Review of high burn-up RIA and LOCA database and criteria

International Nuclear Information System (INIS)

Vitanza, C.; Hrehor, M.

2006-01-01

This document is intended to provide regulators, their technical support organizations and industry with a concise review of existing fuel experimental data at RIA and LOCA conditions and considerations on how these data affect fuel safety criteria at increasing burn-up. It mostly addresses experimental results relevant to BWR and PWR fuel and it encompasses several contributions from the various experts that participated in the CSNI SEGFSM activities. It also covers the information presented at the joint CSNI/CNRA Topical Discussion on high burn-up fuel issues that took place on this subject in December 2004. The report is organized in the following way: the CABRI RIA database (14 tests), the NSRR database (26 tests) and other databases, RIA failure thresholds, comparison of failure thresholds for the HZP case, LOCA database ductility tests and quench tests, LOCA safety limit, provisional burn-up dependent criterion for Zr-4. The conclusions are as follows. On RIA, there is a well-established testing method and a significant and relatively consistent database from NSRR and Cabri tests, especially on high burn-up Zr-2 and Zr-4 cladding. It is encouraging that several correlations have been proposed for the RIA fuel failure threshold. Their predictions are compared and discussed in this paper for a representative PWR case. On LOCA, there are two different test methods, one based on ductility determinations and the other based on 'integral' quench tests. The LOCA database at high burn-up is limited to both testing methods. Ductility tests carried out with pre-hydrided non-irradiated cladding show a pronounced hydrogen effect. Data for actual high burn-up specimens are being gathered in various laboratories and will form the basis for a burn-up dependent LOCA limit. A provisional burn-up dependent criterion is discussed in the paper

Reactivity feedback evaluation of material relocations in the CABRI-1 experiments with fuel worth distributions from SNR-300

International Nuclear Information System (INIS)

Royl, P.; Pfrang, W.; Struwe, D.

1991-01-01

The fuel relocations from the CABRI-1 experiments with irradiated fuel that had been evaluated from the hodoscope measurements were used together with fuel reactivity worth distributions from the SNR-300 to estimate the reactivity effect which these motions would have if they occurred in SNR-300 at the same relative distance to the peak power as in CABRI. The procedure for the reactivity evaluation is outlined including the assumptions made for fuel mass conservation. The results show that the initial fuel motion yields always negative reactivities. They also document the mechanism for a temporary reactivity increase by in-pin fuel flow in some transient overpower tests. This mechanism, however, never dominates, because material accumulates always sufficiently above the peak power point. Thus, the late autocatalytic amplifications of voiding induced power excursions by compactive in-pin fuel flow, that had been simulated in bounding loss of flow analyses for SNR-300, have no basis at all when considering the results from the CABRI-1 experiments

Mechanical energy release in CABRI-2 experiments with Viggen-4 fuel pins

International Nuclear Information System (INIS)

Wolff, J.

1993-07-01

The results of mechanical energy release evaluations in CABRI-2 experiments with Viggen-4 fuel pins (12 atom % burnup) are described. In general the experience gained by the CABRI-1 experiments is confirmed. Those physical phenomena are enhanced which are influenced by the release of fission products. Especially the late blow-out of pressurized fission gases from the lower test pin plenum led to large flow variations. The corresponding mechanical power releases are low

Assessment of the 3He pressure inside the CABRI transient rods - Development of a surrogate model based on measurements and complementary CFD calculations

Science.gov (United States)

Clamens, Olivier; Lecerf, Johann; Hudelot, Jean-Pascal; Duc, Bertrand; Cadiou, Thierry; Blaise, Patrick; Biard, Bruno

2018-01-01

CABRI is an experimental pulse reactor, funded by the French Nuclear Safety and Radioprotection Institute (IRSN) and operated by CEA at the Cadarache research center. It is designed to study fuel behavior under RIA conditions. In order to produce the power transients, reactivity is injected by depressurization of a neutron absorber (3He) situated in transient rods inside the reactor core. The shapes of power transients depend on the total amount of reactivity injected and on the injection speed. The injected reactivity can be calculated by conversion of the 3He gas density into units of reactivity. So, it is of upmost importance to properly master gas density evolution in transient rods during a power transient. The 3He depressurization was studied by CFD calculations and completed with measurements using pressure transducers. The CFD calculations show that the density evolution is slower than the pressure drop. Surrogate models were built based on CFD calculations and validated against preliminary tests in the CABRI transient system. Studies also show that it is harder to predict the depressurization during the power transients because of neutron/3He capture reactions that induce a gas heating. This phenomenon can be studied by a multiphysics approach based on reaction rate calculation thanks to Monte Carlo code and study the resulting heating effect with the validated CFD simulation.

Assessment of the 3He pressure inside the CABRI transient rods - Development of a surrogate model based on measurements and complementary CFD calculations

Directory of Open Access Journals (Sweden)

Clamens Olivier

2018-01-01

Full Text Available CABRI is an experimental pulse reactor, funded by the French Nuclear Safety and Radioprotection Institute (IRSN and operated by CEA at the Cadarache research center. It is designed to study fuel behavior under RIA conditions. In order to produce the power transients, reactivity is injected by depressurization of a neutron absorber (3He situated in transient rods inside the reactor core. The shapes of power transients depend on the total amount of reactivity injected and on the injection speed. The injected reactivity can be calculated by conversion of the 3He gas density into units of reactivity. So, it is of upmost importance to properly master gas density evolution in transient rods during a power transient. The 3He depressurization was studied by CFD calculations and completed with measurements using pressure transducers. The CFD calculations show that the density evolution is slower than the pressure drop. Surrogate models were built based on CFD calculations and validated against preliminary tests in the CABRI transient system. Studies also show that it is harder to predict the depressurization during the power transients because of neutron/3He capture reactions that induce a gas heating. This phenomenon can be studied by a multiphysics approach based on reaction rate calculation thanks to Monte Carlo code and study the resulting heating effect with the validated CFD simulation.

RIA testing capability of the transient reactor test facility

International Nuclear Information System (INIS)

Crawford, D.C.; Swanson, R.W.

1999-01-01

The advent of high-burnup fuel implementation in LWRs has generated international interest in high-burnup LWR fuel performance. Recent testing under simulated RIA conditions has demonstrated that certain fuel designs fail at peak fuel enthalpy values that are below existing regulatory criteria. Because many of these tests were performed with non-prototypically aggressive test conditions (i.e., with power pulse widths less than 10 msec FWHM and with non-protoypic coolant configurations), the results (although very informative) do not indisputably identify failure thresholds and fuel behavior. The capability of the TREAT facility to perform simulated RIA tests with prototypic test conditions is currently being evaluated by ANL personnel. TREAT was designed to accommodate test loops and vehicles installed for in-pile transient testing. During 40 years of TREAT operation and fuel testing and evaluation, experimenters have been able to demonstrate and determine the transient behavior of several types of fuel under a variety of test conditions. This experience led to an evolution of test methodology and techniques which can be employed to assess RIA behavior of LWR fuel. A pressurized water loop that will accommodate RIA testing of LWR and CANDU-type fuel has completed conceptual design. Preliminary calculations of transient characteristics and energy deposition into test rods during hypothetical TREAT RIA tests indicate that with the installation of a pressurized water loop, the facility is quite capable of performing prototypic RIA testing. Typical test scenarios indicate that a simulated RIA with a 72 msec FWHM pulse width and energy deposition of 1200 kJ/kg (290 cal/gm) is possible. Further control system enhancements would expand the capability to pulse widths as narrow as 40 msec. (author)

Out-of pile mechanical test: simulating reactivity initiated accident (RIA) of zircaloy-4 cladding tube

Energy Technology Data Exchange (ETDEWEB)

Lee, Myung Ho; Kim, Jun Hwan; Choi, Byoung Kwon; Jeong, Young Hwan [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

2004-07-01

The ejection or drop of a control rod in a reactivity initiated accident (RIA) causes a sudden increase in reactor power and in turn deposits a large amount of energy into the fuel. In a RIA, cladding tubes bear thermal expansion due to sudden reactivity and may fail from the resulting mechanical damage. Thus, RIA can be one of the safety margin reducers because the oxide on the tubes makes their thickness to support the load less as well as hydrides from the corrosion reduce the ductility of the tubes. In a RIA, the peak of reactor power from reactivity change is about 0.1m second and the temperature of the cladding tubes increases up to 1000 .deg. C in several seconds. Although it is hard to fully simulate the situation, several attempts to measure the change of mechanical properties under a RIA situation has done using a reduction coil, ring tension tests with high speed. This research was done to see the effect of oxide on the change of circumferential strength and ductility of Zircaloy-4 tubes in a RIA. The ring stretch tensile tests were performed with the strain rate of 1/sec and 0.01/s to simulate a transient of the cladding tube under a RIA. Since the test results of the ring tensile test are very sensitive to the lubricant, the tests were also carried out to select a suitable lubricant before the test of oxided specimens.

The reactor Cabri

International Nuclear Information System (INIS)

Ailloud, J.; Millot, J.P.

1964-01-01

It has become necessary to construct in France a reactor which would permit the investigation of the conditions of functioning of future installations, the choice, the testing and the development of safety devices to be adopted. A water reactor of a type corresponding to the latest CEA constructions in the field of laboratory or university reactors was decided upon: it appeared important to be able to evaluate the risks entailed and to study the possibilities of increasing the power, always demanded by the users; on the other hand, it is particularly interesting to clarify the phenomena of power oscillation and the risks of burn out. The work programme for CABRI will be associated with the work carried out on the American Sperts of the same type, during its construction, very useful contacts were made with the American specialists who designed the se reactors. A brief description of the reactor is given in the communication as well as the work programme for the first years with respect to the objectives up to now envisaged. Rough description of the reactor. CABRI is an open core swimming-pool reactor without any lateral protection, housed in a reinforced building with controlled leakage, in the Centre d'Etudes Nucleaires de Cadarache. It lies alone in the middle of an area whose radius is 300 meters long. Control and measurements equipment stand out on the edge of that zone. It consumes MTR fuel elements. The control-safety rods are propelled by compressed air. The maximum flow rate of cooling circuit is 1500 m 3 /h. Transient measurements are recorded in a RW330 unit. Aims and work programme. CABRI is meant for: - studies on the safety of water reactors - for the definition of the safety margins under working conditions: research of maximum power at which a swimming-pool reactor may operate with respect to a cooling accident, of local boiling effect on the nuclear behaviour of the reactor, performances of the control and safety instruments under exceptional

First analysis of AGS0, LT2 and E9 CABRI tests with the new SFR safety code ASTEC-Na

International Nuclear Information System (INIS)

Perez-Martin, Sara; Bandini, Giacomino; Matuzas, Vaidas; Buck, Michael; Girault, Nathalie

2015-01-01

Within the framework of the European JASMIN project, the ASTEC-Na code is being developed for safety analysis of severe accidents in SFR. In the first phase of validation of the ASTEC-Na fuel thermo-mechanical models three in-pile tests conducted in the CABRI experimental reactor have been selected to be analysed. We present here the preliminary results of the simulation of two Transient Over Power tests and one power ramp test (AGS0, LT2 and E9, respectively) where no pin failure occurred during the transient. We present the comparison of ASTEC-Na results against experimental data and other safety code results for the initial steady state conditions prior to the transient onset as well as for the fuel pin behaviour during the transients. (author)

Recent activities of the CABRI hodoscope

International Nuclear Information System (INIS)

Helmick, H.H.; Baumung, K.; Boehnel, K.

1982-01-01

The present status of the CABRI hodoscope capability and how it serves as a diagnostic aid in the CABRI Fast Reactor Safety Research Project at Cadarache, France, is reported. A brief description of the 51-channel-high by 3-channel-wide neutron hodoscope is given and data reduction methods are described. Calibration requirements and counting system deadtime measurement techniques are discussed. Examples are given showing the results of single fuel pin experiments where fuel pin failure occurred and subsequent fuel motion is observed. Computer-generated graphic displays show the evolution of fuel motion in time in both two- and three-dimensional perspective illustrations. Results from several experiments are presented

Programme of CABRI start-up measurements with the Zircaloy loop

International Nuclear Information System (INIS)

Kussmaul, G.; Rongier, P.

1981-06-01

After installation and operational tests of the CABRI Zircaloy loop, a start-up test programme will be carried out to determine the new coupling value between the driver core and the test pin and the reactivity dependent driver core energy release for transients from different power levels and modified injection rates. The purpose of the tests and the test programme itself are described in the report

RIA simulation tests using driver tube for ATF cladding

Energy Technology Data Exchange (ETDEWEB)

Cinbiz, Mahmut N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brown, N. R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lowden, R. R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Linton, K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, K. A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-07-01

Pellet-cladding mechanical interaction (PCMI) is a potential failure mechanism for accident-tolerant fuel (ATF) cladding candidates during a reactivity-initiated accident (RIA). This report summarizes Fiscal Year (FY) 2017 research activities that were undertaken to evaluate the PCMI-like hoop-strain-driven mechanical response of ATF cladding candidates. To achieve various RIA-like conditions, a modified-burst test (MBT) device was developed to produce different mechanical pulses. The calibration of the MBT instrument was accomplished by performing mechanical tests on unirradiated Generation-I iron-chromium-aluminum (FeCrAl) alloy samples. Shakedown tests were also conducted in both FY 2016 and FY 2017 using unirradiated hydrided ZIRLO™ tube samples. This milestone report focuses on testing of ATF materials, but the benchmark tests with hydrided ZIRLO™ tube samples are documented in a recent journal article.a For the calibration and benchmark tests, the hoop strain was monitored using strain gauges attached to the sample surface in the hoop direction. A novel digital image correlation (DIC) system composed of a single high-speed camera and an array of six mirrors was developed for the MBT instrument to better resolve the failure behavior of samples and to provide useful data for validation of high-fidelity modeling and simulation tools. The DIC system enable a 360° view of a sample’s outer surface. This feature was added to the instrument to determine the precise failure location on a sample’s surface for strain predictions. The DIC system was tested on several silicon carbide fiber/silicon carbide matrix (SiC/SiC) composite tube samples at various pressurization rates of the driver tube (which correspond to the strain rates for the samples). The hoop strains for various loading conditions were determined for the SiC/SiC composite tube samples. Future work is planned to enhance understanding of the failure behavior of the ATF cladding candidates of age

RIA Fuel Codes Benchmark - Volume 1

International Nuclear Information System (INIS)

Marchand, Olivier; Georgenthum, Vincent; Petit, Marc; Udagawa, Yutaka; Nagase, Fumihisa; Sugiyama, Tomoyuki; Arffman, Asko; Cherubini, Marco; Dostal, Martin; Klouzal, Jan; Geelhood, Kenneth; Gorzel, Andreas; Holt, Lars; Jernkvist, Lars Olof; Khvostov, Grigori; Maertens, Dietmar; Spykman, Gerold; Nakajima, Tetsuo; Nechaeva, Olga; Panka, Istvan; Rey Gayo, Jose M.; Sagrado Garcia, Inmaculada C.; Shin, An-Dong; Sonnenburg, Heinz Guenther; Umidova, Zeynab; Zhang, Jinzhao; Voglewede, John

2013-01-01

Reactivity-initiated accident (RIA) fuel rod codes have been developed for a significant period of time and they all have shown their ability to reproduce some experimental results with a certain degree of adequacy. However, they sometimes rely on different specific modelling assumptions the influence of which on the final results of the calculations is difficult to evaluate. The NEA Working Group on Fuel Safety (WGFS) is tasked with advancing the understanding of fuel safety issues by assessing the technical basis for current safety criteria and their applicability to high burnup and to new fuel designs and materials. The group aims at facilitating international convergence in this area, including the review of experimental approaches as well as the interpretation and use of experimental data relevant for safety. As a contribution to this task, WGFS conducted a RIA code benchmark based on RIA tests performed in the Nuclear Safety Research Reactor in Tokai, Japan and tests performed or planned in CABRI reactor in Cadarache, France. Emphasis was on assessment of different modelling options for RIA fuel rod codes in terms of reproducing experimental results as well as extrapolating to typical reactor conditions. This report provides a summary of the results of this task. (authors)

Students’ Spatial Ability through Open-Ended Approach Aided by Cabri 3D

Science.gov (United States)

Priatna, N.

2017-09-01

The use of computer software such as Cabri 3D for learning activities is very unlimited. Students can adjust their learning speed according to their level of ability. Open-ended approach strongly supports the use of computer software in learning, because the goal of open-ended learning is to help developing creative activities and mathematical mindset of students through problem solving simultaneously. In other words, creative activities and mathematical mindset of students should be developed as much as possible in accordance with the ability of spatial ability of each student. Spatial ability is the ability of students in constructing and representing geometry models. This study aims to determine the improvement of spatial ability of junior high school students who obtained learning with open-ended approach aided by Cabri 3D. It adopted a quasi-experimental method with the non-randomized control group pretest-posttest design and the 2×3 factorial model. The instrument of the study is spatial ability test. Based on analysis of the data, it is found that the improvement of spatial ability of students who received open-ended learning aided by Cabri 3D was greater than students who received expository learning, both as a whole and based on the categories of students’ initial mathematical ability.

Keefektifan Pembelajaran Model Quantum Teaching Berbantuan Cabri 3D Terhadap Kemampuan Pemecahan Masalah

Directory of Open Access Journals (Sweden)

E. Widiyaningsih

2013-06-01

Full Text Available Penelitian ini bertujuan untuk mengetahui keefektifan pembelajaran model Quantum Teaching berbantuan Cabri 3D terhadap kemampuan pemecahan masalah peserta didik. Populasi dalam penelitian ini adalah peserta didik kelas X SMA Negeri 11 Semarang tahun pelajaran 2012/ 2013. Ada dua kelas sampel yaitu kelas eksperimen yang diterapkan pem-belajaran matematika menggunakan model pembelajaran Quantum Teaching berbantuan Cabri 3D dan kelas kontrol yang diterapkan pembelajaran Direct Interaction(DI. Hasil menunjukkan bahwa hasil belajar peserta didik pada aspek kemampuan pemecahan masalah menggunakan model pembelajaran Quantum Teaching mencapai KKM individu dan klasikal, rata-rata hasil belajar peserta didik pada aspek kemampuan pemecahan masalah pada kelas eksperimen lebih baik dari kelas kontrol. Berdasarkan pembahasan di atas dapat disimpulkan bahwa pembelajaran menggunakan model Quantum Teaching berbantuan Cabri 3D efektif terhadap kemampuan pemecahan masalah peserta didik.   This paper purpose of this study was to determine learning using the Quantum Teaching model exploration with Cabri 3D is effective to student’s problem solving ability. The population in this study was students of grade X Eleven Senior High School of Semarang academic year 2012/2013. There were two sample classes; those were an experimental class that applied mathematics learning using the Quantum Teaching model exploration with Cabri 3D and control class that applied Direct Instruction (DI learning. The results showed that the learning outcomes of students in problem solving ability aspects using the Quantum Teaching model exploration with Cabri 3D  can achieve individual and classical mastery learning, the percentage of learning outcomes of student’s problem solving ability in experiment class  better than  learning outcomes of student’s problem solving ability in control class, the average of learning outcomes of student’s problem solving ability in experiment

Fuel pin behaviour under conditions of control rod withdrawal accident in CABRI-2 experiments

International Nuclear Information System (INIS)

Papin, Joelle; Lemoine, Francette; Sato, Ikken; Struwe, Dankward; Pfrang, Werner

1994-01-01

Simulation of the control rod withdrawal accident has been performed in the international CABRI-2 experimental programme. The tests realized with industrial pins led to clarification of the influence of the pellet design and have shown the important role of fission products on the solid fuel swelling which promotes early pin failure with solid fuel pellet. With annular pellet design, large fuel swelling combined to low smear density leads to degradation of fuel thermal conductivity and thus reduces power to melt. However, the high margin to deterministic failure is confirmed with hollow pellets. Improvements of the modelling were necessary to describe such behaviours in computer codes as SAS-4A, PAPAS-2S and PHYSURAC. (author)

Experiences of graduate students: Using Cabri as a visualization tool in math education

Directory of Open Access Journals (Sweden)

Çiğdem Gül

2014-12-01

Full Text Available Through the use of graphic calculators and dynamic software running on computers and mobile devices, students can learn complex algebraic concepts. The purpose of this study is to investigate the experiences of graduate students using Cabri as a visualization tool in math education. The qualitative case study was used in this study. Five students from graduate students studying at the non-thesis math program of a university located in the Blacksea region were the participant of the study. As a dynamic learning tool, Cabri provided participants an environment where participants visually discovered the geometry. It was concluded that dynamic learning tools like Cabri has a huge potential for teaching visually the challenging concepts that students struggle to image. Further research should investigate the potential plans for integrating the use of dynamic learning software into the math curriculum

Methods used and kind of results obtained in SCARABEE facility about fuel and clad motion diagnostics. Previsional development for SCARABEE N and CABRI facilities

International Nuclear Information System (INIS)

Bardy, J.; Manent, G.; Roche, L.; Tattegrain, A.

1975-01-01

Techniques are described for planned LMFBR loss of flow simulation studies using irradiated fuel (SCARABEE N program) and for LMFBR transient overpower studies using both fresh and irradiated fuel (CABRI program)

Transient Fuel Behavior and Failure Condition in the CABRI-2 Experiments

International Nuclear Information System (INIS)

Sato, Ikken; Lemoine, Francette; Struwe, Dankward

2004-01-01

In the CABRI-2 program, 12 tests were performed under various transient conditions covering a wide range of accident scenarios using two types of preirradiated fast breeder reactor (FBR) fuel pins with different smear densities and burnups. For each fuel, a nonfailure-transient test was performed, and it provided basic information such as fuel thermal condition, fuel swelling, and gas release. From the failure tests, information on failure mode, failure time, and axial location was obtained. Based on this information, failure conditions such as fuel enthalpy and cladding temperature were evaluated. These failure conditions were compared with the CABRI-1 tests in which different fuels as well as different transient conditions were used. This comparison, together with supporting information available from existing in-pile and out-of-pile experiments, allowed an effective understanding on failure mechanisms depending on fuel and transient conditions. It is concluded that pellet-cladding mechanical interaction (PCMI) due to fuel thermal expansion and fission-gas-induced swelling is playing an important role on mechanical clad loading especially with high smear density and low fuel-heating-rate conditions. At very high heating-rate conditions, there is no sufficient time to allow significant fuel swelling, so that cavity pressurization with fuel melting becomes the likely failure mechanism. Fuel smear density and fission-gas retention have a strong impact both on PCMI and cavity pressurization. Furthermore, pin failure is strongly dependent on cladding temperature, which plays an important role in the axial failure location. With the low smear-density fuel, considerable PCMI mitigation is possible leading to a high failure threshold as well as in-pin molten-fuel relocation along the central hole. However, even with the low smear density fuel, PCMI failure could take place with an elevated cladding-temperature condition. On the other hand, in case of a sufficiently long

The ISRN has stated on the CABRI reactor restarting

International Nuclear Information System (INIS)

2009-01-01

This paper presents the different issues examined by the ISRN (the French Institute of Radioprotection and Nuclear Safety) for the restarting of the pool type research CABRI reactor which is briefly described in appendix. These issues are: the design, realisation and monitoring of the new pressurised water test loop, the reassessment of the protection system limiting the reactivity injection during tests, inspection of fuel pencil condition, reassessment of safety studies, inspection of the condition of existing equipment which are essential for safety, reassessment of the seismic risk and of the fire risk, reassessment of operation conditions (personal radioprotection, human and organisational factors). An appendix contains the report by the Permanent Group of Experts for Nuclear Reactors with its recommendations

Interpretation of the CABRI-RAFT LTX test up to pin failure based on detailed data evaluation and PARAS-2S code analysis

International Nuclear Information System (INIS)

Fukano, Yoshitaka; Sato, Ikken

2001-09-01

The CABRI-RAFT LTX test aims at a study on the fuel-pin-failure mechanism, in-pin fuel motion and post-failure fuel relocation with an annular fuel pin which was pre-irradiated up to peak burn-up of 6.4 at%. The transient test conditions similar to those of the LT4 test were selected in the LTX test using the same type of fuel pin, allowing an effective direct comparison between the two tests. In contrast to the LT4 test which showed a large PCMI-mitigation potential of the annular fuel-pin design, early pin failure occurred in the LTX test when fuel does not seem to have molten. In order to clarify the fuel pin failure mechanism, interpretation of the LTX test up to pin failure is performed in this study, through an experimental data evaluation and a PAPAS-2S-code analysis. The PAPAS-2S code simulates reasonably the fuel thermal conditions such as transient fuel-pin heat-up and fuel melting. The present detailed data evaluation shows that the earlier cladding failure compared with the LT4 test is mainly attributed to the local cladding heat-up. Under the high-temperature condition, plenum gas pressure has a certain potential to explain the observed failure. Fuel swelling-induced PCMI does not seem significant in the LTX test and it may have contributed to the early pin failure only to a limited extent, if any. (author)

Simulation of reactivity-initiated accident transients on UO2-M5® fuel rods with ALCYONE V1.4 fuel performance code

Directory of Open Access Journals (Sweden)

Isabelle Guénot-Delahaie

2018-03-01

Full Text Available The ALCYONE multidimensional fuel performance code codeveloped by the CEA, EDF, and AREVA NP within the PLEIADES software environment models the behavior of fuel rods during irradiation in commercial pressurized water reactors (PWRs, power ramps in experimental reactors, or accidental conditions such as loss of coolant accidents or reactivity-initiated accidents (RIAs. As regards the latter case of transient in particular, ALCYONE is intended to predictively simulate the response of a fuel rod by taking account of mechanisms in a way that models the physics as closely as possible, encompassing all possible stages of the transient as well as various fuel/cladding material types and irradiation conditions of interest. On the way to complying with these objectives, ALCYONE development and validation shall include tests on PWR-UO2 fuel rods with advanced claddings such as M5® under “low pressure–low temperature” or “high pressure–high temperature” water coolant conditions.This article first presents ALCYONE V1.4 RIA-related features and modeling. It especially focuses on recent developments dedicated on the one hand to nonsteady water heat and mass transport and on the other hand to the modeling of grain boundary cracking-induced fission gas release and swelling. This article then compares some simulations of RIA transients performed on UO2-M5® fuel rods in flowing sodium or stagnant water coolant conditions to the relevant experimental results gained from tests performed in either the French CABRI or the Japanese NSRR nuclear transient reactor facilities. It shows in particular to what extent ALCYONE—starting from base irradiation conditions it itself computes—is currently able to handle both the first stage of the transient, namely the pellet-cladding mechanical interaction phase, and the second stage of the transient, should a boiling crisis occur.Areas of improvement are finally discussed with a view to simulating and

Overview on phenomena of mechanical energy release in the CABRI-experiments

International Nuclear Information System (INIS)

Wolff, J.

1989-01-01

Mechanical energy release phenomena observed in the CABRI-experiments are overviewed and discussed. Intensifying and mitigating effects are identified. They are caused by fission gases, inertia effects, pressure dissipation and fissile power

Startup measurements on the CABRI reactor

International Nuclear Information System (INIS)

Kussmaul, G.; Bensoussan, P.; Dadillon, J.; Golinelli, C.; Tonolli, J.

1979-08-01

The CABRI reactor will be used for the investigation of the behavior of fresh and irradiated fast reactor fuel pins under TOP conditions. A startup programme has been carried out to measure fundamental data determining steady state and transient behavior of the driver core as well as data ensuring safe operation of the reactor. Special emphasis was laid on quantities not well known from previous neutronics calculations, e.g. prompt-neutron generation time, Doppler feedback and time-dependent reactivity injection. Utilizing the data inferred from measurements in the dynamic code DULCINEE good agreement between calculated and observed transient behavior of the driver core has been found

Situaciones a-didácticas para la enseñanza de la homotecia utilizando CabriLM como medio

OpenAIRE

Pérez, Luis

2013-01-01

Se presenta una serie de situaciones a-didácticas, en las que los alumnos interactúan con el software CabriLM como medio, y gracias a dichas interacciones construyen conocimientos relacionados con el concepto de homotecia. El funcionamiento geométrico de los objetos de CabriLM garantiza que los fenómenos visuales corresponden a propiedades teóricas, y las posibilidades que ofrece para controlar las interacciones permiten introducir restricciones para bloquear estrategias no matemáticas para r...

Experiment data report for Test RIA 1-2 (Reactivity Initiated Accident Test Series)

International Nuclear Information System (INIS)

Zimmermann, C.L.; White, C.E.; Evans, R.P.

1979-06-01

Recorded test data are presented for the second of six planned tests in the Reactivity Initiated Accident (RIA) Test Series I, Test RIA 1-2. This test, conducted at the Power Burst Facility, had the following objectives: (1) characterize the response of preirradiated fuel rods during an RIA event conducted at boiling water reactor hot-startup conditions; and (2) evaluate the effect of rod internal pressure on preirradiated fuel rod response during an RIA event. The data from Test RIA 1-2 are graphed in engineering units and have been appraised for quality and validity. These uninterpreted data are presented for use in the nuclear fuel behavior research field before detailed analysis and interpretation have been completed

Validation of Fuel Performance Uncertainty for RIA Safety Analysis

Energy Technology Data Exchange (ETDEWEB)

Park, Nam-Gyu; Yoo, Jong-Sung; Jung, Yil-Sup [KEPCO Nuclear Fuel Co., Daejeon (Korea, Republic of)

2016-10-15

To achieve this the computer code performance has to be validated based on the experimental results. And for the uncertainty quantification, important uncertainty parameters need to be selected, and combined uncertainty has to be evaluated with an acceptable statistical treatment. And important uncertainty parameters to the rod performance such as fuel enthalpy, fission gas release, cladding hoop strain etc. were chosen through the rigorous sensitivity studies. And their validity has been assessed by utilizing the experimental results, which were tested in CABRI and NSRR. Analysis results revealed that several tested rods were not bounded within combined fuel performance uncertainty. Assessment of fuel performance with an extended fuel power uncertainty on tested rods in NSRR and CABRI has been done. Analysis results showed that several tested rods were not bounded within calculated fuel performance uncertainty. This implies that the currently considered uncertainty range of the parameters is not enough to cover the fuel performance sufficiently.

Preliminary insights of the impact of steady state uncertainties on fuel rod response to an RIA

International Nuclear Information System (INIS)

Herranz, Luis E.; Huguet, Anne

2013-01-01

Nuclear fuel cycles are driven to higher burn-ups under the nowadays more demanding operational conditions. The operational safety limits that ensure the long-term core coolability are set through the analysis of the design basis accidents, RIA scenarios. These analyses are mainly performed through computer codes that encapsulate the present understanding of fuel behavior under such events. They assess safety margins and therefore their accuracy is of utmost interest. Their predictability is extended and validated through separate effect and integral experiments data. Given the complexity of working phenomena under RIA conditions, neither existing thermo-mechanical models nor rod state characterization at the moment of power pulse reflect exactly reality. So, it is essential to know how these deviations influence code predictions. This study illustrates how uncertainties related to pre-transient rod characterization affect the estimates of nuclear fuel behavior during the transient. In order to do so, the RIA scenario of the CIP0-1 test (CABRI program) has been analyzed with FRAPCON-3 (steady state irradiation) and FRAPTRAN 1.4 (transient) codes. The input uncertainties have been propagated through the codes by following a deterministic approach. This work is framed within the CSN-CIEMAT agreement on 'Thermo-Mechanical Behavior of the Nuclear Fuel at High Burnup'. (authors)

Reactivity initiated accident test series Test RIA 1-4 fuel behavior report

International Nuclear Information System (INIS)

Cook, B.A.; Martinson, Z.R.

1984-09-01

This report presents and discusses results from the final test in the Reactivity Initiated Accident (RIA) Test Series, Test RIA 1-4, conducted in the Power Burst Facility (PBF) at the Idaho National Engineering Laboratory. Nine preirradiated fuel rods in a 3 x 3 bundle configuration were subjected to a power burst while at boiling water reactor hot-startup system conditions. The test resulted in estimated axial peak, radial average fuel enthalpies of 234 cal/g UO 2 on the center rod, 255 cal/g UO 2 on the side rods, and 277 cal/g UO 2 on the corner rods. Test RIA 1-4 was conducted to investigate fuel coolability and channel blockage within a bundle of preirradiated rods near the present enthalpy limit of 280 cal/g UO 2 established by the US Nuclear Regulatory Commission. The test design and conduct are described, and the bundle and individual rod thermal and mechanical responses are evaluated. Conclusions from this final test and the entire PBF RIA Test Series are presented

Report of blind start-up experiments carried out on the reactor Cabri between 4. and 8. July 1966

International Nuclear Information System (INIS)

Filipczak, N.; Filipczak, W.; Furet, J.; Kaiser, J.

1967-01-01

The blind start-up of a reactor without any neutronic data concerning a relatively wide range of power dynamics can be necessary when difficulties arise in the positioning of the detector or in neutron-gamma discrimination near the multiplying medium. The object of the experiments carried out on the reactor Cabri was to check the very complete analysis of the start-up accident which was studied on an analogue computer. The number of experiments carried out (12) is not sufficient to allow a definite conclusion. Nevertheless the blind start-up method advocated by N. FILIPCZAK and W. FILIPCZAK does not appear to be incompatible with the security during the operational phase (on condition that its dynamic characteristics are close to that of the reactor Cabri). (authors) [fr

Colombo cabri or vegetarian meal: wherein lies the power?

Directory of Open Access Journals (Sweden)

Meritxell Martín-i-Pardo

2006-05-01

Full Text Available “Colombo Cabri or Vegetarian Meal” montre que certains aliments sont utilisés pour définir deux sectes Hindouistes concurrentes en Guadeloupe, dans les Antilles françaises. Ces groupes expriment des identités différentes concurrentes en termes de visibilité et de revendication de pouvoir pour contrôler l’avenir de l’Hindouisme sur l’île. Ces deux entités, identifiées à juste titre comme Hindouistes « traditionalistes » d’une part et « globalistes » d’autre part, mettent en œuvre une rhétorique pour légitimer leurs différentes revendications qui passe par l’adoption ou le rejet du « colombo », un curry de viandes marinées dans cette sauce, comme repas rituel de la secte dont le discours vise à dicter le droit chemin de la communauté Hindouiste de l’île.“Colombo Cabri or Vegetarian Meal” argues that certain foods are used to configure two competing sectarian Hindu groups in Guadeloupe, French West Indies. These groups configure different identities to compete for the attention and claim effective power to control the future of Hinduism on the island. What are appropriately identified as “traditionalist” and “globalist” Hindus define a rhetoric for legitimating their different claims by appropriating or rejecting “colombo,” a curry of meats simmered in this sauce, as the ritual meal for the sect whose narrative rightly claims to define the correct path for the Hindu community on the island.

Out-of-pile test of zirconium cladding simulating reactivity initiated accident

Energy Technology Data Exchange (ETDEWEB)

Kim, J. H.; Lee, M. H.; Choi, B. K.; Bang, J. K.; Jung, Y. H. [KAERI, Taejon (Korea, Republic of)

2004-07-01

Mechanical properties of zirconium cladding such as Zircaloy-4 and advanced cladding were evaluated by ring tension test to simulate Reactivity-Initiated Accident (RIA) as an out-pile test. Cladding was hydrided by means of charging hydrogen up to 1000ppm to simulate high-burnup situation, finally fabricated to circumferential tensile specimen. Ring tension test was carried out from 0.01 to 1/sec to keep pace with actual RIA event. The results showed that mechanical strength of zirconium cladding increased at the value of 7.8% but ductility decreased at the 34% as applied strain rate and absorbed hydrogen increased. Further activities regarding out-of-pile testing plans for simulated high-burnup cladding were discussed in this paper.

The CABRI facility: Implementation of a pressurized water loop and related safety review

International Nuclear Information System (INIS)

Cabrillat, J.C.; Maegey, M.; Bourguignon, D.; Miachon, G.; Forestier, F.; Coulon, J.P.; Faury, M.

2003-01-01

The CABRI reactor operated by CEA at the CADARACHE Nuclear Center in France provided the condition for safety studies on nuclear fuel. Initially designed to support investigations on Fast Reactor fuel, large modifications are underway to provide representative conditions for studies on Light Water Fuel types. A general overview of these modifications, the related safety review and supporting studies are described in the paper. (author)

Interpretation of the CABRI-RAFT RB1 and RB2 tests through detailed data evaluation and PAPAS-2S code analysis

International Nuclear Information System (INIS)

Fukano, Yoshitaka; Sato, Ikken

2001-08-01

The CABRI-RAFT RB1 and RB2 tests were aiming at a study on impact of fuel pin failure under an overpower condition leading to fuel melting. Using a special technique, combination of through-cladding failure and fuel melting was realized. In the RB1 test, fuel ejection was prevented under a limited fuel melting condition. On the other hand, significant fuel melting was applied in the RB2 test so as to get the fuel ejection, thereby obtaining information on the fuel ejection behavior. Interpretation for these tests through the detailed experimental data evaluation and the PAPAS-2S code analysis is performed in this study. Through this study, it is indicated that molten fuel ejection can be prevented with the low smear density fuel as far as the fuel melting is not large for a slit-type cladding defect. Fuel ejection becomes possible in the case of significant fuel melting with a very thin solid fuel shell surrounding the molten fuel cavity. However, the rapidness of the fuel ejection with the low smear density fuel is less pronounced compared with that of the high smear density fuel. It is also confirmed that there is considerable DN-precursor release into the coolant flow already before fuel ejection. The result is very useful for evaluation of anomaly detection with DN signal observation. (author)

Investigation of the Development of 7th Grade Students’ Skills to Define, Construct and Classify Polygons with Cabri Geometry

Directory of Open Access Journals (Sweden)

Ahmet Yanık

2013-03-01

Full Text Available The aim of the study is to investigate the development of 7th Grade students’ skills to define, construct and classify polygons in geometry course with Cabri Geometry II Plus software geometry, an example of dynamic geometry software. The study used qualitative and quantitative research methods in accordance with the research objectives and focus, so it was designed as a mixed method research. The participants of the study were 21 7th Grade students, 11 girls and 10 boys, who were attending a secondary school in Eskişehir city center during 2012-2013 school year. As a source of qualitative data, four students in this class were selected for the interview. The data were collected with “Polygon Identification and Classification Scale”, one group pre-test and post-test in order to determine the level of development and significance level of the gender variable, and Cabri Geometry worksheets developed by the researchers. The quantitative data were analyzed with SPSS Statistics 20. Also, t-test and Wilcoxon test were used in data analysis. The data obtained from the interviews were analyzed through descriptive analysis. The qualitative data showed that the mean of correct answers given by the students to the questions in the Polygon Identification and Classification Scale was higher in the post-test than the pre-test. The ttest results for the pre-test and post-test mean scores and the results of the paired samples test showed a significant difference in favor of the post-test. There was no significant difference based on the gender variable. On the other hand, the data obtained from the interviews were coded under five different themes. The activities about the concept of formation showed that incorrect formations caused incorrect generalizations about the shapes. The study found that, as a result of the teaching practice in the study, hierarchical relations among polygons were expressed correctly. Finally, after the practice, the

Impact of fission gas on irradiated PWR fuel behaviour at extended burnup under RIA conditions

International Nuclear Information System (INIS)

Lemoine, F.; Schmitz, F.

1996-01-01

With the world-wide trend to increase the fuel burnup at discharge of the LWRs, the reliability of high burnup fuel must be proven, including its behaviour under energetic transient conditions, and in particular during RIAs. Specific aspects of irradiated fuel result from the increasing retention of gaseous and volatile fission products with burnup. The potential for swelling and transient expansion work under rapid heating conditions characterizes the high burnup fuel behaviour by comparison to fresh fuel. This effect is resulting from the steadily increasing amount of gaseous and volatile fission products retained inside the fuel structure. An attempt is presented to quantify the gas behaviour which is motivated by the results from the global tests both in CABRI and in NSRR. A coherent understanding of specific results, either transient release or post transient residual retention has been reached. The early failure of REP Na1 with consideration given to the satisfactory behaviour of the father rod of the test pin at the end of the irradiation (under load follow conditions) is to be explained both by the transient loading from gas driven fuel swelling and from the reduced clad resistance due to hydriding. (R.P.)

Experimental characterization and modelling of UO2 mechanical behaviour at high temperatures and high strain rates

International Nuclear Information System (INIS)

Salvo, Maxime

2014-01-01

The aim of this work is to characterize and model the mechanical behavior of uranium dioxide (UO 2 ) during a Reactivity Initiated Accident (RIA). The fuel loading during a RIA is characterized by high strain rates (up to 1/s) and high temperatures (1000 C - 2500 C). Two types of UO 2 pellets (commercial and high density) were therefore tested in compression with prescribed displacement rates (0.1 to 100 mm/min corresponding to strain rates of 10 -4 - 10 -1 /s) and temperatures (1100 C - 1350 C - 1550 C et 1700 C). Experimental results (geometry, yield stress and microstructure) allowed us to define a hyperbolic sine creep law and a Drucker-Prager criterion with associated plasticity, in order to model grain boundaries fragmentation at the macroscopic scale. Finite Element Simulations of these tests and of more than 200 creep tests were used to assess the model response to a wide range of temperatures (1100 C - 1700 C) and strain rates (10 -9 /s - 10 -1 /s). Finally, a constitutive law called L3F was developed for UO 2 by adding to the previous model irradiation creep and tensile macroscopic cracking. The L3F law was then introduced in the 1.5D scheme of the fuel performance code ALCYONE-RIA to simulate the REP-Na tests performed in the experimental reactor CABRI. Simulation results are in good agreement with post tests examinations. (author) [fr

El uso del Cabri en la demostracion de teoremas de la geometria euclidiana

OpenAIRE

Fuentes, Fabio; Castañez, Orlando; Gordillo, Luís; Mestre, Gelis

2009-01-01

Con el presente taller se propone utilizar el CABRI PLUS II para abordar las demostraciones de algunos teoremas de la geometría euclidiana, asociados con ángulos, triángulos y cuadriláteros, temática que es abordada en la básica primaria y secundaria, al igual que en la geometría euclidiana de la licenciatura de matemáticas de las Universidades de Colombia. La utilización de las demostraciones de teoremas es considerada una potente herramienta que ayuda a mejorar los procesos de enseñanza y d...

Experimental facilities and simulation means

International Nuclear Information System (INIS)

Thomas, J.B.

2009-01-01

This paper and its associated series of slides review the experimental facilities and the simulation means used for the development of nuclear reactors in France. These experimental facilities include installations used for the measurement and qualification of nuclear data (mainly cross-sections) like EOLE reactor and Minerve zero power reactor, installations like material testing reactors, installations dedicated to reactor safety experiments like Cabri reactor, and other installations like accelerators (Jannus accelerator, GANIL for instance) that are complementary to neutron irradiations in experimental reactors. The simulation means rely on a series of advanced computer codes: Tripoli-Apollo for neutron transport, Numodis for irradiation impact on materials, Neptune and Cathare for 2-phase fluid dynamics, Europlexus for mechanical structures, and Pleiades (with Alcyone) for nuclear fuels. (A.C.)

Pellet-Cladding Mechanical Interaction Failure Threshold for Reactivity Initiated Accidents for Pressurized Water Reactors and Boiling Water Reactors

Energy Technology Data Exchange (ETDEWEB)

Beyer, Carl E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Geelhood, Kenneth J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2013-06-01

Pacific Northwest National Laboratory (PNNL) has been requested by the U.S. Nuclear Regulatory Commission to evaluate the reactivity initiated accident (RIA) tests that have recently been performed in the Nuclear Safety Research Reactor (NSRR) and CABRI (French research reactor) on uranium dioxide (UO₂) and mixed uranium and plutonium dioxide (MOX) fuels, and to propose pellet-cladding mechanical interaction (PCMI) failure thresholds for RIA events. This report discusses how PNNL developed PCMI failure thresholds for RIA based on least squares (LSQ) regression fits to the RIA test data from cold-worked stress relief annealed (CWSRA) and recrystallized annealed (RXA) cladding alloys under pressurized water reactor (PWR) hot zero power (HZP) conditions and boiling water reactor (BWR) cold zero power (CZP) conditions.

Reactivity Initiated Accident Test Series: Test RIA 1-2. Quick look report

International Nuclear Information System (INIS)

Martinson, Z.R.; Semken, R.S.; Smith, R.H.; Osetek, D.J.

1978-12-01

The primary objectives of Test RIA 1-2 were to (a) characterize the response of preirradiated fuel rods during an RIA event conducted at boiling water reactor (BWR) hot-startup conditions for an axial peak pellet surface energy of 200 cal/g UO 2 , and (b) evaluate the effect of internal rod pressure on preirradiated fuel rod response during an RIA event. The test consisted of four, individually shrouded, pressurized water reactor-type fuel rods previously irradiated to burnups of about 4800 MWd/t. In addition to the power calibration and preconditioning, the fuel rods were subjected to a single power burst that deposited a total pellet surface energy of approximately 200 cal/gm UO 2 at the axial peak power location (estimated using the core power chambers to relate steady state and transient powers). The test data indicate that the two irradiated fuel rods prepressurized to 2.41 MPa did not fail. FRAP-T4 calculations had predicted that prompt cladding rupture would occur for pellet surface energy depositions of 206 cal/g or greater. Although the two fuel rods prepressurized to 2.41 MPa did not fail, the data indicate that at least one of the two fuel rods prepressurized to 0.1 MPa did fail. Based on the core power chamber data, this rod failure indicates a threshold for the preirradiated fuel rods near or below 200 cal/g UO 2 total pellet surface energy at the axial flux peak

Safety actuator of the Cabri reactor as a function of its power and cooling fluid flow rate

International Nuclear Information System (INIS)

Bertrand, Jean; Da Costa Vieira, David; Tattegrain, Alain

1969-04-01

This report present a device which is to provide a stop command to the Cabri reactor when the rate of its power to the cooling fluid rate reaches a value determined with respect to water temperature in the circuit. The stop command is delivered by an actuator which opens a relay contact when the power reaches a specific value. The authors present the device, its characteristics, and principle. They also present the different amplifier circuits, the input and output circuits (flow rate input, temperature input, and output circuit), the energy supply, and the various adjustments

Recent results on the RIA test in IGR reactor

International Nuclear Information System (INIS)

Asmolov, V.; Yegorova, L.

1997-01-01

At the 23d WRSM meeting the data base characterizing results of VVER high burnup fuel rods tests under reactivity-initiated accident (RIA) conditions was presented. Comparison of PWR and VVER failure thresholds was given also. Additional analysis of the obtained results was being carried out during 1996. The results of analysis show that the two different failure mechanisms were observed for PWR and VVER fuel rods. Some factors which can be as the possible reasons of these differences are presented. First of them is the state of preirradiated cladding. Published test data for PWR high burnup fuel rods demonstrated that the PWR high burnup fuel rods failed at the RIA test are characterized by very high level of oxidation and hydriding for the claddings. Corresponding researches were performed at Institute of Atomic Reactors (RLAR, Dimitrovgrad, Russia) for large set of VVER high burnup fuel rods. Results of these investigations show that preirradiated commercial Zr-1%Nb claddings practically keep their initial levels of oxidation and H 2 concentration. Consequently the VVER preirradiated cladding must keep the high level of mechanical properties. The second reason leading to differences between failure mechanisms for two types of high burnup fuel rods can be the test conditions. Now such kind of analysis have been performed by two methods

SIMULATION MODELLING OF VITÓRIA-MINAS CLOSED-LOOP RAIL NETWORK

Directory of Open Access Journals (Sweden)

Carlos Henrique Fernandes de FARIA

2015-12-01

Full Text Available This paper presents a closed loop simulation model that represents the mining logistics chain of the Vitória Minas Railway (VMR, Brazil. The simulator includes the loading process, circulation of loaded trains, unloading of ores for external and internal markets and the distribution of empty trains for new loads. General cargo and passengers trains are also included in the model, which, along with the queues formed in the circulation and the preventive and corrective maintenance of rolling stock, tracks and equipment, interfere with the transportation of iron ore. The primary objective of the iron ore transport is to meet the daily loading and unloading schedules and minimize queues by maximizing the operations at the loading and unloading points. The VMR simulator developed uses macro-mesoscopic approach with Monte Carlo simulation. To validate the simulator, we used actual data of the railway and compared with reality. We obtained a very good adhesion to the value of 2.9% for the validation scenario (Scenario 1 and 3.4% for the scenario with reducing the number of lots of wagons (Scenario 2. We concluded with this simulation that it is possible to reduce the number of GDE wagons without reducing the current level of productivity of the rail system.

Radiation Simulations for the Proposed ISOL Stations for RIA

CERN Document Server

Ronningen, Reginald; Beene, James R; Blideanu, Valetin; Boles, Jason; Bollen, Georg; Bredeweg, Todd; Bricault, Pierre; Burgess, Thomas; Carter, Ken; Conner, David L; Gabriel, Tony A; Heilbronn, Lawrence; Lawton, Don; Mansur, Louis; Mantica, Paul; Morrissey, David; Nortier, Francois M; Remec, Igor; Rennich, Mark; Reyes, Susana; Sherrill, Bradley; Stein, Werner; Stracener, Dan; Vieira, David; Wendel, Mark; Zeller, Al

2005-01-01

The Department of Energy's Office of Nuclear Physics, within the Office of Science (SC), has given high priority to consider and analyze design concepts for the target areas for the production of rare isotopes via the ISOL technique at the Rare-Isotope Accelerator (RIA) Facility. Key criteria are the maximum primary beam power of 400 kW, minimizing target change-out time, good radiological protection, flexibility with respect to implementing new target concepts, and the analysis and minimization of hazards associated with the operation of the facility. We will present examples of on-going work on simulations of radiation heating of targets, surrounding components and shielding, component activation, and levels of radiation dose, using the simulation codes MARS, MCNPX, and PHITS. These results are important to make decisions that may have a major impact on the layout, operational efficiency and cost of the facility, hazard analysis, shielding design, civil construction, component design, and material selection...

Sobre el estudio de la función cuadrática y su relación con el área de algunas figuras y su visualización usando Cabri II Plus

OpenAIRE

Vera Barrios, Dídimo

2013-01-01

Propuesta didáctica en donde se presentan algunas actividades dinámicas usando Cabri II Plus con el fin de relacionar algunos aspectos que tienen que ver con el área de algunas figuras y la función cuadrática.

Study and simulation of irradiated zirconium alloys fracture under type RIA accidental loading conditions; Comprehension et modelisation de la rupture d'alliages de zirconium irradies en conditions accidentelles de type RIA

Energy Technology Data Exchange (ETDEWEB)

Le Saux, M. [CEA Saclay, Dept. des Materiaux pour le Nucleaire (DEN/DANS/DMN/SEMI), 91 - Gif-sur-Yvette (France)

2008-07-01

The thesis aims to study and simulate the mechanical behavior under Reactivity Initiated Accident loading conditions, of the Zircaloy 4 fuel claddings, irradiated or not. It also aims to characterize and simulate the behavior and the fracture under RIA loading conditions of hydrided Zircaloy 4 non irradiated. This study proposes an experimental approach and a simulation. (A.L.B.)

