WorldWideScience

Sample records for calcium phosphate cements

  1. Calcium phosphate cements properties with polymers addition

    International Nuclear Information System (INIS)

    Calcium phosphate cements (CPC) have attracted great interest to use in orthopedics and dentistry as replacements for damaged parts of the skeletal system, showing good biocompatibility and osseointegration, allowing its use as bone graft. Several studies have shown that the addition of polymer additives have a strong influence on the cement properties. The low mechanical strength is the main obstacle to greater use of CPC as an implant material. The objective of this study was to evaluate properties of a cement based on α-tricalcium phosphate (α-TCP), added polymers. PVA (10%, 8%, 6%), sodium alginate (2%) and polyacrylate ammonia (3%), all in weight, were added to the synthesized α-TCP powder. The samples were molded and evaluated for density, porosity in vitro test (Simulated Body Fluid), crystalline phases and mechanical strength. The results show increased the mechanical properties of the cement when added these polymers

  2. Injectable bioactive calcium-magnesium phosphate cement for bone regeneration

    International Nuclear Information System (INIS)

    Novel injectable and degradable calcium-magnesium phosphate cement (CMPC) with rapid-setting characteristic was developed by the introduction of magnesium phosphate cement (MPC) into calcium phosphate cement (CPC). The calcium-magnesium phosphate cement prepared under the optimum P/L ratio exhibited good injectability and desired workability. It could set within 10 min at 37 0C in 100% relative humidity and the compressive strength could reach 47 MPa after setting for 48 h, indicating that the prepared cement has relatively high initial mechanical strength. The results of in vitro degradation experiments demonstrated the good degradability of the injectable CMPC, and its degradation rate occurred significantly faster than that of pure CPC in simulated body fluid (SBF) solution. It can be concluded that the novel injectable calcium-magnesium phosphate cement is highly promising for a wide variety of clinical applications, especially for the development of minimally invasive techniques.

  3. Evaluation of a porosity measurement method for wet calcium phosphate cements

    OpenAIRE

    Ajaxon, Ingrid; Maazouz, Yassine; Ginebra Molins, Maria Pau; Ohman, Caroline; Persson, Cecilia

    2015-01-01

    The porosity of a calcium phosphate cement is a key parameter as it affects several important properties of the cement. However, a successful, non-destructive porosity measurement method that does not include drying has not yet been reported for calcium phosphate cements. The aim of this study was to evaluate isopropanol solvent exchange as such a method. Two different types of calcium phosphate cements were used, one basic (hydroxyapatite) and one acidic (brushite). The cements were allowed ...

  4. Prediction of the Setting Properties of Calcium Phosphate Bone Cement

    Directory of Open Access Journals (Sweden)

    Seyed Mahmud Rabiee

    2012-01-01

    Full Text Available Setting properties of bone substitutes are improved using an injectable system. The injectable bone graft substitutes can be molded to the shape of the bone cavity and set in situ when injected. Such system is useful for surgical operation. The powder part of the injectable bone cement is included of β-tricalcium phosphate, calcium carbonate, and dicalcium phosphate and the liquid part contains poly ethylene glycol solution with different concentrations. In this way, prediction of the mechanical properties, setting times, and injectability helps to optimize the calcium phosphate bone cement properties. The objective of this study is development of three different adaptive neurofuzzy inference systems (ANFISs for estimation of compression strength, setting time, and injectability using the data generated based on experimental observations. The input parameters of models are polyethylene glycol percent and liquid/powder ratio. Comparison of the predicted values and measured data indicates that the ANFIS model has an acceptable performance to the estimation of calcium phosphate bone cement properties.

  5. Prediction of the setting properties of calcium phosphate bone cement.

    Science.gov (United States)

    Rabiee, Seyed Mahmud; Baseri, Hamid

    2012-01-01

    Setting properties of bone substitutes are improved using an injectable system. The injectable bone graft substitutes can be molded to the shape of the bone cavity and set in situ when injected. Such system is useful for surgical operation. The powder part of the injectable bone cement is included of β-tricalcium phosphate, calcium carbonate, and dicalcium phosphate and the liquid part contains poly ethylene glycol solution with different concentrations. In this way, prediction of the mechanical properties, setting times, and injectability helps to optimize the calcium phosphate bone cement properties. The objective of this study is development of three different adaptive neurofuzzy inference systems (ANFISs) for estimation of compression strength, setting time, and injectability using the data generated based on experimental observations. The input parameters of models are polyethylene glycol percent and liquid/powder ratio. Comparison of the predicted values and measured data indicates that the ANFIS model has an acceptable performance to the estimation of calcium phosphate bone cement properties. PMID:22919372

  6. On the development of an apatitic calcium phosphate bone cement

    Indian Academy of Sciences (India)

    Manoj Komath; H K Varma; R Sivakumar

    2000-04-01

    Development of an apatitic calcium phosphate bone cement is reported. 100 Particles of tetracalcium phosphate (TTCP) and dicalcium phosphate dihydrate (DCPD) were mixed in equimolar ratio to form the cement powder. The wetting medium used was distilled water with Na2HPO4 as accelerator to manipulate the setting time. The cement powder, on wetting with the medium, formed a workable putty. The setting times of the putty were measured using a Vicat type apparatus and the compressive strength was determined with a Universal Testing Machine. The nature of the precipitated cement was analyzed through X-ray diffraction (XRD), fourier transform infrared spectrometry (FTIR) and energy dispersive electron microprobe (EDAX). The results showed the phase to be apatitic with a calcium–to–phosphorous ratio close to that of hydroxyapatite. The microstructure analysis using scanning electron microscopy (SEM) showed hydroxyapatite nanocrystallite growth over particulate matrix surface. The structure has an apparent porosity of ∼ 52%. There were no appreciable dimensional or thermal changes during setting. The cement passed the in vitro toxicological screening (cytotoxicity and haemolysis) tests. Optimization of the cement was done by manipulating the accelerator concentration so that the setting time, hardening time and the compressive strength had clinically relevant values.

  7. Silver-Doped Calcium Phosphate Bone Cements with Antibacterial Properties

    Science.gov (United States)

    Rau, J. V.; Fosca, M.; Graziani, V.; Egorov, A. A.; Zobkov, Yu. V.; Fedotov, A. Yu.; Ortenzi, M.; Caminiti, R.; Baranchikov, A. E.; Komlev, V. S.

    2016-01-01

    Calcium phosphate bone cements (CPCs) with antibacterial properties are demanded for clinical applications. In this study, we demonstrated the use of a relatively simple processing route based on preparation of silver-doped CPCs (CPCs-Ag) through the preparation of solid dispersed active powder phase. Real-time monitoring of structural transformations and kinetics of several CPCs-Ag formulations (Ag = 0 wt %, 0.6 wt % and 1.0 wt %) was performed by the Energy Dispersive X-ray Diffraction technique. The partial conversion of β-tricalcium phosphate (TCP) phase into the dicalcium phosphate dihydrate (DCPD) took place in all the investigated cement systems. In the pristine cement powders, Ag in its metallic form was found, whereas for CPC-Ag 0.6 wt % and CPC-Ag 1.0 wt % cements, CaAg(PO3)3 was detected and Ag (met.) was no longer present. The CPC-Ag 0 wt % cement exhibited a compressive strength of 6.5 ± 1.0 MPa, whereas for the doped cements (CPC-Ag 0.6 wt % and CPC-Ag 1.0 wt %) the reduced values of the compressive strength 4.0 ± 1.0 and 1.5 ± 1.0 MPa, respectively, were detected. Silver-ion release from CPC-Ag 0.6 wt % and CPC-Ag 1.0 wt % cements, measured by the Atomic Emission Spectroscopy, corresponds to the average values of 25 µg/L and 43 µg/L, respectively, rising a plateau after 15 days. The results of the antibacterial test proved the inhibitory effect towards pathogenic Escherichia coli for both CPC-Ag 0.6 wt % and CPC-Ag 1.0 wt % cements, better performances being observed for the cement with a higher Ag-content. PMID:27096874

  8. Surgical Results of Lumbar Interbody Fusion Using Calcium Phosphate Cement

    OpenAIRE

    HIRASAWA, Motohiro; Mure, Hideo; Toi, Hiroyuki; Nagahiro, Shinji

    2014-01-01

    Clinical and radiological outcomes of lumbar interbody fusion using artificial fusion cages filled with calcium phosphate cements (CPCs) were retrospectively reviewed. Between 2002 and 2011, 25 patients underwent lumbar interbody fusion at Tokushima University Hospital, and 22 patients were enrolled in this study. Of these, 5 patients received autologous local bone grafts and 17 received CPC. Japan Orthopedic Association (JOA) score was used for clinical outcome assessments. Lumbar radiograph...

  9. Fabrications of zinc-releasing biocement combining zinc calcium phosphate to calcium phosphate cement.

    Science.gov (United States)

    Horiuchi, Shinya; Hiasa, Masahiro; Yasue, Akihiro; Sekine, Kazumitsu; Hamada, Kenichi; Asaoka, Kenzo; Tanaka, Eiji

    2014-01-01

    Recently, zinc-releasing bioceramics have been the focus of much attention owing to their bone-forming ability. Thus, some types of zinc-containing calcium phosphate (e.g., zinc-doped tricalcium phosphate and zinc-substituted hydroxyapatite) are examined and their osteoblastic cell responses determined. In this investigation, we studied the effects of zinc calcium phosphate (ZCP) derived from zinc phosphate incorporated into calcium phosphate cement (CPC) in terms of its setting reaction and MC3T3-E1 osteoblast-like cell responses. Compositional analysis by powder X-ray diffraction analysis revealed that HAP crystals were precipitated in the CPC containing 10 or 30wt% ZCP after successfully hardening. However, the crystal growth observed by scanning electron microscopy was delayed in the presence of additional ZCP. These findings indicate that the additional zinc inhibits crystal growth and the conversion of CPC to the HAP crystals. The proliferation of the cells and alkaline phosphatase (ALP) activity were enhanced when 10wt% ZCP was added to CPC. Taken together, ZCP added CPC at an appropriate fraction has a potent promotional effect on bone substitute biomaterials. PMID:24090874

  10. New developments in calcium phosphate bone cements: approaching spinal applications

    OpenAIRE

    Vlad, Maria Daniela

    2009-01-01

    La presente tesis doctoral (i.e., “New developments in calcium phosphate bone cements: approaching spinal applications”) aporta nuevos conocimientos en el campo de los cementos óseos de fosfato de calcio (CPBCs) en relación a su aplicación clínica en el campo de la cirugía vertebral mínimamente invasiva. La hipótesis central de esta investigación fue formulada en los siguientes términos: “Los cementos apatíticos pueden ser (si se optimizan) una alternativa mejor (debido a sus propiedades d...

  11. Augmentation of Pedicle Screw Fixation with Calcium Phosphate Cement

    Institute of Scientific and Technical Information of China (English)

    YANG Shu-hua; FU De-hao; LI Jin; XU Wei-hua; YANG Cao; YE Zhe-wei; ZUO Xiao-yan

    2004-01-01

    To determine whether a biodegradable calcium phosphate cement(CPC) provides significant augmentation of pedicle screw fixation or not,an in vitro biomechanical study was carried out to evaluate the biomechanical effect of CPC in the restoration and augmentation of pedicle screw fixation.Axial pullout test and cyclic bending resistance test were employed in the experiment,and polymethylmethacrylate (PMMA) was chosen as control.The results demonstrate that the pullout strengths following CPC restoration and augmentation are 74% greater on an average than those of the control group,but less than those of PMMA restoration group and augmentation group respectively (increased by 126% versus control).In cyclic bending resistance test,the CPC augmented screws are found to withstand a greater number of cycles or greater loading with less displacement before loosening,but the augmentation effect of PMMA is greater than that of CPC.

  12. Cytotoxicity, calcium release, and pH changes generated by novel calcium phosphate cement formulations.

    Science.gov (United States)

    Khashaba, Rania M; Lockwood, Petra E; Lewis, Jill B; Messer, Regina L; Chutkan, Norman B; Borke, James L

    2010-05-01

    Few published studies describe the biological properties of calcium phosphate cements (CPCs) for dental applications. We measured several biologically relevant properties of 3 CPCs over an extended (8 wk) interval. Monocalcium phosphate, calcium oxide, and synthetic hydroxyapatite were combined with either modified polyacrylic acid, light-activated modified polyalkenoic acid, or 35% w/w polymethyl vinyl ether maleic acid to obtain Types I, II, and III CPCs, respectively. Set cements were placed in direct contact with L929 fibroblasts for up to 8 weeks. Media Ca(+2) and pH were determined by atomic absorption spectroscopy and pH electrode respectively. Cell mitochondrial function was measured by MTT assay. Type I cements suppressed mitochondrial activity > 90% (vs. Teflon controls), but significantly (p 90% at all times. Type III cements elevated mitochondrial activity significantly after 7 wks. The pH profiles approached neutrality by 24 h, and all cements released calcium into the storage medium at all periods (24 h - 8 wk). We concluded that several types of cements had long-term biological profiles that show promise for dental applications. PMID:20235188

  13. The bactericidal and biocompatible characteristics of reinforced calcium phosphate cements

    International Nuclear Information System (INIS)

    Infection remains a serious medical problem in orthopaedic surgery. Antibiotic administration can be available either systemically via the blood stream or locally, directly into the infected bone. One of the main limitations of antibiotic administration is the development of multi-antibiotic-resistant bacterial strains. In this study, we developed bactericidal calcium phosphate cements (CPC) by incorporation of different molecular weight chitosan and hydroxypropyltrimethyl ammonium chloride chitosan (HACC). Two standard strains, S. epidermidis (ATCC35984) and S. aureus (ATCC25923), and one clinical isolate, methicillin-resistant S. epidermidis (MRSE), were selected to evaluate the antibacterial activity of these bone cements. Our data showed that the CPC loaded with low molecular weight chitosan and HACC significantly inhibited the bacterial adhesion and biofilm formation. In addition, HACC-containing CPC has no cytotoxic effects on both mouse pluripotent C3H10T1/2cell line and a murine L929 fibroblast cell line. We propose that HACC-containing CPC represents a promising polymer-based bactericidal bone scaffold in controlling orthopaedic surgery-related infection. (paper)

  14. Evaluation of a porosity measurement method for wet calcium phosphate cements.

    Science.gov (United States)

    Ajaxon, Ingrid; Maazouz, Yassine; Ginebra, Maria-Pau; Öhman, Caroline; Persson, Cecilia

    2015-11-01

    The porosity of a calcium phosphate cement is a key parameter as it affects several important properties of the cement. However, a successful, non-destructive porosity measurement method that does not include drying has not yet been reported for calcium phosphate cements. The aim of this study was to evaluate isopropanol solvent exchange as such a method. Two different types of calcium phosphate cements were used, one basic (hydroxyapatite) and one acidic (brushite). The cements were allowed to set in an aqueous environment and then immersed in isopropanol and stored under three different conditions: at room temperature, at room temperature under vacuum (300 mbar) or at 37℃. The specimen mass was monitored regularly. Solvent exchange took much longer time to reach steady state in hydroxyapatite cements compared to brushite cements, 350 and 18 h, respectively. Furthermore, the immersion affected the quasi-static compressive strength of the hydroxyapatite cements. However, the strength and phase composition of the brushite cements were not affected by isopropanol immersion, suggesting that isopropanol solvent exchange can be used for brushite calcium phosphate cements. The main advantages with this method are that it is non-destructive, fast, easy and the porosity can be evaluated while the cements remain wet, allowing for further analysis on the same specimen. PMID:26163278

  15. Polyelectrolyte addition effect on the properties of setting hydraulic cements based on calcium phosphate

    International Nuclear Information System (INIS)

    In the present work the effects of the addition of some poly electrolytes (sodium alginate and poly acrylic acid) on the solubility, crystalline phases, pH and mechanical strength under compression of three calcium phosphate cements were studied. (author)

  16. Balloon vetebroplasty with calcium phosphate cement augmentation for direct restoration of traumatic thoracolumbar vertebral fractures

    NARCIS (Netherlands)

    Verlaan, JJ; van Helden, WH; Oner, FC; Verbout, AJ; Dhert, WJA

    2002-01-01

    Study Design. A human cadaveric model was used to evaluate balloon vertebroplasty in traumatic vertebral fractures. Objectives. To assess the feasibility and safety of balloon vertebroplasty followed by calcium phosphate cement augmentation to prevent recurrent kyphosis. Summary of Background Data.

  17. Multiple characterization study on porosity and pore structure of calcium phosphate cements

    OpenAIRE

    Pastorino Carraz, David; Canal Barnils, Cristina; Ginebra Molins, Maria Pau

    2015-01-01

    Characterization of the intricate pore structure of calcium phosphate cements is a key step to successfully link the structural properties of these synthetic bone grafts with their most relevant properties, such as in vitro or in vivo behaviour, drug loading and release properties, or degradation over time. This is a challenging task due to the wide range of pore sizes in calcium phosphate cements, compared to most other ceramic biomaterials. This work provides a critical assessment of three ...

  18. Development and characterisation of injectable calcium phosphate cements for use in vertebroplasty

    OpenAIRE

    Pittet, Christian; Lemaître, Jacques

    2007-01-01

    The global objective of this thesis was to understand how the starting components of brushite cements influence the cement properties relevant for its use in vertebroplasty. Therefore, this work focussed on the following cement properties : mechanical strength, X-ray opacity and heat release upon setting. To carry out the global objective, a test protocol was first developed to characterise the mechanical properties of calcium phosphate cements. The Mohr's circles representation allowed to un...

  19. Development and characterisation of injectable calcium phosphate cements for use in vertebroplasty

    OpenAIRE

    Pittet, Christian

    2002-01-01

    The global objective of this thesis was to understand how the starting components of brushite cements influence the cement properties relevant for its use in vertebroplasty. Therefore, this work focussed on the following cement properties : mechanical strength, X-ray opacity and heat release upon setting. To carry out the global objective, a test protocol was first developed to characterise the mechanical properties of calcium phosphate cements. The Mohr's circles representation allowed to un...

  20. The use of calcium phosphate cement in vertebroplasty of the base of odontoid process.

    Science.gov (United States)

    Zapałowicz, Krzysztof; Wojdyn, Maciej; Zieliński, Krzysztof Włodzimierz; Snopkowska-Wiaderna, Dorota

    2013-01-01

    The authors describe the use of bone cement containing calcium phosphate for vertebroplasty of the cavity in the base of odontoid process. A 23-year-old female patient was operated on by incision in lateral cervical area (anterior open access). After a blunt dissection, the working cannula (Kyphon) was introduced under fluoroscopic guidance through the C2 vertebral body to the cavity in the base of the odontoid process. Intraoperatively, biopsy of the lesion was taken and histo-pathological examination excluded the presence of neoplasm. The cavity, presumably haemangioma, was successfully filled with calcium phosphate bone cement KyphOsTM FS (Ky-phon). The proper filling without paravertebral cement leak was confirmed by postoperative computed tomography (CT). The CT and magnetic resonance imaging performed 9 months after the procedure showed that cement was still present in the cavity. This is the first use of calcium phosphate cement to conduct the vertebroplasty of C2 vertebra. PMID:24375006

  1. Characterization of cement calcium phosphate for use dental

    International Nuclear Information System (INIS)

    Calcium phosphates are interesting biological and medical attention due to its occurrence in different animal species and humans. Ceramics based on calcium phosphate in the form of implants or porous particulate materials, have proven to be suitable replacements for bone tissue when they are only subjected to small mechanical stresses. Was obtained research laboratory DEMA/UFCG a calcium phosphate phase. The goal is to characterize the material by X-ray diffraction (XRD) in order to analyze what the phases and infrared spectroscopy (FTIR) to identify the absorption bands of the bonding characteristic. Was identified by XRD phase present in the sample is hydroxyapatite Ca/P 1.67. In infrared spectroscopy has absorption bands characteristic of the phosphate group at 1032 cm1 region. (author)

  2. Evaluation of Calcium Phosphate Cement As a Root Canal Sealer Filling Material

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Calcium phosphate cement for root end sealing was obtained by mixing α-tricalcium phosphate and additives with an aqueous solution of citric. Powder and liquid were mixed at a ratio of 1.25g/mL. The biocompatibility of this material was investigated primarily by subcutaneous implantation tests. Then calcium phosphate cement was used to fill three adult dogs' root canal, both calcium hydroxide paste and hydroxyapatite paste as control. The animals were killed at 4,12,20 weeks postoperatively respectively. The effects of different materials on the apical closure, restoration of periapical tissues and adaptability to the dentinal surface were examined by optical and electronic microscope. The observation at 20 weeks shows that the calcium phosphate cement has the potentialities of being a root canal sealer filling material available for pulpless teeth with open-apex and destructive periapical tissue.

  3. Molecular mechanism of crystallization impacting calcium phosphate cements

    Energy Technology Data Exchange (ETDEWEB)

    Giocondi, J L; El-Dasher, B S; Nancollas, G H; Orme, C A

    2009-05-31

    theoretical modeling. The question changes from 'What types of molecules will inhibit brushite growth' to 'What type of molecule will interact with the [10-1]{sub Cc} step?' Similarly, to increase resorption rate, it would be most efficacious to target the slow moving [-100] step, perhaps by targeting the hydroxyl group which seem to stabilize this step compared to its otherwise similar mirror, [100]. In short, there are a number of opportunities where molecular scale imaging can provide new information that has the prospect to aid in optimizing calcium phosphate cements.

  4. An injectable calcium phosphate cement for the local delivery of paclitaxel to bone

    NARCIS (Netherlands)

    Lopez-Heredia, M.A.; Kamphuis, G.J.; Thune, P.C.; Oner, F.C.; Jansen, J.A.; Walboomers, X.F.

    2011-01-01

    Bone metastases are usually treated by surgical removal, fixation and chemotherapeutic treatment. Bone cement is used to fill the resection voids. The aim of this study was to develop a local drug delivery system using a calcium phosphate cement (CPC) as carrier for chemotherapeutic agents. CPC cons

  5. The effects of citric acid on the hydration of calcium phosphate cement

    Institute of Scientific and Technical Information of China (English)

    DAI Hong-lian; YAN Yu-hua; WANG You-fa; LI Shi-pu

    2001-01-01

    @@ INTRODUCTION Calcium phosphate cements (CPC) overcome the practical disadvantages of blocks or granulesl can be handled as a paste and sit in situ. Their structure and composition close to that of HAP make them biocompatible materials. 2 The conventional calcium phosphate cement had some problems such as long setting time (30~60 min) and low compressive strength, etc. In our system, an α-TCP/TTCP powder mixture was mixed with water containing citric acid to control the setting time and compressive strength. In this paper, the effects of various concentration citric acid solutions on the properties of the cement are reported.

  6. Characterization of a calcium phosphate cement based on alpha-tricalcium phosphate obtained by wet precipitation process

    International Nuclear Information System (INIS)

    There are several systems of calcium phosphate cements being studied. Those based on alpha-tricalcium phosphate are of particular interest. After setting they produce calcium deficient hydroxyapatite similar to bone like hydroxyapatite. This work aims to obtain alpha-tricalcium phosphate powders by the wet precipitation process, using calcium nitrate and phosphoric acid as reagents. This powder was characterized by infrared spectroscopy, X-ray diffraction and particle size distribution. In order to prepare the calcium phosphate cement, the powder was mixed with an accelerator in an aqueous solution. The mechanical properties of the cement were assessed and it was evaluated by means of apparent density, X-ray diffraction and scanning electron microscopy. The described method produced crystalline alpha-tricalcium phosphate as the major phase. The calcium phosphate cement showed high values of compression strength (50 MPa). The soaking of the cement in a simulated body fluid (SBF) formed a layer of hydroxyapatite like crystals in the surface of the samples. (author)

  7. Investigating calcium polyphosphate addition to a conventional calcium phosphate cement for bone-interfacing applications

    Science.gov (United States)

    Krausher, Jennifer Lynn

    Calcium phosphate cements (CPCs) are of great interest in bone regeneration applications because of their biocompatibility and osteoconductivity, and as delivery vehicles for therapeutics; however, delivery applications have been limited by adverse interactions between therapeutics and the cement setting reaction. Amorphous calcium polyphosphate (CPP) yields a biodegradable material with a demonstrated drug delivery capacity following appropriate processing. The incorporation of drug-loaded CPP into a CPC is under consideration as a method of minimizing adverse interactions and extending drug release. This thesis represents the first investigation into the effects of CPP addition on the properties, setting and antibiotic release profile of a conventional apatitic calcium phosphate cement. As-made, gelled and vancomycin-loaded CPP particulate were added to the powder component of a conventional dicalcium phosphate/tetracalcium phosphate CPC. The setting behaviour, set properties and microstructure of the resulting CPP-CPCs were evaluated with setting time testing (Gilmore needle method), pH testing, mechanical testing, SEM imaging, XRD and FTIR analysis. In vitro degradation and elution behaviour were evaluated by monitoring calcium release (atomic absorbance spectroscopy), mechanical strength and vancomycin release (UV-visual spectrophotometry). CPP addition was found to increase the setting time, reduce the mechanical strength and inhibit the conversion of the CPC starting powders to the set apatitic phase. The most likely mechanism for the observed effect of CPP addition was the adsorption of polyphosphate chains on the particle surfaces, which would inhibit the dissolution of the starting powders and the conversion of apatite precursor phases to apatite, leading to reduced mechanical properties. The detrimental effects of CPP were reduced by limiting the CPP fraction to less than a few weight per cent and increasing the size of the CPP particulate. CPP

  8. In vitro biocompatibility of chitosan/hyaluronic acid-containing calcium phosphate bone cements.

    Science.gov (United States)

    Hesaraki, Saeed; Nezafati, Nader

    2014-08-01

    The need for bone repair has increased as the population ages. In this research, calcium phosphate cements, with and without chitosan (CS) and hyaluronic acid (HA), were synthesized. The composition and morphological properties of cements were evaluated by X-ray diffraction and scanning electron microscopy. The acellular in vitro bioactivity revealed that different apatite morphologies were formed on the surfaces of cements after soaking in simulated body fluid. The in vitro osteoblastic cell biocompatibility of in situ forming cements was evaluated and compared with those of conventional calcium phosphate cements (CPCs). The viability and growth rate of the cells were similar for all CPCs, but better alkaline phosphatase activity was observed for CPC with CS and HA. Calcium phosphate cements supported attachment of osteoblastic cells on their surfaces. Spindle-shaped osteoblasts with developed cytoplasmic membrane were found on the surfaces of cement samples after 7 days of culture. These results reveal the potential of the CPC-CS/HA composites to be used in bone tissue engineering. PMID:24399509

  9. Mechanical evaluation of implanted calcium phosphate cement incorporated with PLGA microparticles.

    NARCIS (Netherlands)

    Link, D.P.; Dolder, J. van den; Jurgens, W.J.; Wolke, J.G.C.; Jansen, J.A.

    2006-01-01

    In this study, the mechanical properties of an implanted calcium phosphate (CaP) cement incorporated with 20wt% poly (dl-lactic-co-glycolic acid) (PLGA) microparticles were investigated in a rat cranial defect. After 2, 4 and 8 weeks of implantation, implants were evaluated mechanically (push-out te

  10. Preparation and Compressive Strength of Calcium Phosphate Bone Cement Containing N, O-carboxymethyl Chitosan

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    N, O-carboxymethyl chitosan ( CMCTS ), a kind of biodegradable organic substance, was added to calcium phosphate bone cement (CPC) to produce a composite more similar in composition to human bone. The compressive strength of the new material was increased by 10 times compared with conventional CPC.

  11. An experimental approach to the study of the rheology behaviour of synthetic bone calcium phosphate cements

    Energy Technology Data Exchange (ETDEWEB)

    Friberg, J.; Fernandez, E.; Sarda, S.; Nilsson, M.; Ginebra, M.P.; Planell, J.A. [Universidad Politecnica de Catalunya, Barcelona (Spain). Dept. of Materials Science and Metallurgical Engineering; Martinez, S. [Barcelona Univ. (Spain). Mineralogia i Recursos Minerals

    2001-07-01

    Calcium phosphate cements were developed to fit surgical needs in biomedical fields such as odontology or traumatology. Nowadays, a broad field of new applications have been found for this kind of materials. Drug delivery systems, tissue-engineering scaffolds and osteoporotic bone filling applications are some of the new fields that are being benefited with these materials. Looking at both, commercial and new experimental calcium phosphate cements it is found that {alpha}-tricalcium phosphate is the main reactive powder responsible for the setting and the hardening of the cement. Thus, it is important to know how {alpha}-tricalcium phosphate affects injectability of these cements. The aim of this study was to investigate the rheological behaviour of {alpha}-tricalcium phosphate slurries in order to know how the cement injectability should be modified. Factors such as liquid to powder ratio, particle size of the main reactive powder and the addition of dispersants have been considered. The results showed that viscosity decreased when particle size of reactant was increased and when liquid to powder ratio was increased. It was also found that a minimum of viscosity exists at an optimum value of the weight percentage of dispersant. (orig.)

  12. In vitro osteoblast-like and endothelial cells' response to calcium silicate/calcium phosphate cement

    International Nuclear Information System (INIS)

    This study aims to investigate the interaction between calcium silicate/calcium phosphate cement (CS/CPC) and osteogenesis, in particular the in vitro osteoblast-like and endothelial cells' response to CS/CPC. The effect of CS/CPC on cell attachment, proliferation and differentiation of murine osteoblast-like cell MC3T3-E1, as well as the influence on the cell attachment and proliferation of human umbilical vein endothelial cell (HUVEC), was studied in detail. Our results indicated that CS/CPC exhibited excellent biocompatibility to the osteoblast-like cells. Moreover, the morphology and cytoskeleton organization of MC3T3-E1 cultured on the CS/CPC disks suggested that CS/CPC induced better cell adhesion and cell spreading. Simultaneously, cell proliferation and alkaline phosphatase (ALP) activity of MC3T3-E1 were significantly improved after 3 and 7 days of culture on CS/CPC disks in comparison with CPC disks. Additionally, on CS/CPC disks, HUVEC attached well on day 1 and cell proliferation was also greatly enhanced by day 7. Collectively, these results suggest that the introduction of calcium silicate may improve the cell response involved in the osteogenesis and thus may be beneficial to further modify CPC as a better bone repairing material.

  13. Development of a fully injectable calcium phosphate cement for orthopedic and dental applications

    Indian Academy of Sciences (India)

    Manoj Komath; H K Varma

    2003-06-01

    A study on the development of a fully injectable calcium phosphate cement for orthopedic and dental applications is presented. The paper describes its characteristic properties including results of bio- compatibility studies. A conventional two-component calcium phosphate cement formulation (having a powder part containing dry mixture of acidic and basic calcium phosphate particles and a liquid part containing phosphate solution) is modified with a biocompatible gelling agent, to induce flow properties and cohesion. The quantity of the gelling agent is optimized to get a viscous paste, which is smoothly injectable through an 18-gauge needle, with clinically relevant setting parameters. The new formulation has a setting time of 20 min and a compressive strength of 11 MPa. The X-ray diffraction, Fourier transform infrared spectrometry, and energy dispersive electron microprobe analyses showed the phase to be hydroxyapatite, the basic bone mineral. Scanning electron microscopy revealed a porous structure with particle sizes of a few micrometers. The cement did not show any appreciable dimensional or thermal change during setting. The injectability is estimated by extruding through needle and the cohesive property is assessed by water contact method. The cement passed the in vitro biocompatibility screening (cytotoxicity and haemolysis) tests.

  14. In-situ observation on the transformation of calcium phosphate cement into hydroxyapatite

    International Nuclear Information System (INIS)

    In the present study, the in-situ transformation of calcium phosphate cement into hydroxyapatite (HAp) within the first hour is monitored with a synchrotron X-ray beam. A disodium hydrogen phosphate solution is used as cement liquid to activate the reaction between dicalcium phosphate anhydrous (DCPA) and calcium hydroxide (Ca(OH)2). The XRD analysis indicates that the amounts of DCPA and Ca(OH)2 first decrease within the first min of the reaction. Then, the intensity of DCPA's XRD peaks starts to increase instead in the period of 5 to 20 min. After 20 min, the DCPA particles are consumed slowly to form fine HAp particles. Large pores are evident upon the completion of reaction.

  15. Solid-state P-31 MR studies of bone mineral and calcium phosphate bone cements

    International Nuclear Information System (INIS)

    Calcium phosphate bone cements have recently been used to promote bone healing and remodeling, but little is known of their bioabsorption. The purpose of this paper to characterize and quantitate bone mineral and calcium phosphate bone cements with the use of solid-state P-31 NMR imaging to establish a model for bioabsorption studies. Pulverized cortical rabbit bone, octacalcium phosphate spherulites, and two synthetic apatite formulations (A and B, Norian, Mountain View, Calif) were evaluated in vitro. A 9.4-T Varian VXR-400S spectrometer operating at 161.9 MHz for P-31 was used to obtain NMR imaging spectra with the magic-angel spinning technique at a sample spin frequency of 6-7.5 kHz, utilizing an external 85% phosphoric acid reference. T1 was determined in a static 90 degrees τ 90 degrees experiment. Quantitation was attempted in mixed samples

  16. Calcium phosphate holmium-166 ceramic to addition in bone cement: synthesis and characterization

    International Nuclear Information System (INIS)

    Spine metastases are a common and painful complication of cancer. The treatment often consists of bone cement injection (vertebroplasty or kyphoplasty) within vertebral body for vertebrae stabilization, followed by external beam radiation therapy. Recently, researchers introduced the concept of radioactive bone cement for spine tumors therapy. Then, investigations about bioactive and radioactive materials became interesting. In this study, we present the synthesis of calcium phosphate incorporated holmium (CaP-Ho) via sol-gel technique, and its characterization by XRD, FT-IR, NA and SEM. Results showed a multiphasic bioceramic composed mainly of hydroxyapatite, β-tricalcium phosphate, holmium phosphate and traces of calcium pyrophosphate. Furthermore, the nuclide Ho-166 was the major radioisotope produced. Despite that, the radioactive bioceramic CaP-166Ho must be investigated in clinical trials to assure its efficacy and safety on spine tumors treatment (author)

  17. Calcium phosphate holmium-166 ceramic to addition in bone cement: synthesis and characterization

    Energy Technology Data Exchange (ETDEWEB)

    Donanzam, Blanda A.; Campos, Tarcisio P.R., E-mail: campos@nuclear.ufmg.b [Universidade do Federal de Minas Gerais (DEN/UFMG), Belo Horizonte, MG (Brazil). Escola de Engenharia. Dept. de Engenharia Nuclear; Dalmazio, Ilza; Valente, Eduardo S., E-mail: id@cdtn.b, E-mail: valente@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    Spine metastases are a common and painful complication of cancer. The treatment often consists of bone cement injection (vertebroplasty or kyphoplasty) within vertebral body for vertebrae stabilization, followed by external beam radiation therapy. Recently, researchers introduced the concept of radioactive bone cement for spine tumors therapy. Then, investigations about bioactive and radioactive materials became interesting. In this study, we present the synthesis of calcium phosphate incorporated holmium (CaP-Ho) via sol-gel technique, and its characterization by XRD, FT-IR, NA and SEM. Results showed a multiphasic bioceramic composed mainly of hydroxyapatite, {beta}-tricalcium phosphate, holmium phosphate and traces of calcium pyrophosphate. Furthermore, the nuclide Ho-166 was the major radioisotope produced. Despite that, the radioactive bioceramic CaP-{sup 166}Ho must be investigated in clinical trials to assure its efficacy and safety on spine tumors treatment (author)

  18. Silicon-stabilized α-tricalcium phosphate and its use in a calcium phosphate cement: characterization and cell response.

    Science.gov (United States)

    Mestres, Gemma; Le Van, Clemence; Ginebra, Maria-Pau

    2012-03-01

    α-Tricalcium phosphate (α-TCP) is widely used as a reactant in calcium phosphate cements. This work aims at doping α-TCP with silicon with a twofold objective. On the one hand, to study the effect of Si addition on the stability and reactivity of this polymorph. On the other, to develop Si-doped cements and to evaluate the effect of Si on their in vitro cell response. For this purpose a calcium-deficient hydroxyapatite was sintered at 1250°C with different amounts of silicon oxide. The high temperature polymorph α-TCP was stabilized by the presence of silicon, which inhibited reversion of the β→α transformation, whereas in the Si-free sample α-TCP completely reverted to the β-polymorph. However, the β-α transformation temperature was not affected by the presence of Si. Si-α-TCP and its Si-free counterpart were used as reactants for a calcium phosphate cement. While Si-α-TCP showed faster hydrolysis to calcium-deficient hydroxyapatite, upon complete reaction the crystalline phases, morphology and mechanical properties of both cements were similar. An in vitro cell culture study, in which osteoblast-like cells were exposed to the ions released by both materials, showed a delay in cell proliferation in both cases and stimulation of cell differentiation, more marked for the Si-containing cement. These results can be attributed to strong modification of the ionic concentrations in the culture medium by both materials. Ca-depletion from the medium was observed for both cements, whereas continuous Si release was detected for the Si-containing cement. PMID:22154863

  19. An ultrasonic through-transmission technique for monitoring the setting of injectable calcium phosphate cement.

    Science.gov (United States)

    Rajzer, Izabella; Piekarczyk, Wojciech; Castaño, Oscar

    2016-10-01

    An ultrasound through-transmission method to monitor the setting process of injectable calcium phosphate bone cements in body fluids is presented. This method can be used to determine the acoustic properties of the bone cement as it sets, which are linked to its material properties and provide some information about changes occurring within the cement. The development of the methodology of ultrasonic testing and execution of velocity measurements of the longitudinal and transverse waves using the through-transmission method made it possible to determine the material constants of samples during the setting and hardening process of an injectable cement paste in physiological fluids (i.e. the Young's modulus (E), the Poisson ratio (ν) and the shear modulus (G)), and to determine the degree of anisotropy of wave velocity in the samples. A strong advantage of the proposed method is that it is non-destructive, and the same sample can be used to monitor the whole process of the cement setting. The testing was performed on premixed and injectable calcium phosphate (CPC)/chitosan blend, where glycerol was used as a liquid phase. Comparisons between ultrasonic velocity and empirical tests such as compressive strength, porosity measurement, FTIR, SEM and XRD analysis at different days of immersion in Ringer's solutions showed that the ultrasonic velocity can be very useful to provide in situ information about changes occurring within the cement. PMID:27287094

  20. The In-situ Reinforcement of Calcium Phosphate Cement and Its Micro-structural Analysis

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Carbon nanotubes ( CNTs ) and polyacrylic acid were employed to modify the setting process and hydration products of β- TCP/ TTCP calcium phosphate cement. The micro-structure of hydration product and the fashion of how additives and hydration particles interconnected were investigated. With the modification effect of CNTs, the setting particles and CNTs got winded and interconnected and thus made the composite more compact and denser.

  1. Physicochemical properties and biocompatibility of chitosan oligosaccharide/gelatin/calcium phosphate hybrid cements

    International Nuclear Information System (INIS)

    A bone substitute material was developed consisting of a chitosan oligosaccharide (COS) solution in a liquid phase and gelatin (GLT) containing calcium phosphate powder in a solid phase. The physicochemical and biocompatible properties of the hybrid cements were evaluated. The addition of COS to cement did not affect the setting time or diametral tensile strength of the hybrid cements, whereas GLT significantly prolonged the setting time and decreased the strength slightly. The setting reaction was inhibited by the addition of GLT to the initial mixture, but not by COS. However, the presence of GLT appreciably improved the anti-washout properties of the hybrid cement compared with COS. COS may promote the cement's biocompatibility as an approximate twofold increase in cell proliferation for 10% COS-containing cements was observed on day 3 as compared with the controls. The combination of GLT and COS was chosen due to the benefits achieved from several synergistic effects and for their clinical applications. Cement with 5% GLT and 10% COS may be a better choice among cements in terms of anti-washout properties and biological activity.

  2. A New Type of Biphasic Calcium Phosphate Cement as a Gentamicin Carrier for Osteomyelitis

    Directory of Open Access Journals (Sweden)

    Wen-Yu Su

    2013-01-01

    Full Text Available Osteomyelitis therapy is a long-term and inconvenient procedure for a patient. Antibiotic-loaded bone cements are both a complementary and alternative treatment option to intravenous antibiotic therapy for the treatment of osteomyelitis. In the current study, the biphasic calcium phosphate cement (CPC, called α-TCP/HAP (α-tricalcium phosphate/hydroxyapatite biphasic cement, was prepared as an antibiotics carrier for osteomyelitis. The developed biphasic cement with a microstructure of α-TCP surrounding the HAP has a fast setting time which will fulfill the clinical demand. The X-ray diffraction and Fourier transform infrared spectrometry analyses showed the final phase to be HAP, the basic bone mineral, after setting for a period of time. Scanning electron microscopy revealed a porous structure with particle sizes of a few micrometers. The addition of gentamicin in α-TCP/HAP would delay the transition of α-TCP but would not change the final-phase HAP. The gentamicin-loaded α-TCP/HAP supplies high doses of the antibiotic during the initial 24 hours when they are soaked in phosphate buffer solution (PBS. Thereafter, a slower drug release is produced, supplying minimum inhibitory concentration until the end of the experiment (30 days. Studies of growth inhibition of Staphylococcus aureus and Pseudomonas aeruginosa in culture indicated that gentamicin released after 30 days from α-TCP/HAP biphasic cement retained antibacterial activity.

  3. Preparation, Physical-Chemical Characterization, and Cytocompatibility of Polymeric Calcium Phosphate Cements

    Directory of Open Access Journals (Sweden)

    Rania M. Khashaba

    2011-01-01

    Full Text Available Aim. Physicochemical mechanical and in vitro biological properties of novel formulations of polymeric calcium phosphate cements (CPCs were investigated. Methods. Monocalcium phosphate, calcium oxide, and synthetic hydroxyapatite were combined with either modified polyacrylic acid, light activated polyalkenoic acid, or polymethyl vinyl ether maleic acid to obtain Types I, II, and III CPCs. Setting time, compressive and diametral strength of CPCs was compared with zinc polycarboxylate cement (control. Specimens were characterized using X-ray diffraction, scanning electron microscopy, and infrared spectroscopy. In vitro cytotoxicity of CPCs and control was assessed. Results. X-ray diffraction analysis showed hydroxyapatite, monetite, and brushite. Acid-base reaction was confirmed by the appearance of stretching peaks in IR spectra of set cements. SEM revealed rod-like crystals and platy crystals. Setting time of cements was 5–12 min. Type III showed significantly higher strength values compared to control. Type III yielded high biocompatibility. Conclusions. Type III CPCs show promise for dental applications.

  4. The progress of early phase bone healing using porous granules produced from calcium phosphate cement

    Directory of Open Access Journals (Sweden)

    Jungbluth P

    2010-05-01

    Full Text Available Abstract Objective Bone grafting is a vital component in many surgical procedures to facilitate the repair of bone defects or fusions. Autologous bone has been the gold standard to date in spite of associated donor-site morbidity and the limited amount of available donor bone. The aim of this study was to investigate the progress of bone regeneration and material degradation of calcium phosphate granules (CPG produced from a calcium phosphate self-setting cement powder compared to the use of autologous bone grafting in the treatment of "critical size defects" on load-bearing long bones of minipigs. Methods A critical size defect in the tibial metaphysis of 16 mini-pigs was filled either with autologous cancellous graft or with micro- and macroporous carbonated, apatic calcium phosphate granules (CPG produced from a calcium phosphate self-setting cement powder. After 6 weeks, the specimens were assessed by X-ray and histological evaluation. The amount of new bone formation was analysed histomorphometrically. Results The semi-quantitative analysis of the radiological results showed a complete osseous bridging of the defect in three cases for the autograft group. In the same group five animals showed a beginning, but still incomplete bridging of the defect, whereas in the CPG group just two animals developed this. All other animals of the CPG group showed only a still discontinuous new bone formation. Altogether, radiologically a better osseous bridging was observed in the autograft group compared to the CPG group. Histomorphometrical analysis after six weeks of healing revealed that the area of new bone was significantly greater in the autograft group concerning the central area of the defect zone (p Conclusions Within the limits of the present study it could be demonstrated that autologous cancellous grafts lead to a significantly better bone regeneration compared to the application of calcium phosphate granules (CPG produced from a calcium

  5. CITRIC ACID AS A SET RETARDER FOR CALCIUM ALUMINATE PHOSPHATE CEMENTS.

    Energy Technology Data Exchange (ETDEWEB)

    SUGAMA,T.; BROTHERS, L.E.

    2005-01-01

    Citric acid added as set retarder significantly contributed to enhancing the setting temperature and to extending the thickening time of a calcium aluminate phosphate (CaP) geothermal cement slurry consisting of calcium aluminate cement (CAC) as the base reactant and sodium polyphosphate (NaP) solution as the acid reactant. The set-retarding activity of citric acid was due to the uptake of Ca{sup 2+} ions from the CAC by carboxylic acid groups within the citric acid. This uptake led to the precipitation of a Ca-complexed carboxylate compound as a set-retarding barrier layer on the CAC grains' surfaces. However, this barrier layer was vulnerable to disintegration by the attack of free Ca{sup 2+} ions from CAC, and also to degradation at elevated temperature, thereby promoting the generation of exothermic energy from acid-base reactions between the CAC and NaP after the barrier was broken. The exothermic reaction energy that was promoted in this way minimized the loss in strength of the citric acid-retarded cement. The phase composition assembled in both retarded and non-retarded cements after autoclaving at 180 C encompassed three reaction products, hydroxyapatite (HOAp), hydrogrossular and boehmite, which are responsible for strengthening the autoclaved cement. The first two reaction products were susceptible to reactions with sulfuric acid and sodium sulfate to form crystalline bassanite scale as the corrosion product. The boehmite phase possessed a great resistance to acid and sulfate. Although the bassanite scales clinging to the cement's surfaces were the major factor governing the loss in weight, they served in protecting the cement from further acid- and sulfate-corrosion until their spallation eventually occurred. Nevertheless, the repetitive processes of HOAp and hydrogrossular {yields} bassanite {yields} spallation played an important role in extending the useful lifetime of CaP cement in a low pH environment at 180 C.

  6. Monitoring of hardening and hygroscopic induced strains in a calcium phosphate bone cement using FBG sensor.

    Science.gov (United States)

    Bimis, A; Karalekas, D; Bouropoulos, N; Mouzakis, D; Zaoutsos, S

    2016-07-01

    This study initially deals with the investigation of the induced strains during hardening stage of a self-setting calcium phosphate bone cement using fiber-Bragg grating (FBG) optical sensors. A complementary Scanning Electron Microscopy (SEM) investigation was also conducted at different time intervals of the hardening period and its findings were related to the FBG recordings. From the obtained results, it is demonstrated that the FBG response is affected by the microstructural changes taking place when the bone cement is immersed into the hardening liquid media. Subsequently, the FBG sensor was used to monitor the absorption process and hygroscopic response of the hardened and dried biocement when exposed to a liquid/humid environment. From the FBG-based calculated hygric strains as a function of moisture concentration, the coefficient of moisture expansion (CME) of the examined bone cement was obtained, exhibiting two distinct linear regions. PMID:26807773

  7. Development of a novel fluorapatite-forming calcium phosphate cement with calcium silicate: in vitro and in vivo characteristics.

    Science.gov (United States)

    Suzuki, Yusuke; Hayashi, Makoto; Yasukawa, Takuya; Kobayashi, Hiroshi; Makino, Kosuke; Hirano, Yoriyuki; Takagi, Shozo; Chow, Laurence C; Ogiso, Bunnai

    2015-01-01

    Aim of this study was to develop a novel fluorapatite-forming calcium phosphate cement (FA-CPC) with tricalcium silicate (TCS) for endodontic applications and to examine its in vitro and in vivo characteristics. The FA-CPC powder consisted of 62.8% CaHPO4, 30.8% CaCO3, and 6.4% NaF. One part of TCS was combined with 9 parts of FA-CPC powder (FA-CPC with TCS). A 1.5 M phosphate solution was used as cement liquid. Setting time (ST), diametral tensile strength (DTS), phase composition by X-ray diffraction (XRD), and cement alkalinity were analyzed. Cement biocompatibility was assessed using rat subcutaneous model. Cement ST was 10.3±0.6 min and DTS was 3.89±0.76 MPa. XRD patterns showed that highly crystalline apatitic material was the only significant phase present and pH value was approximate 11.0. FA-CPC with TCS demonstrated similar biocompatibility as that of mineral trioxide aggregate control. These results suggest that FA-CPC with TCS may be useful for endodontic applications. PMID:25740309

  8. Augmentation of femoral neck fracture fixation with an injectable calcium-phosphate bone mineral cement.

    Science.gov (United States)

    Stankewich, C J; Swiontkowski, M F; Tencer, A F; Yetkinler, D N; Poser, R D

    1996-09-01

    The first goal of this study was to determine if augmentation with an injectable, in situ setting, calcium-phosphate cement that is capable of being remodeled and was designed to mimic bone mineral significantly improved the strength and stiffness of fixation in a cadaveric femoral neck fracture model. The second goal was to determine if greater increases in fixation strength were achieved as the bone density of the specimen decreased. Sixteen pairs of fresh cadaveric human femora with a mean age of 70.9 years (SD = 17.2 years) were utilized. The bone density of the femoral neck was measured with dual-energy x-ray absorptiometry. The femoral head was impacted vertically with the femoral shaft fixed in 12 degrees of adduction using a materials testing machine to create a fully displaced fracture. Following fracture, 30% inferior comminution was created in each specimen. One randomly chosen femur from each pair underwent anatomic reduction and fixation with three cannulated cancellous bone screws, 7 mm in diameter, in an inverted triangle configuration. The contralateral femur underwent the same fixation augmented with calcium-phosphate cement. Specimens were preconditioned followed by 1.000 cycles to one body weight (611.6 N) at 0.5 Hz to simulate single-limb stance loading. The stiffness in the first cycle was observed to be significantly greater in cement-augmented specimens compared with unaugmented controls (p bone mineral cement failed at a mean of 4,573 N (SD = 1,243 N); this was significantly greater (p bone density (p = 0.25, R2 = 0.09), was weakly correlated to the volume of cement injected (p = 0.07, R2 = 0.22), and was inversely related to the fixation failure load of the control specimen (p = 0.001, R2 = 0.54). There was a mean relative improvement in fixation strength of 169.6% (SD = 77.5). These findings suggest that calcium-phosphate cement provides initial beneficial augmentation to fixation of femoral neck fractures. PMID:8893773

  9. Mechanical evaluation of implanted calcium phosphate cement incorporated with PLGA microparticles

    OpenAIRE

    Link, Dennis P.; VAN DEN DOLDER, Juliette; Jurgens, J. F. M.; Wolke, Joop G.; Jansen, John A.

    2006-01-01

    In this study, the mechanical properties of an implanted calcium phosphate (CaP) cement incorporated with 20wt% poly (DL-lactic-coglycolic acid) (PLGA) microparticles were investigated in a rat cranial defect. After 2, 4 and 8 weeks of implantation, implants were evaluated mechanically (push-out test) and morphologically (Scanning Electron Microscopy (SEM) and histology). The results of the push-out test showed that after 2 weeks the shear strength of the implants was 0.4470.44MPa (a...

  10. Modifications on the properties of a calcium phosphate cement by additions of sodium alginate

    Energy Technology Data Exchange (ETDEWEB)

    Coelho, W.T.; Fernandes, J.M.; Vieira, R.S.; Thurmer, M.B.; Santos, L.A., E-mail: trajano@ufrgs.br, E-mail: julianafernandes2@yahoo.com.br, E-mail: rsvieira.eng@gmail.com, E-mail: monicathurmer@yahoo.com.br, E-mail: luis.santos@ufrgs.br [Universidade Federal do Rio Grande do Sul (PPG/LABIOMAT/UFRGS), RS (Brazil)

    2012-07-01

    The Calcium Phosphate Cement (CPC) are bone substitutes with great potential for use in orthopedics, traumatology and dentistry due to its biocompatibility, bioactivity and osteoconductivity, and form a paste that can be easily shaped and placed into the surgical site. However, CPCs have low mechanical strength, which equals the maximum mechanical strength of trabecular bone. In order to assess the strength and time to handle a CPC composed primarily of alpha phase, were added sodium alginate (1%, 2% and 3% wt) and an accelerator in an aqueous solution. The cement powder was mixed with liquid of setting, shaped into specimens and evaluated for apparent density and porosity by Archimedes method, X-ray diffraction and compressive strength. A significant increase in compressive strength by adding sodium alginate was verified. (author)

  11. Modifications on the properties of a calcium phosphate cement by additions of sodium alginate

    International Nuclear Information System (INIS)

    The Calcium Phosphate Cement (CPC) are bone substitutes with great potential for use in orthopedics, traumatology and dentistry due to its biocompatibility, bioactivity and osteoconductivity, and form a paste that can be easily shaped and placed into the surgical site. However, CPCs have low mechanical strength, which equals the maximum mechanical strength of trabecular bone. In order to assess the strength and time to handle a CPC composed primarily of alpha phase, were added sodium alginate (1%, 2% and 3% wt) and an accelerator in an aqueous solution. The cement powder was mixed with liquid of setting, shaped into specimens and evaluated for apparent density and porosity by Archimedes method, X-ray diffraction and compressive strength. A significant increase in compressive strength by adding sodium alginate was verified. (author)

  12. A histological evaluation on osteogenesis and resorption of methotrexate-loaded calcium phosphate cement in vivo

    International Nuclear Information System (INIS)

    In this study, we investigated the resorption of in vivo methotrexate-loaded calcium phosphate cement (MTX-CPC) implants and their effect on osteogenesis. MTX-CPC implants containing 1% methotrexate (MTX) (weight/weight) were preset and implanted into the femoral condyle of rabbits. Calcium phosphate cement (CPC) without MTX was used as the control. The femurs were harvested at day 1 and at 1, 3 and 6 months after implantation and radiological examination were performed. Decalcified sections were examined by hematoxylin and eosin (HE) staining, alkaline phosphatase (ALPase) immunohistochemistry and tartrate-resistant acid phosphatase (TRAPase) enzyme histochemistry. Then, we performed histomorphometric analysis, including determination of the percentage of newly formed bone and osteoblast and osteoclast counts. The results indicated that MTX-CPC implants were biocompatible, biodegradable and osteoconducive. However, MTX release from the implantation site inhibited osteogenesis in the initial period; this inhibition weakened with time, and no difference was observed between CPC and MTX-CPC at 6 months after implantation. Hence, MTX-CPC is an excellent material for filling defects and can be used for preparing effective drug delivery systems to achieve local control of invasive bone tumors.

  13. A histological evaluation on osteogenesis and resorption of methotrexate-loaded calcium phosphate cement in vivo

    Energy Technology Data Exchange (ETDEWEB)

    Li Dong; Yang Zhiping; Li Xin; Li Zhenfeng; Li Jianmin [Department of Orthopedics, Qilu Hospital of Shandong University, Shandong (China); Yang Jingyan, E-mail: yangzhiping@medmail.com.c [Department of Pathology, 2nd Affiliated Hospital of Shandong University, Shandong (China)

    2010-04-15

    In this study, we investigated the resorption of in vivo methotrexate-loaded calcium phosphate cement (MTX-CPC) implants and their effect on osteogenesis. MTX-CPC implants containing 1% methotrexate (MTX) (weight/weight) were preset and implanted into the femoral condyle of rabbits. Calcium phosphate cement (CPC) without MTX was used as the control. The femurs were harvested at day 1 and at 1, 3 and 6 months after implantation and radiological examination were performed. Decalcified sections were examined by hematoxylin and eosin (HE) staining, alkaline phosphatase (ALPase) immunohistochemistry and tartrate-resistant acid phosphatase (TRAPase) enzyme histochemistry. Then, we performed histomorphometric analysis, including determination of the percentage of newly formed bone and osteoblast and osteoclast counts. The results indicated that MTX-CPC implants were biocompatible, biodegradable and osteoconducive. However, MTX release from the implantation site inhibited osteogenesis in the initial period; this inhibition weakened with time, and no difference was observed between CPC and MTX-CPC at 6 months after implantation. Hence, MTX-CPC is an excellent material for filling defects and can be used for preparing effective drug delivery systems to achieve local control of invasive bone tumors.

  14. Bioactive calcium sulfate/magnesium phosphate cement for bone substitute applications

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Guangyong [Department of Orthopaedics, Taizhou Hospital of Zhejiang Province, Linhai Zhejiang, 317000 (China); Department of Orthopaedic Surgery, Second Affiliated Hospital of Wenzhou Medical College, Wenzhou, Zhejiang, 325000 (China); Liu, Jianli [Trauma Center, Affiliated Hospital of Hainan Medical University, Haikou, Hainan, 570206 (China); Division of Functional Materials and Nanodevices, Ningbo Institute of Materials Technology and Engineering (NIMTE), Chinese Academy of Sciences (CAS), Ningbo, Zhejiang, 315201 (China); Li, Fan; Pan, Zongyou; Ni, Xiao; Shen, Yue [Department of Orthopaedic Surgery, Second Affiliated Hospital of Wenzhou Medical College, Wenzhou, Zhejiang, 325000 (China); Xu, Huazi, E-mail: spinexu@163.com [Department of Orthopaedic Surgery, Second Affiliated Hospital of Wenzhou Medical College, Wenzhou, Zhejiang, 325000 (China); Huang, Qing, E-mail: huangqing@nimte.ac.cn [Division of Functional Materials and Nanodevices, Ningbo Institute of Materials Technology and Engineering (NIMTE), Chinese Academy of Sciences (CAS), Ningbo, Zhejiang, 315201 (China)

    2014-02-01

    A novel calcium sulfate/magnesium phosphate cement (CSMPC) composite was prepared and studied in the present work. The physical properties including the phases, the microstructures, the setting properties and the compressive strengths of the CSMPCs were studied. The bio-performances of the CSMPCs were comprehensively evaluated using in vitro simulated body fluid (SBF) method and in vitro cell culture. The dependence of the physical and chemical properties of the CSMPC on its composition and microstructure was studied in detail. It is found that the CSMPC composites exhibited mediate setting times (6–12 min) compared to the calcium sulfate (CS) and the magnesium phosphate cement (MPC). They showed an encapsulation structure in which the unconverted hexagonal prism CSH particles were embedded in the xerogel-like MPC matrix. The phase compositions and the mechanical properties of the CSMPCs were closely related to the content of MPC and the hardening process. The CSMPCs exhibited excellent bioactivity and good biocompatibility to support the cells to attach and proliferate on the surface. The CSMPC composite has the potential to serve as bone grafts for the bone regeneration. - Highlights: • The mechanical strength and degradation rate of CSMPC composites are discussed. • The CSMPC composites exhibited good bioactivity to form bone-like apatite. • The CSMPC composites also show good biocompatibility.

  15. Bioactive calcium sulfate/magnesium phosphate cement for bone substitute applications

    International Nuclear Information System (INIS)

    A novel calcium sulfate/magnesium phosphate cement (CSMPC) composite was prepared and studied in the present work. The physical properties including the phases, the microstructures, the setting properties and the compressive strengths of the CSMPCs were studied. The bio-performances of the CSMPCs were comprehensively evaluated using in vitro simulated body fluid (SBF) method and in vitro cell culture. The dependence of the physical and chemical properties of the CSMPC on its composition and microstructure was studied in detail. It is found that the CSMPC composites exhibited mediate setting times (6–12 min) compared to the calcium sulfate (CS) and the magnesium phosphate cement (MPC). They showed an encapsulation structure in which the unconverted hexagonal prism CSH particles were embedded in the xerogel-like MPC matrix. The phase compositions and the mechanical properties of the CSMPCs were closely related to the content of MPC and the hardening process. The CSMPCs exhibited excellent bioactivity and good biocompatibility to support the cells to attach and proliferate on the surface. The CSMPC composite has the potential to serve as bone grafts for the bone regeneration. - Highlights: • The mechanical strength and degradation rate of CSMPC composites are discussed. • The CSMPC composites exhibited good bioactivity to form bone-like apatite. • The CSMPC composites also show good biocompatibility

  16. Formation of interconnected macropores in apatitic calcium phosphate bone cement with the use of an effervescent additive.

    Science.gov (United States)

    Hesaraki, S; Moztarzadeh, F; Sharifi, D

    2007-10-01

    Calcium phosphate cements (CPCs) can be considered as good candidate for bone tissue engineering because they can be resorbed and take part in the bone remodeling process. Several efforts have been made into improve the resorption rate of the calcium phosphate cement by introducing macropores to the cement matrix. In this investigation a simple and effective method has been presented based on the addition of various amounts of an effervescent agent to the calcium phosphate cement components. The effervescent agent was a mixture of sodium hydrogen carbonate, NaHCO(3) (that was added to the powder phase), and citric acid monohydrate, C(6)H(8)O(7).H(2)O (that was dissolved in the liquid phase). The obtained macroporous samples were characterized by Fourier transform infrared spectrometer, X-ray diffraction, and scanning electron microscopy techniques at 4 h after setting and 3 days after soaking in a special simulated body fluid solution named Hank's balanced salt solution. Mercury intrusion porosimetry was also employed for characterizing the pore volume and pore size distribution in the cement structure. Results showed that the rate of conversion of staring reactant to the apatite phase and the apatite chemistry were significantly changed by using the additive in the cement components. Also both the pore volume and pore size were changed by varying both the amount of effervescent additive and the powder to liquid ratio. PMID:17380498

  17. The effect of supplementary pulverized fuel ash on calcium aluminate phosphate cement for intermediate-level waste encapsulation

    International Nuclear Information System (INIS)

    The objective of the current study was to evaluate the effects of supplementary pulverized fuel ash on phosphate-modified calcium aluminate cement. These systems are being established as part of a wider project to develop alternative cementing systems for the encapsulation of problematic low- and intermediate- level radioactive waste in the UK. The nuclear industry has established specific processing and property criteria, which must be fulfilled to ensure suitability for industrial application. In a series of studies, pulverized fuel ash was used as a partial replacement for calcium aluminate cement, to improve the fluidity of the system and increase the setting time. Properties such as slurry pH and fluidity, setting time, mechanical properties, and porosity were investigated using Vicat, Colflow, and compressive strength testing equipment and mercury intrusion porosimetry. The hardened cement pastes were also characterised using X-ray diffraction, thermogravimetric analysis and scanning electron microscopy. A formulation envelope was identified, which fulfilled the plant acceptance tests defined by industry to ensure suitability for industrial application. It was found that pH of calcium aluminate phosphate cements is lower than that of conventional cementing systems used to encapsulate radioactive waste in the UK. Hence, they have potential to be used as an alternative cementing system for the encapsulation of problematic radioactive metals. (authors)

  18. A Comprehensive Study of Osteogenic Calcium Phosphate Silicate Cement: Material Characterization and In Vitro/In Vivo Testing.

    Science.gov (United States)

    Gong, Tianxing; Wang, Zhiqin; Zhang, Yixi; Zhang, Yubiao; Hou, Mingxiao; Liu, Xinwei; Wang, Yu; Zhao, Lejun; Ruse, N Dorin; Troczynski, Tom; Häfeli, Urs O

    2016-02-18

    Vertebral compression fractures can be successfully restored by injectable bone cements. Here the as-yet unexplored in vitro cytotoxicity, in vivo biodegradation, and osteoconductivity of a new calcium phosphate silicate cements (CPSC) are studied, where monocalcium phosphate (MCP; 5, 10, and 15 wt%) is added to calcium silicate cement (CSC). Setting rate and compressive strength of CPSC decrease with the addition of MCP. The crystallinity, microstructure, and porosity of hardened CPSC are evaluated by X-ray diffractometer, Fourier transform infrared spectroscopy, and microcomputed tomography (CT). It is found that MCP reacts with calcium hydroxide, one of CSC hydration products, to precipitate apatite. While the reaction accelerates the hydration of CSC, the formation of calcium silicate hydrate gel is disturbed and highly porous microstructures form, resulting in weaker compressive strength. In vitro studies demonstrate that CPSC is noncytotoxic to osteoblast cells and promotes their proliferation. In the rabbit tibia implantation model, clinical X-ray and CT scans demonstrate that CPSC biodegrades slower and osseointegrates better than clinically used calcium phosphate cement (CPC). Histological studies demonstrate that CPSC is osteoconductive and induces higher bone formation than CPC, a finding that might warrant future clinical studies. PMID:26677175

  19. Effect of polydopamine on the biomimetic mineralization of mussel-inspired calcium phosphate cement in vitro

    International Nuclear Information System (INIS)

    Inspired by the excellent adhesive property of mussel adhesive protein, we added polydopamine (PDA) to calcium phosphate cement (PDA–CPC) to enhance its compressive strength previously. The mineralization and mechanism on PDA–CPC were investigated by soaking it in simulated body fluid in this study. The results indicated that PDA promoted the conversion of dicalcium phosphate dihydrate and α-tricalcium phosphate to hydroxyapatite (HA) in the early stage but inhibited this conversion subsequently. PDA promoted the rapid mineralization on PDA–CPC to form a layer of nanoscale calcium phosphate (CaP) whereas there was no CaP formation on the control-CPC after 1 d of soaking. This layer of nanoscale CaP was similar to that of natural bone, which was always observed during soaking. X-ray photoelectron spectroscopy showed that the peak of C=O of PDA existed in the newly formed CaP on PDA–CPC, indicating the co-precipitation of CaP with PDA. Furthermore, the newly formed CaP on PDA–CPC was HA confirmed by transmission electron microscopy, which the newly formed HA was in association with PDA. Therefore, PDA increased the capacity of mineralization of CPC and induced the formation of nanoscale bone-like apatite on PDA–CPC. Thus, this provides the feasible route for surface modification on CPC. - Highlights: • Effect of polydopamine (PDA) on the in vitro mineralization of PDA-CPC was studied. • PDA promoted the rapid mineralization on PDA-CPC to form a nanoscale HA layer. • The precipitation of the nanoscale HA layer on PDA-CPC accompanied with PDA. • Polydopamine induced mineralization is feasible for surface modification of CaP

  20. Effect of polydopamine on the biomimetic mineralization of mussel-inspired calcium phosphate cement in vitro

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Zongguang [Key Lab of Advanced Technologies of Materials, Ministry of Education, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031 (China); Qu, Shuxin, E-mail: qushuxin@swjtu.edu.cn [Key Lab of Advanced Technologies of Materials, Ministry of Education, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031 (China); Zheng, Xiaotong; Xiong, Xiong [Key Lab of Advanced Technologies of Materials, Ministry of Education, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031 (China); Fu, Rong; Tang, Kuangyun; Zhong, Zhendong [Department of Plastic Surgery, Academy of Medical Sciences and Sichuan Provincial People' s Hospital, Chengdu 610041 (China); Weng, Jie [Key Lab of Advanced Technologies of Materials, Ministry of Education, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031 (China)

    2014-11-01

    Inspired by the excellent adhesive property of mussel adhesive protein, we added polydopamine (PDA) to calcium phosphate cement (PDA–CPC) to enhance its compressive strength previously. The mineralization and mechanism on PDA–CPC were investigated by soaking it in simulated body fluid in this study. The results indicated that PDA promoted the conversion of dicalcium phosphate dihydrate and α-tricalcium phosphate to hydroxyapatite (HA) in the early stage but inhibited this conversion subsequently. PDA promoted the rapid mineralization on PDA–CPC to form a layer of nanoscale calcium phosphate (CaP) whereas there was no CaP formation on the control-CPC after 1 d of soaking. This layer of nanoscale CaP was similar to that of natural bone, which was always observed during soaking. X-ray photoelectron spectroscopy showed that the peak of C=O of PDA existed in the newly formed CaP on PDA–CPC, indicating the co-precipitation of CaP with PDA. Furthermore, the newly formed CaP on PDA–CPC was HA confirmed by transmission electron microscopy, which the newly formed HA was in association with PDA. Therefore, PDA increased the capacity of mineralization of CPC and induced the formation of nanoscale bone-like apatite on PDA–CPC. Thus, this provides the feasible route for surface modification on CPC. - Highlights: • Effect of polydopamine (PDA) on the in vitro mineralization of PDA-CPC was studied. • PDA promoted the rapid mineralization on PDA-CPC to form a nanoscale HA layer. • The precipitation of the nanoscale HA layer on PDA-CPC accompanied with PDA. • Polydopamine induced mineralization is feasible for surface modification of CaP.

  1. Calcium phosphate cement reinforcement by polymer infiltration and in situ curing: a method for 3D scaffold reinforcement.

    Science.gov (United States)

    Alge, Daniel L; Chu, Tien-Min Gabriel

    2010-08-01

    This study describes a novel method of calcium phosphate cement reinforcement based on infiltrating a pre-set cement with a reactive polymer and then cross-linking the polymer in situ. This method can be used to reinforce 3D calcium phosphate cement scaffolds, which we demonstrate using poly(ethylene glycol) diacrylate (PEGDA) as a model reinforcing polymer. The compressive strength of a 3D scaffold comprised of orthogonally intersecting beams was increased from 0.31 +/- 0.06 MPa to 1.65 +/- 0.13 MPa using PEGDA 600. In addition, the mechanical properties of reinforced cement were characterized using three PEGDA molecular weights (200, 400, and 600 Da) and three cement powder to liquid (P/L) ratios (0.8, 1.0, and 1.43). Higher molecular weight increased reinforcement efficacy, and P/L controlled cement porosity and determined the extent of polymer incorporation. Although increasing polymer incorporation resulted in a transition from brittle, cement-like behavior to ductile, polymer-like behavior, maximizing polymer incorporation was not advantageous. Polymerization shrinkage produced microcracks in the cement, which reduced the mechanical properties. The most effective reinforcement was achieved with P/L of 1.43 and PEGDA 600. In this group, flexural strength increased from 0.44 +/- 0.12 MPa to 7.04 +/- 0.51 MPa, maximum displacement from 0.05 +/- 0.01 mm to 1.44 +/- 0.17 mm, and work of fracture from 0.64 +/- 0.10 J/m(2) to 677.96 +/- 70.88 J/m(2) compared to non-reinforced controls. These results demonstrate the effectiveness of our novel reinforcement method, as well as its potential for fabricating reinforced 3D calcium phosphate cement scaffolds useful for bone tissue engineering. PMID:20186776

  2. Calcium phosphate cements properties with polymers addition; Propriedades do cimento de fosfato de calcio com adicao de polimeros

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, J.M.; Trajano, W.T.; Escobar, C.F.; Santos, L.A., E-mail: julianafernandes2@yahoo.com.br [Universidade Federal do Rio Grande do Sul (UFRGS), RS (Brazil)

    2012-07-01

    Calcium phosphate cements (CPC) have attracted great interest to use in orthopedics and dentistry as replacements for damaged parts of the skeletal system, showing good biocompatibility and osseointegration, allowing its use as bone graft. Several studies have shown that the addition of polymer additives have a strong influence on the cement properties. The low mechanical strength is the main obstacle to greater use of CPC as an implant material. The objective of this study was to evaluate properties of a cement based on α-tricalcium phosphate (α-TCP), added polymers. PVA (10%, 8%, 6%), sodium alginate (2%) and polyacrylate ammonia (3%), all in weight, were added to the synthesized α-TCP powder. The samples were molded and evaluated for density, porosity in vitro test (Simulated Body Fluid), crystalline phases and mechanical strength. The results show increased the mechanical properties of the cement when added these polymers.

  3. Wollastonite nanofiber–doped self-setting calcium phosphate bioactive cement for bone tissue regeneration

    Directory of Open Access Journals (Sweden)

    Guo H

    2012-07-01

    Full Text Available Han Guo,1,2 Jie Wei,2 Wenhua Song,2 Shan Zhang,2 Yonggang Yan,3 Changsheng Liu,2 Tiqiao Xiao11Shanghai Synchrotron Radiation Facility, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai, People's Republic of China; 2Key Laboratory for Ultrafine Materials of Ministry of Education, East China University of Science and Technology, Shanghai, People's Republic of China; 3School of Physical Science and Technology, Sichuan University, Chengdu, People's Republic of ChinaAbstract: The purpose of this study was to synthesize a self-setting bioactive cement by incorporation of wollastonite nanofibers (WNFs into calcium phosphate cement (CPC. The composition, morphology, setting time, compressive strength, hydrophilicity, and degradation of WNF-doped CPC (wnf-CPC were investigated. Scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and inductively coupled plasma atomic emission spectroscopy were utilized. Additionally, methyl-thiazolyl-tetrazolium bromide assay, scanning electron microscopy, inductively coupled plasma atomic emission spectroscopy, and histological evaluation were used to study the cell and tissue responses to wnf-CPC, both in vitro and in vivo. The results confirmed that the addition of WNFs into CPC had no obvious effect on the setting time or the compressive strength of wnf-CPC, provided the WNF amount was not more than 10 wt%. However, the hydrophilicity and degradability of wnf-CPC were significantly improved by the addition of WNFs – this was because of the change of microstructure caused by the WNFs. The preferred dissolution of WNFs caused the formation of microporosity in wnf-CPC when soaked in tris hydrochloride solution. The microporosity enlarged the surface area of the wnf-CPC and so promoted degradation of the wnf-CPC when in contact with liquid. In addition, MG-63 cell attachment and proliferation on the wnf-CPC were superior to that on the CPC, indicating that

  4. In vitro osteoblast-like and endothelial cells' response to calcium silicate/calcium phosphate cement

    Energy Technology Data Exchange (ETDEWEB)

    Zhao Qinghui; Qian Jiangchao [State Key Laboratory of Bioreactor Engineering, East China University of Science and Technology, Shanghai 200237 (China); Zhou Huanjun; Yuan Yuan; Mao Yuhao; Liu Changsheng, E-mail: jiangchaoqian@ecust.edu.c, E-mail: csliu@sh163.ne [Engineering Research Center for Biomedical Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China)

    2010-06-01

    This study aims to investigate the interaction between calcium silicate/calcium phosphate cement (CS/CPC) and osteogenesis, in particular the in vitro osteoblast-like and endothelial cells' response to CS/CPC. The effect of CS/CPC on cell attachment, proliferation and differentiation of murine osteoblast-like cell MC3T3-E1, as well as the influence on the cell attachment and proliferation of human umbilical vein endothelial cell (HUVEC), was studied in detail. Our results indicated that CS/CPC exhibited excellent biocompatibility to the osteoblast-like cells. Moreover, the morphology and cytoskeleton organization of MC3T3-E1 cultured on the CS/CPC disks suggested that CS/CPC induced better cell adhesion and cell spreading. Simultaneously, cell proliferation and alkaline phosphatase (ALP) activity of MC3T3-E1 were significantly improved after 3 and 7 days of culture on CS/CPC disks in comparison with CPC disks. Additionally, on CS/CPC disks, HUVEC attached well on day 1 and cell proliferation was also greatly enhanced by day 7. Collectively, these results suggest that the introduction of calcium silicate may improve the cell response involved in the osteogenesis and thus may be beneficial to further modify CPC as a better bone repairing material.

