Data Exchange (ETDEWEB)

    Haberkom, U. [Clinical Cooperation Unit Nuclear Medicine, German Cancer Research Center, Heidelberg (Germany); Dept. of Nuclear Medicine, Univ. of Heidelberg (Germany); Altmann, A.; Jiang, S.; Morr, I.; Mahmut, M. [Clinical Cooperation Unit Nuclear Medicine, German Cancer Research Center, Heidelberg (Germany); Eisenhut, M. [Dept. of Nuclear Medicine, Univ. of Heidelberg (Germany)

    2001-05-01

    Human thyroperoxidase (hTPO) is critical for the accumulation of iodide in thyroid tissues. Poorly differentiated and anaplastic thyroid tumours which lack thyroid-specific gene expression fail to accumulate iodide and, therefore, do not respond to iodine-131 therapy. We consequently investigated whether transfer of the hTPO gene is sufficient to restore the iodide-trapping capacity in undifferentiated thyroid and non-thyroid tumour cells. The human anaplastic thyroid carcinoma cell lines C643 and SW1736, the rat Morris hepatoma cell line MH3924A and the rat papillary thyroid carcinoma cell line L2 were used as in vitro model systems. Employing a bicistronic retroviral vector based on the myeloproliferative sarcoma virus for the transfer of the hTPO and the neomycin resistance gene, the C643 cells and SW1736 cells were transfected while the L2 cells and MH3924A cells were infected with retroviral particles. Seven recombinant C643 and seven SW1736 cell lines as well as four recombinant L2 and four MH3924A cell lines were established by neomycin selection. They were studied for hTPO expression using an antibody-based luminescence kit, followed by determination of the enzyme activity in the guaiacol assay and of the iodide uptake capacity in the presence of Na{sup 125}I. Genetically modified cell lines expressed up to 1,800 times more hTPO as compared to wild type tumour cells. The level of hTPO expression varied significantly between individual neomycin-resistant cell lines, suggesting that the recombinant retroviral DNA was integrated at different sites of the cellular genome. The accumulation of iodide, however, was not significantly enhanced in individual recombinant cell lines, irrespective of low or high hTPO expression. Moreover, there was no correlation between hTPO expression and enzyme activity in individual cell lines. The transduction of the hTPO gene per se is not sufficient to restore iodide trapping in non-iodide-concentrating tumour cells. Future

  10. Development of W/O Microemulsion for Transdermal Delivery of Iodide Ions

    OpenAIRE

    Lou, Hao; Qiu, Ni; Crill, Catherine; Helms, Richard; Almoazen, Hassan

    2012-01-01

    The objective of this study was to develop a water-in-oil (w/o) microemulsion which can be utilized as a transdermal delivery for iodide ions. Several w/o microemulsion formulations were prepared utilizing Span 20, ethanol, Capryol 90®, and water. The selected formulations had 5%, 10%, 15%, 20%, and a maximum of 23% w/w water content. Potassium iodide (KI) was incorporated in all formulations at 5% w/v. Physicochemical characterizations were conducted to evaluate the structure and stability. ...

  11. All-Solid-State Iodide Selective Electrode for Iodimetry of Iodized Salts and Vitamin C

    OpenAIRE

    TIRUWORK MEQUANINT; GHIRMA MOGES; MERID TESSMA; SOLOMON MEHRETU

    2012-01-01

    A laboratory-made all-solid state iodide selective electrode, with Ag2S-AgI coated on a graphite rod recovered from dry cell battery, was prepared according to previous procedures. The electrode’s linear response to iodide was in the concentration range of 10-6 M to 10-1 M with a slope of 56.85 mV/decade and a detection limit of 6×10-7M. Iodate recovery test for laboratory formulated iodate-iodized salt was found to be 98.6 % with a standard deviation of 1.14%. The titratability of the iodize...

  12. Tris(1,2-dimethoxyethane-κ2O,O′iodidocalcium iodide

    Directory of Open Access Journals (Sweden)

    Siou-Wei Ou

    2012-02-01

    Full Text Available In the title complex, [CaI(C4H10O23]I, the CaII atom is seven-coordinated by six O atoms from three 1,2-dimethoxyethane (DME ligands and one iodide anion in a distorted pentagonal–bipyramidal geometry. The I atom and one of the O atoms from a DME ligand lie in the axial positions while the other O atoms lie in the basal plane. The other iodide anion is outside the complex cation.

  13. Glycosylation of Sodium/Iodide Symporter (NIS) Regulates Its Membrane Translocation and Radioiodine Uptake

    OpenAIRE

    Taemoon Chung; Hyewon Youn; Chan Joo Yeom; Keon Wook Kang; June-Key Chung

    2015-01-01

    Purpose Human sodium/iodide symporter (hNIS) protein is a membrane glycoprotein that transports iodide ions into thyroid cells. The function of this membrane protein is closely regulated by post-translational glycosylation. In this study, we measured glycosylation-mediated changes in subcellular location of hNIS and its function of iodine uptake. Methods HeLa cells were stably transfected with hNIS/tdTomato fusion gene in order to monitor the expression of hNIS. Cellular localization of hNIS ...

  14. Studying Equilibrium in the Chemical Reaction between Ferric and Iodide Ions in Solution Using a Simple and Inexpensive Approach

    Science.gov (United States)

    Nikolaychuk, Pavel Anatolyevich; Kuvaeva, Alyona Olegovna

    2016-01-01

    A laboratory experiment on the study of the chemical equilibrium based on the reaction between ferric and iodide ions in solution with the formation of ferrous ions, free iodine, and triiodide ions is developed. The total concentration of iodide and triiodide ions in the reaction mixture during the reaction is determined by the argentometric…

  15. Efficiency enhancement in dye sensitized solar cells using gel polymer electrolytes based on a tetrahexylammonium iodide and MgI2 binary iodide system.

    Science.gov (United States)

    Bandara, T M W J; Dissanayake, M A K L; Jayasundara, W J M J S R; Albinsson, I; Mellander, B-E

    2012-06-28

    Quasi-solid-state dye-sensitized solar cells have drawn the attention of scientists and technologists as a potential candidate to supplement future energy needs. The conduction of iodide ions in quasi-solid-state polymer electrolytes and the performance of dye sensitized solar cells containing such electrolytes can be enhanced by incorporating iodides having appropriate cations. Gel-type electrolytes, based on PAN host polymers and mixture of salts tetrahexylammonium iodide (Hex4N(+)I(-)) and MgI2, were prepared by incorporating ethylene carbonate and propylene carbonate as plasticizers. The salt composition in the binary mixture was varied in order to optimize the performance of solar cells. The electrolyte containing 120% Hex4N(+)I(-) with respect to weight of PAN and without MgI2 showed the highest conductivity out of the compositions studied, 2.5 × 10(-3) S cm(-1) at 25 °C, and a glass transition at -102.4 °C. However, the electrolyte containing 100% Hex4N(+)I(-) and 20% MgI2 showed the best solar cell performance highlighting the influence of the cation on the performance of the cell. The predominantly ionic behaviour of the electrolytes was established from the dc polarization data and all the electrolytes exhibit iodide ion transport. Seven different solar cells were fabricated employing different electrolyte compositions. The best cell using the electrolyte with 100% Hex4N(+)I(-) and 20% MgI2 with respect to PAN weight showed 3.5% energy conversion efficiency and 8.6 mA cm(-2) short circuit current density.

  16. Iodide-induced thyrotoxicosis in a thyroidectomized patient with metastatic thyroid carcinoma

    Energy Technology Data Exchange (ETDEWEB)

    Yoshinari, M.; Tokuyama, T.; Okamura, K.; Sato, K.; Kusuda, K.; Fujishima, M.

    1988-04-15

    An unusual case of iodide-induced thyrotoxicosis is documented in this article. The patient was a 64-year-old euthyroid man with acromegaly. He also had multiple follicular and papillary thyroid carcinomas with a metastatic lesion in the lumbar vertebrae. After a total thyroidectomy, he became slightly hypothyroid, and the lumbar lesion began to incorporate /sup 131/I by scintigraphy. When an iodine-containing contrast medium happened to be injected, a transient increase of serum thyroid hormone level was observed. After complete thyroid ablation with 83 mCi of /sup 131/I, the oral administration of 100 mg of potassium iodide for 7 days induced a prominent increase of serum thyroid hormone level. These findings indicated that the metastatic thyroid carcinoma could produce excess thyroid hormone insofar as a sufficient amount of iodide was given. Although this is the first report of such a case, iodide-induced thyrotoxicosis may not be rare in patients with thyroid carcinomas because the Wolff-Chaikoff effect is thought to be lost, and the organic iodinating activity and lysosomal protease activity are well-preserved.

  17. Leaching of iodide (I(-)) and iodate (IO3(-)) anions from synthetic layered double hydroxide materials.

    Science.gov (United States)

    Theiss, Frederick L; Ayoko, Godwin A; Frost, Ray L

    2016-09-15

    Several studies have previously demonstrated that layered double hydroxides (LDHs) show considerable potential for the adsorption of radioiodine from aqueous solution; however, few studies have demonstrated that these materials are able to store radioactive (131)I for an acceptable period. The leaching of iodide (I(-)) and iodate (IO3(-)) form Mg/Al LDHs has been carried out. Contact time appeared to be a more significant variable for the leaching of iodate (IO3(-)) compared to that of iodide (I(-)). Experimental results are fitted to the pseudo second order model, suggesting that diffusion is likely to be the rate-limiting step. The presence of carbonate in the leaching solution appeared to significantly increase the leaching of iodide (I(-)) as did the presence of chloride to a lesser extent. The maximum amount of iodate (IO3(-)) leached using ultrapure water as the leaching solution was 21% of the iodate (IO3(-)) originally present. The corresponding result for iodide (I(-)) was even lower at 3%.

  18. Photodissociation of sodium iodide and resonant ionization of sodium atom produced

    Institute of Scientific and Technical Information of China (English)

    HUO Bing-hai; Z.T.Salim; A.H.Bakery

    2004-01-01

    Resonant ionization spectroscopy (RIS) and resonant ionization mass spectroscopy (RIMS) are employed to detect the photodissociation product of sodium iodide molecules in a molecular beam in an intense laser field in the absence of the buffer gases. Time of flight mass spectra is recorded. In particular, the appearances of multiphoton ionization are discussed.

  19. Preparation and Luminescence Thermochromism of Tetranuclear Copper(I)-Pyridine-Iodide Clusters

    Science.gov (United States)

    Parmeggiani, Fabio; Sacchetti, Alessandro

    2012-01-01

    A simple and straightforward synthesis of a tetranuclear copper(I)-pyridine-iodide cluster is described as a laboratory experiment for advanced inorganic chemistry undergraduate students. The product is used to demonstrate the fascinating and visually impressive phenomenon of luminescence thermochromism: exposed to long-wave UV light, the…

  20. The sodium iodide symporter (NIS) and potential regulators in normal, benign and malignant human breast tissue.

    LENUS (Irish Health Repository)

    Ryan, James

    2011-01-01

    The presence, relevance and regulation of the Sodium Iodide Symporter (NIS) in human mammary tissue remains poorly understood. This study aimed to quantify relative expression of NIS and putative regulators in human breast tissue, with relationships observed further investigated in vitro.

  1. Research data supporting "Photon recycling in lead-iodide perovskite solar cells"

    OpenAIRE

    Pazos-Outón, Luis M.; Szumilo, Monika; Lamboll, Robin; Richter, Johannes M.; Crespo-Quesada, Micaela; Abdi - Jalebi, Mojtaba; Beeson, Harry J.; Vrucinic, Milan; Alsari, Mejd; Snaith, Henry J.; Ehrler, Bruno; Friend, Richard H.; Deschler, Felix

    2016-01-01

    Data for the figures presented in the manuscript. These research data support “Photon recycling in lead-iodide perovskite solar cells” published in “Science” (http://dx.doi.org./10.1126/science.aaf1168) This work was supported by the EPSRC [grant number EP/M005143/1] and Winton Programme for the Physics of Sustainability.

  2. Real-Time Observation of Organic Cation Reorientation in Methylammonium Lead Iodide Perovskites

    NARCIS (Netherlands)

    Bakulin, Artem A.; Selig, Oleg; Bakker, Huib J.; Rezus, Yves L. A.; Mueller, Christian; Glaser, Tobias; Lovrincic, Robert; Sun, Zhenhua; Chen, Zhuoying; Walsh, Aron; Frost, Jarvist M.; Jansen, Thomas L. C.

    2015-01-01

    The introduction of a mobile and polarized organic moiety as a cation in 3D lead-iodide perovskites brings fascinating optoelectronic properties to these materials. The extent and the time scales of the orientational mobility of the organic cation and the molecular mechanism behind its motion remain

  3. Multiple subcutaneous mycetomas caused by Pseudallescheria boydii: response to therapy with oral potassium iodide solution.

    Science.gov (United States)

    Khan, Fida A; Hashmi, Shahrukh; Sarwari, Arif R

    2010-02-01

    We describe the case of a sixteen-year-old male who presented with multiple subcutaneous mycetomas proven on culture to be secondary to Pseudallescheria boydi., The lesions responded completely to oral potassium iodide solution. To our knowledge this has never been reported in humans.

  4. Regioselective iodination of aromatic compounds with potassium iodide in the presence of benzyltriphenylphosphonium perchlorate

    Institute of Scientific and Technical Information of China (English)

    Jalal Albadi; Masoumeh Abedini; Nasir Iravani

    2012-01-01

    A simple and efficient method for the selective iodination of various aromatic compounds by using potassium iodide in the presence of benzyltriphenylphosphonium perchlorate,is reported.This method provides several advantages such as good selectivity between ortho and para positions of aromatic compounds and high yields of the products.

  5. The Reaction between Iron(II) Iodide and Potassium Dichromate(VI) in Acidified Aqueous Solution

    Science.gov (United States)

    Talbot, Christopher

    2013-01-01

    This "Science note" teaching lesson explores the possible reaction between the ions in a reaction mixture consisting of iron(II) iodide and potassium dichromate(VI) in acidified aqueous solution. The electrode potentials will be used to deduce any spontaneous reactions under standard thermodynamic conditions (298 K, 1 bar (approximately…

  6. Relaxation of the Silver/Silver Iodide Electrode in Aqueous Solution

    NARCIS (Netherlands)

    Peverelli, K.J.

    1979-01-01

    The aim of this study is to detect and characterize relaxation processes on silver/silver iodide electrodes in aqueous electrolyte solution. The information obtained is to be used for an estimation of the consequences of similar processes on colloidal AgI particles during encounter.In chapter 1 a ge

  7. Activation of lactoperoxidase by heme-linked protonation and heme-independent iodide binding.

    Science.gov (United States)

    Toyama, Akira; Tominaga, Aya; Inoue, Tatsuo; Takeuchi, Hideo

    2010-01-01

    Lactoperoxidase (LPO), a mammalian secretory heme peroxidase, catalyzes the oxidation of thiocyanate by hydrogen peroxide to produce hypothiocyanate, an antibacterial agent. Although LPO is known to be activated at acidic pH and in the presence of iodide, the structural basis of the activation is not well understood. We have examined the effects of pH and iodide concentration on the catalytic activity and the structure of LPO. Electrochemical and colorimetric assays have shown that the catalytic activity is maximized at pH 4.5. The heme Soret absorption band exhibits a small red-shift at pH 5.0 upon acidification, which is ascribable to a structural transition from a neutral to an acidic form. Resonance Raman spectra suggest that the heme porphyrin core is slightly contracted and the Fe-His bond is strengthened in the acidic form compared to the neutral form. The structural change of LPO upon activation at acidic pH is similar to that observed for myeloperoxidase, another mammalian heme peroxidase, upon activation at neutral pH. Binding of iodide enhances the catalytic activity of LPO without affecting either the optimum pH of activity or the heme structure, implying that the iodide binding occurs at a protein site away from the heme-linked protonation site.

  8. Distribution of bromine in mixed iodide-bromide organolead perovskites and its impact on photovoltaic performance

    NARCIS (Netherlands)

    Zhou, Yang; Wang, Feng; Fang, Hong-Hua; Loi, Maria Antonietta; Xie, Fang-Yan; Zhao, Ni; Wong, Ching-Ping

    2016-01-01

    Mixed iodide-bromide (I-Br) organolead perovskites are of great interest for both single junction and tandem solar cells since the optical bandgap of the materials can be tuned by varying the bromine to iodine ratio. Yet, it remains unclear how bromine incorporation modifies the properties of the pe

  9. Photoexcitation dynamics in solution-processed formamidinium lead iodide perovskite thin films for solar cell applications

    NARCIS (Netherlands)

    Fang, Hong-Hua; Wang, Feng; Adjokatse, Sampson; Zhao, Ni; Even, Jacky; Loi, Maria Antonietta

    2016-01-01

    Formamidinium lead iodide (FAPbI(3)) is a newly developed hybrid perovskite that potentially can be used in high-efficiency solution-processed solar cells. Here, the temperature-dependent dynamic optical properties of three types of FAPbI(3) perovskite films (fabricated using three different precurs

  10. Experimental study on iodine chemistry (EXSI) - Containment experiments with methyl iodide

    Energy Technology Data Exchange (ETDEWEB)

    Holm, J.; Ekberg, C. (Chalmers Univ. of Technology, Goeteborg (Sweden)); Kaerkelae, T.; Auvinen, A. (VTT, Espoo (Finland)); Glaenneskog, H. (Vattenfall Power Consultant, Goeteborg (Sweden))

    2011-05-15

    An experimental study on radiolytic decomposition of methyl iodide was conducted in co-operation between VTT and Chalmers University of Technology as a part of the NKS-R programs. In year 2008 the NROI project, a Nordic collaboration studying iodine chemistry in the containment, was started. During year 2008 (NROI-1) the radiolytic oxidation of elemental iodine was investigated and during 2009 (NROI-2), the radiolytic oxidation of organic iodine was studied. This project (NROI-3) is a continuation of the investigation of the oxidation of organic iodine. The project has been divided into two parts. 1. The aims of the first part were to investigate the effect of ozone and UV-radiation, in dry and humid conditions, on methyl iodide. 2. The second project was about gamma radiation (approx20 kGy/h) and methyl iodide in dry and humid conditions. 1. Experimental results showed that the methyl iodide concentration in the facility was reduced with increasing temperature and increasing UV-radiation intensity. Similar behaviour occurred when ozone was present in the system. Formed organic gas species during the decomposition of methyl iodide was mainly formaldehyde and methanol. The particle formation was instant and extensive when methyl iodide was exposed to ozone and/or radiation at all temperatures. The size of the formed primary particles was about 10 nm and the size of secondary particles was between 50-200 nm. From the SEM-EDX analyses of the particles, the conclusion was drawn that these were some kind of iodine oxides (I{sub xO{sub y}). However, the correct speciation of the formed particles was difficult to obtain because the particles melted and fused together under the electron beam. 2. The results from this sub-project are more inconsistent and hard to interpret. The particle formation was significant lesser than corresponding experiments when ozone/UV-radiation was used instead of gamma radiation. The transport of gaseous methyl iodide through the facility was

  11. Conversion of Iodide to Hypoiodous Acid and Molecular Iodine at the Air-Water Interface

    Science.gov (United States)

    Pillar, E. A.; Guzman, M. I.

    2013-12-01

    Sea spray aerosols continuously transfer a significant amount of halides to the marine boundary layer, where they play a major role in the depletion of tropospheric ozone. The reactivity of iodide is of special interest in sea spray aerosols, where this species is enriched relative to chloride and bromide in surface seawater. This work presents laboratory experiments that provide mechanistic information to understand the reactivity of halides in atmospheric aerosols. Pneumatically assisted electrospray is used to aerosolize solutions of sodium iodide (0.01-100 μM), which are rapidly (~3 μs) oxidized by ozone at 25 °C. Reaction products include HIO, IO2-, IO3-, I2, HI2O-, and I3-, all identified by mass spectrometry. The distribution of products varies along two different reaction pathways, one favoring the production of I2 and HIO for typical tropospheric ozone levels (~50 ppbv), and another one directed to the production of IO3- at higher oxidizer concentrations. The formation of products increases exponentially with rising concentrations of initial sodium iodide, [NaI]0. The process is determined to be pH independent for the pH range 6-8 representative of surface waters. The substitution of aqueous solutions by organic solvents, such as methanol or acetonitrile, causes a decrease in the surface tension and lifetime of the droplets, leading to larger I2 production. The presence of surface active organic compounds, which alter the structure of the interfacial region, promote the pathway of I2 formation over IO3-. In conclusion, this presentation will show how the oxidation of iodide in aqueous microdroplets can release reactive gas-phase species, such as I2 and HIO, capable to affect tropospheric ozone globally. Normalized intensity of products observed during the ozonolysis of iodide solutions at 130 ppbv ozone. Cone voltage = 70 V, needle voltage = 2.5 kV.

  12. [The application of eosin and propidium iodide in evaluation of vitality of human spermatozoa].

    Science.gov (United States)

    Ploskonos, М В

    2014-11-01

    The article analyzes comparative assessment of vitality of spermatozoa by condition of permeability of membranes for eosin and propidium iodide and comparison of results acquired using technique of light and fluorescent microscopy. The comparison of data of light microscopy with eosin staining with data of fluorescent microscopy with propidium iodide staining demonstrated that percentage of content of spermatozoa separated from ejaculates of 28 fertile males and stained with eosin was reliably higher (34.8 ± 3.2) than percentage of content of spermatozoa with stained with propidium iodide (2.1 ± 4.0). After incubation of spermatozoa under room temperature during 24 hours percentage of unviable cells with stained eosin also was higher than in case of propidium iodide staining correspondingly (44.5 ± 3.3% and 34.7 ± 3.6%). The analysis of vitality of spermatozoa under damaging effect of oxidative stress on cell membrane developed by 4 hours incubation with 200 mkM of hydrogen peroxide (H2O2) demonstrated that under staining of spermatozoa with propidium iodide significantly higher percentage of damaged cells is detected. In such cases, eosin staining is less suitable for detection of vitality of spermatozoa (73.6 ± 5.8% against 51.7 ± 6.4%). The carried out experiment demonstrates that in case of detected effects on spermatozoa (for example, effect of oxidative stress) the light microscopy insufficiently adequate reflects degree of damage of membranes of spermatozoa. The fluorescent microscopy detects a higher percentage of spermatozoa with damaged membrane.

  13. 碘化物对金精矿碘化浸出过程的影响%Effects of different iodides on gold concentrates leaching process in iodine­iodide solution

    Institute of Scientific and Technical Information of China (English)

    李绍英; 王海霞; 孙春宝; 赵留成; 阎志强

    2013-01-01

    Using the iodine­iodide leaching system, the effects of different iodides (ammonium iodide,potassium iodide, hydrogen iodide)on gold concentrates leaching process were discussed from the influence factors, such as initial iodine content, iodine and iodide ratio and solution pH value. The results show that, when ammonium iodide or potassium iodide is used as complex agent,under the conditions of initial iodine content of 1%, iodine and iodide molar ratio of 1:8, pH value of 7, liquid­solid ratio of 4:1, stirring speed of 600 r/min, leaching time of 4 h and temperature of 25℃, the gold leaching rates are around 90%;whereas the gold leaching effect is poorer when hydrogen iodide(aqueous solution is hydroiodic acid) is used as complex agent, and the gold leaching rate is only 75%. Considering the difference of leaching effect and availability of industry and so on,potassium iodide is the suitable complex reagent of gold concentrate leaching in iodine­iodide solution.%  采用碘−碘化物浸出体系,从碘初始含量、碘与碘化物摩尔比和浸出液pH值3个影响因素入手,考察不同碘化物(碘化铵、碘化钾和碘化氢)对金精矿碘化浸出过程的影响。结果表明:在碘初始含量为1%,碘与碘化物摩尔比为1:8,浸出液pH值为7,液固比为4:1,搅拌速度为600 r/min,浸出时间为4 h,温度为25℃的条件下,用碘化铵或碘化钾作为碘化浸金的络合剂,金的浸出率均能达到90%左右,而用碘化氢(其水溶液为氢碘酸)作络合剂时,金的浸出率仅有75%。考虑到不同碘化物浸金效果差异及工业应用的可行性等因素,确定碘化钾为适宜的金精矿碘化浸出络合剂。

  14. Radioactive iodide (131 I-) excretion profiles in response to potassium iodide (KI) and ammonium perchlorate (NH4ClO4) prophylaxis.

    Science.gov (United States)

    Harris, Curtis; Dallas, Cham; Rollor, Edward; White, Catherine; Blount, Benjamin; Valentin-Blasini, Liza; Fisher, Jeffrey

    2012-08-01

    Radioactive iodide ((131)I-) protection studies have focused primarily on the thyroid gland and disturbances in the hypothalamic-pituitary-thyroid axis. The objective of the current study was to establish (131)I- urinary excretion profiles for saline, and the thyroid protectants, potassium iodide (KI) and ammonium perchlorate over a 75 hour time-course. Rats were administered (131)I- and 3 hours later dosed with either saline, 30 mg/kg of NH(4)ClO(4) or 30 mg/kg of KI. Urinalysis of the first 36 hours of the time-course revealed that NH(4)ClO(4) treated animals excreted significantly more (131)I- compared with KI and saline treatments. A second study followed the same protocol, but thyroxine (T(4)) was administered daily over a 3 day period. During the first 6-12 hour after (131)I- dosing, rats administered NH(4)ClO(4) excreted significantly more (131)I- than the other treatment groups. T(4) treatment resulted in increased retention of radioiodide in the thyroid gland 75 hour after (131)I- administration. We speculate that the T(4) treatment related reduction in serum TSH caused a decrease synthesis and secretion of thyroid hormones resulting in greater residual radioiodide in the thyroid gland. Our findings suggest that ammonium perchlorate treatment accelerates the elimination rate of radioiodide within the first 24 to 36 hours and thus may be more effective at reducing harmful exposure to (131)I- compared to KI treatment for repeated dosing situations. Repeated dosing studies are needed to compare the effectiveness of these treatments to reduce the radioactive iodide burden of the thyroid gland.

  15. Experimental study on iodine chemistry (EXSI) - Containment experiments with methyl iodide

    Energy Technology Data Exchange (ETDEWEB)

    Holm, J.; Glaenneskog, H.; Ekberg, C. (Chalmers Univ. of Technology (Sweden)); Kaerkelae, T.; Auvinen, A. (VTT Technical Research Centre of Finland (Finland))

    2010-05-15

    An experimental study on radiolytic decomposition of methyl iodide was conducted in co-operation between VTT and Chalmers University of Technology as a part of the NKS-R programs. The behaviour of iodine during a severe accident has been studied in several experimental programs, ranging from the large-scale PHEBUS FP tests and intermediate-scale ThAI tests to numerous separate effect studies. In year 2008 the NROI project, a Nordic collaboration studying iodine chemistry in the containment was started. During 2009, oxidation of iodine, especially organic iodine, was studied within the NROI project. The chemistry of organic iodine in the gas phase is still one of the greatest remaining uncertainties concerning iodine behaviour during a severe accident. During the first year of the NROI project the oxidation of elemental iodine, I2, with ozone and UV-light was investigated. In this study organic iodide, in this case methyl iodide, was investigated in similar conditions as in the NROI-1 project. The experimental facility applied in this study is based on the sampling system built at VTT for the ISTP project CHIP conducted by IRSN. The experimental facility and the measuring technology are sophisticated and unique in the area of nuclear research as well as in the field of aerosol science. Experimental results showed that the methyl iodide concentration in the facility was reduced with increasing temperature and increasing UVC intensity. Similar behaviour occurred when ozone was present in the system. Formed organic gas species during the decomposition of methyl iodide was mainly formaldehyde and methanol. Instant and extensive particle formation occurred when methyl iodide was transported through a UVC radiation field and/or when ozone was present. The size of the formed primary particles was about 10 nm and the size of secondary particles was between 50-150 nm. From the SEM-EDX analyses of the particles, the conclusion was drawn that these were some kind of iodine

  16. Design of a homogeneous subcritical nuclear reactor based on thorium with a source of californium 252; Diseno de un reactor nuclear subcritico homogeneo a base de Torio con una fuente de Californio 252

    Energy Technology Data Exchange (ETDEWEB)

    Delgado H, C. E.; Vega C, H. R. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico); Sajo B, L., E-mail: ce_delgado89@hotmail.com [Universidad Simon Bolivar, Laboratorio de Fisica Nuclear, Apdo. 89000, 1080A Caracas (Venezuela, Bolivarian Republic of)

    2015-10-15

    Full text: One of the energy alternatives to fossil fuels which do not produce greenhouse gases is the nuclear energy. One of the drawbacks of this alternative is the generation of radioactive wastes of long half-life and its relation to the generation of nuclear materials to produce weapons of mass destruction. An option to these drawbacks of nuclear energy is to use Thorium as part of the nuclear fuel which it becomes in U{sup 233} when capturing neutrons, that is a fissile material. In this paper Monte Carlo methods were used to design a homogeneous subcritical reactor based on thorium. As neutron reflector graphite was used. The reactor core is homogeneous and is formed of 70% light water as moderator, 12% of enriched uranium UO{sub 2}(NO{sub 3}){sub 4} and 18% of thorium Th(NO{sub 3}){sub 4} as fuel. To start the nuclear fission chain reaction an isotopic source of californium 252 was used with an intensity of 4.6 x 10{sup 7} s{sup -1}. In the design the value of the effective multiplication factor, whose value turned out k{sub eff} <1 was calculated. Also, the neutron spectra at different distances from the source and the total fluence were calculated, as well as the values of the ambient dose equivalent in the periphery of the reactor. (Author)

  17. Manganese determination om minerals by activation analysis, using the californium-252 as a neutron source; Determinacao de manganes em minerios, por analise por ativacao, usando californio-252 como fonte de neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Cardoso, Antonio

    1976-07-01

    Neutron Activation Analysis, using a Californium-252 neutron source, has been applied for the determination of manganese in ores such as pyrolusite, rodonite (manganese silicate)' and blending used in dry-batteries The favorable nuclear properties of manganese, such as high thermal neutron cross-section for the reaction {sup 55}Mn (n.gamma){sup 56} Mn, high concentration of manganese in the matrix and short half - life of {sup 56}Mn, are an ideal combination for non-destructive analysis of manganese in ores. Samples and standards of manganese dioxide were irradiated for about 20 minutes, followed by a 4 to 15 minutes decay and counted in a single channel pulse-height discrimination using a NaI(Tl) scintillation detector. Counting time was equal to 10 minutes. The interference of nuclear reactions {sup 56}Fe(n,p){sup 56}Mn and {sup 59} Co (n, {alpha}){sup 56} were studied, as well as problems in connection with neutron shadowing during irradiation, gamma-rays attenuation during counting and influence of granulometry of samples. One sample,was also analysed by wet-chemical method (sodium bismuthate) in order to compare results. As a whole, i t was shown that the analytical method of neutron activation for manganese in ores and blending, is a method simple, rapid and with good precision and accuracy. (author)

  18. Cooperative effect of silver in copper-catalyzed trifluoromethylation of aryl iodides using Me3SiCF3

    KAUST Repository

    Weng, Zhiqiang

    2011-06-13

    An effective model of cooperative effect of silver for the coppercatalyzed trifluoromethylation of activated and unactivated aryl iodides to trifluoromethylated arenes using Me3SiCF3 was achieved with a broad substrate scope. © 2011 American Chemical Society.

  19. Formation of iodinated disinfection by-products during oxidation of iodide-containing water with potassium permanganate.

    Science.gov (United States)

    Ye, Tao; Xu, Bin; Lin, Yi-Li; Hu, Chen-Yan; Xia, Sheng-Ji; Lin, Lin; Mwakagenda, Seleli Andrew; Gao, Nai-Yun

    2012-11-30

    This study shows that iodinated disinfection by-products (I-DBPs) including iodoform (IF), iodoacetic acid (IAA) and triiodoacetic acid (TIAA) can be produced when iodide-containing waters are in contact with potassium permanganate. IF was found as the major I-DBP species during the oxidation. Iodide was oxidized to HOI, I(2) and I(3)(-), consequently, which led to the formation of iodinated organic compounds. I-DBPs varied with reaction time, solution pH, initial concentrations of iodide and potassium permanganate. Yields of IF, IAA and TIAA increased with reaction time and considerable I-DBPs were formed within 12 h. Peak IF yields were found at circumneutral pH range. However, formation of IAA and TIAA was favored under acidic conditions. Molar ratio of iodide to potassium permanganate showed significant influence on formation of IF, IAA and TIAA. The formation of IF, IAA and TIAA also depended on the characteristics of the waters.

  20. Gap energy studied by optical transmittance in lead iodide monocrystals grown by Bridgman's Method

    Directory of Open Access Journals (Sweden)

    Veissid N.

    1999-01-01

    Full Text Available The bandgap energy as a function of temperature has been determined for lead iodide. The monocrystal was obtained in a vacuum sealed quartz ampoule inside a vertical furnace by Bridgman's method. The optical transmittance measurement enables to evaluate the values of Eg. By a fitting procedure of Eg as a function of temperature is possible to extract the parameters that govern its behavior. The variation of Eg with temperature was determined as: Eg(T = Eg(0 - aT2/(a + T, with: Eg(0 = (2.435 ± 0.008 eV, a = (8.7 ± 1.3 x 10-4 eV/K and a = (192 ± 90 K. The bandgap energy of lead iodide at room temperature was found to be 2.277 ± 0.007 eV.

  1. Induction of iodide uptake in transformed thyrocytes: a compound screening in cell lines

    Energy Technology Data Exchange (ETDEWEB)

    Froehlich, Eleonore [University of Tuebingen, Department of Endocrinology, Metabolism, Nephrology and Clinical Chemistry, Internal Medicine, Tuebingen (Germany); Brossart, Peter [University of Tuebingen, Department of Haematology, Oncology, Immunology and Rheumatology, Internal Medicine, Tuebingen (Germany); Wahl, Richard [University of Tuebingen, Department of Endocrinology, Metabolism, Nephrology and Clinical Chemistry, Internal Medicine, Tuebingen (Germany); Department IV, Internal Medicine, Tuebingen (Germany)

    2009-05-15

    Retinoic acid presently is the most advanced agent able to improve the efficacy of radioiodine therapy in differentiated thyroid carcinoma. In order to identify compounds with higher efficacy a panel of pharmacologically well-characterized compounds with antitumour action in solid cancer cell lines was screened. The effects of the compounds on iodide uptake, cell number, proliferation and apoptosis were evaluated. In general, compounds were more effective in cell lines derived from more aggressive tumours. The effectiveness in terms of number of responsive cell lines and maximal increase in iodide uptake achieved decreased in the order: APHA > valproic acid {approx} sirolimus {approx} arsenic trioxide > retinoic acid {approx} lovastatin > apicidine {approx} azacytidine {approx} retinol {approx} rosiglitazone {approx} bortezomib. We hypothesize that testing of cells from primary tumours or metastases in patients may be a way to identify compounds with optimum therapeutic efficacy for individualized treatment. (orig.)

  2. Preparation,Characterization and Optical Properties of Hostguest Nanocomposite Material Mordenite—silver Iodide

    Institute of Scientific and Technical Information of China (English)

    ZHAIQing-zhou; QIUShi-lun

    2003-01-01

    Silver iodide nanoclusters were successfully prepared in the channels of mordenite by a heat diffusion method.Powder X-ray diffraction.adsorption technique and infrared spectroscopy were used to characterize the prepared materials,which showed that the guest silver iodied had been encapsulated in the channels of mordenite.The optical properties of the solid phase diffuse reflectance absorption of nanocomposite material NaM-AgI were studied,showing that the absorption bands of the diffuse reflectance absorption of the prepared material moved to the region of high energy.The absorption peak of the material prepared shifted to the region of high energy.Namely,blue shift was caused.This has demonstrated the incorporation of silver iodide into the channels of the zeolite.We observed the luminescence and surface photovoltage spectra of NaM-AgI sample,proposing the mechanisms of the photoluminescence and photovoltaic responses.

  3. Solvatochromic effect and kinetics of methyl violet reduction with potassium iodide in water-isopropanol mixtures

    Science.gov (United States)

    Ashfaq, Maria; Saeed, Rehana; Khan, Sameera Razi; Masood, Summyia

    2016-12-01

    The solvent influence on the reduction kinetics of methyl violet with iodide in binary mixture of aqueous isopropanol was investigated spectrophotometrically. The absorption spectra of methyl violet were recorded in water, aqueous isopropanol and absolute isopropanol. In these solvents λmax was in the range from 580.5 to 582.5 nm. The CNIBS/R-K model was used to calculate the solvatochromic parameters in a binary mixture; polynomial equation was also applied to describe the experimental data. The transition energies ( E T) were calculated. They show bathochromic shift with the decrease in the polarity of the solvent. The temperature was varied from 298-318 K, while the pH of the reaction was maintained at 4.99 and 6.00. The reduction reaction was found to be first order by potassium iodide and zero order by methyl violet. The thermodynamic parameters were also evaluated to support the kinetic data.

  4. Crystal structure of catena-poly[[potassium-tri-μ-dimethylacetamide-κ6O:O] iodide

    Directory of Open Access Journals (Sweden)

    Cezar-Catalin Comanescu

    2014-10-01

    Full Text Available The structure of catena-poly[[potassium-tri-μ-dimethylacetamide-κ6O:O] iodide], {[K(C4H9NO3]I}n, at 120 K has trigonal (P-3 symmetry. The structure adopts a linear chain motif parallel to the crystallographic c axis. Two crystallographically independent K+ cations are present in the asymmetric unit located on threefold rotoinversion axes at [0, 0, 0] and [0, 0, 1/2] and are bridged by the O atoms of the acetamide moiety. This is an example of a rare μ2-bridging mode for dimethylacetamide O atoms. The iodide counter-ion resides on a threefold rotation axis in the channel formed by the [K(C4H9NO]+ chains.

  5. Gastro-intestinal basidiobolomycosis in a 2-year-old boy: dramatic response to potassium iodide.

    Science.gov (United States)

    Sanaei Dashti, Anahita; Nasimfar, Amir; Hosseini Khorami, Hossein; Pouladfar, Gholamreza; Kadivar, Mohammad Rahim; Geramizadeh, Bita; Khalifeh, Masoomeh

    2016-07-04

    Gastro-intestinal basidiobolomycosis (GIB) is a rare fungal infection caused by Basidiobolus ranarum. Treatment includes surgical resection and long-term antifungal therapy. A 2.5-year-old boy presented with a 10-day history of abdominal pain, fever and diarrhoea, and a palpable abdominal mass was detected. Resection was undertaken and histology confirmed basidiobolomycosis. Treatment with amphotericin B and itraconazole was commenced, but the infection progressed and spread to involve the intestines, liver, ribs and lung, and also the abdominal wall after 6 months, requiring four operative procedures. Because of unresponsiveness to amphotericin and itraconazole, oral potassium iodide was added which resulted in complete resolution of the infection. Potassium iodide is an essential component of the treatment of systemic B. ranarum.

  6. Conclusion on the peer review of the pesticide risk assessment of the active substance potassium iodide

    Directory of Open Access Journals (Sweden)

    European Food Safety Authority

    2013-06-01

    Full Text Available The conclusions of the European Food Safety Authority (EFSA following the peer review of the initial risk assessments carried out by the competent authority of the rapporteur Member State the Netherlands, for the pesticide active substance potassium iodide are reported. The context of the peer review was that required by Commission Regulation (EU No 188/2011. The conclusions were reached on the basis of the evaluation of the representative uses of potassium iodide as a fungicide on tomatoes, sweet peppers, cucumber, eggplant, strawberries and ornamental flowers in greenhouse and field applications on strawberries. The reliable endpoints concluded as being appropriate for use in regulatory risk assessment, derived from the available studies and literature in the dossier peer reviewed, are presented. Missing information identified as being required by the regulatory framework is listed. Concerns are identified.

  7. Nitro-Grela-type complexes containing iodides – robust and selective catalysts for olefin metathesis under challenging conditions

    Directory of Open Access Journals (Sweden)

    Andrzej Tracz

    2015-10-01

    Full Text Available Iodide-containing nitro-Grela-type catalysts have been synthesized and applied to ring closing metathesis (RCM and cross metathesis (CM reactions. These new catalysts have exhibited improved efficiency in the transformation of sterically, non-demanding alkenes. Additional steric hindrance in the vicinity of ruthenium related to the presence of iodides ensures enhanced catalyst stability. The benefits are most apparent under challenging conditions, such as very low reaction concentrations, protic solvents or with the occurrence of impurities.

  8. Nitro-Grela-type complexes containing iodides – robust and selective catalysts for olefin metathesis under challenging conditions

    Science.gov (United States)

    Tracz, Andrzej; Matczak, Mateusz; Urbaniak, Katarzyna

    2015-01-01

    Summary Iodide-containing nitro-Grela-type catalysts have been synthesized and applied to ring closing metathesis (RCM) and cross metathesis (CM) reactions. These new catalysts have exhibited improved efficiency in the transformation of sterically, non-demanding alkenes. Additional steric hindrance in the vicinity of ruthenium related to the presence of iodides ensures enhanced catalyst stability. The benefits are most apparent under challenging conditions, such as very low reaction concentrations, protic solvents or with the occurrence of impurities. PMID:26664602

  9. Nitro-Grela-type complexes containing iodides - robust and selective catalysts for olefin metathesis under challenging conditions.

    Science.gov (United States)

    Tracz, Andrzej; Matczak, Mateusz; Urbaniak, Katarzyna; Skowerski, Krzysztof

    2015-01-01

    Iodide-containing nitro-Grela-type catalysts have been synthesized and applied to ring closing metathesis (RCM) and cross metathesis (CM) reactions. These new catalysts have exhibited improved efficiency in the transformation of sterically, non-demanding alkenes. Additional steric hindrance in the vicinity of ruthenium related to the presence of iodides ensures enhanced catalyst stability. The benefits are most apparent under challenging conditions, such as very low reaction concentrations, protic solvents or with the occurrence of impurities.

  10. Development and testing of a silver chloride-impregnated activated carbon for aqueous removal and sequestration of iodide.

    Science.gov (United States)

    Karanfil, T; Moro, E C; Serkiz, S M

    2005-11-01

    Silver impregnated activated carbon (SIAC) can effectively remove iodide from water and sequester it in the form of AgI(s)). Given the extremely insoluble nature of AgI(s), the spent SIAC can be safely disposed of in land burial facilities. However, when the molar ratio of silver to iodide is greater than one, which is typical for waters contaminated with iodide, unreacted silver on the SIAC leached into solution with decreasing pH. To minimize silver leaching, a silver chloride impregnated activated carbon (SIAC-Cl) was produced from a SIAC. Scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) and X-Ray Diffraction (XRD) analyses confirmed the presence of silver chloride on the SIAC-Cl. Batch isotherm experiments conducted at pH 5, 7 and 8 showed that the iodide uptakes of SIAC-Cl and SIAC were similar and independent of pH. SEM/EDX and XRD analyses after reaction with iodide indicated that chloride was exchanged with iodide to form AgI(s) on the SIAC-Cl. Batch leaching experiments demonstrated that leaching of silver from SIAC-Cl under acidic conditions was significantly lower than from SIAC. The performance of SIAC and SIAC-Cl for practical applications was evaluated by conducting column experiments using a radioactively contaminated groundwater that included 129I. SIAC and SIAC-Cl showed similar degrees of iodide uptake. However, a significant degree of silver leaching, about 50% of the total silver, occurred from the SIAC during the course of the column experiments, whereas silver leaching from SIAC-Cl was remarkably low (only 6% of the total silver). SIAC-Cl appears to be a suitable getter material to remove and sequester iodide from contaminated waste streams.

  11. Peroxide effects of iodide excess on mitochondria in Fischer rat thyroid cell line in the early period

    Institute of Scientific and Technical Information of China (English)

    李敏

    2014-01-01

    Objective To investigate the peroxide effects of iodide excess on mitochondria in Fischer rat thyroid cell line(FRTL)in the early period.Methods After treatment with 0.0 mmol/L(control group)or 0.1 mmol/L potassium iodide(KI)for 2,4 and 24 h,respectively,changes of mitochondrial superoxide formation were assayed by flow cytometry and fluorescence microscopy using mitochondria-targeted hydroethidine(Mito SOX).

  12. Effects of short-term potassium iodide treatment for thyrotoxicosis due to Graves disease in children and adolescents

    OpenAIRE

    Jeong, Kyung Uk; Lee, Hae Sang; Hwang, Jin Soon

    2014-01-01

    Purpose Graves disease is the most common cause of hyperthyroidism in children. Inorganic iodide has been used in combination with antithyroid drugs for more effective normalization of thyroid hormones in some cases of severe thyrotoxicosis. This study aimed to investigate clinical characteristics of childhood thyrotoxicosis and effectiveness of inorganic iodide in the early phase of treatment. Methods Sixty-seven pediatric patients (53 girls/14 boys, 11.1±3.4 years of age), with newly diagno...

  13. Study on Growth and Optical, Scintillation Properties of Thallium Doped Cesium Iodide –Scintillator Crystal

    Directory of Open Access Journals (Sweden)

    B. Ravi

    2014-06-01

    Full Text Available Single crystal of Thallium doped cesium Iodide –Scintillator crystal was grown using vertical Bridgeman technique. The grown crystal was included for cutting and polishing for the characterization purpose and this crystal was studied by optical transmission properties, photo luminescence and thermally luminescence characteristics. Gamma-ray detectors were fabricated using the grown crystal that showed good linearity and nearly 7.5% resolution at 662 keV.

  14. Rationale for the real-time and dynamic cell death assays using propidium iodide

    OpenAIRE

    Zhao, Hong; Oczos, Jadwiga; Janowski, Pawel; Trembecka, Dominika; Dobrucki, Jurek; Darzynkiewicz, Zbigniew; Wlodkowic, Donald

    2010-01-01

    We have recently reported an innovative approach to use charged fluorochromes such as propidium iodide (PI) in the real-time, dynamic cell viability assays. The present study was designed to provide a mechanistic rationale for the kinetic assays using cell permeability markers. Uptake of PI by live cells, effect on the cell cycle, long term proliferation capacity, DNA damage response and pharmacologic interactions with anticancer drugs were studied using both laser scanning microscopy and las...

  15. Studies on the Mechanisms of Methyl Iodide Adsorption and Iodine Retention on Silver-Mordenite

    Energy Technology Data Exchange (ETDEWEB)

    Nenoff, Tina Maria [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Soelberg, Nick [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-09-01

    Silver-containing mordenite (MOR) is a longstanding benchmark for radioiodine capture, reacting with molecular iodine (I2) to form AgI. However the mechanisms for organoiodine capture are not well understood. Here we investigate the capture of methyl iodide from complex mixed gas streams by combining chemical analysis of the effluent gas stream with in depth characterization of the recovered sorbent.

  16. Study on the Preparation and Characteristics of Cellulose/Silver Iodide Nanocomposite Film.

    Science.gov (United States)

    Lee, Yang Hun; Han, Sung Soo; Kang, Young Ah; Shin, Eun Joo

    2016-06-01

    In this study, the structure and properties of an organic-inorganic composite material prepared from cellulose doped with fine particles of silver iodide (AgI) were examined. The preparation of the composite involved the complexation of cellulose with polyiodide ions, such as I- and 13-, by immersion in iodine/potassium iodide (I2/KI: 0.2, 0.4, 0.6, 0.8, 1.0 M) or potassium iodide (KI: 0.6, 1.2, 1.8, 2.4, 3.0 M) aqueous solutions followed by reaction in a silver nitrate (AgNO3:1.0 M) aqueous solution. These procedures resulted in the in situ formation of fine β-AgI particles within the cellulose matrix. The characteristics and conductivities of prepared cellulose/silver iodide (AgI) nanocomposite films with different I2/KI and KI concentrations were investigated. AgI particle formation and aggregation increased on increasing I2/KI and KI concentrations as determined by SEM. X-ray results showed that KI could penetrate the cellulose crystal region and form AgI particles. The electrical conductivities of nanocomposite films treated with KI were higher than that of I2/KI at < 1.0 M of I2/KI and 3 M of KI, although the weight gain by AgI formation was lower than that of I2/KI. This was also attributed to the formation of smaller AgI particles and crystal defects. Highest electrical conductivity (3.8 x 10(-7) Ω(-1) cm(-1)) was obtained from the cellulose films (1.25 x 10(-11) Ω(-1) cm(-1)) treated with the aqueous solutions of 1.0 M I2/KI and 1.0 M AgNO3.

  17. Radiofrequency induction on sodium/iodide symporter expression of thyroid cancer

    Institute of Scientific and Technical Information of China (English)

    Youxin Tian; Qinjiang Liu; Yaqiong Ni

    2013-01-01

    Objective:The aim of this study was to investigate the ef ects of radiofrequency treatment on sodium/iodide symporter expression of thyroid cancer cells. Methods:In 29 thyroid cancer patients with low or no expression of soda\\iodide symporter, the radio frequency combined 131I therapy was used, the whole-body scintigraphy and serum Ig were detected before and after the radiofrequency treatment. Results:The whole-body scintigraphy showed that 4 cases (4/29) before radiofrequency treatment had positive iodine uptake, 19 cases (19/29) two weeks after radiofrequency treatment had the positive iodine uptake, 12 cases (12/29) four weeks after radiofrequency treatment had the positive iodine uptake. Four weeks after radiofrequency treatment, 5 cases had increased serum Ig levels, 17 cases had decreased serum Ig levels, 7 cases showed no change. 25 cases (25/29) were ef ective, 15 cases (15/29) were cured. Conclusion:The radiofrequency induced the non-expressed the sodium/iodide symporter of thyroid cancer cells regain the iodine intake ability, it improved the clinical ef icacy of 131I therapy in dedif erentiated thyroid cancer.

  18. Deteksi Natrium/Iodide Symporter (NIS pada Galur Sel Kanker Payudara SKBR3 dengan Imunositofluoresens

    Directory of Open Access Journals (Sweden)

    Aisyah Elliyanti

    2016-03-01

    Full Text Available SKBR-3 cell line is a breast cancer model for human epidermal growth factor receptor2 (HER2 positive. Only 50% of patients of this type have fully responded to chemotherapy. Natrium iodide symporter expression correlates with the uptake and ability of cells to accumulate radioiodine. The aim of this study was to examine natrium/iodide symporter (NIS expression and its distribution with and without epidermal growth factor (EGF treatment using immunocytofluoresence (ICF. This study was conducted at the Cell Culture Laboratory, Faculty of Medicine, Universitas Padjadjaran from September 2013 to April 2014. SKBR3 cells were cultured until 70% confluent. Cells were then divided into two groups: treatment group and control group. The treatment group was treated with EGF 50 ng/mL. Cells were incubated with primary antibody rabbit polyclonal antibody anti-NIS, and then were followed with secondary-antibody goat polyclonal antibody to rabbit. Data from the observation were then assessed semi-quantitatively. Natrium/iodide symporter was seen to be expressed and distributed in the cytoplasm. Cells induced by EGF showed significant increase in NIS expression in cytoplasm and its distribution in cell membrane. It is concluded that the SKBR3 cells express NIS in cytoplasm and that EGF induction increases NIS expression and distribution in cell membrane. This finding leads to a potential ability of breast cancer cells to uptake and accumulate radioiodine.

  19. Uptake of iodide by a mixture of metallic copper and cupric compounds

    Energy Technology Data Exchange (ETDEWEB)

    Lefevre, G.; Alnot, M.; Ehrhardt, J.J.; Bessiere, J. [Univ. Henri Poincare Nancy 1, Villers les Nancy (France). Lab. de Chimie Physique pour l`Environnement

    1999-05-15

    Environmental contaminants harmful to the health of present and future generations involve nuclear fission products as iodine radioisotopes. {sup 129}I is potentially one of the more mobile products because of its long half-life and its tendency to go into solution as an anion that is not retarded with silicate minerals. Ability of copper/cupric compound mixtures to remove iodide from solution was investigated to predict sorption of radioactive iodine in the environment and to assess their use in a nuclear reprocessing method. Thermodynamic calculations were performed to study the stability of such mixtures in solution and to obtain equilibrium constants of Cu(0)/Cu(II)/I{sup {minus}} and Cu(0)/Cu(II)/Cl{sup {minus}} systems. Both calculations and experimental results showed that a Cu(0)/Cu{sub 3}(OH){sub 2}(CO{sub 3}){sub 2} (azurite) mixture selectively uptakes iodide ions (initial concentrations: 10{sup {minus}2} and 10{sup {minus}1} M) in the presence of 10{sup {minus}1} M chloride ions. Reaction of iodide with copper powder and azurite crystal or copper plate and azurite powder have also been investigated, leading to precipitation of CuI onto massive copper phase. The different solids were separately analyzed by XPS and MEB-EDX, giving some insight in the uptake mechanism. It is proposed that soluble copper released by the cupric compound is reduced at the surface of metallic copper, leading to a preferential precipitation of CuI on copper surface.

  20. Use of potassium iodide in dermatology: updates on an old drug.

    Science.gov (United States)

    Costa, Rosane Orofino; Macedo, Priscila Marques de; Carvalhal, Aline; Bernardes-Engemann, Andréa Reis

    2013-01-01

    Potassium iodide, as a saturated solution, is a valuable drug in the dermatologist's therapeutic arsenal and is useful for the treatment of different diseases due to its immunomodulatory features. However, its prescription has become increasingly less frequent in dermatology practice. Little knowledge about its exact mechanism of action, lack of interest from the pharmaceutical industry, the advent of new drugs, and the toxicity caused by the use of high doses of the drug are some possible explanations for that. Consequently, there are few scientific studies on the pharmacological aspects, dosage and efficacy of this drug. Also, there is no conventional standard on how to manipulate and prescribe the saturated solution of potassium iodide, which leads to unawareness of the exact amount of the salt being delivered in grams to patients. Considering that dosage is directly related to toxicity and the immunomodulatory features of this drug, it is essential to define the amount to be prescribed and to reduce it to a minimum effective dose in order to minimize the risks of intolerance and thus improve treatment adherence. This review is relevant due to the fact that the saturated solution of potassium iodide is often the only therapeutic choice available for the treatment of some infectious, inflammatory and immune-mediated dermatoses, no matter whether the reason is specific indication, failure of a previous therapy or cost-effectiveness.

  1. Toxic impact of bromide and iodide on drinking water disinfected with chlorine or chloramines.

    Science.gov (United States)

    Yang, Yang; Komaki, Yukako; Kimura, Susana Y; Hu, Hong-Ying; Wagner, Elizabeth D; Mariñas, Benito J; Plewa, Michael J

    2014-10-21

    Disinfectants inactivate pathogens in source water; however, they also react with organic matter and bromide/iodide to form disinfection byproducts (DBPs). Although only a few DBP classes have been systematically analyzed for toxicity, iodinated and brominated DBPs tend to be the most toxic. The objectives of this research were (1) to determine if monochloramine (NH2Cl) disinfection generated drinking water with less toxicity than water disinfected with free chlorine (HOCl) and (2) to determine the impact of added bromide and iodide in conjunction with HOCl or NH2Cl disinfection on mammalian cell cytotoxicity and genomic DNA damage induction. Water disinfected with chlorine was less cytotoxic but more genotoxic than water disinfected with chloramine. For both disinfectants, the addition of Br(-) and I(-) increased cytotoxicity and genotoxicity with a greater response observed with NH2Cl disinfection. Both cytotoxicity and genotoxicity were highly correlated with TOBr and TOI. However, toxicity was weakly and inversely correlated with TOCl. Thus, the forcing agents for cytotoxicity and genotoxicity were the generation of brominated and iodinated DBPs rather than the formation of chlorinated DBPs. Disinfection practices need careful consideration especially when using source waters containing elevated bromide and iodide.