Stress intensity factor at the tip of cladding incipient crack in RIA-simulating experiments for high-burnup PWR fuels

International Nuclear Information System (INIS)

Udagawa, Yutaka; Suzuki, Motoe; Sugiyama, Tomoyuki; Fuketa, Toyoshi

2009-01-01

RIA-simulating experiments for high-burnup PWR fuels have been performed in the NSRR, and the stress intensity factor K 1 at the tip of cladding incipient crack has been evaluated in order to investigate its validity as a PCMI failure threshold under RIA conditions. An incipient crack depth was determined by observation of metallographs. The maximum hydride-rim thickness in the cladding of the test fuel rod was regarded as the incipient crack depth in each test case. Hoop stress in the cladding periphery during the pulse power transient was calculated by the RANNS code. K 1 was calculated based on crack depth and hoop stress. According to the RANNS calculation, PCMI failure cases can be divided into two groups: failure in the elastic phase and failure in the plastic phase. In the former case, elastic deformation was predominant around the incipient crack at failure time. K 1 is available only in this case. In the latter, plastic deformation was predominant around the incipient crack at failure time. Failure in the elastic phase never occurred when K 1 was less than 17 MPa m 1/2 . For failure in the plastic phase, the plastic hoop strain of the cladding periphery at failure time clearly showed a tendency to decrease with incipient crack depth. The combination of K 1 , for failure in the elastic phase, and plastic hoop strain at failure, for failure in the plastic phase, can be an effective index of PCMI failure under RIA conditions. (author)

RIA Beam Dynamics Comparing TRACK to IMPACT

CERN Document Server

Mustapha, Brahim; Ostroumov, Peter; Qiang, Ji; Ryne, Robert D

2005-01-01

In order to benchmark the newly developed beam dynamics code TRACK we have performed comparisons with well established existing codes. During code development, codes like TRANSPORT, COSY, GIOS and RAYTRACE were used to check TRACK's implementation of the different beam line elements. To benchmark the end-to-end simulation of the RIA driver linac, the simulation of the low-energy part (from the ion source to the entrance of the SC linac) was compared with PARMTEQ and found to agree well. For the simulation of the SC linac the code IMPACT is used. Prior to these simulations, the code IMPACT had to be updated to meet the special requirements of the RIA driver linac. Features such as multiple charge state acceleration, stripper simulation and beam collimation were added to the code. IMPACT was also modified to support new types of rf cavities and to include fringe fields for all the elements. This paper will present a comparison of the beam dynamics simulation in the RIA driver linac between the codes TRACK and I...

Funcionalidad de Juegos de Estrategia Virtuales y del Software Cabri-géomètre II en el Aprendizaje de la Simetría en Secundaria

Directory of Open Access Journals (Sweden)

Guadalupe Rodríguez

2010-06-01

Full Text Available Presentamos resultados de un estudio exploratorio cuyo propósito es indagar sobre el uso del Cabri-Géomètre II y de un juego matemático virtual de estrategia cuando se incluyen en clases ordinarias de matemáticas de estudiantes de 12-13 años en una escuela secundaria pública de México. Para este trabajo, el tema abordado fue la simetría. El análisis de datos permitió ver la funcionalidad de estos ambientes para transformar las nociones del alumno sobre el tema y para reconocer que se puede avanzar en el desarrollo de un pensamiento matemático distinto a través de ambientes de aprendizaje computacionales. We present the results of an exploratory study whose purpose was to explore the use by 12-13 years old students of Cabri-Géomètre II and a mathematical strategic virtual game in a Mexican state school. For this paper, the mathematical focus was on symmetry. The data analysis allowed us to observe the functionality of this learning environment to transform the students’ conceptions and to recognize that a different type of mathematical thinking can be developed with these computational learning environments.

Test Review: Reynolds, C. R., & Kamphaus, R. W. (2003). "RIAS--Reynolds Intellectual Assessment Scales." Lutz, FL--Psychological Assessment Resources, Inc.

Science.gov (United States)

Dombrowski, Stefan C.; Mrazik, Martin

2008-01-01

In this article, the authors review the Reynolds Intellectual Assessment Scales (RIAS; Reynolds & Kamphaus, 2003), an individually administered test of intelligence for use with individuals between the ages of 3 and 94. The RIAS represents the newest intelligence test on the marketplace and incorporates the most current intelligence test theory…

Influence of initial conditions on rod behaviour during boiling crisis phase following a reactivity initiated accident

International Nuclear Information System (INIS)

Georgenthum, V.; Sugiyama, T.

2010-01-01

In the frame of their research programs on high burn-up fuel safety, the French Institute for Radioprotection and Nuclear Safety (IRSN) and the Japan Atomic Energy Agency (JAEA) performed a large set of tests devoted to the study of PWR fuel rod behavior during Reactivity Initiated Accident (RIA) respectively in the CABRI reactor and in the NSRR reactor. The reactor test conditions are different in terms of coolant nature, temperature and pressure. In the CABRI reactor, tests were performed until now with sodium coolant at 280 Celsius degrees and 3 bar. In the NSRR reactor most of the tests were performed with stagnant water at 20 C. degrees and atmospheric pressure but recently a new high temperature high pressure capsule has been developed which allows to performed tests at up to 280 Celsius degrees and 70 bar. The paper discusses the influence of test conditions on rod behaviour during boiling phase, based on tests results and SCANAIR code calculations. The study shows that when the boiling crisis is reached, the initial inner and outer rod pressure have an essential impact on the clad straining and possible ballooning. The analysis of the different test conditions makes it possible to discriminate the influence of initial conditions on the different phases of the transient and is useful for modelling and code development. (authors)

Researches of WWER fuel rods behaviour under RIA accident conditions

International Nuclear Information System (INIS)

Nechaeva, O.; Medvedev, A.; Novikov, V.; Salatov, A.

2003-01-01

Unirradiated fuel rod and refabricated fuel rod tests in the BIGR as well as acceptance criteria proving absence of fragmentation and the settlement modeling of refabricated fuel rods thermomechanical behavior in the BIGR-tests using RAPTA-5 code are discussed in this paper. The behaviour of WWER type simulators with E110 and E635 cladding was researched at the BIGR reactor under power pulse conditions simulating reactivity initiated accident. The results of the tests in four variants of experimental conditions are submitted. The behaviour of 12 WWER type refabricated fuel rods was researched in the BIGR reactor under power pulse conditions simulating reactivity initiated accident: burnup 48 and 60 MWd/kgU, pulse width 3 ms, peak fuel enthalpy 115-190 cal/g. The program of future tests in the research reactor MIR with high burnup fuel rod (up to 70 MWd/kgU) under conditions simulating design RIA in WWER-1000 is presented

The role of grain boundary fission gases in high burn-up fuel under reactivity initiated accident conditions

International Nuclear Information System (INIS)

Lemoine, F.; Papin, J.; Frizonnet, J.M.; Cazalis, B.; Rigat, H.

2002-01-01

In the frame of reactivity-initiated accidents (RIA) studies, the CABRI REP-Na programme is currently performed, focused on high burn-up UO 2 and MOX fuel behaviour. From 1993 to 1998, seven tests were performed with UO 2 fuel and three with MOX fuel. In all these tests, particular attention has been devoted to the role of fission gases in transient fuel behaviour and in clad loading mechanisms. From the analysis of experimental results, some basic phenomena were identified and a better understanding of the transient fission gas behaviour was obtained in relation to the fuel and clad thermo-mechanical evolution in RIA, but also to the initial state of the fuel before the transient. A high burn-up effect linked to the increasing part of grain boundary gases is clearly evidenced in the final gas release, which would also significantly contribute to the clad loading mechanisms. (authors)

Memória em idoso: relação entre percepção subjetiva e desempenho em testes objetivos

OpenAIRE

BOURSCHEID,Fábio Rodrigo; MOTHES,Luíza; IRIGARAY,Tatiana Quarti

2016-01-01

Resumo A relação entre a percepção subjetiva de memória e o desempenho em testes objetivos tem sido alvo de diversos estudos em vista de sua utilidade no diagnóstico do declínio cognitivo. Dada a ausência de consenso em relação ao tema, avaliou-se o desempenho de idosos em testes objetivos de memória, correlacionando-o com a percepção subjetiva dos participantes acerca de sua memória. Cento e cinquenta e dois idosos preencheram uma ficha de dados sociodemográficos, na qual foi incluída uma qu...

RIA type tests in ACPR

International Nuclear Information System (INIS)

Preda, Marin; Stefan, Violeta; Ancuta, Mirela; Negut, Gheorghe

2008-01-01

For a better NPP operation fuel behavior in accidental conditions (LOCA) is of great interest. Irradiation tests in ACPR can give interesting data on the CANDU fuel behavior in such kind of accidents. These data can be used for simulation, calibration and validation of fuel computer codes. The tests were accomplished in the TRIGA Annular Core Pulse Reactor (ACPR). Reactivity insertion accidents are not specific for the CANDU reactors but this type of test can contribute to a better understanding of CANDU type fuel behavior during various conditions.The tests were accomplished in the ambient pressure and temperature with fresh fuel probes. These tests gave similar results on the clad-fuel, and clad-coolant interactions which occur in LOCA accidents. The tests will be continued with instrumentation improvements what will give better statistics and information on fuel behavior in accident conditions. The structure of the paper is the following: - 1. Introduction; - 2. Irradiation device description; - 2.1. Capsule main parameters; - 2.1.1. Initial conditions; - 2.1.2. Test conditions; - 3. Tests objectives; - 4. Test of fuel; - 5. Results; - 5.1. Temperature effects; - 5.2. Pressure effects; - 6. Conclusion

Disfunção gustatória e olfatória em laringectomizados

Directory of Open Access Journals (Sweden)

Ada Salvetti Cavalcanti Caldas

2013-10-01

Full Text Available Após a cirurgia de laringectomia total, o fluxo aéreo nasal é transferido definitivamente para o traqueostoma, comprometendo a chegada de moléculas odoríferas até a cavidade nasal, podendo repercutir em alterações na percepção olfatória e gustatória nesses indivíduos. OBJETIVO: Avaliar as funções do olfato e do paladar em laringectomizados totais. Desenho do estudo: Estudo de série. MÉTODO: A amostra envolveu um grupo com 25 pacientes submetidos à laringectomia total e outro grupo de comparação com 25 pacientes não laringectomizados. A função gustatória foi avaliada por tiras gustativas de papel de filtro. Para avaliação da função olfatória, foi aplicado o teste Brief Smell Identification Test. RESULTADOS: No grupo de laringectomizados, houve maior frequência de hipogeusia (80%; p < 0,05, assim como de hiposmia (88%; p < 0,001, isoladas e concomitantes (72%; p < 0,001. Na discriminação dos sabores, o sabor amargo não diferiu entre os grupos, diferentemente dos demais sabores. No aspecto olfatório, os laringectomizados tiveram pior desempenho na detecção de odores de alerta e os relacionados à alimentação. Identificou-se que história de tabagismo e de alcoolismo foi significantemente mais frequente dentre laringectomizados. CONCLUSÃO: A diminuição das funções olfatória e gustatória em laringectomizados totais foi evidenciada nesse estudo.

RIA: Principles and application

International Nuclear Information System (INIS)

Pappas, A.A.; Glassman, A.B.

1983-01-01

What is the future of RIA? Has the application of RIA peaked? Will other and competing tests such as immunofluorescence and ELISA systems displace or replace the method? RIA is a sensitive, precise, and very often specific analytical tool. Its primary advantage is exquisite sensitivity. Problems related to specificity of antibody and/or antigen identification are reviewed in this paper. The same limitations will be encountered in the similar techniques of enzyme immunologic determination. Increasing difficulties with waste disposal of either radioactive material and/or organic solvents will cause those who utilize radionuclides to look again at alternatives. RIA has been an exciting developmental tool that has led the authors to look at dynamic physiologic and biochemical interactions. The time may come when there is replacement of the radionuclide portion by enzymes or fluorescent material

Verification of computer code FPRETAIN with respect to RIA data from SPERT and PBF experiments

International Nuclear Information System (INIS)

Heo, Young-Ho; Yanagisawa, Kazuaki.

1992-12-01

This report presents the comparisons between calculated and measured fuel rod behavior and the analysis of stress for preirradiated LWR type fuel rods during reactivity initiated accident (RIA) conditions. For the calculations, FPRETAIN computer code which can simulate the fuel behavior under RIA conditions at extended burnup stage was used. For the experimental, data obtained from the Special Power Excursion Reactor Test (SPERT) and the Power Burst Facility (PBF) tests were used. The results of the comparisons showed that the FPRETAIN code predicted well the tendency of the fuel rod behavior during RIA. From the results of the stress analysis, it was found that the maximum hoop stress of cladding was not proportional to the energy deposition of fuel rod. Calculated cladding maximum hoop stress of failed fuel at high burnup was not lower than that of intact fresh or low burnup fuel. (author)

LOCA and RIA studies at JAERI

International Nuclear Information System (INIS)

Sugiyama, Tomoyuki; Nagase, Fumihisa; Nakamura, Jinichi; Fuketa, Toyoshi

2004-01-01

To provide a data base for the regulatory guide of light water reactors, behavior of reactor fuels during off-normal and postulated accident conditions such as loss-of-coolant accident (LOCA) and reactivity-initiated accident (RIA) is being studied at the Japan Atomic Energy Research Institute (JAERI). The LOCA program consists of integral thermal shock tests and other separate tests for oxidation rate and mechanical property of fuel claddings. Prior to the tests on irradiated claddings, the tests have been conducted on non-irradiated claddings to examine separate effects of corrosion and hydrogen absorption during reactor operation. The tests on irradiated claddings have recently been started and results have been obtained. As for an RIA study, a series of experiments with high burnup fuel rods is being performed by using pulse irradiation capability of the NSRR. This paper presents recent results obtained from the LOCA and RIA studies at JAERI. (Author)

QC in RIA

International Nuclear Information System (INIS)

Little, J.

1989-01-01

A Regional Health Authority expert from the service which performs radioimmunoassays (RIA) and immunoradiometric assays (IRMA) discusses the importance of quality control in these techniques. Originally developed as an aid to endocrinology, applications are now much more widely based and include virology, microbiology, drugs testing, immunology, parasitology, veterinary science and the food industry. The origins of errors in the practice of RIA are examined, with and between batches and the limitations placed on accuracy are explained. Measurement variability between laboratories is also mentioned. (U.K.)

Eficiência dos testes cromáticos de comparação na discromatopsia hereditária: relato de casos

OpenAIRE

Fernandes,Luciene Chaves; Urbano,Lúcia Carvalho de Ventura

2008-01-01

As autoras relatam dois casos de discromatopsia hereditária e discutem a eficiência dos testes cromáticos no diagnóstico de uma discromatopsia. Os pacientes foram reprovados em diferentes concursos públicos federais por apresentarem diagnóstico de discromatopsia hereditária pelo teste de Ishihara. Submeteram-se a exame oftalmológico, com resultados dentro da normalidade. Procuraram novo parecer para melhor caracterização da sua discromatopsia. Não havia sintomas relacionados à deficiência. Os...

A 20 kw beam-on-target test of a high-power liquid lithium target for RIA

International Nuclear Information System (INIS)

Reed, Claude B.; Nolen, Jerry A.; Specht, James R.; Novick, Vincent J.; Plotkin, Perry

2004-01-01

The high-power heavy-ion beams produced by the Rare Isotope Accelerator (RIA) driver linac have large energy deposition density in solids and in many cases no solid materials would survive the full beam power. Liquid lithium technology has been proposed to solve this problem in RIA. Specifically, a windowless target for the production of radioactive ions via fragmentation, consisting of a jet of about 3 cm thickness of flowing liquid lithium, exposed to the beamline vacuum [1,2] is being developed. To demonstrate that power densities equivalent to a 200-kW RIA uranium beam, deposited in the first 4 mm of a flowing lithium jet, can be handled by the windowless target design, a high power 1 MeV Dynamitron was leased and a test stand prepared to demonstrate the target's capability of absorbing and carrying away a 20kW heat load without disrupting either the 5 mm x 10 mm flowing lithium jet target or the beam line vacuum

Simulator testing system (STS)

International Nuclear Information System (INIS)

Miller, V.N.

1990-01-01

In recent years there has been a greater demand placed on the capabilities and time usage of real-time nuclear plant simulators due to NRC, INPO and utilities requirements. The requirements applied to certification, new simulators, upgrades, modifications, and maintenance of the simulators vary; however, they all require the capabilities of the simulator to be tested whether it is for NRC 10CFR55.45b requirements, ATP testing of new simulators, ATP testing of upgrades with or without panels, adding software/hardware due to plant modifications, or analyzing software/hardware problems on the simulator. This paper describes the Simulator Testing System (STS) which addresses each one of these requirements placed on simulators. Special attention will be given to ATP testing of upgrades without the use of control room panels. The capabilities and applications of the four parts of STS which are the Display Control Software (DCS), Procedure Control Software (PCS), Display Generator Software (DGS) and the Procedure Generator Software (PGS) will be reviewed

Reactivity Insertion Accident (RIA) Capability Status in the BISON Fuel Performance Code

Energy Technology Data Exchange (ETDEWEB)

Williamson, Richard L. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Folsom, Charles Pearson [Idaho National Lab. (INL), Idaho Falls, ID (United States); Pastore, Giovanni [Idaho National Lab. (INL), Idaho Falls, ID (United States); Veeraraghavan, Swetha [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-05-01

One of the Challenge Problems being considered within CASL relates to modelling and simulation of Light Water Reactor LWR) fuel under Reactivity Insertion Accident (RIA) conditions. BISON is the fuel performance code used within CASL for LWR fuel under both normal operating and accident conditions, and thus must be capable of addressing the RIA challenge problem. This report outlines required BISON capabilities for RIAs and describes the current status of the code. Information on recent accident capability enhancements, application of BISON to a RIA benchmark exercise, and plans for validation to RIA behavior are included.

Possibilities for Beam Stripping Solutions at a Rare Isotope Accelerator (RIA)

International Nuclear Information System (INIS)

Greife, Uwe

2006-01-01

As part of the DOE RIA R and D effort we investigated the possibilities and problems of beam strippers in the different heavy ion accelerator components of a possible Rare Isotope Accelerator (RIA) facility. We focused on two beam stripping positions in the RIA heavy ion driver where benchmark currents of up to 5 particle (micro)A 238-U were projected at energies of 10.5 MeV/u and 85 MeV/u respectively. In order to select feasible stripper materials, data from experiments with Uranium beams at Texas A and M and GSI were evaluated. Based on these results thermal estimates for a possible design were calculated and cooling simulations with commercially available software performed. Additionally, we performed simulations with the GEANT4 code on evaluating the radiation environment for our beam stripping solution at the 85 MeV/u position in the RIA driver

Fission gas induced deformation model for FRAP-T6 and NSRR irradiated fuel test simulations

Energy Technology Data Exchange (ETDEWEB)

Nakamura, Takehiko; Sasajima, Hideo; Fuketa, Toyoshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Hosoyamada, Ryuji; Mori, Yukihide

1996-11-01

Pulse irradiation tests of irradiated fuels under simulated reactivity initiated accidents (RIAs) have been carried out at the Nuclear Safety Research Reactor (NSRR). Larger cladding diameter increase was observed in the irradiated fuel tests than in the previous fresh fuel tests. A fission gas induced cladding deformation model was developed and installed in a fuel behavior analysis code, FRAP-T6. The irradiated fuel tests were analyzed with the model in combination with modified material properties and fuel cracking models. In Test JM-4, where the cladding temperature rose to higher temperatures and grain boundary separation by the pulse irradiation was significant, the fission gas model described the cladding deformation reasonably well. The fuel had relatively flat radial power distribution and the grain boundary gas from the whole radius was calculated to contribute to the deformation. On the other hand, the power density in the irradiated LWR fuel rods in the pulse irradiation tests was remarkably higher at the fuel periphery than the center. A fuel thermal expansion model, GAPCON, which took account of the effect of fuel cracking by the temperature profile, was found to reproduce well the LWR fuel behavior with the fission gas deformation model. This report present details of the models and their NSRR test simulations. (author)

Repository simulation tests

International Nuclear Information System (INIS)

Wicks, G.G.; Bibler, N.E.; Jantzen, C.M.; Plodinec, M.J.

1984-01-01

The repository simulation experiments described in this paper are designed to assess the performance of SRP waste glass under the most realistic repository conditions that can be obtained in the laboratory. These tests simulate the repository environment as closely as possible and introduce systematically the variability of the geology, groundwater chemistry, and waste package components during the leaching of the waste glass. The tests evaluate waste form performance under site-specific conditions, which differ for each of the geologic repositories under consideration. Data from these experiments will aid in the development of a realistic source term that can describe the release of radionuclides from SRP waste glass as a component of proposed waste packages. Hence, this information can be useful to optimize waste package design for SRP waste glass and to provide data for predicting long-term performance and subsequent conformance to regulations. The repository simulation tests also help to bridge the gap in interpreting results derived from tests performed under the control of the laboratory to the uncertainity and variability of field tests. In these experiments, site-specific repository components and conditions are emphasized and only the site specific materials contact the waste forms. An important feature of these tests is that both actual and simulated waste glasses are tested identically. 7 figures, 2 tables

Analysis of ULOF accident in Monju reflecting the knowledge from CABRI in-pile experiments and others

International Nuclear Information System (INIS)

Sato, Ikken; Tobita, Yoshiharu; Suzuki, Tohru; Kawada, Ken-ichi; Fukano, Yoshitaka; Fujita, Satoshi; Kamiyama, Kenji; Ishikawa, Makoto; Nonaka, Nobuyuki; Usami, Shin

2007-05-01

In the safety evaluation in the original licensing procedure of the prototype FBR Monju, mechanical energy release during an unprotected loss-of-flow (ULOF) event, one of technically inconceivable events postulated beyond design basis, was evaluated and shown that the radiological consequence is suitably limited. Since the sodium leakage accident in the secondary heat-transport system, the Monju plant has been kept under the stand-by condition for more than ten years and the composition of fuel in the current reactor core has changed due to decay of a plutonium isotope into americium. This change in fuel composition affects the neutronic characteristics of the core, requiring assessment of its effect on safety. In this study, event sequences of ULOF were analyzed to assess the effect of the change in neutronic characteristics on the mechanical energy release during ULOF. A significant advance has been made in the safety analysis codes reflecting the knowledge obtained through extensive safety research programs in the last decades, notably the CABRI in-pile experiments. The present results with the advanced analysis codes showed that the mechanical energy release in the current Monju core with the changed neutronic characteristics would not exceed the value evaluated formerly. (author)

Physics calculations for the RIA 1-3 irradiated rod test

International Nuclear Information System (INIS)

Young, T.E.

1981-06-01

The RIA 1-3 test would employ a square array of four pre-irradiated BWR rods to provide information on fuel failure modes and consequences of postulated Reactivity Initiated Accidents in power reactors. Calculations were done to: (1) predict R-O power distributions in the test rods for thermal-hydraulic and fuel-failure analysis; and (2) predict the steady-state and transient ratios of test fuel energy deposition to core energy deposition (Figures of Merit). Fission distributions for the test were computed with the RAFFL Monte Carlo code using an external neutron current source from a complete-reactor radial calculation with the SCAMP S/sub n/ code. Energies per fission for the rods were computed using the SINBAD buildup and depletion code, the GAMSOR gamma ray source code, and the QAD-BSA point-kernel shielding code. The calculated rod average-to-test average energy deposition ratios are 0.99, 0.99, and 0.97 for the rods irradiated to approximately 12 CWd/tu, and 1.04 for the rod irradiated to 4.8 GWd/tu. The maximum deviation of the power density of 1/12-rod azimuthal segments from the rod average is 4%. For an estimated control rod position of 0.591 m withdrawn the predicted radial average energy deposition at the axial peak in an average test rod is 1.71 (kW/m)/MW during preconditioning, and 1.84 (kJ/kg UO 2 ) MW.S during the burst. 16 figures, 7 tables

Simulator for materials testing reactors

International Nuclear Information System (INIS)

Takemoto, Noriyuki; Sugaya, Naoto; Ohtsuka, Kaoru; Hanakawa, Hiroki; Onuma, Yuichi; Hosokawa, Jinsaku; Hori, Naohiko; Kaminaga, Masanori; Tamura, Kazuo; Hotta, Kohji; Ishitsuka, Tatsuo

2013-06-01

A real-time simulator for both reactor and irradiation facilities of a materials testing reactor, “Simulator of Materials Testing Reactors”, was developed for understanding reactor behavior and operational training in order to utilize it for nuclear human resource development and to promote partnership with developing countries which have a plan to introduce nuclear power plant. The simulator is designed based on the JMTR (Japan Materials Testing Reactor), and it simulates operation, irradiation tests and various kinds of anticipated operational transients and accident conditions caused by the reactor and irradiation facilities. The development of the simulator was sponsored by the Japanese government as one of the specialized projects of advanced research infrastructure in order to promote basic as well as applied researches. This report summarizes the simulation components, hardware specification and operation procedure of the simulator. (author)

Neutronics and radiation field studies for the RIA fragmentation target area

Energy Technology Data Exchange (ETDEWEB)

Reyes, Susana [Lawrence Livermore National Laboratory, P.O. Box 808, L-446, Livermore, CA 94550 (United States)]. E-mail: reyes20@llnl.gov; Boles, Jason L. [Lawrence Livermore National Laboratory, P.O. Box 808, L-446, Livermore, CA 94550 (United States); Ahle, Larry E. [Lawrence Livermore National Laboratory, P.O. Box 808, L-446, Livermore, CA 94550 (United States); Stein, Werner [Lawrence Livermore National Laboratory, P.O. Box 808, L-446, Livermore, CA 94550 (United States)

2006-06-23

Neutronics simulations and activation evaluations are currently in progress as part of the pre-conceptual research and development effort for the Rare Isotope Accelerator (RIA). The RIA project involves generating heavy element ion beams with powers up to 400 kw for use in a fragmentation target line to produce selected ion beams for physics research experiments. Designing a fragmentation beam dump for RIA is one of the most critical challenges for such a facility. Here, we present the results from neutronics and radiation field assessments for various beam dump concepts that can meet requirements for the RIA fragmentation line. Preliminary results from heavy ion transport including radiation damage evaluations for the RIA fragmentation beam dump are also presented. Initial neutronics and activation studies will be incorporated with other target area considerations to identify important challenges and explore possible solutions.

Neutronics and radiation field studies for the RIA fragmentation target area

Science.gov (United States)

Reyes, Susana; Boles, Jason L.; Ahle, Larry E.; Stein, Werner

2006-06-01

Neutronics simulations and activation evaluations are currently in progress as part of the pre-conceptual research and development effort for the Rare Isotope Accelerator (RIA). The RIA project involves generating heavy element ion beams with powers up to 400 kW for use in a fragmentation target line to produce selected ion beams for physics research experiments. Designing a fragmentation beam dump for RIA is one of the most critical challenges for such a facility. Here, we present the results from neutronics and radiation field assessments for various beam dump concepts that can meet requirements for the RIA fragmentation line. Preliminary results from heavy ion transport including radiation damage evaluations for the RIA fragmentation beam dump are also presented. Initial neutronics and activation studies will be incorporated with other target area considerations to identify important challenges and explore possible solutions.

On the behaviour of dissolved fission gases prior to transient testing of fuel pins

International Nuclear Information System (INIS)

Wood, M.H.; Matthews, J.R.

1978-10-01

The TREAT and CABRI series of reactor safety experiments on irradiated fuel require the transfer of fuel pins from the reactor in which the fuel has achieved some burn-up to the test facility. Subsequently, the fuel is restored to power in the test facility for some time before transient heating is initiated. Such pre-test manoeuvres, where the fuel is subjected to changes in the fission rate and temperature, may have important consequences for the fission gas behaviour during the transient experiment. The results of rate theory calculations are used to assess these effects. (author)

Possibilities for beam stripping solutions at a rare isotope accelerator (RIA)

International Nuclear Information System (INIS)

Greife, Uwe; Simmons, Ellen; Erikson, Luke; Jewett, Cybele; Livesay, Jake; Chipps, Kelly

2007-01-01

We investigated the possibilities and problems of beam strippers in the different heavy ion accelerator components of a possible rare isotope accelerator (RIA) facility. We focused on two beam stripping positions in the RIA heavy ion driver where benchmark currents of up to 5 particle μA 238 U were projected at energies of 10.5 MeV/u and 85 MeV/u, respectively. In order to select feasible stripper materials, data from experiments with uranium beams at the Texas A and M cyclotron and the Gesellschaft fuer Schwerionenforschung (GSI) accelerator were evaluated. Based on these results thermal estimates for a possible design were calculated and cooling simulations with commercially available software performed. Additionally, we performed simulations with the GEANT4 code on evaluating the radiation environment for our beam stripping solution at the 85 MeV/u position in the RIA driver

Radioimmunoassay with heterologous antibody (hetero-antibody RIA)

International Nuclear Information System (INIS)

Iwasawa, Atsushi; Hayashi, Hiroaki; Itoh, Zen; Wakabayashi, Katsumi

1991-01-01

To develop a homologous radioimmunoassay (RIA) for a hormone of a small or rare animal often meets difficulty in collecting a large amount of purified antigen required for antibody production. On the other hand, to employ a heterologous RIA to estimate the hormone often gives poor sensitivity. To overcome this difficulty, a 'hetero-antibody' RIA was studied. In a hetero-antibody RIA system, a purified preparation of a hormone is used for radioiodination and standardization and a heterologous antibody to the hormone is used for the first antibody. Canine motilin and rat LH were selected as examples, and anti-porcine motilin and anti-hCG, anti-hCGβ or anti-ovine LHβ was used as the heterologous antibody. The sensitivities of the hetero-antibody RIAs were much higher than those of heterologous RIAs in any case, showing that these hetero-antibody RIA systems were suitable for practical use. To clarify the principle of hetero-antibody RIA, antiserum to porcine motilin was fractionated on an affinity column where canine motilin was immobilized. The fraction bound had greater constants of affinity with both porcine and canine motilins than the rest of the antibody fractions. This fraction also reacted with a synthetic peptide corresponding to the C-terminal sequence common to porcine and canine motilins in a competitive binding test with labeled canine motilin. These results suggest that an antibody population having high affinity and cross-reactivity is present in polyclonal antiserum and indicate that the population can be used in hetero-antibody RIA at an appropriate concentration. (author)

Toroidal simulation magnet tests

International Nuclear Information System (INIS)

Walstrom, P.L.; Domm, T.C.

1975-01-01

A number of different schemes for testing superconducting coils in a simulated tokamak environment are analyzed for their merits relative to a set of test criteria. Two of the concepts are examined in more detail: the so-called cluster test scheme, which employs two large background field coils, one on either side of the test coil, and the compact torus, a low-aspect ratio toroidal array of a small number of coils in which all of the coils are essentially test coils. Simulation of the pulsed fields of the tokamak is discussed briefly

Parametric study of fuel rod behaviour during the RIA using the modified FALCON code

International Nuclear Information System (INIS)

Khvostov, G.; Zimmermann, M.A.; Ledergerber, G.

2010-01-01

Presented in the paper are the results of a parametric study with the use of optimised modules of the FALCON code (FALCON-PSI) that addresses the effects of the selected characteristics of fast thermal transients (e.g., impulse width), fuel rod design (e.g., active fuel attack length) and boundary conditions (e.g., the coolant conditions) on fuel behaviour during a RIA. Specifically, the analysis of the governing processes for the fuel rod behaviour during the RIA events simulated in the experimental facility of the Nuclear Safety Research Reactor (NSRR, Japan) are in the focus of the present study. The results obtained can be useful for a better transfer of the NSRR test results in relation to the corresponding behaviour in LWRs and furthermore might also support the planning of future additional experiments. (authors)

Evaluation of the SCANAIR Computer Code

International Nuclear Information System (INIS)

Jernkvist, Lars Olof; Massih, Ali

2001-11-01

-burnup fuel rod. This test case is used to check the validity of SCANAIR installation in a new computer environment, but also to examine the output response of the code to an RIA-type load. Moreover, we have used independent computational methods to verify and compare some of the SCANAIR results for this reference case. The outcome is encouraging. In addition, we have attempted to simulate with SCANAIR a ramp test performed at the Studsvik R2 reactor, and a rod in the Studsvik TRANSRAMP-IV project was selected for this purpose. Although SCANAIR is not designed to simulate 'moderate' transients like the one considered here, we have found the results on fission gas release and clad plastic strain in fair agreement with measured data. Finally, we have performed computations on an existent RIA test made on a pre-irradiated rod in the CABRI reactor, to wit the REP-Na2 rod in the REP-Na test series. Rod Na2 was subjected to a fast RIA-type pulse with a pulse-width of 0.9 ms and a peak linear power density of about 40 MW/m. Also for this test case, SCANAIR exhibited good performance with reasonable execution times on personal computers with the Linux operating system. We have not subjected SCANAIR to extensive testing and benchmarking against experimental data, nor to a wide-range of parametric studies to locate possible faults of the code in analyses of highly irradiated fuel rods under RIA. However, our evaluation and testing indicate that the models used for pellet and clad (visco)plastic deformation and axial mixing of released fission products should be improved. Nevertheless, our limited study with SCANAIR has been positive. Although it would benefit from further calibration to experimental data, we believe that SCANAIR is an adequate computer code for predicting thermal-mechanical behavior of a fuel rod during a postulated RIA

Safety test facilities. Needs and concepts. A French evaluation

International Nuclear Information System (INIS)

Tretiakoff, O.; Bailly, J.

1976-01-01

The fuel behavior of LMFBRs in the event of an accident has been tested in-pile in the SCARABEE program. These tests will be carried on in the framework of an international cooperation on irradiated fuels: this is the purpose of the CABRI and SCARABEE N programs. All those studies should enable to assess safety margins between accident conditions and the technical specifications of the reactor. The purpose of this paper is to explain how a logical set of simple observations has led us to the present state of the Cadarache in-pile experimental safety program and how it may help us to find our way in a dense forest of both technical and psychological difficulties

Weightless environment simulation test; Mujuryo simulation shiken

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, K.; Yamamoto, T.; Kato, F. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1997-07-20

Kawasaki Heavy Industries, Ltd., delivered a Weightless Environment Test System (WETS) to National Space Development Agency of Japan in 1994. This system creates a weightless environment similar to that in space by balancing gravity and buoyancy in the water, and is constituted of a large water tank, facilities to supply air and cooling water to space suits worn in the water, etc. In this report, a weightless environment simulation test and the facilities to supply air and cooling water are described. In the weightless environment simulation test, the astronaut to undergo tests and training wears a space suit quite similar to the suit worn on the orbit, and performs EVA/IVA (extravehicular activities/intravehicular activities) around a JEM (Japanese Experimental Module) mockup installed in the water verifying JEM design specifications, preparing manuals for operations on the orbit, or receives basic space-related drill and training. An EVA weightless environment simulation test No. 3 was accomplished with success in January, 1997, when the supply of breathing water and cooling water to the space suit, etc., were carried out with safety and reliability. 2 refs., 8 figs., 2 tabs.

HISTÓRIAS DE RETIRANTES: RUÍNAS LITERÁRIAS NO CINEMA

Directory of Open Access Journals (Sweden)

Elisabete Alfeld Rodrigues

2009-06-01

Full Text Available Em O caminho das nuvens, Vicente Amorim conta a história da retirada de uma família do interior nordestino para a região sudeste. Uma história que já foi muitas vezes contada, por exemplo, em Vidas Secas: primeiro, na literatura, por Graciliano Ramos e, depois, no cinema, por Nélson Pereira dos Santos. Na retirada contada por Amorim, a migração não ocorre pelos passos na aridez do sertão; ela acontece por bicicletas nas rodovias, estradas e pequenas cidades que a família – pai, mãe e cinco filhos – percorre para chegar à cidade do Rio de Janeiro. A família se desloca da Paraíba em busca de um emprego de mil reais por mês que só pode ser encontrado no sudeste do Brasil – este motivo desencadeador parte de uma história factual. O filme é uma releitura que resgata a literatura, o cinema e a história factual promovendo uma relação dialógica construída por fragmentos das várias histórias.

Numerical simulations of rubber bearing tests and shaking table tests

International Nuclear Information System (INIS)

Hirata, K.; Matsuda, A.; Yabana, S.

2002-01-01

Test data concerning rubber bearing tests and shaking table tests of base-isolated model conducted by CRIEPI are provided to the participants of Coordinated Research Program (CRP) on 'Intercomparison of Analysis Methods for predicting the behaviour of Seismically Isolated Nuclear Structure', which is organized by International Atomic Energy Agency (IAEA), for the comparison study of numerical simulation of base-isolated structure. In this paper outlines of the test data provided and the numerical simulations of bearing tests and shaking table tests are described. Using computer code ABAQUS, numerical simulations of rubber bearing tests are conducted for NRBs, LRBs (data provided by CRIEPI) and for HDRs (data provided by ENEA/ENEL and KAERI). Several strain energy functions are specified according to the rubber material test corresponding to each rubber bearing. As for lead plug material in LRB, mechanical characteristics are reevaluated and are made use of. Simulation results for these rubber bearings show satisfactory agreement with the test results. Shaking table test conducted by CRIEPI is of a base isolated rigid mass supported by LRB. Acceleration time histories, displacement time histories of the isolators as well as cyclic loading test data of the LRB used for the shaking table test are provided to the participants of the CRP. Simulations of shaking table tests are conducted for this rigid mass, and also for the steel frame model which is conducted by ENEL/ENEA. In the simulation of the rigid mass model test, where LRBs are used, isolators are modeled either by bilinear model or polylinear model. In both cases of modeling of isolators, simulation results show good agreement with the test results. In the case of the steel frame model, where HDRs are used as isolators, bilinear model and polylinear model are also used for modeling isolators. The response of the model is simulated comparatively well in the low frequency range of the floor response, however, in

Simulant Development for LAWPS Testing

Energy Technology Data Exchange (ETDEWEB)

Russell, Renee L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Schonewill, Philip P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Burns, Carolyn A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-05-23

This report describes simulant development work that was conducted to support the technology maturation of the LAWPS facility. Desired simulant physical properties (density, viscosity, solids concentration, solid particle size), sodium concentrations, and general anion identifications were provided by WRPS. The simulant recipes, particularly a “nominal” 5.6M Na simulant, are intended to be tested at several scales, ranging from bench-scale (500 mL) to full-scale. Each simulant formulation was selected to be chemically representative of the waste streams anticipated to be fed to the LAWPS system, and used the current version of the LAWPS waste specification as a formulation basis. After simulant development iterations, four simulants of varying sodium concentration (5.6M, 6.0M, 4.0M, and 8.0M) were prepared and characterized. The formulation basis, development testing, and final simulant recipes and characterization data for these four simulants are presented in this report.

Simulação das emissões atmosféricas sobre o município de Araucária com uso do modelo AERMOD Simulation of atmospheric emissions over Araucaria municipality using the AERMOD model

Directory of Open Access Journals (Sweden)

Amarildo Barbon

2010-06-01

Full Text Available O objetivo do presente trabalho foi avaliar o uso de um modelo computacional de dispersão de poluentes em meio atmosférico, modelo AERMOD, na modelagem da dispersão das emissões atmosféricas produzidas pelas principais indústrias do município de Araucária. Os dados estimados de emissões de poluentes na atmosfera referem-se às fontes estacionárias da refinaria Presidente Getúlio Vargas (REPAR e das principais indústrias que compõem o distrito industrial de Araucária. Não foram utilizados dados das fontes móveis por representarem uma pequena parcela da carga total de poluentes. Inicialmente, o modelo AERMOD foi avaliado pela comparação entre concentrações simuladas e concentrações observadas de óxidos de nitrogênio (NOx, óxidos de enxofre (SOx monóxido de carbono (CO e materiais particulados (MP na estação de amostragem de qualidade do ar existente na REPAR. Realizou-se uma análise de sensibilidade do modelo AERMOD em diferentes cenários de emissões, procurando avaliar a influência da variação dos parâmetros de entrada do modelo sobre as concentrações simuladas para a estação REPAR e para a região central do município de Araucária.The present paper aims to evaluate the use of the air quality model AERMOD to simulate the dispersion of atmospheric emissions produced by the main industries located in the Araucária municipality area. Pollutant emissions were estimated for both stationary sources in the President Getúlio Vargas Refinery (REPAR and stationary sources in the main industries located at the industrial district of Araucária municipality. As the pollutant emissions from mobile sources are small in comparison to stationary sources, the simulations were performed using only emissions from the stationary sources. Initially, the AERMOD model was evaluated by comparing simulated concentrations and observed concentrations from the air quality station located inside the REPAR. The observed data concerns

Simulation-based Testing of Control Software

Energy Technology Data Exchange (ETDEWEB)

Ozmen, Ozgur [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Nutaro, James J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sanyal, Jibonananda [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Olama, Mohammed M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-02-10

It is impossible to adequately test complex software by examining its operation in a physical prototype of the system monitored. Adequate test coverage can require millions of test cases, and the cost of equipment prototypes combined with the real-time constraints of testing with them makes it infeasible to sample more than a small number of these tests. Model based testing seeks to avoid this problem by allowing for large numbers of relatively inexpensive virtual prototypes that operate in simulation time at a speed limited only by the available computing resources. In this report, we describe how a computer system emulator can be used as part of a model based testing environment; specifically, we show that a complete software stack including operating system and application software - can be deployed within a simulated environment, and that these simulations can proceed as fast as possible. To illustrate this approach to model based testing, we describe how it is being used to test several building control systems that act to coordinate air conditioning loads for the purpose of reducing peak demand. These tests involve the use of ADEVS (A Discrete Event System Simulator) and QEMU (Quick Emulator) to host the operational software within the simulation, and a building model developed with the MODELICA programming language using Buildings Library and packaged as an FMU (Functional Mock-up Unit) that serves as the virtual test environment.

Safety test facilities. Needs and concepts. A French evaluation

International Nuclear Information System (INIS)

Tretiakoff, O.; Bailly, J.

1976-01-01

The fuel behaviour of LMFBRs in the event of an accident has been tested in-pile in the SCARABEE program (local blockage, sudden flow reduction and pump coast-down at constant power). These tests will be carried on in the framework of an international cooperation on irradiated fuels: this is the purpose of the CABRI and SCARABEE N programs. All those studies should enable to assess safety margins between accident conditions and the technical specifications of the reactor. The paper explains how a logical set of simple observations has led to the present state of the Cadarache in-pile experimental safety program and how it may help to find the way in a dense forest of both technical and psychological difficulties

Tratamento cirúrgico da artéria coronária direita intra-atrial

Directory of Open Access Journals (Sweden)

José Carlos R. IGLÉZIAS

1997-07-01

Full Text Available A localização intracavitária da artéria coronária é rara. Segundo Ochsner & Mills (1, ela ocorreu com a artéria coronária direita em 0,9% e com o ramo interventricular em 0,2%. A localização da lesão e as condições patológicas relacionadas ao comprimento e diâmetro da coronária podem auxiliar na exposição da coronária intracavitária para uma revascularização apropriada. Freqüentemente os cirurgiões não estão habituados com a posição intracavitária e, durante a dissecção, podem abrir uma câmara cardíaca onde o vaso penetra. Os problemas que podem advir dai são a entrada de ar para a cavidade, a dificuldade na exposição do vaso, o sangramento e a obstrução da artéria durante o fechamento da miotomia. São relatados os casos de 3 pacientes que necessitaram de revascularização cirúrgica do miocárdio e que apresentavam a artéria coronária direita intracavitária. A localização e o comprimento da porção intracavitária da artéria auxiliam no manejo intra-operatório. A técnica utilizada para o fechamento da cavidade variou entre a anastomose na posição intracavitária com o fechamento da miotomia ao redor do enxerto (Figura 1, a liberação da artéria coronária para uma posição superficial (Figura 2, seguida da anastomose e fechamento da cavidade com sutura simples, feita subepicárdica.An intracavitary location of a coronary artery is rare in our surgical experience with revascularization. This variant has occured in the right coronary artery (0.01% and in left anterior descending coronary artery (0.2%. The location of the lesion and the pathological condition, length and size of the coronary may dictate exposure of an intracavitary coronary artery for proper revascularization; more commonly surgeons are anaware of the intracavitary position and during intramyocardial dissection of an artery will open a cardiac chamber where the vessel traverses the cavity. Problems that arise are introducion

Computational needs for the RIA accelerator systems

International Nuclear Information System (INIS)

Ostroumov, P.N.; Nolen, J.A.; Mustapha, B.

2006-01-01

This paper discusses the computational needs for the full design and simulation of the RIA accelerator systems. Beam dynamics simulations are essential to first define and optimize the architectural design for both the driver linac and the post-accelerator. They are also important to study different design options and various off-normal modes in order to decide on the most-performing and cost-effective design. Due to the high-intensity primary beams, the beam-stripper interaction is a source of both radioactivation and beam contamination and should be carefully investigated and simulated for proper beam collimation and shielding. The targets and fragment separators area needs also very special attention in order to reduce any radiological hazards by careful shielding design. For all these simulations parallel computing is an absolute necessity

ENSINO DE HISTÓRIA E MEMÓRIA SOCIAL: A ARGUMENTAÇÃO COMO POSSIBILIDADE PEDAGÓGICA PARA A HISTÓRIA ENSINADA

Directory of Open Access Journals (Sweden)

Patricia Bastos de Azevedo

2010-12-01

Full Text Available Este texto é fruto da pesquisa desenvolvida no mestrado em Educação, no período de 2000 a 2003, na Universidade Federal Fluminense. Buscou-se identificar como os elementos história e memória se constituem no espaço da sala de aula e produzem, assim, a história ensinada. A teoria habermasiana da ação comunicativa é o principal alicerce teórico desta pesquisa; dessa forma, procurou-se relacionar essa teoria com a construção da memória social e seu papel no fazer pedagógico da sala de aula de história.

Nuclear system test simulator

International Nuclear Information System (INIS)

Sawyer, S.D.; Hill, W.D.; Wilson, P.A.; Steiner, W.M.

1987-01-01

A transportable test simulator is described for a nuclear power plant. The nuclear power plant includes a control panel, a reactor having actuated rods for moving into and out of a reactor for causing the plant to operate, and a control rod network extending between the control panel and the reactor rods. The network serially transmits command words between the panel and rods, and has connecting interfaces at preselected points remote from the control panel between the control panel and rods. The test simulator comprises: a test simulator input for transport to and connection into the network at at least one interface for receiving the serial command words from the network. Each serial command includes an identifier portion and a command portion; means for processing interior of the simulator for the serial command words for identifying that portion of the power plant designated in the identifier portion and processing the word responsive to the command portion of the word after the identification; means for generating a response word responsive to the command portion; and output means for sending and transmitting the response word to the nuclear power plant at the interface whereby the control panel responds to the response word

Creating and Testing Simulation Software

Science.gov (United States)

Heinich, Christina M.

2013-01-01

The goal of this project is to learn about the software development process, specifically the process to test and fix components of the software. The paper will cover the techniques of testing code, and the benefits of using one style of testing over another. It will also discuss the overall software design and development lifecycle, and how code testing plays an integral role in it. Coding is notorious for always needing to be debugged due to coding errors or faulty program design. Writing tests either before or during program creation that cover all aspects of the code provide a relatively easy way to locate and fix errors, which will in turn decrease the necessity to fix a program after it is released for common use. The backdrop for this paper is the Spaceport Command and Control System (SCCS) Simulation Computer Software Configuration Item (CSCI), a project whose goal is to simulate a launch using simulated models of the ground systems and the connections between them and the control room. The simulations will be used for training and to ensure that all possible outcomes and complications are prepared for before the actual launch day. The code being tested is the Programmable Logic Controller Interface (PLCIF) code, the component responsible for transferring the information from the models to the model Programmable Logic Controllers (PLCs), basic computers that are used for very simple tasks.

RIA for indol alkaloids

International Nuclear Information System (INIS)

Arens, H.

1979-01-01

The technique of RIAs for indol alkaloids (ajmaline, ergotamine, ergocristine, ergometrine, and lysergic acid) is described, and applications for this RIA and the RIA for raubasine and serpentine are mentioned. The indol alkaloide RIAs are shown to be suitable both for alkaloid distribution measurements in Catharantus and Rauwolfia plants and C. purpurea sclerotia as well as for the selection of high-efficiency strains and the optimisation of cultures of plant tissues and saprophytic fungi. (orig./MG) [de

Estradiol RIA kit in clinical practice

International Nuclear Information System (INIS)

Friedrich, W.; Lisse, K.; Bienert, R.; Flentje, H.; Koerner, H.; Wilken, T.; Akademie der Wissenschaften der DDR, Berlin-Buch. Zentralinstitut fuer Isotopen- und Strahlenforschung)

1985-01-01

First clinical experience with a estradiol RIA kit developed in the Central Institute for Isotope- and Radiation Research is reported. The kit was used for the daily control of estradiol level in patients, which were treated within the program for in vitro fertilization and embryo transfer. The time of incubation could be shortened by means of a double antibody technique and by use of a precipitation mixture to 2 h. The intraassay variation is 9.2%, the interassay variation is 15.1%, the recovery rate is 94%. The sensitivity of the test (B 0 -3SD) is about 120 pmol/l. The estradiol RIA kit satisfies clinical requirements. (author)

LOFA and RIA analysis of the Indonesian Multipurpose research reactor RSG-GAS 1)

International Nuclear Information System (INIS)

Endiah Puji Hastuti; Hudi Hastowo; Iman Kuntoro

1999-01-01

Investigation on accident of the Indonesian Multipurpose research reactor RSG-GAS has been performed by computer simulation technique. Two groups of transients were considered, namely transient due to loss of primary cooling system (LOFA) and power excursion due to reactivity insertion (RIA). In such a transient condition, the Common Mode Failure (CMF) is considered and it will induce a situation so called unprotected transient or Anticipated Transient Without Scram (ATWS). RELAP5, PARET-ANL and EUREKA-2RR computer packages have been applied for these analyses. Simulations result done using these computer packages showed that in the occurrence of LOFA and RIA, failure on fuel elements is limited to the region with the highest power factor. (author)

Using contraband simulators for portal metal detector testing

Energy Technology Data Exchange (ETDEWEB)

Murray, D.W.

1992-08-01

Because contraband materials or items are either too dangerous or too expensive, contraband simulators have been widely used to test contraband detection equipment. Very realistic bomb simulators have been used to test x-ray scanners, and common radioactive sources have been used successfully to test the operation of special nuclear material (SNM) radiation detectors. The simulators used to test early metal detectors were also reasonably successful; however, these simulators were rapidly outdated by the introduction of modern active field metal detectors. This paper describes some of the earlier attempts to develop metal detector test simulators. A successful highly enriched uranium (HEU) simulator for metal detector testing is described that has duplicated all the characteristics modern equipment is capable of detecting. The paper also describes the development needed to produce handgun simulators that could be used effectively for metal detector performance testing.

Using contraband simulators for portal metal detector testing

Energy Technology Data Exchange (ETDEWEB)

Murray, D.W.

1992-01-01

Because contraband materials or items are either too dangerous or too expensive, contraband simulators have been widely used to test contraband detection equipment. Very realistic bomb simulators have been used to test x-ray scanners, and common radioactive sources have been used successfully to test the operation of special nuclear material (SNM) radiation detectors. The simulators used to test early metal detectors were also reasonably successful; however, these simulators were rapidly outdated by the introduction of modern active field metal detectors. This paper describes some of the earlier attempts to develop metal detector test simulators. A successful highly enriched uranium (HEU) simulator for metal detector testing is described that has duplicated all the characteristics modern equipment is capable of detecting. The paper also describes the development needed to produce handgun simulators that could be used effectively for metal detector performance testing.

Using sport psychology in simulator testing

International Nuclear Information System (INIS)

Primeau, T.; Chandler, K.

2007-01-01

The paper will cover the methods of simulator testing at Bruce Power and the recent trial of using a sport psychology consultant to help candidates deal with the mental, physiological and emotional responses to simulator examinations. Previous research has shown that mental skills training can enhance the performance of both cognitive and physical skills. As such, it was hypothesized that a structured mental skills program would assist candidates in achieving optimal performance during simulator testing. The paper will be written as a descriptive piece. The paper will offer insight into the benefits of using mental skills training in preparation for simulator testing and the drawbacks as experienced by the Authorized Nuclear Operator (ANO). (author)

A review of experiments and computer analyses on RIAs

International Nuclear Information System (INIS)

Jernkvist, L.O.; Massih, A.R.; In de Betou, J.