  5. Effects of adding resorbable chitosan microspheres to calcium phosphate cements for bone regeneration

    Energy Technology Data Exchange (ETDEWEB)

    Meng, Dan [Department of Prosthodontics, Beijing Stomatological Hospital, Capital Medical University, Beijing 100050 (China); Dong, Limin [Beijing Key Lab of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Energy Science Building, Beijing 100084 (China); Wen, Ying [Department of Prosthodontics, Beijing Stomatological Hospital, Capital Medical University, Beijing 100050 (China); Xie, Qiufei, E-mail: xieqiuf@163.com [Department of Prosthodontics, Peking University School and Hospital of Stomatology, Beijing 100081 (China)

    2015-02-01

    Calcium phosphate cements (CPCs) have been widely used as bone graft substitutes. However, the undesirable osteoinductivity and slow degradability of CPCs greatly hamper their clinical application. The aim of this study was to synthesize a type of injectable, bioactive cement. This was accomplished by incorporating chitosan microspheres into CPC. CPC containing chitosan microspheres was analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM). XRD showed that the hardened chitosan microsphere/CPC with different proportions of microspheres contained diffraction peaks of hydroxyapatite and chitosan. Compressive strength and dissolution in simulated body fluid were measured. The chitosan microsphere/CPC containing 10% (w/w) chitosan microspheres had a compressive strength of 14.78 ± 0.67 MPa. Cavity defects were created in both femoral condylar regions of New Zealand White rabbits. Chitosan microsphere/CPC (composite group) and α-TCP/CPC (control group) were implanted separately into the bone defects of both femurs. X-ray analysis was performed to observe the filling of these bone defects 3 days after surgery. The extent of bone substitute degradation and new bone formation were evaluated by SEM and histological examination at 8, 16, and 24 weeks after implantation. These results showed far more new bone formation and degradation of the chitosan microsphere/CPC composite in the bone defects. These data indicate that a chitosan microsphere/CPC composite might be considered as a promising injectable material for the generation of new bone tissue. - Highlights: • We synthesized an injectable, bioactive chitosan microsphere/CPC for the first time. • 100–400 μm chitosan microspheres were incorporated into the cement solid phase. • XRD showed the construct contained diffraction peaks of hydroxyapatite and chitosan. • Compressive strength of the composite was about 15 MPa comparable to cancellous bone. • The new construct shows better bone

  6. Effects of adding resorbable chitosan microspheres to calcium phosphate cements for bone regeneration

    International Nuclear Information System (INIS)

    Calcium phosphate cements (CPCs) have been widely used as bone graft substitutes. However, the undesirable osteoinductivity and slow degradability of CPCs greatly hamper their clinical application. The aim of this study was to synthesize a type of injectable, bioactive cement. This was accomplished by incorporating chitosan microspheres into CPC. CPC containing chitosan microspheres was analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM). XRD showed that the hardened chitosan microsphere/CPC with different proportions of microspheres contained diffraction peaks of hydroxyapatite and chitosan. Compressive strength and dissolution in simulated body fluid were measured. The chitosan microsphere/CPC containing 10% (w/w) chitosan microspheres had a compressive strength of 14.78 ± 0.67 MPa. Cavity defects were created in both femoral condylar regions of New Zealand White rabbits. Chitosan microsphere/CPC (composite group) and α-TCP/CPC (control group) were implanted separately into the bone defects of both femurs. X-ray analysis was performed to observe the filling of these bone defects 3 days after surgery. The extent of bone substitute degradation and new bone formation were evaluated by SEM and histological examination at 8, 16, and 24 weeks after implantation. These results showed far more new bone formation and degradation of the chitosan microsphere/CPC composite in the bone defects. These data indicate that a chitosan microsphere/CPC composite might be considered as a promising injectable material for the generation of new bone tissue. - Highlights: • We synthesized an injectable, bioactive chitosan microsphere/CPC for the first time. • 100–400 μm chitosan microspheres were incorporated into the cement solid phase. • XRD showed the construct contained diffraction peaks of hydroxyapatite and chitosan. • Compressive strength of the composite was about 15 MPa comparable to cancellous bone. • The new construct shows better bone

  7. Self-Setting Calcium Phosphate Cements with Tunable Antibiotic Release Rates for Advanced Antimicrobial Applications.

    Science.gov (United States)

    Ghosh, Shreya; Wu, Victoria; Pernal, Sebastian; Uskoković, Vuk

    2016-03-30

    Osteomyelitis, an infectious disease predominantly tied to poor sanitary conditions in underdeveloped regions of the world, is in need of inexpensive, easily in situ synthesizable and administrable materials for its treatment. The results of this study stem from the attempt to create one such affordable and minimally invasive therapeutic platform in the form of a self-setting, injectable cement with a tunable drug release profile, composed of only nanoparticulate hydroxyapatite, the synthetic version of the bone mineral. Cements comprised two separately synthesized hydroxyapatite powders, one of which, HAP2, was precipitated abruptly, retaining the amorphous nature longer, and the other one of which, HAP1, was precipitated at a slower rate, more rapidly transitioning to the crystalline structure. Cements were made with four different weight ratios of the two hydroxyapatite components: 100/0, 85/15, 50/50, and 0/100 with respect to HAP1 and HAP2. Both the setting and the release rates measured on two different antibiotics, vancomycin and ciprofloxacin, were controlled using the weight ratio of the two hydroxyapatite components. Various inorganic powder properties were formerly used to control drug release, but here we demonstrate for the first time that the kinetics of the mechanism of formation of a solid compound can be controlled to produce tunable drug release profiles. Specifically, it was found that the longer the precursor calcium phosphate component of the cement retains the amorphous nature of the primary precipitate, the more active it was in terms of speeding up the diffusional release of the adsorbed drug. The setting rate was, in contrast, inversely proportional to the release rate and to the content of this active hydroxyapatite component, HAP2. The empirical release profiles were fitted to a set of equations that could be used to tune the release rate to the therapeutic occasion. All of the cements loaded with vancomycin or ciprofloxacin inhibited the

  8. In vitro surface reaction layer formation and dissolution of calcium phosphate cement-bioactive glass composites

    Energy Technology Data Exchange (ETDEWEB)

    Liu Changsheng [Key Laboratory for Ultrafine Materials of Ministry of Education, and Engineering Research Center for Biomedical Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China); Chen, C.-W.; Ducheyne, Paul [Center for Bioactive Materials and Tissue Engineering, Department of Bioengineering, University of Pennsylvania, Philadelphia, PA 19104 (United States)], E-mail: liucs@ecust.edu.cn, E-mail: ducheyne@seas.upenn.edu

    2008-09-01

    Composites of hydrated calcium phosphate cement (CPC) and bioactive glass (BG) containing Si were immersed in vitro to study the effect of chemical composition on surface reaction layer formation and dissolution/precipitation behavior. The solutions used were 0.05 M tris hydroxymethyl aminomethane/HCl (tris buffer), tris buffer supplemented with plasma electrolyte (TE) with pH 7.4 at 37 deg. C, and this solution complemented with 10% newborn bovine serum (TES). The post-immersion solutions were analyzed for changes in Ca, PO{sub 4} and Si concentrations. The reacted surfaces were analyzed using Fourier transform infrared (FTIR), and scanning electron microscopy with energy dispersive x-ray analysis. The sample weight variations after immersion were also determined. The results showed that the composition of the bioactive composite CPCs greatly affected their behavior in solution and the formation of apatite bioactive surface reaction layers. After immersion in the TE solution, Ca ions were taken up by all samples during the entire immersion duration. Initially, the P ion concentration increased sharply, and then decreased. This reaction pattern reveals the formation of an amorphous calcium phosphate layer on the surface of these composite CPCs. FTIR revealed that the layer was, in fact, poorly crystallized Ca-deficient carbonate apatite. The thickness of the layer was 12-14 {mu}m and it was composed of rod-like apatite with directional arrangement. For immersion in the TES solution, the Ca and Si ion concentrations showed a similar behavior to that in TE, but the release rate of Si ions was higher. FTIR revealed that after TES immersion, not only did the typical, poorly crystallized, Ca-deficient carbonated apatite form, as it did in TE, but also the serum proteins co-adsorbed on the surface and thereby affected the surface reaction layer formation. A thinner apatite layer was formed and was composed of a micro-porous layer comprising rounded particles in a glue

  9. Injectable calcium phosphate cement and fibrin sealant recombined human bone morphogenetic protein-2 composite in vertebroplasty: an animal study

    OpenAIRE

    Qian, Guang; Dong, Youhai; Yang, Wencheng; Wang, Minghai

    2012-01-01

    Polymethylmethacrylate (PMMA) is currently the most commonly-used material, but it may induce adjacent vertebral fracture due to low degradation and high strength. Our study evaluated the feasibility of injectable calcium phosphate cement (ICPC) and fibrin sealant (FS) as an injectable compound carrier of human bone morphogenetic protein-2 (rhBMP-2) in New Zealand rabbits for vertebroplasty. Results showed ICPC/FS/rhBMP-2 composites induced alkaline phosphatase most effectively at 2 and 4 wee...

  10. Low-pressure plasma treatment of polylactide fibers for enhanced mechanical performance of fiber-reinforced calcium phosphate cements

    OpenAIRE

    Canal Barnils, Cristina; Gallinetti, Sara; Ginebra Molins, Maria Pau

    2014-01-01

    Calcium phosphate cements (CPCs) are extensively used as synthetic bone grafts, but their poor mechanical properties limit their applicability to non-stress-bearing applications. The aim of the present work is to evaluate the potential of plasma surface modification of polylactide (PLA) fibers for reinforcement of CPCs. Oxygen low-pressure plasma was employed at different treatment times and the surface properties of the untreated and plasma-treated PLA were evaluated. Plasma treatment on the...

  11. Porous calcium phosphate-poly (lactic-co-glycolic) acid composite bone cement: A viable tunable drug delivery system.

    Science.gov (United States)

    Roy, Abhijit; Jhunjhunwala, Siddharth; Bayer, Emily; Fedorchak, Morgan; Little, Steve R; Kumta, Prashant N

    2016-02-01

    Calcium phosphate based cements (CPCs) are frequently used as bone void fillers for non-load bearing segmental bone defects due to their clinically relevant handling characteristics and ability to promote natural bone growth. Macroporous CPC scaffolds with interconnected pores are preferred for their ability to degrade faster and enable accelerated bone regeneration. Herein, a composite CPC scaffold is developed using newly developed resorbable calcium phosphate cement (ReCaPP) formulation containing degradable microspheres of bio-compatible poly (lactic-co-glycolic acid) (PLGA) serving as porogen. The present study is aimed at characterizing the effect of in-vitro degradation of PLGA microspheres on the physical, chemical and structural characteristics of the composite cements. The porosity measurements results reveal the formation of highly interconnected macroporous scaffolds after degradation of PLGA microspheres. The in-vitro characterizations also suggest that the degradation by products of PLGA reduces the pH of the local environment thereby increasing the dissolution rate of the cement. In addition, the in-vitro vancomycin release from the composite CPC scaffold suggests that the drug association with the composite scaffolds can be tuned to achieve control release kinetics. Further, the study demonstrates control release lasting for longer than 10weeks from the composite cements in which vancomycin is encapsulated in PLGA microspheres. PMID:26652353

  12. Calcium Phosphate Biomaterials: An Update

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Current calcium phosphate (CaP) biomaterials for bone repair, substitution, augmentation and regeneration include hydroxyapatite ( HA ) from synthetic or biologic origin, beta-tricalcium phosphate ( β-TCP ) , biphasic calcium phosphate (BCP), and are available as granules, porous blocks, components of composites (CaP/polymer) cements, and as coatings on orthopedic and dental implants. Experimental calcium phosphate biomaterials include CO3- and F-substituted apatites, Mg-and Zn-substituted β-TCP, calcium phosphate glasses. This paper is a brief review of the different types of CaP biomaterials and their properties such as bioactivity, osteoconductivity, osteoinductivity.

  13. Cross-linked chitosan improves the mechanical properties of calcium phosphate-chitosan cement.

    Science.gov (United States)

    Aryaei, Ashkan; Liu, Jason; Jayatissa, Ahalapitiya H; Champa Jayasuriya, A

    2015-09-01

    Calcium phosphate (CaP) cements are highly applicable and valuable materials for filling bone defects by minimally invasive procedures. The chitosan (CS) biopolymer is also considered as one of the promising biomaterial candidates in bone tissue engineering. In the present study, some key features of CaP-CS were significantly improved by developing a novel CaP-CS composite. For this purpose, CS was the first cross-linked with tripolyphosphate (TPP) and then mixed with CaP matrix. A group of CaP-CS samples without cross-linking was also prepared. Samples were fabricated and tested based on the known standards. Additionally, the effect of different powder (P) to liquid (L) ratios was also investigated. Both cross-linked and uncross-linked CaP-CS samples showed excellent washout resistance. The most significant effects were observed on Young's modulus and compressive strength in wet condition as well as surface hardness. In dry conditions, the Young's modulus of cross-linked samples was slightly improved. Based on the presented results, cross-linking does not have a significant effect on porosity. As expected, by increasing the P/L ratio of a sample, ductility and injectability were decreased. However, in the most cases, mechanical properties were enhanced. The results have shown that cross-linking can improve the mechanical properties of CaP-CS and hence it can be used for bone tissue engineering applications. PMID:26046262

  14. Enhancement of pedicle screw stability using calcium phosphate cement in osteoporotic vertebrae: in vivo biomechanical study.

    Science.gov (United States)

    Taniwaki, Yoshimichi; Takemasa, Ryuichi; Tani, Toshikazu; Mizobuchi, Hiroo; Yamamoto, Hiroshi

    2003-01-01

    We conducted an experimental study using female beagles with and without ovariectomy-induced osteoporosis to determine the effect of calcium phosphate cement (CPC) on the mechanical stability of inserted pedicle screws. A drill hole was created from the base of the transverse process to the vertebral body; CPC was injected into the hole, and then a screw was inserted into the same hole. In the presence of osteoporosis evidenced by dual X-ray absorptiometry, the stability of the inserted screw augmented by CPC against pull-out and cephalocaudal forces were significantly greater by 28% and 54% at 1 week after operation, 48% and 71% at 2 weeks, and 56% and 68% at 4 weeks compared with those without CPC. The pull-out strength increased progressively with time after surgery, probably reflecting new-bone growth from the surrounding cancellous bone, which was in direct contact with the CPC, as shown in the histologic study. At each time point the cephalocaudal rigidity was similar and the pull-out strength greater than that for the screws inserted without CPC in nonporotic dogs. These findings suggest that CPC augments the stability of the inserted pedicle screws and increases the stiffness of fixed osteoporotic motion segments using instrumentation. PMID:12768486

  15. Influence of artificially-induced porosity on the compressive strength of calcium phosphate bone cements.

    Science.gov (United States)

    Mouzakis, Dionysios; Zaoutsos, Stefanos Polymeros; Bouropoulos, Nikolaos; Rokidi, Stamatia; Papanicolaou, George

    2016-07-01

    The biological and mechanical nature of calcium phosphate cements (CPC's) matches well with that of bone tissues, thus they can be considered as an appropriate environment for bone repair as bone defect fillers. The current study focuses on the experimental characterization of the mechanical properties of CPCs that are favorably used in clinical applications. Aiming on evaluation of their mechanical performance, tests in compression loading were conducted in order to determine the mechanical properties of the material under study. In this context, experimental results occurring from the above mechanical tests on porous specimens that were fabricated from three different porous additives, namely albumin, gelatin and sodium alginate, are provided, while assessment of their mechanical properties in respect to the used porous media is performed. Additionally, samples reinforced with hydroxyapatite crystals were also tested in compression and the results are compared with those of the above tested porous CPCs. The knowledge obtained allows the improvement of their biomechanical properties by controlling their structure in a micro level, and finds a way to compromise between mechanical and biological response. PMID:26945808

  16. Preparation and characterization of a novel strontium-containing calcium phosphate cement with the two-step hydration process.

    Science.gov (United States)

    Yu, Tao; Ye, Jiandong; Wang, Yingjun

    2009-09-01

    A novel Sr-containing calcium phosphate cement (CPC) with excellent compressive strength, good radiopacity and suitable setting time was developed in this work. The two-step hydration reaction resulted in a high compressive strength, with a maximum of up to 74.9MPa. Sr was doped into the calcium-deficient hydroxyapatite as a hydrated product during the hydration reaction of the CPC. Because of the existence of Sr element and the compact microstructure after hydration, the Sr-containing CPC shows good radiopacity. It is expected to be used in orthopedic and maxillofacial surgery for bone defects repairing. PMID:19380262

  17. Calcium phosphate cement delivering zoledronate decreases bone turnover rate and restores bone architecture in ovariectomized rats

    International Nuclear Information System (INIS)

    Patients sustaining bony fractures frequently require the application of bone graft substitutes to fill the bone defects. In the meantime, anti-osteoporosis drugs may be added in bone fillers to treat osteoporosis, especially in postmenopausal women and the elderly. The effects of zoledronate-impregnated calcium phosphate cement (ZLN/CPC) on ovariectomized (OVX) rats were evaluated. OVX rats were implanted with ZLN/CPC, containing 0.025 mg ZLN in the greater omentum. Afterward the clinical sign of toxicity was recorded for eight weeks. The rats were sacrificed and blood samples were collected for hematology and serum bone turnover markers analyses. The four limbs of the rats were harvested and micro-computer tomography (micro-CT) scanning and bone ash analyses were performed. No clinical toxicity was observed in the treated rats. Compared to the OVX rats, levels of bone resorption markers (fragments of C-telopeptides of type I collagen) and bone formation markers (alkaline phosphatase and osteocalcin) decreased significantly in the treated rats. Osteopontin, which mediates the anchoring of osteoclasts to the mineral matrix of bones, also decreased significantly. Micro-CT scanning and histologic examinations of the distal femoral metaphyses showed that the cancellous bone architectures were restored, with a concomitant decrease in bone porosity. The bone mineral content in the bone ashes also increased significantly. This study indicates that ZLN-impregnated CPC reduces bone turnover rate and restores bone architecture in OVX rats. CPC may be an appropriate carrier to deliver drugs to treat osteoporosis, and this approach may also reduce rates of post-dosing symptoms for intravenous ZLN delivery. (paper)

  18. Vascularization of plastic calcium phosphate cement in vivo induced by in-situ-generated hollow channels.

    Science.gov (United States)

    Yu, Tao; Dong, Chao; Shen, Zhonghua; Chen, Yan; Yu, Bo; Shi, Haishan; Zhou, Changren; Ye, Jiandong

    2016-11-01

    Despite calcium phosphate cement (CPC) is promising for bone repair therapy, slow biodegradation and insufficient vascularization in constructs negatively impacts its clinical application. A self-setting CPC composited with gelatin fiber is investigated to test the utility of this tissue engineering strategy to support rapid and extensive vascularization process. The interconnected hollow channels in CPC are formed after dissolution of gelatin fibers in vivo. The CPC-gelatin samples exhibit relatively decent/enhanced mechanical property, compared to the control. When implanted in vivo, the pre-established vascular networks in material anastomose with host vessels and accelerate vascular infiltration throughout the whole tissue construct. Different channel sizes induce different vascularization behaviors in vivo. Results indicate that the channel with the size of 250μm increases the expression of the representative angiogenic factors HIF1α, PLGF and migration factor CXCR4, which benefit the formation of small vessels. On the other hand, the channel with the size of 500μm enhances VEGF-A expression, which benefit the development of large vessels. Notably, the intersection area of channels has high invasive, sprouting and vasculogenesis potential under hypoxic condition, because more HIF1α-positive cells are observed there. Observation of the CD31-positive lumen in the border of scaffold indicates the ingrowth of blood vessels from its host into material through channel, benefited from gradually increased HIF1α expression. This kind of material was suggested to promote the effective application of bone regeneration through the combination of in situ self-setting, plasticity, angiogenesis, and osteoconductivity. PMID:27524007

  19. The biological performance of injectable calcium phosphate/PLGA cement in osteoporotic rats

    International Nuclear Information System (INIS)

    Calcium phosphate cements (CPCs) including poly(D,L-lactic-co-glycolic) acid (PLGA) microparticles are promising candidates for bone regenerative applications. Previous studies with CPC/PLGA demonstrated that the material is non-toxic, biocompatible and osteoconductive. However, the outcome of these studies was based on healthy individuals and consequently does not provide information on bone substitute material performance in a compromised situation, such as osteoporosis. Therefore, this study comparatively evaluated the performance of injectable CPC/PLGA in healthy (SHAM) and osteoporotic rats (OVX) using a rat femoral condyle defect with implantation periods of 4 and 12 weeks. It was hypothesized that in OVX rats the degradation of CPC/PLGA would increase due to a higher osteoclastic activity present in osteoporotic animals and that the obtained space would be rapidly filled with newly formed bone. The results revealed an accelerated degradation of the used CPC/PLGA in osteoporotic animals, but bone formation was less compared to that in healthy animals at 4 and 12 weeks after implantation. In addition, after 4 weeks, the amount of newly formed bone under osteoporotic conditions was less in the femoral condyle defect compared to that present in a non-defect, osteoporotic control femoral condyle, but equal after 12 weeks. On the other hand, in healthy animals, the amount of newly formed bone in the femoral condyle defect was equal to that present in a non-defect control femoral condyle at 4 weeks, while higher after 12 weeks. This indicates that bone regeneration at a defect site under osteoporotic conditions is slower, but can reach native amounts after longer time periods. Consequently, bone regenerative treatments under osteoporotic conditions seem to require additional empowerment of bone substitute materials. (paper)

  20. Induced Pluripotent Stem Cell-derived Mesenchymal Stem Cell Seeding on Biofunctionalized Calcium Phosphate Cements

    Institute of Scientific and Technical Information of China (English)

    WahWah TheinHan; Jun Liu; Minghui Tang; Wenchuan Chen; Linzhao Cheng; Hockin H. K. Xu

    2013-01-01

    Induced pluripotent stem cells (iPSCs) have great potential due to their proliferation and differentiation capability. The objectives of this study were to generate iPSC-derived mesenchymal stem cells (iPSC-MSCs), and investigate iPSC-MSC proliferation and osteogenic differentiation on calcium phosphate cement (CPC) containing biofunctional agents for the first time. Human iPSCs were derived from marrow CD34+ cells which were reprogrammed by a single episomal vector. iPSCs were cultured to form embryoid bodies (EBs), and MSCs migrated out of EBs. Five biofunctional agents were incorporated into CPC:RGD (Arg-Gly-Asp) peptides, fibronectin (Fn), fibronectin-like engineered polymer protein (FEPP), extracellular matrix Geltrex, and platelet concentrate. iPSC-MSCs were seeded on five biofunctionalized CPCs:CPC-RGD, CPC-Fn, CPC-FEPP, CPC-Geltrex, and CPC-Platelets. iPSC-MSCs on biofunctional CPCs had enhanced proliferation, actin fiber expression, osteogenic differentiation and mineralization, compared to control. Cell proliferation was greatly increased on biofunctional CPCs. iPSC-MSCs underwent osteogenic differentiation with increased alkaline phosphatase, Runx2 and collagen-I expressions. Mineral synthesis by iPSC-MSCs on CPC-Platelets was 3-fold that of CPC control. In conclusion, iPSCs showed high potential for bone engineering. iPSC-MSCs on biofunctionalized CPCs had cell proliferation and bone mineralization that were much better than traditional CPC. iPSC-MSC-CPC constructs are promising to promote bone regeneration in craniofacial/orthopedic repairs.

  1. Effect of Additives on the Morphology of the Hydrated Product and Physical Properties of a Calcium Phosphate Cement

    Institute of Scientific and Technical Information of China (English)

    Xiupeng WANG; Jiandong YE; Yingjun WANG

    2008-01-01

    The morphology of a hydrated calcium phosphate cement (CPC) doped with several normally used additives was investigated by scanning electron microscopy (SEM) and the compressive strength of the cement was determined in this study. The hydrated products of CPC without additives was rod-like hydroxyapatite (HA) grains with around 2-5 μm in length and 100 nm in width. The addition of Sr obviously decreased the crystal size of the rod-like grains. CPCs containing carbonate, collagen and gelatin showed flake-like crystal morphology. Crylic acid-containing CPC presented flocculus-like structure. And malic acid-containing CPC exhibited oriented flake-like structure. The X-ray diffraction (XRD) analysis showed that the additives used in this study did not alter the hydration products of the cement. The compressive strength tests indicated that the compressive strength of the cement with rod-like morphology HA crystals was much higher than that of the cement with flake-like morphology HA crystals, and the cement with oriented flake-like morphology HA crystals .exhibited the poorest compressive strength.

  2. Fluoride-containing nanoporous calcium-silicate MTA cements for endodontics and oral surgery: Early fluorapatite formation in a phosphate-containing solution

    OpenAIRE

    Gandolfi, M.G.; Taddei, P.; Siboni, F.; Modena, E.; Ginebra Molins, Maria Pau; Prati, Claudio

    2011-01-01

    Gandolfi MG, Taddei P, Siboni F, Modena E, Ginebra MP, Prati C. Fluoride-containing nanoporous calcium-silicate MTA cements for endodontics and oral surgery: early fluorapatite formation in a phosphate-containing solution. International Endodontic Journal, 44, 938–949, 2011. Aim To test the chemical–physical properties and apatite-forming ability of experimental fluoride-doped calcium silicate cements designed to create novel bioactive materials for use in endodontics ...

  3. Combined Percutaneous Iliosacral Screw Fixation With Sacroplasty Using Resorbable Calcium Phosphate Cement for Osteoporotic Pelvic Fractures Requiring Surgery.

    Science.gov (United States)

    Collinge, Cory A; Crist, Brett D

    2016-06-01

    Osteoporotic sacral fractures, including acute and chronic insufficiency fractures, are increasing in frequency and present a number of management problem. Many of these patients are treated nonoperatively with relative immobility (eg, bedrest, wheelchair, or weight-bearing restrictions) and analgesics, which likely make the osteoporotic component worse. Surgery in this patient population may be desirable in some cases with the goals of improving mobility, relieving pain, and healing in an aligned position while minimizing deformity progression. However, internal fixation of the osteoporotic pelvis can be difficult. Large unicortical lag screws are the workhorse of posterior pelvic fixation, and yet fixation in cancellous bone corridors of an osteoporotic sacrum seems unlikely to achieve optimal fixation. As a result, the operative management and clinical results of these difficult injuries may not be uniformly successful. The authors present a technique for treating osteoporotic patients with a sacral fracture when operative treatment is indicated using percutaneous screw fixation combined with screw augmentation using a resorbable calcium phosphate bone substitute or "cement." The guide wire for a 7.3-mm or other large cannulated lag screw is fully inserted along the desired bony sacral corridor as is standard. The lag screw is then inserted over the wire to the depth where cement is desired. The guide wire is removed, and the aqueous calcium phosphate is injected through the screw's cannulation. For acute fractures, cement was applied to the areas distant to the fracture; whereas in insufficiency fractures, the cement was inserted along most of the screw path. The guide wire then can be reinserted and the lag screw fully inserted. The rationale for using these 2 modalities is their synergistic effect: the cannulated screw provides typical screw fixation and also a conduit for cement application. The cement augments the lag screw's purchase in osteoporotic bone

  4. Different Angiogenic Abilities of Self-Setting Calcium Phosphate Cement Scaffolds Consisting of Different Proportions of Fibrin Glue

    OpenAIRE

    Jintao Xiu; Junjun Fan; Jie Li; Geng Cui; Wei Lei

    2014-01-01

    To investigate the different angiogenic abilities of the self-setting calcium phosphate cement (CPC) consisting of different proportions of fibrin glue (FG), the CPC powder and the FG solution were mixed at the powder/liquid (P/L) ratios of 1 : 0.5, 1 : 1, and 1 : 2 (g/mL), respectively, and pure CPC was used as a control. After being implanted into the lumbar dorsal fascia of the rabbit, the angiogenic process was evaluated by histological examination and CD31 immunohistochemistry to detect ...

  5. Production and characterization of setting hydraulic cements based on calcium phosphate; Obtencao e caracterizacao de cimentos de fosfato de calcio de pega hidraulica

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Luci C. de; Rigo, Eliana C.S.; Santos, Luis A dos; Boschi, Anselmo Ortega [Sao Carlos Univ., SP (Brazil). Dept. de Engenharia de Materiais; Carrodeguas, Raul G. [Universidad de La Habana, Habana (Cuba). Centro de Biomateriales

    1997-12-31

    Setting hydraulic cements based on calcium phosphate has risen great interest in scientific literature during recent years due to their total bio compatibility and to the fact that they harden `in situ`, providing easy handling and adaptation to the shape and dimensions of the defect which requires correction, differently from the predecessors, the calcium phosphate ceramics (Hydroxy apatite, {beta}-tri calcium phosphate, biphasic, etc) in the shape of dense or porous blocks and grains. In the work, three calcium-phosphate cement compositions were studied. The resulting compositions were characterized according to the following aspects: setting times, pH, mechanical resistance, crystalline phases, microstructure and solubility in SBF (Simulated Body Fluid). The results show a potential use for the compositions. (author) 6 figs., 4 tabs.

  6. Local treatment of osteoporosis with alendronate-loaded calcium phosphate cement

    Institute of Scientific and Technical Information of China (English)

    Zhao Jindong; Tang Hai; Wang Jiayang; Li Gang

    2014-01-01

    Background A new treatment strategy is to target specific areas of the skeletal system that are prone to clinically significant osteoporotic fractures.We term this strategy as the "local treatment of osteoporosis".The study was performed to investigate the effect of alendronate-loaded calcium phosphate cement (CPC) as a novel drug delivery system for local treatment of osteoorosis.Methods An in vitro study was performed using CPC fabricated with different concentrations of alendronate (ALE,0,2,5,10 weight percent (wt%)).The microstructure,setting time,infrared spectrum,biomechanics,drug release,and biocompatibility of the composite were measured in order to detect changes when mixing CPC with ALE.An in vivo study was also performed using 30 Sprague-Dawley rats randomly divided into six groups:normal,Sham (ovariectomized (OVX) + Sham),CPC with 2% ALE,5%ALE,and 10% ALE groups.At 4 months after the implantation of the composite,animals were sacrificed and the caudal vertebrae (levels 4-7) were harvested for micro-CT examination and biomechanical testing.Results The setting time and strength of CPC was significantly faster and greater than the other groups.The ALE release was sustained over 21 days,and the composite showed good biocompatibility.In micro-CT analysis,compared with the Sham group,there was a significant increase with regard to volumetric bone mineral density (BMD) and trabecular number (Tb.N) in the treated groups (P <0.05).Trabecular spacing (Tb.Sp) showed a significant increase in the Sham group compared to other groups (P <0.01).However,trabecular thickness (Tb.Th) showed no significant difference among the groups.In biomechanical testing,the maximum compression strength and stiffness of trabecular bone in the Sham group were lower than those in the experimental groups.Conclusions The ALE-loaded CPC displayed satisfactory properties in vitro,which can reverse the OVX rat vertebral trabecular bone microarchitecture and biomechanical

  7. Healing of segmental ulnar defects in dog using bioresorbable calcium phosphate cement added with recombinant human bone morphogenetic protein-2

    Energy Technology Data Exchange (ETDEWEB)

    Ohura, K.; Hamanishi, C. [Kinki Univ. School of Medicine, Osaka (Japan). Dept. of Orthopaedic Surgery; Irie, H. [Olympus Optical Co., Ltd., Tokyo (Japan)

    2001-07-01

    Bioresorbable calcium phosphate cement (BCPC) cylinders soaked with 100 {mu}g of rhBMP-2 were implanted into 21 mm segmental ulnar defects in dogs. New bone induced around cylinders united both bone segments in 3 weeks. As the cylinder dissolved, the induced bone was remodeled into the compact bone by 9 weeks. However, the cement cylinder implanted without BMP did not dissolve and that defect did not recover bone continuity in 9 weeks. Mechanical test at 9 weeks showed that the BMP group achieved 71% union and 63% of bone strength compared to normal ulna. However, other two groups, the implantation of the cylinder alone and no implantation, did not unite any case. The implantation of thin cylinders of BCPC soaked with small amount of rhBMP-2 repaired large bone defects of high mammal fast. Added with more BMP, it will be possible to apply this biocompatible composite even in clinical cases. (orig.)

  8. Stimulation of Odontogenesis and Angiogenesis via Bioactive Nanocomposite Calcium Phosphate Cements Through Integrin and VEGF Signaling Pathways.

    Science.gov (United States)

    Lee, Sang-Im; Lee, Eui-Suk; El-Fiqi, Ahmed; Lee, So-Youn; Eun-Cheol Kim; Kim, Hae-Won

    2016-05-01

    Formulating self-setting calcium phosphate cements (CPCs) with secondary phases particularly in the nanoscale order holds great promise to improve biological properties. Here, we focus on the effect that bioactive glass nanoparticles (BGN) incorporated in CPC compositions can have on the proliferation, odontogenic differentiation, and angiogenic stimulation of stem cells derived from human dental pulp (HDPSCs). These odontogenic and angiogenic events are of special importance in the dentin-pulp regeneration processes. In comparison to pure CPCs, nanocomposite cements exhibit a significantly improved proliferation of HDPSCs, and the improvement is more significant as the BGN content increases. The nanocomposite cements substantially enhance the adhesion of cells, and significantly up-regulate odontogenic differentiation, including alkaline phosphatase (ALP) activity and the expressions of odontogenic genes (sialophosphoprotein, dentin matrix protein I, ALP, osteopontin and osteocalcin). Furthermore, the use of nanocomposite cements result in stimulation of angiogenic gene expression (VEGF, FGF-2, VEGFRs, PECAM-1, and VE-cadherin) and protein production (VEGF, VEGFR-1). The angiogenic stimulation by the HDPSCs significantly affects the endothelial cell behaviors, that is, the endothelial cell migration and the tubular network formation are substantially improved when treated with HDPSC-conditioned medium, particularly with the help of nanocomposite cements. The integrin and VEGF signaling pathways are reasoned for the stimulation of the odontogenesis and angiogenesis of cells, where the nanocomposite cements up-regulate the integrin subsets α1, α2, α3, and β1, and activate the integrin downstream signal pathways, such as p-FAK, p-Akt, p-paxillin, JNK, EK, and NF-κB, as well as other nuclear transcriptional factors, including CREB, STAT-3, and ELK-1. The current results indicate that the new formulation of the nanocomposite self-setting cements might provide some

  9. Effect of curing conditions on the dimensional and thermal stability of calcium phosphate cement for elevated temperature applications

    International Nuclear Information System (INIS)

    Calcium phosphate cements (CPCs) are attractive materials for elevated temperature applications, like moulds to process thermoplastics up to 300 °C. The CPC resulting from the reaction of wollastonite with phosphoric acid cured at room temperature however contains hydrated phases like brushite, and is thus not stable when exposed to temperatures above 200 °C. A non-contact method based on digital image correlation demonstrated that isothermal curing at 60 °C reduces the thermal shrinkage up to 300 °C by 25%. This curing method results in the direct formation of the more stable monetite in a shorter curing time. The correlated results of TGA, pH of the filtration water, and DSC analysis on partially cured material indicate this. XRD diffractograms and SEM images in combination with EDX show the evolution of the transformation of wollastonite into monetite, and the structure and morphology of the formed material

  10. Effect of curing conditions on the dimensional and thermal stability of calcium phosphate cement for elevated temperature applications

    Energy Technology Data Exchange (ETDEWEB)

    Blom, Johan [Vrije Universiteit Brussel, Department of Mechanics of Materials and Constructions, Pleinlaan 2, Brussels 1050 (Belgium); Rahier, Hubert [Vrije Universiteit Brussel, Research Group of Physical Chemistry and Polymer Sciences, Pleinlaan 2, Brussels 1050 (Belgium); Wastiels, Jan, E-mail: Jan.Wastiels@vub.ac.be [Vrije Universiteit Brussel, Department of Mechanics of Materials and Constructions, Pleinlaan 2, Brussels 1050 (Belgium)

    2014-12-15

    Calcium phosphate cements (CPCs) are attractive materials for elevated temperature applications, like moulds to process thermoplastics up to 300 °C. The CPC resulting from the reaction of wollastonite with phosphoric acid cured at room temperature however contains hydrated phases like brushite, and is thus not stable when exposed to temperatures above 200 °C. A non-contact method based on digital image correlation demonstrated that isothermal curing at 60 °C reduces the thermal shrinkage up to 300 °C by 25%. This curing method results in the direct formation of the more stable monetite in a shorter curing time. The correlated results of TGA, pH of the filtration water, and DSC analysis on partially cured material indicate this. XRD diffractograms and SEM images in combination with EDX show the evolution of the transformation of wollastonite into monetite, and the structure and morphology of the formed material.

  11. Bone healing response to an injectable calcium phosphate cement with enhanced radiopacity.

    Science.gov (United States)

    Acarturk, Oguz; Lehmicke, Michael; Aberman, Harold; Toms, Derek; Hollinger, Jeffrey O; Fulmer, Mark

    2008-07-01

    The aim of this study was to determine the impact of barium sulfate on remodeling and regeneration in standard tibial defects in rabbits treated with the Norian skeletal repair system (SRS). Two formulations of SRS (with and without barium sulfate) were injected into the medullary canal of the tibia of New Zealand white rabbits. Animals were sacrificed at 6 weeks, 6 months, 1 year, and 2 years. Over the 2-year duration of the study, standard SRS and SRS with barium sulfate appeared to be biocompatible and osteoconductive with no evidence of either inflammation or fibrous tissue around the implant materials or at the bone-material interfaces. This outcome underscores the osteophilic property of the SRS. A difference we observed between the standard SRS and the SRS with barium sulfate was the appearance of acellular material contiguous to the SRS with barium sulfate. Energy dispersive X-ray spectroscopy (EDX) analysis was conducted and confirmed that the acellular material was barium sulfate. Pathological examination of additional tissues including regional lymph nodes revealed neither dissemination of calcium phosphate nor barium sulfate. We concluded that the residual barium sulfate detected by EDX was localized to the intramedullary canal of the tibia. PMID:18098201

  12. The mechanical and biological studies of calcium phosphate cement-fibrin glue for bone reconstruction of rabbit femoral defects

    Directory of Open Access Journals (Sweden)

    Dong J

    2013-03-01

    Full Text Available Jingjing Dong,1,* Geng Cui,2,* Long Bi,1,* Jie Li,3 Wei Lei11Institute of Orthopedics, Xijing Hospital, Fourth Military Medical University, Xi’an, Shaanxi, People’s Republic of China; 2Institute of Orthopedics, General Hospital of PLA, Beijing, People’s Republic of China; 3Institute of Gynecology and Obstetrics, General Hospital of PLA, Beijing, People’s Republic of China*These authors contributed equally to this workAbstract: In order to improve the mechanical and biological properties of calcium phosphate cement (CPC, nanometer-biomaterial for bone reconstruction in the rabbit femoral defect model, fibrin glue (FG, the natural product, purified from the blood was introduced at three different ratios. The CPC powder and the FG solution were mixed, respectively, at the powder/liquid (P/L ratios (g/mL of 1:1, 3:1, and 5:1 (g/mL, and pure CPC was used as a control. After being implanted into the femoral defect in rabbit, the healing process was evaluated by micro-computed tomography scan, biomechanical testing, and histological examination. By micro-computed tomography analysis, the P/L ratio of 1:1 (g/mL group indicated the largest quantity of new bone formation at 4 weeks, 8 weeks, and 12 weeks after implantation, respectively. Bone volume per trabecular volume of the 1:1 group was highest in the four groups, which was 1.45% ± 0.42%, 7.35% ± 1.45%, and 29.10% ± 1.67% at 4 weeks, 8 weeks, and 12 weeks after the operation, respectively. In the biomechanical tests, the compressive strength and the elastic modulus of the three CPC–FG groups were much higher than those of the pure CPC group at the determined time point (P < 0.05. The histological evaluation also showed the best osseointegration in the 1:1 group at 4 weeks, 8 weeks, and 12 weeks after the operation, respectively. In the 1:1 group, the bone grew into the pore of the cement in the laminar arrangement and connected with the cement tightly at the 12th week after the operation

  13. Whisker-reinforced bioactive composites containing calcium phosphate cement fillers: effects of filler ratio and surface treatments on mechanical properties.

    Science.gov (United States)

    Xu, H H; Quinn, J B

    2001-11-01

    Calcium phosphate cement (CPC) sets to form microporous solid hydroxyapatite with excellent osteoconductivity, but its brittleness and low strength prohibit use in stress-bearing locations. The aim of this study was to incorporate prehardened CPC particles and ceramic whiskers in a resin matrix to improve the strength and fracture resistance, and to investigate the effects of key microstructural variables on composite mechanical properties. Two types of whiskers were used: silicon nitride, and silicon carbide. The whiskers were surface-treated by fusing with silica and by silanization. The CPC particle fillers were either silanized or not silanized. Seven mass ratios of whisker-silica/CPC were mixed: 0:1 (no whisker-silica), 1:5, 1:2, 1:1, 2:1, 5:1, and 1:0 (no CPC). Each powder was blended with a bisphenol-a-glycidyl methacrylate-based resin to harden in 2 x 2 x 25 mm molds by two-part chemical curing. The specimens were tested in three-point flexure to measure strength, work-of-fracture (toughness), and elastic modulus. Two-way analysis of variance was used to analyze the data, and scanning electron microscopy was used to examine specimen fracture surfaces. The whisker-silica/CPC ratio had significant effects on composite properties (p particles without whiskers. The composite properties were determined by whisker-to-CPC ratio and filler surface treatments. PMID:11484178

  14. Different Angiogenic Abilities of Self-Setting Calcium Phosphate Cement Scaffolds Consisting of Different Proportions of Fibrin Glue

    Directory of Open Access Journals (Sweden)

    Jintao Xiu

    2014-01-01

    Full Text Available To investigate the different angiogenic abilities of the self-setting calcium phosphate cement (CPC consisting of different proportions of fibrin glue (FG, the CPC powder and the FG solution were mixed at the powder/liquid (P/L ratios of 1 : 0.5, 1 : 1, and 1 : 2 (g/mL, respectively, and pure CPC was used as a control. After being implanted into the lumbar dorsal fascia of the rabbit, the angiogenic process was evaluated by histological examination and CD31 immunohistochemistry to detect the new blood vessels. The result of the new blood vessel showed that the P/L ratio of 1 : 1 group indicated the largest quantity of new blood vessel at 4 weeks, 8 weeks, and 12 weeks after implantation, respectively. The histological evaluation also showed the best vascular morphology in the 1 : 1 group at 4 weeks, 8 weeks, and 12 weeks after the operation, respectively. Our study indicated that the CPC-FG composite scaffold at the P/L ratio of 1 : 1  (g/mL stimulated angiopoiesis better than any other P/L ratios and has significant potential as the bioactive material for the treatment of bone defects.

  15. Enhanced healing of rabbit segmental radius defects with surface-coated calcium phosphate cement/bone morphogenetic protein-2 scaffolds

    International Nuclear Information System (INIS)

    Large osseous defects remain a difficult clinical problem in orthopedic surgery owing to the limited effective therapeutic options, and bone morphogenetic protein-2 (BMP-2) is useful for its potent osteoinductive properties in bone regeneration. Here we build a strategy to achieve prolonged duration time and help inducting new bone formation by using water-soluble polymers as a protective film. In this study, calcium phosphate cement (CPC) scaffolds were prepared as the matrix and combined with sodium carboxymethyl cellulose (CMC-Na), hydroxypropylmethyl cellulose (HPMC), and polyvinyl alcohol (PVA) respectively to protect from the digestion of rhBMP-2. After being implanted in the mouse thigh muscles, the surface-modified composite scaffolds evidently induced ectopic bone formation. In addition, we further evaluated the in vivo effects of surface-modified scaffolds in a rabbit radius critical defect by radiography, three dimensional micro-computed tomographic (μCT) imaging, synchrotron radiation-based micro-computed tomographic (SRμCT) imaging, histological analysis, and biomechanical measurement. The HPMC-modified CPC scaffold was regarded as the best combination for segmental bone regeneration in rabbit radius. - Highlights: • A simple surface-coating method was used to fabricate composite scaffolds. • Growth factor was protected from rapid depletion via superficial coating. • Significant promotion of bone regeneration was achieved. • HPMC-modification displayed optimal effect of bone regeneration

  16. In vitro study of using calcium phosphate cement as immunoisolative device to enclose insulinoma/agarose microspheres as bioartificial pancreas.

    Science.gov (United States)

    Kai-Chiang, Yang; Ching-Yao, Yang; Chang-Chin, Wu; Tzong-Fu, Kuo; Feng-Huei, Lin

    2007-12-15

    In this study, the feasibility of using calcium phosphate cement (CPC) as immunoisolative device to enclose insulinoma/agarose microspheres as bioartificial pancreas was evaluated. We fabricated a chamber by CPC and utilized X-ray diffraction, Scanning electron microscope and Mercury intrusion porosimetry to identify the characters of the CPC chamber. The nominal molecular weight cut-off and cytotoxicity of CPC chamber were also evaluated. An insulinoma cell line (RIN-m5F) was chosen as insulin source and encapsulated in agarose microspheres and then enclosed in preformed CPC chamber. Insulin secretion was analyzed by Enzyme-linked immunosorbant assay to evaluate the function of insulinoma enclosed in CPC chamber. Results showed that the CPC chamber was non-cytotoxicity to insulinoma and can block the penetration of molecules which molecular weight larger than 12.4 kDa. Insulinoma inside the CPC chamber can secrete insulin in stable level for 30 days. This study indicated that we may use CPC as immunoisolative material to enclose insulinoma/agarose microspheres as bioartificial pancreas. PMID:17514757

  17. Enhanced healing of rabbit segmental radius defects with surface-coated calcium phosphate cement/bone morphogenetic protein-2 scaffolds

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Yi; Hou, Juan; Yin, ManLi [Engineering Research Center for Biomedical Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China); Wang, Jing, E-mail: biomatwj@163.com [Engineering Research Center for Biomedical Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China); Liu, ChangSheng, E-mail: csliu@sh163.net [Engineering Research Center for Biomedical Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China); The State Key Laboratory of Bioreactor Engineering, East China University of Science and Technology, Shanghai 200237 (China); Key Laboratory for Ultrafine Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China)

    2014-11-01

    Large osseous defects remain a difficult clinical problem in orthopedic surgery owing to the limited effective therapeutic options, and bone morphogenetic protein-2 (BMP-2) is useful for its potent osteoinductive properties in bone regeneration. Here we build a strategy to achieve prolonged duration time and help inducting new bone formation by using water-soluble polymers as a protective film. In this study, calcium phosphate cement (CPC) scaffolds were prepared as the matrix and combined with sodium carboxymethyl cellulose (CMC-Na), hydroxypropylmethyl cellulose (HPMC), and polyvinyl alcohol (PVA) respectively to protect from the digestion of rhBMP-2. After being implanted in the mouse thigh muscles, the surface-modified composite scaffolds evidently induced ectopic bone formation. In addition, we further evaluated the in vivo effects of surface-modified scaffolds in a rabbit radius critical defect by radiography, three dimensional micro-computed tomographic (μCT) imaging, synchrotron radiation-based micro-computed tomographic (SRμCT) imaging, histological analysis, and biomechanical measurement. The HPMC-modified CPC scaffold was regarded as the best combination for segmental bone regeneration in rabbit radius. - Highlights: • A simple surface-coating method was used to fabricate composite scaffolds. • Growth factor was protected from rapid depletion via superficial coating. • Significant promotion of bone regeneration was achieved. • HPMC-modification displayed optimal effect of bone regeneration.

  18. Using calcium silicate to regulate the physicochemical and biological properties when using β-tricalcium phosphate as bone cement

    International Nuclear Information System (INIS)

    β-Tricalcium phosphate (β-TCP) is an osteoconductive material. For this research we have combined it with a low degradation calcium silicate (CS) to enhance its bioactive and osteostimulative properties. To check its effectiveness, a series of β-TCP/CS composites with different ratios were prepared to make new bioactive and biodegradable biocomposites for bone repair. Regarding the formation of bone-like apatite, the diametral tensile strength as well as the ion release and weight loss of composites were compared both before and after immersions in simulated body fluid (SBF). In addition, we also examined the behavior of human dental pulp cells (hDPCs) cultured on β-TCP/CS composites. The results show that the apatite deposition ability of the β-TCP/CS composites improves as the CS content is increased. For composites with more than a 60% CS content, the samples become completely covered by a dense bone-like apatite layer. At the end of the immersion period, weight losses of 24%, 32%, 34%, 38%, 41%, and 45% were observed for the composites containing 0%, 20%, 40%, 80%, 80% and 100% β-TCP cements, respectively. In addition, the antibacterial activity of CS/β-TCP composite improves as the CS-content is increased. In vitro cell experiments show that the CS-rich composites promote human dental pulp cell (hDPC) proliferation and differentiation. However, when the CS quantity in the composite is less than 60%, the quantity of cells and osteogenesis protein of hDPCs is stimulated by Si released from the β-TCP/CS composites. The degradation of β-TCP and the osteogenesis of CS give strong reason to believe that these calcium-based composite cements will prove to be effective bone repair materials. - Highlights: • CS improved the physicochemical properties and osteogenic activity of β-TCP. • Higher CS in the composite, the shorter setting time and the higher DTS was found. • With a CS more than 40%, the osteogenesis and angiogenesis proteins were promoted by

  19. Using calcium silicate to regulate the physicochemical and biological properties when using β-tricalcium phosphate as bone cement

    Energy Technology Data Exchange (ETDEWEB)

    Kao, Chia-Tze; Huang, Tsui-Hsien [School of Dentistry, Chung Shan Medical University, Taichung, Taiwan (China); Department of Dentistry, Chung Shan Medical University Hospital, Taichung, Taiwan (China); Chen, Yi-Jyun [School of Dentistry, Chung Shan Medical University, Taichung, Taiwan (China); Department of Dentistry, Chung Shan Medical University Hospital, Taichung, Taiwan (China); Dental Department, Taichung Hospital, Ministry of Health and Welfare, Taichung City, Taiwan (China); Hung, Chi-Jr [School of Dentistry, Chung Shan Medical University, Taichung, Taiwan (China); Department of Dentistry, Chung Shan Medical University Hospital, Taichung, Taiwan (China); Lin, Chi-Chang, E-mail: chichang31@gmail.com [Department of Chemical and Materials Engineering, Tunghai University, Taichung, Taiwan (China); Shie, Ming-You, E-mail: eviltacasi@gmail.com [Department of Chemical and Materials Engineering, Tunghai University, Taichung, Taiwan (China)

    2014-10-01

    β-Tricalcium phosphate (β-TCP) is an osteoconductive material. For this research we have combined it with a low degradation calcium silicate (CS) to enhance its bioactive and osteostimulative properties. To check its effectiveness, a series of β-TCP/CS composites with different ratios were prepared to make new bioactive and biodegradable biocomposites for bone repair. Regarding the formation of bone-like apatite, the diametral tensile strength as well as the ion release and weight loss of composites were compared both before and after immersions in simulated body fluid (SBF). In addition, we also examined the behavior of human dental pulp cells (hDPCs) cultured on β-TCP/CS composites. The results show that the apatite deposition ability of the β-TCP/CS composites improves as the CS content is increased. For composites with more than a 60% CS content, the samples become completely covered by a dense bone-like apatite layer. At the end of the immersion period, weight losses of 24%, 32%, 34%, 38%, 41%, and 45% were observed for the composites containing 0%, 20%, 40%, 80%, 80% and 100% β-TCP cements, respectively. In addition, the antibacterial activity of CS/β-TCP composite improves as the CS-content is increased. In vitro cell experiments show that the CS-rich composites promote human dental pulp cell (hDPC) proliferation and differentiation. However, when the CS quantity in the composite is less than 60%, the quantity of cells and osteogenesis protein of hDPCs is stimulated by Si released from the β-TCP/CS composites. The degradation of β-TCP and the osteogenesis of CS give strong reason to believe that these calcium-based composite cements will prove to be effective bone repair materials. - Highlights: • CS improved the physicochemical properties and osteogenic activity of β-TCP. • Higher CS in the composite, the shorter setting time and the higher DTS was found. • With a CS more than 40%, the osteogenesis and angiogenesis proteins were promoted by

  20. Application of Calcium Phosphate Materials in Dentistry

    Directory of Open Access Journals (Sweden)

    Jabr S. Al-Sanabani

    2013-01-01

    Full Text Available Calcium phosphate materials are similar to bone in composition and in having bioactive and osteoconductive properties. Calcium phosphate materials in different forms, as cements, composites, and coatings, are used in many medical and dental applications. This paper reviews the applications of these materials in dentistry. It presents a brief history, dental applications, and methods for improving their mechanical properties. Notable research is highlighted regarding (1 application of calcium phosphate into various fields in dentistry; (2 improving mechanical properties of calcium phosphate; (3 biomimetic process and functionally graded materials. This paper deals with most common types of the calcium phosphate materials such as hydroxyapatite and tricalcium phosphate which are currently used in dental and medical fields.

  1. Preparation, characterization and investigation of in vitro and in vivo biological properties of strontium-modified calcium phosphate cement for bone defect repair

    Directory of Open Access Journals (Sweden)

    Reza Masaeli

    2015-12-01

    Full Text Available Background and Aims: The aim of this study was to evaluate the invitro and invivo performance of a 3 wt% of strontium additive hydroxyapatite calcium phosphate cements (CPC. Materials and Methods: The prepared calcium phosphate cement was characterized with XRD, FTIR, setting time, STA and in vitro and in vivo biological analyses. The MTT assay ALP activities as in vitro study and radiological and histological examinations as in vivo study between the three groups of 3 wt% Sr-HA/CPC, CPC and control were performed and compared. Data were analyzed using T-test and One-way ANOVA. Results: XRD analysis demonstrated that by increasing the ratio of Powder/Liquid (P/L, the crystallinity of the prepared cement increased. The substitution of strontium instead of calcium in CPC could also alter the crystal structure, including some structural disorder. However, in the CPC with no strontium hydroxyapatite (Sr-HA, no significant increase in the crystallinity was observed. SEM observations revealed CPC with increasing P/L ratio, the formation of hydroxyapatite crystals arising from the interaction of solid and liquid phase of cement was decreased. Also, the addition of Sr within Ca site culminated in a dramatic increase in crystallinity of hydroxyapatite. In vitro biological properties ascertained that addition of 3 wt. % Sr-HA into CPC enhanced MTT assay and ALP activity, which could be due to the presence of strontium ions. The histological study showed that greater remodeling was seen at 4 weeks after implantation when the 3 wt% Sr-HA/CPC was used. Conclusion: The obtained results cleared that CPC can be a potential candidate as a carrier with strontium additives for bone remodeling and regeneration.

  2. The formation of tertiary dentin after pulp capping with a calcium phosphate cement, loaded with PLGA microparticles containing TGF-beta1.

    OpenAIRE

    W. Zhang; Walboomers, X.F.; Jansen, J. A.

    2008-01-01

    The aim of the current study was to evaluate the effect of a calcium phosphate material equipped with poly (lactic-co-glycolic acid) microspheres for pulp capping, and to measure the dentin bridge formation, when using various concentrations of transforming growth factor (TGF) beta1. Preset samples were made (2 mm diameter; 2 mm height), containing 0 (controls), 20, or 400 ng TGF-beta1. These were placed in goat incisors. Incisors capped with glass-ionomer cement only were used as negative co...

  3. Casein Aggregates Built Step-by-Step on Charged Polyelectrolyte Film Surfaces Are Calcium Phosphate-cemented*

    OpenAIRE

    Nagy, Krisztina; Pilbat, Ana-Maria; Groma, Géza; Szalontai, Balázs; Cuisinier, Frédéric J.G.

    2010-01-01

    The possible mechanism of casein aggregation and micelle buildup was studied in a new approach by letting α-casein adsorb from low concentration (0.1 mg·ml−1) solutions onto the charged surfaces of polyelectrolyte films. It was found that α-casein could adsorb onto both positively and negatively charged surfaces. However, only when its negative phosphoseryl clusters remained free, i.e. when it adsorbed onto a negative surface, could calcium phosphate (CaP) nanoclusters bind to the casein mole...

  4. Polyelectrolyte addition effect on the properties of setting hydraulic cements based on calcium phosphate; Efeito da adicao de polieletrolitos sobre as propriedades de cimentos de fosfato de calcio de pega hidraulica

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Luis A. dos; Oliveira, Luci C. de; Rigo, Eliana C.S.; Boschi, Anselmo Ortega [Sao Carlos Univ., SP (Brazil). Dept. de Engenharia de Materiais; Carrodeguas, Raul Gracia [Universidad de La Habana, Habana, (Cuba). Centro de Biomateriales

    1997-12-31

    In the present work the effects of the addition of some poly electrolytes (sodium alginate and poly acrylic acid) on the solubility, crystalline phases, pH and mechanical strength under compression of three calcium phosphate cements were studied. (author) 10 refs., 2 figs., 4 tabs.

  5. Calcium phosphate ceramics in drug delivery

    Science.gov (United States)

    Bose, Susmita; Tarafder, Solaiman; Edgington, Joe; Bandyopadhyay, Amit

    2011-04-01

    Calcium phosphate (CaP) particulates, cements and scaffolds have attracted significant interest as drug delivery vehicles. CaP systems, including both hydroxyapaptite and tricalcium phosphates, possess variable stoichiometry, functionality and dissolution properties which make them suitable for cellular delivery. Their chemical similarity to bone and thus biocompatibility, as well as variable surface charge density contribute to their controlled release properties. Among specific research areas, nanoparticle size, morphology, surface area due to porosity, and chemistry controlled release kinetics are the most active. This article discusses CaP systems in their particulate, cements, and scaffold forms for drug, protein, and growth factor delivery toward orthopedic and dental applications.

  6. Preparation of a Novel Calcium Phosphate Cement Using N-methylene Phosphonic Chitosan as a Gelling Agent

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    A modified chitosan ( N-methylene phosphonic Chitosan, NMPC ) was synthesized to improve solubility and ability to bind calcium ion. The properties of the raw material chitosan and its derivative NMPC were characterized using FTIR, 1 H-NMR. The aim of this study was to enhance the compressive CPC by reinforcing with NMPC. A formulation consisting of CPC powder, buffer solution and gelling agent was used for preparation of the CPC. CPC powder consisted of tetracalcium phosphate (TTCP) and dicalcium phosphate anhydrous ( DCPA ). NMPC which acted as the gelling agent was dissolved iuto KH2 PO4 -Na2 HPO4 buffer solution. Each specimen in the mold was sandwiched between two fritted glass sides and kept for 24 hours. Compressive strengths were determined, the setting product was identified using X-ray diffraction and scanning electron microscopy was used to investigate the hydroxyapatite particles size and porosity. The experimental results showed that the dominating influence on the compressive strengths of CPC-NMPC was the HA particle size, its uniformity and appropriate porosity.

  7. Development of highly-filled, bioactive acrylic-based composite bone cements for orthopedic and craniofacial surgery: Tuning of material properties after incorporation of calcium phosphate and antimicrobial fillers

    Science.gov (United States)

    Rodriguez, Lucas Carlos

    Bone cements are used in a variety of healthcare specialties ranging from orthopedics to dentistry to craniofacial surgery to spinal disc reconstruction. These materials need characteristics which mimic their surrounding tissues. Currently available materials have struggled to maintain these necessary characteristics. Poly (methyl methacrylate) is a very high strength bio-inert polymer which has been utilized in healthcare since the 1940's. Calcium phosphate cements are well established as being bone mimicking, but cannot sustain the compressive loads in a weight bearing application. This study sought to solve the problem of currently available bone cements by filling calcium phosphates and antimicrobials into an acrylic polymer matrix. The intended outcome was a material capable of retaining high mechanical stability from the acrylic polymer phase, while becoming sufficiently bone mimicking and antimicrobial. This thesis work presented, characterizes the material properties of the developed materials and eventually isolates a material of interest for future studies.

  8. Light weight phosphate cements

    Science.gov (United States)

    Wagh, Arun S.; Natarajan, Ramkumar,; Kahn, David

    2010-03-09

    A sealant having a specific gravity in the range of from about 0.7 to about 1.6 for heavy oil and/or coal bed methane fields is disclosed. The sealant has a binder including an oxide or hydroxide of Al or of Fe and a phosphoric acid solution. The binder may have MgO or an oxide of Fe and/or an acid phosphate. The binder is present from about 20 to about 50% by weight of the sealant with a lightweight additive present in the range of from about 1 to about 10% by weight of said sealant, a filler, and water sufficient to provide chemically bound water present in the range of from about 9 to about 36% by weight of the sealant when set. A porous ceramic is also disclosed.

  9. Regulation of physicochemical properties, osteogenesis activity, and fibroblast growth factor-2 release ability of β-tricalcium phosphate for bone cement by calcium silicate

    Energy Technology Data Exchange (ETDEWEB)

    Su, Ching-Chuan [Antai Medical Care Cooperation Antai Tian-Sheng Memorial Hospital, Pingtung, Taiwan (China); Kao, Chia-Tze; Hung, Chi-Jr [School of Dentistry, Chung Shan Medical University, Taichung, Taiwan (China); Department of Dentistry, Chung Shan Medical University Hospital, Taichung, Taiwan (China); Chen, Yi-Jyun [School of Dentistry, Chung Shan Medical University, Taichung, Taiwan (China); Department of Dentistry, Chung Shan Medical University Hospital, Taichung, Taiwan (China); Dental Department, Taichung Hospital, Ministry of Health and Welfare, Taichung City, Taiwan (China); Huang, Tsui-Hsien, E-mail: thh@csmu.edu.tw [School of Dentistry, Chung Shan Medical University, Taichung, Taiwan (China); Department of Dentistry, Chung Shan Medical University Hospital, Taichung, Taiwan (China); Shie, Ming-You, E-mail: eviltacasi@gmail.com [Institute of Oral Science, Chung Shan Medical University, Taichung, Taiwan (China)

    2014-04-01

    β-Tricalcium phosphate (β-TCP) is an osteoconductive material. For this research we have combined it with a low degradation calcium silicate (CS) to enhance its bioactive and osteostimulative properties. To check its effectiveness, a series of β-TCP/CS composites with different ratios were prepared to make new bioactive and biodegradable biocomposites for bone repair. Formation of bone-like apatite, the diametral tensile strength, and weight loss of composites were considered before and after immersion in simulated body fluid (SBF). In addition, we also examined the effects of fibroblast growth factor-2 (FGF-2) released from β-TCP/CS composites and in vitro human dental pulp cell (hDPC) and studied its behavior. The results showed that the apatite deposition ability of the β-TCP/CS composites was enhanced as the CS content was increased. For composites with more than 50% CS contents, the samples were completely covered by a dense bone-like apatite layer. At the end of the immersion point, weight losses of 19%, 24%, 33%, 42%, and 51% were observed for the composites containing 0%, 30%, 50%, 70% and 100% β-TCP cements, respectively. In vitro cell experiments show that the CS-rich composites promote human dental pulp cell (hDPC) proliferation and differentiation. However, when the CS quantity in the composite is less than 70%, the amount of cells and osteogenesis protein of hDPCs was stimulated by FGF-2 released from β-TCP/CS composites. The combination of FGF-2 in degradation of β-TCP and osteogenesis of CS gives a strong reason to believe that these calcium-based composite cements may prove to be promising bone repair materials. - Highlights: • CS improved physicochemical properties and osteogenic activity of β-TCP. • The higher the CS in the cement, the shorter the setting time and the higher the DTS. • The cell behavior was stimulated by FGF-2 released from composite containing 50% CS. • β-TCP/CS composite with FGF-2 has optimal properties for

  10. Regulation of physicochemical properties, osteogenesis activity, and fibroblast growth factor-2 release ability of β-tricalcium phosphate for bone cement by calcium silicate

    International Nuclear Information System (INIS)

    β-Tricalcium phosphate (β-TCP) is an osteoconductive material. For this research we have combined it with a low degradation calcium silicate (CS) to enhance its bioactive and osteostimulative properties. To check its effectiveness, a series of β-TCP/CS composites with different ratios were prepared to make new bioactive and biodegradable biocomposites for bone repair. Formation of bone-like apatite, the diametral tensile strength, and weight loss of composites were considered before and after immersion in simulated body fluid (SBF). In addition, we also examined the effects of fibroblast growth factor-2 (FGF-2) released from β-TCP/CS composites and in vitro human dental pulp cell (hDPC) and studied its behavior. The results showed that the apatite deposition ability of the β-TCP/CS composites was enhanced as the CS content was increased. For composites with more than 50% CS contents, the samples were completely covered by a dense bone-like apatite layer. At the end of the immersion point, weight losses of 19%, 24%, 33%, 42%, and 51% were observed for the composites containing 0%, 30%, 50%, 70% and 100% β-TCP cements, respectively. In vitro cell experiments show that the CS-rich composites promote human dental pulp cell (hDPC) proliferation and differentiation. However, when the CS quantity in the composite is less than 70%, the amount of cells and osteogenesis protein of hDPCs was stimulated by FGF-2 released from β-TCP/CS composites. The combination of FGF-2 in degradation of β-TCP and osteogenesis of CS gives a strong reason to believe that these calcium-based composite cements may prove to be promising bone repair materials. - Highlights: • CS improved physicochemical properties and osteogenic activity of β-TCP. • The higher the CS in the cement, the shorter the setting time and the higher the DTS. • The cell behavior was stimulated by FGF-2 released from composite containing 50% CS. • β-TCP/CS composite with FGF-2 has optimal properties for

  11. Could percutaneous femoral head arthroplasty using calcium phosphate cement be a novel therapeutic method for late-stage Legg-Calvé-Perthes disease?

    Directory of Open Access Journals (Sweden)

    Jun Wan

    2009-05-01

    Full Text Available "nLegg-Calvé-Perthes disease (LCPD belongs to the category of aseptic osteochondroses of childhood which is characterized by idiopathic avascular osteonecrosis of the femoral head which can cause severe deformity of hip joint such as coxa plana and ‘flattening femoral head'. As the harmonious structural relation of hip joint was broken, osteoarthritis of hip joint could be always observed in patients about 50 years old which finally needs to be treated with total hip replacement. In present most methods yield markedly to achieve good clinical results when dealing with late-stage of LCPD mainly because of inability of reconstruction of spherical shape of femoral head. So the direct urgent thing should be to find one way out to completely reconstruct the spherical shape of femoral head. By the enlightenment of percutaneous vertebroplasty (PKP and biological properties of calcium phosphate cement (CPC, we hypothesize that percutaneous femoral head arthroplasty using CPC can solve the problem of reconstruction of spherical framework of femoral head in late-stage LCPD and pave a brand-new way to achieve excellent clinical results in patients of late-stage LCPD.  

  12. Calcium Aluminate Cement Hydration Model

    Directory of Open Access Journals (Sweden)

    Matusinović, T.

    2011-01-01

    Full Text Available Calcium aluminate cement (AC is a very versatile special cement used for specific applications. As the hydration of AC is highly temperature dependent, yielding structurally different hydration products that continuously alter material properties, a good knowledge of thermal properties at early stages of hydration is essential. The kinetics of AC hydration is a complex process and the use of single mechanisms models cannot describe the rate of hydration during the whole stage.This paper examines the influence of temperature (ϑ=5–20 °C and water-to-cement mass ratio (mH /mAC = 0.4; 0.5 and 1.0 on hydration of commercial iron-rich AC ISTRA 40 (producer: Istra Cement, Pula, Croatia, which is a part of CALUCEM group, Figs 1–3. The flow rate of heat generation of cement pastes as a result of the hydration reactions was measured with differential microcalorimeter. Chemically bonded water in the hydrated cement samples was determined by thermo-gravimetry.Far less heat is liberated when cement and water come in contact for the first time, Fig. 1, than in the case for portland cement (PC. Higher water-to-cement ratio increases the heat evolved at later ages (Fig. 3 due to higher quantity of water available for hydration. A significant effect of the water-to-cement ratio on the hydration rate and hydration degree showed the importance of water as being the limiting reactant that slows down the reaction early. A simplified stoichiometric model of early age AC hydration (eq. (8 based on reaction schemes of principal minerals, nominally CA, C12A7 and C4AF (Table 1, was employed. Hydration kinetics after the induction period (ϑ < 20 °C had been successfully described (Fig. 4 and Table 2 by a proposed model (eq. (23 which simultaneously comprised three main mechanisms: nucleation and growth, interaction at phase boundary, and mass transfer. In the proposed kinetic model the nucleation and growth is proportional to the amount of reacted minerals (eq

  13. Biphasic products of dicalcium phosphate-rich cement with injectability and nondispersibility

    Energy Technology Data Exchange (ETDEWEB)

    Ko, Chia-Ling [Advanced Medical Devices and Composites Laboratory, Department of Fiber and Composite Materials, Feng Chia University, Taichung, 407, Taiwan (China); Dental Medical Devices and Materials Research Center, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Chen, Jian-Chih [Department of Orthopaedics, Kaohsiung Medical University Hospital, Kaohsiung 807, Taiwan (China); Department of Orthopaedics, College of Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Hung, Chun-Cheng; Wang, Jen-Chyan [Dental Medical Devices and Materials Research Center, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Department of Dentistry, Kaohsiung Medical University Hospital, Kaohsiung 807, Taiwan (China); Tien, Yin-Chun [Department of Orthopaedics, Kaohsiung Medical University Hospital, Kaohsiung 807, Taiwan (China); Department of Orthopaedics, College of Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Chen, Wen-Cheng, E-mail: wencchen@fcu.edu.tw [Advanced Medical Devices and Composites Laboratory, Department of Fiber and Composite Materials, Feng Chia University, Taichung, 407, Taiwan (China)

    2014-06-01

    In this study, a calcium phosphate cement was developed using tetracalcium phosphate and surface-modified dicalcium phosphate anhydrous (DCPA). This developed injectable bone graft substitute can be molded to the shape of the bone cavity and set in situ through the piping system that has an adequate mechanical strength, non-dispersibility, and biocompatibility. The materials were based on the modified DCPA compositions of calcium phosphate cement (CPC), where the phase ratio of the surface-modified DCPA is higher than that of the conventional CPC for forming dicalcium phosphate (DCP)-rich cement. The composition and morphology of several calcium phosphate cement specimens during setting were analyzed via X-ray diffractometry and transmission electron microscopy coupled with an energy dispersive spectroscopy system. The compressive strength of DCP-rich CPCs was greater than 30 MPa after 24 h of immersion in vitro. The reaction of the CPCs produced steady final biphasic products of DCPs with apatite. The composites of calcium phosphate cements derived from tetracalcium phosphate mixed with surface-modified DCPA exhibited excellent mechanical properties, injectability, and interlocking forces between particles, and they also featured nondispersive behavior when immersed in a physiological solution. - Highlights: • Bone cement precursor with nanocrystals is characterized. • DCP-rich CPCs with nanocrystals exhibited biphasic product phases. • Nanocrystals in cement significantly affected the interlocking ability. • Nanocrystals in cement exhibited higher strength and anti-dispersion. • DCP-rich CPCs increase the potential of bioresorption after reaction.

  14. Biphasic products of dicalcium phosphate-rich cement with injectability and nondispersibility

    International Nuclear Information System (INIS)

    In this study, a calcium phosphate cement was developed using tetracalcium phosphate and surface-modified dicalcium phosphate anhydrous (DCPA). This developed injectable bone graft substitute can be molded to the shape of the bone cavity and set in situ through the piping system that has an adequate mechanical strength, non-dispersibility, and biocompatibility. The materials were based on the modified DCPA compositions of calcium phosphate cement (CPC), where the phase ratio of the surface-modified DCPA is higher than that of the conventional CPC for forming dicalcium phosphate (DCP)-rich cement. The composition and morphology of several calcium phosphate cement specimens during setting were analyzed via X-ray diffractometry and transmission electron microscopy coupled with an energy dispersive spectroscopy system. The compressive strength of DCP-rich CPCs was greater than 30 MPa after 24 h of immersion in vitro. The reaction of the CPCs produced steady final biphasic products of DCPs with apatite. The composites of calcium phosphate cements derived from tetracalcium phosphate mixed with surface-modified DCPA exhibited excellent mechanical properties, injectability, and interlocking forces between particles, and they also featured nondispersive behavior when immersed in a physiological solution. - Highlights: • Bone cement precursor with nanocrystals is characterized. • DCP-rich CPCs with nanocrystals exhibited biphasic product phases. • Nanocrystals in cement significantly affected the interlocking ability. • Nanocrystals in cement exhibited higher strength and anti-dispersion. • DCP-rich CPCs increase the potential of bioresorption after reaction

  15. Enhanced dentin-like mineralized tissue formation by AdShh-transfected human dental pulp cells and porous calcium phosphate cement.

    Directory of Open Access Journals (Sweden)

    Lunguo Xia

    Full Text Available The aim of the present study was to investigate the effect of Sonic hedgehog (Shh on human dental pulp cells (hDPCs and the potential of complexes with Shh gene modified hDPCs and porous calcium phosphate cement (CPC for mineralized tissue formation. hDPCs were cultured and transfected with adenoviral mediated human Shh gene (AdShh. Overexpression of Shh and cell proliferation was tested by real-time PCR analysis, western blotting analysis, and MTT analysis, respectively. The odontoblastic differentiation was assessed by alkaline phosphatase (ALP activity and real-time PCR analysis on markers of Patched-1 (Ptc-1, Smoothened (Smo, Gli 1, Gli 2, Gli 3, osteocalcin (OCN, dentin matrix protein-1 (DMP-1, and dentin sialophosphoprotein (DSPP. Finally, AdShh-transfected hDPCs were combined with porous CPC and placed subcutaneously in nude mice for 8 and 12 weeks, while AdEGFP-transfected and untransfected hDPCs were treated as control groups. Results indicated that Shh could promote proliferation and odontoblastic differentiation of hDPCs, while Shh/Gli 1 signaling pathway played a key role in this process. Importantly, more mineralized tissue formation was observed in combination with AdShh transfected hDPCs and porous CPC, moreover, the mineralized tissue exhibited dentin-like features such as structures similar to dentin-pulp complex and the positive staining for DSPP protein similar to the tooth tissue. These results suggested that the constructs with AdShh-transfected hDPCs and porous CPC might be a better alternative for dental tissue regeneration.

  16. Influence of Dopamine on Physicochemical Properties of Calcium Phosphate Cement%多巴胺对磷酸钙骨水泥性能影响的研究

    Institute of Scientific and Technical Information of China (English)

    刘宗光; 屈树新; 赵军胜; 刘宇; 翁杰

    2013-01-01

    The aim of this study is to investigate effects of dopamine (DA) on physiochemical properties of calcium phosphate cement (CPC) and in vitro degradation of DA from CPC. DA was dissolved in Tris (Hydroxymethyl) aminomethane-hydrochloric acid buffer solution and mixed the solution with CPC powders after oxidized for 2 d in air. Orthogonal test was used to optimize the preparation of CPC with respect to the DA concentration, ratio of liquid to solid and pH values. Compressive tests, Gilmore needle tests, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) were used to characterize the physiochemical properties of CPC. Scanning electron microscope (SEM) and UV-Vis spectrophotometry were used to observe the micro-morphology of CPC and ire vitro degradation of DA from CPC, respectively. Compressive test and orthogonal analysis indicated that the optimal combination CPC was DA concentration 40 rng·mL-1, ratio of liquid to solid 0.3 mL·g-1 and pH value 8.5, which had the highest compressive strength with significant difference (p<0.01) compared with that of CPC-Blank. Setting time of the optimal combination CPC decreased slight but no significant difference compared to that of CPC-Blank, which could satisfied with the clinical demands. XRD and FTIR demonstrated that the addition of DA promoted the conversion of dicalcium phosphate dehydrate (DCPD).SEM found that there were more platy structure, lots of nubbly crystals and less porosity in optimal combination CPC compared with CPC-Blank. Cumulative release of DA from CPC was 29.7% and the pH values of immersion solution were safe for human body during in vitro degradation.%本论文研究含儿茶酚的多巴胺对磷酸钙骨水泥(calcium phosphate cement,CPC)的理化性能和体外降解的影响.将多巴胺溶于Tris-HCl缓冲液于空气中氧化2d,作为液相与固相粉末混合成型.选取多巴胺浓度、液固比、pH值三因素,通过正交试验选取最

  17. Calcium phosphate in catheter encrustation.

    Science.gov (United States)

    Cox, A J; Harries, J E; Hukins, D W; Kennedy, A P; Sutton, T M

    1987-02-01

    Encrusted catheters from nine female patients were the source of samples of deposits which were examined by X-ray diffraction, atomic absorption spectroscopy, infra-red spectroscopy and extended X-ray absorption fine structure (EXAFS) spectroscopy. In eight samples the only crystalline phase which could be clearly distinguished by X-ray diffraction was ammonium magnesium orthophosphate hexahydrate, NH4MgPO4 X 6H2O, which occurs naturally as the mineral struvite. However, atomic absorption spectroscopy revealed an appreciable concentration of calcium in all samples. Calcium phosphates have previously been detected in catheter deposits. Infra-red and EXAFS spectra were consistent with the calcium phosphate being present as a poorly crystalline hydroxyapatite. Thus the deposits appear to consist of a mixture of crystalline struvite and a form of hydroxyapatite which is not fully crystalline. PMID:3030487

  18. 21 CFR 582.1217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium phosphate. 582.1217 Section 582.1217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1217 Calcium phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic)....

  19. 21 CFR 182.1217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium phosphate. 182.1217 Section 182.1217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Substances § 182.1217 Calcium phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic)....

  20. 21 CFR 582.5217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium phosphate. 582.5217 Section 582.5217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5217 Calcium phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic)....

  1. Premixed calcium silicate cement for endodontic applications

    OpenAIRE

    Persson, Cecilia; Engqvist, Håkan

    2011-01-01

    Calcium silicate-based materials (also called MTA) are increasingly being used in endodontic applications. However, the handling properties of MTA are not optimal when it comes to injectability and cohesion. Premixing the cements using glycerol avoids these issues. However, there is a lack of data on the effect of common cement variables on important properties of premixed cements for endodontic applications. In this study, the effects of liquid-to-powder ratio, amount of radiopacifier and am...

