WorldWideScience

Sample records for calcium hydroxides

  1. Analysis of barium hydroxide and calcium hydroxide slurry carbonation reactors

    Energy Technology Data Exchange (ETDEWEB)

    Patch, K.D.; Hart, R.P.; Schumacher, W.A.

    1980-05-01

    The removal of CO/sub 2/ from air was investigated by using a continuous-agitated-slurry carbonation reactor containing either barium hydroxide (Ba(OH)/sub 2/) or calcium hydroxide (Ca(OH)/sub 2/). Such a process would be applied to scrub /sup 14/CO/sub 2/ from stack gases at nuclear-fuel reprocessing plants. Decontamination factors were characterized for reactor conditions which could alter hydrodynamic behavior. An attempt was made to characterize reactor performance with models assuming both plug flow and various degrees of backmixing in the gas phase. The Ba(OH)/sub 2/ slurry enabled increased conversion, but apparently the process was controlled under some conditions by phenomena differing from those observed for carbonation by Ca(OH)/sub 2/. Overall reaction mechanisms are postulated.

  2. Effect of three different calcium hydroxide mixtures (calcium hydroxide with glycerine, normal saline and distilled water on root dentin microhardness

    Directory of Open Access Journals (Sweden)

    Hasheminia SM

    2007-06-01

    Full Text Available Background and Aim: During root canal therapy, it is necessary to remove as many bacteria as possible from the root canal. The use of medicaments is recommended to reduce the microbial population prior to root filling. Calcium hydroxide pastes have been used because of their antibacterial effects and the ability of tissue dissolving. The aim of this study was to evaluate the effect of calcium hydroxide/glycerine mixture, calcium hydroxide/normal saline mixture and calcium hydroxide/distilled water mixture on root dentin microhardness in storage times of 7 and 14 days.Materials and Methods: In this in vitro study, fifteen extracted maxillary canines and central incisors were selected. The crowns of the teeth were removed and the canals were prepared. Teeth were sectioned transversally to produce a total of 30 dentin discs from the middle third of the roots. Specimens were divided into three groups of 10 discs each. Dentin samples were subjected to calcium hydroxide/glycerine, calcium hydroxide/normal saline and calcium hydroxide/distilled water mixtures for 7 and 14 days. Dentin microhardness was measured by a Vickers indenter with a load of 200 g for 15 seconds. Data were analyzed using ANOVA, Paired t-test and LSD with p<0.05 as the level of significance.Results: Statistical analysis showed that all three mixtures decreased dentin microhardness. After 7 days, reduction in dentin microhardness by calcium hydroxide/glycerine combination was significantly higher than calcium hydroxide/normal saline and calcium hydroxide/distilled water combinations. After 14 days, reduction in dentin microhardness by calcium hydroxide/distilled water combination was significantly higher than the other two groups.Conclusion: Based on the results of this study, the use of calcium hydroxide combinations for intracanal dressing reduces dentin microhardness. After 7 days calcium hydroxide/glycerine combination and after 14 days calcium hydroxide/distilled water

  3. Pulp response to a novel adhesive calcium hydroxide based cement.

    Science.gov (United States)

    Watts, A; Paterson, R C; Cohen, B D; Combe, E C

    1994-09-01

    This study compares pulp responses to 3 formulations of calcium hydroxide, namely: a) An experimental adhesive calcium hydroxide cement containing polyacrylic acid, b) Dycal (L.D> Caulk Co, Milford, Delaware) Batch Nos 176970/176990, c) "Analar" calcium hydroxide mixed with sterile distilled water. After 28 days dentine bridges were present in 77% of teeth capped with the test material, 64% of teeth treated with Dycal and in 62% of teeth capped with calcium hydroxide and water. Inflammatory infiltrates were observed in a number of teeth remote from the bridges. Bacteria were detected in these specimens. Exposed rat molar pulp responses to an experimental adhesive calcium hydroxide cement were similar to to those observed with 2 other calcium hydroxide formulations.

  4. Role of Calcium Hydroxide in Endodontics: A Review

    OpenAIRE

    Arun A; Sangameshwar Sajjanshetty; Deepak Jain; Saujanya KP; Mohammed Mustafa; Laxmi Uppin; Mahnoor Kadri

    2012-01-01

    Calcium hydroxide is a multipurpose agent, and there have been an increasing number of indications for its use in endodontics. Some of its indications include inter-appointment intracanal medicaments, endodontic sealers, pulp capping agents, apexification, pulpotomy and weeping canals. The purpose of this article is to review the properties, advantages, disadvantages and various indications for the use of calcium hydroxide in endodontics.

  5. 21 CFR 872.3250 - Calcium hydroxide cavity liner.

    Science.gov (United States)

    2010-04-01

    ... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3250 Calcium hydroxide cavity liner. (a) Identification. A calcium hydroxide cavity liner is a device material intended to be applied to the interior of a prepared cavity before insertion of restorative material, such as amalgam, to protect the pulp of a...

  6. Tertiary dentinogenesis with calcium hydroxide: a review of proposed mechanisms.

    Science.gov (United States)

    Sangwan, P; Sangwan, A; Duhan, J; Rohilla, A

    2013-01-01

    Calcium hydroxide has been used extensively in dentistry for a century. Despite its widespread use as a pulp-capping agent, its mechanisms of action still remain ambiguous. Understanding its modes of action will lead to a broader understanding of the mechanisms associated with induced dentinogenesis and help in optimizing the currently available agents to target specific regenerative processes to obtain the best possible clinical outcomes. A literature search relating to mechanisms of dentinogenesis of calcium hydroxide up to December 2011 was carried out using pubmed and MEDLINE database searches as well as manual searching of cross-references from identified studies. Resulting suggestions regarding dentinogenic mechanisms of calcium hydroxide range from direct irritating action of the material to induction of release of biologically active molecules. The purpose of this article is to discuss various mechanisms through which calcium hydroxide may induce tertiary dentinogenesis in the light of observations made in included studies.

  7. Role of Calcium Hydroxide in Endodontics: A Review

    Directory of Open Access Journals (Sweden)

    Arun A

    2012-01-01

    Full Text Available Calcium hydroxide is a multipurpose agent, and there have been an increasing number of indications for its use in endodontics. Some of its indications include inter-appointment intracanal medicaments, endodontic sealers, pulp capping agents, apexification, pulpotomy and weeping canals. The purpose of this article is to review the properties, advantages, disadvantages and various indications for the use of calcium hydroxide in endodontics.

  8. The citotoxicity of calcium hydroxide intracanal dressing by MTT assay

    Directory of Open Access Journals (Sweden)

    Nanik Zubaidah

    2007-12-01

    Full Text Available Calcium hydroxide had been used as the intracanal dressing in endodontic treatment due to its high alkaline and high antimicrobial capacity. It also be able to dissolve the necrotic tissue, prevent the root resorbtion and regenerate a new hard tissue. The aim of this study is to identify the concentration of calcium hydroxide that has the lowest citotoxicity. There are 5 groups, each group had 8 samples with different concentration of calcium hydroxide. Group I: 50%, Group II: 55%, Group III: 60%, Group IV: 65% and Group V: 70%. The citotoxicity test by using enzymatic assay of MTT [3-(4.5- dimethylthiazol-2yl ]-2.5 diphenyl tetrazolium bromide, against fibroblast cell (BHK-21. The result of susceptibility test was showed by the citotoxicity detection of the survive cell of fibroblast that was measured spectrophotometrically using 595 nm beam. The data was analyzed using One-Way ANOVA test with significant difference α = 0.05 and subsequently LSD test. The result showed that in concentration 50%, 55%, 60%, 65%, and 70% calcium hydroxide had low toxicity, but calcium hydroxide 60%, had the lowest toxicity.

  9. Thermochemistry of calcium oxide and calcium hydroxide in fluoride slags

    Science.gov (United States)

    Chattopadhyay, S.; Mitchell, A.

    1990-08-01

    Calcium oxide activity in binary CaF2-CaO and ternary CaF2-CaO-Al2O3 and CaF2-CaO-SiO2 slags has been determined by CO2-slag equilibrium experiments at 1400 °C. The carbonate ca-pacity of these slags has also been computed and compared with sulfide capacity data available in the literature. The similarity in trends suggests the possibility of characterizing carbonate capacity as an alternative basicity index for fluoride-base slags. Slag-D2O equilibrium experi-ments are performed at 1400°C with different fluoride-base slags to determine water solubility at two different partial pressures of D2O, employing a new slag sampling technique. A novel isotope tracer detection technique is employed to analyze water in the slags. The water solubility data found show higher values than the previous literature data by an order of magnitude but show a linear relationship with the square root of water vapor partial pressure. The activity of hydroxide computed from the data is shown to be helpful in estimating water solubility in in-dustrial electroslag remelting (ESR) slags.

  10. ANTIBACTERIAL EFFECT OF CALCIUM HYDROXIDE IN DIFFER ENT VEHICLES

    Directory of Open Access Journals (Sweden)

    Hari

    2012-11-01

    Full Text Available ABSTRACT: AIM: This study evaluated the antibacterial effect of ca lcium hydroxide in different vehicles in an in vitro model. MATERIAL AND METHODS: Calcium hydroxide paste prepared with two conventionally used vehicles namely, campho rated monochlophenol, distilled water and also propylene glycol. The antibacterial activity of these paste were tested against five micro- organisms that can commonly occur in the inf ected root canals. RESULTS AND CONCLUSIONS: The results of the study indicate that a paste of ca lcium hydroxide made with propylene glycol exerts significant antibacterial act ion. Hence, it can be recommended for use as an intracanal medicament in preference to a paste prepa red with a tissue toxic phenolic compound like camphorated mono chlorophenol

  11. CALCIUM HYDROXIDE IN ENDODONTIC TREATMENT OF PERIAPICALLY INFECTED TEETH

    Directory of Open Access Journals (Sweden)

    Rahmi Alma Farah Adang

    2006-04-01

    Full Text Available An inadequate endodontic treatment may affect the root canal system and spread beyond its apical foramina that elicit periodontal tissue developing into abscess, granuloma and radicular cyst. Periodical lesions can be treated with non surgical endodontic treatment using calcium hydroxide dressing. This case study is reporting teeth 11 with periodical lesions and infection. Evidence of a clinical healing and radiographic assessments were followed by a non surgical endodontic therapy. Successful treatment outcome is related to the elimination of infection agents from the root canal. This can activate a stimulation zone to promote regeneration. Calcium hydroxide used as a root canal dressing may promote alkalinity at the adjacent tissue , create favourable environmental condition in which hard tissue formation can occur, interfere the bactericidal activity, increase mineralization, and induce healing.

  12. Antimicrobial activity of calcium hydroxide and chlorhexidine on intratubular Candida albicans

    Institute of Scientific and Technical Information of China (English)

    Ronan Jacques Rezende Delgado; Thaís Helena Gasparoto; Carla Renata Sipert; Claudia Ramos Pinheiro; Ivaldo Gomes de Moraes; Roberto Brandāo Garcia; Marco Antonio Hungaro Duarte; Clóvis Monteiro Bramante; Sérgio Aparecido Torres; Gustavo Pompermaier Garlet; Ana Paula Campanelli; Norberti Bernardineli

    2013-01-01

    This study investigated the efficacy of calcium hydroxide and chlorhexidine gel for the elimination of intratubular Candida albicans (C. albicans). Human single-rooted teeth contaminated with C. albicans were treated with calcium hydroxide, 2% chlorhexidine gel, calcium hydroxide plus 2% chlorhexidine gel, or saline (0.9% sodium chloride) as a positive control. The samples obtained at depths of 0-100 and 100-200 μm from the root canal system were analyzed for C. albicans load by counting the number of colony forming units and for the percentage of viable C. albicans using fluorescence microscopy. First, the antimicrobial activity of calcium hydroxide and the 2% chlorhexidine gel was evaluated by counting the number of colony forming units. After 14 days of intracanal medication, there was a significant decrease in the number of C. albicanscolony forming units at a depth of 0-100 lzm with chlorhexidine treatment either with or without calcium hydroxide compared with the calcium hydroxide only treatment. However, there were no differences in the number of colony forming units at the 100-200 μm depth for any of the medications investigated. C. albicans viability was also evaluated by vital staining techniques and fluorescence microscopy analysis. Antifungal activity against C. albicans significantly increased at both depths in the chlorhexidine groups with and without calcium hydroxide compared with the groups treated with calcium hydroxide only. Treatments with only chlorhexidine or chlorhexidine in combination with calcium hydroxide were effective for elimination of C. albicans.

  13. Assessment of ion diffusion from a calcium hydroxide-propolis paste through dentin

    Directory of Open Access Journals (Sweden)

    Janaina Corazza Montero

    2012-08-01

    Full Text Available This study evaluated the ability of ions from a non-alcoholic calcium hydroxide-propolis paste to diffuse through dentinal tubules. Thirty-six single-rooted bovine teeth were used. The tooth crowns were removed, and the root canals were instrumented and divided into 3 groups: Group 1 - calcium hydroxide-propylene glycol paste; Group 2 - calcium hydroxide-saline solution paste; Group 3 - calcium hydroxide-propolis paste. After the root canal dressings were applied, the teeth were sealed and placed in containers with deionized water. The pH of the water was measured after 3, 24, 72 and 168 hours to determine the diffusion of calcium hydroxide ions through the dentinal tubules. All of the pastes studied promoted the diffusion of calcium hydroxide ions through the dentinal tubules. Associating propolis to calcium hydroxide resulted in a pH increase, which occurred with greater intensity after 72 hours. The calcium hydroxide-propolis paste was able to diffuse in dentin.

  14. Comparison of calcium hydroxide and zinc oxide and eugenol pulpectomies in primary teeth of dogs.

    Science.gov (United States)

    Hendry, J A; Jeansonne, B G; Dummett, C O; Burrell, W

    1982-10-01

    The purpose of this investigation was to compare calcium hydroxide with zinc oxide and eugenol (ZOE) as root canal obturants in the pulpectomy procedure for irreversibly inflamed primary pulps of dogs. Clinical, radiographic, and histologic comparisons of calcium hydroxide and ZOE root canal filling materials were made in forty-two primary premolars of seven mongrel puppies. When the animals were 6 weeks of age, the pulps of all samples teeth were extirpated and the canals left open to the oral environment. The root canals were assigned to calcium hydroxide, ZOE, and control groups, instrumented, and filled 2 weeks later. The animals were killed 1 day, 1 week, 4 weeks, and 12 weeks after filling. Statistical analysis of all categories for comparison at 4 weeks indicated that calcium hydroxide gave significantly more favorable results than ZOE. Canals treated with calcium hydroxide exhibited less inflammation, less resorption, and more hard-tissue apposition than ZOE-treated and control groups.

  15. Application of Hydrosoluble Polymers to Preparation of Nanoscale Calcium Hydroxide

    Institute of Scientific and Technical Information of China (English)

    XU Jing; CHEN Qing-hua; QIAN Qing-rong

    2004-01-01

    Calcium hydroxide with uniform diameters about 50-100 nm was firstly prepared under moderate condition by adding different kinds of hydrosoluble polymers. From the results of TEM and IR, the polymers were proved not only to improve the agglomeration of the nanoparticles but also to be used as a template to control the formation of the special structure and the needed size of Ca (OH)2 by changing the concentration of the polymers. The experimental results of TG-DTA indicate that the Ca(OH)2 can absorb most of the acid gases released during the decomposition of polymers. So this kind of nano-Ca(OH)2 can be used as a useful additive of environmental friendly plastics.

  16. Evaluation of antibacterial effects of different calcium hydroxide compositions on planktonic Enterococcus faecalis

    Directory of Open Access Journals (Sweden)

    Mahdi Tabrizizadeh

    2012-01-01

    Full Text Available Background and Aims: Calcium hydroxide has a pronounced antimicrobial activity against most of the bacterial species found in infected root canals and endodontic infections. It is one of the most frequently used intracanal medications in endodontic therapy. The objective of this study was to determine the antimicrobial efficacy of six calcium hydroxide formulations (mixed with saline, lidocaine 2%, chlorhexidine 2%, chlorhexidine 0.2%, Iodine Potassium iodide (IKI 2%, and glycerin on Enterococcus faecalis using agar diffusion test.Materials and Methods: Twelve culture plates were incubated with Enterococcus faecalis. Five cavities were made in each plate with 5 mm diameter and 4 mm depth. Two plates were randomly considered for each calcium hydroxide formulation and filled completely with creamy mixture of tested materials. The plates were incubated at 37ºC for 48 hours. The diameter of inhibition zone around each well was recorded in millimetres and data were submitted to ANOVA and Tukey tests.Results: The results of this study showed that all tested calcium hydroxide pastes had good antimicrobial activity. The antimicrobial activity of calcium hydroxide mixed with lidocaine, chlorhexidine 2% and IKI 2% were significantly greater than that of calcium hydroxide mixed with saline (P0.01.Conclusion: Considering the results of this study, lidocaine 2%, chlorhexidine 2% and IKI 2% are suggested to be used for preparation of calcium hydroxide paste. Further studies with different methods are needed for confirming these results.

  17. Antimicrobial effect of calcium hydroxide as endo intracanal dressing on Streptococcus viridans

    Directory of Open Access Journals (Sweden)

    Nanik Zubaidah

    2008-03-01

    Full Text Available Calcium hydroxide had been used as the intra-canal dressing in endodontic treatment due to its high alkaline and antimicrobial capacity. It can also dissolve the necrotic tissue, prevent dental root resorbtion and regenerate a new hard tissue. The aim of this study was to determine the concentration of calcium hydroxide which had the highest antimicrobial effect on Streptococcus viridans. Samples were divided into 5 groups; each group consisted of 8 samples with different concentration of calcium hydroxide. Group I: 50%, group II: 55, Group III: 60%, Group IV: 65%, Group V: 70%. The antimicrobial testing was performed using diffusion method against Streptococcus viridans. The result of susceptibility test was showed by the inhibition zone diameter which measured with caliper (in millimeter. We analyzed the data using One-Way ANOVA test with significant difference 0.05 and subsequently LSD test. The study showed that calcium hydroxide with concentration 60% has the highest antimicrobial effect.

  18. Effects of aluminum hydroxide and calcium carbonate antacids on the bioavailability of ciprofloxacin.

    OpenAIRE

    Frost, R W; Lasseter, K C; Noe, A J; Shamblen, E C; Lettieri, J T

    1992-01-01

    This study was designed to determine the effects of an aluminum hydroxide antacid and a calcium carbonate antacid on the bioavailability of ciprofloxacin (Cipro). Cipro (750 mg) was administered orally to 12 healthy volunteers in a three-way randomized crossover design. The three treatments included Cipro alone, four 850-mg calcium carbonate tablets taken 5 min before Cipro, and three 600-mg aluminum hydroxide tablets taken 5 min before Cipro. The relative bioavailability of Cipro when given ...

  19. The Effect of Calcium Hydroxide As an Intracanal Medication of The Apical Microleakage

    Directory of Open Access Journals (Sweden)

    Heshmat Mohajer AR

    2011-12-01

    Full Text Available Background and Aims: Nowadays, calcium hydroxide is used as a dressing for canal sterilization and repair progression of apical lesions. The aim of this study was to investigate the effect of calcium hydroxide as an intracanal medicament on the apical microleakage of root filling.Materials and Methods: In this experimental study, 46 extracted single-rooted human teeth were instrumented with step-back technique to master apical file (MAF size 35. Specimens were randomly divided into 2 groups (n = 20. In group 1, the specimens were treated with calcium hydroxide intracanal medication; and in group 2, the samples did not receive any medication. The teeth were incubated in 100% humidity at 37°C for one week. After that, calcium hydroxide was removed using irrigation with normal saline and reaming with MAF. The root canals were obturated with gutta- percha and AH26 sealer using lateral compaction technique. Specimens were incubated in 100% humility at 37°C for 72 hours and then immersed in India ink for 1 week. Finally, the teeth were cleared and the maximum linear dye penetration was measured under a stereomicroscope at 4X magnification. The data were analyzed by T-test and Chi-square.Results: There was no significant difference between the two experimental groups (P=0.068. Conclusion: The findings of this study indicated that using calcium hydroxide as an intracanal medicament did not influence the apical microleakage after final obturation of the root canal system.

  20. Relationship between sealing ability of Activ GP and Gutta Flow and methods of calcium hydroxide removal

    Directory of Open Access Journals (Sweden)

    Vineeta Nikhil

    2012-01-01

    Full Text Available Aim: To evaluate the effect of method of calcium hydroxide intracanal dressing removal, on sealing ability of Gutta Flow and Activ GP. Materials and Methods: Seventy extracted mandibular premolars were sectioned at CEJ and canals were prepared with profile 4% rotary file till #40. Canals were filled with calcium hydroxide, coronally sealed with Cavit G and stored at 37°C. After 7 days, samples were divided on the basis of calcium hydroxide removal method (Master apical file, Navi Tip FX, and F File and obturating material (Activ GP and Gutta Flow. Three coats of nail polish were applied except 2 mm around apical foramen and samples were immersed in India ink dye, sectioned, and observed under stereomicroscope for microleakage. Results: The results were statistically analyzed with one way ANOVA-F with Tukey HSD test with the null hypothesis set as 5%. Conclusions: The seal of the canal system was adversely impacted by residual calcium hydroxide when Activ GP and Gutta Flow were used as obturating material and the sealing ability of Activ GP and Gutta Flow was better when MAF was used for removal of calcium hydroxide than F file or Navi tip FX.

  1. COMPARATIVE EVALUATION OF THE ANTIBACTERIAL EFFECT OF CALCIUM HYDROXIDE PASTES USING FOUR DIFFERENT VEHIC LES

    Directory of Open Access Journals (Sweden)

    Ganesh

    2012-10-01

    Full Text Available ABSTRACT: AIM: The present study evaluated the antibacterial effec t of calcium hydroxide pastes using four different vehicles namely propylene glycol, glycerin, distilled water and camphorated phenol. MATERIAL AND METHOD: Calcium hydroxide pastes prepared with two commonly used vehicles namely distilled water and c amphorated phenol. The antibacterial activity of these pastes were tested against five a naerobic organism that can commonly occur in the infected root canal. The pastes were also prepare d using two chemicals such as propylene glycol and glycerin. RESULTS AND CONCLUSION: The result of this study show that calcium hydroxide paste made with propylene glycol gives enhan ced antibacterial action and sustains it for longer period of time. Propylene glycol being bi ological acceptable vehicle, it can be recommended for routine use as a vehicle over glyce rin

  2. A role for calcium hydroxide and dolomite in water: acceleration of the reaction under ultraviolet light.

    Science.gov (United States)

    Nagase, Hiroyasu; Tsujino, Hidekazu; Kurihara, Daisuke; Saito, Hiroshi; Kawase, Masaya

    2014-04-01

    Organic environmental pollutants are now being detected with remarkably high frequency in the aquatic environment. Photodegradation by ultraviolet light is sometimes used as a method for removing organic chemicals from water; however, this method is relatively inefficient because of the low degradation rates involved, and more efficient methods are under development. Here we show that the removal of various organic pollutants can be assisted by calcined dolomite in aqueous solution under irradiation with ultraviolet light. It was possible to achieve substantial removal of bisphenol A, chlorophenols, alkylphenols, 1-naphthol and 17β-estradiol. The major component of dolomite responsible for the removal was calcium hydroxide. Our results demonstrate that the use of calcium hydroxide with ultraviolet light irradiation can be a very effective method of rapidly removing organic environmental pollutants from water. This is a new role for calcium hydroxide and dolomite in water treatment.

  3. Production of Potassium and Calcium Hydroxide, Compost and Humic Acid from Sago (Metroxylon sagu Waste

    Directory of Open Access Journals (Sweden)

    C. P. Auldry

    2009-01-01

    Full Text Available Problem statement: Agriculture waste such as Sago Waste (SW has a potential to cause pollution when the waste is discarded into rivers. In order to add value to SW, a study was conducted to produce potassium and calcium hydroxide, compost and Humic Acid (HA from SW. Approach: The SW was air-dried and some grinded. The grinded SW was incinerated at 600°C. Potassium and calcium hydroxide was extracted by dissolving the ash in distilled water at a ratio of 1:500 (ash: water, equilibrated for 24 h at 150 rpm using a mechanical shaker and filtered. The ungrinded SW was used for compost production. The compost was produced by mixing SW (80% + chicken feed (10% + chicken dung slurry (5% + molasses (5%. Results: The hydroxide extracted from ash of SW was used to isolate HA of composted SW. The molarity and pH of the hydroxide were 0.002M and 10 respectively. Calcium (42.88 mg kg-1 and potassium (29.51 mg kg-1 content were high in the hydroxide compared with other elements. The compost took about 60 days to mature. There was an increased in pH, ash, Cation Exchange Capacity (CEC and HA and a decreased in temperature, C/N ratio, C/P ratio and organic matter. The hydroxide was able to extract 1% of HA from the composted SW. A comparison between the yields of HA extracted from the composted SW using the hydroxide of the SW and that of the analytical grade showed no statistically difference. The chemical characteristics of HA from the composted SW were in standard range. Conclusion: Potassium and calcium hydroxide, compost and HA can be produced from sago waste. Low morality of the hydroxide is able to produce good quality of HA from composted sago waste. The HA can be reconstituted with K and Ca from potassium and calcium hydroxide to produce K-Ca-humate and this needs to be investigated as a form of organic based fertilizer.

  4. Evaluation of calcium ion release and change in pH on combining calcium hydroxide with different vehicles

    Directory of Open Access Journals (Sweden)

    Charu Grover

    2014-01-01

    Full Text Available Introduction: Intracanal medicaments have traditionally been used in endodontics to disinfect root canals between appointments. Calcium hydroxide is widely used as an intracanal medicament for disinfection and to promote periapical healing. It is stable for long periods, harmless to the body, and bactericidal in a limited area. The efficacy of calcium hydroxide as a disinfectant is dependent on the availability of the hydroxyl ions in the solution that depends on the vehicle in which the calcium hydroxide is carried. In general, three types of vehicles are used: Aqueous, viscous or oily. Some in vitro studies have shown that the type of vehicle has a direct relationship with the concentration and the velocity of ionic liberation as well as with the antibacterial action when the paste is carried into a contaminated area. Aim of the Study: To evaluate the calcium ion release and measure the change in pH of the environment that occurred when calcium hydroxide was combined with different vehicles (distilled water, propylene glycol, calcium hydroxide containing gutta-percha points and chitosan over different time periods. Materials and Methods: Forty single rooted mandibular first premolar teeth were decoronated for this study. Working length was established and the root canals were enlarged and irrigation accomplished with 2 ml of NaOCl solution after every file. The teeth were then randomly divided into four groups. The canals were then packed with different preparations of calcium hydroxide using the following vehicles-distilled water, propylene glycol, gutta-percha points and chitosan. Calcium ion release in different groups was analyzed using an ultraviolet spectrophotometer at 220 nm. The change in pH of was determined using a pH meter. Results were statistically evaluated using one-way ANOVA test. Result: For calcium ion release, Group 2 showed cumulative drug release of 81.97% at the end of 15 days, whereas Group 1, 3 and 4 showed a release

  5. Ion Association versus Ion Interaction Models in Examining Electrolyte Solutions: Application to Calcium Hydroxide Solubility Equilibrium

    Science.gov (United States)

    Menéndez, M. Isabel; Borge, Javier

    2014-01-01

    The heterogeneous equilibrium of the solubility of calcium hydroxide in water is used to predict both its solubility product from solubility and solubility values from solubility product when inert salts, in any concentration, are present. Accepting the necessity of including activity coefficients to treat the saturated solution of calcium…

  6. Comparison of Calcium Hydroxide and Bioactive Glass after Direct Pulp Capping in Primary Teeth

    Directory of Open Access Journals (Sweden)

    R. Haghgoo

    2007-12-01

    Full Text Available Objective: Bioactive glass is often used as a filler material for repair of dental bone defects.In different studies osteogenic potential of this material was proved, but its dentinogenesisproperty is in doubt. The purpose of this study was to evaluate the histological pulp responses of Calcium hydroxide and Bioactive glass placed directly on exposed pulp tissues.Materials and Methods: Twenty teeth to be extracted due to orthodontic reasons were selected. These teeth were divided into two groups and treated with direct pulp capping.Calcium hydroxide was used for 10 teeth and Bioactive glass for 10 teeth. After 60 daysthe teeth were extracted and prepared for histological evaluation. Finally the data was analyzed with exact Fisher test.Results: All teeth treated with Calcium hydroxide showed inflammation. Internal resorption was seen in six teeth, abscess in five teeth and dentinal bridge in two teeth. Inflammationwas seen in three Bioactive glass samples and dentinal bridge in seven teeth, but internal resorption and abscess were not seen.Conclusion: Bioactive glass appears to be superior to Calcium hydroxide as a pulp capping agent in primary teeth.

  7. Clinical Survey of Successfulness of DPC with MTA and Calcium Hydroxide

    Directory of Open Access Journals (Sweden)

    E.Yasini

    2005-02-01

    Full Text Available Statement of Problem: The pulp may be exposed during remove of caries or by traumatic and iatrogenicinjuries. The material used to DPC, must be biocompatible, scalable and prevent bacterial leakage.Furthermore, it is better to stimulate dentinogenesis. Calcium hydroxide is most usual material for DPC. But itcannot provide a suitablcbiologic seal. Mineral irioxide aggregate (MTA is also a suitable material for DPC.Purpose: The aim of this study was to compare the clinical success of DPC done with MTA or calciumhydroxide cement.Materials and Methods: In this study eighteen posterior teeth without previous spontaneous pain thatinvolved mechanicaly exposure was randomly selected and capped with MTA or calcium hydroxide. These teeth were evaluated by clinical vitality test and radiograph after 3 and 12 months, and patients werequestioned about irritative or spontancus pain in this period. Statistical analysis was carried out by Usher exacttest (a-0.05.Results: This study showed that in calcium hydroxid groud three had irreversible pulpitis and two teeth had symptom and signs of reversible pulpitis. While, In MTA group all cases were normaL and no clinical sign was evident.Conclusion: MTA exhibited better results than calcium hydroxide cement for the capping of the pulp in human

  8. Effect of the smear layer in the removal of calcium hydroxide from root canal walls

    Directory of Open Access Journals (Sweden)

    Hakan Arslan

    2012-01-01

    Full Text Available Background: The aim of this study was to investigate whether the smear layer influences the removal of calcium hydroxide from the root canal with manual or rotary instruments. Materials and Methods: The root canals of 48 freshly extracted single-rooted maxillary incisors were prepared to apical size 40 (n=40 and finally irrigated with sodium hypochlorite (group A, or ethylene diamine tetra acetic acid (EDTA followed by sodium hypo chlorite (group B. 20 teeth were assigned to each group, while the remaining eight teeth served as positive and negative controls. Each group was divided into two subgroups of 10 teeth (subgroup I - calcium hydroxide was removed with master apical file; subgroup II - with profile file; and, in all removal procedures, citric acid was used for irrigation. The percentage of calcium hydroxide-[Ca(OH [Ca(OH 2 ] coated surface area was calculated by image processing analysis. Results: Considering the root canal as a whole, the removal of Ca(OH 2 from the dentinal walls in group B showed significantly better results (P<0.05 as compared to group A. Conclusions: Under the conditions of this study, it can be concluded that the smear layer is important in the removal of calcium hydroxide.

  9. Effect of supplementation with barley and calcium hydroxide on intake of Mediterranean shrubs

    Directory of Open Access Journals (Sweden)

    Dragan Skobic

    2011-04-01

    Full Text Available Maquis plant communities are one of the most varied vegetation types in the Mediterranean region and an important habitat for wild and domestic herbivores. Although the majority of these shrubs are nutritious, the secondary compounds are main impediments that reduce their forage value. In five experiments we determined the effect of supplementing goats with calcium hydroxide plus barley, and barley alone on intake of five dominant shrubs (Quercus ilex, Erica multiflora, Arbutus unedo, Viburnum tinus and Pistacia lentiscus of the Mediterranean maquis community. The combination of calcium hydroxide plus barley and barley alone increased utilization of all five investigated Mediterranean shrubs; therewith that intake of Arbutus unedo and Viburnum tinus was not statistically significant. Supplemented goats with calcium hydroxide plus barley or barley alone could be effective in controlling secondary compounds-rich Mediterranean shrubs where their abundance threatens biodiversity. This control can be facilitated by browsing dominant Mediterranean shrubs, which has been shown to be effective in managing Mediterranean maquis density. Calcium hydroxide and barley (energy enhance use of secondary compounds-containing plants, which may increase production of alternate forages and create a more diverse mix of plant species in the Mediterranean maquis plant community.

  10. Raman Study on Pompeii Potteries: The Role of Calcium Hydroxide on the Surface Treatment

    Directory of Open Access Journals (Sweden)

    Daniele Chiriu

    2014-01-01

    Full Text Available Pottery samples from the Pompeii archaeological site were investigated by IR Raman spectroscopy and EDAX measurements. The analysis of the Raman spectra of the surfaces reveals the presence calcium hydroxide (peak at about 780 cm−1 while the calcium carbonate is totally absent. The comparative studies on the carbonation effect of the surfaces were performed on laboratory grown samples of calcium hydroxide. The samples were treated at high temperature and exposed to different ambient conditions, and the analysis suggests that the original surfaces of Roman pottery were scattered by calcium hydroxide (limewash before the cooking process in the furnace. The result of this surface treatment not only permits a vitrification of the surfaces but also seems to reduce the content of CO2 in the furnace atmosphere and then obtain a more oxidant ambient during the cooking of the pottery. These results give new insights on the real degree of knowledge of the Romans about the art of ceramics and more generally about chemistry and technologies.

  11. Chemical analysis of the liberation of calcium and hydroxyl ions from calcium hydroxide pastes in connective tissue in the dog--Part I.

    Science.gov (United States)

    Estrela, C; Pesce, H F

    1996-01-01

    The objective of this research is to chemically analyze calcium hydroxide pastes added to three hydrosoluble vehicles having different acid-base characteristics using polyethylene tubes implanted in subcutaneous connective tissue in a dog, evaluating the liberation of calcium and hydroxyl ions over a period of 7, 30, 45 and 60 days. The three vehicles were saline, anesthetic, and polyethylene glycol 400. Chemical analysis of the liberated calcium ions was done by means of conductimetry using EDTA for titration. Liberation of hydroxyl ions was determined by analogy of calcium ions liberated, which are in direct proportion to the molecular weight of calcium hydroxide.

  12. Alcohol dispersions of calcium hydroxide nanoparticles for stone conservation.

    Science.gov (United States)

    Rodriguez-Navarro, Carlos; Suzuki, Amelia; Ruiz-Agudo, Encarnacion

    2013-09-10

    Alcohol dispersions of Ca(OH)2 nanoparticles, the so-called nanolimes, are emerging as an effective conservation material for the consolidation of stone, mortars, and plasters present in old masonry and/or mural paintings. To better understand how this treatment operates, to optimize its performance and broaden its applications, here we study the nano and microstructural characteristics, carbonation behavior, and consolidation efficacy of colloidal alcohol dispersions of Ca(OH)2 nanoparticles produced by both homogeneous (commercial nanolime) and heterogeneous phase synthesis (aged slaked lime and carbide lime putties). We observe that the alcohol not only provides a high colloidal stability to Ca(OH)2 particles, but also affects the kinetics of carbonation and CaCO3 polymorph selection. This is due to the pseudomorphic replacement of Ca(OH)2 particles by calcium alkoxides upon reaction with ethanol or 2-propanol. The extent of this replacement reaction depends on Ca(OH)2 size and time. Hydrolysis of alkoxides speeds up the carbonation process and increases the CaCO3 yield. The higher degree of transformation into calcium alkoxide of both the commercial nanolime and the carbide lime fosters metastable vaterite formation, while calcite precipitation is promoted upon carbonation of the aged slaked lime due its lower reactivity, which limits calcium alkoxide formation. A higher consolidation efficacy in terms of strength gain of treated porous stone is achieved in the latter case, despite the fact that the carbonation is much faster and reaches a higher yield in the former ones. Formation of alkoxides, which has been neglected in previous studies, needs to be considered when applying nanolime treatments. These results show that the use Ca(OH)2 nanoparticle dispersions prepared with either aged slaked lime or carbide lime putties is an economical and effective conservation alternative to commercial nanolimes produced by homogeneous phase synthesis. Ultimately, this

  13. A comparative study on dental pulp response to calcium hydroxide, white and grey mineral trioxide aggregate as pulp capping agents

    Directory of Open Access Journals (Sweden)

    Ali Eskandarizadeh

    2011-01-01

    Conclusions : Based on the result of this study, both types of MTA can be suggested as the materials of choice for direct pulp capping procedure instead of Dycal as hard setting calcium hydroxide cement.

  14. Nanoparticles for cultural heritage conservation: calcium and barium hydroxide nanoparticles for wall painting consolidation.

    Science.gov (United States)

    Giorgi, Rodorico; Ambrosi, Moira; Toccafondi, Nicola; Baglioni, Piero

    2010-08-16

    Nanotechnology provides new concepts and materials for the consolidation and protection of wall paintings. In particular, humble calcium and barium hydroxide nanoparticles offer a versatile and highly efficient tool to combat the main degradation processes altering wall paintings. Clear example of the efficacy and potentiality of nanotechnology is represented by the conservation in situ of Maya wall paintings in the archaeological area in Calakmul (Mexico).

  15. Vertical root fracture associated with prolonged use of calcium hydroxide during apexification. A case report.

    Directory of Open Access Journals (Sweden)

    Jennifer Ribadeneira

    2015-04-01

    Full Text Available Apexification is a procedure performed in young permanent teeth to promote apical closure and root elongation if Hertwig’s epithelial sheath has not been irreversibly damaged. The objective of this article is to describe vertical root fracture as a complication during apexification when using calcium hydroxide for extended periods of time. The patient was a 9-year-old female student who went to the Faculty of Dentistry of the Universidad Andres Bello in Concepcion. She presented strong and spontaneous pain and pressure and swelling on the left cheek. Clinically, the vestibule of the lower left first molar (3.6 was edematous and had pus. Radiographically, lesions and open apices were seen in the apical zone. Diagnosis was pulp necrosis and acute apical abscess. The tooth was trephined to perform intracanal drainage and an oral antibiotic was prescribed. Afterwards, she was referred to the endodontic specialty office. The selected treatment was apexification with calcium hydroxide until achieving the formation of an apical barrier. When the apical formation was observed, a vertical root fracture was discovered as well, confirming that the use of calcium hydroxide should not be prolonged because dehydration processes lead to weakening of the walls and therefore of the tooth

  16. Adaptation of two different calcium hydroxide bases under a composite restoration.

    Science.gov (United States)

    Papadakou, M; Barnes, I E; Wassell, R W; McCabe, J F

    1990-10-01

    A preliminary scanning electron microscope (SEM) study was carried out to investigate how the adaptation of two calcium hydroxide bases (one chemically cured, one light cured) was affected by the polymerization contraction of a supervening light-cured composite resin restoration. Occlusal cavities were prepared in 40 sound extracted human premolars, divided into two equal groups. In the first group a chemically cured calcium hydroxide (Dycal, De Trey Dentsply, Konstanz, FRG) was placed as a base. In the second group a new light-cured calcium hydroxide product (Prisma VLC Dycal, De Trey Dentsply) was used. The restorations were completed with an acid-etched, incrementally placed composite resin. The specimens were sectioned vertically and debrided. A replica was made of each half-tooth. The interfaces between composite resin/base and base/dentine were viewed and photographed in the SEM. The marginal adaptation at these two interfaces was classified into three categories according to the extent of the gaps that were observed. Prisma VLC Dycal base was found to be pulled away from the dentine floor of the cavity as a result of an apparent adhesion to the composite resin during polymerization contraction. Dycal was better adapted to the cavity floor than Prisma VLC Dycal. Disorganization of the resin-bonded Prisma VLC Dycal was minimal even after acid etching the enamel, sectioning and ultrasonic debridement. Dycal appeared to be more friable, and occasionally exhibited marked disorganization as a result of these procedures.

  17. Clinical outcome of direct pulp capping with MTA or calcium hydroxide: a systematic review and meta-analysis.

    Science.gov (United States)

    Zhu, Chenxi; Ju, Bin; Ni, Rong

    2015-01-01

    Direct pulp capping is one of the most common dental practices in endodontic therapy. This systematic review and meta-analysis aim to determine whether the effect of mineral trioxide aggregate (MTA) and calcium hydroxide for direct pulp capping is different, as measured by the clinical and radiographic analysis. The study list was obtained by searching PubMed, Springer Link, Scopus and Cochrane Database. Only those papers that met the inclusion criteria were analyzed. The results indicated that four studies met the inclusion criteria. Statistically significant difference was found between the success rates of MTA and calcium hydroxide treated teeth that needed direct pulp capping (P=0.002). Clinical assessments of the MTA versus calcium hydroxide for direct pulp capping suggested that MTA was superior to calcium hydroxide in direct pulp capping resulting in a lower failure rate (risk difference 0.1 [95% CI 0.04 to 0.16]). In conclusion, MTA has a higher clinical success rate for direct pulp capping comparing to calcium hydroxide, and might be a suitable replacement for calcium hydroxide.

  18. Interlayer Structure of Bioactive Molecule, 2-Aminoethanesulfonate, Intercalated into Calcium-Containing Layered Double Hydroxides

    Directory of Open Access Journals (Sweden)

    Tae-Hyun Kim

    2012-01-01

    Full Text Available We have successfully intercalated 2-aminoethanesulfonate, a well-known biomolecule taurine, into calcium-containing layered double hydroxides via optimized solid phase intercalation. According to X-ray diffraction patterns and infrared spectroscopy, it was revealed that the intercalated taurine molecules were each directly coordinated to other calcium cation and arranged in a zig-zag pattern. Scanning electron microscopy showed that the particle size and morphology of the LDHs were not affected by the solid phase intercalation, and the surface of intercalates was covered by organic moieties. From ninhydrin amine detection tests, we confirmed that most of the taurine molecules were well stabilized between the calcium-containing LDH layers.

  19. Diode Laser and Calcium Hydroxide for Elimination of Enterococcus Faecalis in Root Canal

    Directory of Open Access Journals (Sweden)

    Neda Naghavi

    2014-06-01

    Full Text Available Introduction: The ultimate goal of endodontic treatment is to eliminate the bacterial infection in the root canal system. While mechanical debridement combined with chemical irrigation removes the bulk of microorganisms, residual bacteria are readily detectable in approximately one-half of teeth just prior to obturation. Laser light can be used to destroy bacteria. This in vitro study was performed to evaluate the effect of diode laser and calcium hydroxide on mono-infected dental canals.Methods: Fifty five single-rooted human premolars were prepared and contaminated with Enterococcus faecalis. After three weeks of incubation, the samples were divided into three experimental groups (n = 15 and two control groups (n = 5. In the first and second groups, the teeth were rinsed for 5 min with either sterile saline or 5.25% NaOCl and irradiated with a 810-nm diode laser at 1.5 W output for 5 × 4s. In the third group, the teeth were rinsed with 5.25% NaOCl and then Ca(OH2 paste was inserted in the canals for 1 week. Intracanal bacterial sampling was done and the samples were plated to determine the CFU count. Results: 5.25% NaOCl plus laser was as effective as calcium hydroxide and significantly more effective than sterile saline (P>0.05 in elimination of E. faecalis. Complete elimination of E. faecalis was seen only for the one week calcium hydroxide treatment. Conclusion: Combination therapy with NaOCl irrigation and diode laser irradiation can be recommended as an effective treatment option for elimination of E. faecalis from the root canal system.

  20. [Effects of the treatment of coffee pulp, fresh or ensilaged, with calcium hydroxide, on its nutritive value].

    Science.gov (United States)

    Gómez-Brenes, R; Bendaña, G; González, J M; Jarquín, R; Braham, J E; Bressani, R

    1988-03-01

    This study was carried out to determine the effects of the addition of calcium hydroxide on the chemical composition and nutritive value of fresh or ensilaged coffee pulp. Fresh or ensilaged pulp were mixed with 1, 2 and 3% of calcium hydroxide. The process was carried out during 0 and 16 hr, after which time the treated pulp was sun-dried for 36 hr until moisture content reached 12%. These samples were then analyzed for their proximate chemical composition and for some minerals (Ca, P, Na, K), as well as for caffeine, tannins and chlorogenic and caffeic acids content. Diets were then prepared from these materials, containing 15% protein and 15 or 30% fresh or ensilaged coffee pulp, and offered to weanling rats during six weeks. Information required on weight gain, food conversion, apparent digestibility and toxicity of the diets was recorded. Results of the chemical analysis revealed that the main changes found in both types of pulp as a result of the calcium hydroxide treatment were the following: a decrease in ether extract (from 4.0 to 2.5 g/100 g), crude fiber (from 18.3 to 11.9 g/100 g) and protein content (from 12.3 to 8.6 g/100 g) in an inverse relation to the amount of calcium hydroxide used. The amount of ash increased, fluctuated between 5.5 and 15.4%, depending on the amount of calcium hydroxide used. The latter affected the Ca:P ratio in the diets, where an average ratio of 7.2:1 was found in the control pulp (0% calcium hydroxide) and 59.0:1 in those treated with the highest amount of calcium hydroxide (3%). Regarding the caffeine, tannins and chlorogenic and caffeic acids contents, calcium hydroxide was effective in decreasing only tannins, more so in the fresh than in the ensilaged pulp; the decrease was in direct proportion to the amount of calcium hydroxide added and to the length of the Ca(OH)2 treatment. The results of the biological assays showed that the addition of Ca(OH)2 in either of the two time periods used and at either of the

  1. Improving the quality of rice straw by urea and calcium hydroxide on rumen ecology, microbial protein synthesis in beef cattle.

    Science.gov (United States)

    Polyorach, S; Wanapat, M

    2015-06-01

    Four rumen-fistulated beef cattle were randomly assigned to four treatments according to a 4 × 4 Latin square design to study the influence of urea and calcium hydroxide [Ca(OH)2 ] treatment of rice straw to improve the nutritive value of rice straw. Four dietary treatments were as follows: untreated rice straw, 50 g/kg urea-treated rice straw, 20 g/kg urea + 20 g/kg calcium hydroxide-treated rice straw and 30 g/kg urea + 20 g/kg calcium hydroxide-treated rice straw. All animals were kept in individual pens and fed with concentrate at 0.5 g/kg of BW (DM), rice straw was fed ad libitum. The experiment was conducted for four periods, and each period lasted for 21 days. During the first 14 days, DM feed intake measurements were made while during the last 7 days, all cattle were moved to metabolism crates for total faeces and urine collections. The results revealed that 20 g/kg urea + 20 g/kg calcium hydroxide-treated rice straw improved the nutritive value of rice straw, in terms of dry matter intake, digestibility, ruminal volatile fatty acids, population of bacteria and fungi, nitrogen retention and microbial protein synthesis. Based on this study, it could be concluded that using urea plus calcium hydroxide was one alternative method to improve the nutritive value of rice straw, rumen ecology and fermentation and thus a reduction of treatment cost.

  2. Radiopacity evaluation of root canal sealers containing calcium hydroxide and MTA

    Directory of Open Access Journals (Sweden)

    Juliane Maria Guerreiro- Tanomaru

    2009-06-01

    Full Text Available The purpose of this study was to evaluate the radiopacity of root canal sealers containing calcium hydroxide and MTA (Acroseal, Sealer 26, Sealapex, Endo CPM Sealer, Epiphany and Intrafill. Five disc-shaped specimens (10 x 1 mm were fabricated from each material, according to the ISO 6876/2001 standard. After setting of the materials, radiographs were taken using occlusal film and a graduated aluminum stepwedge varying from 2 to 16 mm in thickness. The dental X-ray unit (GE1000 was set at 50 kVp, 10 mA, 18 pulses/s and distance of 33.5 cm. The radiographs were digitized and the radiopacity compared to that of the aluminum stepwedge using VIXWIN-2000 software (Gendex. The data (mmAl were analyzed statistically by ANOVA and Tukey's test at the 5% significance level. Epiphany and Intrafill presented the highest radiopacity values (8.3 mmAl and 7.5 mmAl respectively, p < 0.05 followed by Sealer 26 (6.3 mmAl, Sealapex (6.1 mmAl and Endo CPM Sealer (6 mmAl. Acroseal was the least radiopaque material (4 mmAl, p < 0.05. In conclusion, the calcium hydroxide- and MTA-containing root canal sealers had different radiopacities. However, all materials presented radiopacity values above the minimum recommended by the ISO standard.

  3. Diffusion of hydroxyl ions from calcium hydroxide and Aloe vera pastes.

    Science.gov (United States)

    Batista, Victor Eduardo de Souza; Olian, Douglas Dáquila; Mori, Graziela Garrido

    2014-01-01

    This study evaluated the diffusion through the dentinal tubules of hydroxyl ions from different calcium hydroxide (CH) pastes containing Aloe vera. Sixty single-rooted bovine teeth were used. The tooth crowns were removed, the root canals were instrumented and the specimens were assigned to 4 groups (n=15) according to the intracanal medication: Group CH/S - CH powder and saline paste; Group CH/P - CH powder and propylene glycol paste; Group CH/A - calcium hydroxide powder and Aloe vera gel paste; Group CH/A/P - CH powder, Aloe vera powder and propylene glycol paste. After placement of the root canal dressings, the teeth were sealed coronally and apically with a two-step epoxy adhesive. The teeth were placed in identified flasks containing deionized water and stored in an oven with 100% humidity at 37 °C. After 3 h, 24 h, 72 h, 7 days, 15 days and 30 days, the deionized water in the flasks was collected and its pH was measured by a pH meter. The obtained data were subjected to statistical analysis at a significance level of 5%. The results demonstrated that all pastes provided diffusion of hydroxyl ions through the dentinal tubules. The combination of Aloe vera and CH (group CH/A) provided a constant release of calcium ions. Group CH/A/P showed the highest pH at 24 and 72 h. In conclusion, the experimental pastes containing Aloe vera were able to enable the diffusion of hydroxyl ions through the dentinal tubules.

  4. Removal of oxyanions from synthetic wastewater via carbonation process of calcium hydroxide: applied and fundamental aspects.

    Science.gov (United States)

    Montes-Hernandez, G; Concha-Lozano, N; Renard, F; Quirico, E

    2009-07-30

    Removal of oxyanions (selenite, selenate, arsenate, phosphate and nitrate) during calcite formation was experimentally studied using aqueous carbonation of calcium hydroxide under moderate pressure (P(CO2) congruent with 20 bar) and temperature (30 degrees C). The effects of Ca(OH)(2) dose (10 and 20 g), Ca(OH)(2) source (commercial pure material or alkaline paper mill waste) and oxyanion initial concentration (from 0 to 70 mg atom/L) were investigated for this anisobaric gas-liquid-solid system. The Ca(OH)(2) carbonation reaction allowed successfully the removal of selenite (>90%), arsenate (>78%) and phosphate (congruent with 100%) from synthetic solutions. Conversely, nitrate and selenate had not any physicochemical affinity/effect during calcite formation. The rate of CO(2) transfer during calcite formation in presence of oxyanions was equal or slower than for an oxyanion-free system, allowing to define a retarding kinetic factor RF that can vary between 0 (no retarding effect) to 1 (total inhibition). For selenite and phosphate RF was quite high, close to 0.3. A small retarding effect was detected for arsenate (RF approximately 0.05) and no retarding effect was detected for selenate and nitrate (RF approximately 0). In general, RF depends on the oxyanion initial concentration, oxyanion nature and Ca(OH)(2) dose. The presence of oxyanions could also influence the crystal morphology and aggregation/agglomeration process. For example, a c-axis elongation of calcite crystals was clearly observed at the equilibrium, for calcite formation in presence of selenite and phosphate. The oxyanions removal process proposed herein was inspired on the common physicochemical treatment of wastewater using calcium hydroxide (Ca(OH)(2)). The particularity, for this novel method is the simultaneous calcium hydroxide carbonation with compressed carbon dioxide in order to stabilise the solid matter. This economical and ecological method could allow the removal of various oxyanions

  5. Polymer Coated CaAl-Layered Double Hydroxide Nanomaterials for Potential Calcium Supplement

    Directory of Open Access Journals (Sweden)

    Tae-Hyun Kim

    2014-12-01

    Full Text Available We have successfully prepared layered double hydroxide (LDH nanomaterials containing calcium and aluminum ions in the framework (CaAl-LDH. The surface of CaAl-LDH was coated with enteric polymer, Eudragit®L 100 in order to protect nanomaterials from fast dissolution under gastric condition of pH 1.2. The X-ray diffraction patterns, Fourier transform infrared spectroscopy, scanning electron and transmission electron microscopy revealed that the pristine LDH was well prepared having hydrocalumite structure, and that the polymer effectively coated the surface of LDH without disturbing structure. From thermal analysis, it was determined that only a small amount (less than 1% of polymer was coated on the LDH surface. Metal dissolution from LDH nanomaterials was significantly reduced upon Eudragit®L 100 coating at pH 1.2, 6.8 and 7.4, which simulates gastric, enteric and plasma conditions, respectively, and the dissolution effect was the most suppressed at pH 1.2. The LDH nanomaterials did not exhibit any significant cytotoxicity up to 1000 μg/mL and intracellular calcium concentration significantly increased in LDH-treated human intestinal cells. Pharmacokinetic study demonstrated absorption efficiency of Eudragit®L 100 coated LDH following oral administration to rats. Moreover, the LDH nanomaterials did not cause acute toxic effect in vivo. All the results suggest the great potential of CaAl-LDH nanomaterials as a calcium supplement.

  6. Hydrothermal and mechanochemical reactions of rice husk ash with calcium hydroxide

    Energy Technology Data Exchange (ETDEWEB)

    Sugita, S.; Isojima, Y. [Hachinohe Institute of Technology, Aomori (Japan); Yu, Q. [Wuhan University of Technology, (Taiwan, Province of China)

    1998-05-01

    It is well known that a calcium silicate hydrate, commonly referred to as C-S-H gel, is important for cement to exhibit strength. Silica is present in rice husk ash to around 90%. When sufficiently sintered and crushed, rice husk ash mostly comprises amorphous silica having a large surface area. It is reactive, and is considered to contribute to improvement of concrete strength and durability. In this study, rice husk ash is reacted with calcium hydroxide under hydrothermal conditions or mechanochemical conditions at normal temperature, to synthesize Ca(1.5)SiO(3.5){center_dot}xH2O as one of the calcium silicate hydrates. It has an average particle size of 10{mu}m or smaller, which varies depending on synthesis method and condition. The compound synthesized at 40degC is composed of flocs having a porous structure and large specific surface area, as is the case with a C-S-H gel present in Portland cement paste. It loses the above structure and moisture in the fine pores gradually, when heated, but remains amorphous at up to 750degC. It is transformed into wollastonite, when heated to 780degC. 7 refs., 8 figs., 3 tabs.

  7. Polymer coated CaAl-layered double hydroxide nanomaterials for potential calcium supplement.

    Science.gov (United States)

    Kim, Tae-Hyun; Lee, Jeong-A; Choi, Soo-Jin; Oh, Jae-Min

    2014-12-05

    We have successfully prepared layered double hydroxide (LDH) nanomaterials containing calcium and aluminum ions in the framework (CaAl-LDH). The surface of CaAl-LDH was coated with enteric polymer, Eudragit®L 100 in order to protect nanomaterials from fast dissolution under gastric condition of pH 1.2. The X-ray diffraction patterns, Fourier transform infrared spectroscopy, scanning electron and transmission electron microscopy revealed that the pristine LDH was well prepared having hydrocalumite structure, and that the polymer effectively coated the surface of LDH without disturbing structure. From thermal analysis, it was determined that only a small amount (less than 1%) of polymer was coated on the LDH surface. Metal dissolution from LDH nanomaterials was significantly reduced upon Eudragit®L 100 coating at pH 1.2, 6.8 and 7.4, which simulates gastric, enteric and plasma conditions, respectively, and the dissolution effect was the most suppressed at pH 1.2. The LDH nanomaterials did not exhibit any significant cytotoxicity up to 1000 μg/mL and intracellular calcium concentration significantly increased in LDH-treated human intestinal cells. Pharmacokinetic study demonstrated absorption efficiency of Eudragit®L 100 coated LDH following oral administration to rats. Moreover, the LDH nanomaterials did not cause acute toxic effect in vivo. All the results suggest the great potential of CaAl-LDH nanomaterials as a calcium supplement.

  8. Oily calcium hydroxide suspension (Osteoinductal) used as an adjunct to guided bone regeneration: an experimental study in rats.

    NARCIS (Netherlands)

    Stavropoulos, A.; Geenen, C.; Nyengaard, J.R.; Karring, T.; Sculean, A.

    2007-01-01

    OBJECTIVES: To evaluate whether an oily calcium hydroxide suspension (OCHS) promotes bone healing when used as an adjunct to guided bone regeneration (GBR). MATERIAL AND METHODS: Rigid, hemispherical, teflon capsules were placed with their open part facing the lateral surface of the ramus on both si

  9. Transportation of apical root canal after removal of calcium hydroxide when used as an intracanal medicament: An in vitro evaluation

    Directory of Open Access Journals (Sweden)

    Nurul-Ameen Inamdar

    2013-01-01

    Full Text Available Aim: To evaluate the incidence of apical root canal transportation after the removal of calcium hydroxide in straight and curved canals. Materials and Methods: Twenty maxillary central incisors (Group A and twenty mandibular molars (Group B, mesiobuccal canal were instrumented to the working length using #15 to #45 K-file and # 15 to #30 K-file, respectively. Post instrumentation digital images were taken with the corresponding final file inserted into the canal to the working length. The root canals were then filled with Calcium hydroxide paste using Lentulo spirals and the teeth incubated at 37°C for seven days. The calcium hydroxide paste was then removed up to the working length using a #45 file for group A and a pre curved #30 file for group B. Final digital images were taken with the file inserted into the canal to the working length. Post instrumentation and final digital images were superimposed to evaluate the incidence of transportation. Result: In Group A, no transportation was detected, whereas in Group B, 8 out of 20 canals showed apical transportation. Statistically significant differences were observed between Groups A and B ( P <0.05. Conclusion: Care should be taken when removing the calcium hydroxide paste from curved root canals to avoid transportation.

  10. Human pulp response after partial pulpotomy with two calcium hydroxide products.

    Science.gov (United States)

    Sübay, R K; Suzuki, S; Suzuki, S; Kaya, H; Cox, C F

    1995-09-01

    Twenty human permanent teeth were used to study the pulpal response of two calcium hydroxide products, Dycal and Pulpdent Multi-Cal, after partial pulpotomy. Teeth were extracted at 4 months, fixed, and prepared for histologic examination. All 10 teeth treated with Dycal showed complete soft tissue healing and bridge formation. No stained bacteria were seen throughout the serial sections. One tooth treated with Dycal showed acceptable histologic results, dentin deposition in the root canal. Six cases dressed with Pulpdent Multi-Cal showed acceptable histologic results, whereas four teeth showed severe inflammation or necrosis associated with bacterial penetration into the pulp tissue. Clinically, one tooth treated with Pulpdent Multi-Cal showed pulpal pain and was extracted at 90 days. Our data support the thesis that human permanent pulps will promote tissue healing and dentin bridge formation as long as bacterial microleakage is excluded.

  11. The effect of calcium hydroxide treatment on the nutritive and feeding value of Albizia procera for growing goats

    Energy Technology Data Exchange (ETDEWEB)

    Alam, M.R. [Department of Animal Science, Bangladesh Agricultural University, Mymensingh (Bangladesh)]. E-mail: mralam@royalten.net.bd; Kabir, A.K.M.A.; Amin, M.R. [Department of Animal Science, Bangladesh Agricultural University, Mymensingh (Bangladesh); McNeill, D.M. [Faculty of Veterinary Science, University of Sydney, Camden, NSW (Australia)

    2005-08-19

    Albizia procera (Albizia) is widely planted in Bangladesh for timber and the leaves are also used as forage. In the dry season the leaves are less palatable than in the wet season and this may be a consequence of an excessive content of tannin. Albizia foliage was collected in the wet (June) and dry (January) seasons from six agro-ecological zones across Bangladesh and chemical composition, for tannins in particular, was determined. Variation in the tannin content across the six zones proved to be minimal. However, the concentration of tannins was almost two-fold higher in the dry compared to the wet season. To assess the potential for deactivating the tannins in Albizia so as to improve its nutritive value, leaves were treated with alkali (either calcium hydroxide or potassium carbonate) or polyethylene glycol (PEG). Alkali treatment reduced the concentrations of extractable tannin by as much as 92%. The ability of calcium hydroxide to deactivate tannin was then tested in vivo. Young goats, fed a basal diet of hay and wheat bran, were allocated to 4 equal groups (n = 4 per group) and supplemented with fresh Albizia foliage (at 300 g/kg of the diet) that was either untreated, or treated with either PEG, calcium hydroxide or calcium hydroxide + PEG. The supplements were fed daily for 9 weeks to allow the effects of chemical treatment on intake and growth rate to be defined. In vivo digestibility, nitrogen (N) balance, and microbial N supply were measured over the 5th week. Intakes of feed dry matter (DM) and the digestibility of DM were similar across treatments (mean intake 32 g/(kg LW day), mean DM digestibility 0.63). However, both the PEG and the PEG + calcium hydroxide treatments, compared to the control and calcium hydroxide only treatments, increased N digestibility (0.72, 0.70 versus 0.60, 0.61), N retention (0.43, 0.48 mg N/mg versus 0.26, 0.27 mg N/mg N intake), and microbial N supply (23.7, 21.4 g/day versus 14.2, 12.4 g/day). These increases translated

  12. Kinetics and Mechanism of Calcium Hydroxide Conversion into Calcium Alkoxides: Implications in Heritage Conservation Using Nanolimes.

    Science.gov (United States)

    Rodriguez-Navarro, Carlos; Vettori, Irene; Ruiz-Agudo, Encarnacion

    2016-05-24

    Nanolimes are alcohol dispersions of Ca(OH)2 nanoparticles used in the conservation of cultural heritage. Although it was believed that Ca(OH)2 particles were inert when dispersed in short-chain alcohols, it has been recently shown that they can undergo transformation into calcium alkoxides. Little is known, however, about the mechanism and kinetics of such a phase transformation as well as its effect on the performance of nanolimes. Here we show that Ca(OH)2 particles formed after lime slaking react with ethanol and isopropanol and partially transform (fractional conversion, α up to 0.08) into calcium ethoxide and isopropoxide, respectively. The transformation shows Arrhenius behavior, with apparent activation energy Ea of 29 ± 4 and 37 ± 6 kJ mol(-1) for Ca-ethoxide and Ca-isopropoxide conversion, respectively. High resolution transmission electron microscopy analyses of reactant and product phases show that the alkoxides replace the crystalline structure of Ca(OH)2 along specific [hkl] directions, preserving the external hexagonal (platelike) morphology of the parent phase. Textural and kinetic results reveal that this pseudomorphic replacement involves a 3D diffusion-controlled deceleratory advancement of the reaction front. The results are consistent with an interface-coupled dissolution-precipitation replacement mechanism. Analysis of the carbonation of Ca(OH)2 particles with different degree of conversion into Ca-ethoxide (α up to 0.08) and Ca-isopropoxide (α up to 0.04) exposed to air (20 °C, 80% relative humidity) reveals that Ca-alkoxides significantly reduce the rate of transformation into cementing CaCO3 and induce the formation of metastable vaterite, as opposed to stable calcite which forms in untransformed Ca(OH)2 samples. Similar effects are obtained when a commercial nanolime partially transformed into Ca-ethoxide is subjected to carbonation. Such effects may hamper/delay the strengthening or consolidation effects of nanolimes, thus having

  13. Possible mechanisms of lack of dentin bridge formation in response to calcium hydroxide in primary teeth

    Directory of Open Access Journals (Sweden)

    G R Ravi

    2015-01-01

    Full Text Available Introduction: The usage of Calcium hydroxide (CaOH2 has wide applications due to the property of osteo-inductive, protective, and antibacterial actions. However, it is not used in primary teeth, as it fails to form reparative dentin and the exact mechanism has not been explained. The hypothesis: The authors propose an explanation that lack of dentin bridge formation in response to (CaOH2 in primary teeth could be multifactorial: inability of the deciduous stem cells to generate complete dentin-pulp-like tissue; the absence of calcium-magnesium-dependent adenosine triphosphatase (Ca-Mg ATPase in the odontoblasts; the pre-existing predilection of deciduous dentine pulp to form odontoclasts; the solubility of (CaOH2. Evaluation of the hypothesis: The hypothesis discusses the innate traits of the deciduous stem cells that lack the ability to form the dentin bridge, the absence of Ca-Mg ATPase enzyme and increased solubility of (CaOH2 together fail to stimulate the odontoblasts. Alternatively, pre-existing progenitor cells with proclivity to change into odontoclasts may cause internal resorption and hamper formation of reparative dentin.

  14. Critical Appraisal. Comparative Performance of Mineral Trioxide Aggregate Versus Calcium Hydroxide as a Direct Pulp Capping Agent.

    Science.gov (United States)

    Jefferies, Steven R

    2016-01-01

    Vital pulp therapy is the general concept involved in the "regenerative" restorative treatment of the reversibly injured dental pulp with the intention of maintaining its vitality in a restored, functioning tooth. While this procedure has been attempted with various materials and techniques over a period of several centuries, the advent of hard-setting calcium hydroxide materials in the late 1950s made the procedure of direct pulp capping a more routine and relatively predictable procedure. More recently, in the mid 1990s, a new type of water-based, "hydraulic-type," calcium silicate-based cement, mineral trioxide aggregate (MTA), was introduced to dentistry as a possible alternative to the established standard of hard-setting calcium hydroxide. Over the last two decades, a slowly growing body of pre-clinical and human clinical studies evaluating and comparing these two materials has developed. Most recently, a number of well-designed, randomized controlled studies and resultant systematic reviews have been completed and published regarding the comparative efficacy of calcium hydroxide versus MTA for direct pulp capping. This Critical Appraisal considers and reviews some of the more recently published reports which provide a more definitive answer to this clinical research question.

  15. Assessment of the Pozzolanic Activity of a Spent Catalyst by Conductivity Measurement of Aqueous Suspensions with Calcium Hydroxide

    Directory of Open Access Journals (Sweden)

    Sergio Velázquez

    2014-03-01

    Full Text Available The pozzolanic activity of the spent catalyst produced by fluid catalytic cracking (FCC has been studied by various methods in recent years. However, no quick and easy method has been reported for this activity based on the associated studies. In this work, the pozzolanic activity of a spent catalyst was investigated by measuring its electrical conductivity in aqueous suspensions of pozzolan/calcium hydroxide. The behavior of the FCC catalyst residue was compared to that of reactive and inert materials of similar chemical compositions. Further, the influence of temperature on the suspension was studied, and also, a new method was proposed in which the pozzolan/calcium hydroxide ratio was varied (with the initial presence of solid Ca(OH2 in the system. It was concluded that the method is effective, fast and simple for evaluating the high reactivity of the catalyst. Therefore, this method is an alternative for the evaluation of the reactivity of pozzolanic materials.

  16. Novel microcalorimetric assay for antibacterial activity of implant coatings: The cases of silver-doped hydroxyapatite and calcium hydroxide.

    Science.gov (United States)

    Braissant, Olivier; Chavanne, Philippe; de Wild, Michael; Pieles, Uwe; Stevanovic, Sabrina; Schumacher, Ralf; Straumann, Lukas; Wirz, Dieter; Gruner, Philipp; Bachmann, Alexander; Bonkat, Gernot

    2015-08-01

    Biomaterials with antimicrobial properties are now commonly used in different clinical specialties including orthopedics, endodontic, and traumatology. As a result, assessing the antimicrobial effect of coatings applied on implants is of critical importance. In this study, we demonstrate that isothermal microcalorimetry (IMC) can be used for monitoring bacterial growth and biofilm formation at the surface of such coatings and for determining their antimicrobial effects. The antibacterial effects of silver doped hydroxyapatite (HA) and calcium hydroxide coatings on Staphylococcus epidermidis were determined with a minimal workload. Using the Gompertz growth model we determined biofilm growth rates close to those values reported in the literature. Furthermore, we were able to estimate the reduction in the bacterial inocula originally applied at the surface of the coatings. Therefore, in addition to monitoring the antimicrobial effect of silver doped HA and calcium hydroxide coatings, we also demonstrate that IMC might be a valuable tool for assessing such antimicrobial properties of implant coatings at a minimal workload.

  17. Dual nutraceutical nanohybrids of folic acid and calcium containing layered double hydroxides

    Science.gov (United States)

    Kim, Tae-Hyun; Oh, Jae-Min

    2016-01-01

    Dual nutraceutical nanohybrids consisting of organic nutrient, folic acid (FA), and mineral nutrient, calcium, were prepared based on layered double hydroxide (LDH) structure. Among various hybridization methods such as coprecipitation, ion exchange, solid phase reaction and exfoliation-reassembly, it was found that exfoliation-reassembly was the most effective in terms of intercalation of FA moiety between Ca-containing LDH layers. X-ray diffraction patterns and infrared spectra indicated that FA molecules were well stabilized in the interlayer space of LDHs through electrostatic interaction. From the atomic force and scanning electron microscopic studies, particle thickness of LDH was determined to be varied with tens, a few and again tens of nanometers in pristine, exfoliated and reassembled state, respectively, while preserving particle diameter. The result confirmed layer-by-layer hybrid structure of FA and LDHs was obtained by exfoliation-reassembly. Solid UV-vis spectra showed 2-dimensional molecular arrangement of FA moiety in hybrid, exhibiting slight red shift in n→π* and π→π* transition. The chemical formulae of FA intercalated Ca-containing LDH were determined to Ca1.30Al(OH)4.6FA0.74·3.33H2O and Ca1.53Fe(OH)5.06FA2.24·9.94H2O by inductively coupled plasma-atomic emission spectroscopy, high performance liquid chromatography and thermogravimetry, showing high nutraceutical content of FA and Ca.

  18. Biocompatibility of a calcium hydroxide-propolis experimental paste in rat subcutaneous tissue.

    Science.gov (United States)

    Mori, Graziela Garrido; Rodrigues, Sindineia da Silva; Shibayama, Sheila Tieko; Pomini, Marcelo; do Amaral, Cristhiane Olivia Ferreira

    2014-01-01

    Intracanal medications are fundamental for disinfection of the root canal system and participate in periapical repair, so their biocompatibility is of utmost importance to avoid tissue damage. This study evaluated the biocompatibility of a experimental paste of calcium hydroxide and propolis in the subcutaneous tissue of rats. The study was conducted on 15 male Wistar rats. Two incisions were made on the dorsal region of each animal for introduction of 4 tubes: one tube was empty; one contained zinc oxide-eugenol cement, and the two other tubes were filled with experimental paste. After 7, 14 and 30 days, the animals were euthanized and the specimens were subjected to histotechnical preparation. The hematoxylin and eosin-stained histological sections were analyzed by light microscopy. Scores were established according to the inflammatory process and statistically compared by the Tukey test (α = 5%). The analysis of histological sections showed non-significant or mild inflammatory reaction in the connective tissue in contact with the empty tubes in all study periods while the contact of subcutaneous tissue with zinc oxide-eugenol elicited moderate or severe inflammation similarly without significant difference among the study periods. The connective tissue was moderately inflamed at 7 days when contacting the experimental paste, but the inflammatory process was non-significant or mild at 14 and 30 days. The experimental paste was biocompatible with the tissues after 14 days of subcutaneous implantation.

  19. Subcutaneous tissue reaction to castor oil bean and calcium hydroxide in rats

    Directory of Open Access Journals (Sweden)

    Samira Esteves Afonso Camargo

    2010-06-01

    Full Text Available Castor oil bean cement (COB is a new material that has been used as an endodontic sealer, and is a candidate material for direct pulp capping. OBJECTIVE: The purpose of this study was to evaluate the biocompatibility of a new formulation of COB compared to calcium hydroxide cement (CH and a control group without any material, in the subcutaneous tissue of rats. MATERIAL AND METHODS: The materials were prepared, packed into polyethylene tubes, and implanted in the rat dorsal subcutaneous tissue. Animals were sacrificed at the 7th and 50th days after implantation. A quantitative analysis of inflammatory cells was performed and data were subjected to ANOVA and Tukey's tests at 5% significance level. RESULTS: Comparing the mean number of inflammatory cells between the two experimental groups (COB and CH and the control group, statistically significant difference (p=0.0001 was observed at 7 and 50 days. There were no significant differences (p=0.111 between tissue reaction to CH (382 inflammatory cells and COB (330 inflammatory cells after 7 days. After 50 days, significantly more inflammatory cells (p=0.02 were observed in the CH group (404 inflammatory cells than in the COB group (177 inflammatory cells. CONCLUSIONS: These results demonstrate that the COB cement induces less inflammatory response within long periods.