2010-01-01

Reactivity initiated accidents (RIAs) are nuclear reactor accidents that involve an unwanted increase in fission rate and reactor power. Reactivity initiated accidents in power reactors may occur as a result of reactor control system failures, control element ejections or events caused by rapid changes in temperature or pressure of the coolant/moderator. our current understanding of reactivity initiated accidents and their consequences is based largely on three sources of information: 1) best-estimate computer analyses of the reactor response to postulated accident scenarios, 2) pulse-irradiation tests on instrumented fuel rodlets, carried out in research reactors, 3) out-of-pile separate effect tests, targeted to explore key phenomena under RIA conditions. In recent years, we have reviewed, compiled and analysed these 3 categories of data. The results is a state-of-the-art report on fuel behaviour under RIA conditions, which is currently being published by the OECD Nuclear Energy Agency. The purpose of this paper is to give a brief summary of this report

Aula de história: subjetividade e memória na aprendizagem de alunos

OpenAIRE

Scoz, Beatriz Judith Lima; Rodrigues, Vilma Nardes Silva

2015-01-01

Este artigo apresenta o relato de uma pesquisa sobre as relações entre memória individual e memória coletiva nas aulas de História para compreender suas interferências na produção de sentidos subjetivos dos alunos na aprendizagem de História. A coleta de dados foi feita a partir do filme "Narradores de Javé" e da "conversação livre" com alunos da 8a série de uma escola pública de São Paulo. A pesquisa fundamenta-se nas concepções teóricas de Halbwachs e Placco, & Souza acerca da memória. No q...

Molecular dynamics simulation of impact test

International Nuclear Information System (INIS)

Akahoshi, Y.; Schmauder, S.; Ludwig, M.

1998-01-01

This paper describes an impact test by molecular dynamics (MD) simulation to evaluate embrittlement of bcc Fe at different temperatures. A new impact test model is developed for MD simulation. The typical fracture behaviors show transition from brittle to ductile fracture, and a history of the impact loads also demonstrates its transition. We conclude that the impact test by MD could be feasible. (orig.)

Molecular dynamics simulation of impact test

Energy Technology Data Exchange (ETDEWEB)

Akahoshi, Y. [Kyushu Inst. of Tech., Kitakyushu, Fukuoka (Japan); Schmauder, S.; Ludwig, M. [Stuttgart Univ. (Germany). Staatliche Materialpruefungsanstalt

1998-11-01

This paper describes an impact test by molecular dynamics (MD) simulation to evaluate embrittlement of bcc Fe at different temperatures. A new impact test model is developed for MD simulation. The typical fracture behaviors show transition from brittle to ductile fracture, and a history of the impact loads also demonstrates its transition. We conclude that the impact test by MD could be feasible. (orig.)

Design and Test of Advanced Thermal Simulators for an Alkali Metal-Cooled Reactor Simulator

Science.gov (United States)

Garber, Anne E.; Dickens, Ricky E.

2011-01-01

The Early Flight Fission Test Facility (EFF-TF) at NASA Marshall Space Flight Center (MSFC) has as one of its primary missions the development and testing of fission reactor simulators for space applications. A key component in these simulated reactors is the thermal simulator, designed to closely mimic the form and function of a nuclear fuel pin using electric heating. Continuing effort has been made to design simple, robust, inexpensive thermal simulators that closely match the steady-state and transient performance of a nuclear fuel pin. A series of these simulators have been designed, developed, fabricated and tested individually and in a number of simulated reactor systems at the EFF-TF. The purpose of the thermal simulators developed under the Fission Surface Power (FSP) task is to ensure that non-nuclear testing can be performed at sufficiently high fidelity to allow a cost-effective qualification and acceptance strategy to be used. Prototype thermal simulator design is founded on the baseline Fission Surface Power reactor design. Recent efforts have been focused on the design, fabrication and test of a prototype thermal simulator appropriate for use in the Technology Demonstration Unit (TDU). While designing the thermal simulators described in this paper, effort were made to improve the axial power profile matching of the thermal simulators. Simultaneously, a search was conducted for graphite materials with higher resistivities than had been employed in the past. The combination of these two efforts resulted in the creation of thermal simulators with power capacities of 2300-3300 W per unit. Six of these elements were installed in a simulated core and tested in the alkali metal-cooled Fission Surface Power Primary Test Circuit (FSP-PTC) at a variety of liquid metal flow rates and temperatures. This paper documents the design of the thermal simulators, test program, and test results.

Test/score/report: Simulation techniques for automating the test process

Science.gov (United States)

Hageman, Barbara H.; Sigman, Clayton B.; Koslosky, John T.

1994-01-01

A Test/Score/Report capability is currently being developed for the Transportable Payload Operations Control Center (TPOCC) Advanced Spacecraft Simulator (TASS) system which will automate testing of the Goddard Space Flight Center (GSFC) Payload Operations Control Center (POCC) and Mission Operations Center (MOC) software in three areas: telemetry decommutation, spacecraft command processing, and spacecraft memory load and dump processing. Automated computer control of the acceptance test process is one of the primary goals of a test team. With the proper simulation tools and user interface, the task of acceptance testing, regression testing, and repeatability of specific test procedures of a ground data system can be a simpler task. Ideally, the goal for complete automation would be to plug the operational deliverable into the simulator, press the start button, execute the test procedure, accumulate and analyze the data, score the results, and report the results to the test team along with a go/no recommendation to the test team. In practice, this may not be possible because of inadequate test tools, pressures of schedules, limited resources, etc. Most tests are accomplished using a certain degree of automation and test procedures that are labor intensive. This paper discusses some simulation techniques that can improve the automation of the test process. The TASS system tests the POCC/MOC software and provides a score based on the test results. The TASS system displays statistics on the success of the POCC/MOC system processing in each of the three areas as well as event messages pertaining to the Test/Score/Report processing. The TASS system also provides formatted reports documenting each step performed during the tests and the results of each step. A prototype of the Test/Score/Report capability is available and currently being used to test some POCC/MOC software deliveries. When this capability is fully operational it should greatly reduce the time necessary

Clarification on RIA Novosti Story

International Nuclear Information System (INIS)

2014-01-01

Full text: ''On 21 May, RIA Novosti news agency published a story headlined IAEA Says Impossible for Ukraine to Switch to US Nuclear Fuel, based on apparent remarks by an Agency official during a News Conference in Moscow. There was some confusion about the official's remarks, which were made in Russian. The resulting RIA Novosti story does not accurately reflect his words, nor the position of the IAEA, which is as follows: The choice of supplier for nuclear fuel is the prerogative of the nuclear operator. Such an approach is not unique to Ukraine. Any change in the supply of fuel to a nuclear power plant requires careful safety assessment and testing. Any such modifications should be approved by the national regulatory body in accordance with national laws, applicable safety regulations and industry best practices.''. (author)

Real time simulator for material testing reactor

Energy Technology Data Exchange (ETDEWEB)

Takemoto, Noriyuki; Imaizumi, Tomomi; Izumo, Hironobu; Hori, Naohiko; Suzuki, Masahide [Japan Atomic Energy Agency, Oarai Research and Development Center, Oarai, Ibaraki (Japan); Ishitsuka, Tatsuo; Tamura, Kazuo [ITOCHU Techno-Solutions Corp., Tokyo (Japan)

2012-03-15

Japan Atomic Energy Agency (JAEA) is now developing a real time simulator for a material testing reactor based on Japan Materials Testing Reactor (JMTR). The simulator treats reactor core system, primary and secondary cooling system, electricity system and irradiation facility systems. Possible simulations are normal reactor operation, unusual transient operation and accidental operation. The developed simulator also contains tool to revise/add facility in it for the future development. (author)

Real time simulator for material testing reactor

International Nuclear Information System (INIS)

Takemoto, Noriyuki; Imaizumi, Tomomi; Izumo, Hironobu; Hori, Naohiko; Suzuki, Masahide; Ishitsuka, Tatsuo; Tamura, Kazuo

2012-01-01

Japan Atomic Energy Agency (JAEA) is now developing a real time simulator for a material testing reactor based on Japan Materials Testing Reactor (JMTR). The simulator treats reactor core system, primary and secondary cooling system, electricity system and irradiation facility systems. Possible simulations are normal reactor operation, unusual transient operation and accidental operation. The developed simulator also contains tool to revise/add facility in it for the future development. (author)

Testing cooperative systems with the MARS simulator

NARCIS (Netherlands)

Netten, B.D.; Wedemeijer, H.

2010-01-01

The complexity of cooperative systems makes the use of high fidelity simulation essential in the development and testing of cooperative applications and their interactions with other cooperative systems. In SAFESPOT a simulator test bench is setup to test the safety margin applications running on

Ground testing and simulation. II - Aerodynamic testing and simulation: Saving lives, time, and money

Science.gov (United States)

Dayman, B., Jr.; Fiore, A. W.

1974-01-01

The present work discusses in general terms the various kinds of ground facilities, in particular, wind tunnels, which support aerodynamic testing. Since not all flight parameters can be simulated simultaneously, an important problem consists in matching parameters. It is pointed out that there is a lack of wind tunnels for a complete Reynolds-number simulation. Using a computer to simulate flow fields can result in considerable reduction of wind-tunnel hours required to develop a given flight vehicle.

The evaluation of CLIA, RIA and MSP-ELISA for measurement of thyroid hormones

International Nuclear Information System (INIS)

Jing Hua; Li Dan; Chen Yiguang; Zhou Huiqin; Xu Liyan

2005-01-01

To compare the characteristics of chemiluminescent immunoassay (CLIA), RIA and magnetic solid phase enzyme-linked immnosorbent assay (MSP-ELISA) in measuring thyroid hormones, TT 3 , TT 4 , FT 3 , FT 4 and TSH were tested in 40 samples of human serum and in standard samples of thyroid hormones by CLIA, RIA and MSP-ELISA respectively. The linearity, relativiy, precision, recovery of these three met hods were compared. The result showed that there were no statistical differences between CLIA, RIA and MSP-ELISA in linearity and relativity. CLIA was better than RIA and MSP-ELISA in precision and accuracy. (authors)

História e memória: a soldadura da imaginação

Directory of Open Access Journals (Sweden)

Brum, Rosemary Fritsch

2006-01-01

Full Text Available Este artigo explora possibilidades em história oral, o desenvolvimento na contemporaneidade das ciências cognitivas e sua aproximação com histórias curtas. Essas direções podem ser fertilizadas pelo pesquisador nos estudos da memória, da narrativa e da oralidade

Postoperative chest physical therapy prevents respiratory complications in patients undergoing esophagectomy Fisioterapia respiratória pós-operatória previne complicações respiratórias em pacientes submetidos à esofagectomia

Directory of Open Access Journals (Sweden)

Adriana C. Lunardi

2011-04-01

Full Text Available BACKGROUND: Esophagectomy presents the highest rate of postoperative pulmonary complications among all types of upper abdominal surgery. The benefits of chest physical therapy in patients undergoing upper abdominal surgery have been shown by many studies; however, its specific effect in patients receiving esophagectomy has been seldom investigated. OBJECTIVES: This study aimed to compare the frequency of respiratory complications in patients undergoing esophagectomy receiving chest physical therapy compared to no treatment. METHODS: 70 consecutive patients were evaluated retrospectively and allocated to two groups: control group (CG=no physical therapy; n=30 and chest physical therapy group (PTG; n=40. Patients received chest physical therapy which includes lung re-expansion and airway clearance maneuvers. They were not submitted to either noninvasive ventilation or exercises with devices that generate airways positive pressure. All patients were instructed to early mobilization. Information about pre-operative and respiratory complications were collected. Statistic analysis to compare the frequency of respiratory complications was performed by the Z test. The significance level was set to 5%. RESULTS: Patients in the CG and PTG were similar in terms of age, BMI, smoking and drinking status, malignant diseases, surgical and anesthesia duration and types of esophagectomy (p>0.05. Our results show that patients received chest physical therapy after esophagectomy had a lower frequency of respiratory complications (15% vs. 37%, pCONTEXTUALIZAÇÃO: A esofagectomia apresenta a maior taxa de complicações pulmonares pós-operatórias dentre as cirurgias abdominais altas. Os benefícios da fisioterapia respiratória em pacientes submetidos à cirurgia abdominal alta convencional têm sido mostrados na literatura, porém esse efeito na esofagectomia tem sido pouco investigado. OBJETIVOS: Comparar a frequência de complicações respiratórias em dois

The use of RIA tests for screening and for monitoring of some diseases

International Nuclear Information System (INIS)

Hegesippe, M.

1979-01-01

Some examples are described concerning the progress realized in the antenatal and neonatal diagnoses of congenital anomalies and in the follow-up of cancer patients using RIA techniques. The frequencies of some well known congenital abnormalities are recalled. The first example concerns Duchene myopathy. A second example, much more advanced, is the antenatal diagnosis of neural tube defects. A third example, already in routine state by state in north America and in Europe is the neonatal screening of congenital hypothyroidism. The last example concerns the use of CEA assay in the evaluation, the prognosis and the follow-up of cancer patient's state. These RIA examples were chosen to illustrate and also to situate the important place of this analytical response among informations available to the clinician

Simulation and material testing of jet engines

International Nuclear Information System (INIS)

Tariq, M.M.

2006-01-01

The NASA software engine simulator version U 1.7a beta has been used for simulation and material testing of jet engines. Specifications of Modem Jet Engines are stated, and then engine simulator is applied on these specifications. This simulator can simulate turbojet, afterburner, turbofan and ram jet. The material of many components of engine may be varied. Conventional and advanced materials for jet engines can be simulated and tested. These materials can be actively cooled to increase the operating temperature limit. As soon as temperature of any engine component exceeds the temperature limit of material, a warning message flashes across screen. Temperature Limits Exceeded. This flashing message remainst here until necessaryc hangesa re carried out in engine operationp rocedure. Selection Criteria of Engines is stated for piston prop, turboprop, turbofan, turbojet, and turbojet with afterburner and Ramjet. Several standard engines are modeled in Engine Simulator. These engines can. be compared by several engineering specifications. The design, modeling, simulation and testing of engines helps to better understand different types of materials used in jet engines. (author)

BWR Full Integral Simulation Test (FIST). Phase I test results

International Nuclear Information System (INIS)

Hwang, W.S.; Alamgir, M.; Sutherland, W.A.

1984-09-01

A new full height BWR system simulator has been built under the Full-Integral-Simulation-Test (FIST) program to investigate the system responses to various transients. The test program consists of two test phases. This report provides a summary, discussions, highlights and conclusions of the FIST Phase I tests. Eight matrix tests were conducted in the FIST Phase I. These tests have investigated the large break, small break and steamline break LOCA's, as well as natural circulation and power transients. Results and governing phenomena of each test have been evaluated and discussed in detail in this report. One of the FIST program objectives is to assess the TRAC code by comparisons with test data. Two pretest predictions made with TRACB02 are presented and compared with test data in this report

Comparative studies of commercially available T4-RIA-kits. Pt. 2

International Nuclear Information System (INIS)

Schmidt, H.A.E.; Lipke, P.

1978-01-01

The investigation of the tested commercially available T 4 -RIA-Kits have shown that: The separation of hypo-, eu- and hyperthyroid values is better with kits a) and f) than with b), c), d) and e), though all kits give acceptable values under routine operating conditions, kit b) takes less time and work than the other tested kits, depending on the kit used, the time needed for 100 determinations varies between 1,5 and 4 hr. A general recommendation for one of the tested T 4 -RIA-Kits cannot be made since the choice of a kit depends not only on the criteria discussed but also on local circumstances. (orig.) [de

Assessment of Core Failure Limits for Light Water Reactor Fuel under Reactivity Initiated Accidents

International Nuclear Information System (INIS)

Jernkvist, Lars Olof; Massih, Ali R.

2004-12-01

significantly lower enthalpies than those required for melting, when the fuel burnup exceeds approximately 40 MWd/kgU. This issue is investigated by reviewing all high-burnup UO 2 fuel rods that have failed in RIA simulation tests in the Japanese Nuclear Safety Research Reactor and the French CABRI pulse reactor to date. Data from thirteen failed rods, with burnups between 44 and 64 MWd/kgU, indicate that clad tube failure does not necessarily lead to fuel pellet dispersal. In fact, the data suggest that a peak fuel radial average enthalpy of at least 500 J/gUO 2 is required to expel a significant part (>10 %) of the fuel inventory into the coolant. However, this empirical enthalpy threshold for fuel dispersal from high-burnup fuel rods cannot be directly applied to light water reactors, since the power pulses and/or the cooling conditions used in the pulse tests differ notably from those expected in LWRs under RIA

Study on the technical parameters of two different systems of RIA performed with solid-phase antibody test tubes prepared with magnetic microparticle covalence conjagation or conventional physical absorption

International Nuclear Information System (INIS)

Chen Zhiqiang; Wang Chengmin; Tang Baojun

2007-01-01

Objective: To investigate a new method of preparation of solid-phase antibody with flurorescein isothioeynate (FITC)-anti FITC magnetic nanoparticles system (for FT 3 and TSH). Methods: FT 3 and TSH monoclonal antibody IgC was la- belied with FITC. Anti-FITC magnetic mieroparticles was prepared and conjugated with the FITC labelled antibody to form the solid - phase coated test tube for RIA. Solid-phase test tube prepared with the conventional physical absorption method was also used for RIA and the technical parameters of the two systems were compared. Results: For FT 3 , the sensitivity was 0.18pmol/L with the new method and 0.43pmol/L with the conventional method. Other parameters were; intra-CV, 8.96% vs 16.26%; inter-CV, 15.25% vs 18.83%, correlation with PR method r=0.9825 vs r=0.9102. For TSH, sensitivity was 0.061 μIU/ml vs 0.04 μ IU/ml, intra- CV, 7.6% vs 6.92%, inter-CV, 8.55% vs 14.23%, correlation between the new and conventional method, r=0. 9987. TSH RIA was especially rapid with the new technic: 79 min vs 190 min. Conclusion: For FT 3 and TSH RIA, the new method takes much less time with increased homogeniety. (authors)

Eficiência dos testes cromáticos de comparação na discromatopsia hereditária: relato de casos Efficiency of color vision tests in hereditary dyschromatopsia: case report

Directory of Open Access Journals (Sweden)

Luciene Chaves Fernandes

2008-08-01

Full Text Available As autoras relatam dois casos de discromatopsia hereditária e discutem a eficiência dos testes cromáticos no diagnóstico de uma discromatopsia. Os pacientes foram reprovados em diferentes concursos públicos federais por apresentarem diagnóstico de discromatopsia hereditária pelo teste de Ishihara. Submeteram-se a exame oftalmológico, com resultados dentro da normalidade. Procuraram novo parecer para melhor caracterização da sua discromatopsia. Não havia sintomas relacionados à deficiência. Os testes Panel D15 simples, D28 de Roth mostraram-se normais e o D15 dessaturado confirmou deutanomalia no caso 1. No segundo caso os testes de comparação mostraram alterações sem significado cromático. O diagnóstico de uma discromatopsia é muito complexo. As autoras destacam a importância de realização de testes de visão cromática complementares ao teste de Ishihara para diagnóstico de uma discromatopsia.The authors describe two cases of hereditary dyschromatopsia and discuss the efficiency of the color vision tests. The patients were disapproved in different federal public examinations because Ishihara's test diagnosed hereditary dyschromatopsia. Ophthalmological evaluation was normal. No symptoms related to dyschromatopsia were presented. Panels D15 and Roth D 28 were normal. Desaturated D 15 showed deuteranomaly in case one. In the second case the comparative color vision tests showed nonspecific disorder. The diagnosis of dyschromatopsia is complex. The authors recommend comparative color vision tests to complement the Ishihara test for a better understanding of the color deficiency.

Síndromes autoinflamatórias hereditárias na faixa etária pediátrica Pediatric hereditary autoinflammatory syndromes

Directory of Open Access Journals (Sweden)

Adriana Almeida Jesus

2010-10-01

Full Text Available OBJETIVO: Descrever as principais síndromes autoinflamatórias hereditárias na faixa etária pediátrica. FONTES DOS DADOS: Foi realizada uma revisão da literatura nas bases de dados PubMed e SciELO, utilizando as palavras-chave "síndromes autoinflamatórias” e "criança”, e incluindo referências bibliográficas relevantes. SÍNTESE DOS DADOS: As principais síndromes autoinflamatórias são causadas por defeitos monogênicos em proteínas da imunidade inata, sendo consideradas imunodeficiências primárias. Elas são caracterizadas clinicamente por sintomas inflamatórios sistêmicos recorrentes ou contínuos e devem ser diferenciadas das doenças infecciosas, autoimunes e outras imunodeficiências primárias. Nesta revisão, foram enfatizadas características epidemiológicas, manifestações clínicas, alterações laboratoriais, prognóstico e terapia das principais síndromes autoinflamatórias: febre familiar do Mediterrâneo; síndrome periódica associada ao receptor de fator de necrose tumoral; criopirinopatias; deficiência de mevalonato-quinase; artrite granulomatosa pediátrica; síndrome de pioderma gangrenoso, artrite piogênica e acne; síndrome de Majeed; e deficiência do antagonista do receptor de interleucina-1. As criopirinopatias discutidas foram: doença inflamatória multissistêmica de início neonatal ou síndrome neurológica, cutânea e articular crônica infantil, síndrome de Muckle-Wells e síndrome autoinflamatória familiar associada ao frio. CONCLUSÕES: É importante que o pediatra reconheça as síndromes autoinflamatórias hereditárias mais prevalentes, pois o encaminhamento ao reumatologista pediátrico pode permitir um diagnóstico precoce e uma instituição de tratamento adequado, possibilitando uma melhora da qualidade de vida dos pacientes.OBJECTIVE: To describe the most prevalent pediatric hereditary autoinflammatory syndromes. SOURCES: A review of the literature including relevant references

How to teach geocomplexity at two opposite levels? The 'Klippen of Cabrières' case study (Hérault, France).

Science.gov (United States)

Giusti, Christian

2014-05-01

The starting point of this essay is a question from a school teacher who came in contact with me via my photo gallery online. His question, "What is the origin of the Roc de Murviel?" actually covers three or four separate problems, and requires to devise simple and specific comparisons in order to help children of 8 years old to understand a bunch of difficult and abstract concepts. But, in contrast, Carboniferous marine sedimentary deposits of the so-called unit "Klippen of Cabrières" are known of geologists worldwide, due to the presence of a Global boundary Stratotype Section and Point (GSSP) located not far from the "Roc de Murviel", the "La Serre" section, where is defined the base of the Carboniferous System, Mississippian Sub-System and Tournaisien Stage. In this case, to remind how the conceptions about the formation of the "Klippen of Cabrières" evolved may serve as an introduction to the explanation of syntectonic sedimentation and to the history of the concept of thrust nappe for the well-trained public as well as academics or engineers not experts in the specificities of regional geology. Difficulty (at least in France) will come from the scarcity of naturalists, a species in danger of extinction, and from the small number of historians concerned by the natural sciences. At the public school, the first method is to decompose the problem into independent issues (Cartesian reductionism) such as: nature and age of the rock? mode of sedimentation? part of an ancient mountain chain? existence as a landform in the current landscape? Concerning the specific question of geological time, because most children of this age do not yet know how to read the time, a second method is to replace the model of the clock (the entire history of the planet Earth reduced to one year) by the metaphor of either the staircase or the ladder, both adapted from the international stratigraphic scale. A third method is to use the concept of "toolbox" for each sub-disciplines or

A consistent approach to assess safety criteria for reactivity initiated accidents

International Nuclear Information System (INIS)

Sartoris, C.; Taisne, A.; Petit, M.; Barre, F.; Marchand, O.

2010-01-01

In the context of more and more demanding reactor managements, the fuel assembly discharge burn-up increases and raises the question of the current safety criteria relevance. In order to assess new safety criteria for reactivity initiated accidents, the IRSN is developing a consistent and original approach to assess safety. This approach is based on: -A thorough understanding of the physical mechanisms involved in each phase (PCMI and post-boiling phases) of the RIA, supported by the interpretation of the experimental database. This experimental data is constituted of global test outcomes, such as CABRI or Nuclear Safety Research Reactor (NSRR) experiments, and analytical program outcomes, such as PATRICIA tests, intending to understand some particular physical phenomena; -The development of computing codes, modelling the physical phenomena. The physical phenomena observed during the tests mentioned above were modelled in the SCANAIR code. SCANAIR is a thermal-mechanical code calculating fuel and clad temperatures and strains during RIA. The CLARIS module is used as a post-calculation tool to evaluate the clad failure risk based on critical flaw depth. These computing codes were validated by global and analytical tests results; -The development of a methodology. The first step of this methodology is the identification of all the parameters affecting the hydride rim depth. Besides, an envelope curve resulting from burst tests giving the hydride rim depth versus oxidation thickness is defined. After that, the critical flaw depth for a given energy pulse is calculated then compared to the hydride rim depth. This methodology results in an energy or enthalpy limit versus burn-up. This approach is planned to be followed for each phase of the RIA. An example of application is presented to evaluate a PCMI limit for a zircaloy-4 cladding UO 2 rod at Hot Zero Power.

Development of Partial Discharging Simulation Test Equipment

Science.gov (United States)

Kai, Xue; Genghua, Liu; Yan, Jia; Ziqi, Chai; Jian, Lu

2017-12-01

In the case of partial discharge training for recruits who lack of on-site work experience, the risk of physical shock and damage of the test equipment may be due to the limited skill level and improper operation by new recruits. Partial discharge simulation tester is the use of simulation technology to achieve partial discharge test process simulation, relatively true reproduction of the local discharge process and results, so that the operator in the classroom will be able to get familiar with and understand the use of the test process and equipment.The teacher sets up the instrument to display different partial discharge waveforms so that the trainees can analyze the test results of different partial discharge types.

Evaluation of the Coat-A-Count 125I fentanyl RIA: Comparison of 125I RIA and GC/MS-SIM for quantification of fentanyl in case urine specimens

International Nuclear Information System (INIS)

Watts, V.W.; Caplan, Y.H.

1990-01-01

The Coat-A-Count solid phase 125 I Fentanyl Radioimmunoassay was evaluated with respect to linearity and precision using equine urine fortified with fentanyl and then compared with a gas chromatographic/mass spectrometric method for quantification of fentanyl in urine. The RIA assay was found to be linear over the urine fentanyl concentration range of 0.25 to 7.5 ng/mL and precise with coefficients of variation (CV) ranging from 9.6 to 19.3%. The RIA calibrators, ranging in fentanyl concentrations from 0.25 to 7.5 ng/mL, and controls, at mean fentanyl concentrations of 0.46 and 1.32 ng/mL, were compared by both the RIA and GC/MS methods. The cross-reactivity with the 125 I RIA test was determined for the fentanyl metabolites, norfentanyl and hydroxyfentanyl, and found to be 5% and 35%, respectively. The illicit fentanyl analogs were found to show significant cross-reactivity, ranging from 20 to 100%. The 125 I RIA was compared to GC/MS quantifications of fentanyl in 35 positive and 20 negative case urine specimens

RailSiTe® (Rail Simulation and Testing

Directory of Open Access Journals (Sweden)

Martin Johne

2016-10-01

Full Text Available RailSiTe® (Rail Simulation and Testing is DLR’s rail simulation and testing laboratory (see Figure 1. It is the implementation of a fully modular concept for the simulation of on-board and trackside control and safety technology. The RailSiTe® laboratory additionally comprises the RailSET (Railway Simulation Environment for Train Drivers and Operators human-factors laboratory, a realistic environment containing a realistic train mockup including 3D simulation.

Simulation and Verificaiton of Flow in Test Methods

DEFF Research Database (Denmark)

Thrane, Lars Nyholm; Szabo, Peter; Geiker, Mette Rica

2005-01-01

Simulations and experimental results of L-box and slump flow test of a self-compacting mortar and a self-compacting concrete are compared. The simulations are based on a single fluid approach and assume an ideal Bingham behavior. It is possible to simulate the experimental results of both tests...

Experimental data report for Test TS-2 reactivity initiated accident test in NSRR with pre-irradiated BWR fuel rod

International Nuclear Information System (INIS)

Nakamura, Takehiko; Yoshinaga, Makio; Sobajima, Makoto; Fujishiro, Toshio; Kobayashi, Shinsho; Yamahara, Takeshi; Sukegawa, Tomohide; Kikuchi, Teruo

1993-02-01

This report presents experimental data for Test TS-2 which was the second test in a series of Reactivity Initiated Accident (RIA) condition test using pre-irradiated BWR fuel rods, performed at the Nuclear Safety Research Reactor (NSRR) in February, 1990. Test fuel rod used in the Test TS-2 was a short sized BWR (7x7) type rod which was fabricated from a commercial rod irradiated at Tsuruga Unit 1 power reactor. The fuel had an initial enrichment of 2.79% and a burnup of 21.3Gwd/tU (bundle average). A pulse irradiation of the test fuel rod was performed under a cooling condition of stagnant water at atmospheric pressure and at ambient temperature which simulated a BWR's cold start-up RIA event. The energy deposition of the fuel rod in this test was evaluated to be 72±5cal/g·fuel (66±5cal/g·fuel in peak fuel enthalpy) and no fuel failure was observed. Descriptions on test conditions, test procedures, transient behavior of the test rod during the pulse irradiation, and, results of pre and post pulse irradiation examinations are described in this report. (author)

Avaliação da memória sob anestesia venosa total

Directory of Open Access Journals (Sweden)

Gulistan Aktas

2013-06-01

Full Text Available JUSTIFICATIVA E OBJETIVOS: Neste estudo, objetivamos avaliar a memória implícita e explícita em pacientes submetidos à cirurgia abdominal sob anestesia venosa total (AVT com propofol e remifentanil, na qual o nível de anestesia foi controlado pelo monitoramento do índice bispectral (BIS. MÉTODO: Anestesia venosa total foi administrada a 60 pacientes adultos para obter níveis de BIS de 40-60. Os pacientes foram randomicamente divididos em três grupos, de acordo com as gravações que ouviram. Os pacientes do grupo categoria (CT ouviram uma fita gravada contendo cinco nomes de animais. Os pacientes do grupo recordar palavras (RP ouviram uma fita gravada contendo cinco palavras de frequência média na língua turca, depois de adaptadas. Os pacientes do grupo controle (GC ouviram os sons do mar até o fim da cirurgia. Duas horas após a cirurgia, os testes foram administrados a cada paciente na sala de recuperação para avaliar a memória. RESULTADOS: Houve uma diferença entre os escores dos grupos CT e GC no Miniexame do Estado Mental (MMSE; todos os escores foram > 20. Os resultados dos testes de categoria e recordar palavras, aplicados para avaliar a memória implícita, não foram estatisticamente diferentes entre os grupos. Não houve evidência de memória implícita em nenhum dos pacientes. Um paciente lembrou-se de ouvir "o som de água" como uma prova de memória explícita. Onze pacientes declararam não ter sonhado. CONCLUSÕES: Apesar de não termos encontrado nenhuma evidência de memória implícita sob anestesia adequada com AVT, um paciente apresentou memória explícita. Embora a profundidade adequada da anestesia fornecida pelo monitoramento do BIS corrobore nossos resultados para a memória implícita, ela não explica os resultados para a memória explícita.

Standard Specification for Solar Simulation for Terrestrial Photovoltaic Testing

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This specification provides means for classifying solar simulators intended for indoor testing of photovoltaic devices (solar cells or modules), according to their spectral match to a reference spectral irradiance, non-uniformity of spatial irradiance, and temporal instability of irradiance. 1.2 Testing of photovoltaic devices may require the use of solar simulators. Test Methods that require specific classification of simulators as defined in this specification include Test Methods E948, E1036, and E1362. 1.3 This standard is applicable to both pulsed and steady state simulators and includes recommended test requirements used for classifying such simulators. 1.4 A solar simulator usually consists of three major components: (1) light source(s) and associated power supply; (2) any optics and filters required to modify the output beam to meet the classification requirements in Section 4; and (3) the necessary controls to operate the simulator, adjust irradiance, etc. 1.5 A light source that does not mee...

Finite element simulations of two rock mechanics tests

International Nuclear Information System (INIS)

Dahlke, H.J.; Lott, S.A.

1986-04-01

Rock mechanics tests are performed to determine in situ stress conditions and material properties of an underground rock mass. To design stable underground facilities for the permanent storage of high-level nuclear waste, determination of these properties and conditions is a necessary first step. However, before a test and its associated equipment can be designed, the engineer needs to know the range of expected values to be measured by the instruments. Sensitivity studies by means of finite element simulations are employed in this preliminary design phase to evaluate the pertinent parameters and their effects on the proposed measurements. The simulations, of two typical rock mechanics tests, the plate bearing test and the flat-jack test, by means of the finite element analysis, are described. The plate bearing test is used to determine the rock mass deformation modulus. The flat-jack test is used to determine the in situ stress conditions of the host rock. For the plate bearing test, two finite element models are used to simulate the classic problem of a load on an elastic half space and the actual problem of a plate bearing test in an underground tunnel of circular cross section. For the flat-jack simulation, a single finite element model is used to simulate both horizontal and vertical slots. Results will be compared to closed-form solutions available in the literature

Simulating lightning tests to radar system

NARCIS (Netherlands)

Blaj, M.A.; Buesink, Frederik Johannes Karel; Leferink, Frank Bernardus Johannes

2010-01-01

The risk of destruction due to lightning makes simulating the effects of lightning strikes a necessity. We modeled a radar enclosure and simulated the effect of a lightning strike. The results have been validated using full threat lightning current tests.

Complex paraclinoidal and giant cavernous aneurysms: importance of preoperative evaluation with temporary balloon occlusion test and SPECT Aneurismas paraclinoideos complexos e cavernosos gigantes: importância da avaliação pré-operatória com teste de oclusão temporária com balão e SPECT

Directory of Open Access Journals (Sweden)

Antônio Aversa do Souto

2006-09-01

Full Text Available In the treatment of complex paraclinoidal and giant cavernous aneurysms, preservation of the patency of the internal carotid artery (ICA is not always possible, and therapeutic occlusion of the carotid is still an important option for their management. A complete preoperative evaluation of the carotid reserve circulation, including the use of temporary balloon occlusion test and single photon emission computerized tomography (SPECT should be included in the current paradigms of paraclinoidal and intracavernous aneurysms management. We present a series of fifteen patients with sixteen giant or complex carotid cavernous or ophthalmic aneurysms that were treated following a protocol for our preoperative decision-making analysis. Extracranial to intracranial saphenous vein bypass was reserved to the cases where carotid occlusion would be associated with high risk of ischemic complications and was performed in three patients. Besides the difficulties in dealing with those complex aneurysms, good clinical outcome was possible in our experience with the designed paradigm.No tratamento de aneurismas paraclinoideos complexos e cavernosos gigantes, a preservação da patência vascular nem sempre é possível, e a oclusão terapêutica da carótida ainda é uma opção importante no seu manejo. Uma avaliação pré-operatória completa da reserva circulatória carotídea, incluindo o uso do teste de oclusão temporária por balão associado à tomografia computadorizada por emissão de fóton único (SPECT podem ser de grande utilidade para definir a opção terapêutica a ser adotada. Nós apresentamos uma série de quinze pacientes com dezesseis aneurismas complexos ou gigantes do segmento oftálmico e cavernoso da artéria carótida, que foram tratados de acordo com determinado protocolo de investigação pré-operatória. Anastomose com enxerto de veia safena entre a carótida extra e intracraniana foi reservada para os casos em que a oclusão carot

História e psicologia em Henri Berr

OpenAIRE

Waeny, Maria Fernanda Costa

2017-01-01

O artigo aborda algumas das idéias de Henri Berr; trata de sua proposta em história, especialmente no que ela se opõe à filosofia da história e à história alemãs; e examina como esta concepção de história à la francesa introduz a psicologia nas pesquisas em história e inaugura a psicologia histórica.Palavras-chave: História da Psicologia; Psicologia Histórica; História das Ciências Humanas; História das Idéias; Annales

As teorias da história e a história ensinada no ensino fundamental

Directory of Open Access Journals (Sweden)

Lia Machado Fiuza Fialho

2017-02-01

Full Text Available Resumo: Objetiva discutir as interfaces das teorias da História e a História ensinada no ensino fundamental, com ênfase na “alfabetização histórica” no século XXI. Como metodologia de pesquisa utilizou-se grupo focal, com 21 pesquisadores e professores que atuavam no campo do Ensino de História e História da Educação. Constatou-se que o ensino no século XXI deve propiciar a aprendizagem de maneira contextualizada, relacionando a pessoa, o tempo e o espaço, em uma perspectiva de produção e transformação da sociedade, na qual o aluno é concebido como sujeito histórico inserido no âmbito dialógico-crítico, tendo o professor como um mediador. Palavras-chave: Ensino. História. Correntes teóricas.

Conceptual design for simulator of irradiation test reactors

International Nuclear Information System (INIS)

Takemoto, Noriyuki; Ohto, Tsutomu; Magome, Hirokatsu; Izumo, Hironobu; Hori, Naohiko

2012-03-01

A simulator of irradiation test reactors has been developed since JFY 2010 for understanding reactor behavior and for upskilling in order to utilize a nuclear human resource development (HRD) and to promote partnership with developing countries which have a plan to introduce nuclear power plant. The simulator is designed based on the JMTR, one of the irradiation test reactors, and it simulates operation, irradiation tests and various kinds of accidents caused by the reactor and irradiation facility. The development of the simulator is sponsored by the Japanese government as one of the specialized projects of advanced research infrastructure in order to promote basic as well as applied researches. The training using the simulator will be started for the nuclear HRD from JFY 2012. This report summarizes the result of the conceptual design of the simulator in JFY 2010. (author)

Estudo de correlação entre provas funcionais respiratórias e o teste de caminhada de seis minutos em pacientes portadores de doença pulmonar obstrutiva crônica

Directory of Open Access Journals (Sweden)

RODRIGUES SÉRGIO LEITE

2002-01-01

Full Text Available Introdução: A espirometria e a gasometria são largamente utilizadas na estimativa da limitação ventilatória e do prognóstico de pacientes portadores de doença pulmonar obstrutiva crônica. Entretanto, testes físicos funcionais, como o teste de caminhada de seis minutos (Tc6, têm surgido como complemento na avaliação dinâmica de portadores de doença pulmonar obstrutiva crônica. Objetivo: Determinar as correlações entre as provas funcionais respiratórias e o teste de caminhada de seis minutos em portadores de DPOC. Pacientes e métodos: 45 pacientes foram submetidos à coleta de história clínica e a exame físico completo realizado pela equipe médica do Serviço de Pneumologia do Hospital Universitário de Brasília. Em seguida, foi realizada a avaliação das variáveis espirométricas, gasométricas, das pressões respiratórias e o teste de caminhada de seis minutos (Tc6. Resultados: Observaram-se correlações positivas estatisticamente significativas (p < 0,05 das variáveis VEF1, PaO2, SpO2 e Pe máx em relação ao teste de caminhada de seis minutos. Conclusões: O teste de caminhada de seis minutos correlacionou-se de forma significativa (p < 0,05 e positiva e pode ser utilizado como instrumento alternativo na avaliação funcional do paciente portador de DPOC.

2003 RIA R AND D WORKSHOP.

Energy Technology Data Exchange (ETDEWEB)

OZAKI, S.ET AL.

2003-08-26

The 2003 RIA R&D Workshop was held on August 26-28, 2003 at the Four Points Sheraton Hotel in Bethesda, Maryland. This Workshop was chaired by Satoshi Ozaki of BNL and sponsored by the Nuclear Physics Division of DOE, with the help of Oak Ridge Institute for Science and Education (ORISE). The purpose of this workshop was to understand the present status of R&D efforts for RIA, to evaluate the needs for further R&D, and to identify opportunities for international collaborations. The workshop examined and documented the current pre-conceptual design for RIA, identifying areas where decisions on technical options remain. The status of the current RIA R&D program was documented, recognizing areas where efforts were needed in light of what had been learned. The ongoing and planned R&D activities for operating and planned rare-isotope facilities were presented, enabling the workshop to be a venue to develop coordinated R&D efforts of mutual benefit to U.S. and international efforts. The scientific program for the first day (August 26, 2003) consisted mostly of invited talks presented by major research groups involved in RIA and other RI beam facilities. The talks included those covering: Science of RIA and the RIA Facility Performance Requirements; The Reference RIA Facility Pre-CDR design that was used for the NSAC cost exercise (M. Harrison Sub-Panel) in January 2001; New or latest perspectives on the RIA design at ANL & MSU; and RI Beam facility plans and overview of the R&D activities at overseas laboratories. The second day (August 27, 2003) was devoted to contributed talks on continuing R&D, including that which had been supported by DOE RIA R&D funds. The third day (August 28, 2003) began with open panel discussions in the morning, including further input from participants. The panel members discussed the present status of the RIA planning and R&D needs in a closed session for the rest of the day, and then worked on report planning and writing. This Workshop

Distúrbios de memória em pacientes epilépticos

Directory of Open Access Journals (Sweden)

STELLA FLORINDO

1999-01-01

Full Text Available O autor estudou distúrbios de memória em pacientes epilépticos com crises parciais complexas (CPC, com os objetivos de: 1 identificar estes distúrbios; e 2 comparar os resultados dos pacientes com os dos controles. Foram estudados 50 pacientes adultos e 20 sujeitos sem enfermidades neuropsiquiátricas. Os métodos consistiram em: 1 investigação da atividade mnemônica através do Teste de Memória de Wechsler (subtestes: Armazenamento e Recuperação, Memória Recente e Memória Imediata; e 2 comparação entre os resultados de ambos os grupos. 3 associação entre SPECT Cerebral e atividade mnemônica. Nos três subtestes, os pacientes apresentaram desempenho cognitivo significativamente inferior ao dos controles (p <0,05. Constatou-se a associação entre hipofluxo em região temporal esquerda e distúrbio da memória nos três subtestes. Concluiu-se que há associação entre CPC e distúrbios da atividade mnemônica.

Automating the simulator testing and data collection process

Energy Technology Data Exchange (ETDEWEB)

Magi, T.; Dimitri-Hakim, R. [L-3 Communications MAPPS Inc., Montreal, Quebec (Canada)

2012-07-01

Scenario-based training is a key process in the use of Full Scope Simulators (FSS) for operator training. Scenario-based training can be defined as any set of simulated plant operations performed with a specific training objective in mind. In order to meet this training objective, the ANSI/ANS-3.5-2009 standard requires that certain simulator training scenarios be tested to ensure that they reproduce the expected plant responses, that all plant procedures can be followed, and that scenario-based training objectives can be met. While malfunction testing provided a narrow view of the simulator performance revolving around the malfunction itself, scenario testing provides a broader, overall view. The concept of instructor validation of simulator scenarios to be used for training and evaluation, and oversight of simulator performance during the validation process, work hand-in-hand. This is where Scenario-Based Testing comes into play. With the description of Scenario-Based Testing (SBT) within Nuclear Energy Institute NEI 09-09 white paper and within the ANSI/ANS-3.5-2009 standard, the industry now has a way forward that reduces the regulatory uncertainty. Together, scenario-based testing and scenario-based training combine to produce better simulators which in turn can be used to more effectively and efficiently train new and existing power plant operators. However, they also impose a significant data gathering and analysis burden on FSS users. L-3 MAPPS Orchid Instructor Station (Orchid IS) facilitates this data gathering and analysis by providing features that automate this process with a simple, centralized, easy to use interface. (author)

Memória e cidadania nos acervos de história oral e mídia digital

OpenAIRE

Goulart, Elias Estevão; Perazzo, Priscila Ferreira; Lemos, Vilma

2010-01-01

Este texto tem como proposta discutir a importância da constituição de acervos de história oral, levando em consideração a difusão da memória e o exercício da cidadania a partir dela, bem como as relações de poder envolvidas nesse processo. As técnicas de história oral possibilitam a organização de um acervo de relatos de história de vida que, no seu conjunto, levam à recuperação da identidade coletiva e da memória da comunidade. São os sentimentos de pertencimento a um grupo, garantindo por ...

Memórias de uma história de um leitor

Directory of Open Access Journals (Sweden)

José Roberto Andrade Féres

2014-07-01

Full Text Available http://dx.doi.org/10.5007/1807-9288.2014v10n1p116 Entre histórias e estórias, entre origens e a “quimera da origem” (Michel Foucault, entre memórias e esquecimentos, entre arquivar e deletar, entre formatar e transformar, entre livros e e-books, entre leitores e leitores de e-books, entre palimpsestos e touchscreens, entre ensaio e relato, entre o que falta e o que excede, entre o que se veste com letras e o que se despe literalmente – este texto: trazendo à lembrança Peter Stallybrass (sobretudo “A vida social das coisas” e “O casaco de Marx”, palavras que buscam tratar as pessoas como coisas e as coisas como pessoas, biografando alguns leitores a partir da biografia de um leitor de e-books, e vice-versa.

2003 RIA R AND D WORKSHOP

International Nuclear Information System (INIS)

OZAKI, S.

2003-01-01

The 2003 RIA R and D Workshop was held on August 26-28, 2003 at the Four Points Sheraton Hotel in Bethesda, Maryland. This Workshop was chaired by Satoshi Ozaki of BNL and sponsored by the Nuclear Physics Division of DOE, with the help of Oak Ridge Institute for Science and Education (ORISE). The purpose of this workshop was to understand the present status of R and D efforts for RIA, to evaluate the needs for further R and D, and to identify opportunities for international collaborations. The workshop examined and documented the current pre-conceptual design for RIA, identifying areas where decisions on technical options remain. The status of the current RIA R and D program was documented, recognizing areas where efforts were needed in light of what had been learned. The ongoing and planned R and D activities for operating and planned rare-isotope facilities were presented, enabling the workshop to be a venue to develop coordinated R and D efforts of mutual benefit to U.S. and international efforts. The scientific program for the first day (August 26, 2003) consisted mostly of invited talks presented by major research groups involved in RIA and other RI beam facilities. The talks included those covering: Science of RIA and the RIA Facility Performance Requirements; The Reference RIA Facility Pre-CDR design that was used for the NSAC cost exercise (M. Harrison Sub-Panel) in January 2001; New or latest perspectives on the RIA design at ANL and MSU; and RI Beam facility plans and overview of the R and D activities at overseas laboratories. The second day (August 27, 2003) was devoted to contributed talks on continuing R and D, including that which had been supported by DOE RIA R and D funds. The third day (August 28, 2003) began with open panel discussions in the morning, including further input from participants. The panel members discussed the present status of the RIA planning and R and D needs in a closed session for the rest of the day, and then worked on report

Cyber-Physical Energy Systems Modeling, Test Specification, and Co-Simulation Based Testing

DEFF Research Database (Denmark)

van der Meer, A. A.; Palensky, P.; Heussen, Kai

2017-01-01

The gradual deployment of intelligent and coordinated devices in the electrical power system needs careful investigation of the interactions between the various domains involved. Especially due to the coupling between ICT and power systems a holistic approach for testing and validating is required....... Taking existing (quasi-) standardised smart grid system and test specification methods as a starting point, we are developing a holistic testing and validation approach that allows a very flexible way of assessing the system level aspects by various types of experiments (including virtual, real......, and mixed lab settings). This paper describes the formal holistic test case specification method and applies it to a particular co-simulation experimental setup. The various building blocks of such a simulation (i.e., FMI, mosaik, domain-specific simulation federates) are covered in more detail...

RIA Quick, AUSRIA II-125, AUSAB. Comparative study on isolated and simultaneous radioimmunoassay of hepatitis B surface antigen and antibodies

Energy Technology Data Exchange (ETDEWEB)

Kselikova, M; Urbankova, J [Institut fuer Haematologie und Bluttransfusion, Prag (Czechoslovakia)

1983-01-01

The surface antigen of hepatitis B (HBsAg) and the antibodies against HBsAg can be determined separately by the radioimmunoassay (RIA) test kits AUSRIA II-125 and AUSAB, respectively. Using the test kit RIA Quick (IMMUNO, Wien) it is possible to perform both the determinations in one preparation simultaneously. The sensitivity of RIA Quick for HBsAg corresponds to that of AUSRIA II-125 and for HBsAB it is considerably lower than that of AUSAB. RIA Quick is of excellent technical design and is by a quarter cheaper than the kits for isolated determination of HBsAg and HBsAb.

Test requirements for the integral effect test to simulate Korean PWR plants

Energy Technology Data Exchange (ETDEWEB)

Song, Chul Hwa; Park, C. K.; Lee, S. J.; Kwon, T. S.; Yun, B. J.; Chung, M. K

2001-02-01

In this report, the test requirements are described for the design of the integral effect test facility to simulate Korean PWR plants. Since the integral effect test facility should be designed so as to simulate various thermal hydraulic phenomena, as closely as possible, to be occurred in real plants during operation or anticipated transients, the design and operational characteristics of the reference plants (Korean Standard Nuclear Plant and Korean Next Generation Reactor)were analyzed in order to draw major components, systems, and functions to be satisfied or simulated in the test facility. The test matrix is set up by considering major safety concerns of interest and the test objectives to confirm and enhance the safety of the plants. And the analysis and prioritization of the test matrix leads to the general design requirements of the test facility. Based on the general design requirements, the design criteria is set up for the basic and detailed design of the test facility. And finally it is drawn the design requirements specific to the fluid system and measurement system of the test facility. The test requirements in this report will be used as a guideline to the scaling analysis and basic design of the test facility. The test matrix specified in this report can be modified in the stage of main testing by considering the needs of experiments and circumstances at that time.

Test requirements for the integral effect test to simulate Korean PWR plants

International Nuclear Information System (INIS)

Song, Chul Hwa; Park, C. K.; Lee, S. J.; Kwon, T. S.; Yun, B. J.; Chung, M. K.

2001-02-01

In this report, the test requirements are described for the design of the integral effect test facility to simulate Korean PWR plants. Since the integral effect test facility should be designed so as to simulate various thermal hydraulic phenomena, as closely as possible, to be occurred in real plants during operation or anticipated transients, the design and operational characteristics of the reference plants (Korean Standard Nuclear Plant and Korean Next Generation Reactor)were analyzed in order to draw major components, systems, and functions to be satisfied or simulated in the test facility. The test matrix is set up by considering major safety concerns of interest and the test objectives to confirm and enhance the safety of the plants. And the analysis and prioritization of the test matrix leads to the general design requirements of the test facility. Based on the general design requirements, the design criteria is set up for the basic and detailed design of the test facility. And finally it is drawn the design requirements specific to the fluid system and measurement system of the test facility. The test requirements in this report will be used as a guideline to the scaling analysis and basic design of the test facility. The test matrix specified in this report can be modified in the stage of main testing by considering the needs of experiments and circumstances at that time

Determination of triiodothyronine using RIA-Mat T3 kit

International Nuclear Information System (INIS)

Hara, Masao

1975-01-01

A RIA-Mat T 3 kit was used for an in vitro measurement of triiodothyronine in serum. A resin strip was utilized to absorb free triiodothyronine after the serum was incubated with antibody against triiodothyronine. This test was easy to manipulate and the reproducibility test with same sera, dilution test, and recovery test were also satisfactory. The normal range of triiodothyronine determined with this test kit was 119 +- 40 ng/dl using 50 test sera. Ninety sera with various thyroid diseases were also determined. (auth.)