  2. Simple and rapid determination of iodide in table salt by stripping potentiometry at a carbon-paste electrode.

    Science.gov (United States)

    Svancara, Ivan; Ogorevc, Bozidar; Nović, Milko; Vytras, Karel

    2002-04-01

    A simple and rapid procedure, utilising constant-current stripping analysis (CCSA) at a carbon-paste electrode containing tricresyl phosphate as a pasting liquid (TCP-CPE), has been developed for the determination of iodide in table salt. Because of a synergistic accumulation mechanism based on ion-pairing and extraction of iodide in combination with electrolytic pretreatment of the TCP-CPE, the method is selective for iodide and enables direct determination of iodide in samples of table salt containing anti-caking agents such as K(4)[Fe(CN)(6)] (food additive "E 536") or MgO. The iodide content (calculated as KI) can be determined in a concentration range of 2 to 100 mg kg(-1) salt, with a detection limit (S/N=3) of 1 mg kg(-1), and a recovery from 90 to 115%. The proposed method has been used to determine iodide in several types of artificially iodised table salt and in one sample of natural sea salt. The results obtained agreed well with those obtained by use of three independent reference methods (titration, spectrophotometry, and ICP-MS) used to validate the CCSA method, indicating that the developed method is applicable as a routine procedure for rapid testing in salt production process control and in the analysis of marketed table salts.

  3. Activation of the Nrf2-Keap 1 Pathway in Short-Term Iodide Excess in Thyroid in Rats

    Directory of Open Access Journals (Sweden)

    Tingting Wang

    2017-01-01

    Full Text Available Wistar rats were randomly divided into groups of varying iodide intake: normal iodide; 10 times high iodide; and 100 times high iodide on Days 7, 14, and 28. Insignificant changes were observed in thyroid hormone levels (p>0.05. Urinary iodine concentration and iodine content in the thyroid glands increased after high consumption of iodide from NI to 100 HI (p<0.05. The urinary iodine concentration of the 100 HI group on Days 7, 14, and 28 was 60–80 times that of the NI group. The mitochondrial superoxide production and expressions of Nrf2, Srx, and Prx 3 all significantly increased, while Keap 1 significantly decreased in the 100 HI group when compared to the NI or 10 HI group on Days 7, 14, and 28 (p<0.05. Immunofluorescence staining results showed that Nrf2 was localized in the cytoplasm in NI group. Although Nrf2 was detected in both cytoplasm and nucleus in 10 HI and 100 HI groups, a stronger positive staining was found in the nucleus. We conclude that the activation of the Nrf2-Keap 1 antioxidative defense mechanism may play a crucial role in protecting thyroid function from short-term iodide excess in rats.

  4. Activation of the Nrf2-Keap 1 Pathway in Short-Term Iodide Excess in Thyroid in Rats

    Science.gov (United States)

    Liang, Xue

    2017-01-01

    Wistar rats were randomly divided into groups of varying iodide intake: normal iodide; 10 times high iodide; and 100 times high iodide on Days 7, 14, and 28. Insignificant changes were observed in thyroid hormone levels (p > 0.05). Urinary iodine concentration and iodine content in the thyroid glands increased after high consumption of iodide from NI to 100 HI (p Prx 3 all significantly increased, while Keap 1 significantly decreased in the 100 HI group when compared to the NI or 10 HI group on Days 7, 14, and 28 (p < 0.05). Immunofluorescence staining results showed that Nrf2 was localized in the cytoplasm in NI group. Although Nrf2 was detected in both cytoplasm and nucleus in 10 HI and 100 HI groups, a stronger positive staining was found in the nucleus. We conclude that the activation of the Nrf2-Keap 1 antioxidative defense mechanism may play a crucial role in protecting thyroid function from short-term iodide excess in rats. PMID:28133506

  5. [The effect of long-term external ionizing radiation on the functional activity of rat thyroid under enhanced potassium iodide consumption].

    Science.gov (United States)

    Lupachik, S V; Nadol'nik, L I

    2008-01-01

    The study was devoted to the effect of long-term (20 days) external ionizing radiation at a dose of 0.5 Gy on the iodide metabolism in the rat thyroid under supplementation of high iodine doses (10 daily KI doses). It was found that the potassium iodide administration partially prevented the effects of a post radiation decrease of serum thyroid hormone levels (the level of T4 was normal and that of T3 was 77.4% of the controls). After the supplementation of 10 daily iodide doses, the rat thyroid tissue showed the most pronounced increase in the levels of total, free and protein-bound iodide compared to the groups of animals consuming normal and elevated KI doses. Pronounced inhibition of thyroid peroxidase activity (3.1-fold) was noted in the same group. The data obtained indicate a radiation-induced activation of iodide uptake during its enhanced supplementation and disturbed iodide enzymatic oxidation and organification.

  6. [The analysis for silver iodide fine particles of TLC/FTIR matrix].

    Science.gov (United States)

    Zhu, Qing; Su, Xiao; Wu, Hai-Jun; Zhai, Yan-Jun; Xia, Jin-Ming; Buhebate; Xu, Yi-Zhuang; Wu, Jin-Guang

    2012-07-01

    In situ TLC/FTIR technique has tremendous potential in the analysis of complex mixtures. However, the progress in this technique was quite slow. The reason is that conventional stationary phase has strong absorption in FTIR spectrum and thus brings about severe interference in the detection of samples. To solve the problem, the authors propose to use AgI fine particles as stationary phase of TLC plate. The reasons are as follows: Silver iodide fine particles have no absorbance in an IR region between 4 000 and 800 cm(-1), therefore, the interference caused by IR absorption of stationary phase can be removed. Moreover, silver iodide is stable and insolvable in water and organic solvents and thus it will not be destroyed by mobile phase or react with samples during the TLC separation. To improve TLC separation efficiency and quality of FTIR spectra during the TLC/FTIR analysis, the size of AgI particles should be below 500 nm. We used orthogonal design approach to optimize the experimental condition to AgI particles so that the average size of AgI particles is around 100 nm. No absorption of impurity or adsorbed water were observed in FTIR spectrum of the AgI particles the authors used "settlement volatilization method" to prepare TLC plate without using polymeric adhesive that may bring about significant interference in FTIR analysis. Preliminary TLC experiments proved that the TLC plate using AgI fine particles as stationary phase can separate mixtures of rhodamine B and bromophenol blue successfully. Applications of silver iodide fine particles as stationary phase have bright perspective in the development of in-situ TLC/FTIR analysis techniques.

  7. Titrimetric and spectrophotometric assay of diethylcarbamazine citrate in formulations using iodate and iodide mixture as reagents

    Directory of Open Access Journals (Sweden)

    Nagaraju Swamy

    2015-03-01

    Full Text Available One titrimetric and two spectrophotometric methods are proposed for the determination of diethylcarbamazine citrate (DEC in bulk drug and in formulations using potassium iodate and potassium iodide as reagent. The methods employ the well-known analytical reaction between iodate and iodide in the presence of acid. In titrimetry (method A, the drug was treated with a measured excess of thiosulfate in the presence of unmeasured excess of iodate-iodide mixture and after a standing time of 10 min, the surplus thiosulfate was determined by back titration with iodine towards starch end point. Titrimetric assay is based on a 1:3 reaction stoichiometry between DEC and iodine and the method is applicable over 2.0-10.0 mg range. The liberated iodine is measured spectrophotometrically at 370 nm (method B or the iodine-starch complex measured at 570 nm (method C. In both methods, the absorbance is found to be linearly dependent on the concentration of iodine, which in turn is related to DEC concentration. The calibration curves are linear over 2.5-50 and 2.5-30 µg mL-1 DEC for method B and method C, respectively. The calculated molar absorptivity and Sandell sensitivity values were 6.48×103 L mol-1 cm-1 and 0.0604 µg cm-2, respectively, for method B, and their respective values for method C are 9.96×103 L mol-1 cm-1 and 0.0393 µg cm-2. The intra-day and inter-day accuracy and precision studies were carried out according to the ICH guidelines. The methods were successfully applied to the analysis of DEC formulations.

  8. Equations of state for crystalline zirconium iodide: The role of dispersion

    Energy Technology Data Exchange (ETDEWEB)

    Rossi, Matthew L., E-mail: mrossi@lanl.gov [Materials Science and Technology, MST-6, Los Alamos National Lab, Los Alamos, NM (United States); Taylor, Christopher D. [Materials Science and Technology, MST-6, Los Alamos National Lab, Los Alamos, NM (United States)

    2013-02-15

    We present the first-principle equations of state of several zirconium iodides, ZrI{sub 2}, ZrI{sub 3}, and ZrI{sub 4}, computed using density functional theory methods that apply various methods for introducing the dispersion correction. Iodides formed due to reaction of molecular or atomic iodine with zirconium and zircaloys are of particular interest due to their application to the cladding material used in the fabrication of nuclear fuel rods. Stress corrosion cracking (SCC), associated with fission product chemistry with the clad material, is a major concern in the life cycle of nuclear fuels, as many of the observed rod failures have occurred due to pellet–cladding chemical interactions (PCCI) [A. Atrens, G. Dannhäuser, G. Bäro, Stress-corrosion-cracking of zircaloy-4 cladding tubes, Journal of Nuclear Materials 126 (1984) 91–102; P. Rudling, R. Adamson, B. Cox, F. Garzarolli, A. Strasser, High burn-up fuel issues, Nuclear Engineering and Technology 40 (2008) 1–8]. A proper understanding of the physical properties of the corrosion products is, therefore, required for the development of a comprehensive SCC model. In this particular work, we emphasize that, while existing modeling techniques include methods to compute crystal structures and associated properties, it is important to capture intermolecular forces not traditionally included, such as van der Waals (dispersion) correction. Furthermore, crystal structures with stoichiometries favoring a high I:Zr ratio are found to be particularly sensitive, such that traditional density functional theory approaches that do not incorporate dispersion incorrectly predict significantly larger volumes of the lattice. This latter point is related to the diffuse nature of the iodide electron cloud.

  9. The sphingosine 1-phosphate receptor modulator FTY720 prevents iodide-induced autoimmune thyroiditis in non-obese diabetic mice.

    Science.gov (United States)

    Morohoshi, Kazuki; Osone, Michiko; Yoshida, Katsumi; Nakagawa, Yoshinori; Hoshikawa, Saeko; Ozaki, Hiroshi; Takahashi, Yurie; Ito, Sadayoshi; Mori, Kouki

    2011-09-01

    FTY720 is an immunomodulator that alters migration and homing of lymphocytes via sphingosine 1-phosphate receptors. This compound has been shown to be effective in suppressing autoimmune diseases in experimental and clinical settings. In the present study, we tested whether FTY720 prevented autoimmune thyroiditis in iodide-treated non-obese diabetic (NOD) mice, a model of Hashimoto's thyroiditis (HT) in humans. Mice were given 0.05% iodide water for 8 weeks, and this treatment effectively induced thyroiditis. Iodide-treated mice were injected intraperitoneally with either saline or FTY720 during the iodide treatment. FTY720 clearly suppressed the development of thyroiditis and reduced serum anti-thyroglobulin antibody levels. The number of circulating lymphocytes and spleen cells including CD4(+) T cells, CD8(+) T cells, and CD4(+)Foxp3(+) T cells was decreased in FTY720-treated mice. Our results indicate that FTY720 has immunomodulatory effects on iodide-induced autoimmune thyroiditis in NOD mice and may be a potential candidate for use in the prevention of HT.

  10. Crystal Growth and Dissolution of Methylammonium Lead Iodide Perovskite in Sequential Deposition: Correlation between Morphology Evolution and Photovoltaic Performance.

    Science.gov (United States)

    Hsieh, Tsung-Yu; Huang, Chi-Kai; Su, Tzu-Sen; Hong, Cheng-You; Wei, Tzu-Chien

    2017-03-01

    Crystal morphology and structure are important for improving the organic-inorganic lead halide perovskite semiconductor property in optoelectronic, electronic, and photovoltaic devices. In particular, crystal growth and dissolution are two major phenomena in determining the morphology of methylammonium lead iodide perovskite in the sequential deposition method for fabricating a perovskite solar cell. In this report, the effect of immersion time in the second step, i.e., methlyammonium iodide immersion in the morphological, structural, optical, and photovoltaic evolution, is extensively investigated. Supported by experimental evidence, a five-staged, time-dependent evolution of the morphology of methylammonium lead iodide perovskite crystals is established and is well connected to the photovoltaic performance. This result is beneficial for engineering optimal time for methylammonium iodide immersion and converging the solar cell performance in the sequential deposition route. Meanwhile, our result suggests that large, well-faceted methylammonium lead iodide perovskite single crystal may be incubated by solution process. This offers a low cost route for synthesizing perovskite single crystal.

  11. Electrical properties of solid iodo mercurates resulting from the reaction of HgI2 with alcaline iodides

    Science.gov (United States)

    Ponpon, J. P.; Amann, M.

    2005-01-01

    Potassium iodide solutions are currently used during the fabrication process of mercuric iodide based nuclear radiation detectors. However, KI treatment leaves the HgI2 surface covered with a residual compound (namely the potassium tri-iodo mercurate) which has a significant influence on the surface properties and stability of mercuric iodide devices and therefore on the detectors characteristics. Looking for other solutions to etch mercuric iodide, we found it interesting to investigate the electrical properties of the compounds which may form when etching HgI2 in NH4I, NaI, and RbI. For this purpose, solid iodo mercurates with the cations ammonium, sodium, and rubidium, have been prepared by reacting HgI2 with the solutions of interest. Study of the electrical properties of these samples and comparison with those of potassium tri-iodo mercurate ones, especially with respect to humidity, indicates noticeable stability differences in presence of water vapour. This could have interesting consequences on the surface cleaning of mercuric iodide.

  12. A novel vortex-assisted liquid-liquid microextraction approach using auxiliary solvent: Determination of iodide in mineral water samples.

    Science.gov (United States)

    Zaruba, Serhii; Vishnikin, Andriy B; Andruch, Vasil

    2016-01-01

    A novel vortex-assisted liquid-liquid microextraction (VA-LLME) for determination of iodide was developed. The method includes the oxidation of iodide with iodate in the presence of hydrochloric acid followed by VA-LLME of the ion-pair formed between ICl2(-) and Astra Phloxine reagent (AP) and subsequent absorbance measurement at 555nm. The appropriate experimental conditions were investigated and found to be: 5mL of sample, 0.27molL(-)(1) HCl, 0.027mmolL(-1) KIO3 as the oxidation agent, 250μL of extraction mixture containing amyl acetate as the extraction solvent and carbon tetrachloride as the auxiliary solvent (1:1, v/v), 0.04mmolL(-1) AP reagent, vortex time: 20s at 3000rpm, centrifugation: 4min at 3000rpm. The calibration plot was linear in the range 16.9-169μg L(-1) of iodide, with a correlation coefficient (R(2)) of 0.996, and the relative standard deviation ranged from 1.9 to 5.7%. The limit of detection (LOD) and limit of quantification (LOQ) were 1.75 and 6.01μgL(-)(1) of iodide, respectively. The suggested procedure was applied for determination of iodide in real mineral water samples.

  13. An iodine supplementation of tomato fruits coated with an edible film of the iodide-doped chitosan.

    Science.gov (United States)

    Limchoowong, Nunticha; Sricharoen, Phitchan; Techawongstien, Suchila; Chanthai, Saksit

    2016-06-01

    In general, the risk of numerous thyroid cancers inevitably increases among people with iodine deficiencies. An iodide-doped chitosan (CT-I) solution was prepared for dipping tomatoes to coat the fresh surface with an edible film (1.5 μm), thereby providing iodine-rich fruits for daily intake. Characterisation of the thin film was conducted by FTIR and SEM. Stability of the CT-I film was studied via water immersion at various time intervals, and no residual iodide leached out due to intrinsic interactions between the cationic amino group of chitosan and iodide ions. Moreover, the iodide supplement exhibited no effect on the antioxidant activity of tomatoes. The iodine content in the film-coated tomato was determined by ICP-OES. The tomato coating with 1.5% (w/v) CT-I contained approximately 0.4 μg iodide per gram fresh weight. In addition, the freshness and storability of iodine-doped tomatoes were also maintained for shelf-life concerns.

  14. Towards Renewable Iodide Sources for Electrolytes in Dye-Sensitized Solar Cells

    Directory of Open Access Journals (Sweden)

    Iryna Sagaidak

    2016-03-01

    Full Text Available A novel family of iodide salts and ionic liquids based on different carbohydrate core units is herein described for application in dye-sensitized solar cell (DSC. The influence of the molecular skeleton and the cationic structure on the electrolyte properties, device performance and on interfacial charge transfer has been investigated. In combination with the C106 polypyridyl ruthenium sensitizer, power conversion efficiencies lying between 5.0% and 7.3% under standard Air Mass (A.M. 1.5G conditions were obtained in association with a low volatile methoxypropionitrile (MPN-based electrolyte.

  15. Performance of neutron activation analysis in the evaluation of bismuth iodide purification methodology

    Energy Technology Data Exchange (ETDEWEB)

    Armelin, Maria Jose A.; Ferraz, Caue de Mello; Hamada, Margarida M., E-mail: marmelin@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Lab. de Analise por Ativacao Neutronica

    2015-07-01

    Bismuth tri-iodide (BrI{sub 3}) is an attractive material for using as a semiconductor. In this paper, BiI{sub 3} crystals have been grown by the vertical Bridgman technique using commercially available powder. The impurities were evaluated by instrumental neutron activation analysis (INAA). The results show that INAA is an analytical method appropriate for monitoring the impurities of: Ag, As, Br, Cr, K, Mo, Na and Sb in the various stages of the BiI{sub 3} purification methodology. (author)

  16. Introduction to fifth international workshop on mercuric iodide nuclear radiation detectors

    Energy Technology Data Exchange (ETDEWEB)

    Schieber, M.

    1982-01-01

    Mercuric iodide is a wide bandgap semiconductor, with Eg approx. = 2.14 eV at room temperature. Therefore, HgI/sub 2/ is totally different from the well-studied, narrower gap, elemental semiconductors such as Si and Ge, and also different in its physical and chemical properties from the known semiconductor binary zinc-blend compounds such as GaAs or InP. The purpose of studies in the last decade was to further our understanding of HgI/sub 2/; recent progress is reported. (WHK)

  17. Effects of Aromatic Ammoniums on Methyl Ammonium Lead Iodide Hybrid Perovskite Materials

    Directory of Open Access Journals (Sweden)

    Jianli Yang

    2017-01-01

    Full Text Available The introduction of bulky ammoniums into methyl ammonium lead iodide hybrid perovskites (MAPbI3 has emerged as a promising strategy to improve the properties of these materials. In the present work, we studied the effects of several aromatic ammoniums onto the structural, electronic, and optical properties of MAPbI3. Although powder XRD data suggest that the bulky cations are not involved in the bulk phase of the MAPbI3, a surprisingly large effect of the bulky cations onto the photoluminescence properties was observed.

  18. Nucleophilic addition to the ethynyl group in ethynylestradiol catalyzed by crown ether-copper (1) iodide.

    Science.gov (United States)

    Chen, S H; Luo, G R; Chang, X Z; Zhao, H M

    1991-10-01

    A new and convenient synthetic route to acetylation of estrogens is described. Benzo-15-crown-5 and cuprous iodide-mixed catalyst catalyzed the nucleophilic addition of 2,4-dibromoethynylestradiol, resulting in the formation of a new compound, 2,4-dibromo-17 alpha-acetylestradiol, of which the structure was characterized by infrared, UV, 1H nuclear magnetic resonance, mass spectra, and elemental analysis. It was found that the yield of this approach is much higher than that obtained in the hydration of usual acetylenic compounds.

  19. Subcutaneous Zygomycosis: A Report of One Case Responding Excellently to Potassium Iodide.

    Science.gov (United States)

    Mondal, Ashim Kr; Saha, Abhijit; Seth, Joly; Mukherjee, Soumya

    2015-01-01

    Subcutaneous Zygomycosis is a rare opportunistic fungal infection caused by Basidiobolus ranarum. Though this entity is endemic in South India, limited numbers of cases have been reported from this part of the country. We report a case of subcutaneous zygomycosis in a 25 year old lady who presented with a nontender, firm to hard swelling over the upper-left arm. Finger was easily inserted below the indurated edge. Histopathology revealed suppurative granuloma with aseptate hyphae. Patient responded excellently to saturated solution of potassium iodide in subsequent visits.

  20. Spectroscopy of stop bands in artificial opals filled with an alcohol solution of potassium iodide

    Science.gov (United States)

    Gorelik, V. S.; Filatov, V. V.

    2012-09-01

    The spectral position of the stop bands in photonic crystals based on artificial opals filled with an alcohol solution of potassium iodide is investigated. The energy-band structure of samples with quartz globules 230 nm in diameter is modeled based on the dispersion equation. The spectral position of the stop bands in the [111] direction at different solution concentrations is determined. The conditions for forbidden-band "collapse" are established. The possibility of applying artificial opals in optical cavities of lasers of different types is analyzed.

  1. Subcutaneous zygomycosis: A report of one case responding excellently to potassium iodide

    Directory of Open Access Journals (Sweden)

    Ashim Kr Mondal

    2015-01-01

    Full Text Available Subcutaneous Zygomycosis is a rare opportunistic fungal infection caused by Basidiobolus ranarum. Though this entity is endemic in South India, limited numbers of cases have been reported from this part of the country. We report a case of subcutaneous zygomycosis in a 25 year old lady who presented with a nontender, firm to hard swelling over the upper-left arm. Finger was easily inserted below the indurated edge. Histopathology revealed suppurative granuloma with aseptate hyphae. Patient responded excellently to saturated solution of potassium iodide in subsequent visits.

  2. Atypical Cutaneous Sporotrichosis in an Immunocompetent Adult: Response to Potassium Iodide.

    Science.gov (United States)

    Gandhi, Nikita; Chander, Ram; Jain, Arpita; Sanke, Sarita; Garg, Taru

    2016-01-01

    Cutaneous sporotrichosis, also known as "Rose Gardener's disease," caused by dimorphic fungus Sporothrix schenkii, is usually characterized by indolent nodular or nodulo-ulcerative lesions arranged in a linear pattern. We report bizarre nonlinear presentation of Sporotrichosis, in an immunocompetent adult occurring after a visit to Amazon rain forest, speculating infection with more virulent species of Sporothrix. The diagnosis was reached with the help of periodic acid-Schiff positive yeast cells and cigar shaped bodies seen in skin biopsy along with the therapeutic response to potassium iodide.

  3. Successful Therapy of Refractory Erythema Nodosum Associated with Crohn's Disease Using Potassium Iodide

    Directory of Open Access Journals (Sweden)

    John K Marshall

    1997-01-01

    Full Text Available Erythema nodosum is a common extraintestinal manifestation of Crohn's disease. While mild skin involvement often responds to conservative management, severe or refractory cases may require systemic corticosteroid or immunosuppressive therapy. This report describes successful treatment of severe, refractory erythema nodosum associated with Crohn's colitis using oral potassium iodide. While the mechanism of action of this agent is poorly understood, it appears to be an effective and nontoxic therapy for Crohn's-related erythema nodosum and warrants further evaluation in a placebo controlled trial.

  4. Growth and characterization of NLO crystal: L-leucine phthalic acid potassium iodide

    OpenAIRE

    Jagadeesh M.R.; Kumar H .M. Suresh; Kumari R. Ananda

    2015-01-01

    A new semi-organic non linear optical crystal, L-leucine phthalic acid potassium iodide (LLPPI) has been grown from an aqueous solution by slow evaporation method. The grown crystals were subjected to different characterizations, such as single crystal XRD, FT-IR, UV-Vis, TGA, SEM, EDAX, micro hardness, dielectric and powder SHG. Single crystal structure was determined from X-ray diffraction data and it revealed that the crystal belongs to triclinic system with the space group P1. The vibrati...

  5. Real-Time Observation of Organic Cation Reorientation in Methylammonium Lead Iodide Perovskites

    OpenAIRE

    2015-01-01

    This document is the Accepted Manuscript version of a Published Work that appeared in final form in The Journal of Physical Chemistry Letters, copyright © American Chemical Society after peer review and technical editing by the publisher. To access the final edited and published work see http://pubs.acs.org/doi/abs/10.1021/acs.jpclett.5b01555 The introduction of a mobile and polarized organic moiety as a cation in 3D lead-iodide perovskites brings fascinating optoelectronic properties to t...

  6. Atypical cutaneous sporotrichosis in an immunocompetent adult: Response to potassium iodide

    Directory of Open Access Journals (Sweden)

    Nikita Gandhi

    2016-01-01

    Full Text Available Cutaneous sporotrichosis, also known as “Rose Gardener's disease,” caused by dimorphic fungus Sporothrix schenkii, is usually characterized by indolent nodular or nodulo-ulcerative lesions arranged in a linear pattern. We report bizarre nonlinear presentation of Sporotrichosis, in an immunocompetent adult occurring after a visit to Amazon rain forest, speculating infection with more virulent species of Sporothrix. The diagnosis was reached with the help of periodic acid-Schiff positive yeast cells and cigar shaped bodies seen in skin biopsy along with the therapeutic response to potassium iodide.

  7. Zinc iodide-osmium staining of membrane-coating granules in keratinized and non-keratinized mammalian oral epithelium.

    Science.gov (United States)

    Squier, C A

    1982-01-01

    Specimens of keratinized and non-keratinized oral epithelium were examined in the electron microscope after being stained with zinc iodide-osmium. In both types of tissue, reaction was seen in unmyelinated nerves, in the specific granules of epithelial Langerhans cells and within lysosome-like organelles and small vesicles associated with Golgi systems. In keratinized epithelia, the reaction was also present in the membrane-coating granules and between the deepest cells of the keratinized layer. In contrast, the membrane-coating granules of non-keratinized epithelia lacked Zn iodide-osmium staining despite the presence of reaction in adjacent Golgi systems. It is suggested that Zn iodide-osmium stains glycolipid or glycoprotein material in the cell. This material is elaborated in the Golgi systems from which lysosomes and the membrane-coating granules of keratinized tissues are probably derived.

  8. Colorimetric Solid Phase Extraction for the Measurement of Total I (Iodine, Iodide, and Triiodide) in Spacecraft Drinking Water

    Science.gov (United States)

    Lipert, Robert J.; Porter, Marc D.; Siperko, Lorraine M.; Gazda, Daniel B.; Rutz, Jeff A.; Schultz, John R.; Carrizales, Stephanie M.; McCoy, J. Torin

    2009-01-01

    An experimental drinking water monitoring kit for the measurement of iodine and silver(I) was recently delivered to the International Space Station (ISS). The kit is based on Colorimetric Solid Phase Extraction (CSPE) technology, which measures the change in diffuse reflectance of indicator disks following exposure to a water sample. To satisfy additional spacecraft water monitoring requirements, CSPE has now been extended to encompass the measurement of total I (iodine, iodide, and triiodide) through the introduction of an oxidizing agent, which converts iodide and triiodide to iodine, for measurement using the same indicator disks currently being tested on ISS. These disks detect iodine, but are insensitive to iodide and triiodide. We report here the operational considerations, design, and ground-based performance of the CSPE method for total I. The results demonstrate that CSPE technology is poised to meet NASA's total I monitoring requirements.

  9. Bio-inspired stabilization of sulfenyl iodide RS-I in a Zr(IV)-based metal-organic framework.

    Science.gov (United States)

    Yee, Ka-Kit; Wong, Yan-Lung; Xu, Zhengtao

    2016-03-28

    A Zr(IV)-based metal-organic framework (MOF) appended with free-standing thiol (-SH) groups was found to react readily with I2 molecules to form sulfenyl iodide (S-I) units. In contrast to its solution chemistry of facile disproportionation into disulfide and I2, the sulfenyl iodide (SI) function, anchored onto the rigid MOF grid and thus prevented from approaching one another to undergo the dismutation reaction, exhibits distinct stability even at elevated temperatures (e.g., 90 °C). On a conceptual plane, this simple and effective solid host also captures the spatial confinement observed for the complex biomacromolecular scaffolds involved in iodine thyroid chemistry, wherein the spatial isolation and consequent stabilization of sulfenyl/selenenyl iodides are exerted by means of the protein scaffolds.

  10. Synthesis of 1-/sup 11/C-labelled ethyl, propyl, butyl and isobutyl iodides and examples of alkylation reactions

    Energy Technology Data Exchange (ETDEWEB)

    Laangstroem, B.; Antoni, G.; Gullberg, P.; Halldin, C.; Naagren, K.; Rimland, A.; Svaerd, H.

    1986-01-01

    New /sup 11/C-labelled precursors (1-/sup 11/C)ethyl,(1-/sup 11/C)propyl, (1-/sup 11/C)butyl, and (1-/sup 11/C)isobutyl iodides have been prepared by a 3-step reaction route using a one-pot system. The labelled iodides were obtained in 20-55% radiochemical yields and 65-95% radiochemical purities, with a total time for synthesis of the order of 10-14 min. The labelled iodides have been used in alkylation reactions with nitrogen, oxygen and carbon nucleophiles. The nitrogen alkylation reactions are exemplified by the synthesis of the analgetics N-(1-/sup 11/C-ethyl)iodocaine and N-(1-/sup 11/C-butyl) bupivacaine. The synthesis of 3-nitrophenyl(1-/sup 11/C)propyl ether is also presented in this paper as an example of an oxygen alkylation.

  11. Heat capacity and density of potassium iodide solutions in mixed N-methylpyrrolidone-water solvent at 298.15 K

    Science.gov (United States)

    Novikov, A. N.

    2014-10-01

    The heat capacity and density of potassium iodide solutions in a mixed N-methylpyrrolidone (MP)-water solvent with a low content of the organic component are measured via calorimetry and densimetry at 298.15 K. Standard partial molal heat capacities and volumes of potassium iodide in MP-water mixtures are calculated. Standard heat capacities and volumes of potassium and iodide ions are determined. The character of the changes in heat capacity and volume are discussed on the basis of calculating additivity coefficients δ c and δ v upon the mixing of isomolal binary solutions KI-MP and KI-water, depending on the composition of the MP-H2O mixture and the concentration of the electrolyte.

  12. Phase diagram of an iodine-potassium iodide-water-ethanol system at 25°C

    Science.gov (United States)

    Varlamova, T. M.; Rubtsova, E. M.; Mushtakova, S. P.

    2012-09-01

    Phase equilibriums are studied in the isothermal-isobaric sections of the phase diagram of a fourcomponent iodine-potassium iodide-water-ethanol system at 25°C and atmospheric pressure. The compositions of the solvent at which it exhibits the greatest ability to dissolve iodine are established. It is shown that in all the investigated sections, there is three-phase eutonic equilibrium with potassium iodide and crystalline iodine as the solid phases. It is revealed that in the sections containing 30 and 50% of ethanol, potassium iodide serves as the salting in agent for crystalline iodine, due to the formation of polyiodide complexes of various composition in the studied system.

  13. Analysis of heterogeneous water vapor uptake by metal iodide cluster ions via differential mobility analysis-mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Oberreit, Derek [Department of Mechanical Engineering, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Fluid Measurement Technologies, Inc., Saint Paul, Minnesota 55110 (United States); Rawat, Vivek K.; Larriba-Andaluz, Carlos; Ouyang, Hui; McMurry, Peter H.; Hogan, Christopher J., E-mail: hogan108@umn.edu [Department of Mechanical Engineering, University of Minnesota, Minneapolis, Minnesota 55455 (United States)

    2015-09-14

    The sorption of vapor molecules onto pre-existing nanometer sized clusters is of importance in understanding particle formation and growth in gas phase environments and devising gas phase separation schemes. Here, we apply a differential mobility analyzer-mass spectrometer based approach to observe directly the sorption of vapor molecules onto iodide cluster ions of the form (MI){sub x}M{sup +} (x = 1-13, M = Na, K, Rb, or Cs) in air at 300 K and with water saturation ratios in the 0.01-0.64 range. The extent of vapor sorption is quantified in measurements by the shift in collision cross section (CCS) for each ion. We find that CCS measurements are sensitive enough to detect the transient binding of several vapor molecules to clusters, which shift CCSs by only several percent. At the same time, for the highest saturation ratios examined, we observed CCS shifts of up to 45%. For x < 4, cesium, rubidium, and potassium iodide cluster ions are found to uptake water to a similar extent, while sodium iodide clusters uptake less water. For x ≥ 4, sodium iodide cluster ions uptake proportionally more water vapor than rubidium and potassium iodide cluster ions, while cesium iodide ions exhibit less uptake. Measured CCS shifts are compared to predictions based upon a Kelvin-Thomson-Raoult (KTR) model as well as a Langmuir adsorption model. We find that the Langmuir adsorption model can be fit well to measurements. Meanwhile, KTR predictions deviate from measurements, which suggests that the earliest stages of vapor uptake by nanometer scale species are not well described by the KTR model.

  14. Analysis of perchlorate, thiocyanate, nitrate and iodide in human amniotic fluid using ion chromatography and electrospray tandem mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Blount, Benjamin C. [Division of Laboratory Sciences, National Center for Environmental Health, Centers for Disease Control and Prevention, Atlanta, GA 30341 (United States)]. E-mail: bblount@cdc.gov; Valentin-Blasini, Liza [Division of Laboratory Sciences, National Center for Environmental Health, Centers for Disease Control and Prevention, Atlanta, GA 30341 (United States)

    2006-05-10

    Because of health concerns surrounding in utero exposure to perchlorate, we developed a sensitive and selective method for quantifying iodide, as well as perchlorate and other sodium-iodide symporter (NIS) inhibitors in human amniotic fluid using ion chromatography coupled with electrospray ionization tandem mass spectrometry. Iodide and NIS inhibitors were quantified using a stable isotope-labeled internal standards (Cl{sup 18}O{sub 4} {sup -}, S{sup 13}CN{sup -} and {sup 15}NO{sub 3} {sup -} with excellent assay accuracy of 100%, 98%, 99%, 95% for perchlorate, thiocyanate, nitrate and iodide, respectively, in triplicate analysis of spiked amniotic fluid sample). Excellent analytical precision (<5.2% RSD for all analytes) was found when amniotic fluid quality control pools were repetitively analyzed for iodide and NIS-inhibitors. Selective chromatography and tandem mass spectrometry reduced the need for sample cleanup, resulting in a rugged and rapid method capable of routinely analyzing 75 samples/day. Analytical response was linear across the physiologically relevant concentration range for the analytes. Analysis of a set of 48 amniotic fluid samples identified the range and median levels for perchlorate (0.057-0.71, 0.18 {mu}g/L), thiocyanate (<10-5860, 89 {mu}g/L), nitrate (650-8900, 1620 {mu}g/L) and iodide (1.7-170, 8.1 {mu}g/L). This selective, sensitive, and rapid method will help assess exposure of the developing fetus to low levels of NIS-inhibitors and their potential to inhibit thyroid function.

  15. Formation of organic iodine supplied as iodide in a soil-water system in Chiba, Japan.

    Science.gov (United States)

    Shimamoto, Yoko S; Takahashi, Yoshio; Terada, Yasuko

    2011-03-15

    Speciation of iodine in a soil-water system was investigated to understand the mechanism of iodine mobility in surface environments. Iodine speciation in soil and pore water was determined by K-edge XANES and HPLC-ICP-MS, respectively, for samples collected at a depth of 0-12 cm in the Yoro area, Chiba, Japan. Pore water collected at a 0-6 cm depth contained 50%-60% of organic iodine bound to dissolved organic matter, with the other portion being I(-). At a 9-12 cm depth, 98% of iodine was in the form of dissolved I(-). In contrast, XANES analysis revealed that iodine in soil exists as organic iodine at all depths. Iodine mapping of soil grains was obtained using micro-XRF analysis, which also indicated that iodine is bound to organic matter. The activity of laccase, which has the ability to oxidize I(-) to I(2), was high at the surface of the soil-water layer, suggesting that iodide oxidizing enzymes can promote iodine organification. The distribution coefficient of organic iodine in the soil-water system was more than 10-fold greater than that of iodide. Transformation of inorganic iodine to organic iodine plays an important role in iodine immobilization, especially in a surface soil-water system.

  16. Photocatalytic hydrogen generation from hydriodic acid using methylammonium lead iodide in dynamic equilibrium with aqueous solution

    Science.gov (United States)

    Park, Sunghak; Chang, Woo Je; Lee, Chan Woo; Park, Sangbaek; Ahn, Hyo-Yong; Nam, Ki Tae

    2017-01-01

    The solar-driven splitting of hydrohalic acids (HX) is an important and fast growing research direction for H2 production. In addition to the hydrogen, the resulting chemicals (X2/X3-) can be used to propagate a continuous process in a closed cycle and are themselves useful products. Here we present a strategy for photocatalytic hydrogen iodide (HI) splitting using methylammonium lead iodide (MAPbI3) in an effort to develop a cost-effective and easily scalable process. Considering that MAPbI3 is a water-soluble ionic compound, we exploit the dynamic equilibrium of the dissolution and precipitation of MAPbI3 in saturated aqueous solutions. The I- and H+ concentrations of the aqueous solution are determined to be the critical parameters for the stabilization of the tetragonal MAPbI3 phase. Stable and efficient H2 production under visible light irradiation was demonstrated. The solar HI splitting efficiency of MAPbI3 was 0.81% when using Pt as a cocatalyst.

  17. Inhibition of acid corrosion of steel by some S-alkylisothiouronium iodides

    Energy Technology Data Exchange (ETDEWEB)

    Arab, S.T.; Noor, E.A. (Girl' s Coll. of Education, Jeddah (Saudi Arabia))

    1993-02-01

    Five selected S-alkylisothisothiouronium iodides have been studied as acid corrosion inhibitors at 30 C for steel in 0.5 M H[sub 2]SO[sub 4] using gasometry, mass loss, and direct current (DC) polarization techniques. All of the data reveal that the compounds act as inhibitors in the acid environments; furthermore, polarization curves show that the compounds act as mixed-type inhibitors. It was found that the inhibition efficiency increases with the increase of the length of the additive alkyl chain. Langmuir's adsorption isotherms fit the experimental data for the studied compounds. Thermodynamic parameter were obtained from experimental data of the temperature studies of the inhibition process at five temperatures ranging from 30 to 70 C. It was observed that the activation energy is slightly increased with the increase of the additive alkyl chain. On the other hand, the sudden large increase of the inhibition behavior of S-hexylisothiouronium iodide was attributed to a different adsorption process.

  18. Sodium Iodide Symporter for Nuclear Molecular Imaging and Gene Therapy: From Bedside to Bench and Back

    Directory of Open Access Journals (Sweden)

    Byeong-Cheol Ahn

    2012-01-01

    Full Text Available Molecular imaging, defined as the visual representation, characterization and quantification of biological processes at the cellular and subcellular levels within intact living organisms, can be obtained by various imaging technologies, including nuclear imaging methods. Imaging of normal thyroid tissue and differentiated thyroid cancer, and treatment of thyroid cancer with radioiodine rely on the expression of the sodium iodide symporter (NIS in these cells. NIS is an intrinsic membrane protein with 13 transmembrane domains and it takes up iodide into the cytosol from the extracellular fluid. By transferring NIS function to various cells via gene transfer, the cells can be visualized with gamma or positron emitting radioisotopes such as Tc-99m, I-123, I-131, I-124 and F-18 tetrafluoroborate, which are accumulated by NIS. They can also be treated with beta- or alpha-emitting radionuclides, such as I-131, Re-186, Re-188 and At-211, which are also accumulated by NIS. This article demonstrates the diagnostic and therapeutic applications of NIS as a radionuclide-based reporter gene for trafficking cells and a therapeutic gene for treating cancers.

  19. Chitosan finishing nonwoven textiles loaded with silver and iodide for antibacterial wound dressing applications.

    Science.gov (United States)

    Aubert-Viard, François; Martin, Adeline; Chai, Feng; Neut, Christel; Tabary, Nicolas; Martel, Bernard; Blanchemain, Nicolas

    2015-03-02

    Polyethylene terephtalate (PET) and Polypropylene (PP) textiles are widely used in biomedical application such as wound dressings and implants. The aim of this work was to develop an antibacterial chitosan (CHT) coating activated by silver or by iodine. Chitosan was immobilized onto PET and PP supports using citric acid (CTR) as a crosslinking agent through a pad-dry-cure textile finishing process. Interestingly, depending on the CHT/CTR molar ratio, two different systems were obtained: rich in cationic ammonium groups when the CTR concentration was 1%w/v, and rich in anionic carboxylate groups when the CTR concentration was 10%w/v. As a consequence, such samples could be selectively loaded with iodine and silver nitrate, respectively.Both types of coatings were analyzed using SEM and FTIR, their sorption capacities were evaluated toward iodide/iodate anions (I(-)/IO3(-)) and the silver cations (Ag(+)) were evaluated using elemental analysis. Finally, in vitro evaluations were carried out to evaluate the cytocompatibility on the epithelial cell line. The silver loaded textile reported a stronger antibacterial effect against E.coli (5 log10 reduction) than toward S. aureus (3 log10) while the antibacterial effect of the iodide loaded textiles was limited to 1 log10 to 2 log10 on both strains.

  20. The effect of potassium iodide on the production of acid phosphatase by Sporothrix schenckii

    Directory of Open Access Journals (Sweden)

    P. S. Grover

    2003-06-01

    Full Text Available The present study was undertaken to find out the in vitro effect of potassium iodide (KI on the production of acid phosphatase by fully characterized strain of S.schenckii isolated from a patient of Cutaneous Sporotrichosis. The enzyme acid phosphatase was estimated during the 3 phases of growth of S.schenckii, without and with three concentrations of KI incorporated in the culture medium. In the control and in the test proper, with various concentrations of KI, no adverse effect of KI was observed on the production of acid phosphatase in early and mid log phase of fungal growth. Whereas in the exponential phase in test proper, there was a statistical significant decrease in the enzyme production with 0.8% and 3.2% of KI. The low activity at 0.8% and 3.2% KI indicates that KI has inhibitory effect on the growth of S.schenckii and has led to decrease in the activity of the enzyme. (Med J Indones 2003; 12: 65-8 Keywords: S.schenckii, acid phosphatase, potassium iodide

  1. Serum and tissue iodine concentrations in rats fed diets supplemented with kombu powder or potassium iodide.

    Science.gov (United States)

    Yoshida, Munehiro; Mukama, Ayumi; Hosomi, Ryota; Fukunaga, Kenji; Nishiyama, Toshimasa

    2014-01-01

    Serum and tissue iodine concentration was measured in rats fed a diet supplemented with powdered kombu (Saccharina sculpera) or potassium iodide to evaluate the absorption of iodine from kombu. Eighteen male 5-wk-old Wistar rats were divided into three groups and fed a basal AIN93G diet (iodine content, 0.2 mg/kg) or the basal diet supplemented with iodine (183 mg/kg) either in the form of kombu powder or potassium iodine (KI) for 4 wk. There were no differences in weight gain or serum biochemistry tests (alanine aminotransferase and aspartate aminotransferase activity, and total serum cholesterol and triglyceride concentration) after iodine supplementation. In addition, serum levels of the thyroid hormones thyroxine and triiodothyronine, as well as thyroid-stimulating hormone, were not affected. On the other hand, serum and tissue (thyroid, liver and kidney) iodine concentrations were markedly elevated after iodine supplementation. There was no difference in thyroid iodine concentration between KI and kombu supplementation. However, there was a significant difference observed in the iodine concentrations of serum, liver and kidney between the two iodine sources; rats fed KI had iodine concentrations in these tissues 1.8 to 1.9 times higher than those in rats fed kombu powder. These results suggest that the absorption of iodine from kombu is reduced compared to that from potassium iodide.

  2. Toxicity of tetramethylammonium hydroxide to aquatic organisms and its synergistic action with potassium iodide.

    Science.gov (United States)

    Mori, Izumi C; Arias-Barreiro, Carlos R; Koutsaftis, Apostolos; Ogo, Atsushi; Kawano, Tomonori; Yoshizuka, Kazuharu; Inayat-Hussain, Salmaan H; Aoyama, Isao

    2015-02-01

    The aquatic ecotoxicity of chemicals involved in the manufacturing process of thin film transistor liquid crystal displays was assessed with a battery of four selected acute toxicity bioassays. We focused on tetramethylammonium hydroxide (TMAH, CAS No. 75-59-2), a widely utilized etchant. The toxicity of TMAH was low when tested in the 72 h-algal growth inhibition test (Pseudokirchneriellia subcapitata, EC50=360 mg L(-1)) and the Microtox® test (Vibrio fischeri, IC50=6.4 g L(-1)). In contrast, the 24h-microcrustacean immobilization and the 96 h-fish mortality tests showed relatively higher toxicity (Daphnia magna, EC50=32 mg L(-1) and Oryzias latipes, LC50=154 mg L(-1)). Isobologram and mixture toxicity index analyses revealed apparent synergism of the mixture of TMAH and potassium iodide when examined with the D. magna immobilization test. The synergistic action was unique to iodide over other halide salts i.e. fluoride, chloride and bromide. Quaternary ammonium ions with longer alkyl chains such as tetraethylammonium and tetrabutylammonium were more toxic than TMAH in the D. magna immobilization test.

  3. Iodine in raw and pasteurized milk of dairy cows fed different amounts of potassium iodide.

    Science.gov (United States)

    Norouzian, M A

    2011-02-01

    Relation between iodine (I) intake by lactating Holstein cows and iodine concentrations in raw and pasteurized milk were investigated. Four treatment groups with eight cows assigned to each treatment were fed a basal diet containing 0.534 mg I/kg alone or supplemented with potassium iodide at 2.5, 5 or 7.5 mg/kg in 7-week period. Iodine concentrations in raw milk increased with each increase in dietary I from 162.2 ng/ml for basal diet to 534.5, 559.8 and 607.5 ng/ml when 2.5, 5 and 7.5 mg/kg was fed as potassium iodide (P < 0.05). This trend was found for blood plasma and urine iodine concentration. Iodine supplementation had no significant effect on thyroidal hormones. high-temperature short-time (HTST) pasteurization process reduced I concentration. The mean iodine content found in the milk prior to heating processing was 466.0 ± 205.0 ng/ml, whereas for the processed milk this level was 349.5 ± 172.8 ng/ml. It was concluded that iodine supplementation above of NRC recommendation (0.5 mg/kg diet DM) resulted in significant increases in iodine concentrations in milk, although the effect of heating in HTST pasteurization process on iodine concentration was not negligible.

  4. Characterization of thermally evaporated lead iodide films aimed for the detection of X-rays

    Energy Technology Data Exchange (ETDEWEB)

    Caldeira Filho, A.M. [Departamento de Fisica, Faculdade de Filosofia, Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo - USP, Avenida Bandeirantes 3900, 14040-901, Ribeirao Preto-SP (Brazil); Mulato, M., E-mail: mmulato@ffclrp.usp.b [Departamento de Fisica, Faculdade de Filosofia, Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo - USP, Avenida Bandeirantes 3900, 14040-901, Ribeirao Preto-SP (Brazil)

    2011-04-21

    Some semiconductor materials such as lead iodide (PbI{sub 2}) have applications in the detection of ionizing radiation at room temperature using the direct detection method. In this work we investigate lead iodide films deposited by thermal evaporation. The morphology, structure, and electric properties were investigated as a function of deposition height, i.e. the distance between evaporation-boat and substrates. The results show a morphology of vertical leaves and X-ray diffraction shows just one preferential orientation along the direction 110. Energy dispersive spectroscopy reveals that the films are not stoichiometric, with excess iodine atoms. Electrical resistivity of about 10{sup 8} {Omega} cm was measured. This is smaller than for the bulk due to structural defects. The values of activation energy for electric transport increase from 0.52 up to 1.1 eV with decreasing deposition height, what indicates that the best film is the one deposited at the shortest distance. Exposure under X-ray mammographic energy shows a linear behavior up to 500 mR. No variation in sensibility was observed between 22 and 30 kVp.

  5. Administration of additional inactive iodide during radioiodine therapy for Graves' disease. Who might benefit?

    Energy Technology Data Exchange (ETDEWEB)

    Dietlein, M.; Moka, D.; Reinholz, U.; Schmidt, M.; Schomaecker, K.; Schicha, H.; Wellner, U. [Koeln Univ. (Germany). Dept. of Nuclear Medicine

    2007-07-01

    Aim: Graves' hyperthyroidism and antithyroid drugs empty the intrathyroid stores of hormones and iodine. The consequence is rapid {sup 131}I turnover and impending failure of radioiodine therapy. Can administration of additional inactive iodide improve 131I kinetics? Patients, methods: Fifteen consecutive patients, in whom the 48 h post-therapeutically calculated thyroid dose was between 150 and 249 Gy due to an unexpectedly short half-life, received 3 x 200 {mu}g inactive potassium-iodide ({sup 127}I) daily for 3 days (Group A), while 17 consecutive patients with a thyroid dose of = 250 Gy (Group B) served as the non-iodide group. 48 hours after {sup 131}I administration (M1) and 4 or 5 days later (M2) the following parameters were compared: effective {sup 131}I half-life, thyroid dose, total T3, total T4, {sup 131}I-activity in the T3- and T4-RIAs. Results: In Group A, the effective {sup 131}I half-life M1 before iodine (3.81 {+-} 0.93 days) was significantly (p <0.01) shorter than the effective {sup 131}I half-life M2 (4.65 {+-} 0.79 days). Effective {sup 131}I half-life M1 correlated with the benefit from inactive {sup 127}I (r = -0.79): Administration of {sup 127}I was beneficial in patients with an effective {sup 131}I half-life M1 of <3 or 4 days. Patients from Group A with high initial specific {sup 131}I activity of T3 and T4 showed lower specific {sup 131}I activity after addition of inactive iodine compared with patients from the same group with a lower initial specific {sup 131}I activity of T3 and T4 and compared with the patient group B who was given no additional inactive iodide. This correlation was mathematically described and reflected in the flatter gradient in Group A (y = 0.5195x + 0.8727 for {sup 131}I T3 and y = 1.0827x - 0.4444 for {sup 131}I T4) and steeper gradient for Group B (y = 0.6998x + 0.5417 for {sup 131}I T3 and y = 1.3191x - 0.2901 for {sup 131}I T4). Radioiodine therapy was successful in all 15 patients from Group A

  6. Replacement of monochromator and proportional gas counter by mercuric iodide detector in X-ray powder diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Nissenbaum, J.; Levi, A.; Burger, A.; Schieber, M. (Hebrew Univ., Jerusalem (Israel). School of Applied Science and Technology)

    1983-02-01

    Low resolution and therefore low-cost mercuric iodide detectors have successfully been applied to replace the combination of a graphite monochromator and a proportional gas radiation counter used in X-ray diffractometers. The mercuric iodide detector requires a lower DC bias of only 200 V rather than the 1500 V bias needed for the proportional gas counter. The much better stopping power of HgI/sub 2/ allows higher counting efficiency and therefore a better signal-to-noise ratio. Results are shown for X-ray powder diffractions of polycrystalline cubic silicon and tetragonal HgI/sub 2/.

  7. Inner Sphere and Outer Sphere Electron Transfer to Methyl Iodide. Deuterium and 13C Kinetic Isotope Effects

    DEFF Research Database (Denmark)

    Holm, Torkil; Crossland, Ingolf

    1996-01-01

    Deuterium and 13C kinetic isotope effects (KIEs) have been determined for the conversion of methyl iodide into methyl radical via inner sphere ET (electron transfer) and via outer sphere ET. The alfa-deuterium KIE was found to be very high for in......Deuterium and 13C kinetic isotope effects (KIEs) have been determined for the conversion of methyl iodide into methyl radical via inner sphere ET (electron transfer) and via outer sphere ET. The alfa-deuterium KIE was found to be very high for in...

  8. Constraining the sensitivity of iodide adduct chemical ionization mass spectrometry to multifunctional organic molecules using the collision limit and thermodynamic stability of iodide ion adducts

    Science.gov (United States)

    Lopez-Hilfiker, Felipe D.; Iyer, Siddarth; Mohr, Claudia; Lee, Ben H.; D'Ambro, Emma L.; Kurtén, Theo; Thornton, Joel A.

    2016-04-01

    The sensitivity of a chemical ionization mass spectrometer (ions formed per number density of analytes) is fundamentally limited by the collision frequency between reagent ions and analytes, known as the collision limit, the ion-molecule reaction time, and the transmission efficiency of product ions to the detector. We use the response of a time-of-flight chemical ionization mass spectrometer (ToF-CIMS) to N2O5, known to react with iodide at the collision limit, to constrain the combined effects of ion-molecule reaction time, which is strongly influenced by mixing and ion losses in the ion-molecule reaction drift tube. A mass spectrometric voltage scanning procedure elucidates the relative binding energies of the ion adducts, which influence the transmission efficiency of molecular ions through the electric fields within the vacuum chamber. Together, this information provides a critical constraint on the sensitivity of a ToF-CIMS towards a wide suite of routinely detected multifunctional organic molecules for which no calibration standards exist. We describe the scanning procedure and collision limit determination, and we show results from the application of these constraints to the measurement of organic aerosol composition at two different field locations.

  9. Iodide Impurities in Hexadecyltrimethylammonium Bromide (CTAB) Products: Lot−Lot Variations and Influence on Gold Nanorod Synthesis

    NARCIS (Netherlands)

    Rayavarapu, Raja Gopal; Ungureanu, Constantin; Krystec, Petra; Leeuwen, van Ton G.; Manohar, Srirang

    2010-01-01

    Recent reports [Smith and Korgel Langmuir 2008, 24, 644−649 and Smith et al.Langmuir 2009, 25, 9518−9524] have implicated certain hexadecyltrimethylammonium bromide (CTAB) products with iodide impurities, in the failure of a seed-mediated, silver and surfactant-assisted growth protocol, to produce g

  10. Evaluation of iodide deficiency in the lactating rat and pup using a biologically based dose response (BBDR) Model***

    Science.gov (United States)

    A biologically-based dose response (BBDR) model for the hypothalamic-pituitary thyroid (HPT) axis in the lactating rat and nursing pup was developed to describe the perturbations caused by iodide deficiency on the 1-IPT axis. Model calibrations, carried out by adjusting key model...

  11. Evaluation of iodide deficiency in the lactating rat and pup using a biologically based dose-response model

    Science.gov (United States)

    A biologically-based dose response (BBDR) model for the hypothalamic-pituitary thyroid (BPT) axis in the lactating rat and nursing pup was developed to describe the perturbations caused by iodide deficiency on the HPT axis. Model calibrations, carried out by adjusting key model p...

  12. Congenital Hypothyroidism Caused by a PAX8 Gene Mutation Manifested as Sodium/Iodide Symporter Gene Defect

    Directory of Open Access Journals (Sweden)

    Wakako Jo

    2010-01-01

    Full Text Available Loss-of-function mutations of the PAX8 gene are considered to mainly cause congenital hypothyroidism (CH due to thyroid hypoplasia. However, some patients with PAX8 mutation have demonstrated a normal-sized thyroid gland. Here we report a CH patient caused by a PAX8 mutation, which manifested as iodide transport defect (ITD. Hypothyroidism was detected by neonatal screening and L-thyroxine replacement was started immediately. Although 123I scintigraphy at 5 years of age showed that the thyroid gland was in the normal position and of small size, his iodide trapping was low. The ratio of the saliva/plasma radioactive iodide was low. He did not have goiter; however laboratory findings suggested that he had partial ITD. Gene analyses showed that the sodium/iodide symporter (NIS gene was normal; instead, a mutation in the PAX8 gene causing R31H substitution was identified. The present report demonstrates that individuals with defective PAX8 can have partial ITD, and thus genetic analysis is useful for differential diagnosis.