  20. Review suggests direct pulp capping with MTA more effective than calcium hydroxide.

    Science.gov (United States)

    Rasaratnam, Lakshmi

    2016-09-01

    Data sourcesPubMed, the Cochrane Library, Embase, and the Web of Knowledge.Study selectionRandomised controlled trials (RCTs) or retrospective non-randomised trials (RNTs) of direct pulp capping in patients comparing mineral trioxide aggregate (MTA) with calcium hydroxide (CH) were considered.Data extraction and synthesisTwo reviewers independently abstracted data. Risk of bias for the RCTs was assessed using the Cochrane risk of bias tool and RNTs were assessed according to the methodological index for non-randomised studies. Different study designs were analysed separately.ResultsThirteen studies were included, ten of which were RCTs. Meta-analysis demonstrated a significantly higher success rate for MTA compared with the CH-capped groups. For RCT studies (2 studies, 405 teeth): OR = 2.26; (95% CI, 1.33-3.85; P = .003) and for RNTs (3 studies - 526 teeth): OR = 2.88; (95% CI, 1.86-4.44; P MTA showing significantly less inflammation compared with CH samples (OR = 4.56; 95% CI, 2.65 7.83; P MTA than CH-capped groups (OR = 3.56; 95% CI, 1.89 6.70; P MTA appears to be a suitable replacement of CH used for direct pulp capping.

  1. Clinical evaluation of glutaraldehyde with calcium hydroxide and glutaraldehyde with zinc oxide eugenol in pulpotomy of primary molars.

    Science.gov (United States)

    Shumayrikh, N M; Adenubi, J O

    1999-12-01

    The objectives of this study were to clinically evaluate the effectiveness of 2% buffered glutaraldehyde in pulpotomies of human primary molars and to compare the success rate of glutaraldehyde with calcium hydroxide and glutaraldehyde with zinc oxide eugenol as dressing material on the radicular pulp. Pulpotomies were completed on 61 primary molars in 19 children. The teeth were divided into two groups by random allocation. One group had a dressing of zinc oxide-eugenol base (IRM) incorporated with one drop of 2% buffered glutaraldehyde while the other group had a dressing of calcium hydroxide base incorporated with one drop of 2% buffered glutaraldehyde after the initial placement of 2% buffered glutaraldehyde on cotton pellet for 3 min. All teeth had light-curing compomer (Dyract) placed over the dressing material followed by a stainless steel crown restoration within 1 or 2 weeks after the pulpotomy. Blind clinical and radiographic evaluations of 57 teeth available after 12 months showed a success rate of 92.9% and 73.6% respectively. The clinical and radiographic success rates for glutaraldehyde/zinc oxide eugenol pulpotomies were 96.5% and 75.8% respectively while those for glutaraldehyde-calcium hydroxide were 89.2% and 71.4%. There was no statistically significant difference between the two groups either clinically or radiographically. The overall clinical success rate suggested that 2% buffered glutaraldehyde was an effective agent in the pulpotomy of human primary molars.

  2. Apexification of an Immature Permanent Incisor with the Use of Calcium Hydroxide: 16-Year Follow-Up of a Case

    Directory of Open Access Journals (Sweden)

    Camila Maggi Maia Silveira

    2015-01-01

    Full Text Available Apexification is a process of forming a mineralized apical barrier and had been performed by using calcium hydroxide paste, due to its biological and healing performances in cases of existent trauma. This clinical report aims to report the results of a 16-year follow-up study of an apexification treatment applied to nonvital tooth 22 of a healthy 8-year-old male after a trauma. Clinical inspection of the tooth showed fractures of the incisal edge and mesial angle, absence of coronal mobility, and negative pulp vitality under cold testing. Radiographic analysis of the root revealed incomplete apex formation. The possibility of fracture into the root or luxation injury was rejected, and the diagnosis of pulp necrosis was verified. Apexification by calcium hydroxide and subsequent endodontic treatment were planned. Initial formation of the mineralized apical barrier was observed after 3 months, and the barrier was considered to be completed after 8 months. Clinical, radiographic, and CBCT examinations after 16 years verified the success of the treatment, although the choice of calcium hydroxide for apexification treatment is discussed.

  3. The use of amalgam powder and calcium hydroxide to recreate a radiopaque image of a lost dental restoration.

    Science.gov (United States)

    Shiroma, Calvin Y

    2002-05-01

    Radiographs of dental restorations are highly reliable when used to identify postmortem dental remains. A problem exists if key dental restorations are missing or defective, which results in the loss of a comparative radiographic image. This article describes a simple method allowing the odontologist to quickly recreate a temporary radiopaque restoration. This article presents a method of using amalgam powder (radiopaque material) and calcium hydroxide (radiopaque material and transport medium for the amalgam powder) to recreate a radiopaque image on a tooth that has lost a dental restoration. Amalgam powder and calcium hydroxide is easily obtained (in any dental office), fairly clean, easy to manipulate, inexpensive, inert, stable, and able to be removed without damaging the dental remains. The amalgam powder/calcium hydroxide mixture can easily be re-shaped or modified to reflect the radiopaque image of the original restoration. Radiographic comparison of the "restored" dental remains to the antemortem radiographs is now possible. The use of this technique is presented in a case report.

  4. Accidental injury of the inferior alveolar nerve due to the extrusion of calcium hydroxide in endodontic treatment: a case report.

    Science.gov (United States)

    Shin, Yooseok; Roh, Byoung-Duck; Kim, Yemi; Kim, Taehyeon; Kim, Hyungjun

    2016-02-01

    During clinical endodontic treatment, we often find radiopaque filling material beyond the root apex. Accidental extrusion of calcium hydroxide could cause the injury of inferior alveolar nerve, such as paresthesia or continuous inflammatory response. This case report presents the extrusion of calcium hydroxide and treatment procedures including surgical intervention. A 48 yr old female patient experienced Calcipex II extrusion in to the inferior alveolar canal on left mandibular area during endodontic treatment. After completion of endodontic treatment on left mandibular first molar, surgical intervention was planned under general anesthesia. After cortical bone osteotomy and debridement, neuroma resection and neurorrhaphy was performed, and prognosis was observed. But no improvement in sensory nerve was seen following surgical intervention after 20 mon. A clinician should be aware of extrusion of intracanal medicaments and the possibility of damage on inferior alveolar canal. Injectable type of calcium hydroxide should be applied with care for preventing nerve injury. The alternative delivery method such as lentulo spiral was suggested on the posterior mandibular molar.

  5. Properties of Camphorated Paramonochlorophenol and Camphorated Paramonochlorophenol Associated to Calcium Hydroxide

    Directory of Open Access Journals (Sweden)

    Halim NAGEM FILHO

    2007-09-01

    Full Text Available Objective: To evaluate the biocompatibility of camphoratedparamonochlorophenol (CMCP at a proportion of 3.5:6.5 andcamphorate paramonochlorophenol associated to calcium hydroxide(CMCP+Ca(OH2 in rat subcutaneous tissue, and the antimicrobialpotential of these medications against some microorganisms.Method: Ten Wistar rats were anesthetized and received anintravenous injection of Evan’s blue dye followed by inoculation of0.1 mL of the tested drugs in the dorsal region. The amount ofreleased dye bound to plasma proteins was evaluated underspectrophotometry. The antimicrobial activity of the substancesagainst S. aureus, S. mutans, B. subtilis and C. albicans wasverified by measuring the zones of bacterial growth inhibition usingthe agar diffusion test.Results: The mean optical density values for CMCP andCMCP+Ca(OH2 were 0.325±0.025 (moderate reaction and0.211±0.040 (mild reaction, respectively. The measurements ofthe zones of bacterial growth inhibition were as follows: CMCP =7.29 mm and CMCP+Ca(OH2 = 7.29 mm for S. aureus; CMCP = 8.57mm and CMCP+Ca(OH2 = 7.0 mm for S. mutans; CMCP = 8.57 mmand CMCP+Ca(OH2 = 7.43 mm for B. subtilis; and CMCP - 8.71 mmand CMCP+Ca(OH2 - 8.29 mm para C. albicans.Conclusion: The obtained data indicated that CMCP was moreirritating than CMCP+Ca(OH2, while no statistically significantdifference was observed between the tested substances regardingtheir antimicrobial activity (ANOVA.

  6. Exopolysaccharide dispelled by calcium hydroxide with volatile vehicles related to bactericidal effect for root canal medication

    Directory of Open Access Journals (Sweden)

    Lei Lei

    Full Text Available ABSTRACT Objective: Enterococcus faecalis is the dominant microbial species responsible for persistent apical periodontitis with ability to deeply penetrate into the dentin. Exopolysaccharides (EPS contribute to the pathogenicity and antibiotic resistance of E. faecalis. Our aim was to investigate the antimicrobial activity of calcium hydroxide (CH, camphorated parachlorophenol (CMCP, and chlorhexidine (CHX against E. faecalis in dentinal tubules. Material and Methods: Decoronated single-canal human teeth and semicylindrical dentin blocks were incubated with E. faecalis for 3 weeks. Samples were randomly assigned to six medication groups for 1 week (n=10 per group: CH + 40% glycerin-water solution (1:1, wt/vol; CMCP; 2% CHX; CH + CMCP (1:1, wt/vol; CH + CMCP (2:3, wt/vol; and saline. Bacterial samples were collected and assayed for colony-forming units. After dentin blocks were split longitudinally, confocal laser scanning microscopy was used to assess the proportion of viable bacteria and EPS production in dentin. Results: CMCP exhibited the best antimicrobial activity, while CH was the least sensitive against E. faecalis (p0.05. CH combined with CMCP inhibited EPS synthesis by E. faecalis, which sensitized biofilms to antibacterial substances. Moreover, increasing concentrations of CMCP decreased EPS matrix formation, which effectively sensitized biofilms to disinfection agents. Conclusion: The EPS matrix dispelled by CH paste with CMCP may be related to its bactericidal effect; the visualization and analysis of EPS formation and microbial colonization in dentin may be a useful approach to verify medicaments for antimicrobial therapy.

  7. Dual nutraceutical nanohybrids of folic acid and calcium containing layered double hydroxides

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Tae-Hyun; Oh, Jae-Min, E-mail: jaemin.oh@yonsei.ac.kr

    2016-01-15

    Dual nutraceutical nanohybrids consisting of organic nutrient, folic acid (FA), and mineral nutrient, calcium, were prepared based on layered double hydroxide (LDH) structure. Among various hybridization methods such as coprecipitation, ion exchange, solid phase reaction and exfoliation-reassembly, it was found that exfoliation-reassembly was the most effective in terms of intercalation of FA moiety between Ca-containing LDH layers. X-ray diffraction patterns and infrared spectra indicated that FA molecules were well stabilized in the interlayer space of LDHs through electrostatic interaction. From the atomic force and scanning electron microscopic studies, particle thickness of LDH was determined to be varied with tens, a few and again tens of nanometers in pristine, exfoliated and reassembled state, respectively, while preserving particle diameter. The result confirmed layer-by-layer hybrid structure of FA and LDHs was obtained by exfoliation-reassembly. Solid UV–vis spectra showed 2-dimensional molecular arrangement of FA moiety in hybrid, exhibiting slight red shift in n→π* and π→π* transition. The chemical formulae of FA intercalated Ca-containing LDH were determined to Ca{sub 1.30}Al(OH){sub 4.6}FA{sub 0.74}·3.33H{sub 2}O and Ca{sub 1.53}Fe(OH){sub 5.06}FA{sub 2.24}·9.94H{sub 2}O by inductively coupled plasma-atomic emission spectroscopy, high performance liquid chromatography and thermogravimetry, showing high nutraceutical content of FA and Ca. - Highlights: • We successfully intercalated FA molecules into Ca-containing LDHs. • Exfoliation-reassembly was proven to be the most effective. • The interaction between LDH and FA were studied by FT-IR and UV–vis spectra. • Thermal stability of FA were enhanced by electrostatic interaction with LDH layers.

  8. Effect of Calcium Hydroxide, Chlorhexidine Digluconate and Camphorated Monochlorophenol on the Sealing Ability of Biodentine Apical Plug

    Science.gov (United States)

    Srivastava, Harshit; Prasad, Ashwini B; Raisingani, Deepak; Soni, Dileep

    2016-01-01

    Introduction Teeth with immature apex are managed by establishing an apical plug using various materials and techniques. However, the use of previously placed intracanal medicament may affect the sealing ability of permanent filling material used as an apical plug. Aim To evaluate the effect of removal of previously placed Calcium Hydroxide, Chlorhexidine Digluconate and Camphorated Monochlorophenol as an intracanal medicament on the sealing ability of the Biodentine as an apical plug. Materials and Methods A total of 72 recently extracted human permanent teeth with single root were selected and stored in saline at room temperature. The crown portion of each tooth was removed at the level of cemento enamel junction; 14mm root length was taken as standard length. All the roots were submerged in 20% sulphuric acid up to 3 mm from the apex, for four days for root resorption. One sample was cut longitudinally to look for root resorption under stereo microscope. The canal preparation was done; the roots were kept in moist gauze after instrumentation. A total of 71 roots were randomly divided into three groups. GROUP 1:Calcium hydroxide paste, GROUP 2: Chlorhexidine digluconate, GROUP 3: Camphorated Monochlorophenol (CMCP). The medicaments were removed with stainless steel hand files and 0.5% sodium hypochlorite irrigation. After removal of medicament Biodentine was placed in apical third of resorbed roots and the remaining portion of the canals was filled with gutta-percha. All the 71 roots were analysed with fluid filtration method for evaluating microleakage. Results Comparing all the three groups statistically there was no significant difference. The mean values were found more for group 1 followed by group 2 & 3. Conclusion All the groups showed microleakage. Calcium hydroxide showed the maximum microleakage followed by Chlorhexidine digluconate and least with CMCP. PMID:27504409

  9. Will mineral trioxide aggregate replace calcium hydroxide in treating pulpal and periodontal healing complications subsequent to dental trauma?

    DEFF Research Database (Denmark)

    Bakland, Leif K; Andreasen, Jens O

    2012-01-01

    Mineral trioxide aggregate (MTA) has over the last two decades begun to take the place of calcium hydroxide (CH) in the treatment of a variety of pulpal and periodontal healing complications following dental trauma. These conditions include teeth with: (i) exposed pulps, (ii) immature roots...... and pulp necrosis, (iii) root fractures and pulp necrosis located in the coronal part of the pulps, and (iv) external infection-related (inflammatory) root resorption. The main reasons for replacing CH with MTA in these situations have generally been the delayed effect when using CH to induce hard tissues...

  10. Nerve lesions following apical extrusion of non-setting calcium hydroxide: A systematic case review and report of two cases

    DEFF Research Database (Denmark)

    Olsen, Jesper Jared; Thorn, Jens Jørn; Korsgaard, Niels;

    2014-01-01

    We present two cases of apical extrusion of non-setting, calcium hydroxide paste which had been placed as an interappointment root canal dressing during routine endodontic treatment and which resulted in tissue necrosis of a large part of themandible, while. Surgical intervention consisted...... effects and the use of an injectable system had most often been related to apical extrusion. Consequently, great care should be taken when applying the paste into the canal system. 2013 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved....

  11. Ecological comparison of calcium hydroxide and sodium hydrogen carbonate as sorbents; Oekologischer Vergleich der Sorptionsmittel Calciumhydroxid und Natriumhydrogencarbonat

    Energy Technology Data Exchange (ETDEWEB)

    Pacher, Christian; Weber-Blaschke, Gabriele [Technische Univ. Muenchen, Freising (Germany). Lehrstuhl fuer Rohstoff- und Energietechnologie; Mocker, Mario [ATZ Entwicklungszentrum, Sulzbach-Rosenberg (Germany); Faulstich, Martin [Technische Univ. Muenchen, Straubing (Germany). Wissenschaftszentrum Straubing

    2009-07-01

    Lime products have long been used with success for flue gas purification in waste incineration plants, where they serve to eliminate acid gas pollutants such as sulphur dioxide, hydrogen chloride and hydrogen fluoride. This article presents excerpts of a study commissioned by the German lime industry association for the purpose of obtaining an unbiased well-founded comparison of the environmental impact of the two sorbents calcium hydroxide and sodium hydrogen carbonate. The following questions were addressed by the study: Which of the two flue gas additives provides greater environmental benefit under specified conditions? What parameters influence the outcome? How can the results be viewed in regard to different plant configurations?.

  12. Revascularization of an Immature Tooth with Apical Periodontitis Using Calcium Hydroxide: A 3-year Follow-up.

    Science.gov (United States)

    Silva, Mauro Henrique Chagas; Campos, Celso Neiva; Coelho, Marcelo Santos

    2015-01-01

    Root canal treatment of teeth presenting immature development is a great challenge for both the patient and the professional. The thinness of the root canal walls of immature teeth may lead to root fracture and thus the outcomes of such treatments are uncertain. Revascularization is based on root canal decontamination followed by the induction of blood migration from the periapical tissues and the development of new vascular tissue in the canal space. The principle of disinfection in regenerative endodontics is that it should be achieved with minimum root canal instrumentation; an intracanal medication is used to inhibit bacterial growth and appropriate sealing of the coronal portion is performed. The American Association of Endodontists (AAE) considerations for regenerative endodontics include calcium hydroxide as an alternative intracanal dressing. This material has also been claimed to diminish the possibility of dental staining during revascularization procedures. The relatively new treatment protocol has been widely reported in the last few years; however it should be performed only when other alternatives are not reasonable. This case report presents a 3-year follow-up of a case of revascularization of a maxillary central incisor using calcium hydroxide as a root canal disinfection dressing.

  13. Effect of ultrasonic streaming on intra-dentinal disinfection and penetration of calcium hydroxide paste in endodontic treatment

    Directory of Open Access Journals (Sweden)

    Marcela Paola Castro ARIAS

    Full Text Available ABSTRACT Objective The antimicrobial effect of ultrasonic agitation of calcium hydroxide (CH pastes in infected bovine dentin and their penetrability were evaluated using confocal laser scanning microscopy (CLSM and microbiological culture. Material and Methods Fifty-two bovine teeth were infected with Enterococcus faecalis using a new contamination protocol; then they received CH paste and were divided into groups with or without ultrasound. Ultrasonic agitation was conducted for 1 min with a plain point insert. After 15 d, the CLSM analyzed the viable and dead bacteria with Live and Dead assay. The dentinal wall debris was collected by burs, and the colony forming units (CFU/mL were counted. The penetrability of the paste inside dentinal tubules was tested using the B-rodamine dye. Results The calcium hydroxide paste showed better results with the use of ultrasonic agitation (p<0.05. Conclusion The ultrasonic agitation of CH paste increased its antimicrobial action and was responsible for intradentinal penetration with the fulfilment of the tubules.

  14. Effect of ultrasonic streaming on intra-dentinal disinfection and penetration of calcium hydroxide paste in endodontic treatment

    Science.gov (United States)

    ARIAS, Marcela Paola Castro; MALIZA, Amanda Garcia Alves; MIDENA, Raquel Zanin; GRAEFF, Márcia Sirlene Zardin; DUARTE, Marco Antonio Húngaro; de ANDRADE, Flaviana Bombarda

    2016-01-01

    ABSTRACT Objective The antimicrobial effect of ultrasonic agitation of calcium hydroxide (CH) pastes in infected bovine dentin and their penetrability were evaluated using confocal laser scanning microscopy (CLSM) and microbiological culture. Material and Methods Fifty-two bovine teeth were infected with Enterococcus faecalis using a new contamination protocol; then they received CH paste and were divided into groups with or without ultrasound. Ultrasonic agitation was conducted for 1 min with a plain point insert. After 15 d, the CLSM analyzed the viable and dead bacteria with Live and Dead assay. The dentinal wall debris was collected by burs, and the colony forming units (CFU/mL) were counted. The penetrability of the paste inside dentinal tubules was tested using the B-rodamine dye. Results The calcium hydroxide paste showed better results with the use of ultrasonic agitation (p<0.05). Conclusion The ultrasonic agitation of CH paste increased its antimicrobial action and was responsible for intradentinal penetration with the fulfilment of the tubules. PMID:28076462

  15. Comparing the reinforcing effects of a resin modified glassionomer cement, Flowable compomer, and Flowable composite in the restoration of calcium hydroxide-treated immature roots in vitro

    OpenAIRE

    S Prathibha Rani

    2011-01-01

    One hundred and sixty human permanent central incisors were enlarged to a 120 file size after crown removal procedure to simulate immature teeth. The root canals were filled with calcium hydroxide and stored for 15 days (phase I), 30 days (phase II), 90 days (phase III), and 180 days (Phase IV). At the end of these selected time periods, calcium hydroxide was cleaned off the root canals of forty teeth that were randomly selected and obturated with gutta-percha points in the apical 2 mm of the...

  16. Study on Producing Magnesium Hydroxide by Concentrated Seawater- calcium Method%浓海水-钙法制取氢氧化镁工艺研究

    Institute of Scientific and Technical Information of China (English)

    高春娟; 张雨山; 黄西平; 蔡荣华

    2011-01-01

    Calcium method ( light burned dolomite and lime) producing magnesium hydroxide from concentrated seawater of desalination plant has advantages of low producing cost and rich resources. However, magnesium hydroxide produced by traditional calcium method has high -content impurities and low purity. Based on patent technology developing independently, the technology of concentrated seawater - calcium method producing magnesium hydroxide was improved in raw material pretreatment, magnesium hydroxide synthesis, calcium sulfate precipitation and precipitate washing. The results showed that the quantities of magnesium hydroxide produced by new technology accord with industry standard, while the content of calcium oxide is reduced significantly. Meanwhile, high quantity byproduct calcium sulfate was obtained.%浓海水一钙法(轻烧白云石、石灰)制取氢氧化镁具有生产成本低、资源丰富的优势,但传统钙法生产的氢氧化镁存在杂质含量高、产品纯度低等缺陷.文章以自主研发的专利技术为基础,从原料预处理、氢氧化镁合成、硫酸钙沉降、沉淀洗涤等方面对浓海水-钙法制取氢氧化镁的工艺进行改进.结果表明,采用改进后的工艺制备的氢氧化镁质量符合行业标准要求,氧化钙含量明显降低,同时得到高质量的副产硫酸钙.

  17. The evaluation of removal of calcium hydroxide paste from an artificial standardized groove in the apical root canal using different irrigation methodologies

    NARCIS (Netherlands)

    van der Sluis, L. W. M.; Wu, M. K.; Wesselink, P. R.

    2007-01-01

    Aim: To evaluate the capacity to remove a calcium hydroxide (Ca(OH)(2)) paste from the root canal and to evaluate the efficacy of Ca(OH)(2) removal during passive ultrasonic irrigation using either sodium hypochlorite (NaOCl) or water as an irrigant. Methodology: Sixteen mandibular premolars were us

  18. Nerve lesions following apical extrusion of non-setting calcium hydroxide: a systematic case review and report of two cases.

    Science.gov (United States)

    Olsen, J J; Thorn, J J; Korsgaard, N; Pinholt, E M

    2014-09-01

    We present two cases of apical extrusion of non-setting, calcium hydroxide paste which had been placed as an interappointment root canal dressing during routine endodontic treatment resulting in tissue necrosis of a large part of the mandible. Surgical intervention consisted of resections in both instances. In relation to the cases presented, a systematic review of similar cases in the literature between 1980 and April 2013 was conducted which resulted in eight cases meeting the criteria outlined. As with the two presented cases, half of these eight cases showed serious adverse effects and the use of an injectable system had most often been related to apical extrusion. Consequently, great care should be taken when applying the paste into the canal system.

  19. Statistical Analyses of Optimum Partial Replacement of Cement by Fly Ash Based on Complete Consumption of Calcium Hydroxide

    Directory of Open Access Journals (Sweden)

    Ouypornprasert Winai

    2016-01-01

    Full Text Available The objectives of this technical paper were to propose the optimum partial replacement of cement by fly ash based on the complete consumption of calcium hydroxide from hydration reactions of cement and the long-term strength activity index based on equivalent calcium silicate hydrate as well as the propagation of uncertainty due to randomness inherent in main chemical compositions in cement and fly ash. Firstly the hydration- and pozzolanic reactions as well as stoichiometry were reviewed. Then the optimum partial replacement of cement by fly ash was formulated. After that the propagation of uncertainty due to main chemical compositions in cement and fly ash was discussed and the reliability analyses for applying the suitable replacement were reviewed. Finally an applicability of the concepts mentioned above based on statistical data of materials available was demonstrated. The results from analyses were consistent with the testing results by other researchers. The results of this study provided guidelines of suitable utilization of fly ash for partial replacement of cement. It was interesting to note that these concepts could be extended to optimize partial replacement of cement by other types of pozzolan which were described in the other papers of the authors.

  20. Scientific Opinion on the safety assessment of the active substances, sodium erythorbate, sodium carbonate, sodium bicarbonate, iron sulphate, activated carbon, cellulose, calcium hydroxide, calcium chloride and water, for use as active system in food contact materials

    OpenAIRE

    2014-01-01

    This scientific opinion of EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids deals with the safety assessment of the active substances sodium erythorbate, sodium carbonate, sodium bicarbonate, iron sulfate, activated carbon, cellulose, calcium hydroxide, calcium chloride and water, used in mixture which is packed into sachets for absorbing oxygen/carbon dioxide emitting from/into the headspace surrounding packed food. All substances of this formulation have been e...

  1. Effect of Combined Calcium Hydroxide and Accelerated Portland Cement on Bone Formation and Soft Tissue Healing in Dog Bone Lesions

    Directory of Open Access Journals (Sweden)

    Khorshidi H

    2015-09-01

    Full Text Available Statement of Problem: Recent literatures show that accelerated Portland cement (APC and calcium hydroxide Ca (OH2 may have the potential to promote the bone regeneration. However, certain clinical studies reveal consistency of Ca (OH2, as one of the practical drawbacks of the material when used alone. To overcome such inconvenience, the combination of the Ca (OH2 with a bone replacement material could offer a convenient solution. Objectives: To evaluate the soft tissue healing and bone regeneration in the periodontal intrabony osseous defects using accelerated Portland cement (APC in combination with calcium hydroxide Ca (OH2, as a filling material. Materials and Methods: Five healthy adult mongrel dogs aged 2-3 years old (approximately 20 kg in weight with intact dentition and healthy periodontium were selected for this study. Two one-wall defects in both mesial and distal aspects of the 3rd premolars of both sides of the mandible were created. Therefore, four defects were prepared in each dog. Three defects in each dog were randomly filled with one of the following materials: APC alone, APC mixed with Ca (OH2, and Ca (OH2 alone. The fourth defect was left empty (control. Upon clinical examination of the sutured sites, the amount of dehiscence from the adjacent tooth was measured after two and eight weeks, using a periodontal probe mesiodistally. For histometric analysis, the degree of new bone formation was estimated at the end of the eighth postoperative week, by a differential point-counting method. The percentage of the defect volume occupied by new osteoid or trabecular bone was recorded. Results: Measurement of wound dehiscence during the second week revealed that all five APCs had an exposure of 1-2 mm and at the end of the study all samples showed 3-4 mm exposure across the surface of the graft material, whereas the Ca (OH2, control, and APC + Ca (OH2 groups did not show any exposure at the end of the eighth week of the study. The most

  2. [Clinico-pathological studies on the effects of calcium hydroxide eugenol preparations to the human vital pulp tissues].

    Science.gov (United States)

    Minagawa, M

    1989-05-01

    The present paper reports results of a study to evaluate clinico-pathologically the effects of calcium hydroxide eugenol preparations on exposed pulp tissues in permanent human teeth. The experiments were performed on 80 vital human teeth from patients ranging in age from 12 to 54 years. The experimental teeth were arbitrarily divided into the following 4 groups. Group CRCS: 20 cases treated with CRCS (Hygienic, Akron, Ohio, USA). Group KEZ: 20 cases treated with Dentalis KEZ (Neo Dental Chemical Products, Tokyo, Japan). Group CE: 20 cases treated with calcium hydroxide eugenol (positive control) Group E: 20 cases treated with pure eugenol (negative control). After local anesthesia, the experimental teeth were isolated with rubber dums or cotton rolls. Following preparation of Black's simple class 1 cavities with a diamond instrument mounted high-speed air turbine, the pulp was intentionally exposed by means of a steel bur mounted electric engine. The cavity and exposed pulp surface were cleaned with saline and dried on absorbent material. Then the experimental materials (agents) were applied to exposed pulp surface. The cavity was lined with gutta-percha temporally stopping, and the remainder was filled with silver amalgam. The teeth were clinically observed at various intervals from immediately to 530 days after treatment and then extracted under local anesthesia and prepared for histopathological study. Decalcified sections were stained with hematoxylin and eosin. 1) CLINICAL OBSERVATIONS: During the observation period, symptoms occurred in the following: Group CRCS: 4 (20%) out of 20 cases. Group KEZ: 4 (20%) out of 20 cases. Group CE: 6 (30%) out of 20 cases. Group E: None of 20 cases No spontaneous pain was observed in these groups. 2) Clinical evaluations Group: CRCS: 16 cases (80%) were good, 3 cases (15%) were satisfactory, and 1 cases (5%) were failure. Group KEZ: 16 cases (80%) were good, 1 cases (5%) were satisfactory, and 3 cases (15%) were failure

  3. Effect of cetyl trimethyl ammonium bromide concentration on structure, morphology and carbon dioxide adsorption capacity of calcium hydroxide based sorbents

    Energy Technology Data Exchange (ETDEWEB)

    Hlaing, Nwe Ni, E-mail: nwenihlaing76@gmail.com [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Department of International Development Engineering, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo (Japan); Department of Physics, University of Yangon, 11041 Kamayut, Yangon (Myanmar); Vignesh, K., E-mail: vignesh134@gmail.com [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Anano Sphere Sdn Bhd, Lorong Industri 11, Kawasan Industri Bukit Panchor, 14300 Nibong Tebal, Penang (Malaysia); Sreekantan, Srimala, E-mail: srimala@usm.my [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Pung, Swee-Yong [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Hinode, Hirofumi; Kurniawan, Winarto [Department of International Development Engineering, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo (Japan); Othman, Radzali [Faculty of Manufacturing Engineering, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Malacca (Malaysia); Thant, Aye Aye [Department of Physics, University of Yangon, 11041 Kamayut, Yangon (Myanmar); Mohamed, Abdul Rahman [Low Carbon Economy (LCE) Research Group, School of Chemical Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Salim, Chris [Department of Environmental Engineering, Surya University, Tangerang 15810, Banten (Indonesia)

    2016-02-15

    Graphical abstract: Carbonation conversions of (a) CC, (b) CH-2, (c) CH-4, (d) CH-6, (e) CH-8 precursor adsorbents for 10 cycles. - Highlights: • Ca(OH){sub 2} precursor was synthesized using precipitation method. • The effect of CTAB concentration on the synthesis of Ca(OH){sub 2} was studied. • The sorbent synthesized using 0.8 M of CTAB showed good CO{sub 2} adsorption capacity. • The cyclic stability of Ca(OH){sub 2} was increased with increase of CTAB concentration. - Abstract: Calcium hydroxide (Ca(OH){sub 2}) has been proposed as an important material for industrial, architectural, and environmental applications. In this study, calcium acetate was used as a precursor and cetyl trimethyl ammonium bromide (CTAB) was used as a surfactant to synthesize Ca(OH){sub 2} based adsorbents for carbon dioxide (CO{sub 2}) capture. The effect of CTAB concentration (0.2–0.8 M) on the structure, morphology and CO{sub 2} adsorption performance of Ca(OH){sub 2} was studied in detail. The synthesized samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy (FESEM), BET surfaced area and thermogravimetry-differential thermal analysis (TG–DTA) techniques. The phase purity, crystallite size, Brunauer–Emmett–Teller (BET) surface area and CO{sub 2} adsorption performance of Ca(OH){sub 2} precursor adsorbents were significantly increased when the concentration of CTAB was increased. XRD results showed that pure Ca(OH){sub 2} phase was obtained at the CTAB concentration of 0.8 M. TGA results exhibited that 0.8 M of CTAB-assisted Ca(OH){sub 2} precursor adsorbent possessed a residual carbonation conversion of ∼56% after 10 cycles.

  4. Precursor preparation for Ca-Al layered double hydroxide to remove hexavalent chromium coexisting with calcium and magnesium chlorides

    Science.gov (United States)

    Zhong, Lihua; He, Xiaoman; Qu, Jun; Li, Xuewei; Lei, Zhiwu; Zhang, Qiwu; Liu, Xinzhong

    2017-01-01

    Al(OH)3 and Ca(OH)2 powders are co-ground to prepare a precursor which hydrates into a layered double hydroxide (LDH) phase by agitation in aqueous solution with target hexavalent chromium (Cr(VI)) at room temperature, to achieve an obvious improvement in removal efficiency of Cr(VI) through an easy incorporation into the structure. Although the prepared precursor transforms into LDH phases also when agitated in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. The adsorption isotherm and kinetic studies show that the phenomena occurring on the Al-Ca precursor fit a pseudo-second-order kinetics with a Langmuir adsorption capacity of 59.45 mg/g. Besides, characterizations of the prepared precursor and the samples after adsorption are also performed by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Transmission electron microscope (TEM) to understand the reason of the preferential incorporation of Cr(VI) to the coexisting chloride salts during the LDH phase formation.

  5. Effect of treating sugarcane bagasse with urea and calcium hydroxide on feed intake, digestibility, and rumen fermentation in beef cattle.

    Science.gov (United States)

    Gunun, Nirawan; Wanapat, Metha; Gunun, Pongsatorn; Cherdthong, Anusorn; Khejornsart, Pichad; Kang, Sungchhang

    2016-08-01

    Four beef cattle with initial body weight of 283 ± 14 kg were randomly allocated according to a 4 × 4 Latin square design to study on the effect of feeding sugarcane bagasse (SB) treated with urea and/or calcium hydroxide (Ca(OH)2) on feed intake, digestibility, and rumen fermentation. The treatments were as follows: rice straw (RS), untreated SB (SB), 4 % urea-treated SB (SBU), and 2 % urea + 2 % Ca(OH)2-treated SB (SBUC), respectively. The results revealed that cattle fed with SBU and SBUC had higher feed intake and apparent digestibility. Ammonia nitrogen and blood urea nitrogen were increased in cattle fed with SB as roughage source (P urea and/or Ca(OH)2 treatment, and feeding treated SB could increase feed intake, digestibility, and rumen fermentation. This study suggested that SB treated with 2 % urea + 2 % Ca(OH)2 could be used as an alternative roughage source for ruminant feeding.

  6. Genotoxicity test of propolis extract, mineral trioksida aggregat, and calcium hydroxide on fibroblast BHK-21 cell cultures

    Directory of Open Access Journals (Sweden)

    Ceples Dian Kartika W.P

    2015-03-01

    Full Text Available Background: Health industry has always used natural products as an alternative. Propolis, a natural antibiotic, is a resinous yellow brown or dark brown substance derived from honey bees (Apis mellifera. The main chemical compounds contained in propolis are flavonoids, phenolics and other various aromatic compounds. Flavonoids are well known plant compounds that have antibacterial, antifungal, antiviral, antioxidant and anti-inflammatory proprieties. Propolis is expected to be an alternative used for root canal treatment with lower toxicity compared to calcium hydroxide (Ca(OH2 . Over the last decade, a new material, mineral trioxide aggregate (MTA was developed, and has been used as the gold standard. All materials used in mouth should be biocompatible. The initial level of material biocompatibility evaluation involves toxicity and genotoxicity tests. Purpose: This research is aimed to conduct comparison test of genotoxicity effect of propolis extract, MTA and Ca(OH2 on fibroblast BHK-21 cell culture. Methods: This research was conducted with single-cell gel electrophoresis method. Results: The results indicate that propolis extract cannot cause DNA damage, while MTA can cause apoptosis and Ca(OH2 can cause neucrosis. Conclusion: It can be concluded that propolis extract has genotoxicity effect lower than MTA and Ca(OH2 , but MTA has lower effect on fibroblast BHK-21 cell culture.

  7. Microscopic cleanliness evaluation of the apical root canal after using calcium hydroxide mixed with chlorhexidine, propylene glycol, or antibiotic paste.

    Science.gov (United States)

    da Silva, Juliana M; Andrade Junior, Carlos V; Zaia, Alexandre A; Pessoa, Oscar F

    2011-02-01

    This study evaluated cleaning of the dentinal wall after removal of different calcium hydroxide pastes. Sixty-eight single-rooted teeth were prepared using the step-back technique and randomly divided into 4 groups according to medication used: Ca(OH)2 with 0.2% chlorhexidine solution (Group 1), Ca(OH)2 with propylene glycol (Group 2), Ca(OH)2 with antibiotic paste (ciprofloxacin, metronidazole) and distilled water (Group 3), and Ca(OH)2 with antibiotic paste and propylene glycol (Group 4). The samples were stored at 37 °C and 100% relative humidity for 21 days. The medicaments were removed using 5 mL 1% NaOCl, instrumentation with master apical file, 5 mL 1% NaOCl, patency with the K-file #10, ultrasonic instrumentation, and 10 mL 17% EDTA-T. The specimens were analyzed using scanning electron microscopy and chemical analysis. The Kruskal-Wallis (α = 5%) test showed that were no differences between the experimental groups when comparing Ca(OH)2 removal (P = .0951). The chi-square test (α = 5%) indicated a predominance of Ca(OH)2 obstructing dental tubules in all groups. On the basis of the methodology applied, it was concluded that the apical dentine surface remained equally covered by Ca(OH)2, regardless of the vehicle used.

  8. Will mineral trioxide aggregate replace calcium hydroxide in treating pulpal and periodontal healing complications subsequent to dental trauma? A review.

    Science.gov (United States)

    Bakland, Leif K; Andreasen, Jens O

    2012-02-01

    Mineral trioxide aggregate (MTA) has over the last two decades begun to take the place of calcium hydroxide (CH) in the treatment of a variety of pulpal and periodontal healing complications following dental trauma. These conditions include teeth with: (i) exposed pulps, (ii) immature roots and pulp necrosis, (iii) root fractures and pulp necrosis located in the coronal part of the pulps, and (iv) external infection-related (inflammatory) root resorption. The main reasons for replacing CH with MTA in these situations have generally been the delayed effect when using CH to induce hard tissues, the quality of such induced hard tissues, and finally the dentin weakening effect of CH, which in some instances lead to cervical root fractures in immature teeth. MTA appears, from a relatively few clinical studies, to overcome these shortcomings of CH. The lack of long-term clinical studies, however, may warrant a certain reservation in an unrestricted replacement of CH with MTA. A definite need for randomized clinical studies comparing CH and MTA in trauma healing situations is urgently needed.

  9. Antibacterial Efficacy of Calcium Hydroxide and Chlorhexidine Mixture for Treatment of Teeth with Primary Endodontic Lesions: A Randomized Clinical Trial

    Science.gov (United States)

    Donyavi, Zakiyeh; Ghahari, Parastoo; Esmaeilzadeh, Mohammad; Kharazifard, Mohammadjavad; Yousefi-Mashouf, Rasoul

    2016-01-01

    Introduction: This study compared the root canal microbial count of necrotic teeth after irrigation with 6% sodium hypochlorite (NaOCl) (single session treatment) and two-session root canal treatment with two-week application of calcium hydroxide (CH) mixed with 0.2% chlorhexidine (CHX) as intracanal medicament. Methods and Materials: In this randomized clinical trial, single-rooted necrotic teeth were divided into two groups. Root canal was irrigated with 2 mL of 6% NaOCl in one group, and a mixture of 0.2% CHX and CH powder as an intracanal medicament for two weeks, in the other group. Root canal samples were obtained before and after the intervention and number of colony forming units (CFUs) was counted in each phase. Results: The reduction of Enterococcus faecalis CFU was not significantly different between the two groups (P=0.233) but the CFU of aerobic and anaerobic bacteria was significantly lower in CH+CHX group (Pfaecalis colony counts. Thus, it may be beneficial to carry out primary root canal treatment of necrotic teeth with endodontic lesions in two sessions with intracanal medicaments to achieve predictable results. PMID:27790252

  10. Comparative Evaluation of Clinical and Radiographic Success of Formocresol, Propolis, Turmeric Gel, and Calcium Hydroxide on Pulpotomized Primary Molars: A Preliminary Study

    Science.gov (United States)

    Hugar, Shivayogi M; Hugar, Shweta S; Gokhale, Niraj; Assudani, Harsha

    2017-01-01

    Aims Despite various advents in technology, the present era marks a shift to phytotherapeutics and alternative modalities to conventional endodontic treatments. Newer endodontic modalities have been developed inculcating the ancient system of medicine. The present study was done to compare and evaluate the clinical pulp response and radiographic signs after pulpotomy in four groups of primary molar teeth treated with formocresol (control), propolis extract, turmeric gel, and calcium hydroxide respectively. Materials and methods Following ethical clearance, 90 primary molar teeth in 45 pediatric patients, aged between 4 and 9 years, were selected for pulpotomy. These were then randomly divided by split-mouth technique into two groups as experimental (propolis extract/turmeric gel/calcium hydroxide) and control (formocresol) groups. The patients were followed up for 6 months for clinical and radiographic signs and symptoms to evaluate the success of treatment. Results A comparable clinical and radiographic success rate was seen with all experimental groups as compared to the control (formocresol) group. Conclusion With concerns about the safety of formocresol appearing in the dental and medical literature for more than 20 years, the materials used in this study can be considered as promising alternatives for formocresol in pediatric endodontic treatment. How to cite this article Hugar SM, Kukreja P, Hugar SS, Gokhale N, Assudani H. Comparative Evaluation of Clinical and Radiographic Success of Formocresol, Propolis, Turmeric Gel, and Calcium Hydroxide on Pulpotomized Primary Molars: A Preliminary Study. Int J Clin Pediatr Dent 2017;10(1):18-23.

  11. Early age hydration of calcium sulfoaluminate (synthetic ye'elimite, ) in the presence of gypsum and varying amounts of calcium hydroxide

    KAUST Repository

    Hargis, Craig W.

    2013-06-01

    Suspensions of synthetic ye\\'elimite (C4A3S̄) in a saturated gypsum (CS̄H2) and calcium hydroxide (CH) solution were examined in-situ in a wet cell by soft X-ray transmission microscopy and ex-situ by scanning electron microscopy. The most voluminous hydration product observed was ettringite. Ettringite commonly displayed acicular, filiform, reticulated, and stellate crystal habits. Additionally, pastes with C 4A3S̄, 15% CS̄H2, and varying amounts of CH were prepared and examined with X-ray diffraction (XRD) and isothermal calorimetry. The XRD experiments showed that increasing CH content caused more solid solution (SO4 2 -/OH-) AFm phases to form at early ages (< 1 d) and more monosulfate to form at later ages (> 1 d). Calorimetry indicated that the increased production of solid solution AFm was accompanied with an increase in the initial (< 30 min) rate of heat evolution, and increasing CH generally reduced the time till the second maximum rate of heat evolution due to the formation of ettringite and monosulfate. © 2013 Elsevier Ltd.

  12. Disinfection of dentinal tubules with two different formulations of calcium hydroxide as compared to 2% chlorhexidine: As intracanal medicaments against Enterococcus faecalis and Candida albicans: An in vitro study

    Directory of Open Access Journals (Sweden)

    Dakshita Joy Vaghela

    2011-01-01

    Full Text Available Aim: To evaluate the disinfection of dentinal tubules using calcium hydroxide with propylene glycol and calcium hydroxide with iodoform in silicone oil, as compared to 2% chlorhexidine gel. Materials and Methods: The antimicrobial efficacy of the medicaments against E.faecalis and C.albicans were assessed in vitro, using a dentinal tubule model at depths of 200 μm and 400 μm in extracted single rooted teeth. Saline was taken as the negative control (Group I Results: All three medicaments used in this study exerted antibacterial and antifungal activity. Group II (calcium hydroxide with propylene glycol and Group IV (2% chlorhexidine gel had the highest antimicrobial activity and the differences between their antibacterial activities were not statistically significant. Group III (calcium hydroxide with iodoform in silicone oil and Group IV had the highest antifungal activity and the differences between their antifungal activities were not statistically significant. The inhibition of growth at 200 μm and 400 ΅m was uniform, with no statistical difference. Conclusions: Two percent chlorhexidine gel was effective against both E.faecalis and C.albicans. Calcium hydroxide with propylene glycol was the most effective intracanal medicament along with 2% chlorhexidine against E.faecalis, whereas, calcium hydroxide with iodoform in silicone oil was the most effective intracanal medicament along with 2% chlorhexidine against C.albicans.

  13. Comparison of the efficacy of ethylene diamine tetraacetic acid and maleic acid in the removal of three calcium hydroxide intra-canal dressings: A spiral computerized tomography volumetric analysis

    Directory of Open Access Journals (Sweden)

    Mohan Thomas Nainan

    2013-01-01

    Full Text Available Aim: To assess the efficacy of 17% ethylene diamine tetra acetic acid and 7% maleic acid in the removal of 3 calcium hydroxide preparations placed as intracanal medicaments. Materials and Methods: The root canals of 60 single rooted premolars were prepared with a step back technique and randomly assigned into 3 experimental groups (n = 20. Group A was filled with plain calcium hydroxide mixed with distilled water in which barium sulfate was added for radio opacity, Group B was filled with Apexcal and Group C was filled with Metapex. After 7 days each group was divided into 2 sub groups (n = 10. The medicaments were retrieved with 17% EDTA (first sub group and 7% maleic acid (second sub group. Along with the above irrigants manual and ultrasonic agitation was used. The pre and post removal volume of medicaments in root canals were measured using spiral computerized tomography. The percentage difference was calculated and statistically analyzed using Kruskal Wallis and Mann Whitney U test. Results: 17% EDTA and 7% maleic acid efficiently removed calcium hydroxide, distilled water mixture (P = 0.218 and Apexcal (P = 0.684, whereas 7% maleic acid showed better retrieval capability of Metapex than 17% EDTA (P = 0.002. Conclusion: Calcium hydroxide, distilled water mixture and polyethylene glycol based calcium hydroxide were efficiently removed by 17% EDTA and 7% maleic acid. 7% maleic acid removed silicone oil based calcium hydroxide preparation better than 17% EDTA.

  14. Immunolocalization of fibronectin during reparative dentinogenesis in rat molor teeth after pulp capping with mineral trioxide aggregate or calcium hydroxide.

    Science.gov (United States)

    Bal, Cenkhan; Oztas, Nurhan; Cincik, Mehmet; Baris, Emre

    2011-11-01

    The aim of this study was to evaluate the immunolocalization of fibronectin during reparative dentinogenesis in rat teeth after pulp capping with mineral trioxide aggregate (MTA) or calcium hydroxide (Ca(OH)2). The pulps of 72 upper and lower first molar teeth from 18 male Wistar rats were experimentally exposed. The pulps were capped with MTA or (Ca(OH)2); final restoration followed with zinc oxide and eugenol cement. The animals were euthanized at, respectively, one, three, seven and fourteen days postoperatively. At day one, all groups showed varying degrees of inflammation, from mild to severe. There was no positive reaction for fibronectin at day one. After three days, a partial acute pulpitis was observed in the Ca(OH)2 group. There was less inflammation in the MTA group (p<0.05), and a layer of fibrin barrier was observed along the pulp walls of the MTA material. The layer of fibrodentin formation showed positive reaction for fibronectin. At seven days, the Ca(OH)2 group showed mild inflammation and demonstrated more immunostaining for fibronectin than the Ca(OH)2 group (p<0.05) at three days. Pulps capped with MTA at seven days showed thicker fibrin barrier formation than the MTA group at three days and more immunostaining for fibronectin in whole groups (p<0.05). At fourteen days, there was no positive reaction for fibronectin in either the MTA or Ca(OH)2 group. It seems MTA showed better biocompability properties with the dental pulp tissue, inducing the expression of reparative molecule fibronectin compared with Ca(OH)2. Therefore, MTA may be a better choice for pulp capping procedures.

  15. Calcium hydroxide dressing residues after different removal techniques affect the accuracy of Root-ZX apex locator

    Science.gov (United States)

    Eymirli, Ayhan; Uyanik, Mehmet Özgür; Çalt, Semra; Nagas, Emre

    2015-01-01

    Objectives This study compared the ability of several techniques to remove calcium hydroxide (CH) from the root canal and determined the influence of CH residues on the accuracy of the electronic apex locator. Materials and Methods Root canals of 90 human maxillary lateral incisors with confirmed true working length (TWL) were prepared and filled with CH. The teeth were randomly assigned to one of the experimental groups according to the CH removal technique (n = 14): 0.9% saline; 0.9% saline + master apical file (MAF); 17% ethylenediamine tetraacetic acid (EDTA); 17% EDTA + MAF; 5.25% sodium hypochlorite (NaOCl); 5.25% NaOCl + MAF. Six teeth were used as negative control. After CH removal, the electronic working length was measured using Root-ZX (Morita Corp.) and compared with TWL to evaluate Root-ZX accuracy. All specimens were sectioned longitudinally, and the area of remaining CH (CH) and total canal area were measured using imaging software. Results The EDTA + MAF and NaOCl + MAF groups showed better CH removal than other groups (p 85% within a tolerance of ± 1.0 mm (p < 0.05). There was strong negative correlation between amount of CH residues and EAL accuracy (r = -0.800 for ± 0.5 mm; r = -0.940 for ± 1.0 mm). Conclusions The mechanical instrumentation improves the CH removal of irrigation solutions although none of the techniques removed the dressing completely. Residues of CH medication in root canals affected the accuracy of Root-ZX adversely. PMID:25671212

  16. Pulp tissue vacuolization and necrosis after direct pulp capping with calcium hydroxide and transforming growth factor-β1

    Directory of Open Access Journals (Sweden)

    Sri Kunarti

    2008-03-01

    Full Text Available Mechanical pulp exposure by a rotary cutting instrument or a hand-cutting instrument often happens in deep caries. Application of protective dressing can protect the pulp from additional injury by facilitating healing and repair. Pulp capping has been suggested as one treatment of choice after pulp exposure to maintain pulp vitality. TGF-β1 is growth factor that has important rule in wound healing. The application of Ca(OH2 and exogenous TGF-β1 as direct pulp capping tr4eatment must be experimented in-vivo to see the vacuolization and necrosis in 7, 14, and 21 days after application. This research was done in vivo experiment from orthodontic patients indicated for premolar extraction, between ages 10–15 years. A class V cavity preparation was created in the buccal aspect 1 mm above gingival margin until pulp exposure. Cavity was irrigated slowly with saline solution and dried with a sterile small cotton pellet. Group 1 calcium hydroxide was applied as manufacture procedure. Group 2, the sterile absorbable collagen membrane used, as inert carrier of TGF-β1 was soaked with 5 ml. All groups were covered by a Teflon pledge to separate pulp capping agent from glass ionomer cement restoration. Teeth extracted in 7, 14 and 21 days after treatment. All samples were hystopathologically examined. There were significant difference of TGF-β1 (p < 0.05 in the vacuolization day 14th and 21th compared with 7th. there were not significant difference in necrosis for all variables. Vacuolization and necrosis decreased in the application of TGF-β1.

  17. Sonic versus ultrasonic activation for removal of calcium hydroxide from curved root canals: an in vitro study.

    Directory of Open Access Journals (Sweden)

    Tamara Cid

    2014-12-01

    Full Text Available To compare the remaining calcium hydroxide (Ca(OH2 coated area in the apical third of curved canals after sonic and ultrasonic activation using Scanning Electron Microscope (SEM. Permanent mandibular molars were collected. Those which radiographically presented a curvature between 15º and 30° in the mesial root were included. A total of 39 mesiolinguales canals were instrumented with rotary ProTaper and filled with Ca(OH2 mixed with propylene glycol. They were randomly divided into three groups according to the type of removal. Group I: three inserts with File F2 and 2ml of 5.25% sodium hypochlorite (NaOCl irrigation between each insertion. Group II: three sonic activations, irrigattion with 2ml of 5.25% NaOCl between activations. Group III: three ultrasonic activations irrigating with 2ml of 5.25% NaOCl between activations. Three root canals were left without filling and other three were completely filled as positive and negative control, respectively. Then, they were fractured lengthwise to get two sections. The apical third of the root canal of each section was taken x-rays with SEM and subsequently, in an area of 100.000um2, the remaining Ca(OH2 coated surface from both sections was measured using ImageJ 1.47. They were analyzed with one-way ANOVA using Graph Pad-Prism (5.01. The percentage of the remaining Ca(OH2 coated area in group I was 62.93%, 51.77% in group II, and 58.90% in group III. There were no significant differences between the three groups (p>0.01. There are no significant differences in the percentage of the remaining Ca(OH2 coated area in the apical third of curved root canals when comparing sonic and ultrasonic activation using SEM.

  18. The efficacy of the self-adjusting file and ProTaper for removal of calcium hydroxide from root canals

    Directory of Open Access Journals (Sweden)

    Gisele Faria

    2013-07-01

    Full Text Available OBJECTIVE: The goal of this study was to evaluate the efficacy of the Self-Adjusting File (SAF and ProTaper for removing calcium hydroxide [Ca(OH2] from root canals. MATERIAL AND METHODS: Thirty-six human mandibular incisors were instrumented with the ProTaper system up to instrument F2 and filled with a Ca(OH2-based dressing. After 7 days, specimens were distributed in two groups (n=15 according to the method of Ca(OH2 removal. Group I (SAF was irrigated with 5 mL of NaOCl and SAF was used for 30 seconds under constant irrigation with 5 mL of NaOCl using the Vatea irrigation device, followed by irrigation with 3 mL of EDTA and 5 mL of NaOCl. Group II (ProTaper was irrigated with 5 mL of NaOCl, the F2 instrument was used for 30 seconds, followed by irrigation with 5 mL of NaOCl, 3 mL of EDTA, and 5 mL of NaOCl. In 3 teeth Ca(OH2 was not removed (positive control and in 3 teeth canals were not filled with Ca(OH2 (negative control. Teeth were sectioned and prepared for the scanning electron microscopy. The amounts of residual Ca(OH2 were evaluated in the middle and apical thirds using a 5-score system. RESULTS: None of the techniques completely removed the Ca(OH2 dressing. No difference was observed between SAF and ProTaper in removing Ca(OH2 in the middle (P=0.11 and the apical (P=0.23 thirds. CONCLUSION: The SAF system showed similar efficacy to rotary instrument for removal of Ca(OH2 from mandibular incisor root canals.

  19. Structural and nano-mechanical properties of Calcium Silicate Hydrate (C-S-H) formed from alite hydration in the presence of sodium and potassium hydroxide

    Energy Technology Data Exchange (ETDEWEB)

    Mendoza, Oscar, E-mail: oamendoz@unal.edu.co [Grupo del Cemento y Materiales de Construcción (CEMATCO). Universidad Nacional de Colombia, Facultad de Minas, Medellín (Colombia); Giraldo, Carolina [Cementos Argos S.A., Medellín (Colombia); Camargo, Sergio S. [Engenharia Metalúrgica e de Materiais, Universidade Federal do Rio de Janeiro/COPPE, Rio de Janeiro (Brazil); Tobón, Jorge I. [Grupo del Cemento y Materiales de Construcción (CEMATCO). Universidad Nacional de Colombia, Facultad de Minas, Medellín (Colombia)

    2015-08-15

    This research evaluates the effect of sodium and potassium hydroxide on the structure and nano-mechanical properties of Calcium Silicate Hydrate (C-S-H) formed from the hydration of pure alite. Monoclinic (MIII) alite was synthesized and hydrated, using water-to-alite ratios of 0.5 and 0.6 and additions of 10% NaOH and KOH by weight of alite. Based on results of X-ray diffraction, isothermal calorimetry, thermogravimetric analysis, Nuclear Magnetic Resonance and nanoindentation, two different effects of the alkaline hydroxides on the hydration reaction of alite, both at early and later ages, can be identified: (i) a differentiated hydration process, attributed to an enhancement in calcium hydroxide (CH) precipitation and a stimulation of the C-S-H nuclei; and (ii) an increase in the elastic modulus of the C-S-H aggregations, attributed to an electrostatic attraction between positive charges from the alkaline cations and negative charges from the C-S-H structure.

  20. Scientific Opinion on the safety assessment of the active substances, sodium erythorbate, sodium carbonate, sodium bicarbonate, iron sulphate, activated carbon, cellulose, calcium hydroxide, calcium chloride and water, for use as active system in food contact materials

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids (CEF

    2014-02-01

    Full Text Available This scientific opinion of EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids deals with the safety assessment of the active substances sodium erythorbate, sodium carbonate, sodium bicarbonate, iron sulfate, activated carbon, cellulose, calcium hydroxide, calcium chloride and water, used in mixture which is packed into sachets for absorbing oxygen/carbon dioxide emitting from/into the headspace surrounding packed food. All substances of this formulation have been evaluated and approved for use as additives in plastic food contact materials or as food additives. No migration of calcium, iron and sodium ions was detected. No volatile organic compounds other than carbon dioxide were detected at the limit of detection of 0.5 μg/l. The CEF Panel concluded that the use of the substances sodium erythorbate, sodium carbonate, sodium bicarbonate, iron sulfate, activated carbon, cellulose, calcium hydroxide, calcium chloride and water does not raise a safety concern when used in oxygen absorber/carbon dioxide emitter systems, in sachets that prevent the physical release of their contents into the food. The sachets are to be placed in the headspace of the packaging and as such may come into occasional contact with the food, e.g. during handling. The sachet should not come into direct contact with liquid foods or foods that have and external aqueous liquid phase on the surface (liquid or exudates.

  1. Common Calcium Hydroxide Preparation and Its Application in the Oral Medicine%常用氢氧化钙制剂及其在口腔内科学中的应用

    Institute of Scientific and Technical Information of China (English)

    吴春锋

    2016-01-01

    口腔科常用氢氧化钙制剂包括放射线阻射氢氧化钙复合物、氢氧化钙甘油、ZT胶氢氧化钙混合剂和可见光固化氢氧化钙,可用于根管消毒、根管充填、根尖诱导成形术、活髓切断术和盖髓术。用于治疗口腔内科疾病操作简单,成本低廉,治疗效果显著。但应合理应用氢氧化钙制剂,充分认识其优势和不足,使之充分发挥治疗作用。%The common calcium hydroxide preparations in the oral department include the radiation resistance calcium hy-droxide compound, calcium hydroxide glycerol, ZT glue alcium hydroxide mixture, visible light solidified alcium hydroxide, which can be used in the root canal disinfection, root canal filling, apexifieation, vital pulpotomy and capping, the treatment effect of diseases in the oral medicine is obvious with easy operation and cheap cost, but we should rationally use the calci-um hydroxide preparation, fully recognize their advantages and disadvantages, and make them fully play a treatment role.

  2. Comparative Evaluation of Propolis, Metronidazole with Chlorhexidine, Calcium Hydroxide and Curcuma Longa Extract as Intracanal Medicament Against E.faecalis– An Invitro Study

    Science.gov (United States)

    Nair, Rashmi; Asrani, Hemant

    2015-01-01

    Introduction The increase of potential side effects and safety concerns of conventional medicaments have led to the recent popularity of herbal alternative medications. The herbal products are known for its high antimicrobial activity, biocompatibility, anti-inflammatory and antioxidant properties. Aim The purpose of this study was to investigate and compare the effectiveness of Propolis, Metronidazole with Chlorhexidine gel, Curcuma Longa and Calcium Hydroxide for elimination of E.faecalis bacteria in extracted teeth samples. Materials and Methods Ninety extracted single rooted intact teeth were taken for the study. Decoronation, removal of apices and chemomechanical preparation was done for all samples. These sterilized samples were then contaminated with pure culture of E.faecalis under laminar flow. The samples were incubated for a period of 21 days. The infected samples were assigned to 5 groups: Group I- Propolis; Group II- Metronidazole with Chlorhexidine gel; Group III- Calcium hydroxide; Group IV- Curcuma Longa; and control group- Saline. Efficacy of newer intracanal medicaments against E.faecalis were carried out in the samples at the end of 1, 2 & 5 days for each group with the help of colorimeter. Student paired t-test, ANOVA and multiple tukey test were used for statistical analysis. Results The value of optical density was statistically significant in all groups when compared to that of control group. Group I (Propolis) produced better antimicrobial efficacy followed by Chlorhexidine Metronidazole combination, Curcuma Longa and Calcium hydroxide. Conclusion Within the limitations of this study, it can be concluded that Propolis showed better antimicrobial properties against E.faecalis than other medicaments. PMID:26673857

  3. The effects of calcium hydroxide-treated whole-plant and fractionated corn silage on intake, digestion, and lactation performance in dairy cows.

    Science.gov (United States)

    Cook, D E; Bender, R W; Shinners, K J; Combs, D K

    2016-07-01

    The objective of this trial was to evaluate, in dairy cattle, the effects of calcium hydroxide treatment of whole-plant corn and a treatment applied to the bottom stalk fraction of the corn plant, achieved by harvesting corn in 2 crop streams. The treatments were calcium hydroxide-treated corn silage (TRTCS), toplage supplemented with calcium hydroxide-treated stalklage (TPL), a positive control of brown midrib corn silage (BMR), and a negative control of conventional whole-plant corn silage (WPCS). The toplage was harvested at a height of 82 cm with 2 of the 6 rows set as ear-snapping to incorporate higher tissues into the stalklage. Stalklage was harvested at 12 cm, and other corn silages were harvested at 27 cm. Sixteen pens, each with 8 Holstein cows averaging 70±25 d in milk and 46±11 kg of milk d(-1), were assigned 4 per treatment in a completely randomized design. The diet was approximately 40% corn silage, 20% alfalfa silage, and 40% concentrate on a dry matter basis. A 2-wk covariate period with conventional corn silage was followed by an 8-wk treatment period in which the 4 corn silage treatments were the only effective difference in diets. Cows fed TPL and TRTCS consumed more (1.9 and 1.4 kg of organic matter d(-1), respectively) than did cows fed WPCS. Milk yield was greater for cows fed BMR, TPL, and TRTCS. Cows fed BMR and TPL produced 2.9 and 2.7 kg d(-1), respectively, more energy-corrected milk (ECM) than cows fed WPCS, and cows fed TRTCS had the greatest ECM production (4.8 kg of ECM d(-1) greater than cows fed WPCS). No differences in body weight or body condition scored were observed. Milk fat concentration was similar among treatments and milk protein concentration was reduced for TRTCS. Starch and neutral detergent fiber digestibility were greater for cows fed TRTCS.

  4. Efficacy of Triple Antibiotic Paste, Moxifloxacin, Calcium Hydroxide And 2% Chlorhexidine Gel In Elimination of E. Faecalis: An In vitro Study

    Science.gov (United States)

    Sekhar, K.S; Gupta, Pankaj; Tejolatha, Bellam; Gupta, Anjali; Kashyap, Shruti; Desai, Veena; Farista, Shanin

    2017-01-01

    Introduction Root canal treatment is incomplete without usage of intra canal medicaments. They help in the reduction of bacterial count and its by-products, making canals clean and decreasing postoperative pains. Aim The aim of this study was to evaluate and compare the antimicrobial activity of triple antibiotic paste, Moxifloxacin, calcium hydroxide and 2% Chlorhexidine (CHX) gel in elimination of Enterococcous faecalis (E. faecalis). Materials and Methods Seventy-five root blocks were obtained from extracted single rooted human teeth. The canal diameter was increased using Gates- Glidden drill up to size 3 and then contaminated with E. faecalis for 21 days. The contaminated samples were then divided into following 5 groups. Group 1: Saline (negative group), Group 2: Calcium hydroxide Ca(OH)2, Group 3: 2% CHX gel, Group 4: Triple Antibiotic Paste (TAP) (50 μg – metronidazole of 400 mg, 50 μg – minocycline of 100 mg, 50 μg – ciprofloxacin of 100 mg) and Group 5: Moxifloxacin (50 μg – moxifloxacin of 400 mg). Dentin debris was obtained at the end of first, 7th, and 10th day using Gates Glidden drill sizes 4 and 5. The bacterial load was assessed by counting the number of Colony Forming Units (CFUs). The data were analyzed with the ANOVA and Post-Hoc tests to assess the differences in antibacterial efficacy between groups (p=<0.001). Results A 2% CHX gel alone completely inhibited the growth of E. faecalis after one, seven and 10 days. The 2% CHX gel was the most effective medicament against E. faecalis, as it showed significant differences with normal saline, calcium hydroxide, Moxifloxacin or triple antibiotic paste at all time intervals. The triple antibiotic paste group showed a moderate antibacterial effect as its difference with all group was significantly better at all days. Moxifloxacin was more effective than calcium hydroxide on 7th and 10th day. Conclusion Best antimicrobial efficacy was shown by 2% CHX gel. Moxifloxacin was equally efficient

  5. Antibacterial effect of calcium hydroxide combined with chlorhexidine on Enterococcus faecalis: a systematic review and meta-analysis

    Directory of Open Access Journals (Sweden)

    Masoud SAATCHI

    2014-10-01

    Full Text Available Objective: Enterococcus faecalis (E. faecalis is the most frequently isolated strain in failed endodontic therapy cases since it is resistant to calcium hydroxide (CH. Whether a combination of CH and chlorhexidine (CHX is more effective than CH alone against E. faecalis is a matter of controversy. Thus, the aim of this study was to conduct a systematic review and meta-analysis of the literature. Material and Methods: A comprehensive search in PubMed, EMbase, EBSCOhost, The Cochrane Library, SciELO, and BBO databases, Clinical trials registers, Open Grey, and conference proceedings from the earliest available date to February 1, 2013 was carried out and the relevant articles were identified by two independent reviewers. Backward and forward search was performed and then inclusion and exclusion criteria were applied. The included studies were divided into "comparisons" according to the depth of sampling and dressing period of each medicament. Meta-analysis was performed using Stata software 10.0. The level of significance was set at 0.05. Results: Eighty-five studies were retrieved from databases and backward/forward searches. Fortyfive studies were considered as relevant (5 in vivo, 18 in vitro, 18 ex vivo, and 4 review articles. Nine studies were included for meta-analysis. Inter-observer agreement (Cohen kappa was 0.93. The included studies were divided into 21 comparisons for meta-analysis. Chi-square test showed the comparisons were heterogeneous (p<0.001. Random effect model demonstrated no significant difference between CH/CHX mixture and CH alone in their effect on E. faecalis (p=0.115. Conclusions: According to the evidence available now, mixing CH with CHX does not significantly increase the antimicrobial activity of CH against E. faecalis. It appears that mixing CH with CHX does not improve its ex vivo antibacterial property as an intracanal medicament against E. faecalis. Further in vivo studies are necessary to confirm and correlate

  6. An in vitro evaluation of the antimicrobial efficacy of Curcuma longa, Tachyspermum ammi, chlorhexidine gluconate, and calcium hydroxide on Enterococcus faecalis

    Directory of Open Access Journals (Sweden)

    Hemanshi Kumar

    2013-01-01

    Full Text Available Aim and Objectives: This in vitro study was designed to comparatively evaluate the antimicrobial efficacy of Curcuma longa (turmeric - T 1 -10%, T 2 -20%; Tachyspermum ammi (ajwain - A 1 -10%, A 2 -20%; chlorhexidine (CHX gluconate gel (hexigel - 1%; and calcium hydroxide (10% as intracanal medicaments against Enterococcus faecalis. Materials and Methods: Agar plates were prepared using brain-heart infusion (BHI agar. Cultures of E. faecalis were grown in BHI broth at 37°C. Well diffusion method was used to derive results. Plates were inoculated for 72 h at 37°C and microbial zones of inhibition were recorded. Statistical analysis was performed with repeated measures analysis of variance. Results: C. longa (T 2 -20% and CHX gluconate gel (hexigel - CHX-1% showed larger zones of microbial inhibition than C. longa (T 1 -10% that were statistically significant (P < 0.05 and were highly significant when compared to T. ammi (ajwain - A 1 and A 2 and calcium hydroxide. Conclusion: C. longa can be used as intracanal medicament in endodontic failure cases.

  7. An in vitro evaluation of the antimicrobial efficacy of Curcuma longa, Tachyspermum ammi, chlorhexidine gluconate, and calcium hydroxide on Enterococcus faecalis

    Science.gov (United States)

    Kumar, Hemanshi

    2013-01-01

    Aim and Objectives: This in vitro study was designed to comparatively evaluate the antimicrobial efficacy of Curcuma longa (turmeric – T1-10%, T2-20%); Tachyspermum ammi (ajwain – A1-10%, A2-20%); chlorhexidine (CHX) gluconate gel (hexigel – 1%); and calcium hydroxide (10%) as intracanal medicaments against Enterococcus faecalis. Materials and Methods: Agar plates were prepared using brain-heart infusion (BHI) agar. Cultures of E. faecalis were grown in BHI broth at 37°C. Well diffusion method was used to derive results. Plates were inoculated for 72 h at 37°C and microbial zones of inhibition were recorded. Statistical analysis was performed with repeated measures analysis of variance. Results: C. longa (T2-20%) and CHX gluconate gel (hexigel – CHX-1%) showed larger zones of microbial inhibition than C. longa (T1-10%) that were statistically significant (P < 0.05) and were highly significant when compared to T. ammi (ajwain – A1 and A2) and calcium hydroxide. Conclusion: C. longa can be used as intracanal medicament in endodontic failure cases. PMID:23716967

  8. Comparing the reinforcing effects of a resin modified glassionomer cement, Flowable compomer, and Flowable composite in the restoration of calcium hydroxide-treated immature roots in vitro

    Directory of Open Access Journals (Sweden)

    S Prathibha Rani

    2011-01-01

    Full Text Available One hundred and sixty human permanent central incisors were enlarged to a 120 file size after crown removal procedure to simulate immature teeth. The root canals were filled with calcium hydroxide and stored for 15 days (phase I, 30 days (phase II, 90 days (phase III, and 180 days (Phase IV. At the end of these selected time periods, calcium hydroxide was cleaned off the root canals of forty teeth that were randomly selected and obturated with gutta-percha points in the apical 2 mm of the root canals with a sealer. The specimens were further equally divided into four groups. Unrestored Group I served as control and the root canals of teeth in the other three group specimens were reinforced with resin modified glassionomer cement (RMGIC (Group II, Flowable Compomer (Group III, and Flowable Composite (Group IV, respectively, using a translucent curing post. All specimens were subjected to compressive force using an Instron Testing machine, until fracture occurred. All the materials evaluated substantially reinforced the root specimens compared to the control. At the end of 180 days, Flowable composites showed maximum reinforcement compared to the other groups; however, no significant differences were found between the reinforcement capabilities of Flowable Compomer and RMGIC.

  9. Comparing the reinforcing effects of a resin modified glassionomer cement, Flowable compomer, and Flowable composite in the restoration of calcium hydroxide-treated immature roots in vitro.

    Science.gov (United States)

    Prathibha, Rani S

    2011-01-01

    One hundred and sixty human permanent central incisors were enlarged to a 120 file size after crown removal procedure to simulate immature teeth. The root canals were filled with calcium hydroxide and stored for 15 days (phase I), 30 days (phase II), 90 days (phase III), and 180 days (Phase IV). At the end of these selected time periods, calcium hydroxide was cleaned off the root canals of forty teeth that were randomly selected and obturated with gutta-percha points in the apical 2 mm of the root canals with a sealer. The specimens were further equally divided into four groups. Unrestored Group I served as control and the root canals of teeth in the other three group specimens were reinforced with resin modified glassionomer cement (RMGIC) (Group II), Flowable Compomer (Group III), and Flowable Composite (Group IV), respectively, using a translucent curing post. All specimens were subjected to compressive force using an Instron Testing machine, until fracture occurred. All the materials evaluated substantially reinforced the root specimens compared to the control. At the end of 180 days, Flowable composites showed maximum reinforcement compared to the other groups; however, no significant differences were found between the reinforcement capabilities of Flowable Compomer and RMGIC.