  2. Effect of aluminium phosphate as admixture on oxychloride cement

    Indian Academy of Sciences (India)

    M P S Chandrawat; R N Yadav

    2000-02-01

    The effect of admixing of aluminium phosphate on oxychloride cement in the matrix has been investigated. It is shown that aluminium phosphate retards the setting process of the cement and improves water-tightness.

  3. Biphasic calcium phosphate in periapical surgery

    OpenAIRE

    Suneelkumar, Chinni; Datta, Krithika; Manali R Srinivasan; Kumar, Sampath T

    2008-01-01

    Calcium phosphate ceramics like hydroxyapatite and β -tricalcium phosphate (β -TCP) possess mineral composition that closely resembles that of the bone. They can be good bone substitutes due to their excellent biocompatibility. Biphasic calcium phosphate is a bone substitute which is a mixture of hydroxyapatite and β -tricalcium phosphate in fixed ratios. Studies have demonstrated the osteoconductive potential of this composition. This paper highlights the clinical use of biphasic calcium pho...

  4. 可注射磷酸钙骨水泥的流变性能研究%Study on the Rheological Properties of Injectable Calcium Phosphate Cement

    Institute of Scientific and Technical Information of China (English)

    陈芳萍; 刘昌胜

    2012-01-01

    The influence of additives on the theological properties of injectable calcium phosphate cement (ICPC) was investigated with an advanced expansion system rheometer. During the measurement of steady rheological properties, the viscosity, shear stress, and thixotropy were detected. During dynamic oscillation testing, the viscoelastic response of the ICPC under forced oscillation and the internal structure were unvailled. The results indicated that the ICPC showed both plastic and thixotropic behavior with little effect by additives. The introduction of these water-soluble polymers improved the viscosity and thixotropy of the ICPC, which are conducive to the stability of the whole system. These additives improve the recoverability and stability of the ICPC network after being sheared, in which xanthan gum and chitosan were the most obvious. On this basis, the time to form a gel was assessed to be in the range of 2 563 ~ 2 600 s for xanthan gum-ICPC system. In addition, with the increasing of xanthan gum contents, the thixotropic loop area of ICPC enlarged, but the for- mation of network structure was not stable under high shear condition.%采用高级流变扩展系统研究了添加剂种类及其含量对可注射磷酸钙骨水泥(ICPC)流变特性的影响。采用稳态流动实验表征浆体的静态粘度,用触变环面积、应力降低率和屈服应力表征ICPC浆体的触变性,并进行动态频率扫描和动态时间扫描实验动态监测ICPC的粘、弹、塑性变化规律以及水化反应过程流变参数的依时性。结果表明:添加剂并不改变ICPC的粘弹性。水溶性高分子化合物的加入提高了ICPC的粘度和触变性,利于整个体系的稳定;添加剂不同程度上提高了ICPC剪切后的网络结构恢复能力和稳定性,尤其以黄原胶和几丁糖最为明显。在此基础上,评估了加入黄原胶后ICPC形成凝胶的时间,约为2563~2600s。此外,随着黄原胶含量的增加

  5. Glycochenodeoxycholic acid inhibits calcium phosphate precipitation in vitro by preventing the transformation of amorphous calcium phosphate to calcium hydroxyapatite.

    OpenAIRE

    Qiu, S M; Wen, G.; Hirakawa, N; Soloway, R D; Hong, N K; Crowther, R S

    1991-01-01

    Calcium hydroxyapatite can be a significant component of black pigment gallstones. Diverse molecules that bind calcium phosphate inhibit hydroxyapatite precipitation. Because glycine-conjugated bile acids, but not their taurine counterparts, bind calcium phosphate, we studied whether glycochenodeoxycholic acid inhibits calcium hydroxyapatite formation. Glycochenodeoxycholic acid (2 mM) totally inhibited transformation of amorphous calcium phosphate microprecipitates to macroscopic crystalline...

  6. 21 CFR 182.8217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium phosphate. 182.8217 Section 182.8217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic). (b) Conditions of use. This...

  7. Reaction kinetics of dual setting α-tricalcium phosphate cements.

    Science.gov (United States)

    Hurle, Katrin; Christel, Theresa; Gbureck, Uwe; Moseke, Claus; Neubauer, Juergen; Goetz-Neunhoeffer, Friedlinde

    2016-01-01

    Addition of ductile polymers to calcium-deficient hydroxyapatite (CDHA)-forming bone cements based on α-tricalcium phosphate (α-TCP) is a promising approach to improve the mechanical performance of α-TCP cements and extend their application to load-bearing defects, which is else impeded by the brittleness of the hardened cement. One suitable polymer is poly-(2-hydroxyethylmethacrylate) (p-HEMA), which forms during cement setting by radical polymerisation of the monomer. In this study the hydration kinetics and the mechanical performance of α-TCP cements modified with addition of different HEMA concentrations (0-50 wt% in the cement liquid) was investigated by quantitative in situ XRD and four-point bending tests. Morphology of CDHA crystals was monitored by scanning electron microscopy. The hydration of α-TCP to CDHA was increasingly impeded and the visible crystal size of CDHA increasingly reduced with increasing HEMA concentration. Modification of the cements by adding 50 wt% HEMA to the cement liquid changed the brittle performance of the hardened cement to a pseudoplastic behaviour, reduced the flexural modulus and increased the work of fracture, while lower HEMA concentrations had no significant effect on these parameters. In such a composite, the extent of CDHA formation was considerably reduced (34.0 ± 1.8 wt% CDHA with 50 % HEMA compared to 54.1 ± 2.4 wt% CDHA in the reference formed after 48 h), while the general reaction kinetics were not changed. In conclusion, while the extent of CDHA formation was decreased, the mechanical properties were noticeably improved by addition of HEMA. Hence, α-TCP/HEMA composites might be suitable for application in some load-bearing defects and have adequate properties for mechanical treatment after implantation, like insertion of screws. PMID:26610924

  8. Sealing ability of mineral trioxide aggregate, calcium phosphate and polymethylmethacrylate bone cements on root ends prepared using an Erbium: Yttriumaluminium garnet laser and ultrasonics evaluated by confocal laser scanning microscopy

    Directory of Open Access Journals (Sweden)

    C Sabari Girish

    2013-01-01

    Full Text Available Background: Surgical endodontic therapy comprises of exposure of the involved root apex, resection of the apical end of the root, preparation of a class I cavity, and insertion of a root end filling material. Mineral trioxide aggregate (MTA is now the gold standard among all root end filling materials. MTA is however difficult to handle, expensive and has a very slow setting reaction. Aim: (1 To compare the sealing ability of MTA, polymethylmethacrylate (PMMA bone cement and CHITRA Calcium phosphate cement (CPC when used as root end filling material using Rhodamine B dye evaluated under a confocal laser scanning microscope. (2 To compare the seal of root ends prepared using an ultrasonic retroprep tip and an Er: YAG laser using three different root end filling materials. Statistical Analysis: Statistical analysis was performed using a one-way ANOVA and a two-way ANOVA, independent samples t-test and Scheffe′s post hoc test using SPSS Version 16 for Windows. Results: All the three materials, namely MTA, PMMA BONE CEMENT and CHITRA CPC, showed microleakage. Comparison of microleakage showed maximum peak value of 0.86 mm for MTA, 0.24 mm for PMMA bone cement and 1.37 mm for CHITRA CPC. The amount of dye penetration was found to be lesser in root ends prepared using Er: YAG laser when compared with ultrasonics, but the difference was found to be not statistically significant. Conclusion: PMMA bone cement is a better material as root end filling material to prevent apical microleakage. MTA still continues to be a gold standard root end filling material showing minimum microleakage. Er: YAG laser is a better alternative to ultrasonics for root end preparations.

  9. Fabrication of Phosphate Cement with High Integrity

    International Nuclear Information System (INIS)

    As the development of industrial society has accelerated, hazardous wastes are generated as well. According to the 1986 statistics of U.S.A, each person made 40 tons of waste in America that year. Treatment of radioactive waste is one of the most important and serious problems related to waste treatments, because its radioactivity and decaying heat have harmful effects to human and environment for a long time. Nuclear developed countries have used conventional method of treatment such as vitrification or cementation in order to stabilize and solidify radioactive waste. Although the former guarantees the formation of high leaching resistant and durable waste form, it requires several hundred (or even more than one thousand) temperature to melt glass frit. This process generates secondary waste volatilized, as well as being non-economical. Cement technology played a role of immobilizing low and middle class wastes. It has advantages of low temperature setting, low cost, easy process, etc. The alkalinity of ordinary cement, however, constrains the utility of cement to the solidification of alkaline waste. In addition, leachability and mechanical strength of cements are not quite appropriate for the stabilization of high level waste. In this regard, chemically bonded phosphate cement(CBPC), which sets by an acid-base reaction, is a potentially expectable material for immobilization of radioactive waste. CBPC not only sets at room temperature, but also encapsulates various isotopes chemically. The performance of CBPC can be enhanced by the addition of fly ash, sand, wollastonite, etc. This study aims at fabricating the CBPC containing fly ash with high integrity. Morphology, microstructure, and compressive strength are evaluated using SEM, and digital compressing machine

  10. Fabrication of Phosphate Cement with High Integrity

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Jae Hwan; Lee, Chang Hwa; Heo, Cheol Min; Jeon, Min Ku; Kang, Kweon Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2011-05-15

    As the development of industrial society has accelerated, hazardous wastes are generated as well. According to the 1986 statistics of U.S.A, each person made 40 tons of waste in America that year. Treatment of radioactive waste is one of the most important and serious problems related to waste treatments, because its radioactivity and decaying heat have harmful effects to human and environment for a long time. Nuclear developed countries have used conventional method of treatment such as vitrification or cementation in order to stabilize and solidify radioactive waste. Although the former guarantees the formation of high leaching resistant and durable waste form, it requires several hundred (or even more than one thousand) temperature to melt glass frit. This process generates secondary waste volatilized, as well as being non-economical. Cement technology played a role of immobilizing low and middle class wastes. It has advantages of low temperature setting, low cost, easy process, etc. The alkalinity of ordinary cement, however, constrains the utility of cement to the solidification of alkaline waste. In addition, leachability and mechanical strength of cements are not quite appropriate for the stabilization of high level waste. In this regard, chemically bonded phosphate cement(CBPC), which sets by an acid-base reaction, is a potentially expectable material for immobilization of radioactive waste. CBPC not only sets at room temperature, but also encapsulates various isotopes chemically. The performance of CBPC can be enhanced by the addition of fly ash, sand, wollastonite, etc. This study aims at fabricating the CBPC containing fly ash with high integrity. Morphology, microstructure, and compressive strength are evaluated using SEM, and digital compressing machine

  11. Substitution of calcium by strontium within selected calcium phosphates

    Science.gov (United States)

    Rokita, E.; Hermes, C.; Nolting, H.-F.; Ryczek, J.

    1993-06-01

    Sr incorporation in the molecules of amorphous calcium phosphate, apatitic tricalcium phosphate, hydroxyapatite, octacalcium phosphate and dicalcium phosphate dihydrate was investigated. The concentration of Sr ranged from 225 to 1010 μ g / g, i.e. it overlapped with the physiological range of Sr concentrations in human bone. The leading experimental technique was extended X-ray absorption fine structure (EXAFS) at the Sr K edge. Results of these studies demonstrated the following: (1) Sr incorporation in the calcium phosphates is compound-dependent, (2) the coordination of incorporated Sr atoms in the Ca-P molecules is similar to that of Ca atoms, but interatomic distances are ≈0.015 nm larger, (3) in apatitic tricalcium phosphate, hydroxyapatite and octacalcium phosphate lattices Sr atoms may occupy selected Ca sites, which was not the case for dicalcium phosphate dihydrate, (4) in the apatite lattice Sr atoms are coordinated by 6 PO 4 tetrahedrals and (5) EXAFS spectra at the K edge of the incorporated Sr may be used to distinguish the structures of amorphous calcium phosphate, dicalcium phosphate dihydrate as well as apatite and its derivatives (apatitic tricalcium phosphate, octacalcium phosphate).

  12. Calcium phosphate bone cement containing ABK and PLLA. Sustained release of ABK, the BMD of the femur in rats, and histological examination

    Energy Technology Data Exchange (ETDEWEB)

    Kusaka, T.; Tanaka, A.; Sasaki, S.; Takano, I.; Tahara, Y.; Ishii, Y. [Kyorin Univ., Tokyo (Japan). Dept. of Orhtopaedic Surgery

    2001-07-01

    Bone cement was prepared by mixing CPC95 (Mitsubishi Material Co., Ltd.), ABK, and PLLA at a ratio of 14 : 1 : 2. In vitro, Antibiotic sustained release tests were performed by the total amount exchange method. In animal experiments, the bone cement was infused into the right femur of 18-month-old female SD rats. After 1, 2, 4, or 6 months, the BMD was determined by DXA in the bilateral femoral bones. In addition, hard tissue specimens were prepared, and the state of bone formation was observed. The release of the antibiotic was 1.73 {mu}g/ml until 18 days after administration, maintaining a concentration over the MIC80 for MRSA. In the animal experiments, the BMD significantly increased after 2 - 4 months. In the hard tissue specimens, direct binding on the bone-cement interface and bone formation in the cement were observed after 1 month. (orig.)

  13. Vibrational investigation of calcium-silicate cements for endodontics in simulated body fluids

    Science.gov (United States)

    Taddei, Paola; Modena, Enrico; Tinti, Anna; Siboni, Francesco; Prati, Carlo; Gandolfi, Maria Giovanna

    2011-05-01

    Calcium-silicate MTA (Mineral Trioxide Aggregate) cements have been recently developed for oral and endodontic surgery. This study was aimed at investigating commercial (White ProRoot MTA, White and Grey MTA-Angelus) and experimental (wTC-Bi) accelerated calcium-silicate cements with regards to composition, hydration products and bioactivity upon incubation for 1-28 days at 37 °C, in Dulbecco's Phosphate Buffered Saline (DPBS). Deposits on the surface of the cements and the composition changes during incubation were investigated by micro-Raman and ATR/FT-IR spectroscopy, and pH measurements. Vibrational techniques disclosed significant differences in composition among the unhydrated cements, which significantly affected the bioactivity as well as pH, and hydration products of the cements. After one day in DPBS, all the cements were covered by a more or less homogeneous layer of B-type carbonated apatite. The experimental cement maintained a high bioactivity, only slightly lower than the other cements and appears a valid alternative to commercial cements, in view of its adequate setting time properties. The bioactivity represents an essential property to favour bone healing and makes the calcium-silicate cements the gold standard materials for root-apical endodontic surgery.

  14. A safer disposal of hazardous phosphate coating sludge by formation of an amorphous calcium phosphate matrix.

    Science.gov (United States)

    Navarro-Blasco, I; Duran, A; Pérez-Nicolás, M; Fernández, J M; Sirera, R; Alvarez, J I

    2015-08-15

    Phosphate coating hazardous wastes originated from the automotive industry were efficiently encapsulated by an acid-base reaction between phosphates present in the sludge and calcium aluminate cement, yielding very inert and stable monolithic blocks of amorphous calcium phosphate (ACP). Two different compositions of industrial sludge were characterized and loaded in ratios ranging from 10 to 50 wt.%. Setting times and compressive strengths were recorded to establish the feasibility of this method to achieve a good handling and a safe landfilling of these samples. Short solidification periods were found and leaching tests showed an excellent retention for toxic metals (Zn, Ni, Cu, Cr and Mn) and for organic matter. Retentions over 99.9% for Zn and Mn were observed even for loadings as high as 50 wt.% of the wastes. The formation of ACP phase of low porosity and high stability accounted for the effective immobilization of the hazardous components of the wastes. PMID:26024992

  15. Study on silicate-calcium phosphate composite bone cement modified by sodium carbonate solution%碳酸钠液相改性硅-磷酸钙复合骨水泥研究

    Institute of Scientific and Technical Information of China (English)

    李青林; 杨帮成

    2014-01-01

    以质量分数70%的硅酸三钙(Ca3 SiO5,C3 S)和30%磷酸氢钙(CaHPO4·2H2 O,DCPD)复合得到的 DCP30粉体材料为固相,以不同浓度碳酸钠溶液为液相,得到碳酸钠改性骨水泥材料。使用 X 射线衍射(XRD)、扫描电镜(SEM)、万能材料试验机等手段对不同浓度改性材料进行表征。结果显示:添加碳酸钠液相,骨水泥初、终凝时间分别缩短至16和55 min;调控碳酸钠液相浓度,可以实现短期抗压强度优化;使用碳酸钠后,固化自发生成羟基磷灰石(HA)。浸泡模拟体液(SBF)7天,材料表面覆盖 HA 沉积层,生物活性优越。碳酸钠液相改性硅-磷酸钙复合骨水泥体系的水化性能、短期力学性能以及生物活性均优于Ca3 SiO5水泥和未改性硅-磷酸钙复合骨水泥,是一种良好的生物活性骨修复材料。%Sodium carbonate solution modified bone cement materials have been prepared using sodium carbonate solution with dif-ferent concentration as liquid phase and DCP30 powder material obtained by 70% mass fraction tricalcium silicate (Ca3 SiO5 ,C3 S) and 30% dicalcium phosphate (CaHPO4 ·2H2 O,DCPD)as the solid phase.The materials were characterized by the means of X-ray diffraction (XRD),scanning electron microscope (SEM)and mechanical test.The results show that the initial and final set-ting time of bone cement is reduced to 16 and 55 min by the addition of sodium carbonate solution.The short-term mechanical strength can be optimized by controlling the concentration of sodium carbonate solution.Hydroxyapatite (HA)can spontaneously form after the use of sodium carbonate solution.HA forms on the surface of bone-cement after immersion in SBF for 7 days,indi-cating its good bioactivity.The modified system shows better hydraulic property,bioactivity and mechanical strength than Ca3 SiO5 cement and unmodifiled silicate-calcium phosphate composite bone cement,suggesting the new system is a

  16. Raloxifene combined with calcium phosphate cement for repair of rabbit mandibular defects%磷酸钙人工骨联合雷洛昔芬修复兔下颌骨缺损

    Institute of Scientific and Technical Information of China (English)

    关键; 徐峰

    2014-01-01

    背景:雷洛昔芬是第3代选择性雌激素受体调节剂,可减少骨量的丢失,增加骨组织中的矿物质含量,降低骨折风险。目的:观察雷洛昔芬结合自固化磷酸钙人工骨修复兔下颌骨缺损的效果。方法:在36只新西兰大白兔左侧下颌骨制作8 mm×4 mm×3 mm的缺损模型,随机分组,实验组12只植入自固化磷酸钙人工骨,并给予雷洛昔芬7.5 mg/(kg•d);药物组12只给予雷洛昔芬7.5 mg/(kg•d);人工骨组12只植入自固化磷酸钙人工骨。分别于治疗4,8,12周取下颌骨标本,免疫组织化学法观察骨形态发生蛋白2的表达,激光共聚焦显微镜观察转化生长因子β的表达。结果与结论:实验组治疗后4,8周时的骨形态发生蛋白2免疫组织化学染色阳性细胞数明显高于药物组与人工骨组,治疗后12周时实验组骨改建基本完成,骨形态发生蛋白2免疫组织化学染色阳性细胞数目低于其他两组。实验组转化生长因子β免疫荧光染色表达为逐步升高,到第8周时达到峰值,而药物组和人工骨组的转化生长因子β免疫荧光表达从4-12周一直呈上升状态,趋近于最高峰。说明雷洛昔芬能够促进自固化磷酸钙人工骨在骨缺损过程中骨形态发生蛋白的早期表达及早期骨痂的形成,加快骨缺损修复。%BACKGROUND:Raloxifene is the third generation of selective estrogen receptor modulators, which can decrease bone loss, increase bone mineral content, and reduce fracture risk. OBJECTIVE: To study the effects of raloxifene combined with self-setting calcium phosphate cement on the repair of rabbit mandibular defects. METHODS:Totaly 36 New Zealand white rabbits were selected to prepare 8 mm×4 mm×3 mm mandibular defect models, and then randomized equaly into experimental group (raloxifene, 7.5 mg/kg per day, combined with self-setting calcium phosphate cement), drug group (raloxifene, 7.5 mg/kg per

  17. Nanostructure of Calcium Silicate Hydrates in Cements

    KAUST Repository

    Skinner, L. B.

    2010-05-11

    Calcium silicate hydrate (CSH) is the major volume phase in the matrix of Portland cement concrete. Total x-ray scattering measurements with synchrotron x rays on synthetic CSH(I) shows nanocrystalline ordering with a particle diameter of 3.5(5) nm, similar to a size-broadened 1.1 nm tobermorite crystal structure. The CSH component in hydrated tricalcium silicate is found to be similar to CSH(I). Only a slight bend and additional disorder within the CaO sheets is required to explain its nanocrystalline structure. © 2010 The American Physical Society.

  18. Microwave assisted preparation of magnesium phosphate cement (MPC) for orthopedic applications: A novel solution to the exothermicity problem

    International Nuclear Information System (INIS)

    There are two interesting features of this paper. First, we report herein a novel microwave assisted technique to prepare phosphate based orthopedic cements, which do not generate any exothermicity during setting. The exothermic reactions during the setting of phosphate cements can cause tissue damage during the administration of injectable compositions and hence a solution to the problem is sought via microwave processing. This solution through microwave exposure is based on a phenomenon that microwave irradiation can remove all water molecules from the alkaline earth phosphate cement paste to temporarily stop the setting reaction while preserving the active precursor phase in the formulation. The setting reaction can be initiated a second time by adding aqueous medium, but without any exothermicity. Second, a special emphasis is placed on using this technique to synthesize magnesium phosphate cements for orthopedic applications with their enhanced mechanical properties and possible uses as drug and protein delivery vehicles. The as-synthesized cements were evaluated for the occurrences of exothermic reactions, setting times, presence of Mg-phosphate phases, compressive strength levels, microstructural features before and after soaking in (simulated body fluid) SBF, and in vitro cytocompatibility responses. The major results show that exposure to microwaves solves the exothermicity problem, while simultaneously improving the mechanical performance of hardened cements and reducing the setting times. As expected, the cements are also found to be cytocompatible. Finally, it is observed that this process can be applied to calcium phosphate cements system (CPCs) as well. Based on the results, this microwave exposure provides a novel technique for the processing of injectable phosphate bone cement compositions. - Highlights: • A microwave assisted system for bone cement manufacturing • A solution to exothermicity problem of acid–base reaction based bone cement

  19. The comparison between sulfate salt weathering of portland cement paste and calcium sulfoaluminate cement paste

    OpenAIRE

    Liu, Zanqun; Deng, Dehua; De Schutter, Geert

    2015-01-01

    In this paper, the damage performances of sulfate salt weathering of Portland cement paste and calcium sulfoaluminate (CSA) cement paste were compared according to authors' previous studies. It was found that the evaporation zone of speciments partially immersed in 10% Na2SO4 solution were both severely deteriorated for Portland cement and CSA cement. However, the differences were more significant: (1) the CSA cement paste were damaged just after 7 days exposure compared to the 5 months expos...

  20. Kinetics of strontium sorption in calcium phosphate

    International Nuclear Information System (INIS)

    Kinetics of strontium sorption by highly dispersed solids: tricalcium phosphate (Ca3(PO4)2, TCP) and hydroxyapatite (Ca5(PO4)3)H, HAP) were investigated. Analysis of sorption data was made taking into consideration composition and morphology of ultra micro particles. Conclusion is that the isomorphous strontium impurity is structurally sensitive element for calcium phosphate. It was determined that the beginning of strontium desorption corresponds to the beginning of transformation of the TCP - HAP (author)

  1. Synthesis and characterization of porous calcium phosphate

    International Nuclear Information System (INIS)

    The porous calcium phosphate was prepared by the continuous precipitation method using Ca(NO3)2.4H2O and NH4H2PO4 salts. The synthesized material was structurally and superficially characterized using the XRD, BET, IR TGA and SEM techniques. The obtained inorganic material was identified as calcium phosphate that presents a great specific area for what can be efficiently used as adsorbent material for adsorption studies in the radioactive wastes treatment present in aqueous solution. (Author)

  2. Apatite formation on bioactive calcium-silicate cements for dentistry affects surface topography and human marrow stromal cells proliferation.

    Science.gov (United States)

    Gandolfi, Maria Giovanna; Ciapetti, Gabriela; Taddei, Paola; Perut, Francesca; Tinti, Anna; Cardoso, Marcio Vivan; Van Meerbeek, Bart; Prati, Carlo

    2010-10-01

    The effect of ageing in phosphate-containing solution of bioactive calcium-silicate cements on the chemistry, morphology and topography of the surface, as well as on in vitro human marrow stromal cells viability and proliferation was investigated. A calcium-silicate cement (wTC) mainly based on dicalcium-silicate and tricalcium-silicate was prepared. Alpha-TCP was added to wTC to obtain wTC-TCP. Bismuth oxide was inserted in wTC to prepare a radiopaque cement (wTC-Bi). A commercial calcium-silicate cement (ProRoot MTA) was tested as control. Cement disks were aged in DPBS for 5 h ('fresh samples'), 14 and 28 days, and analyzed by ESEM/EDX, SEM/EDX, ATR-FTIR, micro-Raman techniques and scanning white-light interferometry. Proliferation, LDH release, ALP activity and collagen production of human marrow stromal cells (MSC) seeded for 1-28 days on the cements were evaluated. Fresh samples exposed a surface mainly composed of calcium-silicate hydrates CSH (from the hydration of belite and alite), calcium hydroxide, calcium carbonate, and ettringite. Apatite nano-spherulites rapidly precipitated on cement surfaces within 5 h. On wTC-TCP the Ca-P deposits appeared thicker than on the other cements. Aged cements showed an irregular porous calcium-phosphate (Ca-P) coating, formed by aggregated apatite spherulites with interspersed calcite crystals. All the experimental cements exerted no acute toxicity in the cell assay system and allowed cell growth. Using biochemical results, the scores were: fresh cements>aged cements for cell proliferation and ALP activity (except for wTC-Bi), whereas fresh cementscements for collagen synthesis. Summarizing (1) non-aged cements showed higher cell proliferation than aged cements, probably favoured by the presence of Si-OH gel and the early formation of apatite nano-spherulites; (2) the alpha-TCP doped cement aged for 28 days displayed the highest bioactivity and cell proliferation; (3) the deleterious effect of bismuth on cell

  3. Solid state NMR study calcium phosphate ceramics

    International Nuclear Information System (INIS)

    High-resolution 31P and 1H NMR spectra at 40 and 121 MHz 31P and 300 MHz 1H of synthetic and biological samples of calcium phosphates have been obtained by magic angle spinning (MAS) at spinning speeds up to 6.5 kHz, and high power proton decoupling. The samples include crystalline hydroxyapatite, a deficient hydroxyapatite characterized by a Ca/P atomic ratio of 1.5, a poorly crystallized hydroxyapatite, monetite, brushite, octacalcium phosphate, β-tricalcium phosphate and rabbit femoral bone. The interactions between nuclei in unlike structures and the mobility of acid protons are discussed. (author). 11 refs.; 2 figs.; 1 tab

  4. Calcium sulfoaluminate cement blended with OPC: A potential binder to encapsulate low-level radioactive slurries of complex chemistry

    International Nuclear Information System (INIS)

    Investigations were carried out in order to solidify in cement a low-level radioactive waste of complex chemistry obtained by mixing two process streams, a slurry produced by ultra-filtration and an evaporator concentrate with a salinity of 600 gxL-1. Direct cementation with Portland cement (OPC) was not possible due to a very long setting time of cement resulting from borates and phosphates contained in the waste. According to a classical approach, this difficulty could be solved by pre-treating the waste to reduce adverse cement-waste interactions. A two-stage process was defined, including precipitation of phosphates and sulfates at 60 deg. C by adding calcium and barium hydroxide to the waste stream, and encapsulation with a blend of OPC and calcium aluminate cement (CAC) to convert borates into calcium quadriboroaluminate. The material obtained with a 30% waste loading complied with specifications. However, the pre-treatment step made the process complex and costly. A new alternative was then developed: the direct encapsulation of the waste with a blend of OPC and calcium sulfoaluminate cement (CSA) at room temperature. Setting inhibition was suppressed, which probably resulted from the fact that, when hydrating, CSA cement formed significant amounts of ettringite and calcium monosulfoaluminate hydrate which incorporated borates into their structure. As a consequence, the waste loading could be increased to 56% while keeping acceptable properties at the laboratory scale.

  5. Three-dimensionally Perforated Calcium Phosphate Ceramics

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Porous calcium phosphate ceramics were produced by compression molding using a special mold followed by sintering. The porous calcium phosphate ceramics have three-dimensional and penetrated open pores380-400μm in diameter spaced at intervals of 200μm. The layers of the linear penetration pores alternately lay perpendicular to pore direction. The porosity was 59%-65% . The Ca/P molar ratios of the porous calcium phosphate ceramics range from 1.5 to 1.85. A binder containing methyl cellulose was most effective for preparing the powder compact among vinyl acetate, polyvinyl alcohol, starch, stearic acid, methyl cellulose and their mixtures. Stainless steel, polystyrene, nylon and bamboo were used as the long columnar male dies for the penetrated open pores. When polystyrene, nylon and bamboo were used as the long columnar male dies, the dies were burned out during the sintering process. Using stainless steel as the male dies with the removal of the dies before heat treatment resulted in a higher level of densification of the calcium phosphate ceramic.

  6. The stability mechanisms of an injectable calcium phosphate ceramic suspension.

    OpenAIRE

    Fatimi, Ahmed; Tassin, Jean-François; Axelos, Monique; Weiss, Pierre

    2010-01-01

    Calcium phosphate ceramics are widely used as bone substitutes in dentistry and orthopedic applications. For minimally invasive surgery an injectable calcium phosphate ceramic suspension (ICPCS) was developed. It consists in a biopolymer (hydroxypropylmethylcellulose: HPMC) as matrix and bioactive calcium phosphate ceramics (biphasic calcium phosphate: BCP) as fillers. The stability of the suspension is essential to this generation of "ready to use" injectable biomaterial. But, during storage...

  7. 21 CFR 182.6215 - Monobasic calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Monobasic calcium phosphate. 182.6215 Section 182.6215 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....6215 Monobasic calcium phosphate. (a) Product. Monobasic calcium phosphate. (b) Conditions of use....

  8. 21 CFR 582.6215 - Monobasic calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Monobasic calcium phosphate. 582.6215 Section 582.6215 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....6215 Monobasic calcium phosphate. (a) Product. Monobasic calcium phosphate. (b) Conditions of use....

  9. Apatite precipitation on a novel fast-setting calcium silicate cement containing fluoride

    Science.gov (United States)

    Ranjkesh, Bahram; Chevallier, Jacques; Salehi, Hamideh; Cuisinier, Frédéric; Isidor, Flemming; Løvschall, Henrik

    2016-01-01

    Abstract Aim: Calcium silicate cements are widely used in endodontics. Novel fast-setting calcium silicate cement with fluoride (Protooth) has been developed for potential applications in teeth crowns including cavity lining and cementation. Objective: To evaluate the surface apatite-forming ability of Protooth compositions as a function of fluoride content and immersion time in phosphate-buffered saline (PBS). Material and methods: Three cement compositions were tested: Protooth (3.5% fluoride and 10% radiocontrast), ultrafast Protooth (3.5% fluoride and 20% radiocontrast), and high fluoride Protooth (15% fluoride and 25% radiocontrast). Powders were cap-mixed with liquid, filled to the molds and immersed in PBS. Scanning electron microscopy, energy dispersive X-ray analysis, and Raman spectroscopy were used to characterize the precipitations morphology and composition after 1, 7, 28, and 56 days. Apatite/belite Raman peak height indicated the apatite thickness. Results: Spherical calcium phosphate precipitations with acicular crystallites were formed after 1-day immersion in PBS and Raman spectra disclosed the phosphate band at 965 cm−1, supporting the apatite formation over Protooth compositions. The apatite deposition continued and more voluminous precipitations were observed after 56 days over the surface of all cements. Raman bands suggested the formation of β-type carbonated apatite over Protooth compositions. High fluoride Protooth showed the most compact deposition with significantly higher apatite/belite ratio compared to Protooth and ultrafast Protooth after 28 and 56 days. Conclusions: Calcium phosphate precipitations (apatite) were formed over Protooth compositions after immersion in PBS with increasing apatite formation as a function of time. High fluoride Protooth exhibited thicker apatite deposition. PMID:27335901

  10. Phase transformations, microstructure formation and in vitro osteoblast response in calcium silicate/brushite cement composites.

    Science.gov (United States)

    Sopcak, T; Medvecky, L; Giretova, M; Kovalcikova, A; Stulajterova, R; Durisin, J

    2016-01-01

    Self-setting simple calcium silicate/brushite (B) biocements with various Ca/P ratios were prepared by mutual mixing of both monocalcium silicate hydrate (CSH) or β-wollastonite (woll) powders with B and the addition of 2 wt% NaH2PO4 solution as a hardening liquid. The phase composition of the final composites and the texture of the surface calcium phosphate/silica layer were controlled by the starting Ca/P ratio in composites and the pH during setting. It was verified that the presence of continuous bone-like calcium phosphate coating on the surface of the samples was not essential for in vitro osteoblast proliferation. The nanocrystalline calcium deficient hydroxyapatite and amorphous silica were found as the main setting products in composite mixtures with a Ca/P ratio close to the region of the formation of deficient hydroxyapatite-like calcium phosphates. No CSH phase with a lower Ca/Si ratio was identified after transformation. The results confirmed a small effect of the monocalcium silicate addition on the compressive strength (CS) of cements up to 30 wt% (around 20-25 MPa) and a significant rise of the value in 50 woll/B cement (65 MPa). The final setting times of the cement composites varied between 5 and 43 min depending on the P/L ratio and the type of monocalcium silicate phase in the cement mixture. 10CSH/B and 50 woll/B cements with different textures but free of both the needle-like and perpendicularly-oriented hydroxyapatite particles on the surface of the samples had low cytotoxicity. PMID:27509265

  11. Hydration and dimensional stability of calcium aluminate cement based systems

    OpenAIRE

    Bizzozero, Julien

    2014-01-01

    Calcium aluminate cements (CAC) are often used in combination with calcium sulfate and Portland cement for special applications where rapid setting, rapid drying and shrinkage compensation are required. A growing fraction of the clinker, which has the highest CO2 intensity, is being replaced by supplementary cementitious materials (SCM). These SCM are usually from industrial by-products such as slag, fly ashes or can simply be raw materials such as limestone. This project aims at replacing th...

  12. Influence of the calcium sulfate source on the rheological behaviour of calcium sulfoaluminate cement pastes

    OpenAIRE

    Santacruz, Isabel; García-Maté, Marta; G. Aranda, Miguel Ángel; De la Torre, Ángeles G.

    2013-01-01

    Calcium sulfoaluminate (CSA) cements are receiving increasing attention since their manufacture produces much less CO2 than ordinary Portland cement (OPC) [1]. In addition, they show interesting properties such as high early-age strengths, short setting times and impermeability. The main uses of these CSA cements are for quick repairs and pre-cast products or floor concrete applications. They are prepared by mixing the clinker with different amounts of a calcium sulfate set regulator such as ...

  13. Effect of distribution pattern of calcium polyphosphate fiber on mechanical properties of calcium phosphate cement%聚磷酸钙纤维分布形态对磷酸盐骨水泥力学性能的影响

    Institute of Scientific and Technical Information of China (English)

    史雪婷; 徐立新; 杨云龙

    2013-01-01

    制备CPP/(α-TCP/n-HAP)骨水泥复合材料,观察并分析乱向及准单向分布的CPP纤维长度和含量对骨水泥凝固时间及力学性能的影响.结果显示:长度为3 mm、质量分数为10%的CPP纤维准单向分布时骨水泥试样抗压强度和抗弯强度分别比CPP纤维乱向分布时提高18.7%和34.5%;扫描电镜显示,CPP在CPC骨水泥基体中分布均匀,结合性能好.准单向分布的CPP纤维对CPC骨水泥有更好的增强、增韧效果.%CPP/(α-TCP/n-HAP) bone cement composites were prepared and the effect of the length and content of CPP fiber distributed quasi-unidirectionally and randomly in bone cement on its hardening time and mechanical properties were observed and analysed. The result showed that compressive and bending strength of bone cement with CPP fiber distributed quasi-unidirectionally in it would be enhanced by 18. 7% and 34. 5% more than those with random distribution of the fiber when CPP fiber length was 3 mm and content was 10%. Scanning electron microscope showed that CPP fibers were distributed uniformly in CPC bone cement base and exhibited good combining performance. CPP fiber distributed quasi-unidirectionally in bone cement exhibited stronger enhanced strength and toughness than CPC bone cement.

  14. 磷酸钙骨水泥对股骨颈骨折内固定辅强作用的组织学评价%Histological evaluation of calcium phosphate cement in augmentation of femoral neck fracture fixation

    Institute of Scientific and Technical Information of China (English)

    张伟; 赵军; 胡春明; 李玉林; 森川圭造; 杉本友宏; 佐藤啓二; 丹羽滋郎; 徐莘香

    2006-01-01

    宿主骨的改变.主要观察指标:术后不同时间各组骨水泥周围新骨形成情况及宿主骨的变化.结果:实验选用45只成熟中国绵羊,全部进入结果分析.术后不同时间各组骨水泥周围新骨形成情况及宿主骨的变化:①非辅强组:术后3周在螺钉周围产生少量纤维组织,且宿主骨骨床有显微破坏,但显微破坏在术后6及12周时可见修复.②磷酸钙骨水泥辅强组:术后3,6,12周磷酸钙骨水泥充满于螺钉和宿主骨之间,而且磷酸钙骨水泥表面有新骨形成,在新骨和磷酸钙骨水泥之间没有纤维组织介入.在术后12周可见大量新骨形成,且见许多骨小管.③聚甲基丙烯酸甲酯辅强组:术后3周在骨床与聚甲基丙烯酸甲酯之间产生大量纤维组织,可见明显骨吸收,术后6及12周尤为明显.结论:由于磷酸钙骨水泥具有良好的组织相容性、骨传导性及自身改建能力,因此对股骨颈骨折提供了长期有益的辅强作用.%BACKGROUND: Structural characteristics of calcium phosphate cement (CPC) offer substantial mechanical integrity for fracture stabilization and fixation during the healing process, with particular applications in mechanically compromised osteoporotic bone.OBJECTIVE: To investigate the mechanism of the augmentation to fixation with CPC, comparing with screw fixation augmented by polymenthymethacrylate (PMMA) bone cement or with unaugmented screw fixation for femoral neck fractures in sheep by histological evaluation.DESIGN: Randomized controlled, duplicated observation and opening study.SETTING: Departments of Orthopeadics and General Surgery, the First Hospital of Jilin University; Department of Pathology, Basic Medical College of Jilin University; Department of Plastic Surgery, Aichi Medical University of Japan.MATERIALS: The experiment was completed in the Taonan Municipal Hospital of Jilin, Jilin University and Aichi Medical University of Japan from January 1999 to January 2004. A

  15. Studies on the permeability of polyacrylate and phosphate cements by means of 131I

    International Nuclear Information System (INIS)

    The permeability of a zinc phosphate cement and of a typical representative of the polyacrylate cements was studied radiometrically and autoradiographically, using 131I. The permeability of the phosphate cement was considerably greater than that of the polyacrylate cement. However, further studies evidenced that the penetrability of the polyacrylate cement increased markedly, which might be due to the contraction of the material. Compared with the findings of previous studies the permeability of a phosphate cement frequently used revealed to be equal to that of EBA cements and polyacrylate cements during the first day of setting. Thus, the EBA cements and the polyacrylate cements are not superior to zinc phosphate cements in this respect. (author)

  16. Dissolution kinetics of calcium phosphate coatings.

    Science.gov (United States)

    Burke, E M; Lucas, L C

    1998-01-01

    Plasma spray and high velocity oxy-fuel (HVOF) techniques produce coatings with varying composition and amounts of amorphous and crystalline phases. For coatings containing greater amorphous phases, a higher release of calcium ions is evident when samples are placed in Hank's calcium-free balanced salt solutions. Calcium is released from the amorphous phases in the coating, a conclusion that is supported by x-ray powder diffraction (XRD) results. Ion beam sputtering and RF magnetron sputtering under lower energy conditions produce amorphous coatings that will dissolve in a very short time period. When heat treated, crystalline phases are produced in the coatings. Heat-treated coatings are significantly more stable than the amorphous coatings. The dissolution rates of both amorphous and crystalline coatings produced by RF magnetron sputtering have been measured under constant solution conditions at pH 6.50. No reprecipitation is possible under these conditions. The amorphous coating dissolved at a significantly higher rate than the heat-treated coating. Reprecipitation of calcium phosphate onto amorphous coatings is possible in a physiological pH solution. Under these conditions, the dissolution rate of the amorphous coating is four times slower than at the pH 6.50 conditions. PMID:10196809

  17. Seed selections for crystallization of calcium phosphate for phosphorus recovery

    Institute of Scientific and Technical Information of China (English)

    SONG Yong-hui; Dietfried DONNERT; Ute BERG; Peter G. WEIDLER; Rolf NUEESCH

    2007-01-01

    Seed induces and promotes the crystallization of calcium phosphate, and acts as carrier of the recovered phosphorus (P). In order to select suitable seed for P recovery from wastewater, three seeds including Apatite (AP), Juraperle (JP) and phosphate-modified Juraperle (M-JP) were tested and compared. Batch and fixed-bed column experiments of seeded crystallization of calcium phosphate were undertaken by using synthetic wastewater with 10 mg/L P phosphate. It shows that AP has bad enduring property in the crystallization process, while JP has better performance for multiple uses, and M-JP is a hopeful seed for P recovery by crystallization of calcium phosphate.

  18. Calcium phosphate mineralization is widely applied in crustacean mandibles

    OpenAIRE

    Shmuel Bentov; Aflalo, Eliahu D.; Jenny Tynyakov; Lilah Glazer; Amir Sagi

    2016-01-01

    Crustaceans, like most mineralized invertebrates, adopted calcium carbonate mineralization for bulk skeleton reinforcement. Here, we show that a major part of the crustacean class Malacostraca (which includes lobsters, crayfishes, prawns and shrimps) shifted toward the formation of calcium phosphate as the main mineral at specified locations of the mandibular teeth. In these structures, calcium phosphate is not merely co-precipitated with the bulk calcium carbonate but rather creates speciali...

  19. Push-out bond strength of CPP-ACP-modified calcium silicate-based cements.

    Science.gov (United States)

    Dawood, Alaa E; Manton, David J; Parashos, Peter; Wong, Rebecca H k; Palamara, Joseph E A; Reynolds, Eric C

    2015-01-01

    This study evaluated the push-out bond strength of 0%, 0.5%, 1.0%, 2.0% and 3.0% (w/w) casein phosphopeptide-amorphous calcium phosphate (CPP-ACP)-modified calcium silicate-based cements (CSCs). The push-out bond strength of a trial MTA was also compared with two CSCs (Biodentine(™) and Angelus(®) MTA). Three hundred 1 mm thick horizontal root sections were prepared from 60 singlerooted human teeth. The canal space of each section was enlarged and filled with the cements. The sections were stored in a phosphate buffer solution. After incubation for 2 months, the push-out bond strength was measured and the data were analyzed using one way analysis of variance followed by Tukey's test. The addition of CPP-ACP to the test cements increased the push-out bond strength (p<0.05). The push-out bond strength of Biodentine(™) was higher than the other cements (p<0.05). There was no statistically significant difference between Angelus(®) MTA and the trial MTA with most of CPP-ACP concentrations. PMID:26235714

  20. Hydration of Portland cement with additions of calcium sulfoaluminates

    Energy Technology Data Exchange (ETDEWEB)

    Le Saout, Gwenn, E-mail: gwenn.le-saout@mines-ales.fr [Empa, Swiss Federal Laboratories for Materials Science and Technology, Concrete and Construction Chemistry Laboratory, Ueberlandstrasse 129, CH-8600 Duebendorf (Switzerland); Lothenbach, Barbara [Empa, Swiss Federal Laboratories for Materials Science and Technology, Concrete and Construction Chemistry Laboratory, Ueberlandstrasse 129, CH-8600 Duebendorf (Switzerland); Hori, Akihiro [DENKA Chemicals GmbH, Wehrhahn-Center, Cantadorstr. 3, D-40211 Duesseldorf (Germany); Higuchi, Takayuki [Denki Kagaku Kogyo Kabushiki Kaisha (DENKA), Omi, Itoigawa, Niigata, 949-0393 (Japan); Winnefeld, Frank [Empa, Swiss Federal Laboratories for Materials Science and Technology, Concrete and Construction Chemistry Laboratory, Ueberlandstrasse 129, CH-8600 Duebendorf (Switzerland)

    2013-01-15

    The effect of mineral additions based on calcium aluminates on the hydration mechanism of ordinary Portland cement (OPC) was investigated using isothermal calorimetry, thermal analysis, X-ray diffraction, scanning electron microscopy, solid state nuclear magnetic resonance and pore solution analysis. Results show that the addition of a calcium sulfoaluminate cement (CSA) to the OPC does not affect the hydration mechanism of alite but controls the aluminate dissolution. In the second blend investigated, a rapid setting cement, the amorphous calcium aluminate reacts very fast to ettringite. The release of aluminum ions strongly retards the hydration of alite but the C-S-H has a similar composition as in OPC with no additional Al to Si substitution. As in CSA-OPC, the aluminate hydration is controlled by the availability of sulfates. The coupling of thermodynamic modeling with the kinetic equations predicts the amount of hydrates and pore solution compositions as a function of time and validates the model in these systems.

  1. Hydration of Portland cement with additions of calcium sulfoaluminates

    International Nuclear Information System (INIS)

    The effect of mineral additions based on calcium aluminates on the hydration mechanism of ordinary Portland cement (OPC) was investigated using isothermal calorimetry, thermal analysis, X-ray diffraction, scanning electron microscopy, solid state nuclear magnetic resonance and pore solution analysis. Results show that the addition of a calcium sulfoaluminate cement (CSA) to the OPC does not affect the hydration mechanism of alite but controls the aluminate dissolution. In the second blend investigated, a rapid setting cement, the amorphous calcium aluminate reacts very fast to ettringite. The release of aluminum ions strongly retards the hydration of alite but the C–S–H has a similar composition as in OPC with no additional Al to Si substitution. As in CSA–OPC, the aluminate hydration is controlled by the availability of sulfates. The coupling of thermodynamic modeling with the kinetic equations predicts the amount of hydrates and pore solution compositions as a function of time and validates the model in these systems.

  2. Rheological and hydration characterization of calcium sulfoaluminate cement pastes

    OpenAIRE

    García-Maté, Marta; Santacruz, Isabel; de la Torre, Ángeles G.; León-Reina, Laura; Aranda, Miguel A. G.

    2012-01-01

    Calcium sulfoaluminate (CSA) cements are currently receiving a lot of attention because their manufacture produces less CO2 than ordinary Portland cement (OPC). However, it is essential to understand all parameters which may affect the hydration processes. This work deals with the study of the effect of several parameters, such as superplasticizer (SP), gypsum contents (10, 20 and 30 wt%) and w/c ratio (0.4 and 0.5), on the properties of CSA pastes during early hydration. This characteriza...

  3. Nano-porous calcium phosphate balls.

    Science.gov (United States)

    Kovach, Ildyko; Kosmella, Sabine; Prietzel, Claudia; Bagdahn, Christian; Koetz, Joachim

    2015-08-01

    By dropping a NaH2PO4·H2O precursor solution to a CaCl2 solution at 90°C under continuous stirring in presence of two biopolymers, i.e. gelatin (G) and chitosan (C), supramolecular calcium phosphate (CP) card house structures are formed. Light microscopic investigations in combination with scanning electron microscopy show that the GC-based flower-like structure is constructed from very thin CP platelets. Titration experiments indicate that H-bonding between both biopolymers is responsible for the synergistic effect in presence of both polymers. Gelatin-chitosan-water complexes play an important role with regard to supramolecular ordering. FTIR spectra in combination with powder X-ray diffraction show that after burning off all organic components (heating up >600°C) dicalcium and tricalcium phosphate crystallites are formed. From high resolution transmission electron microscopy (HR-TEM) it is obvious to conclude, that individual crystal platelets are dicalcium phosphates, which build up ball-like supramolecular structures. The results reveal that the GC guided crystal growth leads to nano-porous supramolecular structures, potentially attractive candidates for bone repair. PMID:26052107

  4. Theoretical and experimental approach to test the cohesion of calcium phosphate pastes

    Directory of Open Access Journals (Sweden)

    M Bohner

    2006-08-01

    Full Text Available Recent studies have revealed that the ability of a calcium phosphate cement paste to harden in a physiological environment without desintegrating into small particles might be a key property to ensure a safe and reliable clinical use of calcium phosphate cements. However, this property called cohesion is not well understood and has not been studied extensively. The goal of the present study was to better understand which factors affect the cohesion of a calcium phosphate paste using the combination of a theoretical and experimental approach. In the theoretical approach, factors expected to influence the paste cohesion such as Van der Waals forces, electrostatic and steric interactions, as well as osmotic effects were listed and discussed. In the experimental approach, a new method to measure the cohesion of a non-setting calcium phosphate paste was presented and used to assess the effects of various factors on this property. The new method allowed a continuous measurement of cohesion and gave reproducible results. The experimental results confirmed the theoretical predictions: an increase of the liquid-to-powder ratio of the paste and of the powder particle size, as well as the addition of citrate ions and in limited cases dissolved xanthan polymer chains reduced the paste cohesion.

  5. Hydration of calcium sulfoaluminate cements - Experimental findings and thermodynamic modelling

    International Nuclear Information System (INIS)

    Calcium sulfoaluminate cements (CSA) are a promising low-CO2 alternative to ordinary Portland cements and are as well of interest concerning their use as binder for waste encapsulation. In this study, the hydration of two CSA cements has been investigated experimentally and by thermodynamic modelling between 1 h and 28 days at w/c ratios of 0.72 and 0.80, respectively. The main hydration product of CSA is ettringite, which precipitates together with amorphous Al(OH)3 until the calcium sulfate is consumed after around 1-2 days of hydration. Afterwards, monosulfate is formed. In the presence of belite, straetlingite occurs as an additional hydration product. The pore solution analysis reveals that straetlingite can bind a part of the potassium ions, which are released by the clinker minerals. The microstructure of both cements is quite dense even after 16 h of hydration, with not much pore space available at a sample age of 28 days. The pore solution of both cements is dominated during the first hours of hydration by potassium, sodium, calcium, aluminium and sulfate; the pH is around 10-11. When the calcium sulfate is depleted, the sulfate concentration drops by a factor of 10. This increases pH to around 12.5-12.8. Based on the experimental data, a thermodynamic hydration model for CSA cements based on cement composition, hydration kinetics of clinker phases and calculations of thermodynamic equilibria by geochemical speciation has been established. The modelled phase development with ongoing hydration agrees well with the experimental findings.

  6. Pathogenic Mineralization of Calcium Phosphate on Human Heart Valves

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    When calcium phosphate forms in soft tissues such as blood vessels and heart valves, it causes disease. The abnormal formation of calcium phosphate is called pathogenic mineralization or pathogenic calcification. Cases of rheumatic heart disease (RHD) always occur with fibrotic and calcified tissue of heart valve. In this article, samples taken from calcified human heart valves were studied. The characterization was performed by scanning electronic micrascope, X-ray Diffraction and transmission electron microscopy with selective diffraction patterns. It is found for the first time that calcium phosphate grains existing in the calcified human heart valves contain octacalcium phosphate (OCP).

  7. Influence of ferrite phase in alite-calcium sulfoaluminate cements

    Science.gov (United States)

    Duvallet, Tristana Yvonne Francoise

    Since the energy crisis in 1970's, research on low energy cements with low CO2- emissions has been increasing. Numerous solutions have been investigated, and the goal of this original research is to create a viable hybrid cement with the components of both Ordinary Portland cement (OPC) and calcium sulfoaluminate cement (CSAC), by forming a material that contains both alite and calcium sulfoaluminate clinker phases. Furthermore, this research focuses on keeping the cost of this material reasonable by reducing aluminum requirements through its substitution with iron. The aim of this work would produce a cement that can use large amounts of red mud, which is a plentiful waste material, in place of bauxite known as an expensive raw material. Modified Bogue equations were established and tested to formulate this novel cement with different amounts of ferrite, from 5% to 45% by weight. This was followed by the production of cement from reagent chemicals, and from industrial by-products as feedstocks (fly ash, red mud and slag). Hydration processes, as well as the mechanical properties, of these clinker compositions were studied, along with the addition of gypsum and the impact of a ferric iron complexing additive triisopropanolamine (TIPA). To summarize this research, the influence of the addition of 5-45% by weight of ferrite phase, was examined with the goal of introducing as much red mud as possible in the process without negatively attenuate the cement properties. Based on this PhD dissertation, the production of high-iron alite-calcium sulfoaluminateferrite cements was proven possible from the two sources of raw materials. The hydration processes and the mechanical properties seemed negatively affected by the addition of ferrite, as this phase was not hydrated entirely, even after 6 months of curing. The usage of TIPA counteracted this decline in strength by improving the ferrite hydration and increasing the optimum amount of gypsum required in each composition

  8. Preparation and Characterization of Porous Calcium Phosphate Bioceramics

    Institute of Scientific and Technical Information of China (English)

    Honglian Dai; Xinyu Wang; Yinchao Han; Xin Jiang; Shipu Li

    2011-01-01

    β-tricalcium phosphate (β-TCP) powder and Na2O-CaO-MgO-P2O5 glass binder were synthesized and mixed, and then the biodegradable porous calcium phosphate ceramics were successfully prepared by foaming and sintering at 850℃. The as-prepared ceramics possess a high porosity with partial three-dimension interconnected macro- and micro-pores. As in vitro experiment testified, the calcium phosphate ceramics (CPCs) has good degradability.

  9. 磷酸钙骨水泥对颈椎前路螺钉置入体强化作用的生物力学分析%Biomechanical analysis of calcium phosphate cement in augmentation of anterior cervical screw

    Institute of Scientific and Technical Information of China (English)

    陈跃平; 朱勇; 张超

    2008-01-01

    BACKGROUND: Calcium phosphate cement (CPC) can strengthen the immediate and early fixation of screws by improving the quality of bone and the surface of screws. OBJECTIVE: To evaluate the biomechanical efficacy of CPC in augmentation of anterior cervical unicortical screw fixation. DESIGN: A study of controlled observation. SETTING: Department of Orthopaedics of First Xiangya Hospital of Xiangya Medical College of Central South University. MATERIALS: Experiments were performed at the Room of Electromechanical Tensile Property of College of Material Science and Engineering of Central South University from September 2003 to January 2004. Anterior cervical unicortical screw (pure titanium) was produced by Zhangjiagang Xinda Medical Equipment Co., Ltd. Injectable calcium phosphate cement was produced by Shanghai Ruibang Biomaterial Co., Ltd. Axial pull-out sleeve was produced by Machine Manufacture Center of Central South University. METHODS: ①Sixteen cervical vertebrae (C3-6) of four fresh young man cadavers with fine results in bone mineral density (BMD) test and sixteen cervical vertebrae (C3-6) of 4 fresh old man cadavers with poor results in BMD test were selected. Specimens were provided by Department of Anatomy of Xiangya Medical College of Central South University. Mortal remains of the deceased were donated according to the will of the dead. Informed consents were obtained from their family members. Twelve vertebrae were selected in each group for three tests. Six vertebrae were selected in pull-out test, and six vertebrae in cyclic bending test and shearing test. Screw holes, which were 8 mm apart from the midline and 5°inclined centrally, were made on both sides in the front part of the vertebra. Cortical bone was not penetrated. ②A screw was randomly inserted into one side hole, which was considered to be a control group. Pull-out test was performed on material testing machine at 5 mm/min. The screw hole was filled with CPC (0.10-0.15 mL) to repair the

  10. Biomechanics study of interal fixation with hollow compression screw and composite calcium phosphate cement of osteoporotic femoral neck%复合磷酸钙骨水泥强化骨质疏松股骨颈加压空心螺钉的生物力学研究

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Objective To evaluate the biomechanics of hollow compression screw in the osteoporotic femoral neck with composite calcium phosphate cement (CCPC).Methods Sixteen femurs of superior segment were randomly divided into two groups: augmentation group and non augmentation group.CCPC was used in augmentation group.Result Augmentation with CCPC would improve the initial mobile force of hollow compression screw,the initial mobile force and the maximal axial pull out strength for augmentation group,non augmentation group increased from (192.7± 14.0)N and (202.8± 14.0)N to(328.5± 34.7)N and( 347.8± 31.2)N.There was significant difference of two groups(P< 0.01).Conclusion CCPC can enhance hollow compression screw fixation in osteoporotic femoral neck.

  11. Enhanced bioactivity of glass ionomer cement by incorporating calcium silicates.

    Science.gov (United States)

    Chen, Song; Cai, Yixiao; Engqvist, Håkan; Xia, Wei

    2016-01-01

    Glass ionomer cements (GIC) are known as a non-bioactive dental cement. During setting the GIC have an acidic pH, driven by the acrylic acid component. It is a challenge to make GIC alkaline without disturbing its mechanical properties. One strategy was to add slowly reacting systems with an alkaline pH. The aim of the present study is to investigate the possibility of forming a bioactive dental material based on the combination of glass ionomer cement and calcium silicates. Two types of GIC were used as control. Wollastonite (CS also denoted β-CaSiO3) or Mineral Trioxide Aggregate (MTA) was incorporated into the 2 types of GIC. The material formulations' setting time, compressive strength, pH and bioactivity were compared between modified GIC and GIC control. Apatite crystals were found on the surfaces of the modified cements but not on the control GIC. The compressive strength of the cement remained with the addition of 20% calcium silicate or 20% MTA after one day immersion. In addition, the compressive strength of GIC modified with 20% MTA had been increased during the 14 d immersion (p < 0 .05). PMID:26787304

  12. Furcal perforation repair using calcium enriched mixture cement

    Directory of Open Access Journals (Sweden)

    Asgary Saeed

    2010-01-01

    Full Text Available This case describes a furcal perforation in a mandibular first molar accompanied by furcal lesion which has been managed after one month. Root canal treatment was performed; subsequently, the defect was repaired with calcium enriched mixture (CEM cement. The endodontically treated tooth was restored with amalgam. A 24-month recall showed no evidence of periodontal breakdown, no symptoms, in addition to completes healing of furcal lesion. According to physical and biological properties of the newly introduced CEM cement, this novel material may be suitable for sealing and repairing the perforations. The present case report supports this hypothesis.

  13. Accelerated carbonation of Friedel's salt in calcium aluminate cement paste

    International Nuclear Information System (INIS)

    The stability of Friedel's salt with respect to carbonation has been studied in calcium aluminate cement (CAC) pastes containing NaCl (3% of Cl- by weight of cement). Carbonation was carried out on a powdered sample in flowing 5% CO2 gas at 65% relative humidity to accelerate the process. At an intermediate carbonation step, a part of the sample was washed and dried up to 10 cycles to simulate a dynamic leaching attack. The two processes were followed by means of X-ray diffraction (XRD), pH and Cl- analyses in the simulated pore solution

  14. Conditions of k-struvite formation in magnesium phosphate cements

    International Nuclear Information System (INIS)

    Magnesium phosphate cements can be used as an alternative of Portland cements for the stabilization/solidification process of specific wastes like mercury, lead,... These cements are based on the reaction between magnesium oxide (MgO) and monopotassium phosphate (KH2PO4) mixed with water which leads to the formation of the solid skeleton of the matrix: MgO + KH2PO4 + 5H2O → MgKPO4.6H2O The development of k-struvite crystals (MgKPO4.6H2O) leads to the setting of these cements that have interesting properties for the stabilization/solidification of nuclear wastes: good chemical stability of the waste form, fast setting, low permeability, rapid compressive strength development. Still this novel material is not yet fully known, and its fast setting can be a drawback when it comes to large scale use. Thus, understanding the mechanisms of formation of k-struvite is important for a possible better control of the setting reaction. In this framework, the influence of pH and of the species in solution on the precipitation of k-struvite is studied. From pH and conductivity measurements of an MgO + KH2PO4 solution, it can be assumed that the k-struvite precipitation involves a precipitation and a dilution of an intermediate product: the newberyite (MgHPO4.3H2O). First newberyite (MgHPO4.3H2O) is formed, then with the pH rising, newberyite is dissolved and k-struvite will be able to crystallize. PH controlled precipitation, the XRD and DTA characterizations, and the supersaturation calculations confirm assumptions about the newberyite precipitation/dissolution mechanisms. (authors)

  15. Low temperature method for the production of calcium phosphate fillers

    Directory of Open Access Journals (Sweden)

    Nastro Alfonso

    2004-03-01

    Full Text Available Abstract Background Calcium phosphate manufactured samples, prepared with hydroxyapatite, are used as either spacers or fillers in orthopedic surgery, but these implants have never been used under conditions of mechanical stress. Similar conditions also apply with cements. Many authors have postulated that cements are a useful substitute material when implanted in vivo. The aim of this research is to develop a low cristalline material similar to bone in porosity and cristallinity. Methods Commercial hydroxyapatite (HAp and monetite (M powders are mixed with water and compacted to produce cylindrical samples. The material is processed at a temperature of 37–120 degrees C in saturated steam to obtain samples that are osteoconductive. The samples are studied by X-ray powder diffraction (XRD, Vickers hardness test (HV, scanning electron microscopy (SEM, and porosity evaluation. Results The X-ray diffractions of powders from the samples show patterns typical of HAp and M powders. After thermal treatment, no new crystal phase is formed and no increase of the relative intensity of the peaks is obtained. Vicker hardness data do not show any relationship with treatment temperature. The total porosity decreases by 50–60% according to the specific thermal treatment. Scanning electron microscopy of the surfaces of the samples with either HAp 80%-M 20% (c or Hap 50%-M 50% (f, show cohesion of the powder grains. Conclusions The dissolution-reprecipitation process is more intesive in manufactured samples (c and (f, according to Vickers hardness data. The process occurs in a steam saturated environment between 37 degrees and 120 degrees C. (c (f manufactured samples show pore dimension distributions useful to cellular repopulation in living tissues.

  16. Thermoluminescence in calcium phosphate doped with samarium

    International Nuclear Information System (INIS)

    Calcium phosphate is a main constitutional substance of human bones and teeth, and it seems worthwhile to investigate the thermoluminescence (TL) characteristics after X-ray irradiation at room temperature. It has been reported that there are two crystal modifications for the corresponding compounds, one rhombohedral and the other having a monoclinic lattice (α- and β-phase, respectively), and α-Ca3(PO4)2 is produced by heating the β-phase. However, it was rather difficult to get the former phase completely 100% from the latter only by heating. With the TL glow curves used for dosimetry it is generally required that a main isolated glow peak should be located at rather high-temperature regions, in order to avoid fading during the keeping of the irradiated materials at room temperature. It is the purpose of the present work to obtain a stable TL dosimeter peak by using β-Ca3(PO4)2, the raw material of which can be obtained directly from any chemical company. According to our preliminary experiments doping various activators into the β-Ca3(PO4)2, it was found that the addition of Sm2O3 into the raw material gives rise to a satisfactory result, and in this paper we describe the case in detail. (Author)

  17. 兔股骨节段缺损模型研究磷酸钙骨水泥骨愈合性能%Bone Healing Capacity of Calcium Phosphate Cement Cylinder in a Rabbit Femur Segmental Defect Model

    Institute of Scientific and Technical Information of China (English)

    王大伟; 潘朝晖; 赵玉祥; 栾兆新

    2015-01-01

    Objective:To investigate the bone healing capacity of calcium phosphate cement ( CPC) cylinder in a rabbit femur seg-mental defect model by comparing the influence of muscle or periosteum as wrapping material.Methods: Pre-hardened CPC cylinder was prepared.Three specimens were analyzed by scanning electron microscopy and X-ray diffraction to characterize its microstructure and chemical composition.Sixty adult rabbits were randomly assigned to four groups,then received a defect size of 15 mm osteotomy within the femurs.The 8-hole plate was fixed with three screws in the proximal and distal part of the defect, respectively.In group A, the fem-oral defects were left alone;in group B, the defects with retained periosteum; in group C, the defects were grafted with CPC cylinder wrapped by muscle;and in group D, the defects were grafted with CPC cylinder wrapped by periosteum.Five rabbits from each group were sacrificed at 4, 8 and 12 weeks postoperatively.The samples were evaluated with radiological, biomechanical and histological meth-ods.Results:Irregular particles were seen on the surface of specimens, the pore size was approximately 10 μm.The peak locations for the hydroxyapatite were seen in the X-ray diffraction patterns of the specimens.Group A showed a few radiographic evidence of new bone formation within the boundary of the defect at 4 weeks.Three bone defects bridged at 8 weeks and 4 bone defects bridged at 12 weeks. Group B showed radiographic evidence of new bone formation at 4 weeks.Four bone defects bridged at 8 weeks and 5 bone defects bridged at 12 weeks.Group C showed discernable interface between the CPC cylinder and both femoral cut ends at 4 weeks, which became invisi-ble at 8 weeks.Defects bridged by continuous callus beside the CPC cylinder in 4 rabbits and completely surrounded in 1 rabbit at 12 weeks.Group D showed better quality of new bone formation, the CPC cylinders were surrounded by new bone at 12 weeks.However, all CPCs retained their

  18. The Antimicrobial Action of Silver Halides in Calcium Phosphate

    OpenAIRE

    Kalniņa, D; Gross, K; Onufrijevs, P.; Daukšta, E; Nikolajeva, V; Stankeviciute, Z; Kareiva, A.

    2015-01-01

    Silver halides represent a yet unexplored avenue for imparting antimicrobial activity to calcium phosphates. Negtively charged silver halide colloids (AgI, AgBr and AgCl) were added to synthesized amorphous calcium phosphate. Concurrent melting of silver halides and crystallization to carbonated apatite at 700 oC increased the silver halide surface area available to bacteria and formed a lower solubility apatite. The effect of the matrix solubility on antimicrobial response could ...

  19. A review paper on biomimetic calcium phosphate coatings

    OpenAIRE

    Lin, X.; De Groot,, P.A.J.; Wang, D.; Hu, Q; Wismeijer, D.; Liu, Y

    2015-01-01

    Biomimetic calcium phosphate coatings have been developed for bone regeneration and repair because of their biocompatibility, osteoconductivity, and easy preparation. They can be rendered osteoinductive by incorporating an osteogenic agent, such as bone morphogenetic protein 2 (BMP-2), into the crystalline lattice work in physiological situations. The biomimetic calcium phosphate coating enables a controlled, slow and local release of BMP-2 when it undergoes cell mediated coating degradation ...

  20. Amorphous calcium phosphate composites with improved mechanical properties

    OpenAIRE

    O’Donnell, J.N.R.; Antonucci, J.M.; Skrtic, D.

    2006-01-01

    Hybridized zirconium amorphous calcium phosphate (ACP)-filled methacrylate composites make good calcium and phosphate releasing materials for anti-demineralizing/remineralizing applications with low mechanical demands. The objective of this study was to assess the effect of the particle size of the filler on the mechanical properties of these composites. Photo-curable resins were formulated from ethoxylated bisphenol A dimethacrylate, triethylene glycol dimethacrylate, 2-hydroxyethyl methacry...

  1. Calcium phosphate-based ceramic and composite materials for medicine

    International Nuclear Information System (INIS)

    The topical problems in chemistry and technology of materials based on calcium phosphates aimed at both the replacement of damaged bone tissue and its regeneration are discussed. Specific features of the synthesis of nanocrystalline powders and the fabrication of ceramic implants are described. Advances in the development of porous scaffolds from resorbable and osteoconductive calcium phosphates and of hybrid composites that form the basis of bone tissue engineering are considered.

  2. Biomechanical characteristics of calcium phosphate cement in the reinforcement of vertebral pedicle screw fixation%磷酸钙骨水泥强化椎弓根螺钉固定的生物力学特性

    Institute of Scientific and Technical Information of China (English)

    黎逢峰; 张庆宏; 黄野; 王云华

    2006-01-01

    组椎骨,用磷酸钙骨水泥重新固定12 h后拔松的椎弓根螺钉,测定其两侧的最大轴向拔出力.主要观察指标:①磷酸钙骨水泥最终凝固时强化椎弓根螺钉固定的生物力学测试结果.②磷酸钙骨水泥初步凝固时强化椎弓根螺钉固定的生物力学测试结果.③磷酸钙骨水泥强化松动椎弓根螺钉固定的生物力学测试结果.结果:①50岁组对照侧和强化侧的椎弓根螺钉最大轴向拔出力中位数分别为620 N和1 136 N,强化侧较对照侧增加83%(P<0.01).强化骨-螺钉界面的抗剪切应力中位数从1.16 N/mm2增加到2.13 N/mm2.②52岁组对照侧和强化侧的椎弓根螺钉最大轴向拔出力中位数分别为554.5 N和859.5 N,强化侧较对照侧增加55%(P<0.01).强化骨-螺钉界面的抗剪切应力中位数从1.039 N/mm2增加到1.61 N/mm2.③50岁组椎骨对照侧和强化侧重新固定12 h后最大轴向拔出力中位数分别为517 N和876 N,和同侧松动后轴向拔出力中位数比较,分别增加了63.6%和54.2%(P均<0.01).结论:磷酸钙骨水泥初步凝固和最终凝固时能强化椎弓根螺钉的固定,并且椎弓根螺钉松动后使用磷酸骨水泥能使螺钉重新获得固定.椎体强化侧的椎弓根螺钉均从骨-螺界面剥离开来,不伴周边骨质和椎弓根的严重损害,有利于螺钉松动、拔出后的二次置入.%BACKGROUND: Polymethylmethacrylate (PMMA) can ameliorate the condition between vertebral pedicle screws and peripheral bone-matrix interfaces and notably enhance the strength of screw fixation. However, there are several disadvantages during and after operation such as polymerized thermal damaging effect, toxicity and unabsorbable etc. Calcium phosphate cement (CPC) is biocompatible and biodegradable with good biosafty and produce no heat of polymerization, which is a perfect substitute for PMMA.OBJECTIVE: To evaluate the reinforcing effect of CPC on vertebral pedicle screw fixation at

  3. 以聚甲基丙烯酸甲酯为基质添加磷酸钙骨水泥在椎体成形术中的应用%APPLICATION OF USE OF PMMA AS MATRIX ADDED WITH CALCIUM PHOSPHATE CEMENT IN VERTEBROPLASTY

    Institute of Scientific and Technical Information of China (English)

    刘世军; 李俊霞; 程金生

    2011-01-01

    [目的]观察以聚甲基丙烯酸甲酯为基质添加磷酸钙骨水泥在椎体成形术中的应用价值,预防术后形成"空心椎"、"蛋壳椎"引起的椎体塌陷、后凸畸形.[方法]选取2007年7月~2009年8月住院椎体爆裂性骨折病人共15例患者,所有患者均行后路短阶段椎弓根内固定伤椎体成型术,以聚甲基丙烯酸甲酯为基质添加磷酸钙骨水泥填塞,随访10~15月.[结果]所有患者术中均没有发生脊髓损伤加重,无骨水泥外漏,伤椎恢复高度无明显丢失,无椎间隙塌陷.无内固定断裂或弯曲、松动.治疗前后两组相比差异有统计学意义(P<0.05).[结论]在短节段椎弓根复位固定后,应用聚甲基丙烯酸甲酯为基质添加磷酸钙骨水泥可即可恢复伤椎的强度和刚度,减少了后路内固定的应力,可早期下地活动,减少并发症,预防术后形成"空心椎"、"蛋壳椎"引起的椎体塌陷、后凸畸形.%[ Objective] To observe the value of PMMA matrix added with calcium phosphate cement in vertehroplasty,to prevent the vertebral collapse and kyphosis due to postoperative formation of "hollow venebrae" , "eggshell veflebral*.[Methods] From July 2007 to August 2009, 15 patients with burst fracture of vertebral body in our hospital underwent a short phase of posterior pedicle screw fixation injury vertebroplasty, in which polymethyl Methyl acrylate added with calcium phosphate cement as matrix was used to fill, then patients were followed up for 10 to 15 months. [Results] All patients were not found aggravating spinal cord injury dunng surgery, bone cement (t)eakage, obvious vertebral recovery height, disc space collapse, intemal fixation fracture or bending and loose. Compared two grroups before and after the treatment, there was statistically significant difference (P< 0.05). [Conclusion] In the short segment pedicle fixation, the application of PMMA added with calcium phosphate bone cement as matrix can restore

  4. Biomechanical evaluation of vertebroplasty using calcium sulfate cement for thoracolumbar burst fractures

    Institute of Scientific and Technical Information of China (English)

    WU Xiao-tao; JIANG Xing-jie; ZHANG Shao-dong; YANG Hui-lin

    2007-01-01

    Objective: To evaluate the biomechanical performance of vertebroplasty using calcium sulfate cement for thoracolumbar burst fractures.Methods: Sixteen bovine thoracolumbar spines (T11-L1 ) were divided into 4 groups (A, B, C and D). After burst-fracture model was created, 12 vertebral bodies in Groups A, B and C were augmented with calcium sulfate cement (CSC), calcium phosphate cement (CPC) and polymethylmethacrylate ( PMMA ) bone cement,respectively. Each anterior vertebral body height was measured with a caliper at 4 time points: intact conditions(HInt), post-fracture (HFr), post-reduction (HRe) and post-vertebroplasty (HVP). The filling volume of 3 different bone cements was also measured. Each vertebral body was compressed at 0.5 mm/s using a hinged plating system on a materials testing machine to 50% of the postvertebroplasty height to determine strength and stiffness.Difference was checked using t test or One-way ANOVA.Results: The average strike energy was 66. 2 J.Vertebroplasty with different cements could sustain vertebral height. The average filling volume of bone cement in 3 groups was 4.35 ml (CSC), 3.72 ml (CPC) and 3.95 ml (PMMA), respectively, and there was no statistically significant difference among them ( P >0.05).Vertebroplasty with PMMA completely restored strength(116%) and stiffness (105%). CSC or CPC partly recovered vertebral strength and stiffness. However,greater strength restoration was got with CSC ( 1 659 N) as compared with CPC (1 011N, P<0.01 ). Regarding stiffness, differences between CSC (140 N/mm ±40 N/mm)and the other two bone cements ( CPC :148 N/mm ±33 N/mm,PMMA:236 N/mm ±97 N/mm) were not significant (P>0.05).Conclusions: For a burst-fracture of calf spine, useof CSC for vertebroplasty yields similar vertebral stiffnessas compared with PMMA or CPC. Although augmentationwith CSC partly obtains the normal strength, thistreatment still can be applied in thoracolumbar burstfractures with other instrumental devices in

  5. Dentin-cement Interfacial Interaction: Calcium Silicates and Polyalkenoates

    OpenAIRE

    Atmeh, A.R.; Chong, E. Z.; Richard, G; Festy, F.; Watson, T.F.

    2012-01-01

    The interfacial properties of a new calcium-silicate-based coronal restorative material (Biodentine™) and a glass-ionomer cement (GIC) with dentin have been studied by confocal laser scanning microscopy (CLSM), scanning electron microscopy (SEM), micro-Raman spectroscopy, and two-photon auto-fluorescence and second-harmonic-generation (SHG) imaging. Results indicate the formation of tag-like structures alongside an interfacial layer called the “mineral infiltration zone”, where the alkaline c...

  6. Calcium Sulfoaluminate Eco-Cement from Industrial Waste

    OpenAIRE

    Ukrainczyk, N.; Frankoviæ Mihelj, N.; Šipušić, J.

    2013-01-01

    In this paper, the potential benefits offered by calcium sulfoaluminate cement (CSA) production from industrial wastes or by-products already present in Republic of Croatia have been addressed. A variety of industrial wastes, namely phosphogypsum (PG), coal bottom ash (BA) and electric arc furnace slag (EAFS) were used as raw materials to provide additional environmental advantages in production of CSA. Mass fraction of Ye’elimite, the principal hydraulic mineral in the prepared CSA was de...

