WorldWideScience

Sample records for californium chlorides

  1. Californium Electrodepositions at Oak Ridge National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Boll, Rose Ann [ORNL

    2015-01-01

    Electrodepositions of californium isotopes were successfully performed at Oak Ridge National Laboratory (ORNL) during the past year involving two different types of deposition solutions, ammonium acetate (NH4C2H3O2) and isobutanol ((CH3)2CHCH2OH). A californium product that was decay enriched in 251Cf was recovered for use in super-heavy element (SHE) research. This neutron-rich isotope, 251Cf, provides target material for SHE research for the potential discovery of heavier isotopes of Z=118. The californium material was recovered from aged 252Cf neutron sources in storage at ORNL. These sources have decayed for over 30 years, thus providing material with a very high 251Cf-to-252Cf ratio. After the source capsules were opened, the californium was purified and then electrodeposited using the isobutanol method onto thin titanium foils for use in an accelerator at the Joint Institute for Nuclear Research in Dubna, Russia. Another deposition method, ammonium acetate, was used to produce a deposition containing 1.7 0.1 Ci of 252Cf onto a stainless steel substrate. This was the largest single electrodeposition of 252Cf ever prepared. The 252Cf material was initially purified using traditional ion exchange media, such as AG50-AHIB and AG50-HCl, and further purified using a TEVA-NH4SCN system to remove any lanthanides, resulting in the recovery of 3.6 0.1 mg of purified 252Cf. The ammonium acetate deposition was run with a current of 1.0 amp, resulting in a 91.5% deposition yield. Purification and handling of the highly radioactive californium material created additional challenges in the production of these sources.

  2. Historical Review of Californium-252 Discovery and Development

    Science.gov (United States)

    Stoddard, D. H.

    1985-01-01

    This paper discusses the discovery and history of californium 252. This isotope may be synthesized by irradiating plutonium 239, plutonium 242, americium 243, or curium 244 with neutrons in a nuclear reactor. Various experiments and inventions involving Cf conducted at the Savannah River Plant are discussed. The evolution of radiotherapy using californium 252 is reviewed. (PLG)

  3. Production, Distribution, and Applications of Californium-252 Neutron Sources

    Energy Technology Data Exchange (ETDEWEB)

    Balo, P.A.; Knauer, J.B.; Martin, R.C.

    1999-10-03

    The radioisotope {sup 252}Cf is routinely encapsulated into compact, portable, intense neutron sources with a 2.6-year half-life. A source the size of a person's little finger can emit up to 10{sup 11} neutrons/s. Californium-252 is used commercially as a reliable, cost-effective neutron source for prompt gamma neutron activation analysis (PGNAA) of coal, cement, and minerals, as well as for detection and identification of explosives, laud mines, and unexploded military ordnance. Other uses are neutron radiography, nuclear waste assays, reactor start-up sources, calibration standards, and cancer therapy. The inherent safety of source encapsulations is demonstrated by 30 years of experience and by U.S. Bureau of Mines tests of source survivability during explosions. The production and distribution center for the U. S Department of Energy (DOE) Californium Program is the Radiochemical Engineering Development Center (REDC) at Oak Ridge National Laboratory (ORNL). DOE sells The radioisotope {sup 252}Cf is routinely encapsulated into compact, portable, intense neutron sources with a 2.6- year half-life. A source the size of a person's little finger can emit up to 10 neutrons/s. Californium-252 is used commercially as a reliable, cost-effective neutron source for prompt gamma neutron activation analysis (PGNAA) of coal, cement, and minerals, as well as for detection and identification of explosives, laud mines, and unexploded military ordnance. Other uses are neutron radiography, nuclear waste assays, reactor start-up sources, calibration standards, and cancer therapy. The inherent safety of source encapsulations is demonstrated by 30 years of experience and by U.S. Bureau of Mines tests of source survivability during explosions. The production and distribution center for the U. S Department of Energy (DOE) Californium Program is the Radiochemical Engineering Development Center (REDC) at Oak Ridge National Laboratory(ORNL). DOE sells {sup 252}Cf to commercial

  4. Teratogenic effect of Californium-252 irradiation in rats

    Energy Technology Data Exchange (ETDEWEB)

    Satow, Yukio; Lee, Juing-Yi; Hori, Hiroshi; Okuda, Hiroe; Tsuchimoto, Shigeo; Sawada, Shozo; Yokoro, Kenjiro (Hiroshima Univ. (Japan). Research Inst. for Nuclear Medicine and Biology)

    1989-06-01

    The teratogenicity of Californium-252 (Cf-252) irradiation which generates approximately 70% 2.3 MeV fast neutron and 30% gamma rays was evaluated. A single whole body exposure of Cf-252 at various doses was given to pregnant rats on day 8 or 9 of pregnancy, followed by microscopic autopsy of the fetuses at the terminal stage of pregnancy to search for external and internal malformations. For comparison, pregnant rats were irradiated with various doses of Cobalt-60 (Co-60) standard gamma rays at the same dose rate (1 rad/min.). The doses were 20-120 rad of Cf-252 and 80-220 rad of Co-60. Using frequency of radiation induced malformations observed on day 8 of pregnancy as an index, relative biological effectiveness (RBE) of 2.3-2.7 was obtained from the straight line obtained by modifying by the least squares method the frequency curves of malformed fetuses in total implants and in surviving fetuses. The types of malformations induced by Cf-252 and Co-60 irradiation were alike. Using fetal LD/sub 50/ as an index, 2.4 was obtained as RBE when irradiated on day 8 of pregnancy and 3.1 as that when irradiated on day 9. The results showed that Cf-252 had stronger a teratogenic effect than Co-60 gamma rays. (author).

  5. Apparatus for the measurement of total body nitrogen using prompt neutron activation analysis with californium-252.

    Science.gov (United States)

    Mackie, A; Hannan, W J; Smith, M A; Tothill, P

    1988-01-01

    Details of clinical apparatus designed for the measurement of total body nitrogen (as an indicator of body protein), suitable for the critically ill, intensive-care patient are presented. Californium-252 radio-isotopic neutron sources are used, enabling a nitrogen measurement by prompt neutron activation analysis to be made in 40 min with a precision of +/- 3.2% for a whole body dose equivalent of 0.145 mSv. The advantages of Californium-252 over alternative neutron sources are discussed. A comparison between two irradiation/detection geometries is made, leading to an explanation of the geometry adopted for the apparatus. The choice of construction and shielding materials to reduce the count rate at the detectors and consequently to reduce the pile-up contribution to the nitrogen background is discussed. Salient features of the gamma ray spectroscopy system to reduce spectral distortion from pulse pile-up are presented.

  6. Spontaneous Partitioning of Californium from Curium: Curious Cases from the Crystallization of Curium Coordination Complexes

    Energy Technology Data Exchange (ETDEWEB)

    Cary, Samantha K.; Silver, Mark A.; Liu, Guokui; Wang, Jamie C.; Bogart, Justin A.; Stritzinger, Jared T.; Arico, Alexandra A.; Hanson, Kenneth; Schelter, Eric J.; Albrecht-Schmitt, Thomas E.

    2015-12-07

    The reaction of 248CmCl3 with excess 2,6-pyridinedicarboxylic acid (DPA) under mild solvothermal conditions results in crystallization of the tris-chelate complex Cm(HDPA)3·H2O. Approximately half of the curium remains in solution at the end of this process, and evaporation of the mother liquor results in crystallization of the bis-chelate complex [Cm(HDPA)- (H2DPA)(H2O)2Cl]Cl·2H2O. 248Cm is the daughter of the α decay of 252Cf and is extracted in high purity from this parent. However, trace amounts of 249,250,251Cf are still present in all samples of 248Cm. During the crystallization of Cm(HDPA)3·H2O and [Cm(HDPA)(H2DPA)(H2O)2Cl]Cl·2H2O, californium(III) spontaneously separates itself from the curium complexes and is found doped within crystals of DPA in the form of Cf(HDPA)3. These results add to the growing body of evidence that the chemistry of californium is fundamentally different from that of earlier actinides.

  7. Chloride transference during electrochemical chloride extraction process

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Chemical titration method and lab-made chloride probes were jointly adopted to investigate the effects of water-to-cement (W/C) ratio and the impressed current density on chloride transport for cement-based materials during electrochemical chloride extraction (ECE) process.The dissolution of bound chlorides and the effect of current density on dissolution were analyzed.The variations of chloride concentration at different depths and the chloride transference process were monitored.Test results show that W/C ratios adopted have slight influence on chloride extraction,while chloride extraction efficiency is mainly determined by the impressed current density.During ECE process a portion of bound chloride ions dissolved and the amount of bound chlorides released is directly proportional to current density.

  8. Clinical Report on Californium-252 Neutron Intraluminal Brachytherapy Combined with External Irradiation for Cervical Carcinoma Treatment

    Institute of Scientific and Technical Information of China (English)

    Huanyu Zhao; Keming Wang; Jian Sun; Xin Geng; Weiming Zhang

    2006-01-01

    OBJECTIVE To observe the curative effects and complications of californium-252 (252Cf) neutron intraluminal brachytherapy (IBT) combined with external irradiation (El) for treatment of cervical carcinoma.METHODS From December 2000 to December 2004, 128 cases of cervical carcinoma staged into ⅡA~ⅢB according to the International Federation of Gynecology and Obstetrics (FIGO) standards were treated with 252Cf neutron IBT using 8~10 Gy per fraction, once a week. The total dose at reference A point was 36~40 Gy in 4~5 fractions. From the second day after 252Cf neutron IBT treatment, the whole pelvic cavity was treated with 60Co γ-ray El, applying 2 Gy per fraction, 4 times per week. After 20~25 Gy of El, the center of the whole pelvic field was blocked with 4 cm of lead in width. The total dose of El was 45~50 Gy.RESULTS The short-term therapeutic effects were CR 95.3% and PR 4.7%. The 3 and 5-year local control rates were 93.5% and 87.9%. The overall 3-year survival rate was 87.5% and for Stages Ⅱ and Ⅲ , 90.9%and 81.5% respectively; the overall 5-year survival rate was 70% and for Stages Ⅱ and Ⅲ, 76.2% and 61% respectively. The rate of radiation complications was 4.7% for radiation cystitis, 7.8% for radiation proctitis, 6.3%for vagina contracture and adhesion and 5.5% for protracted radiation proctitis.CONCLUSION An combination of 252Cf neutron IBT with El for treatment of cervical carcinoma can be well-tolerated by cervical carcinoma patients. The rate of local tumor control is high and radiation complications are few.

  9. Application of TSH bioindicator for studying the biological efficiency of neutrons from californium-252 source

    Energy Technology Data Exchange (ETDEWEB)

    Cebulska-Wasilewska, A.; Rekas, K. [Institute of Nuclear Physics, Cracow (Poland); Kim, J.K. [Korea Atomic Energy Research Inst., Taejon (Korea, Republic of)

    1997-12-31

    The effectiveness of neutrons from a Californium-252 source in the induction of various abnormalities in the Tradescantia clone 4430 stamen hair cells (TSH-assay) was studied. The special attention was paid to check whether any enhancement in effects caused by process of boron neutron capture is visible in the cells enriched with boron ions. Two chemicals (borax and BSH) were applied to introduce boron-10 ions into cells. Inflorescence, normal or pretreated with chemicals containing boron, were irradiated in the air with neutrons from a Cf-252 source at KAERI, Taejon, Korea. To estimate the relative biological effectiveness (RBE) in the induction of gene mutations of the neutron beam under the study, Tradescantia inflorescences, without any chemical pretreatment, were irradiated with various doses of X-rays. The ranges of radiation doses used were 0-0.1 Gy in neutrons and 0-0.5 Gy in X-rays. After the time needed to complete the postirradiation repair Tradescantia cuttings were transferred to Cracow, where screening of gene and lethal; mutations, cell cycle alterations in somatic cells have been done, and dose response relationships were figured. The maximal RBE values were estimated in the range of 4.6-6.8. Alterations of RBE value were observed; from 6.8 to 7.8 in the case of plants pretreated with 240 ppm of B-10 from borax, and 4.6 to 6.1 in the case of 400 ppm of B-10 from BSH. Results showed a slight, although statistically insignificant increase in biological efficacy of radiation from the Cf-252 source in samples pretreated with boron containing chemicals. (author)

  10. Tribenzylammonium chloride

    Directory of Open Access Journals (Sweden)

    Waly Diallo

    2014-05-01

    Full Text Available Single crystals of the title salt, C21H21NH+·Cl−, were isolated as a side product from the reaction involving [(C6H5CH23NH]2[HPO4] and Sn(CH33Cl in ethanol. Both the cation and the anion are situated on a threefold rotation axis. The central N atom in the cation has a slightly distorted tetrahedral environment, with angles ranging from 107.7 to 111.16 (10°. In the crystal, the tribenzylammonium cations and chloride anions are linked through N—H...Cl and C—H...Cl hydrogen bonds, leading to the formation of infinite chains along [001]. The crystal studied was a merohedral twin.

  11. Study of the shielding for spontaneous fission sources of Californium-252; Estudio de blindaje para fuentes de fision espontanea de Californio-252

    Energy Technology Data Exchange (ETDEWEB)

    Davila R, I

    1991-06-15

    A shielding study is made to attenuate, until maximum permissible levels, the neutrons radiation and photons emitted by spontaneous fission coming from a source of Californium-252. The compound package by a database (Library DLC-23) and the ANISNW code is used, in it version for personal computer. (Author)

  12. Long-term effects of an intracavitary treatment with californium-252 on normal tissue. [Swine, /sup 226/Ra

    Energy Technology Data Exchange (ETDEWEB)

    Sullivan, M.F.; Beamer, J.L.; Mahony, T.D.; Cross, F.T.; Lund, J.E.; Endres, G.W.R.

    1976-01-01

    About one hundred fifty swine were exposed to either radium-226 or californium-252 sources in the uterine cervix to determine an RBE for both acute and long-term effects. That value for early changes in the tissues at risk in the treatment of cervical cancer was between 6.2 and 6.8. The incidence of complications increased with time after exposure, especially among animals treated with /sup 252/Cf. Analysis of rectal injury showed that ulceration occurred frequently within a year postexposure at doses between 1600 and 2400 rad calculated at 2 cm lateral to the source midline. Fat necrosis and smooth muscle atrophy, resulting in a local rectal stricture, were delayed changes observed in some animals. The lower ureter was the site for a greater frequency of complications than the GI tract. Ureteral stricture often occurred at doses of 1200 rad from /sup 252/Cf and 7000 rad from /sup 226/Ra. Observation of delayed effects in the uterine-cervix in animals held up to 4 years postexposure indicate that the RBE for /sup 252/Cf may be increased to a value as high as 18, while repair may have even decreased it to about 5.6 in the rectum. Fifty swine are still being observed for long-term effects after doses above 800 rad from /sup 252/Cf and 5000 rad from /sup 226/Ra.

  13. Development of electron beam ion source charge breeder for rare isotopes at Californium Rare Isotope Breeder Upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Kondrashev, S.; Dickerson, C.; Levand, A.; Ostroumov, P. N.; Pardo, R. C.; Savard, G.; Vondrasek, R. [Physics Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Alessi, J.; Beebe, E.; Pikin, A. [Collider-Accelerator Department, Brookhaven National Laboratory, Upton, New York 11973 (United States); Kuznetsov, G. I.; Batazova, M. A. [Budker Institute of Nuclear Physics, Novosibirsk 630090 (Russian Federation)

    2012-02-15

    Recently, the Californium Rare Isotope Breeder Upgrade (CARIBU) to the Argonne Tandem Linac Accelerator System (ATLAS) was commissioned and became available for production of rare isotopes. Currently, an electron cyclotron resonance ion source is used as a charge breeder for CARIBU beams. To further increase the intensity and improve the purity of neutron-rich ion beams accelerated by ATLAS, we are developing a high-efficiency charge breeder for CARIBU based on an electron beam ion source (EBIS). The CARIBU EBIS charge breeder will utilize the state-of-the-art EBIS technology recently developed at Brookhaven National Laboratory (BNL). The electron beam current density in the CARIBU EBIS trap will be significantly higher than that in existing operational charge-state breeders based on the EBIS concept. The design of the CARIBU EBIS charge breeder is nearly complete. Long-lead components of the EBIS such as a 6-T superconducting solenoid and an electron gun have been ordered with the delivery schedule in the fall of 2011. Measurements of expected breeding efficiency using the BNL Test EBIS have been performed using a Cs{sup +} surface ionization ion source for external injection in pulsed mode. In these experiments we have achieved {approx}70% injection/extraction efficiency and breeding efficiency into the most abundant charge state of {approx}17%.

  14. Development of electron beam ion source charge breeder for rare isotopes at Californium Rare Isotope Breeder Upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Kondrashev S.; Alessi J.; Dickerson, C.; Levand, A.; Ostroumov, P.N.; Pardo, R.C.; Savard, G.; Vondrasek, R.; Beebe, E.; Pikin, A.; Kuznetsov, G.I.; Batazova, M.A.

    2012-02-03

    Recently, the Californium Rare Isotope Breeder Upgrade (CARIBU) to the Argonne Tandem Linac Accelerator System (ATLAS) was commissioned and became available for production of rare isotopes. Currently, an electron cyclotron resonance ion source is used as a charge breeder for CARIBU beams. To further increase the intensity and improve the purity of neutron-rich ion beams accelerated by ATLAS, we are developing a high-efficiency charge breeder for CARIBU based on an electron beam ion source (EBIS). The CARIBU EBIS charge breeder will utilize the state-of-the-art EBIS technology recently developed at Brookhaven National Laboratory (BNL). The electron beam current density in the CARIBU EBIS trap will be significantly higher than that in existing operational charge-state breeders based on the EBIS concept. The design of the CARIBU EBIS charge breeder is nearly complete. Long-lead components of the EBIS such as a 6-T superconducting solenoid and an electron gun have been ordered with the delivery schedule in the fall of 2011. Measurements of expected breeding efficiency using the BNL Test EBIS have been performed using a Cs{sup +} surface ionization ion source for external injection in pulsed mode. In these experiments we have achieved {approx}70% injection/extraction efficiency and breeding efficiency into the most abundant charge state of {approx}17%.

  15. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents the state-of-the art: an analytical model which describes chloride profiles in concrete as function of depth...... makes physical sense for the design engineer, i.e. the achieved chloride diffusion coefficients at 1 year and 100 years, D1 and D100 respectively, and the corresponding achieved chloride concentrations at the exposed concrete surface, C1 and C100. Data from field exposure supports the assumption of time...... dependent surface chloride concentrations and the diffusion coefficients. Model parameters for Portland cement concretes with and without silica fume and fly ash in marine atmospheric and submerged South Scandinavian environment are suggested in a companion paper based on 10 years field exposure data....

  16. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents experimentally based design parameters for Portland cement concretes with and without silica fume and fly ash...... in marine atmospheric and submersed South Scandinavian environment. The design parameters are based on sequential measurements of 86 chloride profiles taken over ten years from 13 different types of concrete. The design parameters provide the input for an analytical model for chloride profiles as function...

  17. Lithium Sulfuryl Chloride Battery.

    Science.gov (United States)

    Primary batteries , Electrochemistry, Ionic current, Electrolytes, Cathodes(Electrolytic cell), Anodes(Electrolytic cell), Thionyl chloride ...Phosphorus compounds, Electrical conductivity, Calibration, Solutions(Mixtures), Electrical resistance, Performance tests, Solvents, Lithium compounds

  18. Benzalkonium Chloride and Glaucoma

    OpenAIRE

    Rasmussen, Carol A.; Kaufman, Paul L.; Kiland, Julie A.

    2014-01-01

    Glaucoma patients routinely take multiple medications, with multiple daily doses, for years or even decades. Benzalkonium chloride (BAK) is the most common preservative in glaucoma medications. BAK has been detected in the trabecular meshwork (TM), corneal endothelium, lens, and retina after topical drop installation and may accumulate in those tissues. There is evidence that BAK causes corneal and conjunctival toxicity, including cell loss, disruption of tight junctions, apoptosis and preapo...

  19. Oxomemazine hydro-chloride.

    Science.gov (United States)

    Siddegowda, M S; Butcher, Ray J; Akkurt, Mehmet; Yathirajan, H S; Ramesh, A R

    2011-08-01

    IN THE TITLE COMPOUND [SYSTEMATIC NAME: 3-(5,5-dioxo-phen-othia-zin-10-yl)-N,N,2-trimethyl-propanaminium chloride], C(18)H(23)N(2)O(2)S(+)·Cl(-), the dihedral angle between the two outer aromatic rings of the phenothia-zine unit is 30.5 (2)°. In the crystal, the components are linked by N-H⋯Cl and C-H⋯Cl hydrogen bonds and C-H⋯π inter-actions.

  20. Benzalkonium chloride and glaucoma.

    Science.gov (United States)

    Rasmussen, Carol A; Kaufman, Paul L; Kiland, Julie A

    2014-01-01

    Glaucoma patients routinely take multiple medications, with multiple daily doses, for years or even decades. Benzalkonium chloride (BAK) is the most common preservative in glaucoma medications. BAK has been detected in the trabecular meshwork (TM), corneal endothelium, lens, and retina after topical drop installation and may accumulate in those tissues. There is evidence that BAK causes corneal and conjunctival toxicity, including cell loss, disruption of tight junctions, apoptosis and preapoptosis, cytoskeleton changes, and immunoinflammatory reactions. These same effects have been reported in cultured human TM cells exposed to concentrations of BAK found in common glaucoma drugs and in the TM of primary open-angle glaucoma donor eyes. It is possible that a relationship exists between chronic exposure to BAK and glaucoma. The hypothesis that BAK causes/worsens glaucoma is being tested experimentally in an animal model that closely reflects human physiology.

  1. Chloride on the Move

    KAUST Repository

    Li, Bo

    2017-01-09

    Chloride (Cl−) is an essential plant nutrient but under saline conditions it can accumulate to toxic levels in leaves; limiting this accumulation improves the salt tolerance of some crops. The rate-limiting step for this process – the transfer of Cl− from root symplast to xylem apoplast, which can antagonize delivery of the macronutrient nitrate (NO3−) to shoots – is regulated by abscisic acid (ABA) and is multigenic. Until recently the molecular mechanisms underpinning this salt-tolerance trait were poorly defined. We discuss here how recent advances highlight the role of newly identified transport proteins, some that directly transfer Cl− into the xylem, and others that act on endomembranes in ‘gatekeeper’ cell types in the root stele to control root-to-shoot delivery of Cl−.

  2. Studies Update Vinyl Chloride Hazards.

    Science.gov (United States)

    Rawls, Rebecca

    1980-01-01

    Extensive study affirms that vinyl chloride is a potent animal carcinogen. Epidemiological studies show elevated rates of human cancers in association with extended contact with the compound. (Author/RE)

  3. Parameters Affecting Hydrogen Chloride Measurements

    Science.gov (United States)

    1993-06-01

    contain sea salt, which is hygroscopic because of the magnesium chloride present, or ammonium bisulfate , which mostly comes from sulfur pollution and is...boosters release hydrogen chloride as a combustion product, and hydrazines or nitric acid can be spilled from liquid fuel motors. Monitoring the...solubility constant, and the second is the acid ionization constant. From experimental work, the product of the two constants is well established (Reference

  4. Chloride channels in stroke

    Institute of Scientific and Technical Information of China (English)

    Ya-ping ZHANG; Hao ZHANG; Dayue Darrel DUAN

    2013-01-01

    Vascular remodeling of cerebral arterioles,including proliferation,migration,and apoptosis of vascular smooth muscle cells (VSMCs),is the major cause of changes in the cross-sectional area and diameter of the arteries and sudden interruption of blood flow or hemorrhage in the brain,ie,stroke.Accumulating evidence strongly supports an important role for chloride (Clˉ) channels in vascular remodeling and stroke.At least three Clˉ channel genes are expressed in VSMCs:1) the TMEM16A (or Ano1),which may encode the calcium-activated Clˉ channels (CACCs); 2) the CLC-3 Clˉ channel and Clˉ/H+ antiporter,which is closely related to the volume-regulated Clˉ channels (VRCCs); and 3) the cystic fibrosis transmembrane conductance regulator (CFTR),which encodes the PKA-and PKC-activated Clˉ channels.Activation of the CACCs by agonist-induced increase in intracellular Ca2+ causes membrane depolarization,vasoconstriction,and inhibition of VSMC proliferation.Activation of VRCCs by cell volume increase or membrane stretch promotes the production of reactive oxygen species,induces proliferation and inhibits apoptosis of VSMCs.Activation of CFTR inhibits oxidative stress and may prevent the development of hypertension.In addition,Clˉ current mediated by gammaaminobutyric acid (GABA) receptor has also been implicated a role in ischemic neuron death.This review focuses on the functional roles of Clˉ channels in the development of stroke and provides a perspective on the future directions for research and the potential to develop Clˉ channels as new targets for the prevention and treatment of stroke.

  5. 21 CFR 184.1138 - Ammonium chloride.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium chloride. 184.1138 Section 184.1138 Food... Specific Substances Affirmed as GRAS § 184.1138 Ammonium chloride. (a) Ammonium chloride (NH4Cl, CAS Reg. No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution....

  6. 46 CFR 151.50-34 - Vinyl chloride (vinyl chloride monomer).

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Vinyl chloride (vinyl chloride monomer). 151.50-34... chloride (vinyl chloride monomer). (a) Copper, aluminum, magnesium, mercury, silver, and their alloys shall... equipment that may come in contact with vinyl chloride liquid or vapor. (b) Valves, flanges, and...

  7. 40 CFR 61.65 - Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... dichloride, vinyl chloride and polyvinyl chloride plants. 61.65 Section 61.65 Protection of Environment... AIR POLLUTANTS National Emission Standard for Vinyl Chloride § 61.65 Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants. An owner or operator of an ethylene...

  8. Electrochemical Chloride extraction using external electrodes?

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Pedersen, Anne Juul

    2006-01-01

    Electrochemical methods for the removal of chloride from concrete have been developed and the methods are primarily designed for situations where corrosion has started due to an increased chloride concentration in the vicinity of the reinforcement. In these methods the reinforcement is used...... as the cathode. However, some unwanted side effects can occur, including alkali-silica reaction and in some cases hydrogen embrittlement. It is also suggested also to use electrochemical chloride extraction in a preventive way in constructions where chloride induced corrosion is likely to be a problem after...... a period of time, i.e. remove the chlorides before the chloride front reaches the reinforcement. If the chlorides are removed from outer few centimetres from the surface, the chloride will not reach the reinforcement and cause damage. By using the electrochemical chloride removal in this preventive way...

  9. Lubiprostone: a chloride channel activator.

    Science.gov (United States)

    Lacy, Brian E; Levy, L Campbell

    2007-04-01

    In January 2006 the Food and Drug Administration approved lubiprostone for the treatment of chronic constipation in men and women aged 18 and over. Lubiprostone is categorized as a prostone, a bicyclic fatty acid metabolite of prostaglandin E1. Lubiprostone activates a specific chloride channel (ClC-2) in the gastrointestinal (GI) tract to enhance intestinal fluid secretion, which increases GI transit and improves symptoms of constipation. This article reviews the role of chloride channels in the GI tract, describes the structure, function, and pharmacokinetics of lubiprostone, and discusses clinically important data on this new medication.

  10. [Headspace GC/MS analysis of residual vinyl chloride and vinylidene chloride in polyvinyl chloride and polyvinylidene chloride products].

    Science.gov (United States)

    Ohno, Hiroyuki; Mutsuga, Motoh; Kawamura, Yoko; Suzuki, Masako; Aoyama, Taiki

    2005-02-01

    A headspace GC/MS analysis method for the simultaneous determination of residual vinyl chloride (VC) and vinylidene chloride (VDC) in polyvinyl chloride (PVC) and polyvinylidene chloride (PVDC) products was developed. A test sample was swelled overnight with N,N-dimethylacetamide in a sealed vial. The vial was incubated for 1 hour at 90 degrees C, then the headspace gas was analyzed by GC/MS using a PLOT capillary column. The recoveries from spiked PVC and PVDC samples were 90.0-112.3% for VC and 85.2-108.3% for VDC. The determination limits were 0.01 microg/g for VC and 0.06/microg/g for VDC, respectively. By this method, VC was detected in two PVC water supply pipes at the levels of 0.61 and 0.01 microg/g. On the other hand, VC and VDC were not detected in any of the food container-packages or toys tested.

  11. 1,5-Diaminotetrazolium chloride

    Directory of Open Access Journals (Sweden)

    Ling-Qiao Meng

    2010-04-01

    Full Text Available The title compound, CH5N6+·Cl−, crystallized with two indepedent 1,5-diaminotetrazolium cations and two independent chloride anions in the asymmetric unit. In the crystal, there are a number of N—H...Cl hydrogen-bonding interactions, which generate a three-dimensional network.

  12. Chloride : The queen of electrolytes?

    NARCIS (Netherlands)

    Berend, Kenrick; van Hulsteijn, Leonard Hendrik; Gans, Rijk O. B.

    2012-01-01

    Background: Channelopathies, defined as diseases that are caused by mutations in genes encoding ion channels, are associated with a wide variety of symptoms and have been documented extensively over the past decade. In contrast, despite the important role of chloride in serum, textbooks in general d

  13. 21 CFR 173.375 - Cetylpyridinium chloride.

    Science.gov (United States)

    2010-04-01

    ... CONSUMPTION Specific Usage Additives § 173.375 Cetylpyridinium chloride. Cetylpyridinium chloride (CAS Reg. No... Nutrition's Library, Food and Drug Administration, 5100 Paint Branch Pkwy., College Park, MD 20740, or...

  14. Progress of Carbonation in Chloride Contaminated Concretes

    OpenAIRE

    Wang, Yaocheng; Basheer, P. A.M.; Nanukuttan, S; Bai, Y.

    2016-01-01

    Concretes used in marine environment are generally under the cyclic effect of CO2 and chloride ions (Cl-). To date, the influence of carbonation on ingress of chloride ions in concretes has been widely studied; in comparison, study on the influence of Cl- on the progress of carbonation is limited. During the study, concretes were exposed to independent and combined mechanisms of carbonation and chloride ingress regimes. Profiles of apparent pH and chloride concentration were used to indicate ...

  15. Microbial reductive dehalogenation of vinyl chloride

    Energy Technology Data Exchange (ETDEWEB)

    Spormann, Alfred M [Stanford, CA; Muller, Jochen A [Baltimore, MD; Rosner, Bettina M [Berlin, DE; Von Abendroth, Gregory [Mannheim, DE; Meshulam-Simon, Galit [Los Angeles, CA; McCarty, Perry L [Stanford, CA

    2014-02-11

    Compositions and methods are provided that relate to the bioremediation of chlorinated ethenes, particularly the bioremediation of vinyl chloride by Dehalococcoides-like organisms. An isolated strain of bacteria, Dehalococcoides sp. strain VS, that metabolizes vinyl chloride is provided; the genetic sequence of the enzyme responsible for vinyl chloride dehalogenation; methods of assessing the capability of endogenous organisms at an environmental site to metabolize vinyl chloride; and a method of using the strains of the invention for bioremediation.

  16. 21 CFR 184.1426 - Magnesium chloride.

    Science.gov (United States)

    2010-04-01

    ... mineral bischofite. It is prepared by dissolving magnesium oxide, hydroxide, or carbonate in aqueous... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Magnesium chloride. 184.1426 Section 184.1426 Food... Specific Substances Affirmed as GRAS § 184.1426 Magnesium chloride. (a) Magnesium chloride (MgC12·6H2O,...

  17. Cystic Fibrosis (CF): Chloride Sweat Test

    Science.gov (United States)

    ... Old Feeding Your 1- to 2-Year-Old Cystic Fibrosis (CF) Chloride Sweat Test KidsHealth > For Parents > Cystic Fibrosis (CF) Chloride Sweat Test Print A A A ... It Is A chloride sweat test helps diagnose cystic fibrosis (CF) , an inherited disorder that makes kids sick ...

  18. 75 FR 33824 - Barium Chloride From China

    Science.gov (United States)

    2010-06-15

    ... COMMISSION Barium Chloride From China Determination On the basis of the record\\1\\ developed in the subject... order on barium chloride from China would be likely to lead to continuation or recurrence of material... Barium Chloride from China: Investigation No. 731-TA-149 (Third Review). By order of the...

  19. 75 FR 19657 - Barium Chloride From China

    Science.gov (United States)

    2010-04-15

    ... COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Notice of... chloride from China. SUMMARY: The Commission hereby gives notice that it will proceed with a full review... revocation of the antidumping duty order on barium chloride from China would be likely to lead...

  20. 21 CFR 172.180 - Stannous chloride.

    Science.gov (United States)

    2010-04-01

    ... Preservatives § 172.180 Stannous chloride. The food additive stannous chloride may be safely used for color... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Stannous chloride. 172.180 Section 172.180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR...

  1. Oxomemazine hydro­chloride

    OpenAIRE

    Siddegowda, M. S.; Butcher, Ray J.; Mehmet Akkurt; Yathirajan, H.S.; Ramesh, A. R.

    2011-01-01

    In the title compound [systematic name: 3-(5,5-dioxophenothiazin-10-yl)-N,N,2-trimethylpropanaminium chloride], C18H23N2O2S+·Cl−, the dihedral angle between the two outer aromatic rings of the phenothiazine unit is 30.5 (2)°. In the crystal, the components are linked by N—H...Cl and C—H...Cl hydrogen bonds and C—H...π interactions.

  2. Shock compression of polyvinyl chloride

    Science.gov (United States)

    Neogi, Anupam; Mitra, Nilanjan

    2016-04-01

    This study presents shock compression simulation of atactic polyvinyl chloride (PVC) using ab-initio and classical molecular dynamics. The manuscript also identifies the limits of applicability of classical molecular dynamics based shock compression simulation for PVC. The mechanism of bond dissociation under shock loading and its progression is demonstrated in this manuscript using the density functional theory based molecular dynamics simulations. The rate of dissociation of different bonds at different shock velocities is also presented in this manuscript.

  3. Developing chloride resisting concrete using PFA

    Energy Technology Data Exchange (ETDEWEB)

    Dhir, R.K.; El-Mohr, M.A.K.; Dyer, T.D. [Univ. of Dundee (United Kingdom). Dept. of Civil Engineering

    1997-11-01

    PFA concrete mixes were designed to optimize resistance to chloride ingress. Chloride binding capacity, intrinsic permeability and their concomitant influence on the coefficient of chloride diffusion have been investigated. PFA replacements up to 67% and exposure concentrations of 0.1, 0.5, 1.0 and 5.0 mole/liter were used. Chloride binding capacity was found to increase with increasing PFA replacement up to 50% and to then decline. It increased with chloride exposure concentration as well as water/binder ratio. The coefficient of chloride diffusion of concrete samples was found to be dependent on both the intrinsic permeability of the concrete and the ability of its cement matrix to bind chlorides.

  4. Salt, chloride, bleach, and innate host defense.

    Science.gov (United States)

    Wang, Guoshun; Nauseef, William M

    2015-08-01

    Salt provides 2 life-essential elements: sodium and chlorine. Chloride, the ionic form of chlorine, derived exclusively from dietary absorption and constituting the most abundant anion in the human body, plays critical roles in many vital physiologic functions, from fluid retention and secretion to osmotic maintenance and pH balance. However, an often overlooked role of chloride is its function in innate host defense against infection. Chloride serves as a substrate for the generation of the potent microbicide chlorine bleach by stimulated neutrophils and also contributes to regulation of ionic homeostasis for optimal antimicrobial activity within phagosomes. An inadequate supply of chloride to phagocytes and their phagosomes, such as in CF disease and other chloride channel disorders, severely compromises host defense against infection. We provide an overview of the roles that chloride plays in normal innate immunity, highlighting specific links between defective chloride channel function and failures in host defense.

  5. Californium Recovery from Palladium Wire

    Energy Technology Data Exchange (ETDEWEB)

    Burns, Jon D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-08-01

    The recovery of 252Cf from palladium-252Cf cermet wires was investigated to determine the feasibility of implementing it into the cermet wire production operation at Oak Ridge National Laboratory’s Radiochemical Engineering Development Center. The dissolution of Pd wire in 8 M HNO3 and trace amounts of HCl was studied at both ambient and elevated temperatures. These studies showed that it took days to dissolve the wire at ambient temperature and only 2 hours at 60°C. Adjusting the ratio of the volume of solvent to the mass of the wire segment showed little change in the kinetics of dissolution, which ranged from 0.176 mL/mg down to 0.019 mL/mg. A successful chromatographic separation of 153Gd, a surrogate for 252Cf, from Pd was demonstrated using AG 50x8 cation exchange resin with a bed volume of 0.5 mL and an internal diameter of 0.8 cm.

  6. Hydrolysis of cupric chloride in aqueous ammoniacal ammonium chloride solutions

    Directory of Open Access Journals (Sweden)

    Limpo, J. L.

    1995-06-01

    Full Text Available Cupric solubility in the CuCl2-NH4Cl-NH3-H2O system for chloride concentrations lower than 4 molal in the temperature range 25-60 °C was studied. The experimental results show that for chloride concentration between 3.0 and 1.0 molal the cupric solubility is determined by the solubility of the cupric hydroxychloride Cu(OH1.5Cl0.5. For a chloride concentration value of 4.0 molal, there are two cupric compounds, the hydroxychloride Cu(OH1.5Cl0.5 or the diammine chloride Cu(NH32Cl2, on which the solubility of Cu(II depends, according to the temperature and the value of the ratio [NH3]Total/[Cu]Total.

    Se estudia la solubilidad del Cu(II en el sistema CuCl2-NH4Cl-NH3-H2O para concentraciones de cloruro inferiores a 4 molal en el intervalo de temperaturas 25-60 °C. Los resultados experimentales muestran que, para concentraciones de cloruros comprendidas entre 3,0 y 1,0 molal, la solubilidad cúprica viene determinada por la solubilidad del hidroxicloruro cúprico, Cu(OH1.5Cl0.5. Para concentraciones de cloruro 4,0 molal, existen dos compuestos cúpricos, el hidroxicloruro, Cu(OH1.5Cl0.5 o el cloruro de diamina, Cu(NH32Cl2, de los que, de acuerdo con la temperatura y con el valor de la relación [NH3]Total/[Cu]Total depende la solubilidad del Cu(II.

  7. Oxomemazine hydro­chloride

    Science.gov (United States)

    Siddegowda, M. S.; Butcher, Ray J.; Akkurt, Mehmet; Yathirajan, H. S.; Ramesh, A. R.

    2011-01-01

    In the title compound [systematic name: 3-(5,5-dioxo­phen­othia­zin-10-yl)-N,N,2-trimethyl­propanaminium chloride], C18H23N2O2S+·Cl−, the dihedral angle between the two outer aromatic rings of the phenothia­zine unit is 30.5 (2)°. In the crystal, the components are linked by N—H⋯Cl and C—H⋯Cl hydrogen bonds and C—H⋯π inter­actions. PMID:22090928

  8. Simple chloride sensors for continuous groundwater monitoring

    DEFF Research Database (Denmark)

    Thorn, Paul; Mortensen, John

    2012-01-01

    The development of chloride sensors which can be used for continuous, on-line monitoring of groundwater could be very valuable in the management of our coastal water resources. However, sensor stability, drift, and durability all need to be addressed in order for the sensors to be used...... in continuous application. This study looks at the development of a simple, inexpensive chloride electrode, and evaluates its performance under continuous use, both in the laboratory and in a field test in a monitoring well. The results from the study showed a consistent response to changing chloride...... sensor remained responsive even at low chloride concentrations, where the conductivity electrode was no longer responding to changing chloride levels. With the results, it is believed that the simple chloride sensor could be used for continuous monitoring of groundwater quality....

  9. Chloride Ion Critical Content in Reinforced Concrete

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Chloride ion critical content was studied under soaking and cycle of dry and wet conditions,with three electrochemical nondestructive measuring techniques, i e, half-cell potential, A C impedance, and time potential. The experimental results show that chloride ion critical content is primarily determined by the water cement ratio, while for the same concrete mixture the chloride ion critical content in soaking conditions is larger than that in a cycle of dry and wet conditions.

  10. Chloride binding site of neurotransmitter sodium symporters

    DEFF Research Database (Denmark)

    Kantcheva, Adriana Krassimirova; Quick, Matthias; Shi, Lei

    2013-01-01

    Neurotransmitter:sodium symporters (NSSs) play a critical role in signaling by reuptake of neurotransmitters. Eukaryotic NSSs are chloride-dependent, whereas prokaryotic NSS homologs like LeuT are chloride-independent but contain an acidic residue (Glu290 in LeuT) at a site where eukaryotic NSSs...... have a serine. The LeuT-E290S mutant displays chloride-dependent activity. We show that, in LeuT-E290S cocrystallized with bromide or chloride, the anion is coordinated by side chain hydroxyls from Tyr47, Ser290, and Thr254 and the side chain amide of Gln250. The bound anion and the nearby sodium ion...

  11. Chloride ingress in cement paste and mortar

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, O.M.; Hansen, P.F.; Coats, A.M.; Glasser, F.P.

    1999-09-01

    In this paper chloride ingress in cement paste and mortar is followed by electron probe microanalysis. The influence of several paste and exposure parameters on chloride ingress are examined (e.g., water-cement ratio, silica fume addition, exposure time, and temperature). The measurements are modelled on Fick's law modified by a term for chloride binding. Inclusion of chloride binding significantly improves the profile shape of the modelled ingress profiles. The presence of fine aggregate and formation of interfacial transition zones at paste-aggregate boundaries does not significantly affect diffusion rates.

  12. Green process to recover magnesium chloride from residue solution of potassium chloride production plant

    Institute of Scientific and Technical Information of China (English)

    Lin WANG; Yunliang HE; Yanfei WANG; Ying BAO; Jingkang WANG

    2008-01-01

    The green process to recover magnesium chlor-ide from the residue solution of a potassium chloride pro-duction plant, which comes from the leach solution of a potash mine in Laos, is designed and optimized. The res-idue solution contains magnesium chloride above 25 wt-%, potassium chloride and sodium chloride together below 5 wt-% and a few other ions such as Br-, SO2-4and Ca2+. The recovery process contains two steps: the previous impurity removal operation and the two-stage evapora-tion-cooling crystallization procedure to produce magnes-ium chloride. The crystallized impurity carnallite obtained from the first step is recycled to the potassium chloride plant to recover the potassium salt. The developed process is a zero discharge one and thus fulfills the requirements for green chemical industrial production. The produced magnesium chloride is up to industrial criteria.

  13. ENVIRONMENTAL EXPOSURE TO VINYL CHLORIDE

    Directory of Open Access Journals (Sweden)

    Henryka Langauer-Lewowicka

    2010-09-01

    Full Text Available Vinyl chloride (VC monomer is a wellknown carcinogenic and mutagenic substance causes liver damages, angiosarcoma of the liver, acro – osteolysis, sclerodermalike changes in workers chronically exposed to this gas. There are following VC emitors to the environment: VC production plants, polymerization facilities and planes where polyvinyl products are fabricated. Because of that, the general population is coming into VC contact through polluted air, food and water. VC concentration in all mentioned sites is very low, often not detectable. There was found any health risk for the general population. The VC air concentration in the vicinity to antropogenic emitors is always higher. Such a situation may causes undesirable health effect for residents living in the neighbourhood. Epidemiological studies are performed to detect the adverse VC effect in selected cohorts. Non of the study did not confirmed cases of angiosarcoma among residents living near a vinyl chloride sites. VC production is growing permanently, so VC emission will be higher. Because of that health monitoring of general population and especially of selected groups seems to be necessary in the future.

  14. Comparing polyaluminum chloride and ferric chloride for antimony removal.

    Science.gov (United States)

    Kang, Meea; Kamei, Tasuku; Magara, Yasumoto

    2003-10-01

    Antimony has been one of the contaminants required to be regulated, however, only limited information has been collected to date regarding antimony removal by polyaluminium chloride (PACl) and ferric chloride (FC). Accordingly, the possible use of coagulation by PACl or FC for antimony removal was investigated. Jar tests were used to determine the effects of solution pH, coagulant dosage, and pre-chlorination on the removal of various antimony species. Although high-efficiency antimony removal by aluminum coagulation has been expected because antimony is similar to arsenic in that both antimony and arsenic are a kind of metalloid in group V of the periodic chart, this study indicated: (1) removal density (arsenic or antimony removed per mg coagulant) for antimony by PACl was about one forty-fifth as low as observed for As(V); (2) although the removal of both Sb(III) and Sb(V) by coagulation with FC was much higher than that of PACl, a high coagulant dose of 10.5mg of FeL(-1) at optimal pH of 5.0 was still not sufficient to meet the standard antimony level of 2 microg as SbL(-1) for drinking water when around 6 microg as SbL(-1) were initially present. Consequently, investigation of a more appropriate treatment process is necessary to develop economical Sb reduction; (3) although previous studies concluded that As(V) is more effectively removed than As(III), this study showed that the removal of Sb(III) by coagulation with FC was much more pronounced than that of Sb(V); (4) oxidation of Sb(III) with chlorine decreased the ability of FC to remove antimony. Accordingly, natural water containing Sb(III) under anoxic condition should be coagulated without pre-oxidation.

  15. Electrochemical Behavior of Copper in Thionyl Chloride Solutions.

    Science.gov (United States)

    1980-12-01

    lithium - thionyl chloride batteries . Thionyl chloride is known *3 to react...electrolyte for lithium - thionyl chloride batteries . 8R. K. McAlpine and B. A. Soule, Prescott and Johnson’s Qualitative Chemical Analysis, D. Van...black carbon electrodes, cupric chloride appears to be a useful cathode additive for lithium - thionyl chloride batteries . Preliminary results2l

  16. Chronopotentiometric chloride sensing using transition time measurement

    NARCIS (Netherlands)

    Abbas, Y.; Graaf, de D.B.; Olthuis, W.; Berg, van den A.

    2013-01-01

    Detection of chloride ions is crucial to accurately access the concrete structure durability[1]. The existing electrochemical method of chloride ions detection in concrete, potentiometry[1], is not suitable for in-situ measurement due to the long term stability issue of conventional reference electr

  17. 29 CFR 1915.1017 - Vinyl chloride.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Vinyl chloride. 1915.1017 Section 1915.1017 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... § 1915.1017 Vinyl chloride. Note: The requirements applicable to shipyard employment under this...

  18. 29 CFR 1926.1117 - Vinyl chloride.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Vinyl chloride. 1926.1117 Section 1926.1117 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Toxic and Hazardous Substances § 1926.1117 Vinyl chloride. Note: The requirements applicable to construction work under this section are identical to...

  19. Chemische contaminanten in diervoeder additief Choline Chloride

    NARCIS (Netherlands)

    Traag, W.A.; Hoogenboom, L.A.P.; Jong, de J.; Egmond, van H.J.; Dam, ten G.

    2010-01-01

    Dit briefrapport beschrijft de resultaten van een onderzoek naar chemische contaminanten in Choline Chloride. De doelstellingen waren: 1) Inzicht te verkrijgen in het voorkomen van (gebromeerde) vlamvertragers en broomdioxines in het diervoederadditief Choline Chloride en het, op basis van de result

  20. Chloride ingress in cement paste and mortar

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede; Hansen, Per Freiesleben; Coats, Alison M.

    1999-01-01

    In this paper chloride ingress in cement paste and mortar is followed by electron probe microanalysis. The influence of several paste and exposure parameters on chloride ingress are examined (e.g., water-cement ratio, silica fume addition, exposure time, and temperature), The measurements...

  1. Design of a homogeneous subcritical nuclear reactor based on thorium with a source of californium 252; Diseno de un reactor nuclear subcritico homogeneo a base de Torio con una fuente de Californio 252

    Energy Technology Data Exchange (ETDEWEB)

    Delgado H, C. E.; Vega C, H. R. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico); Sajo B, L., E-mail: ce_delgado89@hotmail.com [Universidad Simon Bolivar, Laboratorio de Fisica Nuclear, Apdo. 89000, 1080A Caracas (Venezuela, Bolivarian Republic of)

    2015-10-15

    Full text: One of the energy alternatives to fossil fuels which do not produce greenhouse gases is the nuclear energy. One of the drawbacks of this alternative is the generation of radioactive wastes of long half-life and its relation to the generation of nuclear materials to produce weapons of mass destruction. An option to these drawbacks of nuclear energy is to use Thorium as part of the nuclear fuel which it becomes in U{sup 233} when capturing neutrons, that is a fissile material. In this paper Monte Carlo methods were used to design a homogeneous subcritical reactor based on thorium. As neutron reflector graphite was used. The reactor core is homogeneous and is formed of 70% light water as moderator, 12% of enriched uranium UO{sub 2}(NO{sub 3}){sub 4} and 18% of thorium Th(NO{sub 3}){sub 4} as fuel. To start the nuclear fission chain reaction an isotopic source of californium 252 was used with an intensity of 4.6 x 10{sup 7} s{sup -1}. In the design the value of the effective multiplication factor, whose value turned out k{sub eff} <1 was calculated. Also, the neutron spectra at different distances from the source and the total fluence were calculated, as well as the values of the ambient dose equivalent in the periphery of the reactor. (Author)

  2. Manganese determination om minerals by activation analysis, using the californium-252 as a neutron source; Determinacao de manganes em minerios, por analise por ativacao, usando californio-252 como fonte de neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Cardoso, Antonio

    1976-07-01

    Neutron Activation Analysis, using a Californium-252 neutron source, has been applied for the determination of manganese in ores such as pyrolusite, rodonite (manganese silicate)' and blending used in dry-batteries The favorable nuclear properties of manganese, such as high thermal neutron cross-section for the reaction {sup 55}Mn (n.gamma){sup 56} Mn, high concentration of manganese in the matrix and short half - life of {sup 56}Mn, are an ideal combination for non-destructive analysis of manganese in ores. Samples and standards of manganese dioxide were irradiated for about 20 minutes, followed by a 4 to 15 minutes decay and counted in a single channel pulse-height discrimination using a NaI(Tl) scintillation detector. Counting time was equal to 10 minutes. The interference of nuclear reactions {sup 56}Fe(n,p){sup 56}Mn and {sup 59} Co (n, {alpha}){sup 56} were studied, as well as problems in connection with neutron shadowing during irradiation, gamma-rays attenuation during counting and influence of granulometry of samples. One sample,was also analysed by wet-chemical method (sodium bismuthate) in order to compare results. As a whole, i t was shown that the analytical method of neutron activation for manganese in ores and blending, is a method simple, rapid and with good precision and accuracy. (author)

  3. Chloride Transport in Undersea Concrete Tunnel

    Directory of Open Access Journals (Sweden)

    Yuanzhu Zhang

    2016-01-01

    Full Text Available Based on water penetration in unsaturated concrete of underwater tunnel, a diffusion-advection theoretical model of chloride in undersea concrete tunnel was proposed. The basic parameters including porosity, saturated hydraulic conductivity, chloride diffusion coefficient, initial water saturation, and moisture retention function of concrete specimens with two water-binder ratios were determined through lab-scale experiments. The variation of chloride concentration with pressuring time, location, solution concentration, initial saturation, hydraulic pressure, and water-binder ratio was investigated through chloride transport tests under external water pressure. In addition, the change and distribution of chloride concentration of isothermal horizontal flow were numerically analyzed using TOUGH2 software. The results show that chloride transport in unsaturated concrete under external water pressure is a combined effect of diffusion and advection instead of diffusion. Chloride concentration increased with increasing solution concentration for diffusion and increased with an increase in water pressure and a decrease in initial saturation for advection. The dominant driving force converted with time and saturation. When predicting the service life of undersea concrete tunnel, it is suggested that advection is taken into consideration; otherwise the durability tends to be unsafe.

  4. Chloride Ingress into Concrete under Water Pressure

    OpenAIRE

    Lund, Mia Schou; Sander, Lotte Braad; Grelk, Bent; Hansen, Kurt Kielsgaard

    2011-01-01

    The chloride ingress into concrete under water pressures of 100 kPa and 800 kPa have been investigated by experiments. The specimens were exposed to a 10% NaCl solution and water mixture. For the concrete having w/c = 0.35 the experimental results show the chloride diffusion coefficient at 800 kPa (~8 atm.) is 12 times greater than at 100 kPa (~1 atm.). For w/c = 0.45 and w/c = 0.55 the chloride diffusion coefficients are 7 and 3 times greater. This means that a change in pressure highly infl...

  5. Reliability-Based Planning of Chloride Measurements

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Engelund, S.

    1996-01-01

    on measurements of the chloride content obtained from the given structure. In the present paper optimal planning of measurements of the chloride content in reinforced concrete structures is considered. It is shown how optimal experimental plans can be obtained using FORM-analysis. Bayesian statistics are used......In reinforced concrete structures corrosion is initiated when the chloride concentration around the reinforcement exceeds a threshold value. If corrosion starts then expensive repairs can be necessary. The estimation of the probability that corrosion has been initiated in a given structure is based...

  6. Catastrophic event modeling. [lithium thionyl chloride batteries

    Science.gov (United States)

    Frank, H. A.

    1981-01-01

    A mathematical model for the catastrophic failures (venting or explosion of the cell) in lithium thionyl chloride batteries is presented. The phenomenology of the various processes leading to cell failure is reviewed.

  7. Surface adsorption in strontium chloride ammines

    DEFF Research Database (Denmark)

    Ammitzbøll, Andreas L.; Lysgaard, Steen; Klukowska, Agata

    2013-01-01

    An adsorbed state and its implications on the ab- and desorption kinetics of ammonia in strontium chloride ammine is identified using a combination of ammonia absorption measurements, thermogravimetric analysis, and density functional theory calculations. During thermogravimetric analysis, ammoni...

  8. Qualitative Determination of Nitrate with Triphenylbenzylphosphonium Chloride.

    Science.gov (United States)

    Berry, Donna A.; Cole, Jerry J.

    1984-01-01

    Discusses two procedures for the identification of nitrate, the standard test ("Brown Ring" test) and a new procedure using triphenylbenzylphosphonium chloride (TPBPC). Effectiveness of both procedures is compared, with the TPBPC test proving to be more sensitive and accurate. (JM)

  9. Corneal Neurotoxicity Due to Topical Benzalkonium Chloride

    OpenAIRE

    Sarkar, Joy; Chaudhary, Shweta; Namavari, Abed; Ozturk, Okan; Chang, Jin-Hong; Yco, Lisette; Sonawane, Snehal; Khanolkar, Vishakha; Hallak, Joelle; Jain, Sandeep

    2012-01-01

    Topical application of benzalkonium chloride (BAK) to the eye causes dose-related corneal neurotoxicity. Corneal inflammation and reduction in aqueous tear production accompany neurotoxicity. Cessation of BAK treatment leads to recovery of corneal nerve density.

  10. Chloride Ingress into Concrete under Water Pressure

    DEFF Research Database (Denmark)

    Lund, Mia Schou; Sander, Lotte Braad; Grelk, Bent;

    2011-01-01

    The chloride ingress into concrete under water pressures of 100 kPa and 800 kPa have been investigated by experiments. The specimens were exposed to a 10% NaCl solution and water mixture. For the concrete having w/c = 0.35 the experimental results show the chloride diffusion coefficient at 800 k......Pa (~8 atm.) is 12 times greater than at 100 kPa (~1 atm.). For w/c = 0.45 and w/c = 0.55 the chloride diffusion coefficients are 7 and 3 times greater. This means that a change in pressure highly influences the chloride ingress into the concrete and thereby the life length models for concrete structures....

  11. 75 FR 20625 - Barium Chloride From China

    Science.gov (United States)

    2010-04-20

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Revised schedule for the subject review. DATES: Effective Date: April 9, 2010. FOR FURTHER INFORMATION CONTACT:...

  12. Telomerization of Vinyl Chloride with Chloroform Initiated by Ferrous Chloride-Dimethylacetamide under Ultrasonic Conditions

    Directory of Open Access Journals (Sweden)

    Hua Qian

    2015-01-01

    Full Text Available Telomerization of vinyl chloride with chloroform was investigated using ferrous chloride-dimethylacetamide system, and 42.1% yield, more than four times the one reported before, was achieved. The addition of ultrasound further improved the reaction and yield was raised to 51.9% with trace byproducts at highly reduced reaction time and temperature. Ferrous chloride-dimethylacetamide under ultrasonic irradiation acts as a very efficient catalyst system for the 1 : 1 telomerization.

  13. Cesium chloride-induced torsades de pointes

    OpenAIRE

    Wiens, Matthew; Gordon, Wendy; Baulcomb, Daisy; Mattman, Andre; Mock, Tom; Brown, Robert

    2009-01-01

    The chloride salt of cesium, a group 1A element, is gaining popularity as an alternative treatment of advanced cancers. Cesium chloride has primarily been used in cardiovascular research for arrhythmogenesis in animals because of its potassium-blocking effects. The present report describes a 45-year-old woman with metastatic breast cancer who experienced repeated episodes of torsades de pointes polymorphic ventricular tachycardia after several months of oral cesium therapy. There was a clear ...

  14. The kinetics of the hydrogen chloride oxidation

    Directory of Open Access Journals (Sweden)

    Gonzalez Martinez Isai

    2013-01-01

    Full Text Available Hydrogen chloride (HCl oxidation has been investigated on technical membrane electrode assemblies in a cyclone flow cell. Influence of Nafion loading, temperature and hydrogen chloride mole fraction in the gas phase has been studied. The apparent kinetic parameters like reaction order with respect to HCl, Tafel slope and activation energy have been determined from polarization data. The apparent kinetic parameters suggest that the recombination of adsorbed Cl intermediate is the rate determining step.

  15. Effect of Chloride Type on Penetration of Chloride Ions in Concrete

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The influence of chloride type on the diffusivity of chloride ions in concrete was studied by experiment. The result shows that the glectric resistance of concrete and the chloride diffusion coefficient are influenced by chloride type. For the same water/cement ratio (W/C), the diffusion coefficient D in KCl solution is larger than that in NaCl solution; however, the concrete resistance in KCl solution is smaller than that in NaCl solution. The experimental result is analyzed with theory of diffusion.