  10. MTA and calcium hydroxide for pulp capping MTA e hidróxido de cálcio para proteção pulpar direta

    Directory of Open Access Journals (Sweden)

    Alexandra Mussolino de Queiroz

    2005-06-01

    Full Text Available This study evaluated the biocompatibility of mineral trioxide aggregate (MTA after direct capping of exposed pulp tissue in dog's teeth. Class I cavities were prepared in 26 teeth from 3 adult dogs. MTA was applied over the exposed pulp in 13 teeth and paste of calcium hydroxide plus distilled water (control was applied in the remaining 13 teeth. After 90 days, the animals were killed; the maxilla and mandible were dissected and sectioned to obtain individual roots. The samples were processed histologically. The pulp and periapical response observed with the use of MTA was similar to that of calcium hydroxide paste. In all specimens, there was a dentin bridge obliterating the exposure, an intact odontoblastic layer, no inflammatory cells, normal connective pulp tissue, normal apical and periapical regions and no bone tissue changes. Similar to calcium hydroxide, MTA presented excellent response when used for direct pulp capping.O objetivo deste trabalho foi avaliar a biocompatibilidade do agregado de trióxido mineral (MTA, após proteção pulpar direta em dentes de cães. Foram preparadas cavidades de Classe I, em 26 dentes de 3 cães adultos. O MTA foi aplicado sobre 13 dentes e a pasta de hidróxido de cálcio (grupo controle foi aplicada sobre os 13 dentes remanescentes. Após 90 dias, os animais foram mortos, a maxila e a mandíbula foram dissecadas e os dentes foram seccionados para obtenção de raízes individualizadas. Os espécimes foram processados histologicamente. A resposta do tecido pulpar e periapical foi semelhante para o MTA e o hidróxido de cálcio. Em todos os espécimes havia ponte de dentina obliterando o local da exposição pulpar, camada odontoblástica íntegra, ausência de células inflamatórias, tecido pulpar normal, e ausência de alterações na região periapical e óssea. Da mesma maneira que o hidróxido de cálcio, o MTA apresentou excelente biocompatibilidade quando usado para proteção pulpar direta.

  11. Comparative evaluation of calcium silicate-based dentin substitute (Biodentine®) and calcium hydroxide (pulpdent) in the formation of reactive dentin bridge in regenerative pulpotomy of vital primary teeth: Triple blind, randomized clinical trial

    Science.gov (United States)

    Grewal, Navneet; Salhan, Rubica; Kaur, Nirapjeet; Patel, Hemal Bipin

    2016-01-01

    Background: Considering the biological concerns of calcium hydroxide (CH) as a pulpotomy agent, an alternative silicate based dentin substitute i.e. Biodentine (Ca3SiO5) was evaluated clinically and radiographically. Aims: To evaluate the effectiveness of dentin substitute (Biodentine) in regenerative pulpotomy of vital primary teeth that would giv a biological base to its use in forming reactive dentin bridge and overcoming the drawbacks of calcium hydroxide. Material and Methods: Randomised clinical trial on 40 bilateral carious primary molars in 20 participant children (aged 5-10 years) was carried out by same operator using Ca3SiO5(group-1) and CH (group-2) as vital pulpotomy agents. Blinded clinical and radiographic outcomes were observed at 3, 6 and 12 months interval. Results: Clinical outcomes of both protocols were analysed using Pearson's chi-square test applied at P < 0.05. Descriptive statistics were expressed as mean increase in dentin bridge formation in mms from two reference points in standardized radiographs using paired ‘t’- test at baseline and 12 months and found to be statistically significant (P < 0.05) in group-1 when compared with group-2. Conclusion: Group-1 revealed statistically favourable regenerative potential along with clinical success compared to group 2 thereby sharing both indications and mode of action with CH, but without its drawbacks of physical and clinical properties. PMID:27994411

  12. Comparative evaluation of calcium silicate-based dentin substitute (Biodentine® and calcium hydroxide (pulpdent in the formation of reactive dentin bridge in regenerative pulpotomy of vital primary teeth: Triple blind, randomized clinical trial

    Directory of Open Access Journals (Sweden)

    Navneet Grewal

    2016-01-01

    Full Text Available Background: Considering the biological concerns of calcium hydroxide (CH as a pulpotomy agent, an alternative silicate based dentin substitute i.e. Biodentine (Ca3SiO5 was evaluated clinically and radiographically. Aims: To evaluate the effectiveness of dentin substitute (Biodentine in regenerative pulpotomy of vital primary teeth that would giv a biological base to its use in forming reactive dentin bridge and overcoming the drawbacks of calcium hydroxide. Material and Methods: Randomised clinical trial on 40 bilateral carious primary molars in 20 participant children (aged 5-10 years was carried out by same operator using Ca3SiO5(group-1 and CH (group-2 as vital pulpotomy agents. Blinded clinical and radiographic outcomes were observed at 3, 6 and 12 months interval. Results: Clinical outcomes of both protocols were analysed using Pearson's chi-square test applied at P < 0.05. Descriptive statistics were expressed as mean increase in dentin bridge formation in mms from two reference points in standardized radiographs using paired 't'- test at baseline and 12 months and found to be statistically significant (P < 0.05 in group-1 when compared with group-2. Conclusion: Group-1 revealed statistically favourable regenerative potential along with clinical success compared to group 2 thereby sharing both indications and mode of action with CH, but without its drawbacks of physical and clinical properties.

  13. A comparison of the pulpal response to freeze-dried bone, calcium hydroxide, and zinc oxide-eugenol in primary teeth in two cynomolgus monkeys.

    Science.gov (United States)

    Fadavi, S; Anderson, A W

    1996-01-01

    This study assessed the pulp healing response to human freeze-dried bone (FDB) in two cynomolgus monkeys using 36 noncarious primary teeth pulpotomized and randomly assigned to three medicaments. FDB was applied on the pulp stumps and covered with sterile tin foil as experimental group. The two other groups received either calcium hydroxide [Ca(OH)2], or IRM (reinforced ZOE). All teeth were restored with amalgam. One animal was sacrificed at 6 weeks and the other 6 months after treatment. Teeth were extracted and placed in 10% formalin. Histological evaluation indicated that 100% of teeth treated with FDB had vital pulps compared with 75% of the Ca(OH)2 group after 6 weeks. Dentin bridges were present in 87.5% of FDB versus 75% of Ca(OH)2 group. Inflammatory cells were absent or mild in 100% of FDB-treated versus 75% of the Ca(OH)2 group. After 6 months, 83.3% of FDB-treated teeth had vital pulps compared with the Ca(OH)2 group, which showed 100% pulpal necrosis. In FDB-treated pulps, 100% of teeth showed dentin bridges versus 50% of teeth treated with Ca(OH)2. Inflammatory cells were absent or mildly present in 83.3% of FDB-treated teeth while 100% of Ca(OH)2 showed moderate to severe inflammation. IRM-treated teeth all showed pulpal necrosis after 6 months. We concluded that FDB was superior to calcium hydroxide in treating primary pulp dentition in cynomolgus monkeys.

  14. Acrylic acid-allylpolyethoxy carboxylate copolymer dispersant for calcium carbonate and iron(III) hydroxide scales in cooling water systems

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Guangqing; Huang, Jingyi; Zhou, Yuming; Yao, Qingzhao; Ling, Lei; Zhang, Peixin; Fu, Change [Southeast Univ., Nanjing (China). School of Chemistry and Chemical Engineering; Wu, Wendao; Sun, Wei; Hu, Zhengjun [Jianghai Chemical Co., Ltd., Changzhou (China)

    2012-05-15

    A novel environmentally friendly type of calcium carbonate and iron(III) scale inhibitor (ALn) was synthesized. The anti-scale property of the Acrylic acid-allylpolyethoxy carboxylate copolymer (AA-APELn or ALn) towards CaCO{sub 3} and iron(III) in the artificial cooling water was studied through static scale inhibition tests. The observation shows that both calcium carbonate and iron(III) inhibition increase with increasing the degree of polymerization of ALn from 5 to 15, and the dosage of ALn plays an important role on calcium carbonate and iron(III)-inhibition. The effect on formation of CaCO{sub 3} was investigated with a combination of scanning electronic microscopy (SEM), Transmission electron microscopy (TEM), X-ray powder diffraction (XRD) analysis and Fourier transform infrared spectrometer, respectively. The results showed that the ALn copolymer not only influences calcium carbonate crystal morphology and crystal size but also the crystallinity. The crystallization of CaCO{sub 3} in the absence of inhibitor was rhombohedral calcite crystal, whereas a mixture of calcite with vaterite crystals was found in the presence of the ALn copolymer. Inhibition mechanism is proposed that the interactions between calcium or iron ions and polyethylene glycol (PEG) are the fundamental impetus to restrain the formation of the scale in cooling water systems. (orig.)

  15. Magnesium Hydroxide

    Science.gov (United States)

    Magnesium hydroxide is used on a short-term basis to treat constipation.This medication is sometimes prescribed ... Magnesium hydroxide come as a tablet and liquid to take by mouth. It usually is taken as ...

  16. Effects of chopping, and soaking in water, hydrochloric acidic and calcium hydroxide solutions on the nutritional value of Acacia villosa for goats

    Energy Technology Data Exchange (ETDEWEB)

    Wina, E. [Research Institute for Animal Production, Bogor (Indonesia)]. E-mail: winabudi@yahoo.com; Tangendjaja, B.; Susana, I.W.R. [Research Institute for Animal Production, Bogor (Indonesia)

    2005-08-19

    Acacia villosa, a thornless shrub legume, has potential as a feed supplement for ruminants if anti-nutritional factors, especially tannins, can be overcome. The effects of chopping and soaking the leaves on the amounts of tannin in the extracting solution and that left in the recovered leaves were studied. The tannin and non-tannin phenolics were solubilized in the extracting solution and the amount was increased with the soaking time. Soaking in calcium hydroxide solution, hydrochloric acid or water removed 41-76% of tannin and total phenolics removed from the recovered leaves. Soaking of the leaves also removed fermentable materials and reduced the gas production. In the first of two digestibility experiments, three groups of goats received one of these diets, those were: (1) sugar cane tops: unsoaked Acacia leaves (7:3), (2) sugar cane tops: water soaked Acacia leaves (7:3) and (3) sugar cane tops: water soaked Acacia leaves (7:3) + 100 g/day of cassava flour. Live weight of goats was measured every 2 weeks and a large increase in average daily gain was obtained for goats fed diet containing water soaked leaves and cassava flour (71 g/day) compared to those fed diet containing unsoaked leaves and water soaked leaves (38.9 and 44.7 g/day, respectively) (P < 0.05). In the second digestibility experiment, the three diets were: (1) sugar cane tops: unsoaked Acacia (7:3), (2) sugar cane tops water soaked Acacia (7:3), (3) sugar cane tops: calcium hydroxide soaked Acacia (7:3). A supplement of 100 g/day of cassava flour was added to each of these three diets. In both digestibility experiments, soaking improved intake and digestibility of Acacia leaves, and cassava flour increased the intake, but when all the diets contained cassava flour, there was no significant difference (P > 0.05) found in intake or digestibility between unsoaked and soaked leaves. In conclusion, soaking reduced tannin in Acacia leaves, improved digestibility and intake of Acacia leaves. In the

  17. Cd immobilization in a contaminated rice paddy by inorganic stabilizers of calcium hydroxide and silicon slag and by organic stabilizer of biochar.

    Science.gov (United States)

    Bian, Rongjun; Li, Lianqing; Bao, Dandan; Zheng, Jinwei; Zhang, Xuhui; Zheng, Jufeng; Liu, Xiaoyu; Cheng, Kun; Pan, Genxing

    2016-05-01

    A field experiment was conducted in a Cd-contaminated rice paddy field to evaluate the effect of inorganic and organic metal stabilizers on Cd mobility and rice uptake. A dose of inorganic stabilizer of calcium hydroxide (CH), silicon slag (SS), and wheat straw biochar (BC) was amended respectively to topsoil before rice transplanting. Rice production was managed with the same water regime and fertilization practices consistently between treatments including a control without amendment. Samples of topsoil and rice plant were collected at rice harvest to analyze the Cd mobility and uptake by rice. Without affecting rice grain yield, the stabilizers significantly decreased CaCl2-extractable Cd in a range of 44 to 75 % compared to the control, corresponding to soil pH changes under the different treatments. Accordingly, Cd concentrations both in rice tissue and in rice grain were very significantly decreased under these treatments. The decrease in rice Cd uptake was correlated to the decrease in extractable Cd, which was again correlated to soil pH change under the different treatments, indicating a prevalent role of liming effect by the amendments. While applied at a large amount in a single year, organic stabilizer of BC decreased Cd extractability by up to 43 % and Cd rice uptake by up to 61 %, being the most effective on Cd immobilization. However, the long-term effect on soil health and potential tradeoff effects with different stabilizers deserve further field monitoring studies.

  18. Pulp response to high fluoride releasing glass ionomer, silver diamine fluoride, and calcium hydroxide used for indirect pulp treatment: An in-vivo comparative study

    Directory of Open Access Journals (Sweden)

    Atish Korwar

    2015-01-01

    Full Text Available Aims and Objectives: The study aims at determining pulp response of two high fluoride releasing materials silver diamine fluoride (SDF and Type VII glass ionomer cement (GIC when used as indirect pulp treatment (IPT materials. Materials and Methods: Deep Class V cavities were made on four first premolars indicated for extraction for orthodontic reasons. SDF, Type VII GIC, and calcium hydroxide base are given in three premolars, and one is kept control. Premolars were extracted 6 weeks after the procedure and subjected to histopathological examination to determine the pulp response. The results were analyzed using Chi-square test. Results: No inflammatory changes were observed in any of the groups. Significantly more number of specimens in SDF and Type VII GIC groups showed tertiary dentin deposition (TDD when compared to control group. No significant difference was seen in TDD when intergroup comparison was made. Odontoblasts were seen as short cuboidal cells with dense basophilic nucleus in SDF and Type VII GIC group. Conclusion: The study demonstrated TDD inducing ability of SDF and Type VII GIC and also established the biocompatibility when used as IPT materials.

  19. Clinical and radiographic assessment of mineral trioxide aggregate and calcium hydroxide as apexification agents in traumatized young permanent anterior teeth: A comparative study

    Science.gov (United States)

    Damle, S. G.; Bhattal, Hiteshwar; Damle, Dhanashree; Dhindsa, Abhishek; Loomba, Ashish; Singla, Sumit

    2016-01-01

    Background: To evaluate and compare the efficacy of mineral trioxide aggregate (MTA) and traditionally used calcium hydroxide (Ca(OH)2) in inducing root end formation of immature roots of traumatized young permanent anterior teeth. Materials and Methods: The study was carried out on 22 nonvital, immature permanent maxillary incisors. Samples were allotted into two groups - Group I MTA and Group II Ca(OH)2 Success rate was determined based upon the time duration required for apical barrier formation. The canals were obturated using gutta-percha points in MTA group, after 24 h, whereas in Ca(OH)2 group, obturation was carried out after radiographic confirmation of the apical barrier. The clinical and radiographic evaluation was carried out at a follow-up periods of 3, 6, and 9 months and statistical analysis was carried out by SPSS version 15.0 statistical analysis software (Chi-square test and fisher exact test). Results: In MTA Group, barrier formation was observed in 90.90% of the patients after 9 months whereas in Ca(OH)2 Group, the same was observed in 81.81%. The mean time required for barrier formation in MTA group was 4.90 months and 5.33 months in Ca(OH)2 group. Conclusion: MTA and Ca(OH)2, as medicaments for apexification, were comparable in terms of the evaluation parameters. However, MTA was beneficial in terms of immediate obturation of immature roots with wide open apices. PMID:27274351

  20. The enhancement effect of pre-reduction using zero-valent iron on the solidification of chromite ore processing residue by blast furnace slag and calcium hydroxide.

    Science.gov (United States)

    Li, Jinchunzi; Chen, Zhonglin; Shen, Jimin; Wang, Binyuan; Fan, Leitao

    2015-09-01

    A bench scale study was performed to assess the effectiveness of the solidification of chromite ore processing residue (COPR) by blast furnace slag and calcium hydroxide, and investigate the enhancement effect of pre-reduction using zero-valent iron (ZVI) on the solidification treatment. The degree of Cr immobilization was evaluated using the Toxicity Characteristic Leaching Procedure (TCLP) as well as the solid waste-extraction procedure for leaching toxicity-sulfuric acid & nitric acid method (Chinese standard HJ/T299-2007). Strength tests and semi-dynamic leaching tests were implemented to investigate the potential for reusing the final treatment product as a readily available construction material. The experimental results showed that the performance of pre-reduction/solidification (S/S) was superior to that of solidification alone. After pre-reduction, all of the S/S treated COPR samples met the TCLP limit for total Cr (5 mg L(-1)), whereas the samples with a COPR content below 40% met the pollution control limit of bricks and building block products (Chinese standard HJ/T 301-2007) produced with COPR for total Cr (0.3 mg L(-1)). At the same time, all of the S/S treated specimens tested were suitable for utilization at certain levels.

  1. Evaluation of a mixture of zinc oxide, calcium hydroxide, and sodium fluoride as a new root canal filling material for primary teeth

    Directory of Open Access Journals (Sweden)

    Chawla H

    2008-06-01

    Full Text Available Endodontic treatment was performed on 25 pulpally involved mandibular primary molars in 4 to 9-year-old children; the root canals were obturated with a new root canal filling material consisting of a mixture of calcium hydroxide, zinc oxide, and 10% sodium fluoride solution, using hand-operated lentulo-spirals. All cases were evaluated clinically every 3 months and also radiographically every 6 months to assess the success of the treatment; we also examined the resorption of the root canal filling material from the root canals and the status of overpushed material, if any, as the tooth resorbed with the passage of time. At 6 months, endodontic treatment in 2 of the 25 teeth had failed and one tooth had exfoliated; the remaining 22 teeth were without any signs or symptoms. At the end of 2 years, 14 teeth could be evaluated; out of these 12 had physiologically exfoliated. It was observed that the rate of resorption of this new root canal obturating mixture was quite similar to the rate of physiologic root resorption in primary teeth. In three cases, where there was an overpush of the mixture, a gradual partial resorption was noted.

  2. Comparison of calcium carbonate and aluminium hydroxide as phosphate binders on biochemical bone markers, PTH(1-84), and bone mineral content in dialysis patients

    DEFF Research Database (Denmark)

    Jespersen, B; Jensen, J D; Nielsen, H K;

    1991-01-01

    Bone mineral content, estimated by single-photon absorptiometry of the forearm, serum values of intact parathyroid hormone (PTH(1-84], osteocalcin, alkaline phosphatase, 1,25-dihydroxycholecalciferol (1,25(OH)2D3), and aluminium were determined during treatment with calcium carbonate (CaCO3...... 0.05), osteocalcin decreased (89% versus 117%, P less than 0.01), alkaline phosphatase decreased (92% versus 116%, P less than 0.05), and aluminium decreased (56% versus 189%, P less than 0.05). 1,25(OH)2D3 remained unchanged in both periods. No increase in soft-tissue calcification was demonstrated......) or aluminium hydroxide (Al(OH)3) in 11 dialysis patients participating in a randomised cross-over study. Each treatment period lasted 6 months. Serum phosphorus was maintained in the range 1.5-2.0 mmol/l. During Al(OH)3 treatment bone mineral content (BMC) decreased by 11% per half-year (mean), but only by 3...

  3. Effect of Calcium Hydroxide Based Intracanal Medicaments on the Apical Sealing Ability of Resin Based Sealer and Guttapercha Obturated Root Canals

    Science.gov (United States)

    Sumanthini, MV; Shenoy, Vanitha U; Bodhwani, Mohit A

    2017-01-01

    Introduction Calcium Hydroxide (CH) is one of the most commonly used intracanal medicaments which can be used with various vehicles. Aim The aim of this in vitro study was to evaluate the effect of three CH based intracanal medicaments on the apical sealing ability of AH Plus – guttapercha obturation. Materials and Methods Crowns of 100 extracted single rooted human teeth were sectioned at the Cemento-Enamel Junction (CEJ) to a standardized length. The root canals were instrumented upto ISO size 40 using step back technique and the specimens were randomly divided into two control and four experimental groups. The control groups were not medicated. Specimens in positive control group (Group I) were obturated with guttapercha without placing sealer and in negative control group (Group II) were obturated with guttapercha and AH Plus sealer. Among the experimental groups, specimens of Group III were not medicated while groups IV, V and VI were medicated with CH-saline, CH-2% Chlorhexidine (CHX) and Vitapex respectively for a period of 14 days. The medicaments were removed from the specimens and the teeth were obturated with AH Plus sealer and guttapercha using lateral compaction technique. The specimens were immersed in India ink dye, demineralized and diphanized. The extent of dye penetration was assessed using a 10X stereomicroscope. Data obtained was statistically analyzed by one-way ANOVA (p<0.05) followed by Post-hoc Tukey test. Results Amongst the three CH medicaments, CH-2% CHX when used as an intracanal medicament showed a significantly higher microleakage as compared to the other groups with p<0.001. The microleakage values between the remaining groups were not statistically significant. Conclusion Under the conditions of this study it was concluded that all groups with or without intracanal medicament showed apical leakage. The vehicle used to carry CH may significantly influence the apical sealing ability of guttapercha – AH Plus obturated canals. PMID

  4. Removal of calcium hydroxide from Weine Type II systems using photon-induced photoacoustic streaming, passive ultrasonic, and needle irrigation: a microcomputed tomography study

    Directory of Open Access Journals (Sweden)

    Adam LLOYD

    Full Text Available ABSTRACT Objective This study compared the effectiveness of Er:YAG laser-activated irrigation (PIPS, passive ultrasonic irrigation (PUI with EndoUltra and standard needle irrigation (SNI in the removal of calcium hydroxide [Ca(OH2] from the mesial roots of Weine Type II mandibular molars. Material and Methods Thirty mandibular molars were screened by µCT for the presence of mesial roots with complex intra-canal anatomy and a common apical foramen. The teeth were enlarged to a standardized 25/.06 preparation and filled with Ca(OH2 paste. Specimens were divided into three groups (n=10 according to the technique used for Ca(OH2 removal: PIPS, at 15 Hz and 20 mJ using a 9 mm long, 600 µm diameter tip; PUI using a 15/.02 tip; and SNI (30 Ga. side-vented needle. Equal volumes of 8.25% NaOCl and 17% EDTA were used in all groups. µCT was used to measure the initial amount of Ca(OH2 present and to assess the residual volume of Ca(OH2 following each irrigation protocol. Data were analyzed using Tukey HSD and Kruskal-Wallis tests (α=5%. Results The mean volume of Ca(OH2 before removal was significantly higher in the coronal third than in the middle and apical third (p0.05. PIPS (median 0%; IQR: 0-0 showed significant higher Ca(OH2 removal in the apical third than PUI (median 100%, IQR: 85-100 and SNI (median 47%; IQR: 16-72 (p<0.001. Conclusions PIPS laser-activation was more effective for the removal of Ca(OH2 from mesial roots of mandibular molars with Weine Type II canal configurations than PUI with EndoUltra and SNI.

  5. Comparative evaluation of platelet-rich fibrin, mineral trioxide aggregate, and calcium hydroxide as pulpotomy agents in permanent molars with irreversible pulpitis: A randomized controlled trial

    Directory of Open Access Journals (Sweden)

    Varun Kumar

    2016-01-01

    Full Text Available Background: Pulpotomy has been proposed as an alternative for the management of irreversible pulpitis in permanent molars with closed apices. Aim: To compare the performances of calcium hydroxide (CH, mineral trioxide aggregate (MTA, and platelet-rich fibrin (PRF as pulpotomy agents in mature permanent molars with irreversible pulpitis. Materials and Methods: Fifty-four permanent mandibular molars with carious exposure and symptoms of irreversible pulpitis were randomly allocated to three groups, and full pulpotomy was performed using CH,MTA, or PRF as pulpotomy agents. Pain intensity was recorded using numeric rating scale score at baseline, 24 h, 7 days, 6 months, and 1 year. Clinical and radiographic assessments were done at 6 months and 1 year. Statistical Analysis: Kruskal–Wallis test and Friedman test were used for intergroup and intragroup comparison of pain scores, respectively. The radiographic outcomes between the three study arms were compared using Chi-square test. Results: Clinical success rate was 94.4% at 7 days, which dropped to 85.4% at 12 months. All three agents were equally effective in providing pain relief at all the intervals tested, with no significant difference between them (P > 0.05 at all intervals. However, at 6 months and 12 months, 26.2% and 52.4% teeth depicted slight widening of periodontal ligament space. No significant difference was observed between the radiographic success rates observed with the three groups (P = 0.135 at 6 months, 0.717 at 12 months. Conclusion: Pulpotomy exhibited a high clinical success rate in mature molars with irreversible pulpitis and selection of biomaterial did not affect its outcome.

  6. Comparative evaluation of platelet-rich fibrin, mineral trioxide aggregate, and calcium hydroxide as pulpotomy agents in permanent molars with irreversible pulpitis: A randomized controlled trial

    Science.gov (United States)

    Kumar, Varun; Juneja, Ruchi; Duhan, Jigyasa; Sangwan, Pankaj; Tewari, Sanjay

    2016-01-01

    Background: Pulpotomy has been proposed as an alternative for the management of irreversible pulpitis in permanent molars with closed apices. Aim: To compare the performances of calcium hydroxide (CH), mineral trioxide aggregate (MTA), and platelet-rich fibrin (PRF) as pulpotomy agents in mature permanent molars with irreversible pulpitis. Materials and Methods: Fifty-four permanent mandibular molars with carious exposure and symptoms of irreversible pulpitis were randomly allocated to three groups, and full pulpotomy was performed using CH, MTA, or PRF as pulpotomy agents. Pain intensity was recorded using numeric rating scale score at baseline, 24 h, 7 days, 6 months, and 1 year. Clinical and radiographic assessments were done at 6 months and 1 year. Statistical Analysis: Kruskal–Wallis test and Friedman test were used for intergroup and intragroup comparison of pain scores, respectively. The radiographic outcomes between the three study arms were compared using Chi-square test. Results: Clinical success rate was 94.4% at 7 days, which dropped to 85.4% at 12 months. All three agents were equally effective in providing pain relief at all the intervals tested, with no significant difference between them (P > 0.05 at all intervals). However, at 6 months and 12 months, 26.2% and 52.4% teeth depicted slight widening of periodontal ligament space. No significant difference was observed between the radiographic success rates observed with the three groups (P = 0.135 at 6 months, 0.717 at 12 months). Conclusion: Pulpotomy exhibited a high clinical success rate in mature molars with irreversible pulpitis and selection of biomaterial did not affect its outcome. PMID:27994420

  7. Counteraction of reactive oxygen species and determination of antibacterial efficacy of proanthocyanidin and lycopene when mixed with calcium hydroxide and chlorhexidine mixture: An in vitro comparative study

    Directory of Open Access Journals (Sweden)

    T A Mageshwaran

    2012-01-01

    Full Text Available Aim: The objective of the study was to determine the neutralizing effect of proanthocyanidin (grape seed extract and lycopene (tomato extract on reactive oxygen species (ROS generated by the mixture when used as an intracanal medicament. The study also evaluated the effect of proanthocyanidin and lycopene on the antibacterial efficacy of a mixture of chlorhexidine (CHX and calcium hydroxide [Ca(OH 2 ] against Enterococcus feacalis. Materials and Methods: Four sample groups were prepared as follows. Group I: 2% CHX gluconate (control group and group II: a mixture of 125 mg of Ca(OH 2 with 2% CHX gluconate solution. Group III was a mixture of 125 mg of Ca(OH 2 with 1 mL of 2% CHX gluconate solution and 1 mL of 5% proanthocyanidin solution and group IV, a mixture of 125 mg of Ca(OH 2 with 1 mL of 2% CHX gluconate solution and 1 mL of 5% lycopene solution. The groups were analyzed for ROS formation using the mass spectrometer (JEOL GC MATE II immediately after preparation. The antibacterial property was evaluated by using agar diffusion method and the results were statistically analyzed using one-way analysis of variance (ANOVA and Tukey-Kramer multiple comparison tests. Results: The peak value of 196.96 denotes ROS formation. Group II shows a higher peak value than other groups. Group IV shows a drastic reduction in the peak value. Group IV shows a drastic reduction in ROS formation when compared with group II, group III, and the control group. Antibacterial efficacy was higher in group IV, followed by group III, group II, and group I. Conclusion: Lycopene and proanthocyanidin reduce the ROS significantly by virtue of their antioxidant property. Lycopene shows more antioxidant property when compared with proanthocyanidin.

  8. Pulpal responses to bacterial contamination following dentin bridging beneath hard-setting calcium hydroxide and self-etching adhesive resin system.

    Science.gov (United States)

    Kitasako, Yuichi; Ikeda, Masaomi; Tagami, Junji

    2008-04-01

    To evaluate the pulp healing to bacterial contamination beneath a hard-setting calcium hydroxide (DY: Dycal, L.D. Caulk Co.) and a self-etching adhesive resin (2V: Clearfil Liner Bond 2V, Kuraray Medical Inc.) following dentin bridge formation. Class V cavities were prepared on 30 monkey teeth, and the pulps were exposed with a carbide bur through the cavity floor. Each exposed pulp was capped with either DY or 2V. The cavities were restored with a hybrid resin composite. The resin composite was removed at 180 days after capping, and then cavities were left open to the oral environment for 2 weeks to obtain bacteria contamination DY (BDY) and 2V (B2V; n = 10). A non-bacterial-contaminated group capped with DY was used as control. After bacterial challenges, inflammatory cell infiltration, incidence and differentiation of dentin bridges were evaluated histologically. There were significant differences in the presence of inflammatory cell infiltration among all groups (P < 0.05). No moderate or severe inflammatory reaction was found in Group DY. Group BDY showed moderate or severe inflammatory cell infiltration in 50%, and showed four necrotic specimens. Although no statistically significant difference was found in the formation and differentiation of dentin bridges among all groups, tunnel defects in dentin bridges were detected in 70% (DY), 80% (BDY), and 50% (B2V). Group B2V showed a significantly lower presence of inflammatory cell infiltration than Group BDY (P < 0.05). Bonding agent is supposed to seal the exposure site, and the remaining bonding agent on the cavities was effective as the barrier in the dentin bridges after bacterial challenges.

  9. Comparison of calcium hydroxide removal by self-adjusting file, EndoVac, and CanalBrush agitation techniques: An in vitro study

    Directory of Open Access Journals (Sweden)

    Sevinç Aktemur Türker

    2013-01-01

    Full Text Available Objectives: This study comparatively evaluated the efficacy of self-adjusting file (SAF, Endovac, and CanalBrush irrigant agitation protocols in removing calcium hydroxide (Ca(OH 2 from the root canals. Materials and Methods: Sixty extracted human mandibular canine teeth were instrumented with ProTaper rotary instruments to size #40 and dressed with Ca(OH 2 . The roots were randomly assigned to four groups according to irrigant agitation protocol used (n = 15. In Group 1: Conventional syringe irrigation (no activation, control; Group 2: Rotary brush agitation (CanalBrush; Group 3: Apical negative pressure irrigation (EndoVac system; and Group 4: Sonic agitation (SAF were used. Scanning electron microscopic (SEM evaluation was done for assessment of Ca(OH 2 removal in the coronal and apical thirds. Statistical analysis was performed by Wilcoxon and Kruskal-Wallis tests. Results: There were statistically significant differences among the groups (P = 0.218. A statistically significant difference was seen between the test groups in Ca(OH 2 removal from the apical third of the canal (P 0.05. The most efficient Ca(OH 2 removal in apical third was recorded in Group 3 (EndoVac and Group 4 (SAF (P < 0.05. In Group 4 (sonic agitation, there was no significantly difference between Ca(OH 2 removal in coronal and apical thirds. Conclusions: SAF and EndoVac showed significantly better performance than CanalBrush and conventional syringe irrigation in removing Ca(OH 2 from apical third of the root canals.

  10. Quantitative comparison of calcium hydroxide removal by EndoActivator, ultrasonic and ProTaper file agitation techniques: an in vitro study.

    Science.gov (United States)

    Khaleel, Huda Yasir; Al-Ashaw, Ahmed Jawad; Yang, Yan; Pang, Ai-hui; Ma, Jing-zhi

    2013-02-01

    Calcium hydroxide (CH) dressing residues can compromise endodontic sealing. This study aimed to evaluate the amount of remaining CH in root canals after mechanical removal by four groups of irrigation techniques including needle irrigation only, ProTaper file, EndoActivator, and ultrasonic file. Fifteen extracted single-rooted teeth were collected and used for all four groups. The samples were firstly prepared by ProTaper rotary instruments, and then sectioned longitudinally through the long axis of the root canals, followed by final reassembling by wires. CH was kept in the canals for 7 days setting. The removal procedure began with 5 mL of 2.5% sodium hypochlorite (NaOCl) followed by 1 mL of 17% ethylenediaminetetraacetic acid and a final irrigation with 5 mL of 2.5% NaOCl solution for all groups. No additional agitation of the irrigant was performed in group 1, while agitation for 20 s between irrigants was done with F2 ProTaper rotary file in group 2, EndoActivator with tip size 25/.04 in group 3 and by an ultrasonic file 25/.02 in group 4. The total activation time was 60 s. The roots were then disassembled and captured by digital camera. The ratio of CH coated surface area to the surface area of the whole canal as well as each third of the canal was calculated. The data were statistically analyzed by one-way ANOVA using post hoc Tukey test. Results showed that none of the four techniques could remove all CH. No significant difference was found between EndoActivator and ultrasonic techniques. However, they both removed significantly more CH than ProTaper and needle irrigation (P=0.0001). In conclusion, the sonic and ultrasonic agitation techniques were more effective in removing intracanal medicaments than the ProTaper rotary file and needle irrigation in all thirds of the canal.

  11. Early age hydration of calcium sulfoaluminate (synthetic ye'elimite, C{sub 4}A{sub 3}S{sup ¯}) in the presence of gypsum and varying amounts of calcium hydroxide

    Energy Technology Data Exchange (ETDEWEB)

    Hargis, Craig W. [Department of Civil and Environmental Engineering, University of California, Berkeley, CA (United States); Kirchheim, Ana Paula [Department of Civil Engineering, Federal University of Rio Grande do Sul, Porto Alegre, RS (Brazil); Monteiro, Paulo J.M., E-mail: monteiro@ce.berkeley.edu [Department of Civil and Environmental Engineering, University of California, Berkeley, CA (United States); Gartner, Ellis M. [Lafarge Centre de Recherche, St. Quentin Fallavier, Isere (France)

    2013-06-15

    Suspensions of synthetic ye'elimite (C{sub 4}A{sub 3}S{sup ¯}) in a saturated gypsum (CS{sup ¯}H{sub 2}) and calcium hydroxide (CH) solution were examined in-situ in a wet cell by soft X-ray transmission microscopy and ex-situ by scanning electron microscopy. The most voluminous hydration product observed was ettringite. Ettringite commonly displayed acicular, filiform, reticulated, and stellate crystal habits. Additionally, pastes with C{sub 4}A{sub 3}S{sup ¯}, 15% CS{sup ¯}H{sub 2}, and varying amounts of CH were prepared and examined with X-ray diffraction (XRD) and isothermal calorimetry. The XRD experiments showed that increasing CH content caused more solid solution (SO{sub 4}{sup 2−}/OH{sup −}) AFm phases to form at early ages (< 1 d) and more monosulfate to form at later ages (> 1 d). Calorimetry indicated that the increased production of solid solution AFm was accompanied with an increase in the initial (< 30 min) rate of heat evolution, and increasing CH generally reduced the time till the second maximum rate of heat evolution due to the formation of ettringite and monosulfate.

  12. 21 CFR 184.1191 - Calcium carbonate.

    Science.gov (United States)

    2010-04-01

    ... HUMAN CONSUMPTION (CONTINUED) DIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of... soda process”; (2) By precipitation of calcium carbonate from calcium hydroxide in the...

  13. The effectiveness of various chelates used alone or in combination with sodium hypochlorite in the removal of calcium hydroxide from root canals

    Directory of Open Access Journals (Sweden)

    Emel Uzunoglu

    2015-01-01

    Full Text Available Aim: To evaluate the effectiveness of various chelates used alone or in combination with sodium hypochlorite (NaOCl in the removal of calcium hydroxide (Ca(OH2 from root canals. Materials and Methods: The root canals of 72 mandibular incisors were prepared up to the ProTaper F2 file. Among these, six randomly selected teeth were used as negative and positive controls, while the root canals of the remaining 66 were filled with Ca(OH2 paste for 1 week. Then, the experimental group specimens were divided into six groups (n = 11. The access cavities were reopened and the Ca(OH2 paste in each group was removed using the following solutions: 2.5 mL ethylenediaminetetraacetic acid (EDTA; Group 1, 2.5 mL peracetic acid (PAA; Group 2, 2.5 mL QMix (Group 3, 2.5 mL NaOCl/2.5 mL EDTA (Group 4, 2.5 mL NaOCl/2.5 mL PAA (Group 5, and 2.5 mL NaOCl/2.5 mL QMix (Group 6. Digital photographs of longitudinally split specimens were imported into image analyzer software, and the amount of residual Ca (OH 2 was recorded as a percentage of the overall canal surface area. The results were analyzed using Kruskal–Wallis and Conover–Dunn tests. Results: The canal walls in the positive control group were completely covered with Ca(OH 2 compared with those in the negative control group. The lowest Ca(OH2 removal efficiency was observed for Group 4 (P < 0.001, while Group 6 showed favorable results (P < 0.05. Conclusions: QMix combined with NaOCl can remove Ca(OH2 from root canals as effectively as 17% EDTA and 1% PAA. The type and sequence of irrigants are more important than the total irrigant volume for effective Ca(OH 2 removal.

  14. Clinical application of light curing calcium hydroxide in primary teeth pulpotomy surgery%光固化氢氧化钙在乳牙牙髓切断术中的临床应用

    Institute of Scientific and Technical Information of China (English)

    陈虹; 席微; 来洁

    2016-01-01

    目的:探讨适合乳牙牙髓炎的早期最简单、有效的治疗方法。方法:收治乳牙牙髓炎早期患儿196例,应用光固化氢氧化钙行乳牙牙髓切断术,观察效果。结果:196例患者中,177例取得成功,成功率90.75%。结论:乳牙牙髓炎早期患儿应用光固化氢氧化钙行乳牙牙髓切断术,是一种简单有效的治疗方法。%Objective:To investigate the most simple and effective treatment methods for primary teeth pulpitis.Methods:196 cases of children with early primary teeth pulpitis were selected.They were treated with light curing calcium hydroxide for primary teeth pulpotomy.We observed the effect.Results:In the 196 patients,177 cases were successful,and the success rate was 90.75% . Conclusion:The application of light curing calcium hydroxide in primary teeth pulpotomy surgery for children with early primary teeth pulpitis was a simple and effective treatment.

  15. Surface tension of calcium hydroxide associated with different substances Tensão superficial do hidróxido de cálcio associado a diferentes substâncias

    Directory of Open Access Journals (Sweden)

    Carlos Estrela

    2005-06-01

    Full Text Available The purpose of this study was to evaluate the surface tension of calcium hydroxide (CH associated with different substances (deionized distilled water, camphorated paramonochlorophenol, 2% chlorhexidine digluconate, Otosporin, 3% sodium lauryl ether sulphate; Furacin, PMC Furacin using tensiometer. The action of the substances studied on the dentinal structure enhances the property of surface tension. This method consists in the application of force to separate a platinum ring immersed in the substances. Thus, torsion was applied to the screw until the platinum ring separated during substances testing. Considering the methodology applied, the following can be concluded: distilled water alone or associated with CH presented a high surface tension (70.00 and 68.40 dynes/cm; calcium hydroxide in association with anionic detergent showed low surface tension (31.60 dynes/cm; camphorated paramonochlorophenol plus CH presented low surface tension (37.50 dynes/cm; 2% chlorhexidine associated with calcium hydroxide showed high surface tension values (58.00 dynes/cm; Otosporin plus calcium hydroxide showed low surface tension (35.40 dynes/cm; paramonochlorophenol Furacin mixed with calcium hydroxide presented surface tension equal to 45.50 dynes/cm; sodium hypochlorite presented high surface tension (75.00 dynes/cm. Antimicrobial agents more indicated in endodontics, i.e. CH, chlorhexidine and hypochlorite, presented the highest surface tension.Estudou-se a tensão superficial do hidróxido de cálcio associado a diferentes substâncias (água destilada deionizada, paramonoclorofenol canforado, digluconato de clorexidina 2%, Otosporin, sulfato éter lauril sódio 3%, furacin, PMC furacin usando tensiômetro. O modelo experimental consistiu na aplicação de uma força para separar um anel de platina imerso na superfície das substâncias, exercido por um tensiômetro. Considerando a metodologia aplicada, pode-se concluir: a água destilada isolada ou

  16. Iodine Glycerin plus Calcium Hydroxide for treatment pericoronitis%应用氢氧化钙碘甘油糊剂治疗智齿冠周炎的疗效观察

    Institute of Scientific and Technical Information of China (English)

    陈福稳

    2013-01-01

      Objective: To evaluate calcium hydroxide paste iodine glycerin treatment pericoronitis clinical results. Methods: randomly selected hospital dental clinic from October 2010 to October 2012 were treated 214 cases of pericoronitis patients and divided into two groups, namely the treatment and control groups. Patients treated with calcium hydroxide paste iodine glycerin treatment. Control group patients with iodine glycerin treatment. 3 days after treatment, the therapeutic effect of two groups were compared. Results: 3 days after treatment, patients treated with the treatment efficiency than the control group patients, and the differences between the two groups was statistically significant (P<0.05). Conclusion:Compared with the application of iodine glycerin, application of calcium hydroxide paste iodine glycerin pericoronitis treatment efficacy more reliable.%  目的:探讨应用氢氧化钙碘甘油糊剂治疗智齿冠周炎的临床效果。方法:随机选取我院口腔门诊2010年10月至2012年10月间收治的214例智齿冠周炎患者作为研究对象并将其分为两组,即治疗组和对照组。治疗组患者应用氢氧化钙碘甘油糊剂进行治疗。对照组患者应用碘甘油进行治疗。治疗3天后,比较两组患者的治疗效果。结果:治疗3天后,治疗组患者治疗的有效率优于对照组患者,且两组间的差异具有统计学意义(P<0.05)。结论:与应用碘甘油相比,应用氢氧化钙碘甘油糊剂治疗智齿冠周炎的疗效更佳、操作更简便。

  17. 氢氧化钙在年轻恒牙牙髓治疗中的疗效探析%Efficacy of Calcium Hydroxide in Endodontic Therapy for Immature Per-manent Teeth

    Institute of Scientific and Technical Information of China (English)

    宋林操

    2015-01-01

    目的:探析氢氧化钙在年轻恒牙牙髓治疗中的疗效。方法整群选取2012年1月-2015年6月该院收治的52例(54颗)第一磨牙牙髓炎和根尖周炎年轻恒牙患者作为研究对象,均给予氢氧化钙进行牙髓治疗,对其临床治疗效果进行分析。结果21颗深龋导致的意外穿髓采用盖髓术和活髓切断术进行治疗后,成功19颗,成功率为90.5%,33颗牙髓炎和根尖周炎采用根管治疗后成功30颗,成功率为(90.9%)。结论氢氧化钙在年轻恒牙牙髓治疗中的疗效确切,安全可靠,值得临床选择和积极推广使用。%Objective To analyze the efficacy of calcium hydroxide in endodontic therapy for immature permanent teeth. Methods 52 patients (54 teeth) with immature permanent teeth suffering from pulpitis and periapical periodontitis in first molar teeth admitted to our hospital from January 2012 and June 2015 were included in this study and given endodontic therapy using calcium hydroxide. The clinical efficacy was analyzed. Results 21 teeth of unexpected pulp canalization in deep dental caries were treated by pulp capping and pulpotomy and 19 were treated successfully with a success rate of 90.5%. 33 teeth of pulpitis and periapical periodontitis were treated by root canal therapy and 30 were treated successfully with a success rate of 90.9%. Conclusion Calcium hydroxide in endodontic therapy for immature permanent teeth has exact efficacy and is safe and reliable, therefore this method is worthy of application and active promotion in clinical practice.

  18. The disinfection effect of calcium hydroxides dressing using different vehicles on clinical root canal treatment%不同赋形剂氢氧化钙根管消毒效果的临床研究

    Institute of Scientific and Technical Information of China (English)

    付国祥; 骆鸣宇; 高倩华; 廖雪峰; 王瑛

    2012-01-01

    目的 比较生理盐水、碘甘油、樟脑对氯苯酚、樟脑对氯苯酚/碘甘油等赋形剂对氢氧化钙消毒根管效果的影响,以期为临床工作提供参考.方法 选择单根管慢性根尖周炎患牙80颗,随机分成氢氧化钙加生理盐水、氢氧化钙加碘甘油、氢氧化钙加樟脑对氯苯酚、氢氧化钙加樟脑对氯苯酚/碘甘油等4组,观察封药1周后的临床疗效、封药1周前后的细菌学培养菌落数变化以及达到临床可充填的封药时间等评价指标.结果 氢氧化钙加樟脑对氯苯酚/碘甘油组明显优于氢氧化钙加生理盐水、氢氧化钙加碘甘油、氢氧化钙加樟脑对氯苯酚组(P<0.01);在封药1周的临床疗效(评分差值)方面,氢氧化钙加生理盐水组、氢氧化钙加樟脑对氯苯酚组差异无统计学意义(P>0.05);在达到临床可充填封药时间上,氢氧化钙加碘甘油组、氢氧化钙加樟脑对氯苯酚组差异无统计学意义(P>0.05).结论 在生理盐水、碘甘油、樟脑对氯苯酚、樟脑对氯苯酚/碘甘油等赋形剂中,樟脑对氯苯酚/碘甘油可能是最为有效的赋形剂.%Objective To investigate the clinical effect of root canal disinfection with calcium hydroxides dressing respectively in four different vehicles (physiological saline, iodine glycerin, camphorated para-monochlorophenol and camphorated para-monochlorophenol/iodine glycerin), in order to provide reference for clinical root canal treatment. Methods To divide 80 teeth of single-root canal teeth having chronic apical periodontitis randomly into four groups according to the vehicles (physiological saline, iodine glycerin, camphorated para-monochlorophenol and camphorated para-monochlorophenol/iodine glycerin), observing the clinical effect after 7 days, bacterial colony numbers of root canal contents before and 7 days after calcium hydroxides dressing, clinical duration of root canal treatment. Results The camphorated para

  19. 稀硫酸-氢氧化钙联合预处理玉米秸秆制乙醇%Ethanol Production from Dilute Sulfuric Acid-calcium Hydroxide Co-pretreated Corn Stover

    Institute of Scientific and Technical Information of China (English)

    朱圆圆; 杨金龙; 朱均均; 张璐; 徐勇; 勇强; 余世袁

    2015-01-01

    以玉米秸秆为原料,研究稀硫酸-氢氧化钙联合预处理秸秆制备燃料乙醇的方法. 玉米秸秆经稀硫酸预处理、固液分离后得到的预水解液(主要含有木糖)进行戊糖发酵;而残渣采用氢氧化钙进一步预处理后,经酶水解得到的葡萄糖进行己糖发酵,从而实现戊糖和己糖分开发酵产乙醇. 研究结果表明,玉米秸秆稀硫酸预处理最佳条件为:硫酸用量1. 00%(以绝干玉米秸秆计),反应温度130℃,反应时间70 min,此时木聚糖水解得率为80. 45%;采用树干毕赤酵母对玉米秸秆稀硫酸预水解液原液、浓缩液Ⅰ(浓度为原液的2 倍)和浓缩液Ⅱ(浓度为原液的3. 5 倍)进行戊糖发酵,乙醇得率分别为82. 52%、85. 13%和73. 64%. 氢氧化钙进一步预处理玉米秸秆稀硫酸预处理渣的最佳条件为:氢氧化钙用量0. 125 g/g(以绝干玉米秸秆计),反应温度90 ℃,时间24 h,此时纤维素酶水解得率为84. 92%;采用酿酒酵母对两步预处理残渣的酶水解液原液、浓缩液Ⅲ和浓缩液Ⅳ(浓度为原液的2倍和3倍)进行己糖发酵,乙醇得率分别为92. 22%、91. 89%和85. 54%.%Corn stover pretreated by dilute sulfuric acid and calcium hydroxide was used to produce fuel ethanol. The pre-hydrolyzate obtained from dilute sulfuric acid pretreated corn stover was mainly composed by xylose,which could be fermented to produce ethanol. The solid residue were further pretreated by calcium hydroxide and then hydrolyzated to glucose with cellulase for hexose fermentation. Based on this process, the glucose and xylose could be converted to ethanol,respectively. The optimal dilute sulfuric acid pretreatment could be obtained as the corn stover was pretreated by 1. 00% sulfuric acid ( based on dry corn stover),rat 130 ℃ for 70 min and the xylan hydrolysis yield was 80. 45%. The ethanol yields of pentose fermentation of the unconcentrated,1-fold concentrated and 2. 5-folds concentrated pre-hydrolyzates by

  20. Evaluation of a consolidation treatment in dolostones by mean of calcium hydroxide nanoparticles in high relative humidity conditions; Evaluacion del tratamiento de consolidacion de dolomias mediante nanoparticulas de hidroxido de calcio en condiciones de alta humedad relativa

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Villalba, L. s.; Lopez-Arce, P.; Zornoza, A.; Alvares de Buergo, M.; Fort, R.

    2011-07-01

    In this article, the results of a treatment applied to dolomitic stones using an isopropyl colloidal solution based on calcium hydroxide nanoparticles with a concentration of 2.0g/l are presented. The consolidation process in the stone has been checked before and after 28 days of exposure to 75% relative humidity. Morphologic and structural studies of the consolidating product confirmed the carbonation process. X ray diffraction, electron microscopy (TEM and ESEM), and electron diffraction carried out on the consolidating product have confirmed the transformation of portlandite phase to calcium carbonate polymorph, calcite, aragonite and vaterite. Petrophysical tests performed on the stone before and after the application of the product have shown the improvement in the physical and hydrical properties due to the increase in the ultrasound velocity and density of the material, and a decrease in the capillarity coefficient and open porosity without significant changes in colour and brightness. The application of the consolidating product in the proposed experimental conditions is a natural method, compatible with the petrological characteristics of the substrate, without secondary damages on the stone, being an effective method to improve the durability of carbonate stones. (Author) 26 refs.

  1. Histologic evaluation of pulpotomy performed with ethyl-cyanoacrylate and calcium hydroxide Avaliação histológica de pulpotomia realizada com etil-cianoacrilato e com hidróxido de cálcio

    Directory of Open Access Journals (Sweden)

    Diana Santana de Albuquerque

    2006-09-01

    Full Text Available The aim of this study was to evaluate histological aspects of the pulp-dentin complex of dogs submitted to pulpotomy and capped with ethyl-cyanoacrylate and calcium hydroxide. Thirty dog teeth were divided into 2 groups of 15 as follows: Group 1 - ethyl-cyanoacrylate; Group 2 - calcium hydroxide. The pulpotomies were carried out following all of the treatment precautions recommended for dogs. After 30 days the specimens were submitted to histological preparation and were then blindly evaluated by a histologist. Data were analyzed statistically by the Fisher exact test, comparing the two groups. After 30 days, the presence of a hard tissue barrier was observed in 83.3% of Group 1, and in 100% of Group 2 (p = 0.478. A continuous hard tissue barrier was observed in 50% of the ethyl-cyanoacrylate group and 75% of the calcium hydroxide group (p = 0.652. It can be concluded that both materials induced hard tissue barrier formation, but Group 2 had a higher percentage than Group 1, with no significant statistical differences; the differences observed between the different barriers (continuous/non-continuous were not significant between groups and there was no pulpal necrosis in either group.O objetivo do presente estudo foi avaliar o aspecto histológico do complexo dentino-pulpar de cachorros quando capeado após a pulpotomia com etil-cianoacrilato e hidróxido de cálcio. Trinta dentes de cães foram divididos em 2 grupos de 15 da seguinte forma: Grupo 1 - Etil-cianoacrilato; Grupo 2 - Hidróxido de cálcio. A pesquisa foi realizada tomando-se todos os cuidados recomendados para o tratamento com os cães. Após 30 dias do procedimento realizado os espécimes foram submetidos ao preparo histológico e logo após foram avaliados de forma cega por um histologista. Os resultados foram analisados estatisticamente através do Teste Exato de Fisher. No grupo 1, 83,3% e no grupo 2, 100% dos dentes apresentaram a barreira de tecido duro (p = 0,478. A barreira

  2. Effect of pH and Calcium on the Adsorptive Removal of Cadmium and Copper by Iron Oxide–Coated Sand and Granular Ferric Hydroxide

    KAUST Repository

    Uwamariya, V.

    2015-08-17

    Iron oxide-coated sand (IOCS) and granular ferric hydroxide (GFH) were used to study the effect of Ca2+ and pH on the adsorptive removal of Cu2+ and Cd2+ from groundwater using batch adsorption experiments and kinetic modeling. It was observed that Cu2+ and Cd2+ were not stable in synthetic waters. The extent of precipitation increased with increasing pH. Removal of Cu2+ and Cd2+ was achieved through both precipitation and adsorption, with IOCS showing higher adsorption efficiency. Increase of pH (from 6 to 8) resulted in a higher overall removal efficiency of both Cu2+ and Cd2+, with precipitation as predominant removal mechanisms at higher pH values, especially for Cu2+. An increase in Ca2+ concentration increased the precipitation of Cu2+ [as Cu2(OH)2CO3 and Cu3(OH)2(CO3)2] and Cd2+ [as Cd(OH)2 and CdCO3]. In addition, Ca2+ competes with Cu2+ and Cd2+ for surface adsorption sites on IOCS and GFH, and reduces their adsorption capacity. The kinetic modeling revealed that the adsorption of Cd2+ onto IOCS is a complex process, with limited contribution of chemisorption that increases in the presence of Ca2+. © 2015 American Society of Civil Engineers.

  3. Sodium hydroxide poisoning

    Science.gov (United States)

    Sodium hydroxide is a very strong chemical. It is also known as lye and caustic soda. This ... poisoning from touching, breathing in (inhaling), or swallowing sodium hydroxide. This article is for information only. Do ...

  4. 氧化锌丁香油和氢氧化钙碘仿糊剂在乳牙根管充填中的疗效观察%Comparative study on zinc oxide eugenol and calcium hydroxide iodoform pastes as obturation materials for primary teeth

    Institute of Scientific and Technical Information of China (English)

    万惠; 符方满; 庞红霞; 符起亚

    2013-01-01

    目的 评估氧化锌丁香油和氢氧化钙碘仿糊剂作为乳牙根管充填材料的治疗效果.方法 将54颗下颌乳磨牙随机分为两组,其中27 颗接受氧化锌丁香油糊剂根管充填,27 颗接受氢氧化钙碘仿糊剂根管充填.在治疗后6 个月时用临床和影像指标评估治疗效果.结果 氧化锌丁香油和氢氧化钙碘仿糊剂根管充填后在临床和愈合指标方面差异无统计学意义(P>0.05),但超充后的氢氧化钙碘仿糊剂似乎比超充的氧化锌丁香油糊剂更容易吸收.结论 氧化锌丁香油和氢氧化钙碘仿糊剂在促进根尖愈合方面均为较好的根管充填材料,但若考虑到超充后材料的吸收,后者似乎更安全一些.%Objective To evaluate zinc oxide eugenol and calcium hydroxide iodoform as root canal obturation materials for primary teeth. Methods The canals of twenty-seven primary mandibular molars were obturated with zinc oxide eugenol and those of the other twenty-seven were obturated with calcium hydroxide iodoform. A set of clinical and radiological criteria was used to evaluate treatment outcomes at the completion of treatment and six months after treatment. Results No difference in terms of success rate 6 months after treatment was found between canals obturated with zinc oxide eugenol and those obturated with calcium hydroxide iodoform. In cases of overfill, calcium hydroxide iodoform seemed to be absorbed than zinc oxide eugenol. Conclusion Both zinc oxide eugenol and calcium hydroxide iodoform are good obturating materials. However, the latter may be a better choice where overfills are concerned.

  5. A study of the time necessary for calcium hydroxide to eliminate microorganisms in infected canals Estudo do tempo necessário para o hidróxido de cálcio eliminar microrganismos em canais infectados

    Directory of Open Access Journals (Sweden)

    Carlos Estrela

    2003-06-01

    Full Text Available The objective of this study was to analyze the time necessary for calcium hydroxide to eliminate microorganisms in infected canals. A total of 168 human anterior teeth were prepared and sterilized. One hundred sixty two teeth were inoculated with suspensions of S. aureus, E. faecalis, P. aeruginosa, B. subtilis, C. albicans. Three teeth were used as negative control and three as positive control. Root canals were irrigated with saline and filled with calcium hydroxide paste (CHP. At intervals of 1 minute, and at 7, 15, 21, 27, 30, 45, 60, and 90 days, CHP was removed, samples were collected and immersed in Letheen Broth (LB. Microbial growth was analyzed by two methods, turbidity of the culture medium and subculture on a Brain heart Infusion. After looking for medium change, an inoculum of 0.1 mL obtained from LB was transferred to 7 mL of Brain Heart Infusion (BHI, and subsequently incubated at 37°C for 48 hours. Microbial growth was checked by turbidity of the culture medium and in some cases by Gram stain. All assays were carried out in triplicate under aseptic technique. The results indicated that the antimicrobial effect on the cultures of S. aureus, E. faecalis, P. aeruginosa, B. subtilis, C. albicans and one mixed culture in infected canals by CHP occurred in 60 days.O objetivo deste estudo foi analisar o tempo necessário para que o hidróxido de cálcio elimine microrganismos em canais infectados. Um total de 168 dentes humanos anteriores foram preparados e esterilizados. Cento e sessenta e dois dentes foram inoculados com suspensões de S. aureus, E. faecalis, P. aeruginosa, B. subtilis e C. albicans. Três dentes foram usados como controle negativo e três como controle positivo. Os canais radiculares foram irrigados com solução fisiológica e preenchidos com pasta de hidróxido de cálcio. Em intervalos de 1 minuto, 7, 15, 21, 27, 30, 45, 60 e 90 dias, a pasta foi removida, amostras foram coletadas e imersas em Letheen Broth. O

  6. Role of oxidative stress and intracellular calcium in nickel carbonate hydroxide-induced sister-chromatid exchange, and alterations in replication index and mitotic index in cultured human peripheral blood lymphocytes

    Energy Technology Data Exchange (ETDEWEB)

    M' Bemba-Meka, Prosper [Universite de Montreal, Human Toxicology Research Group (TOXHUM), Department of Environmental and Occupational Health, Main Station, P.O. Box 6128, Montreal, QC (Canada); University of Louisville, Department of Pharmacology and Toxicology, Center for Genetics and Molecular Medicine, Louisville, KY (United States); Lemieux, Nicole [Universite de Montreal, Department of Pathology and Cellular Biology, Faculty of Medicine, Main Station, P.O. Box 6128, Montreal, QC (Canada); Chakrabarti, Saroj K. [Universite de Montreal, Human Toxicology Research Group (TOXHUM), Department of Environmental and Occupational Health, Main Station, P.O. Box 6128, Montreal, QC (Canada)

    2007-02-15

    Human peripheral lymphocytes from whole blood cultures were exposed to either soluble form of nickel carbonate hydroxide (NiCH) (0-60 {mu}M), or of nickel subsulfide (Ni{sub 3}S{sub 2}) (0-120 {mu}M), or of nickel oxide (NiO) (0-120 {mu}M), or nickel sulfate (NiSO{sub 4}) (0-120 {mu}M) for a short duration of 2 h. The treatments occurred 46 h after the beginning of the cultures. The cultures were harvested after a total incubation of 72 h, and sister-chromatid exchange (SCE), replication index (RI), and mitotic index (MI) were measured for each nickel compound. The soluble form of NiCH at 30 {mu}M but those of Ni{sub 3}S{sub 2} and NiO at 120 {mu}M produced significant increase in the SCE per cell compared to the control value, whereas NiSO{sub 4} failed to produce any such significant increase. Except NiSO{sub 4}, the soluble forms of NiCH, Ni{sub 3}S{sub 2}, and NiO produced significant cell-cycle delay (as measured by the inhibition of RI) as well as significant inhibition of the MI at respective similar concentrations as mentioned above. Pretreatment of human blood lymphocytes with catalase (H{sub 2}O{sub 2} scavenger), or superoxide dismutase (superoxide anion scavenger), or dimethylthiourea (hydroxyl radical scavenger), or deferoxamine (iron chelator), or N-acetylcysteine (general antioxidant) inhibited NiCH-induced SCE, and changes in RI and MI. This suggests the participation of oxidative stress involving H{sub 2}O{sub 2}, the superoxide anion radical, the hydroxyl radical, and iron in the NiCH-induced genotoxic responses. Cotreatment of NiCH with either verapamil (inhibitor of intracellular calcium ion ([Ca{sup 2+}]{sub i}) movement through plasma membranes), or dantrolene (inhibitor of [Ca{sup 2+}]{sub i} release from sarcoplasmic reticulum), or BAPTA (Ca{sup 2+} chelator) also inhibited the NiCH-induced responses. These results suggest that [Ca{sup 2+}]{sub i} is also implicated in the genotoxicity of NiCH. Overall these data indicate that various types

  7. EFFICACY ANALYSIS OF ANTIBIOTIC REAGENT AND CALCIUM HYDROXIDE IODOFORM PASTE GLYCERIN MAXIMUM IN APEXIFICATION%抗生素糊剂和氢氧化钙碘仿甘油糊剂在根尖诱导成形术中的疗效分析

    Institute of Scientific and Technical Information of China (English)

    魏东义; 张晨光; 鲁广建

    2012-01-01

    [目的]观察比较抗生素糊剂和氢氧化钙碘仿甘油糊剂在根尖诱导成形术中的临床疗效.[方法]选2007年1月~2008年6月期间行根尖诱导形成术的年轻恒牙224颗,随机分为两组,分别填充抗生素糊剂和氢氧化钙碘仿甘油糊剂,诱导根尖形成,随访3年,比较两组的临床疗效.[结果]抗生素糊剂组总有效率为85.7%,氢氧化钙碘仿甘油糊剂组总有效率为88.4%;两种糊剂不同牙根尖孔分型比较,同组内根端喇叭型分别与管壁平行型和管壁内聚型比较差异均有统计学意义(P<0.05),且管壁平行型及管壁内聚型的疗效均优于根端喇叭型疗效;两种糊剂各组间不同疾病比较,牙根尖周炎组抗生素糊剂疗效优于氢氧化钙碘仿甘油糊剂组(P<005).[结论]抗生素糊剂和氢氧化钙碘仿甘油糊剂均是比较理想的根尖诱导制剂,氢氧化钙碘仿甘油糊剂临床应用时要注意适应证的选择.%[Objective] To evaluate the efficacy of Antibiotic reagent and calcium hydroxide iodoform paste glycerin maximum in Apexification. [Methods] A prospective and retrospective study was carried out to investigate the permanent teeth among 224 patients with apexification during the period from January 2007 to June 2008. They were randomly divided into two groups, filling Antibiotic reagent and calcium hydroxide iodoform paste glycerin maximum, and Follow-up of 3 years. [Re-Slllts] The total effectiveness of antibiotic reagent group was 85.7%, and the total effectiveness of glycerin calcium hydroxide iodoform paste group was 88.4%. For the different paste rool tip hole model more points, there was statistically significant in the root hom with the wall and wall type parallel cohesion model (P < 0.05). For the different disease between different paste, root lip perisplenitis group paste curative effect was better than antibiotics calcium hydroxide iodoform paste glycerin group (P < 0.05). [Conclusion] Antibiotic

  8. The Clinical Effect Assessment of Jinhoujian Spry Mixing Calcium Hydroxide Paste for Chronic Periapical Periodontitis%金喉健喷雾剂混合氢氧化钙糊剂用于慢性根尖周炎的临床疗效评价

    Institute of Scientific and Technical Information of China (English)

    曾莲; 杨艳玲; 吉宁

    2011-01-01

    目的 评价金喉健喷雾剂混合氢氧化钙糊剂用于慢性根尖周炎的临床疗效.方法 选择慢性根尖周炎的患牙196颗,随机分为两组,常规根管预备后,实验组根管内封入金喉健喷雾剂混合氢氧化钙糊剂,对照组根管内封入氢氧化钙糊剂,封药2~4周后评价疗效.结果 实验组与对照组相比,实验组有效率91.0%,明显高于对照组81.21%.实验组封药无效率为9.0%,明显低于对照组的19.79%(P< 0.05).结论 金喉健喷雾剂混合氢氧化钙糊剂能有效控制慢性根尖周炎的炎症状态,是一种较理想的根管消毒剂.%Objective To evaluate the clinical effects of Jinhoujian spry mixing calcium hydroxide paste on chronic periapical periodontitis. Methods 196 teeth with chronic periapical periodontitis were selected, and randomly divided into two groups: experimental group and control group. After root canel preparing, the root canels of teeth in the experimental group were enveloped with Jinhoujian spry mixing calcium hydroxide paste and the control group were enveloped with calcium hydroxide paste. The clinical effects were evaluated 1-2 week after treatment. Results The effective rate in the experimental group was significantly higher than the control group (91.0% vs 81.21%, P<0.05). The inefficiency in the experimental group was significantly lower than the control group (9.0% vs 19.79%, P< 0.05). Conclusion Jinhoujian spry mixing calcium hydroxide paste is a kind of ideal root canal disinfectant, and can effectively control the inflammation of chronic periapical periodontitis

  9. 自固化磷酸钙糊剂和氢氧化钙碘仿糊剂用于乳磨牙活髓切断术后盖髓剂的临床疗效观察%Comparison study of pulpotomy with calcium phosphate cement paste vs calcium hydroxide/iodoform paste in primary molars

    Institute of Scientific and Technical Information of China (English)

    韩汉; 吴佩玲

    2014-01-01

    Objective To investigate effectiveness of calcium phosphate cement paste vs calcium hydroxide/iodoform paste,when it performed direct capping after vital pulpotomy of deciduous molars,which acci-dentally exposed pulp because treatment of deep carie,in order to that provide a reference about choicing of capping agent for clinicians.Methods Select the children 4-6 years old met the inclusion criteria totaled 9 6 (9 6 teeth),The patients were randomly divided into calcium phosphate cement paste group (ex-perimental group)and calcium hydroxide/iodoform cement paste group (control group)and informed con-sent of the parents of these children.after 3 months,6 months and 1 2 months were observed.Results All patients without any pain and other adverse reactions.The clinical efficiency in controlled group and exper-imental group were 94% and 97.8% after 3 months operation,were 92.0% and 95.7% after 6 months, were 92.0 % and 87.0%,after 12 months,respectively .There were no statistically significant (P >0.05). Conclusion Calcium phosphate cement paste,as a capping agent for primary teeth pulpotomy,after cov-ering the pulp section,can play effectively isolated from external stimuli and retain the residual activity of the purpose of pulp,It is close to the clinical efficacy of calcium hydroxide/iodoform paste,The findings provide more option of capping agent in pulpotomy surgery for dental clinicians.%目的:探讨自固化磷酸钙与氢氧化钙碘仿糊剂用于乳磨牙活髓切断术后盖髓剂的临床疗效。方法选择4~6岁因第一、第二乳磨牙龋病在治疗过程中因去除龋坏组织导致牙髓意外暴露欲行活髓切断术的96例患儿(96颗患牙),随机分为两组,试验组50颗患牙,采用自固化磷酸钙糊剂作为盖髓剂,对照组46颗患牙,采用氢氧化钙碘仿糊剂作为盖髓剂,于术后3、6、12个月复查。结果所有患儿无明显疼痛等不适,也无不良反应;术后3

  10. In vitro antimicrobial activity of different gutta-percha points and calcium hydroxide pastes Atividade antimicrobiana in vitro de diferentes composições de cones de guta-percha e pastas de hidróxido de cálci

    Directory of Open Access Journals (Sweden)

    Juliane Maria Guerreiro Tanomaru

    2007-03-01

    Full Text Available The aim of this study was to evaluate the antimicrobial activity of different trademarks and compositions of gutta-percha points and calcium hydroxide pastes used in endodontic therapy. The evaluated material consisted of gutta-percha points containing calcium hydroxide (RoekoTM, gutta-percha points containing chlorhexidine (RoekoTM, two convencional gutta-percha points (Endo PointsTM and RoekoTM and two calcium hydroxide pastes (CalenTM and Calen/PMCC TM. Antimicrobial tests included five species of microorganisms: Escherichia coli (ATCC10538, Staphylococcus epidermidis (ATCC12228, Staphylococcus aureus (ATCC6538, Pseudomonas aeruginosa (ATCC27853, and Micrococcus luteus (ATCC9341. The Agar difusion method was employed. The plates were kept at room temperature for 2 h for prediffusion and then incubated at 37°C for 24 h. The triphenyltetrazolium chloride gel was added for optimization and the zones of inhibition were measured. Statistical evaluation was carried out using analysis of variance and Tukey Test. The obtained results showed that all microbial species used in the study were inhibited by the gutta-percha points containing chlorhexidine and by the calcium hydroxide pastes (CalenTM and Calen/PMCC TM, with similar results (p > 0.05. No antimicrobial activity was observed for the other groups. It was concluded that the gutta-percha points containing chlorhexidine presented antimicrobial activity, whereas the gutta-percha points containing calcium hydroxide did not.O objetivo deste estudo foi a avaliação da atividade antimicrobiana de diferentes marcas e composições de cones de guta-percha e pastas à base de hidróxido de cálcio utilizados em endodontia. Os materiais avaliados foram: cones de guta-percha contendo hidróxido de cálcio (RoekoTM, cones de guta-percha contendo clorexidina (RoekoTM, duas marcas de cones de guta-percha (Endo PointsTM e RoekoTM e duas pastas à base de hidróxido de cálcio (CalenTM e Calen/PMCC TM. Os

  11. Influence of calcium hydroxide on dyes for dentin labeling, anlyzed by means of a new methodology Influência do hidróxido de cálcio sobre corantes na marcação dentinária, analisada por meio de uma nova metodologia

    Directory of Open Access Journals (Sweden)

    Ivaldo Gomes de Moraes

    2005-09-01

    Full Text Available The objective of this study was to evaluate the influence of calcium hydroxide in intracanal dressing on the ability of the dyes rhodamine B and methylene blue to label the dentine. Forty extracted human mandibular premolars had their canals instrumented and were divided into four groups: in two groups, the canals were filled with a calcium hydroxide paste and the others remained in distilled water. After 15 days, in two groups (with and without dressing, the canals were obturated with sealer containing methylene blue, whereas the others contained rhodamine B. For analysis, the roots were transversally sectioned in their cervical, medium and apical thirds, and the labeling was analyzed. The Mann-Whitney test showed statistically significant difference between the dressing/methylene blue group and the others. Based on these results, it was concluded that calcium hydroxide in intracanal dressing negatively interferes with the labeling ability of methylene blue.Objetivou-se avaliar a influência do curativo intracanal de hidróxido de cálcio sobre a capacidade dos corantes azul de metileno e rhodamine B de marcar a dentina, quando incorporados à massa obturadora, no momento da espatulação. Quarenta pré-molares inferiores humanos extraídos tiveram seus canais instrumentados sendo, então, divididos em quatro grupos. Em dois grupos, os canais foram preenchidos com pasta de hidróxido de cálcio e propilenoglicol por 15 dias. Os outros, permaneceram em água destilada. Após a remoção do curativo, todos os canais foram obturados com condensação lateral e cimento de óxido de zinco e eugenol acrescidos de azul de metileno ou rhodamine B. Assim, em dois grupos (com e sem curativo, os canais foram obturados com cimento contendo azul de metileno e os outros, rhodamine B. Decorridos 15 dias, as raízes foram seccionadas transversalmente nos terços cervical, médio e apical, procedendo-se à análise da marcação, com atribuição de escores

  12. 氢氧化钙对人牙髓细胞中骨涎蛋白基因转录的影响%Calcium hydroxide regulates bone sialoprotein gene transcription in human dental pulp cells

    Institute of Scientific and Technical Information of China (English)

    王霜; 陈阵; 宁佳; 高平

    2012-01-01

    Objective To analyze the effects of calcium hydroxide[ Ca(OH) 2 ] on transcription of the bone sialoprotein(BSP) gene in human dental pulp cells. Methods Human dental pulp tissues were collected from extracted teeth for orthodontic reason. In cell culture media,different dose (0.012,0.120,0.400 and 1.200 mmol/L)of Ca(OH) 2 was added.Total RNA of cells were extracted.The best dose of Ca (OH)2 on human BSP was determined with the real-time polymerase chain reaction(PCR). Further,the time(0,3,6,12,24 h) effects of the best dose Ca(OH)2 on human BSP,runt-related transcription factor-2(Runx-2) and osterix(OSX) mRNA levels were determined with PCR.Further method included transient transfection assays,linking chimeric constructs of the human BSP gene promoter to a luciferase reporter gene,then ransfected using lipofectamine in cells and measured the luciferase activities of BSP gene promoter. Results With the real-time PCR,the optimal Ca (OH)2 concentration was determined as 1.200 mmol/L.With this concentration at different time points(0,3,6,12 and 24 h),the levels of BSP mRNA increased at 6 h ( 1.45 ±0.36),reached maximal at 12 h(2.66 ±0.18) ;the levels of Runx-2mRNA increased at 6 h(2.38 ±0.08),at 12 h(2.73 ±0.16),and decreased at 24 h. OSX mRNA could be recognized at 12 h,reached maximal levels at 24 h ( 3.30 ± 0.062).Transient transfection assays showed that treatment of human dental pulp cells with Ca(OH) 2 (1.200 mmol/L) increased the luciferase activities of the constructs between - 84LUC and - 868LUC at 12 h (2.00 ~ 2.60 fold).Conclusions This study demonstrate that Ca(OH) 2 could stimulate BSP transcription between -84LUC and -868LUC in the human BSP gene promoter in human dental pulp cells.%目的 观察氢氧化钙对人牙髓细胞中骨涎蛋白基因转录的影响,研究氢氧化钙诱导矿化的机制,为研制更有效的盖髓剂提供实验依据.方法 收集天津医科大学口腔医院口腔颌面外科门诊因正畸拔除的双尖牙15

  13. REGIOSELECTIVE REACTIONS OF 3-ALKYL-1-PHENYL-2-PYRAZOLIN-5-ONES WITH ACYL HALIDES IN THE PRECENCE OF NONOSIZED MAGNESIUM HYDROXIDE AS A HIGHLY EFFECTIVE HETEROGENOUS BASE CATALYST Regioselektive Reaktionen von 3-Alkyl-1-PHENYL-2-pyrazolin-5-ONES Mit Acylhalogeniden IN DER PRECENCE DER NONOSIZED MAGNESIUM HYDROXIDE als hochwirksame heterogene BASE CATALYST

    Directory of Open Access Journals (Sweden)

    Hassan Sheibani and Bahman Massomi Nejad

    2012-07-01

    Full Text Available 4-Acyl-3-alkyl-1-phenyl-2-pyrazolin-5-one derivatives were prepared by the regioselective acylation of 3-alkyl-1-phenyl-2-pyrazolin-5-ones in the presence of base catalysts such as calcium hydroxide [Ca(OH2], magnesium hydroxide [Mg(OH2] and nanosized magnesium hydroxide. In the presence of nanosized magnesium hydroxide, excellent yields of products were obtained and reaction times were significantly reduced.