  7. Furcal perforation repair using calcium enriched mixture cement

    OpenAIRE

    Asgary Saeed

    2010-01-01

    This case describes a furcal perforation in a mandibular first molar accompanied by furcal lesion which has been managed after one month. Root canal treatment was performed; subsequently, the defect was repaired with calcium enriched mixture (CEM) cement. The endodontically treated tooth was restored with amalgam. A 24-month recall showed no evidence of periodontal breakdown, no symptoms, in addition to completes healing of furcal lesion. According to physical and biological properties of the...

  8. Calcium Aluminate based Cement as Dental Restorative Materials

    OpenAIRE

    Kraft, Lars

    2002-01-01

    This thesis presents the results from the development process of a ceramic dental filling material based on calcium aluminate cement. The main focus of the work concerns dimensional changes during setting, hardening and curing and the understanding of the factors controlling the dimensional stability of the system. A range of compositions for research purposes and the composition of Doxadent™ – a dental product launched on the Swedish market in October 2000 – were evaluated. Furthermore hardn...

  9. Effect of humic substances on the precipitation of calcium phosphate

    Institute of Scientific and Technical Information of China (English)

    SONG Yong-hui; Hermann H. HAHN; Erhard HOFFMANN; Peter G. WEIDLER

    2006-01-01

    For phosphorus (P) recovery from wastewater, the effect of humic substances (HS) on the precipitation of calcium phosphate was studied. Batch experiments of calcium phosphate precipitation were undertaken with synthetic water that contained 20 mg/L phosphate (as P) and 20 mg/L HS (as dissolved organic carbon, DOC) at a constant pH value in the range of 8.0-10.0. The concentration variations of phosphate, calcium (Ca) and HS were measured in the precipitation process; the crystalline state and compositions of the precipitates were analysed by powder X-ray diffraction (XRD) and chemical methods, respectively. It showed that at solution pH 8.0, the precipitation rate and removal efficiency of phosphate were greatly reduced by HS, but at solution pH ≥9.0,the effect of HS was very small. The Ca consumption for the precipitation of phosphate increased when HS was added; HS was also removed from solution with the precipitation of calcium phosphate. At solution pH 8.0 and HS concentrations ≤ 3.5 mg/L, and at pH ≥ 9.0 and HS concentrations ≤ 10 mg/L, the final precipitates were proved to be hydroxyapatite (HAP) by XRD. The increases of solution pH value and initial Ca/P ratio helped reduce the influence of HS on the precipitation of phosphate.

  10. Post cementation sensitivity evaluation of glass Ionomer, zinc phosphate and resin modified glass Ionomer luting cements under class II inlays: An in vivo comparative study

    OpenAIRE

    Chandrasekhar, V.

    2010-01-01

    Objective: This study aims to compare the patient-perceived post-cementation sensitivity of class II metal restorations preoperatively, immediately after cementation, one week after cementation and one month after cementation with (1) Glass Ionomer luting cement (2) Zinc Phosphate cement and (3) Resin-modified Glass Ionomer luting cement. Materials and Methods: A total of 60 patients, irrespective of sex, in the age group of 15-50 years were selected and the teeth were randomly divided into t...

  11. Aqueous deposition of calcium phosphates and silicate substituted calcium phosphates on magnesium alloys

    International Nuclear Information System (INIS)

    Attempts were made to deposit homogeneous films of calcium phosphates (CaPs) on two magnesium alloy systems, AZ31 and Mg–4Y, through an aqueous phosphating bath method. The deposition of silicate substituted CaPs by this aqueous method was also explored as silicate substitution is believed to increase the bioactivity of CaPs. The effect of doped and undoped coatings on the in vitro degradation and bioactivity of both alloy systems was studied. FTIR and EDX confirmed the deposition of Ca, P, and Si on both alloys and the coatings appeared to consist primarily biphasic mixtures of hydroxyapatite and β-TCP. These largely inhomogeneous coatings, as observed by SEM, were not shown to have any significant effect on maintaining the physiological pH of the culture medium in comparison to the uncoated samples, as the pH remained approximately in the 8.4–8.7 range. Interestingly, despite similar pH profiles between the coated and uncoated samples, CaP coatings affected the degradation of both alloys. These doped and undoped calcium phosphate coatings were observed to decrease the degradation of AZ31 whereas they increased the degradation of Mg–4Y. In vitro studies on cell attachment using MC3T3-E1 mouse osteoblasts showed that between the uncoated alloys, Mg–4Y appeared to be the more biocompatible of the two. Silicate substituted CaP coatings were observed to increase the cell attachment on AZ31 compared to bare and undoped CaPs coated samples, but did not have as great of an effect on increasing cell attachment on Mg–4Y.

  12. Identification of the hydrate gel phases present in phosphate-modified calcium aluminate binders

    International Nuclear Information System (INIS)

    The conversion of hexagonal calcium aluminate hydrates to cubic phases in hydrated calcium aluminate cements (CAC) can involve undesirable porosity changes and loss of strength. Modification of CAC by phosphate addition avoids conversion, by altering the nature of the reaction products, yielding a stable amorphous gel instead of the usual crystalline hydrate products. Here, details of the environments of aluminium and phosphorus in this gel were elucidated using solid-state NMR and complementary techniques. Aluminium is identified in both octahedral and tetrahedral coordination states, and phosphorus is present in hydrous environments with varying, but mostly low, degrees of crosslinking. A 31P/27Al rotational echo adiabatic passage double resonance (REAPDOR) experiment showed the existence of aluminium–phosphorus interactions, confirming the formation of a hydrated calcium aluminophosphate gel as a key component of the binding phase. This resolves previous disagreements in the literature regarding the nature of the disordered products forming in this system

  13. Identification of the hydrate gel phases present in phosphate-modified calcium aluminate binders

    Energy Technology Data Exchange (ETDEWEB)

    Chavda, Mehul A.; Bernal, Susan A. [Department of Materials Science and Engineering, The University of Sheffield, Sheffield S1 3JD (United Kingdom); Apperley, David C. [Solid-State NMR Group, Department of Chemistry, Durham University, Durham DH1 3LE (United Kingdom); Kinoshita, Hajime [Department of Materials Science and Engineering, The University of Sheffield, Sheffield S1 3JD (United Kingdom); Provis, John L., E-mail: j.provis@sheffield.ac.uk [Department of Materials Science and Engineering, The University of Sheffield, Sheffield S1 3JD (United Kingdom)

    2015-04-15

    The conversion of hexagonal calcium aluminate hydrates to cubic phases in hydrated calcium aluminate cements (CAC) can involve undesirable porosity changes and loss of strength. Modification of CAC by phosphate addition avoids conversion, by altering the nature of the reaction products, yielding a stable amorphous gel instead of the usual crystalline hydrate products. Here, details of the environments of aluminium and phosphorus in this gel were elucidated using solid-state NMR and complementary techniques. Aluminium is identified in both octahedral and tetrahedral coordination states, and phosphorus is present in hydrous environments with varying, but mostly low, degrees of crosslinking. A {sup 31}P/{sup 27}Al rotational echo adiabatic passage double resonance (REAPDOR) experiment showed the existence of aluminium–phosphorus interactions, confirming the formation of a hydrated calcium aluminophosphate gel as a key component of the binding phase. This resolves previous disagreements in the literature regarding the nature of the disordered products forming in this system.

  14. Investigation of calcium phosphate coatings for biomedical applications

    International Nuclear Information System (INIS)

    Calcium phosphate is the main constituent of our bone and tooth minerals. The use of this bioactive material for coating implant such as artificial joint prosthesis, therefore, can promote biological fixation and enhance biocompatibility. Our initial work has been focused on the evaluation of experimental conditions of coating preparation and the effects of post-deposition calcium phosphate coatings on stainless steel substrates. The coating layers were produced by the precipitation technique and coatings were carried out in sol-gel by the dipping method. For comparison purposes a wet method was used to obtain a fine calcium phosphate ceramic powder for fabrication of microcrystal suspension used as a coating material. Scanning electron microscopy (SEM), energy dispersive microanalysis (EDS), energy dispersive x-ray fluorescence (EDXRF) and x-ray diffraction (XRD) were used to characterise the morphology, chemical composition and structure of the coatings. The results showed that the dip coating of stainless steel substrates using viscous solutions lead to the formation of porous calcium phosphate layers. These results suggested that fabrication of bioactive calcium phosphate coatings using this route offers significant advantages over the currently used methods due to considerably lower temperature process involved and may produce better result for substrates with complex shapes

  15. Characterization of dicalcium phosphate dihydrate cements prepared using a novel hydroxyapatite-based formulation

    International Nuclear Information System (INIS)

    Dicalcium phosphate dihydrate (DCPD) cements are typically prepared using β-tricalcium phosphate (β-TCP) as the base component. However, hydroxyapatite (HA) is an interesting alternative because of its potential for reducing cement acidity, as well as modulating cement properties via ionic substitutions. In the present study, we have characterized DCPD cements prepared with a novel formulation based on monocalcium phosphate monohydrate (MCPM) and HA. Cements were prepared using a 4:1 MCPM:HA molar ratio. The reactivity of HA in this system was verified by showing DCPD formation using poorly crystalline HA, as well as highly crystalline HA. Evaluation of cements prepared with poorly crystalline HA revealed that setting occurs rapidly in the MCPM/HA system, and that the use of a setting regulator is necessary to maintain workability of the cement paste. Compressive testing showed that MCPM/HA cements have strengths comparable to what has previously been published for DCPD cements. However, preliminary in vitro analysis of cement degradation revealed that conversion of DCPD to HA may occur much more rapidly in the MCPM/HA system compared to cements prepared with β-TCP. Future studies should investigate this property further, as it could have important implications for the use of HA-based DCPD cement formulations.

  16. Calcium phosphate bioceramics prepared from wet chemically precipitated powders

    Directory of Open Access Journals (Sweden)

    Kristine Salma

    2010-03-01

    Full Text Available In this work calcium phosphates were synthesized by modified wet chemical precipitation route. Contrary to the conventional chemical precipitation route calcium hydroxide was homogenized with planetary mill. Milling calcium oxide and water in planetary ball mill as a first step of synthesis provides a highly dispersed calcium hydroxide suspension. The aim of this work was to study the influence of main processing parameters of wet chemical precipitation synthesis product and to control the morphology, phase and functional group composition and, consequently, thermal stability and microstructure of calcium phosphate bioceramics after thermal treatment. The results showed that it is possible to obtain calcium phosphates with different and reproducible phase compositions after thermal processing (hydroxyapatite [HAp], β-tricalcium phosphate [β-TCP] and HAp/β-TCP by modified wet-chemical precipitation route. The β-TCP phase content in sintered bioceramics samples is found to be highly dependent on the changes in technological parameters and it can be controlled with ending pH, synthesis temperature and thermal treatment. Pure, crystalline and highly thermally stable (up to 1300°C HAp bioceramics with homogenous grainy microstructure, grain size up to 200–250 nm and high open porosity can be successfully obtained by powder synthesized at elevated synthesis temperature of 70°C and stabilizing ending pH at 9.

  17. Calcium-phosphate-osteopontin particles for caries control

    DEFF Research Database (Denmark)

    Schlafer, Sebastian; Birkedal, Henrik; Olsen, Jakob;

    2016-01-01

    Caries is caused by acid production in biofilms on dental surfaces. Preventing caries therefore involves control of microorganisms and/or the acid produced. Here, calcium-phosphate-osteopontin particles are presented as a new approach to caries control. The particles are made by co-precipitation ......Caries is caused by acid production in biofilms on dental surfaces. Preventing caries therefore involves control of microorganisms and/or the acid produced. Here, calcium-phosphate-osteopontin particles are presented as a new approach to caries control. The particles are made by co......, and the pH always remained above 5.5. Hence, calcium-phosphate-osteopontin particles show potential for applications in caries control....

  18. Casein Phosphopeptide- Amorphous Calcium Phosphate in Dentistry: A Literature Review

    OpenAIRE

    KESKİN, Arş. Gör. Dt. Gül; GÜLER, Yrd. Doç. Dr. Çiğdem

    2013-01-01

    Casein is a phosphoprotein in bovine milk and accounts for almost 80 percent of its total protein. Casein fosfopeptit (CPP) is produced as a result of decomposition of casein with trypsin enzyme using a selective deposition method. CPP can remarkably stabilize calcium phosphate in a state-forming CPPamorphous calcium phosphate (ACP) complex. CPPACP is located in topical gels, sugar-free chewing gum and mint dragees at the present day. In this paper, the effectiveness of CPP-ACP and usage in d...

  19. Calcium-phosphate-osteopontin particles for caries control

    DEFF Research Database (Denmark)

    Schlafer, Sebastian

    Oftentimes caries lesions develop in protected sites that are difficult to access by self-performed mechanical tooth cleaning. At present, there is a growing interest in chemical adjuncts to mechanical procedures of oral hygiene that aim at biofilm control rather than biofilm eradication. Calcium...... drops to 6 or below and release buffering phosphate ions that stabilize biofilm pH above the critical level for enamel dissolution. With that twofold approach, calcium-phosphate-osteopontin particles may make a relevant contribution to clinical caries control....

  20. Optimization of calcium phosphate fine ceramic powders preparation

    Science.gov (United States)

    Sezanova, K.; Tepavitcharova, S.; Rabadjieva, D.; Gergulova, R.; Ilieva, R.

    2013-12-01

    The effect of biomimetic synthesis method, reaction medium and further precursor treatments on the chemical and phase composition, crystal size and morphology of calcium phosphates was examined. Nanosized calcium phosphate precursors were biomimetically precipitated by the method of continuous precipitation in three types of reaction media at pH 8: (i) SBF as an inorganic electrolyte system; (ii) organic (glycerine) modified SBF (volume ratio of 1:1); (iii) polymer (10 g/l xanthan gum or 10 g/l guar gum) modified SBF (volume ratio of 1:1). After maturation (24 h) the samples were lyophilized, calcinated at 300°C for 3 hours, and washed with water, followed by new gelation, lyophilization and step-wise (200, 400, 600, 800, and 1000°C, each for 3 hours) sintering. The reaction medium influenced the chemical composition and particle size but not the morphology of the calcium phosphate powders. In all studied cases bi-phase calcium phosphate fine powders with well-shaped spherical grains, consisting of β-tricalcium phosphate (β-TCP) and hydroxyapatite (HA) with a Ca/P ratio of 1.3 - 1.6 were obtained. The SBF modifiers decreased the particle size of the product in the sequence guar gum ˜ xanthan gum < glycerin < SBF medium.

  1. Synthesis and characterization of zirconium-doped calcium phosphate biomaterial

    International Nuclear Information System (INIS)

    A new synthesis route for the production of calcium phosphate biomaterial was developed by using organic di-(2-ethylhexyl) phosphoric acid (DEHPA) mixed with calcium hydroxide slurry. Unlike the conventional involving chemical precipitation process this new method involves a sol-gel process. Another advantage of this method is the starting material DEHPA can form strong bonding with many elements including zirconium and rare earths. This makes it suitable to be used as drug delivery material especially those involving bone related disease. It also improves the biomaterial strength with the presence of zirconium oxide phase. From XRD analysis, the result shows the present of HA, α-TCP and β-TCP. The addition of different rare elements on to the calcium phosphate will varies the amount of these three phases. SEM analysis was also performed to study the morphology of the calcium phosphate material. The presence of the rare earths on to the calcium phosphate was established by using the EDS technique. (Author)

  2. Casein Phosphopeptide-Amorphous Calcium Phosphate Nanocomplexes: A Structural Model.

    Science.gov (United States)

    Cross, Keith J; Huq, N Laila; Reynolds, Eric C

    2016-08-01

    Tryptic digestion of the calcium-sensitive caseins yields casein phosphopeptides (CPP) that contain clusters of phosphorylated seryl residues. The CPP stabilize calcium and phosphate ions through the formation of complexes. The calcium phosphate in these complexes is biologically available for intestinal absorption and remineralization of subsurface lesions in tooth enamel. We have studied the structure of the complexes formed by the CPP with calcium phosphate using a variety of nuclear magnetic resonance (NMR) techniques. Translational diffusion measurements indicated that the β-CN(1-25)-ACP nanocomplex has a hydrodynamic radius of 1.526 ± 0.044 nm at pH 6.0, which increases to 1.923 ± 0.082 nm at pH 9.0. (1)H NMR spectra were well resolved, and (3)JH(N)-H(α) measurements ranged from a low of 5.5 Hz to a high of 8.1 Hz. Total correlation spectroscopy and nuclear Overhauser effect spectroscopy spectra were acquired and sequentially assigned. Experiments described in this paper have allowed the development of a structural model of the β-CN(1-25)-amorphous calcium phosphate nanocomplex. PMID:27434168

  3. Rickets induced by calcium or phosphate depletion.

    OpenAIRE

    Abugassa, S.; Svensson, O.

    1990-01-01

    We studied the effects of calciopenia and phosphopenia on longitudinal growth, skeletal mineralization, and development of rickets in young Sprague-Dawley rats. At an age of 21 days, two experimental groups were given diets containing 0.02% calcium or 0.02% phosphorus; otherwise the diets were nutritionally adequate. After 7, 14, and 21 days, five animals from each group were randomly chosen. The animals were anaesthetized and blood samples were drawn for analysis of calcium, phosphorus, and ...

  4. Reactions of fly ash with calcium aluminate cement and calcium sulphate

    OpenAIRE

    Fernández Carrasco, Lucía; Vázquez Ramonich, Enric

    2009-01-01

    The hydration processes in the ternary system fly ash/calcium aluminate cement/calcium sulphate (FA/CAC/C$) at 20 °C were investigated; six compositions from the ternary system FA/CAC/C$ were selected for this study. The nature of the reaction products in these pastes were analysed by X-ray diffraction (XRD) and infrared spectroscopy (FTIR). At four days reaction time, the main hydration reaction product in these pastes was ettringite and the samples with major initial CAC presented minor ett...

  5. Another look at the deterioration of calcium aluminate cement concrete

    Directory of Open Access Journals (Sweden)

    Jambor, Jaromir

    1996-03-01

    Full Text Available Potential degradation of concrete structures made of calcium aluminate cement (CAC is well known and is caused by transformation (conversion of the thermodynamically metastable into stable calcium aluminate hydrate phases. This recrystallization is influenced by temperature and humidity; the structural degradation of the concrete itself thus its loss of strength, is strongly related to the pore structure of the hydrated cement paste, the critical parameters being the total volume of pores below 15-20 nm and the median micropore radius. This constitutes a novel procedure for evaluation of existing CAC concrete structure.

    La degradación potencial de estructuras de hormigón elaboradas con cemento aluminoso (CA es bien conocida. Este deterioro está causado por la recristalización (conversión de las fases del aluminato cálcico que son termodinámicamente metastables, en fases estables. En esta recristalización influye la temperatura y la humedad. Tanto la degradación del propio hormigón, como su pérdida de resistencias están relacionadas estrechamente con la estructura porosa de la pasta del cemento hidratado, siendo parámetros críticos el volumen total de los poros inferiores a 15-20 nm y el tamaño medio de los radios de los microporos. Esto constituye un nuevo procedimiento para evaluar las estructuras existentes de hormigón de cemento aluminoso (CA.

  6. Tri-calcium phosphate (ß-TCP) can be artificially synthesized by recycling dihydrate gypsum hardened.

    Science.gov (United States)

    Han-Cheol, Cho; Hori, Masaharu; Yoshida, Takakazu; Yamada, Naoko; Komada, Yuko; Tamaki, Yukimichi; Miyazaki, Takashi

    2014-01-01

    Calcium phosphate is known as a major component of biological hard tissues. This study aimed to produce calcium phosphate by recycling kneaded surplus gypsum. β-dihydrate gypsum was derived from commercial dental β-hemihydrate gypsum, which was mechanically powdered and mixed with the liquid component of a commercial zinc phosphate cement. This mixture was fired at 1,200°C and evaluated by XRD analysis, thermal analysis and scanning electron microscopy (SEM). An acceptable ratio of mixing was 4 g of β-dihydrate gypsum powder to 1.5 mL of phosphoric acid liquid. XRD peaks were monotonic below 800°C, but new ß-TCP was formed by firing at 900°C or more, although TG-DTA analysis of synthetic ß-TCP suggested that some residual dihydrate gypsum remained in the sample. SEM images indicated a fused-block bone-like structure covered with phosphorus and calcium. These results suggest that production of synthetic β-TCP is possible through ecological techniques using recycled materials. PMID:25483384

  7. Calcium and phosphate homeostasis: concerted interplay of new regulators.

    NARCIS (Netherlands)

    Renkema, K.Y.R.; Alexander, R.T.; Bindels, R.J.M.; Hoenderop, J.G.J.

    2008-01-01

    Calcium (Ca(2+)) and phosphate (P(i)) are essential to many vital physiological processes. Consequently the maintenance of Ca(2+) and P(i) homeostasis is essential to a healthy existence. This occurs through the concerted action of intestinal, renal, and skeletal regulatory mechanisms. Ca(2+) and P(

  8. Biomimetic calcium phosphate coatings on recombinant spider silk fibres

    Energy Technology Data Exchange (ETDEWEB)

    Yang Liang; Habibovic, Pamela; Van Blitterswijk, Clemens A [Department of Tissue Regeneration, University of Twente, PO Box 217, 7500 AE Enschede (Netherlands); Hedhammar, My; Johansson, Jan [Department of Anatomy, Physiology and Biochemistry, Swedish University of Agricultural Sciences, the Biomedical Centre, Box 575, 751 23 Uppsala (Sweden); Blom, Tobias; Leifer, Klaus [Department of Engineering Sciences, Uppsala University, Box 534, S-751 21 Uppsala (Sweden)

    2010-08-01

    Calcium phosphate ceramic coatings, applied on surfaces of metallic and polymeric biomaterials, can improve their performance in bone repair and regeneration. Spider silk is biocompatible, strong and elastic, and hence an attractive biomaterial for applications in connective tissue repair. Recently, artificial spider silk, with mechanical and structural characteristics similar to those of native spider silk, has been produced from recombinant minispidroins. In the present study, supersaturated simulated body fluid was used to deposit calcium phosphate coatings on recombinant spider silk fibres. The mineralization process was followed in time using scanning electron microscopy equipped with an energy dispersive x-ray (EDX) detector and Raman spectroscope. Focused ion beam technology was used to produce a cross section of a coated fibre, which was further analysed by EDX. Preliminary in vitro experiments using a culture of bone marrow-derived human mesenchymal stem cells (hMSCs) on coated fibres were also performed. This study showed that recombinant spider silk fibres were successfully coated with a homogeneous and thick crystalline calcium phosphate layer. In the course of the mineralization process from modified simulated body fluid, sodium chloride crystals were first deposited on the silk surface, followed by the deposition of a calcium phosphate layer. The coated silk fibres supported the attachment and growth of hMSCs.

  9. Mechanical properties of porous, electrosprayed calcium phosphate coatings

    NARCIS (Netherlands)

    Leeuwenburgh, S.C.G.; Wolke, J.G.C.; Lommen, L.; Pooters, T.; Schoonman, J.; Jansen, J.A.

    2006-01-01

    Mechanical properties of calcium phosphate coatings (CaP), deposited using the electrostatic spray deposition (ESD) technique, have been characterized using a range of analytical techniques, including tensile testing (ASTM C633), fatigue testing (ASTM E855), and scratch testing using blunt and sharp

  10. Biomimetic calcium phosphate coatings on recombinant spider silk fibres

    International Nuclear Information System (INIS)

    Calcium phosphate ceramic coatings, applied on surfaces of metallic and polymeric biomaterials, can improve their performance in bone repair and regeneration. Spider silk is biocompatible, strong and elastic, and hence an attractive biomaterial for applications in connective tissue repair. Recently, artificial spider silk, with mechanical and structural characteristics similar to those of native spider silk, has been produced from recombinant minispidroins. In the present study, supersaturated simulated body fluid was used to deposit calcium phosphate coatings on recombinant spider silk fibres. The mineralization process was followed in time using scanning electron microscopy equipped with an energy dispersive x-ray (EDX) detector and Raman spectroscope. Focused ion beam technology was used to produce a cross section of a coated fibre, which was further analysed by EDX. Preliminary in vitro experiments using a culture of bone marrow-derived human mesenchymal stem cells (hMSCs) on coated fibres were also performed. This study showed that recombinant spider silk fibres were successfully coated with a homogeneous and thick crystalline calcium phosphate layer. In the course of the mineralization process from modified simulated body fluid, sodium chloride crystals were first deposited on the silk surface, followed by the deposition of a calcium phosphate layer. The coated silk fibres supported the attachment and growth of hMSCs.

  11. Osteoinduction of calcium phosphate biomaterials in small animals

    International Nuclear Information System (INIS)

    Although osteoinduction mechanism of calcium phosphate (CP) ceramics is still unclear, several essential properties have been reported, such as chemical composition, pore size and porosity, etc. In this study, calcium phosphate powder (Ca3(PO4)2, CaP, group 1), biphasic calcium phosphate ceramic powder (BCP, group 2), and intact BCP rods (group 3) were implanted into leg muscles of mice and dorsal muscles of rabbits. One month and three months after implantation, samples were harvested for biological and histological analysis. New bone tissues were observed in 10/10 samples in group 1, 3/10 samples in group 2, and 9/10 samples in group 3 at 3rd month in mice, but not in rabbits. In vitro, human mesenchymal stem cells (hMSCs) were cultured with trace CaP and BCP powder, and osteogenic differentiation was observed at day 7. Our results suggested that chemical composition is the prerequisite in osteoinduction, and pore structure would contribute to more bone formation. - Highlights: ► Intrinsic osteoinduction of calcium phosphate biomaterials was observed implanted in muscles of mice. ► Biomaterials powder also has osteoinduction property. ► Osteogenic genes and protein could be detected by RT-PCR and Western blot in implanted biomaterials. ► Osteogenic phenomenon could be observed by electron microscopy. ► The chemical composition is the prerequisite in osteoinduction, and pore structure would contribute to more bone formation

  12. Amorphous calcium phosphate and its application in dentistry

    Directory of Open Access Journals (Sweden)

    Sun Wei-bin

    2011-07-01

    Full Text Available Abstract Amorphous Calcium Phosphate (ACP is an essential mineral phase formed in mineralized tissues and the first commercial product as artificial hydroxyapatite. ACP is unique among all forms of calcium phosphates in that it lacks long-range, periodic atomic scale order of crystalline calcium phosphates. The X-ray diffraction pattern is broad and diffuse with a maximum at 25 degree 2 theta, and no other different features compared with well-crystallized hydroxyapatite. Under electron microscopy, its morphological form is shown as small spheroidal particles in the scale of tenths nanometer. In aqueous media, ACP is easily transformed into crystalline phases such as octacalcium phosphate and apatite due to the growing of microcrystalline. It has been demonstrated that ACP has better osteoconductivity and biodegradability than tricalcium phosphate and hydroxyapatite in vivo. Moreover, it can increase alkaline phosphatase activities of mesoblasts, enhance cell proliferation and promote cell adhesion. The unique role of ACP during the formation of mineralized tissues makes it a promising candidate material for tissue repair and regeneration. ACP may also be a potential remineralizing agent in dental applications. Recently developed ACP-filled bioactive composites are believed to be effective anti-demineralizing/remineralizing agents for the preservation and repair of tooth structures. This review provides an overview of the development, structure, chemical composition, morphological characterization, phase transformation and biomedical application of ACP in dentistry.

  13. Magnetic properties study on Fe-doped calcium phosphate

    Science.gov (United States)

    Silva, C. C.; Vasconcelos, I. F.; Sombra, A. S. B.; Valente, M. A.

    2009-11-01

    Calcium phosphates are very important for applications in medicine due to their properties such as biocompatibility and bioactivity. In order to enhance these properties, substitution of calcium with other ions has been proposed. Partial substitution of calcium by different ions has been made in order to improve the properties of the calcium phosphates and also to allow new applications of apatite in medicine. In this work, hydroxyapatite [Ca10(PO4)6(OH)2—HAP] was prepared by high-energy dry milling (20 h) and mixed with iron oxide (5 wt.%). The mixture was calcinated at 900 °C for 5 h with a heating rate of 3 °C min-1 in an attempt to introduce iron oxide into the HAP structure. The sintered sample was characterized using x-ray diffraction (XRD) and magnetization. The 57Fe-Mössbauer spectra of the calcium phosphate oxides were also measured, revealing the presence of iron in three different phases: Ca2Fe2O5, Fe2O3 and hydroxyapatite.

  14. Formation of calcium phosphate mineral materialcontrolled by microemulsion

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In order to prepare calcium phosphate-based material with nano-structure and bioactivity, natural lecithin and n-tetradecane were used as the amphipile and the oil phase respectively, along with the water phase, to form a microemulsion template. Phosphate mineralization was induced and controlled by the microemulsion. The products, characterized by scanning electronic microscopy, infrared spectroscopy and X-ray diffraction analysis, are composed of lecithin and hydroxyapatite, and possess the nano-structure of sticks, balls and three-dimensional nets connected by tubes. These results show that the microemulsion can be used to control calcium phosphate mineralization for the preparation of biomimetic mineral materials with various nano-structures.

  15. Kebaikan Dan Keburukan Zinc Phosphate Cement Serta Penggunaannya Dalam Bidang kedokteran Gigi

    OpenAIRE

    Ramses Ricardo B.

    2008-01-01

    Salah satu jenis semen yang paling sering digunakan dalam bidang kedokteran gigi adalah Zinc Phosphate Cement. Komposisinya terdiri dan bubuk dan cairan yang akan dicampur pacta glass slab untuk mendapatkan kekentalan yang tepat. Semen ini memiliki beberapa kebaikan dan keburukan yang saling mempengaruhi dan hal ini pula yang membuat semen ini masih tetap dipergunakan sampai saat ini di klinik. Zinc Phosphate Cement memiliki sifat mekanis, khususnya Compressive Strength yang sangat baik....

  16. Cytotoxic effects of mineral trioxide aggregate, calcium enrichedmixture cement, Biodentine and octacalcium pohosphate onhuman gingival fibroblasts

    Science.gov (United States)

    A. Saberi, Eshagh; Farhadmollashahi, Narges; Ghotbi, Faroogh; Karkeabadi, Hamed; Havaei, Roholla

    2016-01-01

    Background. This in vitro study compared the effects of mineral trioxide aggregate (MTA), calcium enriched mixture(CEM) cement, Biodentine (BD) and octacalcium phosphate (OCP) on the viability of human gingival fibroblasts (HGFs). Methods. After completion of the setting time of the materials under study, fibroblasts were placed in 24-well insert platesand 1 mg of each material was added to the respective wells. The plates were then incubated at 37°C. The inserts were removedat 24, 48 and 168 hours and 2,5-diphenyltetrazolium bromide was added to assess cytotoxicity via the MTT colorimetricassay. Data were analyzed at different time intervals using repeated-measures ANOVA, followed by the Bonferronitest at three levels of significance of P MTA (P MTA, CEM, Biodentine and OCP against HGFs was similar to that of the control group at 24and 48 hours. Over time, MTA and Biodentine exhibited less cytotoxicity than other materials. PMID:27429722

  17. Optimization of calcium chloride content on bioactivity and mechanical properties of white Portland cement

    International Nuclear Information System (INIS)

    This research investigates the optimization of calcium chloride content on the bioactivity and mechanical properties of white Portland cement. Calcium chloride was used as an addition of White Portland cement at 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10% by weight. Calcium chloride was dissolved in sterile distilled water and blended with White Portland cement using a water to cement ratio of 0.5. Analysis of the bioactivity and pH of white Portland cement pastes with calcium chloride added at various amounts was carried out in simulated body fluid. Setting time, density, compressive strength and volume of permeable voids were also investigated. The characteristics of cement pastes were examined by X-ray diffractometer and scanning electron microscope linked to an energy-dispersive X-ray analyzer. The result indicated that the addition of calcium chloride could accelerate the hydration of white Portland cement, resulting in a decrease in setting time and an increase in early strength of the pastes. The compressive strength of all cement pastes with added calcium chloride was higher than that of the pure cement paste, and the addition of calcium chloride at 8 wt.% led to achieving the highest strength. Furthermore, white Portland cement pastes both with and without calcium chloride showed well-established bioactivity with respect to the formation of a hydroxyapatite layer on the material within 7 days following immersion in simulated body fluid; white Portland cement paste with added 3%CaCl2 exhibited the best bioactivity. - Highlights: ► Optimization CaCl2 content on the bioactivity and mechanical properties. ► CaCl2 was used as an addition at 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10% by weight. ► CaCl2 resulted in a decrease in setting time and an increase in early strength. ► Addition of 3%CaCl2 exhibited the optimum formation of hydroxyapatite.

  18. Influence of calcium on ceramide-1-phosphate monolayers.

    Science.gov (United States)

    Oliveira, Joana S L; Brezesinski, Gerald; Hill, Alexandra; Gericke, Arne

    2016-01-01

    Ceramide-1-phosphate (C1P) plays an important role in several biological processes, being identified as a key regulator of many protein functions. For instance, it acts as a mediator of inflammatory responses. The mediation of the inflammation process happens due to the interaction of C1P with the C2 domain of cPLA2α, an effector protein that needs the presence of submicromolar concentrations of calcium ions. The aim of this study was to determine the phase behaviour and structural properties of C1P in the presence and absence of millimolar quantities of calcium in a well-defined pH environment. For that purpose, we used monomolecular films of C1P at the soft air/liquid interface with calcium ions in the subphase. The pH was varied to change the protonation degree of the C1P head group. We used surface pressure versus molecular area isotherms coupled with other monolayer techniques as Brewster angle microscopy (BAM), infrared reflection-absorption spectroscopy (IRRAS) and grazing incidence X-ray diffraction (GIXD). The isotherms indicate that C1P monolayers are in a condensed state in the presence of calcium ions, regardless of the pH. At higher pH without calcium ions, the monolayer is in a liquid-expanded state due to repulsion between the negatively charged phosphate groups of the C1P molecules. When divalent calcium ions are added, they are able to bridge the highly charged phosphate groups, enhancing the regular arrangement of the head groups. Similar solidification of the monolayer structure can be seen in the presence of a 150 times larger concentration of monovalent sodium ions. Therefore, calcium ions have clearly a strong affinity for the phosphomonoester of C1P. PMID:26977381

  19. Minimally Invasive Pedicle Screw Fixation Combined with Vertebroplasty with Calcium Phosphate Bone Cement in the Treatment of Thoracolumbar Burst Fracture%微创椎弓根钉内固定联合磷酸钙骨水泥椎体成形术治疗胸腰椎爆裂性骨折

    Institute of Scientific and Technical Information of China (English)

    顾宇彤; 梁朝革; 张亮; 林红; 周健

    2015-01-01

    目的:评估微创椎弓根钉内固定(微小切口非空心椎弓根钉技术)联合磷酸钙骨水泥经皮穿刺椎体成形术(percutaneous vertebroplasty ,PVP)治疗胸腰椎爆裂性骨折的疗性和安全性。方法:采用微创椎弓根钉内固定联合磷酸钙骨水泥 PVP术治疗23例单节段胸腰椎新鲜爆裂性骨折且无神经症状的患者,伤椎位于 T11~L2,均属A3型骨折。记录手术时间、术中出血量、骨水泥注射量和住院天数。记录术前及术后即刻、1个月、2个月、3个月、6个月、1年、2年的腰背痛评分,计算并比较各时点的椎体高度压缩率、恢复率、椎体后凸角、椎体后凸矫正率。结果:磷酸钙骨水泥平均注射量为4.9(3.8~6.4)mL,平均手术时间92(75~120) min ,平均出血量52(40~75) mL ,平均住院5.6(4~7) d ,术后平均随访26(24~29)个月。VAS评分由术前的(8.8±1.2)分下降至术后即刻的(1.8±0.6)分及术后2年的(0.4±0.5)分,差异均有显著统计学意义(P<0.001)。高度压缩率由术前的(50.4±7.2)%显著下降至术后即刻的(6.2±1.5)%及术后2年的(6.9±1.4)%,差异均有显著统计学意义(P<0.001)。后凸角由术前的(22.6±1.8)°下降至术后即刻的(3.2±1.7)°及术后2年的(5.1±1.5)°,差异均有显著统计学意义( P<0.001)。随访过程中术后高度恢复率、后凸矫正率无明显减小;未出现螺钉松动、断钉或断棒。结论:微创椎弓根钉内固定联合磷酸钙骨水泥PV P术是治疗胸腰椎爆裂性骨折的安全、有效的方法。%Objective:To evaluate the efficacy and safety of minimally invasive pedicle screw fixation combined with percutaneous vertebroplasty(PVP) with calcium phosphate bone cement in the treatment of acute thoracolumbar burst fracture . Methods:Twenty‐three patients

  20. Hydration studies of calcium sulfoaluminate cements blended with fly ash

    International Nuclear Information System (INIS)

    The main objective of this work is to study the hydration and properties of calcium sulfoaluminate cement pastes blended with fly ash (FA) and the corresponding mortars at different hydration ages. Laboratory X-ray powder diffraction, rheological studies, thermal analysis, porosimetry and compressive strength measurements were performed. The analysis of the diffraction data by Rietveld method allowed quantifying crystalline phases and overall amorphous contents. The studied parameters were: i) FA content, 0, 15 and 30 wt.%; and ii) water addition, water-to-CSA mass ratio (w/CSA = 0.50 and 0.65), and water-to-binder mass ratio (w/b = 0.50). Finally, compressive strengths after 6 months of 0 and 15 wt.% FA [w/CSA = 0.50] mortars were similar: 73 ± 2 and 72 ± 3 MPa, respectively. This is justified by the filler effect of the FA as no strong evidences of reactivity of FA with CSA were observed. These results support the partial substitution of CSA cements with FA with the economic and environmental benefits

  1. Hydration studies of calcium sulfoaluminate cements blended with fly ash

    Energy Technology Data Exchange (ETDEWEB)

    García-Maté, M.; De la Torre, A.G. [Departamento de Química Inorgánica, Cristalografía y Mineralogía, Universidad de Málaga, 29071 Málaga (Spain); León-Reina, L. [Servicios Centrales de Apoyo a la Investigación, Universidad de Málaga, 29071 Málaga (Spain); Aranda, M.A.G. [Departamento de Química Inorgánica, Cristalografía y Mineralogía, Universidad de Málaga, 29071 Málaga (Spain); CELLS-Alba synchrotron, Carretera BP 1413, Km. 3.3, E-08290 Cerdanyola, Barcelona (Spain); Santacruz, I., E-mail: isantacruz@uma.es [Departamento de Química Inorgánica, Cristalografía y Mineralogía, Universidad de Málaga, 29071 Málaga (Spain)

    2013-12-15

    The main objective of this work is to study the hydration and properties of calcium sulfoaluminate cement pastes blended with fly ash (FA) and the corresponding mortars at different hydration ages. Laboratory X-ray powder diffraction, rheological studies, thermal analysis, porosimetry and compressive strength measurements were performed. The analysis of the diffraction data by Rietveld method allowed quantifying crystalline phases and overall amorphous contents. The studied parameters were: i) FA content, 0, 15 and 30 wt.%; and ii) water addition, water-to-CSA mass ratio (w/CSA = 0.50 and 0.65), and water-to-binder mass ratio (w/b = 0.50). Finally, compressive strengths after 6 months of 0 and 15 wt.% FA [w/CSA = 0.50] mortars were similar: 73 ± 2 and 72 ± 3 MPa, respectively. This is justified by the filler effect of the FA as no strong evidences of reactivity of FA with CSA were observed. These results support the partial substitution of CSA cements with FA with the economic and environmental benefits.

  2. Synthesis optimization of calcium aluminate cement phases for biomedical applications

    International Nuclear Information System (INIS)

    Calcium aluminate cement (CAC) has been studied as a potential material for applications in the areas of health such as, endodontics and bone reconstruction. These studies have been based on commercial products consisting of a mixture of phases. Improvements can be attained by investigating the synthesis routes of CAC aiming the proper balance between the phases and the control of impurities that may impair its performance for biomedical applications. Thus, the aim of this work was to study the CAC synthesis routes in the Al2O3-CaCO3 and Al2O3-CaO systems, as well as the phase characterization attained by means of X ray analysis. The Al2O3-CaO route enabled the production of the target phases (CA, CA2, C3A and C12A7) with a higher purity compared to the Al2O3-CaCO3 one. As a result the particular properties of these phases can be evaluated to define a more suitable composition that results in better properties for an endodontic cement and other applications. (author)

  3. The nucleation and growth of calcium phosphate crystals at protein and phosphatidylserine liposome surfaces.

    Science.gov (United States)

    Nancollas, G H; Tsortos, A; Zieba, A

    1996-01-01

    The kinetics of calcium phosphate crystal growth at the surfaces of proteins and phospholipids has been investigated using free drift and constant composition methods in supersaturated calcium phosphate solutions (relative supersaturations: with respect to hydroxyapatite, HAP, sigma HAP = 15.0, and with respect to octacalcium phosphate, OCP, sigma OCP = 1.9). Fibrinogen and collagen molecules adsorbed at hydrophobic surfaces as well as uncross-linked collagen fibrils induce ion binding and subsequent nucleation of calcium phosphate. The formation of OCP on phosphatidylserine vesicles introduced to highly supersaturated calcium phosphate solutions probably involves the interaction of the calcium ions with the ionized carboxylic groups of the phospholipid. PMID:9813627

  4. The role of polycarboxylic acids in calcium phosphate mineralization.

    Science.gov (United States)

    Tsortos, Achilles; Nancollas, George H

    2002-06-01

    The role of two polyelectrolytes, poly-L-glutamate and poly-L-aspartate, in the growth of calcium phosphate crystal phases, has been investigated at constant supersaturation. Both molecules are strong inhibitors of HAP growth when present in the solution phase but also act as hydroxyapatite and (octacalcium phosphate)-like crystal nucleators when adsorbed on germanium surfaces. The structure of the polymers in solution is presented and various adsorption models are analyzed. A "train-loop" structure of these long, flexible chain polymers on the crystal surface is consistent with all the adsorption (experimental and theoretical), inhibition, and electrophoretic mobility results. PMID:16290647

  5. Acid gelation of colloidal calcium phosphate-depleted preheated milk

    OpenAIRE

    Famelart, Marie-Hélène; Gauvin, Géraldine; Paquet, Denis; Brulé, Gérard

    2009-01-01

    Abstract – This study aimed at understanding the role of colloidal calcium phosphate (CCP) in acid gelation of milk. Milks were depleted in Calcium (Ca) by dialysis against milk permeate containing a cation-exchange resin. Dialysed milks were then heated (90 °C-10 min) and acidgelled at 42 °C with a yoghurt culture. Minerals, total and soluble protein contents, pH and optical density were measured in unheated and heated dialysed milk, together with diameters and ζ-potentials of particles. Dia...

  6. Use of zinc phosphate cement as a luting agent for Denzir™ copings: an in vitro study

    Directory of Open Access Journals (Sweden)

    Mondragon Eduardo

    2003-02-01

    Full Text Available Abstract Background The clinical success rate with zinc phosphate cemented Procera crowns is high. The objective with this study was to determine whether CADCAM processed and zinc phosphate cemented Denzir copings would perform as well as zinc phosphate cemented Procera copings when tested in vitro in tension. Methods Twelve Procera copings and twenty-four Denzir copings were made. After the copings had been made, twelve of the Denzir copings were sandblasted on their internal surfaces. All copings were then cemented with zinc phosphate cement to carbon steel dies and transferred to water or artificial saliva. Two weeks after cementation, half of the samples were tested. The remaining samples were tested after one year in the storage medium. All tests were done in tension and evaluated with an ANOVA. Results Sandblasted and un-sandblasted Denzir copings performed as well as Procera copings. Storage in water or artificial saliva up to one year did not decrease the force needed to dislodge any of the coping groups. Three copings fractured during testing and one coping developed a crack during testing. The three complete fractures occurred in Procera copings, while the partly cracked coping was a Denzir coping. Conclusion No significant differences existed between the different material groups, and the retentive force increased rather than decreased with time. Fewer fractures occurred in Denzir copings, explained by the higher fracture toughness of the Denzir material. Based on good clinical results with zinc phosphate cemented Procera crowns, we foresee that zinc phosphate cement luted Denzir copings are likely to perform well clinically.

  7. Subcutaneous ectopic osteogenesis induced by porous calcium phosphate cement and gelatin sponge as the carrier of recombinant bone morphogenetic protein-2 in rats:A comparative study%两种材料复合rhBMP-2诱导大鼠皮下异位成骨的比较研究

    Institute of Scientific and Technical Information of China (English)

    李想; 董纪元; 彭江; 汪爱媛; 睢翔; 赵斌; 刘道宏

    2011-01-01

    Objective To analyze the difference in subcutaneous ectopic osteogenesis induced by porous calcium phosphate cement (CPC) and gelatin sponge as a carrier of recombinant bone morphogenetic protein-2 (rhBMP-2). Methods Thirty Sprague Dawley rats with an average body weight of 200g were divided into groups A-D. CPC+rhBMP-2, CPC, gelatin sponge+rhBMP-2, and gelatin sponge were implanted into the rats after anesthesia. Ten rats were killed 2, 4 and 8 weeks after they were fed under sterile environment. Bone tissue samples were collected from the implantation sites. Tissue mineral density (TMD) and trabecular thickness were detected with micro-CT scanner and analyzed with SPSS 1 OX) statistical software. Bone tissue was fixed in 4% paraformaldehyde for 2 days, embedded in paraffin, and cut into sections. The sections were stained with H&E to observe their histological change. Results The tissue mineral density and trabecular thickness of the samples with rhBMP-2 were higher in two experimental groups 2,4 and 8 weeks after implantation, which increased with the prolongation of time (P<0.05). Conclusion Porous CPC can be used as a carrier of rhBMP-2 for osteogenesis.%目的 分析多孔自固化磷酸钙骨水泥(Calcium Phosphate Cement,CPC)和明胶海绵复合重组人骨形态发生蛋白(Recombinantion Humen Bone Morphogenetic Protein-2,rhBMP-2)诱导大鼠皮下异位成骨的区别.方法 平均质量200g SD大鼠30只,麻醉后分别植入A:多孔CPC复合rhBMP-2(2μg);B:多孔CPC;C:明胶海绵复合rhBMP-2(2μg);D:空白明胶海绵,无菌喂养后分别于2、4、8周各处死10只.对植入部位组织取材,分别进行micro-CT扫描,并使用Micview V2.1三维重建处理软件扫及ABA骨形态分析软件检测,记录组织骨密度(Tissue Mineral Density,TMD)及骨小梁厚度(Trabecular Thickness,Tb.Th).运用SPSS10.0统计软件进行统计学分析.后行甲醛固定2周,石蜡包埋切片,HE染色进行组织学观察.结果 在2、4、8

  8. Mechanism of calcium phosphates precipitation in liquid crystals; Mecanisme de precipitation de phosphates de calcium dans des cristaux liquides

    Energy Technology Data Exchange (ETDEWEB)

    Prelot, B.; Zemb, T

    2004-04-01

    The possibility of using as a precursor an easily wet meso-porous powder would be a breakthrough in the preparation of nuclear waste storage ceramics. A concentrated solution containing ions to be stored would wet a dry powder and then, subjected to mild compression, lead to a micro-crystalline matrix of calcium phosphate at acceptable temperatures. Since no porous calcium phosphate different from calcined bone (patented) is described as porous precursor, we have compared the different synthesis routes towards meso-porous ceramics. First, we considered homogeneous precipitation of slats in water: using initially off-stoichiometry in reaction, micron-sized hydroxyapatite particles are produced with a specific surface up to 100 m{sup 2}/g. Then, we consider the classical route of precipitation of an hybrid material in the miscibility gap of a phase diagram, when an hexagonal liquid crystal is used a matrix for precipitation. The surfactant family consists in single chain surfactants containing phosphates as head-group to poison the growing surface of calcium phosphate nano-domains. Since the reaction is still too brutal, we considered using a cat-anionic precursor material of controllable surface charge. For certain concentrations and molar ratios, a new structure not yet described in surfactant precipitation literature is observed: since the periodicity is lower than twice the chain length, a disordered constant curvature monolayer (instead of the classical cylinder of twice chain length diameter) of surfactant is implied. Finally, we have investigated synthesis routes implying slow dissolution of pre-formed calcium phosphate in an already existing hexagonal matrix. For all these routes of synthesis, micro-structural determinations using SAXS, WARS and BET are performed, with a special attention to comparison of the precipitation material, the matrix obtained with all elements present, and also the material obtained after calcinations. (authors)

  9. 3D Computational Simulation of Calcium Leaching in Cement Matrices

    Directory of Open Access Journals (Sweden)

    Gaitero, J. J.

    2014-12-01

    Full Text Available Calcium leaching is a degradation process consisting in progressive dissolution of the cement paste by migration of calcium atoms to the aggressive solution. It is therefore, a complex phenomenon involving several phases and dissolution and diffusion processes simultaneously. Along this work, a new computational scheme for the simulation of the degradation process in three dimensions was developed and tested. The toolkit was used to simulate accelerated calcium leaching by a 6M ammonium nitrate solution in cement matrices. The obtained outputs were the three dimensional representation of the matrix and the physicochemical properties of individual phases as a consequence of the degradation process. This not only makes it possible to study the evolution of such properties as a function of time but also as a function of the position within the matrix. The obtained results are in good agreement with experimental values of the elastic modulus in degraded and undegraded samples.El lixiviado de calcio es un proceso de degradación consistente en la disolución progresiva de la pasta de cemento por la migración de los átomos de calcio a la disolución agresiva. Se trata por tanto de un fenómeno complejo que involucra simultáneamente diferentes fases y procesos de disolución y difusión. En este trabajo se desarrolló y probó una nueva herramienta computacional para la simulación del proceso de degradación en tres dimensiones. Para ello se simuló el lixiviado de calcio acelerado provocado por una disolución de nitrato amónico 6M en matrices de cemento. Como resultado se obtuvieron la representación tridimensional de la matriz y las propiedades físico-químicas sus fases a lo largo del tiempo. Esto permitió estudiar la evolución de dichas propiedades a lo largo del proceso de degradación así como en función de su posición dentro de la matriz. Los resultados obtenidos coinciden con los valores experimentales del módulo elástico tanto

  10. Aggregation of Calcium Phosphate and Oxalate Phases in the Formation of Renal Stones

    OpenAIRE

    Xie, Baoquan; Halter, Timothy J.; Borah, Ballav M.; Nancollas, George H.

    2014-01-01

    The majority of human kidney stones are comprised of multiple calcium oxalate monohydrate (COM) crystals encasing a calcium phosphate nucleus. The physiochemical mechanism of nephrolithiasis has not been well determined on the molecular level; this is crucial to the control and prevention of renal stone formation. This work investigates the role of phosphate ions on the formation of calcium oxalate stones; recent work has identified amorphous calcium phosphate (ACP) as a rapidly forming initi...

  11. Formation and thermal studies of calcium phosphate glasses

    International Nuclear Information System (INIS)

    Calcium Phosphate based glasses and glass ceramics are known for their bio- active nature. Thermal behaviour of three compositions of CaO-Na/sub 2/O-SiO/sub 2/-P/sub 2/O/sub 5/ glass system were studied. All glasses were clear and stable. Characteristic temperatures i.e. glass transition, glass softening temperature and liquids temperatures were determined by differential thermal analyzer and dilatometer. (author)

  12. Remineralization of Demineralized Enamel via Calcium Phosphate Nanocomposite

    OpenAIRE

    Weir, M.D.; Chow, L.C.; Xu, H.H.K.

    2012-01-01

    Secondary caries remains the main problem limiting the longevity of composite restorations. The objective of this study was to investigate the remineralization of demineralized human enamel in vitro via a nanocomposite containing nanoparticles of amorphous calcium phosphate (NACP). NACP were synthesized by a spray-drying technique and incorporated into a dental resin. First, caries-like subsurface enamel lesions were created via an acidic solution. Then, NACP nanocomposite or a commercial flu...

  13. The influence of Sr content in calcium phosphate coatings

    International Nuclear Information System (INIS)

    In this study calcium phosphate coatings with different amounts of strontium (Sr) were prepared using a biomineralization method. The incorporation of Sr changed the composition and morphology of coatings from plate-like to sphere-like morphology. Dissolution testing indicated that the solubility of the coatings increased with increased Sr concentration. Evaluation of extracts (with Sr concentrations ranging from 0 to 2.37 μg/mL) from the HA, 0.06Sr, 0.6Sr, and 1.2Sr coatings during in vitro cell cultures showed that Sr incorporation into coatings significantly enhanced the ALP activity in comparison to cells treated with control and HA eluted media. These findings show that calcium phosphate coatings could promote osteogenic differentiation even in a low amount of strontium. - Highlights: • Calcium phosphate coating doping with low Sr contents was prepared via a biomineralization process. • The solubility of the coatings increased with increased Sr concentration. • Present findings show the potential that Sr has on promoting osteogenic differentiation even in a low amount

  14. Synthesis of hollow spherical calcium phosphate nanoparticles using polymeric nanotemplates

    International Nuclear Information System (INIS)

    Poly(methylmethacrylate)-block-poly(methacrylic acid) (PMMA-b-PMAA) copolymer was synthesized by an atom transfer radical polymerization (ATRP) technique. The block copolymer was employed as a template for the controlled precipitation of calcium phosphate from aqueous solution at different pH values. A Ca2+ ion selective electrode was used to study the interactions between Ca2+ ions and the polymer, which indicated a possible weak interaction between Ca2+ and un-ionized MAA segments at pH∼4.0 in addition to electrostatic interaction between Ca2+ and ionized MAA segments at higher pH. An interesting structure representing that of a superstructure consisting of hybrid nano-filaments was observed by the transmission electron microscope at pH∼4.0. The filaments originated from a core of similar size to primary polymer aggregates, suggesting that cooperative interactions at a local level between dissolving calcium phosphate clusters and disassembling polymer segments are responsible for the secondary growth process. A hollow spherical morphology was obtained at pH∼7.0 and 9.0. Such calcium phosphate/polymer monohybrids with complex morphologies are interesting and might be useful as novel drug delivery carriers, ceramics precursors, reinforcing fillers or biomedical implants

  15. Protein Adsorption of Calcium Phosphate Ceramics in vitro

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    In order to provide valuable information for the design of new calcium phosphate bone repair materials, bone tissue engineering scaffold materials, and other clinical application, the interaction between calcium phosphate materials and proteins were investigated. The adsorption of the calcium phosphate ceramic to the protein was investigated by using FT- IR, XPS, SEM, and SDS- PAGE. As the results shown, the proteins were strongly adsorbed by the CPC, and a shift of the feature peak of the protein and also a chemical shift in the Ca2p and O1s bind energy of CPC was observed. This indicated that the acidic amino-group and alkaline amino- residue on the proteins' surface bonded to the Ca2 + in the β- TCP crystal by ionic bond and the proteins' alkaline amino groups to the oxygen in PO3-4 by hydrogen bond and electrostatic attraction. The adsorption mechanism of the protein in the CPC can be described as three ndsorption layers: irreversible chemical adsorption layer, physical adsorption layer and biomineralized adsorption layer.

  16. The influence of Sr content in calcium phosphate coatings

    Energy Technology Data Exchange (ETDEWEB)

    Lindahl, Carl [Department of Biomaterials, Institute for Clinical Sciences, Sahlgrenska Academy at the University of Gothenburg, Gothenburg (Sweden); BIOMATCELL, VINN Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Pujari-Palmer, Shiuli; Hoess, Andreas; Ott, Marjam [Applied Materials Science, Department of Engineering Sciences, Uppsala University, Uppsala (Sweden); Engqvist, Håkan [BIOMATCELL, VINN Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Applied Materials Science, Department of Engineering Sciences, Uppsala University, Uppsala (Sweden); Xia, Wei, E-mail: wei.xia@angstrom.uu.se [BIOMATCELL, VINN Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Applied Materials Science, Department of Engineering Sciences, Uppsala University, Uppsala (Sweden)

    2015-08-01

    In this study calcium phosphate coatings with different amounts of strontium (Sr) were prepared using a biomineralization method. The incorporation of Sr changed the composition and morphology of coatings from plate-like to sphere-like morphology. Dissolution testing indicated that the solubility of the coatings increased with increased Sr concentration. Evaluation of extracts (with Sr concentrations ranging from 0 to 2.37 μg/mL) from the HA, 0.06Sr, 0.6Sr, and 1.2Sr coatings during in vitro cell cultures showed that Sr incorporation into coatings significantly enhanced the ALP activity in comparison to cells treated with control and HA eluted media. These findings show that calcium phosphate coatings could promote osteogenic differentiation even in a low amount of strontium. - Highlights: • Calcium phosphate coating doping with low Sr contents was prepared via a biomineralization process. • The solubility of the coatings increased with increased Sr concentration. • Present findings show the potential that Sr has on promoting osteogenic differentiation even in a low amount.

  17. Characterization and biocompatibility of fluoridated biphasic calcium phosphate ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Z.L. [State Key Laboratory of Oral Diseases, West China Hospital of Stomatology, Sichuan University, Chengdu 610041 (China); Yu, H.Y. [State Key Laboratory of Oral Diseases, West China Hospital of Stomatology, Sichuan University, Chengdu 610041 (China)], E-mail: yhyang6812@tfol.com; Zeng, Q. [Institute for Nanobiomedical Technology and Membrane Biology, Sichuan University, Chengdu 610041 (China); He, H.W. [State Key Laboratory of Oral Diseases, West China Hospital of Stomatology, Sichuan University, Chengdu 610041 (China)

    2008-11-15

    Biphasic calcium phosphate ceramics (BCP) has been widely used in tooth and bone implants due to its excellent biocompatibility. Incorporation of fluorine ions in BCP has drawn much attention because of the beneficial role played by the fluorine ions in bone and tooth growth. The aim of this study was to obtain fluoridated biphasic calcium phosphate (FBCP) by immersing BCP into saturated ZnF{sub 2} solution with F{sup -} concentration of 3500 mg/l at different times. The phase and incorporation of fluoride into BCP were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM). The biomineralization and influence of FBCP on osteoblastic behavior were evaluated and compared with that of biphasic calcium phosphate (BCP). The results exhibited that the phase evolution of the BCP was affected by the fluoride incorporation and the FBCP significantly improved the differentiation and proliferation of osteoblasts. These findings suggest that the FBCP would be very useful as a bone reconstructive material.

  18. Cementation of Radioactive Waste from a PWR with Calcium Sulfoaluminate Cement

    International Nuclear Information System (INIS)

    Spent radioactive ion-exchange resin (SIER) and evaporation concentrates are radioactive wastes that are produced at by pressurized water reactor (PWR) nuclear power stations. Borate, which is used as a retardent for cement, is also present as a moderator in a PWR, therefore, borate will be present in both ion-exchange resins and evaporation concentrates. In this study the use of Calcium sulfoaluminate cements (SAC) as encapsulation medium for these waste streams was investigated. The study involved the manufacturing of different cement test samples with different amounts of SAC cement, waste resins (50% water content) and admixtures. In order to reduce hydration heat during 200 L solidification experiments, different admixtures were investigated. Initial results based on compressive strength tests and hydration temperature studies, indicated that zeolite was the best admixture for the current waste form. Experiments indicated that the addition of resin material into the current cement matrix reduces the hydration heat during curing Experimental results indicated that a combination of SAC (35 wt. %), zeolite (7 wt. %) mix with 42 wt. % resins (50% water content) and 16 wt. % of water forms a optimum cured monolith with low hydration heat. The microstructures of hydrated OPC, SAC and SAC with zeolite addition were studied using a Scanning Electron Microscopy (SEM). SEM results indicated that the SAC matrices consist of a needle type structure that changed gradually into a flake type structure with the addition of zeolite. Additionally, the presence of zeolite material inside the SAC matrix reduced the leaching rates of radionuclides significantly. In a final 200 L grouting test, measured results indicated a hydration temperature below 90oC withno thermal cracks after solidified. The influence of radiation on the compressive strength and possible gas generation (due to radiolysis) on cement waste forms containing different concentrations ion exchange resin was

  19. Performance characteristics of concrete based on a ternary calcium sulfoaluminate–anhydrite–fly ash cement

    OpenAIRE

    Ioannou, Socrates; Paine, Kevin; Reig Cerdá, Lucía; Quillin, Keith

    2015-01-01

    This paper reports an assessment of the performance of concrete based on a calcium sulfoaluminate–anhydrite–fly ash cement combination. Concretes were prepared at three different w/c ratios and the properties were compared to those of Portland cement and blast-furnace cement concretes. The assessment involved determination of mechanical and durability properties. The results suggest that an advantageous synergistic effect between and ettringite and fly ash (Ioannou et al., 2014) was reflected...

  20. In Vitro Cytotoxicity of Calcium Silicate-Based Endodontic Cement as Root-End Filling Materials

    OpenAIRE

    Selen Küçükkaya; Mehmet Ömer Görduysus; Naciye Dilara Zeybek; Sevda Fatma Müftüoğlu

    2016-01-01

    The aim of this study was to evaluate the cytotoxicity of three types of calcium silicate-based endodontic cement after different incubation periods with human periodontal ligament fibroblasts. Human periodontal ligament fibroblasts were cultured from extracted third molars and seeded in 96-well plates. MTA, calcium enriched mixture (CEM) cement, and Biodentine were prepared and added to culture insert plates which were immediately placed into 96-well plates containing cultured cells. After i...

  1. Calcium phosphate granulation in anaerobic treatment of black water: a new approach to phosphorus recovery

    NARCIS (Netherlands)

    Tervahauta, T.H.; Weijden, van der R.D.; Flemming, R.L.; Hernández, L.; Zeeman, G.; Buisman, C.J.N.

    2014-01-01

    Recovery of phosphorus from wastewater as calcium phosphate could diminish the need for mining of scarce phosphate rock resources. This study introduces a novel approach to phosphorus recovery by precipitation of calcium phosphate granules in anaerobic treatment of black water. The granules formed i

  2. Direct 3D powder printing of biphasic calcium phosphate scaffolds for substitution of complex bone defects

    International Nuclear Information System (INIS)

    The 3D printing technique based on cement powders is an excellent method for the fabrication of individual and complex bone substitutes even in the case of large defects. The outstanding bone remodeling capacity of biphasic calcium phosphates (BCPs) containing hydroxyapatite (HA) as well as tricalcium phosphate (TCP) in varying ratios makes the adaption of powder systems resulting in BCP materials to this fabrication technique a desirable aim. This study presents the synthesis and characterization of a novel powder system for the 3D printing process, intended for the production of complexly shaped BCP scaffolds by a hydraulic setting reaction of calcium carbonate and TCP with phosphoric acid. The HA/TCP ratio in the specimens could be tailored by the calcium/phosphate ratio of the starting powder. The scaffolds could be fabricated with a dimensional accuracy of >96.5% and a minimal macro pore size of 300 µm. Independent of the phase composition the printed specimens showed a microporosity of approximately 68%, while the compressive strength strongly depended on the chemical composition and increased with rising TCP content in the scaffolds to a maximum of 1.81 MPa. Post-treatment of the scaffolds with a polylactic-co-glycolic acid-solution enhanced the mechanical properties by a factor of 8. In vitro studies showed that all BCP scaffolds were cytocompatible and enhanced the cell viability as well as the cell proliferation, as compared with pure TCP. Cell proliferation is even better on BCP when compared to HA and cell viability is in a similar range on these materials. (paper)

  3. BLENDED CALCIUM ALUMINATE-CALCIUM SULFATE CEMENT-BASED GROUT FOR P-REACTOR VESSEL IN-SITU DECOMMISSIONING

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C.; Stefanko, D.

    2011-03-10

    The objective of this report is to document laboratory testing of blended calcium aluminate - calcium hemihydrate grouts for P-Reactor vessel in-situ decommissioning. Blended calcium aluminate - calcium hemihydrate cement-based grout was identified as candidate material for filling (physically stabilizing) the 105-P Reactor vessel (RV) because it is less alkaline than portland cement-based grout which has a pH greater than 12.4. In addition, blended calcium aluminate - calcium hemihydrate cement compositions can be formulated such that the primary cementitious phase is a stable crystalline material. A less alkaline material (pH {<=} 10.5) was desired to address a potential materials compatibility issue caused by corrosion of aluminum metal in highly alkaline environments such as that encountered in portland cement grouts [Wiersma, 2009a and b, Wiersma, 2010, and Serrato and Langton, 2010]. Information concerning access points into the P-Reactor vessel and amount of aluminum metal in the vessel is provided elsewhere [Griffin, 2010, Stefanko, 2009 and Wiersma, 2009 and 2010, Bobbitt, 2010, respectively]. Radiolysis calculations are also provided in a separate document [Reyes-Jimenez, 2010].

  4. Blended Calcium Aluminate-Calcium Sulfate Cement-Based Grout For P-Reactor Vessel In-Situ Decommissioning

    International Nuclear Information System (INIS)

    The objective of this report is to document laboratory testing of blended calcium aluminate - calcium hemihydrate grouts for P-Reactor vessel in-situ decommissioning. Blended calcium aluminate - calcium hemihydrate cement-based grout was identified as candidate material for filling (physically stabilizing) the 105-P Reactor vessel (RV) because it is less alkaline than portland cement-based grout which has a pH greater than 12.4. In addition, blended calcium aluminate - calcium hemihydrate cement compositions can be formulated such that the primary cementitious phase is a stable crystalline material. A less alkaline material (pH ≤ 10.5) was desired to address a potential materials compatibility issue caused by corrosion of aluminum metal in highly alkaline environments such as that encountered in portland cement grouts (Wiersma, 2009a and b, Wiersma, 2010, and Serrato and Langton, 2010). Information concerning access points into the P-Reactor vessel and amount of aluminum metal in the vessel is provided elsewhere (Griffin, 2010, Stefanko, 2009 and Wiersma, 2009 and 2010, Bobbitt, 2010, respectively). Radiolysis calculations are also provided in a separate document (Reyes-Jimenez, 2010).

  5. Calcium phosphates in Ca(2+)-fortified milk: phase identification and quantification by Raman spectroscopy.

    Science.gov (United States)

    Arifin, Martha; Swedlund, Peter J; Hemar, Yacine; McKinnon, Ian R

    2014-12-17

    Calcium phosphate nanoclusters (CPNs) are important for the structure, function, and nutrient density of many dairy products. Phosphorylated amino acids in caseins stabilize calcium phosphate as nanoclusters which are amorphous to X-ray diffraction and exist within casein micelles, and these CPNs play a key role in micelle stability. Addition of calcium to milk results in further calcium phosphate removal from the serum, and there is uncertainty about the nature of the material formed and its stability. In this work we investigate both the solution and colloidal phases in CaCl2 enriched bovine milk to identify, quantify, and determine the solubility of the calcium phosphate material formed in response to calcium addition to milk. The P-O stretching bands are quite distinct in the Raman spectra of the main synthetic calcium phosphate mineral phases, including the amorphous calcium phosphate phase. In response to adding between 5 and 40 mM CaCl2 to milk, the serum phosphate concentration decreased asymptotically from 7.5 ± 0.2 to 0.54 ± 0.05 mM. Using Raman spectroscopy with a combination of internal and external standards, it was possible to show that the calcium phosphate material formed after Ca(2+) addition to milk was the same as amorphous calcium phosphate nanoclusters present in the absence of added calcium. The use of an internal standard allowed a quantitative analysis of the spectra which demonstrated that the amorphous calcium phosphate formed accounted for all of the calcium and phosphate that was removed from solution in response to calcium addition. PMID:25414967

  6. Calcium-phosphate-osteopontin particles for caries control.

    Science.gov (United States)

    Schlafer, Sebastian; Birkedal, Henrik; Olsen, Jakob; Skovgaard, Jonas; Sutherland, Duncan S; Wejse, Peter L; Nyvad, Bente; Meyer, Rikke L

    2016-01-01

    Caries is caused by acid production in biofilms on dental surfaces. Preventing caries therefore involves control of microorganisms and/or the acid produced. Here, calcium-phosphate-osteopontin particles are presented as a new approach to caries control. The particles are made by co-precipitation and designed to bind to bacteria in biofilms, impede biofilm build-up without killing the microflora, and release phosphate ions to buffer bacterial acid production if the pH decreases below 6. Analysis of biofilm formation and pH in a five-species biofilm model for dental caries showed that treatment with particles or pure osteopontin led to less biofilm formation compared to untreated controls or biofilms treated with osteopontin-free particles. The anti-biofilm effect can thus be ascribed to osteopontin. The particles also led to a slower acidification of the biofilm after exposure to glucose, and the pH always remained above 5.5. Hence, calcium-phosphate-osteopontin particles show potential for applications in caries control. PMID:26923119

  7. Kinetics of dissolution of calcium phosphate (Ca-P bioceramics

    Directory of Open Access Journals (Sweden)

    Lukas Brazda

    2008-06-01

    Full Text Available Hydroxyapatite (HAp and β-tricalcium phosphate (β-TCP are widely used bioceramics for surgical or dental applications. This paper is dealing with dissolution kinetics of synthetically prepared β-TCP and four types of HAp granules. Two groups of HAp, treated at different temperatures, each of them with two different granule sizes, were tested. Three corrosive solutions with different pH and simulated body fluid (SBF were used for immersing of the samples. Changes in concentrations of calcium and phosphate ions, pH level and weight changes of the samples were observed. It was found that presence of TRIS buffer enhanced dissolution rate of the β-TCP approximately two times. When exposed to SBF solution, calcium phosphate (most probably hydroxyapatite precipitation predominates over β-TCP dissolution. Results from HAp samples dissolution showed some unexpected findings. Neither heat treatment nor HAp particle size made any major differences in dissolution rate of the same mass of each HAp sample.

  8. Effect of different retarders on the hydration of calcium sulfoaluminate eco-cement pastes

    OpenAIRE

    García-Maté, Marta; De la Torre, Ángeles G.; Aranda, Miguel A. G.; Santacruz, Isabel

    2014-01-01

    The manufacture of Calcium SulfoAluminate (CSA) cements is more environmentally friendly than that of OPC [1] as their production releases up to 40% less CO2 than the latter. The main performances of CSA cements are fast setting time, good-chemical resistance properties and high early strengths. CSA cements are prepared by mixing CSA clinker with different amounts of a calcium sulfate set regulator such as gypsum (CaSO4•2H2O), bassanite (CaSO4•½H2O), or anhydrite (CaSO4), or mixtures of th...

  9. Selective laser sintering of calcium phosphate materials for orthopedic implants

    Science.gov (United States)

    Lee, Goonhee

    Two technologies, Solid Freeform Fabrication (SFF) and bioceramics are combined in this work to prepare bone replacement implants with complex geometry. SFF has emerged as a crucial technique for rapid prototyping in the last decade. Selective Laser Sintering (SLS) is one of the established SFF manufacturing processes that can build three-dimensional objects directly from computer models without part-specific tooling or human intervention. Meanwhile, there have been great efforts to develop implantable materials that can assist in regeneration of bone defects and injuries. However, little attention has been focused in shaping bones from these materials. The main thrust of this research was to develop a process that can combine those two separate efforts. The specific objective of this research is to develop a process that can construct bone replacement material of complex geometry from synthetic calcium phosphate materials by using the SLS process. The achievement of this goal can have a significant impact on the quality of health care in the sense that complete custom-fit bone and tooth structures suitable for implantation can be prepared within 24--48 hours of receipt of geometric information obtained either from patient Computed Tomographic (CT) data, from Computer Aided Design (CAD) software or from other imaging systems such as Magnetic Resonance Imaging (MRI) and Holographic Laser Range Imaging (HLRI). In this research, two different processes have been developed. First is the SLS fabrication of porous bone implants. In this effort, systematic procedures have been established and calcium phosphate implants were successfully fabricated from various sources of geometric information. These efforts include material selection and preparation, SLS process parameter optimization, and development of post-processing techniques within the 48-hour time frame. Post-processing allows accurate control of geometry and of the chemistry of calcium phosphate, as well as

  10. Europium-doped amorphous calcium phosphate porous nanospheres: preparation and application as luminescent drug carriers

    OpenAIRE

    Zhang Kui-Hua; Mo Xiu-Mei; Chen Feng; Zhu Ying-Jie; Wu Jin; Wang Ke-Wei; Tang Qi-Li

    2011-01-01

    Abstract Calcium phosphate is the most important inorganic constituent of biological tissues, and synthetic calcium phosphate has been widely used as biomaterials. In this study, a facile method has been developed for the fabrication of amorphous calcium phosphate (ACP)/polylactide-block-monomethoxy(polyethyleneglycol) hybrid nanoparticles and ACP porous nanospheres. Europium-doping is performed to enable photoluminescence (PL) function of ACP porous nanospheres. A high specific surface area ...

  11. The Transformation of Calcium Phosphate Bioceramics in Vivo

    Institute of Scientific and Technical Information of China (English)

    DAI Hong-lian; CAO Xian-ying; LI Xiao-xi; YAN Yu-hua; LI Shi-pu

    2003-01-01

    To study the transformation process of calcium phosphate bioceramic in vivo,biodegradable porous β-tricalcium phosphate ceramics (β-TCP) were used in this experiment. The materials (φ5×8mm) were implanted in the tibia of rabbits. The β-TCP ceramics with bone tissue were retrieved and treated for histology, and then observed by using a scanning electron microscope (SEM) and an electron probe X-ray microanalyzer (EMPA) every month. The results show that β-TCP ceramics bond to bone directly,new bones are forming and maturing with materials continuous degrading,and the materials are nearly replaced by the formed bone finally.Parts of the materials were degraded,absorpted and recrystallized,the others dispersped on the cancellous bone and the Haversian lamella with an irregular arrangement incorporating in bone formation directly by remodeling structure.

  12. Bioactivity of calcium phosphate bioceramic coating fabricated by laser cladding

    Science.gov (United States)

    Zhu, Yizhi; Liu, Qibin; Xu, Peng; Li, Long; Jiang, Haibing; Bai, Yang

    2016-05-01

    There were always strong expectations for suitable biomaterials used for bone regeneration. In this study, to improve the biocompatiblity of titanium alloy, calcium phosphate bioceramic coating was obtained by laser cladding technology. The microstructure, phases, bioactivity, cell differentiation, morphology and resorption lacunae were investigated by optical microscope (OM), x-ray diffraction (XRD), methyl thiazolyl tetrazolium (MTT) assay, tartrate-resistant acid phosphatase (TRAP) staining and scanning electronic microscope (SEM), respectively. The results show that bioceramic coating consists of three layers, which are a substrate, an alloyed layer and a ceramic layer. Bioactive phases of β-tricalcium phosphate (β-TCP) and hydroxyapatite (HA) were found in ceramic coating. Osteoclast precursors have excellent proliferation on the bioceramic surface. The bioceramics coating could be digested by osteoclasts, which led to the resorption lacunae formed on its surface. It revealed that the gradient bioceramic coating has an excellent bioactivity.

  13. Interactions of casein micelles with calcium phosphate particles.

    Science.gov (United States)

    Tercinier, Lucile; Ye, Aiqian; Anema, Skelte G; Singh, Anne; Singh, Harjinder

    2014-06-25

    Insoluble calcium phosphate particles, such as hydroxyapatite (HA), are often used in calcium-fortified milks as they are considered to be chemically unreactive. However, this study showed that there was an interaction between the casein micelles in milk and HA particles. The caseins in milk were shown to bind to the HA particles, with the relative proportions of bound β-casein, αS-casein, and κ-casein different from the proportions of the individual caseins present in milk. Transmission electron microscopy showed no evidence of intact casein micelles on the surface of the HA particles, which suggested that the casein micelles dissociated either before or during binding. The HA particles behaved as ion chelators, with the ability to bind the ions contained in the milk serum phase. Consequently, the depletion of the serum minerals disrupted the milk mineral equilibrium, resulting in dissociation of the casein micelles in milk. PMID:24896851

  14. Preparation of magnesium phosphate cement by recycling the product of thermal transformation of asbestos containing wastes

    OpenAIRE

    Viani, A; Gualtieri, A.F.

    2014-01-01

    Asbestos containing wastes have been employed for the first time in the formulation of magnesium phosphate cements. Two samples were mixed with magnesium carbonate and calcined at 1100 and 1300 C. Under these conditions, complete destruction of asbestos minerals is known to occur. The product, containing MgO, after reaction with water-soluble potassium di-hydrogen phosphate, led to the formation of hydrated phases at room temperature. Crystalline and amorphous reaction products were detected,...