Histórias divergentes na intelectualidade docente: trajetórias formativas nas memórias de professoras do ensino municipal de São Paulo (1964-1985

Directory of Open Access Journals (Sweden)

Helenice Ciampi

2017-07-01

Full Text Available Com base na metodologia da história oral temática,analisa-se no artigo uma entrevista simultânea, na qual três docentes relatam suas trajetórias familiares, escolares e acadêmicas. Analisa-se o processo de sua formação como professoras, a partir do final dos anos 1960, e as posições políticasque assumiram no presente,2012, em relação à educação e à escola municipal paulistana no período da ditadura civil-militar no Brasil (1964-1985. O principal objetivo é mostrar que suas memórias expressam divergências individuais e coletivas e que existem outras formas de expressão da intelectualidade docente, as quais emergem das tensões econtradiçõesvivenciadas em suas trajetórias formativas e não das prescriçõespolíticas e acadêmicas educacionaisque silenciamoutras vozes, memórias e saberes.

Flow analysis of HANARO flow simulated test facility

International Nuclear Information System (INIS)

Park, Yong-Chul; Cho, Yeong-Garp; Wu, Jong-Sub; Jun, Byung-Jin

2002-01-01

The HANARO, a multi-purpose research reactor of 30 MWth open-tank-in-pool type, has been under normal operation since its initial critical in February, 1995. Many experiments should be safely performed to activate the utilization of the NANARO. A flow simulated test facility is being developed for the endurance test of reactivity control units for extended life times and the verification of structural integrity of those experimental facilities prior to loading in the HANARO. This test facility is composed of three major parts; a half-core structure assembly, flow circulation system and support system. The half-core structure assembly is composed of plenum, grid plate, core channel with flow tubes, chimney and dummy pool. The flow channels are to be filled with flow orifices to simulate core channels. This test facility must simulate similar flow characteristics to the HANARO. This paper, therefore, describes an analytical analysis to study the flow behavior of the test facility. The computational flow analysis has been performed for the verification of flow structure and similarity of this test facility assuming that flow rates and pressure differences of the core channel are constant. The shapes of flow orifices were determined by the trial and error method based on the design requirements of core channel. The computer analysis program with standard k - ε turbulence model was applied to three-dimensional analysis. The results of flow simulation showed a similar flow characteristic with that of the HANARO and satisfied the design requirements of this test facility. The shape of flow orifices used in this numerical simulation can be adapted for manufacturing requirements. The flow rate and the pressure difference through core channel proved by this simulation can be used as the design requirements of the flow system. The analysis results will be verified with the results of the flow test after construction of the flow system. (author)

Automated testing and reverification for training simulators using SATAR

International Nuclear Information System (INIS)

Charles, R.D.; Gaddy, C.D.; Nargarkar, A.; Colley, R.

1990-01-01

This paper reports that simulators used to train nuclear power plant operators must be recertified periodically to ensure fidelity for training (10 CFR 55.45). The objective of the Simulator Automated Testing and Reverification (SATAR) project was to develop software to reverify dynamic simulator performance automatically. The software resides in a standard configuration personal computer and in the simulator computer; the two computers are linked via serial ports. SATAR will automatically run performance tests, collect and analyze data, and compare data with baseline performance data. With SATAR, support from operations and simulator support personnel can be reduced greatly, and the repeatability of performance tests can be improved

The Application of Voltage Transformer Simulator in Electrical Test Training

Science.gov (United States)

Li, Nan; Zhang, Jun; Chai, Ziqi; Wang, Jingpeng; Yang, Baowei

2018-02-01

The voltage transformer test is an important means to monitor its operating state. The accuracy and reliability of the test data is directly related to the test skill level of the operator. However, the risk of test instruments damage, equipment being tested damage and electric shock in operator is caused by improper operation when training the transformer test. In this paper, a simulation device of voltage transformer is set up, and a simulation model is built for the most common 500kV capacitor voltage transformer (CVT), the simulation model can realize several test items of CVT by combing with teaching guidance platform, simulation instrument, complete set of system software and auxiliary equipment in Changchun. Many successful applications show that the simulation device has good practical value and wide application prospect.

Testability, Test Automation and Test Driven Development for the Trick Simulation Toolkit

Science.gov (United States)

Penn, John

2014-01-01

This paper describes the adoption of a Test Driven Development approach and a Continuous Integration System in the development of the Trick Simulation Toolkit, a generic simulation development environment for creating high fidelity training and engineering simulations at the NASA Johnson Space Center and many other NASA facilities. It describes the approach, and the significant benefits seen, such as fast, thorough and clear test feedback every time code is checked into the code repository. It also describes an approach that encourages development of code that is testable and adaptable.

Construindo a História dos Bairros: Um Diálogo Entre Memória e Educação

Directory of Open Access Journals (Sweden)

Tiago Pires

2014-10-01

Full Text Available http://dx.doi.org/10.5007/1807-0221.2014v11n17p Na contemporaneidade, a grande produção de informação faz com que os saberes e memórias do passado sejam substituídos pela constante inovação midiática, pautada em relações voláteis típicas da pós-modernidade. Durante grande parte da história do Brasil, a valorização de saberes, memórias e lugares somente ocorreu quando esses eram referentes às grandes personalidades, na maioria das vezes pertencentes à elite econômica. Em meio a esse contexto, desenvolvemos um projeto de pesquisa que objetivava resgatar as memórias, histórias e culinárias de bairros periféricos de Ouro Preto, Minas Gerais, Brasil. Visando valorizar esses saberes e sujeitos, iniciamos um processo de investigação, pautado na metodologia da história oral e do ensino de História por projetos, envolvendo os alunos da rede pública, bem como professores e historiadores. A pesquisa foi desenvolvida entre 2008 e 2011, resultando na construção de um livro com fins didático-pedagógicos, intitulado “Saramenha: memórias, histórias e culinária”.

simulate_CAT: A Computer Program for Post-Hoc Simulation for Computerized Adaptive Testing

Directory of Open Access Journals (Sweden)

İlker Kalender

2015-06-01

Full Text Available This paper presents a computer software developed by the author. The software conducts post-hoc simulations for computerized adaptive testing based on real responses of examinees to paper and pencil tests under different parameters that can be defined by user. In this paper, short information is given about post-hoc simulations. After that, the working principle of the software is provided and a sample simulation with required input files is shown. And last, output files are described

Leituras de operárias

Directory of Open Access Journals (Sweden)

Betty Mindlin

2008-03-01

Full Text Available Defensora de causas sociais, paladina poética contra injustiças e desigualdade, Ecléa Bosi em seu livro Cultura Popular e Cultura de Massa: Leituras de Operárias, pesquisa as leituras de cerca de 50 operárias, procurando ver que acesso têm ao imaginário, aos livros, quais as suas condições de vida, como a sociedade industrial as privam da criação artística e literária, apesar de sua sede de conhecimento e de expressão.

Visuospatial Aptitude Testing Differentially Predicts Simulated Surgical Skill.

Science.gov (United States)

Hinchcliff, Emily; Green, Isabel; Destephano, Christopher; Cox, Mary; Smink, Douglas; Kumar, Amanika; Hokenstad, Erik; Bengtson, Joan; Cohen, Sarah

2018-02-05

To determine if visuospatial perception (VSP) testing is correlated to simulated or intraoperative surgical performance as rated by the American College of Graduate Medical Education (ACGME) milestones. Classification II-2 SETTING: Two academic training institutions PARTICIPANTS: 41 residents, including 19 Brigham and Women's Hospital and 22 Mayo Clinic residents from three different specialties (OBGYN, general surgery, urology). Participants underwent three different tests: visuospatial perception testing (VSP), Fundamentals of Laparoscopic Surgery (FLS®) peg transfer, and DaVinci robotic simulation peg transfer. Surgical grading from the ACGME milestones tool was obtained for each participant. Demographic and subject background information was also collected including specialty, year of training, prior experience with simulated skills, and surgical interest. Standard statistical analysis using Student's t test were performed, and correlations were determined using adjusted linear regression models. In univariate analysis, BWH and Mayo training programs differed in both times and overall scores for both FLS® peg transfer and DaVinci robotic simulation peg transfer (p<0.05 for all). Additionally, type of residency training impacted time and overall score on robotic peg transfer. Familiarity with tasks correlated with higher score and faster task completion (p= 0.05 for all except VSP score). There was no difference in VSP scores by program, specialty, or year of training. In adjusted linear regression modeling, VSP testing was correlated only to robotic peg transfer skills (average time p=0.006, overall score p=0.001). Milestones did not correlate to either VSP or surgical simulation testing. VSP score was correlated with robotic simulation skills but not with FLS skills or ACGME milestones. This suggests that the ability of VSP score to predict competence differs between tasks. Therefore, further investigation is required into aptitude testing, especially prior

Aproximações entre história pública e história oral: o caso do Laboratório de História Oral da Univille

Directory of Open Access Journals (Sweden)

Ilanil Coelho

2016-12-01

Full Text Available Neste artigo, construímos uma aproximação teórico-metodológica entre a História Pública (HP e História Oral (HO. O texto encontra-se estruturado em três partes. Na primeira, além de apresentarmos nossa perspectiva conceitual sobre HP, refletimos sobre a historicidade da noção de HP na Inglaterra, nos Estados Unidos e no Brasil, pontuando seus diversos cruzamentos com a HO. Em seguida, com base numa ampla pesquisa documental, perscrutamos os sentidos de História Oral e o papel atribuído ao historiador e ao conhecimento histórico durante a criação do Laboratório de História Oral da Universidade da Região de Joinville (LHO/Univille. Nesse fazer, analisamos como, no início dos anos 1980, esse espaço foi concebido como parte de uma rede de produção de fontes orais que envolvia numerosas instituições de ensino superior do sul do Brasil e, também, entidades internacionais de atuação multilateral, tais como a Organização dos Estados Americanos (OEA e a Secretaria de Cooperação Técnica Internacional do Brasil, subordinada ao então Ministério de Educação e Cultura (SUBIN/MEC. No terceiro e último item, finalizamos o texto tecendo algumas considerações sobre os limites e as possibilidades reflexivas da HP quando articulada à HO e aos recentes debates sobre o papel público do historiador na escrita da História do Tempo Presente.   Palavras-chave: História Pública; História Oral; História do Tempo Presente; LHO/Univille.

Experimental data report for test TS-3 Reactivity Initiated Accident test in the NSRR with pre-irradiated BWR fuel rod

International Nuclear Information System (INIS)

Nakamura, Takehiko; Yoshinaga, Makio; Fujishiro, Toshio; Kobayashi, Shinsho; Yamahara, Takeshi; Sukegawa, Tomohide; Kikuchi, Teruo; Sobajima, Makoto.

1993-09-01

This report presents experimental data for Test TS-3 which was the third test in a series of Reactivity Initiated Accident (RIA) tests using pre-irradiated BWR fuel rods, performed in the Nuclear Safety Research Reactor (NSRR) in September, 1990. Test fuel rod used in the Test TS-3 was a short-sized BWR (7 x 7) type rod which was re-fabricated from a commercial rod irradiated in the Tsuruga Unit 1 power reactor of Japan Atomic Power Co. The fuel had an initial enrichment of 2.79 % and a burnup of 26 Gwd/tU. A pulse irradiation of the test fuel rod was performed under a cooling condition of stagnant water at atmospheric pressure and at ambient temperature which simulated a BWR's cold start-up RIA event. The energy deposition of the fuel rod in this test was evaluated to be 94 ± 4 cal/g · fuel (88 ± 4 cal/g · fuel in peak fuel enthalpy) and no fuel failure was observed. Descriptions on test conditions, test procedures, transient behavior of the test rod during the pulse irradiation, and results of pre-pulse and post-pulse irradiation examinations are described in this report. (author)

Variação temporal no desempenho em testes de memória em pacientes com doença vascular cerebral Temporal variation in memory tests performance in cerebral vascular disease patients

Directory of Open Access Journals (Sweden)

Tania Fernandes Campos

2007-01-01

Full Text Available Buscando adequar a avaliação neuropsicológica à organização temporal do organismo humano, avaliou-se o desempenho em testes de memória em 12 pacientes pós Doença Vascular Cerebral e 12 indivíduos controle, de ambos os sexos, com idade de 45 a 65 anos. Foram aplicados dois testes de memória com estímulos visuais (figuras e dois com estímulos verbais (palavras, em 3 dias consecutivos por semana, às 08:00, 10:00 e 12:00 h na primeira semana e às 14:00 e 16:00 h na seguinte. Os pacientes apresentaram menor número de acertos do que os indivíduos controle em todos os testes aplicados (pThis study intended to investigate the performance in memory tests in order to adequate the neuropsychological evaluation to the temporal order of the human organism. Twelve cerebral vascular accident patients and 12 controls, of both sexes and 45-65 years old were studied. Two memory tests with visual stimuli (pictures and two with verbal stimuli (words were applied three times a day (08:00, 10:00 and 12:00 h during the first week and twice a day (14:00 and 16:00 h in the second week, during three consecutive days in two consecutive weeks. The patients showed lower scores than control subjects in all applied tests (p<0,05. The greater test sensitivity was at 14:00 h for the free recall test and at 16:00 h for recognition tests. According to these results, it is concluded that neuropsychological evaluations should be conducted preferably in the afternoon, as well for the first evaluation as for the re-evaluations.

The 'SURA' fast reactor program

International Nuclear Information System (INIS)

Anon.

1979-01-01

The Commissariat a l'Energie Atomique's SURA program on fast reactor safety consists of two specific testing programs on fastbreeder reactor safety: the Cabri and Scarabee programs. Both Cabri and Scarabee are examples of multinational research collaboration. The CEA and the Karlsruhe Nuclear Research Center are each covering half of the construction costs. Britain, the US and Japan are also due to participate in these experiments. The aim of the programs is to examine the behaviour of fuel in sodium cooled fast reactors. The Cabri program consists of setting off a reactivity accident in a power reactor core which is cooled with liquid sodium, such an accident occurring after a sharp increase in reactivity or as a result of the pump suddenly breaking down without there at the same time being any fall in the control rods. In 1967 the Commissariat a l'Energie Atomique started its Scarabee research program which is trying to analyse the sort of things that can go wrong with fuel cooling systems and what the consequences can be [fr

BWR Full Integral Simulation Test (FIST) Phase II test results and TRAC-BWR model qualification

International Nuclear Information System (INIS)

Sutherland, W.A.; Alamgir, M.; Findlay, J.A.; Hwang, W.S.

1985-10-01

Eight matrix tests were conducted in the FIST Phase I. These tests investigated the large break, small break and steamline break LOCA's, as well as natural circulation and power transients. There are nine tests in Phase II of the FIST program. They include the following LOCA tests: BWR/6 LPCI line break, BWR/6 intermediate size recirculation break, and a BWR/4 large break. Steady state natural circulation tests with feedwater makeup performed at high and low pressure, and at high pressure with HPCS makeup, are included. Simulation of a transient without rod insertion, and with controlled depressurization, was performed. Also included is a simulation of the Peach Bottom turbine trip test. The final two tests simulated a failure to maintain water level during a postulated accident. A FIST program objective is to assess the TRAC code by comparisons with test data. Two post-test predictions made with TRACB04 are compared with Phase II test data in this report. These are for the BWR/6 LPCI line break LOCA, and the Peach Bottom turbine trip test simulation

Pre-flight physical simulation test of HIMES reentry test vehicle

Science.gov (United States)

Kawaguchi, Jun'ichiro; Inatani, Yoshifumi; Yonemoto, Koichi; Hosokawa, Shigeru

ISAS is now developing a small reentry test vehicle, which is 2m long with a 1.5m wing span and weighs about 170 kg, for the purpose of exploring high angle-of-attack aerodynamic attitude control issue in supersonic and hypersonic speed. The flight test, employing 'Rockoon' launch system, is planned as a preliminary design verification for a fully reusable winged rocket named HIMES (Highly Maneuverable Experimental Space) vehicle. This paper describes the results of preflight ground test using a motion table system. This ground system test is called 'physical simulation' aimed at: (1) functional verification of side-jet system, aerodynamic surface actuators, battery and onboard avionics; and (2) guidance and control law evaluation, in total hardware-in-the-loop system. The pressure of side-jet nozzles was measured to provide exact thrust characteristics of reaction control. The dynamics of vehicle motion was calculated in real-time by the ground simulation computer.

Reliability Testing Using the Vehicle Durability Simulator

Science.gov (United States)

2017-11-20

techniques are employed to reduce test and simulation time. Through application of these processes and techniques the reliability characteristics...remote parameter control (RPC) software. The software is specifically designed for the data collection, analysis, and simulation processes outlined in...the selection process for determining the desired runs for simulation . 4.3 Drive File Development. After the data have been reviewed and

Explosive simulants for testing explosive detection systems

Science.gov (United States)

Kury, John W.; Anderson, Brian L.

1999-09-28

Explosives simulants that include non-explosive components are disclosed that facilitate testing of equipment designed to remotely detect explosives. The simulants are non-explosive, non-hazardous materials that can be safely handled without any significant precautions. The simulants imitate real explosives in terms of mass density, effective atomic number, x-ray transmission properties, and physical form, including moldable plastics and emulsions/gels.

Simulation of Particle Fluxes at the DESY-II Test Beam Facility

International Nuclear Information System (INIS)

Schuetz, Anne

2015-05-01

In the course of this Master's thesis ''Simulation of Particle Fluxes at the DESY-II Test Beam Facility'' the test beam generation for the DESY test beam line was studied in detail and simulated with the simulation software SLIC. SLIC uses the Geant4 toolkit for realistic Monte Carlo simulations of particles passing through detector material.After discussing the physics processes relevant for the test beam generation and the principles of the beam generation itself, the software used is introduced together with a description of the functionality of the Geant4 Monte Carlo simulation. The simulation of the test beam line follows the sequence of the test beam generation. Therefore, it starts with the simulation of the beam bunch of the synchrotron accelerator DESY-II, and proceeds step by step with the single test beam line components. An additional benefit of this thesis is the provision of particle flux and trajectory maps, which make fluxes directly visible by following the particle tracks through the simulated beam line. These maps allow us to see each of the test beam line components, because flux rates and directions change rapidly at these points. They will also guide the decision for placements of future test beam line components and measurement equipment.In the end, the beam energy and its spread, and the beam rate of the final test beam in the test beam area were studied in the simulation, so that the results can be compared to the measured beam parameters. The test beam simulation of this Master's thesis will serve as a key input for future test beam line improvements.

Review of RIA and LOCA criteria for WWER fuel

International Nuclear Information System (INIS)

Hozer, Z.

2006-01-01

The RIA and LOCA fuel safety criteria are under revision in the international community of fuel suppliers, authorities and research organizations. The main criteria will be reviewed in the paper for WWER fuel. Experimental data on the fuel failure behaviour under reactivity-initiated accident (RIA) conditions produced in the last decade in French and Japanese test reactors indicated low failure enthalpy for high burnup fuel compared to fresh fuel. However the high burnup was not the only phenomenon influencing the fuel failure. The oxide scale on the external surface of the fuel rod, hydrogen content of the Zr cladding and the local hydriding seemed also be responsible for the failure at low enthalpy. Furthermore differences have been found between Western design fuel and Russian type WWER fuel. The burnup dependence of fuel failure for WWER fuel was found much less, probably due to the low oxidation during normal operational conditions compared to other PWRs. The recently published Vitanza and KAERI correlations for RIA failure enthalpy have been applied to 23 WWER tests. Experimental data from Russian IGR and BIGR reactors have been used. The calculations have shown that both burnup and cladding oxidation effects must be considered, however the pulse width dependence of failure enthalpy has not been confirmed. During loss of coolant accidents (LOCA) the peak cladding temperature and local oxidation criteria have to be met. The oxidation criterion is under discussion today in many laboratories. The AEKI carried out several experimental series with Zr1%Nb cladding used in WWER reactors. The paper will describe the main results of the tests and present the limit for ductile-brittle transition derived from ring compression test. The behaviour of Zr1%Nb (E110) and Zircaloy-4 claddings under LOCA conditions will be compared as well. (author)

Numerical simulation of small scale soft impact tests

International Nuclear Information System (INIS)

Varpasuo, Pentti

2008-01-01

This paper describes the small scale soft missile impact tests. The purpose of the test program is to provide data for the calibration of the numerical simulation models for impact simulation. In the experiments, both dry and fluid filled missiles are used. The tests with fluid filled missiles investigate the release speed and the droplet size of the fluid release. This data is important in quantifying the fire hazard of flammable liquid after the release. The spray release velocity and droplet size are also input data for analytical and numerical simulation of the liquid spread in the impact. The behaviour of the impact target is the second investigative goal of the test program. The response of reinforced and pre-stressed concrete walls is studied with the aid of displacement and strain monitoring. (authors)

Prototyping a robotic dental testing simulator.

Science.gov (United States)

Alemzadeh, K; Hyde, R A; Gao, J

2007-05-01

A parallel robot based on the Stewart platform is being developed to simulate jaw motion and investigate its effect on jaw function to test the wearing away of dental components such as individual teeth, crowns, bridges, full set of dentures, and implant-supported overdentures by controlling chewing motion. The current paper only describes the comparison between an alternative configuration proposed by Xu and the Stewart platform configuration. The Stewart platform was chosen as an ideal structure for simulating human mastication as it is easily assembled, has high rigidity, high load-carrying capacity, and accurate positioning capability. The kinematics and singularities of the Stewart platform have been analysed and software developed to (a) test the control algorithms/strategy of muscle movement for the six degree of freedom of mastication cycle and (b) simulate and observe various design options to be able to make the best judgement in product development. The human replica skull has been analysed and reverse engineered with further simplification before integration with the Stewart platform computer-aided design (CAD) to develop the robotic dental testing simulator. Assembly modelling of the reproduced skull was critically analysed for good occlusion in CAD environment. A pulse-width modulation (PWM) circuit plus interface was built to control position and speed of the chosen actuators. A computer numerical control (CNC) machine and wire-electro-discharge machining (wire EDM) were used to manufacture the critical parts such as lower mandible, upper maxilla, and universal joints.

Reformas tributária e previdenciária e a economia brasileira no longo prazo

Directory of Open Access Journals (Sweden)

Vladimir Kühl Teles

2006-03-01

Full Text Available O presente artigo busca simular o efeito das reformas tributária e previdenciária sobre variáveis chave da economia brasileira no longo prazo. Para tanto, um modelo de equilíbrio geral computável de gerações superpostas sob a especificação de um modelo de crescimento endógeno à la Lucas (1988 é utilizado. Dentre os principais resultados pode-se destacar que as reformas por si só não são capazes de melhorar a performance de variáveis como taxa de juros e crescimento no longo-prazo, entretanto, ao criar oportunidades para diminuir a dívida pública e aumentar o investimento em educação, tornam-se fundamentais para uma melhoria em tais variáveis.The paper simulates the effects of tax and social security reforms on the main variables of the Brazilian Economy in the long run. For that matter a computable general equilibrium model of overlapping generations à la Lucas (1988 is employed. The main results are that the reforms in themselves are not capable of affecting the performance of the interest rate and the long run growth rate of the economy. However, as long as they make it possible to reduce the public debt and to increase the investment in education, they become important for the improvement of those variables.

Filho de peixe sabe nadar: história e estórias com objetos

Directory of Open Access Journals (Sweden)

Ana Catarina Nunes

2016-04-01

Full Text Available O presente artigo apresenta e discute o projeto Filho de Peixe Sabe Nadar, desenvolvido no Museu Marítimo de Ílhavo entre 2010 e 2011, e dirigido a alunos do 4.º ano do 1.º ciclo do Ensino Básico do Município de Ílhavo. Com o objetivo de dar a conhecer a história e as memórias da pesca do bacalhau à linha em dóris de um só homem e em grandes navios de arrasto, pilar temático do Museu Marítimo de Ílhavo, o projeto visou, ainda, estreitar os laços entre gerações e entre a comunidade, procurando incentivar as crianças na procura de antepassados ligados a esta atividade. Ao longo do texto são descritas as várias etapas do projeto, assim como a contextualização teórica que as fundamentam. Através deste projeto, as crianças da comunidade local tiveram oportunidade de confrontar os conhecimentos adquiridos durante uma visita ao Museu Marítimo de Ílhavo e ao Navio Museu Santo André, com as experiências e testemunhos transmitidos pelos familiares ou amigos que entrevistaram e dos quais recolheram objetos que materializam essas vivências. Herança da comunidade ilhavense, a pesca do bacalhau pôde ser vista de forma distinta, com um contacto direto das crianças com os personagens reais da história da Grande Pesca e com os objetos que lhe estão associados. É a partir destes objetos que surgem as estórias desses mesmos personagens que, juntas constroem as memórias da pesca do bacalhau.

Results of applications of DISKOT system and of RIA determination of progesterone

International Nuclear Information System (INIS)

Beranek, J.

1989-01-01

Milk for progesterone determination was taken from cows picked out for insemination, cows following insemination and cows with reproduction disorders. The samples were taken in test tubes containing potassium dichromate. Progesterone was determined by RIA of skimmed milk and the results were transmitted to the DISKOT system in the data processing centre. The use of the DISKOT system output and the monitoring of progesterone in milk by the RIA laboratory improved reproduction indexes of the herd under study. (E.J.). 2 tabs

Geotechnical Tests on Asteroid Simulant Orgueil

Science.gov (United States)

Garcia, Alexander D'marco

2017-01-01

In the last 100 years, the global population has more than quadrupled to over seven billion people. At the same time, the demand for food and standard of living has been increasing which has amplified the global water use by nearly eight times from approximately 500 to 4000 cu km per yr from 1900 to 2010. With the increasing concern to sustain the growing population on Earth it is necessary to seek other approaches to ensure that our planet will have resources for generations to come. In recent years, the advancement of space travel and technology has allowed the idea of mining asteroids with resources closer to becoming a reality. During the duration of the internship at NASA Kennedy Space Center, several geotechnical tests were conducted on BP-1 lunar simulant and asteroid simulant Orgueil. The tests that were conducted on BP-1 was to practice utilizing the equipment that will be used on the asteroid simulant and the data from those tests will be omitted from report. Understanding the soil mechanics of asteroid simulant Orgueil will help provide basis for future technological advances and prepare scientists for the conditions they may encounter when mining asteroids becomes reality in the distant future. Distinct tests were conducted to determine grain size distribution, unconsolidated density, and maximum density. Once the basic properties are known, the asteroid simulant will be altered to different levels of compaction using a vibrator table to see how compaction affects the density. After different intervals of vibration compaction, a miniature vane shear test will be conducted. Laboratory vane shear testing is a reliable tool to investigate strength anisotropy in the vertical and horizontal directions of a very soft to stiff saturated fine-grained clayey soil. This test will provide us with a rapid determination of the shear strength on the undisturbed compacted regolith. The results of these tests will shed light on how much torque is necessary to drill

Evaluation of the Coat-A-Count sup 125 I fentanyl RIA: Comparison of sup 12 5I RIA and GC/MS-SIM for quantification of fentanyl in case urine specimens

Energy Technology Data Exchange (ETDEWEB)

Watts, V.W.; Caplan, Y.H. (Mesa Police Crime Laboratory, AZ (USA))

1990-09-01

The Coat-A-Count solid phase {sup 125}I Fentanyl Radioimmunoassay was evaluated with respect to linearity and precision using equine urine fortified with fentanyl and then compared with a gas chromatographic/mass spectrometric method for quantification of fentanyl in urine. The RIA assay was found to be linear over the urine fentanyl concentration range of 0.25 to 7.5 ng/mL and precise with coefficients of variation (CV) ranging from 9.6 to 19.3%. The RIA calibrators, ranging in fentanyl concentrations from 0.25 to 7.5 ng/mL, and controls, at mean fentanyl concentrations of 0.46 and 1.32 ng/mL, were compared by both the RIA and GC/MS methods. The cross-reactivity with the {sup 125}I RIA test was determined for the fentanyl metabolites, norfentanyl and hydroxyfentanyl, and found to be 5% and 35%, respectively. The illicit fentanyl analogs were found to show significant cross-reactivity, ranging from 20 to 100%. The {sup 125}I RIA was compared to GC/MS quantifications of fentanyl in 35 positive and 20 negative case urine specimens.

Evaluation of a solid-phase RIA technique and a solid-phase ELISA technique for demonstrating hepatitis-B surface antigen

International Nuclear Information System (INIS)

Vranckx, R.; Cole, J.; Peetermans, M.

1978-01-01

The sensitivities of a solid-phase radioimmunoassay (RIA), a solid-phase enzyme immunoassay (ELISA) and a haemagglutination test (RPHA) for the detection of the hepatitis-B surface antigen (HBsAg) were compared (1) by screening a panel of 300 sera (97 positives and 203 negatives), and (2) by titrating serial dilutions of 10 positive sera. Ninety-seven sera were positive by RIA, 95% were detected by ELISA and 81% were detected by RPHA. In the serial dilutions, the average end-points of the titrations were 0.005ng/ml for RIA, 0.01ng/ml for ELISA and 0.04 ng/ml for RPHA. It can be concluded that the sensitivity of the ELISA test is intermediate between that of the RIA and the RPHA. The ELISA and the RPHA tests seem to be a little more sensitive for the detection of subtype ay than for the detection of subtype ad. (author)

Simulated hail impact testing of photovoltaic solar panels

Science.gov (United States)

Moore, D.; Wilson, A.; Ross, R.

1978-01-01

Techniques used to simulate and study the effect of hail on photovoltaic solar panels are described. Simulated hail stones (frozen ice spheres projected at terminal velocity) or steel balls were applied by air guns, gravity drop, or static loading. Tests with simulated hail and steel balls yielded different results. The impact strength of 10 commercially available flat-plate photovoltaic modules was tested. It was found that none of the six panel designs incorporating clear potting silicone material as the outermost layer remained undamaged by 1-in. simulated hailstones, while a photovoltaic module equipped with a 0.188-in.-thick acrylic cover sheet would be able to withstand the impact of a 2-in.-diameter hailstone.

C peptide and insulin releasing RIA test for the investigation of β cell function in diabetic patients

International Nuclear Information System (INIS)

Shi Ailan; Zhu Chengmo; Wang Qiyu; Wang Ping

1993-01-01

Results of C-peptide releasing RIA test in 15 normals, and 100 diabetes were summarized and compared with glucose tolerance test and serum insulin for investigating the characteristics in different types of diabetes and evaluating the functional state of islet β cell. In 36 cases of IDDM the fasting blood sugar was significantly increased, and further elevated after eating of bread, but its peak time delay in 2 hours (normalin 1 hour). The level of basal C-peptide is very low, but shows slightly weak on no response after bread stimulating test, all of this denotes that β cell function of islets severely injured. The increasing of fasting blood sugar in 64 cases of NIDDM was lower than those of IDDM. Fasting C-peptide and insulin was normal or increased, their peak value increased after bread stimulation with peak time delayed also at 2 hours. Above results demonstrated that the function of islets B cell decreased but not fully deprived. It is concluded that C-peptide and insulin stimulating test, together with OGTT can accurately assess the islets β cell function, and also have important significance in the pathogenesis, classification and staging, prognostic evaluation and monitoring of therapeutic effects in diabetes

Biblioteca universitária, escolar e comunitária: o caso da biblioteca comunitária “Professora Ebe Alves da Silva” do IFMG

Directory of Open Access Journals (Sweden)

Helena Maria Tarchi Crivellari

2015-12-01

Full Text Available A Expansão da Rede Federal de Educação Profissional, Científica e Tecnológica ocorrida em 2008, pela lei 11.892, transformou diferentes instituições de ensino técnico federais em Institutos Federais de Educação, Ciência e Tecnologia, que são responsáveis pela educação profissional em diferentes modalidades de ensino, promovendo tanto a educação básica quanto a educação superior. Inseridas nesse contexto estão as bibliotecas dessas instituições, que são, concomitantemente, bibliotecas escolares e universitárias. Com o objetivo de demonstrar o papel dessas bibliotecas, motivado pelo questionamento sobre a possibilidade de convivência desses tipos de bibliotecas em um mesmo espaço, apresenta-se um estudo de caso sobre a Biblioteca Comunitária Professora Ebe Alves da Silva, do Instituto Federal de Minas Gerais que, além de escolar e universitária é também “comunitária”, pela sua própria denominação. Para a concretização do estudo de caso foram realizadas entrevistas e aplicados questionários, dirigidos a diferentes atores da comunidade interna e externa da instituição. Os resultados foram submetidos à técnica do Discurso do Sujeito Coletivo – DSC - que ilustrou a discussão, relacionando os aspectos teóricos sobre biblioteca escolar, biblioteca universitária e biblioteca comunitária à realidade da Biblioteca Comunitária Professora Ebe Alves da Silva. A pesquisa concluiu que a biblioteca estudada cumpre os três papéis, constituindo-se em uma agente propulsora da democratização da informação e contribuindo para o desenvolvimento do município.

As fontes literárias no ensino de História

Directory of Open Access Journals (Sweden)

Joan Pagès Blanch

2013-07-01

Full Text Available Existem muitos recursos para levar aos alunos do ensino fundamental e médio o conhecimento e a compreensão do passado, boa parte deles são habitualmente utilizados nas salas de aula. Provavelmente um dos recursos com mais potencialidades educativas é a literatura e, em especial, o romance. Neste artigo propomos que a literatura pode contribuir para a aprendizagem do passado e qual é o valor educativo das fontes literárias no ensino de história e a sugestão de algumas ideias para o seu tratamento na prática.

Transiente superdifusivo em caminhadas aleatórias com perfil de memória q-exponencial

OpenAIRE

Moura, Thiago Rafael da Silva

2016-01-01

Propomos nesta pesquisa um modelo de caminhada aleatória com perfil de decaimento q-exponencial. A função q-exponencial é uma generalização da função exponencial ordinária. No limite q→1, a função q-exponencial torna-se a função exponencial ordinária. Nosso modelo apresenta um comportamento difusivo Markoviano, onde se sabe que o Teorema Central do Limite proibe superdifusão neste caso. Apesar de neste problema não ser esperado o surgimento de uma transição superdifusiva no limite assintótico...

Memória, história e representações: acreditam os replicantes em suas reminiscências?

Directory of Open Access Journals (Sweden)

Weber Abrahão Jr

2016-06-01

Full Text Available Este artigo resulta de leituras feitas no Mestrado Profissional em História, na UFG, Regional Catalão, para aproveitamento da disciplina Imaginários e Narrativas no Ensino de História. A partir dos conceitos de memória, história e representação, como analisados por diversos autores, o objetivo do artigo é dialogar com livro e filme, icônicos produtos da indústria cultural: Androides Sonham com Ovelhas Elétricas?, é o livro, de Philip Kindred Dick;  Blade Runner, O Caçador de Androides, é sua adaptação cinematográfica. A trama como desenvolvida nas obras, embora distinta em diversos pontos, permite exercício teórico necessário à formação intelectual do professor-pesquisador. Desse modo, o artigo é uma narrativa permeada pela memória afetiva do autor em relação às obras analisadas, constituindo-se em atividade didática a serviço da formação do professor-pesquisador.

Detection of IgE in the sera of rodents: comparison of the applicability of ELISA and RIA

Energy Technology Data Exchange (ETDEWEB)

Reiner, G; Zahner, H [Institut fuer Parasitologie der Justus-Liebig-Universitaet Giessen, Germany, F.R.; Haque, A [Institut Pasteur, 59 - Lille (France). Centre d' Immunologie et de Biologie Parasitaire

1984-04-13

RIA and ELISA were compared for their ability to detect IgE in different rodent species. With a sheep anti-rat IgE antibody good correlation (P < 0.001) between the 2 assay methods for IgE was found in rats. RIA failed to detect the IgE of Mastomys natalensis while ELISA proved to be a suitable test. However, both tests failed to measure IgE in sera of Nile rats.

Modeling RIA scenarios with the FRAPTRAN and SCANAIR codes

International Nuclear Information System (INIS)

Sagrado Garcia, I. C.; Vallejo, I.; Herranz, L. E.

2013-01-01

The need of defining new RIA safety criteria has pointed out the importance of performing a rigorous assessment of the transient codes capabilities. The present work is a comparative exercise devoted to identify the origin of the key deviations found between the predictions of FRAPTRAN-1.4 and SCANAIR-7.1. To do so, the calculations submitted by CIEMAT to the OECD/NEA RIA benchmark have been exploited. This work shows that deviations in clad temperatures mainly come from the treatment of the oxide layer. The systematically higher deformations calculated by FRAPTRAN-1.4 in early failed tests are caused by the different gap closure estimation. Besides, the dissimilarities observed in the FGR predictions are inherent to the different modeling strategies adopted in each code.

Modeling RIA scenarios with the FRAPTRAN and SCANAIR codes

Energy Technology Data Exchange (ETDEWEB)

Sagrado Garcia, I. C.; Vallejo, I.; Herranz, L. E.

2013-07-01

The need of defining new RIA safety criteria has pointed out the importance of performing a rigorous assessment of the transient codes capabilities. The present work is a comparative exercise devoted to identify the origin of the key deviations found between the predictions of FRAPTRAN-1.4 and SCANAIR-7.1. To do so, the calculations submitted by CIEMAT to the OECD/NEA RIA benchmark have been exploited. This work shows that deviations in clad temperatures mainly come from the treatment of the oxide layer. The systematically higher deformations calculated by FRAPTRAN-1.4 in early failed tests are caused by the different gap closure estimation. Besides, the dissimilarities observed in the FGR predictions are inherent to the different modeling strategies adopted in each code.

Uma análise da dinâmica inflacionária brasileira

Directory of Open Access Journals (Sweden)

Francisco Cribari-Neto

2005-12-01

Full Text Available O objetivo central do presente artigo é analisar a dinâmica inflacionária brasileira e medir o grau de inércia em tal dinâmica. De início, nós apresentamos resultados de simulação de Monte Carlo sobre o desempenho em amostras finitas de diferentes variantes da razão de variâncias, uma medida comumente utilizada para a mensuração de persistência de choques no longo prazo. As simulações são realizadas sob inovações normais e não-normais e também com e sem outliers e inliers. Os resultados favorecem uma particular variante robusta da razão de variâncias proposta neste artigo. Os resultados empíricos para o Brasil indicam que o grau de inércia inflacionária neste país é substancialmente maior do que aquele encontrado por Campêlo e Cribari-Neto (Revista Brasileira de Economia, 57, 713-739, 2003; de fato, em alguns períodos da história econômica brasileira recente nós encontramos inércia plena. Todavia, o grau de inércia inflacionária após a implementação do Plano Real é de segunda ordem. Nós analisamos também as dinâmicas inflacionárias da Argentina, Chile e México.The chief goal of this paper is to analyze the Brazilian inflationary dynamics, and to measure the degree of inertia in such dynamics. To that end, we start by reporting Monte Carlo simulation results on the finite-sample performance of different variants of the variance ratio, a well know measure of long-run persistence of shocks. The simulations are performed under normal and nonnormal innovations, and also with and without outliers and inliers. Overall, the results favor a robust variant of the variance ratio we propose. The empirical results for Brazil suggest that the degree of inertia in this country is substantially larger than what was found by Campêlo and Cribari-Neto (Revista Brasileira de Economia 57, 713-739, 2003; indeed, in several periods of the recent economic history we find full inertia. However, the degree of inertia since

Simulation of the LHC injection kicker impedance test bench

CERN Document Server

Tsutsui, H

2003-01-01

The coupling impedance measurements of the LHC injection kicker test bench are simulated by HFSS code. The simulation gives qualitatively good agreement with the measurement. In order to damp the resonances, some ferrite rings are tested in the simulation. Longitudinal resonances are damped by a ferrite ring of large tan$\\delta_{\\mu}$. The effect of the ferrite ring is small for damping the transverse impedance resonance around 30 MHz.

A probabilistic approach for RIA fuel failure criteria

International Nuclear Information System (INIS)

Carlo Vitanza, Dr.

2008-01-01

Substantial experimental data have been produced in support of the definition of the RIA safety limits for water reactor fuels at high burn up. Based on these data, fuel failure enthalpy limits can be derived based on methods having a varying degree of complexity. However, regardless of sophistication, it is unlikely that any deterministic approach would result in perfect predictions of all failure and non failure data obtained in RIA tests. Accordingly, a probabilistic approach is proposed in this paper, where in addition to a best estimate evaluation of the failure enthalpy, a RIA fuel failure probability distribution is defined within an enthalpy band surrounding the best estimate failure enthalpy. The band width and the failure probability distribution within this band are determined on the basis of the whole data set, including failure and non failure data and accounting for the actual scatter of the database. The present probabilistic approach can be used in conjunction with any deterministic model or correlation. For deterministic models or correlations having good prediction capability, the probability distribution will be sharply increasing within a narrow band around the best estimate value. For deterministic predictions of lower quality, instead, the resulting probability distribution will be broad and coarser

Astrophysics at RIA (ARIA) Working Group

International Nuclear Information System (INIS)

Smith, Michael S.; Schatz, Hendrik; Timmes, Frank X.; Wiescher, Michael; Greife, Uwe

2006-01-01

The Astrophysics at RIA (ARIA) Working Group has been established to develop and promote the nuclear astrophysics research anticipated at the Rare Isotope Accelerator (RIA). RIA is a proposed next-generation nuclear science facility in the U.S. that will enable significant progress in studies of core collapse supernovae, thermonuclear supernovae, X-ray bursts, novae, and other astrophysical sites. Many of the topics addressed by the Working Group are relevant for the RIKEN RI Beam Factory, the planned GSI-Fair facility, and other advanced radioactive beam facilities

Extended Leach Testing of Simulated LAW Cast Stone Monoliths

Energy Technology Data Exchange (ETDEWEB)

Serne, R. Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Williams, Benjamin D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jung, H. B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wang, Guohui [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-07-09

This report describes the results from long-term laboratory leach tests performed at Pacific Northwest National Laboratory (PNNL) for Washington River Protection Solutions (WRPS) to evaluate the release of key constituents from monoliths of Cast Stone prepared with four simulated low-activity waste (LAW) liquid waste streams. Specific objectives of the Cast Stone long-term leach tests described in this report focused on four activities: 1. Extending the leaching times for selected ongoing EPA-1315 tests on monoliths made with LAW simulants beyond the conventional 63-day time period up to 609 days reported herein (with some tests continuing that will be documented later) in an effort to evaluate long-term leaching properties of Cast Stone to support future performance assessment activities. 2. Starting new EPA-1315 leach tests on archived Cast Stone monoliths made with four LAW simulants using two leachants (deionized water [DIW] and simulated Hanford Integrated Disposal Facility (IDF) Site vadose zone pore water [VZP]). 3. Evaluating the impacts of varying the iodide loading (starting iodide concentrations) in one LAW simulant (7.8 M Na Hanford Tank Waste Operations Simulator (HTWOS) Average) by manufacturing new Cast Stone monoliths and repeating the EPA-1315 leach tests using DIW and the VZP leachants. 4. Evaluating the impacts of using a non-pertechnetate form of Tc that is present in some Hanford tanks. In this activity one LAW simulant (7.8 M Na HTWOS Average) was spiked with a Tc(I)-tricarbonyl gluconate species and then solidified into Cast Stone monoliths. Cured monoliths were leached using the EPA-1315 leach protocol with DIW and VZP. The leach results for the Tc-Gluconate Cast Stone monoliths were compared to Cast Stone monoliths pertechnetate.

Modelling, simulation and visualisation for electromagnetic non-destructive testing

International Nuclear Information System (INIS)

Ilham Mukriz Zainal Abidin; Abdul Razak Hamzah

2010-01-01

This paper reviews the state-of-the art and the recent development of modelling, simulation and visualization for eddy current Non-Destructive Testing (NDT) technique. Simulation and visualization has aid in the design and development of electromagnetic sensors and imaging techniques and systems for Electromagnetic Non-Destructive Testing (ENDT); feature extraction and inverse problems for Quantitative Non-Destructive Testing (QNDT). After reviewing the state-of-the art of electromagnetic modelling and simulation, case studies of Research and Development in eddy current NDT technique via magnetic field mapping and thermography for eddy current distribution are discussed. (author)

Education and training by utilizing irradiation test reactor simulator

International Nuclear Information System (INIS)

Eguchi, Shohei; Koike, Sumio; Takemoto, Noriyuki; Tanimoto, Masataka; Kusunoki, Tsuyoshi

2016-01-01

The Japan Atomic Energy Agency, at its Japan Materials Testing Reactor (JMTR), completed an irradiation test reactor simulator in May 2012. This simulator simulates the operation, irradiation test, abnormal transient change during operation, and accident progress events, etc., and is able to perform operation training on reactor and irradiation equipment corresponding to the above simulations. This simulator is composed of a reactor control panel, process control panel, irradiation equipment control panel, instructor control panel, large display panel, and compute server. The completed simulator has been utilized in the education and training of JMTR operators for the purpose of the safe and stable operation of JMTR and the achievement of high operation rate after resuming operation. For the education and training, an education and training curriculum has been prepared for use in not only operation procedures at the time of normal operation, but also learning of fast and accurate response in case of accident events. In addition, this simulator is also being used in operation training for the purpose of contributing to the cultivation of human resources for atomic power in and out of Japan. (A.O.)

Memória e história: Hannah Arendt em diálogo com Walter Benjamin

Directory of Open Access Journals (Sweden)

Magalhães, Marionilde Brepohl de

2006-01-01

Full Text Available A autora tem como proposta refletir sobre o papel da memória e da História em nossa cultura contemporânea, através de uma aproximação ao pensamento de Hannah Arendt e Walter Benjamin

A PROJEÇÃO IDENTITÁRIA NO "MURAL DE HISTÓRIAS" DE MAYSA

Directory of Open Access Journals (Sweden)

Guilherme Moreira Fernandes

2011-06-01

Full Text Available Neste artigo, fazemos uma breve reflexão sobre os mecanismos de projeção e formação identitárias presentes no espaço "Mural de Histórias", do portal da minissérie Maysa: quando fala o coração, exibida em 2009 pela TV Globo. A metodologia da análise de conteúdo nos permitiu categorizar as várias facetas da cantora comentadas pelos internautas. Utilizando os estudos de Aluizio Trinta sobre os mecanismos de projeção-identificação, pudemos inferir que parcela dos internautas se dispôs a refletir sobre a identidade deles. Também percebemos que as múltiplas plataformas criadas pela emissora permitem uma aproximação maior do público e um espaço para manifestações de alegrias e angústias.

Enhanced Verification Test Suite for Physics Simulation Codes

Energy Technology Data Exchange (ETDEWEB)

Kamm, J R; Brock, J S; Brandon, S T; Cotrell, D L; Johnson, B; Knupp, P; Rider, W; Trucano, T; Weirs, V G

2008-10-10

This document discusses problems with which to augment, in quantity and in quality, the existing tri-laboratory suite of verification problems used by Los Alamos National Laboratory (LANL), Lawrence Livermore National Laboratory (LLNL), and Sandia National Laboratories (SNL). The purpose of verification analysis is demonstrate whether the numerical results of the discretization algorithms in physics and engineering simulation codes provide correct solutions of the corresponding continuum equations. The key points of this document are: (1) Verification deals with mathematical correctness of the numerical algorithms in a code, while validation deals with physical correctness of a simulation in a regime of interest. This document is about verification. (2) The current seven-problem Tri-Laboratory Verification Test Suite, which has been used for approximately five years at the DOE WP laboratories, is limited. (3) Both the methodology for and technology used in verification analysis have evolved and been improved since the original test suite was proposed. (4) The proposed test problems are in three basic areas: (a) Hydrodynamics; (b) Transport processes; and (c) Dynamic strength-of-materials. (5) For several of the proposed problems we provide a 'strong sense verification benchmark', consisting of (i) a clear mathematical statement of the problem with sufficient information to run a computer simulation, (ii) an explanation of how the code result and benchmark solution are to be evaluated, and (iii) a description of the acceptance criterion for simulation code results. (6) It is proposed that the set of verification test problems with which any particular code be evaluated include some of the problems described in this document. Analysis of the proposed verification test problems constitutes part of a necessary--but not sufficient--step that builds confidence in physics and engineering simulation codes. More complicated test cases, including physics models of

Simulation and interpretation of inter-well tracer tests

Directory of Open Access Journals (Sweden)

Dugstad Øyvind

2013-05-01

Full Text Available In inter-well tracer tests (IWTT, chemical compounds or radioactive isotopes are used to label injection water and gas to establish well connections and fluid patterns in petroleum reservoirs. Tracer simulation is an invaluable tool to ease the interpretation of IWTT results and is also required for assisted history matching application of tracer data. In this paper we present a new simulation technique to analyse and interpret tracer results. Laboratory results are used to establish and test formulations of the tracer conservation equations, and the technique is used to provide simulated tracer responses that are compared with observed tracer data from an extensive tracer program. The implemented tracer simulation methodology use a fast post-processing of previously simulated reservoir simulation runs. This provides a fast, flexible and powerful method for analysing gas tracer behaviour in reservoirs. We show that simulation time for tracers can be reduced by factor 100 compared to solving the tracer flow equations simultaneously with the reservoir fluid flow equations. The post-processing technique, combined with a flexible built-in local tracer-grid refinement is exploited to reduce numerical smearing, particularly severe for narrow tracer pulses.

DINÂMICA DA MEMÓRIA: LEITE DERRAMADO E MEMÓRIAS PÓSTUMAS DE BRÁS CUBAS

Directory of Open Access Journals (Sweden)

JURACY ASSMANN SARAIVA

Full Text Available Resumo Partindo do pressuposto de que a memória é um dos fundamentos da literatura, o artigo compara Leite derramado, de Chico Buarque, com Memórias póstumas de Brás Cubas, de Machado de Assis. A análise explicita semelhanças e diferenças entre esses romances memorialísticos, relativas a aspectos temáticos e composicionais, e comprova que ambos compõem uma alegoria da nacionalidade brasileira, estabelecendo um paralelismo entre o percurso da vida dos protagonistas, ou de sua família, e episódios da história do Brasil. Conclui que os procedimentos criativos das narrativas compõem um jogo de espelhos que, ao envolver o leitor, reivindica a importância da literatura como espaço de reflexão sobre si mesma e sobre acontecimentos da história, os quais a ficção projeta sob nova luz.

A Reportagem Jornalistica e a Memória - Histórias em Movimento

Directory of Open Access Journals (Sweden)

Jerusa de Oliveira Michel

2016-03-01

Full Text Available O trabalho analisa a partir de diferentes campos do conhecimento: antropologia, etnografia, etnicidade, território, história e memória em suas diversas abordagens, e o gênero jornalístico reportagem, a perspectiva de construção de conhecimento interdisciplinar, identificando os pontos de convergência entre os campos. Utiliza metodologia etnográfica/interdisciplinar, focando o trabalho da jornalista Eliane Brum à luz do referencial teórico construído.

HISTÓRIAS E MEMÓRIAS INSTITUCIONAIS A PARTIR DO ACERVO FOTOGRÁFICO DO CENTRO UNIVERSITÁRIO FRANCISCANO (1955 1980)

OpenAIRE

Luciana Souza de Brito

2010-01-01

Este trabalho apresenta o estudo acerca das histórias e memórias do Centro Universitário Franciscano, que podem ser interpretadas por meio da análise do acervo fotográfico da instituição. O objetivo geral desse trabalho consiste no tratamento, de acordo com os critérios arquivísticos, do acervo fotográfico do Centro Universitário Franciscano, referente ao período situado entre os anos de 1955 e 1980, com a finalidade de estudar e evocar as histórias e memórias da instituição. Como objetivo...

Coriorretinite esclopetária

Directory of Open Access Journals (Sweden)

Isaac Carvalho de Oliveira Ramos

2015-06-01

Full Text Available O objetivo deste trabalho é relatar um caso de trauma ocular por projétil de arma de fogo, que atingiu e se alojou na cavidade orbitária, desenvolvendo coriorretinite esclopetária. Foram abordados o mecanismo fisiopatológico, os principais achados clínicos e de exames complementares, além das opções de tratamento. As características do caso relatado reforçam a importância de uma abordagem multidisciplinar no trauma ocular.

RIA determination of aflatoxin B1 in food

International Nuclear Information System (INIS)

Bludovsky, R.