  14. Novel synthesis of layered double hydroxides (LDHs) from zinc hydroxide

    Science.gov (United States)

    Meng, Zilin; Zhang, Yihe; Zhang, Qian; Chen, Xue; Liu, Leipeng; Komarneni, Sridhar; Lv, Fengzhu

    2017-02-01

    The most common synthesis methods for layered double hydroxides (LDHs) are co-precipitation and reconstruction, which can have some limitations for application. Here, we report a novel synthesis method for LDHs. We use zinc hydroxide as the precursor to synthesize LDHs phase through a simple transformation process of zinc hydroxide phase. For this transformation process, aluminum can enter into zinc hydroxide and replace zinc quickly to transform it into LDH by creating positive charges in the zinc hydroxide solid phase. The mechanism of LDH formation was through Al3+ reaction first with zinc hydroxide followed by recrystallization of the original structure of zinc hydroxide. Thus, the new process of LDH formation involves a reaction of Al to substitute for Zn and recrystallization leading to LDH and the final pH influences the crystallization of LDHs by this process. In addition, Cr3+ was employed as a trivalent cation for LDH formation to react with zinc hydroxide, which also led to LDH structure.

  15. Eficacia de la solución de hidróxido de calcio a 20% en la reducción de microorganismos asociados a la cárie de dentina Efficacy of 20% calcium hydroxide solution for reduction of microorganisms in carious dentin

    Directory of Open Access Journals (Sweden)

    IVA Pinheiro

    2005-06-01

    Full Text Available Objetivo: Evaluar la eficácia da solución de hidróxido de calcio a 20% en la reducción de microorganismos asociados a la carie de dentina. Metodología:Treinta preparos cavitários fueron realizados en molares permanentes de 30 indivíduos entre las edades de 9 a 18 años. Solución salina reductora fue utilizada como líquido de colecta para la recuperación de microorganismos, antes y después del lavado cavitário. Las muestras fueron colocadas en placas de agar sangre de carnero e incubadas en anaerobiosis por 48 horas a 37ºC. Después Del crecimiento bacteriano, se realizo un análisis semi cuantitativo y cualitativo de las bacterias, a través de hibridización DNA-DNA para 23 tipos de bacterias. Resultados: Una reducción significativa de la cantidad de microorganismos en las muestras colectadas después del lavado de la cavidad con solución de hidróxido de calcio fue observada cuando comparado con el momento anterior al lavado. Del total de muestras que presentaron microorganismos en la cavidad recién preparada, 46,15% presentaron eliminación de éstos microorganismos después del lavado con agua de cal y 53,84% presentaron reducción significativa del número de microorganismos. El teste t pareado de Student mostró una diferencia extremamente significativa (p=0,0007 entre el momento anterior y posterior al lavado. Con relación al tipo de bacterias encontradas después Del lavado de la cavidad con solución de hidróxido de calcio, se observó reducción considerable de S. anginosus, S. mitis y S. sobrinus, así como de S. aureus y S. epidermidis, a pesar de no ser significativa (p>0,05. Conclusión: La solución de hidróxido de calcio parece ser un método de limpieza cavitária eficaz en la reducción de la microbiota asociada a la carie de dentina.Objective: This study aimed to test the effectiveness of the cavity cleansing solution (calcium hydroxide 20% in the elimination or reduction of microorganisms associated to

  16. Effect of biomechanical preparation and calcium hydroxide pastes on the antisepsis of root canal systems in dogs Ação do preparo biomecânico e de pastas à base de hidróxido de cálcio na anti-sepsia do sistema de canais radiculares de cães

    Directory of Open Access Journals (Sweden)

    Janir Alves Soares

    2005-03-01

    Full Text Available In the endodontic treatment of root canals with necrotic pulps associated with periapical radiolucent areas, one of the main objectives of treatment consists in eliminating the microorganisms spread throughout the ramifications of the root canal system. The scope of this study was to evaluate the antiseptic efficacy of biomechanical preparation and two calcium hydroxide-based pastes, in dogs' teeth with experimentally induced chronic periapical lesions. After initial microbiological sampling, instrumentation of the root canals was undertaken using the conventional technique, using K type files used in conjunction with a solution of 5.25% sodium hypochlorite. After ninety-six hours, further microbiological sampling was undertaken and Calen/CPMC or Calasept pastes were applied for 15 and 30 days. Ninety six hours after the removal of the medication, the third microbiological sampling was undertaken and finally histomicrobiological analysis followed using Brown & Brenn staining. The results were analyzed using the Kruskall-Wallis test, with a level of significance established at 5% (p0.05, characterized by an elevated incidence of cocci, bacilli and filaments, predominantly gram-positive, in root canals, secondary canals and accessories, apical cementoplasts and dentinal tubules, but with a low incidence of microorganisms in areas of cementum resorption and the periapical lesion. The biomechanical preparation and intracanal dressing based on calcium hydroxide were important in the antisepsis of the root canal; however, both procedures did not produce significant changes in the microbiological aspects of the root canal system.No tratamento endodôntico dos canais radiculares com polpa necrótica associados à áreas radiolúcidas periapicais, um dos principais objetivos consiste em eliminar os microrganismos situados em todo o sistema de ramificações. Por conseguinte, o objetivo deste estudo foi avaliar a eficácia anti-séptica do preparo

  17. Effect of rotary instrumentation and of the association of calcium hydroxide and chlorhexidine on the antisepsis of the root canal system in dogs Efeito da instrumentação automatizada e da associação hidróxido de cálcio e clorexidina na anti-sepsia de canais radiculares de cães

    Directory of Open Access Journals (Sweden)

    Janir Alves Soares

    2006-04-01

    Full Text Available This study aimed at evaluating the antisepsis of the root canal system (RCS and periapical region (PR provided by rotary instrumentation associated with chlorhexidine + calcium hydroxide as intracanal medicament. Chronic periapical lesions were induced in 26 pre-molar roots in two dogs. After microbiological sampling, automatic instrumentation using the Profile system and irrigation with 5.25% sodium hypochlorite solution, with a final rinse of 14.3% EDTA followed by profuse irrigation with physiological saline were carried out in 18 root canals. After drying the canals, a paste based on calcium hydroxide associated with a 2% chlorhexidine digluconate solution was placed inside them. After 21 days, the medication was removed, leaving the root canals empty and coronally sealed. After 96 hours, a final microbiological sample was obtained, followed by histomicrobiological processing by the Brown & Brenn method. Eight untreated root canals represented the control group (C-G. Based on the Mann-Whitney test at a confidence level of 5% (p Este estudo objetivou avaliar a anti-sepsia do sistema de canais radiculares (SCR e da região periapical (RP proporcionada pela instrumentação automatizada associada a medicação intracanal à base de hidróxido de cálcio + clorexidina. Lesões periapicais crônicas foram induzidas em 26 raízes de pré-molares de dois cães. Após amostragem microbiológica, procedeu-se à instrumentação automatizada de 18 canais radiculares (CR utilizando-se o sistema Profile e a solução de hipoclorito de sódio a 5,25%, com irrigação final com EDTA a 14,3%, seguida de irrigação profusa com soro fisiológico. Após se secarem os canais, foi colocada em seu interior uma pasta à base de hidróxido de cálcio P.A. associada à solução de digluconato de clorexidina a 2%. Transcorridos 21 dias, removeu-se a medicação, deixando-se os CR vazios e selados coronariamente. Após 96 horas, obteve-se a amostra microbiol

  18. In vitro evaluation of the morphologic changes on the root dentine irradiated by CO{sub 2} laser associated or not to calcium hydroxide application; Avaliacao in vitro das alteracoes morfologicas da superficie da dentina radicular irradiada pelo laser de CO{sub 2} associado ou nao a aplicacao de hidroxido de calcio

    Energy Technology Data Exchange (ETDEWEB)

    Romano, Ana Cristina Cury Camargo

    2003-07-01

    This in vitro study has evaluated the structural changes on the root dentine irradiated by a CO{sub 2} laser associated or not to calcium hydroxide application, from the irradiated surface analysis by means of Scanning Electronic Microscopy (SEM). The purpose of this evaluation has been the study of an alternative method for the treatment of dentine hypersensitivity. Fourteen human teeth were utilized, third molars, divided into 7 groups. Group I (control group) to which no treatment was applied; Groups II, III and IV were given an application of Ca (OH){sub 2} paste followed by C0{sub 2} laser irradiation, lasting 5 seconds each with intervals of 10 seconds between each application, with continuous emission, power of 0.5 W (Group II), 1.0 W (Group III), and 1.5 W (Group IV); Groups V, VI, and VII were given laser irradiations without the Ca (OH){sub 2} paste following the same parameters applied to groups II, III, and IV respectively. Morphologic changes suggesting to fusion and re-solidification have been observed, as well as the presence of material obstructing the whole analyzed surface on groups II, III, and IV (laser + Ca (OH){sub 2}). As for groups V, VI, and VII, it has been observed fusion, re-solidification, and cracks, and these results being statistically significant when compared the '(Ca (OH){sub 2})' groups to the laser groups. No statistically significant differences were observed regarding the different powers applied in the groups that used the same treatment. Despite this result, it can be stated that powers above 1.0 W (DP = 125,38 W/cm{sup 2}) are unfavorable due to the undesirable morphologic alterations and aesthetic compromising. (author)

  19. Effects of mineral trioxide aggregate and calcium hydroxide on the proliferation and differentiation capacity of pulp cells of primary teeth%三氧化矿物凝聚体对人乳牙牙髓细胞增殖和分化影响的实验研究

    Institute of Scientific and Technical Information of China (English)

    王敏永; 刘鹤; 李盛林; 秦满

    2008-01-01

    Objective To investigate the effects of mineral trioxide aggregate (MTA) and calcium hydroxide on the proliferation and differentiation capacity of pulp cells of primary teeth. Methods Pulp cells were isolated from the retained primary teeth without apparent root resorption and cultured. The cells of 4-8 passages were used in the study. Cell proliferation was detected by MTr array, van Kossa staining employed to observe the formation of mineralized nodules and mRNA expression of alkaline phosphataso (ALP) and dentin sialophosphoprotein (DSPP) determined by real time PCR. Results MTA-treated cells proliferated signifieantly faster than the other two groups (F=1835.065, P 0.05). Either ALP or DSPP mRNA expression showed significant difference among the three groups (F=349.651, P 0.05).三组间ALP基因表达量差异有统计学意义(F=349.651,P<0.01),氢氧化钙组显著低于对照组和MTA组,MTA组显著高于氢氧化钙组和对照组;三组间DSPP基因表达量差异也有统计学意义(F=1653.001,P<0.01),氢氧化钙组显著低于对照组和MTA组,MTA组显著高于氢氧化钙组和对照组.结论 从促进乳牙牙髓细胞的增殖和分化来看,MTA比氢氧化钙更适合作为乳牙的盖髓剂.

  20. 21 CFR 184.1428 - Magnesium hydroxide.

    Science.gov (United States)

    2010-04-01

    ... hydration of reactive grades of magnesium oxide. (b) The ingredient meets the specifications of the Food... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Magnesium hydroxide. 184.1428 Section 184.1428 Food... Specific Substances Affirmed as GRAS § 184.1428 Magnesium hydroxide. (a) Magnesium hydroxide (Mg(OH)2,...

  1. Contribution to the knowledge of nickel hydroxide electrodes. 5. Analysis and electrochemical behavior of cadmium nickel hydroxides

    Science.gov (United States)

    Bode, H.; Dennstedt, W.

    1981-01-01

    Electrochemical experiments performed at sintered and bulk electrodes show that beta nickel hydroxide contains an electrochemically inactive proportion of cadmium hydroxide of up to 10%. The electrochemically ineffective cadmium hydroxide is homogeneously dissolved in beta nickel hydroxide.

  2. Antibacterial effect of root canal preparation and calcium hydroxide paste (Calen intracanal dressing in primary teeth with apical periodontitis Efeito antibacteriano do preparo biomecânico e do curativo de demora com pasta à base de hidróxido de cálcio (Calen em dentes decíduos com lesão periapical

    Directory of Open Access Journals (Sweden)

    Gisele Faria

    2005-12-01

    Full Text Available The aim of this study was to evaluate the antibacterial action of root canal mechanical preparation using 2.5% sodium hypochlorite as the irrigating solution and a calcium hydroxide paste as the antibacterial intracanal dressing in human primary teeth root canals with pulp necrosis and apical periodontitis by means of microbial culture. A total of 26 root canals of human primary teeth with pulp necrosis and apical periodontitis were used. Samples were collected before, 72h after biomechanical treatment and 72h after removal of the intracanal dressing. Comparison by Wilcoxon test showed that root canal mechanical preparation effectively eliminated all microorganisms in 20% of the root canals, and the intracanal dressing in 62.5%; however, the cumulative action of biomechanical treatment and intracanal dressing eliminated the microorganisms of 70% of the root canals (pO objetivo do presente estudo foi avaliar, por meio de cultura bacteriológica, a ação antibacteriana do preparo biomecânico utilizando como solução irrigadora o hipoclorito de sódio a 2,5% e da pasta Calen utilizada como curativo de demora em canais radiculares de dentes decíduos de humanos com necrose pulpar e lesão periapical. Foram selecionados 26 dentes decíduos de humanos portadores de necrose pulpar e lesão periapical. As colheitas microbiológicas foram efetuadas antes e 72 horas após o preparo biomecânico e 72 horas após a remoção do curativo de demora. A comparação por meio do teste de Wilcoxon mostrou que o preparo biomecânico foi eficaz na eliminação dos microrganismos dos canais radiculares em 20% dos casos e o curativo de demora em 62,5%, enquanto que a ação cumulativa do preparo biomecânico e do curativo de demora eliminou os microrganismos em 70,0% dos casos (p<0.001. Pôde-se concluir que o preparo biomecânico, isoladamente, apresentou resultados microbiológicos inferiores àqueles obtidos quando o mesmo foi associado ao curativo de demora

  3. Supermolecular layered dou- ble hydroxides

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Research progresses in the layered double hydroxides ·mH2O intercalated with metal coordinate ions or oxometalates in the last ten years are reviewed. These layered double hydroxides are mainly intercalated with polyoxometalate (POM) ions, a LiAl-LDH photochemical assembly containing TiO2 and CH3(CH2)12COO- anions, together with Zn(TPPC) (porphy-rin derivate) and macrocyclic ligand-containing porphyrin derivate anions. Emphasis is put on the synthesis methods for intercalation of the anions into the interlayer regions, the characterization techniques and structures for the layered compounds and the newest research progress in the fields such as catalysis. The review also forecasts the prospects of the field.

  4. Pulpal response of dogs primary teeth to an adhesive system or to a calcium hydroxide cement Resposta pulpar de dentes decíduos de cães a um sistema adesivo ou ao cimento de hidróxido de cálcio

    Directory of Open Access Journals (Sweden)

    Rosângela Almeida RIBEIRO

    2000-03-01

    Full Text Available The aim of this study was to evaluate the pulpal response of dogs primary teeth to an adhesive system or to a calcium hidroxide cement after mechanic exposure of the pulp. Three mongrel dogs were used and ten class V cavities were prepared on their teeth. A mechanic pulp exposure was produced with a sterile exploratory probe in the central portion of each cavity and bleeding was controlled with dry sterile cotton pellets. Enamel, dentin and the site of the pulp exposure of five teeth were etched with 35% phosphoric acid followed by the application of an adhesive system (Scotchbond Multi-Purpose - 3M. In the other five teeth, calcium hydroxide cement (Hydro C - Dentsply was applied on the site of the pulp exposition before application of the adhesive system (Scotchbond Multi-Purpose - 3M. All teeth were restored with a resin composite (Z-100 - 3M. After 7, 30 or 45 days the dogs were anesthetized and perfused with saline followed by a solution of neutral buffered formalin. Maxilla and mandible were sectioned into three parts and placed in a solution for demineralization. Following bone demineralization, all teeth were cut, trimmed, embedded in paraffin and longitudinally cut. Then, the teeth were stained with hematoxilin and eosin and observed under a light microscope. The results obtained with the treatments proposed in this study showed the presence and persistence of an inflammatory response of different intensities at the three experimental periods. There was no variation in the inflammatory response regarding the different treatments performed.O objetivo deste estudo foi de avaliar a resposta pulpar de dentes decíduos de cães à um sistema adesivo ou a um cimento de hidróxido de cálcio após exposição mecânica da polpa. Foram utilizados três cães sem raça definida, e nestes foram realizados dez preparos cavitários classe V. Uma exposição pulpar mecânica foi produzida com uma sonda exploradora esterilizada, na porção central

  5. Comparison of Pulp Regeneration with Absorbable Gelatin Sponge Stent Combined MTA and Calcium Hydroxide Cover%可吸收明胶海绵支架联合三氧化矿物凝聚体与氢氧化钙覆盖诱导体内牙髓再生的疗效比较

    Institute of Scientific and Technical Information of China (English)

    张宇; 魏灼丽; 赵彪; 任延秀

    2016-01-01

    目的:比较可吸收明胶海绵支架联合三氧化矿物凝聚体( MTA)与氢氧化钙覆盖诱导体内牙髓再生的疗效。方法选取重庆三峡中心医院收治的122例(130颗患牙)不可复性牙髓炎患者,采用随机数字表法将其分为观察组61例(66颗患牙)和对照组61例(64颗患牙)。其中观察组采用可吸收明胶海绵支架联合MTA封闭治疗,对照组采用氢氧化钙覆盖治疗,经3个月随访,观察比较两组患者的治疗效果、牙龈活力变化情况。结果术后1周,观察组总的初步成功率为50.0%(33/66),明显高于对照组[12.5%(8/64)],差异有统计学意义(P<0.01);其中观察组急性牙髓炎、慢性闭锁性牙髓炎成功率均高于对照组,差异有统计学意义( P<0.01)。术后1个月,观察组总的阶段成功率为62.1%(41/66),明显高于对照组[18.8%(12/64)],差异有统计学意义(P<0.01);其中观察组急性牙髓炎、慢性闭锁性牙髓炎、慢性增生性牙髓炎成功率均高于对照组,差异有统计学意义(P<0.05)。术后3个月,观察组总的最终成功率为66.7%(44/66),明显高于对照组[21.9%(14/64)],差异有统计学意义(P<0.01);且观察组各型牙髓炎成功率均高于对照组,差异有统计学意义(P<0.05)。结论可吸收明胶海绵支架联合MTA可有效诱导体内牙髓再生,对各型不可复性牙髓炎均有较好的效果,值得推广应用于临床。%Objective To compare the efficacy of pulp regeneration induced by absorbable gelatin sponge stent combined mineral trioxide aggregate(MTA) and calcium hydroxide cover.Methods Total of 122 patients (130 sick teeth) with irreducible pulpitis in Chongqing Three Gorges Central Hospital were chosen,and were randomly divided into observation group 61 cases (66 sick teeth) and control group 61 cases(64 skck

  6. Process for the preparation of calcium superoxide

    Science.gov (United States)

    Ballou, E. V.; Wood, P. C.; Wydeven, T. J.; Spitze, L. A. (Inventor)

    1978-01-01

    Calcium superoxide is prepared in high yields by spreading a quantity of calcium peroxide diperoxyhydrate on the surface of a container, positioning said container in a vacuum chamber on a support structure through which a coolant fluid can be circulated, partially evacuating said vacuum chamber, allowing the temperature of the diperoxyhydrate to reach the range of about 0 to about 40 C; maintaining the temperature selected for a period of time sufficient to complete the disproproriation of the diperoxyhydrate to calcium superoxide, calcium hydroxide, oxygen, and water; constantly and systematically removing the water as it is formed by sweeping the reacting material with a current of dry inert gas and/or by condensation of said water on a cold surface; backfilling the chamber with a dry inert gas; and finally, recovering the calcium superoxide produced.

  7. Pharmacokinetic Profile of Oral Magnesium Hydroxide

    DEFF Research Database (Denmark)

    Dolberg, Mette Konow Bøgebjerg; Nielsen, Lars Peter; Dahl, Ronald

    2016-01-01

    Despite the presumption of a beneficial effect of magnesium (Mg) supplementation on various diseases, little is known concerning the pharmacokinetics of Mg hydroxide. This study was designed to provide a pharmacokinetic profile of Mg hydroxide after a single oral dose. Ten healthy male adults...

  8. Calcium supplements

    Science.gov (United States)

    ... do not help. Always tell your provider and pharmacist if you are taking extra calcium. Calcium supplements ... 2012:chap 251. The National Osteoporosis Foundation (NOF). Clinician's Guide to prevention and treatment of osteoporosis . National ...

  9. Properties of oxide-hydroxide sintered ceramics

    Science.gov (United States)

    Levkov, R. V.; Kulkov, S. N.

    2017-02-01

    In this paper the study of porous ceramics obtained from aluminum hydroxide with gibbsite modification is presented. It was shown that aluminum hydroxide may be used for pore formation and pore volume in the sintered ceramics can be controlled by varying the aluminum hydroxide concentration and sintering temperature. It was shown that compressive strength of alumina ceramics increases by 40 times with decreasing the pore volume from 65 to 15%. Based on these results one can conclude that the obtained structure is very close to inorganic bone matrix and can be used as promising material for bone implants production.

  10. Thermodynamics of Volatile Silicon Hydroxides Studied

    Science.gov (United States)

    Copland, Evan H.; Opila, Elizabeth J.; Jacobson, Nathan S.

    2001-01-01

    Silicon-based ceramics are promising candidate structural materials for heat engines. The long-term stability of these materials to environmental degradation is dependent on the formation and retention of a protective SiO2 layer. It is well known that SiO2 forms stable volatile hydroxides in the presence of water vapor at elevated temperatures. Combustion conditions, which characteristically are at high velocities, contain significant water vapor pressures, and high temperatures tend to promote continuous formation of these hydroxides with resulting material degradation. For the degradation of silicon-based ceramics to be predicted, accurate thermodynamic data on the formation of silicon hydroxides are needed.

  11. Histopathological and histomicrobiological study of root canal therapy medication, comparison of calcium hydroxide versus gutta-percha with zinc oxide/eugenol in the teeth of dogs Avaliação histopatológica e histomicrobiológica de dentes de cães, após tratamento endodôntico com hidróxido de cálcio e guta-percha com óxido de zinco e eugenol

    Directory of Open Access Journals (Sweden)

    Léslie M. Domingues-Falqueiro

    2007-02-01

    Full Text Available The presence of microorganisms in dental structures with experimentally induced necrosis was evaluated. The materials were tested to evaluate their antimicrobial activity and tissue repair efficacy. Four dogs were used in this experiment, with a total of 64 roots of premolar teeth, divided into three groups. The root canals of Group I were filled with gutta-percha and zinc oxide/eugenol cement; Group II were filled with calcium hydroxide, and Group III were not filled. All animals were clinically and radiographically examined 15 days after surgery andthen again every subsequent 15 days until 120 days, when the teeth were extracted en bloc.Histopathological analysis showed inflammatory infiltration, cement and bone resorption andnecrotic tissue in the apical delta in different proportions. Histomicrobiological analysis showedthe presence of microorganisms inside the teeth structures, with different concentrationsaccording to the treatment used. There was statistical significance between the groups(p>0.05. Gutta-percha with zinc oxide/eugenol demonstrated good antimicrobial activity;calcium hydroxide was not efficient. The conclusion of this study is that gutta-percha withzinc oxide/eugenol is the better protocol for filling root canals in dogs.Avaliou-se a presença de microrganismos nas estruturas dentais com necrose pulpar induzida experimentalmente, testando a eficácia de materiais com relação à atividade antibacteriana e influência no reparo tecidual. Utilizaram-se quatro cães, totalizando 64 raízes, provenientes de pré-molares, divididas em grupos. O Grupo I foi obturado com guta percha e cimento à base de óxido de zinco e eugenol, o Grupo II, com hidróxido de cálcio e o Grupo III, não foram obturados. Todos tiveram controle clínico e radiográfico quinzenal e após 120 dias, foram extraídos em bloco para análises. A histopatologia evidenciou infiltrado inflamatório, reabsorção cementária e óssea e tecido necrótico no

  12. Nickel hydroxide precipitation from aqueous sulfate media

    Science.gov (United States)

    Sist, Cinziana; Demopoulos, George P.

    2003-08-01

    Hydrometallurgical processing of laterite ores constitutes a major industrial and R&D activity in extractive metallurgy. In some of the process flowsheets, nickel hydroxide precipitation is incorporated. For these operations, the optimization of nickel hydroxide precipitation is important to assure efficiency and product quality. The main objective of this investigation was to study and improve the precipitation characteristics of Ni(OH)2 in a sulfate system using supersaturation controlled precipitation.

  13. Effect of different irrigation techniques on the removal of calcium hydroxide paste from an artificial root canal cavity of internal root resorption:an in vitro study%不同冲洗技术去除模拟牙内吸收窝洞中氢氧化钙糊剂效果的体外研究

    Institute of Scientific and Technical Information of China (English)

    刘贺; 钱君荣; 耿海霞

    2016-01-01

    目的:评估不同冲洗技术去除模拟牙内吸收窝洞内氢氧化钙糊剂的效果。方法:收集110颗单根离体牙, ProTaper预备至F3。将牙根纵向劈成两半,制备标准化的模拟牙内吸收窝洞后将两半牙根复位。5颗牙齿作为阴性对照组,不向根管内导入氢氧化钙糊剂。105颗牙齿导入氢氧化钙糊剂,其中5颗作为阳性对照组不去除根管中的氢氧化钙糊剂,其余100颗牙齿根据使用的不同冲洗技术随机分成5组(n=20):常规冲洗针头冲洗组、主尖锉清理组、根管刷刷洗组、超声荡洗组、音波震荡组。体式显微镜下观察使用5种不同冲洗技术去除模拟牙内吸收窝洞后氢氧化钙糊剂剩余的量,使用van der Sluis 4级评分系统进行评分,Kruskal-Wallis检验以及Mann-Whitney检验(P<0.05)对数据进行统计分析。结果:超声荡洗组、音波震荡组较其他组模拟牙内吸收窝洞内氢氧化钙糊剂剩余的量较少(P<0.05)。超声荡洗组与音波震荡组间无明显统计学差异(P>0.05)。常规冲洗针头冲洗组、主尖锉清理组和根管刷刷洗组间无明显统计学差异(P>0.05)。结论:超声荡洗和音波震荡去除模拟牙内吸收窝洞内氢氧化钙糊剂效果较好。%Objective:To evaluate the efficacy of different irrigation techniques to remove calcium hydroxide(CH) from a simulated internal root resorption cavity. Method:110 clinically extracted teeth with single root were collected and prepared using the ProTaper system to size F3.The roots were split longitudinally,standardized simulated internal root re-sorption cavities were prepared in the two root halves,and the root halves were reassembled. The root canals of 5 teeth that were not filled with CH served as the negative control group. The root canals of 105 teeth were filled with CH,5 of them were not subjected to the CH removal procedure,antoher 100 teeth were

  14. Calcium in diet

    Science.gov (United States)

    ... D is needed to help your body use calcium. Milk is fortified with vitamin D for this reason. ... of calcium dietary supplements include calcium citrate and calcium carbonate. Calcium citrate is the more expensive form of ...

  15. Aluminium hydroxide-induced granulomas in pigs

    DEFF Research Database (Denmark)

    Valtulini, S; Macchi, C; Ballanti, P

    2005-01-01

    The effect of intramuscular injection of 40 mg/2 ml aluminium hydroxide in the neck of pigs was examined in a number of ways. The investigation followed repeated slaughterhouse reports, according to which 64.8% of pigs from one particular farm were found at slaughter to have one or more nodules...... in the muscles of the neck (group slaughtered). The pigs had been injected with a vaccine containing 40 mg/2 ml dose of aluminium hydroxide as adjuvant. Research consisted of two phases: first, an epidemiological study was carried out, aimed at determining the risk factors for the granulomas. The results...... and adjuvant) to pigs inoculated twice with apyrogenic bi-distilled water (group water) and to pigs inoculated once with the adjuvant and once with apyrogenic bi-distilled water (group adjuvant/water). Both studies agreed in their conclusions, which indicate that the high amount of aluminium hydroxide...

  16. Surface Acidity of Amorphous Aluminum Hydroxide

    Institute of Scientific and Technical Information of China (English)

    K. FUKUSHI; K. TSUKIMURA; H. YAMADA

    2006-01-01

    The surface acidity of synthetic amorphous Al hydroxide was determined by acid/base titration with several complementary methods including solution analyses of the reacted solutions and XRD characterization of the reacted solids. The synthetic specimen was characterized to be the amorphous material showing four broad peaks in XRD pattern. XRD analyses of reacted solids after the titration experiments showed that amorphous Al hydroxide rapidly transformed to crystalline bayerite at the alkaline condition (pH>10). The solution analyses after and during the titration experiments showed that the solubility of amorphous aluminum hydroxide, Ksp =aAl3+/a3H+,was 1010.3,The amount of consumption of added acid or base during the titration experiment was attributed to both the protonation/deprotonation of dissolved Al species and surface hydroxyl group. The surface acidity constants, surface hydroxyl density and specific surface area were estimated by FITEQL 4.0.

  17. Calcium Electroporation

    DEFF Research Database (Denmark)

    Frandsen, Stine Krog; Gibot, Laure; Madi, Moinecha;

    2015-01-01

    BACKGROUND: Calcium electroporation describes the use of high voltage electric pulses to introduce supraphysiological calcium concentrations into cells. This promising method is currently in clinical trial as an anti-cancer treatment. One very important issue is the relation between tumor cell kill...... efficacy-and normal cell sensitivity. METHODS: Using a 3D spheroid cell culture model we have tested the effect of calcium electroporation and electrochemotherapy using bleomycin on three different human cancer cell lines: a colorectal adenocarcinoma (HT29), a bladder transitional cell carcinoma (SW780......), and a breast adenocarcinoma (MDA-MB231), as well as on primary normal human dermal fibroblasts (HDF-n). RESULTS: The results showed a clear reduction in spheroid size in all three cancer cell spheroids three days after treatment with respectively calcium electroporation (p

  18. Layered double hydroxide stability. 1. Relative stabilities of layered double hydroxides and their simple counterparts

    Science.gov (United States)

    Boclair, J. W.; Braterman, P. S.

    1999-01-01

    Solutions containing di- and trivalent metal chlorides [M(II) = Mg2+, Zn2+, Co2+, Ni2+, Mn2+; M(III) = Al3+, Fe3+] were titrated with NaOH to yield hydrotalcite-like layered double hydroxides (LDH), [[M(II)]1-x[M(III)]x(OH)2][Cl]x yH2O, by way of M(III) hydroxide/hydrous oxide intermediates. Analysis of the resultant titration curves yields nominal solubility constants for the LDH. The corresponding LDH stabilities are in the order Mg hydroxides/hydrous oxides is discussed.

  19. Structural transformation of nickel hydroxide films during anodic oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Crocker, R.W.; Muller, R.H.

    1992-05-01

    The transformation of anodically formed nickel hydroxide/oxy-hydroxide electrodes has been investigated. A mechanism is proposed for the anodic oxidation reaction, in which the reaction interface between the reduced and oxidized phases of the electrode evolves in a nodular topography that leads to inefficient utilization of the active electrode material. In the proposed nodular transformation model for the anodic oxidation reaction, nickel hydroxide is oxidized to nickel oxy-hydroxide in the region near the metal substrate. Since the nickel oxy-hydroxide is considerably more conductive than the surrounding nickel hydroxide, as further oxidation occurs, nodular features grow rapidly to the film/electrolyte interface. Upon emerging at the electrolyte interface, the reaction boundary between the nickel hydroxide and oxy-hydroxide phases spreads laterally across the film/electrolyte interface, creating an overlayer of nickel oxy-hydroxide and trapping uncharged regions of nickel hydroxide within the film. The nickel oxy-hydroxide overlayer surface facilitates the oxygen evolution side reaction. Scanning tunneling microscopy of the electrode in its charged state revealed evidence of 80 {endash} 100 Angstrom nickel oxy-hydroxide nodules in the nickel hydroxide film. In situ spectroscopic ellipsometer measurements of films held at various constant potentials agree quantitatively with optical models appropriate to the nodular growth and subsequent overgrowth of the nickel oxy-hydroxide phase. A two-dimensional, numerical finite difference model was developed to simulate the current distribution along the phase boundary between the charged and uncharged material. The model was used to explore the effects of the physical parameters that govern the electrode behavior. The ratio of the conductivities of the nickel hydroxide and oxy-hydroxide phases was found to be the dominant parameter in the system.

  20. Single sheet metal oxides and hydroxides

    DEFF Research Database (Denmark)

    Huang, Lizhi

    The synthesis of layered double hydroxides (LDHs) provides a relatively easy and traditional way to build versatile chemical compounds with a rough control of the bulk structure. The delamination of LDHs to form their single host layers (2D nanosheets) and the capability to reassemble them offer ...

  1. Hydroxide catalysis bonding of silicon carbide

    NARCIS (Netherlands)

    Veggel, A.A. van; Ende, D.A. van den; Bogenstahl, J.; Rowan, S.; Cunningham, W.; Gubbels, G.H.M.; Nijmeijer, H.

    2008-01-01

    For bonding silicon carbide optics, which require extreme stability, hydroxide catalysis bonding is considered [Rowan, S., Hough, J. and Elliffe, E., Silicon carbide bonding. UK Patent 040 7953.9, 2004. Please contact Mr. D. Whiteford for further information: D.Whiteford@admin.gla.ac.uk]. This techn

  2. Polysulfide intercalated layered double hydroxides for metal capture applications

    Energy Technology Data Exchange (ETDEWEB)

    Kanatzidis, Mercouri G.; Ma, Shulan

    2017-04-04

    Polysulfide intercalated layered double hydroxides and methods for their use in vapor and liquid-phase metal capture applications are provided. The layered double hydroxides comprise a plurality of positively charged host layers of mixed metal hydroxides separated by interlayer spaces. Polysulfide anions are intercalated in the interlayer spaces.

  3. Effectiveness of NaOCl alone or in combination with EDTA on the diffusion of hydroxyl ions released by calcium hydroxide paste Efetividade do hipoclorito de sódio usado isoladamente ou em associação com o EDTA sobre a difusão de íons hidroxila liberados de pasta de hidróxido de cálcio

    Directory of Open Access Journals (Sweden)

    Mara Cristina Santos Felippe

    2006-01-01

    Full Text Available AIM: To evaluate the effect of different irrigant solutions employed during removal and replacement of calcium hydroxide paste on the diffusion of hydroxyl ions through root canal dentine in vitro. METHODOLOGY: Thirty-five maxillary and mandibular human canines with straight and fully developed roots were used. After mechanical preparation up to 1mm short of tooth length, 30 canals were filled with calcium hydroxide paste and 5 canals were left empty; all teeth had their coronal accesses properly sealed. Teeth were placed in plastic containers with distilled water, and pH was read after 30 days when the paste from 20 teeth was renewed. After removal of the paste by endodontic instrumentation and irrigation with distilled water, canals were replenished with newly mixed paste in Group 1 and 2. In these groups, final irrigation was conducted with 5 mL of EDTA followed by 5 mL of NaOCl in specimens in Group 1, and 5 mL of NaOCl only in specimens in Group 2. In 10 teeth the paste was not replenished at 30 days (Group 3. All specimens were returned to the containers with fresh distilled water, and the pH was recorded after another 30 days. The differences between the first (30d and second (60d pH readings were calculated and submitted to analysis of variance and individual comparisons using the Scheffeé's test. RESULTS: Results of mean analysis on differences of pH readings showed that greater diffusion had occurred on specimens in Group 3. Individual comparisons using Scheffeé's test showed statistical significance between Groups 2 and 3, and equivalence between all other groups. CONCLUSION: It was concluded that the use of EDTA did not enhance diffusion of hydroxyl ions through root canal dentine.OBJETIVO: O objetivo desta pesquisa foi comparar o efeito de diferentes irrigantes, usados durante a troca da pasta de hidróxido de cálcio, sobre a difusão de íons hidroxila. METODOLOGIA: Foram empregados 35 caninos humanos, com canais retos e ra

  4. Calcium and bones

    Science.gov (United States)

    Bone strength and calcium ... calcium (as well as phosphorus) to make healthy bones. Bones are the main storage site of calcium in ... your body does not absorb enough calcium, your bones can get weak or will not grow properly. ...

  5. Calcium Test

    Science.gov (United States)

    ... if a person has symptoms of a parathyroid disorder , malabsorption , or an overactive thyroid. A total calcium level is often measured as part of a routine health screening. It is included in the comprehensive metabolic panel (CMP) and the basic metabolic panel (BMP) , ...

  6. Calcium Carbonate

    Science.gov (United States)

    ... doctor if you have or have ever had kidney disease or stomach conditions.tell your doctor if you are pregnant, plan to become pregnant, or are breast-feeding. If you become pregnant while taking calcium carbonate, call your doctor.

  7. Calcium phosphate bioceramics prepared from wet chemically precipitated powders

    Directory of Open Access Journals (Sweden)

    Kristine Salma

    2010-03-01

    Full Text Available In this work calcium phosphates were synthesized by modified wet chemical precipitation route. Contrary to the conventional chemical precipitation route calcium hydroxide was homogenized with planetary mill. Milling calcium oxide and water in planetary ball mill as a first step of synthesis provides a highly dispersed calcium hydroxide suspension. The aim of this work was to study the influence of main processing parameters of wet chemical precipitation synthesis product and to control the morphology, phase and functional group composition and, consequently, thermal stability and microstructure of calcium phosphate bioceramics after thermal treatment. The results showed that it is possible to obtain calcium phosphates with different and reproducible phase compositions after thermal processing (hydroxyapatite [HAp], β-tricalcium phosphate [β-TCP] and HAp/β-TCP by modified wet-chemical precipitation route. The β-TCP phase content in sintered bioceramics samples is found to be highly dependent on the changes in technological parameters and it can be controlled with ending pH, synthesis temperature and thermal treatment. Pure, crystalline and highly thermally stable (up to 1300°C HAp bioceramics with homogenous grainy microstructure, grain size up to 200–250 nm and high open porosity can be successfully obtained by powder synthesized at elevated synthesis temperature of 70°C and stabilizing ending pH at 9.

  8. Layered Double Hydroxide as Cordycepin Delivery Nanocarrier

    Institute of Scientific and Technical Information of China (English)

    Qin Zheng YANG; Jing YANG; Chang Kai ZHANG

    2006-01-01

    Layered double hydroxide was investigated as cordycepin delivery nanocarrier for the first time in this study. Negatively charged biomolecule-cordycepin was intercalated in the gallery spaces of [Mg-Al-NO3], which was confirmed by the results of X-ray diffraction and electrophoretic mobility. Cell experiment suggested that the new bio-LDH nanohybrid could prevent cordycepin decomposition by adenosine deaminase. This new formulation could possibly be used as a novel form cordycepin intravenous injection.

  9. Thermal behaviour of hydroxides, hydroxysalts and hydrotalcites

    Indian Academy of Sciences (India)

    Parthasarathi Bera; Michael Rajamathi; M S Hegde; P Vishnu Kamath

    2000-04-01

    Mass spectrometric analysis of gases evolved during thermal decomposition of divalent metal hydroxides, hydroxysalts and hydrotalcites show that all these compounds undergo dehydration in the temperature range 30 < T < 220°C followed by decomposition at temperatures above 250°C. The latter step involves simultaneous deanation and dehydroxylation of the layers. Our observations conclusively prove that alternative mechanisms which envisage CO2 evolution due to deanation at lower temperatures proposed by Kanezaki to be wrong.

  10. Nickel hydroxide modified electrodes for urea determination

    Directory of Open Access Journals (Sweden)

    Luiz Henrique Dall´Antonia

    2007-03-01

    Full Text Available Nickel hydroxide films were prepared by electrodeposition from a solution Ni(NO32 0,05 mol L ?¹ on ITO electrodes (Tin oxide doped with Indium on PET-like plastic film, applying a current of - 0,1 A cm ?² during different time intervals between 1800 and 7200 s. The electrochemical behavior of the nickel hydroxide electrode was investigated through a cyclic voltammogram, in NaOH 1,0 mol L ?¹, where it was observed two peaks in the profile in 0,410 and 0,280 V, corresponding to redox couple Ni(II/Ni(III. A sensor for urea presenting a satisfactory answer can be obtained when, after the deposit of the film of Ni(OH2 on the electrode of nickel, it is immersed in a solution of NaOH 1,0 mol L ?¹ and applying a potential of + 0,435 V, where the maximum of the anodic current occurs in the cyclic voltammogram. Analyzing the results it can be observed that, for a range of analite concentration between 5 to 50 m mol L ?¹, the behavior is linear and the sensibility found was of 20,3 mA cm?² (mol L?¹?¹, presenting reproducibility confirming the nickel hydroxide electrodes utilization for the determination of urea.

  11. Adsorption of phosphonate antiscalant from reverse osmosis membrane concentrate onto granular ferric hydroxide.

    Science.gov (United States)

    Boels, Luciaan; Keesman, Karel J; Witkamp, Geert-Jan

    2012-09-04

    Adsorptive removal of antiscalants offers a promising way to improve current reverse osmosis (RO) concentrate treatment processes and enables the reuse of the antiscalant in the RO desalination process. This work investigates the adsorption and desorption of the phosphonate antiscalant nitrilotris(methylenephosphonic acid) (NTMP) from RO membrane concentrate onto granular ferric hydroxide (GFH), a material that consists predominantly of akaganéite. The kinetics of the adsorption of NTMP onto GFH was predicted fairly well with two models that consider either combined film-pore or combined film-surface diffusion as the main mechanism for mass transport. It is also demonstrated that NTMP is preferentially adsorbed over sulfate by GFH at pH 7.85. The presence of calcium causes a transformation in the equilibrium adsorption isotherm from a Langmuir type to a Freundlich type with much higher adsorption capacities. Furthermore, calcium also increases the rate of adsorption substantially. GFH is reusable after regeneration with sodium hydroxide solution, indicating that NTMP can be potentially recovered from the RO concentrate. This work shows that GFH is a promising adsorbent for the removal and recovery of NTMP antiscalant from RO membrane concentrates.

  12. Low sulfur content hot reducing gas production using calcium oxide desulfurization with water recycle

    Energy Technology Data Exchange (ETDEWEB)

    Feinman, J.; Mcgreal, J.E.

    1982-03-23

    A process and apparatus are claimed for producing a low sulfur content, hot reducing gas by desulfurizing hot reducing gas. This is done in the following manner; by contacting the sulfur-bearing hot reducing gas with a bed of a particulate calcium oxide desulfurizing agent to thereby produce a product gas stream and a byproduct calcium sulfide compositions recovering sulfur from the calcium sulfide composition by contacting the calcium sulfide composition with hot liquid water at a temperature and corresponding pressure sufficient to maintain steam in the system and to thereby convert the sulfide to calcium hydroxide and hydrogen sulfide and to produce a liquid water stream containing sulfur; combining the sulfur containing water stream with a fresh water stream and recycling this water stream for contacting the calcium sulfide composition. Preferably water vapor produced in the contacting step is condensed and returned to the system in the final stage of contacting the calcium sulfide composition with hot liquid water.

  13. Polytypic transformations of aluminum hydroxide: A mechanistic investigation

    Institute of Scientific and Technical Information of China (English)

    Thimmasandra Narayan Ramesh

    2012-01-01

    The diffusion of ammonia vapors into a solution of aluminum nitrate or ferric nitrate results in the precipitation of their respective hydroxides and oxyhydroxides.Polymorphic phase formation of aluminum hydroxide is controlled by the rate of crystallization.The PXRD patterns of products obtained via vapor phase diffusion revealed that poorly ordered aluminum hydroxide is formed during the initial stages of crystallization.After 8 days,the formation of the bayerite phase of aluminum hydroxide was observed.Upon prolonged exposure to ammonia vapors,bayerite was transformed into gibbsite.The infrared spectrum of the product confirmed the presence of different polytypic phases of aluminum hydroxide.The results demonstrated that the crystal structure of metal hydroxides is controlled by the rate of crystallization,nature of the metal ion,site selectivity and specificity and preparative conditions.

  14. Preparation and application of magnesium hydroxide%氢氧化镁的制备与应用

    Institute of Scientific and Technical Information of China (English)

    常喜斌; 王冀锋

    2013-01-01

    Methods for preparation of magnesium hydroxide mainly include dolomite method , magne-site method, brucite method, magnesium chloride method (calcium hydroxide precipitation method, am-monia precipitation method , sodium hydroxide , magnesium chloride precipitation method ) , and hexam-moniated magnesium chloride -magnesium chloride method .Magnesium hydroxide can be used in water treatment, flue gas desulfurization , etc., and can also be used as inorganic flame retardants and a pre-cursor of magnesium oxide series products .%氢氧化镁制备方法主要包括:白云石法,菱镁矿法,水镁石法,氯化镁法(氢氧化钙沉淀法、氨沉淀法、氢氧化钠沉淀法),六氨氯化镁-氯化镁法。其可应用于水处理、烟气脱硫等领域,还可用作无机阻燃剂及制备氧化镁系列产品的前驱体。

  15. FIBRED MAGNESIUM HYDROXIDE AND FLAME-RESISTANT POLYENE MATERIAL

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The fibred mangesiun hydroxide from the bracite was treated with a surface active agent. The modified fibred magesium hydroxide as f lame-retardant,boric acid, barium stearate, polydimethyl siloxane fluid,vinyltr iethoxysilane as synergists of the flame-retardant were added to polyene resin. The flame-resistance polyene material prepared meets the requirements of EWCZ -6287-1.

  16. Production of calcium-stearate by lipase using hydrogenated beef tallow.

    Science.gov (United States)

    Lee, Hyang-Bok; Kwon, Jin-Soo; Kim, Young-Bum; Kim, Eun-Ki

    2009-05-01

    Calcium-stearate has been traditionally produced by chemical methods, producing wastes and requiring high energy because of high temperature operation. To achieve enzymatic production of calcium-stearate at unfavorable conditions, i.e., pH 10 and 60 degrees C, suitable lipase was selected and reaction conditions were optimized using calcium hydroxide and hydrogenated beef tallow as substrates. Under optimum conditions, 95% of beef tallow, in 2.5 h, was converted into calcium-stearate by using commercial lipase SDL 451. Investigation of the time-course reaction revealed that fatty acid was initially produced by lipase, followed by conversion into calcium-stearate. The fatty acid production rate was faster than that of the conversion into calcium-stearate at the beginning of the reaction. Alkaline pH, originating from the addition of calcium hydroxide, increased the converting reaction. This is the first report demonstrating that chemical production of calcium-stearate can be replaced by enzymatic reaction, thereby creating a cleaner process.

  17. Hydroxide depletion in dilute supernates stored in waste tanks

    Energy Technology Data Exchange (ETDEWEB)

    Hobbs, D.T.

    1985-10-10

    Free hydroxide ion in dilute supernates are depleted by reaction with atmospheric carbon dioxide to form bicarbonate and carbonate species and by reaction with acidic compounds formed by the radiolytic decomposition of tetraphenylborate salts. A model of the kinetics and thermodynamics of absorption of carbon dioxide in the waste tanks has been developed. Forecasts of the rate of hydroxide depletion and the requirements for sodium hydroxide to maintain technical standards have been made for the washed sludge and washed precipitate storage tanks. Hydroxide depletion is predicted to have a minimal impact on sludge processing operations. However, in-tank precipitation and downstream DWPF operations are predicted to be significantly affected by hydroxide depletion in Tank 49H. The installation of a carbon dioxide scrubber on Tank 49H may be justified in view of the decrease in alkali content and variation in the melter feed.

  18. Effect of substrate nature on the electrochemical deposition of calcium-deficient hydroxyapatites

    Science.gov (United States)

    Gualdrón-Reyes, A. F.; Domínguez-Vélez, V.; Morales-Morales, J. A.; Cabanzo, R.; Meléndez, A. M.

    2017-01-01

    Calcium phosphates were obtained by reducing nitrate ions to produce hydroxide ions on TiO2/stainless steel and TiO2/titanium electrodes. TiO2 coatings on metallic substrates were prepared by sol-gel dip-coating method. The morphology of deposits was observed by FESEM. Chemical nature of calcium phosphate deposits was identified by Raman micro-spectroscopy and FESEM/EDS microanalysis. Electrochemical behavior of nitrate and nitrite reduction on stainless steel and titanium electrodes was studied by linear sweep voltammetry. In addition, voltammetric study of the calcium phosphate electrodeposition on both electrodes was performed. From these measurements was selected the potential to form a calcium phosphate. A catalytic current associated to nitrate reduction reaction was obtained for stainless steel electrode, leading to significant deposition of calcium phosphate. Ca/P ratio for both substrates was less than 1.67. The formation of calcium deficient hydroxyapatite was confirmed by Raman spectroscopy.

  19. Elimination of intracanal infection in dogs' teeth with induced periapical lesions after rotary instrumentation: influence of different calcium hydroxide pastes Eliminação da infecção intracanal em dentes de cães com lesões periapicais induzidas após instrumentação automatizada: influência de diferentes pastas de hidróxido de cálcio

    Directory of Open Access Journals (Sweden)

    Janir Alves Soares

    2006-06-01

    Full Text Available The aim of this study was to evaluate the antiseptic efficacy of rotary instrumentation associated with calcium hydroxide-based pastes prepared with different vehicles and antiseptics. Chronic periapical lesions were experimentally induced in 72 premolar root canals of four dogs. Under controlled asepsis, after initial microbiological sampling (A1, the root canals were instrumented using the ProFile system in conjunction with 5.25% sodium hypochlorite and the intracanal medication was placed. Four experimental groups were formed according to the pastes used: group 1- Calen (n=18, group 2- Calen+CPMC (n=20, group 3- Ca(OH2 p.a.+ anaesthetic solution (n=16 and group 4- Ca(OH2 p.a.+ 2% chlorhexidine digluconate (n=18. After 21 days, the pastes were removed; the canals were emptied and 96 hours later a second microbiological sample was obtained (A2. The incidence of positive microbiological cultures and the number of cfus in stages A1 and A2 were compared statistically by the Wilcoxon test while the influence of the different treatments in intracanal infection was evaluated by Kruskal-Wallis test at 5% significance level (pO objetivo deste estudo foi avaliar a eficácia anti-séptica da instrumentação rotatória associada às pastas à base de hidróxido de cálcio [Ca(OH2] contendo diferentes veículos e anti-sépticos. Lesões periapicais crônicas foram experimentalmente induzidas em 72 canais radiculares de pré-molares de 4 cães. Sob controlada assepsia, após amostras microbiológicas iniciais (A1, fez-se a instrumentação com o sistema ProFile coadjuvado pela solução de hipoclorito de sódio a 5,25%, seguido de medicação intracanal. Em função das pastas utilizadas obtiveram-se 4 grupos: grupo 1- Calen (n=18, grupo 2- Calen+PMCC (n=20, grupo 3- Ca(OH2 p.a.+ solução anestésica (n=16 e grupo 4- Ca(OH2 p.a.+ solução de digluconato de clorexidina a 2% (n=18. Transcorridos 21 dias, removeram-se as pastas, deixando os canais

  20. Calcium and Vitamin D

    Science.gov (United States)

    ... Cart Home › Patients › Treatment › Calcium/Vitamin D Calcium/Vitamin D Getting enough calcium and vitamin D is ... the-counter medications and calcium supplements. What is Vitamin D and What Does it Do? Vitamin D ...

  1. Imaging calcium in neurons.

    Science.gov (United States)

    Grienberger, Christine; Konnerth, Arthur

    2012-03-08

    Calcium ions generate versatile intracellular signals that control key functions in all types of neurons. Imaging calcium in neurons is particularly important because calcium signals exert their highly specific functions in well-defined cellular subcompartments. In this Primer, we briefly review the general mechanisms of neuronal calcium signaling. We then introduce the calcium imaging devices, including confocal and two-photon microscopy as well as miniaturized devices that are used in freely moving animals. We provide an overview of the classical chemical fluorescent calcium indicators and of the protein-based genetically encoded calcium indicators. Using application examples, we introduce new developments in the field, such as calcium imaging in awake, behaving animals and the use of calcium imaging for mapping single spine sensory inputs in cortical neurons in vivo. We conclude by providing an outlook on the prospects of calcium imaging for the analysis of neuronal signaling and plasticity in various animal models.

  2. Advanced phosphorus removal from membrane filtrates by adsorption on activated aluminium oxide and granulated ferric hydroxide.

    Science.gov (United States)

    Genz, Arne; Kornmüller, Anja; Jekel, Martin

    2004-09-01

    The advanced phosphorus (P) removal by adsorption was studied for its suitability as a post-treatment step for membrane bioreactor (MBR) effluents low in P concentration and particle content. Two commercial adsorbents, granulated ferric hydroxide (GFH) and activated aluminium oxide (AA), were studied in batch tests and lab-scale filter tests for P adsorption in MBR filtrates. GFH showed a higher maximum capacity for phosphate and a higher affinity at low P concentrations compared to AA. Competition by inorganic ions was negligible for both adsorbents at the original pH (8.2). When equilibrium P concentrations exceeded 2 mg L(-1) in the spiked MBR filtrates, a precipitation of calcium phosphates occurred additionally to adsorption. During column studies the effluent criteria of 50 microgL(-1) P was reached after a throughput of 8000 bed volumes for GFH and 4000 for AA. Dissolved organic carbon appears to be the strongest competitor for adsorption sites. A partial regeneration and reloading of both adsorbents could be achieved by the use of sodium hydroxide.

  3. Double layered hydroxides as potential anti-cancer drug delivery agents.

    Science.gov (United States)

    Riaz, Ufana; Ashraf, S M

    2013-04-01

    The emergence of nanotechnology has changed the scenario of the medical world by revolutionizing the diagnosis, monitoring and treatment of cancer. This nanotechnology has been proved miraculous in detecting cancer cells, delivering chemotherapeutic agents and monitoring treatment from non-specific to highly targeted killing of tumor cells. In the past few decades, a number of inorganic materials have been investigated such as calcium phosphate, gold, carbon materials, silicon oxide, iron oxide, and layered double hydroxide (LDH) for examining their efficacy in targeting drug delivery. The reason behind the selection of these inorganic materials was their versatile and unique features efficient in drug delivery, such as wide availability, rich surface functionality, good biocompatibility, potential for target delivery, and controlled release of the drug from these inorganic nanomaterials. Although, the drug-LDH hybrids are found to be quite instrumental because of their application as advanced anti-cancer drug delivery systems, there has not been much research on them. This mini review is set to highlight the advancement made in the use of layered double hydroxides (LDHs) as anti-cancer drug delivery agents. Along with the advantages of LDHs as anti-cancer drug delivery agents, the process of interaction of some of the common anti-cancer drugs with LDH has also been discussed.

  4. An Improved Blue Polymer Light-Emitting Diode by Using Sodium Hydroxide/Ca/Al Cathode

    Institute of Scientific and Technical Information of China (English)

    MA Liang; XIE Zhi-Yuan; LIU Jun; YANG Jun-Wei; CHENG Yan-Xiang; WANG Li-Xiang; WANG Fo-Song

    2005-01-01

    @@ The performance of blue polymer light-emitting diodes (PLEDs) based on poly(9,9-dioctylfluorene) (PFO) is improved by introducing a thin layer of sodium hydroxide (NaOH) between the calcium cathode and the PFO emissive layer. By replacing the commonly used Ca/Al cathode by a NaOH (2.5nm)/Ca (10 nm)/Al cathode,the driving voltage is reduced from 8.3 V to 5.4 V and the light-emitting efficiency is enhanced from 0.46cd/A to 0. 72 cd/A for achieving a luminance of 500 cd/m2, respectively. Moreover, the device with NaOH/Ca/Al cathode shows a pure blue emission of (0.17, 0. 12) at high brightnesses. These improvements are attributed to introduction of a thin layer of NaOH that can lower the interfacial barrier and facilitate electron injection.

  5. Electrochemical Properties of Nanocomposite Nanoporous Carbon / Nickel Hydroxide

    Directory of Open Access Journals (Sweden)

    O.M. Hemiy

    2016-12-01

    Full Text Available The electrochemical properties of composite nanoporous carbon / nickel hydroxide as electrode material for hybrid supercapacitors were investigated. Fast reversible faradaic reactions flow was determined in connection with chemical makeup of the -Ni(OH2/С composite. It is shown that increase of nickel hydroxide concentration can intensify reactions. It is found that clean -Ni(OH2 has 238 F/g of specific capacity, but -Ni(OH2/С nanocomposite with 90 % nickel hydroxide has 292 F/g. Such capacity value can be considered as a maximum for these composites.

  6. HYDROGEN PEROXIDE BLEACHING OF CMP PULP USING MAGNESIUM HYDROXIDE

    Directory of Open Access Journals (Sweden)

    Farhad Zeinaly

    2009-11-01

    Full Text Available Conventional bleaching of hardwood CMP pulp with magnesium hydroxide (Mg(OH2 show significant benefits over bleaching with sodium hydroxide (NaOH under various conditions. Magnesium hydroxide bleaching generate higher optical properties, higher pulp yield and lower effluent COD at the same chemical charge, but the physical properties were found to be similar for both processes. The initial freeness of the bleached pulps and refining value to reach a target freeness (about 350 ml. CSF were more for the Mg(OH2-based process. The residual peroxide of filtrate from the Mg(OH2-based process was very high as compared to conventional bleaching.

  7. Nickel hydroxide/cobalt-ferrite magnetic nanocatalyst for alcohol oxidation.

    Science.gov (United States)

    Bhat, Pooja B; Inam, Fawad; Bhat, Badekai Ramachandra

    2014-08-11

    A magnetically separable, active nickel hydroxide (Brønsted base) coated nanocobalt ferrite catalyst has been developed for oxidation of alcohols. High surface area was achieved by tuning the particle size with surfactant. The surface area of 120.94 m2 g(-1) has been achieved for the coated nanocobalt ferrite. Improved catalytic activity and selectivity were obtained by synergistic effect of transition metal hydroxide (basic hydroxide) on nanocobalt ferrite. The nanocatalyst oxidizes primary and secondary alcohols efficiently (87%) to corresponding carbonyls in good yields.

  8. Desalination and hydrogen, chlorine, and sodium hydroxide production via electrophoretic ion exchange and precipitation.

    Science.gov (United States)

    Shkolnikov, Viktor; Bahga, Supreet S; Santiago, Juan G

    2012-08-28

    We demonstrate and analyze a novel desalination method which works by electrophoretically replacing sodium and chloride in feed salt water with a pair of ions, calcium and carbonate, that react and precipitate out. The resulting calcium carbonate precipitate is benign to health, and can be filtered or settled out, yielding low ionic strength product water. The ion exchange and precipitation employs self-sharpening interfaces induced by movement of multiple ions in an electric field to prevent contamination of the product water. Simultaneously, the electrolysis associated with the electromigration produces hydrogen gas, chlorine gas, and sodium hydroxide. We conducted an experimental study of this method's basic efficacy to desalinate salt water from 100 to 600 mol m(-3) sodium chloride. We also present physicochemical models of the process, and analyze replacement reagents consumption, permeate recovery ratio, and energy consumption. We hypothesize that the precipitate can be recycled back to replacement reagents using the well-known, commercially implemented Solvay process. We show that the method's permeate recovery ratio is 58% to 46%, which is on par with that of reverse osmosis. We show that the method's energy consumption requirement over and above that necessary to generate electrolysis is 3 to 10 W h l(-1), which is on par with the energy consumed by state-of-the-art desalination methods. Furthermore, the method operates at ambient temperature and pressure, and uses no specialized membranes. The process may be feasible as a part of a desalination-co-generation facility: generating fresh water, hydrogen and chlorine gas, and sodium hydroxide.

  9. Homogeneous Precipitation of Nickel Hydroxide Powders

    Energy Technology Data Exchange (ETDEWEB)

    Bora Mavis

    2003-12-12

    Precipitation and characterization of nickel hydroxide powders were investigated. A comprehensive precipitation model incorporating the metal ion hydrolysis, complexation and precipitation reactions was developed for the production of the powders with urea precipitation method. Model predictions on Ni{sup 2+} precipitation rate were confirmed with precipitation experiments carried out at 90 C. Experimental data and model predictions were in remarkable agreement. Uncertainty in the solubility product data of nickel hydroxides was found to be the large contributor to the error. There were demonstrable compositional variations across the particle cross-sections and the growth mechanism was determined to be the aggregation of primary crystallites. This implied that there is a change in the intercalate chemistry of the primary crystallites with digestion time. Predicted changes in the concentrations of simple and complex ions in the solution support the proposed mechanism. The comprehensive set of hydrolysis reactions used in the model described above allows the investigation of other systems provided that accurate reaction constants are available. the fact that transition metal ions like Ni{sup 2+} form strong complexes with ammonia presents a challenge in the full recovery of the Ni{sup 2+}. On the other hand, presence of Al{sup 3+} facilitates the complete precipitation of Ni{sup 2+} in about 3 hours of digestion. A challenge in their predictive modeling studies had been the fact that simultaneous incorporation of more than one metal ion necessitates a different approach than just using the equilibrium constants of hydrolysis, complexation and precipitation reactions. Another limitation of using equilibrium constants is that the nucleation stage of digestion, which is controlled mainly by kinetics, is not fully justified. A new program released by IBM Almaden Research Center (Chemical Kinetics Simulator{trademark}, Version 1.01) lets the user change the order of

  10. Magnesium alloys and graphite wastes encapsulated in cementitious materials: Reduction of galvanic corrosion using alkali hydroxide activated blast furnace slag.

    Science.gov (United States)

    Chartier, D; Muzeau, B; Stefan, L; Sanchez-Canet, J; Monguillon, C

    2017-03-15

    Magnesium alloys and graphite from spent nuclear fuel have been stored together in La Hague plant. The packaging of these wastes is under consideration. These wastes could be mixed in a grout composed of industrially available cement (Portland, calcium aluminate…). Within the alkaline pore solution of these matrixes, magnesium alloys are imperfectly protected by a layer of Brucite resulting in a slow corrosion releasing hydrogen. As the production of this gas must be considered for the storage safety, and the quality of wasteform, it is important to select a cement matrix capable of lowering the corrosion kinetics. Many types of calcium based cements have been tested and most of them have caused strong hydrogen production when magnesium alloys and graphite are conditioned together because of galvanic corrosion. Exceptions are binders based on alkali hydroxide activated ground granulated blast furnace slag (BFS) which are presented in this article.

  11. USING COLLOIDAL LAYERED DOUBLE HYDROXIDES AS CATIONICMICROPARTICULATE COMPONENT

    Institute of Scientific and Technical Information of China (English)

    SonglinWang; WenxiaLiu

    2004-01-01

    Layered double hydroxides consisting of layers withcationic charges may be potential candidates ofcationic microparticles forming synergetic retentioneffect with anionic polyacrylamide. In this work, thelayered double hydroxides with various molar ratiosof Mg/AI were synthesized by co-precipitation ofmagnesium chloride and aluminum chloride and pep-tized by intense washing with water. The chemicalformula, particle size, Zeta potential of the layereddouble hydroxide were analyzed. It was found thatpositively charged magnesium aluminum hydroxidewith particle diameter in nanoparticle size could beprepared. The Zeta potential and particle size varywith the feed molar ratio of Mg/A1 and the peptizingprocess, respectively. The Zeta potential is also pHdependent. The retention experiments carried out onDDJ show that when used together with anionic poly-acrylamide, the positively charged colloidal doublehydroxide greatly improves the retention of reedpulps. The chemical formula, particle size and Zetapotential of the colloidal double hydroxide all affectits retention behavior.

  12. Hydrothermal synthesis of lanthanide (hydr)oxide micro/nanorods in presence of tetrabutylammonium hydroxide

    Institute of Scientific and Technical Information of China (English)

    李银艳; 徐时清

    2016-01-01

    Uniform and well-defined lanthanide hydroxide and oxide micro/nanorods Ln(OH)3(Ln=La, Pr, Sm, Eu, Gd, Er) and Gd(OH)3:Eu3+, Gd2O3:Eu3+ were successfully synthesized through a green and facile hydrothermal method. Tetrabutylammonium hydroxide (TBAH) and lanthanide nitrides were used as the hydrothermal precursors without the addition of any templates/surfactants. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and photoluminescence (PL) spectra. The result demonstrated that lanthanide hydroxide micro/nanorods with 20–80 nm in diameter and 50–450 in length were obtained. The size of the Ln(OH)3 (Ln=La, Pr, Sm, Eu, Gd, Er) rods increased with the increase of the atomic number. The size of the Gd(OH)3:Eu3+ rods decreased with the increase of pH value by modulating the amount of the TBAH solution. The as-formed product via the hydrothermal process, Gd(OH)3:Eu3+, could be transformed to Gd2O3:Eu3+ with the same morphology and a slight shrinking in size after a post annealing process. It is a facial method to synthesize photoluminescent nanomaterial of Gd2O3:Eu3+. The Gd2O3:Eu3+ microrods exhibited strong red emission corresponding to5D0→7F2 transition (610 nm) of Eu3+ under UV light excitation (257 nm).

  13. Structure and properties of porous ceramics obtained from aluminum hydroxide

    OpenAIRE

    Levkov, R.; Kulkov, Sergey Nikolaevich

    2016-01-01

    In this paper the study of porous ceramics obtained from aluminum hydroxide with gibbsite modification is presented. The dependence of porosity and mechanical characteristics of the material sintered at different temperatures was studied. It was shown that compressive strength of alumina ceramics increases by 40 times with decreasing the pore volume from 65 to 15%. It was shown that aluminum hydroxide may be used for pore formation and pore volume in the sintered ceramics can be controlled by...

  14. Hydrothermal Formation of Calcium Copper Tetrasilicate.

    Science.gov (United States)

    Johnson-McDaniel, Darrah; Comer, Sara; Kolis, Joseph W; Salguero, Tina T

    2015-12-01

    We describe the first hydrothermal synthesis of CaCuSi4 O10 as micron-scale clusters of thin platelets, distinct from morphologies generated under salt-flux or solid-state conditions. The hydrothermal reaction conditions are surprisingly specific: too cold, and instead of CaCuSi4 O10 , a porous calcium copper silicate forms; too hot, and calcium silicate (CaSiO3 ) forms. The precursors also strongly impact the course of the reaction, with the most common side product being sodium copper silicate (Na2 CuSi4 O10 ). Optimized conditions for hydrothermal CaCuSi4 O10 formation from calcium chloride, copper(II) nitrate, sodium silicate, and ammonium hydroxide are 350 °C at 3000 psi for 72 h; at longer reaction times, competitive delamination and exfoliation causes crystal fragmentation. These results illustrate that CaCuSi4 O10 is an even more unique material than previously appreciated.

  15. USING COLLOIDAL LAYERED DOUBLE HYDROXIDES AS CATIONIC MICROPARTICULATE COMPONENT

    Institute of Scientific and Technical Information of China (English)

    Songlin Wang; Wenxia Liu

    2004-01-01

    Layered double hydroxides consisting of layers with cationic charges may be potential candidates of cationic microparticles forming synergetic retention effect with anionic polyacrylamide. In this work, the layered double hydroxides with various molar ratios of Mg/Al were synthesized by co-precipitation of magnesium chloride and aluminum chloride and peptized by intense washing with water. The chemical formula, particle size, Zeta potential of the layered double hydroxide were analyzed. It was found that positively charged magnesium aluminum hydroxide with particle diameter in nanoparticle size could be prepared. The Zeta potential and particle size vary with the feed molar ratio of Mg/Al and the peptizing process, respectively. The Zeta potential is also pH dependent. The retention experiments carried out on DDJ show that when used together with anionic polyacrylamide, the positively charged colloidal double hydroxide greatly improves the retention of reed pulps. The chemical formula, particle size and Zeta potential of the colloidal double hydroxide all affect its retention behavior.

  16. Behavior of calcium silicate hydrate in aluminate solution

    Institute of Scientific and Technical Information of China (English)

    LI Xiao-bin; ZHAO Zhuo; LIU Gui-hua; ZHOU Qiu-sheng; PENG Zhi-hong

    2005-01-01

    Using calcium hydroxide and sodium silicate as starting materials, two kinds of calcium silicate hydrates, CaO · SiO2 · H2O and 2CaO · SiO2 · 1.17H2O, were hydro-thermally synthesized at 120 ℃. The reaction rule of calcium silicate hydrate in aluminate solution was investigated. The result shows that CaO · SiO2 · H2O is more stable than 2CaO · SiO2 · 1.17H2 O in aluminate solution and its stability increases with the increase of reaction temperature but decreases with the increase of caustic concentration. The reaction between calcium silicate hydrate and aluminate solution is mainly through two routes. In the first case, Al replaces partial Si in calcium silicate hydrate, meanwhile 3CaO · Al2 O3 · xSiO2 · (6-2x) H2 O (hydro-garnet) is formed and some SiO2 enters the solution. In the second case, calcium silicate hydrate can react directly with aluminate solution, forming hydro-garnet and Na2O · Al2O3 · 2SiO2 · nH2O (DSP). The desilication reaction of aluminate solution containing silicate could contribute partially to forming DSP.

  17. Influence of Ethylene Glycol on the Formation of Calcium Phosphate Nanocrystals

    Institute of Scientific and Technical Information of China (English)

    Yi ZUO; Yubao LI; Jie WEI; Yonggang YAN

    2003-01-01

    A synthesis route of using calcium hydroxide Ca(OH)2 with ethylene glycol solvent and orthophosphoric acid (H3PO4)as reagents is described. Three ratios of ethylene glycol to distilled water 1:0, 1:1 and 0:1 are used as diluting media for Ca(OH)2. Crystals of different morphology and composition are formed under weak alkaline circumstance at pH 7.0~8.0. Acicular calcium phosphate nanocrystals are prepared in pure ethylene glycol while rod-like calcium phosphate nanocrystals form in pure distilled water. The nanograde size of the former is smaller than that of the latter. Calcium-deficient apatite (CDAP) is obtained with a Ca/P molar ratio of 1.66. Therefore, it was deduced that the usage of ethylene glycol solvent could influence the formation of calcium phosphate crystal lattice.