  15. Macrophage and osteoblast responses to biphasic calcium phosphate microparticles.

    Science.gov (United States)

    Fellah, Borhane Hakim; Delorme, Bruno; Sohier, Jérôme; Magne, David; Hardouin, Pierre; Layrolle, Pierre

    2010-06-15

    The aim of this work was to investigate in vitro the biological events leading to ectopic bone formation in contact with microporous biphasic calcium phosphate (BCP) ceramics. After implantation, microparticles may arise from their degradation and induce an inflammatory response involving macrophages. The secretion of pro-inflammatory cytokines may affect the differentiation of osteoblasts. Mouse macrophage-like (J774) and osteoblast-like (MC3T3-E1) cells were cultured in the presence of BCP microparticles of different sizes (response initiated by BCP microparticles may have both detrimental and beneficial effects on osteogenesis. PMID:20014296

  16. Mesoscale crystallization of calcium phosphate nanostructures in protein (casein) micelles

    Science.gov (United States)

    Thachepan, Surachai; Li, Mei; Mann, Stephen

    2010-11-01

    Aqueous micelles of the multi-protein calcium phosphate complex, casein, were treated at 60 °C and pH 7 over several months. Although partial dissociation of the micelles into 12 nm sized amorphous calcium phosphate (ACP)/protein nanoparticles occurred within a period of 14 days, crystallization of the ACP nanoclusters into bundles of hydroxyapatite (HAP) nanofilaments was not observed until after 12 weeks. The HAP nanofilaments were formed specifically within the partially disrupted protein micelles suggesting a micelle-mediated pathway of mesoscale crystallization. Similar experiments using ACP-containing synthetic micelles prepared from β-casein protein alone indicated that co-aligned bundles of HAP nanofilaments were produced within the protein micelle interior after 24 hours at temperatures as low as 35 °C. The presence of Mg2+ ions in the casein micelles, as well as a possible synergistic effect associated with the multi-protein nature of the native aggregates, could account for the marked inhibition in mesoscale crystallization observed in the casein micelles compared with the single-component β-casein constructs.Aqueous micelles of the multi-protein calcium phosphate complex, casein, were treated at 60 °C and pH 7 over several months. Although partial dissociation of the micelles into 12 nm sized amorphous calcium phosphate (ACP)/protein nanoparticles occurred within a period of 14 days, crystallization of the ACP nanoclusters into bundles of hydroxyapatite (HAP) nanofilaments was not observed until after 12 weeks. The HAP nanofilaments were formed specifically within the partially disrupted protein micelles suggesting a micelle-mediated pathway of mesoscale crystallization. Similar experiments using ACP-containing synthetic micelles prepared from β-casein protein alone indicated that co-aligned bundles of HAP nanofilaments were produced within the protein micelle interior after 24 hours at temperatures as low as 35 °C. The presence of Mg2+ ions in

  17. Physicochemical characterization of zinc-substituted calcium phosphates

    Indian Academy of Sciences (India)

    DOROTA WALCZYK; DAGMARA MALINA; MILENA KRÓL; KLAUDIA PLUTA; AGNIESZKA SOBCZAK-KUPIEC

    2016-04-01

    Biocompatible and bioactive calcium phosphates can make chemical bonds with living bones. Improvement of their biological and physicochemical properties can be achieved by doping with various ions that are presented in natural apatites of bones. These substitutions influence lattice parameters, structure and morphology of apatites. In recent times great attention has been devoted to zinc ions that are the second most abundant trace element present in bones. Zinc embedded into calcium phosphate may enhance the bone formation and in addition exhibits antifungal and antibacterial properties. Therefore, it is rational to form structures incorporated with this ion. In this paper the incorporation of the Zn ions into natural and synthetic calcium phosphates has been reported.Natural hydroxyapatites (HAs) applied in this study were derived mainly from pork bones whereas both brushite and synthetic were formed using wet chemical methods. Ambient temperature synthesis leads to the formation ofbrushite, whereas the process performed at elevated temperature gives HA. Subsequently, attained structures were modified with Zn ions by using in situ or sorption procedures. Phase composition and morphology of obtained materials were determined by means of X-ray diffractometry, Fourier transform infrared spectroscopy and scanning electron microscopy equipped with energy-dispersive spectroscopy. Introduced XRD patterns depict changes of the crystallinity of HA with the increase in the amount of embedded zinc ions. On the contrary, no changes of the crystallinity were observed for the brushite doped with Zn ions. Morphology of attained powders, visualized using scanningelectron microscopy exemplified structural changes between calcium phosphates conjugated with zinc ions. Many authors report that the addition of small amounts of Zn ions leads to loss of crystallinity and decrease of lattice parameters. Interestingly, upon addition of Zn ions to the natural and synthetic HAp by sorption

  18. Poly(ethylene imine)-controlled Calcium Phosphate mineralization

    OpenAIRE

    Shkilnyy, Andriy; Friedrich, Alwin; Tiersch, Brigitte; Schöne, Stefanie; Fechner, Mabya; Koetz, Joachim; Schläpfer, Carl-Wilhelm; Taubert, Andreas

    2008-01-01

    The current paper shows that poly(ethylene imine) (PEI) is an efficient template for the fabrication of spherical calcium phosphate (CaP)/polymer hybrid particles at pH values above 8. The polymer forms spherical entities, which contain one or a few CaP particles with diameters of ca. 6 nm. The samples contain up to 20 wt % polymer, which appears to be wrapped around the small CaP particles. The particles form via a mineralization-trapping pathway, where at the beginning of the precipitation ...

  19. Effects of protein incorporation on calcium phosphate coating

    OpenAIRE

    Leonor, I. B.; C.M. Alves; Azevedo, Helena S.; Reis, R.L.

    2009-01-01

    The incorporation of proteins into calcium phosphate (Ca–P) coatings is expected to alter their properties. The aim of this work is, therefore, to study the effect of protein concentration on the formation of Ca–P film. A biodegradable blend of corn starch/ethylene vinyl alcohol (SEVA-C) was used as substrate and bioactive glass (45S5 Bioglass®) was used as a nucleating agent. Bovine serum albumin (BSA) and α-amylase were added, separately, at a concentration of 0.5, 1, and 5 mg/mLto simulate...

  20. Post cementation sensitivity evaluation of glass Ionomer, zinc phosphate and resin modified glass Ionomer luting cements under class II inlays: An in vivo comparative study

    Directory of Open Access Journals (Sweden)

    Chandrasekhar V

    2010-01-01

    Full Text Available Objective: This study aims to compare the patient-perceived post-cementation sensitivity of class II metal restorations preoperatively, immediately after cementation, one week after cementation and one month after cementation with (1 Glass Ionomer luting cement (2 Zinc Phosphate cement and (3 Resin-modified Glass Ionomer luting cement. Materials and Methods: A total of 60 patients, irrespective of sex, in the age group of 15-50 years were selected and the teeth were randomly divided into three groups of 20 each. Twenty inlay cast restorations were cemented with three different luting cements. The criteria adapted to measure tooth sensitivity in the present study were objective examination for sensitivity.(1 Cold water test (2 Compressed air test and (3 Biting pressure test. Results: The patients with restorations cemented with Resin-modified Glass ionomer demonstrated the least postoperative sensitivity when compared with Glass Ionomer and zinc phosphate cement at all different intervals of time evaluated by different tests. Conclusion: The patients with restorations cemented with resin-modified Glass ionomer demonstrated the least postoperative sensitivity.

  1. A new evaporation-based method for the preparation of biomimetic calcium phosphate coatings on metals

    International Nuclear Information System (INIS)

    This study reports a new method to prepare biomimetic calcium phosphate coatings on titanium, stainless steel, CoCrMo, and tantalum. The method does not require surface etching, high supersaturation, or tight control of solution conditions. Metallic samples were dipped into a supersaturated calcium phosphate solution, withdrawn, and left to dry at room temperature. Calcium phosphate crystallites formed on and completely covered the surfaces by repeating the dip-and-dry treatment. The crystallite-covered surfaces readily grew to calcium phosphate coatings when immersed in the supersaturated solution. The mechanism of the treatment was suggested to be an evaporation-induced surface crystallization process.

  2. Physical characteristics, antimicrobial and odontogenesis potentials of calcium silicate cement containing hinokitiol.

    Science.gov (United States)

    Huang, Ming-Hsien; Shen, Yu-Fang; Hsu, Tuan-Ti; Huang, Tsui-Hsien; Shie, Ming-You

    2016-08-01

    Hinokitiol is a natural material and it has antibacterial and anti-inflammatory effects. The purpose of this study was to evaluate the material characterization, cell viability, antibacterial and anti-inflammatory abilities of the hinokitiol-modified calcium silicate (CS) cement as a root end filling material. The setting times, diametral tensile strength (DTS) values and XRD patterns of CS cements with 0-10mM hinokitiol were examined. Then, the antibacterial effect and the expression levels of cyclooxygenase 2 (COX-2) and interleukin-1 (IL-1) of the hinokitiol-modified CS cements were evaluated. Furthermore, the cytocompatibility, the expression levels of the markers of odontoblastic differentiation, mineralized nodule formation and calcium deposition of human dental pulp cells (hDPCs) cultured on hinokitiol-modified CS cements were determined. The hinokitiol-modified CS cements had better antibacterial and anti-inflammatory abilities and cytocompatibility than non-modified CS cements. Otherwise, the hinokitiol-modified CS cements had suitable setting times and better odontoblastic potential of hDPCs. Previous report pointed out that the root-end filling materials may induce inflammatory cytokines reaction. In our study, hinokitiol-modified CS cements not only inhibited the expression level of inflammatory cytokines, but also had better cytocompatibility, antimicrobial properties and active ability of odontoblastic differentiation of hDPCs. Therefore, the hinokitiol-modified CS cement may be a potential root end filling material for clinic. PMID:27157721

  3. Mg-phosphate ceramics produced from the product of thermal transformation of cement-asbestos

    Czech Academy of Sciences Publication Activity Database

    Pérez-Estébanez, Marta; Mácová, Petra; Šašek, Petr; Viani, Alberto; Gualtieri, A.

    2014-01-01

    Roč. 34, č. 2 (2014), s. 187-192. ISSN 1640-4920. [Conference on Environment and Mineral Processing /18./. Ostrava, 29.05.2014-31.05.2014] R&D Projects: GA MŠk(CZ) LO1219 Keywords : cement-asbestos * magnesium phosphate ceramics * amorphous Subject RIV: AL - Art, Architecture, Cultural Heritage http://www.potopk.com.pl/archiwum.html

  4. Characterization of modified calcium-silicate cements exposed to acidic environment

    Energy Technology Data Exchange (ETDEWEB)

    Camilleri, Josette, E-mail: josette.camilleri@um.edu.mt

    2011-01-15

    Portland cement which is used as a binder in concrete in the construction industry has been developed into a biomaterial. It is marketed as mineral trioxide aggregate and is used in dentistry. This material has been reported to be very biocompatible and thus its use has diversified. The extended use of this material has led to developments of newer versions with improved physical properties. The aim of this study was to evaluate the effect of acidic environments found in the oral cavity on fast setting calcium silicate cements with improved physical properties using a combination of techniques. Two fast setting calcium silicate cements (CSA and CFA) and two cement composites (CSAG and CFAG) were assessed by subjecting the materials to lactic acid/sodium lactate buffer gel for a period of 28 days. At weekly intervals the materials were viewed under the tandem scanning confocal microscope (TSM), and scanning electron microscope (SEM). The two prototype cements exhibited changes in their internal chemistry with no changes in surface characteristics. Since the changes observed were mostly sub-surface evaluation of surface characteristics of cement may not be sufficient in the determination of chemical changes occurring. - Research Highlights: {yields} An acidic environment affects modified fast setting calcium silicate-based cements. {yields} No surface changes are observed in acidic environment. {yields} An acidic environment causes sub-surface changes in the material chemistry which are only visible in fractured specimens. {yields} A combination of techniques is necessary in order to evaluate the chemical changes occurring.

  5. Characterization of modified calcium-silicate cements exposed to acidic environment

    International Nuclear Information System (INIS)

    Portland cement which is used as a binder in concrete in the construction industry has been developed into a biomaterial. It is marketed as mineral trioxide aggregate and is used in dentistry. This material has been reported to be very biocompatible and thus its use has diversified. The extended use of this material has led to developments of newer versions with improved physical properties. The aim of this study was to evaluate the effect of acidic environments found in the oral cavity on fast setting calcium silicate cements with improved physical properties using a combination of techniques. Two fast setting calcium silicate cements (CSA and CFA) and two cement composites (CSAG and CFAG) were assessed by subjecting the materials to lactic acid/sodium lactate buffer gel for a period of 28 days. At weekly intervals the materials were viewed under the tandem scanning confocal microscope (TSM), and scanning electron microscope (SEM). The two prototype cements exhibited changes in their internal chemistry with no changes in surface characteristics. Since the changes observed were mostly sub-surface evaluation of surface characteristics of cement may not be sufficient in the determination of chemical changes occurring. - Research Highlights: → An acidic environment affects modified fast setting calcium silicate-based cements. → No surface changes are observed in acidic environment. → An acidic environment causes sub-surface changes in the material chemistry which are only visible in fractured specimens. → A combination of techniques is necessary in order to evaluate the chemical changes occurring.

  6. Post cementation sensitivity evaluation of glass Ionomer, zinc phosphate and resin modified glass Ionomer luting cements under class II inlays: An in vivo comparative study

    OpenAIRE

    Chandrasekhar V

    2010-01-01

    Objective: This study aims to compare the patient-perceived post-cementation sensitivity of class II metal restorations preoperatively, immediately after cementation, one week after cementation and one month after cementation with (1) Glass Ionomer luting cement (2) Zinc Phosphate cement and (3) Resin-modified Glass Ionomer luting cement. Materials and Methods: A total of 60 patients, irrespective of sex, in the age group of 15-50 years were selected and the teeth were randomly divided int...

  7. Effect of calcium triphosphate cement on proximal humeral fracture osteosynthesis: a finite element analysis.

    Science.gov (United States)

    Kennedy, Jim; Feerick, Emer; McGarry, Patrick; FitzPatrick, David; Mullett, Hannan

    2013-08-01

    PURPOSE. To measure the effect of void-filling calcium triphosphate cement on the loads at the implant-bone interface of a proximal humeral fracture osteosynthesis using a finite element analysis. METHODS. Finite element models of a 3-part proximal humeral fracture fixed with a plate with and without calcium triphosphate cement augmentation were generated from a quantitative computed tomography dataset of an intact proximal humerus. Material properties were assigned to bone fragments using published expressions relating Young's modulus to local Hounsfield number. Boundary conditions were then applied to the model to replicate the physiological loads. The effect of void-filling calcium triphosphate cement was analysed. RESULTS. When the void was filled with calcium triphosphate cement, the pressure gradient of the bone surrounding the screws in the medial fracture fragment decreased 97% from up to 21.41 to 0.66 MPa. Peak pressure of the fracture planes decreased 95% from 6.10 to 0.30 MPa and occurred along the medial aspect. The mean stress in the screw locking mechanisms decreased 78% from 71.23 to 15.92 MPa. The angled proximal metaphyseal screw had the highest stress. CONCLUSION. Augmentation with calcium triphosphate cement improves initial stability and reduces stress on the implant-bone interface. PMID:24014777

  8. Study of belite calcium sulfo-aluminate cement potential for zinc conditioning: From hydration to durability

    International Nuclear Information System (INIS)

    Calcium silicate cements are widely used for low- and intermediate-level radioactive waste conditioning. However, wastes produced by nuclear activities are very diverse and some of their components may chemically react with cement phases. For instance, ashes resulting from the incineration of technological wastes including neoprene and polyvinylchloride may contain substantial amounts of soluble zinc chloride. This compound is known to strongly delay or inhibit Portland cement setting. One approach to limit adverse cement-waste interactions is to select a binder showing a better compatibility with the waste while keeping cement matrix advantages (low cost, simple process, hydration with water provided by the waste...). This work thus investigates the potential of calcium sulfo-aluminate cement for zinc Zn(II) immobilization. Four aspects were considered: hydration (kinetics and products formed), properties of hydrated binders, mechanisms of zinc retention and durability of the cement pastes (based on leaching experiments and modelling). The influence of three main parameters was assessed: the gypsum content of the cement, the concentration of ZnCl2 and the thermal evolution at early age. It follows that materials based on a calcium sulfo-aluminate cement containing 20% gypsum are interesting candidates for zinc Zn(II) stabilization/solidification: there is no delay in hydration, mineralogy of the hydrated phases is slightly dependent on thermal history, mechanical strength is high, dimensional changes are limited and zinc Zn(II) is well immobilized, even if the cement paste is leached by pure water during a long period (90 d). (author)

  9. Structure and properties of gadolinium loaded calcium phosphate glasses

    International Nuclear Information System (INIS)

    The glass samples with composition xGd2O3–(50 − x)CaO–50P2O5 (0 ⩽ x ⩽ 9 mol%) were prepared by the conventional melt quench method. The structure and properties of gadolinium loaded in calcium phosphate glasses were investigated using XRD, SEM, DTA, IR and Raman spectroscopy. The XRD and SEM analysis for the samples show that the majority of samples are amorphous, and crystallization occurs when the content of Gd2O3 containing is up to 6 mol%. Two main crystalline phases, Ca2P2O7 and Gd3(P2O7)3, are embedded in an amorphous matrix. IR and Raman data indicate that glass structure consists of predominantly metaphosphate (Q2) units and the depolymerization of phosphate network with the addition of Gd2O3. Both the chemical durability and the glass transition temperature (Tg) are improved with the increase of Gd2O3, which suggests that the Gd acts a role of strengthening the cross-links between the phosphate chains of the glass

  10. The increasing of enamel calcium level after casein phosphopeptideamorphous calcium phosphate covering

    Directory of Open Access Journals (Sweden)

    Widyasri Prananingrum

    2012-06-01

    Full Text Available Background: Caries process is characterized by the presence of demineralization. Demineralization is caused by organic acids as a result of carbohydrate substrate fermentation. Remineralization is a natural repair process for non-cavitated lesions. Remineralization occurs if there are Ca2+ and PO43- ions in sufficient quantities. Casein-amorphous calcium phosphate phosphopeptide (CPP-ACP is a paste material containing milk protein (casein, that actually contains minerals, such as calcium and phosphate. The casein ability to stabilize calcium phosphate and enhance mineral solubility and bioavailability confers upon CPP potential to be biological delivery vehicles for calcium and phosphate. Purpose: The aim of this study was to determine the calcium levels in tooth enamel after being covered with CPP-ACP 2 times a day for 3, 14 and 28 days. Methods: Sample were bovine incisors of 3 year old cows divided into 4 groups, namely group I as control group, group II, III and IV as treatment groups covered with CPP-ACP 2 times a day. All of those teeth were then immersed in artificial saliva. Group II was immersed for 3 days, while group III was immersed for 14 days, and group IV was immersed for 28 days. One drop of CPP-ACP was used to cover the entire labial surface of teeth. The measurement of the calcium levels was then conducted by using titration method. All data were analyzed by One- Way ANOVA test with 5% degree of confidence. Results: The results showed significant difference of the calcium levels in tooth enamel of those groups after covered with CPP-ACP 2 times a day for 3, 14 and 28 days (p = 0.001. There is also significant difference of the calcium levels in tooth enamel of those treatment groups and the control group (p = 0.001. Conclusion: The calcium levels of tooth enamel are increased after covered with CPP-ACP 2 times a day for 3, 14 and 28 days.Latar belakang: Proses terjadinya karies gigi ditandai oleh adanya demineralisasi

  11. Mechanical Behavior and Thermal Stability of Acid-Base Phosphate Cements and Composites Fabricated at Ambient Temperature

    Science.gov (United States)

    Colorado Lopera, Henry Alonso

    This dissertation presents the study of the mechanical behavior and thermal stability of acid-base phosphate cements (PCs) and composites fabricated at ambient temperature. These materials are also known as chemically bonded phosphate ceramics (CBPCs). Among other advantages of using PCs when compared with traditional cements are the better mechanical properties (compressive and flexural strength), lower density, ultra-fast (controllable) setting time, controllable pH, and an environmentally benign process. Several PCs based on wollastonite and calcium and alumino phosphates after thermal exposure up to 1000°C have been investigated. First, the thermo-mechanical and chemical stability of wollastonite-based PC (Wo-PC) exposed to temperatures up to 1000°C in air environment were studied. The effects of processing conditions on the curing and shrinkage of the wollastonite-based PC were studied. The chemical reactions and phase transformations during the fabrication and during the thermal exposure are analyzed in detail using scanning electron microscopy (SEM), X-ray diffraction (XRD), and thermo-gravimetric analysis (TGA Then, the thermo-mechanical and chemical stability of glass, carbon and basalt fiber reinforced Wo-PC composites, were studied using SEM, XRD, TGA. The flexural strength and Weibull statistics were analyzed. A significant strength degradation in the composites were found after the thermal exposure at elevated temperatures due to the interdifusion and chemical reactions across the fibers and the matrix at temperatures over 600°C. To overcome this barrier, we have developed a new PC based on calcium and alumino-phosphates (Ca-Al PCs). The Ca-Al PCs were studied in detail using SEM, XRD, TGA, curing, shrinkage, Weibull statistics, and compression tests. Our study has confirmed that this new composite material is chemically and mechanically stable at temperatures up to 1000°C. Moreover, the compression strength increases after exposure to 1000

  12. Leaching of nuclear waste glass in cement pore water: effect of calcium in solution

    International Nuclear Information System (INIS)

    In the French geological repository concept, intermediate-level vitrified wastes could be disposed of in a cement medium. The glass dissolution mechanisms and kinetics, expected to depend strongly on the chemical composition and pH of the leaching water, were studied in various cement pore water compositions corresponding to different stages of cement aging. In this study, we focused on the effects induced by cement pore water at equilibrium with respect to Portlandite (pH[25 C] = 12.4). A decrease in the maximum glass dissolution rate due to the effect of calcium was clearly observed compared to the reference medium, i.e. at the same pH in KOH solution. At higher reaction progress, calcium in solution was almost totally consumed after a few days, probably due to the formation of Calcium Silicate Hydrate (C-S-H) phases with silicon leached from the glass. Two assumptions can be proposed to explain the effect of calcium on the initial regime: either the calcium from solution reacts with silicon released to form a C-S-H passivating layer at the glass/solution interface, or calcium compensates two non-bridging oxygen (Si-O-) in the altered layer, which could decrease the hydrolysis of silicon bonds. (authors)

  13. Effect of Fluoride, Casein Phosphopeptide–Amorphous Calcium Phosphate and Casein Phosphopeptide–Amorphous Calcium Phosphate Fluoride on Enamel Surface Microhardness After Microabrasion: An In Vitro Study

    OpenAIRE

    Ghazaleh Ahmadi Zenouz; Fariba Ezoji; Seyede Anese Enderami; Soraya Khafri

    2016-01-01

    Objectives: This study aimed to assess the effect of applying casein phosphopeptide–amorphous calcium phosphate (CPP-ACP) paste, casein phosphopeptide–amorphous calcium phosphate fluoride (CPP-ACPF) paste and sodium fluoride gel on surface microhardness of enamel after microabrasion.Materials and Methods: Thirty freshly extracted human premolars were selected. All samples were subjected to hardness indentations made with the Vickers hardness machine and the average value was recorded as the i...

  14. The flame photometric determination of calcium in phosphate, carbonate, and silicate rocks

    Science.gov (United States)

    Kramer, H.

    1957-01-01

    A flame photometric method of determining calcium in phosphate, carbonate, and silicate locks has been developed Aluminum and phosphate interference was overcome by the addition of a large excess of magnesium. The method is rapid and suitable for routine analysis Results obtained are within ?? 2% of the calcium oxide content. ?? 1957.

  15. Calcium aluminate cements for nuclear wastes conditioning: literature review and new approaches

    International Nuclear Information System (INIS)

    Encapsulate the diverse wastes produced by nuclear activities in cementitious binders may be very complex due to the adverse cement-waste interactions. Consequences are for example: strong delay, poor mechanical strength or low resistance to leaching. In this case, pure or blended calcium aluminate cements (CACs) may be valuable alternatives. This paper summarises the properties of CAC and blended CAC system and gives some examples from literature where calcium aluminate cements are used for conventional wastes or nuclear wastes conditioning. Moreover, it proposes another approach: using CAC not only as a binder, but also as a chemical reactant. After dissolution calcium aluminates ions can combine with many chemical species (sulphates, nitrates, chlorides, alkali metals, heavy metals) to precipitate specific hydrates allowing chemical trapping of these species. An example is given for the purification of Ni and Zn nitrates solutions. (authors)

  16. Properties of Chemically Combusted Calcium Carbide Residue and Its Influence on Cement Properties

    OpenAIRE

    Hongfang Sun; Zishanshan Li; Jing Bai; Shazim Ali Memon; Biqin Dong; Yuan Fang; Weiting Xu; Feng Xing

    2015-01-01

    Calcium carbide residue (CCR) is a waste by-product from acetylene gas production. The main component of CCR is Ca(OH)2, which can react with siliceous materials through pozzolanic reactions, resulting in a product similar to those obtained from the cement hydration process. Thus, it is possible to use CCR as a substitute for Portland cement in concrete. In this research, we synthesized CCR and silica fume through a chemical combustion technique to produce a new reactive cementitious powder (...

  17. Investigation of fresh and hardened properties of Calcium sulfoaluminate (CSA) cement blends

    OpenAIRE

    Herrmann, P

    2014-01-01

    Calcium sulfoaluminate (CSA) is a comparatively new cementitious material that is mainly established in China where it is produced in a large scale. CSA cement is not covered by European standards. However, it provides different beneficial properties such as rapid hardening and high early strength development. Furthermore, the usage of CSA cement can save energy during production process in comparison to established cementitious materials. Therefore it is also more environmental friendly. ...

  18. Corrosion Resistance of Calcium Aluminate Cement Concrete Exposed to a Chloride Environment

    OpenAIRE

    Ki Yong Ann; Chang-Geun Cho

    2014-01-01

    The present study concerns a development of calcium aluminate cement (CAC) concrete to enhance the durability against an externally chemically aggressive environment, in particular, chloride-induced corrosion. To evaluate the inhibition effect and concrete properties, CAC was partially mixed with ordinary Portland cement (OPC), ranging from 5% to 15%, as a binder. As a result, it was found that an increase in the CAC in binder resulted in a dramatic decrease in the setting time of fresh concr...

  19. (α'(H))-Dicalcium silicate bone cement doped with tricalcium phosphate: characterization, bioactivity and biocompatibility.

    Science.gov (United States)

    de Aza, Piedad N; Zuleta, Fausto; Velasquez, Pablo; Vicente-Salar, Nestor; Reig, Juan A

    2014-02-01

    The influence of phosphorus doping on the properties of (α'(H))-dicalcium silicate (C(2)S) bone cement was analyzed, in addition to bioactivity and biocompatibility. All the cements were composed of a solid solution of TCP in C(2)S ([Formula: see text]-C(2)S(ss)) as the only phase present. The compressive strength ranged from 3.8-16.3 MPa. Final setting times ranged from 10 to 50 min and were lower for cements with lower L/P content. Calcium silicate hydrate was the principal phase formed during the hydration process of the cements. The cement exhibited a moderate degradation and could induce carbonated hydroxyapatite formation on its surface and into the pores. The cell attachment test showed that the (α'(H))-C(2)SiO(4) solid solution supported human adipose stem cells adhesion and spreading, and the cells established close contacts with the cement after 24 h of culture. The novel (α'(H))-C(2)S(ss) cements might be suitable for potential applications in the biomedical field, preferentially as materials for bone/dental repair. PMID:24218299

  20. Device for continuous radiometric determination of the calcium and iron content in raw slurry for cement

    International Nuclear Information System (INIS)

    The characteristic iron and calcium-K series were excited using a Cd-109 isotope source. In order to determine the calcium and iron content in dry slurry, the Compton-effect scattered radiation of the Cd-109 source in the sample was used. A numerical process was worked out which allowed the elimination of the influence of changing contents of iron and water on the results of the calcium content determinations, and a device for continuous radiometric determination of calcium and iron in raw slurry was designed and constructed. The device was installed in the cement plant 'Przyjazn' under technical measuring conditions and its applicability was tested. (orig./LH)

  1. CALCIUM ORTHOPHOSPHATES HYDRATES: FORMATION, STABILITY AND INFLUENCE ON STANDARD PROPERTIES OF PORTLAND CEMENT

    Directory of Open Access Journals (Sweden)

    Kaziliunas A.

    2013-12-01

    Full Text Available Preparation of phosphogypsum to produce the binders requires a much higher input than preparation of natural gypsum stone. This makes it uncompetitive material. The investigations presented therein are meant to reduce this input by looking for the ways of rendering impurities harmless. Soluble acid orthophosphates are the main harmful impurity of phosphogypsum. The studies show that dry insoluble calcium orthophosphates hydrates (1.09 % and 2.18 % P2O5 in gypsum have little effect on W/C, setting times and soundness of Portland cement pastes. Insoluble calcium orthophosphates hydrates {CaHPO4∙2H2O, Ca8(HPO42(PO44∙5H2O and Ca9(HPO4(PO45(OH∙4H2O} formed in acidic medium (pH = 4.2 - 5.9 have been destroyed in alkaline medium and reduce standard compressive strength of cement up to 28 %. Calcium orthophosphates hydrates of hydroxyapatite group are stable in alcaline medium, while in dry state they reduce the standard compressive strength of cement until 10 %, but their suspensions prolong setting times of Portland cement as soluble orthophosphates – 2 - 3 times. Alkalis in cement increase pH of paste, but do not change the process of formation of calcium orthophosphates hydrates of hydroxyapatite group: it takes place through an intermediate phase - CaHPO4·2H2O, whose transformation into apatite lasts for 2 - 3 months.

  2. Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone

    DEFF Research Database (Denmark)

    Moesgaard, M; Poulsen, Søren Lundsted; Herfort, D; Steenberg, M; Kirkegaard, L F; Skibsted, Jørgen; Yue, Y

    2012-01-01

    M. MOESGAARD, S.L. POULSEN, D. HERFORT, M. STEENBERG, L.F. KIRKEGAARD, J. SKIBSTED, Y. YUE, Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone, Journal of the American Ceramic Society 95, 403 – 409 (2012).......M. MOESGAARD, S.L. POULSEN, D. HERFORT, M. STEENBERG, L.F. KIRKEGAARD, J. SKIBSTED, Y. YUE, Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone, Journal of the American Ceramic Society 95, 403 – 409 (2012)....

  3. Coating of calcium phosphate on biometallic materials by electrophoretic deposition

    Institute of Scientific and Technical Information of China (English)

    ZHANG Er-lin; YANG Ke

    2005-01-01

    Although biometallic materials have been used as bone implant materials for a long time, they are still detected as foreign bodies by human immune system. Calcium phosphate coating, especially hydroxyapatite(HA)coating attracts special attention due to its good biocompatibility. Being one of the effective methods used to deposit HA coating onto the metallic implant, the electrophoretic deposition(EPD) was reviewed in detail, including the process of EPD, the advantages and disadvantages, the important processing factors and the microstructure and mechanical properties of the coating. Research results on the processing and the coating show potential application of EPD process to the biomedical materials surface modification. In addition, the nanoparticulate HA coating as a new trend in HA coating was also introduced.

  4. Push-out bond strength of MTA HP, a new high-plasticity calcium silicate-based cement.

    Science.gov (United States)

    Silva, Emmanuel Jnl; Carvalho, Nancy Kudsi; Zanon, Mayara; Senna, Plínio Mendes; DE-Deus, Gustavo; Zuolo, Mário Luis; Zaia, Alexandre Augusto

    2016-06-14

    This study was designed to investigate the resistance to dislodgment provided by MTA HP, a new high-plasticity calcium silicate-based cement. Biodentine and White MTA Angelus were used as reference materials for comparison. Three discs 1 ± 0.1 mm thick were obtained from the middle third of the roots of 5 maxillary canines. Three 0.8-mm-wide holes were drilled on the axial surface of each root disc. Standardized irrigation was performed. Then the holes were dried with paper points and filled with one of the three tested cements. The filled dental slices were immersed in a phosphate-buffered saline (PBS) solution (pH 7.2) for 7 days before the push-out assessment. The Kruskal-Wallis test was applied to assess the effect of each endodontic cement on the push-out bond strength. Mann-Whitney with Bonferroni correction was used to isolate the differences. The alpha-type error was set at 0.05. All specimens had measurable push-out values and no premature failure occurred. There were significant differences among the materials (p <0.05). The Biodentine specimens had the highest push-out bond strength values (p < 0.05). MTA HP had significantly higher bond strength than White MTA (p < 0.05). MTA HP showed better push-out bond strength than its predecessor, White MTA; however, Biodentine had higher dislodgment resistance than both MTA formulations. PMID:27305515

  5. Improvement of in vitro physicochemical properties and osteogenic activity of calcium sulfate cement for bone repair by dicalcium silicate

    International Nuclear Information System (INIS)

    Highlights: • Dicalcium silicate can improve osteogenic activity of calcium sulfate cement. • The higher the calcium sulfate content, the shorter the setting time in the composite cement. • The results were useful for designing calcium-based cement with optimal properties. -- Abstract: An ideal bone graft substitute should have the same speed of degradation as formation of new bone tissue. To improve the properties of calcium sulfate hemihydrate (CSH) featured for its rapid resorption, a low degradation material of dicalcium silicate (DCS) was added to the CSH cement. This study examined the effect of DCS (20, 40, 60 and 80 wt%) on the in vitro physicochemical properties and osteogenic activities of the calcium-based composite cements. The diametral tensile strength, porosity and weight loss of the composite cements were evaluated before and after soaking in a simulated body fluid (SBF). The osteogenic activities, such as proliferation, differentiation and mineralization, of human mesenchymal stem cells (hMSCs) seeded on cement surfaces were also examined. As a result, the greater the DCS amount, the higher the setting time was in the cement. Before soaking in SBF, the diametral tensile strength of the composite cements was decreased due to the introduction of DCS. On 180-day soaking, the composite cements containing 20, 40, 60 and 80 wt% DCS lost 80%, 69%, 61% and 44% in strength, respectively. Regarding in vitro bioactivity, the DCS-rich cements were covered with clusters of apatite spherulites after soaking for 7 days, while there was no formation of apatite spherulites on the CSH-rich cement surfaces. The presence of DCS could reduce the degradation of the CSH cements, as evidenced in the results of weight loss and porosity. More importantly, DCS may promote effectively the cell proliferation, proliferation and mineralization. The combination of osteogenesis of DCS and degradation of CSH made the calcium-based composite cements an attractive choice for

  6. The thermophysical properties of calcium and barium zirconium phosphate

    Energy Technology Data Exchange (ETDEWEB)

    Gregg, Daniel J., E-mail: daniel.gregg@ansto.gov.au; Karatchevtseva, Inna; Triani, Gerry; Lumpkin, Gregory R.; Vance, Eric R.

    2013-10-15

    The thermophysical and structural properties of calcium and barium zirconium phosphate ceramics (CZP and BZP) have been investigated for their potential candidacy as actinide hosts for inert matrix fuels (IMF) in nuclear reactors. These phosphate ceramics, which can accommodate minor actinides as well as the resulting fission products, are found to be thermally stable to 1600 °C in air, however they begin to decompose in an inert atmosphere above approximately 1400 °C. The heat capacity, thermal conductivity and bulk thermal-expansion were measured from room temperature up to 1200 °C. Structural changes in this temperature region as well as the anisotropic thermal-expansion behaviour were studied using high-temperature X-ray diffraction. A phase change from R-3 to R-3c was identified for Ba{sub 0.5}Zr{sub 2}(PO{sub 4}){sub 3} near 880 °C. The thermal conductivity for these ceramics at 1000 °C was found to be 1.0 W m{sup −1} K{sup −1}, a relatively low thermal conductivity that was increased to 5.0 W m{sup −1} K{sup −1} at 1000 °C for BZP:Ni (25:75 mass ratio) cermet composites.

  7. Calcium phosphate nanoparticles functionalized with a dimethacrylate monomer

    International Nuclear Information System (INIS)

    The synthesis of calcium phosphate nanoparticles may include modifying agents to tailor particle size, reduce agglomeration and add specific functionalities. This study describes the synthesis of dicalcium phosphate dihydrate (DCPD) nanoparticles functionalized with triethylene glycol dimethacrylate (TEGDMA), added to one of the reacting solutions, with the purpose of reducing agglomeration and improving the compatibility with vinyl-based resin matrices. The nanoparticles were characterized by X-ray diffraction (XRD), Fourier-transformed infrared spectroscopy (FTIR), elemental analysis, thermogravimetric analysis (TGA), transmission electronic microscopy (TEM), dynamic light scattering (DLS), and surface area (BET). As controls, proprietary DCPD nanoparticles and nanoparticles synthesized without the addition of TEGDMA (“bare”) were subjected to the same analytical methods. XRD revealed a similar crystalline structure of the synthesized materials in comparison to the proprietary nanoparticles. The presence of a TEGDMA layer was confirmed by elemental analysis and TGA, corresponding to a mass fraction of 8.5%. FTIR analysis of the functionalized nanoparticles revealed the suppression of some absorbance bands found in the neat TEGDMA. A chemisorption mechanism between TEGDMA and the surface of primary particles by ion–dipole interaction involving TEGDMA oxyethylene, and also an interaction mechanism between the particle surface and terminal-CH3 groups are proposed. Functionalized nanoparticles showed 3 to 11 times higher surface area than the controls, in agreement with DLS data, indicating lower agglomeration. - Highlights: • Dicalcium phosphate (DCPD) nanoparticles were functionalized ab initio using TEGDMA. • Triethylene glycol dimethacrylate was chosen due to its polymerizable vinyl groups. • These nanoparticles would have a better interaction with dimethacrylate resins. • An ion–dipole chemisorption mechanism between DCPD and TEGDMA is described

  8. Calcium Silicate-Based Cements Associated with Micro- and Nanoparticle Radiopacifiers: Physicochemical Properties and Bioactivity

    OpenAIRE

    BOSSO-MARTELO, Roberta; Juliane Maria GUERREIRO-TANOMARU; Viapiana, Raqueli; Berbert, Fábio Luis Camargo Vilella; Basso Bernardi, Maria Inês; Tanomaru-Filho, Mario

    2015-01-01

    Objective. The aim of this study was to evaluate the physicochemical properties and bioactivity of two formulations of calcium silicate-based cements containing additives (CSCM) or resin (CSCR), associated with radiopacifying agents zirconium oxide (ZrO2) and niobium oxide (Nb2O5) as micro- and nanoparticles; calcium tungstate (CaWO4); and bismuth oxide (Bi2O3). MTA Angelus was used as control. Methods. Surface features and bioactivity were evaluated by scanning electron microscopy and the ch...

  9. Particle size of a new endodontic cement compared to Root MTA and calcium hydroxide

    OpenAIRE

    Soheilipour, Elham; Kheirieh, Sanam; Madani, Majid; Akbarzadeh Baghban, Alireza; Asgary, Saeed

    2009-01-01

    INTRODUCTION: Particle size and distribution can influence the properties of materials. This study analyzed and compared the particle size of Root MTA, calcium hydroxide (CH), and a new endodontic cement called calcium enriched material (CEM). MATERIALS AND METHODS: The particle size of each material was analyzed three times using 0.05 mg of test material with a particle size analyzer. The particle size distribution ranges, the cumulative percentage and the mean of particle sizes were calcula...

  10. Precipitation of calcium carbonate and calcium phosphate under diffusion controlled mixing

    Energy Technology Data Exchange (ETDEWEB)

    Tsigabu Gebrehiwet; James R. Henriksen; Luanjing Guo; Don T. Fox; Hai Huang; Lee Tu; Yoshiko Fujita; Robert W. Smith; George Redden

    2014-07-01

    Multi-component mineral precipitation in porous, subsurface environments is challenging to simulate or engineer when in situ reactant mixing is controlled by diffusion. In contrast to well-mixed systems, the conditions that favor mineral precipitation in porous media are distributed along chemical gradients, which evolve spatially due to concurrent mineral precipitation and modification of solute transport in the media. The resulting physical and chemical characteristics of a mixing/precipitation zone are a consequence of coupling between transport and chemical processes, and the distinctive properties of individual chemical systems. We examined the spatial distribution of precipitates formed in “double diffusion” columns for two chemical systems, calcium carbonate and calcium phosphate. Polyacrylamide hydrogel was used as a low permeability, high porosity medium to maximize diffusive mixing and minimize pressure- and density-driven flow between reactant solutions. In the calcium phosphate system, multiple, visually dense and narrow bands of precipitates were observed that were reminiscent of previously reported Liesegang patterns. In the calcium carbonate system, wider precipitation zones characterized by more sparse distributions of precipitates and a more open channel structure were observed. In both cases, formation of precipitates inhibited, but did not necessarily eliminate, continued transport and mixing of the reactants. A reactive transport model with fully implicit coupling between diffusion, chemical speciation and precipitation kinetics, but where explicit details of nucleation processes were neglected, was able to qualitatively simulate properties of the precipitation zones. The results help to illustrate how changes in the physical properties of a precipitation zone depend on coupling between diffusion-controlled reactant mixing and chemistry-specific details of precipitation kinetics.

  11. 椎弓根螺钉系统加自固化磷酸钙人工骨灌注治疗胸腰椎骨折%Treatment of thoracolumbar vertebrae fractures with vertebral pedicle screw system and artificial bones filled with autosolidification calcium phosphate cement

    Institute of Scientific and Technical Information of China (English)

    曾忠友; 金才益; 陆金荣; 王斌; 徐阿炳

    2001-01-01

    目的探讨应用椎弓根螺钉系统及自固化磷酸钙人工骨(ACPC)灌注治疗胸腰椎骨折的效果。方法 1999年4月始,选择18例胸腰椎骨折患者,其中压缩型12例,爆裂型6例。伤后6 h~7 d行椎弓根螺钉系统固定、复位,同时加ACPC灌注伤椎。结果 18例患者除2例神经功能A级脊髓神经症状无改善外,其余均有Ⅰ~Ⅲ级的恢复,脊柱后凸角平均恢复21°,伤椎前缘高度平均恢复至98%,伤椎后缘侵入椎管骨块明显回纳。随访10~16个月,平均11.6个月。随访期间无内固定松动及断裂现象,无慢性腰背痛,伤椎高度及脊柱生理弧度无丢失。结论胸腰椎压缩型骨折是使用ACPC的最佳适应证。如术前影像检查明确有双侧椎弓根骨折,则为禁忌。只要手术适应证选择适当,术中操作仔细,椎弓根螺钉系统加ACPC灌注治疗胸腰椎骨折是一有效而又安全的方法,特别是后期伤椎高度和脊柱生理弧度得到很好的维持。%Objective To study the effect of vertebral pedicle screw system and artificial bones filled with autosolidification calcium phosphate cement(ACPC) on thoracolumbar vertebrae fractures.  Methods A total of 18 patients with thoracolumbar vertebrae fractures and with operative indications were treated with vertebral pedicle screw system and artificial bones filled with ACPC.  Results  Except 2 patients with the spinal cord function for Grade A, all the patients had the average improvement of Degree I to Degree Ⅲ on the aspect of spinal cord function. The kyphotic angle recovered averagely for 21°, the anterior height of the injured vertebral body was averagely restored to 98% of the normal, and the bone fragments that invaded into the spinal canal were obviously restored. During the following-up, loose or breakage of the internal fixation was not found, and there was no chronic lumbar back pain or loss of the normal spine curve and the

  12. Mechanical Behavior and Thermal Stability of Acid-Base Phosphate Cements and Composites Fabricated at Ambient Temperature

    OpenAIRE

    Colorado, Henry A.

    2013-01-01

    This dissertation presents the study of the mechanical behavior and thermal stability of acid-base phosphate cements (PCs) and composites fabricated at ambient temperature. These materials are also known as chemically bonded phosphate ceramics (CBPCs). Among other advantages of using PCs when compared with traditional cements are the better mechanical properties (compressive and flexural strength), lower density, ultra-fast (controllable) setting time, controllable pH, and an environmentally ...

  13. Calcium phosphate granulation in anaerobic treatment of black water: a new approach to phosphorus recovery.

    Science.gov (United States)

    Tervahauta, Taina; van der Weijden, Renata D; Flemming, Roberta L; Hernández Leal, Lucía; Zeeman, Grietje; Buisman, Cees J N

    2014-01-01

    Recovery of phosphorus from wastewater as calcium phosphate could diminish the need for mining of scarce phosphate rock resources. This study introduces a novel approach to phosphorus recovery by precipitation of calcium phosphate granules in anaerobic treatment of black water. The granules formed in the Upflow Anaerobic Sludge Blanket (UASB) reactor at lab- and demonstration-scale were analyzed for chemical composition and mineralogy by Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES), Electron microprobe (EMP), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy and micro X-ray Diffraction (XRD). The granules had a diameter of 1-2 mm, organic content of 33 wt%, and phosphorus content of 11-13 wt%. Three calcium phosphate phases were identified in the granules: hydroxyapatite, calcium phosphate hydrate and carbonated hydroxyapatite. Without any addition of chemicals, 7 gP/person/year can be recovered with the calcium phosphate granules, representing 2% of the incoming phosphorus in the UASB reactor. As the heavy metal content was lower compared to other phosphorus recovery products, phosphate rock and phosphorus fertilizer, the calcium phosphate granules could be considered as a new phosphorus product. PMID:24183558

  14. Bioactive PMMA bone cement prepared by modification with methacryloxypropyltrimethoxysilane and calcium chloride.

    Science.gov (United States)

    Miyazaki, Toshiki; Ohtsuki, Chikara; Kyomoto, Masayuki; Tanihara, Masao; Mori, Akiko; Kuramoto, Kou-ichi

    2003-12-15

    Bone cement consisting of polymethylmethacrylate (PMMA) powder and methylmethacrylate (MMA) liquid is used extensively for fixation of implants such as artificial hip joints with living bone. This type of cement, however, does not show direct bonding to the living body, and hence the fixation is liable to loosen over a long implantation period. Bioactive materials have received much attention because of their capability for bone-bonding, i.e., bioactivity, when implanted in bony defects. Osteoconduction of the bioactive materials is caused by formation of a bone-like apatite layer through a surface reaction between the material and surrounding body fluid. The apatite formation can be induced by a silanol (Sibond;OH) group formed on the materials as well as a dissolution of calcium ion (Ca(2+)) from the material. Incorporation of alkoxysilane and calcium chloride (CaCl(2)) may provide PMMA bone cement with bioactivity, because alkoxysilane gives Sibond;OH after hydrolysis, whereas CaCl(2) releases Ca(2+). In this study, we investigated the potential on bioactivity of the modified PMMA bone cement with alkoxysilane and calcium chloride. PMMA powder was mixed with various amounts of CaCl(2), and MMA liquid with various amounts of 3-methacryloxypropyltrimethoxysilane (MPS). The mixed paste was immersed in a simulated body fluid (Kokubo solution) that has a similar concentration in inorganic constituents to human blood plasma. After soaking for various periods, apatite formation on the cement was examined. Apatite formation was observed by the addition of CaCl(2) with contents of 16 mass % and more. Incorporation of MPS accelerates the apatite formation. Setting time of the cement was significantly elongated after the addition of MPS, whereas compressive strength significantly decreased with increasing the contents of CaCl(2) and MPS. The hardened cement containing 20 mass % of CaCl(2) in the powder and 20 mass % of MPS in the liquid showed a tendency to be more

  15. Evaluation of antibacterial and antifungal activity of new calcium-based cement (Biodentine) compared to MTA and glass ionomer cement

    Science.gov (United States)

    Bhavana, Vankayala; Chaitanya, Krishna Popuri; Gandi, Padma; Patil, Jayaprakash; Dola, Binoy; Reddy, Rahul B.

    2015-01-01

    Objective: To evaluate the antibacterial and antifungal properties of calcium-based cement, Biodentine (Ca3SiO2), compared to commercial glass ionomer cements (GICs) and mineral trioxide aggregate (MTA). Materials and Methods: Pellets of GICs, ProRoot MTA, and Biodentine were prepared to test the influence of these cements on the growth of four oral microbial strains: Streptococcus mutans, Enterococcus faecalis, Escherichia coli, and Candida albicans; using agar diffusion method. Wells were formed by removing the agar and the manipulated materials were immediately placed in the wells. The pellets were lodged in seeded plates and the growth inhibition diameter around the material was measured after 24-72 h incubation at 37°C. The data were analyzed using analysis of variance (ANOVA) test to compare the differences among the three cements at different concentrations. Results: Test indicates that the antimicrobial activity of Biodentine, on all the microorganisms tested, was very strong, showing a mean inhibition zone of 3.2 mm, which extends over time towards all the strains. For Biodentine, GIC, and MTA, the diameters of the inhibition zones for S. mutans were significantly larger than for E. faecalis, Candida, and E. coli (P Biodentine created larger inhibition zones than MTA and GIC. PMID:25657526

  16. Evaluation of antibacterial and antifungal activity of new calcium-based cement (Biodentine compared to MTA and glass ionomer cement

    Directory of Open Access Journals (Sweden)

    Vankayala Bhavana

    2015-01-01

    Full Text Available Objective: To evaluate the antibacterial and antifungal properties of calcium-based cement, Biodentine (Ca 3 SiO 2 , compared to commercial glass ionomer cements (GICs and mineral trioxide aggregate (MTA. Materials and Methods: Pellets of GICs, ProRoot MTA, and Biodentine were prepared to test the influence of these cements on the growth of four oral microbial strains: Streptococcus mutans, Enterococcus faecalis, Escherichia coli, and Candida albicans; using agar diffusion method. Wells were formed by removing the agar and the manipulated materials were immediately placed in the wells. The pellets were lodged in seeded plates and the growth inhibition diameter around the material was measured after 24-72 h incubation at 37°C. The data were analyzed using analysis of variance (ANOVA test to compare the differences among the three cements at different concentrations. Results: Test indicates that the antimicrobial activity of Biodentine, on all the microorganisms tested, was very strong, showing a mean inhibition zone of 3.2 mm, which extends over time towards all the strains. For Biodentine, GIC, and MTA, the diameters of the inhibition zones for S. mutans were significantly larger than for E. faecalis, Candida, and E. coli (P < 0.05. Conclusion: All materials showed antimicrobial activity against the tested strains except for GIC on Candida. Largest inhibition zone was observed for Streptococcus group. Biodentine created larger inhibition zones than MTA and GIC.

  17. Stabilization of ZnCl2-containing wastes using calcium sulfoaluminate cement: cement hydration, strength development and volume stability.

    Science.gov (United States)

    Berger, Stéphane; Cau Dit Coumes, Céline; Le Bescop, Patrick; Damidot, Denis

    2011-10-30

    The potential of calcium sulfoaluminate (CSA) cement was investigated to solidify and stabilize wastes containing large amounts of soluble zinc chloride (a strong inhibitor of Portland cement hydration). Hydration of pastes and mortars prepared with a 0.5 mol/L ZnCl(2) mixing solution was characterized over one year as a function of the gypsum content of the binder and the thermal history of the material. Blending the CSA clinker with 20% gypsum enabled its rapid hydration, with only very small delay compared with a reference prepared with pure water. It also improved the compressive strength of the hardened material and significantly reduced its expansion under wet curing. Moreover, the hydrates assemblage was less affected by a thermal treatment at early age simulating the temperature rise and fall occurring in a large-volume drum of cemented waste. Fully hydrated materials contained ettringite, amorphous aluminum hydroxide, strätlingite, together with AFm phases (Kuzel's salt associated with monosulfoaluminate or Friedel's salt depending on the gypsum content of the binder), and possibly C-(A)-S-H. Zinc was readily insolubilized and could not be detected in the pore solution extracted from cement pastes. PMID:21889260

  18. Lipid-coated nano-calcium-phosphate (LNCP) for gene delivery

    OpenAIRE

    Zhou, Chenguang; Yu, Bo; Yang, Xiaojuan; Huo, Tianyao; Lee, L. James; Barth, Rolf F; Lee, Robert J.

    2010-01-01

    While calcium-phosphate has been used to deliver plasmid DNA (pDNA) for decades, the method is typically characterized by low and irreproducible transfection efficiency relative to the other non-viral approaches, such as liposomes and polymers. Here we report a novel gene transfer vector comprising lipid-coated nano-calcium-phosphate (LNCP) that provides consistently efficient and satisfactory pDNA delivery. It is based on core-shell nanoparticles comprising a calcium-phosphate core and a cat...

  19. Influence of sodium borate on the early age hydration of calcium sulfoaluminate cement

    International Nuclear Information System (INIS)

    Calcium sulfoaluminate (CSA) cements are potential candidates for the conditioning of radioactive wastes with high sodium borate concentrations. This work thus investigates early age hydration of two CSA cements with different gypsum contents (0 to 20%) as a function of the mixing solution composition (borate and NaOH concentrations). Gypsum plays a key role in controlling the reactivity of cement. When the mixing solution is pure water, increasing the gypsum concentration accelerates cement hydration. However, the reverse is observed when the mixing solution contains sodium borate. Until gypsum exhaustion, the pore solution pH remains constant at ~ 10.8, and a poorly crystallized borate compound (ulexite) precipitates. A correlation is established between this transient precipitation and the hydration delay. Decreasing the gypsum content in the binder, or increasing the sodium content in the mixing solution, are two ways of reducing the stability of ulexite, thus decreasing the hydration delay

  20. Influence of sodium borate on the early age hydration of calcium sulfoaluminate cement

    Energy Technology Data Exchange (ETDEWEB)

    Champenois, Jean-Baptiste; Dhoury, Mélanie [CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze Cedex (France); Cau Dit Coumes, Céline, E-mail: celine.cau-dit-coumes@cea.fr [CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze Cedex (France); Mercier, Cyrille [LMCPA, Université de Valenciennes et du Hainaut Cambrésis, 59600 Maubeuge (France); Revel, Bertrand [Centre Commun de Mesure RMN, Université Lille1 Sciences Technologies, Cité Scientifique, 59655 Villeneuve d' Ascq Cedex (France); Le Bescop, Patrick [CEA, DEN, DPC, SECR, F-91192 Gif-sur-Yvette (France); Damidot, Denis [Ecole des Mines de Douai, LGCgE-GCE, 59508 Douai (France)

    2015-04-15

    Calcium sulfoaluminate (CSA) cements are potential candidates for the conditioning of radioactive wastes with high sodium borate concentrations. This work thus investigates early age hydration of two CSA cements with different gypsum contents (0 to 20%) as a function of the mixing solution composition (borate and NaOH concentrations). Gypsum plays a key role in controlling the reactivity of cement. When the mixing solution is pure water, increasing the gypsum concentration accelerates cement hydration. However, the reverse is observed when the mixing solution contains sodium borate. Until gypsum exhaustion, the pore solution pH remains constant at ~ 10.8, and a poorly crystallized borate compound (ulexite) precipitates. A correlation is established between this transient precipitation and the hydration delay. Decreasing the gypsum content in the binder, or increasing the sodium content in the mixing solution, are two ways of reducing the stability of ulexite, thus decreasing the hydration delay.

  1. Preparation and in vitro evaluation of strontium-doped calcium silicate/gypsum bioactive bone cement

    International Nuclear Information System (INIS)

    The combination of two or more bioactive components with different biodegradability could cooperatively improve the physicochemical and biological performances of the biomaterials. Here we explore the use of α-calcium sulfate hemihydrate (α-CSH) and calcium silicate with and without strontium doping (Sr-CSi, CSi) to fabricate new bioactive cements with appropriate biodegradability as bone implants. The cements were fabricated by adding different amounts (0–35 wt%) of Sr-CSi (or CSi) into the α-CSH-based pastes at a liquid-to-solid ratio of 0.4. The addition of Sr-CSi into α-CSH cements not only led to a pH rise in the immersion medium, but also changed the surface reactivity of cements, making them more bioactive and therefore promoting apatite mineralization in simulated body fluid (SBF). The impact of additives on long-term in vitro degradation was evaluated by soaking the cements in Tris buffer, SBF, and α-minimal essential medium (α-MEM) for a period of five weeks. An addition of 20% Sr-CSi to α-CSH cement retarded the weight loss of the samples to 36% (in Tris buffer), 43% (in SBF) and 54% (in α-MEM) as compared with the pure α-CSH cement. However, the addition of CSi resulted in a slightly faster degradation in comparison with Sr-CSi in these media. Finally, the in vitro cell-ion dissolution products interaction study using human fetal osteoblast cells demonstrated that the addition of Sr-CSi improved cell viability and proliferation. These results indicate that tailorable bioactivity and biodegradation behavior can be achieved in gypsum cement by adding Sr-CSi, and such biocements will be of benefit for enhancing bone defect repair. (paper)

  2. Fibroblast and osteoblast adhesion and morphology on calcium phosphate surfaces

    Directory of Open Access Journals (Sweden)

    Baxter L. C.

    2002-09-01

    Full Text Available Implant loosening in bone fixation is an unresolved complication associated with internal fixation. It is generally accepted that this problem can be overcome by modifying the implant/bone interface for improved osseointegration. This is achieved, in part, by hydroxyapatite (HA or tricalcium phosphate coatings. Unfortunately, the benefits of these coatings are constrained by not only the generally low strength of their adhesion to the implant surface but also the limited cohesion within their layers. Anodic Plasma-chemical treatment (APC has been developed to incorporate electrolytes and produce coatings with various microtopographies and strong adhesion to implants. In this in vitro study fibroblast and osteoblast morphologies and adhesion to various substrates were evaluated using qualitative and quantitative methods. The substrates were Thermanox plastic and commercially pure titanium. The latter were surface-treated using several different methods: conventional anodisation, plasma spraying of HA and anodic plasma-chemical (APC treatment in an electrolyte solution containing either calcium and phosphate (APC-CaP or phosphoric acid (APC-P. Both osteoblasts and fibroblasts showed extensive cell spreading, total cell area and greatest amount of adhesion, with defined adhesion patterns on the Thermanox plastic, anodised titanium, and the two APC-CaP substrates. With fibroblasts, almost no cell spreading and very low adhesion, was observed in cells cultured on the APC-P and HA surfaces. The extent of cell spreading correlated with the area of focal adhesions as assessed by the amount of vinculin labelling. The Thermanox plastic, anodised titanium, and the two APC-CaP substrates were the most cytocompatible substrates with regard to this in vitro evaluation.

  3. The Mechanical Properties and Hydration Characteristics of Cement Pastes Containing Added-calcium Coal Gangue

    Institute of Scientific and Technical Information of China (English)

    LI Dongxu; SONG Xuyan

    2008-01-01

    The mechanical properties of several kinds of coal gangue calcined with limestone were Researched so as to find the optimum way of calcinations with limestone. Mierostructure and property of hydration process of cement pastes containing added-calcium coal gangue were analyzed by means of scanning electron microscope (SEM) and method of mercury in trusion poremeasurement (MIP), etc. The experiment can approve those results: when proper amounst of gypsum and fluorite were taken as mineralizers in the course of calcinations of added-calcium coal gangue, activity of coal gangue can be effectively improved. The results of mechanical property and structural characteristic such as hydration process, hydration product and microstructure etc. of cement pastes containing added-calcium coal gangue are consistent.

  4. The mechanical properties and hydration characteristics of cement pastes containing added-calcium coal gangue

    Energy Technology Data Exchange (ETDEWEB)

    Dongxu Li; Xuyan Song [Nanjing University of Technology, Nanjing (China). College of Material Science and Engineering

    2008-04-15

    The mechanical properties of several kinds of coal gangue calcined with limestone were researched so as to find the optimum way of calcinations with limestone. The microstructure and property of hydration process of cement pastes containing added-calcium coal gangue were analyzed by means of scanning electron microscope (SEM) and the method of mercury in trusion poremeasurement. When the proper amounst of gypsum and fluorite were taken as mineralizers in the course of calcinations of added-calcium coal gangue, the activity of coal gangue can be effectively improved. The results of mechanical property and structural characteristics such as hydration, hydration products and microstructure etc. of cement pastes containing added-calcium coal gangue are consistent.

  5. Early-age hydration and volume change of calcium sulfoaluminate cement-based binders

    Science.gov (United States)

    Chaunsali, Piyush

    Shrinkage cracking is a predominant deterioration mechanism in structures with high surface-to-volume ratio. One way to allay shrinkage-induced stresses is to use calcium sulfoaluminate (CSA) cement whose early-age expansion in restrained condition induces compressive stress that can be utilized to counter the tensile stresses due to shrinkage. In addition to enhancing the resistance against shrinkage cracking, CSA cement also has lower carbon footprint than that of Portland cement. This dissertation aims at improving the understanding of early-age volume change of CSA cement-based binders. For the first time, interaction between mineral admixtures (Class F fly ash, Class C fly ash, and silica fume) and OPC-CSA binder was studied. Various physico-chemical factors such as the hydration of ye'elimite (main component in CSA cement), amount of ettringite (the main phase responsible for expansion in CSA cement), supersaturation with respect to ettringite in cement pore solution, total pore volume, and material stiffness were monitored to examine early-age expansion characteristics. This research validated the crystallization stress theory by showing the presence of higher supersaturation level of ettringite, and therefore, higher crystallization stress in CSA cement-based binders. Supersaturation with respect to ettringite was found to increase with CSA dosage and external supply of gypsum. Mineral admixtures (MA) altered the expansion characteristics in OPC-CSA-MA binders with fixed CSA cement. This study reports that fly ash (FA) behaves differently depending on its phase composition. The Class C FA-based binder (OPC-CSA-CFA) ceased expanding beyond two days unlike other OPC-CSA-MA binders. Three factors were found to govern expansion of CSA cement-based binders: 1) volume fraction of ettringite in given pore volume, 2) saturation level of ettringite, and 3) dynamic modulus. Various models were utilized to estimate the macroscopic tensile stress in CSA cement

  6. Hydration studies of calcium sulfoaluminate cements blended with fly ash

    OpenAIRE

    Garcia-Maté, Marta; De la Torre, Angeles G; León-Reina, Laura; Aranda, Miguel A. G.; Santacruz, Isabel

    2013-01-01

    The main objective of this work is to study the hydration and properties of calciumsulfoaluminate cement pastes blended with fly ash (FA) and the corresponding mortars at different hydration ages. Laboratory X-ray powder diffraction, rheological studies, thermal analysis, porosimetry and compressive strength measurements were performed. The analysis of the diffraction data by Rietveld method allowed quantifying crystalline phases and overall amorphous contents. The studied paramet...

  7. Effect of pH and Lidocaine on the Compressive Strength of Calcium Enriched Mixture Cement

    Directory of Open Access Journals (Sweden)

    Sobhnamayan F

    2015-12-01

    Full Text Available Statement of Problem: The pH of the human abscess has been measured as low as 5.0. This low pH could potentially inhibit setting reactions, affect adhesion, or increase the solubility of root end filling materials hence affect the compressive strength. Moreover, root end filling materials might expose or even mix with lidocaine HCL during periapical surgery. Objectives: The aim of this in vitro study was to evaluate the effect of acidic pH and lidocaine on the compressive strength of calcium-enriched mixture (CEM. Materials and Methods: CEM was mixed according to the manufacturer’s instructions or with lidocaine (L, and condensed into 6 × 4 mm split moulds. The samples were exposed to phosphate buffered saline (PBS at pH 5 or 7.4 for 7 or 28 days. Cylindrical blocks of CEM (total number = 120 and 15 for each group were subjected to compressive strength test using a universal testing machine. Data were analysed using three-factor analysis of variance (ANOVA. Results: Regardless of pH and time, significant differences were not found between lidocaine groups and the groups that were mixed according to the manufacturer’s instruction (p = 0.083. For both mixing agents, regardless of time, there were no significant differences between the two pH levels (p = 0.157. Regardless of the material and pH, there was a significant increase in the compressive strength from days 7 to 28 (p < 0.001. Conclusions: Mixtures with lidocaine and exposure to an acidic environment had no adverse effects on the compressive strength of CEM Cement.

  8. Randomized crossover study comparing the phosphate-binding efficacy of calcium ketoglutarate versus calcium carbonate in patients on chronic hemodialysis.

    Science.gov (United States)

    Bro, S; Rasmussen, R A; Handberg, J; Olgaard, K; Feldt-Rasmussen, B

    1998-02-01

    The objective of the study was to evaluate the phosphate-binding efficacy, side effects, and cost of therapy of calcium ketoglutarate granulate as compared with calcium carbonate tablets in patients on chronic hemodialysis. The study design used was a randomized, crossover open trial, and the main outcome measurements were plasma ionized calcium levels, plasma phosphate levels, plasma intact parathyroid hormone (PTH) levels, requirements for supplemental aluminum-aminoacetate therapy, patient tolerance, and cost of therapy. Nineteen patients on chronic hemodialysis were treated with a dialysate calcium concentration of 1.25 mmol/L and a fixed alfacalcidol dose for at least 2 months. All had previously tolerated therapy with calcium carbonate. Of the 19 patients included, 10 completed both treatment arms. After 12 weeks of therapy, the mean (+/-SEM) plasma ionized calcium level was significantly lower in the ketoglutarate arm compared with the calcium carbonate arm (4.8+/-0.1 mg/dL v 5.2+/-0.1 mg/dL; P = 0.004), whereas the mean plasma phosphate (4.5+/-0.3 mg/dL v 5.1+/-0.1 mg/dL) and PTH levels (266+/-125 pg/mL v 301+/-148 pg/mL) did not differ significantly between the two treatment arms. Supplemental aluminum-aminoacetate was not required during calcium ketoglutarate treatment, while two patients needed this supplement when treated with calcium carbonate. Five of 17 (29%) patients were withdrawn from calcium ketoglutarate therapy within 1 to 2 weeks due to intolerance (anorexia, vomiting, diarrhea, general uneasiness), whereas the remaining 12 patients did not experience any side effects at all. The five patients with calcium ketoglutarate intolerance all had pre-existing gastrointestinal symptoms; four of them had received treatment with cimetidine or omeprazol before inclusion into the study. Calculations based on median doses after 12 weeks showed that the cost of the therapy in Denmark was 10 times higher for calcium ketoglutarate compared with calcium

  9. Assessment of Protective Effect of Amorphous Calcium Phosphate-Caseine

    Directory of Open Access Journals (Sweden)

    Anousheh Rashed-Mohassel

    2014-07-01

    Full Text Available Background: One of the complications of Iron drop recommended for 6-24 months children is the potential reduction in microhardness of primary tooth enamel because of low pH. The objective of this study is to assess the protective effect of amorphous calcium phosphate caseine phosphopeptide (ACP-CPP and silicone oil in primary teeth. Materials and Methods: Thirty extracted primary anterior teeth were divided into three equal groups. The initial micro hardness was measured by Vicker’s microhardness tester. The first group without a protective layer and the second and third group after application of ACP-CPP and silicone oil respectively, were immersed in iron drop. Microhardness was remeasured. One tooth in each group along with a tooth not exposed to iron drop were randomly chosen for SEM qualitative analysis. Analysis was performed with Repeated measures ANOVA with SPSS-18. Results: All groups exhibited significant decrease of micro hardness (p=0.001, however, no contrasting pattern was found between various groups. Conclusion: Neither ACP-CPP nor silicone oil could not provide a significant protection against micro hardness reduction after exposure to iron drop

  10. Dibasic calcium phosphate dihydrate, USP material compatibility with gamma radiation

    Science.gov (United States)

    Betancourt Quiles, Maritza

    Gamma radiation is a commonly used method to reduce the microbial bioburden in compatible materials when it is applied at appropriate dose levels. Gamma irradiation kills bacteria and mold by breaking down the organism’s DNA and inhibiting cell division. The purpose of this study is to determine the radiation dosage to be used to treat Dibasic Calcium Phosphate Dihydrate, USP (DCPD) and to evaluate its physicochemical effects if any, on this material. This material will be submitted to various doses of gamma radiation that were selected based on literature review and existing regulations that demonstrate that this method is effective to reduce or eliminate microbial bioburden in natural source and synthetic materials. Analytical testing was conducted to the DCPD exposed material in order to demonstrate that gamma radiation does not alter the physicochemical properties and material still acceptable for use in the manufacture of pharmaceutical products. The results obtained through this study were satisfactory and demonstrated that the gamma irradiation dosages from 5 to 30 kGy can be applied to DCPD without altering its physicochemical properties. These are supported by the Assay test data evaluation of lots tested before and after gamma irradiation implementation that show no significant statistical difference between irradiated and non irradiated assay results. The results of this study represent an achievement for the industry since they provide as an alternative the use of Gamma irradiation technology to control the microbial growth in DCPD.

  11. Effect of casein phosphopeptide-amorphous calcium phosphate and acidulated phosphate fluoride gel on erosive enamel wear

    OpenAIRE

    Maryam HajeNorouz Ali Tehrani; Maryam Ghafournia; Pouran Samimi; Omid Savabi; Iman Parisay; Navid Askari; Seyed-Hossein Abtahi

    2011-01-01

    Background: Some studies have shown that casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and acidulated phosphate fluoride (APF) gel can protect teeth against erosion. The aim of this study was to assess whether CPP-ACP and fluoride could reduce enamel wear rates under erosive conditions simulating abrasion and acidic diet regimen. Materials and Methods: Enamel specimens consisted of 3 experimental groups (receiving CPP-ACP, APF or both) and a control group. Specimens were sub...

  12. Effect of casein phosphopeptide-amorphous calcium phosphate and acidulated phosphate fluoride gel on erosive enamel wear

    OpenAIRE

    Tehrani, Maryam HajeNorouz Ali; Ghafournia, Maryam; Samimi, Pouran; Savabi, Omid; Parisay, Iman; Askari, Navid; Abtahi, Seyed-Hossein

    2011-01-01

    Background: Some studies have shown that casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and acidulated phosphate fluoride (APF) gel can protect teeth against erosion. The aim of this study was to assess whether CPP-ACP and fluoride could reduce enamel wear rates under erosive conditions simulating abrasion and acidic diet regimen. Materials and Methods: Enamel specimens consisted of 3 experimental groups (receiving CPP-ACP, APF or both) and a control group. Specimens were subject...

  13. Bioactive calcium phosphate coating formed on micro-arc oxidized magnesium by chemical deposition

    Energy Technology Data Exchange (ETDEWEB)

    Liu, G.Y. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Hu, J., E-mail: hujin@hit.edu.cn [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Ding, Z.K.; Wang, C. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China)

    2011-01-01

    In order to improve the bioactivity of the micro-arc oxidized magnesium, a calcium phosphate coating was formed on the surface of micro-arc oxidized magnesium using a chemical method. The microstructures of the substrate and the calcium phosphate coating before and after the simulated body fluids (SBF) incubation were characterized by X-ray diffraction, Fourier-transformed infrared spectroscopy and scanning electron microscopy. The results showed that the calcified coating was composed of calcium deficient hydroxyapatite (HA) and dicalcium phosphate dihydrate (DCPD). After SBF incubation, some new apatite formation on the calcified coating surface from SBF could be found. The corrosion behaviours of the samples in SBF were also investigated by potentiodynamic polarization curves and immersion tests. The results showed that calcium phosphate coating increased the corrosion potential, and decreased the hydrogen gas release.

  14. Characterization of a silver-incorporated calcium phosphate film by RBS and its antimicrobial effects

    International Nuclear Information System (INIS)

    A thin calcium phosphate film was synthesized on both commercially pure Ti and Si wafers by electron beam evaporation of hydroxyapatite as an evaporant with simultaneous Ar ion beam bombardments. Silver was introduced into an ion-beam-assisted deposition of a calcium phosphate thin film for antimicrobial effect. The amount of incorporated silver ions was controlled by immersing calcium-phosphate-coated samples in different AgNO3 concentrations, and Rutherford backscattering spectrometry (RBS) was employed to measure the amounts of substituted silver. The higher concentration of silver in the calcium phosphate film was more effective in reducing the bacteria of Escherichia coli ATCC 8739 and Streptococcus mutans OMZ 65 on contact with respect to controls

  15. Characterization of a silver-incorporated calcium phosphate film by RBS and its antimicrobial effects

    Energy Technology Data Exchange (ETDEWEB)

    Han, I-H [Institute of Physics and Applied Physics, and Atomic-Scale Surface Science Research Center, Yonsei University, Seou1 120-749 (Korea, Republic of); Lee, I-S [Institute of Physics and Applied Physics, and Atomic-Scale Surface Science Research Center, Yonsei University, Seou1 120-749 (Korea, Republic of); Song, J-H [Advanced Analysis Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Lee, M-H [Department of Medical Engineering, Yonsei University, Seoul 120-752 (Korea, Republic of); Park, J-C [Department of Medical Engineering, Yonsei University, Seoul 120-752 (Korea, Republic of); Lee, G-H [Korea Institute of Machinery and Materials, Chang-Won 641-010 (Korea, Republic of); Sun, X-D [Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Chung, S-M [Implantium Research Center, Seoul 135-879 (Korea, Republic of)

    2007-09-15

    A thin calcium phosphate film was synthesized on both commercially pure Ti and Si wafers by electron beam evaporation of hydroxyapatite as an evaporant with simultaneous Ar ion beam bombardments. Silver was introduced into an ion-beam-assisted deposition of a calcium phosphate thin film for antimicrobial effect. The amount of incorporated silver ions was controlled by immersing calcium-phosphate-coated samples in different AgNO{sub 3} concentrations, and Rutherford backscattering spectrometry (RBS) was employed to measure the amounts of substituted silver. The higher concentration of silver in the calcium phosphate film was more effective in reducing the bacteria of Escherichia coli ATCC 8739 and Streptococcus mutans OMZ 65 on contact with respect to controls.

  16. Reflections on the Mechanism of Calcium Phosphate Nucleation on Titanium in Simulated Body Fluids

    Institute of Scientific and Technical Information of China (English)

    F. T. Cheng

    2005-01-01

    The results and main findings of studies reported in the literature in relation to the deposition of calcium phosphate on Ti in simulated body fluids are summarized. The effects of the surface hydroxyl groups and the sign of surface charge on the nucleation of calcium phosphate are reviewed. One major controversy among the conclusions of different studies is the order of adsorption of the calcium ions and the phosphate ions in the initial stage of immersion. A simple model based on the amphoteric nature of the hydroxyl groups on Ti is proposed in an attempt to delineate the nucleation process for calcium phosphate on Ti in simulated body fluids. HPO42- ions interact with the hydroxyl groups via ion exchange and/or electrostatic attraction, and Ca2+ ions, via electrostatic attraction only. There is no preferential order of adsorption. Seemingly inconsistent results in different studies possibly arise from different prior treatments of the samples, which affect the adsorption properties.

  17. Cytotoxicity and genotoxicity of calcium silicate-based cements on an osteoblast lineage

    Directory of Open Access Journals (Sweden)

    Ana Lívia GOMES-CORNÉLIO

    2016-01-01

    Full Text Available Abstract Several calcium silicate-based biomaterials have been developed in recent years, in addition to Mineral Trioxide Aggregate (MTA. The aim of this study was to evaluate the cytotoxicity, genotoxicity and apoptosis/necrosis in human osteoblast cells (SAOS-2 of pure calcium silicate-based cements (CSC and modified formulations: modified calcium silicate-based cements (CSCM and three resin-based calcium silicate cements (CSCR1 (CSCR 2 (CSCR3. The following tests were performed after 24 hours of cement extract exposure: methyl-thiazolyl tetrazolium (MTT, apoptosis/necrosis assay and comet assay. The negative control (CT- was performed with untreated cells, and the positive control (CT+ used hydrogen peroxide. The data for MTT and apoptosis were submitted to analysis of variance and Bonferroni’s posttest (p < 0.05, and the data for the comet assay analysis, to the Kruskal-Wallis and Dunn tests (p < 0.05. The MTT test showed no significant difference among the materials in 2 mg/mL and 10 mg/mL concentrations. CSCR3 showed lower cell viability at 10 mg/mL. Only CSC showed lower cell viability at 50 mg/mL. CSCR1, CSCR2 and CSCR3 showed a higher percentage of initial apoptosis than the control in the apoptosis test, after 24 hours exposure. The same cements showed no genotoxicity in the concentration of 2 mg/mL, with the comet assay. CSC and CSCR2 were also not genotoxic at 10 mg/mL. All experimental materials showed viability with MTT. CSC and CSCR2 presented a better response to apoptosis and genotoxicity evaluation in the 10 mg/mL concentration, and demonstrated a considerable potential for use as reparative materials.