1986-01-01

The possibility was tested of the application of a commercial RIA kit in determining aflatoxin B 1 in foodstuffs. Stability, sensitivity, specificity and the effect of interfering materials were studied. Alternative methods were tested of sample preparation and a technique was proposed usable for food analysis. The kit was found to be mainly suitable for screening and for the determination of aflatoxin B 1 in concentrations exceedings 1 μg/kg. Lipids were found to cause a systematic positive error and should thus be removed by extraction prior to analysis. (author). 10 tabs., 15 refs

Application of the SCANAIR code for VVER RIA conditions - Boron dilution accident

International Nuclear Information System (INIS)

Arffman, A.; Cazalis, B.

2010-01-01

This paper consists of two parts. In part A, RIA pulse tests conducted at the Russian BIGR reactor are being analysed at IRSN with SCANAIR V6 fuel performance code as a part of the code validation for VVER fuel. Recently a new version of the SCANAIR code was made available to VTT Technical Research Centre of Finland, and part B of the paper covers the introduction of the code version at VTT by a calculation of a hypothetical boron dilution accident in a VVER-440 power reactor. Concerning part A, it appears that the SCANAIR V6 version, including a BIGR/NSRR heat transfer model, validated by Japanese NSRR experiments, and a Norton viscoplastic clad mechanical behaviour, is able to simulate the rod thermal behaviour in BIGR tests. Concerning the clad mechanics, it has been seen that a pellet swelling model is able to simulate the average rod deformation. Nonetheless, the current clad creep model associated with the free volume equilibrium assumption is not suited to predict the maximum clad deformation and the possible post DNB rod failure because they do not simulate local balloons. Furthermore, it has been shown that the clad deformation is strongly dependent on transient gas transfer. Concerning part B, a boron dilution accident previously calculated with SCANAIR V2 was recalculated with SCANAIR V6. A limited amount of result parameters were compared with the results of VTT's neutronics code TRAB. Divergence problems encountered previously when reaching the DNB limit were not present anymore. Fuel and cladding temperatures produced by SCANAIR were in good agreement with those calculated with TRAB

Meta-memória e auto-eficácia: um estudo de validação de instrumentos de pesquisa sobre memória e envelhecimento Metamemory and self-efficacy: a validation study of research instruments in memory aging

Directory of Open Access Journals (Sweden)

Mônica Sanches Yassuda

2005-04-01

Full Text Available A literatura cognitiva documenta em inúmeros relatos a existência de diferenças significativas entre o desempenho de jovens e idosos em tarefas de memória episódica. Pesquisadores nas últimas décadas exploram possíveis explicações para esta discrepância. Uma das hipóteses em investigação é que talvez os idosos possuam percepções, atitudes e afetos diferentes relativos à memória, e que talvez seu desempenho seja afetado por estes fatores. Os conceitos de meta-memória e auto-eficácia têm sido empregados nas pesquisas sobre o envelhecimento da memória para a avaliação desta hipótese. Nesta pesquisa, 1 questionário de meta-memória (MIA, 1 questionário de auto-eficácia (MSEQ e 4 versões de 2 tarefas de desempenho de memória episódica (4 listas de itens de supermercado e 4 histórias curtas foram traduzidos para o português, adaptados à cultura brasileira e submetidos a testes de validação junto a 33 jovens e 27 idosos saudáveis brasileiros. Os resultados das análises realizadas sugerem que as versões em português destes instrumentos têm boas características psicométricas e são promissores para esta área de pesquisa no Brasil.The cognitive aging literature documents in numerous studies the existence of significant age differences between younger and older adults in tests of episodic memory. Researchers have been investigating possible explanations for such differences. One hypothesis being tested is whether older adults hold different perceptions, attitudes and feelings towards memory that could affect performance negatively. Metamemory and self-efficacy are concepts that have been used in the test of this hypothesis. In the present research, a metamemory questionnaire (MIA, a self-efficacy questionnaire (MSEQ and 4 versions of 2 episodic memory tasks (4 grocery lists and 4 short stories were translated into Portuguese, adapted to Brazilian culture and submitted to validity testing with 33 younger and 27

O PESO DA MEMÓRIA: LITERATURA E HISTÓRIA NA ACÁDIA.

OpenAIRE

Finney, James de

2012-01-01

A história está no centro da literatura e da identidade dos acadianos, uma história extremamente rica, de consonâncias míticas e bíblicas: um povo inocente é forçado a dispersar-se pelo continente americano e pela Europa, de 1755 a 1762, condenado ao exílio e à errância, antes de poder reconquistar penosamente seu direito à existência. Entretanto, a força emotiva e a coerência dessa narrativa constituem, para os acadianos, uma faca de dois gumes: numerosos autores, ao difundi-la, confinaram a...

Safety panel and new procedures evaluation by simulator tests

International Nuclear Information System (INIS)

Meslin, T.

1986-01-01

With more than thirty weeks of simulator testing (for the last three years only) and approximately three hundred scenarios, EDF's experience in this field is extensive. This practice is well known within Fossil and Nuclear Generation and is well accepted by the operating teams which participate in it. Simulator testing appears to be an essential decision-making tool in the process of developing new operating aids in PWR plants. Accelerated development and the elimination of long and expensive modifications after commissioning is an economic advantage. The saving in time is obvious, since modifications are carried out continuously throughout the development phase. Finally, operators participate in the development of systems and receive fixed, well-defined applications. This practice has become systematic, and all new applications concerning the operation of PWR plants are simulator-tested, particularly 1300-MW unit computers and operating procedures, the new generation of 900-MW unit computers, and the new 1500-MW fully computerized control rooms. Finally, this simulator testing allows us to considerably increase our knowledge concerning the behavior of operators in accident situations, and special tests are performed for this purpose

Comparative study of the enzyme linked immunosorbent assay (ELISA) and two radioimmunoassays (RIA'S) for in-sulin

Energy Technology Data Exchange (ETDEWEB)

Klimes, I; Jurcovicova, J; Palkovic, M [Slovenska Akademia Vied, Bratislava (Czechoslovakia). Ustav Experimentalnej Endokrinologie

1978-06-30

The results of the quality control tests for enzyme linked immunosorbent assay (ELISA) were compared with the results of two different radioimmunoassays (RIA'S) for insulin. Using the manufacturer's procedure for the ELISA kit we found that the analytical variables such as assay sensitivity, recovery study and the 50% binding intercept were in good agreement with those obtained with the RIA method.

Testing philosophy and simulation techniques

International Nuclear Information System (INIS)

Holtbecker, H.

1977-01-01

This paper reviews past and present testing philosophies and simulation techniques in the field of structure loading and response studies. The main objective of experimental programmes in the past was to simulate a hypothetical energy release with explosives and to deduce the potential damage to a reactor from the measured damage to the model. This approach was continuously refined by improving the instrumentation of the models, by reproducing the structures as faithful as possible and by developing new explosive charges. This paper presents an analysis of the factors which are expected to have an influence on the validity of the results e.g. strain rate effects and the use of water instead of sodium. More recently the discussion of a whole series of accidents in the probabilistic accident analysis and the intention to compare different reactor designs has revealed the need to develop and validate computer codes. Consequently experimental programmes have been started in which the primary aim is not to test a specific reactor but to validate codes. This paper shows the principal aspects of this approach and discusses first results. (Auth.)

Reliability Verification of DBE Environment Simulation Test Facility by using Statistics Method

International Nuclear Information System (INIS)

Jang, Kyung Nam; Kim, Jong Soeg; Jeong, Sun Chul; Kyung Heum

2011-01-01

In the nuclear power plant, all the safety-related equipment including cables under the harsh environment should perform the equipment qualification (EQ) according to the IEEE std 323. There are three types of qualification methods including type testing, operating experience and analysis. In order to environmentally qualify the safety-related equipment using type testing method, not analysis or operation experience method, the representative sample of equipment, including interfaces, should be subjected to a series of tests. Among these tests, Design Basis Events (DBE) environment simulating test is the most important test. DBE simulation test is performed in DBE simulation test chamber according to the postulated DBE conditions including specified high-energy line break (HELB), loss of coolant accident (LOCA), main steam line break (MSLB) and etc, after thermal and radiation aging. Because most DBE conditions have 100% humidity condition, in order to trace temperature and pressure of DBE condition, high temperature steam should be used. During DBE simulation test, if high temperature steam under high pressure inject to the DBE test chamber, the temperature and pressure in test chamber rapidly increase over the target temperature. Therefore, the temperature and pressure in test chamber continue fluctuating during the DBE simulation test to meet target temperature and pressure. We should ensure fairness and accuracy of test result by confirming the performance of DBE environment simulation test facility. In this paper, in order to verify reliability of DBE environment simulation test facility, statistics method is used

Quando Clio toca as Pandoras: os arquivos entre histórias e memórias DOI: 10.5965/2175180305092013203

Directory of Open Access Journals (Sweden)

Sylvie Sagnes

2013-06-01

Full Text Available História e memória não são duas noções que podem sobrepor-se exatamente e isto tanto menos quanto o passado do qual elas dão conta traz a marca de um traumatismo da história. No coração das relações desarmônicas que têm Clio e Mnemósine, guarda-se o arquivo. Em semelhante caso, o tratamento do qual este é objeto constitui de modo incontestável um observatório das inumeráveis implicações que a rememoração do passado suscita. Se alguns duvidam dessa verdade, os trabalhos e ensaios franceses dos quais este artigo propõe a síntese o ilustram eloquentemente. Eles mostram, em contraposição às ambições que o arquivo suscita, o poder que nossas representações ocidentais imputam à sua posse. Alvo de uma violência de outro gênero, o arquivo negligenciado nutre polêmicas a favor das quais variam as alianças e se movem linhas de ruptura. Sobre o tabuleiro da memória, militantes, historiadores profissionais, políticos, legisladores e juízes jogam um jogo complicado, do qual, a contar dos anos 1980, participam as testemunhas assim como os historiadores provindos das fileiras das comunidades memoriais. À prova da prova, as memórias se entrechocam. Memórias dominadas e dominantes, vitimárias e heroicas, subjetivas e objetivas, memórias do coração e da razão se opõem em um estrépito cujos solavancos afetam infalivelmente a disciplina histórica.

Hot ductility testing and weld simulation tests

International Nuclear Information System (INIS)

Weber, G.; Schick, M.

1999-01-01

The objective of the project was to enhance the insight into the causes of intergranular cracks detected in austenitic circumferential welds at BWR pipes. The susceptibility of a variety of austenitic pipe materials to hot cracking during welding and in-service intergranular crack corrosion was examined. The assumption was cracking in the root area of the HAZ of a multiple-layer weld. Hot-ductility tests and weld simulation tests specifically designed for the project were performed with the austenitic LWR pipe materials 1.4553 (X6 CrNiNb 18 10 S), 1.4550 (X10 CrNiNb 18 9), 1.4533 (X6 CrNiTi 18 9, two weld pools), and a non-stabilized TP 304 (X5 CrNi 18 10). (orig./CB) [de

NUMERICAL SIMULATION OF AN AGRICULTURAL SOIL SHEAR STRESS TEST

Directory of Open Access Journals (Sweden)

Andrea Formato

2007-03-01

Full Text Available In this work a numerical simulation of agricultural soil shear stress tests was performed through soil shear strength data detected by a soil shearometer. We used a soil shearometer available on the market to measure soil shear stress and constructed special equipment that enabled automated detection of soil shear stress. It was connected to an acquisition data system that displayed and recorded soil shear stress during the full field tests. A soil shearometer unit was used to the in situ measurements of soil shear stress in full field conditions for different types of soils located on the right side of the Sele river, at a distance of about 1 km from each other, along the perpendicular to the Sele river in the direction of the sea. Full field tests using the shearometer unit were performed alongside considered soil characteristic parameter data collection. These parameter values derived from hydrostatic compression and triaxial tests performed on considered soil samples and repeated 4 times and we noticed that the difference between the maximum and minimum values detected for every set of performed tests never exceeded 4%. Full field shear tests were simulated by the Abaqus program code considering three different material models of soils normally used in the literature, the Mohr-Coulomb, Drucker-Prager and Cam-Clay models. We then compared all data outcomes obtained by numerical simulations with those from the experimental tests. We also discussed any further simulation data results obtained with different material models and selected the best material model for each considered soil to be used in tyre/soil contact simulation or in soil compaction studies.

26th Space Simulation Conference Proceedings. Environmental Testing: The Path Forward

Science.gov (United States)

Packard, Edward A.

2010-01-01

Topics covered include: A Multifunctional Space Environment Simulation Facility for Accelerated Spacecraft Materials Testing; Exposure of Spacecraft Surface Coatings in a Simulated GEO Radiation Environment; Gravity-Offloading System for Large-Displacement Ground Testing of Spacecraft Mechanisms; Microscopic Shutters Controlled by cRIO in Sounding Rocket; Application of a Physics-Based Stabilization Criterion to Flight System Thermal Testing; Upgrade of a Thermal Vacuum Chamber for 20 Kelvin Operations; A New Approach to Improve the Uniformity of Solar Simulator; A Perfect Space Simulation Storm; A Planetary Environmental Simulator/Test Facility; Collimation Mirror Segment Refurbishment inside ESA s Large Space; Space Simulation of the CBERS 3 and 4 Satellite Thermal Model in the New Brazilian 6x8m Thermal Vacuum Chamber; The Certification of Environmental Chambers for Testing Flight Hardware; Space Systems Environmental Test Facility Database (SSETFD), Website Development Status; Wallops Flight Facility: Current and Future Test Capabilities for Suborbital and Orbital Projects; Force Limited Vibration Testing of JWST NIRSpec Instrument Using Strain Gages; Investigation of Acoustic Field Uniformity in Direct Field Acoustic Testing; Recent Developments in Direct Field Acoustic Testing; Assembly, Integration and Test Centre in Malaysia: Integration between Building Construction Works and Equipment Installation; Complex Ground Support Equipment for Satellite Thermal Vacuum Test; Effect of Charging Electron Exposure on 1064nm Transmission through Bare Sapphire Optics and SiO2 over HfO2 AR-Coated Sapphire Optics; Environmental Testing Activities and Capabilities for Turkish Space Industry; Integrated Circuit Reliability Simulation in Space Environments; Micrometeoroid Impacts and Optical Scatter in Space Environment; Overcoming Unintended Consequences of Ambient Pressure Thermal Cycling Environmental Tests; Performance and Functionality Improvements to Next Generation

Behavior of pre-irradiated fuel under a simulated RIA condition. Results of NSRR Test JM-5

International Nuclear Information System (INIS)

Fuketa, Toyoshi; Sasajima, Hideo; Mori, Yukihide; Tanzawa, Sadamitsu; Ishijima, Kiyomi; Kobayashi, Shinsho; Kamata, Hiroshi; Homma, Kozo; Sakai, Haruyuki.

1995-11-01

This report presents results from the power burst experiment with pre-irradiated fuel rod, Test JM-5, conducted in the Nuclear Safety Research Reactor (NSRR). The data concerning test method, pre-irradiation, pre-pulse fuel examination, pulse irradiation, transient records and post-pulse fuel examination are described, and interpretations and discussions of the results are presented. Preceding to the pulse irradiation in the NSRR, test fuel rod was irradiated in the Japan Materials Testing Reactor (JMTR) up to a fuel burnup of 25.7 MWd/kgU with average linear heat rate of 33.4 kW/m. The fuel rod was subjected to the pulse irradiation resulting in a desposited energy of 223 ± 7 cal/g·fuel (0.93 ± 0.03 kJ/g·fuel) and a peak fuel enthalpy of 167 ± 5 cal/g·fuel (0.70 ± 0.02 kJ/g·fuel) under stagnant water cooling condition at atmospheric pressure and ambient temperature. Test fuel rod behavior was assessed from pre- and post-pulse fuel examinations and transient records during the pulse. The Test JM-5 resulted in cladding failure. More than twenty small cracks were found in the post-test cladding, and most of the defects located in pre-existing locally hydrided region. The result indicates an occurrence of fuel failure by PCMI (pellet/cladding mechanical interaction) in combination with decreased integrity of hydrided cladding. (author)

Dynamic stack testing and HiL simulation

Energy Technology Data Exchange (ETDEWEB)

Randolf, G. [GRandalytics, Honolulu, HI (United States)

2009-07-01

The applications for fuel cell and stack deployment have changed rapidly over the years, from stationary backup supplies to highly dynamic automotive power systems. As a result, testing must keep up in order to ensure mature products of high quality. A new breed of stack test stations has been designed, based on a newly developed single cell, high dynamic hardware-in-the-loop (HiL) simulator in order to meet the growing demand of realistic fuel cell testing scenarios for aviation and automotive industries. The paper described and illustrated the test station architecture and outline of communication nodes. The paper also described the voltage monitor and presented schematics of voltage monitoring modules. The basic requirements of the architecture that were presented included low latency; flexible communication with simulation targets and other data input/output nodes; scalability to various stack sizes; and, safety and reliability. It was concluded that first tests with the voltage monitoring system not only confirmed the design, high throughput and signal quality, but also suggested another application, namely a stack impedance spectrometer for each individual cell. 1 ref., 3 figs.

Simulation tests of plastic-packaged commercial SRAM

International Nuclear Information System (INIS)

Kalashnikov, O.A.; Nikiforov, A.Y.

1999-01-01

Laser and X-ray simulation test technique is developed adopted to plastic-packaged ICs. Dose rate and total dose test results are presented for two types of commercial RAMS. Dose rate and total dose test results were obtained for two types of commercial RAMS: AS7C256-20 256 K (32 K x 8) and MT5C1008W - 1 M (128 K x 8). The latch-up of AS7C256-20 was detected at dose rate 1.510 9 rad(Si)/s and of MT5C1008W - at dose rate 5.7-10 8 rad(Si)/s. The total dose failure thresholds were in the ranges of 55 to 90 krad(Si) for AS7C25620 and 40 to 328 krad for MT5C1008W depending on RAM operational mode under irradiation. The obtained simulation test results are in a good agreement with previously published for radiation installations. (authors)

(A)bordar memórias, tecer histórias : fazeres teatrais em Brasília (1970-1990)

OpenAIRE

Carrijo, Elizângela

2010-01-01

(A)bordar e tecer lembram habilidades manuais e produções que, no final, têm o toque de quem as cria. Aqui, não é diferente, pois, ao tecer histórias ao longo dessas páginas, dei pontos e enlaces por meio de memórias relatadas por Dulcina de Moraes, Geraldo Martuchelli, Hugo Rodas, Humberto Pedrancini, Iara Pietricovsky, Jesus Vivas, João Antônio e José Maria B. de Paiva, construindo assim uma narrativa compartilhada, com nossos toques especiais. Ao estudar história e cultura, fazendo uso da ...

2-d Simulations of Test Methods

DEFF Research Database (Denmark)

Thrane, Lars Nyholm

2004-01-01

One of the main obstacles for the further development of self-compacting concrete is to relate the fresh concrete properties to the form filling ability. Therefore, simulation of the form filling ability will provide a powerful tool in obtaining this goal. In this paper, a continuum mechanical...... approach is presented by showing initial results from 2-d simulations of the empirical test methods slump flow and L-box. This method assumes a homogeneous material, which is expected to correspond to particle suspensions e.g. concrete, when it remains stable. The simulations have been carried out when...... using both a Newton and Bingham model for characterisation of the rheological properties of the concrete. From the results, it is expected that both the slump flow and L-box can be simulated quite accurately when the model is extended to 3-d and the concrete is characterised according to the Bingham...

WIPP waste package testing on simulated DHLW: emplacement

International Nuclear Information System (INIS)

Molecke, M.A.

1984-01-01

Several series of simulated (nonradioactive) defense high-level waste (DHLW) package tests have been emplaced in the WIPP, a research and development facility authorized to demonstrate the safe disposal of defense-related wastes. The primary purpose of these 3-to-7 year duration tests is to evaluate the in situ materials performance of waste package barriers (canisters, overpacks, backfills, and nonradioactive DHLW glass waste form) for possible future application to a licensed waste repository in salt. This paper describes all test materials, instrumentation, and emplacement and testing techniques, and discusses progress of the various tests. These tests are intended to provide information on materials behavior (i.e., corrosion, metallurgical and geochemical alterations, waste form durability, surface interactions, etc.), as well as comparison between several waste package designs, fabrications details, and actual costs. These experiments involve 18 full-size simulated DHLW packages (approximately 3.0 m x 0.6 m diameter) emplaced in vertical boreholes in the salt drift floor. Six of the test packages contain internal electrical heaters (470 W/canister), and were emplace under approximately reference DHLW repository conditions. Twelve other simulated DHLW packages were emplaced under accelerated-aging or overtest conditions, including the artificial introduction of brine, and a thermal loading approximately three to four times higher than reference. Eight of these 12 test packages contain 1500 W/canister electrical heaters; the other four are filled with DHLW glass. 9 refs., 1 fig

Claire, a simulation and testing tool for critical softwares

International Nuclear Information System (INIS)

Gassino, J.; Henry, J.Y.

1996-01-01

The CEA and IPSN (Institute of Nuclear Protection and Safety) needs concerning the testing of critical softwares, have led to the development of the CLAIRE tool which is able to test the softwares without modification. This tool allows to graphically model the system and its environment and to include components into the model which observe and do not modify the behaviour of the system to be tested. The executable codes are integrated in the model. The tool uses target machine simulators (microprocessors). The technique used (the event simulation) allows to associate actions with events such as the execution of an instruction, the access to a variable etc.. The simulation results are exploited using graphic, states research and test cover measurement tools. In particular, this tool can give help to the evaluation of critical softwares with pre-existing components. (J.S.)

TREAT [Transient Reactor Test Facility] reactor control rod scram system simulations and testing

International Nuclear Information System (INIS)

Solbrig, C.W.; Stevens, W.W.

1990-01-01

Air cylinders moving heavy components (100 to 300 lbs) at high speeds (above 300 in/sec) present a formidable end-cushion-shock problem. With no speed control, the moving components can reach over 600 in/sec if the air cylinder has a 5 ft stroke. This paper presents an overview of a successful upgrade modification to an existing reactor control rod drive design using a computer model to simulate the modified system performance for system design analysis. This design uses a high speed air cylinder to rapidly insert control rods (278 lb moved 5 ft in less than 300 msec) to scram an air-cooled test reactor. Included is information about the computer models developed to simulate high-speed air cylinder operation and a unique new speed control and end cushion design. A patent application is pending with the US Patent ampersand Trade Mark Office for this system (DOE case number S-68,622). The evolution of the design, from computer simulations thru operational testing in a test stand (simulating in-reactor operating conditions) to installation and use in the reactor, is also described. 6 figs

Anastomose mamária-coronária: análise de 2923 casos Mammary-coronary artery anastomosis: analysis of 2923 cases

Directory of Open Access Journals (Sweden)

Jarbas J Dinkhuysen

1987-04-01

Full Text Available Foi a partir de 1972 que, no Instituto Dante Pazzanese de Cardiologia, se iniciou o emprego da anastomose mamária-coronária associada, ou não, a pontes de safena, ou a outros procedimentos. Nessa época, apenas a artéria mamária interna esquerda (AMIE foi usada (57 casos para a revascularização da descendente anterior (DA ou diagonal. No período 1973/1974 (386 casos, já ocorreram as primeiras anastomoses seqüenciais AMIE-DA/DA, assim como a artéria mamária interna direita (AMID passou a ser empregada para ramos diagonais. Com a finalidade de verificar a evolução tardia desta técnica, sua aplicação foi praticamente interrompida, entre 1975/1982, restringindo-se a apenas 43 casos, nesse período. Entretanto, a partir de 1982 até junho de 1986, ocorreu significativo incremento na sua aplicação (2374 casos, sendo que, desde então, a quase totalidade (93% das cirurgias de revascularização do miocárdio tem uma ou mais coronárias tratadas com anastomose mamária-coronária. A combinação mais freqüente é AMIE/DA nos casos de mamária isolada e AMIE/DA e AMID/Mg Cx nos casos de dupla mamária. Contudo, observaram-se, na casuística, as mais variadas combinações (71 e associações, abrangendo, praticamente, todas as artérias coronárias. Analisando-se o pós-operatório imediato de um grupo isolado de 177 pacientes operados em 1984, observou-se que esta técnica não influiu na ocorrência de deiscência parcial, ou total, de esterno, em reoperação por sangramento; todavia, ocorreram, em 25% dos casos, elevação transitória da cúpula frénica, atelectasia em 17% e derrame pleural residual em 27,6%, geralmente concomitantes. Em relação à evolução tardia, num grupo de 754 pacientes com mamária e safena e com evolução até 9 anos, em 924 (71,8% dos enxertos reestudados, constataram-se índices de permeabilidade de 91,5% nas mamárias versus 70,6% (826 das pontes de safena. Em outro grupo (102 pacientes, com evolu

Determination of serum digosin. A comparison between RIA and EIA

International Nuclear Information System (INIS)

Spitz, J.; Braun, J.S.; Schmidt, M.; Krankenhausstiftung Bamberg

1979-01-01

The results of two radioimmunoassays (RIA, precipitating technique), of a homogenous (EMIT) and a heterogenous (ELISA) enzyme immunoassay (EIA) for ascertaining the amounts of digoxin showed a good correlation in precision and a reasonably AK satisfying correlation in the recovery. However, there was a clear discrepancy in the amounts of digoxin concentrate in the serum of patients. Only the RIA of Abbott and the EIA of Boehringer showed no significant differences. Particularly noticeable was the tendency towards lower values in the EMIT-technique as well as its liability to unspecific serum changes (lipaemia etc.), which often made the detection of digoxin impossible. The routine use of this technique appears problematic. The need for establishing one's own laboratory and test-specific therapeutical range is pointed out. (orig.) [de

Determination of serum digosin. A comparison between RIA and EIA

Energy Technology Data Exchange (ETDEWEB)

Spitz, J; Braun, J S; Schmidt, M [Krankenhausstiftung Bamberg (Germany, F.R.). Nuklearmedizinische Abt.; Abt fuer Labormedizin, Krankenhausstiftung Bamberg [Germany, F.R.

1979-12-01

The results of two radioimmunoassays (RIA, precipitating technique), of a homogenous (EMIT) and a heterogenous (ELISA) enzyme immunoassay (EIA) for ascertaining the amounts of digoxin showed a good correlation in precision and a reasonably AK satisfying correlation in the recovery. However, there was a clear discrepancy in the amounts of digoxin concentrate in the serum of patients. Only the RIA of Abbott and the EIA of Boehringer showed no significant differences. Particularly noticeable was the tendency towards lower values in the EMIT-technique as well as its liability to unspecific serum changes (lipaemia etc.), which often made the detection of digoxin impossible. The routine use of this technique appears problematic. The need for establishing one's own laboratory and test-specific therapeutical range is pointed out.

Design of a Realistic Test Simulator For a Built-In Self Test Environment

Directory of Open Access Journals (Sweden)

A. Ahmad

2010-12-01

Full Text Available This paper presents a realistic test approach suitable to Design For Testability (DFT and Built- In Self Test (BIST environments. The approach is culminated in the form of a test simulator which is capable of providing a required goal of test for the System Under Test (SUT. The simulator uses the approach of fault diagnostics with fault grading procedure to provide the tests. The tool is developed on a common PC platform and hence no special software is required. Thereby, it is a low cost tool and hence economical. The tool is very much suitable for determining realistic test sequences for a targeted goal of testing for any SUT. The developed tool incorporates a flexible Graphical User Interface (GUI procedure and can be operated without any special programming skill. The tool is debugged and tested with the results of many bench mark circuits. Further, this developed tool can be utilized for educational purposes for many courses such as fault-tolerant computing, fault diagnosis, digital electronics, and safe - reliable - testable digital logic designs.

Representação do Passado e História Pública: a História das Mulheres na Internet

Directory of Open Access Journals (Sweden)

Gabriela Correa

2016-12-01

Full Text Available Este artigo tem por objetivo abordar as relações entre internet, representação do passado e história pública. Para tanto, se valerá da análise do website e página do Facebook “As Mina na História”, criada em junho de 2015. Neste exame, explorará questões tais como o tipo de representação do passado oferecido neste espaço virtual, o perfil da sua audiência e a linguagem utilizada. A fim de avançar em tais problemáticas, são tecidos alguns breves comentários sobre o ensino de história das mulheres no Brasil. Por fim, busca-se, a partir desta abordagem, propor algumas reflexões sobre a história pública que tem sido praticada no país, para além da questão da ampliação do público “consumidor” de história.   Palavras-chave: Representação; História Pública; Internet; Mulheres.

Acuidade olfatória e qualidade de vida após a laringectomia total

Directory of Open Access Journals (Sweden)

Christiane Gouvêa dos Santos

2015-12-01

Full Text Available RESUMO: Objetivo: identificar a prevalência e os fatores associados às alterações do olfato e descrever a qualidade de vida após a laringectomia total. Métodos: estudo transversal para avaliar a acuidade olfatória e a qualidade de vida de laringectomizados totais no Instituto Nacional de Câncer por meio da aplicação do Teste de Identificação do Olfato da Universidade da Pensilvânia, do Questionário de Qualidade de Vida da Universidade de Washington e do Questionário sobre a Acuidade Olfatória Pré-Reabilitação do Olfato. Resultados: foram avaliados 48 laringectomizados totais, sendo 39 do sexo masculino e 9 do sexo feminino, com idade média de 62 anos e tempo médio de 5,6 anos desde a laringectomia total. No Teste de Identificação do Olfato a pontuação média foi de 17,9. De acordo com a classificação do olfato no teste, a maioria dos participantes apresentou algum grau de alteração, sendo que apenas 2 indivíduos tiveram o olfato considerado dentro da normalidade. No Questionário de Qualidade de vida da Universidade de Washington, o escore composto foi 80,47. Os domínios que apresentaram as médias de pontos mais baixas foram paladar, saliva e fala. No questionário sobre a acuidade olfatória pré-reabilitação do olfato, a maioria dos participantes consideraram seu olfato de ruim a razoável. 21 indivíduos relataram apresentar algum grau de dificuldade em suas atividades de vida diária em decorrência de alterações do olfato. Conclusão: os laringectomizados totais apresentaram alta prevalência de alterações do olfato, com comprometimentos relacionados às suas atividades de vida diária.

Measurement Invariance and Latent Mean Differences in the Reynolds Intellectual Assessment Scales (RIAS): Does the German Version of the RIAS Allow a Valid Assessment of Individuals with a Migration Background?

Science.gov (United States)

Gygi, Jasmin T.; Fux, Elodie; Grob, Alexander; Hagmann-von Arx, Priska

2016-01-01

This study examined measurement invariance and latent mean differences in the German version of the Reynolds Intellectual Assessment Scales (RIAS) for 316 individuals with a migration background (defined as speaking German as a second language) and 316 sex- and age-matched natives. The RIAS measures general intelligence (single-factor structure) and its two components, verbal and nonverbal intelligence (two-factor structure). Results of a multi-group confirmatory factor analysis showed scalar invariance for the two-factor and partial scalar invariance for the single-factor structure. We conclude that the two-factor structure of the RIAS is comparable across groups. Hence, verbal and nonverbal intelligence but not general intelligence should be considered when comparing RIAS test results of individuals with and without a migration background. Further, latent mean differences especially on the verbal, but also on the nonverbal intelligence index indicate language barriers for individuals with a migration background, as subtests corresponding to verbal intelligence require higher skills in German language. Moreover, cultural, environmental, and social factors that have to be taken into account when assessing individuals with a migration background are discussed. PMID:27846270

Measurement Invariance and Latent Mean Differences in the Reynolds Intellectual Assessment Scales (RIAS: Does the German Version of the RIAS Allow a Valid Assessment of Individuals with a Migration Background?

Directory of Open Access Journals (Sweden)

Jasmin T Gygi

Full Text Available This study examined measurement invariance and latent mean differences in the German version of the Reynolds Intellectual Assessment Scales (RIAS for 316 individuals with a migration background (defined as speaking German as a second language and 316 sex- and age-matched natives. The RIAS measures general intelligence (single-factor structure and its two components, verbal and nonverbal intelligence (two-factor structure. Results of a multi-group confirmatory factor analysis showed scalar invariance for the two-factor and partial scalar invariance for the single-factor structure. We conclude that the two-factor structure of the RIAS is comparable across groups. Hence, verbal and nonverbal intelligence but not general intelligence should be considered when comparing RIAS test results of individuals with and without a migration background. Further, latent mean differences especially on the verbal, but also on the nonverbal intelligence index indicate language barriers for individuals with a migration background, as subtests corresponding to verbal intelligence require higher skills in German language. Moreover, cultural, environmental, and social factors that have to be taken into account when assessing individuals with a migration background are discussed.

Platform for Testing Robotic Vehicles on Simulated Terrain

Science.gov (United States)

Lindemann, Randel

2006-01-01

The variable terrain tilt platform (VTTP) is a means of providing simulated terrain for mobility testing of engineering models of the Mars Exploration Rovers. The VTTP could also be used for testing the ability of other robotic land vehicles (and small vehicles in general) to move across terrain under diverse conditions of slope and surface texture, and in the presence of obstacles of various sizes and shapes. The VTTP consists mostly of a 16-ft-(4.88-m)-square tilt table. The tilt can be adjusted to any angle between 0 (horizontal) and 25 . The test surface of the table can be left bare; can be covered with hard, high-friction material; or can be covered with sand, gravel, and/or other ground-simulating material or combination of materials to a thickness of as much as 6 in. (approx. 15 cm). Models of rocks, trenches, and other obstacles can be placed on the simulated terrain. For example, for one of the Mars- Rover tests, a high-friction mat was attached to the platform, then a 6-in.- ( 15 cm) deep layer of dry, loose beach sand was deposited on the mat. The choice of these two driving surface materials was meant to bound the range of variability of terrain that the rover was expected to encounter on the Martian surface. At each of the different angles at which tests were performed, for some of the tests, rocklike concrete obstacles ranging in height from 10 to 25 cm were placed in the path of the rover (see figure). The development of the VTTP was accompanied by development of a methodology of testing to characterize the performance and modes of failure of a vehicle under test. In addition to variations in slope, ground material, and obstacles, testing typically includes driving up-slope, down-slope, cross-slope, and at intermediate angles relative to slope. Testing includes recording of drive-motor currents, wheel speeds, articulation of suspension mechanisms, and the actual path of the vehicle over the simulated terrain. The collected data can be used to

A Recepção dos Tratados Internacionais em Matéria Tributária pelo Ordenamento Jurídico Brasileiro

OpenAIRE

Bianca Castellar de Faria

2006-01-01

A presente dissertação objetiva analisar a forma de recepção dos tratados internacionais em matéria tributária pelo ordenamento jurídico brasileiro. Para isso, é fundamental verificar a relação entre o direito internacional e o direito interno, por meio da análise das teorias monista e dualista. Apresenta-se o Direito Tributário Internacional como uma das variações do Direito Internacional Público, com o objetivo de introduzir a matéria tributária. Estudam-se os tratados como uma das principa...

RER conception and it's application in RIA quality assessment

International Nuclear Information System (INIS)

Wu Defu

1998-01-01

The history, developing and applications in analysing of RIA random error are discussed. Some function expressions of RIA quality parameters are established. It supply the effective mathematic methods for the theory analysis of RIA error and the normalized quality control

Solar panel thermal cycling testing by solar simulation and infrared radiation methods

Science.gov (United States)

Nuss, H. E.

1980-01-01

For the solar panels of the European Space Agency (ESA) satellites OTS/MAROTS and ECS/MARECS the thermal cycling tests were performed by using solar simulation methods. The performance data of two different solar simulators used and the thermal test results are described. The solar simulation thermal cycling tests for the ECS/MARECS solar panels were carried out with the aid of a rotatable multipanel test rig by which simultaneous testing of three solar panels was possible. As an alternative thermal test method, the capability of an infrared radiation method was studied and infrared simulation tests for the ultralight panel and the INTELSAT 5 solar panels were performed. The setup and the characteristics of the infrared radiation unit using a quartz lamp array of approx. 15 sq and LN2-cooled shutter and the thermal test results are presented. The irradiation uniformity, the solar panel temperature distribution, temperature changing rates for both test methods are compared. Results indicate the infrared simulation is an effective solar panel thermal testing method.

Numerical simulations of capillary barrier field tests

International Nuclear Information System (INIS)

Morris, C.E.; Stormont, J.C.

1997-01-01

Numerical simulations of two capillary barrier systems tested in the field were conducted to determine if an unsaturated flow model could accurately represent the observed results. The field data was collected from two 7-m long, 1.2-m thick capillary barriers built on a 10% grade that were being tested to investigate their ability to laterally divert water downslope. One system had a homogeneous fine layer, while the fine soil of the second barrier was layered to increase its ability to laterally divert infiltrating moisture. The barriers were subjected first to constant infiltration while minimizing evaporative losses and then were exposed to ambient conditions. The continuous infiltration period of the field tests for the two barrier systems was modelled to determine the ability of an existing code to accurately represent capillary barrier behavior embodied in these two designs. Differences between the field test and the model data were found, but in general the simulations appeared to adequately reproduce the response of the test systems. Accounting for moisture retention hysteresis in the layered system will potentially lead to more accurate modelling results and is likely to be important when developing reasonable predictions of capillary barrier behavior

Trajetórias identitárias e sentidos do trabalho docente para professores universitários

Directory of Open Access Journals (Sweden)

Tânia Regina Raitz

2014-04-01

Full Text Available O presente artigo é resultado de uma pesquisa que teve como objetivo compreender a trajetória identitária profissional de seis professoras universitárias e analisar os sentidos atribuídos por elas ao trabalho docente. A investigação tratou-se, metodologicamente, de uma pesquisa qualitativa. Para tanto, foram realizadas entrevistas semiestruturadas, com o uso do gravador, em que as professoras apresentaram explicações que oferecem, ao leitor, mais elementos para a compreensão de aspectos revelados sobre suas trajetórias profissionais e sobre como significam seu trabalho docente. O tratamento das informações se deu por meio da análise de conteúdo. Os resultados mostram que os sentidos do trabalho, na contemporaneidade, aparecem diversificados, entrecruzados, ambivalentes e contraditórios. Essa diversidade se caracteriza pela complexidade da própria identidade, sempre em constituição, e também em razão de o mundo estar em constante mudança, especialmente o mundo do trabalho, que acaba por afetar o trabalho docente universitário, repercutindo também numa reconfiguração da identidade profissional.

Test Generator for MATLAB Simulations

Science.gov (United States)

Henry, Joel

2011-01-01

MATLAB Automated Test Tool, version 3.0 (MATT 3.0) is a software package that provides automated tools that reduce the time needed for extensive testing of simulation models that have been constructed in the MATLAB programming language by use of the Simulink and Real-Time Workshop programs. MATT 3.0 runs on top of the MATLAB engine application-program interface to communicate with the Simulink engine. MATT 3.0 automatically generates source code from the models, generates custom input data for testing both the models and the source code, and generates graphs and other presentations that facilitate comparison of the outputs of the models and the source code for the same input data. Context-sensitive and fully searchable help is provided in HyperText Markup Language (HTML) format.

Apontamentos sobre uma análise do discurso da crítica literária universitária

Directory of Open Access Journals (Sweden)

Grenissa STAFUZZA

2011-07-01

Full Text Available No presente artigo, tecemos alguns apontamentos sobre uma análise do discurso da crítica literária universitária mostrando uma trajetória de construção do discurso crítico acadêmico especializado na literatura. Para tanto, consideramos a transformação do gênero artigo crítico literário, de autoria de professores universitários, publicados em uma revista especializada, assim como a recepção crítica do escritor James Joyce e de sua obra, ressaltando a sua legitimação na universidade.

Apontamentos sobre uma análise do discurso da crítica literária universitária

Directory of Open Access Journals (Sweden)

Grenissa STAFUZZA

2013-10-01

Full Text Available No presente artigo, tecemos alguns apontamentos sobre uma análise do discurso da crítica literária universitária mostrando uma trajetória de construção do discurso crítico acadêmico especializado na literatura. Para tanto, consideramos a transformação do gênero artigo crítico literário, de autoria de professores universitários, publicados em uma revista especializada, assim como a recepção crítica do escritor James Joyce e de sua obra, ressaltando a sua legitimação na universidade.

Engineering of radioimmunoassay (RIA) IP10.1

International Nuclear Information System (INIS)

Hari Nurcahyadi

2010-01-01

Engineering of Radioimmunoassay (RIA) IP10.1 is an innovative by PRPN - BATAN in 2010. Innovations made to the device IP10.1 RIA is the sample changer system, sample changer system on the device RIA IP10.1 applied 2 linear axis system (X, Z) with AC servo motor. In the RIA IP10.1 also use 5 pieces of the detector, so the enumeration process 50 (Fifty) sample is expected to be faster. Like its predecessor, The whole enumeration, data collection procedures and mechanisms operating within this system is entirely controlled by a PC via an electronic module. Electronics module consists of a high voltage module, amplifier and signal processor module, the module enumerators, low-voltage module, the module driver motor controller and a USB interface. The data acquisition and communication system using a USB port with the computer. (author)

DYNREL - the reference calculation (coupled code utilization on analysis of RIA-transient)

International Nuclear Information System (INIS)

Strmensky, C.; Darilek, P.

2003-01-01

DYNREL is coupled code, comprising DYN3D and RELAP5 programs. The coupled code has been developed during four years. Now DYNREL is tested on selected RIA and thermo-hydraulic transient calculations. This material describes some results from selected RIA transient calculation (initiated by control rod movement). DYNREL modelled the whole nuclear reactors. The core is modeled as 313 or 349 independent thermo-hydraulic channels with 10 or 20 axial layers. Thermo-hydraulic part contains about 700 components that covered the six loops' model of nuclear power plant in detail. The calculated results are compared with DYN3D/M3, DYN3D/H1.1 results (Authors)

An Advanced HIL Simulation Battery Model for Battery Management System Testing

DEFF Research Database (Denmark)

Barreras, Jorge Varela; Fleischer, Christian; Christensen, Andreas Elkjær

2016-01-01

Developers and manufacturers of battery management systems (BMSs) require extensive testing of controller Hardware (HW) and Software (SW), such as analog front-end and performance of generated control code. In comparison with the tests conducted on real batteries, tests conducted on a state......-of-the-art hardware-in-the-loop (HIL) simulator can be more cost and time effective, easier to reproduce, and safer beyond the normal range of operation, especially at early stages in the development process or during fault insertion. In this paper, an HIL simulation battery model is developed for purposes of BMS...... testing on a commercial HIL simulator. A multicell electrothermal Li-ion battery (LIB) model is integrated in a system-level simulation. Then, the LIB system model is converted to C code and run in real time with the HIL simulator. Finally, in order to demonstrate the capabilities of the setup...

UPTF loop seal tests and their RELAP simulation

International Nuclear Information System (INIS)

Tuomainen, M.; Tuunanen, J.

1997-01-01

In a pressurized water reactor the loop seals have an effect on the natural circulation. If a loop seal is filled with water it can cause a flow stagnation in the loop during two-phase natural circulation. Also the pressure loss over a filled loop seal is high, which lowers the water level in the core. Tests to investigate the loop seal behaviour were performed on a German Upper Plenum Test Facility (UPTF). The purpose of the tests was to study the amount of water in the loop seal under different steam flow rates. The tests were simulated with RELAP5/MOD3.2. With high steam flow rates the code had problems in simulating the amount of the water remaining in the pump elbow, but in general the agreement between the calculated results and the experimental data was good. (orig.)

CFD simulation of air discharge tests in the PPOOLEX facility

Energy Technology Data Exchange (ETDEWEB)

Tanskanen, V.; Puustinen, M. (Lappeenranta Univ. of Technology, Nuclear Safety Research Unit (Finland))

2008-07-15

This report summarizes the CFD simulation results of two air discharge tests of the characterizing test program in 2007 with the scaled down PPOOLEX facility. Air was blown to the dry well compartment and from there through a DN200 blowdown pipe into the condensation pool (wet well). The selected tests were modeled with Fluent CFD code. Test CHAR-09-1 was simulated to 28.92 seconds of real time and test CHAR-09-3 to 17.01 seconds. The VOF model was used as a multiphase model and the standard k epsilon-model as a turbulence model. Occasional convergence problems, usually at the beginning of bubble formation, required the use of relatively short time stepping. The simulation time costs threatened to become unbearable since weeks or months of wall-clock time with 1-2 processors were needed. Therefore, the simulated time periods were limited from the real duration of the experiments. The results obtained from the CFD simulations are in a relatively good agreement with the experimental results. Simulated pressures correspond well to the measured ones and, in addition, fluctuations due to bubble formations and breakups are also captured. Most of the differences in temperature values and in their behavior seem to depend on the locations of the measurements. In the vicinity of regions occupied by water in the experiments, thermocouples getting wet and drying slowly may have had an effect on the measured temperature values. Generally speaking, most temperatures were simulated satisfyingly and the largest discrepancies could be explained by wetted thermocouples. However, differences in the dry well and blowdown pipe top measurements could not be explained by thermocouples getting wet. Heat losses and dry well / wet well heat transfer due to conduction have neither been estimated in the experiments nor modeled in the simulations. Estimation of heat conduction and heat losses should be carried out in future experiments and they should be modeled in future simulations, too. (au)

CFD simulation of air discharge tests in the PPOOLEX facility

International Nuclear Information System (INIS)

Tanskanen, V.; Puustinen, M.

2008-07-01

This report summarizes the CFD simulation results of two air discharge tests of the characterizing test program in 2007 with the scaled down PPOOLEX facility. Air was blown to the dry well compartment and from there through a DN200 blowdown pipe into the condensation pool (wet well). The selected tests were modeled with Fluent CFD code. Test CHAR-09-1 was simulated to 28.92 seconds of real time and test CHAR-09-3 to 17.01 seconds. The VOF model was used as a multiphase model and the standard k ε-model as a turbulence model. Occasional convergence problems, usually at the beginning of bubble formation, required the use of relatively short time stepping. The simulation time costs threatened to become unbearable since weeks or months of wall-clock time with 1-2 processors were needed. Therefore, the simulated time periods were limited from the real duration of the experiments. The results obtained from the CFD simulations are in a relatively good agreement with the experimental results. Simulated pressures correspond well to the measured ones and, in addition, fluctuations due to bubble formations and breakups are also captured. Most of the differences in temperature values and in their behavior seem to depend on the locations of the measurements. In the vicinity of regions occupied by water in the experiments, thermocouples getting wet and drying slowly may have had an effect on the measured temperature values. Generally speaking, most temperatures were simulated satisfyingly and the largest discrepancies could be explained by wetted thermocouples. However, differences in the dry well and blowdown pipe top measurements could not be explained by thermocouples getting wet. Heat losses and dry well / wet well heat transfer due to conduction have neither been estimated in the experiments nor modeled in the simulations. Estimation of heat conduction and heat losses should be carried out in future experiments and they should be modeled in future simulations, too. (au)

Development of ECR ion source and LEBT technology for RIA

International Nuclear Information System (INIS)

Leitner, Daniela; Lyneis, Claude M.; Abbott, Steven R.; Dwinell, Roger D.; Leitner, Matthaeus; Silver, Charles S.; Taylor, Clyde E.

2004-01-01

The Rare Isotope Accelerator (RIA) Linac driver requires a great variety of high charge state ion beams with up to a magnitude higher intensity than currently achievable for the heaviest masses. The goal of the RIA injector R and D program for VENUS is the reliable production of intense medium charge state ion beams, e.g., 8 puA (particle mu A) of U29+. Therefore, the superconducting ECR ion source VENUS has been designed from the beginning for optimum operation at 28 GHz at high power (10 kW). In addition, a high intensity Low Energy Beam Transport, LEBT, that was developed to analyze and transport these multiply-charged, space charge dominated beams. During the last year VENUS was commissioned at 18 GHz and preparations for 28 GHz operation continued. Tests with various gases and recently metals have been performed with up to 2000 W of 18 GHz RF power. Promising performance has been measured in those preliminary beam tests. For example, 180 p mu A of O6+, 15 p mu A of Ar12+, 7.5 puA of X e20+ and 4puA of Bi24+ were produced in the early commissioning phase, ranking VENUS among the currently highest performance 18 GHz ECR ion sources. In FY04 a 10 kW 28 gyrotron system will be added, which will enable VENUS to reach full performance. The emittance of the beams produced at 18 GHz was measured with a two axis emittance scanner developed with earlier RIA R and D funds

Finite Element Simulation of Fracture Toughness Test

International Nuclear Information System (INIS)

Chu, Seok Jae; Liu, Cong Hao

2013-01-01

Finite element simulations of tensile tests were performed to determine the equivalent stress - equivalent plastic strain curves, critical equivalent stresses, and critical equivalent plastic strains. Then, the curves were used as inputs to finite element simulations of fracture toughness tests to determine the plane strain fracture toughness. The critical COD was taken as the COD when the equivalent plastic strain at the crack tip reached a critical value, and it was used as a crack growth criterion. The relationship between the critical COD and the critical equivalent plastic strain or the reduction of area was found. The relationship between the plane strain fracture toughness and the product of the critical equivalent stress and the critical equivalent plastic strain was also found

Memória e justiça: o negacionismo e a falsificação da história

Directory of Open Access Journals (Sweden)

Odilon Caldeira Neto

2009-12-01

Full Text Available O presente artigo busca analisar os embates gerados dentro do processo de formação e transformação das memórias coletivas, em especial no caso da memória das vítimas e sobreviventes da Segunda Guerra Mundial, particularmente com o Holocausto (Shoah. Procura ainda compreender como se dá o surgimento de teses que afirmam a inexistência do Holocausto e da existência de um suposto complô judaico de dominação mundial, ou seja, o fenômeno negacionista e os reflexos desta prática no Brasil, assim como os esforços de diversas categorias profissionais em salvaguardar a memória e a disciplina histórica das ameaças de falsificações intole-rantes e discriminatórias.

The Relationship between Tests of Neurocognition and Performance on a Laparoscopic Simulator

Directory of Open Access Journals (Sweden)

Oumar Kuzbari

2010-01-01

Full Text Available Objective. To estimate if there is a relationship between the results of tests of neurocognition and performance on a laparoscopic surgery simulator. Methods and Materials. Twenty participants with no prior laparoscopic experience had baseline cognitive tests administered (Trail Making Test, Part A and B (TMT-A and TMT-B, Grooved Peg Board Test, Symbol Digit Modalities Test, Symbol Digit Recall Test, and Stroop Interference Test, completed a demographic questionnaire, and then performed laparoscopy using a simulator. We correlated the results of cognitive tests with laparoscopic surgical performance. Results. One cognitive test sensitive to frontal lobe function, TMT-A, significantly correlated with laparoscopic surgical performance on the simulator (correlation coefficient of 0.534 with P<.05. However, the correlation between performance and other cognitive tests (TMT-B, Grooved Peg Board Test, Symbol Digit Modalities Test, Symbol Digit Recall Test, and Stroop Interference Test was not statistically significant. Conclusion. Laparoscopic performance may be related to measures of frontal lobe function. Neurocognitive tests may predict motor skills abilities and performance on laparoscopic simulator.

Deposition Velocities of Non-Newtonian Slurries in Pipelines: Complex Simulant Testing

Energy Technology Data Exchange (ETDEWEB)

Poloski, Adam P.; Bonebrake, Michael L.; Casella, Andrew M.; Johnson, Michael D.; Toth, James J.; Adkins, Harold E.; Chun, Jaehun; Denslow, Kayte M.; Luna, Maria; Tingey, Joel M.