  16. Influence of Chloride-Ion Adsorption Agent on Chloride Ions in Concrete and Mortar

    Directory of Open Access Journals (Sweden)

    Gai-Fei Peng

    2014-04-01

    Full Text Available The influence of a chloride-ion adsorption agent (Cl agent in short, composed of zeolite, calcium aluminate hydrate and calcium nitrite, on the ingress of chloride ions into concrete and mortar has been experimentally studied. The permeability of concrete was measured, and the chloride ion content in mortar was tested. The experimental results reveal that the Cl agent could adsorb chloride ions effectively, which had penetrated into concrete and mortar. When the Cl agent was used at a dosage of 6% by mass of cementitious materials in mortar, the resistance to the penetration of chloride ions could be improved greatly, which was more pronounced when a combination of the Cl agent and fly ash or slag was employed. Such an effect is not the result of the low permeability of the mortar, but might be a result of the interaction between the Cl agent and the chloride ions penetrated into the mortar. There are two possible mechanisms for the interaction between the Cl agent and chloride ion ingress. One is the reaction between calcium aluminate hydrate in the Cl agent and chloride ions to form Friedel’s salt, and the other one is that calcium aluminate hydrate reacts with calcium nitrite to form AFm during the early-age hydration of mortar and later the NO2− in AFm is replaced by chloride ions, which then penetrate into the mortar, also forming Friedel’s salt. More research is needed to confirm the mechanisms.

  17. 42 CFR 84.250 - Vinyl chloride respirators; description.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Vinyl chloride respirators; description. 84.250... Respirators § 84.250 Vinyl chloride respirators; description. Vinyl chloride respirators, including all... escape from vinyl chloride atmospheres containing adequate oxygen to support life, are...

  18. Factors influencing chloride deposition in a coastal hilly area and application to chloride deposition mapping

    Directory of Open Access Journals (Sweden)

    H. Guan

    2009-09-01

    Full Text Available Chloride is commonly used as an environmental tracer for studying water flow and solute transport in the environment. It is especially useful for estimating groundwater recharge based on the commonly used chloride mass balance (CMB method. Strong spatial variability in chloride deposition in coastal areas is one difficulty encountered in appropriately applying the CMB approach. Furthermore, intensive vegetation clearance for agriculture, for example during the European settlement in many coastal areas of Australia, may have perturbed catchment chloride balance conditions for appropriate use in CMB applications. In order to deal with these issues, a high resolution chloride deposition map in the coastal region is needed. In this study, we examined geographic, orographic, and atmospheric factors influencing chloride deposition in the Mount Lofty Ranges (MLR, a coastal hilly area of approximately 9000 km2 spatial extent in South Australia, using partial correlation and regression analyses. The results indicate that coastal distance, and terrain aspect and slope are two most significant factors controlling chloride deposition. Coastal distance accounts for 65% spatial variability in chloride deposition, with terrain aspect and slope for 8%. The deposition gradient is about 0.08 gm-2 year-1 km-1 as one progresses inland. The results are incorporated into a published de-trended residual kriging approach (ASOADeK to produce a 1 km×1 km resolution annual chloride deposition map and a bulk precipitation chloride concentration map. The average uncertainty of the deposition map is about 30% in the western MLR, and over 50% in the eastern MLR. The maps will form a very useful basis for examining catchment chloride balances for use in the CMB application in the study area.

  19. A comprehensive probabilistic model of chloride ingress in unsaturated concrete

    OpenAIRE

    Bastidas-Arteaga, Emilio; Chateauneuf, Alaa; Sánchez-Silva, Mauricio; Bressolette, Philippe; Schoefs, Franck

    2011-01-01

    International audience; Corrosion induced by chloride ions has become a critical issue for many reinforced concrete structures. The chloride ingress into concrete has been usually simplified as a diffusion problem where the chloride concentration throughout concrete is estimated analytically. However, this simplified approach has several limitations. For instance, it does not consider chloride ingress by convection which is essential to model chloride penetration in unsaturated conditions as ...

  20. Inhibition of nitrite-induced toxicity in channel catfish by calcium chloride and sodium chloride

    Science.gov (United States)

    Tommasso J.R., Wright; Simco, B.A.; Davis, K.B.

    1980-01-01

    Environmental chloride has been shown to inhibit methemoglobin formation in fish, thereby offering a protective effect against nitrite toxicity. Channel catfish (Ictalurus punctatus) were simultaneously exposed to various environmental nitrite and chloride levels (as either CaCl2 or NaCl) in dechlorinated tap water (40 mg/L total hardness, 47 mg/L alkalinity, 4 mg/L chloride, pH = 6.9-7.1, and temperature 21-24°C). Methemoglobin levels in fish simultaneously exposed to 2.5 mg/L nitrite and up to 30 mg/L chloride as either CaCl2 or NaCl were similar but significantly lower than in unprotected fish. Exposure to 10 mg/L nitrite and 60 mg/L chloride resulted in methemoglobin levels similar to those of the controls; most unprotected fish died. Fish exposed to 10 mg/L nitrite had significantly lower methemoglobin levels when protected with 15.0 mg/L chloride as CaCl2 than with NaCl. Fish exposed to nitrite in the presence of 60 mg/L chloride (as either CaCl2 or NaCl) had similar 24-h LC50 values that were significantly elevated above those obtained in the absence of chloride. Calcium had little effect on tolerance to nitrite toxicity in channel catfish in contrast to its large effect reported in steelhead trout (Salmo gairdneri).

  1. Congenital Chloride Diarrhea: Diagnosis by Easy-Accessible Chloride Measurement in Feces

    Directory of Open Access Journals (Sweden)

    C. Gils

    2016-01-01

    Full Text Available Background. Congenital chloride diarrhea (CCD is an autosomal recessive disorder caused by mutations in the genes encoding the intestinal Cl−/HCO3- exchanger and is clinically characterized by watery, profound diarrhea, electrolyte disturbances, and metabolic alkalosis. The CCD diagnosis is based on the clinical symptoms and measurement of high chloride concentration in feces (>90 mmol/L and is confirmed by DNA testing. Untreated CCD is lethal, while long-term clinical outcome improves when treated correctly. Case Presentation. A 27-year-old woman had an emergency caesarian due to pain and discomfort in gestational week 36 + 4. The newborn boy had abdominal distension and yellow fluid per rectum. Therapy with intravenous glucose and sodium chloride decreased his stool frequency and improved his clinical condition. A suspicion of congenital chloride diarrhea was strongly supported using blood gas analyzer to measure an increased chloride concentration in the feces; the diagnosis was confirmed by DNA testing. Discussion. Measurement of chloride in feces using an ordinary blood gas analyzer can serve as a preliminary analysis when congenital chloride diarrhea is suspected. This measurement can be easily performed with a watery feces composition. An easy-accessible chloride measurement available will facilitate the diagnostics and support the initial treatment if CCD is suspected.

  2. Amine and Titanium (IV Chloride, Boron (III Chloride or Zirconium (IV Chloride-Promoted Baylis-Hillman Reactions

    Directory of Open Access Journals (Sweden)

    Shi-Cong Cui

    2001-10-01

    Full Text Available The Baylis-Hillman reactions of various aryl aldehydes with methyl vinyl ketone at temperatures below -20oC using Lewis acids such as titanium (IV chloride, boron (III chloride or zirconium (IV chloride in the presence of a catalytic amount of selected amines used as a Lewis bases afford the chlorinated compounds 1 as the major product in very high yields. Acrylonitrile can also undergo the same reaction to give the corresponding chlorinated product in moderate yield. A plausible reaction mechanism is proposed. However, if the reaction was carried out at room temperature (ca. 20oC, then the Z-configuration of the elimination product 3, derived from 1, was formed as the major product.

  3. Dynamic Electrochemical Measurement of Chloride Ions.

    Science.gov (United States)

    Abbas, Yawar; de Graaf, Derk B; Olthuis, Wouter; van den Berg, Albert

    2016-02-05

    This protocol describes the dynamic measurement of chloride ions using the transition time of a silver silver chloride (Ag/AgCl) electrode. Silver silver chloride electrode is used extensively for potentiometric measurement of chloride ions concentration in electrolyte. In this measurement, long-term and continuous monitoring is limited due to the inherent drift and the requirement of a stable reference electrode. We utilized the chronopotentiometric approach to minimize drift and avoid the use of a conventional reference electrode. A galvanostatic pulse is applied to an Ag/AgCl electrode which initiates a faradic reaction depleting the Cl- ions near the electrode surface. The transition time, which is the time to completely deplete the ions near the electrode surface, is a function of the ion concentration, given by the Nernst equation. The square root of the transition time is in linear relation to the chloride ion concentration. Drift of the response over two weeks is negligible (59 µM/day) when measuring 1 mM [Cl-]using a current pulse of 10 Am(-2). This is a dynamic measurement where the moment of transition time determines the response and thus is independent of the absolute potential. Any metal wire can be used as a pseudo-reference electrode, making this approach feasible for long-term measurement inside concrete structures.

  4. Chloride binding site of neurotransmitter sodium symporters.

    Science.gov (United States)

    Kantcheva, Adriana K; Quick, Matthias; Shi, Lei; Winther, Anne-Marie Lund; Stolzenberg, Sebastian; Weinstein, Harel; Javitch, Jonathan A; Nissen, Poul

    2013-05-21

    Neurotransmitter:sodium symporters (NSSs) play a critical role in signaling by reuptake of neurotransmitters. Eukaryotic NSSs are chloride-dependent, whereas prokaryotic NSS homologs like LeuT are chloride-independent but contain an acidic residue (Glu290 in LeuT) at a site where eukaryotic NSSs have a serine. The LeuT-E290S mutant displays chloride-dependent activity. We show that, in LeuT-E290S cocrystallized with bromide or chloride, the anion is coordinated by side chain hydroxyls from Tyr47, Ser290, and Thr254 and the side chain amide of Gln250. The bound anion and the nearby sodium ion in the Na1 site organize a connection between their coordinating residues and the extracellular gate of LeuT through a continuous H-bond network. The specific insights from the structures, combined with results from substrate binding studies and molecular dynamics simulations, reveal an anion-dependent occlusion mechanism for NSS and shed light on the functional role of chloride binding.

  5. Chloride equilibrium potential in salamander cones

    Directory of Open Access Journals (Sweden)

    Bryson Eric J

    2004-12-01

    Full Text Available Abstract Background GABAergic inhibition and effects of intracellular chloride ions on calcium channel activity have been proposed to regulate neurotransmission from photoreceptors. To assess the impact of these and other chloride-dependent mechanisms on release from cones, the chloride equilibrium potential (ECl was determined in red-sensitive, large single cones from the tiger salamander retinal slice. Results Whole cell recordings were done using gramicidin perforated patch techniques to maintain endogenous Cl- levels. Membrane potentials were corrected for liquid junction potentials. Cone resting potentials were found to average -46 mV. To measure ECl, we applied long depolarizing steps to activate the calcium-activated chloride current (ICl(Ca and then determined the reversal potential for the current component that was inhibited by the Cl- channel blocker, niflumic acid. With this method, ECl was found to average -46 mV. In a complementary approach, we used a Cl-sensitive dye, MEQ, to measure the Cl- flux produced by depolarization with elevated concentrations of K+. The membrane potentials produced by the various high K+ solutions were measured in separate current clamp experiments. Consistent with electrophysiological experiments, MEQ fluorescence measurements indicated that ECl was below -36 mV. Conclusions The results of this study indicate that ECl is close to the dark resting potential. This will minimize the impact of chloride-dependent presynaptic mechanisms in cone terminals involving GABAa receptors, glutamate transporters and ICl(Ca.

  6. Efficient cellulose solvent: quaternary ammonium chlorides.

    Science.gov (United States)

    Kostag, Marc; Liebert, Tim; El Seoud, Omar A; Heinze, Thomas

    2013-10-01

    Pure quaternary tetraalkylammonium chlorides with one long alkyl chain dissolved in various organic solvents constitute a new class of cellulose solvents. The electrolytes are prepared in high yields and purity by Menshutkin quaternization, an inexpensive and easy synthesis route. The pure molten tetraalkylammonium chlorides dissolve up to 15 wt% of cellulose. Cosolvents, including N,N-dimethylacetamide (DMA), may be added in large excess, leading to a system of decreased viscosity. Contrary to the well-established solvent DMA/LiCl, cellulose dissolves in DMA/quaternary ammonium chlorides without any pretreatment. Thus, the use of the new solvent avoids some disadvantages of DMA/LiCl and ionic liquids, the most extensively employed solvents for homogeneous cellulose chemistry.

  7. Alkali metal and ammonium chlorides in water and heavy water (binary systems)

    CERN Document Server

    Cohen-Adad, R

    1991-01-01

    This volume surveys the data available in the literature for solid-fluid solubility equilibria plus selected solid-liquid-vapour equilibria, for binary systems containing alkali and ammonium chlorides in water or heavy water. Solubilities covered are lithium chloride, sodium chloride, potassium chloride, rubidium chloride, caesium chloride and ammonium chloride in water and heavy water.

  8. Hazards of lithium thionyl chloride batteries

    Science.gov (United States)

    Parry, J. M.

    1978-01-01

    Two different topics which only relate in that they are pertinent to lithium thionyl chloride battery safety are discussed. The first topic is a hazards analysis of a system (risk assessment), a formal approach that is used in nuclear engineering, predicting oil spills, etc. It is a formalized approach for obtaining assessment of the degree of risk associated with the use of any particular system. The second topic is a small piece of chemistry related to the explosions that can occur with lithium thionyl chloride systems. After the two topics are presented, a discussion is generated among the Workshop participants.

  9. EVALUATION OF BACTERICIDAL EFFECTIVENESS OF BENZALKONIUM CHLORIDE

    Directory of Open Access Journals (Sweden)

    K. Imandel

    1996-06-01

    Full Text Available Benzalkonium chloride is a quaternary ammounium Compounds derivative under different names such as Afxhang, Hamoon, Mahan etc, which have great and expanded use in sanitation and medical affairs. Bactericidal activity of these disinfectants was fulfilled according to National Standard Method No.2842 on Staph. Aureus, Sal. Typhimouium and E. coli. This laboratory test showed that, except Mahan that has not bactericidal efficacy on E.coli at concentration 0.4 percent, other disinfectants under the study in concentrations of 0.4, 0.8, 1, 1.2 percent have reliable antibacterial properties, and bacterial resistance to benzalkonium chloride has not occurred yet.

  10. Cesium chloride-induced torsades de pointes.

    Science.gov (United States)

    Wiens, Matthew; Gordon, Wendy; Baulcomb, Daisy; Mattman, Andre; Mock, Tom; Brown, Robert

    2009-09-01

    The chloride salt of cesium, a group 1A element, is gaining popularity as an alternative treatment of advanced cancers. Cesium chloride has primarily been used in cardiovascular research for arrhythmogenesis in animals because of its potassium-blocking effects. The present report describes a 45-year-old woman with metastatic breast cancer who experienced repeated episodes of torsades de pointes polymorphic ventricular tachycardia after several months of oral cesium therapy. There was a clear temporal relationship between cesium ingestion and the arrhythmia, which later resolved following discontinuation of cesium therapy. Serial cesium plasma and whole blood levels were measured over the ensuing six months and pharmacokinetic analysis was performed.

  11. Solvothermal synthesis of strontium phosphate chloride nanowire

    Science.gov (United States)

    Lam, W. M.; Wong, C. T.; Li, Z. Y.; Luk, K. D. K.; Chan, W. K.; Yang, C.; Chiu, K. Y.; Xu, B.; Lu, W. W.

    2007-08-01

    Strontium phosphate chloride nanowire was synthesized via a solvothermal treatment of strontium tri-polyphosphate and Collin salt in 1,4-dioxane at 150 °C. The effects of 1,4-dioxane concentration on particle morphology, crystallinity and phase purity were investigated in this study. The specimen morphology was analyzed by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). When the concentration of 1,4-dioxane was below 10%, micron-sized whisker was the dominant form. At 20-25% concentration of 1,4-dioxane, strontium phosphate chloride single-crystalline nanowire was 31±12 nm in diameter and 1.43±0.6 μm in length with an aspect ratio of 52.28±29.41. X-ray diffraction (XRD) pattern of this nanowire matched with that of strontium phosphate chloride (JCPDS #083-0973). When 1,4-dioxane concentration exceeded 25%, nanorod aggregate was the dominant form instead of nanowire. At 20-25% 1,4-dioxane concentration suitable strontium concentration combine with high chemical potential environment favors the formation of nanowires. By adding 1,4-dioxane impure phase such as β-strontium hydrogen phosphate, nanorod formation was suppressed. This method provides an efficient way to synthesize high aspect ratio strontium phosphate chloride nanowire. It has potential bioactive nanocomposite, high mechanical performance bioactive bone cement filler and fluorescent material applications.

  12. Controlling chloride ions diffusion in concrete.

    Science.gov (United States)

    Zeng, Lunwu; Song, Runxia

    2013-11-28

    The corrosion of steel in concrete is mainly due to the chemical reaction between the chloride ions and iron ions. Indeed, this is a serious threaten for reinforced concrete structure, especially for the reinforced concrete structure in the sea. So it is urgent and important to protect concrete against chloride ions corrosion. In this work, we report multilayer concrete can cloak chloride ions. We formulated five kinds of concrete A, B, C, D and E, which are made of different proportion of cement, sand and glue, and fabricated six-layer (ABACAD) cylinder diffusion cloak and background media E. The simulation results show that the six-layer mass diffusion cloak can protect concrete against chloride ions penetration, while the experiment results show that the concentration gradients are parallel and equal outside the outer circle in the diffusion flux lines, the iso-concentration lines are parallel outside the outer circle, and the concentration gradients in the inner circle are smaller than those outside the outer circle.

  13. Influence of compaction on chloride ingress

    NARCIS (Netherlands)

    Zlopasa, J.

    2012-01-01

    Experiences from practice show the need for more of an understanding and optimization of the compaction process in order to design a more durable concrete structure. Local variations in compaction are very often the reason for initiation of local damage and initiation of chloride induced corrosion.

  14. Liquid crystalline critical dynamics in decylammonium chloride

    CERN Document Server

    Lee, K W; Lee, C E; Kang, K H; Rhee, C; Kang, J K

    1999-01-01

    Collective chain dynamics and phase transitions in a model biomembrane, decylammonium chloride (C sub 1 sub 0 H sub 2 sub 1 NH sub 3 Cl), were studied by means of proton nuclear magnetic resonance. Our measurements sensitively reflect the critical dynamics associated with the smectic C to smectic A transition of the lipid bilayer.

  15. Chloride migration in concrete with superabsorbent polymers

    DEFF Research Database (Denmark)

    Hasholt, Marianne Tange; Jensen, Ole Mejlhede

    2015-01-01

    Superabsorbent polymers (SAP) can be used as a means for internal curing of concrete. In the present study, the development of transport properties of concrete with SAP is investigated. The chloride migration coefficient according to NT BUILD 492 is used as a measure of this. Twenty concrete mixt...

  16. Gebromeerde vlamvertragers en broomdioxines in Choline Chloride

    NARCIS (Netherlands)

    Egmond, van H.J.; Traag, W.A.; Hoogenboom, L.A.P.

    2008-01-01

    Sinds begin 2008 worden in het Nationaal Plan Diervoeder Choline Chloride monsters (= diervoeder additief) gevonden waarbij de DR CALUX screenings-assay een sterk verdacht signaal geeft, maar bij de GC-HRMS geen dioxines en dl-PCB's worden gevonden. Dit rapport beschrijft de resultaten van nader ond

  17. Amperometric Sensor for Detection of Chloride Ions

    Directory of Open Access Journals (Sweden)

    Rene Kizek

    2008-09-01

    Full Text Available Chloride ion sensing is important in many fields such as clinical diagnosis, environmental monitoring and industrial applications. We have measured chloride ions at a carbon paste electrode (CPE and at a CPE modified with solid AgNO3, a solution of AgNO3 and/or solid silver particles. Detection limits (3 S/N for chloride ions were 100 μM, 100 μM and 10 μM for solid AgNO3, solution of AgNO3 and/or solid silver particles, respectively. The CPE modified with silver particles is the most sensitive to the presence chloride ions. After that we approached to the miniaturization of the whole electrochemical instrument. Measurements were carried out on miniaturized instrument consisting of a potentiostat with dimensions 35 × 166 × 125 mm, screen printed electrodes, a peristaltic pump and a PC with control software. Under the most suitable experimental conditions (Britton-Robinson buffer, pH 1.8 and working electrode potential 550 mV we estimated the limit of detection (3 S/N as 500 nM.

  18. Regulated trafficking of the CFTR chloride channel

    NARCIS (Netherlands)

    Braakman, L.J.; Kleizen, B.; Jonge, H.R. de

    2000-01-01

    The cystic fibrosis transmembrane conductance regulator (CFTR), the ABC transporter encoded by the cystic fibrosis gene, is localized in the apical membrane of epithelial cells where it functions as a cyclic AMP-regulated chloride channel and as a regulator of other ion channels and transporters. Wh

  19. 21 CFR 582.3845 - Stannous chloride.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Stannous chloride. 582.3845 Section 582.3845 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  20. 29 CFR 1910.1017 - Vinyl chloride.

    Science.gov (United States)

    2010-07-01

    ... possible exposure conditions. (2) Protective garments shall be provided clean and dry for each use. (i... Required Authorized Personnel Only (3) Containers of polyvinyl chloride resin waste from reactors or other... which may be useful: A. For kidney dysfunction: urine examination for albumin, red blood cells,...

  1. Spatial variability of chloride in concrete within homogeneously exposed areas

    NARCIS (Netherlands)

    Angst, U.M.; Polder, R.B.

    2014-01-01

    The concept of variability is increasingly considered in service life predictions. This paper reports experimental data on the spatial distribution of chloride in uncracked concrete subjected to homogeneous exposure. Chloride concentrations were measured with potentiometric sensors embedded in concr

  2. Viscosity and density tables of sodium chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Fair, J.A.; Ozbek, H. (comps.)

    1977-04-01

    A file is presented containing tabulated data extracted from the scientific literature on the density and viscosity of aqueous sodium chloride solutions. Also included is a bibliography of the properties of aqueous sodium chloride solutions. (MHR)

  3. Hydrolysis of ferric chloride in solution

    Energy Technology Data Exchange (ETDEWEB)

    Lussiez, G.; Beckstead, L.

    1996-11-01

    The Detox{trademark} process uses concentrated ferric chloride and small amounts of catalysts to oxidize organic compounds. It is under consideration for oxidizing transuranic organic wastes. Although the solution is reused extensively, at some point it will reach the acceptable limit of radioactivity or maximum solubility of the radioisotopes. This solution could be cemented, but the volume would be increased substantially because of the poor compatibility of chlorides and cement. A process has been developed that recovers the chloride ions as HCl and either minimizes the volume of radioactive waste or permits recycling of the radioactive chlorides. The process involves a two-step hydrolysis at atmospheric pressure, or preferably under a slight vacuum, and relatively low temperature, about 200{degrees}C. During the first step of the process, hydrolysis occurs according to the reaction below: FeCl{sub 3 liquid} + H{sub 2}O {r_arrow} FeOCl{sub solid} + 2 HCl{sub gas} During the second step, the hot, solid, iron oxychloride is sprayed with water or placed in contact with steam, and hydrolysis proceeds to the iron oxide according to the following reaction: 2 FeOCl{sub solid} + H{sub 2}O {r_arrow} Fe{sub 2}O{sub 3 solid} + 2 HCl{sub gas}. The iron oxide, which contains radioisotopes, can then be disposed of by cementation or encapsulation. Alternately, these chlorides can be washed off of the solids and can then either be recycled or disposed of in some other way.

  4. Investigation of factors influencing chloride extraction efficiency during electrochemical chloride extraction from reinforcing concrete

    Science.gov (United States)

    Sharp, Stephen R.

    2005-11-01

    Electrochemical chloride extraction (ECE) is an accelerated bridge restoration method similar to cathodic protection, but operates at higher current densities and utilizes a temporary installation. Both techniques prolong the life of a bridge by reducing the corrosion rate of the reinforcing bar when properly applied. ECE achieves this by moving chlorides away from the reinforcement and out of the concrete while simultaneously increasing the alkalinity of the electrolyte near the reinforcing steel. Despite the proven success, significant use of ECE has not resulted in part due to an incomplete understanding in the following areas: (1) An estimation of the additional service life that can be expected following treatment when the treated member is again subjected to chlorides; (2) The cause of the decrease in current flow and, therefore, chloride removal rate during treatment; (3) Influence of water-to-cement (w/c) ratio and cover depth on the time required for treatment. This dissertation covers the research that is connected to the last two areas listed above. To begin examining these issues, plain carbon steel reinforcing bars (rebar) were embedded in portland cement concrete slabs of varying water-to-cement (w/c) ratios and cover depths, and then exposed to chlorides. A fraction of these slabs had sodium chloride added as an admixture, with all of the slabs subjected to cyclical ponding with a saturated solution of sodium chloride. ECE was then used to remove the chlorides from these slabs while making electrical measurements in the different layers between the rebar (cathode) and the titanium mat (anode) to follow the progress of the ECE process. During this study, it was revealed that the resistance of the outer concrete surface layer increases during ECE, inevitably restricting current flow, while the resistance of the underlying concrete decreases or remains constant. During ECE treatment, a white residue formed on the surface of the concrete. Analyses of the

  5. Aspergilli Response to Benzalkonium Chloride and Novel-Synthesized Fullerenol/Benzalkonium Chloride Nanocomposite

    OpenAIRE

    Nikola Unković; Milica Ljaljević Grbić; Miloš Stupar; Jelena Vukojević; Vesna Janković; Danica Jović; Aleksandar Djordjević

    2015-01-01

    A comprehensive comparative analysis of antifungal potential of benzalkonium chloride and newly synthesized fullerenol/benzalkonium chloride nanocomposite was conducted to assess the possible impact of carbon-based nanocarrier on antimicrobial properties of the commonly used biocide. Physical characterization of synthesized nanocomposite showed zeta potential of +37.4 mV and inhomogeneous particles size distribution, with nanocomposite particles’ dimensions within 30–143 nm and maximum number...

  6. Prenatal susceptibility to carcinogenesis by xenobiotic substances including vinyl chloride.

    OpenAIRE

    Rice, J M

    1981-01-01

    The carcinogenicity of vinyl chloride for experimental animals when administered transplacentally is reviewed in comparison with known transplacental carcinogens, including those that, like vinyl chloride, are dependent on enzyme-mediated metabolic conversion to a reactive intermediate in maternal or fetal tissues. Vinyl chloride is converted by mixed-function oxidases to the reactive metabolite chlorooxirane, the carcinogenicity of which is also reviewed. Vinyl chloride is unequivocally a tr...

  7. Stability of Alprostadil in 0.9% Sodium Chloride Stored in Polyvinyl Chloride Containers.

    Science.gov (United States)

    McCluskey, Susan V; Kirkham, Kylian; Munson, Jessica M

    2017-01-01

    The stability of alprostadil diluted in 0.9% sodium chloride stored in polyvinyl chloride (VIAFLEX) containers at refrigerated temperature, protected from light, is reported. Five solutions of alprostadil 11 mcg/mL were prepared in 250 mL 0.9% sodium chloride polyvinyl chloride (PL146) containers. The final concentration of alcohol was 2%. Samples were stored under refrigeration (2°C to 8°C) with protection from light. Two containers were submitted for potency testing and analyzed in duplicate with the stability-indicating high-performance liquid chromatography assay at specific time points over 14 days. Three containers were submitted for pH and visual testing at specific time points over 14 days. Stability was defined as retention of 90% to 110% of initial alprostadil concentration, with maintenance of the original clear, colorless, and visually particulate-free solution. Study results reported retention of 90% to 110% initial alprostadil concentration at all time points through day 10. One sample exceeded 110% potency at day 14. pH values did not change appreciably over the 14 days. There were no color changes or particle formation detected in the solutions over the study period. This study concluded that during refrigerated, light-protected storage in polyvinyl chloride (VIAFLEX) containers, a commercial alcohol-containing alprostadil formulation diluted to 11 mcg/mL with 0.9% sodium chloride 250 mL was stable for 10 days.

  8. 21 CFR 172.165 - Quaternary ammonium chloride combination.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Quaternary ammonium chloride combination. 172.165... HUMAN CONSUMPTION Food Preservatives § 172.165 Quaternary ammonium chloride combination. The food additive, quaternary ammonium chloride combination, may be safely used in food in accordance with...

  9. Intrinsic Resistance of Burkholderia cepacia Complex to Benzalkonium Chloride

    OpenAIRE

    Youngbeom Ahn; Jeong Myeong Kim; Ohgew Kweon; Seong-Jae Kim; Jones, Richard C.; Kellie Woodling; Goncalo Gamboa da Costa; LiPuma, John J.; David Hussong; Marasa, Bernard S.; Cerniglia, Carl E.

    2016-01-01

    ABSTRACT Pharmaceutical products that are contaminated with Burkholderia cepacia complex (BCC) bacteria may pose serious consequences to vulnerable patients. Benzyldimethylalkylammonium chloride (BZK) cationic surfactants are extensively used in medical applications and have been implicated in the coselection of antimicrobial resistance. The ability of BCC to degrade BZK, tetradecyldimethylbenzylammonium chloride (C14BDMA-Cl), dodecyldimethylbenzylammonium chloride (C12BDMA-Cl), decyldimethyl...

  10. Retention of vinyl chloride in the human lung.

    OpenAIRE

    Krajewski, J.; Dobecki, M; Gromiec, J

    1980-01-01

    Experiments with volunteers showed that 42% of an inhaled dose of vinyl chloride is retained in the lungs. This value is independent of the concentration of vinyl chloride in the air. Elimination of vinyl chloride through the lungs is negligible since its concentration in expired air decreases immediately after the cessation of exposure.

  11. Kinetics of Vinyl Chloride Polymerization with Mixture of Initiators

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Kinetic models for the rate constants of vinyl chloride polymerization in the presence of initiator mixtures were proposed. They may be used to design the initiator recipes for the vinyl chloride polymerization with uniform rate at different temperatures at which various grades of poly(vinyl chloride) will be prepared.

  12. 46 CFR 154.1740 - Vinyl chloride: Inhibiting and inerting.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Vinyl chloride: Inhibiting and inerting. 154.1740... Operating Requirements § 154.1740 Vinyl chloride: Inhibiting and inerting. When a vessel is carrying vinyl chloride, the master shall ensure that: (a) Section 154.1818 is met; or (b) Section 154.1710 is met,...

  13. Relation between chloride exchange diffusion and a conductive chloride pathway across the isolated skin of the toad (Bufo bufo)

    DEFF Research Database (Denmark)

    Kristensen, P; Larsen, Erik Hviid

    1978-01-01

    Substitution of chloride in the outside bathing medium of the toad skin with bromide, iodide, nitrate and sulphate leads to a reduction in the apparent exchange diffusion of chloride across this tissue, and also to a reduction of the chloride current recorded during hyperpolarization. A series of...

  14. 40 CFR 61.64 - Emission standard for polyvinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... Standard for Vinyl Chloride § 61.64 Emission standard for polyvinyl chloride plants. An owner or operator of a polyvinyl chloride plant shall comply with the requirements of this section and § 61.65. (a... is not to exceed 0.02 g vinyl chloride/kg (0.04 lb vinyl chloride/ton) of polyvinyl chloride...

  15. Calcium/thionyl chloride battery technology

    Science.gov (United States)

    Counts, T.

    1985-12-01

    This final report documents the development efforts conducted by the Lithium Batteries Group of the Couples Department of Eagle-Picher Industries. The objective of the project was to develop calcium-thionyl chloride cell technology. The original project was divided into two main tasks. Task One was to consist of component optimization and stability studies. Once sufficiently advanced, the ongoing results of Task One were to be integrated with Task Two. Task Two was to consist of demonstration of an optimized primary cell. In July, 1983, the program was redirected. Task Two was split, with effort to be directed toward both the original primary cell and toward a high discharge rate reserve configuration cell. Additional electrolyte salts were to be evaluated as a means of improving the storability of the active calcium-thionyl chloride cell.

  16. Benzalkonium chloride. Health hazard evaluation report

    Energy Technology Data Exchange (ETDEWEB)

    Bernholc, N.M.

    1984-01-01

    Health hazards associated with the use of benzalkonium chlorides (BAC) are reviewed. Benzalkonium chloride is extensively used as a cationic disinfectant. It is found in a great many over-the-counter and prescription eye products, disinfectants, shampoos, and deodorants, and is used in concentrations that range from 0.001 to 0.01% in eyedrops, up to 2.5% in concentrated liquid disinfectants. Solutions of 0.03 to 0.04% BAC may cause temporary eye irritation in humans but are unlikely to cause any skin response except in persons allergic to quaternary ammonium compounds. Inhalation of a vaporized 10% solution of BAC produced a bronchospasmodic reaction in a previously sensitized individual. At present no other human health effects from BAC have been documented or inferred from exposure to such dilute concentrations.

  17. BARRIER PROPERTIES OF VINYLIDENE CHLORIDE COPOLYMERS

    Institute of Scientific and Technical Information of China (English)

    LI Yuesheng; WENG Zhixue; HUANG Zhiming; PAN Zuren

    1996-01-01

    The permeability coefficients of a series of copolymers of vinylidene chloride (VDC)with methyl acrylate (MA), butyl acrylate (BA) or vinyl chloride (VC) (as comonomer)to oxygen and carbon dioxide have been measured at 1.0 MPa and 30℃, while those to water vapor have been measured at 30℃ and 100% relative humidity. All the copolymers are semicrystalline. VDC/MA copolymers have lower melting temperature compared with VDC/BA copolymers, while that melting temperature of VDC/VC copolymer is higher than that of VDC/acrylate copolymers with the same VDC content. The barrier property of the copolymers is predominantly controlled by crystallite, free volume fraction, and cohesive energy. The permeability coefficients of VDC/MA copolymers to oxygen, carbon dioxide, and water vapor were successfully correlated with the ratio of free volume to cohesive energy.

  18. STABILISATION OF SILTY CLAY SOIL USING CHLORIDE

    Directory of Open Access Journals (Sweden)

    TAMADHER T. ABOOD

    2007-04-01

    Full Text Available The object of this paper is to investigate the effect of adding different chloride compounds including (NaCl, MgCl2, CaCl2 on the engineering properties of silty clay soil. Various amounts of salts (2%, 4%, and 8% were added to the soil to study the effect of salts on the compaction characteristics, consistency limits and compressive strength. The main findings of this study were that the increase in the percentage of each of the chloride compounds increased the maximum dry density and decrease the optimum moisture content. The liquid limit, plastic limit and plasticity index decreased with the increase in salt content. The unconfinedcompressive strength increased as the salt content increased.

  19. Iron (III) chloride doping of CVD graphene.

    Science.gov (United States)

    Song, Yi; Fang, Wenjing; Hsu, Allen L; Kong, Jing

    2014-10-03

    Chemical doping has been shown as an effective method of reducing the sheet resistance of graphene. We present the results of our investigations into doping large area chemical vapor deposition graphene using Iron (III) Chloride (FeCl(3)). It is shown that evaporating FeCl(3) can increase the carrier concentration of monolayer graphene to greater than 10(14) cm(-2) and achieve resistances as low as 72 Ω sq(-1). We also evaluate other important properties of the doped graphene such as surface cleanliness, air stability, and solvent stability. Furthermore, we compare FeCl(3) to three other common dopants: Gold (III) Chloride (AuCl(3)), Nitric Acid (HNO(3)), and TFSA ((CF(3)SO(2))(2)NH). We show that compared to these dopants, FeCl(3) can not only achieve better sheet resistance but also has other key advantages including better solvent stability.

  20. Benzalkonium Chloride Intoxication Mimicking Herpes Zoster Encephalitis

    OpenAIRE

    Güler, Ekrem; Olgar, Şeref; Davutoğlu, Mehmet; Garipardıç, Mesut; Karabiber, Hamza

    2011-01-01

    Benzalkonium chloride (BAC) is a frequently used disinfectant and its most well-known side effect is contact dermatitis. In this report, two children who had vesicular dermatitis, headache, lethargy, fever and encephalopathy mimicking Herpes zoster encephalitis were presented. Their consciousness level improved on the second day. From the medical history it was understood that the mother had applied 20% BAC solution to the scalps of two children. The aim of the presentation of this report is ...

  1. Benzalkonium Chloride Intoxication Mimicking Herpes Zoster Encephalitis

    OpenAIRE

    Ekrem Güler; Şeref Olgar; Mehmet Davutoğlu; Mesut Garipardıç; Hamza Karabiber

    2014-01-01

    Benzalkonium chloride (BAC) is a frequently used disinfectant and its most well-known side effect is contact dermatitis. In this report, two children who had vesicular dermatitis, headache, lethargy, fever and encephalopathy mimicking Herpes zoster encephalitis were presented. Their consciousness level improved on the second day. From the medical history it was understood that the mother had applied 20% BAC solution to the scalps of two children. The aim of the presentation of this report is...

  2. EVALUATION OF BACTERICIDAL EFFECTIVENESS OF BENZALKONIUM CHLORIDE

    OpenAIRE

    K. Imandel; M.B. Shaywaard; F. Mobaraki

    1996-01-01

    Benzalkonium chloride is a quaternary ammounium Compounds derivative under different names such as Afxhang, Hamoon, Mahan etc, which have great and expanded use in sanitation and medical affairs. Bactericidal activity of these disinfectants was fulfilled according to National Standard Method No.2842 on Staph. Aureus, Sal. Typhimouium and E. coli. This laboratory test showed that, except Mahan that has not bactericidal efficacy on E.coli at concentration 0.4 percent, other disinfectants under ...

  3. Inactivation of Viruses by Benzalkonium Chloride

    Science.gov (United States)

    Armstrong, J. A.; Froelich, E. J.

    1964-01-01

    Benzalkonium chloride (as Roccal or Zephiran) was found to inactivate influenza, measles, canine distemper, rabies, fowl laryngotracheitis, vaccinia, Semliki Forest, feline pneumonitis, meningopneumonitis, and herpes simplex viruses after 10 min of exposure at 30 C or at room temperature. Poliovirus and encephalomyocarditis virus were not inactivated under the same conditions. It was concluded that all viruses tested were sensitive except members of the picorna group. The literature was reviewed. PMID:4288740

  4. Electrochemical Studies in Aluminum Chloride Melts

    Science.gov (United States)

    1976-07-31

    Molten Salt Systems", Symposium on Molten Salts, Symposium Volume, The Electrochemical Society , in press (1976). Manuscripts in Preparation--Related to...Fused Salt Technology, Electrochemical Society Meeting, Chicaao, May 8-13, 1973. R. A. Osteryoung, R. H. Abel, L. G. Boxall and B. H. Vassos, "An...aluminate Melts", Electrochemical Society , San Francisco, CA, May, 1974. R. A. Osteryoung, "Chemistry in Aluminum Chloride Melts", Fifth International

  5. Developing Polymer Cathode Material for the Chloride Ion Battery.

    Science.gov (United States)

    Zhao, Xiangyu; Zhao, Zhigang; Yang, Meng; Xia, Hui; Yu, Tingting; Shen, Xiaodong

    2017-01-25

    The chloride ion battery is an attractive rechargeable battery owing to its high theoretical energy density and sustainable components. An important challenge for research and development of chloride ion batteries lies in the innovation of the cathode materials. Here we report a nanostructured chloride ion-doped polymer, polypyrrole chloride, as a new type of potential cathode material for the chloride ion battery. The as-prepared polypyrrole chloride@carbon nanotubes (PPyCl@CNTs) cathode shows a high reversible capacity of 118 mAh g(-1) and superior cycling stability. Reversible electrochemical reactions of the PPyCl@CNTs cathode based on the redox reactions of nitrogen species and chloride ion transfer are demonstrated. Our work may guide and offer electrode design principles for accelerating the development of rechargeable batteries with anion transfer.

  6. The Accelerated Test of Chloride Permeability of Concrete

    Institute of Scientific and Technical Information of China (English)

    TAN Ke-feng; ODD E Gjφrv

    2003-01-01

    The availability of accelerated chloride permeability test and the effect of w/c ratio, incorporation of silica fume, maximum aggregate size and aggregate type on the chloride permeability were studied. The mathematic analysis certifies that there is a linear relationship between accelerated test and natural diffusion. Test results show that the chloride permeability of concrete increases as w/c ratio increases whilst a limited amount of replacement of cement with silica fume, the chloride permeability decreases dramatically. The maximum aggregate size in the range of 8 to 25 mm seems also affect chloride permeability but with a much less significant level. The chloride permeability of silica fume lightweight aggregate concrete is very low, especially the concrete made with dry lightweight concrete. The chloride permeability can be evaluated by this accelerated test method.

  7. Potassium chloride production by microcline chlorination

    Energy Technology Data Exchange (ETDEWEB)

    Orosco, Pablo, E-mail: porosco@unsl.edu.ar [Instituto de Investigaciones en Tecnología Química (INTEQUI), Chacabuco y Pedernera, San Luis (Argentina); Facultad de Química, Bioquímica y Farmacia, Universidad Nacional de San Luis, Chacabuco y Pedernera, San Luis (Argentina); Ruiz, María del Carmen [Instituto de Investigaciones en Tecnología Química (INTEQUI), Chacabuco y Pedernera, San Luis (Argentina)

    2015-08-10

    Highlights: • Use of chlorination for the KCl production. • The reagents used were microcline, hydromagnesite and chlorine. • Isothermal and non-isothermal assays were performed in Cl{sub 2}–N{sub 2} mixture. • The chlorination generated KCl at 700 °C. • The chlorination products promote KCl formation. - Abstract: The potassium chloride is one of the most important fertilizers used in agriculture. The current demand of this salt makes interesting the study of potassium chloride production from unconventional potassium resources. In this work the potassium chloride production by chlorination of microcline was investigated. The starting reagents were microcline, hydromagnesite and chlorine. Non-isothermal and isothermal chlorination assays were carried out in a thermogravimetric device adapted to work in corrosive atmospheres. The temperature effect on potassium extraction and the phase transformations produced during chlorination of microcline were studied. The reagents and reaction products were analyzed by X-ray fluorescence (XRF) and X-ray diffraction (XRD). The experimental results indicated that by chlorination of microcline an important extraction of potassium in the temperature range from 800 to 900 °C was produced. Moreover, at 800 °C the forsterite, enstatite and magnesium aluminate spinel phases were generated.

  8. Boldine action against the stannous chloride effect.

    Science.gov (United States)

    Reiniger, I W; Ribeiro da Silva, C; Felzenszwalb, I; de Mattos, J C; de Oliveira, J F; da Silva Dantas, F J; Bezerra, R J; Caldeira-de-Araújo, A; Bernardo-Filho, M

    1999-12-15

    Peumus boldus extract has been used in popular medicine in the treatment of biliar litiase, hepatic insufficiency and liver congestion. Its effects are associated to the substance boldine that is present in its extract. In the present work, we evaluated the influence of boldine both in: (i) the structural conformation of a plasmid pUC 9.1 through gel electrophoresis analysis; and in (ii) the survival of the strain of Escherichia coli AB1157 submitted to reactive oxygen species (ROS), generated by a Fenton like reaction, induced by stannous chloride. Our results show a reduction of the lethal effect induced by stannous chloride on the survival of the E. coli culture in the presence of boldine. The supercoiled form of the plasmid is not modified by stannous chloride in the presence of boldine. We suggest that the protection induced by boldine could be explained by its anti-oxidant mechanism. In this way, the boldine could be reacting with stannous ions, protecting them against the oxidation and, consequently, avoiding the generation of ROS.

  9. Understanding microwave vessel contamination by chloride species.

    Science.gov (United States)

    Recchia, Sandro; Spanu, Davide; Bianchi, Davide; Dossi, Carlo; Pozzi, Andrea; Monticelli, Damiano

    2016-10-01

    Microwaves are widely used to assist digestion, general sample treatment and synthesis. The use of aqua regia is extensively adopted for the closed vessel mineralization of samples prior to trace element detection, leading to the contamination of microwave vessels by chlorine containing species. The latter are entrapped in the polymeric matrix of the vessels, leading to memory effects that are difficult to remove, among which the risk of silver incomplete recoveries by removal of the sparingly soluble chloride is the predominant one. In the present paper, we determined by mass spectrometry that hydrogen chloride is the species entrapped in the polymeric matrix and responsible for vessel contamination. Moreover, several decontamination treatments were considered to assess their efficiency, demonstrating that several cleaning cycles with water, nitric acid or silver nitrate in nitric acid were inefficient in removing chloride contamination (contamination reduction around 90%). Better results (≈95% decrease) were achieved by a single decontamination step in alkaline environment (sodium hydroxide or ammonia). Finally, a thermal treatment in a common laboratory oven (i.e. without vacuum and ventilation) was tested: a one hour heating at 150°C leads to a 98.5% decontamination, a figure higher than the ones obtained by wet treatments which requires comparable time. The latter treatment is a major advancement with respect to existing treatments as it avoids the need of a vacuum oven for at least 17h as presently proposed in the literature.

  10. Anti-chloride permeability and anti-chloride corrodibility of a green high performance concrete admixture in concrete

    Institute of Scientific and Technical Information of China (English)

    ZHENG Yongbao; LIU Xinrong; LIU Dongyan; CHEN Jiangong; HUANG Xiongjun

    2003-01-01

    The effects of green high performance concrete (GHPC) admixture on the anti-chloride permeability and anti- chloride corrodibility of concrete are studied by a series of experiments designed on the basis of the diffusion principle and electrochemical principle. The GHPC admixture consists of fly ash, gangue, slag, red mud, etc., of which the mass fraction of industrial residues is over 96 %. The anti-permeabilities and anti-corrodibilities of the tested GHPC and normal concrete (NC) are evaluated by the Diffusion Coefficients of chloride which was obtained by measuring the concentration of chloride in the tested systems by the voltage difference method. It is found that the adoption of GHPC admixture greatly improves the anti-chloride permeability and anti-chloride corrodibility by modifying the inner structure and contracting the porosity of concrete to the reduce considerably the diffusion rate of chloride. The admixture is desirable regarding its engineering performances as well as economical and environmental interests.

  11. Chloride Ingress in Concrete with Different Age at Time of First Chloride Exposure

    DEFF Research Database (Denmark)

    Hansen, Esben Østergaard; Iskau, Martin Riis; Hasholt, Marianne Tange

    2016-01-01

    Concrete structures cast in spring have longer time to hydrate and are therefore denser and more resistant to chloride ingress when first subjected to deicing salts in winter than structures cast in autumn. Consequently, it is expected that a spring casting will have a longer service life....... This hypothesis is investigated in the present study by testing drilled cores from concrete cast in 2012 and 2013 on the Svendborgsund Bridge. The cores are subject to petrographic examination and mapping of chloride profiles. Moreover, chloride migration coefficients have been measured. The study shows...... that the effect of the extra time of hydration obtained when casting in spring increases the expected service life of the concrete structure significantly....

  12. Benzalkonium Chloride Intoxication Mimicking Herpes Zoster Encephalitis

    Directory of Open Access Journals (Sweden)

    Ekrem Güler

    2011-06-01

    Full Text Available Benzalkonium chloride (BAC is a frequently used disinfectant and its most well-known side effect is contact dermatitis. In this report, two children who had vesicular dermatitis, headache, lethargy, fever and encephalopathy mimicking Herpes zoster encephalitis were presented. Their consciousness level improved on the second day. From the medical history it was understood that the mother had applied 20% BAC solution to the scalps of two children. The aim of the presentation of this report is to draw attention to the fact that BAC application to the scalp for treating pediculosis capitis may resemble the herpes encephalitis clinical picture.

  13. N-(2-Benzoylethylpropan-2-aminium chloride

    Directory of Open Access Journals (Sweden)

    Abdullah Aydın

    2012-09-01

    Full Text Available In the title salt, C12H18NO+·Cl−, N—H...Cl interactions between the free chloride anions and the organic cations connect the molecules into hydrogen-bond dimers, forming a R22(8 motif. The dimers are linked by C—H...O hydrogen bonds into chains extending along [301]. The carbonyl group is co-planar with the phenyl ring [C—C—C=O torsion angle = −3.3 (7°]. The side chain has an E conformation.

  14. Oral cadmium chloride intoxication in mice

    DEFF Research Database (Denmark)

    Andersen, O; Nielsen, J B; Svendsen, P

    1988-01-01

    Diethyldithiocarbamate (DDC) is known to alleviate acute toxicity due to injection of cadmium salts. However, when cadmium chloride was administered by the oral route, DDC enhanced rather than alleviated the acute toxicity; both oral and intraperitoneal (i.p.) administration of DDC had this effect....... Thus, orally administered DDC enhanced cadmium-induced duodenal and ileal tissue damage and inhibition of peristalsis, as indicated by an increased intestinal transit time. At low cadmium doses, the whole-body retention of cadmium was increased by oral DDC administration. Intraperitoneally administered...

  15. Synthesis of Aminolaurylpyridinium Chloride as Antimicrobial Agent

    Institute of Scientific and Technical Information of China (English)

    ZHAO Tao; SONG Xin-yuan; SUN Gang

    2008-01-01

    4-amino-laurylpyridinium chloride (ALPC) was synthesized and employed in antimicrobial finishing of wool fabrics. The structures of the salt was fully characterized by using FTIR, 1 H-NMR and 13 C-NMR analysis. The effects of pH conditions of finishing baths, finishing time and temperature, and salt concentrations were investigated. ALPC could form ionic interactions with anionic groups on wool, which contribute to durable antimicrobial functions. The finished wool fabrics exhibited antimicrobial efficacy against Escherichia coli. The washing durability of antimicrobial functions on the finished wool fabrics was also studied.

  16. Magnesium anode for chloride ion batteries.

    Science.gov (United States)

    Zhao, Xiangyu; Li, Qiang; Zhao-Karger, Zhirong; Gao, Ping; Fink, Karin; Shen, Xiaodong; Fichtner, Maximilian

    2014-07-23

    A key advantage of chloride ion battery (CIB) is its possibility to use abundant electrode materials that are different from those in Li ion batteries. Mg anode is presented as such a material for the first time and Mg/C composite prepared by ball milling of Mg and carbon black powders or thermally decomposed MgH2/C composite has been tested as anode for CIB. The electrochemical performance of FeOCl/Mg and BiOCl/Mg was investigated, demonstrating the feasibility of using Mg as anode.

  17. Chloride diffusion in partially saturated cementitious material

    DEFF Research Database (Denmark)

    Nielsen, Erik Pram; Geiker, Mette Rica

    2003-01-01

    The paper proposes a combined application of composite theory and Powers' model for microstructural development for the estimation of the diffusion coefficient as a function of the moisture content of a defect-free cementitious material. Measurements of chloride diffusion in mortar samples (440 kg....../m(3) rapid-hardening Portland cement, w/c = 0.5, maturity minimum 6 months) stored at 65% and 85% RH, as well as in vacuum-saturated mortar samples, illustrate the applicability of the method. (C) 2003 Elsevier Science Ltd. All rights reserved....

  18. Chloride regulates afferent arteriolar contraction in response to depolarization

    DEFF Research Database (Denmark)

    Hansen, P B; Jensen, B L; Skott, O

    1998-01-01

    . The results show that K+-induced contraction of smooth muscle cells in the afferent arteriole is highly sensitive to chloride, whereas neurotransmitter release and ensuing contraction is not dependent on chloride. Thus, there are different activation pathways for depolarizing vasoconstrictors......-Renal vascular reactivity is influenced by the level of dietary salt intake. Recent in vitro data suggest that afferent arteriolar contractility is modulated by extracellular chloride. In the present study, we assessed the influence of chloride on K+-induced contraction in isolated perfused rabbit...... afferent arterioles. In 70% of vessels examined, K+-induced contraction was abolished by acute substitution of bath chloride. Consecutive addition of Cl- (30, 60, 80, 100, 110, and 117 mmol/L) restored the sensitivity to K+, and half-maximal response was observed at 82 mmol/L chloride. The calcium channel...

  19. Investigation of Lithium-Thionyl Chloride Battery Safety Hazards.

    Science.gov (United States)

    1983-01-01

    LITHIUM - THIONYL CHLORIDE BATTERY SAFETY HAZARDS(U) GOULD RESEARCH CENTER ROLLING MEADOWS IL MATERIALS LAB A I ATTIA ET...838-012 7 ontract No. 60921-81-C-0363 6// Investigation of Lithium - Thionyl Chloride Battery Safety Hazards AD A 1 T 2 , Alan I. Attia Gould Research...REPORT & PERIOD COVERED Investigation of Lithium - Thionyl Chloride Final Report Battery Safety Hazards 9/28/81 - 12/31/82 6. PERFORMING ORG. REPORT

  20. Surface Chloride Concentration of Concrete under Shallow Immersion Conditions

    OpenAIRE

    Jun Liu; Kaifeng Tang; Dong Pan; Zongru Lei; Weilun Wang; Feng Xing

    2014-01-01

    Deposition of chloride ions in the surface layer of concrete is investigated in this study. In real concrete structure, chloride ions from the service environment can penetrate into concrete and deposit in the surface layer, to form the boundary condition for further diffusion towards the interior. The deposit amount of chloride ions in the surface layer is normally a function of time, rather than a constant. In the experimental investigation, concrete specimens with different mix proportions...

  1. Chloride ingress profiles measured by electron probe micro analysis

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, O.M. [Univ. of Aberdeen (United Kingdom). Dept. of Chemistry]|[Technical Univ. of Denmark, Lyngby (Denmark). Dept. of Structural Engineering and Materials; Coats, A.M.; Glasser, F.P. [Univ. of Aberdeen (United Kingdom). Dept. of Chemistry

    1996-11-01

    Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA is demonstrated to determine chloride ingress in cement paste on a micrometer scale. Potential chloride ingress routes such as cracks or the paste-aggregate interface may also be characterized by EPMA.

  2. Chloride ingress profiles measured by electron probe micro analysis

    DEFF Research Database (Denmark)

    Jensen, Ole mejlhede; Coats, Alison M.; Glasser, Fred P.

    1996-01-01

    Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA...... is demonstated to determine chloride ingress in cement paste on a micrometer scale. Potential chloride ingress routes such as cracks or the paste-aggregate interface may also be characterized by EPMA. Copyright (C) 1996 Elsevier Science Ltd...

  3. On barium oxide solubility in barium-containing chloride melts

    Energy Technology Data Exchange (ETDEWEB)

    Nikolaeva, Elena V.; Zakiryanova, Irina D.; Bovet, Andrey L.; Korzun, Iraida V. [Ural Federal Univ., Yekaterinburg (Russian Federation). Inst. of High Temperature Electrochemistry

    2016-11-01

    Oxide solubility in chloride melts depends on temperature and composition of molten solvent. The solubility of barium oxide in the solvents with barium chloride content is essentially higher than that in molten alkali chlorides. Spectral data demonstrate the existence of oxychloride ionic groupings in such melts. This work presents the results of the BaO solubility in two molten BaCl{sub 2}-NaCl systems with different barium chloride content. The received data together with earlier published results revealed the main regularities of BaO solubility in molten BaO-BaCl{sub 2}-MCl systems.

  4. Stochastic modeling of reinforced concrete structures exposed to chloride attack

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Frier, Christian

    2004-01-01

    the reinforcement exceeds a critical threshold value. In the present paper a stochastic model is described by which the chloride content in a reinforced concrete structure can be estimated. The chloride ingress is modeled by a 2-dimensional diffusion process and the diffusion coefficient, surface chloride......For many reinforced concrete structures corrosion of reinforcement is an important problem since it can result in expensive maintenance and repair actions. Further, a significant reduction of the load-bearing capacity can occur. One mode of corrosion initiation is that the chloride content around...

  5. Fire's effect on chloride ingress related durability of concrete structure

    Institute of Scientific and Technical Information of China (English)

    JIN Wei-liang; ZHANG Yi

    2007-01-01

    This paper describes the effects of fire on durability of reinforced concrete structures, and points out that fire not only damages the chemical composition and physical structure of concrete by high temperature, but also leads to an additional risk due to the generation of polyvinyl chloride (PVC)combustion gases. A mathematical model is proposed to calculate chloride ingress profiles in fire damaged concrete, so as to explore the service life prediction of the structure. Rapid Chloride Migration (RCM) test was carried out to determine the chloride diffusion coefficients for the application of the mathematical model. Finally, the detected results of a reported case testified to the validity of the mathematical model.

  6. Catalytic Conversion of Cellulose to Levulinic Acid by Metal Chlorides

    Directory of Open Access Journals (Sweden)

    Beixiao Zhang

    2010-08-01

    Full Text Available The catalytic performance of various metal chlorides in the conversion of cellulose to levulinic acid in liquid water at high temperatures was investigated. The effects of reaction parameters on the yield of levulinic acid were also explored. The results showed that alkali and alkaline earth metal chlorides were not effective in conversion of cellulose, while transition metal chlorides, especially CrCl3, FeCl3 and CuCl2 and a group IIIA metal chloride (AlCl3, exhibited high catalytic activity. The catalytic performance was correlated with the acidity of the reaction system due to the addition of the metal chlorides, but more dependent on the type of metal chloride. Among those metal chlorides, chromium chloride was found to be exceptionally effective for the conversion of cellulose to levulinic acid, affording an optimum yield of 67 mol % after a reaction time of 180 min, at 200 °C, with a catalyst dosage of 0.02 M and substrate concentration of 50 wt %. Chromium metal, most of which was present in its oxide form in the solid sample and only a small part in solution as Cr3+ ion, can be easily separated from the resulting product mixture and recycled. Finally, a plausible reaction scheme for the chromium chloride catalyzed conversion of cellulose in water was proposed.

  7. Surface Chloride Concentration of Concrete under Shallow Immersion Conditions

    Directory of Open Access Journals (Sweden)

    Jun Liu

    2014-09-01

    Full Text Available Deposition of chloride ions in the surface layer of concrete is investigated in this study. In real concrete structure, chloride ions from the service environment can penetrate into concrete and deposit in the surface layer, to form the boundary condition for further diffusion towards the interior. The deposit amount of chloride ions in the surface layer is normally a function of time, rather than a constant. In the experimental investigation, concrete specimens with different mix proportions are immersed in NaCl solution with a mass concentration of 5%, to simulate the shallow immersion condition in sea water, and the surface chloride concentrations are measured at different ages. It is found that the surface chloride concentration increases following the increasing immersion durations, and varies from a weight percentage of 0.161%–0.781% in concretes with different mix proportions. The w/c (water-to-cement ratio influences the surface chloride concentration significantly, and the higher the w/c is, the higher the surface chloride concentration will be, at the same age. However, following the prolonging of immersion duration, the difference in surface chloride concentration induced by w/c becomes smaller and smaller. The incorporation of fly ash leads to higher surface chloride concentration. The phenomena are explained based on pore structure analyses.