  18. Cytotoxicity assessment of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) paste

    OpenAIRE

    Sandra Kalil Bussadori; Elaine Marcilio Santos; Carolina Cardoso Guedes; Lara Jansiski Motta; Kristianne Porta Santos Fernandes; Raquel Agnelli Mesquita-Ferrari; Laura Hermida Bruno; Diana Ram

    2010-01-01

    Introduction: Casein phosphopeptides (CPP) have been shown to be good carriers of calcium, phosphate, and hydroxide ions to promote enamel remineralization with applications in oral care products, professional dental products, and food products. Objectives: Evaluate the cytotoxicity of a casein phosphopeptideamorphous calcium phosphate (CPP-ACP) paste in rat fibroblasts. Materials and methods: Cytotoxicity was measured by the Trypan blue dye exclusion assay and the MTT assay. Results: Long te...

  19. Comparison of Calcium Phosphate and Zinc Oxide Nanoparticles as Dermal Penetration Enhancers for Albumin

    OpenAIRE

    Shokri, Narges; Javar, H. A.

    2015-01-01

    Dermal drug delivery is highly preferred by patients due to its several advantages. Protein therapeutics have attracted huge attention recently. Since dermal delivery of proteins encounter problems, in this investigation, zinc oxide nanoparticles and calcium phosphate nanoparticles were compared as enhancers for dermal permeation of albumin. Albumin was applied simultaneously with zinc oxide nanoparticles or calcium phosphate nanoparticles on pieces of mouse skin. Skin permeation of albumin o...

  20. Influence of Ethylene Glycol on the Formation of Calcium Phosphate Nanocrystals

    Institute of Scientific and Technical Information of China (English)

    Yi ZUO; Yubao LI; Jie WEI; Yonggang YAN

    2003-01-01

    A synthesis route of using calcium hydroxide Ca(OH)2 with ethylene glycol solvent and orthophosphoric acid (H3PO4)as reagents is described. Three ratios of ethylene glycol to distilled water 1:0, 1:1 and 0:1 are used as diluting media for Ca(OH)2. Crystals of different morphology and composition are formed under weak alkaline circumstance at pH 7.0~8.0. Acicular calcium phosphate nanocrystals are prepared in pure ethylene glycol while rod-like calcium phosphate nanocrystals form in pure distilled water. The nanograde size of the former is smaller than that of the latter. Calcium-deficient apatite (CDAP) is obtained with a Ca/P molar ratio of 1.66. Therefore, it was deduced that the usage of ethylene glycol solvent could influence the formation of calcium phosphate crystal lattice.

  1. Authigenic dolomite cementation in the Upper Cretaceous Phosphate Formation, Western Desert, Egypt

    Science.gov (United States)

    Rifai, Rifai I.; Shaaban, Mohamad N.

    2007-12-01

    The Upper Cretaceous Phosphate Formation in the Western Desert of Egypt displays a characteristic facies association that includes marine phosphorites interbedded with black shales and glauconitic sandstones. The upper part of the formation is characterized by the presence of thin phosphatic beds, which are filled-extensively-with disordered and non stoichiometric (mean MgCO 3 = 41.4 ± 0.34 mol%) authigenic dolomite cement. SEM and the back scattered images of these coarse crystalline dolomite cements reveal that they display planar euhedral crystal boundaries, polymodal crystal size distribution and variable inclusion pattern. The relatively low and wide ranged δ18O (- 0.87 to - 4.15‰ VPDB) values of the dolomite cements coupled with their depleted Sr (mean = 187 ± 26 ppm) and high iron and manganese values (mean = 6851 ± 554 ppm and 11599 ± 229 ppm respectively) invoke that they were formed from mixed hypo-saline fluids within a mixing marine-meteoric zone probably during a low stand period at the vicinity of the Maastrichtian/Early Tertiary unconformity. Meanwhile, their negative δ13C (- 1.31 to - 3.56‰ VPDB) values argue for a possible involvement of isotopically light carbon, derived from degradation of organic matter, during their precipitation.

  2. RBS and XPS analyses of the composite calcium phosphate coatings for biomedical applications

    International Nuclear Information System (INIS)

    The calcium phosphate coatings on metallic implants are widely used for biomedical applications. The calcium phosphate coatings require mechanical strength, strong adhesion to the metallic implants, chemical stability and low dissolution into the human body fluid for stable functioning in the corrosive environment of the human body. In this study, a novel approach for improving the calcium phosphate coatings is utilized by adding trace metallic element into the coatings. We focused on teeth enamel, which is the hardest calcium phosphate tissue in the human body. Zn concentration increases exponentially from the interior to the surface of the enamel. As the Zn concentration increases, so the local hardness increases. Our previous studies suggest that Zn has influence on the hardness and other properties of enamel, calcium phosphate tissue. Calcium phosphate coatings doped with Zn was fabricated and characterized. The atomic composition and chemical state were investigated by using Rutherford backscattering spectroscopy (RBS) and X-ray photoelectron spectrometer (XPS), respectively. Scratch test was also carried out for measuring the adhesion of the coatings

  3. Clogging and Cementation Caused by Calcium or Iron Biogrouts

    Science.gov (United States)

    Ivanov, V.; Chu, J.; Naeimi, M.

    2012-12-01

    Chemical grouts are often used to reduce the hydraulic conductivity of soil for seepage control purposes. However, chemical grouts can be expensive and environmentally unfriendly. Therefore, two new biogrouts were tested for their bioclogging and biocementation properties. The first was calcium-based biogrout, which contained urease-producing bacteria, calcium chloride and urea for the crystallization of calcite due to enzymatic hydrolysis of urea. The second was iron-based biogrout, which consisted of urease-producing bacteria, ferric chelate, and urea for the precipitation of ferric hydroxide and carbonate due to enzymatic hydrolysis of urea. The permeability of sand (P, 10^-5 m/s), treated with calcium-based biogrout, linearly decreased as a function of the content of precipitated calcium (C, % w/w) according to the following equation: P = 5.1 - 4.0 C. Meanwhile, the permeability of sand treated with iron-based biogrout dropped to 2.7x10^-6 m/s at content of precipitated iron (F, % w/w) about 0.35 % w/w , by the equation: P = 5.1 - 14.6 F , and then slowly decreased to 1.4x10^-7 m/s at content of precipitated iron 1.8% w/w by the following equation: P = 0.36 - 0.23F. Both biogrouts have approximately same efficiency in the reduction of permeability of sand to low values. However, the mechanisms of bioclogging are probably different because the reduction of permeability by calcium-based biogrout was described by linear function of precipitated calcium but the reduction of permeability by iron-based biogrout showed two steps of the clogging. Different functions and mechanisms were related probably to the different type of precipitates. The images of biogrouted sand samples show that calcium-based biogrout produced white amorphous or crystallised calcium carbonate, while iron-based biogrout produced gel-like brown precipitate without visible crystals. The unconfined compressive strengths of the sand treated with different biogrouts (Y, kPa) increased by power

  4. Continuous monitoring of the zinc-phosphate acid-base cement setting reaction by proton nuclear magnetic relaxation

    Science.gov (United States)

    Apih, T.; Lebar, A.; Pawlig, O.; Trettin, R.

    2001-06-01

    Proton nuclear magnetic relaxation is a well-established technique for continuous and non destructive monitoring of hydration of conventional Portland building cements. Here, we demonstrate the feasibility of nuclear magnetic resonance (NMR) monitoring of the setting reaction of zinc-phosphate acid-base dental cements, which harden in minutes as compared to days, as in the case of Portland cements. We compare the setting of cement powder (mainly, zinc oxide) prepared with clinically used aluminum-modified orthophosphoric acid solution with the setting of a model system where cement powder is mixed with pure orthophosphoric acid solution. In contrast to previously published NMR studies of setting Portland cements, where a decrease of spin-lattice relaxation time is attributed to enhanced relaxation at the growing internal surface, spin-lattice relaxation time T1 increases during the set of clinically used zinc-phosphate cement. Comparison of these results with a detailed study of diffusion, viscosity, and magnetic-field dispersion of T1 in pure and aluminum-modified orthophosphoric acid demonstrates that the increase of T1 in the setting cement is connected with the increase of molecular mobility in the residual phosphoric acid solution. Although not taken into account so far, such effects may also significantly influence the relaxation times in setting Portland cements, particularly when admixtures with an effect on water viscosity are used.

  5. Continuous monitoring of the zinc-phosphate acid-base cement setting reaction by proton nuclear magnetic relaxation

    International Nuclear Information System (INIS)

    Proton nuclear magnetic relaxation is a well-established technique for continuous and non destructive monitoring of hydration of conventional Portland building cements. Here, we demonstrate the feasibility of nuclear magnetic resonance (NMR) monitoring of the setting reaction of zinc-phosphate acid-base dental cements, which harden in minutes as compared to days, as in the case of Portland cements. We compare the setting of cement powder (mainly, zinc oxide) prepared with clinically used aluminum-modified orthophosphoric acid solution with the setting of a model system where cement powder is mixed with pure orthophosphoric acid solution. In contrast to previously published NMR studies of setting Portland cements, where a decrease of spin-lattice relaxation time is attributed to enhanced relaxation at the growing internal surface, spin-lattice relaxation time T1 increases during the set of clinically used zinc-phosphate cement. Comparison of these results with a detailed study of diffusion, viscosity, and magnetic-field dispersion of T1 in pure and aluminum-modified orthophosphoric acid demonstrates that the increase of T1 in the setting cement is connected with the increase of molecular mobility in the residual phosphoric acid solution. Although not taken into account so far, such effects may also significantly influence the relaxation times in setting Portland cements, particularly when admixtures with an effect on water viscosity are used. [copyright] 2001 American Institute of Physics

  6. Effects of calcium phosphate/chitosan composite on bone healing in rats: calcium phosphate induces osteon formation.

    Science.gov (United States)

    Fernández, Tulio; Olave, Gilberto; Valencia, Carlos H; Arce, Sandra; Quinn, Julian M W; Thouas, George A; Chen, Qi-Zhi

    2014-07-01

    Vascularization of an artificial graft represents one of the most significant challenges facing the field of bone tissue engineering. Over the past decade, strategies to vascularize artificial scaffolds have been intensively evaluated using osteoinductive calcium phosphate (CaP) biomaterials in animal models. In this work, we observed that CaP-based biomaterials implanted into rat calvarial defects showed remarkably accelerated formation and mineralization of new woven bone in defects in the initial stages, at a rate of ∼60 μm/day (0.8 mg/day), which was considerably higher than normal bone growth rates (several μm/day, 0.1 mg/day) in implant-free controls of the same age. Surprisingly, we also observed histological evidence of primary osteon formation, indicated by blood vessels in early-region fibrous tissue, which was encapsulated by lamellar osteocyte structures. These were later fully replaced by compact bone, indicating complete regeneration of calvarial bone. Thus, the CaP biomaterial used here is not only osteoinductive, but vasculogenic, and it may have contributed to the bone regeneration, despite an absence of osteons in normal rat calvaria. Further investigation will involve how this strategy can regulate formation of vascularized cortical bone such as by control of degradation rate, and use of models of long, dense bones, to more closely approximate repair of human cortical bone. PMID:24460696

  7. Influence of whole-body irradiation on calcium and phosphate homeostasis in the rat

    International Nuclear Information System (INIS)

    Previous irradiation studies have revealed marked alterations in calcium metabolism. Moreover, the maintenance of calcium homeostasis with parathyroid hormone or calcium salts has been reported to reduce radiation lethality. Therefore, the present study was designed to evaluate the influence of irradiation on calcium homeostasis in the rat. Nine hundred rad of whole-body irradiation produced a significant depression of both plasma calcium and phosphate at 4 days postirradiation. This effect of irradiation was observed to be dose-dependent over a range of 600 to 1200 rad, and possibly related to irradiation-induced anorexia. The physiological significance of these observations is discussed

  8. Cytotoxicity Comparison of Harvard Zinc Phosphate Cement Versus Panavia F2 and Rely X Plus Resin Cements on Rat L929-fibroblasts

    Directory of Open Access Journals (Sweden)

    Alireza Akbar-zadeh Baghban

    2011-01-01

    Full Text Available Objective: Resin cements, regardless of their biocompatibility, have been widely used inrestorative dentistry during the recent years. These cements contain hydroxy ethyl methacrylate(HEMA molecules which are claimed to penetrate into dentinal tubules and mayaffect dental pulp. Since tooth preparation for metal ceramic restorations involves a largesurface of the tooth, cytotoxicity of these cements would be more important in fixed prosthodontictreatments. The purpose of this study was to compare the cytotoxicity of tworesin cements (Panavia F2 and Rely X Plus versus zinc phosphate cement (Harvardusing rat L929-fibroblasts in vitro.Materials and Methods: In this experimental study, ninety hollow glass cylinders (internaldiameter 5-mm, height 2-mm were made and divided into three groups. Each group wasfilled with one of three experimental cements; Harvard Zinc Phosphate cement, PanaviaF2 resin cement and Rely X Plus resin cement. L929- Fibroblast were passaged and subsequentlycultured in 6-well plates of 5×105 cells each. The culture medium was RPMI_1640. All samples were incubated in CO2. Using enzyme-linked immune-sorbent assay(ELISA and (3-(4,5-dimethylthiazol-2-yl-2, 5-diphenyltetrazolium bromide (MTT assay,the cytotoxicity of the cements was investigated at 1 hour, 24 hours and one week post exposure.Statistical analyses were performed via two-way ANOVA and honestly significantdifference (HSD Tukey tests.Results: This study revealed significant differences between the three cements at the differenttime intervals. Harvard cement displayed the greatest cytotoxicity at all three intervals.After 1 hour Panavia F2 showed the next greatest cytotoxicity, but after 24-hours and oneweekintervals Rely X Plus showed the next greatest cytotoxicity. The results further showedthat cytotoxicity decreased significantly in the Panavia F2 group with time (p<0.005, cytotoxicityincreased significantly in the Rely X Plus group with time (p<0.001, and the

  9. Preparation and bioactivity of micro-arc oxidized calcium phosphate coatings

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Y.K. [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Shandong University, Ji' nan, Shandong 250061 (China); School of Materials Science and Engineering, Shandong University, Ji' nan, Shandong 250061 (China); Chen, C.Z., E-mail: czchen@sdu.edu.cn [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Shandong University, Ji' nan, Shandong 250061 (China); School of Materials Science and Engineering, Shandong University, Ji' nan, Shandong 250061 (China); Wang, D.G.; Lin, Z.Q. [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Shandong University, Ji' nan, Shandong 250061 (China); School of Materials Science and Engineering, Shandong University, Ji' nan, Shandong 250061 (China)

    2013-09-16

    Calcium phosphate (CaP) coatings were prepared on ZK60 magnesium alloy by micro-arc oxidation (MAO) in electrolyte containing calcium acetate monohydrate (CH{sub 3}COO){sub 2}Ca·H{sub 2}O) and disodium hydrogen phosphate dodecahydrate (Na{sub 2}HPO{sub 4}·12H{sub 2}O). Scanning electron microscope (SEM), energy-dispersive X-ray spectrometry (EDX) and X-ray diffractometer (XRD) were employed to characterize the microstructure, elemental distribution and phase composition of the CaP coatings respectively. Simulated body fluid (SBF) immersion test was used to evaluate the coating degradability and bioactivity. After 30 days of SBF immersion, the CaP coatings effectively reduce the degradation rate. The surfaces of CaP coatings are covered by a new layer formed of numerous needle-like, spherical and columned calcium phosphates. SEM, EDX and XRD results suggest that these calcium phosphates are bioactive calcium phosphate phases such as hydroxyapatite (Ca{sub 10}(PO{sub 4}){sub 6}(OH){sub 2}, HA) and calcium pyrophosphates (Ca{sub 2}P{sub 2}O{sub 7}, CPP). The formation of these calcium phosphates indicates that the CaP coatings have bioactivity. - Highlights: • Bioactive CaP coatings are successfully formed on ZK60 magnesium alloy. • CaP coatings consist of MgO, MgF{sub 2}, CaO, CaF{sub 2} and Ca{sub 3}(PO{sub 4}){sub 2}. • Needle-like, spherical and columned calcium phosphates formed in SBF. • CaP coatings exhibit bioactivity and low corrosion rate.

  10. Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone

    DEFF Research Database (Denmark)

    Moesgaard, Mette; Poulsen, S.L.; Herfort, D.;

    2012-01-01

    represents a potential alternative to traditional SCMs, used for reduction of the CO2 emission associated with cement production. It is found that the NCAS glass takes part in the hydration reactions after about two weeks of hydration and a degree of reaction of approx. 50 % is observed after 90 days of......This work investigates the hydration of blended Portland cement containing 30 wt.% Na2O-CaO-Al2O3-SiO2 (NCAS) glass particles either as the only supplementary cementitious material (SCM) or in combination with limestone, using 29Si MAS NMR, powder XRD, and thermal analyses. The NCAS glass...... hydration. The hydrated glass contributes to the formation of the calcium-silicate-hydrate (C-S-H) phase, consuming a part of the Portlandite (Ca(OH)2) formed during hydration of the Portland cement. Furthermore, the presence of the glass and limestone particles, alone or in combination, results in an...

  11. Conditioning highly concentrated borate solutions with calcium sulfo-aluminate cement

    International Nuclear Information System (INIS)

    The early age hydration by borate solution of 3 calcium sulfo-aluminate cements (CSA), containing respectively 0%, 10% and 20% of gypsum by weight of cement was studied using isothermal calorimetry and dynamic mode rheo-metry. XRD and TGA analysis were carried out on pastes with increasing hydration degrees (up to 90 days) to specify the mineralogy and to figure out the mechanisms of borate immobilisation. It has been shown that the retarding effect of borate anions is due to the precipitation of the amorphous calcium borate C2B3H8; borate anions were then incorporated in Aft-type phases. The macroscopic properties of hydrated binders (compressive strength, length change) were also followed during 180 days. It appears that the mechanical strength continuously increases with the hydration degree. Length changes under wet-curing and sealed bag remain moderate and seem to be stabilized after 180 days

  12. Understanding the Biocompatibility of Sintered Calcium Phosphate with Ratio of [Ca]/[P] = 1.50

    OpenAIRE

    Feng-Lin Yen; Wei-Jen Shih; Min-Hsiung Hon; Hui-Ting Chen; I-Ming Hung; Homg-Huey Ko; Moo-Chin Wang

    2012-01-01

    Biocompatibility of sintered calcium phosphate pellets with [Ca]/[P] = 1.50 was determined in this study. Calcium pyrophosphate (CPP) phase formed on the sintered pellets immersed in a normal saline solution for 14 d at 37∘C. The intensities of hydroxyapatite (HA) reflections in the X-ray diffraction (XRD) patterns of the pellets were retrieved to as-sintered state. The pellet surface morphology shows that CPP crystallites were clearly present and make an amorphous calcium phosphate (ACP) to ...

  13. Microanalyses of the hydroxyl—poly—calcium sodium phosphate coatings produced by ion beam assisted deposition

    Institute of Scientific and Technical Information of China (English)

    LIUZhong-Yang; WANGChang-Xing; 等

    2002-01-01

    Thin calcium phosphate catings on titanium alloy substrates were prepared by Ar+ ion beam assisted deposition(IBAD) from hydroxyl-poly-calcium sodium phosphate(HPPA) target.The coatings were analyzed by XRD,FTIR,XPS,These analyses revealed that the as-deposited films were amorphous or no apparent crystallinity.No distinct absorption band of the hydroxyl group was observed in FTIR spectra of the coatings but new absorption bands were presented for CO3-2,The calcium to phosphorous ratio of these catings in different IBAD conditions varied from 0.46 to 3.36.

  14. Evaluation of pH, calcium ion release and antimicrobial activity of a new calcium aluminate cement

    Directory of Open Access Journals (Sweden)

    Fernanda de Carvalho Panzeri Pires-de-Souza

    2013-07-01

    Full Text Available This study evaluated the pH, calcium ion release and antimicrobial activity of EndoBinder (EB, containing different radiopacifiers: bismuth oxide (Bi2O3, zinc oxide (ZnO or zirconium oxide (ZrO2, in comparison to MTA. For pH and calcium ion release tests, 5 specimens per group (n = 5 were immersed into 10 mL of distilled and deionized water at 37°C. After 2, 4, 12, 24, 48 h; 7, 14 and 28 days, the pH was measured and calcium ion release quantified in an atomic absorption spectrophotometer. For antimicrobial activity, the cements were tested against S. aureus, E. coli, E. faecalis and C. albicans, in triplicate. MTA presented higher values for pH and calcium ion release than the other groups, however, with no statistically significant difference after 28 days (p > 0.05; and the largest inhibition halos for all strains, with no significant difference (E. coli and E. faecalis for pure EB and EB + Bi2O3 (p > 0.05. EB presented similar performance to that of MTA as regards pH and calcium ion release; however, when ZnO and ZrO2 were used, EB did not present antimicrobial activity against some strains.

  15. Biomechanics study of a composite injectable calcium phosphate bone cement in repairing tibial plateau compressive fractures%复合型可注射磷酸钙骨水泥在胫骨平台塌陷骨折修复中的生物力学研究

    Institute of Scientific and Technical Information of China (English)

    邹华章; 马晓春; 李创; 唐程; 龙浩; 叶建东

    2013-01-01

    目的 探讨一种复合聚乳酸-羟基乙酸共聚物的新型可注射磷酸钙骨水泥(CPC)结合双螺钉固定在胫骨平台SchatzkerⅡ型骨折模型修复中的生物力学性能,为临床微创治疗提供力学依据.方法 取10对老年尸体胫骨近端标本制备成胫骨平台SchatzkerⅡ型骨折模型后成对匹配随机分配到实验组和对照组中,分别采用CPC加压注入和自体松质骨充填植骨结合双螺钉横排固定的方法植骨固定胫骨平台骨折.将标本在材料测试机上进行轴向垂直压缩,记录载荷-位移数据,测量2组标本的最大失效载荷和抗压刚度.结果 新型CPC室温下具有良好的可注射性,在胫骨平台塌陷下方骨缺损区充填充分,且材料在骨缺损区周围松质骨中进一步渗透、扩散.实验组胫骨干骺端平均骨密度为(0.639 ±0.081)g·cm-2,对照组为(0.668±0.083)g·cm-2,2组间差异无统计学意义(P>0.05).实验组最大失效载荷为(4 101-813)N,对照组最大失效载荷为(692±138)N,2组间比较差异有统计学意义(P<0.05).实验组轴向抗压刚度为(1 363±362)N·mm-1,对照组轴向抗压刚度为(223±54)N·mm-1,2组间比较差异有统计学意义(P<0.05).结论 在胫骨平台SchatzkerⅡ型骨折中采用新型复合CPC加压充填植骨结合双螺钉固定技术,能有效恢复胫骨平台的抗塌陷力学性能,是一种理想的植骨填充材料.%Objective To investigate the biomechanics of a novel injectable calcium phosphate cement( CPC) composited by polylactic-co-glycolic acid in repairing tibial plateau type Schatzker Ⅱ fracture combined with double-screw fixation, and provide the mechanical basis for the clinical minimally invasive treatment. Methods Ten matched pairs of proximal tibia specimens were taken from 10 elderly cadavers and then were prepared Schatzker Ⅱ tibial plateau fracture model. The matched 10 pairs specimens were randomly divided into experiment group which were fixed by using

  16. 冻干硬脑膜内骨形成蛋白-自固化磷酸钙复合移植修复骨缺损%Repairing bone defects using bone morphogenetic protein and calcium phosphate cement combined with freeze-dried dura mater

    Institute of Scientific and Technical Information of China (English)

    邹国耀; 吴恒烜

    2009-01-01

    背景:骨形成蛋白和自固化磷酸钙各自有着良好的成骨能力,冻干硬脑膜内骨形成蛋白和自固化磷酸钙复合移植存在优化成骨效能的可能性.目的:以冻干硬脑膜为膜材料,观察膜内充填材料骨形成蛋白复合自固化磷酸钙移植修复节段性骨缺损的效果.设计、时间及地点:随机分组设计,动物体内组织病理学对照观察,于2006-07/2007-07在广西医科大学动物实验室完成.对象:健康成年新西兰大白兔28只,雌雄不限,体质量1.5~2.5 kg.方法:实验兔28只,其中4只用于取硬脑膜.其余24只随机分成A,B两大组,每组12只.A组制造双侧兔桡骨中段10 mm的骨缺损.一侧骨缺损用骨形成蛋白、自固化磷酸钙、冻干硬脑膜复合移植修复,为骨形成蛋白组, 另一侧不予处理作为空白对照组.B组制造单侧兔桡骨中段10 mm的骨缺损,用骨髓、自固化磷酸钙、冻干硬脑膜复合移植修复称骨髓组.主要观察指标:于术后第1,2,4,6,8,10,12周分别行双侧桡骨X射线检查.观察骨缺损处的新骨形成及骨修复情况.并于术后第2,4,8,12周切取标本行组织学检查及成骨面积分析.结果:在术后第4,8,12周,骨形成蛋白组的成骨面积大于骨髓组(P<0.05),而在实验早期(术后2周)两组间差异无显著性意义(P>0.05);在实验的各个时期,骨形成蛋白组和骨髓组的成骨面积均明显大于空白组(P<0.01).X射线结果显示,骨形成蛋白组在10~12周出现明显骨痂塑形现象;组织学病理切片结果显示,骨形成蛋白组在12周时桡骨可见成熟骨髓,骨缺损处为成熟的板层骨连接.结论:骨形成蛋白复合自固化磷酸钙与冻干硬脑膜移植具有良好的成骨作用.%BACKGROUND: Both bone morphogenetic protein (BMP) and calcium phosphate cement (CPC) have excellent osteogenic capability, so, it is possible to optimize osteogenic efficiency by combing BMP, CPC and freeze-dried dura mater (FDDM

  17. Indirect pulp therapy in a symptomatic mature molar using calcium enriched mixture cement

    OpenAIRE

    Hassan Torabzadeh; Saeed Asgary

    2013-01-01

    Dental pulp has the ability of repair/regeneration. Indirect pulp therapy (IPT) is recommended for pulp preservation in asymptomatic teeth with extremely deep caries as well as teeth with clinical symptoms of reversible pulpitis. In this case study, we performed IPT with calcium enriched mixture (CEM) cement on a symptomatic permanent molar. After clinical/radiographic examinations the tooth was diagnosed with irreversible pulpitis and associated apical periodontitis. IPT involved partial car...

  18. Analysis of the color alteration and radiopacity promoted by bismuth oxide in calcium silicate cement

    Directory of Open Access Journals (Sweden)

    Marina Angelica Marciano

    2013-07-01

    Full Text Available The aim of the study was to determine if the increase in radiopacity provided by bismuth oxide is related to the color alteration of calcium silicate-based cement. Calcium silicate cement (CSC was mixed with 0%, 15%, 20%, 30% and 50% of bismuth oxide (BO, determined by weight. Mineral trioxide aggregate (MTA was the control group. The radiopacity test was performed according to ISO 6876/2001. The color was evaluated using the CIE system. The assessments were performed after 24 hours, 7 and 30 days of setting time, using a spectrophotometer to obtain the ΔE, Δa, Δb and ΔL values. The statistical analyses were performed using the Kruskal-Wallis/Dunn and ANOVA/Tukey tests (p 3 mm equivalent of Al. The MTA group was statistically similar to the CSC / 30% BO group (p > 0.05. In regard to color, the increase of bismuth oxide resulted in a decrease in the ΔE value of the calcium silicate cement. The CSC group presented statistically higher ΔE values than the CSC / 50% BO group (p < 0.05. The comparison between 24 hours and 7 days showed higher ΔE for the MTA group, with statistical differences for the CSC / 15% BO and CSC / 50% BO groups (p < 0.05. After 30 days, CSC showed statistically higher ΔE values than CSC / 30% BO and CSC / 50% BO (p < 0.05. In conclusion, the increase in radiopacity provided by bismuth oxide has no relation to the color alteration of calcium silicate-based cements.

  19. Investigation of Phosphate Cement-based Binder with Super High Early Strength for Repair of Concrete

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Magnesium phosphate cement-based binder (MPB) for repair of concrete was prepared by proportionally mixing over burned MgO powder (M) with NHH2PO4 powder (P) and set modifying admixtures. It is characteristic by excellent properties such as rapid setting,high strength and high bond strength to old concrete.. The study is focused on the key factors influencing the setting time and strength of MPB, the bond property of MPB to old concrete and the kinetic feature of the hydration of MPB.

  20. Effect of Incorporating Nanoporous Metal Phosphate Materials on the Compressive Strength of Portland Cement

    OpenAIRE

    Wellman, Dawn M.; Kent E. Parker; Mattigod, Shas V.; Fryxell, Glen E.

    2008-01-01

    Nanoporous metal phosphate (NP-MPO) materials are being developed for removal of contaminant oxyanions (As(OH)O32−, CrO42−, and TcO4−), and cations (mercury, cadmium, and lead) from water and waste streams. Following sequestration, incorporation of metal laden NP-MPOs as a portion of cement formulation would provide an efficient and low-cost way to immobilize metal laden NP-MPOs in an easily handled waste form suitable for permanent disposal. There are no known investigations...

  1. Immobilization of calcium and phosphate ions improves the osteoconductivity of titanium implants.

    Science.gov (United States)

    Sunarso; Toita, Riki; Tsuru, Kanji; Ishikawa, Kunio

    2016-11-01

    In this work, to elevate weak osteoconductivity of titanium (Ti) implant, we prepared a Ti implant having both calcium and phosphate ions on its surface. To modify calcium and phosphate ions onto Ti, phosphate ions were first immobilized by treating the Ti with a NaH2PO4 solution, followed by CaCl2 treatment to immobilize calcium ions, which created the calcium and phosphate ions-modified Ti (Ca-P-Ti). X-ray photoelectron spectroscopy and thin-layer X-ray diffraction measurement confirmed that both phosphate and calcium ions were co-immobilized onto the Ti surface on the molecular level. Three-hour after seeding MC3T3-E1 murine pre-osteoblast cells on substrates, cell number on Ca-P-Ti was much larger than that of Ti and phosphate-modified Ti (P-Ti), but was similar to that of calcium-modified Ti (Ca-Ti). Also, MC3T3-E1 cells on Ca-P-Ti expressed larger amount of vinculin, a focal adhesion protein, than those on other substrates, probably resulting in larger cell size as well as greater cell proliferation on Ca-P-Ti than those on other substrates. Alkaline phosphatase activity of cells on Ca-P-Ti was greater than those on Ti and P-Ti, but was almost comparable to that of Ca-Ti. Moreover, the largest amount of bone-like nodule formation was observed on Ca-P-Ti. These results provide evidence that calcium and phosphate ions-co-immobilization onto Ti increased the osteoconductivity of Ti by stimulating the responses of pre-osteoblast cells. This simple modification would be promising technique for bone tissue implant including dental and orthopedic implants. PMID:27524023

  2. Discrimination between biologically relevant calcium phosphate phases by surface-analytical techniques

    International Nuclear Information System (INIS)

    The spatially resolved phase identification of biologically relevant calcium phosphate phases (CPPs) in bone tissue is essential for the elucidation of bone remodeling mechanisms and for the diagnosis of bone diseases. Analytical methods with high spatial resolution for the discrimination between chemically quite close phases are rare. Therefore the applicability of state-of-the-art ToF-SIMS, XPS and EDX as chemically specific techniques was investigated. The eight CPPs hydroxyapatite (HAP), β-tricalcium phosphate (β-TCP), α-tricalcium phosphate (α-TCP), octacalcium phosphate (OCP), dicalcium phosphate dihydrate (DCPD), dicalcium phosphate (DCP), monocalcium phosphate (MCP) and amorphous calcium phosphate (ACP) were either commercial materials in high purity or synthesized by ourselves. The phase purity was proven by XRD analysis. All of the eight CPPs show different mass spectra and the phases can be discriminated by applying the principal component analysis method to the mass spectrometric data. The Ca/P ratios of all phosphates were determined by XPS and EDX. With both methods some CPPs can be distinguished, but the obtained Ca/P ratios deviate systematically from their theoretical values. It is necessary in any case to determine a calibration curve, respectively the ZAF values, from appropriate standards. In XPS also the O(1s)-satellite signals are correlated to the CPPs composition. Angle resolved and long-term XPS measurements of HAP clearly prove that there is no phosphate excess at the surface. Decomposition due to X-ray irradiation has not been observed.

  3. Discrimination between biologically relevant calcium phosphate phases by surface-analytical techniques

    Energy Technology Data Exchange (ETDEWEB)

    Kleine-Boymann, Matthias, E-mail: matthias.kleine-boymann@phys.chemie.uni-giessen.de; Rohnke, Marcus, E-mail: marcus.rohnke@phys.chemie.uni-giessen.de; Henss, Anja, E-mail: anja.henss@phys.chemie.uni-giessen.de; Peppler, Klaus, E-mail: klaus.peppler@phys.chemie.uni-giessen.de; Sann, Joachim, E-mail: joachim.sann@phys.chemie.uni-giessen.de; Janek, Juergen, E-mail: juergen.janek@phys.chemie.uni-giessen.de

    2014-08-01

    The spatially resolved phase identification of biologically relevant calcium phosphate phases (CPPs) in bone tissue is essential for the elucidation of bone remodeling mechanisms and for the diagnosis of bone diseases. Analytical methods with high spatial resolution for the discrimination between chemically quite close phases are rare. Therefore the applicability of state-of-the-art ToF-SIMS, XPS and EDX as chemically specific techniques was investigated. The eight CPPs hydroxyapatite (HAP), β-tricalcium phosphate (β-TCP), α-tricalcium phosphate (α-TCP), octacalcium phosphate (OCP), dicalcium phosphate dihydrate (DCPD), dicalcium phosphate (DCP), monocalcium phosphate (MCP) and amorphous calcium phosphate (ACP) were either commercial materials in high purity or synthesized by ourselves. The phase purity was proven by XRD analysis. All of the eight CPPs show different mass spectra and the phases can be discriminated by applying the principal component analysis method to the mass spectrometric data. The Ca/P ratios of all phosphates were determined by XPS and EDX. With both methods some CPPs can be distinguished, but the obtained Ca/P ratios deviate systematically from their theoretical values. It is necessary in any case to determine a calibration curve, respectively the ZAF values, from appropriate standards. In XPS also the O(1s)-satellite signals are correlated to the CPPs composition. Angle resolved and long-term XPS measurements of HAP clearly prove that there is no phosphate excess at the surface. Decomposition due to X-ray irradiation has not been observed.

  4. The role of casein phosphopeptide-amorphous calcium phosphate products in remineralization of incipient enamel lesions and its substantivity

    OpenAIRE

    Abhay Taranath; Deepika Pai; Kalyan Chakravarthy

    2014-01-01

    Objective: Milk derived calcium, phosphate and casein were known to be anti-cariogenic but in the modern era of early interception of caries the agents like casien phosphopeptide-amorphous calcium phosphate (CPP-ACP) derived from milk are known to also repair early lesions. This in vitro study was designed to evaluate the remineralizing potential of CPP-ACP and CPP-amorphous calcium phosphate fluoride (ACPF) on smooth surface carious lesions of the enamel and its substantivity following demin...

  5. Pathogenic role of basic calcium phosphate crystals in destructive arthropathies.

    Directory of Open Access Journals (Sweden)

    Hang-Korng Ea

    Full Text Available basic calcium phosphate (BCP crystals are commonly found in osteoarthritis (OA and are associated with cartilage destruction. BCP crystals induce in vitro catabolic responses with the production of metalloproteases and inflammatory cytokines such as interleukin-1 (IL-1. In vivo, IL-1 production induced by BCP crystals is both dependant and independent of NLRP3 inflammasome. We aimed to clarify 1/ the role of BCP crystals in cartilage destruction and 2/ the role of IL-1 and NLRP3 inflammasome in cartilage degradation related to BCP crystals.synovial membranes isolated from OA knees were analysed by alizarin Red and FTIR. Pyrogen free BCP crystals were injected into right knees of WT, NLRP3 -/-, ASC -/-, IL-1α -/- and IL-1β-/- mice and PBS was injected into left knees. To assess the role of IL-1, WT mice were treated by intra-peritoneal injections of anakinra, the IL-1Ra recombinant protein, or PBS. Articular destruction was studied at d4, d17 and d30 assessing synovial inflammation, proteoglycan loss and chondrocyte apoptosis. BCP crystals were frequently found in OA synovial membranes including low grade OA. BCP crystals injected into murine knee joints provoked synovial inflammation characterized by synovial macrophage infiltration that persisted at day 30, cartilage degradation as evidenced by loss of proteoglycan staining by Safranin-O and concomitant expression of VDIPEN epitopes, and increased chondrocyte apoptosis. BCP crystal-induced synovitis was totally independent of IL-1α and IL-1β signalling and no alterations of inflammation were observed in mice deficient for components of the NLRP3-inflammasome, IL-1α or IL-1β. Similarly, treatment with anakinra did not prevent BCP crystal effects. In vitro, BCP crystals elicited enhanced transcription of matrix degrading and pro-inflammatory genes in macrophages.intra-articular BCP crystals can elicit synovial inflammation and cartilage degradation suggesting that BCP crystals have a direct

  6. Effects of a discoloration-resistant calcium aluminosilicate cement on the viability and proliferation of undifferentiated human dental pulp stem cells

    OpenAIRE

    Li-na Niu; Devon Watson; Kyle Thames; Carolyn M. Primus; Bergeron, Brian E.; Kai Jiao; Bortoluzzi, Eduardo A.; Cutler, Christopher W.; Ji-hua Chen; PASHLEY David H.; Franklin R Tay

    2015-01-01

    Discoloration-resistant calcium aluminosilicate cement has been formulated to overcome the timely problem of tooth discoloration reported in the clinical application of bismuth oxide-containing hydraulic cements. The present study examined the effects of this experimental cement (Quick-Set2) on the viability and proliferation of human dental pulp stem cells (hDPSCs) by comparing the cellular responses with commercially available calcium silicate cement (white mineral trioxide aggregate; WMTA)...

  7. Templating route for mesostructured calcium phosphates with carboxylic acid- and amine-type surfactants.

    Science.gov (United States)

    Ikawa, Nobuaki; Hori, Hideki; Kimura, Tatsuo; Oumi, Yasunori; Sano, Tsuneji

    2008-11-18

    Mesostructured calcium phosphates constructed by ionic frameworks were synthesized using carboxylic acid- and amine-type surfactants in mixed solvent systems of ethanol and water. A lamellar mesostructured calcium phosphate was prepared using palmitic acid as an anionic surfactant, as in the case using n-alkylamines. A wormhole-like mesostructured calcium phosphate can be obtained using dicarboxyl N-lauroyl- l-glutamic acid, whose headgroup is larger than that of palmitic acid. Similar mesostructured product was obtained using 4-dodecyldiethylenetriamine with a large headgroup containing two primary amine groups. Interactions of carboxyl and primary amino groups in the surfactant molecules with inorganic species are quite important for the formation of mesostructured calcium phosphates. The Ca/P molar ratio of mesostructured calcium phosphates was strongly affected by the molecular structure of surfactants containing carboxyl and primary amino groups. Ca-rich materials can be obtained using carboxylic acid-type surfactants (Ca/P approximately 1.7) rather than amine-type surfactants (Ca/P approximately 1.0). PMID:18947246

  8. Comparison of three calcium phosphate bone graft substitutes from biomechanical, histological, and crystallographic perspectives using a rat posterolateral lumbar fusion model.

    Science.gov (United States)

    Hu, Ming-Hsien; Lee, Pei-Yuan; Chen, Wen-Cheng; Hu, Jin-Jia

    2014-12-01

    This study evaluated the effectiveness of three calcium phosphate bone graft substitutes with different chemical compositions on spinal fusion using a rat posterolateral lumbar fusion model. Specifically, two recently developed non-dispersive tetracalcium phosphate/dicalcium phosphate anhydrous-based calcium phosphate cements (CPCs), namely a CPC consisting of equimolar amounts of the two compounds (nd-CPC) and a CPC consisting of a two-fold greater amount of dicalcium phosphate anhydrous (DCP-rich CPC), were compared with a commercial calcium phosphate bone graft (c-CPG) consisting of hydroxyapatite (60%) and β-tricalcium phosphate (40%). Single-level posterolateral lumbar fusion was performed at the L4-L5 vertebrae in fifteen adult rats (n=5 for each group). Spinal fusion was evaluated with radiographs, manual palpation, mechanical testing, micro-CT, and histology 8 weeks post-surgery. In particular, the crystallographic phases in the three substitutes were identified before and 8 weeks after their implantation. Manual palpation revealed stable constructs in nearly all of the spine specimens. The stiffness and bending load of fused spines in the two CPC groups were comparable to those in the c-CPG group. The radiographs specifically revealed implant resorption and bone remodeling in the DCP-rich CPC group. Analysis of 3D micro-CT images revealed that the bone volume ratio in the DCP-rich CPC group was significantly greater than those in the nd-CPC and c-CPG groups. Histology showed that the DCP-rich CPC group exhibited the highest degree of bone regeneration and osseointegration. Notably, DCP-rich CPC led to a pronounced phase transformation, generating the greatest amount of poorly crystalline apatite among the three groups, which together with adequate resorption may explain the aforementioned positive findings. We therefore conclude that of the bone graft substitutes considered, DCP-rich CPC has the greatest potential to be used in spinal fusion. PMID

  9. Sorption behavior of Zn(II) ions on synthetic apatitic calcium phosphates

    Science.gov (United States)

    Sebei, Haroun; Pham Minh, Doan; Nzihou, Ange; Sharrock, Patrick

    2015-12-01

    The synthesis, characterization and the reactivity of apatitic calcium phosphates (Ca-HA, chemical formula Ca10(PO4)6(OH)2) is reported. Calcium carbonate (CaCO3) and potassium dihydrogen orthophosphate (KH2PO4) were selected as economical starting materials for the synthesis of Ca-HA under atmospheric conditions. Monocalcium phosphate monohydrate (MCPM), dicalcium phosphate dihydrate (DCPD), and octacalcium phosphate pentahydrate (OCP) were identified as the main intermediates of the synthesis reaction. The product obtained after 48 h of reaction contains mainly low-crystalline Ca-HA and small amounts of other calcium phosphates such as octacalcium phosphate (OCP), B-type carbonate apatite (CAP), as well as unreacted calcium carbonate. This Ca-HA was found to be active for the removal of Zn2+ from an aqueous solution. Its sorption capacity reached up to 120 mg of Zn2+ per g of Ca-HA powder after 24 h of reaction. The monitoring of soluble Zn, Ca and P during the sorption experiment allowed characterizing the mechanism of Zn uptake. Dissolution-precipitation, ionic exchange and surface complexation are the three main mechanisms involved in the sorption processes. The contribution of these mechanisms is discussed in detail.

  10. Study of the action of phosphate ions contained in the mixing water on the hydration of a Portland cement

    International Nuclear Information System (INIS)

    Cementation is considered as the most attractive solution for the conditioning of low and intermediate radioactive wastes. The species contained in these wastes can strongly influence the reactivity of the cement pastes, it is in particular the case of the ortho-phosphate ions which are found in the evaporation concentrates. The aim of our work was to determine the influence of these ions on the hydration and the rheological properties of the cement pastes at early age as well as the mechanical and physical properties on the hardened material. (author)

  11. Effect of calcium sulfates on the early hydration of calcium sulfoaluminate cement and the stability of embedded aluminium

    International Nuclear Information System (INIS)

    Conventional Portland cement-based systems have been considered unsuitable for immobilising nuclear wastes containing reactive metals, such as aluminium, due to the high pH of the pore solution (usually around 12.5) and free moisture. On the contrary, calcium sulfo-aluminate cement (CSA) produces a lower pH (10.5-12) environment and has an excellent water binding capability as a result of the formation of its main hydration product, ettringite. Therefore, it offers a good potential to immobilise aluminium. However, the pore solution pH and ettringite formation depend largely on the raw materials used to formulate the CSA, which is usually a blend of 75%-85% of CSA clinker and 15-25% of calcium sulfate (in the form of gypsum or anhydrite). In this paper, it was found that, compared to anhydrite, gypsum (15% wt of the blend) demonstrated the highest reduction in the corrosion of embedded Al, possibly due to its lower initial pH (around 10.5) and self-desiccating nature at the early stage of hydration. Whilst the CSA/anhydrite had a higher Al corrosion rate, the initial set was more acceptable than CSA/gypsum. Nonetheless, overall, it was concluded that CSA with gypsum (15% wt) should be considered as a base formulation for the encapsulation of Al waste. The unfavorable rapid set and high heat generation, however, demonstrated that modifications are required, potentially by using mineral additions. (authors)

  12. Calcium looping spent sorbent as a limestone replacement in the manufacture of portland and calcium sulfoaluminate cements.

    Science.gov (United States)

    Telesca, Antonio; Marroccoli, Milena; Tomasulo, Michele; Valenti, Gian Lorenzo; Dieter, Heiko; Montagnaro, Fabio

    2015-06-01

    The calcium looping (CaL) spent sorbent (i) can be a suitable limestone replacement in the production of both ordinary Portland cement (OPC) and calcium sulfoaluminate (CSA) cement, and (ii) promotes environmental benefits in terms of reduced CO2 emission, increased energy saving and larger utilization of industrial byproducts. A sample of CaL spent sorbent, purged from a 200 kWth pilot facility, was tested as a raw material for the synthesis of two series of OPC and CSA clinkers, obtained from mixes heated in a laboratory electric oven within temperature ranges 1350°-1500 °C and 1200°-1350 °C, respectively. As OPC clinker-generating mixtures, six clay-containing binary blends were investigated, three with limestone (reference mixes) and three with the CaL spent sorbent. All of them showed similar burnability indexes. Moreover, three CSA clinker-generating blends (termed RM, MA and MB) were explored. They included, in the order: (I) limestone, bauxite and gypsum (reference mix); (II) CaL spent sorbent, bauxite and gypsum; (III) CaL spent sorbent plus anodization mud and a mixture of fluidized bed combustion (FBC) fly and bottom ashes. The maximum conversion toward 4CaO·3Al2O3·SO3, the chief CSA clinker component, was the largest for MB and almost the same for RM and MA. PMID:25915150

  13. The Retentive Strength of Cemented Zirconium Oxide Crowns after Dentin Pretreatment with Desensitizing Paste Containing 8% Arginine and Calcium Carbonate.

    Science.gov (United States)

    Pilo, Raphael; Harel, Noga; Nissan, Joseph; Levartovsky, Shifra

    2016-01-01

    The effect of dentin pretreatment with Desensitizing Paste containing 8% arginine and calcium carbonate on the retention of zirconium oxide (Y-TZP) crowns was tested. Forty molar teeth were mounted and prepared using a standardized protocol. Y-TZP crowns were produced using computer-aided design and computer-aided manufacturing (CAD-CAM) technology. The 40 prepared teeth were either pretreated with Desensitizing Paste or not pretreated. After two weeks, each group was subdivided into two groups, cemented with either Resin Modified Glass Ionomer Cement (RMGIC) or Self Adhesive Resin Cement (SARC)). Prior to cementation, the surface areas of the prepared teeth were measured. After aging, the cemented crown-tooth assemblies were tested for retentive strength using a universal testing machine. The debonded surfaces of the teeth and crowns were examined microscopically at 10× magnification. Pretreating the dentin surfaces with Desensitizing Paste prior to cementation did not affect the retention of the Y-TZP crowns. The retentive values for RMGIC (3.04 ± 0.77 MPa) were significantly higher than those for SARC (2.28 ± 0.58 MPa). The predominant failure modes for the RMGIC and SARC were adhesive cement-dentin and adhesive cement-crown, respectively. An 8.0% arginine and calcium carbonate in-office desensitizing paste can be safely used to reduce post-cementation sensitivity without reducing the retentive strength of Y-TZP crowns. PMID:27023532

  14. The Retentive Strength of Cemented Zirconium Oxide Crowns after Dentin Pretreatment with Desensitizing Paste Containing 8% Arginine and Calcium Carbonate

    Directory of Open Access Journals (Sweden)

    Raphael Pilo

    2016-03-01

    Full Text Available The effect of dentin pretreatment with Desensitizing Paste containing 8% arginine and calcium carbonate on the retention of zirconium oxide (Y-TZP crowns was tested. Forty molar teeth were mounted and prepared using a standardized protocol. Y-TZP crowns were produced using computer-aided design and computer-aided manufacturing (CAD-CAM technology. The 40 prepared teeth were either pretreated with Desensitizing Paste or not pretreated. After two weeks, each group was subdivided into two groups, cemented with either Resin Modified Glass Ionomer Cement (RMGIC or Self Adhesive Resin Cement (SARC. Prior to cementation, the surface areas of the prepared teeth were measured. After aging, the cemented crown-tooth assemblies were tested for retentive strength using a universal testing machine. The debonded surfaces of the teeth and crowns were examined microscopically at 10× magnification. Pretreating the dentin surfaces with Desensitizing Paste prior to cementation did not affect the retention of the Y-TZP crowns. The retentive values for RMGIC (3.04 ± 0.77 MPa were significantly higher than those for SARC (2.28 ± 0.58 MPa. The predominant failure modes for the RMGIC and SARC were adhesive cement-dentin and adhesive cement-crown, respectively. An 8.0% arginine and calcium carbonate in-office desensitizing paste can be safely used to reduce post-cementation sensitivity without reducing the retentive strength of Y-TZP crowns.

  15. Calcium-enriched mixture cement as artificial apical barrier: A case series

    Directory of Open Access Journals (Sweden)

    Ali Nosrat

    2011-01-01

    Full Text Available In comparison to the conventional apexification using calcium hydroxide, artificial apical barrier technique is more valuable and less time consuming. This article describes successful use of calcium-enriched mixture (CEM cement as an artificial apical barrier in open apices. In this study, 13 single-rooted teeth with necrotic pulps and open apices were treated non-surgically. After copious irrigation of the root canals with NaOCl 5.25% and gentle filing, based on need for interappointment dressing, treatments were followed by CEM cement (BioniqueDent, Tehran, Iran apical plug insertion in the first or second appointment. All cases were then permanently restored. All subjects were followed until radiographic evidence of periradicular healing was seen (mean 14.5 months. Clinically, all cases were functional and asymptomatic and complete osseous healing was observed in all the teeth. Considering the biological properties of CEM cement, this new endodontic biomaterial might be appropriate to be used as artificial apical barrier in the open apex teeth.

  16. Effect of solute concentration on fibroin regulated biomineralization of calcium phosphate

    International Nuclear Information System (INIS)

    In this paper we used UV/Visible method to study the effect of solute concentration on fibroin regulated biomineralization of calcium phosphate. During the reaction process, ultraviolet-visible spectrophotometer was used to track the extinction in the reaction solution. It is found that kinetics of the biomineralization can be strongly affected by the presence of fibroin. Fibroin with higher concentration has more positive effect on the biomineralization process. Under the appropriate reaction conditions, wave crest and wave trough appear in the kinetic curves of fibroin biomineralization. The wave crest and wave trough phenomenon is mainly related with the process of phase separation. X-ray Diffraction (XRD) result shows the calcium phosphate before the wave trough is mainly amorphous calcium phosphate, while after the wave trough crystal of hydroxyapatite (HA) and brushite (DCPD) are the mainly ingredients

  17. Properties of Chemically Combusted Calcium Carbide Residue and Its Influence on Cement Properties

    Directory of Open Access Journals (Sweden)

    Hongfang Sun

    2015-02-01

    Full Text Available Calcium carbide residue (CCR is a waste by-product from acetylene gas production. The main component of CCR is Ca(OH2, which can react with siliceous materials through pozzolanic reactions, resulting in a product similar to those obtained from the cement hydration process. Thus, it is possible to use CCR as a substitute for Portland cement in concrete. In this research, we synthesized CCR and silica fume through a chemical combustion technique to produce a new reactive cementitious powder (RCP. The properties of paste and mortar in fresh and hardened states (setting time, shrinkage, and compressive strength with 5% cement replacement by RCP were evaluated. The hydration of RCP and OPC (Ordinary Portland Cement pastes was also examined through SEM (scanning electron microscope. Test results showed that in comparison to control OPC mix, the hydration products for the RCP mix took longer to formulate. The initial and final setting times were prolonged, while the drying shrinkage was significantly reduced. The compressive strength at the age of 45 days for RCP mortar mix was found to be higher than that of OPC mortar and OPC mortar with silica fume mix by 10% and 8%, respectively. Therefore, the synthesized RCP was proved to be a sustainable active cementitious powder for the strength enhanced of building materials, which will result in the diversion of significant quantities of this by-product from landfills.

  18. Investigation of fresh and hardened properties of Calcium sulfoaluminate (CSA cement blends

    Directory of Open Access Journals (Sweden)

    P. Herrmann

    2014-05-01

    Full Text Available Calcium sulfoaluminate (CSA is a comparatively new cementitious material that is mainly established in China where it is produced in a large scale. CSA cement is not covered by European standards. However, it provides different beneficial properties such as rapid hardening and high early strength development. Furthermore, the usage of CSA cement can save energy during production process in comparison to established cementitious materials. Therefore it is also more environmental friendly. Insufficient knowledge of this material behaviour restricts the possibilities and makes further research necessary. The research project applied a laboratory test program to elaborate the characterization of the materials. The obtained knowledge from these tests was then applied to further tests to determine application relevant key properties of CSA based pastes and mortars.The properties of pure CSA cement had been compared with the properties of CSA blends. The additions were PC, HAC, FA and GGBS with quantities of 10, 20 and 30%. The water to cement ratio was varying between 0.4, 0.5 and 0.6. General tests like fineness, XRD and XRF were used to define the present non-standardized material. Investigation of fresh pastes included measurement of setting time and calorimetry. Hardened mortar specimens of different ages were examined for compressive strength. The results showed that CSA itself hardens very rapidly and gives an early strength development. Possible ways of utilization of CSA based mortars and concretes were also emphasized in the paper.

  19. Ossification Vesicles with Calcium Phosphate in the Eyes of the Insect Copium teucrii (Hemiptera: Tingidae

    Directory of Open Access Journals (Sweden)

    Javier Garcia-Guinea

    2011-01-01

    Full Text Available Arthropod eyes are built of repeating units named ommatidia. Each single ommatidium unit contains a cluster of photoreceptor cells surrounded by support cells and pigment cells. The insect Copium eye ommatidia include additional calcium-phosphate deposits, not described in insects to date, which can be examined today using a combined set of modern microscopy and spectroscopy techniques. Teucrium gnaphalodes L'Her plants, growing in central Spain, develop galls induced by Copium insects. A survey of C. teucrii adult specimens resulted in surprising environmental scanning electron microscopy (ESEM images, showing that their bright red eyes contain a calcium-phosphate mineralization. A complete survey of Copium eye specimens was performed by ESEM using energy-dispersive spectroscopy, backscattered electron detector and cathodoluminescence (CL probes, field emission scanning electron microscopy, micro-Raman spectroscopy, and confocal laser scanning microscopy in order to learn ommatidia features, such as chemical composition, molecular structure, cell membrane, and internal ommatidium eye fluids and calcium-phosphate distribution deposits. The CL panchromatic images distinguish between the calcium-phosphate ommatidium and calcium-phosphate setae, which are more apatite rich. They show Raman bands attributable to bone tissue apatite biomaterials, such as bone, collagen, lipids, and blood, i.e., peptides, amide-S, amide-II, amide-III, and cytochrome P-450scc. The chemical composition of both galls and leaves of T. gnaphalodes was determined by gas chromatography – mass spectrometry (GC-MS of their extracts. The spectrometric and microscopic images reveal that the calcium-phosphate mineralization is formed and constrained to Copium ommatidia, which are both matrix vesicles generating mixtures of apatite collagen and operational compound eyes of the insect.

  20. Phosphate recovery using calcium zeolite in ultrafiltration pilot plant

    OpenAIRE

    La Rotonda Ferrer, Pablo

    2015-01-01

    One of the most important ecological problems is the eutrophication, this process consist in the uncontrolled growing of algae and phytoplankton, which can destroy entire aquatic ecosystems. The reason of this process is the excess of nutrients, as for example, phosphate coming from human activities. This project focus on the study of synthetic zeolites capacity to absorb phosphate from wastewater. Zeolites are porous minerals of the alumina-silicates family with high capacity ...

  1. In situ synchrotron X-ray powder diffraction study of the early hydration of α-tricalcium phosphate/tricalcium silicate composite bone cement

    International Nuclear Information System (INIS)

    Bioactivity, osteogenicity and mechanical properties of α-tricalcium phosphate (α-TCP) based phosphates cements can be improved by adding tricalcium silicate (C3S); however, the addition of C3S delays the precipitation and growth of calcium deficient hydroxyapatite (CDHA). Thus, the aim of this work was the study of in situ setting reaction of α-TCP/C3S composite bone cement under high energy X-ray generated by a synchrotron source within the first 72h. The results showed that the addition of C3S induces the precipitation of nanosized CDHA at early times depending on the added content. Calculated crystallite sizes showed that the higher the content of C3S, the smaller the crystal size at the beginning of the precipitation. These results are different from those obtained by conventional XRD method, suggesting that the proposed technique is a powerful tool in determining the composition and extent of reaction of CPCs surfaces in real time. (author)

  2. In situ synchrotron X-ray powder diffraction study of the early hydration of α-tricalcium phosphate/tricalcium silicate composite bone cement

    Energy Technology Data Exchange (ETDEWEB)

    Morejon-Alonso, Loreley; Correa, Jose Raul, E-mail: lmorejon@fq.uh.cu [Departamento de Quimica General, Facultad de Quimica, Universidad de La Habana, UH (Cuba); Motisuke, Mariana [Universidade Federal de Sao Paulo (UNIFESP), Sao Jose dos Campos, SP (Brazil); Carrodeguas, Raul Garcia [Universidade Federal de Campina Grande (UFCG), Campina Grande, PB (Brazil). Laboratorio de Avaliacao e Desenvolvimento de Biomateriais do Nordeste; Santos, Luis Alberto dos [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Escola de Engenharia. Departamento de Materiais

    2015-01-15

    Bioactivity, osteogenicity and mechanical properties of α-tricalcium phosphate (α-TCP) based phosphates cements can be improved by adding tricalcium silicate (C{sub 3}S); however, the addition of C{sub 3}S delays the precipitation and growth of calcium deficient hydroxyapatite (CDHA). Thus, the aim of this work was the study of in situ setting reaction of α-TCP/C{sub 3}S composite bone cement under high energy X-ray generated by a synchrotron source within the first 72h. The results showed that the addition of C{sub 3}S induces the precipitation of nanosized CDHA at early times depending on the added content. Calculated crystallite sizes showed that the higher the content of C{sub 3}S, the smaller the crystal size at the beginning of the precipitation. These results are different from those obtained by conventional XRD method, suggesting that the proposed technique is a powerful tool in determining the composition and extent of reaction of CPCs surfaces in real time. (author)

  3. Interactions between calcium phosphate and heavy metal ions in aqueous solution

    OpenAIRE

    Fernane F.; Boudia S.; Saouli H.

    2013-01-01

    Synthetic and natural calcium phosphates were tested for removal metallic pollution in aqueous solution. Calcium phosphates with Ca/P ratio between 1,33 and 1,67 are fluently called apatite. They have a strong capacity to immobilize metallic ions when they are brought into contact with aqueous solutions. Ca2+ ions can substituted completely or partly by cations such as metallic ions (Ni2+; Cu2+; Co2+ and Cd2+). PO43− ions can be replaced by anions such as AsO43−, CO32−, … etc. Sorption of Cu2...

  4. Synthesis and characterization of porous calcium phosphate; Sintesis y caracterizacion del fosfato de calcio poroso

    Energy Technology Data Exchange (ETDEWEB)

    Granados C, F.; Serrano G, J.; Bonifacio M, J. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)]. e-mail: fgc@nuclear.inin.mx

    2007-07-01

    The porous calcium phosphate was prepared by the continuous precipitation method using Ca(NO{sub 3}){sub 2}.4H{sub 2}O and NH{sub 4}H{sub 2}PO{sub 4} salts. The synthesized material was structurally and superficially characterized using the XRD, BET, IR TGA and SEM techniques. The obtained inorganic material was identified as calcium phosphate that presents a great specific area for what can be efficiently used as adsorbent material for adsorption studies in the radioactive wastes treatment present in aqueous solution. (Author)

  5. Casein Phosphopeptide-Amorphous Calcium Phosphate and Shear Bond Strength of Adhesives to Primary Teeth Enamel

    OpenAIRE

    Farokh Gisovar, Elham; Hedayati, Nassim; Shadman, Niloofar; Shafiee, Leila

    2015-01-01

    Background: CPP-ACP (Phosphopeptide-Amorphous Calcium Phosphate) has an important role in caries prevention in pediatric patients. This study was done, because of the great use of CPP-ACP and the need for restoration for teeth treated with CPP-ACP as well as the importance of shear bond strength of adhesives in the success of restorations. Objectives: This study aimed to evaluate the effect of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) on shear bond strength of dental adhesiv...

  6. Biomimetic Nanocomposites of Calcium Phosphate and Self-Assembling Triblock and Pentablock Copolymers

    Energy Technology Data Exchange (ETDEWEB)

    Drew Lenzen Enlow

    2006-08-09

    In an effort to mimic the growth of natural bone, self-assembling, micelle and gel-forming copolymers were used as a template for calcium phosphate precipitation. Because of the cationic characteristics imparted by PDEAEM end group additions to commercially available Pluronic{reg_sign} Fl27, a direct ionic attraction mechanism was utilized and a polymer-brushite nanocomposite spheres were produced. Brushite coated spherical micelles with diameters of {approx}40 nm, and agglomerates of these particles (on the order of 0.5 {mu}m) were obtained. Thickness and durability of the calcium phosphate coating, and the extent of agglomeration were studied. The coating has been shown to be robust enough to retain its integrity even below polymer critical micelle concentration and/or temperature. Calcium phosphate-polymer gel nanocomposites were also prepared. Gel samples appeared as a single phase network of agglomerated spherical micelles, and had a final calcium phosphate concentration of up to 15 wt%. Analysis with x-ray diffraction and NMR indicated a disordered brushite phase with the phosphate groups linking inorganic phase to the polymer.

  7. Monolithic calcium phosphate/poly(lactic acid) composite versus calcium phosphate-coated poly(lactic acid) for support of osteogenic differentiation of human mesenchymal stromal cells

    OpenAIRE

    Tahmasebi Birgani, Zeinab; van Blitterswijk, Clemens A; Habibovic, Pamela

    2016-01-01

    Calcium phosphates (CaPs), extensively used synthetic bone graft substitutes, are often combined with other materials with the aim to overcome issues related to poor mechanical properties of most CaP ceramics. Thin ceramic coatings on metallic implants and polymer-ceramic composites are examples of such hybrid materials. Both the properties of the CaP used and the method of incorporation into a hybrid structure are determinant for the bioactivity of the final construct. In the present study, ...

  8. Calcium-acidic phospholipid-phosphate complexes in human hydroxyapatite-containing pathologic deposits.

    OpenAIRE

    Boskey, A. L.; Bullough, P. G.; Vigorita, V.; Di Carlo, E

    1988-01-01

    The deposition of calcium-containing crystals in tissues is due to a combination of factors: elevation in the concentrations of precipitating ions, formation of specific nucleators, and removal of macromolecules that inhibit crystal deposition. This study tested the hypothesis that calcium acidic phospholipid phosphate complexes, which promote hydroxyapatite deposition both in vitro and in vivo, are associated only with hydroxyapatite deposits, and furthermore, that the presence of these comp...

  9. Biological responses of brushite-forming Zn- and ZnSr- substituted beta-tricalcium phosphate bone cements

    Directory of Open Access Journals (Sweden)

    S Pina

    2010-09-01

    Full Text Available The core aim of this study was to investigate zinc (Zn- and zinc and strontium (ZnSr-containing brushite-forming beta-tricalcium phosphate (TCP cements for their effects on proliferation and differentiation of osteoblastic-like cells (MC3T3-E1 cell line as well as for their in vivo behaviour in trabecular bone cylindrical defects in a pilot study. In vitro proliferation and maturation responses of MC3T3-E1 osteoblastic-like cells to bone cements were studied at the cellular and molecular levels. The Zn- and Sr-containing brushite cements were found to stimulate pre-osteoblastic proliferation and osteoblastic maturation. Indeed, MC3T3-E1 cells exposed to the powdered cements had increased proliferative rates and higher adhesiveness capacity, in comparison to control cells. Furthermore, they exhibited higher alkaline phosphatase (ALP activity and increased Type-I collagen secretion and fibre deposition into the extracellular matrix. Proliferative and collagen deposition properties were more evident for cells grown in cements doped with Sr. The in vivo osteoconductive propertiesof the ZnCPC and ZnSrCPC cements were also pursued. Histological and histomorphometric analyses were performed at 1 and 2 months after implantation, using carbonated apatite cement (Norian SRS® as control. There was no evidence of cement-induced adverse foreign body reactions, and furthermore ZnCPC and ZnSrCPC cements revealed better in vivo performance in comparison to the control apatite cement. Additionally, the presence of both zinc and strontium resulted in the highest rate of new bone formation. These novel results indicate that the investigated ZnCPC and ZnSrCPC cements are both biocompatible and osteoconductive, being good candidate materials to use as bone substitutes.

  10. The compressive modulus and strength of saturated calcium sulphate dihydrate cements: implications for testing standards.

    Science.gov (United States)

    Koh, Ilsoo; López, Alejandro; Helgason, Benedikt; Ferguson, Stephen J

    2014-06-01

    Calcium sulphate-based bone cement is a bone filler with proven biological advantages including biodegradability, biocompatibility and osteoconductivity. Mechanical properties of such brittle ceramic cements are frequently determined using the testing standard designed for ductile acrylic cements. The aims of the study were (1) to validate the suitability of this common testing protocol using saturated calcium sulphate dihydrate (CSD), and (2) to compare the strength and effective modulus of non-saturated and saturated CSD, in order to determine the changes in the mechanical behavior of CSD upon saturation. Unconfined compression tests to failure were performed on 190 cylindrical CSD samples. The samples were divided into four groups having different saturation levels (saturated, non-saturated) and end conditions (capped and non-capped). Two effective moduli were calculated per sample, based on the deformations measured using the machine platens and a sample-mounted extensometer. The effective moduli of non-saturated groups were found to be independent of the end conditions. The saturated and capped group showed no difference in the effective moduli derived from different measurement methods, while the saturated and non-capped group showed a significant difference between the machine platen- and extensometer-derived moduli. Strength and modulus values were significantly lower for saturated samples. It was assumed that the existence of water in saturated CSD alters the mechanical response of the material due to the changes in chemical and physical behaviors. These factors are considered to play important roles to decrease the shear strength of CSD. It was proposed that the reduction in CSD shear strength evokes local deformation at the platen-sample boundary, affecting the strength and effective moduli derived from the experiments. The results of this study highlighted the importance of appropriate and consistent testing methods when determining the mechanical

  11. The Microleakage of Polycarboxylate, Glass Ionomer and Zinc Phosphate Cements for Stainless Steel Crowns of Pulpotomized Primary Molars

    Directory of Open Access Journals (Sweden)

    Mahkameh Mirkarimi

    2013-01-01

    Full Text Available Background: Microleakage in Stainless Steel Crowns (SSC margins leads to seepage of oral fluids and bacteria and it is one of the reasons for treatments failures. The aim of this study was to assess the effect of zinc phosphate, glass Ionomer and polycarboxylate cements on microleakage of stainless steel crowns for primary pulpotomized molar teeth. Materials and Methods: In this experimental in vitro study, 60 extracted primary molar teeth were randomly divided in to three groups (n=20. Stainless steel crowns were fitted for each tooth after pulpotomy procedures. Crowns were luted with a zinc phosphate, glass ionomer or polycarboxylate cement. All specimens were stored in 100% humidity at 37o C for 1 hour and termocycled 500 times (5ºC to 55ºC with a 30 seconds dwell time and then immersed in 0.5% basic fuschin solution for 24 hours. The specimens were sectioned buccolingually and each section was evaluated for microleakage under a stereomicroscope.Results: In zinc phosphate group 45% of spicemens and in glass ionomer group there was 5% of spicemens showed leakage extending on to occlusal aspect and in polycarboxylate group none of the spicemens had this situation. According to the kruskal wallis test in all groups there were significant differences in microleakage (p< 0.001.Conclusion: The use of zinc phosphate cement resulted in the highest percentage of microleakage. The microleakage of SSCs cemented with polycarboxylate and glass ionomer were similar.

  12. Magnesium substitution in the structure of orthopedic nanoparticles: A comparison between amorphous magnesium phosphates, calcium magnesium phosphates, and hydroxyapatites

    International Nuclear Information System (INIS)

    As biocompatible materials, magnesium phosphates have received a lot of attention for orthopedic applications. During the last decade multiple studies have shown advantages for magnesium phosphate such as lack of cytotoxicity, biocompatibility, strong mechanical properties, and high biodegradability. The present study investigates the role of Mg+2 and Ca+2 ions in the structure of magnesium phosphate and calcium phosphate nanoparticles. To directly compare the effect of Mg+2 and Ca+2 ions on structure of nanoparticles and their biological behavior, three groups of nanoparticles including amorphous magnesium phosphates (AMPs) which release Mg+2, calcium magnesium phosphates (CMPs) which release Mg+2 and Ca+2, and hydroxyapatites (HAs) which release Ca+2 were studied. SEM, TEM, XRD, and FTIR were used to evaluate the morphology, crystallinity, and chemical properties of the particles. AMP particles were homogeneous nanospheres, whereas CMPs were combinations of heterogeneous nanorods and nanospheres, and HAs which contained heterogeneous nanosphere particles. Cell compatibility was monitored in all groups to determine the cytotoxicity effect of particles on studied MC3T3-E1 preosteoblasts. AMPs showed significantly higher attachment rate than the HAs after 1 day and both AMPs and CMPs showed significantly higher proliferation rate when compared to HAs after 7 days. Gene expression level of osteoblastic markers ALP, COL I, OCN, OPN, RUNX2 were monitored and they were normalized to GAPDH housekeeping gene. Beta actin expression level was monitored as the second housekeeping gene to confirm the accuracy of results. In general, AMPs and CMPs showed higher expression level of osteoblastic genes after 7 days which can further confirm the stimulating role of Mg+2 and Ca+2 ions in increasing the proliferation rate, differentiation, and mineralization of MC3T3-E1 preosteoblasts. - Highlights: • Role of Mg2+ and Ca2+ ions in proliferation, and differentiation of

  13. Influence of calcium sulfoaluminate cement on the pullout performance of reinforcing fibers: An evaluation of the micro-mechanical behavior

    Science.gov (United States)

    Jewell, Robert Benjamin

    The objective of this research was to determine the influence of calcium sulfoaluminate (CSA) cement on reinforcing fibers by evaluating the fiber pullout behavior, and bonding characteristics, of a single fiber embedded in a cementitious paste matrix. Four types of fibers commonly used in industry were evaluated: 1) Polyvinyl alcohol; 2) Polypropylene; 3) Coated Steel; and 4) Plain Steel. Upward trends in energy costs and potential greenhouse gas regulations favor an increased use of construction materials that require lower energy and lower CO2 emissions to fabricate, such as CSA cement, as opposed to the production of ordinary portland cement (OPC), which is more energy intensive and produces more CO2 emissions. However, widespread use of CSA cement requires a more in-depth understanding of the engineering characteristics that govern its performance, including interaction with reinforcing fibers. The overarching objective of this research was to provide the engineering base needed for the utilization of reinforcing fibers in CSA cement-based construction materials. The aims of the research were (1) to develop an ettringite-rich calcium sulfoaluminate cement, and (2) evaluate the pullout characteristics of reinforcing fibers embedded in a CSA-cement matrix. Key elements of the strategy included (1) Compare the performance of a laboratory-fabricated CSA cement to a commercial CSA cement and OPC, (2) Evaluate the peak load, and toughness of reinforcing fibers in CSA cement and OPC, (3) Evaluate the debonding-energy density and multiple-cracking behavior of fibers in CSA cement and OPC, and (4) Evaluate the shear bond strength of reinforcing fibers in CSA cement and OPC. Based on the findings of this PhD dissertation, calcium sulfoaluminate cement has a significant influence on the characteristics and behavior of embedded reinforcing fibers. An important factor contributing to the bond strength between fiber and matrix was the ability to transfer interfacial

  14. Effect of ultrasonic instrumentation on the bond strength of crowns cemented with zinc phosphate cement to natural teeth. An in vitro study

    Directory of Open Access Journals (Sweden)

    Antonio Braulino de Melo Filho

    2008-09-01

    Full Text Available Several studies have reported the benefits of sonic and/or ultrasonic instrumentation for root debridement, with most of them focusing on changes in periodontal clinical parameters. The present study investigated possible alterations in the tensile bond strength of crowns cemented with zinc phosphate cement to natural teeth after ultrasonic instrumentation. Forty recently extracted intact human third molars were selected, cleaned and stored in physiologic serum at 4°C. They received standard preparations, at a 16º convergence angle, and AgPd alloy crowns. The crowns were cemented with zinc phosphate cement and then divided into four groups of 10 teeth each. Each group was then subdivided into two subgroups, with one of the subgroups being submitted to 5,000 thermal cycles ranging from 55 ± 2 to 5 ± 2°C, while the other was not. Each group was submitted to ultrasonic instrumentation for different periods of time: group 1 - 0 min (control, group 2 - 5 min, group 3 - 10 min, and group 4 - 15 min. Tensile bond strength tests were performed with an Instron testing machine (model 4310. Statistical analysis was performed using ANOVA and Tukey's test at the 5% level of significance. A significant reduction in the tensile bond strength of crowns cemented with zinc phosphate and submitted to thermal cycles was observed at 15 min (196.75 N versus 0 min = 452.01 N, 5 min = 444.23 N and 10 min = 470.85 N. Thermal cycling and ultrasonic instrumentation for 15 min caused a significant reduction in tensile bond strength (p < .05.

  15. Stabilization of ZnCl2-Containing Waste Using Calcium Sulfoaluminate Cement

    International Nuclear Information System (INIS)

    The potential of calcium sulfoaluminate (CSA) cement was investigated to solidify and stabilize radwastes containing large amounts of soluble zinc chloride (a strong inhibitor of Portland cement hydration). Hydration of pastes and mortars prepared with a 0.5 mol/L ZnCl2 mixing solution was characterized over one year as a function of the gypsum content of the binder and the thermal history of the material. Blending the CSA clinker with 20% gypsum enabled rapid hydration, with only very small delay compared with a reference prepared with pure water. It also improved the compressive strength of the hardened material and significantly reduced its expansion under wet curing. Moreover, the hydrate assemblage was less affected by a thermal treatment at early age simulating the temperature rise and fall occurring in a large-volume drum of cemented waste. Fully hydrated materials contained ettringite, amorphous aluminum hydroxide, straetlingite, together with AFm phases (Kuzel's salt associated with monosulfoaluminate or Friedel's salt depending on the gypsum content of the binder), and possibly C-(A)-S-H. Zinc was readily insolubilized and could not be detected in the pore solution extracted from cement pastes, or in their leachates after 3 months of leaching by pure water at pH 7. The good retention of zinc by the cement matrix was mainly attributed to the precipitation of a hydrated and well crystallized phase with platelet morphology (which may belong to the layered double hydroxides family) at early age ≤ 1 day), and to chemisorption onto aluminum hydroxide at later age. (author)

  16. Effect of Incorporating Nanoporous Metal Phosphate Materials on the Compressive Strength of Portland Cement

    Directory of Open Access Journals (Sweden)

    Dawn M. Wellman

    2008-01-01

    Full Text Available Nanoporous metal phosphate (NP-MPO materials are being developed for removal of contaminant oxyanions (As(OHO32−, CrO42−, and TcO4−, and cations (mercury, cadmium, and lead from water and waste streams. Following sequestration, incorporation of metal laden NP-MPOs as a portion of cement formulation would provide an efficient and low-cost way to immobilize metal laden NP-MPOs in an easily handled waste form suitable for permanent disposal. There are no known investigations regarding the incorporation of NP-MPOs in concrete and the effects imparted on the physical and mechanical properties of concrete. Results of this investigation demonstrated that incorporating of NP-MPO materials requires additional water in the concrete formulation which decreases the compressive strength. Thus, incorporation of NP-MPOs in concrete may not serve as an efficient means for long-term disposal.