  13. N,N-Dimethylbenzimidazolium iodide as a green catalyst for cross-coupling of aromatic aldehydeswith unactivated imines

    Directory of Open Access Journals (Sweden)

    Viwat Hahnvajana wong

    2016-03-01

    Full Text Available Cross-coupling of aromatic aldehydes with unactivated iminescatalyzed by N,N-dimethylbenzimidazolium iodide in ethanolic sodium hydroxide solution gave α-amino ketonesin satisfactory yields. Benzoin condensation and further oxidation of the resulted aroins also occurred as side reactions.

  14. Efficient Method for the Determination of the Activation Energy of the Iodide-Catalyzed Decomposition of Hydrogen Peroxide

    Science.gov (United States)

    Sweeney, William; Lee, James; Abid, Nauman; DeMeo, Stephen

    2014-01-01

    An experiment is described that determines the activation energy (E[subscript a]) of the iodide-catalyzed decomposition reaction of hydrogen peroxide in a much more efficient manner than previously reported in the literature. Hydrogen peroxide, spontaneously or with a catalyst, decomposes to oxygen and water. Because the decomposition reaction is…

  15. The antimicrobial effect of apical box versus apical cone preparation using iodine potassium iodide as root canal dressing

    DEFF Research Database (Denmark)

    Markvart, Merete; Dahlén, Gunnar; Reit, Claes-Erik

    2013-01-01

    OCl (12 ml). Lastly, the canals were filled with 17% EDTA (2 × 30 s) and 5% iodine potassium iodide (IKI) for 10 min. The canals were sampled for micro-organisms on four occasions: before instrumentation, after instrumentation, after application of IKI dressing and at the beginning of the second...

  16. Selective copper(II acetate and potassium iodide catalyzed oxidation of aminals to dihydroquinazoline and quinazolinone alkaloids

    Directory of Open Access Journals (Sweden)

    Matthew T. Richers

    2013-06-01

    Full Text Available Copper(II acetate/acetic acid/O2 and potassium iodide/tert-butylhydroperoxide systems are shown to affect the selective oxidation of ring-fused aminals to dihydroquinazolines and quinazolinones, respectively. These methods enable the facile preparation of a number of quinazoline alkaloid natural products and their analogues.

  17. Potassium iodide catalyzed simultaneous C3-formylation and N-aminomethylation of indoles with 4-substituted-N,N-dimethylanilines.

    Science.gov (United States)

    Li, Lan-Tao; Li, Hong-Ying; Xing, Li-Juan; Wen, Li-Juan; Wang, Peng; Wang, Bin

    2012-12-28

    A one-pot dual functionalization of indoles has been developed. The simultaneous C3-formylation and N-aminomethylation of indoles can be achieved using readily available potassium iodide as a catalyst and tert-butyl peroxybenzoate as a co-oxidant.

  18. The lactoperoxidase system : the influence of iodide and the chemical and antimicrobial stability over the period of about 18 months

    NARCIS (Netherlands)

    Bosch, EH; Van Doorne, H; De Vries, S

    2000-01-01

    The lactoperoxidase (LP) system is a natural antimicrobial system, the use of which has been suggested as a preservative in foods and pharmaceuticals. The effect of adding iodide to the LP system, the chemical stability and the change in antimicrobial effectiveness during storage was studied. Additi

  19. Determination of iodide by volumetric titration in support of the oil eletrolabeling with {sup 123}I

    Energy Technology Data Exchange (ETDEWEB)

    Kenup-Cantuaria, Hericka O.H.; Brandao, Luis E.B., E-mail: hkenup@ien.gov.br, E-mail: brandao@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Silva, Ademir X., E-mail: ademir@nuclear.ufrj.br [Coordenacao dos Programas de Pos-Graduacao em Engenharia (PEN/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear

    2015-07-01

    The accuracy in measuring flow rate in pipelines is essential task to control various technical parameters in an industrial plant in oil industry and its derivatives. For this reason, it becomes increasingly widespread the uses of organic molecules labeled with radioactive isotopes mainly because of the wide possibility in use of different radioisotopes also due to the new labeling techniques. This paper presents a study to develop an electrochemical technique for oil labeling with iodine -123 and to determine the yield of production by measuring the concentration of iodide (I{sup -}) during this process. The volumetric titration technique was applied as a basis for quantitative and qualitative measures to monitor the labeling process. The results indicate the technical proposal as a viable alternative for monitoring electro labeling process of lubricating oils with iodine -123. (author)

  20. Electron and Hole Drift Mobility Measurements on Methylammonium Lead Iodide Perovskite Solar Cells

    Energy Technology Data Exchange (ETDEWEB)

    Maynard, Brian; Long, Qi; Schiff, Eric A.; Yang, Mengjin; Zhu, Kai; Kottokkaran, Ranjith; Abbas, Hisham; Dalal, Vikram L.

    2016-04-25

    We report nanosecond domain time-of-flight measurements of electron and hole photocarriers in methylammonium lead iodide perovskite solar cells. The mobilities ranged from 0.06 to 1.4 cm2/Vs at room temperature, but there is little systematic difference between the two carriers. We also find that the drift mobilities are dispersive (time-dependent). The dispersion parameters are in the range of 0.4-0.7, and they imply that terahertz domain mobilities will be much larger than nanosecond domain mobilities. The temperature-dependences of the dispersion parameters are consistent with confinement of electron and hole transport to fractal-like spatial networks within nanoseconds of their photogeneration.

  1. Role of -methyl-8-(alkoxy)quinolinium iodide in suppression of protein-protein interactions

    Indian Academy of Sciences (India)

    Bimlesh Ojha; Cirantan Kar; Gopal Das

    2013-03-01

    There is a great deal of interest in developing small molecule inhibitors of protein misfolding and aggregation due to a growing number of pathologic states known as amyloid disorders. In searching for alternative ways to reduce protein-protein interactions or to inhibit the amyloid formation, the inhibitory effects of cationic amphiphile viz. -methyl-8-(alkoxy)quinolinium iodide on aggregation behaviour of hen egg white lysozyme (HEWL) at alkaline pH has been studied. Even though the compounds did not protect native HEWL from conformational changes, they were effective in diminishing HEWL amyloid formation, delaying both nucleation and elongation phases. It is likely that strong binding in the HEWL compound complex, raises the activation energy barrier for protein misfolding and subsequent aggregation, thereby retarding the aggregation kinetics substantially.

  2. Tuning the band gap in hybrid tin iodide perovskite semiconductors using structural templating.

    Science.gov (United States)

    Knutson, Jeremy L; Martin, James D; Mitzi, David B

    2005-06-27

    Structural distortions within the extensive family of organic/inorganic hybrid tin iodide perovskite semiconductors are correlated with their experimental exciton energies and calculated band gaps. The extent of the in- and out-of-plane angular distortion of the SnI4(2-) perovskite sheets is largely determined by the relative charge density and steric requirements of the organic cations. Variation of the in-plane Sn-I-Sn bond angle was demonstrated to have the greatest impact on the tuning of the band gap, and the equatorial Sn-I bond distances have a significant secondary influence. Extended Hückel tight-binding band calculations are employed to decipher the crystal orbital origins of the structural effects that fine-tune the band structure. The calculations suggest that it may be possible to tune the band gap by as much as 1 eV using the templating influence of the organic cation.

  3. Reactivity of Ozone with Solid Potassium Iodide Investigated by Atomic Force Microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Mulleregan, Alice; Brown, Matthew A.; Ashby, Paul D.; Ogletree, D. Frank; Salmeron, Miquel; Hemminger, John C.

    2008-04-14

    The reaction of ozone with the (100) plane of solid potassium iodide (KI) was investigated using atomic force microscopy (AFM). The reaction forming potassium iodate (KIO{sub 3}) initiates at step edges prior to reacting on the flat terraces. Small domains of KIO{sub 3}, initially 3.8 {angstrom} in height are formed on the top of step edges. Following reaction at the step edge, domains of KIO{sub 3} are formed across the terraces. With prolonged exposure to ozone, KIO{sub 3} domains nucleate further growth until the surface is evenly covered with KIO{sub 3} particles that are 4-6 nm in height, at which point the surface is passivated and the reaction terminates.

  4. A review of recent measurements of optical and thermal properties of. alpha. -mercuric iodide

    Energy Technology Data Exchange (ETDEWEB)

    Burger, A.; Morgan, S.H.; Silberman, E. (Fisk Univ., Nashville, TN (United States). Dept. of Physics); Nason, D.; Cheng, A.Y. (EG and G Energy Measurements, Inc., Goleta, CA (United States). Santa Barbara Operations)

    1991-01-01

    The knowledge of the physical properties of a crystal and their relation to the nature and content of defects are essential for both applications and fundamental reasons. Alpha-mercuric iodide ({alpha}-HgI{sub 2}) is a material which was found important applications as room temperature X-ray and gamma ray detectors. Some recent thermal and optical measurements of this material, using the samples of improved crystallinity which are now available, are reviewed below. Heretofore, these properties have received less attention than the mechanical and electrical properties, particularly at elevated temperatures. In the technology of {alpha}-HgI{sub 2} where there is a continuing motivation to obtain larger single crystals without compromising the material quality, a better knowledge of the thermal and optical properties may lead to improvements in the processes of material purification, crystal growth and device fabrication.

  5. Understanding charge transport in lead iodide perovskite thin-film field-effect transistors

    Science.gov (United States)

    Senanayak, Satyaprasad P.; Yang, Bingyan; Thomas, Tudor H.; Giesbrecht, Nadja; Huang, Wenchao; Gann, Eliot; Nair, Bhaskaran; Goedel, Karl; Guha, Suchi; Moya, Xavier; McNeill, Christopher R.; Docampo, Pablo; Sadhanala, Aditya; Friend, Richard H.; Sirringhaus, Henning

    2017-01-01

    Fundamental understanding of the charge transport physics of hybrid lead halide perovskite semiconductors is important for advancing their use in high-performance optoelectronics. We use field-effect transistors (FETs) to probe the charge transport mechanism in thin films of methylammonium lead iodide (MAPbI3). We show that through optimization of thin-film microstructure and source-drain contact modifications, it is possible to significantly minimize instability and hysteresis in FET characteristics and demonstrate an electron field-effect mobility (μFET) of 0.5 cm2/Vs at room temperature. Temperature-dependent transport studies revealed a negative coefficient of mobility with three different temperature regimes. On the basis of electrical and spectroscopic studies, we attribute the three different regimes to transport limited by ion migration due to point defects associated with grain boundaries, polarization disorder of the MA+ cations, and thermal vibrations of the lead halide inorganic cages. PMID:28138550

  6. Use of mercuric iodide X-ray detectors with alpha backscattering spectrometers for space applications

    Science.gov (United States)

    Iwanczyk, J. S.; Wang, Y. J.; Dorri, N.; Dabrowski, A. J.; Economou, T. E.

    1991-01-01

    The authors present X-ray fluorescence (XRF) spectra of different extraterrestrial samples taken with a mercuric iodide (HgI2) spectrometer inserted into an alpha backscattering instrument identical to that used in the Soviet Phobos mission. The results obtained with the HgI2 ambient temperature detector are compared with those obtained using an Si(Li) cryogenically cooled detector. Efforts to design an optimized instrument for space application are also described. The results presented indicate that the energy resolution and sensitivity of HgI2 detectors are adequate to meet the performance needs of a number of proposed space applications, particularly those in which cooled silicon X-ray detectors are impractical or even not usable, such as for the target science programs on geoscience opportunities for lunar surface, Mars surface, and other comet and planetary missions being planned by NASA and ESA.

  7. Photoemission and optical constant measurements of Cesium Iodide thin film photocathode

    CERN Document Server

    Triloki,; Gupta, Nikita; Jammal, Nabeel F A; Singh, B K

    2014-01-01

    Performance of cesium iodide (CsI) as a reflective photocathode is presented. Absolute quantum efficiency (QE) measurement of 500 nm thick CsI film has been carried out in the wavelength range of 150 nm to 200 nm. Optical absorbance of 500 nm thick CsI film in the spectral range of 190 nm to 900 nm is analyzed and optical energy band gap is calculated using Tauc plot. To see the dispersive behavior of CsI film, refractive index has been determined by envelop plot of transmittance data, using Swanepoel method. Additional information on morphological and elemental composition results of CsI film, gained by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS), respectively are also reported in present work.

  8. Reentrant Structural and Optical Properties and Large Positive Thermal Expansion in Perovskite Formamidinium Lead Iodide.

    Science.gov (United States)

    Fabini, Douglas H; Stoumpos, Constantinos C; Laurita, Geneva; Kaltzoglou, Andreas; Kontos, Athanassios G; Falaras, Polycarpos; Kanatzidis, Mercouri G; Seshadri, Ram

    2016-12-05

    The structure of the hybrid perovskite HC(NH2 )2 PbI3 (formamidinium lead iodide) reflects competing interactions associated with molecular motion, hydrogen bonding tendencies, thermally activated soft octahedral rotations, and the propensity for the Pb(2+) lone pair to express its stereochemistry. High-resolution synchrotron X-ray powder diffraction reveals a continuous transition from the cubic α-phase (Pm3‾ m, #221) to a tetragonal β-phase (P4/mbm, #127) at around 285 K, followed by a first-order transition to a tetragonal γ-phase (retaining P4/mbm, #127) at 140 K. An unusual reentrant pseudosymmetry in the β-to-γ phase transition is seen that is also reflected in the photoluminescence. Around room temperature, the coefficient of volumetric thermal expansion is among the largest for any extended crystalline solid.

  9. The Inhibition Effect of Potassium Iodide on the Corrosion of Pure Iron in Sulphuric Acid

    Directory of Open Access Journals (Sweden)

    Tarik Attar

    2014-01-01

    Full Text Available The use of inorganic inhibitors as an alternative to organic compounds is based on the possibility of degradation of organic compounds with time and temperature. The inhibition effect of potassium iodide on the corrosion of pure iron in 0.5 M H2SO4 has been studied by weight loss. It has been observed from the results that the inhibition efficiency (IE% of KI increases from 82.17% to 97.51% with the increase in inhibitor concentration from 1·10−4 to 2·10−3 M. The apparent activation energy (Ea and the equilibrium constant of adsorption (Kads were calculated. The adsorption of the inhibitor on the pure iron surface is in agreement with Langmuir adsorption isotherm.

  10. Grain-Size-Limited Mobility in Methylammonium Lead Iodide Perovskite Thin Films

    Energy Technology Data Exchange (ETDEWEB)

    Reid, Obadiah G.; Yang, Mengjin; Kopidakis, Nikos; Zhu, Kai; Rumbles, Garry

    2016-09-09

    We report a systematic study of the gigahertz-frequency charge carrier mobility found in methylammonium lead iodide perovskite films as a function of average grain size using time-resolved microwave conductivity and a single processing chemistry. Our measurements are in good agreement with the Kubo formula for the AC mobility of charges confined within finite grains, suggesting (1) that the surface grains imaged via scanning electron microscopy are representative of the true electronic domain size and not substantially subdivided by twinning or other defects not visible by microscopy and (2) that the time scale of diffusive transport across grain boundaries is much slower than the period of the microwave field in this measurement (-100 ps). The intrinsic (infinite grain size) minimum mobility extracted form the model is 29 +/- 6 cm2 V-1 s-1 at the probe frequency (8.9 GHz).

  11. A coupled chemical burster: The chlorine dioxide-iodide reaction in two flow reactors

    Science.gov (United States)

    Dolnik, Milos; Epstein, Irving R.

    1993-01-01

    The dynamical behavior of the chlorine dioxide-iodide reaction has been studied in a system consisting of two continuous flow stirred tank reactors (CSTRs). The reactors are coupled by computer monitoring of the electrochemical potential in each reactor, which is then used to control the input into the other reactor. Two forms of coupling are employed: reciprocally triggered, exponentially decreasing stimulation, and alternating mass exchange. The reaction, which exhibits oscillatory and excitable behavior in a single CSTR, displays neuronlike bursting behavior with both forms of coupling. Reciprocal stimulation yields bursting in both reactors, while with alternating mass exchange, bursting is observed in one reactor and complex oscillation in the other. A simple model of the reaction gives good agreement between the experimental observations and numerical simulations.

  12. Cesium-iodide-based nanocrystal for the detection of ionizing radiation

    Science.gov (United States)

    Farzaneh, Azadeh; Abdi, Mohammad Reza; Saraee, Khadijeh Rezaee Ebrahim; Mostajaboddavati, Mojtaba; Quaranta, A.

    2016-05-01

    We report on the synthesis of cesium-iodide nanoparticles using sol-gel technique. The structural properties of CsI nanoparticles were characterized by X-ray diffraction and optical properties were followed by optical absorption and UV-vis fluorescence. Intense photoluminescence is also observed, with some spectral tuning possible with ripening time getting a range of emission photon wavelength approximately from 366 to 350 nm. The size effect on CsI luminescence leads to an increase in scintillation light yield, a redshift of the emission bands of the on_center and off_center self_trapped excitons (STEs) and an increase in the contribution of the off_center STEs to the net intrinsic emission yield. The energy transfer from the matrix to CsI nanoparticles is a key characteristic for scintillation detectors. So the scintillation spectra and decay curve to alpha particles of sample were monitored.

  13. Diphenyleneiodonium, an inhibitor of NOXes and DUOXes, is also an iodide-specific transporter

    Directory of Open Access Journals (Sweden)

    C. Massart

    2014-01-01

    Full Text Available NADPH oxidases (NOXes and dual oxidases (DUOXes generate O2.− and H2O2. Diphenyleneiodonium (DPI inhibits the activity of these enzymes and is often used as a specific inhibitor. It is shown here that DPI, at concentrations similar to those which inhibit the generation of O2 derivatives, activated the efflux of radioiodide but not of its analog 99mTcO4− nor of the K+ cation mimic 86Rb+ in thyroid cells, in the PCCl3 rat thyroid cell line and in COS cell lines expressing the iodide transporter NIS. Effects obtained with DPI, especially in thyroid cells, should therefore be interpreted with caution.

  14. Efficient organic solar cells using copper(I) iodide (CuI) hole transport layers

    Science.gov (United States)

    Peng, Ying; Yaacobi-Gross, Nir; Perumal, Ajay K.; Faber, Hendrik A.; Vourlias, George; Patsalas, Panos A.; Bradley, Donal D. C.; He, Zhiqun; Anthopoulos, Thomas D.

    2015-06-01

    We report the fabrication of high power conversion efficiency (PCE) polymer/fullerene bulk heterojunction (BHJ) photovoltaic cells using solution-processed Copper (I) Iodide (CuI) as hole transport layer (HTL). Our devices exhibit a PCE value of ˜5.5% which is equivalent to that obtained for control devices based on the commonly used conductive polymer poly(3,4-ethylenedioxythiophene): polystyrenesulfonate as HTL. Inverted cells with PCE >3% were also demonstrated using solution-processed metal oxide electron transport layers, with a CuI HTL evaporated on top of the BHJ. The high optical transparency and suitable energetics of CuI make it attractive for application in a range of inexpensive large-area optoelectronic devices.

  15. Interference of aging media on the assessment of yeast chronological life span by propidium iodide staining.

    Science.gov (United States)

    Pereira, Clara; Saraiva, Lucília

    2013-01-01

    An increasing number of researchers are using the Saccharomyces cerevisiae chronological aging model to gain insight into the post-mitotic cellular aging. Recently, an alternative approach to the traditional cellular viability assay by colony-forming unit (CFU) counts, based on the propidium iodide (PI) staining combined with flow cytometry (PI-FCM), was proposed for the assessment of yeast chronological aging. Since the chronological aging assessment shows variations particularly concerning the aging media, in this work, the influence of the most common aging media (exhausted media or water) on the assessment of chronological aging by PI staining was studied. Our results show that this methodology is highly affected by the aging media. Indeed, a correlation between CFU counts and the percentage of PI-stained cells is only achieved with the exhausted media. As such, the assessment of yeast chronological aging by PI-FCM water should not be used.

  16. Top and bottom surfaces limit carrier lifetime in lead iodide perovskite films

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Ye; Yang, Mengjin; Moore, David T.; Yan, Yong; Miller, Elisa M.; Zhu, Kai; Beard, Matthew C.

    2017-01-23

    Carrier recombination at defects is detrimental to the performance of solar energy conversion systems, including solar cells and photoelectrochemical devices. Point defects are localized within the bulk crystal while extended defects occur at surfaces and grain boundaries. If not properly managed, surfaces can be a large source of carrier recombination. Separating surface carrier dynamics from bulk and/or grain-boundary recombination in thin films is challenging. Here, we employ transient reflection spectroscopy to measure the surface carrier dynamics in methylammonium lead iodide perovskite polycrystalline films. We find that surface recombination limits the total carrier lifetime in perovskite polycrystalline thin films, meaning that recombination inside grains and/or at grain boundaries is less important than top and bottom surface recombination. The surface recombination velocity in polycrystalline films is nearly an order of magnitude smaller than that in single crystals, possibly due to unintended surface passivation of the films during synthesis.

  17. Diffusional analysis of the adsorption of methyl iodide on silver exchanged mordenite

    Energy Technology Data Exchange (ETDEWEB)

    Jubin, R.T. [Oak Ridge National Lab., TN (United States); Counce, R.M. [Univ. of Tennessee, Knoxville, TN (United States)

    1997-08-01

    The removal of organic iodides from off-gas streams is an important step in controlling the release of radioactive iodine to the environment during the treatment of radioactive wastes or the processing of some irradiated materials. Nine-well accepted mass transfer models were evaluated for their ability to adequately explain the observed CH{sub 3}I uptake behavior onto the Ag{degrees}Z. Linear and multidimensional regression techniques were used to estimate the diffusion constants and other model parameters, which then permitted the selection of an appropriate mass transfer model. Although a number of studies have been conducted to evaluate the loading of both elemental and methyl iodide on silver-exchanged mordenite, these studies focused primarily on the macro scale (deep bed) while evaluating the material under a broad range of process conditions and contaminants for total bed loading at the time of breakthrough. A few studies evaluated equilibrium or maximum loading. Thus, to date, only bulk loading data exist for the adsorption of CH{sub 3}I onto Ag{degrees}Z. Hence this is believed to be the first study to quantify the controlling mass transfer mechanisms of this process, It can be concluded from the analysis of the experimental data obtained by the {open_quotes}single-pellet{close_quotes} type experiments and for the process conditions used in this study that the overall mass transfer rate associated with the adsorption of CH{sub 3}I onto Ag{degrees}Z is affected by both micropore and macropore diffusion. The macropore diffusion rate was significantly faster than the micropore diffusion, resulting in a two-step adsorption behavior which was adequately modeled by a bimodal pore distribution model. The micropore diffusivity was determined to be on the order of 2 x 10{sup -14} cm{sup 2}/s. The system was also shown to be isothermal under all conditions of this study. 21 refs., 6 figs., 8 tabs.

  18. Intercalation of Layered Silicates, Layered Double Hydroxides, and Lead Iodide: Synthesis, Characterization and Properties.

    Science.gov (United States)

    Mehrotra, Vivek

    Layered silicates, layered double hydroxides, and lead iodide are lamellar solids that can incorporate guest species into the galleries between their layers. Various intercalated forms of these layered materials have been synthesized and their properties studied. The dielectric behavior of pristine fluorohectorite, a typical layered silicate, and Zn-Al layered double hydroxide is explained by considering the structural ordering and mobility of the intercalated water molecules, as well as models invoking fractal time processes and fractal structure. Intercalative polymerization of aniline and pyrrole into fluorohectorite leads to a multilayered structure consisting of single polymer chains alternately stacked with the 9.6 A thick silicate layers. The polymer chains are confined to the quasi two-dimensional interlayer space between the rigid host layers. The hybrid films exhibit highly anisotropic properties. The optical, electrical and mechanical behavior is discussed in terms of the molecular confinement of the polymer chains. Ethylenediamine functionalized C _{60} clusters have also been intercalated into fluorohectorite via an ion-exchange procedure. Intercalation results in an improved thermal stability of the functionalized C_{60} clusters. Rutherford backscattering spectrometry has been used to elucidate the mechanism of intercalative ion exchange of silver in muscovite mica, a layered silicate with a layer charge density of 2e per unit cell. It is proposed that ion-exchange progresses by intercalating successive galleries through the edges of the mica layers. Guest-host interactions have been studied in the system aniline-PbI_2. The optical and structural effects of aniline intercalation in lead iodide thin films is discussed. Intercalation leads to a large shift in the optical band gap of PbI_2. The observed change in band gap is not only due to the increased separation between the PbI_2 layers but also because of an electrostatic interaction between the

  19. Iodide substitution in lithium borohydride, LiBH{sub 4}-LiI

    Energy Technology Data Exchange (ETDEWEB)

    Rude, Line H., E-mail: line@inano.au.dk [Center for Materials Crystallography, Interdisciplinary Nanoscience Center and Department of Chemistry, Aarhus University, Langelandsgade 140, DK-8000 Aarhus C (Denmark); Groppo, Elena, E-mail: elena.groppo@unito.it [Dipartimento di Chimica I.F.M. and NIS, Universita di Torino, Torino (Italy); Arnbjerg, Lene M., E-mail: lenem@chem.au.dk [Center for Materials Crystallography, Interdisciplinary Nanoscience Center and Department of Chemistry, Aarhus University, Langelandsgade 140, DK-8000 Aarhus C (Denmark); Ravnsbaek, Dorthe B., E-mail: inadr@inano.au.dk [Center for Materials Crystallography, Interdisciplinary Nanoscience Center and Department of Chemistry, Aarhus University, Langelandsgade 140, DK-8000 Aarhus C (Denmark); Malmkjaer, Regitze A., E-mail: regitze.aagaard.malmkjaer@post.au.dk [Center for Materials Crystallography, Interdisciplinary Nanoscience Center and Department of Chemistry, Aarhus University, Langelandsgade 140, DK-8000 Aarhus C (Denmark); Filinchuk, Yaroslav, E-mail: Yaroslav.Filinchuk@uclouvain.be [Center for Materials Crystallography, Interdisciplinary Nanoscience Center and Department of Chemistry, Aarhus University, Langelandsgade 140, DK-8000 Aarhus C (Denmark); Swiss-Norwegian Beam Lines at ESRF, BP-220, 38043 Grenoble (France); Institute of Condensed Matter and Nanosciences, Universite Catholique de Louvain, Place L. Pasteur 1, B-1348 Louvain-la-Neuve (Belgium); Baricco, Marcello, E-mail: marcello.baricco@unito.it [Dipartimento di Chimica I.F.M. and NIS, Universita di Torino, Torino (Italy); Besenbacher, Flemming, E-mail: fbe@inano.au.dk [Interdisciplinary Nanoscience Center (iNANO) and Department of Physics and Astronomy, Aarhus University, DK-8000 Aarhus C (Denmark); Jensen, Torben R., E-mail: trj@chem.au.dk [Center for Materials Crystallography, Interdisciplinary Nanoscience Center and Department of Chemistry, Aarhus University, Langelandsgade 140, DK-8000 Aarhus C (Denmark)

    2011-08-18

    Graphical abstract: Highlights: > Anion substitution in LiBH{sub 4}. > Structure and properties of two LiBH{sub 4}-LiI solid solutions. > Stability upon heating and over time. > Hydrogen storage properties of LiBH{sub 4}-LiI. - Abstract: The new concept, anion substitution, is explored for possible improvement of hydrogen storage properties in the system LiBH{sub 4}-LiI. The structural chemistry and the substitution mechanism are analyzed using Rietveld refinement of in situ synchrotron radiation powder X-ray diffraction (SR-PXD) data, attenuated total reflectance infrared spectroscopy (ATR-IR), differential scanning calorimetry (DSC) and Sieverts measurements. Anion substitution is observed as formation of two solid solutions of Li(BH{sub 4}){sub 1-x}I{sub x}, which merge into one upon heating. The solid solutions have hexagonal structures (space group P6{sub 3}mc) similar to the structures of h-LiBH{sub 4} and {beta}-LiI. The solid solutions have iodide contents in the range {approx}0-62 mol% and are stable from below room temperature to the melting point at 330 deg. C. Thus the stability of the solid solutions is higher as compared to that of the orthorhombic and hexagonal polymorphs of LiBH{sub 4} and {alpha}- and {beta}-LiI. Furthermore, the rehydrogenation properties of the iodide substituted solid solution Li(BH{sub 4}){sub 1-x}I{sub x}, measured by the Sieverts method, are improved as compared to those of LiBH{sub 4}. After four cycles of hydrogen release and uptake the Li(BH{sub 4}){sub 1-x}I{sub x} solid solution maintains 68% of the calculated hydrogen storage capacity in contrast to LiBH{sub 4}, which maintains only 25% of the storage capacity after two cycles under identical conditions.

  20. Comparison of expressed human and mouse sodium/iodide sym-porters reveals differences in transport properties and subcellular localization

    Energy Technology Data Exchange (ETDEWEB)

    Dayem, M.; Basquin, C.; Navarro, V.; Carrier, P.; Marsault, R.; Lindenthal, S.; Pourcher, T. [Univ Nice Sophia Antipolis, Sch Med, CEA, DSV, iBEB, SBTN, TIRO, F-06107 Nice (France); Chang, P. [CNRS, UPMC Biol Dev, UMR 7009, F-06230 Villefranche Sur Mer (France); Huc, S.; Darrouzet, E. [CEA Valrho, DSV, iBEB, SBTN, F-30207 Bagnols Sur Ceze (France)

    2008-07-01

    The active transport of iodide from the blood stream into thyroid follicular cells is mediated by the Na{sup +}/I{sup -} sym-porter (NIS). We studied mouse NIS (mNIS) and found that it catalyzes iodide transport into transfected cells more efficiently than human NIS (hNIS). To further characterize this difference,we compared {sup 125}I, uptake in the transiently transfected human embryonic kidney (HEK) 293 cells. We found that the Vmax for mNIS was four times higher than that for hNIS, and that the iodide transport constant (Km) was 2-5-fold lower for hNIS than mNIS. We also performed immuno-cyto-localization studies and observed that the subcellular distribution of the two ortho-logs differed. While the mouse protein was predominantly found at the plasma membrane, its human ortho-log was intracellular in {approx} 40% of the expressing cells. Using cell surface protein-labeling assays, we found that the plasma membrane localization frequency of the mouse protein was only 2-5-fold higher than that of the human protein, and therefore cannot alone account for,x values. We reasoned that the difference in the obtained Vmax the observed difference could also be caused by a higher turnover number for iodide transport in the mouse protein. We then expressed and analyzed chimeric proteins. The data obtained with these constructs suggest that the iodide recognition site could be located in the region extending from the N-terminus to transmembrane domain 8, and that the region between transmembrane domain 5 and the C-terminus could play a role in the subcellular localization of the protein. (authors)

  1. Preparation and Luminous Characters of High Pure Thallium Iodide%高纯碘化铊的制备及其发光特性

    Institute of Scientific and Technical Information of China (English)

    杨桂林; 何华强

    2001-01-01

    High pure thallium iodide was made through the process of dissolving thallium in nitric acid, precipitating thallium ion by potassium iodide then subliming thallium iodide in vacuum. A series of spherical composite halides containing thallium iodide was made. Thallium iodide is used as green luminous material. It is also used as addition agent contained in composite halides of thallium iodide for different forms of application. Luminous characters of thallium iodide used as luminous material in metal halide lamps are presented.%以金属铊为原料,用硝酸溶解-碘化钾沉淀-真空升华的方法制备了高纯碘化铊,并且制备出多种球形碘化铊复合卤化物。碘化铊既可以单独用作绿光材料,也可以作为添加剂与其它金属卤化物复合得到复合金属卤化物发光材料,满足不同的使用要求。文章用图表介绍了碘化铊用作金属卤化物灯发光材料时的发光特性。

  2. Evaluation of perturbations in serum thyroid hormones during human pregnancy due to dietary iodide and perchlorate exposure using a biologically based dose-response model.

    Science.gov (United States)

    Lumen, Annie; Mattie, David R; Fisher, Jeffrey W

    2013-06-01

    A biologically based dose-response model (BBDR) for the hypothalamic pituitary thyroid (HPT) axis was developed in the near-term pregnant mother and fetus. This model was calibrated to predict serum levels of iodide, total thyroxine (T4), free thyroxine (fT4), and total triiodothyronine (T3) in the mother and fetus for a range of dietary iodide intake. The model was extended to describe perchlorate, an environmental and food contaminant, that competes with the sodium iodide symporter protein for thyroidal uptake of iodide. Using this mode-of-action framework, simulations were performed to determine the daily ingestion rates of perchlorate that would be associated with hypothyroxinemia or onset of hypothyroidism for varying iodide intake. Model simulations suggested that a maternal iodide intake of 75 to 250 µg/day and an environmentally relevant exposure of perchlorate (~0.1 µg/kg/day) did not result in hypothyroxinemia or hypothyroidism. For a daily iodide-sufficient intake of 200 µg/day, the dose of perchlorate required to reduce maternal fT4 levels to a hypothyroxinemic state was estimated at 32.2 µg/kg/day. As iodide intake was lowered to 75 µg/day, the model simulated daily perchlorate dose required to cause hypothyroxinemia was reduced by eightfold. Similarly, the perchlorate intake rates associated with the onset of subclinical hypothyroidism ranged from 54.8 to 21.5 µg/kg/day for daily iodide intake of 250-75 µg/day. This BBDR-HPT axis model for pregnancy provides an example of a novel public health assessment tool that may be expanded to address other endocrine-active chemicals found in food and the environment.

  3. Hybridized and isosteric analogues of N1-acetyl-N4-dimethyl-piperazinium iodide (ADMP) and N1-phenyl-N4-dimethyl-piperazinium iodide (DMPP) with central nicotinic action.

    Science.gov (United States)

    Manetti, D; Bartolini, A; Borea, P A; Bellucci, C; Dei, S; Ghelardini, C; Gualtieri, F; Romanelli, M N; Scapecchi, S; Teodori, E; Varani, K

    1999-03-01

    A series of piperazine derivatives, obtained by hybridization of N1-acetyl-N4-dimethyl-piperazinium iodide (1, ADMP) and N1-phenyl-N4-dimethyl-piperazinium iodide (3, DMPP) or of the corresponding tertiary bases (2, 4) with arecoline (5) and arecolone (6) or by isosteric substitution of the phenyl ring of DMPP, has been synthesized. Hybridization afforded compounds that, both as tertiary bases and as iodomethylates, have no affinity for the nicotinic receptor. On the contrary, isosteric substitution gave compounds that maintain affinity for the receptor; among them, two tertiary bases (37, 38), show affinity in the nanomolar range for the nicotinic receptor. The pharmacological profile of these isomeric compounds is quite interesting as they present differences in their peripheral and central effects, suggesting that they interact with different subtypes of the nicotinic receptor.

  4. Global sea-to-air flux climatology for bromoform, dibromomethane and methyl iodide

    Directory of Open Access Journals (Sweden)

    F. Ziska

    2013-02-01

    Full Text Available Volatile halogenated organic compounds containing bromine and iodine, which are naturally produced in the ocean, are involved in ozone depletion in both the troposphere and stratosphere. Three prominent compounds transporting large amounts of marine halogens into the atmosphere are bromoform (CHBr3, dibromomethane (CH2Br2 and methyl iodide (CH3I. The input of marine halogens to the stratosphere is based on observations and modeling studies using low resolution oceanic emission scenarios derived from top down approaches. In order to improve emission inventory estimates, we calculate data-based high resolution global sea-to-air flux estimates of these compounds from surface observations within the HalOcAt database (https://halocat.geomar.de/. Global maps of marine and atmospheric surface concentrations are derived from the data which are divided into coastal, shelf and open ocean regions. Considering physical and biogeochemical characteristics of ocean and atmosphere, the open ocean water and atmosphere data are classified into 21 regions. The available data are interpolated onto a 1° × 1° grid while missing grid values are interpolated with latitudinal and longitudinal dependent regression techniques reflecting the compounds' distributions. With the generated surface concentration climatologies for the ocean and atmosphere, global concentration gradients and sea-to-air fluxes are calculated. Based on these calculations we estimate a total global flux of 1.5/2.5 Gmol Br yr−1 for CHBr3, 0.78/0.98 Gmol Br yr−1 for CH2Br2 and 1.24/1.45 Gmol I yr−1 for CH3I (Robust Fit/Ordinary Least Square regression technique. Contrary to recent studies, negative fluxes occur in each sea-to-air flux climatology, mainly in the Arctic and Antarctic region. "Hot spots" for global

  5. The effect of temperature on radiolysis of iodide ion diluted aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Gorbovitskaya, T.; Tiliks, J. [Latvia Univ., Lab. of Radiation Chemistry, Riga (Latvia)

    1996-12-01

    To investigate the radiolysis of iodine containing aqueous solutions a flow type facility (ITF) has a possibility to irradiate aqueous solutions in the steel vessel with {sup 60}Co {gamma}-rays and continuously (on line) to analyze the products of radiolysis both in liquid and in gaseous phases. By means of ITF the formation of I{sub ox} (I{sub 2} + I{sub 3}{sup -} + HOI), IO{sub 3}{sup -}, H{sub 2}O{sub 2} was studied in 10{sup -5} - 10{sup -3} mol/dm{sup 3} CsI aqueous solutions by their radiolysis at dose rate 4.5 kGv/h for six hours in region of temperatures from 313 to 404 K. Some experiments in glass ampoules were also performed. The steady-state concentrations of I{sub ox} and IO{sub 3}{sup -} decreased with increasing temperature as linear function of inverted temperature. The effect decreased with decreasing concentration of iodide ion. As the result, at high temperatures (T{>=}380 K) the steady-state concentration of I{sub ox} does not depend essentially on the iodide ion initial concentration. Molecular iodine (I{sub 2}) released from the solution was the main radiolysis product in gaseous phase. Its steady-state concentration increased with increasing temperature because of iodine solubility in the water and decreased at the same time because the radiolytic iodine concentrations decreased. Therefore the most volatility of irradiated 10{sup -3} and 10{sup -4}M CsI solutions was observed at the temperature about 350 K. The volatility of 10{sup -5}M solutions gradually decreased with increasing temperature. The experimental data were explained on the base of the hypothesis that the reaction between I{sub 2} and radiolytic H{sub 2}O{sub 2} was the limit one determining the temperature dependence of I{sub ox} and IO{sub 3}{sup -}steady-state concentrations. Its activation energy was estimated to be 27,5 kcal.mol{sup -1}. The temperature dependence for reaction (IO{sup -} + H{sub 2}O{sub 2}) was also estimated. (author) 8 figs., 1 tab., 17 refs.

  6. Investigations regarding the wet decontamination of fluorescent lamp waste using iodine in potassium iodide solutions

    Energy Technology Data Exchange (ETDEWEB)

    Tunsu, Cristian, E-mail: tunsu@chalmers.se; Ekberg, Christian; Foreman, Mark; Retegan, Teodora

    2015-02-15

    Highlights: • A wet-based decontamination process for fluorescent lamp waste is proposed. • Mercury can be leached using iodine in potassium iodide solution. • The efficiency of the process increases with an increase in leachant concentration. • Selective leaching of mercury from rare earth elements is achieved. • Mercury is furthered recovered using ion exchange, reduction or solvent extraction. - Abstract: With the rising popularity of fluorescent lighting, simple and efficient methods for the decontamination of discarded lamps are needed. Due to their mercury content end-of-life fluorescent lamps are classified as hazardous waste, requiring special treatment for disposal. A simple wet-based decontamination process is required, especially for streams where thermal desorption, a commonly used but energy demanding method, cannot be applied. In this study the potential of a wet-based process using iodine in potassium iodide solution was studied for the recovery of mercury from fluorescent lamp waste. The influence of the leaching agent’s concentration and solid/liquid ratio on the decontamination efficiency was investigated. The leaching behaviour of mercury was studied over time, as well as its recovery from the obtained leachates by means of anion exchange, reduction, and solvent extraction. Dissolution of more than 90% of the contained mercury was achieved using 0.025/0.05 M I{sub 2}/KI solution at 21 °C for two hours. The efficiency of the process increased with an increase in leachant concentration. 97.3 ± 0.6% of the mercury contained was dissolved at 21 °C, in two hours, using a 0.25/0.5 M I{sub 2}/KI solution and a solid to liquid ratio of 10% w/v. Iodine and mercury can be efficiently removed from the leachates using Dowex 1X8 anion exchange resin or reducing agents such as sodium hydrosulphite, allowing the disposal of the obtained solution as non-hazardous industrial wastewater. The extractant CyMe{sub 4}BTBP showed good removal of mercury

  7. Global sea-to-air flux climatology for bromoform, dibromomethane and methyl iodide

    Directory of Open Access Journals (Sweden)

    F. Ziska

    2013-09-01

    Full Text Available Volatile halogenated organic compounds containing bromine and iodine, which are naturally produced in the ocean, are involved in ozone depletion in both the troposphere and stratosphere. Three prominent compounds transporting large amounts of marine halogens into the atmosphere are bromoform (CHBr3, dibromomethane (CH2Br2 and methyl iodide (CH3I. The input of marine halogens to the stratosphere has been estimated from observations and modelling studies using low-resolution oceanic emission scenarios derived from top-down approaches. In order to improve emission inventory estimates, we calculate data-based high resolution global sea-to-air flux estimates of these compounds from surface observations within the HalOcAt (Halocarbons in the Ocean and Atmosphere database (https://halocat.geomar.de/. Global maps of marine and atmospheric surface concentrations are derived from the data which are divided into coastal, shelf and open ocean regions. Considering physical and biogeochemical characteristics of ocean and atmosphere, the open ocean water and atmosphere data are classified into 21 regions. The available data are interpolated onto a 1°×1° grid while missing grid values are interpolated with latitudinal and longitudinal dependent regression techniques reflecting the compounds' distributions. With the generated surface concentration climatologies for the ocean and atmosphere, global sea-to-air concentration gradients and sea-to-air fluxes are calculated. Based on these calculations we estimate a total global flux of 1.5/2.5 Gmol Br yr−1 for CHBr3, 0.78/0.98 Gmol Br yr−1 for CH2Br2 and 1.24/1.45 Gmol Br yr−1 for CH3I (robust fit/ordinary least squares regression techniques. Contrary to recent studies, negative fluxes occur in each sea-to-air flux climatology, mainly in the Arctic and Antarctic regions. "Hot spots" for global polybromomethane emissions are located in the equatorial region, whereas methyl iodide emissions are enhanced in the

  8. An investigation into the use of cuprous chloride for the removal of radioactive iodide from aqueous solutions.

    Science.gov (United States)

    Liu, Yang; Gu, Ping; Jia, Lin; Zhang, Guanghui

    2016-01-25

    Cuprous chloride (CuCl) was examined as a precipitant to remove iodide (I(-)) from aqueous solutions. The effects of the dosage of CuCl, reaction time, initial concentrations of I(-) and bicarbonate (HCO3(-)) on I(-) removal were investigated. The results showed that the optimized removal efficiency of I(-) reached approximately 95.8% when the dosage was 150 mg/L, the initial I(-) concentration ranged from 5 to 40 mg/L and the reaction time was 15 min. The removal efficiency decreased from 95.8% to 76.0% with the addition of HCO3(-) at a concentration in the range of 0-107 mg/L. Furthermore, the dissociation of CuCl, the disproportionation reaction of Cu(+), the precipitation of cuprous iodide (CuI) and cuprous oxide (Cu2O), and the formations of copper sulfide (CuxS, 1≤xradioactive I(-) pollution in water.

  9. Two-step functionalization of oligosaccharides using glycosyl iodide and trimethylene oxide and its applications to multivalent glycoconjugates.

    Science.gov (United States)

    Hsieh, Hsiao-Wu; Davis, Ryan A; Hoch, Jessica A; Gervay-Hague, Jacquelyn

    2014-05-19

    Oligosaccharide conjugates, such as glycoproteins and glycolipids, are potential chemotherapeutics and also serve as useful tools for understanding the biological roles of carbohydrates. With many modern isolation and synthetic technologies providing access to a wide variety of free sugars, there is increasing need for general methodologies for carbohydrate functionalization. Herein, we report a two-step methodology for the conjugation of per-O-acetylated oligosaccharides to functionalized linkers that can be used for various displays. Oligosaccharides obtained from both synthetic and commercial sources were converted to glycosyl iodides and activated with I2 to form reactive donors that were subsequently trapped with trimethylene oxide to form iodopropyl conjugates in a single step. The terminal iodide served as a chemical handle for further modification. Conversion into the corresponding azide followed by copper-catalyzed azide-alkyne cycloaddition afforded multivalent glycoconjugates of Gb3 for further investigation as anti-cancer therapeutics.

  10. Thyroglobulin in smoking mothers and their newborns at delivery suggests autoregulation of placental iodide transport overcoming thiocyanate inhibition

    DEFF Research Database (Denmark)

    Andersen, Stine L; Backman Nøhr, Susanne; Wu, Chun S;

    2013-01-01

    ). The pregnant women reported on intake of iodine-containing supplements during pregnancy and Tg in maternal serum at delivery and in cord serum were analyzed. RESULTS: In a context of mild-to-moderate iodine deficiency, smoking mothers had significantly higher serum Tg than nonsmoking mothers (mean Tg smokers...... maternal smoking, but compensatory autoregulation of iodide transport differs between organs. The extent of autoregulation of placental iodide transport remains to be clarified. OBJECTIVE: To compare the impact of maternal smoking on thyroglobulin (Tg) levels in maternal serum at delivery and in cord serum...... as markers of maternal and fetal iodine deficiency. METHODS: One hundred and forty healthy, pregnant women admitted for delivery and their newborns were studied before the iodine fortification of salt in Denmark. Cotinine in urine and serum classified mothers as smokers (n=50) or nonsmokers (n=90...

  11. Corrosion Inhibition Propargyl Alcohol on Low Alloy Cr Steel in 0.5 M H2SO4 in the Absence and Presence of Potassium Iodide

    OpenAIRE

    Baghaei Ravari, Fatemeh; Heydari, Mahdi; Dadgarineghad, Athareh

    2011-01-01

    The corrosion and inhibition behaviors of low alloy Cr steel in sulfuric acid in the presence of propargyl alcohol (PA) and potassium iodide (KI) have been studied using Electrochemical Impedance Spectroscopy (EIS) and Tafel polarization method. It was found that the inhibition efficiency increased with PA concentration. The addition of potassium iodide to propargyl alcohol in solution increased the inhibition efficiency of propargyl alcohol. A synergistic effect was observed between KI and P...

  12. Corrosion Inhibition Propargyl Alcohol on Low Alloy Cr Steel in 0.5 M H2SO4 in the Absence and Presence of Potassium Iodide

    OpenAIRE

    Baghaei Ravari, Fatemeh; Heydari, Mahdi; Dadgarineghad, Athareh

    2010-01-01

    The corrosion and inhibition behaviors of low alloy Cr steel in sulfuric acid in the presence of propargyl alcohol (PA) and potassium iodide (KI) have been studied using Electrochemical Impedance Spectroscopy (EIS) and Tafel polarization method. It was found that the inhibition efficiency increased with PA concentration. The addition of potassium iodide to propargyl alcohol in solution increased the inhibition efficiency of propargyl alcohol. A synergistic effect was observed between KI and P...

  13. The reaction of carbon disulphide with -haloketones and primary amines in the presence of potassium iodide as catalyst

    Indian Academy of Sciences (India)

    Javad Safaei-Ghomi; Fariba Salimi; Ali Ramazani

    2013-09-01

    A simple, mild and convenient method has been developed for the synthesis of 3,4,5-trialkyl-1,3-thiazole-2(3)-thione derivatives through one pot three-component reaction between a primary amine, carbon disulphide, and -haloketone in the presence of potassium iodide at room temperature conditions. The products were obtained with excellent yield and appropriate reaction times. This reaction represents a rapid and unprecedented route to the described molecules that have biological specifications.

  14. Broad-Spectrum Antimicrobial Effects of Photocatalysis Using Titanium Dioxide Nanoparticles Are Strongly Potentiated by Addition of Potassium Iodide.

    Science.gov (United States)

    Huang, Ying-Ying; Choi, Hwanjun; Kushida, Yu; Bhayana, Brijesh; Wang, Yuguang; Hamblin, Michael R

    2016-09-01

    Photocatalysis describes the excitation of titanium dioxide nanoparticles (a wide-band gap semiconductor) by UVA light to produce reactive oxygen species (ROS) that can destroy many organic molecules. This photocatalysis process is used for environmental remediation, while antimicrobial photocatalysis can kill many classes of microorganisms and can be used to sterilize water and surfaces and possibly to treat infections. Here we show that addition of the nontoxic inorganic salt potassium iodide to TiO2 (P25) excited by UVA potentiated the killing of Gram-positive bacteria, Gram-negative bacteria, and fungi by up to 6 logs. The microbial killing depended on the concentration of TiO2, the fluence of UVA light, and the concentration of KI (the best effect was at 100 mM). There was formation of long-lived antimicrobial species (probably hypoiodite and iodine) in the reaction mixture (detected by adding bacteria after light), but short-lived antibacterial reactive species (bacteria present during light) produced more killing. Fluorescent probes for ROS (hydroxyl radical and singlet oxygen) were quenched by iodide. Tri-iodide (which has a peak at 350 nm and a blue product with starch) was produced by TiO2-UVA-KI but was much reduced when methicillin-resistant Staphylococcus aureus (MRSA) cells were also present. The model tyrosine substrate N-acetyl tyrosine ethyl ester was iodinated in a light dose-dependent manner. We conclude that UVA-excited TiO2 in the presence of iodide produces reactive iodine intermediates during illumination that kill microbial cells and long-lived oxidized iodine products that kill after light has ended.

  15. Research into Uncertainty in Measurement of Seawater Chemical Oxygen Demand by Potassium Iodide-Alkaline Potassium Permanganate Determination Method.

    OpenAIRE

    Zhang, Shiqiang; Guo, Changsong

    2007-01-01

    Using the glucose and L-glutamic-acid to prepare the standard substance according to the ratio of 1:1, and the artificial seawater and the standard substance to prepare a series of standard solutions, the distribution pattern of uncertainty in measurement of seawater COD is obtained based on the measured results of the series of standard solutions by the potassium iodide-alkaline potassium permanganate determination method. The distribution pattern is as follows: Uncertainty in measurement is...

  16. Potassium iodate and its comparison to potassium iodide as a blocker of 131I uptake by the thyroid in rats.

    Science.gov (United States)

    Pahuja, D N; Rajan, M G; Borkar, A V; Samuel, A M

    1993-11-01

    Potassium iodide is the preferred thyroid blocker for personnel handling radioiodine and is recommended as a prophylaxis for the population in the near-field of a nuclear reactor which would be likely to be exposed to radioiodine in an accidental breach of containment. However, in hot and humid climates, this hygroscopic chemical has a poor shelf life due to hydrolytic loss of iodine vapors. On the other hand, another iodine-rich salt, potassium iodate (KIO3), is quite stable and has a much longer shelf life. The present study compares potassium iodide and KIO3 as thyroid blockers and examines the appropriate time at which they should be administered in case of radioiodine exposure. Either of the two were given in recommended dosage (100 mg stable iodine per 70 kg body weight) at -2, 0, +2, +4, +6, and +8 h after administration of tracer quantities of radioiodine (131I) to age-, weight-, and sex-matched rats. 131I uptake in thyroid was measured 24 h after its administration in the experimental animals and compared with placebo administered controls. Results suggest that KIO3 is as effective a thyroid blocking agent as potassium iodide. In comparison to controls, 24-h thyroid uptake of 131I can be substantially reduced if potassium iodide or KIO3 is given to the animals within 2-4 h after exposure to 131I. Another noteworthy observation is that KIO3 is effective even at 8 h when administered at twice the usual dosage in comparison to the single dose, which does not show appreciable thyroid blocking properties after 8 h.

  17. Formation and Characterization of Mixed Crystals Based on Bis (Thiourea)Cadmium Chloride and Bis (Thiourea)Cadmium Iodide

    OpenAIRE

    2014-01-01

    Bis(thiourea)cadmium chloride(BTCC) and bis(thiourea)cadmium iodide (BTCI) are metal complexes of thiourea having better nonlinear optical properties than KH2PO4. An attempt has been made in the present study to form mixed crystals based on BTCC and BTCI (even though their crystal lattices mismatch) from aqueous solutions, the precursors mixed in proper proportions. A total of seven (including the end members) crystals were formed by the free evaporation method and characteriz...

  18. Evaluation of iodide and iodate for adsorption-desorption characteristics and bioavailability in three types of soil.

    Science.gov (United States)

    Hong, Chunlai; Weng, Huanxin; Jilani, Ghulam; Yan, Ailan; Liu, Huiping; Xue, Zhiyong

    2012-05-01

    Adsorption-desorption of iodine in two forms, viz., iodide (I(-)) and iodate (IO (3) (-) ), in three types of soil were investigated. The soils were: red soil developed on Quaternary red earths (REQ)- clayey, kaolintic thermic plinthite Aquult, Inceptisol soil (IS) and alluvial soil (AS)-Fluvio-marine yellow loamy soil. The isothermal curves of iodine adsorption on soils were described by Langmuir and Freundlich equation, and the maximum adsorption values (y (m)) were obtained from the simple Langmuir model. As compared with the iodide, the iodate was adsorbed in higher amounts by the soils tested. Among three soils, the REQ soil adsorbed more iodine (I(-) and IO (3) (-) ) than the IS and AS. The distribution coefficient (K (d)) of iodine in the soils decreased exponentially with increasing iodine loading concentration. Desorption of iodine in soil was increased correspondingly with increasing adsorption values. The REQ soil had a greater affinity for iodine than the IS and AS at the same iodine loadings. In the pot experiment cultivated with pakchoi (Brassica chinensis L.) and added with two exogenous iodine sources, the iodide form was quickly taken up by pakchoi and caused more toxicity to the vegetable. The rate of iodine loss from soil was higher for iodide form as compared with the iodate. The iodine bioavailability was the highest but the persistence was the weakest in AS among the three soils tested, and the REQ soil showed just the opposite trend to that of the AS soil. This study is of theoretical importance to understand the relationship between iodine adsorption-desorption characteristics and their bioavailability in different soils and it also has practical implications for seeking effective alternatives of iodine biofortification to prevent iodine deficiency disorders.

  19. Consequences of stoichiometric error on nuclear DNA content evaluation in Coffea liberica var. dewevrei using DAPI and propidium iodide.