  8. Interpretation of postmortem vitreous concentrations of sodium and chloride.

    Science.gov (United States)

    Zilg, B; Alkass, K; Berg, S; Druid, H

    2016-06-01

    Vitreous fluid can be used to analyze sodium and chloride levels in deceased persons, but it remains unclear to what extent such results can be used to diagnose antemortem sodium or chloride imbalances. In this study we present vitreous sodium and chloride levels from more than 3000 cases. We show that vitreous sodium and chloride levels both decrease with approximately 2.2mmol/L per day after death. Since potassium is a well-established marker for postmortem interval (PMI) and easily can be analyzed along with sodium and chloride, we have correlated sodium and chloride levels with the potassium levels and present postmortem reference ranges relative the potassium levels. We found that virtually all cases outside the reference range show signs of antemortem hypo- or hypernatremia. Vitreous sodium or chloride levels can be the only means to diagnose cases of water or salt intoxication, beer potomania or dehydration. We further show that postmortem vitreous sodium and chloride strongly correlate and in practice can be used interchangeably if analysis of one of the ions fails. It has been suggested that vitreous sodium and chloride levels can be used to diagnose drowning or to distinguish saltwater from freshwater drowning. Our results show that in cases of freshwater drowning, vitreous sodium levels are decreased, but that this mainly is an effect of postmortem diffusion between the eye and surrounding water rather than due to the drowning process, since the decrease in sodium levels correlates with immersion time.

  9. Durability of cracked fibre reinforced concrete structures exposed to chlorides

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place; Ekman, Tom; Hansen, Kurt Kielsgaard

    1999-01-01

    is used as environmental load. The chloride penetration is characterized both qualitatively (UV-test) and quantitatively (chloride profile) and by microscopy. The test programme involves three different concrete qualities. Both steel fibres and polypropylene fibres are used in the concrete beams as well......Durability studies are carried out by subjecting FRC-beams to combined mechanical and environmental load. Mechanical load is obtained by exposing beams to 4-point bending until a predefined crack width is reached, using a newly developed test setup. Exposure to a concentrated chloride solution...... as main reinforcement. The effect of the cracks, the fibres and the concrete quality on the chloride penetration is studied....

  10. The DELTA 181 lithium thionyl chloride battery

    Science.gov (United States)

    Sullivan, Ralph M.; Brown, Lawrence E.; Leigh, A. P.

    In 1986, the Johns Hopkins University/Applied Physics Laboratory (JHU/APL) undertook the development of a sensor module for the DELTA 181 spacecraft, a low earth orbit (LEO) mission of less than two months duration. A large lithium thionyl chloride battery was developed as the spacecraft's primary power source, the first known such use for this technology. The exceptionally high energy density of the lithium thionyl chloride cell was the primary driver for its use, resulting in a completed battery with a specific energy density of 120 Wh/lb. Safety requirements became the primary driver shaping all aspects of the power system design and development due to concerns about the potential hazards of this relatively new, high-energy technology. However, the program was completed without incident. The spacecraft was launched on February 8, 1988, from Kennedy Space Center (KSC) with over 60,000 Wh of battery energy. It reentered on April 2, 1988, still operating after 55 days, providing a successful, practical, and visible demonstration of the use of this technology for spacecraft applications.

  11. Regulated trafficking of the CFTR chloride channel.

    Science.gov (United States)

    Kleizen, B; Braakman, I; de Jonge, H R

    2000-08-01

    The cystic fibrosis transmembrane conductance regulator (CFTR), the ABC transporter encoded by the cystic fibrosis gene, is localized in the apical membrane of epithelial cells where it functions as a cyclic AMP-regulated chloride channel and as a regulator of other ion channels and transporters. Whereas a key role of cAMP-dependent phosphorylation in CFTR-channel gating has been firmly established, more recent studies have provided clear evidence for the existence of a second level of cAMP regulation, i.e. the exocytotic recruitment of CFFR to the plasma membrane and its endocytotic retrieval. Regulated trafficking of the CFTR Cl- channel has sofar been demonstrated only in a subset of CFTR-expressing cell types. However, with the introduction of more sensitive methods to measure CFTR cycling and submembrane localization, it might turn out to be a more general phenomenon that could contribute importantly to both the regulation of CFTR-mediated chloride transport itself and to the regulation of other transporters and CFTR-modulated cellular functions. This review aims to summarize the present state of knowledge regarding polarized and regulated CFTR trafficking and endosomal recycling in epithelial cells, to discuss present gaps in our understanding of these processes at the cellular and molecular level, and to consider its possible implications for cystic fibrosis.

  12. Synthesis and structure characterization of diethyldiallylammonium chloride

    Institute of Scientific and Technical Information of China (English)

    刘立华; 龚竹青; 郑雅杰

    2003-01-01

    The unsaturated quaternary ammonium salt diethyldiallylammonium chloride(DEDAAC) was synthesized in a two-step synthetic method. The influences of the adding method of raw materials and temperature on the yields of diethylallylamine (DEAA), and drying and temperature on the synthesis of DEDAAC were investigated. The content of in-process product DEAA was determined by non-aqueous titration. The structure of product DEDAAC was identified with IR, 1 H NMR and elemental analysis. The results show that adding allyl chloride and sodium hydroxide alternately can increase the yield of DEAA and decrease by-products. In further synthesizing of DEDAAC from DEAA, the step of drying DEAA is very necessary. When DEAA is dried by solid sodium hydroxide, good columnar crystals with a high purity(mp 199.5-201.0 ℃) are obtained; when DEAA is undried or the content of water in DEAA is above 20%, only platelets with bad quality are obtained even without crystals. The suitable synthesis conditions for DEAA and DEDAAC are 35 ℃, 6 h and 40 ℃, 36 h, respectively, and their yields are 69.7% and 67.3%, respectively.

  13. Fault locator of an allyl chloride plant

    Directory of Open Access Journals (Sweden)

    Savković-Stevanović Jelenka B.

    2004-01-01

    Full Text Available Process safety analysis, which includes qualitative fault event identification, the relative frequency and event probability functions, as well as consequence analysis, was performed on an allye chloride plant. An event tree for fault diagnosis and cognitive reliability analysis, as well as a troubleshooting system, were developed. Fuzzy inductive reasoning illustrated the advantages compared to crisp inductive reasoning. A qualitative model forecast the future behavior of the system in the case of accident detection and then compared it with the actual measured data. A cognitive model including qualitative and quantitative information by fuzzy logic of the incident scenario was derived as a fault locator for an ally! chloride plant. The obtained results showed the successful application of cognitive dispersion modeling to process safety analysis. A fuzzy inductive reasoner illustrated good performance to discriminate between different types of malfunctions. This fault locator allowed risk analysis and the construction of a fault tolerant system. This study is the first report in the literature showing the cognitive reliability analysis method.

  14. THE COMPATIBILITY OF BLENDS OF POLY(VINYL CHLORIDE) OR CHLORINATED POLY(VINYL CHLORIDE) WITH POLY(METHYL METHACRYLATE)

    Institute of Scientific and Technical Information of China (English)

    WANG Qingguo; CHENG Rongshi

    1988-01-01

    IR spectral shifts of carbonyl vibrational absorption for ethyl acetate, which acts analogically as the structural unit of poly(methyl methacrylate), in cyclohexane, chloroform, chlorinated paraffins, poly(vinyl chloride) and chlorinated poly(vinyl chloride) were measured. The results suggest that there are specific interactions between the carbonyl groups and the chlorinated hydrocarbons which could be responsible for the apparent compatibility of poly(vinyl chloride) -poly(methyl methacrylate) and chlorinated poly(vinyl chloride) -poly(methyl methacrylate) blends. Additionally, the effects of the preparation mode of blend films on phase separation and observed compatibility are discussed.

  15. 21 CFR 177.1980 - Vinyl chloride-propylene copolymers.

    Science.gov (United States)

    2010-04-01

    ... (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: POLYMERS Substances for Use as... applicable to vinyl chloride-propylene copolymers used in food-packaging adhesives complying with § 175.105... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Vinyl chloride-propylene copolymers....

  16. 46 CFR 154.1745 - Vinyl chloride: Transferring operations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Vinyl chloride: Transferring operations. 154.1745 Section 154.1745 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS... Operating Requirements § 154.1745 Vinyl chloride: Transferring operations. A vessel carrying vinyl...

  17. Phosphatase inhibitors activate normal and defective CFTR chloride channels

    OpenAIRE

    Becq, F; Jensen, T J; Chang, X B; Savoia, A.; Rommens, J M; Tsui, L C; Buchwald, M; Riordan, J R; Hanrahan, J W

    1994-01-01

    The cystic fibrosis transmembrane conductance regulator (CFTR) chloride channel is regulated by phosphorylation and dephosphorylation at multiple sites. Although activation by protein kinases has been studied in some detail, the dephosphorylation step has received little attention. This report examines the mechanisms responsible for the dephosphorylation and spontaneous deactivation ("rundown") of CFTR chloride channels excised from transfected Chinese hamster ovary (CHO) and human airway epi...

  18. Experimental and numerical investigation of chloride ingress in cracked concrete

    NARCIS (Netherlands)

    Šavija, B.

    2014-01-01

    Chloride induced corrosion of reinforcing steel is recognized as the most common deterioration mechanism affecting reinforced concrete structures. As such, it has been in focus of research for more than thirty years. Numerous studies of chloride ingress, corrosion initiation, and corrosion propagati

  19. Microwave Mapping Demonstration Using the Thermochromic Cobalt Chloride Equilibrium

    Science.gov (United States)

    Nguyen, Vu D.; Birdwhistell, Kurt R.

    2014-01-01

    An update to the thermochromic cobalt(II) chloride equilibrium demonstration is described. Filter paper that has been saturated with aqueous cobalt(II) chloride is heated for seconds in a microwave oven, producing a color change. The resulting pink and blue map is used to colorfully demonstrate Le Châtelier's principle and to illuminate the…

  20. Hydrophobic treatment of concrete as protection against chloride penetration

    NARCIS (Netherlands)

    Vries, J. de; Polder, R.B.; Borsje, H.

    1996-01-01

    Hydrophobic treatment makes a concrete surface absorb less water and less chloride. Hydrophobic treatment was studied as a protection agninst chloride penetration from deicing salts. Test methods were designed. Nine hydrophobic products were tested, of which three complied to the requirements on fin

  1. Chloride penetration into cementitious mortar at early age

    NARCIS (Netherlands)

    Caballero, J.; Polder, R.B.; Leegwater, G.A.; Fraaij, A.L.A.

    2012-01-01

    Modern service life design methods for concrete structures use chloride diffusion data as an input parameter. Abundant data exist for concrete at 28 days and, to a lesser extent, at later ages. This paper presents chloride diffusion data for mortar at ages between 1 day and 28 days age. Rapid Chlori

  2. Unsteady growth of ammonium chloride dendrites

    Science.gov (United States)

    Martyushev, L. M.; Terentiev, P. S.; Soboleva, A. S.

    2016-02-01

    Growth of ammonium chloride dendrites from aqueous solution is experimentally investigated. The growth rate υ and the radius ρ of curvature of branches are measured as a function of the relative supersaturation Δ for steady and unsteady growth conditions. It is shown that the experimental results are quantitatively described by the dependences ρ=a/Δ+b, υ=cΔ2, where the factors for primary branches are a=(1.3±0.2)·10-7 m, b=(2.5±0.4)·10-7 m, and c=(2.2±0.3)·10-4 m/s. The factor c is found to be approximately 7 times smaller for the side branches than that for the primary branches.

  3. Electrochemical properties of actinides in molten chlorides

    Energy Technology Data Exchange (ETDEWEB)

    Lambertin, D.; Lacquement, J. [CEA/VALRHO - site de Marcoule, Dept. de Recherche en Retraitement et en Vitrification, DRRV, 30 - Marcoule (France); Sanchez, S.; Picard, G. [Ecole Nationale Superieure de Chimie de Paris, Lab. d' Electrochimie et de Chimie Analytique, UMR 7575 du CNRS, 75 - Paris (France)

    2000-07-01

    The chemical properties of plutonium and cerium chlorides have been studied in the fused CaCl{sub 2}-NaCl equimolar mixture at 550 deg. C using a tungsten working electrode and a pO{sup 2-} indicator electrode. The standard potential of Pu(III)/Pu was determined using cyclic voltammetry. The solubility product of Pu{sub 2}O{sub 3} was calculated by potentiometric titration. The standard potential of Ce(III)/Ce have been determined by a potentiometry method. Potentiometric titrations of Ce(III) have been shown the existence of a soluble cerium oxychloride. All these data allowed us to draw the potential-pO{sup 2-} diagram which summarises the properties of plutonium and cerium compounds in the melt. (authors)

  4. [Survey of plasticizers in polyvinyl chloride toys].

    Science.gov (United States)

    Abe, Yutaka; Yamaguchi, Miku; Mutsuga, Motoh; Hirahara, Yoshichika; Kawamura, Yoko

    2012-01-01

    Plasticizers in 101 samples of polyvinyl chloride (PVC) toys on the Japanese market were surveyed. No phthalates were detected in designated toys, though bis(2-ethylhexyl)phthalate, diisononyl phthalate, diisobutyl phthalate, dibutyl phthalate, diisodecyl phthalate and benzyl butyl phthalate were detected in more than half of other toys. 2,2,4-Tributyl-1,3-pentanediol diisobutylate, o-acetyl tributyl citrate, adipates and diacetyl lauroyl glycerol, which are alternative plasticizers to phthalates, were detected. The results of structural analysis confirmed the presence of di(2-ethylhexyl)terephthalate, tributyl citrate, diisononyl 1,2-cyclohexanedicarboxylate and neopentyl glycol esters; these have not previonsly been reported in Japan. There appears to be a shift in plasticizers used for designated toys from phthalates to new plasticizers, and the number of different plasticizers is increasing.

  5. Estimating the chloride transport in cement paste

    Directory of Open Access Journals (Sweden)

    Princigallo, A.

    2012-06-01

    Full Text Available A method was developed to measure the diffusion coefficient of chloride ions in cement paste based on an analytical solution to Fick’s 2nd law in a cylindrical coordinate system. This natural method yielded diffusivity results within as little as a month. Testing time was reduced by exploiting the three-dimensional inward flux in the specimen. In an attempt to determine the saturation concentration, dense portland cement pastes were exposed to a concentrated chloride solution. The method proved to be useful for exploring cement hydration-induced changes in the diffusion coefficient of cement paste.

    Se ha desarrollado un método para medir el coeficiente de difusión de los iones cloruro en la pasta de cemento, partiendo de una aplicación analítica de la segunda ley de Fick en un sistema de coordinadas cilíndrico. Este método, que es natural, demostró ser capaz de producir resultados de difusividad en tan solo un mes. Se consiguió reducir el tiempo de ensayo mediante el aprovechamiento de la tridimensionalidad del flujo desde el exterior al interior de la probeta. A fin de determinar la concentración de saturación, se sometieron las pastas de cemento Portland a una disolución de cloruros concentrada. Este método resultó ser útil en el estudio de los cambios del coeficiente de difusión de la pasta de cemento provocados por las reacciones de hidratación que tienen lugar en esta.

  6. Behavior and products of mechano-chemical dechlorination of polyvinyl chloride and poly (vinylidene chloride).

    Science.gov (United States)

    Xiao, Xiao; Zeng, Zigao; Xiao, Songwen

    2008-02-28

    The mechano-chemical (MC) dechlorination of polyvinyl chloride (PVC) and polyvinylidene chloride (PVDC) was performed by mechanical milling PVC/PVDC powder with zinc powder in a planetary ball mill, and the products of dechlorination were characterized by Infrared spectra (IR), X-ray diffraction (XRD), Raman spectroscopy, gas chromatography-mass spectrometry (GC-MS), and 13C solid-state nuclear magnetic resonance (NMR). The experimental results show that PVC/PVDC can be easily dechlorinated by milling with zinc powder, and formed various kinds of inorganic and organic products. Inorganic compounds included Zn2OCl(2).2H2O, Zn5(OH)8Cl2.H2O etc., and organic products involved diamond-like carbon, carbyne fragment, polyacetylene etc. Organic products formed following the paths of dechlorination, dehydrochlorination, crosslink, and oxidation. The mechano-chemical dechlorination process of PVC/PVDC may be an effective approach for carbyne synthesizing in the appropriate condition.

  7. Effects of cyclic chloride exposure on penetration of concrete cover

    Energy Technology Data Exchange (ETDEWEB)

    Hong, K.; Hooton, R.D.

    1999-09-01

    Concretes are in a state of flux between saturated and partially saturated conditions as they undergo continuous cycles of wetting and drying. In saturated concrete, dissolved ions enter through diffusion, whereas in partially saturated concrete, ion-containing fluids are absorbed by capillary suction and concentrated by evaporation of water. The primary focus of this study was to examine the effects of cyclic wetting and drying with sodium chloride solution on chloride ingress into concrete. Chloride profiles of samples exposed to various lengths and numbers of cycles were determined for three mixtures of concrete: two containing slag and/or silica fume with a 0.4 w/cm (water to cementing materials ratio) and one with a 0.3 w/cm. It was found that longer drying times increase the rate of chloride ingress. A good relationship exists between the depth of chloride penetration and the square root of the number of cycles.

  8. Determination of the heat capacities of Lithium/BCX (bromide chloride in thionyl chloride) batteries

    Science.gov (United States)

    Kubow, Stephen A.; Takeuchi, Kenneth J.; Takeuchi, Esther S.

    1989-12-01

    Heat capacities of twelve different Lithium/BCX (BrCl in thionyl chloride) batteries in sizes AA, C, D, and DD were determined. Procedures and measurement results are reported. The procedure allowed simple, reproducible, and precise determinations of heat capacities of industrially important Lithium/BCX cells, without interfering with performance of the cells. Use of aluminum standards allowed the accuracy of the measurements to be maintained. The measured heat capacities were within 5 percent of calculated heat capacity values.

  9. PHASE EQUILIBRIUM FOR THE TERNARY SYSTEM VINYL CHLORIDE-CHLORINATED POLYETHYLENE-POLY (VINYL CHLORIDE)

    Institute of Scientific and Technical Information of China (English)

    LOU Jianfeng; WENG Zhixue; HUANG Zhiming; PAN Zuren

    1991-01-01

    Swelling capacity of vinyl chloride (VC) in chlorinated polyethylene (CPE) with 25- 40 wt% Cl at temperature 30- 57 ℃ was studied and their relationships were correlated with Langmuir and Freundlich adsorption equations. A ternary phase diagram for VC-CPE-PVC was also established.In-situ polymerization conditions of CPE-g -VC were proposed and CPE content control was analyzed for the manufacturing process of CPE-g-VC graft product based on results of phase equilibrium study.

  10. Genetically encoded optical sensors for monitoring of intracellular chloride and chloride-selective channel activity

    Directory of Open Access Journals (Sweden)

    Piotr Bregestovski

    2009-12-01

    Full Text Available This review briefly discusses the main approaches for monitoring chloride (Cl−, the most abundant physiological anion. Noninvasive monitoring of intracellular Cl− ([Cl−]i is a challenging task owing to two main difficulties: (i the low transmembrane ratio for Cl−, approximately 10:1; and (ii the small driving force for Cl−, as the Cl− reversal potential (ECl is usually close to the resting potential of the cells. Thus, for reliable monitoring of intracellular Cl−, one has to use highly sensitive probes. From several methods for intracellular Cl− analysis, genetically encoded chloride indicators represent the most promising tools. Recent achievements in the development of genetically encoded chloride probes are based on the fact that yellow fluorescent protein (YFP exhibits Cl−-sensitivity. YFP-based probes have been successfully used for quantitative analysis of Cl− transport in different cells and for high-throughput screening of modulators of Cl−-selective channels. Development of a ratiometric genetically encoded probe, Clomeleon, has provided a tool for noninvasive estimation of intracellular Cl− concentrations. While the sensitivity of this protein to Cl− is low (EC50 about 160 mM, it has been successfully used for monitoring intracellular Cl− in different cell types. Recently a CFP–YFP-based probe with a relatively high sensitivity to Cl− (EC50 about 30 mM has been developed. This construct, termed Cl-Sensor, allows ratiometric monitoring using the fluorescence excitation ratio. Of particular interest are genetically encoded probes for monitoring of ion channel distribution and activity. A new molecular probe has been constructed by introducing into the cytoplasmic domain of the Cl−-selective glycine receptor (GlyR channel the CFP–YFP-based Cl-Sensor. This construct, termed BioSensor-GlyR, has been successfully expressed in cell lines. The new genetically encoded chloride probes offer means of screening

  11. Optical, thermal and magnetic studies of pure and cobalt chloride doped L-alanine cadmium chloride

    Science.gov (United States)

    Benila, B. S.; Bright, K. C.; Delphine, S. Mary; Shabu, R.

    2017-03-01

    Single crystals of L-alanine cadmium chloride (LACC) and cobalt chloride (Co2+) doped LACC have been grown by the slow evaporation solution growth technique. The grown crystals were subjected to various characterizations such as powder XRD, SXRD, FTIR, UV-vis, EDAX, TG/DTA, VSM, Dielectric and Second Harmonic Generation (SHG) measurements. The lattice parameters of the grown crystals were determined by single crystal X-ray analysis. EDAX analysis confirms the presence of Co2+ ion in the host material. The functional group and optical behavior of the crystals were identified from FTIR and UV-vis spectrum analysis. Electrical parameters such as dielectric constant, dielectric loss have been studied. The thermal stability of the compound was found out using TGA/DTA analysis. Second Harmonic Generation of the samples was confirmed by Kurtz-Perry powder technique. Magnetic properties of the crystals studied by VSM were also reported. The encouraging results show that the cobalt chloride doped LACC crystals have greater potential applications in optical devices.

  12. Comparative effects of hydrogen chloride gas on tomato and chrysanthemum. I. Distribution and accumulation of chloride following exposure. II. Pathological anatomy of hydrogen chloride gas injury

    Energy Technology Data Exchange (ETDEWEB)

    Shriner, D.S.

    1969-01-01

    Hydrogen chloride (HCl) gas damage to plants has not been a historically important problem. However, recent practices in a number of industries, particularly glass manufacturing and pyrolysis of waste plastics, have increased the seriousness of the problem. Studies were carried out under carefully controlled exposure conditions to determine the effects of HCl gas on a relatively sensitive and a relatively resistant plant species. The macroscopic symptoms of most importance in acute damage to tomato and chrysanthemum are glazing of the lower surface, and a bifacial bronzing of interveinal and marginal areas of leaves. Microscopically, glazing was shown to be caused by a collapse of the lower epidermal cells and a partial disorganization of the spongy mesophyll of leaves. Bronzing was shown to be caused by the further collapse of the spongy mesophyll, and in some cases the palisade mesophyll and upper epidermis. Analysis of plant tissues for their free chloride content following an exposure to HCl gas was done with cell-free water extracts which were titrated on an automatic chloride titrator. On the basis of such studies, evidence suggest that the mechanism of accumulation of chlorides in plants is similar to that of fluorides, and that in subacute doses, chlorides are translocated toward the extremities of the foliar portions of the plant. In areas where a number of different types of pollution sources exist, and symptomotology is not definitive in pinpointing the source, chloride analysis of plant tissues should prove valuable as an aid to diagnosis if HCl gas was suspected.

  13. Acute lethal and teratogenic effects of tributyltin chloride and copper chloride on mahi mahi (Coryphaena hippurus) eggs and larvae.

    Science.gov (United States)

    Adema-Hannes, Rachel; Shenker, Jonathan

    2008-10-01

    Acute and chronic bioassays were used to evaluate the lethal and sublethal effects of copper chloride and tributyltin chloride on mahi mahi (Coryphaena hippurus) embryos, a pelagic life stage often found in the surface microlayer where anthropogenic contaminants can accumulate. Acute bioassay testing determined the median lethal concentration (LC50) for the test organism after 48 h of exposure. Chronic toxicity tests were used to determine the measurement of sublethal parameters, such as developmental abnormalities after 72-h exposures to the toxicants. Embryos were collected 4 h postfertilization and subsequently exposed to 1, 5, 25, 50, and 100 microg/L of copper chloride and 3, 10, 20, 30, and 50 microg/L of tributyltin chloride. Analysis of hatch rate percentage determined that the mean 48-h LC50 of copper chloride and tributyltin chloride was 32.8 and 16.7 microg/L, respectively, based on the pooled data of four experiments with four replicates for each metal. Consistent abnormalities, such as yolk sac swelling, spinal deformities, and decreased hatch rates, were observed for each metal. Teratogenic responses to copper chloride and tributyltin chloride demonstrate the need to investigate further the impacts of pollution in the open oceans to a species indigenous to, and commercially important to, the Florida (USA) coasts. This information could then lead to the future development of a surface microlayer bioassay using mahi mahi embryos.

  14. Chloride penetration into concrete under simulated field conditions

    Energy Technology Data Exchange (ETDEWEB)

    Motohashi, K.; Misra, S.; Yamamoto, A. (Kajima Corp., Tokyo (Japan))

    1991-10-31

    The purpose of this study is to clarify the effect of field conditions such curing period, slump, maximum size of aggregate, etc. on chloride penetration into concrete. With a view to closely simulate the field conditions, all specimens were exposed to chloride attack for five days after casting. From the preliminary results obtained after a six month immersion in 3.3% NaCl solution, higher degrees of chloride ingress were observed in cases when the concrete was prematurely exposed to chloride attack or had a higher slump. In addition, apart from properties, such as water-cement ratio, etc., the relative orientation of the direction of penetration to that of casting, the mortar content of the mix, and the properties of the transition zone between the coarse aggregate and mortar were found to affect the diffusivity of the chloride. Under a limited number of conditions, soluble chloride content was also illustrated in addition to the total chlorides. 10 refs., 6 figs., 6 tabs.

  15. Acetogenic microbial degradation of vinyl chloride

    Science.gov (United States)

    Bradley, P.M.; Chapelle, F.H.

    2000-01-01

    Under methanogenic conditions, microbial degradation of [1,2-14C]vinyl chloride (VC) resulted in significant (14 ?? 3% maximum recovery) but transient recovery of radioactivity as 14C-acetate. Subsequently, 14C- acetate was degraded to 14CH4 and 14CO2 (18 ?? 2% and 54 ?? 3% final recoveries, respectively). In contrast, under 2-bromoethanesulfonic acid (BES) amended conditions, 14C-acetate recovery remained high (27 ?? 1% maximum recovery) throughout the study, no 14CH4 was produced, and the final recovery of 14CO2 was only 35 ?? 4%. These results demonstrate that oxidative acetogenesis may be an important mechanism for anaerobic VC biodegradation. Moreover, these results (1) demonstrate that microbial degradation of VC to CH4 and CO2 may involve oxidative acetogenesis followed by acetotrophic methanogenesis and (2) suggest that oxidative acetogenesis may be the initial step in the net oxidation of VC to CO2 reported previously under Fe(III)-reducing, SO4-reducing, and humic acids- reducing conditions.Under methanogenic conditions, microbial degradation of [1,2-14C]vinyl chloride (VC) resulted in significant (14 ?? 3% maximum recovery) but transient recovery of radioactivity as 14C-acetate. Subsequently, 14C-acetate was degraded to 14CH4 and 14CO2 (18 ?? 2% and 54 ?? 3% final recoveries respectively). In contrast, under 2-bromoethanesulfonic acid (BES) amended conditions, 14C-acetate recovery remained high (27 ?? 1% maximum recovery) throughout the study, no 14CH4 was produced, and the final recovery of 14CO2 was only 35 ?? 4%. These results demonstrate that oxidative acetogenesis may be an important mechanism for anaerobic VC biodegradation. Moreover, these results (1) demonstrate that microbial degradation of VC to CH4 and CO2 may involve oxidative acetogenesis followed by acetotrophic methanogenesis and (2) suggest that oxidative acetogenesis may be the initial step in the net oxidation of VC to CO2 reported previously under Fe(III)-reducing, SO4-reducing, and

  16. Studies on Hypokalemia Induced by Trimethyltin Chloride

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    To determine the possible relationship between plasma potassium concentration and severity of acute trimethyltin chloride (TMT) poisoning and to assess the mechanism of TMT induced hypokalemia. Methods SD rats were treated with various dosages of TMT (ip). All the indices were measured and analysed for determing their possible relations with plasma K+. Results With increase of dosage, the plasma K+ level dropped rapidly, and deaths appeared more quickly. The LDs0 of TMT (ip) was 14.7 mg/kgbw. In the low dosage group (10 mg/kgbw), the plasma K+ level dropped slowly with the lowest dosage on day 6 (4.85 mmol/L). It rose again on day 11 (5.06 mmol/L), and recoverd on day 28. The poisoning signs corresponded with decline of the span of K+ level. The plasma Na+ level dropped half an hour after TMT treatment, but recovered 24 h later. In the high dosage group (46.4 mg/kgbw), the levels of plasma K+ and Na+ fell rapidly within half an hour (P<0.05), the intracellular potassium concentration of RBC did not decrerase obviously (P>0.05), the activities of Na+-K+-ATPase and Mg2+-ATPase in RBC membrane were depressed remarkably (P<0.01, P<0.05, respectively), the plasma aldosterone concentrations rose as high as tenfold (P<0.01), the arterial blood pH fell from 7.434 to 7.258 (P<0.01),pCO2 was raised from 29.62 to 45.33 mmHg (P<0.01). In the 24 h urine test, when rats were treated with TMT (21.5 mg/kgbw, ip), urine volume, urinary potassium, sodium and chloride increased significantly in comparison with those in the controls (P<0.01). Conclusion TMT could induce hypokalemia in SD rats. The available evidence suggests that TMT can induce acute renal leakage of potassium. At the same time, a significant rise of plasma aldosterone may play an important role in promoting potassium leakage from kidney to result in severe hypokalemia with inhaling acid-base abnormalities produced, which aggravate the poisoning symptoms. In the end the rats would die of respiratory

  17. Molten Triazolium Chloride Systems as New Aluminum Battery Electrolytes

    DEFF Research Database (Denmark)

    Vestergaard, B.; Bjerrum, Niels; Petrushina, Irina;

    1993-01-01

    The possibility of using molten mixtures of 1,4-dimethyl-1,2,4-triazolium chloride (DMTC) and aluminum chloride (AlCl3) as secondary battery electrolytes was studied, in some cases extended by the copresence of sodium chloride. DMTC-AlCl, mixtures demonstrated high specific conductivity in a wide...... of milliamperes per square centimeter) was observed at 0.344 V on the acidic sodium tetrachloroaluminate background, involving a free triazolium radical mechanism. Molten DMTC-AlCl3 electrolytes are acceptable for battery performance and both the aluminum anode and the triazolium electrolyte can be used as active...

  18. Calcium chloride in stabilised soil roads and runways

    Directory of Open Access Journals (Sweden)

    Harsh Vardhan

    1952-09-01

    Full Text Available Mudless, dustless, hard and all weather driving surfaces is a serious requirement of the forces.  surfacing by mixtures of definite amounts of locally available stone, gravel, sand, clay and Silt to which calculated amount of calcium chloride is added quickly compact and ultimately harden like concrete. This provides an easy, quick and economic- means of meeting the requirement.  Necessity of such surfaces, use and action of calcium chloride and resulting effects are discussed. Different methods of construction and application of calcium chloride are briefly related.

  19. Microwave evaluation of accelerated chloride ingress in mortar

    Science.gov (United States)

    Hu, C.; Case, T.; Castle, M.; Zoughi, R.; Kurtis, K.

    2001-04-01

    Corrosion of steel in reinforced concrete structures can be induced by the presence of chloride ions near the steel/concrete interface. To show the potential of microwave nondestructive testing techniques for evaluating chloride ingress, 8″×8″×8″ mortar specimens with different mixture designs were prepared. To accelerate chloride ingress, they were exposed to cyclical wet/dry conditions, where the wet condition included exposure to salt bath. A complete discussion of the results will be presented in this paper.

  20. Denitrification of fertilizer wastewater at high chloride concentration

    DEFF Research Database (Denmark)

    Ucisik, Ahmed Süheyl; Henze, Mogens

    Wastewater from fertilizer industry is characterized by high contents of chloride concentration, which normally vary between 60 and 76 g/l. Experiments with bilogical denitrification were performed in lab-scale "fill and draw" reactors with synthetic wastewater with chloride concentrations up to 77.......4 g/l. The results of the experiments showed that biological denitrification was feasible at the extreme environmental conditions prevailing in fertilizer wastewater. Stable continuous biological denitrfication of the synthetic high chloride wastewater was performed up to 77.4 g Cl/l at 37 degree C...

  1. The ionic product of water in concentrated tetramethylammonium chloride solutions.

    Science.gov (United States)

    Sipos, P; Bódi, I; May, P M; Hefter, G T

    1997-04-01

    The ionic product of water, pK(w) = - log[H(+)][OH(-)] has been determined in aqueous solutions of tetramethylammonium chloride over the concentration range of 0.1-5.5 M at 25 degrees C using high-precision glass electrode potentiometric titrations. pK(w) data relating to aqueous potassium and sodium chlorides at ionic strengths up to 5 M are markedly lower than the tetramethylammonium chloride results. These differences are almost certainly due to weak associations between potassium and (especially) sodium and hydroxide ions.

  2. Ionometric determination of chloride ion in circulating and waste waters

    Energy Technology Data Exchange (ETDEWEB)

    Bebeshko, G.I.; Afanas' eva, V.I.; Danielova, I.I.; Dmitriev, M.A.; Radchenko, A.F.

    1986-09-01

    The authors attempt to develop selective ionometric methods to determine chloride ion in waste and circulating waters from technological ore processing, containing significant amounts of sulfide ion and various flotation reagents. These waters contain practically no cations that form hard to dissolve compounds with chloride ion such as Ag/sup +/, Cu/sup +/, Hg/sup +/ or Pb/sup 2 +/. The chloride ion concentration in water varies between 10 and 100 mg/liter. Information is shown on the concentration of the main anions and flotation reagents in waters that were analyzed.

  3. Stochastic Modeling of Reinforced Concrete Structures Exposed to Chloride Attack

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Frier, Christian

    2003-01-01

    concentration and reinforcement cover depth are modeled by stochastic fields. The paper contains a description of the parameters to be included in a stochastic model and a proposal for the information needed to obtain values for the parameters in order to be ab le to perform reliability investigations...... the reinforcement exceeds a critical threshold value. In the present paper a stochastic model is described by which the chloride content in a reinforced concrete structure can be estimated. The chloride ingress is modeled by a 2-dimensional diffusion process and the diffusion coefficient, surface chloride...

  4. Chloride, bromide and iodide scintillators with europium

    Science.gov (United States)

    Zhuravleva, Mariya; Yang, Kan

    2016-09-27

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  5. Piezoresistive Properties of Polyvinyl Chloride Composites

    Science.gov (United States)

    Toprakci, Hatice Aylin Karahan

    Textile based sensors provide an interface between the user and the electronic system by converting any type of physiological or environmental signal into electrical signals. Common applications include health monitoring, rehabilitation, multimedia, and surveillance. In this research we demonstrate fabrication of piezoresistive sensors on textile fabrics through application of a screen-printed conductive nanocomposite layer of plasticized poly(vinyl chloride) (PVC), and carbon nanofiber (CNF). In order to understand the behavior of conductive plastisol, morphological, mechanical and electrical properties of composite films were investigated for different molecular weights of PVC. Homogeneous filler dispersion and good filler/polymer interphase were observed without any dominant filler orientation. Mechanical and electrical properties were found to be affected by CNF, plasticizer content and matrix molecular weight. CNFs were found to provide substantial bridging in the matrix and enhance strength. These nanostructured composite sensors were found to be sensitive under different levels of strain which can be monitored by change in electrical resistance. Finally, we demonstrate the fabrication of piezoresistive sensors on textile fabrics through application of a screen-printed conductive nanocomposite layer of conductive plastisol. Conductive plastisol was found to show good adhesion to fabric with homogeneous CNF distribution. As in composite films, samples were found to show negative piezoresistance at different levels of strain. Strain level and filler concentration were found to affect the piezoresistive behavior and sensitivity of the printed sensors.

  6. Active primary lithium thionyl chloride battery for artillery applications

    Science.gov (United States)

    Baldwin, Arlen R.; Delnick, Frank M.; Miller, David L.

    1990-03-01

    Sandia National Laboratories and Eagle Picher Industries have successfully developed an Active Lithium Thionyl Chloride (ALTC) power battery for unique artillery applications. Details of the design and the results of safety and performance will be presented.

  7. Methyltrioctylammonium chloride catalysed sonochemical synthesis of acridine diones

    Indian Academy of Sciences (India)

    Bhupinder Kaur; Harish Kumar

    2013-09-01

    The greener, clean and efficient protocol for the synthesis of acridine diones derivatives has been achieved by reacting aromatic aldehyde, dimedone and amines using methyltrioctylammonium chloride (Aliquate 336) as a catalyst under ultrasonic irradiations.

  8. 1300-nm gain obtained with dysprosium-doped chloride crystals

    Energy Technology Data Exchange (ETDEWEB)

    Page, R.H.; Schaffers, K.I.; Beach, R.J.; Payne, S.A.; Krupke, W.F.

    1996-03-01

    Dy{sup 3+} - doped chloride crystals have high 1300-nm emission quantum yields. Pump - probe experiments on La Cl{sub 3}:Dy{sup 3+} demonstrate optical gain consistent with predictions based on spectroscopic cross sections and lifetimes.

  9. Probabilistic evaluation of initiation time of chloride-induced corrosion

    Energy Technology Data Exchange (ETDEWEB)

    Val, Dimitri V. [Department of Structural Engineering and Construction Management, Faculty of Civil and Environmental Engineering, Technion, Israel Institute of Technology, Haifa 32000 (Israel)], E-mail: val@tx.technion.ac.il; Trapper, Pavel A. [Department of Structural Engineering and Construction Management, Faculty of Civil and Environmental Engineering, Technion, Israel Institute of Technology, Haifa 32000 (Israel)

    2008-03-15

    The paper presents a model for chloride ingress into concrete. The model accounts for two mechanisms which control the chloride ingress-diffusion and convection. Using one-dimensional (1-D) formulation of the model, the influence of chloride binding and ambient humidity on chloride ingress into concrete has been investigated. Based on results of this investigation parameters for probabilistic analysis have been selected. Probabilistic evaluation of the time to corrosion initiation has then been carried out for a reinforced concrete (RC) wall (1-D problem) and a RC column (2-D problem) in a marine environment. Results of the analysis show that for the same thickness of the concrete cover the probability of corrosion initiation in the corner reinforcing bars of the RC column is much higher than in reinforcing bars in the middle part of the RC wall. The results demonstrate the importance of 2-D modelling for correct prediction of corrosion initiation in such RC elements as columns and beams.

  10. Analysis of chloride diffusivity in concrete containing red mud

    Directory of Open Access Journals (Sweden)

    D.V. Ribeiro

    Full Text Available Red mud is a solid waste produced in the alumina production process and, due to its high pH, is classified as hazardous. Its incorporation in concrete mixtures, acting as filler due to the particles fineness, might be an interesting reuse alternative. The focus of this paper is to study the chloride diffusivity of concrete mixtures containing red-mud. The concentration of chlorides was monitored by measuring the conductivity of the anolyte, which was distilled water initially. In addition, the estimation of the chloride ions diffusion coefficients in steady and non-steady conditions, Ds and Dns, was obtained from the ''time-lag'' and ''equivalent time'' between diffusion and migration experiments. Due to superfine particle-size distribution and the "filler" effect, the red mud addition seems to assure lower chloride diffusivity.

  11. Prediction of chloride ingress and binding in cement paste

    DEFF Research Database (Denmark)

    Geiker, Mette Rica; Nielsen, Erik Pram; Herforth, Duncan

    2007-01-01

    This paper summarizes recent work on an analytical model for predicting the ingress rate of chlorides in cement-based materials. An integral part of this is a thermodynamic model for predicting the phase equilibria in hydrated Portland cement. The model’s ability to predict chloride binding...... in Portland cement pastes at any content of chloride, alkalis, sulfates and carbonate was verified experimentally and found to be equally valid when applied to other data in the literature. The thermodynamic model for predicting the phase equilibria in hydrated Portland cement was introduced into an existing...... Finite Difference Model for the ingress of chlorides into concrete which takes into account its multi-component nature. The “composite theory” was then used to predict the diffusivity of each ion based on the phase assemblage present in the hydrated Portland cement paste. Agreement was found between...

  12. Homocoupling of Aryl Bromides Catalyzed by Nickel Chloride in Pyridine

    Institute of Scientific and Technical Information of China (English)

    TAO, Xiao-Chun; ZHOU, Wei; ZHANG, Yue-Ping; DAI, Chun-ya; SHEN, Dong; HUANG, Mei

    2006-01-01

    Pyridine was used as a solvent for homocoupling of aryl bromides catalyzed by nickel chloride/triarylphosphine in the presence of zinc and recycled easily. Triphenylphosphine was the best ligand for nickel in this coupling reaction.

  13. Chloride supporting electrolytes for all-vanadium redox flow batteries.

    Science.gov (United States)

    Kim, Soowhan; Vijayakumar, M; Wang, Wei; Zhang, Jianlu; Chen, Baowei; Nie, Zimin; Chen, Feng; Hu, Jianzhi; Li, Liyu; Yang, Zhenguo

    2011-10-28

    This paper examines vanadium chloride solutions as electrolytes for an all-vanadium redox flow battery. The chloride solutions were capable of dissolving more than 2.3 M vanadium at varied valence states and remained stable at 0-50 °C. The improved stability appeared due to the formation of a vanadium dinuclear [V(2)O(3)·4H(2)O](4+) or a dinuclear-chloro complex [V(2)O(3)Cl·3H(2)O](3+) in the solutions over a wide temperature range. The all-vanadium redox flow batteries with the chloride electrolytes demonstrated excellent reversibility and fairly high efficiencies. Only negligible, if any, gas evolution was observed. The improved energy capacity and good performance, along with the ease in heat management, would lead to substantial reduction in capital cost and life-cycle cost, making the vanadium chloride redox flow battery a promising candidate for stationary applications.

  14. Facile Preparation of Chloride-Conducting Membranes: First Step towards a Room-Temperature Solid-State Chloride-Ion Battery.

    Science.gov (United States)

    Gschwind, Fabienne; Steinle, Dominik; Sandbeck, Daniel; Schmidt, Celine; von Hauff, Elizabeth

    2016-12-01

    Three types of chloride-conducting membranes based on polyvinyl chloride, commercial gelatin, and polyvinyldifluoride-hexafluoropolymer are introduced in this report. The polymers are mixed with chloride-containing salts, such as tetrabutylammonium chloride, and cast to form membranes. We studied the structural properties, thermal stability, and electrochemical response of the membranes to understand chloride migration and transport. Finally, the membranes are tested in a prototype solid-state chloride-ion battery setup. The feasibility of the membranes for their potential use in anion batteries is discussed.

  15. Durability Analysis of Subway Station in Chloride Environment

    OpenAIRE

    Yang LuFeng; Yu Bo; Hong Bin

    2013-01-01

    In this study, a finite element model for chloride ions transport in saturated concrete was proposed based on the Fick’s second law of diffusion. The governing partial differential equation was solved numerically in space as a boundary-value problem and in time as an initial-value problem by means of the finite element formulations. The maximum allowable value of chloride diffusion coefficient within different locations of subway station with service life of 100a was achieved and suggestions ...

  16. Recovering germanium from coal ash by chlorination with ammonium chloride

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A new process of enriching germanium from coal ash was developed. The process involves in mixing the coal ash and ammonium chloride and then roasting the mixture to produce germanium chloride that is then absorbed by dilute hydrochloric acid and hydrolyzed to germanium oxide. The germanium recovery reached to 80.2% at the optimum condition: mass ratio of NH4Cl/coal ash is 0.15, roasting temperature 400℃ and roasting time 90 min.

  17. Synthesis and structural characterization of polyaniline/cobalt chloride composites

    Science.gov (United States)

    Asha, Goyal, Sneh Lata; Kishore, Nawal

    2016-05-01

    Polyaniline (PANI) and PANI /cobalt chloride composites were synthesized by in situ chemical oxidative polymerization of aniline with CoCl2.6H2O using ammonium peroxidisulphate as an oxidant. These composites were characterized by X-ray diffraction (XRD) and Scanning electron microscopy (SEM). The XRD study reveals that both PANI and composites are amorphous. The XRD and SEM results confirm the presence of cobalt chloride in the composites.

  18. Mechanism of chloride interaction with neurotransmitter:sodium symporters.

    Science.gov (United States)

    Zomot, Elia; Bendahan, Annie; Quick, Matthias; Zhao, Yongfang; Javitch, Jonathan A; Kanner, Baruch I

    2007-10-11

    Neurotransmitter:sodium symporters (NSS) have a critical role in regulating neurotransmission and are targets for psychostimulants, anti-depressants and other drugs. Whereas the non-homologous glutamate transporters mediate chloride conductance, in the eukaryotic NSS chloride is transported together with the neurotransmitter. In contrast, transport by the bacterial NSS family members LeuT, Tyt1 and TnaT is chloride independent. The crystal structure of LeuT reveals an occluded binding pocket containing leucine and two sodium ions, and is highly relevant for the neurotransmitter transporters. However, the precise role of chloride in neurotransmitter transport and the location of its binding site remain elusive. Here we show that introduction of a negatively charged amino acid at or near one of the two putative sodium-binding sites of the GABA (gamma-aminobutyric acid) transporter GAT-1 from rat brain (also called SLC6A1) renders both net flux and exchange of GABA largely chloride independent. In contrast to wild-type GAT-1, a marked stimulation of the rate of net flux, but not of exchange, was observed when the internal pH was lowered. Equivalent mutations introduced in the mouse GABA transporter GAT4 (SLC6A11) and the human dopamine transporter DAT (SLC6A3) also result in chloride-independent transport, whereas the reciprocal mutations in LeuT and Tyt1 render substrate binding and/or uptake by these bacterial NSS chloride dependent. Our data indicate that the negative charge, provided either by chloride or by the transporter itself, is required during binding and translocation of the neurotransmitter, probably to counterbalance the charge of the co-transported sodium ions.

  19. KINETICS OF VINYL CHLORIDE (CO)POLYMERIZATION AT HIGH CONVERSION

    Institute of Scientific and Technical Information of China (English)

    Zu-ren Pan; Zhi-xue Weng; Zhi-ming Huang

    1999-01-01

    This paper provides a summarized review on the kinetics of vinyl chloride homopolymerization in the absence and presence of chain transfer agents, of VC/DAP(diallyl phthalate) copolymerization with chain extension and/or slightly crosslinking functions, and of vinylidene chloride/VC random copolymerization.Models of rate, degree of polymerization or molecular weight, copolymer composition, gel fraction and crosslinking density were proposed and interpreted mechanistically.

  20. cis-Dichloridobis(1,10-phenanthrolinechromium(III chloride

    Directory of Open Access Journals (Sweden)

    Xiaoli Gao

    2011-02-01

    Full Text Available In the title complex, [CrCl2(C12H8N22]Cl, the CrIII ion is situated on a twofold rotation axis and displays a slightly distorted octahedral CrCl2N4 coordination geometry. The Cr environment is composed of a cis arrangement of two 1,10-phenanthroline and two chloride ligands. The chloride counter-anion exhibits half-occupation and is equally disordered over two positions.

  1. Aqueous Chloride Operations Overview: Plutonium and Americium Purification/Recovery

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, Kyle Shelton [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kimball, David Bryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Skidmore, Bradley Evan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-09-28

    These are a set of slides intended for an information session as part of recruiting activities at Brigham Young University. It gives an overview of aqueous chloride operations, specifically on plutonium and americium purification/recovery. This presentation details the steps taken perform these processes, from plutonium size reduction, dissolution, solvent extraction, oxalate precipitation, to calcination. For americium recovery, it details the CLEAR (chloride extraction and actinide recovery) Line, oxalate precipitation and calcination.

  2. Determination of chloride in geological samples by ion chromatography

    Science.gov (United States)

    Wilson, S.A.; Gent, C.A.

    1983-01-01

    Samples of silicate rocks are prepared by sodium carbonate fusion and then treated by ion chromatography. The method was tested for geological standards with chloride concentration between 0.003 and 3%. Observed chloride concentrations comparedd favorably with literature values. The relative standard deviation and detection limit for the method were 8% and 7 ppm, respectively. Up to 30 determination per 24-hour period were possible. ?? 1983.

  3. Hafnium extraction from acidic chloride solutions by Cyanex 923

    Energy Technology Data Exchange (ETDEWEB)

    El-Ammouri, E.; Distin, P.A. [McGill Univ., Montreal (Canada)

    1996-08-01

    Hafnium extraction from hydrochloric acid/lithium chloride solutions into Cyanex 923 in kerosene has been studied. Variables investigated were hydrochloric acid, total chloride and hafnium concentrations in the aqueous phase, and extractant/modifier (isodecanol) levels in the organic phase. Hafnium is considered to load as the tetrachloride complex forming a disolvate with Cyanex 923. Results are compared with equivalent data for zirconium extraction. 14 refs., 7 figs., 2 tabs.

  4. Chlorides behavior in raw fly ash washing experiments

    Energy Technology Data Exchange (ETDEWEB)

    Zhu Fenfen, E-mail: zhu@hse.gcoe.kyoto-u.ac.jp [Department of Urban and Environmental Engineering, Graduate School of Engineering, Katsura Campus, Kyoto University, Nishikyo-ku, Kyoto 615-8540 (Japan); Takaoka, Masaki; Oshita, Kazuyuki [Department of Urban and Environmental Engineering, Graduate School of Engineering, Katsura Campus, Kyoto University, Nishikyo-ku, Kyoto 615-8540 (Japan); Kitajima, Yoshinori; Inada, Yasuhiro [High Energy Accelerator Research Organization (KEK), Institute of Material Structure Science (IMSS), Oho 1-1, Tsukuba, Ibaraki 305-0801 (Japan); Morisawa, Shinsuke; Tsuno, Hiroshi [Department of Urban and Environmental Engineering, Graduate School of Engineering, Katsura Campus, Kyoto University, Nishikyo-ku, Kyoto 615-8540 (Japan)

    2010-06-15

    Chloride in fly ash from municipal solid waste incinerators (MSWIs) is one of the obstructive substances in recycling fly ash as building materials. As a result, we have to understand the behavior of chlorides in recycling process, such as washing. In this study, we used X-ray absorption near edge structure (XANES) and X-ray diffraction (XRD) to study the chloride behavior in washed residue of raw fly ash (RFA). We found that a combination of XRD and XANES, which is to use XRD to identify the situation of some compounds first and then process XANES data, was an effective way to explain the chlorides behavior in washing process. Approximately 15% of the chlorine in RFA was in the form of NaCl, 10% was in the form of KCl, 51% was CaCl{sub 2}, and the remainder was in the form of Friedel's salt. In washing experiments not only the mole percentage but also the amount of soluble chlorides including NaCl, KCl and CaCl{sub 2} decreases quickly with the increase of liquid to solid (L/S) ratio or washing frequency. However, those of insoluble chlorides decrease slower. Moreover, Friedel's salt and its related compound (11CaO.7Al{sub 2}O{sub 3}.CaCl{sub 2}) were reliable standards for the insoluble chlorides in RFA, which are strongly related to CaCl{sub 2}. Washing of RFA promoted the release of insoluble chlorides, most of which were in the form of CaCl{sub 2}.

  5. Intrinsic Resistance of Burkholderia cepacia Complex to Benzalkonium Chloride.

    Science.gov (United States)

    Ahn, Youngbeom; Kim, Jeong Myeong; Kweon, Ohgew; Kim, Seong-Jae; Jones, Richard C; Woodling, Kellie; Gamboa da Costa, Gonçalo; LiPuma, John J; Hussong, David; Marasa, Bernard S; Cerniglia, Carl E

    2016-11-22

    Pharmaceutical products that are contaminated with Burkholderia cepacia complex (BCC) bacteria may pose serious consequences to vulnerable patients. Benzyldimethylalkylammonium chloride (BZK) cationic surfactants are extensively used in medical applications and have been implicated in the coselection of antimicrobial resistance. The ability of BCC to degrade BZK, tetradecyldimethylbenzylammonium chloride (C14BDMA-Cl), dodecyldimethylbenzylammonium chloride (C12BDMA-Cl), decyldimethylbenzylammonium chloride (C10BDMA-Cl), hexyldimethylbenzylammonium chloride, and benzyltrimethylammonium chloride was determined by incubation in 1/10-diluted tryptic soy broth (TSB) to determine if BCC bacteria have the ability to survive and inactivate these disinfectants. With BZK, C14BDMA-Cl, and C12BDMA-Cl, inhibition of the growth of 20 BCC strains was observed in disinfectant solutions that ranged from 64 to 256 µg/ml. The efflux pump inhibitor carbonyl cyanide m-chlorophenylhydrazone increased the sensitivity of bacteria to 64 µg/ml BZK. The 20 BCC strains grew well in 1/10-diluted TSB medium with BZK, C12BDMA-Cl, and C10BDMA-Cl; they absorbed and degraded the compounds in 7 days. Formation of benzyldimethylamine and benzylmethylamine as the initial metabolites suggested that the cleavage of the C alkyl-N bond occurred as the first step of BZK degradation by BCC bacteria. Proteomic data confirmed the observed efflux activity and metabolic inactivation via biodegradation in terms of BZK resistance of BCC bacteria, which suggests that the two main resistance mechanisms are intrinsic and widespread.

  6. Extractive process for preparing high purity magnesium chloride hexahydrate

    Directory of Open Access Journals (Sweden)

    Fezei Radouanne

    2012-01-01

    Full Text Available This paper refers a method for the preparation of magnesium chloride hexahydrate (bischofite from Sebkha el Melah of Zarzis Tunisian natural brine. It is a five-stage process essentially based on crystallization by isothermal evaporation and chemical precipitation. The two first steps were dedicated to the crystallization of sodium chloride and potassiummagnesium double salts, respectively. Then, the resulting liquor was desulfated using calcium chloride solution. After that another isothermal evaporation stage was implemented in order to eliminate potassium ions in the form of carnallite, KCl.MgCl2.6H2O. At the end of this step, the recovered solution primarily composed of magnesium and chloride ions was treated by dioxan in order to precipitate magnesium chloride as MgCl2.6H2O.C4H8O2. This compound dried at constant temperature of 100°C gave good quality magnesium chloride hexahydrate. Besides this salt, the various by-products obtained from the different treatment stages are also useful.

  7. Removal of chloride from electric arc furnace dust.

    Science.gov (United States)

    Chen, Wei-Sheng; Shen, Yun-Hwei; Tsai, Min-Shing; Chang, Fang-Chih

    2011-06-15

    Electric arc furnace (EAF) dust with high chloride content increases the threat of dioxin emissions and the high chloride content reduces the value of recycled zinc oxide produced by EAF dust recycling plants. This study conducts a number of laboratory experiments to determine the technical feasibility of a new dechlorination method. These methods consist of a series of roasting processes and water washing processes. In the roasting process, EAF dust was heated in a tube furnace to evaluate the parameters of atmospheric conditions, roasting temperature, and roasting time. Results indicate that sulfation roasting is more efficient in reducing chloride content than other roasting processes. The water washing process can totally remove water-soluble chloride at a solid to liquid ratio of 1:10. However, the remaining water-insoluble substance is difficult to dechlorinate. For example, lead chloride forms a hydroxyl-halide (PbOHCl) and lead chloride carbonate (Pb(2)CO(3)Cl(2)) agglutinative matrix that is hard to wash away.

  8. Chloride ion transport performance in slag mortar under fatigue loading

    Institute of Scientific and Technical Information of China (English)

    WANG CaiHui; SUN Wei; JIANG JinYang; HAN JianDe; YE BangTu

    2012-01-01

    The transport performance of chloride ion in slag cement mortar was investigated experimentally.In the self-designed experiment,fatigue loading was coupled simultaneously with ion transportation process,the diffusion law of chloride ion was obtained by titration and the AE (acoustic emission) technique was employed to detect the real-time damage distribution in the mortar specimen.The results for fatigue stress levels of 0.3,0.4 and 0.5 and slag contents of 0,10%,30% and 50% showed that fatigue loading accelerated the diffusion of chloride ion in mortar and the acceleration effect increased with the increase in stress levels.Slag addition was found to improve anti-chloride ion erosion performance effectively with the best substitution level at 30%,because the inhibition effect of slag on chloride ion diffusion diminished when the slag content exceeded 30%.The comparative experiments indicated that dynamic load has a significant effect on the transport performance of chloride ion in slag cement mortar.

  9. Aspergilli Response to Benzalkonium Chloride and Novel-Synthesized Fullerenol/Benzalkonium Chloride Nanocomposite.

    Science.gov (United States)

    Unković, Nikola; Ljaljević Grbić, Milica; Stupar, Miloš; Vukojević, Jelena; Janković, Vesna; Jović, Danica; Djordjević, Aleksandar

    2015-01-01

    A comprehensive comparative analysis of antifungal potential of benzalkonium chloride and newly synthesized fullerenol/benzalkonium chloride nanocomposite was conducted to assess the possible impact of carbon-based nanocarrier on antimicrobial properties of the commonly used biocide. Physical characterization of synthesized nanocomposite showed zeta potential of +37.4 mV and inhomogeneous particles size distribution, with nanocomposite particles' dimensions within 30-143 nm and maximum number of particles at 44 nm. The effect of pure and fullerenol nanocarrier-bound biocide was evaluated in eight Aspergillus species. In mycelial growth assay, nanocomposite was more potent, as fungicidal effect of 1.04/0.6 μg mL(-1) was obtained in all but one of the isolates (A. niger), while proportional concentration of pure biocide (0.6 μg mL(-1)) completely inhibited mycelial growth of only three Aspergillus species. However, conidia appear to be less susceptible to nanocomposite treatment, as lower fungistatic (MIC) and fungicidal (MFC) concentrations were obtained with biocide alone (MIC in range from 0.03 to 0.15 μg mL(-1) and MFC from 0.075 to 0.45 μg mL(-1)). To a different degree, both substances stimulated aflatoxin B1 production and inhibited ochratoxin A synthesis. Very low mycelium biomass yield, in range from 1.0 to 3.0 mg dry weight, was documented in both biocide and nanocomposite enriched medium.