  18. Ageing behaviour of unary hydroxides in trivalent metal salt solutions: Formation of layered double hydroxide (LDH)-like phases

    Indian Academy of Sciences (India)

    Michael Rajamathi; P Vishnu Kamath

    2000-10-01

    The hydroxides of Mg, Ni, Cu and Zn transform into layered double hydroxide (LDH)-like phases on ageing in solutions of Al or Cr salts. This reaction is similar to acid leaching and proceeds by a dissolution–reprecipitation mechanism offering a simple method of LDH synthesis, with implications for the accepted theories of formation of LDH minerals in the earth’s crust.

  19. The Effects of Aluminium Hydroxide and Magnesium Hydroxide on the Mechanical Properties of Thermoplastic Polyurethane Materials

    Directory of Open Access Journals (Sweden)

    Erkin Akdoğan

    2015-12-01

    Full Text Available Thermoplastic polyurethane materials are widely used in automotive, clothing, electrical and electronics, medical, construction, machine industry due to excellent physical and chemical properties. Thermoplastic polyurethane materials combustion and resistance to high temperature characteristics are poor. Additives and fillers are added into the polyurethane matrix to improve those properties. Particularly adding these agents as a flame retardant are affect mechanical properties of polyurethane materials. Therefore, it is important to determinate the mechanical properties of these materials. In this study, 5% by weight of the thermoplastic polyurethane material, aluminium tri hydroxide (ATH, (Al2O3 3H2O and magnesium hydroxide (MgOH, (Mg(OH2 were added. Ammonium polyphosphate (APP as an intumescent flame retardant with inorganic flame retardants were added to increase the flame resistance of produced composite structure. Tensile test, tear test, hardness and Izod impact tests were made and compared of those produced composites. As a result of experiments the addition of ATH has lowered the tensile strength and tear strength contrast to this the addition of MgOH has improved those properties. Hardness and Izod impact test results were showed that both of the additives have no negative effect.

  20. Calcium and Mitosis

    Science.gov (United States)

    Hepler, P.

    1983-01-01

    Although the mechanism of calcium regulation is not understood, there is evidence that calcium plays a role in mitosis. Experiments conducted show that: (1) the spindle apparatus contains a highly developed membrane system that has many characteristics of sarcoplasmic reticulum of muscle; (2) this membrane system contains calcium; and (3) there are ionic fluxes occurring during mitosis which can be seen by a variety of fluorescence probes. Whether the process of mitosis can be modulated by experimentally modulating calcium is discussed.

  1. Calcium - Function and effects

    NARCIS (Netherlands)

    Liang, Jianfen; He, Yifan; Gao, Qian; Wang, Xuan; Nout, M.J.R.

    2016-01-01

    Rice is the primary food source for more than half of the world population. Levels of calcium contents and inhibitor - phytic acid are summarized in this chapter. Phytic acid has a very strong chelating ability and it is the main inhibit factor for calcium in rice products. Calcium contents in br

  2. Preparation and mechanical property of core-shell type chitosan/calcium phosphate composite fiber

    Energy Technology Data Exchange (ETDEWEB)

    Matsuda, Atsushi [Japan Society for the Promotion of Science, Ikenohata1-1-1, Daitou-ku, Tokyo 110-0008 (Japan) and Creative Research Initiative ' Sousei' , Hokkaido University, Sapporo, Hokkaido 001-0021 (Japan)]. E-mail: MATSUDA.Atsushi@nims.go.jp; Ikoma, Toshiyuki [Biomaterials Research Center, National Institute for Materials Science, Namiki 1-1, Tsukuba, Ibaraki 305-0044 (Japan); Kobayashi, Hisatoshi [Biomaterials Research Center, National Institute for Materials Science, Namiki 1-1, Tsukuba, Ibaraki 305-0044 (Japan)]. E-mail: Kobayashi.Hisatoshi@nims.go.jp; Tanaka, Junzo [Creative Research Initiative ' Sousei' , Hokkaido University, Sapporo, Hokkaido 001-0021 (Japan); Biomaterials Research Center, National Institute for Materials Science, Namiki 1-1, Tsukuba, Ibaraki 305-0044 (Japan)

    2004-12-01

    Core-shell type chitosan/calcium phosphate composite fibers were prepared by a facile wet spinning method; the chitosan aqueous solution with PO{sub 4} ions was dropped and coagulated in the ethanol/calcium hydroxide solutions at different mixed ratio. X-ray diffraction (XRD) patterns indicated that the crystal phases of calcium phosphates in the composite fibers were a low-crystalline hydroxyapatite (HAp; Ca{sub 10}(PO{sub 4}){sub 6}(OH){sub 2})or the low-crystalline hydroxyapatite/brushite mixture depended on the ratio of ethanol/calcium hydroxide solutions. The inorganic contents were ca. 60 wt.% by using the TG-DTA analysis. The energy-dispersive X-ray spectroscopy (EDS) analysis indicated that Ca and P atoms were mainly distributed on the outer layer of the composite fiber to grow calcium phosphate crystals; however, a little amount of P atom still remained at the inside of the fiber. This indicated that the composite fibers formed a unique core-shell structure with shell of calcium phosphate and core of chitosan. The mechanical property of the fibers was reinforced by the initial concentration of chitosan solution.

  3. Comparison of particle morphology between commercial- and research-grade calcium hydroxide in endodontics.

    Science.gov (United States)

    Komabayashi, Takashi; Ahn, Chul; Spears, Robert; Zhu, Qiang

    2014-09-01

    Ca(OH)2 aqueous slurry is widely used as an inter-appointment antimicrobial dressing in root canal treatment. The aim of this study was to quantify the particle size and shape of commercial-grade UltraCal XS (UC) and to compare it with that of research-grade Ca(OH)2 (RG) using a flow particle image analyzer (FPIA). The morphology and penetration inside the dentin tubules of the UC and RG particles were examined using a scanning electron microscope (SEM). UC and RG (10 mg) were mixed with 15 mL of alcohol, and were sonicated. Five milliliters of the dispersion was subjected to FPIA, and particle length, width, perimeter and aspect ratio were analyzed. In addition, UC paste and RG aqueous slurry were agitated on dentin discs and were prepared for SEM examination. There were significant differences between UC and RG with regard to the frequency of different length groups (P < 0.0001). UC contained smaller particles than RG (P < 0.0001). Under SEM, the agitated UC and RG particles occluded the opening of dentin tubules and penetrated inside the dentin tubules. The size of UC particles is smaller than those of RG. Both UC and RG particles were able to penetrate into open dentin tubules.

  4. Analysis of the effectiveness of calcium hydroxide removal with variation of technique and solvent vehicles

    Directory of Open Access Journals (Sweden)

    Paula Dias Lins

    2015-01-01

    Conclusion: None of the removal techniques employed in this study was able to completely remove Ca(OH2 from the root canal. However, the use of distilled water as a vehicle and ultrasonic removal presented the best performance.

  5. Interactions between nanostructured calcium hydroxide and acrylate copolymers: implications in cultural heritage conservation.

    Science.gov (United States)

    Carretti, Emiliano; Chelazzi, David; Rocchigiani, Giulia; Baglioni, Piero; Poggi, Giovanna; Dei, Luigi

    2013-08-06

    The interactions between an acrylic copolymer, poly ethylmethacrylate/methylacrylate (70:30) (Poly(EMA/MA), and Ca(OH)2 nanoparticles were investigated in order to establish the reciprocal influence of these two compounds on their peculiar properties. The carbonation kinetics of Ca(OH)2 nanoparticles by atmospheric CO2 was investigated by FTIR and SEM measurements and compared to that of a nanocomposite film. CaCO3 formation occurred even in the presence of the copolymer, but only after an induction period of ca. 200 h and with a lower reaction rate. Some implications in cultural heritage conservation dealing with application of nanolime on artifacts previously treated with acrylic copolymers were discussed. Contact angle measurements, mechanical cohesion properties, and water vapor permeability allowed us to conclude that the optimum behavior of nanolime with respect to transpiration was not compromised by the presence of the copolymer, and the behavior in terms of mechanical properties recovery by the application of Ca(OH)2 nanoparticles remained excellent even in the presence of poly(EMA/MA).

  6. Biocompatibility and biomineralization assessment of bioceramic-, epoxy-, and calcium hydroxide-based sealers.

    Science.gov (United States)

    Bueno, Carlos Roberto Emerenciano; Valentim, Diego; Marques, Vanessa Abreu Sanches; Gomes-Filho, João Eduardo; Cintra, Luciano Tavares Angelo; Jacinto, Rogério Castilho; Dezan-Junior, Eloi

    2016-06-14

    Obturation of the root canal system aims to fill empty spaces, promoting hermetic sealing and preventing bacterial activity in periapical tissues. This should provide optimal conditions for repair, stimulating the process of biomineralization. An endodontic sealer should be biocompatible once it is in direct contact with periapical tissues. The aim of this study was to evaluate the rat subcutaneous tissue response to implanted polyethylene tubes filled with Smartpaste Bio, Acroseal, and Sealapex and investigate mineralization ability of these endodontic sealers. Forty Wistar rats were assigned to the three sealers groups and control group, (n = 10 animals/group) and received subcutaneous implants containing the test sealers, and the control group were implanted with empty tubes. After days 7, 15, 30, and 60, animals were euthanized and polyethylene tubes were removed with the surrounding tissues. Inflammatory infiltrate and thickness of the fibrous capsule were histologically evaluated. Mineralization was analyzed by Von Kossa staining and polarized light. Data were tabulated and analyzed via Kruskal-Wallis and Dunn's test. All tested materials induced a moderate inflammatory reaction in the initial periods. Smartpaste Bio induced the mildest inflammatory reactions after day 15. No difference was observed among groups after days 30 or 60. Von Kossa-positive staining and birefringent structures observed under polarized light revealed a larger mineralization area in Sealapex-treated animals followed by Smartpaste Bio-treated animals. At the end of the experiment, all tested sealers were found to be biocompatible. All sealers induced biomineralization, except Acroseal, which induced a mild tissue reaction.

  7. Low temperature calcium hydroxide treatment enhances anaerobic methane production from (extruded) biomass.

    Science.gov (United States)

    Khor, Way Cern; Rabaey, Korneel; Vervaeren, Han

    2015-01-01

    Ca(OH)2 treatment was applied to enhance methane yield. Different alkali concentration, incubation temperature and duration were evaluated for their effect on methane production and COD conversion efficiency from (non-)extruded biomass during mesophilic anaerobic digestion at lab-scale. An optimum Ca(OH)2 pretreatment for grass is found at 7.5% lime loading at 10°C for 20h (37.3% surplus), while mild (50°C) and high temperatures perform sub-optimal. Ca(OH)2 post-treatment after fast extrusion gives an additional surplus compared to extruded material of 15.2% (grass), 11.2% (maize straw) and 8.2% (sprout stem) regarding methane production. COD conversion improves accordingly, with additional improvements of 10.3% (grass), 9.0% (maize straw) and 6.8% (sprout stem) by Ca(OH)2 post-treatment. Therefore, Ca(OH)2 pretreatment and post-treatment at low temperature generate an additional effect regarding methane production and COD conversion efficiency. Fast extrusion gives a higher energy efficiency ratio compared to slow extrusion.

  8. Antimicrobial action of calcium hydroxide-based endodontic sealers after setting, against E. faecalis biofilm

    Directory of Open Access Journals (Sweden)

    Gabriely Cristinni REZENDE

    2016-01-01

    Full Text Available Abstract Enterococcus faecalis are gram positive bacteria that can mostly resist endodontic therapy, inducing persistent infection in the root canal system. Endodontic sealers with antimicrobial activity may help eliminate residual microorganisms that survive endodontic treatment. The present study aimed at comparing the antimicrobial activity of Acroseal, Sealapex and AH Plus endodontic sealers in an in vitro biofilm model. Bovine dentin specimens (144 were prepared, and twelve blocks for each sealer and each experimental time point (2, 7 and 14 days were placed and left in contact with plates containing inoculum of E. faecalis (ATCC 51299, to induce biofilm formation. After 14 days, the samples were transferred to another plate with test sealers and kept at 37°C and 5% CO2 for 2, 7 and 14 days. The specimens without sealers were used as a control for each period. The samples were agitated in a sonicator after each experiment. The suspensions were agitated in a vortex mixer, serially diluted in saline, and triple plated onto m-Enterococcus agar. Colonyforming units were counted, and the data were statistically analyzed using ANOVA, Shapiro-Wilk and Kruskal-Wallis one-way tests (p < 0.05 to determine antimicrobial potential. Sealapex showed significant differences at all the experimental time points, in comparison with all the other groups. AH Plus and Acroseal showed antimicrobial activity only on the 14th experimental day. Neither of the sealers tested were able to completely eliminate the biofilm. Sealapex showed the highest antimicrobial activity in all the experimental periods. The antimicrobial activity of all the sealers analyzed increased over time.

  9. Efficacy of a combined nanoparticulate/calcium hydroxide root canal medication on elimination of Enterococcus faecalis.

    Science.gov (United States)

    Javidi, Maryam; Afkhami, Farzaneh; Zarei, Mina; Ghazvini, Kiarash; Rajabi, Omid

    2014-08-01

    The purpose of this study was to evaluate the efficacy of Ca(OH)2 with or without a silver nanoparticle suspension to eliminate Enterococcus faecalis from root canals. A total of 66 extracted human single-rooted teeth contaminated with E. faecalis were treated with 10% Ca(OH)2 alone, Ca(OH)2 with nanosilver or sterile water (as a negative control). Samples were obtained with paper points and Gates-Glidden burs at 1 and 7 days after root canal preparation and the number of colony-forming units (CFU) was determined. The number of CFUs observed after dressing with Ca(OH)2  + nanosilver was significantly less than the number observed with Ca(OH)2 alone after 1 or 7 days (P  0.05). Higher antimicrobial efficacy was observed in the Ca(OH)2 group after 7 days than 1 day (P < 0.001). This study highlighted the potential advantage of using a mixture of Ca(OH)2 and nanosilver for intracanal medicament.

  10. Calcium signaling and epilepsy.

    Science.gov (United States)

    Steinlein, Ortrud K

    2014-08-01

    Calcium signaling is involved in a multitude of physiological and pathophysiological mechanisms. Over the last decade, it has been increasingly recognized as an important factor in epileptogenesis, and it is becoming obvious that the excess synchronization of neurons that is characteristic for seizures can be linked to various calcium signaling pathways. These include immediate effects on membrane excitability by calcium influx through ion channels as well as delayed mechanisms that act through G-protein coupled pathways. Calcium signaling is able to cause hyperexcitability either by direct modulation of neuronal activity or indirectly through calcium-dependent gliotransmission. Furthermore, feedback mechanisms between mitochondrial calcium signaling and reactive oxygen species are able to cause neuronal cell death and seizures. Unravelling the complexity of calcium signaling in epileptogenesis is a daunting task, but it includes the promise to uncover formerly unknown targets for the development of new antiepileptic drugs.

  11. Photo-oxidation of EPDM/layered double hydroxides composites: Influence of layered hydroxides and stabilizers

    Directory of Open Access Journals (Sweden)

    2007-11-01

    Full Text Available The photo-oxidation of ethylene propylene diene monomer (EPDM/ layered double hydroxide (LDH composites as well as EPDM/LDH with stabilizers is studied under accelerated UV irradiation (λ≥290 nm at 60°C for different time intervals. The development of functional groups during oxidation was monitored by FT-IR spectroscopy. The photodegradation of the pristine polymer and composites take place and the increase in hydroxyl and carbonyl groups with irradiation times, was estimated. EPDM filled LDH showed higher degradation rate than pristine EPDM, while in acidic medium EPDM/LDH showed almost equal degradation as in isolated conditions. These results show the advantages of LDHs as a filler as well as an acid killer. The effect of stabilizers is very less because of their concentration in comparison of LDH.

  12. Structure and properties of porous ceramics obtained from aluminum hydroxide

    Science.gov (United States)

    Levkov, R.; Kulkov, S.

    2016-08-01

    In this paper the study of porous ceramics obtained from aluminum hydroxide with gibbsite modification is presented. The dependence of porosity and mechanical characteristics of the material sintered at different temperatures was studied. It was shown that compressive strength of alumina ceramics increases by 40 times with decreasing the pore volume from 65 to 15%. It was shown that aluminum hydroxide may be used for pore formation and pore volume in the sintered ceramics can be controlled by varying the aluminum hydroxide concentration and sintering temperature. Based on these results one can conclude that the obtained structure is very close to inorganic bone matrix and can be used as promising material for bone implants production.

  13. CRACK2. Modelling calcium carbonate deposition from bicarbonate solutions in cracks in concrete

    DEFF Research Database (Denmark)

    Brodersen, Knud Erik

    2003-01-01

    The numerical CRACK2 model simulates precipitation of calcite from calcium bicarbonate solution (e.g. groundwater) passing through cracks in concrete or other cementitious materials. A summary of experimental work is followed by a detailed description ofthe model. Hydroxyl ions are transported...... by diffusion in pore systems in columns of cementitious materials. The hydroxyl is precipitating calcite from a flow of bicarbonate solution in a crack connecting the ends of a row of such columns. Thecementitious material is simulated as calcium hydroxide mixed with inert material but with sodium hydroxide...... dissolved in the pore solution. Diffusive migration of cesium as radioactive isotope is also considered. Electrical interaction of the migratingions is taken into account. Example calculations demonstrate effects of parameter variations on distribution of precipitated calcite in the crack...

  14. Oxidative leaching of chromium from layered double hydroxides: Mechanistic studies

    Indian Academy of Sciences (India)

    A V Radha; P Vishnu Kamath

    2004-08-01

    The layered double hydroxide (LDH) of Zn with Cr on treatment with a hypochlorite solution releases chromate ions as a result of oxidative leaching by a dissolution–reprecipitation mechanism. The residue is found to be -Zn(OH)2. The LDH of Mg with Cr on the other hand is resistant to oxidative leaching. In contrast, a X-ray amorphous gel of the coprecipitated hydroxides of Mg and Cr yields chromate ions. These results suggest that the oxidation potential of Cr(III) in LDHs is determined by the nature of the divalent ion and the crystallinity of the phase while being unaffected by the nature of the intercalated anions.

  15. Calcium is important forus.

    Institute of Scientific and Technical Information of China (English)

    高利平

    2005-01-01

    Calcium is important for our health.We must have it in our diet to stay well.A good place to get it is from dairy products like milk, cheese and ice cream.One pound of cheese has fifty times the calcium we should have every day.Other foods have less.For example,a pound of beans also has calcium.But it has only three times the amount we ought to have daily.

  16. Preparation of calcium stannate by modified wet chemical method

    Institute of Scientific and Technical Information of China (English)

    何则强; 李新海; 刘恩辉; 侯朝辉; 邓凌峰; 胡传跃

    2003-01-01

    A modified wet chemical route for low-temperature synthesis of the calcium stannate CaSnO3, a potentialmaterial for dielectric applications is reported. Firstly, a precursor CaSn(OH)6 was prepared using tin tetrachloride,calcium chloride and sodium hydroxide at room temperature. Then the precursor was annealed at relatively low tem-perature of 600 ℃ to obtain CaSnO3. The phase identification, thermal behavior and surface morphology of the sam-ples were characterized by element analysis, X-ray diffraction (XRD), thermo-gravimetric (TG) analysis and deriva-tive thermo-gravimetric (DTG) analysis, Fourier transform infrared spectroscopy (FTIR) and scanning electron mi-croscopy (SEM) in detail. The results show that CaSnO3 obtained by this method possesses a cubic perovskitestructure with average grain size of 5 μm.

  17. Evaluation of Calcium Phosphate Cement As a Root Canal Sealer Filling Material

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Calcium phosphate cement for root end sealing was obtained by mixing α-tricalcium phosphate and additives with an aqueous solution of citric. Powder and liquid were mixed at a ratio of 1.25g/mL. The biocompatibility of this material was investigated primarily by subcutaneous implantation tests. Then calcium phosphate cement was used to fill three adult dogs' root canal, both calcium hydroxide paste and hydroxyapatite paste as control. The animals were killed at 4,12,20 weeks postoperatively respectively. The effects of different materials on the apical closure, restoration of periapical tissues and adaptability to the dentinal surface were examined by optical and electronic microscope. The observation at 20 weeks shows that the calcium phosphate cement has the potentialities of being a root canal sealer filling material available for pulpless teeth with open-apex and destructive periapical tissue.

  18. From Zn-Al layered double hydroxide to ZnO nanostructure:Gradually etching by sodium hydroxide

    Institute of Scientific and Technical Information of China (English)

    Gang Qiang Wan; Dong Xiang Li; Chun Fang Li; Jie Xu; Wan Guo Hou

    2012-01-01

    Zn-Al layered double hydroxide (LDH) was used as precursor to produce ZnO nanostructures through dissolution of aluminum hydroxide in caustic soda.The Zn-Al LDH could transform into different nanostructures of ZnO on LDH nanosheets and even pure ZnO nanorods under various NaOH concentration.The formed ZnO nanorods vertically aligned on both LDH sides.UV-vis diverse reflectance spectra show that the obtained ZnO nanorods have a band gap of approximately 3.05 eV.Such ZnO/LDH nanostructures might be used as photocatalyst in the organic pollutant decomposition.

  19. Recent progress in polymer/layered double hydroxide nanocomposites

    Institute of Scientific and Technical Information of China (English)

    DING Peng; CHEN Wei; QU Baojun

    2006-01-01

    New developments in the studies of nanocomposites based on polymer matrixes and layered double hydroxides (LDHs)in recent years are reviewed combining our relative research work, among which the synthesis techniques, the physicochemical characterizations, and the improved material properties are especially discussed. The possible application of polymer/LDH nanocomposites is also proposed.

  20. Sorptive stabilization of organic matter by amorphous Al hydroxide

    NARCIS (Netherlands)

    M.P.W. Schneider; T. Scheel; R. Mikutta; P. van Hees; K. Kaiser; K. Kalbitz

    2010-01-01

    Amorphous Al hydroxides (am-Al(OH)(3)) strongly sorb and by this means likely protect dissolved organic matter (OM) against microbial decay in soils. We carried out batch sorption experiments (pH 4.5; 40 mg organic C L-1) with OM extracted from organic horizons under a Norway spruce and a European b

  1. Dewatering of alumino-humic sludge: impacts of hydroxide.

    Science.gov (United States)

    Bache, D H; Papavasilopoulos, E N

    2003-08-01

    The paper draws together information on factors which influence the conditioning and dewatering behaviour of an alum sludge gained from the coagulation of a low-turbidity coloured water. A principal focus is the potential impact of aluminium hydroxide on the sludge character. Background information is provided on the composition of the source floc for the domain pH 6.0-6.5 and Al>2.0mg/l. From this, there were many pointers to the presence of Al(OH)(3)(s) within the floc. A series of comparisons were made between an alum sludge and a hydroxide suspension at a concentration equivalent to the coagulant fraction within the sludge. The parameters studied included floc size, floc density, polymer adsorption and dewatering behaviour at different time-scales. In all cases, there were strong similarities in the behaviour of the two suspensions-indicating the potential impact of the hydroxide. There was also evidence of common features being displayed by both the organic fractions and the hydroxide. It was suggested that some of the behavioural features might emanate from a common fractal structure within the source floc, the fractal dimension (approximately 1) being insensitive to composition.

  2. 21 CFR 73.1010 - Alumina (dried aluminum hydroxide).

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Alumina (dried aluminum hydroxide). 73.1010 Section 73.1010 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1010 Alumina (dried...

  3. DOUBLE SHELL TANK (DST) HYDROXIDE DEPLETION MODEL FOR CARBON DIOXIDE ABSORPTION

    Energy Technology Data Exchange (ETDEWEB)

    OGDEN DM; KIRCH NW

    2007-10-31

    This document generates a supernatant hydroxide ion depletion model based on mechanistic principles. The carbon dioxide absorption mechanistic model is developed in this report. The report also benchmarks the model against historical tank supernatant hydroxide data and vapor space carbon dioxide data. A comparison of the newly generated mechanistic model with previously applied empirical hydroxide depletion equations is also performed.

  4. 高分散性片状阻燃型氢氧化镁的制备%Synthesis of Flaky Flame-retardant Magnesium Hydroxide with High Dispersion

    Institute of Scientific and Technical Information of China (English)

    吴智诚; 潘丹梅; 陈志; 林璋

    2012-01-01

    hydroxide hexagonal flake increased to 80- 100 nm after hydro- thermal reaction. Moreover, the dispersion of the product was enhanced and the aggregation was reduced after further surface modification and regulation by dispersant. Thus, the specific surface area was 9.1668 m^2/g. When the modified highly dispersed magnesium hydroxide was added to the PVC composite system, the oxygen index of the system was 27.3. Under the same condition, the oxygen index of ordinary magnesium hydroxide and calcium carbonate were 25.7 and 22.7, respectively. This result declared that the addition of highly dispersed magnesium hydroxide could enhance the flame retardancy of PVC composite system.

  5. Synthesis and reaction behavior of calcium silicate hydrate in basic system

    Institute of Scientific and Technical Information of China (English)

    刘桂华; 贺强; 李小斌; 彭志宏; 周秋生

    2004-01-01

    At the molar ratio of CaO to SiO2 of 1, with calcium hydroxide and sodium silicate, calcium silicate hydrate was synthesized at 50, 100, 170 ℃, respectively. The results show that temperature favors the formation of calcium silicate hydrate with perfect structure. When calcium silicate hydrate reacts with caustic solution, the decomposition rate of calcium silicate hydrate increases with the increasing caustic concentration and decreases with the raising synthesis temperature and the prolongation of reaction time. The decomposition rate is all less than 1.2 % in caustic solution, and XRD pattern of the residue after reaction with caustic solution is found as the same as that of original calcium silicate hydrate, which indicates the stable existence of calcium silicate hydrate in caustic solution.When reacted with soda solution, the decomposition rate increases with the increasing soda concentration and reaction time, while decreases with the synthesis temperature. The decomposition rate is more than 2% because CaO · SiO2 · H2O(CSH( Ⅰ )), except Ca5 (OH)2Si6O16 · 4H2O and Ca6Si6O17 (OH)2, is decomposed. So the synthesis temperature and soda concentration should be controlled in the process of transformation of sodium aluminosilicate hydrate into calcium silicate hydrate.

  6. Acidosis and Urinary Calcium Excretion

    DEFF Research Database (Denmark)

    Alexander, R Todd; Cordat, Emmanuelle; Chambrey, Régine

    2016-01-01

    Metabolic acidosis is associated with increased urinary calcium excretion and related sequelae, including nephrocalcinosis and nephrolithiasis. The increased urinary calcium excretion induced by metabolic acidosis predominantly results from increased mobilization of calcium out of bone and inhibi...

  7. Calcium signaling in neurodegeneration

    Directory of Open Access Journals (Sweden)

    Dreses-Werringloer Ute

    2009-05-01

    Full Text Available Abstract Calcium is a key signaling ion involved in many different intracellular and extracellular processes ranging from synaptic activity to cell-cell communication and adhesion. The exact definition at the molecular level of the versatility of this ion has made overwhelming progress in the past several years and has been extensively reviewed. In the brain, calcium is fundamental in the control of synaptic activity and memory formation, a process that leads to the activation of specific calcium-dependent signal transduction pathways and implicates key protein effectors, such as CaMKs, MAPK/ERKs, and CREB. Properly controlled homeostasis of calcium signaling not only supports normal brain physiology but also maintains neuronal integrity and long-term cell survival. Emerging knowledge indicates that calcium homeostasis is not only critical for cell physiology and health, but also, when deregulated, can lead to neurodegeneration via complex and diverse mechanisms involved in selective neuronal impairments and death. The identification of several modulators of calcium homeostasis, such as presenilins and CALHM1, as potential factors involved in the pathogenesis of Alzheimer's disease, provides strong support for a role of calcium in neurodegeneration. These observations represent an important step towards understanding the molecular mechanisms of calcium signaling disturbances observed in different brain diseases such as Alzheimer's, Parkinson's, and Huntington's diseases.

  8. In vitro studies of calcium phosphate silicate bone cements.

    Science.gov (United States)

    Zhou, Shuxin; Ma, Jingzhi; Shen, Ya; Haapasalo, Markus; Ruse, N Dorin; Yang, Quanzu; Troczynski, Tom

    2013-02-01

    A novel calcium phosphate silicate bone cement (CPSC) was synthesized in a process, in which nanocomposite forms in situ between calcium silicate hydrate (C-S-H) gel and hydroxyapatite (HAP). The cement powder consists of tricalcium silicate (C(3)S) and calcium phosphate monobasic (CPM). During cement setting, C(3)S hydrates to produce C-S-H and calcium hydroxide (CH); CPM reacts with the CH to precipitate HAP in situ within C-S-H. This process, largely removing CH from the set cement, enhances its biocompatibility and bioactivity. The testing results of cell culture confirmed that the biocompatibility of CPSC was improved as compared to pure C(3)S. The results of XRD and SEM characterizations showed that CPSC paste induced formation of HAP layer after immersion in simulated body fluid for 7 days, suggesting that CPSC was bioactive in vitro. CPSC cement, which has good biocompatibility and low/no cytotoxicity, could be a promising candidate as biomedical cement.

  9. Thermal stability and oil absorption of aluminum hydroxide treated by dry modification with phosphoric acid

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The dry modification of aluminum hydroxide powders with phosphoric acid and the effects of modification of technological conditions on thermal stability, morphology and oil absorption of aluminum hydroxide powders were investigated. The results show that the increase of mass ratio of phosphoric acid to aluminum hydroxide, the decrease of mass concentration of phosphoric acid and prolongation of mixing time are favorable to the improvement of thermal stability of aluminum hydroxide; when the mass ratio of phosphoric acid to aluminum hydroxide is 5:100, the mass concentration of phosphoric acid is 200 g/L and the mixing time is 10 min, the initial temperature of loss of crystal water in aluminum hydroxide rises from about 192.10 to 208.66 ℃2,but the dry modification results in the appearance of agglomeration and macro-aggregate in the modified powders, and the oil absorption of modified powders becomes higher than that of original aluminum hydroxide.

  10. Immobilization of laccase on hybrid layered double hydroxide

    Directory of Open Access Journals (Sweden)

    David Isidoro Camacho Córdova

    2009-01-01

    Full Text Available Crystals of Mg/Al layered double hydroxide were synthesized by alkaline precipitation and treated in an aqueous solution of glutamic acid. The glutamate ions were not intercalated into the interlayer space, but were detected in the material by Fourier transform infrared spectroscopy, suggesting that only the external surfaces of crystals were modified with glutamate ions. The resulting hybrid material was tested as a support for immobilization of the enzyme laccase (Myceliophthora thermophila. The immobilized enzyme preparation was characterized by electronic paramagnetic resonance spectroscopy and by assays of catalytic activity. The activity of the immobilized laccase was 97% of the activity in the free enzyme. Layered double hydroxide is a suitable support for use in remediation of soil studies.

  11. Leaching kinetics of gibbsitic bauxite with sodium hydroxide

    Directory of Open Access Journals (Sweden)

    Abdel-Aal El-Sayed A.

    2016-01-01

    Full Text Available In this paper the results of a leaching kinetics study of bauxite ore with sodium hydroxide are presented. The effect of ore particle size, sodium hydroxide concentration and reaction temperature on the Al2O3 extraction rate was determined. The results obtained showed that 99% of Al2O3 was leached out using −200+270 mesh ore particle size at a reaction temperature of 105 °C for 60 min reaction time with 250 g/L NaOH. The solid-to-liquid ratio was maintained constant at 1:20. The results indicated that leaching of bauxite is the rate controlling process. The activation energy was determined to be 46.04 kJ/mole, which was characteristic for a chemically controlled process.

  12. Adsorption behavior of condensed phosphate on aluminum hydroxide

    Institute of Scientific and Technical Information of China (English)

    GUAN Xiao-hong; CHEN Guang-hao; SHANG Chii

    2007-01-01

    Sodium pyrophosphate(pyro-P,Na4P207),sodium tripolyphosphate(tripoly-P,NasP3010),and sodium hexametaphosphate(metaP,(NaP03)6)were selected as the model compounds of condensed phosphate to investigate the adsorption behavior of condensed phosphate on aluminum hydroxide.The adsorption was found to be endothermic and divisible into two stages:(1)fast adsorption within 1 h:and(2)slow adsorption between 1 and 24 h.The modified Freundlich model simulated the fast adsorption stage well;the slow adsorption stage was described well by the first-order kinetics.The activation energies of pyro-P,tripoly-P,and meta-P adsorption on aluminum hydroxide were determined to be 20.2,22.8 and 10.9 kJ/mol P adsorbed,respectively,in the fast adsorption stage and to be 66.3.53.5 and 72.5 kJ/tool P adsorbed,respectively,in the slow adsorption stage.The adsorption increased the negative charge of the aluminum hydroxide surface.Transmission electron microscopy and energy dispersive X-ray analysis analyses provided evidence that the adsorption was not uniform on the surface and that the small crystals contfibuted more to the fast adsorption than the normal sites did.The results from X-ray fluorescence spectrometry and X-ray photoelectron spectroscopy tests also revealed the uneven adsorption of condensed phosphate as a function of the penetration depth.More condensed phosphates were adsorbed on the outer surface of aluminum hydroxide than in its inner parts.

  13. Hydrothermal Synthesis of Ni/Al Layered Double Hydroxide Nanorods

    OpenAIRE

    Yun Zhao; Fenfei Xiao; Qingze Jiao

    2011-01-01

    Ni/Al layered double hydroxide (LDH) nanorods were successfully synthesized by the hydrothermal reaction. The crystal structure of the products was characterized by X-ray diffraction (XRD). The morphology of the products was observed using transmission electron microscopy (TEM) and field emission scanning electron microscopy (SEM). The influences of reaction time and pH value on the morphology of the Ni/Al LDHs were investigated. The result showed that the well-crystallized nanorods of Ni/Al ...

  14. Calcium and Your Child

    Science.gov (United States)

    ... for dinner. Create mini-pizzas by topping whole-wheat English muffins or bagels with pizza sauce, low- ... Minerals Do I Need to Drink Milk? Lactose Intolerance Becoming a Vegetarian Soy Foods and Health Calcium ...

  15. Stoichiometry of Calcium Medicines

    Science.gov (United States)

    Pinto, Gabriel

    2005-01-01

    The topic of calcium supplement and its effects on human lives is presented in the way of questions to the students. It enables the students to realize the relevance of chemistry outside the classroom surrounding.

  16. Calcium and Calcium-Base Alloys

    Science.gov (United States)

    1949-01-01

    should be satisfactory, because the electrolytic process for •(!>: A. H. Everts and G. D. Baglev’, " Physical «nrt m<„.+„4 i «_ of Calcium«, Electrochem...Rev. Metalurgie , 3j2, (1), 129 (1935). 10 ^sm^mssss^ma^^ extension between two known loads, is preferable to the value of 3,700,000 p.B.i. obtained

  17. Oxidation of Dodecanoate Intercalated Iron(II)–Iron(III) Layered Double Hydroxide to Form 2D Iron(III) (Hydr)oxide Layers

    DEFF Research Database (Denmark)

    Huang, Li‐Zhi; Ayala‐Luis, Karina B.; Fang, Liping;

    2013-01-01

    A planar trioctahedral iron(II)–iron(III) hydroxide (green rust, GR) intercalated with dodecanoate (GRC12) has been oxidized by dioxygen to produce the corresponding planar iron(III) (hydr)oxide. The formulae of GRC12 and the final iron(III) product (oxGRC12) were determined to be FeII2.00FeIII1...

  18. [Calcium suppletion for patients who use gastric acid inhibitors: calcium citrate or calcium carbonate?].

    NARCIS (Netherlands)

    Jonge, H.J. de; Gans, R.O.; Huls, G.A.

    2012-01-01

    Various calcium supplements are available for patients who have an indication for calcium suppletion. American guidelines and UpToDate recommend prescribing calcium citrate to patients who use antacids The rationale for this advice is that water-insoluble calcium carbonate needs acid for adequate ab

  19. Application of recovered magnesium hydroxide from a flue gas desulfurization system for wastewater treatment

    Energy Technology Data Exchange (ETDEWEB)

    Bishop, P.L.; Wu, Q.; Keener, T.; Zhuang, L.A.; Gurusamy, R.; Pehkonen, S.

    1999-07-01

    Magnesium hydroxide, reclaimed from the flue gas desulfurization system (FGD) at the Zimmer Power Plant, Cincinnati, Ohio, is a weak base, in the form of either a slurry or powder. It has many potential applications for wastewater treatment. The objectives of this research are (1) to characterize the reclaimed magnesium hydroxide, e.g., purity, particle size distribution, dissolution kinetics; (2) to evaluate neutralization capacity and buffering intensity of the reclaimed magnesium hydroxide; (3) to study the efficacy of the reclaimed magnesium hydroxide for nutrient removal in wastewater treatment processes; (4) to investigate whether and how the magnesium hydroxide influences the characteristics of the activated sludge floc; (5) to determine whether magnesium hydroxide improves the anaerobic sludge digestion process and associated mechanisms; and (6) to conduct a cost-benefit analysis for the application of the reclaimed magnesium hydroxide in wastewater treatment and the possibility of marketing this product. Research results to date show that the purity of the reclaimed magnesium hydroxide depends largely on the recovery hydroxide slurry. This product proved to be very effective for wastewater neutralization, compared with other commonly used chemicals, both for its neutralization capacity and its buffering intensity. Due to its relatively low solubility in water and its particle size distribution characteristics, magnesium hydroxide behaves like a weak base, which will be very beneficial for process control. The authors also found that nitrogen and phosphorus could be removed from the wastewater using magnesium hydroxide due to their complexation and precipitation as magnesium ammonium phosphate (struvite). Magnesium hydroxide also greatly enhanced the settleability of the activated sludge. Intensive research on the mechanisms associated with these phenomena reveals that sweep flocculation and magnesium ion bridging between exopolymeric substances (EPS) of

  20. Calcium in plant cells

    Directory of Open Access Journals (Sweden)

    V. V. Schwartau

    2014-04-01

    Full Text Available The paper gives the review on the role of calcium in many physiological processes of plant organisms, including growth and development, protection from pathogenic influences, response to changing environmental factors, and many other aspects of plant physiology. Initial intake of calcium ions is carried out by Ca2+-channels of plasma membrane and they are further transported by the xylem owing to auxins’ attractive ability. The level of intake and selectivity of calcium transport to ove-ground parts of the plant is controlled by a symplast. Ca2+enters to the cytoplasm of endoderm cells through calcium channels on the cortical side of Kaspary bands, and is redistributed inside the stele by the symplast, with the use of Ca2+-АТPases and Ca2+/Н+-antiports. Owing to regulated expression and activity of these calcium transporters, calclum can be selectively delivered to the xylem. Important role in supporting calcium homeostasis is given to the vacuole which is the largest depo of calcium. Regulated quantity of calcium movement through the tonoplast is provided by a number of potential-, ligand-gated active transporters and channels, like Ca2+-ATPase and Ca2+/H+ exchanger. They are actively involved in the inactivation of the calcium signal by pumping Ca2+ to the depo of cells. Calcium ATPases are high affinity pumps that efficiently transfer calcium ions against the concentration gradient in their presence in the solution in nanomolar concentrations. Calcium exchangers are low affinity, high capacity Ca2+ transporters that are effectively transporting calcium after raising its concentration in the cell cytosol through the use of protons gradients. Maintaining constant concentration and participation in the response to stimuli of different types also involves EPR, plastids, mitochondria, and cell wall. Calcium binding proteins contain several conserved sequences that provide sensitivity to changes in the concentration of Ca2+ and when you

  1. Elemental calcium intake associated with calcium acetate/calcium carbonate in the treatment of hyperphosphatemia

    OpenAIRE

    Wilson, Rosamund J; Copley, J Brian

    2017-01-01

    Background Calcium-based and non-calcium-based phosphate binders have similar efficacy in the treatment of hyperphosphatemia; however, calcium-based binders may be associated with hypercalcemia, vascular calcification, and adynamic bone disease. Scope A post hoc analysis was carried out of data from a 16-week, Phase IV study of patients with end-stage renal disease (ESRD) who switched to lanthanum carbonate monotherapy from baseline calcium acetate/calcium carbonate monotherapy. Of the intent...

  2. [Microbial geochemical calcium cycle].

    Science.gov (United States)

    Zavarzin, G A

    2002-01-01

    The participation of microorganisms in the geochemical calcium cycle is the most important factor maintaining neutral conditions on the Earth. This cycle has profound influence on the fate of inorganic carbon, and, thereby, on the removal of CO2 from the atmosphere. The major part of calcium deposits was formed in the Precambrian, when prokaryotic biosphere predominated. After that, calcium recycling based on biogenic deposition by skeletal organisms became the main process. Among prokaryotes, only a few representatives, e.g., cyanobacteria, exhibit a special calcium function. The geochemical calcium cycle is made possible by the universal features of bacteria involved in biologically mediated reactions and is determined by the activities of microbial communities. In the prokaryotic system, the calcium cycle begins with the leaching of igneous rock predominantly through the action of the community of organotrophic organisms. The release of carbon dioxide to the soil air by organotrophic aerobes leads to leaching with carbonic acid and soda salinization. Under anoxic conditions, of major importance is the organic acid production by primary anaerobes (fermentative microorganisms). Calcium carbonate is precipitated by secondary anaerobes (sulfate reducers) and to a smaller degree by methanogens. The role of the cyanobacterial community in carbonate deposition is exposed by stromatolites, which are the most common organo-sedimentary Precambrian structures. Deposition of carbonates in cyanobacterial mats as a consequence of photoassimilation of CO2 does not appear to be a significant process. It is argued that carbonates were deposited at the boundary between the "soda continent", which emerged as a result of subaerial leaching with carbonic acid, and the ocean containing Ca2+. Such ecotones provided favorable conditions for the development of the benthic cyanobacterial community, which was a precursor of stromatolites.

  3. Effect of some organic solvent-water mixtures composition on precipitated calcium carbonate in carbonation process

    Science.gov (United States)

    Konopacka-Łyskawa, Donata; Kościelska, Barbara; Karczewski, Jakub

    2015-05-01

    Precipitated calcium carbonate particles were obtained during carbonation of calcium hydroxide slurry with carbon dioxide. Aqueous solutions of isopropyl alcohol, n-butanol and glycerol were used as solvents. Concentration of organic additives in the reactive mixture was from 0% to 20% (vol). Precipitation process were performed in a stirred tank reactor equipped with gas distributor. Multimodal courses of particles size distribution were determined for produced CaCO3 particles. Calcium carbonate as calcite was precipitated in all experiments. The mean Sauter diameter of CaCO3 particles decreased when the concentration of all used organic additives increased. The amount of small particle fraction in the product increased with the increasing concentration of organic solvents. Similar physical properties of used liquid phase resulted in the similar characteristics of obtained particles.

  4. Effect of Calcium Leaching on the Properties of Cement-based Composites

    Institute of Scientific and Technical Information of China (English)

    LLIN Weiting; CHENG An; HUANG Ran; CHEN Chuntao; ZHOU Xingang

    2011-01-01

    Leaching is one of the major factors that alter the mechanical properties of cementbased composites.This study is aimed to investigate the effect of leaching on the properties of cementbased composites.Specimens with two water/cementitious ratios and two mineral admixtures were tested.An electrical potential was applied to accelerate the leaching process.Compressive strength test,scanning electronic microscopy,thermogravimetric analysis and X-ray diffraction analysis were conducted.Test results demonstrated that the calcium leaching reduced compressive strengths of concrete specimens,and such effect was prominent on the specimens without mineral admixtures.The leaching resistance increased with a decrease in water/cementitious ratio and an increase in amount of mineral admixtures.The mineral admixtures would reduce the amount of calcium hydroxide and refine the pore structure through pozzolanic reactions.A fair relationship was found between the calcium leaching and the compressive strength.

  5. Direct ethanol fuel cell using hydrotalcite clay as a hydroxide ion conductive electrolyte.

    Science.gov (United States)

    Tadanaga, Kiyoharu; Furukawa, Yoshihiro; Hayashi, Akitoshi; Tatsumisago, Masahiro

    2010-10-15

    An alkaline-type direct ethanol fuel cell (DEFC) using a natural clay electrolyte with non-platinum catalysts is proposed. So-called hydrotalcite clay, Mg–Al layered double hydroxide intercalated with CO₃²⁻, is shown to be a hydroxide ion conductor. An alkaline-type DEFC using this natural clay as the electrolyte and aqueous solution of ethanol and potassium hydroxide as a source of fuel exhibits excellent electrochemical performance from room temperature to 80 °C.

  6. Hydroxide ion concentration at an interface between concrete and a self-levelling flooring compound

    OpenAIRE

    Anderberg, Anders; Wadsö, Lars

    2007-01-01

    This article presents results from measurements of hydroxide ion transport between a concrete and a floor screed of a lower alkalinity than the concrete. As many floor coverings and floor adhesives are sensitive to high alkaline conditions it is important to know how hydroxide ions are transported to be able to evaluate the long-term function of floor constructions. It was found that only minor transport of hydroxide ions occurs in the hygroscopic moisture range. One conclusion is therefore t...

  7. Inositol trisphosphate and calcium signalling

    Science.gov (United States)

    Berridge, Michael J.

    1993-01-01

    Inositol trisphosphate is a second messenger that controls many cellular processes by generating internal calcium signals. It operates through receptors whose molecular and physiological properties closely resemble the calcium-mobilizing ryanodine receptors of muscle. This family of intracellular calcium channels displays the regenerative process of calcium-induced calcium release responsible for the complex spatiotemporal patterns of calcium waves and oscillations. Such a dynamic signalling pathway controls many cellular processes, including fertilization, cell growth, transformation, secretion, smooth muscle contraction, sensory perception and neuronal signalling.

  8. Gravimetric Determination of Calcium as Calcium Carbonate Hydrate.

    Science.gov (United States)

    Henrickson, Charles H.; Robinson, Paul R.

    1979-01-01

    The gravimetric determination of calcium as calcium carbonate is described. This experiment is suitable for undergraduate quantitative analysis laboratories. It is less expensive than determination of chloride as silver chloride. (BB)

  9. Calcium and Calcium Supplements: Achieving the Right Balance

    Science.gov (United States)

    ... bone mass, which is a risk factor for osteoporosis. Many Americans don't get enough calcium in their diets. Children and adolescent girls are at particular risk, but so are adults age 50 and older. How much calcium you ...

  10. Effects of salinity and humic acid on the sorption of Hg on Fe and Mn hydroxides.

    Science.gov (United States)

    Liang, Peng; Li, Yi-Chun; Zhang, Chan; Wu, Sheng-Chun; Cui, Hao-Jie; Yu, Shen; Wong, Ming H

    2013-01-15

    The objective of this study was to investigate the influence of humic acid (HA) and salinity on adsorption of Hg on the amorphous and crystalline of iron and manganese hydroxides. The results show that the adsorption of Hg(2+) on Fe and Mn hydroxides was inhibited in marine system due to the formation of stable, nonsorbing aqueous HgCl(2) complexes in solution. Moreover, Cl(-) inhibited the Hg(2+) adsorption more severely on amorphous than crystalline hydroxides. The addition of HA inhibited Hg(2+) adsorption on Fe and Mn hydroxides in freshwater system might be attributed to the competition between Hg(2+) and HA on adsorption to Fe and Mn hydroxides. In contrast, the addition of HA promoted Hg(2+) adsorption on Fe and Mn hydroxides in the marine system, which might be due to the addition of humic acid resulted in the reaction between Cl(-) and HA, and therefore the reducing of Cl(-) promoted more Hg(2+) on Fe and Mn hydroxides. In addition, the influence of HA on Hg(2+) adsorption on Fe and Mn hydroxides are more visible for crystalline than amorphous hydroxides.

  11. Effective Production of Sorbitol and Mannitol from Sugars Catalyzed by Ni Nanoparticles Supported on Aluminium Hydroxide

    OpenAIRE

    Rodiansono Rodiansono; Shimazu Shogo

    2013-01-01

    Effective production of hexitols (sorbitol and mannitol) was achieved from sugars by means of nickel nanoparticles supported on aluminium hydroxide (NiNPs/AlOH) catalyst. NiNPs/AlOH catalyst was prepared by a simple and benign environmentally procedure using less amount of sodium hydroxide. ICP-AES and XRD analyses confirmed that the NiNPs/AlOH catalysts comprised a large amount of remained aluminium hydroxide (i.e. bayerite and gibbsite). The presence of aluminium hydroxide caused a high dis...

  12. Kinetics of sorption of oil products by hydroxide precipitates

    Energy Technology Data Exchange (ETDEWEB)

    Petrova, N.A.; Dubrovskaya, G.E.; Berezyuk, V.G.; Pushkarev, V.V.

    1976-01-01

    Study of the kinetics of sorption of oils (palm and coriander oils, Genrex-26, Emulsol E-2(B)) under static conditions by aluminum and iron hydroxide precipitates (with FeSO/sub 4/, FeCl/sub 3/, and AlCl/sub 3/ as coagulants) showed that an increase of temperature to 40 to 50/sup 0/C raises the sorption rate substantially. The kinetic relations can be represented by equations for first-order reactions. The calculated rate constants and the values of the empirical activation energies are evidence of physical sorption with diffusion as the controlling step.

  13. Kinetics of gibbsite leaching in sodium hydroxide aqueous solution

    Directory of Open Access Journals (Sweden)

    Pavlović Ljubica J.

    2002-01-01

    Full Text Available In order to study the kinetics and mechanism of the reaction, laboratory leaching was carried out with industrially produced gibbsite γ-Al(OH3 in aqueous solutions containing an excess of sodium hydroxide. The results obtained reaction temperature, duration and base concentration varied. The basic kinetic parameters were determined from: the reaction rate constant k=8.72·107 exp (-74990/RT and the process activation energy in the range Ea=72.5-96.81 kJ/mol.

  14. The photoluminescence of Co-Al-layered double hydroxide

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    We report a new optical behaviour of pure Co-Al-layered double hydroxide (LDH). It was found that the Co-Al-LDH sample could emit fluorescence without any fluorescent substances intercalated. Its excitation spectrum shows a maximum peak near the wavelength 370 nm, the maximum emission peak appears at 430 nm and the photoluminescence colour of the Co-Al-LDH sample is blue. This new optical property will be expected to extend the potential applications of LDHs in optical materials field.

  15. LAYERED DOUBLE HYDROXIDES: NANOMATERIALS FOR APPLICATIONS IN AGRICULTURE

    Directory of Open Access Journals (Sweden)

    Luíz Paulo Figueredo Benício

    2015-02-01

    Full Text Available The current research aims to introduce Layered Double Hydroxides (LDH as nanomaterials to be used in agriculture, with particular reference to its use as storage and slow release matrix of nutrients and agrochemicals for plant growing. Structural characteristics, main properties, synthesis methods and characterization of LDH were covered in this study. Moreover, some literature data have been reported to demonstrate their potential for storage and slow release of nitrate, phosphate, agrochemicals, besides as being used as adsorbent for the wastewater treatment. This research aims to expand, in near future, the investigation field on these materials, with application in agriculture, increasing the interface between chemistry and agronomy.

  16. Reactive Crystallization of Calcium Sulfate Dihydrate from Acidic Wastewater and Lime

    Institute of Scientific and Technical Information of China (English)

    邓立聪; 张亦飞; 陈芳芳; 曹绍涛; 游韶玮; 刘艳; 张懿

    2013-01-01

    The present work focused on the recycle of the sulfate and the metal ions from acidic wastewater dis-charged by nonferrous metallurgical industry. The effects of the temperature, the reactant concentration, the stirring speed and the metal ions on the reactive crystallization process of calcium sulfate between sulfuric acid and lime were systematically investigated. The morphology of the precipitated crystals evolved from platelet-like and nee-dle-like shape to rod-like shape when the temperature was increased from 25 to 70 °C. An increase in the agglom-eration of calcium sulfate was found with increasing lime concentration. Metal ions markedly retard the rate of crystallization of calcium sulfate dihydrate. The crystallization of gypsum was slowed with the existence of Mg2+in the solution, and the morphology of gypsum was transformed from platelet-like shape to rod-like shape when Mg2+concentration reached 0.08 mol·L-1. The amorphous ferric hydroxide was coated on the calcium sulfate after the co-precipitation process while Zn2+and Al3+ions in the solution enhanced the agglomeration of the calcium sulfate by absorbing on the surface of the crystals. Comprehensive acidic wastewater containing heavy metals was effi-ciently purified by the two stage lime neutralization technology, and highly agglomerated gypsum precipitates with needle-like shape were obtained. The precipitates could be purified by sulfuric acid washing, and the metal ions were effectively separated from the calcium sulfate by-products.

  17. Investigation into the role of NaOH and calcium ions in the synthesis of calcium phosphate nanoshells

    Directory of Open Access Journals (Sweden)

    C. H. Yeo

    2012-03-01

    Full Text Available Calcium phosphate (CaP nanoshells were prepared using negatively charged liposomes (1,2-dioleoyl-sn-glycero-3-phosphate sodium salt (DOPA as a template by base titration synthesis at various concentrations of NaOH and calcium ions. The elemental composition, morphology, particle size, particle size distribution and zeta potential of the products were determined via various characterisation techniques, such as energy-dispersive X-ray spectrometry (EDX, transmission electron microscopy (TEM, dynamic light scattering (DLS, laser Doppler velocimetry (LDV and Fourier transform infrared spectroscopy (FTIR. The best results showed that stable spherical CaP nanoshells with a mean particle size of 197.5 ± 5.8 nm and a zeta potential of -34.5 ± 0.6 mV were successfully formed when 0.100 M sodium hydroxide (NaOH and 0.100 M calcium ions were used. Moreover, an optimal pH of 10.52 and a final Ca/P molar ratio of 0.97 were achieved under these conditions.

  18. Calcium, vitamin D and bone

    OpenAIRE

    Borg, Andrew A.

    2012-01-01

    Calcium, protein and vitamin D are the main nutrients relevant to bone health. This short article discusses the importance of vitamin D and its relation to calcium homeostasis. The various causes, clinical manifestations and treatment are outlined.

  19. Calcium ion channel and epilepsy

    Institute of Scientific and Technical Information of China (English)

    Yudan Lü; Weihong Lin; Dihui Ma

    2006-01-01

    OBJECTIVE: To review the relationship between calcium ion channel and epilepsy for well investigating the pathogenesis of epilepsy and probing into the new therapeutic pathway of epilepsy.DATA SOURCES: A computer-based online research Calcium ion channel and epilepsy related articles published between January 1994 and December 2006 in the CKNI and Wanfang database with the key words of "calcium influxion, epilepsy, calcium-channel blocker". The language was limited to Chinese. At the same time,related articles published between January 1993 and December 2006 in Pubmed were searched for on online with the key words of "calcium influxion, epilepsy" in English.STUDY SELECTION: The materials were selected firstly. Inclusive criteria: ① Studies related to calcium ion channel and the pat1hogenesis of epilepsy. ② Studies on the application of calcium ion channel blocker in the treatment of epilepsy. Exclusive criteria: repetitive or irrelated studies.DATA EXTRACTION: According to the criteria, 123 articles were retrieved and 93 were excluded due to repetitive or irrelated studies. Altogether 30 articles met the inclusive criteria, 11 of them were about the structure and characters of calcium ion channel, 10 about calcium ion channel and the pathogenesis of epilepsy and 9 about calcium blocker and the treatment of epilepsy.DATA SYNTHESIS: Calcium ion channels mainly consist of voltage dependent calcium channel and receptor operated calcium channel. Depolarization caused by voltage gating channel-induced influxion is the pathological basis of epileptic attack, and it is found in many studies that many anti-epileptic drugs have potential and direct effect to rivalizing voltage-dependent calcium ion channel.CONCLUSION: Calcium influxion plays an important role in the seizure of epilepsy. Some calcium antagonists seen commonly are being tried in the clinical therapy of epilepsy that is being explored, not applied in clinical practice. If there are enough evidences to

  20. Calcium carbonate overdose

    Science.gov (United States)

    Calcium carbonate is not very poisonous. Recovery is quite likely. But, long-term overuse is more serious than a single overdose, because it can cause kidney damage. Few people die from an antacid overdose. Keep all medicines in child-proof bottles and out ...

  1. High Blood Calcium (Hypercalcemia)

    Science.gov (United States)

    ... as well as kidney function and levels of calcium in your urine. Your provider may do other tests to further assess your condition, such as checking your blood levels of phosphorus (a mineral). Imaging studies also may be helpful, such as bone ...

  2. Solar Imagery - Chromosphere - Calcium

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset consists of full-disk images of the sun in Calcium (Ca) II K wavelength (393.4 nm). Ca II K imagery reveal magnetic structures of the sun from about 500...

  3. Ions in water: the microscopic structure of concentrated hydroxide solutions.

    Science.gov (United States)

    Imberti, S; Botti, A; Bruni, F; Cappa, G; Ricci, M A; Soper, A K

    2005-05-15

    Neutron-diffraction data on aqueous solutions of hydroxides, at solute concentrations ranging from 1 solute per 12 water molecules to 1 solute per 3 water molecules, are analyzed by means of a Monte Carlo simulation (empirical potential structure refinement), in order to determine the hydration shell of the OH- in the presence of the smaller alkali metal ions. It is demonstrated that the symmetry argument between H+ and OH- cannot be used, at least in the liquid phase at such high concentrations, for determining the hydroxide hydration shell. Water molecules in the hydration shell of K+ orient their dipole moment at about 45 degrees from the K+-water oxygen director, instead of radially as in the case of the Li+ and Na+ hydration shells. The K+-water oxygen radial distribution function shows a shallower first minimum compared to the other cation-water oxygen functions. The influence of the solutes on the water-water radial distribution functions is shown to have an effect on the water structure equivalent to an increase in the pressure of the water, depending on both ion concentration and ionic radius. The changes of the water structure in the presence of charged solutes and the differences among the hydration shells of the different cations are used to present a qualitative explanation of the observed cation mobility.

  4. Selectivity of Crystal Growth Direction in Layered Double Hydroxides

    Institute of Scientific and Technical Information of China (English)

    赵芸; 梁吉; 李峰; 段雪

    2004-01-01

    Investigation of selectivity of crystal growth direction in layered double hydroxides is helpful to control their particle sizes in different directions. Mg-Al layered double hydroxides (LDHs) were synthesized using a coprecipitation method. The influences of aging temperature, aging time, and Mg/Al molar ratio on the crystal structure, the LDHs particle size, and the selectivity of crystal growth in different directions were investigated. The results show that the size of the crystallites in the a direction is larger than that in the c direction for all experimental conditions, indicating faster crystal growth in the a direction than in the c direction. The crystallite sizes in the a and c directions both increase with decreasing Mg/Al molar ratio but with less difference between the sizes in the two directions. Therefore, the crystal growth rate in the c direction increases more than that in the a direction as the Mg/Al molar ratio decreases. The influence of the aging time, aging temperature, and Mg/Al molar ratio on the selectivity of the crystal growth direction can be used to prepare LDHs with selected sizes in the a and c directions.

  5. Experimental and Theoretical Studies of Volatile Metal Hydroxides

    Science.gov (United States)

    Myers, Dwight L.; Jacobson, Nathan S.

    2015-01-01

    Modern superalloys used in the construction of turbomachinery contain a wide range of metals in trace quantities. In addition, metal oxides and silicon dioxide are used to form Thermal Barrier Coatings (TBC) to protect the underlying metal in turbine blades. Formation of volatile hydroxides at elevated temperatures is an important mechanism for corrosion of metal alloys or oxides in combustion environments (N. Jacobson, D. Myers, E. Opila, and E. Copland, J. Phys. Chem. Solids 66, 471-478, 2005). Thermodynamic data is essential to proper design of components of modern gas turbines. It is necessary to first establish the identity of volatile hydroxides formed from the reaction of a given system with high temperature water vapor, and then to determine the equilibrium pressures of the species under operating conditions. Theoretical calculations of reaction energies are an important check of experimental results. This presentation reports results for several important systems: Si-O-H, Cr-O-H, Al-O-H, Ti-O-H, and ongoing studies of Ta-O-H.

  6. Cation ordering and superstructures in natural layered double hydroxides.

    Science.gov (United States)

    Krivovichev, Sergey V; Yakovenchuk, Victor N; Zolotarev, Andrey A; Ivanyuk, Gregory N; Pakhomovsky, Yakov A

    2010-01-01

    Layered double hydroxides (LDHs) constitute an important group of materials with many applications ranging from catalysis and absorption to carriers for drug delivery, DNA intercalation and carbon dioxide sequestration. The structures of LDHs are based upon double brucite-like hydroxide layers [M(2+)(n)M(3+)(m)(OH)(2(m+n)](m+), where M(2+) = Mg(2+), Fe(2+), Mn(2+), Zn(2+), etc.; M(3+) = Al(3+), Fe(3+), Cr(3+), Mn(3+), etc. Structural features of LDHs such as cation ordering, charge distribution and polytypism have an immediate influence upon their properties. However, all the structural studies on synthetic LDHs deal with powder samples that prevent elucidation of such fine details of structure architecture as formation of superstructures due to cation ordering. In contrast to synthetic materials, natural LDHs are known to form single crystals accessible to single-crystal X-ray diffraction analysis, which provides a unique possibility to investigate 3D cation ordering in LDHs that results in formation of complex superstructures, where 2D cation order is combined with a specific order of layer stacking (polytypism). Therefore LDH minerals provide an indispensable source of structural information for modeling of structures and processes happening in LDHs at the molecular and nanoscale levels.

  7. Calcium aluminate in alumina

    Science.gov (United States)

    Altay, Arzu

    The properties of ceramic materials are determined not only by the composition and structure of the phases present, but also by the distribution of impurities, intergranular films and second phases. The phase distribution and microstructure both depend on the fabrication techniques, the raw materials used, the phase-equilibrium relations, grain growth and sintering processes. In this dissertation research, various approaches have been employed to understand fundamental phenomena such as grain growth, impurity segregation, second-phase formation and crystallization. The materials system chosen was alumina intentionally doped with calcium. Atomic-scale structural analyses of grain boundaries in alumina were carried on the processed samples. It was found that above certain calcium concentrations, CA6 precipitated as a second phase at all sintering temperatures. The results also showed that abnormal grain growth can occur after precipitation and it is not only related to the calcium level, but it is also temperature dependent. In order to understand the formation mechanism of CA6 precipitates in calcium doped alumina samples, several studies have been carried out using either bulk materials or thin films The crystallization of CA2 and CA6 powders has been studied. Chemical processing techniques were used to synthesize the powders. It was observed that CA2 powders crystallized directly, however CA6 powders crystallized through gamma-Al 2O3 solid solution. The results of energy-loss near-edge spectrometry confirmed that gamma-Al2O3 can dissolve calcium. Calcium aluminate/alumina reaction couples have also been investigated. All reaction couples were heat treated following deposition. It was found that gamma-Al2O3 was formed at the interface as a result of the interfacial reaction between the film and the substrate. gamma-Al 2O3 at the interface was stable at much higher temperatures compared to the bulk gamma-Al2O3 formed prior to the CA6 crystallization. In order to

  8. Calcium addition in straw gasification

    DEFF Research Database (Denmark)

    Risnes, H.; Fjellerup, Jan Søren; Henriksen, Ulrik Birk

    2003-01-01

    The present work focuses on the influence of calcium addition in gasification. The inorganic¿organic element interaction as well as the detailed inorganic¿inorganic elements interaction has been studied. The effect of calcium addition as calcium sugar/molasses solutions to straw significantly...

  9. Durability Study on High Calcium Fly Ash Based Geopolymer Concrete

    Directory of Open Access Journals (Sweden)

    Ganesan Lavanya

    2015-01-01

    Full Text Available This study presents an investigation into the durability of geopolymer concrete prepared using high calcium fly ash along with alkaline activators when exposed to 2% solution of sulfuric acid and 5% magnesium sulphate for up to 45 days. The durability was also assessed by measuring water absorption and sorptivity. Ordinary Portland cement concrete was also prepared as control concrete. The grades chosen for the investigation were M20, M40, and M60. The alkaline solution used for present study is the combination of sodium silicate and sodium hydroxide solution with the ratio of 2.50. The molarity of sodium hydroxide was fixed as 12. The test specimens were 150×150×150 mm cubes, 100×200 mm cylinders, and 100×50 mm discs cured at ambient temperature. Surface deterioration, density, and strength over a period of 14, 28, and 45 days were observed. The results of geopolymer and ordinary Portland cement concrete were compared and discussed. After 45 days of exposure to the magnesium sulfate solution, the reduction in strength was up to 12% for geopolymer concrete and up to 25% for ordinary Portland cement concrete. After the same period of exposure to the sulphuric acid solution, the compressive strength decrease was up to 20% for geopolymer concrete and up to 28% for ordinary Portland cement concrete.

  10. EXPERIMENTAL EVALUATION OF LOW CALCIUM FLY ASH BASED GEOPOLYMER CONCRETE

    Directory of Open Access Journals (Sweden)

    NIRAGI DAVE

    2012-12-01

    Full Text Available There are many ways to reduce environmental pollution that causes by production of Portland cement and cause by the increasing of waste material. Geopolymer concrete results from the reaction of a source material that is rich in silica and alumina with alkaline liquid. In this experiment low calcium (ASTM Class F fly ash based Geopolymer is used as the binder, in the replacement of portland cement to produce Geopolymer concrete. The alkaline liquid that been used in geopolymerisation is the combination of sodium hydroxide (NaOH and sodium metasilicate (Na2Sio2. Fly ash has been collected from Badarpur NTPC plant, New Delhi. In the present study, three (3 series of geopolymer concrete specimens composing molar of sodium hydroxide (NaOH which is 8M was adopted. There are 9 cube specimens at size 150mm x 150mm x 150mm were prepared. The test specimenswere cured at 60 degree in an oven and at ambient condition. The curing time varied from 24 hour to 168 hours (7 days. The result shows that the strength of geopolymer concrete after 24 hour is not superior and after 7 day the compressive strength of Geopolymer concrete is moderate. Therefore further curing period and temperatureshould be improved.

  11. Styrene epoxidation with hydrogen peroxide over calcium oxide catalysts prepared from various precursors

    Institute of Scientific and Technical Information of China (English)

    Qingming Gu; Dan Han; Lei Shi; Qi Sun

    2012-01-01

    A series of CaO samples were prepared by calcination of commercially available and synthesis of calcium salt precursors such as calcium acetate,carbonate,hydroxide and oxalate etc.CaO samples were found to be effective for the epoxidation of styrene using hydrogen peroxide as an oxidant in the presence of acetonitrile.To determine the influence of the physicochemical properties and surface basicity on the catalytic activity,the prepared CaO samples were characterized using thermogravimetry (TG),X-ray diffraction (XRD),scanning electron microscopy (SEM),N2-adsorption and temperature-programmed desorption of CO2 (CO2-TPD).The results indicate that the amounts of very strong basic sites and high basicity strength on CaO sample are key factors for its excellent catalytic performance.In contrast,the surface area,porosity and the surface structure of CaO sample have a relatively minor effect on the catalytic activity.CaO sample,obtained by the decomposition of Ca(OH)2,prepared by precipitating calcium nitrate with sodium hydroxide in ethylene glycol solution,exhibits the highest amount of very strong basic sites and stronger strength of basic sites,and therefore it catalyses the epoxidation of styrene with the highest rate among the tested CaO samples.Under the selected reaction conditions,the selectivity of 97.5% to styrene oxide at a conversion in excess of 99% could be obtained.

  12. Evaluation of the Chemical and Mechanical Properties of Hardening High-Calcium Fly Ash Blended Concrete

    Directory of Open Access Journals (Sweden)

    Wei-Jie Fan

    2015-09-01

    Full Text Available High-calcium fly ash (FH is the combustion residue from electric power plants burning lignite or sub-bituminous coal. As a mineral admixture, FH can be used to produce high-strength concrete and high-performance concrete. The development of chemical and mechanical properties is a crucial factor for appropriately using FH in the concrete industry. To achieve sustainable development in the concrete industry, this paper presents a theoretical model to systematically evaluate the property developments of FH blended concrete. The proposed model analyzes the cement hydration, the reaction of free CaO in FH, and the reaction of phases in FH other than free CaO. The mutual interactions among cement hydration, the reaction of free CaO in FH, and the reaction of other phases in FH are also considered through the calcium hydroxide contents and the capillary water contents. Using the hydration degree of cement, the reaction degree of free CaO in FH, and the reaction degree of other phases in FH, the proposed model evaluates the calcium hydroxide contents, the reaction degree of FH, chemically bound water, porosity, and the compressive strength of hardening concrete with different water to binder ratios and FH replacement ratios. The evaluated results are compared to experimental results, and good consistencies are found.

  13. Bioceramics of calcium orthophosphates.

    Science.gov (United States)

    Dorozhkin, Sergey V

    2010-03-01

    A strong interest in use of ceramics for biomedical applications appeared in the late 1960's. Used initially as alternatives to metals in order to increase a biocompatibility of implants, bioceramics have become a diverse class of biomaterials, presently including three basic types: relatively bioinert ceramics, bioactive (or surface reactive) and bioresorbable ones. Furthermore, any type of bioceramics could be porous to provide tissue ingrowth. This review is devoted to bioceramics prepared from calcium orthophosphates, which belong to the categories of bioresorbable and bioactive compounds. During the past 30-40 years, there have been a number of major advances in this field. Namely, after the initial work on development of bioceramics that was tolerated in the physiological environment, emphasis was shifted towards the use of bioceramics that interacted with bones by forming a direct chemical bond. By the structural and compositional control, it became possible to choose whether the bioceramics of calcium orthophosphates was biologically stable once incorporated within the skeletal structure or whether it was resorbed over time. At the turn of the millennium, a new concept of calcium orthophosphate bioceramics, which is able to regenerate bone tissues, has been developed. Current biomedical applications of calcium orthophosphate bioceramics include replacements for hips, knees, teeth, tendons and ligaments, as well as repair for periodontal disease, maxillofacial reconstruction, augmentation and stabilization of the jawbone, spinal fusion and bone fillers after tumor surgery. Potential future applications of calcium orthophosphate bioceramics will include drug-delivery systems, as well as they will become effective carriers of growth factors, bioactive peptides and/or various types of cells for tissue engineering purposes.

  14. Ion-pair formation in aqueous strontium chloride and strontium hydroxide solutions under hydrothermal conditions by AC conductivity measurements.

    Science.gov (United States)

    Arcis, H; Zimmerman, G H; Tremaine, P R

    2014-09-01

    Frequency-dependent electrical conductivities of solutions of aqueous strontium hydroxide and strontium chloride have been measured from T = 295 K to T = 625 K at p = 20 MPa, over a very wide range of ionic strength (3 × 10(-5) to 0.2 mol kg(-1)), using a high-precision flow AC conductivity instrument. Experimental values for the concentration-dependent equivalent conductivity, Λ, of the two electrolytes were fitted with the Turq-Blum-Bernard-Kunz ("TBBK") ionic conductivity model, to determine ionic association constants, K(A,m). The TBBK fits yielded statistically significant formation constants for the species SrOH(+) and SrCl(+) at all temperatures, and for Sr(OH)2(0) and SrCl2(0) at temperatures above 446 K. The first and second stepwise association constants for the ion pairs followed the order K(A1)(SrOH(+)) > K(A1)(SrCl(+)) > K(A2)[Sr(OH)2(0)] > K(A2)[SrCl2(0)], consistent with long-range solvent polarization effects associated with the lower static dielectric constant and high compressibility of water at elevated temperatures. The stepwise association constants to form SrCl(+) agree with previously reported values for CaCl(+) to within the combined experimental error at high temperatures and, at temperatures below ∼375 K, the values of log10 KA1 for strontium are lower than those for calcium by up to ∼0.3-0.4 units. The association constants for the species SrOH(+) and Sr(OH)2(0) are the first accurate values to be reported for hydroxide ion pairs with any divalent cation under these conditions.

  15. Synthesis and characterization of laurate-intercalated Mg–Al layered double hydroxide prepared by coprecipitation

    DEFF Research Database (Denmark)

    Gerds, Nathalie Christiane; Katiyar, Vimal; Koch, Christian Bender

    2012-01-01

    Effective utilization of layered double hydroxides (LDH) for industrial applications requires the synthesis of pure and well-defined LDH phases. In the present study, dodecanoate (laurate) anions were intercalated into Mg–Al-layered double hydroxide (LDH-C12) by coprecipitation in the presence of...

  16. Mg/Al Ordering in Layered Double Hydroxides Revealed by Multinuclear NMR Spectroscopy

    DEFF Research Database (Denmark)

    Nielsen, Ulla Gro; Grey, Clare P.; Sideris, Paul J.