    Science.gov (United States)

    Noirot, Michel; Barre, Philippe; Louarn, Jacques; Duperray, Christophe; Hamon, Serge

    2002-04-01

    The genome size of coffee trees (Coffea sp.) was assessed using flow cytometry. Nuclear DNA was stained with two dyes [4',6-diamino-2-phenylindole dihydrochloride hydrate (DAPI) and propidium iodide (PI)]. Fluorescence in coffee tree nuclei (C-PI or C-DAPI) was compared with that of the standard, petunia (P-PI or P-DAPI). If there is no stoichiometric error, then the ratio between fluorescence of the target nuclei and that of the standard nuclei (R-PI or R-DAPI) is expected to be proportional to the genome size. Between-tree differences in target : standard fluorescence ratios were noted in Coffea liberica var. dewevrei using propidium iodide and DAPI. For both dyes, between-tree differences were due to a lack of proportionality when comparing locations of the coffee peak and the petunia peak. Intraspecific genome size variations clearly cannot explain variations in the target : standard fluorescence ratio. The origin of the lack of proportionality between target and standard fluorescences differed for the two dyes. With propidium iodide, there was a regression line convergence point, and no between-tree differences were noted in this respect, whereas there was no such convergence with DAPI. An accurate estimate of genome size can thus be obtained with PI. Implications with respect to accessibility and binding mode are discussed.

  20. Room temperature fluorescence and phosphorescence study on the interactions of iodide ions with single tryptophan containing serum albumins

    Science.gov (United States)

    Gałęcki, Krystian; Kowalska-Baron, Agnieszka

    2016-12-01

    In this study, the influence of heavy-atom perturbation, induced by the addition of iodide ions, on the fluorescence and phosphorescence decay parameters of some single tryptophan containing serum albumins isolated from: human (HSA), equine (ESA) and leporine (LSA) has been studied. The obtained results indicated that, there exist two distinct conformations of the proteins with different exposure to the quencher. In addition, the Stern-Volmer plots indicated saturation of iodide ions in the binding region. Therefore, to determine quenching parameter, we proposed alternative quenching model and we have performed a global analysis of each conformer to define the effect of iodide ions in the cavity by determining the value of the association constant. The possible quenching mechanism may be based on long-range through-space interactions between the buried chromophore and quencher in the aqueous phase. The discrepancies of the decay parameters between the albumins studied may be related with the accumulation of positive charge at the main and the back entrance to the Drug Site 1 where tryptophan residue is located.

  1. Comparison of two novel in-syringe dispersive liquid-liquid microextraction techniques for the determination of iodide in water samples using spectrophotometry.

    Science.gov (United States)

    Kaykhaii, Massoud; Sargazi, Mona

    2014-01-01

    Two new, rapid methodologies have been developed and applied successfully for the determination of trace levels of iodide in real water samples. Both techniques are based on a combination of in-syringe dispersive liquid-liquid microextraction (IS-DLLME) and micro-volume UV-Vis spectrophotometry. In the first technique, iodide is oxidized with nitrous acid to the colorless anion of ICl2(-) at high concentration of hydrochloric acid. Rhodamine B is added and by means of one step IS-DLLME, the ion-pair formed was extracted into toluene and measured spectrophotometrically. Acetone is used as dispersive solvent. The second method is based on the IS-DLLME microextraction of iodide as iodide/1, 10-phenanthroline-iron((II)) chelate cation ion-pair (colored) into nitrobenzene. Methanol was selected as dispersive solvent. Optimal conditions for iodide extraction were determined for both approaches. Methods are compared in terms of analytical parameters such as precision, accuracy, speed and limit of detection. Both methods were successfully applied to determining iodide in tap and river water samples.

  2. Comparison of two novel in-syringe dispersive liquid-liquid microextraction techniques for the determination of iodide in water samples using spectrophotometry

    Science.gov (United States)

    Kaykhaii, Massoud; Sargazi, Mona

    2014-03-01

    Two new, rapid methodologies have been developed and applied successfully for the determination of trace levels of iodide in real water samples. Both techniques are based on a combination of in-syringe dispersive liquid-liquid microextraction (IS-DLLME) and micro-volume UV-Vis spectrophotometry. In the first technique, iodide is oxidized with nitrous acid to the colorless anion of ICl2- at high concentration of hydrochloric acid. Rhodamine B is added and by means of one step IS-DLLME, the ion-pair formed was extracted into toluene and measured spectrophotometrically. Acetone is used as dispersive solvent. The second method is based on the IS-DLLME microextraction of iodide as iodide/1, 10-phenanthroline-iron(II) chelate cation ion-pair (colored) into nitrobenzene. Methanol was selected as dispersive solvent. Optimal conditions for iodide extraction were determined for both approaches. Methods are compared in terms of analytical parameters such as precision, accuracy, speed and limit of detection. Both methods were successfully applied to determining iodide in tap and river water samples.

  3. A colorimetric method for highly sensitive and accurate detection of iodide by finding the critical color in a color change process using silver triangular nanoplates

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Xiu-Hua; Ling, Jian, E-mail: lingjian@ynu.edu.cn; Peng, Jun; Cao, Qiu-E., E-mail: qecao@ynu.edu.cn; Ding, Zhong-Tao; Bian, Long-Chun

    2013-10-10

    Graphical abstract: -- Highlights: •Demonstrated a new colorimetric strategy for iodide detection by silver nanoplates. •The colorimetric strategy is to find the critical color in a color change process. •The colorimetric strategy is more accurate and sensitive than common colorimetry. •Discovered a new morphological transformation phenomenon of silver nanoplates. -- Abstract: In this contribution, we demonstrated a novel colorimetric method for highly sensitive and accurate detection of iodide using citrate-stabilized silver triangular nanoplates (silver TNPs). Very lower concentration of iodide can induce an appreciable color change of silver TNPs solution from blue to yellow by fusing of silver TNPs to nanoparticles, as confirmed by UV–vis absorption spectroscopy and transmission electron microscopy (TEM). The principle of this colorimetric assay is not an ordinary colorimetry, but a new colorimetric strategy by finding the critical color in a color change process. With this strategy, 0.1 μM of iodide can be recognized within 30 min by naked-eyes observation, and lower concentration of iodide down to 8.8 nM can be detected using a spectrophotometer. Furthermore, this high sensitive colorimetric assay has good accuracy, stability and reproducibility comparing with other ordinary colorimetry. We believe this new colorimetric method will open up a fresh insight of simple, rapid and reliable detection of iodide and can find its future application in the biochemical analysis or clinical diagnosis.

  4. Conversion of iodide to hypoiodous acid and iodine in aqueous microdroplets exposed to ozone.

    Science.gov (United States)

    Pillar, Elizabeth A; Guzman, Marcelo I; Rodriguez, Jose M

    2013-10-01

    Halides are incorporated into aerosol sea spray, where they start the catalytic destruction of ozone (O3) over the oceans and affect the global troposphere. Two intriguing environmental problems undergoing continuous research are (1) to understand how reactive gas phase molecular halogens are directly produced from inorganic halides exposed to O3 and (2) to constrain the environmental factors that control this interfacial process. This paper presents a laboratory study of the reaction of O3 at variable iodide (I(-)) concentration (0.010-100 μM) for solutions aerosolized at 25 °C, which reveal remarkable differences in the reaction intermediates and products expected in sea spray for low tropospheric [O3]. The ultrafast oxidation of I(-) by O3 at the air-water interface of microdroplets is evidenced by the appearance of hypoiodous acid (HIO), iodite (IO2(-)), iodate (IO3(-)), triiodide (I3(-)), and molecular iodine (I2). Mass spectrometry measurements reveal an enhancement (up to 28%) in the dissolution of gaseous O3 at the gas-liquid interface when increasing the concentration of NaI or NaBr from 0.010 to 100 μM. The production of iodine species such as HIO and I2 from NaI aerosolized solutions exposed to 50 ppbv O3 can occur at the air-water interface of sea spray, followed by their transfer to the gas-phase, where they contribute to the loss of tropospheric ozone.

  5. Dipole Alignment at the Carbon Nanotube and Methyl Ammonium Lead Iodide Perovskite Interface

    Energy Technology Data Exchange (ETDEWEB)

    Przepioski, Joshua [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2015-08-28

    This work correlates resonant peaks from first principles calculation on ammonia (NH3) Nitrogen 1s x-ray absorption spectroscopy (XAS) within the methyl ammonium lead iodide perovskite (CH3NH3PbI3), and proposes a curve to determine the alignment of the methyl ammonium dipole if there exists angular dependence. The Nitrogen 1s XAS was performed at varying incident angles on the perovskite with and without a carbon nanotube (CNT) interface produced from an ultrasonic spray deposition. We investigated the peak contribution from PbI2 and the poly(9,9-dioctylfluorene- 2,7-diyl) with bipyridine (PFO-BPy) wrapped around the CNT, and used normalization techniques to better identify the dipole alignment. There was angular dependence on samples containing the CNT interface suggesting an existing dipole alignment, but there was no angular dependence on the perovskite samples alone; however, more normalization techniques and experimental work must be performed in order to ensure its validity and to better describe its alignment, and possible controlling factors.

  6. Structures, Phase Transitions and Tricritical Behavior of the Hybrid Perovskite Methyl Ammonium Lead Iodide

    Science.gov (United States)

    Whitfield, P. S.; Herron, N.; Guise, W. E.; Page, K.; Cheng, Y. Q.; Milas, I.; Crawford, M. K.

    2016-10-01

    We have examined the crystal structures and structural phase transitions of the deuterated, partially deuterated and hydrogenous organic-inorganic hybrid perovskite methyl ammonium lead iodide (MAPbI3) using time-of-flight neutron and synchrotron X-ray powder diffraction. Near 330 K the high temperature cubic phases transformed to a body-centered tetragonal phase. The variation of the order parameter Q for this transition scaled with temperature T as Q ˜ (Tc-T)β, where Tc is the critical temperature and the exponent β was close to ¼, as predicted for a tricritical phase transition. However, we also observed coexistence of the cubic and tetragonal phases over a range of temperature in all cases, demonstrating that the phase transition was in fact first-order, although still very close to tricritical. Upon cooling further, all the tetragonal phases transformed into a low temperature orthorhombic phase around 160 K, again via a first-order phase transition. Based upon these results, we discuss the impact of the structural phase transitions upon photovoltaic performance of MAPbI3 based solar cells.

  7. Methylammonium lead iodide grain boundaries exhibit depth-dependent electrical properties

    Energy Technology Data Exchange (ETDEWEB)

    MacDonald, Gordon A.; Yang, Mengjin; Berweger, Samuel; Killgore, Jason P.; Kabos, Pavel; Berry, Joseph J.; Zhu, Kai; DelRio, Frank W.

    2016-01-01

    In this communication, the nanoscale through-film and lateral photo-response and conductivity of large-grained methylammonium lead iodide (MAPbI3) thin films are studied. In perovskite solar cells (PSC), these films result in efficiencies >17%. The grain boundaries (GBs) show high resistance at the top surface of the film, and act as an impediment to photocurrent collection. However, lower resistance pathways between grains exist below the top surface of the film, indicating that there exists a depth-dependent resistance of GBs (RGB(z)). Furthermore, lateral conductivity measurements indicate that RGB(z) exhibits GB-to-GB heterogeneity. These results indicate that increased photocurrent collection along GBs is not a prerequisite for high-efficiency PSCs. Rather, better control of depth-dependent GB electrical properties, and an improvement in the homogeneity of the GB-to-GB electrical properties, must be managed to enable further improvements in PSC efficiency. Finally, these results refute the implicit assumption seen in the literature that the electrical properties of GBs, as measured at the top surface of the perovskite film, necessarily reflect the electrical properties of GBs within the thickness of the film.

  8. Thickness dependence of structural and optical properties of cadmium iodide thin films

    Energy Technology Data Exchange (ETDEWEB)

    Yahia, I.S. [Department of Physics, Faculty of Science, King Khalid University, P.O. Box 9004, Abha (Saudi Arabia); Centre of Nanotechnology, King AbdulAziz University, Jeddah (Saudi Arabia); Shapaan, M. [Department of Physics, Faculty of Science, Al-Azahar University, Cairo (Egypt); Ismail, Yasser A.M.; Aboraia, A.M. [Department of Physics, Faculty of Science, Al-Azahar University, Assiut 71542 (Egypt); Shaaban, E.R., E-mail: esamramadan2008@yahoo.com [Department of Physics, Faculty of Science, Al-Azahar University, Assiut 71542 (Egypt)

    2015-07-05

    Highlights: • Different thicknesses of CdI{sub 2} films were prepared. • Both crystallite size and microstrain of the films has been determined. • The room temperature reflectance and transmittance data are analyzed. • The refractive index and energy gap are determined. - Abstract: Structural and optical properties as a function of film thickness have been studied for the thermally evaporated cadmium iodide (CdI{sub 2}) films. According to XRD structure, the thickness of investigated films extends from 272 to 696 nm, showing hexagonal structure and good c-axis alignment normal to glass substrate plane. Both of crystallite size and lattice strain have been determined in terms of Voight method of the main peak. The optical constants, refractive index (n), and extinction coefficient (k) have been determined using envelope method. The optical absorption data indicates an allowed direct inter – band transition near the absorption edge with an optical energy gap that decreases continuously from 3.572 to 3.767 eV. Both of optical constants and energy gap show thickness dependence that can be explained in terms of structure parameters, crystallite size, and lattice strain.

  9. Growth kinetics and morphology of mercuric iodide crystals grown by physical vapor transport

    Energy Technology Data Exchange (ETDEWEB)

    Nason, D. [TN Technologies, Round Rock, TX (United States); Mihalik, G. [Siemens Solar Inc., Vancouver, Washington (United States); Monchamp, R. [ROMOCO, Santa Barbara, California (United States)

    1997-06-02

    The growth kinetics of mercuric iodide single crystals grown by physical vapor transport from synthesized material were measured using an instrumented growth ampoule, and in situ crystal size resolution to {+-}0.2{mu}m was achieved. The kinetic coefficients are 2x10{sup -4}mm/s and 1.3x10{sup -4}mm/s for (001) and (110), respectively, as found from extrapolating the measured (apparent) kinetic coefficients to zero crystal size. The kinetic coefficients are nearly independent of growth rate in the practical range, {approx}1-5mm/day, indicating linear growth kinetics, and have substantial temperature coefficients of 0.3x10{sup -6}mm/(sC) and 0.4x10{sup -6}mm/(sC), respectively. The results indicate that the growth process is kinetically controlled at small crystal sizes and undergoes a transition to transport control at {approx}30-40mm crystal size, depending on the particular face. The results are consistent with a layer spreading process of growth in which adsorbed molecules surface-diffuse with activation energies congruent with 4kcal/mol and congruent with 8kcal/mol for (001) and (110), respectively

  10. Cesium Iodide Crystal Calorimeter of the Proton Computed Tomography (pCT) Imager

    Science.gov (United States)

    Missaghian, Jessica; Sadrozinski, Hartmut; Colby, Brian; Rykalin, Victor; Hurley, Ford

    2009-11-01

    Researchers at SCIPP, LLMU and NIU have collaborated to make a functioning proton imager. Proton Computed Tomography (pCT) is designated to be applied in proton therapy of human cancer systems. It will image head-sized phantom objects and provide excellent space and energy resolution using a silicon microstrip tracker and crystal calorimetry. The residual energy could be measured with precision of a few percent using a Cesium Iodide crystal calorimeter. A single element of the CsI(TI) calorimeter was tested in order to understand the behavior of the future calorimeter system. We present test results on a CsI(TI) calorimeter element with proton beams of 35, 100 and 200MeV. The detector element was designed to comply with the demands of high energy resolution of a few percent and a dynamic range of two orders of magnitude (1-300MeV) under a counting rate of 10 kHz per channel. We also report on cosmic measurement results of each crystal of the future calorimeter matrix. A detailed description of the calorimeter data acquisition system will be given.

  11. Crystal structure of 4-{2-[4-(dimethylaminophenyl]diazen-1-yl}-1-methylpyridinium iodide

    Directory of Open Access Journals (Sweden)

    Katherine Chulvi

    2015-12-01

    Full Text Available The molecular geometry of the ionic title compound, C14H17N4+·I− or DAZOP+·I−, is essentially featureless. Regarding the crystal structure, in addition to the obvious cation–anion Coulombic interactions, the packing is mostly directed by non-covalent interactions involving both ring systems, as well as the iodide anion. It consists of cationic molecules aligned along [101] and disposed in an antiparallel fashion while linked into π-bonded dimeric entities by a stacking contact involving symmetry-related phenyl rings, with a centroid–centroid distance of 3.468 (3 Å and a slippage of 0.951 Å. The dimers are, in addition, sustained by a number of C—H...I and I...π (I...centroid = 3.876 Å interactions involving the anion. Finally, interdimeric contacts are of the C—H...I and C—H...π types.

  12. Amorphous silicon pixel layers with cesium iodide converters for medical radiography

    Energy Technology Data Exchange (ETDEWEB)

    Jing, T.; Cho, G. [Lawrence Berkeley Lab., CA (United States); Goodman, C.A. [Air Techniques, Inc., Hicksville, NY (United States)] [and others

    1993-11-01

    We describe the properties of evaporated layers of Cesium Iodide (Thallium activated) deposited on substrates that enable easy coupling to amorphous silicon pixel arrays. The CsI(Tl) layers range in thickness from 65 to 220{mu}m. We used the two-boat evaporator system to deposit CsI(Tl) layers. This system ensures the formation of the scintillator film with homogenous thallium concentration which is essential for optimizing the scintillation light emission efficiency. The Tl concentration was kept to 0.1--0.2 mole percent for the highest light output. Temperature annealing can affect the microstructure as well as light output of the CsI(Tl) film. 200--300C temperature annealing can increase the light output by a factor of two. The amorphous silicon pixel arrays are p-i-n diodes approximately l{mu}m thick with transparent electrodes to enable them to detect the scintillation light produced by X-rays incident on the CsI(Tl). Digital radiography requires a good spatial resolution. This is accomplished by making the detector pixel size less then 50{mu}m. The light emission from the CsI(Tl) is collimated by techniques involving the deposition process on pattered substrates. We have measured MTF of greater than 12 line pairs per mm at the 10% level.

  13. Fluorescence Quenching and Binding Interaction of l0-Methylacridinium Iodide to Nucleic Acids

    Institute of Scientific and Technical Information of China (English)

    孙险峰; 江致勤; 丁兵林

    2003-01-01

    Interaction of 10-methylacridinium iodide (MAI) as fluorescence probe with nucleobases, nucleosides and nucleic acids has been studied by UV-visible absorption and fluorescence spectroscopy. It was found that fluorescence of MAI is strongly quenched by the nucleobases, nucleosides and nucleic acids, respectively. The quenching follows the Stern-Volmer linear equation. The fluorescence quenching rate constant (kq) was measured to be 109-1010 (L/mol)/s within the range of diffusion-controlled rate limit, indicating that the interaction between MAI and nucleic acid and their precursors is characteristic of electron transfer mechanism. In addition, the binding interaction model of MAI to calf thymus DNA (ct-DNA) was further investigated. Apparent hypochromism in the absorption spectra of MAI was observed when MAI binds to ct-DNA.Three spectroscopic methods, which include (1) UV spectroscopy, (2) fluorescence quenching of MAI, (3) competitive dual-probe method of MAI and ethidium bromide (EB), were utilized to determine the affinity binding constants (K)of MAI and ct-DNA. The binding constants K obtained from the above methods gave consistent data in the same range (1.0-5.5) ×104 L/mol, which lend credibility to these measurements. The binding site number was determined to be 1.9. The influence of thermal denaturation and phosphate concentration on the binding was examined. The binding model of MAI to ct-DNA including intercalation and outside binding was investigated.

  14. Mercuric iodide room-temperature array detectors for gamma-ray imaging

    Energy Technology Data Exchange (ETDEWEB)

    Patt, B. [Xsirius, Inc, Camarillo, CA (United States)

    1994-11-15

    Significant progress has been made recently in the development of mercuric iodide detector arrays for gamma-ray imaging, making real the possibility of constructing high-performance small, light-weight, portable gamma-ray imaging systems. New techniques have been applied in detector fabrication and then low noise electronics which have produced pixel arrays with high-energy resolution, high spatial resolution, high gamma stopping efficiency. Measurements of the energy resolution capability have been made on a 19-element protypical array. Pixel energy resolutions of 2.98% fwhm and 3.88% fwhm were obtained at 59 keV (241-Am) and 140-keV (99m-Tc), respectively. The pixel spectra for a 14-element section of the data is shown together with the composition of the overlapped individual pixel spectra. These techniques are now being applied to fabricate much larger arrays with thousands of pixels. Extension of these principles to imaging scenarios involving gamma-ray energies up to several hundred keV is also possible. This would enable imaging of the 208 keV and 375-414 keV 239-Pu and 240-Pu structures, as well as the 186 keV line of 235-U.

  15. Dimethyl phenyl piperazine iodide (DMPP) induces glioma regression by inhibiting angiogenesis.

    Science.gov (United States)

    He, Yan-Qing; Li, Yan; Wang, Xiao-Yu; He, Xiao-Dong; Jun, Li; Chuai, Manli; Lee, Kenneth Ka Ho; Wang, Ju; Wang, Li-Jing; Yang, Xuesong

    2014-01-15

    1,1-Dimethyl-4-phenyl piperazine iodide (DMPP) is a synthetic nicotinic acetylcholine receptor (nAChR) agonist that could reduce airway inflammation. In this study, we demonstrated that DMPP could dramatically inhibit glioma size maintained on the chick embryonic chorioallantoic membrane (CAM). We first performed MTT and BrdU incorporation experiments on U87 glioma cells in vitro to understand the mechanism involved. We established that DMPP did not significantly affect U87 cell proliferation and survival. We speculated that DMPP directly caused the tumor to regress by affecting the vasculature in and around the implanted tumor on our chick CAM model. Hence, we conducted detailed analysis of DMPP's inhibitory effects on angiogenesis. Three vasculogenesis and angiogenesis in vivo models were used in the study which included (1) early chick blood islands formation, (2) chick yolk-sac membrane (YSW) and (3) CAM models. The results revealed that DMPP directly suppressed all developmental stages involved in vasculogenesis and angiogenesis - possibly by acting through Ang-1 and HIF-2α signaling. In sum, our results show that DMPP could induce glioma regression grown on CAM by inhibiting vasculogenesis and angiogenesis.

  16. Experimental and analytical study on cesium iodide behavior in piping in wave experiment

    Energy Technology Data Exchange (ETDEWEB)

    Hidaka, A.; Igarashi, M.; Hashimoto, K.; Sugimoto, J. [Japan Atomic Energy Research Inst., Dep. of Reactor Safety Research, Tokai-mura (Japan); Yoshino, T. [Toshiba Advanced System Corp., Isago Kawasaki-ku (Japan)

    1996-12-01

    The WAVE (Wide range Aerosol model VErification) experiments have been performed at JAERI to investigate cesium iodide (CsI) deposition onto an inner surface of piping wall under typical severe accident conditions. The test facility consists of a dish containing CsI powder, electrical heaters and a straight pipe of 1.5 m in length with diameter of 0.042m. Nitrogen gas and superheated steam were injected into the pipe to carry the vaporized CsI and to simulate the thermohydraulic condition for the PWR hot-leg inlet. Analyses of the experiments have been conducted with a three-dimensional thermohydraulic code, SPRAC and the radionuclide behavior analysis codes, ART and VICTORIA. A clear difference was found in the deposition behavior between nitrogen and steam conditions as carrier gases. For nitrogen gas, the analyses well reproduced the experimental results by closely coupling the CsI behavior and the detailed thermohydraulic analyses. For steam carrier gas, on the contrary, the experimental results could not be well reproduced without the use of larger aerosol size. Since the observed enhancement of aerosol size in superheated steam cannot be explained by existing models, it is necessary to further investigate this mechanisms by experiment and analysis. (author) 34 figs., 23 refs.

  17. Effects of iodide on the fluorescence and activity of the hydroperoxyflavin intermediate of Vibrio harveyi luciferase.

    Science.gov (United States)

    Huang, Shouqin; Tu, Shiao-Chun

    2005-01-01

    The 4a-hydroperoxy-4a,5-dihydroFMN intermediate (II or HFOOH) of Vibrio harveyi luciferase is known to transform from a low quantum yield IIx to a high quantum yield (lambdamax 485 nm, uncorrected) IIy fluorescent species on exposure to excitation light. Similar results were observed with II prepared from the alphaH44A luciferase mutant, which is very weak in bioluminescence activity. Because of the rapid decay of the alphaH44A II, its true fluorescence was obscured by the more intense 520 nm fluorescence (uncorrected) from its decay product oxidized flavin mononucleotide (FMN). Potassium iodide (KI) at 0.2 M was effective in quenching the FMN fluorescence, leaving the 485 nm fluorescence of II from both the wild-type (WT) and alphaH44A luciferase readily detectable. For both II species, the luciferase-bound peroxyflavin was well shielded from KI quenching. KI also enhanced the decay rates of both the WT and alphaH44A II. For alphaH44A, the transformation of IIx to IIy can be induced by KI in the dark, and it is proposed to be a consequence of a luciferase conformational change. The WT II formed a bioluminescence-inactive complex with KI, resulting in two distinct decay time courses based on absorption changes and decreases of bioluminescence activity of II.

  18. Direct-indirect character of the bandgap in methylammonium lead iodide perovskite

    Science.gov (United States)

    Hutter, Eline M.; Gélvez-Rueda, María C.; Osherov, Anna; Bulović, Vladimir; Grozema, Ferdinand C.; Stranks, Samuel D.; Savenije, Tom J.

    2017-01-01

    Metal halide perovskites such as methylammonium lead iodide (CH3NH3PbI3) are generating great excitement due to their outstanding optoelectronic properties, which lend them to application in high-efficiency solar cells and light-emission devices. However, there is currently debate over what drives the second-order electron-hole recombination in these materials. Here, we propose that the bandgap in CH3NH3PbI3 has a direct-indirect character. Time-resolved photo-conductance measurements show that generation of free mobile charges is maximized for excitation energies just above the indirect bandgap. Furthermore, we find that second-order electron-hole recombination of photo-excited charges is retarded at lower temperature. These observations are consistent with a slow phonon-assisted recombination pathway via the indirect bandgap. Interestingly, in the low-temperature orthorhombic phase, fast quenching of mobile charges occurs independent of the temperature and photon excitation energy. Our work provides a new framework to understand the optoelectronic properties of metal halide perovskites and analyse spectroscopic data.

  19. Electron–Rotor Interaction in Organic–Inorganic Lead Iodide Perovskites Discovered by Isotope Effects

    Energy Technology Data Exchange (ETDEWEB)

    Gong, Jue; Yang, Mengjin; Ma, Xiangchao; Schaller, Richard D.; Liu, Gang; Kong, Lingping; Yang, Ye; Beard, Matthew C.; Lesslie, Michael; Dai, Ying; Huang, Baibiao; Zhu, Kai; Xu, Tao

    2016-08-04

    We report on the carrier-rotor coupling effect in perovskite organic-inorganic hybrid lead iodide (CH3NH3PbI3) compounds discovered by isotope effects. Deuterated organic-inorganic perovskite compounds including CH3ND3PbI3, CD3NH3PbI3, and CD3ND3PbI3 were synthesized. Devices made from regular CH3NH3PbI3 and deuterated CH3ND3PbI3 exhibit comparable performance in band gap, current-voltage, carrier mobility, and power conversion efficiency. However, a time-resolved photoluminescence (TRPL) study reveals that CH3NH3PbI3 exhibits notably longer carrier lifetime than that of CH3ND3PbI3, in both thin-film and single-crystal formats. Furthermore, the comparison in carrier lifetime between CD3NH3PbI3 and CH3ND3PbI3 single crystals suggests that vibrational modes in methylammonium (MA+) have little impact on carrier lifetime. In contrast, the fully deuterated compound CD3ND3PbI3 reconfirmed the trend of decreasing carrier lifetime upon the increasing moment of inertia of cationic MA+. Polaron model elucidates the electron-rotor interaction.

  20. Crystal growth and characterization of rare earth iodides for scintillation detection

    Science.gov (United States)

    van Loef, E. V.; Higgins, W. M.; Glodo, J.; Churilov, A. V.; Shah, K. S.

    2008-04-01

    In this paper we report on the crystal growth and characterization of a new class of inorganic scintillators based on the rare earth iodides, in particular LuI 3, YI 3 and GdI 3, doped with trivalent cerium. Single crystals of LuI 3:Ce 3+, YI 3:Ce 3+ and GdI 3:Ce 3+ were grown by the vertical Bridgman technique in evacuated silica ampoules. In some cases, tantalum or graphite crucibles were used to minimize wetting of the ampoule. X-ray excited optical luminescence spectra of LuI 3:Ce 3+, YI 3:Ce 3+ and GdI 3:Ce 3+ exhibit a broad band due to Ce 3+ emission, peaking in the 500-550 nm region. LuI 3:Ce 3+, YI 3:Ce 3+ and GdI 3:Ce 3+ show high light yields up to 100,000 photons/MeV and fast principle decay time constants of <40 ns. Energy resolutions measured at 662 keV are of the order of 3.5-9% (FWHM).

  1. 2,3,5-Triphenyl-2H-tetrazol-3-ium iodide

    Directory of Open Access Journals (Sweden)

    Hoong-Kun Fun

    2012-09-01

    Full Text Available The asymmetric unit of the title molecular salt, C19H15N4+·I−, contains four 2,3,5-triphenyl-2H-tetrazol-3-ium cations and five iodide anions, with two of the latter lying on crystallographic inversion centres. In each cation, the tetrazole ring is essentially planar (r.m.s. deviations = 0.004–0.007 Å. The dihedral angles between the tetrazole ring and its three attached benzene rings in the four independent cations are: 12.9 (4, 67.0 (4, 48.1 (4; 20.8 (4, 51.1 (4, 62.3 (4; 11.4 (4, 52.3 (4, 47.3 (4 and 6.0 (4, 85.7 (4, 43.5 (4°. A C—H...I hydrogen bond and C—H...π interactions are observed in the crystal.

  2. Growth and properties of lead iodide thin films by spin coating

    Indian Academy of Sciences (India)

    D ACUÑA; B KRISHNAN; S SHAJI; S SEPÚLVEDA; J L MENCHACA

    2016-10-01

    In this study, lead iodide (PbI$_2$) thin films were deposited on glass substrates by spin coating a solution of 0.2 M PbI$_2$ dissolved in dimethylformamide, varying the deposition time and the spin speed. The thickness of the thin films decreased with increase in spin speed and deposition time, as examined by profilometry measurements.The structure,morphology, optical and electrical properties of the thin films were analysed using various techniques. X-ray diffraction patterns revealed that the thin films possessed hexagonal structures. The thin films were grown highly oriented to [001] direction of the hexagonal lattice. Raman peaks detected at 96 and 136 cm$^{-1}$ were corresponding to the characteristic vibration modes of PbI$_2$. The X-ray photoelectron spectroscopy detected the presence of Pb and I with core level binding energies corresponding to that in PbI2. Atomic force microscopy showed smooth and compact morphology of the thin films. From UV–Vis transmittance and reflectance spectral analysis, the bandgap of the thin films $\\sim$2.3 eV was evaluated. The dark conductivity of the thin films was computed and the value decreased as the deposition time and spin speed increased.

  3. Human sodium iodide symporter (hNIS) in fibroadenoma breast--a immunohistochemical study.

    Science.gov (United States)

    Rai, Ruchi; Shrivastava, Ashutosh; Tandon, Ashwani; Godbole, Madan M; Kumar, Sandeep; Das, Vinita; Dwivedi, Varsha; Pal, Lily

    2011-02-01

    Human sodium iodide symporter (hNIS), responsible for the active transport of iodine is an integral plasma membrane glycoprotein present in the thyroid cells and extrathyroid tissues like breast and salivary glands. If its functional form is unequivocally shown in benign or malignant breast tissues, then it may serve as a basis for diagnosis and treatment using radioactive iodine. With an aim to analyze the hNIS expression in a distinct benign breast condition of fibroadenoma, biopsy proven fibroadenoma tissues, normal non-lactating breast tissue and biopsy proven infiltrating duct carcinoma tissues were examined for hNIS expression using immunohistochemistry. Out of 20 biopsy proven fibroadenoma tissues, 19 (95%) showed positivity for hNIS protein and only one was negative. Of these 10% were mildly positive, 50% cases were moderately positive and 35% showed intense positivity. None of the control tissue obtained from reduction mammoplasty specimens or normal breast tissues samples (5 cms away from the tumor) were positive, hNIS was also intensely positive in 9 out of 10 (90%) infiltrating duct carcinoma tissues and moderately positive in one case. These preliminary results show that hNIS was present in high frequency as demonstrated by immunohistochemistry in fibroadenoma breast.

  4. Fulleropyrrolidinium Iodide As an Efficient Electron Transport Layer for Air-Stable Planar Perovskite Solar Cells.

    Science.gov (United States)

    Huang, Jiabin; Yu, Xuegong; Xie, Jiangsheng; Li, Chang-Zhi; Zhang, Yunhai; Xu, Dikai; Tang, Zeguo; Cui, Can; Yang, Deren

    2016-12-21

    Organic-inorganic halide perovskite solar cells have attracted great attention in recent years. But there are still a lot of unresolved issues related to the perovskite solar cells such as the phenomenon of anomalous hysteresis characteristics and long-term stability of the devices. Here, we developed a simple three-layered efficient perovskite device by replacing the commonly employed PCBM electrical transport layer with an ultrathin fulleropyrrolidinium iodide (C60-bis) in an inverted p-i-n architecture. The devices with an ultrathin C60-bis electronic transport layer yield an average power conversion efficiency of 13.5% and a maximum efficiency of 15.15%. Steady-state photoluminescence (PL) and time-resolved photoluminescence (TRPL) measurements show that the high performance is attributed to the efficient blocking of holes and high extraction efficiency of electrons by C60-bis, due to a favorable energy level alignment between the CH3NH3PbI3 and the Ag electrodes. The hysteresis effect and stability of our perovskite solar cells with C60-bis become better under indoor humidity conditions.

  5. The effect of tanespimycin (17-AAG) on radioiodine accumulation in sodium iodide symporter expressing cells

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Kyoung Hyun; Youn, Hyewon; Song, Myung Geun; Lee, Dong Soo; Chung, June Key [Seoul National Univ. College of Medicine, Seoul (Korea, Republic of)

    2012-12-15

    The heat shock protein 90 inhibitor, tanespimycin, is an anticancer agent known to increase iodine accumulation in normal and cancerous thyroid cells. Iodine accumulation is regulated by membrane proteins such as sodium iodide sym porter (NIS) and pendrin (PDS), and thus we attempted to characterize the effects of tanespimycin on those genes. Cells were incubated with tanespimycin in order to evaluate {sup 125}I accumulation and efflux ability. Radioiodine uptake and efflux were measured by a gamma counter and normalized by protein amount. RT PCR were performed to measure the level of gene expression. After tanespimycin treatment, {sup 125}uptake was in creased by {approx}2.5 fold in FRTL 5, hNIS ARO. and hNIS MDA MB 231 cells, but no changes were detected in the hNIS HeLa cells. Tanespimycin significantly reduced the radioiodine efflux rate only in the FRTL 5 cell. in the FRTL 5 and hNIS ARO cells, PDS mRNA levels were markedly reduced; the only other observed alteration in the levels of NIS mRNA after tanespimtycin treatment was an observed increase in the h hNIS ARO cells. These results indicate that cellular responses against tanespimycin treatment differed between the normal rat thyroid cells and human cancer cells, and the reduction in the {sup 125I} efflux rate by tanespimycin in the normal rat thyroid cells might be attributable to reduced PDS gene expression.

  6. Structures, Phase Transitions and Tricritical Behavior of the Hybrid Perovskite Methyl Ammonium Lead Iodide

    Science.gov (United States)

    Whitfield, P. S.; Herron, N.; Guise, W. E.; Page, K.; Cheng, Y. Q.; Milas, I.; Crawford, M. K.

    2016-01-01

    We have examined the crystal structures and structural phase transitions of the deuterated, partially deuterated and hydrogenous organic-inorganic hybrid perovskite methyl ammonium lead iodide (MAPbI3) using time-of-flight neutron and synchrotron X-ray powder diffraction. Near 330 K the high temperature cubic phases transformed to a body-centered tetragonal phase. The variation of the order parameter Q for this transition scaled with temperature T as Q ∼ (Tc−T)β, where Tc is the critical temperature and the exponent β was close to ¼, as predicted for a tricritical phase transition. However, we also observed coexistence of the cubic and tetragonal phases over a range of temperature in all cases, demonstrating that the phase transition was in fact first-order, although still very close to tricritical. Upon cooling further, all the tetragonal phases transformed into a low temperature orthorhombic phase around 160 K, again via a first-order phase transition. Based upon these results, we discuss the impact of the structural phase transitions upon photovoltaic performance of MAPbI3 based solar cells. PMID:27767049

  7. Effectiveness of potassium iodide in the treatment of GERD patients in combination with iodine deficiency states

    Directory of Open Access Journals (Sweden)

    V. B. Boychuk

    2015-04-01

    Full Text Available GERD and iodine deficiency conditions are not only limited by similar clinical symptoms. They influence on each other by regulatory kinetic mechanisms of upper gastrointestinal tract. Aim. We examined 40 patients with GERD on a background of iodine deficiency in order to study the efficacy of using potassium iodide in these patients. Methods and results. Iodine deficiency was detected by level of iodine in urine, level of TSH, free T4 and free T3. Also was determined motor-evacuational function of the stomach according to 13C-octanoic breath test and levels of regulatory peptides (gastrin, cholecystokinin-pankreozymin and pepsinogens. Conclusion. Positive dynamics of iodine absorption and motor-evacuational function of the stomach were found after 1 month of treatment. Decreasing frequency and duration of acid reflux and reducing pepsinogen levels and improvement of indicators of intestinal hormones were also found in these patiens. This shows the optimization of regulatory mechanisms and kinetics of upper gastrointestinal tract.

  8. Association of itraconazole and potassium iodide in the treatment of feline sporotrichosis: a prospective study.

    Science.gov (United States)

    Reis, Érica G; Schubach, Tânia M P; Pereira, Sandro A; Silva, Jéssica N; Carvalho, Beatriz W; Quintana, Marcel S B; Gremião, Isabella D F

    2016-10-01

    Feline sporotrichosis is an endemic disease in Rio de Janeiro, Brazil, where zoonotic transmission of Sporothrix spp. has been reported since 1998. Itraconazole (ITZ) remains the first choice for treating this disease in cats. However, there have been reports of therapeutic failure and a long-term endeavor. Potassium iodide (KI), considered in the past as a drug with variable effectiveness in cats with sporotrichosis, arises as an important option in the treatment of cats from the endemic area of Rio de Janeiro. In order to evaluate the effectiveness of the association of ITZ and KI in naive cats with sporotrichosis, a prospective cohort study was conducted on 30 cats receiving ITZ 100 mg/day and KI 2.5 mg-20 mg/kg/day. Clinical and laboratory adverse effects were assessed once a month according to the standard care protocol. The cure rate was 96.15% within a median of 14 weeks of treatment. Adverse effects were observed in 50% of cats and were managed with a temporary drug suspension and/or a hepatoprotective therapy. The association of ITZ and KI emerges as an effective option for the treatment of feline sporotrichosis.

  9. Determination of iodide using flow injection with acidic potassium permanganate chemiluminescence detection.

    Science.gov (United States)

    Yaqoob, Mohammad; Atiq-ur-Rehman; Waseem, Amir; Nabi, Abdul

    2006-01-01

    A simple and rapid flow-injection method is described for the determination of iodide, based on potassium permanganate chemiluminescence detection via oxidation of formaldehyde in aqueous hydrochloric acid. The calibration graph was linear over the range 1.0-12 x 10(-6) mol/L (r2 = 0.9955) with relative standard deviations (n = 4) in the range 1.0-3.5%. The detection limit (3sigma) was 1.0 x 10(-7) mol/L, with sample throughput of 120/h. The effect of interfering cations [Ca(II), Mg(II), Ni(II), Fe(II), Fe(III) and Pb(II)] and anions (Cl-, SO4(2-), PO4(3-), NO3-, NO2-, F- and SO3(2-)) were studied. The method was applied to iodized salt samples and the results obtained in the range 0.03 +/- 0.005 - 0.10 +/- 0.006 mg I/g were in reasonable agreement with the amount labelled. The method was statistically compared with the results obtained by titration; no significant disagreement at 95% confidence was observed.

  10. Quick staining technique for myeloperoxidase using potassium iodide and oxidized pyronine B.

    Science.gov (United States)

    Chen, Wan-Xin; Zhu, Hong-Lin; Xue, Mei; Zhou, Hao; Zhao, Fei; Yan, Ni; Chen, Yan

    2014-01-01

    Myeloperoxidase (MPO) staining has been important for the cytomorphological diagnosis and classification of leukemia. A novel staining method for MPO and its clinical application are presented in the report. Pyronine B (PyB), serving as a chromogenic reagent, was pre-oxidized to obtain stable oxidized Pyronine B solution. The MPO working solution for oxidized pyronine B method consisted of phosphate buffer solution, potassium iodide (KI) solution, and oxidized Pyronine B solution. The positive products of the oxidized Pyronine B method of MPO staining were vibrant red particles located in cytoplasm and the nucleus was stained bluish green. Bone marrow smears from 229 patients with acute leukemia or with grossly normal bone marrow were stained by both oxidized Pyronine B method and the conventional Washburn benzidine staining and a comparison revealed no significant difference in the positive detection rate between the two techniques. The new method eliminates the influence of the varying amount of H₂O₂ on MPO staining. With this method, the reagents were more stable and the staining procedure was simple and time-saving. This MPO staining technique is a better alternative than the conventional benzidine-based methods.

  11. Potassium Iodide-Functionalized Polyaniline Nanothin Film Chemiresistor for Ultrasensitive Ozone Gas Sensing

    Directory of Open Access Journals (Sweden)

    Sira Srinives

    2017-02-01

    Full Text Available Polyaniline (PANI nanostructures have been widely studied for their sensitivity to atmospheric pollutants at ambient conditions. We recently showed an effective way to electropolymerize a PANI nanothin film on prefabricated microelectrodes, and demonstrated its remarkable sensing performance to be comparable to that of a one-dimensional nanostructure, such as PANI nanowires. In this work, we report further progress in the application of the PANI nanothin film chemiresistive sensor for the detection of ozone (O3 by modifying the film with potassium iodide (KI. The KI-PANI sensor exhibited an excellent sensitivity to O3 (8–180 ppb O3 concentration rage with a limit of detection of 230 ppt O3, and exquisite selectivity against active chemicals such as nitrogen dioxide (NO2 and sulfur dioxide (SO2. The sensing mechanism of the sensor relied on iodometric chemistry of KI and O3, producing triiodide ( I 3 − that partially doped and increased electrical conductivity of the PANI film. The sensitivity and selectivity of the KI-functionalized PANI film demonstrates the potential use for KI-PANI-based O3 sensing devices in environmental monitoring and occupational safety.

  12. Growth and characterization of NLO crystal: L-leucine phthalic acid potassium iodide

    Directory of Open Access Journals (Sweden)

    Jagadeesh M.R.

    2015-09-01

    Full Text Available A new semi-organic non linear optical crystal, L-leucine phthalic acid potassium iodide (LLPPI has been grown from an aqueous solution by slow evaporation method. The grown crystals were subjected to different characterizations, such as single crystal XRD, FT-IR, UV-Vis, TGA, SEM, EDAX, micro hardness, dielectric and powder SHG. Single crystal structure was determined from X-ray diffraction data and it revealed that the crystal belongs to triclinic system with the space group P1. The vibrational frequencies of various functional groups were derived from FT-IR spectrum. Thermal stability of the grown crystal was investigated by TG-DTA studies and it was observed that the crystal was thermally stable up to 192 °C. Optical absorption study was carried out and a good transparency in the entire visible region was observed at the lower cutoff wavelength of 227 nm. Dielectric study was performed as a function of frequency and normal dielectric behavior was observed. The micro hardness test was carried out and the load dependent hardness was measured. Kurtz powder method was employed to explore the NLO characteristics of the grown crystal.

  13. FEASIBILITY STUDY FOR POTASSIUM IODIDE (KI) DISTRIBUTION IN NEW YORK CITY.

    Energy Technology Data Exchange (ETDEWEB)

    MOSS, STEVEN

    2005-04-29

    The New York City Department of Health and Mental Hygiene (DOHMH), Bureau of Environmental Science and Engineering, Office of Radiological Health (ORH) [as the primary local technical consultant in the event of a radiological or nuclear incident within the boundaries of New York City] requested the assistance of Brookhaven National Laboratory (BNL) with the development of a Feasibility Study for Potassium Iodide (KI) distribution in the unlikely event of a significant release of radioactive iodine in or near New York City. Brookhaven National Laboratory had previously provided support for New York City with the development of the radiological/nuclear portions of its All Hazards Emergency Response Plans. The work is funded by Medical and Health Research Association (MHRA) of New York City, Inc., under a work grant by the Federal Centers for Disease Control (CDC) for Public Health Preparedness and Response for Bioterrorism. This report is part of the result of that effort. The conclusions of this report are that: (1) There is no credible radiological scenario that would prompt the need for large segments of the general population of New York City to take KI as a result of a projected plume exposure to radioiodine reaching even the lowest threshold of 5 rem to the thyroid; and (2) KI should be stockpiled in amounts and locations sufficient for use by first responders/emergency responders in response to any localized release of radioiodine.

  14. The kinetics of iodide oxidation by the manganese oxide mineral birnessite

    Science.gov (United States)

    Fox, P.M.; Davis, J.A.; Luther, G. W.

    2009-01-01

    The kinetics of iodide (I-) and molecular iodine (I2) oxidation by the manganese oxide mineral birnessite (??-MnO2) was investigated over the pH range 4.5-6.25. I- oxidation to iodate (IO3-) proceeded as a two-step reaction through an I2 intermediate. The rate of the reaction varied with both pH and birnessite concentration, with faster oxidation occurring at lower pH and higher birnessite concentration. The disappearance of I- from solution was first order with respect to I- concentration, pH, and birnessite concentration, such that -d[I-]/dt = k[I-][H+][MnO2], where k, the third order rate constant, is equal to 1.08 ?? 0.06 ?? 107 M-2 h-1. The data are consistent with the formation of an inner sphere I- surface complex as the first step of the reaction, and the adsorption of I- exhibited significant pH dependence. Both I2, and to a lesser extent, IO3- sorbed to birnessite. The results indicate that iodine transport in mildly acidic groundwater systems may not be conservative. Because of the higher adsorption of the oxidized I species I2 and IO3-, as well as the biophilic nature of I2, redox transformations of iodine must be taken into account when predicting I transport in aquifers and watersheds.

  15. Advanced Raman Spectroscopy of Methylammonium Lead Iodide: Development of a Non-destructive Characterisation Methodology

    Science.gov (United States)

    Pistor, Paul; Ruiz, Alejandro; Cabot, Andreu; Izquierdo-Roca, Victor

    2016-10-01

    In recent years, there has been an impressively fast technological progress in the development of highly efficient lead halide perovskite solar cells. However, the stability of perovskite films and respective solar cells is still an open point of concern and calls for advanced characterization methods. In this work, we identify appropriate measurement conditions for a meaningful analysis of spin-coated absorber-grade perovskite thin films based on methylammonium (MA) lead iodide (MAPbI3) by Raman spectroscopy. The material under investigation and its derivates is the most commonly used for high efficiency devices in the literatures and has yielded working solar cell devices with efficiencies around 10% in our laboratory. We report highly detailed Raman spectra obtained with excitation at 532 nm and 633 nm and their deconvolution taking advantage of the simultaneous fitting of spectra obtained with varying excitation wavelengths. Finally, we propose a fast and contactless methodology based on Raman to probe composition variations and/or degradation of these perovskite thin films and discuss the potential of the presented technique as quality control and degradation monitoring tool in other organic-inorganic perovskite materials and complete solar cell devices.

  16. Highly spin-polarized deuterium atoms from the UV dissociation of Deuterium Iodide

    CERN Document Server

    Sofikitis, D; Koumarianou, G; Jiang, H; Bougas, L; Samartzis, P C; Andreev, A; Rakitzis, T P

    2016-01-01

    Hyperpolarisation of deuterium (D) and tritium (T) nuclear spins increases the D-T fusion reaction rate by ~50%, thus lowering the breakeven limit for the achievement of self-sustained fusion, and controls the emission direction of the reaction products for improved reactor efficiency. However, the important D-D polarization-dependent fusion reaction has not yet been measured, due to the low density of conventional polarized deuterium beams of ~10$^{12}$ cm$^{-3}$, limited by collisions on the ms-timescale of production. Here we demonstrate that hyperpolarised D atoms are produced by the 270 nm photodissociation of deuterium iodide (DI), yielding ~60% nuclear D polarization after ~1.6 ns, ~10$^6$ times faster than conventional methods, allowing collision-limited densities of ~10$^{18}$ cm$^{-3}$. Such ultrahigh densities of polarized D atoms open the way for the study of high-signal polarized D-D reactions. We discuss the possibility of the production of high-density pulsed polarized beams, and of polarized D...

  17. Efficient methylammonium lead iodide perovskite solar cells with active layers from 300 to 900 nm

    Energy Technology Data Exchange (ETDEWEB)

    Momblona, C.; Malinkiewicz, O.; Soriano, A.; Gil-Escrig, L.; Bandiello, E.; Scheepers, M.; Bolink, H. J., E-mail: henk.bolink@uv.es [Instituto de Ciencia Molecular, Universidad de Valencia, C/Catedrático J. Beltrán 2, 46980 Paterna, Valencia (Spain); Roldán-Carmona, C. [Instituto de Ciencia Molecular, Universidad de Valencia, C/Catedrático J. Beltrán 2, 46980 Paterna, Valencia (Spain); Department of Physical Chemistry and Applied Thermodynamics, University of Córdoba, Campus Rabanales, Ed. C3, 14014, Córdoba (Spain); Edri, E. [Department of Materials and Interfaces, Weizmann Institute of Science, Herzl St. 34, Rehovot 76100 (Israel)

    2014-08-01

    Efficient methylammonium lead iodide perovskite-based solar cells have been prepared in which the perovskite layer is sandwiched in between two organic charge transporting layers that block holes and electrons, respectively. This configuration leads to stable and reproducible devices that do not suffer from strong hysteresis effects and when optimized lead to efficiencies close to 15%. The perovskite layer is formed by using a dual-source thermal evaporation method, whereas the organic layers are processed from solution. The dual-source thermal evaporation method leads to smooth films and allows for high precision thickness variations. Devices were prepared with perovskite layer thicknesses ranging from 160 to 900 nm. The short-circuit current observed for these devices increased with increasing perovskite layer thickness. The main parameter that decreases with increasing perovskite layer thickness is the fill factor and as a result optimum device performance is obtained for perovskite layer thickness around 300 nm. However, here we demonstrate that with a slightly oxidized electron blocking layer the fill factor for the solar cells with a perovskite layer thickness of 900 nm increases to the same values as for the devices with thin perovskite layers. As a result the power conversion efficiencies for the cells with 300 and 900 nm are very similar, 12.7% and 12%, respectively.

  18. Low band gap polymeric solar cells using solution-processable copper iodide as hole transporting layer

    Science.gov (United States)

    Chaudhary, Neeraj; Kesari, J. P.; Chaudhary, Rajiv; Patra, Asit

    2016-08-01

    In the present work, we have shown the performance of solution-processable copper iodide (CuI) as an alternative hole transporting layer (HTL) for polymeric solar cells. Optical spectra of the CuI thin film reveal highly transparent and practically no absorption in the range vis-NIR region (450-1110 nm). X-ray diffraction (XRD) patterns of CuI exhibits as a p-type semiconductor as well as crystalline nature. The photovoltaic devices were fabricated using PCDTBT and PTB7 as donor materials blended with PC71BM as an acceptor material. The power conversion efficiencies (PCEs) based on CuI as an HTL have been achieved to up to 3.04% and 4.48% for PCDTBT and PTB7 based donor materials respectively with a configuration based on ITO/CuI(40 nm)/active layer (60 nm)/Al (120 nm). This study clearly indicated that the devices made with CuI as an HTL showed superior performance than the device fabricated from PEDOT:PSS layer as an HTL. Morphological characterization of the HTL using scanning electron microscopy (SEM) and atomic force microscope (AFM) were carried for better understanding.

  19. Perfluorooctyl Iodide Stimulates Steroidogenesis in H295R Cells via a Cyclic Adenosine Monophosphate Signaling Pathway.

    Science.gov (United States)

    Wang, Chang; Ruan, Ting; Liu, Jiyan; He, Bin; Zhou, Qunfang; Jiang, Guibin

    2015-05-18

    Perfluorinated iodine alkanes (PFIs) are used widely in the organic fluorine industry. Increased production of PFIs has caused environmental health concerns. To evaluate the potential endocrine-disrupting effect of PFIs, we investigated the effects of perfluorooctyl iodide (PFOI) on steroidogenesis in human adrenocortical carcinoma cells (H295R). Levels of aldosterone, cortisol, 17β-estradiol, and testosterone were measured in H295R culture medium upon treatment with perfluorooctanoic acid (PFOA) and PFIs. Expression of 10 steroidogenic genes (StAR, HMGR, CYP11A1, 3βHSD2, 17βHSD, CYP17, CYP21, CYP11B1, CYP11B2, and CYP19) was measured by real-time polymerase chain reaction. Levels of cyclic adenosine monophosphate (cAMP) and adenylate cyclase (AC) activity were measured to understand the underlying mechanism of steroidogenic perturbations. Levels of production of aldosterone, cortisol, and 17β-estradiol were elevated significantly, and the level of testosterone generation decreased upon treatment with 100 μM PFOI. Similar to the effect induced by forskolin (AC activator), expression of all 10 genes involved in the synthesis of steroid hormones was upregulated significantly upon exposure to 100 μM PFOI. PFOA had no effect on steroid hormone production or steroidogenic gene expression even though it is highly structurally similar with PFOI. Therefore, the terminal -CF2I group in PFOI could be a critical factor for mediation of steroidogenesis. PFOI increased AC activity and cAMP levels in H295R cells, which implied an underlying mechanism for the disturbance of steroidogenesis. These data suggest that PFOI may act as an AC activator, thereby stimulating steroidogenesis by activating a cAMP signaling pathway.

  20. New hybrid lead iodides: From one-dimensional chain to two-dimensional layered perovskite structure

    Energy Technology Data Exchange (ETDEWEB)

    Xiong, Kecai; Liu, Wei [Department of Chemistry and Chemical Biology, Rutgers University, 610 Taylor Road, Piscataway, NJ 08854 (United States); Teat, Simon J. [Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); An, Litao; Wang, Hao; Emge, Thomas J. [Department of Chemistry and Chemical Biology, Rutgers University, 610 Taylor Road, Piscataway, NJ 08854 (United States); Li, Jing, E-mail: jingli@rutgers.edu [Department of Chemistry and Chemical Biology, Rutgers University, 610 Taylor Road, Piscataway, NJ 08854 (United States)

    2015-10-15

    Two new hybrid lead halides (H{sub 2}BDA)[PbI{sub 4}] (1) (H{sub 2}BDA=1,4-butanediammonium dication) and (HNPEIM)[PbI{sub 3}] (2) (HNPEIM=N-​phenyl-ethanimidamidine cation) have been synthesized and structurally characterized. X-ray diffraction analyses reveal that compound 1 features a two-dimensional corner-sharing perovskite layer whereas compound 2 contains one-dimensional edge-sharing double chains. The N-​phenyl-ethanimidamidine cation within compound 2 was generated in-situ under solvothermal conditions. The optical absorption spectra collected at room temperature suggest that both compounds are semiconductors having direct band gaps, with estimated values of 2.64 and 2.73 eV for 1 and 2, respectively. Results from the density functional theory (DFT) calculations are consistent with the experimental data. Density of states (DOS) analysis reveals that in both compounds 1 and 2, the energy states in the valence band maximum region are iodine 5p atomic orbitals with a small contribution from lead 6s, while in the region of conduction band minimum, the major contributions are from the inorganic (Pb 6p atomic orbitals) and organic components (C and N 2p atomic orbitals) in compound 1 and 2, respectively. - Graphical abstract: Two new hybrid lead halides built on one-dimensional edge-sharing double chains and two-dimensional corner-sharing perovskite layers are synthesized and their structural and electronic properties are analyzed. - Highlights: • Two new hybrid lead iodides are designed, synthesized, and characterized. • They are closely related to, but different from, perovskite structures. • The electronic properties of both compounds are analyzed by DFT calculations.