  17. Hard tissue deposition in dental pulp canal by {alpha}-tricalcium phosphate cement

    Energy Technology Data Exchange (ETDEWEB)

    Yoshikawa, M.; Toda, T. [Osaka Dental Univ. (Japan). Dept. of Endodontics; Mandai, Y. [Bio-Chemical Lab. of Nitta Gelatin Inc., Yao (Japan); Oonishi, H. [Osaka Minami National Hospital, Kawachi (Japan). Dept. of Orthopaedic Surgery

    2001-07-01

    Canal closure by hard tissue proliferation in the pulp canal and/or apical foramen is the most ideal healing after pulp removal. Generally, Ca(OH){sub 2} may induce secondary dentine or dentine-bridge on the amputated pulp surface. However, Ca(OH){sub 2} shows strong alkalinity and may cause severe inflammatory responses in the residual pulp. Moreover, completely formed dentine-bridge at the orifice will disturb further treatment of residual pulp because of the difficulty in localizing the pathway. The purpose of this study was to see hard tissue induction using newly developed {alpha}-tricalcium phosphate cement and to recognize the morphological difference of hard tissue from that of Ca(OH){sub 2}. (orig.)

  18. Effects of Silicate, Phosphate, and Calcium on the Stability of Aldopentoses

    Science.gov (United States)

    Nitta, Sakiko; Furukawa, Yoshihiro; Kakegawa, Takeshi

    2016-06-01

    Ribose is an important constituent of RNA: ribose connects RNA bases and forms a strand of sugar phosphates. Accumulation of ribose on prebiotic Earth was difficult because of its low stability. Improvement in the yield of ribose by the introduction of borate or silicate in a formose-like reaction has been proposed. The effects of borates have been further analyzed and confirmed in subsequent studies. Nonetheless, the effects of silicates and phosphates remain unclear. In the present study, we incubated aldopentoses in a highly alkaline aqueous solution at a moderate temperature to determine the effects of silicate or phosphate on the degradation rates of ribose and its isomeric aldopentoses. The formation of a complex of silicate (or phosphate) with ribose was also analyzed in experiments with 29Si and 31P nuclear magnetic resonance (NMR). We found that silicate or phosphate complexes of ribose were not detectable under our experimental conditions. The stability of ribose and lyxose improved after addition of 40-fold molar excess (relative to a pentose) of sodium silicate or sodium phosphate to the alkaline solution. The stability was not improved further when an 80-fold molar excess of sodium silicate or sodium phosphate was added. Calcium was removed from these solutions by precipitation of calcium salts. The drop in Ca2+ concentration might have improved the stability of ribose and lyxose, which are susceptible to aldol addition. The improvement of ribose stability by the removal of Ca2+ and by addition of silicate or phosphate was far smaller than the improvement by borate. Furthermore, all aldopentoses showed similar stability in silicate- and phosphate-containing solutions. These results clearly show that selective stabilization of ribose by borate cannot be replaced by the effects of silicate or phosphate; this finding points to the importance of borate in prebiotic RNA formation.

  19. Effects of Silicate, Phosphate, and Calcium on the Stability of Aldopentoses.

    Science.gov (United States)

    Nitta, Sakiko; Furukawa, Yoshihiro; Kakegawa, Takeshi

    2016-06-01

    Ribose is an important constituent of RNA: ribose connects RNA bases and forms a strand of sugar phosphates. Accumulation of ribose on prebiotic Earth was difficult because of its low stability. Improvement in the yield of ribose by the introduction of borate or silicate in a formose-like reaction has been proposed. The effects of borates have been further analyzed and confirmed in subsequent studies. Nonetheless, the effects of silicates and phosphates remain unclear. In the present study, we incubated aldopentoses in a highly alkaline aqueous solution at a moderate temperature to determine the effects of silicate or phosphate on the degradation rates of ribose and its isomeric aldopentoses. The formation of a complex of silicate (or phosphate) with ribose was also analyzed in experiments with (29)Si and (31)P nuclear magnetic resonance (NMR). We found that silicate or phosphate complexes of ribose were not detectable under our experimental conditions. The stability of ribose and lyxose improved after addition of 40-fold molar excess (relative to a pentose) of sodium silicate or sodium phosphate to the alkaline solution. The stability was not improved further when an 80-fold molar excess of sodium silicate or sodium phosphate was added. Calcium was removed from these solutions by precipitation of calcium salts. The drop in Ca(2+) concentration might have improved the stability of ribose and lyxose, which are susceptible to aldol addition. The improvement of ribose stability by the removal of Ca(2+) and by addition of silicate or phosphate was far smaller than the improvement by borate. Furthermore, all aldopentoses showed similar stability in silicate- and phosphate-containing solutions. These results clearly show that selective stabilization of ribose by borate cannot be replaced by the effects of silicate or phosphate; this finding points to the importance of borate in prebiotic RNA formation. PMID:26559965

  20. Improved workability of injectable calcium sulfate bone cement by regulation of self-setting properties

    International Nuclear Information System (INIS)

    Calcium sulfate hemihydrate (CSH) powder as an injectable bone cement was prepared by hydrothermal synthesis of calcium sulfate dihydrate (CSD). The prepared materials showed X-ray diffraction peaks corresponding to the CSH structure without any secondary phases, implying complete conversion from CSD phase to CSH phase. Thermogravimetric (TG) analyses showed the crystal water content of CSH was about 6.0% (wt.), which is near to the theoretic crystal water value of CSH. From scanning electron microscopy (SEM) micrographs, sheet crystal structure of CSD was observed to transform into rod-like crystal structure of CSH. Most interesting and important of all, CSD as setting accelerator was also introduced into CSH powder to regulate self-setting properties of injectable CSH paste, and thus the self-setting time of CSH paste can be regulated from near 30 min to less than 5 min by adding various amounts of setting accelerator. Because CSD is not only the reactant of preparing CSH but also the final solidified product of CSH, the setting accelerator has no significant effect on the other properties of materials, such as mechanical properties. In vitro biocompatibility and in vivo histology studies have demonstrated that the materials have good biocompatibility and good efficacy in bone regeneration. All these will further improve the workability of CSH in clinic applications. Highlights: ► Calcium sulfate hemihydrate (CSH) can be an injectable bone cement. ► CSH was produced by hydrothermal synthesis of calcium sulfate dihydrate (CSD). ► CSD was introduced into CSH powder to regulate self-setting properties of CSH. ► Setting accelerator has no significant effect on the other properties of materials. ► Injectable CSH has good biocompatibility and good efficacy in bone regeneration

  1. Improved workability of injectable calcium sulfate bone cement by regulation of self-setting properties

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Zonggang, E-mail: chenzg@sdu.edu.cn [National Glycoengineering Research Center, Shandong University, Jinan 250100 (China); Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Liu, Huanye [Department of Orthodontics, School of Stomatology, China Medical University, Shenyang 110001 (China); Liu, Xi [Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Lian, Xiaojie [College of Mechanics, Taiyuan University of Technology, Taiyuan 030024 (China); Guo, Zhongwu [National Glycoengineering Research Center, Shandong University, Jinan 250100 (China); Jiang, Hong-Jiang [Wendeng Hospital of Traditional Chinese Orthopedics and Traumatology, Shandong 264400 (China); Cui, Fu-Zhai, E-mail: cuifz@mail.tsinghua.edu.cn [Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)

    2013-04-01

    Calcium sulfate hemihydrate (CSH) powder as an injectable bone cement was prepared by hydrothermal synthesis of calcium sulfate dihydrate (CSD). The prepared materials showed X-ray diffraction peaks corresponding to the CSH structure without any secondary phases, implying complete conversion from CSD phase to CSH phase. Thermogravimetric (TG) analyses showed the crystal water content of CSH was about 6.0% (wt.), which is near to the theoretic crystal water value of CSH. From scanning electron microscopy (SEM) micrographs, sheet crystal structure of CSD was observed to transform into rod-like crystal structure of CSH. Most interesting and important of all, CSD as setting accelerator was also introduced into CSH powder to regulate self-setting properties of injectable CSH paste, and thus the self-setting time of CSH paste can be regulated from near 30 min to less than 5 min by adding various amounts of setting accelerator. Because CSD is not only the reactant of preparing CSH but also the final solidified product of CSH, the setting accelerator has no significant effect on the other properties of materials, such as mechanical properties. In vitro biocompatibility and in vivo histology studies have demonstrated that the materials have good biocompatibility and good efficacy in bone regeneration. All these will further improve the workability of CSH in clinic applications. Highlights: ► Calcium sulfate hemihydrate (CSH) can be an injectable bone cement. ► CSH was produced by hydrothermal synthesis of calcium sulfate dihydrate (CSD). ► CSD was introduced into CSH powder to regulate self-setting properties of CSH. ► Setting accelerator has no significant effect on the other properties of materials. ► Injectable CSH has good biocompatibility and good efficacy in bone regeneration.

  2. Grafting cyclodextrins to calcium phosphate ceramics for biomedical applications

    DEFF Research Database (Denmark)

    Jacobsen, P.A.L.; Nielsen, J.L.; Juhl, M.V.;

    2012-01-01

    The grafting of hydroxyapatite/beta-tricalcium phosphate with β-cyclodextrin was achieved using a two step reaction with (3-glycidyloxypropyl)trimethoxysilane as a linker. Firstly, the silane group was brought to react with the hydroxyl groups at the surface of the hydroxyapatite/beta-tricalcium ...

  3. Osteogenesis and angiogenesis properties of dental pulp cell on novel injectable tricalcium phosphate cement by silica doped

    International Nuclear Information System (INIS)

    β-Tricalcium phosphate (β-TCP) is an osteoconductive material in clinical. In this study, we have doped silica (Si) into β-TCP and enhanced its bioactive and osteostimulative properties. To check its effectiveness, a series of Si-doped with different ratios were prepared to make new bioactive and biodegradable biocomposites for bone repair. Formation of the diametral tensile strength, ions released and weight loss of cements was considered after immersion. In addition, we also examined the behavior of human dental pulp cells (hDPCs) cultured on Si-doped β-TCP cements. The results showed that setting time and injectability of the Si-doped β-TCP cements were decreased as the Si content was increased. At the end of the immersion point, weight losses of 30.1%, 36.9%, 48.1%, and 55.3% were observed for the cement doping 0%, 10%, 20%, and 30% Si into β-TCP cements, respectively. In vitro cell experiments show that the Si-rich cements promote human dental pulp cell (hDPC) proliferation and differentiation. However, when the Si-doped in the cement is more than 20%, the amount of cells and osteogenesis protein of hDPCs was stimulated by Si released from Si-doped β-TCP cements. The degradation of β-TCP and osteogenesis of Si gives a strong reason to believe that these Si-doped β-TCP cements may prove to be promising bone repair materials. - Highlights: • The higher the Si in the cement, the shorter the setting time and the higher the DTS. • Si20-doped in TCP improved cell adhesion, proliferation and differentiation. • The Si ion stimulated collagen secreted from cells. • The Si released from substrate can promote osteogenic and angiogenic

  4. Osteogenesis and angiogenesis properties of dental pulp cell on novel injectable tricalcium phosphate cement by silica doped

    Energy Technology Data Exchange (ETDEWEB)

    Su, Ying-Fang [Institute of Medicine, Chung Shan Medical University, Taichung, Taiwan (China); Department of Stomatology, Chung Shan Medical University Hospital, Taichung, Taiwan (China); School of Dentistry, Chung Shan Medical University, Taichung, Taiwan (China); Lin, Chi-Chang, E-mail: chichang31@gmail.com [Department of Anatomy, Chung Shan Medical University, Taichung City, Taiwan (China); Huang, Tsui-Hsien; Chou, Ming-Yung [Department of Stomatology, Chung Shan Medical University Hospital, Taichung, Taiwan (China); School of Dentistry, Chung Shan Medical University, Taichung, Taiwan (China); Yang, Jaw-Ji, E-mail: jjyang@csmu.edu.tw [Department of Chemical and Materials Engineering, Tunghai University, Taichung, Taiwan (China); Shie, Ming-You, E-mail: eviltacasi@gmail.com [Department of Anatomy, Chung Shan Medical University, Taichung City, Taiwan (China)

    2014-09-01

    β-Tricalcium phosphate (β-TCP) is an osteoconductive material in clinical. In this study, we have doped silica (Si) into β-TCP and enhanced its bioactive and osteostimulative properties. To check its effectiveness, a series of Si-doped with different ratios were prepared to make new bioactive and biodegradable biocomposites for bone repair. Formation of the diametral tensile strength, ions released and weight loss of cements was considered after immersion. In addition, we also examined the behavior of human dental pulp cells (hDPCs) cultured on Si-doped β-TCP cements. The results showed that setting time and injectability of the Si-doped β-TCP cements were decreased as the Si content was increased. At the end of the immersion point, weight losses of 30.1%, 36.9%, 48.1%, and 55.3% were observed for the cement doping 0%, 10%, 20%, and 30% Si into β-TCP cements, respectively. In vitro cell experiments show that the Si-rich cements promote human dental pulp cell (hDPC) proliferation and differentiation. However, when the Si-doped in the cement is more than 20%, the amount of cells and osteogenesis protein of hDPCs was stimulated by Si released from Si-doped β-TCP cements. The degradation of β-TCP and osteogenesis of Si gives a strong reason to believe that these Si-doped β-TCP cements may prove to be promising bone repair materials. - Highlights: • The higher the Si in the cement, the shorter the setting time and the higher the DTS. • Si20-doped in TCP improved cell adhesion, proliferation and differentiation. • The Si ion stimulated collagen secreted from cells. • The Si released from substrate can promote osteogenic and angiogenic.

  5. The determination of calcium in phosphate, carbonate, and silicate rocks by flame photometer

    Science.gov (United States)

    Kramer, Henry

    1956-01-01

    A method has been developed for the determination of calcium in phosphate, carbonate, and silicate rocks using the Beckman flame photometer, with photomultiplier attachement. The sample is dissolved in hydrofluoric, nitric, and perchloric acids, the hydrofluoric and nitric acids are expelled, a radiation buffer consisting of aluminum, magnesium, iron, sodium, potassium, phosphoric acid, and nitric acid is added, and the solution is atomized in an oxy-hydrogen flame with an instrument setting of 554 mµ. Measurements are made by comparison against calcium standards, prepared in the same manner, in the 0 to 50 ppm range. The suppression of calcium emission by aluminum and phosphate was overcome by the addition of a large excess of magnesium. This addition almost completely restores the standard curve obtained from a solution of calcium nitrate. Interference was noted when the iron concentration in the aspirated solution (including the iron from the buffer) exceeded 100 ppm iron. Other common rock-forming elements did not interfere. The results obtained by this procedure are within ± 2 percent of the calcium oxide values obtained by other methods in the range 1 to 95 percent calcium oxide. In the 0 to 1 percent calcium oxide range the method compares favorably with standard methods.

  6. Surface modification of porous polycaprolactone/biphasic calcium phosphate scaffolds for bone regeneration in rat calvaria defect.

    Science.gov (United States)

    Kim, Ji-Hyun; Linh, Nguyen T B; Min, Young K; Lee, Byong-Taek

    2014-10-01

    In this study, polycaprolactone scaffolds fabricated by a salt-leaching process were loaded with biphasic calcium phosphate successfully to improve the osteoconductivity in bone regeneration. The surface of polycaprolactone/biphasic calcium phosphate scaffolds was aminolyzed by 1,6-hexamethylenediamine to introduce amino groups onto the surface, which was verified qualitatively by ninhyrin staining. Collagen was further immobilized on the aminolyzed porous polycaprolactone via N-ethyl-N'-(3-dimethylaminopropy) carbodiimide hydrochloride/hydroxy-2,5-dioxopyrolidine-3-sulfonic acid sodium cross-linking. The pore size of polycaprolactone/biphasic calcium phosphate-collagen scaffolds was 200-300 µm, which was suitable for bone in-growth. The X-ray photoelectron spectroscopy confirmed the coupling of collagen immobilized on the surface of polycaprolactone/biphasic calcium phosphate. In vitro results demonstrated that the spreading and viability of MC3T3-E1 cells were remarkably improved in the polycaprolactone/biphasic calcium phosphate-collagen scaffolds. The in vivo study was carried out by implanting the porous polycaprolactone, polycaprolactone/biphasic calcium phosphate, and polycaprolactone/biphasic calcium phosphate-collagen to the skulls of rats. Although the addition of biphasic calcium phosphate particles in the polycaprolactone scaffolds does not have a strong effect on the new bone formation, the immobilization of collagen on the polycaprolactone/biphasic calcium phosphate scaffolds significantly improved the bone regeneration even though the implantation time was short, 6 weeks. The present results provide more evidence that functionalizing polycaprolactone with biphasic calcium phosphate and collagen may be a feasible way to improve the osteoconduction in bone regeneration. PMID:24939961

  7. Treatment of acute thoracolumbar burst fractures with kyphoplasty and short pedicle screw fixation: Transpedicular intracorporeal grafting with calcium phosphate: A prospective study

    Directory of Open Access Journals (Sweden)

    Korovessis Panagiotis

    2007-01-01

    Full Text Available Background: In the surgical treatment of thoracolumbar fractures, the major problem after posterior correction and transpedicular instrumentation is failure to support the anterior spinal column, leading to loss of correction and instrumentation failure with associated complaints. We conducted this prospective study to evaluate the outcome of the treatment of acute thoracolumbar burst fractures by transpedicular balloon kyphoplasty, grafting with calcium phosphate cement and short pedicle screw fixation plus fusion. Materials and Methods : Twenty-three consecutive patients of thoracolumbar (T 9 to L 4 burst fracture with or without neurologic deficit with an average age of 43 years, were included in this prospective study. Twenty-one from the 23 patients had single burst fracture while the remaining two patients had a burst fracture and additionally an adjacent A1-type fracture. On admission six (26% out of 23 patients had neurological deficit (five incomplete, one complete. Bilateral transpedicular balloon kyphoplasty with liquid calcium phosphate to reduce segmental kyphosis and restore vertebral body height and short (three vertebrae pedicle screw instrumentation with posterolateral fusion was performed. Gardner kyphosis angle, anterior and posterior vertebral body height ratio and spinal canal encroachment were calculated pre- to postoperatively. Results : All 23 patients were operated within two days after admission and were followed for at least 12 months after index surgery. Operating time and blood loss averaged 45 min and 60 cc respectively. The five patients with incomplete neurological lesions improved by at least one ASIA grade, while no neurological deterioration was observed in any case. The VAS and SF-36 (Role physical and Bodily pain domains were significantly improved postoperatively. Overall sagittal alignment was improved from an average preoperative 16° to one degree kyphosis at final follow-up observation. The anterior

  8. Lead Retention in a Calcareous Soil Influenced by Calcium and Phosphate Amendments

    Science.gov (United States)

    Phosphate amendments in calcareous lead (Pb)-contaminated soils to immobilize Pb may be hindered due to competition of Pb with calcium (Ca) that may inhibit the retention of Pb as a precipitation mechanism. This study explored the retention of Pb in a calcareous soil spiked and ...

  9. Dense and porous titanium substrates with a biomimetic calcium phosphate coating

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, A.A., E-mail: aantunesr@yahoo.com.br [Powder Technology Laboratory, Materials Processing and Characterization Division, National Institute of Technology, No. 82 Venezuela Avenue, Room 602, 20081-312 Rio de Janeiro, RJ (Brazil); Balestra, R.M. [Powder Technology Laboratory, Materials Processing and Characterization Division, National Institute of Technology, No. 82 Venezuela Avenue, Room 602, 20081-312 Rio de Janeiro, RJ (Brazil); Rocha, M.N. [Metallurgical and Materials Engineering Program, COPPE, Federal University of Rio de Janeiro, P.O. Box 68505, 21941-972 Rio de Janeiro, RJ (Brazil); Peripolli, S.B. [Materials Metrology Division, National Institute of Metrology, Normalization and Quality, No. 50 Nossa Senhora das Gracas Street, Building 3, 25250-020 Duque de Caxias, RJ (Brazil); Andrade, M.C. [Polytechnic Institute of Rio de Janeiro, Rio de Janeiro State University, s/n, Alberto Rangel Street, 28630-050 Nova Friburgo, RJ (Brazil); Pereira, L.C. [Metallurgical and Materials Engineering Program, COPPE, Federal University of Rio de Janeiro, P.O. Box 68505, 21941-972 Rio de Janeiro, RJ (Brazil); Oliveira, M.V. [Powder Technology Laboratory, Materials Processing and Characterization Division, National Institute of Technology, No. 82 Venezuela Avenue, Room 602, 20081-312 Rio de Janeiro, RJ (Brazil)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer A biomimetic coating method with simplified solution is proposed. Black-Right-Pointing-Pointer Titanium substrates are submitted to chemical and heat treatments. Black-Right-Pointing-Pointer Titanium substrates are coated with biocompatible calcium phosphate phases. Black-Right-Pointing-Pointer The simplified solution shows potential to be applied as a coating technique. - Abstract: The present work studied a biomimetic method using a simplified solution (SS) with calcium and phosphorus ions for coating titanium substrates, in order to improve their bioactivity. Commercially pure titanium dense sheet, microporous and macroporous titanium samples, both produced by powder metallurgy, were treated in NaOH solution followed by heat-treating and immersed in SS for 7, 14 or 21 days. The samples characterization was performed by quantitative metallographic analysis, confocal scanning optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and low angle X-ray diffraction. The results showed coatings with calcium phosphate precipitation in all samples, with globular or plate-like morphology, typical of hydroxyapatite and octacalcium phosphate, respectively, indicating that the solution (SS) has potential for coating titanium substrates. In addition, the different surfaces of substrates had an effect on the formed calcium phosphate phase and thickness of coatings, depending on the substrate type and imersion time in the simplified solution.

  10. Adjuvant effects of chitosan and calcium phosphate particles in an inactivated Newcastle disease vaccine

    Science.gov (United States)

    The adjuvant activity of chitosan and calcium phosphate-particles (CAP) was studied following intranasal coadministration of commercial chickens with inactivated Newcastle disease virus (NDV) vaccine. After three vaccinations with inactivated NDV in combination with chitosan or CAP an increase in an...

  11. Transformation of amorphous calcium phosphate to crystalline dahillite in the radular teeth of chitons.

    Science.gov (United States)

    Lowenstam, H A; Weiner, S

    1985-01-01

    A comparison of infrared spectra from individual teeth along the radula of a chiton (Polyplacophora, Mollusca) shows that the first-formed calcium phosphate mineral is amorphous. Over a period of weeks the mineral transforms to dahllite. The c axes of the dahllite crystals are aligned approximately perpendicular to the tooth surface. PMID:17810022

  12. Transformation of Amorphous Calcium Phosphate to Crystalline Dahllite in the Radular Teeth of Chitons

    Science.gov (United States)

    Lowenstam, H. A.; Weiner, S.

    1985-01-01

    A comparison of infrared spectra from individual teeth along the radula of a chiton (Polyplacophora, Mollusca) shows that the first-formed calcium phosphate mineral is amorphous. Over a period of weeks the mineral transforms to dahllite. The c axes of the dahllite crystals are aligned approximately perpendicular to the tooth surface.

  13. In vivo performance of microstructured calcium phosphate formulated in novel water-free carriers

    NARCIS (Netherlands)

    Davison, N.L.; Yuan, H.; Bruijn, de J.D.; Barrere-de Groot, F.YF.

    2012-01-01

    Osteoinductive calcium phosphate (CaP) ceramics can be combined with polymeric carriers to make shapeable bone substitutes as an alternative to autologous bone; however, carriers containing water may degrade the ceramic surface microstructure, which is crucial to bone formation. In this study five n

  14. Methotrexate loaded self stabilized calcium phosphate nanoparticles: a novel inorganic carrier for intracellular drug delivery.

    Science.gov (United States)

    Mukesh, Ukawala; Kulkarni, Vijay; Tushar, Rajyaguru; Murthy, R S R

    2009-02-01

    Calcium phosphate is considered as a potential biomaterial for drug and gene delivery because of its excellent features. In this study, we reported the formulation and characterization of calcium phosphate nanoparticle containing anticancer drug, methotrexate (MTX). Calcium phosphate nanoparticles containing MTX (CaPi-MTX) were prepared by reverse micelles technique. CaPi-MTX nanoparticles of average size 262 +/- 47.64 nm with entrapment efficiency of 58.04 +/- 4.09% were obtained. The IR spectrum of CaPi-MTX showed characteristics of composite formation of hydroxyapatite with MTX. X-RD analysis revealed that, CaPi-MTX nanoparticles were crystalline and in hydroxyapatite form. TEM studies showed that CaPi-MTX nanoparticles were spherical in shape. In vitro release study of CaPi-MTX nanoparticles showed slow release of MTX at physiological pH (pH 7.4) while > 90% release was observed within 3-4 hours at endosomal pH (pH 5.5 and pH 6.0). Confocal microscopy was performed using CHO cell lines, showed intracellular localization of FITC-Dextran loaded calcium phosphate nanoparticles. Results indicate that prepared CaPi-MTX nanoparticles could serve the purpose for intracellular drug delivery. PMID:20055112

  15. The role of prenucleation clusters in surface-induced calcium phosphate crystallization

    Science.gov (United States)

    Dey, Archan; Bomans, Paul H. H.; Müller, Frank A.; Will, Julia; Frederik, Peter M.; de With, Gijsbertus; Sommerdijk, Nico A. J. M.

    2010-12-01

    Unravelling the processes of calcium phosphate formation is important in our understanding of both bone and tooth formation, and also of pathological mineralization, for example in cardiovascular disease. Serum is a metastable solution from which calcium phosphate precipitates in the presence of calcifiable templates such as collagen, elastin and cell debris. A pathological deficiency of inhibitors leads to the uncontrolled deposition of calcium phosphate. In bone and teeth the formation of apatite crystals is preceded by an amorphous calcium phosphate (ACP) precursor phase. ACP formation is thought to proceed through prenucleation clusters-stable clusters that are present in solution already before nucleation-as was recently demonstrated for CaCO3 (refs 15,16). However, the role of such nanometre-sized clusters as building blocks for ACP has been debated for many years. Here we demonstrate that the surface-induced formation of apatite from simulated body fluid starts with the aggregation of prenucleation clusters leading to the nucleation of ACP before the development of oriented apatite crystals.

  16. Calcium phosphate coating on magnesium alloy by biomimetic method :Investigation of morphology ,composition and formation process

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Magnesium alloy has similar mechanical properties with natural bone and can degrade via corrosion in the electrolytic environment of the human body.Calcium phosphate has been proven to possess bioactivity and bone inductivity.In order to integrate both advantages,calcium phosphate coating was fabricated on magnesium alloy by a biomimetic method.Supersaturated calcification solutions (SCSs) with different Ca/P ratio and C1- concentration were used as mimetic solutions.The morphology,composition and formation process of the coating were studied with scanning electron microscopy (SEM),energy dispersive spectrometer (EDS),Fourier transformed infrared spectroscopy (FTIR) and X-ray diffraction (XRD).The results show that a uniform calcium phosphate coating was observed on magnesium alloy,the properties of which could be adjusted by the SCSs with different Ca/P ratio.The formation process of the coating was explored by immersing magnesium alloy in SCSs with different Cl- concentration which could adjust the hydrogen production.According to SEM results,the hydrogen bubbles were associated with the formation of grass-like and flower-like coating morphologies.In conclusion,the biomimetic method was effective to form calcium phosphate coating on magnesium alloy and the morphology and composition of the coating could be accommodated by the Ca/P ratio and Cl- concentration in SCSs.

  17. Novel sol–gel derived calcium phosphate coatings on Mg4Y alloy

    International Nuclear Information System (INIS)

    Calcium phosphates (CaPs) and silicon containing calcium phosphates (Si-CaPs) coatings on a biodegradable magnesium yttrium alloy (Mg4Y) were prepared by a sol–gel technique to improve the bioactivity of the alloy surface. The experimental results show that thick porous coatings comprised of nano-sized calcium phosphate particles can be prepared by heating the as dip coated substrates at 450 °C. The in vitro degradation results show that the coatings do not alter the degradation kinetics of the substrates significantly and the release of magnesium and yttrium ions at initial time points was very similar for both the coated and bare substrates. The cyto-compatibility studies using MC3T3-E1 osteoblasts show that the coated substrates were more bioactive than the uncoated substrates as the cells begin to grow and form a matrix on the coated substrates more easily than on the bare metal. These preliminary results collectively show the potential of use of sol–gel derived calcium phosphate coatings on magnesium based degradable scaffolds to improve their surface bioactivity.

  18. Reinforcement of freeze-dried chitosan scaffolds with multiphasic calcium phosphate short fibers.

    Science.gov (United States)

    Mohammadi, Zahra; Mesgar, Abdorreza Sheikh-Mehdi; Rasouli-Disfani, Fariba

    2016-08-01

    The composite scaffolds of the chitosan and multiphasic calcium phosphate (HW) short fibers were prepared by freeze drying and characterized by X-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM and FE-SEM). The mechanical properties of the scaffolds were assessed by compression test. The incorporation of HW fibers consisting three phases of hydroxyapatite (HA), beta-tricalcium phosphate (β-TCP) and calcium pyrophosphate (CPP) into the chitosan matrices was associated with an increase in pore size, density and compressive strength and modulus, and a decrease in porosity and swelling ratio of the scaffolds. The strongest composite scaffolds in this study with a chitosan: HW fibers weight ratio of 1:1 showed a mean porosity of 69% and a mean strength and modulus of 420kPa and 3.87MPa, respectively. The in vitro bioactivity of the composites was confirmed by the formation of a calcium phosphate rich layer on the surface of soaked scaffolds in simulated body fluid. The findings of this initial work indicate that the chitosan-multiphasic calcium phosphate short fibers may be a suitable material for bone scaffolding. PMID:27179144

  19. An efficient calcium phosphate nanoparticle-based nonviral vector for gene delivery

    Directory of Open Access Journals (Sweden)

    Liu YC

    2011-04-01

    Full Text Available Yachun Liu1,2,*, Tao Wang1,*, Fangli He1,*, Qian Liu1,*, Dexi Zhang2, Shuanglin Xiang1, Shengpei Su2, Jian Zhang11Key Laboratory of Protein Chemistry and Developmental Biology, Ministry of Education of China, College of Life Sciences; 2Key Laboratory of Chemical Biology and Traditional Chinese Medicine Research and Key Laboratory of Sustainable Resources Processing and Advanced Materials of Hunan Province, Ministry of Education of China, College of Chemistry and Chemical Engineering, Hunan Normal University, Changsha, Hunan, China*These authors contributed equally to this workBackground: Smaller nanoparticles facilitate the delivery of DNA into cells through endocytosis and improve transfection efficiency. The aim of this study was to determine whether protamine sulfate-coated calcium phosphate (PS-CaP could stabilize particle size and enhance transfection efficiency.Methods: pEGFP-C1 green fluorescence protein was employed as an indicator of transfection efficiency. Atomic force microscopy was used to evaluate the morphology and the size of the particles, and an MTT assay was introduced to detect cell viability and inhibition. The classical calcium phosphate method was used as the control.Results: Atomic force microscopy images showed that the PS-CaP were much smaller than classical calcium phosphate particles. In 293 FT, HEK 293, and NIH 3T3 cells, the transfection efficiency of PS-CaP was higher than for the classical calcium phosphate particles. The difference in efficiencies implies that the smaller nanoparticles may promote the delivery of DNA into cells through endocytosis and could improve transfection efficiency. In addition, PS-CaP could be used to transfect HEK 293 cells after one week of storage at 4°C with a lesser extent of efficiency loss compared with classical calcium phosphate, indicating that protamine sulfate may increase the stability of calcium phosphate nanoparticles. The cell viability inhibition assay indicated that

  20. Characterisation of magnesium potassium phosphate cements blended with fly ash and ground granulated blast furnace slag

    International Nuclear Information System (INIS)

    Magnesium potassium phosphate cements (MKPCs), blended with 50 wt.% fly ash (FA) or ground granulated blast furnace slag (GBFS) to reduce heat evolution, water demand and cost, were assessed using compressive strength, X-ray diffraction (XRD), scanning electron microscopy (SEM) and nuclear magnetic resonance (NMR) spectroscopy on 25Mg, 27Al, 29Si, 31P and 39K nuclei. We present the first definitive evidence that dissolution of the glassy aluminosilicate phases of both FA and GBFS occurred under the pH conditions of MKPC. In addition to the main binder phase, struvite-K, an amorphous orthophosphate phase was detected in FA/MKPC and GBFS/MKPC systems. It was postulated that an aluminium phosphate phase was formed, however, no significant Al–O–P interactions were identified. High-field NMR analysis of the GBFS/MKPC system indicated the potential formation of a potassium-aluminosilicate phase. This study demonstrates the need for further research on these binders, as both FA and GBFS are generally regarded as inert fillers within MKPC

  1. Characterisation of magnesium potassium phosphate cements blended with fly ash and ground granulated blast furnace slag

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, Laura J.; Bernal, Susan A.; Walling, Samuel A.; Corkhill, Claire L.; Provis, John L.; Hyatt, Neil C., E-mail: n.c.hyatt@sheffield.ac.uk

    2015-08-15

    Magnesium potassium phosphate cements (MKPCs), blended with 50 wt.% fly ash (FA) or ground granulated blast furnace slag (GBFS) to reduce heat evolution, water demand and cost, were assessed using compressive strength, X-ray diffraction (XRD), scanning electron microscopy (SEM) and nuclear magnetic resonance (NMR) spectroscopy on {sup 25}Mg, {sup 27}Al, {sup 29}Si, {sup 31}P and {sup 39}K nuclei. We present the first definitive evidence that dissolution of the glassy aluminosilicate phases of both FA and GBFS occurred under the pH conditions of MKPC. In addition to the main binder phase, struvite-K, an amorphous orthophosphate phase was detected in FA/MKPC and GBFS/MKPC systems. It was postulated that an aluminium phosphate phase was formed, however, no significant Al–O–P interactions were identified. High-field NMR analysis of the GBFS/MKPC system indicated the potential formation of a potassium-aluminosilicate phase. This study demonstrates the need for further research on these binders, as both FA and GBFS are generally regarded as inert fillers within MKPC.

  2. Use of industrial byproducts as alumina sources for the synthesis of calcium sulfoaluminate cements.

    Science.gov (United States)

    Pace, Maria Lucia; Telesca, Antonio; Marroccoli, Milena; Valenti, Gian Lorenzo

    2011-07-15

    Calcium sulfoaluminate (CSA) cements show some desirable environmentally friendly features that include the possibility of using several industrial byproducts as raw materials in their manufacturing process. Alumina powder, from the secondary aluminum manufacture, and anodization mud, from the production process of anodized aluminum, have proved to be suitable as partial or total substitutes for an expensive natural material like bauxite. CSA clinker generating raw mixtures, containing limestone, natural gypsum, bauxite, and/or one of the alumina-rich byproducts, were heated 2 h in a laboratory electric oven at temperatures ranging from 1150 to 1300 °C. Conversion of reactants into 4CaO·3Al(2)O(3)·SO(3) (the key component of CSA cements), evaluated using X-ray diffraction (XRD) analysis, increased with an increase of both burning temperature and byproduct concentration. When examined through differential thermogravimetric and XRD analyses, a synthetic CSA clinker (made from the raw mixture incorporating alumina powder as a total replacement of bauxite) mixed with 20% gypsum showed a hydration behavior almost similar to that of an industrial CSA cement containing the same amount of gypsum. PMID:21707122

  3. A construction of novel iron-foam-based calcium phosphate/chitosan coating biodegradable scaffold material.

    Science.gov (United States)

    Wen, Zhaohui; Zhang, Liming; Chen, Chao; Liu, Yibo; Wu, Changjun; Dai, Changsong

    2013-04-01

    Slow corrosion rate and poor bioactivity restrict iron-based implants in biomedical application. In this study, we design a new iron-foam-based calcium phosphate/chitosan coating biodegradable composites offering a priority mechanical and bioactive property for bone tissue engineering through electrophoretic deposition (EPD) followed by a conversion process into a phosphate buffer solution (PBS). Tensile test results showed that the mechanical property of iron foam could be regulated through altering the construction of polyurethane foam. The priority coatings were deposited from 40% nano hydroxyapatite (nHA)/ethanol suspension mixed with 60% nHA/chitosan-acetic acid aqueous solution. In vitro immersion test showed that oxidation-iron foam as the matrix decreased the amount of iron implanted and had not influence on the bioactivity of this implant, obviously. So, this method could also be a promising method for the preparation of a new calcium phosphate/chitosan coating on foam construction. PMID:23827538

  4. In Vitro Cytotoxicity of Calcium Silicate-Based Endodontic Cement as Root-End Filling Materials.

    Science.gov (United States)

    Küçükkaya, Selen; Görduysus, Mehmet Ömer; Zeybek, Naciye Dilara; Müftüoğlu, Sevda Fatma

    2016-01-01

    The aim of this study was to evaluate the cytotoxicity of three types of calcium silicate-based endodontic cement after different incubation periods with human periodontal ligament fibroblasts. Human periodontal ligament fibroblasts were cultured from extracted third molars and seeded in 96-well plates. MTA, calcium enriched mixture (CEM) cement, and Biodentine were prepared and added to culture insert plates which were immediately placed into 96-well plates containing cultured cells. After incubation periods of 24, 48, and 72 hours, cell viability was determined with WST-1 assay. Data were analysed statistically by ANOVA with repeated measures and Bonferroni tests. There was no significant difference in cell viability amongst the test materials after each incubation period (P > 0.05). MTA and CEM presented more than 90% cell viability after 24 and 48 hours of incubation and showed statistically significant decrease in cell viability after 72 hours of incubation (P Biodentine showed significantly less cell viability (73%) after 24 hours of incubation, whereas more than 90% cell viability was seen after 48 and 72 hours of incubation (P Biodentine and CEM can be considered as alternative materials for root-end surgery procedures. PMID:26904364

  5. Mechanistic study and modeling of radionuclides retention by the hydrated calcium silicates (HCS) of cements

    International Nuclear Information System (INIS)

    This work attempts to investigate the modelling of radioisotopes (Cs+, Pb2+, Eu3+) immobilization in cement matrix, in the frame of the design of engineered barrier of a deep radwaste repository. The model development concept consists of three major steps: - surface chemistry modelling of the calcium silicate hydrate CSH, used to simulate hydrated cement behaviour; - solid analysis of the batch sorption experiments: identification of the uptake mechanism; - both previous steps are used, with isotherm data, in the modelling of the radioisotopes immobilization in the CSH matrix. Final results: (all modelling are available for all the range of studied Ca/Si ratios and have been validated with predictive calculations). - A thermodynamic modelling of the CSH surface chemistry has been developed. The labile calcium and proton sorption constants on silanol sites (>SiOH) have been extracted. - Cs+ is sorbed on two sites. The silanol site (weak site) has a high site density (10 sites.nm-2), which accounts for the CSH unsaturation in high [CS+]. A strong site is also identified. - Pb2+ immobilization in CSH matrix is modelled with surface equilibria and solubility equilibrium. - Eu3+ fixation has been investigated with solid analysis: Site-Selective anti Time-Resolved Luminescence Spectroscopy, XPS and SEM-EDS. Eu3+ thus does not precipitate in CSH water but is sorbed on the CSH surface (high hydroxylated environment). Europium is also (minority site) inserted in the CSH framework. (author)

  6. X-AFm stabilization as a mechanism of bypassing conversion phenomena in calcium aluminate cements

    International Nuclear Information System (INIS)

    Phase conversion phenomena are often observed in calcium aluminate cements (CACs), when the water-rich hydrates (e.g., CAH10, C2AH8) formed at early ages, at temperatures ≤ 30 °C, expel water in time to form more compact, less water-rich structures (C3AH6). The phase conversions follow a path regulated by the thermodynamic stabilities (solubilities) of phases. Based on this premise, it is proposed that conversion phenomena in CACs can be bypassed by provoking the precipitation of phases more preferred than those typically encountered along the conversion pathway. Therefore, X-AFm formation (where in this case, X = NO3−) triggered by the sequential addition of calcium nitrate (Ca(NO3)2 = CN) additives is identified as a new means of bypassing conversion. A multi-method approach comprising X-ray diffraction (XRD), thermal analytics, and evaluations of the compressive strength is applied to correlate phase balances and properties of CAC systems cured at 25 °C and 45 °C. The results highlight the absence of the C3AH6 phase across all systems and the curing conditions considered, with enhanced strengths being noted, when sufficient quantities of CN are added. The experimental outcomes are supported by insights gained from thermodynamic calculations which highlight thermodynamic selectivity as a means of regulating and controlling the evolutions of solid phase balances using inorganic salts in CACs, and more generally in cementing material systems

  7. Conservative Management of Class 4 Invasive Cervical Root Resorption Using Calcium-enriched Mixture Cement.

    Science.gov (United States)

    Asgary, Saeed; Nosrat, Ali

    2016-08-01

    Class 4 invasive cervical root resorption (ICRR) presents a treatment dilemma in endodontics. The widely accepted treatment options for a class 4 ICRR are to leave these teeth untreated for as long as they are asymptomatic or extraction. This report presents a conservative approach for the management of class 4 ICRR. A 28-year-old woman was referred for root canal treatment of tooth #26. The patient had a history of orthodontic treatment. Radiographic evaluation showed class 4 ICRR that had perforated the root canal space, a radiolucent crestal bony defect, and a periapical lesion. Clinically, a deep (6-mm) probing area was found on the mesial side of the tooth that bled on probing. The tooth was sensitive to percussion. After the treatment options were discussed with the patient, she chose to save the tooth. After complete chemomechanical preparation of the root canal, the entire canal space and perforation area were filled with calcium-enriched mixture cement. No attempt was made to mechanically remove the resorptive lacuna. Twenty four months after treatment, the tooth was functional and asymptomatic, and probing was within normal limits (canal space with calcium-enriched mixture cement may be a viable treatment option for an otherwise non-treatable tooth with class 4 invasive cervical root resorption. PMID:27316319

  8. Kinetics and Mechanism of Adsorption of Phosphate on Fluorine-containing Calcium Silicate

    Institute of Scientific and Technical Information of China (English)

    ZHU Xinhua; ZHANG Zhao; SHEN Jun

    2016-01-01

    The nanowires-reticulated calcium silicate with a speciifc surface area more than 100 m2/g was prepared by a hydrothermal process using hydrated lime (Ca(OH)2, HL) and silica containing soluble lfuoride, which was a by-product of lfuorine industry, and the soluble lfuoride in raw silica was ifxed as CaSiF6 at the same time. The kinetic characteristics and mechanism of adsorbing phosphate by lfuorine-containing calcium silicate were investigated in the experiments of phosphorus (P) removal from aqueous solution. The results show that the prepared lfuorine-containing calcium silicate has excellent performance for adsorbing phosphate, the adsorption process appears to follow pseudo-second-order reaction kinetics and the process is mainly controlled by chemisorption. The product resulted from P adsorption is mainly composed of hydroxyapatite (HAP) and lfuorapatite (FAP), which are further used as adsorbents of heavy metal ion Cd2+ in aqueous solution and display excellent performance.

  9. Structure and properties of calcium iron phosphate glasses

    International Nuclear Information System (INIS)

    The structural properties of xCaO–(100 − x) (0.4Fe2O3–0.6P2O5) (x = 0, 10, 20, 30, 40, 50 mol%) glasses have been investigated by XRD, DTA, IR and Raman spectroscopy. XRD analysis has confirmed that the majority of samples are X-ray amorphous, and EDS analysis indicates that the glass matrix can accommodate ≈30 mol% CaO. IR and Raman spectra show that the glass structure consists predominantly of pyrophosphate (Q1) units. IR spectra indicate that the phosphate network is depolymerized with the addition of CaO content. The density and glass transition temperature (Tg) increase with increasing CaO content for the glasses. This behavior indicates that the addition of CaO improves the strength of the cross-links between the phosphate chains of the glass

  10. A novel biodegradable nicotinic acid/calcium phosphate composite coating on Mg–3Zn alloy

    International Nuclear Information System (INIS)

    A novel biodegradable composite coating is prepared to reduce the biodegradation rate of Mg–3Zn alloy. The Mg–3Zn substrate is first immersed into 0.02 mol L−1 nicotinic acid (NA) solution, named as vitamin B3, to obtain a pretreatment film, and then the electrodeposition of calcium phosphate coating with ultrasonic agitation is carried out on the NA pretreatment film to obtain a NA/calcium phosphate composite coating. Surface morphology is observed by scanning electron microscopy (SEM). Chemical composition is determined by X-ray diffraction (XRD) and EDX. Protection property of the coatings is evaluated by electrochemical tests. The biodegradable behavior is investigated by immersion tests. The results indicate that a thin but compact bottom layer can be obtained by NA pretreatment. The electrodeposition calcium phosphate coating consists of many flake particles and ultrasonic agitation can greatly improve the compactness of the coating. The composite coating is biodegradable and can reduce the biodegradation rate of Mg alloys in stimulated body fluid (SBF) for twenty times. The biodegradation process of the composite coating can be attributed to the gradual dissolution of the flake particles into chippings. - Highlights: ► NA/calcium phosphate composite coating is prepared to protect Mg–3Zn alloy implant. ► Nicotinic acid (vitamin B3) is available to obtain a protective bottom film. ► Ultrasonic agitation greatly improves the compactness of calcium phosphate coating. ► The composite coating can reduce the biodegradation rate of Mg–3Zn twenty times. ► The composite coating is biodegraded by the dissolution of flakes into chippings.

  11. A novel biodegradable nicotinic acid/calcium phosphate composite coating on Mg-3Zn alloy

    Energy Technology Data Exchange (ETDEWEB)

    Song, Yingwei, E-mail: ywsong@imr.ac.cn; Shan, Dayong; Han, En-Hou

    2013-01-01

    A novel biodegradable composite coating is prepared to reduce the biodegradation rate of Mg-3Zn alloy. The Mg-3Zn substrate is first immersed into 0.02 mol L{sup -1} nicotinic acid (NA) solution, named as vitamin B{sub 3}, to obtain a pretreatment film, and then the electrodeposition of calcium phosphate coating with ultrasonic agitation is carried out on the NA pretreatment film to obtain a NA/calcium phosphate composite coating. Surface morphology is observed by scanning electron microscopy (SEM). Chemical composition is determined by X-ray diffraction (XRD) and EDX. Protection property of the coatings is evaluated by electrochemical tests. The biodegradable behavior is investigated by immersion tests. The results indicate that a thin but compact bottom layer can be obtained by NA pretreatment. The electrodeposition calcium phosphate coating consists of many flake particles and ultrasonic agitation can greatly improve the compactness of the coating. The composite coating is biodegradable and can reduce the biodegradation rate of Mg alloys in stimulated body fluid (SBF) for twenty times. The biodegradation process of the composite coating can be attributed to the gradual dissolution of the flake particles into chippings. - Highlights: Black-Right-Pointing-Pointer NA/calcium phosphate composite coating is prepared to protect Mg-3Zn alloy implant. Black-Right-Pointing-Pointer Nicotinic acid (vitamin B{sub 3}) is available to obtain a protective bottom film. Black-Right-Pointing-Pointer Ultrasonic agitation greatly improves the compactness of calcium phosphate coating. Black-Right-Pointing-Pointer The composite coating can reduce the biodegradation rate of Mg-3Zn twenty times. Black-Right-Pointing-Pointer The composite coating is biodegraded by the dissolution of flakes into chippings.

  12. Phase stability of silver particles embedded calcium phosphate bioceramics

    Indian Academy of Sciences (India)

    Brajendra Singh; Samayendra Kumar; Naresh Saha; Bikramjit Basu; Rajeev Gupta

    2015-04-01

    In this paper, we report the compositional variation-dependent phase stability of hydroxyapatite (Ca10(PO4)6(OH)2) on doping with silver. The transformation of hydroxyapatite to (/) tricalcium phosphate phases during sintering has been explored using Raman spectroscopy and X-ray diffraction techniques. The optical absorption spectroscopy analysis reveals the presence of Ag+ ions at low doping levels. As the doping increases, abundance of Ag particles is enhanced.

  13. Histological evaluation of direct pulp capping by using of calcium hydroxide and octacalcium phosphate in cats dental pulp

    Directory of Open Access Journals (Sweden)

    Eshagh Ali Saberi

    2013-08-01

    Full Text Available   Background and Aims: The purpose of this study was to evaluate the tissue responses to octacalcium phosphate (OCP and calcium hydroxide (CH used as direct pulp capping (DPC materials in cat teeth.   Materials and Methods: 72 premolar teeth of 9 cats were selected and divided into 3 groups (Two experimental and one control group. After the cats had been anesthetized, the pulp were exposed and capped directly with OCP, CH or no capping material as control group. The cavities of all three groups were filled with Glass ionomer cement (GI. Histological evaluations were performed at two, four and eight weeks after pulp capping. After tissue preparation procedures, paraffin blocks were prepared. After preparation and staining of the sections, the relevant variables were measured by optical microscope. The results were analyzed using Mann-Whitney U and Chi-square tests ( α =0.05.   Results: Two weeks after pulp capping, all specimens in three groups showed mild to sever inflammation. The formation of hard tissue (dentinal bridge at in the exposed areas of the experimental groups was more noticeable for calcium hydroxide than that of octacalcium phosphate group. These differences were statistically significant (P<0.001. At four weeks, hard tissues were observed in both groups which were more evident for the CH group and there were statistically significant difference between two experimental groups (p0.05, but hard tissues continuity were better for in the OCP than that of the CH.   Conclusion: It seems that the formation of hard tissue in CH because of its porosities had a worse percentage in sealing of the pulp than the OCP .

  14. Comparison of three calcium phosphate bone graft substitutes from biomechanical, histological, and crystallographic perspectives using a rat posterolateral lumbar fusion model

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Ming-Hsien [Department of Biomedical Engineering, National Cheng Kung University, Tainan 701, Taiwan (China); Department of Orthopedics, Show-Chwan Memorial Hospital, Changhua 50544, Taiwan (China); Department of Orthopedic Surgery, Faculty of Medicine, National Yang-Ming University, Taipei 112, Taiwan (China); Lee, Pei-Yuan [Department of Biomedical Engineering, National Cheng Kung University, Tainan 701, Taiwan (China); Department of Orthopedics, Show-Chwan Memorial Hospital, Changhua 50544, Taiwan (China); Chen, Wen-Cheng, E-mail: wincheng0925@yahoo.com.tw [Department of Fiber and Composite Materials, College of Engineering, Feng Chia University, Taichung 40724, Taiwan (China); Hu, Jin-Jia, E-mail: jjhu@mail.ncku.edu.tw [Department of Biomedical Engineering, National Cheng Kung University, Tainan 701, Taiwan (China); Medical Device Innovation Center, National Cheng Kung University, Tainan 701, Taiwan (China)

    2014-12-01

    This study evaluated the effectiveness of three calcium phosphate bone graft substitutes with different chemical compositions on spinal fusion using a rat posterolateral lumbar fusion model. Specifically, two recently developed non-dispersive tetracalcium phosphate/dicalcium phosphate anhydrous-based calcium phosphate cements (CPCs), namely a CPC consisting of equimolar amounts of the two compounds (nd-CPC) and a CPC consisting of a two-fold greater amount of dicalcium phosphate anhydrous (DCP-rich CPC), were compared with a commercial calcium phosphate bone graft (c-CPG) consisting of hydroxyapatite (60%) and β-tricalcium phosphate (40%). Single-level posterolateral lumbar fusion was performed at the L4–L5 vertebrae in fifteen adult rats (n = 5 for each group). Spinal fusion was evaluated with radiographs, manual palpation, mechanical testing, micro-CT, and histology 8 weeks post-surgery. In particular, the crystallographic phases in the three substitutes were identified before and 8 weeks after their implantation. Manual palpation revealed stable constructs in nearly all of the spine specimens. The stiffness and bending load of fused spines in the two CPC groups were comparable to those in the c-CPG group. The radiographs specifically revealed implant resorption and bone remodeling in the DCP-rich CPC group. Analysis of 3D micro-CT images revealed that the bone volume ratio in the DCP-rich CPC group was significantly greater than those in the nd-CPC and c-CPG groups. Histology showed that the DCP-rich CPC group exhibited the highest degree of bone regeneration and osseointegration. Notably, DCP-rich CPC led to a pronounced phase transformation, generating the greatest amount of poorly crystalline apatite among the three groups, which together with adequate resorption may explain the aforementioned positive findings. We therefore conclude that of the bone graft substitutes considered, DCP-rich CPC has the greatest potential to be used in spinal fusion

  15. Comparison of three calcium phosphate bone graft substitutes from biomechanical, histological, and crystallographic perspectives using a rat posterolateral lumbar fusion model

    International Nuclear Information System (INIS)

    This study evaluated the effectiveness of three calcium phosphate bone graft substitutes with different chemical compositions on spinal fusion using a rat posterolateral lumbar fusion model. Specifically, two recently developed non-dispersive tetracalcium phosphate/dicalcium phosphate anhydrous-based calcium phosphate cements (CPCs), namely a CPC consisting of equimolar amounts of the two compounds (nd-CPC) and a CPC consisting of a two-fold greater amount of dicalcium phosphate anhydrous (DCP-rich CPC), were compared with a commercial calcium phosphate bone graft (c-CPG) consisting of hydroxyapatite (60%) and β-tricalcium phosphate (40%). Single-level posterolateral lumbar fusion was performed at the L4–L5 vertebrae in fifteen adult rats (n = 5 for each group). Spinal fusion was evaluated with radiographs, manual palpation, mechanical testing, micro-CT, and histology 8 weeks post-surgery. In particular, the crystallographic phases in the three substitutes were identified before and 8 weeks after their implantation. Manual palpation revealed stable constructs in nearly all of the spine specimens. The stiffness and bending load of fused spines in the two CPC groups were comparable to those in the c-CPG group. The radiographs specifically revealed implant resorption and bone remodeling in the DCP-rich CPC group. Analysis of 3D micro-CT images revealed that the bone volume ratio in the DCP-rich CPC group was significantly greater than those in the nd-CPC and c-CPG groups. Histology showed that the DCP-rich CPC group exhibited the highest degree of bone regeneration and osseointegration. Notably, DCP-rich CPC led to a pronounced phase transformation, generating the greatest amount of poorly crystalline apatite among the three groups, which together with adequate resorption may explain the aforementioned positive findings. We therefore conclude that of the bone graft substitutes considered, DCP-rich CPC has the greatest potential to be used in spinal fusion

  16. Influence of core-finishing intervals on tensile strength of cast posts-and-cores luted with zinc phosphate cement

    Directory of Open Access Journals (Sweden)

    Michele Andrea Lopes Iglesias

    2012-08-01

    Full Text Available The core finishing of cast posts-and-cores after luting is routine in dental practice. However, the effects of the vibrations produced by the rotary cutting instruments over the luting cements are not well-documented. This study evaluated the influence of the time intervals that elapsed between the cementation and the core-finishing procedures on the tensile strength of cast posts-and-cores luted with zinc phosphate cement. Forty-eight bovine incisor roots were selected, endodontically treated, and divided into four groups (n = 12: GA, control (without finishing; GB, GC, and GD, subjected to finishing at 20 minutes, 60 minutes, and 24 hours after cementation, respectively. Root canals were molded, and the resin patterns were cast in copper-aluminum alloy. Cast posts-and-cores were luted with zinc phosphate cement, and the core-finishing procedures were applied according to the groups. The tensile tests were performed at a crosshead speed of 0.5 mm/min for all groups, 24 hours after the core-finishing procedures. The data were subjected to one-way analysis of variance (ANOVA and Tukey's test (α = 0.05. No significant differences were observed in the tensile strengths between the control and experimental groups, regardless of the time interval that elapsed between the luting and finishing steps. Within the limitations of the present study, it was demonstrated that the core-finishing procedures and time intervals that elapsed after luting did not appear to affect the retention of cast posts-and-cores when zinc phosphate cement was used.

  17. Heat treatment of pre-hydrolyzed silane increases adhesion of phosphate monomer-based resin cement to glass ceramic

    OpenAIRE

    de Carvalho, Rodrigo Furtado; Caroline COTES; Kimpara, Estevão Tomomitsu; Leite, Fabíola Pessoa Pereira; Özcan, Mutlu

    2015-01-01

    This study evaluated the influence of different forms of heat treatment on a pre-hydrolyzed silane to improve the adhesion of phosphate monomer-based (MDP) resin cement to glass ceramic. Resin and feldspathic ceramic blocks (n=48, n=6 for bond test, n=2 for microscopy) were randomly divided into 6 groups and subject to surface treatments: G1: Hydrofluoric acid (HF) 9.6% for 20 s + Silane + MDP resin cement (Panavia F); G2: HF 9.6% for 20 s + Silane + Heat Treatment (oven) + Panavia F; G3: Sil...

  18. Dynamic changes in calcium and phosphate plasma concentrations in the patients on peritoneal dialysis

    Directory of Open Access Journals (Sweden)

    Jovanović Nataša

    2006-01-01

    Full Text Available Background/Aim. The disturbances of active forms of vitamin D synthesis and disturbances in calcium and posphate metabolism develop early in chronic renal failure, when creatinine clearance is about 30 ml/min. Chronic hemodialysis and peritoneal dialysis only partially correct the biochemical environment of patients on chronic renal replacement therapy because of end-stage renal disease. These dialysis modalities can’t significantly affect the endocrine disturbances of chronic renal failure and they have minimal modulatory effect. The management of disturbed calcium (Ca and phosphate (P metabolism and the maintainance of Ca × P product below 4.4 mmol/l thanks to the use of dialysate solutions with the appropriate calcium concentration and the careful dosage of phosphate binders, calcium and active vitamin D metabolits, are extremely important for the prevention of renal osteodystrophy, secondary hyperparathyroidism as well as low-bone turnover disease. The aim of the study was to analyze the plasma levels of calcium, phosphate, albumin, alkaline phosphatase and parathormon (PTH in 58 patients who were treated with continuous ambulatory peritoneal dialysis (CAPD from March to August 2003. The use of phosphate binders and the substitution with active vitamin D metabolits were also analyzed. Methods. We examined 58 patients, 30 males and 28 female, mean-age 52 years (range, 26-78 years, affected by end-stage renal disease of the different leading cause. The average time on peritoneal dialysis program was 20 months (2-66 months. Most of the patients were treated by CAPD, while only few of them performed automatic, cyclic or intermittent peritoneal dialysis. Most of the patients used a dialysate with 1.75 mmol/l calcium concentration. Results. The study showed that our patients on chronic CAPD program during several months had normal calcemia, phosphatemia and the level of alkaline phosphatase, and that they had Ca × P product in the recommended

  19. Characterization of high-calcium fly ash and its influence on ettringite formation in portland cement pastes

    Science.gov (United States)

    Tishmack, Jody Kathleen

    High-calcium Class C fly ashes derived from Powder River Basin coal are currently used as supplementary cementing materials in portland cement concrete. These fly ashes tend to contain significant amounts of sulfur, calcium, and aluminum, thus they are potential sources of ettringite. Characterization of six high-calcium fly ashes originating from Powder River Basin coal have been carried out. The hydration products formed in pastes made from fly ash and water were investigated. The principal phases produced at room temperature were ettringite, monosulfate, and stratlingite. The relative amounts formed varied with the specific fly ash. Removal of the soluble crystalline sulfur bearing minerals indicated that approximately a third of the sulfur is located in the fly ash glass. Pore solution analyses indicated that sulfur concentrations increased at later ages. Three fly ashes were selected for further study based on their ability to form ettringite. Portland cement-fly ash pastes made with the selected fly ashes were investigated to evaluate ettringite and monosulfate formation. Each of the fly ashes were mixed with four different types of portland cements (Type I, I/II, II, and III) as well as three different Type I cements exhibiting a range of C3A and sulfate contents. The pastes had 25% or 35% fly ash by total weight of solids and a water:cement-fly ash ratio of 0.45. The samples were placed in a curing room (R.H. = 100, 23°C) and were then analyzed at various ages by x-ray diffraction (XRD) and differential scanning calorimetry (DSC) to determine the principal hydration products. The hydration products identified by XRD were portlandite, ettringite (an AFt phase), monosulfate, and generally smaller amounts of hemicarboaluminate and monocarboaluminate (all AFm phases). Although the amount of ettringite formed varied with the individual cement, only a modest correlation with cement sulfate content and no correlation with cement C3A content was observed. DSC

  20. Calcium Carbonate versus Sevelamer Hydrochloride as Phosphate Binders after Long-Term Disease Progression in 5/6 Nephrectomized Rats

    Directory of Open Access Journals (Sweden)

    Suvi Törmänen

    2014-01-01

    Full Text Available Our aim was to compare the effects of calcium carbonate and sevelamer-HCl treatments on calcium-phosphate metabolism and renal function in 5/6 nephrectomized (NX rats so that long-term disease progression preceded the treatment. After 15-week progression, calcium carbonate (3.0%, sevelamer-HCl (3.0%, or control diets (0.3% calcium were given for 9 weeks. Subtotal nephrectomy reduced creatinine clearance (−40%, plasma calcidiol (−25%, and calcitriol (−70% and increased phosphate (+37%, parathyroid hormone (PTH (11-fold, and fibroblast growth factor-23 (FGF-23 (4-fold. In NX rats, calcium carbonate diet increased plasma (+20% and urinary calcium (6-fold, reduced plasma phosphate (−50% and calcidiol (−30%, decreased creatinine clearance (−35% and FGF 23 (−85%, and suppressed PTH without influencing blood pH. In NX rats, sevelamer-HCl increased urinary calcium (4-fold and decreased creatinine clearance (−45%, PTH (−75%, blood pH (by 0.20 units, plasma calcidiol (−40%, and calcitriol (−65%. Plasma phosphate and FGF-23 were unchanged. In conclusion, when initiated after long-term progression of experimental renal insufficiency, calcium carbonate diet reduced plasma phosphate and FGF-23 while sevelamer-HCl did not. The former induced hypercalcemia, the latter induced acidosis, while both treatments reduced vitamin D metabolites and deteriorated renal function. Thus, delayed initiation influences the effects of these phosphate binders in remnant kidney rats.

  1. Effect of Fluoride, Casein Phosphopeptide–Amorphous Calcium Phosphate and Casein Phosphopeptide–Amorphous Calcium Phosphate Fluoride on Enamel Surface Microhardness After Microabrasion: An In Vitro Study

    Directory of Open Access Journals (Sweden)

    Ghazaleh Ahmadi Zenouz

    2016-03-01

    Full Text Available Objectives: This study aimed to assess the effect of applying casein phosphopeptide–amorphous calcium phosphate (CPP-ACP paste, casein phosphopeptide–amorphous calcium phosphate fluoride (CPP-ACPF paste and sodium fluoride gel on surface microhardness of enamel after microabrasion.Materials and Methods: Thirty freshly extracted human premolars were selected. All samples were subjected to hardness indentations made with the Vickers hardness machine and the average value was recorded as the initial surface microhardness. The specimens were then randomly divided into three groups (n=10 of CPP-ACPF, fluoride and CPP-ACP. The teeth were micro-abraded with Opalustre. Microhardness test was performed to assess the post-abrasion hardness. Three remineralization modalities were performed on samples of each group. The enamel surface microhardness measurements were performed. To compare the difference between groups, the rehardening and softening values were defined. One-way ANOVA and Tukey’s post hoc test at a significance level of 5% were used for statistical analysis.Results: The mean microhardness value (MMV had a significant decrease after microabrasion from baseline. The MMV had a significant increase after remineralization in all groups. The MMV of CPP-ACPF group was significantly more than that of fluoride group (P=0.027. The rehardening value of fluoride group was significantly more than that of other groups (P<0.001.Conclusion: All the remineralizing agents were effective for rehardening the enamel after microabrasion. The CPP-ACP and CPP-ACPF pastes are effective, but to a lesser extent than neutral sodium fluoride gel in remineralizing enamel surface. Incorporation of fluoride to CPP-ACP formulation does not provide any additional remineralizing potential.Keywords: Casein phosphopeptide-amorphous calcium phosphate nanocomplex; Enamel Microabrasion; Hardness; Sodium Fluoride

  2. Synthesis and characterization of calcium phosphate/collagen biocomposites doped with Zn{sup 2+}

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Maria Helena [Department of Dentistry, Federal University of Vales do Jequitinhonha e Mucuri-UFVJM, mailbox 38, Zip:39100-000, Diamantina, MG (Brazil)], E-mail: mariahelena.santos@gmail.com; Dias Heneine, Luis Guilherme [Department of Health Science, Ezequiel Dias Foundation, Belo Horizonte, MG (Brazil); Sander Mansur, Herman [Department of Metallurgical and Materials Engineering, Federal University of Minas Gerais, Belo Horizonte, MG (Brazil)

    2008-05-01

    Composites were developed using calcium phosphate (CaP)/collagen (COL) doped with Zn{sup +2} to attempt the materials association with adequate properties for biological applications in the recovery of the bone tissue by trauma or pathogenies. Hydroxyapatite (HAP) and hydroxyapatite-{beta}tricalcium phosphate (HAP{beta}TCP) were synthesized and doped with zinc nitrate. High purity grade type I collagen was extracted and purified from bovine pericardium. CaP doped and undoped with Zn{sup +2} were produced with COL and the composites were developed using a simple mixture process. All samples were characterized by Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR) and X-ray diffraction analysis (XRD. In addition, biocompatibility and cell viability were assessed by MTT assay (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide) using osteoblast cell culture. The results have indicated that both morphological and structural features and chemical composition of the composites were very similar to their precursors, collagen and calcium phosphate components. Also, the biocomposites presented a homogeneous aspect with the calcium phosphate particles aggregated to the collagen fibers. The biological evaluation of the composites in vitro showed cellular viability, presenting proliferation of the osteoblasts compared to the control cells (P < 0.05). The composites showed appropriate physical and biological properties creating more biologically active scaffolds that may support bone growth. Therefore, the novel developed biocomposites have high potential to be used for rebuilding small lesions in bone tissue engineering.

  3. Structural characterization of anion-calcium-humate complexes in phosphate-based fertilizers.

    Science.gov (United States)

    Baigorri, Roberto; Urrutia, Oscar; Erro, Javier; Mandado, Marcos; Pérez-Juste, Ignacio; Garcia-Mina, José María

    2013-07-01

    Fertilizers based on phosphate-metal-humate complexes are a new family of compounds that represents a more sustainable and bioavailable phosphorus source. The characterization of this type of complex by using solid (31)P NMR in several fertilizers, based on single superphosphate (SSP) and triple superphosphate (TSP) matrices, yielded surprising and unexpected trends in the intensity and fine structure of the (31)P NMR peaks. Computational chemistry methods allowed the characterization of phosphate-calcium-humate complexes in both SSP and TSP matrices, but also predicted the formation of a stable sulfate-calcium-humate complex in the SSP fertilizers, which has not been described previously. The stability of this complex has been confirmed by using ultrafiltration techniques. Preference towards the humic substance for the sulfate-metal phase in SSP allowed the explanation of the opposing trends that were observed in the experimental (31)P NMR spectra of SSP and TSP samples. Additionally, computational chemistry has provided an assignment of the (31)P NMR signals to different phosphate ligands as well as valuable information about the relative strength of the phosphate-calcium interactions within the crystals. PMID:23670945

  4. Synthesis and characterization of calcium phosphate/collagen biocomposites doped with Zn2+

    International Nuclear Information System (INIS)

    Composites were developed using calcium phosphate (CaP)/collagen (COL) doped with Zn+2 to attempt the materials association with adequate properties for biological applications in the recovery of the bone tissue by trauma or pathogenies. Hydroxyapatite (HAP) and hydroxyapatite-βtricalcium phosphate (HAPβTCP) were synthesized and doped with zinc nitrate. High purity grade type I collagen was extracted and purified from bovine pericardium. CaP doped and undoped with Zn+2 were produced with COL and the composites were developed using a simple mixture process. All samples were characterized by Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR) and X-ray diffraction analysis (XRD. In addition, biocompatibility and cell viability were assessed by MTT assay (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide) using osteoblast cell culture. The results have indicated that both morphological and structural features and chemical composition of the composites were very similar to their precursors, collagen and calcium phosphate components. Also, the biocomposites presented a homogeneous aspect with the calcium phosphate particles aggregated to the collagen fibers. The biological evaluation of the composites in vitro showed cellular viability, presenting proliferation of the osteoblasts compared to the control cells (P < 0.05). The composites showed appropriate physical and biological properties creating more biologically active scaffolds that may support bone growth. Therefore, the novel developed biocomposites have high potential to be used for rebuilding small lesions in bone tissue engineering

  5. Hereditary deafness with hydrops and anomalous calcium phosphate deposits

    Energy Technology Data Exchange (ETDEWEB)

    Johnsson, L.G.; Rouse, R.C.; Hawkins, J.E. Jr.; Kingsley, T.C.; Wright, C.G.

    1981-11-01

    The temporal bones from a 58-year-old white woman who had had hereditary congenital deafness were examined with the techniques of microdissection and surface preparations followed by sectioning of the modiolus. There was bilateral, almost total sensorineural degeneration, which also involved the saccule. The degeneration of the distal processes of the cochlear neurons in the osseous spiral lamina was almost complete, whereas numerous ganglion cells and proximal processes remained in the modiolus and the internal auditory canal. Severe cochleo-saccular hydrops was present in the left ear with Reissner's membrane bulging into the horizontal canal. X-ray diffraction and electron probe analysis were used to study the abnormal crystalline deposits in both ears. On the left side the saccular otoconia were composed of calcite, but the utricular macula was covered by a crust of apatite spherulites. More apatite occurred around the maculae and in the scala media. The cupulae were composed of apatite and octacalcium phosphate. On the right side the utricular otoconia were of normal calcite, but there was a deposit of apatite on the macula sacculi. The upper part of the scala media was completely filled by a deposit of apatite and octacalcium phosphate.

  6. Hereditary deafness with hydrops and anomalous calcium phosphate deposits

    International Nuclear Information System (INIS)

    The temporal bones from a 58-year-old white woman who had had hereditary congenital deafness were examined with the techniques of microdissection and surface preparations followed by sectioning of the modiolus. There was bilateral, almost total sensorineural degeneration, which also involved the saccule. The degeneration of the distal processes of the cochlear neurons in the osseous spiral lamina was almost complete, whereas numerous ganglion cells and proximal processes remained in the modiolus and the internal auditory canal. Severe cochleo-saccular hydrops was present in the left ear with Reissner's membrane bulging into the horizontal canal. X-ray diffraction and electron probe analysis were used to study the abnormal crystalline deposits in both ears. On the left side the saccular otoconia were composed of calcite, but the utricular macula was covered by a crust of apatite spherulites. More apatite occurred around the maculae and in the scala media. The cupulae were composed of apatite and octacalcium phosphate. On the right side the utricular otoconia were of normal calcite, but there was a deposit of apatite on the macula sacculi. The upper part of the scala media was completely filled by a deposit of apatite and octacalcium phosphate

  7. Investigation into the role of NaOH and calcium ions in the synthesis of calcium phosphate nanoshells

    Directory of Open Access Journals (Sweden)

    C. H. Yeo

    2012-03-01

    Full Text Available Calcium phosphate (CaP nanoshells were prepared using negatively charged liposomes (1,2-dioleoyl-sn-glycero-3-phosphate sodium salt (DOPA as a template by base titration synthesis at various concentrations of NaOH and calcium ions. The elemental composition, morphology, particle size, particle size distribution and zeta potential of the products were determined via various characterisation techniques, such as energy-dispersive X-ray spectrometry (EDX, transmission electron microscopy (TEM, dynamic light scattering (DLS, laser Doppler velocimetry (LDV and Fourier transform infrared spectroscopy (FTIR. The best results showed that stable spherical CaP nanoshells with a mean particle size of 197.5 ± 5.8 nm and a zeta potential of -34.5 ± 0.6 mV were successfully formed when 0.100 M sodium hydroxide (NaOH and 0.100 M calcium ions were used. Moreover, an optimal pH of 10.52 and a final Ca/P molar ratio of 0.97 were achieved under these conditions.

  8. Synthesis of some calcium phosphate crystals using the useful biomass for immobilization of microorganisms

    Science.gov (United States)

    Kohiruimaki, T.

    2011-10-01

    Three sources of biomass generated by primary industry were used as the raw material for the synthesis of calcium phosphate crystals. Phosphoric acid was extracted from burned rice chaff using a 30% nitric acid solution, while scallop shells and gypsum of plasterboard were used as calcium sources. The calcium phosphate crystals were synthesized by a method involving homogeneous precipitation, and the relationship between the composition and shape of the crystals and the pH at the time of the precipitation was investigated. Monetite crystals in a petal form with a diameter ranging from 0.1 to 2 μm were precipitated at pH 2.0, while granular apatite crystals with a mean diameter of 1 μm were precipitated at pH 6.0. We also investigated the ability of the synthesized calcium phosphate crystals to immobilize lactic acid bacteria for practical use in industrial bioreactor. It was determined that monetite crystals with a diameter of 2 μm had the highest ability to fix lactic acid bacteria. The population of lactic acid bacteria was estimated to exceed 1,300 bacteria per crystal surface of 50 μm2 suggesting that these crystals may be of practical use in industrial fermenters.

  9. Synthesis of some calcium phosphate crystals using the useful biomass for immobilization of microorganisms

    Energy Technology Data Exchange (ETDEWEB)

    Kohiruimaki, T, E-mail: kohi@hi-tech.ac.jp [Department of Technology, Hachinohe Institute of Technology, 88-1 Myo-oobiraki, Hachinohe-shi 031-8501 (Japan)

    2011-10-29

    Three sources of biomass generated by primary industry were used as the raw material for the synthesis of calcium phosphate crystals. Phosphoric acid was extracted from burned rice chaff using a 30% nitric acid solution, while scallop shells and gypsum of plasterboard were used as calcium sources. The calcium phosphate crystals were synthesized by a method involving homogeneous precipitation, and the relationship between the composition and shape of the crystals and the pH at the time of the precipitation was investigated. Monetite crystals in a petal form with a diameter ranging from 0.1 to 2 {mu}m were precipitated at pH 2.0, while granular apatite crystals with a mean diameter of 1 {mu}m were precipitated at pH 6.0. We also investigated the ability of the synthesized calcium phosphate crystals to immobilize lactic acid bacteria for practical use in industrial bioreactor. It was determined that monetite crystals with a diameter of 2 {mu}m had the highest ability to fix lactic acid bacteria. The population of lactic acid bacteria was estimated to exceed 1,300 bacteria per crystal surface of 50 {mu}m{sup 2} suggesting that these crystals may be of practical use in industrial fermenters.

  10. Preparation and Characterization of Injectable Brushite Filled-Poly (Methyl Methacrylate) Bone Cement

    OpenAIRE

    Lucas C. Rodriguez; Jonathan Chari; Shant Aghyarian; Gindri, Izabelle M.; Victor Kosmopoulos; Rodrigues, Danieli C.

    2014-01-01

    Powder-liquid poly (methyl methacrylate) (PMMA) bone cements are widely utilized for augmentation of bone fractures and fixation of orthopedic implants. These cements typically have an abundance of beneficial qualities, however their lack of bioactivity allows for continued development. To enhance osseointegration and bioactivity, calcium phosphate cements prepared with hydroxyapatite, brushite or tricalcium phosphates have been introduced with rather unsuccessful results due to increased cem...