  10. Corneal Neurotoxicity Due to Topical Benzalkonium Chloride

    Science.gov (United States)

    Sarkar, Joy; Chaudhary, Shweta; Namavari, Abed; Ozturk, Okan; Chang, Jin-Hong; Yco, Lisette; Sonawane, Snehal; Khanolkar, Vishakha; Hallak, Joelle; Jain, Sandeep

    2012-01-01

    Purpose. The aim of this study was to determine and characterize the effect of topical application of benzalkonium chloride (BAK) on corneal nerves in vivo and in vitro. Methods. Thy1-YFP+ neurofluorescent mouse eyes were treated topically with vehicle or BAK (0.01% or 0.1%). Wide-field stereofluorescence microscopy was performed to sequentially image the treated corneas in vivo every week for 4 weeks, and changes in stromal nerve fiber density (NFD) and aqueous tear production were determined. Whole-mount immunofluorescence staining of corneas was performed with antibodies to axonopathy marker SMI-32. Western immunoblot analyses were performed on trigeminal ganglion and corneal lysates to determine abundance of proteins associated with neurotoxicity and regeneration. Compartmental culture of trigeminal ganglion neurons was performed in Campenot devices to determine whether BAK affects neurite outgrowth. Results. BAK-treated corneas exhibited significantly reduced NFD and aqueous tear production, and increased inflammatory cell infiltration and fluorescein staining at 1 week (P < 0.05). These changes were most significant after 0.1% BAK treatment. The extent of inflammatory cell infiltration in the cornea showed a significant negative correlation with NFD. Sequential in vivo imaging of corneas showed two forms of BAK-induced neurotoxicity: reversible neurotoxicity characterized by axonopathy and recovery, and irreversible neurotoxicity characterized by nerve degeneration and regeneration. Increased abundance of beta III tubulin in corneal lysates confirmed regeneration. A dose-related significant reduction in neurites occurred after BAK addition to compartmental cultures of dissociated trigeminal ganglion cells. Although both BAK doses (0.0001% and 0.001%) reduced nerve fiber length, the reduction was significantly more with the higher dose (P < 0.001). Conclusion. Topical application of BAK to the eye causes corneal neurotoxicity, inflammation, and reduced aqueous

  11. 40 CFR 61.63 - Emission standard for vinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Emission standard for vinyl chloride... for Vinyl Chloride § 61.63 Emission standard for vinyl chloride plants. An owner or operator of a vinyl chloride plant shall comply with the requirements of this section and § 61.65. (a) Vinyl...

  12. DEVELOPMENTAL TOXICITY OF COPPER CHLORIDE, METHYLENE CHLORIDE,AND 6-AMINONICOTINAMIDE TO EMBRYOS OF THE GRASS SHRIMPPALAEMONETES PUGIO

    Science.gov (United States)

    Embryos of estuarine grass shrimp Palaemonetes pugio have demonstrated sensitivity to various solvents and petroleum products, indicating utility for evaluating estuarine contamination. Testing was performed to establish concentration-response curves for methylene chloride, cop...

  13. [Pulmonary manifestations of polyvinyl chloride exposure].

    Science.gov (United States)

    Süyür, Hüseyin; Bayram, Nazan; Aydın, Neriman; Uyar, Meral; Gündoğdu, Nevhiz; Elbek, Osman

    2011-01-01

    There is currently no national data on the effects of polyvinyl chloride (PVC) exposure on pulmonary function. In this study we recruited workers and administrative staff from two PVC plants between July 2008 and July 2009. A questionnaire, pulmonary function tests, carbon monoxide diffusion capacity, and peak flows were recorded. Particulate matter analyses were performed by the Adana Central Laboratory of the Directorate of Occupational Health and Safety. Data were analyzed with SPSS 13.0 software. Nine of the 147 subjects were female. The incidence of a cough was more common in the administrative group. Of the study population, 59.1% were smokers. Tobacco addiction significantly increased cough and dyspnea [OR= 1.10 (1.00-1.20, 95% CI) p= 0.007 and OR= 1.08 (1.02-1.14, 95% CI), p= 0.008, respectively]. Dust exposure was correlated with the incidence of a cough [OR= 0.20 (0.04-0.80, 95% CI) p= 0.008]. The period of work correlated with sputum production [OR= 1.00 (1.00-1.02, 95% CI) p= 0.044]. The FVC% was significantly higher in the administrative group, and FEV1/FVC and DLCO were higher in the exposed group. Tobacco addiction increased the risk of airflow limitation, as evaluated by FEV1/FVC < 70% and FEF25-75 < 50% [OR= 1.15 (1.06-1.25, 95% CI) p= 0.001 and OR= 1.09 (1.02-1.17, 95% CI) p= 0.010, respectively]. Tobacco addiction and increasing duration of work had a negative influence on DLCO in the exposed group (r= -0.270, p= 0.025 and r= -0.210, p= 0.037). In the exposed group PEF variability was significantly greater on workdays, compared with rest days. This study shows that tobacco consumption has a greater affect on the airways than PVC dust exposure. A median of 36 months exposure to PVC dust had no significant impact on pulmonary function parameters, except for DLCO and PEF variability.

  14. Aspergilli Response to Benzalkonium Chloride and Novel-Synthesized Fullerenol/Benzalkonium Chloride Nanocomposite

    Directory of Open Access Journals (Sweden)

    Nikola Unković

    2015-01-01

    Full Text Available A comprehensive comparative analysis of antifungal potential of benzalkonium chloride and newly synthesized fullerenol/benzalkonium chloride nanocomposite was conducted to assess the possible impact of carbon-based nanocarrier on antimicrobial properties of the commonly used biocide. Physical characterization of synthesized nanocomposite showed zeta potential of +37.4 mV and inhomogeneous particles size distribution, with nanocomposite particles’ dimensions within 30–143 nm and maximum number of particles at 44 nm. The effect of pure and fullerenol nanocarrier-bound biocide was evaluated in eight Aspergillus species. In mycelial growth assay, nanocomposite was more potent, as fungicidal effect of 1.04/0.6 μg mL−1 was obtained in all but one of the isolates (A. niger, while proportional concentration of pure biocide (0.6 μg mL−1 completely inhibited mycelial growth of only three Aspergillus species. However, conidia appear to be less susceptible to nanocomposite treatment, as lower fungistatic (MIC and fungicidal (MFC concentrations were obtained with biocide alone (MIC in range from 0.03 to 0.15 μg mL−1 and MFC from 0.075 to 0.45 μg mL−1. To a different degree, both substances stimulated aflatoxin B1 production and inhibited ochratoxin A synthesis. Very low mycelium biomass yield, in range from 1.0 to 3.0 mg dry weight, was documented in both biocide and nanocomposite enriched medium.

  15. Microstructural Evolution of Chloride-Cleaned Silicon Carbide Aluminum Composites

    Science.gov (United States)

    Adeosun, S. O.; Akpan, E. I.; Gbenebor, O. P.; Balogun, S. A.

    2016-02-01

    This study examines the synergy between reinforcement surface modifications on the evolution of microstructures of AA6011-silicon carbide particle (SiCp) composites in multidirectional solidification. Silicon carbide particles (SiCp) were cleaned with ammonium chloride, tin(II) chloride, sodium chloride, and palladium(II) chloride and used as reinforcement to cast AA6011-SiCp composites by applying the stir casting method. A scanning electron microscope and x-ray diffractometer were used to investigate the morphology and phases present, respectively, in the composite material. Results show that wetting agents were effective as they inhibited the formation of Al4C3 in all modified composites. The modified SiCp was found to have varying effects on the morphology, dendrite arm size and direction, size and configuration of AlFeSi, and the amount of eutectic silicon depending on the concentration of the reagent and cleaning time. The highest effect was shown by the use of 40 g/L of tin(II) chloride. The composites had short dendritic arms, good interfacial interaction, and only a few crystals of AlFeSi.

  16. Enhancement of trichothecene production in Fusarium graminearum by cobalt chloride.

    Science.gov (United States)

    Tsuyuki, Rie; Yoshinari, Tomoya; Sakamoto, Naoko; Nagasawa, Hiromichi; Sakuda, Shohei

    2011-03-09

    The effects of cobalt chloride on the production of trichothecene and ergosterol in Fusarium graminearum were examined. Incorporation experiments with (13)C-labeled acetate and leucine confirmed that both 3-acetyldeoxynivalenol and ergosterol were biosynthesized via a mevalonate pathway by the fungus, although hydroxymethyl-glutaryl CoA (HMG-CoA) from intact leucine was able to be partially used for ergosterol production. Addition of cobalt chloride at concentrations of 3-30 μM into liquid culture strongly enhanced 3-acetyldeoxynivalenol production by the fungus, whereas the amount of ergosterol and the mycelial weight of the fungus did not change. The mRNA levels of genes encoding trichothecene biosynthetic proteins (TRI4 and TRI6), ergosterol biosynthetic enzymes (ERG3 and ERG25), and enzymes involved in the mevalonate pathway (HMG-CoA synthase (HMGS) and HMG-CoA reductase (HMGR)) were all strongly up-regulated in the presence of cobalt chloride. Precocene II, a specific trichothecene production inhibitor, suppressed the effects of cobalt chloride on Tri4, Tri6, HMGS, and HMGR, but did not affect erg3 and erg25. These results indicate that cobalt chloride is useful for investigating regulatory mechanisms of trichothecene and ergosterol production in F. graminearum.

  17. Interactions between chloride and cement-paste materials.

    Science.gov (United States)

    Barberon, Fabien; Baroghel-Bouny, Véronique; Zanni, Hélène; Bresson, Bruno; d'Espinose de la Caillerie, Jean-Baptiste; Malosse, Lucie; Gan, Zehong

    2005-02-01

    The durability of cement-based materials with respect to exterior aggressions is one of the current priorities in civil engineering. Depending on their use, the cement-based materials can be exposed to different types of aggressive environments. For instance, damages to concrete structures in contact with a saline environment (sea water on bridges, deicing salts on roads, etc.) are of utmost importance. Upon exposure to saline water, Cl- ions penetrate into the structures and subsequently lead to reinforcement corrosion. Chloride attack is often combined with other aggressive influences such as temperature (e.g., freezing) or the ingress of other ions (e.g., sulfates in sea water). We therefore aim to explore the effect of sodium chloride (NaCl) on the structural chemistry of cement paste. Existing studies about reinforcement corrosion by chloride have focused on the penetration of Cl- ions and the comparison between "free" ions (water-soluble ions) and bound ones. However, little is known about the fixation mechanisms, the localization of Cl in the cement matrix and the structural interaction between Cl and the silicate and aluminate hydrate phases present in cement paste. We present here results of a multinuclear nuclear magnetic resonance study on the fixation of chloride in the hydration products and the characterization of new phases potentially appearing due to chloride ingress.

  18. Development and critical evaluation of fluorescent chloride nanosensors.

    Science.gov (United States)

    Graefe, Anja; Stanca, Sarmiza E; Nietzsche, Sandor; Kubicova, Lenka; Beckert, Rainer; Biskup, Christoph; Mohr, Gerhard J

    2008-09-01

    In this study, we describe the preparation and evaluation of new fluorescent sensor nanoparticles for the ratiometric measurement of chloride concentrations. Both a chloride-sensitive dye (lucigenin) and a reference dye (sulforhodamine derivative) were incorporated into polyacrylamide nanoparticles via inverse microemulsion polymerization and investigated for their response to chloride ions in buffered suspension as well as in living cells. The fluorescence intensity of lucigenin reversibly decreased in the presence of chloride ions due to a collisional quenching process, which can be described with the Stern-Volmer equation. The determined Stern-Volmer constant K SV for the quenching of lucigenin incorporated into particles was found to be 53 M (-1) and is considerably smaller than the Stern-Volmer constant for quenching of free lucigenin ( K SV = 250 M (-1)) under the same conditions. To test the nanosensors in living cells, we incorporated them into Chinese hamster ovary cells and mouse fibroblasts by using the conventional lipofectamin technique and monitored the response to changing chloride concentrations in the cell.

  19. Elusive Presence of Chloride in Mixed Halide Perovskite Solar Cells.

    Science.gov (United States)

    Colella, Silvia; Mosconi, Edoardo; Pellegrino, Giovanna; Alberti, Alessandra; Guerra, Valentino L P; Masi, Sofia; Listorti, Andrea; Rizzo, Aurora; Condorelli, Guglielmo Guido; De Angelis, Filippo; Gigli, Giuseppe

    2014-10-16

    The role of chloride in the MAPbI3-xClx perovskite is still limitedly understood, albeit subjected of much debate. Here, we present a combined angle-resolved X-ray photoelectron spectroscopy (AR-XPS) and first-principles DFT modeling to investigate the MAPbI3-xClx/TiO2 interface. AR-XPS analyses carried out on ad hoc designed bilayers of MAPbI3-xClx perovskite deposited onto a flat TiO2 substrate reveal that the chloride is preferentially located in close proximity to the perovskite/TiO2 interface. DFT calculations indicate the preferential location of chloride at the TiO2 interface compared to the bulk perovskite due to an increased chloride-TiO2 surface affinity. Furthermore, our calculations clearly demonstrate an interfacial chloride-induced band bending, creating a directional "electron funnel" that may improve the charge collection efficiency of the device and possibly affecting also recombination pathways. Our findings represent a step forward to the rationalization of the peculiar properties of mixed halide perovskite, allowing one to further address material and device design issues.

  20. The Chloride Permeability of Persulphated Phosphogypsum-Slag Cement Concrete

    Institute of Scientific and Technical Information of China (English)

    HUANG Youqiang; LU Jianxin; CHEN Feixiang; SHUI Zhonghe

    2016-01-01

    The chloride permeability and microstructure of persulphated phosphogypsum-slag cement concrete (PPSCC), the Portland slag cement concrete (PSCC) and ordinary Portland cement concrete (OPCC) were investigated comparatively. Some test methods were used to evaluate the chloride permeability and explain the relationship between the permeability and microstructure of concrete. The results show that the resistance to chloride penetration in PPSCC is signiifcantly better than that in OPCC, the reasons are as follows: 1) the slag in PPSCC is activated by clinker (alkali activation) and phosphogypsum (sulfate activation), forming more low Ca/Si C-S-H gel and gel pores below 10 nm than OPCC, improving the resistance to chloride penetration; 2) the hydration products of PPSCC have a much stronger binding capacity for chloride ions; and 3) in the same mix proportion, PPSCC has a better workability without large crystals calcium hydroxide in the hydration products, the interfacial transition zone (ITZ) is smoother and denser, which can cut off the communicating pores between the pastes and aggregates.

  1. Chloride channels of platelets%血小板氯通道

    Institute of Scientific and Technical Information of China (English)

    陈晓琳; 尹松梅

    2004-01-01

    Chloride channels distribute widely in the body, and participate in many physiological actions and regulatory processes. Based on their physiological roles and molecular structures, six kinds of chloride channels have been identified: (1) The chloride channels family; (2) Cystic fibrosis transmembrane conductance regulator; (3) Swelling-activated chloride channels; (4) Calcium-activated chloride channels; (5) The p64 (CLIC) gene family; (6) γ-aminobutyric acid and glycine receptors. The chloride channels do exist in platelets, and their appearances are dependent on the presence of intracellular calcium. Blocking agents of chloride channels inhibit the thrombin-activated platelet aggregation and the elevation of the intracellular calcium concentration in a dose-dependent manner. It is suggested that chloride channels play a role in the activation of platelets. In addition, chloride channels act on both the cell volume regulation and the intracellular pH regulation in platelets.

  2. Separating refractory and non-refractory particulate chloride and estimating chloride depletion by aerosol mass spectrometry in a marine environment

    Directory of Open Access Journals (Sweden)

    I. Nuaaman

    2015-01-01

    Full Text Available Aerosol composition and concentration measurements along the coast of California were obtained using an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-AMS onboard the research vessel Atlantis during the CalNex study in 2010. This paper focuses on the measurement of aerosol chloride using the HR-AMS that can be ambiguous in regions with significant quantities of sea salt aerosols. This ambiguity arises due to large differences in the sensitivity of the HR-AMS to refractory chloride species (i.e., NaCl and non refractory chloride species (i.e., NH4Cl, HCl, etc.. Using the HR-AMS, the aerosol chloride signal is typically quantified using ion signals for 35Cl+, H35Cl+, 37Cl+ and H37Cl+ (HxCl+. During this study, the highest aerosol chloride signal was observed during sea sweep experiments when the source of the aerosol chloride was NaCl present in artificially generated sea salt aerosols even though the HR-AMS has significantly lower sensitivity to such refractory species. Other prominent ion signals that arise from NaCl salt were also observed at m/z 22.99 for Na+ and m/z 57.96 for Na35Cl+ during both sea sweep experiments and during periods of ambient measurements. Thus, refractory NaCl contributes significantly to the HxCl+ signal, interfering with attempts to quantify non sea salt chloride (nssCl. It was found that during ambient aerosol measurements, the interference in the HxCl+ signal from sea salt chloride (ssCl was as high as 89%, but with a study wide average of 10%. The Na35Cl+ ion signal was found to be a good tracer for NaCl. We outline a method to establish nssCl in the ambient aerosols by subtracting the sea salt chloride (ssCl signal from the HxCl+ signal. The ssCl signal is derived from the Na35Cl+ ion tracer signal and the HxCl+ to Na35Cl+ ratio established from the sea sweep experiments. Ambient submicron concentrations of ssCl were also established using the

  3. Optimization of the lithium/thionyl chloride battery

    Science.gov (United States)

    White, Ralph E.

    1989-01-01

    A 1-D math model for the lithium/thionyl chloride primary cell is used in conjunction with a parameter estimation technique in order to estimate the electro-kinetic parameters of this electrochemical system. The electro-kinetic parameters include the anodic transfer coefficient and exchange current density of the lithium oxidation, alpha sub a,1 and i sub o,i,ref, the cathodic transfer coefficient and the effective exchange current density of the thionyl chloride reduction, alpha sub c,2 and a sup o i sub o,2,ref, and a morphology parameter, Xi. The parameter estimation is performed on simulated data first in order to gain confidence in the method. Data, reported in the literature, for a high rate discharge of an experimental lithium/thionyl chloride cell is used for an analysis.

  4. Stochastic Models for Chloride-Initiated Corrosion in Reinforced Concrete

    DEFF Research Database (Denmark)

    Engelund, Svend; Sørensen, John Dalsgaard

    Corrosion of the reinforcement in concrete structures can lead to a substantial decrease of the load-bearing capacity. One mode of corrosion initiation is when the chloride content around the reinforcement exceeds a threshold value. In the present paper a statistical model is developed by which t...... the chloride content in a 1reinforced concrete structure can be predicted. The model parameters are estimated on the basis of measurements. The distribution of the time to initiation of corrosion is estimated by FORMISORM-analysis.......Corrosion of the reinforcement in concrete structures can lead to a substantial decrease of the load-bearing capacity. One mode of corrosion initiation is when the chloride content around the reinforcement exceeds a threshold value. In the present paper a statistical model is developed by which...

  5. Binder content influences on chloride ingress in concrete

    Energy Technology Data Exchange (ETDEWEB)

    Dhir, R.K.; Jones, M.R.; McCarthy, M.J. [Univ. of Dundee (United Kingdom)

    1996-12-01

    The reported study looked at the effect of reducing free water contents, and thereby binder contents, and thereby binder contents, on the ingress of chloride in concrete. Concretes with equal water/binder ratio (and design strength), but with water contents reduced by up to 30 liters/m{sup 3}, were tested for chloride diffusion (D) and penetration. The quality of the microstructure was inferred from initial surface absorption tests (ISAT). The results show no practical difference in chloride durability between the corresponding concretes, and that reducing the binder content, (providing that the water/binder ratio is maintained) is not likely to be detrimental. However, the results reported underline the importance of binder type, in this case PFA. Implications of the results are discussed and, in light of the findings, whether specifications which demand minimum cement contents are justified.

  6. Intrinsic Resistance of Burkholderia cepacia Complex to Benzalkonium Chloride

    Directory of Open Access Journals (Sweden)

    Youngbeom Ahn

    2016-11-01

    Full Text Available Pharmaceutical products that are contaminated with Burkholderia cepacia complex (BCC bacteria may pose serious consequences to vulnerable patients. Benzyldimethylalkylammonium chloride (BZK cationic surfactants are extensively used in medical applications and have been implicated in the coselection of antimicrobial resistance. The ability of BCC to degrade BZK, tetradecyldimethylbenzylammonium chloride (C14BDMA-Cl, dodecyldimethylbenzylammonium chloride (C12BDMA-Cl, decyldimethylbenzylammonium chloride (C10BDMA-Cl, hexyldimethylbenzylammonium chloride, and benzyltrimethylammonium chloride was determined by incubation in 1/10-diluted tryptic soy broth (TSB to determine if BCC bacteria have the ability to survive and inactivate these disinfectants. With BZK, C14BDMA-Cl, and C12BDMA-Cl, inhibition of the growth of 20 BCC strains was observed in disinfectant solutions that ranged from 64 to 256 µg/ml. The efflux pump inhibitor carbonyl cyanide m-chlorophenylhydrazone increased the sensitivity of bacteria to 64 µg/ml BZK. The 20 BCC strains grew well in 1/10-diluted TSB medium with BZK, C12BDMA-Cl, and C10BDMA-Cl; they absorbed and degraded the compounds in 7 days. Formation of benzyldimethylamine and benzylmethylamine as the initial metabolites suggested that the cleavage of the C alkyl-N bond occurred as the first step of BZK degradation by BCC bacteria. Proteomic data confirmed the observed efflux activity and metabolic inactivation via biodegradation in terms of BZK resistance of BCC bacteria, which suggests that the two main resistance mechanisms are intrinsic and widespread.

  7. Role of Quercetin in Modulating Chloride Transport in the Intestine

    Science.gov (United States)

    Yu, Bo; Jiang, Yu; Jin, Lingling; Ma, Tonghui; Yang, Hong

    2016-01-01

    Epithelial chloride channels provide the pathways for fluid secretion in the intestine. Cystic fibrosis transmembrane conductance regulator (CFTR) and calcium-activated chloride channels (CaCCs) are the main chloride channels in the luminal membrane of enterocytes. These transmembrane proteins play important roles in many physiological processes. In this study, we have identified a flavonoid quercetin as a modulator of CaCC chloride channel activity. Fluorescence quenching assay showed that quercetin activated Cl− transport in a dose-dependent manner, with EC50 ~37 μM. Short-circuit current analysis confirmed that quercetin activated CaCC-mediated Cl− currents in HT-29 cells that can be abolished by CaCCinh-A01. Ex vivo studies indicated that application of quercetin to mouse ileum and colon on serosal side resulted in activation of CFTR and CaCC-mediated Cl− currents. Notably, we found that quercetin exhibited inhibitory effect against ANO1 chloride channel activity in ANO1-expressing FRT cells and decreased mouse intestinal motility. Quercetin-stimulated short-circuit currents in mouse ileum was multi-component, which included elevation of Ca2+ concentration through L-type calcium channel and activation of basolateral NKCC, Na+/K+-ATPase, and K+ channels. In vivo studies further revealed that quercetin promoted fluid secretion in mouse ileum. The modulatory effect of quercetin on CaCC chloirde channels may therefore represent a potential therapeutic strategy for treating CaCC-related diseases like constipation, secretory diarrhea and hypertension. The inverse effects of quercetin on CaCCs provided evidence that ANO1 and intestinal epithelial CaCCs are different calcium-activated chloride channels. PMID:27932986

  8. Role of quercetin in modulating chloride transport in the intestine

    Directory of Open Access Journals (Sweden)

    Bo Yu

    2016-11-01

    Full Text Available Epithelial chloride channels provide the pathways for fluid secretion in the intestine. Cystic fibrosis transmembrane conductance regulator (CFTR and calcium-activated chloride channels (CaCCs are the main chloride channels in the luminal membrane of enterocytes. These transmembrane proteins play important roles in many physiological processes. In this study, we have identified a flavonoid quercetin as a modulator of CaCC chloride channel activity. Fluorescence quenching assay showed that quercetin activated Clˉ transport in a dose-dependent manner, with EC50 ~37 µM. Short-circuit current analysis confirmed that quercetin activated CaCC-mediated Clˉ currents in HT-29 cells that can be abolished by CaCCinh-A01. Ex-vivo studies indicated that application of quercetin to mouse ileum and colon on serosal side resulted in activation of CFTR and CaCC-mediated Clˉ currents. Notably, we found that quercetin exhibited inhibitory effect against ANO1 chloride channel activity in ANO1-expressing FRT cells and decreased mouse intestinal motility. Quercetin-stimulated short-circuit currents in mouse ileum was multi-component, which included elevation of Ca2+ concentration through L-type calcium channel and activation of basolateral NKCC, Na+/K+-ATPase and K+ channels. In vivo studies further revealed that quercetin promoted fluid secretion in mouse ileum. The modulatory effect of quercetin on CaCC chloirde channels may therefore represent a potential therapeutic strategy for treating CaCC-related diseases like constipation, secretory diarrhea and hypertension. The inverse effects of quercetin on CaCCs provided evidence that ANO1 and intestinal epithelial CaCCs are different calcium-activated chloride channels.

  9. An experiment on multibubble sonoluminescence spectra in sodium chloride solution

    Institute of Scientific and Technical Information of China (English)

    CHEN Zhan; XU JunFeng; HUANG Wei; CHEN WeiZhong; MIAO GuoQing

    2008-01-01

    We investigated experimentally the spectra of MBSL in sodium chloride water solution with krypton as dissolved gas. We observed and compared the spectra of hydroxyl ion at 310 nm and that of sodium atom at 589 nm. It has been found that under the same experimental condition, the intensity of sodium atom spectra is obviously higher than that of the hydroxyl ion spectra, and is more sensitive to the experimental condition. The krypton content, the concentration of sodium chloride solution, and the driving sound pressure obviously affect the spectra intensity in certain range.

  10. Controversy: Is Benzalkonium Chloride Necessary in Antiglaucoma Drops?

    Science.gov (United States)

    Louati, Y

    2012-01-01

    ABSTRACT Medical therapy is the first-line option in glaucoma management, with benzalkonium chloride (BAC) being the most frequently used preservative in antiglaucoma medications. Its use is however, known to be associated with deleterious effects on the ocular surface. This review is an attempt to critically evaluate whether BAC really is indispensable for better bioavailability of antiglaucoma drugs and consequently, better IOP control. How to cite this article: Louati Y, Shaarawy T. Controversy: Is Benzalkonium Chloride Necessary in Antiglaucoma Drops? J Current Glau Prac 2012;6(3):104-107. PMID:26997764

  11. Stochastic Models for Chloride-Initiated Corrosion in Reinforced Concrete

    DEFF Research Database (Denmark)

    Engelund, S.; Sørensen, John Dalsgaard

    1996-01-01

    Corrosion of the reinforcement in concrete structures can lead to a substantial decrease of the load-bearing capacity. One mode of corrosion initiation is when the chloride content around the reinforcement exceeds a threshold value. In the present paper a statistical model is developed by which...... the chloride content in a reinforced concrete structure can be predicted. The model parameters are estimated on the basis of measurements. The distribution of the time to initiation of corrosion is estimated by FORM/SORM-analysis....

  12. Inhibitory effects of beryllium chloride on rat liver microsomal enzymes.

    Science.gov (United States)

    Teixeira, C F; Yasaka, W J; Silva, L F; Oshiro, T T; Oga, S

    1990-04-30

    A single i.v. dose (0.1 mmol Be2+/kg) of beryllium chloride prolonged the duration of pentobarbital-induced sleep and zoxazolamine-induced paralysis, in rats. The effects are correlated with changes of the pharmacokinetic parameters and with the in vitro inhibition of both aliphatic and aromatic hydroxylation of pentobarbital and zoxazolamine. In vitro N-demethylation of meperidine and aminopyrine was partially inhibited while O-demethylation of quinidine was unaffected by liver microsomes of rats pretreated with beryllium salt. The findings give clues that beryllium chloride inhibits some forms of cytochrome P-450, especially those responsible for hydroxylation of substrates, like pentobarbital and zoxazolamine.

  13. Repassivation Potential of Alloy 22 in Sodium and Calcium Chloride Brines

    Energy Technology Data Exchange (ETDEWEB)

    Rebak, R B; Ilevbare, G O; Carranza, R M

    2007-08-11

    A comprehensive matrix of 60 tests was designed to explore the effect of calcium chloride vs. sodium chloride and the ratio R of nitrate concentration over chloride concentration on the repassivation potential of Alloy 22. Tests were conducted using the cyclic potentiodynamic polarization (CPP) technique at 75 C and at 90 C. Results show that at a ratio R of 0.18 and higher nitrate was able to inhibit the crevice corrosion in Alloy 22 induced by chloride. Current results fail to show in a consistent way a different effect on the repassivation potential of Alloy 22 for calcium chloride solutions than for sodium chloride solutions.

  14. Nutritive value of timothy fertilized with chloride or chloride-containing liquid swine manure.

    Science.gov (United States)

    Pelletier, S; Tremblay, G F; Bélanger, G; Chantigny, M H; Seguin, P; Drapeau, R; Allard, G

    2008-02-01

    Chloride fertilization of timothy (Phleum pratense L.) decreases forage dietary cation-anion difference to an acceptable value [(fertilization might affect nutritive value. Two experiments were used to evaluate the effects of chloride fertilization on timothy spring growth and summer regrowth by determining concentrations of crude protein and neutral detergent fiber (NDF), in vitro true digestibility of DM (IVTD), and in vitro digestibility of NDF (dNDF). In an inorganic fertilization experiment, forages grown at 4 locations were fertilized with CaCl(2) (0, 80, 160, and 240 kg of Cl/ha per yr) or NH(4)Cl (160 kg of Cl/ha per yr) in combination with 2 N application rates (70 and 140 kg of N/ha per yr). The increase in Cl fertilization rate affected forage NDF concentration (+1.4%), IVTD (-0.8%), and dNDF (-1.2%) only at the highest rate of N fertilization, but this effect was not of biological importance. Crude protein concentration was not affected by Cl fertilization. Both Cl fertilizer types had a similar impact on forage nutritive value. In an organic fertilization experiment, forages grown at 2 locations received 1 of 7 experimental treatments [unfertilized control, inorganic fertilizer, raw liquid swine manure (LSM), and liquid fractions of 4 pretreated LSM types (decanted, filtered, anaerobically digested, and flocculated)] that provided, respectively, 0, 60, 41, 44, 44, 36, and 101 kg of Cl/ha per yr. The last 6 fertilizer treatments also provided 140 kg of N/ha per yr. The IVTD, dNDF, and concentration of NDF in timothy forage were not affected by the Cl content of the different LSM types. Nitrogen fertilization increased concentration of forage NDF and decreased IVTD and dNDF, but this effect was not biologically important. In both experiments, soil types and harvests had a negligible effect on forage nutritive value. Organic or inorganic Cl fertilizers applied to decrease timothy dietary cation-anion difference have little or no effect on forage nutritive

  15. Mercury toxicity in the shark (Squalus acanthias) rectal gland: apical CFTR chloride channels are inhibited by mercuric chloride.

    Science.gov (United States)

    Ratner, Martha A; Decker, Sarah E; Aller, Stephen G; Weber, Gerhard; Forrest, John N

    2006-03-01

    In the shark rectal gland, basolateral membrane proteins have been suggested as targets for mercury. To examine the membrane polarity of mercury toxicity, we performed experiments in three preparations: isolated perfused rectal glands, primary monolayer cultures of rectal gland epithelial cells, and Xenopus oocytes expressing the shark cystic fibrosis transmembrane conductance regulator (CFTR) chloride channel. In perfused rectal glands we observed: (1) a dose-dependent inhibition by mercury of forskolin/3-isobutyl-1-methylxanthine (IBMX)-stimulated chloride secretion; (2) inhibition was maximal when mercury was added before stimulation with forskolin/IBMX; (3) dithiothrietol (DTT) and glutathione (GSH) completely prevented inhibition of chloride secretion. Short-circuit current (Isc) measurements in monolayers of rectal gland epithelial cells were performed to examine the membrane polarity of this effect. Mercuric chloride inhibited Isc more potently when applied to the solution bathing the apical vs. the basolateral membrane (23 +/- 5% and 68 +/- 5% inhibition at 1 and 10 microM HgCl2 in the apical solution vs. 2 +/- 0.9% and 14 +/- 5% in the basolateral solution). This inhibition was prevented by pre-treatment with apical DTT or GSH; however, only the permeant reducing agent DTT reversed mercury inhibition when added after exposure. When the shark rectal gland CFTR channel was expressed in Xenopus oocytes and chloride conductance was measured by two-electrode voltage clamping, we found that 1 microM HgCl2 inhibited forskolin/IBMX conductance by 69.2 +/- 2.0%. We conclude that in the shark rectal gland, mercury inhibits chloride secretion by interacting with the apical membrane and that CFTR is the likely site of this action.

  16. Toxic effects of mercuric chloride, methylmercuric chloride, and Emisan 6 (an organic mercurial fungicide) on ovarian recrudescence in the catfish

    Energy Technology Data Exchange (ETDEWEB)

    Kirubagaran, R.; Joy, K.P.

    1988-12-01

    Mercurial toxicity in fishes has been focused mainly on tissue uptake and subcellular distribution, nephrotoxicity, development, hatching and survivability of young ones and teratology. Very few studies have been attempted to investigate Hg toxicity on gonadal activity of fishes throughout the breeding season. In a previous investigation the authors have studied the toxic effects of mercuric chloride (HgCl/sub 2/), methylmercuric chloride (CH/sub 3/HgCl) and emisan 6 (an alkoxyalkyl fungicide) on the survival and histology of the kidney of the catfish, Clarias batrachus. The present report deals with toxic effects of these mercurials on ovarian recrudescence in the catfish, an economically important species in the subcontinent.

  17. [Evaluation of professional exposure to chloride vinyl monomer and vinyl idene chloride for a pharmaceutical packaging worker].

    Science.gov (United States)

    Dorsi, F; De Grandis, D; Laurelli, R; Narda, R; Pietrantonio, E; Scarlini, E; Soldati, P S

    2007-01-01

    The study was conducted by Judicial Policy investigations of Prosecution's Office. The event was connected by a professional founded suspicion disease of a pharmaceutical worker. First information coming from the Authority indicated a chloride vinyl monomer (CVM) exposure. We applied a chemical risk assessment method to estimate real professional exposure. The method was based on the productive cycle, physical and chemical and toxicological properties. The method combined to environmental data permitted to formulate etiological hypothesis. The worker during drugs packaging was exposed to CVM and vinylidene chloride (CVDM) caused by blister warming and by glue deposition. We explain the evaluations by which we could consider the pollutant different distribution in workplaces.

  18. The Effect of Silver Chloride Formation on the Kinetics of Silver Dissolution in Chloride Solution

    Science.gov (United States)

    Ha, Hung; Payer, Joe

    2011-01-01

    The precipitation and growth of AgCl on silver in physiological NaCl solution were investigated. AgCl was found to form at bottom of scratches on the surface which may be the less effective sites for diffusion or the favorable sites for heterogeneous nucleation. Patches of silver chloride expanded laterally on the substrate until a continuous film formed. The ionic transport path through this newly formed continuous film was via spaces between AgCl patches. As the film grew, the spaces between AgCl patches closed and ion transport was primarily via micro-channels running through AgCl patches. The decrease of AgCl layer conductivity during film growth were attributed to the clogging of micro-channels or decrease in charge carrier concentration inside the micro-channels. Under thin AgCl layer, i.e. on the order of a micrometer, the dissolution of silver substrate was under mixed activation-Ohmic control. Under thick AgCl layer, i.e. on the order of tens of micrometers, the dissolution of silver substrate was mediated by the Ohmic resistance of AgCl layer. PMID:21516171

  19. The Effect of Silver Chloride Formation on the Kinetics of Silver Dissolution in Chloride Solution.

    Science.gov (United States)

    Ha, Hung; Payer, Joe

    2011-02-28

    The precipitation and growth of AgCl on silver in physiological NaCl solution were investigated. AgCl was found to form at bottom of scratches on the surface which may be the less effective sites for diffusion or the favorable sites for heterogeneous nucleation. Patches of silver chloride expanded laterally on the substrate until a continuous film formed. The ionic transport path through this newly formed continuous film was via spaces between AgCl patches. As the film grew, the spaces between AgCl patches closed and ion transport was primarily via micro-channels running through AgCl patches. The decrease of AgCl layer conductivity during film growth were attributed to the clogging of micro-channels or decrease in charge carrier concentration inside the micro-channels. Under thin AgCl layer, i.e. on the order of a micrometer, the dissolution of silver substrate was under mixed activation-Ohmic control. Under thick AgCl layer, i.e. on the order of tens of micrometers, the dissolution of silver substrate was mediated by the Ohmic resistance of AgCl layer.

  20. Formaldoxime hydrogen bonded complexes with ammonia and hydrogen chloride

    Science.gov (United States)

    Golec, Barbara; Mucha, Małgorzata; Sałdyka, Magdalena; Barnes, Austin; Mielke, Zofia

    2015-02-01

    An infrared spectroscopic and MP2/6-311++G(2d,2p) study of hydrogen bonded complexes of formaldoxime with ammonia and hydrogen chloride trapped in solid argon matrices is reported. Both 1:1 and 1:2 complexes between formaldoxime and ammonia, hydrogen chloride have been identified in the CH2NOH/NH3/Ar, CH2NOH/HCl/Ar matrices, respectively, their structures were determined by comparison of the spectra with the results of calculations. In the 1:1 complexes present in the argon matrices the OH group of formaldoxime acts as a proton donor for ammonia and the nitrogen atom acts as a proton acceptor for hydrogen chloride. In the 1:2 complexes ammonia or hydrogen chloride dimers interact both with the OH group and the nitrogen atom of CH2NOH to form seven membered cyclic structures stabilized by three hydrogen bonds. The theoretical spectra generally agree well with the experimental ones, but they seriously underestimate the shift of the OH stretch for the 1:1 CH2NOH⋯NH3 complex.

  1. Sulfation of Condensed Potassium Chloride by SO2

    DEFF Research Database (Denmark)

    Sengeløv, Louise With; Hansen, Troels Bruun; Bartolomé, Carmen;

    2013-01-01

    The interaction between alkali chloride and sulfur oxides has important implications for deposition and corrosion in combustion of biomass. In the present study, the sulfation of particulate KCl (90–125 μm) by SO2 was studied in a fixed bed reactor in the temperature range 673–1023 K and with rea...

  2. Methyl chloride and other chlorocarbons in polluted air during INDOEX

    NARCIS (Netherlands)

    Scheeren, HA; Lelieveld, J; de Gouw, JA; van der Veen, C; Fischer, H

    2002-01-01

    [1] Methyl chloride (CH3Cl) is the most abundant, natural, chlorine-containing gas in the atmosphere, with oceans and biomass burning as major identified sources. Estimates of global emissions suffer from large uncertainties, mostly for the tropics, partly due to a lack of measurements. We present a

  3. Photonic crystal fiber based chloride chemical sensors for corrosion monitoring

    Science.gov (United States)

    Wei, Heming; Tao, Chuanyi; Krishnaswamy, Sridhar

    2016-04-01

    Corrosion of steel is one of the most important durability issues in reinforced concrete (RC) structures because aggressive ions such as chloride ions permeate concrete and corrode steel, consequently accelerating the destruction of structures, especially in marine environments. There are many practical methods for corrosion monitoring in RC structures, mostly focusing on electrochemical-based sensors for monitoring the chloride ion which is thought as one of the most important factors resulting in steel corrosion. In this work, we report a fiber-optic chloride chemical sensor based on long period gratings inscribed in a photonic crystal fiber (PCF) with a chloride sensitive thin film. Numerical simulation is performed to determine the characteristics and resonance spectral response versus the refractive indices of the analyte solution flowing through into the holes in the PCF. The effective refractive index of the cladding mode of the LPGs changes with variations of the analyte solution concentration, resulting in a shift of the resonance wavelength, hence providing the sensor signal. This fiber-optic chemical sensor has a fast response, is easy to prepare and is not susceptible to electromagnetic environment, and can therefore be of use for structural health monitoring of RC structures subjected to such aggressive environments.

  4. The Vinyl Chloride Problem: Several Routes to One Compound.

    Science.gov (United States)

    Nechvatal, A.; And Others

    This unit is one of a group of units written to fit the Certificate of Sixth Year Studies (CSYS) chemistry course, but it could be used in most Sixth Form courses. These materials are designed for use in a group decision-making format with each of three groups representing a different manufacturing process which produces vinyl chloride. The unit…

  5. Chloride transport in normal and cystic fibrosis epithelial cells

    NARCIS (Netherlands)

    S.M. Kansen (Maarten)

    1992-01-01

    textabstractThe experimental work described in this thesis was aimed at a better understanding of the pathogenesis of CF with the emphasis on electrophysiological studies on Cl" transport. Chloride transport was studied with Ussing chamber, isotopic ('25I")-efflux and fluorescent (SPQ) measurements

  6. Prenatal Mercuric Chloride Exposure Causes Developmental Deficits in Rat Cortex

    Directory of Open Access Journals (Sweden)

    Tayebeh Rastegar

    2011-09-01

    Full Text Available Introduction: Environmental pollution with heavy metals such as mercury is a major health problem. Growing studies on the field have shown the deleterious effects of mercury on human and nonhuman nervous system, especially in infants, however the effects of prenatal exposure to mercuricchloride on cortical development are not yet well understood. The aim of this study was to investigate the effect of prenatal exposure to mercuric chloride on morphological characteristics of brain cortex. Methods: Mercuric chloride (2 mg/kg or normal saline were injected (I.P. to 36 Sprague – dawley rats in the 8th, 9th or 10th day of gestation. The embryos were surgically removed in the 15th day of gestation, and brain cortices were studied by histological techniques. Results: Histological studies showed that embryos of mercuric chloride treated rats hadcortical neuronal disarrangement withdifferent orientations of nuclei, increased diameter of cortex, increased mitosis of cells, increased cell death, decreased cellular density and increased intracellular space. Conclusion: These findings suggest some micro structural abnormalities in cortical regions after prenatal exposure to mercuric chloride. These structural abnormalities may underliesome neurologic disturbances following mercury intoxication.

  7. Autogeneous healing and chloride ingress in cracked concrete

    NARCIS (Netherlands)

    Savija, B.; Schlangen, E.

    2016-01-01

    An experimental study of the influence of autogeneous healing on chloride ingress in cracked concrete is presented. In the study, two concrete mixtures (a Portland cement mix and a blast furnace slag mix), two healing regimes (submerged and fog room regime), two cracking ages (14 and 28 days), and m

  8. Factors other than chloride level influencing rate of reinforcement

    Energy Technology Data Exchange (ETDEWEB)

    Castel, A.; Arliguie, G. [Paul Sabatier Univ., Toulouse (France); Francois, R. [Institut National Des Sciences Appliques, Toulouse (France)

    2000-07-01

    To evaluate the degree of corrosion a 14 year-old concrete member was completely bared and three meter-long beams were stored in three-point flexion in an aggressive environment by sequences of drying and wetting by a salt fog. Total chloride content was measured at the level of all reinforcements. Despite the small concrete cover of 10 mm at the stirrups and 16 mm for the longitudinal reinforcement, no evidence was found to relate corrosion to chloride content, since a large part of the reinforcement was not affected by corrosion. It was concluded that the steel-concrete interface had a major influence on being able to predict the onset of corrosion in relation to chloride content. Indeed, corrosion damage was only present when the steel-concrete interface was damaged. These results call into question the validity of the chloride threshold as the single determining criterion to forecast corrosion development. It is suggested that the nature of the interface between steel and concrete, which may be randomly distributed along the reinforcements, should also be considered. Experimental evidence shows that steel-concrete interface damage is linked to non-elastic behaviour of bond that occurs at a given level of mechanical loading. Therefore, corrosion damage is best considered as a deterministic phenomenon linked to a bonding damage. 25 refs., 2 tabs., 10 figs.

  9. Electrochemical Migration on Electronic Chip Resistors in Chloride Environments

    DEFF Research Database (Denmark)

    Minzari, Daniel; Jellesen, Morten Stendahl; Møller, Per;

    2009-01-01

    Electrochemical migration behavior of end terminals on ceramic chip resistors (CCRs) was studied using a novel experimental setup in varying sodium chloride concentrations from 0 to 1000 ppm. The chip resistor used for the investigation was 10-kΩ CCR size 0805 with end terminals made of 97Sn3Pb...

  10. Aqueous Chloride Operations Overview: Plutonium and Americium Purification/Recovery

    Energy Technology Data Exchange (ETDEWEB)

    Kimball, David Bryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Skidmore, Bradley Evan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-06-22

    Acqueous Chloride mission is to recover plutonium and americium from pyrochemical residues (undesirable form for utilization and storage) and generate plutonium oxide and americium oxide. Plutonium oxide is recycled into Pu metal production flowsheet. It is suitable for storage. Americium oxide is a valuable product, sold through the DOE-OS isotope sales program.

  11. Contact dermatitis in workers processing polyvinyl chloride plastics.

    Science.gov (United States)

    Vidović, R; Kansky, A

    1985-01-01

    Out of 401 workers employed in a factory producing shoes from polyvinyl chloride (PVC) granulate, 388 were investigated. By patch testing with the standard tests and 4 phthalate compounds, a diagnosis of allergic contact dermatitis was confirmed in 11 of these. Six of them were sensitized to phthalates and 5 to coal tar.

  12. Study on the Reaction Mechanism of Naphthalene with Oxalyl Chloride

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The reaction of naphthalene with oxalyl chloride in the presence of anhydrous AlCl3 was investigated. The homolog of dinaphthyl methanone can be obtained mainly from this reaction. Naphthalene conversion does not have evident correlation with the amount of AlCl3. The results show that the reaction proceeds via carbon cation electrophilic substitution reaction-free radical substitution reaction pathway.

  13. 21 CFR 522.1862 - Sterile pralidoxime chloride.

    Science.gov (United States)

    2010-04-01

    ...) Conditions of use. (1) It is used in horses, dogs, and cats as an antidote in the treatment of poisoning due to those pesticides and chemicals of the organophosphate class which have anticholinesterase activity... for at least 48 hours. Following severe poisoning, a second dose of sterile pralidoxime chloride...

  14. Comment on "Local impermeant anions establish the neuronal chloride concentration".

    Science.gov (United States)

    Voipio, Juha; Boron, Walter F; Jones, Stephen W; Hopfer, Ulrich; Payne, John A; Kaila, Kai

    2014-09-05

    Glykys et al. (Reports, 7 February 2014, p. 670) conclude that, rather than ion transporters, "local impermeant anions establish the neuronal chloride concentration" and thereby determine "the magnitude and direction of GABAAR currents at individual synapses." If this were possible, perpetual ion-motion machines could be constructed. The authors' conclusions conflict with basic thermodynamic principles.

  15. Methylene chloride: two-generation inhalation reproductive study in rats

    Energy Technology Data Exchange (ETDEWEB)

    Nitschke, K.D.; Eisenbrandt, D.L.; Lomax, L.G.; Rao, K.S.

    1988-07-01

    Reproductive parameters in Fischer 344 rats were evaluated following inhalation of methylene chloride (MeCl/sub 2/) for two successive generations. Thirty male and female rats were exposed to 0, 100, 500, or 1500 ppm MeCl/sub 2/ for 6 hr/day, 5 days/week for 14 weeks and then mated to produce f1 litters. After weaning, 30 randomly selected f1 pups/sex/group were exposed to MeCl/sub 2/ for 17 weeks and subsequently mated to produce f2 litters. Reproductive parameters examined included fertility, litter size and neonatal growth, and survival. All adults and selected weanlings were examined for grossly visible lesions. Tissues from selected weanlings were examined histopathologically. No adverse effects on reproductive parameters, neonatal survival, or neonatal growth were noted in animals exposed to methylene chloride in either the f0 or f1 generations. Similarly, there were no treatment-related gross pathologic observations in f0 or f1 adults or f1 and f2 weanlings. Histopathologic examination of tissues from f1 and f2 weanlings did not reveal any lesions attributed to methylene chloride. Thus, exposure of rats to concentrations as high as 1500 ppm methylene chloride, which has been shown in a 2-year study to produce treatment-related effects, did not affect any reproductive parameters.

  16. Maintenance Planning for Chloride Initiated Corrosion in Concrete Structures

    DEFF Research Database (Denmark)

    Engelund, S.; Sørensen, John Dalsgaard

    1998-01-01

    Corrosion of the reinforcement in concrete structures can be initiated when the chloride concentration around the reinforcement exceeds a threshold value. In order to prevent the corrosion from reaching a stage where the load-bearing capacity of a given structure suffers a substantial decrease...

  17. Using polyvinyl chloride dyed with bromocresol purple in radiation dosimetry.

    Science.gov (United States)

    Kattan, Munzer; al Kassiri, Haroun; Daher, Yarob

    2011-02-01

    Polyvinyl chloride (PVC) dyed with bromocresol purple was investigated as a high-dose radiation dosimeter. The absorbance at 417 nm depends linearly on the dose below 50 kGy. The response depends neither on dose rate nor on the irradiation temperature. The effects of post-irradiation storage in the dark and in indirect sunlight are also discussed.

  18. 21 CFR 862.1170 - Chloride test system.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Chloride test system. 862.1170 Section 862.1170 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Chemistry Test Systems §...

  19. Chloride Ingress in Concrete Cracks under Cyclic Loading

    DEFF Research Database (Denmark)

    Küter, André; Geiker, Mette Rica; Olesen, John Forbes;

    2005-01-01

    was similar for both sets and the maximum crack width was kept constant throughout the exposure period by means of precracking and an external prestressed reinforcement. Chloride profiles after 40 days revealed a considerable increase in ingress towards the crack tip in contrast to data from the literature...

  20. Synthesis of functional aromatic multisulfonyl chlorides and their masked precursors.

    Science.gov (United States)

    Percec, V; Bera, T K; De, B B; Sanai, Y; Smith, J; Holerca, M N; Barboiu, B; Grubbs, R B; Fréchet, J M

    2001-03-23

    The synthesis of functional aromatic bis(sulfonyl chlorides) containing an acetophenone and two sulfonyl chloride groups, i.e., 3,5-bis[4-(chlorosulfonyl)phenyl]-1-acetophenone (16), 3,5-bis(chlorosulfonyl)-1-acetophenone (17), and 3,5-bis(4-(chlorosulfonyl)phenyloxy)-1-acetophenone (18) via a sequence of reactions, involving in the last step the quantitative oxidative chlorination of S-(aryl)- N,N'-diethylthiocarbamate, alkyl- or benzyl thiophenyl groups as masked nonreactive precursors to sulfonyl chlorides is described. A related sequence of reactions was used for the synthesis of the aromatic trisulfonyl chloride 1,1,1-tris(4-chlorosulfonylphenyl)ethane (24). 4-(Chlorosulfonyl)phenoxyacetic acid, 2,2-bis[[[4-(chlorosulfonyl)phenoxyacetyl]oxy]methyl]-1,3-propanediyl ester (27), 5,11,17,23-tetrakis(chlorosulfonyl)-25,26,27,28-tetrakis(ethoxycarbonylmethoxy)calix[4]arene (38), 5,11,17,23,29,35-hexakis(chlorosulfonyl)-37,38,39,40,41,42-hexakis(ethoxycarbonylmethoxy)calix[6]arene (39), 5,11,17,23,29,35,41,47-octakis(chlorosulfonyl)-49,50,51,52,53,54,55,56-octakis(ethoxycarbonylmethoxy)calix[8]arene (40), 5,11,17,23-tetrakis(tert-butyl)-25,26,27,28-tetrakis(chlorosulfonyl phenoxyacetoxy)calix[4]arene (44), 5,11,17,23,29,35-hexakis(tert-butyl)-37,38,39,40,41,42-hexakis(chlorosulfonylphenoxyacetoxy)calix[6]arene (45), and 5,11,17,23,29,35,41,47-octakis(tert-butyl)-49,40,51,52,53,54,55,56-octakis(chlorosulfonylphenoxyacetoxy)calix[8]arene (46) were synthesized by two different multistep reaction procedures, the last step of both methods consisting of the chlorosulfonation of compounds containing suitable activated aromatic positions. 2,4,6-Tris(chlorosulfonyl)aniline (47) was obtained by the chlorosulfonation of aniline. The conformation of two series of multisulfonyl chlorides i.e., 38, 39, 40 and 44, 45, 46, was investigated by (1)H NMR spectroscopy. The masked nonreactive precursor states of the functional aromatic multisulfonyl chlorides and the aromatic

  1. Effects of Organic Corrosion Inhibitor and Chloride Ion Concentration on Steel Depassivation and Repassivation in Solution

    Institute of Scientific and Technical Information of China (English)

    WANG; Zixiao; YU; Lei; LIU; Zhiyong; SONG; Ning

    2015-01-01

    Effect of an organic corrosion inhibitor(OCI) named PCI-2014 added in chloride solution on the critical chloride concentration of mild steel depassivation and the critical OCI concentrations for repairing the steel in different chloride solution were investigated.The results show that the critical chloride concentration increases exponentially with raises of PCI-2014 concentration in the solution.Within a certain chloride ion concentration range,the critical PCI-2014 concentration for repairing the corroded steel is also increases exponentially with enhancement of chloride content in the solution.Atomic force microscopy images display the molecular particles of inhibitor are adsorbed on the steel surface and formed a protective layer.Analysis of X-ray photoelectron spectroscopy shows the chloride ions at the surface of steel are displaced by atoms or molecules of the inhibitor in chloride condition.

  2. Covalent organic polymer functionalization of activated carbon surfaces through acyl chloride for environmental clean-up

    DEFF Research Database (Denmark)

    Mines, Paul D.; Thirion, Damien; Uthuppu, Basil;

    2017-01-01

    Nanoporous networks of covalent organic polymers (COPs) are successfully grafted on the surfaces of activated carbons, through a series of surface modification techniques, including acyl chloride formation by thionyl chloride. Hybrid composites of activated carbon functionalized with COPs exhibit...

  3. Effects of Organic Corrosion Inhibitor and Chloride Ion Concentration on Steel Depassivation and Repassivation in Solution

    Institute of Scientific and Technical Information of China (English)

    WANG Zixiao; YU Lei; LIU Zhiyong; SONG Ning

    2015-01-01

    Effect of an organic corrosion inhibitor (OCI) named PCI-2014 added in chloride solution on the critical chlo-ride concentration of mild steel depassivation and the critical OCI concentrations for repairing the steel in different chlo-ride solution were investigated. The results show that the critical chloride concentration increases exponentially with raises of PCI-2014 concentration in the solution. Within a certain chloride ion concentration range, the critical PCI-2014 concentration for repairing the corroded steel is also increases exponentially with enhancement of chloride content in the solution. Atomic force microscopy images display the molecular particles of inhibitor are adsorbed on the steel surface and formed a protective layer. Analysis of X-ray photoelectron spectroscopy shows the chloride ions at the surface of steel are displaced by atoms or molecules of the inhibitor in chloride condition.

  4. [Effect of sodium chloride on elasticity of silicone matrices].

    Science.gov (United States)

    Snejdrová, E; Zelenka, J; Rehula, M

    2002-09-01

    An increase in the availability of the active ingredient from silicone matrices can be achieved by using sodium chloride as the filler. An addition of sodium chloride also influences the mechanical properties of silicone systems. The temperature dependence of real Young's model E' of addition silicone systems with sodium chloride was measured. With increasing NaCl concentration in the silicone system, the values of Young's module E are increased. The increase is also influenced by the particle size of NaCl. The values of the module are moderately increased also with increasing temperature, which corresponds to the kinetic theory of caoutchouc elasticity. A significant increase in E takes place at NaCl concentrations higher than 20%. With a 50% NaCl content in the system, E is increased approximately 3.5 times in comparison with an unfilled sample. Various theories of elastic behaviour of composites can be employed for the description of the effect of the filler on the mechanical properties of silicone systems under small deformations. The effect of chloride is best described by the relation proposed by Nielsen. The value of the constant A in Nielsen's relation, dependent on the shape of the filler particles and Poisson's constant of the unfilled matrix, decreases with increasing particle size. With a change in particle size, a certain change in particle shape takes place. Hydrodynamic theory provides good results for sodium chloride particle size of 102.5 microns, but for particle sizes of 20 microns and 60 microns it is less successful than Nielsen's relation.

  5. AMELIORATION OF MERCURIC CHLORIDE INDUCED NEPHROTOXICITY AND OXIDATIVE STRESS BY GARLIC EXTRACT

    OpenAIRE

    Abirami, N; Jagadeeswari, R.

    2006-01-01

    Effect of Garlic against mercuric chloride induced toxicity in albino rats was studied. Oral administration of mercuric chloride (100mg/kg/p.o) for 30 days resulted in significant increase in LPO Basal level and LPO FeSO4 induced and significant decrease in GSH (Glutathione) and Vit C as compared to the normal and control group. Simultaneous administration of Garlic along with Mercuric chloride, produced a pronounced neproprotective effect against mercuric chloride induced toxicity in rats by...

  6. The Influence of Mineral Functional Materials on Chloride Ion Penetration of Concrete

    Institute of Scientific and Technical Information of China (English)

    HU Hongmei; MA Baoguo

    2005-01-01

    The mechanism of chloride ion penetration in high performance concrete was analyzed. The experimental results indicate that there are two important reasons that influence the anti-chloride penetration of high performance concrete. One is the function effect of mineral functional material, so that it increases concrete's capability to resist chloride ion penetration. The other is combined action of mineral functional material's original capability of binding the chloride ion (physical adsorption) and physicochemical adsorption after hydration.

  7. Solubilities ,Densities and Refractive Indices of Rubidium Chloride or Cesium Chloride in Ethanol Aqueous Solutions at Different Temperatures

    Institute of Scientific and Technical Information of China (English)

    ZHAO,Wen-Xia; HU,Man-Cheng; JIANG,Yu-Cheng; LI,Shu-Ni

    2007-01-01

    The data of solubilities.densities and refractive indices of rubidium chloride or cesium chloride in the system C2H5OH-H2O were measured by using a simple accurate analytical method at different temperatures,with mass fractions of ethanol in the range of O to 1.0.In all cases,the presence of ethanol significantly reduced the solubility of rubidium chloride and cesium chloride in aqueous solution.The solubilities of the saturated solutions were fitted via polynomial equations as a function of the mass fraction of ethanol.The CsCl-C2H5OH-H2O temary system appeared in two liquid phases:alcoholic phase and water phase.when the mass fractions of ethanol were in the range of 10.37% to 49.59%at 35℃.Density and refractive index were also determined for the same ternary systems with varied unsaturated salt concentrations.Values for both experiment and theory were correlated with the salt concentrations and proportions of alcohol in the solutions.The equations proposed could also account for the saturated solutions.