  1. Impact of Atomic Structure on Absolute Energy Levels of Methylammonium Lead Iodide Perovskite

    Science.gov (United States)

    Choi, Joshua

    2015-03-01

    There has been a staggeringly rapid increase in the photovoltaic performance of methylammonium lead iodide (MAPbI3) perovskite - greater than 19 percent solar cell power conversion efficiency has been reported in less than five years since the first report in 2009. Despite the progress in device performance, structure-property relationships in MAPbI3 are still poorly understood. I will present our recent findings on the impact of changing the Pb-I bond length and Pb-I-Pb bond angle on the electronic structure of MAPbI3. By using the combination of temperature dependent X-ray scattering, ultraviolet photoelectron spectroscopy, absorbance and PL spectroscopy, we show that the energy levels of highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) shift in the same direction as MAPbI3 goes through tetragonal-to-cubic structural phase transition wherein the rotational angle of PbI6 octahedra is the order parameter of the transition. Our experimental results are corroborated by density functional theory calculations which show that the lattice expansion and bond angle distortion cause different degree of orbital overlap between the Pb and I atoms and the anti-bonding orbital nature of both HOMO and LUMO results in the same direction of their shift. Moreover, through pair distribution function analysis of X-ray scattering, we discovered that the majority of MAPbI3 in thin film solar cell layer has highly disordered structure with a coherence range of only 1.4 nm. The nanostructuring correlates with a blueshift of the absorption onset and increases the photoluminescence. Our results underscore the importance of understanding the structure-property relationships in order to improve the device performance of metal-organic perovskites.

  2. Remediation of methyl iodide in aqueous solution and soils amended with thiourea.

    Science.gov (United States)

    Zheng, Wei; Papiernik, Sharon K; Guo, Mingxin; Yates, Scott R

    2004-02-15

    Methyl iodide (MeI) is considered a very promising fumigant alternative to methyl bromide (MeBr) for controlling soil-borne pests. Because atmospheric emission of highly volatile fumigants contributes to air pollution, feasible strategies to reduce emissions are urgently needed. In this study, thiourea (a nitrification inhibitor) was shown to accelerate the degradation of MeI in soil and water. In aqueous solution, the reaction between MeI and thiourea was independent of pH, although the rate of MeI hydrolysis increased in alkaline solution. Substantial increases in the rate of MeI dissipation were observed in thiourea-amended soils. Transformation of MeI by thiourea in aqueous solution was by a single chemical reaction process, while MeI degradation in thiourea-amended soil apparently involved a catalytic mechanism. The electron delocalization between the thiourea molecule and the surfaces of soil particles is energetically favorable and would increase the nucleophilic reactivity of the thiono group toward MeI, resulting in an enhancement of the dissipation rate. The soil half-life for MeI was reduced from >300 h for unamended soils to only a few hours in soil or sand amended with thiourea at a 2:1 molar ratio (thiourea:MeI). The MeI transformation rate in thiourea-amended soil increased with increasing soil temperature and decreasing soil moisture. Therefore, spraying thiourea on the soil surface to form a "reactive surface barrier" may be an effective and innovative strategy for controlling fumigant emissions to the atmosphere and for improving environmental protection.

  3. Parametric studies of radiolytic oxidation of iodide solutions with and without paint: comparison with code calculations

    Energy Technology Data Exchange (ETDEWEB)

    Poletiko, C.; Hueber, C. [Inst. de Protection et de Surete Nucleaire, C.E. Cadarache, St. Paul-lez-Durance (France); Fabre, B. [CISI, C.E. Cadarache, St. Paul-lez-Durance (France)

    1996-12-01

    In case of severe nuclear accident, radioactive material may be released into the environment. Among the fission products involved, are the very volatile iodine isotopes. However, the chemical forms are not well known due to the presence of different species in the containment with which iodine may rapidly react to form aerosols, molecular iodine, hydroiodic acid and iodo-organics. Tentative explanations of different mechanisms were performed through benchscale tests. A series of tests has been performed at AEA Harwell (GB) to study parameters such as pH, dose rate, concentration, gas flow rate, temperature in relation to molecular iodine production, under dynamic conditions. Another set of tests has been performed in AECL Whiteshell (CA) to study the behaviour of painted coupons, standing in gas phase or liquid phase or both, with iodine compounds under radiation. The purpose of our paper is to synthesize the data and compare the results to the IODE code calculation. Some parameters of the code were studied to fit the experimental result the best. A law, concerning the reverse reaction of iodide radiolytic oxidation, has been proposed versus: pH, concentrations and gas flow-rate. This law does not apply for dose rate variations. For the study of painted coupons, it has been pointed out that molecular iodine tends to be adsorbed or chemically absorbed on the surface in gas phase, but the mechanism should be more sophisticated in the aqueous phase. The iodo-organics present in liquid phase tend to be partly or totally destroyed by oxidation under radiation (depending upon the dose delivered). These points are discussed. (author) 18 figs., 3 tabs., 15 refs.

  4. Photodetectors Based on Two-Dimensional Layer-Structured Hybrid Lead Iodide Perovskite Semiconductors.

    Science.gov (United States)

    Zhou, Jiachen; Chu, Yingli; Huang, Jia

    2016-10-05

    Hybrid lead iodide perovskite semiconductors have attracted intense research interests recently because of their easy fabrication processes and high power conversion efficiencies in photovoltaic applications. Layer-structured materials have interesting properties such as quantum confinement effect and tunable band gap due to the unique two-dimensional crystalline structures. ⟨100⟩-oriented layer-structured perovskite materials are inherited from three-dimensional ABX3 perovskite materials with a generalized formula of (RNH3)2(CH3NH3)n-1MnX3n+1, and adopt the Ruddlesden-Popper type crystalline structure. Here we report the synthesis and investigation of three layer-structured perovskite materials with different layer numbers: (C4H9NH3)2PbI4 (n = 1, one-layered perovskite), (C4H9NH3)2(CH3NH3)Pb2I7 (n = 2, two-layered perovskite) and (C4H9NH3)2(CH3NH3)2Pb3I10 (n = 3, three-layered perovskite). Their photoelectronic properties were investigated in related to their molecular structures. Photodetectors based on these two-dimensional (2D) layer-structured perovskite materials showed tunable photoresponse with short response time in milliseconds. The photodetectors based on three-layered perovskite showed better performances than those of the other two devices, in terms of output current, responsivity, Ilight/Idark ratio, and response time, because of its smaller optical band gap and more condensed microstructure comparing the other two materials. These results revealed the relationship between the molecular structures, film microstructures and the photoresponse properties of 2D layer-structured hybrid perovskites, and demonstrated their potentials as flexible, functional, and tunable semiconductors in optoelectronic applications, by taking advantage of their tunable quantum well molecular structure.

  5. Dimethyl phenyl piperazine iodide (DMPP) induces glioma regression by inhibiting angiogenesis

    Energy Technology Data Exchange (ETDEWEB)

    He, Yan-qing; Li, Yan; Wang, Xiao-yu [Key Laboratory for Regenerative Medicine of the Ministry of Education, Division of Histology and Embryology, Medical College, Jinan University, Guangzhou 510632 (China); He, Xiao-dong [Institute of Vascular Biological Sciences, Guangdong Pharmaceutical University, Guangzhou 510006 (China); Jun, Li [Guangdong Provincial Key Laboratory of Bioengineering Medicine, National Engineering Research Centre of Genetic Medicine, College of Life Science and Technology, Jinan University, Guangzhou 510632 (China); Chuai, Manli [Division of Cell and Developmental Biology, University of Dundee, Dundee, DD1 5EH (United Kingdom); Lee, Kenneth Ka Ho [Key Laboratory for Regenerative Medicine of the Ministry of Education, School of Biomedical Sciences, Chinese University of Hong Kong, Shatin (Hong Kong); Wang, Ju [Guangdong Provincial Key Laboratory of Bioengineering Medicine, National Engineering Research Centre of Genetic Medicine, College of Life Science and Technology, Jinan University, Guangzhou 510632 (China); Wang, Li-jing, E-mail: wanglijing62@163.com [Institute of Vascular Biological Sciences, Guangdong Pharmaceutical University, Guangzhou 510006 (China); Yang, Xuesong, E-mail: yang_xuesong@126.com [Key Laboratory for Regenerative Medicine of the Ministry of Education, Division of Histology and Embryology, Medical College, Jinan University, Guangzhou 510632 (China)

    2014-01-15

    1,1-Dimethyl-4-phenyl piperazine iodide (DMPP) is a synthetic nicotinic acetylcholine receptor (nAChR) agonist that could reduce airway inflammation. In this study, we demonstrated that DMPP could dramatically inhibit glioma size maintained on the chick embryonic chorioallantoic membrane (CAM). We first performed MTT and BrdU incorporation experiments on U87 glioma cells in vitro to understand the mechanism involved. We established that DMPP did not significantly affect U87 cell proliferation and survival. We speculated that DMPP directly caused the tumor to regress by affecting the vasculature in and around the implanted tumor on our chick CAM model. Hence, we conducted detailed analysis of DMPP's inhibitory effects on angiogenesis. Three vasculogenesis and angiogenesis in vivo models were used in the study which included (1) early chick blood islands formation, (2) chick yolk-sac membrane (YSW) and (3) CAM models. The results revealed that DMPP directly suppressed all developmental stages involved in vasculogenesis and angiogenesis – possibly by acting through Ang-1 and HIF-2α signaling. In sum, our results show that DMPP could induce glioma regression grown on CAM by inhibiting vasculogenesis and angiogenesis. - Highlights: ●We demonstrated that DMPP inhibited the growth of glioma cells on chick CAM. ●DMPP did not significantly affect the proliferation and survival of U87 cells. ●We revealed that DMPP suppressed vasculogenesis and angiogenesis in chick embryo. ●Angiogenesis in chick CAM was inhibited by DMPP via most probably Ang-1 and HIF-2α. ●DMPP could be potentially developed as an anti-tumor drug in the future.

  6. A comparison of the use of sodium iodide and lanthanum bromide scintillation crystals for airborne surveys

    Science.gov (United States)

    Bailey, Derek M.

    The Environmental Protection Agency (EPA) Aerial Spectral Environmental Collection Technology (ASPECT) program performs aerial radiological and chemical characterization of geographical regions of interest. Airborne surveys are performed to characterize environmental radionuclide content, for mineral exploration, as well as for emergency scenarios such as major releases or lost sources. Two radiological detection systems are used by the ASPECT team for gamma-ray detection and characterization: lanthanum bromide [LaBr 3(Ce)] and sodium iodide [NaI(Tl)] scintillation systems. An aerial survey of a uranium mine in the western United States was performed using both NaI(Tl) and LaBr3(Ce) detection systems. Analyses of the survey data were performed with RadAssist software and applying International Atomic Energy Agency (IAEA) airborne gamma ray mapping guidelines. The data for the survey were corrected for cross-over, which is spectral interference from higher energy photons as a result of Compton scattering, height attenuation, cosmic ray contribution to signal, and Radon contribution to signal. Two radiation survey contours were generated from each discrete data set. Based on analysis of the uranium mine survey results, LaBr3(Ce) produced a product comparable to that of NaI(Tl). The LaBr3(Ce) detection system contained 1/16th the scintillating volume and had a total system weight that was 1/4th that of the NaI(Tl) system. LaBr3(Ce) demonstrated a clear advantage over NaI(Tl) detectors in system mobility, and weight factors in airborne gamma ray spectroscopy.

  7. Membrane-based assay for iodide ions based on anti-leaching of gold nanoparticles.

    Science.gov (United States)

    Shen, Yu-Wei; Hsu, Pang-Hung; Unnikrishnan, Binesh; Li, Yu-Jia; Huang, Chih-Ching

    2014-02-26

    We report a label-free colorimetric strategy for the highly selective and sensitive detection of iodide (I(-)) ions in human urine sample, seawater and edible salt. A poly(N-vinyl-2-pyrrolidone)-stabilized Au nanoparticle (34.2-nm) was prepared to detect I(-) ions using silver (Ag(+)) and cyanide (CN(-)) ions as leaching agents in a glycine-NaOH (pH 9.0) solution. For the visual detection of the I(-) ions by naked eye, and for long time stability of the probe, Au nanoparticles (NPs) decorated mixed cellulose ester membrane (MCEM) was prepared (Au NPs/MCEM). The Au NPs-based probe (CN(-)/Ag(+)-Au NPs/MCEM) operates on the principle that Ag(+) ions form a monolyar silver atoms/ions by aurophilic/argentophilic interactions on the Au NPs and it accelerates the leaching rate of Au atoms in presence of CN(-) ions. However, when I(-) is introduced into this system, it inhibits the leaching of Au atoms because of the strong interactions between Ag/Au ions and I(-) ions. Inductively coupled plasma mass spectrometry, surface-assisted laser desorption/ionization time-of-flight mass spectrometry were used to characterize the surface properties of the Au NPs in the presence of Ag(+) and I(-). Under optimal solution conditions, the CN(-)/Ag(+)-Au NPs/MCEM probe enabled the detection of I(-) by the naked eye at nanomolar concentrations with high selectivity (at least 1000-fold over other anions). In addition, this cost-effective probe allowed the determination of I(-) ions in complex samples, such as urine, seawater, and edible salt samples.

  8. Novel bismuth tri-iodide nanostructures obtained by the hydrothermal method and electron beam irradiation

    Science.gov (United States)

    Aguiar, Ivana; Olivera, Alvaro; Mombrú, Maia; Bentos Pereira, Heinkel; Fornaro, Laura

    2017-01-01

    Bismuth tri-iodide is a layered compound semiconductor which has suitable properties as material for ionizing radiation detection devices. Monocrystals and polycrystalline thin films have been studied for this application, but only recently, the development of nanostructures of this compound has emerged as an interesting alternative for using such nanostructures in new types of radiation detectors or for including them in other applications. Considering this, we present in this work BiI3 nanoparticles successfully synthesized by the hydrothermal method, using a Teflon-lined stainless steel autoclave, at a temperature of 180 °C during 8-20 h, with BiCl3 and NaI as source materials. We characterized the nanoparticles by X-ray diffraction (XRD), transmission electron microscopy (TEM) and electron dispersive spectroscopy (EDS). We obtained small rounded or hexagonal particles (10-20 nm in size) and larger structures. The maximum orientation of the nanostructures is along the (0 0 l) family planes and occurs after 16 h of synthesis, which arises as the best condition for obtaining BiI3 oriented nanostructures. When a 100 kV TEM electron beam was converged on the larger structures, we obtained highly oriented BiI3 hexagonal and rod shaped nanostructures. We found that particles' shape does not depend on the synthesis time. In addition, results were compared with the ones obtained for nanoparticles synthesized from solution. The present work is an advance in the synthesis of BiI3 nanostructures by the hydrothermal method, and is also the first step on seeking the amenable control of morphology and size of such structures using electron beam irradiation. This last process may be particularly appropriate for producing nanostructures for future applications in new devices.

  9. Pressure induced ionic-superionic transition in silver iodide at ambient temperature.

    Science.gov (United States)

    Han, Y H; Wang, H B; Troyan, I A; Gao, C X; Eremets, M I

    2014-01-28

    Silver iodide (AgI-V) is an archetypical ionic compound for studying the formation mechanism of a superionic state. Previous studies have proven that superionic AgI with high ionic conductivity greater than 0.1 Ω(-1)cm(-1) could only be obtained at high temperatures. We show in this paper that high pressure could also induce the superionic state in AgI even at ambient temperature. Using electrochemical impedance spectroscopy, we investigated Ag(+) ions diffusing in rock-salt structured AgI-III and KOH-type AgI-V under high pressures and directly observed the superionic state in AgI-V. The diffusion coefficient of AgI-V is ∼3.4 × 10(-4)-8.6 × 10(-4) cm(2)/s in the investigated pressure range of 12-17 GPa, comparable with those of superionic α-AgI and AgI-III'. By analyzing the half infinite length Warburg diffusion process, two parameters α and β, which closely relate to the disordered state of Ag(+) ions, have been determined and it was suggested that Ag(+) ions in AgI-V become disordered. The ionic conductivity of AgI-V is three orders of magnitude higher than that of AgI-III, and has reached around 0.1 Ω(-1)cm(-1). Evidence for all three, the diffusion coefficient, α and β, and conductivity have proven that AgI-V is a superionic conductor at ambient temperature.

  10. Potassium Iodide Potentiates Broad-Spectrum Antimicrobial Photodynamic Inactivation Using Photofrin.

    Science.gov (United States)

    Huang, Liyi; Szewczyk, Grzegorz; Sarna, Tadeusz; Hamblin, Michael R

    2017-02-23

    It is known that noncationic porphyrins such as Photofrin (PF) are effective in mediating antimicrobial photodynamic inactivation (aPDI) of Gram-positive bacteria or fungi. However, the aPDI activity of PF against Gram-negative bacteria is accepted to be extremely low. Here we report that the nontoxic inorganic salt potassium iodide (KI) at a concentration of 100 mM when added to microbial cells (10(8)/mL) + PF (10 μM hematoporphyrin equivalent) + 415 nm light (10 J/cm(2)) can eradicate (>6 log killing) five different Gram-negative species (Escherichia coli, Pseudomonas aeruginosa, Klebsiella pneumoniae, Proteus mirabilis, and Acinetobacter baumannii), whereas no killing was obtained without KI. The mechanism of action appears to be the generation of microbicidal molecular iodine (I2/I3(-)) as shown by comparable bacterial killing when cells were added to the mixture after completion of illumination and light-dependent generation of iodine as detected by the formation of the starch complex. Gram-positive methicillin-resistant Staphylococcus aureus is much more sensitive to aPDI (200-500 nM PF), and in this case potentiation by KI may be mediated mainly by short-lived iodine reactive species. The fungal yeast Candida albicans displayed intermediate sensitivity to PF-aPDI, and killing was also potentiated by KI. The reaction mechanism occurs via singlet oxygen ((1)O2). KI quenched (1)O2 luminescence (1270 nm) at a rate constant of 9.2 × 10(5) M(-1) s(-1). Oxygen consumption was increased when PF was illuminated in the presence of KI. Hydrogen peroxide but not superoxide was generated from illuminated PF in the presence of KI. Sodium azide completely inhibited the killing of E. coli with PF/blue light + KI.

  11. Investigations regarding the wet decontamination of fluorescent lamp waste using iodine in potassium iodide solutions.

    Science.gov (United States)

    Tunsu, Cristian; Ekberg, Christian; Foreman, Mark; Retegan, Teodora

    2015-02-01

    With the rising popularity of fluorescent lighting, simple and efficient methods for the decontamination of discarded lamps are needed. Due to their mercury content end-of-life fluorescent lamps are classified as hazardous waste, requiring special treatment for disposal. A simple wet-based decontamination process is required, especially for streams where thermal desorption, a commonly used but energy demanding method, cannot be applied. In this study the potential of a wet-based process using iodine in potassium iodide solution was studied for the recovery of mercury from fluorescent lamp waste. The influence of the leaching agent's concentration and solid/liquid ratio on the decontamination efficiency was investigated. The leaching behaviour of mercury was studied over time, as well as its recovery from the obtained leachates by means of anion exchange, reduction, and solvent extraction. Dissolution of more than 90% of the contained mercury was achieved using 0.025/0.05 M I2/KI solution at 21 °C for two hours. The efficiency of the process increased with an increase in leachant concentration. 97.3 ± 0.6% of the mercury contained was dissolved at 21 °C, in two hours, using a 0.25/0.5M I2/KI solution and a solid to liquid ratio of 10% w/v. Iodine and mercury can be efficiently removed from the leachates using Dowex 1X8 anion exchange resin or reducing agents such as sodium hydrosulphite, allowing the disposal of the obtained solution as non-hazardous industrial wastewater. The extractant CyMe4BTBP showed good removal of mercury, with an extraction efficiency of 97.5 ± 0.7% being achieved in a single stage. Better removal of mercury was achieved in a single stage using the extractants Cyanex 302 and Cyanex 923 in kerosene, respectively.

  12. Influence of iodide ingestion on nitrate metabolism and blood pressure following short-term dietary nitrate supplementation in healthy normotensive adults.

    Science.gov (United States)

    Bailey, Stephen J; Blackwell, Jamie R; Wylie, Lee J; Emery, Annabelle; Taylor, Ellie; Winyard, Paul G; Jones, Andrew M

    2017-02-28

    Uptake of inorganic nitrate (NO3(-)) into the salivary circulation is a rate-limiting step for dietary NO3(-) metabolism in mammals. It has been suggested that salivary NO3(-) uptake occurs in competition with inorganic iodide (I(-)). Therefore, this study tested the hypothesis that I(-) supplementation would interfere with NO3(-) metabolism and blunt blood pressure reductions after dietary NO3(-) supplementation. Nine healthy adults (4 male, mean ± SD, age 20 ± 1 yr) reported to the laboratory for initial baseline assessment (control) and following six day supplementation periods with 140 mL·day(-1) NO3(-)-rich beetroot juice (8.4 mmol NO3(-)·day(-1)) and 198 mg potassium gluconate·day(-1) (nitrate), and 140 mL·day(-1) NO3(-)-rich beetroot juice and 450 μg potassium iodide·day(-1) (nitrate + iodide) in a randomized, cross-over experiment. Salivary [I(-)] was higher in the nitrate + iodide compared to the control and NIT trials (P iodide trials compared to the control trial (P iodide trial compared to the nitrate trial (P iodide trials (P > 0.05). Systolic blood pressure was lower than control (112 ± 13 mmHg) in the nitrate (106 ± 13 mmHg) and nitrate + iodide (106 ± 11 mmHg) trials (P iodide trials (P > 0.05). In conclusion, co-ingesting NO3(-) and I(-) perturbed salivary NO3(-) uptake, but the increase in salivary and plasma [NO2(-)] and the lowering of blood pressure were similar compared to NO3(-) ingestion alone. Therefore, increased dietary I(-) intake, which is recommended in several countries worldwide as an initiative to offset hypothyroidism, does not appear to compromise the blood pressure reduction afforded by increased dietary NO3(-) intake.

  13. Potassium iodide (KI) to block the thyroid from exposure to I-131: current questions and answers to be discussed.

    Science.gov (United States)

    Reiners, Christoph; Schneider, Rita

    2013-05-01

    Thyroid cancer in children and adolescents has to be considered as the most severe health consequence of a nuclear reactor emergency with release of radioiodine into the atmosphere. High doses of potassium iodide are effective to block radioiodine thyroid uptake and to prevent development of thyroid cancer years later. However, there are controversies concerning thyroid cancer risk induced by radioiodine exposure in adults. Further, the interaction of nutritional supply of potassium iodide and radioiodine uptake as well as the interaction of radioiodine with certain drugs has not been addressed properly in existing guidelines and recommendations. How to proceed in case of repeated release of radioiodine is an open, very important question which came up again recently during the Fukushima accident. Lastly, the side effects of iodine thyroid blocking and alternatives of this procedure have not been addressed systematically up to now in guidelines and recommendations. These questions can be answered as follows: in adults, the risk to develop thyroid cancer is negligible. In countries, where nutritional iodine deficiency is still an issue, the risk to develop thyroid cancer after a nuclear reactor emergency has to be considered higher because the thyroid takes up more radioiodine as in the replete condition. Similarly, in patients suffering from thyrotoxicosis, hypothyroidism or endemic goitre not being adequately treated radioiodine uptake is higher than in healthy people. In case of repeated or continued radioiodine release, more than one dose of potassium iodide may be necessary and be taken up to 1 week. Repeated iodine thyroid blocking obviously is not harmful. Side effects of iodine thyroid blocking should not be overestimated; there is little evidence for adverse effects in adults. Newborns and babies, however, may be more sensitive to side effects. In the rare case of iodine hypersensitivity, potassium perchlorate may be applied as an alternative to iodine for

  14. The solvent shell structure of aqueous iodide: X-ray absorption spectroscopy and classical, hybrid QM/MM and full quantum molecular dynamics simulations

    Energy Technology Data Exchange (ETDEWEB)

    Pham, V.T. [Ecole Polytechnique Federale de Lausanne, Laboratoire de spectroscopie ultrarapide, ISIC, FSB-BSP, CH-1015 Lausanne (Switzerland); Tavernelli, I. [Ecole Polytechnique Federale de Lausanne, Laboratoire de chimie et biochimie computationnelles, ISIC, FSB-BSP, CH-1015 Lausanne (Switzerland); Milne, C.J.; van der Veen, R.M. [Ecole Polytechnique Federale de Lausanne, Laboratoire de spectroscopie ultrarapide, ISIC, FSB-BSP, CH-1015 Lausanne (Switzerland); D' Angelo, P. [Dipartimento di Chimica, Universita di Roma ' La Sapienza' , Ple A. Moro 5, 00185 Roma (Italy); Bressler, Ch. [Ecole Polytechnique Federale de Lausanne, Laboratoire de spectroscopie ultrarapide, ISIC, FSB-BSP, CH-1015 Lausanne (Switzerland); Chergui, M., E-mail: Majed.Chergui@epfl.ch [Ecole Polytechnique Federale de Lausanne, Laboratoire de spectroscopie ultrarapide, ISIC, FSB-BSP, CH-1015 Lausanne (Switzerland)

    2010-05-25

    Graphical abstract: The L{sub 3}-edge EXAFS spectra of aqueous iodide are compared to classical, QM/MM and DFT-based molecular dynamics simulations. The QM/MM simulations reproduce best the experimental data. An anisotropy of the solvation shell is also identified. - Abstract: The L{sub 3} X-ray absorption spectrum of aqueous iodide is reported, and its EXAFS is compared to theoretical spectra reconstructed from the radial distribution function of the iodide hydration obtained from classical, hybrid Quantum Mechanics Molecular Mechanics, (QM/MM) and full quantum (density functional theory, DFT) molecular dynamics simulations. Since EXAFS is mainly sensitive to short distances around the iodide ion, it is a direct probe of the local solvation structure. The comparison shows that QM/MM simulations deliver a satisfactory description of the EXAFS signal, while nonpolarizable classical simulations are somewhat less satisfactory and DFT-based simulations perform poorly. We also identify a weak anisotropy of the water solvation shell around iodide, which may be of importance in electron photoejection experiments.

  15. A colorimetric method for highly sensitive and accurate detection of iodide by finding the critical color in a color change process using silver triangular nanoplates.

    Science.gov (United States)

    Yang, Xiu-Hua; Ling, Jian; Peng, Jun; Cao, Qiu-E; Ding, Zhong-Tao; Bian, Long-Chun

    2013-10-10

    In this contribution, we demonstrated a novel colorimetric method for highly sensitive and accurate detection of iodide using citrate-stabilized silver triangular nanoplates (silver TNPs). Very lower concentration of iodide can induce an appreciable color change of silver TNPs solution from blue to yellow by fusing of silver TNPs to nanoparticles, as confirmed by UV-vis absorption spectroscopy and transmission electron microscopy (TEM). The principle of this colorimetric assay is not an ordinary colorimetry, but a new colorimetric strategy by finding the critical color in a color change process. With this strategy, 0.1 μM of iodide can be recognized within 30 min by naked-eyes observation, and lower concentration of iodide down to 8.8 nM can be detected using a spectrophotometer. Furthermore, this high sensitive colorimetric assay has good accuracy, stability and reproducibility comparing with other ordinary colorimetry. We believe this new colorimetric method will open up a fresh insight of simple, rapid and reliable detection of iodide and can find its future application in the biochemical analysis or clinical diagnosis.

  16. Simultaneous determination of iodide and iodate in povidone iodine solution by ion chromatography with homemade and exchange capacity controllable columns and column-switching technique.

    Science.gov (United States)

    Huang, Zhongping; Zhu, Zuoyi; Subhani, Qamar; Yan, Wenwu; Guo, Weiqiang; Zhu, Yan

    2012-08-17

    A simple ion chromatographic method for simultaneous detection of iodide and iodate in a single running was proposed, with columns packed with homemade functionalized polystyrene-divinylbenzene (PS-DVB) resins and column-switching technique. Homemade resins were functionalized with controllable amounts of quaternary ammonium groups. The low-capacity anion-exchange column and high-capacity anion-exchange column were prepared, due to the resins having different exchange capacities. With this method, iodide and iodate in povidone iodine solution were detected simultaneously in a short time with iodide being eluted off first. A series of standard solutions consisting of target anions of various concentrations from 0.01 mg/L to 100 mg/L were analyzed. Each anion exhibited satisfactory linearity, with correlation coefficient r ≥ 0.9990. The detection limits (LODs) for iodide and iodate obtained by injecting 100 μL of sample were 5.66 and 14.83 μg/L (S/N=3), respectively. A spiking study was performed with satisfactory recoveries between 101.2% and 100.6% for iodide and iodate.

  17. Antineoplastic effect of iodine and iodide in dimethylbenz[a]anthracene-induced mammary tumors: association between lactoperoxidase and estrogen-adduct production.

    Science.gov (United States)

    Soriano, Ofelia; Delgado, Guadalupe; Anguiano, Brenda; Petrosyan, Pavel; Molina-Servín, Edith D; Gonsebatt, Maria E; Aceves, Carmen

    2011-08-01

    Several groups, including ours, have reported that iodine exhibited antiproliferative and apoptotic effects in various cancer cells only if this element is supplemented as molecular iodine, or as iodide, to cells that are able to oxidize it with the enzyme thyroperoxidase. In this study, we analyzed the effect of various concentrations of iodine and/or iodide in the dimethylbenz[a]anthracene (DMBA) mammary cancer model in rats. The results show that 0.1% iodine or iodide increases the expression of peroxisome proliferator-activated receptor type γ (PPARγ), triggering caspase-mediated apoptosis pathways in damaged mammary tissue (DMBA-treated mammary gland) as well as in frank mammary tumors, but not in normal mammary gland. DMBA treatment induces the expression of lactoperoxidase, which participates in the antineoplastic effect of iodide and could be involved in the pro-neoplastic effect of estrogens, increasing the formation of DNA adducts. In conclusion, our results show that a supplement of 0.1% molecular iodine/potassium iodide (0.05/0.05%) exert antineoplastic effects, preventing estrogen-induced DNA adducts and inducing apoptosis through PPARγ/caspases in pre-cancer and cancerous cells. Since this iodine concentration does not modify the cytology (histology, apoptosis rate) or physiology (triiodothyronine and thyrotropin) of the thyroid gland, we propose that it be considered as an adjuvant treatment for premenopausal mammary cancer.

  18. Synthesis, Characterization, Crystal Structure and Quantum Chemical Calculation of Novel Compound 1,3-Dimethyl-2-ferrocenylmethylbenzimidazolium Iodide

    Institute of Scientific and Technical Information of China (English)

    ZHANG Jing; YANG Bing-Qin; ZHU Hai-Yan; LI Tao; WEN Zhen-Yi

    2006-01-01

    A novel benzimidazole derivative, 1,3-dimethyl-2-ferrocenylmethylbenzimidazolium iodide (1) was synthesized and characterized by elemental analysis, MS, 1H NMR and IR spectra. Its crystal structure was determined by X-ray single crystal diffraction, and the title compound belongs to monoclinic system with space group P2(1)/c.According to the crystal structure, the quantum chemistry calculation was performed by Gaussian 03 program, and full geometry optimizations of the title compound were carried out with DFT method at B3LYP/6-31G level. Its structure, stability, frontier molecular orbital components and net charge distribution were discussed.

  19. Infrared Spectra and Structure of Poly(Vinylalcohol) Films Obtained From Aqueous Solutions with Potassium Iodide Additive

    Science.gov (United States)

    Sushko, N. I.; Zagorskaya, S. A.; Tretinnikov, O. N.

    2013-11-01

    The crystallinity and H-bonds in poly(vinylalcohol) films obtained from aqueous solutions with potassium iodide additive were investigated by IR spectroscopy. It was established that addition of KI caused the degree of polymer crystallinity to increase. The band of hydroxyl stretching vibrations (νOH) shifted toward higher frequency in spectra of films with KI additive. This indicated a change in the system of H-bonds in the polymer. The dependences of both the degree of crystallinity and the shift of the νOH band on the salt concentration were qualitatively different in shape.

  20. Potassium Iodide and Acrylamide Fluorescence Quenching Studies on Gamma-Crystallins of Human Lenses in Development and Aging

    Institute of Scientific and Technical Information of China (English)

    1992-01-01

    γ_1-γ_2-and γ_3-crystallin(corresponding to γs-,γC-and γD- crys-tallin respectively)of human fetal,2 year and 20~+ year old lenses areseparated by Sephadex gel chromatography.lodide and acrylamide are usedto quench the tryptophane fluorescence of sub-γ-crystalline fractions and Ksvand fa values are calculated.The results show that iodide has no clear quench-ing effects on all γ-crystallins,the quenching effects of acrylamide on the tryp-tophan fluorescences of γ1-γ2-and γ3-crystallin from lenses of the ...

  1. Hole-conductor-free perovskite organic lead iodide heterojunction thin-film solar cells: High efficiency and junction property

    Science.gov (United States)

    Shi, Jiangjian; Dong, Juan; Lv, Songtao; Xu, Yuzhuan; Zhu, Lifeng; Xiao, Junyan; Xu, Xin; Wu, Huijue; Li, Dongmei; Luo, Yanhong; Meng, Qingbo

    2014-02-01

    Efficient hole-conductor-free organic lead iodide thin film solar cells have been fabricated with a sequential deposition method, and a highest efficiency of 10.49% has been achieved. Meanwhile, the ideal current-voltage model for a single heterojunction solar cell is applied to clarify the junction property of the cell. The model confirms that the TiO2/CH3NH3PbI3/Au cell is a typical heterojunction cell and the intrinsic parameters of the cell are comparable to that of the high-efficiency thin-film solar cells.

  2. Copper/N,N-Dimethylglycine Catalyzed Goldberg Reactions Between Aryl Bromides and Amides, Aryl Iodides and Secondary Acyclic Amides

    Directory of Open Access Journals (Sweden)

    Liqin Jiang

    2014-08-01

    Full Text Available An efficient and general copper-catalyzed Goldberg reaction at 90–110 °C between aryl bromides and amides providing the desired products in good to excellent yields has been developed using N,N-dimethylglycine as the ligand. The reaction is tolerant toward a wide range of amides and a variety of functional group substituted aryl bromides. In addition, hindered, unreactive aromatic and aliphatic secondary acyclic amides, known to be poor nucleophiles, are efficiently coupled with aryl iodides through this simple and cheap copper/N,N-dimethylglycine catalytic system.

  3. Hail prevention by ground-based silver iodide generators: Results of historical and modern field projects

    Science.gov (United States)

    Dessens, J.; Sánchez, J. L.; Berthet, C.; Hermida, L.; Merino, A.

    2016-03-01

    The science of hail suppression by silver iodide (AgI) cloud seeding was developed during the second half of the 20th century in laboratory and tested in several research or operational projects using three delivery methods for the ice forming particles: ground generators, aircraft, and rockets. The randomization process for the seeding was often considered as the imperative method for a better evaluation but failed to give firm results, mostly because the projects did not last long enough considering the hazardous occurrence of severe hailfalls, and also probably due to the use of improper hail parameters. At the same time and until now, a continuous long-term research and operational field project (1952-2015) using ground generator networks has been conducted in France under the leadership of the Association Nationale d'Etude et de Lutte contre les Fléaux Atmosphériques (ANELFA), with a control initially based on annual insurance loss-to-risk ratios, then on hailpad data. More recently (2000-2009), a companion ground seeding project was developed in the north of Spain, with control mostly based on microphysical and hailpad data. The present paper, which focuses on hail suppression by ground seeding, reviews the production of the AgI nuclei, their dispersion and measurement in the atmosphere, as well as their observed or simulated effects in clouds. The paper summarizes the results of the main historical projects in Switzerland, Argentina, and North America, and finally concentrates on the current French and Spanish projects, with a review of already published results, complemented by new ones recently collected in Spain. The conclusion, at least for France and Spain, is that if ground seeding is performed starting 3 hours before the hail falls at the ground with a 10-km mesh AgI generator network located in the developing hailstorm areas, each generator burning about 9 g of AgI per hour, the hailfall energy of the most severe hail days is decreased by about 50%.

  4. Potassium iodide for thyroid blockade in a reactor accident: administrative policies that govern its use.

    Science.gov (United States)

    Becker, D V; Zanzonico, P

    1997-04-01

    A marked increase in thyroid cancer among young children who were in the vicinity of the Chernobyl nuclear power plant at the time of the 1986 accident strongly suggests a possible causal relationship to the large amounts of radioactive iodine isotopes in the resulting fallout. Although remaining indoors, restricting consumption of locally produced milk and foodstuffs, and evacuation are important strategies in a major breach-of-containment accident, stable potassium iodide (KI) prophylaxis given shortly before or immediately after exposure can reduce greatly the thyroidal accumulation of radioiodines and the resulting radiation dose. Concerns about possible side effects of large-scale, medically unsupervised KI consumption largely have been allayed in light of the favorable experience in Poland following the Chernobyl accident; 16 million persons received single administrations of KI with only rare occurrence of side effects and with a probable 40% reduction in projected thyroid radiation dose. Despite the universal acceptance of KI as an effective thyroid protective agent, supplies of KI in the US are not available for public distribution in the event of a reactor accident largely because government agencies have argued that stockpiling and distribution of KI to other than emergency workers cannot be recommended in light of difficult distribution logistics, problematic administrative issue, and a calculated low cost-effectiveness. However, KI in tablet form is expensive and has a long shelf life, and many countries have largely stockpiles and distribution programs. The World Health Organization recognizes the benefits of stable KI and urges its general availability. At present there are 110 operating nuclear power plants in the US and more than 300 in the rest of the world. These reactors product 17% of the world's electricity and in some countries up to 60-70% of the total electrical energy. Almost all US nuclear power plants have multistage containment

  5. Study on the Effect of Synthesis Temperature on the Structural, Surface Morphological and Optical Properties of Methyl Ammonium Lead Iodide Nanoparticles by Sol-Gel Method

    Science.gov (United States)

    Benazeera Beegum, K. A.; Paulose, Maria; Peter, V. J.; Raphael, Rakhy; Sreeja, V. G.; Anila, E. I.

    2016-09-01

    Lead halide perovskite solar cells have recently attracted tremendous attention because of their excellent photovoltaic efficiency. The quality and stability of perovskite films are critical for solar cells. We report the synthesis of methyl ammonium lead iodide (MAPbKI3) nanoparticles from methyl amine, hydroiodic acid and lead iodide by sol-gel method. Three powder samples of Methyl ammonium Lead Iodide were prepared at 50 °C, 90 °C, and 100 °C. The powder samples were characterised by X-ray diffraction (XRD), Diffuse reflectance spectroscopy (DRS), Scanning Electron Microscopy (SEM), Energy Dispersive Analysis of X- rays (EDAX) and Photoluminescence (PL). The presence of carbon, hydrogen and nitrogen were examined through CHN studies. The surface morphology, band gap, and elemental contents changes with temperature. The XRD pattern exhibited major reflections from (110), (220), (310), (224) and (314) planes in agreement with JCPDS file No: 00-021-1276, revealing tetragonal structure.

  6. Propylthiouracil, Perchlorate, and Thyroid-Stimulating Hormone Modulate High Concentrations of Iodide Instigated Mitochondrial Superoxide Production in the Thyroids of Metallothionein I/II Knockout Mice

    Directory of Open Access Journals (Sweden)

    Qi Duan

    2016-03-01

    Full Text Available BackgroundIncreased oxidative stress has been suggested as one of the underlying mechanisms in iodide excess-induced thyroid disease. Metallothioneins (MTs are regarded as scavengers of reactive oxygen species (ROS in oxidative stress. Our aim is to investigate the effects of propylthiouracil (PTU, a thyroid peroxidase inhibitor, perchlorate (KClO4, a competitive inhibitor of iodide transport, and thyroid stimulating hormone (TSH on mitochondrial superoxide production instigated by high concentrations of iodide in the thyroids of MT-I/II knockout (MT-I/II KO mice.MethodsEight-week-old 129S7/SvEvBrd-Mt1tm1Bri Mt2tm1Bri/J (MT-I/II KO mice and background-matched wild type (WT mice were used.ResultsBy using a mitochondrial superoxide indicator (MitoSOX Red, lactate dehydrogenase (LDH release, and methyl thiazolyl tetrazolium (MTT assay, we demonstrated that the decreased relative viability and increased LDH release and mitochondrial superoxide production induced by potassium iodide (100 µM can be relieved by 300 µM PTU, 30 µM KClO4, or 10 U/L TSH in the thyroid cell suspensions of both MT-I/II KO and WT mice (P<0.05. Compared to the WT mice, a significant decrease in the relative viability along with a significant increase in LDH release and mitochondrial superoxide production were detected in MT-I/II KO mice(P<0.05.ConclusionWe concluded that PTU, KClO4, or TSH relieved the mitochondrial oxidative stress induced by high concentrations of iodide in the thyroids of both MT-I/II KO and WT mice. MT-I/II showed antioxidant effects against high concentrations of iodide-induced mitochondrial superoxide production in the thyroid.

  7. 二甲基碘化金的合成与结构表征%Synthesis and Characterization of Dimethylgold(III) Iodide

    Institute of Scientific and Technical Information of China (English)

    雷婧; 晏彩先; 常桥稳; 毛丽秋; 刘伟平

    2015-01-01

    Dimethylgold iodide, a key intermediates for organometallic compounds of gold, was prepared via the reaction of methyl-magnesium iodide and potassium tetrachloroaurate(III) in a mixture of ether and hexane. Its chemical structure was characterized by using elemental analysis, MS, IR, 1H-NMR along with single X-ray diffraction. The results reveal that dimethylgold iodide is a iodide-bridged dimeric compound in which each gold atom is coordinated by two methyl groups and two iodide ions, forming a planner complex unit. Two complex units are bridged together by two iodides and share the same plane.%以甲基碘化镁和氯金酸钾为原料,在乙醚和正己烷混合溶液中合成一种制备有机金化合物的关键中间体—二甲基碘化金([(CH3)2AuI]2)。通过元素分析、质谱、红外光谱、核磁共振氢谱和单晶X射线衍射测定和表征了其化学结构。二甲基碘化金为碘桥双核配合物,每个金原子与2个甲基和2个碘离子配位,形成四配位的平面正方形,2个配位单元通过碘离子桥联,处于同一平面。

  8. Synthesis and evaluation of antibacterial polyurethane coatings made from soybean oil functionalized with dimethylphenylammonium iodide and hydroxyl groups.

    Science.gov (United States)

    Bakhshi, Hadi; Yeganeh, Hamid; Mehdipour-Ataei, Shahram

    2013-06-01

    Preparation of antibacterial polyurethane coatings from novel functional soybean oil was considered in this work. First, epoxidized soybean oil (ESBO) as a low price and widely available renewable resource raw material was subjected to the reaction with aniline using an ionic liquid as a green catalyst. The intermediate phenylamine containing polyol (SAP) was then methylated by reaction with methyl iodide to produce a polyol (QAP) with pendant dimethylphenylammonium iodide groups. To regulate the physical and mechanical properties as well as biological characteristics of final coatings, QAP was mixed with different portions of a similar soybean oil-based polyol (MSP) without quaternary ammonium groups. The mixtures were reacted with isophorone diisocyanate to produce crosslinked polyurethane coatings. Evaluation of viscoelastic properties by DMA method revealed single phase structure with Tg in the range of 50-82°C. Stress-strain analysis of the prepared polyurethanes showed initial modulus, tensile strength, and elongation at break in the ranges of 13-299 MPa, 4.5-13.8 MPa, and 16-109%, respectively. Additionally, the coatings showed good adherence to aluminum and PVC substrates. The solvent extracted samples showed excellent biocompatibility as determined by monitoring L929 fibroblast cells morphology and MTT assay. Meanwhile, very promising antibacterial properties against both Gram-positive (S. aureus) and Gram-negative (E. coli) bacteria with bacterial reduction in the range of 83-100% was observed.

  9. K-edge XANES investigation of octakis(DMSO)lanthanoid(III) complexes in DMSO solution and solid iodides.

    Science.gov (United States)

    D'Angelo, Paola; Migliorati, Valentina; Spezia, Riccardo; De Panfilis, Simone; Persson, Ingmar; Zitolo, Andrea

    2013-06-14

    The potential of high energy XANES (X-ray absorption near edge structure) as a tool for the structural analysis of lanthanoid-containing systems has been explored. The K-edge XANES spectra of La(3+), Gd(3+), and Lu(3+) ions both in DMSO solution and solid octakis(DMSO)lanthanoid(III) iodides have been analysed. Although the K-edges of lanthanoids cover the energy range of 38 (La) to 65 (Lu) keV, the large widths of the core hole states do not appreciably reduce the potential structural information of the XANES data. We show that, for lanthanoid compounds, accurate structural parameters are obtained from the analysis of K-edge XANES signals if a deconvolution procedure is carried out. We found that in solid octakis(DMSO)lanthanoid(III) iodides the Ln(3+) ions are coordinated by eight DMSO ligands arranged in a quite symmetric fashion. In DMSO solution the Ln(3+) ions retain a regular eight-coordination structure and the coordination number does not change along the series. In contrast to when in water the second coordination shell has been found to provide a negligible contribution to the XANES spectra of Ln(3+) ions in DMSO solution.

  10. An inorganic hole conductor for organo-lead halide perovskite solar cells. Improved hole conductivity with copper iodide.

    Science.gov (United States)

    Christians, Jeffrey A; Fung, Raymond C M; Kamat, Prashant V

    2014-01-15

    Organo-lead halide perovskite solar cells have emerged as one of the most promising candidates for the next generation of solar cells. To date, these perovskite thin film solar cells have exclusively employed organic hole conducting polymers which are often expensive and have low hole mobility. In a quest to explore new inorganic hole conducting materials for these perovskite-based thin film photovoltaics, we have identified copper iodide as a possible alternative. Using copper iodide, we have succeeded in achieving a promising power conversion efficiency of 6.0% with excellent photocurrent stability. The open-circuit voltage, compared to the best spiro-OMeTAD devices, remains low and is attributed to higher recombination in CuI devices as determined by impedance spectroscopy. However, impedance spectroscopy revealed that CuI exhibits 2 orders of magnitude higher electrical conductivity than spiro-OMeTAD which allows for significantly higher fill factors. Reducing the recombination in these devices could render CuI as a cost-effective competitor to spiro-OMeTAD in perovskite solar cells.

  11. Parameters influencing the deposition of methylammonium lead halide iodide in hole conductor free perovskite-based solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, Bat-El; Gamliel, Shany; Etgar, Lioz, E-mail: lioz.etgar@mail.huji.ac.il [Institute of Chemistry, Casali Center for Applied Chemistry, The Hebrew University of Jerusalem, Jerusalem 90400 (Israel)

    2014-08-01

    Perovskite is a promising light harvester for use in photovoltaic solar cells. In recent years, the power conversion efficiency of perovskite solar cells has been dramatically increased, making them a competitive source of renewable energy. An important parameter when designing high efficiency perovskite-based solar cells is the perovskite deposition, which must be performed to create complete coverage and optimal film thickness. This paper describes an in-depth study on two-step deposition, separating the perovskite deposition into two precursors. The effects of spin velocity, annealing temperature, dipping time, and methylammonium iodide concentration on the photovoltaic performance are studied. Observations include that current density is affected by changing the spin velocity, while the fill factor changes mainly due to the dipping time and methylammonium iodide concentration. Interestingly, the open circuit voltage is almost unaffected by these parameters. Hole conductor free perovskite solar cells are used in this work, in order to minimize other possible effects. This study provides better understanding and control over the perovskite deposition through highly efficient, low-cost perovskite-based solar cells.

  12. Pd-mediated rapid cross-couplings using [(11) C]methyl iodide: groundbreaking labeling methods in (11) C radiochemistry.

    Science.gov (United States)

    Doi, Hisashi

    2015-03-01

    Prof. Bengt Långström is a pioneer in the field of chemistry-driven positron emission tomography (PET) imaging. He has developed a variety of excellent radiolabeling methodologies using the methods of organic chemistry, with the aim of widening the potential of PET in the study of life. Among his groundbreaking achievements in (11) C radiochemistry, there is the discovery of the Pd-mediated rapid cross-coupling reaction using [(11) C]methyl iodide. It was first reported by his Uppsala group in 1994-1995 and was further investigated by his and other groups with a view of enhancing its generality and practicability. This reaction is currently considered one of the basic methods for (11) C-labeling of low-weight organic compounds. This paper presents a short summary of the background and the development of Pd-mediated rapid cross-couplings of [(11) C]methyl iodide, with a focus not only on organostannanes, but also on organoboranes, organozincs, and terminal acetylene compounds. All these reactions have proven to be dependable (11) C-labeling methodologies that use chemically reliable carbon-carbon bond formation reactions.

  13. Chlorine Dioxide-Iodide-Methyl Acetoacetate Oscillation Reaction Investigated by UV-Vis and Online FTIR Spectrophotometric Method

    Science.gov (United States)

    Shi, Laishun; Wang, Xiaomei; Li, Na; Liu, Jie; Yan, Chunying

    2012-01-01

    In order to study the chemical oscillatory behavior and mechanism of a new chlorine dioxide-iodide ion-methyl acetoacetate reaction system, a series of experiments were done by using UV-Vis and online FTIR spectrophotometric method. The initial concentrations of methyl acetoacetate, chlorine dioxide, potassium iodide, and sulfuric acid and the pH value have great influence on the oscillation observed at wavelength of 289 nm. There is a preoscillatory or induction period, and the amplitude and the number of oscillations are associated with the initial concentration of reactants. The equations for the triiodide ion reaction rate changing with reaction time and the initial concentrations in the oscillation stage were obtained. Oscillation reaction can be accelerated by increasing temperature. The apparent activation energies in terms of the induction period and the oscillation period were 26.02 KJ/mol and 17.65 KJ/mol, respectively. The intermediates were detected by the online FTIR analysis. Based upon the experimental data in this work and in the literature, a plausible reaction mechanism was proposed for the oscillation reaction. PMID:22454614

  14. Lead iodide perovskite sensitized all-solid-state submicron thin film mesoscopic solar cell with efficiency exceeding 9%.

    KAUST Repository

    Kim, Hui-Seon

    2012-08-21

    We report on solid-state mesoscopic heterojunction solar cells employing nanoparticles (NPs) of methyl ammonium lead iodide (CH(3)NH(3))PbI(3) as light harvesters. The perovskite NPs were produced by reaction of methylammonium iodide with PbI(2) and deposited onto a submicron-thick mesoscopic TiO(2) film, whose pores were infiltrated with the hole-conductor spiro-MeOTAD. Illumination with standard AM-1.5 sunlight generated large photocurrents (J(SC)) exceeding 17 mA/cm(2), an open circuit photovoltage (V(OC)) of 0.888 V and a fill factor (FF) of 0.62 yielding a power conversion efficiency (PCE) of 9.7%, the highest reported to date for such cells. Femto second laser studies combined with photo-induced absorption measurements showed charge separation to proceed via hole injection from the excited (CH(3)NH(3))PbI(3) NPs into the spiro-MeOTAD followed by electron transfer to the mesoscopic TiO(2) film. The use of a solid hole conductor dramatically improved the device stability compared to (CH(3)NH(3))PbI(3) -sensitized liquid junction cells.

  15. Synthesis aspects, structural, spectroscopic, antimicrobial and room temperature ferromagnetism of zinc iodide complex with Schiff based ligand

    Science.gov (United States)

    Shakila, K.; Kalainathan, S.

    2015-01-01

    In this paper, we report the successful growth of complex compound of zinc iodide with thiocarbamide by slow evaporation method. The single crystal XRD study reveals that the crystal belongs to monoclinic system with centrosymmetric space group and powder XRD analysis shows that the perfect crystalline nature of the crystal. The presence of functional group and element were confirmed from FT-IR and EDAX analysis. Optical absorbance of the grown crystal was studied by UV-Vis spectrophotometer. The optical constants were calculated from the optical absorbance data such as refractive index (n), extinction coefficient (K) and reflectance (R). The optical band gap (Eg) of thiocarbamide zinc iodide crystal is 4.22 eV. The magnetic properties of grown crystal have been determined by Vibrating Sample Magnetometry (VSM). Room temperature magnetization revealed a ferromagnetic behaviour for the grown crystal. The antibacterial and antifungal activities of the title compound were performed by well diffusion method and MIC method against the standard bacteria like Staphylococcus aureus, Escherichia coli, Klebsiella pneumonia and against fungus like Aspergillus niger, Rhizopus sps and Penicillium sps. Thermal behaviour of the crystal has been investigated using thermogravimetric analysis (TGA) and differential thermal analysis (DTA).

  16. UV-assisted photocatalytic synthesis of highly dispersed Ag nanoparticles supported on DNA decorated graphene for quantitative iodide analysis.

    Science.gov (United States)

    Kong, Fen-Ying; Li, Wei-Wei; Wang, Jing-Yi; Wang, Wei

    2015-07-15

    Herein, we report, for the first time, the synthesis of reduced graphene oxide-DNA-Ag (RGO-DNA-Ag) nanohybrids by ultraviolet (UV) irradiation of aqueous solutions of GO and Ag ions in the presence of DNA. The morphology and microstructure characterizations of the resultant nanohybrids reveal that the proposed method leads to the simultaneous reduction of GO and Ag ions together with efficient dispersion of Ag nanoparticles on the surface of RGO sheets. This simple and fast synthesis route is carried out at ambient conditions without using any additional chemical reducing agents, which has the potential to provide new avenues for the green fabrication of various RGO-based nanomaterials. Additionally, the RGO-DNA-Ag nanohybrids can be utilized as a novel sensing interfacial for direct determination of iodide by simple differential pulse voltammetry (DPV), without requiring any preceding preconcentration of the analyte. Based on the RGO-DNA-Ag nanohybrids modified electrode, a wide linear range of 1μM-1mM and a low detection limit of 0.2μM were obtained. This sensitive and direct method of analysis can be applied successfully to the determination of iodide in real samples.

  17. P(MMA-EMA Random Copolymer Electrolytes Incorporating Sodium Iodide for Potential Application in a Dye-Sensitized Solar Cell

    Directory of Open Access Journals (Sweden)

    Nurul Akmaliah Dzulkurnain

    2015-02-01

    Full Text Available Polymer electrolytes based on 90 wt% of methyl methacrylate and 10 wt% of ethyl methacrylate (90MMA-co-10EMA incorporating different weight ratios of sodium iodide were prepared using the solution casting method. The complexation between salt and copolymer host has been investigated using Fourier transform infrared spectroscopy. The ionic conductivity and thermal stability of the electrolytes were measured using impedance spectroscopy and differential scanning calorimetry, respectively. Scanning electron microscopy was used to study the morphology of the polymer electrolytes. The ionic conductivity and glass transition temperature increased up to 20 wt% of sodium iodide (5.19 × 10−6 S·cm−1 and decreased with the further addition of salt concentration, because of the crosslinked effect. The morphology behavior of the highest conducting sample also showed smaller pores compared to the other concentration. The total ionic transference number proved that this system was mainly due to ions, and the electrochemical stability window was up to 2.5 V, which is suitable for a dye-sensitized solar cell application. This sample was then tested in a dye-sensitized solar cell and exhibited an efficiency of 0.62%.