2009-07-01

One of the concerns expressed by the External Flowsheet Review Team (EFRT) is about the potential for pipe plugging at the Waste Treatment and Immobilization Plant (WTP). Per the review’s executive summary, “Piping that transports slurries will plug unless it is properly designed to minimize this risk. This design approach has not been followed consistently, which will lead to frequent shutdowns due to line plugging.” To evaluate the potential for plugging, deposition-velocity tests were performed on several physical simulants to determine whether the design approach is conservative. Deposition velocity is defined as the velocity below which particles begin to deposit to form a moving bed of particles on the bottom of a straight horizontal pipe during slurry-transport operations. The deposition velocity depends on the system geometry and the physical properties of the particles and fluid. An experimental program was implemented to test the stability-map concepts presented in WTP-RPT-175 Rev. 01. Two types of simulant were tested. The first type of simulant was similar to the glass-bead simulants discussed in WTP-RPT-175 Rev. 0 ; it consists of glass beads with a nominal particle size of 150 µm in a kaolin/water slurry. The initial simulant was prepared at a target yield stress of approximately 30 Pa. The yield stress was then reduced, stepwise, via dilution or rheological modifiers, ultimately to a level of <1 Pa. At each yield-stress step, deposition-velocity testing was performed. Testing over this range of yield-stress bounds the expected rheological operating window of the WTP and allows the results to be compared to stability-map predictions for this system. The second simulant was a precipitated hydroxide that simulates HLW pretreated sludge from Hanford waste tank AZ-101. Testing was performed in a manner similar to that for the first simulant over a wide range of yield stresses; however, an additional test of net-positive suction-head required (NPSHR

25th Space Simulation Conference. Environmental Testing: The Earth-Space Connection

Science.gov (United States)

Packard, Edward

2008-01-01

Topics covered include: Methods of Helium Injection and Removal for Heat Transfer Augmentation; The ESA Large Space Simulator Mechanical Ground Support Equipment for Spacecraft Testing; Temperature Stability and Control Requirements for Thermal Vacuum/Thermal Balance Testing of the Aquarius Radiometer; The Liquid Nitrogen System for Chamber A: A Change from Original Forced Flow Design to a Natural Flow (Thermo Siphon) System; Return to Mercury: A Comparison of Solar Simulation and Flight Data for the MESSENGER Spacecraft; Floating Pressure Conversion and Equipment Upgrades of Two 3.5kw, 20k, Helium Refrigerators; Affect of Air Leakage into a Thermal-Vacuum Chamber on Helium Refrigeration Heat Load; Special ISO Class 6 Cleanroom for the Lunar Reconnaissance Orbiter (LRO) Project; A State-of-the-Art Contamination Effects Research and Test Facility Martian Dust Simulator; Cleanroom Design Practices and Their Influence on Particle Counts; Extra Terrestrial Environmental Chamber Design; Contamination Sources Effects Analysis (CSEA) - A Tool to Balance Cost/Schedule While Managing Facility Availability; SES and Acoustics at GSFC; HST Super Lightweight Interchangeable Carrier (SLIC) Static Test; Virtual Shaker Testing: Simulation Technology Improves Vibration Test Performance; Estimating Shock Spectra: Extensions beyond GEVS; Structural Dynamic Analysis of a Spacecraft Multi-DOF Shaker Table; Direct Field Acoustic Testing; Manufacture of Cryoshroud Surfaces for Space Simulation Chambers; The New LOTIS Test Facility; Thermal Vacuum Control Systems Options for Test Facilities; Extremely High Vacuum Chamber for Low Outgassing Processing at NASA Goddard; Precision Cleaning - Path to Premier; The New Anechoic Shielded Chambers Designed for Space and Commercial Applications at LIT; Extraction of Thermal Performance Values from Samples in the Lunar Dust Adhesion Bell Jar; Thermal (Silicon Diode) Data Acquisition System; Aquarius's Instrument Science Data System (ISDS) Automated

Investigating the Problem Solving Competency of Pre Service Teachers in Dynamic Geometry Environment

Science.gov (United States)

Haja, Shajahan

2005-01-01

This study investigated the problem-solving competency of four secondary pre service teachers (PSTs) of University of London as they explored geometry problems in dynamic geometry environment (DGE) in 2004. A constructivist experiment was designed in which dynamic software Cabri-Geometre II (hereafter Cabri) was used as an interactive medium.…

Malária grave importada: relato de caso Severe imported malaria: case report

Directory of Open Access Journals (Sweden)

Alessandra Alves

2007-06-01

Full Text Available JUSTIFICATIVA E OBJETIVOS: A malária ainda representa um problema de saúde global. A forma grave da doença é causada principalmente por P. falciparum e pode cursar com complicações cerebrais, renais, pulmonares, hematológicas, circulatórias e hepáticas. O objetivo deste estudo foi relatar um caso de paciente portador de malária grave importada. RELATO DO CASO: Paciente do sexo masculino, 30 anos, pardo, filipino, marinheiro, proveniente de embarcação vinda da Nigéria, com história de dor abdominal no hipocôndrio direito, icterícia, febre e rebaixamento do nível de consciência. Os exames laboratoriais de admissão mostraram hiperbilirrubinemia de 50 mg/dL, acidose metabólica grave, trombocitopenia, creatinina de 5,6 mg/dL, leucocitose com desvio até metamielócitos. O escore APACHE II foi de 37, com risco de óbito de 88%. Durante a internação foi diagnosticada malária por P. falciparum pelo teste de gota espessa. Mesmo com tratamento antimalárico adequado, o paciente evoluiu com insuficiência renal aguda necessitando de hemodiálise e síndrome de angústia respiratória aguda (SARA, necessitando de ventilação mecânica (VM, choque refratário tratado com aminas vasoativas, além de quadro hematológico, configurando um caso grave de disfunção de múltiplos de órgãos. Ainda apresentou pneumonia associada à VM e sepse relacionada ao uso de cateteres. Após a alta hospitalar, o paciente não apresentou seqüelas cerebral, pulmonar ou renal. CONCLUSÕES: Dos critérios definidores de malária grave descritos na literatura, o paciente preenchia: insuficiência renal aguda, síndrome da angústia respiratória aguda (SARA, acidose metabólica, alteração do nível de consciência, hemoglobinúria macroscópica, hiperparasitemia e hiperbilirrubinemia, que se relaciona a uma mortalidade maior que 10%, na dependência do tratamento precoce e dos recursos disponíveis. A malária grave exige diagnóstico e tratamento

Aspectos actuais da hipertensão arterial pulmonar: primária e secundária

Directory of Open Access Journals (Sweden)

Emilia Álvares

1997-01-01

Full Text Available RESUMO: A situação patológica mais importante na circulação pulmonar é o desenvolvimeoto da Hipertensão Arterial Pulmonar, que pode resultar de doença parenquimatosa pulmonar, alterações da parede vascular ou da obstrução do lúmen por trombose ou embolia.Procurouse com este trabalho, fazer uma revisão actual da literatura médica acerca da hipertensão arterial pulmonar primária e secundária.Debruçãmos-nos essencialmente, sobre os seus cooceitos fisiopatológicos, critérios diagnósticos e aspectos terapêuticos mais recentes. ABSTRACT: The most important response of pulmonary blood vessels to disease is the development of increased pulmonary arterial pressure that may result from parenchymal disease of the lungs, changes in the walls of the blood vessels or obstruction to the lumen caused by thrombosis or embolization.The aim of the authors in this study, was to make a actual review of the medical literature about of primary and secondary pulmonary hypertension.We report about this entity, essentially physiopatologic concepts, diagnosis approach and therapeutics aspects, more recent. Palavras-chave: Hipertensão Pulmonar, Primária, Secundária, Classificação, Tratamento, Key-words: Pulmonary Hypertension, Primary, Secondary, Classification, Therapeutic

Memórias perdidas, identidades sem cidadania

Directory of Open Access Journals (Sweden)

Ungulani Ba Ka Khosa

2015-04-01

Full Text Available Este texto procura contribuir para o debate sobre as políticas identitárias no Moçambique contemporâneo. Contrapondo, através de vários exemplos, a diversidade identitária do tecido social do país à altivez ignorante das estruturas de poder nele presentes, o texto procura problematizar, em vários momentos históricos, a fratura cognitiva entre o projeto político nacional, conceptualizado a partir das elites que controlam o Estado, e o plurilinguismo e a polifonia que constroem o tecido social real. A partir desta dicotomia o texto explora o discurso sobre a nação a várias vozes, problematizando os sentidos das lições da história de Moçambique e os múltiplos silenciamentos que a narrativa histórica dominante vem realizando.

Reprodutibilidade do teste de caminhada de 6 minutos e marcadores autonômicos cardíacos em idosas ativas e sedentárias

Directory of Open Access Journals (Sweden)

André Igor Fonteles

2016-07-01

Full Text Available DOI: http://dx.doi.org/10.5007/1980-0037.2016v18n3p287   Objetivou-se verificar a reprodutibilidade do teste de caminhada de 6 minutos (TC6 e de marcadores autonômicos cardíacos pós-esforço em idosas fisicamente ativas e sedentárias. Dezoito idosas ativas (64,2 ± 3,1 anos; 63,0 ± 2,7 kg; 1,52 ± 0,06 m; 26,9 ± 2,7 kg.m-2 praticantes de Tai Chi Chuan (≥6 meses de prática e 18 idosas sedentárias (64,0 ± 3,7 anos; 63,8 ± 8,9 kg; 1,49 ± 0,05 m; 28,4 ± 3,5 kg.m-2 foram submetidas a dois TC6 com uma semana de intervalo. Foram medidas a frequência cardíaca de recuperação (FCR de um e dois minutos (FCR1’ e FCR2’, respectivamente e variabilidade da frequência cardíaca (VFC pós-esforço. A reprodutibilidade foi verificada pelos: coeficiente de correlação intraclasse (CCI com 95% de intervalo de confiança; análise de concordância de Bland-Altman; e coeficiente de variação (CV. O desempenho no TC6 (528,8±71,4 m e 473,2±62,4 m; CV=7,9% e CV=8,5% apresentou alta reprodutibilidade (CCI=0,86 em idosas ativas e sedentárias, respectivamente. Similarmente, as medidas pós-esforço da FCR1’ (29,0±11,0 bpm e 17,0±8,0 bpm; CV=30,1% e CV=40,2% e FCR2’ (36,0±10,0 bpm e 24,0±9,0 bpm; CV=23,7% e CV=22,8% apresentaram alta reprodutibilidade (CCI≥0,84 e CCI≥0,80 em ambos os grupos. Quanto a VFC verificou-se reprodutibilidade moderada (CCI≥0,57; CV=35-47% em idosas ativas e moderada-alta nas sedentárias (CCI=0,65-0,76; CV=34-69%. Todas as variáveis apresentaram concordância em ambos os grupos. Conclui-se que o TC6, FCR e VFC pós-esforço são instrumentos reprodutíveis na avaliação da capacidade funcional e controle autonômico cardíaco em idosas ativas e sedentárias.

Olhar do cronista, registro da memória

Directory of Open Access Journals (Sweden)

Angela Maria Dutra da Silva Senra

2016-09-01

Full Text Available Propomos apresentar a pesquisa “Rastros da memória literária em crônicas dos jornais marianenses dos séculos XIX e XX” (PERPÉTUA, 2015, que tem como fonte um acervo de periódicos da cidade de Mariana (MG, hoje sob a guarda do Centro de Pesquisas Linguagem, Memória e Tradução do ICHS-UFOP. Dada a evidente relação desse acervo com a memória sociocultural da cidade, nossa pesquisa, em andamento, volta-se objetivamente para identificar e selecionar crônicas literárias publicadas nos periódicos, com a subsequente análise em sua correlação com a memória da região, sob as bases de um significativo material teórico sobre esse gênero. Assim, com vistas a adentrar no passado memorial da cidade de Mariana, apresentaremos o resultado parcial da nossa investigação, que tem proporcionado o conhecimento acerca da crônica; e do registro memorial dessa cidade em razão de sua importância no cenário histórico, social e cultural de Minas Gerais.

Vilas operárias e higienismo na cidade de Vitória, as iniciativas governamentais no Espírito Santo - Brasil

Directory of Open Access Journals (Sweden)

Dra. Arq. Luciana Nemer Diniz

2015-12-01

Full Text Available As vilas operárias foram a materialização habitacional da política higienista promovida pelos governos para a transformação das cidades - novos padrões funcionais e formais. O processo de industrialização foi propulsor dessas alterações em busca de um habitat operário compatível com as necessidades básicas de reprodução da força de trabalho. A participação de médicos e engenheiros sanitaristas norteou as reformas urbanas. Em Vitória o engenheiro Saturnino de Brito projetou o “Novo Arrabalde” em 1896 onde previu duas vilas operárias. A construção de moradia para os empregados remete ao período da escravidão, porém na cidade as vilas operárias estão relacionadas ao período industrial e como o café permaneceu por mais tempo como principal produto da economia capixaba as vilas surgiram a partir da primeira década do século XX. Em Vitória a formação de cortiços foi tímida e não houve corrida no início do século passado por habitação na região central. O aterro e loteamento do Campinho, concluído em 1912 e a construção de vinte e oito casas para funcionários estatais em suas imediações foram às primeiras iniciativas do governo relacionadas à habitação operária na cidade. As vilas operárias em Vitória, suas causas e simbolismos são análises que o presente trabalho propõe-se realizar

A Coupling Vibration Test Bench and the Simulation Research of a Maglev Vehicle

Directory of Open Access Journals (Sweden)

Weihua Ma

2015-01-01

Full Text Available To study the characteristics of the coupling vibration between a maglev vehicle and its track beam system and to improve the performance of the levitation system, a new type of vibration test bench was developed. Take a single maglev frame as the study object; simulation of the coupling vibration of the maglev vehicle, levitation system, and track beam were achieved. In addition, all types of real track irregularity excitations can be simulated using hydraulic actuators of the test bench. To expand the research scope, a simulation model was developed that can conduct the simulation research synergistically with the test bench. Based on a dynamics model of the test bench, the dynamics simulation method determined the influence on the levitation control performance of three factors: the track beam support stiffness, the track beam mass, and the track irregularity. The vibration resonance phenomenon of the vehicle/track system was reproduced by the dynamics simulation, and a portion of the simulation results were validated by the test results. By combining the test bench and the dynamics model, experiments can be guided by the simulation results, and the experimental results can validate the dynamics simulation results.

Psicologia Comunitária: uma abordagem conceitual

OpenAIRE

Gomes, Antonio Maspoli de Araujo

2009-01-01

Este artigo apresenta as principais tentativas de conceituação das correntes teóricas sobre a psicologia comunitária, ligadas a psicologia social. A partir da análise dos dados obtidos podemos afirmar que a Psicologia Comunitária é um saber em construção, pragmático, derivado da Psicologia Social. Concluímos também que muitas das teorias referenciadas e das técnicas citadas pelos psicólogos que trabalham em Psicologia Comunitária são derivadas dos referenciais teóricos da Psicologia Comunitár...

Memórias sobre a história de uma cidade: a História como labirinto Memories about the history of a city: the history as a labyrinth

Directory of Open Access Journals (Sweden)

Lana Mara de Castro Siman

2008-06-01

Full Text Available Neste artigo, desenvolve-se a argumentação de que a escrita da história de cidades elaborada por meio do diálogo entre a memória e a História pode oferecer possibilidades de aprendermos a nelas nos perder para nelas nos reencontrar, num tempo labirintítico. A idéia do labirinto é inspirada em Walter Benjamin (1985, 1994 e em outros que trabalham nessa tradição teórica e representa uma contraposição à compreensão do tempo histórico forjado na modernidade. Enquanto este é linear, vazio, homogêneo, o tempo labirintítico é múltiplo, não-linear, repleto de possibilidades inscritas nas relações do presente com passado e futuro. Para decifrá-lo, é necessária a aprendizagem da leitura indiciária - dos sinais, dos signos, das ruínas, das marcas, dos gestos, dos silêncios, - deixados pela ação dos homens e relatados pelos seus testemunhos. É, também, em Benjamin que se apóia a idéia de que a história como labirinto é contada pelo narrador que narra a sua experiência histórica. A escrita híbrida da história - entre a História e a memória -, base para o desenvolvimento da referida argumentação, é fruto de uma pesquisa com fontes orais e outros conhecimentos históricos, elaborada para uma dissertação de mestrado defendida pela autora do artigo, sobre a história de Governador Valadares, Minas Gerais.In this article, it is developed an argumentation concerning the writing of the history of the cities being elaborated through the dialogue between the memory and the History. This argumentation is based on the idea of this kind of writing offer possibilities of learning to lose ourselves inside the memory and the History and to find ourselves again through them, in a labyrinth time. The idea of the labyrinth is inspired in Walter Benjamim (1985,1994 as well in others who work in this theoretical line. It represents a counter-position to the understanding of historical time constructed in modern time. While the

Oralidade e memória: o registro audiovisual de A história de Lélio e Lina de Guimarães Rosa

Directory of Open Access Journals (Sweden)

Eleni Ferreira de Souza Gonçalves

2016-09-01

Full Text Available Este trabalho aborda as questões da memória e da oralidade na narrativa de Guimarães Rosa. Adotamos uma análise comparativa entre a novela A história de Lélio e Lina e o respectivo registro oral – em forma de documentário – feito pelos Grupos de Contadores de Histórias de Cordisburgo e do Morro da Garça, em Minas Gerais. Analisamos no texto roseano transposto para o suporte audiovisual o que se mantém em um e outro e verificamos os possíveis efeitos que causam ao leitor e ao espectador. Na transposição, se a memória do texto escrito permanece, os elementos da oralidade e da memória sertaneja adquirem outra dimensão na fala dos narradores. Referenciamo-nos no livro A memória Coletiva, de Maurice Halbwachs, e na entrevista de Guimarães Rosa a Gunter Lorenz, na qual o escritor enfatiza aspectos decisivos de sua escrita, sua relação com a língua e linguagem e sua memória em relação ao sertão.

The use of electron beam in RIA R and D

International Nuclear Information System (INIS)

Gomes, Itacil C.; Nolen, Jerry; Reed, Claude

2004-01-01

This paper discusses two electron beam applications for the RIA (Rare Isotope Accelerator) R and D. The first is for simulating energy deposition of heavy ions on lithium jets. The peak energy deposition for a 400-kW uranium beam will be 4 MW/cm 3 . Calculations have shown that a 1-MeV electron beam with 40mA of current has a peak energy deposition about 4 MW/cm 3 making it suitable to mimic the thermal response of lithium jet at that uranium beam heat load. The second application of electron beams for RIA R and D, discussed in this paper, is the use of low energy electron beam as a diagnosis tool for on-line monitoring of thickness variations of thin foils or thin jets. Thin foils can be corroded and jets might experience instabilities that can compromise their functionality. Low energy electron beams can be used to detect any change in thickness enabling a continuous on-line monitoring of the thin film being monitored. Calculations have indicated that variations in lithium jet thicknesses at the micron level can easily be detected

Test methods and load simulation at roller test stand; Pruefmethoden und Lastsimulation auf Rollenpruefstaenden

Energy Technology Data Exchange (ETDEWEB)

Engelmann, Juergen [BMW AG, Muenchen (Germany); Koenig, Manfred [VISPIRON AG, Muenchen (Germany)

2012-11-01

The development of vehicles is a time expensive process and requires a worldwide mobility, since the vehicles are tested for different environmental conditions, which only occur in specified regions and within predefined seasonal periods. To become independent of weather conditions and the local and seasonal variation, it is necessary to shift particular tests to a climatic wind tunnel. Although this offers an ideal environment for precise and reproducible results, many tests need to be performed in order to acquire knowledge about the differences between real road investigations and wind tunnel experiments. It is the work of Method developers to properly transfer specified road tests to the test facility such that comparable results are obtained. These details will be discussed in the first chapter. An important aspect, within this objective, is the realistic simulation of drive resistance on the road by dynamometers. Therefore the different forces, contributing to the drive resistance on the road, are determined in order to simulate the realistic load on the vehicle drive train by the electric drive units of the dynamometers. To increase the accuracy of the load simulation, a special feature has been added to the dyno-control. This feature includes the influence of air-density on the drive resistance at a given environmental temperature, pressure and humidity. (orig.)

A mechanical breathing simulator for respirator test

International Nuclear Information System (INIS)

Murata, Mikio; Ikezawa, Yoshio; Yoshida, Yoshikazu

1976-01-01

A mechanical breathing simulator has been developed to produce the human respiration for use in respirator test. The respirations were produced through the strokes of piston controlled by a rockerarm with adjustable fulcrum. The respiration rate was governed by motor-speed control, independent of the tidal volume achieved by adjustment of the piston stroke. By the breather, the simulated respirations for work rate 0, 208, 415, 622 and 830 kg-m/min could be produced through the typical dummy head. (auth.)

Computer simulation of ultrasonic testing for aerospace vehicle

Energy Technology Data Exchange (ETDEWEB)

Yamawaki, H [National Institute for Materials Science, 1-2-1, Sengen, 305-0047 Tsukuba (Japan); Moriya, S; Masuoka, T [Japan Aerospace Exploration Agency, 1 Koganesawa, Kimigawa, 981-1525 Kakuda (Japan); Takatsubo, J, E-mail: yamawaki.hisashi@nims.go.jp [Advanced Industrial Science and Technology, AIST Tsukuba Central 2, 1-1-1 Umezono, 305-8568 Tsukuba (Japan)

2011-01-01

Non-destructive testing techniques are developed to secure reliability of aerospace vehicles used repetitively. In the case of cracks caused by thermal stress on walls in combustion chambers of liquid-fuel rockets, it is examined by ultrasonic waves visualization technique developed in AIST. The technique is composed with non-contact ultrasonic generation by pulsed-laser scanning, piezoelectric transducer for the ultrasonic detection, and image reconstruction processing. It enables detection of defects by visualization of ultrasonic waves scattered by the defects. In NIMS, the condition of the detection by the visualization is investigated using computer simulation for ultrasonic propagation that has capability of fast 3-D calculation. The simulation technique is based on finite-difference method and two-step elastic wave equations. It is reported about the investigation by the calculation, and shows availability of the simulation for the ultrasonic testing technique of the wall cracks.

Reprodutibilidade da atividade eletromiográfica em usuários de próteses totais durante simulação de atividades de vida diária = Reliability of EMG activity in complete denture users during simulation of activities of daily living

Directory of Open Access Journals (Sweden)

Baldisserotto, Simone Michielon

2010-01-01

Full Text Available da atividade eletromiográfica dos músculos mastigatórios (m. temporal e m. masseter, posturais do pescoço (mm. esternocleidomastoideo e trapézio, posturais do tronco (mm. reto abdominal e paravertebrais e de força das extremidades inferiores (mm. reto femoral e gastrocnemius medial durante simulação de atividades de vida diária (AVDs. Metodologia: A amostra foi constituída por dez mulheres saudáveis, usuárias de prótese total bimaxilar, com idade média de 58,2 anos. Foram realizados três testes AVDs: levantar/sentar da cadeira (TCAD, levantar/deitar na cama (TCAM e pegar/largar sacolas (TSAC. A reprodutibilidade dos valores EMG foi analisada por teste-reteste. Para cada teste AVD foram estimados coeficiente de correlação intraclasse (CCIC e intervalo de confiança de 95% com estratificação por músculo, condição com e sem prótese (suporte oclusal e movimento durante o teste, considerando três repetições por sujeito para avaliar consistência. Resultados: Todos os grupos musculares apresentaram ativação durante os testes simulando AVDs. O método utilizado mostrou reprodutibilidade satisfatória com CCICs considerados moderados a altos. Os maiores valores de CCIC foram estimados para os m. esternocleidomastoideo (0,82 a 0,97 e m. paravertebrais (0,86 a 0,99. Conclusão: Os resultados sugerem que o método de EMG cinesiológico descrito apresentou reprodutibilidade satisfatória nesta amostra

Results of Aging Tests of Vendor-Produced Blended Feed Simulant

International Nuclear Information System (INIS)

Russell, Renee L.; Buchmiller, William C.; Cantrell, Kirk J.; Peterson, Reid A.; Rinehart, Donald E.

2009-01-01

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is procuring through Pacific Northwest National Laboratory (PNNL) a minimum of five 3,500 gallon batches of waste simulant for Phase 1 testing in the Pretreatment Engineering Platform (PEP). To make sure that the quality of the simulant is acceptable, the production method was scaled up starting from laboratory-prepared simulant through 15-gallon vendor prepared simulant and 250-gallon vendor prepared simulant before embarking on the production of the 3500-gallon simulant batch by the vendor. The 3500-gallon PEP simulant batches were packaged in 250-gallon high molecular weight polyethylene totes at NOAH Technologies. The simulant was stored in an environmentally controlled environment at NOAH Technologies within their warehouse before blending or shipping. For the 15-gallon, 250-gallon, and 3500-gallon batch 0, the simulant was shipped in ambient temperature trucks with shipment requiring nominally 3 days. The 3500-gallon batch 1 traveled in a 70-75 F temperature controlled truck. Typically the simulant was uploaded in a PEP receiving tank within 24-hours of receipt. The first uploading required longer with it stored outside. Physical and chemical characterization of the 250-gallon batch was necessary to determine the effect of aging on the simulant in transit from the vendor and in storage before its use in the PEP. Therefore, aging tests were conducted on the 250-gallon batch of the vendor-produced PEP blended feed simulant to identify and determine any changes to the physical characteristics of the simulant when in storage. The supernate was also chemically characterized. Four aging scenarios for the vendor-produced blended simulant were studied: (1) stored outside in a 250-gallon tote, (2) stored inside in a gallon plastic bottle, (3) stored inside in a well mixed 5-L tank, and (4) subject to extended temperature cycling under summer temperature conditions in a gallon plastic bottle. The following

Panorama da estrutura presidiária brasileira

Directory of Open Access Journals (Sweden)

Renata de Oliveira Cartaxo

2013-06-01

Full Text Available Objetivo: Descrever, a partir do Sistema Integrado de Informações Penitenciárias – Infopen, aspectos da estrutura prisional nacional, características dos apenados e perfil dos profissionais existentes para garantir o preceito constitucional de assistência à saúde. Métodos: Estudo descritivo, de base documental, realizado a partir de dados secundários disponíveis no Sistema Integrado de Informações Penitenciárias, no qual analisaram-se a estrutura carcerária brasileira, o perfil do apenado no que tange a características pessoais e do crime cometido, e os profissionais envolvidos na assistência à saúde. Resultados: Constata-se que existem 298.275 vagas, ocupadas por 496.251 presos nos 1.857 estabelecimentos penais. No tocante ao perfil dos presos, verifica-se que 92,3% (461.444 são do sexo masculino, na faixa etária entre 18 e 24 anos (25,6% - 126.929, da cor parda (36,7% - 82.354, comensino fundamental incompleto (40,7% - 201.938, que cometeram, principalmente, o crime de tráfico de entorpecentes (23,5% - 100.648. Quanto à composição da equipe de assistência à saúde, evidencia-se um total de 5.132 profissionais registrados no sistema. Conclusão: Constata-se, a partir do sistema integrado de informações penitenciárias, que a estrutura carcerária brasileira se caracteriza por apresentar um déficit de vagas, ocasionada pelasuperlotação e/ou saturação dos estabelecimentos existentes, o que dificulta, em especial, a garantia do atendimento às necessidades de saúde dos apenados.

Políticas Públicas de Memória O Programa Pontos de Memória no Contexto Sul-Rio-Grandense

Directory of Open Access Journals (Sweden)

Mariana Boujadi Mariano da Silva

2016-12-01

Full Text Available O presente estudo busca realizar uma análise do Programa Pontos de Memória, do Instituto Brasileiro de Museus. Analisando o Programa, observa-se a iniciativa de preservar a memória de determinados grupos sociais considerados excluídos da representação de museus ditos tradicionais, através da implementação de espaços de memória ou ações sociomuseológicas, que narrem suas histórias a partir do suporte de patrimônios locais. A análise parte de questionamentos iniciais: quais são as memórias e as identidades que o Programa seleciona para narrar, através de quais ferramentas ocorre a divulgação e sobretudo a apropriação deste patrimônio por parte da comunidade? Para analisar as causas e os efeitos desta política pública, o trabalho observará e discutirá o alcance e a influência que esses espaços exercem nas comunidades, as ações desenvolvidas e a longevidade desses espaços ou ações no contexto sul-rio-grandense.

A história cultural e as fontes de pesquisa

Directory of Open Access Journals (Sweden)

Alboni Marisa Dudeque Pianovski Vieira

2015-07-01

Full Text Available Na primeira metade do século XX, a história “abriu-se” para as demais ciências, com uma proposta de diálogo interdisciplinar. O campo historiográfico, então, sofreu mudança significativa, obrigando os historiadores a reconsiderar o conceito de fontes, para além daquelas predominantemente documentais, na pesquisa em história. Sobre essas fontes de pesquisa incide a reflexão, considerando-se a contribuição que os avanços tecnológicos trazem à coleta de dados, em particular, na história oral. Do ponto de vista metodológico, trata-se de estudo de caso, com caráter bibliográfico, que traça uma retrospectiva da história cultural, enfatizando as possibilidades de uso da história oral. Como aporte teórico, foram consultados estudos de Ribeiro (2003, Pesavento (2005 e Alberti (2005. Os resultados apontam para possibilidades de utilização da história oral na pesquisa em história cultural.

FRACTIONAL CRYSTALLIZATION LABORATORY TESTS WITH SIMULATED TANK WASTE

International Nuclear Information System (INIS)

HERTING DL

2007-01-01

Results are presented for several simulated waste tests related to development of the fractional crystallization process. Product salt dissolution rates were measured to support pilot plant equipment design. Evaporation tests were performed to evaluate the effects of organics on slurry behavior and to determine optimum antifoam addition levels. A loss-of-power test was performed to support pilot plant accident scenario analysis. Envelope limit tests were done to address variations in feed composition

Radiation Simulations and Development of Concepts for High Power Beam Dumps, Catchers and Pre-separator Area Layouts for the Fragment Separators for RIA

CERN Document Server

Ronningen, Reginald; Beene, James R; Blideanu, Valetin; Boles, Jason; Bollen, Georg; Burgess, Thomas; Carter, Ken; Conner, David L; Gabriel, Tony A; Geissel, Hans; Gomes, Itacil C; Heilbronn, Lawrence; Iwase, Hiroshi; Lawton, Don; Levand, Anthony; Mansur, Louis; Momozaki, Yoichi; Morrissey, David; Nolen, Jerry; Reed, Claude; Remec, Igor; Rennich, Mark; Reyes, Susana; Sherrill, Bradley; Stein, Werner; Stoyer, Mark; Stracener, Dan; Wendel, Mark; Zeller, Al

2005-01-01

The development of high-power beam dumps and catchers, and pre-separator layouts for proposed fragment separators of the Rare-Isotope Accelerator (RIA) facility are important in realizing how to handle the 400 kW in the primary beam. We will present examples of pre-conceptual designs of beam dumps, fragment catchers, and the pre-separator layout. We will also present examples of ongoing work on radiation simulations using the heavy-ion-transport code PHITS, characterizing the secondary radiation produced by the high-power ion beams interacting with these devices. Results on radiation heating of targets, magnet coils, associated hardware and shielding, component activation, and levels of radiation dose will be presented. These initial studies will yield insight into the impact of the high-power dissipation on fragment separator design, remote handling concepts, nuclear safety and potential facility hazard classification, shielding design, civil construction design, component design, and material choices. Furth...

7th Conference Simulation and Testing for Vehicle Technology

CERN Document Server

Riese, Jens; Rüden, Klaus

2016-01-01

The book includes contributions on the latest model-based methods for the development of personal and commercial vehicle control devices. The main topics treated are: application of simulation and model design to development of driver assistance systems; physical and database model design for engines, motors, powertrain, undercarriage and the whole vehicle; new simulation tools, methods and optimization processes; applications of simulation in function and software development; function and software testing using HiL, MiL and SiL simulation; application of simulation and optimization in application of control devices; automation approaches at all stages of the development process.

Validation of the U.S. NRC coupled code system TRITON/TRACE/PARCS with the special power excursion reactor test III (SPERT III)

Energy Technology Data Exchange (ETDEWEB)

Wang, R. C.; Xu, Y.; Downar, T. [Dept. of Nuclear Engineering and Radiological Sciences, Univ. of Michigan, Ann Arbor, MI 48104 (United States); Hudson, N. [RES Div., U.S. NRC, Rockville, MD (United States)

2012-07-01

The Special Power Excursion Reactor Test III (SPERT III) was a series of reactivity insertion experiments conducted in the 1950's. This paper describes the validation of the U.S. NRC Coupled Code system TRITON/PARCS/TRACE to simulate reactivity insertion accidents (RIA) by using several of the SPERT III tests. The work here used the SPERT III E-core configuration tests in which the RIA was initiated by ejecting a control rod. The resulting super-prompt reactivity excursion and negative reactivity feedback produced the familiar bell shaped power increase and decrease. The energy deposition during such a power peak has important safety consequences and provides validation basis for core coupled multi-physics codes. The transients of five separate tests are used to benchmark the PARCS/TRACE coupled code. The models were thoroughly validated using the original experiment documentation. (authors)

Microcapillary blood sampling for serological examinations by radioimmunoassay (RIA) and enzyme immunoassay (ELISA)

Energy Technology Data Exchange (ETDEWEB)

Rodak, L; Smid, B; Valicek, L; Jurak, E [Vyzkumny Ustav Veterinarniho Lekarstvi, Brno-Medlanky (Czechoslovakia)

1984-01-01

Methods were tested of sampling blood and blood serum for serological examinations on filtration paper and into heparinized glass capillaries with transfer into the dilution solution of the given composition. Samples were also examined for ACH virus antibodies. The suitability of the sampling was verified by an examination of samples using ELISA and RIA methods. The results showed the suitability of sampling using microcapillaries. The titres of virus antibodies found using the ELISA and RIA methods were identical and the sensitivity of antibody detection was not reduced even after the sample had been stored for 60 days at a temperature of 20 degC.

Microcapillary blood sampling for serological examinations by radioimmunoassay (RIA) and enzyme immunoassay (ELISA)

International Nuclear Information System (INIS)

Rodak, L.; Smid, B.; Valicek, L.; Jurak, E.

1984-01-01

Methods were tested of sampling blood and blood serum for serological examinations on filtration paper and into heparinized glass capillaries with transfer into the dilution solution of the given composition. Samples were also examined for ACH virus antibodies. The suitability of the sampling was verified by an examination of samples usiOg ELISA and RIA methods. The results showed the suitability of sampling using microcapillaries. The titres of virus antibodies found using the ELISA and RIA methods were identical and the sensitivity of antibody detection was not reduced even after the sample had been stored for 60 days at a temperature of 20 degC. (B.S.)

Simulation and Test of a Fuel Cell Hybrid Golf Cart

Directory of Open Access Journals (Sweden)

Jingming Liang

2014-01-01

Full Text Available This paper establishes the simulation model of fuel cell hybrid golf cart (FCHGC, which applies the non-GUI mode of the Advanced Vehicle Simulator (ADVISOR and the genetic algorithm (GA to optimize it. Simulation of the objective function is composed of fuel consumption and vehicle dynamic performance; the variables are the fuel cell stack power sizes and the battery numbers. By means of simulation, the optimal parameters of vehicle power unit, fuel cell stack, and battery pack are worked out. On this basis, GUI mode of ADVISOR is used to select the rated power of vehicle motor. In line with simulation parameters, an electrical golf cart is refitted by adding a 2 kW hydrogen air proton exchange membrane fuel cell (PEMFC stack system and test the FCHGC. The result shows that the simulation data is effective but it needs improving compared with that of the real cart test.

Development of training simulator based on critical assemblies test bench

International Nuclear Information System (INIS)

Narozhnyi, A.T.; Vorontsov, S.V.; Golubeva, O.A.; Dyudyaev, A.M.; Il'in, V.I.; Kuvshinov, M.I.; Panin, A.V.; Peshekhonov, D.P.

2007-01-01

When preparing critical mass experiment, multiplying system (MS) parts are assembled manually. This work is connected with maximum professional risk to personnel. Personnel training and keeping the skill of working experts is the important factor of nuclear safety maintenance. For this purpose authors develop a training simulator based on functioning critical assemblies test bench (CATB), allowing simulation of the MS assemblage using training mockups made of inert materials. The control program traces the current status of MS under simulation. A change in the assembly neutron physical parameters is mapped in readings of the regular devices. The simulator information support is provided by the computer database on physical characteristics of typical MS components The work in the training mode ensures complete simulation of real MS assemblage on the critical test bench. It makes it possible to elaborate the procedures related to CATB operation in a standard mode safely and effectively and simulate possible abnormal situations. (author)

Distúrbio específico de linguagem: desempenho em testes de memória de trabalho fonológica e de habilidades auditivas

Directory of Open Access Journals (Sweden)

Lidiane Yumi Sawasaki

2017-01-01

Full Text Available Hipóteses vêm sendo apontadas para explicar as dificuldades linguísticas de crianças com Distúrbio Específico de Linguagem (DEL, e, dentre elas, podemos citar alterações na memória de trabalho fonológica (MTF e no processamento auditivo temporal (PAT. Assim, o objetivo do presente estudo foi verificar o desempenho de sujeitos com DEL em testes de MTF, de PAT e de atenção auditiva sustentada (AAS e, ainda, verificar se há correlação entre eles. Foram selecionadas 12 crianças com idades entre 6 e 10 anos, sendo nove meninos, com diagnóstico de DEL da Clínica de Fonoaudiologia da FOBjUSP de Bauru. Foram aplicados os seguintes testes: prova de memória de trabalho fonológica (MTF não palavras e dígitos, teste da habilidade de resolução temporallZl Random Gap Detection Test (RGDT !li e teste de habilidade de atenção auditiva sustentada (THAAS. Nas três provas aplicadas IZIMTF, AAS e PAT !li foram encontrados resultados inferiores à normalidade. Na literatura há fortes evidências de que crianças com DEL apresentam desempenho inadequado em tarefas de MTF que envolvem o armazenamento de um estímulo verbal, fato também confirmado neste trabalho. Como se verificou neste trabalho, DEL pode também estar associado a dificuldades no processamento de elementos acústicos breves e na atenção sustentada. Foi possível verificar com este estudo que quadros de DEL podem apresentar dificuldades de MTF, de atenção sustentada e em habilidades de resolução temporal. Mesmo não havendo correlação entre os testes, a grande maioria das crianças com DEL apresentou desempenho deficitário nas habilidades testadas. O DEL decorre de uma dificuldade constitucional para o processamento neuropsicológico da linguagem, e, desse modo, pessoas com esse quadro podem apresentar disfunção em qualquer nível do processamento, incluindo o processamento auditivo.  

Principles of RIA data management

International Nuclear Information System (INIS)

Chase, G.D.

1983-01-01

The ultimate objective of an RIA is to correlate observed values of radioactivity with observed clinical manifestations that may indicate the existence of a particular disease or metabolic malfunction. To achieve this objective, a two-step process may be considered. First, it is necessary to measure the concentration of a particular chemical entity, the analyte, in the sample presented for analysis. In most cases the analyte is a drug, hormone, or vitamin, or another well-defined chemical substance of known structure and molecular weight. The principal responsibility for measuring the analyte concentration rests with the clinical chemist performing the assay. Second, it is necessary to interpret the assay results in the light of patient history and clinical observations. The principal responsibility for this step lies with the clinician. In this paper, only the first step, the RIA, is considered. Although RIAs in particular are discussed, many of the topics considered apply equally well to radioassays in which the specific binder is not an antibody and to immunoassays in which the tag is not a radioisotope

O "Programa Alfabetização Solidária": terceirização no contexto da reforma do Estado "Programa Alfabetização Solidária" literacy program and State reform in Brazil

Directory of Open Access Journals (Sweden)

Gladys Beatriz Barreyro

2010-12-01

Full Text Available O presente trabalho busca analisar o Programa Alfabetização Solidária a partir de um modelo de Estado proposto pelo governo do presidente Fernando Henrique Cardoso (1997-2002. Considera-se que a proposta de Reforma do Estado ali desenvolvida, a partir do conceito de publicização, teve sua derivação na área social-assistencial do governo na Comunidade Solidária, um ensaio de terceirização na área das políticas sociais. O Alfabetização Solidária, subprograma deste, foi a versão para a área de educação. De modo que algumas características desse Programa específico devem ser discutidas e contextualizadas à luz de um marco mais amplo, analisando conceitos como terceirização, filantropia, empregabilidade temporária, participação social e direito à educação.This article analyses the "Programa de Afabetização Solidária" Literacy Program as a product of the model of State proposed during the two presidential terms of Fernando Henrique Cardoso (1997-2002, in Brazil. I analysed the proposal of State Reform based on publicization and its counterpart in the social-assistance area of the government: the creation of the Solidarity Community ("Comunidade Solidária". This was a test of outsourcing in the social policy area and the "Programa de Afabetização Solidária"Solidarity in Literacy Program, which arose as a subproject of that one, was a laboratory that developed that State model in the educational area. For this reason, some characteristics of this Program are discussed within that frame and concepts like outsourcing, philanthropy, use of cheap and temporary labor force, participation and right to education are analyzed.

The Center-TRACON Automation System: Simulation and field testing

Science.gov (United States)

Denery, Dallas G.; Erzberger, Heinz

1995-01-01

A new concept for air traffic management in the terminal area, implemented as the Center-TRACON Automation System, has been under development at NASA Ames in a cooperative program with the FAA since 1991. The development has been strongly influenced by concurrent simulation and field site evaluations. The role of simulation and field activities in the development process will be discussed. Results of recent simulation and field tests will be presented.

Development of Research Reactor Simulator and Its Application to Dynamic Test-bed

International Nuclear Information System (INIS)

Kwon, Kee Choon; Park, Jae Chang; Lee, Seung Wook; Bang, Dane; Bae, Sung Won

2014-01-01

We developed HANARO and the Jordan Research and Training Reactor (JRTR) real-time simulator for operating staff training. The main purpose of this simulator is operator training, but we modified this simulator as a dynamic test-bed to test the reactor regulating system in HANARO or JRTR before installation. The simulator configuration is divided into hardware and software. The simulator hardware consists of a host computer, 6 operator stations, a network switch, and a large display panel. The simulator software is divided into three major parts: a mathematical modeling module, which executes the plant dynamic modeling program in real-time, an instructor station module that manages user instructions, and a human machine interface (HMI) module. The developed research reactors are installed in the Korea Atomic Energy Research Institute nuclear training center for reactor operator training. To use the simulator as a dynamic test-bed, the reactor regulating system modeling software of the simulator was replaced by a hardware controller and the simulator and target controller were interfaced with a hard-wired and network-based interface

Development of Research Reactor Simulator and Its Application to Dynamic Test-bed

Energy Technology Data Exchange (ETDEWEB)

Kwon, Kee Choon; Park, Jae Chang; Lee, Seung Wook; Bang, Dane; Bae, Sung Won [KAERI, Daejeon (Korea, Republic of)

2014-08-15

We developed HANARO and the Jordan Research and Training Reactor (JRTR) real-time simulator for operating staff training. The main purpose of this simulator is operator training, but we modified this simulator as a dynamic test-bed to test the reactor regulating system in HANARO or JRTR before installation. The simulator configuration is divided into hardware and software. The simulator hardware consists of a host computer, 6 operator stations, a network switch, and a large display panel. The simulator software is divided into three major parts: a mathematical modeling module, which executes the plant dynamic modeling program in real-time, an instructor station module that manages user instructions, and a human machine interface (HMI) module. The developed research reactors are installed in the Korea Atomic Energy Research Institute nuclear training center for reactor operator training. To use the simulator as a dynamic test-bed, the reactor regulating system modeling software of the simulator was replaced by a hardware controller and the simulator and target controller were interfaced with a hard-wired and network-based interface.

Testing power system controllers by real-time simulation

DEFF Research Database (Denmark)

Venne, Philippe; Guillaud, Xavier; Sirois, Frédéric

2007-01-01

In this paper, we present a number of state-of-the art methods for testing power system controllers based on the use of a real-time power system simulator. After introducing Hypersim, we list and discuss the different means of connection between the controller under tests and the power system...

Revascularização da artéria coronária direita intra-atrial Revascularization of intracavitary right coronary artery

Directory of Open Access Journals (Sweden)

Artur Lourenção Júnior

1990-12-01

Full Text Available A artéria coronária direita, em seu trajeto no sulco atrioventricular direito, pode, em raras ocasiões, penetrar na cavidade atrial direita. Esta variação anatômica poderá modificar a tática cirúrgica em operações de revascularização miocárdica. No presente trabalho, relatamos o caso em que a ponte de veia safena para a artéria coronária direita foi realizada em posição intra-atrial direita.The right coronary artery, during your course in the right atrioventricular sulcus, can sometimes penetrate the right atrial cavity. This anatomical variety can modify the surgical tactics in aortocoronary by-pass surgery. In this paper we present a patient in whom the by-pass with saphenous vein graft to the right coronary artery was made in right intracavitary position.

Comparative Performance of Four Single Extreme Outlier Discordancy Tests from Monte Carlo Simulations

Directory of Open Access Journals (Sweden)

Surendra P. Verma

2014-01-01

Full Text Available Using highly precise and accurate Monte Carlo simulations of 20,000,000 replications and 102 independent simulation experiments with extremely low simulation errors and total uncertainties, we evaluated the performance of four single outlier discordancy tests (Grubbs test N2, Dixon test N8, skewness test N14, and kurtosis test N15 for normal samples of sizes 5 to 20. Statistical contaminations of a single observation resulting from parameters called δ from ±0.1 up to ±20 for modeling the slippage of central tendency or ε from ±1.1 up to ±200 for slippage of dispersion, as well as no contamination (δ=0 and ε=±1, were simulated. Because of the use of precise and accurate random and normally distributed simulated data, very large replications, and a large number of independent experiments, this paper presents a novel approach for precise and accurate estimations of power functions of four popular discordancy tests and, therefore, should not be considered as a simple simulation exercise unrelated to probability and statistics. From both criteria of the Power of Test proposed by Hayes and Kinsella and the Test Performance Criterion of Barnett and Lewis, Dixon test N8 performs less well than the other three tests. The overall performance of these four tests could be summarized as N2≅N15>N14>N8.

Standard Practice for Solar Simulation for Thermal Balance Testing of Spacecraft

CERN Document Server

American Society for Testing and Materials. Philadelphia

1973-01-01

1.1 Purpose: 1.1.1 The primary purpose of this practice is to provide guidance for making adequate thermal balance tests of spacecraft and components where solar simulation has been determined to be the applicable method. Careful adherence to this practice should ensure the adequate simulation of the radiation environment of space for thermal tests of space vehicles. 1.1.2 A corollary purpose is to provide the proper test environment for systems-integration tests of space vehicles. An accurate space-simulation test for thermal balance generally will provide a good environment for operating all electrical and mechanical systems in their various mission modes to determine interferences within the complete system. Although adherence to this practice will provide the correct thermal environment for this type of test, there is no discussion of the extensive electronic equipment and procedures required to support systems-integration testing. 1.2 Nonapplicability—This practice does not apply to or provide inco...

Retran simulation of Oyster Creek generator trip startup test

International Nuclear Information System (INIS)

Alammar, M.A.

1987-01-01

RETRAN simulation of Oyster Creek generator trip startup test was carried out as part of Oyster Creek RETRAN model qualification program for reload licensing applications. The objective of the simulation was to qualify the turbine model and its interface with the control valve and bypass systems under severe transients. The test was carried out by opening the main breakers at rated power. The turbine speed governor closed the control valves and the pressure regulator opened the bypass valves within 0.5 sec. The stop valves closed by a no-load turbine trip, before the 10 percent overspeed trip was reached and the reactor scrammed on high APRM neutron flux. The simulation resulted in qualifying a normalized hydraulic torque for the turbine model and a 0.3 sec, delay block for the bypass model to account for the different delays in the hydraulic linkages present in the system. One-dimensional kinetics was used in this simulation

História, estórias e memórias mineiras em Guimarães Rosa

Directory of Open Access Journals (Sweden)

Francis Paulina Lopes da Silva

2005-10-01

Full Text Available Leitura de aspectos da cultura popular, presentes no processo de construção ficcional  de Guimarães  Rosa, o “contista de contos críticos”, que confessara: "Não preciso  in venta r contos,  eles vêm até  mim”. Pela alquimia da palavra e m seu estado primitivo, a fusão do  real e ficcional com o obsessiva defesa de que "a legítima literatura  deve servida". A multiplicação do imaginário rural mineiro n a narrativa rosiana, especificamente, em contos de Tutaméia e Ave, Palavra. Historia e estória n o cotidiano do  povo  do sertão  mineiro. Pelo  jogo da memória narrativa popular, a construção da identidade cultural sertaneja e a recriação do mito: "No sertão, o homem é o eu que ainda não encontrou o tu:  por isso ali os anjos ou o diabo ainda  manuseiam a língua".

Um Passado Jogável? Simulação Digital, Videogames e História Pública

Directory of Open Access Journals (Sweden)

Helyom Viana Telles

2016-05-01

Full Text Available O presente trabalho foi originado a partir das reflexões suscitadas por uma pesquisa de pós-doutorado que investiga como os jogos eletrônicos podem contribuir para a produção e o compartilhamento de representações, de imagens e de um imaginário sobre o passado, atuando como suporte para a memória coletiva. O artigo propõe uma reflexão sobre as relações entre simulação digital, o conhecimento do passado e a história pública com base na discussão da produção bibliográfica recente de historiadores norte-americanos que tratam do tema. O artigo critica a dicotomia entre jogos digitais educativos comerciais conclui que os elementos ficcionais presentes em simulações e jogos digitais oferecem a oportunidade para o exercício de exploração da história contrafatual. Essa característica, aliada à possibilidade de expressão de dados e conhecimentos históricos complexos, tornam as simulações e jogos digitais valiosas para o campo da história pública. Palavras-Chave: História Pública, Simulação Digital, Videogame ABSTRACT This study  originated from the thinking generated by a post-doctoral research that investigates how computer games can contribute to the production and representations sharing, pictures and an imaginary about the past, acting as support for the memory collective. The article proposes a study of the links between digital simulation, knowledge of the past history and the public based on the discussion of recent literature production of American historians on the same matter. The article criticizes the dichotomy between commercial educational digital games concludes that the fictional elements present in simulations and digital games offer the opportunity to exercise exploitation of counterfactual history. This feature, combined with the possibility of data expression and complex historical knowledge, make the simulations and valuable digital games to the field of public history. Keywords: Public history

Perfis Diferenciais de Perda de Memória entre a Demência Frontotemporal e a do Tipo Alzheimer

Directory of Open Access Journals (Sweden)

Allegri Ricardo F.

2001-01-01

Full Text Available Os estados iniciais da demência tipo Alzheimer (DTA caracterizam-se classicamente por deterioração da memória enquanto que as mudanças de conduta e de personalidade aparecem nas etapas iniciais da demência frontotemporal (DFT. Entretanto, na prática clínica, o diagnóstico diferencial é difícil. O objetivo do presente trabalho foi estudar o rendimento da memória de pacientes com DTA (n= 20 e com DFT (n= 20 comparando-o com um grupo de controles (n = 20. Os pacientes, emparelhados por idade e escolaridade, foram avaliados com uma bateria neuropsicológica exaustiva. Para a avaliação da memória, examinou-se a "queixa subjetiva" de perda de memória (memória subjetiva, a aprendizagem de uma lista de palavras (memória episódica e o desempenho no teste de denominação de Boston (memória semântica. As pontuações de ambos os grupos de pacientes, na grande maioria das provas, foram significativamente inferiores às dos controles. Os pacientes com DTA mostraram uma deterioração global da memória episódica (tipo amnésia e semântica com um alto nível de queixa subjetiva. Os sujeitos com DFT, por outro lado, apresentaram um déficit de memória importante na recuperação da informação, mas com melhores capacidades de registro da informação, apesar das dificuldades de reconhecimento do seu distúrbio.