  8. separation of strontium and cesium from ternary and quaternary lithium chloride-potassium chloride salts via melt crystallization

    Directory of Open Access Journals (Sweden)

    Ammon N. Williams

    2015-12-01

    Full Text Available Separation of cesium chloride (CsCl and strontium chloride (SrCl2 from the lithium chloride-potassium chloride (LiCl-KCl salt was studied using a melt crystallization process similar to the reverse vertical Bridgeman growth technique. A ternary SrCl2-LiCl-KCl salt was explored at similar growth rates (1.8–5 mm/h and compared with CsCl ternary results to identify similarities. Quaternary experiments were also conducted and compared with the ternary cases to identify trends and possible limitations to the separations process. In the ternary case, as much as 68% of the total salt could be recycled per batch process. In the quaternary experiments, separation of Cs and Sr was nearly identical at the slower rates; however, as the growth rate increased, SrCl2 separated more easily than CsCl. The quaternary results show less separation and rate dependence than in both ternary cases. As an estimated result, only 51% of the total salt could be recycled per batch. Furthermore, two models have been explored to further understand the growth process and separation. A comparison of the experimental and modeling results reveals that the nonmixed model fits reasonably well with the ternary and quaternary data sets. A dimensional analysis was performed and a correlation was identified to semipredict the segregation coefficient.

  9. The Limiting Phenomena at the Anode of the Electrowinning of Zinc from Zinc Chloride in a Molten Chloride Electrolyte

    NARCIS (Netherlands)

    Lans, S.C.

    2004-01-01

    The objective of this research is to investigate the possibilities and technological viability for the electrowinning of zinc from zinc chloride. This research contributes to development of an alternative process, because it provides: ⢠A clear understanding and overview of the present zinc industr

  10. High Energy Density Battery Lithium Thionyl Chloride Improved Reverse Voltage Design.

    Science.gov (United States)

    1981-12-01

    BATTERY LITHIUM THIONYL CHLORIDE IMPROVED R-ETC(U) DEC 81 A E ZOLLA N660011-C-0310...HIGH ENERGY DENSITY BATTERY LITHIUM THIONYL CHLORIDE IMPROVED REVERSE VOLTAGE DESIGN Dr. A. E. Zolla Altus Corporation C:1 1610 Crane Court San Jose...reverse aide If necesary and identify by block number) Lithium Battery Lithium Thionyl Chloride High Energy Density Battery Voltage Reversal Battery

  11. 21 CFR 520.310 - Caramiphen ethanedisulfonate and ammonium chloride tablets.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Caramiphen ethanedisulfonate and ammonium chloride... § 520.310 Caramiphen ethanedisulfonate and ammonium chloride tablets. (a) Specifications. Each tablet contains 10 milligrams of 5st caramiphen ethanedisulfonate and 80 milligrams of ammonium chloride.1 1...

  12. 40 CFR 415.240 - Applicability; description of the ammonium chloride production subcategory.

    Science.gov (United States)

    2010-07-01

    ... ammonium chloride production subcategory. 415.240 Section 415.240 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Ammonium Chloride Production Subcategory § 415.240 Applicability; description of the ammonium chloride production subcategory. The provisions of this subpart are applicable to...

  13. 46 CFR 154.1750 - Butadiene or vinyl chloride: Refrigeration system.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Butadiene or vinyl chloride: Refrigeration system. 154... and Operating Requirements § 154.1750 Butadiene or vinyl chloride: Refrigeration system. A refrigeration system for butadiene or vinyl chloride must not use vapor compression unless it: (a) Avoids...

  14. Determination of Vinyl Chloride at ug/l. Level in Water by Gas Chromatography

    Science.gov (United States)

    Bellar, Thomas A.; And Others

    1976-01-01

    A quantitative method for the determination of vinyl chloride in water is presented. Vinyl chloride is transfered to the gas phase by bubbling inert gas through the water. After concentration on silica gel or Carbosieve-B, determination is by gas chromatography. Confirmation of vinyl chloride is by gas chromatography-mass spectrometry. (Author/BT)

  15. 21 CFR 177.1960 - Vinyl chloride-hexene-1 copolymers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Vinyl chloride-hexene-1 copolymers. 177.1960... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1960 Vinyl chloride-hexene-1 copolymers. The vinyl chloride-hexene-1 copolymers identified in paragraph (a) of this section or...

  16. 21 CFR 177.1970 - Vinyl chloride-lauryl vinyl ether copolymers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Vinyl chloride-lauryl vinyl ether copolymers. 177... for Use as Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1970 Vinyl chloride-lauryl vinyl ether copolymers. The vinyl chloride-lauryl vinyl ether copolymers identified in...

  17. 21 CFR 178.2650 - Organotin stabilizers in vinyl chloride plastics.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Organotin stabilizers in vinyl chloride plastics... AIDS, AND SANITIZERS Antioxidants and Stabilizers § 178.2650 Organotin stabilizers in vinyl chloride... vinyl chloride homopolymers and copolymers complying with the provisions of § 177.1950 or § 177.1980...

  18. The Influence of C3A Content in Cement on the Chloride Transport

    Directory of Open Access Journals (Sweden)

    Min Jae Kim

    2016-01-01

    Full Text Available The present study concerns the influence of C3A in cement on chloride transport in reinforced concrete. Three modified cement was manufactured in the variation of the C3A content, ranging from 6.0 and 10.5 up to 16.9%. The setting time of fresh concrete was measured immediately after mixing, together with the temperature at the time of initial set. For properties of hardened concrete in the variation in the C3A, a development of the compressive strength and chloride permeation were measured using mortar specimens. Simultaneously, chloride binding capacity was measured by the water extraction method. To ensure the influence of pore structure on chloride transport, the pore structure was examined by the mercury intrusion porosimetry. As a result, it was found that an increase in the C3A content resulted in an increase in chloride binding capacity. However, it seemed that increased binding of chlorides is related to the higher ingress of chlorides, despite denser pore structure. It may be attributed to the higher surface chloride, which could increase the gradient of chloride concentration from the surface, thereby leading to the higher level of chloride profiles. Substantially, the benefit of high C3A in resisting corrosion, arising from removal of free chlorides in the pore solution, would be offset by increased chloride ingress at a given duration, when it comes to the corrosion-free service life.

  19. 75 FR 36629 - Barium Chloride From the People's Republic of China: Continuation of Antidumping Duty Order

    Science.gov (United States)

    2010-06-28

    ... International Trade Administration Barium Chloride From the People's Republic of China: Continuation of... China: Final Results of Expedited Third Sunset Review of Antidumping Duty Order, 74 FR 55814 (October 29... Barium Chloride From China, 75 FR 33824 (June 15, 2010), and Barium Chloride from China (Inv. No....

  20. 76 FR 30604 - National Emission Standards for Hazardous Air Pollutants for Polyvinyl Chloride and Copolymers...

    Science.gov (United States)

    2011-05-26

    ... Polyvinyl Chloride and Copolymers Production AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed..., the proposed rule, National Emission Standards for Hazardous Air Pollutants for Polyvinyl Chloride and... Polyvinyl Chloride and Copolymers Production, under Docket ID No. EPA-HQ-OAR-2002-0037 (available at...

  1. 76 FR 42613 - National Emission Standards for Hazardous Air Pollutants for Polyvinyl Chloride and Copolymers...

    Science.gov (United States)

    2011-07-19

    ... Polyvinyl Chloride and Copolymers Production; Extension of Comment Period AGENCY: Environmental Protection... for Hazardous Air Pollutants for Polyvinyl Chloride and Copolymers Production is being extended for 14... extend the public comment period for the May 20, 2011, Proposed Polyvinyl Chloride and...

  2. Connecting to concrete: wireless monitoring of chloride ions in concrete structures

    NARCIS (Netherlands)

    Abbas, Yawar; Have, ten Bas; Hoekstra, Gerrit I.; Douma, Arjan; Bruijn, de Douwe; Olthuis, Wouter; Berg, van den Albert

    2015-01-01

    For the first time, chloride ions are measured wirelessly in concrete. The half-cell potential of a silver/silver chloride (Ag/AgCl) electrode, which corresponds to the concentration of chloride ions, is measured wirelessly. The sensor system (the Ag/AgCl and a reference electrode) is embedded in co

  3. Resistant mechanism study of benzalkonium chloride selected Salmonella Typhimurium mutants.

    Science.gov (United States)

    Guo, Wei; Cui, Shenghui; Xu, Xiao; Wang, Haoyan

    2014-02-01

    Benzalkonium chloride is one of the invaluable biocides that is extensively used in healthcare settings as well as in the food processing industry. After exposing wild-type Salmonella Typhimurium 14028s or its AcrAB inactivation mutant to gradually increasing levels of benzalkonium chloride, resistance mutants S-41, S-150, S-AB-23, S-AB-38, and S-AB-73 were selected and these mutants also showed a 2-64-fold stable minimum inhibitory concentration (MIC) increase to chloramphenicol, ciprofloxacin, nalidixic acid, and tetracycline. In S-41 and S-150, the expression of acrB was increased 2.7- and 7.6-fold, and ΔtolC or ΔacrAB mutants of S-41 and S-150 showed the same MICs to all tested antimicrobials as the equivalent Salmonella Typhimurium 14028s mutants. However, in S-AB-23, S-AB-38, and S-AB-73, the expression of acrF was increased 96-, 230-, and 267-fold, respectively, and ΔtolC or ΔacrEF mutants of S-AB-23, S-AB-38, and S-AB-73 showed the similar MICs to all tested antimicrobials as the ΔtolC mutant of Salmonella Typhimurium 14028s. Our data showed that constitutively over-expressed AcrAB working through TolC was the main resistance mechanism in ST14028s benzalkonium chloride resistance mutants. However, after AcrAB had been inactivated, benzalkonium chloride-resistant mutants could still be selected and constitutively over-expressed, AcrEF became the dominant efflux pump working through TolC and being responsible for the increasing antimicrobial resistance. These data indicated that different mechanisms existed for acrB and acrF constitutive over-expression. Since exposure to benzalkonium chloride may lead to Salmonella mutants with a decreased susceptibility to quinolones, which is currently one of the drugs of choice for the treatment of life-threatening salmonelosis, research into the pathogenesis and epidemiology of the benzalkonium chloride resistance mutants will be of increasing importance.

  4. [Evaluating risk of health disorders in workers engaged into polyvinyl chloride, vinyl chloride and caustic soda production (according to data collected by polls)].

    Science.gov (United States)

    D'iakovich, O A

    2014-01-01

    The authors represent data of automated system for quantitative risk evaluation of main pathologic syndromes in workers engaged into polyvinyl chloride, vinyl chloride and caustic soda production. Vinyl chloride and mercury levels at the investigation time corresponded with MAC. Relationship was seen between value of arterial hypertension risk and duration of contact with both vinyl chloride and mercury. Risk values for functional disorders of liver, endocrine system and nervous system were in weak correlation with length of exposure to mercury at work. Workers exposed to mercury appeared to have lower self-estimation of health state and higher dissatisfaction with the work.

  5. Enthalpy and entropy interaction parameters of sodium chloride with some monosaccharides in water

    Institute of Scientific and Technical Information of China (English)

    ZHUO; Kelei; WANG; Jianji; BAI; Guangyue; YAN; Haike; WANG

    2004-01-01

    Dilution enthalpies of sodium chloride and some monosaccharides (glucose, galactose, xylose, arabinose, and fructose) in water and mixing enthalpies of aqueous sodium chloride and these monosaccharide solutions were measured by using an improved precision semimicro-titration calorimeter. Transfer enthalpies of sodium chloride from water to aqueous saccharide solutions were evaluated as well as enthalpy interaction parameters of sodium chloride with these monosaccharides in water. Combined with Gibbs energy interaction parameters, entropy interaction parameters were also obtained. The results show that interactions of the saccharides with sodium chloride depend on the stereochemistry of saccharide molecules. These interaction parameters can identify stereochemical structure of saccharide molecules.

  6. An insight into the passivation of cupronickel alloys in chloride environment

    Indian Academy of Sciences (India)

    J Mathiyarasu; N Palaniswamy; V S Muralidharan

    2001-02-01

    Cupronickels offer enhanced corrosion protection in marine environments by the formation of passive films on the surface. Cyclic voltammetric studies were carried on cupronickels in chloride solutions at H 6.3 to understand the role of chloride ions in passive film formation. Increase in nickel content of the alloy and of chloride ions in solution decreases film resistance. Chloride ions take part in reduction of the passive film to copper. A solid-state model for passive film formation involving chloride ions has been attempted.

  7. Properties of a conductive cellular chloride pathway in the skin of the toad (Bufo bufo)

    DEFF Research Database (Denmark)

    Larsen, Erik Hviid; Kristensen, P

    1978-01-01

    of the steady-state conductance and the steady-state chloride current reveal that the chloride pathway has maximum conductance for V approximately -80 mV (outside of the skin being negative) and approaches a non-conducting safe for V greater than 0 mV. This strong outward going rectification is a steady......-compartment model indicate that the strong steady-state chloride current rectification cannot be obtained if only the intracellular chloride concentration and the membrane potentials are allowed to vary ("Goldman-rectification"). It is suggested, therefore, that the premeability of the chloride pathway varies...

  8. Mathematical Model of a Lithium/Thionyl Chloride Battery

    Energy Technology Data Exchange (ETDEWEB)

    Jain, M.; Jungst, R.G.; Nagasubramanian, G.; Weidner, J.W.

    1998-11-24

    A mathematical model of a spirally wound lithium/thionyl chloride primary battery has been developed ~d used for parameter estimation and design studies. The model formulation is based on the fimdarnental Consemation laws using porous electrode theory and concentrated solution theory. The model is used to estimate the difision coefficient and the kinetic parameters for the reactions at the anode and the cathode as a function of temperature. These parameters are obtained by fitting the simulated capacity and average cell voltage to experimental data over a wide range of temperatures (-55 to 49"C) and discharge loads (10 to 250 ohms). The experiments were performed on D-sized, cathode-limited, spirally wound lithium/thionyl chloride cells. The model is also used to study the effkct of cathode thickness on the cell capacity as a finction of temperature, and it was found that the optimum thickness for the cathode- limited design is temperature and load dependent.

  9. Physical and conductivity properties of poly (vinyl chloride) ionomers

    Science.gov (United States)

    Misra, Nira; Panda, H. S.; Kapusetti, Govinda; Jaiswal, Shilpa; Bhattacharya, Subhratanu

    2011-02-01

    Poly (vinyl chloride)(PVC) is a cheapest plastic. Importance of PVC based ionomer has been gradually being popularizing due to compatibility of PVC with a number of salts to replace polyethylene oxide based ionomer. Under present investigation few of chloride group of PVC chain have been replaced by basic thiouronium group and these thiouronium groups are further oxidized to sulfonate group. Introduction of thiouronium group in PVC is confirmed through FTIR and further its oxidation to sulfonate group is also confirmed by FTIR. Conductivity in different stoichiometric ratio of PVCTU and PVCSO3H was studied and found that PVCTU: PVCSO3H in 1:1 ratio has conductivity near to pure PVC (10-9 Ohm-1 cm-1) and increases with proportion of PVCSO3Na in the mixture (10-6 Ohm-1 cm-1) for pure PVC, PVCTU has less conductivity not much significant.

  10. Chlorine Nuclear Quadrupole Hyperfine Structure in the Vinyl - Chloride Complex

    Science.gov (United States)

    Leung, Helen O.; Marshall, Mark D.; Messinger, Joseph P.

    2015-06-01

    The microwave spectrum of the vinyl chloride--hydrogen chloride complex, presented at last year's symposium, is greatly complicated by the presence of two chlorine nuclei as well as an observed, but not fully explained tunneling motion. Indeed, although it was possible at that time to demonstrate conclusively that the complex is nonplanar, the chlorine nuclear quadrupole hyperfine splitting in the rotational spectrum resisted analysis. With higher resolution, Balle-Flygare Fourier transform microwave spectra, the hyperfine structure has been more fully resolved, but appears to be perturbed for some rotational transitions. It appears that knowledge of the quadrupole coupling constants will provide essential information regarding the structure of the complex, specifically the location of the hydrogen atom in HCl. Our progress towards obtaining values for these constants will be presented.

  11. Plastics and carcinogenesis: The example of vinyl chloride

    Directory of Open Access Journals (Sweden)

    Paul Wesley Brandt-Rauf

    2012-01-01

    Full Text Available The manufacture, use and disposal of various plastics can pose numerous health risks, including the risk of cancer. A model example of carcinogenic risk from plastics is provided by polyvinyl chloride, since it is composed of the known human carcinogen vinyl chloride (VC. In recent years, much has been learned about the molecular biological pathways of VC carcinogenesis. This has led to molecular epidemiologic studies of VC carcinogenesis in exposed human populations which have identified useful biomarkers of exposure, effect and susceptibility for VC. These studies have in turn provided the basis for new molecular approaches for the prevention and treatment of VC cancers. This model could have much wider applicability for many other carcinogenic exposures and many other human cancers.

  12. Uranium (III) precipitation in molten chloride by wet argon sparging

    Science.gov (United States)

    Vigier, Jean-François; Laplace, Annabelle; Renard, Catherine; Miguirditchian, Manuel; Abraham, Francis

    2016-06-01

    In the context of pyrochemical processes for nuclear fuel treatment, the precipitation of uranium (III) in molten salt LiCl-CaCl2 (30-70 mol%) at 705 °C is studied. First, this molten chloride is characterized with the determination of the water dissociation constant. With a value of 10-4.0, the salt has oxoacid properties. Then, the uranium (III) precipitation using wet argon sparging is studied. The salt is prepared using UCl3 precursor. At the end of the precipitation, the salt is totally free of solubilized uranium. The main part is converted into UO2 powder but some uranium is lost during the process due to the volatility of uranium chloride. The main impurity of the resulting powder is calcium. The consequences of oxidative and reductive conditions on precipitation are studied. Finally, coprecipitation of uranium (III) and neodymium (III) is studied, showing a higher sensitivity of uranium (III) than neodymium (III) to precipitation.

  13. Solvolyses of Benzoyl Chlorides in Weakly Nucleophilic Media

    Directory of Open Access Journals (Sweden)

    Haldon Carl Harris

    2011-07-01

    Full Text Available Rate constants and activations parameters are reported for solvolyses of p-Z-substituted benzoyl chlorides (1, Z = OMe, Me, H, and Cl in 97% w/w hexafluoroisopropanol-water (97H. Additional kinetic data are reported for solvolyses in acetic and formic acids. Plots of log k vs. σp in 97H are consistent with previous research showing that a cationic reaction channel is dominant, even for solvolyses of 1, Z = NO2. A benzoyl cation intermediate was trapped by Friedel-Crafts reaction with 1,3,5-trimethoxybenzene in hexafluoroisopropanol. The results are explained by an SN2-SN1 spectrum of mechanisms with variations in nucleophilic solvent assistance. Ab initio calculations of heterolytic bond dissociation energies of various chloro- and fluoro-substituted and other benzoyl chlorides are correlated with log k for solvolyses.

  14. INTERACTION OF POLYVINYLPYRROLIDONE WITH METAL CHLORIDE AQUEOUS SOLUTIONS

    Institute of Scientific and Technical Information of China (English)

    Mohammad Saleem Khan; Khaista Gul; Najeeb Ur Rehman

    2004-01-01

    Interactions of polyvinylpyrrolidone (PVP) with metal chlorides (MgCl2, CaCl2, KC1 and BaC12) have been investigated by viscometric and spectrophotometric techniques in aqueous solutions. Intrinsic viscosity [η] of (PVP) has shown a discontinuity with varying concentration of metal chlorides. The decreasing order of effectiveness of cation is K1+>Ca2+> Mg2+> Ba2+ for poly(vinylpyrrolidone) solution. Changes in the absorption spectra of the cosolutes were observed in the presence of PVP in the lower limit of the UV-visible region i.e. 200-210 nm. These changes were attributed to interaction of PVP molecules with the cosolute molecules. As the concentration of the cosolute increased, a red shift in the peaks was observed, indicating an increase in interaction between PVP and cosolutes.

  15. Molybdenum chloride catalysts for Z-selective olefin metathesis reactions

    Science.gov (United States)

    Koh, Ming Joo; Nguyen, Thach T.; Lam, Jonathan K.; Torker, Sebastian; Hyvl, Jakub; Schrock, Richard R.; Hoveyda, Amir H.

    2017-01-01

    The development of catalyst-controlled stereoselective olefin metathesis processes has been a pivotal recent advance in chemistry. The incorporation of appropriate ligands within complexes based on molybdenum, tungsten and ruthenium has led to reactivity and selectivity levels that were previously inaccessible. Here we show that molybdenum monoaryloxide chloride complexes furnish higher-energy (Z) isomers of trifluoromethyl-substituted alkenes through cross-metathesis reactions with the commercially available, inexpensive and typically inert Z-1,1,1,4,4,4-hexafluoro-2-butene. Furthermore, otherwise inefficient and non-stereoselective transformations with Z-1,2-dichloroethene and 1,2-dibromoethene can be effected with substantially improved efficiency and Z selectivity. The use of such molybdenum monoaryloxide chloride complexes enables the synthesis of representative biologically active molecules and trifluoromethyl analogues of medicinally relevant compounds. The origins of the activity and selectivity levels observed, which contradict previously proposed principles, are elucidated with the aid of density functional theory calculations.

  16. Electrowinning of lead powder from chloride leach liquor

    Energy Technology Data Exchange (ETDEWEB)

    Owais, Ashour [Suez Canal Univ., Suez (Egypt). Metallurgical and Materials Engineering Dept.

    2012-11-15

    Electrowinning of lead powder from chloride leach liquor obtained from secondary lead slag leached in hydrochloric acid is the main aim of this work. The resulted lead chloride solution (leachate) containing 2.2 wt.-% Pb and 1.24 wt.-% HCl was electrowon in an electrolytic cell containing one graphite plate as inert anode and two lead sheets as starting permanent cathodes. Different electrolysis parameters such as current density, electrolyte temperature and electrolyte stirring rate were studied. As indicated by SEM, EDX and XRD analyses, fine and pure (100 % Pb) powders with a dispersed and needle-like shape were formed with cathodic current efficiency up to 67.9 % and electrical energy demand ranges from 0.809 to 4.998 kWh/kg Pb with productivity up to 2.63 g/Ah. (orig.)

  17. Electrochemical synthesis and characterization of chloride doped polyaniline

    Indian Academy of Sciences (India)

    A M Pharhad Hussain; A Kumar

    2003-04-01

    Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl– ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.

  18. Viscosity and density of some lower alkyl chlorides and bromides

    Energy Technology Data Exchange (ETDEWEB)

    Rutherford, W.M.

    1988-07-01

    A high-pressure capillary viscometer, used previously to measure the viscosity of methyl chloride was rebuilt to eliminate the first-order dependence of the measured viscosity on the value assumed for the density of the fluid being investigated. At the same time, the system was arranged so that part of the apparatus could be used to measure density by a volumetric displacement technique. Viscosity and density were measured for ethyl chloride, 1-chloropropane, 1-chlorobutane, methyl bromide, ethyl bromide, and 1-bromopropane. The temperature and pressure ranges of the experiments were 20-150 /sup 0/C and 0.27-6.99 MPa, respectively. The accuracy of the viscosity measurements was estimated to be +-1% and of the density measurements, +-0.2%.

  19. Probabilistic Models and Computational Methods for Chloride Ingress in Concrete

    DEFF Research Database (Denmark)

    Engelund, S.

    Within the last decades it has been recognized that reinforced concrete structures are subject to a number of destructive mechanisms which might affect the structure in such a way that it is not able to fulfil its purpose efficiently. The present report focuses on chloride ingress and chloride......-initiated corrosion of the reinforcement, because experience has shown that in Denmark this is one of the most common destructive mechanisms. In order to ensure that a given reinforced concrete structure is able to fulfil its purpose extensive measurements are performed and on the basis of these measurements...... are costly, and careful planning is mandatory. The planning can be performed on the basis of classical decision theory (see e.g. Raiffa and Schlaifer). However, in order to use decision theory, it is necessary to formulate a probabilistic model of the considered problem....

  20. High rate lithium/thionyl chloride bipolar battery development

    Energy Technology Data Exchange (ETDEWEB)

    Russell, P.G. [Yardney Technical Products, Inc., Pawcatuck, CT (United States); Goebel, F. [Yardney Technical Products, Inc., Pawcatuck, CT (United States)

    1995-04-01

    The lithium/thionyl chloride (Li/SOCl{sub 2}) electrochemistry is capable of providing high power and high specific power, especially under pulse discharge conditions, when cells containing thin components are arranged in a bipolar configuration. This paper describes recent work concerned with bipolar cell design, cathode evaluation, component manufacturing methods, and the assembly and testing of bipolar modules containing up to 150 cells for Sonobuoy application. (orig.)

  1. High rate lithium-thionyl chloride bipolar battery development

    Energy Technology Data Exchange (ETDEWEB)

    Russell, P.G.; Goebel, F. [Yardney Technical Products, Inc., Pawcatuck, CT (United States)

    1994-12-31

    The lithium/thionyl chloride system is capable of providing both high power and high energy density when cells containing thin components are arranged in a bipolar configuration. Electrode current densities in excess of 300mA/cm{sup 2} are achieved during pulse discharge. The present work is concerned with bipolar cell design, cathode evaluation, component manufacturing methods, and the assembly and testing of bipolar modules containing up to 150 cells.

  2. High rate lithium/thionyl chloride bipolar battery development

    Science.gov (United States)

    Russell, P. G.; Goebel, F.

    The lithium/thionyl chloride ( {Li}/{SOCl2}) electrochemistry is capable of providing high power and high specific power, especially under pulse discharge conditions, when cells containing thin components are arranged in a bipolar configuration. This paper describes recent work concerned with bipolar cell design, cathode evaluation, component manufacturing methods, and the assembly and testing of bipolar modules containing up to 150 cells for Sonobuoy application.

  3. Mechanism of resistance to benzalkonium chloride by Pseudomonas aeruginosa.

    OpenAIRE

    Sakagami, Y; Yokoyama, H; Nishimura, H.; Ose, Y; Tashima, T.

    1989-01-01

    The mechanisms of resistance of Pseudomonas aeruginosa to benzalkonium chloride (BC) were studied. The effluence of cell components was observed in susceptible P. aeruginosa by electron microscopy, but resistant P. aeruginosa seemed to be undamaged. No marked changes in cell surface potential between Escherichia coli NIHJC-2 and a spheroplast strain were found. The contents of phospholipids (PL) and fatty and neutral lipids (FNL) in the cell walls of resistant P. aeruginosa were higher than t...

  4. Fatal Cesium Chloride Toxicity After Alternative Cancer Treatment

    OpenAIRE

    Sessions, Daniel; Heard, Kennon; Kosnett, Michael

    2013-01-01

    Background: Cesium chloride (CsCl) is sold as a treatment for several types of cancers. The purported mechanism of action is alkalinization of relatively acidic neoplastic cells. The efficacy of CsCl has not been demonstrated in controlled experiments. Oral and intravenous CsCl use has been associated with seizures, cardiotoxicity, syncope, and death. Although intratumoral treatment with various antineoplastic agents is described, no cases of intratumoral cancer treatment with CsCl have been ...

  5. Tertiary amines nucleophilicity in quaternization reaction with benzyl chloride

    Directory of Open Access Journals (Sweden)

    Ksenia S. Yutilova

    2016-03-01

    Full Text Available Quaternization reaction of tertiary amines with benzyl chloride was investigated. Reaction orders with respect to the reactants were determined. Kinetic scheme of quaternization reaction was found to be corresponding to reversible process. An influence of amines basicity and steric factor of alkyl substituent bound to the nitrogen atom on tertiary amines reactivity as nucleophiles was studied. It was shown that the rate constants of direct reaction step may serve as a measure of nucleophilicity of amines.

  6. The Use of Electrodiffusion for Removing Chlorides from Concrete

    OpenAIRE

    2016-01-01

    The article presents a description of ion migration in a concrete pore liquid caused by an external electric field. The equation of the flow of aggressive chloride ions is formulated on the basis of partial equations of mass balance. It is assumed that electrochemical potential is in classical form, then an attempt is made to determine the average diffusion coefficient using the inverse diffusion Eq.(3.9).

  7. Dynamic viscoelastic properties of polyvinyl chloride with physical aging

    Science.gov (United States)

    Tian, Fang; Luo, Yingshe; Yin, Shuiping; Wang, Hong; Cao, Chun

    2015-11-01

    The experimental research of dynamic viscoelastic properties of polyvinyl chloride was conducted by the dynamic mechanical analysis method in this paper. And the fitting equation of dynamic modulus of polymers has been presented. Based on the time-aging time equivalent principle, horizontal shift factor and vertical shift factor of aging time are carried out, which proposes a novel method for the research on time-aging time equivalent analysis of dynamic mechanical properties of polymers during physical aging.

  8. Chemical Attribution Signatures of Cyanogen Chloride from Commercial Sources

    Science.gov (United States)

    2016-10-01

    HP GAS, LLC .........................................15  C: LISTING OF IMPURITIES DETECTED IN CYANOGEN CHLORIDE CYLINDERS FROM SEMICONDUCTOR ...most recent spectra in the front. Spectra were normalized to the H2O resonance at 2.17 ppm: (top) HP Gas, (middle) Semiconductor Resources, and...LLC (Baytown, TX), including Stillwater Consultants (Stillwater, MN), LMTG (Roanoke, LA), and TL2 Gases (Sulphur, LA); 28 from   4 Semiconductor

  9. The Use of Electrodiffusion for Removing Chlorides from Concrete

    Science.gov (United States)

    Alsabry, A.

    2016-12-01

    The article presents a description of ion migration in a concrete pore liquid caused by an external electric field. The equation of the flow of aggressive chloride ions is formulated on the basis of partial equations of mass balance. It is assumed that electrochemical potential is in classical form, then an attempt is made to determine the average diffusion coefficient using the inverse diffusion Eq.(3.9).

  10. Comment on "Local impermeant anions establish the neuronal chloride concentration".

    Science.gov (United States)

    Luhmann, Heiko J; Kirischuk, Sergei; Kilb, Werner

    2014-09-01

    Glykys et al. (Reports, 7 February 2014, p. 670) proposed that cytoplasmic impermeant anions and polyanionic extracellular matrix glycoproteins establish the local neuronal intracellular chloride concentration, [Cl(-)]i, and thereby the polarity of γ-aminobutyric acid type A (GABAA) receptor signaling. The experimental procedures and results in this study are insufficient to support these conclusions. Contradictory results previously published by these authors and other laboratories are not referred to.

  11. Methyl chloride production from methane over lanthanum-based catalysts.

    Science.gov (United States)

    Podkolzin, Simon G; Stangland, Eric E; Jones, Mark E; Peringer, Elvira; Lercher, Johannes A

    2007-03-07

    The mechanism of selective production of methyl chloride by a reaction of methane, hydrogen chloride, and oxygen over lanthanum-based catalysts was studied. The results suggest that methane activation proceeds through oxidation-reduction reactions on the surface of catalysts with an irreducible metal-lanthanum, which is significantly different from known mechanisms for oxidative chlorination. Activity and spectroscopic measurements show that lanthanum oxychloride (LaOCl), lanthanum trichloride (LaCl3), and lanthanum phases with an intermediate extent of chlorination are all active for this reaction. The catalyst is stable with no noticeable deactivation after three weeks of testing. Kinetic measurements suggest that methane activation proceeds on the surface of the catalyst. Flow and pulse experiments indicate that the presence of hydrogen chloride is not required for activity, and its role appears to be limited to maintaining the extent of catalyst chlorination. In contrast, the presence of gas-phase oxygen is essential for catalytic activity. Density-functional theory calculations suggest that oxygen can activate surface chlorine species by adsorbing dissociatively and forming OCl surface species, which can serve as an active site for methane activation. The proposed mechanism, thus, involves changing of the formal oxidation state of surface chlorine from -1 to +1 without any changes in the oxidation state of the underlying metal.

  12. Modeling chloride penetration into concrete with light-weight aggregates

    Energy Technology Data Exchange (ETDEWEB)

    Maage, M.; Helland, S.; Carlsen, J. E. [SELMER ASA, Oslo (Norway)

    2000-07-01

    Results of a program of studies designed to provide input to a model for estimating the initiation period of reinforcement corrosion and to document chloride ingress into various practical concretes made with light-weight aggregates, depending on a number of variables in curing and exposure conditions, as well as concrete composition and materials, are discussed. Variables included curing time before exposure; curing temperature; exposure temperature and time; type of exposure; and type of binder. Results achieved correlate well with the initial hypothesis i.e. that the achieved chloride coefficient decreases with increasing exposure time and also with increasing curing time.Surface chloride content as the environmental load, was shown to increase with exposure time during the first years, and decrease with increased curing time and exposure temperature. The achieved diffusion coefficient was found to be independent of curing and exposure temperature, but decreased with longer exposure time and the addition of slag. Increasing the salt concentration in the exposure water and the introduction of slag increased the time dependency of the achieved diffusion coefficient. 11 refs., 2 tabs., 7 figs.

  13. Prediction of Chloride Diffusion in Concrete Structure Using Meshless Methods

    Directory of Open Access Journals (Sweden)

    Ling Yao

    2016-01-01

    Full Text Available Degradation of RC structures due to chloride penetration followed by reinforcement corrosion is a serious problem in civil engineering. The numerical simulation methods at present mainly involve finite element methods (FEM, which are based on mesh generation. In this study, element-free Galerkin (EFG and meshless weighted least squares (MWLS methods are used to solve the problem of simulation of chloride diffusion in concrete. The range of a scaling parameter is presented using numerical examples based on meshless methods. One- and two-dimensional numerical examples validated the effectiveness and accuracy of the two meshless methods by comparing results obtained by MWLS with results computed by EFG and FEM and results calculated by an analytical method. A good agreement is obtained among MWLS and EFG numerical simulations and the experimental data obtained from an existing marine concrete structure. These results indicate that MWLS and EFG are reliable meshless methods that can be used for the prediction of chloride ingress in concrete structures.

  14. Multi-scale modelling of uranyl chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Thanh-Nghi; Duvail, Magali, E-mail: magali.duvail@icsm.fr; Villard, Arnaud; Dufrêche, Jean-François, E-mail: jean-francois.dufreche@univ-montp2.fr [Institut de Chimie Séparative de Marcoule (ICSM), UMR 5257, CEA-CNRS-Université Montpellier 2-ENSCM, Site de Marcoule, Bâtiment 426, BP 17171, F-30207 Bagnols-sur-Cèze Cedex (France); Molina, John Jairo [Fukui Institute for Fundamental Chemistry, Kyoto University, Takano-Nishihiraki-cho 34-4, Sakyo-ku, Kyoto 606-8103 (Japan); Guilbaud, Philippe [CEA/DEN/DRCP/SMCS/LILA, Marcoule, F-30207 Bagnols-sur-Cèze Cedex (France)

    2015-01-14

    Classical molecular dynamics simulations with explicit polarization have been successfully used to determine the structural and thermodynamic properties of binary aqueous solutions of uranyl chloride (UO{sub 2}Cl{sub 2}). Concentrated aqueous solutions of uranyl chloride have been studied to determine the hydration properties and the ion-ion interactions. The bond distances and the coordination number of the hydrated uranyl are in good agreement with available experimental data. Two stable positions of chloride in the second hydration shell of uranyl have been identified. The UO{sub 2}{sup 2+}-Cl{sup −} association constants have also been calculated using a multi-scale approach. First, the ion-ion potential averaged over the solvent configurations at infinite dilution (McMillan-Mayer potential) was calculated to establish the dissociation/association processes of UO{sub 2}{sup 2+}-Cl{sup −} ion pairs in aqueous solution. Then, the association constant was calculated from this potential. The value we obtained for the association constant is in good agreement with the experimental result (K{sub UO{sub 2Cl{sup +}}} = 1.48 l mol{sup −1}), but the resulting activity coefficient appears to be too low at molar concentration.

  15. Investigation of lithium-thionyl chloride battery safety hazards

    Science.gov (United States)

    Attia, A. I.; Gabriel, K. A.; Burns, R. P.

    1983-01-01

    In the ten years since the feasibility of a lithium-thionyl chloride cell was first recognized (1) remarkable progress has been made in hardware development. Cells as large as 16,000 Ah (2) and batteries of 10.8 MWh (3) have been demonstrated. In a low rate configuration, energy densities of 500 to 600 Wh/kg are easily achieved. Even in the absence of reported explosions, safety would be a concern for such a dense energetic package; the energy density of a lithium-thionyl chloride cell is approaching that of dynamite (924 Wh/kg). In fact explosions have occurred. In general the hazards associated with lithium-thionyl chloride batteries may be divided into four categories: Explosions as a result of an error in battery design. Very large cells were in prototype development prior to a full appreciation of the hazards of the system. It is possible that some of the remaining safety issues are related to cell design; Explosions as a result of external physical abuse such as cell incineration and puncture; Explosions due to short circuiting which could lead to thermal runaway reactions. These problems appear to have been solved by changes in the battery design (4); and Explosions due to abnormal electrical operation (i.e., charging (5) and overdischarging (6) and in partially or fully discharged cells on storage (7 and 8).

  16. Permeation of protective clothing materials by methylene chloride and perchloroethylene.

    Science.gov (United States)

    Vahdat, N

    1987-07-01

    The permeation of methylene chloride and perchloroethylene through seven protective clothing materials was studied to determine the permeation parameters, and to investigate the effect of solubility (polymer weight gain) and material thickness on the permeation parameters. The materials tested were two different nitrile rubbers, neoprene, Combination (a blend of natural rubber, neoprene and nitrile), two different polyvinyl chlorides, and polyvinyl alcohol. Methylene chloride permeated through all materials, except PVA, with breakthrough times in the range of 2 to 8 min, and permeation rates in the range of 1250-5800 micrograms/cm2 X min. PVA and unsupported nitrile offered good protection against perchloroethylene with breakthrough time occurring after 2 hr. Perchloroethylene permeated through the other materials with breakthrough times in the range of 8 to 36 min and permeation rates in the range of 200 to 1600 micrograms/cm2 X min. It was shown that for both chemicals, there is a correlation between the solubility (weight gain) and the ratio of permeation rate to breakthrough time (PR/BT). For all material/chemical pairs, an increase in solubility, increased (PR/BT). The change in material thickness had an effect on breakthrough time and permeation rate, but no effect on normalized breakthrough time. An increase in thickness reduced permeation rate and increased breakthrough time.

  17. Control of Perovskite Crystal Growth by Methylammonium Lead Chloride Templating.

    Science.gov (United States)

    Binek, Andreas; Grill, Irene; Huber, Niklas; Peters, Kristina; Hufnagel, Alexander G; Handloser, Matthias; Docampo, Pablo; Hartschuh, Achim; Bein, Thomas

    2016-04-20

    State-of-the-art solar cells based on methylammonium lead iodide (MAPbI3 ) now reach efficiencies over 20 %. This fast improvement was possible with intensive research in perovskite processing. In particular, chloride-based precursors are known to have a positive influence on the crystallization of the perovskite. Here, we used a combination of in-situ X-ray diffraction and charge-transport measurements to understand the influence of chloride during perovskite crystallization in planar heterojunction solar cells. We show that MAPbCl3 crystallizes directly after the deposition of the starting solution and acts as a template for the formation of MAPbI3 . Additionally, we show that the charge-carrier mobility doubles by extending the time for the template formation. Our results give a deeper understanding of the influence of chloride in the synthesis of MAPbI3 and illustrate the importance of carefully controlling crystallization for reproducible, high-efficiency solar cells.

  18. The effects of surface treatments on rapid chloride permeability tests

    KAUST Repository

    Yoon, Seyoon

    2012-08-01

    Surface treatments are commonly applied to improve the chloride resistance of concrete structures exposed to saline environments. Information on chloride ingress to surface-treated concrete is mostly provided by application of the rapid chloride permeability test (RCPT); this test is short in duration and provides rapid results. This study presents a numerical formulation, based on the extended Nernst-Plank/Poisson (NPP) equation, to model the effect of the surface treatment on a sample tested by RCPT. Predictions of the model are compared to experimental measurements. The simulations show that the results from RCPT, in terms of ionic profiles and measurement of the electric field, are dependent on the effectiveness of surface treatments. During RCPT, highly effective surface treatments cause both cations and anions to flocculate at the interface between the surface treatment and the concrete, creating a local electric field. Our numerical model includes these phenomena and presents a methodology to obtain more accurate diffusivities of the surface-treated- concrete from RCPT. © 2012 Elsevier B.V. All rights reserved.

  19. PCDD/F catalysis by metal chlorides and oxides.

    Science.gov (United States)

    Zhang, Mengmei; Yang, Jie; Buekens, Alfons; Olie, Kees; Li, Xiaodong

    2016-09-01

    Model fly ash (MFA) samples were composed of silica, sodium chloride, and activated carbon, and doped with metal (0.1 wt% Cu, Cr, Ni, Zn and Cd) chloride or oxide. Each sample was de novo tested at 350 °C for 1 h, in a flow of gas (N2, N2 + 10% O2, +21% O2 or +10% H2) to investigate the effect of metal catalyst and gas composition on PCDD/F formation. Total PCDD/F yield rises rapidly with oxygen content, while the addition of hydrogen inhibits the formation and chlorination of PCDD/F. The amount of PCDD on average rises linearly with the oxygen concentration, while that of PCDF follows a reaction order of about 1/2; thus the PCDF to PCDD ratio drops when more oxygen becomes available. Some samples do not follow this trend. Chlorides are much more active than oxides, yet there are marked differences between individual metals. Principal component analysis (PCA) was applied to study the signatures from all samples, showing their unique specificity and diversity. Each catalyst shows a different signature within its individual homologue groups, demonstrating that these signatures are not thermodynamically controlled. Average congener patterns do not vary considerably with oxygen content changing from oxidising (air) to reducing (nitrogen, hydrogen).

  20. Preparation and characterization of poly-(methacrylatoethyl trimethylammonium chloride-co-vinylbenzyl chloride-co-ethylene dimethacrylate monolith

    Directory of Open Access Journals (Sweden)

    Eko Malis

    2015-05-01

    Full Text Available A polymer monolithic column, poly-(methacrylatoethyltrimethylammonium chloride-co-vinylbenzyl chloride-co-ethylene dimethacrylate or poly-(MATE-co-VBC-co-EDMA was successfully prepared in the current study by one-step thermally initiated in situ polymerization, confined in a steel tubing of 0.5 mm i.d. and 1/16” o.d. The monoliths were prepared from methacrylatoethyltrimethylammonium chloride (MATE and vinylbenzyl chloride (VBC as monomer and ethylene dimethacrylate (EDMA as crosslinker using a binary porogen system of 1-propanol and 1,4-butanediol. The inner wall of steel tubing was pretreated with 3-methacryloxypropyl-trimethoxysilane (MAPS. In order to obtain monolith with adequate column efficiency and low flow resistance, some parameters such as total monomer concentration (%T and crosslinker concentration (%C were optimized. The morphology of this monolith was assessed by scanning electron microscopy (SEM. The properties of the monolithic column, such as permeability, binding capacity, and pore size distribution were also characterized in detail. From the results of the characterization of all monolith variation, monolith with %T 30 %C 50 and %T 35 %C 50 give the best characteristic. These monoliths have high permeability, adequate molecular recognition sites (represented with binding capacity value of over 20 mg/mL, and have over 80% flow through pores in their pore structure contribute to low flow resistance. The resulted monolithic columns have promising potential for dual mode liquid chromatography. MATE may contribute for anion-exchange while VBC may responsible for reversed-phase liquid chromatography.

  1. Continuous microcellular foaming of polyvinyl chloride and compatibilization of polyvinyl chloride and polylactide composites

    Science.gov (United States)

    Shah, Bhavesh

    This dissertation focuses on overcoming existing limitations of WPCs which prevent them from realizing their full market potential. These limitations include: (i) lack of a continuous extrusion process for microcellular foaming of polyvinyl chloride (PVC) and its composites using supercritical fluids to reduce the high density of the WPCs, (ii) need for an efficient coupling agent for WPCs to overcome the poor compatibility between wood and plastic, and (iii) unproven use of wood as a filler for the biopolymer polylactide (PLA) to make "green" composites. These limitations were addressed through experimentation to develop a continuous extrusion process for microcellular foaming, and through surface modification of wood flour using natural coupling agents. The effects of wood flour, acrylic modifier and plasticizer content on the rheological properties of PVC based WPCs were studied using an extrusion capillary rheometer and a two-level factorial design. Wood flour content and acrylic modifier content were the major factors affecting the die swell ratio. Addition of plasticizer decreased the true viscosity of unfilled and filled PVC, irrespective of the acrylic modifier content. However, the addition of acrylic modifier significantly increased the viscosity of unfilled PVC but decreased the composite viscosity. Results of the rheological study were used to set baseline conditions for the continuous extrusion foaming of PVC WPCs using supercritical CO 2. Effects of material composition and processing conditions on the morphology of foamed samples were investigated. Foamed samples were produced using various material compositions and processing conditions, but steady-state conditions could not be obtained for PVC. Thus the relationships could not be determined. Incompatibility between wood flour and PVC was the focus of another study. The natural polymers chitin and chitosan were used as novel coupling agents to improve interfacial adhesion between the polymer matrix

  2. On the existence of ``l-threonine formate'', ``l-alanine lithium chloride'' and ``bis l-alanine lithium chloride'' crystals

    Science.gov (United States)

    Petrosyan, A. M.; Ghazaryan, V. V.; Fleck, M.

    2013-03-01

    We argue that the recently reported crystals "L-threonine formate" as well as "L-alanine lithium chloride" and "bis L-alanine lithium chloride" actually are the well-known crystals L-threonine and L-alanine, respectively.

  3. THE ROLE OF CHLORIDE ANION AND CFTR IN KILLING OF PSEUDOMONAS AERUGINOSA BY NORMAL AND CF NEUTROPHILS

    OpenAIRE

    Richard G. Painter; Bonvillain, Ryan W.; Vincent G Valentine; Lombard, Gisele A.; LaPlace, Stephanie G.; Nauseef, William M.; Wang, Guoshun

    2008-01-01

    Chloride anion is essential for myeloperoxidase to produce hypochlorous acid (HOCl) in neutrophils (PMNs). To define whether chloride availability to PMNs affects their HOCl production and microbicidal capacity, we examined how extracellular chloride concentration affects killing of Pseudomonas aeruginosa (PsA) by normal neutrophils. PMN-mediated bacterial killing was strongly dependent on extracellular chloride concentration. Neutrophils in a chloride-deficient medium killed PsA poorly. Howe...

  4. Chemistry and Spectroscopy of Frozen Chloride Salts on Icy Bodies

    Science.gov (United States)

    Johnson, Paul; Thomas, Elena C.; Hodyss, Robert; Vu, Tuan; Choukroun, Mathieu

    2016-10-01

    Currently, our understanding of the chemical composition of Europa's surface is our best means of inferring constraints on the subsurface ocean composition and its subsequent habitability. The bulk of our knowledge of Europa surface chemistry can be traced to near infrared spectra recorded by the Near Infrared Mapping Spectrometer on the Galileo spacecraft. However, the usefulness of this and other remote sensing data is limited by the availability of spectral libraries of candidate materials under relevant conditions (temperature, thermal/radiation history, etc.). Chloride salts are expected to exist on the surface of Europa, and other icy bodies, based on geochemical predictions of the ocean composition. In order to help improve our understanding of Europa's surface composition, we have conducted a study of frozen chloride-salt brines prepared under simulated Europa surface conditions (vacuum, temperature, and UV irradiation) using both near IR and Raman spectroscopies. Specifically, Raman spectroscopy was used to determine the hydration states of various chloride salts as a function of temperature. Near IR spectroscopy of identically prepared samples was used to provide reference reflectance spectra of the identified hydrated salts. Our results indicate that at temperatures ranging from 80 K to 233 K, hydrohalite is formed from the freezing of NaCl brines, while the freezing of KCl solutions does not form KCl hydrates. In addition, the freezing of MgCl2 solutions forms a stable hexahydrate, and the freezing of CaCl2 solutions forms a hexahydrate, a tetrahydrate, and a dihydrate. Dehydration of the salts was observed as temperatures were increased, leading to a succession of hydration states in the case of CaCl2.

  5. Modeling acid-gas generation from boiling chloride brines

    Directory of Open Access Journals (Sweden)

    Sonnenthal Eric

    2009-11-01

    Full Text Available Abstract Background This study investigates the generation of HCl and other acid gases from boiling calcium chloride dominated waters at atmospheric pressure, primarily using numerical modeling. The main focus of this investigation relates to the long-term geologic disposal of nuclear waste at Yucca Mountain, Nevada, where pore waters around waste-emplacement tunnels are expected to undergo boiling and evaporative concentration as a result of the heat released by spent nuclear fuel. Processes that are modeled include boiling of highly concentrated solutions, gas transport, and gas condensation accompanied by the dissociation of acid gases, causing low-pH condensate. Results Simple calculations are first carried out to evaluate condensate pH as a function of HCl gas fugacity and condensed water fraction for a vapor equilibrated with saturated calcium chloride brine at 50-150°C and 1 bar. The distillation of a calcium-chloride-dominated brine is then simulated with a reactive transport model using a brine composition representative of partially evaporated calcium-rich pore waters at Yucca Mountain. Results show a significant increase in boiling temperature from evaporative concentration, as well as low pH in condensates, particularly for dynamic systems where partial condensation takes place, which result in enrichment of HCl in condensates. These results are in qualitative agreement with experimental data from other studies. Conclusion The combination of reactive transport with multicomponent brine chemistry to study evaporation, boiling, and the potential for acid gas generation at the proposed Yucca Mountain repository is seen as an improvement relative to previously applied simpler batch evaporation models. This approach allows the evaluation of thermal, hydrological, and chemical (THC processes in a coupled manner, and modeling of settings much more relevant to actual field conditions than the distillation experiment considered. The actual

  6. Low temperature safety of lithium-thionyl chloride cells

    Science.gov (United States)

    Subbarao, S.; Deligiannis, F.; Shen, D. H.; Dawson, S.; Halpert, G.

    The use of lithium thionyl chloride cells for low-temperature applications is presently restricted because of their unsafe behavior. An attempt is made in the present investigation to identify the safe/unsafe low temperature operating conditions and to understand the low temperature cell chemistry responsible for the unsafe behavior. Cells subjected to extended reversal at low rate and -40 C were found to explode upon warm-up. Lithium was found to deposit on the carbon cathodes during reversal. Warming up to room temperature may be accelerating the lithium corrosion in the electrolyte. This may be one of the reasons for the cell thermal runaway.

  7. Reserve lithium-thionyl chloride battery for missile applications

    Science.gov (United States)

    Planchat, J. P.; Descroix, J. P.; Sarre, G.

    A comparative performance study has been conducted for silver-zinc, thionyl chloride, and thermal batteries designed for such missile applications as ICBM guidance system power supplies. Attention is given to each of the three candidates' conformity to requirements concerning mechanical configuration, electrochemical design, electrolyte reservoir, external case, and gas generator. The silver-zinc and Li-SOCl2 candidates employ similar cell configurations and yield comparable performance. The thermal battery is found to be incapable of meeting battery case temperature-related requirements.

  8. Optimization of reserve lithium thionyl chloride battery electrochemical design parameters

    Science.gov (United States)

    Doddapaneni, N.; Godshall, N. A.

    The performance of Reserve Lithium Thionyl Chloride (RLTC) batteries was optimized by conducting a parametric study of seven electrochemical parameters: electrode compression, carbon thickness, presence of catalyst, temperature, electrode limitation, discharge rate, and electrolyte acidity. Increasing electrode compression (from 0 to 15 percent) improved battery performance significantly (10 percent greater carbon capacity density). Although thinner carbon cathodes yielded less absolute capacity than did thicker cathodes, they did so with considerably higher volume efficiencies. The effect of these parameters, and their synergistic interactions, on electrochemical cell performance is illustrated.

  9. Pulse Capability of the AIRI Lead Chloride Electrode.

    Science.gov (United States)

    1979-11-01

    au PbC12 constituaient un autre grave inconvenient par rapport aux filectrodes au chiorure d’argent. Les glectrodes au chlorure de plomb n’offraient...aucun avantage r6el par rapport aux ilectrodes au chlorure d’argent. Tout travail ult~rieur portent sur la mise en point d’Alectrodes au chlorure de...source now in use is a seawater-activated battery in which the anode is a magnesium alloy and the cathode a silver chloride electrode. These batteries

  10. Effects of chloride and silver ions on gold nanorod formation

    Science.gov (United States)

    Ock Park, Jin; Cho, So-Hye; Jeong, Dae-Yong; Kong, Young-Min; Lee, Seung Yong

    2015-01-01

    The ability to tune the longitudinal localized surface plasmon resonance of gold nanorods (AuNRs) via simple modification of their aspect ratio is a large contributing factor to their widespread use across multiple fields. An understanding of the synthesis conditions that affect the aspect ratio and yield of AuNRs is therefore of utmost importance. From this perspective, we take a systematic approach in investigating the effect of the following conditions on the seed-mediated formation of AuNRs: the addition of chloride or silver ions, and the use of a hexadecyltrimethylammonium bromide (CTAB) source with different levels of effectiveness on controlling the shape of growing AuNRs.

  11. Anaphylactic reaction following administration of nose drops containing benzalkonium chloride

    Directory of Open Access Journals (Sweden)

    Mezger Elke

    2012-10-01

    Full Text Available Abstract We describe a case of anaphylactic reaction in a 46-year-old female post application of decongestant nose drops containing benzalkonium chloride (BAC. With some latency, the patient complained of cough, dyspnea, sensation of heat, croakiness and pruritus. Since she showed all of these symptoms, typical of an anaphylactic reaction, we proceeded some weeks later with a prick test with solutions containing BAC, a cationic surfactant commonly used as an antibacterial preservative in many medical solutions. The prick test was positive, confirming the assumption of a hypersensitive reaction to BAC.

  12. Anaphylactic reaction following administration of nose drops containing benzalkonium chloride

    Science.gov (United States)

    2012-01-01

    We describe a case of anaphylactic reaction in a 46-year-old female post application of decongestant nose drops containing benzalkonium chloride (BAC). With some latency, the patient complained of cough, dyspnea, sensation of heat, croakiness and pruritus. Since she showed all of these symptoms, typical of an anaphylactic reaction, we proceeded some weeks later with a prick test with solutions containing BAC, a cationic surfactant commonly used as an antibacterial preservative in many medical solutions. The prick test was positive, confirming the assumption of a hypersensitive reaction to BAC. PMID:23078861

  13. Multireference Calculation of the Photodissociation of Benzyl Chloride

    Institute of Scientific and Technical Information of China (English)

    CAO Jun; LIU Ya-Jun; FANG Wei-Hai

    2007-01-01

    The photodissociation mechanism of benzyl chloride (BzCl) under 248 nm has been investigated by the complete active space SCF (CASSCF) method by calculating the geometries of the ground (S0) and lower excited states,the vertical (Tv) and adiabatic (T0) excitation energies of the lower states,and the dissociation reaction pathways on the potential energy surfaces (PES) of S1, T1 and T2 states.The calculated results clearly elucidated the photodissociation mechanism of BzCl,and indicated that the photodissociation on the PES of T1 state is the most favorable.

  14. Calorimetry of 25 Ah lithium/thionyl chloride cells

    Science.gov (United States)

    Johnson, C. J.; Dawson, S.

    1991-01-01

    Heat flow measurements of 25-Ah lithium thionyl chloride cells provided a method to calculate an effective thermal potential, E(TP) of 3.907 V. The calculation is useful to determine specific heat generation of this cell chemistry and design. The E(TP) value includes heat generation by electrochemical cell reactions, competitive chemical reactions, and resistance heating at the tabs, connectors, and leads. Heat flow was measured while applying electrical loads to the cell in an isothermal calorimeter set at 0, 20, and 60 C.

  15. Synthesis of brookite-typed titania from titanium chloride solution

    Institute of Scientific and Technical Information of China (English)

    Satoshi OKANO; Saeki YAMAMURO; Toshiro TANAKA

    2009-01-01

    The brookite-phase TiO2 was prepared by a hydrothermal synthesis of titanium chloride solution. The thermolysis time and the pH value of the solution were controlled during the synthesis. X-ray diffraction experiments showed that TiO2 powders partially containing the brookite-phase were successfully ob-tained. A great amount of OH in the reaction solution was found to be important to obtain the brookite phase because the intermediate complex leading to the brookite phase consumes more OH- than other phases like the rutile.

  16. Synthesis of brookite-typed titania from titanium chloride solution

    Institute of Scientific and Technical Information of China (English)

    Satoshi; OKANO; Saeki; YAMAMURO; Toshiro; TANAKA

    2009-01-01

    The brookite-phase TiO2 was prepared by a hydrothermal synthesis of titanium chloride solution. The thermolysis time and the pH value of the solution were controlled during the synthesis. X-ray diffraction experiments showed that TiO2 powders partially containing the brookite-phase were successfully obtained. A great amount of OH-in the reaction solution was found to be important to obtain the brookite phase because the intermediate complex leading to the brookite phase consumes more OH- than other phases like the rutile.

  17. Involvement of chloride in renin secretion from isolated rat glomeruli

    DEFF Research Database (Denmark)

    Skøtt, O; Jensen, B L

    1992-01-01

    M) inhibited renin release reversibly. Substitution of Cl- with nitrate (101 mM) stimulated renin secretion. Substitution with iodide (15 or 101 mM) had no consistent effect. The stimulation induced by calcium-free solutions was high in May and low in September. In the absence of chloride, the response....... It is concluded that the renin secretory process has a demand for permeant anions. The stimulation caused by low external calcium involves at least two mechanisms: one is anion sensitive, powerful, varies with the season, and includes a recruitment phenomenon; another is anion insensitive and weak....

  18. Measurement of urinary chloride with the Kodak Ektachem 400.

    Science.gov (United States)

    Melhem, M F; Seltman, H; Sanghvi, A

    1985-04-01

    Urinary chloride can be measured simply, precisely, and accurately with the Ektachem 400 clinical chemistry analyzer. Because the coated film technique used in this instrument requires the presence of a protein matrix, we added a protein-based calibrator to the urine samples to overcome the low protein concentration in these specimens. Its advantages over a coulometric titration method (Astra analyzer) include the extension of the range of linearity to lower concentrations and the absence of interference from prednisone metabolites in urine. A disadvantage is the negative bias interference of allopurinol.