  18. Cutaneous sporotrichosis treatment with potassium iodide: a 24 year experience in São Paulo state, Brazil

    Directory of Open Access Journals (Sweden)

    Karin Yamada

    2011-04-01

    Full Text Available BACKGROUND: Sporotrichosis is a subacute or chronic disease caused by a dimorphic fungus, Sporothrix schenckii. The first and most traditional treatment is potassium iodide in satured solution (SSKI used by DE BEURMANN in 1907. For its effectiveness, it is still used for cutaneous sporotrichosis. OBJECTIVE: To evaluate the treatment of cutaneous sporotrichosis with SSKI in relation to clinical cure, side effects, length of treatment and reactivation. METHODS: We conducted a retrospective analysis of medical records over a 24-year period (1981-2005. Patients of all ages who were treated in the hospital´s division of dermatology were included in the study providing that they had a positive culture of S. schenckii. Satured solution of potassium iodide (3 to 6g per day was the treatment prescribed. For children, half of the dose was prescribed. RESULTS: The lymphocutaneous disease was prevalent, the cure rate was 94.7%, side effects were described in 5.5% of the cases, mean length of treatment was 3.5 months and possible reactivation was observed in 11.1%. CONCLUSION: SSKI is an effective drug, with many side effects, but with low frequency. Resolution was for maximum six months of treatment. SSKI has been found to be a very effective drug in this retrospective study of culture-proven cases of cutaneous and lymphocutaneous sporotrichosis. It should be used as first drug of choice especially in resource-limited settings.

  19. Chlorine Dioxide-Iodide-Methyl Acetoacetate Oscillation Reaction Investigated by UV-Vis and Online FTIR Spectrophotometric Method

    Directory of Open Access Journals (Sweden)

    Laishun Shi

    2012-01-01

    Full Text Available In order to study the chemical oscillatory behavior and mechanism of a new chlorine dioxide-iodide ion-methyl acetoacetate reaction system, a series of experiments were done by using UV-Vis and online FTIR spectrophotometric method. The initial concentrations of methyl acetoacetate, chlorine dioxide, potassium iodide, and sulfuric acid and the pH value have great influence on the oscillation observed at wavelength of 289 nm. There is a preoscillatory or induction period, and the amplitude and the number of oscillations are associated with the initial concentration of reactants. The equations for the triiodide ion reaction rate changing with reaction time and the initial concentrations in the oscillation stage were obtained. Oscillation reaction can be accelerated by increasing temperature. The apparent activation energies in terms of the induction period and the oscillation period were 26.02 KJ/mol and 17.65 KJ/mol, respectively. The intermediates were detected by the online FTIR analysis. Based upon the experimental data in this work and in the literature, a plausible reaction mechanism was proposed for the oscillation reaction.

  20. Ion-pair formation of Bi(III)-iodide with some nitrogenous drugs and its application to pharmaceutical preparations.

    Science.gov (United States)

    Abdel-Gawad, F M

    1998-01-01

    A systematic spectrophotometric study on the ion-pair formation of Bi(III)-iodide with amineptine hydrochloride, piribedil and trimebutine maleate is carried out. The optimal experimental conditions pH, concentration of Bi(III) nitrate, potassium iodide; and the nature and amount of organic solvent have been studied. The ion pairs are soluble in 1,2-dichloroethane and the optimum pH range is 2.0-2.8. By application of the methods of Sommer and Job involving non-equimolar solutions, the conditional stability constant (log K') of the Bi(III) piridedil ion pair (1:1) at the optimum pH of 2.4 and an ionic strength (mu) 0.1 M, was found to be 5.436. The validity of Beer's law has been tested in the concentration range 5-50 microg ml(-1) in the organic layer, the relative standard deviation is less than 1%. The method is applied to the determination of these drugs in tablets without interference.

  1. Effect of ionic interaction of chlorode-borate and iodide-borate on their absorption by Lemna minor L

    Energy Technology Data Exchange (ETDEWEB)

    Thellier, M.; Ayadi, A.; Tromeur, C.

    1967-11-27

    The effect of borate ions on the absorption of chloride and iodide ions by Lemna minor was studied by using the radioactive tracers Cl-36 at 23/sup 0/C with an illumination of 8000 Lux and I-131 at 25.5 C with 600 Lux. The absorbed quantities of the tracer elements were measured with a Geiger counter. The concentrations of sodium chloride solutions tested ranged from 0.055 to 1 mM, those of potassium iodide from 0.04 to 4 mM. While the presence of borate ions in the test solutions of NaCl inhibited the absorption of Cl ions by Lemna minor, only a mild inhibition or none at all was noted in the case of the absorption of I ions. Because of the difference of the cations (sodium in the case of Cl, potassium in the case of I) no direct comparison can be drawn between the absorption of the two halogens. The absorption of I by the plant is thought to proceed by a much simpler mechanism than that of Cl.

  2. Lead Iodide Perovskite Sensitized All-Solid-State Submicron Thin Film Mesoscopic Solar Cell with Efficiency Exceeding 9%

    Science.gov (United States)

    Kim, Hui-Seon; Lee, Chang-Ryul; Im, Jeong-Hyeok; Lee, Ki-Beom; Moehl, Thomas; Marchioro, Arianna; Moon, Soo-Jin; Humphry-Baker, Robin; Yum, Jun-Ho; Moser, Jacques E.; Grätzel, Michael; Park, Nam-Gyu

    2012-01-01

    We report on solid-state mesoscopic heterojunction solar cells employing nanoparticles (NPs) of methyl ammonium lead iodide (CH3NH3)PbI3 as light harvesters. The perovskite NPs were produced by reaction of methylammonium iodide with PbI2 and deposited onto a submicron-thick mesoscopic TiO2 film, whose pores were infiltrated with the hole-conductor spiro-MeOTAD. Illumination with standard AM-1.5 sunlight generated large photocurrents (JSC) exceeding 17 mA/cm2, an open circuit photovoltage (VOC) of 0.888 V and a fill factor (FF) of 0.62 yielding a power conversion efficiency (PCE) of 9.7%, the highest reported to date for such cells. Femto second laser studies combined with photo-induced absorption measurements showed charge separation to proceed via hole injection from the excited (CH3NH3)PbI3 NPs into the spiro-MeOTAD followed by electron transfer to the mesoscopic TiO2 film. The use of a solid hole conductor dramatically improved the device stability compared to (CH3NH3)PbI3 -sensitized liquid junction cells. PMID:22912919

  3. Synthesis, structure, photophysical and catalytic properties of CuI-Iodide complexes of di-imine ligands

    Science.gov (United States)

    Mondal, Jahangir; Ghorai, Anupam; Singh, Sunil K.; Saha, Rajat; Patra, Goutam K.

    2016-03-01

    Two new multifunctional CuII based complexes [CuI(L1)] (1) and [Cu2(μ-I)2(L2)] (2) with bidentate N-N donor ligands L1 and imino-pyridyl ligand L2 have been synthesized and characterized by elemental analysis, IR, UV-Vis, NMR and single crystal X-ray crystallography. The bidentate di-imine ligand (L1) forms monomeric CuI complex (1) whereas the bis-bidentate di-imine ligand (L2) favours the formation of dimeric CuI complex (2) in association with two bridging iodides. Structural analysis reveals that in complex 1 each monomeric units are connected by π⋯π and C-H⋯π interactions to form 3D supramolecular structure whereas in complex 2 each molecules are connected by only π⋯π interactions to form 3D supramolecular structure. The photoluminescence properties of the complexes have been studied at room temperature. Theoretical analysis shows that HOMO is focused on the Cu and iodides while LUMO is focused on di-imine ligands and the luminescence behaviour arises due to metal to ligand charge transfer (MLCT) and halide to ligand charge transfer (XLCT). The complexes 1 and 2 are effective catalysts for the synthesis of 2-substituted benzoxazoles.

  4. Metallothionein-I/II Knockout Mice Aggravate Mitochondrial Superoxide Production and Peroxiredoxin 3 Expression in Thyroid after Excessive Iodide Exposure

    Directory of Open Access Journals (Sweden)

    Na Zhang

    2015-01-01

    Full Text Available Purpose. We aim to figure out the effect of metallothioneins on iodide excess induced oxidative stress in the thyroid. Methods. Eight-week-old MT-I/II knockout (MT-I/II KO mice and background-matched wild-type (WT mice were used. Mitochondrial superoxide production and peroxiredoxin (Prx 3 expression were measured. Results. In in vitro study, more significant increases in mitochondrial superoxide production and Prx 3 expression were detected in the MT-I/II KO groups. In in vivo study, significantly higher concentrations of urinary iodine level were detected in MT-I/II KO mice in 100 HI group. Compared to the NI group, there was no significant difference existing in serum thyroid hormones level in either groups (P>0.05, while the mitochondrial superoxide production was significantly increased in 100 HI groups with significantly increased LDH activity and decreased relative cell viability. Compared to WT mice, more significant changes were detected in MT-I/II KO mice in 100 HI groups. No significant differences were detected between the NI group and 10 HI group in both the MT-I/II KO and WT mice groups (P>0.05. Conclusions. Iodide excess in a thyroid without MT I/II protection may result in strong mitochondrial oxidative stress, which further leads to the damage of thyrocytes.

  5. Magnesium-induced copper-catalyzed synthesis of unsymmetrical diaryl chalcogenide compounds from aryl iodide via cleavage of the Se-Se or S-S bond.

    Science.gov (United States)

    Taniguchi, Nobukazu; Onami, Tetsuo

    2004-02-06

    The methodology for a copper-catalyzed preparation of diaryl chalcogenide compounds from aryl iodides and diphenyl dichalcogenide molecules is reported. Unsymmetrical diaryl sulfide or diaryl selenide can be synthesized from aryl iodide and PhYYPh (Y = S, Se) with a copper catalyst (CuI or Cu(2)O) and magnesium metal in one pot. This reaction can be carried out under neutral conditions according to an addition of magnesium metal as the reductive reagent. Furthermore, it is efficiently available for two monophenylchalcogenide groups generated from diphenyl dichalcogenide.

  6. Radioactive Iodide (131I Excretion Profiles in Response to Potassium Iodide (KI and Ammonium Perchlorate (NH4ClO4 Prophylaxis

    Directory of Open Access Journals (Sweden)

    Jeffrey Fisher

    2012-08-01

    Full Text Available Radioactive iodide (131I protection studies have focused primarily on the thyroid gland and disturbances in the hypothalamic-pituitary-thyroid axis. The objective of the current study was to establish 131I urinary excretion profiles for saline, and the thyroid protectants, potassium iodide (KI and ammonium perchlorate over a 75 hour time-course. Rats were administered 131I and 3 hours later dosed with either saline, 30 mg/kg of NH4ClO4 or 30 mg/kg of KI. Urinalysis of the first 36 hours of the time-course revealed that NH4ClO4 treated animals excreted significantly more 131I compared with KI and saline treatments. A second study followed the same protocol, but thyroxine (T4 was administered daily over a 3 day period. During the first 6–12 hour after 131I dosing, rats administered NH4ClO4 excreted significantly more 131I than the other treatment groups. T4 treatment resulted in increased retention of radioiodide in the thyroid gland 75 hour after 131I administration. We speculate that the T4 treatment related reduction in serum TSH caused a decrease synthesis and secretion of thyroid hormones resulting in greater residual radioiodide in the thyroid gland. Our findings suggest that ammonium perchlorate treatment accelerates the elimination rate of radioiodide within the first 24 to 36 hours and thus may be more effective at reducing harmful exposure to 131I compared to KI treatment for repeated dosing situations. Repeated dosing studies are needed to compare the effectiveness of these treatments to reduce the radioactive iodide burden of the thyroid gland.

  7. High-Performance Doped Strontium Iodide Crystal Growth Using a Modified Bridgman Method

    Science.gov (United States)

    Rowe, Emmanuel

    dipole-allowed and thus are about 106 times stronger than the more frequently observed 4f-4f transition in the trivalent rare earth ions. Ce3+, Nd3+ and Pr3+ have been investigated for fast response applications while Ce3+, Eu 2+, and Yb2+ stand out as the most promising activators offering high light yield, and high energy resolution. Using a modified Bridgman growth technique we have grown crystals with a low energy resolution of 2.6% at 662 keV, which is lower than the previous 2.8% reported for SrI2:Eu 2+. The modified technique (called so for its vertical crystal growth orientation) is necessary due to the anisotropic thermal expansion coefficient of Strontium Iodide. The problem plaguing the growth of the crystal is spontaneous cracking, which usually appear during cooling in the bulk. With the use of a zone separating shield, one can achieve more control of the temperature gradient between the two zones without compromising the actual temperature of the two zones. Additionally the use of codopants, in particular divalent magnesium improved the crystalline quality by acting as a gathering for iodine ions, which led to reduction of defect density.

  8. Simultaneous determination of perfluoroalkyl iodides, perfluoroalkane sulfonamides, fluorotelomer alcohols, fluorotelomer iodides and fluorotelomer acrylates and methacrylates in water and sediments using solid-phase microextraction-gas chromatography/mass spectrometry.

    Science.gov (United States)

    Bach, Cristina; Boiteux, Virginie; Hemard, Jessica; Colin, Adeline; Rosin, Christophe; Munoz, Jean-François; Dauchy, Xavier

    2016-05-27

    Here, we developed and validated a headspace-solid-phase microextraction-gas chromatography/mass spectrometry (HS-SPME-GC/MS) method for the determination of 14 volatile perfluorinated alkylated substances (PFASs) in water and sediment samples according to SANTE 11945/2015 guidelines. Three fluorotelomer alcohols (FTOHs), two perfluoroalkyl iodides (PFIs), three fluorotelomer iodides (FTIs), four fluorotelomer acrylates and methacrylates (FTACs and FTMACs) and two perfluoroalkyl sulfonamides (FASAs) were analysed simultaneously to assess the occurrence of these compounds from their emission sources to the outlets in water treatment plants. Several SPME parameters were optimised for both water and sediment to maximise responses and keep analysis time to a minimum. In tap water, the limits of quantification (LOQs) were found to be between 20ng/L and 100ng/L depending on the analyte, with mean recoveries ranging from 76 to 126%. For sediments, LOQs ranged from 1 to 3ng/g dry weight depending on the target compound, with mean recoveries ranging from 74 to 125%. SPME considerably reduced sample preparation time and its use provided a sensitive, fast and simple technique. We then used this HS-SPME-GC/MS method to investigate the presence of volatile PFASs in the vicinity of an industrial facility. Only 8:2 FTOH and 10:2 FTOH were detected in a few water and sediment samples at sub-ppb concentration levels. Moreover, several non-target fluorotelomers (12:2 FTOH, 14:2 FTOH and 10:2 FTI) were identified in raw effluent samples. These long-chain fluorotelomers have high bioaccumulative potential in the aquatic environment compared with short-chain fluorotelomers such as 6:2 FTOH and 6:2 FTI.

  9. DEVELOPMENT OF AN IN VITRO RADIOACTIVE IODIDE UPTAKE ASSAY (RAIU) WITH HUMAN NIS-EXPRESSING HEK293T-EPA CELL LINE

    Science.gov (United States)

    Many high-throughput screening (HTPS) assays are available in the US EPA ToxCast program for estrogen and androgen pathways; only a limited number of assays exist for thyroid pathways. One potential target of thyroid-disrupting chemicals is the active uptake of iodide into the t...

  10. Isobaric Heat Capacities of Micelle Formation by 1-Methyl-4-n-dodecylpyridinium Iodide in Aqueous Solution; Effects of Added Urea

    NARCIS (Netherlands)

    Posthumus, Willem; Engberts, Jan B.F.N.; Bijma, Koos; Blandamer, Michael J.

    1997-01-01

    Over the temperature range from 303 to 333 K, the enthalpy of micelle formation by 1-methyl-4-n-dodecylpyridinium iodide in aqueous solution is exothermic, characterised by an isobaric heat capacity of micelle formation equal to -439 ± 10 J K-1 mol-1. At 303 K, the critical micellar concentration (2

  11. The Effect of Temperature and Ionic Strength on the Oxidation of Iodide by Iron(III) : A Clock Reaction Kinetic Study

    NARCIS (Netherlands)

    Bauer, Jurica; Tomisic, Vladislav; Vrkljan, Petar B. A.

    2012-01-01

    A laboratory exercise has recently been reported in which the students use the initial rates method based on the clock reaction approach to deduce the rate law and propose a reaction mechanism for the oxidation of iodide by iron(III) ions. The same approach is used in the exercise proposed herein; t

  12. Differential effects of natural flavonoids on growth and iodide content in a human NA+/I_symporter-transfecred follicular thyroid carcinoma cell line

    NARCIS (Netherlands)

    Schroder-van der Elst, J.P.; Heide, van der D.; Romijn, J.A.; Smit, J.W.A.

    2004-01-01

    OBJECTIVE: Natural flavonoids (plant pigments) have been shown to inhibit thyroid peroxidase (TPO) in vitro and the growth of thyroid cancer cell lines. We have studied the role of flavonoids on the iodide transport and the growth of the human follicular thyroid cancer cell line (FTC133) which was s

  13. Iodide-induced organothiol desorption and photochemical reaction, gold nanoparticle (AuNP) fusion, and SERS signal reduction in organothiol-containing AuNP aggregates

    Science.gov (United States)

    Gold nanoparticles (AuNPs) have been used extensively as surface-enhanced Raman spectroscopic (SERS) substrates for their large SERS enhancements and widely believed chemical stability. Presented is the finding that iodide can rapidly reduce the SERS intensity of the ligands, including organothiols ...

  14. The thyroxine-containing thyroglobulin peptide (aa 2549-2560) is a target epitope in iodide-accelerated spontaneous autoimmune thyroiditis.

    Science.gov (United States)

    Kolypetri, Panayota; Carayanniotis, Karen; Rahman, Shofiur; Georghiou, Paris E; Magafa, Vassiliki; Cordopatis, Paul; Carayanniotis, George

    2014-07-01

    Enhanced iodide ingestion is known to accelerate the incidence and severity of spontaneous autoimmune thyroiditis [iodide-accelerated spontaneous autoimmune thyroiditis (ISAT)] in NOD.H2(h4) mice. CD4+ cells are required for the development and maintenance of ISAT, but their target epitopes remain unknown. In this study, we show that the previously identified thyroglobulin (Tg) T cell epitope p2549-2560 containing thyroxine at position 2553 (T4p2553) induces thyroiditis as well as strong specific T and B cell responses in NOD.H2(h4) mice. In ISAT, activated CD4+ T cells specific for T4p2553 are detected before the disease onset in thyroid-draining cervical lymph nodes only in mice placed on an iodide-rich diet and not in age-matched controls. In addition, selective enrichment of CD4+ IFN-γ+ T4p2553-specific cells is observed among cervical lymph node cells and intrathyroidal lymphocytes. T4p2553 was equally detectable on dendritic cells obtained ex vivo from cervical lymph node cells of NaI-fed or control mice, suggesting that the iodide-rich diet contributes to the activation of autoreactive cells rather than the generation of the autoantigenic epitope. Furthermore, spontaneous T4p2553-specific IgG are not detectable within the strong Tg-specific autoantibody response. To our knowledge, these data identify for the first time a Tg T cell epitope as a spontaneous target in ISAT.

  15. The pan-DAC inhibitor LBH589 is a multi-functional agent in breast cancer cells: cytotoxic drug and inducer of sodium-iodide symporter (NIS).

    Science.gov (United States)

    Fortunati, N; Catalano, M G; Marano, F; Mugoni, V; Pugliese, M; Bosco, O; Mainini, F; Boccuzzi, G

    2010-12-01

    New drugs with anti-tumor activity, also able to modify the expression of selected molecules, are under evaluation in breast cancer which is becoming resistant to conventional treatment, or in metastatic disease. The sodium-iodide symporter (NIS), which mediates iodide uptake into thyroid cells, and is the molecular basis of radioiodine imaging and therapy in thyroid cancer, is also expressed in a large portion of breast tumors. Since NIS expression in breast cancer is not sufficient for a significant iodide uptake, drugs able to induce its expression and correct function are under evaluation. In the present study, we report for the first time that the pan-deacetylase (DAC) inhibitor LBH589 (panobinostat) significantly induced NIS, both as mRNA and as protein, through the increase of NIS promoter activity, with the final consequence of obtaining a significant up-take of iodide in MCF7, T47D, and MDA-MB231 breast cancer cells. Moreover, we observed that LBH589 causes a significant reduction in cell viability of estrogen-sensitive and -insensitive breast cancer cells within nanomolar range. The anti-tumor effect of LBH589 is sustained by apoptosis induction and cell cycle arrest in G(2)/M. In conclusion, our data suggest that LBH589 might be a powerful tool in the management of breast cancer due to its multiple effects and support a potential application of LBH589 in the diagnosis and treatment of this disease.

  16. Dynamics of dipole- and valence bound anions in iodide-adenine binary complexes: A time-resolved photoelectron imaging and quantum mechanical investigation.

    Science.gov (United States)

    Stephansen, Anne B; King, Sarah B; Yokoi, Yuki; Minoshima, Yusuke; Li, Wei-Li; Kunin, Alice; Takayanagi, Toshiyuki; Neumark, Daniel M

    2015-09-14

    Dipole bound (DB) and valence bound (VB) anions of binary iodide-adenine complexes have been studied using one-color and time-resolved photoelectron imaging at excitation energies near the vertical detachment energy. The experiments are complemented by quantum chemical calculations. One-color spectra show evidence for two adenine tautomers, the canonical, biologically relevant A9 tautomer and the A3 tautomer. In the UV-pump/IR-probe time-resolved experiments, transient adenine anions can be formed by electron transfer from the iodide. These experiments show signals from both DB and VB states of adenine anions formed on femto- and picosecond time scales, respectively. Analysis of the spectra and comparison with calculations suggest that while both the A9 and A3 tautomers contribute to the DB signal, only the DB state of the A3 tautomer undergoes a transition to the VB anion. The VB anion of A9 is higher in energy than both the DB anion and the neutral, and the VB anion is therefore not accessible through the DB state. Experimental evidence of the metastable A9 VB anion is instead observed as a shape resonance in the one-color photoelectron spectra, as a result of UV absorption by A9 and subsequent electron transfer from iodide into the empty π-orbital. In contrast, the iodide-A3 complex constitutes an excellent example of how DB states can act as doorway state for VB anion formation when the VB state is energetically available.

  17. Copper iodide nanoparticles on poly(4-vinylpyridine): A new and efficient catalyst for the synthesis of 1,8-dioxooctahydroxanthenes under solvent-free conditions

    Indian Academy of Sciences (India)

    Jalal Albadi; Mosadegh Keshavarz; Masoumeh Abedini; Moloud Khoshakhlagh

    2013-03-01

    Poly(4-vinylpyridine)-supported nanoparticles of copper(I) iodide is reported as a new, efficient and recyclable catalyst for the synthesis of 1,8-dioxooctahydroxanthenes under solvent-free conditions. This catalyst can be recovered by simple filtration and recycled up to 10 consecutive runs without losing of its efficiency.

  18. Iodine-water-alkanol and potassium iodide-water-alkanol systems: Phase diagrams and regularities of association according to IR and NMR spectroscopic data

    Science.gov (United States)

    Monakhova, Yu. B.; Varlamova, T. M.; Rubtsova, E. M.; Mushtakova, S. P.

    2015-04-01

    The variation of the iodine and potassium iodide solubilities in water-monoatomic alcohol (ethanol, propanol, isopropanol) solvents is considered from the standpoint of IR spectroscopic and chemometric data on association in water-alkanol binary mixtures. The iodine and potassium iodide solubilities in the mixed solvents vary nonlinearly with solvent composition because of the formation of 1 : 1 and 1 : 3 water-alcohol heteroassociates and alcohol homoassociates. Different kinds of phase diagram are observed for the iodine-water-alcohol systems: the I2-H2O-1-C3H7OH and the I2-H2O-2-C3H7OH diagrams have a phase separation region, while the I2-H2O-C2H5OH diagram does not. This fact is explained in terms of the interaction between the components of the systems. The variation of the potassium iodide solubility in the mixed solvent is discussed: a decrease in the KI solubility is symbatic to an increase in the relative concentration of 1 : 1 associates in the water-alcohol solution. The run of the iodine and potassium iodide solubility curves at low alcohol concentrations is explained on the basis of NMR spectroscopic data on association in aqueous solutions of the monoatomic alcohols.

  19. Cul-catalyzed Coupling Reactions of Aryl Iodides with Amides Using L-Proline and KF/Al2O3

    Institute of Scientific and Technical Information of China (English)

    HOSSEINZADEH Rahman; TAJBAKHSH Mahmood; MOHADJERANI Maryam; GHORBANI Elham

    2008-01-01

    An efficient experimentally simple and inexpensive catalyst system for the selective amidation of aryl iodides using 15 mol% of Cul as catalyst,15 mol% of L-proline as ligand and KF/Al2O3 as a base in toluene is described.

  20. Copper-catalysed N-arylation of arylsulfonamides with aryl bromides and aryl iodides using KF/Al2O3

    Indian Academy of Sciences (India)

    Rahman Hosseinzadeh; Mahmood Tajbakhsh; Maryam Mohadjerani; Mohammad Alikarami

    2010-03-01

    An efficient synthesis of -arylsulfonamides with a variety of aryl bromides, aryl iodides and heteroaryl bromides using KF/Al2O3 as a suitable base, CuI as an inexpensive catalyst and ,'-dimethylethylenediamine (,'-DMEDA) as an effective ligand is described.

  1. Synergistic effect of iodide ions on the corrosion inhibition of steel in 0.5 M H 2SO 4 by new chalcone derivatives

    Science.gov (United States)

    Bouklah, M.; Hammouti, B.; Aouniti, A.; Benkaddour, M.; Bouyanzer, A.

    2006-07-01

    The effect of addition of 4',4-dihydroxychalcone (P 1), 4-aminochalcone (P 2) and 4-bromo, 4'-methoxychalcone (P 3) on the corrosion of steel in 0.5 M sulphuric acid has been studied by weight loss measurements, potentiodynamic and EIS measurements. We investigate the synergistic effect of iodide ions on the corrosion inhibition of steel in the presence of chalcone derivatives. The corrosion rates of the steel decrease with the increase of the chalcones concentration, while the inhibition efficiencies increase. The addition of iodide ions enhances the inhibition efficiency considerably. The presence of iodide ions increases the degree of surface coverage. The synergism parameters SΘ and SI, calculated from surface coverage and the values of inhibition efficiency, in the case of chalcone derivatives are found to be larger than unity. The enhanced inhibition efficiency in the presence of iodide ions is only due to synergism and there is a definite contribution from the inhibitors molecules. E (%) obtained from the various methods is in good agreement. Polarisation measurements show also that the compounds act as cathodic inhibitors.

  2. "Molecular beacon"-hosted thioflavin T: Applications for label-free fluorescent detection of iodide and logic operations.

    Science.gov (United States)

    Li, Yan-Yun; Jiang, Xiao-Qin; Lu, Ling-Fei; Zhang, Min; Shi, Guoyue

    2016-04-01

    In this work, we presented a simple, label-free and rapid-responsive fluorescence assay for iodide (I(-)) detection based on "molecular beacon (MB)"-hosted thioflavin T (ThT), achieving a limit of detection as low as 158 nM. The proposed method exhibited very good selectivity to I(-) ions over other anions interference due to the strong binding force between I(-) ions with Hg(2+). Upon the addition of I(-) ions, it would capture Hg(2+) from a T-Hg(2+)-T complex belonging to the MB-like DNA hairpin structure, which eventually quenched the initial fluorescence as output. In addition, it was successfully applied for operation of an integrated DNA logic gate system and to the determination of I(-) in real samples such as human urine.

  3. LiI-doped N,N-dimethyl-pyrrolidinium iodide, an archetypal rotator-phase ionic conductor.

    Science.gov (United States)

    Adebahr, Josefina; Seeber, Aaron J; MacFarlane, Douglas R; Forsyth, Maria

    2005-11-03

    N,N-Dimethyl-pyrrolidinium iodide, and the effect of doping with LiI, has been investigated using DSC, NMR, and impedance spectroscopy. It was found that the addition of a small amount of LiI enhances the ionic conductivity by up to 3 orders of magnitude for this ionic solid. Furthermore, a slight decrease in phase transition onset temperatures, as well as the appearance of a superimposed narrow line in the (1)H NMR spectra with dopant, suggest that the LiI facilitates the mobility of the matrix material, possibly by the introduction of vacancies within the lattice. (7)Li NMR line width measurements reveal a narrow Li line width, decreasing in width and increasing in intensity with temperature, indicating mobile Li ions.

  4. Structural and ionic conductivity behavior in hydroxypropylmethylcellulose (HPMC) polymer films complexed with sodium iodide (NaI)

    Science.gov (United States)

    Rani, N. Sandhya; Sannappa, J.; Demappa, T.; Mahadevaiah

    2013-02-01

    Solid polymer electrolyte films based on Hydroxypropylmethylcellulose (HPMC) complexed with Sodium Iodide (NaI) were prepared using solution cast method. The dissolution of the salt into the polymer host and the micro structural properties of pure and NaI complexed HPMC polymer electrolyte films were confirmed by X - Ray diffraction (XRD) studies. The XRD results revealed that the amorphous domains of HPMC polymer matrix was increased with increase in the NaI salt concentration. The degree of crystallanity and crystallite size is high for pure HPMC samples. Direct current (dc) conductivity was measured in the temperature range of 313-383k. Temperature dependence of dc electrical conductivity and activation energy regions data indicated the dominance of ion type charge transport in these polymer electrolyte films.

  5. Conductivity study and fourier transform infrared (FTIR) characterization of methyl cellulose solid polymer electrolyte with sodium iodide conducting ion

    Energy Technology Data Exchange (ETDEWEB)

    Abiddin, Jamal Farghali Bin Zainal [Faculty of Applied Sciences, Universiti Teknologi MARA, 40450 Shah Alam, Selangor D.E. (Malaysia); Ahmad, Azizah Hanom [Faculty of Applied Sciences, Universiti Teknologi MARA, 40450 Shah Alam, Selangor D.E. (Malaysia); Institute of Science, Universiti Teknologi MARA, 40450 Shah Alam, Selangor D.E. (Malaysia)

    2015-08-28

    Sodium ion (Na{sup +}) based solid polymer electrolyte (SPE) has been prepared using solution cast technique with distilled water as solvent and Methylcellulose (MC) as a polymer host. Methylcellulose polymer was chosen as the polymer host due to the abundance of lone pair electrons in the carbonyl and C-O-C constituents, which in turn provide multiple hopping sites for the Na{sup +} conducting ions. Variable compositions of sodium iodide (NaI) salt were prepared to investigate the optimum MC-NaI weight ratio. Results from Electrical Impedance Spectroscopy (EIS) technique show that pure methylcellulose has a low conductivity of 3.61 × 10{sup −11} S/cm.The conductivity increases as NaI content increases up to optimum NaIcomposition of 40 wt%, which yields an average conductivity of 2.70 × 10{sup −5} S/cm.

  6. A study on optical properties of poly (ethylene oxide) based polymer electrolyte with different alkali metal iodides

    Science.gov (United States)

    Rao, B. Narasimha; Suvarna, R. Padma

    2016-05-01

    Polymer electrolytes were prepared by adding poly (ethylene glycol) dimethyl ether (PEGDME), TiO2 (nano filler), different alkali metal iodide salts RI (R+=Li+, Na+, K+, Rb+, Cs+) and I2 into Acetonitrile gelated with Poly (ethylene oxide) (PEO). Optical properties of poly (ethylene oxide) based polymer electrolytes were studied by FTIR, UV-Vis spectroscopic techniques. FTIR spectrum reveals that the alkali metal cations were coordinated to ether oxygen of PEO. The optical absorption studies were made in the wavelength range 200-800 nm. It is observed that the optical absorption increases with increase in the radius of alkali metal cation. The optical band gap for allowed direct transitions was evaluated using Urbach-edges method. The optical properties such as optical band gap, refractive index and extinction coefficient were determined. The studied polymer materials are useful for solar cells, super capacitors, fuel cells, gas sensors etc.

  7. Polarization and Dielectric Study of Methylammonium Lead Iodide Thin Film to Reveal its Nonferroelectric Nature under Solar Cell Operating Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hoque, Md Nadim Ferdous; Yang, Mengjin; Li, Zhen; Islam, Nazifah; Pan, Xuan; Zhu, Kai; Fan, Zhaoyang

    2016-07-08

    Researchers have debated whether methylammonium lead iodide (MAPbI3), with a perovskite crystal structure, is ferroelectric and therefore contributes to the current--voltage hysteresis commonly observed in hybrid perovskite solar cells (PSCs). We thoroughly investigated temperature-dependent polarization, dielectric, and impedance spectroscopies, and we found no evidence of ferroelectric effect in a MAPbI3 thin film at normal operating conditions. Therefore, the effect does not contribute to the hysteresis in PSCs, whereas the large component of ionic migration observed may play a critical role. Our temperature-based polarization and dielectric studies find that MAPbI3 exhibits different electrical behaviors below and above ca. 45 degrees C, suggesting a phase transition around this temperature. In particular, we report the activation energies of ionic migration for the two phases and temperature-dependent permittivity of MAPbI3. This study contributes to the understanding of the material properties and device performance of hybrid perovskites.

  8. The Synthesis of 1-Ethyl-1'-(4-vinylbenzyl)-4, 4'-bipyridinium Chloride and Iodide and its Electrochromic Property

    Institute of Scientific and Technical Information of China (English)

    Qing Long JIANG; Xiang Kai FU; Zhu Jun CHEN

    2006-01-01

    A new compound 1-ethyl-1'-(4-vinylbenzyl)-4, 4'-bipyridinium chloride and iodide has been synthesized. The cyclic voltammogram and impedance spectra indicated that a layer of viologen's electrochromic (EC) film could be deposited on conductive ITO glass working electrode.With polyelectrolyte as ionic conduction layer, solid EC devices based on this compound have been assembled and their thickness was about 2.35 mm. When different voltages were added,they showed blue or violet red color. After optimization, its response time was less than 50 ms,the number of redox circulation was over 107 and the color of coloration states could be kept for 3days. This kind of EC device can meet the demand of electronic ink.

  9. Methyl Iodide Accelerated Asymmetric Epoxidation of Alkenes Catalyzed by Chiral Salen-Mn(Ⅲ) Complexes with Tertiary Amine Units

    Institute of Scientific and Technical Information of China (English)

    SUN,Yang; TANG,Ning

    2007-01-01

    A series of chiral salen-Mn(Ⅲ) complexes featuring two tertiary amine units were synthesized and employed in the enantioselective epoxidation of unfunctionalized alkenes in the presence of pyridine N-oxide and 2,6-dimethylpyridine N-oxide as proximal ligands, respectively. Moderate to high enantioselectivity and acceptable yields were achieved when NaClO was used as terminal oxidant under CH2Cl2/H2O biphasic media. Methyl iodide was found to be an effective additive to accelerate the epoxidation, possibly owing to the formation of quaternary ammonium units on catalysts, which may facilitate the reaction in an oil/water biphasic medium. The subsequent stimulation experiment was carried out, and the resulting ESI-HRMS analysis revealed the formation of a novel(salen)manganese(Ⅲ) intermediate featuring two quaternary ammonium units, and bearing a pyridine N-oxide and a molecule of water simultaneously axially-coordinated backbone.

  10. Enhancement of gaseous iodine emission by aqueous ferrous ions during the heterogeneous reaction of gaseous ozone with aqueous iodide.

    Science.gov (United States)

    Sakamoto, Yosuke; Enami, Shinichi; Tonokura, Kenichi

    2013-04-11

    Gaseous I2 formation from the heterogeneous reaction of gaseous ozone with aqueous iodide in the presence of aqueous ferrous ion (Fe(2+)) was investigated by electron impact ionization mass spectrometry. Emission of gaseous I2 increased as a function of the aqueous FeCl2 concentration, and the maximum I2 formation with Fe(2+) was about 10 times more than without Fe(2+). This enhancement can be explained by the OH(-) scavenging by Fe(3+) formed from Fe(2+) ozonation to produce colloidal Fe(OH)3. This mechanism was confirmed by measurements of aqueous phase products using a UV-vis spectrometer and an electrospray ionization mass spectrometer. We infer that such a pH-buffering effect may play the key role in general halogen activations.

  11. Uptake and translocation of labelled iodide ion in privet (Ligustrum vulgare L. as related to its defoliating activity

    Directory of Open Access Journals (Sweden)

    S. Marczyński

    2015-06-01

    Full Text Available The 131J- ion applied as KJ solution to lanolin ring on the leaf moved quickly to other parts of the leaf, however, it was transported to the stem and axillary bud in small amount. The 131J- ion from potassium iodide was absorbed very fast by privet (Ligustrum vulgare L.. By 45 min after treatment about half of the applied ion was absorbed. This result was also confirmed In field experiments with non labelled KJ with privet and with Spiraea x bumalda cv. Froebelii during 2 year experiments. In the conditions of high air humidity (95% r.h. much more K131J was absorbed than at low air humidity (50% r.h. at the same temperature (23°. Also at a relatively high temperature (23° the uptake was more intensive than at a low temperature (4°, at the same air humidity (95% r.h..

  12. Synthesis, crystal growth and characterizations of bis ( l-proline) cadmium iodide: a new semi-organic nonlinear optical material

    Science.gov (United States)

    Boopathi, K.; Jagan, R.; Ramasamy, P.

    2016-07-01

    Novel semi-organic single crystals of bis ( l-proline) cadmium iodide (BLPC) were grown by slow evaporation technique. The crystal structure was determined by single-crystal X-ray diffraction studies. Single-crystal X-ray diffraction study shows that [BLPC] crystallizes in orthorhombic system with space group P212121. 1H NMR and 13C NMR studies were conducted for the grown crystal. Functional groups present in the compound were identified by FTIR spectral studies. The UV-Vis-NIR spectrum was studied to analyse the optical properties of the grown crystals. Thermogravimetric analysis was carried out to study thermal behaviour of the materials. Vickers microhardness measurement was carried out for different loads. Etching studies were carried out using water as etchant. The second harmonic generation efficiency was determined by the Kurtz powder method and it was found to be higher than that of potassium dihydrogen phosphate.

  13. Age-dependent potassium iodide effect on the thyroid irradiation by 131I and 133I in the nuclear emergency.

    Science.gov (United States)

    Jang, M; Kim, H K; Choi, C W; Kang, C S

    2008-01-01

    The initial near-field exposure is primarily through inhalation in a nuclear emergency and the dominant contribution to the effective inhalation dose comes from radioiodine. Thyroid blockade by oral potassium iodide (KI) is efficient and practical for public in the nuclear emergency. Age-dependent radioprotective effect of KI on the thyroid irradiation by (131)I and (133)I has been derived using the simplified compartment model of iodine metabolism and WinSAAM program. Administration of KI within 2 h after (131)I and (133)I intake can block thyroid uptake significantly, yielding protective effect of 78.9% and 74.3%, respectively, for (131)I and (133)I for adults. The mean absorbed doses decrease with age, while protective effects of KI are similar for all age groups.

  14. Synthesis, crystal growth and characterization of a chiral compound (triphenylphosphine oxide cadmium iodide): A new semiorganic nonlinear optical material

    Science.gov (United States)

    Santhakumari, R.; Ramamurthi, K.; Stoeckli-Evans, Helen; Hema, R.; Nirmala, W.

    2011-05-01

    Synthesis of semiorganic material, triphenylphosphine oxide cadmium iodide (TPPOCdI), is reported for the first time. Employing the temperature reduction method, a crystal of size 16×7×6 mm 3 was grown from dimethyl sulfoxide (DMSO) solution. Three dimensional crystal structure of the grown crystal was determined by single crystal X-ray diffraction study. The complex crystallizes in the chiral orthorhombic space group P2 12 12 1. FTIR study was carried out in order to confirm the presence of the functional groups. UV-vis-NIR spectral studies show that the crystal is transparent in the wavelength range of 290-1100 nm. The microhardness test was carried out, and the load hardness was measured. Thermogravimetric and differential thermal analyses reveal the thermal stability of the crystal. Second harmonic generation efficiency of the powdered TPPOCdI, tested using Nd: YAG laser, is ∼0.65 times that of potassium dihydrogen orthophosphate.

  15. High Momentum Particle Identification Detector The Study of Cesium Iodide Quantum Efficiency Dependency on Substrate Material, Temperature and Quartz Window

    CERN Document Server

    Wisna, Gde Bimananda M

    2014-01-01

    The Cesium Iodide (CsI) is used as a material for detecting Cherenkov radiation produced by high momentum particle in High Momentum Particle Identification Detector (HMPID) at ALICE Experiment at CERN. This work provides investigation and analysis of The Quantum Efficiency (QE) result of CsI which is deposited on five samples substrates such as copper passivated red, copper passivated yellow, aluminium, copper coated with nickel and copper coated with nickel then coated with gold. The measurement of five samples is held under temperature $60^{0}$ C and $25^{0}$ C (room temperature) and also with optical quartz window which can be adjusted to limit the wavelength range which reach the CsI. The result shows there are dependency of substrate, temperature due to enhancement effect and also quartz windows usage on QE of CsI. The results of five samples is then compared and analyzed.

  16. Modeling high speed growth of large rods of cesium iodide crystals by edge-defined film-fed growth (EFG)

    Science.gov (United States)

    Yeckel, Andrew

    2016-09-01

    A thermocapillary model of edge-defined film-fed growth (EFG) is developed to analyze an experimental system for high speed growth of cesium iodide as a model system for halide scintillator production. The model simulates heat transfer and fluid dynamics in the die, melt, and crystal under conditions of steady growth. Appropriate mass, force, and energy balances are used to compute self-consistent shapes of the growth interface and melt-vapor meniscus. The model is applied to study the effects of growth rate, die geometry, and furnace heat transfer on the limits of system operability. An inverse problem formulation is used to seek operable states at high growth rates by adjusting the overall temperature level and thermal gradient in the furnace. The model predicts that steady growth is feasible at rates greater than 20 mm/h for crystals up to 18 mm in diameter under reasonable furnace gradients.

  17. A New Synthetic Method of Rhodium Iodide%三碘化铑的新合成方法

    Institute of Scientific and Technical Information of China (English)

    刘桂华; 匡飞平; 潘再富; 余尧; 侯文明; 沈善问; 高金翠; 杨军; 彭玉玲; 杨善晓

    2012-01-01

    A new method has been introduced to synthesize rhodium iodide, an important homogenous catalyst for earbonylation of methanol, to overcome shortcomings of the present methods. These shortcomings include low yield, poor quality and unacceptability with respect to industrial manufacturing. The new method involves the direct reaction of RhC13 with HI. The yield is up to 98.5% and Cl-ean be minimized to 50 ppm by optimizing synthetic operations, superior to the reported data.%三氯化铑与氢碘酸直接合成碘化铑,在最佳反应条件下,合成的收率达到98.5%,产品晶形均一,氯离子含量小于50 mg/kg。

  18. A colorimetric assay for measuring iodide using Au@Ag core–shell nanoparticles coupled with Cu{sup 2+}

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, Jingbin, E-mail: xmuzjb@163.com [State Key Laboratory of Heavy Oil Processing & College of Science, China University of Petroleum (East China), Qingdao 266555 (China); Cao, Yingying [State Key Laboratory of Heavy Oil Processing & College of Science, China University of Petroleum (East China), Qingdao 266555 (China); Lu, Chun-Hua [The Key Laboratory of Analysis and Detection Technology for Food Safety of the MOE, College of Chemistry, Fuzhou University, Fuzhou 350002 (China); Wang, Xu-dong [Karlsruhe Institute of Technology (KIT), Institute for Biological Interfaces (IBG-1), Hermann-von-Helmholtz-Platz, 76344 Eggenstein-Leopoldshafen (Germany); Wang, Qianru; Wen, Cong-ying; Qu, Jian-Bo; Yuan, Cunguang [State Key Laboratory of Heavy Oil Processing & College of Science, China University of Petroleum (East China), Qingdao 266555 (China); Yan, Zi-feng, E-mail: zfyancat@upc.edu.cn [State Key Laboratory of Heavy Oil Processing & College of Science, China University of Petroleum (East China), Qingdao 266555 (China); Chen, Xi [Department of Chemistry and the MOE Key Laboratory of Spectrochemical Analysis & Instrumentation, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China)

    2015-09-03

    Au@Ag core–shell nanoparticles (NPs) were synthesized and coupled with copper ion (Cu{sup 2+}) for the colorimetric sensing of iodide ion (I{sup −}). This assay relies on the fact that the absorption spectra and the color of metallic core–shell NPs are sensitive to their chemical ingredient and dimensional core-to-shell ratio. When I{sup −} was added to the Au@Ag core–shell NPs-Cu{sup 2+} system/solution, Cu{sup 2+} can oxidize I{sup −} into iodine (I{sub 2}), which can further oxidize silver shells to form silver iodide (AgI). The generated Au@AgI core–shell NPs led to color changes from yellow to purple, which was utilized for the colorimetric sensing of I{sup −}. The assay only took 10 min with a lowest detectable concentration of 0.5 μM, and it exhibited excellent selectivity for I{sup −} over other common anions tested. Furthermore, Au@Ag core–shell NPs-Cu{sup 2+} was embedded into agarose gels as inexpensive and portable “test strips”, which were successfully used for the semi-quantitation of I{sup −} in dried kelps. - Highlights: • Au@Ag core–shell NPs were synthesized and coupled with Cu{sup 2+} for the colorimetric I{sup −} sensing. • This assay is simple, rapid and selective. • Au@Ag core–shell NPs-Cu{sup 2+} were embedded into agarose gels as test strips.

  19. Formation of iodinated disinfection by-products during oxidation of iodide-containing waters with chlorine dioxide.

    Science.gov (United States)

    Ye, Tao; Xu, Bin; Lin, Yi-Li; Hu, Chen-Yan; Lin, Lin; Zhang, Tian-Yang; Gao, Nai-Yun

    2013-06-01

    This study was to explore the formation of iodinated disinfection by-products (I-DBPs), including iodoform (CHI3), iodoacetic acid (IAA) and triiodoacetic acid (TIAA), when iodide-containing artificial synthesized waters and raw waters are in contact with chlorine dioxide (ClO2). Among the investigated I-DBPs, CHI3 was the major species during ClO2 oxidation in artificial synthesized waters. Impact factors were evaluated, including the concentrations of ClO2, iodide (I(-)), dissolved organic carbon (DOC) and pH. Formation of CHI3, IAA and TIAA followed an increasing and then decreasing pattern with increased ClO2 or DOC concentration. I-DBPs yield was significantly affected by solution pH. High concentrations of I-DBPs were generated under circumneutral conditions with the maximum formation at pH 8. The increase of I(-) concentration can increase I-DBPs yields, but the increment was suppressed when I(-) concentration was higher than 50 μM. When 100 μg/L I(-)and ClO2 (7.5-44.4 μM) were spiked to the raw water samples from Yangshupu and Minhang drinking water treatment plant, certain amounts of CHI3 and IAA were found under pH 7 and the concentrations were strongly correlated with ClO2 dosage and water qualities, however, no TIAA was detected. Finally, we investigated I-DBPs formation of 18 model compounds, including 4 carboxylic acids, 5 phenols and 8 amino acids, treating with ClO2 when I(-) was present. Results showed that most of these model compounds could form a considerable amount of I-DBPs, especially for propanoic acid, butanoic acid, resorcinol, hydroquinone, alanine, glutamic acid, phenylalanine and serine.

  20. Changes in the decontamination factor of cesium iodide on evaporation of a scrubbing solution in the Filtered Containment Venting System

    Energy Technology Data Exchange (ETDEWEB)

    Na, Young Su; Ha, Kwang Soon; Kim, Sungil; Cho, Song-Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    When the pressure in the containment building approaches a setting value, the FCVS(Filtered Containment Venting System) operates. The amount of steam and gas mixtures generated during a severe accident can be released into the FCVS. Non-condensable gases and fine aerosols can pass a scrubbing solution and the filters in the FCVS vessel. The decontaminated gases are finally discharged from the FCVS to the outside environment. Previous study observed that a scrubbing solution in the FCVS vessel was constantly evaporating owing to high-temperature steam released continuously from the containment building. A scrubbing solution in the FCVS vessel was completely evaporated at about 31 hours after the FCVS operation. Pool evaporation in the FCVS vessel can negatively affect the decontamination feature of the FCVS because it reduces the scrubbing depth for fission products in an aerosol form. This study carefully evaluated the decontamination factor of metal iodide aerosols especially cesium iodide (CsI), on a scrubbing solution in the FCVS. This paper summarizes the calculated results on the decontamination factor of CsI in the FCVS vessel, which was presented at the international OECD-NEA/NUGENIA-SARNET workshop. This study estimated the decontamination factor of CsI on a scrubbing solution in the FCVS. The MELCOR computer code simulated that an SBO occurred in the OPR 1000. The FCVS consists of a cylindrical vessel with a 3 m diameter and 6.5 m height, and it includes a scrubbing solution of 21 tons. Accumulated mass of CsI aerosol was calculated in a scrubbing solution and the atmosphere in the FCVS vessel and the outside environment. In the early FCVS operation, the decontamination factor of CsI aerosol rapidly increased owing to steam condensation in a scrubbing solution. When the temperature of a pool approached its saturation temperature, the decontamination factor of CsI aerosol started to decrease.

  1. Effects of meso-2,3-dimercaptosuccinic acid, potassium iodide and chlorophyll on lead accumulation in male mice

    Directory of Open Access Journals (Sweden)

    Ying Xie

    2017-02-01

    Full Text Available Objectives: Lead (Pb pollution is a serious public health problem all over the world, it especially plays severe damage role in children’s health. Apart from reducing lead-induced damages, the decrease of lead accumulation is also critical. This study has been the first attempt to investigate effects of meso-2,3-dimercaptosuccinic acid (DMSA, potassium iodide (KI and chlorophyll (Chl on lead accumulation in male mice. Material and Methods: Eighty healthy Kunming male mice were selected and divided randomly into 8 groups. They were treated with lead acetate (PbAc intraperitoneally, individually and in combination with the DMSA, KI or Chl once daily for 5 days. Meanwhile, the control group was treated with normal saline during the whole exposure period. On 30th day, mice were sacrificed and lead concentrations were detected in the whole blood, livers, kidneys, and testicles of mice by means of the graphite furnace atomic absorption spectrometry. Results: In comparison with the control group, lead concentrations increased in mice treated with the PbAc and DMSA, KI and Chl diminished lead accumulation in the whole blood, livers, and kidneys. Chl had specifically the same effects on lead concentrations in the testicles of male mice. Conclusions: Potassium iodide and Chl, as food additives, had the same effects as the DMSA to reduce lead accumulation in male mice effectively. Our results provided experimental evidence in vivo for the preventive measures of lead poisoning. Int J Occup Med Environ Health 2017;30(1:87–93

  2. Synthesis and Characterization of Iodine laden Graphene Nano Platelets via reduction of Graphene Oxide Using Hydrogen Iodide

    Science.gov (United States)

    Sundararaj, Joe Livingston

    This research thesis proposes a novel method for the synthesis, analysis and characterization of Iodinated X-Ray contrast agents using Graphene Nanoplatelets (GNPs) for Computed Tomographic Imaging. Graphene Oxide was synthesized using the Hummers Method of Oxidation [1] through oxidative treatment of Graphite with Potassium Permanganate (KMnO4). The resulting Graphene Oxide was chemically reduced using varying concentrations of Hydrogen Iodide or Hydroiodic acid (HI), rather than the conventionally used highly toxic Hydrazine Hydrate (N2H4) to strip off the oxygen functionalities. In the process of chemical reduction using Hydrogen Iodide, we hypothesized that this would result in the incorporation of Iodine into the Graphitic structure. Raman Spectroscopy, EDS along with XRD analysis provided evidence for the reduction of GO. Raman spectra for reduced GNPs showed an increase in ID/IG ratio from that of graphene oxide and also a peak at 154cm-1 attributed to I5 -. EDS/EDX spectra for HI reduced GO showed a peak at X-ray energy level 3.94KeV characteristic of Iodine. Further analysis using Ion-Selective Electrode measurements confirmed the presence of about 10% Iodine in the Hydroiodic acid reduced samples. SEM and TEM images showed a brief morphology of the Graphene Nanoplatelets. Finally, to elucidate the possibility of Iodinated GNPs to be developed into potential CT contrast agents in the near or far future, CT Phantoms of Iodine loaded GNPs at a concentration of 40mg/ml in water showed excellent contrast density with water and dilute Hydroiodic acid as controls.

  3. Changes in gastric sodium-iodide symporter (NIS) activity are associated with differences in thyroid gland sensitivity to perchlorate during metamorphosis.

    Science.gov (United States)

    Carr, James A; Murali, Sharanya; Hu, Fang; Goleman, Wanda L; Carr, Deborah L; Smith, Ernest E; Wages, Mike

    2015-08-01

    We investigated stage-dependent changes in sensitivity of the thyroid gland to perchlorate during development of African clawed frog tadpoles (Xenopus laevis) in relation to non-thyroidal iodide transporting tissues. Perchlorate-induced increases in thyroid follicle cell size and colloid depletion were blunted when exposures began at Nieuwkoop-Faber (NF) stage 55 compared to when exposures began at NF stages 49 or 1-10. To determine if the development of other iodide transporting tissues may contribute to this difference we first examined which tissues expressed transcripts for the sodium dependent iodide symporter (NIS). RT-PCR analysis revealed that NIS was expressed in stomach and small intestine in addition to the thyroid gland of X. laevis tadpoles. NIS mRNA was not detected in lung, kidney, skin, gill, muscle, heart or liver. Perchlorate sensitive (125)I uptake was found in stomach, lung, kidney, gill, and small intestine but not muscle, liver, or heart. Perchlorate-sensitive (125)I uptake by stomach was 6-10 times greater than in any other non-thyroidal tissue in tadpoles. While NF stage 49 tadpoles exhibited perchlorate-sensitive uptake in stomach it was roughly 4-fold less than that observed in NF stage 55 tadpoles. Although abundance of NIS gene transcripts was greater in stomachs from NF stage 55 compared to NF stage 49 tadpoles this difference was not statistically significant. We conclude that gastric iodide uptake increases between NF stages 49 and 55, possibly due to post-translational changes in NIS glycosylation or trafficking within gastric mucosal cells. These developmental changes in gastric NIS gene expression may affect iodide availability to the thyroid gland.

  4. Leaching of Au, Ag, and Pd from waste printed circuit boards of mobile phone by iodide lixiviant after supercritical water pre-treatment.