  11. Magnesium substitution in the structure of orthopedic nanoparticles: A comparison between amorphous magnesium phosphates, calcium magnesium phosphates, and hydroxyapatites

    Energy Technology Data Exchange (ETDEWEB)

    Nabiyouni, Maryam, E-mail: maryam.nabiyouni@rockets.utoledo.edu [Department of Bioengineering, University of Toledo, Toledo, OH (United States); Ren, Yufu [Department of Mechanical, Industrial and Manufacturing Engineering, University of Toledo, Toledo, OH (United States); Bhaduri, Sarit B. [Department of Mechanical, Industrial and Manufacturing Engineering, University of Toledo, Toledo, OH (United States); Department of Surgery (Dentistry), University of Toledo, Toledo, OH (United States)

    2015-07-01

    As biocompatible materials, magnesium phosphates have received a lot of attention for orthopedic applications. During the last decade multiple studies have shown advantages for magnesium phosphate such as lack of cytotoxicity, biocompatibility, strong mechanical properties, and high biodegradability. The present study investigates the role of Mg{sup +2} and Ca{sup +2} ions in the structure of magnesium phosphate and calcium phosphate nanoparticles. To directly compare the effect of Mg{sup +2} and Ca{sup +2} ions on structure of nanoparticles and their biological behavior, three groups of nanoparticles including amorphous magnesium phosphates (AMPs) which release Mg{sup +2}, calcium magnesium phosphates (CMPs) which release Mg{sup +2} and Ca{sup +2}, and hydroxyapatites (HAs) which release Ca{sup +2} were studied. SEM, TEM, XRD, and FTIR were used to evaluate the morphology, crystallinity, and chemical properties of the particles. AMP particles were homogeneous nanospheres, whereas CMPs were combinations of heterogeneous nanorods and nanospheres, and HAs which contained heterogeneous nanosphere particles. Cell compatibility was monitored in all groups to determine the cytotoxicity effect of particles on studied MC3T3-E1 preosteoblasts. AMPs showed significantly higher attachment rate than the HAs after 1 day and both AMPs and CMPs showed significantly higher proliferation rate when compared to HAs after 7 days. Gene expression level of osteoblastic markers ALP, COL I, OCN, OPN, RUNX2 were monitored and they were normalized to GAPDH housekeeping gene. Beta actin expression level was monitored as the second housekeeping gene to confirm the accuracy of results. In general, AMPs and CMPs showed higher expression level of osteoblastic genes after 7 days which can further confirm the stimulating role of Mg{sup +}2 and Ca{sup +2} ions in increasing the proliferation rate, differentiation, and mineralization of MC3T3-E1 preosteoblasts. - Highlights: • Role of Mg{sup 2

  12. Modulating calcium phosphate formation using CO2 laser engineering of a polymeric material

    International Nuclear Information System (INIS)

    The use of simulated body fluid (SBF) is widely used as a screening technique to assess the ability of materials to promote calcium phosphate formation. This paper details the use of CO2 laser surface treatment of nylon® 6,6 to modulate calcium phosphate formation following immersion in SBF for 14 days. Through white light interferometry (WLI) it was determined that the laser surface processing gave rise to maximum Ra and Sa parameters of 1.3 and 4.4 μm, respectively. The use of X-ray photoelectron spectroscopy (XPS) enabled a maximum increase in surface oxygen content of 5.6%at. to be identified. The laser-induced surface modifications gave rise to a modulation in the wettability characteristics such that the contact angle, θ, decreased for the whole area processed samples, as expected, and increased for the patterned samples. The increase in θ can be attributed to a transition in wetting nature to a mixed-state wetting regime. It was seen for all samples that calcium phosphate formed on each surface following 14 days. The largest increase in mass, Δg, owed to calcium phosphate formation, was brought about by the whole area processed sample irradiated with a fluence of 51 J cm−2. No correlation between the calcium phosphate formation and the laser patterned surface properties was determined due to the likely affect of the mixed-state wetting regime. Strong correlations between θ, the surface energy parameters and the calcium phosphate formation for the whole area processed samples allow one to realize the potential for this surface treatment technique in predicting the bone forming ability of laser processed materials. - Highlights: ► Surface modifications brought about a modulation in the wetting of nylon 6,6. ► An increase in θ can be attributed to a mixed-state wetting regime. ► Laser surface treatment modulated the ability to promote apatite formation. ► Mixed-state wetting regime affected the promotion of uniform apatite formation. ► Method

  13. Effect of carbonate and phosphate ratios on the transformation of calcium orthophosphates

    International Nuclear Information System (INIS)

    Graphical abstract: Complexes among phosphate, carbonate and calcium have been prepared via a facile hydrothermal route. The synthesized product at the low (0.15) and the high (1.8) molar ratio of PO43−/CO32− is calcium phosphate hydrate and hydroxylapatite (HAp), respectively. Molar ratios of PO43−/CO32− are effective on the reduction of carbonate activity during the crystallization of HAp. - Highlights: • Formation of different complexes from CO32−, PO43− and Ca2+ solutions at 60 °C. • Molar ratios of PO43−/CO32 cause changes in phase and size of synthesized products. • Addition of PO43 inhibited the activity of CO32− during bound with Ca2+. • The phase transformation was completed, when CO32− peaks disappeared in FTIR. • PO43−, CO32− and Ca2+ distributed heterogeneously on the surface of precipitation. - Abstract: Complexes among phosphate, carbonate and calcium have been synthesized by a designed hydrothermal method. Effects of carbonate and phosphate ratios on the transformation of calcium-orthophosphates were investigated. With X-ray diffraction measurement the synthesized product at the low (0.15) and the high (1.8) molar ratio of PO43−/CO32− is calcium phosphate hydrate at pH 9.0, and hydroxylapatite (HAp) at pH 8.0, respectively. Fourier transform infrared spectroscopy of product at the high ratio (1.8) of PO43−/CO32− shows that the CO32− peaks disappear, and the strong peaks at 1412 and 1460 cm−1 are assigned to the vibrations of PO43− in HAp. 31P nuclear magnetic resonance spectra of products at the low (0.15–0.6) to the high (1.2–1.8) ratios of PO43−/CO32− are obtained at 2.9 and 2.7 ppm, respectively. Molar ratios of PO43−/CO32− are effective on the reduction of carbonate activity during the formation and infiltration events of calcium-phosphate surface precipitates, and are subsequently enclosed during HAp formation

  14. A new acoustic method to determine the setting time of calcium sulfate bone cement mixed with antibiotics

    International Nuclear Information System (INIS)

    A new method is described which can be used to determine the setting times of small amounts of high value bone cements. The test was developed to measure how the setting times of a commercially available synthetic calcium sulfate cement (Stimulan, Biocomposites, UK) in two forms (standard and Rapid Cure) varies with the addition of clinically relevant antibiotics. The importance of being able to accurately quantify these setting times is discussed. The results demonstrate that this new method, which is shown to correlate to the Vicat needle, gives reliable and repeatable data with additional benefits expressed in the article. The majority of antibiotics mixed were found to retard the setting reaction of the calcium sulfate cement. (paper)

  15. In vitro degradation of electrodeposited calcium phosphate coatings by osteoclast-like cells

    International Nuclear Information System (INIS)

    The aim of this study is to investigate the in vitro degradation of electrolytically deposited calcium phosphate coatings in the presence of osteoclast-like cells. Titanium alloy plates electrolytically coated with calcium phosphate with or without chitosan were incubated with RAW264.7 cells for 14 days. The TRAP activity was measured and the cell attachment and proliferation capacity were analyzed. The calcium ion concentrations in the culture medium before and after incubation were calculated. Both coatings were observed with scanning electron microscopy and characterized through an x-ray diffractometer and Fourier transform infrared spectrum. The RAW264.7 cells differentiated into TRAP-positive osteoclast-like cells on both coatings after 7 days. Although presenting different cell attachment pattern, the RAW264.7 cells demonstrated the similar TRAP activity and proliferation capacity. It was found that the calcium ion concentrations in the medium decreased at the beginning, but increased after 11 and 14 days. The chitosan containing coatings had higher Ca2+ concentration in the medium compared to that without chitosan. Besides, the incubation of coatings with cells induced higher calcium ion concentrations than those without cells at day 11 and day 14. Despite the structural changes of dissolution pits and osteoclastic resorption lacunae present on both coatings, the x-ray diffractometer and Fourier transform infrared spectrum showed few alternations in their chemical compositions. Both electrodeposited calcium phosphate coatings can be resorbed by osteoclast-like RAW264.7 cells and dissolved in the culture medium in vitro. The degradation brings little change to the chemical compositions of both coatings. (paper)

  16. Interaction between hydroxypropyl methylcellulose and biphasic calcium phosphate after steam sterilisation: capillary gas chromatography studies.

    OpenAIRE

    Bourges, Xavier; Schmitt, Michel; Amouriq, Yves; Daculsi, Guy; Legeay, Gilbert; Pierre WEISS

    2001-01-01

    The purpose of this study was to check the chemical stability of an injectable bone substitute (IBS) composed of a 50/50 w/w mixture of a 2.92% hydroxypropyl methylcellulose (HPMC) solution in deionised water containing biphasic calcium phosphate (BCP) granules (60% hydroxyapatite/40% β-tricalcium phosphate w/w). After separation of the organic and mineral phases, capillary gas chromatography (GC) was used to study the possible modification of HPMC due to the contact with BCP granules followi...

  17. Calcium thorium phosphate (Whitlockite-type mineral). Synthesis and structure refinement

    International Nuclear Information System (INIS)

    The crystal structure of a new calcium thorium phosphate has been refined by the full-profile Rietveld method using X-ray powder diffraction data. The sample has been synthesized by the sol-gel technique. The phosphate has been identified by X-ray powder diffraction and IR spectroscopy. The refined composition is represented by the formula Ca10.26Th0.12(PO4)7. The CaOn and PO4 polyhedra are distorted compared to the corresponding polyhedra in the basic compound β-Ca3(PO4)2.

  18. Identification and quantitive analysis of calcium phosphate microparticles in intestinal tissue by nuclear microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Morilla, Inmaculada [Advanced Technology Institute, University of Surrey, Guildford GU2 7XH (United Kingdom)]. E-mail: i.gomez-morilla@surrey.ac.uk; Thoree, Vinay [Gastrointestinal Laboratory, Rayne Institute, St. Thomas' Hospital, London SE1 7EH (United Kingdom); Powell, Jonathan J. [MRC Human Nutrition Research, Elsie Widdowson Laboratory, Fulbourn Road, Cambridge CB1 9NL (United Kingdom); Kirkby, Karen J. [Advanced Technology Institute, University of Surrey, Guildford GU2 7XH (United Kingdom); Grime, Geoffrey W. [Department of Physics, University of Surrey, GU2 7XH (United Kingdom)

    2006-08-15

    Microscopic particles (0.5-2 {mu}m diameter), rich in calcium and phosphorus, are found in the lumen of the mid-distal gut of all mammals investigated, including humans, and these may play a role in immuno-surveillance and immune regulation of antigens from food and symbiotic bacteria that are contained in the gut. Whether these particles can cross in to tissue of the intestinal mucosa is unclear. If so, characterising their morphology and chemical composition is an important task in elucidating their function. The analysis of calcium phosphate in biological tissues has been approached in several ways including optical microscopy, scanning electron microscopy and, most recently in this work, with nuclear microscopy. In this paper, we describe the use of microPIXE and microRBS to locate these particles and to determine, accurately, the ratio of phosphorus to calcium using the information on sample thickness obtained from RBS to allow the PIXE ratios to be corrected. A commercial sample of hydroxy apatite was used to demonstrate accuracy and precision of the technique. Then, in a pilot study on intestinal tissue of mice, we demonstrated the presence of calcium phosphate microparticles, consistent with confocal microscopy observations, and we identified the average molar P:Ca molar ratio as 1.0. Further work will confirm the exact chemical speciation of these particles and will examine the influence of differing calcium containing diets on the formation of these microparticles.

  19. Identification and quantitive analysis of calcium phosphate microparticles in intestinal tissue by nuclear microscopy

    International Nuclear Information System (INIS)

    Microscopic particles (0.5-2 μm diameter), rich in calcium and phosphorus, are found in the lumen of the mid-distal gut of all mammals investigated, including humans, and these may play a role in immuno-surveillance and immune regulation of antigens from food and symbiotic bacteria that are contained in the gut. Whether these particles can cross in to tissue of the intestinal mucosa is unclear. If so, characterising their morphology and chemical composition is an important task in elucidating their function. The analysis of calcium phosphate in biological tissues has been approached in several ways including optical microscopy, scanning electron microscopy and, most recently in this work, with nuclear microscopy. In this paper, we describe the use of microPIXE and microRBS to locate these particles and to determine, accurately, the ratio of phosphorus to calcium using the information on sample thickness obtained from RBS to allow the PIXE ratios to be corrected. A commercial sample of hydroxy apatite was used to demonstrate accuracy and precision of the technique. Then, in a pilot study on intestinal tissue of mice, we demonstrated the presence of calcium phosphate microparticles, consistent with confocal microscopy observations, and we identified the average molar P:Ca molar ratio as 1.0. Further work will confirm the exact chemical speciation of these particles and will examine the influence of differing calcium containing diets on the formation of these microparticles

  20. Study on an Improved Phosphate Cement Binder for the Development of Fiber-Reinforced Inorganic Polymer Composites

    OpenAIRE

    Zhu Ding; Jian-Guo Dai; Sarfraz Muner

    2014-01-01

    Magnesium phosphate cement (MPC) has been proven to be a very good repair material for deteriorated concrete structures. It has excellent adhesion performance, leading to high bonding strength with old concrete substrates. This paper presents an experimental study into the properties of MPC binder as the matrix of carbon fiber sheets to form fiber-reinforced inorganic polymer (FRIP) composites. The physical and mechanical performance of the fresh mixed and the hardened MPC paste, the bond st...

  1. Calcific tendinitis of the shoulder in basic calcium phosphate crystal deposition disease

    International Nuclear Information System (INIS)

    Basic calcium phosphate (BCP) crystal deposition can lead to periarticular collections associated with typical radiographic findings, most frequently observed in the shoulder. Moreover, these deposits may be revealed in other articular sites (i.e.,wrist, hand, foot, elbow, hip, etc.). Initially, the calcium deposits may appear poorly defined (cloudlike); sequently, they may reveal different patterns (linear, triangular or circular areas), changing in size, configuration and site. Adjacent bone may be normal, altough osteoporosis, cystic lesions and reactive sclerosis are reported. The radiographic appearance of calcifications will depend upon the exact location of the deposits in the specific tendon of the rotator cuff, the adjacent bursae and the soft tissues

  2. Influence of portland cement replacement in high calcium fly ash geopolymer paste

    Directory of Open Access Journals (Sweden)

    Tanakorn Phoo-ngernkham

    2014-03-01

    Full Text Available This article presents the influence of ordinary Portland cement (OPC replacement in high calcium fly ash (FA geopolymer paste. FA was used to replace OPC at the rate of 5, 10 and 15% by mass of binder. Sodium silicate (Na2SiO3 and 10 molar sodium hydroxide (NaOH solutions were used as the alkaline solution in the reaction. The Na2SiO3/NaOH ratio of 2.0 and the liquid/binder (L/B ratio of 0.60 were used in all mixtures. The results of increase OPC replacement, the setting time and compressive strain capacity decreased while the compressive strength and modulus of elasticity increased. The compressive strength and modulus of elasticity at 28 days of geopolymer pastes with 15% OPC replacement were 36.7 MPa and 13,300 MPa, respectively.

  3. Indirect pulp therapy in a symptomatic mature molar using calcium enriched mixture cement

    Directory of Open Access Journals (Sweden)

    Hassan Torabzadeh

    2013-01-01

    Full Text Available Dental pulp has the ability of repair/regeneration. Indirect pulp therapy (IPT is recommended for pulp preservation in asymptomatic teeth with extremely deep caries as well as teeth with clinical symptoms of reversible pulpitis. In this case study, we performed IPT with calcium enriched mixture (CEM cement on a symptomatic permanent molar. After clinical/radiographic examinations the tooth was diagnosed with irreversible pulpitis and associated apical periodontitis. IPT involved partial caries removal, the placement of CEM cement pulp cap and overlying adhesive permanent restoration. At the 1 week follow-up, patient′s spontaneous symptoms had resolved. One-year follow-up demonstrated pulp vitality, clinical function, as well as the absence of pain/tenderness to percussion/palpation/cold sensitivity tests; periapical radiograph showed a healing periradicular lesion with newly formed bone, that is normal pulp with normal periodontium. These favorable results indicate that IPT/CEM may be a good treatment option in comparison to endodontic treatment in young patients. IPT of deep-caries lesion is an easier, more practical and valuable treatment plan than complete caries removal.

  4. Investigation on the biomimetic influence of biopolymers on calcium phosphate precipitation-Part 1: Alginate

    International Nuclear Information System (INIS)

    The understanding of how macromocules act in precipitation of inorganic phases is the key knowledge that is needed to establish the foundation to mimic nature and produce materials with high mechanical modulus besides outstanding optical and thermal properties. This study investigated how addition of small amounts of alginate (7-70 ppm), that presents many carboxylic groups, affects phase distribution and morphology of calcium phosphates, obtained through precipitation and further submitted to calcination and sintering. The results lead to the conclusion that alginate action is dynamic, where alginate molecules act as templates to nucleation, and most of the biopolymer remains in solution even when all calcium phosphate has precipitated. However, despite the effect on phase composition being mainly related to the system's kinetics, alginate does present thermodynamic interaction with the precipitates. It is probable that it acts by reducing the free energy of nucleation, as in heterogeneous nucleation processes.

  5. Preparation of novel bioactive nano-calcium phosphate-hydrogel composites

    Energy Technology Data Exchange (ETDEWEB)

    Juhasz, Judith A; Best, Serena M; Bonfield, William, E-mail: jaj33@cam.ac.u [Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ (United Kingdom)

    2010-02-15

    Nano-sized hydroxyapatite (nHA) and carbonate-substituted hydroxyapatite (nCHA) particles were incorporated into a poly-2-hydroxyethylmethacrylate/polycaprolactone (PHEMA/PCL) hydrogel at a filler content of 10 wt%. Fourier transform infrared absorption, transmission electron microscopy, x-ray diffraction and scanning electron microscopy were used to analyse the physical and chemical characteristics of the calcium phosphate fillers and resultant composites. Nano-sized calcium phosphate particles were produced with a needle-like morphology, average length of 50 nm and an aspect ratio of 3. The nanoparticles were uniformly distributed in the polymer matrix. The addition of both HA and CHA in nano-form enhanced the bioactivity and biocompatibility of the PHEMA/PCL matrix. The carbonate-substitution has allowed for improved bioactivity and biocompatibility of the resultant composite, indicating the potential of this material for use in bone tissue engineering.

  6. Influence of surface treatment of carbon fibers on electrochemical crystallization of calcium phosphate

    Institute of Scientific and Technical Information of China (English)

    TAO Ke; HUANG Su-ping; ZHOU Ke-chao

    2005-01-01

    Electrodeposition technique was used to coat calcium phosphate on carbon fiber which can be used to reinforce hydroxyapatite. The differences between fibers treated with and without nitric acid in electrodeposition were evaluated. The X-ray diffractometry results show that CaHPO4·2H2O is obtained as the kind of calcium phosphate coating on carbon fiber. The scanning electron microscopy photographs and deposit kinetic curve indicate that the influences of the functional group attained by nitric acid treatment, the crystal morphology and crystallization of the coating layers on the fiber with and without treatment rate are obviously different. The functional group, especially the acidic group, can act as nucleation centers of electrochemical crystallization.

  7. Characterization of calcium phosphate coating and zinc incorporation on the porous alumina scaffolds

    Directory of Open Access Journals (Sweden)

    Hermes de Souza Costa

    2007-03-01

    Full Text Available Bone ingrowth requires materials with the existence of open and interconnected pores with diameters larger than 150 µm for proper circulation of nutrients. Such materials must possess enough mechanical strength to avoid failure whilst offering a bioactive surface for bone regeneration. We have developed porous ceramic alumina scaffold with compressive strength that achieves 3.3 MPa by replication method by using the network structure of cellular polymer foam. However, the biocompatibility of ceramics based on Al2O3 requires further improvement so that it could have strong bonding to natural bone tissue. To address this problem of the interface between alumina and bone, we have developed a novel calcium phosphate with Zn2+ (CaP-Zn coating onto porous alumina ceramic scaffold by impregnating with calcium phosphate/poly(vinyl alcohol slurry. The tri-dimensional alumina scaffold coated with CaP-Zn was extensively characterized by SEM, EDS and FTIR.

  8. Calcium phosphate nanoparticles as versatile carrier for small and large molecules across cell membranes

    International Nuclear Information System (INIS)

    The successful transport of molecules across the cell membrane is a key point in biology and medicine. In most cases, molecules alone cannot penetrate the cell membrane, therefore an efficient carrier is needed. Calcium phosphate nanoparticles (diameter: 100–250 nm, depending on the functionalization) were loaded with fluorescent oligonucleotides, peptide, proteins, antibodies, polymers or porphyrins and characterized by dynamic light scattering, nanoparticle tracking analysis and scanning electron microscopy. Any excess of molecules was removed by ultracentrifugation, and the dissolved molecules at the same concentration were used as control. The uptake of such fluorescence-labeled nanoparticles into HeLa cells was monitored by fluorescence microscopy and confocal laser scanning microscopy. Calcium phosphate nanoparticles were able to transport all molecules across the cell membrane, whereas the dissolved molecules alone were taken up only to a very small extent or even not at all.

  9. A brief review of calcium phosphate conversion coating on magnesium and its alloys

    Science.gov (United States)

    Zaludin, Mohd Amin Farhan; Jamal, Zul Azhar Zahid; Jamaludin, Shamsul Baharin; Derman, Mohd Nazree

    2016-07-01

    Recent developments have shown that magnesium is a promising candidate to be used as a biomaterial. Owing to its light weight, biocompatibility and compressive strength comparable with natural bones makes magnesium as an excellent choice for biomaterial. However, high reactivity and low corrosion resistance properties have restricted the application of magnesium as biomaterials. At the moment, several strategies have been developed to solve this problem. Surface modification of magnesium is one of the popular solutions to solve the problem. Among many techniques developed in the surface modification, conversion coating method is one of the simple and effective techniques. From various types of conversion coating, calcium phosphate-based conversion coating is the most suitable for biomedical fields. This paper reviews some studies on calcium phosphate coating on Mg and its alloys via chemical conversion method and discusses some factors determining the coating performance.

  10. Preparation of novel bioactive nano-calcium phosphate-hydrogel composites

    International Nuclear Information System (INIS)

    Nano-sized hydroxyapatite (nHA) and carbonate-substituted hydroxyapatite (nCHA) particles were incorporated into a poly-2-hydroxyethylmethacrylate/polycaprolactone (PHEMA/PCL) hydrogel at a filler content of 10 wt%. Fourier transform infrared absorption, transmission electron microscopy, x-ray diffraction and scanning electron microscopy were used to analyse the physical and chemical characteristics of the calcium phosphate fillers and resultant composites. Nano-sized calcium phosphate particles were produced with a needle-like morphology, average length of 50 nm and an aspect ratio of 3. The nanoparticles were uniformly distributed in the polymer matrix. The addition of both HA and CHA in nano-form enhanced the bioactivity and biocompatibility of the PHEMA/PCL matrix. The carbonate-substitution has allowed for improved bioactivity and biocompatibility of the resultant composite, indicating the potential of this material for use in bone tissue engineering.

  11. Properties of MSW fly ash-calcium sulfoaluminate cement matrix and stabilization/solidification on heavy metals.

    Science.gov (United States)

    Qian, G R; Shi, J; Cao, Y L; Xu, Y F; Chui, P C

    2008-03-21

    In this paper, investigations were undertaken to formulate the properties of fly ash-calcium sulfoaluminate (CSA) cement matrix by blending MSW fly ash with CSA cement. The compressive strength, pore structure, hydration phases, and leaching behavior of Zn and Pb doped MSW fly ash-CSA cement matrices were determined by XRD, MIP, DSC, FTIR, EDX, TCLP leaching test and other experiments. The results showed that the addition of MSW fly ash to form fly ash-CSA cement matrix reduced the compressive strengths of matrices and made the pore distribution of matrices coarser, compared to that of pure CSA cement matrix. However, fly ash-CSA cement matrix could effectively immobilize high concentration of heavy metal such as lead and zinc with much lesser leaching of TCLP. Besides ettringite AFt, Friedel phase was a new hydration phase formed in the matrix. The formation of these hydration phases was responsible for huge reservoir of heavy metal stabilization by chemical fixing. Therefore, it could be postulated that MSW fly ash-CSA cement matrix was a potential new constituent of S/S matrix for high concentration of heavy metals such as Zn and Pb ions. PMID:17728061

  12. Manufacturing of calcium phosphate scaffolds by pseudomorphic transformation of gypsum

    Energy Technology Data Exchange (ETDEWEB)

    Araujo Batista, H. de.; Batista Cardoso, M.; Sales Vasconcelos, A.; Vinicius Lia Fook, M.; Rodriguez Barbero, M. A.; Garcia Carrodeguas, R.

    2016-08-01

    Carbonated hydroxyapatite (CHAp) and β-tricalcium phosphate (β-TCP) have been employed for decades as constituents of scaffolds for bone regeneration because they chemically resemble bone mineral. In this study, the feasibility to manufacture CHAp/β-TCP scaffolds by pseudomorphic transformation of casted blocks of gypsum was investigated. The transformation was carried out by immersing the precursor gypsum block in 1 M (NH{sub 4}){sub 2}HPO{sub 4}/1.33 M NH{sub 4}OH solution with liquid/solid ratio of 10 mL/g and autoclaving at 120 degree centigrade and 203 kPa (2 atm) for 3 h at least. Neither shape nor dimensions significantly changed during transformation. The composition of scaffolds treated for 3 h was 70 wt.% CHAp and 30 wt.% β-TCP, and their compressive and diametral compressive strengths were 6.5 ± 0.7 and 5.3 ±0.7 MPa, respectively. By increasing the time of treatment to 6 h, the composition of the scaffold enriched in β-TCP (60 wt.% CHAp and 40 wt.% β-TCP) but its compressive and diametral compressive strengths were not significantly affected (6.7 ± 0.9 and 5.4 ± 0.6 MPa, respectively). On the basis of the results obtained, it was concluded that this route is a good approach to the manufacturing of biphasic (CHAp/β-TCP) scaffolds from previously shaped pieces of gypsum. (Author)

  13. Studies on the mechanisms underlying the transfer of calcium and phosphate from bone to blood

    Energy Technology Data Exchange (ETDEWEB)

    Brommage, Robert J. Jr.

    1978-01-01

    The skeleton is recognized as a crucial organ in the minute-to-minute regulation of the blood levels of calcium and phosphate. The fluxes of calcium and phosphate to and from bone greatly exceed the entry and exit of these ions occurring in the intestine and kidneys. Parathyroid hormone, calcitonin, and 1,25-dihydroxyvitamin D/sub 3/ (1,25-(OH)/sub 2/D/sub 3/ are known to influence the transfer of calcium and phosphate from bone to blood. Three mechanisms have been proposed to explain the hormonal control of the calcium and phosphate effluxes from bone. The concept of a bone membrane maintaining a distinct bone extracellular fluid composition has led to the pump and pH gradient theories. An alternate solubilizer theory proposes that bone cells secrete a substance which increases the solubility of the bone mineral. The bone membrane concept was originally proposed to explain the presence of the apparent anomalously high concentrations of potassium in the bone extracellular fluid. However, the available evidence does not allow an unambiguous decision concerning the presence of a bone membrane. Calvarial lactate production was unaltered by 1,25-(OH)/sub 2/D/sub 3/ treatment and consequently 1,25-(OH)/sub 2/D/sub 3/ does not appear to promote the mobilization of bone mineral through a lactate-mediated pH gradient mechanism. 1,25-(OH)/sub 2/D/sub 3/ did increase the solubility of non-vital bone, clearly demonstrating that the solubilizer mechanism is at least partially responsible for the mobilization of bone mineral and the regulation of blood levels of calcium and phosphate. Vitamin D-deficient female rats fed a 0.2% calcium, 0.4% phosphorous diet and supplemented with daily injections of 0.75 pmole of 1,25-(OH)/sub 2/D/sub 3/ were shown to be capable of bearing young. When the injections of 1,25-(OH)/sub 2/D/sub 3/ were terminated at delivery, the dams and pups showed signs of vitamin D deficiency approximately one week later.

  14. Remineralization of early enamel lesions using casein phosphopeptide amorphous calcium Phosphate: An ex-vivo study

    OpenAIRE

    Ruchi Vashisht; Anil Kumar; Indira, R; Srinivasan, M R; Ramachandran, S.

    2010-01-01

    Objective: This study aimed at qualitatively evaluating the remineralization potential of casein phosphopeptide amorphous calcium phosphate on artificial early enamel lesions in an ex-vivo scenario by observing the treated tooth surface using a scanning electron microscope (SEM). Materials and Methods: This randomized study was conducted on 10 subjects undergoing orthodontic treatment with premolar extraction as part of their treatment. Artificial white lesions were created with the applicati...

  15. Protective potential of casein phosphopeptide amorphous calcium phosphate containing paste on enamel surfaces

    OpenAIRE

    Padmini Somasundaram; Vimala, N; Lalita Gauri Mandke

    2013-01-01

    Background: Dental caries remains the most common dental disease facing mankind. Prevention of initiation and interruption in progression of early lesions are the desirable modes of caries management. There is a scope for agents, which may be used to enhance anti - caries activity. This need has redirected research to develop novel preventive agents that can act as an adjunct to fluoride or independent of it. Casein Phosphopeptide - Amorphous Calcium Phosphate (CPP-ACP) is one such agent that...

  16. Effect of different calcium phosphate scaffold ratios on odontogenic differentiation of human dental pulp cells

    Energy Technology Data Exchange (ETDEWEB)

    AbdulQader, Sarah Talib [School of Dental Sciences, Universiti Sains Malaysia, 16150 Kubang Kerian, Kelantan (Malaysia); Department of Pedodontic and Preventive Dentistry, College of Dentistry, University of Baghdad, Baghdad (Iraq); Kannan, Thirumulu Ponnuraj, E-mail: kannan@usm.my [School of Dental Sciences, Universiti Sains Malaysia, 16150 Kubang Kerian, Kelantan (Malaysia); Human Genome Centre, School of Medical Sciences, Universiti Sains Malaysia, 16150 Kubang Kerian, Kelantan (Malaysia); Rahman, Ismail Ab [School of Dental Sciences, Universiti Sains Malaysia, 16150 Kubang Kerian, Kelantan (Malaysia); Ismail, Hanafi [School of Materials and Minerals Resource Engineering, Universiti Sains Malaysia, 14300 Penang (Malaysia); Mahmood, Zuliani [School of Dental Sciences, Universiti Sains Malaysia, 16150 Kubang Kerian, Kelantan (Malaysia)

    2015-04-01

    Calcium phosphate (CaP) scaffolds have been widely and successfully used with osteoblast cells for bone tissue regeneration. However, it is necessary to investigate the effects of these scaffolds on odontoblast cells' proliferation and differentiation for dentin tissue regeneration. In this study, three different hydroxyapatite (HA) to beta tricalcium phosphate (β-TCP) ratios of biphasic calcium phosphate (BCP) scaffolds, BCP20, BCP50, and BCP80, with a mean pore size of 300 μm and 65% porosity were prepared from phosphoric acid (H{sub 2}PO{sub 4}) and calcium carbonate (CaCO{sub 3}) sintered at 1000 °C for 2 h. The extracts of these scaffolds were assessed with regard to cell viability and differentiation of odontoblasts. The high alkalinity, more calcium, and phosphate ions released that were exhibited by BCP20 decreased the viability of human dental pulp cells (HDPCs) as compared to BCP50 and BCP80. However, the cells cultured with BCP20 extract expressed high alkaline phosphatase activity and high expression level of bone sialoprotein (BSP), dental matrix protein-1 (DMP-1), and dentin sialophosphoprotein (DSPP) genes as compared to that cultured with BCP50 and BCP80 extracts. The results highlighted the effect of different scaffold ratios on the cell microenvironment and demonstrated that BCP20 scaffold can support HDPC differentiation for dentin tissue regeneration. - Highlights: • BCPs of different HA/β-TCP ratios influence cell microenvironment. • BCP20 decreases cell viability of HDPCs as compared to BCP50 and BCP80. • HDPCs cultured with BCP20 express highest ALP activity. • HDPCs cultured with BCP20 up-regulate BSP, DMP-1 and DSPP gene expressions. • BCP20 can support HDPC differentiation for dentin tissue regeneration.

  17. Characterisation of calcium phosphate layers grown on polycaprolactone for tissue engineering purposes

    OpenAIRE

    Lebourg, M.; Antón, J. Suay; Ribelles, J.L. Gomez

    2010-01-01

    Abstract Composites fabricated by biomimetic mineral precipitation on polymeric substrates are of interest for tissue engineering. As biological properties of such mineral layers vary with slight changes in composition, a good physical characterization is necessary in order to study their biological activity. In this work polycaprolactone sheets were subjected to air plasma treatment followed by nucleation of calcium phosphate seeds to activate the growth of an apatite-like coating...

  18. Evaluation of implant calcium-phosphate materials depending on their mineral content

    Directory of Open Access Journals (Sweden)

    I. A. Talashova

    2016-03-01

    Full Text Available Biocompatibility of original implant calcium-phosphate materials was evaluated in the experiment on animals. The methods of radiological electron-probe microanalysis (REMA and light and scan electron microscopy (SEM were used. Studied materials had the properties of biodegradation, osteoinduction and osteoconduction at different extent. The materials with the composite maximally close to the the bone tissue had the greatest grade of biocompatibility.

  19. Optimizing and Evaluating the Biocompatibility of Fiber Composites with Calcium Phosphate Additives

    Czech Academy of Sciences Publication Activity Database

    Suchý, Tomáš; Balík, Karel; Sucharda, Zbyněk; Sochor, M.; Lapčíková, Monika; Sedláček, R.

    2011-01-01

    Roč. 161, 19/20 (2011), s. 493-502. ISSN 0043-5341 R&D Projects: GA ČR(CZ) GAP108/10/1457; GA ČR(CZ) GA106/06/1576 Institutional research plan: CEZ:AV0Z30460519; CEZ:AV0Z40500505 Keywords : biocomposites * calcium phosphate * polyamide fibers Subject RIV: JI - Composite Materials http://www.springerlink.com/content/047q753g04h4l836/

  20. Calcium Phosphate Nanocomposite Particles for In Vitro Imaging and Encapsulated Chemotherapeutic Drug Delivery to Cancer Cells

    OpenAIRE

    Kester, Mark; Heakal, Y.; Sharma, A.; Robertson, Gavin P.; Morgan, Thomas T.; İ Altinoğlu, Erhan; Tabaković, Amra; Parette, Mylisa R.; Rouse, Sarah; Ruiz-Velasco, Victor; Adair, James H.

    2008-01-01

    Paradigm-shifting modalities to more efficiently deliver drugs to cancerous lesions require the following attributes: nanoscale-size, targetability and stability under physiological conditions. Often, these nanoscale drug delivery vehicles are limited due to agglomeration, poor solubility or cytotoxicity. Thus, we have designed a methodology to encapsulate hydrophobic antineoplastic chemotherapeutics within a 20-30 nm diameter, pH-responsive, non-agglomerating, non-toxic calcium phosphate nan...

  1. Ionic liquid-assisted formation of cellulose/calcium phosphate hybrid materials

    OpenAIRE

    Ahmed Salama; Mike Neumann; Christina Günter; Andreas Taubert

    2014-01-01

    Cellulose/calcium phosphate hybrid materials were synthesized via an ionic liquid-assisted route. Scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, infrared spectroscopy, and thermogravimetric analysis/differential thermal analysis show that, depending on the reaction conditions, cellulose/hydroxyapatite, cellulose/chlorapatite, or cellulose/monetite composites form. Preliminary studies with MC3T3-E1 pre-osteoblasts show t...

  2. Ability of Pit and Fissure Sealant-containing Amorphous Calcium Phosphate to inhibit Enamel Demineralization

    OpenAIRE

    Zawaideh, Feda I; Owais, Arwa I; Kawaja, Wasan

    2016-01-01

    ABSTRACT Aim: To evaluate the effect of amorphous calcium phosphate (ACP)-containing pit and fissure sealant on inhibition of enamel demineralization in vitro. Materials and methods: Enamel specimens (n = 75) were prepared using freshly extracted noncarious human third molars. Box-shaped cavities (8 × 2 × 2 mm) on the buccal or lingual surfaces were prepared and restored with resin-based sealant (Concise™), ACP-containing sealant (Aegis®) or fluoride-containing sealant (Conseal-F™). The sampl...

  3. Calcium phosphate preservation of faecal bacterial negative moulds in hyaena coprolites

    OpenAIRE

    Pesquero, María Dolores; Souza Egipsy, Virginia; Alcalá, Luis; Ascaso, Carmen; Fernández Jalvo, Yolanda

    2014-01-01

    The vertebrate fossil locality of La Roma 2, Spain (Upper Miocene, Late Vallesian, MN10) is characterised by a high abundance of mammalian coprolites, which provide direct clues to the diets and habitats of the organisms that produced them. X-ray diffraction analysis showed a sample of hyaena (cf. Lycyaena chaeretis) coprolites to be mostly composed of calcium phosphate. Ultrastructural SEM and TEM studies revealed three successive phases of preservation, including an initial phase of mineral...

  4. Trace element doping in calcium phosphate ceramics to Understand osteogenesis and angiogenesis

    OpenAIRE

    Bose, Susmita; Fielding, Gary; Tarafder, Solaiman; Bandyopadhyay, Amit

    2013-01-01

    The general trends in synthetic bone grafting materials are shifting towards approaches that can illicit osteoinductive properties. Pharmacologics and biologics have been used in combination with calcium phosphate (CaP) ceramics, however, recently have become the target of scrutiny over the safety. The importance of trace elements in natural bone health is well documented. Ions, e.g. lithium, zinc, magnesium, manganese, silicon, strontium etc. have shown to increase osteogenesis and neovascul...

  5. Electrodeposition on nanofibrous polymer scaffolds: Rapid mineralization, tunable calcium phosphate composition and topography

    OpenAIRE

    He, Chuanglong; Xiao, Guiyong; Jin, Xiaobing; Sun, Chenghui; Ma, Peter X.

    2010-01-01

    We developed a straightforward, fast, and versatile technique to fabricate mineralized nanofibrous polymer scaffolds for bone regeneration in this work. Nanofibrous poly(l-lactic acid) scaffolds were fabricated using both electrospinning and phase separation techniques. An electrodeposition process was designed to deposit calcium phosphate on the nanofibrous scaffolds. Such scaffolds contain a high quality mineral coating on the fiber surface with tunable surface topography and chemical compo...

  6. Nano-sized calcium phosphate (CaP) carriers for non-viral gene deilvery

    International Nuclear Information System (INIS)

    Highlights: ► Nanostructured calcium phosphates (NanoCaPs): comprehensive review. ► Non viral gene delivery mechanisms: detailed mechanisms are outlined. ► Barriers to non-viral gene delivery: detailed barriers are discussed. - Abstract: Gene therapy has garnered much interest due to the potential for curing multiple inherited and/or increases in the acquired diseases. As a result, there has been intense activity from multiple research groups for developing effective delivery methods and carriers, which is a critical step in advancing gene delivery technologies. In order for the carriers to effectively deliver the genetic payloads, multiple extracellular and intracellular barriers need to be overcome. Although overcoming these challenges to improve the effectiveness is critical, the development of safe gene delivery agents is even more vital to assure its use in clinical applications. The development of safe and effective strategies has therefore been a major challenge impeding gene therapy progress. In this regard, calcium phosphate (CaP) based nano-particles has been considered as one of the candidate non-viral gene delivery vehicles, but has been plagued by inconsistent and low transfection efficiencies limiting its progress. There has been major research effort to improve the consistency and effectiveness of CaP based vectors. Currently, it is therefore thought that by controlling the various synthesis factors such as Ca/P ratio, mode of mixing, and type of calcium phosphate phase, such variability and inefficiency could be modulated. This review attempts to provide a comprehensive analysis of the current research activity in the development of CaP based ceramic and polymer-ceramic hybrid systems for non-viral gene delivery. Preliminary transfection results of hydroxyapatite (HA or NanoCaPs), amorphous calcium phosphate (ACP) and brushite phases are also compared to assess the effect of various CaP phases, and correspondingly, changes in the dissolution

  7. Effect of different calcium phosphate scaffold ratios on odontogenic differentiation of human dental pulp cells

    International Nuclear Information System (INIS)

    Calcium phosphate (CaP) scaffolds have been widely and successfully used with osteoblast cells for bone tissue regeneration. However, it is necessary to investigate the effects of these scaffolds on odontoblast cells' proliferation and differentiation for dentin tissue regeneration. In this study, three different hydroxyapatite (HA) to beta tricalcium phosphate (β-TCP) ratios of biphasic calcium phosphate (BCP) scaffolds, BCP20, BCP50, and BCP80, with a mean pore size of 300 μm and 65% porosity were prepared from phosphoric acid (H2PO4) and calcium carbonate (CaCO3) sintered at 1000 °C for 2 h. The extracts of these scaffolds were assessed with regard to cell viability and differentiation of odontoblasts. The high alkalinity, more calcium, and phosphate ions released that were exhibited by BCP20 decreased the viability of human dental pulp cells (HDPCs) as compared to BCP50 and BCP80. However, the cells cultured with BCP20 extract expressed high alkaline phosphatase activity and high expression level of bone sialoprotein (BSP), dental matrix protein-1 (DMP-1), and dentin sialophosphoprotein (DSPP) genes as compared to that cultured with BCP50 and BCP80 extracts. The results highlighted the effect of different scaffold ratios on the cell microenvironment and demonstrated that BCP20 scaffold can support HDPC differentiation for dentin tissue regeneration. - Highlights: • BCPs of different HA/β-TCP ratios influence cell microenvironment. • BCP20 decreases cell viability of HDPCs as compared to BCP50 and BCP80. • HDPCs cultured with BCP20 express highest ALP activity. • HDPCs cultured with BCP20 up-regulate BSP, DMP-1 and DSPP gene expressions. • BCP20 can support HDPC differentiation for dentin tissue regeneration

  8. Current and Future Theranostic Applications of the Lipid-Calcium-Phosphate Nanoparticle Platform

    OpenAIRE

    Satterlee, Andrew B.; Huang, Leaf

    2016-01-01

    Over the last four years, the Lipid-Calcium-Phosphate (LCP) nanoparticle platform has shown success in a wide range of treatment strategies, recently including theranostics. The high specific drug loading of radiometals into LCP, coupled with its ability to efficiently encapsulate many types of cytotoxic agents, allows a broad range of theranostic applications, many of which are yet unexplored. In addition to providing an overview of current medical imaging modalities, this review highlights ...

  9. Effect of Microstructural Evolution on Wettability of Laser Coated Calcium Phosphate on Titanium Alloy

    Energy Technology Data Exchange (ETDEWEB)

    Kurella, Anil K [ORNL; Hu, Michael Z. [ORNL; Dahotre, Narendra B [ORNL

    2008-01-01

    Surface engineering of synthetic implant materials provides an exciting opportunity to mimic natural biomaterials. Surface that are bioactive and textured at multi scale have the potential for easier osseointegration. Ti alloy surfaces known for their biocompatibility are coated with bioactive Calcium Phosphate using a laser source at multiple processing speeds. The resulting surface has multiscale morphology and multi-phase chemical nature. Faster processing speeds showed improved wettability to water along with higher degree of crystallinity in the phases present.

  10. Effects of Calcium Phosphate Nanocrystals on Osseointegration of Titanium Implant in Irradiated Bone

    OpenAIRE

    2015-01-01

    Radiotherapy may compromise the integration of implant and cause implant loss. Implant surface modifications have the possibility of promoting cell attachment, cell growth, and bone formation which ultimately enhance the osseointegration process. The present study aimed to investigate the effects of calcium phosphate nanocrystals on implant osseointegration in irradiated bone. Sixteen rabbits were randomly assigned into control and nano-CaP groups, receiving implants with dual acid-etched sur...

  11. The effect of calcium phosphate nanoparticles on hormone production and apoptosis in human granulosa cells

    Directory of Open Access Journals (Sweden)

    Gao Li

    2010-04-01

    Full Text Available Abstract Objectives Although many nanomaterials are being used in academia, industry and daily life, there is little understanding about the effects of nanoparticles on the reproductive health of vertebral animals, including human beings. An experimental study was therefore performed here to explore the effect of calcium phosphate nanoparticles on both steroid hormone production and apoptosis in human ovarian granulosa cells. Methods Calcium phosphate nanoparticles uptaking was evaluated by transmission electron microscopy (TEM. The cell cycle was assessed with propidium iodide-stained cells (distribution of cells in G0/G1, S, and G2/M phases by flow cytometry. The pattern of cell death (necrosis and apoptosis was analyzed by flow cytometry with annexin V-FITC/PI staining. The expression of mRNAs encoding P450scc, P450arom and StAR were determined by RT-PCR. Progesterone and estradiol levels were measured by radioimmunoassay. Results TEM results confirmed that calcium phosphate nanoparticles could enter into granulosa cells, and distributed in the membranate compartments, including lysosome and mitochondria and intracellular vesicles. The increased percentage of cells in S phase when cultured with nanoparticles indicated that there was an arrest at the checkpoint from phase S-to-G2/M (from 6.28 +/- 1.55% to 11.18 +/- 1.73%, p Conclusion Calcium phosphate nanoparticles interfered with cell cycle of cultured human ovarian granulosa cells thus increasing cell apoptosis. This pilot study suggested that effects of nanoparticles on ovarian function should be extensively investigated.

  12. Next-generation resorbable polymer scaffolds with surface-precipitated calcium phosphate coatings

    OpenAIRE

    Kim, Jinku; Magno, Maria Hanshella R.; Ortiz, Ophir; McBride, Sean; Darr, Aniq; Kohn, Joachim; Hollinger, Jeffrey O.

    2015-01-01

    Next-generation synthetic bone graft therapies will most likely be composed of resorbable polymers in combination with bioactive components. In this article, we continue our exploration of E1001(1k), a tyrosine-derived polycarbonate, as an orthopedic implant material. Specifically, we use E1001(1k), which is degradable, nontoxic, and osteoconductive, to fabricate porous bone regeneration scaffolds that were enhanced by two different types of calcium phosphate (CP) coatings: in one case, pure ...

  13. Mechanical and acid neutralizing properties and bacteria inhibition of amorphous calcium phosphate dental nanocomposite

    OpenAIRE

    Moreau, Jennifer L.; Sun, Limin; Chow, Laurence C.; Xu, Hockin H. K.

    2011-01-01

    Dental composites do not hinder bacteria colonization and plaque formation. Caries at the restoration margins is a frequent reason for replacement of existing restorations, which accounts for 50 to 70% of all restorations. The objectives of this study were to examine the filler level effect on nanocomposite containing nanoparticles of amorphous calcium phosphate (NACP) and investigate the load-bearing and acid-neutralizing properties and bacteria inhibition. NACP with 116-nm particle size wer...

  14. EVALUATION OF ACTIVITY OF POLYPHENOLOXIDASE ENZYME AND INTERCALATION OF THE CALCIUM PHOSPHATE WITH TETRABUTYLAMMONIUM HYDROXIDE

    OpenAIRE

    CESÁRIO, Moisés Rômolos; MOURA, Danyelle Medeiros de Araújo; MACEDO, Daniel Araújo de; LIMA, Cícero Bosco Alves de

    2011-01-01

    Biosensors are digital devices composed of semiconductors connected to a biological component, usually an immobilized enzyme, which are used to measure the concentration of a specific substrate. This study aimed to obtain and purify the polyphenol oxidase enzyme (PPO) obtained from the crude extract of yam (Alocasia macrorhiza), and study the exfoliation reaction of calcium phosphate (CaP) with tetrabutylammonium hydroxide (TBA+OH-). The thermogravimetric study indicated the formation of t...

  15. Formation of calcium phosphates by vapour diffusion in highly concentrated ionic micro-droplets

    Energy Technology Data Exchange (ETDEWEB)

    Iafisco, M. [Alma Mater Studiorum Universita di Bologna, Dipartimento di Chimica ' ' G. Ciamician' ' , Via Selmi 2, 40126 Bologna (Italy); Universita del Piemonte Orientale, Dipartimento di Scienze Mediche, Via Solaroli 4, 28100 Novara (Italy); Delgado-Lopez, J.M.; Gomez-Morales, J.; Hernandez-Hernandez, M.A.; Rodriguez-Ruiz, I. [Laboratorio de Estudios Cristalograficos, IACT CSIC-UGR, Edificio Lopez Neyra, Avenida del Conocimiento, s/n 18100 Armilla (Spain); Roveri, N. [Alma Mater Studiorum Universita di Bologna, Dipartimento di Chimica ' ' G. Ciamician' ' , Via Selmi 2, 40126 Bologna (Italy)

    2011-08-15

    In this work we have used the sitting drop vapour diffusion technique, employing the ''crystallization mushroom '' to analyze the evolution of calcium phosphate crystallization in micro-droplets containing high initial concentrations of Ca{sup 2+} and HPO{sub 4}{sup 2-}. The decomposition of NH{sub 4}HCO{sub 3} solution produces vapours of NH{sub 3} and CO{sub 2} which diffuse through the droplets containing an aqueous solution of Ca(CH{sub 3}COO){sub 2} and (NH{sub 4}){sub 2}HPO{sub 4}. The result is the increase of pH by means of the diffusion of NH{sub 3} gas and the doping of the calcium phosphate with CO{sub 3}{sup 2-} ions by means of the diffusion of CO{sub 2} gas. The pH of the crystallization process is monitored and the precipitates at different times are characterized by XRD, FTIR, TGA, SEM and TEM techniques. The slow increase of pH and the high concentration of Ca{sup 2+} and HPO{sub 4}{sup 2-} in the droplets induce the crystallization of three calcium phosphate phases: dicalcium phosphate dihydrate (DCPD, brushite), octacalcium phosphate (OCP) and carbonate-hydroxyapatite (HA). The amount of HA nanocrystals with needle-like morphology and dimensions of about 100 nm, closely resembling the inorganic phase of bones, gradually increases, with the precipitation time up to 7 days, whereas the amount of DCPD, growing along the b axis, increases up to 3 days. Then, DCDP crystals start to hydrolyze yielding OCP nanoribbons and HA nanocrystals. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  16. Cell response of calcium phosphate based ceramics, a bone substitute material

    Directory of Open Access Journals (Sweden)

    Juliana Marchi

    2013-01-01

    Full Text Available The aim of this study was to characterize calcium phosphate ceramics with different Ca/P ratios and evaluate cell response of these materials for use as a bone substitute. Bioceramics consisting of mixtures of hydroxyapatite (HAp and β-tricalcium phosphate (β-TCP powders in different proportions were pressed and sintered. The physical and chemical properties of these bioceramics were then characterized. Characterization of the biological properties of these materials was based on analysis of cell response using cultured fibroblasts. The number of cells attached to the samples was counted from SEM images of samples exposed to cell culture solution for different periods. These data were compared by analysis of variance (ANOVA complemented by the Tukey's test. The TCP sample had higher surface roughness and lower density. The adherence and growth of FMM1 cells on samples from all groups was studied. Even though the different calcium based ceramics exhibited properties which made them suitable as bone substitutes, those with higher levels of β-TCP revealed improved cell growth on their surfaces. These observations indicated two-phase calcium phosphate based materials with a β-TCP surface layer to be a promising bone substitute.

  17. The formation of calcium phosphate coatings by pulse laser deposition on the surface of polymeric ferroelectric

    International Nuclear Information System (INIS)

    Graphical abstract: - Highlights: • Calcium phosphate coatings were obtained on ferroelectric polymer materials surface by using PLD method. • Obtained coatings have well-developed surface. • Depending on sputtering target composition it is possible to obtain crystalline or amorphous coating. • Formation of coating does not change the crystal structure of the ferroelectric polymer material. - Abstract: This work analyses the properties of calcium phosphate coatings obtained by pulsed laser deposition on the surface of the ferroelectric polymer material. Atomic force and scanning electron microscopy studies demonstrate that, regardless of the type of sputtering target, the calcium phosphate coatings have a multiscale rough surface that is potentially capable of promoting the attachment and proliferation of osteoblasts. This developed surface of the coatings is due to its formation mainly from a liquid phase. The chemical and crystalline composition of the coatings depends on the type of sputtering target used. It was shown that, regardless of the type of sputtering target, the crystalline structure of the ferroelectric polymer material does not change. Cell viability and adhesion studies of mesenchymal stromal cells on the coatings were conducted using flow cytometry and fluorescent microscopy. These studies indicated that the produced coatings are non-toxic

  18. Designing calcium phosphate-based bifunctional nanocapsules with bone-targeting properties

    Energy Technology Data Exchange (ETDEWEB)

    Khung, Yit-Lung; Bastari, Kelsen; Cho, Xing Ling; Yee, Wu Aik; Loo, Say Chye Joachim, E-mail: joachimloo@ntu.edu.sg [Nanyang Technological University, School of Materials Science and Engineering (Singapore)

    2012-06-15

    Using sodium dodecyl sulphate micelles as template, hollow-cored calcium phosphate nanocapsules were produced. The surfaces of the nanocapsule were subsequently silanised by a polyethylene glycol (PEG)-based silane with an N-hydroxysuccinimide ester end groups which permits for further attachment with bisphosphonates (BP). Characterisations of these nanocapsules were investigated using Field Emission Scanning Electron Microscopy (FESEM), Transmission Electron Microscopy, Fourier Transform Infra-Red Spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy and Dynamic Light Scattering. To further validate the bone-targeting potential, dentine discs were incubated with these functionalised nanocapsules. FESEM analysis showed that these surface-modified nanocapsules would bind strongly to dentine surfaces compared to non-functionalised nanocapsules. We envisage that respective components would give this construct a bifunctional attribute, whereby (1) the shell of the calcium phosphate nanocapsule would serve as biocompatible coating aiding in gradual osteoconduction, while (2) surface BP moieties, acting as targeting ligands, would provide the bone-targeting potential of these calcium phosphate nanocapsules.

  19. Preparation of calcium phosphate coating on pure titanium substrate by electrodeposition method

    Institute of Scientific and Technical Information of China (English)

    赵中伟; 张刚; 李洪桂

    2004-01-01

    The influences of pH value, electrolyte temperature and loading time on depositing calcium phosphate coating on pure titanium substrate by electrodeposition process were investigated. The process was carried out with an electrochemical work-station supplying a direct current power at potential of -0.8V (vs SCE). The electrolyte consists of 7 mmol·L-1 CaCl2·2H2O, 3 mmol·L-1 Ca(H2PO4)2·H2O and 2.5% H2O2. NaOH and HCl solutions were used to adjust pH value. The deposited samples were characterized by X-ray diffraction and scanning electron microscope. The comparison of the deposits obtained at lower and higher pH values demonstrates that the crystallization process at the interface is favoured by high pH value. With temperature increasing, the deposited hydroxyapatite is occasionally of plate-like shape, and the width and the length of the deposited calcium phosphates at 65 ℃ are larger than those at 55 ℃. Therefore, it is confirmed that the morphology and microstructure of electrochemically deposited calcium phosphates can be regulated. Additionally, the coating formed in electrolyte with H2O2 additive is homogeneous and the evolution of H2 bubble can be eliminated.

  20. Europium-doped amorphous calcium phosphate porous nanospheres: preparation and application as luminescent drug carriers.

    Science.gov (United States)

    Chen, Feng; Zhu, Ying-Jie; Zhang, Kui-Hua; Wu, Jin; Wang, Ke-Wei; Tang, Qi-Li; Mo, Xiu-Mei

    2011-01-01

    Calcium phosphate is the most important inorganic constituent of biological tissues, and synthetic calcium phosphate has been widely used as biomaterials. In this study, a facile method has been developed for the fabrication of amorphous calcium phosphate (ACP)/polylactide-block-monomethoxy(polyethyleneglycol) hybrid nanoparticles and ACP porous nanospheres. Europium-doping is performed to enable photoluminescence (PL) function of ACP porous nanospheres. A high specific surface area of the europium-doped ACP (Eu3+:ACP) porous nanospheres is achieved (126.7 m2/g). PL properties of Eu3+:ACP porous nanospheres are investigated, and the most intense peak at 612 nm is observed at 5 mol% Eu3+ doping. In vitro cytotoxicity experiments indicate that the as-prepared Eu3+:ACP porous nanospheres are biocompatible. In vitro drug release experiments indicate that the ibuprofen-loaded Eu3+:ACP porous nanospheres show a slow and sustained drug release in simulated body fluid. We have found that the cumulative amount of released drug has a linear relationship with the natural logarithm of release time (ln(t)). The Eu3+:ACP porous nanospheres are bioactive, and can transform to hydroxyapatite during drug release. The PL properties of drug-loaded nanocarriers before and after drug release are also investigated. PMID:21711603

  1. The formation of calcium phosphate coatings by pulse laser deposition on the surface of polymeric ferroelectric

    Energy Technology Data Exchange (ETDEWEB)

    Bolbasov, E.N. [Tomsk Polytechnic University, 30 Lenin Avenue, Tomsk 634050 (Russian Federation); Lapin, I.N.; Svetlichnyi, V.A. [Tomsk State University, 36 Lenin Avenue, Tomsk 634050 (Russian Federation); Lenivtseva, Y.D. [Tomsk Polytechnic University, 30 Lenin Avenue, Tomsk 634050 (Russian Federation); Malashicheva, A. [Federal Almazov Medical Research Centre, 2 Akkuratova St., St. Petersburg 197341 (Russian Federation); St. Petersburg State University, 7/9 Universitetskaya nab., St. Petersburg 199034 (Russian Federation); ITMO University, Institute of translational Medicine, St. Petersburg (Russian Federation); Malashichev, Y. [St. Petersburg State University, 7/9 Universitetskaya nab., St. Petersburg 199034 (Russian Federation); Golovkin, A.S. [Federal Almazov Medical Research Centre, 2 Akkuratova St., St. Petersburg 197341 (Russian Federation); Anissimov, Y.G. [Griffith University, School of Natural Sciences, Engineering Dr., Southport, QLD 4222 (Australia); Tverdokhlebov, S.I., E-mail: tverd@tpu.ru [Tomsk Polytechnic University, 30 Lenin Avenue, Tomsk 634050 (Russian Federation)

    2015-09-15

    Graphical abstract: - Highlights: • Calcium phosphate coatings were obtained on ferroelectric polymer materials surface by using PLD method. • Obtained coatings have well-developed surface. • Depending on sputtering target composition it is possible to obtain crystalline or amorphous coating. • Formation of coating does not change the crystal structure of the ferroelectric polymer material. - Abstract: This work analyses the properties of calcium phosphate coatings obtained by pulsed laser deposition on the surface of the ferroelectric polymer material. Atomic force and scanning electron microscopy studies demonstrate that, regardless of the type of sputtering target, the calcium phosphate coatings have a multiscale rough surface that is potentially capable of promoting the attachment and proliferation of osteoblasts. This developed surface of the coatings is due to its formation mainly from a liquid phase. The chemical and crystalline composition of the coatings depends on the type of sputtering target used. It was shown that, regardless of the type of sputtering target, the crystalline structure of the ferroelectric polymer material does not change. Cell viability and adhesion studies of mesenchymal stromal cells on the coatings were conducted using flow cytometry and fluorescent microscopy. These studies indicated that the produced coatings are non-toxic.

  2. Development of a Calcium Phosphate Nanocomposite for Fast Fluorogenic Detection of Bacteria

    Directory of Open Access Journals (Sweden)

    Claudio R. Martínez

    2014-09-01

    Full Text Available Current procedures for the detection and identification of bacterial infections are laborious, time-consuming, and require a high workload and well-equipped laboratories. Therefore the work presented herein developed a simple, fast, and low cost method for bacterial detection based on hydroxyapatite nanoparticles with a nutritive mixture and the fluorogenic substrate. Calcium phosphate ceramic nanoparticles were characterized and integrated with a nutritive mixture for the early detection of bacteria by visual as well as fluorescence spectroscopy techniques. The composite was obtained by combining calcium phosphate nanoparticles (Ca:P ratio, 1.33:1 with a nutritive mixture of protein hydrolysates and carbon sources, which promote fast bacterial multiplication, and the fluorogenic substrate 4-methylumbellipheryl-β-d-glucuronide (MUG. The composite had an average particle size of 173.2 nm and did not show antibacterial activity against Gram-negative or Gram-positive bacteria. After an Escherichia coli suspension was in contact with the composite for 60–90 min, fluorescence detected under UV light or by fluorescence spectrophotometer indicated the presence of bacteria. Intense fluorescence was observed after incubation for a maximum of 90 min. Thus, this calcium phosphate nanocomposite system may be useful as a model for the development of other nanoparticle composites for detection of early bacterial adhesion.

  3. Synthesis and characterization of nanocomposite powders of calcium phosphate/silica-gel

    International Nuclear Information System (INIS)

    In the recent years ceramics of calcium phosphate are pointed out as an outstanding material in substitution and regeneration in defects from osseous tissue, in reason of their similar mineralogical characteristics of apatite of bone structure. However, the challenge with phosphate calcium ceramics find out about the mechanical properties and the development of biomaterials similar of the bone structure, what sometimes is not so easy, about fragile materials. The aim of this work focused in synthesis and characterization nanocomposites powders of calcium phosphate/silica-gel with percentages 1, 2, 3 e 5% of nanometric silica. The method synthesis used for the compositions elaboration was dissolution-precipitation. The presented results are related with the optimization to method elaboration of nanostructured powders, the mineralogical characterization with X-ray diffraction, thermal behavior with thermal differential analysis, differential scanning calorimetry here is ADT and dilatometer. The scanning electronic microscopy was used to help of morphological characterization the nanostructured powders and the surfaces from body test recovered from the mechanical test. (author)

  4. Europium-doped amorphous calcium phosphate porous nanospheres: preparation and application as luminescent drug carriers

    Directory of Open Access Journals (Sweden)

    Zhang Kui-Hua

    2011-01-01

    Full Text Available Abstract Calcium phosphate is the most important inorganic constituent of biological tissues, and synthetic calcium phosphate has been widely used as biomaterials. In this study, a facile method has been developed for the fabrication of amorphous calcium phosphate (ACP/polylactide-block-monomethoxy(polyethyleneglycol hybrid nanoparticles and ACP porous nanospheres. Europium-doping is performed to enable photoluminescence (PL function of ACP porous nanospheres. A high specific surface area of the europium-doped ACP (Eu3+:ACP porous nanospheres is achieved (126.7 m2/g. PL properties of Eu3+:ACP porous nanospheres are investigated, and the most intense peak at 612 nm is observed at 5 mol% Eu3+ doping. In vitro cytotoxicity experiments indicate that the as-prepared Eu3+:ACP porous nanospheres are biocompatible. In vitro drug release experiments indicate that the ibuprofen-loaded Eu3+:ACP porous nanospheres show a slow and sustained drug release in simulated body fluid. We have found that the cumulative amount of released drug has a linear relationship with the natural logarithm of release time (ln(t. The Eu3+:ACP porous nanospheres are bioactive, and can transform to hydroxyapatite during drug release. The PL properties of drug-loaded nanocarriers before and after drug release are also investigated.

  5. Effect of citric acid and the hemihydrate amount on the properties of a calcium sulphoaluminate cement

    Directory of Open Access Journals (Sweden)

    Velazco, G.

    2014-12-01

    Full Text Available The influence of citric acid on the hydration and strength development of a calcium sulphoaluminate cement was investigated. Cement pastes were prepared by mixing calcium sulphoaluminate (C4A3Ŝ with 15, 20 and 25wt% of hemihydrate (CŜH0.5. Citric acid was added as a retarder at 0 and 0.5wt%. The samples were cured at 20 °C for periods of time from 1 to 28 days to evaluate their compressive strength and to characterize the hydration products by scanning electron microscopy and X-ray diffraction. Calorimetric curves showed that the retarding agent considerably decreases the heat release rate and the quantity of total heat released. The main product after the curing was ettringite (C6AŜ3H32. The morphology of this phase consisted of long and thin needles growing radially on the cement grains. Samples with 15wt% of hemihydrate and 0.5wt% of citric acid developed the highest compressive strength (70 MPa at 28 days of curing.Se investigó el efecto del ácido cítrico sobre la hidratación y propiedades mecánicas de un cemento de sulfoaluminato de calcio. El C4A3Ŝ se mezcló con 15, 20 y 25% e.p. de hemihidrato (CŜH0.5. Se agregó ácido cítrico como retardante en 0 y 0.5% e.p. Las muestras fueron curadas a 20 °C por periodos de 1 a 28 días para realizar mediciones de resistencia a la compresión y caracterizar los productos de hidratación mediante microscopía electrónica de barrido y difracción de rayos X. Las curvas de calorimetría mostraron ue el ácido cítrico disminuye la velocidad de liberación de calor y la cantidad de calor liberado durante la hidratación. La resistencia a la compresión alcanzó un máximo de 70 MPa en muestras con 15% e.p. de hemihidrato y 0,5% e.p de ácido cítrico. Los resultados muestran a la etringita (C6AŜ3H32 como principal producto de hidratación. Se observa a esta fase con morfología acicular creciendo sobre las partículas de cemento.

  6. Mineralization of Annexin-5-containing Lipid-Calcium-Phosphate Complexes: MODULATION BY VARYING LIPID COMPOSITION AND INCUBATION WITH CARTILAGE COLLAGENS*

    OpenAIRE

    Genge, Brian R.; Wu, Licia N. Y.; Wuthier, Roy E.

    2008-01-01

    Matrix vesicles (MVs) in the growth plate bind to cartilage collagens and initiate mineralization of the extracellular matrix. Native MVs have been shown to contain a nucleational core responsible for mineral formation that is comprised of Mg2+-containing amorphous calcium phosphate and lipid-calcium-phosphate complexes (CPLXs) and the lipid-dependent Ca2+-binding proteins, especially annexin-5 (Anx-5), which greatly enhances mineral formation. Incorporation of non-Ca2...

  7. Biomimetic synthesis of modified calcium phosphate fine powders and their in vitro studies

    Energy Technology Data Exchange (ETDEWEB)

    Gergulova, R., E-mail: rumigg@yahoo.com; Tepavitcharova, S., E-mail: rumigg@yahoo.com; Rabadjieva, D., E-mail: rumigg@yahoo.com; Sezanova, K., E-mail: rumigg@yahoo.com; Ilieva, R., E-mail: rumigg@yahoo.com [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, Acad. G. Bonchev Str., Bl. 11, 1113 Sofia (Bulgaria); Alexandrova, R.; Andonova-Lilova, B. [Institute of Experimental Morphology, Pathology and Anthropology with Museum, BAS, Acad. G. Bonchev Str., Bl. 25, Sofia (Bulgaria)

    2013-12-16

    Biomimetic approach and subsequent high-temperature treatment were used to synthesize ion modified calcium phosphate fine powders. Thus, using Simulated Body Fluid (SBF) as an ion modifier, a bi-phase mixture of ion modified β-tricalcium phosphate and hydroxyapatite (β-TCP + HA) was prepared. The use of SBF electrolyte solution enriched with Mg{sup 2+} or Zn{sup 2+} yielded monophase β-tricalcium phosphate additionally modified with Mg{sup 2+} or Zn{sup 2+} (Mg-β-TCP or Zn-β-TCP). The in vitro behavior of the prepared powders on cell viability and proliferation of murine BALB/c 3T3 fibroblasts and of human Lep 3 cells was studied by MTT test assays and Mosmann method after 72 h incubation. The relative cell viability was calculated.

  8. Biomimetic synthesis of modified calcium phosphate fine powders and their in vitro studies

    International Nuclear Information System (INIS)

    Biomimetic approach and subsequent high-temperature treatment were used to synthesize ion modified calcium phosphate fine powders. Thus, using Simulated Body Fluid (SBF) as an ion modifier, a bi-phase mixture of ion modified β-tricalcium phosphate and hydroxyapatite (β-TCP + HA) was prepared. The use of SBF electrolyte solution enriched with Mg2+ or Zn2+ yielded monophase β-tricalcium phosphate additionally modified with Mg2+ or Zn2+ (Mg-β-TCP or Zn-β-TCP). The in vitro behavior of the prepared powders on cell viability and proliferation of murine BALB/c 3T3 fibroblasts and of human Lep 3 cells was studied by MTT test assays and Mosmann method after 72 h incubation. The relative cell viability was calculated

  9. Chemical synthesis and characterization of magnesium substituted amorphous calcium phosphate (MG-ACP)

    International Nuclear Information System (INIS)

    Amorphous calcium phosphate (ACP) was synthesized by a simple aqueous precipitation using CaCl2 and Na3PO4 in the presence of MgCl2 to ensure the formation of the ACP phase at room temperature. Magnesium substituted ACP phases corresponding to two different compositions representing the two most prominent calcium phosphate phases (hydroxyapatite: Ca + Mg/P = 1.67 and tricalcium phosphate: Ca + Mg/P = 1.5) were synthesized by this simple approach. Both compositions of ACP phases resulted in their transformation into β-tricalcium phosphate upon heat treatment in air at 600 deg. C. X-ray diffraction (XRD), heat treatment, scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) and Brunauer-Emmett-Teller (BET) analyses were used to characterize the phase, thermal stability, surface area, and morphology of the synthesized ACP powders corresponding to the two different nominal Ca/P compositions. Although it is known that α-TCP is the phase that appears upon heat treatment at 600 deg. C unsubstituted ACP, substitution of magnesium ion in ACP (both TCP and HA composition) stabilized the structure of β-TCMP phase at 600 deg. C. Moreover, FT-IR analysis revealed that the ACP phase regardless of the composition, exhibited characteristic bands corresponding to that of HA, with the exception of the ACP corresponding to HA composition which exhibited a prominent OH vibrational mode.

  10. Comparative study on in vivo response of porous calcium carbonate composite ceramic and biphasic calcium phosphate ceramic.

    Science.gov (United States)

    He, Fupo; Ren, Weiwei; Tian, Xiumei; Liu, Wei; Wu, Shanghua; Chen, Xiaoming

    2016-07-01

    In a previous study, robust calcium carbonate composite ceramics (CC/PG) were prepared by using phosphate-based glass (PG) as an additive, which showed good cell response. In the present study the in vivo response of porous CC/PG was compared to that of porous biphasic calcium phosphate ceramics (BCP), using a rabbit femoral critical-size grafting model. The materials degradation and bone formation processes were evaluated by general observation, X-ray radiography, micro-computed tomography, and histological examination. The results demonstrated excellent biocompatibility and osteoconductivity, and progressive degradation of CC/PG and BCP. Although the in vitro degradation rate of CC/PG was distinctly faster than that of BCP, at 4week post-implantation, the bone generation and material degradation of CC/PG were less than those of BCP. Nevertheless, at postoperative week 8, the increment of bone formation and material degradation of CC/PG was pronouncedly larger than that of BCP. These results show that CC/PG is a potential resorbable bone graft aside from the traditional synthetic ones. PMID:27127035

  11. Nanostructural Deformation Analysis of Calcium Silicate Hydrate in Portland Cement Paste by Atomic Pair Distribution Function

    Directory of Open Access Journals (Sweden)

    Hiroshi Suzuki

    2016-01-01

    Full Text Available The deformation of nanostructure of calcium silicate hydrate (C-S-H in Portland cement (PC paste under compression was characterized by the atomic pair distribution function (PDF, measured using synchrotron X-ray diffraction. The PDF of the PC paste exhibited a unique deformation behavior for a short-range order below 2.0 nm, close to the size of the C-S-H globule, while the deformation for a long-range order was similar to that of a calcium hydroxide phase measured by Bragg peak shift. The compressive deformation of the C-S-H nanostructure was comprised of three stages with different interactions between globules. This behavior would originate from the granular nature of C-S-H, which deforms with increasing packing density by slipping the interfaces between globules, rearranging the overall C-S-H nanostructure. This new approach will lead to increasing applications of the PDF technique to understand the deformation mechanism of C-S-H in PC-based materials.

  12. Synthesis and mechanical properties of a calcium sulphoaluminate cement made of industrial wastes

    Directory of Open Access Journals (Sweden)

    Gallardo, M.

    2014-09-01

    Full Text Available Environmentally-friendly calcium sulphoaluminate clinkers were obtained from a mixture of aluminium dross, fluorgypsum, fly ash and CaCO₃ at temperatures within the range of 1100 to 1400 °C. After the heat treatments Ca₄Al₆O₁₂SO₄ was the main phase. Three different cements were prepared using the clinkers synthesized at 1250, 1350 and 1400 °C; the clinker powders were mixed with 20 wt% of hemihydrate. Cement pastes were prepared using a water/cement ratio (w/c, 0.4 followed by curing at 20 or 40 °C for periods of time ranging from 1 to 28 days. Most of the samples showed high compression strengths 40–47 MPa after 28 days, which were comparable to the strength of Portland cement. Ettringite was the main hydration product and its morphology consisted of acicular and hexagonal plates, which is typical of this phase.Se fabricaron clinkers de bajo impacto ambiental a base de sulfoaluminato de calcio calcinando mezclas de escoria de aluminio, fluoryeso, ceniza volante y CaCO₃ a diferentes temperaturas dentro de un rango de 1100 a 1400 °C. Se observó la formación de Ca₄Al₆O₁₂SO₄ como fase principal. Para obtener los cementos, los clinkers obtenidos a 1250, 1350 y 1400 °C se mezclaron con 20% en peso de hemihidrato. Se prepararon pastas usando una relación agua/cemento, de 0.4 y se curaron a 20 y 40 °C por diferentes periodos de tiempo desde 1 hasta 28 días. Los valores de resistencia a la compresión a los 28 días de curado de la mayoría de las muestras estuvieron entre 40–47 MPa, equiparables a los de referencia de pastas de cemento Portland. La etringita fue el principal producto de hidratación y su morfología consistió de placas hexagonales y aciculares, típicas de esta fase.

  13. Pulsed electrodeposition for the synthesis of strontium-substituted calcium phosphate coatings with improved dissolution properties.

    Science.gov (United States)

    Drevet, Richard; Benhayoune, Hicham

    2013-10-01

    Strontium-substituted calcium phosphate coatings are synthesized by pulsed electrodeposition on titanium alloy (Ti6Al4V) substrates. Experimental conditions of the process are optimized in order to obtain a coating with a 5% atomic substitution of calcium by strontium which corresponds to the best observations on the osteoblast cells activity and on the osteoclast cells proliferation. The physical and chemical characterizations of the obtained coating are carried out by scanning electron microscopy associated to energy dispersive X-ray spectroscopy (EDXS) for X-ray microanalysis and the structural characterization of the coating is carried out by X-ray diffraction. The in vitro dissolution/precipitation properties of the coated substrates are investigated by immersion into Dulbecco's Modified Eagle Medium (DMEM) from 1h to 14 days. The calcium, phosphorus and strontium concentrations variations in the biological liquid are assessed by Induced Coupled Plasma - Atomic Emission Spectroscopy for each immersion time. The results show that under specific experimental conditions, the electrodeposition process is suitable to synthesize strontium-substituted calcium phosphate coatings. Moreover, the addition of hydrogen peroxide (H2O2) into the electrolytic solution used in the process allows us to observe a control of the strontium release during the immersion of the prosthetic materials into DMEM. PMID:23910341

  14. Reproducibility of the uptake of U(VI) onto degraded cement pastes and calcium silicate hydrate phases

    International Nuclear Information System (INIS)

    The U(VI) uptake in degraded cement pastes was undertaken in the laboratories of CEA/L3MR and SUBATECH in order to check the reproducibility of the study. Two well hydrated cement pastes, CEM I (ordinary portland cement, OPC) and CEM V (blast furnace slag (BFS) and fly ash added to OPC) were degraded using similar protocols. Equilibrium solutions and solid materials were characterised for three degradation states for each paste. All samples are free of portlandite and the pH of the equilibrated cement solutions vary in the range 9.8-12.2. Three calcium silicate hydrate phases (C-S-H) were synthesised in order to compare the sorption properties of degraded cement pastes and of hydrate phases in similar pH conditions. In order to avoid precipitation processes, the operational solubility limit was evaluated before batch experiments. These solubility values vary significantly in the pH range [9-13] with a 2.4 x 10-7 mol L-1 minimum at pH close to 10.5. In batch sorption experiments, the distribution ratio Rd values are high: 3 x 104 - 1.5 x 105 mL g-1. The uptake of U(VI) increases when comparing the least and the most degraded cement pastes whereas the initial composition of cement has relatively insensitive effect. Sorption isotherms, expressed as a log [U(VI)solid]/log[U(VI)solution] plots are linear. A slope of 1 is calculated indicating the predominance of sorption processes. As sorption and desorption values are close, the uptake mechanism seems reversible. The Rd values measured in C-S-H suspensions are in good agreement with Rd values of degraded cement pastes, and C-S-H materials could be one of the cementitious phases which control U(VI) uptake in cement pastes. (orig.)

  15. An inferred relationship between some uranium deposits and calcium carbonate cement in southern Black Hills, South Dakota

    Science.gov (United States)

    Gott, Garland B.

    1956-01-01

    Evidence resulting from geologic mapping in the southern Black Hills indicates that the areas marginal to some of the larger carbonate-cemented sandstones constitute favorable geochemical environments for the localization of uranium deposits. To determine whether these favorable environments are predictable a limited experimental core-drilling program was carried out. An extensive deposit was discovered in an area marginal to a sandstone well-cemented with calcium carbonate. The deposit has not yet been developed, but from the available data it appears that there is a significant quantity of mineralized rock present containing as much as 3.0 percent eU3O8.