  19. Corrosion Inhibition of Carbon Steel in Chloride and Sulfate Solutions

    Directory of Open Access Journals (Sweden)

    Amr Ahmed Elsayed

    2016-02-01

    Full Text Available Corrosion is a major problem in industry and in infrastructure; a huge sum of expenditure every year is spent on preventing, retarding, and repairing its damages. This work studies the engineering of an inhibitor for carbon steel metal used in the cooling systems containing high concentration of chloride and sulfate ions. For this purpose, the synergy between the dichromate, molybdate and nitrite inhibitors is examined and optimized to the best results. Moreover, care was taken that the proposed inhibitor is compliant with the environmental laws and regulations.

  20. THE INFLUENCE OF CALCIUM CHLORIDE UPON EXPERIMENTAL BOTULISM.

    Science.gov (United States)

    Hall, I C; Davis, N C

    1923-03-31

    1. Calcium chloride given subcutaneously, intraperitoneally, or intravenously has been found to have no effect upon the production of botulism following the injection of Bacillus botulinus (Strain 80B) into the peritoneal cavity of guinea pigs. 2. Treatment of Bacillus botulinus with alcohol has been found markedly to decrease its toxicity for guinea pigs. This is in conformity with the work of Bronfenbrenner and Schlesinger. 3. Toxin-free spores of Bacillus botulinus have been found pathogenic for guinea pigs. 4. No prejudice as to possible results in rabbits should be based upon the above conclusions.

  1. The Humidity Sensor Using the Polyacrylic Emulsion Containing Magnesium Chloride

    Institute of Scientific and Technical Information of China (English)

    Ching-Han Yu; Jung-Chuan Chou; Tai-Ping Sun; Shen-Kan Hsiung

    2006-01-01

    An impedance type humidity sensor based on the polyacrylic emulsion containing magnesium chloride (MgCl2)without chemical modification was investigated. The impedances of the sensor were measured from various relative humidity in the frequency range between 0.1kHz and 100 kHz. The sensor has a good sensitivity from 60%RH to 90%RH. According to the experimental results, the response time is about 240 seconds in the adsorption process and 310 seconds in the desorption process.

  2. Antiviral effect of lithium chloride on infection of cells by canine parvovirus.

    Science.gov (United States)

    Zhou, Pei; Fu, Xinliang; Yan, Zhongshan; Fang, Bo; Huang, San; Fu, Cheng; Hong, Malin; Li, Shoujun

    2015-11-01

    Canine parvovirus type 2 causes significant viral disease in dogs, with high morbidity, high infectivity, and high mortality. Lithium chloride is a potential antiviral drug for viruses. We determined the antiviral effect of Lithium Chloride on canine parvovirus type 2 in feline kidney cells. The viral DNA and proteins of canine parvovirus were suppressed in a dose-dependent manner by lithium chloride. Further investigation verified that viral entry into cells was inhibited in a dose-dependent manner by lithium chloride. These results indicated that lithium chloride could be a potential antiviral drug for curing dogs with canine parvovirus infection. The specific steps of canine parvovirus entry into cells that are affected by lithium chloride and its antiviral effect in vivo should be explored in future studies.

  3. The influence of the blast furnace slag replacement on chloride penetration in concrete

    Directory of Open Access Journals (Sweden)

    Juan Lizarazo Marriaga

    2011-05-01

    Full Text Available  Corrosion of steel reinforcement due to chloride penetration is the greatest cause of durability problems in concrete; intense international research has been carried out to understand and avoid this. This paper summarises the results of a theoretical and experimental research programme investigating the influence of blast furnace slag on chloride-related transport properties. The relationship between the apparent chloride diffusion coefficient, electrical resistivity and compressive strength was measured. Chloride, hydroxide, sodium and potassium’s intrinsic diffusion coefficients were obtained by using a computational model and an electrical migration test. The initial hydroxide composition of the pore solution, porosity and chloride binding capacity were also determined from the model. The results showed that blast furnace slag improved chloride penetration resistance, resulting in concrete which was less vulnerable to corrosion. 

  4. Studies Leading to the Development of High-Rate Lithium Sulfuryl Chloride Battery Technology.

    Science.gov (United States)

    1982-09-01

    greatest attention has been given to the lithium - thionyl chloride (Li/SOC12 ) system. Cells and batteries have been demonstrated with energy densities...Studies Leading to the Development of High-Rate Lithium Sulfuryl Chloride Battery Technology John C. Hall and Mark Koch Gould Research Center, Materials...High-Rate 11182to 33182 Lithium -Sulfuryl Chloride Battery Technology 1_1/82_to_3/31/82 S. PERFORMING ORO. REPORT NUMBER 2 7. AUTHOR(*) S. CONTRACT OR

  5. In-depth analysis of chloride treatments for thin-film CdTe solar cells

    OpenAIRE

    Major, J.D.; Al Turkestani, M.; Bowen, L; Brossard, M.; Li, C; Lagoudakis, P.; S. J. Pennycook; Phillips, L. J.; Treharne, R. E.; Durose, K.

    2016-01-01

    CdTe thin-film solar cells are now the main industrially established alternative to silicon-based photovoltaics. These cells remain reliant on the so-called chloride activation step in order to achieve high conversion efficiencies. Here, by comparison of effective and ineffective chloride treatments, we show the main role of the chloride process to be the modification of grain boundaries through chlorine accumulation, which leads an increase in the carrier lifetime. It is also demonstrated th...

  6. Enhanced expression of potassium-chloride cotransporter KCC2 in human temporal lobe epilepsy

    OpenAIRE

    Karlócai, MR; Wittner, L; Tóth, K; Maglóczky, Z.; Katarova, Z.; Rásonyi, G; Erőss, L; Czirják, S; Halász, P; G. Szabó; Payne, JA; Kaila, K.; Freund, TF

    2015-01-01

    © 2015 Springer-Verlag Berlin Heidelberg Synaptic reorganization in the epileptic hippocampus involves altered excitatory and inhibitory transmission besides the rearrangement of dendritic spines, resulting in altered excitability, ion homeostasis, and cell swelling. The potassium-chloride cotransporter-2 (KCC2) is the main chloride extruder in neurons and hence will play a prominent role in determining the polarity of GABAA receptor-mediated chloride currents. In addition, KCC2 also interact...

  7. Investigation of factors affecting the accumulation of vinyl chloride in polyvinyl chloride piping used in drinking water distribution systems.

    Science.gov (United States)

    Walter, Ryan K; Lin, Po-Hsun; Edwards, Marc; Richardson, Ruth E

    2011-04-01

    Plastic piping made of polyvinyl chloride (PVC), and chlorinated PVC (CPVC), is being increasingly used for drinking water distribution lines. Given the formulation of the material from vinyl chloride (VC), there has been concern that the VC (a confirmed human carcinogen) can leach from the plastic piping into drinking water. PVC/CPVC pipe reactors in the laboratory and tap samples collected from consumers homes (n = 15) revealed vinyl chloride accumulation in the tens of ng/L range after a few days and hundreds of ng/L after two years. While these levels did not exceed the EPA's maximum contaminant level (MCL) of 2 μg/L, many readings that simulated stagnation times in homes (overnight) exceeded the MCL-Goal of 0 μg/L. Considerable differences in VC levels were seen across different manufacturers, while aging and biofilm effects were generally small. Preliminary evidence suggests that VC may accumulate not only via chemical leaching from the plastic piping, but also as a disinfection byproduct (DBP) via a chlorine-dependent reaction. This is supported from studies with CPVC pipe reactors where chlorinated reactors accumulated more VC than dechlorinated reactors, copper pipe reactors that accumulated VC in chlorinated reactors and not in dechlorinated reactors, and field samples where VC levels were the same before and after flushing the lines where PVC/CPVC fittings were contributing. Free chlorine residual tests suggest that VC may be formed as a secondary, rather than primary, DBP. Further research and additional studies need to be conducted in order to elucidate reaction mechanisms and tease apart relative contributions of VC accumulation from PVC/CPVC piping and chlorine-dependent reactions.

  8. The contribution of histamine release to bronchoconstriction provoked by inhaled benzalkonium chloride in asthma.

    Science.gov (United States)

    Miszkiel, K A; Beasley, R; Rafferty, P; Holgate, S T

    1988-01-01

    1. To investigate the possibility that benzalkonium chloride-induced bronchoconstriction results from the endogenous release of histamine, we examined the effect of the selective histamine antagonists terfenadine and astemizole, on the airways response to inhaled benzalkonium chloride and histamine in 12 asthmatic subjects. 2. Double-blind concentration- and time-course studies were undertaken, 3 h after treatment with terfenadine or matched placebo. 3. Benzalkonium chloride and histamine caused concentration-related falls in FEV1 in all subjects with benzalkonium chloride being 7.4 times less potent as a bronchoconstrictor agonist than histamine. Terfenadine displaced to the right the benzalkonium chloride and histamine concentration-response curves by 3.7 and 111 fold respectively. Terfenadine attenuated the initial (5 min) bronchoconstrictor response to benzalkonium chloride by 40%. However, over the whole 45 min period, the response was reduced by only 13% compared with 86% inhibition of the response to histamine. 4. In an open study, eight of the 12 subjects undertook a time course study with inhaled benzalkonium chloride after pretreatment with the chemically unrelated histamine antagonist astemizole. Astemizole inhibited benzalkonium chloride-induced bronchoconstriction to an almost identical degree as that achieved with terfenadine. 5. We conclude that the initial bronchoconstrictor effect of benzalkonium chloride is due, in part, to histamine release. However, the majority of the adverse effect relates to other, as yet unrecognised effects of this bacteriocidal substance. PMID:2451929

  9. Influence of chloride on the chronic toxicity of sodium nitrate to Ceriodaphnia dubia and Hyalella azteca.

    Science.gov (United States)

    Soucek, David J; Dickinson, Amy

    2016-09-01

    While it has been well established that increasing chloride concentration in water reduces the toxicity of nitrite to freshwater species, little work has been done to investigate the effect of chloride on nitrate toxicity. We conducted acute and chronic nitrate (as sodium nitrate) toxicity tests with the cladoceran Ceriodaphnia dubia and the amphipod Hyalella azteca (chronic tests only) over a range of chloride concentrations spanning natural chloride levels found in surface waters representative of watersheds of the Great Lakes Region. Chronic nitrate toxicity test results with both crustaceans were variable, with H. azteca appearing to be one of the more sensitive invertebrate species tested and C. dubia being less sensitive. While the variability in results for H. azteca were to an extent related to chloride concentration in test water that was distinctly not the case for C. dubia. We concluded that the chloride dependent toxicity of nitrate is not universal among freshwater crustaceans. An additional sodium chloride chronic toxicity test with the US Lab strain of H. azteca in the present study suggested that when present as predominantly sodium chloride and with relatively low concentrations of other ions, there is a narrow range of chloride concentrations over which this strain is most fit, and within which toxicity test data are reliable.

  10. On the Durability of Sealable Circular Concrete Structures under Chloride Environment

    Directory of Open Access Journals (Sweden)

    Changwen Mi

    2015-01-01

    Full Text Available Reinforcement corrosion resulting from chloride attack is one major mechanism that compromises concrete durability. Numerical methods were commonly used for tackling Fick’s diffusion equations. In this paper, we developed a Crank-Nicolson based finite difference scheme suitable for circular concrete structures. Both a time-dependent surface chloride model and diffusivity were considered. The impact of an ideal sealer on chloride redistribution was further investigated. Results suggested that the chloride threshold depth in a concrete structure is greatly affected by the radius of curvature, environment severity, and diffusivity. For sealable concrete structures, both the sealer application timing and location are of great importance.

  11. Response to comments on "Local impermeant anions establish the neuronal chloride concentration"

    DEFF Research Database (Denmark)

    Glykys, J; Dzhala, V; Egawa, K

    2014-01-01

    We appreciate the interest in our paper and the opportunity to clarify theoretical and technical aspects describing the influence of Donnan equilibria on neuronal chloride ion (Cl(-)) distributions....

  12. Protective effect and mechanism of lithium chloride pretreatment on myocardial ischemia-reperfusion injury in rats

    Institute of Scientific and Technical Information of China (English)

    Fang-Jiang Li; Tao Hsu; Hui-Xian Li; Jin-Zheng Shi; Mei-Ling Du; Xiao-Yuan Wang; Wen-Ting Zhang

    2014-01-01

    Objective:To investigate the protective effect and mechanism of lithium chloride pretreatment on myocardial ischemia-reperfusion injury(I-RI) in rats.Methods:A total of60SD rats were randomly divided into control group, model group, lithium chloride intervention group and L-arginine methyl ester+ lithium chloride intervention group with15 in each.TheI-RI model was established in model group, the lithium chloride intervention group andL-arginine methyl ester+ lithium chloride intervention group by method of seaming along left anterior descending coronary artery myocardial, control group was only opened the chest without seaming,ST-elevation within2 min was regarded as modeling success.Model group did not adopted any intervention, lithium chloride intervention group was treated with lithium chloride injection 15 mg/kg by jugular venipuncture preoperatively,L-arginine methyl ester+ lithium chloride intervention group was treated with intraperitoneal injection of30 mg•kg-1•d-1L-arginine methyl ester7 d before the test, and intravenous catheter of15 mg/kg lithium chloride preoperatively. The hydroxybutyric acid dehydrogenase(HBDH), creatine kinase isoenzyme(CK-MB), superoxide dismutase(SOD), malondialdehyde(MDA) level and nitric oxide synthase(NOS) activites were tested.Each large area of myocardial ischemia tissue was extracted for determination of the MDA content,SOD activity in tissue and serum, and morphological changes of myocardial tissue.Results:SOD activity was highest in lithium chloride intervention group, followed by L-arginine methyl ester+ lithium chloride intervention group, control group and model group (P0.05);HBDH andCK-MB of plasma were highest in model group, followed byL-arginine methyl ester+ lithium chloride intervention group, lithium chloride intervention group and control group(P<0.05).A significantly lighter myocardial damage was observed microscopically in lithium chloride intervention group than that inL-arginine methyl ester+ lithium

  13. A high power lithium thionyl chloride battery for space applications

    Science.gov (United States)

    Shah, Pinakin M.

    1993-03-01

    A high power, 28 V, 330 A h, active lithium thionyl chloride battery has been developed for use as main and payload power sources on an expendable launch vehicle. Nine prismatic cells, along with the required electrical components and a built-in heater system, are efficiently packaged resulting in significant weight savings over presently used silver-zinc batteries. The high rate capability is achieved by designing the cells with a large electrochemical surface area and impregnating an electrocatalyst, polymeric phthalocyanine, into the carbon cathodes. Passivation effects are reduced with the addition of sulfur dioxide into the thionyl chloride electrolyte solution. The results of conducting a detailed thermal analysis are utilized to establish the heater design parameters and the thermal insulation requirements of the battery. An analysis of cell internal pressure and vent characteristics clearly illustrates the margins of safety under different operating conditions. Performance of fresh cells is discussed using polarization scan and discharge data at different rates and temperatures. Self-discharge rate is estimated based upon test results on cells after storage. Results of testing a complete prototype battery are described.

  14. Benzotriazole as an inhibitor of brass corrosion in chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Kosec, Tadeja [Jozef Stefan Institute, Department of Physical and Organic Chemistry, Jamova 39, 1000 Ljubljana (Slovenia); Milosev, Ingrid [Jozef Stefan Institute, Department of Physical and Organic Chemistry, Jamova 39, 1000 Ljubljana (Slovenia); Orthopaedic Hospital Valdoltra, Jadranska c. 31, 6280 Ankaran (Slovenia)], E-mail: ingrid.milosev@ijs.si; Pihlar, Boris [Faculty of Chemistry and Chemical Technology, University of Ljubljana, Askerceva 5, 1000 Ljubljana (Slovenia)

    2007-09-15

    The current research explores the formation of protective layers on copper, zinc and copper-zinc (Cu-10Zn and Cu-40Zn) alloys in chloride solution containing benzotriazole (BTAH), by use of electrochemical techniques, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). Electrochemical reactions and surface products formed at the open circuit potential and as a function of the potential range are discussed. The addition of benzotriazole to aerated, near neutral 0.5 M NaCl solution affects the dissolution of copper, zinc, Cu-10Zn and Cu-40Zn alloys. The research also compares the inhibition efficiency and Gibbs adsorption energies of the investigated process. Benzotriazole, generally known as an inhibitor of copper corrosion is also shown to be an efficient inhibitor for copper-zinc alloys and zinc metal. The surface layer formed on alloys in BTAH-inhibited solution comprised both oxide and polymer components, namely Cu{sub 2}O and ZnO oxides, and Cu(I)-BTA and Zn(II)-BTA polymers. The formation of this mixed copper-zinc oxide polymer surface film provides an effective barrier against corrosion of both metal components in chloride solution.

  15. EVALUATION OF FUNGICIDAL EFFICIENEY OF IRANIAN MADE BENZALKONIUM CHLORIDE

    Directory of Open Access Journals (Sweden)

    K. Imandel

    1995-12-01

    Full Text Available Fungicidal efficiency of Iranian made benzalkonium chloride named Akhgar, Afshang and Hamoon were evaluated on pure culture species of Aspergillus nijer, Candida ablicans and Mucour according to the standard method No. 2442 issued by the Institute of Standards and Industrial Research of Iran, from October 1993 to March 1994. Suspensions were prepared in a way that each cubic centimeter having 3.5×107 condia of Aspergillus nijer, 4×107 Candida albicans yeast cell and 2×107 Mucour spore, and Improved Neubauer slide counting cell were used for enumeration. These laboratory study showed that Lecithine and Tween were the best neutralizers with equal power. Usage of five dilutions of 0.4, 0.6, 0.8, 1 fungus separately at 6.5 to 6.7 pH, confirmed the correctness of dilution figure of 0.4 percent proposed by producer companies and showed that these fungi are still sensitive against Benzalkonium Chloride disinfectants.

  16. Coagulation properties of anelectrochemically prepared polyaluminum chloride containing active chlorine

    Institute of Scientific and Technical Information of China (English)

    HU Chengzhi; LIU Huijuan; QU Jiuhui

    2006-01-01

    With high content of the Al13 species and the active chloride, an electrochemically prepared polyaluminum chloride (E-PACl) presents integrated efficiency of coagulation and oxidation. The coagulation properties of E-PACl were systemically investigated through jar tests in the various water quality conditions. The active chlorine in E-PACl can significantly influence the coagulation behavior due to the active chlorine preoxidation, which can change the surface charge characteristic of organic matter (OM) in water. The active chlorine preoxidation could improve the E-PACl coagulation efficiency if the water possessed the characteristics of relatively low OM content (2 mg/L) and high hardness (278 mg CaCO3/L). In the water with medium content of OM (5 mg/L), dosage would be a crucial factor to decide whether the active chlorine in E-PACl aided coagulation process or not. Comparing with alkaline condition, active chlorine would show a more significant influence on the coagulation process in acidic region.

  17. Leaching of complex sulphide concentrate in acidic cupric chloride solutions

    Institute of Scientific and Technical Information of China (English)

    M. TCHOUMOU; M. ROYNETTE

    2007-01-01

    The chemical analysis of a complex sulphide concentrate by emission spectrometry and X-ray diffraction shows that it contains essentially copper, lead, zinc and iron in the form of chalcopyrite, sphalerite and galena. A small amount of pyrite is also present in the ore but does not be detected with X-ray diffraction. The cupric chloride leaching of the sulphide concentrate at various durations and solid/liquid ratios at 100 ℃ shows that the rate of dissolution of the ore is the fastest in the first several hours, and after 12 h it does not evolve significantly. If oxygen is excluded from the aqueous cupric chloride solution during the leaching experiment at 100 ℃, the pyrite in the ore will not be leached. The determination of principal dissolved metals in the leaching liquor by flame atomic absorption spectrometry, and the chemical analysis of solid residues by emission spectrometry and X-ray diffraction allow to conclude that the rate of dissolution of the minerals contained in the complex sulphide concentrate are in the order of galena>sphalerite>chalcopyrite.

  18. Role for acetotrophic methanogens in methanogenic biodegradation of vinyl chloride

    Science.gov (United States)

    Bradley, P.M.; Chapelle, F.H.

    1999-01-01

    Under methanogenic conditions, stream-bed sediment microorganisms rapidly degraded [1,2-14C]vinyl chloride to 14CH4 and 14CO2. Amendment with 2-bromoethanesulfonic acid eliminated 14CH4 production and decreased 14CO2 recovery by an equal molar amount. Results obtained with [14C]ethene, [14C]acetate, or 14CO2 as substrates indicated that acetotrophic methanogens were responsible for the production of 14CH4 during biodegradation of [1,2-14C]VC.Under methanogenic conditions, stream-bed sediment microorganisms rapidly degraded [1,2-14C]vinyl chloride to 14CH4 and 14CO2. Amendment with 2-bromoethanesulfonic acid eliminated 14CH4 production and decreased 14CO2 recovery by an equal molar amount. Results obtained with [14C]-ethene, [14C]acetate, or 14CO2 as substrates indicated that acetotrophic methanogens were responsible for the production of 14CH4, during biodegradation of [1,2-14C]VC.

  19. Formulation and Characterization of Cetylpyridinium Chloride Bioadhesive Tablets

    Directory of Open Access Journals (Sweden)

    Jafar Akbari

    2014-12-01

    Full Text Available Purpose: Bioadhesive polymers play an important role in biomedical and drug delivery applications. The aim of this study is to develop a sustained- release tablet for local application of Cetylpyridinium Chloride (CPC. This delivery system would supply the drug at an effective level for a long period of time, and thereby overcome the problem of the short retention time of CPC and could be used for buccal delivery as a topical anti-infective agent. Methods: CPC bioadhesive tablets were directly prepared using 7 mm flat-faced punches on a hydraulic press. The materials for each tablet were weighted, introduced into the die and compacted at constant compression pressure. The dissolution tests were performed to the rotation paddle method and the bioadhesive strength of the tablets were measured. Results: The results showed that as the concentration of polymer increased, the drug release rate was decreased. Also the type and ratio of polymers altered the release kinetic of Cetylpyridinium Chloride from investigated tablets. The bioadhesion strength increased with increasing the concentration of polymer and maximum bioadhesion strength was observed with HPMC K100M. Conclusion: The selected formulation of CPC bioadhesive tablet can be used as a suitable preparation for continuous release of CPC with appropriate bioadhesion strength.

  20. Influence of sodium chloride on wine yeast fermentation performance

    Directory of Open Access Journals (Sweden)

    Stilianos Logothetis

    2010-06-01

    Full Text Available Stilianos Logothetis1, Elias T Nerantzis2, Anna Gioulioti3, Tasos Kanelis2, Tataridis Panagiotis2, Graeme Walker11University of Abertay Dundee, School of Contemporary Sciences, Dundee, Scotland; 2TEI of Athens Department of Oenology and Spirit Technology, Biotechnology and Industrial Fermentations Lab Agiou Spiridonos, Athens, Greece; 3Ampeloiniki SA Industrial Park Thermi, Thessaloniki, GreeceAbstract: This paper concerns research into the influence of salt (sodium chloride on growth, viability and fermentation performance in a winemaking strain of the yeast, Saccharomyces cerevisiae. Experimental fermentations were conducted in both laboratory-scale and industrial-scale experiments. Preculturing yeasts in elevated levels of sodium chloride, or salt “preconditioning” led to improved fermentation performance. This was manifest by preconditioned yeasts having an improved capability to ferment high-sugar containing media with increased cell viability and with elevated levels of produced ethanol. Salt-preconditioning most likely influenced the stress-tolerance of yeasts by inducing the synthesis of key metabolites such as trehalose and glycerol. These compounds may act to improve cells’ ability to withstand osmostress and ethanol toxicity during fermentations of grape must. Industrial-scale trials using salt-preconditioned yeasts verified the benefit of this novel physiological cell engineering approach to practical winemaking fermentations.Keywords: salt, preconditioning, fermentation performance, Saccharomyces cerevisiae, wine

  1. Effect of Mercuric Chloride on Kinetic Properties of Horseradish Peroxidase

    Directory of Open Access Journals (Sweden)

    N Einollahi

    2006-06-01

    Full Text Available Mercury is one of the three major environmental metal poisons, and mercuric chloride is a highly reactive compound which can harm cells by a variety of mechanisms including direct interaction with sulphydryl groups of proteins and enzymes, therefore affecting the enzymatic activity. This study focused on the effect of Hg++ on horseradish peroxidase (donor: hydrogen peroxide oxidoreductase, EC 1.11.1.7 (HRP (Isoenzyme C activity. In the presence of 88 mM hydrogen peroxide Km for o-dianisidine oxidation was 0.05 millimolar and Vmax was 8.5 M.s-1. Incubation of the enzyme with 1 to 100 millimolar mercuric chloride for 5-20- and 60 min resulted in progressive inhibition of the enzymatic activity. At low Hg++ concentrations the inhibition was reversible by excess substrate, while at high Hg++ concentration the inhibition was not reversible. Results also indicated that the type of inhibition depended on the duration of incubation of the enzyme with metal ion and on the Hg++ concentration. So we could conclude that the type of inhibition changed from noncompetitive to mix with increased incubation time and increased metal concentration.

  2. Large Scale Synthesis of Carbon Nanofibres on Sodium Chloride Support

    Directory of Open Access Journals (Sweden)

    Ravindra Rajarao

    2012-06-01

    Full Text Available Large scale synthesis of carbon nanofibres (CNFs on a sodium chloride support has been achieved. CNFs have been synthesized using metal oxalate (Ni, Co and Fe as catalyst precursors at 680 C by chemical vapour deposition method. Upon pyrolysis, this catalyst precursors yield catalyst nanoparticles directly. The sodium chloride was used as a catalyst support, it was chosen because of its non‐toxic and water soluble nature. Problems, such as the detrimental effect of CNFs, the detrimental effects on the environment and even cost, have been avoided by using a water soluble support. The structure of products was characterized by scanning electron microscopy, transmission electron microscopy and Raman spectroscopy. The purity of the grown products and purified products were determined by the thermal analysis and X‐ray diffraction method. Here we report the 7600, 7000 and 6500 wt% yield of CNFs synthesized over nickel, cobalt and iron oxalate. The long, curved and worm shaped CNFs were obtained on Ni, Co and Fe catalysts respectively. The lengthy process of calcination and reduction for the preparation of catalysts is avoided in this method. This synthesis route is simple and economical, hence, it can be used for CNF synthesis in industries.

  3. Thyrotoxicity of the Chlorides of Cadmium and Mercury in Rabbit

    Institute of Scientific and Technical Information of China (English)

    NINAGHOSH; SHELLEYBHATTACHARYA

    1992-01-01

    Exposure to heavy metals such as cadmium and mercury is of immediate environmental concern.The present study was aimed at establishing a direct relationship between heavy metal poisoning and thyroid dysfunction.Cadmium and mercury treatment at LD50 levels resulted in severe thyrotoxicosis in the rabbit.Within 24h of intramuscular administration of cadmium chloride 15 mg·kg-1 body weight(bw)and mercury chloride20mg·kg-1 bw,thyroid peroxidase activity increased significantly over the control with a concomitant rise in the triiodothyronie(T3)titre.On the other hand,there was a remarkable fall in the thyroxine(T4)level,and the T3,T4 ratio was high as compared with the control.Evidence indicates that acute heavy metal lethality will induce immediate hyperthyroidism.It is suggested that T3-toxicosis may be produced by a preferential synthesis of T3 and/or preferential deiodination of T4 to T3.Measurement of T3 and T4 levels may thus e utilized as a reliable indicator of heavy metal lethality.

  4. Gadolinium chloride pretreatment ameliorates acute cadmium-induced hepatotoxicity.

    Science.gov (United States)

    Kyriakou, Loukas G; Tzirogiannis, Konstantinos N; Demonakou, Maria D; Kourentzi, Kalliopi T; Mykoniatis, Michael G; Panoutsopoulos, Georgios I

    2013-08-01

    Cadmium is a known industrial and environmental pollutant. It causes hepatotoxicity upon acute administration. Features of cadmium-induced acute hepatoxicity encompass necrosis, apoptosis, peliosis and inflammatory infiltration. Gadolinium chloride (GdCl3) may prevent cadmium-induced hepatotoxicity by suppressing Kupffer cells. The effect of GdCl3 pretreatment on a model of acute cadmium-induced liver injury was investigated. Male Wistar rats 4-5 months old were injected intraperitoneally with normal saline followed by cadmium chloride (CdCl2; 6.5 mg/kg) or GdCl3 (10 mg/kg) followed by CdCl2 (6.5 mg/kg; groups I and II, respectively). Rats of both the groups were killed at 9, 12, 16, 24, 48 and 60 h after cadmium intoxication. Liver sections were analyzed for necrosis, apoptosis, peliosis and mitoses. Liver regeneration was also evaluated by tritiated thymidine incorporation into hepatic DNA. Serum levels of aspartate aminotransferase (AST) and alanine aminotransferase (ALT) were also determined. Hepatic necrosis, hepatocyte and nonparenchymal cell apoptosis and macroscopic and microscopic types of peliosis hepatis were minimized by gadolinium pretreatment. Serum levels of AST and ALT were also greatly diminished in rats of group II. Tritiated thymidine incorporation into hepatic DNA was increased in gadolinium pretreatment rats. Kupffer cell activation was minimal in both the groups of rats. Gadolinium pretreatment attenuates acute cadmium-induced liver injury in young Wistar rats, with mechanisms other than Kupffer cell elimination.

  5. Intravesical oxybutinin chloride in children with intermittent catheterization: sonographic findings.

    Science.gov (United States)

    Zerin, J M; DiPietro, M A; Ritchey, M L; Bloom, D A

    1994-01-01

    The sonographic findings in the bladder are presented in four children with myelomeningocele and neurogenic dysfunction of the bladder, who were treated with intermittent self-catheterization and intravesical oxybutinin chloride. All were referred for routine sonography of the urinary tract. Each had infused a crushed tablet of oxybutinin chloride intravesically 30-120 min before the examination. In two children, brightly echogenic, non-shadowing particles were suspended in the bladder urine. In one of these, the particles swirled giving the impression of a "snowstorm"; in the other, most of the particles gradually settled forming an irregular clump on the bladder base. In the remaining two children, the urine appeared diffusely hazy with innumerable tiny particles giving the impression of a fine mist filling the bladder. The sonographic appearance of the urine in the bladder after intravesical instillation of crushed tablets can be dramatic and can simulate pus, blood, fungus, or other debris in the bladder lumen. In the absence of clinical symptoms or hematuria, a history of recent infusion of medication into the bladder should be sought.

  6. Formulation and Characterization of Cetylpyridinium Chloride Bioadhesive Tablets

    Science.gov (United States)

    Akbari, Jafar; Saeedi, Majid; Morteza-Semnani, Katayoun; Kelidari, Hamidreza; Lashkari, Maryam

    2014-01-01

    Purpose: Bioadhesive polymers play an important role in biomedical and drug delivery applications. The aim of this study is to develop a sustained- release tablet for local application of Cetylpyridinium Chloride (CPC). This delivery system would supply the drug at an effective level for a long period of time, and thereby overcome the problem of the short retention time of CPC and could be used for buccal delivery as a topical anti-infective agent. Methods: CPC bioadhesive tablets were directly prepared using 7 mm flat-faced punches on a hydraulic press. The materials for each tablet were weighted, introduced into the die and compacted at constant compression pressure. The dissolution tests were performed to the rotation paddle method and the bioadhesive strength of the tablets were measured. Results: The results showed that as the concentration of polymer increased, the drug release rate was decreased. Also the type and ratio of polymers altered the release kinetic of Cetylpyridinium Chloride from investigated tablets. The bioadhesion strength increased with increasing the concentration of polymer and maximum bioadhesion strength was observed with HPMC K100M. Conclusion: The selected formulation of CPC bioadhesive tablet can be used as a suitable preparation for continuous release of CPC with appropriate bioadhesion strength. PMID:25436196

  7. Modeling Fate and Transport of Chloride from Deicers in Urban Floodplains: Implications for Urban Planning

    Science.gov (United States)

    Ledford, S. H.; Lautz, L.

    2015-12-01

    Road salting in urban areas of the northeastern United States increases chloride concentrations in urban streams. Groundwater storage of saline road runoff results in increased surface water chloride concentrations through time, even in non-winter months. Stream-groundwater (SW-GW) interactions promote buffering of large seasonal swings in stream chloride concentrations, resulting in lower surface water chloride in winter and higher concentrations in summer, relative to streams hydrologically disconnected from riparian floodplains. However, the hydrogeologic processes controlling salt storage and transport in urban floodplain aquifers have not been fully investigated. We developed a 3D numerical groundwater flow and solute transport model of an urban floodplain in Syracuse, New York, using MODFLOW and MT3DMS. We ran the model for 1 year, calibrating to three conditions: water table elevations along a riparian transect, measurements of net groundwater flux to the stream along the 500-m reach, and chloride concentrations in groundwater through time in riparian wells. Chloride enters the riparian aquifer via three pathways: hillslope groundwater discharge, hyporheic exchange, and groundwater recharge during overbank flooding events. Winter overbank flooding events are the primary source of chloride to floodplain sediments. While hillslope groundwater discharge results in relatively uniform chloride through time in high conductivity units, surficial floodplain sediments with lower conductivity have high chloride concentrations from winter overbank flood events. When compared to road salt application rates (up to 20 tons of salt per lane kilometer per year), the 0.013 km2 floodplain holds only a tiny fraction of chloride applied in a watershed (>100 km of road in the watershed). To promote riparian aquifer storage of road salt and buffering of stream chloride concentrations, urban planners should design urban floodplains for frequent winter flooding events, and allow

  8. Dynamic [Cl-]i measurement with chloride sensing quantum dots nanosensor in epithelial cells

    Science.gov (United States)

    Wang, Yuchi; Mao, Hua; Wong, Lid B.

    2010-02-01

    We have synthesized a chloride sensing quantum dots (QD) nanosensor, Cl-QD, for the dynamic measurements of chloride ion concentration in the millimolar range, a sensitivity that is applicable to most physiological intracellular chloride ion concentration ([Cl-]i) measurements in epithelial cells. The Cl-QD is synthesized by conjugating an anion receptor, 1-(2-mercapto-ethyl)-3-phenyl-thiourea (MEPTU) to a water soluble CdSe/ZnS QD at an emission wavelength of 620 nm. Upon binding of chloride ions to the Cl-QD, a photo-induced electron transfer mechanism caused the fluorescence of the QD to quench. This resulted in an inversely proportional relationship between the chloride ion concentration and the fluorescence intensity of the Cl-QD. We have utilized this Cl-QD to measure [Cl-]i in T84 and CF-PAC cultured cells, with either the C1C-2 or CFTR chloride channels being manipulated by pharmacological chloride channel activators and inhibitors. Activations of C1C-2 and CFTR chloride channels in T84 by the respective lubiprostone and genistein caused predictive increases in the fluorescence of the Cl-QD, i.e., a decrease of [Cl-]i. Conversely, glibenclamide, a chloride channel inhibitor, applied to the CF-PAC cells caused a predictable decrease in the fluorescence of Cl-QD due to the increase of [Cl-]i. These are the first data in using QD-based chloride ion sensors for dynamic measurements of intracellular chloride ion concentrations in epithelial cells.

  9. Chloride content and pH value in the pore solution of concrete under carbonation

    Institute of Scientific and Technical Information of China (English)

    Xiao-mei WAN; Folker H.WITTMANN; Tie-jun ZHAO; Hong FAN

    2013-01-01

    Chloride content and the pH value of the pore solution in the neighborhood of steel reinforcement are decisive parameters for initiation and rate of corrosion.The pore solution of cement mortar and hardened cement paste has been expressed from the pore space by high pressure in the investigation.The influence of the water-cement ratio,age,and addition of chloride to the fresh mix on chloride content in the pore solution has been determined by ion chromatography.At the same time the pH value of the pore solution has been determined.The dissolved chloride content decreases with increase in the water-cement ratio.The amount of bound chloride increases with time,but it decreases with decreasing content of dissolved chloride in the pore solution.A significant influence of carbonation on the dissolved chloride content of the pore solution has been observed.With complete carbonation,the dissolved chloride content in cement mortar and hardened cement paste increases by a factor between 2 and 12.The bound chloride decreases by 27%-54%.As expected,the pH value decreases from around 13.2 to as low as 8.0 due to carbonation.It can be concluded that carbonation not only lowers the pH value but liberates bound chloride.This is one obvious reason why the combined action of chloride penetration and carbonation accelerates steel corrosion and shortens the service life of reinforced concrete structures.

  10. Dynamic [Cl{sup -}]{sub i} measurement with chloride sensing quantum dots nanosensor in epithelial cells

    Energy Technology Data Exchange (ETDEWEB)

    Wang Yuchi; Mao Hua; Wong, Lid B, E-mail: ywang@biotechplex.com [BioTechPlex Corporation, 1205 Linda Vista Drive Suite A, San Marcos, CA 92078 (United States); Cytoptics Corporation, 1205 Linda Vista Drive Suite B, San Marcos, CA 92078 (United States)

    2010-02-05

    We have synthesized a chloride sensing quantum dots (QD) nanosensor, Cl-QD, for the dynamic measurements of chloride ion concentration in the millimolar range, a sensitivity that is applicable to most physiological intracellular chloride ion concentration ([Cl{sup -}]{sub i}) measurements in epithelial cells. The Cl-QD is synthesized by conjugating an anion receptor, 1-(2-mercapto-ethyl)-3-phenyl-thiourea (MEPTU) to a water soluble CdSe/ZnS QD at an emission wavelength of 620 nm. Upon binding of chloride ions to the Cl-QD, a photo-induced electron transfer mechanism caused the fluorescence of the QD to quench. This resulted in an inversely proportional relationship between the chloride ion concentration and the fluorescence intensity of the Cl-QD. We have utilized this Cl-QD to measure [Cl{sup -}]{sub i} in T84 and CF-PAC cultured cells, with either the C1C-2 or CFTR chloride channels being manipulated by pharmacological chloride channel activators and inhibitors. Activations of C1C-2 and CFTR chloride channels in T84 by the respective lubiprostone and genistein caused predictive increases in the fluorescence of the Cl-QD, i.e., a decrease of [Cl{sup -}]{sub i}. Conversely, glibenclamide, a chloride channel inhibitor, applied to the CF-PAC cells caused a predictable decrease in the fluorescence of Cl-QD due to the increase of [Cl{sup -}]{sub i}. These are the first data in using QD-based chloride ion sensors for dynamic measurements of intracellular chloride ion concentrations in epithelial cells.

  11. Floc properties and membrane fouling of polyferric silicate chloride and polyferric chloride: the role of polysilicic acid.

    Science.gov (United States)

    Dong, Hongyu; Gao, Baoyu; Yue, Qinyan; Sun, Shenglei; Wang, Yan; Li, Qian

    2015-03-01

    Impact of polysilicic acid (pSi) in polyferric silicate chloride (PFSiC) on coagulation-ultrafiltration process was investigated in comparison with polyferric chloride (PFC). The Fe(III) species distribution in PFSiC and PFC was measured by a timed complexation spectroscopy method. Characteristics of flocs produced by PFSiC and PFC were studied using a laser diffraction particle sizing device. Moreover, membrane fouling was evaluated using a dead-end batch ultrafiltration unit under two operation modes, coagulation-ultrafiltration (C-UF) and coagulation-sedimentation-ultrafiltration (CSUF). The results indicated that PFSiC with various Si/Fe ratios had better turbidity removal efficiency but inferior organic matter removal. Flocs formed by PFSiC were larger than those by PFC. In case of PFSiC, floc size increased with Si/Fe ratio increasing. PFSiC with various Si/Fe ratios resulted in more compact and weaker flocs than PFC. Ultrafiltration experiments indicated that under C-UF mode, PFSiC with Si/Fe ratios of 0.07 and 0.10 presented better membrane performance than PFC. Under CSUF mode, addition of pSi could alleviate membrane fouling.

  12. Technical Note: Could benzalkonium chloride be a suitable alternative to mercuric chloride for preservation of seawater samples?

    Directory of Open Access Journals (Sweden)

    J. Gloël

    2015-08-01

    Full Text Available Instrumental equipment unsuitable or unavailable for fieldwork as well as lack of ship space can necessitate the preservation of seawater samples prior to analysis in a shore-based laboratory. Mercuric chloride (HgCl2 is routinely used for such preservation, but its handling and subsequent disposal incur significant risks and expense. Benzalkonium chloride (BAC has been used previously for freshwater samples. Here, we assess BAC as a less hazardous alternative microbial inhibitor for marine samples prior to the measurement of oxygen-to-argon (O2/Ar ratios, as used for the determination of plankton net community production. BAC at a concentration of 50 mg dm−3 inhibited microbial activity for at least three days in seawater with chlorophyll a (Chl a concentrations up to 1 mg m−3, possibly longer when Chl a concentrations were lower. BAC concentrations of 100 and 200 mg dm−3 were no more effective than 50 mg dm−3. With fewer risks to human health and the environment, and no requirement for expensive waste disposal, BAC could be a viable alternative to HgCl2 for short-term preservation of seawater samples, but is not a replacement for HgCl2 in the case of oxygen triple isotope analysis, which requires storage over weeks to months. In any event, further tests on a case-by-case basis should be undertaken if use of BAC was considered, since its inhibitory activity may depend on concentration and composition of the microbial community.

  13. Technical note: Could benzalkonium chloride be a suitable alternative to mercuric chloride for preservation of seawater samples?

    Science.gov (United States)

    Gloël, J.; Robinson, C.; Tilstone, G. H.; Tarran, G.; Kaiser, J.

    2015-12-01

    Instrumental equipment unsuitable or unavailable for fieldwork as well as lack of ship space can necessitate the preservation of seawater samples prior to analysis in a shore-based laboratory. Mercuric chloride (HgCl2) is routinely used for such preservation, but its handling and subsequent disposal incur environmental risks and significant expense. There is therefore a strong motivation to find less hazardous alternatives. Benzalkonium chloride (BAC) has been used previously as microbial inhibitor for freshwater samples. Here, we assess the use of BAC for marine samples prior to the measurement of oxygen-to-argon (O2 / Ar) ratios, as used for the determination of biological net community production. BAC at a concentration of 50 mg dm-3 inhibited microbial activity for at least 3 days in samples tested with chlorophyll a (Chl a) concentrations up to 1 mg m-3. BAC concentrations of 100 and 200 mg dm-3 were no more effective than 50 mg dm-3. With fewer risks to human health and the environment, and no requirement for expensive waste disposal, BAC could be a viable alternative to HgCl2 for short-term preservation of seawater samples, but is not a replacement for HgCl2 in the case of oxygen triple isotope analysis, which requires storage over weeks to months. In any event, further tests on a case-by-case basis should be undertaken if use of BAC was considered, since its inhibitory activity may depend on concentration and composition of the microbial community.

  14. Effet of Mercuric Chloride and Cadmium Chloride on Gonadal Function and Its regulation in Sexually Mature Common Carp Cyprinus carpio

    Institute of Scientific and Technical Information of China (English)

    DilipMUKHERJEE; VinodKumar; 等

    1994-01-01

    Gnadal function in fish,Cyprinus carpio was significantly affected by sublethal doses of mecuric chloride(HgCl2)and cadmium chloride(CdCl2)in chronic(45days)exposure,Parameters investigated were nonesterified(NE)and esterified(E)cholesterol of ovary, liver and serum and ovarian 3β-Hydroxysteroid and 17β-Hydroxysteroid dehydrogenase enzyme activity and servum and pituitary gonadotropin(GtH)levels.Both the pollutats were able to reduce the hypothalamic extract(HE)or gonadotropin releasing hormone (GnRH)induced pituiteray GtH release in vitro.Short term(96h)exposure of the fish to the polltants had no significant effect on the gonadal founction.In addition to the deleterious effect of pollutants on the gonadal steroidogenesis and pituitary gonadotropin release,using [4-14C] cholesterol as a tracer it was found that for 45 days exposure,HgCl2 had an adverse effect on the transport of cholesterol from circulation to ovary.

  15. Effects of antigliomatin from the scorpion venom of Buthus martensii Karsch on chloride channels on C6 glioma cells

    Institute of Scientific and Technical Information of China (English)

    Zan Wang; Mingxian Li; Hongmei Meng; Min Huang; Weihong Lin; Li Cui; Shao Wang

    2011-01-01

    Using whole-cell patch-clamp recordings, the effects of antigliomatin were observed on chloride channels on C6 glioma cells cultured in vitro. Antigliomatin was extracted from the venom of the scorpion Buthus martensii Karsch. Chloride channels are closed under normal osmotic pressure. When osmotic pressure was reduced to 120, 110 and 100 mV, the cell volume enlarged, chloride channels opened, and the chloride channel current increased. Three minutes after antigliomatin treatment, the chloride channel current decreased in a dose-dependent manner. These results show that antigliomatin extracted from the venom of the scorpion Buthus martensii Karsch diminishes chloride channel currents on C6 glioma cells.

  16. Correlation of the rates of solvolysis of two arenesulfonyl chlorides and of trans-beta-styrenesulfonyl chloride - precursors in the development of new pharmaceuticals.

    Science.gov (United States)

    Ryu, Zoon H; Lee, Sang W; D'Souza, Malcolm J; Yaakoubd, Lamia; Feld, Samantha E; Kevill, Dennis N

    2008-12-01

    Additional specific rates of solvolysis have been determined, mainly in fluoroalcohol containing solvents, for benzenesulfonyl chloride (1) and p-nitrobenzene-sulfonyl chloride (2). For trans-beta-styrenesulfonyl chloride (3), a study has been carried out in 43 pure and binary solvents, covering a wide range of hyroxylic solvent systems. For the specific rates of solvolyses of each of the three substrates, a good correlation was obtained over the full range of solvents when the extended Grunwald-Winstein equation was applied. The sensitivities to changes in solvent nucleophilicity and solvent ionizing power are similar to values determined earlier and an S(N)2 process is proposed. For 3, kinetic solvent isotope effects of 1.46 for k(H(2)O)/k(D(2)O) and 1.76 for k(MeOH)/k(MeOD) were determined. These are also compared to literature values for other sulfonyl chlorides.

  17. Paired observation of californium-252 neutron intraluminal brachytherapy combined with external-beam radiotherapy with and without lead shielding for cervical cancer%252 Cf中子腔内照射结合挡铅与不挡铅外照射治疗宫颈癌的配对观察

    Institute of Scientific and Technical Information of China (English)

    戴卓捷; 雷新; 陈永红; 刘佳

    2015-01-01

    目的:比较252 Cf中子腔内照射结合挡铅盆腔对穿野和不挡铅箱式四野外照射治疗宫颈癌的治疗结果。方法2004—2007年本院收治的Ⅱa—Ⅲb 期的宫颈鳞癌患者,按照临床分期、年龄、肿瘤大小、贫血程度为配对条件,共筛选出26对(52例)研究对象,分为挡铅盆腔对穿野组(挡铅组)和不挡铅箱式四野组(不挡铅组)。两组患者外照射期间穿插252 Cf中子后装治疗。 Kaplan?Meier法计算5年LC、OS、DFS 并 Logrank 检验差异,晚期并发症发生率差异行 McNemar 法检验。结果挡铅、不挡铅组5年LC 率分别为85%、81%(P=0??014),OS 率分别为89%、73%(P=0??013),DFS 率分别为89%、73%(P=0??013),晚期并发症发生率分别为12%、23%(P=0??008)。结论腔内照射结合外照射治疗宫颈癌时无论采取对穿野还是箱式四野,后程前后野中央均应挡铅。%Objective To compare the efficacy between californium?252 ( 252 Cf ) neutron intraluminal brachytherapy combined with external?beam radiotherapy with lead?shielding pelvic parallel opposing field technique and non?lead?shielding four?field box technique for cervical cancer. Methods A total of 52 patients with stage Ⅱa?Ⅲb cervical squamous cell carcinoma who were admitted to our hospital from 2004 to 2007 were enrolled as subjects and paired by clinical stage, age, tumor size, and degree of anemia. The 26 pairs of patients were divided into lead?shielding pelvic parallel opposing field group (lead?shielding group) and non?lead?shielding four?field box group (non?lead?shielding group). For all patients in both groups, 252 Cf neutron brachytherapy was added in external?beam radiotherapy. The local control (LC), overall survival (OS), and disease?free survival (DFS) rates were calculated using the Kaplan?Meier method and analyzed using the log?rank test. The difference in the incidence of late complications was

  18. Roles of Novel Reactive Cationic Copolymers of 3-Chloro-2-hydroxypropylmethyldiallylammonium Chloride and Dimethyldiallylammonium Chloride in Fixing Anionic Dyes on Cotton Fabric

    OpenAIRE

    2013-01-01

    The roles of novel reactive cationic copolymers (P(CMDA-DMDAAC)s) of 3-chloro-2-hydroxypropylmethyldiallylammonium chloride (CMDA) and dimethyldiallylammonium chloride (DMDAAC) in fixing anionic dyes on cotton fabric were studied by modern instrumental analysis technologies such as FT-IR spectra and SEM analysis, to achieve the new theoretical guides for the wide applications of those dye fixatives. The FT-IR spectra of the obtained insoluble-water color lakes verified that they could be form...

  19. The Role of Chloride Ions during the Formation of Akaganéite Revisited

    Directory of Open Access Journals (Sweden)

    Johanna Scheck

    2015-11-01

    Full Text Available Iron(III hydrolysis in the presence of chloride ions yields akaganéite, an iron oxyhydroxide mineral with a tunnel structure stabilized by the inclusion of chloride. Yet, the interactions of this anion with the iron oxyhydroxide precursors occurring during the hydrolysis process, as well as its mechanistic role during the formation of a solid phase are debated. Using a potentiometric titration assay in combination with a chloride ion-selective electrode, we have monitored the binding of chloride ions to nascent iron oxyhydroxides. Our results are consistent with earlier studies reporting that chloride ions bind to early occurring iron complexes. In addition, the data suggests that they are displaced with the onset of oxolation. Chloride ions in the akaganéite structure must be considered as remnants from the early stages of precipitation, as they do not influence the basic mechanism, or the kinetics of the hydrolysis reactions. The structure-directing role of chloride is based upon the early stages of the reaction. The presence of chloride in the tunnel-structure of akagenéite is due to a relatively strong binding to the earliest iron oxyhydroxide precursors, whereas it plays a rather passive role during the later stages of precipitation.

  20. 21 CFR 700.19 - Use of methylene chloride as an ingredient of cosmetic products.

    Science.gov (United States)

    2010-04-01

    ... cosmetic products. 700.19 Section 700.19 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) COSMETICS GENERAL Requirements for Specific Cosmetic Products § 700.19 Use of methylene chloride as an ingredient of cosmetic products. (a) Methylene chloride has been...

  1. Oxidative addition of aryl chlorides to monoligated palladium(0): A DFT-SCRF study

    DEFF Research Database (Denmark)

    Ahlquist, Mårten Sten Gösta; Norrby, Per-Ola

    2007-01-01

    Oxidative addition of aryl chlorides to palladium has been investigated by hybrid density functional theory methods (B3LYP), including a continuum model describing the solvent implicitly. A series of para-substituted aryl chlorides were studied to see the influence of electronic effects on the re...

  2. 21 CFR 175.360 - Vinylidene chloride copolymer coatings for nylon film.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Vinylidene chloride copolymer coatings for nylon... coatings for nylon film. Vinylidene chloride copolymer coatings identified in this section and applied on nylon film may be safely used as food-contact surfaces, in accordance with the following...

  3. 21 CFR 177.2000 - Vinylidene chloride/methyl acrylate/methyl methacrylate polymers.

    Science.gov (United States)

    2010-04-01

    ... methacrylate polymers. 177.2000 Section 177.2000 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF...: POLYMERS Substances for Use as Basic Components of Single and Repeated Use Food Contact Surfaces § 177.2000 Vinylidene chloride/methyl acrylate/methyl methacrylate polymers. The vinylidene chloride/methyl...

  4. Synthesis of phosphorus-containing polyoxamacrocycles with one to two reactive thiophosphoryl chloride groups

    Institute of Scientific and Technical Information of China (English)

    Xiao Mei Zhang; Dao Quan Wang; Wan Yi Chen

    2008-01-01

    Novel phosphorus-containing polyoxamacrocycles with one to two reactive thiophosphoryl chloride groups 5, 6, 7, 8 weresynthesized from bishydroxyl compounds 1, 2, 3, 4 and thiophosphoryl chloride respectively. Their structures were confirmed by 1HNMR, 13C NMR, 31p NMR and elemental analysis.2008 Dan Quan Wang. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.

  5. Scientific Basis for Paint Stripping: Elucidated Combinatorial Mechanism of Methylene Chloride and Phenol Based Paint Removers

    Science.gov (United States)

    2013-10-10

    Electron Microscope SERDP - Strategic Environmental Research and Development Program Tg – Glass Transition TGA – Thermal Gravimetric Analysis UV... analysis , visible microscopy and spectroscopy and vibrational spectroscopy to understand the mechanism of how methylene chloride based paint removers...allowed for analysis of the different components of methylene chloride based paint strippers. Methocel is the trade name of hydroxypropyl

  6. Recurrent studies of chloride ingress in uncracked marine concrete at various exposure times and elevations

    Energy Technology Data Exchange (ETDEWEB)

    Sandburg, P. [Lund Inst. of Tech. (Sweden). Div. of Building Materials; Tang, L. [Swedish National Testing and Research Inst., Boraes (Sweden); Andersen, A. [Chalmers Univ., Goeteborg (Sweden). Div. of Building Materials

    1998-10-01

    Uncracked reinforced concrete slabs were field exposed mounted on a floating pontoon and partly submerged for 5 years at the Swedish west coast. The total chloride ingress was analyzed at various exposure times at 3 elevations representing a submerged, a splash, and an atmospheric exposure zone. The concrete mixtures varied in w/c ratio, type of cement, and amount and type of pozzolan used in the binder. The data is unique as it represents recurrently measured total chloride penetration profiles at various exposure ages, providing a foundation for the prediction of chloride ingress in concrete in a given environment. The results after 5 years of exposure confirmed the expected inverse relationship between water-to-binder ratio and chloride ingress. The use of 5--10% silica fume in the binder had a very positive effect on reducing the chloride ingress, but little or no benefit at all was found for concrete with fly ash in the binder as compared to the use of 5% silica fume. The chloride penetration rate as expressed by a calculated effective chloride diffusivity has a tendency to decrease over time. High-performance concrete with w/c {le} 0.4 and a minimum of 5% silica fume added as a well dispersed slurry exhibited an effective chloride diffusivity in the range of 1 {times} 10{sup {minus}13} to 5 {times} 10{sup {minus}13} m{sup 2}/s after 5 years exposure in the splash zone.

  7. Experimental and modeling study of chloride ingress into concrete and reinforcement corrosion initiation

    Science.gov (United States)

    Yu, Hui

    Effects of reinforcement and coarse aggregate on chloride ingression into concrete and reinforcement corrosion initiation have been studied with experimental and modeling (finite element method) analyses. Once specimens were fabricated and exposed to a chloride solution, various experimental techniques were employed to determine the effect of reinforcement and coarse aggregate on time-to-corrosion and chloride ingress and concentration at corrosion locations. Model analyses were performed to verify and explain the experimental results. Based upon the results, it was determined that unexpectedly higher chloride concentrations were present on the top of the rebar trace than that to the side at the same depth and an inverse concentration gradient (increasing [ Cl-] with increasing depth) occurred near the top of rebars. Also, coarse aggregate volume profile in close proximity to the rebar and spatial distribution of these aggregates, in conjunction with the physical obstruction afforded by reinforcement to chloride flow, complicates concrete sampling for Cl- intended to define the critical concentration of this species to initiate corrosion. Modeling analyses that considered cover thickness, chloride threshold concentration, reinforcement size and shape, and coarse aggregate type and percolation confirmed the experimental findings. The results, at least in part, account for the relatively wide spread in chloride corrosion threshold values reported in the literature and illustrate that more consistent chloride threshold concentrations can be acquired from mortar or paste specimens than from concrete ones.

  8. Mechanism of sodium chloride in promoting reduction of high-magnesium low-nickel oxide ore.

    Science.gov (United States)

    Zhou, Shiwei; Wei, Yonggang; Li, Bo; Wang, Hua; Ma, Baozhong; Wang, Chengyan

    2016-07-04

    Sodium chloride has been proved that it is an effective promoter for the reduction of high-magnesium, low-nickel oxide ore. The aim of current work is to clarify the promotion behavior of sodium chloride in the roasting reduction process. The influence of moisture on the reduction of ore in the presence of sodium chloride is studied to get clear comprehension of promotion process. In the presence of moisture, the HCl is produced by pyrohydrolysis of sodium chloride for chlorinating nickel and iron oxides, moreover, interactions between metallic oxides and sodium chloride are also a way for chlorination at high temperature (>802 °C); subsequently, the metal chloride would be reduced by reductant. In the absence of moisture, the magnetic separation results show that the recoveries of iron and nickel have a significant increase; moreover, olivine structure would be destroyed gradually with the increase of roasting temperature in the action of sodium chloride, and the sodium chloride existed in high-magnesium, low-nickel oxide ore could make the NiO isolate from NiO-bearing minerals. The NiO reacts with Fe2O3 at high temperature to form NiFe2O4, which is conductive to the formation of Ni-Fe alloy during the reduction process.

  9. Chloride Ion Transport in Fly Ash Mortar under Action of Fatigue Loading

    Institute of Scientific and Technical Information of China (English)

    WANG Caihui; SUN Wei; JIANG Jinyang

    2012-01-01

    In order to study the chloride ion transport performance in fly ash addition mortar,a new method,in which the fatigue loading and chloride diffusion are undertaken simultaneously,was developed.This method realizes coupling the fatigue damage process and the process of chloride transporting of fly ash mortar.The transport performance of chloride in fly ash mortar specimens was studied under different stress levels.Moreover,the effect of fly ash content on transport performance of chloride ion in mortar was investigated.AE (Acoustic Emission) and SEM were used to acquire the damage distribution of mortar specimens under action of fatigue load.The results show that the diffusion coefficient of chloride in mortar specimens increases with stress level of fatigue loading.The addition of fly ash can mitigate the penetration of chloride ion.The results of microcrack 3D location acquired by AE,accompanied with crack characterizing from SEM,indicate that the damage degree of mortar specimen increases with stress level of fatigue loading.Furthermore,higher damage degree of mortar leads to more the chloride ion content in the sample.