Cutis verticis gyrata primária essencial

Directory of Open Access Journals (Sweden)

Schenato Letícia K.

2002-01-01

Full Text Available Objetivo: relatar um caso raro de uma criança portadora da forma primária essencial de Cutis verticis gyrata.Descrição: menino de 9 anos, apresenta importante hipertrofia da pele do couro cabeludo, com dobras que se assemelham aos giros cerebrais. Não apresenta retardo mental, nem alterações oftalmológicas e não há relatos semelhantes na família.Comentários: o diagnóstico de Cutis verticis gyrata primária essencial foi estabelecido pela presença de redundância da pele do couro cabeludo e ausência de alterações neurológicas e oftalmológicas, tendo-se feito o diagnóstico diferencial com as formas secundárias que incluem: nevo intradérmico cerebriforme, paquidermoperiostose, acromegalia e doenças inflamatórias do couro cabeludo. Trata-se do único relato na literatura de uma criança com esta forma de Cutis verticis gyrata.

Resonant Column Tests and Nonlinear Elasticity in Simulated Rocks

Science.gov (United States)

Sebastian, Resmi; Sitharam, T. G.

2018-01-01

Rocks are generally regarded as linearly elastic even though the manifestations of nonlinearity are prominent. The variations of elastic constants with varying strain levels and stress conditions, disagreement between static and dynamic moduli, etc., are some of the examples of nonlinear elasticity in rocks. The grain-to-grain contact, presence of pores and joints along with other compliant features induce the nonlinear behavior in rocks. The nonlinear elastic behavior of rocks is demonstrated through resonant column tests and numerical simulations in this paper. Resonant column tests on intact and jointed gypsum samples across varying strain levels have been performed in laboratory and using numerical simulations. The paper shows the application of resonant column apparatus to obtain the wave velocities of stiff samples at various strain levels under long wavelength condition, after performing checks and incorporating corrections to the obtained resonant frequencies. The numerical simulation and validation of the resonant column tests using distinct element method are presented. The stiffness reductions of testing samples under torsional and flexural vibrations with increasing strain levels have been analyzed. The nonlinear elastic behavior of rocks is reflected in the results, which is enhanced by the presence of joints. The significance of joint orientation and influence of joint spacing during wave propagation have also been assessed and presented using the numerical simulations. It has been found that rock joints also exhibit nonlinear behavior within the elastic limit.

Memória fonológica em crianças bilíngues bimodais e crianças com implante coclear

Science.gov (United States)

de Quadros, Ronice Müller; Cruz, Carina Rebello; Pizzio, Aline Lemos

2014-01-01

RESUMO Este estudo comparou o desempenho de crianças bilíngues bimodais ouvintes (filhas de pais surdos) e crianças surdas usuárias de implante coclear (filhas de pais surdos e de pais ouvintes), com diferentes contextos de acesso à Língua Brasileira de Sinais (Libras), em tarefas que envolvem memória fonologica. Os testes utilizados foram: Teste de Pseudopalavras (Santos e Bueno, 2003) e Teste de Pseudosinais (desenvolvido pelos pesquisadores responsáveis pelo Projeto ‘Desenvolvimento Bilíngue Bimoda’). Além disso, foram incluídos dois grupos de controle, formados por crianças surdas (usuarias de Libras), e adultos bilíngues bimodais ouvintes. Na análise dos resultados, em relação ao desempenho entre os dois grupos testados foi constatado que o grupo de crianças bilíngues bimodais ouvintes apresentou desempenho superior, nos dois testes. No entanto, ao ser analisado o desempenho da criança surda usuaria de implante coclear, filha de pais surdos, que possui acesso irrestrito à Libras e comparado com o das crianças surdas usuárias de implante coclear, que possuem acesso restrito à Libras, foi constatado que o seu desempenho foi semelhante ao do grupo de crianças bilíngues bimodais ouvintes. As crianças surdas usuárias de implante coclear com acesso restrito à Libras e, portanto, com acesso maior ao Português apresentaram escores mais baixos nas tarefas, principalmente do teste em Português. Os resultados sugerem que as crianças surdas usuárias de implante coclear em processo de aquisição da línguagem podem se beneficiar com o acesso irrestrito à Libras, atingindo inclusive desempenho semelhante a de crianças bilíngues bimodais ouvintes. PMID:25110473

Test system to simulate transient overpower LMFBR cladding failure

International Nuclear Information System (INIS)

Barrus, H.G.; Feigenbutz, L.V.

1981-01-01

One of the HEDL programs has the objective to experimentally characterize fuel pin cladding failure due to cladding rupture or ripping. A new test system has been developed which simulates a transient mechanically-loaded fuel pin failure. In this new system the mechanical load is prototypic of a fuel pellet rapidly expanding against the cladding due to various causes such as fuel thermal expansion, fuel melting, and fuel swelling. This new test system is called the Fuel Cladding Mechanical Interaction Mandrel Loading Test (FCMI/MLT). The FCMI/MLT test system and the method used to rupture cladding specimens very rapidly to simulate a transient event are described. Also described is the automatic data acquisition and control system which is required to control the startup, operation and shutdown of the very fast tests, and needed to acquire and store large quantities of data in a short time

Estórias e história: memórias de telespectadores sobre novelas de 1970 e 1980 = Stories and history: TV viewers’ memories about 70s and 80s soap operas

Directory of Open Access Journals (Sweden)

Gonçales, Diego Franco

2015-01-01

Full Text Available Este artigo apresenta um estudo sobre as relações entre memórias, imaginário e telenovelas. Utilizando depoimentos de telespectadores da região do Grande ABC (estado de São Paulo, colhidos por meio da metodologia da História Oral, articula memórias individuais sobre as telenovelas e o contexto sociopolítico das décadas de 1970 e 1980. Como resultado, apresenta a percepção de um gradual despertar dos entrevistados para a complexidade da relação TV-sociedade, e também a ação de uma visão retroativa sobre a qualidade das telenovelas (as novelas atuais precipitando uma visão de que as novelas anteriores eram melhores. Por fm, aponta para a fecundidade desse caminho metodológico: o estudo das memórias como uma ferramenta para a compreensão da infuência da telenovela sobre o imaginário social

A Fault Sample Simulation Approach for Virtual Testability Demonstration Test

Institute of Scientific and Technical Information of China (English)

ZHANG Yong; QIU Jing; LIU Guanjun; YANG Peng

2012-01-01

Virtual testability demonstration test has many advantages,such as low cost,high efficiency,low risk and few restrictions.It brings new requirements to the fault sample generation.A fault sample simulation approach for virtual testability demonstration test based on stochastic process theory is proposed.First,the similarities and differences of fault sample generation between physical testability demonstration test and virtual testability demonstration test are discussed.Second,it is pointed out that the fault occurrence process subject to perfect repair is renewal process.Third,the interarrival time distribution function of the next fault event is given.Steps and flowcharts of fault sample generation are introduced.The number of faults and their occurrence time are obtained by statistical simulation.Finally,experiments are carried out on a stable tracking platform.Because a variety of types of life distributions and maintenance modes are considered and some assumptions are removed,the sample size and structure of fault sample simulation results are more similar to the actual results and more reasonable.The proposed method can effectively guide the fault injection in virtual testability demonstration test.

Development of research reactor simulator and its application to dynamic test-bed

International Nuclear Information System (INIS)

Kwon, Kee-Choon; Baang, Dane; Park, Jae-Chang; Lee, Seung-Wook; Bae, Sung Won

2014-01-01

We developed a real-time simulator for 'High-flux Advanced Neutron Application ReactOr (HANARO), and the Jordan Research and Training Reactor (JRTR). The main purpose of this simulator is operator training, but we modified this simulator into a dynamic test-bed (DTB) to test the functions and dynamic control performance of reactor regulating system (RRS) in HANARO or JRTR before installation. The simulator hardware consists of a host computer, 6 operator stations, a network switch, and a large display panel. The software includes a mathematical model that implements plant dynamics in real-time, an instructor station module that manages user instructions, and a human machine interface module. The developed research reactor simulators are installed in the Korea Atomic Energy Research Institute nuclear training center for reactor operator training. To use the simulator as a dynamic test-bed, the reactor regulating system modeling software of the simulator was replaced by actual RRS cabinet, and was interfaced using a hard-wired and network-based interface. RRS cabinet generates control signals for reactor power control based on the various feedback signals from DTB, and the DTB runs plant dynamics based on the RRS control signals. Thus the Hardware-In-the-Loop Simulation between RRS and the emulated plant (DTB) has been implemented and tested in this configuration. The test result shows that the developed DTB and actual RRS cabinet works together simultaneously resulting in quite good dynamic control performances. (author)

Matéria atrai matéria... e a antimatéria?

OpenAIRE

Chalub, Fabio Augusto da Costa Carvalho

2016-01-01

A lei da Gravidade de Newton afirma que duas partículas se atraem, sobre a linha que as une, com uma força proporcional ao produto das massas e inversamente proporcional ao quadrado da distância. Mas o que aconteceria se tivéssemos partículas de massa negativa? Será possível que tenhamos por aí partículas que se repelem? Será a antimatéria uma candidata a sentir a força antigravitacional? Uma nova pesquisa lança luz nestes antigos mistérios. publishersversion published

Produção de matéria seca da braquiária de acordo com os atributos químicos de um Latossolo em Selvíria, Mato Grosso do Sul

Directory of Open Access Journals (Sweden)

Rafael Montanari

2013-08-01

Full Text Available Forrageiras rústicas, como as braquiárias, são predominantes na região do Cerrado, no sistema de pecuária extensiva, que favorece a degradação do solo. Entretanto, com o tempo, nem mesmo essas forrageiras conseguem bom desenvolvimento nessas áreas. O objetivo deste trabalho foi analisar a variabilidade dos atributos estudados da planta e do solo; definir as correlações lineares e espaciais entre a produtividade do capim-braquiária com os atributos químicos do solo pesquisado, e pesquisar, dentre os atributos químicos do solo, aquele que melhor se apresente para explicar a variabilidade da produtividade dessa forrageira. A pesquisa foi desenvolvida em uma área manejada com pastagem há 30 anos, na Fazenda de Ensino, Pesquisa e Extensão (FEPE da Faculdade de Engenharia de Ilha Solteira - UNESP, em Selvíria - MS. Foi instalada a malha geoestatística num Latossolo Vermelho aluminoférrico, para a coleta de dados do solo e da planta, contendo 121 pontos amostrais, constituídos de 11 transeções, com 160 m de largura, na direção dos eixos cartesianos. A produção de massa de matéria seca de capim-braquiária foi baixa, apresentando alta variação. Os atributos MSr, N, PB, MO1, MO2, pHa1, pHa2, pHk1 e pHk2 não variaram aleatoriamente e apresentaram variabilidade dos dados entre baixa e alta, e seguiram padrões espaciais bem definidos, com alcances entre 17,7 e 162,9 m. Houve correlação linear significativa a 1% entre a MSr e o N, e entre MSr e a PB. A existência dos semivariogramas cruzados MSr=f(N e MSr=f(PB atestou que essa matéria seca pode ser estimada a partir dos dados do teor de nitrogênio foliar e proteína bruta dessa forrageira.

EM BUSCA DA HISTORICIDADE DO MUNICÍPIO DE QUEIMADOS: EXPERIÊNCIAS POSSÍVEIS ENTRE A HISTÓRIA PÚBLICA E O ENSINO DE HISTÓRIA

Directory of Open Access Journals (Sweden)

Claudia Patrícia de Oliveira Costa Correio

2015-07-01

Full Text Available Claudia Patrícia de Oliveira Costa Correio DOI: 10.12957/periferia.2014.17236Durante as entrevistas realizadas junto à população queimadense entre os anos de 2009 e 2013, identificamos significativo desconforto revelado diante do desenvolvimento da cidade. Tal desconforto expressou-se, na fala dos entrevistados, a partir do crescente interesse dos depoentes em compartilhar suas memórias, registrando-as como "uma resposta ou reação, diante das mudanças rápidas e de uma vida sem âncoras ou raízes" (JELIN, 2002, p. 9. Nesse sentido, constatamos que a preocupação de muitos queimadenses, especialmente aqueles cujas trajetórias de vida se caracterizaram pela maior atuação na esfera pública, introduz questões como a importância das memórias para a escrita e o ensino de História, sua divulgação, a patrimonialização cultural e a dívida do presente com o passado.Palavras-chave: Ensino de História; história pública; memória; Queimados

A memória de Borges

Directory of Open Access Journals (Sweden)

Eneida Maria Souza

2010-08-01

nefasta ou de outra ordem? Sem atribuir algum juízo de valor ao debate, pretende-se apontar um dos pontos da poética borgiana responsável por sua consagração mundial, qual seja, o da autonomia literária. A presença/ausência da imagem do escritor/autor transforma-se em tema literário, intriga que se enreda/desenreda como espelho reduplicador da vida literária e da literatura.

The relationship between working memory and apraxia of speech A interrelação entre memória operacional e apraxia de fala

Directory of Open Access Journals (Sweden)

Fernanda Chapchap Martins

2009-09-01

Full Text Available The present study aimed to verify the relationship between working memory (WM and apraxia of speech and explored which WM components were involved in the motor planning of speech. A total of 22 patients and 22 healthy adults were studied. These patients were selected according to the following inclusion criteria: a single brain lesion in the left hemisphere, presence of apraxia of speech and sufficient oral comprehension. This study involved assessment of apraxia of speech and evaluation of working memory capacity. The performance of apraxic patients was significantly poorer than that of controls, where this reached statistical significance. The study concluded that participants with apraxia of speech presented a working memory deficit and that this was probably related to the articulatory process of the phonoarticulatory loop. Furthermore, all apraxic patients presented a compromise in working memory.O objetivo do presente estudo foi verificar a interrelação entre memória operacional e apraxia verbal e explorar quais os componentes desta memória estariam envolvidos na programação motora da fala. Foram avaliados 22 pacientes apráxicos e 22 controles. Todos os participantes foram submetidos a avaliação da apraxia de fala. Para investigar a memória operacional, foram aplicados o teste de span de dígitos na ordem direta e inversa, um teste de repetição de palavras longas e curtas e o Rey Auditory Verbal Learning Test, que investiga, além da alça articulatória, o buffer episódico. O desempenho dos apráxicos em todos os testes de memória foi estatisticamente significante mais baixo que o desempenho dos controles. Concluímos que indivíduos com apraxia apresentam um déficit na memória operacional e que este déficit está mais relacionado ao processo articulatório da alça fonoarticulatória.

Irradiation test plan of the simulated DUPIC fuel

Energy Technology Data Exchange (ETDEWEB)

Bae, Ki Kwang; Yang, M. S.; Kim, B. K. [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-11-01

Simulated DUPIC fuel had been irradiated from Aug. 4, 1999 to Oct. 4 1999, in order to produce the data of its in-core behavior, to verify the design of DUPIC non-instrumented capsule developed, and to ensure the irradiation requirements of DUPIC fuel at HANARO. The welding process was certified for manufacturing the mini-element, and simulated DUPIC fuel rods were manufactured with simulated DUPIC pellets through examination and test. The non-instrumented capsule for a irradiation test of DUPIC fuel has been designed and manufactured referring to the design specification of the HANARO fuel. This is to be the design basis of the instrumented capsule under consideration. The verification experiment, whether the capsule loaded in the OR4 hole meet the HANARO requirements under the normal operation condition, as well as the structural analysis was carried out. The items for this experiment were the pressure drop test, vibration test, integrity test, et. al. It was noted that each experimental result meet the HANARO operational requirements. For the safety analysis of the DUPIC non-instrumented capsule loaded in the HANARO core, the nuclear/mechanical compatibility, thermodynamic compatibility, integrity analysis of the irradiation samples according to the reactor condition as well as the safety analysis of the HANARO were performed. Besides, the core reactivity effects were discussed during the irradiation test of the DUPIC capsule. The average power of each fuel rod in the DUPIC capsule was calculated, and maximal linear power reflecting the axial peaking power factor from the MCNP results was evaluated. From these calculation results, the HANARO core safety was evaluated. At the end of this report, similar overseas cases were introduced. 9 refs., 16 figs., 10 tabs. (Author)

História, memória e derrisão em Narradores de Javé

OpenAIRE

Côrtes, Norma

2010-01-01

A História e o passado têm sido objetos de humor na cultura brasileira. Tradicionalmente, os fatos históricos foram temas oficiais obrigatórios para os sambas enredos no carnaval carioca.  Os heróis e as glórias do passado que fomentariam os mais sérios sentimentos cívicos foram cantados e ensinados em versos carnavalescos que, irreverentemente, misturavam heroísmo com comicidade. O ápice crítico dessa derrisão apareceu em o Samba do Crioulo Doido — música de Stanislaw Ponte Preta (Sérgio Por...

A Monte Carlo Simulation Framework for Testing Cosmological Models

Directory of Open Access Journals (Sweden)

Heymann Y.

2014-10-01

Full Text Available We tested alternative cosmologies using Monte Carlo simulations based on the sam- pling method of the zCosmos galactic survey. The survey encompasses a collection of observable galaxies with respective redshifts that have been obtained for a given spec- troscopic area of the sky. Using a cosmological model, we can convert the redshifts into light-travel times and, by slicing the survey into small redshift buckets, compute a curve of galactic density over time. Because foreground galaxies obstruct the images of more distant galaxies, we simulated the theoretical galactic density curve using an average galactic radius. By comparing the galactic density curves of the simulations with that of the survey, we could assess the cosmologies. We applied the test to the expanding-universe cosmology of de Sitter and to a dichotomous cosmology.

Urticária Urticaria

Directory of Open Access Journals (Sweden)

Paulo Ricardo Criado

2005-12-01

Full Text Available A urticária apresenta-se com diversas formas clínicas e causas distintas. Constitui uma das dermatoses mais freqüentes: 15% a 20% da população têm pelo menos um episódio agudo da doença em sua vida, resultando em percentual que varia de um a 2% dos atendimentos nas especialidades de Dermatologia e Alergologia. A urticária é classificada do ponto de vista de duração da evolução temporal em aguda (inferior a seis semanas ou crônica (superior a seis semanas. O tratamento da urticária pode compreender medidas não farmacológicas e intervenções medicamentosas, as quais são agrupadas em tratamentos de primeira (anti-histamínicos, segunda (corticosteróides e antileucotrienos e terceira linha (medicamentos imunomoduladores. As medidas terapêuticas de segunda e terceira linha apresentam maiores efeitos adversos, devendo ser reservadas aos doentes que não apresentaram controle da doença com os de primeira linha, ou àqueles a respeito dos quais não é possível estabelecer uma etiologia, tal como nas urticárias auto-imunes.Urticaria has diverse clinical presentations and causes. It is one of the most frequent dermatological conditions: 15% to 20% of population has at least one acute eruption during their lifetime, resulting in 1% to 2% of dermatological and allergological visits. Urticaria is classified based on its temporal evolution as acute (less than 6 weeks or chronic (more than 6 weeks. Management strategies may involve non-pharmacological measures and drug interventions, which are grouped into first- (antihistamines, second- (corticosteroids and anti-leukotrienes and third-line therapies (immunomodulators. Stronger, but potentially riskier, second- and third-line management may be justified for patients who do not respond to first-line therapy, or whenever a specific etiology cannot be determined, such as in autoimmune urticaria.

High Performance Electrical Modeling and Simulation Verification Test Suite - Tier I; TOPICAL

International Nuclear Information System (INIS)

SCHELLS, REGINA L.; BOGDAN, CAROLYN W.; WIX, STEVEN D.

2001-01-01

This document describes the High Performance Electrical Modeling and Simulation (HPEMS) Global Verification Test Suite (VERTS). The VERTS is a regression test suite used for verification of the electrical circuit simulation codes currently being developed by the HPEMS code development team. This document contains descriptions of the Tier I test cases

Flight Testing an Iced Business Jet for Flight Simulation Model Validation

Science.gov (United States)

Ratvasky, Thomas P.; Barnhart, Billy P.; Lee, Sam; Cooper, Jon

2007-01-01

A flight test of a business jet aircraft with various ice accretions was performed to obtain data to validate flight simulation models developed through wind tunnel tests. Three types of ice accretions were tested: pre-activation roughness, runback shapes that form downstream of the thermal wing ice protection system, and a wing ice protection system failure shape. The high fidelity flight simulation models of this business jet aircraft were validated using a software tool called "Overdrive." Through comparisons of flight-extracted aerodynamic forces and moments to simulation-predicted forces and moments, the simulation models were successfully validated. Only minor adjustments in the simulation database were required to obtain adequate match, signifying the process used to develop the simulation models was successful. The simulation models were implemented in the NASA Ice Contamination Effects Flight Training Device (ICEFTD) to enable company pilots to evaluate flight characteristics of the simulation models. By and large, the pilots confirmed good similarities in the flight characteristics when compared to the real airplane. However, pilots noted pitch up tendencies at stall with the flaps extended that were not representative of the airplane and identified some differences in pilot forces. The elevator hinge moment model and implementation of the control forces on the ICEFTD were identified as a driver in the pitch ups and control force issues, and will be an area for future work.

Enhanced operator-training simulator for the Fast Flux Test Facility

International Nuclear Information System (INIS)

Schrader, F.D.; Swanson, C.D.

1983-01-01

The FFTF Plant Operator Training Simulator Facility has proven to be a valuable asset throughtout the testing, startup and early operational phases of the Fast Flux Test facility. However, limitations inherent in the existing simulation facility, increased emphasis on the required quality of operator training, and an expanded scope of applications (e.g., MNI development) justify an enhanced facility. Direct use of plant operators in the development of improved reactor control room displays and other man/machine interface equipment and procedures increases the credibility of proposed techniques and reported results. The FFTF Plant Operator Training Simulator provides a key element in this development program

Development of techniques for joining fuel rod simulators to test assemblies

International Nuclear Information System (INIS)

Moorhead, A.J.; Reed, R.W.

1980-01-01

A unique tubular electrode carrier is described for gas tungsten-arc welding small-diameter nuclear fuel rod simulators to the tubesheet of a test assembly. Both the close-packed geometry of the array of simulators and the extension of coaxial electrical conductors from each simulator hindered access to the weld joint. Consequently, a conventional gas tungsten-arc torch could not be used. Two seven-rod assemblies that were mockups of the simulator-to-tubesheet joint area were welded and successfully tested. Modified versions of the electrode carrier for brazing electrical leads to the upper ends of the fuel pin simulators are also described. Satisfactory brazes have been made on both single-rod mockups and an array of 25 simulators by using the modified electrode carrier and a filler metal with a composition of 71.5 Ag-28 Cu-0.5 Ni

New RIA kit for determination of progesterone in cow milk

International Nuclear Information System (INIS)

Byszewska-Szpocinska, E.; Markiewicz, A.

2006-01-01

The determination of progesterone concentration in whole and fat-free milk 19-24 days after conception enables to distinguish fertile and non-fertile insemination, which is important in cattle breeding. The aim of this work was to develop a simple and quick radioimmunoassay test for the determination of progesterone in cow milk. Two types of solid-phase tubes coated with specific polyclonal anti-progesterone antibody from ORION Diagnostica and BIOSOURCE International, two different progesterone derivatives viz. progesterone-3- carboxymethyl oxime (CMO) and progesterone-11α-hemisuccinate (HS) conjugated to 125 I-histamine and the HPLC system with Lichrospher RP-18 column along with 65% acetonitrile/water as eluent to purify the tracers were used to carry out this work. Progesterone-3CMO- 125 I-histamine had a retention time of 13.2 min and progesterone-11α-hemisuccinate- 125 I-histamine had a retention time of 7.8 min. Two kinds of kits (kit I and kit II) were prepared, first with progesterone-3CMO- 125 I-histamine as the tracer and coated tubes from Progesterone Veterinary RIA kit of ORION Diagnostica and the second with progesterone-11αHS- 125 I-histamine as the tracer and coated tubes from Progesterone Veterinary RIA kit from BIOSOURCE International. Progesterone from Sigma and selected fat-free cow's milk without progesterone as zero progesterone milk matrix were used for standard preparation. The optimal assay procedure was as follows: 50μL standards, controls and fat-free milk samples were pipetted into coated tubes followed by addition of 500μL of diluted tracer. The tubes were incubated for 2h in case of kit I and 3h for kit II at RT. After the incubation, the tubes were decanted and counted. The assay range was 0 to 270 nmol/L for kit I and 0 to 300 nmol/L for kit II. The sensitivity of the kit with ORION coated tubes was better (0.8 nmol/L) than that of BIOSOURCE tubes which was 1.5 nmol/L. Validation of these assays in terms of specificity, accuracy

História dos modos gregos : história da estrutura dos gêneros musicais gregos

OpenAIRE

Lucas Fernandes de Paula

2015-01-01

A pesquisa que se desenvolve sobre a história da música tem por objetivos gerais, compreender, explicar, diversas medidas do objeto de análise: os modos gregos. Especificamente, os objetivos constituem narrativas historiográficas que permitam refletir, no tempo, conteúdos relacionados, e uma história da música perpetrada sob a lente dos chamados modos gregos; pensar o conceito de modos gregos em seu envolvimento com conhecimentos teóricos e práticos em Geografia, Física, Matemática, Filosofia...

Simulation and Analysis of Converging Shock Wave Test Problems

Energy Technology Data Exchange (ETDEWEB)

Ramsey, Scott D. [Los Alamos National Laboratory; Shashkov, Mikhail J. [Los Alamos National Laboratory

2012-06-21

Results and analysis pertaining to the simulation of the Guderley converging shock wave test problem (and associated code verification hydrodynamics test problems involving converging shock waves) in the LANL ASC radiation-hydrodynamics code xRAGE are presented. One-dimensional (1D) spherical and two-dimensional (2D) axi-symmetric geometric setups are utilized and evaluated in this study, as is an instantiation of the xRAGE adaptive mesh refinement capability. For the 2D simulations, a 'Surrogate Guderley' test problem is developed and used to obviate subtleties inherent to the true Guderley solution's initialization on a square grid, while still maintaining a high degree of fidelity to the original problem, and minimally straining the general credibility of associated analysis and conclusions.

A comparison study between RIA and HI procedures for Rubella in a small laboratory practice

International Nuclear Information System (INIS)

Kardos, L.A.

1983-01-01

Two different kits of Rubella Antibody determinations were compared; one, the HI, or Hemoagglutination Inhibition, and the other, an RIA or Radioimmunoassay. Both procedures were quite accurate, adequate, and reproducible, but the RIA procedure was found to be slightly more sensitive than the HI procedure. Two hundred and fifty pregnant women were tested and classified as to origin, background, and race. There was no difference in determination results on those bases. The American Black women had a higher percentage of immunity than the American Anglo-Saxon and European background women. The Latin American patients ranged with the American Black women along with the SE Asian women as far as the percent of immunity was concerned. RIA appears to be more sensitive than HI, especially where a finer delineation is required between immune and non-immune patient results. As far as performance is concerned, the RIA procedure is less complicated and, therefore, less vulnerable to human error. The HI procedure, though quite reproducible and an excellent diagnostic tool, is more time consuming and more involved so the chance for human error in that procedure might be increased

Avaliação da memória de trabalho em crianças com transtorno do déficit de atenção e hiperatividade

Directory of Open Access Journals (Sweden)

Lucinete de Freitas Messina

2009-06-01

Full Text Available Esse projeto investigou as habilidades cognitivas da Memória de Trabalho de crianças e adolescentes com o “Transtorno do Déficit de Atenção e Hiperatividade” (TDAH. Foi aplicado teste TIHC - Teste Infantil de Habilidades Cognitivas informatizado, avaliando principalmente cinco habilidades cognitivas Raciocínio Indutivas (RI, Memória de Armazenamento Auditiva (MAA e Visual e Memória de Trabalho Auditiva (MTA e Visual (MTV usando o modelo de Cattell-Horn-Carroll. O teste foi aplicado em 62 sujeitos sendo 32 com TDAH do Hospital das Clínicas-SEPIA-USP e 30 sujeitos controle “normal” do Ensino Fundamental da rede municipal de 1ª à 8ª séries com idades entre 7 e 15 anos, de ambos os sexos. As análises executadas indicaram a existência de diferenças em diversos aspectos relacionados à memória nos tipos peculiares de crianças com TDAH. Verificou-se que as crianças com TDAH obtiveram bom desempenho nas provas de memória visual em detrimento as provas de memória auditiva. A correlação dos resultados do TIHC verificara que o tempo de reação da prova de memória de armazenamento visual manteve uma correlação significativa com a prova de cálculo.

As normas de competência tributária

OpenAIRE

Follador, Guilherme Broto

2013-01-01

Resumo: O objetivo principal deste trabalho é analisar, criticamente, o conceito de competência tributária e as propostas doutrinárias de formalização das normas de competência tributária, expondo, a partir das lições colhidas sobre o tema, na Teoria Geral do Direito, os principais problemas encontrados nas tentativas de reconstruílas como típicas normas prescritivas. No primeiro capítulo, o estudo é dedicado ao exame das noções de "norma" e de "norma jurídica", e tem por principal finalidade...

Dermatologia veterinária em animais de companhia

OpenAIRE

Pinho, Renato Martins

2015-01-01

Dissertação de Mestrado Integrado em Medicina Veterinária, Ciências Veterinárias A Dermatologia, em Medicina Veterinária, é uma área que representa entre 25 a 30% do total de consultas em animais de companhia, apresentando uma relação de proximidade crescente em relação à medicina humana. O presente trabalho teve como objetivos principais os seguintes estudos de caso: 1) Determinação da incidência de afeções dermatológicas e caracterização dos animais admitidos à consulta de especialida...

Agressividade tributária: um survey da literatura

Directory of Open Access Journals (Sweden)

Antonio Lopo Martinez

2017-01-01

Full Text Available Objetivo e Método: o objetivo deste artigo é revisar os estudos internacionais e no Brasil sobre a agressividade tributária, esta entendida como o comportamento de tentar evitar ou minimizar o ônus tributário explícito para a corporação. Enquanto tema de pesquisa acadêmica, o tax aggressiveness ou tax avoidance revela-se em um tópico diversificado e vasto, embora relativamente recente. Resultados e Contribuições: Entre as perguntas de pesquisa que nessa temática se desenvolvem, destaquem-se a identificação de quais seriam os determinantes da agressividade tributária da firma, apreciando: (i características das firmas; (ii atributos ambientais; (iii restrições de gatekeepers; e (iv incentivos para as firmas. Revisam-se os determinantes da agressividade tributária dos gestores e a influência da governança e estrutura de controle. Adicionalmente, identificam-se as potenciais consequências econômico-financeiras da agressividade tributária para as firmas e as proxies empíricas existentes para mensurar a agressividade tributária. O estudo se encerra com a apresentação de oportunidades futuras de pesquisa na temática.

Sequential Computerized Mastery Tests--Three Simulation Studies

Science.gov (United States)

Wiberg, Marie

2006-01-01

A simulation study of a sequential computerized mastery test is carried out with items modeled with the 3 parameter logistic item response theory model. The examinees' responses are either identically distributed, not identically distributed, or not identically distributed together with estimation errors in the item characteristics. The…

Camptocormia secundária à polimiosite

Directory of Open Access Journals (Sweden)

Melina Andrade Mattar

2013-08-01

Full Text Available A camptocormia é uma doença postural caracterizada por flexão anormal da coluna toracolombar que surge na posição ereta, aumenta durante a caminhada e desaparece na posição supina. Na literatura, há descrição de apenas cinco casos de camptocormia secundária a miopatias inflamatórias idiopáticas. No presente relato de caso, descrevemos um paciente do sexo masculino, de 67 anos, com polimiosite há 18 anos, cursando com quadro compatível com camptocormia (estável e sem progressão do quadro clínico. A polimiosite é uma miopatia inflamatória idiopática caracterizada clinicamente por fraqueza muscular simétrica predominantemente proximal dos membros. Entretanto, sendo uma doença autoimune sistêmica, é plausível que ocorra acometimento de musculatura esquelética de forma difusa, incluindo a paravertebral, podendo manifestar-se com camptocormia.

Shear Strength Measurement Benchmarking Tests for K Basin Sludge Simulants

Energy Technology Data Exchange (ETDEWEB)

Burns, Carolyn A.; Daniel, Richard C.; Enderlin, Carl W.; Luna, Maria; Schmidt, Andrew J.

2009-06-10

Equipment development and demonstration testing for sludge retrieval is being conducted by the K Basin Sludge Treatment Project (STP) at the MASF (Maintenance and Storage Facility) using sludge simulants. In testing performed at the Pacific Northwest National Laboratory (under contract with the CH2M Hill Plateau Remediation Company), the performance of the Geovane instrument was successfully benchmarked against the M5 Haake rheometer using a series of simulants with shear strengths (τ) ranging from about 700 to 22,000 Pa (shaft corrected). Operating steps for obtaining consistent shear strength measurements with the Geovane instrument during the benchmark testing were refined and documented.

Comparison of driving simulator performance and neuropsychological testing in narcolepsy.

Science.gov (United States)

Kotterba, Sylvia; Mueller, Nicole; Leidag, Markus; Widdig, Walter; Rasche, Kurt; Malin, Jean-Pierre; Schultze-Werninghaus, Gerhard; Orth, Maritta

2004-09-01

Daytime sleepiness and cataplexy can increase automobile accident rates in narcolepsy. Several countries have produced guidelines for issuing a driving license. The aim of the study was to compare driving simulator performance and neuropsychological test results in narcolepsy in order to evaluate their predictive value regarding driving ability. Thirteen patients with narcolepsy (age: 41.5+/-12.9 years) and 10 healthy control patients (age: 55.1+/-7.8 years) were investigated. By computer-assisted neuropsychological testing, vigilance, alertness and divided attention were assessed. In a driving simulator patients and controls had to drive on a highway for 60 min (mean speed of 100 km/h). Different weather and daytime conditions and obstacles were presented. Epworth Sleepiness Scale-Scores were significantly raised (narcolepsy patients: 16.7+/-5.1, controls: 6.6+/-3.6, P divided attention (56.9+/-25.4) and vigilance (58.7+/-26.8) were in a normal range. There was, however, a high inter-individual difference. There was no correlation between driving performance and neuropsychological test results or ESS Score. Neuropsychological test results did not significantly change in the follow-up. The difficulties encountered by the narcolepsy patient in remaining alert may account for sleep-related motor vehicle accidents. Driving simulator investigations are closely related to real traffic situations than isolated neuropsychological tests. At the present time the driving simulator seems to be a useful instrument judging driving ability especially in cases with ambiguous neuropsychological results.

Artes, para a didática da história

Directory of Open Access Journals (Sweden)

Luiz Giani

2012-08-01

Full Text Available Um exame das relações entre arte e ensino da história contidas no livro didático público“História: ensino médio”, do Paraná, resultou em seis grupos de arte, organizados pormodalidade: música, literatura, artes visuais, teatro, dança e cinema. A música recebeatenção especial, no gênero orquestral, por apresentar um desafio maior para historiadores,livros didáticos, professores de história e da arte. Um breve perfil da história social damúsica é um alerta sobre a importância das relações históricas entre música e ideologia: oleitor é conduzido até a guerra ideológico-musical, após a segunda guerra mundial, entremovimentos que se fizeram antagônicos, de um lado, a música nacionalista “progressista”e, de outro, a vanguarda musical, especialmente, o dodecafonismo. Embora as pesquisashistoriográficas tenham avançado, o livro didático ainda se encontra tímido, distante dosresultados das pesquisas. Pelos usos que o ensino da história possa fazer de cada arte,somente o compromisso com a emancipação humana omnilateral transforma a música ecada arte em conteúdo da história, recurso didático da história e forma de linguagem dahistória. Nenhuma arte permanece ausente desta dimensão, sem ferir a necessidadehumana, universal, de todos os homens, sem exceção.

Flight test techniques for validating simulated nuclear electromagnetic pulse aircraft responses

Science.gov (United States)

Winebarger, R. M.; Neely, W. R., Jr.

1984-01-01

An attempt has been made to determine the effects of nuclear EM pulses (NEMPs) on aircraft systems, using a highly instrumented NASA F-106B to document the simulated NEMP environment at the Kirtland Air Force Base's Vertically Polarized Dipole test facility. Several test positions were selected so that aircraft orientation relative to the test facility would be the same in flight as when on the stationary dielectric stand, in order to validate the dielectric stand's use in flight configuration simulations. Attention is given to the flight test portions of the documentation program.

Fundamental and clinical evaluation of osteocalcin RIA kit

Energy Technology Data Exchange (ETDEWEB)

Kousaka, Tadako; Yamamoto, Itsuo; Kitamura, Nobuyasu; Aoki, Jun; Uneno, Susumu; Sone, Teruki; Kasai, Ryuuichi; Torizuka, Kanji

1987-06-01

The laboratory performance of a double antibody radioimmunoassay (RIA) kit for measuring osteocalcin (OC) was tested for incubation, the effect of anticoagulants, serum storage, dilution, recovery, and reproducibility. Serum OC concentrations increased rapidly with the addition of 5 mM or more ethylenediamine tetraacetic acid, although they were not affected by the addition of heparin. Serum OC measurements, obtained at 2 or 3 weeks after sampling, tended to be lower. The other items, except for dilution, were reliable. Using the OC RIA kit, serum OC concentrations were measured in 161 patients with various diseases and 408 volunteers. Normal upper limit for OC was defined as 11.48 ng/ml. Serum OC concentrations were extremely high up to the age of puberty, and thereafter decreased rapidly with the constant values after the age of 20. Women had increased OC values after the latter half of their fourties. Primary hyperparathyroidism, bone metastases of malignancy, and malignant hypercalcemia were occasionally associated with increased OC values, in contrast to hypoparathyroidism showing decreased OC values. Extremely high values of OC were seen in many of the dialysis patients. (Namekawa, K.).

Fat Tail Model for Simulating Test Systems in Multiperiod Unit Commitment

Directory of Open Access Journals (Sweden)

J. A. Marmolejo

2015-01-01

Full Text Available This paper describes the use of Chambers-Mallows-Stuck method for simulating stable random variables in the generation of test systems for economic analysis in power systems. A study that focused on generating test electrical systems through fat tail model for unit commitment problem in electrical power systems is presented. Usually, the instances of test systems in Unit Commitment are generated using normal distribution, but in this work, simulations data are based on a new method. For simulating, we used three original systems to obtain the demand behavior and thermal production costs. The estimation of stable parameters for the simulation of stable random variables was based on three generally accepted methods: (a regression, (b quantiles, and (c maximum likelihood, choosing one that has the best fit of the tails of the distribution. Numerical results illustrate the applicability of the proposed method by solving several unit commitment problems.

Unes pinzellades d'Història

OpenAIRE

Cedó, Ferran

2006-01-01

Al llarg de la història, hi ha hagut personatges famosos que han contribuït notablement a l’evolució de la matemàtica. Aquí, presentem una ressenya biogràfica d’alguns d’ells. Això no vol dir que aquests siguin els més importants. La història de la matemàtica és llarga i complexa, i és difícil decidir quins han estat els que han incidit més en el seu desenvolupament.

Tests of numerical simulation algorithms for the Kubo oscillator

International Nuclear Information System (INIS)

Fox, R.F.; Roy, R.; Yu, A.W.

1987-01-01

Numerical simulation algorithms for multiplicative noise (white or colored) are tested for accuracy against closed-form expressions for the Kubo oscillator. Direct white noise simulations lead to spurious decay of the modulus of the oscillator amplitude. A straightforward colored noise algorithm greatly reduces this decay and also provides highly accurate results in the white noise limit

SCANAIR: A transient fuel performance code

International Nuclear Information System (INIS)

Moal, Alain; Georgenthum, Vincent; Marchand, Olivier

2014-01-01

Highlights: • Since the early 1990s, the code SCANAIR is developed at IRSN. • The software focuses on studying fast transients such as RIA in light water reactors. • The fuel rod modelling is based on a 1.5D approach. • Thermal and thermal-hydraulics, mechanical and gas behaviour resolutions are coupled. • The code is used for safety assessment and integral tests analysis. - Abstract: Since the early 1990s, the French “Institut de Radioprotection et de Sûreté Nucléaire” (IRSN) has developed the SCANAIR computer code with the view to analysing pressurised water reactor (PWR) safety. This software specifically focuses on studying fast transients such as reactivity-initiated accidents (RIA) caused by possible ejection of control rods. The code aims at improving the global understanding of the physical mechanisms governing the thermal-mechanical behaviour of a single rod. It is currently used to analyse integral tests performed in CABRI and NSRR experimental reactors. The resulting validated code is used to carry out studies required to evaluate margins in relation to criteria for different types of fuel rods used in nuclear power plants. Because phenomena occurring during fast power transients are complex, the simulation in SCANAIR is based on a close coupling between several modules aimed at modelling thermal, thermal-hydraulics, mechanical and gas behaviour. During the first stage of fast power transients, clad deformation is mainly governed by the pellet–clad mechanical interaction (PCMI). At the later stage, heat transfers from pellet to clad bring the cladding material to such high temperatures that the boiling crisis might occurs. The significant over-pressurisation of the rod and the fact of maintaining the cladding material at elevated temperatures during a fairly long period can lead to ballooning and possible clad failure. A brief introduction describes the context, the historical background and recalls the main phenomena involved under

SCANAIR: A transient fuel performance code

Energy Technology Data Exchange (ETDEWEB)

Moal, Alain, E-mail: alain.moal@irsn.fr; Georgenthum, Vincent; Marchand, Olivier

2014-12-15

Highlights: • Since the early 1990s, the code SCANAIR is developed at IRSN. • The software focuses on studying fast transients such as RIA in light water reactors. • The fuel rod modelling is based on a 1.5D approach. • Thermal and thermal-hydraulics, mechanical and gas behaviour resolutions are coupled. • The code is used for safety assessment and integral tests analysis. - Abstract: Since the early 1990s, the French “Institut de Radioprotection et de Sûreté Nucléaire” (IRSN) has developed the SCANAIR computer code with the view to analysing pressurised water reactor (PWR) safety. This software specifically focuses on studying fast transients such as reactivity-initiated accidents (RIA) caused by possible ejection of control rods. The code aims at improving the global understanding of the physical mechanisms governing the thermal-mechanical behaviour of a single rod. It is currently used to analyse integral tests performed in CABRI and NSRR experimental reactors. The resulting validated code is used to carry out studies required to evaluate margins in relation to criteria for different types of fuel rods used in nuclear power plants. Because phenomena occurring during fast power transients are complex, the simulation in SCANAIR is based on a close coupling between several modules aimed at modelling thermal, thermal-hydraulics, mechanical and gas behaviour. During the first stage of fast power transients, clad deformation is mainly governed by the pellet–clad mechanical interaction (PCMI). At the later stage, heat transfers from pellet to clad bring the cladding material to such high temperatures that the boiling crisis might occurs. The significant over-pressurisation of the rod and the fact of maintaining the cladding material at elevated temperatures during a fairly long period can lead to ballooning and possible clad failure. A brief introduction describes the context, the historical background and recalls the main phenomena involved under

Forced vibration tests and simulation analyses of a nuclear reactor building. Part 2: simulation analyses

International Nuclear Information System (INIS)

Kuno, M.; Nakagawa, S.; Momma, T.; Naito, Y.; Niwa, M.; Motohashi, S.

1995-01-01

Forced vibration tests of a BWR-type reactor building. Hamaoka Unit 4, were performed. Valuable data on the dynamic characteristics of the soil-structure interaction system were obtained through the tests. Simulation analyses of the fundamental dynamic characteristics of the soil-structure system were conducted, using a basic lumped mass soil-structure model (lattice model), and strong correlation with the measured data was obtained. Furthermore, detailed simulation models were employed to investigate the effects of simultaneously induced vertical response and response of the adjacent turbine building on the lateral response of the reactor building. (author). 4 refs., 11 figs

Improvement of the Longitudinal Beam Dynamics Tuning Procedure for the MSU RIA Driver Linac

CERN Document Server

Doleans, Marc; Grimm, Terry L; Marti, Felix; Wu, Xiaoyu; York, Richard

2005-01-01

The Rare Isotope Accelerator (RIA) driver linac will use a superconducting, cw linac with independently phased superconducting radio frequency cavities for acceleration and, for the heavier ions, utilize beams of multiple-charge-states (multi-q). Given the acceleration of multi-q beams and a stringent beam loss requirement in the RIA driver linac, a new beam envelope code capable of simulating nonlinearities of the multi-q beam envelopes in the longitudinal phase space was developed. Using optimization routines, the code is able to maximize the linearity of the longitudinal phase space motion and thereby minimizing beam loss by finding values for the amplitude and phase of the cavities for a given accelerating lattice. Relative motion of the multi-q beams is also taken into account so that superposition of the beam centroids and matching of their Twiss parameters are automatically controlled. As a result, the linac tuning procedure has been simplified and the longitudinal lattice performance has been improved...

Reanimation of the RICH Test Beam Simulation in GEANT4

CERN Document Server

Arzymatov, Kenenbek

2017-01-01

This test was originally developed by Sajan Easo (LHCb) ten years ago mostly for the purpose of testing the behavior of photomultipliers, but it wasn’t used in regression testing in Gauss/Geant4 famework. The goal of project is to revive simulation of cherenkov radiaton test by completing.

MEMÓRIA SOCIAL E INDIVIDUALIZAÇÃO NA TRAJETÓRIA DE ATORES ENGAJADOS EM PROJETOS DE EDUCAÇÃO PATRIMONIAL

Directory of Open Access Journals (Sweden)

Rodrigo Manoel Dias da Silva

Full Text Available RESUMO: Assumindo a hipótese de Joel Candau acerca da vigência hodierna de processos de individualização e fragmentação das memórias sociais, o presente artigo objetivou analisar as correspondências entre memória social e individualização na trajetória de atores sociais engajados em projetos de educação patrimonial no Brasil. Para tal, mobilizou duas estratégias analíticas. Na primeira, visou sumariar os principais contornos dos processos de individualização na modernidade e suas dimensões institucionais, sob inspiração da abordagem sociológica de Ulrich Beck. Na segunda, a partir de estudo empírico, objetivou analisar a trajetória de um ator envolvido em práticas de educação patrimonial, a fim de examinar a composição das pautas de suas proposições políticas e a suposta individualização de suas intervenções nos municípios em que atua.

Modeling and simulation for microelectronic packaging assembly manufacturing, reliability and testing

CERN Document Server

Liu, Sheng

2011-01-01

Although there is increasing need for modeling and simulation in the IC package design phase, most assembly processes and various reliability tests are still based on the time consuming ""test and try out"" method to obtain the best solution. Modeling and simulation can easily ensure virtual Design of Experiments (DoE) to achieve the optimal solution. This has greatly reduced the cost and production time, especially for new product development. Using modeling and simulation will become increasingly necessary for future advances in 3D package development.  In this book, Liu and Liu allow people

EFEITO ANTIBIÓTICO DO PRÓPOLIS SOBRE BACTÉRIAS FITOPATOGÊNICAS

Directory of Open Access Journals (Sweden)

L. BIANCHINI

1998-01-01

Full Text Available O efeito antibiótico de extrato aquoso de própolis, em várias concentrações, foi avaliado para cinco espécies de bactérias fitopatogênicas. Agrobacterium tumefaciens, Clavibacter michiganensis subsp. michiganensis e Xanthomonas axonopodis pv. phaseoli foram completamente inibidas em meio de cultura contendo 10% de extrato de própolis. Erwinia chrysanthemi foi parcialmente inibida, enquanto Pseudomonas syringae pv. tabaci se mostrou insensível ao extrato, desenvolvendo colônias idênticas àquelas observadas em meios livres de própolis. Concentrações menores não foram suficientes para exercer um efeito antimicrobiano desejável sobre as bactérias pertencentes a todas as espécies testadas. Resultados idênticos foram obtidos quando própolis foi incorporado ao meio antes ou após a autoclavagem, demonstrando que a substância ativa presente no extrato não é termosensível. Foi demonstrado, portanto, o uso potencial do própolis como antibiótico para o controle de bactérias fitopatogênicas.The antibiotic effect of aqueous extract of propolis was evaluated in vitro against five species of bacteria. The growth of Agrobacterium tumefaciens, Clavibacter michiganensis subsp. michiganensis and Xanthomonas axonopodis pv. phaseoli was completely inhibited in a medium containing 10% of propolis. Erwinia chrysanthemi was partially inhibited and Pseudomonas syringae pv. tabaci was not affected. Lower concentration of the aqueous extract was not effective to promote a desirable antibiotic action against all bacterial species tested. The active ingredient present in the propolis was thermostable. The potential use of the propolis to control phytopathogenic bacteria was demonstrated.

HISTÓRIA ORAL ENTRE REFLEXÕES E MEMÓRIAS: Revisitando o percurso de Antônio Torres Montenegro e suas trilhas metodológicas do fazer historiográfico

Directory of Open Access Journals (Sweden)

Erinaldo Vicente Cavalcanti

2016-05-01

  Antônio Torres Montenegro pesquisador pernambucano de reconhecida atuação no uso da metodologia da história oral. Seus estudos acerca das relações entre a história e memória, teoria da história e lutas políticas no âmbito da História do Brasil Contemporâneo têm ressonâncias nacionais e internacionais. Graduado em Filosofia pela Universidade Católica de Pernambuco (UNICAP, 1974, mestre e doutor em História pela Universidade Estadual de Campinas (Unicamp, 1983/1991, realizou seu estágio pós-doutoral na State University of New York - Stony Brook (2000 e na Universidade Federal Fluminense (UFF, 2016. Ao longo de sua carreira acadêmica, no campo da história, publicou inúmeros artigos em periódicos nacionais e internacionais, organizou e/ou publicou vários livros e capítulos de livros. Participou de aproximadamente 100 bancas de defesas de dissertações e teses e de inúmeros eventos acadêmicos regionais, nacionais e internacionais. Atua do Conselho Editorial de importantes periódicos nacionais na área de história, a exemplo Territórios e Fronteiras do Programa de Pós-Graduação da Universidade Federal de Mato Grosso (UFMT da Revista História Oral da Associação Brasileira de História Oral (ABHO da Revista Tempo do Departamento de História da Universidade Federal Fluminense (UFF entre outras.

História e Memória: o caso do Ferrugem

Directory of Open Access Journals (Sweden)

Myrian Sepúlveda dos Santos

2003-01-01

Full Text Available O objetivo deste artigo é analisar o uso da memória pelas Ciências Sociais a partir da investigação de fontes orais e escritas. Ao longo do trabalho, serão consideradas cinco narrativas sobre o assassinato de um lavrador da Ilha Grande por um grupo de presos que havia fugido do Instituto Penal Cândido Mendes (IPCM. Além disso, são objetos de análise a notícia sobre o caso que aparece na imprensa e o relatório oficial sobre a fuga dos presos encaminhado pelo diretor da penitenciária ao diretor-geral do Departamento do Sistema Penitenciário (DESIPE. Em que pese a diferença entre os relatos apresentados, procurar-se-á mostrar que as memórias relacionam-se a perspectivas e códigos existentes entre grupos de pertencimento e que elas podem fornecer dados importantes sobre contextos, processos e conflitos sociais que fazem parte da vida dos diversos narradores do caso em questão.The objective of this paper is to investigate social practices developed by inmates of the Instituto Penal Cândido Mendes (IPCM as well as by those who lived in Ilha Grande, the island where the prison was settled, through the analysis of different narratives about the escape of a group of convicts. The author also analyzed the escape on the news and on the official reports. The point the author makes is that despite the different reports on the escape it is possible to relate the narrative to collective memories, that is, to common rules and perspectives, which allow us to understand social conflicts, processes and contexts inherent to the lives of the narrators.