    Science.gov (United States)

    Xiu, Fu-Rong; Qi, Yingying; Zhang, Fu-Shen

    2015-07-01

    Precious metals are the most attractive resources in waste printed circuit boards (PCBs) of mobile phones. In this work, an alternative process for recovering Au, Ag, and Pd from waste PCBs of mobile phones by supercritical water oxidation (SCWO) pre-treatment combined with iodine-iodide leaching process was developed. In the process, the waste PCBs of mobile phones were pre-treated in supercritical water, then a diluted hydrochloric acid leaching (HL) process was used to recovery the Cu, whose leaching efficiency was approximately 100%, finally the resulting residue was subjected to the iodine-iodide leaching process for recovering the Au, Ag, and Pd. Experimental results indicated that SCWO pre-treatment temperature, time, and pressure had significant influence on the Au, Ag, and Pd leaching from (SCWO+HL)-treated waste PCBs. The optimal SCWO pre-treatment conditions were 420°C and 60min for Au and Pd, and 410°C and 30min for Ag. The optimum dissolution parameters for Au, Pd, and Ag in (SCWO+HL)-treated PCBs with iodine-iodide system were leaching time of 120min (90min for Ag), iodine/iodide mole ratio of 1:5 (1:6 for Ag), solid-to-liquid ratio (S/L) of 1:10g/mL (1:8g/mL for Ag), and pH of 9, respectively. It is believed that the process developed in this study is environment friendly for the recovery of Au, Ag, and Pd from waste PCBs of mobile phones by SCWO pre-treatment combined with iodine-iodide leaching process.

  5. Evaluation of potassium iodide (KI) and ammonium perchlorate (NH4ClO4) to ameliorate 131I- exposure in the rat.

    Science.gov (United States)

    Harris, C A; Fisher, J W; Rollor, E A; Ferguson, D C; Blount, B C; Valentin-Blasini, L; Taylor, M A; Dallas, C E

    2009-01-01

    Nuclear reactor accidents and the threat of nuclear terrorism have heightened the concern for adverse health risks associated with radiation poisoning. Potassium iodide (KI) is the only pharmaceutical intervention that is currently approved by the Food and Drug Administration for treating (131)I(-) exposure, a common radioactive fission product. Though effective, KI administration needs to occur prior to or as soon as possible (within a few hours) after radioactive exposure to maximize the radioprotective benefits of KI. During the Chernobyl nuclear reactor accident, KI was not administered soon enough after radiation poisoning occurred to thousands of people. The delay in administration of KI resulted in an increased incidence of childhood thyroid cancer. Perchlorate (ClO(4)(-)) was suggested as another pharmaceutical radioprotectant for 131I- poisoning because of its ability to block thyroidal uptake of iodide and discharge free iodide from the thyroid gland. The objective of this study was to compare the ability of KI and ammonium perchlorate to reduce thyroid gland exposure to radioactive iodide (131I-). Rats were dosed with 131I- tracer and 0.5 and 3 h later dosed orally with 30 mg/kg of either ammonium perchlorate or KI. Compared to controls, both anion treatments reduced thyroid gland exposure to 131I- equally, with a reduction ranging from 65 to 77%. Ammonium perchlorate was more effective than stable iodide for whole-body radioprotectant effectiveness. KI-treated animals excreted only 30% of the (131)I(-) in urine after 15 h, compared to 47% in ammonium perchlorate-treated rats. Taken together, data suggest that KI and ammonium perchlorate are both able to reduce thyroid gland exposure to 131I- up to 3 h after exposure to 131I-. Ammonium perchlorate may offer an advantage over KI because of its ability to clear 131I- from the body.

  6. Benchmark Gamma Spectroscopy Measurements of Uranium Hexafluoride in Aluminmum Pipe with a Sodium Iodide Detector

    Energy Technology Data Exchange (ETDEWEB)

    March-Leuba, Jose A [ORNL; Uckan, Taner [ORNL; Gunning, John E [ORNL; Brukiewa, Patrick D [ORNL; Upadhyaya, Belle R [ORNL; Revis, Stephen M [ORNL

    2010-01-01

    monitor (FM) and an enrichment monitor (EM). Development of the FM is primarily the responsibility of Oak Ridge National Laboratory, and development of the EM is primarily the responsibility of Los Alamos National Laboratory. The FM will measure {sup 235}U mass flow rate by combining information from measuring the UF{sub 6} volumetric flow rate and the {sup 235}U density. The UF{sub 6} flow rate will be measured using characteristics of the process pumps used in product and tail UF{sub 6} header process lines of many GCEPs, and the {sup 235}U density will be measured using commercially available sodium iodide (NaI) gamma ray scintillation detectors. This report describes the calibration of the portion of the FM that measures the {sup 235}U density. Research has been performed to define a methodology and collect data necessary to perform this calibration without the need for plant declarations. The {sup 235}U density detector is a commercially available system (GammaRad made by Amptek, www.amptek.com) that contains the NaI crystal, photomultiplier tube, signal conditioning electronics, and a multichannel analyzer (MCA). Measurements were made with the detector system installed near four {sup 235}U sources. Two of the sources were made of solid uranium, and the other two were in the form of UF{sub 6} gas in aluminum piping. One of the UF{sub 6} gas sources was located at ORNL and the other at LANL. The ORNL source consisted of two pipe sections (schedule 40 aluminum pipe of 4-inch and 8-inch outside diameter) with 5.36% {sup 235}U enrichment, and the LANL source was a 4-inch schedule 40 aluminum pipe with 3.3% {sup 235}U enrichment. The configurations of the detector on these test sources, as well as on long straight pipe configurations expected to exist at GCEPs, were modeled using the computer code MCNP. The results of the MCNP calculations were used to define geometric correction factors between the test source and the GCEP application. Using these geometric correction

  7. PENENTUAN KADAR IODIDA DAN IODAT DALAM GARAM BERIODIUM DENGAN METODE KROMATOGRAFI CAIR KENERJA TINGGI PASANGAN ION [Determination of Iodate and Iodide Content in Iodized Salt By Ion Pair High Performance Liquid Chromatography Method

    Directory of Open Access Journals (Sweden)

    Wisnu Cahyadi1

    2004-04-01

    Full Text Available Two species of iodine, i.e. iodide and iodate in commercial iodized salt were determined using ion pair HPLC. From 15 samples analysed, the iodide and iodate content ranged from 24,05 ± 2,51 to 70,25 ± 3,78 ppm and from 31,43 ± 8,10 to 87,59 ± 0,44 ppm, respectively. The method used was found satisfactory in terms of precission, accuracy, sensitivity and selectivity, therefore the method seem acceptable for the determination of iodide and iodate content in iodized salt samples.

  8. Leaching of Au, Ag, and Pd from waste printed circuit boards of mobile phone by iodide lixiviant after supercritical water pre-treatment

    Energy Technology Data Exchange (ETDEWEB)

    Xiu, Fu-Rong, E-mail: xiu_chem@hotmail.com [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350108 (China); Qi, Yingying [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350108 (China); Zhang, Fu-Shen [Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China)

    2015-07-15

    Highlights: • We report a novel process for recovering Au, Ag, and Pd from waste PCBs. • The effect of SCWO on the leaching of Au, Ag, and Pd in waste PCBs was studied. • SCWO was highly efficient for enhancing the leaching of Au, Ag, and Pd. • The optimum leaching parameters for Au, Ag, and Pd in iodine–iodide were studied. - Abstract: Precious metals are the most attractive resources in waste printed circuit boards (PCBs) of mobile phones. In this work, an alternative process for recovering Au, Ag, and Pd from waste PCBs of mobile phones by supercritical water oxidation (SCWO) pre-treatment combined with iodine–iodide leaching process was developed. In the process, the waste PCBs of mobile phones were pre-treated in supercritical water, then a diluted hydrochloric acid leaching (HL) process was used to recovery the Cu, whose leaching efficiency was approximately 100%, finally the resulting residue was subjected to the iodine–iodide leaching process for recovering the Au, Ag, and Pd. Experimental results indicated that SCWO pre-treatment temperature, time, and pressure had significant influence on the Au, Ag, and Pd leaching from (SCWO + HL)-treated waste PCBs. The optimal SCWO pre-treatment conditions were 420 °C and 60 min for Au and Pd, and 410 °C and 30 min for Ag. The optimum dissolution parameters for Au, Pd, and Ag in (SCWO + HL)-treated PCBs with iodine–iodide system were leaching time of 120 min (90 min for Ag), iodine/iodide mole ratio of 1:5 (1:6 for Ag), solid-to-liquid ratio (S/L) of 1:10 g/mL (1:8 g/mL for Ag), and pH of 9, respectively. It is believed that the process developed in this study is environment friendly for the recovery of Au, Ag, and Pd from waste PCBs of mobile phones by SCWO pre-treatment combined with iodine–iodide leaching process.

  9. Synthesis of two potential NK1-receptor ligands using [1-11C]ethyl iodide and [1-11C]propyl iodide and initial PET-imaging

    Directory of Open Access Journals (Sweden)

    Genchel Tove

    2007-07-01

    Full Text Available Abstract Background The previously validated NK1-receptor ligand [O-methyl-11C]GR205171 binds with a high affinity to the NK1-receptor and displays a slow dissociation from the receptor. Hence, it cannot be used in vivo for detecting concentration changes in substance P, the endogenous ligand for the NK1-receptor. A radioligand used for monitoring these changes has to enable displacement by the endogenous ligand and thus bind reversibly to the receptor. Small changes in the structure of a receptor ligand can lead to changes in binding characteristics and also in the ability to penetrate the blood-brain barrier. The aim of this study was to use carbon-11 labelled ethyl and propyl iodide with high specific radioactivity in the synthesis of two new and potentially reversible NK1-receptor ligands with chemical structures based on [O-methyl-11C]GR205171. Methods [1-11C]Ethyl and [1-11C]propyl iodide with specific radioactivities of 90 GBq/μmol and 270 GBq/μmol, respectively, were used in the synthesis of [O-methyl-11C]GR205171 analogues by alkylation of O-desmethyl GR205171. The brain uptake of the obtained (2S,3S-N-(1-(2- [1-11C]ethoxy-5-(3-(trifluoromethyl-4H-1,2,4-triazol-4-ylphenylethyl-2-phenylpiperidin-3-amine (I and (2S,3S-2-phenyl-N-(1-(2- [1-11C]propoxy-5-(3-(trifluoromethyl-4H-1,2,4-triazol-4-ylphenylethylpiperidin-3-amine (II was studied with PET in guinea pigs and rhesus monkeys and compared to the uptake of [O-methyl-11C]GR205171. Results All ligands had similar uptake distribution in the guinea pig brain. The PET-studies in rhesus monkeys showed that (II had no specific binding in striatum. Ligand (I had moderate specific binding compared to the [O-methyl-11C]GR205171. The ethyl analogue (I displayed reversible binding characteristics contrary to the slow dissociation rate shown by [O-methyl-11C]GR205171. Conclusion The propyl-analogue (II cannot be used for detecting changes in NK1-ligand levels, while further studies should be

  10. Chemical conversion of cisplatin and carboplatin with histidine in a model protein crystallized under sodium iodide conditions

    Energy Technology Data Exchange (ETDEWEB)

    Tanley, Simon W. M.; Helliwell, John R., E-mail: john.helliwell@manchester.ac.uk [University of Manchester, Brunswick Street, Manchester M13 9PL (United Kingdom)

    2014-08-29

    Crystals of HEWL with cisplatin and HEWL with carboplatin grown in sodium iodide conditions both show a partial chemical transformation of cisplatin or carboplatin to a transiodoplatin (PtI{sub 2}X{sub 2}) form. The binding is only at the N{sup δ} atom of His15. A further Pt species (PtI{sub 3}X) is also seen, in both cases bound in a crevice between symmetry-related protein molecules. Cisplatin and carboplatin are platinum anticancer agents that are used to treat a variety of cancers. Previous X-ray crystallographic studies of carboplatin binding to histidine in hen egg-white lysozyme (HEWL) showed a partial chemical conversion of carboplatin to cisplatin owing to the high sodium chloride concentration used in the crystallization conditions. Also, the co-crystallization of HEWL with carboplatin in sodium bromide conditions resulted in the partial conversion of carboplatin to the transbromoplatin form, with a portion of the cyclobutanedicarboxylate (CBDC) moiety still present. The results of the co-crystallization of HEWL with cisplatin or carboplatin in sodium iodide conditions are now reported in order to determine whether the cisplatin and carboplatin converted to the iodo form, and whether this took place in a similar way to the partial conversion of carboplatin to cisplatin in NaCl conditions or to transbromoplatin in NaBr conditions as seen previously. It is reported here that a partial chemical transformation has taken place to a transplatin form for both ligands. The NaI-grown crystals belonged to the monoclinic space group P2{sub 1} with two molecules in the asymmetric unit. The chemically transformed cisplatin and carboplatin bind to both His15 residues, i.e. in each asymmetric unit. The binding is only at the N{sup δ} atom of His15. A third platinum species is also seen in both conditions bound in a crevice between symmetry-related molecules. Here, the platinum is bound to three I atoms identified based on their anomalous difference electron densities

  11. Synthesis and Crystal Structure of a Novel 1D Mercury(II) Iodide Coordination Polymer Containing 40-Membered Macrocycle%Synthesis and Crystal Structure of a Novel 1D Mercury(II) Iodide Coordination Polymer Containing 40-Membered Macrocycle

    Institute of Scientific and Technical Information of China (English)

    GAN Xiao-Ping; KONG Ling; WU Peng; LV Chen; TU Yu-Long; CHEN Yi-Xin; ZHOU Hong-Ping; WU Jie-Ying; TIAN Yu-Peng

    2011-01-01

    A mercury coordination polymer [Hg3(TizT)216]n (Mr = 1921.72, TizT = 2,4,6- tri(imidazole- 1-yl)- 1,3,5-triazine) containing a 40-membered macrocycle which was constructed by four TizT ligands and four mercury(II) iodide molecules had been synthesized by the reaction of HgI2 with TizT. The complex was characterized by elemental analysis, FT-IR, ^1H NMR spectra and X-ray crystallography. The crystal of the complex belongs to the monoclinic system and C2/c space group with a = 35.840(5), b = 8.169(5), c = 14.980(5) A, β = 104.466(5)°, Z= 4, V= 4247(3) A^3, De = 3.006 g·cm^-3, μ= 15.223 mm^-1, F(000) = 3384, Rint = 0.0504, wR = 0.0833 and constructs a chair-like conformation of cyclohexane one by one, which forms a 1-D polymer through the fashion of fused ring aromatic hydrocarbon. The hydrogen bonds and π-π interactions shape the 2-D network structure. The two compounds excited weak fluorescence.

  12. Energy Transfer between Fluorescein Isothiocyanate and Propidium Iodide – A Problem in the Estimation of Tpot with the Bromodeoxyuridine–DNA Flow Cytometry Technique?

    Directory of Open Access Journals (Sweden)

    Maria C. Johansson

    1999-01-01

    Full Text Available Energy transfer in flow cytometry can occur when two fluorochromes are bound in close proximity (generally within 100 Å and the emission spectrum of one fluorochrome overlaps significantly with the excitation spectrum of the other. The latter criterium is fullfilled for the fluorochromes fluorescein isothiocyanate and propidium iodide and also the former when they, e.g., are used in bromodeoxyuridine – DNA flow cytometry methods. In the present growth kinetic study using this method, we show that energy transfer does take place between fluorescein isothiocyanate and propidium iodide which results in a detected increase in DNA content with 2–3%. Despite the erroneous increase in the obtained DNA content values, this does not seem to have any influence on the calculation of DNA synthesis time and potential doubling time where the DNA content, based on the relative movement principle of the labelled cells, is used.

  13. Stereospecific Synthesis of (Z)-α-Fluoro-β-trifluoromethyl Vinyl Iodides and Their Application to the Synthesis of Polyfluorinated Thienyl Alkadienes

    Institute of Scientific and Technical Information of China (English)

    SHEN,Yan-Chang; WANG,Guo-Ping

    2006-01-01

    The direct iodination of polyfluorinated vinyl stannanes by tin-iodine exchange methodology was achieved giving (Z)-α-fluoro-β-trifluoromethyl vinyl iodides stereospecifically. Changing the substituent in R group from the electron-withdrawing group to electron-donating group led to an increase in the yield from 78% to 90%, while it was moved from para to meta position the reaction did not afford a dramatic change in the yield (90% to 95%). In addition, this reaction also can be applied to the vinyl stannane with heterocyclic group. The further coupling reaction of prepared vinyl iodide containing heterocyclic moiety with (Z)-α-fluoro-β-trifluoromethylstannanes gave polyfluorinated heterocyclic alkadienes with 2E,4E-selectivity.

  14. Synthesis, spectral characterization and in vitro antibacterial evaluation and Petra/Osiris/Molinspiration analyses of new Palladium(II iodide complexes with thioamides

    Directory of Open Access Journals (Sweden)

    Shafqat Nadeem

    2016-09-01

    Full Text Available The paper emphasizes on the synthesis of Palladium(II iodide complexes containing based ligands. The new compounds of general formulae [Pd(L4]I2 where L = Thiourea (Tu, Methylthiourea (Metu, Dimethylthiourea (Dmtu, Tetramethylthiourea (Tmtu, Imidazolidine-2-thione (Imt, Mercaptopyridine (Mpy, Mercaptopyrimidine (Mpm, and Thionicotinamide (Tna were prepared simply by reacting K2[PdCl4] with the corresponding thioamides in 1:2 M ratio and then with 2 equivalents Potassium iodide. The complexes were characterized by elemental analysis and spectroscopic techniques (IR, 1H and13C NMR. All the synthesized complexes were screened for antibacterial activity and some of compounds have shown good activities against both gram positive and gram negative bacteria. POM analyses reveal that the compounds are only slightly toxic and present a potential for antibacterial activity. Moreover, they have 16–23% drug score which is an important parameter for the compound possessing the drug properties.

  15. Remarkable rate acceleration of SmI3-mediated iodination of acetates of Baylis-Hillman adducts in ionic liquid: facile synthesis of (Z)-allyl iodides

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Stereoselective transformation of Baylis-Hillman acetates 1 into corresponding (Z)-allyl iodides 2 has been achieved by treatment of 1 with samarium triiodide in THF. Remarkable rate acceleration of samarium triiodide-mediated iodination of 1 was found when ionic liquid 1-n-butyl-3-methyl-imidazolium tetrafluroborate ([bmim]BF4) was used as reaction media in stead of THF. This novel approach proceeds readily at 50 ℃ within a few minutes to afford (Z)-allyl iodides 2 in excellent yields. A mechanism involving stereoselective iodination of the acetates of Baylis-Hillman adducts by samarium triiodide is described, in which a six-membered ring transition state played a key role in the stereoselective formation of 2.

  16. A novel sodium iodide and ammonium molybdate co-catalytic system for the efficient synthesis of 2-benzimidazoles using hydrogen peroxide under ultrasound irradiation.

    Science.gov (United States)

    Bai, Guo-Yi; Lan, Xing-Wang; Chen, Guo-Feng; Liu, Xiao-Fang; Li, Tian-Yu; Shi, Ling-Juan

    2014-03-01

    The reaction of aldehydes and o-phenylenediamine for the preparation of 2-benzimidazoles has been studied using hydrogen peroxide as an oxidant under ultrasound irradiation at room temperature in this paper. The combination of substoichiometric sodium iodide and ammonium molybdate as co-catalysts, together with using small amounts of hydrogen peroxide, makes this transformation very efficient and attractive under ultrasound. Thus, a mild, green and efficient method is established to carry out this reaction in high yield.

  17. Potassium iodide catalyzed reductive dehalogenation of α-halo-ketones using Hantzsch ester diethyl 1,4-dihydro-2,6-dimethylpyridine-3,5-dicarboxylate as reductant

    Institute of Scientific and Technical Information of China (English)

    Hong Sheng Li; Yi Qun Li

    2010-01-01

    In the presence of diethyl 1,4-dihydro-2,6-dimethylpyridine-3,5-dicarboxylate (DHP) and a catalytic amount of potassium iodide,several α-halo ketones were easily reduced to the corresponding ketones in acetone media.The procedure presented here showed several merits such as short reaction time,practical experimental and isolated procedure,and excellent yields of products.

  18. Effect of iodide on Fas, Fas-ligand and Bcl-w mRNA expression in thyroid of NOD mice pretreated with methimazole

    Directory of Open Access Journals (Sweden)

    L.H.B. Boechat

    2002-03-01

    Full Text Available Nonobese diabetic (NOD mice and a derived strain, NOD.H.2h4, have been used as a model for experimental spontaneous thyroiditis and thyroiditis induced by iodide excess after a goiter-inducing period. Some authors have proposed that iodide, given after methimazole or propylthiouracil, is capable of inducing apoptosis in thyroid cells and that anti-thyroid drugs can modulate the expression of apoptosis components such as Fas and its ligand (Fas-L. Here we evaluated the effect of potassium iodide (20 µg/animal for 4 days, ip given to NOD mice at the 10th week of life after exposure to methimazole (1 mg/ml in drinking water from the 4th to the 10th week of life. Fas, Fas-L and Bcl-w expression were analyzed semiquantitatively by RT-PCR immediately after potassium iodide administration (group MI44D or at week 32 (MI32S. Control groups were added at 10 (C10 and 32 weeks (C32, as well as a group that received only methimazole (CM10. An increase in the expression of Fas-L and Bcl-w (P<0.01, ANOVA was observed in animals of group MI44D, while Fas was expressed at higher levels (P = 0.02 in group C32 (72.89 ± 47.09 arbitrary units when compared to group C10 (10.8 ± 8.55 arbitrary units. Thus, the analysis of Fas-L and Bcl-w expression in the MI44D group and Fas in group C32 allowed us to detect two different patterns of expression of these apoptosis components in thyroid tissue of NOD mice.

  19. Effects of high concentrations of iodide exposure on mitochondrial superoxide production in the thyroid of metallothionein Ⅰ/Ⅱ knockout mice

    Institute of Scientific and Technical Information of China (English)

    张娜

    2014-01-01

    Objective To investigate the effects of high concentrations of iodide exposure on mitochondrial superoxide production,cell viability and cell damage in the thyroid of metallothioneinⅠ/Ⅱknockout(MT-Ⅰ/ⅡKO)mice and corresponding wild type(WT)mice.Methods Thyroid cell suspension of six to eight weeks old healthy male MT-Ⅰ/ⅡKO mice and WT mice were prepared.The

  20. Reduction of ketones and alkyl iodides by SmI(2) and Sm(II)-HMPA complexes. Rate and mechanistic studies.

    Science.gov (United States)

    Prasad, E; Flowers, Robert A

    2002-06-19

    The effect of HMPA on the electron transfer (ET) rate of samarium diiodide reduction reactions in THF was analyzed for a series of ketones (2-butanone, methyl acetoacetate, and N,N-dimethylacetoacetamide) and alkyl iodides (1-iodobutane and 2-iodobutane) with stopped flow spectrophotometric studies. Activation parameters for the ET processes were determined by temperature-dependence studies over a range of 30-50 degrees C. The ET rate constants and the activation parameters obtained for the above systems in the presence of different equivalents of HMPA were compared to understand the mechanism of action of HMPA on various substrates. The results obtained from these studies indicate that coordination or chelation is possible in the transition state geometry for SmI(2)/ketone systems even in the presence of the sterically demanding ligand HMPA. After the addition of 4 equiv of HMPA the ET rate and activation parameters for ketone reduction by Sm is unaffected by further HMPA addition while a linear dependence of ET rate on the equivalents of HMPA was found in the SmI(2)/alkyl iodide system. The results of these studies are consistent with an inner-sphere-type ET for the reduction of ketones by SmI(2) (and SmI(2)[bond]HMPA complexes) and an outer-sphere-type ET for the reduction of alkyl iodides by SmI(2) or SmI(2)[bond]HMPA complexes.

  1. The Effect of Lithium Iodide to the Properties of Carboxymethyl κ-Carrageenan/Carboxymethyl Cellulose Polymer Electrolyte and Dye-Sensitized Solar Cell Performance

    Directory of Open Access Journals (Sweden)

    Siti Rudhziah Che Balian

    2016-05-01

    Full Text Available This study was undertaken to investigate the solid biopolymer electrolytes based on a carboxymethyl κ-carrageenan/carboxymethyl cellulose blend complexed with lithium iodide of various weight ratios. The complexation of the doping salt with the polymer blend was confirmed by Fourier transform infrared spectroscopy. Ionic conductivity of the film was determined by impedance spectroscopy in the frequency range of 10 Hz to 4 MHz and in the temperature range of 303–338 K. The ionic conductivity increased with the increase in lithium iodide concentration as well as temperature. The membrane comprising 30 wt % of lithium iodide was found to give the highest conductivity of 3.89 × 10−3 S·cm−1 at room temperature. The increase in conductivity was associated with the increase in the number as well as the mobility of the charge carries. The conductivity increase with temperature followed the Vogel–Tamman–Fulcher model. The fabricated dye-sensitive solar cell, FTO/TiO2-dye/CMKC/CMCE-LiI (30 wt % +I2/Pt exhibited the highest conversion efficiency of 0.11% at a light intensity of 100 mW·cm−2. This indicated that the biopolymer blend electrolyte system has potential for use in dye-sensitized solar cells.

  2. Highly efficient solid-state dye-sensitized solar cells based on hexylimidazolium iodide ionic polymer electrolyte prepared by in situ low-temperature polymerization

    Science.gov (United States)

    Wang, Guiqiang; Yan, Chao; Zhang, Juan; Hou, Shuo; Zhang, Wei

    2017-03-01

    Solid-state dye-sensitized solar cells (DSCs) are fabricated using a novel ionic polymer electrolyte containing hexylimidazolium iodide (HII) ionic polymer prepared by in situ polymerization of N,N‧-bis(imidazolyl) hexane and 1,6-diiodohexane without an initiator at low temperature (40 °C). The as-prepared HII ionic polymer has a similar structure to alkylimidazolium iodide ionic liquid, and the imidazolium cations are contained in the polymer main chain; so, it can act simultaneously as the redox mediator in the electrolyte. By incorporating an appropriate amount of 1,3-dimethylimidazolium iodide (DMII) in HII ionic polymer (DMII/HII ionic polymer = 0.7:1, weight ratio), the conductivity of the ionic polymer electrolyte is greatly improved due to the formation of Grotthuss bond exchange. In addition, in situ synthesis of ionic polymer electrolyte guarantees a good pore-filling of the electrolyte in the TiO2 photoanode. As a result, the solid-state DSC based on the ionic polymer electrolyte containing HII ionic polymer and DMII without iodine achieves a conversion efficiency of 6.55% under the illumination of 100 mW cm-2 (AM 1.5), which also exhibits a good at-rest stability at room temperature.

  3. Influence of organic additive to PVDF-HFP mixed iodide electrolytes on the photovoltaic performance of dye-sensitized solar cells

    Science.gov (United States)

    Senthil, R. A.; Theerthagiri, J.; Madhavan, J.; Ganesan, S.; Arof, A. K.

    2017-02-01

    The influence of 5-amino-1,3,4-thiadiazole-2-thiol (ATDT) on the ionic conductivity of poly(vinylidinefluoride-co-hexafluoropropylene) (PVDF-HFP) polymer electrolytes with mixed iodide salts (potassium iodide (KI) and tetrabutylammonium iodide (TBAI)) and iodine (I2) were studied for dye-sensitized solar cells (DSSCs). The pure and different weight percentage (wt%) ratios (2%, 3%, 4%, 5% and 6%) of ATDT modified PVDF-HFP/KI+TBAI/I2 electrolyte films were prepared by solution casting technique using DMF as a solvent. The polymer electrolyte films were characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffractometer (XRD), electrochemical impedance spectroscopy and scanning electron microscopy (SEM). The pure PVDF-HFP/TBAI+KI/I2 electrolyte exhibited the ionic conductivity value of 9.99×10-6 S cm-1 at room temperature, which was found to be improved to a maximum value of 2.82×10-4 S cm-1 at 4 wt% of ATDT modified polymer electrolyte. The photovoltaic characterization studies showed higher power conversion efficiency of 4.64% for DSSC assembled with the optimized wt% of ATDT modified polymer electrolyte than the pure PVDF-HFP/KI+TBAI/I2 electrolyte (1.88%) at an illumination intensity of 60 mW/cm2. Hence, the studies concluded that the ATDT modified polymer electrolyte can be a suitable material for DSSC applications.

  4. 复方碘化钾滴眼液无菌检查方法的验证%Validation of sterility test of compound potassium iodide eye drops

    Institute of Scientific and Technical Information of China (English)

    余晓霞; 邱凯锋; 廖庆权

    2014-01-01

    目的:建立复方碘化钾滴眼液无菌检查方法。方法按《中国药典》2010年版二部无菌检查法中薄膜过滤法对复方碘化钾滴眼液的无菌检查方法进行验证。结果该制剂的无菌检查选用薄膜过滤法,以金黄色葡萄球菌为阳性对照菌,冲洗总量100 ml。结论经方法学验证,该法可行,结果可靠。%ObjectiveTo establish the method of sterility test of compound potassium iodide eye drops. MethodsAccording to sterility test in the appendix ofChinese Pharmacopoeia 2010 (section 2), the membrane filteration used in the sterility test of compound potassium iodide eye drops was validated.ResultsThe membrane filteration was used in the sterility test of compound potassium iodide eye drops, and staphylococcus aureus was used as positive control germs and the total amount of irrigation fluid was 100 ml.Conclusion Through the technological validation, the method is applicable and the result is reliable.

  5. Effect of triclosan, triclocarban, 2,2',4,4'-tetrabromodiphenyl ether, and bisphenol A on the iodide uptake, thyroid peroxidase activity, and expression of genes involved in thyroid hormone synthesis.

    Science.gov (United States)

    Wu, Yuanfeng; Beland, Frederick A; Fang, Jia-Long

    2016-04-01

    Triclosan, triclocarban, 2,2',4,4'-tetrabromodiphenyl ether (BDE-47), and bisphenol A (BPA) have been reported to disturb thyroid hormone (TH) homeostasis. We have examined the effects of these chemicals on sodium/iodide symporter (NIS)-mediated iodide uptake and the expression of genes involved in TH synthesis in rat thyroid follicular FRTL-5 cells, and on the activity of thyroid peroxidase (TPO) using rat thyroid microsomes. All four chemicals inhibited NIS-mediated iodide uptake in a concentration-dependent manner. A decrease in the iodide uptake was also observed in the absence of sodium iodide. Kinetic studies showed that all four chemicals were non-competitive inhibitors of NIS, with the order of Ki values being triclosantriclosan or triclocarban. BDE-47 decreased the level of Tpo, while BPA altered the expression of all six genes. Triclosan and triclocarban inhibited the activity of TPO at 166 and >300 μM, respectively. Neither BDE-47 nor BPA affected TPO activity. In conclusion, triclosan, triclocarban, BDE-47, and BPA inhibited iodide uptake, but had differential effects on the expression of TH synthesis-related genes and the activity of TPO.

  6. Preparation of Copper Iodide (CuI) Thin Film by In-Situ Spraying and Its Properties

    Science.gov (United States)

    Rahmi, G. H.; Pratiwi, P.; Nuryadi, B. W.; Aimon, A. H.; Winata, T.; Iskandar, F.

    2016-08-01

    Perovskite based solar cells have attracted interest as low-cost and high-efficiency solar cells due to their great performance, with efficiency up to 20.1%. One type of hole transport material (HTM) used in perovskite based solar cells is copper iodide (CuI) thin film. CuI is inexpensive and has high mobility compared to other HTMs commonly used in perovskite based solar cells. However, diisopropylsulfide solvent, which is used to dissolve CuI in the preparation process, is a malodorous and toxic compound. Therefore, the objective of this research was to develop a synthesis method for CuI thin film with in-situ spraying, a low- cost, safe and easy fabrication method. As precursor solution, CuSO45H2O was dissolved in ammonia and KI aqueous solution. The precursor solution was then sprayed directly onto a glass substrate with appropriate temperature to form CuI film. The prepared thin films were characterized by X-ray diffractometer, UV-Vis spectrophotometer, scanning electron microscope and four-point probes to study their properties.

  7. Decoration of cesium iodide nano particles on patterned carbon nanotube emitter arrays to improve their field emission

    Energy Technology Data Exchange (ETDEWEB)

    Shahi, Monika, E-mail: moni.binda@gmail.com; Gautam, S.; Shah, P. V.; Rawat, J. S.; Chaudhury, P. K. [Solid State Physics Laboratory (India); Harsh [Jamia Millia Islamia, Department of Physics (India); Tandon, R. P. [University of Delhi, Department of Physics and Astrophysics (India)

    2013-03-15

    Arrays of aligned carbon nanotube (CNT) bundles were synthesized on the pre-patterned silicon substrate using thermal chemical vapor deposition. Silicon substrate was patterned with square arrays of 10 Multiplication-Sign 10 {mu}m iron catalyst using photolithography, iron sputtering, and a lift-off process. After field emission (FE) measurement in diode configuration, CNT emitter arrays (CEAs) were decorated with cesium iodide (CsI) nano particles (NPs) using thermal evaporation with substrate heating at 300 Degree-Sign C. FE of pristine CEAs and CsI NPs decorated CEAs were carried out under same vacuum condition and constant inter-electrode separation. Pristine CEAs and CsI NPs decorated CEAs were characterized using scanning electron microscope, transmission electron microscope, energy-dispersive X-ray spectroscopy, X-ray diffraction, and Raman characterization. From FE comparison plots, it was observed that CsI NPs decoration on the CEAs had significantly lowered the turn-on electric field from 3.00 to 2.13 V/{mu}m. A remarkable improvement of more than 50 % in the current density, from 11.02 to 17.33 mA/cm{sup 2}, was also observed at a constant applied electric field of 5 V/{mu}m.

  8. Decoration of cesium iodide nano particles on patterned carbon nanotube emitter arrays to improve their field emission

    Science.gov (United States)

    Shahi, Monika; Gautam, S.; Shah, P. V.; Rawat, J. S.; Chaudhury, P. K.; Harsh; Tandon, R. P.

    2013-03-01

    Arrays of aligned carbon nanotube (CNT) bundles were synthesized on the pre-patterned silicon substrate using thermal chemical vapor deposition. Silicon substrate was patterned with square arrays of 10 × 10 μm iron catalyst using photolithography, iron sputtering, and a lift-off process. After field emission (FE) measurement in diode configuration, CNT emitter arrays (CEAs) were decorated with cesium iodide (CsI) nano particles (NPs) using thermal evaporation with substrate heating at 300 °C. FE of pristine CEAs and CsI NPs decorated CEAs were carried out under same vacuum condition and constant inter-electrode separation. Pristine CEAs and CsI NPs decorated CEAs were characterized using scanning electron microscope, transmission electron microscope, energy-dispersive X-ray spectroscopy, X-ray diffraction, and Raman characterization. From FE comparison plots, it was observed that CsI NPs decoration on the CEAs had significantly lowered the turn-on electric field from 3.00 to 2.13 V/μm. A remarkable improvement of more than 50 % in the current density, from 11.02 to 17.33 mA/cm2, was also observed at a constant applied electric field of 5 V/μm.

  9. Crystalline texture and mammography energy range detection studies of pyrolysed lead iodide films: Effects of solution concentration

    Energy Technology Data Exchange (ETDEWEB)

    Condeles, J.F., E-mail: condeles@fisica.uftm.edu.br [Department of Physics, Institute of Exact Sciences, Naturals and Education, Federal Universty of Triângulo Mineiro, 38064-200, Uberaba, MG (Brazil); Mulato, M. [Department of Physics, Faculty of Philosophy, Sciences and Letters at Ribeirão Preto, University of São Paulo, Av. Bandeirantes 3900, 14040-901, Ribeirão Preto, SP (Brazil)

    2015-09-15

    Semiconductor lead iodide (PbI{sub 2}) films have been extensively studied due to their potential applications in room temperature ionizing radiation detectors. The influence of PbI{sub 2} solution concentration on the final properties of the films grown by spray pyrolysis was investigated. The solution concentration was varied in the range of 10 g/l up to 50 g/l. Total deposition time of 2.5 h was used and average growth rate varying from 22 Å s{sup −1} up to 62 Å s{sup −1} was obtained as a function of solution concentration. X-ray diffraction was used to investigate the structural properties of the films. Variations in microstructure as a function of solution concentration were studied using crystal texture calculations. The smallest value of electrical resistivity was obtained for the largest solution concentration. Mammographic X-ray irradiation from 10 mR up to 1450 mR was carried out with equivalent photon energy at 14 keV and the sensor results are discussed. - Highlights: • PbI{sub 2} films were grown by spray pyrolysis deposition method. • Variations in microstructure were studied using crystal texture calculations. • The films were tested in the mammography X-ray energy range. • The response is very linear with a slope of 13 μA/cm{sup 2} R.

  10. Red mercuric iodide crystals obtained by isothermal solution evaporation: Characterization for mammographic X-ray imaging detectors

    Energy Technology Data Exchange (ETDEWEB)

    Caldeira, A.M.F.; Ugucioni, J.C.; Mulato, M.

    2014-02-11

    Millimeter-sized mercury iodide crystals were obtained by the isothermal evaporation technique using dimethylformamide (DMF), diethyl-ether/DMF mixture and THF. Different concentrations (18 mM and 400 mM) and solution temperature (25–80 °C) were used to obtain varied evaporation rates (0.1×10{sup −4}–5000×10{sup −4} ml/h). Different crystal sizes and shapes were obtained by changing solvents, mixture and initial solution volume. According to X-ray diffraction the samples are monocrystalline. The top surface was investigated by SEM. Optical band-gaps above 2 eV were obtained from photoacoustic spectroscopy. Photoluminescence spectra indicated band-to-band electronic transitions, and the presence of sub-band gap states. Excitons, structural defects and the presence of impurities are discussed and correlated to the electrical measurements. Crystals obtained using pure DMF as solvent showed better general properties, including under the exposure to mammographic X-ray energy range that led to sensibility of about 25 μC/Rcm{sup 2}.

  11. Water to atmosphere fluxes of {sup 131}I in relation with alkyl-iodide compounds from the Seine Estuary (France)

    Energy Technology Data Exchange (ETDEWEB)

    Connan, Olivier [Laboratoire de Radioecologie de Cherbourg-Octeville, Institut de Radioprotection et de Surete nucleaire (IRSN), Service d' Etudes et du Comportement des Radionucleides dans l' Environnement (SECRE), rue Max Pol Fouchet, 50130 Cherbourg-Octeville (France)], E-mail: olivier.connan@irsn.fr; Tessier, Emmanuel [Laboratoire de Chimie Analytique et Bio-Inorganique et Environnement, UMR CNRS universite de Pau et des Pays de l' Adour, Helioparc Pau Pyrenees, 2 Avenue Pierre Angot, 64053 Pau Cedex 9 (France); Maro, Denis [Laboratoire de Radioecologie de Cherbourg-Octeville, Institut de Radioprotection et de Surete nucleaire (IRSN), Service d' Etudes et du Comportement des Radionucleides dans l' Environnement (SECRE), rue Max Pol Fouchet, 50130 Cherbourg-Octeville (France); Amouroux, David [Laboratoire de Chimie Analytique et Bio-Inorganique et Environnement, UMR CNRS universite de Pau et des Pays de l' Adour, Helioparc Pau Pyrenees, 2 Avenue Pierre Angot, 64053 Pau Cedex 9 (France); Hebert, Didier; Rozet, Marianne; Voiseux, Claire; Solier, Luc [Laboratoire de Radioecologie de Cherbourg-Octeville, Institut de Radioprotection et de Surete nucleaire (IRSN), Service d' Etudes et du Comportement des Radionucleides dans l' Environnement (SECRE), rue Max Pol Fouchet, 50130 Cherbourg-Octeville (France)

    2008-07-15

    This study presents an original work on measurements of stable and radioactive iodinated species in the Seine estuary (France), with estimates fluxes of volatile gaseous species from water to the atmosphere. Various iodinated compounds were identified in water and air in particular {sup 131}I in water, what is unusual. Concentrations and behaviour of iodinated elements in the Seine estuary seem similar to what has been observed in other European estuaries. MeI (Methyl Iodide) and Total Volatile Iodine (TVI) fluxes from water to air vary between 392 and 13949 pmol m{sup -2} d{sup -1} and between 1279 and 16484 pmol m{sup -2} d{sup -1}, respectively. Water to air flux of TVI for the Seine river was estimated in the range 4-46 kg y{sup -1}. Measurements of {sup 131}I in water varying between 0.4 and 11.9 Bq m{sup -3}. Fluxes of {sup 131}I from water to atmosphere are in the range 2.4 x 10{sup 5}-1.3 x 10{sup 7} Bq y{sup -1}, close to an annual discharge of {sup 131}I by a nuclear reactor.

  12. Rapid and prodium iodide-compatible optical clearing method for brain tissue based on sugar/sugar-alcohol

    Science.gov (United States)

    Yu, Tingting; Qi, Yisong; Wang, Jianru; Feng, Wei; Xu, Jianyi; Zhu, Jingtan; Yao, Yingtao; Gong, Hui; Luo, Qingming; Zhu, Dan

    2016-08-01

    The developed optical clearing methods show great potential for imaging of large-volume tissues, but these methods present some nonnegligible limitations such as complexity of implementation and long incubation times. In this study, we tried to screen out rapid optical clearing agents by means of molecular dynamical simulation and experimental demonstration. According to the optical clearing potential of sugar and sugar-alcohol, we further evaluated the improvement in the optical clearing efficacy of mouse brain samples, imaging depth, fluorescence preservation, and linear deformation. The results showed that drops of sorbitol, sucrose, and fructose could quickly make the mouse brain sample transparent within 1 to 2 min, and induce about threefold enhancement in imaging depth. The former two could evidently enhance the fluorescence intensity of green fluorescent protein (GFP) and prodium iodide (PI) nuclear dye. Fructose could significantly increase the fluorescence intensity of PI, but slightly decrease the fluorescence intensity of GFP. Even though the three agents caused some shrinkage in samples, the contraction in horizontal and longitudinal directions are almost the same.

  13. Iodide transporter NIS regulates cancer cell motility and invasiveness by interacting with the Rho guanine nucleotide exchange factor LARG.

    Science.gov (United States)

    Lacoste, Claire; Hervé, Julie; Bou Nader, Myriam; Dos Santos, Alexandre; Moniaux, Nicolas; Valogne, Yannick; Montjean, Rodrick; Dorseuil, Olivier; Samuel, Didier; Cassio, Doris; Portulano, Carla; Carrasco, Nancy; Bréchot, Christian; Faivre, Jamila

    2012-11-01

    A number of solute carrier (SLC) proteins are subject to changes in expression and activity during carcinogenesis. Whether these changes play a role in carcinogenesis is unclear, except for some nutrients and ion carriers whose deregulation ensures the necessary reprogramming of energy metabolism in cancer cells. In this study, we investigated the functional role in tumor progression of the sodium/iodide symporter (NIS; aka SLC5A5), which is upregulated and mislocalized in many human carcinomas. Notably, we found that NIS enhanced cell migration and invasion without ion transport being involved. These functions were mediated by NIS binding to leukemia-associated RhoA guanine exchange factor, a Rho guanine exchange factor that activates the small GTPase RhoA. Sequestering NIS in intracellular organelles or impairing its targeting to the cell surface (as observed in many cancers) led to a further increase in cell motility and invasiveness. In sum, our results established NIS as a carrier protein that interacts with a major cell signaling hub to facilitate tumor cell locomotion and invasion.

  14. Crystallization of a perovskite film for higher performance solar cells by controlling water concentration in methyl ammonium iodide precursor solution.

    Science.gov (United States)

    Adhikari, Nirmal; Dubey, Ashish; Gaml, Eman A; Vaagensmith, Bjorn; Reza, Khan Mamun; Mabrouk, Sally Adel Abdelsalam; Gu, Shaopeng; Zai, Jiantao; Qian, Xuefeng; Qiao, Qiquan

    2016-02-07

    An optimal small amount of water added into methyl ammonium iodide (MAI) solution in isopropyl alcohol (IPA) helps perovskite crystallization and leads to larger grain size from sequential deposition of perovskite films. The concentration of water was varied from 1% to 7% (vol% of IPA) in MAI solution and optical absorption, crystallization, morphology of perovskite films and their photovoltaic performance were studied in perovskite solar cells. 5% by volume was found to lead to preferential crystallization in the (110) plane with grain size about three times that of perovskite films prepared without adding water into the MAI solution. The optimal water concentration of 5% by volume in the MAI solution led to average perovskite grain size of ∼600 nm and solar cell efficiency of 12.42% at forward scan with a rate of 0.5 V s(-1). Device performance decreases after increasing water concentration beyond 5% in the MAI solution due to formation of the PbI2 phase. Transient photocurrent and photovoltage measurements show the shortest charge transport time at 0.99 μs and the longest charge carrier life time at 13.6 μs for perovskite films prepared from 5% water in MAI solution, which improved perovskite solar cell efficiency from 9.04% to 12.42%.

  15. A novel quasi-one-dimensional topological insulator in bismuth iodide β-Bi4I4

    Science.gov (United States)

    Autès, Gabriel; Isaeva, Anna; Moreschini, Luca; Johannsen, Jens C.; Pisoni, Andrea; Mori, Ryo; Zhang, Wentao; Filatova, Taisia G.; Kuznetsov, Alexey N.; Forró, László; van den Broek, Wouter; Kim, Yeongkwan; Kim, Keun Su; Lanzara, Alessandra; Denlinger, Jonathan D.; Rotenberg, Eli; Bostwick, Aaron; Grioni, Marco; Yazyev, Oleg V.

    2016-02-01

    Recent progress in the field of topological states of matter has largely been initiated by the discovery of bismuth and antimony chalcogenide bulk topological insulators (TIs; refs ,,,), followed by closely related ternary compounds and predictions of several weak TIs (refs ,,). However, both the conceptual richness of Z2 classification of TIs as well as their structural and compositional diversity are far from being fully exploited. Here, a new Z2 topological insulator is theoretically predicted and experimentally confirmed in the β-phase of quasi-one-dimensional bismuth iodide Bi4I4. The electronic structure of β-Bi4I4, characterized by Z2 invariants (1;110), is in proximity of both the weak TI phase (0;001) and the trivial insulator phase (0;000). Our angle-resolved photoemission spectroscopy measurements performed on the (001) surface reveal a highly anisotropic band-crossing feature located at the point of the surface Brillouin zone and showing no dispersion with the photon energy, thus being fully consistent with the theoretical prediction.

  16. Copper iodide as inorganic hole conductor for perovskite solar cells with different thickness of mesoporous layer and hole transport layer

    Science.gov (United States)

    Huangfu, Minzan; Shen, Yue; Zhu, Gongbo; Xu, Kai; Cao, Meng; Gu, Feng; Wang, Linjun

    2015-12-01

    This study is the first to report the preparation of Copper iodide (CuI) thick films by means of convenient airbrush process and their application as inorganic hole transport layers (HTL) in organo-lead halide perovskite-based solar cells. CuI thick films exhibit high conductivity, wide-band-gap and solution-processable. Organo-lead halide perovskite solar cells with different thickness of mesoporous layers and CuI hole transport layers were fabricated. Performance of the cells were mainly controlled by the thickness of TiO2 mesoporous layers. Under optimized conditions, a power conversion efficiency of 5.8% has been achieved with short-circuit current density JSC of 22.3 mA/cm2, open-circuit voltage VOC of 614 mV and fill factor of 42%. However, the VOC remains low in comparison with the state of the art perovskite-based solar cells, which is attributed to the high recombination in CuI devices as determined by impedance spectroscopy.

  17. Effects of N-n-butyl Haloperidol Iodide on Myocardial Ischemia/Reperfusion Injury and Egr-1 Expression in Rat

    Institute of Scientific and Technical Information of China (English)

    Yan-Mei ZHANG; Gang-Gang SHI; Zhao TANG; Jin-Hong ZHENG; Wei-Qiu LI; Fu-Xiao GUO; Qiang-Yong JIA

    2006-01-01

    We have previously shown that N-n-butyl haloperidol iodide (F2) derived from haloperidol reduces ischemia/reperfusion-induced myocardial injury by blocking intracellular Ca2+ overload. This study tested the hypothesis that cardio-protection with F2 is associated with an attenuation in the expression of early growth response gene 1 (Egr-1). In an in vivo rat model of 60 min coronary occlusion followed by 180 min of reperfusion, treatment with F2 significantly reduced myocardial injury evidenced by the reduction in release of plasma creatine kinase, myocardial creatine kinase isoenzyme and lactate dehydrogenase. In cultured neonatal rat cardiomyocytes of hypoxia for 3 h and reoxygenation for 1 h, F2 treatment attenuated necrotic and apoptotic cell death, as demonstrated by electron microscopy. Concomitant with cardio-protection by F2, the increased expression levels of Egr-1 mRNA and proteinwere significantly reduced in myocardial tissue and cultured cardiomyocytes as detected by reverse transcription-polymerase chain reaction, immunohistochemistry and immunocytochemistry. In conclusion, these results suggest that the protective effect of F2 on ischemia/reperfusion- or hypoxia/reoxygenation-induced myocardial injury might be partly mediated by downregulating Egr-1 expression.

  18. Experimental Study of Closed System in the Chlorine Dioxide-Iodide-Sulfuric Acid Reaction by UV-Vis Spectrophotometric Method

    Science.gov (United States)

    Li, Na; Shi, Laishun; Wang, Xiaomei; Guo, Fang; Yan, Chunying

    2011-01-01

    The mole ratio r(r = [I−]0/[ClO2]0) has great influence on ClO2-I−-H2SO4 closed reaction system. By changing the initiate concentration of potassium iodide, the curve of absorbance along with the reaction time was obtained at 350 nm and 297 nm for triiodide ion, and 460 nm for iodine. The changing point of the absorbance curve's shape locates at r = 6.00. For the reaction of ClO2-I− in the absence of H2SO4, the curve of absorbance along with the reaction time can be obtained at 350 nm for triiodide ion, 460 nm for iodine. The mole ratio r is equal to 1.00 is the changing point of the curve's shape no matter at which wavelength to determine the reaction. For the reaction of ClO2-I−-H+ in different pH buffer solution, the curve of absorbance along with the reaction time was recorded at 460 nm for iodine. When r is greater than 1.00, the transition point of the curve's shape locates at pH 2.0, which is also the point of producing chlorite or chloride for chlorine dioxide at different pH. When r is less than 1.00, the transition point locates at pH 7.0. PMID:21808646

  19. Chlorine doping reduces electron-hole recombination in lead iodide perovskites: time-domain ab initio analysis.

    Science.gov (United States)

    Liu, Jin; Prezhdo, Oleg V

    2015-11-19

    Rapid development in lead halide perovskites has led to solution-processable thin film solar cells with power conversion efficiencies close to 20%. Nonradiative electron-hole recombination within perovskites has been identified as the main pathway of energy losses, competing with charge transport and limiting the efficiency. Using nonadiabatic (NA) molecular dynamics, combined with time-domain density functional theory, we show that nonradiative recombination happens faster than radiative recombination and long-range charge transfer to an acceptor material. Doping of lead iodide perovskites with chlorine atoms reduces charge recombination. On the one hand, chlorines decrease the NA coupling because they contribute little to the wave functions of the valence and conduction band edges. On the other hand, chlorines shorten coherence time because they are lighter than iodines and introduce high-frequency modes. Both factors favor longer excited-state lifetimes. The simulation shows good agreement with the available experimental data and contributes to the comprehensive understanding of electronic and vibrational dynamics in perovskites. The generated insights into design of higher-efficiency solar cells range from fundamental scientific principles, such as the role of electron-vibrational coupling and quantum coherence, to practical guidelines, such as specific suggestions for chemical doping.

  20. Ionic and Optical Properties of Methylammonium Lead Iodide Perovskite across the Tetragonal-Cubic Structural Phase Transition

    Energy Technology Data Exchange (ETDEWEB)

    Hoque, Md Nadim Ferdous [Department of Electrical and Computer Engineering and Nano Tech Center, Texas Tech University, Lubbock Texas 79409 USA; Islam, Nazifah [Department of Electrical and Computer Engineering and Nano Tech Center, Texas Tech University, Lubbock Texas 79409 USA; Li, Zhen [Chemistry and Nanoscience Center, National Renewable Energy Laboratory, Golden Colorado 80401 USA; Ren, Guofeng [Department of Electrical and Computer Engineering and Nano Tech Center, Texas Tech University, Lubbock Texas 79409 USA; Zhu, Kai [Chemistry and Nanoscience Center, National Renewable Energy Laboratory, Golden Colorado 80401 USA; Fan, Zhaoyang [Department of Electrical and Computer Engineering and Nano Tech Center, Texas Tech University, Lubbock Texas 79409 USA

    2016-09-01

    Practical hybrid perovskite solar cells (PSCs) must endure temperatures above the tetragonal-cubic structural phase transition of methylammonium lead iodide (MAPbI3). However, the ionic and optical properties of MAPbI3 in such a temperature range, and particularly, dramatic changes in these properties resulting from a structural phase transition, are not well studied. Herein, we report a striking contrast at approximately 45 degrees C in the ionic/electrical properties of MAPbl3 owing to a change of the ion activation energy from 0.7 to 0.5 eV, whereas the optical properties exhibit no particular transition except for the steady increase of the bandgap with temperature. These observations can be explained by the 'continuous' nature of perovskite phase transition. We speculate that the critical temperature at which the ionic/electrical properties change, although related to crystal symmetry variation, is not necessarily the same temperature as when tetragonal-cubic structural phase transition occurs.

  1. The Synergistic Effect of Iodide and Sodium Nitrite on the Corrosion Inhibition of Mild Steel in Bicarbonate–Chloride Solution

    Directory of Open Access Journals (Sweden)

    Gaius Debi Eyu

    2016-10-01

    Full Text Available The effect of potassium iodide (KI and sodium nitrite (NaNO2 inhibitor on the corrosion inhibition of mild steel in chloride bicarbonate solution has been studied using electrochemical techniques. Potentiodynamic polarisation data suggest that, when used in combination, KI and NaNO2 function together to inhibit reactions at both the anode and the cathode, but predominantly anodic. KI/NO2− concentration ratios varied from 2:1 to 2:5; inhibition efficiency was optimized for a ratio of 1:1. The surface morphology and corrosion products were analysed using scanning electron microscopy (SEM and X-ray diffractometry (XRD. The latter shows that the addition of I− to NO2 facilitates the formation of a passivating oxide (γ-Fe2O3 as compared to NO2− alone, decreasing the rate of metal dissolution observed in electrochemical testing. The synergistic effect of KI/NO2− inhibition was enhanced under the dynamic conditions associated with testing in a rotating disc electrode.

  2. Bacterial photodynamic inactivation mediated by methylene blue and red light is enhanced by synergistic effect of potassium iodide.

    Science.gov (United States)

    Vecchio, Daniela; Gupta, Asheesh; Huang, Liyi; Landi, Giacomo; Avci, Pinar; Rodas, Andrea; Hamblin, Michael R

    2015-09-01

    The inexorable increase of antibiotic resistance occurring in different bacterial species is increasing the interest in developing new antimicrobial treatments that will be equally effective against multidrug-resistant strains and will not themselves induce resistance. One of these alternatives may be photodynamic inactivation (PDI), which uses a combination of nontoxic dyes, called photosensitizers (PS), excited by harmless visible light to generate reactive oxygen species (ROS) by type 1 (radical) and type 2 (singlet oxygen) pathways. In this study, we asked whether it was possible to improve the efficacy of PDI in vitro and in vivo by addition of the inert salt potassium iodide (KI) to a commonly investigated PS, the phenothiazinium dye methylene blue (MB). By adding KI, we observed a consistent increase of red light-mediated bacterial killing of Gram-positive and Gram-negative species in vitro and in vivo. In vivo, we also observed less bacterial recurrence in wounds in the days posttreatment. The mechanism of action is probably due to formation of reactive iodine species that are produced quickly with a short lifetime. This finding may have a relevant clinical impact by reducing the risk of amputation and, in some cases, the risk of death, leading to improvement in the care of patients affected by localized infections.