  10. A novel capsule-based selfrecovery system with a chloride ion trigger

    NARCIS (Netherlands)

    Xiong, W.; Tang, J.; Zhu, G.; Han, N.; Schlangen, E.; Dong, B.; Wang, X.; Xing, F.

    2015-01-01

    Steel is prone to corrosion induced by chloride ions, which is a serious threat to reinforced concrete structures, especially in marine environments. In this work, we report a novel capsule-based selfrecovery system that utilizes chloride ions as a trigger. These capsules, which are functionalized v

  11. Electrochemical activity of heavy metal oxides in the process of chloride induced corrosion of steel reinforcement

    Indian Academy of Sciences (India)

    V Živica

    2002-10-01

    The influence of heavy metal oxides on the chloride induced corrosion of steel reinforcement in concrete was studied. Significant inhibition and stimulation of chloride induced corrosion have been observed. Basicity and acidity of the relevant metal ions, and their ability to form complexes are considered as the main factors of the observed effects.

  12. Dietary Impact of Adding Potassium Chloride to Foods as a Sodium Reduction Technique

    Directory of Open Access Journals (Sweden)

    Leo van Buren

    2016-04-01

    Full Text Available Potassium chloride is a leading reformulation technology for reducing sodium in food products. As, globally, sodium intake exceeds guidelines, this technology is beneficial; however, its potential impact on potassium intake is unknown. Therefore, a modeling study was conducted using Dutch National Food Survey data to examine the dietary impact of reformulation (n = 2106. Product-specific sodium criteria, to enable a maximum daily sodium chloride intake of 5 grams/day, were applied to all foods consumed in the survey. The impact of replacing 20%, 50% and 100% of sodium chloride from each product with potassium chloride was modeled. At baseline median, potassium intake was 3334 mg/day. An increase in the median intake of potassium of 453 mg/day was seen when a 20% replacement was applied, 674 mg/day with a 50% replacement scenario and 733 mg/day with a 100% replacement scenario. Reformulation had the largest impact on: bread, processed fruit and vegetables, snacks and processed meat. Replacement of sodium chloride by potassium chloride, particularly in key contributing product groups, would result in better compliance to potassium intake guidelines (3510 mg/day. Moreover, it could be considered safe for the general adult population, as intake remains compliant with EFSA guidelines. Based on current modeling potassium chloride presents as a valuable, safe replacer for sodium chloride in food products.

  13. The influence of polyvinyl chloride (P.V.C.) tubing on the isolated perfused rat heart

    NARCIS (Netherlands)

    Meijler, F.L.; Willebrands, A.F.; Durrer, D.

    1960-01-01

    Some brands of polyvinyl chlorides interfere with cardiac contraction, whereas other brands do not. Chemical investigation showed that the stabilizer is most probably responsibie for the cardiotoxic effect. It is suggested that all types of polyvinyl chloride used for medical and biological applica

  14. De invloed van plastic (polyvinyl-chloride) op het geïsoleerde overlevende rattehart

    NARCIS (Netherlands)

    Meijler, F.L.; Willebrands, A.F.; Durrer, D.

    1959-01-01

    Sommige soorten plastic(polyvinyl-chloride)slang doen de mechanische activiteit van het overlevende, geïsoleerde rattehart verminderen, of verdwijnen. Dit polyvinyl-chloride wordt verkocht en gebruikt voor medische en biologische doeleinden. Chemische analyses toonden een duidelijk verschil tussen d

  15. Alkali chloride induced corrosion of superheaters under biomass firing conditions: Improved insights from laboratory scale studies

    DEFF Research Database (Denmark)

    Okoro, Sunday Chukwudi; Montgomery, Melanie; Jappe Frandsen, Flemming

    2015-01-01

    to the formation of corrosive deposits (rich in alkali chlorides) on the surfaces of the superheaters. Accordingly, an extensive number of fundamental investigations have been undertaken to understand the basic mechanisms behind the alkali chloride induced high temperature corrosion of superheaters (for example...

  16. Catalytic allylation of phenols : chloride-free route towards epoxy resins

    NARCIS (Netherlands)

    Rijn, Jimmy Antonius van

    2010-01-01

    An industrially applicable process was developed for the synthesis of epoxy resin components. A catalytic reaction was explored towards allyl phenyl ethers that prevents the use of chloride-containing starting materials and thus formation of chloride-containing side products. The preferred allylatin

  17. SUBACUTE HEMATOLOGICAL RESPONSES OF THE YUCATAN SAILFIN MOLLY (POECILIA VELIFERA) EXPOSED TO CADMIUM CHLORIDE

    Science.gov (United States)

    This study focuses on the subacute hematological responses of the Yucatan sailfin molly, Poecilia velifera, exposed to cadmium chloride. Previous studies in other teleosts and mammals have suggested that exposure to cadmium chloride results in a leucocytic response. Fish were exp...

  18. SUBACTUTE HEMATOLOGICAL RESPONSES OF THE YUCATAN SAILFIN MOLLY (POECILIA VELIFERA) EXPOSED TO CADMIUM CHLORIDE

    Science.gov (United States)

    This study focuses on the subacute hematological responses of the Yucatan sailfin molly, Poecilia velifera, exposed to cadmium chloride. Previous studies in other teleosts and mammals have suggested that exposure to cadmium chloride results in a leucocytic response. Fish were exp...

  19. Bifunctional Asymmetric Catalysis with Hydrogen Chloride: Enantioselective Ring-Opening of Aziridines Catalyzed by a Phosphinothiourea.

    Science.gov (United States)

    Mita, Tsuyoshi; Jacobsen, Eric N

    2009-06-01

    Ring-opening of aziridines with hydrogen chloride to form β-chloroamine derivatives is catalyzed by a chiral phosphinothiourea derivative in high yields and with high enantioselectivities. On the basis of (31)P NMR studies, activation of HCl appears to proceed via quantitative protonation of the catalyst to afford a phosphonium chloride complex.

  20. Resistance of Alkali-Activated Slag Concrete to Chloride-Induced Corrosion

    Directory of Open Access Journals (Sweden)

    Joon Woo Park

    2015-01-01

    Full Text Available The corrosion resistance of steel in alkali-activated slag (AAS mortar was evaluated by a monitoring of the galvanic current and half-cell potential with time against a chloride-contaminated environment. For chloride transport, rapid chloride penetration test was performed, and chloride binding capacity of AAS was evaluated at a given chloride. The mortar/paste specimens were manufactured with ground granulated blast-furnace slag, instead of Portland cement, and alkali activators were added in mixing water, including Ca(OH2, KOH and NaOH, to activate hydration process. As a result, it was found that the corrosion behavior was strongly dependent on the type of alkali activator: the AAS containing the Ca(OH2 activator was the most passive in monitoring of the galvanic corrosion and half-cell potential, while KOH, and NaOH activators indicated a similar level of corrosion to Portland cement mortar (control. Despite a lower binding of chloride ions in the paste, the AAS had quite a higher resistance to chloride transport in rapid chloride penetration, presumably due to the lower level of capillary pores, which was ensured by the pore distribution of AAS mortar in mercury intrusion porosimetry.

  1. Interim Report on Scientific Basis for Paint Stripping: Mechanism of Methylene Chloride Based Paint Removers

    Science.gov (United States)

    2010-10-18

    free unreacted functional groups. After observing satisfactory results, TGA analysis was performed to ensure the absence of nontraditional species...methylene chloride, EtOH, water and PhOH decomposed into small pieces, like MIL-85285, preventing DSC and TGA analysis . Exposure to methylene chloride and

  2. 21 CFR 175.365 - Vinylidene chloride copolymer coatings for polycarbonate film.

    Science.gov (United States)

    2010-04-01

    ... polycarbonate film. 175.365 Section 175.365 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH... chloride copolymer coatings for polycarbonate film. Vinylidene chloride copolymer coatings identified in this section and applied on polycarbonate film may be safely used as food-contact surfaces,...

  3. High-rate lithium thionyl-chloride battery development

    Energy Technology Data Exchange (ETDEWEB)

    Cieslak, W.R.; Weigand, D.E.

    1993-12-31

    We have developed a lithium thionyl-chloride cell for use in a high rate battery application to provide power for a missile computer and stage separation detonators. The battery pack contains 20 high surface area ``DD`` cells wired in a series-parallel configuration to supply a nominal 28 volts with a continuous draw of 20 amperes. The load profile also requires six squib firing pulses of one second duration at a 20 ampere peak. Performance and safety of the cells were optimized in a ``D`` cell configuration before progressing to the longer ``DD` cell. Active surface area in the ``D`` cell is 735 cm{sup 2}, and 1650 cm{sup 2} in the ``DD`` cell. The design includes 1.5M LiAlCl{sub 4}/SOCl{sub 2} electrolyte, a cathode blend of Shawinigan Acetylene Black and Cabot Black Pearls 2000 carbons, Scimat ETFE separator, and photoetched current collectors.

  4. Self-discharge rate of lithium thionyl-chloride cells

    Energy Technology Data Exchange (ETDEWEB)

    Cieslak, W.R.

    1993-12-31

    Our low-rate lithium/thionyl-chloride ``D`` cell is required to provide power continuously for up to 10 years. The cell was designed at Sandia National Laboratories and manufactured at Eagle-Picher Industries, Joplin, Missouri. We have conducted accelerated aging studies at elevated temperatures to predict long-term performance of cells fabricated in 1992. Cells using 1.0M LiAlCl{sub 4} electrolyte follow Arrhenius kinetics with an activation energy of 14.6 Kcal/mol. This results in an annual capacity loss to self-discharge of 0.13 Ah at 25 C. Cells using a 1.0M LiAlCl{sub 4}{sm_bullet}SO{sub 2} electrolyte do not follow Arrhenius behavior. The performance of aged cells from an earlier fabrication lot is variable.

  5. Space-charge at the lithium-lithium chloride interface

    Science.gov (United States)

    Jamnik, J.; Gaberscek, M.; Meden, A.; Pejovnik, S.

    1991-06-01

    The electrical properties of the passive layer formed on lithium as the product of the corrosion reaction in thionyl chloride are discussed. The passive layer is regarded as a thin layer of an ionic crystal placed between two party blocking electrodes (i.e., lithium and liquid electrolyte). After a short review of thermodynamic properties of the system, a model for description of the electric properties of the static space-charge regions is presented. On this basis, a comment on and partial reinterpretation of impedance measurements of the passive layer is given. The suggested approach leads to the conclusion that the quality of Li/SOCl2 batteries decisively depends on the properties of the lithium passive layer interface. Finally, experiments to confirm the model are suggested.

  6. Lithium-thionyl chloride cell system safety hazard analysis

    Science.gov (United States)

    Dampier, F. W.

    1985-03-01

    This system safety analysis for the lithium thionyl chloride cell is a critical review of the technical literature pertaining to cell safety and draws conclusions and makes recommendations based on this data. The thermodynamics and kinetics of the electrochemical reactions occurring during discharge are discussed with particular attention given to unstable SOCl2 reduction intermediates. Potentially hazardous reactions between the various cell components and discharge products or impurities that could occur during electrical or thermal abuse are described and the most hazardous conditions and reactions identified. Design factors influencing the safety of Li/SOCl2 cells, shipping and disposal methods and the toxicity of Li/SOCl2 battery components are additional safety issues that are also addressed.

  7. Capacity loss and faradaic efficiency of lithium thionyl chloride cells

    Energy Technology Data Exchange (ETDEWEB)

    Hoier, S. [Sandia National Labs., Albuquerque, NM (United States); Schlaikjer, C.; Johnson, A.; Riley, S. [Battery Engineering, Inc., Boston, MA (United States)

    1996-05-01

    In lithium/thionyl chloride (Li/TC) cells, a lithium limited design was thought to be safer than a cathode limited design because the amount of lithium left in discharged cells would be minimal. However, lithium corrosion reduces the capacity faster than does cathode degradation during storage. The optimization of the ratio of lithium to carbon was studied, considering storage time and temperature. The efficiency of converting chemical energy into electrical energy has been studied for the case of D cells with surface area from 45 to 345 cm{sup 2}, under constant and various pulsed loads. Microcalorimetric monitoring of the heat output during discharge allowed the direct measurement of faradaic efficiency, and showed that self discharge is far more pervasive that previously acknowledged. Typical faradaic efficiencies for constant load varied from 30% at low current density to 90% at moderate and 75 % at high current density. Pulsed current further depresses these efficiencies, except at very low average current density.

  8. Solid propellant exhausted aluminum oxide and hydrogen chloride - Environmental considerations

    Science.gov (United States)

    Cofer, W. R., III; Winstead, E. L.; Purgold, G. C.; Edahl, R. A.

    1993-01-01

    Measurements of gaseous hydrogen chloride (HCl) and particulate aluminum oxide (Al2O3) were made during penetrations of five Space Shuttle exhaust clouds and one static ground test firing of a shuttle booster. Instrumented aircraft were used to penetrate exhaust clouds and to measure and/or collect samples of exhaust for subsequent analyses. The focus was on the primary solid rocket motor exhaust products, HCl and Al2O3, from the Space Shuttle's solid boosters. Time-dependent behavior of HCl was determined for the exhaust clouds. Composition, morphology, surface chemistry, and particle size distributions were determined for the exhausted Al2O3. Results determined for the exhaust cloud from the static test firing were complicated by having large amounts of entrained alkaline ground debris (soil) in the lofted cloud. The entrained debris may have contributed to neutralization of in-cloud HCl.

  9. Nickel electrodeposition from leaching solution containing ammonia and chloride

    Institute of Scientific and Technical Information of China (English)

    郑国渠; 郑利峰; 曹华珍; 高志峰; 倪似愚; 张九渊

    2003-01-01

    The effects of temperature, nickel concentration and current density on the current efficiency and the e-lectrolyzer voltage were investigated in the process of electrowinning nickel. The results show that the current effi-ciency is above 90 % under the various experimental conditions, and the electrolyzer voltage is less than that of tradi-tional electrolyzer system. Therefore, the optimized parameters, i.e. temperature of 50 C, current density of 400A/m2 , are determined. It is also elucidated that anodic product is high valent nickel compound in the process of elec-trodeposition in terms of X-ray diffraction and chemical analysis. The amount of solid product formed on the elec-trode surface decreases with an increase in ammonium chloride concentration by cyclic voltammetry analysis. It is al-so indicated that the anodic gas species are mainly composed of nitrogen by vapor phase chromatograph.

  10. Corrosion of LY12 aluminum alloy in sodium chloride solution

    Institute of Scientific and Technical Information of China (English)

    程英亮; 张昭; 曹发和; 李劲风; 张鉴清; 王建明; 曹楚南

    2003-01-01

    The corrosion behavior of LY12 alloy in sodium chloride solution and its electrochemical noise were reported. The development of the micro-pits on the alloy surface was monitored by scanning electron microscopy, scanning tunneling microscopy, and electrochemical noise method. All the measurements show that the corrosion of LY12 alloy can be divided into two stages: a very reactive initial stage and a relative constant stable stage. The initial stage is corresponded to the adsorption of Cl ions and its reaction with the oxide film and the dissolution of Mg containing particles. The stable stage is corresponded to the development of the micro-pits by the galvanic attack formed by Al-Fe-Cu-Mn containing particles and the matrix. The initial stage lasts about 2-3 h while the stable stage dominates the whole corrosion process.

  11. [Toxicity research status of benzalkonium chloride on ocular surface].

    Science.gov (United States)

    Huang, Caihong; Chen, Wensheng; Chen, Yongxiong; Liu, Zuguo

    2014-04-01

    Benzalkonium chloride (BAC) is the most commonly used preservative in ophthalmic preparations.So far large bodies of clinical and experimental studies have shown that use of topical drugs containing BAC can induce a series of ocular surface diseases, such as apoptosis.However, recently, some clinical studies have shown that ocular toxicity in patients treated with eye drops containing BAC has not apparent correlated with BAC.Some scholars consider that the limitations of the research lead people to recognize the BAC toxicity exaggeratedly.Here we summarize numerous clinical and experimental studies of BAC in the past few years, and focus on reviewing recent researches of the toxic effect of BAC on ocular surface.

  12. Interactions of benzalkonium chloride with soft and hard contact lenses

    Energy Technology Data Exchange (ETDEWEB)

    Chapman, J.M.; Cheeks, L.; Green, K. (Medical College of Georgia, Augusta (USA))

    1990-02-01

    We measured the uptake and washout of benzalkonium chloride, using radioactive tracer, by representative hard and soft contact lenses. Uptake by soft contact lenses after 7 days of continuous exposure is high (30 to 56 micrograms/mg of lens weight), with a low percentage of washout in 24 hours (between 0.2% and 1.5% of total uptake). High-water content lenses absorb greater quantities of benzalkonium than do low-water content lenses. Hard lenses take up a much smaller quantity of benzalkonium but release between 30% and 60% of total uptake during washout for 24 hours. Fluorosilicone-acrylate polymer lenses adsorb and release the most preservative, while polymethylmethacrylate lenses (Paragon Optical Inc, Mesa, Ariz) adsorb and release the least. The released benzalkonium from either soft or hard lenses is of a sufficient concentration to be at or above the upper limits of safety.

  13. Poly(vinyl chloride) composite emulsion resins modified by polyurethane

    Institute of Scientific and Technical Information of China (English)

    Xiaolei ZHANG; Mingwang PAN; Shengnan XING; Jingsheng LI

    2008-01-01

    An ionomer-type of polyurethane (PU) emul-sion was prepared from toluene diisocyanate (TDI), polypropylene glycol (PPG) and dimethylol propionic acid (DMPA) following a self-emulsification process. The modified poly(vinyl chloride) (PVC) emulsion resin was obtained by in situ emulsion copolymerization using the PU as seeds in an autoclave. The effects of PU molecular weight on the mechanical properties and thermal stability of the PU/PVC materials were investigated. The composite latex particles and composite materials were determined and characterized using a laser particle size analyzer, transmission electron microscopy or scanning electron microscopy. The study results showed that the PU/PVC hybrid emulsion particles possess a core/shell structure. When the general mechanical properties of the composite materials increase, the thermal stabilities decrease a little. The tough fractures on the surface of the PU/PVC composite sample following impact are quite obvious.

  14. (S,S,S,S)-Nebivolol hydro-chloride hemihydrate.

    Science.gov (United States)

    Rousselin, Yoann; Bruel, Amelie; Clavel, Alexandre

    2012-12-01

    The asymmetric unit of the title hydrated salt, C22H26F2NO4(+)·Cl(-)·0.5H2O, consists of an (S,S,S,S)-nebivolol {nebivol = bis-[2-(6-fluoro-3,4-dihydro-2H-1-benzopyran-2-yl)-2-hy-droxy-eth-yl]ammonium} cation, a chloride anion and a half-occupancy water mol-ecule. The dihedral angle between the mean planes of the benzene rings is 50.34 (12)°. The pyran rings adopt half-chair conformations. The crystal packing features O-H⋯O hydrogen bonds and weak N-H⋯Cl, O-H⋯Cl, and O-H⋯Cl inter-actions, producing layers along (010).

  15. Biotransformation of Tributyltin chloride by Pseudomonas stutzeri strain DN2

    Directory of Open Access Journals (Sweden)

    Dnyanada S. Khanolkar

    2014-12-01

    Full Text Available A bacterial isolate capable of utilizing tributyltin chloride (TBTCl as sole carbon source was isolated from estuarine sediments of west coast of India and identified as Pseudomonas stutzeri based on biochemical tests and Fatty acid methyl ester (FAME analysis. This isolate was designated as strain DN2. Although this bacterial isolate could resist up to 3 mM TBTCl level, it showed maximum growth at 2 mM TBTCl in mineral salt medium (MSM. Pseudomonas stutzeri DN2 exposed to 2 mM TBTCl revealed significant alteration in cell morphology as elongation and shrinkage in cell size along with roughness of cell surface. FTIR and NMR analysis of TBTCl degradation product extracted using chloroform and purified using column chromatography clearly revealed biotransformation of TBTCl into Dibutyltin dichloride (DBTCl2 through debutylation process. Therefore, Pseudomonas stutzeri strain DN2 may be used as a potential bacterial strain for bioremediation of TBTCl contaminated aquatic environmental sites.

  16. The Influence of Additives on Crystallization of Polyvinyl Chloride

    Institute of Scientific and Technical Information of China (English)

    LIU Yaqun; ZHANG Chaocan

    2007-01-01

    Acetanilide, adipic acid and potassium hydrogen phthalate were chosen as nucleating agents of polyvinyl chloride(PVC), and their effects on PVC crystallization were studied by differential scanning calorimetry, wide angle X-ray diffraction and fourier transform infrared spectroscopy. The experimental results indicate that all of the three additives are compatible with PVC to some extent, but adipic acid's compatibility with PVC is less satisfactory. The three additives can improve PVC crystallinity, and acetanilide can decrease PVC glass transition temperature(Tg)and narrow PVC melting range, while adipic acid and potassium hydrogen phthalate rise Tg of PVC and widen its melting range. All additives do not affect PVC crystal system and all samples are in orthorhombic system. All additives can improve (200), (110), (210) and (201, 111) planes growing. Moreover, acetanilide and adipic acid can shrink PVC spacings and improve the crystal perfection of PVC, but potassium hydrogen phthalate swells spacings and reduces the perfection of PVC crystal.

  17. Oxygen and the production of formazan from neotetrazolium chloride.

    Science.gov (United States)

    Butcher, R G

    1978-07-12

    Electrons, generated from dehydrogenase reactions, are transferred to oxygen in preference to neotetrazolium chloride. In model systems in solution the presence of a small amount of oxygen drastically reduces the rate of formazan production. The rate of reaction in tissue sections has been followed using scanning and integrating microdensitometry. As in solution, electrons are transferred preferentially to oxygen. However, oxygen seems unable to diffuse through the incubation medium and thus the supply of oxygen at the site of the enzyme activity becomes exhausted; the time taken to use up the oxygen will depend on the rate of the enzyme activity. It is only then that electrons are passed to the tetrazolium salt and formazan is precipitated.

  18. Sodium Chloride Dihydrate - A Potential Cause of Slippery Accidents

    DEFF Research Database (Denmark)

    Mejlholm, Morten; Thomsen, Kaj; Rasmussen, Peter;

    of ice appearing to be resistant to road salt, a comparative study has been made on a number of different surfaces measuring the friction index. The friction measurements were performed with a Portable Skid-Resistance Tester. Discontinuous surfaces consisting of small islands of hydrohalite...... was classified as potentially slippery surfaces. It is therefore possible that the formation of hydrohalite contributes to accidents on slippery roads.......From a thermodynamic point of view, it can be expected that sodium chloride dihydrate (hydrohalite, NaCl2H2O) will form on winter roads under certain conditions at temperatures below 0.1¢®C. In order to elucidate whether or not the formation of hydrohalite on the pavement can explain the phenomenon...

  19. Allergic contact dermatitis from ethyl chloride and benzocaine.

    Science.gov (United States)

    Carazo, Juan Luis Anguita; Morera, Blanca Sáenz de San Pedro; Colom, Luis Palacios; Gálvez Lozano, José Manuel

    2009-01-01

    Ethyl chloride (EC) or chloroethane (C2H5Cl) is a volatile halogenated hydrocarbon. Reports of contact sensitivity to this gas are infrequent considering its widespread use as a local anesthetic, and it may have a relatively low sensitization potential. Benzocaine is another local anesthetic derivative of the ethyl ester of para-aminobenzoic acid, previously reported as a causative agent of delayed hypersensitivity reactions. We present a patient who developed a generalized itching dermatitis after the application of a medical aerosol containing EC, as well as facial angioedema and tongue swelling after the local application of benzocaine. Patch-test results were positive for EC "as is" (++), benzocaine 5% in petrolatum (++), and caine mix (+++) at 96 hours (day 4). The possibility of cross-sensitization between both drugs would not have been chemically plausible. We report the first published clinical case of contact allergic dermatitis from two chemically unrelated local anesthetics (EC and benzocaine) in the same patient.

  20. Preparation and characterization of organic polymer modified composite polyaluminum chloride

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Compared with traditional aluminum salts, polyaluminum chloride (PACl) has better coagulation-flocculation performance in turbidity removal. However, it is still inferior to organic polymers in terms of bridging function. In order to improve the aggregating property of PACl, different composite PACl flocculants were prepared with various organic polymers. The effect of organic polymer on the distribution of Al (Ⅲ) species in composite flocculants was studied using 27Al NMR and Al-ferron complexation methods. The charge neutralization and surface adsorption characteristics of composite flocculants were also investigated. Jar tests were conducted to evaluate the turbidity removal efficacy of organic polymer modified composite flocculants. The study shows that cationic polymer and anionic polymer have significant influences on the coagulation-flocculation behaviors of PACl. Both cationic and anionic polymers can improve the turbidity removal performance of PACl but the mechanisms are much different: cationic organic polymer mainly increases the charge neutralization ability, but anionic polymer mainly enhances the bridging function.

  1. Structure of concentrated aqueous solutions of scandium chloride

    Science.gov (United States)

    Smirnov, P. R.; Grechin, O. V.

    2017-03-01

    It is shown via X-ray diffraction that aqueous solutions of scandium chloride form ionic associates in a wide range of concentrations. It is established that the Sc3+ ion coordination number increases upon dilution to 8.2 at an unchanged Sc3+-OH2 distance of 0.215 nm. The second coordination sphere of the cation forms at an average distance of 0.420 nm. The number of solvent molecules in the sphere logically increases during dilution. It is concluded that the anion does not form its own sphere in highly concentrated solutions. This coordination sphere begins to form only in solutions with moderate concentrations at a distance of 0.315 nm, and it contains six water molecules in diluted solutions.

  2. Surface Sulfonation of Polyvinyl Chloride by Plasma for Antithrombogenicity

    Institute of Scientific and Technical Information of China (English)

    刘鹏; 陈亚芍

    2004-01-01

    To enhance the blood compatibility of Polyvinyl Chloride (PVC) film, the film was modified by SO2/O2 gas plasma treatment. The effect of surface sulfonation of PVC treated by various SO2/O2 gas plasma depended on the volume ratio O2/(SO2 + 02). When the volumeratio was 0.5, the effect of sulfonation was the best. Sulfonic acid groups were specifically and efficiently introduced onto the PVC surface, which was proved by X-ray photoelectron spectroscopy (XPS) and Attenuated Total Reflectance Fourier Transfer Infrared (ATR-FTIR) spectroscopy. The surface microstructure of modified PVC film was studied with scanning electron microscopy (SEM).The antithrombogenicity of the samples was determined by the activated partial thromboplastin time (APTT), prothrombin time (PT), thrombin time (TT) and plasma recalcification time (PRT)tests and platelet adhesion experiment. The results indicated that the antithrombogenicity of modified PVC was improved remarkably.

  3. Sulfonated polyvinyl chloride fibers for cation-exchange microextraction.

    Science.gov (United States)

    Xu, Li; Lee, Hian Kee

    2009-09-18

    Polyvinyl chloride (PVC) fiber was derivatized by concentrated sulfuric acid to yield sulfonated PVC (PVC-SO3H). The PVC-SO3H fiber had dual properties as a sorbent, based on cation-exchange and hydrophobicity. In the present study, the novel fiber was used directly as an individual device for extraction purposes in the cation-exchange microextraction of anaesthetics, followed by high-performance liquid chromatography-UV analysis. The results demonstrated that this PVC-SO3H fiber-based microextraction afforded convenient operation and cost-effective application to basic analytes. The limits of detection for four anaesthetics ranged from 1.2 to 6.0 ng/mL. No carryover (because of its disposable usage), and no loss of sorbent phase (which normally occurs in stir-bar sorptive extraction) during extraction were observed.

  4. [Test method for 6 phthalates in polyvinyl chloride].

    Science.gov (United States)

    Abe, Yutaka; Mutsuga, Motoh; Hirahara, Yoshichika; Kawamura, Yoko

    2011-01-01

    A test method for 6 phthalates, bis(2-ethylhexyl)phthalate, dibutyl phthalate, benzyl butyl phthalate, diisononyl phthalate, diisodecyl phthalate and di-n-octyl phthalate, in polyvinyl chloride (PVC) was developed. GC/MS was used in the SIM mode for the separation and detection of phthalates. For preparation of the test solution, the extraction method with acetone-hexane mixture (3 : 7) and the dissolution method with tetrahydrofuran and ethanol were compared and it was confirmed that each method gave good recoveries. Dilution of the test solution was effective to reduce the influence of PVC. In a collaborative study with nine laboratories, the intra-laboratory variations showed good repeatability, but the measurements at some laboratories deviated widely. It appears that this method is unsuitable for the judgment of acceptability, but it may be suitable for the determination of phthalate content in PVC products.

  5. Reactivity Ratios of Diethyldiallylammonium Chloride with Acrylamide or Acrylic Acid

    Institute of Scientific and Technical Information of China (English)

    Li Hua LIU; Zhi Qiang LIU; Zhu Qing GONG

    2006-01-01

    The compositions of copolymers of diethyldiallylammonium chloride (DEDAAC) with acrylamide (AM), acrylic acid (AA) or sodium acrylic acid (NaAA) at low conversion were determined by elemental analysis, and the reactivity ratios of monomers in copolymerization were obtained by Kelen-Tudos method. The results showed that the reactivity ratios rDE and rAM are 0.31 and 5.27 for DEDAAC with AM, rDE and rAA are 0.28 and 5.15 for DEDAAC with AA, and rDE and rNaAA are 0.40 and 3.97 for DEDAAC with NaAA, respectively. The copolymerizations for DEDAAC with AM, AA or NaAA are non-ideal copolymerization and the products are random copolymers.

  6. 1-Benzyl-3-[(trimethylsilylmethyl]benzimidazolium chloride monohydrate

    Directory of Open Access Journals (Sweden)

    Mehmet Akkurt

    2010-07-01

    Full Text Available The title compound, C18H23N2Si+·Cl−·H2O, was synthesized from 1-[(trimethylsilylmethyl]benzimidazole and benzyl chloride in dimethylformamide. The benzimidazole ring system is approximately planar, with a maximum deviation of 0.022 (2 Å, and makes an angle of 74.80 (12° with the phenyl ring. The crystal packing is stabilized by O—H...Cl, C—H...Cl, C—H...O and C—H...π interactions between symmetry-related molecules together with π–π stacking interactions between the imidazolium and benzene rings [centroid–centroid distance = 3.5690 (15 Å] and between the benzene rings [centroid–centroid distance = 3.7223 (14 Å].

  7. Electrochemical impedance spectroscopy study on corrosion inhibition of benzyltriethylammonium chloride

    Science.gov (United States)

    Idris, Mohd Nazri; Daud, Abdul Razak; Othman, Norinsan Kamil

    2013-11-01

    Electrochemical Impedance Spectroscopy (EIS) was employed to study the corrosion inhibition behavior of benzyltriethylammonium chloride (BTC) for carbon steel corrosion. The inhibition efficiency was investigated in 1.0 M HCl solution at room temperature (25°C) by varying the BTC concentration. EIS results indicated that the double layer capacitance of electrolyte/carbon steel interface decreases with the increasing of BTC concentration and consequently enhances the polarization resistance of equivalence Randles circuit. The results indicated that inhibition efficiency of as high as 65% could be achieved when 10mM BTC was present in 1.0 M HCl solution as compared to inhibitor-free solution. The inhibition process of BTC on the carbon steel corrosion was found to obey Langmuir adsorption isotherm. This study revealed that BTC is suitable to be used as a corrosion inhibitor in acid media.

  8. Fittings of unplasticized polyvinyl chloride (PVC-U), chlorinated polyvinyl chloride (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure - Dimensions of sockets - Metric series

    CERN Document Server

    International Organization for Standardization. Geneva

    1985-01-01

    Fittings of unplasticized polyvinyl chloride (PVC-U), chlorinated polyvinyl chloride (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure - Dimensions of sockets - Metric series

  9. Neuronal chloride accumulation and excitatory GABA underlie aggravation of neonatal epileptiform activities by phenobarbital.

    Science.gov (United States)

    Nardou, Romain; Yamamoto, Sumii; Chazal, Geneviève; Bhar, Asma; Ferrand, Nadine; Dulac, Olivier; Ben-Ari, Yehezkel; Khalilov, Ilgam

    2011-04-01

    Phenobarbital produces its anti-epileptic actions by increasing the inhibitory drive of γ-aminobutyric acid. However, following recurrent seizures, γ-aminobutyric acid excites neurons because of a persistent increase of chloride raising the important issue of whether phenobarbital could aggravate persistent seizures. Here we compared the actions of phenobarbital on initial and established ictal-like events in an in vitro model of mirror focus. Using the in vitro three-compartment chamber preparation with the two hippocampi and their commissural fibres placed in three different chambers, kainate was applied to one hippocampus and phenobarbital contralaterally, either after one ictal-like event or after many recurrent ictal-like events that produce an epileptogenic mirror focus. Field, perforated patch and single-channel recordings were used to determine the effects of γ-aminobutyric acid and their modulation by phenobarbital, and alterations of the chloride cotransporters were investigated using sodium-potassium-chloride cotransporter 1 and potassium chloride cotransporter 2 antagonists, potassium chloride cotransporter 2 immunocytochemistry and sodium-potassium-chloride cotransporter 1 knockouts. Phenobarbital reduced initial ictal-like events and prevented the formation of a mirror focus when applied from the start. In contrast, phenobarbital aggravated epileptiform activities when applied after many ictal-like events by enhancing the excitatory actions of γ-aminobutyric acid due to increased chloride. The accumulation of chloride and the excitatory actions of γ-aminobutyric acid in mirror foci neurons are mediated by the sodium-potassium-chloride cotransporter 1 chloride importer and by downregulation and internalization of the chloride-exporter potassium-chloride cotransporter 2. Finally, concomitant applications of the sodium-potassium-chloride cotransporter 1 antagonist bumetanide and phenobarbital decreased excitatory actions of γ-aminobutyric acid and

  10. Treatment of Highly Turbid Water by Polyaluminum Ferric Chloride (PAFCL

    Directory of Open Access Journals (Sweden)

    Fazel Fazel Mohammadi-Moghaddam

    2015-10-01

    Full Text Available Background & Aims of the Study: In some situation like rainfall seasons raw water become very turbid so it affected the water treatment plant processes and quality of produced water. Treatment of very high turbid water has some concerns like precursors for disinfection by-products and very loading rate of particle on filter's media and consequently increases in water consumption for filter backwash. This paper investigates the performance of a composite inorganic polymer of aluminium and ferric salt, Polyaluminium ferric chloride (PAFCl, for the removal of turbidity, color and natural organic matter (NOM from high turbid water. Materials and Methods: Experiments were carried out by Jar test experiment by synthetic water samples with 250 and 500 NTU turbidity that prepared in laboratory. Results: The results of conventional jar test showed that the optimum pH for coagulation of water sample was 7.5 to 8 and optimum dosage of the coagulant was 10 mg/L. Removal efficiency of turbidity, color and UV adsorbent at 254 nm at optimum dose and pH without filtration was 99.92%, 100% and 80.6% respectively for first sample (250 NTU and 99.95%, 99.49% and 84.77 for second sample (500 NTU respectively. Conclusion: It concluded that polyaluminium ferric chloride has a very good efficiency for the removal of turbidity, color and organic matter in high turbid water. Also it can be select as a coagulant for high turbid water and some waste water from water treatment plant like filter backwash water.

  11. Effect of kaolin treatment temperature on mortar chloride permeability

    Directory of Open Access Journals (Sweden)

    Puertas, F.

    2007-03-01

    Full Text Available The present paper discusses the results of chloride resistance tests conducted on ordinary Portland cement (OPC mortars containing a Colombian kaolin pre-treated at temperatures of from 600 to 800 ºC. The resulting metakaolin (MK was added to OPC mortar mixes in proportions of 10 and 20% by cement weight. The mortars were compared for physical and chemical properties, including capillary absorption, chloride permeability and pore microstructure as assessed by mercury porosimetry. The best performance was recorded for the samples containing 20% of the material treated at 800 ºC.En el presente trabajo se incluyen los resultados de la resistencia a la penetración de cloruros de morteros de Cemento Portland Ordinario (OPC adicionados con un caolín colombiano sometido a tratamiento térmico en un rango de temperaturas entre 600 y 800 °C. Los productos del tratamiento térmico, metacaolín (MK, son incorporados en mezclas de morteros de OPC en proporciones del 10 y 20% en relación al peso del cemento. Se comparan sus características físico-químicas, entre las cuales se incluye la microestructura de poros evaluada por la técnica de porosimetría de mercurio, con la absorción capilar y la permeabilidad a cloruros. Se concluye que las muestras adicionadas con un 20% del material tratado térmicamente a 800 °C presentan el mejor desempeño en sus propiedades finales.

  12. Matrix metalloproteinase inhibitory properties of benzalkonium chloride stabilizes adhesive interfaces.

    Science.gov (United States)

    Sabatini, Camila; Patel, Shaival K

    2013-12-01

    This study evaluated the effects of different concentrations of benzalkonium chloride (BAC) on the preservation of adhesive interfaces created with two etch-and-rinse adhesives and its inhibitory properties on dentin matrix metalloproteinase (MMP) activity. The following groups were tested with the adhesive systems Optibond Solo Plus and All-Bond 3: Group 1, adhesive without inhibitor (control); Group 2, topical 2.0% chlorhexidine (2.0% CHX); Group 3, phosphoric acid with 1.0%wt BAC (BAC-PA); Group 4, 0.25% BAC-adhesive (0.25% BAC); Group 5, 0.5% BAC-adhesive (0.5% BAC); Group 6, 1.0% BAC-adhesive (1.0% BAC); and Group 7, 2.0% BAC-adhesive (2.0% BAC). Composite cylinders were fabricated, and shear bond strength (SBS) was evaluated after 24 h, 6 months, and 18 months of storage. Extracts from concentrated demineralized human dentin powder were subjected to SDS-PAGE and incubated in the presence of 0.25, 0.5, 1.0, and 2.0% BAC. Overall, stable bonds were maintained for 18 months. Improved bond strengths were seen for 0.5% BAC and 1.0% BAC when bonding with Optibond Solo Plus, and for 0.25% BAC and 0.5% BAC when bonding with All-Bond 3. Zymographic analysis revealed complete inhibition of gelatinolytic activity with BAC. Benzalkonium chloride, at all concentrations, inhibited dentin proteolytic activity, which seems to have contributed to the improved bond stability after 18 months for specific combinations of BAC concentration and adhesive.

  13. Lack of conventional ATPase properties in CFTR chloride channel gating.

    Science.gov (United States)

    Schultz, B D; Bridges, R J; Frizzell, R A

    1996-05-01

    CFTR shares structural homology with the ABC transporter superfamily of proteins which hydrolyze ATP to effect the transport of compounds across cell membranes. Some superfamily members are characterized as P-type ATPases because ATP-dependent transport is sensitive to the presence of vanadate. It has been widely postulated that CFTR hydrolyzes ATP to gate its chloride channel. However, direct evidence of CFTR hydrolytic activity in channel gating is lacking and existing circumstantial evidence is contradictory. Therefore, we evaluated CFTR chloride channel activity under conditions known to inhibit the activity of ATPases; i.e., in the absence of divalent cations and in the presence of a variety of ATPase inhibitors. Removal of the cytosolic cofactor, Mg2+, reduced both the opening and closing rates of CFTR suggesting that Mg2+ plays a modulatory role in channel gating. However, channels continued to both open and close showing that Mg2+ is not an absolute requirement for channel activity. The nonselective P-type ATPase inhibitor, vanadate, did not alter the gating of CFTR when used at concentrations which completely inhibit the activity of other ABC transporters (1 mM). Higher concentrations of vanadate (10 mM) blocked the closing of CFTR, but did not affect the opening of the channel. As expected, more selective P-type (Sch28080, ouabain), V-type (bafilomycin A1, SCN-) and F-type (oligomycin) ATPase inhibitors did not affect either the opening or closing of CFTR. Thus, CFTR does not share a pharmacological inhibition profile with other ATPases and channel gating occurs in the apparent absence of hydrolysis, although with altered kinetics. Vanadate inhibition of channel closure might suggest that a hydrolytic step is involved although the requirement for a high concentration raises the possibility of previously uncharacterized effects of this compound. Most conservatively, the requirement for high concentrations of vanadate demonstrates that the binding site for

  14. A molecular dynamics study of chloride binding by the cryptand SC24

    Science.gov (United States)

    Owenson, B.; MacElroy, R. D.; Pohorille, A.

    1988-01-01

    The capture of chloride from water by the tetraprotonated form of the spherical macrotricyclic molecule SC24 was studied using molecular dynamics simulation methods. This model ionophore represents a broad class of molecules which remove ions from water. Two binding sites for the chloride were found, one inside and one outside the ligand. These sites are separated by a potential energy barrier of approximately 20 kcal mol-1. The major contribution to this barrier comes from dehydration of the chloride. The large, unfavorable dehydration effect is compensated for by an increase in electrostatic attraction between the oppositely charged chloride and cryptand, and by energetically favorable rearrangements of water structure. Additional assistance in crossing the barrier and completing the dehydration of the ion is provided by the shift of three positively charged hydrogen atoms of the cryptand towards the chloride. This structural rigidity is partially responsible for its selectivity.

  15. Investigation of the reactions of chlorides binding to aluminates using XRD and DTA methods

    Directory of Open Access Journals (Sweden)

    Bikić Farzet H.

    2009-01-01

    Full Text Available The reactions of chlorides binding to aluminates were investigated by analyzing the monochloroaluminate hydrate, product of the reaction. The results show that the product is formed in the fresh concrete, after adding chloride within the stage of the preparation of concrete, as well as adding chlorides by penetration from the environment into the concrete. The obtained results are significant, considering the aspect of preventing corrosion of the steel reinforcement into the concrete. It is known that only free chlorides activate corrosion processes in the steel reinforcement in concrete. The process of chloride bonding is followed by X-ray diffraction (XRD and differential thermal (DTA analysis of samples of the cement paste, which is the process of preparation and care is described in detail in this work.

  16. Chloride stress corrosion cracking of Alloy 600 in boric acid solutions

    Energy Technology Data Exchange (ETDEWEB)

    Berge, Ph. [Electricite de France, 92 - Paris la Defense (France); Noel, D.; Gras, J.M.; Prieux, B. [Electricite de France, 77 - Moret-sur-Loing (France). Direction des Etudes et Recherches

    1997-10-01

    The high nickel austenitic alloys are generally considered to have good resistance to chloride stress corrosion cracking. In the standard boiling magnesium chloride solution tests, alloys with more than 40% nickel are immune. Nevertheless, more recent data show that cracking can occur in both Alloys 600 and 690 if the solution is acidified. In other low pH media, such as boric acid solution at 100 deg C, transgranular and intergranular cracking are observed in Alloy 600 in the presence of minor concentrations of sodium chloride (2g/I). In concentrated boric acid at higher temperatures (250 and 290 deg C), intergranular cracking also occurs, either when the chloride concentration is high, or at low chloride contents and high oxygen levels. The role of pH and a possible specific action of boric acid are discussed, together with the influence of electrochemical potential. (author) 21 refs.

  17. Anaerobic mineralization of vinyl chloride in Fe(III)-reducing, aquifer sediments

    Science.gov (United States)

    Bradley, P.M.; Chapelle, F.H.

    1996-01-01

    Within anaerobic aquifer systems, reductive dehalogenation of polychlorinated ethenes commonly results in the accumulation of vinyl chloride, which is highly toxic and carcinogenic to humans. Anaerobic reduction of vinyl chloride is considered to be slow and incomplete. Here, we provide the first evidence for anaerobic oxidation of vinyl chloride under Fe(III)reducing conditions. Addition of chelated Fe(III) (as Fe-EDTA) to anaerobic aquifer microcosms resulted in mineralization of up to 34% of [1,2- 14C]vinyl chloride within 84 h. The results indicate that vinyl chloride can be mineralized under anaerobic, Fe(III)-reducing conditions and that the bioavailability of Fe(III) is an important factor affecting the rates of mineralization.

  18. Friction and wear performances of borates and lanthanum chloride in water

    Institute of Scientific and Technical Information of China (English)

    CHEN Boshui; FANG Jianhua; WANG Jiu; LI Jia; LOU Fang

    2008-01-01

    The antiwear and friction-reducing performances of sodium borate, potassium borate and lanthanum chloride in water were evaluated on a four-ball friction tester. The topographies, element distribution and chemical characteristics of the worn surfaces were investigated by scanning electron microscope (SEM), energy dispersion of X-ray (EDX) and X-ray photoelectron spectroscope (XPS). The results indicated that sodium borate, potassium borate and lanthanum chloride increased extreme pressure, antiwear and friction-reducing capacities of water to a certain extent, of which potassium borate was the best candidate. Combination of lanthanum chloride with sodium borate and potassium borate respectively further improved antiwear and friction-reducing capacities. Scratches of worn surfaces lubricated with water containing borates and lanthanum chloride were less severe than those lubricated with water containing borates alone. A tribochemical film mainly composed of oxides of lanthanum, boron and iron reduced friction and wear for water lubricant formulated with both borates and lanthanum chloride.

  19. Present limitations of models for predicting chloride ingress into reinforced concrete structures Present

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, L.O. [Lund Institute of Technology, Laboratory of Building Materials, PO Box 118, 221 00 Lund (Sweden)

    2006-07-01

    Models to predict chloride ingress are numerous but all of them have serious limitations that restrict the present use for long term predictions. An overview is given of the fundamental differences between various models, from those based on Fick's 2. with constant or time-dependent diffusion coefficients and surface chloride contents, to those based on chloride transport equations with or without a multi-species approach. The key advantages and limitations of each type of model are identified and the research needs are summarized and discussed. The three main limitations are shown to be (i) the lack of understanding the time-dependency of the apparent chloride diffusion coefficients, (ii) the lack of good long-term data, the chloride content increase with time close to the exposed surface and (iii) the difficulties in quantifying the boundary conditions for sophisticated ingress models. (author)

  20. Present limitations of models for predicting chloride ingress into reinforced concrete structures

    Science.gov (United States)

    Nilsson, L.-O.

    2006-11-01

    Models to predict chloride ingress are numerous but all of them have serious limitations that restrict the present use for long term predictions. An overview is given of the fundamental differences between various models, from those based on Fick's 2nd with constant or time-dependent diffusion coefficients and surface chloride contents, to those based on chloride transport equations with or without a multi-species approach. The key advantages and limitations of each type of model are identified and the research needs are summarized and discussed. The three main limitations are shown to be (i) the lack of understanding the time-dependency of the apparent chloride diffusion coefficients, (ii) the lack of good long-term data, the chloride content increase with time close to the exposed surface and (iii) the difficulties in quantifying the boundary conditions for sophisticated ingress models.

  1. Erratum to: Study on Chloride Ion Penetration Resistance of Rubberized Concrete Under Steady State Condition

    Directory of Open Access Journals (Sweden)

    Md Noor Nurazuwa

    2016-01-01

    In this paper, the effect of crumb rubber, CR as fine aggregate in the concrete to enhance concrete durability against chloride ion diffusion was studied. Chloride ion diffusion in rubberized concrete was tested by migration test under steady state condition. Concrete specimen with water-to-cement ratio of 0.50 was prepared to study the CR effectiveness in comparison with lower water-to-cement ratio. In addition, 10% silica fume, SF was added to provide denser concrete and to understand its effectiveness against chloride ion diffusion. Results showed that chloride transport characteristics were improved by the increasing amount of CR in all mixed due to the fact that CR has the ability to repel water. Meanwhile, rubberized concrete with w/c = 0.35 gave better resistance against chloride ion penetration compared to w/c = 0.50. This was much improved with combination of CR and SF.

  2. TESTING OF 304L STAINLESS STEEL IN NITRIC ACID ENVIRONMENTS WITH FLUORIDES AND CHLORIDES

    Energy Technology Data Exchange (ETDEWEB)

    Mickalonis, J.

    2010-10-04

    Impure radioactive material processed in nitric acid solutions resulted in the presence of chlorides in a dissolver fabricated from 304L stainless steel. An experimental program was conducted to study the effects of chloride in nitric acid/fluoride solutions on the corrosion of 304L stainless steel. The test variables included temperature (80, 95, and 110 C) and the concentrations of nitric acid (6, 12, and 14 M), fluoride (0.01, 0.1, and 0.2 M) and chloride (100, 350, 1000, and 2000 ppm). The impact of welding was also investigated. Results showed that the chloride concentration alone was not a dominant variable affecting the corrosion, but rather the interaction of chloride with fluoride significantly affected corrosion.

  3. Cystic Fibrosis Gene Encodes a cAMP-Dependent Chloride Channel in Heart

    Science.gov (United States)

    Hart, Padraig; Warth, John D.; Levesque, Paul C.; Collier, Mei Lin; Geary, Yvonne; Horowitz, Burton; Hume, Joseph R.

    1996-06-01

    cAMP-dependent chloride channels in heart contribute to autonomic regulation of action potential duration and membrane potential and have been inferred to be due to cardiac expression of the epithelial cystic fibrosis transmembrane conductance regulator (CFTR) chloride channel. In this report, a cDNA from rabbit ventricle was isolated and sequenced, which encodes an exon 5 splice variant (exon 5-) of CFTR, with >90% identity to human CFTR cDNA present in epithelial cells. Expression of this cDNA in Xenopus oocytes gave rise to robust cAMP-activated chloride currents that were absent in control water-injected oocytes. Antisense oligodeoxynucleotides directed against CFTR significnatly reduced the density of cAMP-dependent chloride currents in acutely cultured myocytes, thereby establishing a direct functional link between cardiac expression of CFTR protein and an endogenous chloride channel in native cardiac myocytes.

  4. Electroanalytical determination of trace chloride in room-temperature ionic liquids.

    Science.gov (United States)

    Villagrán, Constanza; Banks, Craig E; Hardacre, Christopher; Compton, Richard G

    2004-04-01

    The electroanalytical quantification of chloride in [C4mim][BF4], [C4mim][NTf2], and [C4mim][PF6] ionic liquids has been explored using linear sweep and square wave voltammetry. Cathodic stripping voltammetry at a silver disk electrode is found to be the most sensitive. The methodology is based on first holding the potential of the electrode at +2.0 V (vs Ag wire), to accumulate silver chloride at the electrode. On applying a cathodic scan, a stripping wave is observed corresponding to the reduction of the silver chloride. This stripping protocol was found to detect ppb levels of chloride in [C4mim][BF4], [C4mim][NTf2], and [C4mim][PF6]. Although other methods for chloride have been reported for [BF4](-)- and [PF6](-)-based ionic liquids, no methods have been reported for [NTf2](-) ionic liquids.

  5. Host-Guest Strategy to Reversibly Control a Chloride Carrier Process with Cyclodextrins.

    Science.gov (United States)

    Gravel, Julien; Kempf, Julie; Schmitzer, Andreea

    2015-12-14

    Herein, we report a reversible modular chloride transport process based on host-guest competitive interactions between an imidazolium-based chloride carrier and beta-cyclodextrin. We report evidence for the formation of the supramolecular complex between 1,3-bis(2-(adamantan-1-yl)ethyl)imidazolium bis(trifluorometyl-sulfonyl)imide with two β-cyclodextrins. Through fluorescence assays in liposomes and black lipid membrane experiments, we demonstrate that the formation of the supramolecular complex results in the inhibition of the chloride transport. We show that the chloride transport process can be entirely restored in the presence of competitive adamantyl-functionalized guests. This is the first example of an entirely reversible modular chloride transport process in phospholipid bilayers involving a mobile carrier transporter and cyclodextrin supramolecular complex.

  6. Strength, porosity, and chloride resistance of mortar using the combination of two kinds of pozzolanic materials

    Science.gov (United States)

    Rukzon, Sumrerng; Chindaprasirt, Prinya

    2013-08-01

    This article presents a study on the resistance to chloride penetration, corrosion, porosity, and strength of mortar containing fine fly ash (FA), ground rice husk-bark ash (RB), and ground bagasse ash (BA). Ordinary Portland cement (CT) was blended with a single pozzolan and two pozzolans. Strength, porosity, rapid chloride penetration, immersion, and corrosion tests were performed to characterize the mortar. Test results showed that the use of ternary blends of CT, FA, and RB or BA decreased the porosity of the mortar, as compared with binary blended mortar containing CT and RB or BA. The resistance to chloride penetration of the mortar improved substantially with partial replacement of CT with FA, RB, and BA. The use of ternary blends of CT, FA and RB or BA produced the mortar with good strength and resistance to chloride penetration. The resistance to chloride penetration was higher with an increase in the replacement level due to the reduced calcium hydroxide.

  7. Vitamin E and Sodium Selenite Against Mercuric Chloride-Induced Lung Toxicity in the Rats

    Directory of Open Access Journals (Sweden)

    Emine Celikoglu

    2015-08-01

    Full Text Available The aim of the present study was to elucidate the possible protective role of vitamin E and / or sodium selenite on mercuric chloride-induced oxidative stress and histopathological changes in the lung tissue of the rats. Adult male albino Wistar rats were exposed to mercuric chloride (1.0 mg/kg day for four weeks. Treatment with mercuric chloride led to oxidative stress by enhancing MDA level and also decreasing superoxide dismutase (SOD, catalase (CAT glutathione peroxidase (GPx and glutathione S transferaz (GST activities. However, mercuric chloride exposure resulted in histopathological changes in the lung tissue in the rats. MDA level and SOD, CAT GPx and GST activities and histopathological changes modulated in concomitantly supplementation of vitamin E (100 mg/kg day and /or sodium selenite (0.25 mg/kg day to mercuric chloride-treated groups.

  8. The influence of cement type and temperature on chloride binding in cement paste

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede; Korzen, Migge Sofie Hoffmann; Skibsted, Jørgen

    1998-01-01

    This paper describes effects of cement type and temperature on chloride binding in cement paste, which is an important subject in relation to life-time modelling of reinforced concrete structures. The influence of cement type on chloride binding is investigated by substituting cement with pure...... cement clinker. Both theoretical considerations and experimental data for chloride binding in cement pastes are presented. A physico-chemically based model to describe the influence of temperature on physical binding of chloride is presented. Solid-state 27Al and 29Si magic-angle spinning (MAS) nuclear...... magnetic resonance (NMR) spectroscopy has been used for quantification of the anhydrous and hydrated aluminate and silicate phases in the chloride exposed cement pastes. The 27Al isotropic chemical shift and nuclear quadrupole coupling is reported for a synthetic sample of Friedel's salt, Ca2Al(OH)6Cl×2H2O....

  9. Corrosion of reinforcement induced by environment containing chloride and carbon dioxide

    Indian Academy of Sciences (India)

    Vladimír Živica

    2003-10-01

    Reinforced concrete structures during their exploitation may be exposed to the common action of carbonation and chlorides causing corrosion of steel reinforcement. Therefore, the related data seem to be interesting and important when the evaluation of the service life of the structures is the object of interest. This fact was a motivation for the present experimental study on the sequence of action of chloride solutions and carbonation of the embedding concrete. The results obtained show that carbonation of concrete foregoing the action of chloride solutions may intensify the process of corrosion of steel reinforcement in comparison to the converse sequence of the action of mentioned media. At the same time the natrium chloride solution has been shown as a more aggressive medium opposite to the calcium and magnesium chloride solutions.

  10. Spectroscopic study of the electrochemical behaviour of tantalum(V) chloride and oxochloride species in 1-butyl-1-methylpyrrolidinium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Babushkina, Olga B., E-mail: olga.babushkina@cest.a [Centre in Electrochemical Surface Technology (CEST), Viktor Kaplan street 2, A-2700, Wiener Neustadt (Austria); Ekres, Silvia [Centre in Electrochemical Surface Technology (CEST), Viktor Kaplan street 2, A-2700, Wiener Neustadt (Austria)

    2010-12-30

    FTIR spectroscopy was used to identify the oxochloride species of tantalum(V) in ionic liquids and to confirm the correlations between their presence in electrolytes and the changes in the route of electrochemical reduction of tantalum(V). Electrochemical behaviour of the mixtures (x)1-butyl-1-methyl-pyrrolidinium chloride-(1 - x)TaCl{sub 5} at x = 0.80, 0.65, and 0.40 was investigated over the temperature range 90-160 {sup o}C with respect to the electrochemical deposition of tantalum and was discussed in terms of spectroscopic data. The mechanism of electrochemical reduction of tantalum(V) in the basic and acidic electrolytes depends strongly on the structure and composition of the electro active species of tantalum(V) defined by the molar composition of ionic liquids and on the competition between tantalum(V) chloride and oxochloride species. In the basic mixture at x = 0.80, with octahedral [TaCl{sub 6}]{sup -} ions as the electrochemically active species only the first reduction step Ta{sup 5+} {yields} Ta{sup 4+} at -0.31 V was observed. The competitive reduction of tantalum(V) oxochloride species occurs at more anodic potential (-0.01 V) than the reduction of the chloride complexes and can restrict the further reduction of tantalum(IV). In the basic ionic liquid at x = 0.65, the cyclic voltammograms exhibit reduction peaks at -0.31 V and -0.51 V attributed to the diffusion controlled process as [TaCl{sub 6}]{sup -} + e{sup -} {yields} [TaCl{sub 6}]{sup 2-} and [TaCl{sub 6}]{sup 2-} + e{sup -} {yields} [TaCl{sub 6}]{sup 3-}. The further irreversible reduction of tantalum(III) to metallic state may occur at -2.1 V. In the acidic ionic liquids, at x = 0.40 the electrochemical reduction of two species occurs, TaCl{sub 6}{sup -} and Ta{sub 2}Cl{sub 11}{sup -} and it is limited by two electron transfer for both of them at -0.3 V and -1.5 V, respectively.