    2008-01-01

    The anion- exchange ability of layered double hydroxides ( LDHs) has been exploited to create materials for use in catalysis, drug delivery, and environmental remediation. The specific cation arrangements in the hydroxide layers of hydrotalcite- like LDHs, of general formula Mg1-x2+Alx3+OH2(Anion...

  17. Layered double hydroxide stability. 2. Formation of Cr(III)-containing layered double hydroxides directly from solution

    Science.gov (United States)

    Boclair, J. W.; Braterman, P. S.; Jiang, J.; Lou, S.; Yarberry, F.

    1999-01-01

    Solutions containing divalent metal [M(II) = Mg2+, Zn2+, Co2+, Ni2+, Mn2+] chlorides and CrCl3 6H2O were titrated with NaOH to yield, for M(II) = Zn, Co, and Ni, hydrotalcite-like layered double hydroxides (LDHs), [[M(II)]1-z[Cr(III)]z(OH)2][Cl]z yH2O, in a single step, without intermediate formation of chromium hydroxide. Analysis of the resultant titration curves yields solubility constants for these compounds. These are in the order Zn < Ni approximately Co, with a clear preference for formation of the phase with z = 1/3. With Mg2+ as chloride, titration gives a mixture of Cr(OH)3 and Mg(OH)2, but the metal sulfates give Mg2Cr(OH)6 1/2(SO4) by a two-step process. Titrimetric and spectroscopic evidence suggests short-range cation order in the one-step LDH systems.

  18. Calcium signaling in taste cells.

    Science.gov (United States)

    Medler, Kathryn F

    2015-09-01

    The sense of taste is a common ability shared by all organisms and is used to detect nutrients as well as potentially harmful compounds. Thus taste is critical to survival. Despite its importance, surprisingly little is known about the mechanisms generating and regulating responses to taste stimuli. All taste responses depend on calcium signals to generate appropriate responses which are relayed to the brain. Some taste cells have conventional synapses and rely on calcium influx through voltage-gated calcium channels. Other taste cells lack these synapses and depend on calcium release to formulate an output signal through a hemichannel. Beyond establishing these characteristics, few studies have focused on understanding how these calcium signals are formed. We identified multiple calcium clearance mechanisms that regulate calcium levels in taste cells as well as a calcium influx that contributes to maintaining appropriate calcium homeostasis in these cells. Multiple factors regulate the evoked taste signals with varying roles in different cell populations. Clearly, calcium signaling is a dynamic process in taste cells and is more complex than has previously been appreciated. This article is part of a Special Issue entitled: 13th European Symposium on Calcium.

  19. The Deactivation of Nickel Hydroxide to Hypophosphite Electrooxidation on a Nickel Electrode

    Institute of Scientific and Technical Information of China (English)

    Yue ZENG; Min MO; Jian Long YI; Xin Jun TANG; Hui Xian WANG

    2004-01-01

    The deactivation of nickel hydroxide to the electrooxidation of hypophosphite on a nickel electrode was studied by means of in situ UV-Vis subtractive reflectance spectroscopy. The experimental results show that when the potential is lower than -1.0 V (SCE), the surface on nickel electrode is free of nickel hydroxide, on which hypophosphite is active. When the potential moves positively to about-0.75V, two absorbency bands around 300 nm and 550 nm, which were ascribed to the formation of α-nickel hydroxide, were observed, nickel is oxidized to α-nickel hydroxide.Severe deactivation of the surface occurs when the nickel surface is covered with nickel hydroxide,which separates the hypophosphite ion from nickel substrate.

  20. Synthesis and structure refinement of layered double hydroxides of Co, Mg and Ni with Ga

    Indian Academy of Sciences (India)

    G V Manohara; P Vishnu Kamath

    2010-06-01

    Homogeneous precipitation by urea hydrolysis results in the formation of highly ordered layered double hydroxides of divalent metal ions (Co, Mg, Ni) and Ga. Structure refinement shows that these carbonate containing layered hydroxides crystallize with rhombohedral symmetry (space group -3) in the structure of the 31 polytype. An analysis of the structure shows that, coulombic attraction between the layer and interlayer remains invariant in different layered hydroxides, whereas the strength of hydrogen bonding varies. The Ni–Ga LDH has the weakest hydrogen bonding and Co–Ga, the strongest, as reflected by the layer–interlayer oxygen–oxygen distances. The poor polarity of the OH bond in the Ni–Ga hydroxide points to the greater covalency of the (2+}/′3+)-oxygen bond in this compound as opposed to the Co–Ga hydroxide. These observations are supported by IR spectra.

  1. Fruit Calcium: Transport and Physiology

    Directory of Open Access Journals (Sweden)

    Bradleigh eHocking

    2016-04-01

    Full Text Available Calcium has well-documented roles in plant signaling, water relations and cell wall interactions. Significant research into how calcium impacts these individual processes in various tissues has been carried out; however, the influence of calcium on fruit ripening has not been thoroughly explored. Here, we review the current state of knowledge on how calcium may impact fruit development, physical traits and disease susceptibility through facilitating developmental and stress response signaling, stabilizing membranes, influencing water relations and modifying cell wall properties through cross-linking of de-esterified pectins. We explore the involvement of calcium in hormone signaling integral to ripening and the physiological mechanisms behind common disorders that have been associated with fruit calcium deficiency (e.g. blossom end rot in tomatoes or bitter pit in apples. This review works towards an improved understanding of how the many roles of calcium interact to influence fruit ripening, and proposes future research directions to fill knowledge gaps. Specifically, we focus mostly on grapes and present a model that integrates existing knowledge around these various functions of calcium in fruit, which provides a basis for understanding the physiological impacts of sub-optimal calcium nutrition in grapes. Calcium accumulation and distribution in fruit is shown to be highly dependent on water delivery and cell wall interactions in the apoplasm. Localized calcium deficiencies observed in particular species or varieties can result from differences in xylem morphology, fruit water relations and pectin composition, and can cause leaky membranes, irregular cell wall softening, impaired hormonal signaling and aberrant fruit development. We propose that the role of apoplasmic calcium-pectin crosslinking, particularly in the xylem, is an understudied area that may have a key influence on fruit water relations. Furthermore, we believe that improved

  2. DISTILLATION OF CALCIUM

    Science.gov (United States)

    Barton, J.

    1954-07-27

    This invention relates to an improvement in the process for the purification of caicium or magnesium containing an alkali metal as impurity, which comprises distiiling a batch of the mixture in two stages, the first stage distillation being carried out in the presence of an inert gas at an absolute pressure substantially greater than the vapor pressure of calcium or maguesium at the temperature of distillation, but less than the vaper pressure at that temperature of the alkali metal impurity so that only the alkali metal is vaporized and condensed on a condensing surface. A second stage distilso that substantially only the calcium or magnesium distills under its own vapor pressure only and condenses in solid form on a lower condensing surface.

  3. Synthesis of calcium superoxide

    Science.gov (United States)

    Rewick, R. T.; Blucher, W. G.; Estacio, P. L.

    1972-01-01

    Efforts to prepare Ca(O2) sub 2 from reactions of calcium compounds with 100% O3 and with O(D-1) atoms generated by photolysis of O3 at 2537 A are described. Samples of Ca(OH) sub 2, CaO, CaO2, Ca metal, and mixtures containing suspected impurities to promote reaction have been treated with excess O3 under static and flow conditions in the presence and absence of UV irradiation. Studies with KO2 suggest that the superoxide anion is stable to radiation at 2537 A but reacts with oxygen atoms generated by the photolysis of O3 to form KO3. Calcium superoxide is expected to behave in an analogous.

  4. Exploration of As(III)/As(V) Uptake from Aqueous Solution by Synthesized Calcium Sulfate Whisker☆

    Institute of Scientific and Technical Information of China (English)

    Xiaojuan Chen; Liuchun Yang; Junfeng Zhang; Yan Huang

    2014-01-01

    Although common calcium-containing minerals such as calcite and gypsum may fix arsenic, the interaction be-tween modified calcic minerals and arsenic has seldom been reported. The uptake behavior of As(III)/As(V) from aqueous solutions by calcium sulfate whisker (CSW, dihydrate or anhydrite) synthesized through a cooling recrystal ization method was explored. A series of batch experiments were conducted to examine the effect of pH, reaction time, whisker dosage, and initial As concentration. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to characterize the samples prepared. The results showed that pH of the aqueous solution was an important parameter for As(III)/As(V) uptake, and an excellent removal efficiency could be achieved under strongly alkaline condition. The data from batch experiments for reaction of As(V) with calcium sulfate dihydrate whisker (CSDW) and calcium sulfate anhydrous whisker (CSAW) were well described with extended Langmuir EXT1 model, from which theoretic maximum adsorption capacity of 46.57 mg As(V)·(g CSDW)−1 and 39.18 mg As(V)·(g CSAW)−1 were obtained. Some calcium arsenate solids products, such as CaAsO3(OH) (weilite, syn), Ca3(AsO4)2 (calcium arsenate), CaO–As2O5, Ca–As–O, Ca5(AsO4)3OH·xH2O (calcium arsenate hydroxide hydrate), and CaH(AsO4)·2H2O (hydrogen calcium arsenic oxide hydrate), were detected at pH = 12.5 through XRD analysis. This indicates that the interaction mechanism between As(V) and CSW is a complex adsorption process combined with surface dissolution and chemical precipitation.

  5. Calcium oxide as a solid base catalyst for transesterification of soybean oil and its application to biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    Masato Kouzu; Takekazu Kasuno; Masahiko Tajika; Yoshikazu Sugimoto; Shinya Yamanaka; Jusuke Hidaka [Keihanna Interaction Plaza Inc., Kyoto (Japan). JST-KFPT Core Research Center

    2008-09-15

    In order to study solid base catalyst for biodiesel production with environmental benignity, transesterification of edible soybean oil with refluxing methanol was carried out in the presence of calcium oxide (CaO), -hydroxide (Ca(OH){sub 2}), or -carbonate (CaCO{sub 3}). At 1 h of reaction time, yield of FAME was 93% for CaO, 12% for Ca(OH){sub 2}, and 0% for CaCO{sub 3}. Under the same reacting condition, sodium hydroxide with the homogeneous catalysis brought about the complete conversion into FAME. Also, CaO was used for the further tests transesterifying waste cooking oil (WCO) with acid value of 5.1 mg-KOH/g. The yield of FAME was above 99% at 2 h of reaction time, but a portion of catalyst changed into calcium soap by reacting with free fatty acids included in WCO at initial stage of the transesterification. Owing to the neutralizing reaction of the catalyst, concentration of calcium in FAME increased from 187 ppm to 3065 ppm. By processing WCO at reflux of methanol in the presence of cation-exchange resin, only the free fatty acids could be converted into FAME. The transesterification of the processed WCO with acid value of 0.3 mg-KOH/g resulted in the production of FAME including calcium of 565 ppm. 22 refs., 6 figs., 5 tabs.

  6. Layered Double Hydroxide-Based Nanocarriers for Drug Delivery

    Directory of Open Access Journals (Sweden)

    Xue Bi

    2014-06-01

    Full Text Available Biocompatible clay materials have attracted particular attention as the efficient drug delivery systems (DDS. In this article, we review developments in the use of layered double hydroxides (LDHs for controlled drug release and delivery. We show how advances in the ability to synthesize intercalated structures have a significant influence on the development of new applications of these materials. We also show how modification and/or functionalization can lead to new biotechnological and biomedical applications. This review highlights the most recent progresses in research on LDH-based controlled drug delivery systems, focusing mainly on: (i DDS with cardiovascular drugs as guests; (ii DDS with anti-inflammatory drugs as guests; and (iii DDS with anti-cancer drugs as guests. Finally, future prospects for LDH-based drug carriers are also discussed.

  7. Synthesis of tetramethyl ammonium hydroxide by cell diaphragm electrolytic method

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Under the conditions of tetramethyl ammonia chloride (TMAC) used as starting material, Ti-based Dimensionally Stable Anode (DSA), stainless steel used as cathode and Nafion 900 cation membrane as cell diaphragm, this paper studies the synthesis of tetramethyl ammonium hydroxide (TMAH) by cell diaphragm electrolytic method, examining not only the effects of current density, concentration of starting material and cell temperature, on the product purity and current efficiency, but also the effects of electrolyte circulation rate on the service life of Ti-based DSA.The experiment puts forward an optimum processing condition, and experimental findings show that preparing TMAH by using this technique can obtain a current efficiency 74.7 % and get product with a purity greater than 99.9%.

  8. Hydrothermal Synthesis of Ni/Al Layered Double Hydroxide Nanorods

    Directory of Open Access Journals (Sweden)

    Yun Zhao

    2011-01-01

    Full Text Available Ni/Al layered double hydroxide (LDH nanorods were successfully synthesized by the hydrothermal reaction. The crystal structure of the products was characterized by X-ray diffraction (XRD. The morphology of the products was observed using transmission electron microscopy (TEM and field emission scanning electron microscopy (SEM. The influences of reaction time and pH value on the morphology of the Ni/Al LDHs were investigated. The result showed that the well-crystallized nanorods of Ni/Al LDHs could be obtained when the pH value was about 10.0 with a long reaction time (12–18 h at 180°C.

  9. Hydroxide as general base in the saponification of ethyl acetate.

    Science.gov (United States)

    Mata-Segreda, Julio F

    2002-03-13

    The second-order rate constant for the saponification of ethyl acetate at 30.0 degrees C in H(2)O/D(2)O mixtures of deuterium atom fraction n (a proton inventory experiment) obeys the relation k(2)(n) = 0.122 s(-1) M(-1) (1 - n + 1.2n) (1 - n + 0.48n)/(1 - n + 1.4n) (1 - n + 0.68n)(3). This result is interpreted as a process where formation of the tetrahedral intermediate is the rate-determining step and the transition-state complex is formed via nucleophilic interaction of a water molecule with general-base assistance from hydroxide ion, opposite to the direct nucleophilic collision commonly accepted. This mechanistic picture agrees with previous heavy-atom kinetic isotope effect data of Marlier on the alkaline hydrolysis of methyl formate.

  10. Biological evaluation of layered double hydroxides as efficient drug vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Li Yan; Liu Dan; Chang Qing; Liu Dandan; Xia Ying; Liu Shuwen; Peng Nanfang; Yang Xu [Hubei Key Laboratory of Genetic Regulation and Integrative Biology, College of Life Science, Huazhong Normal University, Wuhan 430079 (China); Ai Hanhua [College of Physical Science and Technology, Huazhong Normal University, Wuhan 430079 (China); Xi Zhuge, E-mail: yangxu@mail.ccnu.edu.cn [Tianjin Institutes of Health and Environmental Medicine, Tianjin 300050 (China)

    2010-03-12

    Recently there has been a rapid expansion of the development of bioinorganic hybrid systems for safe drug delivery. Layered double hydroxides (LDH), a variety of available inorganic matrix, possess great promise for this purpose. In this study, an oxidative stress biomarker system, including measurement of reactive oxygen species, glutathione content, endogenous nitric oxide, carbonyl content in proteins, DNA strand breaks and DNA-protein crosslinks, was designed to evaluate the biocompatibility of different concentrations of nano-Zn/Al-LDH with a Hela cell line. The drug delivery activity of the LDH-folic-acid complex was also assessed. The resulting data clearly demonstrated that nano-LDH could be applied as a relatively safe drug vehicle with good delivery activity, but with the caveat that the effects of high dosages observed here should not be ignored when attempting to maximize therapeutic activity by increasing LDH concentration.

  11. Electronic spectra of anions intercalated in layered double hydroxides

    Indian Academy of Sciences (India)

    S Radha; P Vishnu Kamath

    2013-10-01

    Transition metal complexes intercalated in layered double hydroxides have a different electronic structure as compared to their free state owing to their confinement within the interlayer gallery. UV–Vis absorptions of the intercalated complex anions show a significant shift as compared to their free state. The ligand to metal charge transfer transitions of the ferricyanide anion show a red shift on intercalation. The ferrocyanide ion shows a significant blue shift of – bands due to the increased separation between 2g and g levels on intercalation. MnO$^{-}_{4}$ ion shows a blue shift in its ligand to metal charge transfer transition since the non-bonding 1 level of oxygen from which the transition arises is stabilized.

  12. Polymerization reaction in restricted space of layered double hydroxides (LDHs)

    Institute of Scientific and Technical Information of China (English)

    SI Lichun; WANG Ge; CAI Fuli; WANG Zhiqiang; DUAN Xue

    2004-01-01

    This paper reported the preparation of styrene sulfonate intercalated layered double hydroxides (LDHs) material, SS-LDHs by coprecipitation method, followed by in-situ polymerization of the monomers in the interlayer space of LDHs. The polymerization reaction was monitored by UV and NMR. It is confirmed that when the reaction occurred at 100℃ for 24 h, part of monomers did not react .When the reaction was carried out at 150℃, the polymeriza tion of the intercalated monomers is complete to afford the polymer intercalated product PSS-LDHs. During the polymerization process, the layered structure remains well. At thesame time the gallery height increases with the lengthening of reaction time. This is preliminarily because that the PSS becomes more swelling with the amount of water it absorbs due to its hygroscopicity property.

  13. The kinetic parameters of carbonaceous materials activated with potassium hydroxide

    Energy Technology Data Exchange (ETDEWEB)

    Yong, Z.; Han, B.X.

    2000-07-01

    On the basis of microspore formation in carbonaceous materials, the activation energy for the potassium hydroxide activation of Chinese petroleum coke and coal has been deduced theoretically as dB(O)/dt = A exp(-E(a)) is an element of/RT), where is an element of is the formation energy for the metastable solid formed at the activation temperature. The kinetic parameters (frequency factor, A, and apparent activation energy, E(a) were calculated from this equation as being 5.319 mg/(g min), 36.51 kJ/mol and 6.64 mg/(g min), 49.46 kJ/mol, respectively, for the two carbonaceous materials studied.

  14. Models of calcium signalling

    CERN Document Server

    Dupont, Geneviève; Kirk, Vivien; Sneyd, James

    2016-01-01

    This book discusses the ways in which mathematical, computational, and modelling methods can be used to help understand the dynamics of intracellular calcium. The concentration of free intracellular calcium is vital for controlling a wide range of cellular processes, and is thus of great physiological importance. However, because of the complex ways in which the calcium concentration varies, it is also of great mathematical interest.This book presents the general modelling theory as well as a large number of specific case examples, to show how mathematical modelling can interact with experimental approaches, in an interdisciplinary and multifaceted approach to the study of an important physiological control mechanism. Geneviève Dupont is FNRS Research Director at the Unit of Theoretical Chronobiology of the Université Libre de Bruxelles;Martin Falcke is head of the Mathematical Cell Physiology group at the Max Delbrück Center for Molecular Medicine, Berlin;Vivien Kirk is an Associate Professor in the Depar...

  15. Structural characterisation of a layered double hydroxide nanosheet

    Science.gov (United States)

    Funnell, Nicholas P.; Wang, Qiang; Connor, Leigh; Tucker, Matthew G.; O'Hare, Dermot; Goodwin, Andrew L.

    2014-06-01

    We report the atomic-scale structure of a Zn2Al-borate layered double hydroxide (LDH) nanosheet, as determined by reverse Monte Carlo (RMC) modelling of X-ray total scattering data. This study involves the extension of the RMC method to enable structural refinement of two-dimensional nanomaterials. The refined LDH models show the intra-layer geometry in this highly-exfoliated phase to be consistent with that observed in crystalline analogues, with the reciprocal-space scattering data suggesting a disordered arrangement of the Zn2+ and Al3+ cations within the nanosheet. The approach we develop is generalisable and so offers a method of characterising the structures of arbitrary nanosheet phases, including systems that support complex forms of disorder within the nanosheets themselves.We report the atomic-scale structure of a Zn2Al-borate layered double hydroxide (LDH) nanosheet, as determined by reverse Monte Carlo (RMC) modelling of X-ray total scattering data. This study involves the extension of the RMC method to enable structural refinement of two-dimensional nanomaterials. The refined LDH models show the intra-layer geometry in this highly-exfoliated phase to be consistent with that observed in crystalline analogues, with the reciprocal-space scattering data suggesting a disordered arrangement of the Zn2+ and Al3+ cations within the nanosheet. The approach we develop is generalisable and so offers a method of characterising the structures of arbitrary nanosheet phases, including systems that support complex forms of disorder within the nanosheets themselves. Electronic supplementary information (ESI) available. See DOI: 10.1039/c4nr01265h

  16. An Aluminum Magnesium Hydroxide Stearate-based Skin Barrier Protection Cream Used for the Management of Eczematous Dermatitis

    Science.gov (United States)

    Bhambri, Sanjay; Michaels, Brent

    2008-01-01

    Eczematous dermatoses can often be very difficult to treat. An aluminum magnesium hydroxide stearate-based cream has recently become available for clinical use. Aluminum magnesium hydroxide stearate-based cream provides an alternative option in treating these dermatoses while providing barrier protection against external allergens and irritants. This article reviews various studies evaluating aluminum magnesium hydroxide stearate-based cream. PMID:21212843

  17. Calcium signalling and calcium channels: evolution and general principles.

    Science.gov (United States)

    Verkhratsky, Alexei; Parpura, Vladimir

    2014-09-15

    Calcium as a divalent cation was selected early in evolution as a signaling molecule to be used by both prokaryotes and eukaryotes. Its low cytosolic concentration likely reflects the initial concentration of this ion in the primordial soup/ocean as unicellular organisms were formed. As the concentration of calcium in the ocean subsequently increased, so did the diversity of homeostatic molecules handling calcium. This includes the plasma membrane channels that allowed the calcium entry, as well as extrusion mechanisms, i.e., exchangers and pumps. Further diversification occurred with the evolution of intracellular organelles, in particular the endoplasmic reticulum and mitochondria, which also contain channels, exchanger(s) and pumps to handle the homeostasis of calcium ions. Calcium signalling system, based around coordinated interactions of the above molecular entities, can be activated by the opening of voltage-gated channels, neurotransmitters, second messengers and/or mechanical stimulation, and as such is all-pervading pathway in physiology and pathophysiology of organisms.

  18. Elemental calcium intake associated with calcium acetate/calcium carbonate in the treatment of hyperphosphatemia

    Science.gov (United States)

    Wilson, Rosamund J; Copley, J Brian

    2017-01-01

    Background Calcium-based and non-calcium-based phosphate binders have similar efficacy in the treatment of hyperphosphatemia; however, calcium-based binders may be associated with hypercalcemia, vascular calcification, and adynamic bone disease. Scope A post hoc analysis was carried out of data from a 16-week, Phase IV study of patients with end-stage renal disease (ESRD) who switched to lanthanum carbonate monotherapy from baseline calcium acetate/calcium carbonate monotherapy. Of the intent-to-treat population (N=2520), 752 patients with recorded dose data for calcium acetate (n=551)/calcium carbonate (n=201) at baseline and lanthanum carbonate at week 16 were studied. Elemental calcium intake, serum phosphate, corrected serum calcium, and serum intact parathyroid hormone levels were analyzed. Findings Of the 551 patients with calcium acetate dose data, 271 (49.2%) had an elemental calcium intake of at least 1.5 g/day at baseline, and 142 (25.8%) had an intake of at least 2.0 g/day. Mean (95% confidence interval [CI]) serum phosphate levels were 6.1 (5.89, 6.21) mg/dL at baseline and 6.2 (6.04, 6.38) mg/dL at 16 weeks; mean (95% CI) corrected serum calcium levels were 9.3 (9.16, 9.44) mg/dL and 9.2 (9.06, 9.34) mg/dL, respectively. Of the 201 patients with calcium carbonate dose data, 117 (58.2%) had an elemental calcium intake of at least 1.5 g/day, and 76 (37.8%) had an intake of at least 2.0 g/day. Mean (95% CI) serum phosphate levels were 5.8 (5.52, 6.06) mg/dL at baseline and 5.8 (5.53, 6.05) mg/dL at week 16; mean (95% CI) corrected serum calcium levels were 9.7 (9.15, 10.25) mg/dL and 9.2 (9.06, 9.34) mg/dL, respectively. Conclusion Calcium acetate/calcium carbonate phosphate binders, taken to control serum phosphate levels, may result in high levels of elemental calcium intake. This may lead to complications related to calcium balance. PMID:28182142

  19. Mono- and Dinuclear Macrocyclic Calcium Complexes as Platforms for Mixed-Metal Complexes and Clusters.

    Science.gov (United States)

    Connolly, Emma A; Leeland, James W; Love, Jason B

    2016-01-19

    Mono- and dinuclear calcium complexes of the Schiff-base macrocycles H4L have been prepared and characterized spectroscopically and crystallographically. In the formation of Ca(THF)2(H2L(1)), Ca2(THF)2(μ-THF)(L(1)), and Ca2(THF)4(L(2)), the ligand framework adopts a bowl-shaped conformation instead of the conventional wedge, Pacman-shaped structure as seen with the anthracenyl-hinged complex Ca2(py)5(L(3)). The mononuclear calcium complex Ca(THF)2(H2L(1)) reacts with various equivalents of LiN(SiMe3)2 to form calcium/alkali metal clusters and dinuclear transition metal complexes when reacted subsequently with transition metal salts. The dinuclear calcium complex Ca2(THF)2(μ-THF)(L(1)), when reacted with various equivalents of NaOH, is shown to act as a platform for the formation of calcium/alkali metal hydroxide clusters, displaying alternate wedged and bowl-shaped conformations.

  20. Influence of maleic acid copolymers on calcium orthophosphates crystallization at low temperature

    Science.gov (United States)

    Pelin, Irina M.; Popescu, Irina; Suflet, Dana M.; Aflori, Magdalena; Bulacovschi, Victor

    2013-08-01

    The goal of this study was to investigate the maleic acid copolymers role on calcium orthophosphates crystallization at low temperature. In this respect, two maleic acid copolymers with different structures [poly(sodium maleate-co-vinyl acetate) and poly(sodium maleate-co-methyl methacrylate)] were used. The syntheses of the calcium orthophosphates in the absence and in the presence of the copolymers were performed through the wet chemical method using calcium nitrate, ammonium dihydrogen phosphate and ammonium hydroxide as reactants. The syntheses were monitored in situ by potentiometric and conductometric measurements. To ensure the transformation of less thermodynamically stable calcium orthophosphates into more stable forms, the samples were aged 30 days in mother solutions, at room temperature. The presence of the copolymers in the final products was evidenced by FTIR spectroscopy and thermogravimetric analysis. Scanning and transmission electron microscopy and laser light scattering measurements gave information about the composites morphology and the size of the formed structures. X-ray diffraction evidenced that, as a function of comonomer structure and of copolymer concentration, the products could contain hydroxyapatite with low crystallinity, calcium-deficient or carbonated hydroxyapatite. At high concentration of poly(sodium maleate-co-methyl methacrylate) the transformation of brushite into apatitic structures was inhibited.

  1. Recovery of calcium carbonate from steelmaking slag and utilization for acid mine drainage pre-treatment.

    Science.gov (United States)

    Mulopo, J; Mashego, M; Zvimba, J N

    2012-01-01

    The conversion of steelmaking slag (a waste product of the steelmaking process) to calcium carbonate (CaCO(3)) was tested using hydrochloric acid, ammonium hydroxide and carbon dioxide via a pH-swing process. Batch reactors were used to assess the technical feasibility of calcium carbonate recovery and its use for pre-treatment of acid mine drainage (AMD) from coal mines. The effects of key process parameters, such as the amount of acid (HCl/calcium molar ratio), the pH and the CO(2) flow rate were considered. It was observed that calcium extraction from steelmaking slag significantly increased with an increase in the amount of hydrochloric acid. The CO(2) flow rate also had a positive effect on the carbonation reaction rate but did not affect the morphology of the calcium carbonate produced for values less than 2 L/min. The CaCO(3) recovered from the bench scale batch reactor demonstrated effective neutralization ability during AMD pre-treatment compared with the commercial laboratory grade CaCO(3).

  2. Comparative study of calcium alginate, activated carbon, and their composite beads on methylene blue adsorption.

    Science.gov (United States)

    Hassan, A F; Abdel-Mohsen, A M; Fouda, Moustafa M G

    2014-02-15

    Three adsorbents, calcium alginate beads (AB), sodium hydroxide activated carbon based coconut shells (C), and calcium alginate/activated carbon composite beads (ACB) were prepared. Their textural properties were characterized by N2-adsorption at -196°C and scanning electron microscopy. The porosity, surface area and total pore volume of C>ACB>AB, but AB adsorbent was more acidic function groups more than the other adsorbents. Adsorption experiments were conducted to examine the effects of adsorbent dosage, pH, time, temperature and initial concentration of methylene blue. Methylene blue adsorption on C, AB and ACB was observed at pH>6 to avoid the competition of H(+). The amount of dye adsorbed increases as the adsorbent dosage increase. Adsorption of dye follows pseudo-second order mechanism. Thermodynamic studies show spontaneous and endothermic nature of the overall adsorption process.

  3. Reactive transport modeling at uranium in situ recovery sites: uncertainties in uranium sorption on iron hydroxides

    Science.gov (United States)

    Johnson, Raymond H.; Tutu, Hlanganani; Brown, Adrian; Figueroa, Linda; Wolkersdorfer, Christian

    2013-01-01

    Geochemical changes that can occur down gradient from uranium in situ recovery (ISR) sites are important for various stakeholders to understand when evaluating potential effects on surrounding groundwater quality. If down gradient solid-phase material consists of sandstone with iron hydroxide coatings (no pyrite or organic carbon), sorption of uranium on iron hydroxides can control uranium mobility. Using one-dimensional reactive transport models with PHREEQC, two different geochemical databases, and various geochemical parameters, the uncertainties in uranium sorption on iron hydroxides are evaluated, because these oxidized zones create a greater risk for future uranium transport than fully reduced zones where uranium generally precipitates.

  4. Study on the modulating effect of polysaccharide upon the mineralization of iron hydroxide

    Institute of Scientific and Technical Information of China (English)

    HUANG Jiangbo; SUN Zhenya

    2008-01-01

    To investigate the modulating effect of polysaccharide upon the mineralization of iron hydroxide, a series of simulative biomineralization experiments using dextran and chitosan as organic substrates were conducted in this paper. The results showed that iron hydroxide gel nucleated and grew in polysaccharide molecules, with the self-assemble effect of dextran or chitosan, the nanometer-sized akaganeite was formed. The shape, size and crystal structural type of iron oxyhydroxide formed from iron hydroxide gel depend on the type of polysaccharide and its concentrations.

  5. Calcium – how and why?

    Indian Academy of Sciences (India)

    J K Jaiswal

    2001-09-01

    Calcium is among the most commonly used ions, in a multitude of biological functions, so much so that it is impossible to imagine life without calcium. In this article I have attempted to address the question as to how calcium has achieved this status with a brief mention of the history of calcium research in biology. It appears that during the origin and early evolution of life the Ca2+ ion was given a unique opportunity to be used in several biological processes because of its unusual physical and chemical properties.

  6. Calcium Phosphate Biomaterials: An Update

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Current calcium phosphate (CaP) biomaterials for bone repair, substitution, augmentation and regeneration include hydroxyapatite ( HA ) from synthetic or biologic origin, beta-tricalcium phosphate ( β-TCP ) , biphasic calcium phosphate (BCP), and are available as granules, porous blocks, components of composites (CaP/polymer) cements, and as coatings on orthopedic and dental implants. Experimental calcium phosphate biomaterials include CO3- and F-substituted apatites, Mg-and Zn-substituted β-TCP, calcium phosphate glasses. This paper is a brief review of the different types of CaP biomaterials and their properties such as bioactivity, osteoconductivity, osteoinductivity.

  7. Evaluation of layered zinc hydroxide nitrate and zinc/nickel double hydroxide salts in the removal of chromate ions from solutions

    Science.gov (United States)

    de Oliveira, Henrique Bortolaz; Wypych, Fernando

    2016-11-01

    Layered zinc hydroxide nitrate (ZnHN) and Zn/Ni layered double hydroxide salts were synthesized and used to remove chromate ions from solutions at pH 8.0. The materials were characterized by many instrumental techniques before and after chromate ion removal. ZnHN decomposed after contact with the chromate solution, whereas the layered structure of Zn/Ni hydroxide nitrate (Zn/NiHN) and Zn/Ni hydroxide acetate (Zn/NiHA) remained their layers intact after the topotactic anionic exchange reaction, only changing the basal distances. ZnHN, Zn/NiHN, and Zn/NiHA removed 210.1, 144.8, and 170.1 mg of CrO42-/g of material, respectively. Although the removal values obtained for Zn/NiHN and Zn/NiHA were smaller than the values predicted for the ideal formulas of the solids (194.3 and 192.4 mg of CrO42-/g of material, respectively), the measured capacities were higher than the values achieved with many materials reported in the literature. Kinetic experiments showed the removal reaction was fast. To facilitate the solid/liquid separation process after chromium removal, Zn/Ni layered double hydroxide salts with magnetic supports were also synthesized, and their ability to remove chromate was evaluated.

  8. Urea hydrolysis and calcium carbonate reaction fronts

    Science.gov (United States)

    Fox, D. T.; Redden, G. D.; Henriksen, J.; Fujita, Y.; Guo, L.; Huang, H.

    2010-12-01

    The mobility of toxic or radioactive metal contaminants in subsurface environments can be reduced by the formation of mineral precipitates that form co-precipitates with the contaminants or that isolate them from the mobile fluid phase. An engineering challenge is to control the spatial distribution of precipitation reactions with respect to: 1) the location of a contaminant, and 2) where reactants are introduced into the subsurface. One strategy being explored for immobilizing contaminants, such as Sr-90, involves stimulating mineral precipitation by forming carbonate ions and hydroxide via the in situ, microbially mediated hydrolysis of urea. A series of column experiments have been conducted to explore how the construction or design of such an in situ reactant production strategy can affect the temporal and spatial distribution of calcium carbonate precipitation, and how the distribution is coupled to changes in permeability. The columns were constructed with silica gel as the porous media. An interval midway through the column contained an adsorbed urease enzyme in order to simulate a biologically active zone. A series of influent solutions were injected to characterize hydraulic properties of the column (e.g., bromide tracer), profiles of chemical conditions and reaction products as the enzyme catalyzes urea hydrolysis (e.g., pH, ammonia, urea), and changes that occur due to CaCO3 precipitation with the introduction of a calcium+urea solutions. In one experiment, hydraulic conductivity was reduced as precipitate accumulated in a layer within the column that had a higher fraction of fine grained silica gel. Subsequent reduction of permeability and flow (for a constant head condition) resulted in displacement of the hydrolysis and precipitation reaction profiles upstream. In another experiment, which lacked the physical heterogeneity (fine grained layer), the precipitation reaction did not result in loss of permeability or flow velocity and the reaction profile

  9. Calcium measurement methods

    Directory of Open Access Journals (Sweden)

    CarloAlberto Redi

    2010-09-01

    Full Text Available Rightly stressed by prof. Wolfgang Walz in the Preface to the series Neuromethods series, the “careful application of methods is probably the most important step in the process of scientific inquiry”. Thus, I strongly suggest to all those interested in calcium signaling and especially to the new-comers in the hot topic of neuroscience (which has so much space even in science-society debate for its implications in legal issues and in the judge-decision process to take profit from this so well edited book. I am saying this since prof. Verkhratsky and prof. Petersen......

  10. Push-out Bond Strength of Calcium Enriched Mixture Exposed to Alkaline Environment

    Directory of Open Access Journals (Sweden)

    Sobhnamayan F

    2015-09-01

    Full Text Available Statement of Problem: Calcium hydroxide which is commonly used as an intracanal medicament, changes the pH of dentin and periradicular tissues to an alkaline pH. In some clinical situations, endodontic reparative cements like calcium enriched mixture cement are used after calcium hydroxide therapy. However, the alkaline pH may affect the physical properties of this cement. Objectives: This study was designed to evaluate the effect of alkaline pH on the push-out bond strength of calcium enriched mixture. Materials and Methods: 80 root slices were prepared from single-rooted human teeth and their lumens were instrumented to achieve a diameter of 1.3mm. Calcium enriched mixture (CEM was mixed according to the manufacturer’s instruction and introduced into the lumens of root slices. The specimens were then randomly divided into 4 groups (n = 20 and wrapped in pieces of gauze soaked in synthetic tissue fluid (STF buffered in potassium hydroxide at pH values of 7.4, 8.4, 9.4, or 10.4. The samples were incubated for 4 days at 37°C. The push-out bond strengths were then measured using a universal testing machine. Failure modes were examined under a light microscope at ×20 magnification. The data were analyzed using one-way analysis of variance and Tukey’s post hoc tests. Results: The greatest (1.41 ± 0.193 MPa and lowest (0.8 ± 0.06 MPa mean push-out bond strengths were observed after exposure to pH values of 7.4 and 8.4, respectively. There were significant differences between the neutral group and the groups with pH of 8.4 (p = 0.008 and 10.4 (p = 0.022. The bond failure was predominantly of cohesive type for all experimental groups. Conclusions: Under the condition of this study, alkaline pH adversely affected the Push-out bond strength of CEM cement.

  11. Revascularization of an Immature Tooth with Apical Periodontitis Using Calcium Hydroxide: A 3-year Follow-up

    OpenAIRE

    Silva, Mauro Henrique Chagas; CAMPOS, CELSO NEIVA; Coelho, Marcelo Santos

    2015-01-01

    Root canal treatment of teeth presenting immature development is a great challenge for both the patient and the professional. The thinness of the root canal walls of immature teeth may lead to root fracture and thus the outcomes of such treatments are uncertain. Revascularization is based on root canal decontamination followed by the induction of blood migration from the periapical tissues and the development of new vascular tissue in the canal space. The principle of disinfection in regenera...

  12. Impact of co-pretreatment of calcium hydroxide and steam explosion on anaerobic digestion efficiency with corn stover.

    Science.gov (United States)

    Ji, Jinli; Zhang, Jiyu; Yang, Liutianyi; He, Yanfeng; Zhang, Ruihong; Liu, Guangqing; Chen, Chang

    2016-09-29

    Anaerobic digestion (AD) is an effective way to utilize the abundant resource of corn stover (CS). In this light, Ca(OH)2 pretreatment alone, steam explosion (SE) pretreatment alone, and co-pretreatment of Ca(OH)2 and SE were applied to improve the digestion efficiency of CS. Results showed that AD of co-pretreated CS with 1.0% Ca(OH)2 and SE at 1.5 MPa achieved the highest cumulative methane yield of [Formula: see text], which was 61.54% significantly higher (p pretreatment enhanced from 43.03% to 69.52%. Methane yield could be well fitted by the first-order model and the modified Gompertz model. In addition, composition and structural changes of CS after pretreatment were analyzed by a fiber analyzer, scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray diffraction. The validated results indicated that co-pretreatment of Ca(OH)2 and SE was efficient to improve the digestion performance of CS and might be a suitable method for agricultural waste pretreatment in the future AD industry.

  13. Effect of Cr on the passive film formation mechanism of steel rebar in saturated calcium hydroxide solution

    Science.gov (United States)

    Liu, Ming; Cheng, Xuequn; Li, Xiaogang; Pan, Yue; Li, Jun

    2016-12-01

    Passive films grow on the surface of Cr-modified steels subjected to saturated Ca(OH)2 solution. Electrochemical techniques, such as measurement of open circuit potentials, polarization curves, and electrochemical impedance spectroscopy combined with X-ray photoelectron spectrometer and auger electron spectroscopy, were applied to study the influence of low Cr content on the passive film formation mechanism of steel rebar in saturated Ca(OH)2 solution. Results show that Cr inhibits the formation of passive film at the beginning of its formation. Corrosion current density decreases and polarization resistance increases with the extension of the immersion time. A stable passive film takes at least three days to form. The passive film resistance of HRB400 carbon steel is higher than that of Cr-modified steels in the early stage of immersion (72 h), and Cr promotes the formation of a denser and more compact passive film. The stable passive film is primarily made up of iron oxides with a thickness of 5-6 nm. Cr are involved in the formation of passive films, thereby resulting in a film that consists of an inner layer that contains Cr-Fe oxides and an outer layer that contains Fe oxides, whose thickness presents a slight increase as the content of Cr increases.

  14. Extracellular calcium sensing and extracellular calcium signaling

    Science.gov (United States)

    Brown, E. M.; MacLeod, R. J.; O'Malley, B. W. (Principal Investigator)

    2001-01-01

    , localized changes in Ca(o)(2+) within the ECF can originate from several mechanisms, including fluxes of calcium ions into or out of cellular or extracellular stores or across epithelium that absorb or secrete Ca(2+). In any event, the CaR and other receptors/sensors for Ca(o)(2+) and probably for other extracellular ions represent versatile regulators of numerous cellular functions and may serve as important therapeutic targets.

  15. Clogging and Cementation Caused by Calcium or Iron Biogrouts

    Science.gov (United States)

    Ivanov, V.; Chu, J.; Naeimi, M.

    2012-12-01

    Chemical grouts are often used to reduce the hydraulic conductivity of soil for seepage control purposes. However, chemical grouts can be expensive and environmentally unfriendly. Therefore, two new biogrouts were tested for their bioclogging and biocementation properties. The first was calcium-based biogrout, which contained urease-producing bacteria, calcium chloride and urea for the crystallization of calcite due to enzymatic hydrolysis of urea. The second was iron-based biogrout, which consisted of urease-producing bacteria, ferric chelate, and urea for the precipitation of ferric hydroxide and carbonate due to enzymatic hydrolysis of urea. The permeability of sand (P, 10^-5 m/s), treated with calcium-based biogrout, linearly decreased as a function of the content of precipitated calcium (C, % w/w) according to the following equation: P = 5.1 - 4.0 C. Meanwhile, the permeability of sand treated with iron-based biogrout dropped to 2.7x10^-6 m/s at content of precipitated iron (F, % w/w) about 0.35 % w/w , by the equation: P = 5.1 - 14.6 F , and then slowly decreased to 1.4x10^-7 m/s at content of precipitated iron 1.8% w/w by the following equation: P = 0.36 - 0.23F. Both biogrouts have approximately same efficiency in the reduction of permeability of sand to low values. However, the mechanisms of bioclogging are probably different because the reduction of permeability by calcium-based biogrout was described by linear function of precipitated calcium but the reduction of permeability by iron-based biogrout showed two steps of the clogging. Different functions and mechanisms were related probably to the different type of precipitates. The images of biogrouted sand samples show that calcium-based biogrout produced white amorphous or crystallised calcium carbonate, while iron-based biogrout produced gel-like brown precipitate without visible crystals. The unconfined compressive strengths of the sand treated with different biogrouts (Y, kPa) increased by power

  16. Vitamin D, Calcium, and Bone Health

    Science.gov (United States)

    ... in Balance › Vitamin D, Calcium, and Bone Health Vitamin D, Calcium, and Bone Health March 2012 Download ... also helps keep your bones strong. Why are vitamin D and calcium important to bone health? Vitamin ...

  17. Calcium, vitamin D, and your bones

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/patientinstructions/000490.htm Calcium, vitamin D, and your bones To use the sharing ... and maintain strong bones. How Much Calcium and Vitamin D do I Need? Amounts of calcium are ...

  18. A Ni-Fe Layered Double Hydroxide-Carbon Nanotube Complex for Water Oxidation

    CERN Document Server

    Gong, Ming; Wang, Hailiang; Liang, Yongye; Wu, Justin Zachary; Zhou, Jigang; Wang, Jian; Regier, Tom; Wei, Fei; Dai, Hongjie

    2013-01-01

    Highly active, durable and cost-effective electrocatalysts for water oxidation to evolve oxygen gas hold a key to a range of renewable energy solutions including water splitting and rechargeable metal-air batteries. Here, we report the synthesis of ultrathin nickel iron layered double hydroxide nanoplates on mildly oxidized multi-walled carbon nanotubes. Incorporation of Fe into the nickel hydroxide induced the formation of NiFe-layered double hydroxide. The nanoplates were covalently attached to a network of nanotubes, affording excellent electrical wiring to the nanoplates. The ultra-thin Ni-Fe layered double hydroxide nanoplates/carbon nanotube complex was found to exhibit unusually high electro-catalytic activity and stability for oxygen evolution and outperformed commercial precious metal Ir catalysts.

  19. Waste metal hydroxide sludge as adsorbent for a reactive dye.

    Science.gov (United States)

    Santos, Sílvia C R; Vílar, Vítor J P; Boaventura, Rui A R

    2008-05-30

    An industrial waste sludge mainly composed by metal hydroxides was used as a low-cost adsorbent for removing a reactive textile dye (Remazol Brilliant Blue) in solution. Characterization of this waste material included chemical composition, pH(ZPC) determination, particle size distribution, physical textural properties and metals mobility under different pH conditions. Dye adsorption equilibrium isotherms were determined at 25 and 35 degrees C and pH of 4, 7 and 10 revealing reasonably fits to Langmuir and Freundlich models. At 25 degrees C and pH 7, Langmuir fit indicates a maximum adsorption capacity of 91.0mg/g. An adsorptive ion-exchange mechanism was identified from desorption studies. Batch kinetic experiments were also conducted at different initial dye concentration, temperature, adsorbent dosage and pH. A pseudo-second-order model showed good agreement with experimental data. LDF approximation model was used to estimate homogeneous solid diffusion coefficients and the effective pore diffusivities. Additionally, a simulated real effluent containing the selected dye, salts and dyeing auxiliary chemicals, was also used in equilibrium and kinetic experiments and the adsorption performance was compared with aqueous dye solutions.

  20. Reactions of cumene hydroperoxide mixed with sodium hydroxide.

    Science.gov (United States)

    Hou, Hung-Yi; Shu, Chi-Min; Tsai, Tung-Lin

    2008-04-15

    Decomposition of cumene hydroperoxide (CHP) was undertaken in a free radical chain reaction. The peroxyl group is very active and unstable, while the remainder of the molecule is inert. CHP reacted with various concentrations of dilute sodium hydroxide as a catalyst to cleave at ambient and decomposition temperature. The products were verified by GC/MS, and were quantitatively analyzed by chromatography. CHP cleaved heterolytic with NaOH at 250 degrees C, whose major product was dimethylphenyl carbinol (DMPC); however, the main products become acetophenone and alpha-methylstyrene by cleaved homolytic pathway. The catalytic concentrations of NaOH significantly affected the branch ratios of DMPC under decomposition. Based on the experimental results, a radical cleavage mechanism was proposed. To sum up, the reaction parameters, such as temperature, Lewis base, etc., could affect the incompatibilities and decomposition pathways for proper CHP cleavage process. In addition, exothermic onset temperatures (T0) and heat of decomposition (Delta Hd) of incompatible mixtures and CHP itself were studied by differential scanning calorimetry (DSC). Comparisons of T0, Delta Hd and peak power were assessed to corroborate the severity of thermal hazards. From the decay rate of CHP concentration, the reaction order was determined to be 0.5, and the Arrhenius parameters were measured as Ea=92.1 kJ/mol and frequency factor A=2.42 x 10(10)min(-1).

  1. Layered-double-hydroxide-modified electrodes: electroanalytical applications.

    Science.gov (United States)

    Tonelli, Domenica; Scavetta, Erika; Giorgetti, Marco

    2013-01-01

    Two-dimensional inorganic solids, such as layered double hydroxides (LDHs), also defined as anionic clays, have open structures and unique anion-exchange properties which make them very appropriate materials for the immobilization of anions and biomolecules that often bear an overall negative charge. This review aims to describe the important aspects and new developments of electrochemical sensors and biosensors based on LDHs, evidencing the research from our own laboratory and other groups. It is intended to provide an overview of the various types of chemically modified electrodes that have been developed with these 2D layered materials, along with the significant advances made over the last several years. In particular, we report the main methods used for the deposition of LDH films on different substrates, the conductive properties of these materials, the possibility to use them in the development of membranes for potentiometric anion analysis, the early analytical applications of chemically modified electrodes based on the ability of LDHs to preconcentrate redox-active anions and finally the most recent applications exploiting their electrocatalytic properties. Another promising application field of LDHs, when they are employed as host structures for enzymes, is biosensing, which is described considering glucose as an example.

  2. Mechanochemical synthesis of low-fluorine doped aluminum hydroxide fluorides

    Science.gov (United States)

    Scalise, V.; Scholz, G.; Kemnitz, E.

    2016-11-01

    Different aluminum hydroxide fluorides with varying Al/F molar ratios from 1:1.5 up to 1:0.05 were successfully synthesized by mechanochemical reactions. The characterization of the products by XRD, 27Al and 19F MAS NMR, thermal analysis, nitrogen adsorption and zeta potential techniques allows a detailed understanding of the structure and surface properties of the products. Using γ-Al(OH)3 and β-AlF3·3H2O as OH- and F-sources, respectively, strongly disordered products were obtained with an Al: F molar ratio higher than 1:0.25. The fluorination degree has affected the amount of 4- and 5-fold coordinated Al sites, not present in the reactants. An evolution of the sub-coordinated Al-species has been detected also as a consequence of annealing processes. Obviously, these species affect the phase transition to alumina, by decreasing the transition temperature of the formation of α-Al2O3. Synthesis conditions (milling time, fluorination degree) play a crucial role for the product composition.

  3. Surface modification of magnesium hydroxide using vinyltriethoxysilane by dry process

    Science.gov (United States)

    Lan, Shengjie; Li, Lijuan; Xu, Defang; Zhu, Donghai; Liu, Zhiqi; Nie, Feng

    2016-09-01

    In order to improve the compatibility between magnesium hydroxide (MH) and polymer matrix, the surface of MH was modified using vinyltriethoxysilane (VTES) by dry process and the interfacial interaction between MH and VTES was also studied. Zeta potential measurements implied that the MH particles had better dispersion and less aggregation after modification. Sedimentation tests showed that the surface of MH was transformed from hydrophilic to hydrophobic, and the dispersibility and the compatibility of MH particles significantly improved in the organic phase. Scanning electronic microscopy (SEM), Transmission electron microscopy (TEM) and X-ray powder diffraction (XRD) analyses showed that a thin layer had formed on the surface of the modified MH, but did not alter the material's crystalline phase. Fourier transform infrared (FT-IR) spectra, X-ray photoelectron spectra (XPS) and Thermogravimetric analysis (TGA) showed that the VTES molecules bound strongly to the surface of MH after modification. Chemical bonds (Sisbnd Osbnd Mg) formed by the reaction between Si-OC2H5 and hydroxyl group of MH, also there have physical adsorption effect in the interface simultaneously. A modification mechanism of VTES on the MH surface by dry process was proposed, which different from the modification mechanism by wet process.

  4. Atomistic Simulations of Uranium Incorporation into Iron (Hydr)Oxides

    Energy Technology Data Exchange (ETDEWEB)

    Kerisit, Sebastien N.; Felmy, Andrew R.; Ilton, Eugene S.

    2011-04-29

    Atomistic simulations were carried out to characterize the coordination environments of U incorporated in three Fe-(hydr)oxide minerals: goethite, magnetite, and hematite. The simulations provided information on U-O and U-Fe distances, coordination numbers, and lattice distortion for U incorporated in different sites (e.g., unoccupied versus occupied sites, octahedral versus tetrahedral) as a function of the oxidation state of U and charge compensation mechanisms (i.e., deprotonation, vacancy formation, or reduction of Fe(III) to Fe(II)). For goethite, deprotonation of first shell hydroxyls enables substitution of U for Fe(III) with a minimal amount of lattice distortion, whereas substitution in unoccupied octahedral sites induced appreciable distortion to 7-fold coordination regardless of U oxidation states and charge compensation mechanisms. Importantly, U-Fe distances of ~3.6 Å were associated with structural incorporation of U and cannot be considered diagnostic of simple adsorption to goethite surfaces. For magnetite, the octahedral site accommodates U(V) or U(VI) with little lattice distortion. U substituted for Fe(III) in hematite maintained octahedral coordination in most cases. In general, comparison of the simulations with available experimental data provides further evidence for the structural incorporation of U in iron (hydr)oxide minerals.

  5. Enhanced aerobic sludge granulation with layered double hydroxide

    Directory of Open Access Journals (Sweden)

    Jizhi Zhou

    2014-06-01

    Full Text Available Aerobic granular sludge technology has been developed for the biochemical treatment of wastewater in the present study. A fast cultivation of aerobic granular sludge was realized in Sequencing Batch Reactor (SBR, where Mg-Al layered double hydroxide (LDH was used as a carrier for granules growth. In comparison, the sludge particle size with LDH addition was bigger than those without LDH, with more than 50% of compact granular sludge >1.4 mm in size. This indicatestheLDH improved the growth ofthegranular sludge. The frequency of LDH addition had little effect on the granule growth. Moreover, the formation of granules led to the low sludge volume index (SVI and high mixed liquid suspended solids (MLSS in SBR reactor. With the formation of granular sludge, more than 80% of COD was removed in SBR reactor. The high COD removal efficiency of wastewater was observed regardless of various COD loading strength. The results suggest that the growth of granular sludge with LDH as a carrier enhanced the treatment efficiency. Therefore, our results have provided a promising way to prepare the granular sludge for wastewater treatment.

  6. Lithium adsorption on amorphous aluminum hydroxides and gibbsite

    Directory of Open Access Journals (Sweden)

    Konstantinos P. Prodromou

    2016-01-01

    Full Text Available Lithium (Li adsorption on both amorphous aluminum hydroxides and gibbsite was studied. For the amorphous Al(OH3 the adsorption was found to be pH dependent. Generally, 1.6 times more Li was adsorbed at initial pH value 8.0 compared with pH value 6.50. Gibbsite adsorbed 11.6 to 45.5 times less Li quantities compared with amorphous Al(OH3. Lithium adsorption was not depended on equilibrium times. It remained stable for all equilibrium times used. Lithium quantities extracted with 1N CH3COONH4 pH 7 , represent the physical adsorption, while the remaining Li that was adsorbed on Al(OH3, represents the chemical adsorption. During the desorption process 19% of Li extracted with NH4+, represents the physical adsorption, while the remaining 81% of Li, which was adsorbed represents the chemical adsorption. In gibbsite, 9.6% of Li represents the physical adsorption and 90.4% the chemical one. The experimental data conformed well to Freundlich isotherm equation.

  7. Defluoridation from aqueous solutions by granular ferric hydroxide (GFH).

    Science.gov (United States)

    Kumar, Eva; Bhatnagar, Amit; Ji, Minkyu; Jung, Woosik; Lee, Sang-Hun; Kim, Sun-Joon; Lee, Giehyeon; Song, Hocheol; Choi, Jae-Young; Yang, Jung-Seok; Jeon, Byong-Hun

    2009-02-01

    This research was undertaken to evaluate the feasibility of granular ferric hydroxide (GFH) for fluoride removal from aqueous solutions. Batch experiments were performed to study the influence of various experimental parameters such as contact time (1 min-24h), initial fluoride concentration (1-100 mgL(-1)), temperature (10 and 25 degrees C), pH (3-12) and the presence of competing anions on the adsorption of fluoride on GFH. Kinetic data revealed that the uptake rate of fluoride was rapid in the beginning and 95% adsorption was completed within 10 min and equilibrium was achieved within 60 min. The sorption process was well explained with pseudo-first-order and pore diffusion models. The maximum adsorption capacity of GFH for fluoride removal was 7.0 mgg(-1). The adsorption was found to be an endothermic process and data conform to Langmuir model. The optimum fluoride removal was observed between pH ranges of 4-8. The fluoride adsorption was decreased in the presence of phosphate followed by carbonate and sulphate. Results from this study demonstrated potential utility of GFH that could be developed into a viable technology for fluoride removal from drinking water.

  8. Immobilization of Penicillin G Acylase on Calcined Layered Double Hydroxides

    Institute of Scientific and Technical Information of China (English)

    REN Ling-ling; HE Jing; Evans D. G.; DUAN Xue

    2003-01-01

    A hydrotalcite-like Mg2+/Al3+ layered double hydroxide(LDH) material was prepared by means of a modified coprecipitation method involving a rapid mixing step followed by a separate aging process. LDH calcined at 500 ℃, denoted as CLDH, was characterized by XRD, IR and BET surface area measurements. CLDH has a poor crystalline MgO-like structure with a high surface area and porosity. CLDH was used as a support for the immobilization of penicillin G acylase(PGA). The effect of varying the immobilization conditions, such as pH, contact time and the ratio of enzyme to support, on the activity of the immobilized enzyme in the hydrolysis of penicillin G has been studied. It was found that the activity of the immobilized enzyme decreased slightly with decreasing pH and reached a maximum after a contact time of 24 h. The activity of the immobilized enzyme increased with increasing the ratio of enzyme to support. It was found that the adsorption of PGA inhibited the expected reaction of CLDH with an aqueous medium to regenerate a LDH phase. Its original activity(36%) after 15 cycles of reuse of the immobilized enzyme was retained, but no further loss in the activity was observed.

  9. In vivo toxicity studies of europium hydroxide nanorods in mice.

    Science.gov (United States)

    Patra, Chitta Ranjan; Abdel Moneim, Soha S; Wang, Enfeng; Dutta, Shamit; Patra, Sujata; Eshed, Michal; Mukherjee, Priyabrata; Gedanken, Aharon; Shah, Vijay H; Mukhopadhyay, Debabrata

    2009-10-01

    Lanthanide nanoparticles and nanorods have been widely used for diagnostic and therapeutic applications in biomedical nanotechnology due to their fluorescence and pro-angiogenic properties to endothelial cells, respectively. Recently, we have demonstrated that europium (III) hydroxide [Eu(III)(OH)(3)] nanorods, synthesized by the microwave technique and characterized by several physico-chemical techniques, can be used as pro-angiogenic agents which introduce future therapeutic treatment strategies for severe ischemic heart/limb disease, and peripheral ischemic disease. The toxicity of these inorganic nanorods to endothelial cells was supported by several in vitro assays. To determine the in vivo toxicity, these nanorods were administered to mice through intraperitoneal injection (IP) everyday over a period of seven days in a dose dependent (1.25 to 125 mg kg(-1) day(-1)) and time dependent manner (8-60 days). Bio-distribution of europium elements in different organs was analyzed by inductively coupled plasma mass spectrometry (ICPMS). Short-term (S-T) and long-term (L-T) toxicity studies (mice euthanized on days 8 and 60 for S-T and L-T, respectively) show normal blood hematology and serum clinical chemistry with the exception of a slight elevation of liver enzymes. Histological examination of nanorod-treated vital organs (liver, kidney, spleen and lungs) showed no or only mild histological changes that indicate mild toxicity at the higher dose of nanorods.

  10. Methotrexate intercalated ZnAl-layered double hydroxide

    Science.gov (United States)

    Chakraborty, Manjusha; Dasgupta, Sudip; Soundrapandian, Chidambaram; Chakraborty, Jui; Ghosh, Swapankumar; Mitra, Manoj K.; Basu, Debabrata

    2011-09-01

    The anticancerous drug methotrexate (MTX) has been intercalated into an ZnAl-layered double hydroxide (LDH) using an anion exchange technique to produce LDH-MTX hybrids having particle sizes in the range of 100-300 nm. X-ray diffraction studies revealed increases in the basal spacings of ZnAl-LDH-MTX hybrid on MTX intercalation. This was corroborated by the transmission electron micrographs, which showed an increase in average interlayer spacing from 8.9 Å in pristine LDH to 21.3 Å in LDH-MTX hybrid. Thermogravimetric analyses showed an increase in the decomposition temperature for the MTX molecule in the LDH-MTX hybrid indicating enhanced thermal stability of the drug molecule in the LDH nanovehicle. The cumulative release profile of MTX from ZnAl-LDH-MTX hybrids in phosphate buffer saline (PBS) at pH 7.4 was successfully sustained for 48 h following Rigter-Peppas model release kinetics via diffusion.

  11. Bionanocomposites based on layered double hydroxides as drug delivery systems

    Science.gov (United States)

    Aranda, Pilar; Alcântara, Ana C. S.; Ribeiro, Ligia N. M.; Darder, Margarita; Ruiz-Hitzky, Eduardo

    2012-10-01

    The present work introduces new biohybrid materials involving layered double hydroxides (LDH) and biopolymers to produce bionanocomposites, able to act as effective drug delivery systems (DDS). Ibuprofen (IBU) and 5-aminosalicylic acid (5-ASA) have been chosen as model drugs, being intercalated in a Mg-Al LDH matrix. On the one side, the LDHIBU intercalation compound prepared by ion-exchange reaction was blended with the biopolymers zein, a highly hydrophobic protein, and alginate, a polysaccharide widely applied for encapsulating drugs. On the other side, the LDH- 5-ASA intercalation compound prepared by co-precipitation was assembled to the polysaccharides chitosan and pectin, which show mucoadhesive properties and resistance to acid pH values, respectively. Characterization of the intercalation compounds and the resulting bionanocomposites was carried out by means of different experimental techniques: X-ray diffraction, infrared spectroscopy, chemical and thermal analysis, as well as optical and scanning electron microscopies. Data on the swelling behavior and drug release under different pH conditions are also reported.

  12. Surface modification of magnesium hydroxide by γ-aminopropyltriethoxysilane

    Institute of Scientific and Technical Information of China (English)

    LUO Wei; FENG Qi-ming; OU Le-ming; LIU Kun

    2008-01-01

    Magnesium hydroxide (MH), which is commonly used as a halogen-free flame retardant filler in composite materials, was modified by silanization reaction with γ-aminopropyltriethoxysilane (γ-APS) in aqueous solution at different pH values (pH range from 8.0 to 12.0). The surface properties of grafted γ-APS on MH surface as a function of solution pH value were studied using elemental analysis, Fourier transform infrared spectroscopy and zeta potential measurement. The results show that hydrolysis and condensation of γ-APS are activated in alkaline solution and lead to multilayer adsorption of γ-APS molecules on the surface of MH. The type of adsorption orientation of γ-APS on MH surface is a function of coverage density that is altered by changing solution pH value. At low coverage density (e.g.55nm-2), γ-APS molecules are preferentially adsorbed to the surface with the silicon moiety towards the surface, and increasing coverage density (e.g.90nm-2) leads to parallel orientation. At an even higher coverage density(e.g.115nm-2), γ-APS molecules bond to the surface with the amino moiety towards the surface.

  13. CRACK2 - Modelling calcium carbonate deposition from bicarbonate solution in cracks in concrete

    Energy Technology Data Exchange (ETDEWEB)

    Brodersen, K

    2003-03-01

    The numerical CRACK2 model simulates precipitation of calcite from calcium bicarbonate solution (e.g. groundwater) passing through cracks in concrete or other cementitious materials. A summary of experimental work is followed by a detailed description of the model. Hydroxyl ions are transported by diffusion in pore systems in columns of cementitious materials. The hydroxyl is precipitating calcite from a flow of bicarbonate solution in a crack connecting the ends of a row of such columns. The cementitious material is simulated as calcium hydroxide mixed with inert material but with sodium hydroxide dissolved in the pore solution. Diffusive migration of cesium as radioactive isotope is also considered. Electrical interaction of the migrating ions is taken into account. Example calculations demonstrate effects of parameter variations on distribution of precipitated calcite in the crack and on the composition of the outflowing solution, which can be compared directly with experimental results. Leaching behavior of sodium can be used to tune the model to experimental observations. The calcite is mostly precipitated on top of the original crack surface and may under certain circumstances fill the crack. The produced thin layers of low porosity calcite act as a diffusion barrier limiting contact between cement and solution. Pore closure mechanisms in such layers are discussed. Implications for safety assessment of radioactive waste disposal are shortly mentioned. The model is also relevant for conventional uses of concrete. (au)

  14. Mixing Acid Salts and Layered Double Hydroxides in Nanoscale under Solid Condition

    OpenAIRE

    2014-01-01

    The immobilization of potassium sorbate, potassium aspartate and sorbic acid in layered double hydroxide under solid condition was examined. By simply mixing two solids, immobilization of sorbate and aspartate in the interlayer space of nitrate-type layered double hydroxide, so called intercalation reaction, was achieved, and the uptakes, that is, the amount of immobilized salts and the interlayer distances of intercalation compounds were almost the same as those obtained in aqueous solution...

  15. Coordination Structure of Aluminum in Magnesium Aluminum Hydroxide Studied by 27Al NMR

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The coordination structure of aluminum in magnesium aluminum hydroxide was studiedby 27Al NMR. The result showed that tetrahedral aluminum (AlⅣ) existed in magnesiumaluminum hydroxide, and the contents of AlⅣ increased with the increase of the ratio of Al/Mg andwith the peptizing temperature. AlⅣ originated from the so-called Al13 polymer with the structureof one Al tetrahedron surrounded by twelve Al octahedrons.

  16. Layered double hydroxides as containers of inhibitors in organic coatings for corrosion protection of carbon steel

    OpenAIRE

    Hang, To Thi Xuan; Truc, Trinh Anh; Duong, Nguyen Thuy; Pébère, Nadine; Olivier, Marie-Georges

    2012-01-01

    International audience; The present work focuses on the use of layered double hydroxides (LDH) as containers for corrosion inhibitors in an epoxy coating. 2-Benzothiazolylthio-succinic acid (BTSA), used as corrosion inhibitor, was intercalated by co-precipitation in magnesium-aluminum layered double hydroxides. The obtained LDH-BTSA was characterized by infrared spectroscopy, X-ray diffraction and scanning electron microscopy. BTSA release from LDH-BTSA in NaCl solutions was investigated by U...

  17. Vitamin D and Intestinal Calcium Absorption

    OpenAIRE

    Christakos, Sylvia; Dhawan, Puneet; Porta, Angela; Mady, Leila J.; Seth, Tanya

    2011-01-01

    The principal function of vitamin D in calcium homeostasis is to increase calcium absorption from the intestine. Calcium is absorbed by both an active transcellular pathway, which is energy dependent, and by a passive paracellular pathway through tight junctions. 1,25Dihydroxyvitamin D3 (1,25(OH)2D3) the hormonally active form of vitamin D, through its genomic actions, is the major stimulator of active intestinal calcium absorption which involves calcium influx, translocation of calcium throu...

  18. Mammary-Specific Ablation of the Calcium-Sensing Receptor During Lactation Alters Maternal Calcium Metabolism, Milk Calcium Transport, and Neonatal Calcium Accrual

    OpenAIRE

    Mamillapalli, Ramanaiah; VanHouten, Joshua; Dann, Pamela; Bikle, Daniel; Chang, Wenhan; Brown, Edward; Wysolmerski, John

    2013-01-01

    To meet the demands for milk calcium, the lactating mother adjusts systemic calcium and bone metabolism by increasing dietary calcium intake, increasing bone resorption, and reducing renal calcium excretion. As part of this adaptation, the lactating mammary gland secretes PTHrP into the maternal circulation to increase bone turnover and mobilize skeletal calcium stores. Previous data have suggested that, during lactation, the breast relies on the calcium-sensing receptor (CaSR) to coordinate ...

  19. Effect of calcium on adsorptive removal of As(III) and As(V) by iron oxide-based adsorbents

    KAUST Repository

    Uwamariya, V.

    2014-06-25

    The effects of calcium on the equilibrium adsorption capacity of As(III) and As(V) onto iron oxide-coated sand (IOCS) and granular ferric hydroxide (GFH) were investigated through batch experiments, rapid small-scale column tests (RSSCT) and kinetics modelling. Batch experiments showed that at calcium concentrations≤20 mg/L, high As(III) and As(V) removal efficiencies by IOCS and GFH are achieved at pH 6. An increase of the calcium concentration to 40 and 80 mg/L reversed this trend, giving higher removal efficiencies at higher pH (8). The adsorption capacities of IOCS and GFH at an equilibrium arsenic concentration of 10 g/L were found to be between 2.0 and 3.1 mg/g for synthetic water without calcium and between 2.8 and 5.3 mg/g when 80 mg/L of calcium was present at the studied pH values. After 10 hours of filter run in RSSCT, approximately 1000 empty bed volumes, the ratios of C/Co for As(V) were 26% and 18% for calcium-free model water; and only 1% and 0.2% after addition of 80 mg/L of Ca for filter columns with IOCS and GFH, respectively. The adsorption of As(III) and As(V) onto GFH follows a second-order reaction, with and without addition of calcium. The adsorption of As(III) and As(V) onto IOCS follows a first-order reaction without calcium addition, and moves to the second-reaction-order kinetics when calcium is added. Based on the intraparticle diffusion model, the main controlling mechanism for As(III) adsorption is intraparticle diffusion, while surface diffusion contributes greatly to the adsorption of As(V).

  20. New methodologies for the conservation of cultural heritage: micellar solutions, microemulsions, and hydroxide nanoparticles.

    Science.gov (United States)

    Giorgi, Rodorico; Baglioni, Michele; Berti, Debora; Baglioni, Piero

    2010-06-15

    of calcium hydroxide nanoparticles for the consolidation of works of art. In this Account, we highlight how conservation science can benefit from the conceptual and the methodological background derived from both soft (microemulsions and micelles for cleaning) and hard (nanoparticles for consolidation) nanoscience. A combination of different nanotechnologies allows today's conservators to provide, in each restoration step, interventions respectful of the physicochemical characteristics of the materials used by artists. The "palette" of methods provided by nanoscience is continuously enriching the field, and the development of novel nanomaterials and the study of nanoscale physicochemical phenomena will further improve the performance of restoration formulations and our comprehension of degradation mechanisms.

  1. Parametric Effect of Sodium Hydroxide and Sodium Carbonate on the Potency of a Degreaser

    Directory of Open Access Journals (Sweden)

    Babatope Abimbola Olufemi

    2016-01-01

    Full Text Available Normal 0 false false false EN-US X-NONE X-NONE Experimental and statistical analysis was carried out on the comparative effect of sodium hydroxide and sodium carbonate on the potency of a laboratory produced degreaser in this work. The materials used include; octadecyl benzene sulphonic acid, sodium hydroxide, sodium carbonate, sodium metasilicate, carboxyl methyl cellulose (C.M.C, formadelhyde, perfume, colourant and distilled water. Different samples of degreaser were produced with varying composition of sodium hydroxide and sodium carbonate respectively. Statistical significance through methods like analysis of variance (ANOVA of some parameters on various concentrations of sodium hydroxide and sodium carbonate was investigated. The effect of the varying compositions of sodium hydroxide and sodium carbonate was also determined by using a gray scale (GS test, and also subjecting surfaces heavily stained with crude oil to determine and characterize the cleansing action of the degreaser. It was found that as the concentration of sodium hydroxide increases, the cleansing ability also increases, whereas the increase in concentration of sodium carbonate had no effect on the cleansing ability. The work would enable production of effective, useful and property controlled degreasers at moderate cost.

  2. Scientific Opinion on the safety and efficacy of sodium hydroxide for dogs, cats and ornamental fish

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Additives and Products or Substances used in Animal Feed (FEEDAP

    2012-10-01

    Full Text Available

    The additive consists, by specification, of a minimum of 98.0 % sodium hydroxide or alkali in the solid form, the content of solutions scaled accordingly, based on the stated or labelled concentration. No data have been provided that would support the specification of the solid form, only a 50.0 % w/w solution of sodium hydroxide in water, which is the final product of the production process described in the dossier. Sodium hydroxide is considered safe for the target animals, provided that the resulting total sodium concentration in feed does not compromise the overall electrolyte balance. Sodium hydroxide in solid form and in aqueous solution at concentrations > 8.0 % is corrosive. At lower concentrations it is irritant to skin and eyes (0.5 % and 0.2 %, respectively and the respiratory tract (0.5 %. Exposure via inhalation is likely to be minimal. Sodium hydroxide is not considered to be a skin sensitiser. As sodium hydroxide is used in food as an acidity regulator, and its function in feed is essentially the same as that in food, no further demonstration of efficacy is necessary.

  3. Adsorption of hydrated hydroxide and hydronium ions on Ag(1 1 1). A quantum mechanical investigation

    Science.gov (United States)

    Patrito, E. M.; Paredes-Olivera, P.

    2003-03-01

    In this paper we have studied comparatively the adsorption of hydroxide and hydronium ions, extending our previous study on hydronium adsorption [J. Phys. Chem. B. 105 (2001) 7227] and emphasizing the adsorption of hydroxide. The calculations were performed on the 111 surface of silver using ab initio quantum mechanical methods (Hartree-Fock+Moller-Plesset second order perturbation theory). The adsorption was investigated for the bare and the hydrated ions (up to three water molecules). Binding energies, equilibrium structures and charge transfer processes were investigated. While the successive hydration of hydronium detaches the ion from the surface, the hydrated hydroxide anion remains specifically adsorbed. Charge transfer processes between the adsorbates and the surface were studied using electron density difference plots and effective charges obtained from Mulliken populations and from surface-dipole moment curves. The energetics of the surface reactions leading to the formation of the hydrated hydronium and hydroxide ions from the bare adsorbed ions and water molecules was also investigated. Both reactions are exothermic mainly due to the formation of strong hydrogen bonds. The effect of an external homogeneous electric field perpendicular to the surface on different adsorbate properties was investigated for the bare and hydrated hydroxide ion in order to model the environment of the electrical double layer. The electric field affects the orientation of the water molecules on the surface and the hydroxide surface distance.