  3. Experimental Study of Closed System in the Chlorine Dioxide-Iodide-Sulfuric Acid Reaction by UV-Vis Spectrophotometric Method

    Directory of Open Access Journals (Sweden)

    Na Li

    2011-01-01

    Full Text Available The mole ratio r(r=[I−]0/[ClO2]0 has great influence on ClO2-I−-H2SO4 closed reaction system. By changing the initiate concentration of potassium iodide, the curve of absorbance along with the reaction time was obtained at 350 nm and 297 nm for triiodide ion, and 460 nm for iodine. The changing point of the absorbance curve's shape locates at r=6.00. For the reaction of ClO2-I− in the absence of H2SO4, the curve of absorbance along with the reaction time can be obtained at 350 nm for triiodide ion, 460 nm for iodine. The mole ratio r is equal to 1.00 is the changing point of the curve's shape no matter at which wavelength to determine the reaction. For the reaction of ClO2-I−-H+ in different pH buffer solution, the curve of absorbance along with the reaction time was recorded at 460 nm for iodine. When r is greater than 1.00, the transition point of the curve's shape locates at pH 2.0, which is also the point of producing chlorite or chloride for chlorine dioxide at different pH. When r is less than 1.00, the transition point locates at pH 7.0.

  4. Growth and characterization of potassium strontium iodide: A new high light yield scintillator with 2.4% energy resolution

    Science.gov (United States)

    Stand, L.; Zhuravleva, M.; Lindsey, A.; Melcher, C. L.

    2015-04-01

    A new ternary metal halide scintillator, potassium strontium iodide, activated with divalent europium (KSr2I5:Eu) has been discovered. This material has a monoclinic crystal structure with a density of 4.39 g/cm3. Differential scanning calorimetry indicates a congruent melting point of 470 °C and suggests that this compound has no solid-solid phase transitions. As is the case with most metal halides, the material is hygroscopic, and it has some internal radioactivity due to the presence of 40K. Single crystals of KSr2I5 doped with 4% Eu2+ were grown in evacuated quartz ampoules via the Bridgman technique. The X-ray excited emission spectrum consisted of a single peak at ~445 nm due to the 5d-4f transition in Eu2+. The measured light yield is ~94,000 photons/MeV with an energy resolution of 2.4% at 662 keV. The crystal has an excellent proportionality response over a wide range of energies from 14 keV to 1275 keV.

  5. Effect of potassium iodide on luminescent and photovoltaic properties of organic solar cells P3HT-PCBM

    Science.gov (United States)

    Ibrayev, N. Kh; Afanasyev, D. A.; Zhapabaev, K. A.

    2016-02-01

    It has been investigated spectral-luminescence properties of polymer films, doped with potassium iodide (KI). Using of KI didn't lead to the gradual changes of optical density of polymer films and the range of band gap semiconductor polymer P3HT. The fluorescence intensity of P3HT decreased and changed by use of KI. Using of 1% KI in polymer leaded to decrease of fluorescence lifetime. Influence of heavy atom on photovoltaic effect of organic solar cells has been investigated. 1% of KI in polymer film leaded to decrease of Isc and slightly decrease of Uoc. Investigation shows that magnetic field does not affect on photovoltaic properties of cells P3HT-PCBM. Magnetic field increased of open circuit voltage and short circuit current of solar cells with 1% of KI. Study of electrical impedance of cells revealed the magnetic sensivity of solar cells with KI additives. The lifetime of free charge carriers increased in the magnetic field for solar cells with KI additives.

  6. Synergistic effects on iodine release in potassium iodide solution by combination of ultrasound and visible light irradiations

    Institute of Scientific and Technical Information of China (English)

    MA Chunying; XU Jianyi; LIU Xiaojun

    2008-01-01

    Iodine release in potassium iodide solution has been investigated under the irradi-ations of ultrasound and visible light respectively and simultaneously. We have observed that the amount of iodine liberated under the combined irradiation of ultrasound and visible light is larger than the sum of that under the respective irradiations of ultrasound and visible light,indicating a synergistic effect of ultrasound and visible light irradiations. Based on the investi-gation of the reaction kinetics of iodine liberated, we have ascribed the synergistic effect to the perfect stirring of the photochemical reactor induced by the applying simultaneous ultrasound.The ideal stirring can result in the homogenization of the primary light effect in the whole reac-tion medium, which induces the acceleration of the photochemical reaction. On behavior of our knowledge, there are few reports on the investigations of utilizing the combination of ultrasonic energy and hght energy to accelerate the reaction yield and rate as well as the kinetics of the reaction.

  7. Growth and studies of pure and potassium iodide-doped zinc tris-thiourea sulphate (ZTS) single crystals

    Science.gov (United States)

    Krishnan, C.; Selvarajan, P.; Freeda, T. H.

    2008-12-01

    Single crystals of pure and potassium iodide (KI)-doped Zinc Tris-thiourea Sulphate (ZTS) were grown from aqueous solutions by slow evaporation technique. The grown crystals have been subjected to single crystal X-ray diffraction to determine the unit cell dimensions. The grown crystals were also characterized by recording the powder X-ray diffraction patterns and by identifying the diffracting planes. The Fourier Transform Infrared (FT-IR) spectra have been recorded in the range 400-4500 cm -1. Second harmonic generation (SHG) for the materials of this work was confirmed using Nd:YAG laser. The UV-visible spectra show that the grown crystals have wide optical transparency in the entire visible region. The Thermogravimetric/Differential Thermal Analyses (TG/DTA) thermograms reveal that the materials have good thermal stability. Atomic absorption study reveals the presence of potassium in the doped f crystals. The electrical measurements were made in the temperature range 40-130 °C along c-direction of the grown crystals. The dielectric studies show that there may be a ferroelectric transition at 50 °C for both pure and KI-doped ZTS crystals. DC conductivity for both the samples is found to be increasing with increase in temperature. Activation energy values were also determined for both AC and DC conduction processes in the samples.

  8. Growth and characterization of pure and potassium iodide-doped zinc tris-thiourea sulphate (ZTS) single crystals

    Science.gov (United States)

    Krishnan, C.; Selvarajan, P.; Freeda, T. H.; Mahadevan, C. K.

    2009-02-01

    Single crystals of pure and potassium iodide (KI)-doped zinc tris-thiourea sulphate (ZTS) were grown from aqueous solutions by the slow evaporation method. The grown crystals were transparent. The lattice parameters of the grown crystals were determined by the single-crystal X-ray diffraction technique. The grown crystals were also characterized by recording the powder X-ray diffraction pattern and by identifying the diffracting planes. The FT-IR spectrum was recorded in the range 400-4500 cm -1. Second harmonic generation (SHG) was confirmed by the Kurtz powder method. The thermo gravimetric analysis (TGA) and differential thermal analysis (DTA) studies reveal that the materials have good thermal stability. Atomic absorption studies confirm the presence of dopant in ZTS crystals. The electrical measurements were made in the frequency range 10 2-10 6 Hz and in the temperature range 40-130 °C along a-, b- and c-directions of the grown crystals. The present study shows that the electrical parameters viz. dc conductivity, dielectric constant, dielectric loss factor and ac conductivity increase with increase in temperature. Activation energy values were also determined for the ac conduction process in grown crystals. The dc conductivity, dielectric constant, dielectric loss factor and ac conductivity of KI-doped ZTS crystal were found to be more than those of pure ZTS crystals.

  9. A thalium-doped sodium iodide well counter for radioactive tracer applications with naturally-abundant 40K

    Science.gov (United States)

    Parker, Andrew J.; Boxall, Colin; Joyce, Malcolm J.; Schotanus, Paul

    2013-09-01

    The use of a thallium-doped sodium-iodide well-type scintillation detector for the assay of the low-activity radioisotope 40K, in open-source potassium chloride aqueous solutions, is described. The hazards, safety concerns and radiowaste generation associated with using open-source radioactive isotopes can present significant difficulties, the use of hot cells and escalated costs in radioanalytical laboratory research. A solution to this is the use of low-hazard alternatives that mimic the migration and dispersion characteristics of notable fission products (in this case 137Cs). The use of NaI(Tl) as a detection medium for naturally-abundant levels of 40K in a range of media is widespread, but the use of 40K as a radioactive tracer has not been reported. The use of such low-activity sources is often complicated by the ability to detect them efficiently. In this paper a scintillator detector designed to detect the naturally-abundant 40K present in potassium chloride in tracer applications is described. Examples of the use of potassium chloride as a tracer are given in the context of ion exchange and electrochemical migration studies, and comparisons in performance are drawn from literature with hyper pure germanium semiconductor detectors, which are more commonly utilised detectors in high-resolution counting applications.

  10. Polycrystalline lead iodide films produced by solution evaporation and tested in the mammography X-ray energy range

    Science.gov (United States)

    Condeles, J. F.; Mulato, M.

    2016-02-01

    Lead iodide polycrystalline films have been deposited on corning glass substrates using solution evaporation in oven. Films 6 μm-thick were obtained with full coverage of the substrates as verified by scanning electron microscopy. Some pin-holes were observable. X-ray diffraction revealed a crystalline structure corresponding to the 4 H-PbI2 polytype formation. Polarized Raman scattering experiments indicated a lamellar structure. Anisotropy was also investigated using depolarization ratio calculations. The optical and electrical properties of the samples were investigated using photoluminescence and dark conductivity as a function of temperature, respectively. Activation energies of 0.10 up to 0.89 eV were related to two main electrical transport mechanisms. Films were also exposed to X-ray irradiation in the mammography X-ray energy range. The detector produced was also exposed to X-ray from 5 mR up to 1450 mR. A linear response was observed as a function of dose with a slope of 0.52 nA/mm2 per mR.

  11. Formation and Characterization of Mixed Crystals Based on Bis (ThioureaCadmium Chloride and Bis (ThioureaCadmium Iodide

    Directory of Open Access Journals (Sweden)

    I.S. Prameela Kumar

    2014-07-01

    Full Text Available Bis(thioureacadmium chloride(BTCC and bis(thioureacadmium iodide (BTCI are metal complexes of thiourea having better nonlinear optical properties than KH2PO4. An attempt has been made in the present study to form mixed crystals based on BTCC and BTCI (even though their crystal lattices mismatch from aqueous solutions, the precursors mixed in proper proportions. A total of seven (including the end members crystals were formed by the free evaporation method and characterized chemically, structurally, thermally, optically and electrically. The X-ray diffraction measurements indicate that (BTCCX(BTCI1-X crystals with x=1.0,0.8 and 0.6 are orthorhombic in structure with space group Pmn21 and that with x=0.5, 0.4, 0.2 and 0.0 are monoclinic in structure with space group P21/c. All the grown crystals are found to be thermally stable up to 215 °C and possessing wide optical transmission window (300-900 nm which is suitable for NLO applications. The electrical measurements indicate that the grown crystals exhibit a normal dielectric behavior. The results obtained in the present study indicate that mixed crystals can be formed from the isomorphous precursors directly even though the end member’s crystals have lattice mismatching.

  12. Radioiodine Therapy of Liver Cancer Cell Following Tissue Specific Sodium Iodide Symporter Gene Transfer and Assessment of Therapeutic Efficacy with Optical Imaging

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Byoung Kuk; Lee, You La; Lee, Yong Jin [School of Medicine, Kyungpook National University, Daegu (Korea, Republic of)] (and others)

    2008-10-15

    Cancer specific killing can be achieved by therapeutic gene activated by cancer specific promotor. Expression of sodium iodide symporter (NIS) gene causes transportation and concentration of iodide into the cell, therefore radioiodine treatment after NIS gene transfer to cancer cell could be a form of radionuclide gene therapy. luciferase (Luc) gene transfected cancer cell can be monitored by in vivo optical imaging after D-luciferin injection. Aims of the study are to make vector with both therapeutic NIS gene driven by AFP promoter and reporter Luc gene driven by CMV promoter, to perform hepatocellular carcinoma specific radiodiodine gene therapy by the vector, and assessment of the therapy effect by optical imaging using luciferase expression. A Vector with AFP promoter driven NIS gene and CMV promoter driven Luc gene (AFP-NIS-CMV-Luc) was constructed. Liver cancer cell (HepG2, Huh-7) and non liver cancer cell (HCT-15) were transfected with the vector using liposome. Expression of the NIS gene at mRNA level was elucidated by RT-PCR. Radioiodide uptake, perchlorate blockade, and washout tests were performed and bioluminescence also measured by luminometer in these cells. In vitro clonogenic assay with I-131 was performed. In vivo nuclear imaging was obtained with gamma camera after I-131 intraperitoneal injection. A Vector with AFP-NIS-CMV-Luc was constructed and successfully transfected into HepG2, Huh-7 and HCT-15 cells. HepG2 and Huh-7 cells with AFP-NIS-CMV-Luc gene showed higher iodide uptake than non transfected cells and the higher iodide uptake was totally blocked by addition of perchlorate. HCT-15 cell did not showed any change of iodide uptake by the gene transfection. Transfected cells had higher light output than control cells. In vitro clonogenic assay, transfected HepG2 and Huh-7 cells showed lower colony count than non transfected HepG2 and Huh-7 cells, but transfected HCT-15 cell did not showed any difference than non transfected HCT-15 cell

  13. Effects of iodine and thyroid hormones in inducing and treating Hashimoto's thyroiditis; Effekte von Iodid und Schilddruesenhormonen bei der Induktion und Therapie einer Thyreoiditis Hashimoto

    Energy Technology Data Exchange (ETDEWEB)

    Rink, T.; Schroth, H.J.; Holle, L.H.; Garth, H. [Stadtkrankenhaus Hanau (Germany). Abt. fuer Nuklearmedizin

    1999-07-01

    Aim: The effect of an iodine prophylaxis on the induction of Hashimoto's thyroiditis as well as the influence of various therapeutic approaches on the course of antithyroglobulin (TgAb) and antiperoxidase (TPOAb) antibodies in manifest diseases are evaluated. Method: A collective of 375 euthyroid subjects without relevant goiter received daily doses of 200 micrograms iodide, weekly doses of 1.53 milligrams iodide, or no medication. A second group of 377 patients suffering from Hashimoto's thyroiditis was treated with a non-suppressive hormone medication, a suppressive hormone administration, a combination of a non-suppressive hormone therapy with low dose iodide (50-150 micrograms/day), mere iodide in doses of 200 micrograms/day, or received no therapy. The mean observation period in these two groups was 860 and 848 days, respectively. Results: There was no significant increase of the antibody levels in the subgroup with 200 micrograms iodide/day and in the non-treated subjects of the first collective. However, the group that received 1.53 milligrams iodide/week presented a distinct increase of the TgAb as well as the TPOAb, and the incidence of Hashimoto's thyroiditis was 4-fold higher than in the two other subgroups. The patients of the second collective revealed a sinificant decrease of the TgAb in the subgroups treated with up to 200 micrograms iodide/day, while the reduction of the TPOAb depended on the thyrotropin level and was most significant in the suppressed group (p<0.0001). Conclusion: To lower the incidence of autoimmune thyroid diseases in predisposed subjects, a daily iodine supplementation seems to be superior to high-dose weekly administrations. A hormone therapy combined with a daily, low-dose iodine medication is able to reduce the TgAb and the TPOAb levels even in patients with Hashimoto's thyroidits. (orig.) [German] Ziel: Untersucht wurden der Einfluss einer Iodprophylaxe auf die Inzidenz einer Autoimmunthyreoiditis bzw

  14. A first-principles based study of ns2 containing ternary iodides and their possibility of scintillation

    Science.gov (United States)

    Kang, Byungkyun; Fang, C. M.; Biswas, Koushik

    2016-10-01

    A recently investigated scintillator material CsBa2I5 showed promising properties when activated with ns2 ions In+, Tl+ or the lanthanide Eu2+. This sparked our interest in an analogous group of materials, e.g. InBa2I5 or TlBa2I5 where the ns2 ion is part of the crystal framework, replacing the alkali ion. Many of these compounds of the type AB2X5 (X  =  halogen) have been previously synthesized and have interesting stereochemical activity. Using density functional calculations we have studied the stable monoclinic phase of the aforementioned ns2 containing iodides. One objective is to explore them as scintillators where the ns2 ions, now appearing as part of the crystal, play a central role. Compared to CsBa2I5, their reduced fundamental band gap and possibility of higher light yield may be attributed to an induced degree of covalency in the ns2-I bonds. The valence and conduction band edges have discernible contributions from the ns2 ions’ s and p orbitals which is crucial in carrier localization. The antibonding Ga or In s sates near valence edge may be a favored site for a hole trap, as against a {{V}k} center. Additional differences among the ns2 compounds lead to qualitatively different self-trapped excitons that may fundamentally affect luminescence. The possibility of fast electron capture at the ns2 sites and the prospect of self-activated scintillation via ns2-p  →  {{V}k} or ns2-p  →  ns2-s transitions may draw interest in related applications.

  15. Determination of major sodium iodide symporter (NIS) inhibitors in drinking waters using ion chromatography with conductivity detector.

    Science.gov (United States)

    Cengiz, Mehmet Fatih; Bilgin, Ayse Kevser

    2016-02-20

    Goiter is an important health problem all over the world and iodine deficiency is its most common cause. Perchlorate, thiocyanate and nitrate (called as major NIS inhibitors) are known to competitively inhibit iodide uptake by the thyroid gland and thus, human exposure to major NIS inhibitors is a public health concern. In this study, an ion chromatographic method for the determination of most common NIS inhibitor ions in drinking waters was developed and validated. This is the first study where an analytical method is used for the determination of major NIS inhibitors in drinking water by an ion chromatography system in a single run. Chromatographic separations were achieved with an anion-exchange column and separated ions were identified by a conductivity detector. The method was found to be selective, linear, precise accurate and true for all of interested ions. The limits of the detections (LOD) were estimated at 0.003, 0.004 and 0.025mgL(-1) for perchlorate, thiocyanate and nitrate, respectively. Possible interference ions in drinking waters were examined for the best separation of NIS inhibitors. The excellent method validation data and proficiency test result (Z-score for nitrate: -0.1) of the FAPAS(®) suggested that the developed method could be applied for determination of NIS inhibitor residues in drinking waters. To evaluate the usefulness of the method, 75 drinking water samples from Antalya/Turkey were analyzed for NIS inhibitors. Perchlorate concentrations in the samples ranged from not detected (less than LOD) to 0.07±0.02mgL(-1) and the range of nitrate concentrations were found to be 3.60±0.01mgL(-1) and 47.42±0.40mgL(-1). No thiocyanate residues were detected in tested drinking water samples.

  16. Treatment of medulloblastoma using an oncolytic measles virus encoding the thyroidal sodium iodide symporter shows enhanced efficacy with radioiodine

    Directory of Open Access Journals (Sweden)

    Hutzen Brian

    2012-11-01

    Full Text Available Abstract Background Medulloblastoma is the most common malignant brain tumor of childhood. Although the clinical outcome for medulloblastoma patients has improved significantly, children afflicted with the disease frequently suffer from debilitating side effects related to the aggressive nature of currently available therapy. Alternative means for treating medulloblastoma are desperately needed. We have previously shown that oncolytic measles virus (MV can selectively target and destroy medulloblastoma tumor cells in localized and disseminated models of the disease. MV-NIS, an oncolytic measles virus that encodes the human thyroidal sodium iodide symporter (NIS, has the potential to deliver targeted radiotherapy to the tumor site and promote a localized bystander effect above and beyond that achieved by MV alone. Methods We evaluated the efficacy of MV-NIS against medulloblastoma cells in vitro and examined their ability to incorporate radioiodine at various timepoints, finding peak uptake at 48 hours post infection. The effects of MV-NIS were also evaluated in mouse xenograft models of localized and disseminated medulloblastoma. Athymic nude mice were injected with D283med-Luc medulloblastoma cells in the caudate putamen (localized disease or right lateral ventricle (disseminated disease and subsequently treated with MV-NIS. Subsets of these mice were given a dose of 131I at 24, 48 or 72 hours later. Results MV-NIS treatment, both by itself and in combination with 131I, elicited tumor stabilization and regression in the treated mice and significantly extended their survival times. Mice given 131I were found to concentrate radioiodine at the site of their tumor implantations. In addition, mice with localized tumors that were given 131I either 24 or 48 hours after MV-NIS treatment exhibited a significant survival advantage over mice given MV-NIS alone. Conclusions These data suggest MV-NIS plus radioiodine may be a potentially useful therapy for

  17. New analysis of the ν6 and 2ν3 bands of methyl iodide (CH3I)

    Science.gov (United States)

    Perrin, A.; Haykal, I.; KwabiaTchana, F.; Manceron, L.; Doizi, D.; Ducros, G.

    2016-06-01

    A new rovibrational study of the ν6 band of methyl iodide was conducted to obtain a rather complete line list. A new analysis of line positions was accomplished. The spectrum of this band has been first recorded using the Bruker IFS125HR Fourier transform spectrometer (FTS) at the AILES beamline of the SOLEIL Synchrotron facility and later with the Bruker IFS125HR FTS located at the LISA facility in Créteil. Altogether, about 10,000 lines were assigned for the ν6 and 2ν3 bands up to high quantum numbers (J ⩽ 85 and K ⩽ 20). Because of the large value of the 127I nuclear quadrupole hyperfine constant, a significant portion of these assignments concerns clusters of hyperfine subcomponents, which are easily observable at 11 μm. These infrared data were combined in a least squares fit together with the existing microwave data on rotational transitions within the v6 = 1 and v3 = 2 vibrational states to get the upper state rotational constants and interacting parameters for the v6 = 1 and v3 = 2 states. Due to the high values of quantum numbers achieved during this infrared analysis, the final energy level calculation accounts for aCx (Δℓ = ± 1; ΔK = ± 1) and an α (Δℓ = ∓ 1; ΔK = ± 2) types of Coriolis interactions coupling the v6 = 1 energy levels with those from the v3 = 2 and v2 = 1 states, respectively. On the other hand, it proved unnecessary to update the existing hyperfine parameters for the v6 = 1 and v3 = 2 states.

  18. In situ investigation of the formation and metastability of formamidinium lead tri-iodide perovskite solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Aguiar, Jeffery A.; Wozny, Sarah; Holesinger, Terry G.; Aoki, Toshihiro; Patel, Maulik K.; Yang, Mengjin; Berry, Joseph J.; Al-Jassim, Mowafak; Zhou, Weilie; Zhu, Kai

    2016-01-01

    Organic-inorganic perovskites have emerged as an important class of next generation solar cells due to their remarkably low cost, band gap, and sub-900 nm absorption onset. Here, we show a series of in situ observations inside electron microscopes and X-ray diffractometers under device-relevant synthesis conditions focused on revealing the crystallization process of the formamidinium lead-triiodide perovskite at the optimum temperature of 175 degrees C. Direct in situ observations of the structure and chemistry over relevant spatial, temporal, and temperature scales enabled identification of key perovskite formation and degradation mechanisms related to grain evolution and interface chemistry. The lead composition was observed to fluctuate at grain boundaries, indicating a mobile lead-containing species, a process found to be partially reversible at a key temperature of 175 degrees C. Using low energy electron microscopy and valence electron energy loss spectroscopy, lead is found to be bonded in the grain interior with iodine in a tetrahedral configuration. At the grain boundaries, the binding energy associated with lead is consequently shifted by nearly 2 eV and a doublet peak is resolved due presumably to a greater degree of hybridization and the potential for several different bonding configurations. At the grain boundaries there is adsorption of hydrogen and OH- ions as a result of residual water vapor trapped as a non-crystalline material during formation. Insights into the relevant formation and decomposition reactions of formamidinium lead iodide at low to high temperatures, observed metastabilities, and relationship with the photovoltaic performance were obtained and used to optimize device processing resulting in conversion efficiencies of up to 17.09% within the stability period of the devices.

  19. Low-temperature phases of rubidium silver iodide: crystal structures and dynamics of the mobile silver ions.

    Science.gov (United States)

    Funke, Klaus; Banhatti, Radha D; Wilmer, Dirk; Dinnebier, Robert; Fitch, Andrew; Jansen, Martin

    2006-03-09

    Recently, broad-band conductivity spectra have been taken in the low-temperature gamma-phase of the archetypal fast ion conductor RbAg4I5. Attempts to reproduce the experimental data in a simple model calculation have led to the conclusion that strictly localized displacive movements of interacting ionic charge carriers should play an important role in the low-temperature phase. However, with no detailed structural study of gamma-RbAg4I5 available, the relevant processes could not be identified within the crystal structure. This state of affairs has triggered the present investigation of the structures of all three phases of rubidium silver iodide. Powder diffraction data of RbAg4I5 have been collected at the high-resolution powder diffractometer at ID31 at the European Synchrotron Radiation Facility (ESRF). The structure of the gamma-phase has been solved by successive Rietveld refinements in combination with difference Fourier analyses. The same structural principle is found to prevail in all three phases, interconnected distorted RbI6 octahedra forming a three-dimensional framework, which undergoes only displacive structural changes during the alpha-beta and beta-gamma phase transitions. With decreasing temperature, the disorder in the silver sublattice is found to decrease, and a clustering of the disordered silver ions is found to develop. In the gamma-phase, "pockets" containing partially occupied silver sites have been identified, and it is suggested that the localized displacive motion detected by conductivity spectroscopy is performed by the silver ions located within these pockets.

  20. Biosynthesis of ascaridole: iodide peroxidase-catalyzed synthesis of a monoterpene endoperoxide in soluble extracts of Chenopodium ambrosioides fruit.

    Science.gov (United States)

    Johnson, M A; Croteau, R

    1984-11-15

    Ascaridole, an asymmetric monoterpene endoperoxide with anthelmintic properties, occurs as a major constituent (60-80%) in the volatile oil of American wormseed fruit (Chenopodium ambrosioides: Chenopodiaceae), and as a lesser component in the leaf pocket oil of the boldo tree (Peumus boldus: Monimiaceae). Determination of optical activity and chromatographic resolution of naturally occurring ascaridole, and several synthetic derivatives, showed that both wormseed and boldo produce ascaridole in racemic form. The biosynthesis of ascaridole from the conjugated, symmetrical diene alpha-terpinene (a major component of the oil from wormseed) was shown to be catalyzed by a soluble iodide peroxidase isolated from homogenates of C. ambrosioides fruit and leaves. The enzymatic synthesis of ascaridole was confirmed by capillary gas-liquid chromatography and mass spectrometry of the product, which was also shown to be racemic. Optimal enzymatic activity occurred at pH 4.0 in the presence of 2.5 mM H2O2 and 1 mM NaI. Soluble enzyme extracts were fractionated by gel filtration on both Sephacryl S-300 and Sephadex G-100, and were shown to consist of a high-molecular-weight peroxidase component (Mr greater than 1,000,000, 30% of total activity) and two other peroxidase species having apparent molecular weights of 62,000 and 45,000 (major component). Peroxidase activity was susceptible to proteolytic destruction only after periodate treatment, suggesting an association of the enzyme(s) with polysaccharide material. Ascaridole biosynthesis from alpha-terpinene was inhibited by cyanide, catalase, and reducing agents, but not by compounds that trap superoxide or quench singlet oxygen. A peroxide transfer reaction initiated by peroxidase-generated I+ is proposed for the conversion of alpha-terpinene to ascaridole.

  1. The antimicrobial effect of iodine-potassium iodide after cleaning and shaping procedures in mesial root canals of mandibular molars.

    Science.gov (United States)

    Tello-Barbaran, Javier; Nakata, Hilda Moromi; Salcedo-Moncada, Doris; Bramante, Clovis M; Ordinola-Zapata, Ronald

    2010-01-01

    The aim of this study was to evaluate the antibacterial activity of 2% iodine potassium iodide (IKI) used as a final rinse after the cleaning and shaping procedures in mesial root canals of mandibular molars infected with Enterococcus faecalis. Seventy two mandibular first molars were used. The root canals were infected with Enterococcus faecalisfor 30 days. After the infection procedures, the root canals were cleaned and shaped by using the Pro Taper rotary system and manual files. The teeth were randomly assigned to four experimental groups (N = 18). In group 1, the root canals were irrigated with sterile distilled water (control). In group 2, the root canals were irrigated with 1% Sodium hypochlorite (NaOCl) during instrumentation. In group 3, root canals were irrigated with 1% NaOCl during instrumentation and a five minute final irrigation using 2% IKI. In group 4, the root canals were irrigated with 1% NaOCl during instrumentation and a 15 minutes final irrigation with 2% IKI. Bacteria colony-forming units (CFU) from root canals were semi-quantified and the presence of negative cultures among the groups was compared using Fisher's test (p < 0.05). The order of effectiveness was: 1% NaOCI plus 2% IKl for 15 minutes (95%), 1% NaOCl plus 2% IKl for 5 minutes (44%), 1% NaOCl (17%) and sterile distilled water (0%). Fisher's exact test showed a significant difference among the groups (p < 0.05). It was concluded that under in vitro conditions, IKI was able to eliminate the Enterococcus faecalis from infected dentin significantly in a 15-minute time frame after the cleaning and shaping procedures.

  2. Growth and characterization of potassium strontium iodide: A new high light yield scintillator with 2.4% energy resolution

    Energy Technology Data Exchange (ETDEWEB)

    Stand, L., E-mail: lstand@utk.edu [Scintillation Materials Research Center, University of Tennessee, Knoxville, TN (United States); Materials Science and Engineering, University of Tennessee, Knoxville, TN (United States); Zhuravleva, M.; Lindsey, A. [Scintillation Materials Research Center, University of Tennessee, Knoxville, TN (United States); Materials Science and Engineering, University of Tennessee, Knoxville, TN (United States); Melcher, C.L. [Scintillation Materials Research Center, University of Tennessee, Knoxville, TN (United States)

    2015-04-21

    A new ternary metal halide scintillator, potassium strontium iodide, activated with divalent europium (KSr{sub 2}I{sub 5}:Eu) has been discovered. This material has a monoclinic crystal structure with a density of 4.39 g/cm{sup 3}. Differential scanning calorimetry indicates a congruent melting point of 470 °C and suggests that this compound has no solid–solid phase transitions. As is the case with most metal halides, the material is hygroscopic, and it has some internal radioactivity due to the presence of {sup 40}K. Single crystals of KSr{sub 2}I{sub 5} doped with 4% Eu{sup 2+} were grown in evacuated quartz ampoules via the Bridgman technique. The X-ray excited emission spectrum consisted of a single peak at ~445 nm due to the 5d–4f transition in Eu{sup 2+}. The measured light yield is ~94,000 photons/MeV with an energy resolution of 2.4% at 662 keV. The crystal has an excellent proportionality response over a wide range of energies from 14 keV to 1275 keV. - Highlights: • New Eu{sup 2+}-doped scintillators KSr{sub 2}I{sub 5}. • Single crystals of KSr{sub 2}I{sub 5}:Eu 4% were grown using the Bridgman technique. • This new material exhibit excellent properties for X-ray and gamma-ray detections. • Light yield of 94,000 ph/MeV and energy resolution of 2.4% at 662 keV.

  3. Highly efficient organic solar Cells based on a robust room-temperature solution-processed copper iodide hole transporter

    KAUST Repository

    Zhao, Kui

    2015-07-30

    Achieving high performance and reliable organic solar cells hinges on the development of stable and energetically suitable hole transporting buffer layers in tune with the electrode and photoactive materials of the solar cell stack. Here we have identified solution-processed copper(I) iodide (CuI) thin films with low-temperature processing conditions as an effective hole–transporting layer (HTL) for a wide range of polymer:fullerene bulk heterojunction (BHJ) systems. The solar cells using CuI HTL show higher power conversion efficiency (PCE) in standard device structure for polymer blends, up to PCE of 8.8%, as compared with poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) HTL, for a broad range of polymer:fullerene systems. The CuI layer properties and solar cell device behavior are shown to be remarkably robust and insensitive to a wide range of processing conditions of the HTL, including processing solvent, annealing temperature (room temperature up to 200 °C), and film thickness. CuI is also shown to improve the overall lifetime of solar cells in the standard architecture as compared to PEDOT:PSS. We further demonstrate promising solar cell performance when using CuI as top HTL in an inverted device architecture. The observation of uncommon properties, such as photoconductivity of CuI and templating effects on the BHJ layer formation, are also discussed. This study points to CuI as being a good candidate to replace PEDOT:PSS in solution-processed solar cells thanks to the facile implementation and demonstrated robustness of CuI thin films.

  4. Uranium, Cesium, and Mercury Leaching and Recovery from Cemented Radioactive Wastes in Sulfuric Acid and Iodide Media

    Directory of Open Access Journals (Sweden)

    Nicolas Reynier

    2015-11-01

    Full Text Available The Canadian Nuclear Laboratories (CNL is developing a long-term management strategy for its existing inventory of solid radioactive cemented wastes, which contain uranium, mercury, fission products, and a number of minor elements. The composition of the cemented radioactive waste poses significant impediments to the extraction and recovery of uranium using conventional technology. The goal of this research was to develop an innovative method for uranium, mercury and cesium recovery from surrogate radioactive cemented waste (SRCW. Leaching using sulfuric acid and saline media significantly improves the solubilization of the key elements from the SRCW. Increasing the NaCl concentration from 0.5 to 4 M increases the mercury solubilization from 82% to 96%. The sodium chloride forms a soluble mercury complex when mercury is present as HgO or metallic mercury but not with HgS that is found in 60 °C cured SRCW. Several leaching experiments were done using a sulfuric acid solution with KI to leach SRCW cured at 60 °C and/or aged for 30 months. Solubilization yields are above 97% for Cs and 98% for U and Hg. Leaching using sulfuric acid and KI improves the solubilization of Hg by oxidation of Hg0, as well as HgS, and form a mercury tetraiodide complex. Hg and Cs were selectively removed from the leachate prior to uranium recovery. It was found that U recovery from sulfuric leachate in iodide media using the resin Lewatit TP260 is very efficient. Considering these results, a process including effluent recirculation was applied. Improvements of solubilization due to the recycling of chemical reagents were observed during effluent recirculation.

  5. Gas phase synthesis, structure and unimolecular reactivity of silver iodide cluster cations, Ag(n)I(m)(+) (n = 2-5, 0 < m < n).

    Science.gov (United States)

    Khairallah, George N; O'Hair, Richard A J

    2008-06-14

    Multistage mass spectrometry (MS(n)) experiments reveal that gas phase silver iodide cluster cations, Ag(n)I(m)(+), are readily built up in a stepwise fashion via ion-molecule reactions between mass selected silver (Ag(3)(+) and Ag(5)(+)) or silver hydride (Ag(2)H(+) and Ag(4)H(+)) cluster cations and allyl iodide, in contrast to their reactions with methyl iodide, which solely result in ligation of the clusters. The stoichiometries of these clusters range from 1 clusters. Collision induced dissociation (CID) experiments were carried out on each of these clusters to shed some light on their possible structures. The products arising from CID of the Ag(n)I(m)(+) clusters are highly dependent on the stoichiometry of the cluster. Thus the odd-electron clusters Ag(4)I(2)(+) and Ag(5)I(+) fragment via loss of a silver atom. In contrast, the even-electron cluster ions all fragment via loss of AgI. In addition, Ag(2)I(2) loss is observed for the Ag(4)I(3)(+) and Ag(5)I(2)(+) clusters, while loss of Ag(3)I(3) occurs for the stoichiometric Ag(5)I(4)(+) cluster. DFT calculations were carried out on these Ag(n)I(m)(+) clusters as well as the neutrals associated with the ion-molecule and CID reactions. A range of different isomeric structures were calculated and their structures are described. A noteworthy aspect is that ligation of these silver clusters by I can have a profound effect on the geometry of the silver cluster. For example, D(3h) Ag(3)(+) becomes C(2v) Ag(3)I(+), which in turn becomes C(2h) Ag(3)I(2)(+). Finally, the DFT predicted thermochemistry supports the different types of reaction channels observed in the ion-molecule reactions and CID experiments.

  6. Influence of metal to ligand molar ratios on the supramolecular structure formation of Cu(II) with diaminopropane and iodide: Synthesis, structure, spectroscopic and DFT studies

    Science.gov (United States)

    Kharediya, Bhagwan; Shukla, Madhulata; Saha, Satyen; Sunkari, Sailaja

    2014-03-01

    Two new copper(II) complexes with 1,3-diaminopropane and iodide, viz., [{Cu ((1,3-diaminopropane)2 I (I3))}] (1) and [{Cu ((1,3 diaminopropane)2(I)2)}] (2) have been synthesized under self assembly conditions and structurally characterised to observe the structural variations brought about by varying ligand molar ratios, towards studying the effect of external factors on supramolecular structure formation, with a long term goal of obtaining magnetic materials. Corresponding to the variation in metal to ligand molar ratios from one to two, totally different products are obtained whose gross structural features are entirely different. The formation of 1, is unpredicted under given synthetic conditions and hence is interesting. The formation of 2, is as generally expected for the reacting components under given conditions. In case of 1, the metal ion's choice to adopt a square pyramidal geometry by coordinating to two ligand units and a coordinated iodide, even in the absence of sufficient moles of ligand, as in 2, is due to sub-molar ligand ratios complemented by weak hydrogen bonding interactions, operating between the ligand amino hydrogens and coordinated iodide and uncoordinated triiodide moiety. This approach of providing sub-molar amounts of ligand to the metal to satisfy its coordination requirements, appear to be a promising strategy towards obtaining novel solid systems of material relevance. Both the complexes are characterised structurally and spectroscopically. Further, both the structures were satisfactorily modelled by calculations based on Density Functional Theory (DFT), and their UV-visible spectra were analyzed in depth with the help of Time Dependent DFT (TD-DFT).

  7. Performance characteristics of guanine incorporated PVDF-HFP/PEO polymer blend electrolytes with binary iodide salts for dye-sensitized solar cells

    Science.gov (United States)

    Senthil, R. A.; Theerthagiri, J.; Madhavan, J.; Arof, A. K.

    2016-08-01

    In this work, we have investigated the influence of guanine as an organic dopant in dye-sensitized solar cell (DSSC) based on poly(vinylidinefluoride-co-hexafluoropropylene) (PVDF-HFP)/polyethylene oxide (PEO) polymer blend electrolyte along with binary iodide salts (potassium iodide (KI) and tetrabutylammonium iodide (TBAI)) and iodine (I2). The PVDF-HFP/KI + TBAI/I2, PVDF-HFP/PEO/KI + TBAI/I2 and guanine incorporated PVDF-HFP/PEO/KI + TBAI/I2 electrolytes were prepared by solution casting technique using DMF as solvent. The PVDF-HFP/KI + TBAI/I2 electrolyte showed an ionic conductivity value of 9.99 × 10-5 Scm-1, whereas, it was found to be increased to 4.53 × 10-5 Scm-1 when PEO was blended with PVDF-HFP/KI + TBAI/I2 electrolyte. However, a maximum ionic conductivity value of 3.67 × 10-4 Scm-1 was obtained for guanine incorporated PVDF-HFP/PEO/KI + TBAI/I2 blend electrolyte. The photovoltaic properties of all these polymer electrolytes in DSSCs were characterized. As a consequence, the power conversion efficiency of the guanine incorporated PVDF-HFP/PEO/KI + TBAI/I2 electrolyte based DSSC was significantly improved to 4.98% compared with PVDF-HFP/PEO/KI + TBAI/I2 electrolyte based DSSC (2.46%). These results revealed that the guanine can be an effective organic dopant to enhance the performance of DSSCs.

  8. Radiochemotherapy of hepatocarcinoma via lentivirus-mediated transfer of human sodium iodide symporter gene and herpes simplex virus thymidine kinase gene

    Energy Technology Data Exchange (ETDEWEB)

    Chen Libo, E-mail: libochen888@hotmail.com [Department of Nuclear Medicine, Shanghai Sixth People' s Hospital, Shanghai Jiao Tong University, Shanghai 200233 (China); Guo Guoying [Xinyuan Institute of Medicine and Biotechnology, School of Life Sciences, Zhejiang Sci-Tech University, Hangzhou 310018 (China); Liu Tianjing; Guo Lihe [Division of Biochemistry and Cell Biology, Shanghai Institute for Biological Sciences, Chinese Academy of Sciences, Shanghai 200031 (China); Zhu Ruisen [Department of Nuclear Medicine, Shanghai Sixth People' s Hospital, Shanghai Jiao Tong University, Shanghai 200233 (China)

    2011-07-15

    Herpes simplex virus thymidine kinase (HSV-TK) gene/ganciclovir (GCV) system has been widely used as a traditional gene therapy modality, and the sodium/iodide symporter gene (NIS) has been found to be a novel therapeutic gene. Since the therapeutic effects of radioiodine therapy or prodrug chemotherapy on cancers following NIS or HSV-TK gene transfer need to be enhanced, this study was designed to investigate the feasibility of radiochemotherapy for hepatocarcinoma via coexpression of NIS gene and HSV-TK gene. Methods: HepG2 cells were stably transfected with NIS, TK and GFP gene via recombinant lentiviral vector and named HepG2/NTG. Gene expression was examined by reverse transcriptase polymerase chain reaction, fluorescence imaging and iodide uptake. The therapeutic effects were assessed by MTT assay and clonogenic assay. Results: HepG2/NTG cells concentrated {sup 125}I{sup -} up to 76-fold higher than the wild-type cells within 20 min, and the efflux happened with a T{sub 1/2eff} of less than 10 min. The iodide uptake in HepG2/NTG cells was specifically inhibited by sodium perchlorate. Dose-dependent toxicity to HepG2/NTG cells by either GCV or {sup 131}I was revealed by clonogenic assay and MTT assay, respectively. The survival rate of HepG2/NTG cells decreased to 49.7%{+-}2.5%, 43.4%{+-}2.8% and 8.6%{+-}1.2% after exposure to {sup 131}I, GCV and combined therapy, respectively. Conclusion: We demonstrate that radiochemotherapy of hepatocarcinoma via lentiviral-mediated coexpression of NIS gene and HSV-TK gene leads to stronger killing effect than single treatment, and in vivo studies are needed to verify these findings.

  9. Sequence-defined cMET/HGFR-targeted Polymers as Gene Delivery Vehicles for the Theranostic Sodium Iodide Symporter (NIS) Gene.

    Science.gov (United States)

    Urnauer, Sarah; Morys, Stephan; Krhac Levacic, Ana; Müller, Andrea M; Schug, Christina; Schmohl, Kathrin A; Schwenk, Nathalie; Zach, Christian; Carlsen, Janette; Bartenstein, Peter; Wagner, Ernst; Spitzweg, Christine

    2016-08-01

    The sodium iodide symporter (NIS) as well-characterized theranostic gene represents an outstanding tool to target different cancer types allowing noninvasive imaging of functional NIS expression and therapeutic radioiodide application. Based on its overexpression on the surface of most cancer types, the cMET/hepatocyte growth factor receptor serves as ideal target for tumor-selective gene delivery. Sequence-defined polymers as nonviral gene delivery vehicles comprising polyethylene glycol (PEG) and cationic (oligoethanoamino) amide cores coupled with a cMET-binding peptide (cMBP2) were complexed with NIS-DNA and tested for receptor-specificity, transduction efficiency, and therapeutic efficacy in hepatocellular cancer cells HuH7. In vitro iodide uptake studies demonstrated high transduction efficiency and cMET-specificity of NIS-encoding polyplexes (cMBP2-PEG-Stp/NIS) compared to polyplexes without targeting ligand (Ala-PEG-Stp/NIS) and without coding DNA (cMBP2-PEG-Stp/Antisense-NIS). Tumor recruitment and vector biodistribution were investigated in vivo in a subcutaneous xenograft mouse model showing high tumor-selective iodide accumulation in cMBP2-PEG-Stp/NIS-treated mice (6.6 ± 1.6% ID/g (123)I, biological half-life 3 hours) by (123)I-scintigraphy. Therapy studies with three cycles of polyplexes and (131)I application resulted in significant delay in tumor growth and prolonged survival. These data demonstrate the enormous potential of cMET-targeted sequence-defined polymers combined with the unique theranostic function of NIS allowing for optimized transfection efficiency while eliminating toxicity.

  10. The new C-C bond formation in the reaction of o-amidophenolate indium(III) complex with alkyl iodides.

    Science.gov (United States)

    Piskunov, Alexandr V; Meshcheryakova, Irina N; Fukin, Georgy K; Shavyrin, Andrei S; Cherkasov, Vladimir K; Abakumov, Gleb A

    2013-08-07

    The reaction of bis(4,6-di-tert-butyl-N-(2,6-di-iso-propylphenyl)-o-amidophenolato)indium(III) anion with alkyl iodides is reported. This process includes oxidative addition of two RI (R = Me, Et) molecules to the non-transition metal complex and results in an alkyl transfer to ring carbon atoms with the formation of two new C-C bonds. The interaction proceeds at mild conditions and gives new indium(III) derivatives containing iminocyclohexa-1,4-dienolate type ligands.

  11. Investigation of Mechanisms of Enhanced Open-Circuit Photovoltage of Dye-Sensitized Solar Cells Based the Electrolyte Containing 1-Hexyl-3-Methylimidazolium Iodide

    Institute of Scientific and Technical Information of China (English)

    WANG Miao; ZHANG Qing-Li; WENG Yu-Xiang; LIN Yuan; XIAO Xu-Rui

    2006-01-01

    @@ The open-circuit photovoltage is improved by adding 1-hexyl-3-methylimidazolium iodide (HMImI) into the electrolyte. To investigate the mechanisms of the increase of the open-circuit photovoltage, we take the Mott Schottky analysis and time-resolved mid-infrared absorption spectroscopy to study the band edge movement of TiO2 and the rate of back electron transfer, respectively. The results indicate that the negative shift of the conduction band of TiO2 is a predominant factor to increase the open-circuit photovoltage for the electrolyte containing HMImL

  12. Catalytic titrations of silver(I) applying the iodide-catalysed manganese(IV)-arsenic(III) indicator reaction in the presence of sulphuric acid

    OpenAIRE

    TIBOR J. PASTOR; VOJKA V. ANTONIJEVIC; FERENC T. PASTOR

    1999-01-01

    A new catalytic potentiometric titration method for the determination of silver(I), applying the iodide-catalysed manganese(IV)-arsenic(III) indicator reaction in the presence of sulphuric acid, has been developed. The effect of the concentration of sulphuric acid and different ions, and of the mole ratio of manganese(IV) to arsenic(III) in the titrated solution, as well as of the titrand temperature on the conditions for the determination of silver(I) in solutions of various concentrations, ...

  13. Genes and environment as predisposing factors in autoimmunity: acceleration of spontaneous thyroiditis by dietary iodide in NOD.H2(h4) mice.

    Science.gov (United States)

    Kolypetri, Panayota; King, Justin; Larijani, Mani; Carayanniotis, George

    2015-01-01

    In the field of autoimmune thyroiditis, NOD.H2(h4) mice have attracted significant and increasing attention since they not only develop spontaneous disease but they present thyroiditis with accelerated incidence and severity if they ingest iodide through their drinking water. This animal model highlights the interplay between genetic and dietary factors in the triggering of autoimmune disease and offers new opportunities to study immunoregulatory parameters influenced by both genes and environment. Here, we review experimental findings with this mouse model of thyroiditis.

  14. 8a-Methyl-5,6,8,8a,9,10-hexahydro-10,12a-epoxyisoindolo[1,2-a]isoquinolinium iodide

    Directory of Open Access Journals (Sweden)

    Flavien A. A. Toze

    2010-06-01

    Full Text Available The title compound, C17H18NO+·I−, is an adduct resulting from an intramolecular Diels–Alder reaction of methallyl chloride with 3,4-dihydro-1-furylisoquinoline. The cation comprises a fused pentacyclic system containing three five-membered rings (dihydropyrrole, dihydrofuran and tetrahydrofuran and two six-membered rings (tetrahydropyridine and benzene. The five-membered rings have the usual envelope conformations, and the central six-membered tetrahydropyridine ring adopts the unsymmetrical half-boat conformation. In the crystal, cations and iodide anions are bound by weak intermolecular hydrogen-bonding interactions into a three-dimensional framework.

  15. (2S,7S-10-Ethyl-1,8,10,12-tetraazatetracyclo[8.3.1.18,12.02,7]pentadecan-10-ium iodide

    Directory of Open Access Journals (Sweden)

    Augusto Rivera

    2012-10-01

    Full Text Available The title chiral quaternary ammonium salt, C13H25N4+·I−, was synthesized through the Menschutkin reaction between the cage aminal (2S,7S-1,8,10,12-tetraazatetracyclo[8.3.1.18,12.02,7]pentadecane and ethyl iodide. The quaternization occurred regioselectively on the nitrogen with major sp3 character. The crystal structure consists of anions and cations separated by normal distances. Ions are not linked through C—H...I hydrogen bonds.

  16. Nanowires of methylammonium lead iodide (CH3NH3PbI3) prepared by low temperature solution-mediated crystallization.

    Science.gov (United States)

    Horváth, Endre; Spina, Massimo; Szekrényes, Zsolt; Kamarás, Katalin; Gaal, Richard; Gachet, David; Forró, László

    2014-12-10

    We report the synthesis of Methylammonium Lead Iodide (CH(3)NH(3)PbI(3)) nanowires by a low temperature solution processed crystallization using a simple slip-coating method. The anisotropic particle shape exhibits advantages over nanoparticles in terms of charge transport under illumination. These results provide a basis for solvent-mediated tailoring of structural properties like the crystallite size and orientation in trihalide perovskite thin films, which, once implemented into a device, may ultimately result in an enhanced charge carrier extraction.

  17. Photoinduced triplet-state electron transfer of platinum porphyrin: A one-step direct method for sensing iodide with an unprecedented detection limit

    KAUST Repository

    Masih, Dilshad

    2014-02-05

    Here, we report for the first time a one-step direct method for sensing halides in aqueous solution using phosphorescence quenching of platinum-cationic porphyrin. This method offers an easy, rapid, environmentally friendly, ultra-sensitive (with a previously unattained detection limit of 1 × 10-12 M) and economical method for the determination of iodide. To fully understand the reaction mechanism responsible for the phosphorescence quenching process, we have employed cutting-edge time-resolved laser spectroscopy with broadband capabilities. This journal is © The Royal Society of Chemistry 2015.

  18. Photoinduced triplet-state electron transfer of platinum porphyrin: a one-step direct method for sensing iodide with an unprecedented detection limit

    KAUST Repository

    Masih, Dilshad

    2015-02-05

    Here, we report for the first time a one-step direct method for sensing halides in aqueous solution using phosphorescence quenching of platinum-cationic porphyrin. This method offers an easy, rapid, environmentally friendly, ultra-sensitive (with a previously unattained detection limit of 1 × 10−12 M) and economical method for the determination of iodide. To fully understand the reaction mechanism responsible for the phosphorescence quenching process, we have employed cutting-edge time-resolved laser spectroscopy with broadband capabilities.

  19. Efficiency of Local Antiseptic Alkosol (Ethanol, Isopropanol-30g and Ortophenilphenol) and Povidone Iodide on the Incidence Of Surgical Site Infection After Inguinal Hernioplasty

    Science.gov (United States)

    Djozic, Harun; Pandza, Haris; Hasukic, Sefik; Custovic, Samir; Pandza, Berina; Krupalija, Amina; Beciragic, Edin

    2016-01-01

    Background: The risk of wound infection after elective inguinal hernia repair depends on several factors. One of the most important factors is the preoperative skin preparation. The use of antisepsis is performed to reduce the risk of surgical site infections (SSIs) and to remove causing organisms. This work compares two different agent forms for preoperative skin preparation to prevent SSIs. Objectives: The objective of the study is comparing the effects of two different agents used for preoperative skin preparation and prevention of SSIs. Material and methods: 100 adult patients were divided and randomized into two groups, each containing 50 patients. Both groups included patients that are scheduled for elective Lichtenstein inguinal hernia repair. The first group includes patients whose skin preparations were done with povidone iodine (PI) only. The second group included patients that are treated with two antiseptics; Alkosol (96% ethanol, isopropanol-30g and ortophenilphenol-0.1g) and povidone iodide. Alkosol is applied before the induction of anesthesia. The povidone iodide is applied after Alkosol has evaporated. The presence of bacterial growth in the wound was determined 24 and 48 hours after operation. Swabs were used to take samples, which were then cultivated to check for bacterial growth. The presence of infection was also determined by the following criteria: pain or tenderness, induration, erythema, local warmth of the wound etc. Results: The surgeon or clinician declared that after 24 hours the wound was infected in 20 patients in the control group and in 22 patients after 48 hours. In the Alkosol (96% ethanol, isopropanol-30g and ortophenilphenol-0.1g) and povidone iodide group infection was declared in only 3 patients after 24 hours. Discussion: Compared to the use of providone only, the use of Alkosol (96% ethanol, isopropanol-30g and ortophenilphenol-0.1g) and povidone iodide has many advantages and was associated with lower rates of SSIs

  20. Imaging characteristics, tissue distribution, and spread of a novel oncolytic vaccinia virus carrying the human sodium iodide symporter.

    Directory of Open Access Journals (Sweden)

    Dana Haddad

    Full Text Available INTRODUCTION: Oncolytic viruses show promise for treating cancer. However, to assess therapy and potential toxicity, a noninvasive imaging modality is needed. This study aims to determine the in vivo biodistribution, and imaging and timing characteristics of a vaccinia virus, GLV-1h153, encoding the human sodium iodide symporter (hNIS. METHODS: GLV-1h153 was modified from GLV-1h68 to encode the hNIS gene. Timing of cellular uptake of radioiodide (131I in human pancreatic carcinoma cells PANC-1 was assessed using radiouptake assays. Viral biodistribution was determined in nude mice bearing PANC-1 xenografts, and infection in tumors confirmed histologically and optically via Green Fluorescent Protein (GFP and bioluminescence. Timing characteristics of enhanced radiouptake in xenografts were assessed via (124I-positron emission tomography (PET. Detection of systemic administration of virus was investigated with both (124I-PET and 99m-technecium gamma-scintigraphy. RESULTS: GLV-1h153 successfully facilitated time-dependent intracellular uptake of (131I in PANC-1 cells with a maximum uptake at 24 hours postinfection (P<0.05. In vivo, biodistribution profiles revealed persistence of virus in tumors 5 weeks postinjection at 10(9 plaque-forming unit (PFU/gm tissue, with the virus mainly cleared from all other major organs. Tumor infection by GLV-1h153 was confirmed via optical imaging and histology. GLV-1h153 facilitated imaging virus replication in tumors via PET even at 8 hours post radiotracer injection, with a mean %ID/gm of 3.82 ± 0.46 (P<0.05 2 days after intratumoral administration of virus, confirmed via tissue radiouptake assays. One week post systemic administration, GLV-1h153-infected tumors were detected via (124I-PET and 99m-technecium-scintigraphy. CONCLUSION: GLV-1h153 is a promising oncolytic agent against pancreatic cancer with a promising biosafety profile. GLV-1h153 facilitated time-dependent hNIS-specific radiouptake in pancreatic