O Jornalismo nas Rádios Comunitárias

OpenAIRE

Rosembach, Cilto José

2006-01-01

O presente estudo analisa o jornalismo nas rádios comunitárias a partir do paradigma da comunicação popular, alternativa e da contextualização histórica das rádios comunitárias no Brasil. A programação jornalística de duas rádios comunitárias no Estado de São Paulo é analisada a partir do referencial teórico que elucida a comunicação popular e prioriza os conceitos de jornalismo popular. São analisadas a Rádio Cantareira FM 107,5, de Vila Isabel, distrito de Brasilândia, São...

Study of behavior of cermet fuel elements on IGR reactor under RIA type accident condition

International Nuclear Information System (INIS)

Vasil'ev, Yu.S.; Vurim, A.D.; Koltyshev, S.M.; Pakhnits, V.A.; Tukhvatulin, Sh.T.; Popov, V.V.; Ryzhkov, A.N.

1996-01-01

In 1993 December in IGR reactor of Inst. of Atomic Energy of National Nuclear Center of Republic of Kazakstan the second batch of in-pile testing of perspective cermet fuel elements under the condition, simulating RIA type accident was conducted. In the second batch of testing during eight start-ups 10 cermet fuel elements were examined. Among which 8 of monolith type and 2 fuel elements with false jacket beside cladding (FJF), as well as, 6 standard fuel elements of WWER-1000 type reactor with dioxide fuel were tested. 2 fuel elements - cermet and standard were placed into capsule filled with water. To measure energy release for the each start-up two fission monitor and inside core control gauge were placed. In all the start-ups operation mode of IGR was neutron pulse. Power of fuel element kept changing from 151 to 336 k W; energy release was 38-93 kJ/gr m 235 U; maximum temperature of cermet fuel was 1943-2173 K, of dioxide fuel - 1923-2843 K. The testing has demonstrated that operability of cermet fuel elements under reactivity accident condition with pulse width of 0,2 s is, at least, not less that operability of dioxide fuel elements, through advantages of cermet fuel under these conditions are revealed to the least extent

First experiences with commercial RIA kits for prostatic acid phosphatase (PAP)

Energy Technology Data Exchange (ETDEWEB)

Boettger, I; Langhammer, H; Pabst, H W; Sintermann, R

1980-06-01

Five commercial PAP RIA kits were intercompared by common RIA quality control criteria. All RIAs performed basically well although some differences existed in respect to concentration range, specific and non-specific binding, 50%-intercept, sensitivity and measurements of serum PAP in male and female controls. The latter finding may have been due to differences in antigen purity, antiserum specificity and composition of the assay medium employed. Good correlation was found between PAP determination by RIA and by enzyme assay. First measurements of PAP in patients treated for prostatic carcinoma being performed for orientation purposes are demonstrated. The PAP RIA has been introduced into our routine diagnostic and follow-up of prostatic carcinoma.

Prevalência de alta reatividade plaquetária em pacientes tratados com aspirina encaminhados para angiografia coronária

Directory of Open Access Journals (Sweden)

André Manica

Full Text Available FUNDAMENTO: A aspirina (Ácido Acetilsalicílico - AAS é capaz de reduzir eventos adversos cardiovasculares em pacientes portadores de Doença Arterial Coronariana (DAC através da inibição da atividade plaquetária. Alguns pacientes com DAC, apesar da terapia com AAS, apresentam Alta Reatividade Plaquetária (ARP, o que determina um maior risco para o desenvolvimento de eventos cardiovasculares. OBJETIVO: O objetivo deste estudo foi determinar a prevalência de ARP em pacientes tratados com AAS e encaminhados para cinecoronariografia, além de avaliar se existe uma possível correlação entre a gravidade da DAC e o desenvolvimento de ARP. MÉTODOS: Estudo de centro único onde foram incluídos 115 pacientes consecutivos, tratados com AAS e portadores de DAC estável. A reatividade plaquetária induzida pelo ADP e colágeno foram avaliadas através da Agregometria de Transmitância Luminosa (ATL. Pacientes com agregação plaquetária maior que 70%, induzida por ambos os reagentes, foram classificados como tendo ARP e, neste grupo, a adesão ao tratamento com AAS foi avaliada através da dosagem dos níveis séricos de salicilato. RESULTADOS: A média de idade foi de 60,9 anos e a dose média de AAS foi de 164,2 mg. Tabagismo e diabetes melito estavam presentes em 28,7% e 31,5% dos pacientes, respectivamente. Foi encontrada ARP em 14 pacientes (13%, entretanto, em sete indivíduos (50% com ARP observaram-se baixos níveis séricos de salicilato (< 2,0 µg/mL, sugerindo não adesão à terapia medicamentosa. Em 6,5% dos pacientes com ARP identificou-se níveis detectáveis de salicilato sérico, sugerindo uma eficácia reduzida do AAS. A ARP se correlacionou com o número e a gravidade das estenoses coronárias (p = 0,04. CONCLUSÃO: Em uma população de pacientes tratados com AAS e encaminhados para angiografia coronária, a reatividade plaquetária elevada é prevalente (13%, sendo 50% destes pacientes não aderentes à terapia farmacol

Recidiva de urticária crônica decorrente de reinfecção por Helicobacter pylori

Directory of Open Access Journals (Sweden)

Dayanne Mota V. Bruscky

2013-06-01

Full Text Available OBJETIVO: Descrever, em uma adolescente do sexo feminino, o caso clínico de urticária crônica associado à infecção por Helicobacter pylori confirmado em dois momentos distintos, com melhora após a terapêutica antibacteriana. DESCRIÇÃO DO CASO: Paciente do sexo feminino, 13 anos, procurou atendimento médico com urticária crônica e dores epigástricas sem resposta ao tratamento medicamentoso. Os exames solicitados para investigação complementar apresentaram-se normais, exceto a endoscopia digestiva alta com biópsia, que evidenciou gastrite crônica ativa moderada associada ao Helicobacter pylori. Foi iniciado o tratamento adequado para a bactéria em questão e a paciente apresentou remissão dos sintomas. Nova endoscopia digestiva alta para controlar o tratamento após nove meses estava normal. Cinco anos depois, a paciente procurou novamente o ambulatório queixando-se de retorno do quadro de urticária e dores epigástricas. Ela se encontrava em uso de anti-histamínico, sem melhora. Foi novamente submetida a protocolo de exames para investigar urticária crônica, com resultados dentro da normalidade. Foi submetida à endoscopia digestiva alta, que apresentou teste da urease positivo. Iniciou-se então novo tratamento para Helicobacter pylori por sete dias, com desaparecimento da urticária crônica e das dores epigástricas. COMENTÁRIOS: O caso relatado sugere relação causal entre o diagnóstico positivo para o Helicobacter pylori e a ocorrência do quadro de urticária crônica, com instituição de terapêutica eficaz para tal bactéria e remissão dos sintomas. A urticária crônica é uma doença de etiopatogenia complexa e, apesar das controvérsias, as evidências do envolvimento do Helicobacter pylori com doenças extraintestinais vêm crescendo, entre elas a urticária crônica.

Simulation Facilities and Test Beds for Galileo

Science.gov (United States)

Schlarmann, Bernhard Kl.; Leonard, Arian

2002-01-01

Galileo is the European satellite navigation system, financed by the European Space Agency (ESA) and the European Commission (EC). The Galileo System, currently under definition phase, will offer seamless global coverage, providing state-of-the-art positioning and timing services. Galileo services will include a standard service targeted at mass market users, an augmented integrity service, providing integrity warnings when fault occur and Public Regulated Services (ensuring a continuity of service for the public users). Other services are under consideration (SAR and integrated communications). Galileo will be interoperable with GPS, and will be complemented by local elements that will enhance the services for specific local users. In the frame of the Galileo definition phase, several system design and simulation facilities and test beds have been defined and developed for the coming phases of the project, respectively they are currently under development. These are mainly the following tools: Galileo Mission Analysis Simulator to design the Space Segment, especially to support constellation design, deployment and replacement. Galileo Service Volume Simulator to analyse the global performance requirements based on a coverage analysis for different service levels and degrades modes. Galileo System Simulation Facility is a sophisticated end-to-end simulation tool to assess the navigation performances for a complete variety of users under different operating conditions and different modes. Galileo Signal Validation Facility to evaluate signal and message structures for Galileo. Galileo System Test Bed (Version 1) to assess and refine the Orbit Determination &Time Synchronisation and Integrity algorithms, through experiments relying on GPS space infrastructure. This paper presents an overview on the so called "G-Facilities" and describes the use of the different system design tools during the project life cycle in order to design the system with respect to

Thyroxine determination in serum by radioimmunoassay and competitive protein-binding analysis (simultaneous study using four test kits)

International Nuclear Information System (INIS)

Wagner, K.

1978-01-01

Three commercial test kits for radioimmunological T 4 -determination have been tested (T 4 -RIA Abbott, RIA-mat T 4 , T 4 -RIA Henning). The RIA method has also been compared with a CPBA test (Tetralute) for routine application. 1) The results show that CPBA (Tetralute) is superior over the three radioimmuno-assays with regard to intra-assay variance. The T 4 -RIA Abbott has been inferior to the two other RIA under test and to the Tetralute with regard to inter-assay variance. 2) The four test kits show significant differences and considerable deviations from the given nominal values in comparison with the mean values of two control sera. A control for correctness does not seem to be appropriate as it cannot be decided which of the test kits yields the true value of T 4 content. No systematic difference has been observed between RIA and CPBA in the determination of T 4 in control sera. 3) No detectable difference has been found among the RIA-T 4 test kits and comparing them with the CBPA test regarding their diagnostic precision. A good correlation of T 4 values of euthyroid patients comparing the Tetralute and the three radioimmunological test kits. The mean values of euthyroid sera obtained by the three radioimmuno-assays and the Tetralute are not in agreement with each other. (orig.) [de

Magnetic Testing, and Modeling, Simulation and Analysis for Space Applications

Science.gov (United States)

Boghosian, Mary; Narvaez, Pablo; Herman, Ray

2012-01-01

The Aerospace Corporation (Aerospace) and Lockheed Martin Space Systems (LMSS) participated with Jet Propulsion Laboratory (JPL) in the implementation of a magnetic cleanliness program of the NASA/JPL JUNO mission. The magnetic cleanliness program was applied from early flight system development up through system level environmental testing. The JUNO magnetic cleanliness program required setting-up a specialized magnetic test facility at Lockheed Martin Space Systems for testing the flight system and a testing program with facility for testing system parts and subsystems at JPL. The magnetic modeling, simulation and analysis capability was set up and performed by Aerospace to provide qualitative and quantitative magnetic assessments of the magnetic parts, components, and subsystems prior to or in lieu of magnetic tests. Because of the sensitive nature of the fields and particles scientific measurements being conducted by the JUNO space mission to Jupiter, the imposition of stringent magnetic control specifications required a magnetic control program to ensure that the spacecraft's science magnetometers and plasma wave search coil were not magnetically contaminated by flight system magnetic interferences. With Aerospace's magnetic modeling, simulation and analysis and JPL's system modeling and testing approach, and LMSS's test support, the project achieved a cost effective approach to achieving a magnetically clean spacecraft. This paper presents lessons learned from the JUNO magnetic testing approach and Aerospace's modeling, simulation and analysis activities used to solve problems such as remnant magnetization, performance of hard and soft magnetic materials within the targeted space system in applied external magnetic fields.

Urticária aquagênica familiar: relato de dois casos e revisão da literatura Familial aquagenic urticaria: report of two cases and literature review

Directory of Open Access Journals (Sweden)

Maria Bandeira de Melo Paiva Seize

2009-10-01

Full Text Available Urticária aquagênica é forma rara de urticária física caracterizada por aparecimento de urticas após o contato com água, independente da temperatura. Há poucos casos descritos de urticária aquagênica e, destes, somente cinco da forma familiar. Apresentamos o primeiro relato de urticária aquagênica familiar no Brasil, acometendo mãe e filha. Ambas apresentavam urticas, principalmente após banho de chuveiro, independentemente da temperatura da água. A mãe referia ter o quadro há quatro anos, e a filha, desde o nascimento. Para diagnóstico, foram realizados testes de provocação com água, com aparecimento de lesões em ambas, e testes com dermografômetro, com cubo de gelo envolvido em plástico e de provocação para urticária colinérgica, sem o aparecimento de lesões, excluindo assim outras formas de urticária física.Aquagenic urticaria is a rare form of physical urticaria, characterized by pruritic wheals that appear following contact with water, independently of its temperature. There are few reports of cases of aquagenic urticaria, and only five include the familial form. We present the first case of familial aquagenic urticaria in Brazil (mother and daughter. Both patients presented wheals following contact with water, especially when showering, regardless of its temperature. The mother reported onset of urticaria four years before and the daughter presented wheals since birth. For diagnostic purposes, they were submitted to a challenge test with water, and both subjects presented wheals, as well as to tests using ice cubes in plastic bag with dermographometer and challenge tests for cholinergic urticaria, with no appearance of lesions, excluding other forms of physical urticaria.

Simulation of thermohydraulic phenomena and model test for FBR

International Nuclear Information System (INIS)

Satoh, Kazuziro

1994-01-01

This paper summarizes the major thermohydraulic phenomena of FBRs and the conventional ways of their model tests, and introduces the recent findings regarding measurement technology and computational science. In the future commercial stage of FBRs, the design optimization will becomes important to improve economy and safety more and more. It is indispensable to use computational science to the plant design and safety evaluation. The most of the model tests will be replaced by the simulation analyses based on computational science. The measurement technology using ultrasonic and the numerical simulation with super parallel computing are considered to be the key technology to realize the design by analysis method. (author)

ROSA-IV Large Scale Test Facility (LSTF) system description for second simulated fuel assembly

International Nuclear Information System (INIS)

1990-10-01

The ROSA-IV Program's Large Scale Test Facility (LSTF) is a test facility for integral simulation of thermal-hydraulic response of a pressurized water reactor (PWR) during small break loss-of-coolant accidents (LOCAs) and transients. In this facility, the PWR core nuclear fuel rods are simulated using electric heater rods. The simulated fuel assembly which was installed during the facility construction was replaced with a new one in 1988. The first test with this second simulated fuel assembly was conducted in December 1988. This report describes the facility configuration and characteristics as of this date (December 1988) including the new simulated fuel assembly design and the facility changes which were made during the testing with the first assembly as well as during the renewal of the simulated fuel assembly. (author)

Aprendizado e memória Learning and memory

Directory of Open Access Journals (Sweden)

Paul Lombroso

2004-09-01

Full Text Available A memória é dividida de duas grandes formas: explícita e implícita. O hipocampo é necessário para a formação das memórias explícitas, ao passo que várias outras regiões do cérebro, incluindo o estriado, a amígdala e o nucleus accumbens, estão envolvidos na formação das memórias implícitas. A formação de todas as memórias requer alterações morfológicas nas sinapses: novas sinapses devem ser formadas ou antigas precisam ser fortalecidas. Considera-se que essas alterações reflitam a base celular subjacente das memórias persistentes. Consideráveis avanços têm ocorrido na última década em relação a nossa compreensão sobre as bases moleculares da formação dessas memórias. Um regulador-chave da plasticidade sináptica é uma via de sinalização que inclui a proteína-quinase ativada por mitógenos (MAP. Como essa via é necessária para a memória e o aprendizado normais, não é surpreendente que as mutações nos membros dessa via levem a prejuízos no aprendizado. A neurofibromatose, a síndrome de Coffin-Lowry e a de Rubinstein-Taybi são três exemplos de transtornos de desenvolvimento que apresentam mutações em componentes-chave na via de sinalização da proteína-quinase MAP.Memory is broadly divided into declarative and nondeclarative forms of memory. The hippocampus is required for the formation of declarative memories, while a number of other brain regions including the striatum, amygdala and nucleus accumbens are involved in the formation of nondeclarative memories. The formation of all memories require morphological changes of synapses: new ones must be formed or old ones strengthened. These changes are thought to reflect the underlying cellular basis for persistent memories. Considerable advances have occurred over the last decade in our understanding of the molecular bases of how these memories are formed. A key regulator of synaptic plasticity is a signaling pathway that includes the mitogen

TEMPEST code modifications and testing for erosion-resisting sludge simulations

International Nuclear Information System (INIS)

Onishi, Y.; Trent, D.S.

1998-01-01

The TEMPEST computer code has been used to address many waste retrieval operational and safety questions regarding waste mobilization, mixing, and gas retention. Because the amount of sludge retrieved from the tank is directly related to the sludge yield strength and the shear stress acting upon it, it is important to incorporate the sludge yield strength into simulations of erosion-resisting tank waste retrieval operations. This report describes current efforts to modify the TEMPEST code to simulate pump jet mixing of erosion-resisting tank wastes and the models used to test for erosion of waste sludge with yield strength. Test results for solid deposition and diluent/slurry jet injection into sludge layers in simplified tank conditions show that the modified TEMPEST code has a basic ability to simulate both the mobility and immobility of the sludges with yield strength. Further testing, modification, calibration, and verification of the sludge mobilization/immobilization model are planned using erosion data as they apply to waste tank sludges

Finite element simulation of asphalt fatigue testing

DEFF Research Database (Denmark)

Ullidtz, Per; Kieler, Thomas Lau; Kargo, Anders

1997-01-01

The traditional interpretation of fatigue tests on asphalt mixes has been in terms of a logarithmic linear relationship between the constant stress or strain amplitude and the number of load repetitions to cause failure, often defined as a decrease in modulus to half the initial value...... damage mechanics.The paper describes how continuum damage mechanics may be used with a finite element program to explain the progressive deterioration of asphalt mixes under laboratory fatigue testing. Both constant stress and constant strain testing are simulated, and compared to the actual results from...... three point and four point fatigue test on different mixes. It is shown that the same damage law, based on energy density, may be used to explain the gradual deterioration under constant stress as well as under constant strain testing.Some of the advantages of using this method for interpreting fatigue...

Remote Infrared Audible Signage (RIAS) Pilot Program : evaluation report

Science.gov (United States)

2009-09-01

This report presents evaluation findings on the Remote Infrared Audible Signage (RIAS) Pilot Program in the Puget Sound Region of Washington. The installation, demonstration and evaluation of RIAS were required by a provision in the Safe, Accountable...

Simulation technologies in networking and communications selecting the best tool for the test

CERN Document Server

Pathan, Al-Sakib Khan; Khan, Shafiullah

2014-01-01

Simulation is a widely used mechanism for validating the theoretical models of networking and communication systems. Although the claims made based on simulations are considered to be reliable, how reliable they really are is best determined with real-world implementation trials.Simulation Technologies in Networking and Communications: Selecting the Best Tool for the Test addresses the spectrum of issues regarding the different mechanisms related to simulation technologies in networking and communications fields. Focusing on the practice of simulation testing instead of the theory, it presents

Atomistic Simulations of Small-scale Materials Tests of Nuclear Materials

International Nuclear Information System (INIS)

Shin, Chan Sun; Jin, Hyung Ha; Kwon, Jun Hyun

2012-01-01

Degradation of materials properties under neutron irradiation is one of the key issues affecting the lifetime of nuclear reactors. Evaluating the property changes of materials due to irradiations and understanding the role of microstructural changes on mechanical properties are required for ensuring reliable and safe operation of a nuclear reactor. However, high dose of neuron irradiation capabilities are rather limited and it is difficult to discriminate various factors affecting the property changes of materials. Ion beam irradiation can be used to investigate radiation damage to materials in a controlled way, but has the main limitation of small penetration depth in the length scale of micro meters. Over the past decade, the interest in the investigations of size-dependent mechanical properties has promoted the development of various small-scale materials tests, e.g. nanoindentation and micro/nano-pillar compression tests. Small-scale materials tests can address the issue of the limitation of small penetration depth of ion irradiation. In this paper, we present small-scale materials tests (experiments and simulation) which are applied to study the size and irradiation effects on mechanical properties. We have performed molecular dynamics simulations of nanoindentation and nanopillar compression tests. These atomistic simulations are expected to significantly contribute to the investigation of the fundamental deformation mechanism of small scale irradiated materials

Lembrar-esquecer: trabalhando com as memórias infantis

Directory of Open Access Journals (Sweden)

Renata Sieiro Fernandes

Full Text Available Baseando-se nas obras de autores que focalizam a velhice e a memória, valemo-nos da proposta de construção de conjuntos fotográficos e da metodologia de análise para elaborar um exercício/desafio semelhante para crianças da faixa etária de 9-10 anos. Em concordância com os autores, também nos propusemos a pensar sobre como a memória das crianças - assim como a dos velhos - pode se construir e se organizar por meio de suportes fotográficos representativos de fragmentos da vida cotidiana. Os dois grupos compostos por seres que se encontram nas margens do tempo, se distanciam e se aproximam nessa particularidade. Intuitiva e reflexivamente, as crianças elaboraram seus conceitos de memória, envolvendo as lembranças e os esquecimentos, representando-os de formas visuais variadas e criativas, indicando que os movimentos constitutivos da memória dão indícios de tentativas de ordenação de um tempo composto de vários tempos.

Validation and Simulation of Ares I Scale Model Acoustic Test - 2 - Simulations at 5 Foot Elevation for Evaluation of Launch Mount Effects

Science.gov (United States)

Strutzenberg, Louise L.; Putman, Gabriel C.

2011-01-01

The Ares I Scale Model Acoustics Test (ASMAT) is a series of live-fire tests of scaled rocket motors meant to simulate the conditions of the Ares I launch configuration. These tests have provided a well documented set of high fidelity measurements useful for validation including data taken over a range of test conditions and containing phenomena like Ignition Over-Pressure and water suppression of acoustics. Expanding from initial simulations of the ASMAT setup in a held down configuration, simulations have been performed using the Loci/CHEM computational fluid dynamics software for ASMAT tests of the vehicle at 5 ft. elevation (100 ft. real vehicle elevation) with worst case drift in the direction of the launch tower. These tests have been performed without water suppression and have compared the acoustic emissions for launch structures with and without launch mounts. In addition, simulation results have also been compared to acoustic and imagery data collected from similar live-fire tests to assess the accuracy of the simulations. Simulations have shown a marked change in the pattern of emissions after removal of the launch mount with a reduction in the overall acoustic environment experienced by the vehicle and the formation of highly directed acoustic waves moving across the platform deck. Comparisons of simulation results to live-fire test data showed good amplitude and temporal correlation and imagery comparisons over the visible and infrared wavelengths showed qualitative capture of all plume and pressure wave evolution features.

Transient productivity index for numerical well test simulations

Energy Technology Data Exchange (ETDEWEB)

Blanc, G.; Ding, D.Y.; Ene, A. [Institut Francais du Petrole, Pau (France)] [and others

1997-08-01

The most difficult aspect of numerical simulation of well tests is the treatment of the Bottom Hole Flowing (BHF) Pressure. In full field simulations, this pressure is derived from the Well-block Pressure (WBP) using a numerical productivity index which accounts for the grid size and permeability, and for the well completion. This productivity index is calculated assuming a pseudo-steady state flow regime in the vicinity of the well and is therefore constant during the well production period. Such a pseudo-steady state assumption is no longer valid for the early time of a well test simulation as long as the pressure perturbation has not reached several grid-blocks around the well. This paper offers two different solutions to this problem: (1) The first one is based on the derivation of a Numerical Transient Productivity Index (NTPI) to be applied to Cartesian grids; (2) The second one is based on the use of a Corrected Transmissibility and Accumulation Term (CTAT) in the flow equation. The representation of the pressure behavior given by both solutions is far more accurate than the conventional one as shown by several validation examples which are presented in the following pages.

Concept of scaled test facility for simulating the PWR thermalhydraulic behaviour

International Nuclear Information System (INIS)

Silva Filho, E.

1990-01-01

This work deals with the design of a scaled test facility of a typical pressurized water reactor plant, to simulation of small break Loss-of-Coolant Accident. The computer code RELAP 5/ MOD1 has been utilized to simulate the accident and to compare the test facility behaviour with the reactor plant one. The results demonstrate similar thermal-hydraulic behaviours of the two sistema. (author)

História, memória e violência em Nocturno e Chile, Estrella distante e Amuleto de Roberto Bolaño

OpenAIRE

Carmen Cecilia Rodríguez Almonacid

2012-01-01

Resumo: Que pode aportar um conjunto de obras para a elaboração de uma memória? A literatura procura no passado, indaga nele querendo resgatar, desde uma perspectiva da memória histórica e da experiência individual, as formas de estabelecer um território que ajude a preservá-la. Assim, a memória é forjada e protegida ao fluir pelas páginas que a literatura cria, enriquecendo e transformando a realidade social e cultural na qual emerge. A proposta deste estudo se centra na reflexão da relação ...

Simulation-Based Testing of Pager Interruptions During Laparoscopic Cholecystectomy.

Science.gov (United States)

Sujka, Joseph A; Safcsak, Karen; Bhullar, Indermeet S; Havron, William S

2018-01-30

To determine if pager interruptions affect operative time, safety, or complications and management of pager issues during a simulated laparoscopic cholecystectomy. Twelve surgery resident volunteers were tested on a Simbionix Lap Mentor II simulator. Each resident performed 6 randomized simulated laparoscopic cholecystectomies; 3 with pager interruptions (INT) and 3 without pager interruptions (NO-INT). The pager interruptions were sent in the form of standardized patient vignettes and timed to distract the resident during dissection of the critical view of safety and clipping of the cystic duct. The residents were graded on a pass/fail scale for eliciting appropriate patient history and management of the pager issue. Data was extracted from the simulator for the following endpoints: operative time, safety metrics, and incidence of operative complications. The Mann-Whitney U test and contingency table analysis were used to compare the 2 groups (INT vs. NO-INT). Level I trauma center; Simulation laboratory. Twelve general surgery residents. There was no significant difference between the 2 groups in any of the operative endpoints as measured by the simulator. However, in the INT group, only 25% of the time did the surgery residents both adequately address the issue and provide effective patient management in response to the pager interruption. Pager interruptions did not affect operative time, safety, or complications during the simulated procedure. However, there were significant failures in the appropriate evaluations and management of pager issues. Consideration for diversion of patient care issues to fellow residents not operating to improve quality and safety of patient care outside the operating room requires further study. Copyright © 2018. Published by Elsevier Inc.

Avaliação pré-operatória: triagem por meio de questionário

Directory of Open Access Journals (Sweden)

Florentino Fernandes Mendes

2013-08-01

Full Text Available JUSTIFICATIVA E OBJETIVOS: Antes de cirurgia eletiva é indispensável conhecer com antecedência as condições clínicas do paciente. O objetivo deste estudo foi comparar a avaliação pré-operatória (APO por meio do preenchimento de um questionário com a consulta realizada pelo anestesiologista. MÉTODO: Antes da consulta pré-operatória, os pacientes responderam a um questionário com informações sobre idade, peso, altura, cirurgia planejada, história médica e cirúrgica pregressa, alergias, medicamentos e doses usadas, história social (drogas ilícitas, álcool, tabagismo, capacidade funcional e tolerância ao exercício. A consulta pré-operatória foi realizada por anestesiologista que não tinha acesso aos dados do questionário nem conhecimento da pesquisa. Os dados obtidos por meio do questionário foram comparados com a consulta pré-operatória por dois pesquisadores independentes, com a finalidade de responder às perguntas: 1 A avaliação pelo questionário foi suficiente - o paciente poderia ser conduzido à cirurgia sem necessidade da avaliação presencial? 2 Houve alguma informação relevante - capaz de mudar a conduta anestésica - que o questionário não aferiu, mas que a consulta presencial avaliou? 3 Houve alguma informação acrescentada pelo questionário de saúde que a consulta presencial não obteve? Para análise estatística usou-se o teste t de Student pareado para dados paramétricos e o teste Qui-quadrado para dados categóricos com P 30, baixa capacidade funcional, hipertensão arterial, diabetes mellitus, asma, insuficiência renal, hepatite e cardiopatia isquêmica. CONCLUSÕES: O uso do questionário foi efetivo para triagem de pacientes que necessitam de avaliação complementar e/ou alteração de regime terapêutico previamente ao procedimento eletivo. Além disso, o questionário acrescentou dados não contemplados pela avaliação clínica.

DEVELOPMENT OF AN INSOLUBLE SALT SIMULANT TO SUPPORT ENHANCED CHEMICAL CLEANING TESTS

International Nuclear Information System (INIS)

Eibling, R

2008-01-01

The closure process for high level waste tanks at the Savannah River Site will require dissolution of the crystallized salts that are currently stored in many of the tanks. The insoluble residue from salt dissolution is planned to be removed by an Enhanced Chemical Cleaning (ECC) process. Development of a chemical cleaning process requires an insoluble salt simulant to support evaluation tests of different cleaning methods. The Process Science and Engineering section of SRNL has been asked to develop an insoluble salt simulant for use in testing potential ECC processes (HLE-TTR-2007-017). An insoluble salt simulant has been developed based upon the residues from salt dissolution of saltcake core samples from Tank 28F. The simulant was developed for use in testing SRS waste tank chemical cleaning methods. Based on the results of the simulant development process, the following observations were developed: (1) A composition based on the presence of 10.35 grams oxalate and 4.68 grams carbonate per 100 grams solids produces a sufficiently insoluble solids simulant. (2) Aluminum observed in the solids remaining from actual waste salt dissolution tests is probably precipitated from sodium aluminate due to the low hydroxide content of the saltcake. (3) In-situ generation of aluminum hydroxide (by use of aluminate as the Al source) appears to trap additional salts in the simulant in a manner similar to that expected for actual waste samples. (4) Alternative compositions are possible with higher oxalate levels and lower carbonate levels. (5) The maximum oxalate level is limited by the required Na content of the insoluble solids. (6) Periodic mixing may help to limit crystal growth in this type of salt simulant. (7) Long term storage of an insoluble salt simulant is likely to produce a material that can not be easily removed from the storage container. Production of a relatively fresh simulant is best if pumping the simulant is necessary for testing purposes. The insoluble

Distributed Sensor Network Software Development Testing through Simulation

Energy Technology Data Exchange (ETDEWEB)

Brennan, Sean M. [Univ. of New Mexico, Albuquerque, NM (United States)

2003-12-01

The distributed sensor network (DSN) presents a novel and highly complex computing platform with dif culties and opportunities that are just beginning to be explored. The potential of sensor networks extends from monitoring for threat reduction, to conducting instant and remote inventories, to ecological surveys. Developing and testing for robust and scalable applications is currently practiced almost exclusively in hardware. The Distributed Sensors Simulator (DSS) is an infrastructure that allows the user to debug and test software for DSNs independent of hardware constraints. The exibility of DSS allows developers and researchers to investigate topological, phenomenological, networking, robustness and scaling issues, to explore arbitrary algorithms for distributed sensors, and to defeat those algorithms through simulated failure. The user speci es the topology, the environment, the application, and any number of arbitrary failures; DSS provides the virtual environmental embedding.

Grid Simulator for Testing a Wind Turbine on Offshore Floating Platform

Energy Technology Data Exchange (ETDEWEB)

Gevorgian, V.

2012-02-01

An important aspect of such offshore testing of a wind turbine floating platform is electrical loading of the wind turbine generator. An option of interconnecting the floating wind turbine with the onshore grid via submarine power cable is limited by many factors such as costs and associated environmental aspects (i.e., an expensive and lengthy sea floor study is needed for cable routing, burial, etc). It appears to be a more cost effective solution to implement a standalone grid simulator on a floating platform itself for electrical loading of the test wind turbine. Such a grid simulator must create a stable fault-resilient voltage and frequency bus (a micro grid) for continuous operation of the test wind turbine. In this report, several electrical topologies for an offshore grid simulator were analyzed and modeled.

Serum specimens with double HBsAg/HBsAb (s-system) or HBeAg/HBeAb (e-system) positive markers (by ELISA) cross-checked with RIA or ECLIA--a comparison

International Nuclear Information System (INIS)

Tao Hongqun; Li Xiaolong; Ye Wei

2005-01-01

Objective: To cross-check the unusually high double positive rate of s- or e-system tested with ELISA in sera specimens from hepatitis B patients with two other methods of assay (RIA or ECLIA). Methods: Double positive s- or e-system sera specimens (tested with ELISA) were randomly selected to be cross-checked with RIA or ECLIA. Results: The double positive rate in the specimens checked with RIA was only 31.8% for s-system and 3.37% for e- system. In the case of ECLIA, the double positive rate was 17.65% and 9.09% respectively. The results obtained with both RIA and ECLIA were significantly lower than the results with ELISA (P 0.05). Conclusion: The unusually high double positive rate of s- or e- system in HBVM detection with ELISA was due to false positiveness and results from RIA were more consistent with the results from ECLIA. (authors)

Pobreza e suas relações com a Psicologia Comunitária na 5a Conferência Internacional de Psicologia Comunitária

OpenAIRE

Verônica Morais; James Ferreira Moura Júnior; Sara Castro Lima

2015-01-01

O problema da pobreza tem influências psicossociais na vida humana. A Psicologia Comunitária trabalha com esses problemas psicossociais. Então, busca-se com este artigo analisar a presença da temática da pobreza nos trabalhos apresentados na 5ª Conferência Internacional de Psicologia Comunitária (CIPC), que foi realizada em setembro de 2014 em Fortaleza (Ceará/Brasil). O tema da 5ª CIPC foi “Psicologia Comunitária no mundo atual: desafios, limites e práticas” com 1553 inscritos e 726 trabalho...

Improving the fidelity of electrically heated nuclear systems testing using simulated neutronic feedback

International Nuclear Information System (INIS)

Bragg-Sitton, Shannon M.; Godfroy, Thomas J.; Webster, Kenny

2010-01-01

Nonnuclear test platforms and methodologies can be employed to reduce the overall cost, risk and complexity of testing nuclear systems while allowing one to evaluate the operation of an integrated nuclear system within a reasonable timeframe, providing valuable input to the overall system design. In a nonnuclear test bed, electric heaters are used to simulate the heat from nuclear fuel. Standard electric test techniques allow one to fully assess thermal, heat transfer, and stress related attributes of a given system, but these approaches fail to demonstrate the dynamic response that would be present in an integrated, fueled reactor system. The integration of thermal hydraulic hardware tests with simulated neutronic response provides a bridge between electrically heated testing and testing with nuclear fuel elements installed. By implementing a neutronic response model to simulate the dynamic response that would be expected in a fueled reactor system, one can better understand system integration issues, characterize integrated system response times and response characteristics, and assess potential design improvements at a relatively small fiscal investment. This paper summarizes the results of initial system dynamic response testing for two electrically heated reactor concepts: a heat pipe-cooled reactor simulator with integrated heat exchanger and a gas-cooled reactor simulator with integrated Brayton power conversion system. Initial applications apply a simplified reactor kinetics model with either a single or an averaged measured state point. Preliminary results demonstrate the applicability of the dynamic test methodology to any reactor type, elucidating the variation in system response characteristics in different reactor concepts. These results suggest a need to further enhance the dynamic test approach by incorporating a more accurate model of the reactor dynamics and improved hardware instrumentation for better state estimation in application of the

''Football'' test coil: a simulated service test of internally-cooled, cabled superconductor

International Nuclear Information System (INIS)

Marston, P.G.; Iwasa, Y.; Thome, R.J.; Hoenig, M.O.

1981-01-01

Internally-cooled, cabled superconductor, (ICCS), appears from small-scale tests to be a viable alternative to pool-boiling cooled superconductors for large superconducting magnets. Potential advantages may include savings in helium inventory, smaller structure and ease of fabrication. Questions remain, however, about the structural performance of these systems. The ''football'' test coil has been designed to simulate the actual ''field-current-stress-thermal'' operating conditions of a 25 ka ICCS in a commercial scale MHD magnet. The test procedure will permit demonstration of the 20 year cyclic life of such a magnet in less than 20 days. This paper describes the design, construction and test of that coil which is wound of copper-stabilized niobium-titanium cable in steel conduit. 2 refs

A culinária de sentidos : corpo e memória na literatura contemporânea

OpenAIRE

Sacramento, Adriana Rodrigues

2009-01-01

A recente publicação de textos de escritoras que relacionam Literatura e Culinária levou-me a fazer uma reflexão sobre a Memória dos Sentidos dentro de um espaço específico, a cozinha, cozinha entendida como um lugar de rito que transfigura os corpos. A partir desse recorte, procurei relacionar a representação do feminino, do corpo na cozinha e na confecção do alimento, no texto das autoras brasileiras Rachel de Queiroz, Cora Coralina, Adélia Prado, Heloísa Helena e Márcia Frazão, da mexicana...

Melancolia, memória e subjetividade

OpenAIRE

Giele Rocha Dorneles

2015-01-01

A proposta desta tese é estabelecer, através de uma perspectiva comparatista, relações entre três temas articuladores: a melancolia, a memória e a subjetividade, de modo a constituir entrelaçamentos possíveis, além de buscar indicar o modo como essas três temáticas são apresentadas e representadas em diferentes formas de expressão das artes, partindo de obras literárias - como “A maior flor do mundo” e “As pequenas memórias”, entre outras de José Saramago, e de autores como Charles Baudelaire...

Performance Test of Core Protection and Monitoring Algorithm with DLL for SMART Simulator Implementation

International Nuclear Information System (INIS)

Koo, Bonseung; Hwang, Daehyun; Kim, Keungkoo

2014-01-01

A multi-purpose best-estimate simulator for SMART is being established, which is intended to be used as a tool to evaluate the impacts of design changes on the safety performance, and to improve and/or optimize the operating procedure of SMART. In keeping with these intentions, a real-time model of the digital core protection and monitoring systems was developed and the real-time performance of the models was verified for various simulation scenarios. In this paper, a performance test of the core protection and monitoring algorithm with a DLL file for the SMART simulator implementation was performed. A DLL file of the simulator application code was made and several real-time evaluation tests were conducted for the steady-state and transient conditions with simulated system variables. A performance test of the core protection and monitoring algorithms for the SMART simulator was performed. A DLL file of the simulator version code was made and several real-time evaluation tests were conducted for various scenarios with a DLL file and simulated system variables. The results of all test cases showed good agreement with the reference results and some features caused by algorithm change were properly reflected to the DLL results. Therefore, it was concluded that the SCOPS S SIM and SCOMS S SIM algorithms and calculational capabilities are appropriate for the core protection and monitoring program in the SMART simulator

NASA Langley Distributed Propulsion VTOL Tilt-Wing Aircraft Testing, Modeling, Simulation, Control, and Flight Test Development

Science.gov (United States)

Rothhaar, Paul M.; Murphy, Patrick C.; Bacon, Barton J.; Gregory, Irene M.; Grauer, Jared A.; Busan, Ronald C.; Croom, Mark A.

2014-01-01

Control of complex Vertical Take-Off and Landing (VTOL) aircraft traversing from hovering to wing born flight mode and back poses notoriously difficult modeling, simulation, control, and flight-testing challenges. This paper provides an overview of the techniques and advances required to develop the GL-10 tilt-wing, tilt-tail, long endurance, VTOL aircraft control system. The GL-10 prototype's unusual and complex configuration requires application of state-of-the-art techniques and some significant advances in wind tunnel infrastructure automation, efficient Design Of Experiments (DOE) tunnel test techniques, modeling, multi-body equations of motion, multi-body actuator models, simulation, control algorithm design, and flight test avionics, testing, and analysis. The following compendium surveys key disciplines required to develop an effective control system for this challenging vehicle in this on-going effort.

The rare isotope accelerator (RIA) facility project

International Nuclear Information System (INIS)

Christoph Leemann

2000-01-01

The envisioned Rare-Isotope Accelerator (RIA) facility would add substantially to research opportunities for nuclear physics and astrophysics by combining increased intensities with a greatly expanded variety of high-quality rare-isotope beams. A flexible superconducting driver linac would provide 100 kW, 400 MeV/nucleon beams of any stable isotope from hydrogen to uranium onto production targets. Combinations of projectile fragmentation, target fragmentation, fission, and spallation would produce the needed broad assortment of short-lived secondary beams. This paper describes the project's background, purpose, and status, the envisioned facility, and the key subsystem, the driver linac. RIA's scientific purposes are to advance current theoretical models, reveal new manifestations of nuclear behavior, and probe the limits of nuclear existence [3]. Figures 1 and 2 show, respectively, examples of RIA research opportunities and the yields projected for pursuing them. Figure 3 outlines a conceptual approach for delivering the needed beams

Optimizing selection of in vitro tests for diagnosing thyroid disorders

International Nuclear Information System (INIS)

Zwas, S.T.; Rosenblum, Yossef; Boruchowsky, Sabina

1987-01-01

The optimal utilization of the thyroid related radioimmunoassays T3, T4, and TSH-RIA is derived from analysing the clinical and laboratory data for 974 patients with functional thyroid disorders. A statistical computer analysis of the contribution of each of the three tests, and in combination, to the final diagnoses of hypothyroid, euthyroid, and hyper thyroid states was designed. The best contributing test for hypothyroidism and euthyroidism was TSH-RIA (98.5 and 93%, respectively). T4/T3+TSH-RIAs were the optimal dual combination for diagnosing euthyroidism (98.0%). For diagnosing hyperthyroidism T4-RIA was the best single test (82.5%) followed by T3 + T4 as an optimal dual combination (95%). Using all three tests was of no significant additional value over dual combinations. It is concluded that the work and cost of randomly performing three tests routinely is not justified without clinical basis. An algorithm is proposed to guide thyroid studies based on computer analyses of the above-mentioned single or dual-test combinations to establish accurate diagnosis at the lowest laboratory cost. (author)

LOCA simulation in the NRU reactor: materials test-1

International Nuclear Information System (INIS)

Russcher, G.E.; Marshall, R.K.; Hesson, G.M.; Wildung, N.J.; Rausch, W.N.

1981-10-01

A simulated loss-of-coolant accident was performed with a full-length test bundle of pressurized water reactor fuel rods. This second experiment of the program produced peak fuel cladding temperatures of 1148K (1607 0 F) and resulted in six ruptured fuel rods. Test data and initial results from the experiment are presented here in the form of photographs and graphical summaries. These results are also compared with the preceding prototypic thermal-hydraulic test results and with computer model test predictions

Simulation software support (S3) system a software testing and debugging tool

International Nuclear Information System (INIS)

Burgess, D.C.; Mahjouri, F.S.

1990-01-01

The largest percentage of technical effort in the software development process is accounted for debugging and testing. It is not unusual for a software development organization to spend over 50% of the total project effort on testing. In the extreme, testing of human-rated software (e.g., nuclear reactor monitoring, training simulator) can cost three to five times as much as all other software engineering steps combined. The Simulation Software Support (S 3 ) System, developed by the Link-Miles Simulation Corporation is ideally suited for real-time simulation applications which involve a large database with models programmed in FORTRAN. This paper will focus on testing elements of the S 3 system. In this paper system support software utilities are provided which enable the loading and execution of modules in the development environment. These elements include the Linking/Loader (LLD) for dynamically linking program modules and loading them into memory and the interactive executive (IEXEC) for controlling the execution of the modules. Features of the Interactive Symbolic Debugger (SD) and the Real Time Executive (RTEXEC) to support the unit and integrated testing will be explored

On-going activities in the European JASMIN project for the development and validation of ASTEC-Na SFR safety simulation code - 15072

International Nuclear Information System (INIS)

Girault, N.; Cloarec, L.; Herranz, L.; Bandini, G.; Perez-Martin, S.; Ammirabile, L.

2015-01-01

The 4-year JASMIN collaborative project (Joint Advanced Severe accidents Modelling and Integration for Na-cooled fast reactors), started in Dec.2011 in the frame of the 7. Framework Programme of the European Commission. It aims at developing a new European simulation code, ASTEC-Na, dealing with the primary phase of SFR core disruptive accidents. The development of a new code, based on a robust advanced simulation tool and able to encompass the in-vessel and in-containment phenomena occurring during a severe accident is indeed of utmost interest for advanced and innovative future SFRs for which an enhanced safety level will be required. This code, based on the ASTEC European code system developed by IRSN and GRS for severe accidents in water-cooled reactors, is progressively integrating and capitalizing the state-of-the-art knowledge of SFR accidents through physical model improvement or development of new ones. New models are assessed on in-pile (CABRI, SCARABEE etc...) and out-of pile experiments conducted during the 70's-80's and code-o-code benchmarking with current accident simulation tools for SFRs is also conducted. During the 2 and a half first years of the project, model specifications and developments were conducted and the validation test matrix was built. The first version of ASTEC-Na available in early 2014 already includes a thermal-hydraulics module able to simulate single and two-phase sodium flow conditions, a zero point neutronic model with simple definition of channel and axial dependences of reactivity feedbacks and models derived from SCANAIR IRSN code for simulating fuel pin thermo-mechanical behaviour and fission gas release/retention. Meanwhile, models have been developed in the source term area for in-containment particle generation and particle chemical transformation, but their implementation is still to be done. As a first validation step, the ASTEC-Na calculations were satisfactorily compared to thermal-hydraulics experimental

Real Time Photovoltaic Array Simulator for Testing Grid-Connected PV Inverters

DEFF Research Database (Denmark)

Sera, Dezso; Valentini, Massimo; Raducu, Alin

2008-01-01

In this paper a real time flexible PV array simulator is presented. It is a system that can simulate different PV panel arrays in specific environmental conditions. To evaluate performance of the Maximum Power Point Tracking (MPPT) of grid-connected Photovoltaic (PV) inverters only measurements...... undertaken with an appropriate PV array simulator provide accurate and reproducible results. Thus the PV array simulator has been developed and implemented. MPPT efficiency tests on a commercial grid-connected PV inverter have been performed to validate the PV array simulator....

Proceedings of the topical meeting on reactivity initiated accidents (RIA)

International Nuclear Information System (INIS)

2003-01-01

The topical meeting was devoted to RIA fuel acceptance criteria, in particular to the fuel fragmentation enthalpy limit and the PCMI failure enthalpy limit in relation to high burnup fuel. In total 50 participants attended. Research and industry organisations from France, Finland, Germany, Hungary, Japan, the Russian Federation, Sweden, the United Kingdom and the USA including the Swiss regulatory body, HSK, and the Halden reactor project, presented 16 papers in all. The papers covered three main areas: 'best estimate' core calculations for RIA energy deposition in high burnup fuels, the technical background of current and new RIA fuel safety criteria, and ongoing RIA experimental programmes. A number of open issues were identified, whose resolution is expected from ongoing and planned national and international experimental programmes

Simulated Field Trials Using an Indoor Aerosol Test Chamber

National Research Council Canada - National Science Library

Semler, D. D; Roth, A. P; Semler, K. A; Nolan, P. M

2004-01-01

.... In this method, the aerosol chamber control software manipulates circulation fan speeds, chamber vacuum and agent spray times to produce a simulated dynamic cloud within the aerosol test chamber...

Simulated Field Trials Using An Indoor Aerosol Test Chamber

National Research Council Canada - National Science Library

Semler, D. D; Roth, A. P; Semler, K. A; Nolan, P. M

2004-01-01

.... In this method, the aerosol chamber control software manipulates circulation fan speeds, chamber vacuum and agent spray times to produce a simulated dynamic cloud within the aerosol test chamber...

Solar cooker effect test and temperature field simulation of radio telescope subreflector

International Nuclear Information System (INIS)

Chen, Deshen; Wang, Huajie; Qian, Hongliang; Zhang, Gang; Shen, Shizhao

2016-01-01

Highlights: • Solar cooker effect test of a telescope subreflector is conducted for the first time. • The cause and temperature distribution regularities are analyzed contrastively. • Simulation methods are proposed using light beam segmentation and tracking methods. • The validity of simulation methods is evaluated using the test results. - Abstract: The solar cooker effect can cause a local high temperature of the subreflector and can directly affect the working performance of the radio telescope. To study the daily temperature field and solar cooker effect of a subreflector, experimental studies are carried out with a 3-m-diameter radio telescope model for the first time. Initially, the solar temperature distribution rules, especially the solar cooker effect, are summarized according to the field test results under the most unfavorable conditions. Then, a numerical simulation for the solar temperature field of the subreflector is studied by light beam segmentation and tracking methods. Finally, the validity of the simulation methods is evaluated using the test results. The experimental studies prove that the solar cooker effect really exists and should not be overlooked. In addition, simulation methods for the subreflector temperature field proposed in this paper are effective. The research methods and conclusions can provide valuable references for thermal design, monitoring and control of similar high-precision radio telescopes.

História Militar do Ceará

Directory of Open Access Journals (Sweden)

Walter José Faustini

1953-03-01

Full Text Available SOUZA (Eusébio de. — História Militar do Ceará. Monografia n.o 15 da  Série História do Ceará, da Coleção Instituto do Ceará. 1950 (Obra  póstuma. (Primeiro Parágrafo do Artigo Destinada a integrar uma coleção de assuntos cearenses, a presente obra pretende historiar a evolução das instituições militares no Estado do Ceará.

Retained Gas Sampler Calibration and Simulant Tests

Energy Technology Data Exchange (ETDEWEB)

CRAWFORD, B.A.

2000-01-05

This test plan provides a method for calibration of the retained gas sampler (RGS) for ammonia gas analysis. Simulant solutions of ammonium hydroxide at known concentrations will be diluted with isotopically labeled 0.04 M ammonium hydroxide solution. Sea sand solids will also be mixed with ammonium hydroxide solution and diluent to determine the accuracy of the system for ammonia gas analysis.

Retained Gas Sampler Calibration and Simulant Tests

International Nuclear Information System (INIS)

CRAWFORD, B.A.

2000-01-01

This test plan provides a method for calibration of the retained gas sampler (RGS) for ammonia gas analysis. Simulant solutions of ammonium hydroxide at known concentrations will be diluted with isotopically labeled 0.04 M ammonium hydroxide solution. Sea sand solids will also be mixed with ammonium hydroxide solution and diluent to determine the accuracy of the system for ammonia gas analysis

Heavy-ion LINAC development for the US RIA project

Indian Academy of Sciences (India)

The Nuclear Science Community in the Unites States has unanimously concluded that developments in both nuclear science and its supporting technologies make building a world-leading Rare-Isotope Accelerator (RIA) facility for production of radioactive beams the top priority. The RIA development effort involves several ...

Federalismo e a questão tributária

OpenAIRE

Afonso, José Roberto; BNDES

2011-01-01

Em vez de fazer uma exposição convencional, listarei aqui alguns aspectos para a discussão, pois quase todo mundo no Brasil entende de reforma tributária. Metade dos brasileiros possui projeto de reforma tributária. Assim, o debate fica mais interessante.

Experimental data report for Test TS-1 Reactivity Initiated Accident Test in NSRR with pre-irradiated BWR fuel rod

International Nuclear Information System (INIS)

Nakamura, Takehiko; Yoshinaga, Makio; Sobajima, Makoto; Fujishiro, Toshio; Horiki, Ohichiro; Yamahara, Takeshi; Ichihashi, Yoshinori; Kikuchi, Teruo

1992-01-01

This report presents experimental data for Test TS-1 which was the first in a series of tests, simulating Reactivity Initiated Accident (RIA) conditions using pre-irradiated BWR fuel rods, performed in the Nuclear Safety Research Reactor (NSRR) in October, 1989. Test fuel rod used in the Test TS-1 was a short-sized BWR (7 x 7) type rod which was fabricated from a commercial rod provided from Tsuruga Unit 1 power reactor. The fuel had an initial enrichment of 2.79 % and burnup of 21.3 GWd/t (bundle average). Pulse irradiation was performed at a condition of stagnant water cooling, atmospheric pressure and ambient temperature using a newly developed double container-type capsule. Energy deposition of the rod in this test was evaluated to be about 61 cal/g·fuel (55 cal/g·fuel in peak fuel enthalpy) and no fuel failure was observed. Descriptions on test conditions, test procedures, fuel burnup measurements, transient behavior of the test rod during pulse irradiation and results of post pulse irradiation examinations are contained in this report. (author)