  4. Cadmium hydroxide and oxide nanoporous walls with high performance photocatalytic properties

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Yu-Cheng, E-mail: ychang0127@gmail.com

    2015-07-15

    Highlights: • Cd(OH){sub 2} nanowalls were directly grown on glass substrate by hydrothermal method. • The thicknesses of Cd(OH){sub 2} nanowalls can be effectively controlled by HMTA. • Cd(OH){sub 2} and CdO nanoporous walls exhibit very strong and broad emission properties. • Cd(OH){sub 2} and CdO nanoporous walls have exhibited very effective photocatalysts. • The two mixture nanoporous walls are beneficial for optoelectronic applications. - Abstract: Cadmium hydroxide nanowalls were directly grown on glass substrate by a hydrothermal method. The concentration of hexamethylenetetramine plays a crucial role for controlling the thicknesses of cadmium hydroxide nanowalls. A part of the cadmium hydroxide nanowalls can be converted to cadmium oxide nanoporous walls by annealing cadmium hydroxide in air at 350 °C for 1 h. Cadmium hydroxide and oxide nanoporous walls exhibited very strong and broad emission properties in the cathodoluminescence spectrum. Furthermore, cadmium hydroxide and oxide nanoporous walls can also provide a higher surface-to-volume ratio to result their higher photocatalytic performance in degradation of methylene blue.

  5. Process optimization of reaction of acid leaching residue of asbestos tailing and sodium hydroxide aqueous solution

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Silica is the major component of the acid leaching residue of asbestos tailing. The waterglass solution can be prepared by the reaction of the residue with sodium hydroxide aqueous solution. Compared to the high temperature reaction method, this process is environmental friendly and low cost. In this paper, the reaction process of the residue and the sodium hydroxide aqueous solution is optimized. The optimum reaction process parameters are as follows: the usage of sodium hydroxide is 26.4 g/100 g acid leaching residue, the reaction temperature is 90℃, the reaction time is 1 h, and the ratio of the liquid/solid is 2.0. The significance sequence of the process parameters to the alkali leaching reaction effect is the usage of sodium hydroxide > the ratio of the liquid/solid > the reaction time > the reaction temperature. The significance sequence to the leaching ratio of SiO2 is the ratio of the liquid/solid > the usage of sodium hydroxide > the reaction time > the reaction temperature. The significance sequence to the modulus of the sodium silicate is the ratio of the liquid/solid > the usage of sodium hydroxide > the reaction time > the reaction temperature. Under the optimum conditions, the leaching ratio of the SiO2 is 77.5%, and the modulus of the sodium silicate is 3.15. The XRD analysis result indicates that the major components of the alkali leaching residue are serpentine, talc, quartz and some albite.

  6. Evolution of the Calcium Paradigm: The Relation between Vitamin D, Serum Calcium and Calcium Absorption

    Directory of Open Access Journals (Sweden)

    Borje E. Christopher Nordin

    2010-09-01

    Full Text Available Osteoporosis is the index disease for calcium deficiency, just as rickets/osteomalacia is the index disease for vitamin D deficiency, but there is considerable overlap between them. The common explanation for this overlap is that hypovitaminosis D causes malabsorption of calcium which then causes secondary hyperparathyroidism and is effectively the same thing as calcium deficiency. This paradigm is incorrect. Hypovitaminosis D causes secondary hyperparathyroidism at serum calcidiol levels lower than 60 nmol/L long before it causes malabsorption of calcium because serum calcitriol (which controls calcium absorption is maintained until serum calcidiol falls below 20 nmol/L. This secondary hyperparathyroidism, probably due to loss of a “calcaemic” action of vitamin D on bone first described in 1957, destroys bone and explains why vitamin D insufficiency is a risk factor for osteoporosis. Vitamin D thus plays a central role in the maintenance of the serum (ionised calcium, which is more important to the organism than the preservation of the skeleton. Bone is sacrificed when absorbed dietary calcium does not match excretion through the skin, kidneys and bowel which is why calcium deficiency causes osteoporosis in experimental animals and, by implication, in humans.

  7. Limestone reaction in calcium aluminate cement–calcium sulfate systems

    Energy Technology Data Exchange (ETDEWEB)

    Bizzozero, Julien, E-mail: julien.bizzozero@gmail.com; Scrivener, Karen L.

    2015-10-15

    This paper reports a study of ternary blends composed of calcium aluminate cement, calcium sulfate hemihydrate and limestone. Compressive strength tests and hydration kinetics were studied as a function of limestone and calcium sulfate content. The phase evolution and the total porosity were followed and compared to thermodynamic simulation to understand the reactions involved and the effect of limestone on these binders. The reaction of limestone leads to the formation of hemicarboaluminate and monocarboaluminate. Increasing the ratio between sulfate and aluminate decreases the extent of limestone reaction.

  8. Synthesis of pure zeolite P2 from calcium silicate hydrate; tobermorite

    Directory of Open Access Journals (Sweden)

    Nasser Y. Mostafa

    2015-06-01

    Full Text Available Calcium silicate hydrate phases offer the possibility to become potential zeolites precursors due to its high silica contents. Pure calcium silicate hydrate phase; tobermorite (Ca5Si6O16(OH2·4H2O, was prepared by hydrothermal method at 175°C. Tobermorite was sucssefully converted to Zeolite P2 for the first time via refluxing in 3 M NaOH solution and in the presence of Al source. Sodium hydroxide removed calcium ions from the interlayers of calcium silicate phase and form mesoporous zeolite. The pure zeolite was obtained after extraction of Ca(OH2 with sugar solution. The zeolite products were characterized by using X-ray diffraction spectroscopy (XRD and Scanning Electron Microscopy (SEM with microanalysis (EDX. The Si/Al molar ratio of zeolite P can be controlled by vering the initinal Si/Al molar ratio. The cation-exchange capacity (CEC of the produced zeolite P was higher than those produced from fly ash.

  9. The Influence of Calcium Chloride Salt Solution on the Transport Properties of Cementitious Materials

    Directory of Open Access Journals (Sweden)

    Yaghoob Farnam

    2015-01-01

    Full Text Available The chemical interaction between calcium chloride (CaCl2 and cementitious binder may alter the transport properties of concrete which are important in predicting the service life of infrastructure elements. This paper presents a series of fluid and gas transport measurements made on cementitious mortars before and after exposure to various solutions with concentrations ranging from 0% to 29.8% CaCl2 by mass. Fluid absorption, oxygen diffusivity, and oxygen permeability were measured on mortar samples prepared using Type I and Type V cements. Three primary factors influence the transport properties of mortar exposed to CaCl2: (1 changes in the degree of saturation, (2 calcium hydroxide leaching, and (3 formation of chemical reaction products (i.e., Friedel’s salt, Kuzel’s salt, and calcium oxychloride. It is shown that an increase in the degree of saturation decreases oxygen permeability. At lower concentrations (~12%, the formation of chemical reaction products (mainly calcium oxychloride is a dominant factor decreasing the fluid and gas transport in concrete.

  10. Characterization of calcium containing plasma electrolytic oxidation coatings on AM50 magnesium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Srinivasan, P. Bala, E-mail: bala.srinivasan@gkss.de [Institute of Materials Research, GKSS-Forschungszentrum Geesthacht GmbH, D-21502 Geesthacht (Germany); Liang, J.; Blawert, C.; Stoermer, M.; Dietzel, W. [Institute of Materials Research, GKSS-Forschungszentrum Geesthacht GmbH, D-21502 Geesthacht (Germany)

    2010-04-01

    An attempt was made to produce calcium containing plasma electrolytic oxidation (PEO) coatings on AM50 magnesium alloy using an alkaline electrolyte. This study was performed in three alkaline electrolytes containing calcium hydroxide and sodium phosphate with three different mass ratios viz., 1:2.5, 1:5 and 1:7.5. All the three coatings produced were found to contain Ca and P in appreciable amounts. The concentration of P was found to be higher in the coatings obtained in the electrolytes with higher concentration of phosphate ions. Even though all the three coatings were found to be constituted with magnesium oxide and magnesium phosphate phases, X-ray diffraction analyses revealed that the phase composition was influenced by the phosphate ion concentration/conductivity of the electrolyte. Further, the PEO coating obtained in the 1:7.5 ratio electrolyte was found to contain di-calcium phosphate (monetite) and calcium peroxide phases, which were absent in the other two coatings. Potentiodynamic polarization studies performed in 0.1 M NaCl solution showed that the coatings obtained from the 1:5 ratio electrolyte possessed a superior corrosion resistance, which is attributed to the combined effect of thickness, compactness and phase/chemical composition of this coating.

  11. Development of polymer nanocomposites based on layered double hydroxides

    Directory of Open Access Journals (Sweden)

    Sipusic, J.

    2009-05-01

    Full Text Available Polymeric nanocomposites are commonly considered as systems composed of a polymeric matrix and - usually inorganic - filler. The types of nanofillers are indicated in Fig. 1. Beside wellknown layered silicate fillers, recent attention is attracted to layered double hydroxide fillers (LDH, mainly of synthetic origin. The structure of LDH is based on brucite, or magnesium hydroxide, Mg(OH2 and is illustrated in Fig. 2. The modification of LDHs is commonly done by organic anions, to increase the original interlayer distance and to improve the organophilicity of the filler, keeping in mind their final application as fillers for, usually hydrophobic, polymer matrices. We have used the modified rehydration procedure for preparing organically modified LDH. The stoichiometric quantities of Ca33Al2O6, CaO and benzoic (B (or undecenoic (U acid were mixed with water and some acetone. After long and vigorous shaking, the precipitated fillers were washed, dried and characterized. X-ray diffraction method (XRD has shown the increase of the original interlayer distance for unmodified LDH (OH–-saturated of 0.76 nm to the 1.6 nm in LDH-B or LDH-U fillers (Fig. 3. Infrared spectroscopy method (FTIR has confirmed the incorporation of benzoic anion within the filler layers (Fig. 4. For the preparation of LDH-B and LDH-U composites with polystyrene (PS, poly(methyl methacrylate (PMMA and copolymer (SMMA matrices, a two-step in situ bulk radical polymerization was selected (Table 1 for recipes, azobisisobutyronitrile as initiator, using conventional stirred tank reactor in the first step, and heated mold with the movable wall (Fig. 6 in the second step of polymerization. All the prepared composites with LDH-U fillers were macroscopically phase-separated, as was the PMMA/LDH-B composite.PS/LDH-B and SMMA/LDH-B samples were found to be transparent and were further examined for deduction of their structure (Fig. 5 and thermal properties. FTIR measurements showed that

  12. Form and stability of aluminum hydroxide complexes in dilute solution

    Science.gov (United States)

    Hem, John David; Roberson, Charles Elmer

    1967-01-01

    Laboratory studies of solutions 4.53 x 10 -4 to 4.5 x 10 -5 molal (12.2-1.2 ppm) in aluminum, in 0.01 molal sodium perchlorate, were conducted to obtain information as to the probable behavior of aluminum in natural water. When the solutions were brought to pH 7.5-9.5 and allowed to stand for 24 hours, a precipitate was obtained which was virtually amorphous as shown by X-rays, and which had a solubility equivalent to that of boehmite. This precipitate had a hydrolysis constant (*Ks4) of 1.93 x 10 -13a. When solutions were allowed to stead at this pH range for 10 days, their precipitates gave the X-ray pattern of bayerite (*Ks4 = 1.11 > (10- 4). These hydrolysis constants were obtained at 25?C. and corrected to zero ionic strength and are in close agreement with other published values. The predominant dissolved form in this pH range is Al(OH) -4. Below neutral pH (7.0) the dissolved aluminum species consist of octahedral units in which each aluminum ion is surrounded by six water molecules or hydroxide ions. Single units such as Al(OH2)6 + 3 and AlOH(OH2)5+2 are most abundant below pH 5.0, and where the molar ratio (r) of combined hydroxide to total dissolved aluminum is low. When r is greater than 1.0, polymerization of the octahedral units occurs. When r is between 2.0 and 3.0, solutions aged for 10 days or more contained colloidal particles between 0.10 and 0.45 ? in diameter. Particles whose diameters were greater than 0.10 ? were identified by X-ray diffraction as gibbsite. Particles smaller than 0.10 ? were also present and were shown by means of the electron microscope to have a hexagonal crystal pattern. Structured material consisting of sheets of coalesced six-membered rings of aluminum ions held together by double OH bridges has a distinctive kinetic behavior. This property was used to determine amounts of polymerized material in solutions having r between 1.0 and 3.0 after aging times ranging from a few hours to more than 4 months. Aging increased the

  13. Calcium binding protein-mediated regulation of voltage-gated calcium channels linked to human diseases

    Institute of Scientific and Technical Information of China (English)

    Nasrin NFJATBAKHSH; Zhong-ping FENG

    2011-01-01

    Calcium ion entry through voltage-gated calcium channels is essential for cellular signalling in a wide variety of cells and multiple physiological processes. Perturbations of voltage-gated calcium channel function can lead to pathophysiological consequences. Calcium binding proteins serve as calcium sensors and regulate the calcium channel properties via feedback mechanisms. This review highlights the current evidences of calcium binding protein-mediated channel regulation in human diseases.

  14. Preferential Intercalation of Pyridinedicarboxylates into Layered Double Hydroxides

    Institute of Scientific and Technical Information of China (English)

    李蕾; 莫丹; 陈大舟

    2005-01-01

    Intercalation of 2,3-,2,4-,2,5-,2,6-,3,4-,or3,5-pyridincdicarboxylate into the layered double hydroxide (LDH),[Mg0.73AIo.27(OH)2](CO3)0.14*1.34H2O was carried out by the reconstruction method in the molar ratio of organic acid: calcined LDH=3:8, in 80% alcoholic aqueous solution at 70℃. Selective reaction was observed in com-petitive experiments involving an equal concentration pairs of acids. The preference order of the organic acids intercalated into the Mg-Al-LDH was found to be in the order of 2,3-pyridinedicarboxylate>2,5-pyridinedicarboxylate>2,4-pyridinedicarboxylate>3,5-pyridinedicarboxylate>3,4-pyridinedicarboxylate>2,6-pyridinedic arboxylate. The structures of the intercalates formed by the reaction of six guests with Mg-Al-LDH were characterized by X-ray diffraction, infrared and thermogravimetry techniques. And the charge density on the oxygens of each of the carboxylate groups for the six anions was investigated utilizing ab initio (HF/6-31G) method by G98w. From the X-ray diffraction data, the guest size and the charge density of the oxygens of the guest, the orientation of 2,3-,2,4-,2,5-,2,6-,3,4-, or 3,5-pyridinedicarboxylate anions between the layers was determined and the preferential intercalation mechanism was discussed. These results indicate the possibility of a molecular recognition ability of LDH and it would be exploited for the chemical separation of some anions from solution.

  15. Physical properties of fixed-charge layer double hydroxides

    Science.gov (United States)

    Hines, D. R.; Solin, S. A.; Costantino, Umberto; Nocchetti, Morena

    2000-05-01

    The physical properties of a series of layer double hydroxides (LDH) of the form [(CO3)0.195(1-x)Cl0.39x(H2O)y]:[Zn0.61Al0.39(OH)2], 0layer water molecules form a hydration ring which defines the height of the solvated, nested Cl anion. The water molecules can tilt around their C2v axis such that the height of the solvated Cl ion is a function of the number of molecules forming the hydration ring. The composition dependence of the basal spacing, determined from x-ray-diffraction powder patterns measured as a function of humidity and temperature for these materials, is a function of both the Cl concentration (x) and the number of guest layer water molecules (y). Distinct basal spacing curves are observed for fully hydrated, partially hydrated, and dehydrated materials. At x=1 the Cl end-member material exhibits a change in stacking sequence from a 3R polytype to a 2H polytype upon dehydration. The dehydrated form of this material also exhibits a (3×3)R30° superlattice ordering of the Cl ions. Due to the nesting of the Cl ion and the active nature of the water molecules, the basal spacing vs x curve for the dehydrated materials is the only curve that can be fit by the discrete finite layer rigidity model. The interlayer rigidity parameter for LDH materials has been determined to be p=4.84+/-0.06 indicating that these materials are stiffer than class-II layered solids but not as stiff as class-III layered solids.

  16. Effective Construction of High-quality Iron Oxy-hydroxides and Co-doped Iron Oxy-hydroxides Nanostructures: Towards the Promising Oxygen Evolution Reaction Application

    Science.gov (United States)

    Zhang, Xinyu; An, Li; Yin, Jie; Xi, Pinxian; Zheng, Zhiping; Du, Yaping

    2017-01-01

    Rational design of high efficient and low cost electrocatalysts for oxygen evolution reaction (OER) plays an important role in water splitting. Herein, a general gelatin-assisted wet chemistry method is employed to fabricate well-defined iron oxy-hydroxides and transitional metal doped iron oxy-hydroxides nanomaterials, which show good catalytic performances for OER. Specifically, the Co-doped iron oxy-hydroxides (Co0.54Fe0.46OOH) show the excellent electrocatalytic performance for OER with an onset potential of 1.52 V, tafel slope of 47 mV/dec and outstanding stability. The ultrahigh oxygen evolution activity and strong durability, with superior performance in comparison to the pure iron oxy-hydroxide (FeOOH) catalysts, originate from the branch structure of Co0.54Fe0.46OOH on its surface so as to provide many active edge sites, enhanced mass/charge transport capability, easy release oxygen gas bubbles, and strong structural stability, which are advantageous for OER. Meanwhile, Co-doping in FeOOH nanostructures constitutes a desirable four-electron pathway for reversible oxygen evolution and reduction, which is potentially useful for rechargeable metal−air batteries, regenerative fuel cells, and other important clean energy devices. This work may provide a new insight into constructing the promising water oxidation catalysts for practical clean energy application. PMID:28272443

  17. Effective Construction of High-quality Iron Oxy-hydroxides and Co-doped Iron Oxy-hydroxides Nanostructures: Towards the Promising Oxygen Evolution Reaction Application.

    Science.gov (United States)

    Zhang, Xinyu; An, Li; Yin, Jie; Xi, Pinxian; Zheng, Zhiping; Du, Yaping

    2017-03-08

    Rational design of high efficient and low cost electrocatalysts for oxygen evolution reaction (OER) plays an important role in water splitting. Herein, a general gelatin-assisted wet chemistry method is employed to fabricate well-defined iron oxy-hydroxides and transitional metal doped iron oxy-hydroxides nanomaterials, which show good catalytic performances for OER. Specifically, the Co-doped iron oxy-hydroxides (Co0.54Fe0.46OOH) show the excellent electrocatalytic performance for OER with an onset potential of 1.52 V, tafel slope of 47 mV/dec and outstanding stability. The ultrahigh oxygen evolution activity and strong durability, with superior performance in comparison to the pure iron oxy-hydroxide (FeOOH) catalysts, originate from the branch structure of Co0.54Fe0.46OOH on its surface so as to provide many active edge sites, enhanced mass/charge transport capability, easy release oxygen gas bubbles, and strong structural stability, which are advantageous for OER. Meanwhile, Co-doping in FeOOH nanostructures constitutes a desirable four-electron pathway for reversible oxygen evolution and reduction, which is potentially useful for rechargeable metal-air batteries, regenerative fuel cells, and other important clean energy devices. This work may provide a new insight into constructing the promising water oxidation catalysts for practical clean energy application.

  18. Arsenic adsorption by iron-aluminium hydroxide coated onto macroporous supports: Insights from X-ray absorption spectroscopy and comparison with granular ferric hydroxides.

    Science.gov (United States)

    Suresh Kumar, Prashanth; Flores, Roxana Quiroga; Sjöstedt, Carin; Önnby, Linda

    2016-01-25

    This paper evaluates the arsenic adsorption characteristics of a macroporous polymer coated with coprecipitated iron-aluminium hydroxides (MHCMP). The MHCMP adsorbent-composite fits best with a pseudo-second order model for As(III) and a pseudo-first order kinetic model for As(V). The MHCMP shows a maximum adsorption capacity of 82.3 and 49.6 mg As/g adsorbent for As(III) and As(V) ions respectively, and adsorption followed the Langmuir model. Extended X-ray absorption fine structure showed that binding of As(III) ions were confirmed to take place on the iron hydroxides coated on the MHCMP, whereas for As(V) ions the binding specificity could not be attributed to one particular metal hydroxide. As(III) formed a bidentate mononuclear complex with Fe sites, whereas As(V) indicated on a bidentate binuclear complex with Al sites or monodentate with Fe sites on the adsorbent. The column experiments were run in a well water spiked with a low concentration of As(III) (100 μg/L) and a commercially available adsorbent (GEH(®)102) based on granular iron-hydroxide was used for comparison. It was found that the MHCMP was able to treat 7 times more volume of well water as compared to GEH(®)102, maintaining the threshold concentration of less than 10 μg As/L, indicating that the MHCMP is a superior adsorbent.

  19. Calcium signals in olfactory neurons.

    Science.gov (United States)

    Tareilus, E; Noé, J; Breer, H

    1995-11-09

    Laser scanning confocal microscopy in combination with the fluorescent calcium indicators Fluo-3 and Fura-Red was employed to estimate the intracellular concentration of free calcium ions in individual olfactory receptor neurons and to monitor temporal and spatial changes in the Ca(2+)-level upon stimulation. The chemosensory cells responded to odorants with a significant increase in the calcium concentration, preferentially in the dendritic knob. Applying various stimulation paradigma, it was found that in a population of isolated cells, subsets of receptor neurons display distinct patterns of responsiveness.

  20. Effect of Operating Parameters and Chemical Additives on Crystal Habit and Specific Cake Resistance of Zinc Hydroxide Precipitates

    Energy Technology Data Exchange (ETDEWEB)

    Alwin, Jennifer Louise [New Mexico State Univ., Las Cruces, NM (United States)

    1999-08-01

    The effect of process parameters and chemical additives on the specific cake resistance of zinc hydroxide precipitates was investigated. The ability of a slurry to be filtered is dependent upon the particle habit of the solid and the particle habit is influenced by certain process variables. The process variables studied include neutralization temperature, agitation type, and alkalinity source used for neutralization. Several commercially available chemical additives advertised to aid in solid/liquid separation were also examined in conjunction with hydroxide precipitation. A statistical analysis revealed that the neutralization temperature and the source of alkalinity were statistically significant in influencing the specific cake resistance of zinc hydroxide precipitates in this study. The type of agitation did not significantly effect the specific cake resistance of zinc hydroxide precipitates. The use of chemical additives in conjunction with hydroxide precipitation had a favorable effect on the filterability. The morphology of the hydroxide precipitates was analyzed using scanning electron microscopy.

  1. The Effect of Ultrafine Magnesium Hydroxide on the Tensile Properties and Flame Retardancy of Wood Plastic Composites

    Directory of Open Access Journals (Sweden)

    Zhiping Wu

    2014-01-01

    Full Text Available The effect of ultrafine magnesium hydroxide (UMH and ordinary magnesium hydroxide (OMH on the tensile properties and flame retardancy of wood plastic composites (WPC were investigated by tensile test, oxygen index tester, cone calorimeter test, and thermogravimetric analysis. The results showed that ultrafine magnesium hydroxide possesses strengthening and toughening effect of WPC. Scanning electron micrograph (SEM of fracture section of samples provided the positive evidence that the tensile properties of UMH/WPC are superior to that of WPC and OMH/WPC. The limited oxygen index (LOI and cone calorimeter test illustrated that ultrafine magnesium hydroxide has stronger flame retardancy and smoke suppression effect of WPC compared to that of ordinary magnesium hydroxide. The results of thermogravimetric analysis implied that ultrafine magnesium hydroxide can improve the char structure which plays an important role in reducing the degradation speed of the inner matrix during combustion process and increases the char residue at high temperature.

  2. 21 CFR 184.1187 - Calcium alginate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium alginate. 184.1187 Section 184.1187 Food... Specific Substances Affirmed as GRAS § 184.1187 Calcium alginate. (a) Calcium alginate (CAS Reg. No. 9005.... Calcium alginate is prepared by the neutralization of purified alginic acid with appropriate pH...

  3. Synthesis of Zn–Fe layered double hydroxides via an oxidation process and structural analysis of products

    Energy Technology Data Exchange (ETDEWEB)

    Morimoto, Kazuya, E-mail: kazuya.morimoto@aist.go.jp [Institute for Geo-Resources and Environment, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Higashi, Tsukuba, Ibaraki 305-8567 (Japan); Tamura, Kenji [Environmental Remediation Materials Unit, National Institute for Materials Science (NIMS), 1-1 Namiki, Tsukuba, Ibaraki 305-0044 (Japan); Anraku, Sohtaro [Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan); Sato, Tsutomu [Faculty of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan); Suzuki, Masaya [Institute for Geo-Resources and Environment, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Higashi, Tsukuba, Ibaraki 305-8567 (Japan); Yamada, Hirohisa [Environmental Remediation Materials Unit, National Institute for Materials Science (NIMS), 1-1 Namiki, Tsukuba, Ibaraki 305-0044 (Japan)

    2015-08-15

    The synthesis of Zn–Fe(III) layered double hydroxides was attempted, employing different pathways using either Fe(II) or Fe(III) species together with Zn as the initial reagents. The product derived from the synthesis employing Fe(II) was found to transition to a Zn–Fe(III) layered double hydroxides phase following oxidation process. In contrast, the product obtained with Fe(III) did not contain a layered double hydroxides phase, but rather consisted of simonkolleite and hydrous ferric oxide. It was determined that the valency of the Fe reagent used in the initial synthesis affected the generation of the layered double hydroxides phase. Fe(II) species have ionic radii and electronegativities similar to those of Zn, and therefore are more likely to form trioctahedral hydroxide layers with Zn species. - Graphical abstract: The synthesis of Zn–Fe(III) layered double hydroxides was attempted, employing different pathways using either Fe(II) or Fe(III) species together with Zn as the initial reagents. - Highlights: • Iron valency affected the generation of Zn–Fe layered double hydroxides. • Zn–Fe layered double hydroxides were successfully synthesized using Fe(II). • Fe(II) species were likely to form trioctahedral hydroxide layers with Zn species.

  4. Calcium Orthophosphate Cements and Concretes

    Directory of Open Access Journals (Sweden)

    Sergey V. Dorozhkin

    2009-03-01

    Full Text Available In early 1980s, researchers discovered self-setting calcium orthophosphate cements, which are a bioactive and biodegradable grafting material in the form of a powder and a liquid. Both phases form after mixing a viscous paste that after being implanted, sets and hardens within the body as either a non-stoichiometric calcium deficient hydroxyapatite (CDHA or brushite, sometimes blended with unreacted particles and other phases. As both CDHA and brushite are remarkably biocompartible and bioresorbable (therefore, in vivo they can be replaced with newly forming bone, calcium orthophosphate cements represent a good correction technique for non-weight-bearing bone fractures or defects and appear to be very promising materials for bone grafting applications. Besides, these cements possess an excellent osteoconductivity, molding capabilities and easy manipulation. Furthermore, reinforced cement formulations are available, which in a certain sense might be described as calcium orthophosphate concretes. The concepts established by calcium orthophosphate cement pioneers in the early 1980s were used as a platform to initiate a new generation of bone substitute materials for commercialization. Since then, advances have been made in the composition, performance and manufacturing; several beneficial formulations have already been introduced as a result. Many other compositions are in experimental stages. In this review, an insight into calcium orthophosphate cements and concretes, as excellent biomaterials suitable for both dental and bone grafting application, has been provided.

  5. Mixing Acid Salts and Layered Double Hydroxides in Nanoscale under Solid Condition

    Directory of Open Access Journals (Sweden)

    Hirokazu Nakayama

    2014-07-01

    Full Text Available The immobilization of potassium sorbate, potassium aspartate and sorbic acid in layered double hydroxide under solid condition was examined. By simply mixing two solids, immobilization of sorbate and aspartate in the interlayer space of nitrate-type layered double hydroxide, so called intercalation reaction, was achieved, and the uptakes, that is, the amount of immobilized salts and the interlayer distances of intercalation compounds were almost the same as those obtained in aqueous solution. However, no intercalation was achieved for sorbic acid. Although intercalation of sorbate and aspartate into chloride-type layered double hydroxide was possible, the uptakes for these intercalation compounds were lower than those obtained using nitrate-type layered double hydroxide. The intercalation under solid condition could be achieved to the same extent as for ion-exchange reaction in aqueous solution, and the reactivity was similar to that observed in aqueous solution. This method will enable the encapsulation of acidic drug in layered double hydroxide as nano level simply by mixing both solids.

  6. Vibrational dynamics of aqueous hydroxide solutions probed using broadband 2DIR spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Mandal, Aritra [Department of Chemistry, James Franck Institute, and Institute for Biophysical Dynamics, University of Chicago, Chicago, Illinois 60637 (United States); Department of Chemistry, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Tokmakoff, Andrei, E-mail: tokmakoff@uchicago.edu [Department of Chemistry, James Franck Institute, and Institute for Biophysical Dynamics, University of Chicago, Chicago, Illinois 60637 (United States)

    2015-11-21

    We employed ultrafast transient absorption and broadband 2DIR spectroscopy to study the vibrational dynamics of aqueous hydroxide solutions by exciting the O–H stretch vibrations of the strongly hydrogen-bonded hydroxide solvation shell water and probing the continuum absorption of the solvated ion between 1500 and 3800 cm{sup −1}. We observe rapid vibrational relaxation processes on 150–250 fs time scales across the entire probed spectral region as well as slower vibrational dynamics on 1–2 ps time scales. Furthermore, the O–H stretch excitation loses its frequency memory in 180 fs, and vibrational energy exchange between bulk-like water vibrations and hydroxide-associated water vibrations occurs in ∼200 fs. The fast dynamics in this system originate in strong nonlinear coupling between intra- and intermolecular vibrations and are explained in terms of non-adiabatic vibrational relaxation. These measurements indicate that the vibrational dynamics of the aqueous hydroxide complex are faster than the time scales reported for long-range transport of protons in aqueous hydroxide solutions.

  7. Zimmer slipstream magnesium hydroxide recovery demonstration. Volume II of II. Appendices

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Dravo Lime has for many years supplied magnesium containing lime in the ranges of 3-6% MgO. Several years ago Dravo Lime realized the potential operating savings its FGD customers could benefit from if magnesium could be recovered from FGD waste streams. As a result, several different proprietary processes have been developed for the recovery of magnesium hydroxide. These recovery processes include steps for magnesium hydroxide separation, purification, and crystal growth. The process implemented at The Cincinnati Gas Electric Company`s Wm. H. Zimmer Station was piloted by Dravo Lime Company at Allegheny Power System`s Mitchell Station near Monongahela, PA during the fourth quarter in 1989 and first quarter in 1990. This pilot work was the foundation for further development of the ThioClear process at Dravo`s pilot plant at CG&E Miami Fort Station. The ThioClear process is a closed loop version of the magnesium hydroxide recovery process with the same unit operations and products but also including an absorber tower for scrubbing flue gas. Testing at Miami Fort of the ThioClear process led to improvements in separation of magnesium hydroxide from gypsum that are part of the magnesium hydroxide recovery process installed at Zimmer Station. This document contains the Appendices for this report.

  8. INFLUENCE OF HEAVY METALS HYDROXIDES ON WATER DISSOCIATION IN BIPOLAR MEMBRANE

    Directory of Open Access Journals (Sweden)

    Sheldeshov N. V.

    2015-12-01

    Full Text Available The results of study of bipolar membrane – analogue of MB-2, modified with chemically introduced chromium (III, iron (III and nickel (II hydroxides by the method of frequency spectrum of electrochemical impedance, by infrared spectroscopy and scanning electron microscopy in combination with X-ray spectrum analysis are presented. It is shown, that sequential treatment of cation-exchanger, contained in cationexchange membrane, with metal salt solution and alkali solution does not result in formation of complex compounds of these metals with ionic groups of ion exchanger. It was found that in these conditions the presence of heavy metals in the phase of cationexchanger confirmed by X-ray analysis, however, crystals of hydroxides of heavy metals are not detected in the size range of 1000 nm to 20 nm. These heavy metal compounds are thermally unstable and their catalytic activity in the reaction of dissociation of water molecules decreases with increasing temperature during heat treatment. The introduction of low-soluble hydroxides of d-metals (chromium (III, iron (III, nickel(II by chemical method can significantly improve the electrochemical characteristics of a bipolar membrane. The most effective catalysts in water dissociation reaction are the hydroxides of chromium (III and iron (III and, as a consequence, membranes with these hydroxides have a lower value of overpotential compared with original membrane at the same current density

  9. Factors affecting calcium balance in Chinese adolescents.

    Science.gov (United States)

    Yin, Jing; Zhang, Qian; Liu, Ailing; Du, Weijing; Wang, Xiaoyan; Hu, Xiaoqi; Ma, Guansheng

    2010-01-01

    Chinese dietary reference intakes (DRIs) for calcium were developed mainly from studies conducted amongst Caucasians, yet a recent review showed that reference calcium intakes for Asians are likely to be different from those of Caucasians (Lee and Jiang, 2008). In order to develop calcium DRIs for Chinese adolescents, it is necessary to explore the characteristics and potential influencing factors of calcium metabolic balance in Chinese adolescents. A total of 80 students (15.1+/-0.8 years) were recruited stratified by gender from a 1-year calcium supplementation study. Subjects were randomly designed to four groups and supplemented with calcium carbonate tablets providing elemental calcium at 63, 354, 660, and 966 mg/day, respectively. Subjects consumed food from a 3-day cycle menu prepared by staff for 10 days. Elemental calcium in samples of foods, feces, and urine was determined in duplicates by inductively coupled plasma atomic emission spectrometry. The total calcium intake ranged from 352 to 1323 mg/day. The calcium apparent absorption efficiency and retention in boys were significantly higher than that in girls (68.7% vs. 46.4%, 480 mg/day vs. 204 mg/day, PCalcium retention increased with calcium intakes, but did not reach a plateau. Calcium absorption efficiency in boys increased with calcium intake up to 665 mg/day, and decreased after that. In girls, calcium absorption efficiency decreased with calcium intake. Calcium absorption efficiency increased within 1 year after first spermatorrhea in boys, but decreased with pubertal development in girls. Sex, calcium intake, age, and pubertal development were the most important determinants of calcium absorption (R(2)=0.508, Pcalcium intake, age, and pubertal development are important factors for calcium retention and absorption during growth, which should be considered for the development of calcium DRIs for Chinese adolescents.

  10. A Comprehensive Study of Osteogenic Calcium Phosphate Silicate Cement: Material Characterization and In Vitro/In Vivo Testing.

    Science.gov (United States)

    Gong, Tianxing; Wang, Zhiqin; Zhang, Yixi; Zhang, Yubiao; Hou, Mingxiao; Liu, Xinwei; Wang, Yu; Zhao, Lejun; Ruse, N Dorin; Troczynski, Tom; Häfeli, Urs O

    2016-02-18

    Vertebral compression fractures can be successfully restored by injectable bone cements. Here the as-yet unexplored in vitro cytotoxicity, in vivo biodegradation, and osteoconductivity of a new calcium phosphate silicate cements (CPSC) are studied, where monocalcium phosphate (MCP; 5, 10, and 15 wt%) is added to calcium silicate cement (CSC). Setting rate and compressive strength of CPSC decrease with the addition of MCP. The crystallinity, microstructure, and porosity of hardened CPSC are evaluated by X-ray diffractometer, Fourier transform infrared spectroscopy, and microcomputed tomography (CT). It is found that MCP reacts with calcium hydroxide, one of CSC hydration products, to precipitate apatite. While the reaction accelerates the hydration of CSC, the formation of calcium silicate hydrate gel is disturbed and highly porous microstructures form, resulting in weaker compressive strength. In vitro studies demonstrate that CPSC is noncytotoxic to osteoblast cells and promotes their proliferation. In the rabbit tibia implantation model, clinical X-ray and CT scans demonstrate that CPSC biodegrades slower and osseointegrates better than clinically used calcium phosphate cement (CPC). Histological studies demonstrate that CPSC is osteoconductive and induces higher bone formation than CPC, a finding that might warrant future clinical studies.

  11. Effects of Leaching Behavior of Calcium Ions on Compression and Durability of Cement-based Materials with Mineral Admixtures

    Directory of Open Access Journals (Sweden)

    Wei-Ting Lin

    2013-05-01

    Full Text Available Leaching of calcium ions increases the porosity of cement-based materials, consequently resulting in a negative effect on durability since it provides an entry for aggressive harmful ions, causing reinforcing steel corrosion. This study investigates the effects of leaching behavior of calcium ions on the compression and durability of cement-based materials. Since the parameters influencing the leaching behavior of cement-based materials are unclear and diverse, this paper focuses on the influence of added mineral admixtures (fly ash, slag and silica fume on the leaching behavior of calcium ions regarding compression and durability of cemented-based materials. Ammonium nitrate solution was used to accelerate the leaching process in this study. Scanning electron microscopy, X-ray diffraction analysis, and thermogravimetric analysis were employed to analyze and compare the cement-based material compositions prior to and after calcium ion leaching. The experimental results show that the mineral admixtures reduce calcium hydroxide quantity and refine pore structure through pozzolanic reaction, thus enhancing the compressive strength and durability of cement-based materials.

  12. Preparation And Characterization Of Modified Calcium Oxide From Natural Sources And Their Application In The Transesterification Of Palm Oil

    Directory of Open Access Journals (Sweden)

    Aqliliriana

    2015-08-01

    Full Text Available Abstract Calcium oxide catalysts were prepared from natural calcium sources such as limestone and mud creeper shell and the catalytic activities were evaluated in the transesterification of palm oil. The raw material which mainly composed of calcium carbonate can be easily converted to calcium oxide CaO after calcination above 1000 K for few hours. Abundant cheap sources benign high conversion and nontoxic become main advantages of these catalysts. The catalysts were characterized by XRF TGA XRD CO2-TPD SEM and BET methods. Thermal decomposition of CaCO3 will produced CaO which later will be converted into calcium hydroxide CaOH2 via simple hydration technique. Under optimum reaction condition methanol to oil ratio 151 catalyst loading 3 wt. reaction temperature 338 K for 5 hours the highest conversion of palm oil to methyl ester recorded were 98 and 94 when using modified limestone and mud creeper shell respectively. The results observed an increment up to 80 by using modified catalysts with characterization results showed high in basicity and surface area. Hence promising materials via simple and cheap method can be achieved.

  13. Study on Fixation of CO2 and Production of Precipitated Calcium Carbonate Using Steel Slag%利用钢渣固结CO2制备沉淀碳酸钙的试验研究

    Institute of Scientific and Technical Information of China (English)

    朱蓓蓉; 杨全兵

    2011-01-01

    The possibility of fixation of CO2 and production of precipitated calcium carbonate by carbonating acetate solution of calcium extracted from steel slag was investigated. The composition of precipitate produced after carbonation was then analyzed with XRD and TG-DTA. The results show that calcium acetate must be converted into calcium hydroxide by adding sodium hydroxide into calcium acetate solution and then precipitated calcium carbonate can be produced by carbonating the solution. Acetate solution of calcium extracted from steel slag can be carbonated by adding enough sodium hydroxide but the purity of precipitated calcium carbonate produced is only about 60% and the conversion of calcium is only about 35. 00%. To improve the effect of carbonation and to produce precipitated calcium carbonate with a high purity, other ions dissolved in steel slag should be removed from acetate solution of calcium extracted from steel slag.%研究了基于醋酸提取钢渣中钙离子所获得的醋酸钙溶液碳化固结CO2并制备沉淀碳酸钙的可行性,借助于XRD,TG-DTA对碳化后生成的沉淀物进行了成分分析和综合热分析.结果表明:醋酸钙溶液需掺入氢氧化钠,将其中的醋酸钙转化成氢氧化钙,方可碳化生成沉淀碳酸钙;在由醋酸提取钢渣中钙离子所获得的醋酸钙溶液中掺入足量氢氧化钠,可使其中的钙离子碳化生成沉淀碳酸钙,但该碳酸钙的纯度(质量分数)仅为60%左右,钙离子转化率(质量分数)仅为35.00%左右,如果将该溶液进行分离处理,除去其中其他离子的干扰,则可高效碳化成高纯度沉淀碳酸钙.

  14. Mitochondrial calcium uptake.

    Science.gov (United States)

    Williams, George S B; Boyman, Liron; Chikando, Aristide C; Khairallah, Ramzi J; Lederer, W J

    2013-06-25

    Calcium (Ca(2+)) uptake into the mitochondrial matrix is critically important to cellular function. As a regulator of matrix Ca(2+) levels, this flux influences energy production and can initiate cell death. If large, this flux could potentially alter intracellular Ca(2+) ([Ca(2+)]i) signals. Despite years of study, fundamental disagreements on the extent and speed of mitochondrial Ca(2+) uptake still exist. Here, we review and quantitatively analyze mitochondrial Ca(2+) uptake fluxes from different tissues and interpret the results with respect to the recently proposed mitochondrial Ca(2+) uniporter (MCU) candidate. This quantitative analysis yields four clear results: (i) under physiological conditions, Ca(2+) influx into the mitochondria via the MCU is small relative to other cytosolic Ca(2+) extrusion pathways; (ii) single MCU conductance is ∼6-7 pS (105 mM [Ca(2+)]), and MCU flux appears to be modulated by [Ca(2+)]i, suggesting Ca(2+) regulation of MCU open probability (P(O)); (iii) in the heart, two features are clear: the number of MCU channels per mitochondrion can be calculated, and MCU probability is low under normal conditions; and (iv) in skeletal muscle and liver cells, uptake per mitochondrion varies in magnitude but total uptake per cell still appears to be modest. Based on our analysis of available quantitative data, we conclude that although Ca(2+) critically regulates mitochondrial function, the mitochondria do not act as a significant dynamic buffer of cytosolic Ca(2+) under physiological conditions. Nevertheless, with prolonged (superphysiological) elevations of [Ca(2+)]i, mitochondrial Ca(2+) uptake can increase 10- to 1,000-fold and begin to shape [Ca(2+)]i dynamics.

  15. Dopaminergic regulation of dendritic calcium: fast multisite calcium imaging.

    Science.gov (United States)

    Zhou, Wen-Liang; Oikonomou, Katerina D; Short, Shaina M; Antic, Srdjan D

    2013-01-01

    Optimal dopamine tone is required for the normal cortical function; however it is still unclear how cortical-dopamine-release affects information processing in individual cortical neurons. Thousands of glutamatergic inputs impinge onto elaborate dendritic trees of neocortical pyramidal neurons. In the process of ensuing synaptic integration (information processing), a variety of calcium transients are generated in remote dendritic compartments. In order to understand the cellular mechanisms of dopaminergic modulation it is important to know whether and how dopaminergic signals affect dendritic calcium transients. In this chapter, we describe a relatively inexpensive method for monitoring dendritic calcium fluctuations at multiple loci across the pyramidal dendritic tree, at the same moment of time (simultaneously). The experiments have been designed to measure the amplitude, time course and spatial extent of action potential-associated dendritic calcium transients before and after application of dopaminergic drugs. In the examples provided here the dendritic calcium transients were evoked by triggering the somatic action potentials (backpropagation-evoked), and puffs of exogenous dopamine were applied locally onto selected dendritic branches.

  16. Formation of calcium complexes by borogluconate in vitro and during calcium borogluconate infusion in sheep.

    Science.gov (United States)

    Farningham, D A

    1985-07-01

    The effect of borogluconate on plasma calcium fractions was studied in vitro and in vivo in sheep. In vitro calcium chloride was more effective in raising ionised plasma calcium than calcium borogluconate. Sodium borate or gluconate added to blood caused only small decreases in blood ionised calcium. However, together, a synergistic reduction in ionised calcium was observed. Following calcium borogluconate infusions into sheep, total plasma calcium rose primarily because of an increase in the unionised ultrafiltrable fraction. Other changes observed following the infusion were hypercalciuria, decreased glomerular filtration rate and acidosis. Sodium borogluconate administered subcutaneously lowered total plasma calcium. This probably resulted from enhanced calcium excretion. It is suggested that since the anionic component of calcium solutions alters the availability and retention of calcium, it is likely to affect clinical efficacy significantly.

  17. An empirical model to estimate density of sodium hydroxide solution: An activator of geopolymer concretes

    Science.gov (United States)

    Rajamane, N. P.; Nataraja, M. C.; Jeyalakshmi, R.; Nithiyanantham, S.

    2016-02-01

    Geopolymer concrete is zero-Portland cement concrete containing alumino-silicate based inorganic polymer as binder. The polymer is obtained by chemical activation of alumina and silica bearing materials, blast furnace slag by highly alkaline solutions such as hydroxide and silicates of alkali metals. Sodium hydroxide solutions of different concentrations are commonly used in making GPC mixes. Often, it is seen that sodium hydroxide solution of very high concentration is diluted with water to obtain SHS of desired concentration. While doing so it was observed that the solute particles of NaOH in SHS tend to occupy lower volumes as the degree of dilution increases. This aspect is discussed in this paper. The observed phenomenon needs to be understood while formulating the GPC mixes since this influences considerably the relationship between concentration and density of SHS. This paper suggests an empirical formula to relate density of SHS directly to concentration expressed by w/w.

  18. Nickel-vanadium monolayer double hydroxide for efficient electrochemical water oxidation

    Science.gov (United States)

    Fan, Ke; Chen, Hong; Ji, Yongfei; Huang, Hui; Claesson, Per Martin; Daniel, Quentin; Philippe, Bertrand; Rensmo, Håkan; Li, Fusheng; Luo, Yi; Sun, Licheng

    2016-06-01

    Highly active and low-cost electrocatalysts for water oxidation are required due to the demands on sustainable solar fuels; however, developing highly efficient catalysts to meet industrial requirements remains a challenge. Herein, we report a monolayer of nickel-vanadium-layered double hydroxide that shows a current density of 27 mA cm-2 (57 mA cm-2 after ohmic-drop correction) at an overpotential of 350 mV for water oxidation. Such performance is comparable to those of the best-performing nickel-iron-layered double hydroxides for water oxidation in alkaline media. Mechanistic studies indicate that the nickel-vanadium-layered double hydroxides can provide high intrinsic catalytic activity, mainly due to enhanced conductivity, facile electron transfer and abundant active sites. This work may expand the scope of cost-effective electrocatalysts for water splitting.

  19. Nickel–vanadium monolayer double hydroxide for efficient electrochemical water oxidation

    Science.gov (United States)

    Fan, Ke; Chen, Hong; Ji, Yongfei; Huang, Hui; Claesson, Per Martin; Daniel, Quentin; Philippe, Bertrand; Rensmo, Håkan; Li, Fusheng; Luo, Yi; Sun, Licheng

    2016-01-01

    Highly active and low-cost electrocatalysts for water oxidation are required due to the demands on sustainable solar fuels; however, developing highly efficient catalysts to meet industrial requirements remains a challenge. Herein, we report a monolayer of nickel–vanadium-layered double hydroxide that shows a current density of 27 mA cm−2 (57 mA cm−2 after ohmic-drop correction) at an overpotential of 350 mV for water oxidation. Such performance is comparable to those of the best-performing nickel–iron-layered double hydroxides for water oxidation in alkaline media. Mechanistic studies indicate that the nickel–vanadium-layered double hydroxides can provide high intrinsic catalytic activity, mainly due to enhanced conductivity, facile electron transfer and abundant active sites. This work may expand the scope of cost-effective electrocatalysts for water splitting. PMID:27306541

  20. The effect of crystal orientation on the cryogenic strength of hydroxide catalysis bonded sapphire

    Science.gov (United States)

    Haughian, K.; Douglas, R.; van Veggel, A. A.; Hough, J.; Khalaidovski, A.; Rowan, S.; Suzuki, T.; Yamamoto, K.

    2015-04-01

    Hydroxide catalysis bonding has been used in gravitational wave detectors to precisely and securely join components of quasi-monolithic silica suspensions. Plans to operate future detectors at cryogenic temperatures has created the need for a change in the test mass and suspension material. Mono-crystalline sapphire is one candidate material for use at cryogenic temperatures and is being investigated for use in the KAGRA detector. The crystalline structure of sapphire may influence the properties of the hydroxide catalysis bond formed. Here, results are presented of studies of the potential influence of the crystal orientation of sapphire on the shear strength of the hydroxide catalysis bonds formed between sapphire samples. The strength was tested at approximately 8 K; this is the first measurement of the strength of such bonds between sapphire at such reduced temperatures. Our results suggest that all orientation combinations investigated produce bonds of sufficient strength for use in typical mirror suspension designs, with average strengths >23 MPa.

  1. Electroosmotic dewatering of chalk sludge, iron hydroxide sludge, wet fly ash and biomass sludge

    DEFF Research Database (Denmark)

    Hansen, H.K.; Christensen, Iben Vernegren; Ottosen, Lisbeth M.;

    2003-01-01

    Electroosmotic dewatering has been tested in laboratory cells on four different porous materials: chalk sludge, iron hydroxide sludge, wet fly ash and biomass sludge from enzyme production. In all cases it was possible to remove water when passing electric DC current through the material. Casagra......Electroosmotic dewatering has been tested in laboratory cells on four different porous materials: chalk sludge, iron hydroxide sludge, wet fly ash and biomass sludge from enzyme production. In all cases it was possible to remove water when passing electric DC current through the material....... Casagrande's coefficients were determined for the four materials at different water contents. The experiments in this work showed that chalk could be dewatered from 40% to 79% DM (dry matter), fly ash from 75 to 82% DM, iron hydroxide sludge from 2.7 to 19% DM and biomass from 3 to 33% DM by electroosmosis...

  2. Large-scale Hydrothermal Synthesis and Characterization of Size-controlled Lanthanum Hydroxide Nanorods

    Institute of Scientific and Technical Information of China (English)

    YI,Ran; ZHANG,Ning; SHI,Rongrong; LI,Yongbo; QIU Guanzhou; LIU Xiaohe

    2009-01-01

    Uniform lanthanum hydroxide nanorods were successfully synthesized in large quantities through a facile hydrothermal synthetic method, in which soluble lanthanum nitrate was used to supply the lanthanum source and triethylamine (TEA) was used as both alkaline agent and complexing agent. The influences of triethylamine amount, surfactant, reaction temperature and time on the size and shape of lanthanum hydroxide nanorods were investigated in detail. Trivalent rare earth ion doped lanthanum hydroxide nanorods were also obtained in this paper. The phase structures and morphologies of the as-prepared products were investigated in detail by X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED) and high-resolution transmis-sion electron microscopy (HRTEM). The probable formation mechanism was proposed based on the experimental results.

  3. Removal of Indigo Carmine Dye from Aqueous Solution Using Magnesium Hydroxide as an Adsorbent

    Directory of Open Access Journals (Sweden)

    Thimmasandra Narayan Ramesh

    2015-01-01

    Full Text Available Magnesium hydroxide is used as an adsorbent for the removal of indigo carmine dye from aqueous solution. We have investigated the effectiveness of removal of indigo carmine dye from aqueous solutions at pH 6-7 and 12-13 using magnesium hydroxide thereby varying the dose of the adsorbent, concentration of the dye, duration, and temperature. Structural transformations of adsorbent during the adsorption process at different pH values are monitored using powder X-ray diffraction and infrared spectroscopy. Different types of adsorption isotherm models were evaluated and it was found that Langmuir isotherm fits well at both pH values (6-7 and 12-13. Adsorption of indigo carmine onto magnesium hydroxide at pH 6-7/pH 12-13 follows pseudo-second order rate kinetics.

  4. [Calcium metabolism characteristics in microgravity].

    Science.gov (United States)

    Grigor'ev, A I; Larina, I M; Morukov, B V

    1999-06-01

    The results of research of calcium exchange parameters at cosmonauts taken part in long space flights (SF) onboard of orbital stations "SALUT" and "MIR" within 1978-1998 were generalized. The analysis of data received during observation of 44 cosmonauts (18 of them have taken part in long SF twice) was done. The observation was carried out before and after SF by duration 30-438 days. The content of a total calcium in blood serum was increased basically by the increase of its ionized fraction after flights of moderate (3-6 months) and large duration (6-14 months) along with the significant increase of PTH and decrease of calcitonin levels. The content of osteocalcin after SF was increased. Three cosmonauts participated in research of calcium kinetics using stable isotopes before, in time and after a 115-day SF. Reduction of intestinal absorption, excretion through a gastrointestinal tract, and increase of calcium excretion with urine were marked in time of SF. In early postflight period a level of intestinal absorption, on the average, was much lower than in SF, and the calcium removal through intestine was increased. Both renal and intestinal excretion of calcium were not normalized in 3.5-4.5 months after end of SF. Increase of resorbtive processes in bone tissues which induced negative bone balance during flight was observed in all test subjects, proceeding from estimations of speed of the basic calcium flows made on the basis of mathematical modeling. The conclusion about decrease in speed of bone tissue remodeling and strengthening of its resorption proves to be true by data of research of biochemical and endocrine markers.

  5. Calcium wave of tubuloglomerular feedback.

    Science.gov (United States)

    Peti-Peterdi, János

    2006-08-01

    ATP release from macula densa (MD) cells into the interstitium of the juxtaglomerular (JG) apparatus (JGA) is an integral component of the tubuloglomerular feedback (TGF) mechanism that controls the glomerular filtration rate. Because the cells of the JGA express a number of calcium-coupled purinergic receptors, these studies tested the hypothesis that TGF activation triggers a calcium wave that spreads from the MD toward distant cells of the JGA and glomerulus. Ratiometric calcium imaging of in vitro microperfused isolated JGA-glomerulus complex dissected from rabbits was performed with fluo-4/fura red and confocal fluorescence microscopy. Activation of TGF by increasing tubular flow rate at the MD rapidly produced a significant elevation in intracellular Ca(2+) concentration ([Ca(2+)](i)) in extraglomerular mesangial cells (by 187.6 +/- 45.1 nM) and JG renin granular cells (by 281.4 +/- 66.6 nM). Subsequently, cell-to-cell propagation of the calcium signal at a rate of 12.6 +/- 1.1 microm/s was observed upstream toward proximal segments of the afferent arteriole and adjacent glomeruli, as well as toward intraglomerular elements including the most distant podocytes (5.9 +/- 0.4 microm/s). The same calcium wave was observed in nonperfusing glomeruli, causing vasoconstriction and contractions of the glomerular tuft. Gap junction uncoupling, an ATP scavenger enzyme cocktail, and pharmacological inhibition of P(2) purinergic receptors, but not adenosine A(1) receptor blockade, abolished the changes in [Ca(2+)](i) and propagation of the calcium wave. These studies provided evidence that both gap junctional communication and extracellular ATP are integral components of the TGF calcium wave.

  6. Aluminum phosphate shows more adjuvanticity than Aluminum hydroxide in recombinant hepatitis –B vaccine formulation

    Directory of Open Access Journals (Sweden)

    2008-08-01

    Full Text Available Background: Although a number of investigation have been carried out to find alternative adjuvants to aluminum salts in vaccine formulations, they are still extensively used due to their good track record of safety, low cost and proper adjuvanticity with a variety of antigens. Adsorption of antigens onto aluminum compounds depends heavily on electrostatic forces between adjuvant and antigen. Commercial recombinant protein hepatitis B vaccines containing aluminum hydroxide as adjuvant is facing low induction of immunity in some sections of the vaccinated population. To follow the current global efforts in finding more potent hepatitis B vaccine formulation, adjuvanticity of aluminum phosphate has been compared to aluminum hydroxide. Materials and methods: The adjuvant properties of aluminum hydroxide and aluminum phosphate in a vaccine formulation containing a locally manufactured hepatitis B (HBs surface antigen was evaluated in Balb/C mice. The formulations were administered intra peritoneally (i.p. and the titers of antibody which was induced after 28 days were determined using ELISA technique. The geometric mean of antibody titer (GMT, seroconversion and seroprotection rates, ED50 and relative potency of different formulations were determined. Results: All the adjuvanicity markers obtained in aluminum phosphate formulation were significantly higher than aluminum hydroxide. The geometric mean of antibody titer of aluminum phosphate was approximately three folds more than aluminum hydroxide. Conclusion: Aluminum phosphate showed more adjuvanticity than aluminum hydroxide in hepatitis B vaccine. Therefore the use of aluminum phosphate as adjuvant in this vaccine may lead to higher immunity with longer duration of effects in vaccinated groups.

  7. Process optimization of reaction of acid leaching residue of asbestos tailing and sodium hydroxide aqueous solution

    Institute of Scientific and Technical Information of China (English)

    DU GaoXiang; ZHENG ShuiLin; DING Hao

    2009-01-01

    Silica is the major component of the acid leaching residue of asbestos tailing. The waterglass solution can be prepared by the reaction of the residue with sodium hydroxide aqueous solution. Compared to the high temperature reaction method, this process is environmental friendly and low cost. In this paper, the reaction process of the residue and the sodium hydroxide aqueous solution is optimized. The op-timum reaction process parameters are as follows: the usage of sodium hydroxide is 26.4 g/100 g acid leaching residue, the reaction temperature is 90℃, the reaction time is 1 h, and the ratio of the liq-uid/solid is 2.0. The significance sequence of the process parameters to the alkali leaching reaction effect is the usage of sodium hydroxide > the ratio of the liquid/solid > the reaction time > the reaction temperature. The significance sequence to the leaching ratio of SiO2 is the ratio of the liquid/solid > the usage of sodium hydroxide > the reaction time > the reaction temperature. The significance sequence to the modulus of the sodium silicate is the ratio of the liquid/solid > the usage of sodium hydroxide > the reaction time > the reaction temperature. Under the optimum conditions, the leaching ratio of the SiO2 is 77.5%, and the modulus of the sodium silicate is 3.15. The XRD analysis result indicates that the major components of the alkali leaching residue are serpentine, talc, quartz and some albite.

  8. Preparation of hydroxide ion conductive KOH–layered double hydroxide electrolytes for an all-solid-state iron–air secondary battery

    Directory of Open Access Journals (Sweden)

    Taku Tsuneishi

    2014-06-01

    Full Text Available Anion conductive solid electrolytes based on Mg–Al layered double hydroxide (LDH were prepared for application in an all-solid-state Fe–air battery. The ionic conductivity and the conducting ion species were evaluated from impedance and electromotive force measurements. The ion conductivity of LDH was markedly enhanced upon addition of KOH. The electromotive force in a water vapor concentration cell was similar to that of an anion-conducting polymer membrane. The KOH–LDH obtained was used as a hydroxide ion conductive electrolyte for all-solid-state Fe–air batteries. The cell performance of the Fe–air batteries was examined using a mixture of KOH–LDH and iron-oxide-supported carbon as the negative electrode.

  9. Double-Shelled Nanocages with Cobalt Hydroxide Inner Shell and Layered Double Hydroxides Outer Shell as High-Efficiency Polysulfide Mediator for Lithium-Sulfur Batteries.

    Science.gov (United States)

    Zhang, Jintao; Hu, Han; Li, Zhen; Lou, Xiong Wen David

    2016-03-14

    Lithium-sulfur (Li-S) batteries have been considered as a promising candidate for next-generation electrochemical energy-storage technologies because of their overwhelming advantages in energy density. Suppression of the polysulfide dissolution while maintaining a high sulfur utilization is the main challenge for Li-S batteries. Here, we have designed and synthesized double-shelled nanocages with two shells of cobalt hydroxide and layered double hydroxides (CH@LDH) as a conceptually new sulfur host for Li-S batteries. Specifically, the hollow CH@LDH polyhedra with complex shell structures not only maximize the advantages of hollow nanostructures for encapsulating a high content of sulfur (75 wt %), but also provide sufficient self-functionalized surfaces for chemically bonding with polysulfides to suppress their outward dissolution. When evaluated as cathode material for Li-S batteries, the CH@LDH/S composite shows a significantly improved electrochemical performance.

  10. Antimycobacterial, antimicrobial, and biocompatibility properties of para-aminosalicylic acid with zinc layered hydroxide and Zn/Al layered double hydroxide nanocomposites.

    Science.gov (United States)

    Saifullah, Bullo; El Zowalaty, Mohamed E; Arulselvan, Palanisamy; Fakurazi, Sharida; Webster, Thomas J; Geilich, Benjamin M; Hussein, Mohd Zobir

    2014-01-01

    The treatment of tuberculosis by chemotherapy is complicated due to multiple drug prescriptions, long treatment duration, and adverse side effects. We report here for the first time an in vitro therapeutic effect of nanocomposites based on para-aminosalicylic acid with zinc layered hydroxide (PAS-ZLH) and zinc-aluminum layered double hydroxides (PAS-Zn/Al LDH), against mycobacteria, Gram-positive bacteria, and Gram-negative bacteria. The nanocomposites demonstrated good antimycobacterial activity and were found to be effective in killing Gram-positive and Gram-negative bacteria. A biocompatibility study revealed good biocompatibility of the PAS-ZLH nanocomposites against normal human MRC-5 lung cells. The para-aminosalicylic acid loading was quantified with high-performance liquid chromatography analysis. In summary, the present preliminary in vitro studies are highly encouraging for further in vivo studies of PAS-ZLH and PAS-Zn/Al LDH nanocomposites to treat tuberculosis.

  11. Cobalt hydroxide/oxide hexagonal ring-graphene hybrids through chemical etching of metal hydroxide platelets by graphene oxide: energy storage applications.

    Science.gov (United States)

    Nethravathi, C; Rajamathi, Catherine R; Rajamathi, Michael; Wang, Xi; Gautam, Ujjal K; Golberg, Dmitri; Bando, Yoshio

    2014-03-25

    The reaction of β-Co(OH)2 hexagonal platelets with graphite oxide in an aqueous colloidal dispersion results in the formation of β-Co(OH)2 hexagonal rings anchored to graphene oxide layers. The interaction between the basic hydroxide layers and the acidic groups on graphene oxide induces chemical etching of the hexagonal platelets, forming β-Co(OH)2 hexagonal rings. On heating in air or N2, the hydroxide hybrid is morphotactically converted to porous Co3O4/CoO hexagonal ring-graphene hybrids. Porous NiCo2O4 hexagonal ring-graphene hybrid is also obtained through a similar process starting from β-Ni0.33Co0.67(OH)2 platelets. As electrode materials for supercapacitors or lithium-ion batteries, these materials exhibit a large capacity, high rate capability, and excellent cycling stability.

  12. Calcium supplement: humanity's double-edged sword.

    Science.gov (United States)

    Bunyaratavej, Narong; Buranasinsup, Shutipen

    2011-10-01

    The principle aim of the present study is to investigate the dark side of calcium, pollutions in calcium preparation especially lead (Pb), mercury (Hg) and cadmium (Cd). The collected samples were the different calcium salts in the market and 18 preparations which were classified into 3 groups: Calcium carbonate salts, Chelated calcium and natural-raw calcium. All samples were analyzed for lead, cadmium and mercury by inductively Coupled Plasma Mass Spectrometry (ICP-MS) technique, in house method based on AOAC (2005) 999.10 by ICP-MS. The calcium carbonate and the natural-raw calcium in every sample contained lead at 0.023-0.407 mg/kg of calcium powder. Meanwhile, the natural-raw calcium such as oyster, coral and animal bone showed amount of lead at 0.106-0.384 mg/kg with small amounts of mercury and cadmium. The chelated calcium such as calcium gluconate, calcium lactate and calcium citrate are free of lead.

  13. Development of Drug Delivery Systems Based on Layered Hydroxides for Nanomedicine

    Directory of Open Access Journals (Sweden)

    Farahnaz Barahuie

    2014-05-01

    Full Text Available Layered hydroxides (LHs have recently fascinated researchers due to their wide application in various fields. These inorganic nanoparticles, with excellent features as nanocarriers in drug delivery systems, have the potential to play an important role in healthcare. Owing to their outstanding ion-exchange capacity, many organic pharmaceutical drugs have been intercalated into the interlayer galleries of LHs and, consequently, novel nanodrugs or smart drugs may revolutionize in the treatment of diseases. Layered hydroxides, as green nanoreservoirs with sustained drug release and cell targeting properties hold great promise of improving health and prolonging life.

  14. Studies on Thorium Adsorption Characteristics upon Activated Titanium Hydroxide Prepared from Rosetta Ilmenite Concentrate

    Energy Technology Data Exchange (ETDEWEB)

    Gado, M, E-mail: parq28@yahoo.com; Zaki, S [Nuclear Materials Authority, P. O. Box 530 El Maadi, Cairo (Egypt)

    2016-01-01

    The titanium hydroxide prepared from Rosetta ilmenite concentrate has been applied for Th (IV) adsorption from its acid aqueous solutions. The prepared hydroxide is first characterized by both Fourier transform infrared (FT-IR) spectrum and thermogravimetric analysis. The relevant factors affecting the adsorption process have been studied. The obtained equilibrium data fits well with the Langmuir isotherm rather than Freundlich isotherm, while the adsorption kinetic data follow the pseudo-second order model. The different thermodynamic parameters have also been calculated and indicate that the adsorption process is spontaneous.

  15. Sulfur removal from Gediz lignite using aqueous sodium hydroxide solutions under mild oxidative conditions

    Energy Technology Data Exchange (ETDEWEB)

    Yaman, S.; Kuecuekbayrak, S. [Istanbul Technical Univ. (Turkey). Chemical and Metallurgical Engineering Faculty

    1999-11-01

    Sulfur removal from a high-sulfur Turkish lignite (Gediz) using aqueous sodium hydroxide solutions having dissolved oxygen was investigated under mild oxidative conditions. Effects of the parameters such as sodium hydroxide/lignite weight ratio, temperature, and partial pressure of oxygen were investigated within the ranges of 0.05--0.8, 423--498 K, and 1--2 MPa, respectively. Optimum values of these parameters were determined regarding sulfur removal and coal recovery. Influences of dry oxidation of the lignite sample as a pretreatment at 573 K and subsequent washing of some treated lignite samples with 1 N HCl were investigated.

  16. Synthesis and Characterization of Layered Double Hydroxides Containing Optically Active Transition Metal Ion

    Science.gov (United States)

    Tyagi, S. B.; Kharkwal, Aneeta; Nitu; Kharkwal, Mamta; Sharma, Raghunandan

    2017-01-01

    The acetate intercalated layered double hydroxides of Zn and Mn, have been synthesized by chimie douce method. The materials were characterized by XRD, TGA, CHN, IR, XPS, SEM-EDX and UV-visible spectroscopy. The photoluminescence properties was also studied. The optical properties of layered hydroxides are active transition metal ion dependent, particularly d1-10 system plays an important role. Simultaneously the role of host - guest orientation has been considered the basis of photoluminescence. Acetate ion can be exchanged with iodide and sulphate ions. The decomposed product resulted the pure phase Mn doped zinc oxide are also reported.

  17. Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides.

    Science.gov (United States)

    Papassiopi, N; Vaxevanidou, K; Christou, C; Karagianni, E; Antipas, G S E

    2014-01-15

    Chromium is a common contaminant of soils and aquifers and constitutes a major environmental problem. In nature, chromium usually exists in the form of two oxidation states, trivalent, Cr(III), which is relatively innocuous for biota and for the aquatic environment, and hexavalent, Cr(VI) which is toxic, carcinogenic and very soluble. Accordingly, the majority of wastewater and groundwater treatment technologies, include a stage where Cr(VI) is reduced to Cr(III), in order to remove chromium from the aqueous phase and bind the element in the form of environmentally stable solid compounds. In the absence of iron the final product is typically of the form Cr(OH)3·xH2O whereas in the presence of iron the precipitate is a mixed Fe(1-x)Crx(OH)3 phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fex,Cr1-x)(OH)3 hydroxides as compared to the stability of Cr(OH)3. We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH)3·3H2O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH)3(am) phase. Mixed Fe0.75Cr0.25(OH)3 hydroxides were found to be of the ferrihydrite structure, Fe(OH)3, and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe(III)-Cr(III) hydroxides are more effective enhancers of groundwater quality, in comparison to the plain amorphous or crystalline Cr(III) hydroxides, the latter found to have a solubility typically higher than 50μg/l (maximum EU permitted Cr level in drinking water), while the amorphous Cr(OH)3(am) phase was within the drinking water threshold in the range 5.7hydroxides studied were of extended stability in the 4.8

  18. Large-scale simulations of layered double hydroxide nanocomposite materials

    Science.gov (United States)

    Thyveetil, Mary-Ann

    Layered double hydroxides (LDHs) have the ability to intercalate a multitude of anionic species. Atomistic simulation techniques such as molecular dynamics have provided considerable insight into the behaviour of these materials. We review these techniques and recent algorithmic advances which considerably improve the performance of MD applications. In particular, we discuss how the advent of high performance computing and computational grids has allowed us to explore large scale models with considerable ease. Our simulations have been heavily reliant on computational resources on the UK's NGS (National Grid Service), the US TeraGrid and the Distributed European Infrastructure for Supercomputing Applications (DEISA). In order to utilise computational grids we rely on grid middleware to launch, computationally steer and visualise our simulations. We have integrated the RealityGrid steering library into the Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) 1 . which has enabled us to perform re mote computational steering and visualisation of molecular dynamics simulations on grid infrastruc tures. We also use the Application Hosting Environment (AHE) 2 in order to launch simulations on remote supercomputing resources and we show that data transfer rates between local clusters and super- computing resources can be considerably enhanced by using optically switched networks. We perform large scale molecular dynamics simulations of MgiAl-LDHs intercalated with either chloride ions or a mixture of DNA and chloride ions. The systems exhibit undulatory modes, which are suppressed in smaller scale simulations, caused by the collective thermal motion of atoms in the LDH layers. Thermal undulations provide elastic properties of the system including the bending modulus, Young's moduli and Poisson's ratios. To explore the interaction between LDHs and DNA. we use molecular dynamics techniques to per form simulations of double stranded, linear and plasmid DNA up

  19. Antimycobacterial, antimicrobial, and biocompatibility properties of para-aminosalicylic acid with zinc layered hydroxide and Zn/Al layered double hydroxide nanocomposites

    Directory of Open Access Journals (Sweden)

    Saifullah B

    2014-07-01

    Full Text Available Bullo Saifullah,1 Mohamed E El Zowalaty,2,3 Palanisamy Arulselvan,2 Sharida Fakurazi,2,4 Thomas J Webster,5,6 Benjamin M Geilich,5 Mohd Zobir Hussein1 1Materials Synthesis and Characterization Laboratory, Institute of Advanced Technology (ITMA, Universiti Putra Malaysia, Serdang, Selangor, Malaysia; 2Laboratory of Vaccines and Immunotherapeutics, Institute of Bioscience, Universiti Putra Malaysia, Serdang, Selangor, Malaysia; 3Department of Environmental Health, Faculty of Public Health and Tropical Medicine, Jazan University, Jazan, Saudi Arabia; 4Department of Human Anatomy, Faculty of Medicine and Health Science, Universiti Putra Malaysia, Serdang, Selangor, Malaysia; 5Department of Chemical Engineering and Program in Bioengineering, Northeastern University, Boston, MA, USA; 6Center of Excellence for Advanced Materials Research, King Abdulaziz University, Jeddah, Saudi Arabia Abstract: The treatment of tuberculosis by chemotherapy is complicated due to multiple drug prescriptions, long treatment duration, and adverse side effects. We report here for the first time an in vitro therapeutic effect of nanocomposites based on para-aminosalicylic acid with zinc layered hydroxide (PAS-ZLH and zinc-aluminum layered double hydroxides (PAS-Zn/Al LDH, against mycobacteria, Gram-positive bacteria, and Gram-negative bacteria. The nanocomposites demonstrated good antimycobacterial activity and were found to be effective in killing Gram-positive and Gram-negative bacteria. A biocompatibility study revealed good biocompatibility of the PAS-ZLH nanocomposites against normal human MRC-5 lung cells. The para-aminosalicylic acid loading was quantified with high-performance liquid chromatography analysis. In summary, the present preliminary in vitro studies are highly encouraging for further in vivo studies of PAS-ZLH and PAS-Zn/Al LDH nanocomposites to treat tuberculosis.  Keywords: Zn/Al-layered double hydroxides, zinc layered hydroxides, tuberculosis, para

  20. A facile one-pot synthesis of ruthenium hydroxide nanoparticles on magnetic silica: Aqueous hydration of nitriles to amides

    Science.gov (United States)

    One-pot synthesis of ruthenium hydroxide nanoparticles on magnetic silica is described which involve the in situ generation of magnetic silica (Fe3O4@ SiO2) and ruthenium hydroxide immobilization; the hydration of nitriles occurs in high yield and excellent selectivity using this...