  11. Protective Role of Sodium Selenite on Mercuric Chloride Induced Oxidative and Renal Stress in Rats

    Directory of Open Access Journals (Sweden)

    Necib, Youcef

    2013-04-01

    Full Text Available Backgroud: Reactive oxygen species are known to play a major role in mercuric chloride induced oxidative and renal stress. Sodium selenite as an exogenous source of selenium is used for endogenous selenoprotein synthesis to scavenge the free radicals. The study was designed to investigate the possible protective role of sodium selenite in mercuric chloride induced renal stress, by using biochemical approaches. Adult male Albinos Wistar rats were randomly divided into four groups. The first group was served as the control, the second group was given sodium selenite (0.25 mg/kg b.w, while the third group was given mercuric chloride (0.25 mg/kg, finally, the fourth group was given combined treatment of sodium selenite and mercuric chloride for 3 weeks.Results: The effects of sodium selenite on mercuric chloride induced oxidative and renal stress were evaluated by serum creatinine, urea, uric acid, billirubin levels and LDH activity, kidney tissue lipid peroxidation, GSH levels, GSH-Px, GST and catalase activities and hematological parameters. Administration of mercuric chloride induced significant increase in serum: creatinine, urea, uric acid and billirubin concentration showing renal stress. Mercuric chloride also induced oxidative stress, as indicate by decreased kidney tissue of GSH level, GSH-Px, GST, and catalase activities along with increase the level of lipid peroxidation. Furthermore, treatment with mercuric chloride caused a marked elevation of kidney weight and decreased body weight and erythrocytes, hemoglobin, hematocrit levels. Sodium selenite treatment markedly reduced elevated serum: creatinine, urea, uric acid and billirubin levels, and LDH activity and conteracted the deterious effects of mercuric chloride on oxidative stress markers and hematological parameters and atteneuated histopathological changes caused by HgCl2 in kidney.Conclusion: Our results indicate that sodium selenite could have a beneficial role against mercuric

  12. Pharmacological analysis of epithelial chloride secretion mechanisms in adult murine airways.

    Science.gov (United States)

    Gianotti, Ambra; Ferrera, Loretta; Philp, Amber R; Caci, Emanuela; Zegarra-Moran, Olga; Galietta, Luis J V; Flores, Carlos A

    2016-06-15

    Defective epithelial chloride secretion occurs in humans with cystic fibrosis (CF), a genetic defect due to loss of function of CFTR, a cAMP-activated chloride channel. In the airways, absence of an active CFTR causes a severe lung disease. In mice, genetic ablation of CFTR function does not result in similar lung pathology. This may be due to the expression of an alternative chloride channel which is activated by calcium. The most probable protein performing this function is TMEM16A, a calcium-activated chloride channel (CaCC). Our aim was to assess the relative contribution of CFTR and TMEM16A to chloride secretion in adult mouse trachea. For this purpose we tested pharmacological inhibitors of chloride channels in normal and CF mice. The amplitude of the cAMP-activated current was similar in both types of animals and was not affected by a selective CFTR inhibitor. In contrast, a CaCC inhibitor (CaCCinh-A01) strongly blocked the cAMP-activated current as well as the calcium-activated chloride secretion triggered by apical UTP. Although control experiments revealed that CaCCinh-A01 also shows inhibitory activity on CFTR, our results indicate that transepithelial chloride secretion in adult mouse trachea is independent of CFTR and that another channel, possibly TMEM16A, performs both cAMP- and calcium-activated chloride transport. The prevalent function of a non-CFTR channel may explain the absence of a defect in chloride transport in CF mice.

  13. Estimation of Groundwater Recharge at Pahute Mesa using the Chloride Mass-Balance Method

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, Clay A [DRI; Hershey, Ronald L [DRI; Healey, John M [DRI; Lyles, Brad F [DRI

    2013-07-01

    Groundwater recharge on Pahute Mesa was estimated using the chloride mass-balance (CMB) method. This method relies on the conservative properties of chloride to trace its movement from the atmosphere as dry- and wet-deposition through the soil zone and ultimately to the saturated zone. Typically, the CMB method assumes no mixing of groundwater with different chloride concentrations; however, because groundwater is thought to flow into Pahute Mesa from valleys north of Pahute Mesa, groundwater flow rates (i.e., underflow) and chloride concentrations from Kawich Valley and Gold Flat were carefully considered. Precipitation was measured with bulk and tipping-bucket precipitation gauges installed for this study at six sites on Pahute Mesa. These data, along with historical precipitation amounts from gauges on Pahute Mesa and estimates from the PRISM model, were evaluated to estimate mean annual precipitation. Chloride deposition from the atmosphere was estimated by analyzing quarterly samples of wet- and dry-deposition for chloride in the bulk gauges and evaluating chloride wet-deposition amounts measured at other locations by the National Atmospheric Deposition Program. Mean chloride concentrations in groundwater were estimated using data from the UGTA Geochemistry Database, data from other reports, and data from samples collected from emplacement boreholes for this study. Calculations were conducted assuming both no underflow and underflow from Kawich Valley and Gold Flat. Model results estimate recharge to be 30 mm/yr with a standard deviation of 18 mm/yr on Pahute Mesa, for elevations >1800 m amsl. These estimates assume Pahute Mesa recharge mixes completely with underflow from Kawich Valley and Gold Flat. The model assumes that precipitation, chloride concentration in bulk deposition, underflow and its chloride concentration, have been constant over the length of time of recharge.

  14. Correlation between chloride flux via the mitochondria-rich cells and transepithelial water movement in isolated frog skin (Rana esculenta)

    DEFF Research Database (Denmark)

    Nielsen, Robert

    1995-01-01

    Antidiuretic hormone; chloride transport; electroosmosis; Frog skin; Intercalated cells; Local osmosis; Mitochondria-rich cells.......Antidiuretic hormone; chloride transport; electroosmosis; Frog skin; Intercalated cells; Local osmosis; Mitochondria-rich cells....

  15. The Effect of Protic Acid Identity on the Structures of Complexes with Vinyl Chloride: Fourier Transform Microwave Spectroscopy and Molecular Structure of the Vinyl Chloride-Hydrogen Chloride Complex

    Science.gov (United States)

    Messinger, Joseph P.; Leung, Helen O.; Marshall, Mark D.

    2014-06-01

    In all previous examples of complexes formed between protic acids and haloethylenes, we have observed similar modes of binding regardless of the specific identity of the acid, HF, HCl, or HCCH. Although details of the structures, such as hydrogen bond length and amount of deviation from linearity, do reflect the strength of the interaction and show clear correlations with the gas-phase acidity, the complexes of a given haloethylene with any of the acids have identical structural motifs. Vinyl chloride, on the other hand, has been observed to adopt different modes of binding in its interactions with HF and HCCH. The HF complex, reported two years ago, has a geometry with HF interacting across the double bond of vinyl chloride and forming a secondary interaction with the hydrogen cis to the chlorine atom, but in the complex with acetylene, reported last year, HCCH locates at one end of the vinyl chloride with the secondary interaction occurring with the geminal hydrogen atom. This variety continues and is expanded in the vinyl chloride-HCl complex. Ab initio theory predicts a complex that has the HCl molecule interacting across the double bond, but located out of the vinyl chloride plane. The microwave spectrum of the most abundant isotopologue of this complex is consistent with theoretical predictions and additionally shows the presence of large amplitude motion connecting two equivalent structures.

  16. A comprehensive analysis of plausible genotoxic covariates among workers of a polyvinyl chloride plant exposed to vinyl chloride monomer.

    Science.gov (United States)

    Kumar, Alagamuthu Karthick; Balachandar, Vellingiri; Arun, Meyyazhagan; Ahamed, Shafi Ahammed Khan Mustaq; Kumar, Shanmugam Suresh; Balamuralikrishnan, Balasubramanium; Sankar, Kathannan; Sasikala, Keshavarao

    2013-05-01

    The aim of this study was to assess the frequency of chromosomal aberrations-including chromatid type aberrations (CTAs), chromosomal type aberrations, micronucleus (MN) comet assay, and XRCC1 399 Arg/Gln polymorphism-in peripheral blood lymphocytes of workers occupationally exposed to vinyl chloride monomer (VCM). A total of 52 workers and an equal number of controls were recruited into the study to explore the potential cytogenetic risk of occupational exposure to VCM. Questionnaires were administered to obtain details of habitual cigarette-smoking, alcohol-consumption pattern, and occupation, etc. The exposed subjects and controls were classified into two groups based on age (group I 8 and ≥8 years). CTA, MN, and comet assay frequency were significantly greater in polyvinyl chloride (PVC) factory workers (p < 0.05) with long-duration work. CTA, MN, and comet assay values were found to be increased with age in exposed subjects as well as in controls, with exposed subjects showing a statistically greater degree. An extensively greater MN frequency was observed in smokers exposed to VCM than in the control group (P < 0.05). The mean tail length of exposed subjects was greater compared with controls. The study on XRCC1 399 Arg/gln polymorphism in PVC factory workers showed less significant difference in allele frequency compared with controls. In conclusion, this results of work provides evidence for an apparent genotoxic effect associated with VCM exposure. Our results reinforce the greater sensitivity of cytogenetic assays for biomonitoring of occupationally exposed populations. Statistics indicate that workers exposed to VCM are at carcinogenic risk and should be monitored for long-term adverse effects from their exposure.

  17. Stability of Melphalan in 0.9% Sodium Chloride Solutions Prepared in Polyvinyl Chloride Bags for Intravenous Injection.

    Science.gov (United States)

    Desmaris, Romain-Pacôme; Mercier, Lionel; Paci, Angelo

    2015-09-01

    Melphalan is an alkylating agent frequently used in an intravenous formulation to treat hematologic malignancies and solid tumors in both adults and children. According to the manufacturer, melphalan is stable in sterile 0.9% sodium chloride for 90 min at room temperature (RT). Several authors have studied the stability of different concentrations of melphalan; however, most were not adapted to the current manufacturing process applied in pharmaceutical centralized units. This study was conducted to determine the stability of melphalan in 0.9% sodium chloride solutions at concentrations used for intravenous injection in practice. Melphalan is commonly prepared in diluted solutions ranging from 2 to 4 mg/ml for the treatment of adult patients and at lower concentrations (down to 0.5 mg/ml) for pediatric use. Accordingly, these were the three concentrations chosen for this study. Melphalan concentrations were measured with high-performance thin-layer chromatography (HPTLC). At RT, admixtures prepared at 4 mg/ml were stable for up to 8 h without protection from light; however, at lower concentrations, such as 0.5 and 2 mg/ml, stability did not exceed 2 h. When refrigerated, melphalan was stable for 24 h at 2 mg/ml; however, at 0.5 and 4 mg/ml, the drug was not stable. Melphalan solutions present with limited stability at 0.5, 2, and 4 mg/ml and are not adapted for delayed administration in pharmaceutical centralized units. However, at 4 mg/ml and at RT, a stability of 8 h is very interesting in practice and allows sufficient time for preparation, pharmaceutical control, transport, and administration.

  18. Influence of chemical bonding of chlorides with aluminates in cement hidratation process on corrosion steel bars in concrete

    Directory of Open Access Journals (Sweden)

    Bikić Farzet H.

    2010-01-01

    Full Text Available The presence of chlorides in concrete is a permanent subject of research because they cause corrosion of steel bars. Chlorides added to the concrete during preparation, as accelerators of the bonding of cement minerals process, enter into reaction with aluminates, creating a phase known as chloroaluminate hydrates. In everyday conditions the product of chemical bonding between chlorides and aluminates is usually monochloridealuminate C3A·CaCl2·Hx, better known as Friedel's salt. In this paper, the influence of chemical bonding of chlorides with aluminates during the process of cement hydration on corrosion of steel bars in concrete was investigated. The process of chlorides bonding with aluminates yielding monochloride aluminate is monitored by XRD analyses. It was found that the amount of chlorides bonding with aluminates increases with an increase of temperature, and as a result, reduces the amount of 'free' chlorides in concrete. Potentiodynamic measurements have shown that increase in temperature of the heat treatment of working electrodes by chlorides leads to a reduction of steel bars corrosion as a result of either the increase of the monochloride-aluminate content or the decrease of free chlorides amount. Chlorides bound in chloroaluminate hydrates do not cause activation of steel bars corrosion in concrete. It was also proven that the increase of free chlorides concentration in the concrete leads to intensification of steel bars corrosion. This additionally approves that free chlorides are only the activators of process of steel bars corrosion in the concrete.

  19. 21 CFR 878.4015 - Wound dressing with poly (diallyl dimethyl ammonium chloride) (pDADMAC) additive.

    Science.gov (United States)

    2010-04-01

    ... ammonium chloride) (pDADMAC) additive. 878.4015 Section 878.4015 Food and Drugs FOOD AND DRUG... DEVICES Surgical Devices § 878.4015 Wound dressing with poly (diallyl dimethyl ammonium chloride) (pDADMAC... Dressing With Poly (Diallyl Dimethyl Ammonium Chloride) (pDADMAC) Additive.” See § 878.1(e)...

  20. 40 CFR 721.10056 - Benzenemethanaminium, N-(3-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides.

    Science.gov (United States)

    2010-07-01

    ...)-N,N-dimethyl-, N-soya acyl derivs., chlorides. 721.10056 Section 721.10056 Protection of Environment...-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides. (a) Chemical substance and significant new uses...-dimethyl-, N-soya acyl derivs., chlorides (PMN P-03-47; CAS No. 90194-13-1) is subject to reporting...

  1. 21 CFR 700.14 - Use of vinyl chloride as an ingredient, including propellant of cosmetic aerosol products.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Use of vinyl chloride as an ingredient, including... Products § 700.14 Use of vinyl chloride as an ingredient, including propellant of cosmetic aerosol products. (a) Vinyl chloride has been used as an ingredient in cosmetic aerosol products including hair...

  2. 76 FR 76766 - Standard on Vinyl Chloride; Extension of the Office of Management and Budget's (OMB) Approval of...

    Science.gov (United States)

    2011-12-08

    .... OSHA-2011-0196] Standard on Vinyl Chloride; Extension of the Office of Management and Budget's (OMB... collection requirements specified in the Standard on Vinyl Chloride (29 CFR 1910.1017). DATES: Comments must... brief description of the collection of information requirements contained in the Vinyl Chloride...

  3. Halogen-bonding for visual chloride ion sensing: a case study using supramolecular poly(aryl ether) dendritic organogel systems.

    Science.gov (United States)

    Liu, Zhi-Xiong; Sun, Yihua; Feng, Yu; Chen, Hui; He, Yan-Mei; Fan, Qing-Hua

    2016-02-07

    A convenient and straightforward method for the visual recognition of chloride ion has been established through a chloride-responsive dendritic organogel. The specificity was largely attributed to the higher binding affinity of the dendritic gelator for chloride compared with other anions through halogen bonding interactions.

  4. The action and interaction of calcium and alkali chlorides on eggs of Limnaea stagnalis and their chemical interpretation

    NARCIS (Netherlands)

    Geilenkirchen, W.L.M.

    1964-01-01

    1. 1. The action and interaction of CaCl2 and alkali chlorides on eggs of Limnaea stagnalis have been studied. 2. 2. CaCl2 antagonizes death caused by alkali chlorides. The number of normally developing embryos increases in all cases. 3. 3. Alkali chlorides antagonize death caused by CaCl2. With NaC

  5. Durability of reinforced adobe exposed to chloride ions

    Directory of Open Access Journals (Sweden)

    Giménez, A.

    2006-12-01

    Full Text Available One of the primary shortcomings of adobe, a dried mudblock stabilized with sisal hemp and cement widely used across all of Latin America, is its dimensional instability when exposed to water or aggressive environments. The present paper evaluates the electrochemical performance of reinforced adobe block after 1,000 days of exposure to a simulated marine environment. The specimens used were adobe blocks internally reinforced with 3/8-inch steel bars. The specimens were watered every two weeks: one group with potable water to simulate a natural urban environment and the other with a 3% sodium chloride solution to simulate a marine environment.Chloride penetration in powder extracted from the specimens was determined using the Mohr method. Electrochemical measurements included Gecor 6 electric potential(Eº and corrosion intensity (icorr readings. The final conclusion drawn from an analysis of the results was that in all cases the amount of free chlorides present sufficed to depassivate reinforcing steel and that the system component providing the most effective protection was the rough casting mortar. Consequently, this type of adobe mixes is not recommended for use in marine or industrial environments.La tierra-cemento-sisal es un material cuyo uso se encuentra muy difundido en toda Latinoamérica, entre sus principales limitaciones está la inestabilidad volumétrica ante el agua y ambientes agresivos. Por tal motivo, en este trabajo se evaluó el comportamiento electroquímico de bloques de tierra-cemento-sisal armado expuestos durante 1.000 días a un ambiente marino simulado. Las probetas utilizadas fueron bloques de tierra-cemento-sisal incorporándole internamente barras de acero de 3/8 de pulg. Las probetas se sometieron a un rociado quincenal: las de ambiente natural urbano con agua potable y las de ambiente marino simulado con una solución al 3% de cloruro de sodio. La penetración de cloruros se determinó extrayendo polvillo y

  6. Activation of AMPK inhibits cholera toxin stimulated chloride secretion in human and murine intestine.

    Directory of Open Access Journals (Sweden)

    Ailín C Rogers

    Full Text Available Increased intestinal chloride secretion through chloride channels, such as the cystic fibrosis transmembrane conductance regulator (CFTR, is one of the major molecular mechanisms underlying enterotoxigenic diarrhea. It has been demonstrated in the past that the intracellular energy sensing kinase, the AMP-activated protein kinase (AMPK, can inhibit CFTR opening. We hypothesized that pharmacological activation of AMPK can abrogate the increased chloride flux through CFTR occurring during cholera toxin (CTX mediated diarrhea. Chloride efflux was measured in isolated rat colonic crypts using real-time fluorescence imaging. AICAR and metformin were used to activate AMPK in the presence of the secretagogues CTX or forskolin (FSK. In order to substantiate our findings on the whole tissue level, short-circuit current (SCC was monitored in human and murine colonic mucosa using Ussing chambers. Furthermore, fluid accumulation was measured in excised intestinal loops. CTX and forskolin (FSK significantly increased chloride efflux in isolated colonic crypts. The increase in chloride efflux could be offset by using the AMPK activators AICAR and metformin. In human and mouse mucosal sheets, CTX and FSK increased SCC. AICAR and metformin inhibited the secretagogue induced rise in SCC, thereby confirming the findings made in isolated crypts. Moreover, AICAR decreased CTX stimulated fluid accumulation in excised intestinal segments. The present study suggests that pharmacological activation of AMPK effectively reduces CTX mediated increases in intestinal chloride secretion, which is a key factor for intestinal water accumulation. AMPK activators may therefore represent a supplemental treatment strategy for acute diarrheal illness.

  7. Salt equivalence and temporal dominance of sensations of different sodium chloride substitutes in butter.

    Science.gov (United States)

    de Souza, Vanessa Rios; Freire, Tassyana Vieira Marques; Saraiva, Carla Gonçalves; de Deus Souza Carneiro, João; Pinheiro, Ana Carla Marques; Nunes, Cleiton Antônio

    2013-08-01

    Studies indicate a positive association between dietary salt intake and some diseases, which has promoted the tendency to reduce the sodium in foods. The objective of this study was to determine the equivalent amount of different sodium chloride replacements required to promote the same degree of ideal saltiness in butter and to study the sensory profile of sodium chloride and the substitutes using the analysis of Temporal Dominance of Sensations (TDS). Using the magnitude estimation method, it was determined that the potencies of potassium chloride, monosodium glutamate and potassium phosphate relative to the 1% sodium chloride in butter are 83·33, 31·59 and 33·32, respectively. Regarding the sensory profile of the tested salt substitutes, a bitter taste was perceived in the butter with potassium chloride, a sour taste was perceived in the butter with potassium phosphate and sweet and umami tastes were dominant in the butter with monosodium glutamate. Of all the salt substitutes tested calcium lactate, potassium lactate, calcium chloride and magnesium chloride were impractical to use in butter.

  8. Impact of the associated cation on chloride binding of Portland cement paste

    Energy Technology Data Exchange (ETDEWEB)

    De Weerdt, K., E-mail: klaartje.d.weerdt@ntnu.no [Department of Structural Engineering, Norwegian University of Science and Technology (Norway); Department of Engineering and Applied Sciences, University of Bergamo (Italy); Colombo, A. [Department of Structural Engineering, Norwegian University of Science and Technology (Norway); Department of Engineering and Applied Sciences, University of Bergamo (Italy); Coppola, L. [Department of Engineering and Applied Sciences, University of Bergamo (Italy); Justnes, H. [SINTEF Building and Infrastructure, Trondheim (Norway); Geiker, M.R. [Department of Structural Engineering, Norwegian University of Science and Technology (Norway)

    2015-02-15

    Well hydrated cement paste was exposed to MgCl{sub 2}, CaCl{sub 2} and NaCl solutions at 20 °C. The chloride binding isotherms for free chloride concentrations ranging up to 1.5 mol/l were determined experimentally. More chlorides were found to be bound when the associated cation was Mg{sup 2} {sup +} or Ca{sup 2} {sup +} compared to Na{sup +}. The chloride binding capacity of the paste appeared to be related to the pH of the exposure solution. In order to explain the cation dependency of the chloride binding a selection of samples was investigated in detail using experimental techniques such as TG, XRD and SEM–EDS to identify the phases binding the chlorides. The experimentally obtained data were compared with the calculations of a thermodynamic model, GEMS. It was concluded that the measured change in chloride binding depending on the cation was mainly governed by the pH of the exposure solution and thereby the binding capacity of the C-S-H.

  9. Chloride Ion Transmission Model under the Drying-wetting Cycles and Its Solution

    Institute of Scientific and Technical Information of China (English)

    HUANG Ying; WEI Jun; DONG Rongzhen; ZENG Hua

    2014-01-01

    The chloride ion transmission model considering diffusion and convection was established respectively for different zones in concrete by analyzing chloride ion transmission mechanism under the drying-wetting cycles. The finite difference method was adopted to solve the model. The equation of chloride ion transmission model in the convection and diffusion zone of concrete was discreted by the group explicit scheme with right single point (GER method) and the equation in diffusion zone was discreted by FTCS difference scheme. According to relative humidity characteristics in concrete under drying-wetting cycles, the seepage velocity equation was formulated based on Kelvin Equation and Darcy’s Law. The time-variant equations of chloride ion concentration of concrete surface and the boundary surface of the convection and diffusion zone were established. Based on the software MATLAB the numerical calculation was carried out by using the model and basic material parameters from the experiments. The calculation of chloride ion concentration distribution in concrete is in good agreement with the drying-wetting cycles experiments. It can be shown that the chloride ion transmission model and the seepage velocity equation are reasonable and practical. Studies have shown that the chloride ion transmission in concrete considering convection and diffusion under the drying-wetting cycles is the better correlation with the actual situation than that only considering the diffusion.

  10. Chloride is essential for contraction of afferent arterioles after agonists and potassium

    DEFF Research Database (Denmark)

    Jensen, B L; Ellekvist, Peter; Skøtt, O

    1997-01-01

    A depolarizing chloride efflux has been suggested to activate voltage-dependent calcium channels in renal afferent arteriolar smooth muscle cells in response to vasoconstrictors. To test this proposal, rabbit afferent arterioles were microperfused, and the contractile dose responses to norepineph......A depolarizing chloride efflux has been suggested to activate voltage-dependent calcium channels in renal afferent arteriolar smooth muscle cells in response to vasoconstrictors. To test this proposal, rabbit afferent arterioles were microperfused, and the contractile dose responses......). Reintroduction of chloride fully restored the sensitivity to norepinephrine. Contractions after ANG II and potassium were totally abolished in the absence of chloride (n = 6). In additional experiments (n = 7), the arteriolar contraction to 100 mM potassium was abolished only 1 min after removal of extracellular...... chloride. We conclude that norepinephrine and ANG II use different mechanisms for contraction and that extracellular chloride is essential for contraction in afferent arterioles after activation of voltage-dependent calcium channels. We suggest that a chloride influx pathway is activated concomitantly...

  11. The effect of mercury on chloride secretion in the shark (Squalus acanthias) rectal gland.

    Science.gov (United States)

    Silva, P; Epstein, F H; Solomon, R J

    1992-11-01

    1. Mercuric chloride inhibited chloride secretion in a dose dependent way in isolated perfused rectal glands. The effect was readily apparent at a concentration of 10(-6) M and profound and irreversible at 10(-4) M. 2. The dithiol dithiothreitol (DTT) 10(-2) M completely prevented the effect of 10(-6) M mercuric chloride, reduced that at 10(-5) M and 10(-4) M, and made the inhibition at the latter concentration reversible. 3. Two organic mercurials, mersalyl and meralluride, that are effective diuretics in the mammalian kidney, and p-chloromercuribenzoyl sulfonic acid (PCMBS), that has no diuretic activity, had no effect on chloride secretion by the rectal gland. 4. The effect of mersalyl was not modified by lowering the pH of the solution perfusing the glands. 5. These results indicate that inorganic mercury and organic mercurials do not share the same mechanism of action. 6. The absence of an effect of organic mercurials on chloride transport in the rectal gland suggests that its effect on another chloride transporting epithelia, the thick ascending limb of the loop of Henle, is not mediated by inhibition of the chloride cotransporter or Na+, K(+)-ATPase, common to both epithelia.

  12. The impact of sulphate and magnesium on chloride binding in Portland cement paste

    Energy Technology Data Exchange (ETDEWEB)

    De Weerdt, K., E-mail: klaartje.d.weerdt@ntnu.no [Department of Structural Engineering, Norwegian University of science and Technology, Trondheim (Norway); SINTEF Building and Infrastructure, Trondheim (Norway); Orsáková, D. [Department of Civil Engineering, Technical University of Brno, Brno (Czech Republic); Geiker, M.R. [Department of Structural Engineering, Norwegian University of science and Technology, Trondheim (Norway)

    2014-11-15

    The effect of magnesium and sulphate present in sea water on chloride binding in Portland cement paste was investigated. Ground well hydrated cement paste was exposed to MgCl{sub 2}, NaCl, NaCl + MgCl{sub 2}, MgSO{sub 4} + MgCl{sub 2} and artificial sea water solutions with a range of concentrations at 20 °C. Chloride binding isotherms are determined and pH of the solutions were measured. A selection of samples was examined by SEM-EDS to identify phase changes upon exposure. The experimental data were compared with calculations of a thermodynamic model. Chloride binding from sea water was similar to chloride binding for NaCl solutions. The magnesium content in the sea water lead to a slight decrease in pH, but this did not result in a notable increase in chloride binding. The sulphate present in sea water reduces both chloride binding in C–S–H and AFm phases, as the C–S–H incorporates more sulphates instead of chlorides, and part of the AFm phases converts to ettringite.

  13. Fatal exposure to methylene chloride among bathtub refinishers - United States, 2000-2011.

    Science.gov (United States)

    2012-02-24

    In 2010, the Michigan Fatality Assessment and Control Evaluation program conducted an investigation into the death of a bathtub refinisher who used a methylene chloride-based paint stripping product marketed for use in aircraft maintenance. The program identified two earlier, similar deaths in Michigan. Program staff members notified CDC's National Institute for Occupational Safety and Health (NIOSH), which in turn notified the Occupational Safety and Health Administration (OSHA). In addition to the three deaths, OSHA identified 10 other bathtub refinisher fatalities associated with methylene chloride stripping agents that had been investigated in nine states during 2000-2011. Each death occurred in a residential bathroom with inadequate ventilation. Protective equipment, including a respirator, either was not used or was inadequate to protect against methylene chloride vapor, which has been recognized as potentially fatal to furniture strippers and factory workers but has not been reported previously as a cause of death among bathtub refinishers. Worker safety agencies, public health agencies, methylene chloride-based stripper manufacturers, and trade organizations should communicate the extreme hazards of using methylene chloride-based stripping products in bathtub refinishing to employers, workers, and consumers. Employers should strongly consider alternative methods of bathtub stripping and always ensure worker safety protections that reduce the risk for health hazards to acceptable levels. Employers choosing to use methylene chloride-based stripping products must comply with OSHA's standard to limit methylene chloride exposures to safe levels.

  14. Diffusion Decay Coefficient for Chloride Ions of Concrete Containing Mineral Admixtures

    Directory of Open Access Journals (Sweden)

    Jae-Im Park

    2016-01-01

    Full Text Available The diffusion coefficient for chloride ions and the diffusion decay coefficient for chloride ions are essential variables for a service life evaluation of concrete structures. They are influenced by water-binder ratio, exposure condition, curing temperature, cement type, and the type and use of mineral admixture. Mineral admixtures such as ground granulated blast furnace slag, fly ash, and silica fume have been increasingly used to improve resistance against chloride ions penetration in concrete structures built in an offshore environment. However, there is not enough measured data to identify the statistical properties of diffusion decay coefficient for chloride ions in concrete using mineral admixtures. This paper is aimed at evaluating the diffusion decay coefficient for chloride ions of concrete using ordinary Portland cement or blended cement. NT BUILD 492 method, an electrophoresis experiment, was used to measure the diffusion coefficient for chloride ions with ages. It was revealed from the test results that the diffusion decay coefficient for chloride ions was significantly influenced by W/B and the replacement ratio of mineral admixtures.

  15. Egg Production and Quality of Quails Fed Diets with Varying Levels of Methionine and Choline Chloride

    Directory of Open Access Journals (Sweden)

    Khairani

    2016-04-01

    Full Text Available The aim of the present study was to determine the effect of choline chloride supplementation at 1500 ppm in diets containing various levels of methionine on egg production and egg quality in quails. A total of 180 birds, at 6 week-old quail were divided into 18 experimental units, and assigned to a 2 x 3 factorial design experiment with 3 replications (10 birds each in each treatment. The birds were offered diets containing choline chloride at either 0 (A1 or 1500 ppm (A2, with three levels of methionine namely, low (0.19%, B1, standard (0.79%, B2 and, high (1.05%, B3. The feeding trial lasted for 8 weeks. Supplementation of choline chloride in low methionine diet significantly (P<0.05 increased egg production, egg mass, and egg weight as compared to those without choline chloride supplementation. Supplementation of choline chloride significantly (P<0.05 increased egg yolk weight but decreased albumen and egg shell weight as compared to those fed diets without choline chloride supplementation. It can be concluded that supplementation of choline chloride to a diet containing low methionine increased egg production, without affecting egg quality.

  16. Molten Chloride Salts for Heat Transfer in Nuclear Systems

    Science.gov (United States)

    Ambrosek, James Wallace

    2011-12-01

    A forced convection loop was designed and constructed to examine the thermal-hydraulic performance of molten KCl-MgCl2 (68-32 at %) salt for use in nuclear co-generation facilities. As part of this research, methods for prediction of the thermo-physical properties of salt mixtures for selection of the coolant salt were studied. In addition, corrosion studies of 10 different alloys were exposed to the KCl-MgCl2 to determine a suitable construction material for the loop. Using experimental data found in literature for unary and binary salt systems, models were found, or developed to extrapolate the available experimental data to unstudied salt systems. These property models were then used to investigate the thermo-physical properties of the LINO3-NaNO3-KNO 3-Ca(NO3), system used in solar energy applications. Using these models, the density, viscosity, adiabatic compressibility, thermal conductivity, heat capacity, and melting temperatures of higher order systems can be approximated. These models may be applied to other molten salt systems. Coupons of 10 different alloys were exposed to the chloride salt for 100 hours at 850°C was undertaken to help determine with which alloy to construct the loop. Of the alloys exposed, Haynes 230 had the least amount of weight loss per area. Nickel and Hastelloy N performed best based on maximum depth of attack. Inconel 625 and 718 had a nearly uniform depletion of Cr from the surface of the sample. All other alloys tested had depletion of Cr along the grain boundaries. The Nb in Inconel 625 and 718 changed the way the Cr is depleted in these alloys. Grain-boundary engineering (GBE) of Incoloy 800H improved the corrosion resistance (weight loss and maximum depth of attack) by nearly 50% as compared to the as-received Incoloy 800H sample. A high temperature pump, thermal flow meter, and pressure differential device was designed, constructed and tested for use in the loop, The heat transfer of the molten chloride salt was found to

  17. Passivity of Metals in the Point Defect Model: Effect of Chloride [Part-III

    OpenAIRE

    Emmanuel, Bosco

    2012-01-01

    In this paper we study the effect of addition of chloride on the stability of the compact oxide layer pre-existing on a metal surface at a given impressed potential and . The variant of the point defect model (PDM)advanced by us recently is used to construct a theory for the chloride-induced build-up of metal vacancies at the metal-film interface and the chloride-induced dissolution of the compact oxide layer. Under the quasi-steady-state approximation the relevant moving boundary value probl...

  18. Practical analysis of high purity chemicals--V. Precision silver chloride gravimetry.

    Science.gov (United States)

    Little, K

    1971-09-01

    A reasonably simple gravimetric silver chloride procedure with fairly wide tolerance in conditions is presented in full detail with all critical steps and precautions delineated. The procedure allows the precision determination of chloride by analysts having limited expertise with exacting gravimetric methods, and can be performed with equipment common to nearly all laboratories and without dependence on a standard substance. The elapsed and actual working times for the assessment of a solid sample in triplicate are 65 and 10-12 hr respectively. The application of the procedure to the assay of some high-purity chloride salts and to the standardization of hydrochloric acid solutions is described.

  19. Stress Corrosion Cracking of an Austenitic Stainless Steel in Nitrite-Containing Chloride Solutions

    Directory of Open Access Journals (Sweden)

    R. K. Singh Raman

    2014-12-01

    Full Text Available This article describes the susceptibility of 316L stainless steel to stress corrosion cracking (SCC in a nitrite-containing chloride solution. Slow strain rate testing (SSRT in 30 wt. % MgCl2 solution established SCC susceptibility, as evidenced by post-SSRT fractography. Addition of nitrite to the chloride solution, which is reported to have inhibitive influence on corrosion of stainless steels, was found to increase SCC susceptibility. The susceptibility was also found to increase with nitrite concentration. This behaviour is explained on the basis of the passivation and pitting characteristics of 316L steel in chloride solution.

  20. Studies on poly (vinyl chloride/silica dioxide composite hollow fiber membrane

    Directory of Open Access Journals (Sweden)

    Mei Shuo

    2016-01-01

    Full Text Available Poly (vinyl chloride/silica dioxide composite hollow fiber membranes were prepared by using the method of immersion-precipitation process. The influences of stretching ratio on the formation of the interfacial microporous of poly (vinyl chloride/silica dioxide composite hollow fiber membranes were specifically investigated by scanning electron microscope, dynamic mechanical analysis, and finite element method. Results show that with the stretching ratio increasing, numerous IFM appear on the surface of membranes. Finite element method actually reflects the dynamic change of microporous structure of poly (vinyl chloride/silica dioxide composite hollow fiber membranes.

  1. Analgesic effect of intrathecal bumetanide is accompanied by changes in spinal sodium-potassium-chloride co-transporter 1 and potassium-chloride co-transporter 2 expression in a rat model of incisional pain

    Institute of Scientific and Technical Information of China (English)

    Yanbing He; Shiyuan Xu; Junjie Huang; Qingjuan Gong

    2014-01-01

    Accumulating evidence has demonstrated that the sodium-potassium-chloride co-transporter 1 and potassium-chloride co-transporter 2 have a role in the modulation of pain transmission at the spinal level through chloride regulation in the pain pathway and by effecting neuronal excitability and pain sensitization. The present study aimed to investigate the analgesic effect of the speciifc sodium-potassium-chloride co-transporter 1 inhibitor bumetanide, and the change in spinal sodium-potassium-chloride co-transporter 1 and potassium-chloride co-transporter 2 expression in a rat model of incisional pain. Results showed that intrathecal bumetanide could decrease cumulative pain scores, and could increase thermal and mechanical pain thresholds in a rat model of incisional pain. Sodium-potassium-chloride co-transporter 1 expression in-creased in neurons from dorsal root ganglion and the deep laminae of the ipsilateral dorsal horn following incision. By contrast, potassium-chloride co-transporter 2 expression decreased in neurons of the deep laminae from the ipsilateral dorsal horn. These ifndings suggest that spinal sodium-potassium-chloride co-transporter 1 expression was up-regulated and spinal potassi-um-chloride co-transporter 2 expression was down-regulated following incision. Intrathecal bumetanide has analgesic effects on incisional pain through inhibition of sodium-potassi-um-chloride co-transporter 1.

  2. Safety considerations of lithium-thionyl chloride cells

    Science.gov (United States)

    Subbarao, Surampudi; Halpert, Gerald; Stein, Irving

    1986-06-01

    The use of spirally wound lithium-thionyl chloride (Li-SOCl2) cells is currently limited because of their hazardous behavior. Safety hazards have ranged from mild venting of toxic materials to violent explosions and fires. These incidents may be related to both user- and manufacturer-induced causes. Many explanations have been offered to explain the unsafe behavior of the cells under operating and abuse conditions. Explanations fall into two categories: (1) thermal mechanisms, and (2) chemical mechanisms. However, it is quite difficult to separate the two. Both may be responsible for cell venting or explosion. Some safety problems encountered with these cells also may be due to design deficiencies and ineffective quality control during cell fabrication. A well-coordinated basic and applied research program is needed to develop safe Li-SOCl2 cells. Recommendations include: (1) learnig more about Li-SOL2 cell chemistry; (2) modeling cell and battery behavior; (3) optimizing cell design for safety and performance, (4) implementing quality control procedures; and (5) educating users.

  3. The faradaic efficiency of the lithium-thionyl chloride battery

    Energy Technology Data Exchange (ETDEWEB)

    Hoier, S.N.; Eisenmann, E.T. [Sandia National Labs., Albuquerque, NM (United States). Battery Research Dept.

    1996-04-01

    The efficiency of converting chemical energy into electrical energy has been studied for the case of D-size, low and medium rate lithium-thionyl chloride (Li/TC) cells, under DC and various pulsed loads. Microcalorimetric monitoring of the heat output during discharge allowed the direct measurement of the faradaic efficiency, and showed that self-discharge is far more pervasive than previously acknowledged by researchers and battery manufacturers. Evaluations of the cell dynamics prove that current load and temperature fluctuations combine to disrupt the lithium passivation and to greatly enhance self-discharge. Typical faradaic efficiencies for DC range from abut 30% at low current density to 90% at moderate and 75% at high current density. Pulsed current further depresses these efficiency levels, except at very low average current densities. The decreased faradaic efficiency of Li/TC batteries in certain pulse situations needs to be studied further to define the range of applications for which it can be successfully used.

  4. Self-assembled hemocompatible coating on poly (vinyl chloride) surface

    Energy Technology Data Exchange (ETDEWEB)

    Zha Zhengbao; Ma Yan; Yue Xiuli; Liu Meng [Nanobiotechnology Division, State Key Laboratory of Urban Water Resources and Environment, School of Sciences, Harbin Institute of Technology, Harbin 150001 (China); Dai Zhifei, E-mail: zhifei.dai@hit.edu.cn [Nanobiotechnology Division, State Key Laboratory of Urban Water Resources and Environment, School of Sciences, Harbin Institute of Technology, Harbin 150001 (China)

    2009-11-15

    A stable hemocompatible coating was fabricated by consecutive alternating adsorption of iron (III) and two kinds of polysaccharides, heparin (Hep) and dextran sulfate (DS), onto poly (vinyl chloride) (PVC) surfaces via electrostatic interaction. The fluctuation of contact angles with the alternative deposition of iron (III) and polysaccharides verified the progressive buildup of the mulitilayer coating onto the PVC surface. Atomic force microscopy (AFM) analysis revealed that the PVC surfaces were completely masked by iron-polysaccharides multilayer coatings. The activated partial thromboplastin time (APTT) assay showed that both Hep/Fe{sup 3+}/Hep and DS/Fe{sup 3+}/Hep coated PVC were less thrombogenic than the uncoated one. Chromogenic assay for heparin activity proved definitively that the inhibition of locally produced thrombin was ascribed to the thromboresistance of the surface-bound heparin. Compared with the unmodified PVC surfaces, iron-polysaccharide multilayer coating presented a drastically reduced adhesion in vitro of platelets, polymorphonuclear neutrophil leukocytes (PMN) and peripheral blood mononuclear cells (PBMC). Interestingly, the DS/Fe{sup 3+}/Hep coating was found to exhibit higher hydrophilicity and stability, hence lower non-specific protein adsorption in comparison with Hep/Fe{sup 3+}/Hep coating due to the incorporation of dextran sulfate into the multilayer coating.

  5. Kinetics of Thermal Degradation of Recycled Polyvinyl Chloride Resin

    Directory of Open Access Journals (Sweden)

    I. M. Alwaan

    2014-01-01

    Full Text Available The goal of this study is to find the effect of time and temperature on the thermal degradation of recycled polyvinyl chloride (PVC resin. The isothermal rate of reaction (r of recycled PVC resin was investigated at the following temperatures to: 100, 110, 120, 130, and 140°C at period of times ranging from 10 to 50 min. The result shows that the rate of reaction (r of recycled PVC increases with increasing temperatures. The reaction rate constant (K for temperatures ranging from 100 to 140°C was doubled from 0.028–0.056 mol·L−1·S−1. The process was found to be zero order reaction at all range of temperatures 100–140°C. The activation energy of the thermal weight loss was calculated at different temperatures (E/R = 2739.5°K. The average enthalpy and entropy of reaction at temperature of 298°K were determined.

  6. Hypokalemia as an early index in trimethyltin chloride poisoning

    Institute of Scientific and Technical Information of China (English)

    TangXJ; LiLY

    2002-01-01

    Nowdays,dimethyltin(DMT) is widely used as plastic stabilizers.Trimethyltin chloride(TMT) is the main byproduct of DMT.Our study on SD rats had shown that hypokalemia played a very inportant role in TMT poisoning.The purpose of this paper was to clarify if hypokalemia can be used as an early index of diagnosis,therapy and prevention in TMT intoxication.We analyzed the serum potassium of 169 cases exposed to TMT,from which 123 cases were measured in 24h after the disease was complained.The serum potassium of 96 cases(78%) were below 3.5mmol·L-1.Four cases died with very serious hypokalemia(<2.5mmol·L-1).The lower the serum potassium was,the more serious of symptom would be found.In the recent 3 accidents,we measured the serum potassium as early as possible,and treat with KCl(iv or po) rightly.All of the 95 cases recovered within 1 month.No sequela was found.The available evidence suggested that hypokalemia could be the early clinical signs of TMT intoxication.Injection of KCl early should be the first selected treatment.

  7. Benzalkonium Chloride Induced Bronchoconstriction in Patients with Stable Bronchial Asthma

    Science.gov (United States)

    Lee, Byoung Hoon

    2007-01-01

    Background Although benzalkonium chloride (BAC)-induced bronchoconstriction occurs in patients with bronchial asthma, BAC-containing nebulizer solutions are still being used in daily practice in Korea. The aim of this study was to evaluate the effects of inhaled aqueous solutions containing BAC. Methods Thirty subjects with bronchial asthma and 10 normal controls inhaled up to three 600 µg nebulized doses of BAC using a jet nebulizer. FEV1 (forced expiratory volume at one second) was measured 15 minutes after each dose. Inhalations were repeated every 20 minutes until FEV1 decreased by 15% or more (defined as BAC-induced bronchoconstriction) or the 3 doses were administered. Results The percent fall in FEV1 in response to BAC inhalation was significantly higher in asthmatics than in normal subjects (p<0.05). BAC administration in subjects with asthma reached a plateau (maximal effect). BAC-induced bronchoconstriction was found in 6 asthmatics (20%), with two responders after the 2nd inhalation and after the 3rd inhalation. The percent fall in FEV1 in response to the 1st inhalation of BAC was significantly higher in asthmatics with higher bronchial hyperresponsiveness (BHR) than in those with lower BHR. Conclusions This study suggests that the available multi-dose nebulized solution is generally safe. However, significant bronchoconstriction can occur at a relatively low BAC dose in asthmatics with severe airway responsiveness. PMID:18309682

  8. Ocular toxicity of benzalkonium chloride homologs compared with their mixtures.

    Science.gov (United States)

    Okahara, Akihiko; Tanioka, Hidetoshi; Takada, Koichi; Kawazu, Kouichi

    2013-12-01

    This study was performed to assess the in vivo ocular toxicity of benzalkonium chloride (BAK) homologs compared with commercially available BAK (BAK mixture) and to assess the ocular toxicity of BAK homolog after repeated ocular application. Rabbit eyes were examined by ophthalmology and scanning electron microscopy (SEM) after 10 applications of BAK homologs with C12 (C12-BAK) and C14 (C14-BAK) alkyl chain lengths and a BAK mixture at concentrations of 0.001% (w/v), 0.003% (w/v), 0.005% (w/v), 0.01% (w/v) and 0.03% (w/v). The ocular toxicity of C12-BAK to rabbit eyes was examined by ophthalmology and histopathology after repeated ocular application for 39 weeks. In addition, the antimicrobial activities of C12-BAK and C14-BAK against A. niger, S. aureus and P. aeruginosa were assessed. Ocular toxicity of C12-BAK was less than those of the BAK mixture and C14-BAK. No ocular toxicity was noted after ocular application of 0.01% C12-BAK to rabbits for 39 weeks. C12-BAK showed antimicrobial activities at a concentration of 0.003%. These results suggest that the use of C12-BAK to replace BAK mixture as a preservative in ophthalmic solutions should be considered in order to reduce the incidence of the corneal epithelial cell injury induced clinically by BAK.

  9. Mechanism of resistance to benzalkonium chloride by Pseudomonas aeruginosa.

    Science.gov (United States)

    Sakagami, Y; Yokoyama, H; Nishimura, H; Ose, Y; Tashima, T

    1989-01-01

    The mechanisms of resistance of Pseudomonas aeruginosa to benzalkonium chloride (BC) were studied. The effluence of cell components was observed in susceptible P. aeruginosa by electron microscopy, but resistant P. aeruginosa seemed to be undamaged. No marked changes in cell surface potential between Escherichia coli NIHJC-2 and a spheroplast strain were found. The contents of phospholipids (PL) and fatty and neutral lipids (FNL) in the cell walls of resistant P. aeruginosa were higher than those in the cell walls of susceptible P. aeruginosa. The amounts of BC adsorbed to PL and FNL of cell walls of BC-resistant P. aeruginosa were lower than those for BC-susceptible P. aeruginosa. Fifteen species of cellular fatty acids were identified by capillary gas chromatography and gas chromatography-mass spectrometry. The ability of BC to permeate the cell wall was reduced because of the increase in cellular fatty acids. These results suggested that the resistance of P. aeruginosa to BC is mainly a result of increased in the contents of PL and FNL. In resistant P. aeruginosa, the decrease in the amount of BC adsorbed is likely to be the result of increases in the contents of PL and FNL. Images PMID:2506813

  10. The CIC-3 chloride channels in cardiovascular disease

    Institute of Scientific and Technical Information of China (English)

    Dayue Darrel DUAN

    2011-01-01

    CIC-3 is a member of the CIC voltage-gated chloride(Cl-) channel superfamily. Recent studies have demonstrated the abundant expression and pleiotropy of CIC-3 in cardiac atrial and ventricular myocytes, vascular smooth muscle cells, and endothelial cells.CIC-3 Cl- channels can be activated by increase in cell volume, direct stretch of β1-integrin through focal adhesion kinase and many active molecules or growth factors including angiotensin Ⅱ and endothelin-1-mediated signaling pathways, Ca2+/calmodulin-dependent protein kinase Ⅱ and reactive oxygen species. CIC-3 may function as a key component of the volume-regulated Cl- channels, a superoxide anion transport and/or NADPH oxidase interaction partner, and a regulator of many other transporters. CIC-3 has been implicated in the regulation of electrical activity, cell volume, proliferation, differentiation, migration, apoptosis and intracellular pH. This review will highlight the major findings and recent advances in the study of CIC-3 Cl- channels in the cardiovascular system and discuss their important roles in cardiac and vascular remodeling during hypertension, myocardial hypertrophy, ischemia/reperfusion, and heart failure.

  11. Chloride, bromide and iodide scintillators with europium doping

    Science.gov (United States)

    Zhuravleva, Mariya; Yang, Kan

    2014-08-26

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  12. Strontium-copper selenite-chlorides: Synthesis and structural investigation

    Science.gov (United States)

    Berdonosov, Peter S.; Olenev, Andrei V.; Dolgikh, Valery A.

    2009-09-01

    Two new complex selenite-chlorides of strontium and copper Sr 2Cu(SeO 3) 2Cl 2 (I) and SrCu 2(SeO 3) 2Cl 2 (II) were obtained and characterized by X-ray diffraction technique, DTA and IR spectroscopy. Both compounds crystallize in the monoclinic system I: Sp. gr. P2 1/ n, a=5.22996(3) Å, b=6.50528(4) Å, c=12.34518(7) Å, β=91.3643(2)°, Z=2; II: Sp. gr. P2 1, a=7.1630(14) Å, b=7.2070(14) Å, c=8.0430(16) Å, β=95.92(3)°, Z=2. Comparison of the crystal structure of (I) with the structures of Sr 2M(SeO 3) 2Cl 2 ( M=Co, Ni) was performed. The substitution of strontium atom in the structure of (I) by Cu 2+ ion with a 3 d9 Jahn-Teller distorted surrounding leads to the lowering of the structure symmetry and to the appearance of the noncentrosymmetric structure of (II). The noncentrosymmetric character of the structure of (II) was confirmed by SHG signal (1.2 units relative to an α-quartz powder sample).

  13. Statistical testing and distribution for lead chloride toxicity

    Institute of Scientific and Technical Information of China (English)

    John H. Lange

    2005-01-01

    @@ Dear Sir, Graca et al. [1] provided an interesting investigation on the toxicity of lead chloride and sperm development in mice. However, I would like to make a comment on the statistical analysis presented. Table 1 and its results suggest that a comparison of treated (experiment) and control mice were undertaken using the t-test. The authors indicate that they used the t-test along with complementation of ANOVA analysis. It appears that the t-test was used for analysis in Table 1 and ANOVA, as indicated,for Table 2. Use of t-test for comparing three of more groups is not appropriate since this may result in a multiple comparison problem (increasing the type I error rate)[2, 3]. Multiple comparisons can result in the reporting of a P value that is significant (or of lower value) when in actuality it is not. It is better to use, for example, a one-way ANOVA followed by a post-test (post-hoc)which can take into account all comparisons. Other statistical testing can also be employed to control the overall type I error, such as Tukey-HSD (honest significant difference), Scheffe's and Bonferroni-Dunn methods [2].

  14. Preparation of polymeric aluminium ferric chloride from bauxite tailings

    Directory of Open Access Journals (Sweden)

    Ma D.

    2013-01-01

    Full Text Available Bauxite tailings are the main solid wastes in the ore dressing process. The Al2O3 and Fe2O3 contents in bauxite tailings can reach 50% and 13% respectively. The present study proposed a feasible method to use bauxite tailings to prepare polymeric aluminium ferric chloride (PAFC, a new composite inorganic polymer for water purification. Bauxite tailings roasted reacting with hydrochloric acid under air, pickle liquor which mainly contains Fe3+, Al3+ was generated, then calcium aluminate was used to adjust pH value and the basicity of the pickle liquor, the PAFC was subsequently prepared after the polymerization process. The optimal synthesizing parameters for the preparation of PAFC obtained were as follows: the concentration of hydrochloric acid of 24 wt%, ratio of hydrochloric acid to bauxite tailings of 6:1, temperature of 90ºC, leaching time of 2.5 hours, ration of pickle liquor to calcium aluminate of 12:1, polymerization temperature of 90ºC and polymerization time of about 3 hours. The basicity of PAFC was higher than 68%, the sum concentration of Al2O3 and Fe2O3 was beyond 12.5%. The results of flocculation tests indicate that the PAFC has a better performance of removing the turbidity of wastewater compared to PAC, and PAFC prepared by bauxite tailings is a kind of high quality flocculants.

  15. Exfoliation of Hexagonal Boron Nitride via Ferric Chloride Intercalation

    Science.gov (United States)

    Hung, Ching-cheh; Hurst, Janet; Santiago, Diana; Rogers, Richard B.

    2014-01-01

    Sodium fluoride (NaF) was used as an activation agent to successfully intercalate ferric chloride (FeCl3) into hexagonal boron nitride (hBN). This reaction caused the hBN mass to increase by approx.100 percent, the lattice parameter c to decrease from 6.6585 to between 6.6565 and 6.6569 ?, the x-ray diffraction (XRD) (002) peak to widen from 0.01deg to 0.05deg of the full width half maximum value, the Fourier transform infrared (FTIR) spectrum's broad band (1277/cm peak) to change shape, and new FTIR bands to emerge at 3700 to 2700 and 1600/cm. This indicates hBN's structural and chemical properties are significantly changed. The intercalated product was hygroscopic and interacted with moisture in the air to cause further structural and chemical changes (from XRD and FTIR). During a 24-h hold at room temperature in air with 100 percent relative humidity, the mass increased another 141 percent. The intercalated product, hydrated or not, can be heated to 750 C in air to cause exfoliation. Exfoliation becomes significant after two intercalation-air heating cycles, when 20-nm nanosheets are commonly found. Structural and chemical changes indicated by XRD and FTIR data were nearly reversed after the product was placed in hydrochloric acid (HCl), resulting in purified, exfoliated, thin hBN products.

  16. Application of cetylpyridinium chloride in dispersion of antibacterial ceramic glaze

    Institute of Scientific and Technical Information of China (English)

    CHAI Li-yuan; CHENG Ming-ming; PENG Bing; HUANG Yi; ZHANG Xiao-fei

    2006-01-01

    The adsorption of cetylpyridinium chloride(CPC) onto a ceramic glaze mixture composed of limestone, feldspar, quartz,kaolin, and antibacterial agent was studied. Both adsorption isothermals and the average particle zeta potential were investigated in order to understand the suspension stability as a function of pH, ionic strength, and surfactant concentration. The results show that under the optimal conditions such as pH value of 7 or 9, 0.01 mol/L of ionic strength and around critical micelle concentration(CMC)of surfactant, antibacterial ceramic glaze acquires fine dispersion stability. The adsorption of CPC on ceramic glaze particles is in accordance with Langmuir model in 0.01mol/L at pH=7 and pH=9. The adsorption of small amounts of cationic CPC onto the primarily negatively charged surfaces of the particles in the pH range of 7-9 produces strong attraction and flocculation due to hydrophobic interactions. High concentration of surfactant under 0.01 mol/L of salt provides high zeta potential, which produces a high stability.

  17. Multiscale modeling of the trihexyltetradecylphosphonium chloride ionic liquid.

    Science.gov (United States)

    Wang, Yong-Lei; Sarman, Sten; Li, Bin; Laaksonen, Aatto

    2015-09-14

    A multiscale modeling protocol was sketched for the trihexyltetradecylphosphonium chloride ([P6,6,6,14]Cl) ionic liquid (IL). The optimized molecular geometries of an isolated [P6,6,6,14] cation and a tightly bound [P6,6,6,14]Cl ion pair structure were obtained from quantum chemistry ab initio calculations. A cost-effective united-atom model was proposed for the [P6,6,6,14] cation based on the corresponding atomistic model. Atomistic and coarse-grained molecular dynamics simulations were performed over a wide temperature range to validate the proposed united-atom [P6,6,6,14] model against the available experimental data. Through a systemic analysis of volumetric quantities, microscopic structures, and transport properties of the bulk [P6,6,6,14]Cl IL under varied thermodynamic conditions, it was identified that the proposed united-atom [P6,6,6,14] cationic model could essentially capture the local intermolecular structures and the nonlocal experimental thermodynamics, including liquid density, volume expansivity and isothermal compressibility, and transport properties, such as zero-shear viscosity, of the bulk [P6,6,6,14]Cl IL within a wide temperature range.

  18. Evaluation of cetylpyridinium chloride for infection control in storage solution.

    Science.gov (United States)

    Ziskind, D; Gleitman, J; Rotstein, I; Friedman, M

    2003-05-01

    Storage solution is used in in vitro experimental studies to prevent dehydration of teeth collected immediately after extraction and to prevent bacterial and fungal growth in the storage media. The chemical nature of the storing agent may affect the tooth structure and material properties at the tested interface. The aim of this study was to evaluate the use of 0.1% cetylpyridinium chloride (CPC) as a new storage solution and to assess the possible effect of 0.1% thymol on microleakage and bond strength. Forty extracted human teeth were collected from 10 different dental clinics. Immediately after extraction, the teeth were randomly divided and immersed in four different storage solutions. Two test solutions of 0.1% CPC (group C) and 0.1% thymol (group T) were compared with phosphate-buffered saline (Group S - positive control) and to 3% H2O2 (group H - negative control). Bond strength test and dye penetration evaluation were then carried out. The findings suggest that the use of 0.1% CPC as storage solution does not affect bond strength to enamel. However, it may increase dye penetration at the cervical margin. The effect of 0.1% thymol on shear bond strength and dye penetration is similar to the effect of phosphate-buffered saline.

  19. Theoretical predictions of novel potassium chloride phases under pressure.

    Science.gov (United States)

    Shamp, Andrew; Saitta, Patrick; Zurek, Eva

    2015-05-14

    Evolutionary structure searches predict two hitherto unknown phases of KCl that are the most stable in the pressure regime of 200-600 GPa. I41/amd-KCl, which has the lowest enthalpy between ∼200-350 GPa, can be thought of as being composed of two three-connected nets. This structure can be compared with that of the Cs-IV electride (Cs(+)e(-)): the potassium ions assume the positions of the cesium ions, and the chloride ions are found roughly in the regions of the valence electrons. Above ∼350 GPa a Pnma phase, which is isotypic with phases of CsH and CsI that are stable under pressure, becomes preferred. Just as in Pnma-CsI, the atoms in Pnma-KCl assume an hcp-like lattice; these alkali halides resemble the high-pressure structures of the isoelectronic noble gas solids Xe and Ar, respectively. The equation of state of KCl is extended to 600 GPa, enabling the use of this alkali halide as a pressure guage in ultra-high pressure static compression experiments. KCl is predicted to remain insulating to at least 420 GPa.

  20. The salt (sodium chloride) requirements of growing bobwhite quail

    Science.gov (United States)

    Nestler, R.B.

    1949-01-01

    In the two experiments involving 452 bobwhite quail chicks, seven diets containing the following salt supplements, were compared: No additional salt; 0.25 per cent KaCl; 0.50 per cent NaC1; 0.75per cent NaCl; 1.00 per cent NaCl; 0.25 per cent Na2SO4; and 0.50 per cent KCl. All four diets containing sodium chloride gave about equal results in bird-growth, and produced better weights than the diet containing no additional salt. Survival was high on the 0.50, 0.75 and 1.00 per cent levels, especially the 0.75 per cent level. Feed consumption increased directly as the salt level of the diet was raised.....The results on the Na2SO4 and KCl while better than those on no saline supplementation, and somewhat inferior to those on NaCl, nevertheless are inconclusive because of inconsistency.