  1. The effect of variable calcium and very low calcium diets on human calcium metabolism. Ph.D. Thesis. Final Report

    Science.gov (United States)

    Chu, J.

    1971-01-01

    The effects of a very low calcium diet, with variable high and low protein intake, on the dynamics of calcium metabolism and the mechanism of calciuretics, are examined. The experiment, using male subjects, was designed to study the role of intestinal calcium absorption on urinary calcium excretion, and the rate of production of endogeneously secreted calcium in the gastrointestinal tract. The study showed an average of 70% fractional absorption rate during very low calcium intake, and that a decrease in renal tubular reabsorption of calcium is responsible for calciuretic effects of high protein intake. The study also indicates that there is a tendency to develop osteoporosis after long periods of low calcium intake, especially with a concurrent high protein intake.

  2. Catalytic wet peroxide oxidation of azo dye (Direct Blue 15) using solvothermally synthesized copper hydroxide nitrate as catalyst.

    Science.gov (United States)

    Zhan, Yuzhong; Zhou, Xiang; Fu, Bei; Chen, Yiliang

    2011-03-15

    Copper hydroxide nitrate (Cu(2)(OH)(3)NO(3)) was synthesized solvothermally in anhydrous ethanol and characterized by XRD, FTIR, TG-DTA and SEM. The peroxide degradation of an azo dye (Direct Blue 15) on this material was evaluated by examining catalyst loading, initial pH, hydrogen peroxide dosage, initial dye concentration and temperature. The leaching of Cu from the copper hydroxide nitrate during the reaction was also measured. The copper hydroxide nitrate synthesized solvothermally, which was of a novel spherical morphology with complex secondary structures and contained high-dispersed Cu(2)O impurity, showed good performance for oxidation degradation of the azo dye, especially high catalytic activity, high utilization of hydrogen peroxide and a wide pH range, whereas the copper hydroxide nitrate synthesized by the direct reaction of copper nitrate and sodium hydroxide showed low catalytic activity.

  3. Utilization of Magnesium Hydroxide Produced by Magnesia Hydration as Fire Retardant for Nylon 6-6,6

    Directory of Open Access Journals (Sweden)

    Rocha Sônia D.F.

    2001-01-01

    Full Text Available The present work investigates the use of magnesium hydroxide, produced by magnesia hydration, as a fire retardant in polymers. The hydration was carried out in an autoclave, at temperature of 130°C for 1 hour, and the product was further submitted to cominution in a jet mill. The solids were characterized with regard to their chemical composition, particle size distribution, surface area and morphology. The performance evaluation of the hydroxide as a flame retardant for a copolymer of nylon 6-6,6 was carried out according to the UL94 specifications for vertical burning tests. V-0 flammability rating at 1.6 mm (60% magnesium hydroxide-filled nylon composite and at 3.2 mm (40% magnesium hydroxide filled nylon composite were achieved. Mechanical properties were maintained at the desired values. These results indicate that the hydroxide obtained from magnesia hydration can be successfully employed as a fire retardant for nylon 6-6,6.

  4. 双(羟基)金属复合氧化物的表面改性%Surface Modification of Layered Double Hydroxide

    Institute of Scientific and Technical Information of China (English)

    冯春瑶; 矫庆泽; 李蕾; 张春英; 段雪

    2001-01-01

    Mg/Al layered double hydroxide(LDH) was treated with stearic acid by a wet method. The modified double hydroxide showed good dispersion and floatation property with their layer structure being remained almost unchanged.

  5. Vitamin D and intestinal calcium absorption.

    Science.gov (United States)

    Christakos, Sylvia; Dhawan, Puneet; Porta, Angela; Mady, Leila J; Seth, Tanya

    2011-12-05

    The principal function of vitamin D in calcium homeostasis is to increase calcium absorption from the intestine. Calcium is absorbed by both an active transcellular pathway, which is energy dependent, and by a passive paracellular pathway through tight junctions. 1,25Dihydroxyvitamin D(3) (1,25(OH)(2)D(3)) the hormonally active form of vitamin D, through its genomic actions, is the major stimulator of active intestinal calcium absorption which involves calcium influx, translocation of calcium through the interior of the enterocyte and basolateral extrusion of calcium by the intestinal plasma membrane pump. This article reviews recent studies that have challenged the traditional model of vitamin D mediated transcellular calcium absorption and the crucial role of specific calcium transport proteins in intestinal calcium absorption. There is also increasing evidence that 1,25(OH)(2)D(3) can enhance paracellular calcium diffusion. The influence of estrogen, prolactin, glucocorticoids and aging on intestinal calcium absorption and the role of the distal intestine in vitamin D mediated intestinal calcium absorption are also discussed.

  6. Calcium electroporation in three cell lines; a comparison of bleomycin and calcium, calcium compounds, and pulsing conditions

    DEFF Research Database (Denmark)

    Frandsen, Stine Krog; Gissel, Hanne; Hojman, Pernille;

    2013-01-01

    electroporation and electrochemotherapy. METHODS: The effects of calcium electroporation and bleomycin electroporation (alone or in combination) were compared in three different cell lines (DC-3F, transformed Chinese hamster lung fibroblast; K-562, human leukemia; and murine Lewis Lung Carcinoma). Furthermore...... survival at similar applied voltage parameters. The effect of calcium electroporation is independent of calcium compound. GENERAL SIGNIFICANCE: This study strongly supports the use of calcium electroporation as a potential cancer therapy and the results may aid in future clinical trials....

  7. The effect of calcium gluconate and other calcium supplements as a dietary calcium source on magnesium absorption in rats.

    Science.gov (United States)

    Chonan, O; Takahashi, R; Yasui, H; Watanuki, M

    1997-01-01

    The effects of commercially available calcium supplements (calcium carbonate, calcium gluconate, oyster shell preparation and bovine bone preparation) and gluconic acid on the absorption of calcium and magnesium were evaluated for 30 days in male Wistar rats. There were no differences in the apparent absorption ratio of calcium among rats fed each calcium supplement; however, the rats fed the calcium gluconate diet had a higher apparent absorption ratio of magnesium than the rats fed the other calcium supplements. Dietary gluconic acid also more markedly stimulated magnesium absorption than the calcium carbonate diet, and the bone (femur and tibia) magnesium contents of rats fed the gluconic acid diet were significantly higher than those of the rats fed the calcium carbonate diet. Furthermore, the weight of cecal tissue and the concentrations of acetic acid and butyric acid in cecal digesta of rats fed the calcium gluconate diet or the gluconic acid diet were significantly increased. We speculate that the stimulation of magnesium absorption in rats fed the calcium gluconate diet is a result of the gluconic acid component and the effect of gluconic acid on magnesium absorption probably results from cecal hypertrophy, magnesium solubility in the large intestine and the effects of volatile fatty acids on magnesium absorption.

  8. Estimation of presynaptic calcium currents and endogenous calcium buffers at the frog neuromuscular junction with two different calcium fluorescent dyes

    Directory of Open Access Journals (Sweden)

    Dmitry eSamigullin

    2015-01-01

    Full Text Available At the frog neuromuscular junction, under physiological conditions, the direct measurement of calcium currents and of the concentration of intracellular calcium buffers—which determine the kinetics of calcium concentration and neurotransmitter release from the nerve terminal—has hitherto been technically impossible. With the aim of quantifying both Ca2+ currents and the intracellular calcium buffers, we measured fluorescence signals from nerve terminals loaded with the low-affinity calcium dye Magnesium Green or the high-affinity dye Oregon Green BAPTA-1, simultaneously with microelectrode recordings of nerve-action potentials and end-plate currents. The action-potential-induced fluorescence signals in the nerve terminals developed much more slowly than the postsynaptic response. To clarify the reasons for this observation and to define a spatiotemporal profile of intracellular calcium and of the concentration of mobile and fixed calcium buffers, mathematical modeling was employed. The best approximations of the experimental calcium transients for both calcium dyes were obtained when the calcium current had an amplitude of 1.6 ± 0.08 рА and a half-decay time of 1.2 ± 0.06 ms, and when the concentrations of mobile and fixed calcium buffers were 250 ± 13 µM and 8 ± 0.4 mM, respectively. High concentrations of endogenous buffers define the time course of calcium transients after an action potential in the axoplasm, and may modify synaptic plasticity.

  9. Aqueous Ammonia or Ammonium Hydroxide? Identifying a Base as Strong or Weak

    Science.gov (United States)

    Sanger, Michael J.; Danner, Matthew

    2010-01-01

    When grocery stores sell solutions of ammonia, they are labeled "ammonia"; however, when the same solution is purchased from chemical supply stores, they are labeled "ammonium hydroxide". The goal of this experiment is for students to determine which name is more appropriate. In this experiment, students use several different experimental methods…

  10. Structure and properties of alizarin complex formed with alkali metal hydroxides in methanol solution.

    Science.gov (United States)

    Jeliński, Tomasz; Cysewski, Piotr

    2016-06-01

    Quantum chemical computations were used for prediction of the structure and color of alizarin complex with alkali metal hydroxides in methanolic solutions. The color prediction relying on the single Gaussian-like band once again proved the usefulness of the PBE0 density functional due to the observed smallest color difference between computed and experimentally derived values. It was found that the alkali metal hydroxide molecules can bind to the two oxygen atoms of both hydroxyl groups of alizarin or to one of these atoms and the oxygen atom from the keto group in a complex with three methanol molecules. This means that two electronic transitions need to be taken into account when considering the spectra of the studied complexes. The resulting bond lengths and angles are correlated with the properties of the alkali metal atoms. The molar mass, the atomic radius, and the Pauling electronegativity of studied metals are quite accurate predictors of the geometric properties of hydroxide complexes with alizarin in methanol solution. Graphical abstract The spectra of the neutral and monoanionic form of alizarin together with color changes resulting from addition of different metal hydroxides and represented in CIE color space.

  11. Migration of nanosized layered double hydroxide platelets from polylactide nanocomposite films

    DEFF Research Database (Denmark)

    Schmidt, Bjørn; Katiyar, Vimal; Plackett, David

    2011-01-01

    Melt-extruded L-polylactide (PLA) nanocomposite films were prepared from commercially available PLA and laurate-modified Mg–Al layered double hydroxide (LDH-C12). Three films were tested for total migration as well as specific migration of LDH, tin, laurate and low molecular weight PLA oligomers ...... detected arises from the use of organotin catalysts in the manufacture of PLA....

  12. Preparation of magnesium hydroxide nanoflowers from boron mud via anti-drop precipitation method

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Xi [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Blue Sky Technology Corporation, Beijing 100083 (China); Ma, Hongwen, E-mail: mahw@cugb.edu.cn [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Jiang, Xiaoqian [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Jiang, Zhouqing [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Blue Sky Technology Corporation, Beijing 100083 (China)

    2014-08-15

    Highlights: • We use the anti-drop precipitation method for synthesis of magnesium hydroxide. • Boron mud which is solid waste from a borax factory is used as the magnesium source. • The magnesium hydroxide nanoflowers are prepared in a short time. • The as-prepared magnesium hydroxide can be used as an effective flame retardant. - Abstract: Using boron mud as the starting material, the flower-like magnesium hydroxide (MH) has been successfully prepared via anti-drop precipitation method. The effect of NH{sub 3}·H{sub 2}O concentration, aging time, and surfactant on the morphology of MH was investigated. The optimum precipitation conditions are dropping MgSO{sub 4} solution in 5% NH{sub 3}·H{sub 2}O solution, with 3% polyethylene glycol as surfactant, aging for 30 min. XRD, SEM, FI-IR, and TG/DTA have been employed to characterize the as-prepared samples. XRD reveals that MH with high purity has the brucite structure. SEM images show that the flower-like MH exists in the form of mono-disperse well uniform spherical aggregation with diameter of 3–5 μm. TG/DTA shows a total percentage of weight loss 33.6% with a well-defined endothermic peak near 381.3 °C corresponding to the decomposition of MH. Furthermore, it reports that the extremely fast primary nucleation is of significance for crystal growth of MH.

  13. Hydrothermal Synthesis and Characterization of 3R Polytypes of Mg-Al Layered Double Hydroxides

    NARCIS (Netherlands)

    Budhysutanto, W.N.

    2010-01-01

    Layered Double Hydroxides (LDH) is a unique group of clays that have an anionic exchange capability. This research explored the hydrothermal method as an alternative method to synthesize Mg-Al LDH. It is a simple and more environmentally friendly compared to the conventional method of co-precipitati

  14. Studies on Synthesis and Properties of Mg-Al-nitrate Layered Double Hydroxides

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A positive Mg-Al-nitrate layered double hydroxides (LDHs) has been synthesized using a non-steady coprccipitation method. The shape, size, chemical composition, electrical property and anion exchange property of the positive nanoparticle were studied by SEM, XRD, FTIR,chemical analysis, spectroanalysis and measuring of electrophoretic mobilities. Preliminary results show the positive nanopartiele is a promising precursor ofpolymer/LDHs nanocomposite.

  15. Formation of nematic liquid crystals of sterically stabilized layered double hydroxide platelets

    NARCIS (Netherlands)

    Mourad, M.C.D.; Devid, E.J.; van Schooneveld, M.M.; Vonk, Ch.; Lekkerkerker, H.N.W.

    2008-01-01

    Colloidal platelets of hydrotalcite, a layered double hydroxide, have been prepared by coprecipitation at pH 11−12 of magnesium nitrate and aluminum nitrate at two different magnesium to aluminum ratios. Changing the temperature and ionic strength during hydrothermal treatment, the platelets were ta

  16. Device to generate high purity hydroxide solution in-line for ion chromatography.

    Science.gov (United States)

    Masunaga, Hiroto; Higo, Yuji; Ishii, Mizuo; Maruyama, Noboru; Yamazaki, Shigeo

    2016-05-06

    Herein, we report a new device that generates a high-purity hydroxide solution in line. The device's container has three compartments that are isolated from each other by two cation exchange (CE) membranes. In each end of the container, an electrode is installed. The three compartments are filled with ion exchange resins. A bipolar boundary is a composite boundary comprising anion- and cation-exchangers. This device has two bipolar boundaries, which are used to separate the location of hydroxide solution generation from the location where water is electrolyzed. Therefore, it can produce high-purity hydroxide solutions that are free from gases and anionic impurities. The hydroxide solution is generated on the basis of an electrokinetic phenomenon at the surfaces of ion-exchange resins and membranes in an electric field; NaOH concentration can be controlled at rates from 0.01 to 100mM per 1mL/min by adjusting the electrical current (0-200mA) applied to the device. As the generated solution is used as an eluent for a suppressed anion chromatography, the electrical conductivity of the effluent from the suppressor is as low as that of ultra-pure water. Thus, the noise of the base-line electrical conductivity is improved, and so the detection limit of anions on the sub-ng/mL order can be achieved.

  17. Comparison of the Winograd method and chemical cauterization with 10% sodium hydroxide for treating ingrown toenails

    Directory of Open Access Journals (Sweden)

    Nebahat Demet Akpolat

    2016-09-01

    Full Text Available Background and Design: This study was performed to assess the therapeutic outcomes of the surgical method, described by Winograd and chemical cauterization with sodium hydroxide in patients with Heifetz stage 2 and 3 ingrown toenail (recurrence, complication, improvement and time to regain activity. Materials and Methods: One-hundred patients who presented to the outpatient clinics of orthopedics, general surgery and dermatology with the complaints of pain, redness and discharge in the toenail between January 2010 and January 2012 and who failed to respond to conservative treatment and were diagnosed with Heifetz stage 2 and 3 ingrown toenail. Fifty patients underwent chemical cauterization with sodium hydroxide while 50 underwent Winograd surgery. Results: The patients were followed up for a year at 2-month intervals. While no recurrence was observed in patients who received chemical cauterization, five patients who underwent Winograd surgery had recurrence (p=0.022. Three patients receiving Winograd surgery were found to have superficial wound side infection on postoperative follow-up (p=0.08. Patients, who underwent chemical cauterization with sodium hydroxide, were detected to improve and return to normal activity in a shorter period. Conclusion: Chemical cauterization of the germinal matrix with 10% sodium hydroxide is a convenient method with a low rate of complication and recurrence compared to the Winograd surgery in the treatment of ingrown toenails.

  18. The determination of hydroxide and carbonate in concentrated sodium chloride solutions

    NARCIS (Netherlands)

    Roolvink, W.B.; Bos, M.

    1980-01-01

    A computer method for the determination of carbonate and hydroxide in concentrated (2.89 M) sodium chloride solutions is described. The method is based on multiparametric curve-fitting and can also be applied to salts of dibasic acids with unknown equilibrium constants. The systematic error is not m

  19. The contribution of polyhydroxyl aromatic compounds to tetramethylammonium hydroxide lignin-based proxies

    NARCIS (Netherlands)

    Filley, T.R.; Nierop, K.G.J.; Wang, Y.

    2006-01-01

    A problem inherent in analytical procedures where thermochemolyis or pyrolysis is coupled with in situ methylation by tetramethylammonium hydroxide is the inability to determine if an observed aromatic methoxyl group was originally present as a hydroxyl or a methoxyl functionality. This analytical i

  20. Flame retardancy effect of surface-modified metal hydroxides on linear low density polyethylene

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Metal hydroxides (MAH) consisting of magnesium hydroxide and aluminum hydroxide with a mass ratio of 1:2 were surface-modified by γ-diethoxyphosphorous ester propyldiethoxymethylsilane,boric acid and diphenylsilanediol in xylene under dibutyl tin dilaurate catalyst at 140 ℃.Phosphorus,silicon and boron elements covalently bonded to metal hydroxide particles were detected by X-ray photoelectron spectroscopy.The degradation behavior of the surface-modified MAH was characterized by thermogravimetric analysis.The results show that linear low density polyethylene (LLDPE) composite,filled with 50% (mass fraction) of MAH modified by 5.0% (mass fraction) of modifiers,passes the V-O rating of UL-94 test and shows the limited oxygen index of 34%,and its heat release rate and average effective heat combustion in a cone calorimeter measurement decrease obviously;The mechanical properties of MAH can be improved by surface-modification.The uniform dispersion of particles and strong interfacial bonding between particles and matrix are obtained.

  1. Different approaches to the analysis of small angle scattering experiments on porous aluminum-hydroxide

    DEFF Research Database (Denmark)

    Rasmussen, F.B.

    2001-01-01

    Different approaches to the analysis of Small Angle X-ray Scattering experiments on the porous aluminum-hydroxide pseudo-boehmite are compared. Experimental data is analyzed both as scattering from mass fractal aggregates and polydisperse collections of anisotropic particles. Both types of analys...

  2. Inhibition of pH fronts in corrosion cells due to the formation of cerium hydroxide

    NARCIS (Netherlands)

    Soestbergen, M. van; Erich, S.J.F.; Huinink, H.P.; Adan, O.C.G.

    2013-01-01

    The effect of cerium-based corrosion inhibitors on the pH front between the alkaline cathode and acidic anode in corrosion cells has been studied. The cerium component of these inhibitors can affect the pH front since it precipitates in an alkaline environment as cerium hydroxide, which is important

  3. Synthesis of aluminum oxy-hydroxide nanofibers from porous anodic alumina.

    Science.gov (United States)

    Jha, Himendra; Kikuchi, Tatsuya; Sakairi, Masatoshi; Takahashi, Hideaki

    2008-10-01

    A novel method for the synthesis of aluminum oxy-hydroxide nanofibers from a porous anodic oxide film of aluminum is demonstrated. In the present method, the porous anodic alumina not only acts as a template, but also serves as the starting material for the synthesis. The porous anodic alumina film is hydrothermally treated for pore-sealing, which forms aluminum oxy-hydroxide inside the pores of the oxide film as well as on the surface of the film. The hydrothermally sealed porous oxide film is immersed in the sodium citrate solution, which selectively etches the porous aluminum oxide from the film, leaving the oxy-hydroxide intact. The method is simple and gives highly uniform aluminum oxy-hydroxide nanofibers. Moreover, the diameter of the nanofibers can be controlled by controlling the pore size of the porous anodic alumina film, which depends on the anodizing conditions. Nanofibers with diameters of about 38-85 nm, having uniform shape and size, were successfully synthesized using the present method.

  4. Speciation of heavy metal ions as influenced by interactions with montmorillonite, Al hydroxide polymers and citrate.

    NARCIS (Netherlands)

    Janssen, R.P.T.

    1995-01-01

    Clay minerals, metal-hydroxides and organic matter can bind metal ions; moreover they also interact with each other. These mutual interactions influence the metal binding to a significant extent. In this study, the speciation of the heavy metal ions Zn and Ph was investigated in model systems consis

  5. Molecular dynamic simulations of iron (II) hydroxide in high temperature and supercritical water

    Science.gov (United States)

    Meng, Yuanliang

    In this study, the iron (II) hydroxide -- water system has been investigated at high temperatures by using molecular dynamics (MD) simulations. The simulation results reveal that at infinite dilution both Fe2+ cation and OH- anion have 6 water molecules within their first hydration shell and both types of ionic species experience a dramatic increase in their diffusion coefficients at near and supercritical conditions. The process of iron (II) hydroxide cluster formation has been simulated. The nano-clusters of larger sizes formed in supercritical water tend to be in an amorphous state. After having been quenched by an inert gas bath, iron (II) hydroxide nano-clusters with various structures have been produced. The geometries and associated binding energies of these species are given in detail. The vibrational spectra of iron (II) hydroxide clusters are also derived and compared with the spectrum of a bulk solid. The obtained results have a practical value for the analysis of potential corrosion products in supercritical water-cooled reactor (SCWR) which is employed in the new generation nuclear power plant design (GEN IV). This work also illustrates the process of hydrothermal synthesis of oxide nano-particles.

  6. Electrocatalysis and electroanalysis of nickel, its oxides, hydroxides and oxyhydroxides toward small molecules.

    Science.gov (United States)

    Miao, Yuqing; Ouyang, Lei; Zhou, Shilin; Xu, Lina; Yang, Zhuoyuan; Xiao, Mingshu; Ouyang, Ruizhuo

    2014-03-15

    The electrocatalysis toward small molecules, especially small organic compounds, is of importance in a variety of areas. Nickel based materials such as nickel, its oxides, hydroxides as well as oxyhydroxides exhibit excellent electrocatalysis performances toward many small molecules, which are widely used for fuel cells, energy storage, organic synthesis, wastewater treatment, and electrochemical sensors for pharmaceutical, medical, food or environmental analysis. Their electrocatalytic mechanisms are proposed from three aspects such as Ni(OH)2/NiOOH mediated electrolysis, direct electrocatalysis of Ni(OH)2 or NiOOH. Under exposure to air or aqueous solution, two distinct layers form on the Ni surface with a Ni hydroxide layer at the air-oxide interface and an oxide layer between the metal substrate and the outer hydroxide layer. The transformation from nickel or its oxides to hydroxides or oxyhydroxides could be further speeded up in the strong alkaline solution under the cyclic scanning at relatively high positive potential. The redox transition between Ni(OH)2 and NiOOH is also contributed to the electrocatalytic oxidation of Ni and its oxides toward small molecules in alkaline media. In addition, nickel based materials or nanomaterials, their preparations and applications are also overviewed here.

  7. Determination of Aluminium Content in Aluminium Hydroxide Formulation by FT-NIR Transmittance Spectroscopy

    DEFF Research Database (Denmark)

    Lai, Xuxin; Zheng, Yiwu; Søndergaard, Ib;

    2007-01-01

    A method for determining the aluminium content of an aluminium hydroxide suspension using near infrared (NIR) transmittance spectroscopy has been developed. Inductively coupled plasma-atomic emission spectroscopy (ICP-AES) was used as reference method. The factors influencing the NIR analysis...

  8. Optimization of layered double hydroxide stability and adsorption capacity for anionic surfactants

    NARCIS (Netherlands)

    Schouten, Natasja; Ham, Louis G.J. van der; Euverink, Gert-Jan W.; Haan, André B. de

    2007-01-01

    Low cost adsorption technology offers high potential to clean up laundry rinsing water. From an earlier selection of adsorbents, layered double hydroxide (LDH) proved to be an interesting material for the removal of anionic surfactant, linear alkyl benzene sulfonate (LAS) which is the main contamina

  9. Glycine buffered synthesis of layered iron(II)-iron(III) hydroxides (green rusts)

    DEFF Research Database (Denmark)

    Yin, Weizhao; Huang, Lizhi; Pedersen, Emil Bjerglund;

    2016-01-01

    Layered Fe(II)-Fe(III) hydroxides (green rusts, GRs) are efficient reducing agents against oxidizing contaminants such as chromate, nitrate, selenite, and nitroaromatic compounds and chlorinated solvents. In this study, we adopted a buffered precipitation approach where glycine (GLY) was used in ...

  10. Optimization of layered double hydroxide stability and adsorption capacity for anionic surfactants

    NARCIS (Netherlands)

    Schouten, Natasja; Ham, van der Louis G.J.; Euverink, Gert-Jan W.; Haan, de André B.

    2007-01-01

    Low cost adsorption technology offers high potential to clean up laundry rinsing water. From an earlier selection of adsorbents (Schouten et al. 2007), layered double hydroxide (LDH) proved to be an interesting material for the removal of anionic surfactant, linear alkyl benzene sulfonate (LAS) whic

  11. ADSORPTION OF PITCH AND STICKIES ON MAGNESIUM ALUMINUM HYDROXIDES TREATED AT DIFFERENT TEMPERAURES

    Directory of Open Access Journals (Sweden)

    Guodong Li

    2011-04-01

    Full Text Available Magnesium aluminum hydroxides (MAH of nitrate and carbonate forms were prepared by co-precipitation, dried at different temperatures, and employed as an adsorbent for pitch and stickies in papermaking. Results indicated that MAH that had been heat-treated had higher adsorption capacity to model pitch and stickies at neutral pH. Low-temperature-dried magnesium aluminum hydroxides of nitrate form (MAH-NO3 had higher adsorption capacity to model pitch and model stickies than those of the carbonate form (MAH-CO3. Increasing the drying temperature of MAH reduced the difference of adsorption capacity between MAH-NO3 and MAH-CO3. Higher-temperature-dried magnesium aluminum hydroxides also showed higher adsorption capacity to model pitch and stickies when the drying temperature was lower than 550 oC. MAH displayed higher adsorption capacity while a lower initial adsorption rate of model stickies than of model pitch. The model pitch and stickies were adsorbed on MAH significantly by charge neutralization and distributed mainly on the surface of the platelets of magnesium aluminum hydroxides. The experimental isothermal adsorption data of model pitch and stickies on MAH dried at 500 oC fit well to the Freundlich and Dubinin–Radushkevich isotherm equations.

  12. Mechanism of store-operated calcium entry

    Indian Academy of Sciences (India)

    Devkanya Dutta

    2000-12-01

    Activation of receptors coupled to the phospholipase C/IP3 signalling pathway results in a rapid release of calcium from its intracellular stores, eventually leading to depletion of these stores. Calcium store depletion triggers an influx of extracellular calcium across the plasma membrane, a mechanism known as the store-operated calcium entry or capacitative calcium entry. Capacitative calcium current plays a key role in replenishing calcium stores and activating various physiological processes. Despite considerable efforts, very little is known about the molecular nature of the capacitative channel and the signalling pathway that activates it. This review summarizes our current knowledge about store operated calcium entry and suggests possible hypotheses for its mode of activation.

  13. The ins and outs of mitochondrial calcium.

    Science.gov (United States)

    Finkel, Toren; Menazza, Sara; Holmström, Kira M; Parks, Randi J; Liu, Julia; Sun, Junhui; Liu, Jie; Pan, Xin; Murphy, Elizabeth

    2015-05-22

    Calcium is thought to play an important role in regulating mitochondrial function. Evidence suggests that an increase in mitochondrial calcium can augment ATP production by altering the activity of calcium-sensitive mitochondrial matrix enzymes. In contrast, the entry of large amounts of mitochondrial calcium in the setting of ischemia-reperfusion injury is thought to be a critical event in triggering cellular necrosis. For many decades, the details of how calcium entered the mitochondria remained a biological mystery. In the past few years, significant progress has been made in identifying the molecular components of the mitochondrial calcium uniporter complex. Here, we review how calcium enters and leaves the mitochondria, the growing insight into the topology, stoichiometry and function of the uniporter complex, and the early lessons learned from some initial mouse models that genetically perturb mitochondrial calcium homeostasis.

  14. Familial hypocalciuric hypercalcemia and calcium sensing receptor

    DEFF Research Database (Denmark)

    Mrgan, Monija; Nielsen, Sanne; Brixen, Kim

    2014-01-01

    Familial hypocalciuric hypercalcemia (FHH) is a lifelong, benign autosomal dominant disease characterized by hypercalcemia, normal to increased parathyroid hormone level, and a relatively low renal calcium excretion. Inactivation of the calcium-sensing receptor in heterozygous patients results in...

  15. Decalcification of calcium polycarbophil in rats.

    Science.gov (United States)

    Yamada, T; Saito, T; Takahara, E; Nagata, O; Tamai, I; Tsuji, A

    1997-03-01

    The in vivo decalcification of calcium polycarbophil was examined. The decalcification ratio of [45Ca]calcium polycarbophil in the stomach after oral dosing to rats was more than 70% at each designated time and quite closely followed in the in vitro decalcification curve, indicating that the greater part of the calcium ion is released from calcium polycarbophil under normal gastric acidic conditions. The residual radioactivity in rat gastrointestine was nearly equal to that after oral administration of either [45Ca]calcium chloride + polycarbophil. The serum level of radioactivity was nearly equal to that after oral dosing of [45Ca]calcium lactate. These results indicate that the greater part of orally administered calcium polycarbophil released calcium ions to produce polycarbophil in vivo.

  16. Effect of calcium treatment on texture of canned apple solid pack%钙处理对干装苹果罐头质地的影响

    Institute of Scientific and Technical Information of China (English)

    张海燕; 张永茂; 张芳; 康三江; 张霁红; 曾朝珍

    2013-01-01

    采用质地多面分析方法(TPA),以清水处理为对照,研究碱性钙(氧化钙、氢氧化钙)、无机钙(氯化钙、碳酸钙、硫酸钙)、有机钙(乳酸钙、醋酸钙、丙酸钙)对干装苹果罐头质地参数(硬度、回复性、弹性指数、咀嚼性、内聚性)的影响,并对TPA参数之间及其与感官品质间的相关性进行了研究.结果表明:与对照相比,除硫酸钙以外,各处理对干装苹果罐头质地均有明显的影响,经碱性钙(氧化钙和氢氧化钙)处理的干装苹果罐头硬度适中,回复性、弹性指数、咀嚼性、内聚性、感官品质均较好.回复性、弹性指数、咀嚼性、内聚性之间的相关性均显著,硬度与感官品质之间呈显著正相关关系.表明碱性钙对干装苹果罐头有较好的作用,并保持良好的质构.%In order to study the effect of calcium treatment as alkaline calcium(calcium oxide,calcium hydroxide), inorganic calcium (calcium chloride, calcium carbonate, calcium sulfate), organic calcium (calcium lactate,calcium acetate, calcium propionate) on texture parameters (hardness, resilience, flexibility index, chewiness, cohesiveness) ,the texture profile analysis(TPA) was used.At that time, the correlation between TPA parameters and sensory quality were studied.The results showed that each treatment had significant impact on texture of canned apple solid pack.The hardness was moderate,and resilience,flexibility index,chewiness,cohesiveness, sensory quality were better by alkaline calcium treatment.The correlation between resilience, flexibility index, chewiness and cohesiveness were significant, and there was a significant positive correlation between the hardness and sensory quality.Alkaline calcium treatment had good effect on canned apple solid pack, and maintained good texture.

  17. An Aluminum Magnesium Hydroxide Stearate-based Skin Barrier Protection Cream Used for the Management of Eczematous Dermatitis: A Summary of Completed Studies.

    Science.gov (United States)

    Del Rosso, James Q; Bhambri, Sanjay; Michaels, Brent

    2008-11-01

    Eczematous dermatoses can often be very difficult to treat. An aluminum magnesium hydroxide stearate-based cream has recently become available for clinical use. Aluminum magnesium hydroxide stearate-based cream provides an alternative option in treating these dermatoses while providing barrier protection against external allergens and irritants. This article reviews various studies evaluating aluminum magnesium hydroxide stearate-based cream.

  18. Calcium channel blockers and Alzheimer's disease

    Institute of Scientific and Technical Information of China (English)

    Yi Tan; Yulin Deng; Hong Qing

    2012-01-01

    Alzheimer's disease is characterized by two pathological hallmarks: amyloid plaques and neurofi-brillary tangles. In addition, calcium homeostasis is disrupted in the course of human aging. Recent research shows that dense plaques can cause functional alteration of calcium signals in mice with Alzheimer's disease. Calcium channel blockers are effective therapeutics for treating Alzheimer's disease. This review provides an overview of the current research of calcium channel blockers in-volved in Alzheimer's disease therapy.

  19. Variable efficacy of calcium carbonate tablets.

    Science.gov (United States)

    Kobrin, S M; Goldstein, S J; Shangraw, R F; Raja, R M

    1989-12-01

    Orally administered calcium carbonate tablets are commonly prescribed as a calcium supplement and for their phosphate-binding effects in renal failure patients. Two cases are reported in which a commercially available brand of calcium carbonate tablets appeared to be ineffective. Formal investigation of the bioavailability of this product revealed it to have impaired disintegration and dissolution and a lack of clinical efficacy. Recommendations that will enable physicians to avoid prescribing and pharmacists to avoid dispensing ineffective calcium carbonate tablets are proposed.

  20. Calcium regulation in endosymbiotic organelles of plants

    OpenAIRE

    Bussemer, Johanna; Vothknecht, Ute C.; Chigri, Fatima

    2009-01-01

    In plant cells calcium-dependent signaling pathways are involved in a large array of biological processes in response to hormones, biotic/abiotic stress signals and a variety of developmental cues. This is generally achieved through binding of calcium to diverse calcium-sensing proteins, which subsequently control downstream events by activating or inhibiting biochemical reactions. Regulation by calcium is considered as a eukaryotic trait and has not been described for prokaryotes. Neverthele...

  1. Teaching Calcium-Induced Calcium Release in Cardiomyocytes Using a Classic Paper by Fabiato

    Science.gov (United States)

    Liang, Willmann

    2008-01-01

    This teaching paper utilizes the materials presented by Dr. Fabiato in his review article entitled "Calcium-induced release of calcium from the cardiac sarcoplasmic reticulum." In the review, supporting evidence of calcium-induced calcium release (CICR) is presented. Data concerning potential objections to the CICR theory are discussed as well. In…

  2. Effective Production of Sorbitol and Mannitol from Sugars Catalyzed by Ni Nanoparticles Supported on Aluminium Hydroxide

    Directory of Open Access Journals (Sweden)

    Rodiansono Rodiansono

    2013-06-01

    Full Text Available Effective production of hexitols (sorbitol and mannitol was achieved from sugars by means of nickel nanoparticles supported on aluminium hydroxide (NiNPs/AlOH catalyst. NiNPs/AlOH catalyst was prepared by a simple and benign environmentally procedure using less amount of sodium hydroxide. ICP-AES and XRD analyses confirmed that the NiNPs/AlOH catalysts comprised a large amount of remained aluminium hydroxide (i.e. bayerite and gibbsite. The presence of aluminium hydroxide caused a high dispersion Ni metal species. The average Ni crystallite sizes that derived from the Scherrer`s equation for former R-Ni and NiNPs/AlOH were 8.6 nm and 4.1 nm, respectively. The catalyst exhibited high activity and selectivity both hydrogenolysis of disaccharides (sucrose and cellobiose and monosaccharides (glucose, fructose, and xylose at 403 K for 24 h. The NiNPs/AlOH catalyst was found to be reusable for at least five consecutive runs without any significant loss of activity and selectivity. © 2013 BCREC UNDIP. All rights reservedReceived: 21st December 2012; Revised: 7th February 2013; Accepted: 10th February 2013[How to Cite: Rodiansono, R., Shimazu, S. (2013. Effective Production of Sorbitol and Mannitol from Sug-ars Catalyzed by Ni Nanoparticles Supported on Aluminium Hydroxide. Bulletin of Chemical Reaction Engineering & Catalysis, 8 (1: 40-46. (doi:10.9767/bcrec.8.1.4290.40-46][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.8.1.4290.40-46] | View in  |

  3. 21 CFR 582.5217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium phosphate. 582.5217 Section 582.5217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5217 Calcium phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic)....

  4. 21 CFR 582.1217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium phosphate. 582.1217 Section 582.1217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1217 Calcium phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic)....

  5. 21 CFR 182.1217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium phosphate. 182.1217 Section 182.1217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Substances § 182.1217 Calcium phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic)....

  6. Abnormalities of serum calcium and magnesium

    Science.gov (United States)

    Neonatal hypocalcemia is defined as a total serum calcium concentration of <7 mg/dL or an ionized calcium concentration of <4 mg/dL (1mmol/L). In very low birth weight (VLBW) infants, ionized calcium values of 0.8 to 1 mmol/L are common and not usually associated with clinical symptoms. In larger in...

  7. Acute calcium homeostasis in MHS swine.

    Science.gov (United States)

    Harrison, G G; Morrell, D F; Brain, V; Jaros, G G

    1987-07-01

    To elucidate a pathogenesis for the reduction in bone calcium content observed in MHS individuals, we studied the acute calcium homeostasis of MHS swine. This was achieved by the serial measurement, with a calcium selective electrode, of calcium transients in Landrace MHS (five) and control Landrace/large white cross MH negative (five) swine following IV bolus injection of calcium gluconate 0.1 mmol X kg-1--a dose which induced an acute 45 per cent increase in plasma ionised calcium. Experimental animals were anaesthetised with ketamine 10 mg X kg-1 IM, thiopentone (intermittent divided doses) 15-25 mg X kg-1 (total) IV and N2O/O2 (FIO2 0.3) by IPPV to maintain a normal blood gas, acid/base state. The plasma ionised calcium decay curve observed in MHS swine did not differ from that of control normal swine. Further it was noted that the induced acute rise in plasma ionised calcium failed to trigger the MH syndrome in any MHS swine. It is concluded that the mechanisms of acute calcium homeostasis in MHS swine are normal. An explanation for the reduction in bone calcium content observed in MHS individuals must be sought, therefore, through study of the slow long-term component of the calcium regulatory process. In addition, the conventional strictures placed on the use, in MHS patients, of calcium gluconate are called in question.

  8. Multifaceted Role of Calcium in Cancer.

    Science.gov (United States)

    Sarode, Gargi S; Sarode, Sachin C; Patil, Shankargouda

    2017-01-01

    Role of calcium in bone remodeling and tooth remineral-ization is well known. However, calcium also plays a very imperative role in many biochemical reactions, which are essential for normal functioning of cells. The calcium associated tissue homeostasis encompasses activities like proliferation, cell death, cell motility, oxygen, and nutrient supply.

  9. 21 CFR 582.6219 - Calcium phytate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium phytate. 582.6219 Section 582.6219 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Calcium phytate. (a) Product. Calcium phytate. (b) Conditions of use. This substance is...

  10. 21 CFR 582.3189 - Calcium ascorbate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium ascorbate. 582.3189 Section 582.3189 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL....3189 Calcium ascorbate. (a) Product. Calcium ascorbate. (b) Conditions of use. This substance...

  11. 21 CFR 182.3189 - Calcium ascorbate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium ascorbate. 182.3189 Section 182.3189 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Calcium ascorbate. (a) Product. Calcium ascorbate. (b) Conditions of use. This substance is...

  12. 21 CFR 582.7187 - Calcium alginate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium alginate. 582.7187 Section 582.7187 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Calcium alginate. (a) Product. Calcium alginate. (b) Conditions of use. This substance is...

  13. Stable aerobic granules for continuous-flow reactors: Precipitating calcium and iron salts in granular interiors.

    Science.gov (United States)

    Juang, Yu-Chuan; Sunil S, Adav; Lee, Duu-Jong; Tay, Joo-Hwa

    2010-11-01

    Aerobic sludge granules are compact, strong microbial aggregates that have excellent settling ability and capability to efficiently treat high-strength and toxic wastewaters. The aerobic granules cultivated with low ammonium and phosphates lost structural stability within 3 days in continuous-flow reactors. Conversely, stable aerobic granules were cultivated in substrate with high levels of ammonium salts that could stably exist for 216 days in continuous-flow reactors with or without submerged membrane. The scanning electron microscopy, energy dispersive spectroscopy microanalysis and the confocal laser scanning microscopy imaging detected large amounts of calcium and iron precipitates in granule interiors. The Visual MINTEQ version 2.61 calculation showed that the phosphates and hydroxides were the main species in the precipitate.

  14. Effect of Calcium Aluminate Cement Variety on the Hydration of Portland Cement in Blended System

    Institute of Scientific and Technical Information of China (English)

    XU Linglin; WANG Peiming; Geert DE SCHUTTER; WU Guangming

    2014-01-01

    Two kinds of CACs with different monocalcium aluminate (CA) contents were used in the PC/CAC (PAC) mixtures. Effects of CA and CACs on the properties of PAC were analyzed by setting times and the compressive strength tests, and also by means of calorimetry, XRD, DTA-TG and ESEM. The experimental results show that the compressive strength of the PAC mortars decreases with increasing content of CAC while it declines sharply with a higher content of CA in CAC. Compared with neat PC paste, the content of calcium hydroxide in hydrates of PAC paste decreases significantly, and the hydration time of PC is prominently prolonged. Additionally, the higher the content of CA in CAC, the more obviously the hydration of PC is delayed, confirming that the CA phase in CAC plays an important role in the delay of PC hydration.

  15. Influence of portland cement replacement in high calcium fly ash geopolymer paste

    Directory of Open Access Journals (Sweden)

    Tanakorn Phoo-ngernkham

    2014-03-01

    Full Text Available This article presents the influence of ordinary Portland cement (OPC replacement in high calcium fly ash (FA geopolymer paste. FA was used to replace OPC at the rate of 5, 10 and 15% by mass of binder. Sodium silicate (Na2SiO3 and 10 molar sodium hydroxide (NaOH solutions were used as the alkaline solution in the reaction. The Na2SiO3/NaOH ratio of 2.0 and the liquid/binder (L/B ratio of 0.60 were used in all mixtures. The results of increase OPC replacement, the setting time and compressive strain capacity decreased while the compressive strength and modulus of elasticity increased. The compressive strength and modulus of elasticity at 28 days of geopolymer pastes with 15% OPC replacement were 36.7 MPa and 13,300 MPa, respectively.

  16. Calcium Orthophosphate-Based Bioceramics

    Directory of Open Access Journals (Sweden)

    Sergey V. Dorozhkin

    2013-09-01

    Full Text Available Various types of grafts have been traditionally used to restore damaged bones. In the late 1960s, a strong interest was raised in studying ceramics as potential bone grafts due to their biomechanical properties. A bit later, such synthetic biomaterials were called bioceramics. In principle, bioceramics can be prepared from diverse materials but this review is limited to calcium orthophosphate-based formulations only, which possess the specific advantages due to the chemical similarity to mammalian bones and teeth. During the past 40 years, there have been a number of important achievements in this field. Namely, after the initial development of bioceramics that was just tolerated in the physiological environment, an emphasis was shifted towards the formulations able to form direct chemical bonds with the adjacent bones. Afterwards, by the structural and compositional controls, it became possible to choose whether the calcium orthophosphate-based implants remain biologically stable once incorporated into the skeletal structure or whether they were resorbed over time. At the turn of the millennium, a new concept of regenerative bioceramics was developed and such formulations became an integrated part of the tissue engineering approach. Now calcium orthophosphate scaffolds are designed to induce bone formation and vascularization. These scaffolds are often porous and harbor different biomolecules and/or cells. Therefore, current biomedical applications of calcium orthophosphate bioceramics include bone augmentations, artificial bone grafts, maxillofacial reconstruction, spinal fusion, periodontal disease repairs and bone fillers after tumor surgery. Perspective future applications comprise drug delivery and tissue engineering purposes because calcium orthophosphates appear to be promising carriers of growth factors, bioactive peptides and various types of cells.

  17. A strategy of precipitated calcium carbonate (CaCO{sub 3}) fillers for enhancing the mechanical properties of polypropylene polymers

    Energy Technology Data Exchange (ETDEWEB)

    Thenepalli, Thriveni; Ahn, Ji Whan [Korea Institute of Geoscience and Mineral Resources (KIGAM), Daejeon (Korea, Republic of); Ahn, Young Jun; Han, Choon [Kwangwoon University, Seoul (Korea, Republic of); Ramakrishna, Chilakala [Hanil Cement, Danyang (Korea, Republic of)

    2015-06-15

    A wide variety of fillers are currently used in more than twenty types of polymer resins, although four of them alone (polypropylene, polyamides, thermoplastic polyesters, and polyvinyl chloride) account for 90% of the market of mineral fillers in plastics. Polypropylene (PP) and PVC dominate the market for calcium carbonate. PP is a versatile reinforcement material that can meet engineering and structural specifications and is widely used for automotive components, home appliances, and industrial applications. Talc, mica, clay, kaolin, wollastonite, calcium carbonates, feldspar, aluminum hydroxide, glass fibers, and natural fibers are commonly used in fillers. Among these, calcium carbonate (both natural and synthetic) is the mos abundant and affords the possibility of improved surface finishing, control over the manufacture of products, and increased electric resistance and impact resistance. Meeting the global challenge to reduce the weight of vehicles by using plastics is a significant issue. The current the global plastic and automobile industry cannot survive without fillers, additives, and reinforcements. Polypropylene is a major component of the modern plastic industry, and currently is used in dashboards, wheel covers, and some engine parts in automobiles. This article reports that the use of calcium carbonate fillers with polypropylene is the best choice to enhance the mechanical properties of plastic parts used in automobiles.

  18. Apatite Formation from Amorphous Calcium Phosphate and Mixed Amorphous Calcium Phosphate/Amorphous Calcium Carbonate.

    Science.gov (United States)

    Ibsen, Casper J S; Chernyshov, Dmitry; Birkedal, Henrik

    2016-08-22

    Crystallization from amorphous phases is an emerging pathway for making advanced materials. Biology has made use of amorphous precursor phases for eons and used them to produce structures with remarkable properties. Herein, we show how the design of the amorphous phase greatly influences the nanocrystals formed therefrom. We investigate the transformation of mixed amorphous calcium phosphate/amorphous calcium carbonate phases into bone-like nanocrystalline apatite using in situ synchrotron X-ray diffraction and IR spectroscopy. The speciation of phosphate was controlled by pH to favor HPO4 (2-) . In a carbonate free system, the reaction produces anisotropic apatite crystallites with large aspect ratios. The first formed crystallites are highly calcium deficient and hydrogen phosphate rich, consistent with thin octacalcium phosphate (OCP)-like needles. During growth, the crystallites become increasingly stoichiometric, which indicates that the crystallites grow through addition of near-stoichiometric apatite to the OCP-like initial crystals through a process that involves either crystallite fusion/aggregation or Ostwald ripening. The mixed amorphous phases were found to be more stable against phase transformations, hence, the crystallization was inhibited. The resulting crystallites were smaller and less anisotropic. This is rationalized by the idea that a local phosphate-depletion zone formed around the growing crystal until it was surrounded by amorphous calcium carbonate, which stopped the crystallization.

  19. Adsorption characteristics of U(VI) on Fe(III)Cr(III) (oxy)hydroxides synthesized at different temperatures.

    Science.gov (United States)

    Ahn, Hyangsig; Jo, Ho Young; Lee, Young Jae; Kim, Geon-Young

    2016-07-01

    In this study, the adsorption behavior of U(VI) on (oxy)hydroxides synthesized at different temperatures (25 and 75 °C) was investigated. Four (oxy)hydroxides were synthesized by drying slurries of Fe(III) and Fe(III)Cr(III) (oxy)hydroxide in a vacuum desiccator (25 °C) or in an oven (75 °C). Batch adsorption tests were conducted using the (oxy)hydroxides thus synthesized and groundwater containing uranium ions. In general, the U(VI) removal fraction significantly increased with increasing pH from 3 to 5, remained constant with increasing pH from 5 to 9, and decreased at pH greater than 9, regardless of the type of (oxy)hydroxides and solid-to-liquid ratio. The effect of pH on the U(VI) removal fraction was more significant at a low solid-to-liquid ratio. The oven-dried Fe(III) (oxy)hydroxide exhibited a U(VI) removal fraction lower than that of the vacuum-dried one, whereas the oven-dried Fe(III)Cr(III) (oxy)hydroxide exhibited a U(VI) removal fraction higher than that exhibited by the vacuum-dried one. X-ray photoelectron spectroscopy (XPS) analysis results indicated that the difference in the U(VI) removal fraction is attributed to the dissolution and precipitation of the Fe(III) (oxy)hydroxide during oven drying and dehydration of the Fe(III)Cr(III) (oxy)hydroxide during oven drying.

  20. 采用ICP-AES测定高纯氢氧化钠中Ca、Al、Si的含量%Using ICP-AES to determine the concentration of Ca, Al and Si in high-purity sodium hydroxide

    Institute of Scientific and Technical Information of China (English)

    丁珺

    2012-01-01

    介绍了等离子体原子发射光谱,采用标准加入法测定高纯氢氧化钠中痕量Ca、Al、Si含量的方法,该方法的准确度和精密度都符合定量要求。目前,该方法已应用于高纯氢氧化钠中杂质氧化钙、氧化铝、氧化硅含量的测定,且具有操作简便、省时、省材和高灵敏度等特点,适用于批量样品的测定。%This report introduces a novel method to determine the concentration of trace impurities in high- purity sodium hydroxide. The method uses ICP-AES combined with standard addition, thus its accuracy and precision fits the requirement of quantitative measurement. This method has been successfully applied to determine the concentration of calcium oxide (CaO), aluminum oxide (A1203) and silicon dioxide (SiO2) in high-purity sodium hydroxide. The method is not only convenient, fast but also very sensitive, therefore is suitable for batch analysis.

  1. Fabrication of functional transition metal oxide and hydroxide used as catalysts and battery materials

    Science.gov (United States)

    Xu, Linping

    My research is focused on developing metal oxide and hydroxide nanomaterials which can be used as battery materials, organic transformation catalysts, and photocatalysts. This research involves studying ZnO with different morphologies as photocatalysts for phenol degradation, producing CuO as olefin epoxidation catalysts, developing V and Cu incorporated manganese oxides as cathode materials for Li-ion batteries, and fabricating alpha-nickel hydroxide for Li-air battery materials. The first part includes producing ZnO as a photocatalyst for phenol degradation. The goal of this study is the synthesis of ZnO with different morphologies using the solvothermal method. The influence of solvents has been studied in detail. Their properties and photocatalytic performances have been explored as well. The second part of the research is concerned with developing novel urchin-like CuO as an olefin epoxidation catalyst. The purpose of this study is to develop a new catalyst, CuO, for olefin epoxidation. The copper source and precipitators were optimized, and the possible self-assembly mechanism of the urchin-like morphology was proposed. The catalytic activity of CuO for olefin epoxidation was studied. The third part of this work includes developing V, Cu incorporated manganese oxide (V-Cu-OMS-2) as cathode materials for Li-ion batteries. The purpose of this project is to develop a new material with enhanced battery performance. V and Cu incorporated manganese oxide were developed using hydrothermal methods. Octahedral molecular sieve (OMS) materials show mixed valences of Mn 3+ and Mn4+, which produces novel properties in battery applications. Inexpensive starting materials make OMS materials more promising for commercial applications. How the incorporation of V and Cu affected OMS-2 materials was investigated in terms of their crystal structure, morphologies, and surface areas. The battery performance of the incorporated OMS-2 materials with different loading amounts of V

  2. Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

    Energy Technology Data Exchange (ETDEWEB)

    Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E., E-mail: gantipas@metal.ntua.gr

    2014-01-15

    Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH){sub 3}·3H{sub 2}O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH){sub 3}(am) was stable with a solubility lower than 50 μg/l in the range 5.7 < pH < 11. • For mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3}, the stability region was extended to 4.8 < pH < 13.5. -- Abstract: Chromium is a common contaminant of soils and aquifers and constitutes a major environmental problem. In nature, chromium usually exists in the form of two oxidation states, trivalent, Cr(III), which is relatively innocuous for biota and for the aquatic environment, and hexavalent, Cr(VI) which is toxic, carcinogenic and very soluble. Accordingly, the majority of wastewater and groundwater treatment technologies, include a stage where Cr(VI) is reduced to Cr(III), in order to remove chromium from the aqueous phase and bind the element in the form of environmentally stable solid compounds. In the absence of iron the final product is typically of the form Cr(OH){sub 3}·xH{sub 2}O whereas in the presence of iron the precipitate is a mixed Fe{sub (1−x)}Cr{sub x}(OH){sub 3} phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe{sub x},Cr{sub 1−x})(OH){sub 3} hydroxides as compared to the stability of Cr(OH){sub 3}. We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH){sub 3}·3H{sub 2}O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH){sub 3}(am) phase. Mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3} hydroxides were found to be of the ferrihydrite structure, Fe(OH){sub 3}, and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe

  3. Presynaptic calcium signalling in cerebellar mossy fibres

    DEFF Research Database (Denmark)

    Thomsen, Louiza Bohn; Jörntell, Henrik; Midtgaard, Jens

    2010-01-01

    Whole-cell recordings were obtained from mossy fibre terminals in adult turtles in order to characterize the basic membrane properties. Calcium imaging of presynaptic calcium signals was carried out in order to analyse calcium dynamics and presynaptic GABA B inhibition. A tetrodotoxin (TTX....... Calcium imaging using Calcium-Green dextran revealed a stimulus-evoked all-or-none TTX-sensitive calcium signal in simple and complex rosettes. All compartments of a complex rosette were activated during electrical activation of the mossy fibre, while individual simple and complex rosettes along an axon......)-sensitive fast Na(+) spike faithfully followed repetitive depolarizing pulses with little change in spike duration or amplitude, while a strong outward rectification dominated responses to long-lasting depolarizations. High-threshold calcium spikes were uncovered following addition of potassium channel blockers...

  4. Calcium regulation in endosymbiotic organelles of plants.

    Science.gov (United States)

    Bussemer, Johanna; Vothknecht, Ute C; Chigri, Fatima

    2009-09-01

    In plant cells calcium-dependent signaling pathways are involved in a large array of biological processes in response to hormones, biotic/abiotic stress signals and a variety of developmental cues. This is generally achieved through binding of calcium to diverse calcium-sensing proteins, which subsequently control downstream events by activating or inhibiting biochemical reactions. Regulation by calcium is considered as a eukaryotic trait and has not been described for prokaryotes. Nevertheless, there is increasing evidence indicating that organelles of prokaryotic origin, such as chloroplasts and mitochondria, are integrated into the calcium-signaling network of the cell. An important transducer of calcium in these organelles appears to be calmodulin. In this review we want to give an overview over present data showing that endosymbiotic organelles harbour calcium-dependent biological processes with a focus on calmodulin-regulation.

  5. Store-operated calcium signaling in neutrophils.

    Science.gov (United States)

    Clemens, Regina A; Lowell, Clifford A

    2015-10-01

    Calcium signals in neutrophils are initiated by a variety of cell-surface receptors, including formyl peptide and other GPCRs, FcRs, and integrins. The predominant pathway by which calcium enters immune cells is termed SOCE, whereby plasma membrane CRAC channels allow influx of extracellular calcium into the cytoplasm when intracellular ER stores are depleted. The identification of 2 key families of SOCE regulators, STIM calcium "sensors" and ORAI calcium channels, has allowed for genetic manipulation of SOCE pathways and provided valuable insight into the molecular mechanism of calcium signaling in immune cells, including neutrophils. This review focuses on our current knowledge of the molecules involved in neutrophil SOCE and how study of these molecules has further informed our understanding of the role of calcium signaling in neutrophil activation.

  6. Drosophila mushroom body Kenyon cells generate spontaneous calcium transients mediated by PLTX-sensitive calcium channels.

    Science.gov (United States)

    Jiang, Shaojuan Amy; Campusano, Jorge M; Su, Hailing; O'Dowd, Diane K

    2005-07-01

    Spontaneous calcium oscillations in mushroom bodies of late stage pupal and adult Drosophila brains have been implicated in memory consolidation during olfactory associative learning. This study explores the cellular mechanisms regulating calcium dynamics in Kenyon cells, principal neurons in mushroom bodies. Fura-2 imaging shows that Kenyon cells cultured from late stage Drosophila pupae generate spontaneous calcium transients in a cell autonomous fashion, at a frequency similar to calcium oscillations in vivo (10-20/h). The expression of calcium transients is up regulated during pupal development. Although the ability to generate transients is a property intrinsic to Kenyon cells, transients can be modulated by bath application of nicotine and GABA. Calcium transients are blocked, and baseline calcium levels reduced, by removal of external calcium, addition of cobalt, or addition of Plectreurys toxin (PLTX), an insect-specific calcium channel antagonist. Transients do not require calcium release from intracellular stores. Whole cell recordings reveal that the majority of voltage-gated calcium channels in Kenyon cells are PLTX-sensitive. Together these data show that influx of calcium through PLTX-sensitive voltage-gated calcium channels mediates spontaneous calcium transients and regulates basal calcium levels in cultured Kenyon cells. The data also suggest that these calcium transients represent cellular events underlying calcium oscillations in the intact mushroom bodies. However, spontaneous calcium transients are not unique to Kenyon cells as they are present in approximately 60% of all cultured central brain neurons. This suggests the calcium transients play a more general role in maturation or function of adult brain neurons.

  7. Synthesis of the refined calcium phosphate for bone china porcelain from oyster shell

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Y.H. [Department of Environmental Engineering, Kumsung Environment College (Korea, Republic of); Chang, Pok-Ki; Lim, Yong-Mu [Department of Inorganic Materials Engineering, Chonnam National University, Kwangju (Korea, Republic of)

    1997-11-01

    In this study, the oyster shell was calcined at high temperature (>800 deg. C) in reducing atmosphere to remove impurities, refined by elutriation and magnetic separator and reacted with phosphate to synthesized di-calcium phosphate(DCP). Studies for characteristic and application to bone china porcelain of this synthesized DCP were done. By thermal and ICP analysis, the oyster shell was composed of the calcium carbonate(CaCO{sub 3}) with impurities less than 2 wt%. Fe{sub 2}O{sub 3}, TiO{sub 2} and MnO belonged to colouring material and its contents were 0.17, 0.04 and 0.02 wt%, respectively. To research reducing behavior of colouring materials Fe{sub 2}/O{sub 3} was calcined at various temperature in reducing atmosphere. Metal Fe content increased with increasing calcining temperature. After pass through magnetic separator, contents of colouring material were reduced Fe{sub 2}O{sub 3} to 0.07, TiO{sub 2} to 0.03 and MnO to 0.01 wt%, respectively. Di-calcium phosphate synthesized from calcium-hydroxide based upon oyster shell and phosphate in ph=3.5 showed crystalline phase of brushite type, and changed to {Upsilon}-Ca{sub 2}P{sub 2}O{sub 7} at 450 deg. C. For DCP calcined at 1200.deg. C, average particle size was 3.56{mu}m, specific surface area was 1.6851 m{sup 2}/g and had no agglomerate. For bone china used the synthesized DCP, the high temperature slump was 7.5 mm, the shrinkage was 13.7% and the whiteness was 95.26% similarly situated with that of H company. (author). 18 refs., 9 figs., 4 tabs.

  8. Calcium channel antagonists in hypertension.

    Science.gov (United States)

    Ambrosioni, E; Borghi, C

    1989-02-01

    The clinical usefulness of calcium entry-blockers for the treatment of high blood pressure is related to their capacity to act upon the primary hemodynamic derangement in hypertension: the increased peripheral vascular resistance. They can be used alone or in combination with other antihypertensive agents for the treatment of various forms of hypertensive disease. The calcium entry-blockers appear to be the most useful agents for the treatment of hypertension in the elderly and for the treatment of hypertension associated with ischemic heart disease, pulmonary obstructive disease, peripheral vascular disease, and supraventricular arrhythmias. They are effective in reducing blood pressure in pregnancy-associated hypertension and must be considered as first-line therapy for the treatment of hypertensive crisis.

  9. The calcium-alkali syndrome

    OpenAIRE

    Arroyo, Mariangeli; Fenves, Andrew Z.; Emmett, Michael

    2013-01-01

    The milk-alkali syndrome was a common cause of hypercalcemia, metabolic alkalosis, and renal failure in the early 20th century. It was caused by the ingestion of large quantities of milk and absorbable alkali to treat peptic ulcer disease. The syndrome virtually vanished after introduction of histamine-2 blockers and proton pump inhibitors. More recently, a similar condition called the calcium-alkali syndrome has emerged as a common cause of hypercalcemia and alkalosis. It is usually caused b...

  10. Calcium phosphate polymer hybrid materials

    OpenAIRE

    2011-01-01

    Calcium phosphate (CaP) is of strong interest to the medical field because of its potential for bone repair, gene transfection, etc.1-3 Nowadays, the majority of the commercially available materials are fabricated via “classical” materials science approaches, i.e. via high temperature or high pressure approaches, from rather poorly defined slurries, or from organic solvents.3,4 Precipitation of inorganics with (polymeric) additives from aqueous solution on the other hand enables the synthesis...

  11. CCN3 and calcium signaling

    Directory of Open Access Journals (Sweden)

    Li Chang Long

    2003-08-01

    Full Text Available Abstract The CCN family of genes consists presently of six members in human (CCN1-6 also known as Cyr61 (Cystein rich 61, CTGF (Connective Tissue Growth Factor, NOV (Nephroblastoma Overexpressed gene, WISP-1, 2 and 3 (Wnt-1 Induced Secreted Proteins. Results obtained over the past decade have indicated that CCN proteins are matricellular proteins, which are involved in the regulation of various cellular functions, such as proliferation, differentiation, survival, adhesion and migration. The CCN proteins have recently emerged as regulatory factors involved in both internal and external cell signaling. CCN3 was reported to physically interact with fibulin-1C, integrins, Notch and S100A4. Considering that, the conformation and biological activity of these proteins are dependent upon calcium binding, we hypothesized that CCN3 might be involved in signaling pathways mediated by calcium ions. In this article, we review the data showing that CCN3 regulates the levels of intracellular calcium and discuss potential models that may account for the biological effects of CCN3.

  12. Store-Operated Calcium Channels.

    Science.gov (United States)

    Prakriya, Murali; Lewis, Richard S

    2015-10-01

    Store-operated calcium channels (SOCs) are a major pathway for calcium signaling in virtually all metozoan cells and serve a wide variety of functions ranging from gene expression, motility, and secretion to tissue and organ development and the immune response. SOCs are activated by the depletion of Ca(2+) from the endoplasmic reticulum (ER), triggered physiologically through stimulation of a diverse set of surface receptors. Over 15 years after the first characterization of SOCs through electrophysiology, the identification of the STIM proteins as ER Ca(2+) sensors and the Orai proteins as store-operated channels has enabled rapid progress in understanding the unique mechanism of store-operate calcium entry (SOCE). Depletion of Ca(2+) from the ER causes STIM to accumulate at ER-plasma membrane (PM) junctions where it traps and activates Orai channels diffusing in the closely apposed PM. Mutagenesis studies combined with recent structural insights about STIM and Orai proteins are now beginning to reveal the molecular underpinnings of these choreographic events. This review describes the major experimental advances underlying our current understanding of how ER Ca(2+) depletion is coupled to the activation of SOCs. Particular emphasis is placed on the molecular mechanisms of STIM and Orai activation, Orai channel properties, modulation of STIM and Orai function, pharmacological inhibitors of SOCE, and the functions of STIM and Orai in physiology and disease.

  13. Kinetics of calcium sulfoaluminate formation from tricalcium aluminate, calcium sulfate and calcium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xuerun, E-mail: xuerunli@163.com; Zhang, Yu; Shen, Xiaodong, E-mail: xdshen@njut.edu.cn; Wang, Qianqian; Pan, Zhigang

    2014-01-15

    The formation kinetics of tricalcium aluminate (C{sub 3}A) and calcium sulfate yielding calcium sulfoaluminate (C{sub 4}A{sub 3}$) and the decomposition kinetics of calcium sulfoaluminate were investigated by sintering a mixture of synthetic C{sub 3}A and gypsum. The quantitative analysis of the phase composition was performed by X-ray powder diffraction analysis using the Rietveld method. The results showed that the formation reaction 3Ca{sub 3}Al{sub 2}O{sub 6} + CaSO{sub 4} → Ca{sub 4}Al{sub 6}O{sub 12}(SO{sub 4}) + 6CaO was the primary reaction < 1350 °C with and activation energy of 231 ± 42 kJ/mol; while the decomposition reaction 2Ca{sub 4}Al{sub 6}O{sub 12}(SO{sub 4}) + 10CaO → 6Ca{sub 3}Al{sub 2}O{sub 6} + 2SO{sub 2} ↑ + O{sub 2} ↑ primarily occurred beyond 1350 °C with an activation energy of 792 ± 64 kJ/mol. The optimal formation region for C{sub 4}A{sub 3}$ was from 1150 °C to 1350 °C and from 6 h to 1 h, which could provide useful information on the formation of C{sub 4}A{sub 3}$ containing clinkers. The Jander diffusion model was feasible for the formation and decomposition of calcium sulfoaluminate. Ca{sup 2+} and SO{sub 4}{sup 2−} were the diffusive species in both the formation and decomposition reactions. -- Highlights: •Formation and decomposition of calcium sulphoaluminate were studied. •Decomposition of calcium sulphoaluminate combined CaO and yielded C{sub 3}A. •Activation energy for formation was 231 ± 42 kJ/mol. •Activation energy for decomposition was 792 ± 64 kJ/mol. •Both the formation and decomposition were controlled by diffusion.

  14. Dynamics of Intercalation/De-Intercalation of Rhodamine B during the Polymorphic Transformation of CdAl Layered Double Hydroxide to the Brucite-Like Cadmium Hydroxide

    KAUST Repository

    Saliba, Daniel

    2016-06-23

    Cadmium-Aluminum layered double hydroxide (CdAl LDH) is thermodynamically unstable and transforms to Cd(OH)2 and Al(OH)3 in a short period of time. We present a reaction-diffusion framework that enables us to use in situ steady-state fluorescence spectroscopy to study the kinetics of intercalation of a fluorescent probe (Rhodamine B (RhB)) during the formation of the CdAl LDH and its de-intercalation upon the conversion of the LDH phase to the β phase (Cd(OH)2). The method involves the diffusion of sodium hydroxide into a hydrogel gel matrix containing the aluminum and cadmium ions as well as the species we wish to incorporate in the interlayers of the LDH. The existence of RhB between the LDH layers and its expel during the transition into the β phase are proved via fluorescence microscopy, XRD and ssNMR. The activation energies of intercalation and de-intercalation of RhB are computed and show dependence on the cationic ratio of the corresponding LDH. We find that the energies of de- intercalation are systematically higher than those of intercalation proving that the dyes are stabilized due to the probe-brucite sheets interactions.

  15. Cementing properties of steel slag activated by sodium silicates and sodium hydroxide

    Institute of Scientific and Technical Information of China (English)

    Wen Ni; En Wang; Jianping Li; Han Sun

    2005-01-01

    Steel slag which is mainly composed of γ-CasSiO4 and other silicates or alumino-silicates is activated by sodium silicates and sodium hydroxide. The powders of such steel slag are usually inert to hydrate and subsequently have very low ability of cementing. But when sodium silicates and sodium hydroxide are used as activators the steel slag shows very good properties of cementing. When activated with NaOH solution the hardened slurry of the steel slag has a compressive strength of 11.13 MPa after being cured for 28 days. When activated with Na2SiO3 solution the samples after being cured for 28 days have an average compressive strength of 40.23 MPa. While the steel slag slurry which is only mixed with water has a compressive of 0.88 MPa after being cured for 28 days.

  16. Synthesis and carbon dioxide sorption of layered double hydroxide/silica foam nanocomposites with hierarchical mesostructure

    KAUST Repository

    Fu, Liling

    2014-03-05

    Layered double hydroxides (LDHs) with a hierarchical mesostructure are successfully synthesized on mesoporous silica foams by simple impregnation and hydrothermal treatment. The as-synthesized LDH/silica foam nanocomposites show well-defined mesostructures with high surface areas, large pore volumes, and mesopores of 6-7 nm. The nanocomposites act as carbon dioxide (CO2) sorbents under simulated flue gas conditions. They also exhibit significantly enhanced CO2 capacities under high-pressure conditions and high CO2/N2 and CO2/CH4 selectivities. Respect the hierarchy: Hierarchical mesoporous layered double hydroxide (LDH) nanocomposites with high surface areas and large pore volumes are synthesized by controlled hydrothermal growth of LDH precursors on a mesoporous silica foam. The as-synthesized nanocomposites exhibit a significantly enhanced capacity and selectivity towards carbon dioxide, making them very promising candidates for carbon dioxide (CO2) separation applications. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Cadmium-Aluminum Layered Double Hydroxide Microspheres for Photocatalytic CO2Reduction

    KAUST Repository

    Saliba, Daniel

    2016-03-30

    We report the synthesis of cadmium-aluminum layered double hydroxide (CdAl LDH) using the reaction-diffusion framework. As the hydroxide anions diffuse into an agar gel matrix containing the mixture of aluminum and cadmium salts at a given ratio, they react to give the LDH. The LDH self-assembles inside the pores of the gel matrix into a unique spherical-porous shaped microstructure. The internal and external morphologies of the particles are studied by electron microscopy and tomography revealing interconnected channels and a high surface area. This material is shown to exhibit a promising performance in the photoreduction of carbon dioxide using solar light. Moreover, the palladium-decorated version shows a significant improvement in its reduction potential at room temperature. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Interaction of pristine hydrotalcite-like layered double hydroxides with CO2: a thermogravimetric study

    Indian Academy of Sciences (India)

    Shivanna Marappa; P Vishnu Kamath

    2015-12-01

    Metal oxides in general have surface acidic sites, but for exceptional circumstances, are not expected to mineralize CO2. Given their intrinsic basicity and an expandable interlayer gallery, the hydrotalcite-like layered double hydroxides (LDHs) are expected to be superior candidate materials for CO2 mineralization. However, the incorporation of Al3+ adversely impacts the ability of the metal hydroxide layer to interact with CO2 in the gas phase in comparison with the unitary Mg(OH)2. Thermogravimetric analysis shows that the decomposition reaction of the [Mg–Al–CO3] LDH is only marginally delayed in flowing CO2 in comparison with flowing N2, showing only an apparent marginal CO2 uptake. Al3+ ion severely attenuates the surface basicity of the LDHs, as the unitary Al(OH)3 is acidic in comparison with Mg(OH)2 and shows little or no interaction with CO2 in the gas phase.

  19. Inclusion of poly-aromatic hydrocarbon (PAH) molecules in a functionalized layered double hydroxide

    Indian Academy of Sciences (India)

    L Mohanambe; S Vasudevan

    2006-01-01

    The internal surface of an Mg-Al layered double hydroxide has been functionalized by anchoring carboxy-methyl derivatized -cyclodextrin cavities to the gallery walls. Neutral polyaromatic hydrocarbon (PAH) molecules have been included within the functionalized solid by driving the hydrophobic aromatic molecules from a polar solvent into the less polar interior of the anchored cyclodextrin cavities by a partitioning process. The optical (absorption and emission) properties of the PAH molecules included within the functionalized Mg-Al layered double hydroxide solid are similar to that of dilute solutions of the PAH in non-polar solvents. The unique feature of these hybrid materials is that they are thermally stable over a wide temperature range with their emission properties practically unaltered.

  20. Cadmium-Aluminum Layered Double Hydroxide Microspheres for Photocatalytic CO2 Reduction.

    Science.gov (United States)

    Saliba, Daniel; Ezzeddine, Alaa; Sougrat, Rachid; Khashab, Niveen M; Hmadeh, Mohamad; Al-Ghoul, Mazen

    2016-04-21

    We report the synthesis of cadmium-aluminum layered double hydroxide (CdAl LDH) using the reaction-diffusion framework. As the hydroxide anions diffuse into an agar gel matrix containing the mixture of aluminum and cadmium salts at a given ratio, they react to give the LDH. The LDH self-assembles inside the pores of the gel matrix into a unique spherical-porous shaped microstructure. The internal and external morphologies of the particles are studied by electron microscopy and tomography revealing interconnected channels and a high surface area. This material is shown to exhibit a promising performance in the photoreduction of carbon dioxide using solar light. Moreover, the palladium-decorated version shows a significant improvement in its reduction potential at room temperature.